Characterization of prealloyed copper powders treated in high energy ball mill

International Nuclear Information System (INIS)

Rajkovic, Viseslava; Bozic, Dusan; Jovanovic, Milan T.

2006-01-01

The inert gas atomised prealloyed copper powders containing 3.5 wt.% Al were milled up to 20 h in the planetary ball mill in order to oxidize aluminium in situ with oxygen from the air. In the next procedure compacts from milled powder were synthesized by hot-pressing in argon atmosphere. Compacts from as-received Cu-3.5 wt.% Al powder and electrolytic copper powder were also prepared under the same conditions. Microstructural and morphological changes of high energy milled powder as well as changes of thermal stability and electrical conductivity of compacts were studied as a function of milling time and high temperature exposure at 800 deg. C. Optical, scanning electron microscopy (SEM) and X-ray diffraction analysis were performed for microstructural characterization, whereas thermal stability and electrical conductivity were evaluated by microhardness measurements and conductometer Sigmatest, respectively. The prealloyed 5 h-milled and compacted powder showed a significant increase in microhardness reaching the value of 2600 MPa, about 4 times greater than that of compacts synthesized from as-received electrolytic copper powder (670 MPa). The electrical conductivity of compacts from 5 h-milled powder was 52% IACS. The results were discussed in terms of the effect of small grain size and finely distributed alumina dispersoids on hardening and thermal stability of compacts

Milling condition effects on the Nd15 Fe77 B8 powder magnetic properties

International Nuclear Information System (INIS)

Landgraf, Fernando J.G.; Missell, Frank P.

1992-01-01

As a result of the first part of a study of the development of permanent magnets, an investigation of the effect of milling on the magnetic properties of the alloy Nd 15 Fe 77 B 8 showed differences in efficiency between ball milling and vibration milling, as well as a dependence of the intrinsic coercive field on particle size. The maximum value of the coercive field was obtained for a particle size of 1.7 μm in samples compacted without magnetic orientation. (author)

Agglomeration during wet milling of LAST (lead-antimony-silver-tellurium) powders

International Nuclear Information System (INIS)

Hall, B.D.; Case, E.D.; Ren, F.; Johnson, J.R.; Timm, E.J.

2009-01-01

LAST (lead-antimony-silver-tellurium) compounds comprise a family of semiconducting materials with good thermoelectric properties. However, the as-cast form of LAST exhibits large grain size and hence low mechanical strength. Powder processing can produce a fine powder particle size that enhances fracture strength, however the powders tend to agglomerate if the individual powder diameters are less than a few microns across. Dry milling or wet milling (hexane additions of 0 cm 3 and 10 cm 3 ) produced hard agglomerates roughly 40 μm in diameter while wet milling with hexane additions of 25 cm 3 , 30 cm 3 or 50 cm 3 resulted in small, porous agglomerates roughly 20 μm in diameter. Thus, by adjusting the amount of milling liquid used while milling LAST powders, one can shift from hard to soft agglomerates, where the literature shows that soft agglomerates are less harmful to the final, sintered product. Also, in agreement with the results from the literature on other materials, wet milling of LAST powders produced smaller particle sizes but required longer times to reach the grindability limit

Characterization of structures and novel magnetic response of Fe87.5Si7Al5.5 alloy processed by ball milling

International Nuclear Information System (INIS)

Duan, Yuping; Gu, Shuchao; Zhang, Zhonglun; Wen, Ming

2012-01-01

Highlights: ► The water atomized Fe 87.5 Si 7 Al 5.5 (Wt.%) alloy was processed by ball-milling. ► The microstructure and magnetic properties of alloy changed following milling. ► The powders milled for 10 h have the largest M s and strongest reflection loss. ► The permeability of the powders milled for 2 h is the largest. ► The charge exchange between Fe and Si is discussed base on first-principles. - Abstract: The water atomized Fe 87.5 Si 7 Al 5.5 (Wt.%) alloy was processed by a high-energy planetary ball-milling. The characterization of morphology, microstructure, and electromagnetic properties were measured by scanning electron microscope (SEM), X-ray diffractometer, vibrating sample magnetometer (VSM), vector network analyzer and the first principle method. The analysis results showed that the powders shape became flaky from fusiform. The powders showed a reduction of the average grain size and the increase of the internal strain, and then presented an adverse variation trend after 55 h milling. The powders that milled 10 h had the largest saturation magnetization M S (131 emu/g). The value μ′ of the powders decreased with increasing milling time at relatively lower frequency (2–8 GHz), but opposite variation tendency happened at higher frequency (8–18 GHz). Also, only short time milling can enhance the value of μ″ in the test frequency. The powders after 10 h milling showed excellent microwave absorption (RL < −10 dB) at the frequency 9.0–15.6 GHz and the absorption peak shifted regularly to the high frequency as the increased milling time. Furthermore, the effect of charge exchange between the Fe and Si on the saturation magnetization in the ball-milling process was also investigated by using density functional theory (DFT) of first principle.

Phase Transitions in Mechanically Milled Mn-Al-C Permanent Magnets

Directory of Open Access Journals (Sweden)

Michael J. Lucis

2014-04-01

Full Text Available Mn-Al powders were prepared by rapid solidification followed by high-energy mechanical milling. The rapid solidification resulted in single-phase ε. The milling was performed in both the ε phase and the τ phase, with the τ-phase formation accomplished through a heat treatment at 500 °C for 10 min. For the ε-milled samples, the conversion of the ε to the τ phase was accomplished after milling via the same heat treatment. Mechanical milling induced a significant increase in coercivity in both cases, reaching 4.5 kOe and 4.1 kOe, respectively, followed by a decrease upon further milling. The increase in coercivity was the result of grain refinement induced by the high-energy mechanical milling. Additionally, in both cases a loss in magnetization was observed. Milling in the ε phase showed a smaller decrease in the magnetization due to a higher content of the τ phase. The loss in magnetization was attributed to a stress-induced transition to the equilibrium phases, as no site disorder or oxidation was observed. Surfactant-assisted milling in oleic acid also improved coercivity, but in this case values reached >4 kOe and remained stable at least through 32 h of milling.

Normal and abnormal grain growth in fine-grained Nd-Fe-B sintered magnets prepared from He jet milled powders

Energy Technology Data Exchange (ETDEWEB)

Bittner, F., E-mail: f.bittner@ifw-dresden.de [IFW Dresden, Institute for Metallic Materials, PO Box 270116, 01171 Dresden (Germany); Technische Universität Dresden, Institute of Materials Science, 01062 Dresden (Germany); Woodcock, T.G. [IFW Dresden, Institute for Metallic Materials, PO Box 270116, 01171 Dresden (Germany); Schultz, L. [IFW Dresden, Institute for Metallic Materials, PO Box 270116, 01171 Dresden (Germany); Technische Universität Dresden, Institute of Materials Science, 01062 Dresden (Germany); Schwöbel, C. [Technische Universität Darmstadt, Materialwissenschaft, Alarich-Weiß-Str. 16, 64287 Darmstadt (Germany); Gutfleisch, O. [Technische Universität Darmstadt, Materialwissenschaft, Alarich-Weiß-Str. 16, 64287 Darmstadt (Germany); Fraunhofer ISC, Projektgruppe für Werkstoffkreisläufe und Ressourcenstrategie IWKS, Rodenbacher Chaussee 4, 63457 Hanau (Germany); Zickler, G.A.; Fidler, J. [Technische Universität Wien, Institute of Solid State Physics, Wiedner Hauptstr. 8-10, 1040 Wien (Austria); Üstüner, K.; Katter, M. [Vacuumschmelze GmbH & Co. KG, 63412 Hanau (Germany)

2017-03-15

Fine-grained, heavy rare earth free Nd-Fe-B sintered magnets were prepared from He jet milled powders with an average particle size of 1.5 µm by low temperature sintering at 920 °C or 980 °C. A coercivity of >1600 kA/m was achieved for an average grain size of 1.68 µm. Transmission electron microscopy showed that the distribution and composition of intergranular and grain boundary junction phases was similar to that in conventionally processed magnets. Microstructural analysis on different length scales revealed the occurrence of abnormal grain growth, which is unexpected for sintering temperatures below 1000 °C. A larger area fraction of abnormal grains was observed in the sample sintered at 920 °C compared to that sintered at 980 °C. Microtexture investigation showed a better crystallographic alignment of the abnormal grains compared to the fine-grained matrix, which is explained by a size dependent alignment of the powder particles during magnetic field alignment prior to sintering. Slightly larger particles in the initial powder show a better alignment and will act as nucleation sites for abnormal grain growth. Magneto-optical Kerr investigations confirmed the lower switching field of the abnormal grains compared to the fine-grained matrix. The demagnetisation curve of the sample sintered at 920 °C showed reduced rectangularity and this was attributed to a cooperative effect of the larger fraction of abnormal grains with low switching field and, as a minor effect, a reduced degree of crystallographic texture in this sample compared to the material sintered at 980 °C, which did not show the reduced rectangularity of the demagnetisation curve. - Highlights: • He Jet milling to reduce Nd-Fe-B grain size and to enhance coercivity. • Normal and abnormal grain growth observed for low temperature sintering. • Well oriented abnormal grown grains explained by size dependent field alignment. • Poor rectangularity is caused by low nucleation field of

Normal and abnormal grain growth in fine-grained Nd-Fe-B sintered magnets prepared from He jet milled powders

International Nuclear Information System (INIS)

Bittner, F.; Woodcock, T.G.; Schultz, L.; Schwöbel, C.; Gutfleisch, O.; Zickler, G.A.; Fidler, J.; Üstüner, K.; Katter, M.

2017-01-01

Fine-grained, heavy rare earth free Nd-Fe-B sintered magnets were prepared from He jet milled powders with an average particle size of 1.5 µm by low temperature sintering at 920 °C or 980 °C. A coercivity of >1600 kA/m was achieved for an average grain size of 1.68 µm. Transmission electron microscopy showed that the distribution and composition of intergranular and grain boundary junction phases was similar to that in conventionally processed magnets. Microstructural analysis on different length scales revealed the occurrence of abnormal grain growth, which is unexpected for sintering temperatures below 1000 °C. A larger area fraction of abnormal grains was observed in the sample sintered at 920 °C compared to that sintered at 980 °C. Microtexture investigation showed a better crystallographic alignment of the abnormal grains compared to the fine-grained matrix, which is explained by a size dependent alignment of the powder particles during magnetic field alignment prior to sintering. Slightly larger particles in the initial powder show a better alignment and will act as nucleation sites for abnormal grain growth. Magneto-optical Kerr investigations confirmed the lower switching field of the abnormal grains compared to the fine-grained matrix. The demagnetisation curve of the sample sintered at 920 °C showed reduced rectangularity and this was attributed to a cooperative effect of the larger fraction of abnormal grains with low switching field and, as a minor effect, a reduced degree of crystallographic texture in this sample compared to the material sintered at 980 °C, which did not show the reduced rectangularity of the demagnetisation curve. - Highlights: • He Jet milling to reduce Nd-Fe-B grain size and to enhance coercivity. • Normal and abnormal grain growth observed for low temperature sintering. • Well oriented abnormal grown grains explained by size dependent field alignment. • Poor rectangularity is caused by low nucleation field of

Fabrication of Ti-Ni-Cu shape memory alloy powders by ball milling method

International Nuclear Information System (INIS)

Kang, S.; Nam, T.

2001-01-01

Ti-Ni and Ti-Ni-Cu shape memory alloy powders have been fabricated by ball milling method, and then alloying behavior and transformation behavior were investigated by means of optical microscopy, electron microscopy, X-ray diffraction and differential scanning calorimetry. As milled Ti-Ni powders fabricated with milling time less than 20 hrs was a mixture of pure elemental Ti and Ni, and therefore it was unable to obtain alloy powders because the combustion reaction between Ti and Ni occurred during heat treatment. Since those fabricated with milling time more than 20 hrs was a mixture of Ti-rich and Ni-rich Ti-Ni solid solution, however, it was possible to obtain alloy powders without the combustion reaction during heat treatment. Clear exothermic and endothermic peaks appeared in the cooling and heating curves, respectively in DSC curves of 20 hrs and 30 hrs milled Ti-Ni powders. On the other hand, in DSC curves of 1 hr, 10 hrs, 50 hrs and 100 hrs, the thermal peaks were almost discernible. The most optimum ball milling time for fabricating Ti-Ni alloy powders was 30 hrs. Ti-40Ni-10Cu(at%) alloy powders were fabricated successfully by ball milling conditions with rotating speed of 100 rpm and milling time of 30 hrs. (author)

Design and Testing of UMM Vertical Ball Mill (UVBM) for producing Aluminium Powder

Science.gov (United States)

Aisyah, I. S.; Caesarendra, Wahyu; Suprihanto, Agus

2018-04-01

UMM Vertical Ball Mill (UVBM) was intended to be the apparatus to produce metal powder with superior characteristic in production rate while retaining good quality of metal powder. The concept of design was adopting design theory of Phal and Beitz with emphasis on increasing of probability of success in engineering and economy aspects.Since it was designed as vertical ball mill, a new way to produce powder, then it need to be tested for the performance after manufactured. The test on UVBM was carried out by milling of aluminium chip for 5 (five) different milling time of 0.5 hours, 1 hour, 3 hours, 5 hours and 7 hours, and the powder product then be characterized for it morphology and size using Scanning Electron Microscope (SEM) and Sieve.The results of the study were the longer of the milling time, the finer of the powder. From the test results of SEM, the morphology of the powder with 5 variations of milling time were most of the powder in form of flake (flat), small round and angular (irregular). The distribution of powder size was best obtained on the variation of milling time 3 hours, 5 hours, and 7 hours with percentage of 200 mesh in size of 22.14 %, 64 % and 91.25 % respectively.

Preparation and properties of Cobalt-based soft magnetic material prepared by novel powder metallurgy

Energy Technology Data Exchange (ETDEWEB)

Srivastava, Yogesh, E-mail: 123209001_yogesh@manit.ac.in; Srivastava, Sanjay

2017-02-01

The present work deals with the development of nanocrystalline 60Co–26Fe–14Al (wt%) soft magnetic materials via mechanical milling of elemental powders. The evolution of solid solution during milling proceeded with continuous decrease in atomic order and the crystallite size, and an introduction of internal strain and dislocations. The milling-induced lattice defects, crystallite size reduction, and atomic disorder exhibited a decrease in saturation magnetization, remanence magnetization, squareness ratio, and blocking temperature with increasing milling time. It has been demonstrated that, at subzero temperatures, the magnetization decreases with increasing temperature due to the development of an effective anisotropy caused by an evolution of canted spin structure owing to the introduction of lattice defects during milling. - Highlights: • Co-based HA have been fabricated by mechanical alloying. • The effect of milling time was investigated. • The saturation magnetization can be reached up to 140.79 emu/g.

Structural and magnetic properties of Co50Ni50 powder mixtures

International Nuclear Information System (INIS)

Loudjani, N.; Bensebaa, N.; Dekhil, L.; Alleg, S.; Sunol, J.J.

2011-01-01

In the present work, morphological, structural, thermal and magnetic properties of nanocrystalline Co 50 Ni 50 alloy prepared by high energy planetary ball milling have been studied by means of scanning electron microscopy, X-ray diffraction, and differential scanning calorimetry. The coercivity and the saturation magnetization of alloyed powders were measured at room temperature by a vibration sample magnetization. Morphological observations indicated a narrow distribution in the particle and homogeneous shape form with mean average particle size around 130 μm 2 . The results show that an allotropic Co transformation hcp→fcc occurs within the three first hours of milling and contrary to what expected, the Rietveld refinement method reveals the formation of two fcc solid solutions (SS): fcc Co(Ni) and Ni(Co) beside a small amount of the undissolved Co hcp. Thermal measurement, as a function of milling time was carried out to confirm the existence of the hcp phase and to estimate its amount. Magnetic measurement indicated that the 48 h milled powders with a steady state particles size have the highest saturation (105.3 emu/g) and the lowest coercivity (34.5 Oe). - Highlights: → By using the Rietveld refinement method we found that Co 50 Ni 50 alloy, milled for 48 h, contains two fcc solid solutions: fcc Co(Ni) and Ni(Co), beside a small amount of the undissolved Co hcp. DSC measurement as a function of milling time was carried out to confirm the existence of the hcp phase and to estimate its amount. → By means of imageJ we found the area distribution and not just the diameter distribution. → The coercivity is strongly related to the particles size distribution.

Production of nanocrystalline cermet thermal spray powders for wear resistant coatings by high-energy milling

International Nuclear Information System (INIS)

Eigen, N.; Klassen, T.; Aust, E.; Bormann, R.; Gaertner, F.

2003-01-01

TiC-Ni based nanocrystalline cermet powders for thermal spraying were produced by high-energy milling. Milling experiments were performed in an attrition mill and a vibration mill in kilogram scale, and powder morphologies and microstructures were characterized using scanning electron microscopy, X-ray diffraction, and laser scattering for particle size analysis. Milling time and powder input were optimized with respect to the desired microstructure and particle sizes, and the results using both types of mill were compared. Powders with homogeneously dispersed hard phase particles below 300 nm could be produced in both mills. Additional processes for the refinement of powder morphology and particle size distribution are discussed

Nd-Fe-B sintered magnets fabrication by using atomized powders

International Nuclear Information System (INIS)

Goto, R; Sugimoto, S; Matsuura, M; Tezuka, N; Une, Y; Sagawa, M

2011-01-01

Nd-Fe-B sintered magnets are required to achieve high coercivity for improvement of their thermal stability. Dy is added to increase coercivity, however, this element decrease magnetization and energy products. Therefore, Dy-lean Nd-Fe-B sintered magnets with high coercivity are strongly demanded. To increase coercivity, it is necessary that microstructure of sintered magnets is consisted of both fine main phase particles and homogeneously distributed Nd-rich phases around the main phase. To meet those requirements, Nd-Fe-B atomized powders were applied to the fabrication process of sintered magnets. Comparing with the case of using strip casting (SC) alloys, jet-milled powders from atomized powders show homogeneous distribution of Nd-rich phase. After optimized thermal treatment, coercivities of sintered magnets from atomized powders and SC alloys reach 1050 kA·m-1 and 1220 kA·m-1, respectively. This difference in coercivity was due to initial oxygen concentration of starting materials. Consequently, Nd-rich phases became oxides with high melting points, and did not melt and spread during sintering and annealing.

The Semi-Quantitative Study of Magnetization Process on Milling and Reannealing of Barium Hexaferrite (BaO.6Fe2O3

Directory of Open Access Journals (Sweden)

Ridwan

2009-07-01

Full Text Available Barium hexaferrite (BaO.6Fe2O3 is as a hard magnetic material with good chemical stability which has been intensively used as permanent magnet components. Many works have been done in order to improve their magnetic properties either through chemical process or powders metallurgy technique. In this work, commercial BaO.6Fe2O3 was milled using high-energy milling machine for 10, 20 and 30 hours and followed by reannealing for 3 hours at 1000⁰C in air. X-ray diffraction pattern indicate no phase decomposition occurred caused the mill processing, annealing of milled powders recovered the crystal system and promoted crystallite growth. The magnetic hysteresis curve measured by vibrating sample magnetometer (VSM shows the coercivity of annealed BaO.6Fe2O3 increases to two times higher than the original one. By using Jiles-Atherton model, all the hysteresis parameters Ms, k, α, a and c, have been determined adopted to the Genetic Algorithm (GA. The analyzed hysteretic parameters obtained from this work is congruent to the change of magnetic properties of as-milled and annealed powders of barium hexaferrite.

Response to Thermal Exposure of Ball-Milled Aluminum-Borax Powder Blends

Science.gov (United States)

Birol, Yucel

2013-04-01

Aluminum-borax powder mixtures were ball milled and heated above 873 K (600 °C) to produce Al-B master alloys. Ball-milled powder blends reveal interpenetrating layers of deformed aluminum and borax grains that are increasingly refined with increasing milling time. Thermal exposure of the ball-milled powder blends facilitates a series of thermite reactions between these layers. Borax, dehydrated during heating, is reduced by Al, and B thus generated reacts with excess Al to produce AlB2 particles dispersed across the aluminum grains starting at 873 K (600 °C). AlB2 particles start to form along the interface of the aluminum and borax layers. Once nucleated, these particles grow readily to become hexagonal-shaped crystals that traverse the aluminum grains with increasing temperatures as evidenced by the increase in the size as well as in the number of the AlB2 particles. Ball milling for 1 hour suffices to achieve a thermite reaction between borax and aluminum. Ball milling further does not impact the response of the powder blend to thermal exposure. The nucleation-reaction sites are multiplied, however, with increasing milling time and thus insure a higher number of smaller AlB2 particles. The size of the AlB2 platelets may be adjusted with the ball milling time.

Effect of Fe-Mn addition on microstructure and magnetic properties of NdFeB magnetic powders

Science.gov (United States)

Kurniawan, C.; Purba, A. S.; Setiadi, E. A.; Simbolon, S.; Warman, A.; Sebayang, P.

2018-03-01

In this paper, the effect of Fe-Mn alloy addition on microstructures and magnetic properties of NdFeB magnetic powders was investigated. Varied Fe-Mn compositions of 1, 5, and 10 wt% were mixed with commercial NdFeB type MQA powders for 15 minutes using shaker mill. The characterizations were performed by powder density, PSA, XRD, SEM, and VSM. The Fe-Mn addition increased the powder density of NdFeB/Fe-Mn powders. On the other side, particle size distribution slightly decreased as the Fe-Mn composition increases. Magnetic properties of NdFeB/Fe-Mn powders changed with the increasing of Fe-Mn content. SEM analysis showed the particle size of NdFeB/Fe-Mn powder was smaller as the Fe-Mn composition increases. It showed that NdFeB/Fe-Mn particles have different size and shape for NdFeB and Fe-Mn particles separately. The optimum magnetic properties of NdFeB/Fe-Mn powder was achieved on the 5 wt% Fe-Mn composition with remanence M r = 49.45 emu/g, coercivity H c = 2.201 kOe, and energy product, BH max = 2.15 MGOe.

Magnetic and microstructural properties of Fe{sub 3}O{sub 4}-coated Fe powder soft magnetic composites

Energy Technology Data Exchange (ETDEWEB)

Jo Sunday, Katie [Department of Materials Science and Engineering, Drexel University, Philadelphia, PA19104 (United States); Hanejko, Francis G. [Hoeganaes Corporation, Cinnaminson, NJ08077 (United States); Taheri, Mitra L., E-mail: mtaheri@coe.drexel.edu [Department of Materials Science and Engineering, Drexel University, Philadelphia, PA19104 (United States)

2017-02-01

Soft magnetic composites (SMCs) comprised of ferrite-coated ferrous powder permit isotropic magnetic flux capabilities, lower core losses, and complex designs through the use of traditional powder metallurgy techniques. Current coating materials and methods are vastly limited by the nonmagnetic properties of organic and some inorganic coatings and their inability to withstand high heat treatments for proper stress relief of core powder after compaction. Ferrite-based coatings are ferrimagnetic, highly resistive, and possess high melting temperatures, thus providing adequate electrical barriers between metallic particles. In this work, iron powder was coated with Fe{sub 3}O{sub 4} particles via mechanical milling, then compacted and cured in an inert gas environment. We find density and coercivity to improve with increasing temperatures; however, core loss greatly increases, which is attributed to the formation of a more conductive iron-oxide phase and less resistive Fe volume. Our work begins to exemplify the unique qualities and potential for ferrite-based coatings using traditional powder metallurgy techniques and higher curing temperatures for electromagnetic devices. - Highlights: • Fe{sub 3}O{sub 4}-coated Fe powder was produced via mechanical milling, then compacted and cured into composite form. • SEM/EDS confirm Fe particles are individually isolated with iron-oxide coating material. • Larger particle sizes show improved core loss and coercivity measurements. • We report good magnetic properties for compaction at 800 MPa and a curing temperature of 700 °C.

The effect of surfactant addition on high-energy milling upon the magnetic properties and microstructure of the Pr-Fe-B HDDR magnetic powders; Efeito da adicao de surfactantes nas propriedades e microestrutura de pos magneticos a base de Pr-Fe-B obtidos via HDDR e moagem de alta energia

Energy Technology Data Exchange (ETDEWEB)

Santos, P.B.; Silva, S.C.; Faria, R.N.; Takiishia, H., E-mail: pbsantos@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2010-07-01

Nanomagnetic powders based on the composition Pr{sub 12}Fe{sub 65.9}Co{sub 16}B{sub 6}Nb{sub 0.1} have been obtained from using (a) the hydrogenation, disproportionation, desorption and recombination (HDDR) process; (b) by varying of milling time and (c) with the addition of an oleic acid as a surfactant. The latter has been used to enhance milling condition by preventing the agglomeration of particles and hence to improve the intrinsic coercivity of the material. High-energy mechanical milling has been used to yield magnetic nanoparticles. Powders were characterized magnetically using vibrating sample magnetometer (VSM) and microstructurally by Scanning Electron Microscopy (SEM), Field Emission Gun SEM (FEG-SEM) and X-ray diffraction. (author)

Milling uranium silicide powder for dispersion nuclear fuels

Energy Technology Data Exchange (ETDEWEB)

Vieira, E.; Silva, D.G.; Souza, J.A.B.; Durazzo, M. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Riella, H.G. [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil)

2009-07-01

Full text: Uranium silicide (U3Si2) is presently considered the best fuel qualified so far in terms of uranium loading and performance. Stability of the U3Si2 fuel with uranium density of 4.8 g/cm3 was confirmed by burnup stability tests performed during the Reduced Enrichment for Research and Test Reactors (RERTR) program. This fuel was chosen to compose the first core of the new Brazilian Multipurpose Research Reactor (RMB), planned to be constructed in the next years. This new reactor will consume bigger quantities of U3Si2 powder, when compared with the small consumption of the IEA-R1 research reactor of IPEN-CNEN/SP, the unique MTR type research reactor operating in the country. At the present time, the milling operation of U3Si2 ingots is made manually. In order to increase the powder production capacity, the manual milling must be replaced by an automated procedure. This paper describes a new milling machine and procedure developed to produce U3Si2 powder with higher efficiency. (author)

Efek Waktu Wet Milling dan Suhu Annealing Terhadap Sifat Fisis, Mikrostruktur dan Magnet dari Flakes NdFeB

OpenAIRE

Sipahutar, Wahyu Solafide

2015-01-01

Had made research manufacture NdFeB magnets of flakes of wet milling process using a ball mill to the physic properties, microstructure, and magnetic properties with variations milling time is 16 hours, 24 hours, 48 hours, 72 hours. Powder result of mechanical milling using a ball mill and then analyzed the resulting particle size by using PSA and XRD. Then do the manufacture of test samples in the form of pellets by compaction process through print isotropy. Having obtained a sample of pelle...

Magnetic properties of ball-milled Fe0.6Mn0.1Al0.3 alloys

International Nuclear Information System (INIS)

Rebolledo, A.F.; Romero, J.J.; Cuadrado, R.; Gonzalez, J.M.; Pigazo, F.; Palomares, F.J.; Medina, M.H.; Perez Alcazar, G.A.

2007-01-01

The FeMnAl-disordered alloy system exhibits, depending on the composition and the temperature, a rich variety of magnetic phases including the occurrence of ferromagnetism, antiferromagnetism, paramagnetism and spin-glass and reentrant spin glass behaviors. These latter phases result from the presence of atomic disorder and magnetic dilution and from the competing exchange interactions taking place between an Fe atom and its Mn and Fe first neighbors. The use of mechanical alloying in order to prepare these alloys is specially interesting since it allows to introduce in a progressive way large amounts of disorder. In this work, we describe the evolution with the milling time of the temperature dependence of the magnetic properties of mechanically alloyed Fe 0.6 Mn 0.1 Al 0.3 samples. The materials were prepared in a planetary ball mill using a balls-to-powder mass ratio of 15:1 and pure (99.95 at%) Fe, Mn and Al powders for times up to 19 h. The X-rays diffraction (XRD) spectra show the coexistence of three phases at short milling times. For milling times over 6 h, only the FeMnAl ternary alloy BCC phase is observed. Moesbauer spectroscopy reveals the complete formation of the FeMnAl alloy after 9 h milling time. The magnetic characterization showed that all the samples were ferromagnetic at room temperature with coercivities decreasing from 105 Oe (3 h milled sample) down to 5 Oe in the case of the sample milled for 19 h

Behaviour of CaO coating of gas atomized Mg powders using mechanical milling process

International Nuclear Information System (INIS)

Kim, Sun-Mi; Kim, Yong Hwan; Kim, Young Do; Kim, Taek-Soo

2011-01-01

Highlights: → This work is very new, since behaviour of CaO coating with milling time as desulfurizer is not frequently reported. → The manuscript reports the new manner of Mg powders desulfurizer development by the innovative process. - Abstract: In order to synthesize a thermally stable Mg powder as a desulfurizer of iron, pure Mg was gas atomized to powders and coated by CaO powders, to produce a thermally stable desulfurizer using a mechanical milling process. Since the effect of desulfurization is dependent on the degree of surface modification, coating behaviours such as the size, morphology and layer thickness were investigated as a function of milling condition. As the milling conducted from 10 min to 30 min, 1 h, 3 h, 6 h, 12 h, CaO particles began to stick on the surface of Mg powders. The layer of CaO formed from 1 h milling was about 17 μm thick and gradually thickened to be 28 μm, 32 μm and 37 μm with increasing the milling time to 3 h, 6 h and 12 h, respectively. The shape of coated powder became more spherical after 1 h milling, being mostly spherical after 6 h. Desulfurization rate and uniformity were evaluated for the various thickness of the coating layer.

Effect of thermal treatment on mechanically milled cobalt powder

CSIR Research Space (South Africa)

Bolokang, AS

2012-03-01

Full Text Available Stabilization of the metastable FCC phase has been achieved after 10 h milled Co powder sintering at 1400 °C. Phase identification of the Co powders was performed by the X-ray diffraction analysis, while the microstructural analyses were performed...

Effects of powder flowability on the alignment degree and magnetic properties for NdFeB sintermagnets

Energy Technology Data Exchange (ETDEWEB)

Sun, Y. [School of Physics and Microelectronics, Shandong University, 250100 (China); Gao, R.W. [School of Physics and Microelectronics, Shandong University, 250100 (China)]. E-mail: gaorwbox@sdu.edu.cn; Han, G.B. [School of Physics and Microelectronics, Shandong University, 250100 (China); Bai, G. [School of Physics and Microelectronics, Shandong University, 250100 (China); Liu, T. [School of Physics and Microelectronics, Shandong University, 250100 (China); Wang, B. [School of Physics and Microelectronics, Shandong University, 250100 (China); Yantai Shougang Magnetic Material CO, LTD, 265500 (China)

2006-04-15

The magnetic powders for sintered NdFeB magnets have been prepared by using the strip casting (SC), hydrogen decrepitation (HD) and jet milling (JM) techniques. The effects of powder flowability and addition of a lubricant on the alignment degree and the hard magnetic properties of sintered magnets have been studied. The results show that the main factor affecting powder flowability is the aggregation of magnetic particles for powders in a loose state, but it is the friction between the powder particles for powders that are in a compact state. The addition of a lubricant with suitable dose can slightly prevent the congregating of powders, obviously decrease the friction between the powder particles, improve the powder flowability, and increase the alignment degree, remanence and energy product density of sintered magnets. Mixing a suitable dose of lubricant and adopting rubber isostatic pressing (RIP) with a pulse magnetic field, we have succeeded in producing the sintered NdFeB magnet with high hard magnetic properties of B {sub r}=14.57 KG, {sub j}H {sub c}=14.43 KOe (BH){sub max}=51.3 MGOe.

Flaking behavior and microstructure evolution of nickel and copper powder during mechanical milling in liquid environment

International Nuclear Information System (INIS)

Xiao Xiao; Zeng Zigao; Zhao Zhongwei; Xiao Songwen

2008-01-01

To prepare metal flakes with a high flaking level and investigate the microstructure of metal flakes, nickel and copper powder were mechanically milled in liquid environment and the microstructure of powders was investigated by X-ray diffraction. The milling process can be divided into flaking and broken stages. At the flaking stage, milled metal powders exhibited high flaking level and flaky microshape, and became preferred orientation. While at the broken stage, the milled powders presented a low flaking level and irregular microshape, and was not preferred orientation any longer. The grain size, microstrain and dislocation density along direction varied with milling time differently from that along direction. The flaking level of the milled powders was related to the preferred orientation, and more closely to the deformation mechanism. We can strengthen the formation of preferred orientation to obtain metal powders with a high flaking level

Cold compaction behavior and pressureless sinterability of ball milled WC and WC/Cu powders

Directory of Open Access Journals (Sweden)

Hashemi Seyed R.

2016-01-01

Full Text Available In this research, cold compaction behavior and pressureless sinterability of WC, WC-10%wtCu and WC-30%wtCu powders were investigated. WC and WC/Cu powders were milled in a planetary ball mill for 20h. The milled powders were cold compacted at 100, 200, 300 and 400 MPa pressures. The compressibility behavior of the powders was evaluated using the Heckel, Panelli-Ambrosio and Ge models. The results showed that the Panelli-Ambrosio was the preferred equation for description the cold compaction behavior of the milled WC and WC-30%wtCu powders. Also, the most accurate model for describing the compressibility of WC-10%wtCu powders was the Heckel equation. The cold compacts were sintered at 1400°C. It was found that by increasing the cold compaction pressure of powder compacts before sintering, the sinterability of WC-30%wtCu powder compacts was enhanced. However, the cold compaction magnitude was not affected significantly on the sinterability of WC and WC-10%wtCu powders. The microstructural investigations of the sintered samples by Scanning Electron Microscopy (SEM confirmed the presence of porosities at the interface of copper-tungsten carbide phases.

Flaking behavior and microstructure evolution of nickel and copper powder during mechanical milling in liquid environment

Energy Technology Data Exchange (ETDEWEB)

Xiao Xiao [College of Metallurgical Science and Engineering, Central South University, Changsha 410083, Hunan (China); Changsha Research Institute of Mining and Metallurgy, Changsha 410012, Hunan (China); Zeng Zigao [Changsha Research Institute of Mining and Metallurgy, Changsha 410012, Hunan (China); Zhao Zhongwei [College of Metallurgical Science and Engineering, Central South University, Changsha 410083, Hunan (China); Xiao Songwen [Changsha Research Institute of Mining and Metallurgy, Changsha 410012, Hunan (China)], E-mail: swinxiao@yahoo.com.cn

2008-02-25

To prepare metal flakes with a high flaking level and investigate the microstructure of metal flakes, nickel and copper powder were mechanically milled in liquid environment and the microstructure of powders was investigated by X-ray diffraction. The milling process can be divided into flaking and broken stages. At the flaking stage, milled metal powders exhibited high flaking level and flaky microshape, and <2 0 0> became preferred orientation. While at the broken stage, the milled powders presented a low flaking level and irregular microshape, and <2 0 0> was not preferred orientation any longer. The grain size, microstrain and dislocation density along <2 0 0> direction varied with milling time differently from that along <1 1 1> direction. The flaking level of the milled powders was related to the <2 0 0> preferred orientation, and more closely to the deformation mechanism. We can strengthen the formation of <2 0 0> preferred orientation to obtain metal powders with a high flaking level.

FePt magnetic particles prepared by surfactant-assisted ball milling

Energy Technology Data Exchange (ETDEWEB)

Velasco, V., E-mail: vvjimeno@fis.ucm.es [Instituto de Magnetismo Aplicado, UCM-ADIF-CSIC, P.O. Box 155, Las Rozas 28230 (Spain); Departamento de Física de Materiales, Universidad Complutense de Madrid, Madrid 28040 (Spain); Hernando, A.; Crespo, P. [Instituto de Magnetismo Aplicado, UCM-ADIF-CSIC, P.O. Box 155, Las Rozas 28230 (Spain); Departamento de Física de Materiales, Universidad Complutense de Madrid, Madrid 28040 (Spain)

2013-10-15

High-energy ball milling of Fe and Pt elemental powders has been carried out under dry and wet (in presence of solvent and surfactants) conditions. Dry milling leads to the formation of the disordered FCC-FePt alloy whereas by the wet milling procedure the main process is the decrease of Fe and Pt particle size, although some dissolution of Pt into Fe grains cannot be ruled out, and no hint of the formation of the FCC-FePt phase is observed even to milling times up to 20 h, as X-ray diffraction, electron microscopy and Mössbauer spectroscopy indicates. The as-milled particles were annealed at 600 °C for 2 h under Ar atmosphere. It is noticed that the disordered fcc-FePt phase observed in particles milled under dry conditions transform to ordered fct phase characterized by a hard magnetic behavior with a coercive field up to 10,000 Oe. However, those particles milled in the surfactant/solvent medium exhibit a soft magnetic behavior with a coercive field of 600 Oe. These results indicate that wet high-energy ball milling is not an adequate technique for obtaining single-phase FePt particles. - Highlights: • FePt particles have been obtained by high-energy ball milling. • In the presence of surfactants and solvents, almost no alloying process takes place. • After annealing, the coercive field of the FePt alloy particles increases from 150 Oe to 10,000 Oe.

High resolution Transmission Electron Microscopy characterization of a milled oxide dispersion strengthened steel powder

Energy Technology Data Exchange (ETDEWEB)

Loyer-Prost, M., E-mail: marie.loyer-prost@cea.fr [DEN-Service de Recherches de Métallurgie Physique, CEA, Université Paris-Saclay, F-91191, Gif-sur-Yvette (France); Merot, J.-S. [Laboratoire d’Etudes des Microstructures – UMR 104, CNRS/ONERA, BP72-29, Avenue de la Division Leclerc, 92 322, Châtillon (France); Ribis, J. [DEN-Service de Recherches de Métallurgie Appliquée, CEA, Université Paris-Saclay, F-91191, Gif-sur-Yvette (France); Le Bouar, Y. [Laboratoire d’Etudes des Microstructures – UMR 104, CNRS/ONERA, BP72-29, Avenue de la Division Leclerc, 92 322, Châtillon (France); Chaffron, L. [DEN-Service de Recherches de Métallurgie Appliquée, CEA, Université Paris-Saclay, F-91191, Gif-sur-Yvette (France); Legendre, F. [DEN-Service de la Corrosion et du Comportement des Matériaux dans leur Environnement, CEA, Université Paris-Saclay, F-91191, Gif-sur-Yvette (France)

2016-10-15

Oxide Dispersion Strengthened (ODS) steels are promising materials for generation IV fuel claddings as their dense nano-oxide dispersion provides good creep and irradiation resistance. Even if they have been studied for years, the formation mechanism of these nano-oxides is still unclear. Here we report for the first time a High Resolution Transmission Electron Microscopy and Energy Filtered Transmission Electron Microscopy characterization of an ODS milled powder. It provides clear evidence of the presence of small crystalline nanoclusters (NCs) enriched in titanium directly after milling. Small NCs (<5 nm) have a crystalline structure and seem partly coherent with the matrix. They have an interplanar spacing close to the (011) {sub bcc} iron structure. They coexist with larger crystalline spherical precipitates of 15–20 nm in size. Their crystalline structure may be metastable as they are not consistent with any Y-Ti-O or Ti-O structure. Such detailed observations in the as-milled grain powder confirm a mechanism of Y, Ti, O dissolution in the ferritic matrix followed by a NC precipitation during the mechanical alloying process of ODS materials. - Highlights: • We observed an ODS ball-milled powder by high resolution transmission microscopy. • The ODS ball-milled powder exhibits a lamellar microstructure. • Small crystalline nanoclusters were detected in the milled ODS powder. • The nanoclusters in the ODS milled powder are enriched in titanium. • Larger NCs of 15–20 nm in size are, at least, partly coherent with the matrix.

Fabrication of Al-20 wt%Si powder using scrap Si by ultra high-energy milling process

Energy Technology Data Exchange (ETDEWEB)

Kang, Won-Kyung [Division of Advanced Materials Engineering and Institute for Rare Metals, Kongju National University, 275, Budae-dong, Cheonan, Chungnam 330-717 (Korea, Republic of); Y Latin-Small-Letter-Dotless-I lmaz, Fikret [Department of Physics, Faculty of Art and Science, Gaziosmanpasa University, Tasliciftlik Campus, 60240 Tokat (Turkey); Kim, Hyo-Seob; Koo, Jar-Myung [Division of Advanced Materials Engineering and Institute for Rare Metals, Kongju National University, 275, Budae-dong, Cheonan, Chungnam 330-717 (Korea, Republic of); Hong, Soon-Jik, E-mail: hongsj@kongju.ac.kr [Division of Advanced Materials Engineering and Institute for Rare Metals, Kongju National University, 275, Budae-dong, Cheonan, Chungnam 330-717 (Korea, Republic of)

2012-09-25

Highlights: Black-Right-Pointing-Pointer High energy ball milling process has been successfully employed to produce Al-20Si alloy using scrap Si powders. Black-Right-Pointing-Pointer Fully finer and homogenous structure could be achieved after 60 min of milling time. Black-Right-Pointing-Pointer Si particles were not dissolved but uniformly dispersed in the Al matrix in a milled state. Black-Right-Pointing-Pointer The hardness of as-milled Al-20Si powder increased steadily with the increase of milling time. Black-Right-Pointing-Pointer Grain size and dispersion strengthening are two mechanisms being responsible for hardness increment. - Abstract: In this study, microstructural evolution and mechanical properties of Al-20 wt%Si and pure Al powders fabricated by ultra high-energy ball milling technique were investigated as a function of milling time. The microstructure and mechanical properties of the as-milled powders were examined by scanning electron microscope (SEM), energy dispersive spectrometry (EDS), X-ray diffractometer (XRD) and Vickers hardness tester. SEM observation showed that the particle size increased at an early stage of milling, and then decreased drastically with further milling. XRD and cross-sectional EDS-mapping analyses revealed that Si particles were not dissolved but uniformly dispersed in the Al matrix in a milled state. Vickers hardness of both pure Al and Al-Si powder increases with milling time, which attributes to the grain size strengthening and dispersion strengthening.

Influence of milling time on microstructure and magnetic properties of Fe{sub 80}P{sub 11}C{sub 9} alloy produced by mechanical alloying

Energy Technology Data Exchange (ETDEWEB)

Taghvaei, A.H. [Department of Materials Science and Engineering, Shiraz University of Technology, Shiraz (Iran, Islamic Republic of); Ghajari, F., E-mail: fati.ghajari@gmail.com [Department of Materials Science and Engineering, Shiraz University, Shiraz (Iran, Islamic Republic of); Markó, D. [IFW Dresden, Institute for Complex Materials, Helmholtzstr. 20, 01069 Dresden (Germany); Prashanth, K.G. [IFW Dresden, Institute for Complex Materials, Helmholtzstr. 20, 01069 Dresden (Germany); Additive manufacturing Center, Sandvik AB, 81181 Sandviken (Sweden)

2015-12-01

Fe{sub 80}P{sub 11}C{sub 9} alloy with amorphous/nanocrytalline microstructure has been synthesized by mechanical alloying of the elemental powders. The microstructure, thermal behavior and morphology of the produced powders have been studied by X-ray diffraction (XRD), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM), respectively. The crystallite size, lattice strain and fraction of the amorphous phase have been calculated by Rietveld refinement method. The results indicate that the powders microstructure consists of α-Fe(P,C) nanocrystals with an average diameter of 9 nm±1 nm dispersed in the amorphous matrix after 90 h of milling. Moreover, the fraction of amorphous phase initially increases up to 90 h of milling and then decreases after 120 h of milling, as a result of mechanical crystallization and formation of Fe{sub 2}P phase. The magnetic measurements show that while the saturation magnetization decreases continuously with the milling time, the coercivity exhibits a complicated trend. The correlation between microstructural changes and magnetic properties has been discussed in detail. - Highlights: • Glass formation was investigated in Fe{sub 80}P{sub 11}C{sub 9} by mechanical alloying. • Structural parameters were calculated by Rietveld refinement method. • Milling first increased and then decreased the fraction of amorphous phase. • Magnetic properties were significantly changed upon milling.

Synthesis of niobium carbide by a high energy milling technique of powder metallurgy

International Nuclear Information System (INIS)

Antonello, Rodrigo Tecchio; Gonzalez, Cezar Henrique; Urtiga Filho, Severino Leopoldino; Araujo Filho, Oscar Olimpio de; Ambrozio Filho, Francisco

2010-01-01

The aim of this work is to obtain and characterize the Niobium Carbide (NbC) by a suitable high energy milling technique using a SPEX Mill vibratory type and niobium and carbon (graphite) powders. Since this carbide is scarced in the national market and it's necessary to apply this NbC as a reinforcement in two molybdenum high speed steels (AISI M2 and AISI M3:2) object of another work motivated this research. The powders were submitted to a high energy milling procedure for suitable times and conditions and then were characterized by means of Scanning Electronic Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and X-ray diffraction (DRX) techniques. The ball-to-powder weight ratio was 10:1. The analysed samples showed that the high-energy milling is an alternative route of the NbC synthesis. (author)

Synthesis of niobium carbide (NbC) by powder metallurgy high energy milling technique

International Nuclear Information System (INIS)

Antonello, Rodrigo Tecchio; Urtiga Filho, Severino Leopoldino; Araujo Filho, Oscar Olimpio de; Ambrozio Filho, Francisco; Gonzalez, Cezar Henrique

2009-01-01

The aim of this work is to obtain and characterize the Niobium Carbide (NbC) by a suitable high energy milling technique using a SPEX Mill vibratory type and niobium and carbon (graphite) powders. Since this carbide is scarce in the national market and it's necessary to apply this NbC as a reinforcement in two molybdenum high speed steels (AISI M2 and AISI M3:2) object of another work motivated this research. The powders were submitted to a high energy milling procedure for suitable times and conditions and then were characterized by means of Scanning Electronic Microscopy (SEM) and X-ray diffraction (DRX) techniques. The ball-to-powder weight ratio was 10:1. The analysed samples showed that the high-energy milling is an alternative route of the NbC synthesis. (author)

Magnetically responsive enzyme powders

Energy Technology Data Exchange (ETDEWEB)

Pospiskova, Kristyna, E-mail: kristyna.pospiskova@upol.cz [Regional Centre of Advanced Technologies and Materials, Palacky University, Slechtitelu 11, 783 71 Olomouc (Czech Republic); Safarik, Ivo, E-mail: ivosaf@yahoo.com [Regional Centre of Advanced Technologies and Materials, Palacky University, Slechtitelu 11, 783 71 Olomouc (Czech Republic); Department of Nanobiotechnology, Institute of Nanobiology and Structural Biology of GCRC, Na Sadkach 7, 370 05 Ceske Budejovice (Czech Republic)

2015-04-15

Powdered enzymes were transformed into their insoluble magnetic derivatives retaining their catalytic activity. Enzyme powders (e.g., trypsin and lipase) were suspended in various liquid media not allowing their solubilization (e.g., saturated ammonium sulfate and highly concentrated polyethylene glycol solutions, ethanol, methanol, 2-propanol) and subsequently cross-linked with glutaraldehyde. Magnetic modification was successfully performed at low temperature in a freezer (−20 °C) using magnetic iron oxides nano- and microparticles prepared by microwave-assisted synthesis from ferrous sulfate. Magnetized cross-linked enzyme powders were stable at least for two months in water suspension without leakage of fixed magnetic particles. Operational stability of magnetically responsive enzymes during eight repeated reaction cycles was generally without loss of enzyme activity. Separation of magnetically modified cross-linked powdered enzymes from reaction mixtures was significantly simplified due to their magnetic properties. - Highlights: • Cross-linked enzyme powders were prepared in various liquid media. • Insoluble enzymes were magnetized using iron oxides particles. • Magnetic iron oxides particles were prepared by microwave-assisted synthesis. • Magnetic modification was performed under low (freezing) temperature. • Cross-linked powdered trypsin and lipase can be used repeatedly for reaction.

The effect of process control agent on the structure and magnetic properties of nanocrystalline mechanically alloyed Fe–45% Ni powders

Energy Technology Data Exchange (ETDEWEB)

Gheisari, Kh., E-mail: khgheisari@scu.ac.ir [Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University, Ahvaz (Iran, Islamic Republic of); Javadpour, S. [Department of Materials Science and Engineering, School of Engineering, Shiraz University, Shiraz (Iran, Islamic Republic of)

2013-10-15

In this study, nanocrystalline Fe-45 wt% Ni alloy powders were prepared by mechanical alloying via high-energy ball milling. The effect of adding stearic acid as a process control agent (PCA) on the particle size, structure and magnetic properties of Fe-45 wt% Ni alloy powders have been studied by X-ray diffraction, scanning electron microscope and vibrating sample magnetometer measurements. The results show that the addition of 1 wt% PCA causes fine uniform spherical powder particles of the fcc γ-(Fe, Ni) phase to be formed after 48 h milling time. It is also found that crystallite size, lattice strain and content of γ-(Fe, Ni) phase are three of the most important variables that are significantly affected by PCA content and can influence the magnetic properties. - Highlights: • Different amount of stearic acid as a PCA was used during milling. • Particle size and crystallite size decrease with increasing PCA content. • The addition of 1 wt% PCA leads to a good combination of structure and magnetic properties.

The effect of process control agent on the structure and magnetic properties of nanocrystalline mechanically alloyed Fe–45% Ni powders

International Nuclear Information System (INIS)

Gheisari, Kh.; Javadpour, S.

2013-01-01

In this study, nanocrystalline Fe-45 wt% Ni alloy powders were prepared by mechanical alloying via high-energy ball milling. The effect of adding stearic acid as a process control agent (PCA) on the particle size, structure and magnetic properties of Fe-45 wt% Ni alloy powders have been studied by X-ray diffraction, scanning electron microscope and vibrating sample magnetometer measurements. The results show that the addition of 1 wt% PCA causes fine uniform spherical powder particles of the fcc γ-(Fe, Ni) phase to be formed after 48 h milling time. It is also found that crystallite size, lattice strain and content of γ-(Fe, Ni) phase are three of the most important variables that are significantly affected by PCA content and can influence the magnetic properties. - Highlights: • Different amount of stearic acid as a PCA was used during milling. • Particle size and crystallite size decrease with increasing PCA content. • The addition of 1 wt% PCA leads to a good combination of structure and magnetic properties

Influence of pin and hammer mill on grinding characteristics, thermal and antioxidant properties of coriander powder.

Science.gov (United States)

Barnwal, P; Singh, K K; Sharma, Alka; Choudhary, A K; Saxena, S N

2015-12-01

In present study, influence of grinding (hammer and pin mills) and moisture content (range: 6.4-13.6 % dry basis) on the quality traits of coriander powder were investigated. These include grinding parameters, colour parameters, specific heat, thermal conductivity, thermal diffusivity, glass transition temperature, essential oil, total phenolic content, total flavonoid content and DPPH scavenging (%) of coriander powder. For coriander seed, the geometric properties such as major, medium, minor dimensions, geometric mean diameter, arithmetic mean diameter, sphericity, surface area and volume of coriander seeds increased significantly with increasing moisture (6.4-13.6 % db). For coriander powder, the grinding parameters such as average particle size, volume surface mean diameter and volume mean diameter increased significantly with increasing moisture (6.4-13.6 % db). With the grinding method, the colour attributes of coriander powder such as L-value, a-value, b-value, hue angle and browning index varied significantly. It was observed that the specific heat followed second order polynomial relationship with temperature and moisture whereas thermal conductivity varied linearly with temperature and moisture content. The variation of glass transition temperature with moisture can be best represented in quadratic manner. Total flavonoid content (mg QE/g crude seed extract) and DPPH scavenging % activity of coriander powder is significantly affected by grinding methods. A lower value of specific heat was observed for hammer ground coriander powder as compared to pin mill ground coriander powder. The thermal conductivity of hammer mill ground coriander powder was higher as compared to pin mill ground coriander. It was observed that hammer mill yields more fine coriander powder in comparison to pin mill. The browning index was more in hammer mill ground coriander powder.

Preparation of 50Ni-45Ti-5Zr powders by high-energy ball milling and hot pressing

Energy Technology Data Exchange (ETDEWEB)

Marinzeck de Alcantara Abdala, Julia, E-mail: juabdala@yahoo.com.b [Instituto de Pesquisa e Desenvolvimento, Universidade do Vale do Paraiba, Av. Shishima Hifumi, 2911, 12244-000 Sao Jose dos Campos (Brazil); Bacci Fernandes, Bruno, E-mail: brunobacci@yahoo.com.b [Divisao de Engenharia Mecanica, Instituto Tecnologico de Aeronautica, Praca Marechal-do-Ar Eduardo Gomes, 50, 12228-904 Sao Jose dos Campos (Brazil); Santos, Dalcy Roberto dos, E-mail: dalcy@iae.cta.b [Instituto de Aeronautica e Espaco, Centro Tecnologico Aeroespacial, Praca Marechal-do-Ar Eduardo Gomes, 50, 12228-904 Sao Jose dos Campos (Brazil); Rodrigues Henriques, Vinicius Andre, E-mail: vinicius@iae.cta.b [Instituto de Aeronautica e Espaco, Centro Tecnologico Aeroespacial, Praca Marechal-do-Ar Eduardo Gomes, 50, 12228-904 Sao Jose dos Campos (Brazil); Moura Neto, Carlos de, E-mail: mneto@ita.b [Divisao de Engenharia Mecanica, Instituto Tecnologico de Aeronautica, Praca Marechal-do-Ar Eduardo Gomes, 50, 12228-904 Sao Jose dos Campos (Brazil); Saraiva Ramos, Alfeu, E-mail: alfeu@univap.b [Instituto de Pesquisa e Desenvolvimento, Universidade do Vale do Paraiba, Av. Shishima Hifumi, 2911, 12244-000 Sao Jose dos Campos (Brazil)

2010-04-16

This study reports on the preparation of the 50Ni-45Ti-5Zr (at.%) alloy by high-energy ball milling and hot pressing. The elemental powder mixture was processed in silicon nitride and hardened steel vials, and samples were collected after different milling times. To recover the previous powders in addition wet milling isopropyl alcohol (for 20 min) was adopted. The mechanically alloyed powders were hot-pressed under vacuum at 900 {sup o}C for 1 h using pressure levels close to 200 MPa. The milled powders were characterized by means of scanning electron microscopy, X-ray diffraction, and energy dispersive spectrometry techniques. It was noted that the ductile starting powders were continuously cold-welded during ball milling. This fact was more pronounced during the processing of 50Ni-45Ti-5Zr powders in hardened steel vial. After milling for 5 h, the results suggested that amorphous and nanocrystalline structures were achieved. The complete consolidation was found after hot pressing of mechanically alloyed 50Ni-45Ti-5Zr powders, and a large amount of the B2-NiTi phase was formed mainly after processing in stainless steel balls and vial.

Anisotropic bonded Sm2.3Fe16.8Zr0.2Ny magnets prepared by milling of as cast material

International Nuclear Information System (INIS)

Gebel, B.; Kubis, M.; Roessler, U.K.; Mueller, K.H.

2001-01-01

As cast Sm 2.3 Fe 16.8 Zr 0.2 material was milled for 100 min ≤ t ≤ 900 min. After annealing at 800 C for 1 h and subsequent nitrogenation, the samples were cold compacted in a magnetic field and resin bonded. The coercivity μ 0J H C of the samples increased from 0.59 T (t = 100 min) to 2.18 T (t = 900 min). On the other hand, the remanence along the texture axis decreased monotonically with increasing milling time due to the decrease of the degree of texture of the aligned powders. Prolonged milling leads finally to the formation of a soft magnetic phase as indicated by a shoulder in the demagnetization curve for t > 600 min. The highest energy product (BH) max of 50 kJm -3 (136 kJm -3 for the theoretical density of 7.7 gcm -3 ) was obtained for an intermediate milling time of 400 min. Zn bonding of the powders resulted in magnets with lower energy products but improved coercivities. (orig.)

An investigation on the compressibility of aluminum/nano-alumina composite powder prepared by blending and mechanical milling

International Nuclear Information System (INIS)

Razavi Hesabi, Z.; Hafizpour, H.R.; Simchi, A.

2007-01-01

The densification response of aluminum powder reinforced with 5 vol.% nanometric alumina particles (35 nm) during uniaxial compaction in a rigid die was studied. The composite powder was prepared by blending and mechanical milling procedures. To determine the effect of the reinforcement nanoparticles on the compressibility of aluminum powder, monolithic Al powder, i.e. without the addition of alumina, was also examined. It was shown that at the early stage of compaction when the rearrangement of particles is the dominant mechanism of the densification, disintegration of the nanoparticle clusters and agglomerates under the applied load contributes in the densification of the composite powder prepared by blending method. As the compaction pressure increases, however, the load partitioning effect of the nanoparticles decreases the densification rate of the powder mixture, resulting in a lower density compared to the monolithic aluminum. It was also shown that mechanical milling significantly impacts the compressibility of the unreinforced and reinforced aluminum powders. Morphological changes of the particles upon milling increase the contribution of particle rearrangement in densification whilst the plastic deformation mechanism is significantly retarded due to the work-hardening effect of the milling process. Meanwhile, the distribution of alumina nanoparticles is improved by mechanical milling, which in fact, affects the compressibility of the composite powder. This paper addresses the effect of mechanical milling and reinforcement nanoparticles on the compressibility of aluminum powder

Attritor milling of WC + 6% Co: Effects on powder characteristics and compaction behavior

International Nuclear Information System (INIS)

Mashl, S.J.; Smith, D.W.; Becking, G.H.; Hale, T.E.

1987-01-01

This study examines the effects of attritor milling on the characteristics and bulk behavior of fine tungsten carbide powders (initial median particle size ≅ 1.5 μm) blended with 6 wt. % cobalt (mps ≅ 1.5 μm). Experiments are performed in order to: Develop a process model relating the specific energy input to the milled median particle size. Examine the effect that changes in milling variables have on the specific energy - median particle size relationship. Observe the effects of variation in the initial particle size distribution on the as-milled particle size distribution, the compaction characteristics of the powder, and the shrinkage which will occur during sintering. The process model is based on Charles' equation, E-bar = A (d/sup -α/ - d/sub o//sup -α/) in which E-bar = the specific energy consumed in milling, d and d = the initial and milled median particle sizes respectively, and A and α are constants. Computer curve fitting techniques are employed to determine the values of the coefficient and exponent in the above equation. The resulting model predicts the experimental data within about +- over 10% over a significant range of d/sub o/ and E-Bar values. The apparent density and compactibility of the attritor milled powders are observed to be very sensitive to the milled particle size distribution

Alloying and microstructural changes in platinum–titanium milled and annealed powders

International Nuclear Information System (INIS)

Maweja, Kasonde; Phasha, M.J.; Yamabe-Mitarai, Y.

2012-01-01

Graphical abstract: (a) SE-SEM micrographs of PtTi martensite formed in powder milled for short time annealed at 1500 °C and quenched in helium gas flow (b) BSE-SEM of structure formed after slow cooling. Highlights: ► A disordered metastable FCC Pt(Ti) solid solution was formed after longer milling period. ► HCP Ti crystals were first deformed and then the atoms were dissolved in strained FCC Pt lattices. ► Longer milling time suppressed the occurrence of martensitic transformation after annealing. ► Martensite phase was formed in products that went through a short milling time then annealed and quenched. ► The width of the martensite features formed was smaller at higher cooling rates. - Abstract: Equiatomic platinum–titanium powder mixtures were processed by high energy ball milling under argon atmosphere and sintered under vacuum. Evolution of the crystal structures and microstructures of the products formed were investigated by XRD and SEM techniques, respectively. The HCP crystals of Ti were first deformed and then a disordered metastable FCC Pt(Ti) solid solution was formed during milling due to semi-coherency of FCC lattices. A nanostructured Pt(Ti) product was formed after long milling time, which contained 44–47 at.% Ti and 53–56 at.% Pt. An ordered PtTi intermetallic was formed by annealing the metastable Pt(Ti) at temperature above 1300 °C. The crystal structure and microstructure of the TiPt phase depended on the milling time, annealing temperature and the cooling rate. The B19 PtTi plate martensite was formed after annealing at 1500 °C and quenching at a cooling rate of 23 °C/min to 200 °C/min for short time milled products. The width of martensite features was smaller at high cooling rate. In PtTi products milled for longer time, no martensitic transformation was observed on cooling the annealed samples. Small amounts of Pt 5 Ti 3 were formed in the powders milled for 16 h or more, followed by annealing at 1500 °C and furnace

Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al₂O₃ Nanocomposite Synthesized by Ball Milling and Powder Metallurgy.

Science.gov (United States)

Toozandehjani, Meysam; Matori, Khamirul Amin; Ostovan, Farhad; Abdul Aziz, Sidek; Mamat, Md Shuhazlly

2017-10-26

The effect of milling time on the morphology, microstructure, physical and mechanical properties of pure Al-5 wt % Al₂O₃ (Al-5Al₂O₃) has been investigated. Al-5Al₂O₃ nanocomposites were fabricated using ball milling in a powder metallurgy route. The increase in the milling time resulted in the homogenous dispersion of 5 wt % Al₂O₃ nanoparticles, the reduction of particle clustering, and the reduction of distances between the composite particles. The significant grain refining during milling was revealed which showed as a reduction of particle size resulting from longer milling time. X-Ray diffraction (XRD) analysis of the nanocomposite powders also showed that designated ball milling contributes to the crystalline refining and accumulation of internal stress due to induced severe plastic deformation of the particles. It can be argued that these morphological and microstructural variations of nanocomposite powders induced by designated ball milling time was found to contribute to an improvement in the density, densification, micro-hardness ( HV ), nano-hardness ( HN ), and Young's modulus ( E ) of Al-5Al₂O₃ nanocomposites. HV , HN , and E values of nanocomposites were increased by ~48%, 46%, and 40%, after 12 h of milling, respectively.

Influence of the milling time in the microstructural parameters of TA2O5-Al powder refined by Rietveld method

International Nuclear Information System (INIS)

Brito, R.A.; Mendes, M.W.D.; Alves Junior, C.; Costa, F.A. da; Gomes, U.U.

2009-01-01

Mechanical alloying (MA) is a solid-state powder processing technique involving repeated welding, fracturing, and re-welding of powder particles in a high energy mill. This process is used for producing of fine powders containing unique microstructures. The process starts with mixing of the powders in the desired proportion. Then, the mixture is milled using the established time in the high-energy mill. The powder particles are submitted to repeated cycles of cold working and fracture, and the final product correspond to a composite powder, containing characteristics different of the initial constituents. Ta 2 O 5 -Al powders were milled in a planetary ball mill for different times in order to evaluate the influence of the milling time in their microstructural parameters like crystallite size and micro deformation. The microstructural parameters were obtained by the Rietveld Method. The results showed that the microstructural parameters were influenced by the increase of the milling time. (author)

Effect of milling variables on powder character and sintering behaviour of 434L ferritic stainless steel-Al2O3 composites

International Nuclear Information System (INIS)

Mukherjee, S.K.; Upadhyaya, G.S.

1985-01-01

Ball milling of ferritic stainless steel-4 vol% Al 2 O 3 powder was carried out for the duration up to 222 ks. Attritor milling of ferritic stainless steel-6 vol% Al 2 O 3 were also carried out for the duration up to 32.4 ks. The characterization of the milled powders were performed. The sintering of ball milled powders was carried out at 1623 K for 10.8 ks in hydrogen. The premix of as received stainless steel powder and the attritor milled powder was also sintered at 1623 K for 3.6 ks in hydrogen. The results showed that an optimum ball milling period in between 58 and 173 ks was required to achieve better sintered properties. The attritor milling was more effective in grinding the powders as compared to ball milling, and the sinterability was also higher for such powders. (author)

Consolidation of mechanically milled powder mixture of aluminum and quasicrystalline particle; Mechanical milling shita junkessho ryushi / aluminium gokin funmatsu no koka seikeisei

Energy Technology Data Exchange (ETDEWEB)

Yuasa, E.; Kawamura, C.; Sugiyama, T. [Musashi Institute of Technology, Tokyo (Japan)

1998-10-15

A quasi-crystalline Al65Cu20Fe15 powder prepared from alloy cast rapidly solidified by metal-mold casting, and then it was mixed to aluminum powder with various volume fractions by mechanical milling. The powder milled for above 50ks made homogeneous dispersion of quasi-crystalline phase with particle size less than 1{mu}m. The powder was hot-pressed under various conditions and then its features of consolidation were examined by the observation of microstructure and fracture strength in 3-point-bending of the compacts. When the milled powder was hot-pressed at higher compacting temperature than 673K for 3.6ks under pressure of 600MPa, the compact became to dense. Hardness of the obtained compact increases and its fracture strength decreases with increasing volume fraction of quasi-crystalline particles. Intermetallic compound Al7Cu2Fe forms in the interface of aluminum matrix and quasi-crystalline particle. 11 refs., 10 figs.

Effect of ball milling and dynamic compaction on magnetic properties of Al{sub 2}O{sub 3}/Co(P) composite particles

Energy Technology Data Exchange (ETDEWEB)

Denisova, E. A. [Kirensky Institute of Physics SB RAS, Krasnoyarsk (Russian Federation); Krasnoyarsk Institute of Railways Transport, Krasnoyarsk (Russian Federation); Kuzovnikova, L. A. [Krasnoyarsk Institute of Railways Transport, Krasnoyarsk (Russian Federation); Iskhakov, R. S., E-mail: rauf@iph.krasn.ru; Eremin, E. V. [Kirensky Institute of Physics SB RAS, Krasnoyarsk (Russian Federation); Bukaemskiy, A. A. [Institut fur Sicherheitsforschung und Reaktortechnik, D-52425 Juelich (Germany); Nemtsev, I. V. [Krasnoyarsk Scientific Center SB RAS, Krasnoyarsk (Russian Federation)

2014-05-07

The evolution of the magnetic properties of composite Al{sub 2}O{sub 3}/Co(P) particles during ball milling and dynamic compaction is investigated. To prepare starting composite particles, the Al{sub 2}O{sub 3} granules were coated with a Co{sub 95}P{sub 5} shell by electroless plating. The magnetic and structural properties of the composite particles are characterized by scanning electron microscopy, X-ray diffraction, and the use of the Physical Property Measurement System. The use of composite core-shell particles as starting powder for mechanoactivation allows to decrease treatment duration to 1 h and to produce a more homogeneous bulk sample than in the case of the mixture of Co and Al{sub 2}O{sub 3} powders. The magnetic properties of the milled composite particles are correlated with changes in the microstructure. Reduction in grain size of Co during milling leads to an increase of the volume fraction of superparamagnetic particles and to a decrease of the saturation magnetization. The local magnetic anisotropy field depends on the amount of hcp-Co phase in sample. The anisotropy field value decreases from 8.4 kOe to 3.8 kOe with an increase in milling duration up to 75 min. The regimes of dynamic compaction were selected so that the magnetic characteristics—saturation magnetization and coercive field—remained unchanged.

Comprehensive characterization of ball-milled powders simulating a tribofilm system

Energy Technology Data Exchange (ETDEWEB)

Häusler, I., E-mail: ines.haeusler@bam.de; Dörfel, I., E-mail: Ilona.doerfel@bam.de; Peplinski, B., E-mail: Burkhard.peplinski@bam.de; Dietrich, P.M., E-mail: Paul.dietrich@yahoo.de; Unger, W.E.S., E-mail: Wolfgang.Unger@bam.de; Österle, W., E-mail: Werner.Oesterle@bam.de

2016-01-15

A model system was used to simulate the properties of tribofilms which form during automotive braking. The model system was prepared by ball milling of a blend of 70 vol.% iron oxides, 15 vol.% molybdenum disulfide and 15 vol.% graphite. The resulting mixture was characterized by X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and various transmission electron microscopic (TEM) methods, including energy dispersive X-ray spectroscopy (EDXS), high resolution investigations (HRTEM) with corresponding simulation of the HRTEM images, diffraction methods such as scanning nano-beam electron diffraction (SNBED) and selected area electron diffraction (SAED). It could be shown that the ball milling caused a reduction of the grain size of the initial components to the nanometer range. Sometimes even amorphization or partial break-down of the crystal structure was observed for MoS{sub 2} and graphite. Moreover, chemical reactions lead to a formation of surface coverings of the nanoparticles by amorphous material, molybdenum oxides, and iron sulfates as derived from XPS. - Highlights: • Ball milling of iron oxides, MoS{sub 2}, and graphite to simulate a tribofilm • Increasing coefficient of friction after ball milling of the model blend • Drastically change of the diffraction pattern of the powder mixture • TEM & XPS showed the components of the milled mixture and the process during milling. • MoS{sub 2} and graphite suffered a loss in translation symmetry or became amorphous.

Simplification of the processing of milled aluminium powder and mechanical evaluation properties

International Nuclear Information System (INIS)

Cintas, J.; Rodriguez, J. A.; Gallardo, J. M.; Herrera, E. J.

2001-01-01

An alternative powder.metallurgy consolidation method of milled aluminium (M Al) powder, consisting in a double cycle of cold pressing and vacuum sintering, has been developed. The aim of the present investigation is to simplify this consolidation method, from the original five steps to only three steps. This would be possible since milled powders soften during desassing, at high temperature. The mechanical properties of compacts (hardness at room and high temperature, ultimate tensile strength and elongation) obtained by the three-step and the five-step processing are comparable. This process could be ol special interest for the manufacturing of large series of small parts, such as are used in the automotive industry. (Author) 10 refs

Moessbauer analysis of high-energy mechanical-milled sand fraction of a magnetic soil developing on basalt

Energy Technology Data Exchange (ETDEWEB)

Borges, Jose Flavio Marcelino; Hneda, Marlon Luiz; Brinatti, Andre Mauricio [State University of Ponta Grossa, Department of Physics (Brazil); Cunha, Joao Batista Marimon da [Federal University of Rio Grande do Sul, Institute of Physics (Brazil); Rosa, Jadir Aparecido [Polo Regional de Ponta Grossa, Agronomy Institute of Parana (Brazil); Fabris, Jose Domingos, E-mail: jdfabris@ufmg.br [Federal University of Jequitinhonha and Mucuri Valleys (UFVJM) (Brazil)

2011-11-15

A sample of the coarse sand fraction from the soil material of the A-horizon (0-0.2 m from the soil surface) of a dusky red magnetic Oxisol was submitted to high-energy mechanical milling for different times. This assay aimed mainly at (a) monitoring the individualization of strongly aggregated mineral particles, and (b) measuring the effect of the milling pressure on the mineralogy changes of the material. These data are also intended to experimentally subside any physical model describing the mechanical behavior of the superficial soil layer that is subjected to intensive machine management, in agriculture fields. Powder X-ray data reveal that some mineralogical phases, notably gibbsite, disappear soon after the first few hours milling. The 298 K-transmission Moessbauer spectrum for the non-milled sand sample shows a qualitatively typical pattern for the sand fraction of basalt derived soils, with magnetically ordered sextets, assignable mainly to hematite and maghemite, and an intense central (super)paramagnetic Fe{sup 3 + } doublet. For the milled samples, spectra revealed progressive spectral reduction of the magnetic hyperfine structure, with concomitant increase of relative subspectral areas due to (super)paramagnetic phases, as the milling time increased. This result is consistent with the reduction of measured saturation magnetization, from 4.96(8) J T{sup - 1} kg{sup - 1}, for the non-milled sample, to 3.26(7) J T{sup - 1} kg{sup - 1}, for the sample milled for 8 hours.

Hysteresis losses of magnetic nanoparticle powders in the single domain size range

International Nuclear Information System (INIS)

Dutz, S.; Hergt, R.; Muerbe, J.; Mueller, R.; Zeisberger, M.; Andrae, W.; Toepfer, J.; Bellemann, M.E.

2007-01-01

Magnetic iron oxide nanoparticle powders were investigated in order to optimise the specific hysteresis losses for biomedical heating applications. Different samples with a mean particle size in the transition range from superparamagnetic to ferromagnetic behaviour (i.e. 10-100 nm) were prepared by two different chemical precipitation routes. Additionally, the influence of milling and annealing on hysteresis losses of the nanoparticles was investigated. Structural investigations of the samples were carried out by X-ray diffraction, measurement of specific surface area, and scanning and transmission electron microscopy. The dependence of hysteresis losses of minor loops on the field amplitude was determined using vibrating sample magnetometry and caloric measurements. For small field amplitudes, a power law was found which changes into saturation at amplitudes well above the coercive field. Maximum hysteresis losses of 6.6 J/kg per cycle were observed for milled powder. For field amplitudes below about 10 kA/m, which are especially interesting for medical and technical applications, hysteresis losses of all investigated powders were at least by one order of magnitude lower than reported for magnetosomes of comparable size

Fabrication of Biochips with Micro Fluidic Channels by Micro End-milling and Powder Blasting

Directory of Open Access Journals (Sweden)

Dong Sam Park

2008-02-01

Full Text Available For microfabrications of biochips with micro fluidic channels, a large number of microfabrication techniques based on silicon or glass-based Micro-Electro-Mechanical System (MEMS technologies were proposed in the last decade. In recent years, for low cost and mass production, polymer-based microfabrication techniques by microinjection molding and micro hot embossing have been proposed. These techniques, which require a proper photoresist, mask, UV light exposure, developing, and electroplating as a preprocess, are considered to have some problems. In this study, we propose a new microfabrication technology which consists of micro end-milling and powder blasting. This technique could be directly applied to fabricate the metal mold without any preprocesses. The metal mold with micro-channels is machined by micro end-milling, and then, burrs generated in the end-milling process are removed by powder blasting. From the experimental results, micro end-milling combined with powder blasting could be applied effectively for fabrication of the injection mold of biochips with micro fluidic channels.

Magnetic characterization of nanocrystalline Fe80−xCrxCo20 (15≤x≤35) alloys during milling and subsequent annealing

International Nuclear Information System (INIS)

Rastabi, Reza Amini; Ghasemi, Ali; Tavoosi, Majid; Sodaee, Tahmineh

2016-01-01

Magnetic characterization of nanocrystalline Fe–Cr–Co alloys during milling and annealing process was the goal of this study. To formation of Fe 80−x Cr x Co 20 (15≤x≤35) solid solution, different powder mixtures of Fe, Cr and Co elements were mechanically milled in a planetary ball mill. The annealing process was done in as-milled samples at different temperature in the range of 500–640 °C for 2 h. The produced samples were characterized using X-ray diffraction, scanning electron microscopy, differential scanning calorimetry and vibrating sample magnetometer. Performed mechanical alloying in different powder mixtures lead to the formation of Fe–Cr–Co α-phase solid solution with average crystallite sizes of about 10 nm. The produced nanocrystalline alloys exhibit magnetic properties with the coercivity and saturation of magnetization in the range of 110–200 Oe and 150–220 emu/g, respectively. The coercivity of produced alloys after annealing process decreased and reached to about 40–150 Oe. The highest value of coercivity in as-milled and annealed samples was achieved in alloys with higher Cr contents. - Highlights: • Hc and Ms of produced alloys obtained in the range of 110–200 Oe and 150–220 emu/g. • The highest value of Hc in milled and annealed samples was achieved in Fe 45 Cr 35 Co 20 . • Hc of produced alloys after spinodal decomposition decreased to about 40–150 Oe. • The effect of crystalline defects and residual strain on magnetic fields pinning in milled samples is higher than spinodal decomposition in annealed samples. • The highest value of Hc in as-milled and annealed samples was achieved in Fe 45 Cr 35 Co 20 . The coercivity of produced alloys after annealing process decreased and reach to about 40–150 Oe. • The produced nanocrystalline alloys exhibit magnetic properties with the coercivity and saturation of magnetization in the range of 110–200 Oe and 150–220 emu/g, respectively.

The effect of intermediate stop and ball size in fabrication of recycled steel powder using ball milling from machining steel chips

International Nuclear Information System (INIS)

Fitri, M.W.M.; Shun, C.H.; Rizam, S.S.; Shamsul, J.B.

2007-01-01

A feasibility study for producing recycled steel powder from steel scrap by ball milling was carried out. Steel scrap from machining was used as a raw material and was milled using planetary ball milling. Three samples were prepared in order to study the effect of intermediate stop and ball size. Sample with intermediate stop during milling process showed finer particle size compared to the sample with continuous milling. Decrease in the temperature of the vial during the intermediate stop milling gives less ductile behaviour to the steel powder, which is then easily work-hardened and fragmented to fine powder. Mixed small and big size ball give the best production of recycled steel powder where it gives higher impact force to the scrap and accelerate the fragmentation of the steel scrap into powder. (author)

Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al2O3 Nanocomposite Synthesized by Ball Milling and Powder Metallurgy

Science.gov (United States)

Matori, Khamirul Amin; Ostovan, Farhad; Abdul Aziz, Sidek; Mamat, Md Shuhazlly

2017-01-01

The effect of milling time on the morphology, microstructure, physical and mechanical properties of pure Al-5 wt % Al2O3 (Al-5Al2O3) has been investigated. Al-5Al2O3 nanocomposites were fabricated using ball milling in a powder metallurgy route. The increase in the milling time resulted in the homogenous dispersion of 5 wt % Al2O3 nanoparticles, the reduction of particle clustering, and the reduction of distances between the composite particles. The significant grain refining during milling was revealed which showed as a reduction of particle size resulting from longer milling time. X-Ray diffraction (XRD) analysis of the nanocomposite powders also showed that designated ball milling contributes to the crystalline refining and accumulation of internal stress due to induced severe plastic deformation of the particles. It can be argued that these morphological and microstructural variations of nanocomposite powders induced by designated ball milling time was found to contribute to an improvement in the density, densification, micro-hardness (HV), nano-hardness (HN), and Young’s modulus (E) of Al-5Al2O3 nanocomposites. HV, HN, and E values of nanocomposites were increased by ~48%, 46%, and 40%, after 12 h of milling, respectively. PMID:29072632

Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al2O3 Nanocomposite Synthesized by Ball Milling and Powder Metallurgy

Directory of Open Access Journals (Sweden)

Meysam Toozandehjani

2017-10-01

Full Text Available The effect of milling time on the morphology, microstructure, physical and mechanical properties of pure Al-5 wt % Al2O3 (Al-5Al2O3 has been investigated. Al-5Al2O3 nanocomposites were fabricated using ball milling in a powder metallurgy route. The increase in the milling time resulted in the homogenous dispersion of 5 wt % Al2O3 nanoparticles, the reduction of particle clustering, and the reduction of distances between the composite particles. The significant grain refining during milling was revealed which showed as a reduction of particle size resulting from longer milling time. X-Ray diffraction (XRD analysis of the nanocomposite powders also showed that designated ball milling contributes to the crystalline refining and accumulation of internal stress due to induced severe plastic deformation of the particles. It can be argued that these morphological and microstructural variations of nanocomposite powders induced by designated ball milling time was found to contribute to an improvement in the density, densification, micro-hardness (HV, nano-hardness (HN, and Young’s modulus (E of Al-5Al2O3 nanocomposites. HV, HN, and E values of nanocomposites were increased by ~48%, 46%, and 40%, after 12 h of milling, respectively.

Anisotropic bonded Sm{sub 2.3}Fe{sub 16.8}Zr{sub 0.2}N{sub y} magnets prepared by milling of as cast material

Energy Technology Data Exchange (ETDEWEB)

Gebel, B.; Kubis, M.; Roessler, U.K.; Mueller, K.H. [Institut fuer Festkoerper- und Werkstofforschung Dresden e.V. (Germany). Inst. fuer Metallische Werkstoffe

2001-07-01

As cast Sm{sub 2.3}Fe{sub 16.8}Zr{sub 0.2} material was milled for 100 min {<=} t {<=} 900 min. After annealing at 800 C for 1 h and subsequent nitrogenation, the samples were cold compacted in a magnetic field and resin bonded. The coercivity {mu}{sub 0J}H{sub C} of the samples increased from 0.59 T (t = 100 min) to 2.18 T (t = 900 min). On the other hand, the remanence along the texture axis decreased monotonically with increasing milling time due to the decrease of the degree of texture of the aligned powders. Prolonged milling leads finally to the formation of a soft magnetic phase as indicated by a shoulder in the demagnetization curve for t > 600 min. The highest energy product (BH){sub max} of 50 kJm{sup -3} (136 kJm{sup -3} for the theoretical density of 7.7 gcm{sup -3}) was obtained for an intermediate milling time of 400 min. Zn bonding of the powders resulted in magnets with lower energy products but improved coercivities. (orig.)

Sintered Fe-Ni-Cu-Sn-C Alloys Made of Ball-Milled Powders

Directory of Open Access Journals (Sweden)

Romański A.

2014-10-01

Full Text Available The main objective of this paper was to perform sinterability studies of ball-milled Fe-12%Ni-6.4%Cu-1.6%Sn-0.6%C powders. A mixture of precisely weighed amounts of elemental iron, nickel and graphite, and pre-alloyed 80/20 bronze powders was ball-milled for 8, 30 and 120 hours. After cold-pressing at 400 MPa the specimens were sintered at 900oC for 30 minutes in a reducing atmosphere and subsequently tested for density and hardness as well as subjected to structural studies using scanning electron microscopy (SEM and X-ray diffraction (XRD analysis.

Powder production of U-Mo alloy, HMD process (Hydriding- Milling- Dehydriding)

Energy Technology Data Exchange (ETDEWEB)

Pasqualini, E. E.; Garcia, J.H.; Lopez, M.; Cabanillas, E.; Adelfang, P. [Dept. Combustibles Nucleares. Comision Nacional de Energia Atomica, Av. Gral. Paz 1499, 1650 Buenos Aires (Argentina)

2002-07-01

Uranium-molybdenum (U-Mo) alloys can be hydrided massively in metastable {gamma} (gamma) phase. The brittle hydride can be milled and dehydrided to acquire the desired size distributions needed for dispersion nuclear fuels. The developments of the different steps of this process called hydriding-milling- dehydriding (HMD Process) are described. Powder production scales for industrial fabrication is easily achieved with conventional equipment, small man-power and low investment. (author)

Powder production of U-Mo alloy, HMD process (Hydriding- Milling- Dehydriding)

International Nuclear Information System (INIS)

Pasqualini, E. E.; Garcia, J.H.; Lopez, M.; Cabanillas, E.; Adelfang, P.

2002-01-01

Uranium-molybdenum (U-Mo) alloys can be hydrided massively in metastable γ (gamma) phase. The brittle hydride can be milled and dehydrided to acquire the desired size distributions needed for dispersion nuclear fuels. The developments of the different steps of this process called hydriding-milling- dehydriding (HMD Process) are described. Powder production scales for industrial fabrication is easily achieved with conventional equipment, small man-power and low investment. (author)

Solid-state reactions to synthesize nanostructured lead selenide semiconductor powders by high-energy milling

Energy Technology Data Exchange (ETDEWEB)

Rojas-Chavez, H., E-mail: uu_gg_oo@yahoo.com.mx [Centro de Investigacion e Innovacion Tecnologica - IPN, Cerrada de CECATI s/n, Col. Santa Catarina, Del. Azcapotzalco (Mexico) and Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada - IPN, Legaria 694, Col. Irrigacion, Del. Miguel Hidalgo (Mexico); Reyes-Carmona, F. [Facultad de Quimica - UNAM, Circuito de la Investigacion Cientifica s/n, C.U. Del. Coyoacan (Mexico); Jaramillo-Vigueras, D. [Centro de Investigacion e Innovacion Tecnologica - IPN, Cerrada de CECATI s/n, Col. Santa Catarina, Del. Azcapotzalco (Mexico)

2011-10-15

Highlights: {yields} PbSe synthesized from PbO instead of Pb powder do not require an inert atmosphere. {yields} During high-energy milling oxygen has to be chemically reduced from the lead oxide. {yields} Solid-state and solid-gas chemical reactions promote both solid and gaseous products. -- Abstract: Both solid-solid and gas-solid reactions have been traced during high-energy milling of Se and PbO powders under vial (P, T) conditions in order to synthesize the PbSe phase. Chemical and thermodynamic arguments are postulated to discern the high-energy milling mechanism to transform PbO-Se micropowders onto PbSe-nanocrystals. A set of reactions were evaluated at around room temperature. Therefore an experimental campaign was designed to test the nature of reactions in the PbO-Se system during high-energy milling.

Solid-state reactions to synthesize nanostructured lead selenide semiconductor powders by high-energy milling

International Nuclear Information System (INIS)

Rojas-Chavez, H.; Reyes-Carmona, F.; Jaramillo-Vigueras, D.

2011-01-01

Highlights: → PbSe synthesized from PbO instead of Pb powder do not require an inert atmosphere. → During high-energy milling oxygen has to be chemically reduced from the lead oxide. → Solid-state and solid-gas chemical reactions promote both solid and gaseous products. -- Abstract: Both solid-solid and gas-solid reactions have been traced during high-energy milling of Se and PbO powders under vial (P, T) conditions in order to synthesize the PbSe phase. Chemical and thermodynamic arguments are postulated to discern the high-energy milling mechanism to transform PbO-Se micropowders onto PbSe-nanocrystals. A set of reactions were evaluated at around room temperature. Therefore an experimental campaign was designed to test the nature of reactions in the PbO-Se system during high-energy milling.

Synthesis and characterization of high volume fraction Al-Al2O3 nanocomposite powders by high-energy milling

International Nuclear Information System (INIS)

Prabhu, B.; Suryanarayana, C.; An, L.; Vaidyanathan, R.

2006-01-01

Al-Al 2 O 3 metal matrix composite (MMC) powders with volume fractions of 20, 30, and 50% Al 2 O 3 were synthesized by high-energy milling of the blended component powders. The particle sizes of Al 2 O 3 studied were 50 nm, 150 nm, and 5 μm. A uniform distribution of the Al 2 O 3 reinforcement in the Al matrix was successfully obtained after milling the powders for a period of 20 h at a ball-to-powder ratio of 10:1 in a SPEX mill. The uniform distribution of Al 2 O 3 in the Al matrix was confirmed by characterizing these nanocomposite powders by scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), X-ray mapping, and X-ray diffraction (XRD) techniques

Characterisation of Mn0.63Zn0.37Fe2O4 powders after intensive milling and subsequent thermal treatment

Directory of Open Access Journals (Sweden)

Labus Nebojša

2017-01-01

Full Text Available Commercial Mn-Zn powder (Mn0.63Zn0.37Fe2O4, 93 wt. % and Fe2O3 7 wt. % was milled 0.5, 1, 2 and 4 hours in a planetary ball mill. The goal was to observe intensive milling influences on oxidation and reduction processes that will happen during subsequent heating. Powders were characterized with XRD, SEM and particle seizer. Subsequent heating was monitored on TGA/DTA in an air atmosphere. After compaction of the milled powders, sintering was also performed in a dilatometric device. Sintered specimens were characterized micro structurally with SEM on a fresh breakage. Obtained differential TGA diagrams suggest intensive changes during prolonged milling of the oxidation kinetics on heating. Ferrite powders changed with milling as well as with second run heating were characterized to enable determination of the potentially best ratio of milling and heating to be applied to obtain the desired microstructure. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. OI172057 and Grant no. III45014

In situ Fabrication of Fe-TiB{sub 2} Nanocomposite Powder by Planetary Ball Milling and Subsequent Heat-treatment of FeB and TiH{sub 2} Powder Mixture

Energy Technology Data Exchange (ETDEWEB)

Huynh, Xuan-Khoa [Hanoi Uneversity of Science and Technology, Hanoi (Viet Nam); Bae, Sun-Woo; Kim, Ji Soon [University of Ulsan, Ulsan (Korea, Republic of)

2017-01-15

Fe-TiB{sub 2} powder was synthesized in-situ by the planetary ball milling and subsequent heat-treatment of an iron boride (FeB) and titanium hydride (TiH{sub 2}) powder mixture. Mechanical activation of the (FeB+TiH{sub 2}) powder mixtures was observed after a milling time of 3 hours at 700 rpm of rotation speed, but activation was not the same after 1 hour milling time. The particle size of the (FeB+ TiH{sub 2}) powder mixture was reduced to the nanometer scale, and each constituent was homogeneously distributed. A sharp exothermic peak was observed at a lower temperature (749 ℃) on the DSC curves for the (FeB+TiH{sub 2}) powder mixture milled for 3 hours, compared to the one milled for 1 hour (774 ℃). These peaks were confirmed to have resulted from the formation reaction of the TiB{sub 2} phase, from Ti and B elements in the FeB. The Fe-TiB{sub 2} composite powder fabricated in situ exhibited only two phases of Fe and TiB{sub 2} with homogeneous distribution. The size of the TiB{sub 2} particulates in the Fe matrix was less than 5 nm.

Preparation and soft magnetic properties of spark plasma sintered compacts based on Fe–Si–B glassy powder

Energy Technology Data Exchange (ETDEWEB)

Neamţu, B.V., E-mail: bogdan.neamtu@stm.utcluj.ro [Materials Science and Engineering Department, Technical University of Cluj-Napoca, 400614 Cluj-Napoca (Romania); Marinca, T.F.; Chicinaş, I. [Materials Science and Engineering Department, Technical University of Cluj-Napoca, 400614 Cluj-Napoca (Romania); Isnard, O. [Institut Néel, CNRS/University Joseph Fourier, BP 166, 38042 Grenoble Cédex 9 (France); Popa, F. [Materials Science and Engineering Department, Technical University of Cluj-Napoca, 400614 Cluj-Napoca (Romania); Păşcuţă, P. [Physics and Chemistry Department Technical University of Cluj-Napoca, 400614 Cluj-Napoca (Romania)

2014-07-05

Highlights: • Amorphous powder of Fe{sub 75}Si{sub 20}B{sub 5} (at.%) was prepared by wet mechanical alloying. • Spark plasma sintering was used for compaction of amorphous Fe{sub 75}Si{sub 20}B{sub 5} powder. • Increasing SPS time/temperature leads to improvement of AC/DC compacts properties. - Abstract: Amorphous powder of Fe{sub 75}Si{sub 20}B{sub 5} (at.%) was prepared by wet mechanical alloying route using benzene as surfactant. The amorphous phase is obtained after 60 h of milling. Structural, morphological, and thermal characteristics were investigated. The as-milled powder consists in micrometric particles with a mean diameter of 10.4 μm which are formed by the agglomeration of smaller particles. The amorphous powder is thermally stable up to the temperature of 490 °C. Spark plasma sintered compacts were prepared from the amorphous powders at sintering temperatures of 800, 850 and 900 °C. The phases formation and their evolution was investigated by X-ray diffraction technique showing that Fe{sub 3}Si and Fe{sub 2}B are the main phases formed during the spark plasma sintering process. Fe{sub 75}Si{sub 20}B{sub 5} (at.%) samples in the form of a ring were investigated in DC and AC magnetization regime. It was found that the boride phase formation (during sintering) and the low density of the compacts affect the magnetic properties of the compacts. In addition, a superficial contamination of the compacts with carbon (a layer of 2–3 μm) was evidenced, contributing thus to their soft magnetic deterioration. Increasing of the saturation induction, maximum relative permeability and initial relative permeability was observed by increasing both sintering temperature and time. It was generally observed that the compacts with high density have higher total core losses at high frequency.

Analysis of the influence of two different milling processes in the properties of precursor powder and [Beta]-TCP cement

International Nuclear Information System (INIS)

Cardoso, H.A.I.; Pereira, C.H.R.; Zavaglia, C.A.C.; Motisuke, M.

2011-01-01

There are several characteristics that put calcium phosphate cements in evidence, like its bioactivity and in vivo resorption. The influence of two milling processes in the morphological properties of the [beta]-tricalcium phosphate powder, [beta]-TCP, and in the mechanical properties of the cement were analyzed. The powder was obtained by solid state reaction of CaCO_3 and CaHPO_4 at 1050 ° C. It showed high phase purity and absence of toxic elements. The powder was processed in ball mill (A) and high-energy vibratory mill (B), with posterior analyze by SEM and particle size distribution. The powders showed different average and distribution of grain size. Finally, the cement obtained by the process (B) showed values of axial tensile strength significantly greater than that obtained by the process (A). The milling process (B) is much more efficient than the process (A). (author)

Morphology and magnetic properties of CeCo5 submicron flakes prepared by surfactant-assisted high-energy ball milling

International Nuclear Information System (INIS)

Zhang, J.J.; Gao, H.M.; Yan, Y.; Bai, X.; Su, F.; Wang, W.Q.; Du, X.B.

2012-01-01

CeCo 5 permanent magnetic alloy has been processed by surfactant assisted high energy ball milling. Heptane and oleic acid were used as the solvent and surfactant, respectively. The amount of surfactant used was 50% by weight of the starting powder. The produced particles were deposited on a piece of copper (4 mm in length and width) under a magnetic field of 27 kOe applied along the copper surface and immobilized by ethyl α-cyanoacrylate. Scanning electron microscope pictures show that the particles are flakes, several μm in length and width and tens of nm in thickness. X-ray diffraction patterns and magnetic measurements prove that the flakes are crystalline with c-axes magnetic anisotropy. The easy magnetization axis is oriented perpendicular to the surface of the flake. A maximum coercivity of 3.3 kOe was obtained for the sample milled for 40 min. - Highlights: ► CeCo 5 permanent magnetic alloy has been processed by surfactant assisted high energy ball milling (HEBM). ► The particles show a flake-like morphology with several μm in length and width and tens nm in thickness. ► The flakes are crystallographic and magnetic anisotropic and the c-axes, also the easy magnetization directions are oriented perpendicular to the surface of the flake. ► Maximum coercivity of 3.3 kOe has been obtained for the sample milled for 40 min.

Characterization of Tool Wear in High-Speed Milling of Hardened Powder Metallurgical Steels

Directory of Open Access Journals (Sweden)

Fritz Klocke

2011-01-01

Full Text Available In this experimental study, the cutting performance of ball-end mills in high-speed dry-hard milling of powder metallurgical steels was investigated. The cutting performance of the milling tools was mainly evaluated in terms of cutting length, tool wear, and cutting forces. Two different types of hardened steels were machined, the cold working steel HS 4-2-4 PM (K490 Microclean/66 HRC and the high speed steel HS 6-5-3 PM (S790 Microclean/64 HRC. The milling tests were performed at effective cutting speeds of 225, 300, and 400 m/min with a four fluted solid carbide ball-end mill (0 = 6, TiAlN coating. It was observed that by means of analytically optimised chipping parameters and increased cutting speed, the tool life can be drastically enhanced. Further, in machining the harder material HS 4-2-4 PM, the tool life is up to three times in regard to the less harder material HS 6-5-3 PM. Thus, it can be assumed that not only the hardness of the material to be machined plays a vital role for the high-speed dry-hard cutting performance, but also the microstructure and thermal characteristics of the investigated powder metallurgical steels in their hardened state.

Morphology and magnetic properties of CeCo5 submicron flakes prepared by surfactant-assisted high-energy ball milling

Science.gov (United States)

Zhang, J. J.; Gao, H. M.; Yan, Y.; Bai, X.; Su, F.; Wang, W. Q.; Du, X. B.

2012-10-01

CeCo5 permanent magnetic alloy has been processed by surfactant assisted high energy ball milling. Heptane and oleic acid were used as the solvent and surfactant, respectively. The amount of surfactant used was 50% by weight of the starting powder. The produced particles were deposited on a piece of copper (4 mm in length and width) under a magnetic field of 27 kOe applied along the copper surface and immobilized by ethyl α-cyanoacrylate. Scanning electron microscope pictures show that the particles are flakes, several μm in length and width and tens of nm in thickness. X-ray diffraction patterns and magnetic measurements prove that the flakes are crystalline with c-axes magnetic anisotropy. The easy magnetization axis is oriented perpendicular to the surface of the flake. A maximum coercivity of 3.3 kOe was obtained for the sample milled for 40 min.

Microstructural analysis of sinterized aluminum powder obtained by the high energy milling of beverage cans

International Nuclear Information System (INIS)

Souza, Jose Raelson Pereira de; Peres, Mauricio Mhirdaui

2016-01-01

The objective is the study of the effect of high energy milling on the sintering of aluminum from beverage cans. The selected aluminum cans were cut and subjected to high energy milling under a common atmosphere (in the air). In milling, three grams of aluminum was used to maintain the ratio of 10/1 between the mass of the beads and the material. The milling time was varied in 1h, 1.5h and 2h, keeping the other variables constant. The particle size distribution was measured by laser granulometry, for further compaction and sintering at a temperature of 600 ° C for 2 h. The samples were characterized by scanning electron microscopy (SEM). The granulometric analysis of the powders found that higher milling times produced finer particles. Powders with granulometry of less than 45 μm were obtained at 1 h, 1.5 h and 2 h times. The times of 1.5h and 2h promoted finer particles with better distribution of size. The SEM analyzes showed little variation in the shape of the particles as a function of the variation of the grinding times, presenting irregularities in the platelet geometry. The sintering time and temperature were effective in the densification of the powder particles, which were influenced by the average particle size

Improved critical current densities in bulk FeSe superconductor using ball milled powders and high temperature sintering

Energy Technology Data Exchange (ETDEWEB)

Muralidhar, M.; Furutani, K.; Murakami, M. [Graduate School of Science and Engineering, Superconducting Materials Laboratory, Shibaura Institute of Technology, Tokyo (Japan); Kumar, Dinesh; Rao, M.S. Ramachandra [Department of Physics, Nano Functional Materials Technology Centre and Materials Science Research Centre, Indian Institute of Technology Madras, Chennai (India); Koblischka, M.R. [Institute of Experimental Physics, Saarland University, Saarbruecken (Germany)

2016-12-15

The present study is investigating the effect of high temperature sintering combined with ball milled powders for the preparation of FeSe material via solid state sintering technique. The commercial powders of Fe (99.9% purity) and Se (99.9% purity) were mixed in a nominal ratio Fe:Se = 1:1 and thoroughly ground and ball-milled in a glove box during 6 h. Then, the powder mixture was pressed into pellets of 5 mm in diameter and 2 mm thickness using an uniaxial pressure of 100 MPa. The samples were sealed in quartz tubes and sintered at 600 C for 24 h. Then, the pellets were again thoroughly ground and ball-milled in the glove box and pressed into pellets, and the final sintering was performed at two different temperatures, namely at 900 C for 24 h and at 950 C for 24 h. X-ray diffraction results confirmed that both samples showed mainly of the β-FeSe with tetragonal structure. The temperature dependence of magnetization (M-T) curves revealed a sharp superconducting transition T{sub c,} {sub onset} = 8.16 K for the sample sintered at 900 C. Further, scanning electron microscopy observations proved that samples sintered at 900 C show a platelike grain structure with high density. As a result, improved irreversibility fields around 5 T and the critical current density (J{sub c}) values of 6252 A cm{sup -2} at 5 K and self-field are obtained. Furthermore, the normalized volume pinning force versus the reduced field plots indicated a peak position at 0.4 for the sample sintered at 900 C. Improved flux pinning and the high J{sub c} values are attributed to the textured microstructure of the material, produced by a combination of high temperature sintering and ball milling. (copyright 2016 The Authors. Phys. Status Solidi A published by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Positron annihilation lifetime spectroscopy of mechanically milled protein fibre powders and their free volume aspects

International Nuclear Information System (INIS)

Patil, K; Rajkhowa, R; Tsuzuki, T; Lin, T; Wang, X; Sellaiyan, S; Smith, S V; Uedono, A

2013-01-01

The present study reports the fabrication of ultra-fine powders from animal protein fibres such as cashmere guard hair, merino wool and eri silk along with their free volume aspects. The respectively mechanically cleaned, scoured and degummed cashmere guard hair, wool and silk fibres were converted into dry powders by a process sequence: Chopping, Attritor Milling, and Spray Drying. The fabricated protein fibre powders were characterised by scanning electron microscope, particle size distribution and positron annihilation lifetime spectroscopy (PALS). The PALS results indicated that the average free volume size in protein fibres increased on their wet mechanical milling with a decrease in the corresponding intensities leading to a resultant decrease in their fractional free volumes.

Dopants incorporation in ZnO mechanical milled powders sensed by positrons

International Nuclear Information System (INIS)

Damonte, L. C.; Donderis, V.; Hernandez Fenollosa, M. A.

2007-01-01

M-doped ZnO (M: Cd, Mg) powders obtained by mechanical milling were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and positron lifetime annihilation spectroscopy (PALS). The mixing of the oxides is followed by means of XRD and SEM. As milling proceeds, a clear reduction of grain size and homogenization are observed. The evolution of annihilation parameters with milling time and cation content were analyzed and related with the kind of mechanical induced defect involved. Ternary oxides Zn 1-x M x O were efficiency obtained for certain compositions. The results showed that positrons constitute a well suited probe to characterize the cation substitution in the ZnO oxide lattice.

Dopants incorporation in ZnO mechanical milled powders sensed by positrons

Energy Technology Data Exchange (ETDEWEB)

Damonte, L. C., E-mail: damonte@fisica.unlp.edu.ar; Donderis, V.; Hernandez Fenollosa, M. A. [Universidad Politecnica de Valencia, Departamento de Fisica Aplicada (Spain)

2007-09-15

M-doped ZnO (M: Cd, Mg) powders obtained by mechanical milling were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and positron lifetime annihilation spectroscopy (PALS). The mixing of the oxides is followed by means of XRD and SEM. As milling proceeds, a clear reduction of grain size and homogenization are observed. The evolution of annihilation parameters with milling time and cation content were analyzed and related with the kind of mechanical induced defect involved. Ternary oxides Zn{sub 1-x}M{sub x}O were efficiency obtained for certain compositions. The results showed that positrons constitute a well suited probe to characterize the cation substitution in the ZnO oxide lattice.

Modeling of magnetic particle orientation in magnetic powder injection molding

Science.gov (United States)

Doo Jung, Im; Kang, Tae Gon; Seul Shin, Da; Park, Seong Jin

2018-03-01

The magnetic micro powder orientation under viscous shear flow has been analytically understood and characterized into a new analytical orientation model for a powder injection molding process. The effects of hydrodynamic force from the viscous flow, external magnetic force and internal dipole-dipole interaction were considered to predict the orientation under given process conditions. Comparative studies with a finite element method proved the calculation validity with a partial differential form of the model. The angular motion, agglomeration and magnetic chain formation have been simulated, which shows that the effect of dipole-dipole interaction among powders on the orientation state becomes negligible at a high Mason number condition and at a low λ condition (the ratio of external magnetic field strength and internal magnetic moment of powder). Our developed model can be very usefully employed in the process analysis and design of magnetic powder injection molding.

Structural and magnetic properties of ball milled copper ferrite

DEFF Research Database (Denmark)

Goya, G.F.; Rechenberg, H.R.; Jiang, Jianzhong

1998-01-01

The structural and magnetic evolution in copper ferrite (CuFe2O4) caused by high-energy ball milling are investigated by x-ray diffraction, Mössbauer spectroscopy, and magnetization measurements. Initially, the milling process reduces the average grain size of CuFe2O4 to about 6 nm and induces....... The canted spin configuration is also suggested by the observed reduction in magnetization of particles in the blocked state. Upon increasing the milling time, nanometer-sized CuFe2O4 particles decompose, forming alpha-Fe2O3 and other phases, causing a further decrease of magnetization. After a milling time...... of 98 h, alpha-Fe2O3 is reduced to Fe3O4, and magnetization increases accordingly to the higher saturation magnetization value of magnetite. Three sequential processes during high-energy ball milling are established: (a) the synthesis of partially inverted CuFe2O4 particles with a noncollinear spin...

Preparation of zinc ferrite nano powders by high energy wet-milling method and investigation of Crystallites size variation during this process

International Nuclear Information System (INIS)

Masoudi, H.; Aftabi, A.; Mozafari, M.; Amighian, J.

2007-01-01

In this research work ZnFe 2 O 4 nano powders were prepared by high-energy wet-milling process, using metallic Fe and Zn powders. The process was investigated by XRD technique. 10% of the zinc ferrite was formed after 10 h milling. The as-milled sample was annealed at 500, 550 and 600 d egree C . Ultimately a single sample was obtained at 600 d egree C . Using sherrer's formula, the mean crystallite size of the as-milled and annealed powders were calculated. These were in the range of 17.9 to 20.4 nm.

Nano-composite powders Ag-SnO2 prepared by reactive milling sintering and microstructural evolution

International Nuclear Information System (INIS)

Lorrain, Nathalie

2000-01-01

This work aims at controlling the synthesis and the sintering of nano-composite powders Ag-SnO 2 in order to obtain a dense and nano-structured material for electrical contact as a substitute of the toxic compound Ag - CdO. The powder is prepared by reactive milling from silver oxide (Ag 2 O) and silver bronze (Ag 3 Sn) powders. This process leads to a fine dispersion of silver and tin oxide nanometer sized particles. We first studied the mechanisms of reaction promoted by milling in vacuum and in air. A two-stage oxidation of tin in Ag 3 Sn occurs: during forced contact with Ag 2 O, tin oxidises in SnO, then in SnO 2 . In air, gaseous oxygen also participates to the oxidation of tin in SnO 2 but the reaction is slower because of the formation of silver carbonates from a reaction of Ag 2 O with CO 2 .Then the sintering behaviour of the nano-composite powder as a function of the compacting pressure and of the heating rate has been studied. We show: (i) a diffusion of pure silver towards porosity and free surfaces (exo-diffusion) which destroys the nano-structure and (ii) a severe de-densification. We show that the origin of these phenomena is due to carbonates on to the Ag 2 O starting powder, which are incorporated, in the milled Ag-SnO 2 powder in course of milling; during sintering, decomposition gases generate internal stresses. Low stresses lead to a diffusional creep with exo-diffusion whereas high stresses induce an intensive de-densification by local plastic deformation but no exo-diffusion. A modelling shows that exo-diffusion is limited by heating very quickly a strongly compacted powder that contains a high quantity of carbonates. The experimental results confirm the predictions of the model. Finally, we propose solutions allowing a full densification and a process for decreasing the tin oxide concentration. (author) [fr

Al-doped ZnO mechanical milled powders for dye sensitized cells

International Nuclear Information System (INIS)

Damonte, L.C.; Donderis, V.; Ferrari, S.; Orozco, J.; Hernandez-Fenollosa, M.A.

2010-01-01

Mixtures of Al 2 O 3 and ZnO powders were prepared by mechanical milling. The resulting samples were analyzed and characterized by X-ray diffraction (XRD), positron annihilation lifetime spectroscopy (PALS), scanning electron microscopy (SEM) and optical reflection spectroscopy (OPS). XRD and PALS measurements confirm Al incorporation into ZnO wurtzite structure. Powders obtained from Al 2 O 3 precursors display better reflectivity than those prepared from Al metal so they might be better materials for implementation in photovoltaic solar devices.

Structure and magnetism of SmCo5 nanoflakes prepared by surfactant-assisted ball milling with different ball sizes

International Nuclear Information System (INIS)

Nie, Junwu; Han, Xianghua; Du, Juan; Xia, Weixing; Zhang, Jian; Guo, Zhaohui; Yan, Aru; Li, Wei; Ping Liu, J.

2013-01-01

Anisotropic magnetic SmCo 5 nanoflakes have been fabricated by surfactant-assisted ball milling (SABM) using hardened steel balls of one of the following sizes: 4, 6.5, 9.5 and 12.7 mm in diameters. The magnetic properties of SmCo 5 particles prepared by SABM with different milling ball sizes in diameters were investigated systematically. It was showed that the nanoflakes milled by amount of small size balls had a higher coercivity and lower anisotropy, i.e., worse grain orientation although in a short milling time while the nanoflakes prepared with same weight of big balls tend to have a lower coercivity, better grain orientation. The coercivity mechanism of the nanoflake was studied and it was mainly dominated with the domain-wall pinning. The SEM analysis shows that the morphology of nanoflakes prepared with different ball sizes are almost the same when the balls to powder weight ratio is fixed. The different magnetic properties caused by different ball sizes are mainly due to the different microstructure changes, i.e, grain refinement and c-axis orientation, which are demonstrated by X-ray diffraction (XRD) analysis and transmission electron microscope (TEM). Based on the experiments above, a combined milling process was suggested and done to improve magnetic properties as your need. - Highlights: • We fabricated anisotropic magnetic SmCo 5 nanoflakes by surfactant-assisted ball milling (SABM). • We investigated the magnetic properties of SmCo 5 particles systematically. It was showed that the coercivity, high or low, and grain orientation, good or bad, were influenced strongly by balls size. The different magnetisms caused by different ball sizes is mainly due to the different microstructure changes. • The coercivity mechanism of the nanoflake was studied and it was mainly dominated with the domain-wall pinning

Effect of milling duration on the evolution of shape memory properties in a powder processed Cu-Al-Ni-Ti alloy

Energy Technology Data Exchange (ETDEWEB)

Sharma, Mohit; Gupta, Gaurav K.; Shafeeq, Muhamed M.; Modi, Om P.; Prasad, Braj K. [CSIR - Advanced Materials and Processes Research Institute, Bhopal (India)

2013-09-15

The present work describes the effect of milling duration on the properties of a powder metallurgy processed Cu-Al-Ni-Ti shape memory alloy employing mechanical alloying. Powder mixtures milled for different durations were sintered in order to investigate the formation of solid solution and evolution of martensitic structure. The idea was to optimize the duration of milling (mechanical alloying) to obtain chemical homogeneity as well as shape memory properties in the processed material without undergoing extensive post homogenization treatment. The martensitic structure was noted to evolve in the powder mix milled for at least 16 hrs, whereas complete transformation to martensite occurred after milling for 40 hrs. Interestingly, the dissolution of alloying elements (to form the {beta} phase prior to the formation of martensite) was noted to complete partially only during mechanical alloying for 40 hrs and remaining during subsequent sintering for 1 hr. The hot pressed compacts of the powders milled for 40 hrs were chemically homogeneous and consisted of fully martensite phase, which is essential for the realization of shape memory properties. They also revealed almost 100% shape recovery at the applied pre-strain levels of 1 and 2%. (orig.)

Fabrication of Al2O3–20 vol.% Al nanocomposite powders using high energy milling and their sinterability

International Nuclear Information System (INIS)

Zawrah, M.F.; Abdel-kader, H.; Elbaly, N.E.

2012-01-01

Highlights: ► Al 2 O 3 /Al nanocomposite powders were prepared via high energy ball milling. After 20 h milling, the size of Al 2 O 3 –20 vol.% Al nanocomposite particles was in the range of 23–29 nm. A uniform distribution of nanosized Al reinforcement throughout the Al 2 O 3 matrix, coating the particles was successfully obtained. ► There was no any sign of phase changes during the milling. A competition between the cold welding mechanism and the fracturing mechanism were found during milling and finally the above two mechanisms reached an equilibrium. ► The highest value of relative density was obtained for the sintered bodies at 1500 °C. ► The harness of the sintered composite was decreased while the fracture toughness was improved after addition Al into alumina. -- Abstract: In this study, alumina-based matrix nanocomposite powders reinforced with Al particles were fabricated and investigated. The sinterability of the prepared nanocomposite powder at different firing temperature was also conducted. Their mechanical properties in terms of hardness and toughness were tested. Alumina and aluminum powder mixtures were milled in a planetary ball mill for various times up to 30 h in order to produce Al 2 O 3 –20% Al nanocomposite. The phase composition, morphological and microstructural changes during mechanical milling of the nanocomposite particles were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM) techniques, respectively. The crystallite size and internal strain were evaluated by XRD patterns using Scherrer methods. A uniform distribution of the Al reinforcement in the Al 2 O 3 matrix was successfully obtained after milling the powders. The results revealed that there was no any sign of phase changes during the milling. The crystal size decreased with the prolongation of milling times, while the internal strain increased. A simple model is presented to illustrate the mechanical

Morphology and magnetic properties of CeCo{sub 5} submicron flakes prepared by surfactant-assisted high-energy ball milling

Energy Technology Data Exchange (ETDEWEB)

Zhang, J.J.; Gao, H.M.; Yan, Y.; Bai, X.; Su, F.; Wang, W.Q. [State key Laboratory for Superhard Materials and Department of Physics, Jilin University, Changchun 130012 (China); Du, X.B., E-mail: duxb@jlu.edu.cn [State key Laboratory for Superhard Materials and Department of Physics, Jilin University, Changchun 130012 (China)

2012-10-15

CeCo{sub 5} permanent magnetic alloy has been processed by surfactant assisted high energy ball milling. Heptane and oleic acid were used as the solvent and surfactant, respectively. The amount of surfactant used was 50% by weight of the starting powder. The produced particles were deposited on a piece of copper (4 mm in length and width) under a magnetic field of 27 kOe applied along the copper surface and immobilized by ethyl {alpha}-cyanoacrylate. Scanning electron microscope pictures show that the particles are flakes, several {mu}m in length and width and tens of nm in thickness. X-ray diffraction patterns and magnetic measurements prove that the flakes are crystalline with c-axes magnetic anisotropy. The easy magnetization axis is oriented perpendicular to the surface of the flake. A maximum coercivity of 3.3 kOe was obtained for the sample milled for 40 min. - Highlights: Black-Right-Pointing-Pointer CeCo{sub 5} permanent magnetic alloy has been processed by surfactant assisted high energy ball milling (HEBM). Black-Right-Pointing-Pointer The particles show a flake-like morphology with several {mu}m in length and width and tens nm in thickness. Black-Right-Pointing-Pointer The flakes are crystallographic and magnetic anisotropic and the c-axes, also the easy magnetization directions are oriented perpendicular to the surface of the flake. Black-Right-Pointing-Pointer Maximum coercivity of 3.3 kOe has been obtained for the sample milled for 40 min.

Effects of milling method and calcination condition on phase and morphology characteristics of Mg4Nb2O9 powders

International Nuclear Information System (INIS)

Wongmaneerung, R.; Sarakonsri, T.; Yimnirun, R.; Ananta, S.

2006-01-01

Magnesium niobate, Mg 4 Nb 2 O 9 , powders has been synthesized by a solid-state reaction. Both conventional ball- and rapid vibro-milling have been investigated as milling methods, with the formation of the Mg 4 Nb 2 O 9 phase investigated as a function of calcination conditions by DTA and XRD. The particle size distribution of the calcined powders was determined by laser diffraction technique, while morphology, crystal structure and phase composition were determined via a combination of SEM, TEM and EDX techniques. The type of milling method together with the designed calcination condition was found to show a considerable effect on the phase and morphology evolution of the calcined Mg 4 Nb 2 O 9 powders. It is seen that optimization of calcination conditions can lead to a single-phase Mg 4 Nb 2 O 9 in both milling methods. However, the formation temperature and dwell time for single-phase Mg 4 Nb 2 O 9 powders were lower with the rapid vibro-milling technique

Al-doped ZnO mechanical milled powders for dye sensitized cells

Energy Technology Data Exchange (ETDEWEB)

Damonte, L.C., E-mail: damonte@fisica.unlp.edu.a [Departamento de Fisica, UNLP, IFLP-CCT-CONICET, C.C.67(1900), La Plata (Argentina); Dto. de Fisica Aplicada, Universidad Politecnica de Valencia, Cami de Vera s/n, 46022 Valencia (Spain); Donderis, V. [Dto. de Ingenieria Electrica, Universidad Politecnica de Valencia, Cami de Vera s/n, 46022 Valencia (Spain); Ferrari, S. [Departamento de Fisica, UNLP, IFLP-CCT-CONICET, C.C.67(1900), La Plata (Argentina); Orozco, J. [ITM, Universidad Politecnica de Valencia, Cami de Vera s/n, 46022 Valencia (Spain); Hernandez-Fenollosa, M.A. [Dto. de Fisica Aplicada, Universidad Politecnica de Valencia, Cami de Vera s/n, 46022 Valencia (Spain)

2010-04-16

Mixtures of Al{sub 2}O{sub 3} and ZnO powders were prepared by mechanical milling. The resulting samples were analyzed and characterized by X-ray diffraction (XRD), positron annihilation lifetime spectroscopy (PALS), scanning electron microscopy (SEM) and optical reflection spectroscopy (OPS). XRD and PALS measurements confirm Al incorporation into ZnO wurtzite structure. Powders obtained from Al{sub 2}O{sub 3} precursors display better reflectivity than those prepared from Al metal so they might be better materials for implementation in photovoltaic solar devices.

Complex permeability and core loss of soft magnetic Fe-based nanocrystalline powder cores

Energy Technology Data Exchange (ETDEWEB)

Füzerová, Jana, E-mail: jana.fuzerova@tuke.sk [Faculty of Mechanical Engineering, Technical University, Letná 1, 042 00 Košice (Slovakia); Füzer, Ján; Kollár, Peter [Institute of Physics, P.J. Šafárik University, Park Angelinum 9, 040 23 Košice (Slovakia); Bureš, Radovan; Fáberová, Mária [Institute of Materials Research, Slovak Academy of Sciences, Watsonova 47, 043 53 Košice (Slovakia)

2013-11-15

Rapidly quenched ribbons of Fe{sub 73}Cu{sub 1}Nb{sub 3}Si{sub 16}B{sub 7} were ball milled and cryomilled to get powder and warm consolidated to get bulk compacts. The data presented here are relative to different experimental procedures, one corresponding to milling at room temperature (sample R1) and the other corresponding to cryomilling at temperature of liquid nitrogen (sample L1). It was found that the properties of the initial powder influenced the density, the electrical resistivity and electromagnetic properties of the resulting bulk alloys. Permeability and core loss are structure sensitive and depend on factors such as powder size and shape, porosity, purity, and internal stress. Permeability spectra of sample R1 decreases with increasing the frequency and its values are larger than that for sample L1 at low frequencies. On the other hand the permeability of sample L1 remains steady up to 1 kHz and at certain frequency is larger than that for sample R1. Also there are different frequency dependences of the imaginary parts of permeability and loss factor, respectively. The cryomilling of the amorphous ribbon positively influences on the AC magnetic properties at higher frequencies (above 100 Hz) of resulting bulk sample. - Highlights: • We prepared two different amorphous powder vitroperm samples. • We have examined changes in the properties of the bulk samples prepared by compaction. • It was found that properties of the initial powder influence the density, the electrical resistivity and electromagnetic properties of the resulting bulk alloys.

Defect induced electronic states and magnetism in ball-milled graphite.

Science.gov (United States)

Milev, Adriyan; Dissanayake, D M A S; Kannangara, G S K; Kumarasinghe, A R

2013-10-14

The electronic structure and magnetism of nanocrystalline graphite prepared by ball milling of graphite in an inert atmosphere have been investigated using valence band spectroscopy (VB), core level near-edge X-ray absorption fine structure (NEXAFS) spectroscopy and magnetic measurements as a function of the milling time. The NEXAFS spectroscopy of graphite milled for 30 hours shows simultaneous evolution of new states at ~284.0 eV and at ~290.5 eV superimposed upon the characteristic transitions at 285.4 eV and 291.6 eV, respectively. The modulation of the density of states is explained by evolution of discontinuities within the sheets and along the fracture lines in the milled graphite. The magnetic measurements in the temperature interval 2-300-2 K at constant magnetic field strength show a correlation between magnetic properties and evolution of the new electronic states. With the reduction of the crystallite sizes of the graphite fragments, the milled material progressively changes its magnetic properties from diamagnetic to paramagnetic with contributions from both Pauli and Curie paramagnetism due to the evolution of new states at ~284 and ~290.5 eV, respectively. These results indicate that the magnetic behaviour of ball-milled graphite can be manipulated by changing the milling conditions.

High anisotropic NdFeB submicro/nanoflakes prepared by surfactant-assisted ball milling at low temperature

Science.gov (United States)

An, Xiaoxin; Jin, Kunpeng; Abbas, Nadeem; Fang, Qiuli; Wang, Fang; Du, Juan; Xia, Weixing; Yan, Aru; Liu, J. Ping; Zhang, Jian

2017-11-01

Hard magnetic NdFeB submicro/nanoflakes were successfully prepared by surfactant-assisted ball milling at low temperature (SABMLT) by specially using 2-methyl pentane and trioctylamine (TOA) as solvent and surfactant, respectively. Influences of the amount of TOA and milling temperature on the crystal structure, morphology and magnetic performances of the as-prepared NdFeB powders were investigated systematically. There is significant difference on morphology between the NdFeB powders milled at room and low temperature. The NdFeB powders with flaky morphology could be obtained even with a small amount of TOA by SABMLT, which could not be achieved by surfactant-assisted ball milling at room temperature (SABMRT). The better crystallinity, better grain alignment, higher coercivity, larger saturation magnetization and remanence ratio were achieved in the samples prepared by SABMLT. Furthermore, the final NdFeB powders prepared by SABMLT possessed a lower amount of residual TOA than those prepared by SABMRT. It was demonstrated that SABMLT is a promising way to fabricate rare-earth-transition metal nanoflakes with high anisotropy for permanent magnetic materials. The effective method of preparing NdFeB flakes by lowering temperature will be also useful to fabricate flakes of other functional materials.

Magnetic characterization of nanocrystalline Fe{sub 80−x}Cr{sub x}Co{sub 20} (15≤x≤35) alloys during milling and subsequent annealing

Energy Technology Data Exchange (ETDEWEB)

Rastabi, Reza Amini; Ghasemi, Ali, E-mail: ali13912001@yahoo.com; Tavoosi, Majid; Sodaee, Tahmineh

2016-10-15

Magnetic characterization of nanocrystalline Fe–Cr–Co alloys during milling and annealing process was the goal of this study. To formation of Fe{sub 80−x}Cr{sub x}Co{sub 20} (15≤x≤35) solid solution, different powder mixtures of Fe, Cr and Co elements were mechanically milled in a planetary ball mill. The annealing process was done in as-milled samples at different temperature in the range of 500–640 °C for 2 h. The produced samples were characterized using X-ray diffraction, scanning electron microscopy, differential scanning calorimetry and vibrating sample magnetometer. Performed mechanical alloying in different powder mixtures lead to the formation of Fe–Cr–Co α-phase solid solution with average crystallite sizes of about 10 nm. The produced nanocrystalline alloys exhibit magnetic properties with the coercivity and saturation of magnetization in the range of 110–200 Oe and 150–220 emu/g, respectively. The coercivity of produced alloys after annealing process decreased and reached to about 40–150 Oe. The highest value of coercivity in as-milled and annealed samples was achieved in alloys with higher Cr contents. - Highlights: • Hc and Ms of produced alloys obtained in the range of 110–200 Oe and 150–220 emu/g. • The highest value of Hc in milled and annealed samples was achieved in Fe{sub 45}Cr{sub 35}Co{sub 20}. • Hc of produced alloys after spinodal decomposition decreased to about 40–150 Oe. • The effect of crystalline defects and residual strain on magnetic fields pinning in milled samples is higher than spinodal decomposition in annealed samples. • The highest value of Hc in as-milled and annealed samples was achieved in Fe{sub 45}Cr{sub 35}Co{sub 20}. The coercivity of produced alloys after annealing process decreased and reach to about 40–150 Oe. • The produced nanocrystalline alloys exhibit magnetic properties with the coercivity and saturation of magnetization in the range of 110–200 Oe and 150–220 emu

Processing of Polysulfone to Free Flowing Powder by Mechanical Milling and Spray Drying Techniques for Use in Selective Laser Sintering

Directory of Open Access Journals (Sweden)

Nicolas Mys

2016-04-01

Full Text Available Polysulfone (PSU has been processed into powder form by ball milling, rotor milling, and spray drying technique in an attempt to produce new materials for Selective Laser Sintering purposes. Both rotor milling and spray drying were adept to make spherical particles that can be used for this aim. Processing PSU pellets by rotor milling in a three-step process resulted in particles of 51.8 μm mean diameter, whereas spray drying could only manage a mean diameter of 26.1 μm. The resulting powders were characterized using Differential Scanning Calorimetry (DSC, Gel Permeation Chromatography (GPC and X-ray Diffraction measurements (XRD. DSC measurements revealed an influence of all processing techniques on the thermal behavior of the material. Glass transitions remained unaffected by spray drying and rotor milling, yet a clear shift was observed for ball milling, along with a large endothermic peak in the high temperature region. This was ascribed to the imparting of an orientation into the polymer chains due to the processing method and was confirmed by XRD measurements. Of all processed powder samples, the ball milled sample was unable to dissolve for GPC measurements, suggesting degradation by chain scission and subsequent crosslinking. Spray drying and rotor milling did not cause significant degradation.

Magneto-structural transformations in Ni{sub 50}Mn{sub 37.5}Sn{sub 12.5−x}In{sub x} Heusler powders

Energy Technology Data Exchange (ETDEWEB)

Maziarz, Wojciech; Wójcik, Anna; Czaja, Paweł [Instituite of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta Str, 30-059 Kraków (Poland); Żywczak, Antoni [AGH University of Science and Technology, Academic Centre for Materials and Nanotechnology, Mickiewicza 30, 30-059 Kraków (Poland); Jan Dutkiewicz [Instituite of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta Str, 30-059 Kraków (Poland); Hawełek, Łukasz [Institute of Non-Ferrous Metals, ul. Sowinskiego 5, 44-100 Gliwice (Poland); Cesari, Eduard [Department de Física, Universitat de les Illes Balears, Ctra. de Valldemossa, km 7.5, Palma de Mallorca E-07122 (Spain)

2016-08-15

The effect of ball milling and subsequently annealing of melt spun ribbons on magneto-structural transformations in Ni{sub 50}Mn{sub 37.5}Sn{sub 12.5−x}In{sub x} (x=0, 2, 4, 6) ribbons is presented. Short time vibration milling allows to obtain chemically homogenous powders of angular particle shapes and size within 10–50 μm. Milling does not change the characteristic temperatures of martensitic transformation in comparison to the melt spun ribbons. The effect of In substitution for Sn on martensitic transformation has a complex mechanism, associated with electron density change. Substitution of Sn by In in both milled and annealed powders leads to decrease of Curie temperature of austenite and increase of martensitic transformation temperature, stabilizing martensitic phase. The coexistence of magnetic transformation of austenite and martensitic transformation at low magnetic field was observed. The intermartensitic transformation of 4O martensite to L1{sub 0} martensite was observed during cooling at low magnetic field and this was confirmed by TEM microstructure observations. The annealing process of as-milled powders leads to the change of their martensitic structure due to relaxation of internal stresses associated with anisotropic columnar grain microstructure formed during melt spinning process. The level of stresses introduced during milling of ribbons has no significant influence on martensitic transformation. The annealing process of as milled powders leads to enhancement of their magnetic properties, decrease of Curie temperature of austenite, and marginal change of temperature of martenisitic transformation. - Highlights: • Vibration milling of ribbons allows to obtain angular powders of size 10–50 μm. • Vibration milling improves chemical homogeneity of alloys. • Indium addition changes the magneto-structural transformations in Ni–Mn–Sn–In alloys. • Complex character of magneto-structural transformations is visible. • Multistep

Phase evolution during early stages of mechanical alloying of Cu–13 wt.% Al powder mixtures in a high-energy ball mill

International Nuclear Information System (INIS)

Dudina, Dina V.; Lomovsky, Oleg I.; Valeev, Konstantin R.; Tikhov, Serguey F.; Boldyreva, Natalya N.; Salanov, Aleksey N.; Cherepanova, Svetlana V.; Zaikovskii, Vladimir I.; Andreev, Andrey S.; Lapina, Olga B.; Sadykov, Vladislav A.

2015-01-01

Highlights: • Phase formation during early stages of Cu–Al mechanical alloying was studied. • The products of mechanical alloying are of highly non-equilibrium character. • X-ray amorphous phases are present in the products of mechanical alloying. • An Al-rich X-ray amorphous phase is distributed between the crystallites. - Abstract: We report the phase and microstructure evolution of the Cu–13 wt.% Al mixture during treatment in a high-energy planetary ball mill with a particular focus on the early stages of mechanical alloying. Several characterization techniques, including X-ray diffraction phase analysis, nuclear magnetic resonance spectroscopy, differential dissolution, thermal analysis, and electron microscopy/elemental analysis, have been combined to study the evolution of the phase composition of the mechanically alloyed powders and describe the microstructure of the multi-phase products of mechanical alloying at different length scales. The following reaction sequence has been confirmed: Cu + Al → CuAl 2 (+Cu) → Cu 9 Al 4 + (Cu) → Cu(Al). The phase evolution was accompanied by the microstructure changes, the layered structure of the powder agglomerates disappearing with milling time. This scheme is further complicated by the processes of copper oxidation, reduction of copper oxides by metallic aluminum, and by variation of the stoichiometry of Cu(Al) solid solutions with milling time. Substantial amounts of X-ray amorphous phases were detected as well. Differential dissolution technique has revealed that a high content of aluminum in the Cu(Al) solid solution-based powders is due to the presence of Al-rich phases distributed between the Cu(Al) crystallites

Permanent magnets and its production by powder metallurgy

Directory of Open Access Journals (Sweden)

Enrique Herraiz Lalana

2018-06-01

Full Text Available In this work, the historical relationship between permanent magnets and powder metallurgy is reviewed. Powder metallurgy is a manufacturing technique based on the compaction of powders that are sintered to create a solid product. This technique was used in the production of permanent magnets for the first time in the 18th century and, nowadays, most permanent magnetic materials are manufacturing by this mean. Magnetic properties are highly dependent on the microstructure of the final product, the magnetic alignment of domains and presence of porosity, to mention a few, and powder metallurgy enables fine control of these factors.

Magnetically responsive enzyme powders

Czech Academy of Sciences Publication Activity Database

Pospišková, K.; Šafařík, Ivo

2015-01-01

Roč. 380, APR 2015 (2015), s. 197-200 ISSN 0304-8853 R&D Projects: GA MŠk(CZ) LD13021 Institutional support: RVO:67179843 Keywords : enzyme powders * cross-linking * magnetic modification * magnetic separation * magnetic iron oxides particles * microwave-assisted synthesis Subject RIV: CE - Biochemistry Impact factor: 2.357, year: 2015

Mechanical alloying and reactive milling in a high energy planetary mill

International Nuclear Information System (INIS)

Jiang Xianjin; Trunov, Mikhaylo A.; Schoenitz, Mirko; Dave, Rajesh N.; Dreizin, Edward L.

2009-01-01

Powder refinement in a planetary mill (Retsch PM 400-MA) is investigated experimentally and analyzed using discrete element modeling (DEM). Refinement is defined as the average size of the individual components in a composite powder. The specific milling dose, defined as the product of charge ratio and milling time, is used as an experimental parameter tracking the progress of the material refinement. This parameter is determined experimentally for milling of boron and titanium powders, for which the time of initiation of a self-sustained reaction is measured under different milling conditions. It is assumed that the reaction becomes self-sustaining when the same powder refinement is achieved. The DEM calculations established that the milling balls primarily roll along the milling container's perimeter. The inverse of the rate of energy dissipation resulting from this rolling motion is used as the DEM analog of the specific milling dose. The results correlate well with experimental observations.

Barium Ferrite Ball Milled in Vacuum

International Nuclear Information System (INIS)

Campbell, S.J.; Wu, E.; Kaczmarek, W.A.; Wang, G.

1998-01-01

The structural and magnetic behaviour of BaFe 12 O 19 subjected to milling in vacuum for 1000 h has been investigated by x-ray powder diffraction and Moessbauer effect spectroscopy techniques. Pronounced structural disorder is obtained along with partial decomposition of BaFe 12 O 19 to α-Fe 2 O 3 and evidence for superparamagnetic relaxation effects due to the fine particles produced on milling. Restoration of the fully crystallised BaFe 12 O 19 structure on annealing at 1000 deg. C is accompanied by a six fold enhancement in the magnetic coercivity. This behaviour is linked with the fine crystallites

The magnetic properties of mill scale-derived permanent magnet

International Nuclear Information System (INIS)

Woon, H.S.; Hashim, M.M.; Yahya, N.; Zakaria, A.; Lim, K.P.

2005-01-01

In the permanent magnet SrO-FeO-Fe 2 O 3 system, there exist several magnetically ordered compounds with a stable phase at room temperature. The most important are the M(SrFe 12 O 19 ), X(SrFe 15 O 23 ) and W(SrFe 18 O 27 ) phases with hexagonal close packed structure. In this project, M(SrFe 12 O 19 ) was prepared using mill scale, a steel-maker byproduct, as raw material. The Malaysia steel industry generates approximately 30,000 metric tons of waste products such as mill scale every year. Transportation and disposal of the byproducts are costly and the environmental regulations are becoming stricter. Hence, local steel mills are to find new ways to recycle the waste as a feedstock for the steel-making process or as a saleable product. The M(SrFe 12 O 19 ) was synthesized using the conventional ceramic process. The formation of the SrFe 12 O 19 was confirmed by X-ray diffraction. The magnetic properties such as the energy product (BH)max, coercive force (iHc) and remanence (Br) were also reported in this paper. (Author)

Performance enhancement of NdFeB nanoflakes prepared by surfactant-assisted ball milling at low temperature by using different surfactants

Science.gov (United States)

An, Xiaoxin; Jin, Kunpeng; Wang, Fang; Fang, Qiuli; Du, Juan; Xia, Weixing; Yan, Aru; Liu, J. Ping; Zhang, Jian

2017-02-01

Hard magnetic NdFeB submicron and nanoflakes were successfully prepared by surfactant-assisted ball milling at room temperature (SABMRT) and low temperature (SABMLT) by using oleic acid (OA), oleylamine (OLA) and trioctylamine (TOA) as surfactant, respectively. Among the surfactants used, OA and OLA have similar effects on the morphology of the NdFeB nanoflakes milled at both room and low temperature. In the case of TOA, irregular micron-sized particles and submirco/nanoflakes were obtained for the NdFeB powders prepared by SABMRT and SABMLT, respectively. Samples prepared by SABMLT show better crystallinity and better degree of grain alignment than that prepared by SABMRT with the same surfactant. Comparing with the samples milled at RT, higher coercivity and larger remanence ratio were achieved in the NdFeB samples prepared at LT. The amounts of residual surfactants in final NdFeB powders were also calculated, which reveals that the final NdFeB powders milled at LT possess lower amount of residual surfactants than those milled at RT. It was found that lowering milling temperature of SABM would be a promising way for fabricating permanent magnetic materials with better hard magnetic properties.

Obtaining beta phase in Ti through processing in high energy mill powders of Ti and Nb

International Nuclear Information System (INIS)

Milanez, Mateus; Ferretto, Aline; Rocha, Marcio Roberto da; Arnt, Angela Coelho; Milanez, Alexandre; Schaeffer, Lirio

2014-01-01

An orthopedic implant, ideal, must meet the requirements of biocompatibility, have good mechanical properties among others. Titanium and Niobium exhibit biocompatibility and the β-Ti phase relationships have the highest strength / weight among all titanium alloys, presenting lower values of elastic modulus. The alloy has mechanically produced specific microstructural characteristics and improved mechanical properties compared with conventional powder metallurgy. In this study, a titanium alloy with different additions of niobium was used. The metal powders were mixed via mechanical alloy in high energy mill (attritor). The powder samples were analyzed by X-ray diffraction (X-RD) and property held by adhesive wear testing with a Pin-on-Disk. The present study revealed that through the high-energy milling is possible the atomic interaction between Ti and Nb particles and the mechanical properties are affected by the concentration of Nb. (author)

Cold compaction behavior of nano-structured Nd–Fe–B alloy powders prepared by different processes

International Nuclear Information System (INIS)

Liu, Xiaoya; Hu, Lianxi; Wang, Erde

2013-01-01

Graphical abstract: Relative density enhancement and nanocrystallization of Nd 2 Fe 14 B phase are two major effective means to improve magnetic properties. Since the matrix Nd 2 Fe 14 B phase in the starting Nd–Fe–B alloy can be disproportionated into a nano-structured mixture of NdH 2.7 , Fe 2 B, and α-Fe phases during mechanical milling in hydrogen. It is thus important to study the densification behavior of nanocrystalline powders to evaluate and predict the cold compactibility of powders. By comparison with the as milled as well as melt-spun Nd 16 Fe 76 B 8 alloy powders, we find that the as-disproportionated Nd 16 Fe 76 B 8 alloy powder exhibits the best cold compactibility. As evident from the illustration presented below, compaction parameters (representing the powder compactibility) have been determined by fitting density–pressure data with double logarithm compaction equation. Densification mechanisms involved during cold compaction process are clarified in our work by referring to microstructure observation of samples prepared by various methods. As a result, highly densified green magnet compact can be obtained by cold pressing of as-disproportionated NdFeB alloy powders. Highlights: ► Nano-structured disproportionated Nd–Fe–B alloy powders by mechanical milling in hydrogen. ► Highly densified green magnet compact by cold pressing of as-disproportionated Nd–Fe–B alloy powders. ► Density–pressure data fitted well by an empirical powder compaction model. ► As-disproportionated powder showed better compactibility than as milled and melt-spun counterparts. ► The effects of physical properties on powder compactibility and densification mechanisms are clarified. - Abstract: The compaction behavior of nano-structured Nd 16 Fe 76 B 8 (atomic ratio) alloy powders, which were prepared by three different processing routes including melt spinning, mechanical milling in argon, and mechanically activated disproportionation by milling in

Nanocrystallite characterization of milled simulated dry process fuel powders by neutron diffraction

International Nuclear Information System (INIS)

Ryu, Ho Jin; Kang, Kwon Ho; Moon, Je Sun; Song, Kee Chan; Choi, Yong Nam

2003-01-01

The nano-scale crystallite sizes of simulated spent fuel powders were measured by the neutron diffraction line broadening method in order to analyze the sintering behavior of the dry process fuel. The mixed U0 2 and fission product oxide powders were dry-milled in an attritor for 30, 60, and 120 min. The diffraction patterns of the powders were obtained by using the high resolution powder diffractometer in the HANARO research reactor. Diffraction line broadening due to crystallite size was measured using various techniques such as the Stokes' deconvolution, profile fitting methods using Cauchy function, Gaussian function, and Voigt function, and the Warren-Averbach method. The r.m.s. strain, stacking fault, twin and dislocation density were measured using the information from the diffraction pattern. The realistic crystallite size can be obtained after separation of the contribution from the non-uniform strain, stacking fault and twin

Polarization-dependent NEXAFS study of adsorption of long-chain surfactants on mechanically milled iron powder

Energy Technology Data Exchange (ETDEWEB)

Syugaev, A.V., E-mail: syual@mail.ru; Maratkanova, A.N.

2014-08-15

Highlights: • Plate-like particles modified with surfactant molecules were obtained under high-energy ball milling. • Adsorption layers were studied with polarization-dependent NEXAFS spectroscopy. • For the first time, arrangement of surfactants molecules on the powdered metal surface has been determined. • Tails of surfactant molecules (C-F/C-H) are shown to be oriented perpendicular to the particle surface. • Arrangement of carboxylate groups on the particle surfaces is discussed. - Abstract: In this work we have demonstrated the possibility of using the polarization-dependent NEXAFS spectra to study the structure of organic layers at the surface of powdered materials with plate-like shaped particles. The polarization dependence of the NEXAFS spectra may be easily obtained by just changing the angle between the X-ray beam direction and the substrate onto which the powder particles are set. For the first time, we have carried out a detailed study of the surfactant layers (n-perfluorononanoic and stearic acid), which are formed at the surface of iron plate-like particles under mechanical milling of iron powder with an addition of corresponding surfactants. The surfactant molecules are predominantly oriented perpendicular to the surface of the mechanically milled particles. Such orientation is similar to the arrangement of the molecules in the layers formed under equilibrium conditions, e.g. deposition from solutions. The changes in the chemical environment occurring in the molecule tails (defluorination or dehydrogenation) under mechanochemical treatment, do not result in a significant change in the molecular orientation and disordering of the adsorbed layer.

Synthesis and characterization of FePt nanoparticles by high energy ball milling with and without surfactant

International Nuclear Information System (INIS)

Velasco, V.; Martinez, A.; Recio, J.; Hernando, A.; Crespo, P.

2012-01-01

Highlights: ► Fe and Pt powders in the presence of surfactants don’t alloyed by HEBM technique. ► FePt alloys obtained by dry milling exhibit particle sizes of around 10 μm. ► FePt alloys obtained by dry milling exhibit soft magnetic behavior. ► A thermal treatment induces a phase transformation from FCC to FCT. - Abstract: FePt nanoparticles were prepared by high energy ball milling (HEBM) in two different ways. In the first one, elemental powders were mixed and milled whereas in the second one the milling was performed in the presence of oleyl amine and oleic acid as surfactants and hexane as a solvent. X-ray diffraction shows that when the milling is performed in dry conditions, Fe and Pt are alloyed after 5 h, whereas in the wet milling procedure alloying does not take place. In the first case, the diffraction pattern corresponds to the disordered FCC phase. This behavior is also corroborated by the evolution of the magnetic characteristics. In the case of the alloy obtained in dry conditions, the powder was heat treated in order to induce the transformation to the ordered phase. Coercivities of 2.5 kOe are obtained after 650 °C for 2 h.

Comparison of Magnetic Characteristics of Powder Magnetic Core and Evaluation of Motor Characteristics

Science.gov (United States)

Enomoto, Yuji; Ito, Motoya; Masaki, Ryozo; Yamazaki, Katsuyuki; Asaka, Kazuo; Ishihara, Chio; Ohiwa, Syoji

A magnetic characteristic measurement, a motor characteristic forecast, and an experimental evaluation of various powder magnetic cores were performed aiming at a fixed quantity grasp when the powder magnetic core was applied to the motor core as the magnetic material. The manufacturing conditions were changed, and magnetic characteristic compares a direct current magnetization characteristic and an iron disadvantageous characteristic with the silicon steel board for a different powder magnetic core. Therefore, though some permeabilities are low, characteristics almost equal to those of a silicon steel board were obtained in the maximum saturation magnetic induction, which confirms that the powder magnetic core in disadvantageous iron in a certain frequency domain, and to confirm disadvantageous iron lowers. Moreover, it has been shown to obtain characteristics almost equal to the silicon steel board when compared in terms of motor efficiency, though some disadvantageous iron increases since the effect when applying to the motor is verified the silicon steel board and the comparison evaluation for the surface type permanent magnet motor.

Transforming from paramagnetism to room temperature ferromagnetism in CuO by ball milling

Directory of Open Access Journals (Sweden)

Daqiang Gao

2011-12-01

Full Text Available In this work, we experimentally demonstrate that it is possible to induce ferromagnetism in CuO by ball milling without any ferromagnetic dopant. The magnetic measurements indicate that paramagnetic CuO is driven to the ferromagnetic state at room temperature by ball milling gradually. The saturation magnetization of the milled powders is found to increase with expanding the milling time and then decrease by annealing under atmosphere. The fitted X-ray photoelectron spectroscopy results indicate that the observed induction and weaken of the ferromagnetism shows close relationship with the valence charged oxygen vacancies (Cu1+-VO in CuO.

Properties of magnetic nickel/porous-silicon composite powders

Directory of Open Access Journals (Sweden)

Toshihiro Nakamura

2012-09-01

Full Text Available The magnetic and photoluminescence (PL properties of nickel/porous-silicon (Ni/PSi composite powders are investigated. Ni/PSi composite powders are prepared by stain etching of Si powder in a HF/HNO3 solution followed by electroless plating of Ni nanoparticles on the stain-etched PSi powder in a NiCl2 solution. The Ni/PSi powders exhibit hydrophillicity, superparamagnetism caused by the deposited Ni nanoparticles, and orange-red PL owing to the nanostructured PSi surface. The degree of magnetization decreases with increasing Ni plating time, indicating its dependence on the size of the Ni nanoparticles. The Ni/PSi composite powders also show a stronger magnetization as compared to that of the Ni-particle-plated Si powder. The stronger magnetization results from the larger surface area of PSi. The PL intensity, peak wavelength, and lifetime of Ni/PSi are strongly dependent on the NiCl2 concentration. This dependence is due to the different thickness of the oxide overlayer on the PSi surface formed during the Ni plating process. The existence of the oxide overlayer also results in a small change in the PL intensity against excitation time.

Cold compaction behavior of nano-structured Nd-Fe-B alloy powders prepared by different processes

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiaoya [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Hu, Lianxi, E-mail: hulx@hit.edu.cn [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Wang, Erde [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China)

2013-02-25

Graphical abstract: Relative density enhancement and nanocrystallization of Nd{sub 2}Fe{sub 14}B phase are two major effective means to improve magnetic properties. Since the matrix Nd{sub 2}Fe{sub 14}B phase in the starting Nd-Fe-B alloy can be disproportionated into a nano-structured mixture of NdH{sub 2.7}, Fe{sub 2}B, and {alpha}-Fe phases during mechanical milling in hydrogen. It is thus important to study the densification behavior of nanocrystalline powders to evaluate and predict the cold compactibility of powders. By comparison with the as milled as well as melt-spun Nd{sub 16}Fe{sub 76}B{sub 8} alloy powders, we find that the as-disproportionated Nd{sub 16}Fe{sub 76}B{sub 8} alloy powder exhibits the best cold compactibility. As evident from the illustration presented below, compaction parameters (representing the powder compactibility) have been determined by fitting density-pressure data with double logarithm compaction equation. Densification mechanisms involved during cold compaction process are clarified in our work by referring to microstructure observation of samples prepared by various methods. As a result, highly densified green magnet compact can be obtained by cold pressing of as-disproportionated NdFeB alloy powders. Highlights: Black-Right-Pointing-Pointer Nano-structured disproportionated Nd-Fe-B alloy powders by mechanical milling in hydrogen. Black-Right-Pointing-Pointer Highly densified green magnet compact by cold pressing of as-disproportionated Nd-Fe-B alloy powders. Black-Right-Pointing-Pointer Density-pressure data fitted well by an empirical powder compaction model. Black-Right-Pointing-Pointer As-disproportionated powder showed better compactibility than as milled and melt-spun counterparts. Black-Right-Pointing-Pointer The effects of physical properties on powder compactibility and densification mechanisms are clarified. - Abstract: The compaction behavior of nano-structured Nd{sub 16}Fe{sub 76}B{sub 8} (atomic ratio) alloy

Milling and Drilling Evaluation of Stainless Steel Powder Metallurgy Alloys

Energy Technology Data Exchange (ETDEWEB)

Lazarus, L.J.

2001-12-10

Near-net-shape components can be made with powder metallurgy (PM) processes. Only secondary operations such as milling and drilling are required to complete these components. In the past and currently production components are made from powder metallurgy (PM) stainless steel alloys. process engineers are unfamiliar with the difference in machining properties of wrought versus PM alloys and have had to make parts to develop the machining parameters. Design engineers are not generally aware that some PM alloy variations can be furnished with machining additives that greatly increase tool life. Specimens from a MANTEC PM alloy property study were made available. This study was undertaken to determine the machining properties of a number of stainless steel wrought and PM alloys under the same conditions so that comparisons of their machining properties could be made and relative tool life determined.

Structural and magnetic properties of Fe60Al40 alloys prepared by means of a magnetic mill

International Nuclear Information System (INIS)

Bernal-Correa, R.; Rosales-Rivera, A.; Pineda-Gomez, P.; Salazar, N.A.

2010-01-01

A study on synthesis, structural and magnetic characterization of Fe 60 Al 40 (at.%) alloys prepared by means of mechanical alloying process is presented. The mechanical alloying was performed using a milling device with magnetically controlled ball movement (Uni-Ball-Mill 5 equipment) at several milling times. The characterization was carried out via X-ray diffraction (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). The effects of milling time on the structural state, morphological evolution and magnetic behaviour of the Fe 60 Al 40 (at.%) alloys are discussed. Besides, in this current study we emphasize the result that indicating a ferro-para-ferromagnetic transition from a correlation between X-ray diffraction and magnetization data.

Low-temperature magnetic behavior of ball-milled copper ferrite

DEFF Research Database (Denmark)

Goya, G.F.; Rechenberg, H.R.; Jiang, Jianzhong

1999-01-01

We present a study on magnetic properties of CuFe2O4 nanoparticles, produced by high-energy ball milling. The series of samples obtained, with average particle sizes LFAN alpha d RTAN ranging from 61 nm to 9 nm, display increasing relaxation effects at room temperature. Irreversibility of the mag......We present a study on magnetic properties of CuFe2O4 nanoparticles, produced by high-energy ball milling. The series of samples obtained, with average particle sizes LFAN alpha d RTAN ranging from 61 nm to 9 nm, display increasing relaxation effects at room temperature. Irreversibility...... of the magnetization and shifts to negative fields in the hysteresis loops are observed below T-f APEQ 55 K, indicating unidirectional magnetic anisotropy in milled samples. These features could be explained by assuming the formation of a spin-disordered surface layer, which is exchange-coupled to the ferrimagnetic...

Synthesis and characterization of FePt nanoparticles by high energy ball milling with and without surfactant

Energy Technology Data Exchange (ETDEWEB)

Velasco, V., E-mail: vvjimeno@fis.ucm.es [Instituto de Magnetismo Aplicado, UCM-ADIF-CSIC, 28230 Las Rozas (Spain); Martinez, A.; Recio, J. [Instituto de Magnetismo Aplicado, UCM-ADIF-CSIC, 28230 Las Rozas (Spain); Hernando, A.; Crespo, P. [Instituto de Magnetismo Aplicado, UCM-ADIF-CSIC, 28230 Las Rozas (Spain); Dpto. de Fisica de Materiales, UCM, 28040 Madrid (Spain)

2012-09-25

Highlights: Black-Right-Pointing-Pointer Fe and Pt powders in the presence of surfactants don't alloyed by HEBM technique. Black-Right-Pointing-Pointer FePt alloys obtained by dry milling exhibit particle sizes of around 10 {mu}m. Black-Right-Pointing-Pointer FePt alloys obtained by dry milling exhibit soft magnetic behavior. Black-Right-Pointing-Pointer A thermal treatment induces a phase transformation from FCC to FCT. - Abstract: FePt nanoparticles were prepared by high energy ball milling (HEBM) in two different ways. In the first one, elemental powders were mixed and milled whereas in the second one the milling was performed in the presence of oleyl amine and oleic acid as surfactants and hexane as a solvent. X-ray diffraction shows that when the milling is performed in dry conditions, Fe and Pt are alloyed after 5 h, whereas in the wet milling procedure alloying does not take place. In the first case, the diffraction pattern corresponds to the disordered FCC phase. This behavior is also corroborated by the evolution of the magnetic characteristics. In the case of the alloy obtained in dry conditions, the powder was heat treated in order to induce the transformation to the ordered phase. Coercivities of 2.5 kOe are obtained after 650 Degree-Sign C for 2 h.

XRD analysis and microstructure of milled and sintered V, W, C, and Co powders

CSIR Research Space (South Africa)

Bolokang, AS

2011-01-01

Full Text Available on the starting compositions of pure elements, their lattice coherency according to Hume-Rothery rules on crystal structure and atomic size, and enough milling time that provides adequate kinetics. Keywords ? X-ray analysis; ? (V,W)C; ? Co15W8C6...-1 International Journal of Refractory Metals and Hard Materials Volume 29, Issue 1, January 2011, Pages 108?111 XRD analysis and microstructure of milled and sintered V, W, C, and Co powders ? A.S. Bolokang ? M.J. Phasha ? C. Oliphant ? D. Motaung ? a...

Effect of additives on the orientation of magnetic Sr-ferrite powders in powder injection molded compacts

Energy Technology Data Exchange (ETDEWEB)

Cho, T.S. [Sangju National Unviersity, Sangju (Korea); Jeung, W.Y. [Korea Institute of Science and Technology, Seoul (Korea)

2001-03-01

The effect of additives on the orientation of magnetic Sr-ferrite powders has been studied during powder injection molding under applied magnetic field for fabricating multi=pole anisotropic sintered Sr-ferrite magnets. The orientation of the Sr-ferrite powders depends sensitively on the fluidity of powder-binder mixture, related to the binder additives and the injection molding temperature, and the magnetic field intensity. The orientation of Sr-ferrite powders is good for the compacts with stearic acid added in the binder system of paraffin wax/ carnauba wax/HDPE, but it is poor of the compacts with silane coupling agent added. The orientation of sr-ferrites higher than 80% is achieved at the following useful conditions; apparent viscosity lower than 2500 poise in 1000 sec {sup -1} shear rate and applied magnetic field higher than 4 kOe. (author). 15 refs., 1 tab., 6 figs.

Joining of parts via magnetic heating of metal aluminum powders

Science.gov (United States)

Baker, Ian

2013-05-21

A method of joining at least two parts includes steps of dispersing a joining material comprising a multi-phase magnetic metal-aluminum powder at an interface between the at least two parts to be joined and applying an alternating magnetic field (AMF). The AMF has a magnetic field strength and frequency suitable for inducing magnetic hysteresis losses in the metal-aluminum powder and is applied for a period that raises temperature of the metal-aluminum powder to an exothermic transformation temperature. At the exothermic transformation temperature, the metal-aluminum powder melts and resolidifies as a metal aluminide solid having a non-magnetic configuration.

Effect of high energy milling time of the aluminum bronze alloy obtained by powder metallurgy with niobium carbide addition

Energy Technology Data Exchange (ETDEWEB)

Dias, Alexandre Nogueira Ottoboni; Silva, Aline da; Rodrigues, Carlos Alberto; Melo, Mirian de Lourdes Noronha Motta; Rodrigues, Geovani; Silva, Gilbert, E-mail: aottoboni@yahoo.com.br [Universidade Federal de Itajuba (UNIFEI), Itajuba, MG (Brazil)

2017-05-15

The aluminum bronze alloy is part of a class of highly reliable materials due to high mechanical strength and corrosion resistance being used in the aerospace and shipbuilding industry. It's machined to produce parts and after its use cycle, it's discarded, but third process is considered expensive and besides not being correct for environment reasons. Thus, reusing this material through the powder metallurgy (PM) route is considered advantageous. The aluminum bronze chips were submitted to high energy ball milling process with 3% of niobium carbide (NbC) addition. The NbC is a metal-ceramic composite with a ductile-brittle behaviour. It was analyzed the morphology of powders by scanning electron microscopy as well as particle size it was determined. X ray diffraction identified the phases and the influence of milling time in the diffractogram patterns. Results indicates that milling time and NbC addition improves the milling efficiency significantly and being possible to obtain nanoparticles. (author)

Perovskite nanoparticles: Preparation by reactive milling and magnetic characteristics

International Nuclear Information System (INIS)

Phuc, N.X.; Nguyen, Ha M.; Manh, D.H.; Hung, L.T.; Tuong, L.T.C.; Hong, L.V.; Yao, Yeong-Der

2006-01-01

La 0.7 Sr 0.3 MnO 3 and La 0.7 Ca 0.3 MnO 3 nanoparticles were synthesized by reactive milling method. Grain size determined from XRD, TEM, and magnetization measurements show an average diameter ≤18 nm and decreasing with increasing milling time. DC and AC magnetic measurements evidenced an interacting superparamagnetism due to clustering of perovskite nanoferromagnets with spin dynamic time in range of 10 -9 -10 -10 s

Powder metallurgical processing of magnetostrictive materials based on rare earth-iron intermetallic compounds

International Nuclear Information System (INIS)

Malekzadeh, M.

1978-01-01

Procedures are described for fabrication of high density rare earth-iron magnetostrictive compounds by powder metallurgical techniques. The fabrication involves a sequence of steps which includes preparing the pre-alloyed compounds, pulverizing them into a fine powder, compacting in suitable sizes and shapes, and sintering. Samples prepared by these procedures are carefully characterized by scanning electron microscopy, x-ray diffraction, dilatometry, and magnetic measurements. Process steps are found to exert important influences upon densities, microstructure and magnetic properties attained after densification. Investigations on a number of these process steps, including milling time and medium, sintering, and magnetic powder alignment are described

Application of permanent magnets made from NdFeB powder and from mixtures of powders in DC motors

International Nuclear Information System (INIS)

Slusarek, B.; Dudzikowski, I.

2002-01-01

The paper presents the influence of magnetic properties of applied permanent magnets on the characteristics of DC motors excited with these magnets. In the factory-produced DC motors, excited with sintered ferrite magnets, authors replaced ferrite magnets with the dielectromagnets from NdFeB powder and from different mixtures of NdFeB and ferrite powders. The paper shows the increase of the power of the resultant DC motors according to the powders' content

Liquid coated melt-spun Nd-Fe-B powders for bonded magnets

Science.gov (United States)

Li, D.; Gaiffi, S.; Kirk, D.; Young, K.; Herchenroeder, J.; Berwald, T.

1999-04-01

The liquid coating (LC) has been employed to apply epoxy and lubricant over the surface of rapidly solidified Nd-Fe-B powder particles. The LC led to an improvement of physical and magnetic properties for the powders and magnets compared to the dry blending and the encapsulation methods. The LC powders have excellent flowability and can be used for bonded magnets requiring very close tolerances; further bonded magnets made using this powder posses higher strength.

Preparation of strontium hexaferrite magnets from celestite and blue dust by mechanochemical route

Directory of Open Access Journals (Sweden)

Tiwary R.K.

2008-01-01

Full Text Available In the present investigation celestite (natural ore of strontium and blue dust (iron ore fines have been used for the preparation of strontium hexaferrite powder. The mechanical alloying process has been adopted to prepare strontium hexaferrite powder. The celestite after chemical upradation and physically upgraded blue dust alongwith sodium carbonate was taken for the preparation of strontium hexaferrite in this experiment. The high-energy planetary ball mill with tungsten carbide jar and ball was used to prepare strontium hexaferrite powder. A long time of ball milling for different duration has led to displacement solid-state reaction. At the end of each experiment the product was washed thoroughly and dried. The X-ray diffaction study after annealing shows the development of single-phase strontium hexaferrite after 40 hrs. of milling. The resultant powder was compacted under magnetic field and sintered to prepare the magnet after annealing the ferrite powder. The magnetic properties were measured by Pulse magneto meter. The moderate value of coercivity, remanence and energy product were observed in this sintered magnet. The work illustrates the feasibility to prepare strontium hexaferrite magnetic powders directly from natural ores which can reduce the total cost of production as compared to conventional method.

Magnetic and mechanical properties of Cu (75 wt%) – 316L grade stainless steels synthesized by ball milling and annealing

Energy Technology Data Exchange (ETDEWEB)

Mondal, Bholanath, E-mail: bholanath_mondal@yahoo.co.in [Department of Central Scientific Services, Indian Association for the Cultivation of Science, Jadavpur, Kolkata 700032 (India); Chabri, Sumit [Department of Metallurgy and Materials Engineering, Indian Institute of Engineering Science and Technology, Shibpur, Howrah 711103 (India); Sardar, Gargi [Department of Zoology, Baruipur College, South 24 Parganas, 743610 (India); Bhowmik, Nandagopal [Department of Metallurgy and Materials Engineering, Indian Institute of Engineering Science and Technology, Shibpur, Howrah 711103 (India); Sinha, Arijit, E-mail: arijitsinha2@yahoo.co.in [School of Materials Science and Engineering, Indian Institute of Engineering Science and Technology, Shibpur, Howrah 711103 (India); Chattopadhyay, Partha Protim [Department of Metallurgy and Materials Engineering, Indian Institute of Engineering Science and Technology, Shibpur, Howrah 711103 (India)

2015-05-01

Elemental powders of Cu (75 wt%) and 316-stainless steel (25 wt%) has been subjected to ball milling upto 70 h followed by isothermal annealing at the temperature range of 350–750 °C for 1 h to investigate the microstructural evolution along with magnetic and mechanical properties. After 40 h of milling, the bcc Fe is almost dissolved in the solid solution of Cu but no significant change has been observed in the XRD pattern after 70 h of milling, Annealing of the alloy has resulted in precipitation of nanocrystalline bcc-Fe in Cu which triggers the soft ferromagnetic properties. The extensive mechanical characterization has been done at the microstructural scale by nanoindentation technique which demonstrates a hardening behavior of the compacted and annealed alloys due to possible precipitation of nanocrystalline bcc-Fe in Cu. - Highlights: • Nanocrystalline phases with partial amorphorization obtained after 70 h of milling. • Precipitation and grain coarsening of Fe and Cu after annealing as observed by XRD. • Annealing of the ball milled sample upto 550 {sup o}C has evolved ferromagnetic behavior. • Nanoindentation predicts a hardening behavior of annealed ball milled samples.

Processing of magnetically anisotropic MnBi particles by surfactant assisted ball milling

Energy Technology Data Exchange (ETDEWEB)

Kanari, K. [Department of Physics, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece); Sarafidis, C., E-mail: hsara@physics.auth.gr [Department of Physics, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece); Gjoka, M.; Niarchos, D. [INN, NCSR Demokritos, Athens 15310 (Greece); Kalogirou, O. [Department of Physics, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece)

2017-03-15

MnBi particles are obtained from bulk MnBi using mechanochemical processing. The structure and magnetic properties of the MnBi particles are investigated by means of X-ray diffraction analysis, scanning electron microscopy and magnetometry. Surfactant assisted high energy ball milling results to the samples’ degradation even after one hour of milling. In the case of surfactant assisted low energy ball milling the increase of ball milling duration decreases the average particle size while the particles seem to be more separated. The saturation magnetization (M{sub s}) was found to decrease for large milling times beginning from 61 Am{sup 2}/kg, while the coercivity (μ{sub 0}H{sub c}) increases with the increase of ball milling duration up to 35 min where it reaches 1.62 T and thereafter it decreases. - Highlights: • Effect of surfactants in processing of MnBi. • Magnetization degradation due to air storage and due to processing. • Coercivity of 1.6 T in epoxy resin oriented material.

Spark-plasma sintering and mechanical property of mechanically alloyed NiAl powder compact and ball-milled (Ni+Al) mixed powder compact

International Nuclear Information System (INIS)

Kim, J.S.; Jang, Y.I.; Kwon, Y.S.; Kim, Y.D.; Ahn, I.S.

2001-01-01

Mechanically-alloyed NiAl powder and (Ni+Al) powder mixture prepared by ball-milling were sintered by spark-plasma sintering (SPS) process. Densification behavior and mechanical property were determined from the experimental results and analysis such as changes in linear shrinkage, shrinkage rate, microstructure, and phase during sintering process, Vicker's hardness and transverse rupture strength tests. Densification mechanisms for MA-NiAl powder compact and (Ni+Al) powder mixture were different from each other. While the former showed a rapid increase in densification rate only at higher temperature region of 800-900 o C, the latter revealed firstly a rapid increase in densification rate even at low temperature of 300 o C and a subsequent increase up to 500 o C. Densities of both powder compact (MA and mixture) sintered at 1150 o C for 5 min were 98 and above 99 %, respectively. Sintered bodies were composed mainly of NiAl phase with Ni 3 Al as secondary phase for both powders. Sintered body of MA-NiAl powder showed a very fine grain structure. Crystallite size determined by XRD result and the Sherrer's equation was approximately 80 nm. Vicker's hardness for the sintered bodies of (Ni+Al) powder mixture and MA-NiAl powder were 410±12 H v and 555±10 H v , respectively, whereas TRS values 1097±48 MPa and 1393±75 MPa. (author)

Structural and magnetic studies on spark plasma sintered SmCo{sub 5}/Fe bulk nanocomposite magnets

Energy Technology Data Exchange (ETDEWEB)

Rama Rao, N.V. [Defence Metallurgical Research Laboratory, Hyderabad 500 058 (India); Gopalan, R. [Defence Metallurgical Research Laboratory, Hyderabad 500 058 (India)]. E-mail: rg_gopy@yahoo.com; Manivel Raja, M. [Defence Metallurgical Research Laboratory, Hyderabad 500 058 (India); Chandrasekaran, V. [Defence Metallurgical Research Laboratory, Hyderabad 500 058 (India); Chakravarty, D. [International Advanced Research Centre for Powder Metallurgy and New Materials, Hyderabad 500 005 (India); Sundaresan, R. [International Advanced Research Centre for Powder Metallurgy and New Materials, Hyderabad 500 005 (India); Ranganathan, R. [Saha Institute of Nuclear Physics, Kolkata 700 064 (India); Hono, K. [National Institute for Materials Science, 1-2-1 Sengen, Tsukuba 305 0047 (Japan)

2007-05-15

SmCo{sub 5}+xwt% Fe (x=0, 5 and 10) nanocomposite powders were synthesized by mechanical milling and were consolidated into bulk shape by spark plasma sintering (SPS) technique. The evolution of structure and magnetic properties were systematically investigated in milled powders as well as in SPS samples. A maximum coercivity of 8.9kOe was achieved in spark plasma sintered SmCo{sub 5}+5wt% Fe sample. The exchange spring interaction between the hard and soft magnetic phases was evaluated using {delta}M-H measurements and the analysis revealed that the SPS sample containing 5wt% Fe had a stronger exchange coupling between the magnetic phases than that of the sample with10wt% Fe.

Hyperfine interactions and structural features of Fe–44Co–6Mo (wt.%) nanostructured powders

International Nuclear Information System (INIS)

Moumeni, Hayet; Nemamcha, Abderrafik; Alleg, Safia; Grenèche, Jean Marc

2013-01-01

Nanocrystalline Fe–44Co–6Mo (wt.%) powders have been prepared by high-energy ball milling from elemental Fe, Co and Mo pure powders in a P7 planetary ball mill. The obtained powders were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Mössbauer spectrometry techniques. The influence of milling process and Mo substitution for Co in equiatomic FeCo have been examined in order to study structural evolution and formation mechanism of nanostructured Fe(CoMo) solid solution. XRD results show the formation of a BCC Fe(CoMo) solid solution (a = 0.2874 nm) where unmixed nanocrystalline Mo with a BCC structure is embedded. Disordered Fe(CoMo) solid solution is characterized by a broad hyperfine magnetic field distribution with two regions centered at B 1 = 35.0 T and B 2 = 30.7 T, respectively, attributed to disordered Fe(Co) solid solution and CoMo enriched environments. Prolonged milling and Mo addition cause the decrease of average hyperfine magnetic field while the average isomer shift remains nearly constant. - Highlights: ► BCC nanostructured Fe(CoMo) solid solution is prepared by milling of Fe, Co and Mo. ► Formation mechanism: Co diffusion into Fe lattice and Mo dissolution in Fe(Co). ► Crystallite size of Fe(CoMo) solid solution reaches 11 nm after 24 h of milling. ► Mössbauer analysis reveals 3 components: high field, enriched Co and low field

Hyperfine interactions and structural features of Fe–44Co–6Mo (wt.%) nanostructured powders

Energy Technology Data Exchange (ETDEWEB)

Moumeni, Hayet, E-mail: hmoumeni@yahoo.fr [Laboratoire de Chimie Computationnelle et Nanostructures, Département des Sciences de la Matière, Faculté des Mathématiques et de l' Informatique et des Sciences de la Matière, Université 08 Mai 1945 - Guelma, B.P. 401, Guelma 24000 (Algeria); Nemamcha, Abderrafik [Laboratoire d' Analyses Industrielles et Génie des Matériaux, Faculté des Sciences et de la Technologie, Université 08 Mai 1945 - Guelma, B.P. 401, Guelma 24000 (Algeria); Alleg, Safia [Laboratoire de Magnétisme et de Spectroscopie des Solides, Département de Physique, Faculté des Sciences, Université de Annaba, B.P. 12, Annaba 23000 (Algeria); Grenèche, Jean Marc [Laboratoire de Physique de l' Etat Condensé, UMR CNRS 6087, Institut de Recherche en Ingénierie Moléculaire et Matériaux Fonctionnels IRIM2F, FR CNRS 2575, Université du Maine, 72085 Le Mans Cedex 9 (France)

2013-02-15

Nanocrystalline Fe–44Co–6Mo (wt.%) powders have been prepared by high-energy ball milling from elemental Fe, Co and Mo pure powders in a P7 planetary ball mill. The obtained powders were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Mössbauer spectrometry techniques. The influence of milling process and Mo substitution for Co in equiatomic FeCo have been examined in order to study structural evolution and formation mechanism of nanostructured Fe(CoMo) solid solution. XRD results show the formation of a BCC Fe(CoMo) solid solution (a = 0.2874 nm) where unmixed nanocrystalline Mo with a BCC structure is embedded. Disordered Fe(CoMo) solid solution is characterized by a broad hyperfine magnetic field distribution with two regions centered at B{sub 1} = 35.0 T and B{sub 2} = 30.7 T, respectively, attributed to disordered Fe(Co) solid solution and CoMo enriched environments. Prolonged milling and Mo addition cause the decrease of average hyperfine magnetic field while the average isomer shift remains nearly constant. - Highlights: ► BCC nanostructured Fe(CoMo) solid solution is prepared by milling of Fe, Co and Mo. ► Formation mechanism: Co diffusion into Fe lattice and Mo dissolution in Fe(Co). ► Crystallite size of Fe(CoMo) solid solution reaches 11 nm after 24 h of milling. ► Mössbauer analysis reveals 3 components: high field, enriched Co and low field.

Crushing method for nuclear fuel powder

International Nuclear Information System (INIS)

Hasegawa, Shin-ichi; Tsuchiya, Haruo.

1997-01-01

A crushing medium is contained in mill pots disposed at the circumferential periphery of a main axis. The diameter of each mill pot is determined such that powdery nuclear fuels containing aggregated powders and ground and mixed powders do not reach criticality. A plurality of mill pots are revolved in the direction of the main axis while each pots rotating on its axis. Powdery nuclear fuels containing aggregated powders are conveyed to a supply portion of the moll pot, and an inert gas is supplied to the supply portion. The powdery nuclear fuels are supplied from the supply portion to the inside of the mill pots, and the powdery nuclear fuels containing aggregated powders are crushed by centrifugal force caused by the rotation and the revolving of the mill pots by means of the crushing medium. UO 2 powder in uranium oxide fuels can be crushed continuously. PuO 2 powder and UO 2 powder in MOX fuels can be crushed and mixed continuously. (I.N.)

Magnetoresistivity and microstructure of YBa2Cu3Oy prepared using planetary ball milling

International Nuclear Information System (INIS)

Hamrita, A.; Ben Azzouz, F.; Madani, A.; Ben Salem, M.

2012-01-01

Superconducting properties of YBa 2 Cu 3 O y prepared using planetary ball milling were studied. Y-deficient YBa 2 Cu 3 O y nanoparticles are embedded in the superconducting matrix. Ball milled sample exhibits a large magnetoresistivity in weak magnetic fields at 77 K. We have studied the microstructure and the magnetoresistivity of polycrystalline YBa 2 Cu 3 O y (YBCO or Y-123 for brevity) embedded with nanoparticles of Y-deficient YBCO, generated by the planetary ball milling technique. Bulk samples were synthesized from a precursor YBCO powder, which was prepared from commercial high purity Y 2 O 3 , Ba 2 CO 3 and CuO via a one-step annealing process in air at 950 °C. After planetary ball milling of the precursor, the powder was uniaxially pressed and subsequently annealed at 950 °C in air. Phase analysis by X-ray diffraction (XRD), granular structure examination by scanning electron microscopy (SEM), microstructure investigation by transmission electron microscopy (TEM) coupled with energy dispersive X-ray spectroscopy (EDXS) were carried out. TEM analyses show that nanoparticles of Y-deficient YBCO, generated by ball milling, are embedded in the superconducting matrix. Electrical resistance as a function of temperature, ρ(T), revealed that the zero resistance temperature, T co , is 84.5 and 90 K for the milled and unmilled samples respectively. The milled ceramics exhibit a large magnetoresistance in weak magnetic fields at liquid nitrogen temperature. This attractive effect is of high significance as it makes these materials promising candidates for practical application in magnetic field sensor devices.

Effect of process control agent on the structural and magnetic properties of nano/amorphous Fe0.7Nb0.1Zr0.1Ti0.1 powders prepared by high energy ball milling

Science.gov (United States)

Khazaei Feizabad, Mohammad Hossein; Sharafi, Shahriar; Khayati, Gholam Reza; Ranjbar, Mohammad

2018-03-01

In this study, amorphous Fe0.7Nb0.1Zr0.1Ti0.1 alloy without metalloids was produced by mechanical alloying of pure mixture elements. Miedema's semi-empirical model was employed to predict the possibility of amorphous phase formation in proposed alloying system. The effect of Hexane as process control agent (PCA) on the structural, magnetic, morphological and thermal properties of the products was investigated. The results showed that the presence of PCA was necessary for the formation of amorphous phase as well as improved its soft magnetic properties. The PCA addition causes an increase of the saturation magnetization (about 43%) and decrease of the coercivity (about 50%). Moreover, the sample milled without PCA, showed a wide particle size distribution as well as relatively spherical geometry. While, in the presence of PCA the powders were aspherical and Polygon. In addition, the crystallization and Curie temperatures were found to be around 800 °C and 650 °C, respectively which are relatively high values for these kinds of alloys.

Structural and magnetic properties of Fe{sub 60}Al{sub 40} alloys prepared by means of a magnetic mill

Energy Technology Data Exchange (ETDEWEB)

Bernal-Correa, R. [Laboratorio de Magnetismo y Materiales Avanzados, Facultad de Ciencias Exactas y Naturales, Universidad Nacional de Colombia, Manizales (Colombia); Rosales-Rivera, A., E-mail: arosalesr@unal.edu.c [Laboratorio de Magnetismo y Materiales Avanzados, Facultad de Ciencias Exactas y Naturales, Universidad Nacional de Colombia, Manizales (Colombia); Pineda-Gomez, P. [Laboratorio de Magnetismo y Materiales Avanzados, Facultad de Ciencias Exactas y Naturales, Universidad Nacional de Colombia, Manizales (Colombia); Universidad de Caldas, Manizales (Colombia); Salazar, N.A. [Laboratorio de Magnetismo y Materiales Avanzados, Facultad de Ciencias Exactas y Naturales, Universidad Nacional de Colombia, Manizales (Colombia)

2010-04-16

A study on synthesis, structural and magnetic characterization of Fe{sub 60}Al{sub 40} (at.%) alloys prepared by means of mechanical alloying process is presented. The mechanical alloying was performed using a milling device with magnetically controlled ball movement (Uni-Ball-Mill 5 equipment) at several milling times. The characterization was carried out via X-ray diffraction (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). The effects of milling time on the structural state, morphological evolution and magnetic behaviour of the Fe{sub 60}Al{sub 40} (at.%) alloys are discussed. Besides, in this current study we emphasize the result that indicating a ferro-para-ferromagnetic transition from a correlation between X-ray diffraction and magnetization data.

Effect of milling time and annealing temperature on nanoparticles evolution for 13.5% Cr ODS ferritic steel powders by joint application of XAFS and TEM

Science.gov (United States)

He, P.; Hoffmann, J.; Möslang, A.

2018-04-01

The characteristics of strengthening nanoparticles have a major influence on the mechanical property and irradiation resistance of oxide dispersion strengthened (ODS) steels. To determine how to control nanoparticles evolution, 0.3% Ti with 0.3% Y2O3 were added in 13.5%Cr pre-alloyed steel powders via different milling and consolidation conditions, then characterized by transmission electron microscopy (TEM) and X-ray absorption fine structure (XAFS) at synchrotron irradiation facility. The dissolution of Y2O3 is greatly dependent on the milling time at fixed milling speeds. After 24 h of milling, only minor amounts of the initially added Y2O3 dissolve into the steel matrix whereas TEM results reveal nearly complete dissolution of Y2O3 in 80-h-milled powder. The annealed powder FT-A800 (at 800 °C for 1 h) exhibits a structure near to the initially added Y2O3. The slightly deviation may be accounted for considerable lattice distortion related to the presence of atomic vacancies or formation of Y-Ti-O nucleus. The annealed powders FT-A1000 and FT-A1100 contain complex mixtures of Y-O/Y-Ti-O oxides, which cannot be fitted by any single thermally stable compounds. The coordination numbers of these first two shells in the annealed powders significantly raise as a function of the annealing temperature, indicating the formation of more ordered Y-O or Y-Ti-O particles. The extended X-ray absorption fine structure (EXAFS) spectrum could not necessarily distinguish the dominant oxide species.

Polycrystalline Nd2Fe14B/α-Fe nanocomposite flakes with a sub-micro/nanometre thickness prepared by surfactant-assisted high-energy ball milling

International Nuclear Information System (INIS)

Tang, Xin; Chen, Xi; Chen, Renjie; Yan, Aru

2015-01-01

Highlights: • Nd 2 Fe 14 B/α-Fe flakes are formed by peeling along preferential planes. • (0 0 l) planes are found to be preferential cleavage planes. • Magnetic properties degrade with increasing ball milling time. • Anisotropic nanocomposite magnets are fabricated. - Abstract: A surfactant-assisted high-energy ball milling technique was employed to synthesize Nd 2 Fe 14 B/α-Fe nanoparticles and nanoflakes from melt-spun nanocrystalline powders. The microstructure evolution in ball milling process was investigated. In the beginning stage (0–4 h) of ball milling, raw powders were crushed into micrometre-sized particles. While flakes were mainly formed by reducing thickness of particles via peeling layer by layer along preferential planes in the late stage (8–16 h). The selected area electron diffraction and high-resolution transmission electron microscopy images show that preferential cleavage planes are basal planes. With ball milling proceeding, more and more defects were induced by ball milling. As a result, the coercivity and remanence decreased to 1.6 kOe and 3.2 kGs, respectively. After 16 h ball milling, the exchange decoupling occurred due to severe amorphorization. A weakly-textured nanocomposite magnet was fabricated after 12 h ball milling and the anisotropy in magnetic properties can be further improved by employing settling down process to select particle size and aligning particles in external field

Effect of annealing process of iron powder on magnetic properties ...

Indian Academy of Sciences (India)

Administrator

Abstract. Iron powder magnetic cores are used as soft magnetic rotors, in micro special motors such as BS brake motors, refrigerator compressor motors and brushless servo motors. Heat treatment of iron powder played an important role in the magnetic properties and loss of the motor cores. After the annealing process,.

Strain-enhanced sintering of iron powders

Energy Technology Data Exchange (ETDEWEB)

Amador, D.R.; Torralba, J.M. [Universidad Carlos III de Madrid, Departamento de Ciencias de Materiales e Ingenieria Metalurgica, Leganes, Madrid (Spain); Monge, M.A.; Pareja, R. [Universidad Carlos III de Madrid, Departamento de Fisica, Madrid (Spain)

2005-02-01

Sintering of ball-milled and un-milled Fe powders has been investigated using dilatometry, X-ray, density, and positron annihilation techniques. A considerable sintering enhancement is found in milled powders showing apparent activation energies that range between 0.44 and 0.80 eV/at. The positron annihilation results, combined with the evolution of the shrinkage rate with sintering temperature, indicate generation of lattice defects during the sintering process of milled and un-milled powders. The sintering enhancement is attributed to pipe diffusion along the core of moving dislocations in the presence of the vacancy excess produced by plastic deformation. Positron annihilation results do not reveal the presence of sintering-induced defects in un-milled powders sintered above 1200 K, the apparent activation energy being in good agreement with that for grain-boundary diffusion in {gamma}-Fe. (orig.)

Powder Neutron Diffraction and Magnetic structures

International Nuclear Information System (INIS)

Vigneron, F.

1986-01-01

The determination of the magnetic structures of materials (ferromagnetic, antiferromagnetic, helimagnetic, .) can be achieved only by neutron diffraction. A general survey of the powder technique is given: 2-axis spectrometer and analysis of the magnetic data. For the REBe/sb13/ intermetallic compounds (RE = Rare Earth), commensurate and/or incommensurate magnetic structures are observed and discussed as a function of RE (Gd, Tb, Dy, Ho, Er)

Electrochemical properties of the ball-milled LaMg10NiMn alloy with Ni powders

International Nuclear Information System (INIS)

Wang Yi; Wang Xin; Gao Xueping; Shen Panwen

2008-01-01

The electrochemical characteristics of the ball-milled LaMg 10 NiMn alloys with Ni powders were investigated. It was found that the ball-milled LaMg 10 NiMn + 150 wt.% Ni composite exhibited higher first discharge capacity and better cycle performance. By means of the analysis of electrochemical impedance spectra (EIS), it was shown that the existence of manganese in LaMg 10 NiMn alloy increased the electrocatalytic activity due to its catalytic effect, and destabilized metal hydrides, and so reduced the hydrogen diffusion resistance. These contributed to the higher discharge capacity of the ball-milled LaMg 10 NiMn-Ni composite. According to the analytical results of X-ray diffraction (XRD), EIS and steady-state polarization (SSP) experiments, the inhibition of metal corrosion is not the main reason for the better cycle performance. The main reason is that the electrochemical reaction resistance of the ball-milled LaMg 10 NiMn-Ni composite is always lower than that of the ball-milled LaMg 10 Ni 2 -Ni composite because the former one contains manganese, which is a catalyst for the electrode reaction

Magnetic modification of diamagnetic agglomerate forming powder materials

Czech Academy of Sciences Publication Activity Database

Šafařík, Ivo; Baldíková, Eva; Pospíšková, K.; Šafaříková, Miroslava

2016-01-01

Roč. 29, December (2016), s. 169-171 ISSN 1674-2001 Institutional support: RVO:60077344 Keywords : magnetic modification * magnetic separation * powdered material * magnetic iron oxide * microwave assisted synthesis Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.621, year: 2016

Novel Fe-based nanocrystalline powder cores with excellent magnetic properties produced using gas-atomized powder

Science.gov (United States)

Chang, Liang; Xie, Lei; Liu, Min; Li, Qiang; Dong, Yaqiang; Chang, Chuntao; Wang, Xin-Min; Inoue, Akihisa

2018-04-01

FeSiBPNbCu nanocrystalline powder cores (NPCs) with excellent magnetic properties were fabricated by cold-compaction of the gas-atomized amorphous powder. Upon annealing at the optimum temperature, the NPCs showed excellent magnetic properties, including high initial permeability of 88, high frequency stability up to 1 MHz with a constant value of 85, low core loss of 265 mW/cm3 at 100 kHz for Bm = 0.05 T, and superior DC-bias permeability of 60% at a bias field of 100 Oe. The excellent magnetic properties of the present NPCs could be attributed to the ultrafine α-Fe(Si) phase precipitated in the amorphous matrix and the use of gas-atomized powder coated with a uniform insulation layer.

New manufacturing method for Fe-Si magnetic powders using modified pack-cementation process

Science.gov (United States)

Byun, Ji Young; Kim, Jang Won; Han, Jeong Whan; Jang, Pyungwoo

2013-03-01

This paper describes a new method for making Fe-Si magnetic powders using a pack-cementation process. It was found that Fe-Si alloy powders were formed by a reaction of the pack mixture of Fe, Si, NaF, and Al2O3 powders at 900 °C for 24 h under a hydrogen atmosphere. Separation of the Fe-Si alloy powders was dependent on the particle size of the Fe powders in the pack. For small Fe powders, magnetic separation in a medium of strong alkali solution was recommended. But, for relatively larger Fe powders, the Fe-Si alloy powders were easily separated from Al2O3 powders using a magnet in air atmosphere. The Si content in the Fe-Si magnetic powders were easily controlled by changing the weight ratio of Si to (Si+Fe) in the pack.

Influence of octanoic acid on SmCo{sub 5} nanoflakes prepared by surfactant-assisted high-energy ball milling

Energy Technology Data Exchange (ETDEWEB)

Zheng Liyun, E-mail: zheng@udel.ed [Department of Physics and Astronomy, University of Delaware, Newark, DE 19716 (United States); College of Electromechanical Engineering, Hebei University of Engineering, Handan, Hebei 056038 (China); Cui Baozhi; Akdogan, Nilay G.; Li Wanfeng; Hadjipanayis, George C. [Department of Physics and Astronomy, University of Delaware, Newark, DE 19716 (United States)

2010-08-20

High-energy ball milling (HEBM) of magnetically hard SmCo{sub 5} was conducted in heptane with octanoic acid as the surfactant. The effects of octanoic acid on the morphology and magnetic properties of the powders were investigated by scanning electron microscopy, X-ray diffraction and vibrating sample magnetometry. The results show an interesting unexpected fact that the SmCo{sub 5} powders processed by octanoic acid-assisted HEBM were in form of nanoflakes with aspect-ratio of 10{sup 2}-10{sup 3} without the presence of nanoparticles. The thickness of nanoflakes decreases with increasing milling time. X-ray diffraction patterns did not show the sign of oxidation and the diffraction peaks of SmCo{sub 5} were getting broader with the increase of milling time. The nanoflakes were magnetically anisotropic and had a higher coercivity than the micro-particles prepared by HEBM without surfactant. The coercivity of SmCo{sub 5} increased initially with the milling time and then it decreased after reaching the maximum value of 15.2 kOe. High-resolution transmission electron microscopy image showed that the SmCo{sub 5} nanoflakes are nanocrystalline with an average crystallite size approximately 12 nm.

Developments with melt spun RE-Fe-B powder for bonded magnets

International Nuclear Information System (INIS)

Brown, D.N.; Chen, Z.; Guschl, P.; Campbell, P.

2006-01-01

Rapidly quenched isotropic rare earth iron boride (RE-Fe-B) powders have found many applications throughout the electronics, automotive and white goods industries. The magnetic performance, thermal stability, corrosion resistance and processability of a powder are important factors when selecting a RE-Fe-B powder for a particular application. For electronic devices that operate at ambient temperatures, high remanence (B r ) tends to be a priority and RE 2 Fe 14 B/α-Fe nanocomposite powder magnets are favoured. Alternatively, automotive applications tend to require greater thermal stability and corrosion resistance, which are satisfied by single-phase RE 2 Fe 14 B powder magnets with higher intrinsic coercivity (H ci ). This article reviews the performance of commercially available rapidly solidified RE-Fe-B powders and recent developments made to address the demands of applications

The Effect of Milling Time on the Microstructural Characteristics and Strengthening Mechanisms of NiMo-SiC Alloys Prepared via Powder Metallurgy

Science.gov (United States)

Yang, Chao; Muránsky, Ondrej; Zhu, Hanliang; Thorogood, Gordon J.; Avdeev, Maxim; Huang, Hefei; Zhou, Xingtai

2017-01-01

A new generation of alloys, which rely on a combination of various strengthening mechanisms, has been developed for application in molten salt nuclear reactors. In the current study, a battery of dispersion and precipitation-strengthened (DPS) NiMo-based alloys containing varying amounts of SiC (0.5–2.5 wt %) were prepared from Ni-Mo-SiC powder mixture via a mechanical alloying (MA) route followed by spark plasma sintering (SPS) and rapid cooling. Neutron Powder Diffraction (NPD), Electron Back Scattering Diffraction (EBSD), and Transmission Electron Microscopy (TEM) were employed in the characterization of the microstructural properties of these in-house prepared NiMo-SiC DPS alloys. The study showed that uniformly-dispersed SiC particles provide dispersion strengthening, the precipitation of nano-scale Ni3Si particles provides precipitation strengthening, and the solid-solution of Mo in the Ni matrix provides solid-solution strengthening. It was further shown that the milling time has significant effects on the microstructural characteristics of these alloys. Increased milling time seems to limit the grain growth of the NiMo matrix by producing well-dispersed Mo2C particles during sintering. The amount of grain boundaries greatly increases the Hall–Petch strengthening, resulting in significantly higher strength in the case of 48-h-milled NiMo-SiC DPS alloys compared with the 8-h-milled alloys. However, it was also shown that the total elongation is considerably reduced in the 48-h-milled NiMo-SiC DPS alloy due to high porosity. The porosity is a result of cold welding of the powder mixture during the extended milling process. PMID:28772747

The Effect of Milling Time on the Microstructural Characteristics and Strengthening Mechanisms of NiMo-SiC Alloys Prepared via Powder Metallurgy

Directory of Open Access Journals (Sweden)

Chao Yang

2017-04-01

Full Text Available A new generation of alloys, which rely on a combination of various strengthening mechanisms, has been developed for application in molten salt nuclear reactors. In the current study, a battery of dispersion and precipitation-strengthened (DPS NiMo-based alloys containing varying amounts of SiC (0.5–2.5 wt % were prepared from Ni-Mo-SiC powder mixture via a mechanical alloying (MA route followed by spark plasma sintering (SPS and rapid cooling. Neutron Powder Diffraction (NPD, Electron Back Scattering Diffraction (EBSD, and Transmission Electron Microscopy (TEM were employed in the characterization of the microstructural properties of these in-house prepared NiMo-SiC DPS alloys. The study showed that uniformly-dispersed SiC particles provide dispersion strengthening, the precipitation of nano-scale Ni3Si particles provides precipitation strengthening, and the solid-solution of Mo in the Ni matrix provides solid-solution strengthening. It was further shown that the milling time has significant effects on the microstructural characteristics of these alloys. Increased milling time seems to limit the grain growth of the NiMo matrix by producing well-dispersed Mo2C particles during sintering. The amount of grain boundaries greatly increases the Hall–Petch strengthening, resulting in significantly higher strength in the case of 48-h-milled NiMo-SiC DPS alloys compared with the 8-h-milled alloys. However, it was also shown that the total elongation is considerably reduced in the 48-h-milled NiMo-SiC DPS alloy due to high porosity. The porosity is a result of cold welding of the powder mixture during the extended milling process.

The Effect of Milling Time on the Microstructural Characteristics and Strengthening Mechanisms of NiMo-SiC Alloys Prepared via Powder Metallurgy.

Science.gov (United States)

Yang, Chao; Muránsky, Ondrej; Zhu, Hanliang; Thorogood, Gordon J; Avdeev, Maxim; Huang, Hefei; Zhou, Xingtai

2017-04-06

A new generation of alloys, which rely on a combination of various strengthening mechanisms, has been developed for application in molten salt nuclear reactors. In the current study, a battery of dispersion and precipitation-strengthened (DPS) NiMo-based alloys containing varying amounts of SiC (0.5-2.5 wt %) were prepared from Ni-Mo-SiC powder mixture via a mechanical alloying (MA) route followed by spark plasma sintering (SPS) and rapid cooling. Neutron Powder Diffraction (NPD), Electron Back Scattering Diffraction (EBSD), and Transmission Electron Microscopy (TEM) were employed in the characterization of the microstructural properties of these in-house prepared NiMo-SiC DPS alloys. The study showed that uniformly-dispersed SiC particles provide dispersion strengthening, the precipitation of nano-scale Ni₃Si particles provides precipitation strengthening, and the solid-solution of Mo in the Ni matrix provides solid-solution strengthening. It was further shown that the milling time has significant effects on the microstructural characteristics of these alloys. Increased milling time seems to limit the grain growth of the NiMo matrix by producing well-dispersed Mo₂C particles during sintering. The amount of grain boundaries greatly increases the Hall-Petch strengthening, resulting in significantly higher strength in the case of 48-h-milled NiMo-SiC DPS alloys compared with the 8-h-milled alloys. However, it was also shown that the total elongation is considerably reduced in the 48-h-milled NiMo-SiC DPS alloy due to high porosity. The porosity is a result of cold welding of the powder mixture during the extended milling process.

Magnetic properties of nanocrystalline Fe–10%Ni alloy obtained by planetary ball mills

International Nuclear Information System (INIS)

Hamzaoui, Rabah; Elkedim, Omar

2013-01-01

Highlights: •Solid solution formation accompanied by a grain refinement for nanocrystalline Fe-Ni. •The shock mode process (SMP) prevails when Ω > >ω. •The friction mode process (FMP) is stronger when Ω < <ω. •The FMP leads to the formation of alloys exhibiting a soft magnetic behavior. -- Abstract: Planetary ball mill PM 400 from Retsch (with different milling times for Ω = 400 rpm, ω = 800 rpm) and P4 vario ball mill from Fritsch (with different milling conditions (Ω/ω), Ω and ω being the disc and the vial rotation speeds, respectively) are used for obtaining nanocrystalline Fe–10wt% Ni. The structure and magnetic properties are studied by using X-ray diffraction, SEM and hysteresis measurements, respectively. The bcc-Fe(Ni) phase formation is identified by X-ray diffraction. The higher the shock power and the higher milling time are, the larger the bcc lattice parameter and the lower the grain size. The highest value of the coercivity is 1600 A/m for Fe–10 wt.%Ni (with shock mode (424 rpm/100 rpm) after 36 h of milling), while the lowest value is 189 A/m for (400 rpm/800 rpm) after 72 h of milling. The milling performed in the friction mode has been found to lead the formation of alloys exhibiting a soft magnetic behavior for nanocrystalline Fe–10%Ni

Preparation of Nd–Fe–B sintered magnets from HDDR-processed powder

Energy Technology Data Exchange (ETDEWEB)

Takagi, Kenta, E-mail: k-takagi@aist.go.jp [Green Innovative Magnetic Materials Research Center, National Institute of Advanced Industrial Science and Technology (AIST), Nagoya 463-8560 (Japan); Akada, Misaho [Magnetic Materials R& D Center, Research Associations of Magnetic Materials for High-Efficiency Motors (MagHEM), Nagoya 463-8560 (Japan); Soda, Rikio; Ozaki, Kimihiro [Green Innovative Magnetic Materials Research Center, National Institute of Advanced Industrial Science and Technology (AIST), Nagoya 463-8560 (Japan)

2015-11-01

The electric-current sintering technique was used to fully densify hydrogenation–disproportionation–desorption–recombination (HDDR)-processed Nd–Fe–B powder at temperatures below the grain growth temperature in order to produce high-coercive bulk magnets. However, the sintered magnets exhibited anomalous coercivity reduction that depended on sintered density. Reheating examination of the sintered magnets revealed that the reduced coercivity was increased in proportion to the heating temperature, resulting in complete recovery of coercivity. As a result, the combination of electric-current sintering and post-annealing produced sintered magnets with a coercivity of 15 kOe. Scanning and transmission electron microscopy revealed no evidence that associated the anomalous coercivity reduction and recovery with grain boundary morphology. On the other hand, various HDDR powders with different particle sizes were sintered, and finer powders yielded lower coercivity after sintering, implying that the anomalous coercivity reduction was associated with particle surface oxides of the raw powder. - Highlights: • We conduct a sintering of HDDR-processed Nd–Fe–B powder without coercivity reduction. • Rapid current sintering allows densification of this powder without grain growth. • However, the sintered magnets show an anomalous coercivity reduction phenomenon. • It is found that post-annealing completely recovers the reduced coercivity. • The anomalous coercivity reduction would be due to surface oxide of the raw powder.

Microstructural Evolution, Thermodynamics, and Kinetics of Mo-Tm2O3 Powder Mixtures during Ball Milling

Directory of Open Access Journals (Sweden)

Yong Luo

2016-10-01

Full Text Available The microstructural evolution, thermodynamics, and kinetics of Mo (21 wt % Tm2O3 powder mixtures during ball milling were investigated using X-ray diffraction and transmission electron microscopy. Ball milling induced Tm2O3 to be decomposed and then dissolved into Mo crystal. After 96 h of ball milling, Tm2O3 was dissolved completely and the supersaturated nanocrystalline solid solution of Mo (Tm, O was obtained. The Mo lattice parameter increased with increasing ball-milling time, opposite for the Mo grain size. The size and lattice parameter of Mo grains was about 8 nm and 0.31564 nm after 96 h of ball milling, respectively. Ball milling induced the elements of Mo, Tm, and O to be distributed uniformly in the ball-milled particles. Based on the semi-experimental theory of Miedema, a thermodynamic model was developed to calculate the driving force of phase evolution. There was no chemical driving force to form a crystal solid solution of Tm atoms in Mo crystal or an amorphous phase because the Gibbs free energy for both processes was higher than zero. For Mo (21 wt % Tm2O3, it was mechanical work, not the negative heat of mixing, which provided the driving force to form a supersaturated nanocrystalline Mo (Tm, O solid solution.

Removal of fluoride from drinking water using modified ultrafine tea powder processed using a ball-mill

Energy Technology Data Exchange (ETDEWEB)

Cai, Huimei; Xu, Lingyun; Chen, Guijie; Peng, Chuanyi [School of Tea & Food Science and Technology, Anhui Agricultural University/State Key Laboratory of Tea Plant Biology and Utilization, Anhui Agricultural University, Hefei 230036, Anhui (China); Ke, Fei [School of Tea & Food Science and Technology, Anhui Agricultural University/State Key Laboratory of Tea Plant Biology and Utilization, Anhui Agricultural University, Hefei 230036, Anhui (China); School of Science, Anhui Agricultural University, Hefei 230036 (China); Liu, Zhengquan; Li, Daxiang; Zhang, Zhengzhu [School of Tea & Food Science and Technology, Anhui Agricultural University/State Key Laboratory of Tea Plant Biology and Utilization, Anhui Agricultural University, Hefei 230036, Anhui (China); Wan, Xiaochun, E-mail: xcwan@ahau.edu.cn [School of Tea & Food Science and Technology, Anhui Agricultural University/State Key Laboratory of Tea Plant Biology and Utilization, Anhui Agricultural University, Hefei 230036, Anhui (China)

2016-07-01

Highlights: • Ultrafine tea powder (UTP) was prepared by ball-milling. • A novel and high efficient biosorbent from ultrafine tea powder (UTP) for the removal of fluoride from drinking water was prepared. • Loaded ultrafine tea powder adsorbed more fluoride adsorption than loaded tea waste. • UTP-Zr performed well over a considerably wide pH range, from 3.0 to 10.0. • UTP-Zr retains Zr metal ion during defluoridation, limiting secondary pollution. - Abstract: A low-cost and highly efficient biosorbent was prepared by loading zirconium(IV) onto ball-milled, ultrafine tea powder (UTP-Zr) for removal of fluoride from drinking water. To evaluate the fluoride adsorption capacity of UTP-Zr over a wide range of conditions, the biosorbent dosage, contact time, initial pH, initial fluoride concentration and presence of other ions were varied. UTP-Zr performed well over the considerably wide pH range of 3–10. The residual concentration of Zr in the treated water was below the limit of detection (0.01 mg/L). Fluoride adsorption by the UTP-Zr biosorbent followed the Langmuir model, with a maximum adsorption capacity of 12.43 mgF/g at room temperature. The fluoride adsorption kinetics fit the pseudo-second-order kinetic model. The synthesized biosorbent was characterized by BET, SEM, EDS, XRD and XPS to reveal how UTP-Zr interacts with fluoride. Results from this study demonstrated that UTP-based biosorbents will be useful and safe for the removal of fluoride from drinking water.

Removal of fluoride from drinking water using modified ultrafine tea powder processed using a ball-mill

International Nuclear Information System (INIS)

Cai, Huimei; Xu, Lingyun; Chen, Guijie; Peng, Chuanyi; Ke, Fei; Liu, Zhengquan; Li, Daxiang; Zhang, Zhengzhu; Wan, Xiaochun

2016-01-01

Highlights: • Ultrafine tea powder (UTP) was prepared by ball-milling. • A novel and high efficient biosorbent from ultrafine tea powder (UTP) for the removal of fluoride from drinking water was prepared. • Loaded ultrafine tea powder adsorbed more fluoride adsorption than loaded tea waste. • UTP-Zr performed well over a considerably wide pH range, from 3.0 to 10.0. • UTP-Zr retains Zr metal ion during defluoridation, limiting secondary pollution. - Abstract: A low-cost and highly efficient biosorbent was prepared by loading zirconium(IV) onto ball-milled, ultrafine tea powder (UTP-Zr) for removal of fluoride from drinking water. To evaluate the fluoride adsorption capacity of UTP-Zr over a wide range of conditions, the biosorbent dosage, contact time, initial pH, initial fluoride concentration and presence of other ions were varied. UTP-Zr performed well over the considerably wide pH range of 3–10. The residual concentration of Zr in the treated water was below the limit of detection (0.01 mg/L). Fluoride adsorption by the UTP-Zr biosorbent followed the Langmuir model, with a maximum adsorption capacity of 12.43 mgF/g at room temperature. The fluoride adsorption kinetics fit the pseudo-second-order kinetic model. The synthesized biosorbent was characterized by BET, SEM, EDS, XRD and XPS to reveal how UTP-Zr interacts with fluoride. Results from this study demonstrated that UTP-based biosorbents will be useful and safe for the removal of fluoride from drinking water.

The processing and characterization of animal-derived bone to yield materials with biomedical applications. Part II: milled bone powders, reprecipitated hydroxyapatite and the potential uses of these materials.

Science.gov (United States)

Johnson, G S; Mucalo, M R; Lorier, M A; Gieland, U; Mucha, H

2000-11-01

Further studies on the processing and use of animal-bone-derived calcium phosphate materials in biomedical applications are presented. Bone powders sourced either from the direct crushing and milling of bovine, ovine and cervine bone or after being subjected to defatting and acid digestion/NaOH reprecipitation and sodium hypochlorite hydrogen peroxide treatment of animal bones were characterized using Fourier transform infra-red (FTIR) spectroscopy, 13C solid state magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy, atomic absorption (AA) and inductively coupled plasma (ICP) spectrometric techniques. Bone powders were trialled for their potential use as a substrate for phosphine coupling and enzyme immobilization as well as a feedstock powder for plasma spraying on titanium metal substrates. Results indicated that enzyme immobilization by phosphine coupling could be successfully achieved on milled cervine bone with the immobilized enzyme retaining some activity. It was found that the presence of impurities normally carried down with the processing of the bone materials (viz., fat and collagen) played an important role in influencing the adsorbency and reactivity of the powders. Plasma spraying studies using reprecipitated bovine-derived powders produced highly adherent coatings on titanium metal, the composition of which was mostly hydroxyapatite (Ca10(PO4)6(OH)2) with low levels of alpha-tricalcium phosphate (alpha-Ca3(PO4)2) and tetracalcium phosphate (Ca4P2O9) also detected. In general, animal derived calcium phosphate materials constitute a potentially cheaper source of calcium phosphate materials for biomedical applications and make use of a largely under-utilized resource from abattoir wastes. Copyright 2000 Kluwer Academic Publishers

Obtention of the TiFe compound by high-energy milling of Ti+Fe and TiH{sub 2}+Fe powder mixtures; Obtencao do composto TiFe a partir da moagem de alta energia de misturas Ti+Fe e TiH{sub 2}+Fe

Energy Technology Data Exchange (ETDEWEB)

Falcao, R.B.; Dammann, E.D.C.C.; Rocha, C.J.; Leal Neto, R.M., E-mail: railson.falcao@usp.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Ciencias e Tecnologia de Materiais. Lab. de Intermetalicos

2010-07-01

In this work TiFe compound was obtained by two process routes involving high-energy ball milling: mechanical alloying from Ti and Fe powders (route 1) and mechanical milling from TiH{sub 2} and Fe powders, both followed by an annealing heat treatment. Shaker and planetary ball mills were utilized for times varying from 1-25 hours. Milled and annealed powders were characterized by SEM and X-ray diffraction analyses. TiFe compound was formed in both routes. A strong powder adherence in the milling vial and balls occurred with route 1 in both mills. Powder adherence was significantly reduced by using TiH{sub 2} (route 2) mainly in the planetary mill, in spite of TiFe formation has only occurred after the annealing treatment. (author)

Development of NdFeB magnet through hydrogen decrepitation

International Nuclear Information System (INIS)

Akhtar, S.; Farooque, M.; Haider, A.; Ahmad, Z.

2009-01-01

Neodymium based magnets are the powerful permanent magnet of today. This paper will discuss iron based rare earth magnets. NdFeB sintered magnet material has been developed. The magnets are produced by powder metallurgy route involving hydrogen decrepitation technique for making fine powder. After melting and casting, the NdFeB alloy is subject to hydrogen atmosphere. Hydrogen slowly absorbs into the solid alloy and makes it brittle, which upon milling becomes fine powder. Hydrogen is then removed by placing the powder at temperature around 800 deg. C under vacuum. Then the powders are pressed under isostatic conditions and sintered at temperature range of 1020-1050 deg. C. Post sintering is done at 800 deg. C and 580 deg. C followed by quenching. Energy product in the range of 8 MGOe is achieved. (author)

Polycrystalline Nd{sub 2}Fe{sub 14}B/α-Fe nanocomposite flakes with a sub-micro/nanometre thickness prepared by surfactant-assisted high-energy ball milling

Energy Technology Data Exchange (ETDEWEB)

Tang, Xin, E-mail: tangshincn@gmail.com [Key Laboratory of Magnetic Materials and Devices, Ningbo Institute of Material Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Chen, Xi [Mechanical and Electrical Engineering College, Xinxiang University, No. 192, Jinsui Road, Xinxiang, Henan 453003 (China); Chen, Renjie; Yan, Aru [Key Laboratory of Magnetic Materials and Devices, Ningbo Institute of Material Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China)

2015-09-25

Highlights: • Nd{sub 2}Fe{sub 14}B/α-Fe flakes are formed by peeling along preferential planes. • (0 0 l) planes are found to be preferential cleavage planes. • Magnetic properties degrade with increasing ball milling time. • Anisotropic nanocomposite magnets are fabricated. - Abstract: A surfactant-assisted high-energy ball milling technique was employed to synthesize Nd{sub 2}Fe{sub 14}B/α-Fe nanoparticles and nanoflakes from melt-spun nanocrystalline powders. The microstructure evolution in ball milling process was investigated. In the beginning stage (0–4 h) of ball milling, raw powders were crushed into micrometre-sized particles. While flakes were mainly formed by reducing thickness of particles via peeling layer by layer along preferential planes in the late stage (8–16 h). The selected area electron diffraction and high-resolution transmission electron microscopy images show that preferential cleavage planes are basal planes. With ball milling proceeding, more and more defects were induced by ball milling. As a result, the coercivity and remanence decreased to 1.6 kOe and 3.2 kGs, respectively. After 16 h ball milling, the exchange decoupling occurred due to severe amorphorization. A weakly-textured nanocomposite magnet was fabricated after 12 h ball milling and the anisotropy in magnetic properties can be further improved by employing settling down process to select particle size and aligning particles in external field.

Determination of milling parameters to obtain mechanosynthesized ZnFe2O4

International Nuclear Information System (INIS)

Jean, Malick; Nachbaur, Virginie

2008-01-01

In this work, the mechanosynthesis of zinc ferrite in WC vials is studied. Millings are performed under air, with a planetary ball-milling, starting from elemental oxides α-Fe 2 O 3 and ZnO. As-milled powders are structurally and magnetically characterized by X-ray diffraction and Moessbauer spectroscopy. Milling parameters as rotational speeds of main disc and vials are particularly discussed in terms of influence on the obtaining of a pure zinc ferrite phase. These parameters have a strong influence on injected power, on radial and tangential components of the impact force. Friction phenomenon, associated with injected power, have been found to be the governing parameters of the end product

The Effect of Powder Ball Milling on the Microstructure and Mechanical Properties of Sintered Fe-Cr-Mo-Mn-(Cu) Steel

Science.gov (United States)

Kulecki, P.; Lichańska, E.

2017-12-01

The effect of ball milling powder mixtures of Höganäs pre-alloyed iron Astaloy CrM, low-carbon ferromanganese Elkem, elemental electrolytic Cu and C-UF graphite on the sintered structure and mechanical properties was evaluated. The mixing was conducted using Turbula mixer for 30 minutes and CDI-EM60 frequency inverter for 1 and 2 hours. Milling was performed on 150 g mixtures with (in weight %) CrM + 1% Mn, CrM + 2% Mn, CrM + 1% Mn + 1% Cu and CrM + 2% Mn + 1% Cu, all with 0.6%C. The green compacts were single pressed at 660 MPa according to PN-EN ISO 2740. Sintering was carried out in a laboratory horizontal furnace Carbolite STF 15/450 at 1250°C for 60 minutes in 5%H2 - 95%N2 atmosphere with a heating rate of 75°C/min, followed by sintering hardening at 60°C/min cooling rate. All the steels were characterized by martensitic structures. Mechanical testing revealed that steels based on milled powders have slightly higher mechanical properties compared to those only mixed and sintered. The best combination of mechanical properties, for ball milled CrM + 1% Mn + 1% Cu was UTS 1046 MPa, TRS 1336 MPa and A 1.94%.

Effects of Fe fine powders doping on hot deformed NdFeB magnets

International Nuclear Information System (INIS)

Lin, Min; Wang, Huijie; Zheng, Jingwu; Yan, Aru

2015-01-01

The composite NdFeB magnets with blending melt-spun flakes and Fe fine powders were prepared by the hot-pressed and hot-deformed route. Characterizations of the hot-deformed NdFeB magnets affected by the doped Fe powders were tested. The doped Fe powders decrease the hot-deformed pressure when the strain is between 15 and 50%. XRD patterns show that the doped Fe powders have little influence on the c-axis alignment of hot-deformed NdFeB magnets in the press direction. The B r and the (BH) max get improved when the doped Fe powders are less than 3 wt%. The doped Fe of hot-deformed NdFeB magnets exists in the elongated state and the spherical state surrounded by the Nd-rich phase. With the Fe fraction increasing, the potential of magnet moves to the positive direction and the diameter of the Nyquist arc becomes larger, which indicate that the corrosion resistance improved effectively. The bending strength was enhanced by the elongated α-Fe phase embedded in the matrix 2:14:1 phase. - Highlights: • The doped Fe powders have little influence on the c-axis alignment of magnets. • The elongated Fe powders are more than the spherical Fe powders in the magnets. • The corrosion resistance is improved effectively with the increasing Fe fraction. • The bending strength is enhanced by the elongated α-Fe phase embedded in the matrix

Effects of Fe fine powders doping on hot deformed NdFeB magnets

Energy Technology Data Exchange (ETDEWEB)

Lin, Min, E-mail: linm@nimte.ac.cn [Ningbo Institute of Material Technology & Engineering Chinese Academy of Science, Ningbo 315201 (China); Wang, Huijie [Ningbo Jinji Strong Magnetic Material Company, Ningbo 315041 (China); Zheng, Jingwu [Zhejiang University of Technology, Hangzhou 310014 (China); Yan, Aru [Ningbo Institute of Material Technology & Engineering Chinese Academy of Science, Ningbo 315201 (China)

2015-04-01

The composite NdFeB magnets with blending melt-spun flakes and Fe fine powders were prepared by the hot-pressed and hot-deformed route. Characterizations of the hot-deformed NdFeB magnets affected by the doped Fe powders were tested. The doped Fe powders decrease the hot-deformed pressure when the strain is between 15 and 50%. XRD patterns show that the doped Fe powders have little influence on the c-axis alignment of hot-deformed NdFeB magnets in the press direction. The B{sub r} and the (BH){sub max} get improved when the doped Fe powders are less than 3 wt%. The doped Fe of hot-deformed NdFeB magnets exists in the elongated state and the spherical state surrounded by the Nd-rich phase. With the Fe fraction increasing, the potential of magnet moves to the positive direction and the diameter of the Nyquist arc becomes larger, which indicate that the corrosion resistance improved effectively. The bending strength was enhanced by the elongated α-Fe phase embedded in the matrix 2:14:1 phase. - Highlights: • The doped Fe powders have little influence on the c-axis alignment of magnets. • The elongated Fe powders are more than the spherical Fe powders in the magnets. • The corrosion resistance is improved effectively with the increasing Fe fraction. • The bending strength is enhanced by the elongated α-Fe phase embedded in the matrix.

Influence of spark plasma sintering conditions on the sintering and functional properties of an ultra-fine grained 316L stainless steel obtained from ball-milled powder

Energy Technology Data Exchange (ETDEWEB)

Keller, C., E-mail: clement.keller@insa-rouen.fr [Groupe de Physique des Matériaux, CNRS-UMR 6634, Université de Rouen, INSA de Rouen, Avenue de l' Université, 76800 Saint-Etienne du Rouvray (France); Tabalaiev, K.; Marnier, G. [Groupe de Physique des Matériaux, CNRS-UMR 6634, Université de Rouen, INSA de Rouen, Avenue de l' Université, 76800 Saint-Etienne du Rouvray (France); Noudem, J. [Laboratoire de Cristallographie des Matériaux, CNRS-UMR 6508, Université de Caen, ENSICAEN, 7 bd du Maréchal Juin, 14050 Caen (France); Sauvage, X. [Groupe de Physique des Matériaux, CNRS-UMR 6634, Université de Rouen, INSA de Rouen, Avenue de l' Université, 76800 Saint-Etienne du Rouvray (France); Hug, E. [Laboratoire de Cristallographie des Matériaux, CNRS-UMR 6508, Université de Caen, ENSICAEN, 7 bd du Maréchal Juin, 14050 Caen (France)

2016-05-17

In this work, 316L samples with submicrometric grain size were sintered by spark plasma sintering. To this aim, 316L powder was first ball-milled with different conditions to obtain nanostructured powder. The process control agent quantity and milling time were varied to check their influence on the crystallite size of milled powder. Samples were then sintered by spark plasma sintering using different sets of sintering parameters (temperature, dwell time and pressure). For each sample, grain size and density were systematically measured in order to investigate the influence of the sintering process on these two key microstructure parameters. Results show that suitable ball-milling and subsequent sintering can be employed to obtain austenitic stainless steel samples with grain sizes in the nanometer range with porosity lower than 3%. However, ball-milling and subsequent sintering enhance chromium carbides formation at the sample surface in addition to intragranular and intergranular oxides in the sample as revealed by X-ray diffraction and transmission electron microscopy. It has been shown that using Boron nitride together with graphite foils to protect the mold from powder welding prevent such carbide formation. For mechanical properties, results show that the grain size refinement strongly increases the hardness of the samples without deviation from Hall-Petch relationship despite the oxides formation. For corrosion resistance, grain sizes lower than a few micrometers involve a strong decrease in the pitting potential and a strong increase in passivation current. As a consequence, spark plasma sintering can be considered as a promising tool for ultra-fine grained austenitic stainless steel.

The crystallization of amorphous Fe2MnGe powder prepared by ball milling

International Nuclear Information System (INIS)

Zhang, L.; Brueck, E.; Tegus, O.; Buschow, K.H.J.; Boer, F.R. de

2003-01-01

We synthesized for the first time the intermetallic compound Fe 2 MnGe. To avoid preferential evaporation of volatile components we exploited mechanical alloying. Amorphous Fe 2 MnGe alloy powder was prepared by planetary ball milling elemental starting materials. The amorphous-to-crystalline transition was studied by means of differential scanning calorimetry (DSC) and X-ray diffraction (XRD). A cubic D0 3 phase is formed at low temperature and transforms to a high-temperature hexagonal D0 19 phase. The apparent activation energy was determined by means of the Kissinger method

Structural evolution of Ni-20Cr alloy during ball milling of elemental powders

International Nuclear Information System (INIS)

Lopez B, I.; Trapaga M, L. G.; Martinez F, E.; Zoz, H.

2011-01-01

The ball milling (B M) of blended Ni and Cr elemental powders was carried out in a Simoloyer performing on high-energy scale mode at maximum production to obtain a nano structured Ni-20Cr alloy. The phase transformations and structural changes occurring during mechanical alloying were investigated by X-ray diffraction (XRD) and optical microscopy (Om). A gradual solid solubility of Cr and the subsequent formation of crystalline metastable solid solutions described in terms of the Avrami-Ero fe ev kinetics model were calculated. The XRD analysis of the structure indicates that cumulative lattice strain contributes to the driving force for solid solution between Ni and Cr during B M. Microstructure evolution has shown, additionally to the lamellar length refinement commonly observed, the folding of lamellae in the final processing stage. Om observations revealed that the lamellar spacing of Ni rich zones reaches a steady value near 500 nm and almost disappears after 30 h of milling. (Author)

Structural evolution of Ni-20Cr alloy during ball milling of elemental powders

Energy Technology Data Exchange (ETDEWEB)

Lopez B, I.; Trapaga M, L. G. [IPN, Centro de Investigacion y de Estudios Avanzados, Unidad Queretaro, Libramiento Norponiente No. 2000, Juriquilla, 76230 Queretaro (Mexico); Martinez F, E. [Centro de Investigacion e Innovacion Tecnologica, Cerrada de Cecati s/n, Col. Santa Catarina Azcapotzalco, 02250 Mexico D. F. (Mexico); Zoz, H., E-mail: israelbaez@gmail.co [Zoz GmbH, D-57482, Wenden (Germany)

2011-07-01

The ball milling (B M) of blended Ni and Cr elemental powders was carried out in a Simoloyer performing on high-energy scale mode at maximum production to obtain a nano structured Ni-20Cr alloy. The phase transformations and structural changes occurring during mechanical alloying were investigated by X-ray diffraction (XRD) and optical microscopy (Om). A gradual solid solubility of Cr and the subsequent formation of crystalline metastable solid solutions described in terms of the Avrami-Ero fe ev kinetics model were calculated. The XRD analysis of the structure indicates that cumulative lattice strain contributes to the driving force for solid solution between Ni and Cr during B M. Microstructure evolution has shown, additionally to the lamellar length refinement commonly observed, the folding of lamellae in the final processing stage. Om observations revealed that the lamellar spacing of Ni rich zones reaches a steady value near 500 nm and almost disappears after 30 h of milling. (Author)

Enhancement of exchange coupling interaction of NdFeB/MnBi hybrid magnets

Science.gov (United States)

Nguyen, Truong Xuan; Nguyen, Khanh Van; Nguyen, Vuong Van

2018-03-01

MnBi ribbons were fabricated by melt - spinning with subsequent annealing. The MnBi ribbons were ground and mixed with NdFeB commercial Magnequench powders (MQA). The hybrid powder mixtures were subjected thrice to the annealing and ball-milling route. The hybrid magnets (100 - x)NdFeB/xMnBi, x=0, 30, 40, 50 and 100 wt% were in-mold aligned in an 18 kOe magnetic field and warm compacted at 290 °C by 2000 psi uniaxial pressure for 10 min. An enhancement of the exchange coupling of NdFeB/MnBi hybrid magnets was obtained by optimizing the magnets' microstructures via annealing and ball-milling processes. The magnetic properties of prepared NdFeB/MnBi hybrid magnets were studied and discussed in details.

High-Yield Preparation and Electrochemical Properties of Few-Layer MoS2 Nanosheets by Exfoliating Natural Molybdenite Powders Directly via a Coupled Ultrasonication-Milling Process

Science.gov (United States)

Dong, Huina; Chen, Deliang; Wang, Kai; Zhang, Rui

2016-09-01

Cost-effective and scalable preparation of two-dimensional (2D) molybdenum disulfide (MoS2) has been the bottleneck that limits their applications. This paper reports a novel coupled ultrasonication-milling (CUM) process to exfoliate natural molybdenite powders to achieve few-layer MoS2 (FL-MoS2) nanosheets in the solvent of N-methyl-2-pyrrolidone (NMP) with polyvinylpyrrolidone (PVP) molecules. The synergistic effect of ultrasonication and sand milling highly enhanced the exfoliation efficiency, and the precursor of natural molybdenite powders minimizes the synthetic cost of FL-MoS2 nanosheets. The exfoliation of natural molybdenite powders was conducted in a home-made CUM system, mainly consisting of an ultrasonic cell disruptor and a ceramic sand mill. The samples were characterized by X-ray diffraction, UV-vis spectra, Raman spectra, FT-IR, SEM, TEM, AFM, and N2 adsorption-desorption. The factors that influence the exfoliation in the CUM process, including the initial concentration of natural molybdenite powders ( C in, 15-55 g L-1), ultrasonic power ( P u, 200-350 W), rotation speed of sand mill ( ω s, 1500-2250 r.p.m), exfoliation time ( t ex, 0.5-6 h), and the molar ratio of PVP unit to MoS2 ( R pm, 0-1), were systematically investigated. Under the optimal CUM conditions (i.e., C in = 45 g L-1, P u = 280 W, ω s = 2250 r.p.m and R pm = 0.5), the yield at t ex = 6 h reaches 21.6 %, and the corresponding exfoliation rate is as high as 1.42 g L-1 h-1. The exfoliation efficiency of the CUM mode is much higher than that of either the ultrasonication (U) mode or the milling (M) mode. The synergistic mechanism and influencing rules of the CUM process in exfoliating natural molybdenite powders were elaborated. The as-obtained FL-MoS2 nanosheets have a high specific surface area of 924 m2 g-1 and show highly enhanced electrocatalytic performance in hydrogen evolution reaction and good electrochemical sensing property in detecting ascorbic acid. The CUM process

Milling Behavior of Matrix Graphite Powders with Different Binder Materials in HTGR Fuel Element Fabrication: I. Variation in Particle Size Distribution

International Nuclear Information System (INIS)

Lee, Young Woo; Cho, Moon Sung

2011-01-01

The fuel element for HTGR is manufactured by mixing coated fuel particles with matrix graphite powder and forming into either pebble type or cylindrical type compacts depending on their use in different HTGR cores. The coated fuel particle, the so-called TRISO particle, consists of 500-μm spherical UO 2 particles coated with the low density buffer Pyrolytic Carbon (PyC) layer, the inner and outer high density PyC layer and SiC layer sandwiched between the two inner and outer PyC layers. The coated TRISO particles are mixed with a matrix graphite powder properly prepared and pressed into a spherical shape or a cylindrical compact finally heat-treated at about 1900 .deg. C. These fuel elements can have different sizes and forms of compact. The basic steps for manufacturing a fuel element include preparation of graphite matrix powder, overcoating the fuel particles, mixing the fuel particles with a matrix powder, carbonizing green compact, and the final high-temperature heat treatment of the carbonized fuel compact. In order to develop a fuel compact fabrication technology, it is important to develop a technology to prepare the matrix graphite powder (MGP) with proper characteristics, which has a strong influence on further steps and the material properties of fuel element. In this work, the milling behavior of matrix graphite powder mixture with different binder materials and their contents was investigated by analyzing the change in particle size distribution with different milling time

Influence of Process Control Agent on Characterization and Structure of Micron Chitosan Powders Prepared by Ball Milling Method

Directory of Open Access Journals (Sweden)

ZHANG Chuan-jie

2016-12-01

Full Text Available With ethyl alcohol or distilled water as process control agent (PCA, micron chitosan powder was prepared by ball milling method. The yield rate, particle size distribution, micro morphology, viscosity average molecular mass, chemical and crystal structures, and thermal properties of these different micron chitosan powders were measured. The results indicate that the yield rate of micron chitosan powders prepared with ethyl alcohol as PCA increases significantly, and improves to 94.7% from 25% while the amount of ethyl alcohol is 0.75mL/g. The particle size distribution of micron chitosan powder prepared with ethyl alcohol as PCA is concentrated, while the D50 and D90 in size are 824nm and 1629nm respectively. Chitosan do not react with ethyl alcohol used as PCA, but the viscosity average molecular mass of prepared micron chitosan powder decreases by 23%, the crystal structures are destroyed slightly, and its thermal stability is slightly weakened.

Low-energy mechanically milled τ-phase MnAl alloys with high coercivity and magnetization

International Nuclear Information System (INIS)

Lu, Wei; Niu, Junchao; Wang, Taolei; Xia, Kada; Xiang, Zhen; Song, Yiming; Zhang, Hong; Yoshimura, Satoru; Saito, Hitoshi

2016-01-01

The high cost of rare earth elements makes the use of high-performance permanent magnets commercially very expensive. MnAl magnetic material is one of the most promising Rare-Earth-free permanent magnets due to its obvious characteristics. However, the coercivity of MnAl alloys produced by melt spinning followed by appropriate treatment is relatively low. In this investigation, a high coercivity up to 5.3 kOe and saturation magnetization of ∼62 emu/g (with an applied magnetic field of 19.5 kOe) were obtained in the mechanically milled τ-phase Mn_5_7Al_4_3 alloy. As milling time goes on, the coercivity firstly increases and then decreases, leading to the formation of knee-point coercivity, while the saturation magnetization decreases simultaneously. The structural imperfections such as disordering and defects play the most important role in the changes of magnetic properties of τ-phase MnAl alloys processed by low-energy mechanical milling. The present results will be helpful for the development of processing protocols for the optimization of τ-phase MnAl alloys as high performance Rare-Earth-free permanent magnets. - Highlights: • Successful fabrication of pure τ-phase Mn_5_7Al_4_3 alloy by melt spinning and low-energy ball milling processes. • High coercivity (~5.3 kOe) and magnetization (~62 emu/g) were obtained in τ-phase Mn_5_7Al_4_3 alloy. • Disordering and defects play the most important role in the changes of magnetic properties.

Low-energy mechanically milled τ-phase MnAl alloys with high coercivity and magnetization

Energy Technology Data Exchange (ETDEWEB)

Lu, Wei, E-mail: weilu@tongji.edu.cn [School of Materials Science and Engineering, Shanghai Key Lab. of D& A for Metal-Functional Materials, Tongji University, Shanghai 200092 (China); Research Center for Engineering Science, Akita University, Akita 010-8502 Japan (Japan); Niu, Junchao; Wang, Taolei; Xia, Kada; Xiang, Zhen; Song, Yiming [School of Materials Science and Engineering, Shanghai Key Lab. of D& A for Metal-Functional Materials, Tongji University, Shanghai 200092 (China); Zhang, Hong; Yoshimura, Satoru; Saito, Hitoshi [Research Center for Engineering Science, Akita University, Akita 010-8502 Japan (Japan)

2016-08-05

The high cost of rare earth elements makes the use of high-performance permanent magnets commercially very expensive. MnAl magnetic material is one of the most promising Rare-Earth-free permanent magnets due to its obvious characteristics. However, the coercivity of MnAl alloys produced by melt spinning followed by appropriate treatment is relatively low. In this investigation, a high coercivity up to 5.3 kOe and saturation magnetization of ∼62 emu/g (with an applied magnetic field of 19.5 kOe) were obtained in the mechanically milled τ-phase Mn{sub 57}Al{sub 43} alloy. As milling time goes on, the coercivity firstly increases and then decreases, leading to the formation of knee-point coercivity, while the saturation magnetization decreases simultaneously. The structural imperfections such as disordering and defects play the most important role in the changes of magnetic properties of τ-phase MnAl alloys processed by low-energy mechanical milling. The present results will be helpful for the development of processing protocols for the optimization of τ-phase MnAl alloys as high performance Rare-Earth-free permanent magnets. - Highlights: • Successful fabrication of pure τ-phase Mn{sub 57}Al{sub 43} alloy by melt spinning and low-energy ball milling processes. • High coercivity (~5.3 kOe) and magnetization (~62 emu/g) were obtained in τ-phase Mn{sub 57}Al{sub 43} alloy. • Disordering and defects play the most important role in the changes of magnetic properties.

Refinement of Crystalline Boron and the Superconducting Properties of MgB2 by Attrition Ball Milling

International Nuclear Information System (INIS)

Lee, J. H.; Shin, S. Y.; Park, H. W.; Jun, B. H.; Kim, C. J.

2008-01-01

We report refinement of crystalline boron by an attrition ball milling system and the superconducting properties of the MgB 2 pellets prepared from the refined boron. In this work, we have conducted the ball milling with only crystalline boron powder, in order to improve homogeneity and control the grain size of the MgB 2 that is formed from it. We observed that the crystalline responses in the ball-milled boron became broader and weaker when the ball-milling time was further increased. On the other hand, the B 2 O 3 peak became stronger in the powders, resulting in an increase in the amount of MgO within the MgB 2 volume. The main reason for this is a greater oxygen uptake. From the perspective of the superconducting properties, however, the sample prepared from boron that was ball milled for 5 hours showed an improvement of critical current density (J c ), even with increased MgO phase, under an external magnetic field at 5 and 20 K.

Improved hydrogen sorption kinetics in wet ball milled Mg hydrides

Energy Technology Data Exchange (ETDEWEB)

Meng, Li

2011-05-04

In this work, wet ball milling method is used in order to improve hydrogen sorption behaviour due to its improved microstructure of solid hydrogen materials. Compared to traditional ball milling method, wet ball milling has benefits on improvement of MgH{sub 2} microstructure and further influences on its hydrogen sorption behavior. With the help of solvent tetrahydrofuran (THF), wet ball milled MgH{sub 2} powder has much smaller particle size and its specific surface area is 7 times as large as that of dry ball milled MgH{sub 2} powder. Although after ball milling the grain size is decreased a lot compared to as-received MgH{sub 2} powder, the grain size of wet ball milled MgH{sub 2} powder is larger than that of dry ball milled MgH{sub 2} powder due to the lubricant effect of solvent THF during wet ball milling. The improved particle size and specific surface area of wet ball milled MgH{sub 2} powder is found to be determining its hydrogen sorption kinetics especially at relatively low temperatures. And it also shows good cycling sorption behavior, which decides on its industrial applicability. With three different catalysts MgH{sub 2} powder shows improved hydrogen sorption behavior as well as the cyclic sorption behavior. Among them, the Nb{sub 2}O{sub 5} catalyst is found to be the most effective one in this work. Compared to the wet ball milled MgH{sub 2} powder, the particle size and specific surface area of the MgH{sub 2} powder with catalysts are similar to the previous ones, while the grain size of the MgH{sub 2} with catalysts is much finer. In this case, two reasons for hydrogen sorption improvement are suggested: one is the reduction of the grain size. The other may be as pointed out in some literatures that formation of new oxidation could enhance the hydrogen sorption kinetics, which is also the reason why its hydrogen capacity is decreased compared to without catalysts. After further ball milling, the specific surface area of wet ball milled Mg

Study on the characteristics and sinterability of DUPIC powder by using simulated fuel

International Nuclear Information System (INIS)

Lee, Jae-Won; Lee, Jung-Won; Kim, Jong-Ho; Yim, Sung-Paal; Lee, Young-Woo; Yang, Myung-Seung

2002-01-01

The sinterability of the OREOX (oxidation and reduction of oxide fuels) powder was investigated in terms of the number of the OREOX cycles and milling time using simulated spent fuel of an equivalent burnup of 35,000 MWD/MTU. Wet milled powder was prepared and sintered to compare the morphology and sinterability with the dry milled powder. Powders having a medium particle size of less than 1μm were obtained by dry milling of OREOX powders regardless of the number of cycles. The specific surface area of the simulated DUPIC powder was governed by the number of OREOX cycles rather than by milling time. The sound pellets with a sintered density of higher than 95% TD and average grain size of larger than 8μm were obtained with the dry milled powder after 1 cycle of OREOX treatment. The powders prepared by dry milling for a short time and wet milling for a long time after 3 cycles of OREOX treatment also produced pellets with a sintered density of higher than 95% TD and average grain size of larger than 8μm. (author)

Production of NdFeB powders by HDDR from sintered magnets

International Nuclear Information System (INIS)

Janasi, S.R.; Rodrigues, D.; Landgraf, F.J.G.; Campos, M.F. de

2010-01-01

The production of NdFeB powders by the HDDR process from metallic alloys has been widely investigated. Different HD and DR conditions have been used to induce anisotropy and to improve the intrinsic coercivity of the obtained powders. The purpose of this study is to apply the HDDR process in the reprocessing of NdFeB sintered magnet scraps. There were investigated different processing conditions as temperature and time of desorption and recombination (DR). The results of X ray diffraction show the formation of the magnetic phase Nd 2 Fe 14 B in all the investigated conditions. Magnetic measurements by vibrating sample magnetometer indicate that powders with intrinsic coercivity up to 790 kA/m were obtained. (author)

Corroded microstructure of HDDR-NdFeB magnetic powders

International Nuclear Information System (INIS)

Zhu, L.Y.; Itakura, M.; Tomokiyo, Y.; Kuwano, N.; Machida, K.

2004-01-01

The microstructure of corroded HDDR-NdFeB magnetic powders in bonded magnet has been investigated by transmission electron microscopy. Following an exposure time of 300 h at 398 K in air, the HDDR-NdFeB magnetic powders are found covered with an altered layer about 300 nm thick on the surface. The layer is composed of α-Fe grains 5-10 nm in diameter and h-Nd 2 O 3 grains smaller than 5 nm. Under the altered layer, corrosion has proceeded along the Nd 2 (Fe,Co) 14 B grain boundaries to leave a wetting layer composed of a dense mixture of α-Fe and h-Nd 2 O 3 phase. The appearance of α-Fe grains in both of the altered layer wetting layer leads to the high magnetic flux loss of the corroded HDDR-NdFeB bonded magnet

Studies on in situ magnetic alignment of bonded anisotropic Nd-Fe-B alloy powders

Energy Technology Data Exchange (ETDEWEB)

Nlebedim, I.C. [Ames Laboratory, Ames, IA 50011 (United States); Ucar, Huseyin; Hatter, Christine B. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); McCallum, R.W. [Ames Laboratory, Ames, IA 50011 (United States); McCall, Scott K. [Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States); Kramer, M.J. [Ames Laboratory, Ames, IA 50011 (United States); Paranthaman, M. Parans [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States)

2017-01-15

Considerations for achieving high degree of alignment in polymer bonded permanent magnets are presented via the results of a study on in situ magnetic alignment of anisotropic Nd-Fe-B magnet powders. Contributions from effect of the alignment temperature, alignment magnetic field and the properties of the polymer on the hard magnetic properties of the bonded magnet were considered. The thermo-rheological properties of the polymer and the response of the magnet powders to the applied magnetic field indicate that hard magnetic properties were optimized at an alignment temperature just above the melting temperature of the EVA co-polymer. This agrees with an observed correlation between the change in magnetization due to improved magnetic alignment of the anisotropic powders and the change in viscosity of the binder. Manufacturing cost can be minimized by identifying optimum alignment temperatures and magnetic field strengths. - Highlights: • Optimum alignment of anisotropic magnet powders can enable high performance bonded magnets. • The viscoelastic state of polymer binders determines the dominating coercivity mechanism. • The minimum deviation in coercivity and remanence, with magnetic field, can occur at different temperatures. • Melting characteristics of polymer binders and the change in magnetization during alignment can be correlated.

Studies on in situ magnetic alignment of bonded anisotropic Nd-Fe-B alloy powders

International Nuclear Information System (INIS)

Nlebedim, I.C.; Ucar, Huseyin; Hatter, Christine B.; McCallum, R.W.; McCall, Scott K.; Kramer, M.J.; Paranthaman, M. Parans

2017-01-01

Considerations for achieving high degree of alignment in polymer bonded permanent magnets are presented via the results of a study on in situ magnetic alignment of anisotropic Nd-Fe-B magnet powders. Contributions from effect of the alignment temperature, alignment magnetic field and the properties of the polymer on the hard magnetic properties of the bonded magnet were considered. The thermo-rheological properties of the polymer and the response of the magnet powders to the applied magnetic field indicate that hard magnetic properties were optimized at an alignment temperature just above the melting temperature of the EVA co-polymer. This agrees with an observed correlation between the change in magnetization due to improved magnetic alignment of the anisotropic powders and the change in viscosity of the binder. Manufacturing cost can be minimized by identifying optimum alignment temperatures and magnetic field strengths. - Highlights: • Optimum alignment of anisotropic magnet powders can enable high performance bonded magnets. • The viscoelastic state of polymer binders determines the dominating coercivity mechanism. • The minimum deviation in coercivity and remanence, with magnetic field, can occur at different temperatures. • Melting characteristics of polymer binders and the change in magnetization during alignment can be correlated.

Preparation of Fe–Si–Ni soft magnetic composites with excellent high-frequency properties

Energy Technology Data Exchange (ETDEWEB)

Xu, Wei; Wu, Chen, E-mail: chen_wu@zju.edu.cn; Yan, Mi, E-mail: mse_yanmi@zju.edu.cn

2015-05-01

Fe–Si–Ni powders were firstly prepared into soft magnetic composites (SMCs) by ball milling, surface passivation and subsequent compaction. The morphology, phase composition, and magnetic properties of the Fe–Si–Ni powders and their high-frequency performance as SMCs were investigated. The Fe–Si–Ni powders, with saturation magnetization (M{sub s}) of 254.40 emu/g after annealing, were milled down to particle sizes ranging from 40 μm to 150 μm. Surface passivation of the powders was carried out with 0.2–1.0 wt% phosphoric acid solution prior to compaction. Evolution of the high-frequency properties for the Fe–Si–Ni SMCs with the passivator concentration and the molding pressure was studied. With optimized preparation parameters, high saturation flux density (B{sub s}) of 1.23 T, stable permeability, and superior dc-bias property with a percentage permeability above 70% while H=50 Oe were achieved for the Fe–Si–Ni SMC. Minimum core loss (285 mW/cm{sup 3}) was also measured at 50 kHz for B{sub m}=50 mT. - Highlights: • Fe–Si–Ni as a new type of magnetic powder has been prepared into soft magnetic composites. • Effective surface passivation of the Fe–Si–Ni powders can be achieved by phosphate treatment. • Influence of the passivator concentration and molding pressure has been investigated. • The obtained Fe–Si–Ni soft magnetic composites exhibit excellent high-frequency performance.

Study of magnetic properties of nano-powders prepared by pyrite -> troilite transformation via high energy milling

DEFF Research Database (Denmark)

Balaz, P.; Alacova, A.; Godocikova, E.

2004-01-01

The preparation of nanocrystalline troilite by high-energy milling of FeS2 sulphide with elemental Fe acting as reducing element is reported. X-ray difractometry was used in order to determine the presence of different phases in investigated samples. This technique allowed us to identify the form......-->troilite transformation is almost finished already after 25 minutes of high-energy milling.......The preparation of nanocrystalline troilite by high-energy milling of FeS2 sulphide with elemental Fe acting as reducing element is reported. X-ray difractometry was used in order to determine the presence of different phases in investigated samples. This technique allowed us to identify...

Mechanical milling of a nano structured ductile iron powder under dry, wet and cryogenic atmospheres; Proceso de molturacion mecanica en medio seco, humedo y criogenico de polvo de hierro ductil nanoestructurado

Energy Technology Data Exchange (ETDEWEB)

Cinca, N.; Hurtado, E.; Cano, I. G.; Guilemany, J. M.

2011-07-01

The main objective of this study, is to obtain an effective particle and grain size reduction of a nano structured iron powder by mechanical milling under different milling media. One of the main challenges in this study is to work with this material of great ductility.The variables of the study to be optimized have been the following: speed of rotation, powder to ball ratio (PBR) and the percentage of control agent to induce an effective powder fracturing in front of cold welding. The powder has been characterized by a Laser Diffraction Particle Size Analyser, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and, X-ray diffraction.Through the comparative study, it is found that operating under dry milling conditions: there is a more effective particle size reduction of 43 % and grain size reduction of 62 %. In wet conditions has been reduced the amount of oxide, as well as to obtain a more homogenous distribution of the resulting powder. The results under cryogenic media is presented as promising. (Author) 15 refs.

Optimizing of SPS pressed SrFe12O19 pellets from nano-powder

DEFF Research Database (Denmark)

Mortensen, Anna; Stingaciu, Marian; Christensen, Mogens

2015-01-01

direction giving a higher net magnetization. One challenge is to optimize the pressing conditions in order to maximize the remanence and thus the energy product. In present work the SrFe12O19 powder was made in an autoclave and was analysed by X-ray diffraction and Rietveld Refinement to determine particle...... size. The powder was pressed using Spark Plasma Syntering (SPS) system at different conditions in order to investigate how the pressing conditions influence the magnetic properties. It was found, that pressing at 950oC leads to a much better alignment than pellets pressed at room temperature....... Furthermore, ball milling seems to decrease the degree of alignment and thereby the magnetic remanence which leads to a lower energy product. The magnetization was characterized using Vibrating Sample Magnetometer. By applying an external magnetic field before pressing, the alignment is heightened...

Fabrication, characterization and application of Cu{sub 2}ZnSn(S,Se){sub 4} absorber layer via a hybrid ink containing ball milled powders

Energy Technology Data Exchange (ETDEWEB)

Li, Chunran [State Key Laboratory of Superhard Materials and College of Physics, Jilin University, Changchun 130023 (China); Key Laboratory of Physics and Technology for Advanced Batteries (Ministry of Education), College of Physics, Jilin University, Changchun 130012 (China); College of Mathematics and Physics, Bohai University, Jinzhou 121013 (China); Yao, Bin, E-mail: binyao@jlu.edu.cn [State Key Laboratory of Superhard Materials and College of Physics, Jilin University, Changchun 130023 (China); Key Laboratory of Physics and Technology for Advanced Batteries (Ministry of Education), College of Physics, Jilin University, Changchun 130012 (China); Li, Yongfeng, E-mail: liyongfeng@jlu.edu.cn [Key Laboratory of Physics and Technology for Advanced Batteries (Ministry of Education), College of Physics, Jilin University, Changchun 130012 (China); Xiao, Zhenyu [State Key Laboratory of Superhard Materials and College of Physics, Jilin University, Changchun 130023 (China); Ding, Zhanhui [Key Laboratory of Physics and Technology for Advanced Batteries (Ministry of Education), College of Physics, Jilin University, Changchun 130012 (China); Zhao, Haifeng; Zhang, Ligong; Zhang, Zhenzhong [State Key Laboratory of Luminescence and Applications, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, No. 3888 Dongnanhu Road, Changchun 130033 (China)

2015-09-15

Highlights: • CZTS powders are prepared from binary sulfides by a low cost ball milling process. • Elaborated on phase evolution and formation mechanism of CZTS. • Proposed a hybrid ink approach to resolve difficulty in deposition of CZTS film. • CZTSSe solar cells with highest efficiency of 4.2% are fabricated. • Small-grained CZTS layer hinders the collection of minority carriers. - Abstract: Cu{sub 2}ZnSnS{sub 4} (CZTS) powder with kesterite structure was prepared by ball milling of mixture of Cu{sub 2}S, ZnS and SnS{sub 2} powders for more than 15 h. By dispersing the milled CZTS powder in a Cu-, Zn- and Sn-chalcogenide precursor solution, a hybrid ink was fabricated. With the hybrid ink, a precursor CZTS film was deposited on Mo coated soda-lime glass by spin-coating. In order to obtain Cu{sub 2}ZnSn(S,Se){sub 4} (CZTSSe) absorber film with kesterite structure, the CZTS film was annealed at 560 °C for 15 min in Se ambient. It is demonstrated that the annealed film is dominated by a thick layer of kesterite CZTSSe with larger grain size and Cu{sub 8}Fe{sub 3}Sn{sub 2}(S,Se){sub 12} impurity phase with the exception of a very thin layer of kesterite CZTS with smaller grain size at interface between the CZTSSe and Mo layers. Solar cell device was fabricated by using the annealed CZTSSe film as absorber layer, and its conversion efficiency reached 4.2%. Mechanism of formation of the kesterite CZTS powder and CZTSSe film as well as effect of impurity phases on conversion efficiency are discussed in the present paper. The present results suggest that the hybrid ink approach combining with ball milling is a simple, low cost and promising method for preparation of kesterite CZTSSe absorber film and CZTSSe-based solar cell.

Correlation between morphology and magnetic properties of electrochemically produced cobalt powder particles

Directory of Open Access Journals (Sweden)

Maksimović Vesna M.

2015-01-01

Full Text Available Cobalt 3D powder particles were successfully prepared by the galvanostatic electrodeposition. Electrodeposited cobalt powder were characterized by X-ray diffraction (XRD, scanning electron microscope (SEM, Energy Dispersive Spectroscopy (EDS analysis and SQUID magnetometry. It has been shown that morphology, structure and magnetic properties of cobalt particles are closely associated and can be easily controlled by adjusting process parameters of electrodeposition. Morphology of cobalt powder particles is strongly affected by hydrogen evolution reaction as a parallel reaction to cobalt electrodeposition. Depending on the applied current density, the two types of powder particles were formed: dendrites at lower and spongy-like particles at higher current densities. Morphologies and structures of powder particles are correlated with their magnetic properties, and compared with those of the bulk cobalt. In comparison with the properties of bulk cobalt, the obtained 3D structures exhibited a decreased saturation magnetization (MS, but an enhanced coercivity (HC which is explained by their peculiar morphology. [Projekat Ministarstva nauke Republike Srbije, br. III 45012

The Powdering Process with a Set of Ceramic Mills for Green Tea Promoted Catechin Extraction and the ROS Inhibition Effect

Directory of Open Access Journals (Sweden)

Kouki Fujioka

2016-04-01

Full Text Available For serving green tea, there are two prominent methods: steeping the leaf or the powdered leaf (matcha style in hot water. The purpose of the present study was to reveal chemical and functional differences before and after the powdering process of green tea leaf, since powdered green tea may contribute to expanding the functionality because of the different ingesting style. In this study, we revealed that the powdering process with a ceramic mill and stirring in hot water increased the average extracted concentration of epigallocatechin gallate (EGCG by more than three times compared with that in leaf tea using high-performance liquid chromatography (HPLC and liquid chromatography–tandem mass Spectrometry (LC-MS/MS analyses. Moreover, powdered green tea has a higher inhibition effect of reactive oxygen species (ROS production in vitro compared with the same amount of leaf tea. Our data suggest that powdered green tea might have a different function from leaf tea due to the higher catechin contents and particles.

Milling condition effects on the Nd{sub 15} Fe{sub 77} B{sub 8} powder magnetic properties; Efeito das condicoes de moagem sobre as propriedades magneticas de po de Nd{sub 15} Fe{sub 77} B{sub 8}

Energy Technology Data Exchange (ETDEWEB)

Landgraf, Fernando J.G.; Missell, Frank P

1993-12-31

As a result of the first part of a study of the development of permanent magnets, an investigation of the effect of milling on the magnetic properties of the alloy Nd{sub 15} Fe{sub 77} B{sub 8} showed differences in efficiency between ball milling and vibration milling, as well as a dependence of the intrinsic coercive field on particle size. The maximum value of the coercive field was obtained for a particle size of 1.7 {mu}m in samples compacted without magnetic orientation. (author) 9 refs., 4 figs.

Micro structrual characterization and analysis of ball milled silicon carbide

Science.gov (United States)

Madhusudan, B. M.; Raju, H. P.; Ghanaraja., S.

2018-04-01

Mechanical alloying has been one of the prominent methods of powder synthesis technique in solid state involving cyclic deformation, cold welding and fracturing of powder particles. Powder particles in this method are subjected to greater mechanical deformation due to the impact of ball-powder-ball and ball-powder-container collisions that occurs during mechanical alloying. Strain hardening and fracture of particles decreases the size of the particles and creates new surfaces. The objective of this Present work is to use ball milling of SiC powder for different duration of 5, 10, 15 and 20 hours by High energy planetary ball milling machine and to evaluate the effect of ball milling on SiC powder. Micro structural Studies using Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD) and EDAX has been investigated.

Effects of Milling Atmosphere and Increasing Sintering Temperature on the Magnetic Properties of Nanocrystalline Ni0.36Zn0.64Fe2O4

Directory of Open Access Journals (Sweden)

Abdollah Hajalilou

2015-01-01

Full Text Available Nanocrystalline Ni0.36Zn0.64Fe2O4 was synthesized by milling a powder mixture of Zn, NiO, and Fe2O3 in a high-energy ball mill for 30 h under three different atmospheres of air, argon, and oxygen. After sintering the 30 h milled samples at 500°C, the XRD patterns suggested the formation of a single phase of Ni-Zn ferrite. The XRD results indicated the average crystallite sizes to be 15, 14, and 16 nm, respectively, for the 30 h milled samples in air, argon, and oxygen atmospheres sintered at 500°C. From the FeSEM micrographs, the average grain sizes of the mentioned samples were 83, 75, and 105 nm, respectively, which grew to 284, 243, and 302 nm after sintering to 900°C. A density of all the samples increased while a porosity decreased by elevating sintering temperature. The parallel evolution of changes in magnetic properties, due to microstructural variations with changes in the milling atmosphere and sintering temperature in the rage of 500–900°C with 100°C increments, is also studied in this work.

Effect Of DyMn Alloy-Powder Addition On Microstructure And Magnetic Properties Of NdFeB Sintered Magnets

Directory of Open Access Journals (Sweden)

Lee M.-W.

2015-06-01

Full Text Available Micostructural change and corresponding effect on coercivity of a NdFeB sintered magnet mixed with small amount of DyMn powder was investigated. In the sintered magnet mixed with the DyMn alloy-powder Dy-rich shell was formed at outer layer of the main grains, while Mn was mostly concentrated at Nd-rich triple junction phase (TJP, lowering melting temperature of the Nd-rich phase that eventually improved the microstructural characteristics of the gain boundary phase. The coercivity of a magnet increased more than 3.5 kOe by the mixing of the DyMn alloy-powder.

Magnetic properties of Ni nanoparticles dispersed in silica prepared by high-energy ball milling

Science.gov (United States)

González, E. M.; Montero, M. I.; Cebollada, F.; de Julián, C.; Vicent, J. L.; González, J. M.

1998-04-01

We analyze the magnetic properties of mechanically ground nanosized Ni particles dispersed in a SiO2 matrix. Our magnetic characterization of the as-milled samples show the occurrence of two blocking processes and that of non-monotonic milling time evolutions of the magnetic-order temperature, the high-field magnetization and the saturation coercivity. The measured coercivities exhibit giant values and a uniaxial-type temperature dependence. Thermal treatment carried out in the as-prepared samples result in a remarkable coercivity reduction and in an increase of the high-field magnetization. We conclude, on the basis of the consideration of a core (pure Ni) and shell (Ni-Si inhomogeneous alloy) particle structure, that the magnetoelastic anisotropy plays the dominant role in determining the magnetic properties of our particles.

N-type nano-silicon powders with ultra-low electrical resistivity as anode materials in lithium ion batteries

Science.gov (United States)

Yue, Zhihao; Zhou, Lang; Jin, Chenxin; Xu, Guojun; Liu, Liekai; Tang, Hao; Li, Xiaomin; Sun, Fugen; Huang, Haibin; Yuan, Jiren

2017-06-01

N-type silicon wafers with electrical resistivity of 0.001 Ω cm were ball-milled to powders and part of them was further mechanically crushed by sand-milling to smaller particles of nano-size. Both the sand-milled and ball-milled silicon powders were, respectively, mixed with graphite powder (silicon:graphite = 5:95, weight ratio) as anode materials for lithium ion batteries. Electrochemical measurements, including cycle and rate tests, present that anode using sand-milled silicon powder performed much better. The first discharge capacity of sand-milled silicon anode is 549.7 mAh/g and it is still up to 420.4 mAh/g after 100 cycles. Besides, the D50 of sand-milled silicon powder shows ten times smaller in particle size than that of ball-milled silicon powder, and they are 276 nm and 2.6 μm, respectively. In addition, there exist some amorphous silicon components in the sand-milled silicon powder excepting the multi-crystalline silicon, which is very different from the ball-milled silicon powder made up of multi-crystalline silicon only.

Particle and powder characterisation of Bi-based superconductors

International Nuclear Information System (INIS)

Yavuz, M.; Guo, Y. C.; Liu, H. L.; Dou, S. X.; Vance, E. R.

1996-01-01

Full text: Superconductor precursor powder was ground in a planetary and an attrition mill using various combinations of grinding container, balls and carrier (dry and wet). Dry milling was found to be more effective than wet milling for reducing particle size irrespective of container and ball materials used in the planetary milling. On the other hand, wet milling was found more effective in the attrition milling. Serious Si contamination was observed in powders milled using agate grinding materials. Some C from polypropylene container was found after milling, but no Zr from YSZ balls. Effect of particle size on the property of Bi 2223/Ag tapes was investigated in terms of critical current density (J c ). Fine particle size was found to show high J c

Liquid phase surface melting of AA8011 aluminum alloy by addition of Al/Al{sub 2}O{sub 3} nano-composite powders synthesized by high-energy milling

Energy Technology Data Exchange (ETDEWEB)

Sohi, M. Heydarzadeh [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Hojjatzadeh, S.M.H., E-mail: Hojatzadeh@yahoo.com [Department of Welding, Science and Research Branch, Azad University, Tehran (Iran, Islamic Republic of); Moosavifar, Sh. S.; Heshmati-Manesh, S. [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran (Iran, Islamic Republic of)

2014-09-15

Highlights: • Aluminum matrix composite layers reinforced with alumina particles were fabricated. • Non milled powders caused porosity in the microstructures because of poor wettability. • The ball milling of powders was significantly improved the wettability of nano ceramic particles. • The micro hardness of the layers was approximately 3 times greater than that of the base metal. - Abstract: Poor wettability of particles is an obstacle in formation of sound composite layer via surface melting. Pre-coating of particles with metallic material by different techniques, such as ball milling may enhance the wettability of the particles with molten metal. In this study, composite surface layers containing Al{sub 2}O{sub 3} particles were fabricated on the surface of AA8011 aluminum substrates by tungsten inert gas (TIG) surface melting using preplaced layers of Al/Al{sub 2}O{sub 3} powder mixtures in two different forms: (1) a mixture of 40 wt% Al and 60 wt% of 50 nm Al{sub 2}O{sub 3} powders and (2) a mixture obtained by mechanical alloying of 40 wt% Al and 60 wt% of 60 μm Al{sub 2}O{sub 3} powders. Morphology evolution of powders during ball milling and the microstructure of the fabricated composite layers were studied through conventional characterization techniques, such as optical microscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD). Microhardness measurements were also performed across the alloyed zone. The results indicated that the layer fabricated by the second route showed a defect free structure with a more uniform distribution of Al{sub 2}O{sub 3} particles in comparison with the layer obtained by the first route. It was also noticed that the uniform dispersion of Al{sub 2}O{sub 3} particles in the fabricated layer increased the hardness to 133 HV which was over 3 times of that of the base metal.

Rare earth metal alloy magnets

International Nuclear Information System (INIS)

Harris, I.R.; Evans, J.M.; Nyholm, P.S.

1979-01-01

This invention relates to rare earth metal alloy magnets and to methods for their production. The technique is based on the fact that rare earth metal alloys (for e.g. cerium or yttrium) which have been crumbled to form a powder by hydride formation and decomposition can be used for the fabrication of magnets without the disadvantages inherent in alloy particle size reduction by mechanical milling. (UK)

Removing metal debris from thermosetting EMC powders by Nd-Fe-B permanent magnets

Directory of Open Access Journals (Sweden)

Liaw Yowching

2017-01-01

Full Text Available During the preparation of thermosetting encapsulation molding compounds (EMCs for semiconductor packaging, metal debris are always present in the EMC powders due to the hard silica fillers in the compound. These metal debris in the EMC powders will cause circuit shortage and therefore have to be removed before molding. In this study, Nd-Fe-B permanent magnets are used to remove these debris. The results show that the metal debris can be removed effectively as the rate of accumulation of the metal debris increases as time proceeds in the removing operation. The removal effectiveness of the debris is affected by both the magnetic flux density and the flow around the magnet. The wake flow behind the magnet is a relatively low speed recirculation region which facilities the attraction of metal debris in the powders. Thus, the largest amount of the accumulated EMC powders occurs downstream of the magnet. Hence, this low speed recirculation region should be better utilized to enhance the removal efficiency of the metal debris.

Magnetic structure evolution in mechanically milled nanostructured ZnFe2O4 particles

DEFF Research Database (Denmark)

Jiang, Jianzhong; Wynn, P.; Mørup, Steen

1999-01-01

Nanostructured partially-inverted ZnFe2O4 particles have been prepared from bulk ZnFe2O4 by high-energy ball milling in an open container. The grain size reduction, cation site distributions, and the evolution of magnetic structures have been studied by x-ray diffraction with Rietveld structure...... refinements, transmission electron microscopy, and Mossbauer spectroscopy. It is found that a change of magnetic structure from an antiferromagnetic to a ferrimagnetic (or ferromagnetic) structure occurs in the milled samples. This change is correlated with the redistribution of the cations, Zn and Fe...

Studies on the structure of zirconium carbide powders subjected to vibration grinding

International Nuclear Information System (INIS)

Kravchik, A.E.; Neshpor, V.S.

1976-01-01

The present work is a study of zirconium carbide powders subjected to vibratory milling in various media. The powders were comminuted in air (dry milling), benzene, trichloroethylene, and distilled water. The milling time was 10-160 h. The chemical compositions, specific surfaces, and crystal lattice parameters of the powder in the initial condition and after milling for 100 h in the various media are given. Vibratory milling of zirconium carbide powder can be successfully performed in benzene. Comminution in benzene enables a large specific surface to be attained, with practically no chemical reaction between the medium and the milling products. In milling in trichloroethylene the latter decomposes, with the formation of hydrochloric acid which reacts with the milling products. In a study of the fine structure parameters of zirconium carbide in the , , and directions the smallest crystal lattice strains and block sizes were observed in the direction. This may be taken as evidence that under such disintegration conditions the (110) planes constitute cleavage planes. An evaluation of internal and surface energies established that the strained crystal lattice energy reaches values which must be allowed for in any subsequent uses of the powder

Effect of Powder Grain Size on Microstructure and Magnetic Properties of Hexagonal Barium Ferrite Ceramic

Science.gov (United States)

Shao, Li-Huan; Shen, Si-Yun; Zheng, Hui; Zheng, Peng; Wu, Qiong; Zheng, Liang

2018-05-01

Compact hexagonal barium ferrite (BaFe12O19, BaM) ceramics with excellent magnetic properties have been prepared from powder with the optimal grain size. The dependence of the microstructure and magnetic properties of the ceramics on powder grain size was studied in detail. Single-phase hexagonal barium ferrite powder with grain size of 177 nm, 256 nm, 327 nm, and 454 nm was obtained by calcination under different conditions. Scanning electron microscopy revealed that 327-nm powder was beneficial for obtaining homogeneous grain size and compact ceramic. In addition, magnetic hysteresis loops and complex permeability spectra demonstrated that the highest saturation magnetization (67.2 emu/g) and real part of the permeability (1.11) at 1 GHz were also obtained using powder with grain size of 327 nm. This relationship between the powder grain size and the properties of the resulting BaM ceramic could be significant for development of microwave devices.

Artificial neural network methodology: Application to predict magnetic properties of nanocrystalline alloys

International Nuclear Information System (INIS)

Hamzaoui, R.; Cherigui, M.; Guessasma, S.; ElKedim, O.; Fenineche, N.

2009-01-01

This paper is dedicated to the optimization of magnetic properties of iron based magnetic materials with regard to milling and coating process conditions using artificial neural network methodology. Fe-20 wt.% Ni and Fe-6.5 wt.% Si, alloys were obtained using two high-energy ball milling technologies, namely a planetary ball mill P4 vario ball mill from Fritsch and planetary ball mill from Retch. Further processing of Fe-Si powder allowed the spraying of the feedstock material using high-velocity oxy-fuel (HVOF) process to obtain a relatively dense coating. Input parameters were the disc Ω and vial ω speed rotations for the milling technique, and spray distance and oxygen flow rate in the case of coating process. Two main magnetic parameters are optimized namely the saturation magnetization and the coercivity. Predicted results depict clearly coupled effects of input parameters to vary magnetic parameters. In particular, the increase of saturation magnetization is correlated to the increase of the product Ωω (shock power) and the product of spray parameters. Largest coercivity values are correlated to the increase of the ratio Ω/ω (shock mode process) and the increase of the product of spray parameters.

High field surface magnetic study of Fe{sub 3}O{sub 4} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Kihal, A. [Laboratoire de Magnetisme et Spectroscopie des Solides (LM2S), Universite Badji Mokhtar, BP-12 Annaba (Algeria); LNCMI-G, CNRS-UJF, 25 Rue des Martyrs, BP-166, 38042 Grenoble-Cedex 9 (France); Fillion, G. [LNCMI-G, CNRS-UJF, 25 Rue des Martyrs, BP-166, 38042 Grenoble-Cedex 9 (France); Bouzabata, B. [Laboratoire de Magnetisme et Spectroscopie des Solides (LM2S), Universite Badji Mokhtar, BP-12 Annaba (Algeria); Barbara, B. [Institut Neel, CNRS-UJF, 25 Rue des Martyrs, BP-166, 38042 Grenoble-Cedex 9 (France)

2012-03-15

Magnetic properties of magnetite (Fe{sub 3}O{sub 4}) powders, milled for various times up to 15 h, are studied by magnetization measurements. For the starting powder, like in the bulk single crystal, the approach to magnetic saturation is mainly ruled by the usual 1/H and 1/H{sup 2} terms. But for the milled samples, as the grain size decreases, a 1/H{sup 1/2} term rises as the leading term and is interpreted in the framework of the theory of Chudnovsky et al. accounting for the effect of a random anisotropy generated near the surface, aside from a large constant high field susceptibility related to the canted spins at the surface. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Analysis of crystallite size and microdeformation crystal lattice the tungsten carbide milling in mill high energy

International Nuclear Information System (INIS)

Silva, F.T. da; Nunes, M.A.M.; Souza, C.P. de; Gomes, U.U.

2010-01-01

The tungsten carbide (WC) has wide application due to its properties like high melting point, high hardness, wear resistance, oxidation resistance and good electrical conductivity. The microstructural characteristics of the starting powders influences the final properties of the carbide. In this context, the use of nanoparticle powders is an efficient way to improve the final properties of the WC. The high energy milling stands out from other processes to obtain nanometric powders due to constant microstructural changes caused by this process. Therefore, the objective is to undertake an analysis of microstructural characteristics on the crystallite size and microdeformations of the crystal lattice using the technique of X-ray diffraction (XRD) using the Rietveld refinement. The results show an efficiency of the milling process to reduce the crystallite size, leading to a significant deformation in the crystal lattice of WC from 5h milling. (author)

MILLING MECHANICS OF MATERIALS ROLLED IN THICK LAYER

Directory of Open Access Journals (Sweden)

E. B. Lojechnikov

2006-01-01

Full Text Available Powder rolling conditions are systematized with the purpose of their compacting and milling. The generalized  condition of solid and free-flowing bulk material deformation is proposed in the  paper. The analytical solution of a stressed state of powder being shaped mechanically that ensures milling of its particles has been obtained.

Effect of process variables on synthesis of MgB2 by a high energy ball mill

Directory of Open Access Journals (Sweden)

Kurama Haldun

2016-01-01

Full Text Available The discovery of superconductivity of MgB2 in 2001, with a critical temperature of 39 K, offered the promise of important large-scale applications at around 20 K. Except than the other featured synthesis methods, mechanical activation performed by high energy ball mills, as bulk form synthesis or as a first step of wire and thin film productions, has considered as an effective alternative production route in recent years. The process of mechanical activation (MA starts with mixing the powders in the right proportion and loading the powder mixture into the mill with the grinding media. The milled powder is then consolidated into a bulk shape and heat-treated to obtain desired microstructure and properties. Thus, the important components of the MA process are the raw materials, mill type and process variables. During the MA process, heavy deformation of particles occure. This is manifested by the presence of a variety of crystal defects such as dislocations, vacancies, stacking faults and increased number of particle boundaries. The presence of this defect structure enhances the diffusivity of solute hence the critical currents and magnetic flux pinning ability of MgB2 are improved. The aim of the present study is to determine the effects of process variables such as ball-to-powder mass ratio, size of balls, milling time, annealing temperature and contribution of process control agent (toluene on the product size, morphology and conversion level of precursor powders to MgB2 after subsequent heat treatment. The morphological analyses of the samples were performed by a high vacuum electron microscope ZEISS SUPRA VP 50. The phase compositions of the samples were performed with an Rigaku-Rint 2200 diffractometer, with nickel filtered Cu Kα radiation and conversion level. The MgB2 phase wt % was calculated by the Rietveld refinement method. The obtained results were discussed according to the process variables to find out their affect on the structure

The influence of carbon and oxygen on the magnetic characteristics of press-less sintered NdFeB magnets

International Nuclear Information System (INIS)

Xia, M.; Abrahamsen, A.B.; Bahl, C.R.H.; Veluri, B.; Søegaard, A.I.; Bøjsøe, P.; Millot, S.

2017-01-01

The Pressless Process (PLP) was adopted to manufacture NdFeB sintered magnets, where the investigations on carbon and oxygen residues from heptane milling liquid media and graphite crucibles used for sintering were quantified to evaluate the influence on the magnetic characteristics. The carbon and oxygen content in the magnets produced from wet ball milling of strip cast flakes was found to be of the order 10 4 ppm and 4·10 4 ppm respectively, which resulted in soft magnetic behavior. However using jet milling the carbon and oxygen concentration were decreased by an order of magnitude resulting in coercivity of up to 829 kA/m. Thus the influence of the carbon from the graphite crucibles is small. - Highlights: • It is found that the carbon from graphite crucibles will not influence the NdFeB. • The carbon from heptane mixed with NdFeB powder will react with the NdFeB, which breaks the magnetic properties of NdFeB. • Pressless process works well with graphite crucibles, without worrying that carbon has damage on magnets.

The influence of carbon and oxygen on the magnetic characteristics of press-less sintered NdFeB magnets

Energy Technology Data Exchange (ETDEWEB)

Xia, M., E-mail: maxi@dtu.dk [Department of Energy Conversion and Storage, DTU Risø Campus, Technical University of Denmark, Roskilde (Denmark); Abrahamsen, A.B. [Department of Wind Energy, DTU Risø campus, Technical University of Denmark, Roskilde (Denmark); Bahl, C.R.H. [Department of Energy Conversion and Storage, DTU Risø Campus, Technical University of Denmark, Roskilde (Denmark); Veluri, B.; Søegaard, A.I. [Grundfos A/S, DK-8850 Bjerringbro (Denmark); Bøjsøe, P. [Holm Magnetics APS, 2800 Kongens Lyngby (Denmark); Millot, S. [FJ Industries A/S, 5863 Ferritslev (Denmark)

2017-01-15

The Pressless Process (PLP) was adopted to manufacture NdFeB sintered magnets, where the investigations on carbon and oxygen residues from heptane milling liquid media and graphite crucibles used for sintering were quantified to evaluate the influence on the magnetic characteristics. The carbon and oxygen content in the magnets produced from wet ball milling of strip cast flakes was found to be of the order 10{sup 4} ppm and 4·10{sup 4} ppm respectively, which resulted in soft magnetic behavior. However using jet milling the carbon and oxygen concentration were decreased by an order of magnitude resulting in coercivity of up to 829 kA/m. Thus the influence of the carbon from the graphite crucibles is small. - Highlights: • It is found that the carbon from graphite crucibles will not influence the NdFeB. • The carbon from heptane mixed with NdFeB powder will react with the NdFeB, which breaks the magnetic properties of NdFeB. • Pressless process works well with graphite crucibles, without worrying that carbon has damage on magnets.

Line profile analysis of ODS steels Fe20Cr5AlTiY milled powders at different Y2O3 concentrations

Science.gov (United States)

Afandi, A.; Nisa, R.; Thosin, K. A. Z.

2017-04-01

Mechanical properties of material are largely dictated by constituent microstructure parameters such as dislocation density, lattice microstrain, crystallite size and its distribution. To develop ultra-fine grain alloys such as Oxide Dispersion Strengthened (ODS) alloys, mechanical alloying is crucial step to introduce crystal defects, and refining the crystallite size. In this research the ODS sample powders were mechanically alloyed with different Y2O3 concentration respectively of 0.5, 1, 3, and 5 wt%. MA process was conducted with High Energy Milling (HEM) with the ball to powder ratio of 15:1. The vial and the ball were made of alumina, and the milling condition is set 200 r.p.m constant. The ODS powders were investigated by X-Ray Diffractions (XRD), Bragg-Brentano setup of SmartLab Rigaku with 40 KV, and 30 mA, step size using 0.02°, with scanning speed of 4°min-1. Line Profile Analysis (LPA) of classical Williamson-Hall was carried out, with the aim to investigate the different crystallite size, and microstrain due to the selection of the full wide at half maximum (FWHM) and integral breadth.

Surface effects on the magnetic behavior of nanocrystalline nickel ferrites and nickel ferrite-polymer nanocomposites

International Nuclear Information System (INIS)

Nathani, H.; Misra, R.D.K.

2004-01-01

The magnetization studies on nanocrystalline nickel ferrite as powder particles, and as diluted dispersion (10 wt.%) in polymer matrix (polymer nanocomposites) are presented. The two polymer-based nanocomposites were prepared via ball-milling and in situ polymerization, respectively. The magnetization measurements provide strong evidence of surface effects to magnetization, which explains the non-saturation of magnetization at high fields. The differences in the magnetization behavior of nickel ferrite as powder particles and in the ball-milled nanocomposite and the nanocomposite prepared via in situ polymerization are attributed to the different extent of interparticle interactions between the particles and the preparation route. The magnetization versus applied field behavior of the three ferrite systems show a similar jump in the initial part of the magnetization curve in all the cases which implies the existence of a core-shell like morphology of the particles over a large temperature range and its dominance over the interparticle interaction effects between the particles

Magnetic response of superconducting mesoscopic-size YBCO powder

Energy Technology Data Exchange (ETDEWEB)

Deimling, C.V. [Grupo de Supercondutividade e Magnetismo, Departamento de Fisica, Universidade Federal de Sao Carlos, Sao Carlos, SP (Brazil)], E-mail: cesard@df.ufscar.br; Motta, M.; Lisboa-Filho, P.N. [Laboratorio de Materiais Supercondutores, Departamento de Fisica, Universidade Estadual Paulista, Bauru, SP Brazil (Brazil); Ortiz, W.A. [Grupo de Supercondutividade e Magnetismo, Departamento de Fisica, Universidade Federal de Sao Carlos, Sao Carlos, SP (Brazil)

2008-07-15

In this work it is reported the magnetic behavior of submicron and mesoscopic-size superconducting YBCO powders, prepared by a modified polymeric precursors method. The grain size and microstructure were analyzed using scanning electron microscopy (SEM). Measurements of magnetization and AC-susceptibility as a function of temperature were performed with a quantum design SQUID magnetometer. Our results indicated significant differences on the magnetic propreties, in connection with the calcination temperature and the pressure used to pelletize the samples. This contribution is part of an effort to study vortex dynamics and magnetic properties of submicron and mesoscopic-size superconducting samples.

Tungsten-nanodiamond composite powders produced by ball milling

Energy Technology Data Exchange (ETDEWEB)

Nunes, D., E-mail: daniela.nunes@ist.utl.pt [Associacao Euratom/IST, Instituto de Plasmas e Fusao Nuclear, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); ICEMS, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Livramento, V. [Associacao Euratom/IST, Instituto de Plasmas e Fusao Nuclear, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); Mardolcar, U.V. [Departamento de Fisica, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Centro de Ciencias Moleculares e Materiais, Faculdade de Ciencias da Universidade de Lisboa, Campo Grande, 1749-016 Lisboa (Portugal); Correia, J.B. [LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); Carvalho, P.A. [ICEMS, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Departamento de Bioengenharia, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)

2012-07-15

The major challenge in producing tungsten-nanodiamond composites by ball milling lies in successfully dispersing carbon nanoparticles in the metallic matrix while keeping carbide formation at a minimum. Processing windows for carbide minimization have been established through systematic variation of the nanodiamond fraction, milling energy and milling time. Materials characterization has been carried out by X-ray diffraction, scanning and transmission electron microscopy and microhardness testing. Nanostructured matrices with homogeneously dispersed particles that preserved the diamond structure have been produced. Differential thermal analysis has been used to evaluate the composites thermal stability.

Recoilless Factors in Nanostructured Iron-Based Powders

International Nuclear Information System (INIS)

Guerault, H.; Labaye, Y.; Greneche, J.-M.

2001-01-01

57 Fe Moessbauer spectrometry was carried out on high-energy ball-milled crystalline compounds in order to study the milling effect on the Lamb-Moessbauer factor f. A comparison between metallic (α-Fe) and ionic (r-FeF 3 ) milled powders is proposed, evidencing different milling mechanisms. In the case of the ionic system, a notable enhancement of the f factor at 77 K is observed by freezing the powder into a resin. This suggests that, in addition to nanostructured aggregated particles, the milling procedure favours the obtention of isolated nanoparticles, the sizes of which are smaller than the critical size for the observation of the Moessbauer effect. In return, in the case of the metallic system, the absorption gain due to the embedding is much smaller, probably due to a better re-agglomeration of the metallic particles during the milling process

Wet milling versus co-precipitation in magnetite ferrofluid preparation

Directory of Open Access Journals (Sweden)

Almásy László

2015-01-01

Full Text Available Various uses of ferrofluids for technical applications continuously raise the interest in improvement and optimization of preparation methods. This paper deals with preparation of finely granulated magnetite particles coated with oleic acid in hydrocarbon suspensions following either chemical co-precipitation from iron salt precursors or wet milling of micron size magnetite powder with the goal to compare the benefits and disadvantages of each method. Microstructural measurements showed that both methods gave similar magnetite particle size of 10-15 nm. Higher saturation magnetization was achieved for the wet-milled magnetite suspension compared to relatively rapid co-precipitation synthesis. Different efficacies of ferrophase incorporation into kerosene could be related to the different mechanisms of oleic acid bonding to nanoparticle surface. The comparative data show that wet milling represents a practicable alternative to the traditional co-precipitation since despite of longer processing time, chemicals impact on environment can be avoided as well as the remnant water in the final product.

Broadband magnetic losses of nanocrystalline ribbons and powder cores

Energy Technology Data Exchange (ETDEWEB)

Beatrice, Cinzia, E-mail: c.beatrice@inrim.it [Istituto Nazionale di Ricerca Metrologica, Nanoscience and Materials Division, Torino (Italy); Dobák, Samuel [Institute of Physics, Faculty of Science, P.J. Šafárik University, Košice (Slovakia); Ferrara, Enzo; Fiorillo, Fausto [Istituto Nazionale di Ricerca Metrologica, Nanoscience and Materials Division, Torino (Italy); Ragusa, Carlo [Politecnico di Torino, Energy Department, Torino (Italy); Füzer, Ján; Kollár, Peter [Institute of Physics, Faculty of Science, P.J. Šafárik University, Košice (Slovakia)

2016-12-15

Finemet type alloys have been investigated from DC to 1 GHz at different induction levels upon different treatments: as amorphous precursors, as ribbons nanocrystallized with and without an applied saturating field, as consolidated powders. The lowest energy losses at all frequencies and maximum Snoek's product are exhibited by the transversally field-annealed ribbons. This is understood in terms of rotation-dominated magnetization process in the low-anisotropy material. Intergrain eddy currents are responsible for the fast increase of the losses with frequency and for early permeability relaxation of the powder cores. Evidence for resonant phenomena at high frequencies and for the ensuing inadequate role of the static magnetic constitutive equation of the material in solving the magnetization dynamics via the Maxwell's diffusion equation of the electromagnetic field is provided. It is demonstrated that, by taking the Landau–Lifshitz–Gilbert equation as a constitutive relation, the excellent frequency response of the transverse anisotropy ribbons can be described by analytical method.

Process variables in the obtention of U-Mo powder by the hydriding-milling-dehydriding method (HMD process)

International Nuclear Information System (INIS)

Pasqualini, Enrique E.; Helzel Garcia, Javier; Lopez, Marisol

2003-01-01

In the next few years nuclear fuels based on uranium oxides, aluminides and silicides for MTR reactors will be replaced by the high density alloy uranium- 7% (w/w) molybdenum (U-7 Mo). Actually there is only one commercial supplier of this raw material that has to be provided as powder containing 20% enriched uranium ( 235 U). In the Nuclear Fuels Department of the National Atomic Energy Commission (CNEA) at Buenos Aires was developed an alternative way of producing U-7 Mo powder in a production scale. Meanwhile CNEA is participating in the International Program (RERTR) for final qualification of this nuclear material. This new method of production consists in the hydriding of the alloy, milling the hydride to final size and dehydriding the powder. These results were achieved because a special technique was discovered for the massive hydriding of the U-7 Mo alloy. The production method is simple, requires conventional equipment and low investment. Argentine can have important comparative advantages for its production and exportation. A scale production plant is being planed. (author)

Microstructural characteristics and mechanical properties of carbon nanotube reinforced aluminum alloy composites produced by ball milling

International Nuclear Information System (INIS)

Raviathul Basariya, M.; Srivastava, V.C.; Mukhopadhyay, N.K.

2014-01-01

Highlights: • 6082 Al alloy composite with 2 wt% multiwalled carbon nanotubes prepared by milling. • Effect of milling time on structure and property evolution has been studied. • The reinforced composite powders showed a drastic crystallite size refinement. • The presence of carbon nanotube led to a two fold increase in the hardness and modulus. • The composite powder showed good thermal stability studied by DTA. - Abstract: The influence of milling time on the structure, morphology and thermal stability of multi-walled carbon nanotubes (MWCNTs) reinforced EN AW6082 aluminum alloy powders has been studied. After structural and microstructural characterization of the mechanically milled powders micro- and nano-hardness of the composite powder particles were evaluated. The morphological and X-ray diffraction studies on the milled powders revealed that the carbon nanotubes (CNTs) were uniformly distributed and embedded within the aluminum matrix. No reaction products were detected even after long milling up to 50 h. Nanotubes became shorter in length as they fractured under the impact and shearing action during the milling process. A high hardness of about 436 ± 52 HV is achieved for the milled powders, due to the addition of MWCNTs, after milling for 50 h. The increased elastic modulus and nanohardness can be attributed to the finer grain size evolved during high energy ball milling and to the uniform distribution of hard CNTs in the Al-alloy matrix. The hardness values of the composite as well as the matrix alloy compares well with that predicted by the Hall–Petch relationship

Spray drying of beryllium oxide powder

International Nuclear Information System (INIS)

Sepulveda, J.L.; Kahler, D.A.

1991-01-01

Forming of beryllia ceramics through dry pressing requires the agglomeration of the powder through spray drying. To produce high quality fired ceramics it is necessary to disperse/grind the primary powder prior to binder addition. Size reduction of the powder is accomplished using an aqueous system in Vibro-Energy mills (VEM) charged with beryllia media to minimize contamination. Two VEM mills of different size were used to characterize the grinding operation. Details of the grinding kinetics are described within the context of the Macroscopic Population Balance Model approach. Spray drying of the ceramic slurry was accomplished with both a centrifugal atomizer and a two fluid nozzle atomizer. Two different spray dryers were used. Important operating parameters affecting the size distribution of the spray dried powder are discussed

Application of a hydrogenation to production of the Nd sub 2 Fe sub 14 B permanent magnet

Energy Technology Data Exchange (ETDEWEB)

Choi, Jeon; Park, Choong Nyeon; Choi, Dap Chun [Chonnam National Univ., Kwangju (Republic of Korea)

1989-12-01

Powders of bulk ingot of Nd-Fe-B permanent magnet were prepared by a combination of hydrogenation and mechanical milling. In-situ observation revealed that cracks, during hydrogenation, were initiated at the grain bounderies where Nd-rich phases existed and then propagated into the matrix Nd{sub 2}Fe{sub 14}B phase. The powders were aligned and pressed in the hydrided condition and the green compacts were sintered at 1100 deg C for 1 hr, followed by heat treatment at 600 deg C for 1 hr. The maximum value of the (BH){sub max} of 37 MGOe was obtained with the sample which was planetary ball milled for 18 min after the hydrogenation at 13 atm. This value of (BH){sub max} is comparable with that of the magnets produced by mechanical milling only. (Author).

Microstructure, magnetic and Moessbauer studies on spark-plasma sintered Sm-Co-Fe/Fe(Co) nanocomposite magnets

Energy Technology Data Exchange (ETDEWEB)

Rao, N V Rama; Saravanan, P; Gopalan, R; Raja, M Manivel; Rao, D V Sreedhara; Chandrasekaran, V [Defence Metallurgical Research Laboratory, Hyderabad-500 058 (India); Sivaprahasam, D [International Advanced Research Centre for Powder Metallurgy and New Materials Hyderabad-500 005 (India); Ranganathan, R [Saha Institute of Nuclear Physics, Kolkata-700 064 (India)], E-mail: rg_gopy@yahoo.com

2008-03-21

Nanocomposite powders comprising Sm-Co-Fe intermetallic phases and Fe(Co) were synthesized by high-energy ball milling and were consolidated into bulk magnets by the spark-plasma sintering (SPS) technique. While the microstructure of the SPS samples was characterized by transmission electron microscopy (TEM), the solubility of Fe in different phases was investigated using Moessbauer spectroscopy. TEM studies revealed that the spark-plasma sintered sample has Sm(Co,Fe){sub 5} as a major phase with Sm{sub 2}(Co,Fe){sub 17}, Sm(Co,Fe){sub 2} and Fe(Co) as secondary phases. The size of the nanocrystalline grains of all these phases was found to be in the range 50-100 nm. The Moessbauer spectra of the as-milled powders exhibited two different subspectra: a sextet corresponding to the Fe phase and a broad sextet associated with the Fe(Co) phase; while that of the SPS sample showed four different subspectra: a sextet corresponding to Fe and other three sextets corresponding to the Fe(Co), Sm(Co,Fe){sub 5} and Sm{sub 2}(Co,Fe){sub 17} phases; these results are in accordance with the TEM observation. Recoil magnetization and reversible susceptibility measurements revealed magnetically single phase behaviour of the SPS magnets.

Microstructural analysis of sinterized aluminum powder obtained by the high energy milling of beverage cans; Analise microestrutural de po de aluminio sinterizado obtido pela moagem de alta energia de latas de bebidas

Energy Technology Data Exchange (ETDEWEB)

Souza, Jose Raelson Pereira de; Peres, Mauricio Mhirdaui, E-mail: mauricioperes@ct.ufrn.br [Universidade Federal do Rio Grande do Norte (UFRN), RN (Brazil)

2016-07-01

The objective is the study of the effect of high energy milling on the sintering of aluminum from beverage cans. The selected aluminum cans were cut and subjected to high energy milling under a common atmosphere (in the air). In milling, three grams of aluminum was used to maintain the ratio of 10/1 between the mass of the beads and the material. The milling time was varied in 1h, 1.5h and 2h, keeping the other variables constant. The particle size distribution was measured by laser granulometry, for further compaction and sintering at a temperature of 600 ° C for 2 h. The samples were characterized by scanning electron microscopy (SEM). The granulometric analysis of the powders found that higher milling times produced finer particles. Powders with granulometry of less than 45 μm were obtained at 1 h, 1.5 h and 2 h times. The times of 1.5h and 2h promoted finer particles with better distribution of size. The SEM analyzes showed little variation in the shape of the particles as a function of the variation of the grinding times, presenting irregularities in the platelet geometry. The sintering time and temperature were effective in the densification of the powder particles, which were influenced by the average particle size.

Development of MnBi permanent magnet: Neutron diffraction of MnBi powder

Energy Technology Data Exchange (ETDEWEB)

Cui, J., E-mail: jun.cui@pnnl.gov; Choi, J. P.; Li, G.; Polikarpov, E.; Darsell, J. [Energy and Environment Directorate, Pacific Northwest National Laboratory, Richland, Washington 99354 (United States); Kramer, M. J.; Zarkevich, N. A.; Wang, L. L.; Johnson, D. D. [Materials Sciences and Engineering Division, Ames Laboratory, Ames, Iowa 50011 (United States); Marinescu, M. [Electron Energy Corporation, Landisville, Pennsylvania 17538 (United States); Huang, Q. Z.; Wu, H. [NIST Center for Neutron Research, National Institute of Standards and Technology, Gaithersburg, Maryland 20899-6102 (United States); Vuong, N. V.; Liu, J. P. [Department of Physics, University of Texas at Arlington, Arlington, Texas 76019 (United States)

2014-05-07

MnBi attracts great attention in recent years for its great potential as permanent magnet materials. MnBi phase is difficult to obtain because of the rather drastic peritectic reaction between Mn and Bi. In this paper, we report our effort on synthesizing high purity MnBi compound using conventional powder metallurgical approaches. Neutron diffraction was carried out to investigate the crystal and nuclear structure of the obtained powder. The result shows that the purity of the obtained powder is about 91 wt. % at 300 K, and the magnetic moment of the Mn atom in MnBi lattice is 4.424 and 4.013 μ{sub B} at 50 K and 300 K, respectively.

Development of MnBi permanent magnet: Neutron diffraction of MnBi powder

Energy Technology Data Exchange (ETDEWEB)

Cui, J; Choi, JP; Li, G; Polikarpov, E; Darsell, J; Kramer, MJ; Zarkevich, NA; Wang, LL; Johnson, DD; Marinescu, M; Huang, QZ; Wu, H; Vuong, NV; Liu, JP

2014-05-07

MnBi attracts great attention in recent years for its great potential as permanent magnet materials. MnBi phase is difficult to obtain because of the rather drastic peritectic reaction between Mn and Bi. In this paper, we report our effort on synthesizing high purity MnBi compound using conventional powder metallurgical approaches. Neutron diffraction was carried out to investigate the crystal and nuclear structure of the obtained powder. The result shows that the purity of the obtained powder is about 91 wt. % at 300 K, and the magnetic moment of the Mn atom in MnBi lattice is 4.424 and 4.013 mu(B) at 50 K and 300 K, respectively. (C) 2014 AIP Publishing LLC.

A method of eliminating the surface defect in low-temperature oxidation powder added UO2 pellet

International Nuclear Information System (INIS)

Yoo, H. S.; Lee, S. J.; Kim, J. I.; Jeon, K. R.; Kim, J. W.

2002-01-01

A study on methods to eliminate surface defect shown in low-temperature oxidation powder added UO 2 pellet has been performed. Powders oxidized at 350 .deg. C for 4 hrs were prepared and mixed with UO 2 powder after crushing them. After being sintered, surfaces of the pellet were inspected both visually and optically. A large number of defects were observed on the surface of the specimens in which low-temperature oxidation powders were directly mixed or master mixed with UO 2 powder while both specimens produced from mixed powders including milled oxidation powders and powders that were milled totally after mixing had clean surfaces. However, optical examination showed considerably large defected pores in the milled oxidation powder added pellet and it was confirmed that the inner defects can be eliminated completely only when milling the entire mixture on UO 2 and low-temperature oxidation powder, but not by crushing only oxidation powder

The percolation effect and optimization of soft magnetic properties of FeSiAl magnetic powder cores

Energy Technology Data Exchange (ETDEWEB)

Bai, Ruru [College of Material Science and Engineering, Nanchang University, Nanchang 330031, Jiangxi (China); Zhu, Zhenghou, E-mail: z00708@sina.com [College of Material Science and Engineering, Nanchang University, Nanchang 330031, Jiangxi (China); Zhao, Hui, E-mail: candyzhaohui@126.com [College of Material Science and Engineering, Nanchang University, Nanchang 330031, Jiangxi (China); Institute of Space Science and Technology, Nanchang University, Nanchang 330031, Jiangxi (China); Mao, Shenghua [Jiangxi Aite magnetic materials Co. Ltd., Yichun 336000, Jiangxi (China); Zhong, Qi [College of Material Science and Engineering, Nanchang University, Nanchang 330031, Jiangxi (China)

2017-07-01

Highlights: • A new magnetic percolation phenomenon of ρ-μe in MPCs was discovered. • The soft magnetic properties of FeSiAl MPCs were studied. • The comprehensive magnetic properties of MPCs were optimized. • The formation mechanism of magnetic conductive path was explained. - Abstract: In this paper, a new magnetic percolation phenomenon between the green compact density ρ and effective permeability μe in FeSi{sub 9.6}Al{sub 6.5} magnetic powder cores, was discovered. The Magnetic Percolation Area of ρ is the range of 5.6 g/cm{sup 3} ∼ 5.78 g/cm{sup 3}, and the percolation threshold is 5.78 g/cm{sup 3}. As a result of the guidance of the percolation theory, the best comprehensive magnetic properties have been optimized through adjusting the distribution of powders. The special distribution of the magnetic powder cores with the best comprehensive magnetic properties was as follows: the content 60% with the particle size distribution of 100–200 mesh, the content 20% with the particle size distribution of 200–325 mesh and the content 20% with the particle size distribution of ≥400 mesh. When the green compact density ρ of cores was 5.79 g/cm{sup 3}, and the frequency was in the range of 1 kHz ∼ 100 kHz, the best comprehensive magnetic properties were as follows: μe = 91, ∆μ = 0.61%, μe(H80 Oe) = 43, μe(H100 Oe) = 33, μe(H120 Oe) = 26, Pc(50 mT/20 kHz) = 30.58 kW/m{sup 3}, Pc(50 mT/50 kHz) = 76.85 kW/m{sup 3}, Pc(50 mT/100 kHz) = 178 kW/m{sup 3}. Not only have those cores the excellent constant magnetic properties with frequency, the excellent DC superposition characteristic and the lower loss at high frequency, but also the effective permeability outstandingly goes up, which has important significance for the miniaturization of inductance components.

Anisotropic powder from sintered NdFeB magnets by the HDDR processing route

Energy Technology Data Exchange (ETDEWEB)

Sheridan, R.S.; Sillitoe, R.; Zakotnik, M.; Harris, I.R. [School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Williams, A.J., E-mail: a.j.williams@bham.ac.uk [School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom)

2012-01-15

Sintered NdFeB-based scrap magnets were recovered and processed using the HD and HDDR routes. The effects of varying the HDDR processing temperature were investigated (over the range 835-930 deg. C). The disproportion was carried out with a pressure ramp to a maximum of 1000 mbar hydrogen pressure with a 1 h hold time at each step and the optimum recombination conditions were set at 100 mbar with a 20 min hold time. Anisotropic NdFeB powder was produced in all cases with the best magnetic properties achieved at a processing temperature of 880 deg. C, producing powder with a remanence of 1.10({+-}0.02) T and an intrinsic coercivity of 800 ({+-}16) kA m{sup -1} and giving a (BH){sub max} of 129({+-}2.5) kJ m{sup -3}. - Highlights: > Production of anisotropic permanent magnet powder from scrap NdFeB magnets by HDDR. > Reaction pressure increases with increasing processing temperature. > Best magnetic properties achieved by processing at 880 deg. C.

Anisotropic powder from sintered NdFeB magnets by the HDDR processing route

International Nuclear Information System (INIS)

Sheridan, R.S.; Sillitoe, R.; Zakotnik, M.; Harris, I.R.; Williams, A.J.

2012-01-01

Sintered NdFeB-based scrap magnets were recovered and processed using the HD and HDDR routes. The effects of varying the HDDR processing temperature were investigated (over the range 835-930 deg. C). The disproportion was carried out with a pressure ramp to a maximum of 1000 mbar hydrogen pressure with a 1 h hold time at each step and the optimum recombination conditions were set at 100 mbar with a 20 min hold time. Anisotropic NdFeB powder was produced in all cases with the best magnetic properties achieved at a processing temperature of 880 deg. C, producing powder with a remanence of 1.10(±0.02) T and an intrinsic coercivity of 800 (±16) kA m -1 and giving a (BH) max of 129(±2.5) kJ m -3 . - Highlights: → Production of anisotropic permanent magnet powder from scrap NdFeB magnets by HDDR. → Reaction pressure increases with increasing processing temperature. → Best magnetic properties achieved by processing at 880 deg. C.

Microstructural evolution of ferritic steel powder during mechanical alloying with iron oxide

Energy Technology Data Exchange (ETDEWEB)

Wen, Yuren; Liu, Yong; Liu, Donghua; Tang, Bei [Central South Univ., State Key Lab. of Powder Metallurgy, Changsha (China); Liu, C.T. [The Hong Kong Polytechnic Univ., Dept. of Mechanical Engineering, Hong Kong (China)

2011-02-15

Mechanical alloying of mixed powders is of great importance for preparing oxide dispersion strengthened ferritic steels. In this study, the microstructural evolution of ferritic steel powder mixed with TiH{sub x}, YH{sub 2} and Fe{sub 2}O{sub 3} in the process of mechanical alloying is systematically investigated by using X-ray diffraction analysis, scanning electron microscopy, transmission electron microscopy and microhardness tests. It is found that titanium, yttrium hydrides and iron oxide are completely dissolved during milling, and homogeneous element distribution can be achieved after milling for 12 h. The disintegration of the composite powder particles occurs at 24 h and reaches the balance of welding and fracturing after 36 h. The oxygen content increases sharply with the disintegration of powder particles due to the absorption of oxygen at the solid/gas interface from the milling atmosphere, which is the main source of extra oxygen in the milled powder. Grain refinement down to nanometer level occurs due to the severe plastic deformation of particles; however, the grain size does not change much with further disintegration of particles. The hardness increases with milling time and then becomes stable during further milling. The study indicates that the addition of iron oxide and hydrides may be more beneficial for the dispersion and homogenization of chemical compositions in the powder mixture, thus shortening the mechanical alloying process. (orig.)

Metal-Matrix Hardmetal/Cermet Reinforced Composite Powders for Thermal Spray

Directory of Open Access Journals (Sweden)

Dmitri GOLJANDIN

2012-03-01

Full Text Available Recycling of materials is becoming increasingly important as industry response to public demands, that resources must be preserved and environment protected. To produce materials competitive in cost with primary product, secondary producers have to pursue new technologies and other innovations. For these purposes different recycling technologies for composite materials (oxidation, milling, remelting etc are widely used. The current paper studies hardmetal/cermet powders produced by mechanical milling technology. The following composite materials were studied: Cr3C2-Ni cermets and WC-Co hardmetal. Different disintegrator milling systems for production of powders with determined size and shape were used. Chemical composition of produced powders was analysed.  To estimate the properties of recycled hardmetal/cermet powders, sieving analysis, laser granulometry and angularity study were conducted. To describe the angularity of milled powders, spike parameter–quadric fit (SPQ was used and experiments for determination of SPQ sensitivity and precision to characterize particles angularity were performed. Images used for calculating SPQ were taken by SEM processed with Omnimet Image Analyser 22. The graphs of grindability and angularity were composed. Composite powders based on Fe- and Ni-self-fluxing alloys for thermal spray (plasma and HVOF were produced. Technological properties of powders and properties of thermal sprayed coatings from studied powders were investigated. The properties of spray powders reinforced with recycled hardmetal and cermet particles as alternatives for cost-sensitive applications were demonstrated.DOI: http://dx.doi.org/10.5755/j01.ms.18.1.1348

The influence of powder particle size on properties of Cu-Al2O3 composites

Directory of Open Access Journals (Sweden)

Rajković V.

2009-01-01

Full Text Available Inert gas atomized prealloyed copper powder containing 2 wt.% Al (average particle size ≈ 30 μm and a mixture consisting of copper (average particle sizes ≈ 15 μm and 30 μm and 4 wt.% of commercial Al2O3 powder particles (average particle size ≈ 0.75 μm were milled separately in a high-energy planetary ball mill up to 20 h in air. Milling was performed in order to strengthen the copper matrix by grain size refinement and Al2O3 particles. Milling in air of prealloyed copper powder promoted formation of finely dispersed nano-sized Al2O3 particles by internal oxidation. On the other side, composite powders with commercial micro-sized Al2O3 particles were obtained by mechanical alloying. Following milling, powders were treated in hydrogen at 400 0C for 1h in order to eliminate copper oxides formed on their surface during milling. Hot-pressing (800 0C for 3 h in argon at pressure of 35 MPa was used for compaction of milled powders. Hot-pressed composite compacts processed from 5 and 20 h milled powders were additionally subjected to high temperature exposure (800°C for 1 and 5h in argon in order to examine their thermal stability. The results were discussed in terms of the effects of different size of starting powders, the grain size refinement and different size of Al2O3 particles on strengthening, thermal stability and electrical conductivity of copper-based composites.

Characterization of high-energy milled alumina powders Caracterização de pós de alumina submetidos a moagem de alta energia

Directory of Open Access Journals (Sweden)

Roberto Tomasi

1998-10-01

Full Text Available The utilization of reactive high-energy milling has been reported for the synthesis of ceramic powders namely, metal oxides, carbides, borides, nitrides or mixtures of ceramics or ceramic and metal compounds. In this work, high-energy milling was used for reduction of alumina powders to nanometric particle size. The ceramic characteristics of the powders were analyzed in terms of the behavior during deagglomeration, compaction curves, sintering and microstructure characterization. It was observed that the high energy milling has strong effect in producing agglomeration of the nanosized powders. This effect is explained by the high-energy impact of the balls, which may fracture particles or just cause the particles compacting. In this case, strong agglomerates are produced. As the powder surface area increases, stronger agglomerates are produced.Tem sido amplamente divulgada a utilização da moagem reativa de alta energia para a síntese de pós cerâmicos de óxidos de metais, carbetos, boretos, nitretos ou misturas de compostos cerâmicos ou compostos cerâmicos e metálicos. Neste trabalho, a moagem de alta energia (não reativa foi utilizada para a redução de pós de alumina para partículas de dimensões nanométricas. As características cerâmicas dos pós obtidos foram analisadas a partir de resultados de comportamento durante a desaglomeração, curvas de densificação, sinterização e caracterização de microestrutura. Observou-se que a moagem de alta energia tem forte efeito de aglomeração dos pós com partículas em dimensões nanométricas. Esse efeito é explicado pelo impacto de alta energia das bolas, os quais podem fraturar as partículas ou apenas causar a compactação das mesmas. Nesse último caso, que sempre ocorre, são formados aglomerados de alta resistência. O aumento da área superficial do pó produz aglomerados mais resistentes.

Synthesis and characterization of superconducting YBCO powder

International Nuclear Information System (INIS)

Praveen, B.; Karki, T.; Krishnamoorthi, J.

2008-01-01

Full text: Superconducting yttrium barium copper oxide power has been synthesized through solid state sintering method - milling and sintering - using Y 2 O 3 , BaCo 3 and CuO powders. XRD result of the milled and sintered powder reveals that the powder that has formed contains YBa 2 Cu 3 O 6.5 superconducting phase. Results obtained by SEM/EDAX show the distribution of the different elements. Experiments carried out by intermediate firing and final annealing in oxygen controlled atmosphere show the diffusion of oxygen in preformed YBa 2 Cu 3 O 6.5 and their results are discussed

The influence of the milling environment on the sintered structure of a W-Cu composite

International Nuclear Information System (INIS)

Costa, F.A.; Gomes, U.U.; Acchar, W.; Ambrozio Filho, F.; Silva, A.G.P.; Lima, S.J.G.

2009-01-01

This work reports an investigation about the influence of the environment of milling on the characteristics of the powders and on the structure and density of sintered samples made of these powders. Mixtures of composition W-30wt%Cu were milled for 51 hours in a high energy planetary mill in dry and wet (cyclohexane) conditions. The milled powders have composite particles. The powders were pressed and sintered at 1050 deg, 1150 deg and 1200 deg C under flowing hydrogen. The isothermal times were 0 minutes for the first two temperatures and 60 minutes for the latter. The samples reached around 95% of relative density. The powders were characterized by means of XRD and SEM. The sintered samples were characterized by means of SEM, optical microscopy and density measurement. (author)

A study of the mechanism of microwave-assisted ball milling preparing ZnFe{sub 2}O{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yingzhe; Wu, Yujiao [College of materials and metallurgical engineering, Guizhou Institute of Technology, Guiyang 550003 (China); 2011 Collaborative Innovation Center of Guizhou Province, Guiyang 550003 (China); Qin, Qingdong [College of materials and metallurgical engineering, Guizhou Institute of Technology, Guiyang 550003 (China); Wang, Fuchun [College of materials and metallurgical engineering, Guizhou Institute of Technology, Guiyang 550003 (China); 2011 Collaborative Innovation Center of Guizhou Province, Guiyang 550003 (China); Chen, Ding [College of Materials Science and Engineering, Hunan University, Changsha, Hunan 410082 (China)

2016-07-01

In this paper, well dispersed ZnFe{sub 2}O{sub 4} nano-particles with high magnetization saturation of 82.23 emu/g were first synthesized by microwave assisted ball milling and then the influences of pre-treatments and microwave powers to the progress were studied. It was found that under the both function of crack effect induced by ball milling and rotary motion induced by microwave the synthesized ferrtie nano-particles were well dispersed that is much different from the powders synthesized by normal high energy ball milling. The pre-treatment of ball milling can only enhance the reaction rate in the first several hours but the pre-irradiation of microwave can enhance the hole reaction rate. Further more, it was also been found that with increasing the microwave power, the more raw materials will converted into zinc ferrite in the first 5 h. 5 h latter the microwave power of 720 W is high enough for the coupling effect of microwave and ball milling with stirrer rotation speed of 256 rpm. - Highlights: • ZnFe{sub 2}O{sub 4} with 82.23 emu/g were synthesized without heat treatment. • The produced powder dispersed very well without any dispersant. • The pre-treatment of microwave enhanced the reaction rate much. • The pre-treatment of ball milling enhance chemical rate at beginning.

Crystalline-to-amorphous phase transformation in mechanically alloyed Fe50W50 powders

International Nuclear Information System (INIS)

Sherif El-Eskandarany, M.S.; Sumiyama, K.; Suzuki, K.

1997-01-01

A mechanical alloying process via a ball milling technique has been applied for preparing amorphous Fe 50 W 50 alloy powders. The results have shown that during the first and second stages of milling (0 to 360 ks) W atoms emigrate to Fe lattices to form nanocrystalline b.c.c. Fe-W solid solution, with a grain size of about 7 nm in diameter. After 720 ks of the milling time, this solid solution was transformed to an amorphous Fe-W alloy coexisting with the residual fraction of the unprocessed W powders. During the last stage of milling (720 to 1,440 ks) all of this residual W powder reacts with the amorphous phase to form a homogeneous Fe 50 W 50 amorphous alloy. The crystallization temperature and the enthalpy change of crystallization of amorphous Fe 50 W 50 powders milled for 1,440 ks were measured to be 860 K and -9kJ/mol, respectively. The amorphous Fe 50 W 50 powder produced is almost paramagnetic at room temperature. The powder comprises homogeneous and smooth spheres with an average size of about 0.5 microm in diameter

Soft x-ray resonant magnetic powder diffraction on PrNiO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Staub, U [Swiss Light Source, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); GarcIa-Fernandez, M [Swiss Light Source, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Mulders, A M [Department of Applied Physics, Curtin University of Technology, GPO Box U1987, Perth WA 6845 (Australia); Bodenthin, Y [Swiss Light Source, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); MartInez-Lope, M J [Instituto de Ciencia de Materiales de Madrid, CSIC, Cantoblanco, E-28049 Madrid (Spain); Alonso, J A [Instituto de Ciencia de Materiales de Madrid, CSIC, Cantoblanco, E-28049 Madrid (Spain)

2007-03-07

We report on the first soft x-ray resonant powder diffraction experiments performed at the Ni L{sub 2,3} edges of PrNiO{sub 3}. The temperature, polarization and energy dependence of the (1/2 0 1/2) reflection indicates a magnetic origin for the signal. This experiment demonstrates that x-ray resonant magnetic powder diffraction can be relatively easily performed in the soft x-ray regime due to the very large enhancement factors at the absorption edges. Such experiments allow us to extract important information on the electronic states of the d shell. Similar results can be anticipated from orbital reflections measured in a powder. (fast track communication)

Comparative Study by MS and XRD of Fe50Al50 Alloys Produced by Mechanical Alloying, Using Different Ball Mills

International Nuclear Information System (INIS)

Rojas Martinez, Y.; Perez Alcazar, G. A.; Bustos Rodriguez, H.; Oyola Lozano, D.

2005-01-01

In this work we report a comparative study of the magnetic and structural properties of Fe 50 Al 50 alloys produced by mechanical alloying using two different planetary ball mills with the same ball mass to powder mass relation. The Fe 50 Al 50 sample milled during 48 h using the Fritsch planetary ball mill pulverisette 5 and balls of 20 mm, presents only a bcc alloy phase with a majority of paramagnetic sites, whereas that sample milled during the same time using the Fritsch planetary ball mill pulverisette 7 with balls of 15 mm, presents a bcc alloy phase with paramagnetic site (doublet) and a majority of ferromagnetic sites which include pure Fe. However for 72 h of milling this sample presents a bcc paramagnetic phase, very similar to that prepared with the first system during 48 h. These results show that the conditions used in the first ball mill equipment make more efficient the milling process.

ZnO nanoparticles obtained by ball milling technique: Structural, micro-structure, optical and photo-catalytic properties

Energy Technology Data Exchange (ETDEWEB)

Balamurugan, S., E-mail: scandium.chemistry@gmail.com; Joy, Josny; Godwin, M. Anto; Selvamani, S.; Raja, T. S. Gokul [Advanced Nanomaterials Research Laboratory, Department of Nanotechnology, Noorul Islam Centre for Higher Education, Thuckalay, Kumaracoil - 629 180 (India)

2016-05-23

The ZnO nanoparticles were obtained by ball milling of commercial grade ZnO powder at 250 rpm for 20 h and studied their structural, micro-structure, optical and photo-catalytic properties. Due to ball milling significant decrease in lattice parameters and average crystalline size is noticed for the as-milled ZnO nano powder. The HRSEM images of the as-milled powder consist of agglomerated fine spherical nanoparticles in the range of ~10-20 nm. The room temperature PL spectrum of as-milled ZnO nano powder excited under 320 nm reveals two emission bands at ~406 nm (violet emission) and ~639 nm (green emission). Interestingly about 98 % of photo degradation of methylene (MB) by the ZnO catalyst is achieved at 100 minutes of solar light irradiation.

Magnetic properties of co-precipitated hexaferrite powders with Sm-Co substitutions optimized with the molten flux method

Science.gov (United States)

Serletis, C.; Litsardakis, G.; Pavlidou, E.; Efthimiadis, K. G.

2017-11-01

In this work, using the chemical coprecipitation method, Sr1-xSmxFe12-xCoxO19 (x = 0, 0.1, 0.2) hexaferrite powders were prepared. Major magnetization loops were recorded at room temperature in order to determine the correct calcination temperature for optimum hard magnetic properties. It is found that a small degree of substitution increases substantially the coercive field. Also, the use of the molten flux calcination method increases the remanent magnetization. SEM/EDXS and XRD measurements were performed at the calcined powders: the results show that a single hexaferrite phase is formed and that the substituted powders consist of an assembly of grains with a mean diameter of 40 nm. Measurements of minor magnetization loops and of the temperature and time dependence of the magnetization confirm that the powders consist of a non-oriented single domain magnetic particles assembly. The results indicate that Sm could be a viable replacement for La in the manufacturing of hexaferrites with a high-energy product.

Structural and magnetic evolution of nanostructured Co{sub 40}Fe{sub 10}Zr{sub 10}B{sub 40} prepared by mechanical alloying

Energy Technology Data Exchange (ETDEWEB)

Raanaei, Hossein, E-mail: hraanaei@yahoo.com [Department of Physics, Persian Gulf University, Bushehr 75169 (Iran, Islamic Republic of); Abbasi, Sadeq [Department of Physics, Persian Gulf University, Bushehr 75169 (Iran, Islamic Republic of); Behaein, Saeed [Department of Physics, Shiraz University, Shiraz 71454 (Iran, Islamic Republic of)

2015-06-15

The structural and magnetic properties of nanocrystalline alloy powder Co{sub 40}Fe{sub 10}Zr{sub 10}B{sub 40} prepared by mechanical alloying have been characterized by using X-ray diffraction (XRD), scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and differential scanning calorimeter (DSC). It is shown that the crystallite size has been decreased significantly to about 15 nm after 8 h milling time. On continuing the milling time mechanical crystallization and subsequently the alloying process were noticed up to 190 h. Saturation magnetization decreased during the whole process while coercivity achieved the highest value at the crystallization stage. Post treatment of milled powder at 190 h revealed crystalline constituent elements. - Highlights: • This article focuses on mechanical alloying of Co{sub 40}Fe{sub 10}Zr{sub 10}B{sub 40} system. • Mechanical crystallization is observed. • Structural and magnetic properties were investigated. • The heat treatment revealed the crystalline phases of constituent elements.

Study on the RF inductively coupled plasma spheroidization of refractory W and W-Ta alloy powders

Science.gov (United States)

Chenfan, YU; Xin, ZHOU; Dianzheng, WANG; Neuyen VAN, LINH; Wei, LIU

2018-01-01

Spherical powders with good flowability and high stacking density are mandatory for powder bed additive manufacturing. Nevertheless, the preparation of spherical refractory tungsten and tungsten alloy powders is a formidable task. In this paper, spherical refractory metal powders processed by high-energy stir ball milling and RF inductively coupled plasma were investigated. By utilizing the technical route, pure spherical tungsten powders were prepared successfully, the flowability increased from 10.7 s/50 g to 5.5 s/50 g and apparent density increased from 6.916 g cm-3 to 11.041 g cm-3. Alloying element tantalum can reduce the tendency to micro-crack during tungsten laser melting and rapid solidification process. Spherical W-6Ta (%wt) powders were prepared in this way, homogeneous dispersion of tantalum in a tungsten matrix occurred but a small amount of flake-like shape particles appeared after high-energy stir ball milling. The flake-like shape particles can hardly be spheroidized in subsequent RF inductively coupled plasma process, might result from the unique suspended state of flaky particles under complex electric and magnetic fields as well as plasma-particle heat exchange was different under various turbulence models. As a result, the flake-like shape particles cannot pass through the high-temperature area of thermal plasma torch and cannot be spheroidized properly.

Advances in Powder Metallurgy Soft Magnetic Composite Materials

Directory of Open Access Journals (Sweden)

Bureš R.

2017-06-01

Full Text Available Powder metallurgy has grown with the expansion of various industry. Automotive industry had the most strong influence. Today, more than 90% of PM products are used in the transportation industry. Development of new materials such as magnetic materials is expected to meet the new trends of automotive industry, electric and hybrid vehicles.

Thermal aging of melt-spun NdFeB magnetic powder in hydrogen

International Nuclear Information System (INIS)

Pinkerton, Frederick E.; Balogh, Michael P.; Ellison, Nicole; Foto, Aldo; Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P.

2016-01-01

High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity H ci of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H 2 gas. Expansion of the NdFeB crystal lattice in both ATF and H 2 identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets. - Highlights: • Injection molded NdFeB magnets age rapidly in automatic transmission fluid (ATF). • Coercivity loss is not due to direct chemical reaction between ATF and the powder. • Chemical reaction with the binder does not play a major role in aging. • Hydrogen dissociates from ATF and diffuses into Nd 2 Fe 14 B, reducing coercivity.

Thermal aging of melt-spun NdFeB magnetic powder in hydrogen

Energy Technology Data Exchange (ETDEWEB)

Pinkerton, Frederick E., E-mail: frederick.e.pinkerton@gm.com [Chemical and Materials Systems Laboratory, General Motors Research and Development Center, Warren, MI 48092 (United States); Balogh, Michael P.; Ellison, Nicole [Chemical and Materials Systems Laboratory, General Motors Research and Development Center, Warren, MI 48092 (United States); Foto, Aldo [Element Materials Technology Wixom, Inc (United States); Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P. [Powertrain Materials/Fluids/AMPPD Engineering and Labs, GFL VE/PT Materials Engineering, General Motors LLC, Pontiac, MI 48340 (United States)

2016-11-01

High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity H{sub ci} of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H{sub 2} gas. Expansion of the NdFeB crystal lattice in both ATF and H{sub 2} identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets. - Highlights: • Injection molded NdFeB magnets age rapidly in automatic transmission fluid (ATF). • Coercivity loss is not due to direct chemical reaction between ATF and the powder. • Chemical reaction with the binder does not play a major role in aging. • Hydrogen dissociates from ATF and diffuses into Nd{sub 2}Fe{sub 14}B, reducing coercivity.

Discrete element method based scale-up model for material synthesis using ball milling

Science.gov (United States)

Santhanam, Priya Radhi

Mechanical milling is a widely used technique for powder processing in various areas. In this work, a scale-up model for describing this ball milling process is developed. The thesis is a combination of experimental and modeling efforts. Initially, Discrete Element Model (DEM) is used to describe energy transfer from milling tools to the milled powder for shaker, planetary, and attritor mills. The rolling and static friction coefficients are determined experimentally. Computations predict a quasisteady rate of energy dissipation, E d, for each experimental configuration. It is proposed that the milling dose defined as a product of Ed and milling time, t, divided by the mass of milled powder, mp characterizes the milling progress independently of the milling device or milling conditions used. Once the milling dose is determined for one experimental configuration, it can be used to predict the milling time required to prepare the same material in any milling configuration, for which Ed is calculated. The concept is validated experimentally for DEM describing planetary and shaker mills. For attritor, the predicted Ed includes substantial contribution from milling tool interaction events with abnormally high forces (>103 N). The energy in such events is likely dissipated to heat or plastically deform milling tools rather than refine material. Indeed, DEM predictions for the attritor correlate with experiments when such events are ignored in the analysis. With an objective of obtaining real-time indicators of milling progress, power, torque, and rotation speed of the impeller of an attritor mill are measured during preparation of metal matrix composite powders in the subsequent portion of this thesis. Two material systems are selected and comparisons made between in-situ parameters and experimental milling progress indicators. It is established that real-time measurements can certainly be used to describe milling progress. However, they need to be interpreted carefully

Magnetic properties of La0.7Ca0.3MnO3 nanoparticles prepared by reactive milling

International Nuclear Information System (INIS)

Do Hung Manh; Nguyen Chi Thuan; Pham Thanh Phong; Le Van Hong; Nguyen Xuan Phuc

2009-01-01

La 0.7 Ca 0.3 MnO 3 (LCMO) nanoparticles were synthesized by reactive milling in ambient conditions. Magnetic properties of LCMO single-phase nanocrystalline particles were studied. LCMO nanoparticles exhibit superparamagnetism with blocking temperature that decreases in the logarithmic function as increasing applied magnetic field. Besides, the blocking temperature decreases as increasing milling time from 8 h to 16 h. The temperature dependence of the saturation magnetization shows a strong collective excitation due to the spin wave that depends on temperature in form T α with α = 1.7, which slightly deviates from the Bloch law.

Superfine powdered activated carbon (S-PAC) coatings on microfiltration membranes: Effects of milling time on contaminant removal and flux.

Science.gov (United States)

Amaral, Pauline; Partlan, Erin; Li, Mengfei; Lapolli, Flavio; Mefford, O Thompson; Karanfil, Tanju; Ladner, David A

2016-09-01

In microfiltration processes for drinking water treatment, one method of removing trace contaminants is to add powdered activated carbon (PAC). Recently, a version of PAC called superfine PAC (S-PAC) has been under development. S-PAC has a smaller particle size and thus faster adsorption kinetics than conventionally sized PAC. Membrane coating performance of various S-PAC samples was evaluated by measuring adsorption of atrazine, a model micropollutant. S-PACs were created in-house from PACs of three different materials: coal, wood, and coconut shell. Milling time was varied to produce S-PACs pulverized with different amounts of energy. These had different particles sizes, but other properties (e.g. oxygen content), also differed. In pure water the coal based S-PACs showed superior atrazine adsorption; all milled carbons had over 90% removal while the PAC had only 45% removal. With addition of calcium and/or NOM, removal rates decreased, but milled carbons still removed more atrazine than PAC. Oxygen content and specific external surface area (both of which increased with longer milling times) were the most significant predictors of atrazine removal. S-PAC coatings resulted in loss of filtration flux compared to an uncoated membrane and smaller particles caused more flux decline than larger particles; however, the data suggest that NOM fouling is still more of a concern than S-PAC fouling. The addition of calcium improved the flux, especially for the longer-milled carbons. Overall the data show that when milling S-PAC with different levels of energy there is a tradeoff: smaller particles adsorb contaminants better, but cause greater flux decline. Fortunately, an acceptable balance may be possible; for example, in these experiments the coal-based S-PAC after 30 min of milling achieved a fairly high atrazine removal (overall 80%) with a fairly low flux reduction (under 30%) even in the presence of NOM. This suggests that relatively short duration (low energy

Physical characteristics and magnetic properties of BaFe12O19/SrTiO3 based composites derived from mechanical alloying

International Nuclear Information System (INIS)

Widodo, Rahmat Doni; Manaf, Azwar

2016-01-01

A composite system BaFe 12 O 19 /SrTiO 3 with ferrimagnetic BaFe 12 O 19 phase (BHF) and ferroelectric SrTiO 3 phase (STO) have been prepared by mechanical alloying and subsequent heat treatment. The composite powders were studied by Particle Size Analyze, X-ray diffraction and magnetic measurement. It was found that the particle size of composite powders initially increased due to laminated layers formation of a composite and then decreased to an asymptotic value of ∼8 µm as the milling time extended even to a relatively longer time. However, based on results of line broadening analysis the mean grain size of the particles was found in the nanometer scale. We thus believed that mechanical blending and milling of mixture components for the composite materials has promoted heterogeneous nucleation and only after successive sintering at 1100°C the milled powder transformed into particles of nanograin. In this report, microstructure as well as magnetic properties for the composite is also briefly discussed.

Investigation of the oxidative processes in intermetallic Sm Co5 powder during heat treatment

International Nuclear Information System (INIS)

Talijan, Nadezda M.; Milutinovic-Nikolic, Aleksandra; Stajic-Trosic, Jasna T.; Jovanovic, Zarko D.

1996-01-01

Understanding of the thermal stability of intermetallic Sm Co 5 powder is essential for designing the working atmosphere in all phases of the technological procedure in the production of sintered Sm Co 5 magnets to obtain maximal magnetic properties. The thermal stability of the Sm Co 5 powder with defined chemical composition and particle size was investigated in the interval from 20 to 900 deg C. Commercial Sm Co 5 powder was used in this experiment. The powder was milled in anhydrous toluene in an agate mortar to fine powder of quality used in the production of sintered magnets. All the experiments were carried out with powder of an average particle size of 7.23μm, established by SEM. THe thermal stability of the Sm Co 5 powder in static air atmosphere was investigated by thermogravimetric analysis (TGA) using a DuPont Thermal Analyzer. Investigation of the behaviour of Sm Co 5 powder during heating was carried out using new samples of Sm Co 5 powder for each of the investigated temperature cycles. It was found by TGA that up to 200 deg C, the oxidation of Sm Co 5 was negligible. X-ray diffraction of the thermogravimetric experimental residue of the Sm Co 5 powder, heated at 240 deg C, yielded only the presence of the Sm Co 5 phase. By X-ray diffraction different crystal forms were identified depending on the maximal heating temperature. The following phases were identified: Sm 2 O 3 , Co, Co O, Co 3 O 4 and Sm Co O 3 . According to TG and X-ray results, for each of the investigated temperatures, the corresponding chemical reactions were established. The experimental data from both the thermal and X-ray investigations confirm that the phases of pressing and aligning the Sm Co 5 powder, in the process of producing sintered Sm Co 5 magnets, may be performed without a protective atmosphere. (author)

Low-temperature synthesis of MgB{sub 2} via powder metallurgy processing

Energy Technology Data Exchange (ETDEWEB)

Birol, Yucel [Dokuz Eylul University, Department of Metallurgical and Materials Engineering, Faculty of Engineering, Buca, Izmir (Turkey)

2016-12-15

Ball-milled Mg/B{sub 2}O{sub 3} powder blends reveal interpenetrating layers of deformed magnesium and boron oxide grains that are increasingly refined with increasing milling time. Boron oxide is reduced by Mg and MgO thus formed reacts with the remaining B{sub 2}O{sub 3} to produce Mg{sub 3}(BO{sub 3}){sub 2} during ball milling for 30 min. Both B{sub 2}O{sub 3} and Mg{sub 3}(BO{sub 3}){sub 2} react with Mg to produce MgB{sub 2} upon further ball milling. An annealing treatment can be employed when ball milling is performed for less than 1 h as thermal exposure of the ball-milled Mg/B{sub 2}O{sub 3} powder blends also leads to the formation of MgB{sub 2}. The above reactions take place between 500 and 700 C when the Mg/B{sub 2}O{sub 3} powder blend is ball milled for 30 min, and between 450 and 550 C, after ball milling for 1 h. This is a very attractive route owing to processing temperatures where the volatility of Mg is no longer a problem. (orig.)

Comparative Study by MS and XRD of Fe{sub 50}Al{sub 50} Alloys Produced by Mechanical Alloying, Using Different Ball Mills

Energy Technology Data Exchange (ETDEWEB)

Rojas Martinez, Y., E-mail: yarojas@ut.edu.co [University of Tolima, Department of Physics (Colombia); Perez Alcazar, G. A. [University of Valle, Department of Physics (Colombia); Bustos Rodriguez, H.; Oyola Lozano, D., E-mail: doyolalozano@yahoo.com.mx [University of Tolima, Department of Physics (Colombia)

2005-02-15

In this work we report a comparative study of the magnetic and structural properties of Fe{sub 50}Al{sub 50} alloys produced by mechanical alloying using two different planetary ball mills with the same ball mass to powder mass relation. The Fe{sub 50}Al{sub 50} sample milled during 48 h using the Fritsch planetary ball mill pulverisette 5 and balls of 20 mm, presents only a bcc alloy phase with a majority of paramagnetic sites, whereas that sample milled during the same time using the Fritsch planetary ball mill pulverisette 7 with balls of 15 mm, presents a bcc alloy phase with paramagnetic site (doublet) and a majority of ferromagnetic sites which include pure Fe. However for 72 h of milling this sample presents a bcc paramagnetic phase, very similar to that prepared with the first system during 48 h. These results show that the conditions used in the first ball mill equipment make more efficient the milling process.

Synthesis of Ni-YSZ cermet for an electrode of high temperature electrolysis by high energy ball milling

International Nuclear Information System (INIS)

Hong, H.S.; Chae, U.S.; Park, K.M.; Choo, S.T.

2005-01-01

Ni/YSZ composites for a cathode that can be used in high temperature electrolysis were prepared by ball milling of Ni and YSZ powder. Ball milling was performed in a dry process and in ethanol. The microstructure and electrical conductivity of the composites were examined by XRD, SEM, TEM and a 4-point probe. XRD patterns for both the dry and wet ball-milled powders showed that the composites were composed of crystalline Ni and YSZ particles. The patterns did not change with increases in the milling time up to 48 h. Dry-milling slightly increased the average particle size compared to starting Ni particles, but little change in the particle size was observed with the increase in milling time. On the other hand, the wet-milling reduced the average size and the increasing milling time induced a further decrease in the particle size. After cold-pressing and annealing at 900 C for 2 h, the dry-milled powder exhibited high stability against Ni sintering so that the particle size changed little, but the particle size increased in the wet-milled powder. The electrical conductivity increased after sintering at 900 C. Particles from the dry and wet process became denser and contacted closer after sintering, providing better electron migration paths. (orig.)

A novel use of Moringa oleifera seed powder in enhancing the primary treatment of paper mill effluent.

Science.gov (United States)

Boulaadjoul, Soumia; Zemmouri, Hassiba; Bendjama, Zoubida; Drouiche, Nadjib

2018-05-02

In this study, Moringa oleifera (M. oleifera) performance as an eco-friendly coagulant in the enhanced primary treatment of paper mill effluent was investigated. Its performance in terms of turbidity removal and COD abatement was examined. Local M. oleifera seed powder from ADRAR-city, South of Algeria, was used. Conventional jar tests were conducted for enhancing the primary treatment of paper mill effluent from paper factory. For this reason, comparative coagulation tests were performed using aluminum sulfate (alum). Indeed, in terms of turbidity abatement, 96.02% and 97.1% were obtained for Moringa and alum, respectively. However, in the case of COD abatement, the abatement rate of M. oleifera seeds was slightly higher than that of alum, 97.28% and 92.67%, respectively. Because M. oleifera is a natural resource that is locally available, an eco-friendly coagulant, non-toxic, and biodegradable and does not affect the pH of water; thus, its use allows to avoid numerous disadvantages of conventional coagulants like alum. Copyright © 2018 Elsevier Ltd. All rights reserved.

Powder-in-Tube (PIT) Nb3Sn conductors for high-field magnets

NARCIS (Netherlands)

Lindenhovius, J.H.; Hornsveld, E.M.; den Ouden, A.; Wessel, Wilhelm A.J.; ten Kate, Herman H.J.

2000-01-01

New Nb3Sn conductors, based on the powder-in-tube (PIT) process, have been developed for application in accelerator magnets and high-field solenoids. For application in accelerator magnets, SMI has developed a binary 504 filament PIT conductor by optimizing the manufacturing process and adjustment

Thermal aging of melt-spun NdFeB magnetic powder in hydrogen

Science.gov (United States)

Pinkerton, Frederick E.; Balogh, Michael P.; Ellison, Nicole; Foto, Aldo; Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P.

2016-11-01

High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity Hci of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H2 gas. Expansion of the NdFeB crystal lattice in both ATF and H2 identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets.

PROCESSING OF SOFT MAGNETIC MATERIALS BY POWDER METALLURGY AND ANALYSIS OF THEIR PERFORMANCE IN ELECTRICAL MACHINES

Directory of Open Access Journals (Sweden)

W. H. D. Luna

2017-12-01

Full Text Available This article presents the use of finite elements to analyze the yield of electric machines based on the use of different soft magnetic materials for the rotor and the stator, in order to verify the performance in electric machine using powder metallurgy. Traditionally, the cores of electric machines are built from rolled steel plates, thus the cores developed in this work are obtained from an alternative process known as powder metallurgy, where powders of soft magnetic materials are compacted and sintered. The properties of interest were analyzed (magnetic, electric and mechanical properties and they were introduced into the software database. The topology of the rotor used was 400 W three-phase synchronous motor manufactured by WEG Motors. The results show the feasibility to replace the metal sheets of the electric machines by solid blocks obtained by powder metallurgy process with only 0.37% yield losses. In addition, the powder metallurgical process reduces the use of raw materials and energy consumption per kg of raw material processed.

Properties of nanoparticles prepared from NdFeB-based compound for magnetic hyperthermia application.

Science.gov (United States)

Périgo, E A; Silva, S C; de Sousa, E M B; Freitas, A A; Cohen, R; Nagamine, L C C M; Takiishi, H; Landgraf, F J G

2012-05-04

Nanoparticles were prepared from a NdFeB-based alloy using the hydrogen decrepitation process together with high-energy ball milling and tested as heating agent for magnetic hyperthermia. In the milling time range evaluated (up to 10 h), the magnetic moment per mass at H = 1.59 MA m(-1) is superior than 70 A m(2) kg(-1); however, the intrinsic coercivity might be inferior than 20 kA m(-1). The material presents both ferromagnetic and superparamagnetic particles constituted by a mixture of phases due to the incomplete disproportionation reaction of Nd(2)Fe(14)BH(x) during milling. Solutions prepared with deionized water and magnetic particles exposed to an AC magnetic field (H(max) ~ 3.7 kA m(-1) and f = 228 kHz) exhibited 26 K ≤ ΔT(max) ≤ 44 K with a maximum estimated specific absorption rate (SAR) of 225 W kg(-1). For the pure magnetic material milled for the longest period of time (10 h), the SAR was estimated as ~2500 W kg(-1). In vitro tests indicated that the powders have acceptable cytotoxicity over a wide range of concentration (0.1-100 µg ml(-1)) due to the coating applied during milling.

Some Properties of Carbon Fiber Reinforced Magnetic Reactive Powder Concrete Containing Nano Silica

Directory of Open Access Journals (Sweden)

Zain El-Abdin Raouf

2016-08-01

Full Text Available This study involves the design of 24 mixtures of fiber reinforced magnetic reactive powder concrete containing nano silica. Tap water was used for 12 of these mixtures, while magnetic water was used for the others. The nano silica (NS with ratios (1, 1.5, 2, 2.5 and 3 % by weight of cement, were used for all the mixtures. The results have shown that the mixture containing 2.5% NS gives the highest compressive strength at age 7 days. Many different other tests were carried out, the results have shown that the carbon fiber reinforced magnetic reactive powder concrete containing 2.5% NS (CFRMRPCCNS had higher compressive strength, modulus of rupture, splitting tension, stress in compression and strain in compression than the corresponding values for the carbon fiber reinforced nonmagnetic reactive powder concrete containing the same ratio of NS (CFRNRPCCNS. The percentage increase in these values for CFRMRPCCNS were (22.37, 17.96, 19.44, 6.44 and 25.8 % at 28 days respectively, as compared with the corresponding CFRNRPCCNS mixtures.

New developments in NdFeB-based permanent magnets

International Nuclear Information System (INIS)

Liu, Z.W.

2011-01-01

NdFeB based alloys have been used as permanent magnets for almost thirty years. The recent researches aim at optimizing the composition, microstructure and properties, reducing cost, and developing new processes. The demand for sintered magnet is increasing. Efforts are directed towards improving properties by controlling grain boundary diffusion, minimizing the rare earth (RE) content and also improving production yield. As for bonded magnets, to enhance remanence and energy product, nanocrystalline powders are employed. High thermal stability has been realized by mixing NdFeB with hard ferrite powders. For nanocrystalline and nano composite NdFeB based alloys, both compositional modification and microstructural optimization have been carried out. New approaches have also been proposed to prepare NdFeB magnets with idea structure. Surfactant assisted ball milling is a good top-down method to obtain nano sized hard magnetic particles and anisotropic nano flakes. Synthesis of NdFeB nanoparticles and NdFeB/Fe (Co) nano composite powders by bottom-up techniques, such as chemical reduction process and co-precipitation, has been successful very recently. To assemble nanocrystalline NdFeB powders or nanoparticles into bulk magnets, various novel consolidation processes including spark plasma sintering and high velocity press have been employed. Hot deformation can be selected as the process to achieve anisotropy in nanocrystalline magnets. (author)

Characteristics of Cu–Al2O3 composites of various starting particle size obtained by high-energy milling

Directory of Open Access Journals (Sweden)

VIŠESLAVA RAJKOVIĆ

2009-05-01

Full Text Available The powder Cu– Al2O3 composites were produced by high-energy milling. Various combinations of particle size and mixtures and approximately constant amount of Al2O3 were used as the starting materials. These powders were separately milled in air for up to 20 h in a planetary ball mill. The copper matrix was reinforced by internal oxidation and mechanical alloying. During the milling, internal oxidation of pre-alloyed Cu-2 mass %-Al powder generated 3.7 mass % Al2O3 nano-sized particles finely dispersed in the copper matrix. The effect of different size of the starting copper and Al2O3 powder particles on the lattice parameter, lattice distortion and grain size, as well as on the size, morphology and microstructure of the Cu– Al2O3 composite powder particles was studied.

Magnetization and 13C NMR spin-lattice relaxation of nanodiamond powder

Energy Technology Data Exchange (ETDEWEB)

Levin, E.M.; Fang, X.W.; Bud' ko, S.L.; Straszheim, W.E.; McCallum, R.W.; Schmidt-Rohr, K.

2008-02-15

The bulk magnetization at temperatures of 1.8-400 K and in magnetic fields up to 70 kOe, the ambient temperature {sup 13}C NMR spin-lattice relaxation, T{sub 1,c}, and the elemental composition of three nanodiamond powder samples have been studied. The total magnetization of nanodiamond can be explained in terms of contributions from (1) the diamagnetic effect of carbon, (2) the paramagnetic effect of unpaired electrons present in nanodiamond grains, and (3) ferromagnetic-like and (4) superparamagnetic contributions from Fe-containing particles detected in spatially resolved energy-dispersive spectroscopy. Contributions (1) and (2) are intrinsic to nanodiamond, while contributions (3) and (4) arise from impurities naturally present in detonation nanodiamond samples. {sup 13}C NMR T{sub 1,c} relaxation would be unaffected by the presence of the ferromagnetic particles with the bulk magnetization of {approx} 0.01 emu/g at 300 K. Thus, a reduction of T{sub 1,c} by 3 orders of magnitude compared to natural and synthetic microdiamonds confirms the presence of unpaired electrons in the nanodiamond grains. The spin concentration in nanodiamond powder corresponds to {approx}30 unpaired electrons per {approx}4.6 nm diameter nanodiamond grain.

Synthesis and Characterization of Nanocrystalline Al-20 at. % Cu Powders Produced by Mechanical Alloying

Directory of Open Access Journals (Sweden)

Molka Ben Makhlouf

2016-06-01

Full Text Available Mechanical alloying is a powder processing technique used to process materials farther from equilibrium state. This technique is mainly used to process difficult-to-alloy materials in which the solid solubility is limited and to process materials where nonequilibrium phases cannot be produced at room temperature through conventional processing techniques. This work deals with the microstructural properties of the Al-20 at. % Cu alloy prepared by high-energy ball milling of elemental aluminum and copper powders. The ball milling of powders was carried out in a planetary mill in order to obtain a nanostructured Al-20 at. % Cu alloy. The obtained powders were characterized using scanning electron microscopy (SEM, differential scanning calorimetry (DSC and X-ray diffraction (XRD. The structural modifications at different stages of the ball milling are investigated with X-ray diffraction. Several microstructure parameters such as the crystallite sizes, microstrains and lattice parameters are determined.

Obtainment of the alloy Cu13Al4Ni using processed by powder metallurgy

International Nuclear Information System (INIS)

Grossi, L.J.; Damasceno, N.; Muterlle, P.V.

2016-01-01

The powder metallurgy is a technique environmentally advantageous that allows the production of many pieces, with a good superficial finishing and dimensional tolerance. For the production of pieces using technique, basics steps are carried out, as the characterization of powders, the mixing and homogenization, compacting and sintering. In this context, this work has as objective the obtainment of the Cu13Al4Ni alloy via powder metallurgy. For this, was made a high energy milling for 2, 4 and 8 hours. Then, the milled powder was compacted and posteriorly, sintered in an oven with controlled atmosphere. It was observed that the milling time affects directly in sintering of the pieces. The best results obtained were for the samples that were milled for 4 hours. This samples have showed 21, 52% of porosity and 6,382 g/cm³ of the density of sintered. (author)

A simple magnetic balance technique for determining transition temperatures of high T/sub c/ superconducting powders

International Nuclear Information System (INIS)

Takamori, T.; Dove, D.B.

1988-01-01

A simple arrangement is described that provides a convenient method for determining transition behavior of high Tc superconductors that are in powder form. A single-pan balance was modified so that its deviation from balance could be measured by an inductive displacement transducer. A small magnet was attached to the balance and placed in close proximity above the sample to be measured. As the sample is cooled through the transition, magnetic flux lines are locally excluded resulting in a repulsive force on the magnet attached to the balance. The resulting deflection of the balance has sufficient sensitivity to allow measurements on several mg of powder. This technique provides a convenient method for routine surveying of powder samples during materials development. Example measurements are described

Fabrication of NdFeB microstructures using a silicon molding technique for NdFeB/Ta multilayered films and NdFeB magnetic powder

International Nuclear Information System (INIS)

Jiang Yonggang; Fujita, Takayuki; Uehara, Minoru; Iga, Yuki; Hashimoto, Taichi; Hao, Xiuchun; Higuchi, Kohei; Maenaka, Kazusuke

2011-01-01

The silicon molding technique is described for patterning of NdFeB/Ta multilayered magnetic films and NdFeB magnetic powder at the micron scale. Silicon trenches are seamlessly filled by 12-μm-thick NdFeB/Ta multilayered magnetic films with a magnetic retentivity of 1.3 T. The topography image and magnetic field distribution image are measured using an atomic force microscope and a magnetic force microscope, respectively. Using a silicon molding technique complemented by a lift-off process, NdFeB magnetic powder is utilized to fabricate magnetic microstructures. Silicon trenches as narrow as 20 μm are filled by a mixture of magnetic powder and wax powder. The B-H hysteresis loop of the patterned magnetic powder is characterized using a vibrating sample magnetometer, which shows a magnetic retentivity of approximately 0.37 T. - Highlights: → We demonstrate the fabrication of micro-magnets using silicon molding processes. → NdFeB/Ta films are well filled in silicon trenches with a thickness of 12 μm. → The 12-μm-thick NdFeB/Ta magnetic film shows a retentivity of 1.3 T. → Magnetic structures as narrow as 20 μm are fabricated using NdFeB magnetic powder. → VSM measurement shows a retentivity of 0.37 T for patterned NdFeB magnetic powder.

Fabrication of NdFeB microstructures using a silicon molding technique for NdFeB/Ta multilayered films and NdFeB magnetic powder

Energy Technology Data Exchange (ETDEWEB)

Jiang Yonggang, E-mail: yonggangj@gmail.com [School of Mechanical Engineering and Automation, Beihang University, Xueyuan Road No. 37, Haidian District, Beijing 100191 (China); Maenaka Human-Sensing Fusion project, Japan Science and Technology Agency, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Fujita, Takayuki [Maenaka Human-Sensing Fusion project, Japan Science and Technology Agency, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Graduate School of Engineering, University of Hyogo, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Uehara, Minoru [NEOMAX Co. Ltd., 2-15-17, Egawa, Shimamoto-Cho, Mishima-gun, Osaka 618-0013 (Japan); Iga, Yuki [Maenaka Human-Sensing Fusion project, Japan Science and Technology Agency, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Hashimoto, Taichi [Graduate School of Engineering, University of Hyogo, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Hao, Xiuchun; Higuchi, Kohei [Maenaka Human-Sensing Fusion project, Japan Science and Technology Agency, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Maenaka, Kazusuke [Maenaka Human-Sensing Fusion project, Japan Science and Technology Agency, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan); Graduate School of Engineering, University of Hyogo, 2167 Shosha, Himeji, Hyogo 671-2280 (Japan)

2011-11-15

The silicon molding technique is described for patterning of NdFeB/Ta multilayered magnetic films and NdFeB magnetic powder at the micron scale. Silicon trenches are seamlessly filled by 12-{mu}m-thick NdFeB/Ta multilayered magnetic films with a magnetic retentivity of 1.3 T. The topography image and magnetic field distribution image are measured using an atomic force microscope and a magnetic force microscope, respectively. Using a silicon molding technique complemented by a lift-off process, NdFeB magnetic powder is utilized to fabricate magnetic microstructures. Silicon trenches as narrow as 20 {mu}m are filled by a mixture of magnetic powder and wax powder. The B-H hysteresis loop of the patterned magnetic powder is characterized using a vibrating sample magnetometer, which shows a magnetic retentivity of approximately 0.37 T. - Highlights: > We demonstrate the fabrication of micro-magnets using silicon molding processes. > NdFeB/Ta films are well filled in silicon trenches with a thickness of 12 {mu}m. > The 12-{mu}m-thick NdFeB/Ta magnetic film shows a retentivity of 1.3 T. > Magnetic structures as narrow as 20 {mu}m are fabricated using NdFeB magnetic powder. > VSM measurement shows a retentivity of 0.37 T for patterned NdFeB magnetic powder.

Development of equipment for fabricating DUPIC fuel powder

International Nuclear Information System (INIS)

Kim, Ki Ho; Yang, M. S.; Park, J. J.; Lee, J. W.; Kim, J. H.; Cho, K. H.; Lee, D. Y.; Lee, Y. S.; Na, S. H.

1999-06-01

The powder fabrication processes, as the first stage of manufacturing DUPIC (Direct Use of PWR spent fuel In CANDU) fuel, consist of the slitting of spent PWR fuel rods, REOX (Oxidation and REduction of Oxide Fuels) processing to produce the powder feedstock, the milling of the produced powder, the granulation of the milled powder, and the mixing of the granulated powder with pressing lubricants. All these processes should be conducted by remote means in a hot-cell environment where the direct human access is limited to the strictest minimum due to the high radioactivity. This report describe the development of the equipment for fabricating DUPIC fuel powder. These equipment are Slitting Machine, Oxidation and Reduction (OREOX) Furnace, Mill, Roll Compactor, and Mixer. Remote design concept was applied to all the equipment for use in the M6 hot-cell of the IMEF. Mechanical design considerations and capabilities of the equipment for remote operation and maintenance are presented. First prototypes were developed and installed in the DUPIC full scale mock-up and tested using a master-slave manipulator. Redesign and reconstruction were made on each equipment based on mock-up test results. The remote technology acquired through this research was utilized in developing other equipment for DUPIC fuel fabrication, thereby improving safety and increasing productivity. This technology could also be extended to the area of remote handling equipment development for use in hazardous environments. (author). 14 refs., 9 tabs., 21 figs

Development of equipment for fabricating DUPIC fuel powder

Energy Technology Data Exchange (ETDEWEB)

Kim, Ki Ho; Yang, M. S.; Park, J. J.; Lee, J. W.; Kim, J. H.; Cho, K. H.; Lee, D. Y.; Lee, Y. S.; Na, S. H

1999-06-01

The powder fabrication processes, as the first stage of manufacturing DUPIC (Direct Use of PWR spent fuel In CANDU) fuel, consist of the slitting of spent PWR fuel rods, REOX (Oxidation and REduction of Oxide Fuels) processing to produce the powder feedstock, the milling of the produced powder, the granulation of the milled powder, and the mixing of the granulated powder with pressing lubricants. All these processes should be conducted by remote means in a hot-cell environment where the direct human access is limited to the strictest minimum due to the high radioactivity. This report describe the development of the equipment for fabricating DUPIC fuel powder. These equipment are Slitting Machine, Oxidation and Reduction (OREOX) Furnace, Mill, Roll Compactor, and Mixer. Remote design concept was applied to all the equipment for use in the M6 hot-cell of the IMEF. Mechanical design considerations and capabilities of the equipment for remote operation and maintenance are presented. First prototypes were developed and installed in the DUPIC full scale mock-up and tested using a master-slave manipulator. Redesign and reconstruction were made on each equipment based on mock-up test results. The remote technology acquired through this research was utilized in developing other equipment for DUPIC fuel fabrication, thereby improving safety and increasing productivity. This technology could also be extended to the area of remote handling equipment development for use in hazardous environments. (author). 14 refs., 9 tabs., 21 figs.

Optimisation of the magnetic properties of mechanically milled R5.5Fe73.5-xCoxCr3B18 nanocomposites

International Nuclear Information System (INIS)

O'Sullivan, J.F.; Smith, P.A.I.; Coey, J.M.D.

1998-01-01

Mechanical milling and subsequent annealing of R 4.5 R'Fe 73.5-x Co x Cr 3 B 18 (R=Nd,Pr and R'=Tb,Dy) ingots has been found to produce hard magnetic nanocomposites of (R,R') 2 (Fe,Co) 14 B, (Fe,Cr) 2 B and α-(Fe,Co) phases. Here we report on the optimisation of the composition of such nanocomposites. Substituting different rare-earth metals has a significant effect on the magnetic properties. The replacement of Nd with Pr produces higher coercivity and remanence, and better loop squareness. However, the replacement of Tb with Dy produced inferior properties when the main rare-earth component was Nd. Improved properties were obtained with the combination of Pr and Dy or Tb. Substitution of Co for Fe was found to lower coercivity but increase the remanence. The best combination of properties measured was for Pr 4.5 Dy 1 Fe 68.5 Co 5 Cr 3 B 1x , where H c =0.41 MA/m, J r =1 T, and (BH) max for the powder was 100 kJ/m 3 . These results will be discussed in terms of the grain size and the intrinsic properties of the hard and soft magnetic phases identified using X-ray diffraction. (orig.)

Microstructural and magnetic behavior of nanostructured soft alloys prepared by mechanical grinding and gas atomization

International Nuclear Information System (INIS)

Marin, P.; Lopez, M.; Garcia-Escorial, A.; Lieblich, M.

2007-01-01

Nanocrystalline powder of Fe-Si-B-Cu-Nb has been obtained by means of mechanical milling of the corresponding nanocrystalline ribbons. Gas atomization technique has been used to minimize the magnetic hardening due to stress effects observed in ball-milled samples. Fe-Si-B-Cu-Nb and Fe-Si nanocrystalline samples have been prepared by gas atomization. The aim of our work is to analyse the particle size dependence of coercivity in this nanostructured alloys and to show the analogies and differences between ball-milled and gas atomized samples

Polydimethylsiloxane films doped with NdFeB powder: magnetic characterization and potential applications in biomedical engineering and microrobotics.

Science.gov (United States)

Iacovacci, V; Lucarini, G; Innocenti, C; Comisso, N; Dario, P; Ricotti, L; Menciassi, A

2015-12-01

This work reports the fabrication, magnetic characterization and controlled navigation of film-shaped microrobots consisting of a polydimethylsiloxane-NdFeB powder composite material. The fabrication process relies on spin-coating deposition, powder orientation and permanent magnetization. Films with different powder concentrations (10 %, 30 %, 50 % and 70 % w/w) were fabricated and characterized in terms of magnetic properties and magnetic navigation performances (by exploiting an electromagnet-based platform). Standardized data are provided, thus enabling the exploitation of these composite materials in a wide range of applications, from MEMS/microrobot development to biomedical systems. Finally, the possibility to microfabricate free-standing polymeric structures and the biocompatibility of the proposed composite materials is demonstrated.

Preliminary study of sintering of metallic niobium processed for mechanical milling

International Nuclear Information System (INIS)

Tamura, H.M.; Vurobi Junior, S.; Cintho, O.M.; Sandim, H.R.Z.; Leite, G.S.

2010-01-01

In present study was preliminary study of mechanical milling influence on preparing of metallic niobium powder for sintering. Sample of metallic niobium in powder passing in sieve no. 635 mesh was processed by mechanical milling in SPEX mill for 8 hours using power grinding of 7:1 and a nitrogen atmosphere. The powder was annealed at different temperatures, 900 deg C, 1000 deg C, 1100 deg C and 1200 deg C for 1 hour in an atmosphere of hydrogen and argon to study their crystallization, which then were formed into blank for analysis of the curves compressibility. These samples were also subjected to x-ray diffraction in that their data were compared between the annealing temperatures. We also evaluate the compressibility curves of niobium samples with and without grinding these samples were subjected to x-ray diffraction and fluorescence. (author)

Magnetic and frequency properties for nanocrystalline Fe-Ni alloys prepared by high-energy milling method

International Nuclear Information System (INIS)

Liu Yongsheng; Zhang Jincang; Yu, Liming; Jia Guangqiang; Jing Chao; Cao Shixun

2005-01-01

Fe-based nano-crystalline soft magnetic alloy with Ni-doping was fabricated successfully by high-energy milling. It was proved that a Fe-Ni solid solution is formed and the evaluated average grain size is about 20 nm. The effect of doping Ni on the frequency properties was systematically investigated. From the magnetic measurement results, it can be concluded that, the nickel doped decreases the resonance frequency of Fe-Ni alloy, but Ni doping enhances the frequency stability. The corresponding value of initial permeability as a function of Ni doping concentration was given at 10 kHz and the result indicates that the peak value of initial permeability shifts to the region of low Ni concentration for the samples milled for 72 h

Development of Ferrite-Coated Soft Magnetic Composites: Correlation of Microstructure to Magnetic Properties

Science.gov (United States)

Sunday, Katie Jo

milling and analyzed for magnetic core loss dependence on particle size, cure temperature, and microstructure of both coating and core powder. We present a significant increase in core loss related to eddy current loss from coating particles sintering and Fe grain growth. Lastly, a more resistive coating material, NiZnCu-ferrite, is applied for improved resistivity, which leads to lower eddy current loss and improved magnetic performance. By highlighting the importance of microstructure and composition on magnetic properties, a closer look at interfacial features and local microstrain are necessary and accomplished in this work. Future developments of ferrite-based SMC coatings are required to transform the use of electromagnetic devices in today's society.

Preparation of tungsten-iron carbide by ball milling

International Nuclear Information System (INIS)

Wang, G.M.; Campbell, S.J.; Calka, A.; Kaczmarek, W.A.

1996-01-01

Several sets of elemental powder mixtures of Fe-W-C (W 46 Fe 46 C 8 , W 60 Fe 20 C 20 and W 34 Fe 33 C 33 ) were ball milled using Uni-Ball mill for periods of up to 550 h in vacuum with a ball - to - powder ratio of about 35:1. Depending on the milling time, the main component of the as-milled materials was found to be solid solutions of Fe-W-C or Fe-C. Ternary phase W 3 Fe 3 C was obtained on annealing the as-milled materials at about 700 deg C. This product was then found to transfer to (FeW) 6 C on heat treatment at about 800 deg C. The resultant products of the annealing processes were found to depend not only on the annealing temperature, but also the starting composition, especially the initial carbon concentration. Detailed information on the structural and phase evolution during thermal treatment as measured using x-ray diffraction, Moessbauer spectroscopy and thermal analysis is presented. Special interest is focused on the competition for formation in this system between the Fe-C, W-Fe and W-C phases

The role of silicon on the microstructure and magnetic behaviour of nanostructured (Fe{sub 0.7}Co{sub 0.3}){sub 100−x}Si{sub x} powders

Energy Technology Data Exchange (ETDEWEB)

Hocine, M. [Département de Génie Mécanique, Faculté de Technologies, Université de M' sila, B.P 166 Ichbelia, M' sila (Algeria); UR-MPE, M' hamed Bougara University, Boumerdes, 35000 Algeria (Algeria); Guittoum, A., E-mail: aguittoum@gmail.com [Nuclear Research Centre of Algiers, 02Bd Frantz Fanon, BP 399, Alger-Gare, Algiers (Algeria); Hemmous, M. [Nuclear Research Centre of Algiers, 02Bd Frantz Fanon, BP 399, Alger-Gare, Algiers (Algeria); Martínez-Blanco, D. [SCTs, University of Oviedo, EPM, Mieres, 33600 Spain (Spain); Gorria, P. [Department of Physics, EPI, University of Oviedo, Gijón, 33203 Spain (Spain); Rahal, B. [Nuclear Research Centre of Algiers, 02Bd Frantz Fanon, BP 399, Alger-Gare, Algiers (Algeria); Blanco, J.A. [Department of Physics, University of Oviedo, CalvoSotelo St., Oviedo, 330 07 Spain (Spain); Sunol, J.J. [Departament de Fisica, Universitat de Girona, Campus de Montillivi, Girona, 17071 Spain (Spain); Laggoun, A. [UR-MPE, M' hamed Bougara University, Boumerdes, 35000 Algeria (Algeria)

2017-01-15

Single-phase(Fe{sub 0.7}Co{sub 0.3}){sub 100−x}Si{sub x} nanostructured powders (x=0,5, 10, 15 and 20) have been elaborated by mechanical alloying in order to investigate the effect of silicon on the microstructure and magnetic properties of these alloys. A disordered Fe(Co, Si) solid solution with body centred cubic (bcc) crystal structure is formed after 72 h of milling for all the compositions. The addition of Si gives rise to a progressive decrease of the lattice parameter, from about 2.865 Å for the binary Fe{sub 70}Co{sub 30} compound down to 2.841 Å for the powder with x=20. The sample with the uppermost Si content exhibits the lowest value for the mean grain size (≈10 nm) as well as the largest microstrain (above 1.1%). All the samples are ferromagnetic at room temperature, although the saturation magnetization value reduces almost linearly by adding Si to the composition. A similar trend is observed for the hyperfine magnetic field obtained from the analysis of the room temperature Mössbauer spectra. The hyperfine field distributions show a broad double-peak shape for x>0, which can be ascribed to multiple local environments for the Fe atoms inside a disordered solid solution. - Highlights: • Single-phase (Fe{sub 0.7}Co{sub 0.3}){sub 100−x}Si{sub x} nanostructured powders (x=0, 5, 10, 15 and 20) have been elaborated by mechanical alloying. • The sample with the uppermost Si content exhibits the lowest value for the mean grain size. • The magnetic and hyperfine parameters of (Fe{sub 0.7}Co{sub 0.3}){sub 100−x}Si{sub x} depended intimately on Si content.

Structure and soft magnetic properties of the bulk samples prepared by compaction of the mixtures of Co-based and Fe-based powders

International Nuclear Information System (INIS)

Fuezer, J.; Bednarcik, J.; Kollar, P.; Roth, S.

2007-01-01

Ball milling of CoFeZrB ribbons and subsequent compaction of the resulting powders were used to prepare bulk amorphous samples. Further, two sets of powder samples were prepared by cryomilling of FeCuNbMoSiB alloy in amorphous and nanocrystalline state. Amorphous and nanocrystalline FeCuNbMoSiB powders were blended with CoFeZrB powder at different concentrations. Such powder mixtures were consolidated and several bulk nanocomposites have been synthesized. An addition of nanocrystalline or amorphous FeCuNbMoSiB powder to amorphous CoFeZrB powder caused a decrease of the magnetostriction of the resultant bulk samples, while the coercivity shows an opposite behavior. Our results show that the powder consolidation by hot pressing is an alternative method for the preparation of bulk metallic glasses, which are difficult to prepare by casting methods

Mechanically alloyed PrFeB nanocrystalline magnets

International Nuclear Information System (INIS)

Kaszuwara, W.; Leonowicz, M.

1998-01-01

Mechanically alloyed PrFeB nanocrystalline magnets were prepared by extensive ball milling of Pr, Fe and Fe 80 B 20 powders, followed by diffusion annealing. After milling, the material consisted of nanocrystalline α-Fe crystallites embedded in amorphous Pr-rich matrix. Thermomagnetic and calorimetric investigations of the transformations which occurred during annealing showed that the amorphous phase crystallised at 240 C, leading to the formation of crystalline Pr having lattice constants 10% greater than those shown in the ASTM data. This fact indicated that mechanical alloying and low temperature annealing led to the formation of a solid solution of either Fe or B in Pr, which does not exist in the equilibrium state. The Pr 2 Fe 14 B phase was subsequently formed within a temperature range of 420-620 C. The magnetic properties of magnets depend on the phase structure and grain size. Milling time appears to be a decisive processing parameter for the tailoring of the magnetic properties. Depending on the phase structure, the coercivities varied from 100 to 1200 kA/m and, respectively, the remanences from 0.98 T to 0.6 T. The highest maximum energy product was 80 kJ/m 3 . (orig.)

CaO-matrix processing of MnBi alloys for permanent magnets

Directory of Open Access Journals (Sweden)

A. M. Gabay

2017-05-01

Full Text Available The possibility to suppress agglomeration of MnBi alloy particles during milling and their unwanted sintering during subsequent annealing was explored by embedding the particles in CaO through co-milling. A 15 h annealing of the micron-sized MnBi particles embedded in the CaO matrix at 300 °C is not accompanied by sintering or growth of the particles while it significantly increases their coercivity – presumably by healing the milling-induced crystal defects. After separation from the CaO matrix, the annealed MnBi powder combines a calculated energy product of 10 MGOe with a room-temperature coercivity of 14.4 kOe. At the same time, the partial loss and degradation of the MnBi low-temperature phase during warm compaction of the powders makes the effect of the CaO-matrix annealing less pronounced in the case of fully dense magnets; the residue from the solvents employed for the removal of the CaO might have contributed to the decline of the properties. Still, a relatively high room-temperature coercivity of 8.5 kOe was obtained for the fuslly-dense MnBi magnet exhibiting an energy product of 5.3 MGOe.

Evaluating the Johanson theory for titanium powder

CSIR Research Space (South Africa)

Chikosha, S

2015-05-01

Full Text Available . In this study, the Johanson theory was used to determine the rolling parameters of titanium powder. Preliminary results of the nip angle, nip pressures and maximum horizontal pressures of the mill for the powder rolled on a 55mm diameter roll with roll gap sizes...

A study of Al-Mo powder processing as a possible way to corrosion resistent aluminum-alloys

Directory of Open Access Journals (Sweden)

Wilson Corrêa Rodrigues

2009-06-01

Full Text Available Elementary Al and Mo powder mixtures have been processed by high energy ball milling up to milling times of 100 hours. The shift of the pitting potential and the X ray analysis of green milled samples showed that part of the Mo has formed a supersaturated solid solution of Mo in Al. Elementary Mo powder, however, was still present after 100 hours of milling. Sintering led to the formation of the intermetallic Al12Mo phase.

Compact Process for the Preparation of Microfine Spherical High-Niobium-Containing TiAl Alloy Powders

Science.gov (United States)

Tong, J. B.; Lu, X.; Liu, C. C.; Wang, L. N.; Qu, X. H.

2015-03-01

High-Nb-containing TiAl alloys are a new generation of materials for high-temperature structural applications because of their superior high-temperature mechanical properties. The alloy powders can be widely used for additive manufacturing, thermal spraying, and powder metallurgy. Because of the difficulty of making microfine spherical alloy powders in quantity by conventional techniques, a compact method was proposed, which consisted of two-step ball milling of elemental powders and subsequent radio frequency (RF) argon plasma spheroidization. In comparison with conventional mechanical alloying techniques, the two-step milling process can be used to prepare alloy powders with uniform scale in a short milling time with no addition of process control agent. This makes the process effective and less contaminating. After RF argon plasma spheroidization, the powders produced exhibit good sphericity, and the number-average diameter is about 8.2 μm with a symmetric unimodal particle size distribution. The powders perform high composition homogeneity and contain predominately supersaturated α 2-Ti3Al phase. The oxygen and carbon contents of the spheroidized powder are 0.47% and 0.050%, respectively.

Synthesis of the Mg2Ni alloy prepared by mechanical alloying using a high energy ball mill

International Nuclear Information System (INIS)

Iturbe G, J. L.; Lopez M, B. E.; Garcia N, M. R.

2010-01-01

Mg 2 Ni was synthesized by a solid state reaction from the constituent elemental powder mixtures via mechanical alloying. The mixture was ball milled for 10 h at room temperature in an argon atmosphere. The high energy ball mill used here was fabricated at ININ. A hardened steel vial and three steel balls of 12.7 mm in diameter were used for milling. The ball to powder weight ratio was 10:1. A small amount of powder was removed at regular intervals to monitor the structural changes. All the steps were performed in a little lucite glove box under argon gas, this glove box was also constructed in our Institute. The structural evolution during milling was characterized by X-ray diffraction and scanning electron microscopy techniques. The hydrogen reaction was carried out in a micro-reactor under controlled conditions of pressure and temperature. The hydrogen storage properties of mechanically milled powders were evaluated by using a thermogravimetric analysis system. Although homogeneous refining and alloying take place efficiently by repeated forging, the process time can be reduced to one fiftieth of the time necessary for conventional mechanical milling and attrition. (Author)

The grinding behavior of ground copper powder for Cu/CNT nanocomposite fabrication by using the dry grinding process with a high-speed planetary ball mill

Science.gov (United States)

Choi, Heekyu; Bor, Amgalan; Sakuragi, Shiori; Lee, Jehyun; Lim, Hyung-Tae

2016-01-01

The behavior of ground copper powder for copper-carbon nanotube (copper-CNT) nanocomposite fabrication during high-speed planetary ball milling was investigated because the study of the behavior characteristics of copper powder has recently gained scientific interest. Also, studies of Cu/CNT composites have widely been done due to their useful applications to enhanced, advanced nano materials and components, which would significantly improve the properties of new mechatronics-integrated materials and components. This study varied experimental conditions such as the rotation speed and the grinding time with and without CNTs, and the particle size distribution, median diameter, crystal structure and size, and particle morphology were monitored for a given grinding time. We observed that pure copper powders agglomerated and that the morphology changed with changing rotation speed. The particle agglomerations were observed with maximum experiment conditions (700 rpm, 60 min) in this study of the grinding process for mechanical alloys in the case of pure copper powders because the grinding behavior of Cu/CNT agglomerations was affected by the addition of CNTs. Indeed, the powder morphology and the crystal size of the composite powder could be changed by increasing the grinding time and the rotation speed.

Effect of ball mill treatment on kinetics of amorphous Ni78Si10B12 alloy crystallization

International Nuclear Information System (INIS)

Tomilin, I.A.; Mochalova, T.Yu.; Kaloshkin, S.D.; Kostyukovich, T.G.; Lopatina, E.A.

1993-01-01

The effect of the parameters of Ni 78 Si 10 B 12 alloy amorphous strip milling in a ball planetary mill on the stability of powder amorphous state, crytallization kinetics and dispersity is studied by the methods of differential scanning microcaloremetry and X-ray diffraction analysis. Energy intensity of milling conditions is assessed. An increase of input energy results in a decrease of activation energy of powder crystallization. Strip milling parameters which enable to avaintain the amorphous state of the material are determined

Effects of microstructures on the performance of rare-earth-free MnBi magnetic materials and magnets

Science.gov (United States)

Nguyen, Vuong Van; Nguyen, Truong Xuan

2018-03-01

Since the solidification of MnBi alloys is peritectic, their microstructures always consist of the starting phases of Mn and Bi and the productive phase MnBi. The high performance of MnBi bulk magnets requires appropriate routes of preparing MnBi powders of high spontaneous magnetization Ms and large coercivity iHc as well a route of producing bulk magnets thereof. In these routes, the microstructures of arc-melted alloys, annealed alloys and magnets strongly related to the quality of powders and the performance of magnets. The paper proves that: i) The microstructure of fine Mn-inclusions embedded in the matrix of Bi is preferred for arc-melted alloys to realize the rapid evolution of the ferromagnetic phase inside them during their sequent annealing process; ii) The time-controlled annealing process plays a key role in controlling the microstructure with the main ferromagnetic phase matrix, in which the rest of Mn and the Bi accumulations are embedded; iii) The cold (in-liquid-nitrogen) ball milling annealed alloys is required for preparing a high quality powders with the preferred sub-micrometer microstructure without a Bi-decomposition; iv) The short-time warm compaction is crucial to fabricate dense, highly textured bulk magnets with the micrometer microstructure. The realization and control of these preferred microstructures figured in these routes enhance the chance of preparing MnBi bulk magnets with the energy product (BH)max larger than 8 MGOe.

Fabrication and Magnetic Properties of Co₂MnAl Heusler Alloys by Mechanical Alloying.

Science.gov (United States)

Lee, Chung-Hyo

2018-02-01

We have applied mechanical alloying (MA) to produce nanocrystalline Co2MnAl Heusler alloys using a mixture of elemental Co50Mn25Al25 powders. An optimal milling and heat treatment conditions to obtain a Co2MnAl Heusler phase with fine microstructure were investigated by X-ray diffraction, differential scanning calorimeter and vibrating sample magnetometer measurements. α-(Co, Mn, Al) FCC phases coupled with amorphous phase are obtained after 3 hours of MA without any evidence for the formation of Co2MnAl alloys. On the other hand, a Co2MnAl Heusler alloys can be obtained by the heat treatment of all MA samples up to 650 °C. X-ray diffraction result shows that the average grain size of Co2MnAl Heusler alloys prepared by MA for 5 h and heat treatment is in the range of 95 nm. The saturation magnetization of MA powders decreases with MA time due to the magnetic dilution by alloying with nonmagnetic Mn and Al elements. The magnetic hardening due to the reduction of the grain size with ball milling is also observed. However, the saturation magnetization of MA powders after heat treatment increases with MA time and reaches to a maximum value of 105 emu/g after 5 h of MA. It can be also seen that the coercivity of 5 h MA sample annealed at 650 °C is fairly low value of 25 Oe.

Synthesis behavior of nanocrystalline Al-Al2O3 composite during low time mechanical milling process

International Nuclear Information System (INIS)

Alizadeh, Mostafa; Aliabadi, Morteza Mirzaei

2011-01-01

Research highlights: → In the low time milling the effect of Al 2 O 3 amount is investigated → Al 2 O 3 particles are distributed uniformly in the Al matrix → In the low time milling it is possible to produce nanostructured composite powder → Median size and bulk density measurements demonstrate reaching the steady state. - Abstract: In this work, four different volume fractions of Al 2 O 3 (10, 20, 30 and 40 vol.%) were mixed with the fine Al powder and the powder blends were milled for 5 h. Scanning electron microscopy analysis, particle size analysis and bulk density measurements were used to investigate the morphological changes and achieving the steady state conditions. The results showed that increasing the Al 2 O 3 content can provide the steady state particle size in 5 h milling process. It was found that increasing the volume fraction of Al 2 O 3 leads to increasing the uniformity of Al 2 O 3 . Standard deviations of microhardness measurements confirmed this result. The XRD pattern and XRF investigations depicted that increasing the Al 2 O 3 content causes an increase in the crystal defects, micro-strain and Fe contamination during 5 h milling process of nanocrystalline composite powders while the grain size is decreased. To investigate the effect of milling time, Al-30 vol.% Al 2 O 3 (which achieved steady state during 5 h milling process) was milled for 1-4 h. The results depicted that the milling time lower than 5 h, do not achieve to steady state conditions.

Structural analysis and magnetic properties of solid solutions of Co–Cr system obtained by mechanical alloying

Energy Technology Data Exchange (ETDEWEB)

Betancourt-Cantera, J.A. [Área Académica de Ciencias de la Tierra y Materiales, UAEH Carr., Pachuca-Tulancingo Km. 4.5, Pachuca, Hidalgo 42184 (Mexico); Sánchez-De Jesús, F., E-mail: fsanchez@uaeh.edu.mx [Área Académica de Ciencias de la Tierra y Materiales, UAEH Carr., Pachuca-Tulancingo Km. 4.5, Pachuca, Hidalgo 42184 (Mexico); Bolarín-Miró, A.M. [Área Académica de Ciencias de la Tierra y Materiales, UAEH Carr., Pachuca-Tulancingo Km. 4.5, Pachuca, Hidalgo 42184 (Mexico); Betancourt, I.; Torres-Villaseñor, G. [Departamento de Materiales Metálicos y Cerámicos, Instituto de Investigaciones en Materiales, Universidad Nacional Autónoma de México, México D.F. 04510 (Mexico)

2014-03-15

In this paper, a systematic study on the structural and magnetic properties of Co{sub 100−x}Cr{sub x} alloys (0powders were used as precursors, and mixed in an adequate weight ratio to obtain Co{sub 1−x}Cr{sub x} (0milling was carried out at room temperature in a shaker mixer mill using vials and balls of hardened steel as the milling media with a ball:powder weight ratio of 10:1. The mixtures were milled for 7 h. Results shown that after 7 h of milling time, solid solutions based on Co-hcp, Co-fcc and Cr-bcc structures were obtained. The saturation polarization indicated a maximum value of 1.17 T (144 Am{sup 2}/kg) for the Co{sub 90}Cr{sub 10}, which decreases with the increasing of the Cr content up to x=80, as a consequence of the dilution effect of the magnetic moment which is caused by the Cr content and by the competition between ferromagnetic and antiferromagnetic exchange interactions. The coercivity increases up to 34 kA/m (435 Oe) for Co{sub 40}Cr{sub 60}. For Cr rich compositions, it is observed an important decrease reaching 21 kA/m (272 Oe) for Co{sub 10}Cr{sub 90,} it is related to the grain size and the structural change. Besides, the magnetic anisotropy constant was determined for each composition. Magnetic thermogravimetric analysis allowed to obtain Curie temperatures corresponding to the formation of hcp-Co(Cr) and fcc-Co(Cr) solid solutions. - Highlights: • Mechanical alloying (MA) induces the formation of solid solutions of Co–Cr system in non-equilibrium. • We report the crystal structure and the magnetic behavior of Co–Cr alloys produced by MA. • MA improves the magnetic properties of Co–Cr system.

Effect of milling on the damping behavior of nano-structured copper

Energy Technology Data Exchange (ETDEWEB)

Srikanth, Narasimalu; Thein, Maung Aye; Gupta, Manoj

2004-02-05

In the present study, elemental Cu powder was mechanically milled (MMed) for 10 h to reduce the grain (crystalline) size in the nano-range (<100 nm). The mechanically milled powder (10 h-MMed) and elemental powder without mechanical milling (MM) (0 h-MMed) was consolidated by die-cold compaction and were further hot extruded at different temperatures to maintain a crystallite size within the nano-range. Further, the specimen was tested by a novel free-free type suspended beam arrangement, coupled with circle-fit approach to determine damping characteristics. The characterization results help to understand the effect of the nano-size grains on the overall damping capacity of the bulk samples compared to a normal micro-crystalline sample. Results show that the damping capacity of the nano-grained material increases due to the presence of process induced microstructural changes similar to the damping behavior of a micro-grain sized specimen.

Fabrication of Fe-Cr-Mo powder metallurgy steel via a mechanical-alloying process

Science.gov (United States)

Park, Jooyoung; Jeong, Gowoon; Kang, Singon; Lee, Seok-Jae; Choi, Hyunjoo

2015-11-01

In this study, we employed a mechanical-alloying process to manufacture low-alloy CrL and CrM steel powders that have similar specifications to their water-atomized counterparts. X-ray diffraction showed that Mo and Cr are alloyed in Fe after four cycles of planetary milling for 1 h at 150 RPM with 15-min pauses between the cycles (designated as P2C4 process). Furthermore, the measured powder size was found to be similar to that of the water-atomized counterparts according to both scanning electron microscope images and laser particle size analysis. The samples were sintered at 1120 °C, after which the P2C4-milled CrL showed similar hardness to that of water-atomized CrL, whereas the P2C4-milled CrM showed about 45% lower hardness than that of its water-atomized counterpart. Water-atomized CrM consists of a well-developed lathtype microstructure (bainite or martensite), while a higher fraction of polygonal ferrite is observed in P2C4-milled CrM. This phase difference causes the reduction of hardness in the P2C4-milled CrM, implying that the phase transformation behavior of specimens produced via powder metallurgy is influenced by the powder fabrication method.

Magnetic properties of La{sub 0.7}Ca{sub 0.3}MnO{sub 3} nanoparticles prepared by reactive milling

Energy Technology Data Exchange (ETDEWEB)

Do Hung Manh [Institute of Materials Science, Vietnamese Academy of Science and Technology, 18 Hoang Quoc Viet Road, Cau Giay Distr., Hanoi (Viet Nam)], E-mail: manhdh@ims.vast.ac.vn; Nguyen Chi Thuan [Institute of Materials Science, Vietnamese Academy of Science and Technology, 18 Hoang Quoc Viet Road, Cau Giay Distr., Hanoi (Viet Nam); Pham Thanh Phong [Nha Trang Pedagogic College, Khanh Hoa Province (Viet Nam); Le Van Hong; Nguyen Xuan Phuc [Institute of Materials Science, Vietnamese Academy of Science and Technology, 18 Hoang Quoc Viet Road, Cau Giay Distr., Hanoi (Viet Nam)

2009-06-24

La{sub 0.7}Ca{sub 0.3}MnO{sub 3} (LCMO) nanoparticles were synthesized by reactive milling in ambient conditions. Magnetic properties of LCMO single-phase nanocrystalline particles were studied. LCMO nanoparticles exhibit superparamagnetism with blocking temperature that decreases in the logarithmic function as increasing applied magnetic field. Besides, the blocking temperature decreases as increasing milling time from 8 h to 16 h. The temperature dependence of the saturation magnetization shows a strong collective excitation due to the spin wave that depends on temperature in form T{sup {alpha}} with {alpha} = 1.7, which slightly deviates from the Bloch law.

Spark Plasma Co-Sintering of Mechanically Milled Tool Steel and High Speed Steel Powders.

Science.gov (United States)

Pellizzari, Massimo; Fedrizzi, Anna; Zadra, Mario

2016-06-16

Hot work tool steel (AISI H13) and high speed steel (AISI M3:2) powders were successfully co-sintered to produce hybrid tool steels that have properties and microstructures that can be modulated for specific applications. To promote co-sintering, which is made difficult by the various densification kinetics of the two steels, the particle sizes and structures were refined by mechanical milling (MM). Near full density samples (>99.5%) showing very fine and homogeneous microstructure were obtained using spark plasma sintering (SPS). The density of the blends (20, 40, 60, 80 wt % H13) was in agreement with the linear rule of mixtures. Their hardness showed a positive deviation, which could be ascribed to the strengthening effect of the secondary particles altering the stress distribution during indentation. A toughening of the M3:2-rich blends could be explained in view of the crack deviation and crack arrest exerted by the H13 particles.

Spark Plasma Co-Sintering of Mechanically Milled Tool Steel and High Speed Steel Powders

Directory of Open Access Journals (Sweden)

Massimo Pellizzari

2016-06-01

Full Text Available Hot work tool steel (AISI H13 and high speed steel (AISI M3:2 powders were successfully co-sintered to produce hybrid tool steels that have properties and microstructures that can be modulated for specific applications. To promote co-sintering, which is made difficult by the various densification kinetics of the two steels, the particle sizes and structures were refined by mechanical milling (MM. Near full density samples (>99.5% showing very fine and homogeneous microstructure were obtained using spark plasma sintering (SPS. The density of the blends (20, 40, 60, 80 wt % H13 was in agreement with the linear rule of mixtures. Their hardness showed a positive deviation, which could be ascribed to the strengthening effect of the secondary particles altering the stress distribution during indentation. A toughening of the M3:2-rich blends could be explained in view of the crack deviation and crack arrest exerted by the H13 particles.

Effect of heat treatment on Fe-B-Si-Nb alloy powder prepared by mechanical alloying

Directory of Open Access Journals (Sweden)

Rodrigo Estevam Coelho

2005-06-01

Full Text Available The effect of heat treatment on crystallization behavior of Fe73.5B15Si10Nb1.5 alloy powder prepared by mechanical alloying was studied. The powder samples were prepared by mechanical alloying (MA and for different milling times (1, 5, 25, 70 and 100 hours. Crystalline powders of iron, boron, silicon and niobium were sealed with tungsten carbide balls in a cylindrical vial under nitrogen atmosphere. The ball-to-powder weight ratio was 20 to 1. A Fritsch Pulverizette 5 planetary ball mill was used for MA the powders at room temperature and at 250 rpm. To study the microstructural evolution, a small amount of powder was collected after different milling times and examined by X-ray diffraction, using CuKalpha radiation (lambda = 0.15418 nm. The crystallization behavior was studied by differential thermal analysis, from 25 up to 1000 °C at a heating rate of 25 °C min-1.

The influence of structural changes on electrical and magnetic characteristics of amorphous powder of the nixmoy alloy

Directory of Open Access Journals (Sweden)

Ribić-Zelenović Lenka

2006-01-01

Full Text Available Nickel and molybdenum alloy powder was electrodeposited on a titanium cathode from a NiSO4⋅7H2O and (NH46 Mo7O24⋅4H2O ammonium solution. The desired chemical composition, structure, size and shape of particles in the powder samples were achieved by an appropriate choice of electrolysis parameters (current density, composition and temperature of the solution, cathode material and electrolysis duration. Metal coatings form in the current density range 15 mA cm-2powders form. The chemical composition of powder samples depends on the current density of electrodeposition. The molybdenum content in the powder increases with the increase of current density (in the low current density range, while in the higher current density range the molybdenum content in the alloy decreases with the increase of the current density of deposition. Smaller sized particles form at higher current density. X-ray analysis, differential scanning calorimetric and measurements of the temperature dependence of electric resistance and magnetic permeability of the powder samples were all used to establish a predominantly amorphous structure of the powder samples formed at the current density of j≥70mA cm-2. The crystalline particle content in the powder samples increases with the decrease of the current density of deposition. Powder heating causes structural changes. The process of thermal stabilization of nickel and molybdenum amorphous powders takes place in the temperature interval from 463K to 573K and causes a decrease in electrical resistance and increase in magnetic permeability. The crystallization temperature depends on the value of current density of powder electrodeposition. Powder formed at j=180 mA cm-2 begins to crystallize at 573K, while the powder deposited at j=50 mA cm-2 begins to crystallize at 673K. Crystallization of the powder causes a decrease in electric resistivity and magnetic

Structure investigations of ferromagnetic Co-Ni-Al alloys obtained by powder metallurgy.

Science.gov (United States)

Maziarz, W; Dutkiewicz, J; Lityńska-Dobrzyńska, L; Santamarta, R; Cesari, E

2010-03-01

Elemental powders of Co, Ni and Al in the proper amounts to obtain Co(35)Ni(40)Al(25) and Co(40)Ni(35)Al(25) nominal compositions were ball milled in a high-energy mill for 80 h. After 40 h of milling, the formation of a Co (Ni, Al) solid solution with f.c.c. structure was verified by a change of the original lattice parameter and crystallite size. Analytical transmission electron microscopy observations and X-ray diffraction measurements of the final Co (Ni, Al) solid solution showed that the crystallite size scattered from 4 to 8 nm and lattice parameter a = 0.36086 nm. The chemical EDS point analysis of the milled powder particles allowed the calculation of the e/a ratio and revealed a high degree of chemical homogeneity of the powders. Hot pressing in vacuum of the milled powders resulted in obtaining compacts with a density of about 70% of the theoretical one. An additional heat treatment increased the density and induced the martensitic transformation in a parent phase. Selected area diffraction patterns and dark field images obtained from the heat-treated sample revealed small grains around 300 nm in diameter consisting mainly of the ordered gamma phase (gamma'), often appearing as twins, and a small amount of the L1(0) ordered martensite.

Study of the influence of thermal treatment on the magnetic properties of lithium ferrite prepared by wet ball-milling using nitrates as raw material

Energy Technology Data Exchange (ETDEWEB)

Teixeira, S. Soreto, E-mail: silvia.soreto@ua.pt; Graça, M.P.F., E-mail: mpfg@ua.pt; Costa, L.C., E-mail: kady@ua.pt; Valente, M.A., E-mail: mav@ua.pt

2014-08-01

Graphical abstract: - Highlights: • The saturation magnetization increases with heat-treatment temperature until 1200 °C. • 1200 °C sample presents, at 5 K, a magnetic moment of 73 emu/g and 66 emu/g at 300 K. • Heat-treatment promotes the formation of lithium ferrate and hematite, decreasing the magnetic moment. - Abstract: Lithium ferrite (LiFe{sub 5}O{sub 8}) is an attractive material for several potential technological applications. Critical to such attractiveness are its physical properties, such as high Curie temperature, square hysteresis loop and high magnetization. Knowing that the properties of these crystals depend on the preparation method and raw materials, in this work LiFe{sub 5}O{sub 8} crystallites were obtained by controlled heat-treatments, between 200 and 1400 °C, of homogeneous Li{sub 2}O-Fe{sub 2}O{sub 3} powders prepared by wet ball-milling method and using lithium and iron nitrates as raw materials. LiFe{sub 5}O{sub 8} crystal phase was formed through heat-treatments at temperatures above 500 °C. At higher temperatures the formation of lithium ferrate and hematite is promoted, leading to a decrease in the magnetic moment. Heat-treated the sample at 1200 °C results in the highest levels of magnetic saturation, presenting a magnetic moment of 73 emu/g at 5 K and 66 emu/g at 300 K, respectively.

Grinding Si3N4 Powder In Si3N4 Equipment

Science.gov (United States)

Herbell, Thomas P.; Freedman, Marc R.; Kiser, James D.

1989-01-01

Three methods of grinding compared. Report based on study of grinding silicon nitride powder in preparation for sintering into solid ceramic material. Attrition, vibratory, and ball mills lined with reaction-bonded silicon nitride tested. Rates of reduction of particle sizes and changes in chemical compositions of powders measured so grinding efficiences and increases in impurity contents from wear of mills and media evaluated for each technique.

Magnetic and structural properties of Fe{sub 65}Co{sub 35} alloys obtained by melting, high-energy milling and heat treatment

Energy Technology Data Exchange (ETDEWEB)

Trifu, A.V.; Dorolti, E. [Faculty of Physics, Babes-Bolyai University, 400084 Cluj-Napoca (Romania); Takacs, A.F., E-mail: albert.takacs@phys.ubbcluj.ro [Faculty of Physics, Babes-Bolyai University, 400084 Cluj-Napoca (Romania); Chicinaş, I. [Materials Sciences and Engineering Department, Technical University of Cluj-Napoca, 103-105 Muncii Avenue, 400641 Cluj-Napoca (Romania); Isnard, O. [Institut Néel, CNRS, Université Joseph Fourier, BP 166X, 38042 Grenoble Cédex 9 (France); Pop, V. [Faculty of Physics, Babes-Bolyai University, 400084 Cluj-Napoca (Romania)

2013-11-20

The influence of milling and annealing conditions on the structural and magnetic behaviour of mechanically milled Fe{sub 65}Co{sub 35} alloys has been studied. By differential scanning calorimetry measurements we determined the internal stress relaxation temperature, recrystallisation temperature and structural order/disorder transition temperature of bulk and mechanical milled Fe{sub 65}Co{sub 35}. The width of the X-ray diffraction peaks was found to increase with the milling time. Two types of annealing were performed: a conventional heat treatment at 500, 550 and 600 °C for 2 h and a rapid annealing for a maximum of 2 min at 700, 750 or 800 °C followed by quenching. Crystallite size increases with increasing heat treatment temperature and time, as both are parameters that influence the magnetic properties of the sample. Magnetic permeability variations result from internal stress evolution, changes in crystallite size, supposing that the crystallite size of the annealed samples is at the border between viability of the Herzer model and the classical behaviour of the permeability vs. crystallite size.

Coercivity enhancement in (Ce,Nd)-Fe-B sintered magnets prepared by adding NdH{sub x} powders

Energy Technology Data Exchange (ETDEWEB)

Zhang, Le-le [Key Laboratory of Integrated Exploitation of Bayan Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); School of Science, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Li, Zhu-bai, E-mail: lzbgj@163.com [Key Laboratory of Integrated Exploitation of Bayan Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Ma, Qiang; Li, Yong-feng; Zhao, Qian [Key Laboratory of Integrated Exploitation of Bayan Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); School of Science, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Zhang, Xue-feng, E-mail: xuefeng056@163.com [Key Laboratory of Integrated Exploitation of Bayan Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); School of Science, Inner Mongolia University of Science and Technology, Baotou 014010 (China)

2017-08-01

(Ce,Nd)-Fe-B sintered magnets were prepared by the addition of NdH{sub x} powders in Ce{sub 9}Nd{sub 4.5}Fe{sub 80}B{sub 6.5} powders. The coercivity is rather low in Ce{sub 9}Nd{sub 4.5}Fe{sub 80}B{sub 6.5} magnets, and Ce element prefers to distribute at the outer-layer of main phase (Ce,Nd){sub 2}Fe{sub 14}B. The investigation of scanning electron microscope shows that the addition of NdH{sub x} powders leads to the increase of Nd content at grain outer-layer of main phase owing to the element diffusion. Magnetization reversal undergoes the nucleation of reversed domain wall at grain outer-later, and the addition of NdH{sub x} powders leads to the increase in the nucleation field of reversed domain, giving rise to the significant improvement of coercivity. The larger amount addition of NdH{sub x} powders leads to the increase in the amount of intergranular phase, resulting in the decreases of the remanence, the squareness of demagnetization curve and the maximum energy product.

Obtaining beta phase in Ti through processing in high energy mill powders of Ti and Nb; Obtencao de fase beta no Ti atraves de processamento em moinho de alta energia de pos de Ti e Nb

Energy Technology Data Exchange (ETDEWEB)

Milanez, Mateus; Ferretto, Aline; Rocha, Marcio Roberto da; Arnt, Angela Coelho [Universidade do Extremo Sul Catarinense (UNESC), Criciuma, SC (Brazil). Departamento de Engenharia de Materiais; Milanez, Alexandre [Faculdade SATC (FASATC), Criciuma, SC (Brazil). Departamento de Engenharia Mecanica; Schaeffer, Lirio [Universidade Federal do Rio Grande do Sul (LdTM/UFRGS), RS (Brazil). Lab. de Transformacao Mecanica

2014-07-01

An orthopedic implant, ideal, must meet the requirements of biocompatibility, have good mechanical properties among others. Titanium and Niobium exhibit biocompatibility and the β-Ti phase relationships have the highest strength / weight among all titanium alloys, presenting lower values of elastic modulus. The alloy has mechanically produced specific microstructural characteristics and improved mechanical properties compared with conventional powder metallurgy. In this study, a titanium alloy with different additions of niobium was used. The metal powders were mixed via mechanical alloy in high energy mill (attritor). The powder samples were analyzed by X-ray diffraction (X-RD) and property held by adhesive wear testing with a Pin-on-Disk. The present study revealed that through the high-energy milling is possible the atomic interaction between Ti and Nb particles and the mechanical properties are affected by the concentration of Nb. (author)

Synthesis of the Mg{sub 2}Ni alloy prepared by mechanical alloying using a high energy ball mill

Energy Technology Data Exchange (ETDEWEB)

Iturbe G, J. L.; Lopez M, B. E. [ININ, Departamento de Quimica, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Garcia N, M. R., E-mail: joseluis.iturbe@inin.gob.m [UNAM, Facultad de Estudios Superiores Zaragoza, Batalla 5 de Mayo s/n, Esq. Fuerte de Loreto, Col. Ejercito de Oriente, 09230 Mexico D. F. (Mexico)

2010-07-01

Mg{sub 2}Ni was synthesized by a solid state reaction from the constituent elemental powder mixtures via mechanical alloying. The mixture was ball milled for 10 h at room temperature in an argon atmosphere. The high energy ball mill used here was fabricated at ININ. A hardened steel vial and three steel balls of 12.7 mm in diameter were used for milling. The ball to powder weight ratio was 10:1. A small amount of powder was removed at regular intervals to monitor the structural changes. All the steps were performed in a little lucite glove box under argon gas, this glove box was also constructed in our Institute. The structural evolution during milling was characterized by X-ray diffraction and scanning electron microscopy techniques. The hydrogen reaction was carried out in a micro-reactor under controlled conditions of pressure and temperature. The hydrogen storage properties of mechanically milled powders were evaluated by using a thermogravimetric analysis system. Although homogeneous refining and alloying take place efficiently by repeated forging, the process time can be reduced to one fiftieth of the time necessary for conventional mechanical milling and attrition. (Author)

Magnetic properties of nanocrystalline pyrrhotite prepared by high-energy milling

DEFF Research Database (Denmark)

Balaz, P.; Godocikova, E.; Alacova, A.

2004-01-01

The nanocrystalline pyrrhotite was prepared by high-energy milling of lead sulphide with elemental Fe acting as reducing element. X-ray diffractometry, Mossbauer spectroscopy and VSM magnetometry were used to determine the properties of nanocrystalline iron sulphide prepared by the corresponding...... mechanochemical reaction. Pyrrhotite Fe1-xS together with the residual Fe metal were identified by the X-ray diffractometry. The kinetic studies performed by Mossbauer spectroscopy and VSM magnetometry allowed us to follow in more details the progress of the nanocrystalline magnetic phase formation during...

Structure and magnetic properties of nanostructured MnNi alloys fabricated by mechanical alloying and annealing treatments

Science.gov (United States)

Jalal, T.; Hossein Nedjad, S.; Khalili Molan, S.

2013-05-01

A nearly equiatomic MnNi alloy was fabricated from the elemental powders by means of mechanical alloying in a planetary ball milling apparatus. X-ray diffraction (XRD), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and measurements of magnetization were conducted to identify the structural states and properties of the prepared alloys. After ball milling for 20 h, a disordered face-centered cubic (f.c.c.) solid solution was formed which increased in lattice parameter by further milling up to 50 h. An exothermic reaction took place at around 300-400°C during continuous heating of the disordered f.c.c. solid solution. This reaction is attributed to a structural ordering leading to the formation of a face-centered tetragonal (f.c.t.) phase with L10 type ordering. Examination of the magnetic properties indicated that the structural ordering increases remnant magnetization and decreases coerecivity.

The cation inversion and magnetization in nanopowder zinc ferrite obtained by soft mechanochemical processing

International Nuclear Information System (INIS)

Milutinović, A.; Lazarević, Z.; Jovalekić, Č.; Kuryliszyn-Kudelska, I.; Romčević, M.; Kostić, S.; Romčević, N.

2013-01-01

Graphical abstract: - Highlights: • Nano powder of ZnFe 2 O 4 prepared by a soft mechanochemical route after 18 h milling. • Phase formation controlled by XRD, Raman spectroscopy and magnetic measurements. • Size, strain and cation inversion degree determined by Rietveld refinement. • We were able to estimate the degree of inversion at most 0.348 and 0.4. • Obtained extremely high values of saturation magnetizations at T = 4.5 K. - Abstract: Two zinc ferrite nanoparticle materials were prepared by the same method – soft mechanochemical synthesis, but starting from different powder mixtures: (1) Zn(OH) 2 /α-Fe 2 O 3 and (2) Zn(OH) 2 /Fe(OH) 3 . In both cases a single phase system was obtained after 18 h of milling. The progress of the synthesis was controlled by X-ray diffractometry (XRD), Raman spectroscopy, TEM and magnetic measurements. Analysis of the XRD patterns by Rietveld refinement allowed determination of the cation inversion degree for both obtained single phase ZnFe 2 O 4 samples. The sample obtained from mixture (1) has the cation inversion degree 0.3482 and the sample obtained from mixture (2) 0.400. Magnetization measurements were confirmed that the degrees of the inversion were well estimated. Comparison with published data shows that used method of synthesis gives nano powder samples with extremely high values of saturation magnetizations: sample (1) 78.3 emu g −1 and sample (2) 91.5 emu g −1 at T = 4.5 K

Preparation of iron sulphides by high energy ball milling

DEFF Research Database (Denmark)

Lin, R.; Jiang, Jianzhong; Larsen, R.K.

1998-01-01

The reaction of a powder mixture consisting of 50 a.% Fe and 50 a.% S during high energy ball milling has been studied by x-ray diffraction and Mossbauer spectroscopy. After around 19 h of milling FeS2 and FeS havebeen formed. By further milling the FeS compound becomes dominating and only Fe......S with an average crystallite size of about 10 nm was observed after milling times longer than 67 h. Mossbauer spectra obtained with applied fields show that the particles are antiferromagnetic or have a strongly canted spin structure....

Structural evolution of Fe-50 at.% Al powders during mechanical alloying and subsequent annealing processes

International Nuclear Information System (INIS)

Haghighi, Sh. Ehtemam; Janghorban, K.; Izadi, S.

2010-01-01

Iron aluminides, despite having desirable properties like excellent corrosion resistance, present low room-temperature ductility and low strength at high temperatures. Mechanical alloying as a capable process to synthesize nanocrystalline materials is under consideration to modify these drawbacks. In this study, the microstructure of iron aluminide powders synthesized by mechanical alloying and subsequent annealing was investigated. Elemental Fe and Al powders with the same atomic percent were milled in a planetary ball mill for 15 min to 100 h. The powder milled for 80 h was annealed at temperatures of 300, 500 and 700 o C for 1 h. The alloyed powders were disordered Fe(Al) solid solutions which were transformed to FeAl intermetallic after annealing. The effect of the milling time and annealing treatment on structural parameters, such as crystallite size, lattice parameter and lattice strain was evaluated by X-ray diffraction. Typically, these values were 15 nm, 2.92 A and 3.1% for the disordered Fe(Al) solid solution milled for 80 h and were 38.5 nm, 2.896 A and 1.2% for the FeAl intermetallic annealed at 700 o C, respectively.

Study of high-coercivity sintered NdFeB magnets

International Nuclear Information System (INIS)

Bai, G.; Gao, R.W.; Sun, Y.; Han, G.B.; Wang, B.

2007-01-01

Magnetic powders for sintered NdFeB magnets have been prepared by using an advanced processing method including strip casting, hydrogen decrepitation, jet milling and rubber isotropic press. The effects of Dy, Ga and Co addition on the microstructure and magnetic properties of sintered magnets have been investigated. By adopting a suitable component ratio and adjusting proper technological parameters, we have prepared high-coercivity sintered NdFeB magnets with hard magnetic properties of j H c =25.6 kOe, B r =13.2 kG and (BH) max =39.9 MGOe. The temperature coefficient of coercivity of the magnets (between 20 and 150 deg. C) is -0.53% deg. C. The magnetic properties at high temperature satisfy the needs of permanent magnet motors

The reduction of optimal heat treatment temperature and critical current density enhancement of ex situ processed MgB2 tapes using ball milled filling powder

Science.gov (United States)

Fujii, Hiroki; Iwanade, Akio; Kawada, Satoshi; Kitaguchi, Hitoshi

2018-01-01

The optimal heat treatment temperature (Topt) at which best performance in the critical current density (Jc) property at 4.2 K is obtained is influenced by the quality or reactivity of the filling powder in ex situ processed MgB2 tapes. Using a controlled fabrication process, the Topt decreases to 705-735 °C, which is lower than previously reported by more than 50 °C. The Topt decrease is effective to suppress both the decomposition of MgB2 and hence the formation of impurities such as MgB4, and the growth of crystallite size which decreases upper critical filed (Hc2). These bring about the Jc improvement and the Jc value at 4.2 K and 10 T reaches 250 A/mm2. The milling process also decreases the critical temperature (Tc) below 30 K. The milled powder is easily contaminated in air and thus, the Jc property of the contaminated tapes degrades severely. The contamination can raise the Topt by more than 50 °C, which is probably due to the increased sintering temperature required against contaminated surface layer around the grains acting as a barrier.

Detection of a milling-induced surface damage by the magnetic Barkhausen noise

Science.gov (United States)

Stupakov, A.; Neslušan, M.; Perevertov, O.

2016-07-01

The potential of the magnetic Barkhausen noise method for a non-destructive evaluation of the steel surface damage cased by milling was comprehensively investigated. A typical bearing steel was heat treated to three different hardnesses and then machined using the cutting tools with different degrees of the flank wear. The magnetic low-frequency measurements with a high reading depth were performed using a unique laboratory system providing a full control of the magnetization process. The high-frequency measurements were performed using a commercial Rollscan device. To study the induced magnetic anisotropy, the measurements were performed in two magnetization directions. In the feeding direction, the Barkhausen noise profiles showed a second high-field peak ascribed to an induced hardened surface layer, a so-called white layer. The most reliable results were obtained with the controlled waveform of the surface magnetic field measured directly by Hall sensors. In the perpendicular rotation direction, formation of the preferentially oriented matrix resulted in an enormously high Barkhausen noise activity. Based on these results, new magnetic parameters were proposed for the non-destructive evaluation of the white layer formation.

Mechanosynthesis, structural, thermal and magnetic characteristics of oleic acid coated Fe{sub 3}O{sub 4} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Marinca, T.F., E-mail: traian.marinca@stm.utcluj.ro [Materials Science and Engineering Department, Technical University of Cluj-Napoca, 103-105, Muncii Avenue, 400641 Cluj-Napoca (Romania); Chicinaş, H.F.; Neamţu, B.V. [Materials Science and Engineering Department, Technical University of Cluj-Napoca, 103-105, Muncii Avenue, 400641 Cluj-Napoca (Romania); Isnard, O. [Université Grenoble Alpes, Inst NEEL, F-38042 Grenoble (France); CNRS, Institut NEEL, 25 rue des Martyrs, BP166, F-38042 Grenoble (France); Pascuta, P. [Physics and Chemistry Department, Technical University of Cluj-Napoca, 103-105, Muncii Avenue, 400641 Cluj-Napoca (Romania); Lupu, N.; Stoian, G. [National Institute of Research & Development for Technical Physics, 47 Mangeron Boulevard, Iasi 700050 (Romania); Chicinaş, I. [Materials Science and Engineering Department, Technical University of Cluj-Napoca, 103-105, Muncii Avenue, 400641 Cluj-Napoca (Romania)

2016-03-01

Oleic acid coated iron ferrite-magnetite nanoparticles (Fe{sub 3}O{sub 4}) have been synthesized via a new combined route, ceramic method and subsequent wet mechanical milling, starting from a stoichiometric mixture of the easily accessible Fe and Fe{sub 2}O{sub 3} precursors. In the first step, the magnetite has been obtained in well crystallised state by heat treatment of precursor's mixture. In the second step, the as obtained magnetite powder has been wet milled in a high energy planetary ball mill using oleic acid as process control agent. Using the same conditions dry milled magnetite samples have been obtained for comparison. The as obtained powders have been characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), magnetic measurements M = f(H), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). According to XRD analysis two different processing mechanisms are observed for dry and wet milling modes. The magnetite mean crystallite size is 19 nm according to XRD after 240 min of wet mechanical milling. The High Resolution SEM confirmed that the powder consists in nanoparticles that have particles with the size up to 30 nm. The bond of the oleic acid to the magnetite nanoparticles has been observed by FTIR and DSC investigations. The presence of free and bonded oleic acid is revealed and the free oleic acid can be removed controlled by heat treatment. The magnetisation of the milled samples is lower as compared to the magnetisation of the un-milled sample due to several causes such as disordered structure, finite size effect and powder contamination. A powder contamination with iron occurs during milling and this leads to the formation of a wüstite-FeO phase for the dry milled samples. In the case of the wet milled samples, due to an oleic acid layer the FeO phase formation is prevented. - Highlights: • Oleic acid coated magnetite has been synthetized by a new combined route. • XRD

Effect of composition and heat treatment on the phase formation of mechanically alloyed Cr-B and Mo-B powders

International Nuclear Information System (INIS)

Wu, H M; Hu, C J; Pai, K Y

2009-01-01

Blended elemental Cr-B and Mo-B powders in atomic ratio of 67:33, 50:50, and 20:80 were subjected to mechanical alloying up to 60 h and subsequent heat treatment to investigate effect of composition and heat treatment on the phase formation of Cr-B and Mo-B powders. It was studied by X-ray diffraction and differential thermal analysis. Mechanical alloying these powder mixtures for 60 h leads essentially to a amorphous structure except for the Mo 20 B 80 powder, which creates a partially amorphous MoB 4 structure. Annealing at lower temperatures relieves the strains cumulative in the milled powders and creates no new phase. The structures obtained after annealing the milled powders at higher temperature vary and depend on the overall composition of the powder mixtures. Annealing the milled Mo-B powders having greater Mo content ends up with a dissociation reaction at higher temperature.

Mechanically Induced Graphite-Nanodiamonds-Phase Transformations During High-Energy Ball Milling

Science.gov (United States)

El-Eskandarany, M. Sherif

2017-05-01

Due to their unusual mechanical, chemical, physical, optical, and biological properties, nearly spherical-like nanodiamonds have received much attention as desirable advanced nanomaterials for use in a wide spectrum of applications. Although, nanodiamonds can be successfully synthesized by several approaches, applications of high temperature and/or high pressure may restrict the real applications of such strategic nanomaterials. Distinct from the current preparation approaches used for nanodiamonds preparation, here we show a new process for preparing ultrafine nanodiamonds (3-5 nm) embedded in a homogeneous amorphous-carbon matrix. Our process started from high-energy ball milling of commercial graphite powders at ambient temperature under normal atmospheric helium gas pressure. The results have demonstrated graphite-single wall carbon nanotubes-amorphous-carbon-nanodiamonds phase transformations carried out through three subsequent stages of ball milling. Based on XRD and RAMAN analyses, the percentage of nanodiamond phase + C60 (crystalline phase) produced by ball milling was approximately 81%, while the amorphous phase amount was 19%. The pressure generated on the powder together the with temperature increase upon the ball-powder-ball collision is responsible for the phase transformations occurring in graphite powders.

Hollow crystalline straws of diclofenac for high-dose and carrier-free dry powder inhaler formulations.

Science.gov (United States)

Yazdi, Ashkan K; Smyth, Hugh D C

2016-04-11

To crystallize diclofenac (DF) from diclofenac sodium (DFNa), to micronize DF and DFNa, and to evaluate in vitro aerodynamic performance of the jet-milled formulations From the acidic titration of aqueous DFNa, DF crystals were formed and were identified using thermal analysis, spectroscopy, and X-ray powder diffraction. Following the micronization of the DF and DFNa powders, the recovered samples were imaged, and their particle size distributions were evaluated. Samples before and after jet millings were characterized, and in vitro aerodynamic performance testing was performed on the DF sample before jet milling and the DF and DFNa samples following jet milling. Hollow needles of DF were precipitated. With similar particle size distributions, the jet-milled DFNa sample from the collection bag, and the DF sample from the cyclone were used for further characterization. Despite different deposition patterns in the Next Generation Impactor, the DF hollow needles had a comparable respirable fraction percentage to the jet-milled DF and DFNa particles. However, the jet-milled DF formulation had the best in vitro aerodynamic performance. Hollow, crystalline needles of DF were formed and possessed promising aerosol performance in comparison with the jet-milled powders. Copyright © 2016 Elsevier B.V. All rights reserved.

Mechanical alloying of Hf and Fe powders

International Nuclear Information System (INIS)

Mendoza Zelis, L.; Crespo, E.; Creus, M.; Damonte, L.C.; Sanchez, F.H.; Punte, G.

1994-01-01

Pure crystalline Hf and Fe powders were mixed and milled under an argon atmosphere. The evolution of the system with milling time was followed with Moessbauer effect spectroscopy and X-ray diffraction. The results indicate that in the first stages an amorphous Fe-rich alloy was gradually formed together with a solid solution of Hf in Fe beyond the solubility limit. (orig.)

Effect of cryogenic milling on Al7075 prepared by spark plasma sintering method.

Czech Academy of Sciences Publication Activity Database

Lukáč, František; Chráska, Tomáš; Molnárová, O.; Málek, P.; Cinert, Jakub

2017-01-01

Roč. 32, S1 (2017), S221-S224 ISSN 0885-7156. [European Powder Diffraction Conference (EPDIC) /15./. Bari, 12.06.2016-15.06.2016] R&D Projects: GA ČR(CZ) GA15-15609S Institutional support: RVO:61389021 Keywords : Intermetallic precipitates * cryogenic milling * powder metallurgy * ultrafine-grained materials * Al7075 alloy Subject RIV: JG - Metallurgy OBOR OECD: Materials engineering Impact factor: 0.674, year: 2016 https://www.cambridge.org/core/journals/powder-diffraction/ article /effect-of-cryogenic-milling-on-al7075-prepared-by-spark-plasma-sintering-method/17E9F722BAFD428BA7310194FEE551C6

Mechanochemical preparation of nanocrystalline TiO2 powders and their behavior at high temperatures

International Nuclear Information System (INIS)

Gajovic, A.; Furic, K.; Tomasic, N.; Popovic, S.; Skoko, Z.; Music, S.

2005-01-01

Nanocrystalline TiO 2 powders were prepared by high-energy ball-milling using zirconia vial and balls. The changes of microstructure caused by material processing were studied using Raman spectroscopy, X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and selected area electron diffraction (SAED). The milling of the starting TiO 2 powder (anatase + rutile in traces) induced phase transitions to high-pressure polymorph, TiO 2 II, and rutile. We found that the phase transition to TiO 2 II was initiated at the surface of the small particles, while transition to rutile started in their center. Changes in crystallite size during milling process were obtained by the Scherrer method, while the particle size changes were monitored by TEM. The kinetics of phase changes, a decrease in crystallite/particle size, as well as zirconia contamination depended on the powder-to-ball weight ratio. The starting powder and some selected ball-milled samples were investigated in situ by Raman spectroscopy and XRD at high temperatures (up to 1300 deg. C) to examine their behavior during the sintering process. A difference in the results obtained by these two techniques was explained in frame of basic physical properties characterizing both methods. The morphology of the final sinters was monitored by scanning electron microscopy (SEM)

On the cooling rate of strip cast ingots for sintered NdFeB magnets

Energy Technology Data Exchange (ETDEWEB)

Yu, L.Q. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Yan, M. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China)]. E-mail: mse_yanmi@dial.zju.edu.cn; Wu, J.M. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Luo, W. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Cui, X.G. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Ying, H.G. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China)

2007-04-30

Effects of the cooling rate of strip cast ingots on magnetic properties of sintered NdFeB magnets were studied. It is found that the magnetic properties greatly depend on wheel speed due to different alloy microstructures, which affect readily the particle size distribution of powders obtained after the subsequent jet milling. At higher cooling rate, interlamellar spacing between Nd-rich platelets of the alloy was small, resulting in a lower saturated magnetization due to increased amounts of small particles after jet milling. With further decreasing cooling rate, the resultant larger interlamellar spacing led to too large particle sizes as well as a more irregular shape; thus deteriorated the magnetic properties of the final magnet. A model was developed to disclose the effects of particle sizes on the magnetic alignment process. In the current investigation, optimum magnetic properties of the final magnets were obtained with a cooling rate of 2.6 m/s for preparing the strip. The magnets made by conventionally cast ingot technique exhibited the lowest magnetic properties because of the slowest cooling rate.

Study of soft magnetic iron cobalt based alloys processed by powder injection molding

International Nuclear Information System (INIS)

Silva, Aline; Lozano, Jaime A.; Machado, Ricardo; Escobar, Jairo A.; Wendhausen, Paulo A.P.

2008-01-01

As a near net shape process, powder injection molding (PIM) opens new possibilities to process Fe-Co alloys for magnetic applications. Due to the fact that PIM does not involve plastic deformation of the material during processing, we envisioned the possibility of eliminating vanadium (V), which is generally added to Fe-Co alloys to improve the ductility in order to enable its further shaping by conventional processes such as forging and cold rolling. In our investigation we have found out two main futures related to the elimination of V, which lead to a cost-benefit gain in manufacturing small magnetic components where high-saturation induction is needed at low frequencies. Firstly, the elimination of V enables the achievement of much better magnetic properties when alloys are processed by PIM. Secondly, a lower sintering temperature can be used when the alloy is processed starting with elemental Fe and Co powders without the addition of V

Microstructural evolution of nanostructured Ti0.9Al0.1N prepared by reactive ball-milling

International Nuclear Information System (INIS)

Bhaskar, U.K.; Bid, S.; Pradhan, S.K.

2011-01-01

Research highlights: → Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N powder has been prepared by ball-milling the 0.9 mol fraction of α-Ti (hcp) and 0.1 mol fraction of aluminum (fcc) powders under N 2 at room temperature. Initially, α-Ti phase partially transformed to the transient β-Ti phase and Ti 0.9 Al 0.1 N (fcc) phase is noticed to form after 3 h of milling. Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N phase is formed after 7 h of milling. The main features which are observed in the present study are stated below: 1.During ball-milling of α-Ti, the α-Ti phase partially converted to transient cubic β-Ti phase within 1 h of milling. 2.Ti 0.9 Al 0.1 N (fcc) phase is noticed to form after 3 h of milling. Complete formation of Ti 0.9 Al 0.1 N (fcc) is obtained at 7 h of milling which is lesser than complete formation time (9 h) of TiN. Doping Al atoms accelerates the formation of (TiAl)N phase. 3.The particle size of Ti 0.9 Al 0.1 N decrease rapidly up to 3 h and then increase slightly due to agglomeration effect. 4.The particle size of Ti 0.9 Al 0.1 N estimated from X-ray is in good agreement with that measured from HRTEM. - Abstract: Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N powder has been prepared by ball-milling the α-Ti (hcp) and aluminum (fcc) powders under N 2 at room temperature. Initially, α-Ti phase partially transformed to the transient cubic β-Ti phase and Ti 0.9 Al 0.1 N (fcc) phase is noticed to form after 3 h of milling. Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N phase is formed after 7 h of milling. After 1 h of milling, all Al atoms are diffused into the α-Ti matrix. The transient β-Ti phase is noticed to form after 1 h of milling and disappears completely after 7 h of milling. Microstructure characterization of unmilled and ball-milled powders by analyzing XRD patterns employing the Rietveld structure refinement reveals the inclusion of Al and nitrogen atoms into the Ti lattice on the way to formation of Ti 0.9 Al 0.1 N

Magnetic interactions in high-energy ball-milled NiZnFe2O4/SiO2 composites

International Nuclear Information System (INIS)

Pozo Lopez, G.; Silvetti, S.P.; Urreta, S.E.; Cabanillas, E.D.

2007-01-01

Composites Ni 0.5 Zn 0.5 Fe 2 O 4 /SiO 2 are obtained after high-energy ball milling precursor oxides, in stoichiometric proportions, for 200 h at room temperature and further isothermal annealing for 1 h at 1273 K, under air and argon atmosphere, respectively. After 200 h grinding, a complex microstructure develops with small hematite crystals mixed with SiO 2 and remanent NiO and ZnO particles, and very small NiZn ferrite clusters, reaching a mean size of ∼9 nm. The high temperature treatments remove the hematite grains from the powder and promote the growth of NiZn ferrite grains to reach mean sizes nearly ∼20 nm. For treatments in oxidizing atmospheres, the major phases are SiO 2 and NiZn ferrite, while for annealing in Ar a new phase appears, fayalite, which is paramagnetic at room temperature. The M-H loops are all well described by the sum of a ferromagnetic and a superparamagnetic-like contribution. The observed properties are interpreted considering the different magnetic phases obtained, their crystal sizes and their mutual interactions

Effect of milling time on the structure, micro-hardness, and thermal behavior of amorphous/nanocrystalline TiNiCu shape memory alloys developed by mechanical alloying

International Nuclear Information System (INIS)

Alijani, Fatemeh; Amini, Rasool; Ghaffari, Mohammad; Alizadeh, Morteza; Okyay, Ali Kemal

2014-01-01

Highlights: • Potential to produce B1′ (thermal- and stress-induced) and B2 was established. • Martensitic transformation occurred without the formation of intermediate R-phase. • Formation of unwanted intermetallics during heating was hindered by milling. • During milling, microhardness was increased, then reduced, and afterward re-increased. • By milling evolution, thermal crystallization steps changed from 3 to 2. - Abstract: In the present paper, the effect of milling process on the chemical composition, structure, microhardness, and thermal behavior of Ti–41Ni–9Cu compounds developed by mechanical alloying was evaluated. The structural characteristic of the alloyed powders was evaluated by X-ray diffraction (XRD). The chemical composition homogeneity and the powder morphology and size were studied by scanning electron microscopy coupled with electron dispersive X-ray spectroscopy. Moreover, the Vickers micro-indentation hardness of the powders milled for different milling times was determined. Finally, the thermal behavior of the as-milled powders was studied by differential scanning calorimetery. According to the results, at the initial stages of milling (typically 0–12 h), the structure consisted of a Ni solid solution and amorphous phase, and by the milling evolution, nanocrystalline martensite (B19′) and austenite (B2) phases were initially formed from the initial materials and then from the amorphous phase. It was found that by the milling development, the composition uniformity is increased, the inter-layer thickness is reduced, and the powders microhardness is initially increased, then reduced, and afterward re-increased. It was also realized that the thermal behavior of the alloyed powders and the structure of heat treated samples is considerably affected by the milling time

Synthesis of LiBOB Fine Powder to Increase Solubility

Directory of Open Access Journals (Sweden)

Etty Marti Wigayati

2017-04-01

Full Text Available Lithium bis (oxalate borate or LiBOB compound has captured interest of researchers, because it is potentially viable to be used as electrolyte salt in lithium-ion battery system. This compound is easy to synthesize and considered to be more environmentally friendly compared to conventional electrolyte salt because LiBOB does not contain halogen element. This research focused on the synthesis of LiBOB fine powder, which main purpose is improving LiBOB salt solubility in liquid electrolyte solution. This will aid the ion transfer between electrodes which in turn will increase the electrolyte performance. Solid state reaction was employed in this experiment. Synthesis of LiBOB compound was performed by reacting oxalic acid dihydrate, lithium hydroxide monohydrate, and boric acid. The resulting powder was then processed into fine powder using ball milling technique with varying milling time (0, 6, 10, and 13 hour. Microstructure of the sample was then analyzed to obtain information regarding phase formation, functional groups, grain surface morphology, surface area, pore volume, solubility, and ionic conductivity. The analysis shown that LiBOB and LiBOB hydrate phase was formed during the reaction, there was no changed in existing phase during milling process, crystallinity index was shifted to lower value but there was no difference in functional groups. Highest value in surface area was found to be 83.11 m2/g, with pore volume of 1.21311e+02 A at 10 hours milling. Smaller powder size resulted in higher solubility, unfortunately the ionic conductivity was found to be decreased.

Structural, optical, and magnetic properties of Fe doped In{sub 2}O{sub 3} powders

Energy Technology Data Exchange (ETDEWEB)

Krishna, N. Sai [Thin Films Laboratory, School of Advanced Sciences, VIT University, Vellore 632 014, Tamilnadu (India); Kaleemulla, S., E-mail: skaleemulla@gmail.com [Thin Films Laboratory, School of Advanced Sciences, VIT University, Vellore 632 014, Tamilnadu (India); Amarendra, G. [Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, Tamilnadu (India); UGC-DAE-CSR, Kalpakkam Node, Kokilamedu 603 104, Tamilnadu (India); Rao, N. Madhusudhana; Krishnamoorthi, C.; Kuppan, M.; Begam, M. Rigana [Thin Films Laboratory, School of Advanced Sciences, VIT University, Vellore 632 014, Tamilnadu (India); Reddy, D. Sreekantha [Department of Physics and Sungkyunkwan Advanced Institute of Nanotechnology (SAINT), Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Omkaram, I. [Department of Electronics and Radio Engineering, Kyung Hee University, Yongin-si, Gyeonggi-do 446-701 (Korea, Republic of)

2015-01-15

Highlights: • Synthesis of Fe doped In{sub 2}O{sub 3} powders using a solid state reaction. • Characterization of the samples using XRD, UV–vis-NIR, FT-IR, and VSM. • All Fe doped In{sub 2}O{sub 3} powders exhibited the cubic structure of In{sub 2}O{sub 3}. • All the Fe doped In{sub 2}O{sub 3} samples exhibited room temperature ferromagnetism. - Abstract: Iron doped indium oxide dilute magnetic semiconductor (In{sub 1−x}Fe{sub x}){sub 2}O{sub 3} (x = 0.00, 0.03, 0.05, and 0.07) powders were synthesized by standard solid state reaction method followed by vacuum annealing. The effect of Fe concentration on structural, optical, and magnetic properties of the (In{sub 1−x}Fe{sub x}){sub 2}O{sub 3} powders have been systematically studied. X-ray diffraction patterns confirmed the polycrystalline cubic structure of all the samples. An optical band gap increases from 3.12 eV to 3.16 eV while Fe concentration varying from 0.03 to 0.07. Magnetic studies reveal that virgin/undoped In{sub 2}O{sub 3} is diamagnetic. However, all the Fe-doped In{sub 2}O{sub 3} samples are ferromagnetic. The saturation magnetization (M{sub s}) of ferromagnetic (In{sub 1−x}Fe{sub x}){sub 2}O{sub 3} (x = 0.03, 0.05, and 0.07) samples increases from 11.56 memu/g to 148.64 memu/g with x = 0.03–0.07. The observed ferromagnetism in these samples was attributed to magnetic nature of the dopant (Fe) as well as defects created in the samples during vacuum annealing.

HDDR in Sm-Co alloys - a new method for magnetic hardening of Sm-Co permanent magnets

Energy Technology Data Exchange (ETDEWEB)

Kubis, M.; Handstein, A.; Gebel, B.; Mueller, K.-H.; Schultz, L. [Institut fuer Festkoerper- und Werkstofforschung Dresden e.V. (Germany). Inst. fuer Metallische Werkstoffe; Gutfleisch, O. [Institut fuer Festkoerper- und Werkstofforschung Dresden e.V. (Germany). Inst. fuer Metallische Werkstoffe]|[Birmingham Univ. (United Kingdom). School of Metallurgy and Materials

1998-07-01

Investigations on the hydrogen absorption behavior of different Sm-Co alloys with 1:5 and 2:17 structure by differential scanning calorimetry (DSC) at enhanced hydrogen pressures between 1 MPa and 7 MPa indicated different hydrogen absorption events. X-ray diffraction (XRD) studies and microstructural investigations showed clearly the disproportionation of the Sm-Co phases into Sm hydride and Co or Co-rich phases for hydrogen pressures above 0.5 MPa. The favourable effect of high hydrogen pressures can be explained in terms of a decrease of the free enthalpy of the samarium hydride for increasing hydrogen pressures. Additionally, Sm-Co alloys of both types were reactively milled under hydrogen at enhanced temperatures. The reactively milled powders showed again the products of the disproportionation reaction. A recombination of Sm-Co phases by removing the hydrogen in a second heat treatment was successful for both methods. Investigations of the magnetic properties showed coercivities {mu}{sub OJ}H{sub C} of up to 2.1 T for high pressure HDDR powders of SmCo{sub 5} material, demonstrating clearly the positive effect of the hydrogen treatment on the coercivity. The reactively milled powders showed for recombination temperatures {<=}700 C a remanence enhancement which could be attributed to the exchange coupling of the nanoscaled grains. A maximum coercivity {mu}{sub OJ}H{sub C} of 3.7 T was achieved for SmCo{sub 5} and a maximum energy product (BH){sub max} of 82 kJ/m{sup 3} was measured for an Sm-rich Sm{sub 2}Co{sub 17} sample. (orig.)

HDDR in Sm-Co alloys - a new method for magnetic hardening of Sm-Co permanent magnets

International Nuclear Information System (INIS)

Kubis, M.; Handstein, A.; Gebel, B.; Mueller, K.-H.; Schultz, L.; Gutfleisch, O.; Birmingham Univ.

1998-01-01

Investigations on the hydrogen absorption behavior of different Sm-Co alloys with 1:5 and 2:17 structure by differential scanning calorimetry (DSC) at enhanced hydrogen pressures between 1 MPa and 7 MPa indicated different hydrogen absorption events. X-ray diffraction (XRD) studies and microstructural investigations showed clearly the disproportionation of the Sm-Co phases into Sm hydride and Co or Co-rich phases for hydrogen pressures above 0.5 MPa. The favourable effect of high hydrogen pressures can be explained in terms of a decrease of the free enthalpy of the samarium hydride for increasing hydrogen pressures. Additionally, Sm-Co alloys of both types were reactively milled under hydrogen at enhanced temperatures. The reactively milled powders showed again the products of the disproportionation reaction. A recombination of Sm-Co phases by removing the hydrogen in a second heat treatment was successful for both methods. Investigations of the magnetic properties showed coercivities μ OJ H C of up to 2.1 T for high pressure HDDR powders of SmCo 5 material, demonstrating clearly the positive effect of the hydrogen treatment on the coercivity. The reactively milled powders showed for recombination temperatures ≤700 C a remanence enhancement which could be attributed to the exchange coupling of the nanoscaled grains. A maximum coercivity μ OJ H C of 3.7 T was achieved for SmCo 5 and a maximum energy product (BH) max of 82 kJ/m 3 was measured for an Sm-rich Sm 2 Co 17 sample. (orig.)

Nanocrystalline NdFeB magnet prepared by mechanically activated disproportionation and desorption-recombination in-situ sintering

International Nuclear Information System (INIS)

Xiaoya, Liu; Yuping, Li; Lianxi, Hu

2013-01-01

The process of mechanically activated disproportionation and desorption-recombination in-situ sintering was proposed to synthesize highly densified nanocrystalline NdFeB magnet, and its validity was demonstrated by experimental investigation with the use of a Nd 16 Fe 76 B 8 (atomic ratio) alloy. Firstly, the as-cast alloy was disproportionated by mechanical milling in hydrogen, with the starting micron-sized Nd 2 Fe 14 B phase decomposed into an intimate mixture of nano-structured NdH 2.7 , Fe 2 B and α-Fe phases. The as-disproportionated alloy powders were compacted by cold pressing and then subjected to desorption-recombination in-situ sintering. The microstructure of both the as-disproportionated and the subsequently sintered samples was characterized by X-ray diffraction and electron transmission microscopy, respectively. The magnetic properties of the sintered samples were measured by using vibrating sample magnetometer. The results showed that, by vacuum sintering, not only was the powder compact consolidated, but also the as-disproportionated microstucture transformed into nanocrystalline Nd 2 Fe 14 B phase via the well-known desorption-recombination reaction, thus giving rise to nanocrystalline NdFeB magnet. In the present study, the optimal sintering parameters were found to be 780 °C×30 min. In this case, the coercivity, the remanence, and maximum energy product of the magnet sample achieved 0.8 T, 635.3 kA/m, and 106.3 kJ/m 3 , respectively. - Highlights: ► Nano-structured disproportionated NdFeB alloy powders by mechanical milling in hydrogen. ► Highly densified green magnet compact by cold pressing of as-disproportionated NdFeB alloy powders. ► Nanocrystalline NdFeB magnets by desorption-recombination in-situ sintering under vacuum. ► Magnetic properties significantly improved by relative density enhancement and nanocrystallization of Nd 2 Fe 14 B phase. ► The effects of sintering parameters on magnetic properties and the underlying

Magnetic features of Fe-Cr-Co alloys with tailoring chromium content fabricated by spark plasma sintering

International Nuclear Information System (INIS)

Rastabi, Reza Amini; Ghasemi, Ali; Tavoosi, Majid; Ramazani, Mazaher

2017-01-01

Structural and magnetic characterization of Fe-Cr-Co alloys during milling, annealing and consolidation processes was the goal of this study. In this regards, different powder mixtures of Fe 80−x Cr x Co 20 (15≤x≤35) were mechanically milled in a planetary ball mill and then were consolidated by spark plasma sintering (SPS). The produced samples were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). According to achieved results, the structure of as-milled samples in different compositions consists of single α phase solid solution with coercivity and saturation of magnetization in the range of 110–200 Oe and 150–220 emu/g, respectively. The magnetic properties of consolidated samples depend on the kinds of formed precipitates in microstructure and the maximum values of coercive force and saturation of magnetization obtained in Fe 55 Cr 25 Co 20 magnetic (with single α phase) alloy were 107 Oe and Ms 172 emu/g, respectively. In fact, the formation of non-magnetic σ and γ phases has a destructive effect on magnetic properties of consolidated samples with higher Cr content. Since such magnet requires less cobalt, and contains similar magnetic feature with superior ductility compare to the AlNiCo 5, it could be considered as a promising candidate for employing instead of AlNiCo 5. - Highlights: • Milled samples consist of single phase α-solid solution. • Saturation of magnetization of Fe 65 Cr 15 Co 20 reached to 172 emu/g. • Fe 65 Cr 15 Co 20 alloy is the suitable composition fabricated by SPS.

Effect of Mechanical Activation on the In Situ Formation of TiB2 Particulates in the Powder Mixture of TiH2 and FeB

Directory of Open Access Journals (Sweden)

Huynh X.-K.

2017-06-01

Full Text Available The in situ formation of TiB2 particulates via an interface reaction between Ti and FeB powders was studied. The effects of mechanical activation by high-energy milling on the decomposition of TiH2 and the interface reactions between Ti and FeB powders to form TiB2 were investigated. Powder mixtures were fabricated using planetary ball-milling under various milling conditions. The specific ball-milling energy was calculated from the measured electrical power consumption during milling process. High specific milling energy (152.6 kJ/g resulted in a size reduction and homogeneous dispersion of constituent powders. This resulted in a decrease in the decomposition temperature of TiH2 and an increase in the formation reaction of TiB2 particulates in the Fe matrix, resulting in a homogeneous microstructure of nanoscale TiB2 evenly distributed within the Fe matrix. In contrast, the powder mixture milled with low specific milling energy (36.5 kJ/g showed an inhomogeneous microstructure composed of relatively large Fe-Fe2B particles surrounded by a thin layer of Fe-TiB2 within a finely dispersed Fe-TiB2 matrix region.

Mechanochemical synthesis of nanocrystalline Fe and Fe–B magnetic alloys

International Nuclear Information System (INIS)

Mohammadi, Majid; Ghasemi, Ali; Tavoosi, Majid

2016-01-01

Mechanochemical synthesis and magnetic characterization of nanocrystalline Fe and Fe–B magnetic alloys was the goal of this study. In this regard, different Fe_2O_3–B_2O_3 powder mixtures with sufficient amount of CaH_2 were milled in a planetary ball mill in order to produce nanocrystalline Fe, Fe_9_5B_5 and Fe_8_5B_1_5 alloys. The produced samples were characterized using X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). The results showed that, nanocrystalline Fe, Fe_9_5B_5 and Fe_8_5B_1_5 alloys can be successfully synthesized by the reduction reaction of Fe_2O_3 and B_2O_3 with CaH_2 during mechanical alloying. The structure of produced Fe_9_5B_5 and Fe_8_5B_1_5 alloys was a combination of Fe and Fe_2B phases with average crystallite sizes of about 15 and 10 nm, respectively. The produced nanocrystalline alloys exhibited soft magnetic properties with the coercivity and saturation of magnetization in the range of 170–240 Oe and 9–28 emu/g, respectively. Increasing the boron content has a destructive effect on soft magnetic properties of Fe–B alloys. - Highlights: • We study the mechanochemical synthesis of nanocrystalline boron, Fe and Fe–B alloys. • We study the reduction reaction of B_2O_3–CaH_2 during milling. • We study the reduction reaction of Fe_2O_3–CaH_2 during milling. • We study the reduction reaction of Fe_2O_3–B_2O_3–CaH_2 during milling. • We study the effect of B on magnetic properties of nanocrystalline Fe–B alloys.

Study of the microstructural and mechanical properties of titanium-niobium-zirconium based alloys processed with hydrogen and powder metallurgy for use in dental implants

International Nuclear Information System (INIS)

Duvaizem, Jose Helio

2009-01-01

Hydrogen has been used as pulverization agent in alloys based on rare earth and transition metals due to its extremely high diffusion rate even on low temperatures. Such materials are used on hydrogen storage dispositives, generation of electricity or magnetic fields, and are produced by a process which the first step is the transformation of the alloy in fine powder by miling. Besides those, hydrogenium is also being used to obtain alloys based on titanium - niobium - zirconium in the pulverization. Powder metallurgy is utilized on the production of these alloys, making it possible to obtain structures with porous surface as result, requirement for its application as biomaterials. Other advantages of powder metallurgy usage include better surface finish and better microstructural homogeneity. In this work samples were prepared in the Ti-13Nb-13Zr composition. The hydrogenation was performed at 700 degree C, 600 degree C, and 500 degree C for titanium, niobium and zirconium respectively. After hydrogenation, the milling stage was carried out on high energy planetary ball milling with 200rpm during 90 minutes, and also in conventional ball milling for 30 hours. Samples were pressed in uniaxial press, followed by isostatic cold press, and then sintered at 1150 degree C for 7-13 hours. Microstructural properties of the samples were characterized by scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and x-ray diffraction. Mechanical and structural properties determined were density, microhardness and moduli of elasticity. The sample sintered at 1150 degree C for 7h, hydrogenated using 10.000 mbar and produced by milling on high energy planetary ball milling presented the best mechanical properties and microstructural homogeneity. (author)

Effects of Temperature variations on the Super Fine Powderization of Korean Cultivated Wild Ginseng

Directory of Open Access Journals (Sweden)

Jin Ho Kim

2006-12-01

Full Text Available Objectives : The aim of this study was to find optimal conditions for producing red ginseng from cultivated wild ginseng using the Turbo Mill. Methods : Characteristics of powdered cultivated wild ginseng based on various temperature settings of the Turbo Mill were observed, and changes in the content was measured by HPLC for various ginsenosides. Results : 1. The diameter of cultivated wild ginseng powder ground by the Turbo Mill was around 10㎛. 2. As the temperature rose, presusre, Specific Mechanical Energy(SME, and density decreased, whileas Water Solubility Index(WSI increased. 3. As the temperature rose, super fine powder showed tendency to turn into dark brown. 4. Measuring content changes by HPLC, there was no detection of ginsenoside Rg3 and ginsenosideRg1, Rb1, and Rh2 concentrations decreased with increase in temperature. Conclusions : Super fine powder of cultivated wild ginseng produced by the Turbo Mill promotes easy absorption of effective ingredients by breaking the cell walls. Using this mechanism to produce red ginseng from cultivated wild ginseng, it yielded less than satisfactory results under the current experiment setup. Furtherresearches are needed to verify more suitable condition for the production of red ginseng.

Study of high-coercivity sintered NdFeB magnets

Energy Technology Data Exchange (ETDEWEB)

Bai, G. [School of Physics and Microelectronics, Shandong University, Jinan, 250100 (China); Department of Mathematics and Physics, Xi' an Institute of Technology, Xi' an, 710032 (China); Gao, R.W. [School of Physics and Microelectronics, Shandong University, Jinan, 250100 (China)]. E-mail: gaorwbox@sdu.edu.cn; Sun, Y. [School of Physics and Microelectronics, Shandong University, Jinan, 250100 (China); Han, G.B. [School of Physics and Microelectronics, Shandong University, Jinan, 250100 (China); Wang, B. [School of Physics and Microelectronics, Shandong University, Jinan, 250100 (China); Baotou Rare Earth Research Institute, Batou 014030 (China)

2007-01-15

Magnetic powders for sintered NdFeB magnets have been prepared by using an advanced processing method including strip casting, hydrogen decrepitation, jet milling and rubber isotropic press. The effects of Dy, Ga and Co addition on the microstructure and magnetic properties of sintered magnets have been investigated. By adopting a suitable component ratio and adjusting proper technological parameters, we have prepared high-coercivity sintered NdFeB magnets with hard magnetic properties of {sub j} H {sub c}=25.6 kOe, B {sub r}=13.2 kG and (BH){sub max}=39.9 MGOe. The temperature coefficient of coercivity of the magnets (between 20 and 150 deg. C) is -0.53% deg. C. The magnetic properties at high temperature satisfy the needs of permanent magnet motors.

Effect of processing parameters on the magnetic properties and microstructures of molybdenum permalloy compacts made by powder metallurgy

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhangming; Xu, Wei; Guo, Ting; Jiang, Yinzhu; Yan, Mi, E-mail: mse_yanmi@zju.edu.cn

2014-05-01

Highlights: • Effect of processing parameters on the properties of MP powder cores was studied. • Effective magnetic permeability was enhanced from 45 to 160 after annealing. • A core loss of 780 mw/cm{sup 3} (100 kHz, 100 mT) was obtained. - Abstract: Effects of compaction and annealing process on the magnetic properties and microstructures of molybdenum permalloy (MP) powder cores have been investigated. MP compacts, with density as high as 92% of the theoretical value, were obtained under 1800 MPa compaction pressure. The MP powder cores show an enhanced effective magnetic permeability of 160 after post-annealing at 690 °C, which is attributed to the relief of internal stress rather than the phase transformation evidenced by the XRD analysis. However, higher annealing temperature destroys the insulating layer, resulting in the drop of the electrical resistivity, the effective magnetic permeability as well as the frequency stability. The results show that the samples compacted at 1800 MPa and annealed at 690 °C exhibit excellent magnetic properties, with core loss of 780 mw/cm{sup 3} (100 kHz, 100 mT) and effective magnetic permeability of 160 whose frequency stability is up to 1 MHz.

Effect of milling time on microstructure and properties of Nano-titanium polymer by high-energy ball milling

Science.gov (United States)

Wang, Bo; Wei, Shicheng; Wang, Yujiang; Liang, Yi; Guo, Lei; Xue, Junfeng; Pan, Fusheng; Tang, Aitao; Chen, Xianhua; Xu, Binshi

2018-03-01

Nano-titanium (Nano-Ti) was prepared by high-energy ball milling from pure Ti power and grinding agents (Epoxy resin) at room temperature. The effect of milling time on structure and properties of Nano-Ti polymer were investigated systematically. The results show that high-energy ball milling is an effective way to produce Nano-Ti polymer. The dispersion stability and compatibility between Ti power and grinding agents are improved by prolonging the milling time at a certain degree, that is to say, the optimization milling time is 240 min. The particle size of Ti powder and the diffraction peaks intensity of Ti decrease obviously as the milling time increases due to the compression stress, shear friction and other mechanical forces are formed during ball milling. FT-IR result displays that the wavenumber of all the bands move to lower wavenumber after ball milling, and the epoxy ring is open. The system internal energy rises owing to the broken epoxy group and much more Nano-Ti is formed to promote the grafting reaction between Nano-Ti and epoxy resin. The results from TEM and XPS also prove that. And the grafting ration is maximum as the milling time is 240 min, the mass loss ratio is 17.53%.

Microstructural and electrical changes in nickel manganite powder induced by mechanical activation

International Nuclear Information System (INIS)

Savic, S.M.; Mancic, L.; Vojisavljevic, K.; Stojanovic, G.; Brankovic, Z.; Aleksic, O.S.; Brankovic, G.

2011-01-01

Highlights: → The influence of mechanical activation on microstructure evolution in the nickel manganite powder was investigated as well as electrical properties of the sintered samples. → Structural refinement obtained by Topas-Academic software based on Rietveld analysis showed that the milling process remarkably changed the powder morphology and microstructure. → SEM studies of sintered samples also revealed the strong influence of milling time on ceramics density (increases with milling time). → The electrical properties of ceramic samples are clearly conditioned by terms of synthesis, in our case the time of mechanical activation. → The highest density and higher values of dielectric constant were achieved at the sample activated for 45 min. -- Abstract: Nickel manganite powder synthesized by calcination of a stoichiometric mixture of manganese and nickel oxide was additionally mechanically activated in a high energy planetary ball mill for 5-60 min in order to obtain a pure NiMn 2 O 4 phase. The as-prepared powders were uniaxially pressed into disc shape pellets and then sintered for 60 min at 1200 o C. Changes in the particle morphology induced by mechanical activation were monitored using scanning electron microscopy, while changes in powder structural characteristics were followed using X-ray powder diffraction. The ac impedance spectroscopy was performed on sintered nickel manganite samples at 25 o C, 50 o C and 80 o C. It was shown that mechanical activation intensifies transport processes causing a decrease in the average crystallites size, while longer activation times can lead to the formation of aggregates, defects and increase of lattice microstrains. The observed changes in microstructures were correlated with measured electrical properties in order to define optimal processing conditions.

Multi-layered electroless Ni-P coatings on powder-sintered Nd-Fe-B permanent magnet

International Nuclear Information System (INIS)

Chen Zhong; Ng, Alice; Yi Jianzhang; Chen Xingfu

2006-01-01

This paper has shown a successful protective coating scheme for powder-sintered Nd-Fe-B permanent magnet using multi-layered electroless nickel (EN) deposition. A low-phosphorus nickel layer is plated with an alkaline EN solution first, followed by a high-phosphorus nickel layer plated with an acidic solution. An additional topcoat by medium-phosphorus nickel on the high-phosphorus coating is also explored. It is shown that the high-phosphorus nickel layer coated in acidic solution provides the best corrosion protection because of its dense amorphous structure. The medium phosphorus topcoat is also dense and is able to provide reasonable corrosion resistance. The low-phosphorus layer itself does not have enough corrosion resistance; its main role is to provide an intermediate coating on the powder-sintered magnet. X-ray diffraction measurement shows that the low-phosphorus coating consists of nano-crystallines, and the high- and the medium-phosphorus coatings are dominated by amorphous structure. Microscopic observation and scratch test on these composite coatings demonstrate good adhesion between the magnet and the coatings. Remanence and coercivity of the plated magnet decrease with the applied coatings, but measured values are still very attractive for practical applications among known hard magnets

The Effect of Nano-TiC Addition on Sintered Nd-Fe-B Permanent Magnets

DEFF Research Database (Denmark)

Mural, Zorjana; Kollo, Lauri; Xia, Manlong

2017-01-01

This paper addresses the effect of nano-TiC addition on sintered Nd-Fe-B permanent magnets. TiC nanoparticles were added to sintered Nd-Fe-B magnets with a specific aim to improve the Curie temperature and thermal stability. A standard powder metallurgy route was adopted to prepare the magnets....... It was found that introducing nano-TiC prior to jet milling was effective as the nanoparticles dispersed in the final alloy, concentcalcrating in the neodymium-rich phase of the magnets. Magnets with optimal properties were obtained with the addition of 1 wt% TiC nanoparticles. The hysteresis loop...

Texture formation in iron particles using mechanical milling with graphite as a milling aid

Energy Technology Data Exchange (ETDEWEB)

Motozuka, S.; Hayashi, K. [Department of Mechanical Engineering, Gifu National College of Technology, 2236-2 Kamimakuwa, Motosu, Gifu 501-0495 (Japan); Tagaya, M. [Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka, Niigata 940-2188 (Japan); Morinaga, M. [Toyota Physical and Chemical Research Institute, 41-1, Yokomichi, Nagakute, Aichi 480-1192 (Japan)

2015-09-15

Crystallographically anisotropic platelet iron particles were successfully prepared using a conventional ball mill with addition of graphite (Gp) particles. The morphological and structural changes resulting from the milling were investigated using scanning electron microscopy and X-ray diffraction. The spherical iron particles were plastically deformed into platelet shapes during the milling. Simultaneously, it is suggested that the size of the Gp particles decreased and adhered as nanoparticles on the surface of the iron particles. The adhered Gp particles affected the plastic deformation behavior of the iron particles: the (001) planes of α-iron were oriented parallel to the particle face, and no preferred in-plane orientation was observed. This study not only details the preparation of soft magnetic metal particles that crystallographically oriented to enhance their magnetic properties but also provides new insight into the activities of the well-established and extensively studied mechanical milling method.

Texture formation in iron particles using mechanical milling with graphite as a milling aid

International Nuclear Information System (INIS)

Motozuka, S.; Hayashi, K.; Tagaya, M.; Morinaga, M.

2015-01-01

Crystallographically anisotropic platelet iron particles were successfully prepared using a conventional ball mill with addition of graphite (Gp) particles. The morphological and structural changes resulting from the milling were investigated using scanning electron microscopy and X-ray diffraction. The spherical iron particles were plastically deformed into platelet shapes during the milling. Simultaneously, it is suggested that the size of the Gp particles decreased and adhered as nanoparticles on the surface of the iron particles. The adhered Gp particles affected the plastic deformation behavior of the iron particles: the (001) planes of α-iron were oriented parallel to the particle face, and no preferred in-plane orientation was observed. This study not only details the preparation of soft magnetic metal particles that crystallographically oriented to enhance their magnetic properties but also provides new insight into the activities of the well-established and extensively studied mechanical milling method

Magnetization reversal processes in bonded magnets made from a mixture of Nd–(Fe,Co)–B and strontium ferrite powders

International Nuclear Information System (INIS)

Dospial, M.; Plusa, D.

2013-01-01

Isotropic epoxy-resin bonded magnets composed of different amounts of Magnequench MQP-B and strontium ferrite powders have been prepared using a compression molding technique. The magnetic parameters for magnets with different amounts of strontium ferrite and magnetization reversal processes have been studied by the measurement of the initial magnetization curves, the major hysteresis loops measured at a field up to 14 T and sets of recoil loops. The enhancement of μ 0 M R and μ 0 H C is observed in comparison with the calculated values. From the recoil loops the field dependences of the reversible, irreversible and total magnetization components and the differential susceptibilities were derived. From the dependence of the irreversible magnetization component versus an applied field it was deduced that the main mechanism of magnetization reversal process is the pinning of domain walls in MQP-B and strontium ferrite grains. The interactions between the magnetic particles and grains have been examined by the analysis of the δM plot. The δM behavior of magnets with ferrite has been interpreted as being composed of magnetizing exchange coupling and demagnetizing dipolar interactions. - Highlights: ► SrFe 12 O 19 addition causes a decrease in the H c , J R and (BH) max . ► H c and J R changes are not in agreement with dilution law. ► Main mechanism of the coercivity is the pinning of domain walls. ► In both magnets from pure powders dominant role plays long range dipolar interactions. ► Dipolar and exchange interaction are simultaneously present in hybrids but the dipolar are weaker.

Effect of Milling Condition on the Microstructure and the Properties of Nano structured Copper Tungsten Carbide Composite

International Nuclear Information System (INIS)

Mahani Yusoff; Zuhailawati Hussain

2011-01-01

In this work, in-situ Cu-WC composite has been fabricated by high energy milling followed by sintering. Cu, W and C mixture were mechanically alloyed in a planetary ball mill for 40 h at various milling speeds. Cu-W-C composite powders were cold compacted and sintered in argon ambient. Milled powder and sintered Cu-W-C composite were characterized in terms of Xray diffraction (XRD), field emission scanning electron microscopy (FESEM) and its properties. The result showed that carbide phases are only detected after sintering process. Greater amount of grain refinement during milling generates very high internal strain which reduced Cu crystallite size. It was found that formation of metastable, W 2 C has taken place before the formation of WC. With the presence of WC, the composite become increasingly harden with the increased of milling speed. Increasing milling speed also found to lower the electrical conductivity. (author)

The Influence of Milling and Spark Plasma Sintering on the Microstructure and Properties of the Al7075 Alloy