Structures and Mechanisms Design Concepts for Adaptive Deployable Entry Placement Technology

Science.gov (United States)

Yount, Bryan C.; Arnold, James O.; Gage, Peter J.; Mockelman, Jeffrey; Venkatapathy, Ethiraj

2012-01-01

System studies have shown that large deployable aerodynamic decelerators such as the Adaptive Deployable Entry and Placement Technology (ADEPT) concept can revolutionize future robotic and human exploration missions involving atmospheric entry, descent and landing by significantly reducing the maximum heating rate, total heat load, and deceleration loads experienced by the spacecraft during entry [1-3]. ADEPT and the Hypersonic Inflatable Aerodynamic Decelerator (HIAD) [4] share the approach of stowing the entry system in the shroud of the launch vehicle and deploying it to a much larger diameter prior to entry. The ADEPT concept provides a low ballistic coefficient for planetary entry by employing an umbrella-like deployable structure consisting of ribs, struts and a fabric cover that form an aerodynamic decelerator capable of undergoing hypersonic flight. The ADEPT "skin" is a 3-D woven carbon cloth that serves as a thermal protection system (TPS) and as a structural surface that transfers aerodynamic forces to the underlying ribs [5]. This paper focuses on design activities associated with integrating ADEPT components (cloth, ribs, struts and mechanisms) into a system that can function across all configurations and environments of a typical mission concept: stowed during launch, in-space deployment, entry, descent, parachute deployment and separation from the landing payload. The baseline structures and mechanisms were selected via trade studies conducted during the summer and fall of 2012. They are now being incorporated into the design of a ground test article (GTA) that will be fabricated in 2013. It will be used to evaluate retention of the stowed configuration in a launch environment, mechanism operation for release, deployment and locking, and static strength of the deployed decelerator. Of particular interest are the carbon cloth interfaces, underlying hot structure, (Advanced Carbon- Carbon ribs) and other structural components (nose cap, struts, and

Design and end-to-end modelling of a deployable telescope

Science.gov (United States)

Dolkens, Dennis; Kuiper, Hans

2017-09-01

Deployable optics have the potential of revolutionizing the field of high resolution Earth Observation. By offering the same resolutions as a conventional telescope, while using a much smaller launch volume and mass, the costs of high resolution image data can be brought down drastically. In addition, the technology will ultimately enable resolutions that are currently unattainable due to limitations imposed by the size of launcher fairings. To explore the possibilities and system complexities of a deployable telescope, a concept study was done to design a competitive deployable imager. A deployable telescope was designed for a ground sampling distance of 25 cm from an orbital altitude of 550 km. It offers an angular field of view of 0.6° and has a panchromatic channel as well as four multispectral bands in the visible and near infrared spectrum. The optical design of the telescope is based on an off-axis Korsch Three Mirror Anastigmat. A freeform tertiary mirror is used to ensure a diffraction limited image quality for all channels, while maintaining a compact design. The segmented primary mirror consists of four tapered aperture segments, which can be folded down during launch, while the secondary mirror is mounted on a deployable boom. In its stowed configuration, the telescope fits within a quarter of the volume of a conventional telescope reaching the same resolution. To reach a diffraction limited performance while operating in orbit, the relative position of each individual mirror segment must be controlled to a fraction of a wavelength. Reaching such tolerances with deployable telescope challenging, due to inherent uncertainties in the deployment mechanisms. Adding to the complexity is the fact that the telescope will be operating in a Low Earth Orbit (LEO) where it will be exposed to very dynamic thermal conditions. Therefore, the telescope will be equipped with a robust calibration system. Actuators underneath the primary mirror will be controlled using

Quality function deployment

International Nuclear Information System (INIS)

1981-10-01

This book indicates quality function deployment with quality and deployment of quality function, process and prospect of quality function deployment and development, product process and conception of quality table, deployment of quality demand, design of quality table and application of concurrent multi design, progress design and quality development, main safe part and management of important function part, quality development and deployment of method of construction, quality deployment and economics, total system of quality function deployment and task of quality function deployment in the present and future.

On balanced minimal repeated measurements designs

Directory of Open Access Journals (Sweden)

Shakeel Ahmad Mir

2014-10-01

Full Text Available Repeated Measurements designs are concerned with scientific experiments in which each experimental unit is assigned more than once to a treatment either different or identical. This class of designs has the property that the unbiased estimators for elementary contrasts among direct and residual effects are obtainable. Afsarinejad (1983 provided a method of constructing balanced Minimal Repeated Measurements designs p < t , when t is an odd or prime power, one or more than one treatment may occur more than once in some sequences and  designs so constructed no longer remain uniform in periods. In this paper an attempt has been made to provide a new method to overcome this drawback. Specifically, two cases have been considered                RM[t,n=t(t-t/(p-1,p], λ2=1 for balanced minimal repeated measurements designs and  RM[t,n=2t(t-t/(p-1,p], λ2=2 for balanced  repeated measurements designs. In addition , a method has been provided for constructing              extra-balanced minimal designs for special case RM[t,n=t2/(p-1,p], λ2=1.

Design, deployment and performance of 4G-LTE networks a practical approach

CERN Document Server

ElNashar, Ayman; Sherif, Mahmoud

2014-01-01

This book provides an insight into the key practical aspects and best practice of 4G-LTE network design, performance, and deployment Design, Deployment and Performance of 4G-LTE Networks addresses the key practical aspects and best practice of 4G networks design, performance, and deployment. In addition, the book focuses on the end-to-end aspects of the LTE network architecture and different deployment scenarios of commercial LTE networks. It describes the air interface of LTE focusing on the access stratum protocol layers: PDCP, RLC, MAC, and Physical Layer. The air interface described in this book covers the concepts of LTE frame structure, downlink and uplink scheduling, and detailed illustrations of the data flow across the protocol layers. It describes the details of the optimization process including performance measurements and troubleshooting mechanisms in addition to demonstrating common issues and case studies based on actual field results. The book provides detailed performance analysis of key fe...

Design and Development of NEA Scout Solar Sail Deployer Mechanism

Science.gov (United States)

Sobey, Alexander R.; Lockett, Tiffany Russell

2016-01-01

The 6U (approx.10 cm x 20 cm x 30 cm) cubesat Near Earth Asteroid (NEA) Scout1, projected for launch in September 2018 aboard the maiden voyage of the Space Launch System, will utilize a solar sail as its main method of propulsion throughout its approx.3-year mission to a Near Earth Asteroid. Due to the extreme volume constraints levied onto the mission, an acutely compact solar sail deployment mechanism has been designed to meet the volume and mass constraints, as well as provide enough propulsive solar sail area and quality in order to achieve mission success. The design of such a compact system required the development of approximately half a dozen prototypes in order to identify unforeseen problems, advance solutions, and build confidence in the final design product. This paper focuses on the obstacles of developing a solar sail deployment mechanism for such an application and the lessons learned from a thorough development process. The lessons presented will have significant applications beyond the NEA Scout mission, such as the development of other deployable boom mechanisms and uses for gossamer-thin films in space.

Research on knowledge support technology for product innovation design based on quality function knowledge deployment

Directory of Open Access Journals (Sweden)

Kai Zhang

2016-06-01

Full Text Available Based on the analysis of the relationship between the process of product innovation design and knowledge, this article proposes a theoretical model of quality function knowledge deployment. In order to link up the product innovation design and the knowledge required by the designer, the iterative method of quality function knowledge deployment is refined, as well as the knowledge retrieval model and knowledge support model based on quality function knowledge deployment are established. In the whole life cycle of product design, in view of the different requirements for knowledge in conceptual design stage, components’ configuration stage, process planning stage, and production planning stage, the quality function knowledge deployment model could link up the required knowledge with the engineering characteristics, component characteristics, process characteristics, and production characteristics in the four stages using the mapping relationship between the function characteristics and the knowledge and help the designer to track the required knowledge for realizing product innovation design. In this article, an instance about rewinding machine is given to demonstrate the practicability and validity of product innovation design knowledge support technology based on quality function knowledge deployment.

Scientific Cluster Deployment and Recovery - Using puppet to simplify cluster management

Science.gov (United States)

Hendrix, Val; Benjamin, Doug; Yao, Yushu

2012-12-01

Deployment, maintenance and recovery of a scientific cluster, which has complex, specialized services, can be a time consuming task requiring the assistance of Linux system administrators, network engineers as well as domain experts. Universities and small institutions that have a part-time FTE with limited time for and knowledge of the administration of such clusters can be strained by such maintenance tasks. This current work is the result of an effort to maintain a data analysis cluster (DAC) with minimal effort by a local system administrator. The realized benefit is the scientist, who is the local system administrator, is able to focus on the data analysis instead of the intricacies of managing a cluster. Our work provides a cluster deployment and recovery process (CDRP) based on the puppet configuration engine allowing a part-time FTE to easily deploy and recover entire clusters with minimal effort. Puppet is a configuration management system (CMS) used widely in computing centers for the automatic management of resources. Domain experts use Puppet's declarative language to define reusable modules for service configuration and deployment. Our CDRP has three actors: domain experts, a cluster designer and a cluster manager. The domain experts first write the puppet modules for the cluster services. A cluster designer would then define a cluster. This includes the creation of cluster roles, mapping the services to those roles and determining the relationships between the services. Finally, a cluster manager would acquire the resources (machines, networking), enter the cluster input parameters (hostnames, IP addresses) and automatically generate deployment scripts used by puppet to configure it to act as a designated role. In the event of a machine failure, the originally generated deployment scripts along with puppet can be used to easily reconfigure a new machine. The cluster definition produced in our CDRP is an integral part of automating cluster deployment

Deployment, Design, and Commercialization of Carbon-Negative Energy Systems

Science.gov (United States)

Sanchez, Daniel Lucio

Climate change mitigation requires gigaton-scale carbon dioxide removal technologies, yet few examples exist beyond niche markets. This dissertation informs large-scale implementation of bioenergy with carbon capture and sequestration (BECCS), a carbon-negative energy technology. It builds on existing literature with a novel focus on deployment, design, commercialization, and communication of BECCS. BECCS, combined with aggressive renewable deployment and fossil emission reductions, can enable a carbon-negative power system in Western North America by 2050, with up to 145% emissions reduction from 1990 levels. BECCS complements other sources of renewable energy, and can be deployed in a manner consistent with regional policies and design considerations. The amount of biomass resource available limits the level of fossil CO2 emissions that can still satisfy carbon emissions caps. Offsets produced by BECCS are more valuable to the power system than the electricity it provides. Implied costs of carbon for BECCS are relatively low ( 75/ton CO2 at scale) for a capital-intensive technology. Optimal scales for BECCS are an order of magnitude larger than proposed scales found in existing literature. Deviations from optimal scaled size have little effect on overall systems costs - suggesting that other factors, including regulatory, political, or logistical considerations, may ultimately have a greater influence on plant size than the techno-economic factors considered. The flexibility of thermochemical conversion enables a viable transition pathway for firms, utilities and governments to achieve net-negative CO 2 emissions in production of electricity and fuels given increasingly stringent climate policy. Primary research, development (R&D), and deployment needs are in large-scale biomass logistics, gasification, gas cleaning, and geological CO2 storage. R&D programs, subsidies, and policy that recognize co-conversion processes can support this pathway to commercialization

Hybrid deployable support truss designs for LDR

Science.gov (United States)

Hedgepeth, J.

1988-01-01

Concepts for a 20-meter diameter Large Deployable Reflector (LDR) deployable truss backup structure, and analytical predictions of its structural characteristics are discussed. The concept shown is referred to as the SIXPAC; It is a combination of the PACTRUSS concept and a single-fold beam, which would make up the desired backup structure. One advantage of retaining the PACTRUSS concept is its packaging density and its capability for synchronous deployment. Various 2-meter hexagonal panel arrangements are possible for this Hybrid PACTRUSS structure depending on the panel-to-structure attachment strategies used. Static analyses of the SIXPAC using various assumptions for truss designs and panel masses of 10 kg sq meters were performed to predict the tip displacement of the structure when supported at the center. The tip displacement ranged from 0.20 to 0.44 mm without the panel mass, and from 0.9 to 3.9 mm with the panel mass (in a 1-g field). The data indicate that the structure can be adequately ground tested to validate its required performance in space, assuming the required performance in space is approximately 100 microns. The static displacement at the tip of the structure when subjected to an angular acceleration of 0.001 rad/sec squared were estimated to range from 0.8 to 7.5 microns, depending on the type of truss elements.

Minimization In Digital Design As A Meta-Planning Problem

Science.gov (United States)

Ho, William P. C.; Wu, Jung-Gen

1987-05-01

In our model-based expert system for automatic digital system design, we formalize the design process into three sub-processes - compiling high-level behavioral specifications into primitive behavioral operations, grouping primitive operations into behavioral functions, and grouping functions into modules. Consideration of design minimization explicitly controls decision-making in the last two subprocesses. Design minimization, a key task in the automatic design of digital systems, is complicated by the high degree of interaction among the time sequence and content of design decisions. In this paper, we present an AI approach which directly addresses these interactions and their consequences by modeling the minimization prob-lem as a planning problem, and the management of design decision-making as a meta-planning problem.

Design and Development of Mobile Phone Using Quality Function Deployment

Directory of Open Access Journals (Sweden)

Hamid Ullah

2017-03-01

Full Text Available The paper presents design and development of mobile phone using Quality Function Deployment. Quality Function Deployment is one of the total quality management tools used to convert customers’ needs into design specifications. A market survey is conducted to find out the voice of customer. The Voice of the Customer is converted into customers’ needs. Relative importance is assigned to customers’ needs. A list of technical requirements that could fulfill the customers’ needs is produced. A relationship matrix is developed between the customers’ needs and the technical requirements. The relationship matrix is converted into the House of Quality. Output from the House of Quality is used in concept generation of mobile phone. Concept generation is followed by concept selection. Final improved model of the mobile phone is presented.

Scientific Cluster Deployment and Recovery – Using puppet to simplify cluster management

International Nuclear Information System (INIS)

Hendrix, Val; Yao Yushu; Benjamin, Doug

2012-01-01

Deployment, maintenance and recovery of a scientific cluster, which has complex, specialized services, can be a time consuming task requiring the assistance of Linux system administrators, network engineers as well as domain experts. Universities and small institutions that have a part-time FTE with limited time for and knowledge of the administration of such clusters can be strained by such maintenance tasks. This current work is the result of an effort to maintain a data analysis cluster (DAC) with minimal effort by a local system administrator. The realized benefit is the scientist, who is the local system administrator, is able to focus on the data analysis instead of the intricacies of managing a cluster. Our work provides a cluster deployment and recovery process (CDRP) based on the puppet configuration engine allowing a part-time FTE to easily deploy and recover entire clusters with minimal effort. Puppet is a configuration management system (CMS) used widely in computing centers for the automatic management of resources. Domain experts use Puppet's declarative language to define reusable modules for service configuration and deployment. Our CDRP has three actors: domain experts, a cluster designer and a cluster manager. The domain experts first write the puppet modules for the cluster services. A cluster designer would then define a cluster. This includes the creation of cluster roles, mapping the services to those roles and determining the relationships between the services. Finally, a cluster manager would acquire the resources (machines, networking), enter the cluster input parameters (hostnames, IP addresses) and automatically generate deployment scripts used by puppet to configure it to act as a designated role. In the event of a machine failure, the originally generated deployment scripts along with puppet can be used to easily reconfigure a new machine. The cluster definition produced in our CDRP is an integral part of automating cluster deployment

Fleet deployment, network design and hub location of liner shipping companies

DEFF Research Database (Denmark)

Gelareh, Shahin; Pisinger, David

2011-01-01

A mixed integer linear programming formulation is proposed for the simultaneous design of network and fleet deployment of a deep-sea liner service provider. The underlying network design problem is based on a 4-index (5-index by considering capacity type) formulation of the hub location problem...

LATUX: An Iterative Workflow for Designing, Validating, and Deploying Learning Analytics Visualizations

Science.gov (United States)

Martinez-Maldonado, Roberto; Pardo, Abelardo; Mirriahi, Negin; Yacef, Kalina; Kay, Judy; Clayphan, Andrew

2015-01-01

Designing, validating, and deploying learning analytics tools for instructors or students is a challenge that requires techniques and methods from different disciplines, such as software engineering, human-computer interaction, computer graphics, educational design, and psychology. Whilst each has established its own design methodologies, we now…

Design and Analysis Tools for Deployable Solar Array Systems, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Large, lightweight, deployable solar array structures have been identified as a key enabling technology for NASA with analysis and design of these structures being...

Design and Analysis Tools for Deployable Solar Array Systems, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Large, lightweight, deployable solar array structures have been identified as a key enabling technology for NASA with analysis and design of these structures being...

Structural design of the Large Deployable Reflector (LDR)

Science.gov (United States)

Satter, Celeste M.; Lou, Michael C.

1991-01-01

An integrated Large Deployable Reflector (LDR) analysis model was developed to enable studies of system responses to the mechanical and thermal disturbances anticipated during on-orbit operations. Functional requirements of the major subsystems of the LDR are investigated, design trades are conducted, and design options are proposed. System mass and inertia properties are computed in order to estimate environmental disturbances, and in the sizing of control system hardware. Scaled system characteristics are derived for use in evaluating launch capabilities and achievable orbits. It is concluded that a completely passive 20-m primary appears feasible for the LDR from the standpoint of both mechanical vibration and thermal distortions.

Structural design of the Large Deployable Reflector (LDR)

Science.gov (United States)

Satter, Celeste M.; Lou, Michael C.

1991-09-01

An integrated Large Deployable Reflector (LDR) analysis model was developed to enable studies of system responses to the mechanical and thermal disturbances anticipated during on-orbit operations. Functional requirements of the major subsystems of the LDR are investigated, design trades are conducted, and design options are proposed. System mass and inertia properties are computed in order to estimate environmental disturbances, and in the sizing of control system hardware. Scaled system characteristics are derived for use in evaluating launch capabilities and achievable orbits. It is concluded that a completely passive 20-m primary appears feasible for the LDR from the standpoint of both mechanical vibration and thermal distortions.

Curriculum and Course Design: A New Approach Using Quality Function Deployment

Science.gov (United States)

Denton, James W.; Kleist, Virginia Franke; Surendra, Nanda

2005-01-01

In this article, the authors describe a method for assuring the quality of curriculum design based on techniques that have been used in industrial settings for over 30 years. Quality Function Deployment assures that the needs of the customer are considered at all levels of product design and a graphical matrix called the House of Quality serves as…

Deployable auxetic shape memory alloy cellular antenna demonstrator: design, manufacturing and modal testing

International Nuclear Information System (INIS)

Jacobs, S; Coconnier, C; DiMaio, D; Scarpa, F; Martinez, J; Toso, M

2012-01-01

This work describes the design, manufacturing and testing of a deployable antenna for deep-space missions based on a hybrid honeycomb truss made of shape memory alloy (SMA). The deployable characteristics are enhanced by the equivalent auxetic (negative Poisson’s ratio) behaviour of the cellular configuration. Specific emphasis is placed on the modal analysis techniques used to test the lightweight SMA structure. (paper)

Risk minimization for near-term deployment of the next generation nuclear plant

International Nuclear Information System (INIS)

Lommers, L.; Southworth, F.; Riou, B.; Lecomte, M.

2008-01-01

The NGNP program is developing the High Temperature Reactor for high efficiency electricity production and high temperature process heat such as direct hydrogen production. AREVA leads one of three vendor teams supporting the NGNP program. AREVA has developed an NGNP concept based on AREVA's ANTARES indirect cycle HTR concept. The ANTARES-based NGNP concept attempts to manage development risk by using a conservative design philosophy which balances performance and risk. Additional risk mitigation for rapid near-term deployment is also considered. Near-term markets may not require the full capability of the indirect cycle very high temperature concept. A steam cycle concept might better serve near-term markets for high temperature steam with reduced technical and schedule risk. (authors)

Mastering Hyper-V Deployment

CERN Document Server

Finn, Aidan

2010-01-01

The only book to take an in-depth look at deploying Hyper-V. Now in its second generation, the popular Hyper-V boasts technical advances that create even more dynamic systems than ever before. This unique resource serves an authoritative guide to deploying Windows Server 2008 R2 Hyper-V comprehensively. Step-by-step instructions demonstrate how to design a Hyper-V deployment, build a Hyper-V host environment, and design a management system with System Center Virtual Machine Manager 2008 R2.: Features real-world examples that show you how to design a Hyper-V deployment, build a Hyper-V host env

Design and Experimental Verification of Deployable/Inflatable Ultra-Lightweight Structures

Science.gov (United States)

Pai, P. Frank

2004-01-01

Because launch cost of a space structural system is often proportional to the launch volume and mass and there is no significant gravity in space, NASA's space exploration programs and various science missions have stimulated extensive use of ultra-lightweight deployable/inflatable structures. These structures are named here as Highly Flexible Structures (HFSs) because they are designed to undergo large displacements, rotations, and/or buckling without plastic deformation under normal operation conditions. Except recent applications to space structural systems, HFSs have been used in many mechanical systems, civil structures, aerospace vehicles, home appliances, and medical devices to satisfy space limitations, provide special mechanisms, and/or reduce structural weight. The extensive use of HFSs in today's structural engineering reveals the need of a design and analysis software and a database system with design guidelines for practicing engineers to perform computer-aided design and rapid prototyping of HFSs. Also to prepare engineering students for future structural engineering requires a new and easy-to- understand method of presenting the complex mathematics of the modeling and analysis of HFSs. However, because of the high flexibility of HFSs, many unique challenging problems in the modeling, design and analysis of HFSs need to be studied. The current state of research on HFSs needs advances in the following areas: (1) modeling of large rotations using appropriate strain measures, (2) modeling of cross-section warpings of structures, (3) how to account for both large rotations and cross- section warpings in 2D (two-dimensional) and 1D structural theories, (4) modeling of thickness thinning of membranes due to inflation pressure, pretension, and temperature change, (5) prediction of inflated shapes and wrinkles of inflatable structures, (6) development of efficient numerical methods for nonlinear static and dynamic analyses, and (7) filling the gap between

Designing of self-deploying origami structures using geometrically misaligned crease patterns.

Science.gov (United States)

Saito, Kazuya; Tsukahara, Akira; Okabe, Yoji

2016-01-01

Usually, origami-based morphing structures are designed on the premise of 'rigid folding', i.e. the facets and fold lines of origami can be replaced with rigid panels and ideal hinges, respectively. From a structural mechanics viewpoint, some rigid-foldable origami models are overconstrained and have negative degrees of freedom (d.f.). In these cases, the singularity in crease patterns guarantees their rigid foldability. This study presents a new method for designing self-deploying origami using the geometrically misaligned creases. In this method, some facets are replaced by 'holes' such that the systems become a 1-d.f. mechanism. These perforated origami models can be folded and unfolded similar to rigid-foldable (without misalignment) models because of their d.f. focusing on the removed facets, the holes will deform according to the motion of the frame of the remaining parts. In the proposed method, these holes are filled with elastic parts and store elastic energy for self-deployment. First, a new extended rigid-folding simulation technique is proposed to estimate the deformation of the holes. Next, the proposed method is applied on arbitrary-size quadrilateral mesh origami. Finally, by using the finite-element method, the authors conduct numerical simulations and confirm the deployment capabilities of the models.

On Efficient Deployment of Wireless Sensors for Coverage and Connectivity in Constrained 3D Space.

Science.gov (United States)

Wu, Chase Q; Wang, Li

2017-10-10

Sensor networks have been used in a rapidly increasing number of applications in many fields. This work generalizes a sensor deployment problem to place a minimum set of wireless sensors at candidate locations in constrained 3D space to k -cover a given set of target objects. By exhausting the combinations of discreteness/continuousness constraints on either sensor locations or target objects, we formulate four classes of sensor deployment problems in 3D space: deploy sensors at Discrete/Continuous Locations (D/CL) to cover Discrete/Continuous Targets (D/CT). We begin with the design of an approximate algorithm for DLDT and then reduce DLCT, CLDT, and CLCT to DLDT by discretizing continuous sensor locations or target objects into a set of divisions without sacrificing sensing precision. Furthermore, we consider a connected version of each problem where the deployed sensors must form a connected network, and design an approximation algorithm to minimize the number of deployed sensors with connectivity guarantee. For performance comparison, we design and implement an optimal solution and a genetic algorithm (GA)-based approach. Extensive simulation results show that the proposed deployment algorithms consistently outperform the GA-based heuristic and achieve a close-to-optimal performance in small-scale problem instances and a significantly superior overall performance than the theoretical upper bound.

A Conceptual Design for a Small Deployer Satellite

Science.gov (United States)

Zumbo, S.

2002-01-01

industrial partners, has started the development of a space mission, named DeSat, focused on a new highly innovative micro satellite bus for LEO, entirely designed by an integrated team of students and researchers. The first mission is scheduled to fly at the end of 2003 on a converted Russian ICBM. The paper is intended to present the main features of DeSat mission, its goals and the activities that have been done by students and researchers to achieve the micro satellite platform design. The principal payload of the entire system is represented by a recirculating ball screw boom whose mass reaches one third of the total mass budget. The goal of the mission is to demonstrate the validity of its design also for space applications, which may range from precise off platform positioning of devices and instruments to GPS interferometry, sensor measurements and robotics. The satellite geometry, when the boom is in deployed configuration, is so stretched that the name "deployable satellite" has come out naturally. The large deployment mechanism, compared to the small bus, has influenced the design of every satellite subsystem leading to innovative solutions in terms of design, materials, equipment and instruments.

Designing and Deploying Programming Courses: Strategies, Tools, Difficulties and Pedagogy

Science.gov (United States)

Xinogalos, Stelios

2016-01-01

Designing and deploying programming courses is undoubtedly a challenging task. In this paper, an attempt to analyze important aspects of a sequence of two courses on imperative-procedural and object-oriented programming in a non-CS majors Department is made. This analysis is based on a questionnaire filled in by fifty students in a voluntary…

Deployment of pollution prevention during design -- a case study

International Nuclear Information System (INIS)

Del Mar, R.A.; Ambalam, T.T.

1997-08-01

Traditionally, pollution prevention (P2) assessments have been performed on existing facilities and ongoing operations, well after the completion of design and construction. It has been theorized that more success can be achieved by moving P2 upstream into the design process, where an estimated 70% of a project's total life cycle costs are initially fixed. Decisions made during design to prevent or minimize the amount of waste generated can reap benefits for many years to come. This is especially true when designing systems for handling hazardous and radioactive wastes for treatment, storage, and disposal. P2 assessments performed during design of such projects can uncover significant savings to be reaped during project construction, operations, and/or decommissioning. However, many project managers are still reluctant to include some type of P2 review or assessment as part of the design effort, because the immediate payback to the design entity is difficult to quantify. This paper presents the results of a P2 assessment performed on a design project at Hanford which identified close to $500,000 in construction savings while minimizing low-level and mixed radioactive waste generation. This paper describes the process used to per-form the assessment, discusses its results, and provides lessons-learned for future P2 design assessments

Advanced nuclear power systems: Design, technology, safety and strategies for their deployment

International Nuclear Information System (INIS)

1994-01-01

The objectives of the symposium were to provide high level decision makers with an overview of the discussion concerning the need for nuclear power and salient features of advanced nuclear power systems; a forum for discussing the design objectives and safety approaches for such systems and the views of regulatory bodies; a forum for identifying barriers to the deployment of these systems and for reviewing strategies to overcome these barriers; and a forum for reviewing options for international cooperation in the development and deployment of such systems. Refs, figs and tabs

Simultaneous Fleet Deployment and Network Design of Liner Shipping

DEFF Research Database (Denmark)

Gelareh, Shahin; Pisinger, David

A mixed integer linear programming formulation is proposed for the simultaneous design of network and fleet deployment of a liner service providers for deep-sea shipping. The underlying network design problem is based on a 4-index (5-index by considering capacity type) formulation of the hub...... location problem which are known for their tightness. The demand is considered to be elastic in the sense that the service provider can accept any fraction of the origin-destination demand. We then propose a primal decomposition method to solve instances of the problem to optimality. Numerical results...... confirm superiority of our approach in comparison with a general-purpose mixed integer programming solver....

A Quality Function Deployment (QFD) approach to designing a prosthetic myoelectric hand

OpenAIRE

Erika Sofía Olaya Escobar; Carlos Julio Cortés Rodríguez; Óscar Germán Duarte Velasco

2005-01-01

This paper presents a Quality Function Deployment (QFD) model based on computing with words. It is specifically used in the House of Quality (HOQ) construction phase. It illustrates the methodology employed in designing a prosthetic myoelectric hand.

Design and validation of a model to offer environmental consulting services to minimize oil pollution at gas stations: case study: a gas station in Costa Rica

International Nuclear Information System (INIS)

Calderon Hernandez, Teresita

2016-01-01

An environmental consulting service was designed and validated to minimize hydrocarbon contamination at gas stations, to be used by Migliore S.A. in order to strengthen and increase the number of services offered in the market niche of these companies. A matrix was synthesized with tools such as SWOT, deployment of the Quality Function Deployment (QFD) and international analysis. With the standardized protocols it will be possible to increase in a fluid way, the offer of consulting services. The final validation of the model allowed to verify the functionality of the same, through the generation of solid evaluation criteria that allowed a good knowledge of the gas station, case study, to offer a timely solution to your particular case, in a simple way and harmonious. The company providing environmental consulting services Migliore S.A. can count on a better commercial development, using the designed model [es

A Quality Function Deployment (QFD approach to designing a prosthetic myoelectric hand

Directory of Open Access Journals (Sweden)

Erika Sofía Olaya Escobar

2005-05-01

Full Text Available This paper presents a Quality Function Deployment (QFD model based on computing with words. It is specifically used in the House of Quality (HOQ construction phase. It illustrates the methodology employed in designing a prosthetic myoelectric hand.

Barriers to development and deployment of innovative waste minimization technologies

International Nuclear Information System (INIS)

Flores, E.A.; Donaghue, J.F.

1994-08-01

Increasing regulation and scrutiny is driving waste generators towards reducing the use of scarce natural resources and reducing or eliminating was streams. There is increasing emphasis on developing and deploying technologies that meet industry needs for recovering valuable materials in a cost-effective manner. At the Department of Energy's (DOE) Hanford Site, Battelle operates Pacific Northwest Laboratory (PNL). PNL's mission is to develop technologies to clean up the environment, and to assist industry in being competitive on a global scale. One such technology developed by PNL is the Waste Acid Detoxification and Reclamation (WADR) process. This technology recovers acids from metal-bearing spent solutions, separating out the metals (which are a valuable byproduct of the acid recycling operation) from the acids. WADR uses selective precipitation and distillation together in an innovative waste recycling technology. Selective precipitation removes the heavy metals, and vacuum distillation recovers clean acid. However, WADR and other innovative waste reduction technologies face numerous barriers to successful development and deployment in the field

A radioisotope production cyclotron designed to minimize dose

International Nuclear Information System (INIS)

Szlavik, F.F.; Moritz, L.E.

1992-01-01

This paper describes a radioisotope production cyclotron which has been designed to minimize the dose to personnel during operation and maintenance. The design incorporates lessons learned from the operation of a CP42 cyclotron and has resulted in a reduction of the dose by a factor of more than 10. (author)

Pervasive surveillance-agent system based on wireless sensor networks: design and deployment

International Nuclear Information System (INIS)

Martínez, José F; Bravo, Sury; García, Ana B; Corredor, Iván; Familiar, Miguel S; López, Lourdes; Hernández, Vicente; Da Silva, Antonio

2010-01-01

Nowadays, proliferation of embedded systems is enhancing the possibilities of gathering information by using wireless sensor networks (WSNs). Flexibility and ease of installation make these kinds of pervasive networks suitable for security and surveillance environments. Moreover, the risk for humans to be exposed to these functions is minimized when using these networks. In this paper, a virtual perimeter surveillance agent, which has been designed to detect any person crossing an invisible barrier around a marked perimeter and send an alarm notification to the security staff, is presented. This agent works in a state of 'low power consumption' until there is a crossing on the perimeter. In our approach, the 'intelligence' of the agent has been distributed by using mobile nodes in order to discern the cause of the event of presence. This feature contributes to saving both processing resources and power consumption since the required code that detects presence is the only system installed. The research work described in this paper illustrates our experience in the development of a surveillance system using WNSs for a practical application as well as its evaluation in real-world deployments. This mechanism plays an important role in providing confidence in ensuring safety to our environment

Conceptual Design of Deployment Structure of Morphing Nose Cone

Directory of Open Access Journals (Sweden)

Junlan Li

2013-01-01

Full Text Available For a reusable space vehicle or a missile, the shape of the nose cone has a significant effect on the drag of the vehicle. In this paper, the concept of morphing nose cone is proposed to reduce the drag when the reentry vehicle flies back into the atmosphere. The conceptual design of the structure of morphing nose cone is conducted. Mechanical design and optimization approach are developed by employing genetic algorithm to find the optimal geometric parameters of the morphing structure. An example is analyzed by using the proposed method. The results show that optimal solution supplies the minimum position error. The concept of morphing nose cone will provide a novel way for the drag reduction of reentry vehicle. The proposed method could be practically used for the design and optimization of the deployable structure of morphing nose cone.

Designing a total data solution technology, implementation, and deployment

CERN Document Server

Burkey, Roxanne

2000-01-01

Your company's global competitiveness depends on the utilization and maintenance of information. Current data handling practices-storing, updating, and accessing data-can be either a problem or a significant strategic advantage for your company. Designing a Total Data Storage Solution: Technology, Implementation, and Deployment gives you the information you need to compare current technologies and determine which is best suited to your enterprise.This book defines and explains the components that make up total cost of ownership along with the impact of integrating current changes in technology

Deployment of an in-house designed training process in a quaternary care hospital.

Science.gov (United States)

Kumar, Ajit; Bhatia, Saurabh; Chiang, I-Jen

2013-01-01

Healthcare providers, such as doctors and nurses, have been famous for high resistance to change. A careful change management plan, particularly training process, is utmost necessary. A quaternary care hospital in India changed its system, from manual to Electronic Medical Record/Health Information System (EMR/HIS). The hospital management wanted to train its 4000 diverse end-users on the EMR/HIS in two months' time. This paper describes an in-house designed training process and its deployment in the given healthcare organizational settings. We designed a training process named DRIPDA. The training process was deployed to train 4000 end-users of EMR/HIS, in the quaternary care hospital. Various factors, such as methods and tools of training, constraints of trainees, trainers, and organization were considered while deploying the training process. The effectiveness of the DRIPDA was assessed using the Kirkpatrick model. End-users received training on the new system only in 25% of estimated time and 28% of the projected expense, without having any distraction in their usual workflow, or any productivity loss. We found that the DRIPDA training process could train all employees effectively and efficiently. A decent training process can help in managing the change, thereby reduce the training time and cost.

Design and optimization of a self-developing single axis tracking PV array

International Nuclear Information System (INIS)

Colozza, A.J.

1992-01-01

This paper reports on a study performed in order to design a tracking PV array and optimize the design for maximum specific power. The design considerations were minimal deployment time, high reliability and small stowage volume. The array design was self-deployable, from a compact stowage configuration, using a passive pressurized gas deployment mechanism. The array structural components consist of a combination of beams, columns and cables used to deploy and orient a flexible PV blanket. Each structural component of the design was analyzed to determine the size necessary to withstand the various forces it would be subjected to. An optimization was performed to determine the array dimensions and blanket geometry which produce the maximum specific power

Designing, developing, and deploying systems to support human-robot teams in disaster response

NARCIS (Netherlands)

Kruijff, G.J.M.; Kruijff-Korbayová, I.; Keshavdas, S.; Larochelle, B.; Janíček, M.; Colas, F.; Liu, M.; Pomerleau, F.; Siegwart, R.; Neerincx, M.A.; Looije, R.; Smets, N.J.J.M.; Mioch, T.; Diggelen, J. van; Pirri, F.; Gianni, M.; Ferri, F.; Menna, M.; Worst, R.; Linder, T.; Tretyakov, V.; Surmann, H.; Svoboda, T.; Reinštein, M.; Zimmermann, K.; Petříček, T.; Hlaváč, V.

2014-01-01

This paper describes our experience in designing, developing and deploying systems for supporting human-robot teams during disaster response. It is based on R&D performed in the EU-funded project NIFTi. NIFTi aimed at building intelligent, collaborative robots that could work together with humans in

Minimizing System Modification in an Incremental Design Approach

DEFF Research Database (Denmark)

Pop, Paul; Eles, Petru; Pop, Traian

2001-01-01

In this paper we present an approach to mapping and scheduling of distributed embedded systems for hard real-time applications, aiming at minimizing the system modification cost. We consider an incremental design process that starts from an already existing sys-tem running a set of applications. We...

A randomized multicenter trial of minimally invasive rapid deployment versus conventional full sternotomy aortic valve replacement.

Science.gov (United States)

Borger, Michael A; Moustafine, Vadim; Conradi, Lenard; Knosalla, Christoph; Richter, Markus; Merk, Denis R; Doenst, Torsten; Hammerschmidt, Robert; Treede, Hendrik; Dohmen, Pascal; Strauch, Justus T

2015-01-01

Minimally invasive surgical procedures (MIS) may offer several advantages over conventional full sternotomy (FS) aortic valve replacement (AVR). A novel class of aortic valve prostheses has been developed for rapid-deployment AVR (RDAVR). We report a randomized, multicenter trial comparing the outcomes for MIS-RDAVR with those of conventional FS-AVR. A total of 100 patients with aortic stenosis were enrolled in a prospective, multicenter, randomized comparison trial (CADENCE-MIS). Exclusion criteria included ejection fraction below 25%, AVR requiring concomitant procedures, and recent myocardial infarction or stroke. Patients were randomized to undergo MIS-RDAVR through an upper hemisternotomy (n = 51) or AVR by FS with a conventional stented bioprosthesis (n = 49). Three patients were excluded before the procedure, and 3 more patients who were randomized to undergo RDAVR were excluded because of their anatomy. Procedural, early clinical outcomes, and functional outcomes were assessed for the remaining 94 patients. Hemodynamic performance was assessed by an echocardiography core laboratory. Implanted valve sizes were similar between groups (22.9 ± 2.1 vs 23.0 ± 2.1 mm, p = 0.9). MIS-RDAVR was associated with significantly reduced aortic cross-clamp times compared with FS-AVR (41.3 ± 20.3 vs 54.0 ± 20.3 minutes, p quality of life measures. The RDAVR patients had a significantly lower mean transvalvular gradient (8.5 vs 10.3 mm Hg, p = 0.044) and a lower prevalence of patient-prosthesis mismatch (0% vs 15.0%, p = 0.013) 3 months postoperatively compared with the FS-AVR patients. RDAVR by the MIS approach is associated with significantly reduced myocardial ischemic time and better valvular hemodynamic function than FS-AVR with a conventional stented bioprosthesis. Rapid deployment valves may facilitate the performance of MIS-AVR. Copyright © 2015 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Design and Deployment of a Multichroic Polarimeter Array on the Atacama Cosmology Telescope

Science.gov (United States)

Datta, R.; Austermann, J.; Beall, J. A.; Becker, D.; Coughlin, K. P.; Duff, S. M.; Gallardo, P.A.; Grace, E.; Hasselfield, M.; Henderson, S. W.;

Design and Deployment of a Multichroic Polarimeter Array on the Atacama Cosmology Telescope

Science.gov (United States)

Datta, R.; Austermann, J.; Beall, J. A.; Becker, D.; Coughlin, K. P.; Duff, S. M.; Gallardo, P. A.; Grace, E.; Hasselfield, M.; Henderson, S. W.; Hilton, G. C.; Ho, S. P.; Hubmayr, J.; Koopman, B. J.; Lanen, J. V.; Li, D.; McMahon, J.; Munson, C. D.; Nati, F.; Niemack, M. D.; Page, L.; Pappas, C. G.; Salatino, M.; Schmitt, B. L.; Schillaci, A.; Simon, S. M.; Staggs, S. T.; Stevens, J. R.; Vavagiakis, E. M.; Ward, J. T.; Wollack, E. J.

2016-08-01

We present the design and the preliminary on-sky performance with respect to beams and passbands of a multichroic polarimeter array covering the 90 and 146 GHz cosmic microwave background bands and its enabling broad-band optical system recently deployed on the Atacama Cosmology Telescope (ACT). The constituent pixels are feedhorn-coupled multichroic polarimeters fabricated at NIST. This array is coupled to the ACT telescope via a set of three silicon lenses incorporating novel broad-band metamaterial anti-reflection coatings. This receiver represents the first multichroic detector array deployed for a CMB experiment and paves the way for the extensive use of multichroic detectors and broad-band optical systems in the next generation of CMB experiments.

Tether Deployer And Brake

Science.gov (United States)

Carroll, Joseph A.; Alexander, Charles M.

1993-01-01

Design concept promises speed, control, and reliability. Scheme for deploying tether provides for fast, free, and snagless payout and fast, dependable braking. Developed for small, expendable tethers in outer space, scheme also useful in laying transoceanic cables, deploying guidance wires to torpedoes and missiles, paying out rescue lines from ship to ship via rockets, deploying antenna wires, releasing communication and power cables to sonobuoys and expendable bathythermographs, and in reeling out lines from fishing rods.

Minimal Edge-Transitive Nets for the Design and Construction of Metal-Organic Frameworks

KAUST Repository

Eddaoudi, Mohamed

2017-04-05

Highly-connected and minimal edge-transitive nets (with one or two kinds of edge) can be regarded as ideal blueprints for the rational design and construction of metal-organic frameworks (MOFs). Here we report and affirm the prominence of highly-connected nets as suitable targets in reticular chemistry for the design and synthesis of MOFs. Of special interest are augmented highly-connected binodal edge-transitive nets embedding a unique and precise positioning and connectivity of the net vertex figures, regarded as net-coded building units (net-cBUs). Explicitly, a definite net-cBU encompasses precise geometrical information that codes uniquely and matchlessly a selected net, a compelling perquisite for the rational design of MOFs. Interestingly, the double six-membered ring (d6R) building unit offers great prospective to be deployed as a net-cBU for the deliberate reticulation of the sole two edge-transitive nets with a vertex figure as a d6R, namely the (4,12)-coordinated shp net (square and hexagonal prism) and the (6,12)-coordinated alb net (aluminium diboride, hexagonal prism and trigonal prism). Conceivably, we envisioned and proposed various MOF structures based on the derived shp and alb nets. Gaining access to the requisite net-cBUs is essential for the successful practice of reticular chemistry; correspondingly organic and organic chemistries were deployed to afford concomitant molecular building blocks (MBBs) with the looked-for shape and connectivity. Practically, the combination of the 12-connected (12-c) rare-earth (RE) polynuclear, points of extension matching the 12 vertices of the hexagonal prism (d6R) with a 4-connected tetracarboxylate ligand or a 6-connected hexacarboxylate ligand afforded the targeted shp-MOF or alb-MOF, respectively. Intuitively, a dodecacarboxylate ligand can be conceived and purported as a compatible 12-c MBB, plausibly affording the positioning of the carbon centers of the twelve carboxylate groups on the vertices of the

A Web Centric Architecture for Deploying Multi-Disciplinary Engineering Design Processes

Science.gov (United States)

Woyak, Scott; Kim, Hongman; Mullins, James; Sobieszczanski-Sobieski, Jaroslaw

2004-01-01

There are continuous needs for engineering organizations to improve their design process. Current state of the art techniques use computational simulations to predict design performance, and optimize it through advanced design methods. These tools have been used mostly by individual engineers. This paper presents an architecture for achieving results at an organization level beyond individual level. The next set of gains in process improvement will come from improving the effective use of computers and software within a whole organization, not just for an individual. The architecture takes advantage of state of the art capabilities to produce a Web based system to carry engineering design into the future. To illustrate deployment of the architecture, a case study for implementing advanced multidisciplinary design optimization processes such as Bi-Level Integrated System Synthesis is discussed. Another example for rolling-out a design process for Design for Six Sigma is also described. Each example explains how an organization can effectively infuse engineering practice with new design methods and retain the knowledge over time.

Design Development of a Combined Deployment and Pointing System for the International Space Station Neutron Star Interior Composition Explorer Telescope

Science.gov (United States)

Budinoff, Jason; Gendreau, Keith; Arzoumanian, Zaven; Baker, Charles; Berning, Robert; Colangelo, TOdd; Holzinger, John; Lewis, Jesse; Liu, Alice; Mitchell, Alissa;

Single liner shipping service design

DEFF Research Database (Denmark)

Plum, Christian Edinger Munk; Pisinger, David; Salazar-González, Juan-José

2014-01-01

The design of container shipping networks is an important logistics problem, involving assets and operational costs measured in billions of dollars. To guide the optimal deployment of the ships, a single vessel round trip is considered by minimizing operational costs and flowing the best paying...

CMS software deployment on OSG

International Nuclear Information System (INIS)

Kim, B; Avery, P; Thomas, M; Wuerthwein, F

2008-01-01

A set of software deployment tools has been developed for the installation, verification, and removal of a CMS software release. The tools that are mainly targeted for the deployment on the OSG have the features of instant release deployment, corrective resubmission of the initial installation job, and an independent web-based deployment portal with Grid security infrastructure login mechanism. We have been deploying over 500 installations and found the tools are reliable and adaptable to cope with problems with changes in the Grid computing environment and the software releases. We present the design of the tools, statistics that we gathered during the operation of the tools, and our experience with the CMS software deployment on the OSG Grid computing environment

CMS software deployment on OSG

Energy Technology Data Exchange (ETDEWEB)

Kim, B; Avery, P [University of Florida, Gainesville, FL 32611 (United States); Thomas, M [California Institute of Technology, Pasadena, CA 91125 (United States); Wuerthwein, F [University of California at San Diego, La Jolla, CA 92093 (United States)], E-mail: bockjoo@phys.ufl.edu, E-mail: thomas@hep.caltech.edu, E-mail: avery@phys.ufl.edu, E-mail: fkw@fnal.gov

2008-07-15

A set of software deployment tools has been developed for the installation, verification, and removal of a CMS software release. The tools that are mainly targeted for the deployment on the OSG have the features of instant release deployment, corrective resubmission of the initial installation job, and an independent web-based deployment portal with Grid security infrastructure login mechanism. We have been deploying over 500 installations and found the tools are reliable and adaptable to cope with problems with changes in the Grid computing environment and the software releases. We present the design of the tools, statistics that we gathered during the operation of the tools, and our experience with the CMS software deployment on the OSG Grid computing environment.

Optimal design method to minimize users' thinking mapping load in human-machine interactions.

Science.gov (United States)

Huang, Yanqun; Li, Xu; Zhang, Jie

2015-01-01

The discrepancy between human cognition and machine requirements/behaviors usually results in serious mental thinking mapping loads or even disasters in product operating. It is important to help people avoid human-machine interaction confusions and difficulties in today's mental work mastered society. Improving the usability of a product and minimizing user's thinking mapping and interpreting load in human-machine interactions. An optimal human-machine interface design method is introduced, which is based on the purpose of minimizing the mental load in thinking mapping process between users' intentions and affordance of product interface states. By analyzing the users' thinking mapping problem, an operating action model is constructed. According to human natural instincts and acquired knowledge, an expected ideal design with minimized thinking loads is uniquely determined at first. Then, creative alternatives, in terms of the way human obtains operational information, are provided as digital interface states datasets. In the last, using the cluster analysis method, an optimum solution is picked out from alternatives, by calculating the distances between two datasets. Considering multiple factors to minimize users' thinking mapping loads, a solution nearest to the ideal value is found in the human-car interaction design case. The clustering results show its effectiveness in finding an optimum solution to the mental load minimizing problems in human-machine interaction design.

Design of an application using microservices architecture and its deployment in the cloud

OpenAIRE

Fernández Garcés, Lidia

2016-01-01

The design of modern large business application systems is moving from monolithic enterprise architectures towards microservices based architectures. These are especially well suited to run in cloud environments, because each microservice can be developed, deployed and managed individually, which allows much more fine-grained control and scalability. Based on a concrete example, this projet should build an application using a microservice architecture, showi...

A majorization-minimization approach to design of power distribution networks

Energy Technology Data Exchange (ETDEWEB)

Johnson, Jason K [Los Alamos National Laboratory; Chertkov, Michael [Los Alamos National Laboratory

2010-01-01

We consider optimization approaches to design cost-effective electrical networks for power distribution. This involves a trade-off between minimizing the power loss due to resistive heating of the lines and minimizing the construction cost (modeled by a linear cost in the number of lines plus a linear cost on the conductance of each line). We begin with a convex optimization method based on the paper 'Minimizing Effective Resistance of a Graph' [Ghosh, Boyd & Saberi]. However, this does not address the Alternating Current (AC) realm and the combinatorial aspect of adding/removing lines of the network. Hence, we consider a non-convex continuation method that imposes a concave cost of the conductance of each line thereby favoring sparser solutions. By varying a parameter of this penalty we extrapolate from the convex problem (with non-sparse solutions) to the combinatorial problem (with sparse solutions). This is used as a heuristic to find good solutions (local minima) of the non-convex problem. To perform the necessary non-convex optimization steps, we use the majorization-minimization algorithm that performs a sequence of convex optimizations obtained by iteratively linearizing the concave part of the objective. A number of examples are presented which suggest that the overall method is a good heuristic for network design. We also consider how to obtain sparse networks that are still robust against failures of lines and/or generators.

Minimizing student’s faults in determining the design of experiment through inquiry-based learning

Science.gov (United States)

Nilakusmawati, D. P. E.; Susilawati, M.

2017-10-01

The purpose of this study were to describe the used of inquiry method in an effort to minimize student’s fault in designing an experiment and to determine the effectiveness of the implementation of the inquiry method in minimizing student’s faults in designing experiments on subjects experimental design. This type of research is action research participants, with a model of action research design. The data source were students of the fifth semester who took a subject of experimental design at Mathematics Department, Faculty of Mathematics and Natural Sciences, Udayana University. Data was collected through tests, interviews, and observations. The hypothesis was tested by t-test. The result showed that the implementation of inquiry methods to minimize of students fault in designing experiments, analyzing experimental data, and interpret them in cycle 1 students can reduce fault by an average of 10.5%. While implementation in Cycle 2, students managed to reduce fault by an average of 8.78%. Based on t-test results can be concluded that the inquiry method effectively used to minimize of student’s fault in designing experiments, analyzing experimental data, and interpreting them. The nature of the teaching materials on subject of Experimental Design that demand the ability of students to think in a systematic, logical, and critical in analyzing the data and interpret the test cases makes the implementation of this inquiry become the proper method. In addition, utilization learning tool, in this case the teaching materials and the students worksheet is one of the factors that makes this inquiry method effectively minimizes of student’s fault when designing experiments.

Net Metering and Market Feedback Loops: Exploring the Impact of Retail Rate Design on Distributed PV Deployment

Energy Technology Data Exchange (ETDEWEB)

Darghouth, Naïm R. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wiser, Ryan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Barbose, Galen [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Mills, Andrew [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2015-01-13

The substantial increase in deployment of customer-sited solar photovoltaics (PV) in the United States has been driven by a combination of steeply declining costs, financing innovations, and supportive policies. Among those supportive policies is net metering, which in most states effectively allows customers to receive compensation for distributed PV generation at the full retail electricity price. The current design of retail electricity rates and the presence of net metering have elicited concerns that the possible under-recovery of fixed utility costs from PV system owners may lead to a feedback loop of increasing retail prices that accelerate PV adoption and further rate increases. However, a separate and opposing feedback loop could offset this effect: increased PV deployment may lead to a shift in the timing of peak-period electricity prices that could reduce the bill savings received under net metering where time-varying retail electricity rates are used, thereby dampening further PV adoption. In this paper, we examine the impacts of these two competing feedback dynamics on U.S. distributed PV deployment through 2050 for both residential and commercial customers, across states. Our results indicate that, at the aggregate national level, the two feedback effects nearly offset one another and therefore produce a modest net effect, although their magnitude and direction vary by customer segment and by state. We also model aggregate PV deployment trends under various rate designs and net-metering rules, accounting for feedback dynamics. Our results demonstrate that future adoption of distributed PV is highly sensitive to retail rate structures. Whereas flat, time-invariant rates with net metering lead to higher aggregate national deployment levels than the current mix of rate structures (+5% in 2050), rate structures with higher monthly fixed customer charges or PV compensation at levels lower than the full retail rate can dramatically erode aggregate customer

The VolturnUS 1:8 Floating Wind Turbine: Design, Construction, Deployment, Testing, Retrieval, and Inspection of the First Grid-Connected Offshore Wind Turbine in US

Energy Technology Data Exchange (ETDEWEB)

Dagher, Habib [Univ. of Maine, Orono, ME (United States); Viselli, Anthony [Univ. of Maine, Orono, ME (United States); Goupee, Andrew [Univ. of Maine, Orono, ME (United States); Kimball, Richard [Maine Maritime Academy, Castine, ME (United States); Allen, Christopher [Univ. of Maine, Orono, ME (United States)

2017-08-15

Volume II of the Final Report for the DeepCwind Consortium National Research Program funded by US Department of Energy Award Number: DE-EE0003278.001 summarizes the design, construction, deployment, testing, numerical model validation, retrieval, and post-deployment inspection of the VolturnUS 1:8-scale floating wind turbine prototype deployed off Castine, Maine on June 2nd, 2013. The 1:8 scale VolturnUS design served as a de-risking exercise for a commercial multi-MW VolturnUS design. The American Bureau of Shipping Guide for Building and Classing Floating Offshore Wind Turbine Installations was used to design the prototype. The same analysis methods, design methods, construction techniques, deployment methods, mooring, and anchoring planned for full-scale were used. A commercial 20kW grid-connected turbine was used and was the first offshore wind turbine in the US.

Equipment for deployment of canisters with spent nuclear fuel and bentonite buffer in horizontal holes

International Nuclear Information System (INIS)

Henttonen, V.; Suikki, M.

1992-08-01

The study presents the predesign of equipment for the deployment of canisters in long horizontal holes. The canisters are placed in the centre of the hole and are surrounded by a bentonite buffer. In thE study the canisters are assumed to have a diameter of 1.6 m and a length of 5.9 m, including the hemispherical ends. Their total weight is 60 tonnes. The bentonite buffer after homogenization is 400 mm thick, making a total package diameter of 2.4 m. The deployment system consists of four wagons for handling The canisters and the bentonite blocks. To ensure safe emplacement, every part is installed separately in its final position. This also makes it possible to use small clearances between the canisters and the bentonite blocks and between the blocks and the rock wall. With small clearances, backfilling can be avoided. Another basic design idea is that the wagons are equipped with wheels, which are in direct contact with the rock walls. Thus, rails, which have to be removed as the deployment progresses, are unnecessary. To minimize the time taken for deploying one canister, the wagons are designed so that only three trips from the service area to the deposit area are needed. Due to the radiation in the vicinity of the canisters, the wagons have to be teleoperated

Equipment for deployment of canisters with spent nuclear fuel and bentonite buffer in horisontal holes

International Nuclear Information System (INIS)

Henttonen, V.; Suikki, M.

1992-06-01

This study presents the predesign of equipment for the deployment of canisters in long horizontal holes. The canisters are placed in the centre of the hole and are surrounded by a bentonite buffer. In this study the canisters are assumed to have a diameter of 1.6 m and a length of 5.9 m, including the hemispherical ends. Their total weight is 60 tonnes. The bentonite buffer after homogenization is 400 mm thick, making a total package diameter of 2.4 m. The deployment system consists of four wagons for handling the canisters and the bentonite blocks. To ensure safe emplacement, every part is installed separately in its final position. This also makes it possible to use small clearances between the canisters and the bentonite blocks and between the blocks and the rock wall. With small clearances, backfilling can be avoided. Another basic design idea is that the wagons are equipped with wheels, which are in direct contact with the rock walls. Thus, rails, which have to be removed as the deployment progresses, are unnecessary. To minimize the time taken for deploying one canister, the wagons are designed so that only three trips from the service area to the deposit area are needed. Due to the radiation in the vicinity of the canisters, the wagons have to be teleoperated. (au)

IRIS (International Reactor Innovative and Secure) - design overview and deployment prospects

International Nuclear Information System (INIS)

Carelli, M.D.; Petrovic, B.; Cavlina, N.; Grgic, D.

2005-01-01

The International Reactor Innovative and Secure (IRIS) is an advanced, integral, lightwater cooled, pressurized reactor of medium generating capacity (1000 MWt, or about 335 MWe). It has been under development since the turn of the century by an international team - led by Westinghouse - that includes 19 organizations from 10 countries. In year 2002 it has initiated the pre-application review with the U.S. Nuclear Regulatory Commission (NRC), aiming at final design approval around 2010, and deployment in next decade (about 2015), consistent with the prediction of the growing energy supply gap in both developing and developed countries. This paper describes the reactor layout (i.e., its integral design, with the steam generators, pumps, pressurizer and control rod drive mechanisms all included inside the reactor vessel, together with the core, control rods, and neutron reflector/shield) and discusses the unique s afety-by-design T M IRIS philosophy. This approach, by eliminating accidents at the design stage, or decreasing their consequences and probabilities when outright elimination is not possible, provides a very powerful first level of defense in depth. The ''safety-bydesign'' TM allows a significant reduction and simplification of the passive safety systems, which not only improves its safety but simultaneously reduces the overall cost. Moreover, it supports licensing the power plant with reduced off-site emergency response requirements. The modular IRIS - with each module rated at ∼335 MWe - is an ideal size for smaller energy grids as it allows introducing sequentially single modules in regions only requiring a few hundred MWs at a time. IRIS naturally can be also deployed in multiple modules in areas requiring a larger amount of power increasing with time, thus fulfilling the needs of larger, developed countries as well. The performed top-down economic analysis indicates that the cost of generated electricity is competitive with other nuclear and non

Multi-purpose deployer for ITER in-vessel maintenance

Energy Technology Data Exchange (ETDEWEB)

Choi, Chang-Hwan, E-mail: Chang-Hwan.CHOI@iter.org [ITER Organization, Route de Vinon-sur-Verdon, 13115 St Paul lez Durance (France); Tesini, Alessandro; Subramanian, Rajendran [ITER Organization, Route de Vinon-sur-Verdon, 13115 St Paul lez Durance (France); Rolfe, Alan; Mills, Simon; Scott, Robin; Froud, Tim; Haist, Bernhard; McCarron, Eddie [Oxford Technologies Ltd., 7 Nuffield Way, Abingdon, OXON (United Kingdom)

2015-10-15

Highlights: • ITER RH system called as the multi-purpose deployer (MPD) is introduced. • The MPD performs dust and tritium inventory control, in-service inspection. • The MPD performs leak localization, in-vessel diagnostics maintenance. • The MPD has nine degrees of freedom with a payload capacity up to 2 tons. - Abstract: The multi-purpose deployer (MPD) is a general purpose in-vessel remote handling (RH) system in the ITER RH system. The MPD provides the means for deployment and handling of in-vessel tools or components inside the vacuum vessel (VV) for dust and tritium inventory control, in-service inspection, leak localization, and in-vessel diagnostics. It also supports the operation of blanket first wall maintenance and neutral beam duct liner module maintenance operations. This paper describes the concept design of the MPD. The MPD is a cask based system, i.e. it stays in the hot cell building during the machine operation, and is deployed to the VV using the cask system for the in-vessel operations. The main part of the MPD is the articulated transporter which provides transportation and positioning of the in-vessel tools or components. The articulated transporter has nine degrees of freedom with a payload capacity up to 2 tons. The articulated transporter can cover the whole internal surface of the VV by switching between the four equatorial RH ports. Additionally it can use two non-RH equatorial ports to transfer large tools or components. A concept for in-cask tool exchange is developed which minimizes the cask transportation by allowing the MPD to stay in the VV during the tool exchange.

Intricacies of Using Kevlar and Thermal Knives in a Deployable Release System: Issues and Solutions

Science.gov (United States)

Stewart, Alphonso C.; Hair, Jason H.; Broduer, Steve (Technical Monitor)

2002-01-01

The utilization of Kevlar cord and thermal knives in a deployable release system produces a number of issues that must be addressed in the design of the system. This paper proposes design considerations that minimize the major issues, thermal knife failure, Kevlar cord relaxation, and the measurement of the cord tension. Design practices can minimize the potential for thermal knife laminate and element damage that result in failure of the knife. A process for in-situ inspection of the knife with resistance, rather than continuity, checks and 10x zoom optical imaging can detect damaged knives. Tests allow the characterization of the behavior of the particular Kevlar cord in use and the development of specific pre-stretching techniques and initial tension values needed to meet requirements. A new method can accurately measure the tension of the Kevlar cord using a guitar tuner, because more conventional methods do not apply to arimid cords such as Kevlar.

A cyclotron isotope production facility designed to maximize production and minimize radiation dose

International Nuclear Information System (INIS)

Dickie, W.J.; Stevenson, N.R.; Szlavik, F.F.

1993-01-01

Continuing increases in requirements from the nuclear medicine industry for cyclotron isotopes is increasing the demands being put on an aging stock of machines. In addition, with the 1990 recommendations of the ICRP publication in place, strict dose limits will be required and this will have an effect on the way these machines are being operated. Recent advances in cyclotron design combined with lessons learned from two decades of commercial production mean that new facilities can result in a substantial charge on target, low personnel dose, and minimal residual activation. An optimal facility would utilize a well engineered variable energy/high current H - cyclotron design, multiple beam extraction, and individual target caves. Materials would be selected to minimize activation and absorb neutrons. Equipment would be designed to minimize maintenance activities performed in high radiation fields. (orig.)

Entropy Minimization Design Approach of Supersonic Internal Passages

Directory of Open Access Journals (Sweden)

Jorge Sousa

2015-08-01

Full Text Available Fluid machinery operating in the supersonic regime unveil avenues towards more compact technology. However, internal supersonic flows are associated with high aerodynamic and thermal penalties, which usually prevent their practical implementation. Indeed, both shock losses and the limited operational range represent particular challenges to aerodynamic designers that should be taken into account at the initial phase of the design process. This paper presents a design methodology for supersonic passages based on direct evaluations of the velocity field using the method of characteristics and computation of entropy generation across shock waves. This meshless function evaluation tool is then coupled to an optimization scheme, based on evolutionary algorithms that minimize the entropy generation across the supersonic passage. Finally, we assessed the results with 3D Reynolds Averaged Navier Stokes calculations.

Application of quality function deployment to the design of a lithium battery

Science.gov (United States)

Halbleib, L.; Wormington, P.; Cieslak, W.; Street, H.

Quality Function Deployment (QFD) is the tool we have selected to aid in the design, development and subsequent commercial manufacture of a Lithium/Thionyl Chloride 'D' cell for use in weapons applications. QFD is a structured methodology used to help assure that customer needs and expectations will be satisfied throughout the product life cycle. In this paper, we will describe our application of QFD, some of the lessons learned, and what we expect to be the final product of this QFD exercise.

A Systematic Procedure for the Generation of Cost-Minimized Designs

DEFF Research Database (Denmark)

Becker, Peter W.; Jarkler, Bjorn

1972-01-01

We present a procedure for the generation of cost-minimized designs of circuits and systems. Suppose a designer has decided upon the topology of his product. Also suppose he knows the cost and quality of the different grades of the N components required to implement the product. The designer...... then faces the following problem: How should he proceed to find the combination of grades that will give him the desired manufacturing yield at minimum product cost? We discuss the problem and suggest a policy by which the designer, with a reasonable computational effort, can find a set of ``good...

Vibration characteristics of a deployable controllable-geometry truss boom

Science.gov (United States)

Dorsey, J. T.

1983-01-01

An analytical study was made to evaluate changes in the fundamental frequency of a two dimensional cantilevered truss boom at various stages of deployment. The truss could be axially deployed or retracted and undergo a variety of controlled geometry changes by shortening or lengthening the telescoping diagonal members in each bay. Both untapered and tapered versions of the truss boom were modeled and analyzed by using the finite element method. Large reductions in fundamental frequency occurred for both the untapered and tapered trusses when they were uniformly retracted or maneuvered laterally from their fully deployed position. These frequency reductions can be minimized, however, if truss geometries are selected which maintain cantilever root stiffness during truss maneuvers.

Time Deployment Study for Annulus Pumping

International Nuclear Information System (INIS)

REBERGER, D.W.

2000-01-01

Radioactive wastes from processing irradiated uranium fuels have been stored as alkaline slurries in underground tanks at the Hanford Site. Single-shell tanks (SST) and double-shell tanks (DST) of various sizes were used for waste storage. Of the total 177 tanks, there are 28 DSTs. DSTs are located in AN, AP, AW, AY, AZ, and SY tank farms in the 200 East (200E) and 200-West (200W) Areas. The storage capacities of the DSTs vary from 980,000 to 1,140,000 gal. DSTs are designed and constructed as an integral steel structure, i.e., an inner shell within an outer shell, so that any leak from the inner shell is confined within the annulus without impacting the environment. The inner shell provides primary containment for the wastes and the outer shell provides secondary containment in the form of an annulus. The annulus of a DST is equipped with a pump pit, leak detection probes, and other accessories. The existing annulus pumps in the DSTs need to be revamped with a new system to reduce operating costs and reduce the time to deploy a pumping system. The new pumping system will minimize the likelihood of a release of waste into the environment; improve capability of waste removal to the maximum extent possible to comply with Washington Administrative Code (WAC) 173-303-640 and Code of Federal Regulations (CFR) 40 CFR 265.193. This study addresses the time required to deploy an annulus pumping system designed to fit any DST after detection of a leak in the inner shell of the DST

Intricacies of Using Kevlar Cord and Thermal Knives in a Deployable Release System: Issues and Solutions

Science.gov (United States)

Stewart, Alphonso; Hair, Jason H.

2002-01-01

The utilization of Kevlar cord and thermal knives in a deployable release system produces a number of issues that must be addressed in the design of the system. This paper proposes design considerations that minimize the major issues, thermal knife failure, Kevlar cord relaxation, and the measurement of the cord tension. Design practices can minimize the potential for thermal knife laminate and element damage that result in failure of the knife. A process for in-situ inspection of the knife with resistance, rather than continuity, checks and 10x zoom optical imaging can detect damaged knives. Tests allow the characterization of the behavior of the particular Kevlar cord in use and the development of specific prestretching techniques and initial tension values needed to meet requirements. A new method can accurately measure the tension of the Kevlar cord using a guitar tuner, because more conventional methods do not apply to arimid cords such as Kevlar.

The Design and Implementation of a Novel Open Source Massive Deployment System

Directory of Open Access Journals (Sweden)

Steven J. H. Shiau

2018-06-01

Full Text Available The hypervisor and container are emerging cloud computing and fog computing technologies, which enable rapid system deployment. However, both of the technologies depend on the operating system (OS and applications that are installed on the host machines. System deployment is the activity to deliver and install OSs and applications onto computers. Such deployment activities are widely required in the infrastructure of cloud computing, fog computing, high-performance computing clusters, and classrooms of computer education. Albeit the concept of system deployment is not new, traditional solutions cannot support the rapid evolution of open source file systems. Furthermore, existing solutions cannot support the massive deployment of disks in a computer as well as the massive deployment in large-scale computers. To resolve the issue, the authors proposed novel system architecture as well as software that is openly available. The experiments are undertaken by deploying a Linux system to 1 to 30 Universal Serial Bus (USB flash drives in a single machine and to 1 to 32 machines in a network using the software that is being developed in this work. The results have demonstrated the feasibility and efficiency of the proposed work. The relationships between the bus bandwidth, the writing rate of the USB flash drive, and the number of flash drives were also formulated as a govern equation. Performance evaluation and cost savings in comparing to the deployment cases adopting commercial software were also provided for demonstrating the performance enhancement and cost reduction by using the novel deployment system. In general, the proposed architecture and the developed software are highly effective from the aspects of both performance and cost.

A Remotely Deployable Wind Sonic Anemometer

Directory of Open Access Journals (Sweden)

Muhammad Awais

2017-12-01

Full Text Available Communication and computing shape up base for explosion of Internet of Things (IoT era. Humans can efficiently control the devices around their environment as per requirements because of IoT, the communication between different devices brings more flexibility in surrounding. Useful data is also gathered from some of these devices to create Big Data; where, further analysis assist in making life easier by developing good business models corresponding to user needs, enhance scientific research, formulating weather prediction or monitoring systems and contributing in other relative fields as well. Thus, in this research a remotely deployable IoT enabled Wind Sonic Anemometer has been designed and deployed to calculate average wind speed, direction, and gust. The proposed design is remotely deployable, user-friendly, power efficient and cost-effective because of opted modules i.e., ultrasonic sensors, GSM module, and solar panel. The testbed was also deployed at the roof of Computer & Information Systems Engineering (CIS department, NED UET. Further, its calibration has been carried out by using long short-term memory (LSTM, a deep learning technique; where ground truth data has been gathered from mechanical wind speed sensor (NRG-40 H deployed at top of Industrial & Manufacturing (IM department of NED UET. The obtained results are satisfactory and the performance of designed sensor is also good under various weather conditions.

An innovative deployable solar panel system for Cubesats

Science.gov (United States)

Santoni, Fabio; Piergentili, Fabrizio; Donati, Serena; Perelli, Massimo; Negri, Andrea; Marino, Michele

2014-02-01

One of the main Cubesat bus limitations is the available on-board power. The maximum power obtained using body mounted solar panels and advanced triple junction solar cells on a triple unit Cubesat is typically less than 10 W. The Cubesat performance and the mission scenario opened to these small satellite systems could be greatly enhanced by an increase of the available power. This paper describes the design and realization of a modular deployable solar panel system for Cubesats, consisting of a modular hinge and spring system that can be potentially used on-board single (1U), double(2U), triple (3U) and six units (6U) Cubesats. The size of each solar panels is the size of a lateral Cubesat surface. The system developed is the basis for a SADA (Solar Array Drive Assembly), in which a maneuvering capability is added to the deployed solar array in order to follow the apparent motion of the sun. The system design trade-off is discussed, comparing different deployment concepts and architectures, leading to the final selection for the modular design. A prototype of the system has been realized for a 3U Cubesat, consisting of two deployable solar panel systems, made of three solar panels each, for a total of six deployed solar panels. The deployment system is based on a plastic fiber wire and thermal cutters, guaranteeing a suitable level of reliability. A test-bed for the solar panel deployment testing has been developed, supporting the solar array during deployment reproducing the dynamical situation in orbit. The results of the deployment system testing are discussed, including the design and realization of the test-bed, the mechanical stress given to the solar cells by the deployment accelerations and the overall system performance. The maximum power delivered by the system is about 50.4 W BOL, greatly enhancing the present Cubesat solar array performance.

Planning soil tillage using quality function deployment (QFD

Directory of Open Access Journals (Sweden)

Milan Marcos

2003-01-01

Full Text Available The Brazilian forest sector represents about 4% of gross domestic product (GDP which is correspondent to US$ 21.0 billion. The natural forest area is approximately 4.8 million hectares and for the near future there will be a need to increase the planted area. To avoid or minimize the impact of mechanized practices on forest soils, the reduced tillage has been developed. The aim of this work is to define the technical priorities of the reduced tillage for eucalyptus seedlings, using quality function deployment (QDF. The design requirements classified as the most important to attend seedling demands were the furrow width and depth, and clod sizes. QFD has the potential to be applied to agro-forestry systems to translate plant demands into technical requirements.

Perceptions of Individual and Family Functioning Among Deployed Female National Guard Members.

Science.gov (United States)

Kelly, Patricia J; Cheng, An-Lin; Berkel, LaVerne A; Nilsson, Johanna

2016-08-01

Females currently make up 15% of U.S. military service members. Minimal attention has been paid to families of female National Guard members who have been deployed and their subsequent reintegration challenges. This cross-sectional Internet-based survey of female members of four National Guard units compared those who were and were not deployed. Instruments, guided by the variables of the Family Resilience Model, measured individual, family, and deployment-related factors. Bivariate analysis and ordinal logistic regression were done to assess differences between the groups. Of the 239 National Guard members surveyed, deployed women (n = 164) had significantly higher levels of posttraumatic stress disorder (PTSD; p family functioning were higher among deployed when compared with never deployed women. Results indicate community interventions that focus on strengthening coping skills of female Guard members would be useful for this population. © The Author(s) 2016.

Rapid deployment intrusion detection system

International Nuclear Information System (INIS)

Graham, R.H.

1997-01-01

A rapidly deployable security system is one that provides intrusion detection, assessment, communications, and annunciation capabilities; is easy to install and configure; can be rapidly deployed, and is reusable. A rapidly deployable intrusion detection system (RADIDS) has many potential applications within the DOE Complex: back-up protection for failed zones in a perimeter intrusion detection and assessment system, intrusion detection and assessment capabilities in temporary locations, protection of assets during Complex reconfiguration, and protection in hazardous locations, protection of assets during Complex reconfiguration, and protection in hazardous locations. Many DOE user-need documents have indicated an interest in a rapidly deployable intrusion detection system. The purpose of the RADIDS project is to design, develop, and implement such a system. 2 figs

DRAGON - 8U Nanosatellite Orbital Deployer

Science.gov (United States)

Dobrowolski, Marcin; Grygorczuk, Jerzy; Kedziora, Bartosz; Tokarz, Marta; Borys, Maciej

2014-01-01

The Space Research Centre of the Polish Academy of Sciences (SRC PAS) together with Astronika company have developed an Orbital Deployer called DRAGON for ejection of the Polish scientific nanosatellite BRITE-PL Heweliusz (Fig. 1). The device has three unique mechanisms including an adopted and scaled lock and release mechanism from the ESA Rosetta mission MUPUS instrument. This paper discusses major design restrictions of the deployer, unique design features, and lessons learned from development through testing.

Rover deployment system for lunar landing mission

Science.gov (United States)

Sutoh, Masataku; Hoshino, Takeshi; Wakabayashi, Sachiko

2017-09-01

For lunar surface exploration, a deployment system is necessary to allow a rover to leave the lander. The system should be as lightweight as possible and stored retracted when launched. In this paper, two types of retractable deployment systems for lunar landing missions, telescopic- and fold-type ramps, are discussed. In the telescopic-type system, a ramp is stored with the sections overlapping and slides out during deployment. In the fold-type system, it is stored folded and unfolds for the deployment. For the development of these ramps, a design concept study and structural analysis were conducted first. Subsequently, ramp deployment and rover release tests were performed using the developed ramp prototypes. Through these tests, the validity of their design concepts and functions have been confirmed. In the rover release test, it was observed that the developed lightweight ramp was sufficiently strong for a 50-kg rover to descend. This result suggests that this ramp system is suitable for the deployment of a 300-kg-class rover on the Moon, where the gravity is about one-sixth that on Earth. The lightweight and sturdy ramp developed in this study will contribute to both safe rover deployment and increase of lander/rover payload.

Advanced Deployable Structural Systems for Small Satellites

Science.gov (United States)

Belvin, W. Keith; Straubel, Marco; Wilkie, W. Keats; Zander, Martin E.; Fernandez, Juan M.; Hillebrandt, Martin F.

2016-01-01

One of the key challenges for small satellites is packaging and reliable deployment of structural booms and arrays used for power, communication, and scientific instruments. The lack of reliable and efficient boom and membrane deployment concepts for small satellites is addressed in this work through a collaborative project between NASA and DLR. The paper provides a state of the art overview on existing spacecraft deployable appendages, the special requirements for small satellites, and initial concepts for deployable booms and arrays needed for various small satellite applications. The goal is to enhance deployable boom predictability and ground testability, develop designs that are tolerant of manufacturing imperfections, and incorporate simple and reliable deployment systems.

Optimal Assignment of Cells in C-RAN Deployments with Multiple BBU Pools

DEFF Research Database (Denmark)

Holm, Henrik; Checko, Aleksandra; Al-obaidi, Rami

2015-01-01

Cloud Radio Access Network (C-RAN) is receiving increasing attention not only within the research community but also from operators and standardization bodies. However, even a good technology will be deployed only if it is economically viable. In our previous work, for larger scale deployment we...... recommend to divide the area into multiple BBU Pools. In this paper we show how to optimally assign cells to different BBU Pools in such a scenario. By using Integer Linear Programming (ILP) method we derive engineering guidelines for minimizing the CAPital EXpenditure (CAPEX) of C-RAN deployment....

Re-design of apple pia packaging using quality function deployment method

Science.gov (United States)

Pulungan, M. H.; Nadira, N.; Dewi, I. A.

2018-03-01

This study was aimed to identify the attributes for premium apple pia packaging, to determine the technical response to be carried out by Permata Agro Mandiri Small and Medium Enterprise (SME) and to design a new apple pie packaging acceptable by the SME. The Quality Function Deployment (QFD) method was employed to improve the apple pia packaging design, which consisted of seven stages in data analysis. The results indicated that whats attribute required by the costumers include graphic design, dimensions, capacity, shape, strength, and resistance of packaging. While, the technical responses to be conducted by the SMEs were as follows: attractive visual packaging designs, attractive colors, clear images and information, packaging size dimensions, a larger capacity packaging (more product content), ergonomic premium packaging, not easily torn, and impact resistant packaging materials. The findings further confirmed that the design of premium apple pia packaging accepted by the SMES was the one with the capacity of ten apple pia or 200 g weight, and with rectangular or beam shape form. The packaging material used was a duplex carton with 400 grammage (g/m2), the outer part of the packaging was coated with plastic and the inside was added with duplex carton. The acceptable packaging dimension was 30 cm x 5 cm x 3 cm (L x W x H) with a mix of black and yellow color in the graphical design.

Minimalism

CERN Document Server

Obendorf, Hartmut

2009-01-01

The notion of Minimalism is proposed as a theoretical tool supporting a more differentiated understanding of reduction and thus forms a standpoint that allows definition of aspects of simplicity. This book traces the development of minimalism, defines the four types of minimalism in interaction design, and looks at how to apply it.

Advanced OS deployment system

OpenAIRE

Galiano Molina, Sebastián

2007-01-01

The main project’s objective is to design and build an OS deployment system taking advantage of the Linux OS and the Open Source community developments. This means to use existing technologies that modularize the system. With this philosophy in mind, the number of developed code lines within the project is keeping as small as possible. As REMBO, the OS deployment system to develop has to be transparent to the user. This means a system with a friendly user interface and no te...

Design and initial deployment of the wireless local area networking infrastructure at Sandia National Laboratories.

Energy Technology Data Exchange (ETDEWEB)

Long, John P.; Hamill, Michael J.; Mitchell, M. G.; Miller, Marc M.; Witzke, Edward L.; Wiener, Dallas J

2006-11-01

A major portion of the Wireless Networking Project at Sandia National Laboratories over the last few years has been to examine IEEE 802.11 wireless networking for possible use at Sandia and if practical, introduce this technology. This project team deployed 802.11a, b, and g Wireless Local Area Networking at Sandia. This report examines the basics of wireless networking and captures key results from project tests and experiments. It also records project members thoughts and designs on wireless LAN architecture and security issues. It documents some of the actions and milestones of this project, including pilot and production deployment of wireless networking equipment, and captures the team's rationale behind some of the decisions made. Finally, the report examines lessons learned, future directions, and conclusions.

Verification Test for Ultra-Light Deployment Mechanism for Sectioned Deployable Antenna Reflectors

Science.gov (United States)

Zajac, Kai; Schmidt, Tilo; Schiller, Marko; Seifart, Klaus; Schmalbach, Matthias; Scolamiero, Lucio

2013-09-01

The ultra-light deployment mechanism (UDM) is based on three carbon fibre reinforced plastics (CFRP) curved tape springs made of carbon fibre / cyanate ester prepregs.In the frame of the activity its space application suitability for the deployment of solid reflector antenna sections was investigated. A projected diameter of the full reflector of 4 m to 7 m and specific mass in the order of magnitude of 2.6kg/m2 was focused for requirement derivation.Extensive verification tests including health checks, environmental and functional tests were carried out with an engineering model to enable representative characterizing of the UDM unit.This paper presents the design and a technical description of the UDM as well as a summary of achieved development status with respect to test results and possible design improvements.

Shape memory alloy fracture as a deployment actuator

International Nuclear Information System (INIS)

Buban, Darrick M; Frantziskonis, George N

2013-01-01

The paper reports an experimental investigation into using shape memory alloy (SMA) as a deployment actuator. SMA specimens were heated and pulled to failure or pulled and heated to failure, thus developing an environmental and structural operating envelope for application as deployment mechanisms. The experimental results strongly suggest that SMAs can be implemented as deployment actuators. Recorded data shows that SMA fracture is possible over a wide range of temperatures and strains, filling a material performance gap not found in the literature. The obtained information allows design engineers to appropriately size SMAs given the design requirements for achieving the desired deployment effects. The major conclusion of the reported work is that SMAs as actuators are strong competitors to typical existing deployment efforts that use explosive or non-explosive actuators having implementation drawbacks such as the expense associated with special handling and the volume encountered in mounting the devices. (paper)

Fast Deploy Radiation Monitoring Array Emergency Solution Based on GPS and Cellular Network

International Nuclear Information System (INIS)

Vax, E.; Broide, A.; Manor, A.; Marcus, E.; Seif, R.; Nir, J.; Kadmon, Y.; Sattinger, D.; Levinson, S.; Tal, N.

2004-01-01

Radiation monitoring of a possible contaminating source is highly important for safety and risk analysis. Since the monitoring must cover the whole contaminated area, the standard solution is to scatter an array of numerous fixed detectors in advance. The Fast Deploy Radiation Monitoring Array (FDRMA) is a solution that does not require coverage of the entire area. The FDRMA is a compact, world wide applicative, seamless and novel solution, designed for emergency cases. The system consists of GPS and IP cellular network, which make it mobile and therefore suitable for global use. The most significant advantage of the FDRMA system is minimizing the exposure time of the monitoring teams, while maintaining flexibility of the deployment area, as opposed to the Vehicle Monitoring System (VMS) [1] or the standard solution mentioned above. A detailed description of the proposed FDRMA system and its comparison to a fixed detectors' array is presented in this work

Optimal experiment design for quantum state tomography: Fair, precise, and minimal tomography

International Nuclear Information System (INIS)

Nunn, J.; Smith, B. J.; Puentes, G.; Walmsley, I. A.; Lundeen, J. S.

2010-01-01

Given an experimental setup and a fixed number of measurements, how should one take data to optimally reconstruct the state of a quantum system? The problem of optimal experiment design (OED) for quantum state tomography was first broached by Kosut et al.[R. Kosut, I. Walmsley, and H. Rabitz, e-print arXiv:quant-ph/0411093 (2004)]. Here we provide efficient numerical algorithms for finding the optimal design, and analytic results for the case of 'minimal tomography'. We also introduce the average OED, which is independent of the state to be reconstructed, and the optimal design for tomography (ODT), which minimizes tomographic bias. Monte Carlo simulations confirm the utility of our results for qubits. Finally, we adapt our approach to deal with constrained techniques such as maximum-likelihood estimation. We find that these are less amenable to optimization than cruder reconstruction methods, such as linear inversion.

Swarm Deployable Boom Assembly (DBA) Development of a Deployable Magnetometer Boom for the Swarm Spacecraft

Science.gov (United States)

McMahon, Paul; Jung, Hans-Juergen; Edwards, Jeff

2013-09-01

The Swarm programme consists of 3 magnetically clean satellites flying in close formation designed to measure the Earth's magnetic field using 2 Magnetometers mounted on a 4.3m long deployable boom.Deployment is initiated by releasing 3 HDRMs, once released the boom oscillates back and forth on a pair of pivots, similar to a restaurant kitchen door hinge, for around 120 seconds before coming to rest on 3 kinematic mounts which are used to provide an accurate reference location in the deployed position. Motion of the boom is damped through a combination of friction, spring hysteresis and flexing of the 120+ cables crossing the hinge. Considerable development work and accurate numerical modelling of the hinge motion was required to predict performance across a wide temperature range and ensure that during the 1st overshoot the boom did not damage itself, the harness or the spacecraft.Due to the magnetic cleanliness requirements of the spacecraft no magnetic materials could be used in the design of the hardware.

Lightweight landscape enhancing design through minimal mass structures

CERN Document Server

Spinelli, Luigi; Monticelli, Carol; Pedrali, Paolo

2016-01-01

This book explains how lightweight materials and structures can be deployed in buildings to meet high environmental and aesthetic standards and emphasizes how the concept of lightness in building technology and design dovetails with the desire to enhance landscape. The first part of the book, on lightweight construction, aims to foster the use of membranes within the specific climatic context and in particular considers how lightweight materials and innovative technologies can enrich the quality of temporary spaces. The second part focuses exclusively on landscape, presenting novel approaches in the search for visual lightness and the quest to improve urban spaces. Particular attention is paid to the Italian experience, where the traditional appreciation of brick and stone has limited the scope for use of lightweight structures and membrane materials, often relegating them to a secondary or inappropriate role. The reader will come to appreciate how this attitude demeans a very advanced productive sector and n...

Design and Analysis of Cost-Efficient Sensor Deployment for Tracking Small UAS with Agent-Based Modeling.

Science.gov (United States)

Shin, Sangmi; Park, Seongha; Kim, Yongho; Matson, Eric T

2016-04-22

Recently, commercial unmanned aerial systems (UAS) have gained popularity. However, these UAS are potential threats to people in terms of safety in public places, such as public parks or stadiums. To reduce such threats, we consider a design, modeling, and evaluation of a cost-efficient sensor system that detects and tracks small UAS. In this research, we focus on discovering the best sensor deployments by simulating different types and numbers of sensors in a designated area, which provide reasonable detection rates at low costs. Also, the system should cover the crowded areas more thoroughly than vacant areas to reduce direct threats to people underneath. This research study utilized the Agent-Based Modeling (ABM) technique to model a system consisting of independent and heterogeneous agents that interact with each other. Our previous work presented the ability to apply ABM to analyze the sensor configurations with two types of radars in terms of cost-efficiency. The results from the ABM simulation provide a list of candidate configurations and deployments that can be referred to for applications in the real world environment.

Design and Analysis of Cost-Efficient Sensor Deployment for Tracking Small UAS with Agent-Based Modeling

Directory of Open Access Journals (Sweden)

Sangmi Shin

2016-04-01

Full Text Available Recently, commercial unmanned aerial systems (UAS have gained popularity. However, these UAS are potential threats to people in terms of safety in public places, such as public parks or stadiums. To reduce such threats, we consider a design, modeling, and evaluation of a cost-efficient sensor system that detects and tracks small UAS. In this research, we focus on discovering the best sensor deployments by simulating different types and numbers of sensors in a designated area, which provide reasonable detection rates at low costs. Also, the system should cover the crowded areas more thoroughly than vacant areas to reduce direct threats to people underneath. This research study utilized the Agent-Based Modeling (ABM technique to model a system consisting of independent and heterogeneous agents that interact with each other. Our previous work presented the ability to apply ABM to analyze the sensor configurations with two types of radars in terms of cost-efficiency. The results from the ABM simulation provide a list of candidate configurations and deployments that can be referred to for applications in the real world environment.

Design of a deployment rotation mechanism for microsatellite

NARCIS (Netherlands)

Abdelal, G.F.; Bakr Elhady, A.; Kassab, M.

2009-01-01

Solar array rotation mechanism provides a hinged joint between the solar panel and satellite body, smooth rotation of the solar array into deployed position and its fixation in this position. After unlocking of solar panel (while in orbit), rotation bracket turns towards ready-to-work position under

MULTI-SENSOR NETWORK FOR LANDSLIDES SIMULATION AND HAZARD MONITORING - DESIGN AND DEPLOYMENT

Directory of Open Access Journals (Sweden)

H. Wu

2012-08-01

Full Text Available This paper describes a newly developed multi-sensor network system for landslide and hazard monitoring. Landslide hazard is one of the most destructive natural disasters, which has severely affected human safety, properties and infrastructures. We report the results of designing and deploying the multi-sensor network, based on the simulated landslide model, to monitor typical landslide areas and with a goal to predict landslide hazard and mitigate damages. The integration and deployment of the prototype sensor network were carried out in an experiment area at Tongji University in Shanghai. In order to simulate a real landslide, a contractible landslide body is constructed in the experiment area by 7m*1.5m. Then, some different kind of sensors, such as camera, GPS, crackmeter, accelerometer, laser scanning system, inclinometer, etc., are installed near or in the landslide body. After the sensors are powered, continuous sampling data will be generated. With the help of communication method, such as GPRS, and certain transport devices, such as iMesh and 3G router, all the sensor data will be transported to the server and stored in Oracle. These are the current results of an ongoing project of the center. Further research results will be updated and presented in the near future.

Advanced nuclear power plant design with minimized use of cables

International Nuclear Information System (INIS)

Anon.

1984-01-01

The objective of this report is to present a nuclear power plant design with a minimum utilization of cables. The report describes the types of software and hardware that will be needed to minimize hard-wired control and instrumentation circuits and to reduce the quantity of low voltage power cables while maintaining a high availability and reliability of the plant control systems

Eco-design of low energy mechanical milling through implementation of quality function deployment and design for sustainability

Science.gov (United States)

Rashid, Muhammad Hanif Abd; Nor, Nik Hisyamudin Muhd; Selamat, Siti Norhana; Hassan, Mohd Fahrul; Rahim, Abd Khalil Abd; Ahmad, Mohd Fauzi; Ismail, Al Emran; Omar, Badrul; Mokhtar, Mohd Faiz; Turan, Faiz Mohd; Yokoyama, Seiji

2017-04-01

Malaysia as a developing country favor energy demand by years which created mainly from fossil fuel. Unfortunately, the action leads to significant increment in carbon dioxide (CO2) emission that causing the global warming. The most promising mitigation strategy is by deploying Carbon Capture and Storage (CCS) technology where mineral carbonation was identified as the safest method for permanent storage and does not require continuous monitoring. Accordingly, National Green Technology was launched in 2009 to support the growth of green technology development in Malaysia as a carbon mitigation strategy. Thus, this paper aims to propose the development of a conceptual eco-design for Low Energy Mechanical Milling (LEMM). The concept was proposed by using the Quality Function Deployment (QFD) tool with combination of sustainability determinants (DFS) namely economic, environmental and social which evaluated using Solidworks 2015 sustainability assessment. The results show the new product targets for LEMM in prior on energy consumption (MJ), selling price (MYR), material cost (MYR), carbon footprint (kg CO2) with weightage of 5.2, 4.2, 3.6 and 3.6 respectively. The implementation of DFS criteria into the QFD promote to reduce material used by 16%, 35% reduction of carbon footprint, 28% less energy consumption, 28% lower air acidification, 77% of water eutrophication declined and increased recyclability by 15%.

Development and Deployment of Systems-Based Approaches for the Management of Soilborne Plant Pathogens.

Science.gov (United States)

Chellemi, D O; Gamliel, A; Katan, J; Subbarao, K V

2016-03-01

Biological suppression of soilborne diseases with minimal use of outside interventive actions has been difficult to achieve in high input conventional crop production systems due to the inherent risk of pest resurgence. This review examines previous approaches to the management of soilborne disease as precursors to the evolution of a systems-based approach, in which plant disease suppression through natural biological feedback mechanisms in soil is incorporated into the design and operation of cropping systems. Two case studies are provided as examples in which a systems-based approach is being developed and deployed in the production of high value crops: lettuce/strawberry production in the coastal valleys of central California (United States) and sweet basil and other herb crop production in Israel. Considerations for developing and deploying system-based approaches are discussed and operational frameworks and metrics to guide their development are presented with the goal of offering a credible alternative to conventional approaches to soilborne disease management.

Structural analysis of ITER multi-purpose deployer

International Nuclear Information System (INIS)

Manuelraj, Manoah Stephen; Dutta, Pramit; Gotewal, Krishan Kumar; Rastogi, Naveen; Tesini, Alessandro; Choi, Chang-Hwan

2016-01-01

Highlights: • System modelling for structural analysis of the Multi-Purpose Deployer (MPD). • Finite element modeling of the Multi-Purpose Deployer (MPD). • Static, modal and seismic response analysis of the Multi-Purpose Deployer (MPD). • Iterative structural analysis and design update to satisfy the structural criteria. • Modal analysis for various kinematic configurations. • Reaction force calculations on the interfacing systems. - Abstract: The Multi-Purpose Deployer (MPD) is a general purpose ITER in-vessel remote handling (RH) system. The main handling equipment, known as the MPD Transporter, consists of a series of linked bodies, which provide anchoring to the vacuum vessel port and an articulated multi-degree of freedom motion to perform various in-vessel maintenance tasks. During the in-vessel operations, the structural integrity of the system should be guaranteed against various operational and seismic loads. This paper presents the structural analysis results of the concept design of the MPD Transporter considering the seismic events. Static structural, modal and frequency response spectrum analyses have been performed to verify the structural integrity of the system, and to provide reaction forces to the interfacing systems such as vacuum vessel and cask. Iterative analyses and design updates are carried out based on the reference design of the system to improve the structural behavior of the system. The frequency responses of the system in various kinematics and payloads are assessed.

Very Low Head Turbine Deployment in Canada

International Nuclear Information System (INIS)

Kemp, P; Williams, C; Sasseville, Remi; Anderson, N

2014-01-01

The Very Low Head (VLH) turbine is a recent turbine technology developed in Europe for low head sites in the 1.4 - 4.2 m range. The VLH turbine is primarily targeted for installation at existing hydraulic structures to provide a low impact, low cost, yet highly efficient solution. Over 35 VLH turbines have been successfully installed in Europe and the first VLH deployment for North America is underway at Wasdell Falls in Ontario, Canada. Deployment opportunities abound in Canada with an estimated 80,000 existing structures within North America for possible low-head hydro development. There are several new considerations and challenges for the deployment of the VLH turbine technology in Canada in adapting to the hydraulic, environmental, electrical and social requirements. Several studies were completed to determine suitable approaches and design modifications to mitigate risk and confirm turbine performance. Diverse types of existing weirs and spillways pose certain hydraulic design challenges. Physical and numerical modelling of the VLH deployment alternatives provided for performance optimization. For this application, studies characterizing the influence of upstream obstacles using water tunnel model testing as well as full-scale prototype flow dynamics testing were completed. A Cold Climate Adaptation Package (CCA) was developed to allow year-round turbine operation in ice covered rivers. The CCA package facilitates turbine extraction and accommodates ice forces, frazil ice, ad-freezing and cold temperatures that are not present at the European sites. The Permanent Magnet Generator (PMG) presents some unique challenges in meeting Canadian utility interconnection requirements. Specific attention to the frequency driver control and protection requirements resulted in a driver design with greater over-voltage capability for the PMG as well as other key attributes. Environmental studies in Europe included fish friendliness testing comprised of multiple in

Very Low Head Turbine Deployment in Canada

Science.gov (United States)

Kemp, P.; Williams, C.; Sasseville, Remi; Anderson, N.

2014-03-01

The Very Low Head (VLH) turbine is a recent turbine technology developed in Europe for low head sites in the 1.4 - 4.2 m range. The VLH turbine is primarily targeted for installation at existing hydraulic structures to provide a low impact, low cost, yet highly efficient solution. Over 35 VLH turbines have been successfully installed in Europe and the first VLH deployment for North America is underway at Wasdell Falls in Ontario, Canada. Deployment opportunities abound in Canada with an estimated 80,000 existing structures within North America for possible low-head hydro development. There are several new considerations and challenges for the deployment of the VLH turbine technology in Canada in adapting to the hydraulic, environmental, electrical and social requirements. Several studies were completed to determine suitable approaches and design modifications to mitigate risk and confirm turbine performance. Diverse types of existing weirs and spillways pose certain hydraulic design challenges. Physical and numerical modelling of the VLH deployment alternatives provided for performance optimization. For this application, studies characterizing the influence of upstream obstacles using water tunnel model testing as well as full-scale prototype flow dynamics testing were completed. A Cold Climate Adaptation Package (CCA) was developed to allow year-round turbine operation in ice covered rivers. The CCA package facilitates turbine extraction and accommodates ice forces, frazil ice, ad-freezing and cold temperatures that are not present at the European sites. The Permanent Magnet Generator (PMG) presents some unique challenges in meeting Canadian utility interconnection requirements. Specific attention to the frequency driver control and protection requirements resulted in a driver design with greater over-voltage capability for the PMG as well as other key attributes. Environmental studies in Europe included fish friendliness testing comprised of multiple in

A highly articulated robotic surgical system for minimally invasive surgery.

Science.gov (United States)

Ota, Takeyoshi; Degani, Amir; Schwartzman, David; Zubiate, Brett; McGarvey, Jeremy; Choset, Howie; Zenati, Marco A

2009-04-01

We developed a novel, highly articulated robotic surgical system (CardioARM) to enable minimally invasive intrapericardial therapeutic delivery through a subxiphoid approach. We performed preliminary proof of concept studies in a porcine preparation by performing epicardial ablation. CardioARM is a robotic surgical system having an articulated design to provide unlimited but controllable flexibility. The CardioARM consists of serially connected, rigid cyclindrical links housing flexible working ports through which catheter-based tools for therapy and imaging can be advanced. The CardioARM is controlled by a computer-driven, user interface, which is operated outside the operative field. In six experimental subjects, the CardioARM was introduced percutaneously through a subxiphoid access. A commercial 5-French radiofrequency ablation catheter was introduced through the working port, which was then used to guide deployment. In all subjects, regional ("linear") left atrial ablation was successfully achieved without complications. Based on these preliminary studies, we believe that the CardioARM promises to enable deployment of a number of epicardium-based therapies. Improvements in imaging techniques will likely facilitate increasingly complex procedures.

Conceptual design of EAST multi-purpose maintenance deployer system

International Nuclear Information System (INIS)

Pan, Hongtao; He, Kaihui; Cheng, Yong; Song, Yuntao; Yang, Yang; Villedieu, Eric; Shi, Shanshuang; Yang, Songzhu

2017-01-01

Highlights: • A redundant 11-DOF articulated robot for EAST in-vessel maintenance is presented. • A new modular joint developed to optimize the yaw joint actuator for the robot is described. • A 3-DOF gripper integrated with cameras and torque sensor is developed. - Abstract: EAST multi-purpose maintenance deployer (EMMD) system, being collaboratively developed by ASIPP and CEA-IRFM, is built as upgrades for EAMA. Updated kinematics parameters such as DOF distribution and joint angle for EMMD robot are performed and verified in a simulation platform. A new modular joint has been developed to optimize the yaw joint actuator for easy assembly and flexibility reduction. A 3-DOF gripper with cameras and torque sensor has been designed to provide inspection and dexterous handling of small fragments inside the EAST chamber. A conceptual upgrade for EAMA-CASK has been developed for the purpose of protecting the end-effector's sensors which do not have temperature-resistant qualification. The high temperature and vacuum compatible solutions and validation experiments have been presented in this paper.

Conceptual design of EAST multi-purpose maintenance deployer system

Energy Technology Data Exchange (ETDEWEB)

Pan, Hongtao [Institute of Plasma Physics, Chinese Academy of Sciences, 350 Shushanhu Rd, Hefei, Anhui (China); University of Science and Technology of China, Hefei, Anhui 230022 (China); He, Kaihui, E-mail: hekh@iterchina.cn [China International Nuclear Fusion Energy Program Execution Center, Beijing 100862 (China); Cheng, Yong [Institute of Plasma Physics, Chinese Academy of Sciences, 350 Shushanhu Rd, Hefei, Anhui (China); Song, Yuntao [Institute of Plasma Physics, Chinese Academy of Sciences, 350 Shushanhu Rd, Hefei, Anhui (China); University of Science and Technology of China, Hefei, Anhui 230022 (China); Yang, Yang [Institute of Plasma Physics, Chinese Academy of Sciences, 350 Shushanhu Rd, Hefei, Anhui (China); Villedieu, Eric [CEA-IRFM, F-13108 Saint-Paul-Lez-Durance (France); Shi, Shanshuang; Yang, Songzhu [Institute of Plasma Physics, Chinese Academy of Sciences, 350 Shushanhu Rd, Hefei, Anhui (China)

2017-05-15

Highlights: • A redundant 11-DOF articulated robot for EAST in-vessel maintenance is presented. • A new modular joint developed to optimize the yaw joint actuator for the robot is described. • A 3-DOF gripper integrated with cameras and torque sensor is developed. - Abstract: EAST multi-purpose maintenance deployer (EMMD) system, being collaboratively developed by ASIPP and CEA-IRFM, is built as upgrades for EAMA. Updated kinematics parameters such as DOF distribution and joint angle for EMMD robot are performed and verified in a simulation platform. A new modular joint has been developed to optimize the yaw joint actuator for easy assembly and flexibility reduction. A 3-DOF gripper with cameras and torque sensor has been designed to provide inspection and dexterous handling of small fragments inside the EAST chamber. A conceptual upgrade for EAMA-CASK has been developed for the purpose of protecting the end-effector's sensors which do not have temperature-resistant qualification. The high temperature and vacuum compatible solutions and validation experiments have been presented in this paper.

Packaging, deployment, and panel design concepts for a truss-stiffened 7-panel precision deployable reflector with feed boom

Science.gov (United States)

Heard, Walter L., Jr.; Collins, Timothy J.; Dyess, James W.; Kenner, Scott; Bush, Harold G.

1993-01-01

A concept is presented for achieving a remotely deployable truss-stiffened reflector consisting of seven integrated sandwich panels that form the reflective surface, and an integrated feed boom. The concept has potential for meeting aperture size and surface precision requirements for some high-frequency microwave remote sensing applications. The packaged reflector/feed boom configuration is a self-contained unit that can be conveniently attached to a spacecraft bus. The package has a cylindrical envelope compatible with typical launch vehicle shrouds. Dynamic behavior of a deployed configuration having a 216-inch focal length and consisting of 80-inch-diameter, two-inch-thick panels is examined through finite-element analysis. Results show that the feed boom and spacecraft bus can have a large impact on the fundamental frequency of the deployed configuration. Two candidate rib-stiffened sandwich panel configurations for this application are described, and analytical results for panel mass and stiffness are presented. Results show that the addition of only a few rib stiffeners, if sufficiently deep, can efficiently improve sandwich panel stiffness.

Algorithmic PON/P2P FTTH Access Network Design for CAPEX Minimization

DEFF Research Database (Denmark)

Papaefthimiou, Kostantinos; Tefera, Yonas; Mihylov, Dimitar

2013-01-01

one. It provides an obvious advantage for the end users in terms of high achievable data rates. On the other hand, the high initial deployment cost required exists as the heaviest impediment. The main goal of this paper is to study different approaches when designing a fiber access network. More......Due to the emergence of high bandwidth-requiring services, telecommunication operators (telcos) are called to upgrade their fixed access network. In order to keep up with the competition, they must consider different optical access network solutions with Fiber To The Home (FTTH) as the prevailing...

Integrating Kano’s Model into Quality Function Deployment for Product Design: A Comprehensive Review

Science.gov (United States)

Ginting, Rosnani; Hidayati, Juliza; Siregar, Ikhsan

2018-03-01

Many methods and techniques are adopted by some companies to improve the competitiveness through the fulfillment of customer satisfaction by enhancement and improvement the product design quality. Over the past few years, several researcher have studied extensively combining Quality Function Deployment and Kano’s model as design techniques by focusing on translating consumer desires into a product design. This paper presents a review and analysis of several literatures that associated to the integration methodology of Kano into the QFD process. Various of international journal articles were selected, collected and analyzed through a number of relevant scientific publications. In-depth analysis was performed, and focused in this paper on the results, advantages and drawbacks of its methodology. In addition, this paper also provides the analysis that acquired in this study related to the development of the methodology. It is hopedd this paper can be a reference for other researchers and manufacturing companies to implement the integration method of QFD- Kano for product design.

A Tabu Search WSN Deployment Method for Monitoring Geographically Irregular Distributed Events

Directory of Open Access Journals (Sweden)

2009-03-01

Full Text Available In this paper, we address the Wireless Sensor Network (WSN deployment issue. We assume that the observed area is characterized by the geographical irregularity of the sensed events. Formally, we consider that each point in the deployment area is associated a differentiated detection probability threshold, which must be satisfied by our deployment method. Our resulting WSN deployment problem is formulated as a Multi-Objectives Optimization problem, which seeks to reduce the gap between the generated events detection probabilities and the required thresholds while minimizing the number of deployed sensors. To overcome the computational complexity of an exact resolution, we propose an original pseudo-random approach based on the Tabu Search heuristic. Simulations show that our proposal achieves better performances than several other approaches proposed in the literature. In the last part of this paper, we generalize the deployment problem by including the wireless communication network connectivity constraint. Thus, we extend our proposal to ensure that the resulting WSN topology is connected even if a sensor communication range takes small values.

A Tabu Search WSN Deployment Method for Monitoring Geographically Irregular Distributed Events.

Science.gov (United States)

Aitsaadi, Nadjib; Achir, Nadjib; Boussetta, Khaled; Pujolle, Guy

2009-01-01

In this paper, we address the Wireless Sensor Network (WSN) deployment issue. We assume that the observed area is characterized by the geographical irregularity of the sensed events. Formally, we consider that each point in the deployment area is associated a differentiated detection probability threshold, which must be satisfied by our deployment method. Our resulting WSN deployment problem is formulated as a Multi-Objectives Optimization problem, which seeks to reduce the gap between the generated events detection probabilities and the required thresholds while minimizing the number of deployed sensors. To overcome the computational complexity of an exact resolution, we propose an original pseudo-random approach based on the Tabu Search heuristic. Simulations show that our proposal achieves better performances than several other approaches proposed in the literature. In the last part of this paper, we generalize the deployment problem by including the wireless communication network connectivity constraint. Thus, we extend our proposal to ensure that the resulting WSN topology is connected even if a sensor communication range takes small values.

Shape accuracy optimization for cable-rib tension deployable antenna structure with tensioned cables

Science.gov (United States)

Liu, Ruiwei; Guo, Hongwei; Liu, Rongqiang; Wang, Hongxiang; Tang, Dewei; Song, Xiaoke

2017-11-01

Shape accuracy is of substantial importance in deployable structures as the demand for large-scale deployable structures in various fields, especially in aerospace engineering, increases. The main purpose of this paper is to present a shape accuracy optimization method to find the optimal pretensions for the desired shape of cable-rib tension deployable antenna structure with tensioned cables. First, an analysis model of the deployable structure is established by using finite element method. In this model, geometrical nonlinearity is considered for the cable element and beam element. Flexible deformations of the deployable structure under the action of cable network and tensioned cables are subsequently analyzed separately. Moreover, the influence of pretension of tensioned cables on natural frequencies is studied. Based on the results, a genetic algorithm is used to find a set of reasonable pretension and thus minimize structural deformation under the first natural frequency constraint. Finally, numerical simulations are presented to analyze the deployable structure under two kinds of constraints. Results show that the shape accuracy and natural frequencies of deployable structure can be effectively improved by pretension optimization.

Kinematic design considerations for minimally invasive surgical robots: an overview.

Science.gov (United States)

Kuo, Chin-Hsing; Dai, Jian S; Dasgupta, Prokar

2012-06-01

Kinematic design is a predominant phase in the design of robotic manipulators for minimally invasive surgery (MIS). However, an extensive overview of the kinematic design issues for MIS robots is not yet available to both mechanisms and robotics communities. Hundreds of archival reports and articles on robotic systems for MIS are reviewed and studied. In particular, the kinematic design considerations and mechanism development described in the literature for existing robots are focused on. The general kinematic design goals, design requirements, and design preferences for MIS robots are defined. An MIS-specialized mechanism, namely the remote center-of-motion (RCM) mechanism, is revisited and studied. Accordingly, based on the RCM mechanism types, a classification for MIS robots is provided. A comparison between eight different RCM types is given. Finally, several open challenges for the kinematic design of MIS robotic manipulators are discussed. This work provides a detailed survey of the kinematic design of MIS robots, addresses the research opportunity in MIS robots for kinematicians, and clarifies the kinematic point of view to MIS robots as a reference for the medical community. Copyright © 2012 John Wiley & Sons, Ltd.

Optimization of Hydroacoustic Equipment Deployment at Foster Dam, 2013

Energy Technology Data Exchange (ETDEWEB)

Hughes, James S.; Johnson, Gary E.; Ploskey, Gene R.; Hennen, Matthew J.; Fischer, Eric S.; Zimmerman, Shon A.

2013-03-01

The goal of the study was to optimize performance of the fixed-location hydroacoustic systems at Foster Dam (FOS) by determining deployment and data acquisition methods that minimized structural, electrical, and acoustic interference. Optimization of the hydroacoustic systems will establish methodology for sampling by active acoustic methods during this year-long evaluation of juvenile salmonid passage at FOS.

An easy to deploy street light control system based on wireless communication and LED technology.

Science.gov (United States)

Elejoste, Pilar; Angulo, Ignacio; Perallos, Asier; Chertudi, Aitor; Zuazola, Ignacio Julio García; Moreno, Asier; Azpilicueta, Leire; Astrain, José Javier; Falcone, Francisco; Villadangos, Jesús

2013-05-16

This paper presents an intelligent streetlight management system based on LED lamps, designed to facilitate its deployment in existing facilities. The proposed approach, which is based on wireless communication technologies, will minimize the cost of investment of traditional wired systems, which always need civil engineering for burying of cable underground and consequently are more expensive than if the connection of the different nodes is made over the air. The deployed solution will be aware of their surrounding's environmental conditions, a fact that will be approached for the system intelligence in order to learn, and later, apply dynamic rules. The knowledge of real time illumination needs, in terms of instant use of the street in which it is installed, will also feed our system, with the objective of providing tangible solutions to reduce energy consumption according to the contextual needs, an exact calculation of energy consumption and reliable mechanisms for preventive maintenance of facilities.

An Easy to Deploy Street Light Control System Based on Wireless Communication and LED Technology

Directory of Open Access Journals (Sweden)

Jesús Villadangos

2013-05-01

Full Text Available This paper presents an intelligent streetlight management system based on LED lamps, designed to facilitate its deployment in existing facilities. The proposed approach, which is based on wireless communication technologies, will minimize the cost of investment of traditional wired systems, which always need civil engineering for burying of cable underground and consequently are more expensive than if the connection of the different nodes is made over the air. The deployed solution will be aware of their surrounding’s environmental conditions, a fact that will be approached for the system intelligence in order to learn, and later, apply dynamic rules. The knowledge of real time illumination needs, in terms of instant use of the street in which it is installed, will also feed our system, with the objective of providing tangible solutions to reduce energy consumption according to the contextual needs, an exact calculation of energy consumption and reliable mechanisms for preventive maintenance of facilities.

Stochastic Optimization for Nuclear Facility Deployment Scenarios

Science.gov (United States)

Hays, Ross Daniel

to eventual disposal. By varying the specifications of the deployment scenario, the simulated annealing algorithm will seek to either minimize the value of a single objective function, or enumerate the trade-off surface between multiple competing objective functions. The available objective functions represent key stakeholder values, minimizing such important factors as high-level waste disposal burden, required uranium ore supply, relative proliferation potential, and economic cost and uncertainty. The optimization program itself is designed to be modular, allowing for continued expansion and exploration as research needs and curiosity indicate. The utility and functionality of this optimization program are demonstrated through its application to one potential fuel cycle scenario of interest. In this scenario, an existing legacy LWR fleet is assumed at the year 2000. The electric power demand grows exponentially at a rate of 1.8% per year through the year 2100. Initially, new demand is met by the construction of 1-GW(e) LWRs. However, beginning in the year 2040, 600-MW(e) sodium-cooled, fast-spectrum reactors operating in a transuranic burning regime with full recycling of spent fuel become available to meet demand. By varying the fraction of new capacity allocated to each reactor type, the optimization program is able to explicitly show the relationships that exist between uranium utilization, long-term heat for geologic disposal, and cost-of-electricity objective functions. The trends associated with these trade-off surfaces tend to confirm many common expectations about the use of nuclear power, namely that while overall it is quite insensitive to variations in the cost of uranium ore, it is quite sensitive to changes in the capital costs of facilities. The optimization algorithm has shown itself to be robust and extensible, with possible extensions to many further fuel cycle optimization problems of interest.

Accommodating Thickness in Origami-Based Deployable Arrays

Science.gov (United States)

Zirbel, Shannon A.; Magleby, Spencer P.; Howell, Larry L.; Lang, Robert J.; Thomson, Mark W.; Sigel, Deborah A.; Walkemeyer, Phillip E.; Trease, Brian P.

2013-01-01

The purpose of this work is to create deployment systems with a large ratio of stowed-to-deployed diameter. Deployment from a compact form to a final flat state can be achieved through origami-inspired folding of panels. There are many models capable of this motion when folded in a material with negligible thickness; however, when the application requires the folding of thick, rigid panels, attention must be paid to the effect of material thickness not only on the final folded state, but also during the folding motion (i.e., the panels must not be required to flex to attain the final folded form). The objective is to develop new methods for deployment from a compact folded form to a large circular array (or other final form). This paper describes a mathematical model for modifying the pattern to accommodate material thickness in the context of the design, modeling, and testing of a deployable system inspired by an origami six-sided flasher model. The model is demonstrated in hardware as a 1/20th scale prototype of a deployable solar array for space applications. The resulting prototype has a ratio of stowed-to-deployed diameter of 9.2 (or 1.25 m deployed outer diameter to 0.136 m stowed outer diameter).

The medical software quality deployment method.

Science.gov (United States)

Hallberg, N; Timpka, T; Eriksson, H

1999-03-01

The objective of this study was to develop a Quality Function Deployment (QFD) model for design of information systems in health-care environments. Consecutive blocked-subject case studies were conducted, based on action research methods. Starting with a QFD model for software development, a model for information system design, the Medical Software Quality Deployment (MSQD) model, was developed. The MSQD model was divided into the pre-study phase, in which the customer categories and their power to influence the design are determined; the data collection phase, in which the voice of customers (VoC) is identified by observations and interviews and quantified by Critical. Incident questionnaires; the need specification phase, where the VoC is specified into ranked customer needs; and the design phase where the customer needs are transformed stepwise to technical requirements and design attributes. QFD showed to be useful for integrating the values of different customer categories in software development for health-care settings. In the later design phases, other quality methods should be used for software implementation and testing.

Development and modeling of self-deployable structures

Science.gov (United States)

Neogi, Depankar

Deployable space structures are prefabricated structures which can be transformed from a closed, compact configuration to a predetermined expanded form in which they are stable and can bear loads. The present research effort investigates a new family of deployable structures, called the Self-Deployable Structures (SDS). Unlike other deployable structures, which have rigid members, the SDS members are flexible while the connecting joints are rigid. The joints store the predefined geometry of the deployed structure in the collapsed state. The SDS is stress-free in both deployed and collapsed configurations and results in a self-standing structure which acquires its structural properties after a chemical reaction. Reliability of deployment is one of the most important features of the SDS, since it does not rely on mechanisms that can lock during deployment. The unit building block of these structures is the self-deployable structural element (SDSE). Several SDSE members can be linked to generate a complex building block such as a triangular or a tetrahedral structure. Different SDSE and SDS concepts are investigated in the research work, and the performance of SDS's are experimentally and theoretically explored. Triangular and tetrahedral prototype SDS have been developed and presented. Theoretical efforts include modeling the behavior of 2-dimensional SDSs. Using this design tool, engineers can study the effects of different packing configurations and deployment sequence; and perform optimization on the collapsed state of a structure with different external constraints. The model also predicts if any lockup or entanglement occurs during deployment.

Using Deduplicating Storage for Efficient Disk Image Deployment

Directory of Open Access Journals (Sweden)

Xing Lin

2015-08-01

Full Text Available Many clouds and network testbeds use disk images to initialize local storage on their compute devices. Large facilities must manage thousands or more images, requiring significant amounts of storage. At the same time, to provide a good user experience, they must be able to deploy those images quickly. Driven by our experience in operating the Emulab site at the University of Utah---a long-lived and heavily-used testbed---we have created a new service for efficiently storing and deploying disk images. This service exploits the redundant data found in similar images, using deduplication to greatly reduce the amount of physical storage required. In addition to space savings, our system is also designed for highly efficient image deployment---it integrates with an existing highly-optimized disk image deployment system, Frisbee, without significantly increasing the time required to distribute and install images. In this paper, we explain the design of our system and discuss the trade-offs we made to strike a balance between efficient storage and fast disk image deployment. We also propose a new chunking algorithm, called AFC, which enables fixed-size chunking for deduplicating allocated disk sectors. Experimental results show that our system reduces storage requirements by up to 3x while imposing only a negligible runtime overhead on the end-to-end disk-deployment process.

Features of the Calculation Deployment Large Transformable Structures of Different Configurations

Directory of Open Access Journals (Sweden)

V. N. Zimin

2014-01-01

Full Text Available Despite the significant progress achieved in the design of space transformable structures to ensure a smooth and reliable deployment remains an important task. This type of construction can consist of dozens, hundreds or even thousands of interconnected elements. Deployment transformable space structures in orbit to test their performance in orbital conditions are associated with high material costs. Full deploy: experimental development process transformable structures involve a number of fundamental difficulties: It is impossible to eliminate the influence of gravity and resistance forces conditions. Thus, to calculate deploy of large transformable structures of various configurations is an important stage of their creation. Simulation provides an opportunity to analyze various schemes of deploy, to reveal their advantages and possible disadvantages. For numerical analysis of deploy of such structures is necessary to use modern software modeling of the dynamics of multi-component of mechanical systems such as EULER and Adams. Simulation of deployment space transformable structures was performed taking as example folding flat antenna contours diameter of 5 m and 20 m, foldable spatial calibration reflector diameter of 3 m, deployable antenna reflector truss-type aperture 3×6 m.The results of the calculations represent following characteristics: the time of adoption of the working position structures; form intermediate positions structures during deployment; dependence of opening angles and angular velocities of the design links on the time. The parameters of these calculations can be used as input in the development of structural elements providing deployment. They can also be used to prepare stands for experimental testing of disclosure designs in ground conditions. It should be noted that the theoretical models are the only way to analyze the deployment of such structures for possible emergency situations.

Connected Vehicle Pilot Deployment Program phase 1 : comprehensive deployment plan : New York City : volume 1 : technical application : part I : technical and management approach.

Science.gov (United States)

2016-08-01

This document describes the Deployment Plan for the New York City Department of Transportation (NYC) Connected Vehicle Pilot Deployment (CVPD) Project. This plan describes the approach to complete Phase 2 Design/Build/Test, and Phase 3 Operate and Ma...

The ATLAS EventIndex: architecture, design choices, deployment and first operation experience

CERN Document Server

Barberis, Dario; The ATLAS collaboration; Cranshaw, Jack; Favareto, Andrea; Fernandez Casani, Alvaro; Gallas, Elizabeth; Glasman, Claudia; Gonzalez de la Hoz, Santiago; Hrivnac, Julius; Malon, David; Prokoshin, Fedor; Salt, José; Sánchez, Javier; Toebbicke, Rainer; Yuan, Ruijun

2015-01-01

The EventIndex is the complete catalogue of all ATLAS events, keeping the references to all files that contain a given event in any processing stage. It replaces the TAG database, which had been in use during LHC Run 1. For each event it contains its identifiers, the trigger pattern and the GUIDs of the files containing it. Major use cases are event picking, feeding the Event Service used on some production sites, and technical checks of the completion and consistency of processing campaigns. The system design is highly modular so that its components (data collection system, storage system based on Hadoop, query web service and interfaces to other ATLAS systems) could be developed separately and in parallel during LS1. The EventIndex is in operation for the start of LHC Run 2. This paper describes the high-level system architecture, the technical design choices and the deployment process and issues. The performance of the data collection and storage systems, as well as the query services, are also reported.

The ATLAS EventIndex: architecture, design choices, deployment and first operation experience

CERN Document Server

Barberis, Dario; The ATLAS collaboration; Cranshaw, Jack; Favareto, Andrea; Fernandez Casani, Alvaro; Gallas, Elizabeth; Glasman, Claudia; Gonzalez de la Hoz, Santiago; Hrivnac, Julius; Malon, David; Prokoshin, Fedor; Salt, José; Sánchez, Javier; Rainer Toebbicke; Yuan, Ruijun

2015-01-01

The EventIndex is the complete catalogue of all ATLAS events, keeping the references to all files that contain a given event in any processing stage. It replaces the TAG database, which had been in use during LHC Run 1. For each event it contains its identifiers, the trigger pattern and the GUIDs of the files containing it. Major use cases are event picking, feeding the Event Service used on some production sites, and technical checks of the completion and consistency of processing campaigns. The system design is highly modular so that its components (data collection system, storage system based on Hadoop, query web service and interfaces to other ATLAS systems) could be developed separately and in parallel during LS1. The EventIndex is in operation for the start of LHC Run 2. This talk describes the high level system architecture, the technical design choices and the deployment process and issues. The performance of the data collection and storage systems, as well as the query services, will be reported.

The ATLAS EventIndex: architecture, design choices, deployment and first operation experience

Science.gov (United States)

Barberis, D.; Cárdenas Zárate, S. E.; Cranshaw, J.; Favareto, A.; Fernández Casaní, Á.; Gallas, E. J.; Glasman, C.; González de la Hoz, S.; Hřivnáč, J.; Malon, D.; Prokoshin, F.; Salt Cairols, J.; Sánchez, J.; Többicke, R.; Yuan, R.

2015-12-01

The EventIndex is the complete catalogue of all ATLAS events, keeping the references to all files that contain a given event in any processing stage. It replaces the TAG database, which had been in use during LHC Run 1. For each event it contains its identifiers, the trigger pattern and the GUIDs of the files containing it. Major use cases are event picking, feeding the Event Service used on some production sites, and technical checks of the completion and consistency of processing campaigns. The system design is highly modular so that its components (data collection system, storage system based on Hadoop, query web service and interfaces to other ATLAS systems) could be developed separately and in parallel during LSI. The EventIndex is in operation for the start of LHC Run 2. This paper describes the high-level system architecture, the technical design choices and the deployment process and issues. The performance of the data collection and storage systems, as well as the query services, are also reported.

Neutral beam deployment on DEMO and its influence on design

Energy Technology Data Exchange (ETDEWEB)

Surrey, Elizabeth, E-mail: elizabeth.surrey@ccfe.ac.uk [EURATOM/CCFE, Culham Science Centre, Abingdon, Oxfordshire, OX14 3DB (United Kingdom); King, Damian; Lister, Jonathan; Porton, Michael; Timmis, William; Ward, David [EURATOM/CCFE, Culham Science Centre, Abingdon, Oxfordshire, OX14 3DB (United Kingdom)

2011-10-15

The demands on the neutral beam heating and current drive system of a DEMO device exceed those of existing fusion experiments by several orders of magnitude. By predicting possible power waveforms it is possible to analyse the technological advances necessary to achieve a system relevant to deployment on a power plant. Achieving the necessary efficiency will require simultaneous improvements in beam current density, neutralization efficiency and beam transmission. Considering the deployment on the tokamak vessel shows no major disruption to the tritium breeder blanket and no requirement to reach a high packing density of injectors. The thermal management of components subjected to low heat flux for many hours is considered and it is shown that radiation cooling can be exploited to control the temperature of such items.

Design of a piezoelectric inchworm actuator and compliant end effector for minimally invasive surgery

Science.gov (United States)

Canfield, Shawn; Edinger, Ben; Frecker, Mary I.; Koopmann, Gary H.

1999-06-01

Recent advances in robotics, tele-robotics, smart material actuators, and mechatronics raise new possibilities for innovative developments in millimeter-scale robotics capable of manipulating objects only fractions of a millimeter in size. These advances can have a wide range of applications in the biomedical community. A potential application of this technology is in minimally invasive surgery (MIS). The focus of this paper is the development of a single degree of freedom prototype to demonstrate the viability of smart materials, force feedback and compliant mechanisms for minimally invasive surgery. The prototype is a compliant gripper that is 7-mm by 17-mm, made from a single piece of titanium that is designed to function as a needle driver for small scale suturing. A custom designed piezoelectric `inchworm' actuator drives the gripper. The integrated system is computer controlled providing a user interface device capable of force feedback. The design methodology described draws from recent advances in three emerging fields in engineering: design of innovative tools for MIS, design of compliant mechanisms, and design of smart materials and actuators. The focus of this paper is on the design of a millimeter-scale inchworm actuator for use with a compliant end effector in MIS.

'Post-deployment appraisal' and the relationship with stress and psychological health in Australian veterans.

Science.gov (United States)

Wright, Breanna; Forbes, Andrew; Kelsall, Helen; Clarke, David; Ikin, Jill; Sim, Malcolm

2015-12-01

Understanding how veterans appraise their post-deployment experiences could provide insight into better assisting their deployment transitions. We aimed to assess the factor structure of positive and negative post-deployment appraisals in Australian veterans and to examine the resultant factors in their relationship with military stress and psychological health. Questions capturing post-deployment attitudes were developed by the researchers in collaboration with veterans. The questions were administered to 1938 veterans and the results factor analysed. The relationships between post-deployment appraisal, military stress and psychological health were examined using Structural Equation Modelling. A three-factor solution was found for the post-deployment appraisal questions; representing personal development, lack of recognition, and appreciation of life and country. Military stress was associated with the three factors and psychological health. The three factors were weakly to moderately associated with psychological health. Mediation between military stress and psychological health by any post-deployment appraisal factor was minimal. Post-deployment appraisal measures three important attitudes and concerns of veterans after deployment. Military stress is associated with the post-deployment appraisal factors. However, the factors did not mediate the relationship between military stress and psychological health. These factors provide insight into how veterans appraise their complex array of post-deployment experiences, and may provide useful in regard to transitions and integration into civilian life.

A SDP based design of relay precoding for the power minimization of MIMO AF-relay networks

KAUST Repository

Rao, Anlei

2015-09-11

Relay precoding for multiple-input and multiple-output (MIMO) relay networks has been approached by either optimizing the efficiency performance with given power consumption constraints or minimizing the power consumption with quality-of-service (QoS) requirements. For the later type design, previous works has worked on minimizing the approximated power consumption. In this paper, exact power consumption for all relays is derived into a quadratic form by diagonalizing the minimum-square error (MSE) matrix, and the relay precoding matrix is designed by optimizing this quadratic form with the help of semidefinite programming (SDP) relaxation. Our simulation results show that such a design can achieve a gain of around 3 dB against the previous design, which optimized the approximated power consumption. © 2015 IEEE.

RadNet Air Quality (Deployable) Data

Data.gov (United States)

U.S. Environmental Protection Agency — RadNet Deployable Monitoring is designed to collect radiological and meteorological information and data asset needed to establish the impact of radiation levels on...

Photovoltaic deployment strategy in Japan and the USA-an institutional appraisal

International Nuclear Information System (INIS)

Shum, Kwok L.; Watanabe, Chihiro

2007-01-01

Photovoltaic (PV) is a renewable energy technology, along side with other modular energy generation technologies such as micro-turbines, fuel cells, etc., which will enable the alternative distributed generation paradigm compared to the incumbent fossil fuel based centralized generation paradigm. Distributed generation utilizing renewable energy resources offers opportunities for significant carbon dioxide and emissions reductions thus contributing solutions to broader climate change issues. Yet, renewable energy technologies like PV face various barriers for their widespread adoption. Aside from technical and cost issues, renewable technologies have to overcome the so-called carbon lock-in effects. This refers to the techno-institutional complex associated with the fossil-fuel based centralized generation regime that currently dominates energy production and use. Governmental interventions to address these issues usually can be seen as composed of research, development, demonstration and deployment or RD3 [PCAST, 1999. Panel on International Cooperation in Energy Research, Development, Demonstration, and Deployment]. This paper focused on comparing the deployment aspect of PV technology in Japan and the USA. While both governments promoted PV as part of their larger strategies to address various environmental and energy security issues, Japan has built a PV installation capacity three times that of the USA as of December 2003 with over 90% of PV installation in the grid-connected small residential system category. This is in marked contrast to the case in the USA in which the cumulative installation is spilt among different types of applications involving the grid and off the grid. We put forward two models to explain these differences in deployment strategies and their possible consequences. The first deployment model leverages upon PV as a manufactured technology with minimal customization to achieve massive deployment. The second deployment model leverages upon

Design optimization of transformerless grid-connected PV inverters including reliability

DEFF Research Database (Denmark)

Koutroulis, Eftichios; Blaabjerg, Frede

2012-01-01

Of the Electricity (LCOE) generated during the PV system lifetime period is minimized. The LCOE is calculated also considering the failure rates of the components, which affect the reliability performance and lifetime maintenance cost of the PV inverter. A design example is presented, demonstrating that compared...... to the non-optimized PV inverter structures, the PV inverters designed using the proposed optimization methodology exhibit lower total manufacturing and lifetime maintenance cost and inject more energy into the electric-grid and by that minimizing LCOE.......This paper presents a new methodology for optimal design of transformerless Photovoltaic (PV) inverters targeting a cost-effective deployment of grid-connected PV systems. The optimal values and types of the PV inverter components are calculated such that the PV inverter Levelized Cost...

Design Optimization of Transformerless Grid-Connected PV Inverters Including Reliability

DEFF Research Database (Denmark)

Koutroulis, Eftichios; Blaabjerg, Frede

2013-01-01

such that the PV inverter LCOE generated during the PV system lifetime period is minimized. The LCOE is also calculated considering the failure rates of the components, which affect the reliability performance and lifetime maintenance cost of the PV inverter. A design example is presented, demonstrating...... that compared to the nonoptimized PV inverter structures, the PV inverters designed using the proposed optimization methodology exhibit lower total manufacturing and lifetime maintenance cost and inject more energy into the electric-grid and by that minimizing LCOE.......This paper presents a new methodology for optimal design of transformerless photovoltaic (PV) inverters targeting a cost-effective deployment of grid-connected PV systems. The optimal switching frequency as well as the optimal values and types of the PV inverter components is calculated...

Cloud Environment Automation: from infrastructure deployment to application monitoring

Science.gov (United States)

Aiftimiei, C.; Costantini, A.; Bucchi, R.; Italiano, A.; Michelotto, D.; Panella, M.; Pergolesi, M.; Saletta, M.; Traldi, S.; Vistoli, C.; Zizzi, G.; Salomoni, D.

2017-10-01

The potential offered by the cloud paradigm is often limited by technical issues, rules and regulations. In particular, the activities related to the design and deployment of the Infrastructure as a Service (IaaS) cloud layer can be difficult to apply and time-consuming for the infrastructure maintainers. In this paper the research activity, carried out during the Open City Platform (OCP) research project [1], aimed at designing and developing an automatic tool for cloud-based IaaS deployment is presented. Open City Platform is an industrial research project funded by the Italian Ministry of University and Research (MIUR), started in 2014. It intends to research, develop and test new technological solutions open, interoperable and usable on-demand in the field of Cloud Computing, along with new sustainable organizational models that can be deployed for and adopted by the Public Administrations (PA). The presented work and the related outcomes are aimed at simplifying the deployment and maintenance of a complete IaaS cloud-based infrastructure.

Deployable structures for a human lunar base

Science.gov (United States)

Gruber, Petra; Häuplik, Sandra; Imhof, Barbara; Özdemir, Kürsad; Waclavicek, Rene; Perino, Maria Antoinetta

2007-06-01

The study Lunar exploration architecture—deployable structures for a lunar base was performed within the Alcatel Alenia Space “Lunar Exploration Architecture” study for the European Space Agency. The purpose of the study was to investigate bionic concepts applicable to deployable structures and to interpret the findings for possible implementation concepts. The study aimed at finding innovative solutions for deployment possibilities. Translating folding/unfolding principles from nature, candidate geometries were developed and researched using models, drawings and visualisations. The use of materials, joints between structural elements and construction details were investigated for these conceptual approaches. Reference scenarios were used to identify the technical and environmental conditions, which served as design drivers. Mechanical issues and the investigation of deployment processes narrowed the selection down to six chosen concepts. Their applicability was evaluated at a conceptual stage in relation to the timescale of the mission.

Gossamer-1: Mission concept and technology for a controlled deployment of gossamer spacecraft

Science.gov (United States)

Seefeldt, Patric; Spietz, Peter; Sproewitz, Tom; Grundmann, Jan Thimo; Hillebrandt, Martin; Hobbie, Catherin; Ruffer, Michael; Straubel, Marco; Tóth, Norbert; Zander, Martin

2017-01-01

Gossamer structures for innovative space applications, such as solar sails, require technology that allows their controlled and thereby safe deployment. Before employing such technology for a dedicated science mission, it is desirable, if not necessary, to demonstrate its reliability with a Technology Readiness Level (TRL) of six or higher. The aim of the work presented here is to provide reliable technology that enables the controlled deployment and verification of its functionality with various laboratory tests, thereby qualifying the hardware for a first demonstration in low Earth orbit (LEO). The development was made in the Gossamer-1 project of the German Aerospace Center (DLR). This paper provides an overview of the Gossamer-1 mission and hardware development. The system is designed based on the requirements of a technology demonstration mission. The design rests on a crossed boom configuration with triangular sail segments. Employing engineering models, all aspects of the deployment were tested under ambient environment. Several components were also subjected to environmental qualification testing. An innovative stowing and deployment strategy for a controlled deployment, as well as the designs of the bus system, mechanisms and electronics are described. The tests conducted provide insights into the deployment process and allow a mechanical characterization of that deployment process, in particular the measurement of the deployment forces. Deployment on system level could be successfully demonstrated to be robust and controllable. The deployment technology is on TRL four approaching level five, with a qualification model for environmental testing currently being built.

Industrial deployment of system engineering methods

CERN Document Server

Romanovsky, Alexander

2013-01-01

A formal method is not the main engine of a development process, its contribution is to improve system dependability by motivating formalisation where useful. This book summarizes the results of the DEPLOY research project on engineering methods for dependable systems through the industrial deployment of formal methods in software development. The applications considered were in automotive, aerospace, railway, and enterprise information systems, and microprocessor design.  The project introduced a formal method, Event-B, into several industrial organisations and built on the lessons learned to

Development of the Aquarius Antenna Deployment Mechanisms and Spring/Damper Actuator

Science.gov (United States)

Johnson, Joel A.

2008-01-01

The Aquarius Instrument s large radar reflector dish needed to be stowed for launch, and then deployed on-orbit. The Deployment Subsystem consisted of a cantilevered boom structure and two single-axis hinge mechanisms to accurately deploy and position the reflector dish relative to the radar feed horns. The cantilevered design demanded high stiffness and accuracy from the deployment mechanism at the root of the boom. A preload-generating end-of-travel latch was also required. To largely eliminate the need for control systems, each deployment mechanism was actuated by a passive spring motor with viscous-fluid damping. Tough requirements and adaptation of a heritage actuator to the new application resulted in numerous challenges. Fabrication, assembly, and testing encountered additional problems, though ultimately the system was demonstrated very successfully. This paper revisits the development to highlight which design concepts worked and the many important lessons learned.

Deployment Strategies and Clustering Protocols Efficiency

Directory of Open Access Journals (Sweden)

Chérif Diallo

2017-06-01

Full Text Available Wireless sensor networks face significant design challenges due to limited computing and storage capacities and, most importantly, dependence on limited battery power. Energy is a critical resource and is often an important issue to the deployment of sensor applications that claim to be omnipresent in the world of future. Thus optimizing the deployment of sensors becomes a major constraint in the design and implementation of a WSN in order to ensure better network operations. In wireless networking, clustering techniques add scalability, reduce the computation complexity of routing protocols, allow data aggregation and then enhance the network performance. The well-known MaxMin clustering algorithm was previously generalized, corrected and validated. Then, in a previous work we have improved MaxMin by proposing a Single- node Cluster Reduction (SNCR mechanism which eliminates single-node clusters and then improve energy efficiency. In this paper, we show that MaxMin, because of its original pathological case, does not support the grid deployment topology, which is frequently used in WSN architectures. The unreliability feature of the wireless links could have negative impacts on Link Quality Indicator (LQI based clustering protocols. So, in the second part of this paper we show how our distributed Link Quality based d- Clustering Protocol (LQI-DCP has good performance in both stable and high unreliable link environments. Finally, performance evaluation results also show that LQI-DCP fully supports the grid deployment topology and is more energy efficient than MaxMin.

Identifying and designing chemicals with minimal acute aquatic toxicity.

Science.gov (United States)

Kostal, Jakub; Voutchkova-Kostal, Adelina; Anastas, Paul T; Zimmerman, Julie Beth

2015-05-19

Industrial ecology has revolutionized our understanding of material stocks and flows in our economy and society. For this important discipline to have even deeper impact, we must understand the inherent nature of these materials in terms of human health and the environment. This paper focuses on methods to design synthetic chemicals to reduce their intrinsic ability to cause adverse consequence to the biosphere. Advances in the fields of computational chemistry and molecular toxicology in recent decades allow the development of predictive models that inform the design of molecules with reduced potential to be toxic to humans or the environment. The approach presented herein builds on the important work in quantitative structure-activity relationships by linking toxicological and chemical mechanistic insights to the identification of critical physical-chemical properties needed to be modified. This in silico approach yields design guidelines using boundary values for physiochemical properties. Acute aquatic toxicity serves as a model endpoint in this study. Defining value ranges for properties related to bioavailability and reactivity eliminates 99% of the chemicals in the highest concern for acute aquatic toxicity category. This approach and its future implementations are expected to yield very powerful tools for life cycle assessment practitioners and molecular designers that allow rapid assessment of multiple environmental and human health endpoints and inform modifications to minimize hazard.

Global Precipitation Measurement (GPM) and International Space Station (ISS) Coordination for CubeSat Deployments to Minimize Collision Risk

Science.gov (United States)

Pawloski, James H.; Aviles, Jorge; Myers, Ralph; Parris, Joshua; Corley, Bryan; Hehn, Garrett; Pascucci, Joseph

2016-01-01

The Global Precipitation Measurement Mission (GPM) is a joint U.S. and Japan mission to observe global precipitation, extending the Tropical Rainfall Measuring Mission (TRMM), which was launched by H-IIA from Tanegashima in Japan on February 28TH, 2014 directly into its 407km operational orbit. The International Space Station (ISS) is an international human research facility operated jointly by Russia and the USA from NASA's Johnson Space Center (JSC) in Houston Texas. Mission priorities lowered the operating altitude of ISS from 415km to 400km in early 2105, effectively placing both vehicles into the same orbital regime. The ISS has begun a program of deployments of cost effective CubeSats from the ISS that allow testing and validation of new technologies. With a major new asset flying at the same effective altitude as the ISS, CubeSat deployments became a serious threat to GPM and therefore a significant indirect threat to the ISS. This paper describes the specific problem of collision threat to GPM and risk to ISS CubeSat deployment and the process that was implemented to keep both missions safe from collision and maximize their project goals.

Deployment Methods for an Origami-Inspired Rigid-Foldable Array

Science.gov (United States)

Zirbel, Shannon A.; Trease, Brian P.; Magleby, Spencer P.; Howell, Larry L.

2014-01-01

The purpose of this work is to evaluate several deployment methods for an origami-inspired solar array at two size scales: 25-meter array and CubeSat array. The array enables rigid panel deployment and introduces new concepts for actuating CubeSat deployables. The design for the array was inspired by the origami flasher model (Lang, 1997; Shafer, 2001). Figure 1 shows the array prototyped from Garolite and Kapton film at the CubeSat scale. Prior work demonstrated that rigid panels like solar cells could successfully be folded into the final stowed configuration without requiring the panels to flex (Zirbel, Lang, Thomson, & al., 2013). The design of the array is novel and enables efficient use of space. The array can be wrapped around the central bus of the spacecraft in the case of the large array, or can accommodate storage of a small instrument payload in the case of the CubeSat array. The radial symmetry of this array around the spacecraft is ideally suited for spacecraft that need to spin. This work focuses on several actuation methods for a one-time deployment of the array. The array is launched in its stowed configuration and it will be deployed when it is in space. Concepts for both passive and active actuation were considered.

Deployable reflector configurations

Science.gov (United States)

Meinel, A. B.; Meinel, M. P.; Woolf, N. J.

Both the theoretical reasons for considering a non-circular format for the Large Deployable Reflector, and a potentially realizable concept for such a device, are discussed. The optimum systems for diffraction limited telescopes with incoherent detection have either a single filled aperture, or two such apertures as an interferometer to synthesize a larger aperture. For a single aperture of limited area, a reflector in the form of a slot can be used to give increased angular resolution. It is shown how a 20 x 8 meter telescope can be configured to fit the Space Shuttle bay, and deployed with relatively simple operations. The relationship between the sunshield design and the inclination of the orbit is discussed. The possible use of the LDR as a basic module to permit the construction of supergiant space telescopes and interferometers both for IR/submm studies and for the entire ultraviolet through mm wave spectral region is discussed.

Testing the Deployment Repeatability of a Precision Deployable Boom Prototype for the Proposed SWOT Karin Instrument

Science.gov (United States)

Agnes, Gregory S.; Waldman, Jeff; Hughes, Richard; Peterson, Lee D.

2015-01-01

NASA's proposed Surface Water Ocean Topography (SWOT) mission, scheduled to launch in 2020, would provide critical information about Earth's oceans, ocean circulation, fresh water storage, and river discharge. The mission concept calls for a dual-antenna Ka-band radar interferometer instrument, known as KaRIn, that would map the height of water globally along two 50 km wide swaths. The KaRIn antennas, which would be separated by 10 meters on either side of the spacecraft, would need to be precisely deployable in order to meet demanding pointing requirements. Consequently, an effort was undertaken to design build and prototype a precision deployable Mast for the KaRIn instrument. Each mast was 4.5-m long with a required dilitation stability of 2.5 microns over 3 minutes. It required a minimum first mode of 7 Hz. Deployment repeatability was less than +/- 7 arcsec in all three rotation directions. Overall mass could not exceed 41.5 Kg including any actuators and thermal blanketing. This set of requirements meant the boom had to be three times lighter and two orders of magnitude more precise than the existing state of the art for deployable booms.

Turbo-machine deployment of HTR-10 GT

International Nuclear Information System (INIS)

Zhu Shutang; Wang Jie; Zhang Zhengming; Yu Suyuan

2005-01-01

As a testing project of gas turbine modular High Temperature Gas-cooled Reactor (HTGR), HTR-10GT has been studied and developed by Institute of Nuclear and New Energy Technology (INET) of Tsinghua University after the success of HTR-10 with steam turbine cycle. The main purposes of this project are to demonstrate the gas turbine modular HTGR, to optimize the deployment of Power Conversion Unit (PCU) and to verify the techniques of turbo-machine, operating modes and controlling measures. HTR-10GT is concentrated on the PCU design and the turbo-machine deployment. Possible turbo-machine deployments have been investigated and two of them are introduced in this paper. The preliminary design for the turbo-machine of HTR-10GT is single-shaft of vertical layout, arranged by the side of the reactor and the turbo-compressor rotary speed was selected to be 250 s -1 (15000 r/min) by considering the efficiency of turbo-compressor blade systems, the strength conditions and the mass and size characteristics of the turbo-compressor. The rotor system will be supported by electromagnetic bearings (EMBs) to curb the possible pollutions of the primary loop. Of all the components in this design, the high speed turbo-generator seems to be a world-wide technical nut. As an alternative design, a gearbox complex is used to reduce the rotary speed from the turbo-compressor 250 s -1 to 50 s -1 so that the ordinary generator can be used. (authors)

IRIS. Progress in licensing and toward deployment

International Nuclear Information System (INIS)

Petrovic, B.; Carelli, M.D.; Kling, C.L.; Cavlina, N.; Grgic, D.

2006-01-01

The International Reactor Innovative and Secure (IRIS) is an advanced, integral, light water cooled, pressurized reactor of smaller generating capacity (1000 MWt, or 335 MWe). It is being developed through a strong international partnership by a team lead by Westinghouse and including organizations from 10 countries. The main objective of the project is to offer a simple nuclear power plant with outstanding safety, attractive economics and enhanced proliferation resistance characteristics ready for deployment within the next decade. IRIS embodies the requirements set forth by the recently announced US DOE Global Nuclear Energy Partnership (GNEP) program for worldwide deployment of a smaller-scale reactors and provides a viable bridge to Generation IV reactors. IRIS is designed to address the needs of both developed and emerging markets. Its smaller power level provides deployment flexibility in larger developed markets, and makes it in particular well suited for markets with limited grids or where the annual energy demand growth is moderate. Due to its short construction time and the staggered build option, IRIS significantly reduces the required financing, improves cash flow, and provides a viable solution for economies with limited resources. While based on proven and worldwide accepted LWR technology, IRIS introduces a number of innovative solutions to simplify its design and improve safety and operational characteristics, including the integral primary system and its components, as well as the safety-by-design approach. These features will be tested and demonstrated in a testing program that has been initiated. As its centerpiece, the program will include the integral test facility. Results of this program will support licensing with the US NRC. A multinational licensing is considered to facilitate worldwide deployment. (author)

Deployment Repeatability

Science.gov (United States)

2016-04-01

evaluating the deployment repeatability builds upon the testing or analysis of deployment kinematics (Chapter 6) and adds repetition. Introduction...material yield or failure during a test. For the purposes of this chapter, zero shift will refer to permanent changes in the structure, while reversible ...the content of other chapters in this book: Gravity Compensation (Chapter 4) and Deployment Kinematics and Dynamics (Chapter 6). Repeating the

Origami-inspired, on-demand deployable and collapsible mechanical metamaterials with tunable stiffness

Science.gov (United States)

Zhai, Zirui; Wang, Yong; Jiang, Hanqing

2018-03-01

Origami has been employed to build deployable mechanical metamaterials through folding and unfolding along the crease lines. Deployable metamaterials are usually flexible, particularly along their deploying and collapsing directions, which unfortunately in many cases leads to an unstable deployed state, i.e., small perturbations may collapse the structure along the same deployment path. Here we create an origami-inspired mechanical metamaterial with on-demand deployability and selective collapsibility through energy analysis. This metamaterial has autonomous deployability from the collapsed state and can be selectively collapsed along two different paths, embodying low stiffness for one path and substantially high stiffness for another path. The created mechanical metamaterial yields load-bearing capability in the deployed direction while possessing great deployability and collapsibility. The principle in this work can be utilized to design and create versatile origami-inspired mechanical metamaterials that can find many applications.

AP1000R licensing and deployment in the United States

International Nuclear Information System (INIS)

Jordan, R. P.; Russ, P. A.; Filiak, P. P.; Castiglione, L. L.

2012-01-01

In recent years, both domestic and foreign utilities have turned to the standardized Westinghouse AP1000 plant design in satisfying their near - and long-term - sustainable energy needs. As direct support to these actions, licensing the AP1000 design has played a significant role by providing one of the fundamental bases in clearing regulatory hurdles leading to the start of new plant construction. Within the U.S. alone, Westinghouse AP1000 licensing activities have reached unprecedented milestones with the approvals of both AP1000 Design Certification and Southern Company's combined construction permit and operating license (COL) application directly supporting the construction of two new nuclear plants in Georgia. Further COL application approvals are immediately pending for an additional two AP1000 plants in South Carolina. And, across the U.S. nuclear industry spectrum, there are 10 other COL applications under regulatory review representing some 16 new plants at 10 sites. In total, these actions represent the first wave of new plant licensing under the regulatory approval process since 1978. Fundamental to the Nuclear Regulatory Commission's AP1000 Design Certification is the formal recognition of the AP1000 passive safety design through regulatory acceptance rulemaking. Through recognition and deployment of the AP1000 Design Certification, the utility licensee / operator of this reactor design are now offered an opportunity to use a simplified 'one-step' combined license process, thereby managing substantial back-end construction schedule risk from regulatory and intervention delays. Application of this regulatory philosophy represents both acceptance and encouragement of standardized reactor designs like the AP1000. With the recent AP1000 Design Certification and utility COL acceptances, the fundamental licensing processes of this philosophy have successfully proven the attainment of significant milestones with the next stage licensing actions directed

Morphing structures using soft polymers for active deployment

International Nuclear Information System (INIS)

Daynes, Stephen; Grisdale, Amy; Trask, Richard; Seddon, Annela

2014-01-01

In this study, we take inspiration from morphing strategies observed in nature, origami design and stiffness tailoring principles in engineering, to develop a thin walled, low cost, bistable cell geometry capable of reversibly unfolding from a flat configuration to a highly textured configuration. Finite element analysis was used to model the cell deployment and capture the experimentally observed bistability of the reinforced silicone elastomer. Through the combination of flexible elastomers with locally reinforced regions enables a highly tailorable and controllable deployment response. These cells are bistable allowing them to maintain their shape when either deployed or retracted without sustained actuation. It is proposed that such deployable cells with reversible surfaces and texture change can be used as a means of adaptive camouflage. (fast track communication)

Accelerating the deployment of offshore renewable energy technologies. Final Report

Energy Technology Data Exchange (ETDEWEB)

MacDonald, Mott

2011-02-15

Offshore wind energy and ocean energy (i.e. wave and tidal) are at different stages of technology development and deployment, and, as such, they require different approaches for successful deployment. However, regardless of their deployment stage, these technologies may face common hurdles in their way to market competitiveness. IEA-RETD has completed a study with the overall objective to assist policy makers and project developers in a better understanding of these barriers and the specifics of offshore renewable energy and to give them practical guidelines. These include an offshore energy deployment framework, substantiated by evidence-based analyses, and recommendations for future policies design, including best practices for allocation of seafloor rights.

Industrializing Offshore Wind Power with Serial Assembly and Lower-cost Deployment - Final Report

Energy Technology Data Exchange (ETDEWEB)

Kempton, Willett [Univ. of Delaware, Newark, DE (United States)

2017-12-11

. That design is, in brief: a conventional turbine and tubular tower is mounted on a tripod jacket, in turn atop three suction buckets. Blades are mounted on the tower, not on the hub. The entire structure is built in port, from the bottom up, then assembled structures are queued in the port for deployment. During weather windows, the fully-assembled structures are lifted off the quay, lashed to the vessel, and transported to the deployment site. The vessel analyzed is a shear leg crane vessel with dynamic positioning like the existing Gulliver, or it could be a US-built crane barge. On site, the entire structure is lowered to the bottom by the crane vessel, then pumping of the suction buckets is managed by smaller service vessels. Blades are lifted into place by small winches operated by workers in the nacelle without lift vessel support. Advantages of the selected design include: cost and time at sea of the expensive lift vessel are significantly reduced; no jack up vessel is required; the weather window required for each installation is shorter; turbine structure construction is continuous with a queue feeding the weather-dependent installation process; pre-installation geotechnical work is faster and less expensive; there are no sound impacts on marine mammals, thus minimal spotting and no work stoppage Industrializing Offshore Wind Power 6 of 96 9 for mammal passage; the entire structure can be removed for decommissioning or major repairs; the method has been validated for current turbines up to 10 MW, and a calculation using simple scaling shows it usable up to 20 MW turbines.

77 FR 74196 - Draft Guidance for Industry on Safety Considerations for Product Design To Minimize Medication...

Science.gov (United States)

2012-12-13

... error-prone label and packaging designs. Among these measures, FDA agreed that by the end of FY 2010... minimizing risks with the design of drug product container labels, carton labeling, and packaging... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2012-D-1005...

Miniature field deployable terahertz source

Science.gov (United States)

Mayes, Mark G.

2006-05-01

Developments in terahertz sources include compacted electron beam systems, optical mixing techniques, and multiplication of microwave frequencies. Although significant advances in THz science have been achieved, efforts continue to obtain source technologies that are more mobile and suitable for field deployment. Strategies in source development have approached generation from either end of the THz spectrum, from up-conversion of high-frequency microwave to down-conversion of optical frequencies. In this paper, we present the design of a THz source which employs an up-conversion method in an assembly that integrates power supply, electronics, and radiative component into a man-portable unit for situations in which a lab system is not feasible. This unit will ultimately evolve into a ruggedized package suitable for use in extreme conditions, e.g. temporary security check points or emergency response teams, in conditions where THz diagnostics are needed with minimal planning or logistical support. In order to meet design goals of reduced size and complexity, the inner workings of the unit ideally would be condensed into a monolithic active element, with ancillary systems, e.g. user interface and power, coupled to the element. To attain these goals, the fundamental component of our design is a THz source and lens array that may be fabricated with either printed circuit board or wafer substrate. To reduce the volume occupied by the source array, the design employs a metamaterial composed of a periodic lattice of resonant elements. Each resonant element is an LC oscillator, or tank circuit, with inductance, capacitance, and center frequency determined by dimensioning and material parameters. The source array and supporting electronics are designed so that the radiative elements are driven in-phase to yield THz radiation with a high degree of partial coherence. Simulation indicates that the spectral width of operation may be controlled by detuning of critical dimensions

Final Technical Report: Commercial Advanced Lighting Control (ALC) Demonstration and Deployment

Energy Technology Data Exchange (ETDEWEB)

Arnold, Gabe [Efficiency Forward, Inc. / DesignLights Consortium

2018-02-05

This three-year demonstration and deployment project sought to address market barriers to accelerating the adoption of Advanced Lighting Controls (ALCs), an underutilized technology with low market penetration. ALCs are defined as networked, addressable lighting control systems that utilize software or intelligent controllers to combine multiple energy-saving lighting control strategies in a single space (e.g., smart-time scheduling, daylight harvesting, task tuning, occupancy control, personal control, variable load-shedding, and plug-load control). The networked intelligent aspect of these systems allows applicable lighting control strategies to be combined in a single space, layered over one another, maximizing overall energy-savings. The project included five real building demonstrations of ALCs across the Northeast US region. The demonstrations provided valuable data and experience to support deployment tasks that are necessary to overcome market barriers. These deployment tasks included development of training resources for building designers, installers, and trades, as well as development of new energy efficiency rebates for the technology from Efficiency Forward’s utility partners. Educating designers, installers, and trades on ALCs is a critical task for reducing the cost of the technology that is currently inflated due to perceived complexity and unfamiliarity with how to design and install the systems. Further, utility and non-utility energy efficiency programs continue to relegate the technology to custom or ill-suited prescriptive program designs that do not effectively deploy the technology at scale. This project developed new, scalable rebate approaches for the technology. Efficiency Forward utilized their DesignLights Consortium® (DLC) brand and network of 81 DLC member utilities to develop and deploy the results of the project. The outputs of the project have included five published case studies, a six-hour ALC technology training curriculum

Deployment of e-health services - a business model engineering strategy.

Science.gov (United States)

Kijl, Björn; Nieuwenhuis, Lambert J M; Huis in 't Veld, Rianne M H A; Hermens, Hermie J; Vollenbroek-Hutten, Miriam M R

2010-01-01

We designed a business model for deploying a myofeedback-based teletreatment service. An iterative and combined qualitative and quantitative action design approach was used for developing the business model and the related value network. Insights from surveys, desk research, expert interviews, workshops and quantitative modelling were combined to produce the first business model and then to refine it in three design cycles. The business model engineering strategy provided important insights which led to an improved, more viable and feasible business model and related value network design. Based on this experience, we conclude that the process of early stage business model engineering reduces risk and produces substantial savings in costs and resources related to service deployment.

First Robotic SPECT for Minimally Invasive Sentinel Lymph Node Mapping.

Science.gov (United States)

Fuerst, Bernhard; Sprung, Julian; Pinto, Francisco; Frisch, Benjamin; Wendler, Thomas; Simon, Hervé; Mengus, Laurent; van den Berg, Nynke S; van der Poel, Henk G; van Leeuwen, Fijs W B; Navab, Nassir

2016-03-01

In this paper we present the usage of a drop-in gamma probe for intra-operative Single-Photon Emission Computed Tomography (SPECT) imaging in the scope of minimally invasive robot-assisted interventions. The probe is designed to be inserted and reside inside the abdominal cavity during the intervention. It is grasped during the procedure using a robotic laparoscopic gripper enabling full six degrees of freedom handling by the surgeon. We demonstrate the first deployment of the tracked probe for intra-operative in-patient robotic SPECT enabling augmented-reality image guidance. The hybrid mechanical- and image-based in-patient probe tracking is shown to have an accuracy of 0.2 mm. The overall system performance is evaluated and tested with a phantom for gynecological sentinel lymph node interventions and compared to ground-truth data yielding a mean reconstruction accuracy of 0.67 mm.

Applications of Dynamic Deployment of Services in Industrial Automation

Science.gov (United States)

Candido, Gonçalo; Barata, José; Jammes, François; Colombo, Armando W.

Service-oriented Architecture (SOA) is becoming a de facto paradigm for business and enterprise integration. SOA is expanding into several domains of application envisioning a unified solution suitable across all different layers of an enterprise infrastructure. The application of SOA based on open web standards can significantly enhance the interoperability and openness of those devices. By embedding a dynamical deployment service even into small field de- vices, it would be either possible to allow machine builders to place built- in services and still allow the integrator to deploy on-the-run the services that best fit his current application. This approach allows the developer to keep his own preferred development language, but still deliver a SOA- compliant application. A dynamic deployment service is envisaged as a fundamental framework to support more complex applications, reducing deployment delays, while increasing overall system agility. As use-case scenario, a dynamic deployment service was implemented over DPWS and WS-Management specifications allowing designing and programming an automation application using IEC61131 languages, and deploying these components as web services into devices.

Capitalized design of smart medicine box for elderly person based on quality function deployment (QFD)

Science.gov (United States)

Lestari, Brina Cindy; Dewi, Dyah Santhi; Widodo, Rusminto Tjatur

2017-11-01

The elderly who has a particular disease need to take some medicines in everyday with correct dosages and appropriate by time schedules. However, the elderly frequently forget to take medicines because of their memory weakened. Consequently, the product innovation of elderly healthcare is required for helping elderly takes some medicine more easily. This research aims to develop a smart medicine box by applying quality function deployment method. The first step is identifying elderly requirements through an ethnographic approach by interviewing thirty-two of elderly people as respondents. Then, the second step is translated elderly requirements to technical parameter for designing a smart medicine box. The smart box design is focused on two main requirements which have highest importance rating including alarm reminder for taking medicine and automatic medicine box. Finally, the prototype design has been created and tested by using usability method. The result shown that 90% from ten respondents have positive respond on the feature of smart medicine box. The voice of alarm reminder smart medicine box is easy to understand by elderly people for taking medicines.

Simplified swift and safe vascular closure device deployment without a local arteriogram: Single center experience in 2074 consecutive patients

Directory of Open Access Journals (Sweden)

Antonis S. Manolis

2016-07-01

Conclusion: Deployment of Angio-Seal without use of local angiography was efficacious and safe, characterized by a high success rate of deployment and hemostasis with few correctable complications in a large patient cohort undergoing transfemoral catheterization for PCI and non-PCI procedures under anticoagulation and antiplatelet drug therapy. VCD reduced the time-to-hemostasis and time-to-mobilization and minimized the incidence of complications.

Completion plug design provides improved operational efficiency and safety while minimizing environmental risks

Energy Technology Data Exchange (ETDEWEB)

Dum, Frank [T.D. Williamson, Inc., Tulsa, OK (United States)

2012-07-01

Pipeline repair standards have been raised with recent improvements for completion plugs when used with a brand new setting tool, resulting in lower environmental risks, improved operational efficiency and safety. The design changes were originally made to serve in an offshore environment in order to minimize the diver's time in the water and simplify steps by the diver to execute pipeline repair operations in cold, dark conditions. Enhancements in the design include fewer number of fittings, plugs, o-rings and gaskets isolating the pipeline product found inside the pipe. The new design is a step toward meeting strict operational and safety standards demanded in the field of pipeline maintenance and repair. (author)

A space release/deployment system actuated by shape memory wires

Science.gov (United States)

Fragnito, Marino; Vetrella and, Sergio

2002-11-01

In this paper, the design of an innovative hold down/release and deployment device actuated by shape memory wires, to be used for the first time for the S MA RT microsatellite solar wings is shown. The release and deployment mechanisms are actuated by a Shape Memory wire (Nitinol), which allows a complete symmetrical and synchronous release, in a very short time, of the four wings in pairs. The hold down kinematic mechanism is preloaded to avoid vibration nonlinearities and unwanted deployment at launch. The deployment mechanism is a simple pulley system. The stiffness of the deployed panel-hinge system needs to be dimensioned in order to meet the on-orbit requirement for attitude control. One-way roller clutches are used to keep the panel at the desired angle during the mission. An ad hoc software has been developed to simulate both the release and deployment operations, coupling the SMA wire behavior with the system mechanics.

A Small Spacecraft Swarm Deployment and Stationkeeping Strategy for Sun-Earth L1 Halo Orbits

Science.gov (United States)

Renea Conn, Tracie; Bookbinder, Jay

2018-01-01

Spacecraft orbits about the Sun-Earth librarian point L1 have been of interest since the 1950s. An L1 halo orbit was first achieved with the International Sun-Earth Explorer-3 (ISEE-3) mission, and similar orbits around Sun-Earth L1 were achieved in the Solar and Heliospheric Observatory (SOHO), Advanced Composition Explorer (ACE), Genesis, and Deep Space Climate Observatory (DSCOVR) missions. With recent advancements in CubeSat technology, we envision that it will soon be feasible to deploy CubeSats at L1. As opposed to these prior missions where one large satellite orbited alone, a swarm of CubeSats at L1 would enable novel science data return, providing a topology for intersatellite measurements of heliophysics phenomena both spatially and temporally, at varying spatial scales.The purpose of this iPoster is to present a flight dynamics strategy for a swarm of numerous CubeSats orbiting Sun-Earth L1. The presented method is a coupled, two-part solution. First, we present a deployment strategy for the CubeSats that is optimized to produce prescribed, time-varying intersatellite baselines for the purposes of collecting magnetometer data as well as radiometric measurements from cross-links. Second, we employ a loose control strategy that was successfully applied to SOHO and ACE for minimized stationkeeping propellant expenditure. We emphasize that the presented solution is practical within the current state-of-the-art and heritage CubeSat technology, citing capabilities of CubeSat designs that will launch on the upcoming Exploration Mission 1 (EM-1) to lunar orbits and beyond. Within this iPoster, we present animations of the simulated deployment strategy and resulting spacecraft trajectories. Mission design parameters such as total Δv required for long-term station keeping and minimum/maximum/mean spacecraft separation distances are also presented.

Deployment strategies of managed lanes on arterials.

Science.gov (United States)

2015-02-01

This report investigates issues related to planning, financing, deployment, and operation of managed : lanes on arterials. In this report, a strategy for managed lanes refers to a combination of the managed : lane type, the design and implementation,...

Molten salt reactors and possible scenarios for future nuclear power deployment

International Nuclear Information System (INIS)

Merle-Lucotte, E.; Mathieu, L.; Heuer, D.; Loiseaux, J. M.; Billebaud, A.; Brissot, R.; David, S.; Garzenne, C.; Laulan, O.; Le Brun, C.; Lecarpentier, D.; Liatard, E.; Meplan, O.; Michel-Sendis, F.; Nuttin, A.; Perdu, F.

2004-01-01

An important fraction of the nature energy demand may be satisfied by nuclear power. In this context, the possibilities of worldwide nuclear deployment are studied. We are convinced that the Molten Salt Reactors may play a central role in this deployment. The Molten Salt Reactor needs to be coupled to a reprocessing unit in order to extract the Fission Products which poison the core. The efficiency of this reprocessing has a crucial influence on reactor behavior especially for the breeding ratio. The Molten Salt Breeder Reactor project was based on an intensive reprocessing for high breeding purposes. A new concept of Thorium Molten Salt Reactor is presented here. Including this new concept in the worldwide nuclear deployment, to satisfy these power needs, we consider three typical scenarios, based on three reactor types: Pressurized Water Reactor, Fast Neutron Reactor and Thorium Molten Salt Reactor. The aim of this paper is to demonstrate, in a first hand that a Thorium Molten Salt Reactor can be realistic, with correct temperature coefficients and at least iso-breeder with slow reprocessing and new geometry; on the other hand that such Molten Salt Reactors enable a successful nuclear deployment, while minimizing fuel and waste management problems. (authors)

Novel Deployment Mechanism for Conventional Solar Array Enhancement

Directory of Open Access Journals (Sweden)

Hodgetts Paul A.

2017-01-01

Full Text Available A novel mechanism is described, by which flexible blankets could be deployed from existing solar panel designs. These blankets could be covered with flexible cells, or they could be reflective films to form a concentrator array. Either way, the performance of an existing array design could be enhanced.

RSG Deployment Case Testing Results

Energy Technology Data Exchange (ETDEWEB)

Owsley, Stanley L.; Dodson, Michael G.; Hatchell, Brian K.; Seim, Thomas A.; Alexander, David L.; Hawthorne, Woodrow T.

2005-09-01

The RSG deployment case design is centered on taking the RSG system and producing a transport case that houses the RSG in a safe and controlled manner for transport. The transport case was driven by two conflicting constraints, first that the case be as light as possible, and second that it meet a stringent list of Military Specified requirements. The design team worked to extract every bit of weight from the design while striving to meet the rigorous Mil-Spec constraints. In the end compromises were made primarily on the specification side to control the overall weight of the transport case. This report outlines the case testing results.

A stowing and deployment strategy for large membrane space systems on the example of Gossamer-1

Science.gov (United States)

Seefeldt, Patric

2017-09-01

Deployment systems for innovative space applications such as solar sails require a technique for a controlled and autonomous deployment in space. The deployment process has a strong impact on the mechanism and structural design and sizing. On the example of the design implemented in the Gossamer-1 project of the German Aerospace Center (DLR), such a stowing and deployment process is analyzed. It is based on a combination of zig-zag folding and coiling of triangular sail segments spanned between crossed booms. The deployment geometry and forces introduced by the mechanism considered are explored in order to reveal how the loads are transferred through the membranes to structural components such as the booms. The folding geometry and force progressions are described by function compositions of an inverse trigonometric function with the considered trigonometric function itself. If these functions are evaluated over several periods of the trigonometric function, a non-smooth oscillating curve occurs. Depending on the trigonometric function, these are often vividly described as zig-zag or sawtooth functions. The developed functions are applied to the Gossamer-1 design. The deployment geometry reveals a tendency that the loads are transferred along the catheti of the sail segments and therefore mainly along the boom axes. The load introduced by the spool deployment mechanism is described. By combining the deployment geometry with that load, a prediction of the deployment load progression is achieved. The mathematical description of the stowing and deployment geometry, as well as the forces inflicted by the mechanism provides an understanding of how exactly the membrane deploys and through which edges the deployment forces are transferred. The mathematical analysis also gives an impression of sensitive parameters that could be influenced by manufacturing tolerances or unsymmetrical deployment of the sail segments. While the mathematical model was applied on the design of

Systematic process synthesis and design methods for cost effective waste minimization

International Nuclear Information System (INIS)

Biegler, L.T.; Grossman, I.E.; Westerberg, A.W.

1995-01-01

We present progress on our work to develop synthesis methods to aid in the design of cost effective approaches to waste minimization. Work continues to combine the approaches of Douglas and coworkers and of Grossmann and coworkers on a hierarchical approach where bounding information allows it to fit within a mixed integer programming approach. We continue work on the synthesis of reactors and of flexible separation processes. In the first instance, we strive for methods we can use to reduce the production of potential pollutants, while in the second we look for ways to recover and recycle solvents

Systematic process synthesis and design methods for cost effective waste minimization

Energy Technology Data Exchange (ETDEWEB)

Biegler, L.T.; Grossman, I.E.; Westerberg, A.W. [Carnegie Mellon Univ., Pittsburgh, PA (United States)

1995-12-31

We present progress on our work to develop synthesis methods to aid in the design of cost effective approaches to waste minimization. Work continues to combine the approaches of Douglas and coworkers and of Grossmann and coworkers on a hierarchical approach where bounding information allows it to fit within a mixed integer programming approach. We continue work on the synthesis of reactors and of flexible separation processes. In the first instance, we strive for methods we can use to reduce the production of potential pollutants, while in the second we look for ways to recover and recycle solvents.

Mastering Windows 7 Deployment

CERN Document Server

Finn, Aidan; van Surksum, Kenneth

2011-01-01

Get professional-level instruction on Windows 7 deployment tools Enterprise-level operating system deployment is challenging and requires knowledge of specific tools. It is expected that Windows 7 will be extensively deployed in businesses worldwide. This comprehensive Sybex guide provides thorough coverage of the Microsoft deployment tools that were specifically created for Windows 7, preparing system administrators, MIS professionals, and corporate programmers to tackle the task effectively.Companies worldwide are expected to deploy Windows 7 as their enterprise operating system; system admi

Multi-Site Project Management A Program for Reducing the Cost of Technology Deployment at Department of Energy Sites

International Nuclear Information System (INIS)

Davis, N.R.; Selden, E.R.; Little, D.B.; Coleman, M.C.; Bennett, J.T.

2009-01-01

Retrieval and processing of High Level Waste (HLW) stored in Department of Energy (DOE) waste tanks is performed to support closure of the tanks as required by site specific regulatory agreements. Currently, there are four sites in the DOE Complex that have HLW tanks and must process and disposition HLW. As such, there is an opportunity to achieve an economy of scale and reduce duplication of efforts. Two or more sites typically have similar technology development and deployment needs. Technology development is already executed at the national level. As the technology is matured, the next step is to commission a design/build project. Typically each site performs this separately due to differences in waste type, tank design, site specific considerations such as proximity to the water table or to the site boundary. The focus of the individual sites tends to be on the differences between sites versus on the similarities thus there is an opportunity to minimize the cost for similar deployments. A team of engineers and project management professionals from the Savannah River Site has evaluated technology needs at the four HLW sites and determined that there is an economy of scale that can be achieved by specific technology deployments in the area of waste retrieval, waste pretreatment and waste disposition. As an example, the Waste on Wheels tank retrieval system (presented in the 2006 Waste Management Symposium) was designed and fabricated in portable modules that could be installed in HLW tanks at Hanford, Savannah River or Idaho. This same concept could be used for modular in-tank cesium removal process and equipment, tank cleaning mechanical equipment, and chemical tank cleaning process and equipment. The purpose of this paper is to present a multi-site project management approach that will reduce deployment costs and be consistent with DOE Order 413.3 project management principles. The approach will describe how projects can be managed by a lead site with

The Risk Management in New Technology Deployment to Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Jung, Kil Young; Roh, Myung Sub [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

2013-10-15

This paper figures out that it is required to build the structured and integrated risk management system in enterprise level. By means of it, the accumulated data and experience of work can be shared and transferred effectively among workers, and consequently design mistake or error can be reduced. It has been requested to upgrade and replace equipment in Nuclear Power Plant (NPP) with new technology because of obsolescence and spare parts issues, and demands for higher performance. The processes for the new technology deployment to NPP, however, may have risks causing the unpredictable outcomes leading to the degradation of performance or operation. Therefore, the proper risk management is essential for ensuring safety and performance of NPP since it provides means to identify risks and minimizing their impacts. For these reason, this paper aims at investigating how the risk is managed and presents the proper risk management in project for the deployment of new technology to NPP. This paper investigated how the risk is managed in the NPP industry. Risk is perceived as a negative term that brings negative impact on project objectives. 10 key risks are identified and classified as high risk on cost, time, scope, or quality in compliance with the criteria seeking 'Safety First'. Design mistake or error' can significantly influence three project objectives while the rest risks can significantly influence one or two project objectives. However, it is also found that there are neither structured ways nor a systematical approach to perform the proper risk management. As a result, risk management such as identification, assessment, and response is mostly performed in the individual level laying much weight on experience since the most common methods are past experience and review of similar case.

The Risk Management in New Technology Deployment to Nuclear Power Plant

International Nuclear Information System (INIS)

Jung, Kil Young; Roh, Myung Sub

2013-01-01

This paper figures out that it is required to build the structured and integrated risk management system in enterprise level. By means of it, the accumulated data and experience of work can be shared and transferred effectively among workers, and consequently design mistake or error can be reduced. It has been requested to upgrade and replace equipment in Nuclear Power Plant (NPP) with new technology because of obsolescence and spare parts issues, and demands for higher performance. The processes for the new technology deployment to NPP, however, may have risks causing the unpredictable outcomes leading to the degradation of performance or operation. Therefore, the proper risk management is essential for ensuring safety and performance of NPP since it provides means to identify risks and minimizing their impacts. For these reason, this paper aims at investigating how the risk is managed and presents the proper risk management in project for the deployment of new technology to NPP. This paper investigated how the risk is managed in the NPP industry. Risk is perceived as a negative term that brings negative impact on project objectives. 10 key risks are identified and classified as high risk on cost, time, scope, or quality in compliance with the criteria seeking 'Safety First'. Design mistake or error' can significantly influence three project objectives while the rest risks can significantly influence one or two project objectives. However, it is also found that there are neither structured ways nor a systematical approach to perform the proper risk management. As a result, risk management such as identification, assessment, and response is mostly performed in the individual level laying much weight on experience since the most common methods are past experience and review of similar case

Experimental and Analytical Evaluation of a Composite Honeycomb Deployable Energy Absorber

Science.gov (United States)

Jackson, Karen E.; Kellas, Sotiris; Horta, Lucas G.; Annett, Martin S.; Polanco, Michael A.; Littell, Justin D.; Fasanella, Edwin L.

2011-01-01

In 2006, the NASA Subsonic Rotary Wing Aeronautics Program sponsored the experimental and analytical evaluation of an externally deployable composite honeycomb structure that is designed to attenuate impact energy during helicopter crashes. The concept, which is designated the Deployable Energy Absorber (DEA), utilizes an expandable Kevlar honeycomb structure to dissipate kinetic energy through crushing. The DEA incorporates a unique flexible hinge design that allows the honeycomb to be packaged and stowed flat until needed for deployment. A variety of deployment options such as linear, radial, and/or hybrid methods can be used. Experimental evaluation of the DEA utilized a building block approach that included material characterization testing of its constituent, Kevlar -129 fabric/epoxy, and flexural testing of single hexagonal cells. In addition, the energy attenuation capabilities of the DEA were demonstrated through multi-cell component dynamic crush tests, and vertical drop tests of a composite fuselage section, retrofitted with DEA blocks, onto concrete, water, and soft soil. During each stage of the DEA evaluation process, finite element models of the test articles were developed and simulations were performed using the explicit, nonlinear transient dynamic finite element code, LS-DYNA. This report documents the results of the experimental evaluation that was conducted to assess the energy absorption capabilities of the DEA.

Creating a Comprehensive Solar Water Heating Deployment Strategy

International Nuclear Information System (INIS)

Focus Marketing Services

1999-01-01

This report details the results of a research conducted in 1998 and 1999 and outlines a marketing deployment plan designed for businesses interested in marketing solar water heaters in the new home industry

Creating a Comprehensive Solar Water Heating Deployment Strategy

Energy Technology Data Exchange (ETDEWEB)

Focus Marketing Services

1999-08-18

This report details the results of a research conducted in 1998 and 1999 and outlines a marketing deployment plan designed for businesses interested in marketing solar water heaters in the new home industry.

Multi-Criteria Optimization of the Deployment of a Grid for Rural Electrification Based on a Heuristic Method

Science.gov (United States)

Ortiz-Matos, L.; Aguila-Tellez, A.; Hincapié-Reyes, R. C.; González-Sanchez, J. W.

2017-07-01

In order to design electrification systems, recent mathematical models solve the problem of location, type of electrification components, and the design of possible distribution microgrids. However, due to the amount of points to be electrified increases, the solution to these models require high computational times, thereby becoming unviable practice models. This study posed a new heuristic method for the electrification of rural areas in order to solve the problem. This heuristic algorithm presents the deployment of rural electrification microgrids in the world, by finding routes for optimal placement lines and transformers in transmission and distribution microgrids. The challenge is to obtain a display with equity in losses, considering the capacity constraints of the devices and topology of the land at minimal economic cost. An optimal scenario ensures the electrification of all neighbourhoods to a minimum investment cost in terms of the distance between electric conductors and the amount of transformation devices.

Design Optimization of Transformerless Grid-Connected PV Inverters Including Reliability

OpenAIRE

Koutroulis, Eftichios; Blaabjerg, Frede

2013-01-01

This paper presents a new methodology for optimal design of transformerless photovoltaic (PV) inverters targeting a cost-effective deployment of grid-connected PV systems. The optimal switching frequency as well as the optimal values and types of the PV inverter components is calculated such that the PV inverter LCOE generated during the PV system lifetime period is minimized. The LCOE is also calculated considering the failure rates of the components, which affect the reliability performance...

The risk for marital infidelity across a year-long deployment.

Science.gov (United States)

Balderrama-Durbin, Christina; Stanton, Kimberley; Snyder, Douglas K; Cigrang, Jeffrey A; Talcott, G Wayne; Smith Slep, Amy M; Heyman, Richard E; Cassidy, Daniel G

2017-08-01

Military deployment can create significant relationship strain. Although most couples navigate the challenges of deployment successfully, this period may render some couples more vulnerable to adverse relationship outcomes such as infidelity due to a convergence of factors including geographic separation and reduced emotional and physical intimacy. Despite anecdotal reports of increased rates of infidelity during deployment, empirical findings are lacking. This study used a prospective design to examine the prevalence and risk factors of infidelity across the deployment cycle including a year-long deployment to Iraq. A total of 63 married male Airmen were assessed both pre- and 6-9 months postdeployment. The rate of sexual infidelity prior to deployment (21%) was commensurate with the lifetime rate of sexual involvement outside the marriage in representative community samples of men. Across the deployment period, the prevalence of sexual infidelity was strikingly high (22.6%) compared with annual community estimates (1.5-4%; Allen et al., 2005). Findings demonstrated that service members with a prior history of separation, steps toward divorce, and relationship distress prior to deployment had elevated risk for infidelity over the deployment cycle. Moreover, roughly 75% of Airmen who experienced infidelity over the deployment cycle divorced by 6-9 months postdeployment whereas only 5% of service members without infidelity divorced during this same time period. Considering well-documented adverse impacts of infidelity and divorce, the current findings may assist in identifying military couples at risk for infidelity and informing targeted prevention or early intervention strategies for these couples prior to or immediately following deployment. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

AP1000{sup R} licensing and deployment in the United States

Energy Technology Data Exchange (ETDEWEB)

Jordan, R. P.; Russ, P. A.; Filiak, P. P.; Castiglione, L. L. [Westinghouse Electric Company LLC, 1000 Westinghouse Drive, Cranberry Township, PA 16066 (United States)

2012-07-01

In recent years, both domestic and foreign utilities have turned to the standardized Westinghouse AP1000 plant design in satisfying their near - and long-term - sustainable energy needs. As direct support to these actions, licensing the AP1000 design has played a significant role by providing one of the fundamental bases in clearing regulatory hurdles leading to the start of new plant construction. Within the U.S. alone, Westinghouse AP1000 licensing activities have reached unprecedented milestones with the approvals of both AP1000 Design Certification and Southern Company's combined construction permit and operating license (COL) application directly supporting the construction of two new nuclear plants in Georgia. Further COL application approvals are immediately pending for an additional two AP1000 plants in South Carolina. And, across the U.S. nuclear industry spectrum, there are 10 other COL applications under regulatory review representing some 16 new plants at 10 sites. In total, these actions represent the first wave of new plant licensing under the regulatory approval process since 1978. Fundamental to the Nuclear Regulatory Commission's AP1000 Design Certification is the formal recognition of the AP1000 passive safety design through regulatory acceptance rulemaking. Through recognition and deployment of the AP1000 Design Certification, the utility licensee / operator of this reactor design are now offered an opportunity to use a simplified 'one-step' combined license process, thereby managing substantial back-end construction schedule risk from regulatory and intervention delays. Application of this regulatory philosophy represents both acceptance and encouragement of standardized reactor designs like the AP1000. With the recent AP1000 Design Certification and utility COL acceptances, the fundamental licensing processes of this philosophy have successfully proven the attainment of significant milestones with the next stage licensing

A Modular Approach To Developing A Large Deployable Reflector

Science.gov (United States)

Pittman, R.; Leidich, C.; Mascy, F.; Swenson, B.

1984-01-01

NASA is currently studying the feasibility of developing a Large Deployable Reflector (LDR) astronomical facility to perform astrophysical studies of the infrared and submillimeter portion of the spectrum in the mid 1990's. The LDR concept was recommended by the Astronomy Survey Committee of the National Academy of Sciences as one of two space based projects to be started this decade. The current baseline calls for a 20 m (65.6 ft) aperture telescope diffraction limited at 30 μm and automatically deployed from a single Shuttle launch. The volume, performance, and single launch constraints place great demands on the technology and place LDR beyond the state-of-the-art in certain areas such as lightweight reflector segments. The advent of the Shuttle is opening up many new options and capabilities for producing large space systems. Until now, LDR has always been conceived as an integrated system, deployed autonomously in a single launch. This paper will look at a combination of automatic deployment and on-orbit assembly that may reduce the technological complexity and cost of the LDR system. Many technological tools are now in use or under study that will greatly enhance our capabilities to do assembly in space. Two Shuttle volume budget scenarios will be examined to assess the potential of these tools to reduce the LDR system complexity. Further study will be required to reach the full optimal combination of deployment and assembly, since in most cases the capabilities of these new tools have not been demonstrated. In order to take maximum advantage of these concepts, the design of LDR must be flexible and allow one subsystem to be modified without adversely affecting the entire system. One method of achieving this flexibility is to use a modular design approach in which the major subsystems are physically separated during launch and assembled on orbit. A modular design approach facilitates this flexibility but requires that the subsystems be interfaced in a simple

Design of power controller in CDMA system with power and SIR error minimization

Institute of Scientific and Technical Information of China (English)

Shulan KONG; Huanshui ZHANG; Zhaosheng ZHANG; Hongxia WANG

2007-01-01

In this paper, an uplink power control problem is considered for code division multiple access (CDMA) systems. A distributed algorithm is proposed based on linear quadratic optimal control theory. The proposed scheme minimizes the sum of the power and the error of signal-to-interference ratio (SIR). A power controller is designed by constructing an optimization problem of a stochastic linear quadratic type in Krein space and solving a Kalman filter problem.

Low-cost small scale parabolic trough collector design for manufacturing and deployment in Africa

Science.gov (United States)

Orosz, Matthew; Mathaha, Paul; Tsiu, Anadola; Taele, B. M.; Mabea, Lengeta; Ntee, Marcel; Khakanyo, Makoanyane; Teker, Tamer; Stephens, Jordan; Mueller, Amy

2016-05-01

Concentrating Solar Power is expanding its deployment on the African subcontinent, highlighting the importance of efforts to indigenize manufacturing of this technology to increase local content and therefore local economic benefits of these projects. In this study a design for manufacturing (DFM) exercise was conducted to create a locally produced parabolic trough collector (the G4 PTC). All parts were sourced or fabricated at a production facility in Lesotho, and several examples of the design were prototyped and tested with collaborators in the Government of Lesotho's Appropriate Technology Services division and the National University of Lesotho. Optical and thermal performance was simulated and experimentally validated, and pedagogical pre-commercial versions of the PTC have been distributed to higher education partners in Lesotho and Europe. The cost to produce the PTC is 180 USD/m2 for a locally manufactured heat collection element (HCE) capable of sustaining 250C operation at ~65% efficiency. A version with an imported evacuated HCE can operate at 300°C with 70% efficiency. Economically relevant applications for this locally produced PTC include industrial process heat and distributed generation scenarios where cogeneration is required.

Pre-deployment dissociation and personality as risk factors for post-deployment post-traumatic stress disorder in Danish soldiers deployed to Afghanistan

DEFF Research Database (Denmark)

Ponce de León, Beatriz; Andersen, Søren; Karstoft, Karen Inge

2018-01-01

Objective: This study investigated whether pre-deployment dissociation was associated with previously identified post-traumatic stress disorder (PTSD) symptom trajectories from before to 2.5 years after military deployment. Furthermore, it examined whether the tendency to dissociate, pre-deployme......Objective: This study investigated whether pre-deployment dissociation was associated with previously identified post-traumatic stress disorder (PTSD) symptom trajectories from before to 2.5 years after military deployment. Furthermore, it examined whether the tendency to dissociate, pre...

Using Quality Function Deployment To Improve Academic Advising Processes.

Science.gov (United States)

Barrows, Richard; Murray, Bruce

1997-01-01

Quality Function Deployment, a set of concepts and tools used in manufacturing engineering to link consumer needs with product design, can also improve academic advising systems and processes. The technique promotes structured, logical examination of students' advising needs and their relationship to advising system design, processes, methods,…

A Location-Aware Service Deployment Algorithm Based on K-Means for Cloudlets

Directory of Open Access Journals (Sweden)

Tyng-Yeu Liang

2017-01-01

Full Text Available Cloudlet recently was proposed to push data centers towards network edges for reducing the network latency of delivering cloud services to mobile devices. For the sake of user mobility, it is necessary to deploy and hand off services anytime anywhere for achieving the minimal network latency for users’ service requests. However, the cost of this solution usually is too high for service providers and is not effective for resource exploitation. To resolve this problem, we propose a location-aware service deployment algorithm based on K-means for cloudlets in this paper. Simply speaking, the proposed algorithm divides mobile devices into a number of device clusters according to the geographical location of mobile devices and then deploys service instances onto the edge cloud servers nearest to the centers of device clusters. Our performance evaluation has shown that the proposed algorithm can effectively reduce not only the network latency of edge cloud services but also the number of service instances used for satisfying the condition of tolerable network latency.

An efficient genetic algorithm for maximum coverage deployment in wireless sensor networks.

Science.gov (United States)

Yoon, Yourim; Kim, Yong-Hyuk

2013-10-01

Sensor networks have a lot of applications such as battlefield surveillance, environmental monitoring, and industrial diagnostics. Coverage is one of the most important performance metrics for sensor networks since it reflects how well a sensor field is monitored. In this paper, we introduce the maximum coverage deployment problem in wireless sensor networks and analyze the properties of the problem and its solution space. Random deployment is the simplest way to deploy sensor nodes but may cause unbalanced deployment and therefore, we need a more intelligent way for sensor deployment. We found that the phenotype space of the problem is a quotient space of the genotype space in a mathematical view. Based on this property, we propose an efficient genetic algorithm using a novel normalization method. A Monte Carlo method is adopted to design an efficient evaluation function, and its computation time is decreased without loss of solution quality using a method that starts from a small number of random samples and gradually increases the number for subsequent generations. The proposed genetic algorithms could be further improved by combining with a well-designed local search. The performance of the proposed genetic algorithm is shown by a comparative experimental study. When compared with random deployment and existing methods, our genetic algorithm was not only about twice faster, but also showed significant performance improvement in quality.

Minimization of Antinutrients in Idli by Using Response Surface Process Optimization

NARCIS (Netherlands)

Sharma, Anand; Kumari, Sarita; Nout, Martinus J.R.; Sarkar, Prabir K.

2017-01-01

Deploying response surface methodology, the stages of idli preparation were optimized for minimizing the level of antinutrients. Under optimum conditions of soaking blackgram dal (1:5 of dal and water at 16C, and pH 4.0 for 18 h) and rice (1:5 of rice and water at 16C, and pH 5.6 for 18 h), the

Risk and protective factors for suicidal ideation and suicide attempts among deployed Danish soldiers from 1990 to 2009.

Science.gov (United States)

Ejdesgaard, Bo Andersen; Zøllner, Lilian; Jensen, Børge Frank; Jørgensen, Hans-Ole; Kähler, Henrik

2015-01-01

The study was undertaken to identify risk and protective factors for suicidal ideation and suicide attempts among deployed Danish soldiers. Research on suicide among Danish veterans has only been conducted to a limited degree. The method applied was a questionnaire survey administered to a population of 1,264 Danish soldiers deployed from 1990 to 2009. The data were analyzed using backward logistic regression modeling in SAS 9.2. In the logistic regression analysis, the following were significant risk factors for suicidal ideation: drug abuse, a poor financial situation before deployment, a heavy workload and/or repatriation during deployment, and attending a poor athletic and recreation program after deployment. Significant protective factors against suicidal ideation were support from friends at home during deployment and appreciation by the general population after deployment. Significant risk factors for suicide attempts were an unhappy childhood and pointless tasks during deployment. No significant protective factors against suicide attempts were identified. On the basis of the results presented in this study, intervention against suicidal behavior would benefit from screening for certain childhood issues, drug abuse, and poor financial situation before deployment. During deployment, measures should be taken to minimize the amount of meaningless tasks and heavy workloads. At the same time, efficient ways of communicating with home should be ensured. After deployment, good athletic and recreation programs should be warranted for all military personnel-including repatriated soldiers. Finally, priority should be given to ensure public appreciation of what deployed soldiers accomplish. Reprint & Copyright © 2015 Association of Military Surgeons of the U.S.

Precision Deployable Mast for the SWOT KaRIn Instrument

Data.gov (United States)

National Aeronautics and Space Administration — Design and prototype a lightweight, precision-deployable mast for the Ka-band Radar Interferometer (KaRIn) antennas in the Surface Water and Ocean Topography (SWOT)...

Design of a minimally constraining, passively supported gait training exoskeleton: ALEX II.

Science.gov (United States)

Winfree, Kyle N; Stegall, Paul; Agrawal, Sunil K

2011-01-01

This paper discusses the design of a new, minimally constraining, passively supported gait training exoskeleton known as ALEX II. This device builds on the success and extends the features of the ALEX I device developed at the University of Delaware. Both ALEX (Active Leg EXoskeleton) devices have been designed to supply a controllable torque to a subject's hip and knee joint. The current control strategy makes use of an assist-as-needed algorithm. Following a brief review of previous work motivating this redesign, we discuss the key mechanical features of the new ALEX device. A short investigation was conducted to evaluate the effectiveness of the control strategy and impact of the exoskeleton on the gait of six healthy subjects. This paper concludes with a comparison between the subjects' gait both in and out of the exoskeleton. © 2011 IEEE

Wireless Sensor Network Deployment for Monitoring Wildlife Passages

Science.gov (United States)

Garcia-Sanchez, Antonio-Javier; Garcia-Sanchez, Felipe; Losilla, Fernando; Kulakowski, Pawel; Garcia-Haro, Joan; Rodríguez, Alejandro; López-Bao, José-Vicente; Palomares, Francisco

2010-01-01

Wireless Sensor Networks (WSNs) are being deployed in very diverse application scenarios, including rural and forest environments. In these particular contexts, specimen protection and conservation is a challenge, especially in natural reserves, dangerous locations or hot spots of these reserves (i.e., roads, railways, and other civil infrastructures). This paper proposes and studies a WSN based system for generic target (animal) tracking in the surrounding area of wildlife passages built to establish safe ways for animals to cross transportation infrastructures. In addition, it allows target identification through the use of video sensors connected to strategically deployed nodes. This deployment is designed on the basis of the IEEE 802.15.4 standard, but it increases the lifetime of the nodes through an appropriate scheduling. The system has been evaluated for the particular scenario of wildlife monitoring in passages across roads. For this purpose, different schemes have been simulated in order to find the most appropriate network operational parameters. Moreover, a novel prototype, provided with motion detector sensors, has also been developed and its design feasibility demonstrated. Original software modules providing new functionalities have been implemented and included in this prototype. Finally, main performance evaluation results of the whole system are presented and discussed in depth. PMID:22163601

Wireless Sensor Network Deployment for Monitoring Wildlife Passages

Directory of Open Access Journals (Sweden)

José-Vicente López-Bao

2010-08-01

Full Text Available Wireless Sensor Networks (WSNs are being deployed in very diverse application scenarios, including rural and forest environments. In these particular contexts, specimen protection and conservation is a challenge, especially in natural reserves, dangerous locations or hot spots of these reserves (i.e., roads, railways, and other civil infrastructures. This paper proposes and studies a WSN based system for generic target (animal tracking in the surrounding area of wildlife passages built to establish safe ways for animals to cross transportation infrastructures. In addition, it allows target identification through the use of video sensors connected to strategically deployed nodes. This deployment is designed on the basis of the IEEE 802.15.4 standard, but it increases the lifetime of the nodes through an appropriate scheduling. The system has been evaluated for the particular scenario of wildlife monitoring in passages across roads. For this purpose, different schemes have been simulated in order to find the most appropriate network operational parameters. Moreover, a novel prototype, provided with motion detector sensors, has also been developed and its design feasibility demonstrated. Original software modules providing new functionalities have been implemented and included in this prototype. Finally, main performance evaluation results of the whole system are presented and discussed in depth.

Abstracting application deployment on Cloud infrastructures

Science.gov (United States)

Aiftimiei, D. C.; Fattibene, E.; Gargana, R.; Panella, M.; Salomoni, D.

2017-10-01

Deploying a complex application on a Cloud-based infrastructure can be a challenging task. In this contribution we present an approach for Cloud-based deployment of applications and its present or future implementation in the framework of several projects, such as “!CHAOS: a cloud of controls” [1], a project funded by MIUR (Italian Ministry of Research and Education) to create a Cloud-based deployment of a control system and data acquisition framework, “INDIGO-DataCloud” [2], an EC H2020 project targeting among other things high-level deployment of applications on hybrid Clouds, and “Open City Platform”[3], an Italian project aiming to provide open Cloud solutions for Italian Public Administrations. We considered to use an orchestration service to hide the complex deployment of the application components, and to build an abstraction layer on top of the orchestration one. Through Heat [4] orchestration service, we prototyped a dynamic, on-demand, scalable platform of software components, based on OpenStack infrastructures. On top of the orchestration service we developed a prototype of a web interface exploiting the Heat APIs. The user can start an instance of the application without having knowledge about the underlying Cloud infrastructure and services. Moreover, the platform instance can be customized by choosing parameters related to the application such as the size of a File System or the number of instances of a NoSQL DB cluster. As soon as the desired platform is running, the web interface offers the possibility to scale some infrastructure components. In this contribution we describe the solution design and implementation, based on the application requirements, the details of the development of both the Heat templates and of the web interface, together with possible exploitation strategies of this work in Cloud data centers.

Quality function deployment QFD: benefits and limitations when applied to designing myoelectric prosthesis hand

Directory of Open Access Journals (Sweden)

Erika Sofía Olaya Escobar

2005-01-01

Full Text Available Quality, cost and time spent in developing products have a direct impact on a company's productivity, market share and profitability. Greater attention must be paid to quality and quicker responses made as customers become more aware of satisfying their longings. This means that a company must be first in delivering a product or service which customers desire if ti wishes to gain and maintain market share. A company's market share and profit margin will depend on the balance and optimisation achieved between quality, cost and time. It is thus important to implant a method like Quality Function Deployment (QFD leading to planning product development during eartly design stages and consequently establish such equilibrium. This article's purpose is to present benefits and limitations regarding QFD; one should be aware of them and QFD development when identifying the most viable to be applied according to each company's inherent characteristics.

Deployment strategy for battery energy storage system in distribution network based on voltage violation regulation

Science.gov (United States)

Wu, H.; Zhou, L.; Xu, T.; Fang, W. L.; He, W. G.; Liu, H. M.

2017-11-01

In order to improve the situation of voltage violation caused by the grid-connection of photovoltaic (PV) system in a distribution network, a bi-level programming model is proposed for battery energy storage system (BESS) deployment. The objective function of inner level programming is to minimize voltage violation, with the power of PV and BESS as the variables. The objective function of outer level programming is to minimize the comprehensive function originated from inner layer programming and all the BESS operating parameters, with the capacity and rated power of BESS as the variables. The differential evolution (DE) algorithm is applied to solve the model. Based on distribution network operation scenarios with photovoltaic generation under multiple alternative output modes, the simulation results of IEEE 33-bus system prove that the deployment strategy of BESS proposed in this paper is well adapted to voltage violation regulation invariable distribution network operation scenarios. It contributes to regulating voltage violation in distribution network, as well as to improve the utilization of PV systems.

A passively controlled appendage deployment system for the San Marco D/L spacecraft

Science.gov (United States)

Lang, W. E.; Frisch, H. P.; Schwartz, D. A.

1984-01-01

The analytical simulation of deployment dynamics of these two axis concepts as well as the evolution of practical designs for the add on deployable inertia boom units is described. With the boom free to swing back in response to Coriolis forces as well as outwards in response to centrifugal forces, the kinematics of motion are complex but admit the possibility of absorbing deployment energy in frictional or other damping devices about the radial axis, where large amplitude motions can occur and where the design envelope allows more available volume. An acceptable range is defined for frictional damping for any given spin rate. Inadequate damping allows boom motions which strike the spacecraft; excessive damping causes the boom to swing out and latch with damaging violence. The acceptable range is a design parameter and must accommodate spin rate tolerance and also the tolerance and repeatability of the damping mechanisms.

Minimizing the Energy Consumption in ‎Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Mohammed Saad Talib

2017-12-01

Full Text Available Energy in Wireless Sensor networks (WSNs represents an essential factor in designing, controlling and operating the sensor networks. Minimizing the consumed energy in WSNs application is a crucial issue for the network effectiveness and efficiency in terms of lifetime, cost and operation. Number of algorithms and protocols were proposed and implemented to decrease the energy consumption. WSNs operate with battery powered sensors. Sensors batteries have not easily rechargeable even though having restricted power. Frequently the network failure occurs due to the sensors energy insufficiency. MAC protocols in WSNs achieved low duty-cycle by employing periodic sleep and wakeup. Predictive Wakeup MAC (PW-MAC protocol was made use of the asynchronous duty cycling. It reduces the consumption of the node energy by allowing the senders to predict the receiver′s wakeup times. The WSN must be applied in an efficient manner to utilize the sensor nodes and their energy to ensure efficient network throughput. Prediction of the WSN lifetime previously to its installation represents a significant concern. To ensure energy efficiency the sensors duty cycles must be adjusted appropriately to meet the network traffic demands. The energy consumed in each node due to its switching between the active and the idle states were also estimated. The sensors are assumed to be randomly deployed. This paper aims to improve the randomly deployed network lifetime by scheduling the effects of transmission, reception and sleep states on the sensor node energy consumption. Results for these states with many performance metrics were also studied and discussed

Intelligent quality function deployment system in concurrent engineering environment

Science.gov (United States)

Lin, Zhihang; Che, Ada

1998-10-01

This paper describes work being undertaken in the development of an intelligent distributed quality function deployment (IDQFD) system, which supports product design team to transfer and deployment the `Voice of Customer' through `House of Quality' into the various stages of product planning, engineering and manufacturing. The requirement modeling of products, the optimization in QFD are indicated. The framework of the system, including QFD tools and platform for distributed collaborative work in QFD, is described. The strategy and methods for the collaboration processing in QFD process are presented. It shows promise for application in practice.

Remotely deployable aerial inspection using tactile sensors

Science.gov (United States)

MacLeod, C. N.; Cao, J.; Pierce, S. G.; Sullivan, J. C.; Pipe, A. G.; Dobie, G.; Summan, R.

2014-02-01

For structural monitoring applications, the use of remotely deployable Non-Destructive Evaluation (NDE) inspection platforms offer many advantages, including improved accessibility, greater safety and reduced cost, when compared to traditional manual inspection techniques. The use of such platforms, previously reported by researchers at the University Strathclyde facilitates the potential for rapid scanning of large areas and volumes in hazardous locations. A common problem for both manual and remote deployment approaches lies in the intrinsic stand-off and surface coupling issues of typical NDE probes. The associated complications of these requirements are obviously significantly exacerbated when considering aerial based remote inspection and deployment, resulting in simple visual techniques being the preferred sensor payload. Researchers at Bristol Robotics Laboratory have developed biomimetic tactile sensors modelled on the facial whiskers (vibrissae) of animals such as rats and mice, with the latest sensors actively sweeping their tips across the surface in a back and forth motion. The current work reports on the design and performance of an aerial inspection platform and the suitability of tactile whisking sensors to aerial based surface monitoring applications.

Evaluation of a Multimedia Intervention for Children and Families Facing Multiple Military Deployments.

Science.gov (United States)

Flittner O'Grady, Allison; Thomaseo Burton, E; Chawla, Neelu; Topp, David; MacDermid Wadsworth, Shelley

2016-02-01

Repeated military deployments have been a common experience for many military families in the past 15 years. While there has been an increase in research and intervention focused on the effects on families of military deployments, much of this work has not focused specifically on the particular needs of young children. Talk, Listen, Connect: Multiple Deployments (TLC-II MD), a multimedia kit designed for home use, is among the first interventions directed toward young children. Created by Sesame Workshop and using popular Sesame Street characters, TLC-II MD was designed to support and equip families with young children with skills to address challenges associated with multiple deployments. This study utilized a randomized experimental design to evaluate the impact of TLC-II MD relative to a control condition using a Sesame Workshop multimedia kit not tailored to military families. Parents in both groups reported that children enjoyed the video overall and watched it repeatedly. Also in both groups, caregivers' depressive symptoms and children's aggressive behaviors declined significantly over time. Caregivers in the test group reported significantly larger increases in comfort discussing the deployment with their child and stronger perceptions that the DVD helped children to cope. Thus, the resilience-oriented materials were helpful to both groups, but those tailored to military families were significantly more likely to be perceived as helpful. Findings offer evidence regarding the ability of multimedia self-administered interventions to assist military families.

Deployment of Wireless Sensor Networks in Crop Storages

DEFF Research Database (Denmark)

Juul, Jakob Pilegaard; Green, Ole; Jacobsen, Rune Hylsberg

2015-01-01

of a wireless sensor network based system that provides continuous, automatic, and up-to-date information on a crop storage, while presenting the data in an easily accessible manner, is also described. The design decisions, challenges, and practical experiences from real-world large scale deployment...

Deploy Nalu/Kokkos algorithmic infrastructure with performance benchmarking.

Energy Technology Data Exchange (ETDEWEB)

Domino, Stefan P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ananthan, Shreyas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Knaus, Robert C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Williams, Alan B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-09-29

The former Nalu interior heterogeneous algorithm design, which was originally designed to manage matrix assembly operations over all elemental topology types, has been modified to operate over homogeneous collections of mesh entities. This newly templated kernel design allows for removal of workset variable resize operations that were formerly required at each loop over a Sierra ToolKit (STK) bucket (nominally, 512 entities in size). Extensive usage of the Standard Template Library (STL) std::vector has been removed in favor of intrinsic Kokkos memory views. In this milestone effort, the transition to Kokkos as the underlying infrastructure to support performance and portability on many-core architectures has been deployed for key matrix algorithmic kernels. A unit-test driven design effort has developed a homogeneous entity algorithm that employs a team-based thread parallelism construct. The STK Single Instruction Multiple Data (SIMD) infrastructure is used to interleave data for improved vectorization. The collective algorithm design, which allows for concurrent threading and SIMD management, has been deployed for the core low-Mach element- based algorithm. Several tests to ascertain SIMD performance on Intel KNL and Haswell architectures have been carried out. The performance test matrix includes evaluation of both low- and higher-order methods. The higher-order low-Mach methodology builds on polynomial promotion of the core low-order control volume nite element method (CVFEM). Performance testing of the Kokkos-view/SIMD design indicates low-order matrix assembly kernel speed-up ranging between two and four times depending on mesh loading and node count. Better speedups are observed for higher-order meshes (currently only P=2 has been tested) especially on KNL. The increased workload per element on higher-order meshes bene ts from the wide SIMD width on KNL machines. Combining multiple threads with SIMD on KNL achieves a 4.6x speedup over the baseline, with

Study of design parameters for minimizing the cost of electricity of tokamak fusion power reactors

International Nuclear Information System (INIS)

Tokimatsu, K.; Yamaji, K.; Katsurai, M.; Okano, K.; Yoshida, T.

1998-01-01

The impact of the design parameters on the cost of electricity (COE) is studied through a parameter survey in order to minimize the COE. Three kinds of operating modes are considered; first stability (FS), second stability (SS) and reversed shear (RS). The COE is calculated by a coupled physics-engineering-cost computer system code. Deuterium-tritium type, 1000 MW(e) at electric bus bar, steady state tokamak reactors with aspect ratios A from 3 to 4.5 are assumed. Several criteria are used for the parameter survey; for example, (a) the thermal to electrical conversion efficiency is assumed to be 34.5% using water as a coolant; (b) the average neutron wall load must not exceed 5 MW/m 2 for plasma major radius R p >5 m; (c) a 2 MeV neutral beam injector (NBI) is applied. It is found that the RS operating mode most minimizes the COE among the three operating modes by reducing the cost of the current drive and the coils and structures. The cost-minimized RS reactor can attain high f bs , high β N and low q 95 at the same time, which results in a short R p of 5.1 m, a low B max of the maximum magnetic toroidal field (TF) of the TF coils of 13 T and a low A of 3.0. It can be concluded that this cost-minimized RS reactor is the most cost-minimized within the frameworks of this study. This cost-minimized RS reactor has two advantages: one is that a B max =13 T TF coil can be made by use of ITER coil technology and the other is that the same cooling technology as that of ITER (water cooling) can be used. (author)

Surveillance of a 2D Plane Area with 3D Deployed Cameras

Directory of Open Access Journals (Sweden)

Yi-Ge Fu

2014-01-01

Full Text Available As the use of camera networks has expanded, camera placement to satisfy some quality assurance parameters (such as a good coverage ratio, an acceptable resolution constraints, an acceptable cost as low as possible, etc. has become an important problem. The discrete camera deployment problem is NP-hard and many heuristic methods have been proposed to solve it, most of which make very simple assumptions. In this paper, we propose a probability inspired binary Particle Swarm Optimization (PI-BPSO algorithm to solve a homogeneous camera network placement problem. We model the problem under some more realistic assumptions: (1 deploy the cameras in the 3D space while the surveillance area is restricted to a 2D ground plane; (2 deploy the minimal number of cameras to get a maximum visual coverage under more constraints, such as field of view (FOV of the cameras and the minimum resolution constraints. We can simultaneously optimize the number and the configuration of the cameras through the introduction of a regulation item in the cost function. The simulation results showed the effectiveness of the proposed PI-BPSO algorithm.

Solar sail deployment experiment

OpenAIRE

Shimose, Shigeru; 下瀬　滋

2006-01-01

Solar Sail move by receiving momentum of photons in sunlight. This paper presents results of some Spin-Stabilized Solar Sail deployment experiment. ISAS has successfully deployed, for the first time in the world, the polyimide Solar Sail taking advantage of centrifugal force in space. Based on this result, the new deployment mechanism is being developed which retracts the 50 m diameter sail.

Sensor Deployment for Air Pollution Monitoring Using Public Transportation System

OpenAIRE

Yu, James J. Q.; Li, Victor O. K.; Lam, Albert Y. S.

2015-01-01

Air pollution monitoring is a very popular research topic and many monitoring systems have been developed. In this paper, we formulate the Bus Sensor Deployment Problem (BSDP) to select the bus routes on which sensors are deployed, and we use Chemical Reaction Optimization (CRO) to solve BSDP. CRO is a recently proposed metaheuristic designed to solve a wide range of optimization problems. Using the real world data, namely Hong Kong Island bus route data, we perform a series of simulations an...

Minimal-Intrusion Traffic Monitoring And Analysis In Mission-Critical Communication Networks

Directory of Open Access Journals (Sweden)

Alberto Domingo Ajenjo

2003-10-01

Full Text Available A good knowledge of expected and actual traffic patterns is an essential tool for network planning, design and operation in deployed, mission-critical applications. This paper describes those needs, and explains the Traffic Monitoring and Analysis Platform (TMAP concept, as developed in support of NATO deployed military headquarters Communications and Information Systems. It shows how a TMAP was deployed to a real NATO exercise, to prove the concept and baseline the traffic needs per application, per user community and per time of day. Then, it analyses the obtained results and derives conclusions on how to integrate traffic monitoring and analysis platforms in future deployments.

Review of Large Spacecraft Deployable Membrane Antenna Structures

Science.gov (United States)

Liu, Zhi-Quan; Qiu, Hui; Li, Xiao; Yang, Shu-Li

2017-11-01

The demand for large antennas in future space missions has increasingly stimulated the development of deployable membrane antenna structures owing to their light weight and small stowage volume. However, there is little literature providing a comprehensive review and comparison of different membrane antenna structures. Space-borne membrane antenna structures are mainly classified as either parabolic or planar membrane antenna structures. For parabolic membrane antenna structures, there are five deploying and forming methods, including inflation, inflation-rigidization, elastic ribs driven, Shape Memory Polymer (SMP)-inflation, and electrostatic forming. The development and detailed comparison of these five methods are presented. Then, properties of membrane materials (including polyester film and polyimide film) for parabolic membrane antennas are compared. Additionally, for planar membrane antenna structures, frame shapes have changed from circular to rectangular, and different tensioning systems have emerged successively, including single Miura-Natori, double, and multi-layer tensioning systems. Recent advances in structural configurations, tensioning system design, and dynamic analysis for planar membrane antenna structures are investigated. Finally, future trends for large space membrane antenna structures are pointed out and technical problems are proposed, including design and analysis of membrane structures, materials and processes, membrane packing, surface accuracy stability, and test and verification technology. Through a review of large deployable membrane antenna structures, guidance for space membrane-antenna research and applications is provided.

EPRI activities in support of new nuclear plant deployment

International Nuclear Information System (INIS)

Mulford, T.

2007-01-01

This paper describes the challenges to new plant deployment in the United States and discusses the role of the Electric Power Research Institute (EPRI) in efforts to address these challenges. These technical challenges include completing remaining design work, licensing review, and standardization required to ensure that new LWRs are a competitive near-term option. The costs for construction, licensing, and operation of new nuclear plants are uncertain and this uncertainty, along with concerns about construction schedule form a financial challenge to investment. Because the new process for licensing nuclear power plants in the United States has not been fully demonstrated, regulatory concerns also serve as a challenge to near-term commitments to build new nuclear power plants. EPRI is working in concert with utilities and vendors to upgrade certified LWR designs and obtain certification of new LWR designs. Specific technical areas being addressed by EPRI projects include updating the Utility Requirements Document (URD), seismic resolution, radiation protection, radioactive waste management, the development of utility planning tools, and staff optimization. EPRI's key on-going project, the New Plant Deployment Program Model (NPDPM), is designed to help prospective and actual new nuclear plant managers and staff to identify schedule and resource requirements from the point of the decision to build a plant through to the start of commercial operation. This model will describe and organize key activities and assess schedule, activity duration, logic relationships and critical path analysis. The new plant licensing and deployment process is a five to ten year activity representing a significant financial investment that requires coordination with federal and state regulators, designers, architect engineers, and numerous other contributing organizations. Planning is crucial to schedule and budget control. EPRI has also supported projects to quantify the environmental

Development and Calibration of a Field-Deployable Microphone Phased Array for Propulsion and Airframe Noise Flyover Measurements

Science.gov (United States)

Humphreys, William M., Jr.; Lockard, David P.; Khorrami, Mehdi R.; Culliton, William G.; McSwain, Robert G.; Ravetta, Patricio A.; Johns, Zachary

2016-01-01

A new aeroacoustic measurement capability has been developed consisting of a large channelcount, field-deployable microphone phased array suitable for airframe noise flyover measurements for a range of aircraft types and scales. The array incorporates up to 185 hardened, weather-resistant sensors suitable for outdoor use. A custom 4-mA current loop receiver circuit with temperature compensation was developed to power the sensors over extended cable lengths with minimal degradation of the signal to noise ratio and frequency response. Extensive laboratory calibrations and environmental testing of the sensors were conducted to verify the design's performance specifications. A compact data system combining sensor power, signal conditioning, and digitization was assembled for use with the array. Complementing the data system is a robust analysis system capable of near real-time presentation of beamformed and deconvolved contour plots and integrated spectra obtained from array data acquired during flyover passes. Additional instrumentation systems needed to process the array data were also assembled. These include a commercial weather station and a video monitoring / recording system. A detailed mock-up of the instrumentation suite (phased array, weather station, and data processor) was performed in the NASA Langley Acoustic Development Laboratory to vet the system performance. The first deployment of the system occurred at Finnegan Airfield at Fort A.P. Hill where the array was utilized to measure the vehicle noise from a number of sUAS (small Unmanned Aerial System) aircraft. A unique in-situ calibration method for the array microphones using a hovering aerial sound source was attempted for the first time during the deployment.

The Long Tail Issue in Large Scale Deployment of Personal Informatics

DEFF Research Database (Denmark)

Cuttone, Andrea; Larsen, Jakob Eg

2014-01-01

We describe the challenges and the open questions arising during the design and deployment of SensibleJournal, a mobile personal informatics system with interactive visualizations of mobility and social interactions based on data acquired from embedded smartphone sensors. The SensibleJournal system...... was evaluated in a large scale (N=136) mobile sensing field study. We report issues in deployment, limitations in user engagement and uptake, and the challenges in measuring the effect of the system....

Financial Incentives to Enable Clean Energy Deployment: Policy Overview and Good Practices

Energy Technology Data Exchange (ETDEWEB)

Cox, Sadie [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-02-24

Financial incentives have been widely implemented by governments around the world to support scaled up deployment of renewable energy and energy efficiency technologies and practices. As of 2015, at least 48 countries have adopted financial incentives to support renewable energy and energy efficiency deployment. Broader clean energy strategies and plans provide a crucial foundation for financial incentives that often complement regulatory policies such as renewable energy targets, standards, and other mandates. This policy brief provides a primer on key financial incentive design elements, lessons from different country experiences, and curated support resources for more detailed and country-specific financial incentive design information.

Supply strategy for SMR deployment

International Nuclear Information System (INIS)

Coccagna, A.F.

2013-01-01

This document provides a description of Babcock and Wilcox's deployment strategy for the mPower™ Small Modular Reactor from the perspective of Supply Chain and Manufacturing. A desirable future state of readiness is described as one which leverages and revitalizes an existing supply chain and manufacturing infrastructure, as well as leveraging an existing workforce of engineering, construction, and project management employees. B and W's mPower™ SMR value proposition offers many desired design and operating advantages to the SMR market. (author)

Core Design and Deployment Strategy of Heavy Water Cooled Sustainable Thorium Reactor

Directory of Open Access Journals (Sweden)

Naoyuki Takaki

2012-08-01

Full Text Available Our previous studies on water cooled thorium breeder reactor based on matured pressurized water reactor (PWR plant technology concluded that reduced moderated core by arranging fuel pins in a triangular tight lattice array and using heavy water as coolant is appropriate for achieving better breeding performance and higher burn-up simultaneously [1–6]. One optimum core that produces 3.5 GW thermal energy using Th-²³³U oxide fuel shows a breeding ratio of 1.07 and averaged burn-up of about 80 GWd/t with long cycle length of 1300 days. The moderator to fuel volume ratio is 0.6 and required enrichment of ²³³U for the fresh fuel is about 7%. The coolant reactivity coefficient is negative during all cycles despite it being a large scale breeder reactor. In order to introduce this sustainable thorium reactor, three-step deployment scenario, with intermediate transition phase between current light water reactor (LWR phase and future sustainer phase, is proposed. Both in transition phase and sustainer phase, almost the same core design can be applicable only by changing fissile materials mixed with thorium from plutonium to ²³³U with slight modification in the fuel assembly design. Assuming total capacity of 60 GWe in current LWR phase and reprocessing capacity of 800 ton/y with further extensions to 1600 ton/y, all LWRs will be replaced by heavy water cooled thorium reactors within about one century then thorium reactors will be kept operational owing to its potential to sustain fissile fuels while reprocessing all spent fuels until exhaustion of massive thorium resource.

Time Domain Equalizer Design Using Bit Error Rate Minimization for UWB Systems

Directory of Open Access Journals (Sweden)

Syed Imtiaz Husain

2009-01-01

Full Text Available Ultra-wideband (UWB communication systems occupy huge bandwidths with very low power spectral densities. This feature makes the UWB channels highly rich in resolvable multipaths. To exploit the temporal diversity, the receiver is commonly implemented through a Rake. The aim to capture enough signal energy to maintain an acceptable output signal-to-noise ratio (SNR dictates a very complicated Rake structure with a large number of fingers. Channel shortening or time domain equalizer (TEQ can simplify the Rake receiver design by reducing the number of significant taps in the effective channel. In this paper, we first derive the bit error rate (BER of a multiuser and multipath UWB system in the presence of a TEQ at the receiver front end. This BER is then written in a form suitable for traditional optimization. We then present a TEQ design which minimizes the BER of the system to perform efficient channel shortening. The performance of the proposed algorithm is compared with some generic TEQ designs and other Rake structures in UWB channels. It is shown that the proposed algorithm maintains a lower BER along with efficiently shortening the channel.

Deployment of hydrogen supply chain for fuel market in 2050: Design and development of a decision support system for scenarios analysis

International Nuclear Information System (INIS)

Patay, E.

2008-07-01

The deployment of a market for hydrogen energy is a new problem, considered by governments, industrialists and scientists to meet global targets of greenhouse gases emissions reduction and to ensure security in energy supply. In this context, the optimization problem of scheduling the deployment until 2050 of the hydrogen supply chain for fuel market throughout a country has been the object of our study. We get support of Air Liquide Company, his experience and experts in production and distribution of industrial hydrogen, to build an approach to the problem meeting the requirements of an industrial context. After defining and characterizing the optimization problem through a systemic analysis of the distribution infrastructure, we proposed a method suited to its resolution. Monte Carlo simulations enabled us to develop cost functions. Then we developed a heuristic algorithm for approximate optimization of these cost functions. Our approach has necessitated the definition of simulation rules, a design of experiment and a regression method, as well as a heuristic algorithm adapted to the structure of the problem. The specification, development and use of software tools have helped to validate the chosen methodology for the optimization of the uncertain problem of our study. The scenario of evolution has created a reference to validate the model and provide some analysis for early studies of deployment. (author)

Gender differences in the effects of deployment-related stressors and pre-deployment risk factors on the development of PTSD symptoms in National Guard Soldiers deployed to Iraq and Afghanistan.

Science.gov (United States)

Polusny, Melissa A; Kumpula, Mandy J; Meis, Laura A; Erbes, Christopher R; Arbisi, Paul A; Murdoch, Maureen; Thuras, Paul; Kehle-Forbes, Shannon M; Johnson, Alexandria K

2014-02-01

Although women in the military are exposed to combat and its aftermath, little is known about whether combat as well as pre-deployment risk/protective factors differentially predict post-deployment PTSD symptoms among women compared to men. The current study assesses the influence of combat-related stressors and pre-deployment risk/protective factors on women's risk of developing PTSD symptoms following deployment relative to men's risk. Participants were 801 US National Guard Soldiers (712 men, 89 women) deployed to Iraq or Afghanistan who completed measures of potential risk/protective factors and PTSD symptoms one month before deployment (Time 1) and measures of deployment-related stressors and PTSD symptoms about 2-3 months after returning from deployment (Time 2). Men reported greater exposure to combat situations than women, while women reported greater sexual stressors during deployment than men. Exposure to the aftermath of combat (e.g., witnessing injured/dying people) did not differ by gender. At Time 2, women reported more severe PTSD symptoms and higher rates of probable PTSD than did men. Gender remained a predictor of higher PTSD symptoms after accounting for pre-deployment symptoms, prior interpersonal victimization, and combat related stressors. Gender moderated the association between several risk factors (combat-related stressors, prior interpersonal victimization, lack of unit support and pre-deployment concerns about life/family disruptions) and post-deployment PTSD symptoms. Elevated PTSD symptoms among female service members were not explained simply by gender differences in pre-deployment or deployment-related risk factors. Combat related stressors, prior interpersonal victimization, and pre-deployment concerns about life and family disruptions during deployment were differentially associated with greater post-deployment PTSD symptoms for women than men. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

How will fourth-generation nuclear systems be deployed?; Comment les systemes nucleaires de 4. generation se deploieront-ils?

Energy Technology Data Exchange (ETDEWEB)

Bonin, B.; Carre, F. [CEA Saclay, Dir. de l' Energie Nucleaire, 91 - Gif sur Yvette (France)

2007-07-01

If it is to be fully consonant with a sustainable development perspective, nuclear energy needs must rely on systems that will ensure the greatest optimization of fissile material utilization, while minimizing production of ultimate waste. Deployment scenarios, for systems of the new generation, remain very much open. (authors)

Customer Focused Product Design Using Integrated Model of Target Costing, Quality Function Deployment and Value Engineering

Directory of Open Access Journals (Sweden)

Hossein Rezaei Dolatabadi

2013-01-01

Full Text Available Target costing by integrating customer requirements, technical attributes and cost information into the product design phase and eliminating the non-value added functions, plays a vital role in different phases of the product life cycle. Quality Function Deployment (QFD and Value Engineering (VE are two techniques which can be used for applying target costing, successfully. The purpose of this paper is to propose an integrated model of target costing, QFD and VE to explore the role of target costing in managing product costs while promoting quality specifications meeting customers’ needs. F indings indicate that the integration of target costing, QFD and VE is an essential technique in managing the costs of production process. Findings also imply that integration of the three techniques provides a competitive cost advantage to companies.

Modeling and analysis of a large deployable antenna structure

Science.gov (United States)

Chu, Zhengrong; Deng, Zongquan; Qi, Xiaozhi; Li, Bing

2014-02-01

One kind of large deployable antenna (LDA) structure is proposed by combining a number of basic deployable units in this paper. In order to avoid vibration caused by fast deployment speed of the mechanism, a braking system is used to control the spring-actuated system. Comparisons between the LDA structure and a similar structure used by the large deployable reflector (LDR) indicate that the former has potential for use in antennas with up to 30 m aperture due to its lighter weight. The LDA structure is designed to form a spherical surface found by the least square fitting method so that it can be symmetrical. In this case, the positions of the terminal points in the structure are determined by two principles. A method to calculate the cable network stretched on the LDA structure is developed, which combines the original force density method and the parabolic surface constraint. Genetic algorithm is applied to ensure that each cable reaches a desired tension, which avoids the non-convergence issue effectively. We find that the pattern for the front and rear cable net must be the same when finding the shape of the rear cable net, otherwise anticlastic surface would generate.

Fusion Power Deployment

International Nuclear Information System (INIS)

Schmidt, J.A.; Ogden, J.M.

2002-01-01

Fusion power plants could be part of a future portfolio of non-carbon dioxide producing energy supplies such as wind, solar, biomass, advanced fission power, and fossil energy with carbon dioxide sequestration. In this paper, we discuss key issues that could impact fusion energy deployment during the last half of this century. These include geographic issues such as resource availability, scale issues, energy storage requirements, and waste issues. The resource needs and waste production associated with fusion deployment in the U.S. should not pose serious problems. One important feature of fusion power is the fact that a fusion power plant should be locatable within most local or regional electrical distribution systems. For this reason, fusion power plants should not increase the burden of long distance power transmission to our distribution system. In contrast to fusion power, regional factors could play an important role in the deployment of renewable resources such as wind, solar and biomass or fossil energy with CO2 sequestration. We examine the role of these regional factors and their implications for fusion power deployment

TQM and lean strategy deployment in Italian hospitals.

Science.gov (United States)

Chiarini, Andrea; Baccarani, Claudio

2016-10-03

Purpose This paper aims to contribute to the debate concerning total quality management (TQM)-Lean strategy in public healthcare by analyzing the deployment path for implementation, the possible benefits that can be achieved and the encountered pitfalls. Design/methodology/approach Three case studies are drawn from three large Italian hospitals with more than 500 beds each and structured with many departments. The hospitals are located in Tuscany, Italy. These three hospitals have embraced TQM and Lean, starting from strategic objectives and their deployment. At the same time, they have also implemented many TQM-Lean tools. The case studies are based on interviews held with four managers in each of these three public hospitals. Findings Results from the interviews show that there is a specific deployment path for TQM-Lean implementation. The hospitals have also achieved benefits linked to patient satisfaction and improved organizational performances. Problems related to organizational and cultural issues, such as senior managers' commitment, staff management, manufacturing culture and tools adaptation, could affect the benefits. Research limitations/implications The research has been carried out in just three Italian public hospitals. Hence, similar investigations could be managed in other countries. Researchers could also use a larger sample and investigate these issues by means of quantitative inquiry. Practical implications Practitioners could try to apply the deployment path revealed by these case studies in other public and private hospitals. Originality/value The results of this research show that there is a specific, new deployment path for implementing TQM-Lean strategy in some public hospitals.

Multi-functional hinge equipped with a magneto-rheological rotary damper for solar array deployment system

Science.gov (United States)

Wen, Mingfu; Yu, Miao; Fu, Jie; Wu, Zhengzhong

2015-02-01

This article describes the design and simulation of a novel multi-functional hinge equipped with a rotary magnetorheological damper for solar array deployment system, which is comprised of a hinge, an angular sensor, a positioning and locking mechanism and a rotary damper. In order to achieve the compact design in structure, some components were reused in different function modules. It's the first to use magnet-rheological fluid (MRF) to dissipate the energy in solar array deployment system. The main advantage in using MR rotary damper instead of a viscous fluid rotary damper is that the damping force of MR damper can be adjusted according to the external magnetic field environment excited. A mechanic model was built and the structure design was focused on the MR rotary damper, a damping force model of this damper is deduced based on hydromechanics with Bingham plastic constitutive model. A simulation of deployment motion was taken to validate the motion sequence of various components during the unfolding and locking process. It can be obtained that a constant damping coefficient can hardly balance the different performance of solar deployment system, then a simulation of the proposed deployment system equipped with rotary MR damper was carried out. According to the simulation, it can be obtained that the terminal velocity decreased by 75.81% and the deployment time decreased by 72.37% compared with a given constant damping coefficients. Therefore, the proposed new type of rotary damper can reach a compromise with different performance utilizing an on-off control strategy.

Deployment Effects of Marin Renewable Energy Technologies

Energy Technology Data Exchange (ETDEWEB)

Brian Polagye; Mirko Previsic

2010-06-17

Given proper care in siting, design, deployment, operation and maintenance, marine and hydrokinetic technologies could become one of the more environmentally benign sources of electricity generation. In order to accelerate the adoption of these emerging hydrokinetic and marine energy technologies, navigational and environmental concerns must be identified and addressed. All developing hydrokinetic projects involve a wide variety of stakeholders. One of the key issues that site developers face as they engage with this range of stakeholders is that many of the possible conflicts (e.g., shipping and fishing) and environmental issues are not well-understood, due to a lack of technical certainty. In September 2008, re vision consulting, LLC was selected by the Department of Energy (DoE) to apply a scenario-based approach to the emerging wave and tidal technology sectors in order to evaluate the impact of these technologies on the marine environment and potentially conflicting uses. The project’s scope of work includes the establishment of baseline scenarios for wave and tidal power conversion at potential future deployment sites. The scenarios will capture variations in technical approaches and deployment scales to properly identify and characterize environmental impacts and navigational effects. The goal of the project is to provide all stakeholders with an improved understanding of the potential effects of these emerging technologies and focus all stakeholders onto the critical issues that need to be addressed. This groundwork will also help in streamlining siting and associated permitting processes, which are considered key hurdles for the industry’s development in the U.S. today. Re vision is coordinating its efforts with two other project teams funded by DoE which are focused on regulatory and navigational issues. The results of this study are structured into three reports: 1. Wave power scenario description 2. Tidal power scenario description 3. Framework for

13-Helix folding of a β/γ-peptide manifold designed from a "minimal-constraint" blueprint.

Science.gov (United States)

Grison, Claire M; Robin, Sylvie; Aitken, David J

2016-06-14

A bottom-up design rationale was adopted to devise β/γ-peptide foldamer manifolds which would adopt preferred 13-helix conformations, relying on minimal steric imposition brought by the constituent amino acid residues. In this way, a well-defined 13-helix conformer was revealed for short oligomers of trans-2-aminocyclobutanecarboxylic acid and γ(4)-amino acids in alternation, which gave good topological superposition upon an α-helix motif.

Shape memory alloy fixator system for suturing tissue in minimal access surgery.

Science.gov (United States)

Xu, W; Frank, T G; Stockham, G; Cuschieri, A

1999-01-01

A new technique for suturing human tissue is described in which tissue closure is achieved by means of small fixators made from shape memory alloy. The aim of the development is to provide an alternative to thread suturing in minimal access surgery, which is quicker and requires less skill to achieve the required suturing quality. The design of the fixators is described in terms of the thermal shape recovery of shape memory alloy and a novel form of finite element analysis, which uses a nonlinear elastic element for the material property. Thermal analysis of the fixators and surrounding tissue is used to predict the temperature distribution during and after the application of electric current heating. This was checked in an in vitro experiment, which confirmed that deployment caused no detectable collateral damage to surrounding tissue. In vivo animal studies on the use of the shape memory alloy fixator for suturing tissue are ongoing to establish safety and healing effects.

Energy storage deployment and innovation for the clean energy transition

Science.gov (United States)

Kittner, Noah; Lill, Felix; Kammen, Daniel M.

2017-09-01

The clean energy transition requires a co-evolution of innovation, investment, and deployment strategies for emerging energy storage technologies. A deeply decarbonized energy system research platform needs materials science advances in battery technology to overcome the intermittency challenges of wind and solar electricity. Simultaneously, policies designed to build market growth and innovation in battery storage may complement cost reductions across a suite of clean energy technologies. Further integration of R&D and deployment of new storage technologies paves a clear route toward cost-effective low-carbon electricity. Here we analyse deployment and innovation using a two-factor model that integrates the value of investment in materials innovation and technology deployment over time from an empirical dataset covering battery storage technology. Complementary advances in battery storage are of utmost importance to decarbonization alongside improvements in renewable electricity sources. We find and chart a viable path to dispatchable US$1 W-1 solar with US$100 kWh-1 battery storage that enables combinations of solar, wind, and storage to compete directly with fossil-based electricity options.

The Health and Safety Benefits of New Technologies in Mining: A Review and Strategy for Designing and Deploying Effective User-Centred Systems

Directory of Open Access Journals (Sweden)

Tim Horberry

2012-10-01

Full Text Available Mining is currently experiencing a rapid growth in the development and uptake of automation and other new technologies (such as collision detection systems; however, they are often developed from a technology-centred perspective that does not explicitly consider the end-user. This paper first presents a review of the technologies currently available (or near-market and the likely human factors issues associated with them. The second part of the paper presents a potential long term strategy for research and development that aims to maximise the safety and health benefits for operators of such new technologies. The strategy includes a four stage research and development process, this covers: better understanding the needs for technology, user requirements and risk/cost analysis; human element design, procurement and deployment processes; evaluation and verification of the strategy; and dissemination of it to relevant stakeholders (including equipment manufacturers, mine site purchasers and regulators. The paper concludes by stressing the importance of considering the human element with respect to new mining technologies and the likely benefits of adopting the type of strategy proposed here. The overall vision is for mining to become safer and healthier through effective user-centred design and deployment of new technologies that serve both operator needs and the demands of the workplace.

Deployment Plan for Small Roving Annulus Inspection Vehicle

International Nuclear Information System (INIS)

Minichan, R.

2002-01-01

The Small Roving Annulus Inspection Vehicle (SRAIV) is a modified commercially available wall crawler designed to supplement the In-Service Inspection (ISI) of Savannah River Site (SRS) Waste tanks. The SRAIV provides an improved capability to achieve a more complete inspection of the tank walls than existing methods. The SRAIV will be deployed through annulus risers in the tank to gain access to tank walls requiring inspection. The SRAIV will be deployed using a manually operated deployment pole and will be coupled to the wall using permanent magnet wheels. Navigation will be performed from the remote console where pictorial views can be displayed from the on-board cameras. The unit will incorporate multiple UT transducers for traditional weld examination. In addition, a specially developed Tandem Synthetic Aperture Focusing Technique (TSAFT) UT scanning bridge can be attached to provide further investigation of the knuckle region while the vehicle remains on the vertical surface of the tank wall. In summary, the SRAIV will provide features that enhance and expand the capability of the SRS ISI program

Minimization of number of setups for mounting machines

Energy Technology Data Exchange (ETDEWEB)

Kolman, Pavel; Nchor, Dennis; Hampel, David [Department of Statistics and Operation Analysis, Faculty of Business and Economics, Mendel University in Brno, Zemědělská 1, 603 00 Brno (Czech Republic); Žák, Jaroslav [Institute of Technology and Business, Okružní 517/10, 370 01 České Budejovice (Czech Republic)

2015-03-10

The article deals with the problem of minimizing the number of setups for mounting SMT machines. SMT is a device used to assemble components on printed circuit boards (PCB) during the manufacturing of electronics. Each type of PCB has a different set of components, which are obligatory. Components are placed in the SMT tray. The problem consists in the fact that the total number of components used for all products is greater than the size of the tray. Therefore, every change of manufactured product requires a complete change of components in the tray (i.e., a setup change). Currently, the number of setups corresponds to the number of printed circuit board type. Any production change affects the change of setup and stops production on one shift. Many components occur in more products therefore the question arose as to how to deploy the products into groups so as to minimize the number of setups. This would result in a huge increase in efficiency of production.

Development and Deployment Strategy for a Small Advanced Light Water Reactor

International Nuclear Information System (INIS)

Modro, S. Michael; Reith, Raymond; Babka, Pierre

2002-01-01

This paper discusses development and deployment strategies for the modular Multi-Application Small Light Water Reactor (MASLWR). Modularity, small size, capability to transport whole modules including containment on road or by rail, simplicity and safety of this reactor allows innovative deployment strategies for a variety of applications. A larger plant may be constructed of many independent power generation units. The multi-module plant is intended to be operated as a base-load plant. Each reactor is to be operated at full load. However, in response to changes in power demand individual units can brought on line or shut down. A larger plant can be built in small increments to match the power demand balancing capital commitments with revenues from sales of electricity. Also, an unplanned shutdown of a reactor only affects a relatively small portion of the total plant capacity. Simplification of MASLWR design and extensive use of modularization coupled with factory fabrication will result in improved productivity of fieldwork and improved quality achieved in a factory environment. The initial MASLWR design concept development has been completed under the U.S. DOE (Department of Energy) Nuclear Energy Research Initiative (NERI) project. This paper discusses a strategy for developing and deploying a MASLWR plant by 2015. This schedule is realistic because the plant design relies on existing industrial experience and manufacturing capabilities. The development strategy consists of the following elements: concept confirmation through testing (under the NERI program a scaled integral test facility has been constructed and initial testing performed), design concept optimization, and design certification based on prototype testing. (authors)

An Action Design Research on development and deployment of a computer-based group discussion support tool for achieving consensus and culture change at an educational institution

NARCIS (Netherlands)

Lee Mui Suan, Jaclyn; van Hillegersberg, Jos; Kumar, Kuldeep

2015-01-01

Organisational culture change is a long and complex process that typically takes years to complete and has a very low success rate. This project addresses the problem by the proposed use of an Action Design Research Methodology to build and deploy an IT artifact named Organisational Culture

Towards Clinically Optimized MRI-guided Surgical Manipulator for Minimally Invasive Prostate Percutaneous Interventions: Constructive Design*

Science.gov (United States)

Eslami, Sohrab; Fischer, Gregory S.; Song, Sang-Eun; Tokuda, Junichi; Hata, Nobuhiko; Tempany, Clare M.; Iordachita, Iulian

2013-01-01

This paper undertakes the modular design and development of a minimally invasive surgical manipulator for MRI-guided transperineal prostate interventions. Severe constraints for the MRI-compatibility to hold the minimum artifact on the image quality and dimensions restraint of the bore scanner shadow the design procedure. Regarding the constructive design, the manipulator kinematics has been optimized and the effective analytical needle workspace is developed and followed by proposing the workflow for the manual needle insertion. A study of the finite element analysis is established and utilized to improve the mechanism weaknesses under some inevitable external forces to ensure the minimum structure deformation. The procedure for attaching a sterile plastic drape on the robot manipulator is discussed. The introduced robotic manipulator herein is aimed for the clinically prostate biopsy and brachytherapy applications. PMID:24683502

Deployable reflector configurations. [for space telescope

Science.gov (United States)

Meinel, A. B.; Meinel, M. P.; Woolf, N. J.

1983-01-01

Both the theoretical reasons for considering a non-circular format for the Large Deployable Reflector, and a potentially realizable concept for such a device, are discussed. The optimum systems for diffraction limited telescopes with incoherent detection have either a single filled aperture, or two such apertures as an interferometer to synthesize a larger aperture. For a single aperture of limited area, a reflector in the form of a slot can be used to give increased angular resolution. It is shown how a 20 x 8 meter telescope can be configured to fit the Space Shuttle bay, and deployed with relatively simple operations. The relationship between the sunshield design and the inclination of the orbit is discussed. The possible use of the LDR as a basic module to permit the construction of supergiant space telescopes and interferometers both for IR/submm studies and for the entire ultraviolet through mm wave spectral region is discussed.

Deployment, Mental Health Problems, Suicidality, and Use of Mental Health Services Among Military Personnel.

Science.gov (United States)

Chu, Carol; Stanley, Ian H; Hom, Melanie A; Lim, Ingrid C; Joiner, Thomas E

2016-01-01

Following deployment, soldiers may struggle to cope with the after-effects of combat service and experience increased suicidality. Therefore, connection to mental health services is vital. Research regarding the relationship between deployment, suicidality, and mental health connections has been equivocal, with some studies finding a link between deployment history and mental health outcomes, and others not. The purpose of this study was to examine the effects of military deployment on mental health and service utilization outcomes using a longitudinal design. Deployment history, mental health visits, symptoms of suicidality, and various mental health outcomes were assessed in a sample of 1,566 Army recruiters at study entry and 18-months follow-up. Deployment history was positively associated with mental health visits, number of major depressive episodes, and acquired capability for suicide at baseline; however, no significant relationship between deployment, mental health visits, and any other suicide or mental health-related outcomes emerged at baseline or follow-up. Findings suggest a disconnection from mental health services among military personnel. Implications for treatment and suicide prevention efforts among military personnel are discussed.

Security-by-Experiment: Lessons from Responsible Deployment in Cyberspace.

Science.gov (United States)

Pieters, Wolter; Hadžiosmanović, Dina; Dechesne, Francien

2016-06-01

Conceiving new technologies as social experiments is a means to discuss responsible deployment of technologies that may have unknown and potentially harmful side-effects. Thus far, the uncertain outcomes addressed in the paradigm of new technologies as social experiments have been mostly safety-related, meaning that potential harm is caused by the design plus accidental events in the environment. In some domains, such as cyberspace, adversarial agents (attackers) may be at least as important when it comes to undesirable effects of deployed technologies. In such cases, conditions for responsible experimentation may need to be implemented differently, as attackers behave strategically rather than probabilistically. In this contribution, we outline how adversarial aspects are already taken into account in technology deployment in the field of cyber security, and what the paradigm of new technologies as social experiments can learn from this. In particular, we show the importance of adversarial roles in social experiments with new technologies.

Novel large deployable antenna backing structure concepts for foldable reflectors

Science.gov (United States)

Fraux, V.; Lawton, M.; Reveles, J. R.; You, Z.

2013-12-01

This paper describes a number of large deployable antenna (LDA) reflector structure concepts developed at EnerSys-ABSL. Furthermore, EnerSys-ABSL has confirmed the desire to build a breadboard demonstrator of a backing deployable structure for a foldable reflector in the diameter range of 4-9 m. As part of this project EnerSys-ABSL has explored five novel deployable structure concepts. This paper presents the top level definition of these concepts together with the requirements considered in the design and selection of the preferred candidate. These new concepts are described and then compared through a trade-off analysis to identify the most suitable concept that EnerSys-ABSL would like to consider for the breadboard demonstrator. Finally, the kinematics of the chosen concept is described in more detail and future steps in the development process are highlighted.

Deployable Laboratory Applications of Nano- and Bio-Technology (Applications de nanotechnologie et biotechnologie destinees a un laboratoire deployable)

Science.gov (United States)

2014-10-01

specialists in hygiene, microbiology , epidemiology or veterinary epidemiology; 3 laboratory technicians and 4 engineers. Designation of special...Transportable Microbiology Laboratory 3-1 3.1 Challenges and Issues 3-1 3.2 Objectives 3-1 3.3 Responses 3-1 3.3.1 Constitution 3-1 3.3.2 Deployment 3-3 3.4...Bundeswehr Institute of Microbiology Neuherbergstrasse 11 80937 Munich GERMANY Email: Romanwoelfel@bundeswehr.org viii STO-TR-HFM-177

An Application of Green Quality Function Deployment to Designing an Air Conditioner

OpenAIRE

Peetam Kumar Dehariya; Dr. Devendra Singh Verma

2015-01-01

The paper tackles a systematic and operational approach to Green Quality Function Deployment (GQFD), a customer oriented survey based quality management system with regular improvement in product development. GQFD shows balance between product development and environmental protection. GQFD is not used to determine their attributes and their levels. GQFD captures what product developers “think” would best satisfy customer needs considering Environmental factor. This research used A...

Minimally invasive strabismus surgery versus paralimbal approach: A randomized, parallel design study is minimally invasive strabismus surgery worth the effort?

Directory of Open Access Journals (Sweden)

Richa Sharma

2014-01-01

Full Text Available Introduction : Minimal access surgery is common in all fields of medicine. We compared a new minimally invasive strabismus surgery (MISS approach with a standard paralimbal strabismus surgery (SPSS approach in terms of post-operative course. Materials and Methods: This parallel design study was done on 28 eyes of 14 patients, in which one eye was randomized to MISS and the other to SPSS. MISS was performed by giving two conjunctival incisions parallel to the horizontal rectus muscles; performing recession or resection below the conjunctival strip so obtained. We compared post-operative redness, congestion, chemosis, foreign body sensation (FBS, and drop intolerance (DI on a graded scale of 0 to 3 on post-operative day 1, at 2-3 weeks, and 6 weeks. In addition, all scores were added to obtain a total inflammatory score (TIS. Statistical Analysis: Inflammatory scores were analyzed using Wilcoxon′s signed rank test. Results: On the first post-operative day, only FBS (P = 0.01 and TIS (P = 0.04 showed significant difference favoring MISS. At 2-3 weeks, redness (P = 0.04, congestion (P = 0.04, FBS (P = 0.02, and TIS (P = 0.04 were significantly less in MISS eye. At 6 weeks, only redness (P = 0.04 and TIS (P = 0.05 were significantly less. Conclusion: MISS is more comfortable in the immediate post-operative period and provides better cosmesis in the intermediate period.

Part 8. Deployment considerations

International Nuclear Information System (INIS)

Dance, K.D.; Chang, Y.I.; Daly, T.A.

1980-01-01

This report addresses considerations of fast breeder reactor development and deployment from a national perspective. Nations vary greatly in their expertise and interest relative to nuclear power, and hence a single set of steps to be taken by a nation in decision-making on breeder development and deployment cannot be presented. The approach taken in this report is to present discussions on key factors influencing the breeder development and deployment decisions, especially in non-breeder nations, by drawing upon historical perspectives of the Light Water Reactor for comparison

Comparing post-deployment mental health services utilization in soldiers deployed to Balkan, Iraq and Afghanistan

DEFF Research Database (Denmark)

Madsen, T; Sadowa Vedtofte, M; Nordentoft, M

2017-01-01

OBJECTIVE: Insight on how different missions have impacted rates of mental health service (MHS) utilization is unexplored. We compared postdeployment MHS utilization in a national cohort of first-time deployed to missions in Balkan, Iraq, and Afghanistan respectively. METHODS: A prospective...... national cohort study of 13 246 first-time deployed in the period 1996 through 2012 to missions in Balkan area, Iraq, or Afghanistan respectively. Soldiers 'MHS utilization was also compared with a 5:1 sex-, age-, and calendar year-matched never-deployed background population. Postdeployment utilization...... of psychotropics. RESULTS: Utilizing of psychiatric outpatient services and psychotropics was significantly higher in first-time deployed to Iraq and Afghanistan compared with deployed to Balkan. However, the rate of postdeployment admission to psychiatric hospital did not differ between missions. Postdeployment...

Minimization of cogging torque in permanent magnet motors by teeth pairing and magnet arc design using genetic algorithm

International Nuclear Information System (INIS)

Eom, J.-B.; Hwang, S.-M.; Kim, T.-J.; Jeong, W.-B.; Kang, B.-S.

2001-01-01

Cogging torque is often a principal source of vibration and acoustic noise in high precision spindle motor applications. In this paper, cogging torque is analytically calculated using energy method with Fourier series expansion. It shows that cogging torque is effectively minimized by controlling airgap permeance function with teeth pairing design, and by controlling flux density function with magnet arc design. For an optimization technique, genetic algorithm is applied to handle trade-off effects of design parameters. Results show that the proposed method can reduce the cogging torque effectively

What pre-deployment and early post-deployment factors predict health function after combat deployment?: a prospective longitudinal study of Operation Enduring Freedom (OEF)/Operation Iraqi Freedom (OIF) soldiers.

Science.gov (United States)

McAndrew, Lisa M; D'Andrea, Elizabeth; Lu, Shou-En; Abbi, Bhavna; Yan, Grace W; Engel, Charles; Quigley, Karen S

2013-04-30

Physical and mental function are strong indicators of disability and mortality. OEF/OIF Veterans returning from deployment have been found to have poorer function than soldiers who have not deployed; however the reasons for this are unknown. A prospective cohort of 790 soldiers was assessed both pre- and immediately after deployment to determine predictors of physical and mental function after war. On average, OEF/OIF Veterans showed significant declines in both physical (t=6.65, pfunction (t=7.11, pdeployment function, poorer physical function after deployment was associated with older age, more physical symptoms, blunted systolic blood pressure reactivity and being injured. After controlling for pre-deployment function, poorer mental function after deployment was associated with younger age, lower social desirability, lower social support, greater physical symptoms and greater PTSD symptoms. Combat deployment was associated with an immediate decline in both mental and physical function. The relationship of combat deployment to function is complex and influenced by demographic, psychosocial, physiological and experiential factors. Social support and physical symptoms emerged as potentially modifiable factors.

iPad in the Enterprise Developing and Deploying Business Applications

CERN Document Server

Clevenger, Nathan

2011-01-01

Discover how to plan, design, develop, and deploy iPad apps for the enterprise Having taken the enterprise by storm, iPads are now in the hands of workers in virtually every level of companies in almost every industry. But using iPad apps in the enterprise is more complex than simply clicking an icon from the App Store. It presents unique challenges around software development, system integration, information security, application deployment, and device management. That's where this book comes in. iPhone Life Enterprise Editor and veteran mobile consultant Nathan Clevenger presents a guide for

AREVA HTR concept for near-term deployment

Energy Technology Data Exchange (ETDEWEB)

Lommers, L.J., E-mail: lewis.lommers@areva.com [AREVA Inc., 2101 Horn Rapids Road, Richland, WA 99354 (United States); Shahrokhi, F. [AREVA Inc., Lynchburg, VA (United States); Mayer, J.A. [AREVA Inc., Marlborough, MA (United States); Southworth, F.H. [AREVA Inc., Lynchburg, VA (United States)

2012-10-15

This paper introduces AREVA's High Temperature Reactor (HTR) steam cycle concept for near-term industrial deployment. Today, nuclear power primarily impacts only electricity generation. The process heat and transportation fuel sectors are completely dependent on fossil fuels. In order to impact this energy sector as rapidly as possible, AREVA has focused its HTR development effort on the steam cycle HTR concept. This reduces near-term development risk and minimizes the delay before a useful contribution to this sector of the energy economy can be realized. It also provides a stepping stone to longer term very high temperature concepts which might serve additional markets. A general description of the current AREVA steam cycle HTR concept is provided. This concept provides a flexible system capable of serving a variety of process heat and cogeneration markets in the near-term.

AREVA HTR concept for near-term deployment

International Nuclear Information System (INIS)

Lommers, L.J.; Shahrokhi, F.; Mayer, J.A.; Southworth, F.H.

2012-01-01

This paper introduces AREVA's High Temperature Reactor (HTR) steam cycle concept for near-term industrial deployment. Today, nuclear power primarily impacts only electricity generation. The process heat and transportation fuel sectors are completely dependent on fossil fuels. In order to impact this energy sector as rapidly as possible, AREVA has focused its HTR development effort on the steam cycle HTR concept. This reduces near-term development risk and minimizes the delay before a useful contribution to this sector of the energy economy can be realized. It also provides a stepping stone to longer term very high temperature concepts which might serve additional markets. A general description of the current AREVA steam cycle HTR concept is provided. This concept provides a flexible system capable of serving a variety of process heat and cogeneration markets in the near-term.

Deploying Renewables: Principles for Effective Policies. Executive Summary [Russian Version

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

Renewable energy can play a fundamental role in tackling climate change, environmental degradation and energy security. As these challenges have become ever more pressing, governments and markets are seeking innovative solutions. Yet, what are the key factors that will determine the success of renewable energy policies? How can current policies be improved to encourage greater deployment of renewables? What impact can more effective policies have on renewables’ share in the future global energy mix and how soon? Deploying Renewables: Principles for Effective Policies addresses these questions. Responding to the Gleneagles G8 call for a clean and secure energy future, it highlights key policy tools to fast-track renewables into the mainstream. This analysis illustrates good practices by applying the combined metrics of effectiveness and efficiency to renewable energy policies in the electricity, heating and transport sectors. It highlights significant barriers to accelerating renewables penetration, and argues that the great potential of renewables can be exploited much more rapidly and to a much larger extent if good practices are adopted. Carefully designed policy frameworks, customised to support technologies at differing stages of maturity, will deliver a strong portfolio of renewable energy technologies. Deploying Renewables: Principles for Effective Policies provides recommendations on key principles for policy design as a template for decision makers.

Application of quality function deployment for designing and developing a curriculum for Industrial Engineering at Prince of Songkla University

Directory of Open Access Journals (Sweden)

Nirachara Boonyanuwat

2008-05-01

Full Text Available A Quality Function Deployment (QFD technique is used to design a curriculum for Industrial Engineering (IE at Prince of Songkla University (PSU. This paper shows a systematical step-by-step application of the QFD. This analysis focuses both on external evaluators of the university, companies that hire graduates and students’ parents, and internal evaluators of the university, the student themselves and faculty. Survey data from 232 stakeholders were used in the QFD analysis in order to identify the requirements most valued by them. Results indicate that the stakeholders are looking for the graduates’ abilities in the area of productivity improvement, knowledge application, production planning and control, quality management and control, and manufacturing management. Further, the QFD is used to translate the key requirements into an effective curriculum. It can be concluded that the QFD is a useful tool for designing a curriculum for higher educational institutions.

Quality Function Deployment for Large Systems

Science.gov (United States)

Dean, Edwin B.

1992-01-01

Quality Function Deployment (QFD) is typically applied to small subsystems. This paper describes efforts to extend QFD to large scale systems. It links QFD to the system engineering process, the concurrent engineering process, the robust design process, and the costing process. The effect is to generate a tightly linked project management process of high dimensionality which flushes out issues early to provide a high quality, low cost, and, hence, competitive product. A pre-QFD matrix linking customers to customer desires is described.

Design Minimalism in Robotics Programming

Directory of Open Access Journals (Sweden)

Anthony Cowley

2008-11-01

Full Text Available With the increasing use of general robotic platforms in different application scenarios, modularity and reusability have become key issues in effective robotics programming. In this paper, we present a minimalist approach for designing robot software, in which very simple modules, with well designed interfaces and very little redundancy can be connected through a strongly typed framework to specify and execute different robotics tasks.

Design Minimalism in Robotics Programming

Directory of Open Access Journals (Sweden)

Anthony Cowley

2006-03-01

Full Text Available With the increasing use of general robotic platforms in different application scenarios, modularity and reusability have become key issues in effective robotics programming. In this paper, we present a minimalist approach for designing robot software, in which very simple modules, with well designed interfaces and very little redundancy can be connected through a strongly typed framework to specify and execute different robotics tasks.

Determining the need for improvement of infant incubator design with quality function deployment

Science.gov (United States)

Tarigan, U.; Ginting, R.; Siregar, I.

2018-02-01

A Newborns need particular attention because it takes time to adapt to the outside world. In accordance with the standard post-neonatal procedures, newborns should be incorporated into the incubator within a specified period of time according to the infant’s health level. Infant incubator as a medical device used to care for newborns, often get complaints from doctors and child nurses. The complaint indicates consumer dissatisfaction with incubator products in the hospital. Broadly speaking, objection against infant incubators lie in inappropriate designs. To overcome these complaints the researchers apply the method of Quality Function Deployment to determine the characteristics of priority techniques in accordance with the wishes of consumers with it. The primary focus of QFD is to engage customers in the product development process as early as possible, which their needs and desires serve as the starting point of the QFD process. Therefore, QFD is called the voice of customer. The underlying philosophy is that customers are not always satisfied with a product even though the product has been perfectly produced. The results show that the category used as a priority improvement is the additional function of the oxygen cylinder and the size of the door hole. QFD phase one produces technical characteristics of Ergonomy, Features and Cost as critical part determinants.

Design and deployment of an elastic network test-bed in IHEP data center based on SDN

Science.gov (United States)

Zeng, Shan; Qi, Fazhi; Chen, Gang

2017-10-01

High energy physics experiments produce huge amounts of raw data, while because of the sharing characteristics of the network resources, there is no guarantee of the available bandwidth for each experiment which may cause link congestion problems. On the other side, with the development of cloud computing technologies, IHEP have established a cloud platform based on OpenStack which can ensure the flexibility of the computing and storage resources, and more and more computing applications have been deployed on virtual machines established by OpenStack. However, under the traditional network architecture, network capability can’t be required elastically, which becomes the bottleneck of restricting the flexible application of cloud computing. In order to solve the above problems, we propose an elastic cloud data center network architecture based on SDN, and we also design a high performance controller cluster based on OpenDaylight. In the end, we present our current test results.

Dynamic analysis of the large deployable reflector

Science.gov (United States)

Calleson, Robert E.; Scott, A. Don

1987-01-01

The Large Deployable Reflector (LDR) is to be an astronomical observatory orbiting above Earth's obscuring atmosphere and operating in the spectral range between 30 microns and 1000 microns wavelength. The LDR will be used to study such astronomical phenomena as stellar and galactic formation, cosmology, and planetary atmospheres. The LDR will be the first observatory to be erected and assembled in space. This distinction brings with it several major technological challenges such as the development of ultra-lightweight deployable mirrors, advanced mirror fabrication techniques, advanced structures, and control of vibrations due to various sources of excitation. The purpose of this analysis is to provide an assessment of the vibrational response due to secondary mirror chopping and LDR slewing. The dynamic response of two 20-m LDR configurations was studied. Two mirror support configurations were investigated for the Ames concept, the first employs a six-strut secondary mirror support structure, while the second uses a triple-bipod support design. All three configurations were modeled using a tetrahedral truss design for the primary mirror support structure. Response resulting from secondary mirror chopping was obtained for the two Ames configurations, and the response of the primary mirror from slewing was obtained for all three configurations.

Design and deployment of autoclave pressure vessels for the portable deep-sea drill rig MeBo (Meeresboden-Bohrgerät)

Science.gov (United States)

Pape, Thomas; Hohnberg, Hans-Jürgen; Wunsch, David; Anders, Erik; Freudenthal, Tim; Huhn, Katrin; Bohrmann, Gerhard

2017-11-01

Pressure barrels for sampling and preservation of submarine sediments under in situ pressure with the robotic sea-floor drill rig MeBo (Meeresboden-Bohrgerät) housed at the MARUM (Bremen, Germany) were developed. Deployments of the so-called MDP (MeBo pressure vessel) during two offshore expeditions off New Zealand and off Spitsbergen, Norway, resulted in the recovery of sediment cores with pressure stages equaling in situ hydrostatic pressure. While initially designed for the quantification of gas and gas-hydrate contents in submarine sediments, the MDP also allows for analysis of the sediments under in situ pressure with methods typically applied by researchers from other scientific fields (geotechnics, sedimentology, microbiology, etc.). Here we report on the design and operational procedure of the MDP and demonstrate full functionality by presenting the first results from pressure-core degassing and molecular gas analysis.

Soldier-Warfighter Operationally Responsive Deployer for Space

Science.gov (United States)

Davis, Benny; Huebner, Larry; Kuhns, Richard

2015-01-01

The Soldier-Warfighter Operationally Responsive Deployer for Space (SWORDS) project was a joint project between the U.S. Army Space & Missile Defense Command (SMDC) and NASA. The effort, lead by SMDC, was intended to develop a three-stage liquid bipropellant (liquid oxygen/liquid methane), pressure-fed launch vehicle capable of inserting a payload of at least 25 kg to a 750-km circular orbit. The vehicle design was driven by low cost instead of high performance. SWORDS leveraged commercial industry standards to utilize standard hardware and technologies over customized unique aerospace designs. SWORDS identified broadly based global industries that have achieved adequate levels of quality control and reliability in their products and then designed around their expertise and business motivations.

Regional Energy Deployment System (ReEDS)

Energy Technology Data Exchange (ETDEWEB)

Short, W.; Sullivan, P.; Mai, T.; Mowers, M.; Uriarte, C.; Blair, N.; Heimiller, D.; Martinez, A.

2011-12-01

The Regional Energy Deployment System (ReEDS) is a deterministic optimization model of the deployment of electric power generation technologies and transmission infrastructure throughout the contiguous United States into the future. The model, developed by the National Renewable Energy Laboratory's Strategic Energy Analysis Center, is designed to analyze the critical energy issues in the electric sector, especially with respect to potential energy policies, such as clean energy and renewable energy standards or carbon restrictions. ReEDS provides a detailed treatment of electricity-generating and electrical storage technologies and specifically addresses a variety of issues related to renewable energy technologies, including accessibility and cost of transmission, regional quality of renewable resources, seasonal and diurnal generation profiles, variability of wind and solar power, and the influence of variability on the reliability of the electrical grid. ReEDS addresses these issues through a highly discretized regional structure, explicit statistical treatment of the variability in wind and solar output over time, and consideration of ancillary services' requirements and costs.

The impact of antecedent trauma exposure and mental health symptoms on the post-deployment mental health of Afghanistan-deployed Australian troops.

Science.gov (United States)

Searle, Amelia K; Van Hooff, Miranda; Lawrence-Wood, Ellie R; Grace, Blair S; Saccone, Elizabeth J; Davy, Carol P; Lorimer, Michelle; McFarlane, Alexander C

2017-10-01

Both traumatic deployment experiences and antecedent traumas increase personnel's risk of developing PTSD and depression. However, only cross-sectional studies have assessed whether antecedent trauma moderates stress reactions to deployment experiences. This study prospectively examines whether antecedent trauma moderates the association between deployment trauma and post-deployment PTSD and depressive symptoms after accounting for antecedent mental health problems, in a large Australian Defence Force (ADF) sample. In the ADF Middle East Area of Operations Prospective Study, currently-serving military personnel deployed to Afghanistan across 2010-2012 (n = 1122) completed self-reported measures at pre-deployment and post-deployment. Within multivariable regressions, associations between deployment trauma and PTSD and depressive symptoms at post-deployment were stronger for personnel with greater antecedent trauma. However, once adjusting for antecedent mental health problems, these significant interaction effects disappeared. Instead, deployment-related trauma and antecedent mental health problems showed direct associations with post-deployment mental health problems. Antecedent trauma was also indirectly associated with post-deployment mental health problems through antecedent mental health problems. Similar associations were seen with prior combat exposure as a moderator. Antecedent and deployment trauma were reported retrospectively. Self-reports may also suffer from social desirability bias, especially at pre-deployment. Our main effects results support the pervasive and cumulative negative effect of trauma on military personnel, regardless of its source. While antecedent trauma does not amplify personnel's psychological response to deployment trauma, it is indirectly associated with increased post-deployment mental health problems. Antecedent mental health should be considered within pre-deployment prevention programs, and deployment-trauma within post

Cloud Storage and Bioinformatics in a private cloud deployment: Lessons for Data Intensive research

OpenAIRE

Chang, Victor; Walters, Robert John; Wills, Gary

2013-01-01

This paper describes service portability for a private cloud deployment, including a detailed case study about Cloud Storage and bioinformatics services developed as part of the Cloud Computing Adoption Framework (CCAF). Our Cloud Storage design and deployment is based on Storage Area Network (SAN) technologies, details of which include functionalities, technical implementation, architecture and user support. Experiments for data services (backup automation, data recovery and data migration) ...

5-Beam ADCP Deployment Strategy Considerations

Science.gov (United States)

Moore, T.; Savidge, D. K.; Gargett, A.

2016-02-01

With the increasing availability of 5 beam ADCPs and expanding opportunities for their deployment within both observatory and dedicated process study settings, refinements in deployment strategies are needed.Measuring vertical velocities directly with a vertically oriented acoustic beam requires that the instrument be stably mounted and leveled within fractions of a degree. Leveled shallow water deployments to date have utilized divers to jet pipes into the sand for stability, manually mount the instruments on the pipes, and level them. Leveling has been guided by the deployed instrument's pitch and roll output, available in real-time because of the observatory settings in which the deployments occurred. To expand the range of feasible deployments to deeper, perhaps non-real-time capable settings, alternatives to diver deployment and leveling must be considered. To determine stability requirements, mooring motion (heading, pitch and roll) has been sampled at 1Hz by gimballed ADCPs at a range of instrument deployment depths, and in shrouded and unshrouded cages. Conditions under which ADCP cages resting on the bottom experience significant shifts in tilt, roll or heading are assessed using co-located wind and wave measurements. The accuracy of estimating vertical velocities using all five beams relative to a well leveled vertical single beam is assessed from archived high frequency five beam data, to explore whether easing the leveling requirement is feasible.

Design and Modelling of Sustainable Bioethanol Supply Chain by Minimizing the Total Ecological Footprint in Life Cycle Perspective

DEFF Research Database (Denmark)

Ren, Jingzheng; Manzardo, Alessandro; Toniolo, Sara

2013-01-01

manners in bioethanol systems, this study developed a model for designing the most sustainable bioethanol supply chain by minimizing the total ecological footprint under some prerequisite constraints including satisfying the goal of the stakeholders', the limitation of resources and energy, the capacity......The purpose of this paper is to develop a model for designing the most sustainable bioethanol supply chain. Taking into consideration of the possibility of multiple-feedstock, multiple transportation modes, multiple alternative technologies, multiple transport patterns and multiple waste disposal...

Exploring the Deployment Potential of Small Modular Reactors

Science.gov (United States)

Abdulla, Ahmed Y.

argument for deploying SMRs in certain locations. We then decided to investigate the technical and institutional barriers hampering the development and deployment of a subset of six SMRs, including two light water designs and four non-light water advanced designs. We organized an invitational workshop that became an integrated assessment of various designs and of the institutional innovations required to bring SMRs to market. Some valuable insights were gleaned from the workshop: there is consensus that many of the challenges facing advanced SMRs are rooted in institutional biases in favor of the light water economy, as opposed to technical ones. The institutional factors that are judged to pose the greatest challenge to the mass deployment of SMRs are: the lack of a greenhouse gas control regime; political and financial instability; public concerns about nuclear safety and waste; and inadequate national and international institutions. When asked what factors most help promote SMR adoption in OECD and developing countries, economic factors dominate the list of characteristics that most contribute to their promotion in OECD countries but, when it comes to developing countries, institutional factors are regarded as being of highest import. Safety of design and safety in operation are judged the most important characteristic on both lists.

Color impact in visual attention deployment considering emotional images

Science.gov (United States)

Chamaret, C.

2012-03-01

Color is a predominant factor in the human visual attention system. Even if it cannot be sufficient to the global or complete understanding of a scene, it may impact the visual attention deployment. We propose to study the color impact as well as the emotion aspect of pictures regarding the visual attention deployment. An eye-tracking campaign has been conducted involving twenty people watching half pictures of database in full color and the other half of database in grey color. The eye fixations of color and black and white images were highly correlated leading to the question of the integration of such cues in the design of visual attention model. Indeed, the prediction of two state-of-the-art computational models shows similar results for the two color categories. Similarly, the study of saccade amplitude and fixation duration versus time viewing did not bring any significant differences between the two mentioned categories. In addition, spatial coordinates of eye fixations reveal an interesting indicator for investigating the differences of visual attention deployment over time and fixation number. The second factor related to emotion categories shows evidences of emotional inter-categories differences between color and grey eye fixations for passive and positive emotion. The particular aspect associated to this category induces a specific behavior, rather based on high frequencies, where the color components influence the visual attention deployment.

Improved design architecture to minimize functional complexity of plant protection system for nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Jung, JaeCheon, E-mail: jcjung@kings.ac.kr

2016-12-01

An improved design architecture method to minimize the functional complexity of PPS (Plant Protection System) is proposed in this work. Firstly, the design concerns are identified with both AHP (Analytic Hierarchy Process) analysis. AHP is able to identify the source of design concerns using pairwise comparison. AHP result shows CCF is the primary concern and the complexity is the secondly. Even though complexity is the second largest concern to the effectiveness of digital I&C system, but it has not been highlighted as CCF. This is the reason why this work focuses on the sources of complexity to maximize the effectiveness of digital system in the viewpoint of design architecture. The proposed methods are, separating non-safety functions from bistable logics and simplifying communication links and network. In order to verify the new concept, EFFBD (Enhanced Functional Flow Block Diagram) models are developed for two bistable logics of PPS and the complexities are measured using Halstead’s program maintainability measures. This measure specifies what provokes functional complexity. Periodic testing and operating bypass function are the source of complexity in this analysis.

Improved design architecture to minimize functional complexity of plant protection system for nuclear power plant

International Nuclear Information System (INIS)

Jung, JaeCheon

2016-01-01

An improved design architecture method to minimize the functional complexity of PPS (Plant Protection System) is proposed in this work. Firstly, the design concerns are identified with both AHP (Analytic Hierarchy Process) analysis. AHP is able to identify the source of design concerns using pairwise comparison. AHP result shows CCF is the primary concern and the complexity is the secondly. Even though complexity is the second largest concern to the effectiveness of digital I&C system, but it has not been highlighted as CCF. This is the reason why this work focuses on the sources of complexity to maximize the effectiveness of digital system in the viewpoint of design architecture. The proposed methods are, separating non-safety functions from bistable logics and simplifying communication links and network. In order to verify the new concept, EFFBD (Enhanced Functional Flow Block Diagram) models are developed for two bistable logics of PPS and the complexities are measured using Halstead’s program maintainability measures. This measure specifies what provokes functional complexity. Periodic testing and operating bypass function are the source of complexity in this analysis.

Supporting Collaborative Model and Data Service Development and Deployment with DevOps

Science.gov (United States)

David, O.

2016-12-01

Adopting DevOps practices for model service development and deployment enables a community to engage in service-oriented modeling and data management. The Cloud Services Integration Platform (CSIP) developed the last 5 years at Colorado State University provides for collaborative integration of environmental models into scalable model and data services as a micro-services platform with API and deployment infrastructure. Originally developed to support USDA natural resource applications, it proved suitable for a wider range of applications in the environmental modeling domain. While extending its scope and visibility it became apparent community integration and adequate work flow support through the full model development and application cycle drove successful outcomes.DevOps provide best practices, tools, and organizational structures to optimize the transition from model service development to deployment by minimizing the (i) operational burden and (ii) turnaround time for modelers. We have developed and implemented a methodology to fully automate a suite of applications for application lifecycle management, version control, continuous integration, container management, and container scaling to enable model and data service developers in various institutions to collaboratively build, run, deploy, test, and scale services within minutes.To date more than 160 model and data services are available for applications in hydrology (PRMS, Hydrotools, CFA, ESP), water and wind erosion prediction (WEPP, WEPS, RUSLE2), soil quality trends (SCI, STIR), water quality analysis (SWAT-CP, WQM, CFA, AgES-W), stream degradation assessment (SWAT-DEG), hydraulics (cross-section), and grazing management (GRAS). In addition, supporting data services include soil (SSURGO), ecological site (ESIS), climate (CLIGEN, WINDGEN), land management and crop rotations (LMOD), and pesticides (WQM), developed using this workflow automation and decentralized governance.

A Depth-Adjustment Deployment Algorithm Based on Two-Dimensional Convex Hull and Spanning Tree for Underwater Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Peng Jiang

2016-07-01

Full Text Available Most of the existing node depth-adjustment deployment algorithms for underwater wireless sensor networks (UWSNs just consider how to optimize network coverage and connectivity rate. However, these literatures don’t discuss full network connectivity, while optimization of network energy efficiency and network reliability are vital topics for UWSN deployment. Therefore, in this study, a depth-adjustment deployment algorithm based on two-dimensional (2D convex hull and spanning tree (NDACS for UWSNs is proposed. First, the proposed algorithm uses the geometric characteristics of a 2D convex hull and empty circle to find the optimal location of a sleep node and activate it, minimizes the network coverage overlaps of the 2D plane, and then increases the coverage rate until the first layer coverage threshold is reached. Second, the sink node acts as a root node of all active nodes on the 2D convex hull and then forms a small spanning tree gradually. Finally, the depth-adjustment strategy based on time marker is used to achieve the three-dimensional overall network deployment. Compared with existing depth-adjustment deployment algorithms, the simulation results show that the NDACS algorithm can maintain full network connectivity with high network coverage rate, as well as improved network average node degree, thus increasing network reliability.

How and when 4. generation nuclear systems could deploy?

International Nuclear Information System (INIS)

Safa, H.; Bonin, B.

2007-01-01

Fast reactors exhibit two major advantages over classical thermal reactors: sustainability and waste minimization. The deployment of 4. generation nuclear reactors depends on economical, industrial and political issues. We feel that the waste radiotoxicity reduction argument, although very crucial and socially sensitive, could not by itself justify implementing a new reactor system including a dedicated reprocessing scheme. But the foreseen tension of the uranium market may urge on developing fast reactor systems. Putting aside politics, we tentatively try to answer a very simple question: At which uranium price will it be economically competitive to build a fast reactor instead of a light water one? The leveled cost of nuclear electricity is analyzed and split into its different components (investment, fuel supply, fuel cycle,..). Assuming some minimal and reasonable hypotheses, fast reactors costs are compared with light water ones. The uranium price necessary to compensate for the higher investment cost of fast reactors is then deduced. One major conclusion that can be drawn from our study may be summarized as follows: if the uranium market price maintains its present level for a long period of time, fast reactors are already today an economically attractive option. (authors)

How and when 4. generation nuclear systems could deploy?

Energy Technology Data Exchange (ETDEWEB)

Safa, H.; Bonin, B. [CEA Saclay, Dir. de l' Energie Nucleaire, 91 - Gif sur Yvette (France)

2007-07-01

Fast reactors exhibit two major advantages over classical thermal reactors: sustainability and waste minimization. The deployment of 4. generation nuclear reactors depends on economical, industrial and political issues. We feel that the waste radiotoxicity reduction argument, although very crucial and socially sensitive, could not by itself justify implementing a new reactor system including a dedicated reprocessing scheme. But the foreseen tension of the uranium market may urge on developing fast reactor systems. Putting aside politics, we tentatively try to answer a very simple question: At which uranium price will it be economically competitive to build a fast reactor instead of a light water one? The leveled cost of nuclear electricity is analyzed and split into its different components (investment, fuel supply, fuel cycle,..). Assuming some minimal and reasonable hypotheses, fast reactors costs are compared with light water ones. The uranium price necessary to compensate for the higher investment cost of fast reactors is then deduced. One major conclusion that can be drawn from our study may be summarized as follows: if the uranium market price maintains its present level for a long period of time, fast reactors are already today an economically attractive option. (authors)

NEON's Mobile Deployment Platform: A Resource for Community Research

Science.gov (United States)

Sanclements, M.

2015-12-01

Here we provide an update on construction and validation of the NEON Mobile Deployment Platforms (MDPs) as well as a description of the infrastructure and sensors available to researchers in the future. The MDPs will provide the means to observe stochastic or spatially important events, gradients, or quantities that cannot be reliably observed using fixed location sampling (e.g. fires and floods). Due to the transient temporal and spatial nature of such events, the MDPs will be designed to accommodate rapid deployment for time periods up to ~ 1 year. Broadly, the MDPs will be comprised of infrastructure and instrumentation capable of functioning individually or in conjunction with one another to support observations of ecological change, as well as education, training and outreach.

Modeling EERE Deployment Programs

Energy Technology Data Exchange (ETDEWEB)

Cort, K. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hostick, D. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Belzer, D. B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Livingston, O. V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2007-11-01

This report compiles information and conclusions gathered as part of the “Modeling EERE Deployment Programs” project. The purpose of the project was to identify and characterize the modeling of deployment programs within the EERE Technology Development (TD) programs, address possible improvements to the modeling process, and note gaps in knowledge in which future research is needed.

Specialized minimal PDFs for optimized LHC calculations

NARCIS (Netherlands)

Carrazza, Stefano; Forte, Stefano; Kassabov, Zahari; Rojo, Juan

2016-01-01

We present a methodology for the construction of parton distribution functions (PDFs) designed to provide an accurate representation of PDF uncertainties for specific processes or classes of processes with a minimal number of PDF error sets: specialized minimal PDF sets, or SM-PDFs. We construct

Development of the solar array deployment and drive system for the XTE spacecraft

Science.gov (United States)

Farley, Rodger; Ngo, Son

1995-01-01

The X-ray Timing Explorer (XTE) spacecraft is a NASA science low-earth orbit explorer-class satellite to be launched in 1995, and is an in-house Goddard Space Flight Center (GSFC) project. It has two deployable aluminum honeycomb solar array wings with each wing being articulated by a single axis solar array drive assembly. This paper will address the design, the qualification testing, and the development problems as they surfaced of the Solar Array Deployment and Drive System.

Advances in the design, development, and deployment of the U.S. Army Research Laboratory (ARL) multimodal signatures database

Science.gov (United States)

Bennett, Kelly; Robertson, James

2011-06-01

Recent advances in the design, development, and deployment of U.S. Army Research Laboratory's (ARL) Multimodal Signature Database (MMSDB) create a state-of-the-art database system with Web-based access through a Web interface designed specifically for research and development. Tens of thousands of signatures are currently available for researchers to support their algorithm development and refinement for sensors and other security systems. Each dataset is stored in (Hierarchical Data Format 5 (HDF5) format for easy modeling and storing of signatures and archived sensor data, ground truth, calibration information, algorithms, and other documentation. Archived HDF5 formatted data provides the basis for computational interoperability across a variety of tools including MATLAB, Octave, and Python. The database has a Web-based front-end with public and restricted access interfaces, along with 24/7 availability and support. This paper describes the overall design of the system, and the recent enhancements and future vision, including the ability for researchers to share algorithms, data, and documentation in the cloud, and providing an ability to run algorithms and software for testing and evaluation purposes remotely across multiple domains and computational tools. The paper will also describe in detail the HDF5 format for several multimodal sensor types.

Biomechanics of an Expandable Lumbar Interbody Fusion Cage Deployed Through Transforaminal Approach

Science.gov (United States)

Mica, Michael Conti; Voronov, Leonard I.; Carandang, Gerard; Havey, Robert M.; Wojewnik, Bartosz

2017-01-01

Introduction A novel expandable lumbar interbody fusion cage has been developed which allows for a broad endplate footprint similar to an anterior lumbar interbody fusion (ALIF); however, it is deployed from a minimally invasive transforaminal unilateral approach. The perceived benefit is a stable circumferential fusion from a single approach that maintains the anterior tension band of the anterior longitudinal ligament. The purpose of this biomechanics laboratory study was to evaluate the biomechanical stability of an expandable lumbar interbody cage inserted using a transforaminal approach and deployed in situ compared to a traditional lumbar interbody cage inserted using an anterior approach (control device). Methods Twelve cadaveric spine specimens (L1-L5) were tested intact and after implantation of both the control and experimental devices in two (L2-L3 and L3-L4) segments of each specimen; the assignments of the control and experimental devices to these segments were alternated. Effect of supplemental pedicle screw-rod stabilization was also assessed. Moments were applied to the specimens in flexion-extension (FE), lateral bending (LB), and axial rotation (AR). The effect of physiologic preload on construct stability was evaluated in FE. Segmental motions were measured using an optoelectronic motion measurement system. Results The deployable expendable TLIF cage and control devices significantly reduced FE motion with and without compressive preload when compared to the intact condition (p0.05). Adding bilateral pedicle screws resulted in further reduction of ROM for all loading modes compared to intact condition, with no statistical difference between the two constructs (p>0.05). Conclusions The ability of the deployable expendable interbody cage in reducing segmental motions was equivalent to the control cage when used as a stand-alone construct and also when supplemented with bilateral pedicle screw-rod instrumentation. The larger footprint of the fully

Adaptable Deployable Entry & Placement Technology (ADEPT) for Cubesat Delivery to Mars Surface

Science.gov (United States)

Wercinski, Paul

2014-01-01

The Adaptable, Deployable Entry and Placement Technology (ADEPT), uses a mechanical skeleton to deploy a revolutionary carbon fabric system that serves as both heat shield and primary structure during atmospheric entry. The NASA ADEPT project, currently funded by the Game Changing Development Program in STMD is currently focused on 1m class hypersonic decelerators for the delivery of very small payloads ( 5 kg) to locations of interest in an effort to leverage low-cost platforms to rapidly mature the technology while simultaneously delivering high-value science. Preliminary mission design and aerothermal performance testing in arcjets have shown the ADEPT system is quite capable of safe delivery of cubesats to Mars surface. The ability of the ADEPT to transit to Mars in a stowed configuration (similar to an umbrella) provides options for integration with the Mars 2020 cruise stage, even to consider multiple ADEPTs. System-level test campaigns are underway for FY15 execution or planning for FY16. These include deployment testing, wind tunnel testing, system-level arc jet testing, and a sounding rocket flight test. The goal is system level maturation (TRL 6) at a 1m class Mars design reference mission configuration.

WING/WORLD: An Open Experimental Toolkit for the Design and Deployment of IEEE 802.11-Based Wireless Mesh Networks Testbeds

Directory of Open Access Journals (Sweden)

Daniele Miorandi

2010-01-01

Full Text Available Wireless Mesh Networks represent an interesting instance of light-infrastructure wireless networks. Due to their flexibility and resiliency to network failures, wireless mesh networks are particularly suitable for incremental and rapid deployments of wireless access networks in both metropolitan and rural areas. This paper illustrates the design and development of an open toolkit aimed at supporting the design of different solutions for wireless mesh networking by enabling real evaluation, validation, and demonstration. The resulting testbed is based on off-the-shelf hardware components and open-source software and is focused on IEEE 802.11 commodity devices. The software toolkit is based on an “open” philosophy and aims at providing the scientific community with a tool for effective and reproducible performance analysis of WMNs. The paper describes the architecture of the toolkit, and its core functionalities, as well as its potential evolutions.

VisPortal: Deploying grid-enabled visualization tools through a web-portal interface

Energy Technology Data Exchange (ETDEWEB)

Bethel, Wes; Siegerist, Cristina; Shalf, John; Shetty, Praveenkumar; Jankun-Kelly, T.J.; Kreylos, Oliver; Ma, Kwan-Liu

2003-06-09

The LBNL/NERSC Visportal effort explores ways to deliver advanced Remote/Distributed Visualization (RDV) capabilities through a Grid-enabled web-portal interface. The effort focuses on latency tolerant distributed visualization algorithms, GUI designs that are more appropriate for the capabilities of web interfaces, and refactoring parallel-distributed applications to work in a N-tiered component deployment strategy. Most importantly, our aim is to leverage commercially-supported technology as much as possible in order to create a deployable, supportable, and hence viable platform for delivering grid-based visualization services to collaboratory users.

Non-traditional Infrasound Deployment

Science.gov (United States)

McKenna, M. H.; McComas, S.; Simpson, C. P.; Diaz-Alvarez, H.; Costley, R. D.; Hayward, C.; Golden, P.; Endress, A.

2017-12-01

Historically, infrasound arrays have been deployed in rural environments where anthropological noise sources are limited. As interest in monitoring low energy sources at local distances grows in the infrasound community, it will be vital to understand how to monitor infrasound sources in an urban environment. Arrays deployed in urban centers have to overcome the decreased signal-to-noise ratio and reduced amount of real estate available to deploy an array. To advance the understanding of monitoring infrasound sources in urban environments, local and regional infrasound arrays were deployed on building rooftops on the campus at Southern Methodist University (SMU), and data were collected for one seasonal cycle. The data were evaluated for structural source signals (continuous-wave packets), and when a signal was identified, the back azimuth to the source was determined through frequency-wavenumber analysis. This information was used to identify hypothesized structural sources; these sources were verified through direct measurement and dynamic structural analysis modeling. In addition to the rooftop arrays, a camouflaged infrasound sensor was installed on the SMU campus and evaluated to determine its effectiveness for wind noise reduction. Permission to publish was granted by Director, Geotechnical and Structures Laboratory.

Louisville region demonstration of travel management coordination center : system pre-deployment preparation.

Science.gov (United States)

2013-03-01

The purpose of the Greater Louisville Region Demonstration of Travel Management Coordination Center (TMCC): System Pre-Deploy-ment Preparation grant was to further phased implementation of the regions TMCC design by focusing on two major component...

Deployable Brake for Spacecraft

Science.gov (United States)

Rausch, J. R.; Maloney, J. W.

1987-01-01

Aerodynamic shield that could be opened and closed proposed. Report presents concepts for deployable aerodynamic brake. Brake used by spacecraft returning from high orbit to low orbit around Earth. Spacecraft makes grazing passes through atmosphere to slow down by drag of brake. Brake flexible shield made of woven metal or ceramic withstanding high temperatures created by air friction. Stored until needed, then deployed by set of struts.

Analysis of Wireless Sensor Network Topology and Estimation of Optimal Network Deployment by Deterministic Radio Channel Characterization

Directory of Open Access Journals (Sweden)

Erik Aguirre

2015-02-01

Full Text Available One of the main challenges in the implementation and design of context-aware scenarios is the adequate deployment strategy for Wireless Sensor Networks (WSNs, mainly due to the strong dependence of the radiofrequency physical layer with the surrounding media, which can lead to non-optimal network designs. In this work, radioplanning analysis for WSN deployment is proposed by employing a deterministic 3D ray launching technique in order to provide insight into complex wireless channel behavior in context-aware indoor scenarios. The proposed radioplanning procedure is validated with a testbed implemented with a Mobile Ad Hoc Network WSN following a chain configuration, enabling the analysis and assessment of a rich variety of parameters, such as received signal level, signal quality and estimation of power consumption. The adoption of deterministic radio channel techniques allows the design and further deployment of WSNs in heterogeneous wireless scenarios with optimized behavior in terms of coverage, capacity, quality of service and energy consumption.

Analysis of wireless sensor network topology and estimation of optimal network deployment by deterministic radio channel characterization.

Science.gov (United States)

Aguirre, Erik; Lopez-Iturri, Peio; Azpilicueta, Leire; Astrain, José Javier; Villadangos, Jesús; Falcone, Francisco

2015-02-05

One of the main challenges in the implementation and design of context-aware scenarios is the adequate deployment strategy for Wireless Sensor Networks (WSNs), mainly due to the strong dependence of the radiofrequency physical layer with the surrounding media, which can lead to non-optimal network designs. In this work, radioplanning analysis for WSN deployment is proposed by employing a deterministic 3D ray launching technique in order to provide insight into complex wireless channel behavior in context-aware indoor scenarios. The proposed radioplanning procedure is validated with a testbed implemented with a Mobile Ad Hoc Network WSN following a chain configuration, enabling the analysis and assessment of a rich variety of parameters, such as received signal level, signal quality and estimation of power consumption. The adoption of deterministic radio channel techniques allows the design and further deployment of WSNs in heterogeneous wireless scenarios with optimized behavior in terms of coverage, capacity, quality of service and energy consumption.

Automated scheme to determine design parameters for a recoverable reentry vehicle

International Nuclear Information System (INIS)

Williamson, W.E.

1976-01-01

The NRV (Nosetip Recovery Vehicle) program at Sandia Laboratories is designed to recover the nose section from a sphere cone reentry vehicle after it has flown a near ICBM reentry trajectory. Both mass jettison and parachutes are used to reduce the velocity of the RV near the end of the trajectory to a sufficiently low level that the vehicle may land intact. The design problem of determining mass jettison time and parachute deployment time in order to ensure that the vehicle does land intact is considered. The problem is formulated as a min-max optimization problem where the design parameters are to be selected to minimize the maximum possible deviation in the design criteria due to uncertainties in the system. The results of the study indicate that the optimal choice of the design parameters ensures that the maximum deviation in the design criteria is within acceptable bounds. This analytically ensures the feasibility of recovery for NRV

Microsoft Exchange Server 2013 design, deploy and deliver an enterprise messaging solution

CERN Document Server

Winters, Nathan; Blank, Nicolas

2013-01-01

Successfully deploy a top-quality Exchange messaging service Rolling out a major messaging service with Microsoft Exchange Server 2013 requires that you not only understand the functionality of this exciting new release, but that you fully grasp all aspects of the larger Exchange server ecosystem as well. This practical book is your best field guide to it all. Written for administrators and consultants in the trenches, this innovative new guide begins with key concepts of Microsoft Exchange Server 2013 and then moves through the recommended practices and processes that are neces

Outcomes of AV Fistulas and AV Grafts after Interventional Stent-Graft Deployment in Haemodialysis Patients

Energy Technology Data Exchange (ETDEWEB)

Schmelter, Christopher, E-mail: christopher.schmelter@klinikum-ingolstadt.de; Raab, Udo, E-mail: udo.raab@klinikum-ingolstadt.de [Klinikum Ingolstadt, Department of Diagnostic and Interventional Radiology (Germany); Lazarus, Friedrich, E-mail: friedrich.lazarus@klinikum-ingolstadt.de [Klinikum Ingolstadt, Department of Nephrology (Germany); Ruppert, Volker, E-mail: volker.ruppert@klinikum-ingolstadt.de [Klinikum Ingolstadt, Department of Vascular Surgery (Germany); Vorwerk, Dierk, E-mail: dierk.vorwerk@klinikum-ingolstadt.de [Klinikum Ingolstadt, Department of Diagnostic and Interventional Radiology (Germany)

2015-08-15

PurposeThe study was designed to assess outcomes of arteriovenous (AV) accesses after interventional stent-graft deployment in haemodialysis patients.Materials and Methods63 haemodialysis patients with 66 AV fistulas and AV grafts were treated by interventional stent-graft deployment from 2006 to 2012 at our hospital. Data of these patients were retrospectively analysed for location of deployed stent-grafts, occurrence and location of (re-)stenosis and (re-)thrombosis. Complex stenosis was the most frequent indication for stent-graft deployment (45.5 %), followed by complications of angioplasty with vessel rupture or dissection (31.8 %).ResultsA high rate of procedural success was achieved (98.5 %). The most frequent location of the deployed stent-graft was the draining vein (66.7 %). Stent-graft deployment was more frequent in AV grafts than in AV fistulas. Primary patency was 45.5 % at 6 month, 31.3 % at 12 month and 19.2 % at 24 month. Primary patency was significantly better for AV fistulas than for AV grafts with deployed stent-grafts. Patency of the deployed stent-graft was much better than overall AV access primary patency with deployed stent-graft. Re-stenosis with thrombosis was the most frequent indication for re-intervention. Most frequent location of re-stenosis was the draining vein (37.1 %), followed by stenosis at the AV access (29.5 %) and the deployed stent-graft (23.5 %).ConclusionRe-stenosis and re-thrombosis remain frequent in AV fistulas and AV grafts in haemodialysis patients despite stent-graft deployment. Re-stenosis of the deployed stent-graft is, only in the minority of the cases, responsible for AV access dysfunction.

Sensitivity computation of the l1 minimization problem and its application to dictionary design of ill-posed problems

International Nuclear Information System (INIS)

Horesh, L; Haber, E

2009-01-01

The l 1 minimization problem has been studied extensively in the past few years. Recently, there has been a growing interest in its application for inverse problems. Most studies have concentrated in devising ways for sparse representation of a solution using a given prototype dictionary. Very few studies have addressed the more challenging problem of optimal dictionary construction, and even these were primarily devoted to the simplistic sparse coding application. In this paper, sensitivity analysis of the inverse solution with respect to the dictionary is presented. This analysis reveals some of the salient features and intrinsic difficulties which are associated with the dictionary design problem. Equipped with these insights, we propose an optimization strategy that alleviates these hurdles while utilizing the derived sensitivity relations for the design of a locally optimal dictionary. Our optimality criterion is based on local minimization of the Bayesian risk, given a set of training models. We present a mathematical formulation and an algorithmic framework to achieve this goal. The proposed framework offers the design of dictionaries for inverse problems that incorporate non-trivial, non-injective observation operators, where the data and the recovered parameters may reside in different spaces. We test our algorithm and show that it yields improved dictionaries for a diverse set of inverse problems in geophysics and medical imaging

Sensitivity computation of the ell1 minimization problem and its application to dictionary design of ill-posed problems

Science.gov (United States)

Horesh, L.; Haber, E.

2009-09-01

The ell1 minimization problem has been studied extensively in the past few years. Recently, there has been a growing interest in its application for inverse problems. Most studies have concentrated in devising ways for sparse representation of a solution using a given prototype dictionary. Very few studies have addressed the more challenging problem of optimal dictionary construction, and even these were primarily devoted to the simplistic sparse coding application. In this paper, sensitivity analysis of the inverse solution with respect to the dictionary is presented. This analysis reveals some of the salient features and intrinsic difficulties which are associated with the dictionary design problem. Equipped with these insights, we propose an optimization strategy that alleviates these hurdles while utilizing the derived sensitivity relations for the design of a locally optimal dictionary. Our optimality criterion is based on local minimization of the Bayesian risk, given a set of training models. We present a mathematical formulation and an algorithmic framework to achieve this goal. The proposed framework offers the design of dictionaries for inverse problems that incorporate non-trivial, non-injective observation operators, where the data and the recovered parameters may reside in different spaces. We test our algorithm and show that it yields improved dictionaries for a diverse set of inverse problems in geophysics and medical imaging.

Supporting Knowledge Transfer in IS Deployment Projects

Science.gov (United States)

Schönström, Mikael

To deploy new information systems is an expensive and complex task, and does seldom result in successful usage where the system adds strategic value to the firm (e.g. Sharma et al. 2003). It has been argued that innovation diffusion is a knowledge integration problem (Newell et al. 2000). Knowledge about business processes, deployment processes, information systems and technology are needed in a large-scale deployment of a corporate IS. These deployments can therefore to a large extent be argued to be a knowledge management (KM) problem. An effective deployment requires that knowledge about the system is effectively transferred to the target organization (Ko et al. 2005).

Ranking factors involved in product design using a hybrid model of Quality Function Deployment, Data Envelopment Analysis and TOPSIS technique

Directory of Open Access Journals (Sweden)

Davood Feiz

2014-08-01

Full Text Available Quality function deployment (QFD is one such extremely important quality management tool, which is useful in product design and development. Traditionally, QFD rates the design requirements (DRs with respect to customer requirements, and aggregates the rating to get relative importance score of DRs. An increasing number of studies emphasize on the need to incorporate additional factors, such as cost and environmental impact, while calculating the relative importance of DRs. However, there are different methodologies for driving the relative importance of DRs, when several additional factors are considered. TOPSIS (technique for order preferences by similarity to ideal solution is suggested for the purpose of the research. This research proposes new approach of TOPSIS for considering the rating of DRs with respect to CRs, and several additional factors, simultaneously. Proposed method is illustrated using by step-by-step procedure. The proposed methodology was applied for the Sanam Electronic Company in Iran.

PERANCANGAN CASING DAN TATA LETAK KOMPONEN OZONIZER PENGAWET MAKANAN MENGGUNAKAN METODE QUALITY FUNCTION DEPLOYMENT (QFD

Directory of Open Access Journals (Sweden)

Zainal Fanani

2012-02-01

Full Text Available Penelitian ini berisi tentang perancangan casing dan tata letak komponen ozonizer pengawet makanan. Proses perancangan produk dilakukan dengan menggunakan metode Quality Function Deployment (QFD pada fase perencanaan produk (Product Planning dan fase perencanaan disain (Design Planning. Pada fase perencanaan produk, dilakukan identifikasi kebutuhan konsumen terhadap ozonizer pengawet makanan. Pengumpulan data mengenai kebutuhan konsumen diperoleh dari penyebaran angket (kuisioner kepada pengguna produk, yaitu rumah makan dan industri makanan. Setelah diperoleh daftar kebutuhan konsumen, kebutuhan-kebutuhan tersebut kemudian diolah menggunakan metode QFD pada fase perencanaan produk hingga diperoleh spestifikasi teknis produk dan House of Quality (HOQ. Spesifikasi teknis produk ini akan digunakan sebagai acuan dalam menyusun fase kedua proses QFD, yaitu fase perencanaan disain. Pada fase perencanaan disain, dihasilkan beberapa sketsa alternatif solusi. Alternatif solusi disain tersebut kemudian dievaluasi dan dilakukan penilaian untuk memilih solusi disain produk ozonizer pengawet makanan. Setelah solusi disain produk ozonizer dipilih, alternatif solusi tersebut kemudian dirancang secara detail, dan kemudian dibuat prototype produk. Prototype produk  yang dibuat adalah prototype visual, yakni gambar disain yang dianimasi untuk melihat proses perakitan, penyusunan tata letak komponen penyusun produk dan penyusunan display dan panel operasi produk. Kata Kunci   :   Kebutuhan konsumen, Quality Function Deployment, Spesifikasi Teknis Produk, Solusi Disain, Prototype Disain Produk     This research contains about casing project and ozonizer component layout of food preservative. The project is practiced using Quality Function Deployment (QFD method on product planning and design planning phase. In product planning phase, there is identification about consumer needs in ozonizer food preservative. Collecting data about consumer needs are received

A new deployable structure for the nomad art

OpenAIRE

ZHANG, Y; ZHANG, Q

2005-01-01

This paper presents a project of the international archtecture and structure competition preparing the annual conference of the IASS 2004 at Montpellier in France. A new kind of depolyable structure is designed to fit the requirements of the nomad art. With a poetical implication and a good assemblage and dismantling, this deployable structure needs an ordered construction procedure. During structure analysis, two phases have been distinguished : the construction phase and the working phase. ...

Staged deployment of the International Fusion Materials Irradiation Facility

International Nuclear Information System (INIS)

Takeuchi, H.; Sugimoto, M.; Nakamura, H.

2001-01-01

The International Fusion Materials Irradiation Facility (IFMIF) employs an accelerator based D-Li intense neutron source as defined in the 1995-96 Conceptual Design Activity (CDA) study. In 1999, IEA mandated a review of the CDA IFMIF design for cost reduction without change to its original mission. This objective was accomplished by eliminating the previously assumed possibility of potential upgrade of IFMIF beyond the user requirements. The total estimated cost was reduced from $797.2 M to $487.8 M. An option of deployment in 3 stages was also examined to reduce the initial investment and annual expenditures during construction. In this scenario, full performance is achieved gradually with each interim stage as follows. 1st Stage: 20% operation for material selection for ITER breeding blanket, 2nd Stage: 50% operation to demonstrate materials performance of a reference alloy for DEMO, 3rd Stage: full performance operation ( 2MW/m 2 at 500cm 3 ) to obtain engineering data for potential DEMO materials under irradiation up to 100-200 dpa. In summary, the new, reduced cost IFMIF design and staged deployment still satisfies the original mission. The estimated cost of the 1st Stage facility is only $303.6 M making it financially much more attractive. Currently, IFMIF Key Element Technology Phase (KEP) is underway to reduce the key technology risk factors. (author)

On the hop count statistics for randomly deployed wireless sensor networks

NARCIS (Netherlands)

Dulman, S.O.; Rossi, M.; Havinga, Paul J.M.; Zorzi, M.

2006-01-01

In this paper we focus on exploiting the information provided by a generally accepted and largely ignored hypothesis (the random deployment of the nodes of an ad hoc or wireless sensor network) to design improved networking protocols. Specifically, we derive the relationship between the number of

DESAIN DAN PEMBUATAN ALAT PENGGILING DAGING DENGAN QUALITY FUNCTION DEPLOYMENT

Directory of Open Access Journals (Sweden)

Stefanus Ongkodjojo

2006-01-01

Full Text Available Quality Function Deployment (QFD is a powerful development methodology with a wide range of applications. This paper presents a simple case using QFD on the design, detail, and process phase of a Meat Grinder product as a tool of improvement for hygienic of the Meat Grinder. The main purpose of QFD in this study was to apply in construction a method of customer-oriented design used in other industries, and to adapt some of the tables and matrices. Another purpose of this case study was to test the applicability of QFD in the design and process planning of a Meat Grinder. The developed prototype was chosen to be the screw part as the main part of the Grinder and a significant achievement was made on the improvement of hygienic, noted on less corrosive material selected of aluminum alloy 514.0 and improvement of surface roughness of 62.2%. Abstract in Bahasa Indonesia : Quality Function Deployment (QFD adalah metodologi pengembangan yang cukup handal dengan rentang aplikasi yang luas. Makalah ini mempresentasikan kasus sederhana penggunaan metode QFD pada tahapan desain, detail dan proses produk penggiling daging sebagai alat untuk meningkatkan higenitasnya. Tujuan utama dari QFD pada studi ini adalah untuk menerapkan desain yang berorientasi pada pelanggan dengan mengadaptasi beberapa matriks dan table pada tahapan-tahapannya. Tujuan yang lain yaitu untuk menguji kemampuan QFD pada proses perancangan sebuah penggiling daging. Prototipe yang dipilih untuk dikembangkan yaitu bagian ulir sebagai bagian utama dari sebuah penggiling daging dan hasil yang cukup signifikan telah didapat pada hal higenitas, ditandai dengan terpilihnya material yang kurang korosif yaitu paduan aluminium 514.0 sebagai material yang digunakan serta perbaikan nilai kekasaran permukaan sebesar 62.2 % dari produk yang telah ada dipasaran. Kata kunci: quality function deployment, the house of quality, penggiling daging.

Efficient Deployment of Key Nodes for Optimal Coverage of Industrial Mobile Wireless Networks.

Science.gov (United States)

Li, Xiaomin; Li, Di; Dong, Zhijie; Hu, Yage; Liu, Chengliang

2018-02-10

In recent years, industrial wireless networks (IWNs) have been transformed by the introduction of mobile nodes, and they now offer increased extensibility, mobility, and flexibility. Nevertheless, mobile nodes pose efficiency and reliability challenges. Efficient node deployment and management of channel interference directly affect network system performance, particularly for key node placement in clustered wireless networks. This study analyzes this system model, considering both industrial properties of wireless networks and their mobility. Then, static and mobile node coverage problems are unified and simplified to target coverage problems. We propose a novel strategy for the deployment of clustered heads in grouped industrial mobile wireless networks (IMWNs) based on the improved maximal clique model and the iterative computation of new candidate cluster head positions. The maximal cliques are obtained via a double-layer Tabu search. Each cluster head updates its new position via an improved virtual force while moving with full coverage to find the minimal inter-cluster interference. Finally, we develop a simulation environment. The simulation results, based on a performance comparison, show the efficacy of the proposed strategies and their superiority over current approaches.

Design Mixers to Minimize Effects of Erosion and Corrosion Erosion

Directory of Open Access Journals (Sweden)

Julian Fasano

2012-01-01

Full Text Available A thorough review of the major parameters that affect solid-liquid slurry wear on impellers and techniques for minimizing wear is presented. These major parameters include (i chemical environment, (ii hardness of solids, (iii density of solids, (iv percent solids, (v shape of solids, (vi fluid regime (turbulent, transitional, or laminar, (vii hardness of the mixer's wetted parts, (viii hydraulic efficiency of the impeller (kinetic energy dissipation rates near the impeller blades, (ix impact velocity, and (x impact frequency. Techniques for minimizing the wear on impellers cover the choice of impeller, size and speed of the impeller, alloy selection, and surface coating or coverings. An example is provided as well as an assessment of the approximate life improvement.

Building-in-Briefcase: A Rapidly-Deployable Environmental Sensor Suite for the Smart Building.

Science.gov (United States)

Weekly, Kevin; Jin, Ming; Zou, Han; Hsu, Christopher; Soyza, Chris; Bayen, Alexandre; Spanos, Costas

2018-04-29

A building’s environment has profound influence on occupant comfort and health. Continuous monitoring of building occupancy and environment is essential to fault detection, intelligent control, and building commissioning. Though many solutions for environmental measuring based on wireless sensor networks exist, they are not easily accessible to households and building owners who may lack time or technical expertise needed to set up a system and get quick and detailed overview of environmental conditions. Building-in-Briefcase (BiB) is a portable sensor network platform that is trivially easy to deploy in any building environment. Once the sensors are distributed, the environmental data is collected and communicated to the BiB router via the Transmission Control Protocol/Internet Protocol (TCP/IP) and WiFi technology, which then forwards the data to the central database securely over the internet through a 3G radio. The user, with minimal effort, can access the aggregated data and visualize the trends in real time on the BiB web portal. Paramount to the adoption and continued operation of an indoor sensing platform is battery lifetime. This design has achieved a multi-year lifespan by careful selection of components, an efficient binary communications protocol and data compression. Our BiB sensor is capable of collecting a rich set of environmental parameters, and is expandable to measure others, such as CO 2 . This paper describes the power characteristics of BiB sensors and their occupancy estimation and activity recognition functionality. We have demonstrated large-scale deployment of BiB throughout Singapore. Our vision is that, by monitoring thousands of buildings through BiB, it would provide ample research opportunities and opportunities to identify ways to improve the building environment and energy efficiency.

The effect of military deployment on mental health

DEFF Research Database (Denmark)

Lyk-Jensen, Stéphanie; Weatherall, Cecilie Dohlmann; W. Jepsen, Peter

for the non-deployed eligible men, and our results hold to various robustness checks. Our administrative records provide objective measures of mental health service use in the form of psychiatric diagnoses and purchase of mental health-related medication. The very rich data makes it possible to control......In this paper we estimate the causal effect of military deployment on soldiers’ mental health. To handle the selection bias problem, we use longitudinal data for deployed and non-deployed eligible men in a difference-in-differences setting. Using pair-wise matching, we impute deployment dates...... for important variables like intelligence tests and family background. We find significant adverse effects of military deployment on soldiers’ mental health service use. Highlights: - Causal effect of military deployment on soldiers’ use of mental health service - Using a difference-in-differences approach...

CCT deployment considerations

International Nuclear Information System (INIS)

Yamagata, B.

1993-01-01

The deployment of Clean Coal Technologies (CCT) is discussed by asserting that in the case of commercializing CCT, the government's involvement should not stop at the demonstration gate. Two areas in this regard are described. First, the need for the domestic DOE CCT Program to focus on the domestic deployment of demonstrated technologies, and second, the need to recognize that to participate in the phenomenal growth of international power markets through use of clean coal or advanced coal technologies an aggressive partnering between the government and industry to demonstrate technologies abroad will be required. The Clean Coal Technology Coalition's (CCT) primary mission has been to promote the development and use of CCTs. The CCT is a strong advocate for the DOE CCT Program and applauds the Department's and industry's success at developing many coal-based technologies. By current design, the DOE program is said to go no further than the initial demonstration of a technology. Since the inception of CCT in 1986, the Coalition has advocated the need to pursue a partnership with government in which more than one demonstration of the same or similar technology is supported by the clean coal program. Only in this way can one be assured of widespread acceptance of any given technology. There exists a gap (call it a open-quotes risk gapclose quotes) between CCTs that have been successfully demonstrated (and presumably available for commercial use) and their widespread commercial use. A technology matrix has been developed in which the developmental status of a variety of clean coal technologies is demonstrated. While still too early to pass judgment, it appears that while success is being achieved in demonstrating advanced coal technologies, the market place - for several reasons - is not, indeed may have no plans, to adopt these technologies

The ZOOM minimization package

International Nuclear Information System (INIS)

Fischler, Mark S.; Sachs, D.

2004-01-01

A new object-oriented Minimization package is available for distribution in the same manner as CLHEP. This package, designed for use in HEP applications, has all the capabilities of Minuit, but is a re-write from scratch, adhering to modern C++ design principles. A primary goal of this package is extensibility in several directions, so that its capabilities can be kept fresh with as little maintenance effort as possible. This package is distinguished by the priority that was assigned to C++ design issues, and the focus on producing an extensible system that will resist becoming obsolete

Graphical approach for multiple values logic minimization

Science.gov (United States)

Awwal, Abdul Ahad S.; Iftekharuddin, Khan M.

1999-03-01

Multiple valued logic (MVL) is sought for designing high complexity, highly compact, parallel digital circuits. However, the practical realization of an MVL-based system is dependent on optimization of cost, which directly affects the optical setup. We propose a minimization technique for MVL logic optimization based on graphical visualization, such as a Karnaugh map. The proposed method is utilized to solve signed-digit binary and trinary logic minimization problems. The usefulness of the minimization technique is demonstrated for the optical implementation of MVL circuits.

An innovation management approach for renewable energy deployment. The case of solar photovoltaic (PV) technology

International Nuclear Information System (INIS)

Shum, Kwok L.; Watanabe, Chihiro

2009-01-01

In the discussion of renewable energy deployment, one key concern is the various types of barriers that renewable energy needs to overcome before it can make its way into the mainstream. These barriers increasingly shift from the technical to the economic and institutional. The most general types of barriers are due to technological 'lock-out' or to carbon 'lock-in' [. Understanding carbon lock-in. Energy Policy 28(12), 817-830 (Elsevier)]. These barriers necessitate the development of a strategic approach to deploy or introduce renewable energy technology. Existing energy policy has mostly relied upon financial subsidies, market-based instruments such as renewable portfolio standards, and production tax credits to stimulate the installation and use of equipment to generate electricity from renewable sources. These strategies target mostly system-level decisions of end users. The purpose of this paper is to present an innovation perspective on the renewable energy deployment process by introducing the innovation value-added chain (IVC) framework. The analytical objective of IVC is to evaluate the impact of a new innovation on the various stakeholders and players in the development and deployment processes. A deployment or innovation strategy that causes minimal disruption, enhances existing competencies, or expedites new learning by the players has a higher chance to succeed. We draw upon two sets of system integration costs data for grid-connected distributed photovoltaic (PV) systems in Japan and the United States and demonstrate conspicuously different dynamic learning behaviors. These two deployment models can be understood in terms of how the IVCs are organized and how PV system integration projects are performed in the field. In addition, IVC-based findings can inform the targeted application of conventional financial subsidies for learning investment not only at the PV system level, but also at the (localized) system integration level. This would involve

Harm minimization among teenage drinkers

DEFF Research Database (Denmark)

Jørgensen, Morten Hulvej; Curtis, Tine; Christensen, Pia Haudrup

2007-01-01

AIM: To examine strategies of harm minimization employed by teenage drinkers. DESIGN, SETTING AND PARTICIPANTS: Two periods of ethnographic fieldwork were conducted in a rural Danish community of approximately 2000 inhabitants. The fieldwork included 50 days of participant observation among 13....... In regulating the social context of drinking they relied on their personal experiences more than on formalized knowledge about alcohol and harm, which they had learned from prevention campaigns and educational programmes. CONCLUSIONS: In this study we found that teenagers may help each other to minimize alcohol...

Perceived job demands during military deployment : What soldiers say in Afghanistan (abstract)

NARCIS (Netherlands)

Boermans, S.M.; Kamphuis, W.; Delahaij, R.; Euwema, M.

2012-01-01

Military deployment is inherently demanding and military organizations have to prepare their personnel for a broad range of operational demands. So far, it remains unclear how perceptions of operational demands differ between distinct military units. Using a cross-sectional design, this study

Optimizing Automatic Deployment Using Non-functional Requirement Annotations

Science.gov (United States)

Kugele, Stefan; Haberl, Wolfgang; Tautschnig, Michael; Wechs, Martin

Model-driven development has become common practice in design of safety-critical real-time systems. High-level modeling constructs help to reduce the overall system complexity apparent to developers. This abstraction caters for fewer implementation errors in the resulting systems. In order to retain correctness of the model down to the software executed on a concrete platform, human faults during implementation must be avoided. This calls for an automatic, unattended deployment process including allocation, scheduling, and platform configuration.

DESAIN DAN PEMBUATAN ALAT PENGGILING DAGING DENGAN QUALITY FUNCTION DEPLOYMENT

OpenAIRE

Stefanus Ongkodjojo; Charles Anson; Soejono Tjitro

2006-01-01

Quality Function Deployment (QFD) is a powerful development methodology with a wide range of applications. This paper presents a simple case using QFD on the design, detail, and process phase of a Meat Grinder product as a tool of improvement for hygienic of the Meat Grinder. The main purpose of QFD in this study was to apply in construction a method of customer-oriented design used in other industries, and to adapt some of the tables and matrices. Another purpose of this case study was to te...

Free energy minimization to predict RNA secondary structures and computational RNA design.

Science.gov (United States)

Churkin, Alexander; Weinbrand, Lina; Barash, Danny

2015-01-01

Determining the RNA secondary structure from sequence data by computational predictions is a long-standing problem. Its solution has been approached in two distinctive ways. If a multiple sequence alignment of a collection of homologous sequences is available, the comparative method uses phylogeny to determine conserved base pairs that are more likely to form as a result of billions of years of evolution than by chance. In the case of single sequences, recursive algorithms that compute free energy structures by using empirically derived energy parameters have been developed. This latter approach of RNA folding prediction by energy minimization is widely used to predict RNA secondary structure from sequence. For a significant number of RNA molecules, the secondary structure of the RNA molecule is indicative of its function and its computational prediction by minimizing its free energy is important for its functional analysis. A general method for free energy minimization to predict RNA secondary structures is dynamic programming, although other optimization methods have been developed as well along with empirically derived energy parameters. In this chapter, we introduce and illustrate by examples the approach of free energy minimization to predict RNA secondary structures.

Key factors affecting the deployment of electricity generation technologies in energy technology scenarios

International Nuclear Information System (INIS)

Ruoss, F.; Turton, H.; Hirschberg, S.

2009-12-01

This report presents the findings of a survey of key factors affecting the deployment of electricity generation technologies in selected energy scenarios. The assumptions and results of scenarios, and the different models used in their construction, are compared. Particular attention is given to technology assumptions, such as investment cost or capacity factors, and their impact on technology deployment. We conclude that the deployment of available technologies, i.e. their market shares, can only be explained from a holistic perspective, and that there are strong interactions between driving forces and competing technology options within a certain scenario. Already the design of a scenario analysis has important impacts on the deployment of technologies: the choice of the set of available technologies, the modeling approach and the definition of the storylines determine the outcome. Furthermore, the quantification of these storylines into input parameters and cost assumptions drives technology deployment, even though differences across the scenarios in cost assumptions are not observed to account for many of the observed differences in electricity technology deployment. The deployment can only be understood after a consideration of the interplay of technology options and the scale of technology deployment, which is determined by economic growth, end-use efficiency, and electrification. Some input parameters are of particular importance for certain technologies: CO 2 prices, fuel prices and the availability of carbon capture and storage appear to be crucial for the deployment of fossil-fueled power plants; maximum construction rates and safety concerns determine the market share of nuclear power; the availability of suitable sites represents the most important factor for electricity generation from hydro and wind power plants; and technology breakthroughs are needed for solar photovoltaics to become cost-competitive. Finally, this analysis concludes with a review

Key factors affecting the deployment of electricity generation technologies in energy technology scenarios

Energy Technology Data Exchange (ETDEWEB)

Ruoss, F.; Turton, H.; Hirschberg, S.

2009-12-15

This report presents the findings of a survey of key factors affecting the deployment of electricity generation technologies in selected energy scenarios. The assumptions and results of scenarios, and the different models used in their construction, are compared. Particular attention is given to technology assumptions, such as investment cost or capacity factors, and their impact on technology deployment. We conclude that the deployment of available technologies, i.e. their market shares, can only be explained from a holistic perspective, and that there are strong interactions between driving forces and competing technology options within a certain scenario. Already the design of a scenario analysis has important impacts on the deployment of technologies: the choice of the set of available technologies, the modeling approach and the definition of the storylines determine the outcome. Furthermore, the quantification of these storylines into input parameters and cost assumptions drives technology deployment, even though differences across the scenarios in cost assumptions are not observed to account for many of the observed differences in electricity technology deployment. The deployment can only be understood after a consideration of the interplay of technology options and the scale of technology deployment, which is determined by economic growth, end-use efficiency, and electrification. Some input parameters are of particular importance for certain technologies: CO{sub 2} prices, fuel prices and the availability of carbon capture and storage appear to be crucial for the deployment of fossil-fueled power plants; maximum construction rates and safety concerns determine the market share of nuclear power; the availability of suitable sites represents the most important factor for electricity generation from hydro and wind power plants; and technology breakthroughs are needed for solar photovoltaics to become cost-competitive. Finally, this analysis concludes with a

Experiences and recommendations in deploying a real-time, water quality monitoring system

Science.gov (United States)

O'Flynn, B.; Regan, F.; Lawlor, A.; Wallace, J.; Torres, J.; O'Mathuna, C.

2010-12-01

Monitoring of water quality at a river basin level to meet the requirements of the Water Framework Directive (WFD) using conventional sampling and laboratory-based techniques poses a significant financial burden. Wireless sensing systems offer the potential to reduce these costs considerably, as well as provide more useful, continuous monitoring capabilities by giving an accurate idea of the changing environmental and water quality in real time. It is unlikely that the traditional spot/grab sampling will provide a reasonable estimate of the true maximum and/or mean concentration for a particular physicochemical variable in a water body with marked temporal variability. When persistent fluctuations occur, it is likely only to be detected through continuous measurements, which have the capability of detecting sporadic peaks of concentration. Thus, in situ sensors capable of continuous sampling of parameters required under the WFD would therefore provide more up-to-date information, cut monitoring costs and provide better coverage representing long-term trends in fluctuations of pollutant concentrations. DEPLOY is a technology demonstration project, which began planning and station selection and design in August 2008 aiming to show how state-of-the-art technology could be implemented for cost-effective, continuous and real-time monitoring of a river catchment. The DEPLOY project is seen as an important building block in the realization of a wide area autonomous network of sensors capable of monitoring the spatial and temporal distribution of important water quality and environmental target parameters. The demonstration sites chosen are based in the River Lee, which flows through Ireland's second largest city, Cork, and were designed to include monitoring stations in five zones considered typical of significant river systems--these monitor water quality parameters such as pH, temperature, depth, conductivity, turbidity and dissolved oxygen. Over one million data points

Experiences and recommendations in deploying a real-time, water quality monitoring system

International Nuclear Information System (INIS)

O'Flynn, B; O'Mathuna, C; Regan, F; Lawlor, A; Wallace, J; Torres, J

2010-01-01

Monitoring of water quality at a river basin level to meet the requirements of the Water Framework Directive (WFD) using conventional sampling and laboratory-based techniques poses a significant financial burden. Wireless sensing systems offer the potential to reduce these costs considerably, as well as provide more useful, continuous monitoring capabilities by giving an accurate idea of the changing environmental and water quality in real time. It is unlikely that the traditional spot/grab sampling will provide a reasonable estimate of the true maximum and/or mean concentration for a particular physicochemical variable in a water body with marked temporal variability. When persistent fluctuations occur, it is likely only to be detected through continuous measurements, which have the capability of detecting sporadic peaks of concentration. Thus, in situ sensors capable of continuous sampling of parameters required under the WFD would therefore provide more up-to-date information, cut monitoring costs and provide better coverage representing long-term trends in fluctuations of pollutant concentrations. DEPLOY is a technology demonstration project, which began planning and station selection and design in August 2008 aiming to show how state-of-the-art technology could be implemented for cost-effective, continuous and real-time monitoring of a river catchment. The DEPLOY project is seen as an important building block in the realization of a wide area autonomous network of sensors capable of monitoring the spatial and temporal distribution of important water quality and environmental target parameters. The demonstration sites chosen are based in the River Lee, which flows through Ireland's second largest city, Cork, and were designed to include monitoring stations in five zones considered typical of significant river systems-–these monitor water quality parameters such as pH, temperature, depth, conductivity, turbidity and dissolved oxygen. Over one million data

DEVELOPMENT AND DEPLOYMENT OF THE MOBILE ARM RETRIEVAL SYSTEM (MARS) - 12187

Energy Technology Data Exchange (ETDEWEB)

BURKE CA; LANDON MR; HANSON CE

2011-11-08

Washington River Protection Solutions (WRPS) is developing and deploying Mobile Arm Retrieval System (MARS) technologies solutions to support retrieval of radioactive and chemical waste from underground single shell storage tanks (SST) located at the Hanford Site, which is near Richland, Washington. WRPS has developed the MARS using a standardized platform that is capable of deploying multiple retrieval technologies. To date, WRPS, working with their mentor-protege company, Columbia Energy and Environmental Services (CEES), has developed two retrieval mechanisms, MARS-Sluicing (MARS-S) and MARS-Vacuum (MARS-V). MARS-S uses pressurized fluids routed through spray nozzles to mobilize waste materials to a centrally located slurry pump (deployed in 2011). MARS-V uses pressurized fluids routed through an eductor nozzle. The eductor nozzle allows a vacuum to be drawn on the waste materials. The vacuum allows the waste materials to be moved to an in-tank vessel, then extracted from the SST and subsequently pumped to newer and safer double shell tanks (DST) for storage until the waste is treated for disposal. The MARS-S system is targeted for sound SSTs (i.e., non leaking tanks). The MARS-V is targeted for assumed leaking tanks or those tanks that are of questionable integrity. Both versions of MARS are beinglhave been developed in compliance with WRPS's TFC-PLN-90, Technology Development Management Plan [1]. TFC-PLN-90 includes a phased approach to design, testing, and ultimate deployment of new technologies. The MARS-V is scheduled to be deployed in tank 241-C-105 in late 2012.

DEVELOPMENT AND DEPLOYMENT OF THE MOBILE ARM RETRIEVAL SYSTEM (MARS) - 12187

Energy Technology Data Exchange (ETDEWEB)

BURKE CA; LANDON MR; HANSON CE

2012-01-30

Washington River Protection Solutions (WRPS) is developing and deploying Mobile Arm Retrieval System (MARS) technologies solutions to support retrieval of radioactive and chemical waste from underground single shell storage tanks (SST) located at the Hanford Site, which is near Richland, Washington. WRPS has developed the MARS using a standardized platform that is capable of deploying multiple retrieval technologies. To date, WRPS, working with their mentor-protege company, Columbia Energy and Environmental Services (CEES), has developed two retrieval mechanisms, MARS-Sluicing (MARS-S) and MARS-Vacuum (MARS-V). MARS-S uses pressurized fluids routed through spray nozzles to mobilize waste materials to a centrally located slurry pump (deployed in 2011). MARS-V uses pressurized fluids routed through an eductor nozzle. The eductor nozzle allows a vacuum to be drawn on the waste materials. The vacuum allows the waste materials to be moved to an in-tank vessel, then extracted from the SST and subsequently pumped to newer and safer double shell tanks (DST) for storage until the waste is treated for disposal. The MARS-S system is targeted for sound SSTs (i.e., non leaking tanks). The MARS-V is targeted for assumed leaking tanks or those tanks that are of questionable integrity. Both versions of MARS are being/have been developed in compliance with WRPS's TFC-PLN-90, Technology Development Management Plan. TFC-PLN-90 includes a phased approach to design, testing, and ultimate deployment of new technologies. The MARS-V is scheduled to be deployed in tank 241-C-105 in late 2012.

Temperature Switch PCR (TSP: Robust assay design for reliable amplification and genotyping of SNPs

Directory of Open Access Journals (Sweden)

Mather Diane E

2009-12-01

Full Text Available Abstract Background Many research and diagnostic applications rely upon the assay of individual single nucleotide polymorphisms (SNPs. Thus, methods to improve the speed and efficiency for single-marker SNP genotyping are highly desirable. Here, we describe the method of temperature-switch PCR (TSP, a biphasic four-primer PCR system with a universal primer design that permits amplification of the target locus in the first phase of thermal cycling before switching to the detection of the alleles. TSP can simplify assay design for a range of commonly used single-marker SNP genotyping methods, and reduce the requirement for individual assay optimization and operator expertise in the deployment of SNP assays. Results We demonstrate the utility of TSP for the rapid construction of robust and convenient endpoint SNP genotyping assays based on allele-specific PCR and high resolution melt analysis by generating a total of 11,232 data points. The TSP assays were performed under standardised reaction conditions, requiring minimal optimization of individual assays. High genotyping accuracy was verified by 100% concordance of TSP genotypes in a blinded study with an independent genotyping method. Conclusion Theoretically, TSP can be directly incorporated into the design of assays for most current single-marker SNP genotyping methods. TSP provides several technological advances for single-marker SNP genotyping including simplified assay design and development, increased assay specificity and genotyping accuracy, and opportunities for assay automation. By reducing the requirement for operator expertise, TSP provides opportunities to deploy a wider range of single-marker SNP genotyping methods in the laboratory. TSP has broad applications and can be deployed in any animal and plant species.

Security Support in Continuous Deployment Pipeline

DEFF Research Database (Denmark)

Ullah, Faheem; Raft, Adam Johannes; Shahin, Mojtaba

2017-01-01

Continuous Deployment (CD) has emerged as a new practice in the software industry to continuously and automatically deploy software changes into production. Continuous Deployment Pipeline (CDP) supports CD practice by transferring the changes from the repository to production. Since most of the CDP...... penetration tools. Our findings indicate that the applied tactics improve the security of the major components (i.e., repository, continuous integration server, main server) of a CDP by controlling access to the components and establishing secure connections....

A Power Balance Aware Wireless Charger Deployment Method for Complete Coverage in Wireless Rechargeable Sensor Networks

Directory of Open Access Journals (Sweden)

Tu-Liang Lin

2016-08-01

Full Text Available Traditional sensor nodes are usually battery powered, and the limited battery power constrains the overall lifespan of the sensors. Recently, wireless power transmission technology has been applied in wireless sensor networks (WSNs to transmit wireless power from the chargers to the sensor nodes and solve the limited battery power problem. The combination of wireless sensors and wireless chargers forms a new type of network called wireless rechargeable sensor networks (WRSNs. In this research, we focus on how to effectively deploy chargers to maximize the lifespan of a network. In WSNs, the sensor nodes near the sink consume more power than nodes far away from the sink because of frequent data forwarding. This important power unbalanced factor has not been considered, however, in previous charger deployment research. In this research, a power balance aware deployment (PBAD method is proposed to address the power unbalance in WRSNs and to design the charger deployment with maximum charging efficiency. The proposed deployment method is effectively aware of the existence of the sink node that would cause unbalanced power consumption in WRSNs. The simulation results show that the proposed PBAD algorithm performs better than other deployment methods, and fewer chargers are deployed as a result.

Renewable Energy: Policy Considerations for Deploying Renewables

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-07-01

This information paper accompanies the IEA publication Deploying Renewables 2011: Best and Future Policy Practice (IEA, 2011a). It provides more detailed data and analysis on policies for Deploying Renewables, and is intended to complement the main publication. It provides an account of the strategic drivers underpinning renewable energy (RE) technology deployment (energy security, economic development and environment protection) and assesses RE technologies with respect to these drivers, including an estimate of GHG emissions reductions due to RE technologies. The paper also explores the different barriers to deploying renewables at a given stage of market maturity and discusses what tools policy makers can avail of to succeed in removing deployment barriers. An additional topical highlight explores the challenges associated with accelerating the diffusion of RE technologies in developing countries.

Lessons Learned in Deploying the World s Largest Scale Lustre File System

Energy Technology Data Exchange (ETDEWEB)

Dillow, David A [ORNL; Fuller, Douglas [ORNL; Wang, Feiyi [ORNL; Oral, H Sarp [ORNL; Zhang, Zhe [ORNL; Hill, Jason J [ORNL; Shipman, Galen M [ORNL

2010-01-01

The Spider system at the Oak Ridge National Laboratory's Leadership Computing Facility (OLCF) is the world's largest scale Lustre parallel file system. Envisioned as a shared parallel file system capable of delivering both the bandwidth and capacity requirements of the OLCF's diverse computational environment, the project had a number of ambitious goals. To support the workloads of the OLCF's diverse computational platforms, the aggregate performance and storage capacity of Spider exceed that of our previously deployed systems by a factor of 6x - 240 GB/sec, and 17x - 10 Petabytes, respectively. Furthermore, Spider supports over 26,000 clients concurrently accessing the file system, which exceeds our previously deployed systems by nearly 4x. In addition to these scalability challenges, moving to a center-wide shared file system required dramatically improved resiliency and fault-tolerance mechanisms. This paper details our efforts in designing, deploying, and operating Spider. Through a phased approach of research and development, prototyping, deployment, and transition to operations, this work has resulted in a number of insights into large-scale parallel file system architectures, from both the design and the operational perspectives. We present in this paper our solutions to issues such as network congestion, performance baselining and evaluation, file system journaling overheads, and high availability in a system with tens of thousands of components. We also discuss areas of continued challenges, such as stressed metadata performance and the need for file system quality of service alongside with our efforts to address them. Finally, operational aspects of managing a system of this scale are discussed along with real-world data and observations.

Masked Visual Analysis: Minimizing Type I Error in Visually Guided Single-Case Design for Communication Disorders.

Science.gov (United States)

Byun, Tara McAllister; Hitchcock, Elaine R; Ferron, John

2017-06-10

Single-case experimental designs are widely used to study interventions for communication disorders. Traditionally, single-case experiments follow a response-guided approach, where design decisions during the study are based on participants' observed patterns of behavior. However, this approach has been criticized for its high rate of Type I error. In masked visual analysis (MVA), response-guided decisions are made by a researcher who is blinded to participants' identities and treatment assignments. MVA also makes it possible to conduct a hypothesis test assessing the significance of treatment effects. This tutorial describes the principles of MVA, including both how experiments can be set up and how results can be used for hypothesis testing. We then report a case study showing how MVA was deployed in a multiple-baseline across-subjects study investigating treatment for residual errors affecting rhotics. Strengths and weaknesses of MVA are discussed. Given their important role in the evidence base that informs clinical decision making, it is critical for single-case experimental studies to be conducted in a way that allows researchers to draw valid inferences. As a method that can increase the rigor of single-case studies while preserving the benefits of a response-guided approach, MVA warrants expanded attention from researchers in communication disorders.

The deployment of manufacturing flexibility as a function of company strategy

Directory of Open Access Journals (Sweden)

Carla Estorilio

2013-08-01

Full Text Available The flexibility is one of the priorities in manufacturing companies. However, the lack of guidelines for carrying out a critical analysis of the use of resources in manufacturing industry leads to a loss of process performance. This article describes a method to help companies identify the resources needed to provide manufacturing flexibility and meet the demands of their consumers while complying with company strategy. The literature related to flexibility is reviewed and a classification based on four levels is proposed: abilities, dimensions, elements and resources that provide flexibility. Based on this taxonomy and using the principles of QFD (Quality Function Deployment, a method is proposed that shows the correlation between these four levels, starting with customer demand and company strategy. The method was tested in an automobile manufacturing company, showing the applicability of the method. It highlighted the high degree of automation, which’s had serious problems related to restrictions on product mix. It can be inferred that this problem could be minimized by simplifying the tasks involved in the manufacture of car and by hiring more experienced, multi-skilled workers. The proposed method is different from those founded in the literature review because it deploys two levels more of flexibility, considering the QFD structure, and addresses strategic company issues.

Nuclear Reactor Technology Assessment for Near Term Deployment

International Nuclear Information System (INIS)

2013-01-01

One of the IAEA's statutory objectives is to 'seek to accelerate and enlarge the contribution of atomic energy to peace, health and prosperity throughout the world.' One way this objective is achieved is through the publication of a range of technical series. Two of these are the IAEA Nuclear Energy Series and the IAEA Safety Standards Series. According to Article III.A.6 of the IAEA Statute, the safety standards establish 'standards of safety for protection of health and minimization of danger to life and property'. The safety standards include the Safety Fundamentals, Safety Requirements and Safety Guides. These standards are written primarily in a regulatory style, and are binding on the IAEA for its own programmes. The principal users are the regulatory bodies in Member States and other national authorities. The IAEA Nuclear Energy Series comprises reports designed to encourage and assist R and D on, and application of, nuclear energy for peaceful uses. This includes practical examples to be used by owners and operators of utilities in Member States, implementing organizations, academia, and government officials, among others. This information is presented in guides, reports on technology status and advances, and best practices for peaceful uses of nuclear energy based on inputs from international experts. The IAEA Nuclear Energy Series complements the IAEA Safety Standards Series. Several IAEA Member States have embarked recently on initiatives to establish or reinvigorate nuclear power programmes. In response, the IAEA has developed several guidance and technical publications to identify with Member States the complex tasks associated with such an undertaking and to recommend the processes that can be used in the performance of this work. A major challenge in this undertaking, especially for newcomer Member States, is the process associated with reactor technology assessment (RTA) for near term deployment. RTA permits the evaluation, selection and deployment

Efficient Learning Design

DEFF Research Database (Denmark)

Godsk, Mikkel

This paper presents the current approach to implementing educational technology with learning design at the Faculty of Science and Technology, Aarhus University, by introducing the concept of ‘efficient learning design’. The underlying hypothesis is that implementing learning design is more than...... engaging educators in the design process and developing teaching and learning, it is a shift in educational practice that potentially requires a stakeholder analysis and ultimately a business model for the deployment. What is most important is to balance the institutional, educator, and student...... perspectives and to consider all these in conjunction in order to obtain a sustainable, efficient learning design. The approach to deploying learning design in terms of the concept of efficient learning design, the catalyst for educational development, i.e. the learning design model and how it is being used...

Deployment Health Surveillance

National Research Council Canada - National Science Library

DeNicola, Anthony D

2004-01-01

.... Gulf War health questions have resulted in controversy over potentially hazardous exposures during the deployment, the possibility of adverse affects from preventive health measures, and the role...

Separations technologies supporting the development of a deployable ATW system

International Nuclear Information System (INIS)

Laidler, J. J.

2000-01-01

A program has been initiated for the purpose of developing the chemical separations technologies necessary to support a large Accelerator Transmutation of Waste (ATW) system capable of dealing with the projected inventory of spent fuel from the commercial nuclear power stations in the United States. The first several years of the program will be directed toward an elucidation of related technical issues and to the establishment, by means of comprehensive trade studies, of an optimum configuration of the elements of the chemical processing infrastructure required for support of the total ATW system. By adopting this sort of disciplined systems engineering approach, it is expected that development and demonstration costs can be minimized and that it will be possible to deploy an ATW system that is an environmentally sound and economically viable venture

Design and deployment strategies for small and medium sized reactors (SMRs) to overcome loss of economies of scale and incorporate increased proliferation resistance

International Nuclear Information System (INIS)

Kuznetsov, V.

2007-01-01

The designers of innovative small and medium sized reactors pursue new design and deployment strategies making use of certain advantages provided by smaller reactor size and capacity to achieve reduced design complexity and simplified operation and maintenance requirements, and to provide for incremental capacity increase through multi-module plant clustering. Competitiveness of SMRs (Small and Medium size Reactor) depends on the incorporated strategies to overcome loss of economies of scale but equally it depends on finding appropriate market niches for such reactors. For many less developed countries, these are the features of enhanced proliferation resistance and increased robustness of barriers for sabotage protection that may ensure the progress of nuclear power. For such countries, small reactors without on-site refuelling, designed for infrequent replacement of well-contained fuel cassette(s) in a manner that impedes clandestine diversion of nuclear fuel material, may provide a solution. Based on the outputs of recent IAEA activities for innovative SMRs, the paper provides a summary of the state-of-the-art in approaches to improve SMR competitiveness and incorporate enhanced proliferation resistance and energy security. (author)

Performance potential of mechanical ventilation systems with minimized pressure loss

DEFF Research Database (Denmark)

Terkildsen, Søren; Svendsen, Svend

2013-01-01

simulations that quantify fan power consumption, heating demand and indoor environmental conditions. The system was designed with minimal pressure loss in the duct system and heat exchanger. Also, it uses state-of-the-art components such as electrostatic precipitators, diffuse ceiling inlets and demand......In many locations mechanical ventilation has been the most widely used principle of ventilation over the last 50 years but the conventional system design must be revised to comply with future energy requirements. This paper examines the options and describes a concept for the design of mechanical...... ventilation systems with minimal pressure loss and minimal energy use. This can provide comfort ventilation and avoid overheating through increased ventilation and night cooling. Based on this concept, a test system was designed for a fictive office building and its performance was documented using building...

Power allocation strategies to minimize energy consumption in wireless body area networks.

Science.gov (United States)

Kailas, Aravind

2011-01-01

The wide scale deployment of wireless body area networks (WBANs) hinges on designing energy efficient communication protocols to support the reliable communication as well as to prolong the network lifetime. Cooperative communications, a relatively new idea in wireless communications, offers the benefits of multi-antenna systems, thereby improving the link reliability and boosting energy efficiency. In this short paper, the advantages of resorting to cooperative communications for WBANs in terms of minimized energy consumption are investigated. Adopting an energy model that encompasses energy consumptions in the transmitter and receiver circuits, and transmitting energy per bit, it is seen that cooperative transmission can improve energy efficiency of the wireless network. In particular, the problem of optimal power allocation is studied with the constraint of targeted outage probability. Two strategies of power allocation are considered: power allocation with and without posture state information. Using analysis and simulation-based results, two key points are demonstrated: (i) allocating power to the on-body sensors making use of the posture information can reduce the total energy consumption of the WBAN; and (ii) when the channel condition is good, it is better to recruit less relays for cooperation to enhance energy efficiency.

Early identification of posttraumatic stress following military deployment

DEFF Research Database (Denmark)

Karstoft, Karen-Inge; Statnikov, Alexander; Andersen, Søren B

2015-01-01

BACKGROUND: Pre-deployment identification of soldiers at risk for long-term posttraumatic stress psychopathology after home coming is important to guide decisions about deployment. Early post-deployment identification can direct early interventions to those in need and thereby prevents...... the development of chronic psychopathology. Both hold significant public health benefits given large numbers of deployed soldiers, but has so far not been achieved. Here, we aim to assess the potential for pre- and early post-deployment prediction of resilience or posttraumatic stress development in soldiers...... by application of machine learning (ML) methods. METHODS: ML feature selection and prediction algorithms were applied to a prospective cohort of 561 Danish soldiers deployed to Afghanistan in 2009 to identify unique risk indicators and forecast long-term posttraumatic stress responses. RESULTS: Robust pre...

SpRoUTS (Space Robot Universal Truss System): Reversible Robotic Assembly of Deployable Truss Structures of Reconfigurable Length

Science.gov (United States)

Jenett, Benjamin; Cellucci, Daniel; Cheung, Kenneth

2015-01-01

Automatic deployment of structures has been a focus of much academic and industrial work on infrastructure applications and robotics in general. This paper presents a robotic truss assembler designed for space applications - the Space Robot Universal Truss System (SpRoUTS) - that reversibly assembles a truss from a feedstock of hinged andflat-packed components, by folding the sides of each component up and locking onto the assembled structure. We describe the design and implementation of the robot and show that the assembled truss compares favorably with prior truss deployment systems.

The minimally tuned minimal supersymmetric standard model

International Nuclear Information System (INIS)

Essig, Rouven; Fortin, Jean-Francois

2008-01-01

The regions in the Minimal Supersymmetric Standard Model with the minimal amount of fine-tuning of electroweak symmetry breaking are presented for general messenger scale. No a priori relations among the soft supersymmetry breaking parameters are assumed and fine-tuning is minimized with respect to all the important parameters which affect electroweak symmetry breaking. The superpartner spectra in the minimally tuned region of parameter space are quite distinctive with large stop mixing at the low scale and negative squark soft masses at the high scale. The minimal amount of tuning increases enormously for a Higgs mass beyond roughly 120 GeV

An analysis of the deployment of a pumpkin balloon at Mars

Science.gov (United States)

Rand, J. L.; Phillips, M. L.

2004-01-01

The design of large superpressure balloons has received significant attention in recent years due to the successful demonstration of various enabling technologies and materials. Of particular note is the "pumpkin" shaped balloon concept, which allows the stress in the envelope to be limited by the surface geometry. Unlike a sphere, where the radius used to determine the stress is determined by the volume of the balloon, the pumpkin utilizes a system of meridional tendons to react the loading in one direction, and form a number of lobes, which limit the stress in the circumferential direction. A suitable superpressure balloon has been designed using this technology which will carry 2 kg in the atmosphere of Mars. The deployment of this balloon is assumed to occur while falling on a decelerator suitably designed for the Mars atmosphere. The inflation is accomplished by a 10 kg system suspended at the nadir of the balloon. As the system falls toward the surface of the planet, helium gas is transferred into the balloon, forming a partially inflated system very similar to an ascending zero pressure balloon. This analysis incorporates the flow of the planetary gas around the inflating balloon which alters the pressure distribution and shape. As a result, stresses are seen to increase beyond the design values which will require the balloon to be redesigned to accommodate this type of dynamic deployment.

Deployable bamboo structure project: A building life-cycle report

Science.gov (United States)

Firdaus, Adrian; Prastyatama, Budianastas; Sagara, Altho; Wirabuana, Revian N.

2017-11-01

Bamboo is considered as a sustainable material in the world of construction, and it is vastly available in Indonesia. The general utilization of the material is increasingly frequent, however, its usage as a deployable structure-a recently-developed use of bamboo, is still untapped. This paper presents a report on a deployable bamboo structure project, covering the entire building life-cycle phase. The cycle encompasses the designing; fabrication; transportation; construction; operation and maintenance; as well as a plan for future re-use. The building is made of a configuration of the structural module, each being a folding set of bars which could be reduced in size to fit into vehicles for easy transportation. Each structural module was made of Gigantochloa apus bamboo. The fabrication, transportation, and construction phase require by a minimum of three workers. The fabrication and construction phase require three hours and fifteen minutes respectively. The building is utilized as cafeteria stands, the operation and maintenance phase started since early March 2017. The maintenance plan is scheduled on a monthly basis, focusing on the inspection of the locking mechanism element and the entire structural integrity. The building is designed to allow disassembly process so that it is reusable in the future.

Climate, air quality and human health benefits of various solar photovoltaic deployment scenarios in China in 2030

Science.gov (United States)

Yang, Junnan; Li, Xiaoyuan; Peng, Wei; Wagner, Fabian; Mauzerall, Denise L.

2018-06-01

Solar photovoltaic (PV) electricity generation can greatly reduce both air pollutant and greenhouse gas emissions compared to fossil fuel electricity generation. The Chinese government plans to greatly scale up solar PV installation between now and 2030. However, different PV development pathways will influence the range of air quality and climate benefits. Benefits depend on how much electricity generated from PV is integrated into power grids and the type of power plant displaced. Using a coal-intensive power sector projection as the base case, we estimate the climate, air quality, and related human health benefits of various 2030 PV deployment scenarios. We use the 2030 government goal of 400 GW installed capacity but vary the location of PV installation and the extent of inter-provincial PV electricity transmission. We find that deploying distributed PV in the east with inter-provincial transmission maximizes potential CO2 reductions and air quality-related health benefits (4.2% and 1.2% decrease in national total CO2 emissions and air pollution-related premature deaths compared to the base case, respectively). Deployment in the east with inter-provincial transmission results in the largest benefits because it maximizes displacement of the dirtiest coal-fired power plants and minimizes PV curtailment, which is more likely to occur without inter-provincial transmission. We further find that the maximum co-benefits achieved with deploying PV in the east and enabling inter-provincial transmission are robust under various maximum PV penetration levels in both provincial and regional grids. We find large potential benefits of policies that encourage distributed PV deployment and facilitate inter-provincial PV electricity transmission in China.

Deploying Renewables - Best and Future Policy Practice

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-11-23

The global energy system faces urgent challenges. Concerns about energy security are growing, as highlighted by the recent political turmoil in Northern Africa and the nuclear incident in Fukushima. At the same time, the need to respond to climate change is more critical than ever. Against this background, many governments have increased efforts to promote deployment of renewable energy -- low-carbon sources that can strengthen energy security. This has stimulated unprecedented rise in deployment, and renewables are now the fastest growing sector of the energy mix. This 'coming of age' of renewable energy also brings challenges. Growth is focused on a few of the available technologies, and rapid deployment is confined to a relatively small number of countries. In more advanced markets, managing support costs and system integration of large shares of renewable energy in a time of economic weakness and budget austerity has sparked vigorous political debate. The IEA's new report, Deploying Renewables 2011: Best and Future Policy Practice: - Provides a comprehensive review and analysis of renewable energy policy and market trends; - Analyses in detail the dynamics of deployment and provides best-practice policy principles for different stages of market maturity; - Assesses the impact and cost-effectiveness of support policies using new methodological tools and indicators; - Investigates the strategic reasons underpinning the pursuit of RE deployment by different countries and the prospects for globalisation of RE. This new book builds on and extends a 2008 IEA publication, drawing on recent policy and deployment experience world-wide. It provides guidance for policy makers and other stakeholders to avoid past mistakes, overcome new challenges and reap the benefits of deploying renewables -- today and tomorrow.

An interactive audio-visual installation using ubiquitous hardware and web-based software deployment

Directory of Open Access Journals (Sweden)

Tiago Fernandes Tavares

2015-05-01

Full Text Available This paper describes an interactive audio-visual musical installation, namely MOTUS, that aims at being deployed using low-cost hardware and software. This was achieved by writing the software as a web application and using only hardware pieces that are built-in most modern personal computers. This scenario implies in specific technical restrictions, which leads to solutions combining both technical and artistic aspects of the installation. The resulting system is versatile and can be freely used from any computer with Internet access. Spontaneous feedback from the audience has shown that the provided experience is interesting and engaging, regardless of the use of minimal hardware.

Modeling EERE Deployment Programs

Energy Technology Data Exchange (ETDEWEB)

Cort, Katherine A.; Hostick, Donna J.; Belzer, David B.; Livingston, Olga V.

2007-11-08

The purpose of this report is to compile information and conclusions gathered as part of three separate tasks undertaken as part of the overall project, “Modeling EERE Deployment Programs,” sponsored by the Planning, Analysis, and Evaluation office within the Department of Energy’s Office of Energy Efficiency and Renewable Energy (EERE). The purpose of the project was to identify and characterize the modeling of deployment programs within the EERE Technology Development (TD) programs, address improvements to modeling in the near term, and note gaps in knowledge where future research is needed.

Deployment Health Surveillance

National Research Council Canada - National Science Library

DeNicola, Anthony D

2004-01-01

... of stress in causing chronic illness. The lack of comprehensive deployment health surveillance has made it difficult to determine possible causes of adverse health effects reported by Gulf War veterans...

Deployment technique that takes advantage of the characteristics of Enterprise VRD2: an in vitro study.

Science.gov (United States)

Chihara, Hideo; Ishii, Akira; Kikuchi, Takayuki; Ikeda, Hiroyuki; Arai, Daisuke; Miyamoto, Susumu

2017-10-01

Enterprise VRD, a stent frequently used to assist coil embolization of cerebral aneurysms, has been upgraded to reduce the risk of incomplete stent apposition (ISA), a known risk factor for thromboembolic complications. To compare the performances of Enterprise VRD and Enterprise VRD2 in curved vessels, and to investigate a deployment method that takes advantage of the features of Enterprise VRD2 to achieve better vessel wall apposition. A silicone vascular model connected to a temperature-adjustable perfusion circuit was used. First, Enterprise VRD and Enterprise VRD2 were deployed under fluoroscopy and then ISA was evaluated as the stent cross-sectional area ratio at the curved segment of the vessel. For the measurements, each stent was deployed in vessels with different angles of curvature. Second, the incidence of ISA after insertion of Enterprise VRD2 by the 'pushing over outer curve technique', in which stents are deployed along the outer curve of vessels with continuous wire advancement, was compared with 'Heller's push and pull technique'. For all stents, the cross-sectional area ratio decreased with acute curvature of the vessel. Comparisons of the two stents showed that Enterprise VRD2 was better than Enterprise VRD in maintaining a greater cross-sectional area ratio in curved vessels. In addition, kinking with an acute curvature was also minimized with Enterprise VRD2. Furthermore, ISA was reduced using our technique with Enterprise VRD2. Enterprise VRD2 is superior to Enterprise VRD in reducing ISA in curved vessels and can alter ISA according to the deployment technique used. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

A compact self-recording pressure based sea level gauge suitable for deployments at harbour and offshore environments

Digital Repository Service at National Institute of Oceanography (India)

Desa, E.; Peshwe, V.B.; Joseph, A.; Mehra, P.; Naik, G.P.; Kumar, V.; Desa, E.S.; Desai, R.G.P.; Nagvekar, S.; Desai, S.P.

A compact and lightweight self-recording pressure based sea level gauge has been designed to suit deployments from harbour and offshore environments. A novel hydraulic coupling device designed in-house was used to transfer the seawater pressure...

Deployment-related risk factors of low back pain

DEFF Research Database (Denmark)

Nissen, Lars Ravnborg; Marott, Jacob Louis; Gyntelberg, Finn

2014-01-01

Where much is known about the consequences of spinal and low back pain (LBP) during military deployments, there is lesser knowledge of risk factors for LBP among the deployed forces. The objective of this study was to identify deployment-related exposures associated with LBP. The study was a ques...... their subordinates and involve medical personnel, especially deployed physiotherapists, by giving advice to soldiers of different military occupational specialties on how to optimize ergonomics at work....

IRIS Nuclear Power Plant design

International Nuclear Information System (INIS)

Carelli, M. D.; Cobian, J.

2002-01-01

IRIS(International Reactor Innovative and Secure) is a novel light water reactor with a modular, integral primary system configuration. This concept, initially developed in response to the first NERI solicitation, is now being pursued by an international consortium of 20 participants from seven countries. IRIS is designed to satisfy the four key requirements for Generation IV systems: enhanced safety, improved economics, proliferation resistance and waste minimization. Its main features are: small-to-medium power (100-335 MWe/module); long life core 5 to 10 years) without shuffling or refueling; optimized maintenance with repair shutdown intervals of a least four years; simplified compact design with the primary vessel housing steam generators, pressurizer and pumps; safety by design where accidents are positively eliminated by design rather than engineering to cope with their consequences; loss of coolant accidents of any size and loss of low accidents are eliminated as major safety concerns; estimated power generation total cost is projected to be competitive with other power options. IRIS is one of four new reactor designs currently under NRC review. Projected schedule calls for design certification by 2008 and being ready for deployment by 2001 or later. This rather short schedule is made possible by the fact that IRIS is based on proven light water technology and new technology development is not required. (Author)

The minimal non-minimal standard model

International Nuclear Information System (INIS)

Bij, J.J. van der

2006-01-01

In this Letter I discuss a class of extensions of the standard model that have a minimal number of possible parameters, but can in principle explain dark matter and inflation. It is pointed out that the so-called new minimal standard model contains a large number of parameters that can be put to zero, without affecting the renormalizability of the model. With the extra restrictions one might call it the minimal (new) non-minimal standard model (MNMSM). A few hidden discrete variables are present. It is argued that the inflaton should be higher-dimensional. Experimental consequences for the LHC and the ILC are discussed

Comprehensive Deployment Method for Technical Characteristics Base on Multi-failure Modes Correlation Analysis

Science.gov (United States)

Zheng, W.; Gao, J. M.; Wang, R. X.; Chen, K.; Jiang, Y.

2017-12-01

This paper put forward a new method of technical characteristics deployment based on Reliability Function Deployment (RFD) by analysing the advantages and shortages of related research works on mechanical reliability design. The matrix decomposition structure of RFD was used to describe the correlative relation between failure mechanisms, soft failures and hard failures. By considering the correlation of multiple failure modes, the reliability loss of one failure mode to the whole part was defined, and a calculation and analysis model for reliability loss was presented. According to the reliability loss, the reliability index value of the whole part was allocated to each failure mode. On the basis of the deployment of reliability index value, the inverse reliability method was employed to acquire the values of technology characteristics. The feasibility and validity of proposed method were illustrated by a development case of machining centre’s transmission system.

Scalable and fail-safe deployment of the ATLAS Distributed Data Management system Rucio

CERN Document Server

Lassnig, Mario; The ATLAS collaboration; Barisits, Martin-Stefan; Beermann, Thomas Alfons; Serfon, Cedric; Garonne, Vincent

2015-01-01

This contribution details the deployment of Rucio, the ATLAS Distributed Data Management system. The main complication is that Rucio interacts with a wide variety of external services, and connects globally distributed data centres under different technological and administrative control, at an unprecedented data volume. It is therefore not possibly to create a duplicate instance of Rucio for testing or integration. Every software upgrade or configuration change is thus potentially disruptive and requires fail-safe software and automatic error recovery. Rucio uses a three-layer scaling and mitigation strategy based on quasi-realtime monitoring. This strategy mainly employs independent stateless services, automatic failover, and service migration. The technologies used for deployment and mitigation include OpenStack, Puppet, Graphite, HAProxy, Apache, and nginx. In this contribution, the reasons and design decisions for the deployment, the actual implementation, and an evaluation of all involved services and c...

Family Reintegration Following Guard Deployment

Science.gov (United States)

2010-09-20

Somalia Peacekeepers. Journal of Consulting and Clinical Psychology, 72(5), 909-913. Haas DM . Pazdernik LA. Olsen CH. A cross-sectional survey of the...relationship between partner deployment and stress in pregnancy during wartime. Haas DM . Pazdernik LA. Partner deployment and stress in pregnant...Identify 3-5 key words relating to the proposal. (Required) I used MESH Headings instead of the CRISP Thesaurus for key

Technological innovation in the energy sector: R and D, deployment, and learning-by-doing

International Nuclear Information System (INIS)

Sagar, Ambuj D.; Zwaan, Bob van der

2006-01-01

Technological innovation is fundamental for rendering the energy economy cleaner and more efficient with concomitant economic, developmental, and environmental benefits. This paper discusses aspects of R and D and 'learning-by-doing,' the main contributors to technological change that are complementary yet inter-linked. The relationship between the level of national energy R and D investments and changes in the trajectory of the country's energy system is complex; targeted efforts to promote deployment of new energy technologies play a major role in translating the results of R and D activities to changes in the energy system. Learning-by-doing is an important element of deployment, but it remains largely poorly understood. Hence this phenomenon needs to be 'unpacked' and its various aspects analyzed in detail, so as to allow better design of early deployment efforts to enhance learning gains. This paper highlights how public R and D and deployment efforts must work in tandem to expand the portfolio, and realize the potential, of new and improved energy technologies

Correction: General optimization procedure towards the design of a new family of minimal parameter spin-component-scaled double-hybrid density functional theory.

Science.gov (United States)

Roch, Loïc M; Baldridge, Kim K

2018-02-07

Correction for 'General optimization procedure towards the design of a new family of minimal parameter spin-component-scaled double-hybrid density functional theory' by Loïc M. Roch and Kim K. Baldridge, Phys. Chem. Chem. Phys., 2017, 19, 26191-26200.

Heterogeneous Deployment Analysis for Cost-Effective Mobile Network Evolution

DEFF Research Database (Denmark)

Coletti, Claudio

2013-01-01

network coverage and boosting network capacity in traffic hot-spot areas. The thesis deals with the deployment of both outdoor small cells and indoor femto cells. Amongst the outdoor solution, particular emphasis is put on relay base stations as backhaul costs can be reduced by utilizing LTE spectrum...... statistical models of deployment areas, the performance analysis is carried out in the form of operator case studies for large-scale deployment scenarios, including realistic macro network layouts and inhomogeneous spatial traffic distributions. Deployment of small cells is performed by means of proposed...... heuristic deployment algorithms, which combine network coverage and spatial user density information. As a secondary aspect, deployment solutions achieving the same coverage performance are compared in terms of Total Cost of Ownership (TCO), in order to investigate the viability of different deployment...

Quality function deployment for buildable and sustainable construction

CERN Document Server

Natee, Singhaputtangkul; Teo, Evelyn A L

2016-01-01

This book focuses on the implementation of Quality Function Deployment (QFD) in the construction industry as a tool to help building designers arrive at optimal decisions for external envelope systems with sustainable and buildable design goals. In particular, the book integrates special features into the conventional QFD tool to enhance its performance. These features include a fuzzy multi-criteria decision-making method, fuzzy consensus scheme, and Knowledge Management System (KMS). This integration results in a more robust decision support tool, known as the Knowledge-based Decision Support System QFD (KBDSS-QFD) tool. As an example, the KBDSS-QFD tool is used for the assessment of building envelope materials and designs for high-rise residential buildings in Singapore in the early design stage. The book provides the reader with a conceptual framework for understanding the development of the KBDSS-QFD tool. The framework is presented in a generalized form in order to benefit building professionals, decisio...

Deployment Effects of Marine Renewable Energy Technologies: Wave Energy Scenarios

Energy Technology Data Exchange (ETDEWEB)

Mirko Previsic

2010-06-17

Given proper care in siting, design, deployment, operation and maintenance, wave energy conversion could become one of the more environmentally benign sources of electricity generation. In order to accelerate the adoption of these emerging hydrokinetic and marine energy technologies, navigational and environmental concerns must be identified and addressed. All developing hydrokinetic projects involve a wide variety of stakeholders. One of the key issues that site developers face as they engage with this range of stakeholders is that, due to a lack of technical certainty, many of the possible conflicts (e.g., shipping and fishing) and environmental issues are not well-understood,. In September 2008, re vision consulting, LLC was selected by the Department of Energy (DoE) to apply a scenario-based assessment to the emerging hydrokinetic technology sector in order to evaluate the potential impact of these technologies on the marine environment and navigation constraints. The project’s scope of work includes the establishment of baseline scenarios for wave and tidal power conversion at potential future deployment sites. The scenarios capture variations in technical approaches and deployment scales to properly identify and characterize environmental effects and navigational effects. The goal of the project is to provide all stakeholders with an improved understanding of the potential range of technical attributes and potential effects of these emerging technologies and focus all stakeholders on the critical issues that need to be addressed. By identifying and addressing navigational and environmental concerns in the early stages of the industry’s development, serious mistakes that could potentially derail industry-wide development can be avoided. This groundwork will also help in streamlining siting and associated permitting processes, which are considered key hurdles for the industry’s development in the U.S. today. Re vision is coordinating its efforts with two

Technological developments for ultra-lightweight, large aperture, deployable mirror for space telescopes

Science.gov (United States)

Zuccaro Marchi, Alessandro; D'Amato, Francesco; Gallieni, Daniele; Biasi, Roberto; Molina, Marco; Duò, Fabrizio; Ruder, Nikolaus; Salinari, Piero; Lisi, Franco; Riccardi, Armando; Gambicorti, Lisa; Simonetti, Francesca; Pereira do Carmo, Joao Pedro N.

2017-11-01

The increasing interest on space telescopes for scientific applications leads to implement the manufacturing technology of the most critical element, i.e. the primary mirror: being more suitable a large aperture, it must be lightweight and deployable. The presented topic was originally addressed to a spaceborne DIAL (Differential Absorption LIDAR) mission operating at 935.5 nm for the measurement of water vapour profile in atmosphere, whose results were presented at ICSO 2006 and 2008. Aim of this paper is to present the latest developments on the main issues related to the fabrication of a breadboard, covering two project critical areas identified during the preliminary studies: the design and performances of the long-stroke actuators used to implement the mirror active control and the mirror survivability to launch via Electrostatic Locking (EL) between mirror and backplane. The described work is developed under the ESA/ESTEC contract No. 22321/09/NL/RA. The lightweight mirror is structured as a central sector surrounded by petals, all of them actively controlled to reach the specified shape after initial deployment and then maintained within specs for the entire mission duration. The presented study concerns: a) testing the Carbon Fiber Reinforced Plastic (CFRP) backplane manufacturing and EL techniques, with production of suitable specimens; b) actuator design optimisation; c) design of the deployment mechanism including a high precision latch; d) the fabrication of thin mirrors mock-ups to validate the fabrication procedure for the large shells. The current activity aims to the construction of an optical breadboard capable of demonstrating the achievement of all these coupled critical aspects: optical quality of the thin shell mirror surface, actuators performances and back-plane - EL subsystem functionality.

Efficient Deployment of Key Nodes for Optimal Coverage of Industrial Mobile Wireless Networks

Science.gov (United States)

Li, Xiaomin; Li, Di; Dong, Zhijie; Hu, Yage; Liu, Chengliang

2018-01-01

In recent years, industrial wireless networks (IWNs) have been transformed by the introduction of mobile nodes, and they now offer increased extensibility, mobility, and flexibility. Nevertheless, mobile nodes pose efficiency and reliability challenges. Efficient node deployment and management of channel interference directly affect network system performance, particularly for key node placement in clustered wireless networks. This study analyzes this system model, considering both industrial properties of wireless networks and their mobility. Then, static and mobile node coverage problems are unified and simplified to target coverage problems. We propose a novel strategy for the deployment of clustered heads in grouped industrial mobile wireless networks (IMWNs) based on the improved maximal clique model and the iterative computation of new candidate cluster head positions. The maximal cliques are obtained via a double-layer Tabu search. Each cluster head updates its new position via an improved virtual force while moving with full coverage to find the minimal inter-cluster interference. Finally, we develop a simulation environment. The simulation results, based on a performance comparison, show the efficacy of the proposed strategies and their superiority over current approaches. PMID:29439439

Legionellosis prevention in building water and HVAC systems a practical guide for design, operation and maintenance to minimize the risk

CERN Document Server

Joppolo, Cesare Maria; Pitera, Luca Alberto; Angermann, Jean Pierre; Izard, Mark

2013-01-01

This Guidebook is a practical guide for design, operation and maintenance to minimize the risk of legionellosis in building water and HVAC systmes. It is devided into several themes such as: Air conditioning of the air (by water – humidification), Production of hot water for washing (fundamentally but not only hot water for washing) and Evaporative cooling tower.

Deployable Plume and Aerosol Release Prediction and Tracking System. Nuclear Non-Proliferation Task 1. Final Report

Energy Technology Data Exchange (ETDEWEB)

Kleppe, John; Norris, William; Etezadi, Mehdi

2006-07-19

This contract was awarded in response to a proposal in which a deployable plume and aerosol release prediction and tracking system would be designed, fabricated, and tested. The system would gather real time atmospheric data and input it into a real time atmospheric model that could be used for plume predition and tracking. The system would be able to be quickly deployed by aircraft to points of interest or positioned for deployment by vehicles. The system would provide three dimensional (u, v, and w) wind vector data, inversion height measurements, surface wind information, classical weather station data, and solar radiation. The on-board real time computer model would provide the prediction of the behavior of plumes and released aerosols.

Discrete Curvatures and Discrete Minimal Surfaces

KAUST Repository

Sun, Xiang

2012-01-01

This thesis presents an overview of some approaches to compute Gaussian and mean curvature on discrete surfaces and discusses discrete minimal surfaces. The variety of applications of differential geometry in visualization and shape design leads

Home front: post-deployment mental health and divorces.

Science.gov (United States)

Negrusa, Brighita; Negrusa, Sebastian

2014-06-01

Since 2003, about 14 % of U.S. Army soldiers have reported symptoms of posttraumatic stress disorder (PTSD) following deployments. In this article, we examine how post-deployment symptoms of PTSD and of other mental health conditions are related to the probability of divorce among married active-duty U.S. Army soldiers. For this purpose, we combine Army administrative individual-level longitudinal data on soldiers' deployments, marital history, and sociodemographic characteristics with their self-reported post-deployment health information. Our estimates indicate that time spent in deployment increases the divorce risk among Army enlisted personnel and that PTSD symptoms are associated with further increases in the odds of divorce. Although officers are generally less likely to screen positive for PTSD than enlisted personnel, we find a stronger relationship between PTSD symptoms and divorces among Army officers who are PTSD-symptomatic than among enlisted personnel. We estimate a larger impact of deployments on the divorce risk among female soldiers, but we do not find a differential impact of PTSD symptoms by gender. Also, we find that most of the effect of PTSD symptoms occurs early in the career of soldiers who deploy multiple times.

Minimizing deviant behavior in healthcare organizations: the effects of supportive leadership and job design.

Science.gov (United States)

Chullen, C Logan; Dunford, Benjamin B; Angermeier, Ingo; Boss, R Wayne; Boss, Alan D

2010-01-01

In an era when healthcare organizations are beset by intense competition, lawsuits, and increased administrative costs, it is essential that employees perform their jobs efficiently and without distraction. Deviant workplace behavior among healthcare employees is especially threatening to organizational effectiveness, and healthcare managers must understand the antecedents of such behavior to minimize its prevalence. Deviant employee behavior has been categorized into two major types, individual and organizational, according to the intended target of the behavior. Behavior directed at the individual includes such acts as harassment and aggression, whereas behavior directed at the organization includes such acts as theft, sabotage, and voluntary absenteeism, to name a few (Robinson and Bennett 1995). Drawing on theory from organizational behavior, we examined two important features of supportive leadership, leader-member exchange (LMX) and perceived organizational support (POS), and two important features of job design, intrinsic motivation and depersonalization, as predictors of subsequent deviant behavior in a sample of over 1,900 employees within a large US healthcare organization. Employees who reported weaker perceptions of LMX and greater perceptions of depersonalization were more likely to engage in deviant behavior directed at the individual, whereas employees who reported weaker perceptions of POS and intrinsic motivation were more likely to engage in deviant behavior directed at the organization. These findings give rise to specific prescriptions for healthcare managers to prevent or minimize the frequency of deviant behavior in the workplace.

Technology Development And Deployment Of Systems For The Retrieval And Processing Of Remote-Handled Sludge From Hanford K-West Fuel Storage Basin

International Nuclear Information System (INIS)

Raymond, R.E.

2011-01-01

In 2011, significant progress was made in developing and deploying technologies to remove, transport, and interim store remote-handled sludge from the 105-K West Fuel Storage Basin on the Hanford Site in south-central Washington State. The sludge in the 105-K West Basin is an accumulation of degraded spent nuclear fuel and other debris that collected during long-term underwater storage of the spent fuel. In 2010, an innovative, remotely operated retrieval system was used to successfully retrieve over 99.7% of the radioactive sludge from 10 submerged temporary storage containers in the K West Basin. In 2011, a full-scale prototype facility was completed for use in technology development, design qualification testing, and operator training on systems used to retrieve, transport, and store highly radioactive K Basin sludge. In this facility, three separate systems for characterizing, retrieving, pretreating, and processing remote-handled sludge were developed. Two of these systems were successfully deployed in 2011. One of these systems was used to pretreat knockout pot sludge as part of the 105-K West Basin cleanup. Knockout pot sludge contains pieces of degraded uranium fuel ranging in size from 600 μm to 6350 μm mixed with pieces of inert material, such as aluminum wire and graphite, in the same size range. The 2011 pretreatment campaign successfully removed most of the inert material from the sludge stream and significantly reduced the remaining volume of knockout pot product material. Removing the inert material significantly minimized the waste stream and reduced costs by reducing the number of transportation and storage containers. Removing the inert material also improved worker safety by reducing the number of remote-handled shipments. Also in 2011, technology development and final design were completed on the system to remove knockout pot material from the basin and transport the material to an onsite facility for interim storage. This system is scheduled

Design of Orthogonal Filtered Multitone Modulation Systems and Comparison among Efficient Realizations

Directory of Open Access Journals (Sweden)

Moret Nicola

2010-01-01

Full Text Available Abstract We address the efficient realization of a filtered multitone (FMT modulation system and its orthogonal design. FMT modulation can be viewed as a Discrete Fourier Transform (DFT modulated filter bank (FB. It generalizes the popular orthogonal frequency division multiplexing (OFDM scheme by deploying frequency confined subchannel pulses. We compare three realizations that have been described by Cvetković and Vetterli (1998, and Weiss and Stewart (2000, and Tonello (2006. A detailed derivation of them is performed in the time-domain via the exploitation of different FB polyphase decompositions. We then consider the design of an orthogonal FMT system and we exploit the third realization which allows simplifying the orthogonal FB design and obtaining a block diagonal system matrix with independent subblocks. A numerical method is then presented to obtain an orthogonal FB with well frequency confined subchannel pulses for arbitrarily large number of subchannels. Several examples of pulses with minimal length are reported and their performance is evaluated in typical multipath fading channels. Finally, we compare the orthogonal FMT system with a cyclically prefixed OFDM system in the IEEE 802.11 wireless LAN channel. In this scenario, FMT with minimal length pulses and single tap subchannel equalization outperforms the OFDM system in achievable rate.

Design of Orthogonal Filtered Multitone Modulation Systems and Comparison among Efficient Realizations

Directory of Open Access Journals (Sweden)

Andrea M. Tonello

2010-01-01

Full Text Available We address the efficient realization of a filtered multitone (FMT modulation system and its orthogonal design. FMT modulation can be viewed as a Discrete Fourier Transform (DFT modulated filter bank (FB. It generalizes the popular orthogonal frequency division multiplexing (OFDM scheme by deploying frequency confined subchannel pulses. We compare three realizations that have been described by Cvetković and Vetterli (1998, and Weiss and Stewart (2000, and Tonello (2006. A detailed derivation of them is performed in the time-domain via the exploitation of different FB polyphase decompositions. We then consider the design of an orthogonal FMT system and we exploit the third realization which allows simplifying the orthogonal FB design and obtaining a block diagonal system matrix with independent subblocks. A numerical method is then presented to obtain an orthogonal FB with well frequency confined subchannel pulses for arbitrarily large number of subchannels. Several examples of pulses with minimal length are reported and their performance is evaluated in typical multipath fading channels. Finally, we compare the orthogonal FMT system with a cyclically prefixed OFDM system in the IEEE 802.11 wireless LAN channel. In this scenario, FMT with minimal length pulses and single tap subchannel equalization outperforms the OFDM system in achievable rate.

Design of Orthogonal Filtered Multitone Modulation Systems and Comparison among Efficient Realizations

Science.gov (United States)

Moret, Nicola; Tonello, Andrea M.

2010-12-01

We address the efficient realization of a filtered multitone (FMT) modulation system and its orthogonal design. FMT modulation can be viewed as a Discrete Fourier Transform (DFT) modulated filter bank (FB). It generalizes the popular orthogonal frequency division multiplexing (OFDM) scheme by deploying frequency confined subchannel pulses. We compare three realizations that have been described by Cvetković and Vetterli (1998), and Weiss and Stewart (2000), and Tonello (2006). A detailed derivation of them is performed in the time-domain via the exploitation of different FB polyphase decompositions. We then consider the design of an orthogonal FMT system and we exploit the third realization which allows simplifying the orthogonal FB design and obtaining a block diagonal system matrix with independent subblocks. A numerical method is then presented to obtain an orthogonal FB with well frequency confined subchannel pulses for arbitrarily large number of subchannels. Several examples of pulses with minimal length are reported and their performance is evaluated in typical multipath fading channels. Finally, we compare the orthogonal FMT system with a cyclically prefixed OFDM system in the IEEE 802.11 wireless LAN channel. In this scenario, FMT with minimal length pulses and single tap subchannel equalization outperforms the OFDM system in achievable rate.

Computer-aided dispatch--traffic management center field operational test final evaluation plan : WSDOT deployment

Science.gov (United States)

2003-09-22

This document presents the Evaluation Teams plan for conducting the evaluation of the FOT in Washington State. A companion document exists for the evaluation of the Utah deployment. This plan includes the experimental design for testing hypotheses...

Do soldiers seek more mental health care after deployment? Analysis of mental health consultations in the Netherlands Armed Forces following deployment to Afghanistan

Directory of Open Access Journals (Sweden)

Elisabeth (Liesbeth M. Taal

2014-08-01

Full Text Available Background: Military deployment to combat zones puts military personnel to a number of physical and mental challenges that may adversely affect mental health. Until now, few studies have been performed in Europe on mental health utilization after military deployment. Objective: We compared the incidence of mental health consultations with the Military Mental Health Service (MMHS of military deployed to Afghanistan to that of non-deployed military personnel. Method: We assessed utilization of the MMHS by the full cohort of the Netherlands Armed Forces enlisted between 2008 and 2010 through linkage of mental health and human resource information systems. Results: The total population consisted of 50,508 military (18,233 deployed, 32,275 non-deployed, who accounted for 1,906 new consultations with the MMHS. The follow-up was limited to the first 2 years following deployment. We observed higher mental health care utilization in deployed vs. non-deployed military personnel; hazard ratio (HR, adjusted for sex, military branch and time in service, 1.84 [95% CI 1.61–2.11] in the first and 1.28 [1.09–1.49] in the second year after deployment. An increased risk of adjustment disorders (HR 2.59 [2.02–3.32] and 1.74 [1.30–2.32] and of anxiety disorders (2.22 [1.52–3.25] and 2.28 [1.50–3.45] including posttraumatic stress disorder (5.15 [2.55–10.40] and 5.28 [2.42–11.50], but not of mood disorders (1.33 [0.90–1.97] and 1.11 [0.68–1.82], was observed in deployed personnel in the first- and second-year post-deployment, respectively. Military personnel deployed in a unit with a higher risk of confrontation with potentially traumatic events had a higher HR (2.13 [1.84–2.47] and 1.40 [1.18–1.67]. Conclusions: Though absolute risk was low, in the first and second year following deployment to Afghanistan there was an 80 and 30% higher risk for mental health problems resulting in a consultation with the Dutch MMHS compared to military never

Do soldiers seek more mental health care after deployment? Analysis of mental health consultations in the Netherlands Armed Forces following deployment to Afghanistan

Science.gov (United States)

Taal, Elisabeth (Liesbeth) M.; Vermetten, Eric; van Schaik, Digna (Anneke) J. F.; Leenstra, Tjalling

2014-01-01

Background Military deployment to combat zones puts military personnel to a number of physical and mental challenges that may adversely affect mental health. Until now, few studies have been performed in Europe on mental health utilization after military deployment. Objective We compared the incidence of mental health consultations with the Military Mental Health Service (MMHS) of military deployed to Afghanistan to that of non-deployed military personnel. Method We assessed utilization of the MMHS by the full cohort of the Netherlands Armed Forces enlisted between 2008 and 2010 through linkage of mental health and human resource information systems. Results The total population consisted of 50,508 military (18,233 deployed, 32,275 non-deployed), who accounted for 1,906 new consultations with the MMHS. The follow-up was limited to the first 2 years following deployment. We observed higher mental health care utilization in deployed vs. non-deployed military personnel; hazard ratio (HR), adjusted for sex, military branch and time in service, 1.84 [95% CI 1.61–2.11] in the first and 1.28 [1.09–1.49] in the second year after deployment. An increased risk of adjustment disorders (HR 2.59 [2.02–3.32] and 1.74 [1.30–2.32]) and of anxiety disorders (2.22 [1.52–3.25] and 2.28 [1.50–3.45]) including posttraumatic stress disorder (5.15 [2.55–10.40] and 5.28 [2.42–11.50]), but not of mood disorders (1.33 [0.90–1.97] and 1.11 [0.68–1.82]), was observed in deployed personnel in the first- and second-year post-deployment, respectively. Military personnel deployed in a unit with a higher risk of confrontation with potentially traumatic events had a higher HR (2.13 [1.84–2.47] and 1.40 [1.18–1.67]). Conclusions Though absolute risk was low, in the first and second year following deployment to Afghanistan there was an 80 and 30% higher risk for mental health problems resulting in a consultation with the Dutch MMHS compared to military never deployed to

Westinghouse Hanford Company waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

Craig, P.A.; Nichols, D.H.; Lindsey, D.W.

1991-08-01

The purpose of this plan is to establish the Westinghouse Hanford Company's Waste Minimization Program. The plan specifies activities and methods that will be employed to reduce the quantity and toxicity of waste generated at Westinghouse Hanford Company (Westinghouse Hanford). It is designed to satisfy the US Department of Energy (DOE) and other legal requirements that are discussed in Subsection C of the section. The Pollution Prevention Awareness Program is included with the Waste Minimization Program as permitted by DOE Order 5400.1 (DOE 1988a). This plan is based on the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan, which directs DOE Field Office, Richland contractors to develop and maintain a waste minimization program. This waste minimization program is an organized, comprehensive, and continual effort to systematically reduce waste generation. The Westinghouse Hanford Waste Minimization Program is designed to prevent or minimize pollutant releases to all environmental media from all aspects of Westinghouse Hanford operations and offers increased protection of public health and the environment. 14 refs., 2 figs., 1 tab

ROSMOD: A Toolsuite for Modeling, Generating, Deploying, and Managing Distributed Real-time Component-based Software using ROS

Directory of Open Access Journals (Sweden)

Pranav Srinivas Kumar

2016-09-01

Full Text Available This paper presents the Robot Operating System Model-driven development tool suite, (ROSMOD an integrated development environment for rapid prototyping component-based software for the Robot Operating System (ROS middleware. ROSMOD is well suited for the design, development and deployment of large-scale distributed applications on embedded devices. We present the various features of ROSMOD including the modeling language, the graphical user interface, code generators, and deployment infrastructure. We demonstrate the utility of this tool with a real-world case study: an Autonomous Ground Support Equipment (AGSE robot that was designed and prototyped using ROSMOD for the NASA Student Launch competition, 2014–2015.

Impact of Deployment-Related Sexual Stressors on Psychiatric Symptoms After Accounting for Predeployment Stressors: Findings From a U.S. National Guard Cohort.

Science.gov (United States)

McCallum, Ethan B; Murdoch, Maureen; Erbes, Christopher R; Arbisi, Paul; Polusny, Melissa A

2015-08-01

This study used a longitudinal research design to examine the impact of predeployment stressors and deployment-related sexual stressors on self-reported psychiatric symptoms of U.S. National Guard soldiers returning from deployments to Iraq or Afghanistan. Prior to deployment, participants completed measures of depression and posttraumatic stress symptoms, along with an inventory of predeployment stressor experiences. At 3-months postdeployment, participants (468 men, 60 women) again completed self-report measures of psychiatric symptoms, along with an inventory of sexual stressors experienced during deployment. We compared a cross-sectional model of sexual stressors' impact on psychiatric symptoms, in which only postdeployment reports were considered, to a longitudinal model in which we adjusted for participants' predeployment stressors and psychiatric symptoms. No participants reported sexual assault during deployment, though sexual harassment was common. The cross-sectional model suggested that deployment-related sexual stressors were significantly associated with postdeployment depression (R(2) = .11) and posttraumatic stress symptoms (R(2) = .10). Once predeployment factors were taken into consideration, however, sexual stressors were no longer significant. The results did not support the notion of lasting negative impact for low-level sexual stressors (e.g., sexual harassment) during deployment after predeployment stressors are accounted for. Future studies of sexual stressors should consider longitudinal designs. © 2015 International Society for Traumatic Stress Studies.

Automated economic analysis model for hazardous waste minimization

International Nuclear Information System (INIS)

Dharmavaram, S.; Mount, J.B.; Donahue, B.A.

1990-01-01

The US Army has established a policy of achieving a 50 percent reduction in hazardous waste generation by the end of 1992. To assist the Army in reaching this goal, the Environmental Division of the US Army Construction Engineering Research Laboratory (USACERL) designed the Economic Analysis Model for Hazardous Waste Minimization (EAHWM). The EAHWM was designed to allow the user to evaluate the life cycle costs for various techniques used in hazardous waste minimization and to compare them to the life cycle costs of current operating practices. The program was developed in C language on an IBM compatible PC and is consistent with other pertinent models for performing economic analyses. The potential hierarchical minimization categories used in EAHWM include source reduction, recovery and/or reuse, and treatment. Although treatment is no longer an acceptable minimization option, its use is widespread and has therefore been addressed in the model. The model allows for economic analysis for minimization of the Army's six most important hazardous waste streams. These include, solvents, paint stripping wastes, metal plating wastes, industrial waste-sludges, used oils, and batteries and battery electrolytes. The EAHWM also includes a general application which can be used to calculate and compare the life cycle costs for minimization alternatives of any waste stream, hazardous or non-hazardous. The EAHWM has been fully tested and implemented in more than 60 Army installations in the United States

Entropy Minimizing Curves with Application to Flight Path Design and Clustering

Directory of Open Access Journals (Sweden)

Stéphane Puechmorel

2016-09-01

Full Text Available Air traffic management (ATM aims at providing companies with a safe and ideally optimal aircraft trajectory planning. Air traffic controllers act on flight paths in such a way that no pair of aircraft come closer than the regulatory separation norms. With the increase of traffic, it is expected that the system will reach its limits in the near future: a paradigm change in ATM is planned with the introduction of trajectory-based operations. In this context, sets of well-separated flight paths are computed in advance, tremendously reducing the number of unsafe situations that must be dealt with by controllers. Unfortunately, automated tools used to generate such planning generally issue trajectories not complying with operational practices or even flight dynamics. In this paper, a means of producing realistic air routes from the output of an automated trajectory design tool is investigated. For that purpose, the entropy of a system of curves is first defined, and a mean of iteratively minimizing it is presented. The resulting curves form a route network that is suitable for use in a semi-automated ATM system with human in the loop. The tool introduced in this work is quite versatile and may be applied also to unsupervised classification of curves: an example is given for French traffic.

Antenna Deployment for the Localization of Partial Discharges in Open-Air Substations

Science.gov (United States)

Robles, Guillermo; Fresno, José Manuel; Sánchez-Fernández, Matilde; Martínez-Tarifa, Juan Manuel

2016-01-01

Partial discharges are ionization processes inside or on the surface of dielectrics that can unveil insulation problems in electrical equipment. The charge accumulated is released under certain environmental and voltage conditions attacking the insulation both physically and chemically. The final consequence of a continuous occurrence of these events is the breakdown of the dielectric. The electron avalanche provokes a derivative of the electric field with respect to time, creating an electromagnetic impulse that can be detected with antennas. The localization of the source helps in the identification of the piece of equipment that has to be decommissioned. This can be done by deploying antennas and calculating the time difference of arrival (TDOA) of the electromagnetic pulses. However, small errors in this parameter can lead to great displacements of the calculated position of the source. Usually, four antennas are used to find the source but the array geometry has to be correctly deployed to have minimal errors in the localization. This paper demonstrates, by an analysis based on simulation and also experimentally, that the most common layouts are not always the best options and proposes a simple antenna layout to reduce the systematic error in the TDOA calculation due to the positions of the antennas in the array. PMID:27092501

Permanent magnet design for magnetic heat pumps using total cost minimization

Science.gov (United States)

Teyber, R.; Trevizoli, P. V.; Christiaanse, T. V.; Govindappa, P.; Niknia, I.; Rowe, A.

2017-11-01

The active magnetic regenerator (AMR) is an attractive technology for efficient heat pumps and cooling systems. The costs associated with a permanent magnet for near room temperature applications are a central issue which must be solved for broad market implementation. To address this problem, we present a permanent magnet topology optimization to minimize the total cost of cooling using a thermoeconomic cost-rate balance coupled with an AMR model. A genetic algorithm identifies cost-minimizing magnet topologies. For a fixed temperature span of 15 K and 4.2 kg of gadolinium, the optimal magnet configuration provides 3.3 kW of cooling power with a second law efficiency (ηII) of 0.33 using 16.3 kg of permanent magnet material.

Supporting deployed operations: are military nurses gaining the relevant experience from MDHUs to be competent in deployed operations?

Science.gov (United States)

Beaumont, Steven P; Allan, Helen T

2014-01-01

To explore how peacetime employment of military nurses in the UK National Health Service Medical Defence Hospital Units prepares them to be competent to practise in their role on deployment. Military secondary care nurses are employed within UK National Health Service Trusts to gain clinical experience that will be relevant to their military nursing role. A two-stage grounded theory study using mixed methods: postal questionnaire survey and in-depth interviews. In stage one a postal questionnaire was distributed to all serving military nurses. Stage two involved 12 semi-structured interviews. The data from both parts of the study were analysed using grounded theory. Four categories and one core category were identified, which suggested that participants did not feel fully prepared for deployment. Their feelings of preparedness increased with deployment experience and decreased when the nature of injuries seen on deployment changed. Respondents argued that even when unprepared, they did not feel incompetent. The findings suggest that the peacetime clinical experience gained in the National Health Service did not always develop the necessary competencies to carry out roles as military nurses on deployment. This study highlights the unique role of military nurses. We discuss these findings in the light of the literature on competency and expertise. The military nurses in this study did not feel fully prepared for deployed operations. We propose a new model for how military nurses could gain relevant experience from their National Health Service placements. National Health Service clinical placements need to be reassessed regularly to ensure that they are meeting military nurses' clinical requirements. Experiences of nurses returning from deployment could be shared and used as a basis for reflection and learning within National Health Service Trusts and also inform decisions regarding the appropriateness of clinical placements for qualified military nurses. © 2012

Reintegration Difficulty of Military Couples Following Deployment

Science.gov (United States)

2016-07-01

Response rate for Wave 8 = 88% Our final sample contained 554 men and 556 women (n = 554 cross- sex couples, 1 same- sex couple). Individuals were...story in the Killeen Daily Herald (10 April 2016) http://kdhnews.com/news/local/ kids -deployments-when-a-parent-deploys-children-face- tough...years old), and (c) “Me getting sick and having to go to sick call.” (deployed Army husband, 25 years old). Sex and fidelity. Comments fell into

Haptic feedback designs in teleoperation systems for minimal invasive surgery

NARCIS (Netherlands)

Font, I.; Weiland, S.; Franken, M.; Steinbuch, M.; Rovers, A.F.

2004-01-01

One of the major shortcomings of state-of-the-art robotic systems for minimal invasive surgery is the lack of haptic feedback for the surgeon. In order to provide haptic information, sensors and actuators have to be added to the master and slave device. A control system should process the data and

Market and Policy Barriers to Energy Storage Deployment

Energy Technology Data Exchange (ETDEWEB)

Bhatnagar, Dhruv [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Currier, Aileen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hernandez, Jacquelynne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ma, Ookie [Dept. of Energy (DOE), Washington DC (United States) Office of Energy Efficiency and Renewable Energy; Kirby, Brendan [Consultant

2013-09-01

Electric energy storage technologies can provide numerous grid services; there are a number of factors that restrict their current deployment. The most significant barrier to deployment is high capital costs, though several recent deployments indicate that capital costs are decreasing and energy storage may be the preferred economic alternative in certain situations. However, a number of other market and regulatory barriers persist, limiting further deployment. These barriers can be categorized into regulatory barriers, market (economic) barriers, utility and developer business model barriers, cross-cutting barriers and technology barriers.

Environmental issues affecting clean coal technology deployment

Energy Technology Data Exchange (ETDEWEB)

Miller, M.J. [Electric Power Research Inst., Palo Alto, CA (United States)

1997-12-31

The author outlines what he considers to be the key environmental issues affecting Clean Coal Technology (CCT) deployment both in the US and internationally. Since the international issues are difficult to characterize given different environmental drivers in various countries and regions, the primary focus of his remarks is on US deployment. However, he makes some general remarks, particularly regarding the environmental issues in developing vs. developed countries and how these issues may affect CCT deployment. Further, how environment affects deployment depends on which particular type of clean coal technology one is addressing. It is not the author`s intention to mention many specific technologies other than to use them for the purposes of example. He generally categorizes CCTs into four groups since environment is likely to affect deployment for each category somewhat differently. These four categories are: Precombustion technologies such as coal cleaning; Combustion technologies such as low NOx burners; Postcombustion technologies such as FGD systems and postcombustion NOx control; and New generation technologies such as gasification and fluidized bed combustion.

Decision Optimization of Machine Sets Taking Into Consideration Logical Tree Minimization of Design Guidelines

Science.gov (United States)

Deptuła, A.; Partyka, M. A.

2014-08-01

The method of minimization of complex partial multi-valued logical functions determines the degree of importance of construction and exploitation parameters playing the role of logical decision variables. Logical functions are taken into consideration in the issues of modelling machine sets. In multi-valued logical functions with weighting products, it is possible to use a modified Quine - McCluskey algorithm of multi-valued functions minimization. Taking into account weighting coefficients in the logical tree minimization reflects a physical model of the object being analysed much better

Prediction, Expectation, and Surprise: Methods, Designs, and Study of a Deployed Traffic Forecasting Service

OpenAIRE

Horvitz, Eric J.; Apacible, Johnson; Sarin, Raman; Liao, Lin

2012-01-01

We present research on developing models that forecast traffic flow and congestion in the Greater Seattle area. The research has led to the deployment of a service named JamBayes, that is being actively used by over 2,500 users via smartphones and desktop versions of the system. We review the modeling effort and describe experiments probing the predictive accuracy of the models. Finally, we present research on building models that can identify current and future surprises, via efforts on mode...

FloorNet: Deployment and Evaluation of a Multihop Wireless 802.11 Testbed

Directory of Open Access Journals (Sweden)

Zink Michael

2010-01-01

Full Text Available A lot of attention has been given to multihop wireless networks lately, but further research—in particular, through experimentation—is needed. This attention has motivated an increase in the number of 802.11-based deployments, both indoor and outdoor. These testbeds, which require a significant amount of resources during both deployment and maintenance, are used to run measurements in order to analyze and understand the limitation and differences between analytical or simulation-based figures and the results from real-life experimentation. This paper makes two major contributions: (i first, we describe a novel wireless multihop testbed, which we name FloorNet, that is deployed and operated under the false floor of a lab in our Computer Science building. This false floor provides a strong physical protection that prevents disconnections or misplacements, as well as radio shielding (to some extent thanks to the false floor panels—this later feature is assessed through experimentation; (ii second, by running exhaustive and controlled experiments we are able to analyze the performance limits of commercial off-the-shelf hardware, as well as to derive practical design criteria for the deployment and configuration of mesh networks. These results both provide valuable insights of wireless multihop performance and prove that FloorNet constitutes a valuable asset to research on wireless mesh networks.

Coming home: A prospective study of family reintegration following deployment to a war zone.

Science.gov (United States)

Balderrama-Durbin, Christina; Cigrang, Jeffrey A; Osborne, Laura J; Snyder, Douglas K; Talcott, G Wayne; Slep, Amy M Smith; Heyman, Richard E; Tatum, JoLyn; Baker, Monty; Cassidy, Daniel; Sonnek, Scott

2015-08-01

The consequences of deployment extend beyond the service member to impact the entire family. The current investigation evaluated the unique challenges of family reintegration for partnered service members using a prospective design. In total, 76 partnered service members who deployed on a year-long, high-risk mission to Iraq were assessed across the entirety of the deployment cycle, i.e., pre-, during, and postdeployment. At follow-up, nearly 1 in 5 partnered service members reported moderate to severe difficulties in multiple aspects of family reintegration. Prospective interpersonal indicators such as preparations for deployment as a couple, shared commitment to the military, and predeployment relationship distress predicted postdeployment family reintegration difficulties. Significant interpersonal risk factors were medium to large in their effect sizes. Airmen's willingness to disclose deployment- and combat-related experiences, and postdeployment relationship distress served as concurrent interpersonal correlates of difficulties with family reintegration. Intrapersonal factors, including posttraumatic stress symptoms and alcohol misuse were concurrently related to challenges with family reintegration; predeployment alcohol misuse also predicted subsequent family reintegration difficulties. Additional analyses indicated that pre- and postdeployment relationship distress, combat disclosure, and postdeployment alcohol misuse each contributed to family reintegration when controlling for other intra- and interpersonal risk factors. Implications for prevention and early intervention strategies as well as future research are discussed. (c) 2015 APA, all rights reserved).

Advances in Automated Plankton Imaging: Enhanced Throughput, Automated Staining, and Extended Deployment Modes for Imaging FlowCytobot

Science.gov (United States)

Sosik, H. M.; Olson, R. J.; Brownlee, E.; Brosnahan, M.; Crockford, E. T.; Peacock, E.; Shalapyonok, A.

2016-12-01

Imaging FlowCytobot (IFCB) was developed to fill a need for automated identification and monitoring of nano- and microplankton, especially phytoplankton in the size range 10 200 micrometer, which are important in coastal blooms (including harmful algal blooms). IFCB uses a combination of flow cytometric and video technology to capture high resolution (1 micrometer) images of suspended particles. This proven, now commercially available, submersible instrument technology has been deployed in fixed time series locations for extended periods (months to years) and in shipboard laboratories where underway water is automatically analyzed during surveys. Building from these successes, we have now constructed and evaluated three new prototype IFCB designs that extend measurement and deployment capabilities. To improve cell counting statistics without degrading image quality, a high throughput version (IFCB-HT) incorporates in-flow acoustic focusing to non-disruptively pre-concentrate cells before the measurement area of the flow cell. To extend imaging to all heterotrophic cells (even those that do not exhibit chlorophyll fluorescence), Staining IFCB (IFCB-S) incorporates automated addition of a live-cell fluorescent stain (fluorescein diacetate) to samples before analysis. A horizontally-oriented IFCB-AV design addresses the need for spatial surveying from surface autonomous vehicles, including design features that reliably eliminate air bubbles and mitigate wave motion impacts. Laboratory evaluation and test deployments in waters near Woods Hole show the efficacy of each of these enhanced IFCB designs.

Theories of minimalism in architecture: Post scriptum

Directory of Open Access Journals (Sweden)

Stevanović Vladimir

2012-01-01

Full Text Available Owing to the period of intensive development in the last decade of XX century, architectural phenomenon called Minimalism in Architecture was remembered as the Style of the Nineties, which is characterized, morphologically speaking, by simplicity and formal reduction. Simultaneously with its development in practice, on a theoretical level several dominant interpretative models were able to establish themselves. The new millennium and time distance bring new problems; therefore this paper represents a discussion on specific theorization related to Minimalism in Architecture that can bear the designation of post scriptum, because their development starts after the constitutional period of architectural minimalist discourse. In XXI century theories, the problem of definition of minimalism remains important topic, approached by theorists through resolving on the axis: Modernism - Minimal Art - Postmodernism - Minimalism in Architecture. With regard to this, analyzed texts can be categorized in two groups: 1 texts of affirmative nature and historical-associative approach in which minimalism is identified with anything that is simple and reduced, in an idealizing manner, relied mostly on the existing hypotheses; 2 critically oriented texts, in which authors reconsider adequacy of the very term 'minimalism' in the context of architecture and take a metacritical attitude towards previous texts.

Minimal changes in health status questionnaires: distinction between minimally detectable change and minimally important change

Directory of Open Access Journals (Sweden)

Knol Dirk L

2006-08-01

Full Text Available Abstract Changes in scores on health status questionnaires are difficult to interpret. Several methods to determine minimally important changes (MICs have been proposed which can broadly be divided in distribution-based and anchor-based methods. Comparisons of these methods have led to insight into essential differences between these approaches. Some authors have tried to come to a uniform measure for the MIC, such as 0.5 standard deviation and the value of one standard error of measurement (SEM. Others have emphasized the diversity of MIC values, depending on the type of anchor, the definition of minimal importance on the anchor, and characteristics of the disease under study. A closer look makes clear that some distribution-based methods have been merely focused on minimally detectable changes. For assessing minimally important changes, anchor-based methods are preferred, as they include a definition of what is minimally important. Acknowledging the distinction between minimally detectable and minimally important changes is useful, not only to avoid confusion among MIC methods, but also to gain information on two important benchmarks on the scale of a health status measurement instrument. Appreciating the distinction, it becomes possible to judge whether the minimally detectable change of a measurement instrument is sufficiently small to detect minimally important changes.

Brazing retort manifold design concept may minimize air contamination and enhance uniform gas flow

Science.gov (United States)

Ruppe, E. P.

1966-01-01

Brazing retort manifold minimizes air contamination, prevents gas entrapment during purging, and provides uniform gas flow into the retort bell. The manifold is easily cleaned and turbulence within the bell is minimized because all manifold construction lies outside the main enclosure.

Testing Starshade Manufacturing and Deployment Through NASA's Technology Development for Exoplanet Missions Program

Science.gov (United States)

Kasdin, N. J.; Shaklan, S.; Lisman, D.; Thomson, M.; Cady, E.; Lo, A.; Macintosh, B.

2014-01-01

An external occulter is a satellite employing a large screen, or starshade, that flies in formation with a spaceborne telescope to provide the starlight suppression needed for detecting and characterizing exoplanets. Among the advantages of using an occulter are the broadband allowed for characterization and the removal of light before entering the observatory, greatly relaxing the requirements on the telescope and instrument. In this poster we report on the results of our two Technology Development for Exoplanet Missions (TDEM) studies. In the first we examined the manufacturability and metrology of starshade petals, successfully constructing a full size petal from flight like materials and showing through precise edge shape measurements that an occulter made with petals consistent with the measured accuracy would achieve close to 10^-10 contrast. Our second TDEM tested the deployment precision of a roughly half-scale starshade. We demonstrated the deployment of an existing deployable truss outfitted with four sub-scale petals and a custom designed central hub. We showed that the system can be deployed multiple times with a repeatable positioning accuracy of the petals better than the requirement of 1.0 mm. The combined results of these two TDEM projects has significantly advanced the readiness level of occulter technology and moved the community closer to a realizable mission.

Review of deployment technology for tethered satellite systems

Science.gov (United States)

Yu, B. S.; Wen, H.; Jin, D. P.

2018-03-01

Tethered satellite systems (TSSs) have attracted significant attention due to their potential and valuable applications for scientific research. With the development of various launched on-orbit missions, the deployment of tethers is considered a crucial technology for operation of a TSS. Both past orbiting experiments and numerical results have shown that oscillations of the deployed tether due to the Coriolis force and environmental perturbations are inevitable and that the impact between the space tether and end-body at the end of the deployment process leads to complicated nonlinear phenomena. Hence, a set of suitable control methods plays a fundamental role in tether deployment. This review article summarizes previous work on aspects of the dynamics, control, and ground-based experiments of tether deployment. The relevant basic principles, analytical expressions, simulation cases, and experimental results are presented as well.

Suggestion of Design Evaluation Plan based on Star Life Cycle to introduce the Information Minimalism Concept of KOREA Nuclear Plant

Science.gov (United States)

Jang, Gwi-sook; Lee, Seung-min; Park, Gee-yong

2018-01-01

The design of Korea Nuclear Power Plant (NPP) main control rooms (MCR) has been changed to be fully digitalized. Five or six display devices are assigned to each operator in NPP MCR to provide the information of safety parameter and plant status, and various control functions by connecting computerized control devices. Under this circumstance, the distributed displays can induce a dispersion of the operators' attention and increase the workload while conducting monitoring and control tasks efficiently. In addition, to support human operators to reduce their workload and increase the performance, the concepts of the ecological interface design (EID) and the operator-centered design were applied to the design HMI display. However these designs are applied to a limited set of screens and did not differ largely from the traditional HMI design in that the layout of the information is somewhere similar to P&IDs. In this paper, we propose a design evaluation plan based on star life cycle to introduce the information minimalism concept for designing an HMI display.

Influence of military component and deployment-related experiences on mental disorders among Canadian military personnel who deployed to Afghanistan: a cross-sectional survey

Science.gov (United States)

Boulos, David; Fikretoglu, Deniz

2018-01-01

Objective The primary objective was to explore differences in mental health problems (MHP) between serving Canadian Armed Forces (CAF) components (Regular Force (RegF); Reserve Force (ResF)) with an Afghanistan deployment and to assess the contribution of both component and deployment experiences to MHP using covariate-adjusted prevalence difference estimates. Additionally, mental health services use (MHSU) was descriptively assessed among those with a mental disorder. Design Data came from the 2013 CAF Mental Health Survey, a cross-sectional survey of serving personnel (n=72 629). Analyses were limited to those with an Afghanistan deployment (population n=35 311; sampled n=4854). Logistic regression compared MHP between RegF and ResF members. Covariate-adjusted prevalence differences were computed. Primary outcome measure The primary outcomes were MHP, past-year mental disorders, identified using the WHO’s Composite International Diagnostic Interview, and past-year suicide ideation. Results ResF personnel were less likely to be identified with a past-year anxiety disorder (adjusted OR (AOR)=0.72 (95% CI 0.58 to 0.90)), specifically both generalised anxiety disorder and panic disorder, but more likely to be identified with a past-year alcohol abuse disorder (AOR=1.63 (95% CI 1.04 to 2.58)). The magnitude of the covariate-adjusted disorder prevalence differences for component was highest for the any anxiety disorder outcome, 2.8% (95% CI 1.0 to 4.6); lower for ResF. All but one deployment-related experience variable had some association with MHP. The ‘ever felt responsible for the death of a Canadian or ally personnel’ experience had the strongest association with MHP; its estimated covariate-adjusted disorder prevalence difference was highest for the any (of the six measured) mental disorder outcome (11.2% (95% CI 6.6 to 15.9)). Additionally, ResF reported less past-year MHSU and more past-year civilian MHSU. Conclusions Past-year MHP differences were

Concurrent engineering: effective deployment strategies

Directory of Open Access Journals (Sweden)

Unny Menon

1996-12-01

Full Text Available This paper provides a comprehensive insight into current trends and developments in Concurrent Engineering for integrated development of products and processes with the goal of completing the entire cycle in a shorter time, at lower overall cost and with fewer engineering design changes after product release. The evolution and definition of Concurrent Engineering are addressed first, followed by a concise review of the following elements of the concurrent engineering approach to product development: Concept Development: The Front-End Process, identifying Customer Needs and Quality Function Deployment, Establishing Product Specifications, Concept Selection, Product Architecture, Design for Manufacturing, Effective Rapid Prototyping, and The Economics of Product Development. An outline of a computer-based tutorial developed by the authors and other graduate students funded by NASA ( accessible via the world-wide-web . is provided in this paper. A brief discussion of teamwork for successful concurrent engineering is included, t'ase histories of concurrent engineering implementation at North American and European companies are outlined with references to textbooks authored by Professor Menon and other writers. A comprehensive bibliography on concurrent engineering is included in the paper.

Differential Child Maltreatment Risk Across Deployment Periods of US Army Soldiers.

Science.gov (United States)

Taylor, Christine M; Ross, Michelle E; Wood, Joanne N; Griffis, Heather M; Harb, Gerlinde C; Mi, Lanyu; Song, Lihai; Strane, Douglas; Lynch, Kevin G; Rubin, David M

2016-01-01

We described the risk for maltreatment among toddlers of US Army soldiers over different deployment cycles to develop a systematic response within the US Army to provide families appropriate supports. We conducted a person-time analysis of substantiated maltreatment reports and medical diagnoses among children of 112,325 deployed US Army soldiers between 2001 and 2007. Risk of maltreatment was elevated after deployment for children of soldiers deployed once but not for children of soldiers deployed twice. During the 6 months after deployment, children of soldiers deployed once had 4.43 substantiated maltreatment reports and 4.96 medical diagnoses per 10,000 child-months. The highest maltreatment rate among children of soldiers deployed twice occurred during the second deployment for substantiated maltreatment (4.83 episodes per 10,000 child-months) and before the first deployment for medical diagnoses of maltreatment (3.78 episodes per 10,000 child-months). We confirmed an elevated risk for child maltreatment during deployment but also found a previously unidentified high-risk period during the 6 months following deployment, indicating elevated stress within families of deployed and returning soldiers. These findings can inform efforts by the military to initiate and standardize support and preparation to families during periods of elevated risk.

Miniaturized robotically deployed sensor systems for in-situ characterization of hazardous waste

International Nuclear Information System (INIS)

Fischer, G.J.

1996-01-01

A series of ''MiniLab'' end effectors are currently being designed for robotic deployment in hazardous areas such as waste storage tanks at Idaho National Engineering Laboratories (INEL) and Oak Ridge National Laboratory (ORNL). These MiniLabs will be the first ever multichannel hazardous waste characterization end effectors deployed in underground high level waste storage tanks. They consist of a suite of chemical, radiological, and physical properties sensors integrated into a compact package mounted on the end of a robotic arm and/or vehicle. Most of the sensors are commercially available thus reducing the overall cost of design and maintenance. Sensor configurations can be customized depending on site/customer needs. This paper will address issues regarding the cost of field sampling verses MiniLab in-situ measurements and a brief background of the Light Duty utility Arm (LDUA) program. Topics receiving in depth attention will include package size parameters/constraints, design specifications, and investigations of currently available sensor technology. Sensors include radiological, gas, chemical, electrolytic, visual, temperature, and ranging. The effects of radiation on the life of the systems/sensors will also be discussed. Signal processing, control, display, and data acquisition methods will be described. The paper will conclude with an examination of possible applications for MiniLabs

Waste minimization - Hanford's strategy for sustainability

International Nuclear Information System (INIS)

Merry, D.S.

1998-01-01

The Hanford Site cleanup activity is an immense and challenging undertaking, which includes characterization and decommissioning of 149 single-shell storage tanks, treating waste stored in 28 double-shell tanks, safely disposing of over 2,100 metric tons of spent nuclear fuel stored onsite, removing thousands of structures, and dealing with significant solid waste, groundwater, and land restoration issues. The Pollution Prevention/Waste Minimization (P2/WMin) Program supports the Hanford Site mission to safely clean up and manage legacy waste and to develop and deploy science and technology in many ways. Once such way is through implementing and documenting over 231 waste reduction projects during the past five years, resulting in over $93 million in cost savings/avoidances. These savings/avoidances allowed other high priority cleanup work to be performed. Another way is by exceeding the Secretary of Energy's waste reduction goals over two years ahead of schedule, thus reducing the amount of waste to be stored, treated and disposed. Six key elements are the foundation for these sustained P2/WMin results

Design, Certification, and Deployment of the Colorimetric Water Quality Monitoring Kit (CWQMK)

Science.gov (United States)

Gazda, Daniel B.; Nolan, Daniel J.; Rutz, Jeff A.; Schultz, John R.; Siperko, Lorraine M.; Porter, Marc D.; Lipert, Robert J.; Flint, Stephanie M.; McCoy, J. Torin

2010-01-01

In August 2009, an experimental water quality monitoring kit based on Colorimetric Solid Phase Extraction (CSPE) technology was delivered to the International Space Station (ISS) aboard STS-128/17A. The kit, called the Colorimetric Water Quality Monitoring Kit (CWQMK), was flown and deployed as a Station Development Test Objective (SDTO) experiment on the ISS. The goal of the SDTO experiment is to evaluate the acceptability of CSPE technology for routine water quality monitoring on the ISS. This paper provides an overview of the SDTO experiment, as well as a detailed description of the CWQMK hardware and a summary of the testing and analysis conducted to certify the CWQMK for use on the ISS. The initial results obtained from the SDTO experiment are also reported and discussed in detail

Minimal hardware Bluetooth tracking for long-term at-home elder supervision.

Science.gov (United States)

Kelly, Damian; McLoone, Sean; Farrell, Ronan

2010-01-01

The ability to automatically detect the location of an elder within their own home is a significant enabler of remote elder supervision and interaction applications. This location information is typically generated via a myriad of sensors throughout the home environment. Even with high sensor redundancy, there are still situations where traditional elder monitoring systems are unable to resolve the location of the elder. This work develops a minimal infrastructure radio-frequency localisation system for long-term elder location tracking. An RFID room-labelling technique is employed and with it, the localisation system developed in this work is shown to exhibit superior performance to more traditional localisation systems in realistic long-term deployments.

Minimally inconsistent reasoning in Semantic Web.

Science.gov (United States)

Zhang, Xiaowang

2017-01-01

Reasoning with inconsistencies is an important issue for Semantic Web as imperfect information is unavoidable in real applications. For this, different paraconsistent approaches, due to their capacity to draw as nontrivial conclusions by tolerating inconsistencies, have been proposed to reason with inconsistent description logic knowledge bases. However, existing paraconsistent approaches are often criticized for being too skeptical. To this end, this paper presents a non-monotonic paraconsistent version of description logic reasoning, called minimally inconsistent reasoning, where inconsistencies tolerated in the reasoning are minimized so that more reasonable conclusions can be inferred. Some desirable properties are studied, which shows that the new semantics inherits advantages of both non-monotonic reasoning and paraconsistent reasoning. A complete and sound tableau-based algorithm, called multi-valued tableaux, is developed to capture the minimally inconsistent reasoning. In fact, the tableaux algorithm is designed, as a framework for multi-valued DL, to allow for different underlying paraconsistent semantics, with the mere difference in the clash conditions. Finally, the complexity of minimally inconsistent description logic reasoning is shown on the same level as the (classical) description logic reasoning.

Clean energy deployment: addressing financing cost

International Nuclear Information System (INIS)

Ameli, Nadia; Kammen, Daniel M

2012-01-01

New methods are needed to accelerate clean energy policy adoption. To that end, this study proposes an innovative financing scheme for renewable and energy efficiency deployment. Financing barriers represent a notable obstacle for energy improvements and this is particularly the case for low income households. Implementing a policy such as PACE—property assessed clean energy—allows for the provision of upfront funds for residential property owners to install electric and thermal solar systems and make energy efficiency improvements to their buildings. This paper will inform the design of better policies tailored to the creation of the appropriate conditions for such investments to occur, especially in those countries where most of the population belongs to the low–middle income range facing financial constraints. (letter)

Clean energy deployment: addressing financing cost

Science.gov (United States)

Ameli, Nadia; Kammen, Daniel M.

2012-09-01

New methods are needed to accelerate clean energy policy adoption. To that end, this study proposes an innovative financing scheme for renewable and energy efficiency deployment. Financing barriers represent a notable obstacle for energy improvements and this is particularly the case for low income households. Implementing a policy such as PACE—property assessed clean energy—allows for the provision of upfront funds for residential property owners to install electric and thermal solar systems and make energy efficiency improvements to their buildings. This paper will inform the design of better policies tailored to the creation of the appropriate conditions for such investments to occur, especially in those countries where most of the population belongs to the low-middle income range facing financial constraints.

Psychiatric Effects of Military Deployment on Children and Families

Science.gov (United States)

James, Trenton

2012-01-01

Deployments in the United States military have increased greatly in the past 10 years. Families and children are psychiatrically affected by these deployments, and recent studies are clarifying these effects. This article focuses on the psychiatric effects of deployment on children and uses a composite case example to review the use of play therapy to treat children who are having psychiatric issues related to the deployment of one or both parents. PMID:22468239

Applying Quality Function Deployment in Industrial Design Curriculum Planning

Science.gov (United States)

Liu, Shuo-Fang; Lee, Yann-Long; Lin, Yi-Zhi; Tseng, Chien-Feng

2013-01-01

Industrial design is a discipline that combines multiple professional fields. Enterprise demands for industrial design competencies also change over time; thus, the curriculum of industrial design education should be compatible with the current demands of the industry. However, scientific approaches have not been previously employed to plan…

Responsiveness and minimal clinically important change

DEFF Research Database (Denmark)

Christiansen, David Høyrup; Frost, Poul; Falla, Deborah

2015-01-01

Study Design A prospective cohort study nested in a randomized controlled trial. Objectives To determine and compare responsiveness and minimal clinically important change of the modified Constant score (CS) and the Oxford Shoulder Score (OSS). Background The OSS and the CS are commonly used...... to assess shoulder outcomes. However, few studies have evaluated the measurement properties of the OSS and CS in terms of responsiveness and minimal clinically important change. Methods The study included 126 patients who reported having difficulty returning to usual activities 8 to 12 weeks after...... were observed for the CS and the OSS. Minimal clinically important change ROC values were 6 points for the OSS and 11 points for the CS, with upper 95% cutoff limits of 12 and 22 points, respectively. Conclusion The CS and the OSS were both suitable for assessing improvement after decompression surgery....

Recommendations to designers aimed at minimizing radiation dose incurred in operation, maintenance, inspection and repair of light-water reactors

International Nuclear Information System (INIS)

1978-01-01

In the framework of the exchange of experience between nuclear power plant operators organized by the services of the Commission of the European Communities an ad-hoc working party elaborated recommendations particularly directed to those concerned with design of light water reactor plants. The necessary design measures which should be followed to minimize radiation dose incurred in operation, maintenance, inspection and repair of such reactors are listed. The recommendations are based on recent views expressed by operating utilities within the Community. It is intended to revise these recommendations at suitable intervals in order to make use of the most recent experience and to keep the report up to date with the actual state of art in nuclear technology

Evolved Minimal Frustration in Multifunctional Biomolecules.

Science.gov (United States)

Röder, Konstantin; Wales, David J

2018-05-25

Protein folding is often viewed in terms of a funnelled potential or free energy landscape. A variety of experiments now indicate the existence of multifunnel landscapes, associated with multifunctional biomolecules. Here, we present evidence that these systems have evolved to exhibit the minimal number of funnels required to fulfil their cellular functions, suggesting an extension to the principle of minimum frustration. We find that minimal disruptive mutations result in additional funnels, and the associated structural ensembles become more diverse. The same trends are observed in an atomic cluster. These observations suggest guidelines for rational design of engineered multifunctional biomolecules.

MENCIPTAKAN KEPUASAN TOTAL PELANGGAN MELALUI PENGGUNAAN QUALITY FUNCTION DEPLOYMENT PADA AGRIBISNIS SAYURAN [Creating Total Customer Satisfaction by Using Quality Function Deployment in Vegetables Agribusiness

Directory of Open Access Journals (Sweden)

Abidin 1

2001-08-01

Full Text Available In the product design and development processes, Quality Function Deployment (QFD provides a comprehensive, systematic approach to ensure that the products meet or exceed customer expectations. This paper reports the results of vegetables customers survey in Jakarta. Analytical Hierarchy Process (AHP method was used for weighing the result of survey, and the customer expectation were translated using QFD. To meet the biggest customer expectation, i.e. vegetables freshness, Just In Time (JIT concept was utilized.

Garden State Parkway Corridor : ITS early deployment planning study : strategic deployment plan

Science.gov (United States)

1997-12-01

This Strategic Deployment Plan describes ways of improving travel within the Garden : State Parkway Corridor using intelligent transportation systems (ITS) and without : constructing additional roadway lanes. Travel improvements will be possible with...

Minimal-Inversion Feedforward-And-Feedback Control System

Science.gov (United States)

Seraji, Homayoun

1990-01-01

Recent developments in theory of control systems support concept of minimal-inversion feedforward-and feedback control system consisting of three independently designable control subsystems. Applicable to the control of linear, time-invariant plant.

Aplikasi Ergonomic Function Deployment (Efd Pada Redesign Alat Parut Kelapa Untuk Ibu Rumah Tangga

Directory of Open Access Journals (Sweden)

Roberta Zulfhi Surya

2015-04-01

Ergonomic Function Deployment (Efd Application In Coconut Grater Redesign For HousewifeAbstract. Pulverizing (coconut grated is one of daily kitchen worksconducted by housewives. A common existing coconut grater which is available on the market is normally works using a crank system. Housewives have complaints of pain in the limbs, especially the hands, waist and back after using this grater. This study aims to improve the design of coconut grater with Ergonomic Function Deployment (EFD based system and determine the housewife musculoskeletal decline as users. Further, to examine pulverizing time difference after redesign. The study was conducted at RT. 001 RW. 005 West Tembilahan Hulu village, subdistrict Tembilahan Indragiri Hilir. The method use in this study is same design subject (treatment by subjects design with co added Colton equation. Atotal of 12 housewives were used and subjected to the calculation. A grater redesign with EFD system was obtained by creating House of Ergonomic (HOE matrices and determining the anthropometric data. Whilst musculoskeletal disorders were obtained by generating Nordic Body Map (NBMworksheets questionnaire. Moreover, pulverizing time was obtained by testing coconut graterused before and after redesign. Results of the study showed that the redesign tool based on Ergonomic Function Deployment (EFD systemwasfound to be more convenient form which five ergonomics aspects required was fulfilled: effective, convenient, safe, healthy, and efficient (ENASE. Housewife musculoskeletal complaints decreased by 0.285% or 17.39%. This study also shows that coconut pulverizing time is 5 minutes faster and increased by 30.10% after redesigning the coconut grater crank system.

Minimal surfaces

CERN Document Server

Dierkes, Ulrich; Sauvigny, Friedrich; Jakob, Ruben; Kuster, Albrecht

2010-01-01

Minimal Surfaces is the first volume of a three volume treatise on minimal surfaces (Grundlehren Nr. 339-341). Each volume can be read and studied independently of the others. The central theme is boundary value problems for minimal surfaces. The treatise is a substantially revised and extended version of the monograph Minimal Surfaces I, II (Grundlehren Nr. 295 & 296). The first volume begins with an exposition of basic ideas of the theory of surfaces in three-dimensional Euclidean space, followed by an introduction of minimal surfaces as stationary points of area, or equivalently

Deployment Instabilities of Lobed-Pumpkin Balloon

Science.gov (United States)

Nakashino, Kyoichi

A lobed-pumpkin balloon, currently being developed in ISAS/JAXA as well as in NASA, is a promising vehicle for long duration scientific observations in the stratosphere. Recent ground and flight experiments, however, have revealed that the balloon has deployment instabilities under certain conditions. In order to overcome the instability problems, a next generation SPB called 'tawara' type balloon has been proposed, in which an additional cylindrical part is appended to the standard lobed-pumpkin balloon. The present study investigates the deployment stability of tawara type SPB in comparison to that of standard lobed-pumpkin SPB through eigenvalue analysis on the basis of finite element methods. Our numerical results show that tawara type SPB enjoys excellent deployment performance over the standard lobed-pumpkin SPBs.

Large Deployable Reflector (LDR)

Science.gov (United States)

Alff, W. H.

1980-01-01

The feasibility and costs were determined for a 1 m to 30 m diameter ambient temperature, infrared to submillimeter orbiting astronomical telescope which is to be shuttle-deployed, free-flying, and have a 10 year orbital life. Baseline concepts, constraints on delivery and deployment, and the sunshield required are examined. Reflector concepts, the optical configuration, alignment and pointing, and materials are also discussed. Technology studies show that a 10 m to 30 m diameter system which is background and diffraction limited at 30 micron m is feasible within the stated time frame. A 10 m system is feasible with current mirror technology, while a 30 m system requires technology still in development.

Designing Products Using Quality Function Deployment and Conjoint Analysis: A Comparison in a Market for Elderly People

Science.gov (United States)

Abu-Assab, Samah; Baier, Daniel

In this paper, we compare two product design approaches, quality function deployment (QFD) and conjoint analysis (CA), on the example of mobile phones for elderly people as a target group. Then, we compare between our results and the results from former similar comparisons, e.g., Pullman et al. (J Prod Innov Manage 19(5):354-364, 2002) and Katz (J Innov Manage 21:61-63, 2004). In this work, the same procedures and conditions are taken into consideration as that taken by Pullman et al. in their paper. They viewed the relation between the two methods: QFD and CA as a complementary one in which both should be simultaneously implemented since each provide feedback to the other. They concluded that CA is more efficient in reflecting the end-users’ present preferences for the product attributes, whereas QFD is definitely better in satisfying end-users’ needs from the developers’ point of view. Katz in his response from a practitioner’s point of view agreed with Pullman et al. However, he concluded that the two methods are better used sequentially and that QFD should precede conjoint analysis. We test these results in a market for elderly people.

Semi-portable whole body counter deployable during post-radiological accident

International Nuclear Information System (INIS)

Panchal, C.G.; Bansode, P.Y.; Vinod, M.; Sarade, Bhagyashree; Jain, R.K.; Jakati, R.K.; Pithawa, C.K.

2012-01-01

A versatile whole body counter with the state of art electronics has been indigenously designed and developed which can be readily deployed for use during nuclear emergency. This instrument is designed to quickly identify and quantify the activity of high energy photon emitters accumulated particularly in vital organs like thyroid, lungs besides the body of the victims of the radiological incident or accident. Special features of the instruments are swivel type detectors assembly mountable on a wall or table top and detachable collimator configurable to assess the internal contamination selectively to meet protective measures of the radiological accidents, mechanically rugged and functionally reliable to perform in contaminated environmental field conditions. (author)

Cooperative Technolgy Deployed

NARCIS (Netherlands)

Koenders, E.; Velt, R. in 't

2011-01-01

After the successful demonstrations of cooperative technology by the CVIS and Safespot projects the question remains how this technology can be successfully deployed. This question is explored by the Field Operational Test project FREILOT, which aims to provide fuel economy applications that must be

Center for Deployment Psychology

Data.gov (United States)

Federal Laboratory Consortium — The Center for Deployment Psychology was developed to promote the education of psychologists and other behavioral health specialists about issues pertaining to the...

Finding Their Way Back In: Family Reintegration Following Guard Deployment.

Science.gov (United States)

Messecar, Deborah C

2017-03-01

The aim of this study was to describe deployed National Guard members' and their families' perceptions of their experience with family reintegration, and the causes and conditions of challenges reintegration presents after deployment. A total of 26 National Guard members and 19 family members participated in individual (n = 22), couples (n = 6), or focus group (n = 17) interviews. In-depth interviews were used to assess needs and maximize input from military families regarding deployment-related experiences and reintegration issues. Qualitative coding and analysis of data were completed using NVivo. Finding their way back in is the key process that the military members must complete to successfully reestablish their desired social connections with the family and reclaim their place within the family. Several conditions shape the degree of challenges with reintegration that veterans and their family will encounter. These include preparation for deployment, length and type of deployment, communication during deployment, and finally, awareness of how deployment changes the military member and the family. Support resources dedicated to providing National Guard members and their families with assistance in preparing for deployments and educating them about the importance of communication during deployment should be maintained and expanded. Broader educational efforts that increase awareness of what to expect regarding how deployment changes the military member and the family are needed. Reprint & Copyright © 2017 Association of Military Surgeons of the U.S.

The DevOps 2.0 toolkit automating the continuous deployment pipeline with containerized microservices

CERN Document Server

Farcic, Viktor

2016-01-01

This book is about different techniques that help us architect software in a better and more efficient way with microservices packed as immutable containers, tested and deployed continuously to servers that are automatically provisioned with configuration management tools. It's about fast, reliable and continuous deployments with zero-downtime and ability to roll-back. It's about scaling to any number of servers, design of self-healing systems capable of recuperation from both hardware and software failures and about centralized logging and monitoring of the cluster.In other words, this book envelops the whole microservices development and deployment lifecycle using some of the latest and greatest practices and tools. We'll use Docker, Kubernetes, Ansible, Ubuntu, Docker Swarm and Docker Compose, Consul, etcd, Registrator, confd, and so on. We'll go through many practices and even more tools. Finally, while there will be a lot of theory, this is a hands-on book. You won't be able to complete it by reading it ...

Small cell networks deployment, management, and optimization

CERN Document Server

Claussen, Holger; Ho, Lester; Razavi, Rouzbeh; Kucera, Stepan

2018-01-01

Small Cell Networks: Deployment, Management, and Optimization addresses key problems of the cellular network evolution towards HetNets. It focuses on the latest developments in heterogeneous and small cell networks, as well as their deployment, operation, and maintenance. It also covers the full spectrum of the topic, from academic, research, and business to the practice of HetNets in a coherent manner. Additionally, it provides complete and practical guidelines to vendors and operators interested in deploying small cells. The first comprehensive book written by well-known researchers and engineers from Nokia Bell Labs, Small Cell Networks begins with an introduction to the subject--offering chapters on capacity scaling and key requirements of future networks. It then moves on to sections on coverage and capacity optimization, and interference management. From there, the book covers mobility management, energy efficiency, and small cell deployment, ending with a section devoted to future trends and applicat...

RSOI: Force Deployment Bottleneck

National Research Council Canada - National Science Library

D'Amato, Mark

1998-01-01

This study uses The Theory Of Constraints (TOC) management methodology and recent military missions to show that RSOI operations are generally the limiting constraint to force deployment operations...

An assessment of surface mud system design options for minimizing the health, safety, and environmental impact concerns associated with drilling fluids

International Nuclear Information System (INIS)

Minton, R.C.; Bailey, M.G.

1991-01-01

In this paper a drilling fluid surface system design concept is proposed that resolves the Environmental, occupational hygiene and safety issues associated with conventional designs. Automation of the chemical handling and dosing system is the central element of the concept which, when fully integrated into the system, permits a significant reduction in the surface volume requirements. This, in turn, results in weight and capital cost savings, offsetting the cost of the processing and treatment plant, and a smaller overall footprint for the system. Adoption of the design philosophy results in a safe, healthy working environment in which all of the waste streams are managed so as to minimize the overall environmental impact of the drilling process

Deployment Testing of the De-Orbit Sail Flight Hardware

OpenAIRE

Hillebrandt, Martin; Meyer, Sebastian; Zander, Martin; Hühne, Christian

2015-01-01

The paper describes the results of the deployment testing of the De-Orbit Sail flight hardware, a drag sail for de-orbiting applications, performed by DLR. It addresses in particular the deployment tests of the fullscale sail subsystem and deployment force tests performed on the boom deployment module. For the fullscale sail testing a gravity compensation device is used which is described in detail. It allows observations of the in-plane interaction of the booms with the sail membrane and the...

Next generation sensing platforms for extended deployments in large-scale, multidisciplinary, adaptive sampling and observational networks

Science.gov (United States)

Cross, J. N.; Meinig, C.; Mordy, C. W.; Lawrence-Slavas, N.; Cokelet, E. D.; Jenkins, R.; Tabisola, H. M.; Stabeno, P. J.

2016-12-01

New autonomous sensors have dramatically increased the resolution and accuracy of oceanographic data collection, enabling rapid sampling over extremely fine scales. Innovative new autonomous platofrms like floats, gliders, drones, and crawling moorings leverage the full potential of these new sensors by extending spatiotemporal reach across varied environments. During 2015 and 2016, The Innovative Technology for Arctic Exploration Program at the Pacific Marine Environmental Laboratory tested several new types of fully autonomous platforms with increased speed, durability, and power and payload capacity designed to deliver cutting-edge ecosystem assessment sensors to remote or inaccessible environments. The Expendable Ice-Tracking (EXIT) gloat developed by the NOAA Pacific Marine Environmental Laboratory (PMEL) is moored near bottom during the ice-free season and released on an autonomous timer beneath the ice during the following winter. The float collects a rapid profile during ascent, and continues to collect critical, poorly-accessible under-ice data until melt, when data is transmitted via satellite. The autonomous Oculus sub-surface glider developed by the University of Washington and PMEL has a large power and payload capacity and an enhanced buoyancy engine. This 'coastal truck' is designed for the rapid water column ascent required by optical imaging systems. The Saildrone is a solar and wind powered ocean unmanned surface vessel (USV) developed by Saildrone, Inc. in partnership with PMEL. This large-payload (200 lbs), fast (1-7 kts), durable (46 kts winds) platform was equipped with 15 sensors designed for ecosystem assessment during 2016, including passive and active acoustic systems specially redesigned for autonomous vehicle deployments. The senors deployed on these platforms achieved rigorous accuracy and precision standards. These innovative platforms provide new sampling capabilities and cost efficiencies in high-resolution sensor deployment

IPv6 deployment and management

CERN Document Server

Dooley, Michael

2013-01-01

A guide for understanding, deploying, and managing Internet Protocol version 6 The growth of the Internet has created a need for more addresses than are available with Internet Protocol version 4 (IPv4)-the protocol currently used to direct almost all Internet traffic. Internet Protocol version 6 (IPv6)-the new IP version intended to ultimately succeed IPv4-will expand the addressing capacity of the Internet to support the explosive growth of users and devices on the Internet as well as add flexibility to allocating addresses and efficiency for routing traffic. IPv6 Deploy

Deploying Node.js

CERN Document Server

Pasquali, Sandro

2015-01-01

If you are an intermediate or advanced developer deploying your Node.js applications, then this book is for you. If you have already built a Node application or module and want to take your knowledge to the next level, this book will help you find your way.

Verifying occulter deployment tolerances as part of NASA's technology development for exoplanet missions

Science.gov (United States)

Kasdin, N. J.; Lisman, D.; Shaklan, S.; Thomson, M.; Webb, D.; Cady, E.; Marks, G. W.; Lo, A.

2013-09-01

An external occulter is a satellite employing a large screen, or starshade, that flies in formation with a spaceborne telescope to provide the starlight suppression needed for detecting and characterizing exoplanets. Among the advantages of using an occulter are the broadband allowed for characterization and the removal of light before entering the observatory, greatly relaxing the requirements on the telescope and instrument. In support of NASA's Exoplanet Exploration Program and the Technology Development for Exoplanet Missions (TDEM), we recently completed a 2 year study of the manufacturability and metrology of starshade petals. In this paper we review the results of that successful first TDEM which demonstrated an occulter petal could be built and measured to an accuracy consistent with close to 10-10 contrast. We then present the results of our second TDEM to demonstrate the next critical technology milestone: precision deployment of the central truss and petals to the necessary accuracy. We show the deployment of an existing deployable truss outfitted with four sub-scale petals and a custom designed central hub.

Accounting for variation in wind deployment between Canadian provinces

International Nuclear Information System (INIS)

Ferguson-Martin, Christopher J.; Hill, Stephen D.

2011-01-01

Wind energy deployment varies widely across regions and this variation cannot be explained by differences in natural wind resources alone. Evidence suggests that institutional factors beyond physical wind resources can influence the deployment of wind energy systems. Building on the work of , this study takes a historical institutionalist approach to examine the main factors influencing wind energy deployment across four Canadian provinces Canada: Alberta, Manitoba, Ontario and Nova Scotia. Our case studies suggest that wind energy deployment depends upon a combination of indirect causal factors-landscape values, political and social movements, government electricity policy, provincial electricity market structure and incumbent generation technologies and direct causal factors-grid architecture, ownership patterns, renewable incentive programs, planning and approvals processes and stakeholder support and opposition. - Research highlights: → Examines the reasons for variations in wind deployment between Canadian provinces. → Employs a historical institutional approach to the analysis. → Discusses social factors that affect wind deployment across Canadian jurisdictions.

Food packaging design

NARCIS (Netherlands)

Dekker, M.

2007-01-01

'Food product design - An integrated approach' deals with food product design from a technological perspective. It presents creative techniques for the innovation process and structured methodologies to translate consumer wishes into product properties based on Quality Function Deployment.

Integrated care services: lessons learned from the deployment of the NEXES project.

Science.gov (United States)

Hernández, Carme; Alonso, Albert; Garcia-Aymerich, Judith; Grimsmo, Anders; Vontetsianos, Theodore; García Cuyàs, Francesc; Altes, Anna Garcia; Vogiatzis, Ioannis; Garåsen, Helge; Pellise, Laura; Wienhofen, Leendert; Cano, Isaac; Meya, Montserrat; Moharra, Montserrat; Martinez, Joan Ignasi; Escarrabill, Juan; Roca, Josep

2015-01-01

To identify barriers to deployment of four articulated Integrated Care Services supported by Information Technologies in three European sites. The four services covered the entire spectrum of severity of illness. The project targeted chronic patients with obstructive pulmonary disease, cardiac failure and/or type II diabetes mellitus. One health care sector in Spain (Barcelona) (n = 11.382); six municipalities in Norway (Trondheim) (n = 450); and one hospital in Greece (Athens) (n = 388). The four services were: (i) Home-based long-term maintenance of rehabilitation effects (n = 337); (ii) Enhanced Care for frail patients, n = 1340); (iii) Home Hospitalization and Early Discharge (n = 2404); and Support for remote diagnosis (forced spirometry testing) in primary care (Support) (n = 8139). Both randomized controlled trials and pragmatic study designs were combined. Two technological approaches were compared. The Model for Assessment of Telemedicine applications was adopted. The project demonstrated: (i) Sustainability of training effects over time in chronic patients with obstructive pulmonary disease (p management, technological approach and legal issues were major factors modulating the success of the deployment. The project generated a business plan to foster service sustainability and health innovation. Deployment strategies require site-specific adaptations.

Simulating CubeSat Structure Deployment Dynamics, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — There is high value in simulating the nonlinear dynamics of stowing, deploying, and performance of deployable space structures, especially given the profound...

Multi-objective optimization design of air distribution of grate cooler by entropy generation minimization and genetic algorithm

International Nuclear Information System (INIS)

Shao, Wei; Cui, Zheng; Cheng, Lin

2016-01-01

Highlights: • A multi-objective optimization model of air distribution of grate cooler by genetic algorithm is proposed. • Pareto Front is obtained and validated by comparing with operating data. • Optimal schemes are compared and selected by engineering background. • Total power consumption after optimization decreases 61.10%. • Thickness of clinker on three grate plates is thinner. - Abstract: The cooling air distributions of grate cooler exercise a great influence on the clinker cooling efficiency and power consumption of cooling fans. A multi-objective optimization model of air distributions of grate cooler with cross-flow heat exchanger analogy is proposed in this paper. Firstly, thermodynamic and flow models of clinker cooling process is carried out. Then based on entropy generation minimization analysis, modified entropy generation numbers caused by heat transfer and pressure drop are chosen as objective functions respectively which optimized by genetic algorithm. The design variables are superficial velocities of air chambers and thicknesses of clinker layers on different grate plates. A set of Pareto optimal solutions which two objectives are optimized simultaneously is achieved. Scattered distributions of design variables resulting in the conflict between two objectives are brought out. The final optimal air distribution and thicknesses of clinker layers are selected from the Pareto optimal solutions based on power consumption of cooling fans minimization and validated by measurements. Compared with actual operating scheme, the total air volumes of optimized schemes decrease 2.4%, total power consumption of cooling fans decreases 61.1% and the outlet temperature of clinker decreases 122.9 °C which shows a remarkable energy-saving effect on energy consumption.

Medium access control and hardware prototype designs for low-energy wireless sensor networks

Energy Technology Data Exchange (ETDEWEB)

Kohvakka, M.

2009-07-01

A Wireless Sensor Network (WSN) is an emerging technology consisting of small, cheap, and ultra-low energy sensor nodes, which cooperatively monitor physical quantities, actuate, and perform data processing tasks. A deployment may comprise thousands of randomly distributed autonomous nodes, which must self-configure and create a multi-hop network topology.This thesis focuses on low-energy WSNs targeting to long network lifetime. The main research problem is the combination of adaptive and scalable multi-hop networking with constrained energy budget, processing power, and communication bandwidth. The research problem is approached by energy-efficient protocols and low-power sensor node platforms. The main contribution of this thesis is an energy-efficient Medium Access Control (MAC) design for TUTWSN (Tampere University of Technology Wireless Sensor Network). The design comprises channel access and networking mechanisms, which specify data exchange, link synchronization, network self-configuration, and neighbor discovery operations. The second outcome are several low-power sensor node platforms, which have been designed and implemented to evaluate the performance of the MAC design and hardware components in real deployments. The third outcome are the performance models and analysis of several MAC designs including TUTWSN, IEEE 802.15.4, and the most essential research proposals.The results and conclusion of this Thesis indicate that it is possible to implement multi-hop WSNs in harsh and dynamic operation conditions with years of lifetime using current low-cost components and batteries. Energy analysis results indicate that the lowest energy consumption is achieved by using simple and high data-rate transceivers. It is also critical to minimize sleep mode power consumption of all components and to use accurate wake-up timers. However, the selection of components constitutes only a minor part of the solution, and an energy-efficient MAC layer design being able to

Technological Minimalism: A Cost-Effective Alternative for Course Design and Development.

Science.gov (United States)

Lorenzo, George

2001-01-01

Discusses the use of minimum levels of technology, or technological minimalism, for Web-based multimedia course content. Highlights include cost effectiveness; problems with video streaming, the use of XML for Web pages, and Flash and Java applets; listservs instead of proprietary software; and proper faculty training. (LRW)

Modelling multi-rotor UAVs swarm deployment using virtual pheromones

Science.gov (United States)

Pujol, Mar; Rizo, Ramón; Rizo, Carlos

2018-01-01

In this work, a swarm behaviour for multi-rotor Unmanned Aerial Vehicles (UAVs) deployment will be presented. The main contribution of this behaviour is the use of a virtual device for quantitative sematectonic stigmergy providing more adaptable behaviours in complex environments. It is a fault tolerant highly robust behaviour that does not require prior information of the area to be covered, or to assume the existence of any kind of information signals (GPS, mobile communication networks …), taking into account the specific features of UAVs. This behaviour will be oriented towards emergency tasks. Their main goal will be to cover an area of the environment for later creating an ad-hoc communication network, that can be used to establish communications inside this zone. Although there are several papers on robotic deployment it is more difficult to find applications with UAV systems, mainly because of the existence of various problems that must be overcome including limitations in available sensory and on-board processing capabilities and low flight endurance. In addition, those behaviours designed for UAVs often have significant limitations on their ability to be used in real tasks, because they assume specific features, not easily applicable in a general way. Firstly, in this article the characteristics of the simulation environment will be presented. Secondly, a microscopic model for deployment and creation of ad-hoc networks, that implicitly includes stigmergy features, will be shown. Then, the overall swarm behaviour will be modeled, providing a macroscopic model of this behaviour. This model can accurately predict the number of agents needed to cover an area as well as the time required for the deployment process. An experimental analysis through simulation will be carried out in order to verify our models. In this analysis the influence of both the complexity of the environment and the stigmergy system will be discussed, given the data obtained in the

QUALITY FUNCTION DEPLOYMENT AS A STRATEGIC PLANNINGTOOL

Directory of Open Access Journals (Sweden)

Burcu DEVRİM İÇTENBAŞ

2011-07-01

Full Text Available Quality Function Deployment (QFD uses a house of quality to translate customerrequirements into engineering specifications. QFD has been widely used as a toolto develop new products. It has been adopted in thefields of education quality,service quality, software development and marketingplanning. The tool hasrecently been applied in strategic planning .In this study authors reviewed currentresearch which uses QFD as a strategic planning tool and described how QFDmethods can be used as a robust tool in strategic planning. This study provides aninsight for strategic planners to utilize a QFD- based philosophy and the methodsare useful tools for the design of a customer-driven strategy and show how itsystematically translates vision into action, targeting opportunities and creatinginnovative strategies.

Multiobjective Shape Optimization for Deployment and Adjustment Properties of Cable-Net of Deployable Antenna

Directory of Open Access Journals (Sweden)

Guoqiang You

2015-01-01

Full Text Available Based on structural features of cable-net of deployable antenna, a multiobjective shape optimization method is proposed to help to engineer antenna’s cable-net structure that has better deployment and adjustment properties. In this method, the multiobjective optimum mathematical model is built with lower nodes’ locations of cable-net as variables, the average stress ratio of cable elements and strain energy as objectives, and surface precision and natural frequency of cable-net as constraints. Sequential quadratic programming method is used to solve this nonlinear mathematical model in conditions with different weighting coefficients, and the results show the validity and effectiveness of the proposed method and model.

Deployment Repeatability

Science.gov (United States)

2016-08-31

large cohort of trials to spot unusual cases. However, deployment repeatability is inherently a nonlinear phenomenon, which makes modeling difficult...and GEMS tip position were both tracked during ground testing by a laser target tracking system. Earlier SAILMAST testing in 2005 [8] used...recalls the strategy used by SRTM, where a constellation of lights was installed at the tip of the boom and a modified star tracker was used to track tip

A distributed parallel genetic algorithm of placement strategy for virtual machines deployment on cloud platform.

Science.gov (United States)

Dong, Yu-Shuang; Xu, Gao-Chao; Fu, Xiao-Dong

2014-01-01

The cloud platform provides various services to users. More and more cloud centers provide infrastructure as the main way of operating. To improve the utilization rate of the cloud center and to decrease the operating cost, the cloud center provides services according to requirements of users by sharding the resources with virtualization. Considering both QoS for users and cost saving for cloud computing providers, we try to maximize performance and minimize energy cost as well. In this paper, we propose a distributed parallel genetic algorithm (DPGA) of placement strategy for virtual machines deployment on cloud platform. It executes the genetic algorithm parallelly and distributedly on several selected physical hosts in the first stage. Then it continues to execute the genetic algorithm of the second stage with solutions obtained from the first stage as the initial population. The solution calculated by the genetic algorithm of the second stage is the optimal one of the proposed approach. The experimental results show that the proposed placement strategy of VM deployment can ensure QoS for users and it is more effective and more energy efficient than other placement strategies on the cloud platform.

A Distributed Parallel Genetic Algorithm of Placement Strategy for Virtual Machines Deployment on Cloud Platform

Directory of Open Access Journals (Sweden)

Yu-Shuang Dong

2014-01-01

Full Text Available The cloud platform provides various services to users. More and more cloud centers provide infrastructure as the main way of operating. To improve the utilization rate of the cloud center and to decrease the operating cost, the cloud center provides services according to requirements of users by sharding the resources with virtualization. Considering both QoS for users and cost saving for cloud computing providers, we try to maximize performance and minimize energy cost as well. In this paper, we propose a distributed parallel genetic algorithm (DPGA of placement strategy for virtual machines deployment on cloud platform. It executes the genetic algorithm parallelly and distributedly on several selected physical hosts in the first stage. Then it continues to execute the genetic algorithm of the second stage with solutions obtained from the first stage as the initial population. The solution calculated by the genetic algorithm of the second stage is the optimal one of the proposed approach. The experimental results show that the proposed placement strategy of VM deployment can ensure QoS for users and it is more effective and more energy efficient than other placement strategies on the cloud platform.

Development document for best technology available for the location, design, construction, and capacity of cooling water intake structures for minimizing adverse environmental impact

International Nuclear Information System (INIS)

Train, R.E.; Breidenbach, A.W.; Hall, E.P.; Barnes, D.

1976-04-01

This document presents the findings of an extensive study of the available technology for the location, design construction and capacity of cooling water intake structures for minimizing adverse environmental impact, in compliance with and to implement Section 316(b) of the Federal Water Pollution Control Act Amendments of 1972

Minimally inconsistent reasoning in Semantic Web.

Directory of Open Access Journals (Sweden)

Xiaowang Zhang