Development of a micro-mechanical valve in a novel glaucoma implant.

Science.gov (United States)

Siewert, Stefan; Schultze, Christine; Schmidt, Wolfram; Hinze, Ulf; Chichkov, Boris; Wree, Andreas; Sternberg, Katrin; Allemann, Reto; Guthoff, Rudolf; Schmitz, Klaus-Peter

2012-10-01

This paper describes methods for design, manufacturing and characterization of a micro-mechanical valve for a novel glaucoma implant. The implant is designed to drain aqueous humour from the anterior chamber of the eye into the suprachoroidal space in case of an elevated intraocular pressure (IOP). In contrast to any existing glaucoma drainage device (GDD), the valve mechanism is located in the anterior chamber and there, surrounded by aqueous humour, immune to fibrosis induced failure. For the prevention of hypotony the micro-mechanical valve is designed to open if the physiological pressure difference between the anterior chamber and the suprachoroidal space in the range of 0.8 mmHg to 3.7 mmHg is exceeded. In particular the work includes: (i) manufacturing and morphological characterization of polymer tubing, (ii) mechanical material testing as basis for (iii) the design of micro-mechanical valves using finite element analysis (FEA), (iv) manufacturing of microstent prototypes including micro-mechanical valves by femtosecond laser micromachining and (v) the experimental fluid-mechanical characterization of the manufactured microstent prototypes with regard to valve opening pressure. The considered materials polyurethane (PUR) and silicone (SIL) exhibit low elastic modulus and high extensibility. The unique valve design enables a low opening pressure of micro-mechanical valves. An ideal valve design for PUR and SIL with an experimentally determined opening pressure of 2 mmHg and 3.7 mmHg is identified. The presented valve approach is suitable for the inhibition of hypotony as a major limitation of today's GDD and will potentially improve the minimally invasive treatment of glaucoma.

Interfacial Micromechanics in Fibrous Composites: Design, Evaluation, and Models

Science.gov (United States)

Lei, Zhenkun; Li, Xuan; Qin, Fuyong; Qiu, Wei

2014-01-01

Recent advances of interfacial micromechanics in fiber reinforced composites using micro-Raman spectroscopy are given. The faced mechanical problems for interface design in fibrous composites are elaborated from three optimization ways: material, interface, and computation. Some reasons are depicted that the interfacial evaluation methods are difficult to guarantee the integrity, repeatability, and consistency. Micro-Raman study on the fiber interface failure behavior and the main interface mechanical problems in fibrous composites are summarized, including interfacial stress transfer, strength criterion of interface debonding and failure, fiber bridging, frictional slip, slip transition, and friction reloading. The theoretical models of above interface mechanical problems are given. PMID:24977189

Micromechanics of fracture in WC-Co hardmetals

International Nuclear Information System (INIS)

Dusza, J.; Parilak, L.

1986-01-01

A study has been made in WC-Co cemented carbides with grain sizes of 2.1 - 3.6 μm and 13 - 32 vol% Co, of the relationship between the fracture toughness and microstructural parameters and micromechanisms of fracture. Regression analyses have been used to derive empirical relationships between fracture toughness, and the binder spacing, the contiguity and the relative proportions of fracture in the binder phase and between contiguous WC grains

Potential constitutive models for salt: Survey of phenomenology, micromechanisms, and equations

International Nuclear Information System (INIS)

Senseny, P.E.; Hansen, F.D.

1987-12-01

Results are given of a literature survey performed to document the thermomechanical phenomena and micromechanical processes observed for salt over the ranges of stress and temperature of interest for a high-level nuclear repository. The elastic and thermal expansion behavior of salt can be readily modeled by the generalized Duhamel Neumann form of Hooke's law with temperature-dependent elastic constants and coefficient of thermal expansion. Inelastic deformation is primarily viscoplastic, but also has a brittle component. The observed phenomenological behavior of salt occurs because of micromechanical processes. To the extent that these processes have been studied, a summary of deformation mechanisms in natural salt is included in this report. Eight constitutive models that appear to be capable of modeling the viscoplastic deformation have been selected from the literature. Two models have been selected to model brittle deformation. Insufficient data are available to develop a model for failure. 92 refs., 39 figs., 6 tabs

A Large-scale Finite Element Model on Micromechanical Damage and Failure of Carbon Fiber/Epoxy Composites Including Thermal Residual Stress

Science.gov (United States)

Liu, P. F.; Li, X. K.

2018-06-01

The purpose of this paper is to study micromechanical progressive failure properties of carbon fiber/epoxy composites with thermal residual stress by finite element analysis (FEA). Composite microstructures with hexagonal fiber distribution are used for the representative volume element (RVE), where an initial fiber breakage is assumed. Fiber breakage with random fiber strength is predicted using Monte Carlo simulation, progressive matrix damage is predicted by proposing a continuum damage mechanics model and interface failure is simulated using Xu and Needleman's cohesive model. Temperature dependent thermal expansion coefficients for epoxy matrix are used. FEA by developing numerical codes using ANSYS finite element software is divided into two steps: 1. Thermal residual stresses due to mismatch between fiber and matrix are calculated; 2. Longitudinal tensile load is further exerted on the RVE to perform progressive failure analysis of carbon fiber/epoxy composites. Numerical convergence is solved by introducing the viscous damping effect properly. The extended Mori-Tanaka method that considers interface debonding is used to get homogenized mechanical responses of composites. Three main results by FEA are obtained: 1. the real-time matrix cracking, fiber breakage and interface debonding with increasing tensile strain is simulated. 2. the stress concentration coefficients on neighbouring fibers near the initial broken fiber and the axial fiber stress distribution along the broken fiber are predicted, compared with the results using the global and local load-sharing models based on the shear-lag theory. 3. the tensile strength of composite by FEA is compared with those by the shear-lag theory and experiments. Finally, the tensile stress-strain curve of composites by FEA is applied to the progressive failure analysis of composite pressure vessel.

Method for preventing micromechanical structures from adhering to another object

Science.gov (United States)

Smith, J.H.; Ricco, A.J.

1998-06-16

A method for preventing micromechanical structures from adhering to another object includes the step of immersing a micromechanical structure and its associated substrate in a chemical species that does not stick to itself. The method can be employed during the manufacture of micromechanical structures to prevent micromechanical parts from sticking or adhering to one another and their associated substrate surface. 3 figs.

Methodical treatment of dependent failures in risk analyses

International Nuclear Information System (INIS)

Hennings, W.; Mertens, J.

1987-06-01

In this report the state-of-the-art regarding dependent failures is compiled and commented on. Among others the following recommendations are infered: The term 'common mode failures' should be restricted to failures of redundant, similar components; the generic term is 'dependent failures' with the subsets 'causal failures' and 'common cause failures'. In risk studies, dependent failures should be covered as far as possible by 'explicit methods'. Nevertheless an uncovered rest remains, which should be accounted for by sensitivity analyses using 'implicit methods'. For this the homogeneous Marshall-Olkin model is recommended. Because the available reports on operating experiences only record 'common mode failures' systematically, it is recommended to additionally apply other methods, e.g. carry out a 'precursor study'. (orig.) [de

3rd Conference on Microactuators and Micromechanisms

CERN Document Server

Ananthasuresh, Gondi; Corves, Burkhard; Petuya, Victor

2015-01-01

This book contains applications of micromechanisms and microactuators in several very modern technical fields such as mechatronics, biomechanics, machines, micromachines, robotics and apparatuses. In connection with its topic, the work combines the theoretical results with experimental tests on micromechanisms and microactuators. The book presents the most recent research advances in Machine and Mechanisms Science. It includes the accepted reviewed papers of researchers specialized in the topics of the conference: microactuators and micro-assembly, micro sensors involving movable solids, micro-opto-mechanical devices, mechanical tools for cell and tissue studies, micromanipulation and micro-stages, micro-scale flight and swimming, micro-robotics and surgical tools, micron-scale power generation, miniature manufacturing machines, micromechatronics and micro-mechanisms, biomechanics micro and nano scales and control issues in microsystems.  The presented applications of micromechanisms and microactuators i...

Micromechanics of soil responses in cyclic simple shear tests

Directory of Open Access Journals (Sweden)

Cui Liang

2017-01-01

Full Text Available Offshore wind turbine (OWT foundations are subjected to a combination of cyclic and dynamic loading arising from wind, wave, rotor and blade shadowing. Under cyclic loading, most soils change their characteristics including stiffness, which may cause the system natural frequency to approach the loading frequency and lead to unplanned resonance and system damage or even collapse. To investigate such changes and the underlying micromechanics, a series of cyclic simple shear tests were performed on the RedHill 110 sand with different shear strain amplitudes, vertical stresses and initial relative densities of soil. The test results showed that: (a Vertical accumulated strain is proportional to the shear strain amplitude but inversely proportional to relative density of soil; (b Shear modulus increases rapidly in the initial loading cycles and then the rate of increase diminishes and the shear modulus remains below an asymptote; (c Shear modulus increases with increasing vertical stress and relative density, but decreasing with increasing strain amplitude. Coupled DEM simulations were performed using PFC2D to analyse the micromechanics underlying the cyclic behaviour of soils. Micromechanical parameters (e.g. fabric tensor, coordination number were examined to explore the reasons for the various cyclic responses to different shear strain amplitudes or vertical stresses. Both coordination number and magnitude of fabric anisotropy contribute to the increasing shear modulus.

Micromechanics based simulation of ductile fracture in structural steels

Science.gov (United States)

Yellavajjala, Ravi Kiran

The broader aim of this research is to develop fundamental understanding of ductile fracture process in structural steels, propose robust computational models to quantify the associated damage, and provide numerical tools to simplify the implementation of these computational models into general finite element framework. Mechanical testing on different geometries of test specimens made of ASTM A992 steels is conducted to experimentally characterize the ductile fracture at different stress states under monotonic and ultra-low cycle fatigue (ULCF) loading. Scanning electron microscopy studies of the fractured surfaces is conducted to decipher the underlying microscopic damage mechanisms that cause fracture in ASTM A992 steels. Detailed micromechanical analyses for monotonic and cyclic loading are conducted to understand the influence of stress triaxiality and Lode parameter on the void growth phase of ductile fracture. Based on monotonic analyses, an uncoupled micromechanical void growth model is proposed to predict ductile fracture. This model is then incorporated in to finite element program as a weakly coupled model to simulate the loss of load carrying capacity in the post microvoid coalescence regime for high triaxialities. Based on the cyclic analyses, an uncoupled micromechanics based cyclic void growth model is developed to predict the ULCF life of ASTM A992 steels subjected to high stress triaxialities. Furthermore, a computational fracture locus for ASTM A992 steels is developed and incorporated in to finite element program as an uncoupled ductile fracture model. This model can be used to predict the ductile fracture initiation under monotonic loading in a wide range of triaxiality and Lode parameters. Finally, a coupled microvoid elongation and dilation based continuum damage model is proposed, implemented, calibrated and validated. This model is capable of simulating the local softening caused by the various phases of ductile fracture process under

Neural Networks and Micromechanics

Science.gov (United States)

Kussul, Ernst; Baidyk, Tatiana; Wunsch, Donald C.

The title of the book, "Neural Networks and Micromechanics," seems artificial. However, the scientific and technological developments in recent decades demonstrate a very close connection between the two different areas of neural networks and micromechanics. The purpose of this book is to demonstrate this connection. Some artificial intelligence (AI) methods, including neural networks, could be used to improve automation system performance in manufacturing processes. However, the implementation of these AI methods within industry is rather slow because of the high cost of conducting experiments using conventional manufacturing and AI systems. To lower the cost, we have developed special micromechanical equipment that is similar to conventional mechanical equipment but of much smaller size and therefore of lower cost. This equipment could be used to evaluate different AI methods in an easy and inexpensive way. The proved methods could be transferred to industry through appropriate scaling. In this book, we describe the prototypes of low cost microequipment for manufacturing processes and the implementation of some AI methods to increase precision, such as computer vision systems based on neural networks for microdevice assembly and genetic algorithms for microequipment characterization and the increase of microequipment precision.

Mechanics of composite materials: Unified micromechanical approach

International Nuclear Information System (INIS)

Aboundi, J.

1991-01-01

Although many books have been written on the mechanics of composite materials, only a vew few have been devoted almost exclusively to the micromechanics aspects. The present monograph is devoted primarily to the micromechanics of fiber and particle reinforced composites with some additional treatment of laminates as well. Thus, this book would probably be more suitable as a reference book than a textbook

Micromechanisms with floating pivot

Science.gov (United States)

Garcia, Ernest J.

2001-03-06

A new class of tilting micromechanical mechanisms have been developed. These new mechanisms use floating pivot structures to relieve some of the problems encountered in the use of solid flexible pivots.

Micromechanics of hierarchical materials

DEFF Research Database (Denmark)

Mishnaevsky, Leon, Jr.

2012-01-01

A short overview of micromechanical models of hierarchical materials (hybrid composites, biomaterials, fractal materials, etc.) is given. Several examples of the modeling of strength and damage in hierarchical materials are summarized, among them, 3D FE model of hybrid composites...... with nanoengineered matrix, fiber bundle model of UD composites with hierarchically clustered fibers and 3D multilevel model of wood considered as a gradient, cellular material with layered composite cell walls. The main areas of research in micromechanics of hierarchical materials are identified, among them......, the investigations of the effects of load redistribution between reinforcing elements at different scale levels, of the possibilities to control different material properties and to ensure synergy of strengthening effects at different scale levels and using the nanoreinforcement effects. The main future directions...

Spacecraft electrical power subsystem: Failure behavior, reliability, and multi-state failure analyses

International Nuclear Information System (INIS)

Kim, So Young; Castet, Jean-Francois; Saleh, Joseph H.

2012-01-01

This article investigates the degradation and failure behavior of spacecraft electrical power subsystem (EPS) on orbit. First, this work provides updated statistical reliability and multi-state failure analyses of spacecraft EPS and its different constituents, namely the batteries, the power distribution, and the solar arrays. The EPS is shown to suffer from infant mortality and to be a major driver of spacecraft unreliability. Over 25% of all spacecraft failures are the result of EPS failures. As a result, satellite manufacturers may wish to pursue targeted improvement to this subsystem, either through better testing or burn-in procedures, better design or parts selection, or additional redundancy. Second, this work investigates potential differences in the EPS degradation and failure behavior for spacecraft in low earth orbits (LEO) and geosynchronous orbits (GEO). This analysis was motivated by the recognition that the power/load cycles and the space environment are significantly different in LEO and GEO, and as such, they may result in different failure behavior for the EPS in these two types of orbits. The results indicate, and quantify the extent to which, the EPS fails differently in LEO and GEO, both in terms of frequency and severity of failure events. A casual summary of the findings can be stated as follows: the EPS fails less frequently but harder (with fatal consequences to the spacecraft) in LEO than in GEO.

A micromechanical study of porous composites under longitudinal shear and transverse normal loading

DEFF Research Database (Denmark)

Ashouri Vajari, Danial

2015-01-01

The mechanical response of porous unidirectional composites under transverse normal and longitudinal shear loading is studied using the finite element analysis. The 3D model includes discrete and random distribution of fibers and voids. The micromechanical failure mechanisms are taken into account....... Finally, the computational prediction of the porous composite in the transverse normal-longitudinal shear stress space is obtained and compared with Puck's model. The results show that both interfaces with low fracture toughness and microvoids with even small void volume fraction can significantly reduce...

Micromechanical modelling of mechanical behaviour and strength of wood

DEFF Research Database (Denmark)

Mishnaevsky, Leon; Qing, Hai

2008-01-01

An overview of the micromechanical theoretical and numerical models of wood is presented. Different methods of analysis of the effects of wood microstructures at different scale levels on the mechanical behaviour, deformation and strength of wood are discussed and compared. Micromechanical models...

Micromechanical validation of a mesomodel for plasticity in composites

NARCIS (Netherlands)

van der Meer, F.P.

2016-01-01

In this paper, the performance of a recent homogenized orthotropic plasticity model for fiber reinforced composites (Vogler et al. (2013)) is investigated by comparing the model response against a micromechanical model. It is assumed that the micromechanical model which contains a recent

Non-driven micromechanical gyroscopes and their applications

CERN Document Server

Zhang, Fuxue; Wang, Guosheng

2018-01-01

This book comprehensively and systematically introduces readers to the theories, structures, performance and applications of non-driven mechanical and non-driven micromechanical gyroscopes. The book is divided into three parts, the first of which mainly addresses mathematic models, precision, performance and operating error in non-driven mechanical gyroscopes. The second part focuses on the operating theory, error, phase shift and performance experiments involving non-driven micromechanical gyroscopes in rotating flight carriers, while the third part shares insights into the application of non-driven micromechanical gyroscopes in control systems for rotating flight carriers. The book offers a unique resource for all researchers and engineers who are interested in the use of inertial devices and automatic control systems for rotating flight carriers.  It can also serve as a reference book for undergraduates, graduates and instructors in related fields at colleges and universities.

Micro-Mechanical Temperature Sensors

DEFF Research Database (Denmark)

Larsen, Tom

Temperature is the most frequently measured physical quantity in the world. The field of thermometry is therefore constantly evolving towards better temperature sensors and better temperature measurements. The aim of this Ph.D. project was to improve an existing type of micro-mechanical temperature...... sensor or to develop a new one. Two types of micro-mechanical temperature sensors have been studied: Bilayer cantilevers and string-like beam resonators. Both sensor types utilize thermally generated stress. Bilayer cantilevers are frequently used as temperature sensors at the micro-scale, and the goal....... The reduced sensitivity was due to initial bending of the cantilevers and poor adhesion between the two cantilever materials. No further attempts were made to improve the sensitivity of bilayer cantilevers. The concept of using string-like resonators as temperature sensors has, for the first time, been...

Safety and deterministic failure analyses in high-beta D-D tokamak reactors

International Nuclear Information System (INIS)

Selcow, E.C.

1984-01-01

Safety and deterministic failure analyses were performed to compare major component failure characteristics for different high-beta D-D tokamak reactors. The primary focus was on evaluating damage to the reactor facility. The analyses also considered potential hazards to the general public and operational personnel. Parametric designs of high-beta D-D tokamak reactors were developed, using WILDCAT as the reference. The size, and toroidal field strength were reduced, and the fusion power increased in an independent manner. These changes were expected to improve the economics of D-D tokamaks. Issues examined using these designs were radiation induced failurs, radiation safety, first wall failure from plasma disruptions, and toroidal field magnet coil failure

Micromechanical thermogravimetry

Science.gov (United States)

Berger, R.; Lang, H. P.; Gerber, Ch.; Gimzewski, J. K.; Fabian, J. H.; Scandella, L.; Meyer, E.; Güntherodt, H.-J.

1998-09-01

We demonstrate a new method for thermal analysis of nanogram quantities of material using a micromechanical thermogravimetric technique. The cantilever-type device uses an integrated piezoresistor to sense bending and simultaneously to ramp the temperature and control temperature cycles. It has a mass resolution in the picogram range. A quantitative analysis of the dehydration of copper-sulfate-pentahydrate (CuSO 4·5H 2O) is presented. The technique outperforms current thermogravimetric approaches by five orders of magnitude.

Sensitivity improvement techniques for micromechanical vibrating accelerometers

Directory of Open Access Journals (Sweden)

Vtorushin Sergey

2016-01-01

Full Text Available The paper presents the problems of detecting a desired signal generated by micromechanical vibrating accelerometer. Three detection methods, namely frequency, amplitude and phase are considered in this paper. These methods are used in micromechanical vibrating accelerometers that incorporate a force sensitive element which transforms measured acceleration into the output signal. Investigations are carried out using the ANSYS finite element program and MATLAB/Simulink support package. Investigation results include the comparative analysis of the output signal characteristics obtained by the different detection methods.

Micromechanical Analyses of Sturzstroms

Science.gov (United States)

Imre, Bernd; Laue, Jan; Springman, Sarah M.

2010-05-01

have been made observable and reproducible within a physical and a distinct element numerical modelling environment (DEM). As link between field evidence gained from the deposits of natural sturzstroms, the physical model within the ETH Geotechnical Drum Centrifuge (Springman et al., 2001) and the numerical model PFC-3D (Cundall and Strack, 1979; Itasca, 2005), serves a deterministic fractal analytical comminution model (Sammis et al., 1987; Steacy and Sammis, 1991). This approach allowed studying the effects of dynamic fragmentation within sturzstroms at true (macro) scale within the distinct element model, by allowing for a micro-mechanical, distinct particle based, and cyclic description of fragmentation at the same time, without losing significant computational efficiency. Theses experiments indicate rock mass and boundary conditions, which allow an alternating fragmenting and dilating dispersive regime to evolve and to be sustained long enough to replicate the spreading and run out of sturzstroms. The fragmenting spreading model supported here is able to explain the run out of a dry granular flow, beyond the travel distance predicted by a Coulomb frictional sliding model, without resorting to explanations by mechanics that can only be valid for certain, specific of the boundary conditions. The implications derived suggest that a sturzstrom, because of its strong relation to internal fractal fragmentation and other inertial effects, constitutes a landslide category of its own. Its mechanics differ significantly from all other gravity driven mass flows. This proposition does not exclude the possible appearance of frictionites, Toma hills or suspension flows etc., but it considers them as secondary features. The application of a fractal comminution model to describe natural and experimental sturzstrom deposits turned out to be a useful tool for sturzstrom research. Implemented within the DEM, it allows simulating the key features of sturzstrom successfully and

Reducing support loss in micromechanical ring resonators using phononic band-gap structures

Energy Technology Data Exchange (ETDEWEB)

Hsu, Feng-Chia; Huang, Tsun-Che; Wang, Chin-Hung; Chang, Pin [Industrial Technology Research Institute-South, Tainan 709, Taiwan (China); Hsu, Jin-Chen, E-mail: fengchiahsu@itri.org.t, E-mail: hsujc@yuntech.edu.t [Department of Mechanical Engineering, National Yunlin University of Science and Technology, Douliou, Yunlin 64002, Taiwan (China)

2011-09-21

In micromechanical resonators, energy loss via supports into the substrates may lead to a low quality factor. To eliminate the support loss, in this paper a phononic band-gap structure is employed. We demonstrate a design of phononic-crystal (PC) strips used to support extensional wine-glass mode ring resonators to increase the quality factor. The PC strips are introduced to stop elastic-wave propagation by the band-gap and deaf-band effects. Analyses of resonant characteristics of the ring resonators and the dispersion relations, eigenmodes, and transmission properties of the PC strips are presented. With the proposed resonator architecture, the finite-element simulations show that the leaky power is effectively reduced and the stored energy inside the resonators is enhanced simultaneously as the operating frequencies of the resonators are within the band gap or deaf bands. Realization of a high quality factor micromechanical ring resonator with minimized support loss is expected.

Reducing support loss in micromechanical ring resonators using phononic band-gap structures

International Nuclear Information System (INIS)

Hsu, Feng-Chia; Huang, Tsun-Che; Wang, Chin-Hung; Chang, Pin; Hsu, Jin-Chen

2011-01-01

In micromechanical resonators, energy loss via supports into the substrates may lead to a low quality factor. To eliminate the support loss, in this paper a phononic band-gap structure is employed. We demonstrate a design of phononic-crystal (PC) strips used to support extensional wine-glass mode ring resonators to increase the quality factor. The PC strips are introduced to stop elastic-wave propagation by the band-gap and deaf-band effects. Analyses of resonant characteristics of the ring resonators and the dispersion relations, eigenmodes, and transmission properties of the PC strips are presented. With the proposed resonator architecture, the finite-element simulations show that the leaky power is effectively reduced and the stored energy inside the resonators is enhanced simultaneously as the operating frequencies of the resonators are within the band gap or deaf bands. Realization of a high quality factor micromechanical ring resonator with minimized support loss is expected.

Micromechanics modelling of ductile fracture

CERN Document Server

Chen, Zengtao

2013-01-01

This book summarizes research advances in micromechanics modelling of ductile fractures made in the past two decades. The ultimate goal of this book is to reach manufacturing frontline designers and materials engineers by providing a user-oriented, theoretical background of micromechanics modeling. Accordingly, the book is organized in a unique way and presents a vigorous damage percolation model developed by the authors over the last ten years. This model overcomes almost all difficulties of the existing models and can be used to completely accommodate ductile damage development within a single, measured microstructure frame. Related void damage criteria including nucleation, growth and coalescence are then discussed in detail: how they are improved, when and where they are used in the model, and how the model performs in comparison with the existing models. Sample forming simulations are provided to illustrate the model’s performance.

Micromechanical analysis of porous SMA

International Nuclear Information System (INIS)

Sepe, V; Marfia, S; Sacco, E; Auricchio, F

2015-01-01

The present paper deals with computational micromechanical analyses of porous shape memory alloy (SMA). Porous SMAs are considered composite materials made of a dense SMA matrix including voids. A three-dimensional constitutive law is presented for the dense SMA able to reproduce the pseudo-elastic as well as the shape memory effects and, moreover, to account for the different elastic properties of the austenite and martensite phases. Furthermore, a numerical procedure is developed and the overall behavior of the porous SMA is recovered studying a representative volume element. Comparisons between the numerical results, recovered using the proposed modeling, and experimental data available in the literature are presented. The case of closed and open porosity is investigated. Parametric studies have been conducted in order to investigate the influence of the porosity, the shape and orientation of the pores on the overall mechanical response and, mainly, on the energy absorption dissipation capability. (paper)

Mini-Symposium on Micromechanics at the CSME Mechanical Engineering Forum

CERN Document Server

Muschik, W

1991-01-01

This volume contains the lectures presented at the mini-symposium on "Micromechanics" held in conjunction with the CSME Mechanical Engineer­ ing Forum 1990 between the 3rd and 8th June, 1990 at the University of Toronto, Canada. The expressed purpose of this symposium was to discuss some recent developments in the Micromechanics of Materials and how ad­ vances in this field now relate to the solution of practical engineer­ ing problems. Due to the time limit set for this section of the Engineer­ ing Forum as well as the restriction on the number of papers to be pre­ sented, it was not possible to cover a much wider range of topics. How­ ever, an attempt was made to include the most important advances asso­ ciated with the progress made in micromechanics in its application to material science and engineering over the past decade. Thus, the topics are concerned with: the fundamental aspects of the thermodynamics of structured solids (part I), - the micromechanical behaviour of alloys (part II), - the mod...

A Micromechanical RF Channelizer

Science.gov (United States)

Akgul, Mehmet

The power consumption of a radio generally goes as the number and strength of the RF signals it must process. In particular, a radio receiver would consume much less power if the signal presented to its electronics contained only the desired signal in a tiny percent bandwidth frequency channel, rather than the typical mix of signals containing unwanted energy outside the desired channel. Unfortunately, a lack of filters capable of selecting single channel bandwidths at RF forces the front-ends of contemporary receivers to accept unwanted signals, and thus, to operate with sub-optimal efficiency. This dissertation focuses on the degree to which capacitive-gap transduced micromechanical resonators can achieve the aforementioned RF channel-selecting filters. It aims to first show theoretically that with appropriate scaling capacitive-gap transducers are strong enough to meet the needed coupling requirements; and second, to fully detail an architecture and design procedure needed to realize said filters. Finally, this dissertation provides an actual experimentally demonstrated RF channel-select filter designed using the developed procedures and confirming theoretical predictions. Specifically, this dissertation introduces four methods that make possible the design and fabrication of RF channel-select filters. The first of these introduces a small-signal equivalent circuit for parallel-plate capacitive-gap transduced micromechanical resonators that employs negative capacitance to model the dependence of resonance frequency on electrical stiffness in a way that facilitates the analysis of micromechanical circuits loaded with arbitrary electrical impedances. The new circuit model not only correctly predicts the dependence of electrical stiffness on the impedances loading the input and output electrodes of parallel-plate capacitive-gap transduced micromechanical device, but does so in a visually intuitive way that identifies current drive as most appropriate for

Micromechanical sensors for the measurement of biopolymer degradation

DEFF Research Database (Denmark)

Keller, Stephan Sylvest; Gammelgaard, Lene; Jensen, M P

2011-01-01

We present microcantilever-based sensors for the characterization of biopolymer degradation by enzymes. Thin films of Poly(L-lactide) (PLLA) were spray-coated onto SU-8 cantilevers with well-known material properties and dimensions. The micromechanical sensors were immersed in solutions of protei......We present microcantilever-based sensors for the characterization of biopolymer degradation by enzymes. Thin films of Poly(L-lactide) (PLLA) were spray-coated onto SU-8 cantilevers with well-known material properties and dimensions. The micromechanical sensors were immersed in solutions...

Micromechanical models to guide the development of synthetic ‘brick and mortar’ composites

Science.gov (United States)

Begley, Matthew R.; Philips, Noah R.; Compton, Brett G.; Wilbrink, David V.; Ritchie, Robert O.; Utz, Marcel

2012-08-01

This paper describes a micromechanical analysis of the uniaxial response of composites comprising elastic platelets (bricks) bonded together with thin elastic perfectly plastic layers (mortar). The model yields closed-form results for the spatial variation of displacements in the bricks as a function of constituent properties, which can be used to calculate the effective properties of the composite, including elastic modulus, strength and work-to-failure. Regime maps are presented which indicate critical stresses for failure of the bricks and mortar as a function of constituent properties and brick architecture. The solution illustrates trade-offs between elastic modulus, strength and dissipated work that are a result of transitions between various failure mechanisms associated with brick rupture and rupture of the interfaces. Detailed scaling relationships are presented with the goal of providing material developers with a straightforward means to identify synthesis targets that balance competing mechanical behaviors and optimize material response. Ashby maps are presented to compare potential brick and mortar composites with existing materials, and identify future directions for material development.

Technical report on micro-mechanical versus conventional modelling in non-linear fracture mechanics

International Nuclear Information System (INIS)

2001-07-01

While conventional fracture mechanics is capable of predicting crack growth behaviour if sufficient experimental observations are available, micro-mechanical modelling can both increase the accuracy of these predictions and model phenomena that are inaccessible by the conventional theory such as the ductile-cleavage temperature transition. A common argument against micro-mechanical modelling is that it is too complicated for use in routine engineering applications. This is both a computational and an educational problem. That micro-mechanical modelling is unnecessarily complicated is certainly true in many situations. The on-going development of micro-mechanical models, computational algorithms and computer speed will however most probably diminish the computational problem rather rapidly. Compare for instance the rate of development of computational methods for structural analysis. Meanwhile micro-mechanical modelling may serve as a tool by which more simplified engineering methods can be validated. The process of receiving a wide acceptance of the new methods is probably much slower. This involves many steps. First the research community must be in reasonable agreement on the methods and their use. Then the methods have to be implemented into computer software and into code procedures. The development and acceptance of conventional fracture mechanics may serve as an historical example of the time required before a new methodology has received a wide usage. The CSNI Working Group on Integrity and Ageing (IAGE) decided to carry out a report on micro-mechanical modeling to promote this promising and valuable technique. The report presents a comparison with non-linear fracture mechanics and highlights key aspects that could lead to a better knowledge and accurate predictions. Content: - 1. Introduction; - 2. Concepts of non-linear fracture mechanics with point crack tip modelling; - 3. Micro-mechanical models for cleavage fracture; - 4, Micro-mechanical modelling of

An Extension of Holographic Moiré to Micromechanics

Science.gov (United States)

Sciammarella, C. A.; Sciammarella, F. M.

The electronic Holographic Moiré is an ideal tool for micromechanics studies. It does not require a modification of the surface by the introduction of a reference grating. This is of particular advantage when dealing with materials such as solid propellant grains whose chemical nature and surface finish makes the application of a reference grating very difficult. Traditional electronic Holographic Moiré presents some difficult problems when large magnifications are needed and large rigid body motion takes place. This paper presents developments that solves these problems and extends the application of the technique to micromechanics.

A novel micromechanical flow regulator

NARCIS (Netherlands)

van Toor, M.W.; van Toor, M.W.; Lammerink, Theodorus S.J.; Gardeniers, Johannes G.E.; Elwenspoek, Michael Curt; Monsma, D.J.

1996-01-01

A new concept for a micromechanical flow regulator is presented. Regulation of the flow is achieved using variation of channel length instead of channel diameter. Several design concepts together with their application in fluidic systems are presented. A regulator for biomedical use, as a part of a

A novel micromechanical flow controller

NARCIS (Netherlands)

van Toor, M.W.; van Toor, M.W.; Lammerink, Theodorus S.J.; Gardeniers, Johannes G.E.; Elwenspoek, Michael Curt; Monsma, D.J.

A new concept for a micromechanical flow regulator is presented. Regulation of the flow is achieved using variation of channel length instead of channel diameter. Several design concepts together with their application in fluidic systems are presented. A regulator for biomedical use, as a part of a

Versatile Micromechanics Model for Multiscale Analysis of Composite Structures

Science.gov (United States)

Kwon, Y. W.; Park, M. S.

2013-08-01

A general-purpose micromechanics model was developed so that the model could be applied to various composite materials such as reinforced by particles, long fibers and short fibers as well as those containing micro voids. Additionally, the model can be used with hierarchical composite materials. The micromechanics model can be used to compute effective material properties like elastic moduli, shear moduli, Poisson's ratios, and coefficients of thermal expansion for the various composite materials. The model can also calculate the strains and stresses at the constituent material level such as fibers, particles, and whiskers from the composite level stresses and strains. The model was implemented into ABAQUS using the UMAT option for multiscale analysis. An extensive set of examples are presented to demonstrate the reliability and accuracy of the developed micromechanics model for different kinds of composite materials. Another set of examples is provided to study the multiscale analysis of composite structures.

Micromechanics of heterogeneous materials

CERN Document Server

Buryachenko, Valeriy

2007-01-01

Here is an accurate and timely account of micromechanics, which spans materials science, mechanical engineering, applied mathematics, technical physics, geophysics, and biology. The book features rigorous and unified theoretical methods of applied mathematics and statistical physics in the material science of microheterogeneous media. Uniquely, it offers a useful demonstration of the systematic and fundamental research of the microstructure of the wide class of heterogeneous materials of natural and synthetic nature.

Characterization of Bitumen Micro-Mechanical Behaviors Using AFM, Phase Dynamics Theory and MD Simulation

Directory of Open Access Journals (Sweden)

Yue Hou

2017-02-01

Full Text Available Fundamental understanding of micro-mechanical behaviors in bitumen, including phase separation, micro-friction, micro-abrasion, etc., can help the pavement engineers better understand the bitumen mechanical performances at macroscale. Recent researches show that the microstructure evolution in bitumen will directly affect its surface structure and micro-mechanical performance. In this study, the bitumen microstructure and micro-mechanical behaviors are studied using Atomic Force Microscopy (AFM experiments, Phase Dynamics Theory and Molecular Dynamics (MD Simulation. The AFM experiment results show that different phase-structure will occur at the surface of the bitumen samples under certain thermodynamic conditions at microscale. The phenomenon can be explained using the phase dynamics theory, where the effects of stability parameter and temperature on bitumen microstructure and micro-mechanical behavior are studied combined with MD Simulation. Simulation results show that the saturates phase, in contrast to the naphthene aromatics phase, plays a major role in bitumen micro-mechanical behavior. A high stress zone occurs at the interface between the saturates phase and the naphthene aromatics phase, which may form discontinuities that further affect the bitumen frictional performance.

Characterization of Bitumen Micro-Mechanical Behaviors Using AFM, Phase Dynamics Theory and MD Simulation.

Science.gov (United States)

Hou, Yue; Wang, Linbing; Wang, Dawei; Guo, Meng; Liu, Pengfei; Yu, Jianxin

2017-02-21

Fundamental understanding of micro-mechanical behaviors in bitumen, including phase separation, micro-friction, micro-abrasion, etc., can help the pavement engineers better understand the bitumen mechanical performances at macroscale. Recent researches show that the microstructure evolution in bitumen will directly affect its surface structure and micro-mechanical performance. In this study, the bitumen microstructure and micro-mechanical behaviors are studied using Atomic Force Microscopy (AFM) experiments, Phase Dynamics Theory and Molecular Dynamics (MD) Simulation. The AFM experiment results show that different phase-structure will occur at the surface of the bitumen samples under certain thermodynamic conditions at microscale. The phenomenon can be explained using the phase dynamics theory, where the effects of stability parameter and temperature on bitumen microstructure and micro-mechanical behavior are studied combined with MD Simulation. Simulation results show that the saturates phase, in contrast to the naphthene aromatics phase, plays a major role in bitumen micro-mechanical behavior. A high stress zone occurs at the interface between the saturates phase and the naphthene aromatics phase, which may form discontinuities that further affect the bitumen frictional performance.

Micromechanical modeling of strength and damage of fiber reinforced composites

Energy Technology Data Exchange (ETDEWEB)

Mishnaevsky, L. Jr.; Broendsted, P.

2007-03-15

The report for the first year of the EU UpWind project includes three parts: overview of concepts and methods of modelling of mechanical behavior, deformation and damage of unidirectional fiber reinforced composites, development of computational tools for the automatic generation of 3D micromechanical models of fiber reinforced composites, and micromechanical modelling of damage in FRC, and phenomenological analysis of the effect of frequency of cyclic loading on the lifetime and damage evolution in materials. (au)

EDITORIAL: Selected papers from the 22nd MicroMechanics and Microsystems Europe Workshop (MME 2011) Selected papers from the 22nd MicroMechanics and Microsystems Europe Workshop (MME 2011)

Science.gov (United States)

Ohlckers, Per

2012-07-01

This special section of Journal of Micromechanics and Microengineering is a selection of 13 of the best papers presented at the 22nd Micromechanics and Microsystems Europe Workshop, which was arranged in Toensberg, Norway, 19-22 June, 2011. 110 participants attended the 3 day workshop that had 5 invited keynote speakers and 80 submitted poster presentations. The MME Workshop is organized every year to gather mostly European scientists and people from industry to discuss topics related to research in micromechanics and microsystems in an informal manner. A distinct feature of this specialized workshop is to be an excellent venue for young scientists in the field, such as PhD students, to present their latest work. This workshop series was inaugurated in Enschede, the Netherlands in 1989, followed by: Berlin, Germany (1990), Leuven, Belgium (1992), Neuchatel, Switzerland (1993), Pisa, Italy (1994), Copenhagen, Denmark (1995), Barcelona, Spain (1996) [1], Southampton, UK (1997) [2], Ulvik, Norway (1998) [3], Gif-sur-Yvette, France (1999) [4], Uppsala, Sweden (2000), Cork, Ireland (2001) [5], Sinaia, Romania (2002) [6], Delft, The Netherlands (2003) [7], Leuven, Belgium (2004) [8], Goteborg, Sweden (2005) [9], Southampton, UK (2006) [10], Guimaraes, Portugal (2007) [11], Aachen, Germany (2008) [12], Toulouse, France (2009) [13] and Enschede, the Netherlands (2010) [14]. The workshop series has remained remarkably true to its original concept such as still having micromechanics as a priority topic while, at the same time, adapting to recent research topics such as microsystems integration. It is nice to observe that an earlier fragmented and mostly academic research field now has matured into a very strong industrial field being one of the fastest growing industries in the world, with successful applications on all levels from high end to low end, from space to consumer applications, with the inclusion of microsystems in smartphones such as three-axis accelerometers and

4th Conference on Microactuators and Micromechanisms

CERN Document Server

Corves, Burkhard; Jensen, Brian; Lovasz, Erwin-Christian

2017-01-01

This book brings together investigations which combine theoretical and experimental results related to such systems as capsule micromechanisms, active micro catheters, nanotube vascular stents, mechanisms for micromilling, different compliant mechanisms including grippers and compliant systems with actuators and sensors, microrobots based on vibrations, tactile sensors, tooth brackets, compliant valves, and space reflectors. This volume contains twenty-two contributions from researchers from ten countries, represented at the 4th Conference on Microactuators and Micromechanisms, which was held in 2016 in Ilmenau, Germany. The aim of the conference was to provide a special opportunity for a know-how exchange and collaboration in various disciplines concerning systems pertaining to micro-technology. This Conference was organized under the patronage of IFToMM (International Federation for the Promotion of Mechanism and Machine Science). .

A micromechanical approach to elastic and viscoelastic properties of fiber reinforced concrete

International Nuclear Information System (INIS)

Pasa Dutra, V.F.; Maghous, S.; Campos Filho, A.; Pacheco, A.R.

2010-01-01

Some aspects of the constitutive behavior of fiber reinforced concrete (FRC) are investigated within a micromechanical framework. Special emphasis is put on the prediction of creep of such materials. The linear elastic behavior is first examined by implementation of a Mori-Tanaka homogenization scheme. The micromechanical predictions for the overall stiffness prove to be very close to finite element solutions obtained from the numerical analysis of a representative elementary volume of FRC modeled as a randomly heterogeneous medium. The validation of the micromechanical concepts based on comparison with a set of experiments, shows remarkable predictive capabilities of the micromechanical representation. The second part of the paper is devoted to non-ageing viscoelasticity of FRC. Adopting a Zener model for the behavior of the concrete matrix and making use of the correspondence principle, the homogenized relaxation moduli are derived analytically. The validity of the model is established by mean of comparison with available experiment measurements of creep strain of steel fiber reinforced concrete under compressive load. Finally, the model predictions are compared to those derived from analytical models formulated within a one-dimensional setting.

EDITORIAL: The 19th MicroMechanics Europe Workshop (MME 2008) The 19th MicroMechanics Europe Workshop (MME 2008)

Science.gov (United States)

Schnakenberg, Uwe

2009-07-01

This special issue of Journal of Micromechanics and Microengineering is devoted to the 19th MicroMechanics Europe Workshop (MME 08), which took place at the RWTH Aachen University, Aachen, Germany, from 28-30 September, 2008. The workshop is a well recognized and established European event in the field of micro system technology using thin-film technologies for creating micro components, micro sensors, micro actuators, and micro systems. The first MME Workshop was held 1989 in Enschede (The Netherlands) and continued 1990 in Berlin (Germany), 1992 in Leuven (Belgium), and then was held annually in Neuchâtel (Switzerland), Pisa (Italy), Copenhagen (Denmark), Barcelona (Spain), Southampton (UK), Ulvik in Hardanger (Norway), Gif-sur-Yvette (France), Uppsala (Sweden), Cork (Ireland), Sinaia (Romania), Delft (The Netherlands), Leuven (Belgium), Göteborg (Sweden), Southampton (UK), and in Guimarães (Portugal). The two day workshop was attended by 180 delegates from 26 countries all over Europe and from Armenia, Austria, Bulgaria, Canada, China, Cuba, Iran, Japan, Korea, Malaysia, Taiwan, Turkey, and the United States of America. A total of 97 papers were accepted for presentation and there were a further five keynote presentations. I am proud to present 22 high-quality papers from MME 2008 selected for their novelty and relevance to Journal of Micromechanics and Microengineering. All the papers went through the regular reviewing procedure of IOP Publishing. I am eternally grateful to all the referees for their excellent work. I would also like to extend my thanks to the members of the Programme Committee of MME 2008, Dr Reinoud Wolffenbuttel, Professor José Higino Correia, and Dr Patrick Pons for pre-selection of the papers as well as to Professor Robert Puers for advice on the final selection of papers. My thanks also go to Dr Ian Forbes of IOP Publishing for managing the entire process and to the editorial staff of Journal of Micromechanics and Microengineering. I

Folded fabric tunes rock deformation and failure mode in the upper crust.

Science.gov (United States)

Agliardi, F; Dobbs, M R; Zanchetta, S; Vinciguerra, S

2017-11-10

The micro-mechanisms of brittle failure affect the bulk mechanical behaviour and permeability of crustal rocks. In low-porosity crystalline rocks, these mechanisms are related to mineralogy and fabric anisotropy, while confining pressure, temperature and strain rates regulate the transition from brittle to ductile behaviour. However, the effects of folded anisotropic fabrics, widespread in orogenic settings, on the mechanical behaviour of crustal rocks are largely unknown. Here we explore the deformation and failure behaviour of a representative folded gneiss, by combining the results of triaxial deformation experiments carried out while monitoring microseismicity with microstructural and damage proxies analyses. We show that folded crystalline rocks in upper crustal conditions exhibit dramatic strength heterogeneity and contrasting failure modes at identical confining pressure and room temperature, depending on the geometrical relationships between stress and two different anisotropies associated to the folded rock fabric. These anisotropies modulate the competition among quartz- and mica-dominated microscopic damage processes, resulting in transitional brittle to semi-brittle modes under P and T much lower than expected. This has significant implications on scales relevant to seismicity, energy resources, engineering applications and geohazards.

The micro-mechanics of strength, durability and damage tolerance in composites: new insights from high resolution computed tomography

Science.gov (United States)

Spearing, S. Mark; Sinclair, Ian

2016-07-01

Recent work, led by the authors, on impact damage resistance, particle toughening and tensile fibre failure is reviewed in order to illustrate the use of high-resolution X-ray tomography to observe and quantify damage mechanisms in carbon fibre composite laminates. Using synchrotron and micro-focus X-ray sources resolutions of less than 1 μm have been routinely achieved. This enables individual broken fibres and the micromechanisms of particle toughening to be observed and quantified. The data for fibre failure, cluster formation and overall tensile strength are compared with model predictions. This allows strategies for future model development to be identified. The overall implications for using such high-resolution 3-D measurements to inform a “data-rich mechanics” approach to materials evaluation and modeling is discussed.

An introduction to computational micromechanics

CERN Document Server

Zohdi, Tarek I; Zohdi, Tarek I

2004-01-01

In this, its second corrected printing, Zohdi and Wriggers' illuminating text presents a comprehensive introduction to the subject. The authors include in their scope basic homogenization theory, microstructural optimization and multifield analysis of heterogeneous materials. This volume is ideal for researchers and engineers, and can be used in a first-year course for graduate students with an interest in the computational micromechanical analysis of new materials.

Application of micromechanical models of ductile fracture initiation to reactor pressure vessel materials

International Nuclear Information System (INIS)

Chaouadi, R.; Walle, E. van; Fabry, A.; Velde, J. van de; Meester, P. de

1996-01-01

The aim of the current study is the application of local micromechanical models to predict crack initiation in ductile materials. Two reactor pressure vessel materials have been selected for this study: JRQ IAEA monitor base metal (A533B Cl.1) and Doel-IV weld material. Charpy impact tests have been performed in both un-irradiated and irradiated conditions. In addition to standard tensile tests, notched tensile specimens have been tested. The upper shelf energy of the weld material remains almost un-affected by irradiation, whereas a decrease of 20% is detected for the base metal. Accordingly, the tensile properties of the weld material do not reveal a clear irradiation effect on the yield and ultimate stresses, this in contrast to the base material flow properties. The tensile tests have been analyzed in terms of micromechanical models. A good correlation is found between the standard tests and the micromechanical models, that are able to predict the ductile damage evolution in these materials. Additional information on the ductility behavior of these materials is revealed by this micromechanical analysis

Micromechanical Models of Mechanical Response of High Performance Fibre Reinforced Cement Composites

DEFF Research Database (Denmark)

Li, V. C.; Mihashi, H.; Alwan, J.

1996-01-01

generation of FRC with high performance and economical viability, is in sight. However, utilization of micromechanical models for a more comprehensive set of important HPFRCC properties awaits further investigations into fundamental mechanisms governing composite properties, as well as intergrative efforts......The state-of-the-art in micromechanical modeling of the mechanical response of HPFRCC is reviewed. Much advances in modeling has been made over the last decade to the point that certain properties of composites can be carefully designed using the models as analytic tools. As a result, a new...... across responses to different load types. Further, micromechanical models for HPFRCC behavior under complex loading histories, including those in fracture, fatigue and multuaxial loading are urgently needed in order to optimize HPFRCC microstrcuctures and enable predictions of such material in structures...

Optical anisotropy in micromechanically rolled carbon nanotube forest

Science.gov (United States)

Razib, Mohd Asyraf bin Mohd; Rana, Masud; Saleh, Tanveer; Fan, Harrison; Koch, Andrew; Nojeh, Alireza; Takahata, Kenichi; Muthalif, Asan Gani Bin Abdul

2017-09-01

The bulk appearance of arrays of vertically aligned carbon nanotubes (VACNT arrays or CNT forests) is dark as they absorb most of the incident light. In this paper, two postprocessing techniques have been described where the CNT forest can be patterned by selective bending of the tips of the nanotubes using a rigid cylindrical tool. A tungsten tool was used to bend the vertical structure of CNTs with predefined parameters in two different ways as stated above: bending using the bottom surface of the tool (micromechanical bending (M2B)) and rolling using the side of the tool (micromechanical rolling (M2R)). The processed zone was investigated using a Field Emission Scanning Electron Microscope (FESEM) and optical setup to reveal the surface morphology and optical characteristics of the patterned CNTs on the substrate. Interestingly, the polarized optical reflection from the micromechanical rolled (M2R) sample was found to be significantly influenced by the rotation of the sample. It was observed that, if the polarization of the light is parallel to the alignment of the CNTs, the reflectance is at least 2 x higher than for the perpendicular direction. Furthermore, the reflectance varied almost linearly with good repeatability ( 10%) as the processed CNT forest sample was rotated from 0° to 90°. [Figure not available: see fulltext.

Micromechanical Resonator Driven by Radiation Pressure Force.

Science.gov (United States)

Boales, Joseph A; Mateen, Farrukh; Mohanty, Pritiraj

2017-11-22

Radiation pressure exerted by light on any surface is the pressure generated by the momentum of impinging photons. The associated force - fundamentally, a quantum mechanical aspect of light - is usually too small to be useful, except in large-scale problems in astronomy and astrodynamics. In atomic and molecular optics, radiation pressure can be used to trap or cool atoms and ions. Use of radiation pressure on larger objects such as micromechanical resonators has been so far limited to its coupling to an acoustic mode, sideband cooling, or levitation of microscopic objects. In this Letter, we demonstrate direct actuation of a radio-frequency micromechanical plate-type resonator by the radiation pressure force generated by a standard laser diode at room temperature. Using two independent methods, the magnitude of the resonator's response to forcing by radiation pressure is found to be proportional to the intensity of the incident light.

A failure at a licensed Atomic Energy Corporation facility, analysed thematically

International Nuclear Information System (INIS)

Wet, J.R. De

1995-01-01

A containment accident, which resulted in the release of uranium hexafluoride, is analysed in terms of risk engineering, failure minimisation, and economy and safety. The importance of South African statutory obligations in the management of nuclear risk is illustrated. (author)

The Micromechanics of Deformation and Failure in Metal-Matrix Composites

National Research Council Canada - National Science Library

Needleman, Alan

1997-01-01

.... However, metal-matrix composites often have low ductility and low fracture toughness. An improved understanding of the basic deformation and failure mechanisms is needed to overcome these problems...

2D micromechanical analysis of SiC/Al metal matrix composites under tensile, shear and combined tensile/shear loads

DEFF Research Database (Denmark)

Qing, Hai

2013-01-01

The influence of interface strength and loading conditions on the mechanical behavior of the metal-matrix composites is investigated in this paper. A program is developed to generate automatically 2D micromechanical Finite element (FE) models including interface, in which both the locations...... and dimensions of Silicon-Carbide (SiC) particles are randomly distributed. Finite element simulations of the deformation and damage evolution of SiC particle reinforced Aluminum (Al) alloy composite are carried out for different microstructures and interphase strengths under tensile, shear and combined tensile....../shear loads. 2D cohesive element is applied to describe the fracture and failure process of interphase, while the damage models based on maximum principal stress criterion and the stress triaxial indicator are developed within Abaqus/Standard Subroutine USDFLD to simulate the failure process of SiC particles...

Micromechanics of Composite Materials Governed by Vector Constitutive Laws

Science.gov (United States)

Bednarcyk, Brett A.; Aboudi, Jacob; Arnold, Steven M.

2017-01-01

The high-fidelity generalized method of cells micromechanics theory has been extended for the prediction of the effective property tensor and the corresponding local field distributions for composites whose constituents are governed by vector constitutive laws. As shown, the shear analogy, which can predict effective transverse properties, is not valid in the general three-dimensional case. Consequently, a general derivation is presented that is applicable to both continuously and discontinuously reinforced composites with arbitrary vector constitutive laws and periodic microstructures. Results are given for thermal and electric problems, effective properties and local field distributions, ordered and random microstructures, as well as complex geometries including woven composites. Comparisons of the theory's predictions are made to test data, numerical analysis, and classical expressions from the literature. Further, classical methods cannot provide the local field distributions in the composite, and it is demonstrated that, as the percolation threshold is approached, their predictions are increasingly unreliable. XXXX It has been observed that the bonding between the fibers and matrix in composite materials can be imperfect. In the context of thermal conductivity, such imperfect interfaces have been investigated in micromechanical models by Dunn and Taya (1993), Duan and Karihaloo (2007), Nan et al. (1997) and Hashin (2001). The present HFGMC micromechanical method, derived for perfectly bonded composite materials governed by vector constitutive laws, can be easily generalized to include the effects of weak bonding between the constituents. Such generalizations, in the context of the mechanical micromechanics problem, involve introduction of a traction-separation law at the fiber/matrix interface and have been presented by Aboudi (1987), Bednarcyk and Arnold (2002), Bednarcyk et al. (2004) and Aboudi et al. (2013) and will be addressed in the future.

Micromechanisms of damage in unidirectional fiber reinforced composites

DEFF Research Database (Denmark)

Mishnaevsky, Leon; Brøndsted, Povl

2009-01-01

strength of a composite at the pre-critical load, while the fibers with randomly distributed strengths lead to the higher strength of the composite at post-critical loads. In the case of randomly distributed fiber strengths, the damage growth in fibers seems to be almost independent from the crack length...... in the numerical experiments. The effect of the statistical variability of fiber strengths, viscosity of the polymer matrix as well as the interaction between the damage processes in matrix, fibers and interface are investigated numerically. It is demonstrated that fibers with constant strength ensure higher......Numerical micromechanical investigations of the mechanical behavior and damage evolution of glass fiber reinforced composites are presented. A program code for the automatic generation of 3D micromechanical unit cell models of composites with damageable elements is developed, and used...

Deformation, Failure, and Fatigue Life of SiC/Ti-15-3 Laminates Accurately Predicted by MAC/GMC

Science.gov (United States)

Bednarcyk, Brett A.; Arnold, Steven M.

2002-01-01

NASA Glenn Research Center's Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC) (ref.1) has been extended to enable fully coupled macro-micro deformation, failure, and fatigue life predictions for advanced metal matrix, ceramic matrix, and polymer matrix composites. Because of the multiaxial nature of the code's underlying micromechanics model, GMC--which allows the incorporation of complex local inelastic constitutive models--MAC/GMC finds its most important application in metal matrix composites, like the SiC/Ti-15-3 composite examined here. Furthermore, since GMC predicts the microscale fields within each constituent of the composite material, submodels for local effects such as fiber breakage, interfacial debonding, and matrix fatigue damage can and have been built into MAC/GMC. The present application of MAC/GMC highlights the combination of these features, which has enabled the accurate modeling of the deformation, failure, and life of titanium matrix composites.

Computational micromechanics of bioabsorbable magnesium stents.

Science.gov (United States)

Grogan, J A; Leen, S B; McHugh, P E

2014-06-01

Magnesium alloys are a promising candidate material for an emerging generation of absorbable metal stents. Due to its hexagonal-close-packed lattice structure and tendency to undergo twinning, the deformation behaviour of magnesium is quite different to that of conventional stent materials, such as stainless steel 316L and cobalt chromium L605. In particular, magnesium exhibits asymmetric plastic behaviour (i.e. different yield behaviours in tension and compression) and has lower ductility than these conventional alloys. In the on-going development of absorbable metal stents it is important to assess how the unique behaviour of magnesium affects device performance. The mechanical behaviour of magnesium stent struts is investigated in this study using computational micromechanics, based on finite element analysis and crystal plasticity theory. The plastic deformation in tension and bending of textured and non-textured magnesium stent struts with different numbers of grains through the strut dimension is investigated. It is predicted that, unlike 316L and L605, the failure risk and load bearing capacity of magnesium stent struts during expansion is not strongly affected by the number of grains across the strut dimensions; however texturing, which may be introduced and controlled in the manufacturing process, is predicted to have a significant influence on these measures of strut performance. Copyright © 2014 Elsevier Ltd. All rights reserved.

Micromechanical Analyses of Debonding and Matrix Cracking in Dual-Phase Materials

DEFF Research Database (Denmark)

Legarth, Brian Nyvang; Yang, Qingda

2016-01-01

Failure in elastic dual-phase materials under transverse tension is studied numerically. Cohesive zones represent failure along the interface and the augmented finite element method (A-FEM) is used for matrix cracking. Matrix cracks are formed at an angle of 55 deg - 60 deg relative to the loading...... direction, which is in good agreement with experiments. Matrix cracks initiate at the tip of the debond, and for equi-biaxial loading cracks are formed at both tips. For elliptical reinforcement the matrix cracks initiate at the narrow end of the ellipse. The load carrying capacity is highest for ligaments...

Probabilistic analyses of failure in reactor coolant piping

International Nuclear Information System (INIS)

Holman, G.S.

1984-01-01

LLNL is performing probabilistic reliability analyses of PWR and BWR reactor coolant piping for the NRC Office of Nuclear Regulatory Research. Specifically, LLNL is estimating the probability of a double-ended guillotine break (DEGB) in the reactor coolant loop piping in PWR plants, and in the main stream, feedwater, and recirculation piping of BWR plants. In estimating the probability of DEGB, LLNL considers two causes of pipe break: pipe fracture due to the growth of cracks at welded joints (direct DEGB), and pipe rupture indirectly caused by the seismically-induced failure of critical supports or equipment (indirect DEGB)

Micro-mechanical modeling of the cement-bone interface: the effect of friction, morphology and material properties on the micromechanical response.

NARCIS (Netherlands)

Janssen, D.; Mann, K.A.; Verdonschot, N.J.J.

2008-01-01

In order to gain insight into the micro-mechanical behavior of the cement-bone interface, the effect of parametric variations of frictional, morphological and material properties on the mechanical response of the cement-bone interface were analyzed using a finite element approach. Finite element

Micro-mechanical modeling of the cement-bone interface: the effect of friction morphology and material properties on the micromechanical response

NARCIS (Netherlands)

Janssen, Dennis; Mann, Kenneth A.; Verdonschot, Nicolaas Jacobus Joseph

2008-01-01

In order to gain insight into the micro-mechanical behavior of the cement–bone interface, the effect of parametric variations of frictional, morphological and material properties on the mechanical response of the cement–bone interface were analyzed using a finite element approach. Finite element

KOH concentration effect on the cycle life of nickel-hydrogen cells. Part 4: Results of failure analyses

Science.gov (United States)

Lim, H. S.; Verzwyvelt, S. A.

1989-01-01

KOH concentration effects on cycle life of a Ni/H2 cell have been studied by carrying out a cycle life test of ten Ni/H2 boiler plate cells which contain electrolytes of various KOH concentrations. Failure analyses of these cells were carried out after completion of the life test which accumulated up to 40,000 cycles at an 80 percent depth of discharge over a period of 3.7 years. These failure analyses included studies on changes of electrical characteristics of test cells and component analyses after disassembly of the cell. The component analyses included visual inspections, dimensional changes, capacity measurements of nickel electrodes, scanning electron microscopy, BET surface area measurements, and chemical analyses. Results have indicated that failure mode and change in the nickel electrode varied as the concentration was varied, especially, when the concentration was changed from 31 percent or higher to 26 percent or lower.

Electromagnetic and nuclear radiation detector using micromechanical sensors

Science.gov (United States)

Thundat, Thomas G.; Warmack, Robert J.; Wachter, Eric A.

2000-01-01

Electromagnetic and nuclear radiation is detected by micromechanical sensors that can be coated with various interactive materials. As the micromechanical sensors absorb radiation, the sensors bend and/or undergo a shift in resonance characteristics. The bending and resonance changes are detected with high sensitivity by any of several detection methods including optical, capacitive, and piezoresistive methods. Wide bands of the electromagnetic spectrum can be imaged with picoJoule sensitivity, and specific absorptive coatings can be used for selective sensitivity in specific wavelength bands. Microcantilevers coated with optical cross-linking polymers are useful as integrating optical radiation dosimeters. Nuclear radiation dosimetry is possible by fabricating cantilevers from materials that are sensitive to various nuclear particles or radiation. Upon exposure to radiation, the cantilever bends due to stress and its resonance frequency shifts due to changes in elastic properties, based on cantilever shape and properties of the coating.

Ductile sliding between mineral crystals followed by rupture of collagen crosslinks: experimentally supported micromechanical explanation of bone strength.

Science.gov (United States)

Fritsch, Andreas; Hellmich, Christian; Dormieux, Luc

2009-09-21

There is an ongoing discussion on how bone strength could be explained from its internal structure and composition. Reviewing recent experimental and molecular dynamics studies, we here propose a new vision on bone material failure: mutual ductile sliding of hydroxyapatite mineral crystals along layered water films is followed by rupture of collagen crosslinks. In order to cast this vision into a mathematical form, a multiscale continuum micromechanics theory for upscaling of elastoplastic properties is developed, based on the concept of concentration and influence tensors for eigenstressed microheterogeneous materials. The model reflects bone's hierarchical organization, in terms of representative volume elements for cortical bone, for extravascular and extracellular bone material, for mineralized fibrils and the extrafibrillar space, and for wet collagen. In order to get access to the stress states at the interfaces between crystals, the extrafibrillar mineral is resolved into an infinite amount of cylindrical material phases oriented in all directions in space. The multiscale micromechanics model is shown to be able to satisfactorily predict the strength characteristics of different bones from different species, on the basis of their mineral/collagen content, their intercrystalline, intermolecular, lacunar, and vascular porosities, and the elastic and strength properties of hydroxyapatite and (molecular) collagen.

A Simplified Micromechanical Modeling Approach to Predict the Tensile Flow Curve Behavior of Dual-Phase Steels

Science.gov (United States)

Nanda, Tarun; Kumar, B. Ravi; Singh, Vishal

2017-11-01

Micromechanical modeling is used to predict material's tensile flow curve behavior based on microstructural characteristics. This research develops a simplified micromechanical modeling approach for predicting flow curve behavior of dual-phase steels. The existing literature reports on two broad approaches for determining tensile flow curve of these steels. The modeling approach developed in this work attempts to overcome specific limitations of the existing two approaches. This approach combines dislocation-based strain-hardening method with rule of mixtures. In the first step of modeling, `dislocation-based strain-hardening method' was employed to predict tensile behavior of individual phases of ferrite and martensite. In the second step, the individual flow curves were combined using `rule of mixtures,' to obtain the composite dual-phase flow behavior. To check accuracy of proposed model, four distinct dual-phase microstructures comprising of different ferrite grain size, martensite fraction, and carbon content in martensite were processed by annealing experiments. The true stress-strain curves for various microstructures were predicted with the newly developed micromechanical model. The results of micromechanical model matched closely with those of actual tensile tests. Thus, this micromechanical modeling approach can be used to predict and optimize the tensile flow behavior of dual-phase steels.

Micro-mechanical modeling of the cement-bone interface: the effect of friction, morphology and material properties on the micromechanical response.

Science.gov (United States)

Janssen, Dennis; Mann, Kenneth A; Verdonschot, Nico

2008-11-14

In order to gain insight into the micro-mechanical behavior of the cement-bone interface, the effect of parametric variations of frictional, morphological and material properties on the mechanical response of the cement-bone interface were analyzed using a finite element approach. Finite element models of a cement-bone interface specimen were created from micro-computed tomography data of a physical specimen that was sectioned from an in vitro cemented total hip arthroplasty. In five models the friction coefficient was varied (mu=0.0; 0.3; 0.7; 1.0 and 3.0), while in one model an ideally bonded interface was assumed. In two models cement interface gaps and an optimal cement penetration were simulated. Finally, the effect of bone cement stiffness variations was simulated (2.0 and 2.5 GPa, relative to the default 3.0 GPa). All models were loaded for a cycle of fully reversible tension-compression. From the simulated stress-displacement curves the interface deformation, stiffness and hysteresis were calculated. The results indicate that in the current model the mechanical properties of the cement-bone interface were caused by frictional phenomena at the shape-closed interlock rather than by adhesive properties of the cement. Our findings furthermore show that in our model maximizing cement penetration improved the micromechanical response of the cement-bone interface stiffness, while interface gaps had a detrimental effect. Relative to the frictional and morphological variations, variations in the cement stiffness had only a modest effect on the micro-mechanical behavior of the cement-bone interface. The current study provides information that may help to better understand the load-transfer mechanisms taking place at the cement-bone interface.

Micromechanics-Based Structural Analysis (FEAMAC) and Multiscale Visualization within Abaqus/CAE Environment

Science.gov (United States)

Arnold, Steven M.; Bednarcyk, Brett A.; Hussain, Aquila; Katiyar, Vivek

2010-01-01

A unified framework is presented that enables coupled multiscale analysis of composite structures and associated graphical pre- and postprocessing within the Abaqus/CAE environment. The recently developed, free, Finite Element Analysis--Micromechanics Analysis Code (FEAMAC) software couples NASA's Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC) with Abaqus/Standard and Abaqus/Explicit to perform micromechanics based FEA such that the nonlinear composite material response at each integration point is modeled at each increment by MAC/GMC. The Graphical User Interfaces (FEAMAC-Pre and FEAMAC-Post), developed through collaboration between SIMULIA Erie and the NASA Glenn Research Center, enable users to employ a new FEAMAC module within Abaqus/CAE that provides access to the composite microscale. FEA IAC-Pre is used to define and store constituent material properties, set-up and store composite repeating unit cells, and assign composite materials as sections with all data being stored within the CAE database. Likewise FEAMAC-Post enables multiscale field quantity visualization (contour plots, X-Y plots), with point and click access to the microscale i.e., fiber and matrix fields).

PREFACE: 14th Micromechanics Europe Workshop (MME'03)

Science.gov (United States)

Wolffenbuttel, R. F.

2004-09-01

This special issue of the Journal of Micromechanics and Microengineering is devoted to the 14th Micromechanics Europe Workshop (MME'03), which was held at Delft University of Technology, The Netherlands on 2-4 November 2003. Papers have been selected from this workshop for presentation in this special issue. After a careful review by the MME'03 programme committee, 53 submissions were selected for poster presentation at the workshop in addition to 6 invited presentations. These covered the many aspects of our exciting field: technology, simulation, system design, fabrication and characterization in a wide range of applications. These contributions confirm a trend from technology-driven towards application-driven technological research. This trend has become possible because of the availability of mature fabrication technologies for micromechanical structures and is reflected by the presentations of some of the invited speakers. There were invited lectures about applications in the medical field, automotive and copiers, which provide evidence of the relevance of our work in society. Nevertheless, development of technologies rightfully remains a core activity of this workshop. This applies to both the introduction of new technologies, as was reflected by invited presentations on new trends in RIE and nanotechnology, and the addressing of manufacturing issues using available techniques, which will be demonstrated to be crucial in automotive applications. Out of these 59 papers 21 have been selected for presentation in this special issue. Since the scope of the workshop is somewhat wider than that of the journal, selection was based not only on the quality of the work, but also on suitability for presentation in the journal. Moreover, at the workshop, student presentation of research at an early stage was strongly encouraged, whereas publication of work in this journal requires a more advanced level. I would like to express my appreciation for the outstanding efforts

Micromechanics model for predicting anisotropic electrical conductivity of carbon fiber composite materials

Science.gov (United States)

Haider, Mohammad Faisal; Haider, Md. Mushfique; Yasmeen, Farzana

2016-07-01

Heterogeneous materials, such as composites consist of clearly distinguishable constituents (or phases) that show different electrical properties. Multifunctional composites have anisotropic electrical properties that can be tailored for a particular application. The effective anisotropic electrical conductivity of composites is strongly affected by many parameters including volume fractions, distributions, and orientations of constituents. Given the electrical properties of the constituents, one important goal of micromechanics of materials consists of predicting electrical response of the heterogeneous material on the basis of the geometries and properties of the individual phases, a task known as homogenization. The benefit of homogenization is that the behavior of a heterogeneous material can be determined without resorting or testing it. Furthermore, continuum micromechanics can predict the full multi-axial properties and responses of inhomogeneous materials, which are anisotropic in nature. Effective electrical conductivity estimation is performed by using classical micromechanics techniques (composite cylinder assemblage method) that investigates the effect of the fiber/matrix electrical properties and their volume fractions on the micro scale composite response. The composite cylinder assemblage method (CCM) is an analytical theory that is based on the assumption that composites are in a state of periodic structure. The CCM was developed to extend capabilities variable fiber shape/array availability with same volume fraction, interphase analysis, etc. The CCM is a continuum-based micromechanics model that provides closed form expressions for upper level length scales such as macro-scale composite responses in terms of the properties, shapes, orientations and constituent distributions at lower length levels such as the micro-scale.

Effect of High-Irradiance Light-Curing on Micromechanical Properties of Resin Cements

Directory of Open Access Journals (Sweden)

Anne Peutzfeldt

2016-01-01

Full Text Available This study investigated the influence of light-curing at high irradiances on micromechanical properties of resin cements. Three dual-curing resin cements and a light-curing flowable resin composite were light-cured with an LED curing unit in Standard mode (SM, High Power mode (HPM, or Xtra Power mode (XPM. Maximum irradiances were determined using a MARC PS radiometer, and exposure duration was varied to obtain two or three levels of radiant exposure (SM: 13.2 and 27.2 J/cm2; HPM: 15.0 and 30.4 J/cm2; XPM: 9.5, 19.3, and 29.7 J/cm2 (n=17. Vickers hardness (HV and indentation modulus (EIT were measured at 15 min and 1 week. Data were analyzed with nonparametric ANOVA, Wilcoxon-Mann-Whitney tests, and Spearman correlation analyses (α=0.05. Irradiation protocol, resin-based material, and storage time and all interactions influenced HV and EIT significantly (p≤0.0001. Statistically significant correlations between radiant exposure and HV or EIT were found, indicating that high-irradiance light-curing has no detrimental effect on the polymerization of resin-based materials (p≤0.0021. However, one resin cement was sensitive to the combination of irradiance and exposure duration, with high-irradiance light-curing resulting in a 20% drop in micromechanical properties. The results highlight the importance of manufacturers issuing specific recommendations for the light-curing procedure of each resin cement.

Cosserat moduli of anisotropic cancellous bone : A micromechanical analysis

NARCIS (Netherlands)

Fatemi, J.; Onck, P.R.; Poort, G.; Van Keulen, F.

A micromechanical-based approach is proposed to quantify the effective (in the macroscopic sense) elastic constants of Cosserat materials. The material under investigation (cancellous bone) is cellular and classically elastic at the microscopic level and assumed to be dense Cosserat elastic at the

Fibre failure assessment in carbon fibre reinforced polymers under fatigue loading by synchrotron X-ray computed tomography

OpenAIRE

Garcea, Serafina; Sinclair, Ian; Spearing, Simon

2016-01-01

In situ fatigue experiments using synchrotron X-ray computed tomography (SRCT) are used to assess the underpinning micromechanisms of fibre failure in double notch carbon/epoxy coupons. Observations showed fibre breaks along the 0º ply splits, associated with the presence and failure of bridging fibres, as well as fibres failed in the bulk composite within the 0º plies. A tendency for cluster formation, with multiple adjacent breaks in the bulk composite was observed when higher peak loads we...

Micromechanical modelling of nanocrystalline and ultrafine grained metals: A short overview

DEFF Research Database (Denmark)

Mishnaevsky, Leon; Levashov, Evgeny

2015-01-01

An overview of micromechanical models of strength and deformation behaviour of nanostructured and ultrafine grained metallic materials is presented. Composite models of nanomaterials, polycrystal plasticity based models, grain boundary sliding, the effect of non-equilibrium grain boundaries...... and nanoscale properties are discussed and compared. The examples of incorporation of peculiar nanocrystalline effects (like large content of amorphous or semi-amorphous grain boundary phase, partial dislocation GB emission/glide/GB absorption based deformation mechanism, diffusion deformation, etc.......) into the continuum mechanical approach are given. The possibilities of using micromechanical models to explore the ways of the improving the properties of nanocrystalline materials by modifying their structures (e.g., dispersion strengthening, creating non-equilibrium grain boundaries, varying the grain size...

Some failure analyses of South African Air Force aircraft engine and airframe components

CSIR Research Space (South Africa)

Benson, JM

1998-06-01

Full Text Available Failure analyses of various engine and airframe components from South African Air Force aircraft have been performed by the Division of Materials Science and Technology over several years and these have ranged from crash investigations to minor...

Cantilever-like micromechanical sensors

DEFF Research Database (Denmark)

Boisen, Anja; Dohn, Søren; Keller, Stephan Sylvest

2011-01-01

The field of cantilever-based sensing emerged in the mid-1990s and is today a well-known technology for label-free sensing which holds promise as a technique for cheap, portable, sensitive and highly parallel analysis systems. The research in sensor realization as well as sensor applications has...... increased significantly over the past 10 years. In this review we will present the basic modes of operation in cantilever-like micromechanical sensors and discuss optical and electrical means for signal transduction. The fundamental processes for realizing miniaturized cantilevers are described with focus...... on silicon-and polymer-based technologies. Examples of recent sensor applications are given covering such diverse fields as drug discovery, food diagnostics, material characterizations and explosives detection....

Ultrafast Hydro-Micromechanical Synthesis of Calcium Zincate: Structural and Morphological Characterizations

Directory of Open Access Journals (Sweden)

Vincent Caldeira

2017-01-01

Full Text Available Calcium zincate is a compound with a large panel of application: mainly known as an advantageous replacement of zinc oxide in negative electrodes for air-zinc or nickel-zinc batteries, it is also used as precursor catalyst in biodiesel synthesis and as antifungal compound for the protection of limestone monuments. However, its synthesis is not optimized yet. In this study, it was elaborated using an ultrafast synthesis protocol: Hydro-Micromechanical Synthesis. Two other synthesis methods, Hydrochemical Synthesis and Hydrothermal Synthesis, were used for comparison. In all cases, the as-synthesized samples were analyzed by X-ray diffraction, scanning electron microscopy, and LASER diffraction particle size analysis. Rietveld method was used to refine various structural parameters and obtain an average crystallite size, on a Hydro-Micromechanical submicronic sample. X-ray single crystal structure determination was performed on a crystal obtained by Hydrochemical Synthesis. It has been shown that regardless of the synthesis protocol, the prepared samples always crystallize in the same crystal lattice, with P21/c space group and only differ from their macroscopic textural parameters. Nevertheless, only the Hydro-Micromechanical method is industrially scalable and enables a precise control of the textural parameters of the obtained calcium zincate.

A Hybrid Approach to Composite Damage and Failure Analysis Combining Synergistic Damage Mechanics and Peridynamics

Science.gov (United States)

2017-03-30

manufacturing defects in the intermediately -homogenized model of fiber-reinforced composites. 15. SUBJECT TERMS Computational micromechanics; Cavitation...defects in the intermediately -homogenized model of fiber-reinforced composites. Task 1.1 Micro-level crack initiation Background and motivation In...new Intermediate Homogenization Peridynamic approach (IH-PD model) for failure in multiphase materials. We plan to apply this IH-PD model for the

Heterogeneous Rock Simulation Using DIP-Micromechanics-Statistical Methods

Directory of Open Access Journals (Sweden)

H. Molladavoodi

2018-01-01

Full Text Available Rock as a natural material is heterogeneous. Rock material consists of minerals, crystals, cement, grains, and microcracks. Each component of rock has a different mechanical behavior under applied loading condition. Therefore, rock component distribution has an important effect on rock mechanical behavior, especially in the postpeak region. In this paper, the rock sample was studied by digital image processing (DIP, micromechanics, and statistical methods. Using image processing, volume fractions of the rock minerals composing the rock sample were evaluated precisely. The mechanical properties of the rock matrix were determined based on upscaling micromechanics. In order to consider the rock heterogeneities effect on mechanical behavior, the heterogeneity index was calculated in a framework of statistical method. A Weibull distribution function was fitted to the Young modulus distribution of minerals. Finally, statistical and Mohr–Coulomb strain-softening models were used simultaneously as a constitutive model in DEM code. The acoustic emission, strain energy release, and the effect of rock heterogeneities on the postpeak behavior process were investigated. The numerical results are in good agreement with experimental data.

Effect of the primary particle morphology on the micromechanical properties of nanostructured alumina agglomerates

International Nuclear Information System (INIS)

Schilde, Carsten; Westphal, Bastian; Kwade, Arno

2012-01-01

Depending on the application of nanoparticles, certain characteristics of the product quality such as size, morphology, abrasion resistance, specific surface, dispersibility and tendency to agglomeration are important. These characteristics are a function of the physicochemical properties, i.e. the micromechanical properties of the nanostructured material. The micromechanical properties of these nanostructured agglomerates such as the maximum indentation force, the plastic and elastic deformation energy and the strength give information on the product properties, e.g. the efficiency of a dispersion process of the agglomerates, and can be measured by nanoindentation. In this study a Berkovich indenter tip was used for the characterisation of model aggregates out of sol–gel produced silica and precipitated alumina agglomerates with different primary particle morphologies (dimension of 15–40 nm). In general, the effect of the primary particle morphology and the presence or absence of solid bonds can be characterised by the measurement of the micromechanical properties via nanoindentation. The micromechanical behaviour of aggregates containing solid bonds is strongly affected by the elastic–plastic deformation behaviour of the solid bonds and the breakage of solid bonds. Moreover, varying the primary particle morphology for similar particle material and approximately isotropic agglomerate behaviour the particle–particle interactions within the agglomerates can be described by the elementar breaking stress according to the formula of Rumpf.

A micromechanical study of the damage mechanics of acrylic particulate composites under thermomechanical loading

Science.gov (United States)

Nie, Shihua

The main aim of this dissertation was to characterize the damage mechanism and fatigue behavior of the acrylic particulate composite. This dissertation also investigated how the failure mechanism is influenced by changes in certain parameters including the volume fraction of particle, the interfacial bonding strength, the stiffness and thickness of the interphase, and the CTE mismatch between the particle and the matrix. Monotonic uniaxial tensile and compressive testing under various temperatures and strain rates, isothermal low-cycle mechanical testing and thermal cycling of a plate with a cutout were performed. The influence of the interfacial bonding strength between the particle and the matrix on the failure mechanism of the ATH filled PMMA was investigated using in situ observations under uniaxial loading conditions. For composites with weak interfacial bonding, the debonding is the major damage mode. For composites with strong interfacial bonding, the breakage of the agglomerate of particles is the major damage mode. Experimental studies also demonstrated the significant influence of interfacial bonding strength on the fatigue life of the ATH filled PMMA. The damage was characterized in terms of the elastic modulus degradation, the load-drop parameter, the plastic strain range and the hysteresis dissipation. Identifying the internal state variables that quantify material degradation under thermomechanical loading is an active research field. In this dissertation, the entropy production, which is a measure of the irreversibility of the thermodynamic system, is used as the metric for damage. The close correlation between the damage measured in terms of elastic modulus degradation and that obtained from the finite element simulation results validates the entropy based damage evolution function. A micromechanical model for acrylic particulate composites with imperfect interfacial bonds was proposed. Acrylic particulate composites are treated as three

Micromechanical modeling and inverse identification of damage using cohesive approaches

International Nuclear Information System (INIS)

Blal, Nawfal

2013-01-01

In this study a micromechanical model is proposed for a collection of cohesive zone models embedded between two each elements of a standard cohesive-volumetric finite element method. An equivalent 'matrix-inclusions' composite is proposed as a representation of the cohesive-volumetric discretization. The overall behaviour is obtained using homogenization approaches (Hashin Shtrikman scheme and the P. Ponte Castaneda approach). The derived model deals with elastic, brittle and ductile materials. It is available whatever the triaxiality loading rate and the shape of the cohesive law, and leads to direct relationships between the overall material properties and the local cohesive parameters and the mesh density. First, rigorous bounds on the normal and tangential cohesive stiffnesses are obtained leading to a suitable control of the inherent artificial elastic loss induced by intrinsic cohesive models. Second, theoretical criteria on damageable and ductile cohesive parameters are established (cohesive peak stress, critical separation, cohesive failure energy,... ). These criteria allow a practical calibration of the cohesive zone parameters as function of the overall material properties and the mesh length. The main interest of such calibration is its promising capacity to lead to a mesh-insensitive overall response in surface damage. (author) [fr

Continuum and micro-mechanics treatment of constraint in fracture

International Nuclear Information System (INIS)

Dodds, R.H. Jr.; Shih, C.F.

1993-01-01

This paper explores the fundamental concepts of the J-Q description of crack-tip fields, the fracture toughness locus and micromechanics approaches to predict the variability of macroscopic fracture toughness with constraint under elastic-plastic conditions. While these concepts derived from plane-strain considerations, initial applications in fully 3-D geometries are very promising. Computational results are presented for a surface cracked plate containing a 6:1 semi-elliptical, a=t/4 flaw subjected to remote uniaxial and biaxial tension. Crack-tip stress fields consistent with the J-Q theory are demonstrated to exist at each location along the crack front. The micromechanics model employs the J-Q description of crack-front stresses to interpret fracture toughness values measured on laboratory specimens for fracture assessment of the surface cracked plate. The computational results suggest only a minor effect of the biaxial loading on the crack tip stress fields and, consequently, on the propensity for fracture relative to the uniaxial loading. 45 refs., 19 figs., 3 tabs

Micromechanical investigation of sand migration in gas hydrate-bearing sediments

Science.gov (United States)

Uchida, S.; Klar, A.; Cohen, E.

2017-12-01

Past field gas production tests from hydrate bearing sediments have indicated that sand migration is an important phenomenon that needs to be considered for successful long-term gas production. The authors previously developed the continuum based analytical thermo-hydro-mechanical sand migration model that can be applied to predict wellbore responses during gas production. However, the model parameters involved in the model still needs to be calibrated and studied thoroughly and it still remains a challenge to conduct well-defined laboratory experiments of sand migration, especially in hydrate-bearing sediments. Taking the advantage of capability of micromechanical modelling approach through discrete element method (DEM), this work presents a first step towards quantifying one of the model parameters that governs stresses reduction due to grain detachment. Grains represented by DEM particles are randomly removed from an isotropically loaded DEM specimen and statistical analyses reveal that linear proportionality exists between the normalized volume of detached solids and normalized reduced stresses. The DEM specimen with different porosities (different packing densities) are also considered and statistical analyses show that there is a clear transition between loose sand behavior and dense sand behavior, characterized by the relative density.

Micromechanical Modeling of Solid Oxide Fuel Cell Anode Supports based on Three-dimensional Reconstructions

DEFF Research Database (Denmark)

Kwok, Kawai; Jørgensen, Peter Stanley; Frandsen, Henrik Lund

2014-01-01

Ni-3YSZ in the operating temperature through numerical micromechanical modeling. Three-dimensional microstructures of Ni-3YSZ anode supports are reconstructed from a two-dimensional image stack obtained via focused ion beam tomography. Time-dependent stress distributions in the microscopic scale...... are computed by the finite element method. The macroscopic creep response of the porous anode support is determined based on homogenization theory. It is shown that micromechanical modeling provides an effective tool to study the effect of microstructures on the macroscopic properties....

Micromechanical model of lung parenchyma hyperelasticity

Science.gov (United States)

Concha, Felipe; Sarabia-Vallejos, Mauricio; Hurtado, Daniel E.

2018-03-01

Mechanics plays a key role in respiratory physiology, as lung tissue cyclically deforms to bring air in and out the lung, a life-long process necessary for respiration. The study of regional mechanisms of deformation in lung parenchyma has received great attention to date due to its clinical relevance, as local overstretching and stress concentration in lung tissue is currently associated to pathological conditions such as lung injury during mechanical ventilation therapy. This mechanical approach to lung physiology has motivated the development of constitutive models to better understand the relation between stress and deformation in the lung. While material models proposed to date have been key in the development of whole-lung simulations, either they do not directly relate microstructural properties of alveolar tissue with coarse-scale behavior, or they require a high computational effort when based on real alveolar geometries. Furthermore, most models proposed to date have not been thoroughly validated for anisotropic deformation states, which are commonly found in normal lungs in-vivo. In this work, we develop a novel micromechanical model of lung parenchyma hyperelasticity using the framework of finite-deformation homogenization. To this end, we consider a tetrakaidecahedron unit cell with incompressible Neo-Hookean structural elements that account for the alveolar wall tissue responsible for the elastic response, and derive expressions for its effective coarse-scale behavior that directly depend on the alveolar wall elasticity, reference porosity, and two other geometrical coefficients. To validate the proposed model, we simulate the non-linear elastic response of twelve representative volume elements (RVEs) of lung parenchyma with micrometric dimensions, whose geometry is obtained from micrometric computed-tomography reconstructions of murine lungs. We show that the proposed micromechanical model accurately captures the RVEs response not only for isotropic

Micromechanical modeling of short glass-fiber reinforced thermoplastics-Isotropic damage of pseudograins

International Nuclear Information System (INIS)

Kammoun, S.; Brassart, L.; Doghri, I.; Delannay, L.; Robert, G.

2011-01-01

A micromechanical damage modeling approach is presented to predict the overall elasto-plastic behavior and damage evolution in short fiber reinforced composite materials. The practical use of the approach is for injection molded thermoplastic parts reinforced with short glass fibers. The modeling is proceeded as follows. The representative volume element is decomposed into a set of pseudograins, the damage of which affects progressively the overall stiffness and strength up to total failure. Each pseudograin is a two-phase composite with aligned inclusions having same aspect ratio. A two-step mean-field homogenization procedure is adopted. In the first step, the pseudograins are homogenized individually according to the Mori-Tanaka scheme. The second step consists in a self-consistent homogenization of homogenized pseudograins. An isotropic damage model is applied at the pseudograin level. The model is implemented as a UMAT in the finite element code ABAQUS. Model is shown to reproduce the strength and the anisotropy (Lankford coefficient) during uniaxial tensile tests on samples cut under different directions relative to the injection flow direction.

Readout of micromechanical cantilever sensor arrays by Fabry-Perot interferometry

International Nuclear Information System (INIS)

Wehrmeister, Jana; Fuss, Achim; Saurenbach, Frank; Berger, Ruediger; Helm, Mark

2007-01-01

The increasing use of micromechanical cantilevers in sensing applications causes a need for reliable readout techniques of micromechanical cantilever sensor (MCS) bending. Current optical beam deflection techniques suffer from drawbacks such as artifacts due to changes in the refraction index upon exchange of media. Here, an adaptation of the Fabry-Perot interferometer is presented that allows simultaneous determination of MCS bending and changes in the refraction index of media. Calibration of the instrument with liquids of known refraction index provides an avenue to direct measurement of bending with nanometer precision. Versatile construction of flow cells in combination with alignment features for substrate chips allows simultaneous measurement of two MCS situated either on the same, or on two different support chips. The performance of the instrument is demonstrate in several sensing applications, including adsorption experiments of alkanethioles on MCS gold surfaces, and measurement of humidity changes in air

Micromechanical exfoliation of two-dimensional materials by a polymeric stamp

International Nuclear Information System (INIS)

Costa, M C Ferraz da; Ribeiro, H B; Kessler, F; Souza, E A T de; Fechine, G J M

2016-01-01

In this work, an alternative technique to the traditional micromechanical exfoliation of two-dimensional materials is proposed, consisting of isolated flakes of graphite and molybdenum disulphide onto polymeric surfaces films. The set made up of polymer and flakes is fabricated by using a hot-press machine called polymeric stamp. The polymeric stamp was used to allocate flakes and also to allow the exfoliation process to take place just in one face of isolated flake. Optical microscopy, Raman spectroscopy and photoluminescence spectroscopy results showed that multilayers, bilayers and single layers of graphene and MoS 2 were obtained by using a polymeric stamp as tool for micromechanical exfoliation. These crystals were more easily found because the exfoliation process concentrates them in well-defined locations. The results prove the effectiveness of the method by embedding two-dimensional materials into polymers to fabricate fewer layers crystals in a fast, economic and clean way. (paper)

Micromechanical exfoliation of two-dimensional materials by a polymeric stamp

Science.gov (United States)

Ferraz da Costa, M. C.; Ribeiro, H. B.; Kessler, F.; de Souza, E. A. T.; Fechine, G. J. M.

2016-02-01

In this work, an alternative technique to the traditional micromechanical exfoliation of two-dimensional materials is proposed, consisting of isolated flakes of graphite and molybdenum disulphide onto polymeric surfaces films. The set made up of polymer and flakes is fabricated by using a hot-press machine called polymeric stamp. The polymeric stamp was used to allocate flakes and also to allow the exfoliation process to take place just in one face of isolated flake. Optical microscopy, Raman spectroscopy and photoluminescence spectroscopy results showed that multilayers, bilayers and single layers of graphene and MoS2 were obtained by using a polymeric stamp as tool for micromechanical exfoliation. These crystals were more easily found because the exfoliation process concentrates them in well-defined locations. The results prove the effectiveness of the method by embedding two-dimensional materials into polymers to fabricate fewer layers crystals in a fast, economic and clean way.

An integrated micromechanical large particle in flow sorter (MILPIS)

Science.gov (United States)

Fuad, Nurul M.; Skommer, Joanna; Friedrich, Timo; Kaslin, Jan; Wlodkowic, Donald

2015-06-01

At present, the major hurdle to widespread deployment of zebrafish embryo and larvae in large-scale drug development projects is lack of enabling high-throughput analytical platforms. In order to spearhead drug discovery with the use of zebrafish as a model, platforms need to integrate automated pre-test sorting of organisms (to ensure quality control and standardization) and their in-test positioning (suitable for high-content imaging) with modules for flexible drug delivery. The major obstacle hampering sorting of millimetre sized particles such as zebrafish embryos on chip-based devices is their substantial diameter (above one millimetre), mass (above one milligram), which both lead to rapid gravitational-induced sedimentation and high inertial forces. Manual procedures associated with sorting hundreds of embryos are very monotonous and as such prone to significant analytical errors due to operator's fatigue. In this work, we present an innovative design of a micromechanical large particle in-flow sorter (MILPIS) capable of analysing, sorting and dispensing living zebrafish embryos for drug discovery applications. The system consisted of a microfluidic network, revolving micromechanical receptacle actuated by robotic servomotor and opto-electronic sensing module. The prototypes were fabricated in poly(methyl methacrylate) (PMMA) transparent thermoplastic using infrared laser micromachining. Elements of MILPIS were also fabricated in an optically transparent VisiJet resin using 3D stereolithography (SLA) processes (ProJet 7000HD, 3D Systems). The device operation was based on a rapidly revolving miniaturized mechanical receptacle. The latter function was to hold and position individual fish embryos for (i) interrogation, (ii) sorting decision-making and (iii) physical sorting..The system was designed to separate between fertilized (LIVE) and non-fertilized (DEAD) eggs, based on optical transparency using infrared (IR) emitters and receivers embedded in the system

Micromechanics of intergranular creep failure under cyclic loading

DEFF Research Database (Denmark)

van der Giessen, Erik; Tvergaard, Viggo

1996-01-01

boundaries are modelled individually. The model incorporates power-law creep of the grains, viscous grain boundary sliding between grains as well as the nucleation and growth of grain boundary cavities until they coalesce and form microcracks. Study of a limiting case with a facet-size microcrack reveals....... The analyses provide some new understanding that helps to explain the sometimes peculiar behaviour under balanced cyclic creep. Copyright (C) 1996 Acta Metallurgica Inc....

Micromechanics and Microactuators : Proceedings of MAMM 2010

CERN Document Server

Corves, Burkhard; Petuya, Victor

2012-01-01

This book contains selected papers presented at MAMM 2010, the First Workshop on Microactuators and Micromechanisms. This workshop has brought together scientists, industry experts and students and has provided a special opportunity for know-how exchange and collaboration in various disciplines referring to microsystems technology. The conference was organized by the Technical Committees of Mechanical Transmissions and Micromachines under the patronage of IFToMM, the International Federation for the Promotion of Mechanism and Machine Science.

Some micromechanical models of elastoplastic behaviors of porous geomaterials

Directory of Open Access Journals (Sweden)

W.Q. Shen

2017-02-01

Full Text Available Some micromechanics-based constitutive models are presented in this study for porous geomaterials. These micro-macro mechanical models focus on the effect of porosity and the inclusions on the macroscopic elastoplastic behaviors of porous materials. In order to consider the effect of pores and the compressibility of the matrix, some macroscopic criteria are presented firstly for ductile porous medium having one population of pores with different types of matrix (von Mises, Green type, Mises–Schleicher and Drucker–Prager. Based on different homogenization techniques, these models are extended to the double porous materials with two populations of pores at different scales and a Drucker–Prager solid phase at the microscale. Based on these macroscopic criteria, complete constitutive models are formulated and implemented to describe the overall responses of typical porous geomaterials (sandstone, porous chalk and argillite. Comparisons between the numerical predictions and experimental data with different confining pressures or different mineralogical composites show the capabilities of these micromechanics-based models, which take into account the effects of microstructure on the macroscopic behavior and significantly improve the phenomenological ones.

Time dependent micromechanics in continuous graphite fiber/epoxy composites with fiber breaks

Science.gov (United States)

Zhou, Chao Hui

Time dependent micromechanics in graphite fiber/epoxy composites around fiber breaks was investigated with micro Raman spectroscopy (MRS) and two shear-lag based composite models, a multi-fiber model (VBI) and a single fiber model (SFM), which aim at predicting the strain/stress evolutions in the composite from the matrix creep behavior and fiber strength statistics. This work is motivated by the need to understand the micromechanics and predict the creep-rupture of the composites. Creep of the unfilled epoxy was characterized under different stress levels and at temperatures up to 80°C, with two power law functions, which provided the modeling parameters used as input for the composite models. Both the VBI and the SFM models showed good agreement with the experimental data obtained with MRS, when inelasticity (interfacial debonding and/or matrix yielding) was not significant. The maximum shear stress near a fiber break relaxed at t-alpha/2 (or as (1+ talpha)-1/2) and the load recovery length increased at talpha/2(or (1+ talpha)1/2) following the model predictions. When the inelastic zone became non-negligible, the viscoelastic VBI model lost its competence, while the SFM with inelasticity showed good agreement with the MRS measurements. Instead of using the real fiber spacing, an effective fiber spacing was used in model predictions, taking into account of the radial decay of the interfacial shear stress from the fiber surface. The comparisons between MRS data and the SFM showed that inelastic zone would initiate when the shear strain at the fiber end exceeds a critical value gammac which was determined to be 5% for this composite system at room temperature and possibly a smaller value at elevated temperatures. The stress concentrations in neighboring intact fibers played important roles in the subsequent fiber failure and damage growth. The VBI model predicts a constant stress concentration factor, 1.33, for the 1st nearest intact fiber, which is in good

Micromechanical modeling of the cement-bone interface: the effect of friction, morphology and material properties on the micromechanical response

OpenAIRE

Janssen, Dennis; Mann, Kenneth A.; Verdonschot, Nico

2008-01-01

In order to gain insight into the micro-mechanical behavior of the cement-bone interface, the effect of parametric variations of frictional, morphological and material properties on the mechanical response of the cement-bone interface were analyzed using a finite element approach. Finite element models of a cement-bone interface specimen were created from micro-computed tomography data of a physical specimen that was sectioned from an in vitro cemented total hip arthroplasty. In five models t...

Computational methods for coupling microstructural and micromechanical materials response simulations

Energy Technology Data Exchange (ETDEWEB)

HOLM,ELIZABETH A.; BATTAILE,CORBETT C.; BUCHHEIT,THOMAS E.; FANG,HUEI ELIOT; RINTOUL,MARK DANIEL; VEDULA,VENKATA R.; GLASS,S. JILL; KNOROVSKY,GERALD A.; NEILSEN,MICHAEL K.; WELLMAN,GERALD W.; SULSKY,DEBORAH; SHEN,YU-LIN; SCHREYER,H. BUCK

2000-04-01

Computational materials simulations have traditionally focused on individual phenomena: grain growth, crack propagation, plastic flow, etc. However, real materials behavior results from a complex interplay between phenomena. In this project, the authors explored methods for coupling mesoscale simulations of microstructural evolution and micromechanical response. In one case, massively parallel (MP) simulations for grain evolution and microcracking in alumina stronglink materials were dynamically coupled. In the other, codes for domain coarsening and plastic deformation in CuSi braze alloys were iteratively linked. this program provided the first comparison of two promising ways to integrate mesoscale computer codes. Coupled microstructural/micromechanical codes were applied to experimentally observed microstructures for the first time. In addition to the coupled codes, this project developed a suite of new computational capabilities (PARGRAIN, GLAD, OOF, MPM, polycrystal plasticity, front tracking). The problem of plasticity length scale in continuum calculations was recognized and a solution strategy was developed. The simulations were experimentally validated on stockpile materials.

Nanostructured interfaces for enhancing mechanical properties of composites: Computational micromechanical studies

DEFF Research Database (Denmark)

Mishnaevsky, Leon

2015-01-01

Computational micromechanical studies of the effect of nanostructuring and nanoengineering of interfaces, phase and grain boundaries of materials on the mechanical properties and strength of materials and the potential of interface nanostructuring to enhance the materials properties are reviewed....

Micromechanical modeling of the elasto-viscoplastic bahavior of semi-crystalline polymers

NARCIS (Netherlands)

Dommelen, van J.A.W.; Parks, D.M.; Boyce, M.C.; Brekelmans, W.A.M.; Baaijens, F.P.T.

2003-01-01

A micromechanically-based constitutive model for the elasto-viscoplastic deformationand texture evolution of semi-crystalline polymers is developed. The modelidealizes the microstructure to consist of an aggregate of two-phase layered compositeinclusions. A new framework for the composite inclusion

Micromechanics Based Inelastic and Damage Modeling of Composites

Directory of Open Access Journals (Sweden)

P. P. Procházka

2004-01-01

Full Text Available Micromechanics based models are considered for application to viscoelasticity and damage in metal matrix composites. The method proposes a continuation and development of Dvooák’s transformation field analysis, considering the piecewise uniform eigenstrains in each material phase. Standard applications of the method to a two-phase are considered in this study model, i.e., only one sub-volume per phase is considered. A continuous model is used, employing transformation field analysis with softening in order to prevent the tensile stress overstepping the tensile strength. At the same time shear cracking occurs in the tangential direction of the possible crack. This is considered in the principal shear stresses and they make disconnections in displacements. In this case, discontinuous models are more promising. Because discrete models, that can describe the situation more realistically have not been worked out in detail, we retain a continuous model and substitute the slip caused by overstepping the damage law by introducing eigenparameters from TFA. The various aspects of the proposed methods are systematically checked by comparing with finite element unit cell analyses, made through periodic homogenization assumptions, for SiC/Ti unidirectional lay-ups. 

Ultrasensitive thermometer for atmospheric pressure operation based on a micromechanical resonator

DEFF Research Database (Denmark)

Cagliani, Alberto; Pini, V.; Tamayo, J.

2014-01-01

For highly integrated systems for bio and chemical analysis a precise and integrated measurement of temperature is of fundamental importance. We have developed an ultrasensitive thermometer based on a micromechanical resonator for operation in air. The high quality factor and the strong temperatu...

Composite materials for wind energy applications: micromechanical modeling and future directions

DEFF Research Database (Denmark)

Mishnaevsky, Leon

2012-01-01

The strength and reliability of wind turbine blades depend on the properties, mechanical behavior and strengths of the material components (glass or carbon fibers and polymer matrix), and the interaction between them under loading. In this paper, ideas, methods and concepts of micromechanical...

Fully coupled heat conduction and deformation analyses of nonlinear viscoelastic composites

KAUST Repository

Khan, Kamran

2012-05-01

This study presents an integrated micromechanical model-finite element framework for analyzing coupled heat conduction and deformations of particle-reinforced composite structures. A simplified micromechanical model consisting of four sub-cells, i.e., one particle and three matrix sub-cells is formulated to obtain the effective thermomechanical properties and micro-macro field variables due to coupled heat conduction and nonlinear thermoviscoelastic deformation of a particulate composite that takes into account the dissipation of energy from the viscoelastic constituents. A time integration algorithm for simultaneously solving the equations that govern heat conduction and thermoviscoelastic deformations of isotropic homogeneous materials is developed. The algorithm is then integrated to the proposed micromechanical model. A significant temperature generation due to the dissipation effect in the viscoelastic matrix was observed when the composite body is subjected to cyclic mechanical loadings. Heat conduction due to the dissipation of the energy cannot be ignored in predicting the factual temperature and deformation fields within the composite structure, subjected to cyclic loading for a long period. A higher creep resistant matrix material or adding elastic particles can lower the temperature generation. Our analyses suggest that using particulate composites and functionally graded materials can reduce the heat generation due to energy dissipation. © 2012 Elsevier Ltd.

EDITORIAL: 15th European Workshop on Micromechanics (MME)

Science.gov (United States)

Puers, Bob

2005-07-01

This special issue of Journal of Micromechanics and Microengineering is entirely devoted to the fifteenth European Workshop on Micromechanics (MME), which was held in Leuven, at the Faculty Club, 5-7 September 2004. In this issue you will find a selection of papers presented at this workshop. The MME Workshop is organized every year to gather mostly European scientists and people from industry to discuss topics related to micromachining and microengineering in an informal manner. The first workshop was held at Twente University, the Netherlands, in 1989. The success of that event inaugurated a series of workshops traveling all over Europe. Looking back on the fifteen years of micromachining it is evident that the field has become more mature. More application driven research is now replacing the basic pure technology driven research we once got so excited about. Yet, half of the contributions still cover problems related to fabrication, production and reliability. Traditionally, the workshop aims to bring together young scientists in the field, with emphasis on discussions and communications in a friendly and informal atmosphere. The goal is to stimulate and to improve knowledge in the field, as well as to promote friendships between researchers. This edition of the workshop was no different. More than 70 papers were contributed, and it was decided to widen the scope with contributions also covering non-silicon technologies. This trend had already been informally introduced some years ago. After the third edition, it was decided to open up a selection of the contributed papers to a broader public by publishing them in a special issue of Journal of Micromechanics and Microengineering, and this has continued to the present day. Since the purpose of the workshop clearly is to stimulate younger scientists to enter the field, even immature research is presented there. The selection in this issue, however, aims to bring to you the more advanced level research work. Even

Cryogenic transimpedance amplifier for micromechanical capacitive sensors.

Science.gov (United States)

Antonio, D; Pastoriza, H; Julián, P; Mandolesi, P

2008-08-01

We developed a cryogenic transimpedance amplifier that works at a broad range of temperatures, from room temperature down to 4 K. The device was realized with a standard complementary metal oxide semiconductor 1.5 mum process. Measurements of current-voltage characteristics, open-loop gain, input referred noise current, and power consumption are presented as a function of temperature. The transimpedance amplifier has been successfully applied to sense the motion of a polysilicon micromechanical oscillator at low temperatures. The whole device is intended to serve as a magnetometer for microscopic superconducting samples.

Failure analyses and weld repair of boiler feed water pumps

Energy Technology Data Exchange (ETDEWEB)

Vulpen, R van [KemaPower Generation, Arnhem (Netherlands)

1999-12-31

During a regular inspection of the Boiler Auxiliaries at one of the Dutch Electricity Production Companies serious cracks were found in the cover and casings of the feed water circulation pumps in two units after 108.000 and 122.000 hours of boiler operation. Kema Laboratories carried out Failure analyses on boat samples at the cracked areas. Corrosion fatigue cracking was found on the inner side of the GS-24CrNiMo325 casing. Shop Weld repairs were carried out using a newly developed mechanized Plasma Welding Technique. The repaired feed water circulation pumps showed no problems alter several years of operation. The costs of repair were substantially lower than the costs of replacement. (orig.) 3 refs.

Failure analyses and weld repair of boiler feed water pumps

Energy Technology Data Exchange (ETDEWEB)

Vulpen, R. van [KemaPower Generation, Arnhem (Netherlands)

1998-12-31

During a regular inspection of the Boiler Auxiliaries at one of the Dutch Electricity Production Companies serious cracks were found in the cover and casings of the feed water circulation pumps in two units after 108.000 and 122.000 hours of boiler operation. Kema Laboratories carried out Failure analyses on boat samples at the cracked areas. Corrosion fatigue cracking was found on the inner side of the GS-24CrNiMo325 casing. Shop Weld repairs were carried out using a newly developed mechanized Plasma Welding Technique. The repaired feed water circulation pumps showed no problems alter several years of operation. The costs of repair were substantially lower than the costs of replacement. (orig.) 3 refs.

Experiment feedbacks in micromechanics modeling of thermomechanical behaviors of SMA polycrystals

International Nuclear Information System (INIS)

Sittner, P.; Novak, V.

2004-01-01

Simulations of pseudoelastic deformation of NiTi and CuAlZnMn polycrystals using an earlier developed micromechanics model are presented. Advantages of having multiple feedbacks established between the model and in situ neutron diffraction experiment as well as doing modeling and experimentation simultaneously are discussed

Three-dimensional microstructure-based micromechanical modeling for TC6 titanium alloy

Energy Technology Data Exchange (ETDEWEB)

Li, Guoju; Shi, Ran [School of Materials Science and Engineering, Beijing Institute of Technology, Beijing 100081 (China); National Key Laboratory of Science and Technology on Materials Under Shock and Impact, Beijing 100081 (China); Fan, Qunbo, E-mail: fanqunbo@bit.edu.cn [School of Materials Science and Engineering, Beijing Institute of Technology, Beijing 100081 (China); National Key Laboratory of Science and Technology on Materials Under Shock and Impact, Beijing 100081 (China); Xia, Yumeng; Zhang, Hongmei [School of Materials Science and Engineering, Beijing Institute of Technology, Beijing 100081 (China); National Key Laboratory of Science and Technology on Materials Under Shock and Impact, Beijing 100081 (China)

2017-02-08

A new in-depth evaluation of the micromechanical response of TC6 (Ti–6Al–1.5Cr–2.5Mo–0.5Fe–0.3Si) titanium alloy subjected to uniaxial tensile loading is performed based on micromechanical modeling. This evaluation includes reconstruction of the three-dimensional annealed microstructure (annealing at 800 °C for 2 h, then air cooled) of the alloy via dual-energy micro-computed tomography. In addition, constitutive relations of the constituent phases were determined via synchrotron-based in-situ high-energy X-ray diffraction and a self-consistent model as well as nanoindentation tests combined with finite element modeling. The results revealed that the stress concentration was translated from the primary α phase to the secondary α phase, then to the β phase. Moreover, the stress generated was re-transferred to the primary α phase when the strain was increased from 0.00 to 0.05. This transfer is indicative of crack initiation in the primary α grains.

Micromechanical simulation of frictional behaviour in metal forming

International Nuclear Information System (INIS)

Zhang, S.; Hodgson, P.D.; Cardew-Hall, M.J.; Kalyanasundaram, S.

2000-01-01

Friction is a critical factor for Sheet Metal Forming (SMF). The Coulomb friction model is usually used in most Finite Element (FE) simulation for SMF. However, friction is a function of the local contact deformation conditions, such as local pressure, roughness and relative velocity. This paper will present a micromechanical model that accounts for the local frictional behaviour through finite element simulations performed at the micromechanical level. Frictional behaviour between contact surfaces can be based on three cases: boundary, hydrodynamic and mixed lubrication. In our microscopic friction model based on FEM, the case of boundary lubrication contact between sheet and tool has been considered. In the view of microscopic geometry, roughness depends upon amplitude and wavelength of surface asperities of sheet and tool. The mean pressure applied on the surface differs from the pressure over the actual contact area. The effect of roughness (microscopic geometric condition) and relative speed of contact surfaces on friction coefficient was examined in the FE model for the microscopic friction behaviour. The analysis was performed using an explicit finite element formulation. In this study, it was found that the roughness of deformable sheet decreases during sliding and the coefficient of friction increases with increasing roughness of contact surfaces. The coefficient of friction increases with the increase of relative velocity and adhesive friction coefficient between contact surfaces. (author)

Applying micromechanic failure models for description of failure modes in the ductile-brittle transition region; Einsatz mikromechanischer Schaedigungsmodelle im sproed-duktilen Uebergangsbereich

Energy Technology Data Exchange (ETDEWEB)

Bernauer, G.

1997-07-01

The work reported was to examine whether the modified Gurson model and the Beremin model can be applied to the brittle-ductile transition region of a ferritic steel, and whether the material`s behaviour can be characterized with a failure model integrating the two models mentioned above into one. Any possible improvements of this approach were to be found. The report at first gives a brief list of terminology and formulas used. Chapter 3 explains the microscopic processes typically observed in the transition region in connection with the failure modes of ductile fracture and cleavage fracture, and shows possible approaches for modelling. Chapter 4 defines the specimens and materials, and chapter 5 explains the experiments as well as the microscopic analyses of the fracture surfaces. Chapter 6 presents subsequent calculations representing the processes observed. Based on the stress distributions thus derived, the Beremin model is re-examined for further development. Chapter 7 summarizes the results obtained. (orig./CB) [Deutsch] Ziel der Arbeit ist, zu untersuchen, ob das modifizierte Gurson-Modell und das Beremin-Modell im sproed-duktilen Uebergangsbereich eines ferritischen Stahls einsetzbar sind und ob das Werkstoffverhalten mit einem aus beiden Modellen kombinierten Schaedigungsmodell berechnet werden kann. Gegebenenfalls sind Verbesserungen herbeizufuehren. Die vorliegende Arbeit beginnt mit einer kurzen Einfuehrung der verwendeten Begriffe und Formalismen. In Kap. 3 werden die mikroskopischen Vorgaenge bei den im Uebergangsbereich typischerweise auftretenden Versagensarten duktiler Bruch und Spaltbruch vorgestellt und verschiedene Moeglichkeiten ihrer Modellierung aufgezeigt. Nach der Vorstellung des Probenwerkstoffs werden in Kap. 4 die Experimente beschrieben und die mikroskopischen Untersuchungen der Bruchflaechen in Kap. 5 dargestellt. Die Nachrechnungen der Experimente werden in Kap. 6 vorgestellt. Auf der Grundlage der dadurch bereitgestellten

Micromechanical models to guide the development of synthetic 'brick and mortar' composites

NARCIS (Netherlands)

Begley, M.R.; Philips, N.R.; Compton, B.G.; Wilbrink, D.V.; Ritchie, R.O.; Utz, M.

2012-01-01

This paper describes a micromechanical analysis of the uniaxial response of composites comprising elastic platelets (bricks) bonded together with thin elastic perfectly plastic layers (mortar). The model yields closed-form results for the spatial variation of displacements in the bricks as a

Pearlitic ductile cast iron: damaging micromechanisms at crack tip

Directory of Open Access Journals (Sweden)

F. Iacoviello

2013-07-01

Full Text Available Ductile cast irons (DCIs are characterized by a wide range of mechanical properties, mainly depending on microstructural factors, as matrix microstructure (characterized by phases volume fraction, grains size and grain distribution, graphite nodules (characterized by size, shape, density and distribution and defects presence (e.g., porosity, inclusions, etc.. Versatility and higher performances at lower cost if compared to steels with analogous performances are the main DCIs advantages. In the last years, the role played by graphite nodules was deeply investigated by means of tensile and fatigue tests, performing scanning electron microscope (SEM observations of specimens lateral surfaces during the tests (“in situ” tests and identifying different damaging micromechanisms.In this work, a pearlitic DCIs fatigue resistance is investigated considering both fatigue crack propagation (by means of Compact Type specimens and according to ASTM E399 standard and overload effects, focusing the interaction between the crack and the investigated DCI microstructure (pearlitic matrix and graphite nodules. On the basis of experimental results, and considering loading conditions and damaging micromechanisms, the applicability of ASTM E399 standard on the characterization of fatigue crack propagation resistance in ferritic DCIs is critically analyzed, mainly focusing the stress intensity factor amplitude role.

Micromechanical modelling of fuel viscoplastic behaviour

International Nuclear Information System (INIS)

Masson, R.; Blanc, V.; Gatt, J.M.; Julien, J.; Michel, B.; Largenton, R.

2015-01-01

To identify the effect of microstructural parameters on the viscoplastic behaviour of nuclear fuels, micromechanical (also called homogenisation) approaches are used. These approaches aim at deriving effective properties of heterogeneous material from the properties of their constituents. They stand on full-field computations of representative volume elements of microstructures as well as on mean-field semi-analytical models. For light water reactor fuels, these approaches have been applied to the modelling of the effect of two microstructural parameters: the porosity effects on the thermal creep of dioxide uranium fuels (transient conditions of irradiation) as well as the plutonium content effect on the viscoplastic behaviour (nominal conditions of irradiations) of mixed oxide fuels (MOX). (authors)

Using Micromechanical Resonators to Measure Rheological Properties and Alcohol Content of Model Solutions and Commercial Beverages

Directory of Open Access Journals (Sweden)

Bart W. Hoogenboom

2012-05-01

Full Text Available Micromechanic resonators provide a small-volume and potentially high-throughput method to determine rheological properties of fluids. Here we explore the accuracy in measuring mass density and viscosity of ethanol-water and glycerol-water model solutions, using a simple and easily implemented model to deduce the hydrodynamic effects on resonating cantilevers of various length-to-width aspect ratios. We next show that these measurements can be extended to determine the alcohol percentage of both model solutions and commercial beverages such as beer, wine and liquor. This demonstrates how micromechanical resonators can be used for quality control of every-day drinks.

Micromechanical Modeling of Grain Boundaries Damage in a Copper Alloy Under Creep

International Nuclear Information System (INIS)

Voese, Markus

2015-01-01

-grained copper-antimony specimens, on the other hand, have been used for the adjustment of the interface model. The calibrated model has finally been used in combination with artificially generated grain structures to investigate influences resulting from numerical and modelling issues. It was found that the mesh size has only a relatively small influence on the macroscopic creep behaviour. But because of the nearly incompressible deformation behaviour of the single crystal model, the use of special purpose continuum element types was necessary to avoid the occurrence of volumetric locking. Also the creep behaviour of polycrystalline materials, which includes the damage development leading to failure, has been analysed for different material and loading parameters. Especially for the copper-antimony alloy under consideration, it becomes evident that the creep behaviour was affected by grain boundary sliding. In particular, stress redistributions at the grain boundaries were comparable to the behaviour of free grain boundary sliding. Furthermore, simulations for multiaxial loading conditions indicated that the damage development is significantly influenced by the maximum principal stress and the von Mises stress.

Contact damage and fracture micromechanisms of multilayered TiN/CrN coatings at micro- and nano-length scales

International Nuclear Information System (INIS)

Roa, J.J.; Jiménez-Piqué, E.; Martínez, R.; Ramírez, G.; Tarragó, J.M.

2014-01-01

In this study, systematic nanomechanical and micromechanical studies have been conducted in three multilayer TiN/CrN systems with different bilayer periods (8, 19 and 25 nm). Additionally, experimental work has been performed on corresponding TiN and CrN single layers, for comparison purposes. The investigation includes the use of different indenter tip geometries as well as contact loading conditions (i.e. indentation/scratch) such to induce different stress field and damage scenarios within the films. The surface and subsurface damage under the different indentation imprints and scratch tracks have been observed by atomic force microscopy, field emission scanning electron microscopy and focused ion beam. Multilayer TiN/CrN coated systems are found to exhibit higher adhesion strength (under sliding contact load) and cracking resistance (under spherical indentation) than those coated with reference TiN and CrN monolayers. The main reason behind these findings is the effective development of microstructurally-driven deformation and cracking resistant micromechanisms: rotation of columnar grains (and associated distortion of bilayer period) and crack deflection of interlayer thickness length scale, respectively. - Highlights: • Nanomechanical and micromechanical study in TiN/CrN systems • TiN/CrN coated systems exhibit higher adhesion strength and cracking resistance. • Main deformation and cracking micromechanisms: columnar grain rotation and crack deflection

Contact damage and fracture micromechanisms of multilayered TiN/CrN coatings at micro- and nano-length scales

Energy Technology Data Exchange (ETDEWEB)

Roa, J.J., E-mail: joan.josep.roa@upc.edu [CIEFMA — Departament de Ciència dels Materials i Eng. Metallúrgica, Universitat Politècnica de Catalunya, Avda. Diagonal 647, 08028 Barcelona (Spain); CRnE, Universitat Politècnica de Catalunya, C. Pasqual i Vila 15, 08028 Barcelona (Spain); Jiménez-Piqué, E. [CIEFMA — Departament de Ciència dels Materials i Eng. Metallúrgica, Universitat Politècnica de Catalunya, Avda. Diagonal 647, 08028 Barcelona (Spain); CRnE, Universitat Politècnica de Catalunya, C. Pasqual i Vila 15, 08028 Barcelona (Spain); Martínez, R. [Centro de Ingeniería Avanzada de Superfícies, Asociación de la Industria Navarra — AIN, Crta. Pamplona, 1, Edificio AIN, 31191 Cordovilla (Spain); Ramírez, G. [CIEFMA — Departament de Ciència dels Materials i Eng. Metallúrgica, Universitat Politècnica de Catalunya, Avda. Diagonal 647, 08028 Barcelona (Spain); Fundació CTM Centre Tecnològic, Avda. Bases de Manresa 1, 08243 Manresa (Spain); Tarragó, J.M. [CIEFMA — Departament de Ciència dels Materials i Eng. Metallúrgica, Universitat Politècnica de Catalunya, Avda. Diagonal 647, 08028 Barcelona (Spain); CRnE, Universitat Politècnica de Catalunya, C. Pasqual i Vila 15, 08028 Barcelona (Spain); and others

2014-11-28

In this study, systematic nanomechanical and micromechanical studies have been conducted in three multilayer TiN/CrN systems with different bilayer periods (8, 19 and 25 nm). Additionally, experimental work has been performed on corresponding TiN and CrN single layers, for comparison purposes. The investigation includes the use of different indenter tip geometries as well as contact loading conditions (i.e. indentation/scratch) such to induce different stress field and damage scenarios within the films. The surface and subsurface damage under the different indentation imprints and scratch tracks have been observed by atomic force microscopy, field emission scanning electron microscopy and focused ion beam. Multilayer TiN/CrN coated systems are found to exhibit higher adhesion strength (under sliding contact load) and cracking resistance (under spherical indentation) than those coated with reference TiN and CrN monolayers. The main reason behind these findings is the effective development of microstructurally-driven deformation and cracking resistant micromechanisms: rotation of columnar grains (and associated distortion of bilayer period) and crack deflection of interlayer thickness length scale, respectively. - Highlights: • Nanomechanical and micromechanical study in TiN/CrN systems • TiN/CrN coated systems exhibit higher adhesion strength and cracking resistance. • Main deformation and cracking micromechanisms: columnar grain rotation and crack deflection.

Micromechanical definition of an entropy for quasi-static deformation of granular materials

NARCIS (Netherlands)

Rothenburg, L.; Kruyt, Nicolaas P.

2009-01-01

A micromechanical theory is formulated for quasi-static deformation of granular materials, which is based on information theory. A reasoning is presented that leads to the definition of an information entropy that is appropriate for quasi-static deformation of granular materials. This definition is

Analysis of cement-treated clay behavior by micromechanical approach

OpenAIRE

Zhang , Dong-Mei; Yin , Zhenyu; Hicher , Pierre Yves; Huang , Hong-Wei

2013-01-01

International audience; Experimental results show the significant influence of cement content on the mechanical properties of cement-treated clays. Cementation is produced by mixing a certain amount of cement with the saturated clay. The purpose of this paper is to model the cementation effect on the mechanical behavior of cement-treated clay. A micromechanical stress-strain model is developed considering explicitly the cementation at inter-cluster contacts. The inter-cluster bonding and debo...

Influence of ceramic thickness and type on micromechanical properties of light-cured adhesive bonding agents.

Science.gov (United States)

Öztürk, Elif; Bolay, Sükran; Hickel, Reinhard; Ilie, Nicoleta

2014-10-01

The aim of this study was to evaluate the micromechanical properties of different adhesive bonding agents when polymerized through ceramics. Sixty sound extracted human third molars were selected and the crowns were sectioned perpendicular to the long axis in order to obtain dentin slices to be bonded with one of the following adhesives: Syntac/Heliobond (Ivoclar-Vivadent) or Adper-Scotchbond-1XT (3M-ESPE). The adhesives were cured by using a LED-unit (Bluephase®, Ivoclar Vivadent) with three different curing times (10 s, 20 s and 30 s) under two ceramics (IPS-e.max-Press, Ivoclar-Vivadent; IPS-Empress®CAD, Ivoclar-Vivadent) of different thicknesses (0 mm, 0.75 mm, 2 mm). Thirty groups were included, each containing 60 measurements. Micromechanical properties (Hardness, HV; indentation modulus, E; and creep, Cr) of the adhesives were measured with an automatic microhardness indenter (Fisherscope H100C, Germany). Data were statistically analyzed by using one-way ANOVA and Tukey's post-hoc test, as well as a multivariate analysis to test the influence of the study parameters (SPSS 18.0). Significant differences were observed between the micromechanical properties of the adhesives (p ceramic type showed the highest effect on HV (Partial-eta squared (η(2)) = 0.109) of the tested adhesives, while E (η(2) = 0.275) and Cr (η(2) = 0.194) were stronger influenced by the adhesive type. Ceramic thickness showed no effect on the E and Cr of the adhesives. The adhesive bonding agents used in this study performed well by curing through different thicknesses of ceramics. The micromechanical properties of the adhesives were determined by the adhesive type and were less influenced by ceramic type and curing time.

3D multiscale micromechanical model of wood: From annual rings to microfibrils

DEFF Research Database (Denmark)

Qing, Hai; Mishnaevsky, Leon

2010-01-01

A 3D micromechanical analytical-computational model of softwood, which takes into account the wood microstructures at four scale levels, from microfibrils to annual rings, is developed. For the analysis of the effect of the annual rings structure on the properties of softwood, an improved rule-of...

Designing H-shaped micromechanical filters

International Nuclear Information System (INIS)

Arhaug, O P; Soeraasen, O

2006-01-01

This paper investigates the design constraints and possibilities given when designing a micromechanical band pass filter for intermediate frequencies (e.g. 10 MHz). The class of filters are based on coupled clamped-clamped beams constituting an H-shaped structure. A primary beam can electrostatically be activated in one of its different harmonic modes, setting the filter center frequency. The motion is transferred to an accompanying beam of equal dimensions by a mechanical coupling beam. The placement or coupling points of the quarterwavelength coupling beam which connects the vertically resonating beams is critical with respect to the bandwidth of the filters. Of special concern has been to investigate realistic dimensions allowing the filters to be processed by an actual foundry process and to find out how the choice of materials and actual dimensions would affect the performance

Micromechanics and constitutive modeling of connective soft tissues.

Science.gov (United States)

Fallah, A; Ahmadian, M T; Firozbakhsh, K; Aghdam, M M

2016-07-01

In this paper, a micromechanical model for connective soft tissues based on the available histological evidences is developed. The proposed model constituents i.e. collagen fibers and ground matrix are considered as hyperelastic materials. The matrix material is assumed to be isotropic Neo-Hookean while the collagen fibers are considered to be transversely isotropic hyperelastic. In order to take into account the effects of tissue structure in lower scales on the macroscopic behavior of tissue, a strain energy density function (SEDF) is developed for collagen fibers based on tissue hierarchical structure. Macroscopic response and properties of tissue are obtained using the numerical homogenization method with the help of ABAQUS software. The periodic boundary conditions and the proposed constitutive models are implemented into ABAQUS using the DISP and the UMAT subroutines, respectively. The existence of the solution and stable material behavior of proposed constitutive model for collagen fibers are investigated based on the poly-convexity condition. Results of the presented micromechanics model for connective tissues are compared and validated with available experimental data. Effects of geometrical and material parameters variation at microscale on macroscopic mechanical behavior of tissues are investigated. The results show that decrease in collagen content of the connective tissues like the tendon due to diseases leads 20% more stretch than healthy tissue under the same load which can results in connective tissue malfunction and hypermobility in joints. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fatigue crack tip damaging micromechanisms in a ferritic-pearlitic ductile cast iron

Directory of Open Access Journals (Sweden)

Francesco Iacoviello

2015-07-01

Full Text Available Due to the peculiar graphite elements shape, obtained by means of a chemical composition control (mainly small addition of elements like Mg, Ca or Ce, Ductile Cast Irons (DCIs are able to offer the good castability of gray irons with the high mechanical properties of irons (first of all, toughness. This interesting properties combination can be improved both by means of the chemical composition control and by means of different heat treatments(e.g. annealing, normalizing, quenching, austempering etc. In this work, fatigue crack tip damaging micromechanisms in a ferritic-pearlitic DCI were investigated by means of scanning electron microscope observations performed on a lateral surface of Compact Type (CT specimens during the fatigue crack propagation test (step by step procedure, performed according to the “load shedding procedure”. On the basis of the experimental results, different fatigue damaging micromechanisms were identified, both in the graphite nodules and in the ferritic – pearlitic matrix.

A Compilation of MATLAB Scripts and Functions for MACGMC Analyses

Science.gov (United States)

Murthy, Pappu L. N.; Bednarcyk, Brett A.; Mital, Subodh K.

2017-01-01

The primary aim of the current effort is to provide scripts that automate many of the repetitive pre- and post-processing tasks associated with composite materials analyses using the Micromechanics Analysis Code with the Generalized Method of Cells. This document consists of a compilation of hundreds of scripts that were developed in MATLAB (The Mathworks, Inc., Natick, MA) programming language and consolidated into 16 MATLAB functions. (MACGMC). MACGMC is a composite material and laminate analysis software code developed at NASA Glenn Research Center. The software package has been built around the generalized method of cells (GMC) family of micromechanics theories. The computer code is developed with a user-friendly framework, along with a library of local inelastic, damage, and failure models. Further, application of simulated thermo-mechanical loading, generation of output results, and selection of architectures to represent the composite material have been automated to increase the user friendliness, as well as to make it more robust in terms of input preparation and code execution. Finally, classical lamination theory has been implemented within the software, wherein GMC is used to model the composite material response of each ply. Thus, the full range of GMC composite material capabilities is available for analysis of arbitrary laminate configurations as well. The pre-processing tasks include generation of a multitude of different repeating unit cells (RUCs) for CMCs and PMCs, visualization of RUCs from MACGMC input and output files and generation of the RUC section of a MACGMC input file. The post-processing tasks include visualization of the predicted composite response, such as local stress and strain contours, damage initiation and progression, stress-strain behavior, and fatigue response. In addition to the above, several miscellaneous scripts have been developed that can be used to perform repeated Monte-Carlo simulations to enable probabilistic

Experiment feedbacks in micromechanics modeling of thermomechanical behaviour of SMA polycrystals

Czech Academy of Sciences Publication Activity Database

Šittner, Petr; Novák, Václav

2004-01-01

Roč. 51, - (2004), s. 321-326 ISSN 1359-6462 R&D Projects: GA AV ČR IAA1048107; GA ČR GA202/04/2016 Institutional research plan: CEZ:AV0Z1010914 Keywords : shape memory alloys (SMA) * martensitic phase transformation * micromechanical modeling * neutron diffraction Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.112, year: 2004

Micromechanical characteristics of an Al/sub 2/O/sub 3/-TiNi ceramic produced in a high-pressure chamber

Energy Technology Data Exchange (ETDEWEB)

Barashkov, G.A.; Neshpor, V.S.; Berdikov, V.F.; Pushkarev, O.I.; Lavrenova, E. A.

1987-03-01

The micromechanical characteristics of an Al/sub 2/O/sub 3/-TiNi ceramic produced in high-pressure chambers under conditions of forced mass transfer are investigated experimentally using the microindentation method. The objective of the study is to use micromechanical characteristics to determine the time required for producing an Al/sub 2/O/sub 3/-TiNi ceramic with a fully formed structure. It is found that the process of forced mass transfer and crystallization is completed within 60-120 s.

Radiation effects and micromechanics of SiC/SiC composites

International Nuclear Information System (INIS)

Ghoniem, N.M.

1992-01-01

The basic displacement damage process in SiC has been fully explored, and the mechanisms identified. Major modifications have been made to the theory of damage dosimetry in Fusion, Fission and Ion Simulation studies of Sic. For the first time, calculations of displacements per atoms in SiC can be made in any irradiation environment. Applications to irradiations in fusion first wall neutron spectra (ARIES and PROMETHEUS) as well as in fission spectra (HIFIR and FFTF) are given. Nucleation of helium-filled cavities in SiC was studied, using concepts of stability theory to determine the size of the critical nucleus under continuous generation of helium and displacement damage. It is predicted that a bimodal distribution of cavity sizes is likely to occur in heavily irradiated SiC. A study of the chemical compatibility of SiC composite structures with fusion reactor coolants at high-temperatures was undertaken. It was shown that SiC itself is chemically very stable in helium coolants in the temperature range 500--1000 degree C. However, current fiber/matrix interfaces, such as C and BN are not. The fracture mechanics of high-temperature matrix cracks with bridging fibers is now in progress. A fundamentally unique approach to study the propagation and interaction of cracks in a composite was initiated. The main focus of our research during the following period will be : (1) Theory and experiments for the micro-mechanics of high-temperature failure; and (2) Analysis of radiation damage and microstructure evolution

Fully coupled heat conduction and deformation analyses of nonlinear viscoelastic composites

KAUST Repository

Khan, Kamran; Muliana, Anastasia Hanifah

2012-01-01

This study presents an integrated micromechanical model-finite element framework for analyzing coupled heat conduction and deformations of particle-reinforced composite structures. A simplified micromechanical model consisting of four sub-cells, i

Multiscale modeling of ductile failure in metallic alloys

Science.gov (United States)

Pardoen, Thomas; Scheyvaerts, Florence; Simar, Aude; Tekoğlu, Cihan; Onck, Patrick R.

2010-04-01

Micromechanical models for ductile failure have been developed in the 1970s and 1980s essentially to address cracking in structural applications and complement the fracture mechanics approach. Later, this approach has become attractive for physical metallurgists interested by the prediction of failure during forming operations and as a guide for the design of more ductile and/or high-toughness microstructures. Nowadays, a realistic treatment of damage evolution in complex metallic microstructures is becoming feasible when sufficiently sophisticated constitutive laws are used within the context of a multilevel modelling strategy. The current understanding and the state of the art models for the nucleation, growth and coalescence of voids are reviewed with a focus on the underlying physics. Considerations are made about the introduction of the different length scales associated with the microstructure and damage process. Two applications of the methodology are then described to illustrate the potential of the current models. The first application concerns the competition between intergranular and transgranular ductile fracture in aluminum alloys involving soft precipitate free zones along the grain boundaries. The second application concerns the modeling of ductile failure in friction stir welded joints, a problem which also involves soft and hard zones, albeit at a larger scale.

Fiber Temperature Sensor Based on Micro-mechanical Membranes and Optical Interference Structure

International Nuclear Information System (INIS)

Liu Yueming; Tian Weijian; Hua Jing

2011-01-01

A novel fiber temperature sensor is presented theoretically and experimentally in this paper. Its working principle is based on Optical Fabry-Perot interference structure that is formed between a polished optical fiber end and micro-mechanical Bi-layered membranes. When ambient temperature is varying, Bi-layered membranes will be deflected and the length of Fabry-Perot cavity will be changed correspondingly. By detecting the reflecting optical intensity from the Fabry-Perot cavity, the ambient temperature can be measured. Using finite element software ANSYS, the sensor structure was optimized based on optical Interference theory and Bi-layered membranes thermal expansion theory, and theoretical characteristics was simulated by computer software. In the end, using optical fiber 2x2 coupler and photo-electrical detector, the fabricated sample sensor was tested successfully by experiment that demonstrating above theoretical analysis and simulation results. This sensor has some favorable features, such as: micro size owing to its micro-mechanical structure, high sensitivity owing to its working Fabry-Perot interference cavity structure, and optical integration character by using optical fiber techniques.

Analysis of Fiber Clustering in Composite Materials Using High-Fidelity Multiscale Micromechanics

Science.gov (United States)

Bednarcyk, Brett A.; Aboudi, Jacob; Arnold, Steven M.

2015-01-01

A new multiscale micromechanical approach is developed for the prediction of the behavior of fiber reinforced composites in presence of fiber clustering. The developed method is based on a coupled two-scale implementation of the High-Fidelity Generalized Method of Cells theory, wherein both the local and global scales are represented using this micromechanical method. Concentration tensors and effective constitutive equations are established on both scales and linked to establish the required coupling, thus providing the local fields throughout the composite as well as the global properties and effective nonlinear response. Two nondimensional parameters, in conjunction with actual composite micrographs, are used to characterize the clustering of fibers in the composite. Based on the predicted local fields, initial yield and damage envelopes are generated for various clustering parameters for a polymer matrix composite with both carbon and glass fibers. Nonlinear epoxy matrix behavior is also considered, with results in the form of effective nonlinear response curves, with varying fiber clustering and for two sets of nonlinear matrix parameters.

Collections and Analyses of Common Cause Failure Data for the Korea Standard and Westinghouse Type NPPs

International Nuclear Information System (INIS)

Kang, Dae Il; Han, S. H.

2007-04-01

The analyses of the CCF events for domestic NPPs were performed to establish the domestic database for the CCF events and to deliver supply them to the operation office of the international common cause failure data exchange (ICDE) project. We collected and analyzed the CCF events of emergency diesel generators, centrifugal pumps, motor-operated valves, check valves, circuit breakers for the Korean Standard Type nuclear power plants (NPPs), Yonggwang Units 3 and 4 and Ulchin Units 3 and 4, and the Westinghouse type NPPs, Kori Unit 3 and 4 and Yonggwang Units 1 and 2. First, the components to be collected and analyzed were classified into the common cause component groups (CCCGs) according to the ICDE coding guidelines. Next, the CCF events were identified based on reviews of the component database for the PSA and its related documents, and consultations with NPP staff. Fourteen CCF events were identified. The ratio of the number of CCF events to that of individual failure events was identified as approximately 10 percentages. However, an in depth review of the CCF events showed that most failure severities of them were identified as partial CCF events, which can be interpreted as some component failures within the CCCGs. Root causes of the CCF events were identified as 9 internal part failures, 2 human errors, 2 design deficiencies, 1 procedure inadequacy. It could be concluded that the major root causes of the CCF events were internal piece part failures

Investigation of Macroscopic Brittle Creep Failure Caused by Microcrack Growth Under Step Loading and Unloading in Rocks

Science.gov (United States)

Li, Xiaozhao; Shao, Zhushan

2016-07-01

The growth of subcritical cracks plays an important role in the creep of brittle rock. The stress path has a great influence on creep properties. A micromechanics-based model is presented to study the effect of the stress path on creep properties. The microcrack model of Ashby and Sammis, Charles' Law, and a new micro-macro relation are employed in our model. This new micro-macro relation is proposed by using the correlation between the micromechanical and macroscopic definition of damage. A stress path function is also introduced by the relationship between stress and time. Theoretical expressions of the stress-strain relationship and creep behavior are derived. The effects of confining pressure on the stress-strain relationship are studied. Crack initiation stress and peak stress are achieved under different confining pressures. The applied constant stress that could cause creep behavior is predicted. Creep properties are studied under the step loading of axial stress or the unloading of confining pressure. Rationality of the micromechanics-based model is verified by the experimental results of Jinping marble. Furthermore, the effects of model parameters and the unloading rate of confining pressure on creep behavior are analyzed. The coupling effect of step axial stress and confining pressure on creep failure is also discussed. The results provide implications on the deformation behavior and time-delayed rockburst mechanism caused by microcrack growth on surrounding rocks during deep underground excavations.

Multi-scale modeling of ductile failure in metallic alloys

International Nuclear Information System (INIS)

Pardoen, Th.; Scheyvaerts, F.; Simar, A.; Tekoglu, C.; Onck, P.R.

2010-01-01

Micro-mechanical models for ductile failure have been developed in the seventies and eighties essentially to address cracking in structural applications and complement the fracture mechanics approach. Later, this approach has become attractive for physical metallurgists interested by the prediction of failure during forming operations and as a guide for the design of more ductile and/or high-toughness microstructures. Nowadays, a realistic treatment of damage evolution in complex metallic microstructures is becoming feasible when sufficiently sophisticated constitutive laws are used within the context of a multilevel modelling strategy. The current understanding and the state of the art models for the nucleation, growth and coalescence of voids are reviewed with a focus on the underlying physics. Considerations are made about the introduction of the different length scales associated with the microstructure and damage process. Two applications of the methodology are then described to illustrate the potential of the current models. The first application concerns the competition between intergranular and transgranular ductile fracture in aluminum alloys involving soft precipitate free zones along the grain boundaries. The second application concerns the modeling of ductile failure in friction stir welded joints, a problem which also involves soft and hard zones, albeit at a larger scale. (authors)

Micromechanical modeling of stress-induced strain in polycrystalline Ni–Mn–Ga by directional solidification

International Nuclear Information System (INIS)

Zhu, Yuping; Shi, Tao; Teng, Yao

2015-01-01

Highlights: • A micromechanical model of directional solidification Ni–Mn–Ga is developed. • The stress–strain curves in different directions are tested. • The martensite Young’s moduli in different directions are predicted. • The macro reorientation strains in different directions are investigated. - Abstract: Polycrystalline ferromagnetic shape memory alloy Ni–Mn–Ga produced by directional solidification possess unique properties. Its compressive stress–strain behaviors in loading–unloading cycle show nonlinear and anisotropic. Based on the self-consistent theory and thermodynamics principle, a micromechanical constitutive model of polycrystalline Ni–Mn–Ga by directional solidification is developed considering the generating mechanism of the macroscopic strain and anisotropy. Then, the stress induced strains at different angles to solidification direction are calculated, and the results agree well with the experimental data. The predictive curves of martensite Young’s modulus and macro reorientation strain in different directions are investigated. It may provide theoretical guidance for the design and use of ferromagnetic shape memory alloy

Micromechanical Behavior of Single-Crystal Superalloy with Different Crystal Orientations by Microindentation

Directory of Open Access Journals (Sweden)

Jinghui Li

2015-01-01

Full Text Available In order to investigate the anisotropic micromechanical properties of single-crystal nickel-based superalloy DD99 of four crystallographic orientations, (001, (215, (405, and (605, microindentation test (MIT was conducted with different loads and loading velocities by a sharp Berkovich indenter. Some material parameters reflecting the micromechanical behavior of DD99, such as microhardness H, Young’s modulus E, yield stress σy, strain hardening component n, and tensile strength σb, can be obtained from load-displacement relations. H and E of four different crystal planes evidently decrease with the increase of h. The reduction of H is due to dislocation hardening while E is related to interplanar spacing and crystal variable. σy of (215 is the largest among four crystal planes, followed by (605, and (001 has the lowest value. n of (215 is the lowest, followed by (605, and that of (001 is the largest. Subsequently, a simplified elastic-plastic material model was employed for 3D microindentation simulation of DD99 with various crystal orientations. The simulation results agreed well with experimental, which confirmed the accuracy of the simplified material model.

Materials selection in micromechanical design: an application of the Ashby approach

OpenAIRE

Srikar, V.T.; Spearing, S.M.

2003-01-01

The set of materials available to microsystems designers is rapidly expanding. Techniques now exist to introduce and integrate a large number of metals, alloys, ceramics, glasses, polymers, and elastomers into microsystems, motivating the need for a rational approach for materials selection in microsystems design. As a step toward such an approach, we focus on the initial stages of materials selection for micromechanical structures with minimum feature sizes greater than 1 /spl mu/m. The vari...

Blu-Ray-based micromechanical characterization platform for biopolymer degradation assessment

DEFF Research Database (Denmark)

Casci Ceccacci, Andrea; Chen, Ching-Hsiu; Hwu, En-Te

2017-01-01

Degradable biopolymers are used as carrier materials in drug delivery devices. A complete understanding of their degradation behaviour is thus crucial in the design of new delivery systems. Here we combine a reliable method, based on spray coated micromechanical resonators and a disposable...... microfluidic chip, to characterize biopolymer degradation under the action of enzymes in controlled flow condition. The sensing platform is based on the mechanics and optics from a Blu-Ray player, which automatically localize individual sensors within the array, and sequentially measure and record...

BILAM: a composite laminate failure-analysis code using bilinear stress-strain approximations

Energy Technology Data Exchange (ETDEWEB)

McLaughlin, P.V. Jr.; Dasgupta, A.; Chun, Y.W.

1980-10-01

The BILAM code which uses constant strain laminate analysis to generate in-plane load/deformation or stress/strain history of composite laminates to the point of laminate failure is described. The program uses bilinear stress-strain curves to model layer stress-strain behavior. Composite laminates are used for flywheels. The use of this computer code will help to develop data on the behavior of fiber composite materials which can be used by flywheel designers. In this program the stress-strain curves are modelled by assuming linear response in axial tension while using bilinear approximations (2 linear segments) for stress-strain response to axial compressive, transverse tensile, transverse compressive and axial shear loadings. It should be noted that the program attempts to empirically simulate the effects of the phenomena which cause nonlinear stress-strain behavior, instead of mathematically modelling the micromechanics involved. This code, therefore, performs a bilinear laminate analysis, and, in conjunction with several user-defined failure interaction criteria, is designed to provide sequential information on all layer failures up to and including the first fiber failure. The modus operandi is described. Code BILAM can be used to: predict the load-deformation/stress-strain behavior of a composite laminate subjected to a given combination of in-plane loads, and make analytical predictions of laminate strength.

A Microstructure-Based Model to Characterize Micromechanical Parameters Controlling Compressive and Tensile Failure in Crystallized Rock

Science.gov (United States)

Kazerani, T.; Zhao, J.

2014-03-01

A discrete element model is proposed to examine rock strength and failure. The model is implemented by UDEC which is developed for this purpose. The material is represented as a collection of irregular-sized deformable particles interacting at their cohesive boundaries. The interface between two adjacent particles is viewed as a flexible contact whose stress-displacement law is assumed to control the material fracture and fragmentation process. To reproduce rock anisotropy, an innovative orthotropic cohesive law is developed for contact which allows the interfacial shear and tensile behaviours to be different from each other. The model is applied to a crystallized igneous rock and the individual and interactional effects of the microstructural parameters on the material compressive and tensile failure response are examined. A new methodical calibration process is also established. It is shown that the model successfully reproduces the rock mechanical behaviour quantitatively and qualitatively. Ultimately, the model is used to understand how and under what circumstances micro-tensile and micro-shear cracking mechanisms control the material failure at different loading paths.

Interface effects on the micromechanical response of a transversely loaded single fiber SCS-6/Ti-6Al-4V composite

International Nuclear Information System (INIS)

Warrier, S.G.; Majumdar, B.S.; Gundel, D.B.; Miracle, D.B.

1996-01-01

The ability of a fiber-matrix interface to support a transverse load is typically evaluated in straight-sided composite specimens where a stress singularity exists at the free surface of the interface. This stress singularity is often the cause of crack initiation and debonding during transverse loading. In order to develop a fundamental understanding of the transverse behavior of the fiber-matrix interface, it is necessary to alter the crack initiation site from the free surface to an internal location. To achieve this objective, a cross-shaped specimen has been recently developed. In this study, based on the experimentally observed onset of nonlinearity in the stress-strain curve of these specimens and finite element analysis, the bond strength of the SCS-6/Ti-6Al-4V interface was determined to be 115 MPa. The micromechanical behavior of these specimens under transverse loading was examined by finite element analysis using this interface bond strength value and compared with experimental observations. Results demonstrate that the proposed geometry was successful in suppressing debonding at the surface and altering it to an internal event. The results from numerical analysis correlated well with the experimental stress-strain curve and several simple analytical models. In an attempt to identify the true bond strength and the interface failure criterion, the present study suggests that if failure initiates under tensile radial stresses, then the normal bond strength of the SCS-6/Ti-6Al-4V composites is about 115 MPa; under shear failure, the tangential shear strength of the interface is about 180 MPa

Linear micromechanical stepping drive for pinhole array positioning

International Nuclear Information System (INIS)

Endrödy, Csaba; Mehner, Hannes; Hoffmann, Martin; Grewe, Adrian

2015-01-01

A compact linear micromechanical stepping drive for positioning a 7 × 5.5 mm 2 optical pinhole array is presented. The system features a step size of 13.2 µm and a full displacement range of 200 µm. The electrostatic inch-worm stepping mechanism shows a compact design capable of positioning a payload 50% of its own weight. The stepping drive movement, step sizes and position accuracy are characterized. The actuated pinhole array is integrated in a confocal chromatic hyperspectral imaging system, where coverage of the object plane, and therefore the useful picture data, can be multiplied by 14 in contrast to a non-actuated array. (paper)

Detection of electromagnetic radiation using micromechanical multiple quantum wells structures

Science.gov (United States)

Datskos, Panagiotis G [Knoxville, TN; Rajic, Slobodan [Knoxville, TN; Datskou, Irene [Knoxville, TN

2007-07-17

An apparatus and method for detecting electromagnetic radiation employs a deflectable micromechanical apparatus incorporating multiple quantum wells structures. When photons strike the quantum-well structure, physical stresses are created within the sensor, similar to a "bimetallic effect." The stresses cause the sensor to bend. The extent of deflection of the sensor can be measured through any of a variety of conventional means to provide a measurement of the photons striking the sensor. A large number of such sensors can be arranged in a two-dimensional array to provide imaging capability.

Role of discrete intragranular slip on lattice rotations in polycrystalline Ni: Experimental and micromechanical studies

International Nuclear Information System (INIS)

Perrin, C.; Berbenni, S.; Vehoff, H.; Berveiller, M.

2010-01-01

In this paper, a new micromechanical approach accounting for the discreteness of intragranular slip is used to derive the local misorientations in the case of plastically deformed polycrystalline nickel in uniaxial tension. This intragranular microstructure is characterized in particular single slip grains by atomic force microscopy measurements in the early stage of plastic deformation. The micromechanical modelling accounts for the individual grain size, the spatial distances between active slip bands and the magnitude of slip in bands. The slip bands are modelled using discrete distributions of circular super glide dislocation loops constrained at grain boundaries for a spherical grain boundary embedded in an infinite matrix. In contrast with classic mean field approaches based on Eshelby's plastic inclusion concept, the present model is able to capture different intragranular behaviours between near grain boundary regions and grain interiors. These theoretical results are quantitatively confirmed by local electron backscatter diffraction measurements regarding intragranular misorientation mapping with respect to a reference point in the centre of the grain.

KOH concentration effect on the cycle life of nickel-hydrogen cells. 4: Results of failure analyse

Science.gov (United States)

Lim, H. S.; Verzwyvelt, S. A.

1989-01-01

Effects of KOH concentrations on failure modes and mechanisms of nickel-hydrogen cells were studied using long cycled boiler plate cells containing electrolytes of various KOH concentrations ranging 21 to 36 percent. Life of these cells were up to 40,000 cycles in an accelerated low earth orbit (LEO) cycle regime at 80 percent depth of discharge. An interim life test results were reported earlier in J. Power Sources, 22, 213-220, 1988. The results of final life test, end-of-life cell performance, and teardown analyses are discussed. These teardown analyses included visual observations, measurements of nickel electrode capacity in an electrolyte-flooded cell, dimensional changes of cell components, SEM studies on cell cross section, BET surface area and pore volume distribution in cycled nickel electrodes, and chemical analyses. Cycle life of a nickel-hydrogen cell was improved tremendously as KOH concentration was decreased from 36 to 31 percent and from 31 to 26 percent while effect of further concentration decrease was complicated as described in our earlier report. Failure mode of high concentration (31 to 36 percent) cells was gradual capacity decrease, while that of low concentration (21 to 26 percent) cells was mainly formation of a soft short. Long cycled (25,000 to 40,000 cycles) nickel electrodes were expanded more than 50 percent of the initial value, but no correlation was found between this expansion and measured capacity. All electrodes cycled in low concentration (21 to 26 percent) cells had higher capacity than those cycled in high concentration (31 to 36 percent) cells.

Micromechanics and statistics of slipping events in a granular seismic fault model

Energy Technology Data Exchange (ETDEWEB)

Arcangelis, L de [Department of Information Engineering and CNISM, Second University of Naples, Aversa (Italy); Ciamarra, M Pica [CNR-SPIN, Dipartimento di Scienze Fisiche, Universita di Napoli Federico II (Italy); Lippiello, E; Godano, C, E-mail: dearcangelis@na.infn.it [Department of Environmental Sciences and CNISM, Second University of Naples, Caserta (Italy)

2011-09-15

The stick-slip is investigated in a seismic fault model made of a confined granular system under shear stress via three dimensional Molecular Dynamics simulations. We study the statistics of slipping events and, in particular, the dependence of the distribution on model parameters. The distribution consistently exhibits two regimes: an initial power law and a bump at large slips. The initial power law decay is in agreement with the the Gutenberg-Richter law characterizing real seismic occurrence. The exponent of the initial regime is quite independent of model parameters and its value is in agreement with experimental results. Conversely, the position of the bump is solely controlled by the ratio of the drive elastic constant and the system size. Large slips also become less probable in absence of fault gouge and tend to disappear for stiff drives. A two-time force-force correlation function, and a susceptibility related to the system response to pressure changes, characterize the micromechanics of slipping events. The correlation function unveils the micromechanical changes occurring both during microslips and slips. The mechanical susceptibility encodes the magnitude of the incoming microslip. Numerical results for the cellular-automaton version of the spring block model confirm the parameter dependence observed for size distribution in the granular model.

Mechanical design and force calibration of dual-axis micromechanical probe for friction force microscopy

International Nuclear Information System (INIS)

Fukuzawa, Kenji; Terada, Satoshi; Shikida, Mitsuhiro; Amakawa, Hiroaki; Zhang, Hedong; Mitsuya, Yasunaga

2007-01-01

A dual-axis micromechanical probe that combines a double cantilever and torsion beams is presented. This probe can reduce the mechanical cross-talk between the lateral and vertical force detections. In addition, dual-axis forces can be detected by measuring the dual-axis displacement of the probe end using the optical lever-based method used in conventional friction force microscopes (FFMs). In this paper, the mechanical design of the probe, the details of the fabrication method, FFM performance, and calibration of the friction force are discussed. The mechanical design and the microfabrication method for probes that can provide a force resolution of the order of 1 nN without mechanical cross-talk are presented. Calibration of the lateral force signal is possible by using the relationship between the lateral force and the piezodisplacement at the onset of the probe scanning. The micromechanical probe enables simultaneous and independent detection of atomic and friction forces. This leads to accurate investigation of nanotribological phenomena and visualization of the distribution of the friction properties, which helps the identification of the material properties

Micro-mechanics based damage mechanics for 3D Orthogonal Woven Composites: Experiment and Numerical Modelling

KAUST Repository

Saleh, Mohamed Nasr; Lubineau, Gilles; Potluri, Prasad; Withers, Philip; Soutis, Constantinos

2016-01-01

Damage initiation and evolution of three-dimensional (3D) orthogonal woven carbon fibre composite (3DOWC) is investigated experimentally and numerically. Meso-scale homogenisation of the representative volume element (RVE) is utilised to predict the elastic properties, simulate damage initiation and evolution when loaded in tension. The effect of intra-yarns transverse cracking and shear diffused damage on the in-plane transverse modulus and shear modulus is investigated while one failure criterion is introduced to simulate the matrix damage. The proposed model is based on two major assumptions. First, the effect of the binder yarns, on the in-plane properties, is neglected, so the 3DOWC unit cell can be approximated as a (0o/90o) cross-ply laminate. Second, a micro-mechanics based damage approach is used at the meso-scale, so damage indicators can be correlated, explicitly, to the density of cracks within the material. Results from the simulated RVE are validated against experimental results along the warp (0o direction) and weft (90o direction). This approach paves the road for more predictive models as damage evolution laws are obtained from micro mechanical considerations and rely on few well-defined material parameters. This largely differs from classical damage mechanics approaches in which the evolution law is obtained by retrofitting experimental observations.

Micro-mechanics based damage mechanics for 3D Orthogonal Woven Composites: Experiment and Numerical Modelling

KAUST Repository

Saleh, Mohamed Nasr

2016-01-08

Damage initiation and evolution of three-dimensional (3D) orthogonal woven carbon fibre composite (3DOWC) is investigated experimentally and numerically. Meso-scale homogenisation of the representative volume element (RVE) is utilised to predict the elastic properties, simulate damage initiation and evolution when loaded in tension. The effect of intra-yarns transverse cracking and shear diffused damage on the in-plane transverse modulus and shear modulus is investigated while one failure criterion is introduced to simulate the matrix damage. The proposed model is based on two major assumptions. First, the effect of the binder yarns, on the in-plane properties, is neglected, so the 3DOWC unit cell can be approximated as a (0o/90o) cross-ply laminate. Second, a micro-mechanics based damage approach is used at the meso-scale, so damage indicators can be correlated, explicitly, to the density of cracks within the material. Results from the simulated RVE are validated against experimental results along the warp (0o direction) and weft (90o direction). This approach paves the road for more predictive models as damage evolution laws are obtained from micro mechanical considerations and rely on few well-defined material parameters. This largely differs from classical damage mechanics approaches in which the evolution law is obtained by retrofitting experimental observations.

Parametric and Wavelet Analyses of Acoustic Emission Signals for the Identification of Failure Modes in CFRP Composites Using PZT and PVDF Sensors

Energy Technology Data Exchange (ETDEWEB)

Prasopchaichana, Kritsada; Kwon, Oh Yang [Inha University, Incheon (Korea, Republic of)

2007-12-15

Combination of the parametric and the wavelet analyses of acoustic emission (AE) signals was applied to identify the failure modes in carbon fiber reinforced plastic (CFRP) composite laminates during tensile testing. AE signals detected by surface mounted lead-zirconate-titanate (PZT) and polyvinylidene fluoride (PVDF) sensors were analyzed by parametric analysis based on the time of occurrence which classifies AE signals corresponding to failure modes. The frequency band level-energy analysis can distinguish the dominant frequency band for each failure mode. It was observed that the same type of failure mechanism produced signals with different characteristics depending on the stacking sequences and the type of sensors. This indicates that the proposed method can identify the failure modes of the signals if the stacking sequences and the sensors used are known

Micromechanics based framework with second-order damage tensors

Science.gov (United States)

Desmorat, R.; Desmorat, B.; Olive, M.; Kolev, B.

2018-05-01

The harmonic product of tensors---leading to the concept of harmonic factorization---has been defined in a previous work (Olive et al, 2017). In the practical case of 3D crack density measurements on thin or thick walled structures, this mathematical tool allows us to factorize the harmonic (irreducible) part of the fourth-order damage tensor as an harmonic square: an exact harmonic square in 2D, an harmonic square over the set of so-called mechanically accessible directions for measurements in the 3D case. The corresponding micro-mechanics framework based on second---instead of fourth---order damage tensors is derived. An illustrating example is provided showing how the proposed framework allows for the modeling of the so-called hydrostatic sensitivity up to high damage levels.

MEMS resonant load cells for micro-mechanical test frames: feasibility study and optimal design

Science.gov (United States)

Torrents, A.; Azgin, K.; Godfrey, S. W.; Topalli, E. S.; Akin, T.; Valdevit, L.

2010-12-01

This paper presents the design, optimization and manufacturing of a novel micro-fabricated load cell based on a double-ended tuning fork. The device geometry and operating voltages are optimized for maximum force resolution and range, subject to a number of manufacturing and electromechanical constraints. All optimizations are enabled by analytical modeling (verified by selected finite elements analyses) coupled with an efficient C++ code based on the particle swarm optimization algorithm. This assessment indicates that force resolutions of ~0.5-10 nN are feasible in vacuum (~1-50 mTorr), with force ranges as large as 1 N. Importantly, the optimal design for vacuum operation is independent of the desired range, ensuring versatility. Experimental verifications on a sub-optimal device fabricated using silicon-on-glass technology demonstrate a resolution of ~23 nN at a vacuum level of ~50 mTorr. The device demonstrated in this article will be integrated in a hybrid micro-mechanical test frame for unprecedented combinations of force resolution and range, displacement resolution and range, optical (or SEM) access to the sample, versatility and cost.

Micromechanical Characterization of Complex Polypropylene Morphologies by HarmoniX AFM

Directory of Open Access Journals (Sweden)

S. Liparoti

2017-01-01

Full Text Available This paper examines the capability of the HarmoniX Atomic Force Microscopy (AFM technique to draw accurate and reliable micromechanical characterization of complex polymer morphologies generally found in conventional thermoplastic polymers. To that purpose, injection molded polypropylene samples, containing representative morphologies, have been characterized by HarmoniX AFM. Mapping and distributions of mechanical properties of the samples surface are determined and analyzed. Effects of sample preparation and test conditions are also analyzed. Finally, the AFM determination of surface elastic moduli has been compared with that obtained by indentation tests, finding good agreement among the results.

Micromechanical anisotropy and heterogeneity of the meniscus extracellular matrix.

Science.gov (United States)

Li, Qing; Qu, Feini; Han, Biao; Wang, Chao; Li, Hao; Mauck, Robert L; Han, Lin

2017-05-01

To understand how the complex biomechanical functions of the meniscus are endowed by the nanostructure of its extracellular matrix (ECM), we studied the anisotropy and heterogeneity in the micromechanical properties of the meniscus ECM. We used atomic force microscopy (AFM) to quantify the time-dependent mechanical properties of juvenile bovine meniscus at deformation length scales corresponding to the diameters of collagen fibrils. At this scale, anisotropy in the elastic modulus of the circumferential fibers, the major ECM structural unit, can be attributed to differences in fibril deformation modes: uncrimping when normal to the fiber axis, and laterally constrained compression when parallel to the fiber axis. Heterogeneity among different structural units is mainly associated with their variations in microscale fiber orientation, while heterogeneity across anatomical zones is due to alterations in collagen fibril diameter and alignment at the nanoscale. Unlike the elastic modulus, the time-dependent properties are more homogeneous and isotropic throughout the ECM. These results enable a detailed understanding of the meniscus structure-mechanics at the nanoscale, and can serve as a benchmark for understanding meniscus biomechanical functions, documenting disease progression and designing tissue repair strategies. Meniscal damage is a common cause of joint injury, which can lead to the development of post-traumatic osteoarthritis among young adults. Restoration of meniscus function requires repairing its highly heterogeneous and complex extracellular matrix. Employing AFM, this study quantifies the anisotropic and heterogeneous features of the meniscus ECM structure and mechanics. The micromechanical properties are interpreted within the context of the collagen fibril nanostructure and its variation with tissue anatomical locations. These results provide a fundamental structure-mechanics knowledge benchmark, against which, repair and regeneration strategies can

Micromechanical modelling of quasi-brittle materials behavior

International Nuclear Information System (INIS)

Li, V.C.

1992-01-01

This special issues on Micromechanical modelling of quasi-brittle materials behavior represents an outgrowth of presentations given at a symposium of the same title held at the 1991 ASME Applied Mechanics and Biomechanics Summer Conference at the Ohio State University. The symposium was organized to promote communication between researchers in three materials groups: rock, cementitious materials, ceramics and related composites. The enthusiastic response of both speakers and attendants at the ASME symposium convinced the organizer that it would be useful to put together a coherent volume which can reach a larger audience. It was decided that the papers individually and as a volume ought to provide a broader view, so that as much as possible, the work contained in each paper would be accessible to readers working in any of the three materials groups. Applied Mechanics Reviews presents an appropriate platform for achieving these objectives

A micromechanical device that monitors arterial pressure during general anesthesia and in intensive care units

Science.gov (United States)

Andreeva, A. V.; Luchinin, V. V.; Kuzmina, K. A.; Klyavinek, A. S.; Karelov, A. E.

2015-12-01

A vibroacoustic fiber optic system that consists of micromechanical components designated for use in medicine and biology is reviewed. A theoretical analysis of a fiber optic microphone is done and its optimal construction parameters are determined. The possibility of using the developed system with magnetic resonance tomography to noninvasively measure man's arterial pressure is specified.

Single coil bistable, bidirectional micromechanical actuator

Science.gov (United States)

Tabat, Ned; Guckel, Henry

1998-09-15

Micromechanical actuators capable of bidirectional and bistable operation can be formed on substrates using lithographic processing techniques. Bistable operation of the microactuator is obtained using a single coil and a magnetic core with a gap. A plunger having two magnetic heads is supported for back and forth linear movement with respect to the gap in the magnetic core, and is spring biased to a neutral position in which the two heads are on each side of the gap in the core. The single electrical coil is coupled to the core and is provided with electrical current to attract one of the heads toward the core by reluctance action to drive the plunger to a limit of travel in one direction. The current is then cut off and the plunger returns by spring action toward the gap, whereafter the current is reapplied to the coil to attract the other head of the plunger by reluctance action to drive the plunger to its other limit of travel. This process can be repeated at a time when switching of the actuator is required.

Computational micromechanics analysis of electron hopping and interfacial damage induced piezoresistive response in carbon nanotube-polymer nanocomposites

International Nuclear Information System (INIS)

Chaurasia, A K; Seidel, G D; Ren, X

2014-01-01

Carbon nanotube (CNT)-polymer nanocomposites have been observed to exhibit an effective macroscale piezoresistive response, i.e., change in macroscale resistivity when subjected to applied deformation. The macroscale piezoresistive response of CNT-polymer nanocomposites leads to deformation/strain sensing capabilities. It is believed that the nanoscale phenomenon of electron hopping is the major driving force behind the observed macroscale piezoresistivity of such nanocomposites. Additionally, CNT-polymer nanocomposites provide damage sensing capabilities because of local changes in electron hopping pathways at the nanoscale because of initiation/evolution of damage. The primary focus of the current work is to explore the effect of interfacial separation and damage at the nanoscale CNT-polymer interface on the effective macroscale piezoresistive response. Interfacial separation and damage are allowed to evolve at the CNT-polymer interface through coupled electromechanical cohesive zones, within a finite element based computational micromechanics framework, resulting in electron hopping based current density across the separated CNT-polymer interface. The macroscale effective material properties and gauge factors are evaluated using micromechanics techniques based on electrostatic energy equivalence. The impact of the electron hopping mechanism, nanoscale interface separation and damage evolution on the effective nanocomposite electrostatic and piezoresistive response is studied in comparison with the perfectly bonded interface. The effective electrostatic/piezoresistive response for the perfectly bonded interface is obtained based on a computational micromechanics model developed in the authors’ earlier work. It is observed that the macroscale effective gauge factors are highly sensitive to strain induced formation/disruption of electron hopping pathways, interface separation and the initiation/evolution of interfacial damage. (paper)

Micromechanical Time-Lapse X-ray CT Study of Fatigue Damage in Uni-Directional Fibre Composites

DEFF Research Database (Denmark)

Jespersen, Kristine Munk; Lowe, Tristan; Withers, Philip J.

2015-01-01

. The geometry of the cut-out is similar to that which will be used in the time-lapse study. As the micro-mechanical damage mechanisms are small features, it is necessary to obtain a high scan resolution which sets a limit to how large the field of view can be. Therefore, it is necessary to perform several scans...

Sideband cooling of micromechanical motion to the quantum ground state.

Science.gov (United States)

Teufel, J D; Donner, T; Li, Dale; Harlow, J W; Allman, M S; Cicak, K; Sirois, A J; Whittaker, J D; Lehnert, K W; Simmonds, R W

2011-07-06

The advent of laser cooling techniques revolutionized the study of many atomic-scale systems, fuelling progress towards quantum computing with trapped ions and generating new states of matter with Bose-Einstein condensates. Analogous cooling techniques can provide a general and flexible method of preparing macroscopic objects in their motional ground state. Cavity optomechanical or electromechanical systems achieve sideband cooling through the strong interaction between light and motion. However, entering the quantum regime--in which a system has less than a single quantum of motion--has been difficult because sideband cooling has not sufficiently overwhelmed the coupling of low-frequency mechanical systems to their hot environments. Here we demonstrate sideband cooling of an approximately 10-MHz micromechanical oscillator to the quantum ground state. This achievement required a large electromechanical interaction, which was obtained by embedding a micromechanical membrane into a superconducting microwave resonant circuit. To verify the cooling of the membrane motion to a phonon occupation of 0.34 ± 0.05 phonons, we perform a near-Heisenberg-limited position measurement within (5.1 ± 0.4)h/2π, where h is Planck's constant. Furthermore, our device exhibits strong coupling, allowing coherent exchange of microwave photons and mechanical phonons. Simultaneously achieving strong coupling, ground state preparation and efficient measurement sets the stage for rapid advances in the control and detection of non-classical states of motion, possibly even testing quantum theory itself in the unexplored region of larger size and mass. Because mechanical oscillators can couple to light of any frequency, they could also serve as a unique intermediary for transferring quantum information between microwave and optical domains.

Concentration independent modulation of local micromechanics in a fibrin gel.

Directory of Open Access Journals (Sweden)

Maxwell A Kotlarchyk

Full Text Available Methods for tuning extracellular matrix (ECM mechanics in 3D cell culture that rely on increasing the concentration of either protein or cross-linking molecules fail to control important parameters such as pore size, ligand density, and molecular diffusivity. Alternatively, ECM stiffness can be modulated independently from protein concentration by mechanically loading the ECM. We have developed a novel device for generating stiffness gradients in naturally derived ECMs, where stiffness is tuned by inducing strain, while local mechanical properties are directly determined by laser tweezers based active microrheology (AMR. Hydrogel substrates polymerized within 35 mm diameter Petri dishes are strained non-uniformly by the precise rotation of an embedded cylindrical post, and exhibit a position-dependent stiffness with little to no modulation of local mesh geometry. Here we present the device in the context of fibrin hydrogels. First AMR is used to directly measure local micromechanics in unstrained hydrogels of increasing fibrin concentration. Changes in stiffness are then mapped within our device, where fibrin concentration is held constant. Fluorescence confocal imaging and orbital particle tracking are used to quantify structural changes in fibrin on the micro and nano levels respectively. The micromechanical strain stiffening measured by microrheology is not accompanied by ECM microstructural changes under our applied loads, as measured by confocal microscopy. However, super-resolution orbital tracking reveals nanostructural straightening, lengthening, and reduced movement of fibrin fibers. Furthermore, we show that aortic smooth muscle cells cultured within our device are morphologically sensitive to the induced mechanical gradient. Our results demonstrate a powerful cell culture tool that can be used in the study of mechanical effects on cellular physiology in naturally derived 3D ECM tissues.

Analyses Of Techniques On Structural Fatigue Failure Detection ...

African Journals Online (AJOL)

Machines and structures are subjected to variable loading conditions where the stress cycle does not remain the same during the operation of the machine. Fatigue is undoubtedly one of the most serious of all causes of breakdowns of machines and structures which results in sudden failures. The use of the time domain ...

Micromechanisms of ductile stable crack growth in nuclear pressure vessel steels

Energy Technology Data Exchange (ETDEWEB)

Belcher, W.P.A.; Druce, S.G.

1981-10-01

The objective of this work was to investigate the relationship between the micromechanisms of ductile crack growth, the microstructural constituent phases present in nuclear pressure vessel steel, and the observed fracture behavior as determined by impact and fracture mechanics tests. Results from a microstructural and mechanical property comparison of an A508 Class 3 pressurized water reactor nozzle forging cutout and a 150-mm-thick A533B Class 1 plate are reported. The variation of upper-shelf toughness between the two steels and its orientation sensitivity are discussed on the basis of inclusion and precipitate distributions. Inclusion clusters in A533B, deformed to elongated disks in the rolling plane, have a profound effect on short transverse fracture properties. Data derived using the multi-specimen J-integral method to characterize the initiation of ductile crack extension and resistance to stable crack growth are compared with equivalent Charpy results. Results of the J /SUB R/ -curve analyses indicate (1) that the A533B short transverse crack growth resistance is approximately half that observed from transverse and longitudinal specimen orientations, and (2) that the A508 initiation toughness and resistance to stable crack growth are insensitive to position through the forging wall, and are higher than exhibited by A533B at any orientation in the midthickness position.

Failure assessments of corroded pipelines with axial defects using stress-based criteria: Numerical studies and verification analyses

International Nuclear Information System (INIS)

Chiodo, Mario S.G.; Ruggieri, Claudio

2009-01-01

Conventional procedures used to assess the integrity of corroded piping systems with axial defects generally employ simplified failure criteria based upon a plastic collapse failure mechanism incorporating the tensile properties of the pipe material. These methods establish acceptance criteria for defects based on limited experimental data for low strength structural steels which do not necessarily address specific requirements for the high grade steels currently used. For these cases, failure assessments may be overly conservative or provide significant scatter in their predictions, which lead to unnecessary repair or replacement of in-service pipelines. Motivated by these observations, this study examines the applicability of a stress-based criterion based upon plastic instability analysis to predict the failure pressure of corroded pipelines with axial defects. A central focus is to gain additional insight into effects of defect geometry and material properties on the attainment of a local limit load to support the development of stress-based burst strength criteria. The work provides an extensive body of results which lend further support to adopt failure criteria for corroded pipelines based upon ligament instability analyses. A verification study conducted on burst testing of large-diameter pipe specimens with different defect length shows the effectiveness of a stress-based criterion using local ligament instability in burst pressure predictions, even though the adopted burst criterion exhibits a potential dependence on defect geometry and possibly on material's strain hardening capacity. Overall, the results presented here suggests that use of stress-based criteria based upon plastic instability analysis of the defect ligament is a valid engineering tool for integrity assessments of pipelines with axial corroded defects

Failure assessments of corroded pipelines with axial defects using stress-based criteria: Numerical studies and verification analyses

Energy Technology Data Exchange (ETDEWEB)

Chiodo, Mario S.G. [Department of Naval Architecture and Ocean Engineering, University of Sao Paulo, Av. Prof. Mello Moraes, 2231 (PNV-EPUSP), Sao Paulo, SP 05508-030 (Brazil); Ruggieri, Claudio [Department of Naval Architecture and Ocean Engineering, University of Sao Paulo, Av. Prof. Mello Moraes, 2231 (PNV-EPUSP), Sao Paulo, SP 05508-030 (Brazil)], E-mail: claudio.ruggieri@poli.usp.br

2009-02-15

Conventional procedures used to assess the integrity of corroded piping systems with axial defects generally employ simplified failure criteria based upon a plastic collapse failure mechanism incorporating the tensile properties of the pipe material. These methods establish acceptance criteria for defects based on limited experimental data for low strength structural steels which do not necessarily address specific requirements for the high grade steels currently used. For these cases, failure assessments may be overly conservative or provide significant scatter in their predictions, which lead to unnecessary repair or replacement of in-service pipelines. Motivated by these observations, this study examines the applicability of a stress-based criterion based upon plastic instability analysis to predict the failure pressure of corroded pipelines with axial defects. A central focus is to gain additional insight into effects of defect geometry and material properties on the attainment of a local limit load to support the development of stress-based burst strength criteria. The work provides an extensive body of results which lend further support to adopt failure criteria for corroded pipelines based upon ligament instability analyses. A verification study conducted on burst testing of large-diameter pipe specimens with different defect length shows the effectiveness of a stress-based criterion using local ligament instability in burst pressure predictions, even though the adopted burst criterion exhibits a potential dependence on defect geometry and possibly on material's strain hardening capacity. Overall, the results presented here suggests that use of stress-based criteria based upon plastic instability analysis of the defect ligament is a valid engineering tool for integrity assessments of pipelines with axial corroded defects.

Temperature effect on crack resistance and fracture micromechanisms in tungsten-copper pseudoalloy

International Nuclear Information System (INIS)

Babak, A.V.; Gopkalo, E.E.; Krasovskij, A.Ya.; Nadezhdin, G.N.; Uskov, E.I.

1988-01-01

Results of the mechanical- and-physical study of peculiarities of the tungsten-copper pseudoalloy fracture in the temperature range of 293-2273 K are presented. It is shown that the studied material possesses maximum crack resistance in the vicinity of the upper temperature range boundary of the ductile-brittle transition and minimum resistance to cracks propagation when it contains melted copper. It is established that the peculiarities of changes in crack-resistance correspond to peculiarities of fracture micromechanisms for tungsten-copper pseudoalloy in the studied tempearture range

Self-Sensing of Single Carbon Fiber/Carbon Nanotube-Epoxy Composites Using Electro-Micromechanical Techniques and Acoustic Emission

International Nuclear Information System (INIS)

Park, Joung Man; Jang, Jung Hoon; Wang, Zuo Jia; Kwon, Dong Jun; Park, Jong Kyu; Lee, Woo Il

2010-01-01

Self-sensing on micro-failure, dispersion degree and relating properties, of carbon nanotube(CNT)/epoxy composites, were investigated using wettability, electro-micromechanical technique with acoustic emission(AE). Specimens were prepared from neat epoxy as well as composites with untreated and acid-treated CNT. Degree of dispersion was evaluated comparatively by measuring volumetric electrical resistivity and its standard deviation. Apparent modulus containing the stress transfer was higher for acid-treated CNT composite than for the untreated case. Applied cyclic loading responded well for a single carbon fiber/CNT-epoxy composite by the change in contact resistivity. The interfacial shear strength between a single carbon fiber and CNT-epoxy, determined in a fiber pullout test, was lower than that between a single carbon fiber and neat epoxy. Regarding on micro-damage sensing using electrical resistivity measurement with AE, the stepwise increment in electrical resistivity was observed for a single carbon fiber/CNT-epoxy composite. On the other hand, electrical resistivity increased infinitely right after the first carbon fiber breaks for a single carbon fiber/neat epoxy composite. The occurrence of AE events of added CNT composites was much higher than the neat epoxy case, due to microfailure at the interfaces by added CNTs

Radiation effects in concrete for nuclear power plants, Part II: Perspective from micromechanical modeling

Energy Technology Data Exchange (ETDEWEB)

Le Pape, Y., E-mail: lepapeym@ornl.gov; Field, K.G.; Remec, I.

2015-02-15

Highlights: • A micromechanical model for irradiated concrete is proposed. • Confrontation with literature data is successful. • Neutron radiation-induced volumetric expansion is a predominant degradation mode. • The nature of the aggregate alters the severity of damage to irradiated concrete. - Abstract: The need to understand and characterize the effects of neutron irradiation on concrete has become urgent because of the possible extension of service life of many nuclear power generating stations. Current knowledge is primarily based on a collection of data obtained in test reactors. These data are inherently difficult to interpret because materials and testing conditions are inconsistent. A micromechanical approach based on the Hashin composite sphere model is presented to derive a first-order separation of the effects of radiation on cement paste and aggregate, and, also, on their interaction. Although the scarcity of available data limits the validation of the model, it appears that, without negating a possible gamma-ray induced effect, the neutron-induced damage and swelling of aggregate plays a predominant role on the overall concrete expansion and the damage of the cement paste. The radiation-induced volumetric expansion (RIVE) effects can also be aided by temperature elevation and shrinkage in the cement paste.

Radiation effects in concrete for nuclear power plants, Part II: Perspective from micromechanical modeling

International Nuclear Information System (INIS)

Le Pape, Y.; Field, K.G.; Remec, I.

2015-01-01

Highlights: • A micromechanical model for irradiated concrete is proposed. • Confrontation with literature data is successful. • Neutron radiation-induced volumetric expansion is a predominant degradation mode. • The nature of the aggregate alters the severity of damage to irradiated concrete. - Abstract: The need to understand and characterize the effects of neutron irradiation on concrete has become urgent because of the possible extension of service life of many nuclear power generating stations. Current knowledge is primarily based on a collection of data obtained in test reactors. These data are inherently difficult to interpret because materials and testing conditions are inconsistent. A micromechanical approach based on the Hashin composite sphere model is presented to derive a first-order separation of the effects of radiation on cement paste and aggregate, and, also, on their interaction. Although the scarcity of available data limits the validation of the model, it appears that, without negating a possible gamma-ray induced effect, the neutron-induced damage and swelling of aggregate plays a predominant role on the overall concrete expansion and the damage of the cement paste. The radiation-induced volumetric expansion (RIVE) effects can also be aided by temperature elevation and shrinkage in the cement paste

Activation barrier scaling and crossover for noise-induced switching in micromechanical parametric oscillators.

Science.gov (United States)

Chan, H B; Stambaugh, C

2007-08-10

We explore fluctuation-induced switching in parametrically driven micromechanical torsional oscillators. The oscillators possess one, two, or three stable attractors depending on the modulation frequency. Noise induces transitions between the coexisting attractors. Near the bifurcation points, the activation barriers are found to have a power law dependence on frequency detuning with critical exponents that are in agreement with predicted universal scaling relationships. At large detuning, we observe a crossover to a different power law dependence with an exponent that is device specific.

Micromechanisms of fracture and fatigue in Ti3Al based and TiAl based intermetallics

International Nuclear Information System (INIS)

James, A.W.; Chave, R.A.; Hippsley, C.A.; Bowen, P.

1993-01-01

Micromechanisms of fracture and fatigue crack growth resistance in specific Ti 3 Al based and TiAl based intermetallics are reviewed. Effects of test temperature, environment and microstructure on crack growth resistance are considered in detail for several Ti 3 Al and Ti'Al based intermetallic systems under development. The implications of these studies for the structural reliability of these materials is also addressed briefly. (orig.)

[Coupled Analysis of Fluid-Structure Interaction of a Micro-Mechanical Valve for Glaucoma Drainage Devices].

Science.gov (United States)

Siewert, S; Sämann, M; Schmidt, W; Stiehm, M; Falke, K; Grabow, N; Guthoff, R; Schmitz, K-P

2015-12-01

Glaucoma is the leading cause of irreversible blindness worldwide. In therapeutically refractory cases, alloplastic glaucoma drainage devices (GDD) are being increasingly used to decrease intraocular pressure. Current devices are mainly limited by fibrotic encapsulation and postoperative hypotension. Preliminary studies have described the development of a glaucoma microstent to control aqueous humour drainage from the anterior chamber into the suprachoroidal space. One focus of these studies was on the design of a micro-mechanical valve placed in the anterior chamber to inhibit postoperative hypotension. The present report describes the coupled analysis of fluid-structure interaction (FSI) as basis for future improvements in the design micro-mechanical valves. FSI analysis was carried out with ANSYS 14.5 software. Solid and fluid geometry were combined in a model, and the corresponding material properties of silicone (Silastic Rx-50) and water at room temperature were assigned. The meshing of the solid and fluid domains was carried out in accordance with the results of a convergence study with tetrahedron elements. Structural and fluid mechanical boundary conditions completed the model. The FSI analysis takes into account geometric non-linearity and adaptive remeshing to consider changing geometry. A valve opening pressure of 3.26 mmHg was derived from the FSI analysis and correlates well with the results of preliminary experimental fluid mechanical studies. Flow resistance was calculated from non-linear pressure-flow characteristics as 8.5 × 10(-3) mmHg/µl  · min(-1) and 2.7 × 10(-3) mmHg/µl  · min(-1), respectively before and after valve opening pressure is exceeded. FSI analysis indicated leakage flow before valve opening, which is due to the simplified model geometry. The presented bidirectional coupled FSI analysis is a powerful tool for the development of new designs of micro-mechanical valves for GDD and may help to minimise the time and cost

Microstructural and micromechanical tests of titanium biomaterials intended for prosthetic reconstructions.

Science.gov (United States)

Ryniewicz, Anna M; Bojko, Łukasz; Ryniewicz, Wojciech I

2016-01-01

The aim of the present paper was a question of structural identification and evaluation of strength parameters of Titanium (Ticp - grade 2) and its alloy (Ti6Al4V) which are used to serve as a base for those permanent prosthetic supplements which are later manufactured employing CAD/CAM systems. Microstructural tests of Ticp and Ti6Al4V were conducted using an optical microscope as well as a scanning microscope. Hardness was measured with the Vickers method. Micromechanical properties of samples: microhardness and Young's modulus value, were measured with the Oliver and Pharr method. Based on studies using optical microscopy it was observed that the Ticp from the milling technology had a single phase, granular microstructure. The Ti64 alloy had a two-phase, fine-grained microstructure with an acicular-lamellar character. The results of scanning tests show that titanium Ticp had a single phase structure. On its grain there was visible acicular martensite. The structure of the two phase Ti64 alloy consists of a β matrix as well as released α phase deposits in the shape of extended needles. Micromechanical tests demonstrated that the alloy of Ti64 in both methods showed twice as high the microhardness as Ticp. In studies of Young's modulus of Ti64 alloy DMLS technology have lower value than titanium milling technology. According to the results obtained, the following conclusion has been drawn: when strength aspect is discussed, the DMLS method is a preferred one in manufacturing load structures in dentistry and may be an alternate way for the CAD/CAM system used in decrement processing.

Failure probability analyses for PWSCC in Ni-based alloy welds

International Nuclear Information System (INIS)

Udagawa, Makoto; Katsuyama, Jinya; Onizawa, Kunio; Li, Yinsheng

2015-01-01

A number of cracks due to primary water stress corrosion cracking (PWSCC) in pressurized water reactors and Ni-based alloy stress corrosion cracking (NiSCC) in boiling water reactors have been detected around Ni-based alloy welds. The causes of crack initiation and growth due to stress corrosion cracking include weld residual stress, operating stress, the materials, and the environment. We have developed the analysis code PASCAL-NP for calculating the failure probability and assessment of the structural integrity of cracked components on the basis of probabilistic fracture mechanics (PFM) considering PWSCC and NiSCC. This PFM analysis code has functions for calculating the incubation time of PWSCC and NiSCC crack initiation, evaluation of crack growth behavior considering certain crack location and orientation patterns, and evaluation of failure behavior near Ni-based alloy welds due to PWSCC and NiSCC in a probabilistic manner. Herein, actual plants affected by PWSCC have been analyzed using PASCAL-NP. Failure probabilities calculated by PASCAL-NP are in reasonable agreement with the detection data. Furthermore, useful knowledge related to leakage due to PWSCC was obtained through parametric studies using this code

Testing the permeability and corrosion resistance of micro-mechanically interlocked joints

DEFF Research Database (Denmark)

Byskov-Nielsen, Jeppe; Holm, Allan Hjarbæk; Højsholt, Rune

2011-01-01

Micro-mechanical interlocking (MMI) can be applied to create new and interesting composite materials. We have employed laser structuring to achieve MMI between stainless steel and plastic with extremely high joint strength. However, the water permeability and corrosion resistance of the joint must...... is conducted. The permeability seems to be consistent with the Hagen–Poiseuille equation independent of the laser structuring technique and is orders of magnitudes larger than the diffusion rate through the plastic. Two different types of corrosion tests have been undertaken, and we show that care must...... be taken in order not to degrade the corrosion resistance of the sample to an unacceptable level....

Micro-mechanics of ionic electroactive polymer actuators

Science.gov (United States)

Punning, Andres; Põldsalu, Inga; Kaasik, Friedrich; Vunder, Veiko; Aabloo, Alvo

2015-04-01

Commonly, modeling of the bending behavior of the ionic electroactive polymer (IEAP) actuators is based on the classical mechanics of cantilever beam. It is acknowledged, that the actuation of the ionic electroactive polymer (IEAP) actuators is symmetric about the centroid - the convex side of the actuator is expanding and the concave side is contracting for exactly the same amount, while the thickness of the actuator remains invariant. Actuating the IEAP actuators and sensors under scanning electron microscope (SEM), in situ, reveals that for some types of them this approach is incorrect. Comparison of the SEM micrographs using the Digital Image Correction (DIC) method results with the precise strain distribution of the IEAP actuators in two directions: in the axial direction, and in the direction of thickness. This information, in turn, points to the physical processes taking place within the electrodes as well as membrane of the trilayer laminate of sub-millimeter thickness. Comparison of the EAP materials, engaged as an actuator as well as a sensor, reveals considerable differences between the micro-mechanics of the two modes.

On the relevance of the micromechanics approach for predicting the linear viscoelastic behavior of semi-crystalline poly(ethylene)terephtalates (PET)

International Nuclear Information System (INIS)

Diani, J.; Bedoui, F.; Regnier, G.

2008-01-01

The relevance of micromechanics modeling to the linear viscoelastic behavior of semi-crystalline polymers is studied. For this purpose, the linear viscoelastic behaviors of amorphous and semi-crystalline PETs are characterized. Then, two micromechanics modeling methods, which have been proven in a previous work to apply to the PET elastic behavior, are used to predict the viscoelastic behavior of three semi-crystalline PETs. The microstructures of the crystalline PETs are clearly defined using WAXS techniques. Since microstructures and mechanical properties of both constitutive phases (the crystalline and the amorphous) are defined, the simulations are run without adjustable parameters. Results show that the models are unable to reproduce the substantial decrease of viscosity induced by the increase of crystallinity. Unlike the real materials, for moderate crystallinity, both models show materials of viscosity nearly identical to the amorphous material

A thermomechanical constitutive model for cemented granular materials with quantifiable internal variables. Part II - Validation and localization analysis

Science.gov (United States)

Das, Arghya; Tengattini, Alessandro; Nguyen, Giang D.; Viggiani, Gioacchino; Hall, Stephen A.; Einav, Itai

2014-10-01

We study the mechanical failure of cemented granular materials (e.g., sandstones) using a constitutive model based on breakage mechanics for grain crushing and damage mechanics for cement fracture. The theoretical aspects of this model are presented in Part I: Tengattini et al. (2014), A thermomechanical constitutive model for cemented granular materials with quantifiable internal variables, Part I - Theory (Journal of the Mechanics and Physics of Solids, 10.1016/j.jmps.2014.05.021). In this Part II we investigate the constitutive and structural responses of cemented granular materials through analyses of Boundary Value Problems (BVPs). The multiple failure mechanisms captured by the proposed model enable the behavior of cemented granular rocks to be well reproduced for a wide range of confining pressures. Furthermore, through comparison of the model predictions and experimental data, the micromechanical basis of the model provides improved understanding of failure mechanisms of cemented granular materials. In particular, we show that grain crushing is the predominant inelastic deformation mechanism under high pressures while cement failure is the relevant mechanism at low pressures. Over an intermediate pressure regime a mixed mode of failure mechanisms is observed. Furthermore, the micromechanical roots of the model allow the effects on localized deformation modes of various initial microstructures to be studied. The results obtained from both the constitutive responses and BVP solutions indicate that the proposed approach and model provide a promising basis for future theoretical studies on cemented granular materials.

Multiscale mechanics of TRIP-assisted multiphase steels: II. Micromechanical modelling

International Nuclear Information System (INIS)

Lani, F.; Furnemont, Q.; Van Rompaey, T.; Delannay, F.; Jacques, P.J.; Pardoen, T.

2007-01-01

The stress and strain partitioning between the different phases of transformation-induced plasticity (TRIP)-aided multiphase steels is evaluated using a mean field homogenization approach. The change of the austenite volume fraction under straining is predicted using a micromechanics-based criterion for the martensitic transformation adapted to the case of small, isolated, transforming austenite grains. The parameters of the model are identified from the mechanical response and transformation kinetics measured under uniaxial tension for two steels differing essentially by the austenite stability. The model is validated by comparing the predictions with tests performed under different loading conditions: pure shear, intermediate biaxial and equibiaxial. An analysis of the effect of the austenite stability on strength and ductility provides guidelines for optimizing properties according to the stress state

Effect of artificial toothbrushing and water storage on the surface roughness and micromechanical properties of tooth-colored CAD-CAM materials.

Science.gov (United States)

Flury, Simon; Diebold, Elisabeth; Peutzfeldt, Anne; Lussi, Adrian

2017-06-01

Because of the different composition of resin-ceramic computer-aided design and computer-aided manufacturing (CAD-CAM) materials, their polishability and their micromechanical properties vary. Moreover, depending on the composition of the materials, their surface roughness and micromechanical properties are likely to change with time. The purpose of this in vitro study was to investigate the effect of artificial toothbrushing and water storage on the surface roughness (Ra and Rz) and the micromechanical properties, surface hardness (Vickers [VHN]) and indentation modulus (E IT ), of 5 different tooth-colored CAD-CAM materials when polished with 2 different polishing systems. Specimens (n=40 per material) were cut from a composite resin (Paradigm MZ100; 3M ESPE), a feldspathic ceramic (Vitablocs Mark II; Vita Zahnfabrik), a resin nanoceramic (Lava Ultimate; 3M ESPE), a hybrid dental ceramic (Vita Enamic; Vita Zahnfabrik), and a nanocomposite resin (Ambarino High-Class; Creamed). All specimens were roughened in a standardized manner and polished either with Sof-Lex XT discs or the Vita Polishing Set Clinical. Surface roughness, VHN, and E IT were measured after polishing and after storage for 6 months (tap water, 37°C) with periodic, artificial toothbrushing. The surface roughness, VHN, and E IT results were analyzed with a nonparametric ANOVA followed by Kruskal-Wallis and exact Wilcoxon rank sum tests (α=.05). Irrespective of polishing system and of artificial toothbrushing and storage, Lava Ultimate generally showed the lowest surface roughness and Vitablocs Mark II the highest. As regards micromechanical properties, the following ranking of the CAD-CAM materials was found (from highest VHN/E IT to lowest VHN/E IT ): Vitablocs Mark II > Vita Enamic > Paradigm MZ100 > Lava Ultimate > Ambarino High-Class. Irrespective of material and of artificial toothbrushing and storage, polishing with Sof-Lex XT discs resulted in lower surface roughness than the Vita Polishing

Failure analysis and failure prevention in electric power systems

International Nuclear Information System (INIS)

Rau, C.A. Jr.; Becker, D.G.; Besuner, P.M.; Cipolla, R.C.; Egan, G.R.; Gupta, P.; Johnson, D.P.; Omry, U.; Tetelman, A.S.; Rettig, T.W.; Peters, D.C.

1977-01-01

New methods have been developed and applied to better quantify and increase the reliability, safety, and availability of electric power plants. Present and potential problem areas have been identified both by development of an improved computerized data base of malfunctions in nuclear power plants and by detailed metallurgical and mechanical failure analyses of selected problems. Significant advances in the accuracy and speed of structural analyses have been made through development and application of the boundary integral equation and influence function methods of stress and fracture mechanics analyses. The currently specified flaw evaluation procedures of the ASME Boiler and Pressure Vessel Code have been computerized. Results obtained from these procedures for evaluation of specific in-service inspection indications have been compared with results obtained utilizing the improved analytical methods. Mathematical methods have also been developed to describe and analyze the statistical variations in materials properties and in component loading, and uncertainties in the flaw size that might be passed by quality assurance systems. These new methods have been combined to develop accurate failure rate predictions based upon probabilistic fracture mechanics. Improved failure prevention strategies have been formulated by combining probabilistic fracture mechanics and cost optimization techniques. The approach has been demonstrated by optimizing the nondestructive inspection level with regard to both reliability and cost. (Auth.)

Bio-Inspired Micromechanical Directional Acoustic Sensor

Science.gov (United States)

Swan, William; Alves, Fabio; Karunasiri, Gamani

Conventional directional sound sensors employ an array of spatially separated microphones and the direction is determined using arrival times and amplitudes. In nature, insects such as the Ormia ochracea fly can determine the direction of sound using a hearing organ much smaller than the wavelength of sound it detects. The fly's eardrums are mechanically coupled, only separated by about 1 mm, and have remarkable directional sensitivity. A micromechanical sensor based on the fly's hearing system was designed and fabricated on a silicon on insulator (SOI) substrate using MEMS technology. The sensor consists of two 1 mm2 wings connected using a bridge and to the substrate using two torsional legs. The dimensions of the sensor and material stiffness determine the frequency response of the sensor. The vibration of the wings in response to incident sound at the bending resonance was measured using a laser vibrometer and found to be about 1 μm/Pa. The electronic response of the sensor to sound was measured using integrated comb finger capacitors and found to be about 25 V/Pa. The fabricated sensors showed good directional sensitivity. In this talk, the design, fabrication and characteristics of the directional sound sensor will be described. Supported by ONR and TDSI.

A micromechanical approach of suffusion based on a length scale analysis of the grain detachment and grain transport processes.

Science.gov (United States)

Wautier, Antoine; Bonelli, Stéphane; Nicot, François

2017-06-01

Suffusion is the selective erosion of the finest particles of a soil subjected to an internal flow. Among the four types of internal erosion and piping identified today, suffusion is the least understood. Indeed, there is a lack of micromechanical approaches for identifying the critical microstructural parameters responsible for this process. Based on a discrete element modeling of non cohesive granular assemblies, specific micromechanical tools are developed in a unified framework to account for the two first steps of suffusion, namely the grain detachment and the grain transport processes. Thanks to the use of an enhanced force chain definition and autocorrelation functions the typical lengths scales associated with grain detachment are characterized. From the definition of transport paths based on a graph description of the pore space the typical lengths scales associated with grain transport are recovered. For a uniform grain size distribution, a separation of scales between these two processes exists for the finest particles of a soil

Corrosion failure analysis as related to prevention of corrosion failures

International Nuclear Information System (INIS)

Suss, H.

1977-10-01

The factors and conditions which have contributed to many of the corrosion related service failures are discussed based on a review of actual case histories. The anti-corrosion devices which developed as a result of these failure analyses are reviewed, and the method which must be adopted and used to take advantage of the available corrosion prevention techniques is discussed

Mechanisms of dynamic deformation and dynamic failure in aluminum nitride

International Nuclear Information System (INIS)

Hu Guangli; Chen, C.Q.; Ramesh, K.T.; McCauley, J.W.

2012-01-01

Uniaxial quasi-static, uniaxial dynamic and confined dynamic compression experiments have been performed to characterize the failure and deformation mechanisms of a sintered polycrystalline aluminum nitride using a servohydraulic machine and a modified Kolsky bar. Scanning electron microscopy and transmission electron microscopy (TEM) are used to identify the fracture and deformation mechanisms under high rate and high pressure loading conditions. These results show that the fracture mechanisms are strong functions of confining stress and strain rate, with transgranular fracture becoming more common at high strain rates. Dynamic fracture mechanics and micromechanical models are used to analyze the observed fracture mechanisms. TEM characterization of fragments from the confined dynamic experiments shows that at higher pressures dislocation motion becomes a common dominant deformation mechanism in AlN. Prismatic slip is dominant, and pronounced microcrack–dislocation interactions are observed, suggesting that the dislocation plasticity affects the macroscopic fracture behavior in this material under high confining stresses.

Micromechanical experimental analysis and modelling of elastic and damageable behaviour of unidirectional SiC/SiC composites

International Nuclear Information System (INIS)

Chateau, C.

2011-01-01

Because of their potential use as a cladding material in future nuclear reactors, the complex mechanical behavior of SiC/SiC composites, which combines damage and anisotropy, must be understood and predictable. As part of a multi-scale approach, this work focuses on the first scale change: from the elementary constituents to the tow. Micromechanical approaches are implemented to describe the macroscopic behavior of the tow taking into account its microstructure heterogeneity and damage mechanisms occurring at the local scale. A representative virtual microstructure is generated based on a detailed microstructural investigation of the tow and its elastic response is studied by numerical homogenization. In addition to addressing the mechanical RVE issue, this study highlights the significant effects of residual porosity on the transverse behavior of the tow, due to the matrix infiltration process. The longitudinal damage is being studied through mini-composites, for which the evolution of microscopic damage mechanisms (matrix cracks and fiber breaks) is experimentally analyzed (in-situ SEM and tomography tensile tests). The identification of interfacial parameters of a 1D statistical damage model is based on the experimental characterization. Conventional assumptions of such models can adequately describe matrix cracking at macro and micro scale. However it is necessary to change them to get a proper prediction of ultimate failure. (author) [fr

Micromechanics of non-active clays in saturated state and DEM modelling

Directory of Open Access Journals (Sweden)

Pagano Arianna Gea

2017-01-01

Full Text Available The paper presents a conceptual micromechanical model for 1-D compression behaviour of non-active clays in saturated state. An experimental investigation was carried out on kaolin clay samples saturated with fluids of different pH and dielectric permittivity. The effect of pore fluid characteristics on one-dimensional compressibility behaviour of kaolin was investigated. A three dimensional Discrete Element Method (DEM was implemented in order to simulate the response of saturated kaolin observed during the experiments. A complex contact model was introduced, considering both the mechanical and physico-chemical microscopic interactions between clay particles. A simple analysis with spherical particles only was performed as a preliminary step in the DEM study in the elastic regime.

Micro-Mechanical Voltage Tunable Fabry-Perot Filters Formed in (111) Silicon. Degree awarded by Colorado Univ., Boulder, CO

Science.gov (United States)

Patterson, James D.

1997-01-01

The MEMS (Micro-Electro-Mechanical-Systems) technology is quickly evolving as a viable means to combine micro-mechanical and micro-optical elements on the same chip. One MEMS technology that has recently gained attention by the research community is the micro-mechanical Fabry-Perot optical filter. A MEMS based Fabry-Perot consists of a vertically integrated structure composed of two mirrors separated by an air gap. Wavelength tuning is achieved by applying a bias between the two mirrors resulting in an attractive electrostatic force which pulls the mirrors closer. In this work, we present a new micro-mechanical Fabry-Perot structure which is simple to fabricate and is integratable with low cost silicon photodetectors and transistors. The structure consists of a movable gold coated oxide cantilever for the top mirror and a stationary Au/Ni plated silicon bottom mirror. The fabrication process is single mask level, self aligned, and requires only one grown or deposited layer. Undercutting of the oxide cantilever is carried out by a combination of RIE and anisotropic KOH etching of the (111) silicon substrate. Metallization of the mirrors is provided by thermal evaporation and electroplating. The optical and electrical characteristics of the fabricated devices were studied and show promissing results. A wavelength shift of 120nm with 53V applied bias was demonstrated by one device geometry using 6.27 micrometer air gap. The finesse of the structure was 2.4. Modulation bandwidths ranging from 91KHz to greater than 920KHz were also observed. Theoretical calculations show that if mirror reflectivity, smoothness, and parallelism are improved, a finesse of 30 is attainable. The predictions also suggest that a reduction of the air gap to 1 micrometer results in an increased wavelength tuning range of 175 nm with a CMOS compatible 4.75V.

Micromechanical simulation of Uranium dioxide polycrystalline aggregate behaviour under irradiation

International Nuclear Information System (INIS)

Pacull, J.

2011-02-01

In pressurized water nuclear power reactor (PWR), the fuel rod is made of dioxide of uranium (UO 2 ) pellet stacked in a metallic cladding. A multi scale and multi-physic approaches are needed for the simulation of fuel behavior under irradiation. The main phenomena to take into account are thermomechanical behavior of the fuel rod and chemical-physic behavior of the fission products. These last years one of the scientific issue to improve the simulation is to take into account the multi-physic coupling problem at the microscopic scale. The objective of this ph-D study is to contribute to this multi-scale approach. The present work concerns the micro-mechanical behavior of a polycrystalline aggregate of UO 2 . Mean field and full field approaches are considered. For the former and the later a self consistent homogenization technique and a periodic Finite Element model base on the 3D Voronoi pattern are respectively used. Fuel visco-plasticity is introduced in the model at the scale of a single grain by taking into account specific dislocation slip systems of UO 2 . A cohesive zone model has also been developed and implemented to simulate grain boundary sliding and intergranular crack opening. The effective homogenous behaviour of a Representative Volume Element (RVE) is fitted with experimental data coming from mechanical tests on a single pellet. Local behavior is also analyzed in order to evaluate the model capacity to assess micro-mechanical state. In particular, intra and inter granular stress gradient are discussed. A first validation of the local behavior assessment is proposed through the simulation of intergranular crack opening measured in a compressive creep test of a single fuel pellet. Concerning the impact of the microstructure on the fuel behavior under irradiation, a RVE simulation with a representative transient loading of a fuel rod during a power ramp test is achieved. The impact of local stress and strain heterogeneities on the multi

Moisture-related mechanical properties of softwood: 3D micromechanical modeling

DEFF Research Database (Denmark)

Qing, Hai; Mishnaevsky, Leon

2009-01-01

Computational micromechanical analysis of the influence of moisture, density and microstructure of latewood on its hydroelastic and shrinkage properties is carried out. The elastic properties of cell sublayers have been determined using the unit cell models as for fiber reinforced composites (two....... The results for elastic properties of cell sublayers obtained from the unit cell models, from the self-consistent method and Halpin-Tsai equations are compared, and good agreement between these methods was observed. A computational technique, based on the representation of moisture effect as equivalent...... temperature-caused effects, has been developed and employed to the modeling of the moisture-related changes of the elastic properties of cell layers. A series of computational experiments have been carried out. In the simulations, it was observed that the shrinkage coefficients of longitudinal direction...

Micromechanical modeling of tungsten-based bulk metallic glass matrix composites

Energy Technology Data Exchange (ETDEWEB)

Li Hao [Department of Mechanical Engineering-Engineering Mechanics, Michigan Technological University, 1400 Townsend Drive, Houghton, MI 49931 (United States); Li Ke [Department of Mechanical Engineering, Texas A and M University, TAMU 3123, College Station, TX 77843 (United States)]. E-mail: keli@tamu.edu; Subhash, Ghatu [Department of Mechanical Engineering-Engineering Mechanics, Michigan Technological University, 1400 Townsend Drive, Houghton, MI 49931 (United States); Kecskes, Laszlo J. [Weapons and Materials Research Directorate, US Army Research Laboratory, Aberdeen Proving Ground, MD 21005 (United States); Dowding, Robert J. [Weapons and Materials Research Directorate, US Army Research Laboratory, Aberdeen Proving Ground, MD 21005 (United States)

2006-08-15

Micromechanics models are developed for tungsten (W)-based bulk metallic glass (BMG) matrix composites employing the Voronoi tessellation technique and the finite element (FE) method. The simulation results indicate that the computed elastic moduli are close to those measured in the experiments. The predicted stress-strain curves agree well with their experimentally obtained counterparts in the early stage of the plastic deformation. An increase in the W volume fraction leads to a decrease in the yield stress and an increase in the Young's modulus of the composite. In addition, contours of equivalent plastic strain for increasing applied strains provide an explanation why shear bands were observed in the glassy phase, along the W/BMG interface, and in the W phase of failed W/BMG composite specimens.

Micromechanical modeling of rate-dependent behavior of Connective tissues.

Science.gov (United States)

Fallah, A; Ahmadian, M T; Firozbakhsh, K; Aghdam, M M

2017-03-07

In this paper, a constitutive and micromechanical model for prediction of rate-dependent behavior of connective tissues (CTs) is presented. Connective tissues are considered as nonlinear viscoelastic material. The rate-dependent behavior of CTs is incorporated into model using the well-known quasi-linear viscoelasticity (QLV) theory. A planar wavy representative volume element (RVE) is considered based on the tissue microstructure histological evidences. The presented model parameters are identified based on the available experiments in the literature. The presented constitutive model introduced to ABAQUS by means of UMAT subroutine. Results show that, monotonic uniaxial test predictions of the presented model at different strain rates for rat tail tendon (RTT) and human patellar tendon (HPT) are in good agreement with experimental data. Results of incremental stress-relaxation test are also presented to investigate both instantaneous and viscoelastic behavior of connective tissues. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Effect of Fiber Strength Stochastics and Local Fiber Volume Fraction on Multiscale Progressive Failure of Composites

Science.gov (United States)

Ricks, Trenton M.; Lacy, Jr., Thomas E.; Bednarcyk, Brett A.; Arnold, Steven M.

2013-01-01

Continuous fiber unidirectional polymer matrix composites (PMCs) can exhibit significant local variations in fiber volume fraction as a result of processing conditions that can lead to further local differences in material properties and failure behavior. In this work, the coupled effects of both local variations in fiber volume fraction and the empirically-based statistical distribution of fiber strengths on the predicted longitudinal modulus and local tensile strength of a unidirectional AS4 carbon fiber/ Hercules 3502 epoxy composite were investigated using the special purpose NASA Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC); local effective composite properties were obtained by homogenizing the material behavior over repeating units cells (RUCs). The predicted effective longitudinal modulus was relatively insensitive to small (8%) variations in local fiber volume fraction. The composite tensile strength, however, was highly dependent on the local distribution in fiber strengths. The RUC-averaged constitutive response can be used to characterize lower length scale material behavior within a multiscale analysis framework that couples the NASA code FEAMAC and the ABAQUS finite element solver. Such an approach can be effectively used to analyze the progressive failure of PMC structures whose failure initiates at the RUC level. Consideration of the effect of local variations in constituent properties and morphologies on progressive failure of PMCs is a central aspect of the application of Integrated Computational Materials Engineering (ICME) principles for composite materials.

Failure analysis for WWER-fuel elements

International Nuclear Information System (INIS)

Boehmert, J.; Huettig, W.

1986-10-01

If the fuel defect rate proves significantly high, failure analysis has to be performed in order to trace down the defect causes, to implement corrective actions, and to take measures of failure prevention. Such analyses are work-consuming and very skill-demanding technical tasks, which require examination methods and devices excellently developed and a rich stock of experience in evaluation of features of damage. For that this work specifies the procedure of failure analyses in detail. Moreover prerequisites and experimental equipment for the investigation of WWER-type fuel elements are described. (author)

An analytical model for interactive failures

International Nuclear Information System (INIS)

Sun Yong; Ma Lin; Mathew, Joseph; Zhang Sheng

2006-01-01

In some systems, failures of certain components can interact with each other, and accelerate the failure rates of these components. These failures are defined as interactive failure. Interactive failure is a prevalent cause of failure associated with complex systems, particularly in mechanical systems. The failure risk of an asset will be underestimated if the interactive effect is ignored. When failure risk is assessed, interactive failures of an asset need to be considered. However, the literature is silent on previous research work in this field. This paper introduces the concepts of interactive failure, develops an analytical model to analyse this type of failure quantitatively, and verifies the model using case studies and experiments

Uncertainties and quantification of common cause failure rates and probabilities for system analyses

International Nuclear Information System (INIS)

Vaurio, Jussi K.

2005-01-01

Simultaneous failures of multiple components due to common causes at random times are modelled by constant multiple-failure rates. A procedure is described for quantification of common cause failure (CCF) basic event probabilities for system models using plant-specific and multiple-plant failure-event data. Methodology is presented for estimating CCF-rates from event data contaminated with assessment uncertainties. Generalised impact vectors determine the moments for the rates of individual systems or plants. These moments determine the effective numbers of events and observation times to be input to a Bayesian formalism to obtain plant-specific posterior CCF-rates. The rates are used to determine plant-specific common cause event probabilities for the basic events of explicit fault tree models depending on test intervals, test schedules and repair policies. Three methods are presented to determine these probabilities such that the correct time-average system unavailability can be obtained with single fault tree quantification. Recommended numerical values are given and examples illustrate different aspects of the methodology

Failure analysis of buried tanks

International Nuclear Information System (INIS)

Watkins, R.K.

1994-01-01

Failure of a buried tank can be hazardous. Failure may be a leak through which product is lost from the tank; but also through which contamination can occur. Failures are epidemic -- because buried tanks are out of sight, but also because designers of buried tanks have adopted analyses developed for pressure tanks. So why do pressure tanks fail when they are buried? Most failures of buried tanks are really soil failures. Soil compresses, or slips, or liquefies. Soil is not only a load, it is a support without which the tank deforms. A high water table adds to the load on the tank. It also reduces the strength of the soil. Based on tests, structural analyses are proposed for empty tanks buried in soils of various quality, with the water table at various levels, and with internal vacuum. Failure may be collapse tank. Such collapse is a sudden, audible inversion of the cylinder when the sidefill soil slips. Failure may be flotation. Failure may be a leak. Most leaks are fractures in the welds in overlap seams at flat spots. Flat spots are caused by a hard bedding or a heavy surface wheel load. Because the tank wall is double thick at the overlap, shearing stress in the weld is increased. Other weld failures occur when an end plate shears down past a cylinder; or when the tank is supported only at its ends like a beam. These, and other, failures can be analyzed with justifiable accuracy using basic principles of mechanics of materials. 10 figs

Mechanics in Composite Materials and Process

International Nuclear Information System (INIS)

Lee, Dae Gil

1993-03-01

This book includes introduction of composite materials, stress, in-plane stiffness of laminates strain rate, ply stress, failure criterion and bending, composite materials micromechanics, composite plates and micromechanics of composite materials. It also deals with process of composite materials such as autoclave vacuum bag degassing process, connection of composite materials, filament winding process, resin transfer molding, sheet molding compound and compression molding.

Radiofrequency cold plasma nitrided carbon steel: Microstructural and micromechanical characterizations

International Nuclear Information System (INIS)

Bouanis, F.Z.; Bentiss, F.; Bellayer, S.; Vogt, J.B.; Jama, C.

2011-01-01

Highlights: → C38 carbon steel samples were plasma nitrided using a radiofrequency (rf) nitrogen plasma discharge. → RF plasma treatment enables nitriding for non-heated substrates. → The morphological and chemical analyses show the formation of a uniform thickness on the surface of the nitrided C38 steel. → Nitrogen plasma active species diffuse into the samples and lead to the formation of Fe x N. → The increase in microhardness values for nitrided samples with plasma processing time is interpreted by the formation of a thicker nitrided layer on the steel surface. - Abstract: In this work, C38 carbon steel was plasma nitrided using a radiofrequency (rf) nitrogen plasma discharge on non-heated substrates. General characterizations were performed to compare the chemical compositions, the microstructures and hardness of the untreated and plasma treated surfaces. The plasma nitriding was carried out on non-heated substrates at a pressure of 16.8 Pa, using N 2 gas. Surface characterizations before and after N 2 plasma treatment were performed by means of the electron probe microanalysis (EPMA), X-ray photoelectron spectroscopy (XPS) and Vickers microhardness measurements. The morphological and chemical analysis showed the formation of a uniform structure on the surface of the nitrided sample with enrichment in nitrogen when compared to untreated sample. The thickness of the nitride layer formed depends on the treatment time duration and is approximately 14 μm for 10 h of plasma treatment. XPS was employed to obtain chemical-state information of the plasma nitrided steel surfaces. The micromechanical results show that the surface microhardness increases as the plasma-processing time increases to reach, 1487 HV 0.005 at a plasma processing time of 8 h.

Radiofrequency cold plasma nitrided carbon steel: Microstructural and micromechanical characterizations

Energy Technology Data Exchange (ETDEWEB)

Bouanis, F.Z. [Universite Lille Nord de France, F-59000 Lille (France); Unite Materiaux et Transformations (UMET), Ingenierie des Systemes Polymeres, CNRS UMR 8207, ENSCL, BP 90108, F-59652 Villeneuve d' Ascq Cedex (France); Bentiss, F. [Laboratoire de Chimie de Coordination et d' Analytique, Faculte des Sciences, Universite Chouaib Doukkali, B.P. 20, M-24000 El Jadida (Morocco); Bellayer, S.; Vogt, J.B. [Universite Lille Nord de France, F-59000 Lille (France); Unite Materiaux et Transformations (UMET), Ingenierie des Systemes Polymeres, CNRS UMR 8207, ENSCL, BP 90108, F-59652 Villeneuve d' Ascq Cedex (France); Jama, C., E-mail: charafeddine.jama@ensc-lille.fr [Universite Lille Nord de France, F-59000 Lille (France); Unite Materiaux et Transformations (UMET), Ingenierie des Systemes Polymeres, CNRS UMR 8207, ENSCL, BP 90108, F-59652 Villeneuve d' Ascq Cedex (France)

2011-05-16

Highlights: {yields} C38 carbon steel samples were plasma nitrided using a radiofrequency (rf) nitrogen plasma discharge. {yields} RF plasma treatment enables nitriding for non-heated substrates. {yields} The morphological and chemical analyses show the formation of a uniform thickness on the surface of the nitrided C38 steel. {yields} Nitrogen plasma active species diffuse into the samples and lead to the formation of Fe{sub x}N. {yields} The increase in microhardness values for nitrided samples with plasma processing time is interpreted by the formation of a thicker nitrided layer on the steel surface. - Abstract: In this work, C38 carbon steel was plasma nitrided using a radiofrequency (rf) nitrogen plasma discharge on non-heated substrates. General characterizations were performed to compare the chemical compositions, the microstructures and hardness of the untreated and plasma treated surfaces. The plasma nitriding was carried out on non-heated substrates at a pressure of 16.8 Pa, using N{sub 2} gas. Surface characterizations before and after N{sub 2} plasma treatment were performed by means of the electron probe microanalysis (EPMA), X-ray photoelectron spectroscopy (XPS) and Vickers microhardness measurements. The morphological and chemical analysis showed the formation of a uniform structure on the surface of the nitrided sample with enrichment in nitrogen when compared to untreated sample. The thickness of the nitride layer formed depends on the treatment time duration and is approximately 14 {mu}m for 10 h of plasma treatment. XPS was employed to obtain chemical-state information of the plasma nitrided steel surfaces. The micromechanical results show that the surface microhardness increases as the plasma-processing time increases to reach, 1487 HV{sub 0.005} at a plasma processing time of 8 h.

Improvement of interfacial adhesion and nondestructive damage evaluation for plasma-treated PBO and Kevlar fibers/epoxy composites using micromechanical techniques and surface wettability.

Science.gov (United States)

Park, Joung-Man; Kim, Dae-Sik; Kim, Sung-Ryong

2003-08-15

Comparison of interfacial properties and microfailure mechanisms of oxygen-plasma treated poly(p-phenylene-2,6-benzobisoxazole (PBO, Zylon) and poly(p-phenylene terephthalamide) (PPTA, Kevlar) fibers/epoxy composites were investigated using a micromechanical technique and nondestructive acoustic emission (AE). The interfacial shear strength (IFSS) and work of adhesion, Wa, of PBO or Kevlar fiber/epoxy composites increased with oxygen-plasma treatment, due to induced hydrogen and covalent bondings at their interface. Plasma-treated Kevlar fiber showed the maximum critical surface tension and polar term, whereas the untreated PBO fiber showed the minimum values. The work of adhesion and the polar term were proportional to the IFSS directly for both PBO and Kevlar fibers. The microfibril fracture pattern of two plasma-treated fibers appeared obviously. Unlike in slow cooling, in rapid cooling, case kink band and kicking in PBO fiber appeared, whereas buckling in the Kevlar fiber was observed mainly due to compressive and residual stresses. Based on the propagation of microfibril failure toward the core region, the number of AE events for plasma-treated PBO and Kevlar fibers increased significantly compared to the untreated case. The results of nondestructive AE were consistent with microfailure modes.

Root cause of failure analysis and the system engineer

International Nuclear Information System (INIS)

Coppock, M.S.; Hartwig, A.W.

1990-01-01

In an industry where ever-increasing emphasis is being placed on root cause of failure determination, it is imperative that a successful nuclear utility have an effective means of identifying failures and performing the necessary analyses. The current Institute of Nuclear Power Operations (INPO) good practice, OE-907, root-cause analysis, gives references to methodology that will help determine breakdowns in procedures, programs, or design but gives very little guidance on how or when to perform component root cause of failure analyses. The system engineers of nuclear utilities are considered the focal point for their respective systems and are required by most programs to investigate component failures. The problem that the system engineer faces in determining a component root cause of failures lies in acquisition of the necessary data to identify the need to perform the analysis and in having the techniques and equipment available to perform it. The system engineers at the Palo Verde nuclear generating station routinely perform detailed component root cause of failure analyses. The Palo Verde program provides the system engineers with the information necessary to identify when a component root cause of failure is required. Palo Verde also has the necessary equipment on-site to perform the analyses

Frequency division using a micromechanical resonance cascade

Energy Technology Data Exchange (ETDEWEB)

Qalandar, K. R., E-mail: kamala@engineering.ucsb.edu; Gibson, B.; Sharma, M.; Ma, A.; Turner, K. L. [Department of Mechanical Engineering, University of California at Santa Barbara, Santa Barbara, California 93106 (United States); Strachan, B. S. [Department of Mechanical Engineering, Michigan State University, East Lansing, Michigan 48823 (United States); Department of Electrical Engineering, Michigan State University, East Lansing, Michigan 48823 (United States); Shaw, S. W. [Department of Mechanical Engineering, Michigan State University, East Lansing, Michigan 48823 (United States); Department of Physics and Astronomy, Michigan State University, East Lansing, Michigan 48823 (United States)

2014-12-15

A coupled micromechanical resonator array demonstrates a mechanical realization of multi-stage frequency division. The mechanical structure consists of a set of N sequentially perpendicular microbeams that are connected by relatively weak elastic elements such that the system vibration modes are localized to individual microbeams and have natural frequencies with ratios close to 1:2:⋯:2{sup N}. Conservative (passive) nonlinear inter-modal coupling provides the required energy transfer between modes and is achieved by finite deformation kinematics. When the highest frequency beam is excited, this arrangement promotes a cascade of subharmonic resonances that achieve frequency division of 2{sup j} at microbeam j for j = 1, …, N. Results are shown for a capacitively driven three-stage divider in which an input signal of 824 kHz is passively divided through three modal stages, producing signals at 412 kHz, 206 kHz, and 103 kHz. The system modes are characterized and used to delineate the range of AC input voltages and frequencies over which the cascade occurs. This narrow band frequency divider has simple design rules that are scalable to higher frequencies and can be extended to a larger number of modal stages.

Remote quantum entanglement between two micromechanical oscillators.

Science.gov (United States)

Riedinger, Ralf; Wallucks, Andreas; Marinković, Igor; Löschnauer, Clemens; Aspelmeyer, Markus; Hong, Sungkun; Gröblacher, Simon

2018-04-01

Entanglement, an essential feature of quantum theory that allows for inseparable quantum correlations to be shared between distant parties, is a crucial resource for quantum networks 1 . Of particular importance is the ability to distribute entanglement between remote objects that can also serve as quantum memories. This has been previously realized using systems such as warm 2,3 and cold atomic vapours 4,5 , individual atoms 6 and ions 7,8 , and defects in solid-state systems 9-11 . Practical communication applications require a combination of several advantageous features, such as a particular operating wavelength, high bandwidth and long memory lifetimes. Here we introduce a purely micromachined solid-state platform in the form of chip-based optomechanical resonators made of nanostructured silicon beams. We create and demonstrate entanglement between two micromechanical oscillators across two chips that are separated by 20 centimetres . The entangled quantum state is distributed by an optical field at a designed wavelength near 1,550 nanometres. Therefore, our system can be directly incorporated in a realistic fibre-optic quantum network operating in the conventional optical telecommunication band. Our results are an important step towards the development of large-area quantum networks based on silicon photonics.

Finite deformation of incompressible fiber-reinforced elastomers: A computational micromechanics approach

Science.gov (United States)

Moraleda, Joaquín; Segurado, Javier; LLorca, Javier

2009-09-01

The in-plane finite deformation of incompressible fiber-reinforced elastomers was studied using computational micromechanics. Composite microstructure was made up of a random and homogeneous dispersion of aligned rigid fibers within a hyperelastic matrix. Different matrices (Neo-Hookean and Gent), fibers (monodisperse or polydisperse, circular or elliptical section) and reinforcement volume fractions (10-40%) were analyzed through the finite element simulation of a representative volume element of the microstructure. A successive remeshing strategy was employed when necessary to reach the large deformation regime in which the evolution of the microstructure influences the effective properties. The simulations provided for the first time "quasi-exact" results of the in-plane finite deformation for this class of composites, which were used to assess the accuracy of the available homogenization estimates for incompressible hyperelastic composites.

Effect of Discontinuities and Uncertainties on the Response and Failure of Composite Structures

Science.gov (United States)

Noor, Ahmed K.; Perry, Ferman W.; Poteat, Marcia M. (Technical Monitor)

2000-01-01

The overall goal of this research was to assess the effect of discontinuities and uncertainties on the nonlinear response and failure of composite structures subjected to combined mechanical and thermal loads. The four key elements of the study were: (1) development of simple and efficient procedures for the accurate determination of transverse shear and transverse normal stresses in structural sandwiches as well as in unstiffened and stiffened composite panels and shells; (2) study the effects of transverse stresses on the response, damage initiation and propagation in composite and sandwich structures; (3) use of hierarchical sensitivity coefficients to identify the major parameters that affect the response and damage in each of the different levels in the hierarchy (micro-mechanical, layer, panel, subcomponent and component levels); and (4) application of fuzzy set techniques to identify the range and variation of possible responses. The computational models developed were used in conjunction with experiments, to understand the physical phenomena associated with the nonlinear response and failure of composite and sandwich structures. A toolkit was developed for use in conjunction with deterministic analysis programs to help the designer in assessing the effect of uncertainties in the different computational model parameters on the variability of the response quantities.

A micromechanical interpretation of the temperature dependence of Beremin model parameters for French RPV steel

International Nuclear Information System (INIS)

Mathieu, Jean-Philippe; Inal, Karim; Berveiller, Sophie; Diard, Olivier

2010-01-01

Local approach to brittle fracture for low-alloyed steels is discussed in this paper. A bibliographical introduction intends to highlight general trends and consensual points of the topic and evokes debatable aspects. French RPV steel 16MND5 (equ. ASTM A508 Cl.3), is then used as a model material to study the influence of temperature on brittle fracture. A micromechanical modelling of brittle fracture at the elementary volume scale already used in previous work is then recalled. It involves a multiscale modelling of microstructural plasticity which has been tuned on experimental inter-phase and inter-granular stresses heterogeneities measurements. Fracture probability of the elementary volume can then be computed using a randomly attributed defect size distribution based on realistic carbides repartition. This defect distribution is then deterministically correlated to stress heterogeneities simulated within the microstructure using a weakest-link hypothesis on the elementary volume, which results in a deterministic stress to fracture. Repeating the process allows to compute Weibull parameters on the elementary volume. This tool is then used to investigate the physical mechanisms that could explain the already experimentally observed temperature dependence of Beremin's parameter for 16MND5 steel. It is showed that, assuming that the hypothesis made in this work about cleavage micro-mechanisms are correct, effective equivalent surface energy (i.e. surface energy plus plastically dissipated energy when blunting the crack tip) for propagating a crack has to be temperature dependent to explain Beremin's parameters temperature evolution.

micro-mechanical modeling and numerical simulation of creep in concrete taking into account the effects of micro-cracking and hygro-thermal

International Nuclear Information System (INIS)

Thai, M.Q.

2012-01-01

Concrete is a complex heterogeneous material whose deformations include a delayed part that is affected by a number of factors such as temperature, relative humidity and microstructure evolution. Taking into account differed deformations and in particular creep is essential in the computation of concrete structures such as those dedicated to radioactive waste storage. The present work aims: (1) at elaborating a simple and robust model of creep for concrete by using micro-mechanics and accounting for the effects of damage, temperature and relative humidity; (2) at numerically implementing the creep model developed in a finite element code so as to simulate the behavior of simple structural elements in concrete. To achieve this twofold objective, the present work is partitioned into three parts. In the first part the cement-based material at the microscopic scale is taken to consist of a linear viscoelastic matrix characterized by a generalized Maxwell model and of particulate phases representing elastic aggregates and pores. The Mori-Tanaka micro-mechanical scheme, the Laplace-Carson transform and its inversion are then used to obtain analytical or numerical estimates for the mechanical and hydro-mechanical parameters of the material. Next, the original micromechanical model of creep is coupled to the damage model of Mazars through the concept of pseudo-deformations introduced by Schapery. The parameters involved in the creep-damage model thus established are systematically identified using available experimental data. Finally, the effects of temperature and relative humidity are accounted for in the creep-damage model by using the equivalent time method; the efficiency of this approach is demonstrated and discussed in the case of simple creep tests. (author) [fr

Compressive failure model for fiber composites by kink band initiation from obliquely aligned, shear-dislocated fiber breaks

Energy Technology Data Exchange (ETDEWEB)

Bai, J.; Phoenix, S.L. [Cornell University, Ithaca, NY (United States). Dept. of Theoretical and Applied Mechanics

2005-04-01

Predicting compressive failure of a unidirectional fibrous composite is a longstanding and challenging problem that we study from a new perspective. Motivated by previous modelling of tensile failure as well as experimental observations on compressive failures in single carbon fibers, we develop a new micromechanical model for the compressive failure process in unidirectional, planar composites. As the compressive load is increased, random fiber failures are assumed to occur due to statistically distributed flaws, analogous to what occurs in tension. These breaks are often shear-mode failures with slanted surfaces that induce shear dislocations, especially when they occur in small groups aligned obliquely. Our model includes interactions of dislocated and neighboring intact fibers through a system of fourth-order, differential equations governing transverse deformation, and also allows for local matrix plastic yielding and debonding from the fiber near and within the dislocation arrays. Using the Discrete Fourier Transform method, we find a 'building-block' analytical solution form, which naturally embodies local length scales of fiber microbuckling and instability. Based on the influence function, superposition approach, a computationally efficient scheme is developed to model the evolution of fiber and matrix stresses. Under increasing compressive strain the simulations show that matrix yielding and debonding crucially lead to large increases in bending strains in fibers next to small groups of obliquely aligned, dislocated breaks. From the paired locations of maximum fiber bending in flanking fibers, the triggering of an unstable kink band becomes realistic. The geometric features of the kink band, such as the fragment lengths and orientation angles, will depend on the fiber and matrix mechanical and geometric properties. In carbon fiber-polymer matrix systems our model predicts a much lower compressive failure stress than obtained from Rosen

The failure of brittle materials under overall compression: Effects of loading rate and defect distribution

Science.gov (United States)

Paliwal, Bhasker

The constitutive behaviors and failure processes of brittle materials under far-field compressive loading are studied in this work. Several approaches are used: experiments to study the compressive failure behavior of ceramics, design of experimental techniques by means of finite element simulations, and the development of micro-mechanical damage models to analyze and predict mechanical response of brittle materials under far-field compression. Experiments have been conducted on various ceramics, (primarily on a transparent polycrystalline ceramic, aluminum oxynitride or AlON) under loading rates ranging from quasi-static (˜ 5X10-6) to dynamic (˜ 200 MPa/mus), using a servo-controlled hydraulic test machine and a modified compression Kolsky bar (MKB) technique respectively. High-speed photography has also been used with exposure times as low as 20 ns to observe the dynamic activation, growth and coalescence of cracks and resulting damage zones in the specimen. The photographs were correlated in time with measurements of the stresses in the specimen. Further, by means of 3D finite element simulations, an experimental technique has been developed to impose a controlled, homogeneous, planar confinement in the specimen. The technique can be used in conjunction with a high-speed camera to study the in situ dynamic failure behavior of materials under confinement. AlON specimens are used for the study. The statically pre-compressed specimen is subjected to axial dynamic compressive loading using the MKB. Results suggest that confinement not only increases the load carrying capacity, it also results in a non-linear stress evolution in the material. High-speed photographs also suggest an inelastic deformation mechanism in AlON under confinement which evolves more slowly than the typical brittle-cracking type of damage in the unconfined case. Next, an interacting micro-crack damage model is developed that explicitly accounts for the interaction among the micro-cracks in

Devices for measuring the capacitance of micromechanical sensors of mobile robots navigation systems and its deviation from the nominal value

Directory of Open Access Journals (Sweden)

Rudyk A.V.

2016-12-01

Full Text Available The article describes methods of constructing devices for measuring the capacitance of micromechanical sensors (accelerometers and gyros mobile robots navigation systems and its deviation from the nominal value. A modified diagram of a sigma-delta modulator is offered. It realizes a direct connection capacitive sensor connection to the sigma-delta converter, as a result increased resolution, accuracy and linearity of the conversion. This interface is insensitive to the value of capacitance between the sensor leads and common wire or leakage current to a common wire. Variants of expansion as the nominal of the test capacity and the range of conversion of the relative deviation of the nominal capacity using two integrators are offered. The versions of circuit implementation devices for measuring the capacitance deviation of a micromechanical sensor from the nominal value are designed on the basis of the completed integrated circuit AD7745 / AD7746 and AD7747 of Analog Devices, CAV414 / 424 firm Analog Microelectronics and precision analog microcontroller ADuCM360 / CM361 company ARM Limited.

Relations between morphology and micromechanical properties of alpha, beta and gamma phases of iPP

Czech Academy of Sciences Publication Activity Database

Šlouf, Miroslav; Pavlova, Ewa; Krejčíková, Sabina; Ostafinska, Aleksandra; Zhigunov, Alexander; Krzyžánek, Vladislav; Sowinski, P.; Piorkowska, E.

2018-01-01

Roč. 67, May (2018), s. 522-532 ISSN 0142-9418 R&D Projects: GA MZd(CZ) NV15-31269A; GA TA ČR(CZ) TE01020118; GA MŠk(CZ) LO1507 Grant - others:AV ČR(CZ) PAN-17-18 Program:Bilaterální spolupráce Institutional support: RVO:61389013 ; RVO:68081731 Keywords : polypropylene * gamma-phase * micromechanical properties Subject RIV: CD - Macromolecular Chemistry; JA - Electronics ; Optoelectronics, Electrical Engineering (UPT-D) OBOR OECD: Polymer science; Electrical and electronic engineering (UPT-D) Impact factor: 2.464, year: 2016

Micromechanical Model for Deformation in Solids with Universal Predictions for Stress-Strain Curves and Slip Avalanches

International Nuclear Information System (INIS)

Dahmen, Karin A.; Ben-Zion, Yehuda; Uhl, Jonathan T.

2009-01-01

A basic micromechanical model for deformation of solids with only one tuning parameter (weakening ε) is introduced. The model can reproduce observed stress-strain curves, acoustic emissions and related power spectra, event statistics, and geometrical properties of slip, with a continuous phase transition from brittle to ductile behavior. Exact universal predictions are extracted using mean field theory and renormalization group tools. The results agree with recent experimental observations and simulations of related models for dislocation dynamics, material damage, and earthquake statistics.

Micromechanical studies of cyclic creep fracture under stress controlled loading

DEFF Research Database (Denmark)

van der Giessen, Erik; Tvergaard, Viggo

1996-01-01

is based on numerical unit cell analyses for a planar polycrystal model with the grains and grain boundaries modeled individually, in order to investigate the interactions between the mechanisms involved and to account for the build-up of residual stress fields during cycling. The behaviour of a limiting......This paper deals with a study of intergranular failure by creep cavitation under stress-controlled cyclic loading conditions. Loading is assumed to be slow enough that diffusion and creep mechanisms (including grain boundary sliding) dominate, leading to intergranular creep fracture. This study...

Micromechanics of transformation-induced plasticity and variant coalescence

International Nuclear Information System (INIS)

Marketz, F.; Fischer, F.D.; University for Mining and Metallurgy, Leoben; Tanaka, K.

1996-01-01

Quantitative micromechanics descriptions of both transformation-induced plasticity (TRIP) associated with the martensitic transformation in an Fe-Ni alloy and of variant coalescence in a Cu-Al-Ni shape memory alloy are presented. The macroscopic deformation behavior of a polycrystalline aggregate as a result of the rearrangements within the crystallites is modelled with the help of a finite element based periodic microfield approach. In the case of TRIP the parent→martensite transformation is described by microscale thermodynamic and kinetic equations taking into account internal stress states. The simulation of a classical experiment on TRIP allows to quantify the Magee-effect and the Greenwood-Johnson effect. Furthermore, the development of the martensitic microstructure is studied with respect to the stress-assisted transformation of preferred variants. In the case of variant coalescence the strain energy due to internal stress states has an important influence on the mechanical behavior. Formulating the reorientation process on the size scale of self-accommodating plate groups in terms of the mobility of the boundaries between martensitic variants the macroscopic behavior in uniaxial tension is predicted by an incremental modelling procedure. Furthermore, influence of energy dissipation on the overall behavior is quantified. (orig.)

Multilevel modeling of micromechanics and phase formation for microstructural evolution of magnetic zones

International Nuclear Information System (INIS)

Suwa, Yoshihiro; Aizawa, Tatsuhiko; Takaya, Shigeru; Nagae, Yuji; Aoto, Kazumi

2005-03-01

The present research aims at a proposal of theoretical treatise to describe the local phase transformation from austenite to ferrite in the stainless steels under hot cyclic fatigue conditions. In experiments, this local phase transformation is detected as a magnetized region in the non-magnetic matrix after low-cycle fatigue test at the elevated temperature. The theoretical frame proposed here is composed of two methodologies. In the first approach, microstructure evolution with γ → α transformation is described by the phase field method. In the second approach, micromechanical method on the basis of the unit cell modeling is proposed to develop a new micromechanical analysis. The details of two approached are summarized in the following. (1) Phase formation simulation by the phase field method. Most of reports have started that γ-α phase transformation as a creep damage is induced by dechromization, which comes from carbide precipitation around grain boundaries. A new theoretical treatise is proposed for simulating this γ → α transformation in Fe-Cr-Ni system. Stabilities of both phases are investigated for various chemical compositions. Furthermore, in order to investigate dechromization phenomena in Fe-Cr-Ni-C system, a new theoretical frame is also proposed to handle an interstitial element in phase field method. (2) Low cycle fatigue elasto-plastic analysis by the unit-cell modeling. In experiments, the magnetized zones are generated to distribute at the vicinity of the hard, delta-phase inclusion in the austenitic matrix. The cumulative plastic region advances in the surroundings of this hard inclusion with increasing the number of cycles in the controlled strain range. This predicted profile of cumulative plastic regions corresponds to the experimentally measured, magnetized zones. In addition, the effect of geometric configuration of this inclusion on the plastic region evolution has close relationship of creep damage advancement in experiments

Multiscale Modeling of PEEK Using Reactive Molecular Dynamics Modeling and Micromechanics

Science.gov (United States)

Pisani, William A.; Radue, Matthew; Chinkanjanarot, Sorayot; Bednarcyk, Brett A.; Pineda, Evan J.; King, Julia A.; Odegard, Gregory M.

2018-01-01

Polyether ether ketone (PEEK) is a high-performance, semi-crystalline thermoplastic that is used in a wide range of engineering applications, including some structural components of aircraft. The design of new PEEK-based materials requires a precise understanding of the multiscale structure and behavior of semi-crystalline PEEK. Molecular Dynamics (MD) modeling can efficiently predict bulk-level properties of single phase polymers, and micromechanics can be used to homogenize those phases based on the overall polymer microstructure. In this study, MD modeling was used to predict the mechanical properties of the amorphous and crystalline phases of PEEK. The hierarchical microstructure of PEEK, which combines the aforementioned phases, was modeled using a multiscale modeling approach facilitated by NASA's MSGMC. The bulk mechanical properties of semi-crystalline PEEK predicted using MD modeling and MSGMC agree well with vendor data, thus validating the multiscale modeling approach.

High-Q micromechanical resonators for mass sensing in dissipative media

International Nuclear Information System (INIS)

Tappura, Kirsi; Pekko, Panu; Seppä, Heikki

2011-01-01

Single crystal silicon-based micromechanical resonators are developed for mass sensing in dissipative media. The design aspects and preliminary characterization of the resonators are presented. For the suggested designs, quality factors of about 20 000 are typically measured in air at atmospheric pressure and 1000–2000 in contact with liquid. The performance is based on a wine-glass-type lateral bulk acoustic mode excited in a rectangular resonator plate. The mode essentially eliminates the radiation of acoustic energy into the sample media leaving viscous drag as the dominant fluid-based dissipation mechanism in the system. For a mass loading distributed over the central areas of the resonator a sensitivity of 27 ppm ng −1 is measured exhibiting good agreement with the results of the finite element method-based simulations. It is also shown that the mass sensitivity can be somewhat enhanced, not only by the proper distribution of the loaded mass, but also by introducing shallow barrier structures on the resonator

Mechanical properties of Composite Engineering Structures by Multivolume Micromechanical Modelling

Directory of Open Access Journals (Sweden)

B. Novotný

2000-01-01

Full Text Available Engineering structures often consist of elements having the character of a periodically repeated composite structure. A multivolume micromechanical model based on a representative cell division into r1 × r2 × r3 subcells with different elastic material properties has been used in this paper to derive macromechanical characteristics of the composite construction response to applied load and temperature changes. The multivolume method is based on ensuring the equilibrium of the considered volume on an average basis. In the same (average way, the continuity conditions of displacements and tractions at the interfaces between subcells and between neighboring representative elements are imposed, resulting in a homogenization procedure that eliminates the discrete nature of the composite model. The details of the method are shown for the case of a concrete block pavement. A parametric study is presented illustrating the influence of joint thickness, joint filling material properties and the quality of bonding between block and filler elements.

Mechanical Performance of Natural / Natural Fiber Reinforced Hybrid Composite Materials Using Finite Element Method Based Micromechanics and Experiments

OpenAIRE

Rahman, Muhammad Ziaur

2017-01-01

A micromechanical analysis of the representative volume element (RVE) of a unidirectional flax/jute fiber reinforced epoxy composite is performed using finite element analysis (FEA). To do so, first effective mechanical properties of flax fiber and jute fiber are evaluated numerically and then used in evaluating the effective properties of ax/jute/epoxy hybrid composite. Mechanics of Structure Genome (MSG), a new homogenization tool developed in Purdue University, is used to calculate the hom...

Micro-mechanical investigation of the effect of fine content on mechanical behavior of gap graded granular materials using DEM

Directory of Open Access Journals (Sweden)

Taha Habib

2017-01-01

Full Text Available In this paper, we present a micro-mechanical study of the effect of fine content on the behavior of gap graded granular samples by using numerical simulations performed with the Discrete Element Method. Different samples with fine content varied from 0% to 30% are simulated. The role of fine content in reinforcing the granular skeleton and in supporting the external deviatoric stress is then brought into the light.

Dependency Defence and Dependency Analysis Guidance. Volume 2: Appendix 3-8. How to analyse and protect against dependent failures. Summary report of the Nordic Working Group on Common Cause Failure Analysis

International Nuclear Information System (INIS)

Johanson, Gunnar; Hellstroem, Per; Makamo, Tuomas; Bento, Jean-Pierre; Knochenhauer, Michael; Poern, Kurt

2003-10-01

best possible and realistic CCF parameter estimates, if possible, plant specific. This second volume contains the following appendices: How to protect against dependent failures, How to model and analyse dependent failures, Data for dependent failures, Literature survey, Terms and definitions, Nordic Working group on CCF Studies - Project Programme

Micromechanical performance of interfacial transition zone in fiber-reinforced cement matrix

Science.gov (United States)

Zacharda, V.; Němeček, J.; Štemberk, P.

2017-09-01

The paper investigates microstructure, chemical composition and micromechanical behavior of an interfacial transition zone (ITZ) in steel fiber reinforced cement matrix. For this goal, a combination of scanning electron microscopy (SEM), nanoindentation and elastic homogenization theory are used. The investigated sample of cement paste with dispersed reinforcement consists of cement CEM I 42,5R and a steel fiber TriTreg 50 mm. The microscopy revealed smaller portion of clinkers and larger porosity in the ITZ. Nanoindentation delivered decreased elastic modulus in comparison with cement bulk (67%) and the width of ITZ (∼ 40 μm). The measured properties served as input parameters for a simple two-scale model for elastic properties of the composite. Although, no major influence of ITZ properties on the composite elastic behavior was found, the findings about the ITZ reduced properties and its size can serve as input to other microstructural fracture based models.

Microstructural heterogeneity directs micromechanics and mechanobiology in native and engineered fibrocartilage

Science.gov (United States)

Han, Woojin M.; Heo, Su-Jin; Driscoll, Tristan P.; Delucca, John F.; McLeod, Claire M.; Smith, Lachlan J.; Duncan, Randall L.; Mauck, Robert L.; Elliott, Dawn M.

2016-04-01

Treatment strategies to address pathologies of fibrocartilaginous tissue are in part limited by an incomplete understanding of structure-function relationships in these load-bearing tissues. There is therefore a pressing need to develop micro-engineered tissue platforms that can recreate the highly inhomogeneous tissue microstructures that are known to influence mechanotransductive processes in normal and diseased tissue. Here, we report the quantification of proteoglycan-rich microdomains in developing, ageing and diseased fibrocartilaginous tissues, and the impact of these microdomains on endogenous cell responses to physiologic deformation within a native-tissue context. We also developed a method to generate heterogeneous tissue-engineered constructs (hetTECs) with non-fibrous proteoglycan-rich microdomains engineered into the fibrous structure, and show that these hetTECs match the microstructural, micromechanical and mechanobiological benchmarks of native tissue. Our tissue-engineered platform should facilitate the study of the mechanobiology of developing, homeostatic, degenerating and regenerating fibrous tissues.

Identifying design parameters controlling damage behaviors of continuous fiber-reinforced thermoplastic composites using micromechanics as a virtual testing tool

KAUST Repository

Pulungan, Ditho Ardiansyah; Lubineau, Gilles; Yudhanto, Arief; Yaldiz, Recep; Schijve, Warden

2017-01-01

In this paper, we propose a micromechanical approach to predict damage mechanisms and their interactions in glass fibers/polypropylene thermoplastic composites. First, a representative volume element (RVE) of such materials was rigorously determined using a geometrical two-point probability function and the eigenvalue stabilization of homogenized elastic tensor obtained by Hill-Mandel kinematic homogenization. Next, the 3D finite element models of the RVE were developed accordingly. The fibers were modeled with an isotropic linear elastic material. The matrix was modeled with an isotropic linear elastic, rate-independent hyperbolic Drucker-Prager plasticity coupled with a ductile damage model that is able to show pressure dependency of the yield and damage behavior often found in a thermoplastic material. In addition, cohesive elements were inserted into the fiber-matrix interfaces to simulate debonding. The RVE faces are imposed with periodical boundary conditions to minimize the edge effect. The RVE was then subjected to transverse tensile loading in accordance with experimental tensile tests on [90]8 laminates. The model prediction was found to be in very good agreement with the experimental results in terms of the global stress-strain curves, including the linear and nonlinear portion of the response and also the failure point, making it a useful virtual testing tool for composite material design. Furthermore, the effect of tailoring the main parameters of thermoplastic composites is investigated to provide guidelines for future improvements of these materials.

Identifying design parameters controlling damage behaviors of continuous fiber-reinforced thermoplastic composites using micromechanics as a virtual testing tool

KAUST Repository

Pulungan, Ditho Ardiansyah

2017-03-31

In this paper, we propose a micromechanical approach to predict damage mechanisms and their interactions in glass fibers/polypropylene thermoplastic composites. First, a representative volume element (RVE) of such materials was rigorously determined using a geometrical two-point probability function and the eigenvalue stabilization of homogenized elastic tensor obtained by Hill-Mandel kinematic homogenization. Next, the 3D finite element models of the RVE were developed accordingly. The fibers were modeled with an isotropic linear elastic material. The matrix was modeled with an isotropic linear elastic, rate-independent hyperbolic Drucker-Prager plasticity coupled with a ductile damage model that is able to show pressure dependency of the yield and damage behavior often found in a thermoplastic material. In addition, cohesive elements were inserted into the fiber-matrix interfaces to simulate debonding. The RVE faces are imposed with periodical boundary conditions to minimize the edge effect. The RVE was then subjected to transverse tensile loading in accordance with experimental tensile tests on [90]8 laminates. The model prediction was found to be in very good agreement with the experimental results in terms of the global stress-strain curves, including the linear and nonlinear portion of the response and also the failure point, making it a useful virtual testing tool for composite material design. Furthermore, the effect of tailoring the main parameters of thermoplastic composites is investigated to provide guidelines for future improvements of these materials.

Biomarker Guided Therapy in Chronic Heart Failure

Science.gov (United States)

Bektas, Sema

2015-01-01

This review article addresses the question of whether biomarker-guided therapy is ready for clinical implementation in chronic heart failure. The most well-known biomarkers in heart failure are natriuretic peptides, namely B-type natriuretic peptide (BNP) and N-terminal pro-BNP. They are well-established in the diagnostic process of acute heart failure and prediction of disease prognosis. They may also be helpful in screening patients at risk of developing heart failure. Although studied by 11 small- to medium-scale trials resulting in several positive meta-analyses, it is less well-established whether natriuretic peptides are also helpful for guiding chronic heart failure therapy. This uncertainty is expressed by differences in European and American guideline recommendations. In addition to reviewing the evidence surrounding the use of natriuretic peptides to guide chronic heart failure therapy, this article gives an overview of the shortcomings of the trials, how the results may be interpreted and the future directions necessary to fill the current gaps in knowledge. Therapy guidance in chronic heart failure using other biomarkers has not been prospectively tested to date. Emerging biomarkers, such as galectin-3 and soluble ST2, might be useful in this regard, as suggested by several post-hoc analyses. PMID:28785440

Selected papers from the 23rd MicroMechanics and Microsystems Europe Workshop (MME 2012) (Ilmenau, Germany, September 9-12, 2012)

Science.gov (United States)

Hoffmann, Martin

2013-07-01

In September 2012, the 23rd MicroMechanics Europe Workshop (MME) took place in Ilmenau, Germany. With about 120 participants from 20 countries and 76 accepted presentations, the workshop series turned out to be a successful platform for young scientists to present their work to our scientific community. Traditionally, the interaction is an important aspect of this workshop: while short presentations introduce the posters, an extended poster session allows intensive discussion which is quite useful to the participants. The discussion very often extends into the breaks and the evening events. It is also encouraging for them that the best presentations are selected and invited to submit a full paper to this journal. Thanks to the support of IOP Publishing, this next logical step to present work to the scientific world is made possible. In this issue, you can find the best papers that have been selected by a committee during the workshop taking the written workshop contribution, the poster and the presentation into account. Again, all areas of micromechanics from new technology developments up to systems integration were presented at the workshop at different levels of completion. The selected papers present those results which are almost complete. Nevertheless, it is nice to see that in some cases topics grow over the years from 'nice ideas' to realized system concepts. And although this is the 23rd workshop, it is clear that micromechanics is a topic that is not running short of new ideas. First, I would like to thank the authors of the selected papers for each of their individual excellent contributions. My gratitude also goes to my fellow members in the programme committee (Per Ohlckers, Martin Hill and Sami Franssila) for their cooperation in the selection of invited speakers and submitted papers, as well as the anonymous Journal of Micromechanics and Microengineering (JMM) reviewers for their careful selection of the final papers presented here. Last, but not

Local relative density modulates failure and strength in vertically aligned carbon nanotubes.

Science.gov (United States)

Pathak, Siddhartha; Mohan, Nisha; Decolvenaere, Elizabeth; Needleman, Alan; Bedewy, Mostafa; Hart, A John; Greer, Julia R

2013-10-22

Micromechanical experiments, image analysis, and theoretical modeling revealed that local failure events and compressive stresses of vertically aligned carbon nanotubes (VACNTs) were uniquely linked to relative density gradients. Edge detection analysis of systematically obtained scanning electron micrographs was used to quantify a microstructural figure-of-merit related to relative local density along VACNT heights. Sequential bottom-to-top buckling and hardening in stress-strain response were observed in samples with smaller relative density at the bottom. When density gradient was insubstantial or reversed, bottom regions always buckled last, and a flat stress plateau was obtained. These findings were consistent with predictions of a 2D material model based on a viscoplastic solid with plastic non-normality and a hardening-softening-hardening plastic flow relation. The hardening slope in compression generated by the model was directly related to the stiffness gradient along the sample height, and hence to the local relative density. These results demonstrate that a microstructural figure-of-merit, the effective relative density, can be used to quantify and predict the mechanical response.

Concepts for measuring maintenance performance and methods for analysing competing failure modes

DEFF Research Database (Denmark)

Cooke, R.; Paulsen, J.L.

1997-01-01

competing failure modes. This article examines ways to assess maintenance performance without introducing statistical assumptions, then introduces a plausible statistical model for describing the interaction of preventive and corrective maintenance, and finally illustrates these with examples from...

Microstructures, Forming Limit and Failure Analyses of Inconel 718 Sheets for Fabrication of Aerospace Components

Science.gov (United States)

Sajun Prasad, K.; Panda, Sushanta Kumar; Kar, Sujoy Kumar; Sen, Mainak; Murty, S. V. S. Naryana; Sharma, Sharad Chandra

2017-04-01

Recently, aerospace industries have shown increasing interest in forming limits of Inconel 718 sheet metals, which can be utilised in designing tools and selection of process parameters for successful fabrication of components. In the present work, stress-strain response with failure strains was evaluated by uniaxial tensile tests in different orientations, and two-stage work-hardening behavior was observed. In spite of highly preferred texture, tensile properties showed minor variations in different orientations due to the random distribution of nanoprecipitates. The forming limit strains were evaluated by deforming specimens in seven different strain paths using limiting dome height (LDH) test facility. Mostly, the specimens failed without prior indication of localized necking. Thus, fracture forming limit diagram (FFLD) was evaluated, and bending correction was imposed due to the use of sub-size hemispherical punch. The failure strains of FFLD were converted into major-minor stress space ( σ-FFLD) and effective plastic strain-stress triaxiality space ( ηEPS-FFLD) as failure criteria to avoid the strain path dependence. Moreover, FE model was developed, and the LDH, strain distribution and failure location were predicted successfully using above-mentioned failure criteria with two stages of work hardening. Fractographs were correlated with the fracture behavior and formability of sheet metal.

An Experimental Investigation into Failure and Localization Phenomena in the Extension to Shear Fracture Transition in Rock

Science.gov (United States)

Choens, R. C., II; Chester, F. M.; Bauer, S. J.; Flint, G. M.

2014-12-01

Fluid-pressure assisted fracturing can produce mesh and other large, interconnected and complex networks consisting of both extension and shear fractures in various metamorphic, magmatic and tectonic systems. Presently, rock failure criteria for tensile and low-mean compressive stress conditions is poorly defined, although there is accumulating evidence that the transition from extension to shear fracture with increasing mean stress is continuous. We report on the results of experiments designed to document failure criteria, fracture mode, and localization phenomena for several rock types (sandstone, limestone, chalk and marble). Experiments were conducted in triaxial extension using a necked (dogbone) geometry to achieve mixed tension and compression stress states with local component-strain measurements in the failure region. The failure envelope for all rock types is similar, but are poorly described using Griffith or modified Griffith (Coulomb or other) failure criteria. Notably, the mode of fracture changes systematically from pure extension to shear with increase in compressive mean stress and display a continuous change in fracture orientation with respect to principal stress axes. Differential stress and inelastic strain show a systematic increase with increasing mean stress, whereas the axial stress decreases before increasing with increasing mean stress. The stress and strain data are used to analyze elastic and plastic strains leading to failure and compare the experimental results to predictions for localization using constitutive models incorporating on bifurcation theory. Although models are able to describe the stability behavior and onset of localization qualitatively, the models are unable to predict fracture type or orientation. Constitutive models using single or multiple yield surfaces are unable to predict the experimental results, reflecting the difficulty in capturing the changing micromechanisms from extension to shear failure. Sandia

Microstructural Heterogeneity in Native and Engineered Fibrocartilage Directs Micromechanics and Mechanobiology

Science.gov (United States)

Han, Woojin M; Heo, Su-Jin; Driscoll, Tristan P; Delucca, John F; McLeod, Claire M; Smith, Lachlan J; Duncan, Randall L; Mauck, Robert L; Elliott, Dawn M

2015-01-01

Treatment strategies to address pathologies of fibrocartilaginous tissue are in part limited by an incomplete understanding of structure-function relationships in these load-bearing tissues. There is therefore a pressing need to develop microengineered tissue platforms that can recreate the highly inhomogeneous tissue microstructures that are known to influence mechanotransductive processes in normal and diseased tissue. Here, we report the quantification of proteoglycan-rich microdomains in developing, aging, and diseased fibrocartilaginous tissues, and the impact of these microdomains on endogenous cell responses to physiologic deformation within a native-tissue context. We also developed a method to generate heterogeneous tissue engineered constructs (hetTECs) with microscale non-fibrous proteoglycan-rich microdomains engineered into the fibrous structure, and show that these hetTECs match the microstructural, micromechanical, and mechanobiological benchmarks of native tissue. Our tissue engineered platform should facilitate the study of the mechanobiology of developing, homeostatic, degenerating, and regenerating fibrous tissues. PMID:26726994

Metallic materials for the hydrogen energy industry and main gas pipelines: complex physical problems of aging, embrittlement, and failure

International Nuclear Information System (INIS)

Nechaev, Yu S

2008-01-01

The possibilities of effective solutions of relevant technological problems are considered based on the analysis of fundamental physical aspects, elucidation of the micromechanisms and interrelations of aging and hydrogen embrittlement of materials in the hydrogen industry and gas-main industries. The adverse effects these mechanisms and processes have on the service properties and technological lifetime of materials are analyzed. The concomitant fundamental process of formation of carbohydride-like and other nanosegregation structures at dislocations (with the segregation capacity 1 to 1.5 orders of magnitude greater than in the widely used Cottrell 'atmosphere' model) and grain boundaries is discussed, as is the way in which these structures affect technological processes (aging, hydrogen embrittlement, stress corrosion damage, and failure) and the physicomechanical properties of the metallic materials (including the technological lifetimes of pipeline steels). (reviews of topical problems)

Fuel micro-mechanics: homogenization, cracking, granular media

International Nuclear Information System (INIS)

Monerie, Yann

2010-01-01

This work summarizes about fifteen years of research in the field of micro-mechanics of materials. Emphasis is placed on the most recent work carried out in the context of nuclear safety. Micro-mechanics finds a natural place there, aiming to predict the behavior of heterogeneous materials with an evolving microstructure. The applications concerned mainly involve the nuclear fuel and its tubular cladding. The uranium dioxide fuel is modeled, according to the scales under consideration, as a porous ceramic or a granular medium. The strongly irradiated Zircaloy claddings are identified with a composite medium with a metal matrix and a gradient of properties. The analysis of these classes of material is rich in problems of a more fundamental nature. Three main themes are discussed: 1/ Homogenization, 2/ cracking, rupture and fragmentation, 3/ discrete media and fluid-grain couplings. Homogenization: The analytical scale change methods proposed aim to estimate or limit the linear and equivalent nonlinear behaviors of isotropic porous media and anisotropic composites with a metal matrix. The porous media under consideration are saturated or drained, with a compressible or incompressible matrix, and have one or two scales of spherical or ellipsoid pores, or cracks. The composites studied have a macroscopic anisotropy related to that of the matrix, and to the shape and spatial distribution of the inclusions. Thermoelastic, elastoplastic, and viscoplastic behaviors and ductile damage of these media are examined using different techniques: extensions of classic approaches, linear in particular, variational approaches and approaches using elliptical potentials with thermally activated elementary mechanisms. The models developed are validated on numerical finite element simulations, and their functional relevance is illustrated in comparison to experimental data obtained from the literature. The significant results obtained include a plasticity criterion for Gurson matrix

Broadening failure rate distributions in PRA uncertainty analyses

International Nuclear Information System (INIS)

Martz, H.F.

1984-01-01

Several recent nuclear power plant probabilistic risk assessments (PRAs) have utilized broadened Reactor Safety Study (RSS) component failure rate population variability curves to compensate for such things as expert overvaluation bias in the estimates upon which the curves are based. A simple two-components of variation empirical Bayes model is proposed for use in estimating the between-expert variability curve in the presence of such biases. Under certain conditions this curve is a population variability curve. Comparisons are made with the existing method. The popular procedure appears to be generally much more conservative than the empirical Bayes method in removing such biases. In one case the broadened curve based on the popular method is more than two orders of magnitude broader than the empirical Bayes curve. In another case it is found that the maximum justifiable degree of broadening of the RSS curve is to increase α from 5% to 12%, which is significantly less than 20% value recommended in the popular approach. 15 references, 1 figure, 5 tables

Development of a micromechanical pitch-tunable grating with reflective/transmissive dual working modes

International Nuclear Information System (INIS)

Yu, Yi-Ting; Yuan, Wei-Zheng; Li, Tai-Ping; Yan, Bin

2010-01-01

In this paper, a micromechanical pitch-tunable grating with the capability of working in both reflective and transmissive modes is developed by using the silicon-on-glass (SOG) process. At a voltage of 65 V, the grating period is measured to increase by 4.62%. A simple optical experiment is performed to demonstrate how the proposed grating works in both modes. Then, experiments to measure the change of the diffraction angle versus driving voltage in both reflective and transmissive modes are designed and carried out utilizing an area-arrayed charge-coupled device (CCD), and the results are in good agreement with the theoretical calculation. Discussions on the structural configuration and diffraction efficiency of the proposed grating are presented. The grating presented provides better flexibility in the design and development of application systems.

Fatigue behaviour of synthetic nodular cast irons

Directory of Open Access Journals (Sweden)

A. Vaško

2015-01-01

Full Text Available The paper shows the influence of charge composition on microstructure, fatigue properties and failure micromechanisms of nodular cast irons. The additive of metallurgical silicon carbide (SiC in analysed specimens increases the content of ferrite in the matrix, decreases the size of graphite and increases the average count of graphitic nodules per unit of area. Consequently, the mechanical and fatigue properties of nodular cast iron are improved. The best fatigue properties (fatigue strength were reached in the melt which was created by 60 % of steel scrap and 40 % of pig iron in the basic charge with SiC additive.

Failures and Defects in the Building Process

DEFF Research Database (Denmark)

Jørgensen, Kirsten

2009-01-01

Function failures, defects, mistakes and poor communication are major problems for the construction sector. As the empirical element in the research, a large construction site was observed from the very start to the very end and all failures and defects of a certain size were recorded and analysed...

Analysis of events with common cause failures (CCF) from the international common cause failure date exchange (ICDE); Analyse von Ereignissen mit gemeinsam verursachten Ausfaellen (GVA) aus dem internationalen GVA-Datenaustauschprojekt ICDE

Energy Technology Data Exchange (ETDEWEB)

Brueck, Benjamin; Kreuser, Albert; Simon, Julia; Stiller, Jan

2014-08-15

Common-cause-failure (CCF) events can significantly impact the availability of safety systems of nuclear power plants. In recognition of this, CCF data are systematically being collected and analyzed in several countries. A comprehensive evaluation of CCF events derived only from the operating experience in German nuclear power plants is not sufficient due to the low probability of occurrence of such events. Therefore it is necessary to make use of the operating experience of other countries using similar technology. In order to be able to use the CCF operating experience from other countries in the aim to carry on the development of the bases for evaluation of CCF GRS decisively co-initiated the setting up of an international common-cause failure working group. This working group has elaborated the project ''International Common-Cause Failure Data Exchange'' (ICDE). The project's objective is to organize a broad exchange of information concerning observed events with relevance to common-cause failures. The tasks for preparation and evaluation of information of the ICDE working group serve for confirmation and extension of the common-cause failure knowledge with regards to probabilistic safety analyses, the better understanding of causes and mechanisms of common-cause failures and the evaluation of preventive measures against the occurrence of common-cause failures. The objectives of the exchange on a long term basis are to - improve the comprehension of CCF events and their causes and their prevention, - generate qualitative insights into the root causes of CCF events which can then be used to derive and assess preventive measures against the occurrence of such events or their consequences, - establish an efficient feedback of experience gained in connection with observed common-cause failure phenomena which could be used e.g. for the development of indicators for risk based inspections, - provide quantitative information regarding the

Effects of fabrication on the mechanics, microstructure and micromechanical environment of small intestinal submucosa scaffolds for vascular tissue engineering.

Science.gov (United States)

Sánchez-Palencia, Diana M; D'Amore, Antonio; González-Mancera, Andrés; Wagner, William R; Briceño, Juan C

2014-08-22

In small intestinal submucosa scaffolds for functional tissue engineering, the impact of scaffold fabrication parameters on success rate may be related to the mechanotransductory properties of the final microstructural organization of collagen fibers. We hypothesized that two fabrication parameters, 1) preservation (P) or removal (R) of a dense collagen layer present in SIS and 2) SIS in a final dehydrated (D) or hydrated (H) state, have an effect on scaffold void area, microstructural anisotropy (fiber alignment) and mechanical anisotropy (global mechanical compliance). We further integrated our experimental measurements in a constitutive model to explore final effects on the micromechanical environment inside the scaffold volume. Our results indicated that PH scaffolds might exhibit recurrent and large force fluctuations between layers (up to 195 pN), while fluctuations in RH scaffolds might be larger (up to 256 pN) but not as recurrent. In contrast, both PD and RD groups were estimated to produce scarcer and smaller fluctuations (not larger than 50 pN). We concluded that the hydration parameter strongly affects the micromechanics of SIS and that an adequate choice of fabrication parameters, assisted by the herein developed method, might leverage the use of SIS for functional tissue engineering applications, where forces at the cellular level are of concern in the guidance of new tissue formation. Copyright © 2014 Elsevier Ltd. All rights reserved.

Simulation of micromechanical behavior of polycrystals: finite elements versus fast Fourier transforms

International Nuclear Information System (INIS)

Prakash, A; Lebensohn, R A

2009-01-01

In this work, we compare finite element and fast Fourier transform approaches for the prediction of the micromechanical behavior of polycrystals. Both approaches are full-field approaches and use the same visco-plastic single crystal constitutive law. We investigate the texture and the heterogeneity of the inter- and intragranular stress and strain fields obtained from the two models. Additionally, we also look into their computational performance. Two cases—rolling of aluminum and wire drawing of tungsten—are used to evaluate the predictions of the two models. Results from both the models are similar, when large grain distortions do not occur in the polycrystal. The finite element simulations were found to be highly computationally intensive, in comparison with the fast Fourier transform simulations. Figure 9 was corrected in this article on the 25 August 2009. The corrected electronic version is identical to the print version

Characterization of metal additive manufacturing surfaces using synchrotron X-ray CT and micromechanical modeling

Science.gov (United States)

Kantzos, C. A.; Cunningham, R. W.; Tari, V.; Rollett, A. D.

2018-05-01

Characterizing complex surface topologies is necessary to understand stress concentrations created by rough surfaces, particularly those made via laser power-bed additive manufacturing (AM). Synchrotron-based X-ray microtomography (μ XCT) of AM surfaces was shown to provide high resolution detail of surface features and near-surface porosity. Using the CT reconstructions to instantiate a micromechanical model indicated that surface notches and near-surface porosity both act as stress concentrators, while adhered powder carried little to no load. Differences in powder size distribution had no direct effect on the relevant surface features, nor on stress concentrations. Conventional measurements of surface roughness, which are highly influenced by adhered powder, are therefore unlikely to contain the information relevant to damage accumulation and crack initiation.

A microcontroller-based interface circuit for data acquisition and control of a micromechanical thermal flow sensor

International Nuclear Information System (INIS)

Asimakopoulos, P; Kaltsas, G; Nassiopoulou, A G

2005-01-01

In the present work, a special microcontroller-based data acquisition and control system was designed and fabricated, for fast and accurate flow measurements with programmable modes of operation. The system can apply predetermined power to the heater and simultaneously is able of monitoring both the thermopile signal and the heater current. An RS232 connection was also implemented for the communication with the outside world. The interface circuit was adapted to the micromechanical flow sensor for evaluation. Various sensor parameters were extracted in both laminar and turbulent flow conditions. The sensor responses with three operation modes (constant voltage, power and temperature) were also obtained

A microcontroller-based interface circuit for data acquisition and control of a micromechanical thermal flow sensor

Science.gov (United States)

Asimakopoulos, P.; Kaltsas, G.; Nassiopoulou, A. G.

2005-01-01

In the present work, a special microcontroller-based data acquisition and control system was designed and fabricated, for fast and accurate flow measurements with programmable modes of operation. The system can apply predetermined power to the heater and simultaneously is able of monitoring both the thermopile signal and the heater current. An RS232 connection was also implemented for the communication with the outside world. The interface circuit was adapted to the micromechanical flow sensor for evaluation. Various sensor parameters were extracted in both laminar and turbulent flow conditions. The sensor responses with three operation modes (constant voltage, power and temperature) were also obtained.

Micro-mechanical properties of different sites on woodpecker's skull.

Science.gov (United States)

Ni, Yikun; Wang, Lizhen; Liu, Xiaoyu; Zhang, Hongquan; Lin, Chia-Ying; Fan, Yubo

2017-11-01

The uneven distributed microstructure featured with plate-like spongy bone in woodpecker's skull has been found to further help reduce the impact during woodpecker's pecking behavior. Therefore, this work was to investigate the micro-mechanical properties and composition on different sites of Great Spotted woodpecker's (GSW) skull. Different sites were selected on forehead, tempus and occiput, which were also compared with those of Eurasian Hoopoe (EH) and Lark birds (LB). Micro structural parameters assessed from micro computed tomography (μCT) occurred significantly difference between GSW, EH and LB. The micro finite element (micro-FE) models were developed and the simulation was performed as a compression process. The maximal stresses of GSW's micro-FE models were all lower than those of EH and LB respectively and few concentrated stresses were noticed on GSW's trabecular bone. Fourier transform infrared mapping suggesting a greater organic content in the occiput of GSW's cranial bone compared with others. The nano-hardness of the GSW's occiput was decreasing from forehead to occiput. The mechanical properties, site-dependent hardness distribution and special material composition of GSW's skull bone are newly found in this study. These factors may lead to a new design of bulk material mimicking these characteristics.

Experimental determination of the micro-scale strength and stress-strain relation of an epoxy resin

DEFF Research Database (Denmark)

Zike, Sanita; Sørensen, Bent F.; Mikkelsen, Lars Pilgaard

2016-01-01

An approach is developed for determining the stress-strain law and a failure stress appropriate for micro-mechanical models of polymer materials. Double cantilever beam test specimens, made of an epoxy polymer with notches having finite root radius, were subjected to pure bending moments in an en......An approach is developed for determining the stress-strain law and a failure stress appropriate for micro-mechanical models of polymer materials. Double cantilever beam test specimens, made of an epoxy polymer with notches having finite root radius, were subjected to pure bending moments......-scale (5–6%). The hardening exponent of a power law hardening material was obtained by the use of the J-integral, estimating the strain energy density around the notch. The hardening exponent was found to be within the range of 5–6 and the corresponding micro-scale failure stress was in the range of 220...

Seismic fragility analyses

International Nuclear Information System (INIS)

Kostov, Marin

2000-01-01

In the last two decades there is increasing number of probabilistic seismic risk assessments performed. The basic ideas of the procedure for performing a Probabilistic Safety Analysis (PSA) of critical structures (NUREG/CR-2300, 1983) could be used also for normal industrial and residential buildings, dams or other structures. The general formulation of the risk assessment procedure applied in this investigation is presented in Franzini, et al., 1984. The probability of failure of a structure for an expected lifetime (for example 50 years) can be obtained from the annual frequency of failure, β E determined by the relation: β E ∫[d[β(x)]/dx]P(flx)dx. β(x) is the annual frequency of exceedance of load level x (for example, the variable x may be peak ground acceleration), P(fI x) is the conditional probability of structure failure at a given seismic load level x. The problem leads to the assessment of the seismic hazard β(x) and the fragility P(fl x). The seismic hazard curves are obtained by the probabilistic seismic hazard analysis. The fragility curves are obtained after the response of the structure is defined as probabilistic and its capacity and the associated uncertainties are assessed. Finally the fragility curves are combined with the seismic loading to estimate the frequency of failure for each critical scenario. The frequency of failure due to seismic event is presented by the scenario with the highest frequency. The tools usually applied for probabilistic safety analyses of critical structures could relatively easily be adopted to ordinary structures. The key problems are the seismic hazard definitions and the fragility analyses. The fragility could be derived either based on scaling procedures or on the base of generation. Both approaches have been presented in the paper. After the seismic risk (in terms of failure probability) is assessed there are several approaches for risk reduction. Generally the methods could be classified in two groups. The

Micromechanics approach to the magnetoelectric properties of laminate and fibrous piezoelectric/magnetostrictive composites

International Nuclear Information System (INIS)

Huang Haitao; Zhou, L.M.

2004-01-01

We use a micromechanics approach to study the magnetoelectric (ME) properties of the piezoelectric/magnetostrictive composite with a 2-2 laminate structure and a 3-1 fibrous structure. It is found that the 3-1 composite has a higher ME coefficient than the 2-2 one, if the volume ratio of piezoelectric material is the same. The reason is that the 3-1 fibrous composite makes use of the longitudinal piezoelectric response and the piezoelectric voltage constant g 33 is 2-3 times that of g 31 . Generally, a smaller volume ratio of the piezoelectric material will generate a higher ME response. The tensile stress at the piezoelectric/magnetostrictive interface of the 3-1 fibrous composite, however, could be high enough to induce plastic deformation or microcracks, which leads to a ME coefficient lower than the theoretically predicted one

Discrete Analysis of Damage and Shear Banding in Argillaceous Rocks

Science.gov (United States)

Dinç, Özge; Scholtès, Luc

2018-05-01

A discrete approach is proposed to study damage and failure processes taking place in argillaceous rocks which present a transversely isotropic behavior. More precisely, a dedicated discrete element method is utilized to provide a micromechanical description of the mechanisms involved. The purpose of the study is twofold: (1) presenting a three-dimensional discrete element model able to simulate the anisotropic macro-mechanical behavior of the Callovo-Oxfordian claystone as a particular case of argillaceous rocks; (2) studying how progressive failure develops in such material. Material anisotropy is explicitly taken into account in the numerical model through the introduction of weakness planes distributed at the interparticle scale following predefined orientation and intensity. Simulations of compression tests under plane-strain and triaxial conditions are performed to clarify the development of damage and the appearance of shear bands through micromechanical analyses. The overall mechanical behavior and shear banding patterns predicted by the numerical model are in good agreement with respect to experimental observations. Both tensile and shear microcracks emerging from the modeling also present characteristics compatible with microstructural observations. The numerical results confirm that the global failure of argillaceous rocks is well correlated with the mechanisms taking place at the local scale. Specifically, strain localization is shown to directly result from shear microcracking developing with a preferential orientation distribution related to the orientation of the shear band. In addition, localization events presenting characteristics similar to shear bands are observed from the early stages of the loading and might thus be considered as precursors of strain localization.

Low Cycle Fatigue Behaviour of DP Steels: Micromechanical Modelling vs. Validation

Directory of Open Access Journals (Sweden)

Ghazal Moeini

2017-07-01

Full Text Available This study aims to simulate the stabilised stress-strain hysteresis loop of dual phase (DP steel using micromechanical modelling. For this purpose, the investigation was conducted both experimentally and numerically. In the experimental part, the microstructure characterisation, monotonic tensile tests and low cycle fatigue tests were performed. In the numerical part, the representative volume element (RVE was employed to study the effect of the DP steel microstructure of the low cycle fatigue behavior of DP steel. A dislocation-density based model was utilised to identify the tensile behavior of ferrite and martensite. Then, by establishing a correlation between the monotonic and cyclic behavior of ferrite and martensite phases, the cyclic deformation properties of single phases were estimated. Accordingly, Chaboche kinematic hardening parameters were identified from the predicted cyclic curve of individual phases in DP steel. Finally, the predicted hysteresis loop from low cycle fatigue modelling was in very good agreement with the experimental one. The stabilised hysteresis loop of DP steel can be successfully predicted using the developed approach.

Investigation of Mechanical Properties of Unidirectional Steel Fiber/Polyester Composites: Experiments and Micromechanical Predictions

DEFF Research Database (Denmark)

Raghavalu Thirumalai, Durai Prabhakaran; Løgstrup Andersen, Tom; Bech, Jakob Ilsted

2016-01-01

the role of material and process parameters on material properties. Two types of SFRP were studied: polyester resin reinforced by both steel fabric containing unidirectional fibers and steel fibers wound on a metal frame with 0° orientations. The effects of the fiber volume fraction and the role of polymer......The article introduces steel fiber reinforced polymer composites, which is considered new for composite product developments. These composites consist of steel fibers or filaments of 0.21 mm diameter embedded in a polyester resin. The goal of this investigation is to characterize the mechanical...... performance of steel fiber reinforced polyester composites at room temperature. The mechanical properties of unidirectional steel fiber reinforced polyester composites (SFRP) are evaluated experimentally and compared with the predicted values by micro-mechanical models. These predictions help to understand...

Fracture mechanisms and fracture control in composite structures

Science.gov (United States)

Kim, Wone-Chul

Four basic failure modes--delamination, delamination buckling of composite sandwich panels, first-ply failure in cross-ply laminates, and compression failure--are analyzed using linear elastic fracture mechanics (LEFM) and the J-integral method. Structural failures, including those at the micromechanical level, are investigated with the aid of the models developed, and the critical strains for crack propagation for each mode are obtained. In the structural fracture analyses area, the fracture control schemes for delamination in a composite rib stiffener and delamination buckling in composite sandwich panels subjected to in-plane compression are determined. The critical fracture strains were predicted with the aid of LEFM for delamination and the J-integral method for delamination buckling. The use of toughened matrix systems has been recommended for improved damage tolerant design for delamination crack propagation. An experimental study was conducted to determine the onset of delamination buckling in composite sandwich panel containing flaws. The critical fracture loads computed using the proposed theoretical model and a numerical computational scheme closely followed the experimental measurements made on sandwich panel specimens of graphite/epoxy faceskins and aluminum honeycomb core with varying faceskin thicknesses and core sizes. Micromechanical models of fracture in composites are explored to predict transverse cracking of cross-ply laminates and compression fracture of unidirectional composites. A modified shear lag model which takes into account the important role of interlaminar shear zones between the 0 degree and 90 degree piles in cross-ply laminate is proposed and criteria for transverse cracking have been developed. For compressive failure of unidirectional composites, pre-existing defects play an important role. Using anisotropic elasticity, the stress state around a defect under a remotely applied compressive load is obtained. The experimentally

Integrated failure probability estimation based on structural integrity analysis and failure data: Natural gas pipeline case

International Nuclear Information System (INIS)

Dundulis, Gintautas; Žutautaitė, Inga; Janulionis, Remigijus; Ušpuras, Eugenijus; Rimkevičius, Sigitas; Eid, Mohamed

2016-01-01

In this paper, the authors present an approach as an overall framework for the estimation of the failure probability of pipelines based on: the results of the deterministic-probabilistic structural integrity analysis (taking into account loads, material properties, geometry, boundary conditions, crack size, and defected zone thickness), the corrosion rate, the number of defects and failure data (involved into the model via application of Bayesian method). The proposed approach is applied to estimate the failure probability of a selected part of the Lithuanian natural gas transmission network. The presented approach for the estimation of integrated failure probability is a combination of several different analyses allowing us to obtain: the critical crack's length and depth, the failure probability of the defected zone thickness, dependency of the failure probability on the age of the natural gas transmission pipeline. A model's uncertainty analysis and uncertainty propagation analysis are performed, as well. - Highlights: • Degradation mechanisms of natural gas transmission pipelines. • Fracture mechanic analysis of the pipe with crack. • Stress evaluation of the pipe with critical crack. • Deterministic-probabilistic structural integrity analysis of gas pipeline. • Integrated estimation of pipeline failure probability by Bayesian method.

Micromechanical Aspects of Transgranular and Intergranular Failure Competition

Czech Academy of Sciences Publication Activity Database

Dlouhý, Ivo; Tarafder, M.; Hadraba, Hynek

2011-01-01

Roč. 465, - (2011), s. 399-402 ISSN 1013-9826 R&D Projects: GA ČR(CZ) GAP107/10/0361 Institutional research plan: CEZ:AV0Z20410507 Keywords : intergranular fracture * cleavage * fracture toughness Subject RIV: JL - Materials Fatigue, Friction Mechanics

Analysis of failure and maintenance experiences of motor operated valves in a Finnish nuclear power plant

International Nuclear Information System (INIS)

Simola, K.; Laakso, K.

1992-01-01

Operating experiences from 1981 up to 1989 of totally 104 motor operated closing valves (MOV) in different safety systems at TVO I and II nuclear power units were analysed in a systematic way. The qualitative methods used were failure mode and effects analysis (FMEA) and maintenance effects and criticality analysis (MECA). The failure descriptions were obtained from power plant's computerized failure reporting system. The reported 181 failure events were reanalysed and sorted according to specific classifications developed for the MOV function. Filled FMEA and MECA sheets on individual valves were stored in a microcomputer data base for further analyses. Analyses were performed for the failed mechanical and electrical valve parts, ways of detection of failure modes, failure effects, and repair and unavailability times

A quantitative method for Failure Mode and Effects Analysis

NARCIS (Netherlands)

Braaksma, Anne Johannes Jan; Meesters, A.J.; Klingenberg, W.; Hicks, C.

2012-01-01

Failure Mode and Effects Analysis (FMEA) is commonly used for designing maintenance routines by analysing potential failures, predicting their effect and facilitating preventive action. It is used to make decisions on operational and capital expenditure. The literature has reported that despite its

System reliability analysis using dominant failure modes identified by selective searching technique

International Nuclear Information System (INIS)

Kim, Dong-Seok; Ok, Seung-Yong; Song, Junho; Koh, Hyun-Moo

2013-01-01

The failure of a redundant structural system is often described by innumerable system failure modes such as combinations or sequences of local failures. An efficient approach is proposed to identify dominant failure modes in the space of random variables, and then perform system reliability analysis to compute the system failure probability. To identify dominant failure modes in the decreasing order of their contributions to the system failure probability, a new simulation-based selective searching technique is developed using a genetic algorithm. The system failure probability is computed by a multi-scale matrix-based system reliability (MSR) method. Lower-scale MSR analyses evaluate the probabilities of the identified failure modes and their statistical dependence. A higher-scale MSR analysis evaluates the system failure probability based on the results of the lower-scale analyses. Three illustrative examples demonstrate the efficiency and accuracy of the approach through comparison with existing methods and Monte Carlo simulations. The results show that the proposed method skillfully identifies the dominant failure modes, including those neglected by existing approaches. The multi-scale MSR method accurately evaluates the system failure probability with statistical dependence fully considered. The decoupling between the failure mode identification and the system reliability evaluation allows for effective applications to larger structural systems

Micro-mechanical analysis and modelling of the behavior and brittle fracture of a french 16MND5 steel: role of microstructural heterogeneities; Analyse et modelisation micromecanique du comportement et de la rupture fragile de l'acier 16MND5: prise en compte des heterogeneites microstructurales

Energy Technology Data Exchange (ETDEWEB)

Mathieu, J.Ph

2006-10-15

Reactor Pressure Vessel is the second containment barrier between nuclear fuel and the environment. Electricite de France's reactors are made with french 16MND5 low-alloyed steel (equ. ASTM A508 Cl.3). Various experimental techniques (scanning electron microscopy, X-ray diffraction...) are set up in order to characterize mechanical heterogeneities inside material microstructure during tensile testing at different low temperatures [-150 C;-60 C]. Heterogeneities can be seen as the effect of both 'polycrystalline' and 'composite' microstructural features. Interphase (until 150 MPa in average between ferritic and bainitic macroscopic stress state) and intra-phase (until 100 MPa in average between ferritic orientations) stress variations are highlighted. Modelling involves micro-mechanical description of plastic glide, mean fields models and realistic three-dimensional aggregates, all put together inside a multi-scale approach. Calibration is done on macroscopic stress-strain curves at different low temperatures, and modelling reproduces experimental stress heterogeneities. This modelling allows to apply a local micro-mechanical fracture criterion for crystallographic cleavage. Deterministic computations of time to fracture for different carbides random selection provide a way to express probability of fracture for the elementary volume. Results are in good agreement with hypothesis made by local approach to fracture. Hence, the main difference is that no dependence to loading nor microstructure features is supposed for probability of fracture on the representative volume: this dependence is naturally introduced by modelling. (author)

Tritium Waste Treatment System component failure data analysis from June 18, 1984--December 31, 1989

International Nuclear Information System (INIS)

Cadwallader, L.C.; Stolpe Gavett, M.A.

1990-09-01

This document gives the failure rates for the major tritium-bearing components in the Tritium Waste Treatment System at the Tritium Systems Test Assembly, which is a fusion research and technology facility at the Los Alamos National Laboratory. The failure reports, component populations, and operating demands/hours are given in this report, and sample calculations for binomial demand failure rates and poisson hourly failure rates are given in the appendices. The failure rates for tritium-bearing components were on the order of the screening failure rate values suggested for fusion reliability and risk analyses. More effort should be directed toward collecting and analyzing fusion component failure data, since accurate failure rates are necessary to refine reliability and risk analyses. 15 refs., 4 figs., 4 tabs

Experimental approach and micro-mechanical modeling of the creep behavior of irradiated zirconium alloys

International Nuclear Information System (INIS)

Ribis, J.

2007-12-01

The fuel rod cladding, strongly affected by microstructural changes due to irradiation such as high density of dislocation loops, is strained by the end-of-life fuel rod internal pressure and the potential release of fission gases and helium during dry storage. Within the temperature range that is expected during dry interim storage, cladding undergoes long term creep under over-pressure. So, in order to have a predictive approach of the behavior of zirconium alloys cladding in dry storage conditions it is essential to take into account: initial dislocation loops, thermal annealing of loops and creep straining due to over pressure. Specific experiments and modelling for irradiated samples have been developed to improve our knowledge in that field. A Zr-1%Nb-O alloy was studied using fine microstructural investigations and mechanical testing. The observations conducted by transmission electron microscopy show that the high density of loops disappears during a heat treatment. The loop size becomes higher and higher while their density falls. The microhardness tests reveal that the fall of loop density leads to the softening of the irradiated material. During a creep test, both temperature and applied stress are responsible of the disappearance of loops. The loops could be swept by the activation of the basal slip system while the prism slip system is inhibited. Once deprived of loops, the creep properties of the irradiated materials are closed to the non irradiated state, a result whose consequence is a sudden acceleration of the creep rate. Finally, a micro-mechanical modeling based on microscopic deformation mechanisms taking into account experimental dislocation loop analyses and creep test, was used for a predictive approach by constructing a deformation mechanism map of the creep behavior of the irradiated material. (author)

Micromechanical combined stress analysis: MICSTRAN, a user manual

Science.gov (United States)

Naik, R. A.

1992-01-01

Composite materials are currently being used in aerospace and other applications. The ability to tailor the composite properties by the appropriate selection of its constituents, the fiber and matrix, is a major advantage of composite materials. The Micromechanical Combined Stress Analysis (MICSTRAN) code provides the materials engineer with a user-friendly personal computer (PC) based tool to calculate overall composite properties given the constituent fiber and matrix properties. To assess the ability of the composite to carry structural loads, the materials engineer also needs to calculate the internal stresses in the composite material. MICSTRAN is a simple tool to calculate such internal stresses with a composite ply under combined thermomechanical loading. It assumes that the fibers have a circular cross-section and are arranged either in a repeating square or diamond array pattern within a ply. It uses a classical elasticity solution technique that has been demonstrated to calculate accurate stress results. Input to the program consists of transversely isotropic fiber properties and isotropic matrix properties such as moduli, Poisson's ratios, coefficients of thermal expansion, and volume fraction. Output consists of overall thermoelastic constants and stresses. Stresses can be computed under the combined action of thermal, transverse, longitudinal, transverse shear, and longitudinal shear loadings. Stress output can be requested along the fiber-matrix interface, the model boundaries, circular arcs, or at user-specified points located anywhere in the model. The MICSTRAN program is Windows compatible and takes advantage of the Microsoft Windows graphical user interface which facilitates multitasking and extends memory access far beyond the limits imposed by the DOS operating system.

Preparation of polystyrene brush film by radical chain-transfer polymerization and micromechanical properties

Energy Technology Data Exchange (ETDEWEB)

Zhao Jing [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Graduate School of Chinese Academy of Sciences, Beijing 100039 (China); Chen Miao [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)], E-mail: miaochen99@yahoo.com; An Yanqing [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Graduate School of Chinese Academy of Sciences, Beijing 100039 (China); Liu Jianxi [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Yan Fengyuan [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)], E-mail: fyyan@lzb.ac.cn

2008-12-30

A radical chain-transfer polymerization technique has been applied to graft-polymerize brushes of polystyrene (PSt) on single-crystal silicon substrates. 3-Mercapto-propyltrimethoxysilane (MPTMS), as a chain-transfer agent for grafting, was immobilized on the silicon surface by a self-assembling process. The structure and morphology of the graft-functionalized silicon surfaces were characterized by the means of contact-angle measurement, ellipsometric thickness measurement, Fourier transformation infrared (FTIR) spectroscopy, and atomic force microscopy (AFM). The nanotribological and micromechanical properties of the as-prepared polymer brush films were investigated by frictional force microscopy (FFM), force-volume analysis and scratch test. The results indicate that the friction properties of the grafted polymer films can be improved significantly by the treatment of toluene, and the chemically bonded polystyrene film exhibits superior scratch resistance behavior compared with the spin-coated polystyrene film. The resultant polystyrene brush film is expected to develop as a potential lubrication coating for microelectromechanical systems (MEMS)

Testing and Micromechanical Modelling of Rockfill Materials Considering the Effect of Stress Path

Directory of Open Access Journals (Sweden)

Wang Feng

2016-01-01

Full Text Available We have extended the micromechanics-based analytical (M-A model to make it capable of simulating Nuozhadu rockfill material (NRFM under different stress paths. Two types of drained triaxial tests on NRFM were conducted, namely, the stress paths of constant stress ratio (CSR and the complex stress paths with transitional features. The model was improved by considering the interparticle parameter variation with the unloading-reloading cycles and the effect of the stress transition path. The evolution of local dilatancy at interparticle planes due to an externally applied load is also discussed. Compared with Duncan-Chang’s E-u and E-B models, the improved model could not only better describe the deformation properties of NRFM under the stress path loading, but also present the volumetric strain changing from dilatancy to contractancy with increasing transitional confining pressures. All simulations have demonstrated that the proposed M-A model is capable of modelling the mechanical behaviour of NRFM in the dam.

Prediction of Elastic Constants of the Fuzzy Fibre Reinforced Polymer Using Computational Micromechanics

Science.gov (United States)

Pawlik, Marzena; Lu, Yiling

2018-05-01

Computational micromechanics is a useful tool to predict properties of carbon fibre reinforced polymers. In this paper, a representative volume element (RVE) is used to investigate a fuzzy fibre reinforced polymer. The fuzzy fibre results from the introduction of nanofillers in the fibre surface. The composite being studied contains three phases, namely: the T650 carbon fibre, the carbon nanotubes (CNTs) reinforced interphase and the epoxy resin EPIKOTE 862. CNTs are radially grown on the surface of the carbon fibre, and thus resultant interphase composed of nanotubes and matrix is transversely isotropic. Transversely isotropic properties of the interphase are numerically implemented in the ANSYS FEM software using element orientation command. Obtained numerical predictions are compared with the available analytical models. It is found that the CNTs interphase significantly increased the transverse mechanical properties of the fuzzy fibre reinforced polymer. This extent of enhancement changes monotonically with the carbon fibre volume fraction. This RVE model enables to investigate different orientation of CNTs in the fuzzy fibre model.

AC power flow importance measures considering multi-element failures

International Nuclear Information System (INIS)

Li, Jian; Dueñas-Osorio, Leonardo; Chen, Changkun; Shi, Congling

2017-01-01

Quantifying the criticality of individual components of power systems is essential for overall reliability and management. This paper proposes an AC-based power flow element importance measure, while considering multi-element failures. The measure relies on a proposed AC-based cascading failure model, which captures branch overflow, bus load shedding, and branch failures, via AC power flow and optimal power flow analyses. Taking the IEEE 30, 57 and 118-bus power systems as case studies, we find that N-3 analyses are sufficient to measure the importance of a bus or branch. It is observed that for a substation bus, its importance is statistically proportional to its power demand, but this trend is not observed for power plant buses. While comparing with other reliability, functionality, and topology-based importance measures popular today, we find that a DC power flow model, although better correlated with the benchmark AC model as a whole, still fails to locate some critical elements. This is due to the focus of DC-based models on real power that ignores reactive power. The proposed importance measure is aimed to inform decision makers about key components in complex systems, while improving cascading failure prevention, system backup setting, and overall resilience. - Highlights: • We propose a novel importance measure based on joint failures and AC power flow. • A cascading failure model considers both AC power flow and optimal power flow. • We find that N-3 analyses are sufficient to measure the importance of an element. • Power demand impacts the importance of substations but less so that of generators. • DC models fail to identify some key elements, despite correlating with AC models.

Analyses of transient plant response under emergency situations

Energy Technology Data Exchange (ETDEWEB)

Koyama, Kazuya [Advanced Reactor Technology, Co. Ltd., Engineering Department, Tokyo (Japan); Shimakawa, Yoshio; Hishida, Masahiko [Mitsubishi Heavy Industry, Ltd., Reactor Core Engineering and Safety Engineering Department, Tokyo (Japan)

1999-03-01

In order to support development of the dynamic reliability analysis program DYANA, analyses were made on the event sequences anticipated under emergency situations using the plant dynamics simulation computer code Super-COPD. The analytical models were developed for Super-COPD such as the guard vessel, the maintenance cooling system, the sodium overflow and makeup system, etc. in order to apply the code to the simulation of the emergency situations. The input data were prepared for the analyses. About 70 sequences were analyzed, which are categorized into the following events: (1) PLOHS (Protected Loss of Heat Sink), (2) LORL (Loss of Reactor Level)-J: failure of sodium makeup by the primary sodium overflow and makeup system, (3) LORL-G : failure of primary coolant pump trip, (4) LORL-I: failure of the argon cover gas isolation, and (5) heat removal only using the ventilation system of the primary cooling system rooms. The results were integrated into an input file for preparing the functions for the neural network simulation. (author)

Low-frequency sound affects active micromechanics in the human inner ear

Science.gov (United States)

Kugler, Kathrin; Wiegrebe, Lutz; Grothe, Benedikt; Kössl, Manfred; Gürkov, Robert; Krause, Eike; Drexl, Markus

2014-01-01

Noise-induced hearing loss is one of the most common auditory pathologies, resulting from overstimulation of the human cochlea, an exquisitely sensitive micromechanical device. At very low frequencies (less than 250 Hz), however, the sensitivity of human hearing, and therefore the perceived loudness is poor. The perceived loudness is mediated by the inner hair cells of the cochlea which are driven very inadequately at low frequencies. To assess the impact of low-frequency (LF) sound, we exploited a by-product of the active amplification of sound outer hair cells (OHCs) perform, so-called spontaneous otoacoustic emissions. These are faint sounds produced by the inner ear that can be used to detect changes of cochlear physiology. We show that a short exposure to perceptually unobtrusive, LF sounds significantly affects OHCs: a 90 s, 80 dB(A) LF sound induced slow, concordant and positively correlated frequency and level oscillations of spontaneous otoacoustic emissions that lasted for about 2 min after LF sound offset. LF sounds, contrary to their unobtrusive perception, strongly stimulate the human cochlea and affect amplification processes in the most sensitive and important frequency range of human hearing. PMID:26064536

Wear Micro-Mechanisms of Composite WC-Co/Cr - NiCrFeBSiC Coatings. Part II: Cavitation Erosion

Directory of Open Access Journals (Sweden)

D. Kekes

2014-12-01

Full Text Available Composite coatings with five different proportions of WC-Co/Cr and NiCrFeBSiC components were deposited on stainless steel by HVOF spraying. Cavitation erosion tests were performed and the material removal micro-mechanisms were identified by SEM of both the eroded areas and the specimens’ cross-sections. Waves’ propagation and deflection at the weak interfaces within the coatings resulted in local tensile stresses perpendicular to the interface direction that eventually led to material removal. Such weak interfaces are the boundaries of the carbide particles with the metal binder within the same splat, those between splats along the same layer and those between successively deposited layers.

Lower head failure analysis

International Nuclear Information System (INIS)

Rempe, J.L.; Thinnes, G.L.; Allison, C.M.; Cronenberg, A.W.

1991-01-01

The US Nuclear Regulatory Commission is sponsoring a lower vessel head research program to investigate plausible modes of reactor vessel failure in order to determine (a) which modes have the greatest likelihood of occurrence during a severe accident and (b) the range of core debris and accident conditions that lead to these failures. This paper presents the methodology and preliminary results of an investigation of reactor designs and thermodynamic conditions using analytic closed-form approximations to assess the important governing parameters in non-dimensional form. Preliminary results illustrate the importance of vessel and tube geometrical parameters, material properties, and external boundary conditions on predicting vessel failure. Thermal analyses indicate that steady-state temperature distributions will occur in the vessel within several hours, although the exact time is dependent upon vessel thickness. In-vessel tube failure is governed by the tube-to-debris mass ratio within the lower head, where most penetrations are predicted to fail if surrounded by molten debris. Melt penetration distance is dependent upon the effective flow diameter of the tube. Molten debris is predicted to penetrate through tubes with a larger effective flow diameter, such as a boiling water reactor (BWR) drain nozzle. Ex-vessel tube failure for depressurized reactor vessels is predicted to be more likely for a BWR drain nozzle penetration because of its larger effective diameter. At high pressures (between ∼0.1 MPa and ∼12 MPa) ex-vessel tube rupture becomes a dominant failure mechanism, although tube ejection dominates control rod guide tube failure at lower temperatures. However, tube ejection and tube rupture predictions are sensitive to the vessel and tube radial gap size and material coefficients of thermal expansion

Micro-mechanical analysis and modelling of the behavior and brittle fracture of a french 16MND5 steel: role of microstructural heterogeneities

International Nuclear Information System (INIS)

Mathieu, J.Ph.

2006-10-01

Reactor Pressure Vessel is the second containment barrier between nuclear fuel and the environment. Electricite de France's reactors are made with french 16MND5 low-alloyed steel (equ. ASTM A508 Cl.3). Various experimental techniques (scanning electron microscopy, X-ray diffraction...) are set up in order to characterize mechanical heterogeneities inside material microstructure during tensile testing at different low temperatures [-150 C;-60 C]. Heterogeneities can be seen as the effect of both 'polycrystalline' and 'composite' microstructural features. Interphase (until 150 MPa in average between ferritic and bainitic macroscopic stress state) and intra-phase (until 100 MPa in average between ferritic orientations) stress variations are highlighted. Modelling involves micro-mechanical description of plastic glide, mean fields models and realistic three-dimensional aggregates, all put together inside a multi-scale approach. Calibration is done on macroscopic stress-strain curves at different low temperatures, and modelling reproduces experimental stress heterogeneities. This modelling allows to apply a local micro-mechanical fracture criterion for crystallographic cleavage. Deterministic computations of time to fracture for different carbides random selection provide a way to express probability of fracture for the elementary volume. Results are in good agreement with hypothesis made by local approach to fracture. Hence, the main difference is that no dependence to loading nor microstructure features is supposed for probability of fracture on the representative volume: this dependence is naturally introduced by modelling. (author)

Probabilistic analysis of ''common mode failures''

International Nuclear Information System (INIS)

Easterling, R.G.

1978-01-01

Common mode failure is a topic of considerable interest in reliability and safety analyses of nuclear reactors. Common mode failures are often discussed in terms of examples: two systems fail simultaneously due to an external event such as an earthquake; two components in redundant channels fail because of a common manufacturing defect; two systems fail because a component common to both fails; the failure of one system increases the stress on other systems and they fail. The common thread running through these is a dependence of some sort--statistical or physical--among multiple failure events. However, the nature of the dependence is not the same in all these examples. An attempt is made to model situations, such as the above examples, which have been termed ''common mode failures.'' In doing so, it is found that standard probability concepts and terms, such as statistically dependent and independent events, and conditional and unconditional probabilities, suffice. Thus, it is proposed that the term ''common mode failures'' be dropped, at least from technical discussions of these problems. A corollary is that the complementary term, ''random failures,'' should also be dropped. The mathematical model presented may not cover all situations which have been termed ''common mode failures,'' but provides insight into the difficulty of obtaining estimates of the probabilities of these events

Bottom head failure program plan

International Nuclear Information System (INIS)

Meyer, R.O.

1989-01-01

Earlier this year the NRC staff presented a Revised Severe Accident Research Program Plan (SECY-89-123) to the Commission and initiated work on that plan. Two of the near-term issues in that plan involve failure of the bottom head of the reactor pressure vessel. These two issues are (1) depressurization and DCH and (2) BWR Mark I Containment Shell Meltthrough. ORNL has developed models for several competing failure mechanisms for BWRs. INEL has performed analytical and experimental work directly related to bottom head failure in connection with several programs. SNL has conducted a number of analyses and experimental activities to examine the failure of LWR vessels. In addition to the government-sponsored work mentioned above, EPRI and FAI performed studies on vessel failure for the Industry Degraded Core Rulemaking Program (IDCOR). EPRI examined the failure of a PWR vessel bottom head without penetrations, as found in some Combustion Engineering reactors. To give more attention to this subject as called for by the revised Severe Accident Research Plan, two things are being done. First, work previously done is being reviewed carefully to develop an overall picture and to determine the reliability of assumptions used in those studies. Second, new work is being planned for FY90 to try to complete a reasonable understanding of the failure process. The review and planning are being done in close cooperation with the ACRS. Results of this exercise will be presented in this paper

Concepts for measuring maintenance performance and methods for analysing competing failure modes

International Nuclear Information System (INIS)

Cooke, Roger; Paulsen, Jette

1997-01-01

Measurement of maintenance performance is done on the basis of component history data in which service sojourns are distinguished according to whether they terminate in corrective or preventive maintenance. From the viewpoint of data analysis, corrective and preventive maintenance constitute competing failure nudes. This article examines ways to assess maintenance performance without introducing statistical assumptions, then introduces a plausible statistical model for describing the interaction of preventive and corrective maintenance, and finally illustrates these with examples from the Nordic TUD data system

Modelling software failures of digital I and C in probabilistic safety analyses based on the TELEPERM registered XS operating experience

International Nuclear Information System (INIS)

Jockenhoevel-Barttfeld, Mariana; Taurines Andre; Baeckstroem, Ola; Holmberg, Jan-Erik; Porthin, Markus; Tyrvaeinen, Tero

2015-01-01

Digital instrumentation and control (I and C) systems appear as upgrades in existing nuclear power plants (NPPs) and in new plant designs. In order to assess the impact of digital system failures, quantifiable reliability models are needed along with data for digital systems that are compatible with existing probabilistic safety assessments (PSA). The paper focuses on the modelling of software failures of digital I and C systems in probabilistic assessments. An analysis of software faults, failures and effects is presented to derive relevant failure modes of system and application software for the PSA. The estimations of software failure probabilities are based on an analysis of the operating experience of TELEPERM registered XS (TXS). For the assessment of application software failures the analysis combines the use of the TXS operating experience at an application function level combined with conservative engineering judgments. Failure probabilities to actuate on demand and of spurious actuation of typical reactor protection application are estimated. Moreover, the paper gives guidelines for the modelling of software failures in the PSA. The strategy presented in this paper is generic and can be applied to different software platforms and their applications.

10 CFR 61.13 - Technical analyses.

Science.gov (United States)

2010-01-01

... air, soil, groundwater, surface water, plant uptake, and exhumation by burrowing animals. The analyses... processes such as erosion, mass wasting, slope failure, settlement of wastes and backfill, infiltration through covers over disposal areas and adjacent soils, and surface drainage of the disposal site. The...

Diuretics for heart failure.

Science.gov (United States)

Faris, Rajaa F; Flather, Marcus; Purcell, Henry; Poole-Wilson, Philip A; Coats, Andrew J S

2012-02-15

Chronic heart failure is a major cause of morbidity and mortality worldwide. Diuretics are regarded as the first-line treatment for patients with congestive heart failure since they provide symptomatic relief. The effects of diuretics on disease progression and survival remain unclear. To assess the harms and benefits of diuretics for chronic heart failure Updated searches were run in the Cochrane Central Register of Controlled Trials in The Cochrane Library (CENTRAL Issue 1 of 4, 2011), MEDLINE (1966 to 22 February 2011), EMBASE (1980 to 2011 Week 07) and HERDIN database (1990 to February 2011). We hand searched pertinent journals and reference lists of papers were inspected. We also contacted manufacturers and researchers in the field. No language restrictions were applied. Double-blinded randomised controlled trials of diuretic therapy comparing one diuretic with placebo, or one diuretic with another active agent (e.g. ACE inhibitors, digoxin) in patients with chronic heart failure. Two authors independently abstracted the data and assessed the eligibility and methodological quality of each trial. Extracted data were analysed by determining the odds ratio for dichotomous data, and difference in means for continuous data, of the treated group compared with controls. The likelihood of heterogeneity of the study population was assessed by the Chi-square test. If there was no evidence of statistical heterogeneity and pooling of results was clinically appropriate, a combined estimate was obtained using the fixed-effects model. This update has not identified any new studies for inclusion. The review includes 14 trials (525 participants), 7 were placebo-controlled, and 7 compared diuretics against other agents such as ACE inhibitors or digoxin. We analysed the data for mortality and for worsening heart failure. Mortality data were available in 3 of the placebo-controlled trials (202 participants). Mortality was lower for participants treated with diuretics than for

The strength and failure of silica optical fibers

International Nuclear Information System (INIS)

Yan, C; Bai, R X; Yu, H; Canning, J; Law, S

2010-01-01

The mechanical strength and failure behavior of conventional and microstructured silica optical fibers was investigated using a tensile test and fracture mechanics and numerical analyses. The effect of polymer coating on failure behavior was also studied. The results indicate that all these fibers fail in a brittle manner and failure normally starts from fiber surfaces. The failure loads observed in coated fibers are higher than those in bare fibers. The introduction of air holes reduces fiber strength and their geometrical arrangements have a remarkable effect on stress distribution in the longitudinal direction. These results are potentially useful for the design, fabrication and evaluation of optical fibers for a wide range of applications.

Seismic risk analyses in the German Risk Study, phase B

International Nuclear Information System (INIS)

Hosser, D.; Liemersdorf, H.

1991-01-01

The paper discusses some aspects of the seismic risk part of the German Risk Study for Nuclear Power Plants, Phase B. First simplified analyses in Phase A of the study allowed only a rough classification of structures and systems of the PWR reference plant according to their seismic risk contribution. These studies were extended in Phase B using improved models for the dynamic analyses of buildings, structures and components as well as for the probabilistic analyses of seismic loading, failure probabilities and event trees. The methodology of deriving probabilistic seismic load descriptions is explained and compared with the methods in Phase A of the study and in other studies. Some details of the linear and nonlinear dynamic analyses of structures are reported in order to demonstrate the influence of different assumptions for material behaviour and failure criteria. The probabilistic structural and event tree analyses are discussed with respect to distribution assumptions, acceptable simplifications and model uncertainties. Some results for the PWR reference plant are given. (orig.)

Structural failure analysis of reactor vessels due to molten core debris

International Nuclear Information System (INIS)

Pfeiffer, P.A.

1993-01-01

Maintaining structural integrity of the reactor vessel during a postulated core melt accident is an important safety consideration in the design of the vessel. This paper addresses the failure predictions of the vessel due to thermal and pressure loadings from the molten core debris depositing on the lower head of the vessel. Different loading combinations were considered based on a wet or dry cavity and pressurization of the vessel based on operating pressure or atmospheric (pipe break). The analyses considered both short term (minutes) and long term (days) failure modes. Short term failure modes include creep at elevated temperatures and plastic instabilities of the structure. Long term failure modes are caused by creep rupture that lead to plastic instability of the structure. The analyses predict the reactor vessel will remain intact after the core melt has deposited on the lower vessel head

Failure analysis of real-time systems

International Nuclear Information System (INIS)

Jalashgar, A.; Stoelen, K.

1998-01-01

This paper highlights essential aspects of real-time software systems that are strongly related to the failures and their course of propagation. The significant influence of means-oriented and goal-oriented system views in the description, understanding and analysing of those aspects is elaborated. The importance of performing failure analysis prior to reliability analysis of real-time systems is equally addressed. Problems of software reliability growth models taking the properties of such systems into account are discussed. Finally, the paper presents a preliminary study of a goal-oriented approach to model the static and dynamic characteristics of real-time systems, so that the corresponding analysis can be based on a more descriptive and informative picture of failures, their effects and the possibility of their occurrence. (author)

Seismic ratchet-fatigue failure of piping systems

International Nuclear Information System (INIS)

Severud, L.K.; Anderson, M.J.; Lindquist, M.R.; Weiner, E.O.

1986-01-01

Failures of piping systems during earthquakes have been rare. Those that have failed were either made of brittle material such as cast iron, were rigid systems between major components where component relative seismic motions tore the pipe out of the component, or were high pressure systems where a ratchet-fatigue fracture followed a local bulging of the pipe diameter. Tests to failure of an unpressurized 3-in. and a pressurized 6-in. diameter carbon steel nuclear pipe systems subjected to high level shaking have been accomplished. Failure analyses of these tests are presented and correlated to the test results. It was found that failure of the unpressurized system could be correlated well with standard ASME type fatigue analysis predictions. Moreover, the pressurized system failure occurred in significantly less load cycles than predicted by standard fatigue analysis. However, a ratchet-fatigue and ductility exhaustion analysis of the pressurized system did correlate very well. These findings indicate modifications to design analysis methods and the present ASME Code piping design rules may be appropriate to cover the ratchet-fatigue failure mode

Monitoring failure rates of commercial implant brands; substantial equivalence in question?

Science.gov (United States)

Hujoel, Philippe; Becker, William; Becker, Burton

2013-07-01

The aim of this study was to report on the failure rates of two distinct dental implant systems in a clinical practice setting. Date of implant placement and loss were entered prospectively in a data registry system. Failure rates of two commercially pure titanium implants, one with a porous oxydized surface (POS) and the other with a chemically altered surface (CAS), were assessed using a quality control chart and survival analyses. A total of 860 POS and 759 CAS implants were placed. A warning of an increased failure rate of the CAS implant was identified by means of the quality control chart. Survival analyses indicated that the CAS implant failure rate was twice that of the POS implant (Hazard Ratio: 2.08; 95% CI: 1.33-3.28, P-value POS implant was associated with a non-significant 64% drop in the implant failure rate within less than a year (HR: 0.36; 95% CI: 0.12-1.14; P-value POS implant and an 8% failure with the CAS implant appears inconsistent with the assumption of substantial equivalence. © 2012 John Wiley & Sons A/S.

Image and Substance Failures in Regional Organisations: Causes, Consequences, Learning and Change?

Directory of Open Access Journals (Sweden)

Meng Hsuan Chou

2016-08-01

Full Text Available States often pool their sovereignty, capacity and resources to provide regionally specific public goods, such as security or trade rules, and regional organisations play important roles in international relations as institutions that attempt to secure peace and contribute to achieving other similar global policy goals. We observe failures occurring in these arrangements and activities in two areas: substance and image. To analytically account for this, we distinguish four modes of substance and image change and link these to specific types of failure and (lack of learning. To empirically ground and test our assumptions, we examine instances of image failure in ASEAN (political/security policy and substantive policy failure in EU labour migration policy. In so doing, this article contributes to several different fields of study and concepts that have hitherto rarely engaged with one another: analyses of policy failure from public policy, and regional integration concerns from area studies and international relations. We conclude with suggestions for ways forward to further analyse and understand failures at the international and supranational levels.

A new micromechanical approach of micropolar continuum modeling for 2-D periodic cellular material

Institute of Scientific and Technical Information of China (English)

Bin Niu; Jun Yan

2016-01-01

In this paper, we present a new united approach to formulate the equivalent micropolar constitutive relation of two-dimensional (2-D) periodic cellular material to capture its non-local properties and to explain the size effects in its structural analysis. The new united approach takes both the displacement compatibility and the equilibrium of forces and moments into consideration, where Taylor series expansion of the displacement and rotation fields and the extended aver-aging procedure with an explicit enforcement of equilibrium are adopted in the micromechanical analysis of a unit cell. In numerical examples, the effective micropolar constants obtained in this paper and others derived in the literature are used for the equivalent micropolar continuum simulation of cellular solids. The solutions from the equivalent analysis are compared with the discrete simulation solutions of the cellu-lar solids. It is found that the micropolar constants developed in this paper give satisfying results of equivalent analysis for the periodic cellular material.

Failures to further developing orphan medicinal products after designation granted in Europe: an analysis of marketing authorisation failures and abandoned drugs.

Science.gov (United States)

Giannuzzi, Viviana; Landi, Annalisa; Bosone, Enrico; Giannuzzi, Floriana; Nicotri, Stefano; Torrent-Farnell, Josep; Bonifazi, Fedele; Felisi, Mariagrazia; Bonifazi, Donato; Ceci, Adriana

2017-09-11

The research and development process in the field of rare diseases is characterised by many well-known difficulties, and a large percentage of orphan medicinal products do not reach the marketing approval.This work aims at identifying orphan medicinal products that failed the developmental process and investigating reasons for and possible factors influencing failures. Drugs designated in Europe under Regulation (European Commission) 141/2000 in the period 2000-2012 were investigated in terms of the following failures: (1) marketing authorisation failures (refused or withdrawn) and (2) drugs abandoned by sponsors during development.Possible risk factors for failure were analysed using statistically validated methods. This study points out that 437 out of 788 designations are still under development, while 219 failed the developmental process. Among the latter, 34 failed the marketing authorisation process and 185 were abandoned during the developmental process. In the first group of drugs (marketing authorisation failures), 50% reached phase II, 47% reached phase III and 3% reached phase I, while in the second group (abandoned drugs), the majority of orphan medicinal products apparently never started the development process, since no data on 48.1% of them were published and the 3.2% did not progress beyond the non-clinical stage.The reasons for failures of marketing authorisation were: efficacy/safety issues (26), insufficient data (12), quality issues (7), regulatory issues on trials (4) and commercial reasons (1). The main causes for abandoned drugs were efficacy/safety issues (reported in 54 cases), inactive companies (25.4%), change of company strategy (8.1%) and drug competition (10.8%). No information concerning reasons for failure was available for 23.2% of the analysed products. This analysis shows that failures occurred in 27.8% of all designations granted in Europe, the main reasons being safety and efficacy issues. Moreover, the stage of development

A PWR PCI failure criterion to burnups of 60 GW·d/t using the ENIGMA code

International Nuclear Information System (INIS)

Clarke, A.P.; Tempest, P.A.; Shea, J.H.

2000-01-01

A fuel performance modelling code (ENIGMA) has been used to analyse the empirical PCI failure criterion in terms of a clad failure stress as a function of burnup and fast neutron dose. The Studsvik database has been analysed. Results indicate a rising and then saturating failure stress with burnup and fast neutron dose. Using the PCI failure limits, equivalent to 95/95 confidence limits, an ENIGMA stress-based methodology is used to derive PWR PCI failure limits up to 60 GW·d/t U using a conservative assumption that the failure stress does not increase at high burnup and neutron dose. In addition experimental ramp data on gadolinia-doped fuel rods do not indicate any increased susceptibility to PCI failure implying that the UO 2 criterion can be used for gadolinia doped fuel. (author)

Finite-strain micromechanical model of stress-induced martensitic transformations in shape memory alloys

International Nuclear Information System (INIS)

Stupkiewicz, S.; Petryk, H.

2006-01-01

A micromechanical model of stress-induced martensitic transformation in single crystals of shape memory alloys is developed. This model is a finite-strain counterpart to the approach presented recently in the small-strain setting [S. Stupkiewicz, H. Petryk, J. Mech. Phys. Solids 50 (2002) 2303-2331]. The stress-induced transformation is assumed to proceed by the formation and growth of parallel martensite plates within the austenite matrix. Propagation of phase transformation fronts is governed by a rate-independent thermodynamic criterion with a threshold value for the thermodynamic driving force, including in this way the intrinsic dissipation due to phase transition. This criterion selects the initial microstructure at the onset of transformation and governs the evolution of the laminated microstructure at the macroscopic level. A multiplicative decomposition of the deformation gradient into elastic and transformation parts is assumed, with full account for the elastic anisotropy of the phases. The pseudoelastic behavior of Cu-Zn-Al single crystal in tension and compression is studied as an application of the model

Dependency Analysis Guidance Nordic/German Working Group on Common Cause Failure analysis. Phase 2, Development of Harmonized Approach and Applications for Common Cause Failure Quantification

Energy Technology Data Exchange (ETDEWEB)

Becker, Guenter; Johanson, Gunnar; Lindberg, Sandra; Vaurio, Jussi

2009-03-15

The Regulatory Code SSMFS 2008:1 of Swedish Radiation Safety Authority (SSM) includes requirements regarding the performance of probabilistic safety assessments (PSA), as well as PSA activities in general. Therefore, the follow-up of these activities is part of the inspection tasks of SSM. According to the SSMFS 2008:1, the safety analyses shall be based on a systematic identification and evaluation of such events, event sequences and other conditions which may lead to a radiological accident. The research report Nordic/German Working Group on Common cause Failure analysis. Phase 2 project report: Development of Harmonized Approach and Applications for Common Cause Failure Quantification has been developed under a contract with the Nordic PSA Group (NPSAG) and its German counterpart VGB, with the aim to create a common experience base for defence and analysis of dependent failures i.e. Common Cause Failures CCF. Phase 2 in this project if a deepened data analyses of CCF events and a demonstration on how the so called impact vectors can be constructed and on how CCF parameters are estimated. The word Guidance in the report title is used in order to indicate a common methodological guidance accepted by the NPSAG, based on current state of the art concerning the analysis of dependent failures and adapted to conditions relevant for Nordic sites. This will make it possible for the utilities to perform cost effective improvements and analyses. The report presents a common attempt by the authorities and the utilities to create a methodology and experience base for defence and analysis of dependent failures. The performed benchmark application has shown how important the interpretation of base data is to obtain robust CCF data and data analyses results. Good features were found in all benchmark approaches. The obtained experiences and approaches should now be used in harmonised procedures. A next step could be to develop and agree on event and formula driven impact vector

Dependency Analysis Guidance Nordic/German Working Group on Common Cause Failure analysis. Phase 2, Development of Harmonized Approach and Applications for Common Cause Failure Quantification

International Nuclear Information System (INIS)

Becker, Guenter; Johanson, Gunnar; Lindberg, Sandra; Vaurio, Jussi

2009-03-01

The Regulatory Code SSMFS 2008:1 of Swedish Radiation Safety Authority (SSM) includes requirements regarding the performance of probabilistic safety assessments (PSA), as well as PSA activities in general. Therefore, the follow-up of these activities is part of the inspection tasks of SSM. According to the SSMFS 2008:1, the safety analyses shall be based on a systematic identification and evaluation of such events, event sequences and other conditions which may lead to a radiological accident. The research report Nordic/German Working Group on Common cause Failure analysis. Phase 2 project report: Development of Harmonized Approach and Applications for Common Cause Failure Quantification has been developed under a contract with the Nordic PSA Group (NPSAG) and its German counterpart VGB, with the aim to create a common experience base for defence and analysis of dependent failures i.e. Common Cause Failures CCF. Phase 2 in this project if a deepened data analyses of CCF events and a demonstration on how the so called impact vectors can be constructed and on how CCF parameters are estimated. The word Guidance in the report title is used in order to indicate a common methodological guidance accepted by the NPSAG, based on current state of the art concerning the analysis of dependent failures and adapted to conditions relevant for Nordic sites. This will make it possible for the utilities to perform cost effective improvements and analyses. The report presents a common attempt by the authorities and the utilities to create a methodology and experience base for defence and analysis of dependent failures. The performed benchmark application has shown how important the interpretation of base data is to obtain robust CCF data and data analyses results. Good features were found in all benchmark approaches. The obtained experiences and approaches should now be used in harmonised procedures. A next step could be to develop and agree on event and formula driven impact vector

Investigation of shape memory alloy honeycombs by means of a micromechanical analysis

International Nuclear Information System (INIS)

Freed, Yuval; Aboudi, Jacob; Gilat, Rivka

2008-01-01

Shape memory alloy (SMA) honeycombs are promising new smart materials which may be used for light-weight structures, biomedical implants, actuators and active structures. In this study, the behavior of several SMA honeycomb structures is investigated by means of a continuum-based thermomechanically coupled micromechanical analysis. To this end, macroscopic inelastic stress–strain responses of several topologies are investigated, both for pseudoelasticity and for shape memory effect. It was found that the triangular topology exhibits the best performance. In addition, the initial transformation surfaces are presented for all possible combinations of applied in-plane stresses. A special two-phase microstructure that is capable of producing an overall negative coefficient of thermal expansion is suggested and studied. In this configuration, in which one of the phases is a SMA, residual strains are being generated upon recovery. Here, the negative coefficient of thermal expansion appears to be associated with a larger amount of residual strain upon recovery. Furthermore, a two-dimensional SMA re-entrant topology that generates a negative in-plane Poisson's ratio is analyzed, and the effect of the full thermomechanical coupling is examined. Finally, the response of a particular three-dimensional microstructure is studied

Micro-mechanical model for the tension-stabilized enzymatic degradation of collagen tissues

Science.gov (United States)

Nguyen, Thao; Ruberti, Jeffery

We present a study of how the collagen fiber structure influences the enzymatic degradation of collagen tissues. Experiments of collagen fibrils and tissues show that mechanical tension can slow and halt enzymatic degradation. Tissue-level experiments also show that degradation rate is minimum at a stretch level coincident with the onset of strain-stiffening in the stress response. To understand these phenomena, we developed a micro-mechanical model of a fibrous collagen tissue undergoing enzymatic degradation. Collagen fibers are described as sinusoidal elastica beams, and the tissue is described as a distribution of fibers. We assumed that the degradation reaction is inhibited by the axial strain energy of the crimped collagen fibers. The degradation rate law was calibrated to experiments on isolated single fibrils from bovine sclera. The fiber crimp and properties were fit to uniaxial tension tests of tissue strips. The fibril-level kinetic and tissue-level structural parameters were used to predict tissue-level degradation-induced creep rate under a constant applied force. We showed that we could accurately predict the degradation-induce creep rate of the pericardium and cornea once we accounted for differences in the fiber crimp structure and properties.

Development of the evaluation methods in reactor safety analyses and core characteristics

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

In order to support the safety reviews by NRA on reactor safety design including the phenomena with multiple failures, the computer codes are developed and the safety evaluations with analyses are performed in the areas of thermal hydraulics and core characteristics evaluation. In the code preparation of safety analyses, the TRACE and RELAP5 code were prepared to conduct the safety analyses of LOCA and beyond design basis accidents with multiple failures. In the core physics code preparation, the functions of sensitivity and uncertainty analysis were incorporated in the lattice physics code CASMO-4. The verification of improved CASMO-4 /SIMULATE-3 was continued by using core physics data. (author)

Nuclear reactor component populations, reliability data bases, and their relationship to failure rate estimation and uncertainty analysis

International Nuclear Information System (INIS)

Martz, H.F.; Beckman, R.J.

1981-12-01

Probabilistic risk analyses are used to assess the risks inherent in the operation of existing and proposed nuclear power reactors. In performing such risk analyses the failure rates of various components which are used in a variety of reactor systems must be estimated. These failure rate estimates serve as input to fault trees and event trees used in the analyses. Component failure rate estimation is often based on relevant field failure data from different reliability data sources such as LERs, NPRDS, and the In-Plant Data Program. Various statistical data analysis and estimation methods have been proposed over the years to provide the required estimates of the component failure rates. This report discusses the basis and extent to which statistical methods can be used to obtain component failure rate estimates. The report is expository in nature and focuses on the general philosophical basis for such statistical methods. Various terms and concepts are defined and illustrated by means of numerous simple examples

Geographic differences in heart failure trials.

Science.gov (United States)

Ferreira, João Pedro; Girerd, Nicolas; Rossignol, Patrick; Zannad, Faiez

2015-09-01

Randomized controlled trials (RCTs) are essential to develop advances in heart failure (HF). The need for increasing numbers of patients (without substantial cost increase) and generalization of results led to the disappearance of international boundaries in large RCTs. The significant geographic differences in patients' characteristics, outcomes, and, most importantly, treatment effect observed in HF trials have recently been highlighted. Whether the observed regional discrepancies in HF trials are due to trial-specific issues, patient heterogeneity, structural differences in countries, or a complex interaction between factors are the questions we propose to debate in this review. To do so, we will analyse and review data from HF trials conducted in different world regions, from heart failure with preserved ejection fraction (HF-PEF), heart failure with reduced ejection fraction (HF-REF), and acute heart failure (AHF). Finally, we will suggest objective and actionable measures in order to mitigate regional discrepancies in future trials, particularly in HF-PEF where prognostic modifying treatments are urgently needed and in which trials are more prone to selection bias, due to a larger patient heterogeneity. © 2015 The Authors European Journal of Heart Failure © 2015 European Society of Cardiology.

Void coalescence mechanism for combined tension and large amplitude cyclic shearing

DEFF Research Database (Denmark)

Nielsen, Kim Lau; Andersen, Rasmus Grau; Tvergaard, Viggo

2017-01-01

Void coalescence at severe shear deformation has been studied intensively under monotonic loading conditions, and the sequence of micro-mechanisms that governs failure has been demonstrated to involve collapse, rotation, and elongation of existing voids. Under intense shearing, the voids are flat...

Micromechanics of pressure-induced grain crushing in porous rocks

Science.gov (United States)

Zhang, Jiaxiang; Wong, Teng-Fong; Davis, Daniel M.

1990-01-01

The hydrostatic compaction behavior of a suite of porous sandstones was investigated at confining pressures up to 600 MPa and constant pore pressures ranging up to 50 MPa. These five sandstones (Boise, Kayenta, St. Peter, Berea, and Weber) were selected because of their wide range of porosity (5-35%) and grain size (60-460 μm). We tested the law of effective stress for the porosity change as a function of pressure. Except for Weber sandstone (which has the lowest porosity and smallest grain size), the hydrostat of each sandstone shows an inflection point corresponding to a critical effective pressure beyond which an accelerated, irrecoverable compaction occurs. Our microstructural observations show that brittle grain crushing initiates at this critical pressure. We also observed distributed cleavage cracking in calcite and intensive kinking in mica. The critical pressures for grain crushing in our sandstones range from 75 to 380 MPa. In general, a sandstone with higher porosity and larger grain size has a critical pressure which is lower than that of a sandstone with lower porosity and smaller grain size. We formulate a Hertzian fracture model to analyze the micromechanics of grain crushing. Assuming that the solid grains have preexisting microcracks with dimensions which scale with grain size, we derive an expression for the critical pressure which depends on the porosity, grain size, and fracture toughness of the solid matrix. The theoretical prediction is in reasonable agreement with our experimental data as well as other data from soil and rock mechanics studies for which the critical pressures range over 3 orders of magnitude.

Insights About Emergency Diesel Generator Failures from the USNRC's Common Cause Failure Database

International Nuclear Information System (INIS)

Mosleh, A.; Rasmuson, D.; Marshall, F.; Wierman, T.

1999-01-01

The US Nuclear Regulatory Commission has sponsored development of a database of common cause failure events for use in commercial nuclear power plant risk and reliability analyses. This paper presents a summary of the results from analysis of the emergency diesel generator data from the database. The presentation is limited to the overall insights, the design and manufacturing cause and the instrumentation and control sub-system

Microplasticity and fracture in a Ti-15V-3Cr-3Al-3Sn alloy

International Nuclear Information System (INIS)

Rabeeh, B.M.; Rokhlin, S.I.; Soboyejo, W.O.

1996-01-01

Linear Elasticity is generally considered to occur in most standard textbooks by the strengthening of chemical bonds in the regime below the proportional limit in most materials. In some cases, however, a number of researchers have recognized the possible role of localized microplasticity (microplasticity in this paper refers to localized plasticity on a microstructural level at stresses below the so-called bulk yield stress) in the so-called elastic deformation regime. There is, therefore, a need for careful studies of the micromechanisms of microplasticity in the so-called elastic regime. Micromechanisms of microplasticity will be presented in this paper for a metastable β Ti-15V-3Cr-3Al-3Sn (Ti-15-3) alloy deformed in incremental stages to failure under monotonic loading. Micromechanisms of tensile deformation and fracture will be elucidated for a Ti-15-3 plate with single phase β and Widmanstaetten α+β microstructures

Seismic ratchet-fatigue failure of piping systems

International Nuclear Information System (INIS)

Severud, L.K.; Anderson, M.J.; Lindquist, M.R.; Weiner, E.O.

1987-01-01

Failures of piping systems during earthquakes have been rare. Those that have failed were either made of brittle material such as cast iron, were rigid systems between major components where component relative seismic motions tore the pipe out of the component, or were high pressure systems where a ratchet-fatigue fracture followed a local bulging of the pipe diameter. Tests to failure of an unpressurized 3-inch and a pressurized 6-inch diameter carbon steel nuclear pipe systems subjected to high-level shaking have been accomplished. The high-level shaking loads needed to cause failure were much higher than ASME Code rules would permit with present design limits. Failure analyses of these tests are presented and correlated to the test results. It was found that failure of the unpressurized system could be correlated well with standard ASME type fatigue analysis predictions. Moreover, the pressurized system failure occured in significantly less load cycles than predicted by standard fatigue analysis. However, a ratchet-fatigue and ductility exhaustion analysis of the pressurized system did correlate reasonably well. These findings indicate modifications to design analysis methods and the present ASME Code piping design rules to reduce unneeded conservatisms and to cover the ratchet-fatigue failure mode may be appropriate

Characterising mechanical transmission wire ropes’ typical failure modes

Directory of Open Access Journals (Sweden)

Edgar Espejo

2007-01-01

Full Text Available The National University of Colombia’s Engineering School’s AFIS research group has helped several public and private institutions during the last five years in analysing the causes of failures presented in elevation and trans- port machinery leading to expensive consequences and even the loss of life. A group of typical wire rope failure modes have been identified, along with their common causes. These are presented in this work to offer help to our industry’s engineers and technicians, allowing them to identify possible risk situations in their routine work regarding the wire ropes which they use and approaches for carrying out wire rope failure analysis.

A New and General Formulation of the Parametric HFGMC Micromechanical Method for Three-Dimensional Multi-Phase Composites

Science.gov (United States)

Haj-Ali, Rami; Aboudi, Jacob

2012-01-01

The recent two-dimensional (2-D) parametric formulation of the high fidelity generalized method of cells (HFGMC) reported by the authors is generalized for the micromechanical analysis of three-dimensional (3-D) multiphase composites with periodic microstructure. Arbitrary hexahedral subcell geometry is developed to discretize a triply periodic repeating unit-cell (RUC). Linear parametric-geometric mapping is employed to transform the arbitrary hexahedral subcell shapes from the physical space to an auxiliary orthogonal shape, where a complete quadratic displacement expansion is performed. Previously in the 2-D case, additional three equations are needed in the form of average moments of equilibrium as a result of the inclusion of the bilinear terms. However, the present 3-D parametric HFGMC formulation eliminates the need for such additional equations. This is achieved by expressing the coefficients of the full quadratic polynomial expansion of the subcell in terms of the side or face average-displacement vectors. The 2-D parametric and orthogonal HFGMC are special cases of the present 3-D formulation. The continuity of displacements and tractions, as well as the equilibrium equations, are imposed in the average (integral) sense as in the original HFGMC formulation. Each of the six sides (faces) of a subcell has an independent average displacement micro-variable vector which forms an energy-conjugate pair with the transformed average-traction vector. This allows generating symmetric stiffness matrices along with internal resisting vectors for the subcells which enhances the computational efficiency. The established new parametric 3-D HFGMC equations are formulated and solution implementations are addressed. Several applications for triply periodic 3-D composites are presented to demonstrate the general capability and varsity of the present parametric HFGMC method for refined micromechanical analysis by generating the spatial distributions of local stress fields

micro-mechanical experimental investigation and modelling of strain and damage of argillaceous rocks under combined hydric and mechanical loads

International Nuclear Information System (INIS)

Wang, L.

2012-01-01

The hydro-mechanical behavior of argillaceous rocks, which are possible host rocks for underground radioactive nuclear waste storage, is investigated by means of micro-mechanical experimental investigations and modellings. Strain fields at the micrometric scale of the composite structure of this rock, are measured by the combination of environmental scanning electron microscopy, in situ testing and digital image correlation technique. The evolution of argillaceous rocks under pure hydric loading is first investigated. The strain field is strongly heterogeneous and manifests anisotropy. The observed nonlinear deformation at high relative humidity (RH) is related not only to damage, but also to the nonlinear swelling of the clay mineral itself, controlled by different local mechanisms depending on RH. Irreversible deformations are observed during hydric cycles, as well as a network of microcracks located in the bulk of the clay matrix and/or at the inclusion-matrix interface. Second, the local deformation field of the material under combined hydric and mechanical loadings is quantified. Three types of deformation bands are evidenced under mechanical loading, either normal to stress direction (compaction), parallel (microcracking) or inclined (shear). Moreover, they are strongly controlled by the water content of the material: shear bands are in particular prone to appear at high RH states. In view of understanding the mechanical interactions a local scale, the material is modeled as a composite made of non-swelling elastic inclusions embedded in an elastic swelling clay matrix. The internal stress field induced by swelling strain incompatibilities between inclusions and matrix, as well as the overall deformation, is numerically computed at equilibrium but also during the transient stage associated with a moisture gradient. An analytical micro-mechanical model based on Eshelby's solution is proposed. In addition, 2D finite element computations are performed. Results

Strain evolution after fiber failure in a single-fiber metal matrix composite under cyclic loading

Energy Technology Data Exchange (ETDEWEB)

Hanan, Jay C. [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States)]. E-mail: jay.hanan@okstate.edu; Mahesh, Sivasambu [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Uestuendag, Ersan [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States)]. E-mail: ersan@caltech.edu; Beyerlein, Irene J. [Theoretical Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Swift, Geoffrey A. [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States); Clausen, Bjorn [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States); Brown, Donald W. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Bourke, Mark A.M. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

2005-06-15

The evolution of in situ elastic strain with cyclic tensile loading in each phase of a single Al{sub 2}O{sub 3}-fiber/aluminum-matrix composite was studied using neutron diffraction (ND). An analytical model appropriate for metal matrix composites (MMCs) was developed to connect the measured axial strain evolution in each phase with the possible micromechanical events that could occur during loading at room temperature: fiber fracture, interfacial slipping, and matrix plastic deformation. Model interpretation showed that the elastic strain evolution in the fiber and matrix was governed by fiber fracture and interface slipping and not by plastic deformation of the matrix, whereas the macroscopic stress-strain response of the composite was influenced by all three. The combined single-fiber composite model and ND experiment introduces a new and quick engineering approach for qualifying the micromechanical response in MMCs due to cyclic loading and fiber fracture.

Strain evolution after fiber failure in a single-fiber metal matrix composite under cyclic loading

International Nuclear Information System (INIS)

Hanan, Jay C.; Mahesh, Sivasambu; Uestuendag, Ersan; Beyerlein, Irene J.; Swift, Geoffrey A.; Clausen, Bjorn; Brown, Donald W.; Bourke, Mark A.M.

2005-01-01

The evolution of in situ elastic strain with cyclic tensile loading in each phase of a single Al 2 O 3 -fiber/aluminum-matrix composite was studied using neutron diffraction (ND). An analytical model appropriate for metal matrix composites (MMCs) was developed to connect the measured axial strain evolution in each phase with the possible micromechanical events that could occur during loading at room temperature: fiber fracture, interfacial slipping, and matrix plastic deformation. Model interpretation showed that the elastic strain evolution in the fiber and matrix was governed by fiber fracture and interface slipping and not by plastic deformation of the matrix, whereas the macroscopic stress-strain response of the composite was influenced by all three. The combined single-fiber composite model and ND experiment introduces a new and quick engineering approach for qualifying the micromechanical response in MMCs due to cyclic loading and fiber fracture

Analyses of containment structures with corrosion damage

International Nuclear Information System (INIS)

Cherry, J.L.

1997-01-01

Corrosion damage that has been found in a number of nuclear power plant containment structures can degrade the pressure capacity of the vessel. This has prompted concerns regarding the capacity of corroded containments to withstand accident loadings. To address these concerns, finite element analyses have been performed for a typical PWR Ice Condenser containment structure. Using ABAQUS, the pressure capacity was calculated for a typical vessel with no corrosion damage. Multiple analyses were then performed with the location of the corrosion and the amount of corrosion varied in each analysis. Using a strain-based failure criterion, a open-quotes lower boundclose quotes, open-quotes best estimateclose quotes, and open-quotes upper boundclose quotes failure level was predicted for each case. These limits were established by: determining the amount of variability that exists in material properties of typical containments, estimating the amount of uncertainty associated with the level of modeling detail and modeling assumptions, and estimating the effect of corrosion on the material properties

Reactor Materials Program process water piping indirect failure frequency

International Nuclear Information System (INIS)

Daugherty, W.L.

1989-01-01

Following completion of the probabilistic analyses, the LOCA Definition Project has been subject to various external reviews, and as a result the need for several revisions has arisen. This report updates and summarizes the indirect failure frequency analysis for the process water piping. In this report, a conservatism of the earlier analysis is removed, supporting lower failure frequency estimates. The analysis results are also reinterpreted in light of subsequent review comments

Micromechanics of transformation fields in ageing linear viscoelastic composites: effects of phase dissolution or precipitation

Science.gov (United States)

Honorio, Tulio

2017-11-01

Transformation fields, in an affine formulation characterizing mechanical behavior, describe a variety of physical phenomena regardless their origin. Different composites, notably geomaterials, present a viscoelastic behavior, which is, in some cases of industrial interest, ageing, i.e. it evolves independently with respect to time and loading time. Here, a general formulation of the micromechanics of prestressed or prestrained composites in Ageing Linear Viscoelasticity (ALV) is presented. Emphasis is put on the estimation of effective transformation fields in ALV. The result generalizes Ageing Linear Thermo- and Poro-Viscoelasticity and it can be used in approaches coping with a phase transformation. Additionally, the results are extended to the case of locally transforming materials due to non-coupled dissolution and/or precipitation of a given (elastic or viscoelastic) phase. The estimations of locally transforming composites can be made with respect to different morphologies. As an application, estimations of the coefficient of thermal expansion of a hydrating alite paste are presented.

Ovarian failure in long-term survivors of childhood malignancy

International Nuclear Information System (INIS)

Stillman, R.J.; Schinfeld, J.S.; Schiff, I.; Gelber, R.D.; Greenberger, J.; Larson, M.; Jaffe, N.; Li, F.P.

1981-01-01

The frequency and causes of ovarian failure among 182 long-term survivors of childhood cancer were examined. Twenty-two patients (12%) had ovarian failure. Ovarian failure was found in 17 of 25 patients (68%) who had both ovaries within abdominal radiotherapy fields, in five of 35 patients (14%) whose ovaries were at the edge of the treatment field, and in none of 122 patients with one or both ovaries outside of an abdominal treatment field. Covariate and multivariate analyses of tumor type, age at diagnosis, duration of follow-up, abdominal tumor surgery, abdominal radiotherapy, number of chemotherapeutic agents administered, and cumulative doses of several drugs revealed that the location of the ovaries relative to radiation treatment fields was the only risk factor for subsequent ovarian failure

KOH concentration effect on the cycle life of nickel-hydrogen cells. IV - Results of failure analysis

Science.gov (United States)

Lim, H. S.; Verzwyvelt, S. A.

1990-01-01

Potassium hydroxide concentration effects on the cycle life of a Ni/H2 cell have been studied by carrying out a cycle life test on ten Ni/H2 boiler plate cells which contain electrolytes of various KOH concentrations. Failure analyses of these cells were carried out after completion of the life test, which accumulated up to 40,000 cycles at an 80-percent depth of discharge over a period of 3.7 years. These failure analyses included studies on changes of electrical characteristics of test cells, and component analyses after disassembly of the cell. The component analyses included visual inspections, dimensional changes, capacity measurements of nickel electrodes, scanning electron microscopy, surface area measurements, and chemical analyses. Results have indicated that failure mode and change in the nickel electrode varied as the concentration was varied, especially when the concentration was changed from 31 percent or higher to 26 percent or lower.

Job characteristics in nursing and cognitive failure at work.

Science.gov (United States)

Elfering, Achim; Grebner, Simone; Dudan, Anna

2011-06-01

Stressors in nursing put high demands on cognitive control and, therefore, may increase the risk of cognitive failures that put patients at risk. Task-related stressors were expected to be positively associated with cognitive failure at work and job control was expected to be negatively associated with cognitive failure at work. Ninety-six registered nurses from 11 Swiss hospitals were investigated (89 women, 7 men, mean age = 36 years, standard deviation = 12 years, 80% supervisors, response rate 48%). A new German version of the Workplace Cognitive Failure Scale (WCFS) was employed to assess failure in memory function, failure in attention regulation, and failure in action exertion. In linear regression analyses, WCFS was related to work characteristics, neuroticism, and conscientiousness. The German WCFS was valid and reliable. The factorial structure of the original WCF could be replicated. Multilevel regression task-related stressors and conscientiousness were significantly related to attention control and action exertion. The study sheds light on the association between job characteristics and work-related cognitive failure. These associations were unique, i.e. associations were shown even when individual differences in conscientiousness and neuroticism were controlled for. A job redesign in nursing should address task stressors.

Micromachined sensor for stress measurement and micromechanical study of free-standing thin films for MEMS applications

Science.gov (United States)

Zhang, Ping

Microelectromechanical systems (MEMS) have a wide range of applications. In the field of wireless and microwave technology, considerable attention has been given to the development and integration of MEMS-based RF (radio frequency) components. An RF MEMS switch requires low insertion loss, high isolation, and low actuation voltage - electrical aspects that have been extensively studied. The mechanical requirements of the switch, such as low sensitivity to built-in stress and high reliability, greatly depend on the micromechanical properties of the switch materials, and have not been thoroughly explored. RF MEMS switches are typically in the form of a free-standing thin film structure. Large stress gradients and across-wafer stress variations developed during fabrication severely degrade their electrical performance. A micromachined stress measurement sensor has been developed that can potentially be employed for in-situ monitoring of stress evolution and stress variation. The sensors were micromachined using five masks on two wafer levels, each measuring 5x3x1 mm. They function by means of an electron tunneling mechanism, where a 2x2 mm silicon nitride membrane elastically deflects under an applied deflection voltage via an external feedback circuitry. For the current design, the sensors are capable of measuring tensile stresses up to the GPa range under deflection voltages of 50--100 V. Sensor functionality was studied by finite element modeling and a theoretical analysis of square membrane deflection. While the mechanical properties of thin films on substrates have been extensively studied, studies of free-standing thin films have been limited due to the practical difficulties in sample handling and testing. Free-standing Al and Al-Ti thin films specimens have been successfully fabricated and microtensile and stress relaxation tests have been performed using a custom-designed micromechanical testing apparatus. A dedicated TEM (transmission electron microscopy

Practical applications of probabilistic structural reliability analyses to primary pressure systems of nuclear power plants

International Nuclear Information System (INIS)

Witt, F.J.

1980-01-01

Primary pressure systems of nuclear power plants are built to exacting codes and standards with provisions for inservice inspection and repair if necessary. Analyses and experiments have demonstrated by deterministic means that very large margins exist on safety impacting failures under normal operating and upset conditions. Probabilistic structural reliability analyses provide additional support that failures of significance are very, very remote. They may range in degree of sophistication from very simple calculations to very complex computer analyses involving highly developed mathematical techniques. The end result however should be consistent with the desired usage. In this paper a probabilistic structural reliability analysis is performed as a supplement to in-depth deterministic evaluations with the primary objective to demonstrate an acceptably low probability of failure for the conditions considered. (author)

Data collection on component malfunctions and failures of JET ICRH system

International Nuclear Information System (INIS)

Pinna, T.; Cambi, G.

2007-01-01

The objective of the activity was to collect and analyse data coming out from operating experiences gained in the Joint European Torus (JET) for the Ion Cyclotron Resonance Heating (ICRH) system in order to enrich the data collection on failures of components used in fusion facilities. Alarms/Failures and malfunctions occurred in the years of operations from March 1996 to November 2005, including information on failure modes and, where possible, causes of the failures, have been identified. Beyond information on failures and alarms events, also data related to crowbar events have been collected. About 3400 events classified as alarms or failures related to specific components or sub-systems were identified by analysing the 25 hand-written logbooks made available by the ICRH operation staff. Information about the JET pulses in which the ICRH system was operated has been extracted from the tick sheets covering the whole considered time interval. 20 hand written tick sheets cover the period from March 1996 to middle May 2003, while tick sheets recorded as excel files cover the period from May 2003 to November 2005. By analysing the tick sheets it results that the ICRH was operated during about 12000 plasma pulses. Main statistical values, such as rates of alarms/failures and corresponding standard errors and confidence intervals, have been estimated. Failure rates of systems and components have been evaluated both with regard to the ICRH operation pulses and operating days (days in which at least one ICRH module was requested to operate). Failure probabilities on demand have been evaluated with regard to number of pulses operated. Some of the results are the following: - The highest number of alarms/failures (1243) appears to be related to Erratic /No-output of the Instrumentation and Control (I and C) apparatus, followed by faults (829) of the Tetrode circuits, by faults (466) of the High Voltage Power Supply system and by faults (428) of the Tuning elements. - The

The plant-specific impact of different pressurization rates in the probabilistic estimation of containment failure modes

International Nuclear Information System (INIS)

Ahn, Kwang Il; Yang, Joon Eon; Ha, Jae Joo

2003-01-01

The explicit consideration of different pressurization rates in estimating the probabilities of containment failure modes has a profound effect on the confidence of containment performance evaluation that is so critical for risk assessment of nuclear power plants. Except for the sophisticated NUREG-1150 study, many of the recent containment performance analyses (through level 2 PSAs or IPE back-end analyses) did not take into account an explicit distinction between slow and fast pressurization in their analyses. A careful investigation of both approaches shows that many of the approaches adopted in the recent containment performance analyses exactly correspond to the NUREG-1150 approach for the prediction of containment failure mode probabilities in the presence of fast pressurization. As a result, it was expected that the existing containment performance analysis results would be subjected to greater or less conservatism in light of the ultimate failure mode of the containment. The main purpose of this paper is to assess potential conservatism of a plant-specific containment performance analysis result in light of containment failure mode probabilities

Tensile and fracture behavior of AA6061-T6 aluminum alloys: micro-mechanical approach

International Nuclear Information System (INIS)

Shen, Y.

2012-01-01

The AA6061-T6 aluminum alloy was chosen as the material for the core vessel of the future Jules Horowitz testing reactor (JHR). The objective of this thesis is to understand and model the tensile and fracture behavior of the material, as well as the origin of damage anisotropy. A micro-mechanical approach was used to link the microstructure and mechanical behavior. The microstructure of the alloy was characterized on the surface via Scanning Electron Microscopy and in the 3D volume via synchrotron X-ray tomography and laminography. The damage mechanism was identified by in-situ SEM tensile testing, ex-situ X-ray tomography and in-situ laminography on different levels of triaxiality. The observations have shown that damage nucleated at lower strains on Mg 2 Si coarse precipitates than on iron rich intermetallics. The identified scenario and the in-situ measurements were then used to develop a coupled GTN damage model incorporating nucleation, growth and coalescence of cavities formed by coarse precipitates. The relationship between the damage and the microstructure anisotropies was explained and simulated. (author)

Vulnerability Identification and Design-Improvement-Feedback using Failure Analysis of Digital Control System Designs

Energy Technology Data Exchange (ETDEWEB)

Lee, Eunchan; Bae, Yeonkyoung [Korea Hydro and Nuclear Power Co., Ltd., Daejeon (Korea, Republic of)

2013-05-15

Fault tree analyses let analysts establish the failure sequences of components as a logical model and confirm the result at the plant level. These two analyses provide insights regarding what improvements are needed to increase availability because it expresses the quantified design attribute of the system as minimal cut sets and availability value interfaced with component reliability data in the fault trees. This combined failure analysis method helps system users understand system characteristics including its weakness and strength in relation to faults in the design stage before system operation. This study explained why a digital system could have weaknesses in methods to transfer control signals or data and how those vulnerabilities could cause unexpected outputs. In particular, the result of the analysis confirmed that complex optical communication was not recommended for digital data transmission in the critical systems of nuclear power plants. Regarding loop controllers in Design A, a logic configuration should be changed to prevent spurious actuation due to a single failure, using hardware or software improvements such as cross checking between redundant modules, or diagnosis of the output signal integrity. Unavailability calculations support these insights from the failure analyses of the systems. In the near future, KHNP will perform failure mode and effect analyses in the design stage before purchasing non-safety-related digital system packages. In addition, the design requirements of the system will be confirmed based on evaluation of overall system availability or unavailability.

Effect of gamma radiation on micromechanical hardness of lead-free solder joint

Energy Technology Data Exchange (ETDEWEB)

Paulus, Wilfred [Universiti Kebangsaan Malaysia, Bangi, 43600 Kajang, Selangor (Malaysia); Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia); Rahman, Irman Abdul; Jalar, Azman; Kamil, Insan; Bakar, Maria Abu [Universiti Kebangsaan Malaysia, Bangi, 43600 Kajang, Selangor (Malaysia); Yusoff, Wan Yusmawati Wan [Universiti Pertahanan Nasional Malaysia, Kem Sg. Besi, 57000 Kuala Lumpur (Malaysia)

2015-09-25

Lead-free solders are important material in nano and microelectronic surface mounting technology for various applications in bio medicine, environmental monitoring, spacecraft and satellite instrumentation. Nevertheless solder joint in radiation environment needs higher reliability and resistance to any damage caused by ionizing radiations. In this study a lead-free 99.0Sn0.3Ag0.7Cu wt.% (SAC) solder joint was developed and subjected to various doses of gamma radiation to investigate the effects of the ionizing radiation to micromechanical hardness of the solder. Averaged hardness of the SAC joint was obtained from nanoindentation test. The results show a relationship between hardness values of indentations and the increment of radiation dose. Highest mean hardness, 0.2290 ± 0.0270 GPa was calculated on solder joint which was exposed to 5 Gray dose of gamma radiation. This value indicates possible radiation hardening effect on irradiated solder. The hardness gradually decreased to 0.1933 ± 0.0210 GPa and 0.1631 ± 0.0173 GPa when exposed to doses 50 and 500 gray respectively. These values are also lower than the hardness of non irradiated sample which was calculated as 0.2084 ± 0.0.3633 GPa indicating possible radiation damage and needs further related atomic dislocation study.

Micromechanical Properties of a New Polymeric Microcapsule for Self-Healing Cementitious Materials

Directory of Open Access Journals (Sweden)

Leyang Lv

2016-12-01

Full Text Available Self-healing cementitious materials containing a microencapsulated healing agent are appealing due to their great application potential in improving the serviceability and durability of concrete structures. In this study, poly(phenol–formaldehyde (PF microcapsules that aim to provide a self-healing function for cementitious materials were prepared by an in situ polymerization reaction. Size gradation of the synthesized microcapsules was achieved through a series of sieving processes. The shell thickness and the diameter of single microcapsules was accurately measured under environmental scanning electron microscopy (ESEM. The relationship between the physical properties of the synthesized microcapsules and their micromechanical properties were investigated using nanoindentation. The results of the mechanical tests show that, with the increase of the mean size of microcapsules and the decrease of shell thickness, the mechanical force required to trigger the self-healing function of microcapsules increased correspondingly from 68.5 ± 41.6 mN to 198.5 ± 31.6 mN, featuring a multi-sensitive trigger function. Finally, the rupture behavior and crack surface of cement paste with embedded microcapsules were observed and analyzed using X-ray computed tomography (XCT. The synthesized PF microcapsules may find potential application in self-healing cementitious materials.

Analysing a Chinese Regional Integrated Healthcare Organisation Reform Failure using a Complex Adaptive System Approach

Directory of Open Access Journals (Sweden)

Wenxi Tang

2017-06-01

Full Text Available Introduction: China’s organised health system has remained outdated for decades. Current health systems in many less market-oriented countries still adhere to traditional administrative-based directives and linear planning. Furthermore, they neglect the responsiveness and feedback of institutions and professionals, which often results in reform failure in integrated care. Complex adaptive system theory (CAS provides a new perspective and methodology for analysing the health system and policy implementation.  Methods: We observed the typical case of Qianjiang’s Integrated Health Organization Reform (IHO for 2 years to analyse integrated care reforms using CAS theory. Via questionnaires and interviews, we observed 32 medical institutions and 344 professionals. We compared their cooperative behaviours from both organisational and inter-professional levels between 2013 and 2015, and further investigated potential reasons for why medical institutions and professionals did not form an effective IHO. We discovered how interested parties in the policy implementation process influenced reform outcome, and by theoretical induction, proposed a new semi-organised system and corresponding policy analysis flowchart that potentially suits the actual realisation of CAS.  Results: The reform did not achieve its desired effect. The Qianjiang IHO was loosely integrated rather than closely integrated, and the cooperation levels between organisations and professionals were low. This disappointing result was due to low mutual trust among IHO members, with the main contributing factors being insufficient financial incentives and the lack of a common vision.  Discussion and Conclusions: The traditional 'organised health system' is old-fashioned. Rather than being completely organised or adaptive, the health system is currently more similar to a s'emi-organised system'. Medical institutions and professionals operate in a middle ground between complete adherence

Distributions of component failure rates, estimated from LER data

International Nuclear Information System (INIS)

Atwood, C.L.

1985-01-01

Past analyses of Licensee Event Report (LER) data have noted that component failure rates vary from plant to plant, and have estimated the distributions by two-parameter γ distributions. In this study, a more complicated distributional form is considered, a mixture of γs. This could arise if the plants' failure rates cluster into distinct groups. The method was applied to selected published LER data for diesel generators, pumps, valves, and instrumentation and control assemblies. The improved fits from using a mixture rather than a single γ distribution were minimal, and not statistically significant. There seem to be two possibilities: either explanatory variables affect the failure rates only in a gradual way, not a qualitative way; or, for estimating individual component failure rates, the published LER data have been analyzed to the limit of resolution

Experimental and analytical studies on creep failure of reactor coolant piping

Energy Technology Data Exchange (ETDEWEB)

Maeda, Akio; Maruyama, Yu; Hashimoto, Kazuichiro; Harada, Yuhei; Shibazaki, Hiroaki; Kudo, Tamotsu; Hidaka, Akihide; Sugimoto, Jun [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Nakamura, N.

1999-07-01

Thermal and structural responses of reactor coolant piping under and elevated internal pressure and temperature are being investigated in WIND project at JAERI. In a recent failure test in which a nuclear grade type 316 stainless steel pipe with an outer diameter of 114.3 mm and a wall thickness of 13.5 mm was used and an internal pressure was kept at approximately 15 MPa. A failure of the piping was observed when the temperature was sustained at 970degC for one hour. In parallel with conducting the tests, post-test analyses were performed. The objective of the analyses is to assess analytical models for the creep deformation and failure of the piping at elevated internal pressure and temperature simulating thermal-hydraulic conditions during a severe accident. The major material properties needed for the analysis were measured at elevated temperatures. Coefficients of a creep constitutive equation including the tertiary stage were determined with the measured creep data and incorporated into ABAQUS code. The analysis reasonably reproduced the time history of the enlargement of the piping diameter, and the wall thickness and the diameter of the piping at the failure. It was also found that the piping failure timing obtained from the analysis agreed well with the test result. (author)

Experimental and analytical studies on creep failure of reactor coolant piping

International Nuclear Information System (INIS)

Maeda, Akio; Maruyama, Yu; Hashimoto, Kazuichiro; Harada, Yuhei; Shibazaki, Hiroaki; Kudo, Tamotsu; Hidaka, Akihide; Sugimoto, Jun; Nakamura, N.

1999-01-01

Thermal and structural responses of reactor coolant piping under and elevated internal pressure and temperature are being investigated in WIND project at JAERI. In a recent failure test in which a nuclear grade type 316 stainless steel pipe with an outer diameter of 114.3 mm and a wall thickness of 13.5 mm was used and an internal pressure was kept at approximately 15 MPa. A failure of the piping was observed when the temperature was sustained at 970degC for one hour. In parallel with conducting the tests, post-test analyses were performed. The objective of the analyses is to assess analytical models for the creep deformation and failure of the piping at elevated internal pressure and temperature simulating thermal-hydraulic conditions during a severe accident. The major material properties needed for the analysis were measured at elevated temperatures. Coefficients of a creep constitutive equation including the tertiary stage were determined with the measured creep data and incorporated into ABAQUS code. The analysis reasonably reproduced the time history of the enlargement of the piping diameter, and the wall thickness and the diameter of the piping at the failure. It was also found that the piping failure timing obtained from the analysis agreed well with the test result. (author)

Failure analysis of the cement mantle in total hip arthroplasty with an efficient probabilistic method.

Science.gov (United States)

Kaymaz, Irfan; Bayrak, Ozgu; Karsan, Orhan; Celik, Ayhan; Alsaran, Akgun

2014-04-01

Accurate prediction of long-term behaviour of cemented hip implants is very important not only for patient comfort but also for elimination of any revision operation due to failure of implants. Therefore, a more realistic computer model was generated and then used for both deterministic and probabilistic analyses of the hip implant in this study. The deterministic failure analysis was carried out for the most common failure states of the cement mantle. On the other hand, most of the design parameters of the cemented hip are inherently uncertain quantities. Therefore, the probabilistic failure analysis was also carried out considering the fatigue failure of the cement mantle since it is the most critical failure state. However, the probabilistic analysis generally requires large amount of time; thus, a response surface method proposed in this study was used to reduce the computation time for the analysis of the cemented hip implant. The results demonstrate that using an efficient probabilistic approach can significantly reduce the computation time for the failure probability of the cement from several hours to minutes. The results also show that even the deterministic failure analyses do not indicate any failure of the cement mantle with high safety factors, the probabilistic analysis predicts the failure probability of the cement mantle as 8%, which must be considered during the evaluation of the success of the cemented hip implants.

Beyond reliability, multi-state failure analysis of satellite subsystems: A statistical approach

International Nuclear Information System (INIS)

Castet, Jean-Francois; Saleh, Joseph H.

2010-01-01

Reliability is widely recognized as a critical design attribute for space systems. In recent articles, we conducted nonparametric analyses and Weibull fits of satellite and satellite subsystems reliability for 1584 Earth-orbiting satellites launched between January 1990 and October 2008. In this paper, we extend our investigation of failures of satellites and satellite subsystems beyond the binary concept of reliability to the analysis of their anomalies and multi-state failures. In reliability analysis, the system or subsystem under study is considered to be either in an operational or failed state; multi-state failure analysis introduces 'degraded states' or partial failures, and thus provides more insights through finer resolution into the degradation behavior of an item and its progression towards complete failure. The database used for the statistical analysis in the present work identifies five states for each satellite subsystem: three degraded states, one fully operational state, and one failed state (complete failure). Because our dataset is right-censored, we calculate the nonparametric probability of transitioning between states for each satellite subsystem with the Kaplan-Meier estimator, and we derive confidence intervals for each probability of transitioning between states. We then conduct parametric Weibull fits of these probabilities using the Maximum Likelihood Estimation (MLE) approach. After validating the results, we compare the reliability versus multi-state failure analyses of three satellite subsystems: the thruster/fuel; the telemetry, tracking, and control (TTC); and the gyro/sensor/reaction wheel subsystems. The results are particularly revealing of the insights that can be gleaned from multi-state failure analysis and the deficiencies, or blind spots, of the traditional reliability analysis. In addition to the specific results provided here, which should prove particularly useful to the space industry, this work highlights the importance

Spirituality and well being among elders: differences between elders with heart failure and those without heart failure

Directory of Open Access Journals (Sweden)

Mary T Quinn Griffin

2008-01-01

Full Text Available Mary T Quinn Griffin1, Yi-Hui Lee2, Ali Salman1, Yaewon Seo1, Patricia A Marin3, Randall C Starling3, Joyce J Fitzpatrick11Frances Payne Bolton School of Nursing Case Western Reserve University Cleveland, OH; 2College of Nursing and Health Wright State University Dayton, OH; 3Cleveland Clinic, Cleveland, OhioAbstract: Heart failure is a chronic debilitating disease that affects all aspects of a person’s life, including physical, mental and spiritual dimensions. The associations among these dimensions, and the relationship to overall health status, have not been clearly identified. The purpose of this quantitative, descriptive study was to explore differences between spirituality, depressive symptoms, and quality of life among elders with and without heart failure. A total of 44 elders with heart failure and 40 non-heart failure elders completed several questionnaires including: The Daily Spiritual Experiences Scale (DSES, Spirituality Index of Well-Being (SIWB, Center for Epidemiologic Studies Depression Scale (CES-D, and SF-12™ Health Survey. There were significant differences in the groups on gender and ethnicity; thus these variables were controlled in the analyses related to the dependent variables. After controlling for gender and ethnicity, there were significant differences in the physical component of quality of life and spiritual well-being. The heart failure patients had significantly lower physical quality of life but more spiritual well-being than the non-heart failure patients. There were no significant differences in daily spiritual experiences, mental component of quality of life, and depressive symptoms between the two groups.Keywords: spiritual experience, spiritual well-being, heart failure, depressive symptoms, quality of life, elders

Preparing for Failure

International Nuclear Information System (INIS)

Murphy, L.T.; Manson, A.W.

2006-01-01

Risk management is one of the most complex project management processes, requiring rigorous management and discipline. Unfortunately, for many organizations, the risk management process has become contaminated by poor management practices, an absence of meaningful risk assessments, meaningless risk event descriptions, incomplete and vague risk impact analyses, poor follow through on risk mitigation activities and a general lack of attention to accuracy, completeness and quality. At this point, the risk register, instead of being a key tool used by the organization to systematically identify and eliminate risk, while exploiting opportunities, has become a list of pre-prepared excuses based on the repeat of failures encountered on past projects. However, organizations are not condemned to repeat past failures. By returning to the basics of risk management, and through the application of some basic management guidelines, the risk register-instead of being an 'Excuse Register' - can become the cornerstone of a comprehensive risk management program to promote a systematic, pro-active approach within an organization that will result in accomplishing mitigation activities, reducing risk and gaining advantage through opportunities. (authors)

Issues and approaches in risk-based aging analyses of passive components

International Nuclear Information System (INIS)

Uryasev, S.P.; Samanta, P.K.; Vesely, W.E.

1994-01-01

In previous NRC-sponsored work a general methodology was developed to quantify the risk contributions from aging components at nuclear plants. The methodology allowed Probabilistic Risk Analyses (PRAs) to be modified to incorporate the age-dependent component failure rates and also aging maintenance models to evaluate and prioritize the aging contributions from active components using the linear aging failure rate model and empirical components aging rates. In the present paper, this methodology is extended to passive components (for example, the pipes, heat exchangers, and the vessel). The analyses of passive components bring in issues different from active components. Here, we specifically focus on three aspects that need to be addressed in risk-based aging prioritization of passive components

Failure mode and effects analysis applied to the administration of liquid medication by oral syringes

Directory of Open Access Journals (Sweden)

Eva María Guerra-Alia

2017-11-01

Full Text Available To carry out a Failure Mode and Effects Analysis (FMEA to the use of oral syringes. Methods: A multidisciplinary team was assembled within the Safety Committee. The stages of oral administration process of liquid medication were analysed, identifying the most critical and establishing the potential modes of failure that can cause errors. The impact associated with each mode of failure was calculated using the Risk Priority Number (RPN. Preventive actions were proposed. Results: Five failure modes were identified, all classified as high risk (RPN> 100. Seven of the eight preventive actions were implemented. Conclusions: The FMEA methodology was a useful tool. It has allowed to know the risks, analyse the causes that cause them, their effects on patient safety and the measures to reduce them

Deep x-ray lithography for micromechanics and precision engineering

International Nuclear Information System (INIS)

Guckel, H.

1996-01-01

Micromechanics, an emerging technology for sensor and actuator fabrication, has already been exploited in the sensor area. Progress in actuators, devices that modify their environment and are fundamentally three dimensional, has been much more modest and is suffering from the availability of a fabrication tool with the necessary attributes. If the tool is based on photoresist technology, requirements include very large structure heights: in the millimeter range, for mask-defined prismatic photoresist shapes with flanks that differ from 90 degrees by less than 15 arc-seconds. Photoresist procedures that lead to these results are very different from their counterparts in the microelectronic industry. Thus, application is based on precast sheets of polymethyl methacrylate, PMMA, and solvent bonding followed by precision fly-cutting. Exposure is based on well-collimated x-ray sources, synchrotrons, with flux densities that can deposit 1,600 Joules per cubic centimeter in a finite time at the correct photoresist depth. Since PMMA has an absorption length that varies with photon energy, it is 100 micrometer at 3000 eV and increases to 1 cm at 20,000 eV, beamline and exposure designs center on transmission filters that control the low energy portion of the synchrotron spectrum. Since exposure latitude is large, overexposure by a factor of 15 is allowed, beamline and exposure design are relatively simple. Experiments via the Wisconsin machine, Aladdin, and the Brookhaven 2.6-GeV ring are being used to study the effectiveness issue of manufacturing with synchrotron radiation. Actuator test vehicles are linear and rotational magnetic micromotors with force outputs in the milli-Newton range. High energy exposures have produced large parts with submicron precision that are finding applications in ink jet printing and precision injection molding procedures. Both device types are unique to x-ray assisted processing. copyright 1996 American Institute of Physics

Consequences of Location-Dependent Organ of Corti Micro-Mechanics.

Directory of Open Access Journals (Sweden)

Yanju Liu

Full Text Available The cochlea performs frequency analysis and amplification of sounds. The graded stiffness of the basilar membrane along the cochlear length underlies the frequency-location relationship of the mammalian cochlea. The somatic motility of outer hair cell is central for cochlear amplification. Despite two to three orders of magnitude change in the basilar membrane stiffness, the force capacity of the outer hair cell's somatic motility, is nearly invariant over the cochlear length. It is puzzling how actuators with a constant force capacity can operate under such a wide stiffness range. We hypothesize that the organ of Corti sets the mechanical conditions so that the outer hair cell's somatic motility effectively interacts with the media of traveling waves-the basilar membrane and the tectorial membrane. To test this hypothesis, a computational model of the gerbil cochlea was developed that incorporates organ of Corti structural mechanics, cochlear fluid dynamics, and hair cell electro-physiology. The model simulations showed that the micro-mechanical responses of the organ of Corti are different along the cochlear length. For example, the top surface of the organ of Corti vibrated more than the bottom surface at the basal (high frequency location, but the amplitude ratio was reversed at the apical (low frequency location. Unlike the basilar membrane stiffness varying by a factor of 1700 along the cochlear length, the stiffness of the organ of Corti complex felt by the outer hair cell remained between 1.5 and 0.4 times the outer hair cell stiffness. The Y-shaped structure in the organ of Corti formed by outer hair cell, Deiters cell and its phalange was the primary determinant of the elastic reactance imposed on the outer hair cells. The stiffness and geometry of the Deiters cell and its phalange affected cochlear amplification differently depending on the location.

Thermo-mechanical failure criteria for x-ray windows and filters and comparison with experiments

International Nuclear Information System (INIS)

Wang, Z.; Kuzay, T.M.

1993-01-01

Synchrotron x-ray windows are vacuum separators and are usually made of thin beryllium metal. Filters are provided upstream of the window to filter out the soft x-rays to protect the window from overheating and failing. The filters are made of thin carbon products or sometimes beryllium, the same material as the window. Because the window is a vacuum separator, understanding its potential structural failure under thermal load is very important. Current structural failure models for the brazed windows and filters under thermal stresses are not very accurate. Existing models have been carefully examined and found to be inconsistent with the actual failure modes of windows tested. Due to the thinness of the filter/window, the most likely failure mode is thermal buckling. In fact, recent synchrotron tests conducted in Japan on window failures bear out this position. In this paper, failure criteria for filters/windows are proposed, and analyses are performed and compared with the experimental results from various sources. A consistent result is found between the analysis and reported experiments. A series of additional analyses based on the proposed failure criteria is also carried out for filter and window designs for the third generation synchrotron beamline front ends. Comparative results are presented here

Distributions of component failure rates estimated from LER data

International Nuclear Information System (INIS)

Atwood, C.L.

1985-01-01

Past analyses of Licensee Event Report (LER) data have noted that component failure rates vary from plant to plant, and have estimated the distributions by two-parameter gamma distributions. In this study, a more complicated distributional form is considered, a mixture of gammas. This could arise if the plants' failure rates cluster into distinct groups. The method was applied to selected published LER data for diesel generators, pumps, valves, and instrumentation and control assemblies. The improved fits from using a mixture rather than a single gamma distribution were minimal, and not statistically significant. There seem to be two possibilities: either explanatory variables affect the failure rates only in a gradual way, not a qualitative way; or, for estimating individual component failure rates, the published LER data have been analyzed to the limit of resolution. 9 refs

Defibrillator Implantation in Patients with Nonischemic Systolic Heart Failure

DEFF Research Database (Denmark)

Køber, Lars; Thune, Jens J; Nielsen, Jens C

2016-01-01

Background The benefit of an implantable cardioverter-defibrillator (ICD) in patients with symptomatic systolic heart failure caused by coronary artery disease has been well documented. However, the evidence for a benefit of prophylactic ICDs in patients with systolic heart failure that is not due...... to coronary artery disease has been based primarily on subgroup analyses. The management of heart failure has improved since the landmark ICD trials, and many patients now receive cardiac resynchronization therapy (CRT). Methods In a randomized, controlled trial, 556 patients with symptomatic systolic heart.......6%) in the control group (P=0.29). Conclusions In this trial, prophylactic ICD implantation in patients with symptomatic systolic heart failure not caused by coronary artery disease was not associated with a significantly lower long-term rate of death from any cause than was usual clinical care. (Funded by Medtronic...

Structural analyses of ITER toroidal field coils under fault conditions

International Nuclear Information System (INIS)

Jong, C.T.J.

1992-04-01

ITER (International Thermonuclear Experimental Reactor) is intended to be an experimental thermonuclear tokamak reactor testing the basic physics performance and technologies essential to future fusion reactors. The magnet system of ITER consists essentially of 4 sub-systems, i.e. toroidal field coils (TFCs), poloidal field coils (PFCs), power supplies, and cryogenic supplies. These subsystems do not contain significant radioactivity inventories, but the large energy inventory is a potential accident initiator. The aim of the structural analyses is to prevent accidents from propagating into vacuum vessel, tritium system and cooling system, which all contain significant amounts of radioactivity. As part of design process 3 conditions are defined for PF and TF coils, at which mechanical behaviour has to be analyzed in some detail, viz: normal operating conditions, upset conditions and fault conditions. This paper describes the work carried out by ECN to create a detailed finite element model of 16 TFCs as well as results of some fault condition analyses made with the model. Due to fault conditions, either electrical or mechanical, magnetic loading of TFCs becomes abnormal and further mechanical failure of parts of the overall structure might occur (e.g. failure of coil, gravitational supports, intercoil structure). The analyses performed consist of linear elastic stress analyses and electro-magneto-structural analyses (coupled field analyses). 8 refs.; 5 figs.; 5 tabs

On experiments to detect possible failures on relativity theory

International Nuclear Information System (INIS)

Rodrigues Junior, W.A.; Tiomno, J.

1982-01-01

Conditions under which is expected the failure of Einstein's Relativity are analysed. A complete analysis of a recently proposed experiment by Kolen-Torr is also given showing that it must give a negative result. (Author) [pt

Fatigue crack micromechanisms in a Cu-Zn-Al shape memory alloy with pseudo-elastic behavior

Directory of Open Access Journals (Sweden)

Vittorio Di Cocco

2015-10-01

Full Text Available Shape memory property characterizes the behavior of many Ti based and Cu based alloys (SMAs. In Cu-Zn-Al SMAs, the original shape recovering is due to a bcc phase that is stable at high temperature. After an appropriate cooling process, this phase (β-phase or austenitic phase transforms reversibly into a B2 structure (transition phase and, after a further cooling process or a plastic deformation, it transforms into a DO3 phase (martensitic phase. In β-Cu-Zn-Al SMAs, the martensitic transformation due to plastic deformation is not stable at room temperature: a high temperature “austenitization” process followed by a high speed cooling process allow to obtain a martensitic phase with a higher stability. In this work, a Cu-Zn-Al SMA in “as cast” conditions has been microstructurally and metallographically characterized by means of X-Ray diffraction and Light Optical Microscope (LOM observations. Fatigue crack propagation resistance and damaging micromechanisms have been investigated corresponding to three different load ratios (R=0.10, 0.50 and 0.75

Goal-oriented failure analysis - a systems analysis approach to hazard identification

International Nuclear Information System (INIS)

Reeves, A.B.; Davies, J.; Foster, J.; Wells, G.L.

1990-01-01

Goal-Oriented Failure Analysis, GOFA, is a methodology which is being developed to identify and analyse the potential failure modes of a hazardous plant or process. The technique will adopt a structured top-down approach, with a particular failure goal being systematically analysed. A systems analysis approach is used, with the analysis being organised around a systems diagram of the plant or process under study. GOFA will also use checklists to supplement the analysis -these checklists will be prepared in advance of a group session and will help to guide the analysis and avoid unnecessary time being spent on identifying obvious failure modes or failing to identify certain hazards or failures. GOFA is being developed with the aim of providing a hazard identification methodology which is more efficient and stimulating than the conventional approach to HAZOP. The top-down approach should ensure that the analysis is more focused and the use of a systems diagram will help to pull the analysis together at an early stage whilst also helping to structure the sessions in a more stimulating way than the conventional techniques. GOFA will be, essentially, an extension of the HAZOP methodology. GOFA is currently being computerised using a knowledge-based systems approach for implementation. The Goldworks II expert systems development tool is being used. (author)

Capacity for diagnosis and treatment of heart failure in sub-Saharan Africa.

Science.gov (United States)

Carlson, Selma; Duber, Herbert C; Achan, Jane; Ikilezi, Gloria; Mokdad, Ali H; Stergachis, Andy; Wollum, Alexandra; Bukhman, Gene; Roth, Gregory A

2017-12-01

Heart failure is a major cause of disease burden in sub-Saharan Africa (SSA). There is an urgent need for better strategies for heart failure management in this region. However, there is little information on the capacity to diagnose and treat heart failure in SSA. We aim to provide a better understanding of the capacity to diagnose and treat heart failure in Kenya and Uganda to inform policy planning and interventions. We analysed data from a nationally representative survey of health facilities in Kenya and Uganda (197 health facilities in Uganda and 143 in Kenya). We report on the availability of cardiac diagnostic technologies and select medications for heart failure (β-blockers, ACE inhibitors and furosemide). Facility-level data were analysed by country and platform type (hospital vs ambulatory facilities). Functional and staffed radiography, ultrasound and ECG were available in less than half of hospitals in Kenya and Uganda combined. Of the hospitals surveyed, 49% of Kenyan and 77% of Ugandan hospitals reported availability of the heart failure medication package. ACE inhibitors were only available in 51% of Kenyan and 79% of Ugandan hospitals. Almost one-third of the hospitals in each country had a stock-out of at least one of the medication classes in the prior quarter. Few facilities in Kenya and Uganda were prepared to diagnose and manage heart failure. Medication shortages and stock-outs were common. Our findings call for increased investment in cardiac care to reduce the growing burden of heart failure. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Overview and statistical failure analyses of the electrical insulation system for the SSC long dipole magnets from an industrialization point of view

International Nuclear Information System (INIS)

Roach, J.F.

1992-01-01

The electrical insulation system of the SSC long dipole magnets is reviewed and potential dielectric failure modes discussed. Electrical insulation fabrication and assembly issues with respect to rate production manufacturability are addressed. The automation required for rate assembly of electrical insulation components will require critical online visual and dielectric screening tests to insure production quality. Storage and assembly areas must bc designed to prevent foreign particles from becoming entrapped in the insulation during critical coil winding, molding, and collaring operations. All hand assembly procedures involving dielectrics must be performed with rigorous attention to their impact on insulation integrity. Individual dipole magnets must have a sufficiently low probability of electrical insulation failure under all normal and fault mode voltage conditions such that the series of magnets in the SSC rings have acceptable Mean Time Between Failure (MTBF) with respect to dielectric mode failure events. Statistical models appropriate for large electrical system breakdown failure analysis are applied to the SSC magnet rings. The MTBF of the SSC system is related to failure data base for individual dipole magnet samples

Interim report on the state-of-the-art of solid-state motor controllers. Part 4. Failure-rate and failure-mode data

International Nuclear Information System (INIS)

Jaross, R.A.

1983-09-01

An assessment of the reliability of solid-state motor controllers for nuclear power plants is made. Available data on failure-rate and failure-mode data for solid-state motor controllers based on industrial operating experience is meager; the data are augmented by data on other solid-state power electronic devices that are shown to have components similar to those found in solid-state motor controllers. In addition to large nonnuclear solid-state adjustable-speed motor drives, the reliability of nuclear plant inverter systems and high-voltage solid-state dc transmission-line converters is assessed. Licensee Event Report analyses from several sources, the open literature, and personal communications are used to determine the realiability of solid-state devices typical of those expected to be used in nuclear power plants in terms of failures per hour

Failure Mechanisms of Brittle Rocks under Uniaxial Compression

Science.gov (United States)

Liu, Taoying; Cao, Ping

2017-09-01

The behaviour of a rock mass is determined not only by the properties of the rock matrix, but mostly by the presence and properties of discontinuities or fractures within the mass. The compression test on rock-like specimens with two prefabricated transfixion fissures, made by pulling out the embedded metal inserts in the pre-cured period was carried out on the servo control uniaxial loading tester. The influence of the geometry of pre-existing cracks on the cracking processes was analysed with reference to the experimental observation of crack initiation and propagation from pre-existing flaws. Based on the rock fracture mechanics and the stress-strain curves, the evolution failure mechanism of the fissure body was also analyzed on the basis of exploring the law of the compression-shear crack initiation, wing crack growth and rock bridge connection. Meanwhile, damage fracture mechanical models of a compression-shear rock mass are established when the rock bridge axial transfixion failure, tension-shear combined failure, or wing crack shear connection failure occurs on the specimen under axial compression. This research was of significance in studying the failure mechanism of fractured rock mass.

Fracture mechanics evaluation of feedwater line failure at Surry-2: Final report

International Nuclear Information System (INIS)

Zahoor, A.; Gamble, R.M.

1987-10-01

The purpose of this work was to perform a fracture mechanics evaluation of a failure that occurred in an elbow of the 18-inch suction line to the ''A'' main feed pump at Surry Power Station, Unit 2. The failure occurred during a pressure transient subsequent to a reactor trip, which was initiated by a low-low steam generator level protection signal. Analyses were performed to characterize the crack formation and growth sequence at the estimated failure pressure (550 psi) and normal operating pressure (367 psi); this work included predicting the longitudinal throughwall crack lengths for initial wall breakthrough and failure. A sensitivity study also was performed to assess the effect on the results of variations in several conditions that generally influence failure

Fracture mechanics evaluation of feedwater line failure at Surry-2: Final report

Energy Technology Data Exchange (ETDEWEB)

Zahoor, A.; Gamble, R.M.

1987-10-01

The purpose of this work was to perform a fracture mechanics evaluation of a failure that occurred in an elbow of the 18-inch suction line to the ''A'' main feed pump at Surry Power Station, Unit 2. The failure occurred during a pressure transient subsequent to a reactor trip, which was initiated by a low-low steam generator level protection signal. Analyses were performed to characterize the crack formation and growth sequence at the estimated failure pressure (550 psi) and normal operating pressure (367 psi); this work included predicting the longitudinal throughwall crack lengths for initial wall breakthrough and failure. A sensitivity study also was performed to assess the effect on the results of variations in several conditions that generally influence failure.

Contributions to micromechanical model of the non linear behavior of the Callovo-Oxfordian argillite

International Nuclear Information System (INIS)

Abou-Chakra Guery, A.

2007-12-01

This work is performed in the general context of the project of underground disposal of radioactive waste, undertaken by the French National Radioactive Waste Management Agency (ANDRA). Due to its strong density and weak permeability, the formation of Callovo-Oxfordian argillite is chosen as one of possible geological barriers to radionuclides. The objective of the study to develop and validate a non linear homogenization approach of the mechanical behavior of Callovo-Oxfordian argillites. The material is modelled as a composite constituted of an elasto(visco)plastic clay matrix and of linear elastic or elastic damage inclusions. The macroscopic constitutive law is obtained by adapting the incremental method proposed by Hill. The derived model is first compared to Finite Element calculations on unit cell. It is then validated and applied for the prediction of the macroscopic stress-strain responses of the argillite at different geological depths. Finally, the micromechanical model is implemented in a commercial finite element code (Abaqus) for the simulation of a vertical shaft of the underground laboratory. This allows predicting the distribution of damage state and plastic strains and characterizing the excavation damage zone (EDZ). (author)

Evaluation of fracture mechanics analyses used in RPV integrity assessment regarding brittle fracture

International Nuclear Information System (INIS)

Moinereau, D.; Faidy, C.; Valeta, M.P.; Bhandari, S.; Guichard, D.

1997-01-01

Electricite de France has conducted during these last years some experimental and numerical research programmes in order to evaluate fracture mechanics analyses used in nuclear reactor pressure vessels structural integrity assessment, regarding the risk of brittle fracture. These programmes included cleavage fracture tests on large scale cladded specimens containing subclad flaws with their interpretations by 2D and 3D numerical computations, and validation of finite element codes for pressurized thermal shocks analyses. Four cladded specimens made of ferritic steel A508 C13 with stainless steel cladding, and containing shallow subclad flaws, have been tested in four point bending at very low temperature in order to obtain cleavage failure. The specimen failure was obtained in each case in base metal by cleavage fracture. These tests have been interpreted by two-dimensional and three-dimensional finite element computations using different fracture mechanics approaches (elastic analysis with specific plasticity corrections, elastic-plastic analysis, local approach to cleavage fracture). The failure of specimens are conservatively predicted by different analyses. The comparison between the elastic analyses and elastic-plastic analyses shows the conservatism of specific plasticity corrections used in French RPV elastic analyses. Numerous finite element calculations have also been performed between EDF, CEA and Framatome in order to compare and validate several fracture mechanics post processors implemented in finite element programmes used in pressurized thermal shock analyses. This work includes two-dimensional numerical computations on specimens with different geometries and loadings. The comparisons show a rather good agreement on main results, allowing to validate the finite element codes and their post-processors. (author). 11 refs, 24 figs, 3 tabs

Evaluation of fracture mechanics analyses used in RPV integrity assessment regarding brittle fracture

Energy Technology Data Exchange (ETDEWEB)

Moinereau, D [Electricite de France, Dept. MTC, Moret-sur-Loing (France); Faidy, C [Electricite de France, SEPTEN, Villeurbanne (France); Valeta, M P [Commisariat a l` Energie Atomique, Dept. DMT, Gif-sur-Yvette (France); Bhandari, S; Guichard, D [Societe Franco-Americaine de Constructions Atomiques (FRAMATOME), 92 - Paris-La-Defense (France)

1997-09-01

Electricite de France has conducted during these last years some experimental and numerical research programmes in order to evaluate fracture mechanics analyses used in nuclear reactor pressure vessels structural integrity assessment, regarding the risk of brittle fracture. These programmes included cleavage fracture tests on large scale cladded specimens containing subclad flaws with their interpretations by 2D and 3D numerical computations, and validation of finite element codes for pressurized thermal shocks analyses. Four cladded specimens made of ferritic steel A508 C13 with stainless steel cladding, and containing shallow subclad flaws, have been tested in four point bending at very low temperature in order to obtain cleavage failure. The specimen failure was obtained in each case in base metal by cleavage fracture. These tests have been interpreted by two-dimensional and three-dimensional finite element computations using different fracture mechanics approaches (elastic analysis with specific plasticity corrections, elastic-plastic analysis, local approach to cleavage fracture). The failure of specimens are conservatively predicted by different analyses. The comparison between the elastic analyses and elastic-plastic analyses shows the conservatism of specific plasticity corrections used in French RPV elastic analyses. Numerous finite element calculations have also been performed between EDF, CEA and Framatome in order to compare and validate several fracture mechanics post processors implemented in finite element programmes used in pressurized thermal shock analyses. This work includes two-dimensional numerical computations on specimens with different geometries and loadings. The comparisons show a rather good agreement on main results, allowing to validate the finite element codes and their post-processors. (author). 11 refs, 24 figs, 3 tabs.

Dynamic Evolution Of Off-Fault Medium During An Earthquake: A Micromechanics Based Model

Science.gov (United States)

Thomas, M. Y.; Bhat, H. S.

2017-12-01

Geophysical observations show a dramatic drop of seismic wave speeds in the shallow off-fault medium following earthquake ruptures. Seismic ruptures generate, or reactivate, damage around faults that alter the constitutive response of the surrounding medium, which in turn modifies the earthquake itself, the seismic radiation, and the near-fault ground motion. We present a micromechanics based constitutive model that accounts for dynamic evolution of elastic moduli at high-strain rates. We consider 2D in-plane models, with a 1D right lateral fault featuring slip-weakening friction law. The two scenarios studied here assume uniform initial off-fault damage and an observationally motivated exponential decay of initial damage with fault normal distance. Both scenarios produce dynamic damage that is consistent with geological observations. A small difference in initial damage actively impacts the final damage pattern. The second numerical experiment, in particular, highlights the complex feedback that exists between the evolving medium and the seismic event. We show that there is a unique off-fault damage pattern associated with supershear transition of an earthquake rupture that could be potentially seen as a geological signature of this transition. These scenarios presented here underline the importance of incorporating the complex structure of fault zone systems in dynamic models of earthquakes.

Dynamic Evolution Of Off-Fault Medium During An Earthquake: A Micromechanics Based Model

Science.gov (United States)

Thomas, Marion Y.; Bhat, Harsha S.

2018-05-01

Geophysical observations show a dramatic drop of seismic wave speeds in the shallow off-fault medium following earthquake ruptures. Seismic ruptures generate, or reactivate, damage around faults that alter the constitutive response of the surrounding medium, which in turn modifies the earthquake itself, the seismic radiation, and the near-fault ground motion. We present a micromechanics based constitutive model that accounts for dynamic evolution of elastic moduli at high-strain rates. We consider 2D in-plane models, with a 1D right lateral fault featuring slip-weakening friction law. The two scenarios studied here assume uniform initial off-fault damage and an observationally motivated exponential decay of initial damage with fault normal distance. Both scenarios produce dynamic damage that is consistent with geological observations. A small difference in initial damage actively impacts the final damage pattern. The second numerical experiment, in particular, highlights the complex feedback that exists between the evolving medium and the seismic event. We show that there is a unique off-fault damage pattern associated with supershear transition of an earthquake rupture that could be potentially seen as a geological signature of this transition. These scenarios presented here underline the importance of incorporating the complex structure of fault zone systems in dynamic models of earthquakes.

Fuzzy-logic assessment of failure hazard in pipelines due to mining activity

Directory of Open Access Journals (Sweden)

A. A. Malinowska

2015-11-01

Full Text Available The present research is aimed at a critical analysis of a method presently used for evaluating failure hazard in linear objects in mining areas. A fuzzy model of failure hazard of a linear object was created on the basis of the experience gathered so far. The rules of Mamdani fuzzy model have been used in the analyses. Finally the scaled model was integrated with a Geographic Information System (GIS, which was used to evaluate failure hazard in a water pipeline in a mining area.

Architecture Level Safety Analyses for Safety-Critical Systems

Directory of Open Access Journals (Sweden)

K. S. Kushal

2017-01-01

Full Text Available The dependency of complex embedded Safety-Critical Systems across Avionics and Aerospace domains on their underlying software and hardware components has gradually increased with progression in time. Such application domain systems are developed based on a complex integrated architecture, which is modular in nature. Engineering practices assured with system safety standards to manage the failure, faulty, and unsafe operational conditions are very much necessary. System safety analyses involve the analysis of complex software architecture of the system, a major aspect in leading to fatal consequences in the behaviour of Safety-Critical Systems, and provide high reliability and dependability factors during their development. In this paper, we propose an architecture fault modeling and the safety analyses approach that will aid in identifying and eliminating the design flaws. The formal foundations of SAE Architecture Analysis & Design Language (AADL augmented with the Error Model Annex (EMV are discussed. The fault propagation, failure behaviour, and the composite behaviour of the design flaws/failures are considered for architecture safety analysis. The illustration of the proposed approach is validated by implementing the Speed Control Unit of Power-Boat Autopilot (PBA system. The Error Model Annex (EMV is guided with the pattern of consideration and inclusion of probable failure scenarios and propagation of fault conditions in the Speed Control Unit of Power-Boat Autopilot (PBA. This helps in validating the system architecture with the detection of the error event in the model and its impact in the operational environment. This also provides an insight of the certification impact that these exceptional conditions pose at various criticality levels and design assurance levels and its implications in verifying and validating the designs.

A bivariate model for analyzing recurrent multi-type automobile failures

Science.gov (United States)

Sunethra, A. A.; Sooriyarachchi, M. R.

2017-09-01

The failure mechanism in an automobile can be defined as a system of multi-type recurrent failures where failures can occur due to various multi-type failure modes and these failures are repetitive such that more than one failure can occur from each failure mode. In analysing such automobile failures, both the time and type of the failure serve as response variables. However, these two response variables are highly correlated with each other since the timing of failures has an association with the mode of the failure. When there are more than one correlated response variables, the fitting of a multivariate model is more preferable than separate univariate models. Therefore, a bivariate model of time and type of failure becomes appealing for such automobile failure data. When there are multiple failure observations pertaining to a single automobile, such data cannot be treated as independent data because failure instances of a single automobile are correlated with each other while failures among different automobiles can be treated as independent. Therefore, this study proposes a bivariate model consisting time and type of failure as responses adjusted for correlated data. The proposed model was formulated following the approaches of shared parameter models and random effects models for joining the responses and for representing the correlated data respectively. The proposed model is applied to a sample of automobile failures with three types of failure modes and up to five failure recurrences. The parametric distributions that were suitable for the two responses of time to failure and type of failure were Weibull distribution and multinomial distribution respectively. The proposed bivariate model was programmed in SAS Procedure Proc NLMIXED by user programming appropriate likelihood functions. The performance of the bivariate model was compared with separate univariate models fitted for the two responses and it was identified that better performance is secured by

Compressive Failure of Fibre Reinforced Materials

DEFF Research Database (Denmark)

Jensen, Henrik Myhre

2003-01-01

Compressive failure of uni-directional fibre composites by the kink band mechanism is analysed taking into account effects of residual stresses. Two criteria for determining the strength of the composite material have been investigated: Kink band formation at a bifurcation stress in a composite...... with perfectly aligned fibres, and kink band formation at a peak stress in a composite with a band of imperfect material....

Specific strain work as a failure criterion in plane stress state

International Nuclear Information System (INIS)

Zuchowski, R.; Zietkowski, L.

1985-01-01

An experimental verification of failure criterion based on specific strain work was performed. Thin-walled cylindrical specimens were examined by loading with constant force and constant torque moment, assuming different values for particular tests, at the same time keeping stress intensity constant, and by subjecting to thermal cycling. It was found that the critical value of failure did not depend on axial-to-shearing stresses ratio, i.e., on the type of state of stress. Thereby, the validity of the analysed failure criterion in plane stress was confirmed. Besides, a simple description of damage development in plane stress was suggested. (orig./RF)

Hydrate failure in ITZ governs concrete strength: A micro-to-macro validated engineering mechanics model

Czech Academy of Sciences Publication Activity Database

Königsberger, M.; Hlobil, Michal; Delsaute, B.; Staquet, S.; Hellmich, C.; Pichler, B.

2018-01-01

Roč. 103, č. 1 (2018), s. 77-94 ISSN 0008-8846 Institutional support: RVO:68378297 Keywords : compressive strength * micromechanics * cement paste * concrete * modeling Subject RIV: JM - Building Engineering OBOR OECD: Construction engineering, Municipal and structural engineering Impact factor: 4.762, year: 2016 http://www.sciencedirect.com/science/article/pii/S0008884617302934?via%3Dihub

The business concept of leader pricing as applied to heart failure disease management.

Science.gov (United States)

Hauptman, Paul J; Bednarek, Heather L

2004-01-01

The implementation of a disease management approach for patients with heart failure has been promoted as a way to improve outcomes, including a decrease in hospitalizations. However, in the absence of rigorous cost analyses and with revenues limited by professional fees, heart failure disease management programs may appear to operate at a loss. The literature outlining the importance of disease management for patients with heart failure is summarized. We review the limitations of current cost analyses and outline the economic concepts of leader pricing, vertical integration and transaction costs to argue that heart failure disease management programs may provide significant "downstream" revenue for an integrated system of health care delivery in a fee-for-service payment structure, while reducing overall costs of care. Pilot data from a university-based program are used in support of this argument. In addition, the favorable impact on patient satisfaction and loyalty can enhance market share, a vital consideration for all health systems. Options for improving the reputation of heart failure disease management within a health system are suggested. Viewed as a loss leader, disease management provides not only quality care for patients with heart failure but also appears to provide financial benefits to the health system that funds the infrastructure and administration of the program. The actual magnitude of this benefit and the degree to which it mitigates overall administration costs requires further study.

Is age a factor in the success or failure of remote monitoring in heart failure? Telemonitoring and structured telephone support in elderly heart failure patients.

Science.gov (United States)

Inglis, Sally C; Conway, Aaron; Cleland, John Gf; Clark, Robyn A

2015-06-01

There are few data regarding the effectiveness of remote monitoring for older people with heart failure. We conducted a post-hoc sub-analysis of a previously published large Cochrane systematic review and meta-analysis of relevant randomized controlled trials to determine whether structured telephone support and telemonitoring were effective in this population. A post hoc sub-analysis of a systematic review and meta-analysis that applied the Cochrane methodology was conducted. Meta-analyses of all-cause mortality, all-cause hospitalizations and heart failure-related hospitalizations were performed for studies where the mean or median age of participants was 70 or more years. The mean or median age of participants was 70 or more years in eight of the 16 (n=2659/5613; 47%) structured telephone support studies and four of the 11 (n=894/2710; 33%) telemonitoring studies. Structured telephone support (RR 0.80; 95% CI=0.63-1.00) and telemonitoring (RR 0.56; 95% CI=0.41-0.76) interventions reduced mortality. Structured telephone support interventions reduced heart failure-related hospitalizations (RR 0.81; 95% CI=0.67-0.99). Despite a systematic bias towards recruitment of individuals younger than the epidemiological average into the randomized controlled trials, older people with heart failure did benefit from structured telephone support and telemonitoring. These post-hoc sub-analysis results were similar to overall effects observed in the main meta-analysis. While further research is required to confirm these observational findings, the evidence at hand indicates that discrimination by age alone may be not be appropriate when inviting participation in a remote monitoring service for heart failure. © The European Society of Cardiology 2014.

Therapeutic patient education in heart failure: do studies provide sufficient information about the educational programme?

Science.gov (United States)

Albano, Maria Grazia; Jourdain, Patrick; De Andrade, Vincent; Domenke, Aukse; Desnos, Michel; d'Ivernois, Jean-François

2014-05-01

Therapeutic patient education programmes on heart failure have been widely proposed for many years for heart failure patients, but their efficiency remains questionable, partly because most articles lack a precise programme description, which makes comparative analysis of the studies difficult. To analyse the degree of precision in describing therapeutic patient education programmes in recent randomized controlled trials. Three major recent recommendations on therapeutic patient education in heart failure inspired us to compile a list of 23 relevant items that an 'ideal' description of a therapeutic patient education programme should contain. To discover the extent to which recent studies into therapeutic patient education in heart failure included these items, we analysed 19 randomized controlled trials among 448 articles published in this field from 2005 to 2012. The major elements required to describe a therapeutic patient education programme were present, but some other very important pieces of information were missing in most of the studies we analysed: the patient's educational needs, health literacy, projects, expectations regarding therapeutic patient education and psychosocial status; the educational methodology used; outcomes evaluation; and follow-up strategies. Research into how therapeutic patient education can help heart failure patients will be improved if more precise descriptions of patients, educational methodology and evaluation protocols are given by authors, ideally in a standardized format. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Patterns of failure for glioblastoma multiforme following concurrent radiation and temozolomide

International Nuclear Information System (INIS)

Dobelbower, Michael C.; Burnett, Omer L. III; Haytt, Mark D.; Fiveash, John B.; Nordal, Robert A.; Nabors, Louis B.; Markert, James M.

2011-01-01

To analyse patterns of failure in patients with glioblastoma multiforme treated with concurrent radiation and temozolomide. A retrospective review of patients treated with concurrent radiation and temozolomide was performed. Twenty patients treated at the University of Alabama at Birmingham, with biopsy-proven disease, documented disease progression after treatment, and adequate radiation dosimetry and imaging records were included in the study. Patients generally received 46 Gy to the primary tumour and surrounding oedema plus 1 cm, and 60 Gy to the enhancing tumour plus 1 cm. MRIs documenting failure after therapy were fused to the original treatment plans. Contours of post-treatment tumour volumes were generated from MRIs showing tumour failure and were overlaid onto the original isodose curves. The recurrent tumours were classified as in-field, marginal or regional. Recurrences were also evaluated for distant failure. Of the 20 documented failures, all patients had some component of failure at the primary site. Eighteen patients (90%) failed in-field, 2 patients (10%) had marginal failures, and no regional failures occurred. Four patients (20%) had a component of distant failure in which an independent satellite lesion was located completely outside of the 95% isodose curve. Radiation concurrent with temozolomide appears to be associated with a moderate risk of distant brain failure in addition to the high rate of local failure. The risk of distant failure was consistent with that observed with radiation alone, suggesting that temozolomide does not act to reduce distant brain failure but to improve local control.

Understanding the mechanisms that change the conductivity of damaged ITO-coated polymeric films: A micro-mechanical investigation

KAUST Repository

Nasr Saleh, Mohamed

2014-11-01

Degradation from mechanical loading of transparent electrodes made of indium tin oxide (ITO) endangers the integrity of any material based on these electrodes, including flexible organic solar cells. However, how different schemes of degradation change the conductivity of ITO devices remains unclear. We propose a systematic micro-mechanics-based approach to clarify the relationship between degradation and changes in electrical resistance. By comparing experimentally measured channel crack densities to changes in electrical resistance returned by the different micro-mechanical schemes, we highlight the key role played by the residual conductivity in the interface between the ITO electrode and its substrate after delamination. We demonstrate that channel cracking alone does not explain the experimental observations. Our results indicate that delamination has to take place between the ITO electrode and the substrate layers and that the residual conductivity of this delaminated interface plays a major role in changes in electrical resistance of the degraded device. © 2014 Elsevier B.V.

Micromechanics of Size Effect in Failure Due to Distributed Cracking

Science.gov (United States)

1990-02-26

U0 = ub+ us U9Ub 3 (s WE 4bd E where L is the span of the specimen, and ub and us are the contributions of bending and shear, respectively. The weight...0r- r- C ’= 0 "t M = ’- cr; Ej= -- * -r C + .0-~ - - - :3~~~~. C5r r-C -s t 1L C E 7S Iu.Cf~ ejr0C.C..~0~3J ~ ~c- 0 11 tD r =- -11 (10 21 mC CC c lC...w cc 77- -. 1 Z ~ - aCIOC0 aL -, v . ~ v: : . 4J 0 ftU L-< a ~ a - - - ~ -> u1 A *aJ 5U -. ; 0 C 0 -052 U CLUJ 2. =- =z U Z < CY es td .- -- . U 73

The failure of earthquake failure models

Science.gov (United States)

Gomberg, J.

2001-01-01

In this study I show that simple heuristic models and numerical calculations suggest that an entire class of commonly invoked models of earthquake failure processes cannot explain triggering of seismicity by transient or "dynamic" stress changes, such as stress changes associated with passing seismic waves. The models of this class have the common feature that the physical property characterizing failure increases at an accelerating rate when a fault is loaded (stressed) at a constant rate. Examples include models that invoke rate state friction or subcritical crack growth, in which the properties characterizing failure are slip or crack length, respectively. Failure occurs when the rate at which these grow accelerates to values exceeding some critical threshold. These accelerating failure models do not predict the finite durations of dynamically triggered earthquake sequences (e.g., at aftershock or remote distances). Some of the failure models belonging to this class have been used to explain static stress triggering of aftershocks. This may imply that the physical processes underlying dynamic triggering differs or that currently applied models of static triggering require modification. If the former is the case, we might appeal to physical mechanisms relying on oscillatory deformations such as compaction of saturated fault gouge leading to pore pressure increase, or cyclic fatigue. However, if dynamic and static triggering mechanisms differ, one still needs to ask why static triggering models that neglect these dynamic mechanisms appear to explain many observations. If the static and dynamic triggering mechanisms are the same, perhaps assumptions about accelerating failure and/or that triggering advances the failure times of a population of inevitable earthquakes are incorrect.

Strategies to improve self-management in heart failure patients.

Science.gov (United States)

Toback, Mehnosh; Clark, Nancy

2017-02-01

Heart failure is one of the most common causes of hospitalization, hospital readmission and death. Patients with heart failure have many complications, with multiple co-existing diagnoses which result in polypharmacy. Following instructions provided by many physicians, medication adjustments based on changes in their symptoms are required. Behavioral adjustments concerning diet and exercise regime are recommended. Therefore, the patient plays a crucial role in the management of heart failure. To review the available studies on heart failure self-management, and investigate educational, behavioral and psychosocial strategies that plays an important role to improve patient self-management. A literature review was conducted based upon the preferred reporting items for systematic reviews and meta-analyses (PRISMA) guidance. The articles identified through an extensive search using PubMed and UpToDate from 1999 to 2016. Improved self-management will increase compliance, promote patient quality-of-life, advance clinical outcomes, reduce hospital re-admission and will decrease hospitalization costs.

Numerical simulation of damage evolution for ductile materials and mechanical properties study

Science.gov (United States)

El Amri, A.; Hanafi, I.; Haddou, M. E. Y.; Khamlichi, A.

2015-12-01

This paper presents results of a numerical modelling of ductile fracture and failure of elements made of 5182H111 aluminium alloys subjected to dynamic traction. The analysis was performed using Johnson-Cook model based on ABAQUS software. The modelling difficulty related to prediction of ductile fracture mainly arises because there is a tremendous span of length scales from the structural problem to the micro-mechanics problem governing the material separation process. This study has been used the experimental results to calibrate a simple crack propagation criteria for shell elements of which one has often been used in practical analyses. The performance of the proposed model is in general good and it is believed that the presented results and experimental-numerical calibration procedure can be of use in practical finite-element simulations.

Numerical simulation of damage evolution for ductile materials and mechanical properties study

International Nuclear Information System (INIS)

Amri, A El; Haddou, M E Y; Hanafi, I; Khamlichi, A

2015-01-01

This paper presents results of a numerical modelling of ductile fracture and failure of elements made of 5182H111 aluminium alloys subjected to dynamic traction. The analysis was performed using Johnson-Cook model based on ABAQUS software. The modelling difficulty related to prediction of ductile fracture mainly arises because there is a tremendous span of length scales from the structural problem to the micro-mechanics problem governing the material separation process. This study has been used the experimental results to calibrate a simple crack propagation criteria for shell elements of which one has often been used in practical analyses. The performance of the proposed model is in general good and it is believed that the presented results and experimental-numerical calibration procedure can be of use in practical finite-element simulations. (paper)

Failure Rate of Pediatric Dental Treatment under General Anesthesia

Directory of Open Access Journals (Sweden)

Effat Khodadadi

2018-06-01

Full Text Available Aim: To assess the failure rates of various pediatric dental treatments performed under general anesthesia (GA after six months to five years of follow-up. Design: This multicenter retrospective cohort study was performed on patients treated by five pedodontists in two private hospitals located in northern Iran during 2010–2013 and comprised 155 patients. The patients were recalled and clinically examined. During the clinical examination of the primary teeth, oral hygiene, dmft index, and failure of previous treatments was evaluated. The data were analyzed using the Chi square and regression analyses with a significance level of 0.05. Results: 114 patients (74 males and 40 females, mean age: 37.17 ± 10.75 months with 1155 primary teeth treated under GA participated in the follow-up. The overall failure rate was 6.59%. The failure rates of pulpectomy, pulopotomy, fissure sealant, stainless steel crown (SSC, amalgam, and composite fillings were 2.90%, 3.03%, 4.83%, 5.26%, 5.33%, and 9.63%, respectively. Among the confounding factors, only gender had a significant effect on the anterior composite failure rate (p = 0.029 and age had a significant effect on the failure rate of fissure sealant therapy (p = 0.015 and SSC (p = 0.018. Conclusion: The overall rate of treatment failure in pediatric patients, treated under GA, was 6.59%.

Micromechanical measurement of beating patterns in the quantum oscillatory chemical potential of InGaAs quantum wells due to spin-orbit coupling

Energy Technology Data Exchange (ETDEWEB)

Herzog, Florian, E-mail: Florian.Herzog@ph.tum.de; Wilde, Marc A., E-mail: mwilde@ph.tum.de [Lehrstuhl für Physik funktionaler Schichtsysteme, Physik Department, Technische Universität München, James-Franck-Strasse 1, D-85748 Garching b. München (Germany); Heyn, Christian [Institut für Nanostruktur- und Festkörperphysik, Universität Hamburg, Jungiusstr. 11, D-20355 Hamburg (Germany); Hardtdegen, Hilde; Schäpers, Thomas [Peter Grünberg Institut (PGI-9) and JARA-FIT Jülich-Aachen Research Alliance, Forschungszentrum Jülich, D-52425 Jülich (Germany); Grundler, Dirk [Lehrstuhl für Physik funktionaler Schichtsysteme, Physik Department, Technische Universität München, James-Franck-Strasse 1, D-85748 Garching b. München (Germany); Laboratory of Nanoscale Magnetic Materials and Magnonics (LMGN), Institute of Materials, École Polytechnique Fédérale de Lausanne, CH-1015 Lausanne (Switzerland)

2015-08-31

The quantum oscillatory magnetization M(B) and chemical potential μ(B) of a two-dimensional (2D) electron system provide important and complementary information about its ground state energy at low temperature T. We developed a technique that provides both quantities in the same cool-down process via a decoupled static operation and resonant excitation of a micromechanical cantilever. On InGaAs/InP heterostructures, we observed beating patterns in both M(B) and μ(B) attributed to spin-orbit interaction. A significantly enhanced sensitivity in μ enabled us to extract Rashba and Dresselhaus parameters with high accuracy. The technique is powerful for detailed investigations on the electronic properties of 2D materials.

Market failures and government policies in gas markets

International Nuclear Information System (INIS)

Mulder, M; Zwart, G.

2006-02-01

This memorandum analyses the fundamental characteristics of the natural gas market and its consequences for government policies. In the past, the European gas market was dominated by state-owned monopolists but since the start of the liberalisation, privatisation and re-regulation in the early 1990s, the market has fundamentally changed. Nevertheless, governments are still involved in the gas industry, not only in gas exporting countries such as Russia, but also in a country like the Netherlands where the government has imposed a cap on production from the main gas field (Groningen) as well as owns shares in the main wholesale trader (Gasunie Trade and Supply) which has the obligation to accept all gas offered by producers on the small fields. In the main report of this project we present a cost-benefit analysis of the Dutch gas-depletion policy. In this memorandum we explore the natural-gas market more broadly, looking for factors why government intervention may be needed using the welfare-economic approach according to which government intervention should be based on the presence of market failures. After a brief description of the main characteristics of the gas industry, we systematically analyse sources of market failures, such as geopolitical factors, economies of scale and externalities, and finally go into the question which policy options may be chosen to address those market failures

Influence of diabetes mellitus on heart failure risk and outcome

Directory of Open Access Journals (Sweden)

Van Belle Eric

2003-01-01

Full Text Available Abstract Our aim is to summarize and discuss the recent literature linking diabetes mellitus with heart failure, and to address the issue of the optimal treatment for diabetic patients with heart failure. The studies linking diabetes mellitus (DM with heart failure (HF The prevalence of diabetes mellitus in heart failure populations is close to 20% compared with 4 to 6% in control populations. Epidemiological studies have demonstrated an increased risk of heart failure in diabetics; moreover, in diabetic populations, poor glycemic control has been associated with an increased risk of heart failure. Various mechanisms may link diabetes mellitus to heart failure: firstly, associated comorbidities such as hypertension may play a role; secondly, diabetes accelerates the development of coronary atherosclerosis; thirdly, experimental and clinical studies support the existence of a specific diabetic cardiomyopathy related to microangiopathy, metabolic factors or myocardial fibrosis. Subgroup analyses of randomized trials demonstrate that diabetes is also an important prognostic factor in heart failure. In addition, it has been suggested that the deleterious impact of diabetes may be especially marked in patients with ischemic cardiomyopathy. Treatment of heart failure in diabetic patients The knowledge of the diabetic status may help to define the optimal therapeutic strategy for heart failure patients. Cornerstone treatments such as ACE inhibitors or beta-blockers appear to be uniformly beneficial in diabetic and non diabetic populations. However, in ischemic cardiomyopathy, the choice of the revascularization technique may differ according to diabetic status. Finally, clinical studies are needed to determine whether improved metabolic control might favorably influence the outcome of diabetic heart failure patients.

On the importance of analyzing flood defense failures

Directory of Open Access Journals (Sweden)

Özer Işıl Ece

2016-01-01

Full Text Available Flood defense failures are rare events but when they do occur lead to significant amounts of damage. The defenses are usually designed for rather low-frequency hydraulic loading and as such typically at least high enough to prevent overflow. When they fail, flood defenses like levees built with modern design codes usually either fail due to wave overtopping or geotechnical failure mechanisms such as instability or internal erosion. Subsequently geotechnical failures could trigger an overflow leading for the breach to grow in size Not only the conditions relevant for these failure mechanisms are highly uncertain, also the model uncertainty in geomechanical, internal erosion models, or breach models are high compared to other structural models. Hence, there is a need for better validation and calibration of models or, in other words, better insight in model uncertainty. As scale effects typically play an important role and full-scale testing is challenging and costly, historic flood defense failures can be used to provide insights into the real failure processes and conditions. The recently initiated SAFElevee project at Delft University of Technology aims to exploit this source of information by performing back analysis of levee failures at different level of detail. Besides detailed process based analyses, the project aims to investigate spatial and temporal patterns in deformation as a function of the hydrodynamic loading using satellite radar interferometry (i.e. PS-InSAR in order to examine its relation with levee failure mechanisms. The project aims to combine probabilistic approaches with the mechanics of the various relevant failure mechanisms to reduce model uncertainty and propose improvements to assessment and design models. This paper describes the approach of the study to levee breach analysis and the use of satellites for breach initiation analysis, both adopted within the SAFElevee project.

Genetic determinants of heart failure: facts and numbers.

Science.gov (United States)

Czepluch, Frauke S; Wollnik, Bernd; Hasenfuß, Gerd

2018-06-01

The relevance of gene mutations leading to heart diseases and hence heart failure has become evident. The risk for and the course of heart failure depends on genomic variants and mutations underlying the so-called genetic predisposition. Genetic contribution to heart failure is highly heterogenous and complex. For any patient with a likely inherited heart failure syndrome, genetic counselling is recommended and important. In the last few years, novel sequencing technologies (named next-generation sequencing - NGS) have dramatically improved the availability of molecular testing, the efficiency of genetic analyses, and moreover reduced the cost for genetic testing. Due to this development, genetic testing has become increasingly accessible and NGS-based sequencing is now applied in clinical routine diagnostics. One of the most common reasons of heart failure are cardiomyopathies such as the dilated or the hypertrophic cardiomyopathy. Nearly 100 disease-associated genes have been identified for cardiomyopathies. The knowledge of a pathogenic mutation can be used for genetic counselling, risk and prognosis determination, therapy guidance and hence for a more effective treatment. Besides, family cascade screening for a known familial, pathogenic mutation can lead to an early diagnosis in affected individuals. At that timepoint, a preventative intervention could be used to avoid or delay disease onset or delay disease progression. Understanding the cellular basis of genetic heart failure syndromes in more detail may provide new insights into the molecular biology of physiological and impaired cardiac (cell) function. As our understanding of the molecular and genetic pathophysiology of heart failure will increase, this might help to identify novel therapeutic targets and may lead to the development of new and specific treatment options in patients with heart failure. © 2018 The Authors. ESC Heart Failure published by John Wiley & Sons Ltd on behalf of the European

Relationship between age at natural menopause and risk of heart failure.

Science.gov (United States)

Rahman, Iffat; Åkesson, Agneta; Wolk, Alicja

2015-01-01

We investigated whether younger age at natural menopause confers a risk of heart failure. We also examined a possible modifying effect of tobacco smoking. This study used the population-based Swedish Mammography Cohort; 22,256 postmenopausal women with information on age at natural menopause were followed from 1997 through 2011. First event of heart failure was ascertained through the Swedish National Patient Register and the Cause of Death Register. Cox proportional hazards regression analyses were conducted to estimate multivariable-adjusted hazard ratios (HRs) and 95% CIs. During a mean follow-up of 13 years, we ascertained 2,532 first events of heart failure hospitalizations and deaths. The mean age at menopause was 51 years. Early natural menopause (40-45 y), compared with menopause at ages 50 to 54 years, was significantly associated with heart failure (HR, 1.40; 95% CI, 1.19 to 1.64). In analyses stratified by smoking status, similar HRs were observed for this age group among never smokers (HR, 1.33; 95% CI, 1.06 to 1.66) and ever smokers (HR, 1.39; 95% CI, 1.09 to 1.78). Among ever smokers, increased incidence (HR, 1.25; 95% CI, 1.06 to 1.47) of heart failure could be detected even among those who entered menopause at ages 46 to 49 years. We found a significant interaction between age at natural menopause and smoking (P = 0.019). This study indicates that women who experience early natural menopause are at increased risk for developing heart failure and that smoking can modify the association by increasing the risk even among women who enter menopause around ages 46 to 49 years.

Development of component failure data for seismic risk analysis

International Nuclear Information System (INIS)

Fray, R.R.; Moulia, T.A.

1981-01-01

This paper describes the quantification and utilization of seismic failure data used in the Diablo Canyon Seismic Risk Study. A single variable representation of earthquake severity that uses peak horizontal ground acceleration to characterize earthquake severity was employed. The use of a multiple variable representation would allow direct consideration of vertical accelerations and the spectral nature of earthquakes but would have added such complexity that the study would not have been feasible. Vertical accelerations and spectral nature were indirectly considered because component failure data were derived from design analyses, qualification tests and engineering judgment that did include such considerations. Two types of functions were used to describe component failure probabilities. Ramp functions were used for components, such as piping and structures, qualified by stress analysis. 'Anchor points' for ramp functions were selected by assuming a zero probability of failure at code allowable stress levels and unity probability of failure at ultimate stress levels. The accelerations corresponding to allowable and ultimate stress levels were determined by conservatively assuming a linear relationship between seismic stress and ground acceleration. Step functions were used for components, such as mechanical and electrical equipment, qualified by testing. Anchor points for step functions were selected by assuming a unity probability of failure above the qualification acceleration. (orig./HP)

Most likely failure location during severe accident conditions

International Nuclear Information System (INIS)

Rempe, J.L.; Allison, C.M.

1991-01-01

This paper describes preliminary results from which finite element calculation results are used in conjunction with analytical calculation results to predict failure in different LWR vessel designs during a severe accident. Detailed analyses are being performed to investigate the relative likelihood of a BWR vessel and drain line penetration to fail during a wide range of severe accident conditions. Analytically developed failure maps, which were developed in terms of dimensionless groups, are applied to consider geometries and materials occurring in other LWR vessel designs. Preliminary numerical analysis results indicate that if ceramic debris relocates within the BWR drain line to a distance below the lower head, the drain line will reach failure temperatures before the vessel fails. Application of failure maps for these debris conditions to other LWR geometries indicate that in-vessel tube melting will occur in either BWR or PWR vessel designs. Furthermore, if this melt is assumed to fill the entire penetration flow area, the melt is predicted to travel well below the lower head in any of the reference LWR penetrations. However, failure maps suggest the result that ex-vessel tube temperatures exceed the penetration's ultimate strength is specific to the BWR drain line because of its material composition and relatively large effective diameter for melt flow

Development of Circular Disk Model for Polymeric Nanocomposites and Micromechanical Analysis of Residual Stresses in Reinforced Fibers with Carbon Nanotubes

Directory of Open Access Journals (Sweden)

A. R. Ghasemi

2017-02-01

Full Text Available In this study, Circular Disk Model (CDM has been developed to determine the residual stresses in twophase and three- phase unit cell. The two-phase unit cell is consisting of carbon fiber and matrix. The three-phase unit cell is consisting of carbon fiber, carbon nanotubes and matrix in which the carbon fiber is reinforced with the carbon nanotube using electrophoresis method. For different volume fractions of carbon nanotubes, thermal properties of the carbon fiber and carbon nanotube in different linear and lateral directions and also different placement conditions of carbon nanotubes have been considered. Also, residual stresses distribution in two and three phases has been studied, separately. Results of micromechanical analysis of residual stresses obtained from Finite Element Method and CDM, confirms the evaluation and development of three dimensional CDM.

Establishment, maintenance and application of failure statistics as a basis for availability optimization

International Nuclear Information System (INIS)

Poll, H.

1989-01-01

The purpose of failure statistics is to obtain hints on weak points due to operation and design. The present failure statistics of Rheinisch-Westfaelisches Elektrizitaetswerk (RWE) is based on reducing availability of power station units. If damage or trouble occurs with a unit, data will be recorded in order to calculate the unavailability and to describe the occurence, the extent, and the removal of damage. Following a survey of the most important data, a short explanation is given on updating of failure statistics and some problems of this job are mentioned. Finally some examples are given, how failure statistics can be used for analyses. (orig.) [de

Stochastic failure modelling of unidirectional composite ply failure

International Nuclear Information System (INIS)

Whiteside, M.B.; Pinho, S.T.; Robinson, P.

2012-01-01

Stochastic failure envelopes are generated through parallelised Monte Carlo Simulation of a physically based failure criteria for unidirectional carbon fibre/epoxy matrix composite plies. Two examples are presented to demonstrate the consequence on failure prediction of both statistical interaction of failure modes and uncertainty in global misalignment. Global variance-based Sobol sensitivity indices are computed to decompose the observed variance within the stochastic failure envelopes into contributions from physical input parameters. The paper highlights a selection of the potential advantages stochastic methodologies offer over the traditional deterministic approach.

Analogy between electrochemical behaviour of thick silicon granular electrodes for lithium batteries and fine soils micromechanics

International Nuclear Information System (INIS)

Nguyen, B.P.N.; Gaubicher, J.; Lestriez, B.

2014-01-01

In this paper we study the influence of the distribution and the shape of the carbon conductive additives on the cyclability of thick silicon based composite electrodes. Results pinpoint the influence of carbon additives is not only to play on the electronic conductivity but also to play on the micromechanics (stress distribution) of the composite films. The lack of correlation between electrochemical performance and the macroscopic electronic conductivity of the pristine electrodes and the observation of repeated drops and jumps in capacity during cycling brought us to make an analogy between the silicon composite electrodes and cohesive granular materials such as fine soils media. Considering the collective mechanical behavior of a stack of silicon particles upon repeated volume variations shed a novel understanding to the electrochemical behavior of composite electrodes based on silicon and alloying materials and tells us how critically important is the design at the different scales (the particle, a few particles, the composite electrode, the cell) to engineer the mechanical stress and strain and improve cycle life

Sensitivity analyses on in-vessel hydrogen generation for KNGR

International Nuclear Information System (INIS)

Kim, See Darl; Park, S.Y.; Park, S.H.; Park, J.H.

2001-03-01

Sensitivity analyses for the in-vessel hydrogen generation, using the MELCOR program, are described in this report for the Korean Next Generation Reactor. The typical accident sequences of a station blackout and a large LOCA scenario are selected. A lower head failure model, a Zircaloy oxidation reaction model and a B 4 C reaction model are considered for the sensitivity parameters. As for the base case, 1273.15K for a failure temperature of the penetrations or the lower head, an Urbanic-Heidrich correlation for the Zircaloy oxidation reaction model and the B 4 C reaction model are used. Case 1 used 1650K as the failure temperature for the penetrations and Case 2 considered creep rupture instead of penetration failure. Case 3 used a MATPRO-EG and G correlation for the Zircaloy oxidation reaction model and Case 4 turned off the B 4 C reaction model. The results of the studies are summarized below : (1) When the penetration failure temperature is higher, or the creep rupture failure model is considered, the amount of hydrogen increases for two sequences. (2) When the MATPRO-EG and G correlation for a Zircaloy oxidation reaction is considered, the amount of hydrogen is less than the Urbanic-Heidrich correlation (Base case) for both scenarios. (3) When the B 4 C reaction model turns off, the amount of hydrogen decreases for two sequences

Main factors for fatigue failure probability of pipes subjected to fluid thermal fluctuation

International Nuclear Information System (INIS)

Machida, Hideo; Suzuki, Masaaki; Kasahara, Naoto

2015-01-01

It is very important to grasp failure probability and failure mode appropriately to carry out risk reduction measures of nuclear power plants. To clarify the important factors for failure probability and failure mode of pipes subjected to fluid thermal fluctuation, failure probability analyses were performed by changing the values of a stress range, stress ratio, stress components and threshold of stress intensity factor range. The important factors for the failure probability are range, stress ratio (mean stress condition) and threshold of stress intensity factor range. The important factor for the failure mode is a circumferential angle range of fluid thermal fluctuation. When a large fluid thermal fluctuation acts on the entire circumferential surface of the pipe, the probability of pipe breakage increases, calling for measures to prevent such a failure and reduce the risk to the plant. When the circumferential angle subjected to fluid thermal fluctuation is small, the failure mode of piping is leakage and the corrective maintenance might be applicable from the viewpoint of risk to the plant. (author)

Heat Transfer and Failure Mode Analyses of Ultrahigh-Temperature Ceramic Thermal Protection System of Hypersonic Vehicles

Directory of Open Access Journals (Sweden)

Tianbao Cheng

2014-01-01

Full Text Available The transient temperature distribution of the ultrahigh-temperature ceramic (UHTC thermal protection system (TPS of hypersonic vehicles is calculated using finite volume method. Convective cooling enables a balance of heat increment and loss to be achieved. The temperature in the UHTC plate at the balance is approximately proportional to the surface heat flux and is approximately inversely proportional to the convective heat transfer coefficient. The failure modes of the UHTCs are presented by investigating the thermal stress field of the UHTC TPS under different thermal environments. The UHTCs which act as the thermal protection materials of hypersonic vehicles can fail because of the tensile stress at the lower surface, an area above the middle plane, and the upper surface as well as because of the compressive stress at the upper surface. However, the area between the lower surface and the middle plane and a small area near the upper surface are relatively safe. Neither the compressive stress nor the tensile stress will cause failure of these areas.

Effects of intravenous home dobutamine in palliative end-stage heart failure on quality of life, heart failure hospitalization, and cost expenditure.

Science.gov (United States)

Martens, Pieter; Vercammen, Jan; Ceyssens, Wendy; Jacobs, Linda; Luwel, Evert; Van Aerde, Herwig; Potargent, Peter; Renaers, Monique; Dupont, Matthias; Mullens, Wilfried

2018-01-17

In patients with palliative end-stage heart failure, interventions that could provide symptomatic relief and prevent hospital admissions are important. Ambulatory continuous intravenous inotropes have been advocated by guidelines for such a purpose. We sought to determine the effect of intravenous dobutamine on symptomatic status, hospital stay, mortality, and cost expenditure. All consecutive end-stage heart failure patients not amenable for advanced therapies and discharged with continuous intravenous home dobutamine from a single tertiary centre between April 2011 and January 2017 were retrospectively analysed. Dobutamine (fixed dose) was infused through a single-lumen central venous catheter with a small pump that was refilled by a nurse on a daily basis. Symptomatic status was longitudinally assessed as the change in New York Heart Association class and patient global assessment scale. Antecedent and incident heart failure hospitalizations were determined in a paired fashion, and cost impact was assessed. A total of 21 patients (age 77 ± 9 years) were followed up for 869 ± 647 days. At first follow-up (6 ± 1 weeks) after the initiation of dobutamine, patients had a significant improvement in New York Heart Association class (-1.29 ± 0.64; P heart failure hospitalizations assessed at 3, 6, and 12 months were significantly reduced (P heart failure hospitalizations over the same time period. Cost expenditure was significantly lower at 3 (P heart failure is feasible and associated with improved symptomatic status, heart failure hospitalizations, and health-care-related costs. Nevertheless, results should be interpreted in the context of the small and retrospective design. Larger studies are necessary to evaluate the effect of dobutamine in palliative end-stage heart failure. © 2018 The Authors. ESC Heart Failure published by John Wiley & Sons Ltd on behalf of the European Society of Cardiology.

Predictors of sudden death and death from pump failure in congestive heart failure are different. Analysis of 24 h Holter monitoring, clinical variables, blood chemistry, exercise test and radionuclide angiography

DEFF Research Database (Denmark)

Madsen, B K; Rasmussen, Verner; Hansen, J F

1997-01-01

Association class II and 44% in III. Total mortality after 1 year was 21%, after 2 years 32%. Of 60 deaths, 33% were sudden and 49% due to pump failure. Multivariate analyses identified totally different risk factors for sudden death: ventricular tachycardia, s-sodium ....6 mmol/l, s-potassium sudden death and for death from progressive pump failure........80 mmol/l, s-creatinine > 121 mumol/l, and maximal change in heart rate during exercise death from progressive pump failure: New York Heart Association class III + IV, delta heart rate over 24 h 7...

Worsening renal function definition is insufficient for evaluating acute renal failure in acute heart failure.

Science.gov (United States)

Shirakabe, Akihiro; Hata, Noritake; Kobayashi, Nobuaki; Okazaki, Hirotake; Matsushita, Masato; Shibata, Yusaku; Nishigoori, Suguru; Uchiyama, Saori; Asai, Kuniya; Shimizu, Wataru

2018-06-01

Whether or not the definition of a worsening renal function (WRF) is adequate for the evaluation of acute renal failure in patients with acute heart failure is unclear. One thousand and eighty-three patients with acute heart failure were analysed. A WRF, indicated by a change in serum creatinine ≥0.3 mg/mL during the first 5 days, occurred in 360 patients while no-WRF, indicated by a change failure; n = 98). The patients were assigned to another set of four groups: no-WRF/no-AKI (n = 512), no-WRF/AKI (n = 211), WRF/no-AKI (n = 239), and WRF/AKI (n = 121). A multivariate logistic regression model found that no-WRF/AKI and WRF/AKI were independently associated with 365 day mortality (hazard ratio: 1.916; 95% confidence interval: 1.234-2.974 and hazard ratio: 3.622; 95% confidence interval: 2.332-5.624). Kaplan-Meier survival curves showed that the rate of any-cause death during 1 year was significantly poorer in the no-WRF/AKI and WRF/AKI groups than in the WRF/no-AKI and no-WRF/no-AKI groups and in Class I and Class F than in Class R and the no-AKI group. The presence of AKI on admission, especially Class I and Class F status, is associated with a poor prognosis despite the lack of a WRF within the first 5 days. The prognostic ability of AKI on admission may be superior to WRF within the first 5 days. © 2018 The Authors. ESC Heart Failure published by John Wiley & Sons Ltd on behalf of the European Society of Cardiology.

Prognostic value of the physical examination in patients with heart failure and atrial fibrillation: insights from the AF-CHF trial (atrial fibrillation and chronic heart failure).

Science.gov (United States)

Caldentey, Guillem; Khairy, Paul; Roy, Denis; Leduc, Hugues; Talajic, Mario; Racine, Normand; White, Michel; O'Meara, Eileen; Guertin, Marie-Claude; Rouleau, Jean L; Ducharme, Anique

2014-02-01

This study sought to assess the prognostic value of physical examination in a modern treated heart failure population. The physical examination is the cornerstone of the evaluation and monitoring of patients with heart failure. Yet, the prognostic value of congestive signs (i.e., peripheral edema, jugular venous distension, a third heart sound, and pulmonary rales) has not been assessed in the current era. A post-hoc analysis was conducted on all 1,376 patients, 81% male, mean age 67 ± 11 years, with symptomatic left ventricular systolic dysfunction enrolled in the AF-CHF (Atrial Fibrillation and Congestive Heart Failure) trial. The prognostic value of baseline physical examination findings was assessed in univariate and multivariate Cox regression analyses. Peripheral edema was observed in 425 (30.9%), jugular venous distension in 297 (21.6%), a third heart sound in 207 (15.0%), and pulmonary rales in 178 (12.9%) patients. Death from cardiovascular causes occurred in 357 (25.9%) patients over a mean follow-up of 37 ± 19 months. All 4 physical examination findings were associated with cardiovascular mortality in univariate analyses (all p values examination (i.e., peripheral edema, jugular venous distension, a third heart sound, and pulmonary rales) continue to provide important prognostic information in patients with congestive heart failure. Copyright © 2014 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

A Critical Review of Landslide Failure Mechanisms

Science.gov (United States)

Stead, D.; Wolter, A.; Clague, J. J.

2011-12-01

During the last ten years several comprehensive geotechnical studies have been completed on major historic landslides including Randa in Switzerland, Frank in Canada, Aknes in Norway, La Clapiere in France and Vaiont in Italy. In addition, numerous researchers have documented deep-seated gravitational deformations and a wide variety of large prehistoric rock slope failures. The information provided by these studies is evidence of the significant advances made in our ability to map, monitor and model landslides. Over the same period, the mining industry has developed large open pits with slope heights exceeding 1000 m that provide important analogues to high mountain slopes. In this paper we analyse data from the literature to illustrate the importance of brittle fracture, 3D controls, anisotropy, overburden stress, geomorphic processes, groundwater and temperature in major landslides and provide some indicators as to the research required to further understand the complexity of rock slope failure mechanisms. The nature of the landslide failure surface has received inadequate attention in the past, with failure surfaces typically considered in 2D and simulated as discrete, smooth and often planar features. Current work shows that failure surfaces are inherently three-dimensional and have much structural variability across the area of the landslide scarp, reflecting complex structural histories. Such anisotropy and variations may result in multiple events or distinct blocks that move at different rates. Just as most failure surfaces vary spatially, they may also change with depth and thus should more realistically be considered failure zones rather than discrete surfaces. The increasing recognition of the importance of step-path failures, internal dilation and brittle fracture are indicative of the complexity in slope failure surfaces. Related to the variation in failure surface characteristics is the importance of 3D rotational displacements and both the

Investigation of component failure rates for pulsed versus steady state tokamak operation

International Nuclear Information System (INIS)

Cadwallader, L.C.

1992-07-01

This report presents component failure rate data sources applicable to magnetic fusion systems, and defines multiplicative factors to adjust these data for specific use on magnetic fusion experiment designs. The multipliers address both long pulse and steady state tokamak operation. Thermal fatigue and radiation damage are among the leading reasons for large multiplier values in pulsed operation applications. Field failure rate values for graphite protective tiles are presented, and beryllium tile failure rates in laboratory testing are also given. All of these data can be used for reliability studies, safety analyses, design tradeoff studies, and risk assessments

Review of HEDL fuel pin transient analyses analytical programs

International Nuclear Information System (INIS)

Scott, J.H.; Baars, R.E.

1975-05-01

Methods for analysis of transient fuel pin performance are described, as represented by the steady-state SIEX code and the PECT series of codes used for steady-state and transient mechanical analyses. The empirical fuel failure correlation currently in use for analysis of transient overpower accidents is described. (U.S.)

An analysis of human maintenance failures of a nuclear power plant

International Nuclear Information System (INIS)

Pyy, P.

2000-01-01

In the report, a study of faults caused by maintenance activities is presented. The objective of the study was to draw conclusions on the unplanned effects of maintenance on nuclear power plant safety and system availability. More than 4400 maintenance history reports from the years 1992-1994 of Olkiluoto BWR nuclear power plant (NPP) were analysed together with the maintenance personnel. The human action induced faults were classified, e.g., according to their multiplicity and effects. This paper presents and discusses the results of a statistical analysis of the data. Instrumentation and electrical components appeared to be especially prone to human failures. Many human failures were found in safety related systems. Several failures also remained latent from outages to power operation. However, the safety significance of failures was generally small. Modifications were an important source of multiple human failures. Plant maintenance data is a good source of human reliability data and it should be used more in the future. (orig.)

Raman Spectroscopy Study of Annealing-Induced Effects on Graphene Prepared by Micromechanical Exfoliation

International Nuclear Information System (INIS)

Song, Ji Eun; Ko, Taeg Yeoung; Ryu, Sun Min

2010-01-01

Raman spectroscopy was combined with AFM to investigate the effects of thermal annealing on the graphene samples prepared by the widely used micromechanical exfoliation method. Following annealing cycles, adhesive residues were shown to contaminate graphene sheets with thin molecular layers in their close vicinity causing several new intense Raman bands. Detailed investigation shows that the Raman scattering is very strong and may be enhanced by the interaction with graphene. Although the current study does not pinpoint detailed origins for the new Raman bands, the presented results stress that graphene prepared by the above method may require extra cautions when treated with heat or possibly solvents. Since its isolation from graphite, graphene has drawn a lot of experimental and theoretical research. These efforts have been mostly in pursuit of various applications such as electronics, sensors, stretchable transparent electrodes, and various composite materials. To accomplish such graphene-based applications, understanding chemical interactions of this new material with environments during various processing treatments will become more important. Since thermal annealing is widely used in various research of graphene for varying purposes such as cleaning, nanostructuring, reactions, etc., understanding annealing-induced effects is prerequisite to many fundamental studies of graphene. In this regard, it is to be noted that there has been a controversy on the cause of the annealing-induced hole doping in graphene

Micromechanical contact stiffness devices and application for calibrating contact resonance atomic force microscopy

Science.gov (United States)

Rosenberger, Matthew R.; Chen, Sihan; Prater, Craig B.; King, William P.

2017-01-01

This paper reports the design, fabrication, and characterization of micromechanical devices that can present an engineered contact stiffness to an atomic force microscope (AFM) cantilever tip. These devices allow the contact stiffness between the AFM tip and a substrate to be easily and accurately measured, and can be used to calibrate the cantilever for subsequent mechanical property measurements. The contact stiffness devices are rigid copper disks of diameters 2-18 μm integrated onto a soft silicone substrate. Analytical modeling and finite element simulations predict the elastic response of the devices. Measurements of tip-sample interactions during quasi-static force measurements compare well with modeling simulation, confirming the expected elastic response of the devices, which are shown to have contact stiffness 32-156 N m-1. To demonstrate one application, we use the disk sample to calibrate three resonant modes of a U-shaped AFM cantilever actuated via Lorentz force, at approximately 220, 450, and 1200 kHz. We then use the calibrated cantilever to determine the contact stiffness and elastic modulus of three polymer samples at these modes. The overall approach allows cantilever calibration without prior knowledge of the cantilever geometry or its resonance modes, and could be broadly applied to both static and dynamic measurements that require AFM calibration against a known contact stiffness.

Micromechanical Analysis of Crack Closure Mechanism for Intelligent Material Containing TiNi Fibers

Science.gov (United States)

Araki, Shigetoshi; Ono, Hiroyuki; Saito, Kenji

In our previous study, the micromechanical modeling of an intelligent material containing TiNi fibers was performed and the stress intensity factor KI at the tip of the crack in the material was expressed in terms of the magnitude of the shape memory shrinkage of the fibers and the thermal expansion strain in the material. In this study, the value of KI at the tip of the crack in the TiNi/epoxy material is calculated numerically by using analytical expressions obtained in our first report. As a result, we find that the KI value decreases with increasing shrink strain of the fibers, and this tendency agrees with that of the experimental result obtained by Shimamoto etal.(Trans. Jpn. Soc. Mech. Eng., Vol. 65, No. 634 (1999), pp. 1282-1286). Moreover, there exists an optimal value of the shrink strain of the fibers to make the KI value zero. The change in KI with temperature during the heating process from the reference temperature to the inverse austenitic finishing temperature of TiNi fiber is also consistent with the experimental result. These results can be explained by the changes in the shrink strain, the thermal expansion strain, and the elastic moduli of TiNi fiber with temperature. These results may be useful in designing intelligent materials containing TiNi fibers from the viewpoint of crack closure.

Caffeine, cognitive failures and health in a non-working community sample.

Science.gov (United States)

Smith, Andrew P

2009-01-01

Most studies of the effects of caffeine on performance have been conducted in the laboratory and further information is required on the real-life effects of caffeine consumption on cognition. In addition, possible effects of caffeine consumption on a range of health outcomes should also be assessed in these studies to enable cost-benefit analyses to be conducted. Secondary analyses of a large epidemiological database (N = 3223 non-working participants, 57% female, with a mean age of 49.6 years, range 17-92 years) were conducted to examine associations between caffeine consumption (mean caffeine consumption was 140 mg/day, range 0-1800 mg) and cognitive failures (errors of memory, attention and action) in a non-working sample. Associations between caffeine consumption and physical and mental health problems were also examined. The study involved secondary analyses of a database formed by combining the Bristol Stress and Health at Work and Cardiff Health and Safety at Work studies. Associations between caffeine consumption and frequency of cognitive failures and health outcomes were examined in a sample of non-workers. After controlling for possible confounding factors significant associations between caffeine consumption and fewer cognitive failures were observed. Initial analyses suggested that many health variables were associated with regular level of caffeine consumption. However, most of the significant effects of caffeine disappeared when demographic and lifestyle factors were controlled for. Consumption of caffeine was, however, associated with a reduced risk of depression. These effects were also observed in separate analyses examining the source of the caffeine (coffee and tea). Overall, the results show that caffeine consumption may benefit cognitive functioning in a non-working population. This confirms earlier findings from working samples. This beneficial effect of caffeine was not associated with negative health consequences. Indeed, consumption of

Micromechanics of the human vertebral body for forward flexion.

Science.gov (United States)

Yang, Haisheng; Nawathe, Shashank; Fields, Aaron J; Keaveny, Tony M

2012-08-09

To provide mechanistic insight into the etiology of osteoporotic wedge fractures, we investigated the spatial distribution of tissue at the highest risk of initial failure within the human vertebral body for both forward flexion and uniform compression loading conditions. Micro-CT-based linear elastic finite element analysis was used to virtually load 22 human T9 vertebral bodies in either 5° of forward flexion or uniform compression; we also ran analyses replacing the simulated compliant disc (E=8 MPa) with stiff polymethylmethacrylate (PMMA, E=2500 MPa). As expected, we found that, compared to uniform compression, forward flexion increased the overall endplate axial load on the anterior half of the vertebra and shifted the spatial distribution of high-risk tissue within the vertebra towards the anterior aspect of the vertebral body. However, despite that shift, the high-risk tissue remained primarily within the central regions of the trabecular bone and endplates, and forward flexion only slightly altered the ratio of cortical-to-trabecular load sharing at the mid-vertebral level (mean±SD for n=22: 41.3±7.4% compression; 44.1±8.2% forward flexion). When the compliant disc was replaced with PMMA, the anterior shift of high-risk tissue was much more severe. We conclude that, for a compliant disc, a moderate degree of forward flexion does not appreciably alter the spatial distribution of stress within the vertebral body. Copyright © 2012 Elsevier Ltd. All rights reserved.

Fundamental issues in finite element analyses of localization of deformation

NARCIS (Netherlands)

Borst, de R.; Sluys, L.J.; Mühlhaus, H.-B.; Pamin, J.

1993-01-01

Classical continuum models, i.e. continuum models that do not incorporate an internal length scale, suffer from excessive mesh dependence when strain-softening models are used in numerical analyses and cannot reproduce the size effect commonly observed in quasi-brittle failure. In this contribution

Biochemical and neurophysiological parameters in hemodialyzed patients with chronic renal failure

NARCIS (Netherlands)

Schoots, A.C.; Vries, de P.M.J.M.; Thiemann, R.C.J.; Hazejager, W.A.; Visser, S.L.; Oe, P.L.

1989-01-01

Serum concentrations of accumulated solutes, standard clinical biochemistry, and parameters of clinical neuropathy, were determined in hemodialyzed patients with chronic renal failure. Analyses by high-performance liquid chromatography included creatinine, pseudouridine, urate, p-hydroxyhippuric

Comprehensive Deployment Method for Technical Characteristics Base on Multi-failure Modes Correlation Analysis

Science.gov (United States)

Zheng, W.; Gao, J. M.; Wang, R. X.; Chen, K.; Jiang, Y.

2017-12-01

This paper put forward a new method of technical characteristics deployment based on Reliability Function Deployment (RFD) by analysing the advantages and shortages of related research works on mechanical reliability design. The matrix decomposition structure of RFD was used to describe the correlative relation between failure mechanisms, soft failures and hard failures. By considering the correlation of multiple failure modes, the reliability loss of one failure mode to the whole part was defined, and a calculation and analysis model for reliability loss was presented. According to the reliability loss, the reliability index value of the whole part was allocated to each failure mode. On the basis of the deployment of reliability index value, the inverse reliability method was employed to acquire the values of technology characteristics. The feasibility and validity of proposed method were illustrated by a development case of machining centre’s transmission system.

Markov counting and reward processes for analysing the performance of a complex system subject to random inspections

International Nuclear Information System (INIS)

Ruiz-Castro, Juan Eloy

2016-01-01

In this paper, a discrete complex reliability system subject to internal failures and external shocks, is modelled algorithmically. Two types of internal failure are considered: repairable and non-repairable. When a repairable failure occurs, the unit goes to corrective repair. In addition, the unit is subject to external shocks that may produce an aggravation of the internal degradation level, cumulative damage or extreme failure. When a damage threshold is reached, the unit must be removed. When a non-repairable failure occurs, the device is replaced by a new, identical one. The internal performance and the external damage are partitioned in performance levels. Random inspections are carried out. When an inspection takes place, the internal performance of the system and the damage caused by external shocks are observed and if necessary the unit is sent to preventive maintenance. If the inspection observes minor state for the internal performance and/or external damage, then these states remain in memory when the unit goes to corrective or preventive maintenance. Transient and stationary analyses are performed. Markov counting and reward processes are developed in computational form to analyse the performance and profitability of the system with and without preventive maintenance. These aspects are implemented computationally with Matlab. - Highlights: • A multi-state device is modelled in an algorithmic and computational form. • The performance is partitioned in multi-states and degradation levels. • Several types of failures with repair times according to degradation levels. • Preventive maintenance as response to random inspection is introduced. • The performance-profitable is analysed through Markov counting and reward processes.

Analysis of valve failures from the NUCLARR data base

International Nuclear Information System (INIS)

Moore, L.M.

1997-11-01

The Nuclear Computerized Library for Assessing Reactor Reliability (NUCLARR) contains data on component failures with categorical and qualifying information such as component design, normal operating state, system application and safety grade information which is important to the development of risk-based component surveillance testing requirements. This report presents descriptions and results of analyses of valve component failure data and covariate information available in the document Nuclear Computerized Library for Assessing Reactor Reliability Data Manual, Part 3: Hardware Component Failure Data (NUCLARR Data Manual). Although there are substantial records on valve performance, there are many categories of the corresponding descriptors and qualifying information for which specific values are missing. Consequently, this limits the data available for analysis of covariate effects. This report presents cross tabulations by different covariate categories and limited modeling of covariate effects for data subsets with substantive non-missing covariate information

Development of an approach for the analysis of network technologies in safety related instrumentation and control systems with respect to the propagation and effect of postulated failures; Entwicklung eines Ansatzes zur Analyse der Netzwerktechnologien in sicherheitsrelevanten Leittechniksystemen hinsichtlich Verbreitung und Auswirkung postulierter Fehler

Energy Technology Data Exchange (ETDEWEB)

Herb, Joachim; Jopen, Manuela; Lindner, Falk; Piljugin, Ewgenij; Vogt, Pascal

2015-06-15

So far, safety related instrumentation and control (I and C) functions in nuclear power plants, such as controlling of safety systems, were mostly performed by conventional (analog) I and C equipment. For some years now, I and C systems and equipment in nuclear power plants worldwide, but also in Germany, are modernized by computer-based I and C systems. In signal processing of the computer-based I and C systems, modern network technologies are used both for internal and external communication, whereas the reliability and safety for information transfer and processing plays an important role. National and interna-tional operational experience shows a significant influence of communication in a net-worked I and C system on its reliability. The aim of the GRS within the project 361R01351 ''Development of an approach for an analysis of network technologies in safety related I and C systems in view of distribution and effect of postulated failures'' was to improve the expertise in the field of network communication, to investigate phenomenologically potential sources of failures and fault propagation paths (Network failures) in a generic I and C system as well as to develop methodic approaches for analyses of propagation and effect of postulated failures in typical networks. The GRS conducted extensive research in the field of ''Data communication in digital I and C systems''. In this report, the basic principles of data communication of computer-based I and C systems are presented. This includes, among other things, network topolo-gies, communication protocols and standards as well as generic failures. Additionally, the properties of different analysis methods and its applicability for reliability analyses of network communication in computer-based I and C systems are discussed. Based on state of the art evaluation, an analysis approach was developed, which takes into account the specific properties of network communication and

Neurodevelopmental and Cognitive Outcomes in Children With Intestinal Failure.

Science.gov (United States)

Chesley, Patrick M; Sanchez, Sabrina E; Melzer, Lilah; Oron, Assaf P; Horslen, Simon P; Bennett, F Curt; Javid, Patrick J

2016-07-01

Recent advances in medical and surgical management have led to improved long-term survival in children with intestinal failure. Yet, limited data exist on their neurodevelopmental and cognitive outcomes. The aim of the present study was to measure neurodevelopmental outcomes in children with intestinal failure. Children enrolled in a regional intestinal failure program underwent prospective neurodevelopmental and psychometric evaluation using a validated scoring tool. Cognitive impairment was defined as a mental developmental index Neurodevelopmental impairment was defined as cerebral palsy, visual or hearing impairment, or cognitive impairment. Univariate analyses were performed using the Wilcoxon rank-sum test. Data are presented as median (range). Fifteen children with a remnant bowel length of 18 (5-85) cm were studied at age 17 (12-67) months. Thirteen patients remained dependent on parenteral nutrition. Twelve (80%) subjects scored within the normal range on cognitive testing. Each child with cognitive impairment was noted to have additional risk factors independent of intestinal failure including cardiac arrest and extreme prematurity. On univariate analysis, cognitive impairment was associated with longer inpatient hospital stays, increased number of surgical procedures, and prematurity (P neurodevelopmental impairment. A majority of children with intestinal failure demonstrated normal neurodevelopmental and cognitive outcomes on psychometric testing. These data suggest that children with intestinal failure without significant comorbidity may be at low risk for long-term neurodevelopmental impairment.

Body Mass Index and Prostate-Specific Antigen Failure Following Brachytherapy for Localized Prostate Cancer

International Nuclear Information System (INIS)

Efstathiou, Jason A.; Skowronski, Rafi Y.; Coen, John J.; Grocela, Joseph A.; Hirsch, Ariel E.; Zietman, Anthony L.

2008-01-01

Purpose: Increasing body mass index (BMI) is associated with prostate-specific antigen (PSA) failure after radical prostatectomy and external beam radiation therapy (EBRT). We investigated whether BMI is associated with PSA failure in men treated with brachytherapy for clinically localized prostate cancer. Patients and Methods: Retrospective analyses were conducted on 374 patients undergoing brachytherapy for stage T1c-T2cNXM0 prostate cancer from 1996-2001. Forty-nine patients (13%) received supplemental EBRT and 131 (35%) received androgen deprivation therapy (ADT). Height and weight data were available for 353 (94%). Cox regression analyses were performed to evaluate the relationship between BMI and PSA failure (nadir + 2 ng/ml definition). Covariates included age, race, preimplantation PSA, Gleason score, T category, percent of prescription dose to 90% of the prostate, use of supplemental EBRT, and ADT. Results: Median age, PSA, and BMI were 66 years (range, 42-80 years), 5.7 ng/ml (range, 0.4-22.6 ng/ml), and 27.1 kg/m 2 (range, 18.2-53.6 kg/m 2 ), respectively. After a median follow-up of 6.0 years (range, 3.0-10.2 years), there were 76 PSA recurrences. The BMI was not associated with PSA failure. Six-year PSA failure rates were 30.2% for men with BMI less than 25 kg/m 2 , 19.5% for BMI of 25 or greater to less than 30 kg/m 2 , and 14.4% for BMI of 30 kg/m 2 or greater (p = 0.19). Results were similar when BMI was analyzed as a continuous variable, using alternative definitions of PSA failure, and excluding patients treated with EBRT and/or ADT. In multivariate analyses, only baseline PSA was significantly associated with shorter time to PSA failure (adjusted hazard ratio, 1.12; 95% confidence interval, 1.05-1.20; p 0.0006). Conclusions: Unlike after surgery or EBRT, BMI is not associated with PSA failure in men treated with brachytherapy for prostate cancer. This raises the possibility that brachytherapy may be a preferred treatment strategy in obese

Lessons learned from fatique failures in major FWR components

International Nuclear Information System (INIS)

Ware, A.G.; Shah, V.N.

1992-01-01

This paper evaluates the field fatigue failure experience and describes the lessons learned that can be employed in managing fatigue damage at the sites of these failures and at other susceptible sites. Fatigue damage has resulted in cracks on the inside surfaces of vessels and piping, and in some cases, through-wall cracks resulting in coolant leakage. All of the fatigue failures resulted from conditions or stressors that were not accounted for in the original design analyses. In some cases, it has proven difficult to discover fatigue cracks using conventional inservice inspection methods; several cracks were detected because of leakage. Supplementary monitoring and inspection techniques such as fatigue monitoring, acoustic emission monitoring, and time-of-flight-diffraction ultrasonic testing can be used to assist in identifying susceptible sites, estimating crack growth, and sizing existing fatigue cracks. It is important to identify the root cause of failures because once the stressors and degradation mechanisms are known, changes in operating procedures and designs can be implemented to mitigate future fatigue damage

Contraceptive failure

DEFF Research Database (Denmark)

Rasch, Vibeke

2002-01-01

Most studies focusing on contraceptive failure in relation to pregnancy have focused on contraceptive failure among women having induced abortions, thereby neglecting those women who, despite contraceptive failure, accept the pregnancy and intend to carry the fetus to term. To get a more complete...... picture of the problem of contraceptive failure, this study focuses on contraceptive failure among women with diverse pregnancy outcomes. In all, 3520 pregnant women attending Odense University Hospital were included: 373 had induced abortions, 435 had spontaneous abortions, 97 had ectopic pregnancies......, and 2614 received antenatal care. The variables studied comprise age, partner relationship, number of births, occupational and economical situation, and contraceptive use.Contraceptive failure, defined as contraceptive use (condom, diaphragm, IUD, oral contraception, or another modern method...

Effect of Nesiritide in Patients with Acute Decompensated Heart Failure

NARCIS (Netherlands)

O'Connor, C. M.; Starling, R. C.; Hernandez, A. F.; Armstrong, P. W.; Dickstein, K.; Hasselblad, V.; Heizer, G. M.; Komajda, M.; Massie, B. M.; McMurray, J. J. V.; Nieminen, M. S.; Reist, C. J.; Rouleau, J. L.; Swedberg, K.; Adams, K. F.; Anker, S. D.; Atar, D.; Battler, A.; Botero, R.; Bohidar, N. R.; Butler, J.; Clausell, N.; Corbalan, R.; Costanzo, M. R.; Dahlstrom, U.; Deckelbaum, L. I.; Diaz, R.; Dunlap, M. E.; Ezekowitz, J. A.; Feldman, D.; Felker, G. M.; Fonarow, G. C.; Gennevois, D.; Gottlieb, S. S.; Hollander, J. E.; Howlett, J. G.; Hudson, M. P.; Kociol, R. D.; Krum, H.; Laucevicius, A.; Levy, W. C.; Mendez, G. F.; Metra, M.; Mittal, S.; Oh, B. -H.; Pereira, N. L.; Ponikowski, P.; Wilson, W. H.; Tanomsup, S.; Teerlink, J. R.; Triposkiadis, F.; Troughton, R. W.; Voors, A. A.; Whellan, D. J.; Zannad, F.; Califf, R. M.; Hill, Joseph A.

2011-01-01

Background Nesiritide is approved in the United States for early relief of dyspnea in patients with acute heart failure. Previous meta-analyses have raised questions regarding renal toxicity and the mortality associated with this agent. Methods We randomly assigned 7141 patients who were

Automatic generation of 2D micromechanical finite element model of silicon–carbide/aluminum metal matrix composites: Effects of the boundary conditions

DEFF Research Database (Denmark)

Qing, Hai

2013-01-01

Two-dimensional finite element (FE) simulations of the deformation and damage evolution of Silicon–Carbide (SiC) particle reinforced aluminum alloy composite including interphase are carried out for different microstructures and particle volume fractions of the composites. A program is developed...... for the automatic generation of 2D micromechanical FE-models with randomly distributed SiC particles. In order to simulate the damage process in aluminum alloy matrix and SiC particles, a damage parameter based on the stress triaxial indicator and the maximum principal stress criterion based elastic brittle damage...... model are developed within Abaqus/Standard Subroutine USDFLD, respectively. An Abaqus/Standard Subroutine MPC, which allows defining multi-point constraints, is developed to realize the symmetric boundary condition (SBC) and periodic boundary condition (PBC). A series of computational experiments...

Stochastic-Strength-Based Damage Simulation of Ceramic Matrix Composite Laminates

Science.gov (United States)

Nemeth, Noel N.; Mital, Subodh K.; Murthy, Pappu L. N.; Bednarcyk, Brett A.; Pineda, Evan J.; Bhatt, Ramakrishna T.; Arnold, Steven M.

2016-01-01

The Finite Element Analysis-Micromechanics Analysis Code/Ceramics Analysis and Reliability Evaluation of Structures (FEAMAC/CARES) program was used to characterize and predict the progressive damage response of silicon-carbide-fiber-reinforced reaction-bonded silicon nitride matrix (SiC/RBSN) composite laminate tensile specimens. Studied were unidirectional laminates [0] (sub 8), [10] (sub 8), [45] (sub 8), and [90] (sub 8); cross-ply laminates [0 (sub 2) divided by 90 (sub 2),]s; angled-ply laminates [plus 45 (sub 2) divided by -45 (sub 2), ]s; doubled-edge-notched [0] (sub 8), laminates; and central-hole laminates. Results correlated well with the experimental data. This work was performed as a validation and benchmarking exercise of the FEAMAC/CARES program. FEAMAC/CARES simulates stochastic-based discrete-event progressive damage of ceramic matrix composite and polymer matrix composite material structures. It couples three software programs: (1) the Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC), (2) the Ceramics Analysis and Reliability Evaluation of Structures Life Prediction Program (CARES/Life), and (3) the Abaqus finite element analysis program. MAC/GMC contributes multiscale modeling capabilities and micromechanics relations to determine stresses and deformations at the microscale of the composite material repeating-unit-cell (RUC). CARES/Life contributes statistical multiaxial failure criteria that can be applied to the individual brittle-material constituents of the RUC, and Abaqus is used to model the overall composite structure. For each FEAMAC/CARES simulation trial, the stochastic nature of brittle material strength results in random, discrete damage events that incrementally progress until ultimate structural failure.

Safety systems I/C equipment reliability analyses of the Kozloduy NPP units 3 and 4

Energy Technology Data Exchange (ETDEWEB)

Halev, G; Christov, N [Risk Engineering Ltd., Sofia (Bulgaria)

1996-12-31

The purpose of the analysis is to assess the safety systems I/C equipment reliability. The assessment includes: quantification of the safety systems unavailability due to component failures; definition of the minimal cut sets leading to the analysed safety systems failure; quantification of the I/C equipment importance measures of the dominant contribution components. The safety systems I/C equipment reliability has been analysed using PSAPACK (a code for probabilistic safety assessment). Fault trees for the following safety systems of the Kozloduy-3 and Kozloduy-4 reactors have been constructed: neutron flow control equipment, reactor protection system, main coolant pumps, pressurizer safety valves `Sempell`, steam dump systems, spray system, low pressure injection system, emergency feeding water system, essential service water system. THree separate reports have been issued containing the performed analyses and results. 1 ref.

A Big Data Analysis Approach for Rail Failure Risk Assessment.

Science.gov (United States)

Jamshidi, Ali; Faghih-Roohi, Shahrzad; Hajizadeh, Siamak; Núñez, Alfredo; Babuska, Robert; Dollevoet, Rolf; Li, Zili; De Schutter, Bart

2017-08-01

Railway infrastructure monitoring is a vital task to ensure rail transportation safety. A rail failure could result in not only a considerable impact on train delays and maintenance costs, but also on safety of passengers. In this article, the aim is to assess the risk of a rail failure by analyzing a type of rail surface defect called squats that are detected automatically among the huge number of records from video cameras. We propose an image processing approach for automatic detection of squats, especially severe types that are prone to rail breaks. We measure the visual length of the squats and use them to model the failure risk. For the assessment of the rail failure risk, we estimate the probability of rail failure based on the growth of squats. Moreover, we perform severity and crack growth analyses to consider the impact of rail traffic loads on defects in three different growth scenarios. The failure risk estimations are provided for several samples of squats with different crack growth lengths on a busy rail track of the Dutch railway network. The results illustrate the practicality and efficiency of the proposed approach. © 2017 The Authors Risk Analysis published by Wiley Periodicals, Inc. on behalf of Society for Risk Analysis.

Failure mode analysis using state variables derived from fault trees with application

International Nuclear Information System (INIS)

Bartholomew, R.J.

1982-01-01

Fault Tree Analysis (FTA) is used extensively to assess both the qualitative and quantitative reliability of engineered nuclear power systems employing many subsystems and components. FTA is very useful, but the method is limited by its inability to account for failure mode rate-of-change interdependencies (coupling) of statistically independent failure modes. The state variable approach (using FTA-derived failure modes as states) overcomes these difficulties and is applied to the determination of the lifetime distribution function for a heat pipe-thermoelectric nuclear power subsystem. Analyses are made using both Monte Carlo and deterministic methods and compared with a Markov model of the same subsystem

Effectiveness and adverse events of tolvaptan in octogenarians with heart failure. Interim analyses of Samsca Post-Marketing Surveillance In Heart faiLurE (SMILE study).

Science.gov (United States)

Kinugawa, Koichiro; Inomata, Takayuki; Sato, Naoki; Yasuda, Moriyoshi; Shimakawa, Toshiyuki; Bando, Kosuke; Mizuguchi, Kazuki

2015-01-01

The vasopressin receptor 2 (V2) receptor antagonist tolvaptan is an aquaretic agent that has been found to improve symptoms in patients with congestive heart failure. In this study (SMILE study), we administered tolvaptan to patients aged ≥ 80 years with heart failure accompanied by congestive symptoms and compared its effectiveness and safety profiles in this group with those in patients effectiveness of tolvaptan in the aged patients was similar to that in U-80 patients. In the safety profile, the incidence rate of thirst was lower in the aged patients than that in U-80 patients (9.6% versus 11.6%, P = 0.0023). Furthermore, the incidence of hypernatremia, defined as ≥ 150 mEq/L in aged patients, was comparable with that in U-80 patients (2.9% versus 3.6%, respectively, P = 0.3657). Based on these findings, tolvaptan has similar effectiveness and safety profiles in aged patients compared with U-80 patients. In addition, we found that a higher starting dose of tolvaptan was markedly associated with the occurrence of hypernatremia exclusively in the aged population; therefore, we recommend that tolvaptan should be started at lower doses in aged patients.

Event group importance measures for top event frequency analyses

International Nuclear Information System (INIS)

1995-01-01

Three traditional importance measures, risk reduction, partial derivative, nd variance reduction, have been extended to permit analyses of the relative importance of groups of underlying failure rates to the frequencies of resulting top events. The partial derivative importance measure was extended by assessing the contribution of a group of events to the gradient of the top event frequency. Given the moments of the distributions that characterize the uncertainties in the underlying failure rates, the expectation values of the top event frequency, its variance, and all of the new group importance measures can be quantified exactly for two familiar cases: (1) when all underlying failure rates are presumed independent, and (2) when pairs of failure rates based on common data are treated as being equal (totally correlated). In these cases, the new importance measures, which can also be applied to assess the importance of individual events, obviate the need for Monte Carlo sampling. The event group importance measures are illustrated using a small example problem and demonstrated by applications made as part of a major reactor facility risk assessment. These illustrations and applications indicate both the utility and the versatility of the event group importance measures

Event group importance measures for top event frequency analyses

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-31

Three traditional importance measures, risk reduction, partial derivative, nd variance reduction, have been extended to permit analyses of the relative importance of groups of underlying failure rates to the frequencies of resulting top events. The partial derivative importance measure was extended by assessing the contribution of a group of events to the gradient of the top event frequency. Given the moments of the distributions that characterize the uncertainties in the underlying failure rates, the expectation values of the top event frequency, its variance, and all of the new group importance measures can be quantified exactly for two familiar cases: (1) when all underlying failure rates are presumed independent, and (2) when pairs of failure rates based on common data are treated as being equal (totally correlated). In these cases, the new importance measures, which can also be applied to assess the importance of individual events, obviate the need for Monte Carlo sampling. The event group importance measures are illustrated using a small example problem and demonstrated by applications made as part of a major reactor facility risk assessment. These illustrations and applications indicate both the utility and the versatility of the event group importance measures.

A high-quality factor of 267 000 micromechanical silicon resonator utilizing TED-free torsional vibration mode

Science.gov (United States)

Nakamura, K.; Naito, Y.; Onishi, K.; Kawakatsu, H.

2012-12-01

In industrial applications of a micromechanical silicon resonator as a physical sensor, a high-quality factor Q and a low-temperature coefficient of Q (TCQ) are required for high sensitivity in a wide temperature range. Although the newly developed thin film encapsulation technique enables a beam to operate with low viscous damping in a vacuum cavity, the Q of a flexural vibration mode is limited by thermo-elastic damping (TED). We proposed a torsional beam resonator which features both a high Q and a low TCQ because theoretically the torsional vibration mode does not suffer from TED. From experiments, Q of 267 000 and TCQ of 1.4 for the 20 MHz torsional vibration mode were observed which were superior to those of the flexural mode. The pressure of the residual gas in the cavity of only 20 pl volume, which is one of the energy loss factors limiting the Q, was successfully estimated to be 1-14 Pa. Finally, the possibilities of improving the Q and the difference of the measured TCQ from a theoretical value were discussed.

Failure rates in piping manufactured to different standards

International Nuclear Information System (INIS)

Barnes, R.W.; Cooper, G.D.

1995-11-01

Most non-nuclear process piping systems in Canada and the United States are constructed to the requirements of the piping codes of the American Society of Mechanical Engineers (ASME B31.1 and B31.3). Section III of the ASME Boiler and Pressure Vessel Code, has additional requirements for piping that are expected to provide further assurance of pressure boundary integrity. This project attempted to determine if the additional requirements of Section III were beneficial in preventing failure of the pressure boundary. The approach taken in the study was to determine the causes of failure of non-nuclear piping subjected to service similar to that experienced by piping in CANDU nuclear power plants. The study examined information on carbon steel piping systems filled with water/steam which operate up to a maximum temperature of 600 F and a maximum pressure of 1600 psi. The failure mechanisms were identified and analysed to determine whether application of the requirements of Section III would have prevented the failure. Through a process of interviews and literature search, 186 failures were identified and assembled into a reference database. Many of the records were incomplete; therefore, the reference database was trimmed to include a subset of 65 failure points supported by complete data. This subset formed the basis for this study. The results from the study of other databases assembled for similar purposes were reviewed and compared to the conclusions reached in this study. These reviews confirmed the conclusions reached in this study. (author). 48 refs., 20 tabs

Physical Exercise and Patients with Chronic Renal Failure: A Meta-Analysis.

Science.gov (United States)

Qiu, Zhenzhen; Zheng, Kai; Zhang, Haoxiang; Feng, Ji; Wang, Lizhi; Zhou, Hao

2017-01-01

Chronic renal failure is a severe clinical problem which has some significant socioeconomic impact worldwide and hemodialysis is an important way to maintain patients' health state, but it seems difficult to get better in short time. Considering these, the aim in our research is to update and evaluate the effects of exercise on the health of patients with chronic renal failure. The databases were used to search for the relevant studies in English or Chinese. And the association between physical exercise and health state of patients with chronic renal failure has been investigated. Random-effect model was used to compare the physical function and capacity in exercise and control groups. Exercise is helpful in ameliorating the situation of blood pressure in patients with renal failure and significantly reduces VO 2 in patients with renal failure. The results of subgroup analyses show that, in the age >50, physical activity can significantly reduce blood pressure in patients with renal failure. The activity program containing warm-up, strength, and aerobic exercises has benefits in blood pressure among sick people and improves their maximal oxygen consumption level. These can help patients in physical function and aerobic capacity and may give them further benefits.

Micromechanisms of Crack Growth in Ceramics and Glasses in Corrosive Environments.

Science.gov (United States)

1980-05-01

Resistance Mecanique du Verre et les Moyens de l’Amelioree, Union Scientifique Continentale du Verre , Charleroix, Belgium, (1962). 8. B. A. Proctor, I...exhibit similar types of delayed failure curves. Failure occurs most rapidly at high loads. Below a critical value of the load known as the stress...fracture for the three types of materials differ greatly. Polymers and metals have plastic zones at their crack tips, so that stress corrosion

Comparison of elastic and inelastic analyses

International Nuclear Information System (INIS)

Ammerman, D.J.; Heinstein, M.W.; Wellman, G.W.

1992-01-01

The use of inelastic analysis methods instead of the traditional elastic analysis methods in the design of radioactive material (RAM) transport packagings leads to a better understanding of the response of the package to mechanical loadings. Thus, better assessment of the containment, thermal protection, and shielding integrity of the package after a structure accident event can be made. A more accurate prediction of the package response can lead to enhanced safety and also allow for a more efficient use of materials, possibly leading to a package with higher capacity or lower weight. This paper discusses the advantages and disadvantages of using inelastic analysis in the design of RAM shipping packages. The use of inelastic analysis presents several problems to the package designer. When using inelastic analysis the entire nonlinear response of the material must be known, including the effects of temperature changes and strain rate. Another problem is that there currently is not an acceptance criteria for this type of analysis that is approved by regulatory agencies. Inelastic analysis acceptance criteria based on failure stress, failure strain , or plastic energy density could be developed. For both elastic and inelastic analyses it is also important to include other sources of stress in the analyses, such as fabrication stresses, thermal stresses, stresses from bolt preloading, and contact stresses at material interfaces. Offsetting these added difficulties is the improved knowledge of the package behavior. This allows for incorporation of a more uniform margin of safety, which can result in weight savings and a higher level of confidence in the post-accident configuration of the package. In this paper, comparisons between elastic and inelastic analyses are made for a simple ring structure and for a package to transport a large quantity of RAM by rail (rail cask) with lead gamma shielding to illustrate the differences in the two analysis techniques

Internal Progressive Failure in Deep-Seated Landslides

Science.gov (United States)

Yerro, Alba; Pinyol, Núria M.; Alonso, Eduardo E.

2016-06-01

Except for simple sliding motions, the stability of a slope does not depend only on the resistance of the basal failure surface. It is affected by the internal distortion of the moving mass, which plays an important role on the stability and post-failure behaviour of a landslide. The paper examines the stability conditions and the post-failure behaviour of a compound landslide whose geometry is inspired by one of the representative cross-sections of Vajont landslide. The brittleness of the mobilized rock mass was described by a strain-softening Mohr-Coulomb model, whose parameters were derived from previous contributions. The analysis was performed by means of a MPM computer code, which is capable of modelling the whole instability procedure in a unified calculation. The gravity action has been applied to initialize the stress state. This step mobilizes part of the strength along a shearing band located just above the kink of the basal surface, leading to the formation a kinematically admissible mechanism. The overall instability is triggered by an increase of water level. The increase of pore water pressures reduces the effective stresses within the slope and it leads to a progressive failure mechanism developing along an internal shearing band which controls the stability of the compound slope. The effect of the basal shearing resistance has been analysed during the post-failure stage. If no shearing strength is considered (as predicted by a thermal pressurization analysis), the model predicts a response similar to actual observations, namely a maximum sliding velocity of 25 m/s and a run-out close to 500 m.

A Bivariate return period for levee failure monitoring

Science.gov (United States)

Isola, M.; Caporali, E.

2017-12-01

Levee breaches are strongly linked with the interaction processes among water, soil and structure, thus many are the factors that affect the breach development. One of the main is the hydraulic load, characterized by intensity and duration, i.e. by the flood event hydrograph. On the magnitude of the hydraulic load is based the levee design, generally without considering the fatigue failure due to the load duration. Moreover, many are the cases in which the levee breach are characterized by flood of magnitude lower than the design one. In order to implement the strategies of flood risk management, we built here a procedure based on a multivariate statistical analysis of flood peak and volume together with the analysis of the past levee failure events. Particularly, in order to define the probability of occurrence of the hydraulic load on a levee, a bivariate copula model is used to obtain the bivariate joint distribution of flood peak and volume. Flood peak is the expression of the load magnitude, while the volume is the expression of the stress over time. We consider the annual flood peak and the relative volume. The volume is given by the hydrograph area between the beginning and the end of event. The beginning of the event is identified as an abrupt rise of the discharge by more than 20%. The end is identified as the point from which the receding limb is characterized by the baseflow, using a nonlinear reservoir algorithm as baseflow separation technique. By this, with the aim to define warning thresholds we consider the past levee failure events and the relative bivariate return period (BTr) compared with the estimation of a traditional univariate model. The discharge data of 30 hydrometric stations of Arno River in Tuscany, Italy, in the period 1995-2016 are analysed. The database of levee failure events, considering for each event the location as well as the failure mode, is also created. The events were registered in the period 2000-2014 by EEA

Plan on test to failure of a prestressed concrete containment vessel model

International Nuclear Information System (INIS)

Takumi, K.; Nonaka, A.; Umeki, K.; Nagata, K.; Soejima, M.; Yamaura, Y.; Costello, J.F.; Riesemann, W.A. von.; Parks, M.B.; Horschel, D.S.

1992-01-01

A summary of the plans to test a prestressed concrete containment vessel (PCCV) model to failure is provided in this paper. The test will be conducted as a part of a joint research program between the Nuclear Power Engineering Corporation (NUPEC), the United States Nuclear Regulatory Commission (NRC), and Sandia National Laboratories (SNL). The containment model will be a scaled representation of a PCCV for a pressurized water reactor (PWR). During the test, the model will be slowly pressurized internally until failure of the containment pressure boundary occurs. The objectives of the test are to measure the failure pressure, to observe the mode of failure, and to record the containment structural response up to failure. Pre- and posttest analyses will be conducted to forecast and evaluate the test results. Based on these results, a validated method for evaluating the structural behavior of an actual PWR PCCV will be developed. The concepts to design the PCCV model are also described in the paper

A numerical study of the influence of microvoids in the transverse mechanical response of unidirectional composites

DEFF Research Database (Denmark)

Ashouri Vajari, Danial; González, Carlos; Llorca, Javier

2014-01-01

The effect of porosity on the transverse mechanical properties of unidirectional fiber-reinforced composites is studied by means of computational micromechanics. The composite behavior is simulated by the finite element analysis of a representative volume element of the composite microstructure...... that porosity (in the range 1-5%) led to a large reduction in the transverse strength and the influence of both types of voids in the onset and propagation of damage throughout the microstructure was studied under transverse tension and compression. Finally, the failure locus of the composite lamina under...... transverse tension/compression and out-of-plane shear was obtained by means of computational micromechanics and compared with the predictions of Puck's model and with experimental data available in the literature. The results show that the strength of composites is significantly reduced by the presence...

Failure analysis of a Francis turbine runner

Energy Technology Data Exchange (ETDEWEB)

Frunzaverde, D; Campian, V [Research Center in Hydraulics, Automation and Heat Transfer, ' Eftimie Murgu' University of Resita P-ta Traian Vuia 1-4, RO-320085, Resita (Romania); Muntean, S [Centre of Advanced Research in Engineering Sciences, Romanian Academy - Timisoara Branch Bv. Mihai Viteazu 24, RO-300223, Timisoara (Romania); Marginean, G [University of Applied Sciences Gelsenkirchen, Neidenburger Str. 10, 45877 Gelsenkirchen (Germany); Marsavina, L [Department of Strength, ' Politehnica' University of Timisoara, Bv. Mihai Viteazu 1, RO-300222, Timisoara (Romania); Terzi, R; Serban, V, E-mail: gabriela.marginean@fh-gelsenkirchen.d, E-mail: d.frunzaverde@uem.r [Ramnicu Valcea Subsidiary, S.C. Hidroelectrica S.A., Str. Decebal 11, RO-240255, Ramnicu Valcea (Romania)

2010-08-15

The variable demand on the energy market requires great flexibility in operating hydraulic turbines. Therefore, turbines are frequently operated over an extended range of regimes. Francis turbines operating at partial load present pressure fluctuations due to the vortex rope in the draft tube cone. This phenomenon generates strong vibrations and noise that may produce failures on the mechanical elements of the machine. This paper presents the failure analysis of a broken Francis turbine runner blade. The failure appeared some months after the welding repair work realized in situ on fatigue cracks initiated near to the trailing edge at the junction with the crown, where stress concentration occurs. In order to determine the causes that led to the fracture of the runner blade, the metallographic investigations on a sample obtained from the blade is carried out. The metallographic investigations included macroscopic and microscopic examinations, both performed with light and scanning electron microscopy, as well as EDX - analyses. These investigations led to the conclusion, that the cracking of the blade was caused by fatigue, initiated by the surface unevenness of the welding seam. The failure was accelerated by the hydrogen embrittlement of the filling material, which appeared as a consequence of improper welding conditions. In addition to the metallographic investigations, numerical computations with finite element analysis are performed in order to evaluate the deformation and stress distribution on blade.

Failure analysis of a Francis turbine runner

International Nuclear Information System (INIS)

Frunzaverde, D; Campian, V; Muntean, S; Marginean, G; Marsavina, L; Terzi, R; Serban, V

2010-01-01

The variable demand on the energy market requires great flexibility in operating hydraulic turbines. Therefore, turbines are frequently operated over an extended range of regimes. Francis turbines operating at partial load present pressure fluctuations due to the vortex rope in the draft tube cone. This phenomenon generates strong vibrations and noise that may produce failures on the mechanical elements of the machine. This paper presents the failure analysis of a broken Francis turbine runner blade. The failure appeared some months after the welding repair work realized in situ on fatigue cracks initiated near to the trailing edge at the junction with the crown, where stress concentration occurs. In order to determine the causes that led to the fracture of the runner blade, the metallographic investigations on a sample obtained from the blade is carried out. The metallographic investigations included macroscopic and microscopic examinations, both performed with light and scanning electron microscopy, as well as EDX - analyses. These investigations led to the conclusion, that the cracking of the blade was caused by fatigue, initiated by the surface unevenness of the welding seam. The failure was accelerated by the hydrogen embrittlement of the filling material, which appeared as a consequence of improper welding conditions. In addition to the metallographic investigations, numerical computations with finite element analysis are performed in order to evaluate the deformation and stress distribution on blade.

Failure pressure of straight pipe with wall thinning under internal pressure

International Nuclear Information System (INIS)

Kamaya, Masayuki; Suzuki, Tomohisa; Meshii, Toshiyuki

2008-01-01

The failure pressure of pipe with wall thinning was investigated by using three-dimensional elastic-plastic finite element analyses (FEA). With careful modeling of the pipe and flaw geometry in addition to a proper stress-strain relation of the material, FEA could estimate the precise burst pressure obtained by the tests. FEA was conducted by assuming three kinds of materials: line pipe steel, carbon steel, and stainless steel. The failure pressure obtained using line pipe steel was the lowest under the same flaw size condition, when the failure pressure was normalized by the value of unflawed pipe defined using the flow stress. On the other hand, when the failure pressure was normalized by the results of FEA obtained for unflawed pipe under various flaw and pipe configurations, the failure pressures of carbon steel and line pipe steel were almost the same and lower than that of stainless steel. This suggests that the existing assessment criteria developed for line pipe steel can be applied to make a conservative assessment of carbon steel and stainless steel

Mechanical properties of Y2O3-doped W-Ti alloys

International Nuclear Information System (INIS)

Aguirre, M.V.; Martin, A.; Pastor, J.Y.; LLorca, J.; Monge, M.A.; Pareja, R.

2010-01-01

W and W alloys are currently considered promising candidates for plasma facing components in future fusion reactors but most of the information on their mechanical properties at elevated temperature was obtained in the 1960s and 1970s. In this investigation, the strength and toughness of novel Y 2 O 3 -doped W-Ti alloys manufactured by powder metallurgy were measured from 25 o C up to 1000 o C in laboratory air and the corresponding deformation and failure micromechanisms were ascertained from analyses of the fracture surfaces. Although the materials were fairly brittle at ambient temperature, the strength and toughness increased with temperature and Ti content up to 600 o C. Beyond this temperature, oxidation impaired the mechanical properties but the presence of Y 2 O 3 enhanced the strength and toughness retention up to 800 o C.

Common mode failures in redundancy systems

International Nuclear Information System (INIS)

Watson, I.A.; Edwards, G.T.

1978-01-01

Difficulties are experienced in assessing the impact of common mode failures on the reliability of safety systems. The paper first covers the investigation, definition and classification of CMF based on an extensive study of the nature of CMF. This is used as a basis for analysing data from nuclear reactor safety systems and aircraft systems. Design and maintenance errors are shown to be the prdominant cause of CMF. The analysis has laid the grounds for work on relating CMF modelling and defences. (author)

Levee reliability analyses for various flood return periods - a case study in southern Taiwan

Science.gov (United States)

Huang, W.-C.; Yu, H.-W.; Weng, M.-C.

2015-04-01

In recent years, heavy rainfall conditions have caused disasters around the world. To prevent losses by floods, levees have often been constructed in inundation-prone areas. This study performed reliability analyses for the Chiuliao First Levee in southern Taiwan. The failure-related parameters were the water level, the scouring depth, and the in situ friction angle. Three major failure mechanisms were considered: the slope sliding failure of the levee and the sliding and overturning failures of the retaining wall. When the variability of the in situ friction angle and the scouring depth are considered for various flood return periods, the variations of the factor of safety for the different failure mechanisms show that the retaining wall sliding and overturning failures are more sensitive to the change of the friction angle. When the flood return period is greater than 2 years, the levee could fail with slope sliding for all values of the water level difference. The results of levee stability analysis considering the variability of different parameters could aid engineers in designing the levee cross sections, especially with potential failure mechanisms in mind.

Mineral and water content of A. gigas scales determine local micromechanical properties and energy dissipation mechanisms

Science.gov (United States)

Troncoso, Omar P.; Gigos, Florian; Torres, Fernando G.

2017-11-01

Arapaima gigas scales are natural laminated composite materials made of individual layers with different degrees of mineralization, accompanied of varying mechanical properties. This natural design provides scales with hardness and flexibility, and can serve as a source of inspiration for the development of new layered composites with a hard surface and flexible base. In this paper, we have carried out cyclic micro-indentation tests on both; the internal and the highly mineralized external surface of air dried and wet scales, in order to assess the variation of their local micromechanical properties with regard to the mineral and water content. The load-penetration (P-h) curves showed that creep takes place throughout the application of a constant force during the micro-indentation tests, confirming the time dependent response of A. gigas scales. A model that accounted for the elastic, plastic and viscous responses of the samples was used to fit the experimental results. The penetration depth during loading and creep, as well as the energy dissipated are dependent on the water content. The used model suggests that the viscous response of the internal layer increases with the water content.

Melt quality induced failure of electrical conductor (EC grade aluminum wires

Directory of Open Access Journals (Sweden)

Khaliq A.

2017-01-01

Full Text Available The failure of electrical conductor grade (EC aluminum during wire drawing process was investigated. The fractured aluminum wires were subjected to Scanning Electron Microscopy (SEM and Energy Dispersive X-ray (EDX analyses for an initial examination. Thermodynamic analyses of molten aluminum interaction with refractories was also carried out using FactSage at 710°C to predict the stable phases. The SEM/EDX analyses has revealed the inclusions in aluminum matrix. The typical inclusions observed were Al2O3, Al3C4 (Al-Carbide and oxides of refractories elements (Al, Mg, Si and O that have particle size ranging up to 5 μm. The transition metal boride particles were not identified during SEM/EDX analyses these might be too fine to be detected with this microscope. The overall investigation suggested that the possible cause of this failure is second phase particles presence as inclusions in the aluminum matrix, and this was associated with the poor quality of melt. During wire drawing process, these inclusions were pulled out of the aluminum matrix by the wiredrawing forces to produce micro-voids which led to ductile tearing and final fracture of wires. It was recommended to use ceramic foam filters to segregate inclusions from molten aluminum.

Modelling of Diffuse Failure and Fluidization in geo materials and Geo structures

International Nuclear Information System (INIS)

Pastor, M.

2013-01-01

Failure of geo structures is caused by changes in effective stresses induced by external loads (earthquakes, for instance), change in the pore pressures (rain), in the geometry (erosion), or in materials properties (chemical attack, degradation, weathering). Landslides can by analysed as the failure of a geo structure, the slope. There exist many alternative classifications of landslides can be analyzed as the failure of a geo structure, the slope. There exist many alternative classifications of landslides, but we will consider here a simple classification into slides and flows. In the case of slides, the failure consists on the movement of a part of the slope with deformations which concentrate in a narrow zone, the failure surface. This can be idealized as localized failure, and it is typical of over consolidated or dense materials exhibiting softening. On the other hand, flows are made of fluidized materials, flowing in a fluid like manner. This mechanism of failure is known as diffuse failure, and has received much less attention by researchers. Modelling of diffuse failure of slopes is complex, because there appear difficulties in the mathematical, constitutive and numerical models, which have to account for a phase transition. This work deals with modeling, and we will present here some tools recently developed by the author and the group to which he belongs. (Author)

SU-F-T-246: Evaluation of Healthcare Failure Mode And Effect Analysis For Risk Assessment

International Nuclear Information System (INIS)

Harry, T; Manger, R; Cervino, L; Pawlicki, T

2016-01-01

Purpose: To evaluate the differences between the Veteran Affairs Healthcare Failure Modes and Effect Analysis (HFMEA) and the AAPM Task Group 100 Failure and Effect Analysis (FMEA) risk assessment techniques in the setting of a stereotactic radiosurgery (SRS) procedure were compared respectively. Understanding the differences in the techniques methodologies and outcomes will provide further insight into the applicability and utility of risk assessments exercises in radiation therapy. Methods: HFMEA risk assessment analysis was performed on a stereotactic radiosurgery procedure. A previous study from our institution completed a FMEA of our SRS procedure and the process map generated from this work was used for the HFMEA. The process of performing the HFMEA scoring was analyzed, and the results from both analyses were compared. Results: The key differences between the two risk assessments are the scoring criteria for failure modes and identifying critical failure modes for potential hazards. The general consensus among the team performing the analyses was that scoring for the HFMEA was simpler and more intuitive then the FMEA. The FMEA identified 25 critical failure modes while the HFMEA identified 39. Seven of the FMEA critical failure modes were not identified by the HFMEA and 21 of the HFMEA critical failure modes were not identified by the FMEA. HFMEA as described by the Veteran Affairs provides guidelines on which failure modes to address first. Conclusion: HFMEA is a more efficient model for identifying gross risks in a process than FMEA. Clinics with minimal staff, time and resources can benefit from this type of risk assessment to eliminate or mitigate high risk hazards with nominal effort. FMEA can provide more in depth details but at the cost of elevated effort.

SU-F-T-246: Evaluation of Healthcare Failure Mode And Effect Analysis For Risk Assessment

Energy Technology Data Exchange (ETDEWEB)

Harry, T [Oregon State University, Corvallis, OR (United States); University of California, San Diego, La Jolla, CA (United States); Manger, R; Cervino, L; Pawlicki, T [University of California, San Diego, La Jolla, CA (United States)

2016-06-15

Purpose: To evaluate the differences between the Veteran Affairs Healthcare Failure Modes and Effect Analysis (HFMEA) and the AAPM Task Group 100 Failure and Effect Analysis (FMEA) risk assessment techniques in the setting of a stereotactic radiosurgery (SRS) procedure were compared respectively. Understanding the differences in the techniques methodologies and outcomes will provide further insight into the applicability and utility of risk assessments exercises in radiation therapy. Methods: HFMEA risk assessment analysis was performed on a stereotactic radiosurgery procedure. A previous study from our institution completed a FMEA of our SRS procedure and the process map generated from this work was used for the HFMEA. The process of performing the HFMEA scoring was analyzed, and the results from both analyses were compared. Results: The key differences between the two risk assessments are the scoring criteria for failure modes and identifying critical failure modes for potential hazards. The general consensus among the team performing the analyses was that scoring for the HFMEA was simpler and more intuitive then the FMEA. The FMEA identified 25 critical failure modes while the HFMEA identified 39. Seven of the FMEA critical failure modes were not identified by the HFMEA and 21 of the HFMEA critical failure modes were not identified by the FMEA. HFMEA as described by the Veteran Affairs provides guidelines on which failure modes to address first. Conclusion: HFMEA is a more efficient model for identifying gross risks in a process than FMEA. Clinics with minimal staff, time and resources can benefit from this type of risk assessment to eliminate or mitigate high risk hazards with nominal effort. FMEA can provide more in depth details but at the cost of elevated effort.

Structural failure modes in vertical tanks: reinforcement evaluation and solutions

International Nuclear Information System (INIS)

Alcantud Abellan, M.; Orden Martinez, A.

1995-01-01

Vertical storage tanks are essential components in the safety of nuclear plant systems. It has been shown that the traditional method of analysing seismic loads is not conservative, as it does not take account of the interaction between fluid and tank structure. This paper identifies different possible structural failure modes in tanks due to seismic load, and methods devised by various authors to evaluate tank structure capacity under different failure modes. These methods are based on experimental data relating to the structural behaviour of tanks during actual seismic events, tests, and theoretical analyses. The paper describes the problems of these structures under seismic loads in nuclear plants. It proposes solutions to the main structural problem, tank anchorage, for which the re-evaluation of the anchorage capacity is required, using methods (finite element) less conservative than those proposed by other authors. Also proposed is the local reinforcement of anchorages to increase their capacity. (Author) 4 refs

Characterizing the lung tissue mechanical properties using a micromechanical model of alveolar sac

Science.gov (United States)

Karami, Elham; Seify, Behzad; Moghadas, Hadi; Sabsalinejad, Masoomeh; Lee, Ting-Yim; Samani, Abbas

2017-03-01

According to statistics, lung disease is among the leading causes of death worldwide. As such, many research groups are developing powerful tools for understanding, diagnosis and treatment of various lung diseases. Recently, biomechanical modeling has emerged as an effective tool for better understanding of human physiology, disease diagnosis and computer assisted medical intervention. Mechanical properties of lung tissue are important requirements for methods developed for lung disease diagnosis and medical intervention. As such, the main objective of this study is to develop an effective tool for estimating the mechanical properties of normal and pathological lung parenchyma tissue based on its microstructure. For this purpose, a micromechanical model of the lung tissue was developed using finite element (FE) method, and the model was demonstrated to have application in estimating the mechanical properties of lung alveolar wall. The proposed model was developed by assembling truncated octahedron tissue units resembling the alveoli. A compression test was simulated using finite element method on the created geometry and the hyper-elastic parameters of the alveoli wall were calculated using reported alveolar wall stress-strain data and an inverse optimization framework. Preliminary results indicate that the proposed model can be potentially used to reconstruct microstructural images of lung tissue using macro-scale tissue response for normal and different pathological conditions. Such images can be used for effective diagnosis of lung diseases such as Chronic Obstructive Pulmonary Disease (COPD).

Zero tolerance for failure. An AREVA initiative to improve reliability

International Nuclear Information System (INIS)

Lippert, Hans-Joachim; Gentet, Guy; Mollard, Pierre; Garner, Norman

2010-01-01

Significant improvements in fuel reliability have been realized over the past 2 decades, but total elimination of failures has remained elusive. Driving reliability to higher levels requires a philosophy that does not accept that even infrequent and isolated failures are inevitable - it was on this foundation that Areva's Zero Tolerance for Failure (ZTF) initiative was established. This is not in itself either a program or project, but a fundamental shift in the way of thinking about work according to the following four principles: - Failures are avoidable, - Zero failures are our goal, - We will respond rapidly to any failure, - We succeed when we fix failures in a way that precludes recurrence. The shift to a ZTF philosophy is a broad change in corporate culture that expands the concept of failure far beyond cases where fuel rod cladding integrity is breached. While this paper specifically illustrates the ways in which ZTF has shaped the company's response to enhancing fuel rod reliability, ZTF extends to any failures of fuel products to deliver expected levels of performance, manufacturing processes to meet specifications and high first-pass acceptance criteria, and beyond to error-free performance of engineering analyses and cycle design and licensing services. Application of ZTF to enhancing fuel reliability deploys efforts in the areas of manufacturing, human factors, design, R and D, processes and product strategy. In order to achieve the necessary improvements, a number of important actions have been initiated across regions and facilities. In addition to these global scale projects and measures, each region contributes by adopting measures which are relevant to its particular activities and market needs. (orig.)

Failure Mode and Effect Analysis for remote handling transfer systems of ITER

International Nuclear Information System (INIS)

Pinna, T.; Caporali, R.; Tesini, A.

2008-01-01

A Failure Mode and Effect Analysis (FMEA) at component level was done to study safety-relevant implications arising from possible failures in performing remote handling (RH) operations at ITER facility . Autonomous air cushion transporter, pallet, sealed casks and tractor movers needed for port plug mounting/dismantling operation were analysed. For each sub-system, the breakdown of significant components was outlined and, for each component, possible failure modes have been investigated pointing out possible causes, possible actions to prevent the causes, consequences and actions to prevent or mitigate consequences. Off-normal events which may result in hazardous consequences to the public and the environment have been defined as Postulated Initiating Events (PIEs). Two safety-relevant PIEs have been defined by assessing elementary failures related to the analysed system. Each PIE has been discussed in order to qualitatively identify accident sequences arising from each of them. As an output of this FMEA study, possible incidental scenarios, where the intervention of rescue RH equipments is required to overcome critical situations determined by fault of RH components, were defined as well. Being rescue scenarios of main concern for ITER remote handling activities, such families could be helpful in defining the design requirements of port handling systems in general and on RH transfer system in particular. Furthermore, they could be useful in defining casks and vehicles to be used for rescue activities

Finite element analyses of a linear-accelerator electron gun

Science.gov (United States)

Iqbal, M.; Wasy, A.; Islam, G. U.; Zhou, Z.

2014-02-01

Thermo-structural analyses of the Beijing Electron-Positron Collider (BEPCII) linear-accelerator, electron gun, were performed for the gun operating with the cathode at 1000 °C. The gun was modeled in computer aided three-dimensional interactive application for finite element analyses through ANSYS workbench. This was followed by simulations using the SLAC electron beam trajectory program EGUN for beam optics analyses. The simulations were compared with experimental results of the assembly to verify its beam parameters under the same boundary conditions. Simulation and test results were found to be in good agreement and hence confirmed the design parameters under the defined operating temperature. The gun is operating continuously since commissioning without any thermal induced failures for the BEPCII linear accelerator.

Finite element analyses of a linear-accelerator electron gun

Energy Technology Data Exchange (ETDEWEB)

Iqbal, M., E-mail: muniqbal.chep@pu.edu.pk, E-mail: muniqbal@ihep.ac.cn [Centre for High Energy Physics, University of the Punjab, Lahore 45590 (Pakistan); Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); Wasy, A. [Department of Mechanical Engineering, Changwon National University, Changwon 641773 (Korea, Republic of); Islam, G. U. [Centre for High Energy Physics, University of the Punjab, Lahore 45590 (Pakistan); Zhou, Z. [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China)

2014-02-15

Thermo-structural analyses of the Beijing Electron-Positron Collider (BEPCII) linear-accelerator, electron gun, were performed for the gun operating with the cathode at 1000 °C. The gun was modeled in computer aided three-dimensional interactive application for finite element analyses through ANSYS workbench. This was followed by simulations using the SLAC electron beam trajectory program EGUN for beam optics analyses. The simulations were compared with experimental results of the assembly to verify its beam parameters under the same boundary conditions. Simulation and test results were found to be in good agreement and hence confirmed the design parameters under the defined operating temperature. The gun is operating continuously since commissioning without any thermal induced failures for the BEPCII linear accelerator.

Finite element analyses of a linear-accelerator electron gun

International Nuclear Information System (INIS)

Iqbal, M.; Wasy, A.; Islam, G. U.; Zhou, Z.

2014-01-01

Thermo-structural analyses of the Beijing Electron-Positron Collider (BEPCII) linear-accelerator, electron gun, were performed for the gun operating with the cathode at 1000 °C. The gun was modeled in computer aided three-dimensional interactive application for finite element analyses through ANSYS workbench. This was followed by simulations using the SLAC electron beam trajectory program EGUN for beam optics analyses. The simulations were compared with experimental results of the assembly to verify its beam parameters under the same boundary conditions. Simulation and test results were found to be in good agreement and hence confirmed the design parameters under the defined operating temperature. The gun is operating continuously since commissioning without any thermal induced failures for the BEPCII linear accelerator

Effect of a certain class of potential common mode failures on the reliability of redundant systems

International Nuclear Information System (INIS)

Apostolakis, G.E.

1975-11-01

This is a theoretical investigation of the importance of common mode failures on the reliability of redundant systems. These failures are assumed to be the result of fatal shocks (e.g., from earthquakes, explosions, etc.) which occur at a constant rate. This formulation makes it possible to predict analytically results obtained in the past which showed that the probability of a common mode failure of the redundant channels of the protection system of a typical nuclear power plant was orders of magnitude larger than the probability of failure from chance failures alone. Furthermore, since most reliability analyses of redundant systems do not include potential common mode failures in the probabilistic calculations, criteria are established which can be used to decide either that the common-mode-failure effects are indeed insignificant or that such calculations are meaningless, and more sophisticated methods of analysis are required, because common mode failures cannot be ignored

Heart Failure

Science.gov (United States)

Heart failure is a condition in which the heart can't pump enough blood to meet the body's needs. Heart failure does not mean that your heart has stopped ... and shortness of breath Common causes of heart failure are coronary artery disease, high blood pressure and ...

Self-induced parametric amplification arising from nonlinear elastic coupling in a micromechanical resonating disk gyroscope.

Science.gov (United States)

Nitzan, Sarah H; Zega, Valentina; Li, Mo; Ahn, Chae H; Corigliano, Alberto; Kenny, Thomas W; Horsley, David A

2015-03-12

Parametric amplification, resulting from intentionally varying a parameter in a resonator at twice its resonant frequency, has been successfully employed to increase the sensitivity of many micro- and nano-scale sensors. Here, we introduce the concept of self-induced parametric amplification, which arises naturally from nonlinear elastic coupling between the degenerate vibration modes in a micromechanical disk-resonator, and is not externally applied. The device functions as a gyroscope wherein angular rotation is detected from Coriolis coupling of elastic vibration energy from a driven vibration mode into a second degenerate sensing mode. While nonlinear elasticity in silicon resonators is extremely weak, in this high quality-factor device, ppm-level nonlinear elastic effects result in an order-of-magnitude increase in the observed sensitivity to Coriolis force relative to linear theory. Perfect degeneracy of the primary and secondary vibration modes is achieved through electrostatic frequency tuning, which also enables the phase and frequency of the parametric coupling to be varied, and we show that the resulting phase and frequency dependence of the amplification follow the theory of parametric resonance. We expect that this phenomenon will be useful for both fundamental studies of dynamic systems with low dissipation and for increasing signal-to-noise ratio in practical applications such as gyroscopes.

Heart failure: a weak link in CHA2 DS2 -VASc.

Science.gov (United States)

Friberg, Leif; Lund, Lars H

2018-02-15

In atrial fibrillation, stroke risk is assessed by the CHA 2 DS 2 -VASc score. Heart failure is included in CHA 2 DS 2 -VASc, but the rationale is uncertain. Our objective was to test if heart failure is a risk factor for stroke, independent of other risk factors in CHA 2 DS 2 -VASc. We studied 300 839 patients with atrial fibrillation in the Swedish Patient Register 2005-11. Three definitions of heart failure were used in order to assess the robustness of the results. In the main analysis, heart failure was defined by a hospital discharge diagnosis of heart failure as first or second diagnosis and a filled prescription of a diuretic within 3 months before index + 30 days. The second definition counted first or second discharge diagnoses failure diagnosis in open or hospital care before index + 30 days. Associations with outcomes were assessed with multivariable Cox analyses. Patients with heart failure were older (80.5 vs. 74.0 years, P failure and 3.1% without. Adjustment for the cofactors in CHA 2 DS 2 -VASc eradicated the difference in stroke risk between patients with and without heart failure (hazard ratio 1.01 with 95% confidence interval 0.96-1.05). The area under the receiver operating characteristic curve for CHA 2 DS 2 -VASc was not improved by points for heart failure. A clinical diagnosis of heart failure was not an independent risk factor for stroke in patients with atrial fibrillation, which may have implications for anticoagulation management. © 2018 The Authors. ESC Heart Failure published by John Wiley & Sons Ltd on behalf of the European Society of Cardiology.

Advanced Heart Failure

Science.gov (United States)

... Artery Disease Venous Thromboembolism Aortic Aneurysm More Advanced Heart Failure Updated:May 9,2017 When heart failure (HF) ... Making This content was last reviewed May 2017. Heart Failure • Home • About Heart Failure • Causes and Risks for ...

Quantifying the Micromechanical Effects of Variable Cement in Granular Porous Media

Energy Technology Data Exchange (ETDEWEB)

Goodwin, Laurel B.; Boutt David F.

2010-02-18

The mechanical and hydrologic behavior of clastic rocks and sediments is fundamentally controlled by variables such as grain size and shape, sorting, grain and cement mineralogy, porosity, and %cement - parameters that are not used directly in field-scale models of coupled flow and deformation. To improve our understanding of the relationship between these micromechanical properties and bulk behavior we focused on (1) relating detailed, quantitative characterization of the grain-pore systems to both hydrologic and mechanical properties of a suite of variably quartz-cemented quartz arenite samples and (2) the use of a combination of discrete element method (DEM) and poroelastic models parameterized by data from the natural samples to isolate and compare the influence of changes in the mechanical and hydrologic properties of granular porous media due to changes in degree of cementation. Quartz overgrowths, the most common form of authigenic cements in sandstones, are responsible for significant porosity and permeability reduction. The distribution of quartz overgrowths is controlled by available pore space and the crystallographic orientations of individual quartz grains. Study of the St. Peter Sandstone allowed evaluation of the relative effects of quartz cementation and compaction on final grain and pore morphology, showing that progressive quartz cementation modifies the grain framework in consistent, predictable ways. Detailed microstructural characterization and multiple regression analyses show that with progressive diagenesis, the number and length of grain contacts increases as the number of pores increases, the number of large, well-connected pores decreases, and pores become rounder. These changes cause a decrease in pore size variability that leads to a decrease in bulk permeability and both stiffening and strengthening of the grain framework. The consistent nature of these changes allows us to predict variations in hydrologic and mechanical properties

Statistical analysis of human maintenance failures of a nuclear power plant

International Nuclear Information System (INIS)

Pyy, P.

2000-01-01

In this paper, a statistical study of faults caused by maintenance activities is presented. The objective of the study was to draw conclusions on the unplanned effects of maintenance on nuclear power plant safety and system availability. More than 4400 maintenance history reports from the years 1992-1994 of Olkiluoto BWR nuclear power plant (NPP) were analysed together with the maintenance personnel. The human action induced faults were classified, e.g., according to their multiplicity and effects. This paper presents and discusses the results of a statistical analysis of the data. Instrumentation and electrical components are especially prone to human failures. Many human failures were found in safety related systems. Similarly, several failures remained latent from outages to power operation. The safety significance was generally small. Modifications are an important source of multiple human failures. Plant maintenance data is a good source of human reliability data and it should be used more, in future. (orig.)

Mesoscale simulation of concrete spall failure

Science.gov (United States)

Knell, S.; Sauer, M.; Millon, O.; Riedel, W.

2012-05-01

Although intensively studied, it is still being debated which physical mechanisms are responsible for the increase of dynamic strength and fracture energy of concrete observed at high loading rates, and to what extent structural inertia forces on different scales contribute to the observation. We present a new approach for the three dimensional mesoscale modelling of dynamic damage and cracking in concrete. Concrete is approximated as a composite of spherical elastic aggregates of mm to cm size embedded in an elastic cement stone matrix. Cracking within the matrix and at aggregate interfaces in the μm range are modelled with adaptively inserted—initially rigid—cohesive interface elements. The model is applied to analyse the dynamic tensile failure observed in Hopkinson-Bar spallation experiments with strain rates up to 100/s. The influence of the key mesoscale failure parameters of strength, fracture energy and relative weakening of the ITZ on macromechanic strength, momentum and energy conservation is numerically investigated.

The analysis of failure data in the presence of critical and degraded failures

International Nuclear Information System (INIS)

Haugen, Knut; Hokstad, Per; Sandtorv, Helge

1997-01-01

Reported failures are often classified into severityclasses, e.g., as critical or degraded. The critical failures correspond to loss of function(s) and are those of main concern. The rate of critical failures is usually estimated by the number of observed critical failures divided by the exposure time, thus ignoring the observed degraded failures. In the present paper failure data are analyzed, applying an alternative estimate for the critical failure rate, also taking the number of observed degraded failures into account. The model includes two alternative failure mechanisms, one being of the shock type, immediately leading to a critical failure, another resulting in a gradual deterioration, leading to a degraded failure before the critical failure occurs. Failure data on safety valves from the OREDA (Offshore REliability DAta) data base are analyzed using this model. The estimate for the critical failure rate is obtained and compared with the standard estimate

Nonlinear dynamics in micromechanical and nanomechanical resonators and oscillators

Science.gov (United States)

Dunn, Tyler

dynamics in passive resonators, self-sustained MEMS are becoming increasingly prevalent in both research and technology for crucial objectives, such as measurement of time. Despite some effort, much work remains in order to understand phase noise and stability for an oscillator based upon a nonlinear resonator. With the eventual goal of making comprehensive measurements of such a nonlinear oscillator with controlled amplitude and phase, this work describes the realization of a micromechanical phase feedback oscillator.

Intrinsic Energy Dissipation Limits in Nano and Micromechanical Resonators

Science.gov (United States)

Iyer, Srikanth Subramanian

Resonant microelectromechanical Systems (MEMS) have enabled miniaturization of high-performance inertial sensors, radio-frequency filters, timing references and mass-based chemical sensors. Despite the increasing prevalence of MEMS resonators for these applications, the energy dissipation in these structures is not well-understood. Accurate prediction of the energy loss and the resulting quality factor (Q) has significant design implications because it is directly related to device performance metrics including sensitivity for resonant sensors, bandwidth for radio-frequency filters and phase-noise for timing references. In order to assess the future potential for MEMS resonators it is critically important to evaluate the energy dissipation limits, which will dictate the ultimate performance resonant MEMS devices can achieve. This work focuses on the derivation and evaluation of the intrinsic mechanical energy dissipation limit for single-crystal nano and micromechanical resonators due to anharmonic phonon-phonon scattering in the Akhiezer regime. The energy loss is derived using perturbation theory and the linearized Boltzmann transport equation for phonons, and includes the direction and polarization dependent mode-Gruneisen parameters in order to capture the strain-induced anharmonicity among phonon branches. Evaluation of the quality factor limit reveals that Akhiezer damping, previously thought to depend only on material properties, has a strong dependence on crystal orientation and resonant mode shape. The robust model provides a dissipation limit for all resonant modes including shear-mode vibrations, which have significantly reduced energy loss because dissipative phonon-phonon scattering is restricted to volume-preserving phonon branches, indicating that Lame or wine-glass mode resonators will have the highest upper limit on mechanical efficiency. Finally, the analytical dissipation model is integrated with commercial finite element software in order to

Failure analysis of boiler tubes in lakhra coal power plant

International Nuclear Information System (INIS)

Shah, A.; Baluch, M.M.; Ali, A.

2010-01-01

Present work deals with the failure analysis of a boiler tube in Lakhra fluidized bed combustion power station. Initially, visual inspection technique was adopted to analyse the fractured surface. Detailed microstructural investigations of the busted boiler tube were carried out using light optical microscope and scanning electron microscope. The hardness tests were also performed. A 50 percent decrease in hardness of intact portion of the tube material and from area adjacent to failure was measured, which was found to be in good agreement with the wall thicknesses measured of the busted boiler tube i.e. 4 mm and 2 mm from unaffected portion and ruptured area respectively. It was concluded that the major cause of failure of boiler tube is erosion of material which occurs due the coal particles strike at the surface of the tube material. Since the temperature of boiler is not maintained uniformly. The variations in boiler temperature can also affect the material and could be another reason for the failure of the tube. (author)

Balancing burn-in and mission times in environments with catastrophic and repairable failures

International Nuclear Information System (INIS)

Bebbington, Mark; Lai, C.-D.; Zitikis, Ricardas

2009-01-01

In a system subject to both repairable and catastrophic (i.e., nonrepairable) failures, 'mission success' can be defined as operating for a specified time without a catastrophic failure. We examine the effect of a burn-in process of duration τ on the mission time x, and also on the probability of mission success, by introducing several functions and surfaces on the (τ,x)-plane whose extrema represent suitable choices for the best burn-in time, and the best burn-in time for a desired mission time. The corresponding curvature functions and surfaces provide information about probabilities and expectations related to these burn-in and mission times. Theoretical considerations are illustrated with both parametric and, separating the failures by failure mode, nonparametric analyses of a data set, and graphical visualization of results.

The influence of finite-length flaw effects on PTS analyses

International Nuclear Information System (INIS)

Keeney-Walker, J.; Dickson, T.L.

1993-01-01

Current licensing issues within the nuclear industry dictate a need to investigate the effects of cladding on the extension of small finite-length cracks near the inside surface of a vessel. Because flaws having depths of the order of the combined clad and heat affected zone thickness dominate the frequency distribution of flaws, their initiation probabilities can govern calculated vessel failure probabilities. Current pressurized-thermal-shock (PTS) analysis computer programs recognize the influence of the inner-surface cladding layer in the heat transfer and stress analysis models, but assume the cladding fracture toughness is the same as that for the base material. The programs do not recognize the influence cladding may have in inhibiting crack initiation and propagation of shallow finite-length surface flaws. Limited experimental data and analyses indicate the cladding can inhibit the propagation of certain shallow flaws. This paper describes an analytical study which was carried out to determine (1) the minimum flaw depth for crack initiation under PTS loading for semicircular surface flaws in a clad reactor pressure vessel and (2) the impact, in terms of the conditional probability of vessel failure, of using a semicircular surface flaw as the initial flaw and assuming that the flaw cannot propagate in the cladding. The analytical results indicate that for initiation a much deeper critical crack depth is required for the finite-length flaw than for the infinite-length flaw, except for the least severe transient. The minimum flaw depths required for crack initiation from the finite-length flaw analyses were incorporated into a modified version of the OCA-P code. The modified code was applied to the analysis of selected PTS transients, and the results produced a substantial decrease in the conditional probability of failure. This initial study indicates a significant effect on probabilistic fracture analyses by incorporating finite-length flaw results

Inotropes do not increase mortality in advanced heart failure

Directory of Open Access Journals (Sweden)

Guglin M

2014-05-01

Full Text Available Maya Guglin, Marc KaufmanUniversity of South Florida, Tampa, FL, USAAbstract: Inotrope use is one of the most controversial topics in the management of heart failure. While the heart failure community utilizes them and recognizes the state of inotrope dependency, retrospective analyses and registry data have overwhelmingly suggested high mortality, which is logically to be expected given the advanced disease states of those requiring their use. Currently, there is a relative paucity of randomized control trials due to the ethical dilemma of creating control groups by withholding inotropes from patients who require them. Nonetheless, results of such trials have been mixed. Many were also performed with agents no longer in use, on patients without an indication for inotropes, or at a time before automatic cardio-defibrillators were recommended for primary prevention. Thus, their results may not be generalizable to current clinical practice. In this review, we discuss current indications for inotrope use, specifically dobutamine and milrinone, depicting their mechanisms of action, delineating their patterns of use in clinical practice, defining the state of inotrope dependency, and ultimately examining the literature to ascertain whether evidence is sufficient to support the current view that these agents increase mortality in patients with heart failure. Our conclusion is that the evidence is insufficient to link inotropes and increased mortality in low output heart failure.Keywords: inotropes, dobutamine, milrinone, heart failure

Modular titanium alloy neck adapter failures in hip replacement - failure mode analysis and influence of implant material

Directory of Open Access Journals (Sweden)

Bloemer Wilhelm

2010-01-01

Full Text Available Abstract Background Modular neck adapters for hip arthroplasty stems allow the surgeon to modify CCD angle, offset and femoral anteversion intraoperatively. Fretting or crevice corrosion may lead to failure of such a modular device due to high loads or surface contamination inside the modular coupling. Unfortunately we have experienced such a failure of implants and now report our clinical experience with the failures in order to advance orthopaedic material research and joint replacement surgery. The failed neck adapters were implanted between August 2004 and November 2006 a total of about 5000 devices. After this period, the titanium neck adapters were replaced by adapters out of cobalt-chromium. Until the end of 2008 in total 1.4% (n = 68 of the implanted titanium alloy neck adapters failed with an average time of 2.0 years (0.7 to 4.0 years postoperatively. All, but one, patients were male, their average age being 57.4 years (36 to 75 years and the average weight 102.3 kg (75 to 130 kg. The failures of neck adapters were divided into 66% with small CCD of 130° and 60% with head lengths of L or larger. Assuming an average time to failure of 2.8 years, the cumulative failure rate was calculated with 2.4%. Methods A series of adapter failures of titanium alloy modular neck adapters in combination with a titanium alloy modular short hip stem was investigated. For patients having received this particular implant combination risk factors were identified which were associated with the occurence of implant failure. A Kaplan-Meier survival-failure-analysis was conducted. The retrieved implants were analysed using microscopic and chemical methods. Modes of failure were simulated in biomechanical tests. Comparative tests included modular neck adapters made of titanium alloy and cobalt chrome alloy material. Results Retrieval examinations and biomechanical simulation revealed that primary micromotions initiated fretting within the modular tapered neck

Physical Exercise and Patients with Chronic Renal Failure: A Meta-Analysis

Science.gov (United States)

Qiu, Zhenzhen; Zheng, Kai; Zhang, Haoxiang; Feng, Ji; Wang, Lizhi

2017-01-01

Chronic renal failure is a severe clinical problem which has some significant socioeconomic impact worldwide and hemodialysis is an important way to maintain patients' health state, but it seems difficult to get better in short time. Considering these, the aim in our research is to update and evaluate the effects of exercise on the health of patients with chronic renal failure. The databases were used to search for the relevant studies in English or Chinese. And the association between physical exercise and health state of patients with chronic renal failure has been investigated. Random-effect model was used to compare the physical function and capacity in exercise and control groups. Exercise is helpful in ameliorating the situation of blood pressure in patients with renal failure and significantly reduces VO2 in patients with renal failure. The results of subgroup analyses show that, in the age >50, physical activity can significantly reduce blood pressure in patients with renal failure. The activity program containing warm-up, strength, and aerobic exercises has benefits in blood pressure among sick people and improves their maximal oxygen consumption level. These can help patients in physical function and aerobic capacity and may give them further benefits. PMID:28316986

Chronic heart failure

OpenAIRE

Hopper, Ingrid; Easton, Kellie

2017-01-01

1. The common symptoms and signs of chronic heart failure are dyspnoea, ankle swelling, raised jugular venous pressure and basal crepitations. Other conditions may be confused with chronic heart failure, including dependent oedema or oedema due to renal or hepatic disease. Shortness of breath may be due to respiratory disease or severe anaemia. Heart failure secondary to lung disease (cor pulmonale) should be distinguished from congestive cardiac failure. Heart failure may also present with l...

Automatically produced FRP beams with embedded FOS in complex geometry: process, material compatibility, micromechanical analysis, and performance tests

Science.gov (United States)

Gabler, Markus; Tkachenko, Viktoriya; Küppers, Simon; Kuka, Georg G.; Habel, Wolfgang R.; Milwich, Markus; Knippers, Jan

2012-04-01

The main goal of the presented work was to evolve a multifunctional beam composed out of fiber reinforced plastics (FRP) and an embedded optical fiber with various fiber Bragg grating sensors (FBG). These beams are developed for the use as structural member for bridges or industrial applications. It is now possible to realize large scale cross sections, the embedding is part of a fully automated process and jumpers can be omitted in order to not negatively influence the laminate. The development includes the smart placement and layout of the optical fibers in the cross section, reliable strain transfer, and finally the coupling of the embedded fibers after production. Micromechanical tests and analysis were carried out to evaluate the performance of the sensor. The work was funded by the German ministry of economics and technology (funding scheme ZIM). Next to the authors of this contribution, Melanie Book with Röchling Engineering Plastics KG (Haren/Germany; Katharina Frey with SAERTEX GmbH & Co. KG (Saerbeck/Germany) were part of the research group.

Development of Fast Fourier Transform (FFT) micro-mechanical simulations of concrete specimens characterized by micro-X-ray fluorescence

Energy Technology Data Exchange (ETDEWEB)

Giorla, Alain B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-08-01

Concrete in Nuclear Power Plants (NPPs) can be exposed to a wide range of degradation phenomena. In the past years, the Light Water Reactor Sustainability (LWRS) program has investigated Radiation-Induced Volumetric Expansion (RIVE) as a potential degradation mechanism for concrete biological shields [Graves et al., 2014, Rosseel et al., 2016]. RIVE causes swelling and micro-mechanical damage in concrete due to the amorphization of mineral phases contained in the aggregates under neutron irradiation [Hilsdorf et al., 1978, Rosseel et al., 2016]. For long-term operations, it is critical to assess the durability of concrete after 60 or 80 years of exposure to NPP operating conditions against this phenomenon. RIVE is dependent on the composition of the aggregates used in concrete. Quartz-bearing aggregates are more sensitive to RIVE than calcite-bearing aggregates, for example. However, the aggregate composition of a specific plant is generally not explicitly given in the concrete formulation, which makes it nearly impossible to predict the resistance of that concrete to RIVE. Additional characterization is needed to identify the radiation-sensitive mineral phases contained in the aggregates.

Damage Modeling Of Injection-Molded Short- And Long-Fiber Thermoplastics

International Nuclear Information System (INIS)

Nguyen, Ba Nghiep; Kunc, Vlastimil; Bapanapalli, Satish K.; Phelps, Jay; Tucker, Charles L. III

2009-01-01

This article applies the recent anisotropic rotary diffusion - reduced strain closure (ARD-RSC) model for predicting fiber orientation and a new damage model for injection-molded long-fiber thermoplastics (LFTs) to analyze progressive damage leading to total failure of injection-molded long-glass-fiber/polypropylene (PP) specimens. The ARD-RSC model was implemented in a research version of the Autodesk Moldflow Plastics Insight (MPI) processing code, and it has been used to simulate injection-molding of a long-glass-fiber/PP plaque. The damage model combines micromechanical modeling with a continuum damage mechanics description to predict the nonlinear behavior due to plasticity coupled with damage in LFTs. This model has been implemented in the ABAQUS finite element code via user-subroutines and has been used in the damage analyses of tensile specimens removed from the injection-molded long-glass-fiber/PP plaques. Experimental characterization and mechanical testing were performed to provide input data to support and validate both process modeling and damage analyses. The predictions are in agreement with the experimental results.

Fracture morphology of carbon fiber reinforced plastic composite laminates

Directory of Open Access Journals (Sweden)

Vinod Srinivasa

2010-09-01

Full Text Available Carbon fiber reinforced plastic (CFRP composites have been extensively used in fabrication of primary structures for aerospace, automobile and other engineering applications. With continuous and widespread use of these composites in several advanced technology, the frequency of failures is likely to increase. Therefore, to establish the reasons for failures, the fracture modes should be understood thoroughly and unambiguously. In this paper, CFRP composite have been tested in tension, compression and flexural loadings; and microscopic study with the aid of Scanning Electron Microscope (SEM has been performed on failed (fractured composite surfaces to identify the principle features of failure. Efforts have been made in correlating the fracture surface characteristics to the failure mode. The micro-mechanics analysis of failure serves as a useful guide in selecting constituent materials and designing composites from the failure behavior point of view. Also, the local failure initiation results obtained here has been reliably extended to global failure prediction.

Microbuckling compression failure of a radiation-induced wood/polymer composite

International Nuclear Information System (INIS)

Boey, F.Y.C.

1990-01-01

A wood/polymer composite was produced by impregnating Ramin wood with methyl methacrylate monomer and subsequently polymerizing it by gamma irradiation. To assess the improvement in compression strength of the wood caused by the polymer impregnation, a microbuckling compression failure mechanism was used to model the compression failure of the composite. Such a mechanism was found to predict a linear relationship between the compression strength and the percentage polymer impregnation (by weight). Uniaxial compression test results at 45(±5)% and 90(±5)% relative humidity levels, after being statistically analysed, showed that such a linear relationship was valid for up to 100% polymer impregnation. (author)

Failures in combined knowledge and material supply chains

DEFF Research Database (Denmark)

Koch, Christian

2005-01-01

by configuration by project. In such a setting creating value for the customers and the enterprises becomes dependent of the ability to organise and coordinate in the supply chains. That the configuration is not always successful can be demonstrated by studying the emergence of failures occurring in the supply......-month observation period. These were compiled and analysed. The economic consequences are calculated to be 8% of the production costs. The analysis of relations in the supply chain both shows relations to materials and knowledge chains and their interaction. Most of the failures were generated in the knowledge...... stream and then occasionally transfer into the material stream. The paper proposes initiatives to strengthen partnerships in supply chains and especially at engineer to order production. The contradiction between the permanent enterprise organisation potentially capable of handling purchasing...

Failure Analysis of Cracked FS-85 Tubing and ASTAR-811C End Caps

International Nuclear Information System (INIS)

ME Petrichek

2006-01-01

Failure analyses were performed on cracked FS-85 tubing and ASTAR-811C and caps which had been fabricated as components of biaxial creep specimens meant to support materials testing for the NR Space program. During the failure analyses of cracked FS-85 tubing, it was determined that the failure potentially could be due to two effects: possible copper contamination from the EDM (electro-discharge machined) recast layer and/or an insufficient solution anneal. to prevent similar failures in the future, a more formal analysis should be done after each processing step to ensure the quality of the material before further processing. During machining of the ASTAR-811FC rod to form end caps for biaxial creep specimens, linear defects were observed along the center portion of the end caps. These defects were only found in material that was processed from the top portion of the ingot. The linear defects were attributed to a probable residual ingot pipe that was not removed from the ingot. During the subsequent processing of the ingot to rod, the processing temperatures were not high enough to allow self healing of the ingot's residual pipe defect. To prevent this from occurring in the future, it is necessary to ensure that complete removal of the as-melted ingot pipe is verified by suitable non-destructive evaluation (NDE)

Heart failure - tests

Science.gov (United States)

CHF - tests; Congestive heart failure - tests; Cardiomyopathy - tests; HF - tests ... the best test to: Identify which type of heart failure (systolic, diastolic, valvular) Monitor your heart failure and ...

Types of Heart Failure

Science.gov (United States)

... Introduction Types of Heart Failure Classes of Heart Failure Heart Failure in Children Advanced Heart Failure • Causes and ... and procedures related to heart disease and stroke. Heart Failure Questions to Ask Your Doctor Use these questions ...

Modeling of mesoscale dispersion effect on the piezoresistivity of carbon nanotube-polymer nanocomposites via 3D computational multiscale micromechanics methods

International Nuclear Information System (INIS)

Ren, Xiang; Seidel, Gary D; Chaurasia, Adarsh K; Oliva-Avilés, Andrés I; Ku-Herrera, José J; Avilés, Francis

2015-01-01

In uniaxial tension and compression experiments, carbon nanotube (CNT)-polymer nanocomposites have demonstrated exceptional mechanical and coupled electrostatic properties in the form of piezoresistivity. In order to better understand the correlation of the piezoresistive response with the CNT dispersion at the mesoscale, a 3D computational multiscale micromechanics model based on finite element analysis is constructed to predict the effective macroscale piezoresistive response of CNT/polymer nanocomposites. The key factors that may contribute to the overall piezoresistive response, i.e. the nanoscale electrical tunneling effect, the inherent CNT piezoresistivity and the CNT mesoscale network effect are incorporated in the model based on a 3D multiscale mechanical–electrostatic coupled code. The results not only explain how different nanoscale mechanisms influence the overall macroscale piezoresistive response through the mesoscale CNT network, but also give reason and provide bounds for the wide range of gauge factors found in the literature offering insight regarding how control of the mesoscale CNT networks can be used to tailor nanocomposite piezoresistive response. (paper)

Classes of Heart Failure

Science.gov (United States)

... Introduction Types of Heart Failure Classes of Heart Failure Heart Failure in Children Advanced Heart Failure • Causes and ... and Advanced HF • Tools and Resources • Personal Stories Heart Failure Questions to Ask Your Doctor Use these questions ...

Experimental and Numerical Analyses of Dynamic Deformation and Failure in Marine Structures Subjected to Underwater Impulsive Loads

Science.gov (United States)

2012-08-01

fraction of glass fibers and directionality of fibers with respect to external loads. E-glass fibers are the most widely used reinforcement for...Imacon 200D high-speed camera. Gas ReservoirValveGun BarrelWater-chamberFlash Gun Chronograph Support BeamHigh-Speed Camera Breech 61...Explicit User’s Manual, Version 6.9. 2009. 102. Hooputra, H., et al., A comprehensive failure model for crashworthiness simulation of aluminium

Light curing through glass ceramics: effect of curing mode on micromechanical properties of dual-curing resin cements.

Science.gov (United States)

Flury, Simon; Lussi, Adrian; Hickel, Reinhard; Ilie, Nicoleta

2014-04-01

The aim of this study was to investigate micromechanical properties of five dual-curing resin cements after different curing modes including light curing through glass ceramic materials. Vickers hardness (VH) and indentation modulus (Y HU) of Panavia F2.0, RelyX Unicem 2 Automix, SpeedCEM, BisCem, and BeautiCem SA were measured after 1 week of storage (37 °C, 100 % humidity). The resin cements were tested following self-curing or light curing with the second-generation light-emitting diode (LED) curing unit Elipar FreeLight 2 in Standard Mode (1,545 mW/cm(2)) or with the third-generation LED curing unit VALO in High Power Mode (1,869 mW/cm(2)) or in XtraPower Mode (3,505 mW/cm(2)). Light curing was performed directly or through glass ceramic discs of 1.5 or 3 mm thickness of IPS Empress CAD or IPS e.max CAD. VH and Y HU were analysed with Kruskal-Wallis tests followed by pairwise Wilcoxon rank sum tests (α = 0.05). RelyX Unicem 2 Automix resulted in the highest VH and Y HU followed by BeautiCem SA, BisCem, SpeedCEM, and finally Panavia F2.0. Self-curing of RelyX Unicem 2 Automix and SpeedCEM lowered VH and Y HU compared to light curing whereas self-curing of Panavia F2.0, BisCem, and BeautiCem SA led to similar or significantly higher VH and Y HU compared to light curing. Generally, direct light curing resulted in similar or lower VH and Y HU compared to light curing through 1.5-mm-thick ceramic discs. Light curing through 3-mm-thick discs of IPS e.max CAD generally reduced VH and Y HU for all resin cements except SpeedCEM, which was the least affected by light curing through ceramic discs. The resin cements responded heterogeneously to changes in curing mode. The applied irradiances and light curing times adequately cured the resin cements even through 1.5-mm-thick ceramic discs. When light curing resin cements through thick glass ceramic restorations, clinicians should consider to prolong the light curing times even with LED curing units providing high

Self-care and depression in patients with chronic heart failure.

Science.gov (United States)

Holzapfel, Nicole; Löwe, Bernd; Wild, Beate; Schellberg, Dieter; Zugck, Christian; Remppis, Andrew; Katus, Hugo A; Haass, Markus; Rauch, Bernhard; Jünger, Jana; Herzog, Wolfgang; Müller-Tasch, Thomas

2009-01-01

Although chronic heart failure (CHF) is often complicated by comorbid depression and poor self-care, little is known about their specific association in patients with CHF. To investigate self-care behavior among patients with CHF with different degrees of depression severity. A total of 287 patients with documented CHF, New York Heart Association functional class II to IV, completed the European Heart Failure Self-Care Behavior Scale. The Structured Clinical Interview for DSM (SCID) IV served as the criterion standard for the presence of a depressive disorder. Analyses of covariance and linear regression analyses revealed that patients with CHF with minor depression reported significantly lower levels of self-care than patients with major depression (P = .003) and nondepressed patients (P = .014). In addition to minor depression, age (P < or = .001), multimorbidity (P = .01), left ventricular ejection fraction (P = .001), and family status (P = .01) were determinants of self-care. Our results demonstrate that patients with CHF with minor depression and not major depression are at higher risk for poor self-care and its resulting consequences, such as symptom deterioration and frequent hospitalization.

Guidelines for destructive examination of potential MIC [microbiologically influenced corrosion]-related failures

International Nuclear Information System (INIS)

Borenstein, S.S.

1989-01-01

Microbiologically influenced corrosion (MIC) is recognized as a major cause of pitting corrosion failures in natural waters. In order to alleviate the problem, it is important to establish the exact cause of corrosion. If there is a possibility that the failure is due to MIC, a particularly careful failure analysis must be conducted. MIC can be misdiagnosed as attack due to conventional chloride crevice/pitting corrosion unless specialized techniques are used. Certain techniques generally must be employed, including a careful visual examination, is situ bacterial sampling of residual water, bacterial analysis for corrosion products, radiographic examinations, and metallographic examinations. Other techniques may be necessary, or may be very helpful in the analysis, including culture growth, scanning electron microscopy, and ultrasonic examinations. Metallographic examinations can reveal MIC characteristics such as selective pitting of one phase in duplex stainless steel weldments. The methods of failure analysis and their importance are addressed, including each of the steps in the nondestructive examinations and destructive analyses

SOR-ring failure

International Nuclear Information System (INIS)

Kitamura, Hideo

1981-01-01

It was in the autumn of 1976 that the SOR-ring (synchrotron radiation storage ring) has commenced the regular operation. Since then, the period when the operation was interrupted due to the failures of SOR-ring itself is in total about 8 weeks. Failures and accidents have occurred most in the vacuum system. Those failure experiences are described on the vacuum, electromagnet, radio-frequency acceleration and beam transport systems with their interrupted periods. The eleven failures in the vacuum system have been reported, such as bellows breakage in a heating-evacuating period, leakage from the bellows of straight-through valves (made in U.S.A. and Japan), and leakage from the joint flange of the vacuum system. The longest interruption was 5 weeks due to the failure of a domestically manufactured straight-through valve. The failures of the electromagnet system involve the breakage in a cooling water system, short circuit of a winding in the Q magnet power transformer, blow of a fuse protecting the deflection magnet power source by the current less than the rating, and others. The failures of the RF acceleration system include the breakage of an output electronic tube the breakage of a cavity ceramic, RF voltage fluctuation due to the contact deterioration at a cavity electrode, and the failure of grid bias power source. It is necessary to select the highly reliable components for the vacuum system because the vacuum system failures require longer time for recovery, and very likely to induce secondary and tertiary failures. (Wakatsuki, Y.)

Acute liver failure

DEFF Research Database (Denmark)

Larsen, Fin Stolze; Bjerring, Peter Nissen

2011-01-01

Acute liver failure (ALF) results in a multitude of serious complications that often lead to multi-organ failure. This brief review focuses on the pathophysiological processes in ALF and how to manage these.......Acute liver failure (ALF) results in a multitude of serious complications that often lead to multi-organ failure. This brief review focuses on the pathophysiological processes in ALF and how to manage these....

Thermal hydraulic analyses of LVR-15 research reactor with IRT-M fuel

International Nuclear Information System (INIS)

Macek, J.

1997-01-01

The LVR-15 pool-type research reactor has been in operation at the Nuclear Research Institute at Rez since 1955. Following a number of reconstructions and redesigning, the current reactor power is 15 MW. Thermal hydraulic analyses to demonstrate that the core heat will be safely removed during operation as well as in accident situations were performed based on methodology which had been specifically developed for the LVR-15 research reactor. This methodology was applied to stationary thermal hydraulic computations, as well as to transients, particularly with reactivity failure and loss of circulation pumps emergencies. The applied methodology and the core configuration as used in the Safety Report are described. The initial and boundary conditions are then considered and the summary of the calculated failures with regard to the defined safety limits is presented. The results of the core configuration analyses are also discussed with respect to meeting the safety limits and to the applicability of the methodology to this purpose

Experimental approach and micro-mechanical modeling of the mechanical behavior of irradiated zirconium alloys

International Nuclear Information System (INIS)

Onimus, F.

2003-12-01

Zirconium alloys cladding tubes containing nuclear fuel of the Pressurized Water Reactors constitute the first safety barrier against the dissemination of radioactive elements. Thus, it is essential to predict the mechanical behavior of the material in-reactor conditions. This study aims, on the one hand, to identify and characterize the mechanisms of the plastic deformation of irradiated zirconium alloys and, on the other hand, to propose a micro-mechanical modeling based on these mechanisms. The experimental analysis shows that, for the irradiated material, the plastic deformation occurs by dislocation channeling. For transverse tensile test and internal pressure test this channeling occurs in the basal planes. However, for axial tensile test, the study revealed that the plastic deformation also occurs by channeling but in the prismatic and pyramidal planes. In addition, the study of the macroscopic mechanical behavior, compared to the deformation mechanisms observed by TEM, suggested that the internal stress is higher in the case of irradiated material than in the case of non-irradiated material, because of the very heterogeneous character of the plastic deformation. This analysis led to a coherent interpretation of the mechanical behavior of irradiated materials, in terms of deformation mechanisms. The mechanical behavior of irradiated materials was finally modeled by applying homogenization methods for heterogeneous materials. This model is able to reproduce adequately the mechanical behavior of the irradiated material, in agreement with the TEM observations. (author)