Evaluation of gamma and neutron irradiation effects on the properties of mica film capacitors

International Nuclear Information System (INIS)

Roy, Rajesh; Pandya, Arun

2005-01-01

We present an investigation of gamma and neutron radiation effects on mica film capacitors from an electrical point of view. We have studied quantitatively the effects of gamma and neutron irradiation on mica film capacitors of thickness, 20 and 40 μm (0.7874 and 1.5748 mil) with two different areas, 01 and 04 cm 2 . The capacitance has been measured at room temperature in the frequency range 100 Hz-10 MHz. Negligible change in the capacitance due to high gamma dose of 60 Co, 15 kGy at dose rate 0.25 kGy/h, has been observed. However, appreciable change in the capacitance has been observed due to low doses of fast neutrons (cumulative dose, 115 cGy) with flux ∼ 9.925 X 10 7 neutrons/cm 2 h from 252 Cf neutron source of fluence, 2.5 x 10 7 neutrons/s. We have also observed that the impact of gamma and neutron irradiation is more at frequencies higher than 10 kHz, These results show that the mica capacitors do not show any radiation response below 10 kHz. The study shows the radiation response of mica film capacitors to gamma and fast neutron radiations. Mica capacitors show low gamma radiation response in comparison to fast neutron radiation, because a total dose of kGy order has been given by gamma source and only few cGy dose has been given by fast neutron source. (author)

In Situ TEM Electrical Measurements

DEFF Research Database (Denmark)

Canepa, Silvia; Alam, Sardar Bilal; Ngo, Duc-The

2016-01-01

understanding of complex physical and chemical interactions in the pursuit to optimize nanostructure function and device performance. Recent developments of sample holder technology for TEM have enabled a new field of research in the study of functional nanomaterials and devices via electrical stimulation...... influence the sample by external stimuli, e.g. through electrical connections, the TEM becomes a powerful laboratory for performing quantitative real time in situ experiments. Such TEM setups enable the characterization of nanostructures and nanodevices under working conditions, thereby providing a deeper...... and measurement of the specimen. Recognizing the benefits of electrical measurements for in situ TEM, many research groups have focused their effort in this field and some of these methods have transferred to ETEM. This chapter will describe recent advances in the in situ TEM investigation of nanostructured...

Electrical Resistivity Measurements: a Review

Science.gov (United States)

Singh, Yadunath

World-wide interest on the use of ceramic materials for aerospace and other advanced engineering applications, has led to the need for inspection techniques capable of detecting unusually electrical and thermal anomalies in these compounds. Modern ceramic materials offer many attractive physical, electrical and mechanical properties for a wide and rapidly growing range of industrial applications; moreover specific use may be made of their electrical resistance, chemical resistance, and thermal barrier properties. In this review, we report the development and various techniques for the resistivity measurement of solid kind of samples.

Fundamental course of measuring. II. The electrical measuring of non-electrical parameters. Grundkurs der Messtechnik. T. 2. Das elektrische Messen nichtelektrischer Groessen

Energy Technology Data Exchange (ETDEWEB)

Merz, L [Technische Univ. Muenchen (F.R. Germany). Lehrstuhl und Lab. fuer Steuerungs- und Regelungstechnik

1975-01-01

The fundamental course of the electrical measuring of non-electrical parameters aims to fulfill the task of presenting the present knowledge on the basic measuring methods in simple language and illustrative form. The present part II deals especially with measuring methods in heat and process engineering in the industrial field. Following the introduction in part A, the techniques of electrical probes are mainly described, and it is shown which mechanical probes cannot yet be replaced by electrical ones. Part C describes the techniques of measuring transducers.

MICA: Multiple interval-based curve alignment

Science.gov (United States)

Mann, Martin; Kahle, Hans-Peter; Beck, Matthias; Bender, Bela Johannes; Spiecker, Heinrich; Backofen, Rolf

2018-01-01

MICA enables the automatic synchronization of discrete data curves. To this end, characteristic points of the curves' shapes are identified. These landmarks are used within a heuristic curve registration approach to align profile pairs by mapping similar characteristics onto each other. In combination with a progressive alignment scheme, this enables the computation of multiple curve alignments. Multiple curve alignments are needed to derive meaningful representative consensus data of measured time or data series. MICA was already successfully applied to generate representative profiles of tree growth data based on intra-annual wood density profiles or cell formation data. The MICA package provides a command-line and graphical user interface. The R interface enables the direct embedding of multiple curve alignment computation into larger analyses pipelines. Source code, binaries and documentation are freely available at https://github.com/BackofenLab/MICA

A new measure for the strength of electrical synapses

Directory of Open Access Journals (Sweden)

Julie S Haas

2015-09-01

Full Text Available Electrical synapses, like chemical synapses, mediate intraneuronal communication. Electrical synapses are typically quantified by subthreshold measurements of coupling, which fall short in describing their impact on spiking activity in coupled neighbors. Here we describe a novel measurement for electrical synapse strength that directly evaluates the effect of synaptically transmitted activity on spike timing. This method, also applicable to neurotransmitter-based synapses, communicates the considerable strength of electrical synapses. For electrical synapses measured in rodent slices of the thalamic reticular nucleus, spike timing is modulated by tens of ms by activity in a coupled neighbor.

Self-Assembling of Tetradecylammonium Chain on Swelling High Charge Micas (Na-Mica-3 and Na-Mica-2): Effect of Alkylammonium Concentration and Mica Layer Charge.

Science.gov (United States)

Pazos, M Carolina; Cota, Agustín; Osuna, Francisco J; Pavón, Esperanza; Alba, María D

2015-04-21

A family of tetradecylammonium micas is synthesized using synthetic swelling micas with high layer charge (Na(n)Si(8-n)Al(n)Mg6F4O20·XH2O, where n = 2 and 3) exchanged with tetradecylammonium cations. The molecular arrangement of the surfactant is elucidated on the basis of XRD patterns and DTA. The ordering conformation of the surfactant molecules into the interlayer space of micas is investigated by IR/FT, (13)C, (27)Al, and (29)Si MAS NMR. The structural arrangement of the tetradecylammonium cation in the interlayer space of high-charge micas is more sensitive to the effect of the mica layer charge at high concentration. The surfactant arrangement is found to follow the bilayer-paraffin model for all values of layer charge and surfactant concentration. However, at initial concentration below the mica CEC, a lateral monolayer is also observed. The amount of ordered conformation all-trans is directly proportional to the layer charge and surfactant concentration.

Measuring Technology and Mechatronics Automation in Electrical Engineering

CERN Document Server

2012-01-01

Measuring Technology and Mechatronics Automation in Electrical Engineering includes select presentations on measuring technology and mechatronics automation related to electrical engineering, originally presented during the International Conference on Measuring Technology and Mechanatronics Automation (ICMTMA2012). This Fourth ICMTMA, held at Sanya, China, offered a prestigious, international forum for scientists, engineers, and educators to present the state of the art of measuring technology and mechatronics automation research.

Prophylactic and thermovision measurements of electric machines and equipment

International Nuclear Information System (INIS)

Jedlicka, R.; Brestovansky, L.

1996-01-01

High-voltage measurements of generators, unit and service transformers and some significant motor drives used at a nuclear power plant are described in this paper. Thermovision measurements of electric machines and distribution systems are dealt with in the second part of the paper. Power electric equipment represent one of the most significant components of a nuclear power plant. Turbine mechanical energy is converted into the electrical energy within these equipment. Power generated by generators is transformed by transformers so that it can achieve appropriate parameters for both the transmission over the distribution system and the power plant service power supply. The service power supply switchboards and cables provide supply to motors and other consumers necessary for the nuclear power plant technological process. The whole complex of equipment has to be maintained in good technical conditions. It is necessary to make thermovision and prophylactic measurements to identify and verify the electric equipment technical condition. The mentioned measurements warn the operation staff in advance against both gradual deterioration of power connection contact resistances, i.e. power connections overheating, and the machine insulation systems condition deterioration. The operation staff try to prevent the electric equipment operation accidents by early removing the detected failures, thus, improving the nuclear safety. In order to provide the above-mentioned activities a special prophylactic measurement group was established at the NPP Bohunice in 1983. The group specialists make following types of measurements. 1. Prophylactic measurements of electric machines. Prophylactics of 220 MW generators and 6 MW service power generators; Prophylactics of both unit and service transformers and VHV bushings; Prophylactics of major 6 kV motor drives. 2. Thermovision measurements of current connections. Measurements enumarated in paragraph 1 are made on disconnected electric

Calibration-free electrical conductivity measurements for highly conductive slags

International Nuclear Information System (INIS)

Macdonald, Christopher J.; Gao, Huang; Pal, Uday B.; Van den Avyle, James A.; Melgaard, David K.

2000-01-01

This research involves the measurement of the electrical conductivity (K) for the ESR (electroslag remelting) slag (60 wt.% CaF 2 - 20 wt.% CaO - 20 wt.% Al 2 O 3 ) used in the decontamination of radioactive stainless steel. The electrical conductivity is measured with an improved high-accuracy-height-differential technique that requires no calibration. This method consists of making continuous AC impedance measurements over several successive depth increments of the coaxial cylindrical electrodes in the ESR slag. The electrical conductivity is then calculated from the slope of the plot of inverse impedance versus the depth of the electrodes in the slag. The improvements on the existing technique include an increased electrochemical cell geometry and the capability of measuring high precision depth increments and the associated impedances. These improvements allow this technique to be used for measuring the electrical conductivity of highly conductive slags such as the ESR slag. The volatilization rate and the volatile species of the ESR slag measured through thermogravimetric (TG) and mass spectroscopy analysis, respectively, reveal that the ESR slag composition essentially remains the same throughout the electrical conductivity experiments

Analysis of Surface Electric Field Measurements from an Array of Electric Field Mills

Science.gov (United States)

Lucas, G.; Thayer, J. P.; Deierling, W.

2016-12-01

Kennedy Space Center (KSC) has operated an distributed array of over 30 electric field mills over the past 18 years, providing a unique data set of surface electric field measurements over a very long timespan. In addition to the electric field instruments there are many meteorological towers around KSC that monitor the local meteorological conditions. Utilizing these datasets we have investigated and found unique spatial and temporal signatures in the electric field data that are attributed to local meteorological effects and the global electric circuit. The local and global scale influences on the atmospheric electric field will be discussed including the generation of space charge from the ocean surf, local cloud cover, and a local enhancement in the electric field that is seen at sunrise.

Static Measurements on HTS Coils of Fully Superconducting AC Electric Machines for Aircraft Electric Propulsion System

Science.gov (United States)

Choi, Benjamin B.; Hunker, Keith R.; Hartwig, Jason; Brown, Gerald V.

2017-01-01

The NASA Glenn Research Center (GRC) has been developing the high efficiency and high-power density superconducting (SC) electric machines in full support of electrified aircraft propulsion (EAP) systems for a future electric aircraft. A SC coil test rig has been designed and built to perform static and AC measurements on BSCCO, (RE)BCO, and YBCO high temperature superconducting (HTS) wire and coils at liquid nitrogen (LN2) temperature. In this paper, DC measurements on five SC coil configurations of various geometry in zero external magnetic field are measured to develop good measurement technique and to determine the critical current (Ic) and the sharpness (n value) of the super-to-normal transition. Also, standard procedures for coil design, fabrication, coil mounting, micro-volt measurement, cryogenic testing, current control, and data acquisition technique were established. Experimentally measured critical currents are compared with theoretical predicted values based on an electric-field criterion (Ec). Data here are essential to quantify the SC electric machine operation limits where the SC begins to exhibit non-zero resistance. All test data will be utilized to assess the feasibility of using HTS coils for the fully superconducting AC electric machine development for an aircraft electric propulsion system.

Ferro electricity from magnetic order by neutron measurement

International Nuclear Information System (INIS)

Kenzelmann, M.

2009-01-01

Magnetic insulators with competing exchange interactions can give rise to strong fluctuations and qualitatively new ground states. The proximity of such systems to quantum critical points can lead to strong cross-coupling between magnetic long-range order and the nuclear lattice. Case in point is a new class of multiferroic materials in which the magnetic and ferroelectric order parameters are directly coupled, and a magnetic field can suppress or switch the electric polarization [1]. Our neutron measurements reveal that ferro electricity is induced by magnetic order and emerges only if the magnetic structure creates a polar axis [2-5]. Our measurements provide evidence that commensurate magnetic order can produce ferro electricity with large electric polarization [6]. The spin dynamics and the field-temperature phase diagram of the ordered phases provide evidence that competing ground states are essential for ferro electricity. (author)

Molecular dynamics study of room temperature ionic liquids with water at mica surface

Directory of Open Access Journals (Sweden)

Huanhuan Zhang

2018-04-01

Full Text Available Water in room temperature ionic liquids (RTILs could impose significant effects on their interfacial properties at a charged surface. Although the interfaces between RTILs and mica surfaces exhibit rich microstructure, the influence of water content on such interfaces is little understood, in particular, considering the fact that RTILs are always associated with water due to their hygroscopicity. In this work, we studied how different types of RTILs and different amounts of water molecules affect the RTIL-mica interfaces, especially the water distribution at mica surfaces, using molecular dynamics (MD simulation. MD results showed that (1 there is more water and a thicker water layer adsorbed on the mica surface as the water content increases, and correspondingly the average location of K+ ions is farther from mica surface; (2 more water accumulated at the interface with the hydrophobic [Emim][TFSI] than in case of the hydrophilic [Emim][BF4] due to the respective RTIL hydrophobicity and ion size. A similar trend was also observed in the hydrogen bonds formed between water molecules. Moreover, the 2D number density map of adsorbed water revealed that the high-density areas of water seem to be related to K+ ions and silicon/aluminum atoms on mica surface. These results are of great importance to understand the effects of hydrophobicity/hydrophicility of RTIL and water on the interfacial microstructure at electrified surfaces. Keywords: Room temperature ionic liquids, Hydrophobicity/hydrophicility, Water content, Electrical double layer, Mica surface

Longitudinal and transverse electric field measurements in resonant cavities

International Nuclear Information System (INIS)

Tong Dechun; Chen Linfeng; Zheng Xiaoyue

1994-01-01

The paper presents a measuring technique for the electric field distribution of high order modes in resonant cavities. A perturbing bead-like cage made with metallic wires are developed for S-band field measurements, which can be used to detect a small electric field component in the presence of other strong electric or magnetic field components (That means high sensitivity and high directivity). In order to avoid orientation error for the cage with very high directivity, two parallel threads were used for supporting the perturbing cage. A simple mechanical set-up is described. The cage can be driven into the cavity on-axis or off-axis in any azimuth for the longitudinal and transverse electric field measurements

A Power-Frequency Electric Field Sensor for Portable Measurement.

Science.gov (United States)

Xiao, Dongping; Ma, Qichao; Xie, Yutong; Zheng, Qi; Zhang, Zhanlong

2018-03-31

In this paper, a new type of electric field sensor is proposed for the health and safety protection of inspection staff in high-voltage environments. Compared with the traditional power frequency electric field measurement instruments, the portable instrument has some special performance requirements and, thus, a new kind of double spherical shell sensor is presented. First, the mathematical relationships between the induced voltage of the sensor, the output voltage of the measurement circuit, and the original electric field in free space are deduced theoretically. These equations show the principle of the proposed sensor to measure the electric field and the effect factors of the measurement. Next, the characteristics of the sensor are analyzed through simulation. The simulation results are in good agreement with the theoretical analysis. The influencing rules of the size and material of the sensor on the measurement results are summarized. Then, the proposed sensor and the matching measurement system are used in a physical experiment. After calibration, the error of the measurement system is discussed. Lastly, the directional characteristic of the proposed sensor is experimentally tested.

Electric Field Measurement of the Living Human Body for Biomedical Applications: Phase Measurement of the Electric Field Intensity

Directory of Open Access Journals (Sweden)

Ichiro Hieda

2013-01-01

Full Text Available The authors are developing a technique for conducting measurements inside the human body by applying a weak electric field at a radio frequency (RF. Low RF power is fed to a small antenna, and a similar antenna located 15–50 cm away measures the electric field intensity. Although the resolution of the method is low, it is simple, safe, cost-effective, and able to be used for biomedical applications. One of the technical issues suggested by the authors' previous studies was that the signal pattern acquired from measurement of a human body was essentially different from that acquired from a phantom. To trace the causes of this difference, the accuracy of the phase measurements was improved. This paper describes the new experimental system that can measure the signal phase and amplitude and reports the results of experiments measuring a human body and a phantom. The results were analyzed and then discussed in terms of their contribution to the phase measurement.

Estudio computacional de reacciones químicas en entornos acuosos

OpenAIRE

Elola, María Dolores

2002-01-01

En este trabajo hemos estudiado aspectos dinámicos y de equilibrio relacionados con procesos reactivos que toman lugar en agregados acuosos, mediante técnicas de simulación de Dinámica Molecular. La metodología empleada consiste en un esquema mixto cuántico-clásico, que involucra un cálculo de estructura electrónica sobre una porción del sistema -aquella en la cual la densidad electrónica cambia sustancialmente durante la reacción- en conjunto con potenciales empíricos de campo medio para mod...

Electric and magnetic field measurements in an outdoor electric power substation

Energy Technology Data Exchange (ETDEWEB)

Safigianni, A.S.; Tsompanidou, C.G. [Democritus Univ. Thrace, Xanthi (Greece). Dept. of Electrical and Computer Engineering

2006-07-01

With the ever increasing environmental exposure to man-made electromagnetic fields (EMFs), public concern regarding the potential health hazards of exposure to electric and magnetic fields at extremely low frequencies (ELF) has also increased. This paper examined the ELF fields at a 150/20 kV outdoor electric power substation in Xanthi, Greece. Basic data regarding this substation was provided along with previous relevant research studies. The reference levels for safe general public and occupational exposure according to the International Commission on Non-Ionizing Radiation Protection (ICNIRP) was also presented. The instruments used to take the measurements were described and indicative results of the EMFs measurements in the substation were provided. In general, the measured magnetic flux density values were far below the reference level for safe public and occupational exposure. No significant differentiation was noted in these values in relation to body height. However, the levels were found to be in violation in two positions, near the capacitor banks. It was emphasized that these values greatly decreased with distance, and the positions where these high values were measured were not occupied by technicians when the capacitors were under voltage. In addition, it was emphasized that the measured magnetic flux density values were very small in the supervision room, where the supervisor of the substation works and in the ring zone where the public has access. All the measured electric field strength values were below the reference level for safe public and occupational exposure. It was concluded that the measured field values are within recognized guidelines and pose no danger for public or working personnel. 19 refs., 1 tab., 4 figs.

Prophylactic and thermovision measurements of electric machines and equipment

Energy Technology Data Exchange (ETDEWEB)

Jedlicka, R; Brestovansky, L [Atomova Elektraren Bohunice, Jaslovske Bohunice (Slovakia)

1997-12-31

High-voltage measurements of generators, unit and service transformers and some significant motor drives used at a nuclear power plant are described in this paper. Thermovision measurements of electric machines and distribution systems are dealt with in the second part of the paper. Power electric equipment represent one of the most significant components of a nuclear power plant. Turbine mechanical energy is converted into the electrical energy within these equipment. Power generated by generators is transformed by transformers so that it can achieve appropriate parameters for both the transmission over the distribution system and the power plant service power supply. The service power supply switchboards and cables provide supply to motors and other consumers necessary for the nuclear power plant technological process. The whole complex of equipment has to be maintained in good technical conditions. It is necessary to make thermovision and prophylactic measurements to identify and verify the electric equipment technical condition. The mentioned measurements warn the operation staff in advance against both gradual deterioration of power connection contact resistances, i.e. power connections overheating, and the machine insulation systems condition deterioration. The operation staff try to prevent the electric equipment operation accidents by early removing the detected failures, thus, improving the nuclear safety. In order to provide the above-mentioned activities a special prophylactic measurement group was established at the NPP Bohunice in 1983. The group specialists make following types of measurements. 1. Prophylactic measurements of electric machines. Prophylactics of 220 MW generators and 6 MW service power generators; Prophylactics of both unit and service transformers and VHV bushings; Prophylactics of major 6 kV motor drives. 2. Thermovision measurements of current connections. (Abstract Truncated)

Morphology and photoresponse of crystalline antimony film grown on mica by physical vapor deposition

Directory of Open Access Journals (Sweden)

Shafa Muhammad

2016-09-01

Full Text Available Antimony is a promising material for the fabrication of photodetectors. This study deals with the growth of a photosensitive thin film by the physical vapor deposition (PVD of antimony onto mica surface in a furnace tube. The geometry of the grown structures was studied via scanning electron microscopy (SEM, X-ray diffraction (XRD, energy-dispersive X-ray spectroscopy (EDX and elemental diffraction analysis. XRD peaks of the antimony film grown on mica mostly matched with JCPDF Card. The formation of rhombohedral crystal structures in the film was further confirmed by SEM micrographs and chemical composition analysis. The Hall measurements revealed good electrical conductivity of the film with bulk carrier concentration of the order of 1022 Ω·cm-3 and mobility of 9.034 cm2/Vs. The grown film was successfully tested for radiation detection. The photoresponse of the film was evaluated using its current-voltage characteristics. These investigations revealed that the photosensitivity of the antimony film was 20 times higher than that of crystalline germanium.

Electric Field Effects in RUS Measurements

Energy Technology Data Exchange (ETDEWEB)

Darling, Timothy W [Los Alamos National Laboratory; Ten Cate, James A [Los Alamos National Laboratory; Allured, Bradley [UNIV NEVADA, RENO; Carpenter, Michael A [CAMBRIDGE UNIV. UK

2009-09-21

Much of the power of the Resonant Ultrasound Spectroscopy (RUS) technique is the ability to make mechanical resonance measurements while the environment of the sample is changed. Temperature and magnetic field are important examples. Due to the common use of piezoelectric transducers near the sample, applied electric fields introduce complications, but many materials have technologically interesting responses to applied static and RF electric fields. Non-contact optical, buffered, or shielded transducers permit the application of charge and externally applied electric fields while making RUS measurements. For conducting samples, in vacuum, charging produces a small negative pressure in the volume of the material - a state rarely explored. At very high charges we influence the electron density near the surface so the propagation of surface waves and their resonances may give us a handle on the relationship of electron density to bond strength and elasticity. Our preliminary results indicate a charge sign dependent effect, but we are studying a number of possible other effects induced by charging. In dielectric materials, external electric fields influence the strain response, particularly in ferroelectrics. Experiments to study this connection at phase transformations are planned. The fact that many geological samples contain single crystal quartz suggests a possible use of the piezoelectric response to drive vibrations using applied RF fields. In polycrystals, averaging of strains in randomly oriented crystals implies using the 'statistical residual' strain as the drive. The ability to excite vibrations in quartzite polycrystals and arenites is explored. We present results of experimental and theoretical approaches to electric field effects using RUS methods.

Electric Field Quantitative Measurement System and Method

Science.gov (United States)

Generazio, Edward R. (Inventor)

2016-01-01

A method and system are provided for making a quantitative measurement of an electric field. A plurality of antennas separated from one another by known distances are arrayed in a region that extends in at least one dimension. A voltage difference between at least one selected pair of antennas is measured. Each voltage difference is divided by the known distance associated with the selected pair of antennas corresponding thereto to generate a resulting quantity. The plurality of resulting quantities defined over the region quantitatively describe an electric field therein.

Effect of Voltage Measurement on the Quantitative Identification of Transverse Cracks by Electrical Measurements

KAUST Repository

Selvakumaran, Lakshmi

2016-03-24

Electrical tomography can be used as a structural health monitoring technique to identify different damage mechanisms in composite laminates. Previous work has established the link between transverse cracking density and mesoscale conductivity of the ply. Through the mesoscale relationship, the conductivity obtained from electrical tomography can be used as a measure of the transverse cracking density. Interpretation of this measure will be accurate provided the assumptions made during homogenization are valid. One main assumption of mesoscale homogenization is that the electric field is in the plane. Here, we test the validity of this assumption for laminates with varying anisotropy ratios and for different distances between the cracked ply and surface that is instrumented with electrodes. We also show the equivalence in electrical response between measurements from cracked laminates and their equivalent mesoscale counterparts. Finally, we propose some general guidelines on the measurement strategy for maximizing the accuracy of transverse cracks identification.

An electrical method for the measurement of the thermal and electrical conductivity of reduced graphene oxide nanostructures.

Science.gov (United States)

Schwamb, Timo; Burg, Brian R; Schirmer, Niklas C; Poulikakos, Dimos

2009-10-07

This paper introduces an electrical four-point measurement method enabling thermal and electrical conductivity measurements of nanoscale materials. The method was applied to determine the thermal and electrical conductivity of reduced graphene oxide flakes. The dielectrophoretically deposited samples exhibited thermal conductivities in the range of 0.14-2.87 W m(-1) K(-1) and electrical conductivities in the range of 6.2 x 10(2)-6.2 x 10(3) Omega(-1) m(-1). The measured properties of each flake were found to be dependent on the duration of the thermal reduction and are in this sense controllable.

Guide to Flow Measurement for Electric Propulsion Systems

Science.gov (United States)

Frieman, Jason D.; Walker, Mitchell L. R.; Snyder, Steve

2013-01-01

In electric propulsion (EP) systems, accurate measurement of the propellant mass flow rate of gas or liquid to the thruster and external cathode is a key input in the calculation of thruster efficiency and specific impulse. Although such measurements are often achieved with commercial mass flow controllers and meters integrated into propellant feed systems, the variability in potential propellant options and flow requirements amongst the spectrum of EP power regimes and devices complicates meter selection, integration, and operation. At the direction of the Committee on Standards for Electric Propulsion Testing, a guide was jointly developed by members of the electric propulsion community to establish a unified document that contains the working principles, methods of implementation and analysis, and calibration techniques and recommendations on the use of mass flow meters in laboratory and spacecraft electric propulsion systems. The guide is applicable to EP devices of all types and power levels ranging from microthrusters to high-power ion engines and Hall effect thrusters. The establishment of a community standard on mass flow metering will help ensure the selection of the proper meter for each application. It will also improve the quality of system performance estimates by providing comprehensive information on the physical phenomena and systematic errors that must be accounted for during the analysis of flow measurement data. This paper will outline the standard methods and recommended practices described in the guide titled "Flow Measurement for Electric Propulsion Systems."

The transient electric field measurement system for EAST device

Energy Technology Data Exchange (ETDEWEB)

Wang, Y., E-mail: wayong@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui (China); Ji, Z.S. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui (China); Zhu, C.M. [The Experiment & Verification Center of State Grid Electric Power Research Institute (The Automation Equipment EMC Lab. of State Grid Co.), Nanjing, Jiangsu (China); Zhang, Z.C.; Ma, T.F.; Xu, Z.H. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui (China)

2016-11-15

The electromagnetic environment around the Experimental Advanced Superconducting Tokamak (EAST) device is very complex during plasma discharge experiment. In order to fully monitor the changes of electric field around the EAST device during plasma discharge, a transient electric field measurement system based on PCI eXtensions for Instrumentation (PXI) platform has been designed. A digitizer is used for high-speed data acquisition of raw signals from electric field sensors, and a Field Programmable Gate Array (FPGA) module is used for realizing an on-the-fly fast Fourier transform (FFT) and inverse fast Fourier transform (IFFT) algorithm including a beforehand identified antenna factor (AF) to achieve finally a calibrated and filtered electric field measurement, then these signals can be displayed and easily analyzed. The raw signals from electric field sensors are transferred through optical fiber by optical isolation to reduce electromagnetic interference (EMI). The high speed data streaming technology is used for data storage. A prototype of this system has been realized to measure the transient electric field strength, with the real-time processing and continuous acquisition ability of one channel of 14-bit resolution and up to 50 MHz sampling rate, and 6 KHz FFT frequency resolution.

Instantaneous input electrical power measurements of HITU transducer

International Nuclear Information System (INIS)

Karaboece, B; Guelmez, Y; Rajagapol, S; Shaw, A

2011-01-01

HITU (High Intensity Theraupetic Ultrasound) transducers are widely used in therapeutic ultrasound in medicine. The output ultrasonic power of HITU transducer can be measured in number of methods described in IEC 61161 standard [1]. New IEC standards specifically for measurement of HITU equipment are under development. The ultrasound power radiated from a transducer is dependent on applied input electrical voltage and current and consequently power. But, up to now, no standardised method has been developed and adopted for the input electrical power measurements. Hence, a workpackage was carried out for the establishment of such method in the frequency range of 1 to 3 MHz as a part of EURAMET EMRP Era-net plus 'External Beam Cancer Therapy' project. Several current shunts were developed and evaluated. Current measurements were also realized with Philips current probe and preamplifier at NPL and Agilent current probe at UME. In this paper, a method for the measurement of instantaneous electrical power delivered to a reactive ultrasound transducer in the required frequency range is explored.

Instantaneous input electrical power measurements of HITU transducer

Energy Technology Data Exchange (ETDEWEB)

Karaboece, B; Guelmez, Y [Tuebitak Ulusal Metroloji Enstituesue (UME), P.K. 54 41470 Gebze-Kocaeli (Turkey); Rajagapol, S; Shaw, A, E-mail: baki.karaboce@ume.tubitak.gov.t [National Physical Laboratory (NPL), Hampton Road, Teddington TW11 0LW (United Kingdom)

2011-02-01

HITU (High Intensity Theraupetic Ultrasound) transducers are widely used in therapeutic ultrasound in medicine. The output ultrasonic power of HITU transducer can be measured in number of methods described in IEC 61161 standard [1]. New IEC standards specifically for measurement of HITU equipment are under development. The ultrasound power radiated from a transducer is dependent on applied input electrical voltage and current and consequently power. But, up to now, no standardised method has been developed and adopted for the input electrical power measurements. Hence, a workpackage was carried out for the establishment of such method in the frequency range of 1 to 3 MHz as a part of EURAMET EMRP Era-net plus 'External Beam Cancer Therapy' project. Several current shunts were developed and evaluated. Current measurements were also realized with Philips current probe and preamplifier at NPL and Agilent current probe at UME. In this paper, a method for the measurement of instantaneous electrical power delivered to a reactive ultrasound transducer in the required frequency range is explored.

Electric field measurements in a nanosecond pulse discharge in atmospheric air

International Nuclear Information System (INIS)

Simeni Simeni, Marien; Frederickson, Kraig; Lempert, Walter R; Adamovich, Igor V; Goldberg, Benjamin M; Zhang, Cheng

2017-01-01

The paper presents the results of temporally and spatially resolved electric field measurements in a nanosecond pulse discharge in atmospheric air, sustained between a razor edge high-voltage electrode and a plane grounded electrode covered by a thin dielectric plate. The electric field is measured by picosecond four-wave mixing in a collinear phase-matching geometry, with time resolution of approximately 2 ns, using an absolute calibration provided by measurements of a known electrostatic electric field. The results demonstrate electric field offset on the discharge center plane before the discharge pulse due to surface charge accumulation on the dielectric from the weaker, opposite polarity pre-pulse. During the discharge pulse, the electric field follows the applied voltage until ‘forward’ breakdown occurs, after which the field in the plasma is significantly reduced due to charge separation. When the applied voltage is reduced, the field in the plasma reverses direction and increases again, until the weak ‘reverse’ breakdown occurs, producing a secondary transient reduction in the electric field. After the pulse, the field is gradually reduced on a microsecond time scale, likely due to residual surface charge neutralization by transport of opposite polarity charges from the plasma. Spatially resolved electric field measurements show that the discharge develops as a surface ionization wave. Significant surface charge accumulation on the dielectric surface is detected near the end of the discharge pulse. Spatially resolved measurements of electric field vector components demonstrate that the vertical electric field in the surface ionization wave peaks ahead of the horizontal electric field. Behind the wave, the vertical field remains low, near the detection limit, while the horizontal field is gradually reduced to near the detection limit at the discharge center plane. These results are consistent with time-resolved measurements of electric field

Electric field measurements in a xenon discharge using Spark spectroscopy

NARCIS (Netherlands)

Wagenaars, E.; Bowden, M.D.; Kroesen, G.M.W.

2005-01-01

Measurements of electric field distributions in a low-pressure xenon discharge are presented. The measurement technique is based on Stark spectroscopy, using a 2 + 1 excitation scheme with fluorescence dip detection. Electric fields can be measured by detecting Stark shifts of high-lying Rydberg

Two devices for atmospheric electric field measurement

International Nuclear Information System (INIS)

Colombet, Andre; Hubert, Pierre.

1977-02-01

Two instruments installed at St Privat d'Allier for electric field measurement in connection with the rocket triggered lighting experiment program are described. The first one is a radioactive probe electrometer used as a warning device. The second is a field mill used for tape recording of electric field variation during the triggering events. Typical examples of such records are given [fr

Muhlenbergia monandra (Poaceae: Eragrostideae, nueva especie anual endémica del Perú

Directory of Open Access Journals (Sweden)

J. José Alegría Olivera

2001-01-01

Full Text Available Se describe e ilustra Muhlenbergia monandra, endémica de Perú. La nueva especie se caracteriza por sus glumas mayores que el antecio, por tener inflorescencias espiciformes y las flores cleistógamas con un estambre. La anatomía foliar se describe e ilustra y se detallan sus caracteres diferenciales. Se incluyen observaciones sobre la epidermis de la lemma y las glumas realizadas con el Microscopio Electrónico de Barrido. Se discute la posición taxonómica de la nueva entidad y las diferencias con las especies anuales relacionadas que habitan en América del Sur

A Measurement System of Electric Signals on Standing Trees

Directory of Open Access Journals (Sweden)

Hao TIAN

2014-01-01

Full Text Available The standing tree electric signal (STES, defined as the electric potential difference between standing trees and the surrounding soil, can be utilized to reflect the biological nature of the trees. This signal should be measured precisely because it can also be collected and used as the electric power energy. In this paper, the automatic measurement system of standing tree biological electric signal based on MSP430 MCU. First of all, the basic structure of the presented system is introduced and it includes three modules: amplification module of the standing tree electric signal, the acquisition and processing of the signal module and the serial communication module. Then, the performances of the built system are respectively validated by the Poplar, Planetree, and Platanus in Beijing Forestry University. The result indicated that the relative error of this system is less than 2 %. The presented system can be considered as the foundation of the subsequent study on the mechanism of the biological electric signal and the application of the biological electric energy on standing trees.

Electrical conductivity and magnetic permeability measurement of case hardened steels

Science.gov (United States)

Tian, Yong

2015-03-01

For case carburized steels, electrical conductivity and magnetic permeability profiles are needed to develop model-based case depth characterization techniques for the purpose of nondestructive quality control. To obtain fast and accurate measurement of these material properties, four-point potential drop approaches are applied on circular-shaped discs cut from steel rings with different case depths. First, a direct current potential drop (DCPD) approach is applied to measure electrical conductivity. Subsequently, an alternating current potential drop (ACPD) approach is used to measure magnetic permeability. Practical issues in measurement design and implementation are discussed. Depth profiles of electrical conductivity and magnetic permeability are reported.

Electric-field-induced superconductivity detected by magnetization measurements of an electric-double-layer capacitor

International Nuclear Information System (INIS)

Kasahara, Yuichi; Takeuchi, Yuki; Ye, Jianting; Yuan, Hongtao; Shimotani, Hidekazu; Iwasa, Yoshihiro; Nishimura, Takahiro; Sato, Tatsuya

2010-01-01

We report evidence for superconductivity induced by the application of strong electric fields onto the surface of a band insulator, ZrNCl, provided by the observation of a shielding diamagnetic signal. We introduced an electric-double-layer capacitor configuration and in situ magnetization measurements at low temperatures as a method to detect the novel electric-field-induced superconducting state. The results showed excellent agreement with a previous report using a transistor configuration, demonstrating that the present technique is a novel method for investigating the nonequilibrium phase induced by electric fields. (author)

Market power in electricity markets: Beyond concentration measures

International Nuclear Information System (INIS)

Borenstein, S.; Bushnell, J.; Knittel, C.R.

1999-01-01

The wave of electricity market restructuring both within the US and abroad has brought the issue of horizontal market power to the forefront of energy policy. Traditionally, estimation and prediction of market power has relied heavily on concentration measures. In this paper, the authors discuss the weaknesses of concentration measures as a viable measure of market power in the electricity industry, and they propose an alternative method based on market simulations that take advantage of existing plant level data. The authors discuss results from previous studies they have performed, and present new results that allow for the detection of threshold demand levels where market power is likely to be a problem. In addition, the authors analyze the impact of that recent divestitures in the California electricity market will have on estimated market power. They close with a discussion of the policy implications of the results

Measuring of electric fields with laser-induced fluorescence-dip Stark spectroscopy

NARCIS (Netherlands)

Wagenaars, E.; Bowden, M.D.; Kroesen, G.M.W.

2007-01-01

The electric field is an important quantity in low-pressure gas discharges, driving many fundamental processes. Unfortunately, it is difficult to measure electric field distributions in plasmas directly. The goal of this research was to develop a diagnostic technique to measure electric fields in

Investigations on structural iron electrochemical properties in layered silicates using massive mica electrodes

International Nuclear Information System (INIS)

Hadi, J.; Ignatiadis, I.; Tournassat, C.; Charlet, L.; Silvester, E.

2012-01-01

Document available in extended abstract form only. Nuclear waste repositories are being installed in deep excavated rock formations in some places in Europe to isolate and store radioactive waste. In France, the Callovo-Oxfordian formation (COx) is a potential candidate for a nuclear waste repository. The redox reactivity of COx clay rock samples are already under study using microscopic, spectrometric and wet analysis techniques. In order to cross and overcome certain limits by improvement in the knowledge, specific electrodes should be constructed and devoted to the deepening of the electrochemical behaviour of the COx system in different situations. Iron is one of the most common redox species in soils and sedimentary rocks. Iron-bearing phyllosilicates play key roles in various biogeochemical processes. The complexity of the physical and chemical changes involving their structural iron makes the studies of its redox properties challenging. Most of the recent reported efforts were focused on probing Fe redox on finely powdered clay particles, and have been hampered by inadequate interactions between particles and electrodes. Moreover, such experiments usually involve redox probe ions, thus adding supplementary difficulties in the determination of structural iron redox parameters such as redox potential (Eh) and kinetics. The present study aims at qualitatively investigating the above mentioned phenomena on minerals like iron-bearing micas. In the current work, we present initial insights regarding efforts to build a direct electrical interface between solid electrodes and conveniently shaped macroscopic mica crystals in order to investigate the redox properties of structural iron in dry and aqueous environments, in the presence of representative perturbations. A classical three electrode system has been used for voltammetric measurements. Platinum plate was the counter electrode. Potentials have been measured against either silver-silver chloride electrode or

Mica fission detectors

International Nuclear Information System (INIS)

Wong, C.; Anderson, J.D.; Hansen, L.; Lehn, A.V.; Williamson, M.A.

1977-01-01

The present development status of the mica fission detectors is summarized. It is concluded that the techniques have been refined and developed to a state such that the mica fission counters are a reliable and reproducible detector for fission events

Electric field measurements in the auroral E region

International Nuclear Information System (INIS)

Mahon, H.P.; Smiddy, M.; Sagalyn, R.C.

1975-01-01

Dipole electric field, positive ion and electron densities and temperatures, vehicle potential, and plasma sheath measurements have been made in the auroral E region by means of rockets flown from Fort Churchill, Canada. These results are described and compared over the altitude region 100 to 165 km. On a rocket flight launched on 10 December 1969 during very quiet conditions, adjacent to a stable, low intensity auroral arc, the plasma density and temperatures are found to be high and the electric fields large and steady. Electric field components of the order of -17 mv m -1 to +6 mv m -1 were measured along the Earth's magnetic field. The plasma results indicate that these fields may be contributing to enhanced electron temperatures. On a flight of 9 March 1970 during a large magnetic storm with widespread auroral activity, lower plasma densities and temperatures and much smaller and more erratic electric fields were observed with no significant component parallel to the magnetic field. (auth)

Electric field measurements with electro-optical sensor

International Nuclear Information System (INIS)

Brambilla, R.

1992-03-01

When electric field calculations on the surface of electrodes and electrical insulation present difficulties due to complex geometries and diverse dielectric properties, it is sometimes very useful to resort to direct measurements. However, conventional probes, based on the capacitive effect, are not quite suitable for this purpose due to strong perturbations introduced by probes themselves and to difficulties in isolating the sensors from the instrumentation at points of measurement with a high potential. To avoid these difficulties, a measurement system was developed which incorporates a Pockels effect crystal sensor, a moveable HeNe laser beam for signal transmission and beam polarization modulation, and a laser beam analyzer which detects variations in polarization induced by the sensor. This paper describes the key design, operation and performance characteristics of this device

Facing a Problem of Electrical Energy Quality in Ship Networks-measurements, Estimation, Control

Institute of Scientific and Technical Information of China (English)

Tomasz Tarasiuk; Janusz Mindykowski; Xiaoyan Xu

2003-01-01

In this paper, electrical energy quality and its indices in ship electric networks are introduced, especially the meaning of electrical energy quality terms in voltage and active and reactive power distribution indices. Then methods of measurement of marine electrical energy indices are introduced in details and a microprocessor measurement-diagnosis system with the function of measurement and control is designed. Afterwards, estimation and control of electrical power quality of marine electrical power networks are introduced. And finally, according to the existing method of measurement and control of electrical power quality in ship power networks, the improvement of relative method is proposed.

ULF Waves in the Ionospheric Alfven Resonator: Modeling of MICA Observations

Science.gov (United States)

Streltsov, A. V.; Tulegenov, B.

2017-12-01

We present results from a numerical study of physical processes responsible for the generation of small-scale, intense electromagnetic structures in the ultra-low-frequency range frequently observed in the close vicinity of bright discrete auroral arcs. In particular, our research is focused on the role of the ionosphere in generating these structures. A significant body of observations demonstrate that small-scale electromagnetic waves with frequencies below 1 Hz are detected at high latitudes where the large-scale, downward magnetic field-aligned current (FAC) interact with the ionosphere. Some theoretical studies suggest that these waves can be generated by the ionospheric feedback instability (IFI) inside the ionospheric Alfven resonator (IAR). The IAR is the region in the low-altitude magnetosphere bounded by the strong gradient in the Alfven speed at high altitude and the conducting bottom of the ionosphere (ionospheric E-region) at low altitude. To study ULF waves in this region we use a numerical model developed from reduced two fluid MHD equations describing shear Alfven waves in the ionosphere and magnetosphere of the earth. The active ionospheric feedback on structure and amplitude of magnetic FACs that interact with the ionosphere is implemented through the ionospheric boundary conditions that link the parallel current density with the plasma density and the perpendicular electric field in the ionosphere. Our numerical results are compared with the in situ measurements performed by the Magnetosphere-Ionosphere Coupling in the Alfven Resonator (MICA) sounding rocket, launched on February 19, 2012 from Poker Flat Research Range in Alaska to measure fields and particles during a passage through a discreet auroral arc. Parameters of the simulations are chosen to match actual MICA parameters, allowing the comparison in the most precise and rigorous way. Waves generated in the numerical model have frequencies between 0.30 and 0.45 Hz, while MICA measured

Measurement of electric fields in the H-1NF heliac

International Nuclear Information System (INIS)

James, B.W.; Howard, J.

1999-01-01

There are a number of laser induced fluorescence techniques which can be used to measure internal plasma electric fields. It is planned to use a technique based on Stark mixing of energy levels in a supersonic beam containing metastable helium atoms to measure radial electric fields in H-1NF. Enhanced values of radial electric field are associated with improved confinement modes in H-1NF and other magnetically confined plasmas

Electrical measurements on submicronic synthetic conductors : carbon nanotubes

Energy Technology Data Exchange (ETDEWEB)

Langer, L [Unite de Physico-Chimie et de Physique des Materiaux, Univ. Catholique de Louvain, Louvain-la-Neuve (Belgium); Stockman, L [Lab. voor Vaste Stof-Fysika en Magnetisme, Katholieke Univ. Leuven (Belgium); Heremans, J P [Physics Dept., General Motors Research, Warren, MI (United States); Bayot, V [Unite de Physico-Chimie et de Physique des Materiaux, Univ. Catholique de Louvain, Louvain-la-Neuve (Belgium); Olk, C H [Physics Dept., General Motors Research, Warren, MI (United States); Haesendonck, C van [Lab. voor Vaste Stof-Fysika en Magnetisme, Katholieke Univ. Leuven (Belgium); Bruynseraede, Y [Lab. voor Vaste Stof-Fysika en Magnetisme, Katholieke Univ. Leuven (Belgium); Issi, J P [Unite de Physico-Chimie et de Physique des Materiaux, Univ. Catholique de Louvain, Louvain-la-Neuve (Belgium)

1995-03-15

The synthesis of very small samples has raised the need for a drastic miniaturization of the classical four-probe technique in order to realize electrical resistance measurements. Two methods to realize electrical contacts on very small fibers are described here. Using classical photolithography the electrical resistivity of a submicronic catalytic chemical vapour deposited filament is estimated. Scanning tunneling microscopy (STM) lithography allowed to attach small gold contacts to a small bundle (diameter 50 nm) of carbon nanotubes. This bundle is found to exhibit a semimetallic behavior at higher temperature and an unexpected drop of the electrical resistivity at lower temperature. (orig.)

Measuring electric conductivity in liquid metals by eddy current method

International Nuclear Information System (INIS)

Zhuravlev, S.P.; Ostrovskij, O.I.; Grigoryan, V.A.

1982-01-01

Technique permitting to apply the method of vertiginous currents for investigation of electric conductivity of metal melts in the high temperature range is presented. Interferences affecting accuracy of measurements are specified and ways of their removing are pointed out. Scheme of measuring and design of the facility are described. Results of measuring electric resistance of liquid Fe, Co, Ni obtained for the first time by this method are presented. The data obtained agree with the results of measurements conducted by the method of the rotating magnetic field. Difference in absolute values of electric resistance in parallel experiments for each metal does not exceed 4%

Measuring Electrical Current: The Roads Not Taken

Science.gov (United States)

Greenslade, Thomas B., Jr.

2011-01-01

Recently I wrote about the standard Weston meter movement, that is at the heart of all modern analogue current measurements. Now I will discuss other techniques used to measure electric current that, despite being based on valid physical principles, are largely lost in technological history.

Electric field measurements at subcritical, oblique bow shock crossings

International Nuclear Information System (INIS)

Wygant, J.R.; Bensadoun, M.; Mozer, F.S.

1987-01-01

Electric field measurements at oblique, subcritical bow shock crossings are presented from the ISEE 1 University of California, Berkeley, double-probe electric field experiment. The measurements averaged over the 3-s spin period of the spacecraft provide the first observations of the large-scale (100 km) laminar oscillations in the longitudinal component of the electric field associated with the whistler precursor which is characteristic of these dispersive shocks. The amplitude of the oscillations increases from ∼0.5 mV/m to a maximum of 6 mV/m across the magnetic ramp of the shock (directed along the shock normal). The calculated electric potential drops across the shocks varied from 340 to 550 volts, which is 40-60% of the observed loss of kinetic energy associated with the bulk flow of the ions. These measurements suggest that at these shocks the additional deceleration of incident ions is due to the Lorentz force. The contributions to the normal component of the large-scale electric field at the shock due to the parallel and perpendicular components (relative to the magnetic field) of the electric field are evaluated. It is shown that the perpendicular component of the electric field dominates, accounting for most of the cross-shock potential, but that there is a nonnegligible parallel component. This large-scale parallel component has a magnitude of 1-2 mV/m which sometimes results in a potential well for electrons with a depth of ∼150 eV. It is experimentally demonstrated that the dominance of the perpendicular over the parallel component of the electric field resulted in a correlation between the longitudinal component of the large-scale electric field and the fluctuations in the magnetic field component perpendicular to the coplanarity plane

Andamiaje de la autorregulación académica a través del correo electrónico en un programa de formación docente de modalidad mixta

Directory of Open Access Journals (Sweden)

Marcos Antonio Requena Arellano

2016-01-01

Full Text Available La investigación tuvo como objetivo analizar el andamiaje dado a la autorregulación académica mediante el correo electrónico en el primer semestre de un programa universitario de modalidad mixta. Se sustentó en un modelo cíclico del aprendizaje autorregulado, tres tipologías de andamiaje en entorno digital y aportes hechos respecto a la moderación de comunidades de aprendizaje. Se realizó mediante aplicación de técnicas propias del método comparativo continuo de la teoría fundamentada. Los resultados destacan que: a el andamiaje dado por los docentes muestra grandes diferencias de un docente a otro, tanto en el volumen de andamios ofrecidos como en sus tipos; b los andamios dados son en su totalidad indirectos y en su mayoría fijos; c los procesos que prevalecientemente se apoyan son los de la etapa de previsión y la etapa de desempeño, dejando con un andamiaje marginal los de la etapa de reflexión. Se concluye que en el programa y semestre objetos de atención la herramienta del correo electrónico es empleada en el andamiaje de la autorregulación académica en una medida, modalidad y fines susceptibles de ser mejorados. Resulta recomendable incrementar el andamiaje adaptativo, así como incluir el andamiaje a los procesos de la fase reflexiva.

Particle size and kind of mica in synthesis of nontoxic bronze and gold pearlescent pigments based on nanoencapsulated hematite

Directory of Open Access Journals (Sweden)

Maryam Hosseini-Zori

2015-12-01

Full Text Available Nano-encapsulated iron oxide in Zirconium oxide-coated mica pigments are thermally stable,innocuous to human health, non-combustible, and they do not conduct electricity. They could beapplied in several industries such as thermoplastics, cosmetics, food packaging, children toys, paints,automobiles coating, security purposes, and banknotes. Nowadays, they are highly desirable inceramic decoration. In the present study, intensively dark gold to bronze colored mica clay pigments,which were based on mica flakes covered with a layer of nano-iron oxide-Zirconium oxide particles,were prepared by homogeneous precipitation of iron nitrate and Zirconium chloride ammonia in thepresence of mica flakes in two kinds of ore clay-based phlogopite and muscovite minerals. The finalcolor was obtained by thermal annealing of precipitates at a temperature of 800◦C. The pigments werecharacterized by X-Ray Diffraction, Particle size analysis, Scanning electron microscopy,Transmission electron microscopy, X-Ray fluorescence, and Simultaneous thermal analysis. Resultsindicate that nano-encapsulated iron oxide in zirconia particles have been formed on mica flakes andkinds of clay-mica can be related to obtained shade from dark gold to bronze pearl. Higher particlesize of mica flakes about phlogopite type of mica introduced pearl effects with higher L* changes indifferent angles. Muscovite performed higher hue and better pearl effect than phlogopite.

Optimal PMU location in power systems using MICA

Directory of Open Access Journals (Sweden)

Seyed Abbas Taher

2016-03-01

Full Text Available This study presented a modified imperialist competitive algorithm (MICA for optimal placement of phasor measurement units (PMUs in normal and contingency conditions of power systems. The optimal PMU placement problem is used for full network observability with the minimum number of PMUs. For this purpose, PMUs are installed in strategic buses. Efficiency of the proposed method is shown by the simulation results of IEEE 14, 30, 57, and 118-bus test systems. Results of the numerical simulation on IEEE-test systems indicated that the proposed technique provided maximum redundancy measurement and minimum request of PMUs so that the whole system could be topologically observable by installing PMUs on the minimum system buses. To verify the proposed method, the results are compared with those of some recently reported methods. When MICA is used for solving optimal PMU placement (OPP, the number of PMUs would be usually equal to or less than those of the other existing methods. Results indicated that MICA is a very fast and accurate algorithm for OPP solution.

Biotermodin?mica en animales

OpenAIRE

Granados Moreno, Jairo Enrique

2014-01-01

El documento presenta como la termodin?mica es la ciencia que estudia las relaciones entre calor y las dem?s formas de transferencias de energ?a. Se explica que toda transformaci?n biofisicoqu?mica implica, generalmente, un cambio energ?tico. Se tratan los conceptos de temperatura, escalas de temperatura, calor, calor de combusti?n, postulados de la termodin?mica, entrop?a y energ?a libre metab?lica

Electrical bistabilities and memory mechanisms of nonvolatile organic bistable devices based on exfoliated muscovite-type mica nanoparticle/poly(methylmethacrylate) nanocomposites

Science.gov (United States)

Lim, Won Gyu; Lee, Dea Uk; Na, Han Gil; Kim, Hyoun Woo; Kim, Tae Whan

2018-02-01

Organic bistable devices (OBDs) with exfoliated mica nanoparticles (NPs) embedded into an insulating poly(methylmethacrylate) (PMMA) layer were fabricated by using a spin-coating method. Current-voltage (I-V) curves for the Al/PMMA/exfoliated mica NP/PMMA/indium-tin-oxide/glass devices at 300 K showed a clockwise current hysteresis behavior due to the existence of the exfoliated muscovite-type mica NPs, which is an essential feature for bistable devices. Write-read-erase-read data showed that the OBDs had rewritable nonvolatile memories and an endurance number of ON/OFF switching for the OBDs of 102 cycles. An ON/OFF ratio of 1 × 103 was maintained for retention times larger than 1 × 104 s. The memory mechanisms of the fabricated OBDs were described by using the trapping and the tunneling processes within a PMMA active layer containing exfoliated muscovite-type mica NPs on the basis of the energy band diagram and the I-V curves.

Measured electric field intensities near electric cloud discharges detected by the Kennedy Space Center's Lightning Detection and Ranging System, LDAR

Science.gov (United States)

Poehler, H. A.

1977-01-01

For a summer thunderstorm, for which simultaneous, airborne electric field measurements and Lightning Detection and Ranging (LDAR) System data was available, measurements were coordinated to present a picture of the electric field intensity near cloud electrical discharges detected by the LDAR System. Radar precipitation echos from NOAA's 10 cm weather radar and measured airborne electric field intensities were superimposed on LDAR PPI plots to present a coordinated data picture of thunderstorm activity.

Pulsed electric field sensor based on original waveform measurement

International Nuclear Information System (INIS)

Ma Liang; Wu Wei; Cheng Yinhui; Zhou Hui; Li Baozhong; Li Jinxi; Zhu Meng

2010-01-01

The paper introduces the differential and original waveform measurement principles for pulsed E-field, and develops an pulsed E-field sensor based on original waveform measurement along with its theoretical correction model. The sensor consists of antenna, integrator, amplifier and driver, optic-electric/electric-optic conversion module and transmission module. The time-domain calibration in TEM cell indicates that, its risetime response is shorter than 1.0 ns, and the output pulse width at 90% of the maximum amplitude is wider than 10.0 μs. The output amplitude of the sensor is linear to the electric field intensity in a dynamic range of 20 dB. The measurement capability can be extended to 10 V/m or 50 kV/m by changing the system's antenna and other relative modules. (authors)

Vector electric field measurement via position-modulated Kelvin probe force microscopy

Science.gov (United States)

Dwyer, Ryan P.; Smieska, Louisa M.; Tirmzi, Ali Moeed; Marohn, John A.

2017-10-01

High-quality spatially resolved measurements of electric fields are critical to understanding charge injection, charge transport, and charge trapping in semiconducting materials. Here, we report a variation of frequency-modulated Kelvin probe force microscopy that enables spatially resolved measurements of the electric field. We measure electric field components along multiple directions simultaneously by employing position modulation and lock-in detection in addition to numeric differentiation of the surface potential. We demonstrate the technique by recording linescans of the in-plane electric field vector in the vicinity of a patch of trapped charge in a 2,7-diphenyl[1]benzothieno[3,2-b][1]benzothiophene (DPh-BTBT) organic field-effect transistor. This technique is simple to implement and should be especially useful for studying electric fields in spatially inhomogeneous samples like organic transistors and photovoltaic blends.

Electrical measurements during magnet construction

International Nuclear Information System (INIS)

Sintchak, G.; Ganetis, G.; Cottingham, G.

1989-01-01

Throughout the construction phase of the cold mass for SSC magnets, electrical tests are made to determine that no faults in the coil structure have developed. These tests include ones designed to measure turn-to-turn voltage hold-off, hypot tests to ground, coil resistance, and instrumentation checks. These various tests will be described and the test parameters that are used will be covered. 4 figs

Evaluation of DC electric field distribution of PPLP specimen based on the measurement of electrical conductivity in LN2

International Nuclear Information System (INIS)

Hwang, Jae-Sang; Seong, Jae-Kyu; Shin, Woo-Ju; Lee, Jong-Geon; Cho, Jeon-Wook; Ryoo, Hee-Suk; Lee, Bang-Wook

2013-01-01

Highlights: •The electrical conductivity of PPLP in LN 2 was successfully measured. •Based on the measured value of PPLP, DC field analysis was performed. •The electric field distribution was altered according to the DC applying stages. •The maximum electric field was observed during polarity reversal situation. •DC field analysis is important to determine the optimum design of DC HTS devices. -- Abstract: High temperature superconducting (HTS) cable has been paid much attention due to its high efficiency and high current transportation capability, and it is also regarded as eco-friendly power cable for the next generation. Especially for DC HTS cable, it has more sustainable and stable properties compared to AC HTS cable due to the absence of AC loss in DC HTS cable. Recently, DC HTS cable has been investigated competitively all over the world, and one of the key components of DC HTS cable to be developed is a cable joint box considering HVDC environment. In order to achieve the optimum insulation design of the joint box, analysis of DC electric field distribution of the joint box is a fundamental process to develop DC HTS cable. Generally, AC electric field distribution depends on relative permittivity of dielectric materials but in case of DC, electrical conductivity of dielectric material is a dominant factor which determines electric field distribution. In this study, in order to evaluate DC electric field characteristics of the joint box for DC HTS cable, polypropylene laminated paper (PPLP) specimen has been prepared and its DC electric field distribution was analyzed based on the measurement of electrical conductivity of PPLP in liquid nitrogen (LN 2 ). Electrical conductivity of PPLP in LN 2 has not been reported yet but it should be measured for DC electric field analysis. The experimental works for measuring electrical conductivity of PPLP in LN 2 were presented in this paper. Based on the experimental works, DC electric field distribution of

A miniature sensor for electrical field measurements in dusty planetary atmospheres

International Nuclear Information System (INIS)

Renno, N O; Rogacki, S; Kok, J F; Kirkham, H

2008-01-01

Dusty phenomena such as regular wind-blown dust, dust storms, and dust devils are the most important, currently active, geological processes on Mars. Electric fields larger than 100 kV/m have been measured in terrestrial dusty phenomena. Theoretical calculations predict that, close to the surface, the bulk electric fields in martian dusty phenomena reach the breakdown value of the isolating properties of thin martian air of about a few 10 kV/m. The fact that martian dusty phenomena are electrically active has important implications for dust lifting and atmospheric chemistry. Electric field sensors are usually grounded and distort the electric fields in their vicinity. Grounded sensors also produce large errors when subject to ion currents or impacts from clouds of charged particles. Moreover, they are incapable of providing information about the direction of the electric field, an important quantity. Finally, typical sensors with more than 10 cm of diameter are not capable of measuring electric fields at distances as small as a few cm from the surface. Measurements this close to the surface are necessary for studies of the effects of electric fields on dust lifting. To overcome these shortcomings, we developed the miniature electric-field sensor described in this article.

Coulomb's Electrical Measurements. Experiment No. 14.

Science.gov (United States)

Devons, Samuel

Presented is information related to the life and work of Charles Coulomb as well as detailed notes of his measurements of the distribution of electricity on conductors. The two methods that he used (the large torsion balance, and the timing of "force" oscillations) are described. (SA)

Geo-electric measurements – internal state of historic masonry

OpenAIRE

Schueremans, Luc

2009-01-01

A geophysical resistivity measuring device was modified to perform automatic monitoring of historical masonry structures before, during and after grout injection for consolidation purposes. The obtained image is called a geo-electrical tomography. The technique was used to evaluate the deteriorated masonry of the recently partly collapsed Maagdentoren in Zichem,(B). Geo-electric measuring techniques have been adapted from application in geology to be used as a non-destructive technique for t...

Electrical conductivity measurement on DKDP Crystals with different deuterated degrees

International Nuclear Information System (INIS)

Liu, Baoan; Yin, Xin; Xu, Mingxia; Ji, Shaohua; Zhu, Lili; Zhang, Lisong; Sun, Xun; Xu, Xinguang; Zhao, Minglei; Zhang, Qinghua

2012-01-01

Ten DKDP single crystals with deuterated degrees ranging from 0 to 90 % were grown by a rapid growth method. The electrical conductivities of these crystals were measured along a and c directions at room temperature. The electrical conductivity increases with the increase for deuterium content. Also, the electrical conductivities of certain crystals were measured at various temperatures ranging from 20 to 130 C. The values of activation energy decrease as the increase of deuterium content. The present study indicates that the deuterium tunneling frequency is smaller than that of hydrogen, which may be the reason why the variation of electrical conductivity happens after the substitution of hydrogen for deuterium in KDP crystal. (orig.)

PHASE GRADIENT METHOD OF MAGNETIC FIELD MEASUREMENTS IN ELECTRIC VEHICLES

Directory of Open Access Journals (Sweden)

N. G. Ptitsyna

2013-01-01

Full Text Available Operation of electric and hybrid vehicles demands real time magnetic field control, for instance, for fire and electromagnetic safety. The article deals with a method of magnetic field measurements onboard electric cars taking into account peculiar features of these fields. The method is based on differential methods of measurements, and minimizes the quantity of magnetic sensors.

The nanostructure formation on muscovite mica surface induced by intermediate-energy ions

Energy Technology Data Exchange (ETDEWEB)

Zhou, P.; Zhang, HQ., E-mail: zhanghq@lzu.edu.cn; Zhang, Q.; Liu, Z.; Guan, S.; Wang, G.; Zhou, C.; Jia, J.; Lv, X.; Shao, J.; Cui, Y.; Chen, L.; Chen, X., E-mail: chenxm@lzu.edu.cn

2013-07-15

Muscovite mica sheets were bombarded by lithium, carbon and oxygen ions in the energy range from several hundred keV to several MeV. The induced surface structures were measured in the air with atomic force microscopy (AFM) in the tapping mode. The hillock-like structure on the mica surface was observed. The height of the hillock increases linearly when the energy loss is above 1.2 keV/nm. The induced structures are similar with the similar electronic stopping powers but different projectiles for muscovite mica.

Development of electrical efficiency measurement techniques for 10 kW-class SOFC system: Part I. Measurement of electrical efficiency

International Nuclear Information System (INIS)

Tanaka, Yohei; Momma, Akihiko; Kato, Ken; Negishi, Akira; Takano, Kiyonami; Nozaki, Ken; Kato, Tohru

2009-01-01

Measurement techniques to estimate electrical efficiency of 10 kW-class SOFC systems fueled by town-gas were developed and demonstrated for a system developed by Kansai Electric Power Company and Mitsubishi Materials Corporation under a NEDO project. Higher heating value of the fuel was evaluated with a transportable gas sampling unit and conventional gas chromatography in AIST laboratory with thermal-conductivity and flame-ionization detectors, leading to mean value 44.69 MJ m -3 on a volumetric base for ideal-gas at the standard state (0 deg. C, 101.325 kPa). Mass-flow-rate of the fuel was estimated as 33.04 slm with a mass-flow meter for CH 4 , which was calibrated to correct CH 4 flow-rate and effect of sensitivity change and to obtain conversion factor from CH 4 to town-gas. Without calibration, systematic effect would occur by 8% in flow-rate measurement in the case for CH 4 . Power output was measured with a precision power analyzer, a virtual three phase starpoint adapter, and tri-axial shunts. Power of fundamental wave (60 Hz) was estimated as 10.14 kW, considering from total active power, total higher harmonic distortion factor, and power consumption at the starpoint adapter. The electrical efficiency was presumed to be 41.2% (HHV), though this mean value will be complete only when uncertainty estimation is accompanied

Electric field simulation and measurement of a pulse line ion accelerator

International Nuclear Information System (INIS)

Shen Xiaokang; Zhang Zimin; Cao Shuchun; Zhao Hongwei; Zhao Quantang; Liu Ming; Jing Yi; Wang Bo; Shen Xiaoli

2012-01-01

An oil dielectric helical pulse line to demonstrate the principles of a Pulse Line Ion Accelerator (PLIA) has been designed and fabricated. The simulation of the axial electric field of an accelerator with CST code has been completed and the simulation results show complete agreement with the theoretical calculations. To fully understand the real value of the electric field excited from the helical line in PLIA, an optical electric integrated electric field measurement system was adopted. The measurement result shows that the real magnitude of axial electric field is smaller than that calculated, probably due to the actual pitch of the resister column which is much less than that of helix. (authors)

Influence of the nonexchangeable potassium of mica on radiocesium uptake by paddy rice

International Nuclear Information System (INIS)

Eguchi, Tetsuya; Ohta, Takeshi; Ishikawa, Tetsuya; Matsunami, Hisaya; Takahashi, Yoshihiko; Kubo, Katashi; Yamaguchi, Noriko; Kihou, Nobuharu; Shinano, Takuro

2015-01-01

A pot cultivation experiment was conducted to elucidate the influence of the nonexchangeable potassium (K) of mica on radiocesium ( 137 Cs) uptake by paddy rice (Oryza sativa L. cv. Koshihikari), and to evaluate the potential of mica application as a countermeasure to reduce radiocesium transfer from soil to paddy rice. The increase in the exchangeable K concentrations of soils, measured before planting, due to mica (muscovite, biotite, and phlogopite) application was negligible. However, in trioctahedral mica (biotite and phlogopite)-treated soil, the release of nonexchangeable K from the mica interlayer maintained the soil-solution K at a higher level during the growing season in comparison to the control, and consequently decreased the 137 Cs transfer factor for brown rice (TF). The sodium tetraphenylboron (TPB)-extractable K concentration of the soils, measured before planting, was strongly negatively correlated with the TF, whereas the exchangeable K concentration of the soils, also measured before planting, was not correlated with the TF. Therefore, we conclude that TPB-extractable K is more reliable than exchangeable K as a basis of fertilizer recommendations for radiocesium-contaminated paddy fields. Phlogopite-treated soils exhibited higher TPB-extractable K concentrations and lower TF values than biotite-treated soils. We thus conclude that phlogopite application is an effective countermeasure to reduce radiocesium uptake in paddy rice. - Highlights: • Nonexchangeable K of added trioctahedral mica decreased 137 Cs uptake by paddy rice. • TPB-extractable K would be a more reliable indicator than exchangeable K. • Phlogopite would be a good amendment for radiocesium-contaminated paddy fields

Electrical resistivity measurements to predict abrasion resistance

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 31; Issue 2. Electrical resistivity measurements to predict abrasion resistance of rock aggregates ... It was seen that correlation coefficients were increased for the rock classes. In addition ...

Factores de riesgo de la cardiopatía isquémica

Directory of Open Access Journals (Sweden)

Liliam Gretel Cisneros Sánchez

Full Text Available Introducción: la enfermedad arterial coronaria es una de las principales causas de mortalidad en todo el mundo. En su fisiopatología juega un papel importante el desarrollo y la progresión de la aterosclerosis coronaria, la cual está íntimamente relacionada con determinados hábitos de vida y ciertas características personales que se conocen como factores de riesgo. Objetivo: actualizar a los profesionales delaAtenciónPrimaria de Salud sobre los factores de riesgo de la Cardiopatía Isquémica. Métodos: se realizó una revisión bibliográfica en libros de Medicina y artículos científicos disponibles en revistas digitales, a través de buscadores de información. Se accedió a diferentes fuentes de información como bases de datos, libros electrónicos, revistas electrónicas, etcétera, de infomed e internet. Luego se hizo un análisis crítico sobre el tema, avalado por la en contrado en la literatura consultada. Desarrollo: la situación de las enfermedades cardiovascularesen el mundo ha pasado por distintas fases, en correspondencia con el desarrollo socioeconómico de los países y el aumento en la incidencia de los distintos factores de riesgo, los cuales influyen de manera diferente en la aparición de la Cardiopatía Isquémica. Conclusiones: es importante conocer la influencia de cada factor de riesgo cardiovascular en la aparición de la Cardiopatía Isquémica para tomar estrategias encaminadas al control de los mismos y evitar llegar a la enfermedad.

Optical sensors for the measurement of electric current and voltage

Energy Technology Data Exchange (ETDEWEB)

Rutgers, W R; Hulshof, H J.M.; Laurensse, I J; van der Wey, A H

1987-01-01

Optical sensors for the measurement of electrical current and voltage were developed for application in electric power systems. The current sensor, based on the Faraday effect in a monomode glass fiber, and the voltage sensor, based on the transverse Pockels effect in a crystal, are demonstrated in wide-band (10 MHz) interference-free measurements of pulsed currents and impulse voltages.

Evaluation of DC electric field distribution of PPLP specimen based on the measurement of electrical conductivity in LN{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Hwang, Jae-Sang; Seong, Jae-Kyu; Shin, Woo-Ju; Lee, Jong-Geon [Hanyang University, 408-2, 4th Engineering Bldg, Sa 3-dong, Sangrok-gu, Ansan 426-791 (Korea, Republic of); Cho, Jeon-Wook; Ryoo, Hee-Suk [Korea Electrotechnology Research Institute, Changwon, Gyungnam 641-120 (Korea, Republic of); Lee, Bang-Wook, E-mail: bangwook@hanyang.ac.kr [Hanyang University, 408-2, 4th Engineering Bldg, Sa 3-dong, Sangrok-gu, Ansan 426-791 (Korea, Republic of)

2013-11-15

Highlights: •The electrical conductivity of PPLP in LN{sub 2} was successfully measured. •Based on the measured value of PPLP, DC field analysis was performed. •The electric field distribution was altered according to the DC applying stages. •The maximum electric field was observed during polarity reversal situation. •DC field analysis is important to determine the optimum design of DC HTS devices. -- Abstract: High temperature superconducting (HTS) cable has been paid much attention due to its high efficiency and high current transportation capability, and it is also regarded as eco-friendly power cable for the next generation. Especially for DC HTS cable, it has more sustainable and stable properties compared to AC HTS cable due to the absence of AC loss in DC HTS cable. Recently, DC HTS cable has been investigated competitively all over the world, and one of the key components of DC HTS cable to be developed is a cable joint box considering HVDC environment. In order to achieve the optimum insulation design of the joint box, analysis of DC electric field distribution of the joint box is a fundamental process to develop DC HTS cable. Generally, AC electric field distribution depends on relative permittivity of dielectric materials but in case of DC, electrical conductivity of dielectric material is a dominant factor which determines electric field distribution. In this study, in order to evaluate DC electric field characteristics of the joint box for DC HTS cable, polypropylene laminated paper (PPLP) specimen has been prepared and its DC electric field distribution was analyzed based on the measurement of electrical conductivity of PPLP in liquid nitrogen (LN{sub 2}). Electrical conductivity of PPLP in LN{sub 2} has not been reported yet but it should be measured for DC electric field analysis. The experimental works for measuring electrical conductivity of PPLP in LN{sub 2} were presented in this paper. Based on the experimental works, DC electric

Influence of the nonexchangeable potassium of mica on radiocesium uptake by paddy rice.

Science.gov (United States)

Eguchi, Tetsuya; Ohta, Takeshi; Ishikawa, Tetsuya; Matsunami, Hisaya; Takahashi, Yoshihiko; Kubo, Katashi; Yamaguchi, Noriko; Kihou, Nobuharu; Shinano, Takuro

2015-09-01

A pot cultivation experiment was conducted to elucidate the influence of the nonexchangeable potassium (K) of mica on radiocesium ((137)Cs) uptake by paddy rice (Oryza sativa L. cv. Koshihikari), and to evaluate the potential of mica application as a countermeasure to reduce radiocesium transfer from soil to paddy rice. The increase in the exchangeable K concentrations of soils, measured before planting, due to mica (muscovite, biotite, and phlogopite) application was negligible. However, in trioctahedral mica (biotite and phlogopite)-treated soil, the release of nonexchangeable K from the mica interlayer maintained the soil-solution K at a higher level during the growing season in comparison to the control, and consequently decreased the (137)Cs transfer factor for brown rice (TF). The sodium tetraphenylboron (TPB)-extractable K concentration of the soils, measured before planting, was strongly negatively correlated with the TF, whereas the exchangeable K concentration of the soils, also measured before planting, was not correlated with the TF. Therefore, we conclude that TPB-extractable K is more reliable than exchangeable K as a basis of fertilizer recommendations for radiocesium-contaminated paddy fields. Phlogopite-treated soils exhibited higher TPB-extractable K concentrations and lower TF values than biotite-treated soils. We thus conclude that phlogopite application is an effective countermeasure to reduce radiocesium uptake in paddy rice. Copyright © 2015 Elsevier Ltd. All rights reserved.

Simulation of Light Collection for Neutron Electrical Dipole Moment measurement

Science.gov (United States)

Ji, Pan; nEDM Collaboration

2017-09-01

nEDM (Neutron Electrical Dipole moment) measurement addresses a critical topic in particle physics and Standard Model, that is CPT violation in neutron electrical dipole moment if detected in which the Time reversal violation is connected to the matter/antimatter imparity of the universe. The neutron electric dipole moment was first measured in 1950 by Smith, Purcell, and Ramsey at the Oak Ridge Reactor - the first intense neutron source. This measurement showed that the neutron was very nearly round (to better than one part in a million). The goal of the nEDM experiment is to further improve the precision of this measurement by another factor of 100. The signal from the experiment is detected by collecting the photons generated when neutron beams were captured by liquid helium 3. The Geant4 simulation project that I participate simulates the process of light collection to improve the design for higher capture efficiency. The simulated geometry includes light source, reflector, wavelength shifting fibers, wavelength shifting TPB and acrylic as in real experiment. The UV photons exiting from Helium go through two wavelength-shifting processes in TPB and fibers to be finally captured. Oak Ridge National Laboratory Neutron Electric Dipole Moment measurement project.

Growth of highly textured SnS on mica using an SnSe buffer layer

International Nuclear Information System (INIS)

Wang, S.F.; Fong, W.K.; Wang, W.; Surya, C.

2014-01-01

We report the growth of SnS thin films on mica substrates by molecular beam epitaxy. Excellent 2D layered structure and strong (001) texture were observed with a record low rocking curve full width at half maximum of ∼ 0.101° for the SnS(004) diffraction. An interface model is used to investigate the nucleation of SnS on mica which indicates the co-existence of six pairs of lateral growth orientations and is in excellent agreement with the experimental Φ-scan measurements indicating 12 peaks separated by 30° from each other. To control the lateral growth of the SnS epilayers we investigate the utilization of a thin SnSe buffer layer deposited on the mica substrate prior to the growth of the SnS thin film. The excellent lattice match between SnSe and mica enhances the alignment of the nucleation of SnS and suppresses the minor lateral orientations along the mica[110] direction and its orthogonal axis. Detailed low-frequency noise measurement was performed to characterize the trap density in the films and our results clearly demonstrate substantial reduction in the density of the localized states in the SnS epilayer with the use of an SnSe buffer layer. - Highlights: • A record low rocking curve FWHM for deposited SnS on mica • Investigation of the nucleation of SnS on mica using the interface model • Investigation of nucleation mechanism by phi-scan measurement • Grain boundary formation from crystallites of various nucleation orientations • Suppression of nucleation orientations using an SnSe buffer layer

Electric field measurements in a near atmospheric pressure nanosecond pulse discharge with picosecond electric field induced second harmonic generation

Science.gov (United States)

Goldberg, Benjamin M.; Chng, Tat Loon; Dogariu, Arthur; Miles, Richard B.

2018-02-01

We present an optical electric field measurement method for use in high pressure plasma discharges. The method is based upon the field induced second harmonic generation technique and can be used for localized electric field measurements with sub-nanosecond resolution in any gaseous species. When an external electric field is present, a dipole is induced in the typically centrosymmetric medium, allowing for second harmonic generation with signal intensities which scale by the square of the electric field. Calibrations have been carried out in 100 Torr room air, and a minimum sensitivity of 450 V/cm is demonstrated. Measurements were performed with nanosecond or faster temporal resolution in a 100 Torr room air environment both with and without a plasma present. It was shown that with no plasma present, the field follows the applied voltage to gap ratio, as measured using the back current shunt method. When the electric field is strong enough to exceed the breakdown threshold, the measured field was shown to exceed the anticipated voltage to gap ratio which is taken as an indication of the ionization wave front as it sweeps through the plasma volume.

Incoherent-scatter radar measurements of electric field and plasma in the auroral ionosphere

International Nuclear Information System (INIS)

Vondrak, R.

1983-01-01

This chapter summarizes Chatanika radar measurements of electric fields and currents, and their relation to E-region ionization and conductivity. Electric-field coupling between the ionosphere and magnetosphere and the relationship between field-aligned currents and meridional ionospheric currents are examined. Topics considered include the diurnal pattern of the ionization and electric field; electrical coupling between the ionosphere and magnetosphere; and the relationship between meridional currents and field-aligned currents. It is concluded that the incoherent-scatter radar technique has been developed into a powerful method for remotely measuring the electrical and thermal properties of the auroral ionospheric plasma, and that the usefulness of the radar measurements is greatly enhanced when combined with simultaneous satellite measurements

Measurement of power loss during electric vehicle charging and discharging

International Nuclear Information System (INIS)

Apostolaki-Iosifidou, Elpiniki; Codani, Paul; Kempton, Willett

2017-01-01

When charging or discharging electric vehicles, power losses occur in the vehicle and the building systems supplying the vehicle. A new use case for electric vehicles, grid services, has recently begun commercial operation. Vehicles capable of such application, called Grid-Integrated Vehicles, may have use cases with charging and discharging summing up to much more energy transfer than the charging only use case, so measuring and reducing electrical losses is even more important. In this study, the authors experimentally measure and analyze the power losses of a Grid-Integrated Vehicle system, via detailed measurement of the building circuits, power feed components, and of sample electric vehicle components. Under the conditions studied, measured total one-way losses vary from 12% to 36%, so understanding loss factors is important to efficient design and use. Predominant losses occur in the power electronics used for AC-DC conversion. The electronics efficiency is lowest at low power transfer and low state-of-charge, and is lower during discharging than charging. Based on these findings, two engineering design approaches are proposed. First, optimal sizing of charging stations is analyzed. Second, a dispatch algorithm for grid services operating at highest efficiency is developed, showing 7.0% to 9.7% less losses than the simple equal dispatch algorithm. - Highlights: • Grid-to-battery-to-grid comprehensive power loss measurement and analysis. • No previous experimental measurements of Grid-Integrated Vehicle system power loss. • Electric vehicle loss analyzed as a factor of state of charge and charging rate. • Power loss in the building components less than 3%. • Largest losses found in Power Electronics (typical round-trip loss 20%).

Information-Measuring System to Control the Electrical and Mechanical Motor Parameters

Directory of Open Access Journals (Sweden)

K. S. Ermakov

2015-01-01

Full Text Available The article considers the issue of creating an information-measuring system for an asynchronous motor. The presented system allows ensuring the failure-free protection of electromotor, considerably reducing costs of its unplanned repair, and reduced economical loss from idle time of the electric motor.The developed system comprises a mathematical model and two subsystems to measure electrical and mechanical parameters of the asynchronous motor.The electrical subsystem comprises a FLUKE company recording multi-meter a signal from which passes through the block of intervals and coding and comes to PC.The mechanical subsystem uses technical tools of phase-chronometric method. This method developed at the department of Metrology and Interchangeability allows an increasing efficiency of developed informative-measuring system. Mathematical modeling is used to link information from subsystems (electrical and mechanical to electromotor construction.The work conducted mathematical modeling of some defects of electric motor, namely: rupture of rotor winding and line surge.The mathematical model in Mathcad was based on a modified formula of Kloss. It allows us to tie the average current value of the torque of the induction motor with shaft speed and take into account the effect of the frequency and voltage.The Matlab Simulink (the package for visual programming environment was used to simulate a rupture of the rotor winding. Simulation results showed how the phase currents of the electric motor changed with the winding rupture.The developed information-measuring system has a number of advantages over traditional systems used in this field (vibration-based diagnostics systems. It will allow an increasing efficiency of the system for diagnostics of electrical machines created on the basis of this information-measuring system.

Noninvasive electrical conductivity measurement by MRI: a test of its validity and the electrical conductivity characteristics of glioma.

Science.gov (United States)

Tha, Khin Khin; Katscher, Ulrich; Yamaguchi, Shigeru; Stehning, Christian; Terasaka, Shunsuke; Fujima, Noriyuki; Kudo, Kohsuke; Kazumata, Ken; Yamamoto, Toru; Van Cauteren, Marc; Shirato, Hiroki

2018-01-01

This study noninvasively examined the electrical conductivity (σ) characteristics of diffuse gliomas using MRI and tested its validity. MRI including a 3D steady-state free precession (3D SSFP) sequence was performed on 30 glioma patients. The σ maps were reconstructed from the phase images of the 3D SSFP sequence. The σ histogram metrics were extracted and compared among the contrast-enhanced (CET) and noncontrast-enhanced tumour components (NCET) and normal brain parenchyma (NP). Difference in tumour σ histogram metrics among tumour grades and correlation of σ metrics with tumour grades were tested. Validity of σ measurement using this technique was tested by correlating the mean tumour σ values measured using MRI with those measured ex vivo using a dielectric probe. Several σ histogram metrics of CET and NCET of diffuse gliomas were significantly higher than NP (Bonferroni-corrected p ≤ .045). The maximum σ of NCET showed a moderate positive correlation with tumour grade (r = .571, Bonferroni-corrected p = .018). The mean tumour σ measured using MRI showed a moderate positive correlation with the σ measured ex vivo (r = .518, p = .040). Tissue σ can be evaluated using MRI, incorporation of which may better characterise diffuse gliomas. • This study tested the validity of noninvasive electrical conductivity measurements by MRI. • This study also evaluated the electrical conductivity characteristics of diffuse glioma. • Gliomas have higher electrical conductivity values than the normal brain parenchyma. • Noninvasive electrical conductivity measurement can be helpful for better characterisation of glioma.

Measurements of electrically exploded tubes

International Nuclear Information System (INIS)

Shearer, J.W.; Hartman, C.W.; Munger, R.H.; Gullickson, R.L.; Trimble, D.O.; Cheng, D.Y.

1975-01-01

The dynamics of electrically exploded tubes were investigated, principally by means of current measurements and flash x-ray pictures. The pinch effect was observed on the tube motion. Pileup of the imploding tube metal was seen on axis. An approximate analytical model can be roughly fitted to the data, but a more complete fit can be obtained with detailed numerical codes. Application of the results to the planning of future gas-embedded Z-pinch experiments is discussed. (U.S.)

RF Characteristics of Mica-Z Wireless Sensor Network Motes

National Research Council Canada - National Science Library

Koh, Swee J

2006-01-01

... network characteristics. Link-break and re-association distances with their corresponding RF power measurements were recorded to determine the Mica-Z s range characteristics under these different operating environments...

Electrical resistivity measurement to predict uniaxial compressive ...

Indian Academy of Sciences (India)

Electrical resistivity values of 12 different igneous rocks were measured on core samples using a resistivity meter in the ... It was seen that the UCS and tensile strength values were linearly correlated with the ..... Innovation 2 20. Archie G E ...

Electric field measurement in microwave discharge ion thruster with electro-optic probe.

Science.gov (United States)

Ise, Toshiyuki; Tsukizaki, Ryudo; Togo, Hiroyoshi; Koizumi, Hiroyuki; Kuninaka, Hitoshi

2012-12-01

In order to understand the internal phenomena in a microwave discharge ion thruster, it is important to measure the distribution of the microwave electric field inside the discharge chamber, which is directly related to the plasma production. In this study, we proposed a novel method of measuring a microwave electric field with an electro-optic (EO) probe based on the Pockels effect. The probe, including a cooling system, contains no metal and can be accessed in the discharge chamber with less disruption to the microwave distribution. This method enables measurement of the electric field profile under ion beam acceleration. We first verified the measurement with the EO probe by a comparison with a finite-difference time domain numerical simulation of the microwave electric field in atmosphere. Second, we showed that the deviations of the reflected microwave power and the beam current were less than 8% due to inserting the EO probe into the ion thruster under ion beam acceleration. Finally, we successfully demonstrated the measurement of the electric-field profile in the ion thruster under ion beam acceleration. These measurements show that the electric field distribution in the thruster dramatically changes in the ion thruster under ion beam acceleration as the propellant mass flow rate increases. These results indicate that this new method using an EO probe can provide a useful guide for improving the propulsion of microwave discharge ion thrusters.

Electric field measurement in the ionosphere using the time-of-flight technique

International Nuclear Information System (INIS)

Nakamura, Masato; Hayakawa, Hajime; Tsuruda, Koichiro

1989-01-01

The first successful electric field measurement in the ionosphere using the time-of-flight technique with a lithium ion beam was carried out on a S-520 sounding rocket launched from Kagoshima Space Center, Japan on January 15, 1987. The purpose of this experiment was to prove the validity of the time-of-flight technique when it is applied to the measurement of the dc electric field in the ionosphere. A time-coded ion beam was ejected from the rocket in the direction perpendicular to the Earth's magnetic field. The beam returned to the rocket twice per rocket spin when the initial beam direction was nearly perpendicular to the electric field. The electric field and the magnetic field were derived from the travel time of these return lithium ions. The accuracy of the electric field determination was ± 0.3 mV/m. The direction of the electric field was obtained from the direction of the returning ion beam after about one ion gyration. The main constituent of the measured electric field was a V x B field due to the rocket motion across the geomagnetic field. The ambient field was less than 1 mV/m. The magnetic field was measured with an accuracy of ± 2.7 nT in this experiment

An Analysis of Ionospheric Thermal Ions Using a SIMION-based Forward Instrument Model: In Situ Observations of Vertical Thermal Ion Flows as Measured by the MICA Sounding Rocket

Science.gov (United States)

Fernandes, P. A.; Lynch, K. A.; Zettergren, M. D.; Hampton, D. L.; Fisher, L. E.; Powell, S. P.

2013-12-01

created with the Spacecraft Plasma Interaction Software (SPIS). Once we have coupled the instrument and forward models to this sophisticated sheath model, we can rigorously extract the properties of the background thermal plasma. These thermal plasma measurements are used to address questions of ionospheric-thermospheric coupling. These questions for MICA and its modeling efforts include the following: is the state of the ionosphere during the rocket flight a remnant of the westward traveling surge, or is it a direct response to localized drivers? How do the calculated ion flows compare to the flows derived from the electric field data, and what do these flows tell us about the state of the ionosphere? How do the MICA measurements of ion upflows and downflows tie into the broader sounding rocket ion parallel flow study presented by Lynch et al. (this session) and into the Zettergren and Semeter, [2012] 2D, ionospheric fluid/electrostatic model?

The future of GPS-based electric power system measurements, operation and control

Energy Technology Data Exchange (ETDEWEB)

Rizy, D.T. [Oak Ridge National Lab., TN (United States); Wilson, R.E. [Western Area Power Administration, Golden, CO (United States); Martin, K.E.; Litzenberger, W.H. [Bonneville Power Administration, Portland, OR (United States); Hauer, J.F. [Pacific Northwest National Lab., Richland, WA (United States); Overholt, P.N. [Dept. of Energy, Washington, DC (United States); Sobajic, D.J. [Electric Power Research Inst., Palo Alto, CA (United States)

1998-11-01

Much of modern society is powered by inexpensive and reliable electricity delivered by a complex and elaborate electric power network. Electrical utilities are currently using the Global Positioning System-NAVSTAR (GPS) timekeeping to improve the network`s reliability. Currently, GPS synchronizes the clocks on dynamic recorders and aids in post-mortem analysis of network disturbances. Two major projects have demonstrated the use of GPS-synchronized power system measurements. In 1992, the Electric Power Research Institute`s (EPRI) sponsored Phase Measurements Project used a commercially available Phasor Measurements Unit (PMU) to collect GPS-synchronized measurements for analyzing power system problems. In 1995, Bonneville Power Administration (BPA) and Western Area Power Administration (WAPA) under DOE`s and EPRI`s sponsorship launched the Wide Area Measurements (WAMS) project. WAMS demonstrated GPS-synchronized measurements over a large area of their power networks and demonstrated the networking of GPS-based measurement systems in BPA and WAPA. The phasor measurement technology has also been used to conduct dynamic power system tests. During these tests, a large dynamic resistor was inserted to simulate a small power system disturbance.

Detecting rapid mass movements using electrical self-potential measurements

Science.gov (United States)

Heinze, Thomas; Limbrock, Jonas; Pudasaini, Shiva P.; Kemna, Andreas

2017-04-01

Rapid mass movements are a latent danger for lives and infrastructure in almost any part of the world. Often such mass movements are caused by increasing pore pressure, for example, landslides after heavy rainfall or dam breaking after intrusion of water in the dam. Among several other geophysical methods used to observe water movement, the electrical self-potential method has been applied to a broad range of monitoring studies, especially focusing on volcanism and dam leakage but also during hydraulic fracturing and for earthquake prediction. Electrical self-potential signals may be caused by various mechanisms. Though, the most relevant source of the self-potential field in the given context is the streaming potential, caused by a flowing electrolyte through porous media with electrically charged internal surfaces. So far, existing models focus on monitoring water flow in non-deformable porous media. However, as the self-potential is sensitive to hydraulic parameters of the soil, any change in these parameters will cause an alteration of the electric signal. Mass movement will significantly influence the hydraulic parameters of the solid as well as the pressure field, assuming that fluid movement is faster than the pressure diffusion. We will present results of laboratory experiments under drained and undrained conditions with fluid triggered as well as manually triggered mass movements, monitored with self-potential measurements. For the undrained scenarios, we observe a clear correlation between the mass movements and signals in the electric potential, which clearly differ from the underlying potential variations due to increased saturation and fluid flow. In the drained experiments, we do not observe any measurable change in the electric potential. We therefore assume that change in fluid properties and release of the load causes disturbances in flow and streaming potential. We will discuss results of numerical simulations reproducing the observed effect. Our

Measurement of temperature, electric conductivity and density of plasma

International Nuclear Information System (INIS)

Vasilevova, I.; Nefedov, A.; Oberman, F.; Urinson, A.

1982-01-01

Three instruments are briefly described developed by the High Temperatures Institute of the USSR Academy of Sciences for the measurement of plasma temperature, electric conductivity and density. The temperature measuring instrument uses as a standard a light source whose temperature may significantly differ from plasma temperature because three light fluxes are compared, namely the flux emitted by the plasma, the flux emitted directly by the standard source, and the flux emitted by the standard source after passage through the plasma. The results of measurement are computer processed. Electric conductivity is measured using a coil placed in a probe which is automatically extended for a time of maximally 0.3 seconds into the plasma stream. The equipment for measuring plasma density consists of a special single-channel monochromator, a temperature gauge, a plasma pressure gauge, and of a computer for processing the results of measurement. (Ha)

Equipment for the measurement of non-electrical parameters

International Nuclear Information System (INIS)

Lewin, M.I.; Ewtuchow, A.N.

1977-01-01

The invention concerns equipment for the measurement of non-electrical parameters, which can be used in data processing and control equipment. The transducer converts non-electrical parameters into electrical signals. The process according to the invention is explained using the example of an inductive transducer, which is fed with alternating current. The measured parameter affects the mutual inductance of the transducer, so that the secondary voltage supplied by it is a function of the measured parameter. Amplitude measurement of this voltage by means of rectification and filtering has the disadvantage of long time constants, where the measuring period would amount to 6 to 10 cycles of the supply voltage. According to the invention the secondary voltage of the transducer is connected to an integrator during a half-cycle between two zeros, which charges a capacitor to a voltage proportional to the amplitude. An analogue-digital converter now produces a digital signal corresponding to the capacitor voltage, which is taken to the control equipment. This conversion occurs during a fraction of the second half-cycle, so that there is still time before the end of this half-cycle, so that there is still time before the end of this half-cycle to discharge the capacitor and to reproduce the initial conditions. In the next cycle the whole process is repeated, so that the measuring process only takes one cycle. In order to make the digital signal independent of the amplitude of the current fed in, this also flows through an identical transducer with constant mutual inductance, and affects the analogue-digital converter via a comparative circuit. (ORU) [de

Evaluation of DC electric field distribution of PPLP specimen based on the measurement of electrical conductivity in LN2

Science.gov (United States)

Hwang, Jae-Sang; Seong, Jae-Kyu; Shin, Woo-Ju; Lee, Jong-Geon; Cho, Jeon-Wook; Ryoo, Hee-Suk; Lee, Bang-Wook

2013-11-01

High temperature superconducting (HTS) cable has been paid much attention due to its high efficiency and high current transportation capability, and it is also regarded as eco-friendly power cable for the next generation. Especially for DC HTS cable, it has more sustainable and stable properties compared to AC HTS cable due to the absence of AC loss in DC HTS cable. Recently, DC HTS cable has been investigated competitively all over the world, and one of the key components of DC HTS cable to be developed is a cable joint box considering HVDC environment. In order to achieve the optimum insulation design of the joint box, analysis of DC electric field distribution of the joint box is a fundamental process to develop DC HTS cable. Generally, AC electric field distribution depends on relative permittivity of dielectric materials but in case of DC, electrical conductivity of dielectric material is a dominant factor which determines electric field distribution. In this study, in order to evaluate DC electric field characteristics of the joint box for DC HTS cable, polypropylene laminated paper (PPLP) specimen has been prepared and its DC electric field distribution was analyzed based on the measurement of electrical conductivity of PPLP in liquid nitrogen (LN2). Electrical conductivity of PPLP in LN2 has not been reported yet but it should be measured for DC electric field analysis. The experimental works for measuring electrical conductivity of PPLP in LN2 were presented in this paper. Based on the experimental works, DC electric field distribution of PPLP specimen was fully analyzed considering the steady state and the transient state of DC. Consequently, it was possible to determine the electric field distribution characteristics considering different DC applying stages including DC switching on, DC switching off and polarity reversal conditions.

A microwave inverse Cerenkov Accelerator (MICA)

International Nuclear Information System (INIS)

Hirshfield, Jay L.

1999-01-01

The objective of this Phase II SBIR research program was to complete the final design originated during Phase I for a prototype Microwave Inverse Cerenkov Accelerator (MICA), to fabricate the-prototype MICA, and to test its performance as an electron accelerator. This report contains details of the design, predictions of accelerator performance, results of cold tests on the MICA structure, and details of the installation of MICA on the Yale Beam Physics Laboratory 6-MeV beamline. Discussion of future work is also included

Electric shock and electrical fire specialty

International Nuclear Information System (INIS)

2011-02-01

This book deals with electric shock and electrical fire, which is made up seven chapters. It describes of special measurement for electric shock and electrical fire. It mentions concretely about electrical fire analysis and precautionary measurement, electrical shock analysis cases, occurrence of static electricity and measurement, gas accident, analysis of equipment accident and precautionary measurement. The book is published to educate the measurement on electric shock and electrical fire by electrical safety technology education center in Korea Electrical Safety Corporation.

Effect of Voltage Measurement on the Quantitative Identification of Transverse Cracks by Electrical Measurements

KAUST Repository

Selvakumaran, Lakshmi; Lubineau, Gilles

2016-01-01

of the ply. Through the mesoscale relationship, the conductivity obtained from electrical tomography can be used as a measure of the transverse cracking density. Interpretation of this measure will be accurate provided the assumptions made during

Leaching of Conductive Species: Implications to Measurements of Electrical Resistivity.

Science.gov (United States)

Spragg, R; Jones, S; Bu, Y; Lu, Y; Bentz, D; Snyder, K; Weiss, J

2017-05-01

Electrical tests have been used to characterize the microstructure of porous materials, the measured electrical response being determined by the contribution of the microstructure (porosity and tortuosity) and the electrical properties of the solution (conductivity of the pore solution) inside the pores of the material. This study has shown how differences in concentration between the pore solution (i.e., the solution in the pores) and the storage solution surrounding the test specimen leads to significant transport (leaching) of the conductive ionic species between the pore solution and the storage solution. Leaching influences the resistivity of the pore solution, thereby influencing electrical measurements on the bulk material from either a surface or uniaxial bulk resistance test. This paper has three main conclusions: 1.) Leaching of conductive species does occur with concentration gradients and that a diffusion based approach can be used to estimate the time scale associated with this change. 2.) Leaching of ions in the pore solution can influence resistivity measurements, and the ratio of surface to uniaxial resistivity can be used as a method to assess the presence of leaching and 3.) An estimation of the magnitude of leaching for standardized tests of cementitious materials.

Performance measurement of electricity suppliers using PROMETHEE and balance scorecard

OpenAIRE

Mona Osati; Manouchehr Omidvari

2016-01-01

Performance measurement in energy industry plays an important role on increasing the productivity. Electricity is also among the most essential components of energy in mega cities like Tehran. The lack of a good service in this city may result unpleasant consequences on most civilians who live in this city. This paper presents an empirical investigation to measure the performance of six major electricity contractors in city of Tehran, Iran. The study implements grey numbers to handle any unce...

A statistical study of high-altitude electric fields measured on the Viking satellite

International Nuclear Information System (INIS)

Lindqvist, P.A.; Marklund, G.T.

1990-01-01

Characteristics of high-altitude data from the Viking electric field instrument are presented in a statistical study based on 109 Viking orbits. The study is focused in particular on the signatures of and relationships between various parameters measured by the electric field instrument, such as the parallel and transverse (to B) components of the electric field instrument, such as electric field variability. A major goal of the Viking mission was to investigate the occurrence and properties of parallel electric fields and their role in the auroral acceleration process. The results in this paper on the altitude distribution of the electric field variability confirm earlier findings on the distribution of small-scale electric fields and indicate the presence of parallel fields up to about 11,000 km altitude. The directly measured parallel electric field is also investigated in some detail. It is in general directed upward with an average value of 1 mV/m, but depends on, for example, altitude and plasma density. Possible sources of error in the measurement of the parallel field are also considered and accounted for

Recombinant albumin adsorption on mica studied by AFM and streaming potential measurements.

Science.gov (United States)

Kujda, Marta; Adamczyk, Zbigniew; Morga, Maria; Sofińska, Kamila

2015-03-01

Recombinant human serum albumin (rHSA) in monomeric state is widely used in pharmaceutical industry as a drug excipient and for preparing coatings for medical devices. In this work the adsorption process of rHSA on model mica surface at pH 3.5 was studied using the atomic force microscopy (AFM) and in situ streaming potential measurements. The kinetics of albumin adsorption was determined by a direct enumeration of single molecules over various substrate areas. These results were consistent with streaming potential measurements carried out for the parallel-plate channel flow and with theoretical predictions derived from the random sequential adsorption (RSA) model. Desorption kinetics of albumin under flow conditions was also evaluated via the streaming potential measurements. In this way, the amount of irreversibly bound albumin was quantitatively evaluated to be 0.64 and 1.2 mg m(-2) for ionic strength of 0.01 and 0.15 M, respectively. This agrees with previous results obtained for HSA and theoretical calculations derived from the RSA model. Additionally, it was demonstrated that there existed a fraction of reversibly bound albumin that can be fully eluted within a few hours. The binding energy of these fraction of molecules was -18 kT that is consistent with the electrostatic controlled adsorption mechanism of albumin at this pH. It was concluded that the rHSA monolayers of well-defined coverage can find applications for quantitatively analyzing ligand binding and for performing efficient biomaterials and immunological tests. Copyright © 2015 Elsevier B.V. All rights reserved.

La industria cerámica brasileña

Directory of Open Access Journals (Sweden)

Pacheco Jordao, M. A.

2001-02-01

Full Text Available Ceramics play an important role in the Brazilian economy, with a participation estimated in 1% of the GNP ( Gross National Product, corresponding to about 6 billion dollars. The abundance of natural raw-materials, alternative energy sources, and the availability of practical technologies within the industrial equipments, caused a rapid evolution of the Brazilian industries, and several types of products from the various ceramic segments attained international quality levels, with significative exportation. He ceramic sector is very diverse and can be divided into the following classes: heavy clay ceramics, wall and floor tiles, refractory materials, sanitary ware, porcelain electric insulators, tableware, decorative china, ceramic filters and reservoirs for domestic use, technical ceramics, and thermal insulators. All these segments exist in Brazil, in a higher or lower stage of development and production capacity. Moreover, there are also manufacturers of synthetic glazes and colorants, plaster of paris, equipments and some auxiliary chemicals. In this paper, an overview of the main Brazilian ceramic segments is presented, excluding the glass, cement, and lime sectors, which, despite being ceramic, are generally treated in separate.

La cerámica juega un papel muy importante para la economía del país brasileño con una participación en el P.I.B (Producto Interior Bruto estimado en el 1%, correspondiendo a cerca de 6 millones de dólares. La abundancia de materias primas naturales, fuentes alternativas de energía y una amplia tecnología incorporada a los equipos industriales, han hecho que las industrias brasileñas evolucionasen rápidamente de forma que muchos tipos de productos de diferentes segmentos de la actividad cerámica alcanzasen niveles de calidad mundial, con cifras apreciables destinadas a la exportación. El sector industrial de la cerámica incluye producciones muy diversificados y puede ser dividido en los siguientes

electroquímica

Directory of Open Access Journals (Sweden)

HÉCTOR FABIÁN RESTREPO

2005-01-01

Full Text Available En este trabajo se estudió el efecto de la temperatura y la concentración inicial de la anilina sobre la morfología y la conductividad de polianilina obtenida por electropolimerización con voltametría cíclica en soportes de carbón vítreo. La sal de anilina inicial se caracterizó mediante análisis infrarrojo (I.R. La morfología de la polianilina obtenida se analizó por medio de microscopio electrónico (S.E.M., y la conductividad mediante impedancia electroquímica (E.I.S.. Los resultados mostraron un aumento en la velocidad de polimerización y cambios en la morfología del polímero con el aumento de la temperatura y de la concentración del monómero. Los análisis S.E.M. mostraron tres tipos de formaciones poliméricas para los diferentes parámetros de polimerización: lentejuelas, filamentos y gránulos. Los resultados de EIS muestran mayor conductividad y alta capacitancia del polímero a mayores temperaturas y concentraciones.

A combined sustainability index for electricity efficiency measures

International Nuclear Information System (INIS)

Goldrath, T.; Ayalon, O.; Shechter, M.

2015-01-01

One of the most substantial tools that serve decision makers in their efforts to reduce greenhouse gas emissions includes energy efficiency measures that in most cases benefit from governmental assistance for achieving electricity consumption reduction goals. This paper examines five energy efficiency measures, defining a combined sustainability index. A multi-criteria analysis of five predefined indices was developed (economic, environmental, technology, social and political), providing a combined index for each measure and a tool for identifying the preferred measure within a specific situation, based on its total sustainability score. In this research, a case study was conducted and the preferred measure was found to be municipal street lighting systems, based on its high political and social scores, and its relatively high installation potential. The second choice would be replacement of chillers in the industrial sector, and the least favorable measure is the replacement of water pumps in the water sector. The methodology described brings into account the technological specifications of the measure implemented, and the specific national conditions under which it is implemented. - Highlights: • A MCDA of five indices was developed to define a combined sustainability index. • Criteria defined were environment, technology, economy, social and political. • Five energy efficiency measures were rated, based on their total sustainability score. • Measures were in five main electricity consumption sectors. • The preferred measure found in the case study was municipal street lighting systems.

The effect of Er on MSE measurements of q, a new technique for measuring Er, and a test of the neoclassical electric field

International Nuclear Information System (INIS)

Zarnstorff, M.C.; Synakowski, E.J.

1996-10-01

Previous analysis of motional-Stark Effect (MSE) data to measure the q-profile ignored contributions from the plasma electric field. The MSE measurements are shown to be sensitive to the electric field and require significant corrections for plasmas with large rotation velocities or pressure gradients. MSE measurements from rotating plasmas on the Tokamak Fusion Test Reactor (TFTR) confirm the significance of these corrections and verify their magnitude. Several attractive configurations are considered for future MSE-based diagnostics for measuring the plasma radial electric field. MSE data from TFTR is analyzed to determine the change in the radial electric field between two plasmas. The measured electric field quantitatively agrees with the predictions of neoclassical theory. These results confirm the utility of a MSE electric field measurement

Electrical Impedance Measurements of PZT Nanofiber Sensors

Directory of Open Access Journals (Sweden)

Richard Galos

2017-01-01

Full Text Available Electrical impedance measurements of PZT nanofiber sensors were performed using a variety of methods over a frequency spectrum ranging from DC to 1.8 GHz. The nanofibers formed by electrospinning with diameters ranging from 10 to 150 nm were collected and integrated into sensors using microfabrication techniques. Special matching circuits with ultrahigh input impedance were fabricated to produce low noise, measurable sensor outputs. Material properties including resistivity and dielectric constant are derived from the impedance measurements. The resulting material properties are also compared with those of individual nanofibers being tested using conductive AFM and Scanning Conductive Microscopy.

21 CFR 73.1350 - Mica-based pearlescent pigments.

Science.gov (United States)

2010-04-01

... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1350 Mica-based pearlescent pigments. (a) Identity. (1) The color additive is formed by depositing titanium and/or iron salts onto mica, followed by...; titanium dioxide and iron oxide on mica. Mica used to manufacture the color additive shall conform in...

21 CFR 73.350 - Mica-based pearlescent pigments.

Science.gov (United States)

2010-04-01

... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Foods § 73.350 Mica-based pearlescent pigments. (a) Identity. (1) The color additive is formed by depositing titanium salts onto mica, followed by heating to produce titanium dioxide on mica. Mica used to manufacture the color additive shall conform in identity to...

Assembly for electrical conductivity measurements in the piston cylinder device

Science.gov (United States)

Watson, Heather Christine [Dublin, CA; Roberts, Jeffrey James [Livermore, CA

2012-06-05

An assembly apparatus for measurement of electrical conductivity or other properties of a sample in a piston cylinder device wherein pressure and heat are applied to the sample by the piston cylinder device. The assembly apparatus includes a body, a first electrode in the body, the first electrode operatively connected to the sample, a first electrical conductor connected to the first electrode, a washer constructed of a hard conducting material, the washer surrounding the first electrical conductor in the body, a second electrode in the body, the second electrode operatively connected to the sample, and a second electrical conductor connected to the second electrode.

Measurements of Electric Field in a Nanosecond Pulse Discharge by 4-WAVE Mixing

Science.gov (United States)

Baratte, Edmond; Adamovich, Igor V.; Simeni Simeni, Marien; Frederickson, Kraig

2017-06-01

Picosecond four-wave mixing is used to measure temporally and Picosecond four-wave mixing is used to measure temporally and spatially resolved electric field in a nanosecond pulse dielectric discharge sustained in room air and in an atmospheric pressure hydrogen diffusion flame. Measurements of the electric field, and more precisely the reduced electric field (E/N) in the plasma is critical for determination rate coefficients of electron impact processes in the plasma, as well as for quantifying energy partition in the electric discharge among different molecular energy modes. The four-wave mixing measurements are performed using a collinear phase matching geometry, with nitrogen used as the probe species, at temporal resolution of about 2 ns . Absolute calibration is performed by measurement of a known electrostatic electric field. In the present experiments, the discharge is sustained between two stainless steel plate electrodes, each placed in a quartz sleeve, which greatly improves plasma uniformity. Our previous measurements of electric field in a nanosecond pulse dielectric barrier discharge by picosecond 4-wave mixing have been done in air at room temperature, in a discharge sustained between a razor edge high-voltage electrode and a plane grounded electrode (a quartz plate or a layer of distilled water). Electric field measurements in a flame, which is a high-temperature environment, are more challenging because the four-wave mixing signal is proportional to the to square root of the difference betwen the populations of N2 ground vibrational level (v=0) and first excited vibrational level (v=1). At high temperatures, the total number density is reduced, thus reducing absolute vibrational level populations of N2. Also, the signal is reduced further due to a wider distribution of N2 molecules over multiple rotational levels at higher temperatures, while the present four-wave mixing diagnostics is using spectrally narrow output of a ps laser and a high

An optical, electrical and ultrasonic layered single sensor for ingredient measurement in liquid

International Nuclear Information System (INIS)

Kimoto, A; Kitajima, T

2010-01-01

In this paper, an optical, electrical and ultrasonic layered single sensor is proposed as a new, non-invasive sensing method for the measurement of ingredients in liquid, particularly in the food industry. In the proposed sensor, the photo sensors and the PVDF films with the transparent conductive electrode are layered and the optical properties of the liquid are measured by a light emitting diode (LED) and a phototransistor (PT). In addition, the electrical properties are measured by indium tin oxide (ITO) film electrodes as the transparent conductive electrodes of PVDF films arranged on the surfaces of the LED and PT. Moreover, the ultrasonic properties are measured by PVDF films. Thus, the optical, electrical and ultrasonic properties in the same space of the liquid can be simultaneously measured at a single sensor. To test the sensor experimentally, three parameters of the liquid—such as concentrations of yellow color, sodium chloride (NaCl) and ethanol in distilled water—were estimated using the measurement values of the optical, electrical and ultrasonic properties obtained with the proposed sensor. The results suggested that it is possible to estimate the three ingredient concentrations in the same space of the liquid from the optical, electrical and ultrasonic properties measured by the proposed single sensor, although there are still some problems such as measurement accuracy that must be solved

Defect Investigation of Plastically Deformed Al 5454 Wrought Alloy using PADBS and Electrical Measurements

International Nuclear Information System (INIS)

Abdel-Rahman, M.; Kamel, N.A.; Lotfy, Y.A.; Badawi, E.A.; Abdel-Rahman, M.A.

2009-01-01

Positron Annihilation Doppler Broadening Spectroscopy (PADPS) is a nondestructive technique used in material science. Electrical measurements are one of the oldest techniques used also in material science. This paper aimed to discuss the availability of using both PADPS and electrical measurements as diagnostic techniques to detect the defects in a set of plastically deformed 5454 wrought aluminum alloy. The results of the positron annihilation measurements and the electrical measurements were analyzed in terms of the two-state trapping model. This model can be used to investigate both defect and dislocation densities of the samples under investigation. Results obtained by both nuclear and electrical techniques have been reportedity

Absorption measurement s in InSe single crystal under an applied electric field

International Nuclear Information System (INIS)

Ates, A.; Guerbulak, B.; Guer, E.; Yildirim, T.; Yildirim, M.

2002-01-01

InSe single crystal was grown by Bridgman-Stockberger method. Electric field effect on the absorption measurements have been investigated as a function of temperature in InSe single crystal. The absorption edge shifted towards longer wavelengths and decreased of intensity in absorption spectra under an electric field. Using absorption measurements, Urbach energy was calculated under an electric field. Applied electric field caused a increasing in the Urbach energy. At 10 K and 320 K, the first exciton energies were calculated as 1.350 and 1.311 eV for zero voltage and 1.334 and 1.301 eV for electric field respectively

Electric fields in accelerating conductors: measurement of the EMF in rotationally accelerating coils

Energy Technology Data Exchange (ETDEWEB)

Moorhead, G.F.; Opat, G.I.

1996-06-06

The acceleration of an electric conductor is predicted to produce an electric filed proportional to m/q where `m`is the free mass and `q` the charge of the carriers of the electric current. In certain configurations this leads to a measurable electromagnetic field (EMF). In this paper is reported a measurement of the EMF induced by rotationally accelerating coils of aluminium and copper wire. The measured EMFs are found to agree with the theoretical predictions to within the error estimates. 23 refs., 1 tab., 4 figs.

Electric fields in accelerating conductors: measurement of the EMF in rotationally accelerating coils

International Nuclear Information System (INIS)

Moorhead, G.F.; Opat, G.I.

1996-01-01

The acceleration of an electric conductor is predicted to produce an electric filed proportional to m/q where 'm'is the free mass and 'q' the charge of the carriers of the electric current. In certain configurations this leads to a measurable electromagnetic field (EMF). In this paper is reported a measurement of the EMF induced by rotationally accelerating coils of aluminium and copper wire. The measured EMFs are found to agree with the theoretical predictions to within the error estimates. 23 refs., 1 tab., 4 figs

Comparison of electric field exposure measurement methods under power lines

International Nuclear Information System (INIS)

Korpinen, L.; Kuisti, H.; Tarao, H.; Paeaekkoenen, R.; Elovaara, J.

2014-01-01

The object of the study was to investigate extremely low frequency (ELF) electric field exposure measurement methods under power lines. The authors compared two different methods under power lines: in Method A, the sensor was placed on a tripod; and Method B required the measurer to hold the meter horizontally so that the distance from him/her was at least 1.5 m. The study includes 20 measurements in three places under 400 kV power lines. The authors used two commercial three-axis meters, EFA-3 and EFA-300. In statistical analyses, they did not find significant differences between Methods A and B. However, in the future, it is important to take into account that measurement methods can, in some cases, influence ELF electric field measurement results, and it is important to report the methods used so that it is possible to repeat the measurements. (authors)

Method for Measuring Small Nonlinearities of Electric Characteristics

DEFF Research Database (Denmark)

Guldbrandsen, Tom; Meyer, Niels I; Schjær-Jacobsen, Jørgen

1965-01-01

A method is described for measuring very small deviations from linearity in electric characteristics. The measurement is based on the harmonics generated by the nonlinear element when subjected to a sine wave signal. A special bridge circuit is used to balance out the undesired harmonics...... of the signal generator together with the first harmonic frequency. The set-up measures the small-signal value and the first and second derivative with respect to voltage. The detailed circuits are given for measuring nonlinearities in Ohmic and capacitive components. In the Ohmic case, a sensitivity...

MICA: The Meta-Institute for Computational Astrophysics

Science.gov (United States)

McMillan, Stephen L. W.; Djorgovski, S. G.; Hut, P.; Vesperini, E.; Knop, R.; Portegies Zwart, S.

2009-05-01

We describe MICA, the Meta Institute for Computational Astrophysics, the first professional scientific and educational, non-profit organization based in virtual worlds [VWs]. Most MICA activities are currently conducted in Second Life, arguably the most popular and best developed VW; we plan to expand our presence into other VWs as those venues evolve. The goals of MICA include (1) exploration, development and promotion of VWs and virtual reality [VR] technologies for professional research in astronomy and related fields; (2) development of novel networking venues and mechanisms for virtual scientific communication and interaction, including professional meetings, visualization, and telecollaboration; (3) use of VWs and VR technologies for education and public outreach; and (4) exchange of ideas and joint efforts with other scientific disciplines in promoting these goals for science and scholarship in general. We present representative example of MICA activities and achievements, and outline plans for expansion of the organization. For more information on MICA, please visit http://mica-vw.org .

Apparatus for simultaneously measuring electrical conductivity and oxygen fugacity

Energy Technology Data Exchange (ETDEWEB)

Netherton, R.; Duba, A.

1978-01-31

Electrical conductivity studies of silicates are useful in determining temperature vs depth in the earth. Realistic laboratory measurements of conduction mechanisms require that exact determinations of oxygen fugacity (fo{sub 2}) be made in the experimental environment. An apparatus is described that monitors system fo{sub 2} with a calcia-doped zirconia-oxygen cell while measuring electrical conductivity of iron-bearing silicates at high temperature (greater than 1000 K). The fo{sub 2} calculated thermodynamically from CO/CO{sub 2} mixing ratios agreed well with measurements made with the zirconia cell at 1473 K, except for fo{sub 2} greater than 10{sup -4} Pa, where, on a log{sub 10} scale, mixing-ratio errors were as large as +- 0.2. These errors are attributed to oxygen contamination in the CO{sub 2} and to mobile carbon deposits that formed in the apparatus.

Acute Antibody-Mediated Rejection in Presence of MICA-DSA and Successful Renal Re-Transplant with Negative-MICA Virtual Crossmatch.

Directory of Open Access Journals (Sweden)

Yingzi Ming

Full Text Available The presence of donor-specific alloantibodies (DSAs against the MICA antigen results in high risk for antibody-mediated rejection (AMR of a transplanted kidney, especially in patients receiving a re-transplant. We describe the incidence of acute C4d+ AMR in a patient who had received a first kidney transplant with a zero HLA antigen mismatch. Retrospective analysis of post-transplant T and B cell crossmatches were negative, but a high level of MICA alloantibody was detected in sera collected both before and after transplant. The DSA against the first allograft mismatched MICA*018 was in the recipient. Flow cytometry and cytotoxicity tests with five samples of freshly isolated human umbilical vein endothelial cells demonstrated the alloantibody nature of patient's MICA-DSA. Prior to the second transplant, a MICA virtual crossmatch and T and B cell crossmatches were used to identify a suitable donor. The patient received a second kidney transplant, and allograft was functioning well at one-year follow-up. Our study indicates that MICA virtual crossmatch is important in selection of a kidney donor if the recipient has been sensitized with MICA antigens.

Aula virtual como estrategia para el aprendizaje de la Química Orgánica

Directory of Open Access Journals (Sweden)

Alexander Castillo

2017-01-01

Full Text Available El propósito fue describir la experiencia de aplicar el aula virtual como estrategia para el aprendizaje de la Química Orgánica. Teóricamente se basa en Scagnoli (2000, fundamentada en la metodología cualitativa, tipo sistematización de experiencias; los actores fueron 43 estudiantes de la asignatura Química Orgánica I de la Facultad de Humanidades y Educación de la Universidad del Zulia. Se utilizó la observación, sesiones en profundidad y la lista de cotejo. Los estudiantes demostraron interés en las TIC para comprender los contenidos de la asignatura. Se concluye que el aula virtual favorece el autoaprendizaje electrónico, incentiva el aprendizaje y la gestión del conocimiento.

Effects of heat and electricity saving measures in district-heated multistory residential buildings

International Nuclear Information System (INIS)

Truong, Nguyen Le; Dodoo, Ambrose; Gustavsson, Leif

2014-01-01

Highlights: • We analyzed the potential for energy savings in district heated buildings. • Measures that reduce more peak load production give higher primary energy savings. • Efficient appliances increase heat demand but give net primary energy savings. • Efficient appliances give the largest net primary energy savings. - Abstract: The effects of heat and electricity saving measures in district-heated buildings can be complex because these depend not only on how energy is used on the demand side but also on how energy is provided from the supply side. In this study, we analyze the effects of heat and electricity saving measures in multistory concrete-framed and wood-framed versions of an existing district-heated building and examine the impacts of the reduced energy demand on different district heat (DH) production configurations. The energy saving measures considered are for domestic hot water reduction, building thermal envelope improvement, ventilation heat recovery (VHR), and household electricity savings. Our analysis is based on a measured heat load profile of an existing DH production system in Växjö, Sweden. Based on the measured heat load profile, we model three minimum-cost DH production system using plausible environmental and socio-political scenarios. Then, we investigate the primary energy implications of the energy saving measures applied to the two versions of the existing building, taking into account the changed DH demand, changed cogenerated electricity, and changed electricity use due to heat and electricity saving measures. Our results show that the difference between the final and primary energy savings of the concrete-framed and wood-framed versions of the case-study building is minor. The primary energy efficiency of the energy saving measures depends on the type of measure and on the composition of the DH production system. Of the various energy saving measures explored, electricity savings give the highest primary energy savings

RESISTIVIDAD INDUCIDA PRO SCATTERING ELECTRON-SUPERFICIE RUGOSA Y SCATTERING ELECTRON BORDE DE GRANO EN PELICULAS DELGADAS DE ORO DEPOSITADAS SOBRE MICA

OpenAIRE

HENRIQUEZ CORREA, RICARDO ANDRES; HENRIQUEZ CORREA, RICARDO ANDRES

2010-01-01

En este trabajo se presenta un método experimental que permite separar el efecto de las colisiones electrón-borde de grano y electrón-superficie sobre la resistividad eléctrica en películas delgadas de oro evaporadas sobre mica. Cuando el efecto de las colisiones electrón-borde de grano es dominante, la resistividad no depende del espesor de la muestra, el camino libre medio a 4 K es el diámetro medio de grano, la dependencia de la resistividad con temperatura puede ser descrita mediant...

RESISTIVIDAD INDUCIDA POR SCATTERING ELECTRON-SUPERFICIE RUGOSA Y SCATTERING ELECTRON BORDE DE GRANO EN PELICULAS DELGADAS DE ORO DEPOSITADAS SOBRE MICA

OpenAIRE

HENRIQUEZ CORREA; RICARDO ANDRES; HENRIQUEZ CORREA; RICARDO ANDRES

2010-01-01

En este trabajo se presenta un método experimental que permite separar el efecto de las colisiones electrón-borde de grano y electrón-superficie sobre la resistividad eléctrica en películas delgadas de oro evaporadas sobre mica. Cuando el efecto de las colisiones electrón-borde de grano es dominante, la resistividad no depende del espesor de la muestra, el camino libre medio a 4 K es el diámetro medio de grano, la dependencia de la resistividad con temperatura puede ser descrit...

Measuring user similarity using electric circuit analysis: application to collaborative filtering.

Science.gov (United States)

Yang, Joonhyuk; Kim, Jinwook; Kim, Wonjoon; Kim, Young Hwan

2012-01-01

We propose a new technique of measuring user similarity in collaborative filtering using electric circuit analysis. Electric circuit analysis is used to measure the potential differences between nodes on an electric circuit. In this paper, by applying this method to transaction networks comprising users and items, i.e., user-item matrix, and by using the full information about the relationship structure of users in the perspective of item adoption, we overcome the limitations of one-to-one similarity calculation approach, such as the Pearson correlation, Tanimoto coefficient, and Hamming distance, in collaborative filtering. We found that electric circuit analysis can be successfully incorporated into recommender systems and has the potential to significantly enhance predictability, especially when combined with user-based collaborative filtering. We also propose four types of hybrid algorithms that combine the Pearson correlation method and electric circuit analysis. One of the algorithms exceeds the performance of the traditional collaborative filtering by 37.5% at most. This work opens new opportunities for interdisciplinary research between physics and computer science and the development of new recommendation systems.

Measuring user similarity using electric circuit analysis: application to collaborative filtering.

Directory of Open Access Journals (Sweden)

Joonhyuk Yang

Full Text Available We propose a new technique of measuring user similarity in collaborative filtering using electric circuit analysis. Electric circuit analysis is used to measure the potential differences between nodes on an electric circuit. In this paper, by applying this method to transaction networks comprising users and items, i.e., user-item matrix, and by using the full information about the relationship structure of users in the perspective of item adoption, we overcome the limitations of one-to-one similarity calculation approach, such as the Pearson correlation, Tanimoto coefficient, and Hamming distance, in collaborative filtering. We found that electric circuit analysis can be successfully incorporated into recommender systems and has the potential to significantly enhance predictability, especially when combined with user-based collaborative filtering. We also propose four types of hybrid algorithms that combine the Pearson correlation method and electric circuit analysis. One of the algorithms exceeds the performance of the traditional collaborative filtering by 37.5% at most. This work opens new opportunities for interdisciplinary research between physics and computer science and the development of new recommendation systems.

Analysis of electric vehicles measurements

NARCIS (Netherlands)

Vonk, B.M.J.; Geldtmeijer, D.A.M.; Slootweg, J.G.

2013-01-01

Electric vehicles are expected to have a significant impact on electricity grids. Intelligent charging strategies are suggested by literature and tested in the field to prevent overloading of network assets in electricity grids by using the flexibility of electro-mobility. This paper covers an

Electrical resistivity measurements in superconducting ceramics

International Nuclear Information System (INIS)

Muccillo, R.; Bressiani, A.H.A.; Muccillo, E.N.S.; Bressiani, J.C.

1988-01-01

Electrical resistivity measurements have been done in (Y, Ba, Cu, O) - and (Y, A1, Ba, Cu, O) - based superconducting ceramics. The sintered specimens were prepared by applying gold electrodes and winding on the non-metalized part with a copper strip to be immersed in liquid nitrogen for cooling. The resistivity measurements have been done by the four-probe method. A copper-constantan or chromel-alumel thermocouple inserted between the specimen and the copper cold finger has been used for the determination of the critical temperature T c . Details of the experimental set-up and resistivity versus temperature plots in the LNT-RT range for the superconducting ceramics are the major contributions of this communication. (author) [pt

Electrical resistivity measurements in superconducting ceramics

International Nuclear Information System (INIS)

Muccillo, R.; Bressiani, A.H.A.; Muccillo, E.N.S.; Bressian, J.C.

1988-01-01

Electrical resistivity measurements have been done in (Y,Ba,Cu,O)- and (Y,Al,Ba,Cu,O)-based superconducting ceramics. The sintered specimens were prepared by applying gold electrodes and winding on the non-metalized part with a copper strip to be immersed in liquid nitrogen for cooling. The resistivity measurements have been done by the four-probe method. A copper constantan or chromel-alumel thermocouple inserted between the specimen and the copper cold finger has been used for the determination of the critical temperature T c . Details of the experimental set-up and resistivity versus temperature plots in the LNT-RT range for the superconducting ceramics are the major contributions of this communication. (author) [pt

Electric field measurements in a NLC/PMSE region during the MASS/ECOMA campaign

Directory of Open Access Journals (Sweden)

M. Shimogawa

2009-04-01

Full Text Available We present results of electric field measurements made during the MASS rocket campaign in Andøya, Norway into noctilucent clouds (NLC and polar mesospheric summer echoes (PMSE on 3 August 2007. The instrument used high input-impedance preamps to measure vertical and horizontal electric fields. No large-amplitude geophysical electric fields were detected in the cloud layers, but significant levels of electric field fluctuations were measured. Within the cloud layer, the probe potentials relative to the rocket skin were driven negative by incident heavy charged aerosols. The amplitude of spikes caused by probe shadowing were also larger in the NLC/PMSE region. We describe a method for calculating positive ion conductivities using these shadowing spike amplitudes and the density of heavy charged aerosols.

Modernization of laboratories of test of electric measurer

International Nuclear Information System (INIS)

Cuervo, Luis Felipe

1999-01-01

The paper presents to the companies that possess test laboratories and calibration of electric measurer, an economic alternative for their modernization, using the repontentiation like an economic solution that it liberates resources to be used in other areas that they want it

Design of a fiber optical sensor for atmospheric electric field measurement

International Nuclear Information System (INIS)

Baghdasaryan, H.V.; Knyazyan, T.M.; Daryan, A.V.

2016-01-01

All-optical sensor for atmospheric electric field detection and measurement is suggested and numerically modelled. Thin electro- optical crystal sandwiched between two distributed Bragg reflectors (DBRs) forming multilayer Gires-Tournois (G-T) microresonator is used as a sensitive part of the electric field sensor. In the sensor device, an optical fiber delivers the wideband light spectrum to the sensing multilayer structure of G-T microresonator. The reflectance spectrum of the sensor contains information on the electric field strength and direction. The relevant reflectance peaks’ shift in the reflected spectrum can be observed by an optical spectrum analyzer (OSA). Numerical modelling has been done by the method of single expression that is a suitable tool for multi-boundary problems solution. The obtained results of modelling will be useful in a new type of non-distorting sensor’s elaboration for atmospheric electric field detection and measurement. (author)

Ionic double layer of atomically flat gold formed on mica templates

International Nuclear Information System (INIS)

Chilcott, Terry C.; Wong, Elicia L.S.; Coster, Hans G.L.; Coster, Adelle C.F.; James, Michael

2009-01-01

Electrical impedance spectroscopy characterisations of gold surfaces formed on mica templates in contact with potassium chloride electrolytes were performed at the electric potential of zero charge over a frequency range of 6 x 10 -3 to 100 x 10 3 Hz. They revealed constant-phase-angle (CPA) behaviour with a frequency exponent value of 0.96 for surfaces that were also characterised as atomically flat using atomic force microscopy (AFM). As the frequency exponent value was only marginally less than unity, the CPA behaviour yielded a realistic estimate for the capacitance of the ionic double layer. The retention of the CPA behaviour was attributed to specific adsorption of chloride ions which was detected as an adsorption conductance element in parallel with the CPA impedance element. Significant variations in the ionic double layer capacitance as well as the adsorption conductance were observed for electrolyte concentrations ranging from 33 μM to 100 mM, but neither of these variations correlated with concentration. This is consistent with the electrical properties of the interface deriving principally from the inner or Stern region of the double layer.

Diffusivity and electrical resistivity measurements in rock matrix around fractures

International Nuclear Information System (INIS)

Kumpulainen, H.; Uusheimo, K.

1989-12-01

Microfracturing of rock matrix around permeable fractures was studied experimentally from drill core samples around major fractures. The methods used were diffusion measurements using a 36 Cl-tracer and electrical resistivity measurements. Rock samples were from the Romuvaara investigation site, the granite specimen around a partially filled carbonate fracture (KR4/333 m) and gneiss specimen around a slickenside fracture (KR1/645 m). A consistent difference of one to two orders of magnitude in the levels of the methods with regard to the effective diffusion coefficients for Cl - -ion was found, the electrical resistivity measurement giving higher values. On the basis of the diffusion measurements the diffusion porosities could be calculated but these remained one to two orders of magnitude lower than that expected for granitic rocks using the water saturation method. A possible reason for these differences could have been the low, in some cases 0.004 M NaC1-concentration in the diffusion experiments vs. the 1 M NaCl-concentration used in the electrical resistivity measurements. Due to the small number of specimens and cross sectional areas of only 2 cm 2 , rock inhomogeneity effects were significant making the interpretation of the results somewhat troublesome. Porosities on fracture surfaces seemed to be higher than in the deeper, more intact rock matrix

Two-mica granites of northeastern Nevada.

Science.gov (United States)

Lee, D.E.; Kistler, R.W.; Friedman, I.; Van Loenen, R. E.

1981-01-01

The field settings are described and analytical data are presented for six two-mica granites from NE Nevada. High delta 18O and 87Sr/86Sr values indicate that all are S-type granite, derived from continental crust. The major element chemistry and accessory mineral contents of these rocks also are characteristic of S-type granites. Chemical, X ray, and other data are presented for the micas recovered from these granites. The muscovites are notably high in Fe2O3, FeO, and MgO. Except for one hydrobiotite, each of the biotites has an MgO content near 6.0 wt%. Two different types of two-mica granites are recognized in the area of this study. One type is distinguished by the presence of many biotite euhedra within muscovite phenocrysts and by an unusual suite of accessory minerals completely devoid of opaque oxides. This type probably resulted from anatexis of late Precambrian argillites under conditions of relatively low oxygen fugacity, along a line that roughly coincides with the westward disappearance of continental basement. In the other textural type of two-mica granite the micas are equigranular and there is a greater variety of accessory minerals. The magmatic evolution of this type also appears to reflect the influence of late Precambrian argillites; there may be age differences between the two types of two-mica granites.-Author

Electric field vector measurements in a surface ionization wave discharge

International Nuclear Information System (INIS)

Goldberg, Benjamin M; Adamovich, Igor V; Lempert, Walter R; Böhm, Patrick S; Czarnetzki, Uwe

2015-01-01

This work presents the results of time-resolved electric field vector measurements in a short pulse duration (60 ns full width at half maximum), surface ionization wave discharge in hydrogen using a picosecond four-wave mixing technique. Electric field vector components are measured separately, using pump and Stokes beams linearly polarized in the horizontal and vertical planes, and a polarizer placed in front of the infrared detector. The time-resolved electric field vector is measured at three different locations across the discharge gap, and for three different heights above the alumina ceramic dielectric surface, ∼100, 600, and 1100 μm (total of nine different locations). The results show that after breakdown, the discharge develops as an ionization wave propagating along the dielectric surface at an average speed of 1 mm ns −1 . The surface ionization wave forms near the high voltage electrode, close to the dielectric surface (∼100 μm). The wave front is characterized by significant overshoot of both vertical and horizontal electric field vector components. Behind the wave front, the vertical field component is rapidly reduced. As the wave propagates along the dielectric surface, it also extends further away from the dielectric surface, up to ∼1 mm near the grounded electrode. The horizontal field component behind the wave front remains quite significant, to sustain the electron current toward the high voltage electrode. After the wave reaches the grounded electrode, the horizontal field component experiences a secondary rise in the quasi-dc discharge, where it sustains the current along the near-surface plasma sheet. The measurement results indicate presence of a cathode layer formed near the grounded electrode with significant cathode voltage fall, ≈3 kV, due to high current density in the discharge. The peak reduced electric field in the surface ionization wave is 85–95 Td, consistent with dc breakdown field estimated from the Paschen

A cable-free impedance and gain measurement technique for electrically small antennas

DEFF Research Database (Denmark)

Pivnenko, Sergey; Zhang, Jiaying; Breinbjerg, Olav

2010-01-01

are represented in terms of spherical wave expansions (SWEs), and the propagation is accounted for by a transmission formula. In this paper the measurement results by the proposed technique will be presented for several AUTs, including a standard gain horn antenna, a monopole antenna, and an electrically small......Impedance and gain measurements for electrically small antennas represent a great challenge due to influences of the feeding cable. The leaking current along the cable and scattering effects are two main issues caused by the feed line. In this paper, a novel cable-free antenna impedance and gain...... measurement technique for electrically small antennas is proposed. The antenna properties are extracted by measuring the signal scattered by the antenna under test (AUT), when it is loaded with three known loads. The technique is based on a rigorous electromagnetic model where the probe and AUT...

Evolución hacia la cerámica fotovoltaica

Directory of Open Access Journals (Sweden)

Sánchez-Muñoz, L.

2011-02-01

Full Text Available Nowadays there are two types of ceramic materials, i.e. traditional and advanced. The origin and development of the first one occurred before the revolutionary changes in Science and Technology of the nineteenth century, while the second one is its direct consequence. The traditional ceramics, which are related primarily to elementary human needs, in particular its constructions, is very homogeneous with respect to their formulations, being their diversity mainly linked to the decorative aspects of one surface. Advanced ceramics are characterized by a wide variety of materials with specific physical and chemical responses to radiation and electromagnetic fields, where major economic benefits are mainly related to secondary human needs such as telecommunications. As a result of the current global crisis, traditional buildings could be rehabilitated and/or replaced by energy efficient buildings, also called zero-energy buildings. In them there is a balance between energy consumed and produced “in situ”, and also using environmentally friendly materials. The direct consequence of this trend will be the evolution of ceramics by partial hybridization of its two ancestors, with special importance of semiconductor compounds, to the production of electrical energy as the basic objective, in this work called photovoltaic ceramics.

Actualmente se distinguen dos tipos de cerámica, una tradicional y otra avanzada. El origen y desarrollo de la primera es anterior a los cambios revolucionarios en Ciencia y Tecnológica del siglo XIX, mientras que la segunda es su consecuencia directa. La cerámica tradicional, que está relacionada sobre todo con las necesidades humanas primarias y en particular a sus construcciones, es muy homogénea respecto a sus formulaciones, estando su diversidad ligada principalmente a los aspectos decorativos de una de sus superficies. La cerámica avanzada se caracteriza por una gran diversidad de materiales con

Fabrication and electric measurements of nanostructures inside transmission electron microscope

International Nuclear Information System (INIS)

Chen, Qing; Peng, Lian-Mao

2011-01-01

Using manipulation holders specially designed for transmission electron microscope (TEM), nanostructures can be characterized, measured, modified and even fabricated in-situ. In-situ TEM techniques not only enable real-time study of structure-property relationships of materials at atomic scale, but also provide the ability to control and manipulate materials and structures at nanoscale. This review highlights in-situ electric measurements and in-situ fabrication and structure modification using manipulation holder inside TEM. -- Research highlights: → We review in-situ works using manipulation holder in TEM. → In-situ electric measurements, fabrication and structure modification are focused. → We discuss important issues that should be considered for reliable results. → In-situ TEM is becoming a very powerful tool for many research fields.

Electrical resistivity borehole measurements: application to an urban tunnel site

Science.gov (United States)

Denis, A.; Marache, A.; Obellianne, T.; Breysse, D.

2002-06-01

This paper shows how it is possible to use wells drilled during geotechnical pre-investigation of a tunneling site to obtain a 2-D image of the resistivity close to a tunnel boring machine. An experimental apparatus is presented which makes it possible to perform single and borehole-to-borehole electrical measurements independent of the geological and hydrogeological context, which can be activated at any moment during the building of the tunnel. This apparatus is first demonstrated through its use on a test site. Numerical simulations and data inversion are used to analyse the experimental results. Finally, electrical resistivity tomography and single-borehole measurements on a tunneling site are presented. Experimental results show the viability of the apparatus and the efficiency of the inverse algorithm, and also highlight the limitations of the electrical resistivity tomography as a tool for geotechnical investigation in urban areas.

Measurement of absolute displacement-amplitude of ultrasonic wave using piezo-electric detection method

Energy Technology Data Exchange (ETDEWEB)

Park, Seong Hyun; Kim, Jong Beom; Jhang, Kyung Young [Hanyang University, Seoul (Korea, Republic of)

2017-02-15

A nonlinear ultrasonic parameter is defined by the ratio of displacement amplitude of the fundamental frequency component to that of the second-order harmonic frequency component. In this study, the ultrasonic displacement amplitude of an SUS316 specimen was measured via a piezo-electric-based method to identify the validity of piezo-electric detection method. For comparison, the ultrasonic displacement was also determined via a laser-based Fabry-Pérot interferometer. The experimental results for both measurements were in good agreement. Additionally, the stability of the repeated test results from the piezo-electric method exceeded that of the laser-interferometric method. This result indicated that the piezo-electric detection method can be utilized to measure a nonlinear ultrasonic parameter due to its excellent stability although it involves a complicated process.

Measurement of absolute displacement-amplitude of ultrasonic wave using piezo-electric detection method

International Nuclear Information System (INIS)

Park, Seong Hyun; Kim, Jong Beom; Jhang, Kyung Young

2017-01-01

A nonlinear ultrasonic parameter is defined by the ratio of displacement amplitude of the fundamental frequency component to that of the second-order harmonic frequency component. In this study, the ultrasonic displacement amplitude of an SUS316 specimen was measured via a piezo-electric-based method to identify the validity of piezo-electric detection method. For comparison, the ultrasonic displacement was also determined via a laser-based Fabry-Pérot interferometer. The experimental results for both measurements were in good agreement. Additionally, the stability of the repeated test results from the piezo-electric method exceeded that of the laser-interferometric method. This result indicated that the piezo-electric detection method can be utilized to measure a nonlinear ultrasonic parameter due to its excellent stability although it involves a complicated process

A quadruple-scanning-probe force microscope for electrical property measurements of microscopic materials

International Nuclear Information System (INIS)

Higuchi, Seiji; Kubo, Osamu; Kuramochi, Hiromi; Aono, Masakazu; Nakayama, Tomonobu

2011-01-01

Four-terminal electrical measurement is realized on a microscopic structure in air, without a lithographic process, using a home-built quadruple-scanning-probe force microscope (QSPFM). The QSPFM has four probes whose positions are individually controlled by obtaining images of a sample in the manner of atomic force microscopy (AFM), and uses the probes as contacting electrodes for electrical measurements. A specially arranged tuning fork probe (TFP) is used as a self-detection force sensor to operate each probe in a frequency modulation AFM mode, resulting in simultaneous imaging of the same microscopic feature on an insulator using the four TFPs. Four-terminal electrical measurement is then demonstrated in air by placing each probe electrode in contact with a graphene flake exfoliated on a silicon dioxide film, and the sheet resistance of the flake is measured by the van der Pauw method. The present work shows that the QSPFM has the potential to measure the intrinsic electrical properties of a wide range of microscopic materials in situ without electrode fabrication.

D.C. electrical conductivity measurements on ADP single crystals ...

Indian Academy of Sciences (India)

Unknown

Impurity added ADP crystals; density; electrical conductivity measurements. 1. Introduction ... determined by the intrinsic defects caused by thermal fluctuations in the ... beaker (corning glass vessel) and allowed to equilibrate at the desired ...

La coyuntura económica nacional

Directory of Open Access Journals (Sweden)

Arturo Huerta González

2003-01-01

Full Text Available El objetivo de este artículo es analizar los problemas de contracción económica que enfrenta nuestro país como resultado de la política económica predominante, que lo ha llevado a depender de la economía estadounidense. Cuando ésta enfrentó problemas de crecimiento también frenó el crecimiento de la economía nacional. El gobierno mexicano no instrumenta política fiscal anticíclica (expansión del gasto para contrarrestar la caída de exportaciones y recuperar la dinámica económica por considerar que ello originaría presiones sobre precios y el sector externo y pudiera llevar a un contexto de especulación y crisis. Es por esto que se opta por seguir priorizando políticas contraccionistas para evitar la inflación, como si éste fuese el principal problema del país. Asimismo, el gobierno insiste en las reformas estructurales (apertura eléctrica, petrolera, reforma fiscal y laboral para ampliar la esfera de influencia del sector privado nacional y extranjero y para consolidar el saneamiento fiscal y abaratar el costo de la fuerza de trabajo, impulsando así la dinámica económica. Sin embargo, tales reformas ya las hemos vivido —desde el gobierno de Salinas de Gortari a la fecha— y sus resultados han sido crecimientos espurios que han desembocado en crisis y en el actual estancamiento. Mientras prosiga la actual política económica seguirá deteriorándose la esfera productiva y aumentando el desempleo, sin que se logre un crecimiento sostenido y menos vulnerable de la economía

QUÍMICA VERDE: UN NUEVO RETO

Directory of Open Access Journals (Sweden)

Nerlis Paola Pájaro Castro

2011-01-01

Full Text Available En la actualidad, existe un enorme deterioro del medio ambiente que ha generado la necesidad de buscar alternativas que conduzcan a la sostenibilidad ambiental. Una de estas herramientas es la ¿química verde¿, concepto que contempla el diseño de productos y procesos que reduzcan la generación de sustancias peligrosas y maximicen la eficiencia en la utilización de recursos materiales y energéticos. El empleo de tecnologías menos contaminantes, permitirá a las empresas químicas mitigar los efectos ambientales asociados a su actividad, reduciendo el consumo de materiales e incrementando la participación de recursos renovables. Para alcanzar estas metas, se han propuesto 12 principios básicos de química verde, aplicables en diferentes campos, tales como la medicina, la agricultura, la industria química y farmacéutica. Esta revisión detalla los principios y usos principales de la química verde, y su aplicación como una filosofía de trabajo para avanzar hacia un verdadero desarrollo sostenible.

Performance measurement of electricity suppliers using PROMETHEE and balance scorecard

Directory of Open Access Journals (Sweden)

Mona Osati

2016-06-01

Full Text Available Performance measurement in energy industry plays an important role on increasing the productivity. Electricity is also among the most essential components of energy in mega cities like Tehran. The lack of a good service in this city may result unpleasant consequences on most civilians who live in this city. This paper presents an empirical investigation to measure the performance of six major electricity contractors in city of Tehran, Iran. The study implements grey numbers to handle any uncertainty associated with numbers. The study has also adopted four main perspectives used in balanced scorecard as part of PROMETHEE method to rank different contractors.

Cutting force measurement of electrical jigsaw by strain gauges

International Nuclear Information System (INIS)

Kazup, L; Varadine Szarka, A

2016-01-01

This paper describes a measuring method based on strain gauges for accurate specification of electric jigsaw's cutting force. The goal of the measurement is to provide an overall perspective about generated forces in a jigsaw's gearbox during a cutting period. The lifetime of the tool is affected by these forces primarily. This analysis is part of the research and development project aiming to develop a special linear magnetic brake for realizing automatic lifetime tests of electric jigsaws or similar handheld tools. The accurate specification of cutting force facilitates to define realistic test cycles during the automatic lifetime test. The accuracy and precision resulted by the well described cutting force characteristic and the possibility of automation provide new dimension for lifetime testing of the handheld tools with alternating movement. (paper)

Paragenesis of Cr-rich muscovite and chlorite in green-mica ...

Indian Academy of Sciences (India)

peculiar green colour is attributed to the concen- tration of .... mica quartzite, 1g: white mica (paucity of green mica) with ..... lacking in the white micas. 6.2 Chlorites. Chlorites are associated with green micas in the. Palasgaon–Saigaon area. EPMA analysis of the representative chlorites has been obtained. Cations.

Mg-doping experiment and electrical transport measurement of boron nanobelts

International Nuclear Information System (INIS)

Kirihara, K.; Hyodo, H.; Fujihisa, H.; Wang, Z.; Kawaguchi, K.; Shimizu, Y.; Sasaki, T.; Koshizaki, N.; Soga, K.; Kimura, K.

2006-01-01

We measured electrical conductance of single crystalline boron nanobelts having α-tetragonal crystalline structure. The doping experiment of Mg was carried out by vapor diffusion method. The pure boron nanobelt is a p-type semiconductor and its electrical conductivity was estimated to be on the order of 10 -3 (Ω cm) -1 at room temperature. The carrier mobility of pure boron nanobelt was measured to be on the order of 10 -3 (cm 2 Vs -1 ) at room temperature and has an activation energy of ∼0.19 eV. The Mg-doped boron nanobelts have the same α-tetragonal crystalline structure as the pristine nanobelts. After Mg vapor diffusion, the nanobelts were still semiconductor, while the electrical conductance increased by a factor of 100-500. Transition to metal or superconductor by doping was not observed. - Graphical abstract: SEM micrographs of boron nanobelt after Ni/Au electrode fabrication by electron beam lithography. Display Omitted

Measurement of Anisotropic Particle Interactions with Nonuniform ac Electric Fields.

Science.gov (United States)

Rupp, Bradley; Torres-Díaz, Isaac; Hua, Xiaoqing; Bevan, Michael A

2018-02-20

Optical microscopy measurements are reported for single anisotropic polymer particles interacting with nonuniform ac electric fields. The present study is limited to conditions where gravity confines particles with their long axis parallel to the substrate such that particles can be treated using quasi-2D analysis. Field parameters are investigated that result in particles residing at either electric field maxima or minima and with long axes oriented either parallel or perpendicular to the electric field direction. By nonintrusively observing thermally sampled positions and orientations at different field frequencies and amplitudes, a Boltzmann inversion of the time-averaged probability of states yields kT-scale energy landscapes (including dipole-field, particle-substrate, and gravitational potentials). The measured energy landscapes show agreement with theoretical potentials using particle conductivity as the sole adjustable material property. Understanding anisotropic particle-field energy landscapes vs field parameters enables quantitative control of local forces and torques on single anisotropic particles to manipulate their position and orientation within nonuniform fields.

Algoritmos para genómica comparativa

OpenAIRE

Figueiras, Vasco da Rocha

2010-01-01

Com o surgimento da Genómica e da Proteómica, a Bioinformática conduziu a alguns dos avanços científicos mais relevantes do século XX. A Unidade de Investigação e Desenvolvimento do Biocant, parque biotecnológico de Cantanhede, assume actualmente o papel de motor no desenvolvimento da Genómica. O Biocant possui um importante sequenciador de larga escala que permite armazenar um elevado número de genomas, nomeadamente, genomas de bactérias. O estudo proposto reflecte a necessidade do Bio...

Determining of the electric field strength using high frequency broadband measurements

Directory of Open Access Journals (Sweden)

Vulević Branislav D.

2017-01-01

Full Text Available Exposure of humans to electromagnetic fields of high frequency (above 100 kHz, i.e. radiofrequency radiation from the modern wireless systems, today inevitable is. The purpose of this paper is to highlight the importance of broadband measurements of the electric field of high frequency in order to fast and reliable assessment of human exposure. A practical method of ‘in situ’ measurement the electric field intensity which is related to the frequency range of 3 MHz to 18 GHz, is provided.

Matrix diffusion studies by electrical conductivity methods. Comparison between laboratory and in-situ measurements

International Nuclear Information System (INIS)

Ohlsson, Y.; Neretnieks, I.

1998-01-01

Traditional laboratory diffusion experiments in rock material are time consuming, and quite small samples are generally used. Electrical conductivity measurements, on the other hand, provide a fast means for examining transport properties in rock and allow measurements on larger samples as well. Laboratory measurements using electrical conductivity give results that compare well to those from traditional diffusion experiments. The measurement of the electrical resistivity in the rock surrounding a borehole is a standard method for the detection of water conducting fractures. If these data could be correlated to matrix diffusion properties, in-situ diffusion data from large areas could be obtained. This would be valuable because it would make it possible to obtain data very early in future investigations of potentially suitable sites for a repository. This study compares laboratory electrical conductivity measurements with in-situ resistivity measurements from a borehole at Aespoe. The laboratory samples consist mainly of Aespoe diorite and fine-grained granite and the rock surrounding the borehole of Aespoe diorite, Smaaland granite and fine-grained granite. The comparison shows good agreement between laboratory measurements and in-situ data

Lithium and trace-element concentrations in trioctahedral micas from granites of different geochemical types measured via laser ablation ICP-MS

Czech Academy of Sciences Publication Activity Database

Breiter, Karel; Vaňková, M.; Vašinová Galiová, M.; Korbelová, Zuzana; Kanický, V.

2017-01-01

Roč. 81, č. 1 (2017), s. 15-33 ISSN 0026-461X R&D Projects: GA ČR GA14-13600S Institutional support: RVO:67985831 Keywords : trioctahedral micas * Li-mica * rare-metal granite * Bohemian Massif * laser ablation inductively coupled plasma mass spectrometry Subject RIV: DB - Geology ; Mineralogy OBOR OECD: Mineralogy Impact factor: 1.285, year: 2016

Decomposition of Composite Electric Field in a Three-Phase D-Dot Voltage Transducer Measuring System

Directory of Open Access Journals (Sweden)

Xueqi Hu

2016-10-01

Full Text Available In line with the wider application of non-contact voltage transducers in the engineering field, transducers are required to have better performance for different measuring environments. In the present study, the D-dot voltage transducer is further improved based on previous research in order to meet the requirements for long-distance measurement of electric transmission lines. When measuring three-phase electric transmission lines, problems such as synchronous data collection and composite electric field need to be resolved. A decomposition method is proposed with respect to the superimposed electric field generated between neighboring phases. The charge simulation method is utilized to deduce the decomposition equation of the composite electric field and the validity of the proposed method is verified by simulation calculation software. With the deduced equation as the algorithm foundation, this paper improves hardware circuits, establishes a measuring system and constructs an experimental platform for examination. Under experimental conditions, a 10 kV electric transmission line was tested for steady-state errors, and the measuring results of the transducer and the high-voltage detection head were compared. Ansoft Maxwell Stimulation Software was adopted to obtain the electric field intensity in different positions under transmission lines; its values and the measuring values of the transducer were also compared. Experimental results show that the three-phase transducer is characterized by a relatively good synchronization for data measurement, measuring results with high precision, and an error ratio within a prescribed limit. Therefore, the proposed three-phase transducer can be broadly applied and popularized in the engineering field.

Electric field measurement in the dielectric tube of helium atmospheric pressure plasma jet

NARCIS (Netherlands)

Sretenović, G.B.; Guaitella, O.; Sobota, A.; Krstić, I.B.; Kovačević, V.V.; Obradović, B.M.; Kuraica, M.M.

2017-01-01

The results of the electric field measurements in the capillary of the helium plasma jet are presented in this article. Distributions of the electric field for the streamers are determined for different gas flow rates. It is found that electric field strength in front of the ionization wave

Wet method for measuring starch gelatinization temperature using electrical conductivity.

Science.gov (United States)

Morales-Sanchez, E; Figueroa, J D C; Gaytan-Martínez, M

2009-09-01

The objective of the present study was to develop a method for obtaining the gelatinization temperature of starches by using electrical conductivity. Native starches from corn, rice, potato, and wheat were prepared with different proportions of water and heated from room temperature to 90 degrees C, in a device especially designed for monitoring the electrical conductivity as a function of temperature. The results showed a linear trend of the electrical conductivity with the temperature until it reaches the onset gelatinization temperature. After that point, the electrical conductivity presented an increment or decrement depending on the water content in the sample and it was related to starch swelling and gelatinization phenomena. At the end gelatinization temperature, the conductivity becomes stable and linear, indicating that there are no more changes of phase. The starch gelatinization parameter, which was evaluated in the 4 types of starches using the electrical conductivity, was compared with those obtained by using differential scanning calorimeter (DSC). The onset temperature at which the electrical conductivity increased or decreased was found to be similar to that obtained by DSC. Also, the final temperature at which the electrical conductivity returned to linearity matched the end gelatinization temperature of the DSC. Further, a wet method for measuring the onset, peak, and end gelatinization temperatures as a function of temperature using the electrical conductivity curves is presented for a starch-water suspension.

Nanocompuestos de P30T y Óxido de Grafeno para Aplicaciones Fotovoltáicas: Caracterización Física y Fisicoquímica

OpenAIRE

López-Mata, C.; Velasco Santos, C.; Martínez , A. L.; Aguilar, J. O.; Campos , J.; Zavala-Pimentel, J. M.

2012-01-01

Fueron incorporadas nanoestructuras de óxido de grafeno (GROX) en una matriz de poli-3-octiltiofeno (p30T). Se llevó a cabo la caracterización fisica y fisicoquímica de las nanoestructuras de GROX y de las mezclas obtenidas en forma de pelícu1as compuestas. Las técnicas de caracterización empleadas fueron: Infrarrojo por Transformada de Fourier (FTIR), espectroscopía Raman, Microscopía Electrónica de Transmisión (TEM, Transmision Electronic Microscopy), Microscopia de Fuerza Atómica (AFM, Ato...

Electrical conduction in 7 nm wires constructed on λ-DNA

International Nuclear Information System (INIS)

Lund, John; Dong Jianchun; Deng Zhaoxiang; Mao Chengde; Parviz, Babak A

2006-01-01

We examine the morphological and electrical characteristics of nanowires fabricated on DNA templates via palladium (Pd) reduction. λ-DNA molecules were stretched and aligned on a mica surface using a molecular combing technique, followed by an electroless deposition of palladium, resulting in formation of nanowires with nominal width of 7 nm. We investigated the size distribution of nanowires with atomic force microscopy and made electrical connections to the wires by metal evaporation through multiple shadow masks. Electrical characterization of the nanowires under various bias conditions, variable temperature, and with different contact metal work functions revealed a conduction mechanism resembling that of granular metals

The growth of sodium rough films on mica (0001) as determined by Helium Atom Scattering

DEFF Research Database (Denmark)

Gerlach, Rolf; Balzer, Frank; Rubahn, Horst-Günter

2001-01-01

, which is addressed to Na atoms that fill cleavage-induced holes in the mica surface. It provides a convenient means of calibrating the coverage of the surface. With increasing surface coverage Na clusters are formed on the mica surface. A broad angular distribution of the scattered Helium intensity......Elastic helium atom scattering (HAS) and linear optical extinction measurements are used to investigate the growth of sodium (Na) films on mica substrates in the surface temperature range between 90 and 300 K. At half a monolayer (ML) surface coverage we observe a maximum of scattered He intensity...... is observed with a coverage-independent angular width above eight monolayers coverage. From simultaneous optical extinction measurements we deduce that the clusters are oblate with a ratio of semiaxes perpendicular and parallel to the surface plane between 0.23 and 0.165....

Some mica-vermiculite alterations-relation to the exchange capacity

International Nuclear Information System (INIS)

Misak, N.Z.; Abdel-Gawad, A.S.; Maghrawy, H.B.; Shafik, A.; Sayyah, T.

1983-01-01

The effect of treatment of six Indian mica-vermiculite minerals with sodium cobaltinitrite (I) and NaCl+H 2 O 2 (II) with the aim of producing more vermiculite in the structure and thus a higher sorption capacity, was studied. The changes occuring in the minerals were followed by X-ray, TG, DTA, and chemical analyses. The measured Sr 2+ and Co 2+ capacities were in basic agreement with the detected changes that revealed generally a minor alteration due to treatment I and a considerable one but to treatment II. Treatment II increased tremendously the capacity of the main-mica minerals, having a very small capacity in the natural form, and made them suitable for use as potential ion exchangers

Química general II

OpenAIRE

Olba Torrent, Amparo

2018-01-01

El document forma part dels materials docents programats mitjançant l'ajut del Servei de Política Lingüística de la Universitat de València Temes de l'assignatura: Química general II del primer curs del Grau de Química Topics of the course: General Chemistry II in the first year of the Degree in Chemistry

Strength and strain anisotropy of olkiluoto mica gneiss

International Nuclear Information System (INIS)

Hakala, M.; Kuula, H.; Hudson, J.

2006-10-01

An anisotropy in the elastic moduli values of intact rock with a ratio of more than 1.3∼1.5 has been reported to have an effect on the calculated magnitudes and orientations of the in situ principal stress components as measured by the overcoring method. Work related to the on-going site investigation for a deep radioactive waste repository at the Olkiluoto site in Western Finland has shown that the migmatic mica gneiss is anisotropic which could therefore affect the interpretation of overcoring stress measurement results. This paper includes a summary of the theory of anisotropy concerning the intact rock moduli via the strain compliance matrix, a description of the core sample testing methods, and interpretation of results for the migmatic mica gneiss from two site investigation boreholes. In this case study, 19 specimens were tested and the results showed a modulus anisotropy of about 1.4. Because such anisotropy is high enough to produce significant errors in the estimation of the in situ principal stresses, it is recommended to take this into account in the interpretation of the stress measurement results, both in the context of the current work in Finland and in other projects where similar anisotropy is encountered. (orig.)

La enseñanza de la química desde la perspectiva de la Química Verde

Directory of Open Access Journals (Sweden)

Pía José González García

2016-06-01

Full Text Available La Química Verde, como área de investigación, se comprende como el desarrollo de metodologías para modificar los productos o procesos con la finalidad de reducir o eliminar los riesgos que existen para el medio ambiente y la salud. De este modo, permite proyectar líneas de investigación en la construcción de un conocimiento y enfoques didácticos de las ciencias, y  para ser considerada como parte de los programas Ministeriales. El objetivo del estudio fue conocer y comprender el significado que le otorgan los(as docentes del área a la Química Verde como perspectiva para su enseñanza. A partir de los discursos emanados por los docentes participantes del estudio, se construyeron 4 categorías, las cuales son: la Química Verde como: contexto para la enseñanza de la química, medio de apropiación significativo del aprendizaje de la química, motivadora de la conciencia ambiental y reflejo de la Institución y su relación con los docentes. The teaching of chemistry from the Green Chemistry perspective Green Chemistry (GC, as a research area, understood as the development of methodologies to modify products or processes in order to reduce or eliminate the risks posed to the environment and human health. Thus it is allowing research project lines in building knowledge and didactic approaches of the sciences, and to be considered as part of the ministerial programs. The objective of this study was to know and understand the significance given by teachers in the area to GC as a perspective for education. From the speeches issued by teachers participating in the study, four categories, was built. GC as: context for teaching chemistry, through significant learning chemistry appropriation, motivating environmental awareness and reflection of the institution and its relationship with teachers.  O ensino de química, na perspectiva da Química verde A Química verde, como área de investigação, é compreendida como o desenvolvimento de

Charge transfer to a dielectric target by guided ionization waves using electric field measurements

NARCIS (Netherlands)

Slikboer, E.T.; Garcia-Caurel, E.; Guaitella, O.; Sobota, A.

2017-01-01

A kHz-operated atmospheric pressure plasma jet is investigated by measuring charge transferred to a dielectric electro-optic surface (BSO crystal) allowing for the measurement of electric field by exploiting the Pockels effect. The electric field values, distribution of the surface discharge and

Atom interferometry experiments with lithium. Accurate measurement of the electric polarizability

International Nuclear Information System (INIS)

Miffre, A.

2005-06-01

Atom interferometers are very sensitive tools to make precise measurements of physical quantities. This study presents a measurement of the static electric polarizability of lithium by atom interferometry. Our result, α = (24.33 ± 0.16)*10 -30 m 3 , improves by a factor 3 the most accurate measurements of this quantity. This work describes the tuning and the operation of a Mach-Zehnder atom interferometer in detail. The two interfering arms are separated by the elastic diffraction of the atomic wave by a laser standing wave, almost resonant with the first resonance transition of lithium atom. A set of experimental techniques, often complicated to implement, is necessary to build the experimental set-up. After a detailed study of the atom source (a supersonic beam of lithium seeded in argon), we present our experimental atom signals which exhibit a very high fringe visibility, up to 84.5 % for first order diffraction. A wide variety of signals has been observed by diffraction of the bosonic isotope at higher diffraction orders and by diffraction of the fermionic less abundant isotope. The quality of these signals is then used to do very accurate phase measurements. A first experiment investigates how the atom interferometer signals are modified by a magnetic field gradient. An absolute measurement of lithium atom electric polarizability is then achieved by applying a static electric field on one of the two interfering arms, separated by only 90 micrometers. The construction of such a capacitor, its alignment in the experimental set-up and its operation are fully detailed.We obtain a very accurate phase measurement of the induced Lo Surdo - Stark phase shift (0.07 % precision). For this first measurement, the final uncertainty on the electric polarizability of lithium is only 0.66 %, and is dominated by the uncertainty on the atom beam mean velocity, so that a further reduction of the uncertainty can be expected. (author)

Spectroscopic measurement of the electric field in a helium plasma jet

NARCIS (Netherlands)

Hofmans, M.; Sobota, A.

2017-01-01

The electric field in a plasma jet is measured spectroscopically utilizing the Stark-effect. A cold atmospheric pressure helium plasma jet is used, which operates at a μs-pulsed applied voltage of 6 kV, a frequency of 5 kHz and with a helium flow of 1.5 slm. Due to the electric field in the jet, the

Electric field measurements at near-atmospheric pressure by coherent Raman scattering of laser beams

International Nuclear Information System (INIS)

Ito, Tsuyohito; Kobayashi, Kazunobu; Hamaguchi, Satoshi; Mueller, Sarah; Czarnetzki, Uwe

2010-01-01

Electric field measurements at near-atmospheric pressure environments based on electric-field induced Raman scattering are applied to repetitively pulsed nanosecond discharges. The results have revealed that the peak electric field near the centre of the gap is almost independent of the applied voltage. Minimum sustainable voltage measurements suggests that, at each discharge pulse, charged particles that remain from the previous pulse serve as discharge seeds and play an important role for generation of uniform glow-like discharges.

BIOÉTICA Y GENÓMICA BIOÉTICA E GENÔMICA BIOETHICS AND GENOMICS

Directory of Open Access Journals (Sweden)

José Alberto Mainetti

2003-01-01

Full Text Available Los avances científicos en el campo de la genómica abren las puertas a los fantasmas de la humanidad. Por esto, el Proyecto Genoma Humano (PGH ha sido el primer gran proyecto de investigación internacional que ha tenido un subproyecto sobre la problemática ética, legal y social asociada al mismo: Ethical, Legal, and Social Issues (ELSI. Esta preocupación bioética surgió como espacio de dilucidación de las diferentes preocupaciones éticas y sociales que nacían a la par de los avances de la genómica. La genómica, expresada como la clave que revelará el misterio del ser (la lámpara de Aladino o como la herramienta de destrucción ecológica, el determinismo genético, el reduccionismo genético y la eugenesia, es decir, como la caja de Pandora. El PGH posee un incalculable valor para el diagnóstico de nuevas enfermedades, nuevos fármacos y nuevas terapias, pero abre también riesgos y temores que han de ser estudiados y analizados desde una perspectiva más amplia que la científicotécnica, es decir, como una reflexión bioética sobre la genómicaOs avanços científicos no campo da genômica abrem as portas aos fantasmas da humanidade. Por isso, o Projeto Genoma Humano (PGH foi o primeiro grande projeto de pesquisa internacional que teve um subprojeto sobre a problemática ética, legal e social associada ao mesmo. Esta preocupação bioética surgiu como espaço de elucidação das diferentes preocupações éticas e sociais que surgiam ao par dos avanços da genômica. A genômica, expressa como a chave que revelará o mistério do ser ( a lâmpada de Aladim ou como a ferramenta de destruição ecológica, o determinismo gen´tico, o reducionismo genético e a eugenésia, isto é, como a caixa de Pandora. O PGH possui um incalculável valor para o diagnóstico de novas enfermidades, novos fármacos e novas terapias, porém abrem também riscos e temores que devem ser estudados e analisados numa perspectiva mais ampla que a

Evaluation of metal–nanowire electrical contacts by measuring contact end resistance

International Nuclear Information System (INIS)

Park, Hongsik; Beresford, Roderic; Xu, Jimmy; Ha, Ryong; Choi, Heon-Jin; Shin, Hyunjung

2012-01-01

It is known, but often unappreciated, that the performance of nanowire (NW)-based electrical devices can be significantly affected by electrical contacts between electrodes and NWs, sometimes to the extent that it is really the contacts that determine the performance. To correctly understand and design NW device operation, it is thus important to carefully measure the contact resistance and evaluate the contact parameters, specific contact resistance and transfer length. A four-terminal pattern or a transmission line model (TLM) pattern has been widely used to measure contact resistance of NW devices and the TLM has been typically used to extract contact parameters of NW devices. However, the conventional method assumes that the electrical properties of semiconducting NW regions covered by a metal are not changed after electrode formation. In this study, we report that the conventional methods for contact evaluation can give rise to considerable errors because of an altered property of the NW under the electrodes. We demonstrate that more correct contact resistance can be measured from the TLM pattern rather than the four-terminal pattern and correct contact parameters including the effects of changed NW properties under electrodes can be evaluated by using the contact end resistance measurement method. (paper)

Design of Electric Field Sensors for Measurement of Electromagnetic Pulse

Directory of Open Access Journals (Sweden)

Hui ZHANG

2014-01-01

Full Text Available In this paper, a D-dot electric field sensor and a fiber-optic transmission electric field sensor are developed for measurement of electromagnetic pulse. The D-dot sensor is a differential model sensor without source and has a simple structure. The fiber-optic transmission sensor is in the type of small dipole antenna, which uses its outside shielding layer as a pair of antennas. Design of the sensor circuit and the test system are introduced in this paper. A calibration system for these pulsed field sensors is established and the test results verified the ability of the developed sensors for measurement of the standard electromagnetic pulse field (the half peak width is 25 ns and the rising time is 2.5 ns.

CRIT II electric, magnetic, and density measurements within an ionizing neutral stream

Science.gov (United States)

Swenson, C. M.; Kelley, M. C.; Primdahl, F.; Baker, K. D.

1990-01-01

Measurements from rocket-borne sensors inside a high-velocity neutral barium beam show a-factor-of-six increase in plasma density in a moving ionizing front. This region was colocated with intense fluctuating electric fields at frequencies well under the lower hybrid frequency for a barium plasma. Large quasi-dc electric and magnetic field fluctuations were also detected with a large component of the current and the electric field parallel to B(0). An Alfven wave with a finite electric field component parallel to the geomagnetic field was observed to propagate along B(0), where it was detected by an instrumented subpayload.

Structure, surface morphology and electrical properties of evaporated Ni thin films: Effect of substrates, thickness and Cu underlayer

International Nuclear Information System (INIS)

Hemmous, M.; Layadi, A.; Guittoum, A.; Souami, N.; Mebarki, M.; Menni, N.

2014-01-01

Series of Ni thin films have been deposited by thermal evaporation onto glass, Si(111), Cu, mica and Al 2 O 3 substrates with and without a Cu underlayer. The Ni thicknesses, t, are in the 4 to 163 nm range. The Cu underlayer has also been evaporated with a Cu thickness equal to 27, 52 and 90 nm. The effects of substrate, the Ni thickness and the Cu underlayer on the structural and electrical properties of Ni are investigated. Rutherford Backscattering Spectroscopy was used to probe the Ni/Substrate and Ni–Cu underlayer interfaces and to measure both Ni and Cu thicknesses. The texture, the strain and the grain size values were derived from X-ray diffraction experiments. The surface morphology is studied by means of a Scanning Electron Microscope. The electrical resistivity is measured by the four point probe. The Ni films grow with the <111> texture on all substrates. The Ni grain sizes D increase with increasing thickness for the glass, Si and mica substrates and decrease for the Cu one. The strain ε is positive for low thickness, decreases in magnitude and becomes negative as t increases. With the Cu underlayer, the growth mode goes through two phases: first, the stress (grain size) increases (decreases) up to a critical thickness t Cr , then stress is relieved and grain size increases. All these results will be discussed and correlated. - Highlights: • The structural and electrical properties of evaporated Ni thin films are studied. • The effect of thickness, substrates and Cu underlayer is investigated. • Texture, grain size, strain and surface morphology are discussed. • Growth modes are described as a function of Ni thickness

Nucleation and crystallization behaviors of nano-crystalline lithium–mica glass–ceramic prepared via sol–gel method

Energy Technology Data Exchange (ETDEWEB)

Tohidifar, M.R. [Department of Materials Science and Engineering, Tarbiat Modares University, P.O. Box 14115-143, Tehran (Iran, Islamic Republic of); Alizadeh, P., E-mail: p-alizadeh@modares.ac.ir [Department of Materials Science and Engineering, Tarbiat Modares University, P.O. Box 14115-143, Tehran (Iran, Islamic Republic of); Riello, P. [Department of Molecular Sciences and Nanosystems, University of Ca’Foscari, Venice (Italy)

2012-06-15

Graphical abstract: The effects of nucleation and crystallization treatments on nano-crystalline lithium–mica glass–ceramic, synthesized by sol–gel technique, were investigated. It was found that MgF{sub 2} crystals act as nuclei centers for the mica crystallization so that a large quantity of mica crystallites was obtained following nucleation process. The crystallization activation energy for both the un-nucleated and nucleated samples was measured as 400.2 and 229.6 kJ mol{sup −1}, respectively. The calculated Avrami exponents demonstrated that the growth mechanism of mica crystallites changes from the needle-like to three-dimensional growth with applying the appropriate nucleation treatment ▪. Highlights: ► Crystallization temperature shifts to 625 from 680 °C following nucleation process. ► Activation energy of crystallization for the nucleated specimen is 229.6 kJ mol{sup −1}. ► Crystallization activation energy for the un-nucleated specimen is 400.2 kJ mol{sup −1}. ► Needle-like growth is predominant growth mechanism for un-nucleated sample. ► Three-dimensional growth is predominant growth mechanism for nucleated sample. -- Abstract: The paper investigates the effects of nucleation and crystallization treatments on nano-crystalline lithium–mica glass–ceramics, taking the composition LiMg{sub 3}AlSi{sub 3(1+x)}O{sub 10+6x}F{sub 2} (x = 0.5) and 8 mass% MgF{sub 2} synthesized by sol–gel technique. Here, X-ray diffraction, thermal analysis and transmission electron microscopy were used to assess the structural evolutions of as-synthesized nano-crystalline lithium–mica glass–ceramics. It was found that MgF{sub 2} crystals perform as nuclei centers for the mica crystallization hence; a large quantity of mica crystallites obtained following the nucleation process at 400 °C for 12 h. For both the un-nucleated and nucleated samples, the crystallization activation energy was measured as 400.2 and 229.6 kJ mol{sup −1

Atomically flat platinum films grown on synthetic mica

Science.gov (United States)

Tanaka, Hiroyuki; Taniguchi, Masateru

2018-04-01

Atomically flat platinum thin films were heteroepitaxially grown on synthetic fluorophlogopite mica [KMg3(AlSi3O10)F2] by van der Waals epitaxy. Platinum films deposited on a fluorophlogopite mica substrate by inductively coupled plasma-assisted sputtering with oxygen introduction on a synthetic mica substrate resulted in the growth of twin single-crystalline epitaxial Pt(111) films.

Magneto-acousto-electrical Measurement Based Electrical Conductivity Reconstruction for Tissues.

Science.gov (United States)

Zhou, Yan; Ma, Qingyu; Guo, Gepu; Tu, Juan; Zhang, Dong

2018-05-01

Based on the interaction of ultrasonic excitation and magnetoelectrical induction, magneto-acousto-electrical (MAE) technology was demonstrated to have the capability of differentiating conductivity variations along the acoustic transmission. By applying the characteristics of the MAE voltage, a simplified algorithm of MAE measurement based conductivity reconstruction was developed. With the analyses of acoustic vibration, ultrasound propagation, Hall effect, and magnetoelectrical induction, theoretical and experimental studies of MAE measurement and conductivity reconstruction were performed. The formula of MAE voltage was derived and simplified for the transducer with strong directivity. MAE voltage was simulated for a three-layer gel phantom and the conductivity distribution was reconstructed using the modified Wiener inverse filter and Hilbert transform, which was also verified by experimental measurements. The experimental results are basically consistent with the simulations, and demonstrate that the wave packets of MAE voltage are generated at tissue interfaces with the amplitudes and vibration polarities representing the values and directions of conductivity variations. With the proposed algorithm, the amplitude and polarity of conductivity gradient can be restored and the conductivity distribution can also be reconstructed accurately. The favorable results demonstrate the feasibility of accurate conductivity reconstruction with improved spatial resolution using MAE measurement for tissues with conductivity variations, especially suitable for nondispersive tissues with abrupt conductivity changes. This study demonstrates that the MAE measurement based conductivity reconstruction algorithm can be applied as a new strategy for nondestructive real-time monitoring of conductivity variations in biomedical engineering.

Towards completely miscible PMMA nanocomposites reinforced by shear-stiff, nano-mica.

Science.gov (United States)

Ziadeh, Mazen; Weiss, Stephan; Fischer, Bianca; Förster, Stephan; Altstädt, Volker; Müller, Axel H E; Breu, Josef

2014-07-01

Optimizing the reinforcement of polymers with nanoplatelets requires optimization of the aspect ratio and the moduli of the filler while providing a complete stress transfer. Employing a novel shear-stiff, nano-mica with large aspect ratio, we focus on maximizing the interfacial interaction between filler and matrix. External surfaces of the nano-mica were selectively modified by a polycationic macro-initiator and two PMMA-polymer brushes of length below and above critical entanglement length, respectively, and the mechanical properties of the three PMMA nanocomposites were measured. The multiple electrostatic anchoring groups of the macro-initiator not only provide reliable adhesion but at the same time allow the variation of the degree of protonation providing a local match between the charge densities of the clay surface and the adsorbed macro-initiator. PMMA coating of the nano-mica via surface initiated polymerization yielded long-term stable suspensions in THF that showed birefringence of a nematic phase. Solution blending of the PMMA coated nano-mica allows for dispersing single clay tactoids in the translucent PMMA nanocomposites at 5 wt% clay loading as determined by transmission electron microscopy (TEM). Although significantly improved mechanical properties could be achieved as compared to nanocomposites made with conventional clay fillers, the full potential - as expressed by Halpin-Tsai equations - of the PMMA coated nano-mica can still not be completely utilized. This is attributed to the non-wetting character of the densely packed PMMA brushes attached to planar nanoplatelets. Copyright © 2014 Elsevier Inc. All rights reserved.

Procedures for measuring the electrical properties of superconductors for accelerator magnets

International Nuclear Information System (INIS)

Sampson, W.B.

1986-01-01

There are three important electrical properties associated with the superconductor used to fabricate accelerator magnets. The most important is the critical current since this determines the performance potential of the magnet. The normal state resistivity and the volume magnetization are the other principal electrical parameters. In this report methods for measuring these parameters are presented and procedures for including self field effect and magnetoresistance are discussed

Influence of plant roots on electrical resistivity measurements of cultivated soil columns

Science.gov (United States)

Maloteau, Sophie; Blanchy, Guillaume; Javaux, Mathieu; Garré, Sarah

2016-04-01

Electrical resistivity methods have been widely used for the last 40 years in many fields: groundwater investigation, soil and water pollution, engineering application for subsurface surveys, etc. Many factors can influence the electrical resistivity of a media, and thus influence the ERT measurements. Among those factors, it is known that plant roots affect bulk electrical resistivity. However, this impact is not yet well understood. The goals of this experiment are to quantify the effect of plant roots on electrical resistivity of the soil subsurface and to map a plant roots system in space and time with ERT technique in a soil column. For this research, it is assumed that roots system affect the electrical properties of the rhizosphere. Indeed the root activity (by transporting ions, releasing exudates, changing the soil structure,…) will modify the rhizosphere electrical conductivity (Lobet G. et al, 2013). This experiment is included in a bigger research project about the influence of roots system on geophysics measurements. Measurements are made on cylinders of 45 cm high and a diameter of 20 cm, filled with saturated loam on which seeds of Brachypodium distachyon (L.) Beauv. are sowed. Columns are equipped with electrodes, TDR probes and temperature sensors. Experiments are conducted at Gembloux Agro-Bio Tech, in a growing chamber with controlled conditions: temperature of the air is fixed to 20° C, photoperiod is equal to 14 hours, photosynthetically active radiation is equal to 200 μmol m-2s-1, and air relative humidity is fixed to 80 %. Columns are fully saturated the first day of the measurements duration then no more irrigation is done till the end of the experiment. The poster will report the first results analysis of the electrical resistivity distribution in the soil columns through space and time. These results will be discussed according to the plant development and other controlled factors. Water content of the soil will also be detailed

Development and application of measurement techniques for evaluating localised magnetic properties in electrical steel

Science.gov (United States)

Lewis, N. J.; Anderson, P. I.; Gao, Y.; Robinson, F.

2018-04-01

This paper reports the development of a measurement probe which couples local flux density measurements obtained using the needle probe method with the local magnetising field attained via a Hall effect sensor. This determines the variation in magnetic properties including power loss and permeability at increasing distances from the punched edge of 2.4% and 3.2% Si non-oriented electrical steel sample. Improvements in the characterisation of the magnetic properties of electrical steels would aid in optimising the efficiency in the design of electric machines.

Rocket measurements within a polar cap arc: Plasma, particle, and electric circuit parameters

International Nuclear Information System (INIS)

Weber, E.J.; Ballenthin, J.O.; Basu, S.; Carlson, H.C.; Hardy, D.A.; Maynard, N.C.; Smiddy, M.; Kelley, M.C.; Fleischman, J.R.; Sheehan, R.E.; Pfaff, R.F.; Rodriguez, P.

1989-01-01

An instrumented rocket payload was launched into a polar cap F layer aurora to investigate the energetic particle, plasma, and electric circuit parameters of a Sun-aligned arc. On-board instruments measured energetic electron flux, ion composition and density fluctuations, electron density and temperature, electron density fluctuations, and ac and dc electric fields. Real-time all-sky imaging photometer measurements of the location and motion of the aurora, were used to determine the proper geophysical situation for launch. Comparison of the in situ measurements with remote optical measurements shows that the arc was produced by fluxes of low-energy (< 1 keV) electrons. Field-aligned potentials in the arc inferred from the electron spectra had a maximum value of approximately 300 V, and from the spectral shape a parent population of preaccelerated electrons characteristic of the boundary plasma sheet or magnetosheath was inferred. Electric field components along and across the arc show sunward flow within the arc and duskward drift of the arc consistent with the drift direction and speed determined from optical imaging. Thus this arc is drifting duskward under the influence of the convection electric field. Three possible explanations for this (field-aligned currents, chemistry, and transport) are considered. Finally, ionospheric irregularity and electric field fluctuations indicate two different generation mechanisms on the dawnside and duskside of the arc. On the duskside, parameters are suggestive of an interchange process, while on the dawnside, fluctuation parameters are consistent with a velocity shear instability

Vibrations measurement at the Embalse nuclear power plant's electrical generator

International Nuclear Information System (INIS)

Salomoni, R.C.; Belinco, C.G.; Pastorini, A.J.; Sacchi, M.A.

1987-01-01

After the modifications made at the Embalse nuclear power plant's electrical generator to reduce its vibration level produced by electromagnetic phenomena, it was necessary to perform measurements at the new levels, under different areas and power conditions. To this purpose, a work was performed jointly with the 'Vibrations Team' of the ANSALDO Company (the generator constructor) and the Hydrodynamic Assays Division under the coordination and supervision of the plant's electrical maintenance responsible. This paper includes the main results obtained and the instrumentation criteria and analysis performed. (Author)

Malvaceae endémicas del Perú

Directory of Open Access Journals (Sweden)

Magda Chanco

2013-10-01

Full Text Available La familia Malvaceae es reconocida en el Perú con 38 géneros y 264 especies (Brako & Zarucchi 1993, Ulloa et al. 2004, mayormente arbustos y hierbas. En este trabajo reconocemos 87 especies endémicas en 16 géneros. El género más rico en especies endémicas es Nototriche. Las especies endémicas se encuentran en varias regiones ecológicas, entre ellas Altoandina, Mesoandina y Puna Húmeda y Seca, por encima de los 2500 m, hasta alcanzar los límites de la vegetación a 5100 m de altitud. Se aplicaron las categorías y criterios de la UICN a 84 especies. Once especies endémicas se encuentran presentes en el Sistema Nacional de Áreas Naturales Protegidas por el Estado.

CT-scan-monitored electrical-resistivity measurements show problems achieving homogeneous saturation

International Nuclear Information System (INIS)

Sprunt, E.S.; Davis, R.M.; Muegge, E.L.; Desai, K.P.

1991-01-01

This paper reports on x-ray computerized tomography (CT) scans obtained during measurement of the electrical resistivity of core samples which revealed some problems in obtaining uniform saturation along the lengths of the samples. The electrical resistivity of core samples is measured as a function of water saturation to determine the saturation exponent used in electric-log interpretation. An assumption in such tests is that the water saturation is uniformly distributed. Failure of this assumption can result in errors in the determination of the saturation exponent. Three problems were identified in obtaining homogeneous water saturation in two samples of a Middle Eastern carbonate grainstone: a stationary front formed in one sample at 1-psi oil/brine capillary pressure, a moving front formed at oil/brine capillary pressure ≤4 psi in samples tested in fresh mixed-wettability and cleaned water-wet states, and the heterogeneous fluid distribution caused by a rapidly moving front did not dissipate when the capillary pressure was eliminated in the samples

Vochysiaceae endémicas del Perú

Directory of Open Access Journals (Sweden)

Blanca León

2013-10-01

Full Text Available La familia Vochysiaceae es reconocida en el Perú por presentar cuatro géneros y 32 especies (Brako & Zarucchi, 1993; Ulloa Ulloa et al., 2004, todas árboles. En este trabajo reconocemos dos especies endémicas en el género Qualea. Estas especies endémicas han sido encontradas en la región Bosques Húmedos Amazónicos, entre los 100 y 160 m de altitud. Ninguna especie endémica se encuentra representada dentro del Sistema Nacional de Áreas Naturales Protegidas por el Estado.

Measurement of DC electrical conductivity of alumina during spallation-neutron irradiation

International Nuclear Information System (INIS)

Farnum, E.H.; Clinard, F.W. Jr.; Kennedy, J.C. III; Sommer, W.F.; Dammeyer, M.D.

1993-01-01

An irradiation experiment was carried out during the summer of 1992 at the Los Alamos Spallation Radiation Effects Facility (LASREF). In situ measurements of electrical conductivity in alumina, sapphire and mineral-insulated electrical cables were made at 640 degrees C, 590 degrees C and 400 degrees C. Both DC and AC (100 Hz to 1 MHz) measurements were made to fluence of approximately 3 x 10 23 n/m 2 . Optical absorption from 200 nm to 800 nm was measured in pure silica - and OH-doped silica-core optical fibers during the irradiation. A large number of passive samples were included in the irradiation, some at the furnace temperatures and some at ambient temperature. This report describes preliminary analysis of the DC conductivity measurements. The AC measurements are analyzed in the companion report. All samples are being recovered for post-irradiation examination as this report is being written in May, 1993. Final analysis of the conductivity data awaits the results of measured fluence from activation foils and will be published at ICFRM-6

Features of measurement and processing of vibration signals registered on the moving parts of electrical machines

OpenAIRE

Gyzhko, Yuri

2011-01-01

Measurement and processing of vibration signals registered on the moving parts of the electrical machines using the diagnostic information-measuring system that uses Bluetooth wireless standard for the transmission of the measured data from moving parts of electrical machine is discussed.

Mechanistic Indicators of Childhood Asthma (MICA) Study

Science.gov (United States)

The Mechanistic Indicators of Childhood Asthma (MICA) Study has been designed to incorporate state-of-the-art technologies to examine the physiological and environmental factors that interact to increase the risk of asthmatic responses. MICA is primarily a clinically-bases obser...

EDM: Neutron electric dipole moment measurement

Directory of Open Access Journals (Sweden)

Peter Fierlinger

2016-02-01

Full Text Available An electric dipole moment (EDM of the neutron would be a clear sign of new physics beyond the standard model of particle physics. The search for this phenomenon is considered one of the most important experiments in fundamental physics and could provide key information on the excess of matter versus antimatter in the universe. With high measurement precision, this experiment aims to ultimately achieve a sensitivity of 10-28 ecm, a 100-fold improvement in the sensitivity compared to the state-of-the-art. The EDM instrument is operated by an international collaboration based at the Technische Universität München.

Concept for a MEMS-type vacuum sensor based on electrical conductivity measurements

Directory of Open Access Journals (Sweden)

F. J. Giebel

2017-11-01

Full Text Available The concept of the micro-structured vacuum sensor presented in this article is the measurement of the electrical conductivity of thinned gases in order to develop a small, economical and quite a simple type of vacuum sensor. There are already some approaches for small vacuum sensors. Most of them are based on conservative measurement principles similar to those used in macroscopic vacuum gauges. Ionization gauges use additional sources of energy, like hot cathodes, ultraviolet radiation or high voltage for example, for ionizing gas molecules and thereby increasing the number of charge carriers for measuring low pressures. In contrast, the concept discussed here cannot be found in macroscopic sensor systems because it depends on the microscopic dimension of a gas volume defined by two electrodes. Here we present the concept and the production of a micro-structured vacuum sensor chip, followed by the electrical characterization. Reference measurements with electrodes at a distance of about 1 mm showed currents in the size of picoampere and a conductivity depending on ambient pressure. In comparison with these preliminary measurements, fundamental differences regarding pressure dependence of the conductivity are monitored in the electrical characterization of the micro-structured sensor chip. Finally the future perspectives of this sensor concept are discussed.

Bienestar, actividad económica y cuentas nacionales. Reflexiones en torno al concepto de trabajo productivo Bienestar, actividad económica y cuentas nacionales. Reflexiones en torno al concepto de trabajo productivo

Directory of Open Access Journals (Sweden)

Sergio Cámara Izquierdo

2008-12-01

Full Text Available La medición de la actividad económica es fundamental para analizar el bienestar material de la sociedad y la dinámica económica. Sin embargo, no existe un criterio único para realizar esta medición, dadas las discrepancias en la definición del concepto de trabajo productivo entre y al interior de los distintos paradigmas económicos. Por un lado, la teoría ortodoxa concibe la producción como un proceso físico o material, como producción de bienes y servicios. Como consecuencia de la amplitud de esta definición, incurre en una serie de inconsistencias en sus planteamientos prácticos sobre la medición de la actividad económica, por lo que fracasa en su intento de servir como medida del bienestar. Además, al mezclar flujos productivos de muy distinta índole, frustra su utilidad para el análisis de la dinámica económica. Por otro lado, la teoría laboral del valor tiene un concepto de trabajo productivo coherente, a pesar de las controversias suscitadas en más de un siglo de debates, basado en una concepción de la producción históricamente específica; aunque esta limitación le impide fundamentar el análisis del bienestar, es útil para el análisis de la dinámica económica. La última parte del artículo discute las transformaciones necesarias para convertir las categorías contables ortodoxas en categorías acordes con la teoría laboral del valor. La comparación de ambas categorías para España entre 1954 y 2006 evidencia importantes diferencias en la medición del crecimiento económico y la distribución de la renta.The measurement of economic activity is central for the analysis of material welfare and economic dynamics. Nonetheless, there is not a single criterion for this measurement, given the discrepancies on the definition of the concept of productive labour among and within the various economic paradigms. On the one hand, orthodox theory conceives production as a physical or material process, as production

Precision measurement of electric organ discharge timing from freely moving weakly electric fish.

Science.gov (United States)

Jun, James J; Longtin, André; Maler, Leonard

2012-04-01

Physiological measurements from an unrestrained, untethered, and freely moving animal permit analyses of neural states correlated to naturalistic behaviors of interest. Precise and reliable remote measurements remain technically challenging due to animal movement, which perturbs the relative geometries between the animal and sensors. Pulse-type electric fish generate a train of discrete and stereotyped electric organ discharges (EOD) to sense their surroundings actively, and rapid modulation of the discharge rate occurs while free swimming in Gymnotus sp. The modulation of EOD rates is a useful indicator of the fish's central state such as resting, alertness, and learning associated with exploration. However, the EOD pulse waveforms remotely observed at a pair of dipole electrodes continuously vary as the fish swims relative to the electrodes, which biases the judgment of the actual pulse timing. To measure the EOD pulse timing more accurately, reliably, and noninvasively from a free-swimming fish, we propose a novel method based on the principles of waveform reshaping and spatial averaging. Our method is implemented using envelope extraction and multichannel summation, which is more precise and reliable compared with other widely used threshold- or peak-based methods according to the tests performed under various source-detector geometries. Using the same method, we constructed a real-time electronic pulse detector performing an additional online pulse discrimination routine to enhance further the detection reliability. Our stand-alone pulse detector performed with high temporal precision (<10 μs) and reliability (error <1 per 10(6) pulses) and permits longer recording duration by storing only event time stamps (4 bytes/pulse).

The Epitaxial Growth of Self-Assembled Ternaphthalene Fibers on Muscovite Mica

NARCIS (Netherlands)

Simbrunner, C.; Schwabegger, G.; Resel, R.; Dingemans, T.J.; Sitter, H.

2014-01-01

The morphology and structure of 2,2':6',2?-ternaphthalene (NNN) deposited on muscovite mica(001) substrates was investigated by scanning force microscopy (SFM) and specular X-ray diffraction measurements. Consistently, both methods reveal the coexistence of needle-like structures with a {111}

Contribution of soil electric resistivity measurements to the studies on soil/grapevine water relations

Directory of Open Access Journals (Sweden)

Etienne Goulet

2006-06-01

Full Text Available The classical techniques that allow to quantify the soil water status such as the gravimetric method or the use of neutrons probes do not give access to the volume of soil explored by the plant root system. On the contrary, electric tomography can be used to have a global vision on the water exchange area between soil and plant. The measurement of soil electric resistivity, as a non destructive, spatially integrative technique, has recently been introduced into viticulture. The use of performing equipment and adapted software allows for rapid data processing and gives the possibility to spatialize the variations of soil texture or humidity in two or three dimensions. Soil electric resistivity has been tested for the last three years at the Experimental Unit on Grapevine and Vine, INRA, Angers, France, to study the water supply to the vine in different “terroir” conditions. Resistivity measurements were carried out with the resistivity meter Syscal R1+ (Iris Instruments, France equipped with 21 electrodes. Those electrodes were lined up on the soil surface in a direction perpendiculary to 5 grapevine rows with an electrode spacing of 0.5 m. and a dipole-dipole arrangement. Resistivity measurements were performed on the same place at different times in order to study soil moisture variations. This experimental set up has permitted to visualise the soil stratification and individualize some positive electric anomalies corresponding to preferential drying ; this desiccation could be attributed to grapevine root activity. The soil bulk subject to the water up-take could be defined more precisely and in some types of soil, available water may even be quantified. Terroir effect on grapevine root activity has also been shown up on two different experimental parcels through electric tomography and first results indicate that it is possible to monitor the effects of soil management (inter-row grassing or different rootstocks on the water supply to the

Influence and Correction from the Human Body on the Measurement of a Power-Frequency Electric Field Sensor

Directory of Open Access Journals (Sweden)

Dongping Xiao

2016-06-01

Full Text Available According to the operating specifications of existing electric field measuring instruments, measuring technicians must be located far from the instruments to eliminate the influence of the human body occupancy on a spatial electric field. Nevertheless, in order to develop a portable safety protection instrument with an effective electric field warning function for working staff in a high-voltage environment, it is necessary to study the influence of an approaching human body on the measurement of an electric field and to correct the measurement results. A single-shaft electric field measuring instrument called the Type LP-2000, which was developed by our research team, is used as the research object in this study. First, we explain the principle of electric field measurement and describe the capacitance effect produced by the human body. Through a theoretical analysis, we show that the measured electric field value decreases as a human body approaches. Their relationship is linearly proportional. Then, the ratio is identified as a correction coefficient to correct for the influence of human body proximity. The conclusion drawn from the theoretical analysis is proved via simulation. The correction coefficient kb = 1.8010 is obtained on the basis of the linear fitting of simulated data. Finally, a physical experiment is performed. When no human is present, we compare the results from the Type LP-2000 measured with Narda EFA-300 and the simulated value to verify the accuracy of the Type LP-2000. For the case of an approaching human body, the correction coefficient kb* = 1.9094 is obtained by comparing the data measured with the Type LP-2000 to the simulated value. The correction coefficient obtained from the experiment (i.e., kb* is highly consistent with that obtained from the simulation (i.e., kb. Two experimental programs are set; under these programs, the excitation voltages and distance measuring points are regulated to produce different

Influence and Correction from the Human Body on the Measurement of a Power-Frequency Electric Field Sensor.

Science.gov (United States)

Xiao, Dongping; Liu, Huaitong; Zhou, Qiang; Xie, Yutong; Ma, Qichao

2016-06-10

According to the operating specifications of existing electric field measuring instruments, measuring technicians must be located far from the instruments to eliminate the influence of the human body occupancy on a spatial electric field. Nevertheless, in order to develop a portable safety protection instrument with an effective electric field warning function for working staff in a high-voltage environment, it is necessary to study the influence of an approaching human body on the measurement of an electric field and to correct the measurement results. A single-shaft electric field measuring instrument called the Type LP-2000, which was developed by our research team, is used as the research object in this study. First, we explain the principle of electric field measurement and describe the capacitance effect produced by the human body. Through a theoretical analysis, we show that the measured electric field value decreases as a human body approaches. Their relationship is linearly proportional. Then, the ratio is identified as a correction coefficient to correct for the influence of human body proximity. The conclusion drawn from the theoretical analysis is proved via simulation. The correction coefficient kb = 1.8010 is obtained on the basis of the linear fitting of simulated data. Finally, a physical experiment is performed. When no human is present, we compare the results from the Type LP-2000 measured with Narda EFA-300 and the simulated value to verify the accuracy of the Type LP-2000. For the case of an approaching human body, the correction coefficient kb* = 1.9094 is obtained by comparing the data measured with the Type LP-2000 to the simulated value. The correction coefficient obtained from the experiment (i.e., kb*) is highly consistent with that obtained from the simulation (i.e., kb). Two experimental programs are set; under these programs, the excitation voltages and distance measuring points are regulated to produce different electric field

Electrical and calorimetric measurements and related software

CERN Document Server

Catalan-Lasheras, N; Koratzinos, M; Rijllart, A; Siemko, A; Strait, J; Tavian, L; Wolf, R

2009-01-01

During the incident of sector 3-4 on September 19th, the temperature of a number of magnets increased over the expected values prior to the circuit failure. A review of the data logged during powering tests on all circuits indicated potential resistive splices in sectors 1-2 and 6-7. Calorimetric and electrical measurements confirmed a high resistance in magnet B16. R1 and B32R6. Systematic measurements have been performed in other cold sectors of the LHC during which the temperature increase and voltage across magnets were acquired at different currents. Cryogenic subsectors on which the temperature increase was abnormal were equipped with precise voltmeters to detect eventual resistive splices in the bus-bars. The findings of the measurement campaign will be shown as well as the plans to implement similar diagnostics as a routine check prior to powering the superconducting circuits of the LHC.

RECUBRIMIENTOS DE VC Y NBC PRODUCIDOS POR DRT: TECNOLOGÍA ECONÓMICA, EFICIENTE Y AMBIENTALMENTE LIMPIA

Directory of Open Access Journals (Sweden)

Fabio Enrique Castillejo Nieto

2012-01-01

Full Text Available En este artículo se presentan los fundamentos del proceso de deposición por difusión termoreactiva (dtrdtrdtr, una técnica que permite producir recubrimientos duros de forma económica sin ser invasiva o agresiva con el medio ambiente. Se propone una metodología experimental para desarrollar recubrimientos de carburos de vanadio (vcvc, y carburos de niobio (NbC, sobre aceros aisi H13, utilizando en el proceso de fabricación DRT, bórax fundido, aluminio y ferroaleaciones a 1.020°C durante cuatro horas. Las muestras obtenidas fueron evaluadas utilizando difracción de rayos X (drdrx, para identificar las fases y microscopía electrónica de barrido (sem, para medir el espesor y la homogeneidad de los recubrimientos producidos. La dureza fue obtenida usando microdureza knoop con una carga de 50 g y la resistencia a la corrosión fue determinada con técnicas electroquímicas, utilizando polarización potenciodímica. Los resultados confirmaron la presencia de recubrimientos de carburo de vanadio y carburo niobio con buena regularidad en el espesor, altas durezas y una mejora en la resistencia a la corrosión en comparación con el acero sin recubrimiento.

In situ adsorption of bovine submaxillary mucin at the mica/aqueous solution interface

International Nuclear Information System (INIS)

Perez, E.; Proust, J.E.; Baszkin, A.; Boissonnade, M.M.

1984-01-01

An in situ adsorption measurement method at the mica/protein solution interface is described. An apparatus especially constructed for this purpose permits direct and continuous measurement of total adsorption (reversible and irreversible) of 14 C-labelled proteins. Bovine submaxillary mucin (BSM), extracted from salivary glands, was acetylated with (CH 3 14 CO) 2 O. The results show the increase of BSM adsorbed on mica surfaces with its concentration in solution and adsorption time. Pseudo plateaux are obtained for all concentrations studied, indicating the formation of thick layers. The loosely bound fraction of adsorbed mucin is proportional to the bulk concentration in solution. The amount of BSM adsorbed increases in the neighbourhood of the isoelectric point of BSM (pH 3). (Auth.)

Thermal and Electrical Conductivity Measurements of CDA 510 Phosphor Bronze

Science.gov (United States)

Tuttle, James E.; Canavan, Edgar; DiPirro, Michael

2009-01-01

Many cryogenic systems use electrical cables containing phosphor bronze wire. While phosphor bronze's electrical and thermal conductivity values have been published, there is significant variation among different phosphor bronze formulations. The James Webb Space Telescope (JWST) will use several phosphor bronze wire harnesses containing a specific formulation (CDA 510, annealed temper). The heat conducted into the JWST instrument stage is dominated by these harnesses, and approximately half of the harness conductance is due to the phosphor bronze wires. Since the JWST radiators are expected to just keep the instruments at their operating temperature with limited cooling margin, it is important to know the thermal conductivity of the actual alloy being used. We describe an experiment which measured the electrical and thermal conductivity of this material between 4 and 295 Kelvin.

The artificially injected charged particles as a tool for the measurement of the electric field in the magnetosphere

International Nuclear Information System (INIS)

Pirre, M.

1982-01-01

This chapter discusses two methods of measuring the parallel electric field using artificially injected charged particles. The first method uses electrons to measure the parallel electric field in the vicinity of the spacecraft. The second method uses ions to measure electric potential along the magnetic field lines if the associated parallel electric field is directed downward. The use of electrons for the measurement has many limitations due to the disturbed regions surrounding the spacecraft and to the high level of turbulence which could significantly reduce accuracy. Even if the parallel electric fields are too low to be measured owing to the broadening of the fluxes by turbulence, the electrons can still be used to study the turbulence. It is demonstrated that if parallel electric fields are predominantly directed upward at high altitude, a downward parallel electric field can exist at lower altitude. Lithium ions can be used to maximize the returning fluxes and to increase the probability of detection. Rockets are shown to be more suitable than satellites with regard to measurement

Electric heating systems - Measures and options for the reduction of electricity consumption; Elektroheizungen Massnahmen und Vorgehensoptionen zur Reduktion des Stromverbrauchs

Energy Technology Data Exchange (ETDEWEB)

Nipkow, J.; Togni, G.

2009-10-15

This final report for the Swiss Federal Office of Energy (SFOE) takes a look at how electricity consumption for electrical heating systems can be reduced. The authors state that electric space heating consumes roughly 6% to 12% of Swiss electricity consumption, depending on the source of data. Important reduction potentials obtainable through the implementation of efficiency measures and substitution are well known. The results of two surveys on hardware installations and heating users' and utility companies' preferences are presented and discussed. The user survey yielded more than 900 evaluable answers. The main focus was on conditions considered necessary for changing a heating system. The utilities' survey was carried out by means of letters posted to 62 utilities, half of whom sent back evaluable answers. The main focus was on the number of dwellings supplied with electric space heating, current and past tariffs and utility activities to motivate customers to change their heating systems. The results showed that high investments necessary for a new heating system and additional thermal insulation of the building are the main obstacles for making changes. On the basis of the project's findings, a catalogue of measures was developed, whereby financial aspects and general conditions were taken into account.

Measuring the vertical electrical field above an oceanic convection system using a meteorological sounding balloon

Science.gov (United States)

Chen, A. B.; Chiu, C.; Lai, S.; Chen, C.; Kuo, C.; Su, H.; Hsu, R.

2012-12-01

The vertical electric field above thundercloud plays an important role in the generation and modeling of transient luminous events. For example, Pasko [1995] proposed that the high quasi-static E-field following the positive cloud-to-ground lightning could accelerate and input energy to ambient electrons; as they collide and excite nitrogen and oxygen molecules in upper atmosphere, sprites may be induced. A series of balloon experiments led by Holzworth have investigated the temporal and spatial fluctuations of the electric field and conductivity in the upper atmosphere at different sites [Holzworth 2005, and references in]. But the strength and variation of the vertical electric field above thundercloud, especially oceanic ones, are not well documented so far. A lightweight, low-cost measurement system including an electric field meter and the associated aviation electronics are developed to carry out the in-situ measurement of the vertical electric field and the inter-cloud charge distribution. Our measuring system was first deployed using a meteorological sounding balloon from Taitung, Taiwan in May 2012. The measured electric field below 3km height shows an exponential decay and it is consistent with the expected potential gradient variation between ionosphere and the Earth surface. But the background strength of the measured E-field grows up exponentially and a violent fluctuations is also observed when the balloon flew over a developing oceanic convection cell. The preliminary results from this flight will be reported and discussed. This low-cost electric field meter is developed within one year. In the coming months, more flights will be performed with the aim to measure the rapid variation of the electric field above thundercloud as well as the E-field that may induce transient luminous events. Our ground campaigns show that the occurrence rates of blue and gigantic jet are relatively high in the vicinity of Taiwan. Our experiment can be used to diagnose

In-situ measurement of the electrical conductivity of aluminum oxide in HFIR

Energy Technology Data Exchange (ETDEWEB)

Zinkle, S.J.; White, D.P.; Snead, L.L. [Oak Ridge National Lab., TN (United States)] [and others

1996-10-01

A collaborative DOE/Monbusho irradiation experiment has been completed which measured the in-situ electrical resistivity of 12 different grades of aluminum oxide during HFIR neutron irradiation at 450{degrees}C. No evidence for bulk RIED was observed following irradiation to a maximum dose of 3 dpa with an applied dc electric field of 200 V/mm.

RFID technology for reading of electricity measurements; RFID-lukumoduli saehkoeenergiamittaustietojen luentaan

Energy Technology Data Exchange (ETDEWEB)

Vehvilaeinen, T [MX Electrix Oy, Paelkaene (Finland)

2006-12-19

In the project is developed a reading module for electricity energy meters. The module saves and transmits the meter's energy measurement and power quality data. The project is based on RFID technology, which is a new application in reading of electricity measurements. The reading module of the meter is read via the customers GSM-telephone, which has a RFID- interface. The reading data is transmitted automatically from the module to the GSM hone, when the customer visits the meter. The utility sends the reading request and needed identifier to the customers GSM. After the reading the measured data is transferred to the utility's data base automatically. The utility can send information to the customer of used energy, pricing, make offers etc. The customer can transfer the data to his/hers own computer or get the information via the internet. (orig.)

Moraceae endémicas del Perú

Directory of Open Access Journals (Sweden)

Pamela Cáceres

2013-10-01

Full Text Available La familia Moraceae es reconocida en el Perú por presentar 19 géneros y 128 especies (Brako & Zarucchi, 1993; Ulloa Ulloa et al., 2004, la mayoría arbóreas y/o hemiepífitos. En este trabajo reconocemos dos especies endémicas en igual número de géneros. Las especies endémicas se encuentran en la región Bosques Húmedos Amazónicos, entre los 115 y 220 m de altitud. Ambas especies endémicas se encuentran dentro del Sistema Nacional de Áreas Naturales Protegidas por el Estado.

Rosaceae endémicas del Perú

Directory of Open Access Journals (Sweden)

Wilfredo Mendoza

2013-10-01

Full Text Available La familia Rosaceae es reconocida en el Perú por presentar 24 géneros y 113 especies (Brako & Zarucchi, 1993; Mendoza, 2005; Ulloa Ulloa et al., 2004, entre hierbas, arbustos y árboles. En este trabajo reconocemos 14 especies endémicas en cuatro géneros. Las especies endémicas se encuentran principalmente en las regiones Bosques Pluviales Montanos, Bosques Muy Húmedos Montanos y Páramo, entre los 1900 y 3800 m de altitud. Seis especies endémicas se encuentran representadas dentro del Sistema Nacional de Áreas Naturales Protegidas por el Estado.

Production of a nuclear radiation resistant and mechanically tough electrically insulating material

International Nuclear Information System (INIS)

Brechna, H.

1975-01-01

According to the invention, an electrically insulating material of high mechanical strength and resistance to nuclear radiation may be made of a hardenable plastic material coated on an inorganic supporting tissue. The synthetic resin serving as binder - duroplasts, e.g. epoxide resins, polyester resins or silicon resins - is heated, mixed with a catalyst, a wetting agent and a filler (and, if required, with 0.5-1.5 weight % thixotropic material) and coated, under reduced pressure (o.4 to 0.6 mm Hg), on the supporting tissue whose surface is cleaned before this by heating. It is then hardened. Hardening may also take place directly on the electric conductor to be insulated. One obtains a bubble-free wire coating. The inorganic supporting material is glas fibre tissue, also in combination with mica, while Al 2 O 3 , zirconium, zirconia, magnesium oxide, mica and silica (grain size 10-20 μ). The invention is illustrated by a number of examples. (UWI) [de

Electric field measurements in a dielectric barrier nanosecond pulse discharge with sub-nanosecond time resolution

International Nuclear Information System (INIS)

Goldberg, Benjamin M; Shkurenkov, Ivan; Adamovich, Igor V; Lempert, Walter R; O’Byrne, Sean

2015-01-01

The paper presents the results of time-resolved electric field measurements in a nanosecond discharge between two plane electrodes covered by dielectric plates, using picosecond four-wave mixing diagnostics. For absolute calibration, the IR signal was measured in hydrogen at a pressure of 440 Torr, for electrostatic electric field ranging from 0 to 8 kV cm −1 . The calibration curve (i.e. the square root of IR signal intensity versus electric field) was shown to be linear. By measuring the intensities of the pump, Stokes, and IR signal beam for each laser shot during the time sweep across the high-voltage pulse, temporal evolution of the electric field in the nanosecond pulse discharge was determined with sub-nanosecond time resolution. The results are compared to kinetic modeling predictions, showing good agreement, including non-zero electric field offset before the main high voltage pulse, breakdown moment, and reduction of electric field in the plasma after breakdown. The difference between the experimental results and model predictions is likely due to non-1D structure of the discharge. Comparison with the kinetic modeling predictions shows that electric field in the nanosecond pulse discharge is controlled primarily by electron impact excitation and charge accumulation on the dielectric surfaces. (paper)

Generación y dinámica de electrones runaway en plasmas tokamak

OpenAIRE

Fernández Gómez, Isabel

2016-01-01

La dinámica y generación de electrones runaway en plasmas tokamak constituye el tema central de esta tesis. En un tokamak, el fenómeno runaway es el resultado de la existencia de un campo eléctrico en dirección toroidal. Aquellos electrones cuya velocidad excede un cierto valor crítico se aceleran de forma continua, ya que la e ciencia de las colisiones para disipar la energía ganada en el campo disminuye con la velocidad (∼ ⁻¹) . Se tiene entonces lo que se conoce como un electrón runaway. ...

Nanolithography based contacting method for electrical measurements on single template synthesized nanowires

DEFF Research Database (Denmark)

Fusil, S.; Piraux, L.; Mátéfi-Tempfli, Stefan

2005-01-01

A reliable method enabling electrical measurements on single nanowires prepared by electrodeposition in an alumina template is described. This technique is based on electrically controlled nanoindentation of a thin insulating resist deposited on the top face of the template filled by the nanowires....... We show that this method is very flexible, allowing us to electrically address single nanowires of controlled length down to 100 nm and of desired composition. Using this approach, current densities as large as 10 A cm were successfully injected through a point contact on a single magnetic...

Electrical conductivity measurements in shock compressed liquid nitrogen

International Nuclear Information System (INIS)

Hamilton, D.C.; Mitchell, A.C.; Nellis, W.J.

1985-06-01

The electrical conductivity of shock compressed liquid nitrogen was measured in the pressure range 20 to 50 GPa using a two-stage light-gas gun. The conductivities covered a range 4 x 10 -2 to 1 x 10 2 ohm -1 cm -1 . The data are discussed in terms of a liquid semiconductor model below the onset of the dissociative phase transition at 30 GPa. 15 refs., 1 fig

Highly charged swelling mica reduces Cu bioavailability in Cu-contaminated soils

Energy Technology Data Exchange (ETDEWEB)

Stuckey, Jason W. [Department of Crop and Soil Sciences, Pennsylvania State University, 116 ASI Building, University Park, PA 16802 (United States); Neaman, Alexander [Facultad de Agronomia, P. Universidad Catolica de Valparaiso, Centro Regional de Estudios en Alimentos Saludables (Chile); Ravella, Ramesh; Komarneni, Sridhar [Department of Crop and Soil Sciences, Pennsylvania State University, 116 ASI Building, University Park, PA 16802 (United States); Martinez, Carmen Enid [Department of Crop and Soil Sciences, Pennsylvania State University, 116 ASI Building, University Park, PA 16802 (United States)], E-mail: cem17@psu.edu

2009-01-15

This is the first test of a highly charged swelling mica's (Na-2-mica) ability to reduce the plant-absorbed Cu in Cu-contaminated soils from Chile. Perennial ryegrass (Lolium perenne L.) was grown in two acid soils (Sector 2: pH 4.2, total Cu = 172 mg Cu kg{sup -1} and Sector 3: pH 4.2, total Cu = 112 mg Cu kg{sup -1}) amended with 0.5% and 1% (w/w) mica, and 1% (w/w) montmorillonite. At 10 weeks of growth, both mica treatments decreased the shoot Cu of ryegrass grown in Sector 2 producing shoot Cu concentrations above 21-22 mg Cu kg{sup -1} (the phytotoxicity threshold for that species), yet the mica treatments did not reduce shoot Cu concentrations when grown in Sector 3, which were at a typical level. The mica treatments improved shoot growth in Sector 3 by reducing free and extractable Cu to low enough levels where other nutrients could compete for plant absorption and translocation. In addition, the mica treatments improved root growth in both soils, and the 1% mica treatment reduced root Cu in both soils. This swelling mica warrants further testing of its ability to assist re-vegetation and reduce Cu bioavailability in Cu-contaminated surface soils. - In situ remediation of Cu-contaminated soils with a synthetic mica (Na-2-mica) will aid in re-vegetative efforts.

DNA adsorption and desorption on mica surface studied by atomic force microscopy

Energy Technology Data Exchange (ETDEWEB)

Sun Lanlan [State Key Laboratory of Electroanalytical Chemistry, Changchun Institute of Applied Chemistry, Graduate school of the Chinese Academy of Sciences, Chinese Academy of Sciences, Renmin Street 5625, Changchun 130022 (China); Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16 East Nan-Hu Road, Open Economic Zone, Changchun 130033 (China); Zhao Dongxu [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16 East Nan-Hu Road, Open Economic Zone, Changchun 130033 (China); Zhang Yue; Xu Fugang [State Key Laboratory of Electroanalytical Chemistry, Changchun Institute of Applied Chemistry, Graduate school of the Chinese Academy of Sciences, Chinese Academy of Sciences, Renmin Street 5625, Changchun 130022 (China); Li Zhuang, E-mail: zli@ciac.jl.cn [State Key Laboratory of Electroanalytical Chemistry, Changchun Institute of Applied Chemistry, Graduate school of the Chinese Academy of Sciences, Chinese Academy of Sciences, Renmin Street 5625, Changchun 130022 (China)

2011-05-15

The adsorption of DNA molecules on mica surface and the following desorption of DNA molecules at ethanol-mica interface were studied using atomic force microscopy. By changing DNA concentration, different morphologies on mica surface have been observed. A very uniform and orderly monolayer of DNA molecules was constructed on the mica surface with a DNA concentration of 30 ng/{mu}L. When the samples were immersed into ethanol for about 15 min, various desorption degree of DNA from mica (0-99%) was achieved. It was found that with the increase of DNA concentration, the desorption degree of DNA from the mica at ethanol-mica interface decreased. And when the uniform and orderly DNA monolayers were formed on the mica surface, almost no DNA molecule desorbed from the mica surface in this process. The results indicated that the uniform and orderly DNA monolayer is one of the most stable DNA structures formed on the mica surface. In addition, we have studied the structure change of DNA molecules after desorbed from the mica surface with atomic force microscopy, and found that the desorption might be ascribed to the ethanol-induced DNA condensation.

DNA adsorption and desorption on mica surface studied by atomic force microscopy

International Nuclear Information System (INIS)

Sun Lanlan; Zhao Dongxu; Zhang Yue; Xu Fugang; Li Zhuang

2011-01-01

The adsorption of DNA molecules on mica surface and the following desorption of DNA molecules at ethanol-mica interface were studied using atomic force microscopy. By changing DNA concentration, different morphologies on mica surface have been observed. A very uniform and orderly monolayer of DNA molecules was constructed on the mica surface with a DNA concentration of 30 ng/μL. When the samples were immersed into ethanol for about 15 min, various desorption degree of DNA from mica (0-99%) was achieved. It was found that with the increase of DNA concentration, the desorption degree of DNA from the mica at ethanol-mica interface decreased. And when the uniform and orderly DNA monolayers were formed on the mica surface, almost no DNA molecule desorbed from the mica surface in this process. The results indicated that the uniform and orderly DNA monolayer is one of the most stable DNA structures formed on the mica surface. In addition, we have studied the structure change of DNA molecules after desorbed from the mica surface with atomic force microscopy, and found that the desorption might be ascribed to the ethanol-induced DNA condensation.

La Industria Química: Importancia y Retos

Directory of Open Access Journals (Sweden)

Nancy Montes-Valencia

2015-06-01

Full Text Available La química siempre ha estado presente en la vida del hombre para satisfacer sus necesidades y mejorar su calidad de vida. Hoy en día la industria química es un importante sector industrial presente en la mayoría de países, que dinamiza el crecimiento económico, genera empleo y ofrece diversidad de productos, no obstante produce contaminación al medio ambiente y utiliza recursos naturales no renovables. Por lo tanto surge el concepto de química verde como respuesta a la problemática ambiental cuya estructura es la sostenibilidad, siendo su principal objetivo prevenir la generación de emisiones y armonizar la química con los recursos naturales. Existe un gran reto para la industria química y es encontrar fuentes alternativas de energía para no seguir dependiendo del petróleo, el gas natural y el carbón, una de estas es el uso de la biomasa para la obtención de combustibles líquidos.

Measuring public understanding on Tenaga Nasional Berhad (TNB) electricity bills using ordered probit model

Science.gov (United States)

Zainudin, WNRA; Ramli, NA

2017-09-01

In 2016, Tenaga Nasional Berhad (TNB) had introduced an upgrade in its Billing and Customer Relationship Management (BCRM) as part of its long-term initiative to provide its customers with greater access to billing information. This includes information on real and suggested power consumption by the customers and further details in their billing charges. This information is useful to help TNB customers to gain better understanding on their electricity usage patterns and items involved in their billing charges. Up to date, there are not many studies done to measure public understanding on current electricity bills and whether this understanding could contribute towards positive impacts. The purpose of this paper is to measure public understanding on current TNB electricity bills and whether their satisfaction towards energy-related services, electricity utility services, and their awareness on the amount of electricity consumed by various appliances and equipment in their home could improve this understanding on the electricity bills. Both qualitative and quantitative research methods are used to achieve these objectives. A total of 160 respondents from local universities in Malaysia participated in a survey used to collect relevant information. Using Ordered Probit model, this paper finds respondents that are highly satisfied with the electricity utility services tend to understand their electricity bills better. The electric utility services include management of electricity bills and the information obtained from utility or non-utility supplier to help consumers manage their energy usage or bills. Based on the results, this paper concludes that the probability to understand the components in the monthly electricity bill increases as respondents are more satisfied with their electric utility services and are more capable to value the energy-related services.

CT-scan-monitored electrical resistivity measurements show problems achieving homogeneous saturation

International Nuclear Information System (INIS)

Sprunt, E.S.; Coles, M.E.; Davis, R.M.; Muegge, E.L.; Desai, K.P.

1991-01-01

X-ray CT scans obtained during measurement of the electrical resistivity of core samples revealed some problems in obtaining uniform saturation along the length of the sample. In this paper the electrical resistivity of core samples is measured as a function of water saturation to determine the saturation exponent, which is used in electric log interpretation. An assumption in such tests is that the water saturation is uniformly distributed. Failure of this assumption can result in errors in the determination of the saturation exponent. Three problems were identified in obtaining homogeneous water saturation in two samples of a Middle Eastern carbonate grainstone. A stationary front formed in one sample at 1 psi oil/brine capillary pressure. A moving front formed at oil/brine capillary pressures of 4 psi or less in both samples tested, in both a fresh mixed-wettability state and in a cleaned water-wet state. In these samples, the heterogeneous fluid distribution caused by a rapidly moving front did not dissipate when the capillary pressure was eliminated

A proposed method of measuring the electric-dipole moment of the neutron by ultracold neutron interferometry

International Nuclear Information System (INIS)

Freedman, M.S.; Peshkin, M.; Ringo, G.R.; Dombeck, T.W.

1989-08-01

The use of an ultracold neutron interferometer incorporating an electrostatic accelerator having a strong electric field gradient to accelerate neutrons by their possible electric dipole moment is proposed as a method of measuring the neutron electric dipole moment. The method appears to have the possibility of extending the sensitivity of the measurement by several orders of magnitude, perhaps to 10 -30 e-cm. 9 refs., 3 figs

“Nadie es profeta en su tierra”: Etnografía económica de las dinámicas comerciales de los Kichwa-Otavalo en San Victorino, Bogotá

OpenAIRE

López Ávila, Diego Felipe

2015-01-01

La presente monografía describe las dinámicas económicas de los Kichwas Otavalo en la zona comercial de San Victorino, Bogotá. Dichas dinámicas son examinadas a partir de la Nueva Sociología Económica (Smelser & Swedberg, 2005) y la Etnografía Económica (Dufy & Weber, 2009) para mostrar las divergentes racionalidades que surgen al interior del mercado. Esto nos lleva a debatir con la ciencia económica ortodoxa y los supuestos que manejan frente a la racionalidad, el mercado y la competencia....

Onagraceae endémicas del Perú

Directory of Open Access Journals (Sweden)

Susy Castillo

2013-10-01

Full Text Available Esta es la familia de las «fucsias», la cual es reconocida en el Perú por presentar seis géneros y 76 especies (Brako & Zarucchi, 1993; Ulloa Ulloa et al., 2004, principalmente arbustos y hierbas. En este trabajo reconocemos 24 especies endémicas, la mayoría en el género Fuchsia. Las especies endémicas se encuentran mayormente en la región Bosques Muy Húmedos Montanos, entre los 1600 y 2500 m de altitud. Diez especies endémicas se encuentran representados dentro del Sistema Nacional de Áreas Naturales Protegidas por el Estado.

Measurement and analysis of the electric field radiation in pulsed power system of linear induction accelerator

International Nuclear Information System (INIS)

Cheng Qifeng; Ni Jianping; Meng Cui; Cheng Cheng; Liu Yinong; Li Jin

2009-01-01

The close of high voltage switch in pulsed power system of linear induction accelerator often radiates strong transient electric field, which may influence ambient sensitive electric equipment, signals and performance of other instruments, etc. By performing gridded measurement around the Marx generator, the general distribution law and basic characters of electric field radiation are summarized. The current signal of the discharge circuit is also measured, which demonstrates that the current and the radiated electric field both have a resonance frequency about 150 kHz, and contain much higher frequency components. (authors)

Irreversibility in transformation behavior of equiatomic nickel-titanium alloy by electrical resistivity measurement

International Nuclear Information System (INIS)

Matsumoto, Hitoshi

2004-01-01

Measurements of the electrical resistivity were precisely performed on shape memory Ni 50 Ti 50 alloy in order to reveal the irreversible behavior of the thermoelastic martensitic transformation with thermal cycling. The hump in the electrical resistivity during cooling is enhanced with increasing the number of complete thermal cycles to result in a peak, although no peak in the electrical resistivity is observed on the reverse transformation during heating. The electrical resistivity in the low-temperature phase, of which the temperature dependence is linear, increases with increasing the number of complete thermal cycles. The temperature coefficient of the electrical resistivity in the temperature region of the high-temperature phase increases with elevating the temperature. The transformation is strongly influenced by incomplete thermal cycles to result in a peak in the resistivity even on the reverse transformation after incomplete thermal cycling. It is thought that the anomalous behavior such as enhancement of a resistivity-peak, the increase in the electrical resistivity of the low-temperature phase, and the nonlinear relation between the resistivity and the temperature in the high-temperature phase are attributable to the appearance of an intermediate phase stabilized by transformation-induced defects, the accumulation of the transformation-induced defects, and the electron scattering due to the softening of a phonon mode in the high-temperature phase, respectively. It proved useful to make more accurate measurements of the electrical resistivity in order to investigate the intrinsic behavior of the transformation in NiTi

[Measurement of chemical agents in metallurgy field: electric steel plant].

Science.gov (United States)

Cottica, D; Grignani, E; Ghitti, R; Festa, D; Apostoli, P

2012-01-01

The steel industry maintains its important position in the context of the Italian production involving thousands of workers. The iron and steel processes are divided into primary steel industry, production of intermediate minerals, and secondary steel, scrap from the production of semi-finished industrial and consumer sector (metal inserted into components and metal used for dissipative uses, primarily coatings) and industrial waste. The paper presents the results of environmental monitoring carried out in some electric steel plant for the measurement of airborne chemicals that characterize the occupational exposure of workers employed in particular area like electric oven, to treatment outside the furnace, continuous casting area. For the sampling of the pollutants were used both personal and in fixed positions samplers. The pollutants measured are those typical of steel processes inhalable dust, metals, respirable dust, crystalline silica, but also Polycyclic Aromatic Hydrocarbons (PAH), polychlorinated dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs).

Competitividad Sistémica. Niveles analíticos para el fortalecimiento de sectores de actividad económica

Directory of Open Access Journals (Sweden)

Juliana Ferrer

2005-01-01

Full Text Available Un desarrollo industrial exitoso no se logra meramente considerando la función de producción en el nivel microeconómico, o las condiciones macroeconómicas estables; sino también por la existencia de medidas específicas del gobierno y de organizaciones privadas de desarrollo, orientadas a fortalecer la competitividad de los sectores de actividad económica. Además, la capacidad de vincular las iniciativas, está en función de un conjunto de estructuras político- económicas y de factores socioculturales y patrones básicos de organización, que caracterizan el proceso sistémico de competitividad de cada país. Se concluye que existe una marcada desarticulación entre los niveles de competitividad sistémica; reflejada por una incoherencia entre las políticas de Estado, los requerimientos de sectores de actividad y el reflejo de la necesidad real de las comunidades cada vez más desprovistas de recursos. Se recomienda la necesidad de superar la ardua fase que representa establecer una economía de mercado dirigida a mejorar la condición de vida de la población; por lo que será importante facilitar procesos autónomos de búsqueda y aprendizaje significativos, para el desarrollo de la competitividad de los sectores de actividad económica latinoamericanos.

Capillary condensation of water between mica surfaces above and below zero-effect of surface ions.

Science.gov (United States)

Nowak, Dominika; Christenson, Hugo K

2009-09-01

We have studied the capillary condensation of water from saturated vapor below 0 degrees C in the annular wedge-pore formed around two mica surfaces in contact in a surface force apparatus. The condensed water remains liquid down to at least -9 degrees C, and the measured condensate size is close to the predictions of a recent model for the dependence of the interfacial curvature of supercooled capillary condensates on temperature and surface tension. The small deviation observed may be accounted for by assuming that solute as K(2)CO(3) from the mica-condensate interface dissolves in the condensates and gives rise to an additional depression of the freezing point apart from that caused by the interface curvature. By contrast, measurements of the interface curvature at relative vapor pressures of 0.95-0.99 at 20 degrees C confirm a significantly larger deviation from the Kelvin equation. The magnitude of the deviation is in remarkable agreement with that calculated from the results of an earlier study of capillary condensation of water from a nonpolar liquid, also at T = 20 degrees C. Evidently, additional solute from the surrounding mica surface migrates into the condensates at room temperature. We conclude that the surface diffusion of ions on mica is much slower at subzero temperatures than at room temperature.

A modified Wheeler cap method for radiation efficiency measurement of balanced electrically small antennas

DEFF Research Database (Denmark)

Zhang, Jiaying; Pivnenko, Sergey; Breinbjerg, Olav

2010-01-01

, but not for balanced antennas like loops or dipoles. In this paper, a modified Wheeler cap method is proposed for the radiation efficiency measurement of balanced electrically small antennas and a three-port network model of the Wheeler cap measurement is introduced. The advantage of the modified method...... is that it is wideband, thus does not require any balun, and both the antenna input impedance and radiation efficiency can be obtained. An electrically small loop antenna and a wideband dipole were simulated and measured according to the proposed method and the results of measurements and simulations are presented...

Real-time particle volume fraction measurement in centrifuges by wireless electrical resistance detector

International Nuclear Information System (INIS)

Nagae, Fumiya; Okawa, Kazuya; Matsuno, Shinsuke; Takei, Masahiro; Zhao Tong; Ichijo, Noriaki

2015-01-01

In this study, wireless electrical resistance detector is developed as first step in order to develop electrical resistance tomography (ERT) that are attached wireless communication, and miniaturized. And the particle volume fraction measurement results appropriateness is qualitatively examined. The real-time particle volume fraction measurement is essential for centrifuges, because rotational velocity and supply should be controlled based on the results in order to obtain the effective separation, shorten process time and save energy. However, a technique for the particle volume fraction measurement in centrifuges has not existed yet. In other words, the real-time particle volume fraction measurement in centrifuges becomes innovative technologies. The experiment device reproduces centrifugation in two-phase using particle and salt solution as measuring object. The particle concentration is measured changing rotational velocity, supply and measurement section position. The measured concentration changes coincide with anticipated tendency of concentration changes. Therefore the particle volume fraction measurement results appropriateness are qualitatively indicated. (author)

APRENDIENDO ELECTROQUÍMICA. UN ESTUDIO COMPARATIVO

Directory of Open Access Journals (Sweden)

Maria I. Vera

2011-01-01

Full Text Available Se realizó un seguimiento del proceso de enseñanza y aprendizaje de Electroquímica y se compararon los resultados obtenidos en evaluaciones parciales, con el objetivo de analizar si existen diferencias significativas en la apropiación de contenidos entre alumnos de carreras con diferentes perfiles. Se trabajó en los años 2009 y 2010 con dos grupos de alumnos en cada año, pertenecientes a carreras químicas y no químicas respectivamente. En ambos grupos se desarrollaron, con la misma carga horaria, contenidos conceptuales y procedimentales en clases teóricas con prácticas de resolución de problemas y de laboratorio. Para la evaluación se presentaron idénticas situaciones problemáticas, cuyos resultados muestran diferencias no significativas entre ambos grupos en la identificación del cátodo y del ánodo y cálculo de la fem estándar de la celda; en cambio en la aplicación de la Ecuación de Nernst y la identificación de especies químicas que reaccionan en los electrodos, hay diferencias significativas en las respuestas dadas.

Microcontroller based system for electrical breakdown time delay measurement in gas-filled devices.

Science.gov (United States)

Pejović, Milić M; Denić, Dragan B; Pejović, Momčilo M; Nešić, Nikola T; Vasović, Nikola

2010-10-01

This paper presents realization of a digital embedded system for measuring electrical breakdown time delay. The proposed system consists of three major parts: dc voltage supply, analog subsystem, and a digital subsystem. Any dc power source with the range from 100 to 1000 V can be used in this application. The analog subsystem should provide fast and accurate voltage switching on the testing device as well as transform the signals that represent the voltage pulse on the device and the device breakdown into the form suitable for detection by a digital subsystem. The insulated gate bipolar transistor IRG4PH40KD driven by TC429 MOSFET driver is used for high voltage switching on the device. The aim of a digital subsystem is to detect the signals from the analog subsystem and to measure the elapsed time between their occurrences. Moreover, the digital subsystem controls various parameters that influence time delay and provides fast data storage for a large number of measured data. For this propose, we used the PIC18F4550 microcontroller with a full-speed compatible universal serial bus (USB) engine. Operation of this system is verified on different commercial and custom made gas devices with different structure and breakdown mechanisms. The electrical breakdown time delay measurements have been carried out as a function of several parameters, which dominantly influence electrical breakdown time delay. The obtained results have been verified using statistical methods, and they show good agreement with the theory. The proposed system shows good repeatability, sensitivity, and stability for measuring the electrical breakdown time delay.

Microcontroller based system for electrical breakdown time delay measurement in gas-filled devices

Energy Technology Data Exchange (ETDEWEB)

Pejovic, Milic M.; Denic, Dragan B.; Pejovic, Momcilo M.; Nesic, Nikola T.; Vasovic, Nikola [Faculty of Electronic Engineering, University of Nis, Aleksandra Medvedeva 14, 18000 Nis (Serbia)

2010-10-15

This paper presents realization of a digital embedded system for measuring electrical breakdown time delay. The proposed system consists of three major parts: dc voltage supply, analog subsystem, and a digital subsystem. Any dc power source with the range from 100 to 1000 V can be used in this application. The analog subsystem should provide fast and accurate voltage switching on the testing device as well as transform the signals that represent the voltage pulse on the device and the device breakdown into the form suitable for detection by a digital subsystem. The insulated gate bipolar transistor IRG4PH40KD driven by TC429 MOSFET driver is used for high voltage switching on the device. The aim of a digital subsystem is to detect the signals from the analog subsystem and to measure the elapsed time between their occurrences. Moreover, the digital subsystem controls various parameters that influence time delay and provides fast data storage for a large number of measured data. For this propose, we used the PIC18F4550 microcontroller with a full-speed compatible universal serial bus (USB) engine. Operation of this system is verified on different commercial and custom made gas devices with different structure and breakdown mechanisms. The electrical breakdown time delay measurements have been carried out as a function of several parameters, which dominantly influence electrical breakdown time delay. The obtained results have been verified using statistical methods, and they show good agreement with the theory. The proposed system shows good repeatability, sensitivity, and stability for measuring the electrical breakdown time delay.

Microcontroller based system for electrical breakdown time delay measurement in gas-filled devices

International Nuclear Information System (INIS)

Pejovic, Milic M.; Denic, Dragan B.; Pejovic, Momcilo M.; Nesic, Nikola T.; Vasovic, Nikola

2010-01-01

This paper presents realization of a digital embedded system for measuring electrical breakdown time delay. The proposed system consists of three major parts: dc voltage supply, analog subsystem, and a digital subsystem. Any dc power source with the range from 100 to 1000 V can be used in this application. The analog subsystem should provide fast and accurate voltage switching on the testing device as well as transform the signals that represent the voltage pulse on the device and the device breakdown into the form suitable for detection by a digital subsystem. The insulated gate bipolar transistor IRG4PH40KD driven by TC429 MOSFET driver is used for high voltage switching on the device. The aim of a digital subsystem is to detect the signals from the analog subsystem and to measure the elapsed time between their occurrences. Moreover, the digital subsystem controls various parameters that influence time delay and provides fast data storage for a large number of measured data. For this propose, we used the PIC18F4550 microcontroller with a full-speed compatible universal serial bus (USB) engine. Operation of this system is verified on different commercial and custom made gas devices with different structure and breakdown mechanisms. The electrical breakdown time delay measurements have been carried out as a function of several parameters, which dominantly influence electrical breakdown time delay. The obtained results have been verified using statistical methods, and they show good agreement with the theory. The proposed system shows good repeatability, sensitivity, and stability for measuring the electrical breakdown time delay.

Real time determination of the laser ablated mass by means of electric field-perturbation measurement

Science.gov (United States)

Pacheco, P.; Álvarez, J.; Sarmiento, R.; Bredice, F.; Sánchez-Aké, C.; Villagrán-Muniz, M.; Palleschi, V.

2018-04-01

A Nd:YAG ns-pulsed laser was used to ablate Al, Cd and Zn targets, which were placed between the plates of a planar charged capacitor. The plasma generates a transient redistribution of the electrical charges on the plates that can be measured as a voltage drop across a resistor connected to the ground plate. This signal is proportional to the capacitor applied voltage, the distance between the plates and the total number of ions produced in the ablation process which in turn is related to the laser energy and the ablated mass. After a series of pulses, the targets were weighed on a thermogravimetric balance to measure the ablated mass. Our results show that the electrical signal measured on the resistor is univocally related to the ablated mass from the target. Therefore, after a proper calibration depending on the material and the experimental geometry, the electrical signal can be used for real time quantitative measurement of the ablated mass in pulsed laser generated plasma experiments. The experiments were repeated on an aluminum target, with and without the presence of the external electric field in order to determine the possible influence of the applied electric field on the ablated mass.

High frequency electric field levels: An example of determination of measurement uncertainty for broadband measurements

Directory of Open Access Journals (Sweden)

Vulević Branislav

2016-01-01

Full Text Available Determining high frequency electromagnetic field levels in urban areas represents a very complex task, having in mind the exponential growth of the number of sources embodied in public cellular telephony systems in the past twenty years. The main goal of this paper is a representation of a practical solution in the evaluation of measurement uncertainty for in-situ measurements in the case of spatial averaging. An example of the estimation of the uncertainty for electric field strength broadband measurements in the frequency range from 3 MHz to 18 GHz is presented.

Precise electrical transport measurements by using Bridgman type pressure cell at low temperature

Energy Technology Data Exchange (ETDEWEB)

Oishi, Takayuki [Division of Civil and Enviromental Engineering, Kanazawa University, Kakuma-machi, Kanazawa 920-1192 (Japan); Ohashi, Masashi [Faculty of Environmental Design, Kanazawa University, Kakuma-machi, Kanazawa 920-1192 (Japan)

2010-03-01

We report a technique for the precise measurement of the electrical resisivity under high pressure at low temperature by using Bridgman anvils made of tungsten carbide. Quasi-hydrostatic pressure is generated up to {approx}15 GPa in the relatively large working space which allows the use of large specimens and simple experimental procedures rather than using a standard diamond anvil cell. The application is demonstrated by the measurements of the electrical resistivity of lead in order to describe the effect of pressure on the superconducting transition.

Precise electrical transport measurements by using Bridgman type pressure cell at low temperature

International Nuclear Information System (INIS)

Oishi, Takayuki; Ohashi, Masashi

2010-01-01

We report a technique for the precise measurement of the electrical resisivity under high pressure at low temperature by using Bridgman anvils made of tungsten carbide. Quasi-hydrostatic pressure is generated up to ∼15 GPa in the relatively large working space which allows the use of large specimens and simple experimental procedures rather than using a standard diamond anvil cell. The application is demonstrated by the measurements of the electrical resistivity of lead in order to describe the effect of pressure on the superconducting transition.

High latitude stratospheric electrical measurements in fair and foul weather under various solar conditions

International Nuclear Information System (INIS)

Holzworth, R.H.

1981-01-01

Stratospheric electric field and conductivity measurements during a wide variety of weather and solar conditions are presented. These data are all from high latitude sites in the months of either April or August. The vector electric field is determined by orthogonal double probes connected through high impedance inputs to differential electrometers. The direct conductivity measurement involves determining the relaxation time constant of the medium after refloating a shorted pair of separated probes. Vertical electric field data from several balloon flights with average duration of 18 h at ceiling in fair weather are shown to be well modeled by a simple exponential altitude dependent equation. Examples of solar flare and magnetospheric effects on stratospheric electric fields are shown. Data collected over electrified clouds and thunderstorms are presented along with a discussion of the thunderstorm related electric currents. Lightning stroke signatures in the stratosphere during a large thunderstorm are identified in the electric field data. Current surges through the stratosphere due to DC currents as well as the sferic are calculated. In nearly 1000 h of balloon data no direct solar influence is identified in these data except during major flares. (author)

Preparation of mica/apatite glass-ceramics biomaterials

International Nuclear Information System (INIS)

Liu Yong; Sheng Xiaoxian; Dan Xiaohong; Xiang Qijun

2006-01-01

Glass-ceramics have become more and more important biomaterials. In this work mica glass/apatite composites with various compositions were prepared by casting and subsequent heat treatments. The effects of composition, phase constitution and crystallinity on mechanical properties, including elastic modulus and transverse rupture strength (TRS), were investigated by using X-ray diffraction analyses (XRD), scanning electron microscopy (SEM) and mechanical tests. Results show that addition of apatite composition in mica glass accelerates the crystallization process and induces the formation of fluoroapatite phase, and the nucleation of apatite crystals occurs before that of mica crystals. The fuoroapatite in this work is needle-like, which is almost the same to that in human bone. The transverse rupture strength increases with the content of fluoroapatite and the crystallinity increasing, except that at a low apatite content the mechanical properties are lower than those of mica glass under the same processing conditions. The transverse rupture strength and elastic modulus obtained in this work fall in the range of those of human bone. SBF immersion test demonstrates good bioactivity of this biomaterial

Electric field measurements on plasma bullets in N2 using four-wave mixing

NARCIS (Netherlands)

van der Schans, M.; Böhm, P.; Nijdam, S.; IJzerman, W.L.; Czarnetzki, U.

2015-01-01

Atmospheric pressure plasma jets driven by pulsed DC or kHz AC voltages typically consist of discrete guided ionisation waves called plasma bullets. In this work, the electric field of plasma bullets generated in a pulsed DC jet with N2 as feed gas is investigated. Electric field measurements in N2

Electric field measurements in moving ionization fronts during plasma breakdown

NARCIS (Netherlands)

Wagenaars, E.; Bowden, M.D.; Kroesen, G.M.W.

2006-01-01

We have performed time-resolved, direct measurements of electric field strengths in moving ionization fronts during the breakdown phase of a pulsed plasma. Plasma breakdown, or plasma ignition, is a highly transient process marking the transition from a gas to a plasma. Some aspects of plasma

Design and construction of an instrument for measuring thermistor electrical characteristic

International Nuclear Information System (INIS)

Budiono; Yudi Herdiana

2007-01-01

In this work an instrument for measuring the electrical characteristic of thermistor has been designed and constructed. The instrument was constructed from main components i.e. a micro controller AT89C51, 3 ADC-0804, a LM35 temperature sensor and IC MAX 232. The IC MAX 232 component is used to connect the micro controller to the personal computer serially by using RS-232 standard. While ADC-0804 was used to convert the analog data (DC voltage) to the digital one so that the data was readable by the micro controller. Digital data from 3 ADC-0804 circuit which have been read by the micro controller was sent directly to the personal computer. The data from the measurement which have been stored in the personal computer was then processed to know the value of temperature and measured thermistor resistance. The processed data could be either stored in a data base or displayed in a monitor or printed in the form of table data and in the form a graph of thermistor resistance as the function of temperature. The result of measurement from measuring instrument of the characteristic of thermistor electric's had been made, being compared by measuring calibrated instrument, the deviation is about 0.33 %. (author)

Caracterización estructural y electroquímica de una membrana compuesta de TiO2 y de su soporte poroso basado en arcillas naturales

Directory of Open Access Journals (Sweden)

Rodríguez-Castellón, E.

2004-02-01

Full Text Available The manufacture and characterisation of an inorganic composite membrane (MC consisting of a thin layer of TiO2 (atanase phasedeposited on a porous support (SP obtained from natural clay has been carried out. Chemical and structural characterisations have been mainly made by X ray photoelectron spectroscopy and electronic microphotographs. An electrochemical characterisation of both MC and SP membranes has also been carried out by measuring membrane potential and electrical impedance with the membranes in contact with NaCl solutions at different concentrations. The results allow an estimation of structural parameters for the TiO2 sub-layer and they also show the weak anionic character of this sublayer with a cationic permeselectivity around 10%.Se ha fabricado y caracterizado una membrana inorgánica compuesta (MC consistente en una capa delgada de TiO2 (fase atanasa sobre un soporte poroso (SP obtenido a partir de arcillas naturales. La caracterización química y estructural se ha realizado, principalmente, a partir de los resultados de XPS y de microscopía electrónica de barrido. También se ha realizado una caracterización electroquímica de ambas membranas (MC y SP en contacto con disoluciones de NaCl a distintas concentraciones mediante medidas de espectrocopía de impedancias y potencial de membrana. Los resultados han permitido estimar parámetros geométricos de la capa de TiO2 y poner de manifiesto un carácter débilmente aniónico, con una permeselectividad catiónica del 10%.

Induction Motors by Electric Measurements

Directory of Open Access Journals (Sweden)

Andrzej M. Trzynadlowski

1999-01-01

Full Text Available The paper gives an overview of the issues and means of detection of mechanical abnormalities in induction motors by electric measurements. If undetected and untreated, the worn or damaged bearings, rotor imbalance and eccentricity, broken bars of the rotor cage, and torsional and lateral vibration lead to roughly a half of all failures of induction motor drives. The detection of abnormalities is based on the fact that they cause periodic disturbance of motor variables, such as the speed, torque, current, and magnetic flux. Thus, spectral analysis of those or related quantities may yield a warning about an incipient failure of the drive system. Although the traditional non-invasive diagnostics has mostly been based on the signature analysis of the stator current, other media can also be employed. In particular, the partial instantaneous input power is shown, theoretically and experimentally, to offer distinct advantages under noisy operating conditions. Use of torque and flux estimates is also discussed.

Automatic measurement for monitoring crack growth with electric potential technique

International Nuclear Information System (INIS)

Nakajima, Nobuya; Kikuchi, Masaaki; Shima, Seishi

1981-10-01

In the study of fracture mechanics, it is one of the most important problems to monitor the crack growth phenomena. Recently, many experimental methods have been developed. In this report, the Direct Current (DC) potential method is employed for measuring the crack growth length in the pressuried high temperature water. The objective of the current investigation is to develop an experimental method to quantify the sensitivity of this method in the air environment using the Compact Tension (CT) specimen. The main results obtained are as follows: 1) It is ignored that the electrical potential changes with plastic deformation at the crack tip of the specimen. 2) Using the Reversible Direct Current (RDC) Method, the measurement system gives no effect on the electrical stability for a long time. 3) For the fatigue and statical crack growth length, good relation is observed between the crack length-to-specimen width ratio (a/W) and potential ratio (Va/Vo). (author)

An improved electrical-conductance sensor for void-fraction measurement in a horizontal pipe

International Nuclear Information System (INIS)

Ko, Min Seok; Jemg, Dong Wook; Kim, Sin; Lee, Bo An; Won, Woo Youn; Lee, Yeon Gun

2015-01-01

The electrical-impedance method has been widely used for void-fraction measurement in two-phase flow due to its many favorable features. In the impedance method, the response characteristics of the electrical signal heavily depend upon flow pattern, as well as phasic volume. Thus, information on the flow pattern should be given for reliable void-fraction measurement. This study proposes an improved electrical-conductance sensor composed of a three-electrode set of adjacent and opposite electrodes. In the proposed sensor, conductance readings are directly converted into the flow pattern through a specified criterion and are consecutively used to estimate the corresponding void fraction. Since the flow pattern and the void fraction are evaluated by reading conductance measurements, complexity of data processing can be significantly reduced and real-time information provided. Before actual applications, several numerical calculations are performed to optimize electrode and insulator sizes, and optimal design is verified by static experiments. Finally, the proposed sensor is applied for air-water two-phase flow in a horizontal loop with a 40-mm inner diameter and a 5-m length, and its measurement results are compared with those of a wire-mesh sensor

Trayectorias evolucionistas en la dinámica de la empresa: una aproximación por dinámica de sistemas

Directory of Open Access Journals (Sweden)

Germán Eduardo Vargas

2006-05-01

Full Text Available La actividad de las firmas, como unidad socioeconómica, en el marco evolucionista está orientada integralmente por procesos de identidad, cohesión y mecanismos de adaptación y evolución; en este orden, el presente documento ilustra, a través de un modelo por dinámica de sistemas, cómo la orientación e integración estratégica basada en el conocimiento para la innovación se constituye como un imperativo de desarrollo que, a partir de un pequeño apalancamiento, permite distinguir entre dos trayectorias de evolución, a saber: firmas económicas tradicionales (inerciales, pues introducen mejoras incrementales esporádicas y modernas (dinámicas y radicalmente innovadoras, hecho a partir del cual se obtienen reveladoras conclusiones y desafíos para intervenir y adecuar el comportamiento de las empresas.2

A Step Towards Electric Propulsion Testing Standards: Pressure Measurements and Effective Pumping Speeds

Science.gov (United States)

Dankanich, John W.; Swiatek, Michael W.; Yim, John T.

2012-01-01

The electric propulsion community has been implored to establish and implement a set of universally applicable test standards during the research, development, and qualification of electric propulsion systems. Existing practices are fallible and result in testing variations which leads to suspicious results, large margins in application, or aversion to mission infusion. Performance measurements and life testing under appropriate conditions can be costly and lengthy. Measurement practices must be consistent, accurate, and repeatable. Additionally, the measurements must be universally transportable across facilities throughout the development, qualification, spacecraft integration and on-orbit performance. A preliminary step to progress towards universally applicable testing standards is outlined for facility pressure measurements and effective pumping speed calculations. The standard has been applied to multiple facilities at the NASA Glenn Research Center. Test results and analyses of universality of measurements are presented herein.

Piezo-sensor self-diagnostics using electrical impedance measurements.

Energy Technology Data Exchange (ETDEWEB)

Park, G. H. (Gyu Hae); Farrar, C. R. (Charles R.); Rutherford, A. C. (Amanda C.); Robertson, A. N. (Amy N.)

2004-01-01

This paper present the piezoelectric sensor self-diagnostic procedure that performs in-situ monitoring of the operational status of piezoelectric materials (PZT) used for sensors and actuators in structural health monitoring (SHM) applications. The use of active-sensing piezoelectric materials has received considerable attention in the SHM community. A critical aspect of the piezoelectric active-sensing technologies is that usually large numbers of distributed sensors and actuators are needed to perform the required monitoring process. The sensor/actuator self-diagnostic procedure, where the sensors/actuators are confirmed to be functioning properly during operation, is therefore a critical component to successfully complete the SHM process and to minimize the false indication regarding the structural health. The basis of this procedure is to track the changes in the capacitive value of piezoelectric materials resulting from the sensor failure, which is manifested in the imaginary part of the measured electrical admittances. Furthermore, through the analytical and experimental investigation, it is confirmed that the bonding layer between the PZT and a host structure significantly contributes to the measured capacitive values. Therefore, by monitoring the imaginary part of the admittances, one can quantitatively assess the degradation of the mechanical/electrical properties of the PZT and its attachment to a host structure. This paper concludes with an experimental example to demonstrate the feasibility of the proposed sensor-diagnostic procedure.

Artificially injected charged particles as a tool for the measurement of the electric field in the magnetosphere

International Nuclear Information System (INIS)

Pirre, M.

1982-01-01

Two methods of measuring the parallel electric field in the magnetosphere using artificially injected charged particles are discussed. One method uses electrons to measure the parallel electric field in the vicinity of the spacecraft. It is shown that a very good accuracy can be achieved for such a measurement. The principle of this method is briefly reviewed, the minimum theoretical value measurable by the method is shown, and the limitations on it due to the spacecraft environment are discussed. Most important among the latter is the high level of turbulence about the spacecraft. The second method uses ions to measure the electric potential along the magnetic field lines if the associated parallel electric field is directed downward. For such a field at a lower altitude, Li ions are used to maximize the returning fluxes and to increase the probability of detection. Rockets are more suitable than satellites to make such measurements. 17 references

New method of measuring electric dipole moments in storage rings

NARCIS (Netherlands)

Farley, FJM; Jungmann, K; Miller, JP; Morse, WM; Orlov, YF; Roberts, BL; Semertzidis, YK; Silenko, A; Stephenson, EJ

2004-01-01

A new highly sensitive method of looking for electric dipole moments of charged particles in storage rings is described. The major systematic errors inherent in the method are addressed and ways to minimize them are suggested. It seems possible to measure the muon EDM to levels that test speculative

La fiscalidad indirecta del comercio electrónico online

Directory of Open Access Journals (Sweden)

Eslisabeth Serena Sánchez

2014-06-01

Full Text Available

El comercio electrónico, como manifestación de la sociedad de la información y el conocimiento, ha experimentado un fuerte incremento en los últimos años. Este desarrollo ha puesto de manifiesto la necesidad de adaptar las normas fiscales a las nuevas circunstancias, ya que estas se han mostrado ineficaces para abarcar la nueva realidad. En el presente trabajo se analizan los cambios normativos introducidos para lograr una correcta tributación del comercio electrónico online, lo cual es vital para la mejora de la competitividad económica en el marco de la Unión Europea.

[Machinable property of a novel dental mica glass-ceramic].

Science.gov (United States)

Chen, Ji-hua; Li, Na; Ma, Xin-pei; Zhao, Ying-hua; Sun, Xiang; Li, Guang-xin

2007-12-01

To investigate the machinability of a novel dental mica glass-ceramic and analyze the effect of heat-treatment on its ductile machinable behavior. The drilling and turning experiment were used to measure the machinabilities of the control group (feldspar ceramic: Vita Mark II) and 7 experiment groups treated with different crystallization techniques. The microstructures were analyzed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The average drilling depths in 30 s of the experimental groups ranged from (0.5 +/- 0.1) mm to (7.1 +/- 0.8) mm. There were significant differences between the control [(0.8 +/- 0.1) mm] and the experimental groups (P machining at a high velocity and cut depth. The crystal portion of this group is only about 40%. This material has a satisfactory machinability. The mechanism could be attributed to a combination of the interlocked structure of mica crystals and the low viscosity of glassy phase.

Data-based method for creating electricity use load profiles using large amount of customer-specific hourly measured electricity use data

International Nuclear Information System (INIS)

Raesaenen, Teemu; Voukantsis, Dimitrios; Niska, Harri; Karatzas, Kostas; Kolehmainen, Mikko

2010-01-01

The recent technological developments monitoring the electricity use of small customers provides with a whole new view to develop electricity distribution systems, customer-specific services and to increase energy efficiency. The analysis of customer load profile and load estimation is an important and popular area of electricity distribution technology and management. In this paper, we present an efficient methodology, based on self-organizing maps (SOM) and clustering methods (K-means and hierarchical clustering), capable of handling large amounts of time-series data in the context of electricity load management research. The proposed methodology was applied on a dataset consisting of hourly measured electricity use data, for 3989 small customers located in Northern-Savo, Finland. Information for the hourly electricity use, for a large numbers of small customers, has been made available only recently. Therefore, this paper presents the first results of making use of these data. The individual customers were classified into user groups based on their electricity use profile. On this basis, new, data-based load curves were calculated for each of these user groups. The new user groups as well as the new-estimated load curves were compared with the existing ones, which were calculated by the electricity company, on the basis of a customer classification scheme and their annual demand for electricity. The index of agreement statistics were used to quantify the agreement between the estimated and observed electricity use. The results indicate that there is a clear improvement when using data-based estimations, while the new-estimated load curves can be utilized directly by existing electricity power systems for more accurate load estimates.

Data-based method for creating electricity use load profiles using large amount of customer-specific hourly measured electricity use data

Energy Technology Data Exchange (ETDEWEB)

Raesaenen, Teemu; Niska, Harri; Kolehmainen, Mikko [Department of Environmental Sciences, University of Eastern Finland P.O. Box 1627, FIN-70211 Kuopio (Finland); Voukantsis, Dimitrios; Karatzas, Kostas [Department of Mechanical Engineering, Aristotle University of Thessaloniki, GR-54124 Thessaloniki (Greece)

2010-11-15

The recent technological developments monitoring the electricity use of small customers provides with a whole new view to develop electricity distribution systems, customer-specific services and to increase energy efficiency. The analysis of customer load profile and load estimation is an important and popular area of electricity distribution technology and management. In this paper, we present an efficient methodology, based on self-organizing maps (SOM) and clustering methods (K-means and hierarchical clustering), capable of handling large amounts of time-series data in the context of electricity load management research. The proposed methodology was applied on a dataset consisting of hourly measured electricity use data, for 3989 small customers located in Northern-Savo, Finland. Information for the hourly electricity use, for a large numbers of small customers, has been made available only recently. Therefore, this paper presents the first results of making use of these data. The individual customers were classified into user groups based on their electricity use profile. On this basis, new, data-based load curves were calculated for each of these user groups. The new user groups as well as the new-estimated load curves were compared with the existing ones, which were calculated by the electricity company, on the basis of a customer classification scheme and their annual demand for electricity. The index of agreement statistics were used to quantify the agreement between the estimated and observed electricity use. The results indicate that there is a clear improvement when using data-based estimations, while the new-estimated load curves can be utilized directly by existing electricity power systems for more accurate load estimates. (author)

Measurement of electric field and gradient in the plasma sheath using clusters of floating microspheres

International Nuclear Information System (INIS)

Sheridan, T. E.; Katschke, M. R.; Wells, K. D.

2007-01-01

A method for measuring the time-averaged vertical electric field and its gradient in the plasma sheath using clusters with n=2 or 3 floating microspheres of known mass is described. The particle charge q is found by determining the ratio of the breathing frequency to the center-of-mass frequency for horizontal (in-plane) oscillations. The electric field at the position of the particles is then calculated using the measured charge-to-mass ratio, and the electric-field gradient is determined from the vertical resonance frequency. The Debye length is also found. Experimental results are in agreement with a simple sheath model

Concept, characteristics, and applications of important electrical measuring techniques

International Nuclear Information System (INIS)

Amberg, C.; Czaika, N.; Andreae, G.

1978-01-01

In the field of electrical measuring techniques the investigations were concentrated on the transducers. We investigated the time-temperature behaviour of the following transducers: The weldable, fully encapsulated high temperature strain gauges, inductance and transformer displacement transducers, and weldable capacitive strain transducers with distance sensor. A literatur-review showing the state of techniques reference the influence of nuclear radiation was put together. (orig./HP) [de

Electrical crosstalk-coupling measurement and analysis for digital closed loop fibre optic gyro

International Nuclear Information System (INIS)

Jing, Jin; Hai-Ting, Tian; Xiong, Pan; Ning-Fang, Song

2010-01-01

The phase modulation and the closed-loop controller can generate electrical crosstalk-coupling in digital closed-loop fibre optic gyro. Four electrical cross-coupling paths are verified by the open-loop testing approach. It is found the variation of ramp amplitude will lead to the alternation of gyro bias. The amplitude and the phase parameters of the electrical crosstalk signal are measured by lock-in amplifier, and the variation of gyro bias is confirmed to be caused by the alternation of phase according to the amplitude of the ramp. A digital closed-loop fibre optic gyro electrical crosstalk-coupling model is built by approximating the electrical cross-coupling paths as a proportion and integration segment. The results of simulation and experiment show that the modulation signal electrical crosstalk-coupling can cause the dead zone of the gyro when a small angular velocity is inputted, and it could also lead to a periodic vibration of the bias error of the gyro when a large angular velocity is inputted

Electrical Resistivity Measurement of Petroleum Coke Powder by Means of Four-Probe Method

Science.gov (United States)

Rouget, G.; Majidi, B.; Picard, D.; Gauvin, G.; Ziegler, D.; Mashreghi, J.; Alamdari, H.

2017-10-01

Carbon anodes used in Hall-Héroult electrolysis cells are involved in both electrical and chemical processes of the cell. Electrical resistivity of anodes depends on electrical properties of its constituents, of which carbon coke aggregates are the most prevalent. Electrical resistivity of coke aggregates is usually characterized according to the ISO 10143 standardized test method, which consists of measuring the voltage drop in the bed of particles between two electrically conducing plungers through which the current is also applied. Estimation of the electrical resistivity of coke particles from the resistivity of particle bed is a challenging task and needs consideration of the contribution of the interparticle void fraction and the particle/particle contact resistances. In this work, the bed resistivity was normalized by subtracting the interparticle void fraction. Then, the contact size was obtained from discrete element method simulation and the contact resistance was calculated using Holm's theory. Finally, the resistivity of the coke particles was obtained from the bed resistivity.

La ejecución curricular y la calidad académica de los estudiantes del departamento de electrónica y telecomunicaciones de la Universidad Nacional de Educación Enrique Guzmán y Valle, durante el 2008 y 2009.

OpenAIRE

Soria Cuéllar, Fidel Tadeo

2010-01-01

El objetivo de la presente investigación ha sido la de demostrar la relación significativa entre la ejecución curricular y la calidad académica de los estudiantes de las especialidades de electrónica e informática y Telecomunicaciones e Informática DE LA Universidad Nacional de Educación Enrique Guzmán y Valle (UNE). La Ejecución Curricular está ordenada en tres dimensiones: la enseñanza – aprendizaje (como estrategia, y como desarrollo de las actividades inherentes a este proceso); el desemp...

CARACTERIZACIÓN QUÍMICA Y MINERALÓGICA DE LAS CROMITAS DE LA ZONA DE BELLO Y SAN PEDRO (DEPARTAMENTO DE ANTIOQUIA

Directory of Open Access Journals (Sweden)

Camilo Andres Quintero G.

2010-10-01

Full Text Available Se caracterizaron químicamente cinco muestras de cromita de los municipios de Bello y San Pedro (Antioquia en forma semicuantitativa (Análisis Espectrográfico y cuantitativa (Absorción Atómica y Espectroscopia de Emisión con fuente de plasma de Acoplamiento Inductivo; la caracterización mineralógica de las muestras se realizó mediante DRX, ATG y ATD, Microscopía Óptica y Microscopía Electrónica de Barrido con análisis por microsonda SEM-EDS, Estos resultados muestran la factibilidad de utilizar las cromitas de estos sectores como materia prima refractaria por poseer características químicas similares a las cromitas de Cuba o Filipinas que se explotan en la actualidad.

Major histocompatibility complex class I-related chain A/B (MICA/B) expression in tumor tissue and serum of pancreatic cancer: Role of uric acid accumulation in gemcitabine-induced MICA/B expression

International Nuclear Information System (INIS)

Xu, Xiulong; Rao, Geetha S; Groh, Veronika; Spies, Thomas; Gattuso, Paolo; Kaufman, Howard L; Plate, Janet; Prinz, Richard A

2011-01-01

Major histocompatibility complex class I-related chain A and B (MICA/B) are two stress-inducible ligands that bind the immunoreceptor NKG2D and play an important role in mediating the cyotoxicity of NK and T cells. In this study, we sought to study MICA/B expression in pancreatic cancer and to determine whether and how genotoxic drugs such as gemcitabine can affect MICA/B expression and natural killer cytotoxity. Seven pancreatic cancer cell lines were analyzed for MICA/B expression by flow cytometry and for their sensitivity to NK-92 cell killing by a 51 Cr release assay. MICA/B expression in tumor tissues and sera of pancreatic cancer was analyzed by immunohistochemical staining (IHC) and ELISA, respectively. Two MICA/B-positive cell lines were sensitive to the cytotoxic activity of NK-92 cells. Other two MICA/B-positive cell lines and three MICA/B-negative cell lines were resistant to NK-92 cell killing. MICA/B expression was positive in 17 of 25 (68%) pancreatic ductal adenocarcinomas but not in normal pancreatic ductal epithelial cells. Serum MICA/B levels were significantly elevated in patients with pancreatic adenocarcinomas but did not correlate with the stage of pancreatic cancer and patient survival. Gemcitabine therapy led to increased serum MICA levels in 6 of 10 patients with detectable serum MICA. Allopurinol, an inhibitor of xanthine oxidoreductase that converts xanthine to uric acid, blocked uric acid production, MICA/B expression, and sensitivity to NK-92 cell killing toward a PANC-1 cancer cell line exposed to radiation and two genotoxic drugs, gemcitabine and 5-fluorouracil. The levels of MICA/B expression in serum and tissue of pancreatic cancer are elevated. DNA damage-induced MICA/B expression is mediated through increased uric acid production

Major histocompatibility complex class I-related chain A/B (MICA/B expression in tumor tissue and serum of pancreatic cancer: Role of uric acid accumulation in gemcitabine-induced MICA/B expression

Directory of Open Access Journals (Sweden)

Kaufman Howard L

2011-05-01

Full Text Available Abstract Background Major histocompatibility complex class I-related chain A and B (MICA/B are two stress-inducible ligands that bind the immunoreceptor NKG2D and play an important role in mediating the cyotoxicity of NK and T cells. In this study, we sought to study MICA/B expression in pancreatic cancer and to determine whether and how genotoxic drugs such as gemcitabine can affect MICA/B expression and natural killer cytotoxity. Methods Seven pancreatic cancer cell lines were analyzed for MICA/B expression by flow cytometry and for their sensitivity to NK-92 cell killing by a 51Cr release assay. MICA/B expression in tumor tissues and sera of pancreatic cancer was analyzed by immunohistochemical staining (IHC and ELISA, respectively. Results Two MICA/B-positive cell lines were sensitive to the cytotoxic activity of NK-92 cells. Other two MICA/B-positive cell lines and three MICA/B-negative cell lines were resistant to NK-92 cell killing. MICA/B expression was positive in 17 of 25 (68% pancreatic ductal adenocarcinomas but not in normal pancreatic ductal epithelial cells. Serum MICA/B levels were significantly elevated in patients with pancreatic adenocarcinomas but did not correlate with the stage of pancreatic cancer and patient survival. Gemcitabine therapy led to increased serum MICA levels in 6 of 10 patients with detectable serum MICA. Allopurinol, an inhibitor of xanthine oxidoreductase that converts xanthine to uric acid, blocked uric acid production, MICA/B expression, and sensitivity to NK-92 cell killing toward a PANC-1 cancer cell line exposed to radiation and two genotoxic drugs, gemcitabine and 5-fluorouracil. Conclusions The levels of MICA/B expression in serum and tissue of pancreatic cancer are elevated. DNA damage-induced MICA/B expression is mediated through increased uric acid production.

New equivalent-electrical circuit model and a practical measurement method for human body impedance.

Science.gov (United States)

Chinen, Koyu; Kinjo, Ichiko; Zamami, Aki; Irei, Kotoyo; Nagayama, Kanako

2015-01-01

Human body impedance analysis is an effective tool to extract electrical information from tissues in the human body. This paper presents a new measurement method of impedance using armpit electrode and a new equivalent circuit model for the human body. The lowest impedance was measured by using an LCR meter and six electrodes including armpit electrodes. The electrical equivalent circuit model for the cell consists of resistance R and capacitance C. The R represents electrical resistance of the liquid of the inside and outside of the cell, and the C represents high frequency conductance of the cell membrane. We propose an equivalent circuit model which consists of five parallel high frequency-passing CR circuits. The proposed equivalent circuit represents alpha distribution in the impedance measured at a lower frequency range due to ion current of the outside of the cell, and beta distribution at a high frequency range due to the cell membrane and the liquid inside cell. The calculated values by using the proposed equivalent circuit model were consistent with the measured values for the human body impedance.

Fabrication and electric measurements of nanostructures inside transmission electron microscope.

Science.gov (United States)

Chen, Qing; Peng, Lian-Mao

2011-06-01

Using manipulation holders specially designed for transmission electron microscope (TEM), nanostructures can be characterized, measured, modified and even fabricated in-situ. In-situ TEM techniques not only enable real-time study of structure-property relationships of materials at atomic scale, but also provide the ability to control and manipulate materials and structures at nanoscale. This review highlights in-situ electric measurements and in-situ fabrication and structure modification using manipulation holder inside TEM. Copyright © 2011 Elsevier B.V. All rights reserved.

Algunas reflexiones sobre la distancia entre "hablar química" y "comprender química"

Directory of Open Access Journals (Sweden)

Lydia Raquel Galagovsky

2014-12-01

Full Text Available Una clase de química puede ser considerada como un espacio de comunicación entre el docente experto y los estudiantes novatos, donde los lenguajes utilizados son la interfase explícita y observable del intercambio comunicativo. En el presente trabajo se muestra con dos ejemplos cómo la diversidad de lenguajes químicos en lugar de favorecer la comprensión de los estudiantes, puede actuar como fuente de obstáculos que dificultan la comunicación en el aula. Así mismo, se analizará con otros dos ejemplos cómo el discurso con el que se enseña la disciplina también es potencial generador de errores en los estudiantes, cuando ellos construyen sus modelos mentales idiosincrásicos a partir de un discurso recortado y simplificado, desde las mejores intenciones de realizar buenas transposiciones didácticas. Se plantea que un enfoque de análisis de la situación de aula como un encuentro comunicativo entre experto y novato conduce a una necesaria diferenciación entre "hablar química" y "comprender química".

Preparation and characterization of aluminum based alloy - mica composites

International Nuclear Information System (INIS)

Rashid, M.A.; Shamim, A.

1999-01-01

In this work, six pallets each of 2.0 cm dia and 0.5 cm thickness were prepared by powder metallurgy; half of them also contained 1% mica-powder to form a composite. Inclusion of mica resulted in a decreased density and an increased porosity of the sample. Brinell hardness was found to be 21% less for the composite than for the pure alloy. Micro-graphs of different areas of the sample show uniform distribution of mica particles and avoids around them. (author)

Microstructures and luminescent properties of Ce-doped transparent mica glass-ceramics

International Nuclear Information System (INIS)

Taruta, Seiichi; Iwasaki, Yoshitomo; Nishikiori, Hiromasa; Yamakami, Tomohiko; Yamaguchi, Tomohiro; Kitajima, Kunio; Okada, Kiyoshi

2012-01-01

Highlights: ► Ce-doped transparent glass-ceramics and their parent glasses. ► TEM and STEM images for the microstructures. ► Each mica crystal did not contain Ce uniformly. ► Emission due to Ce 3+ ions in the glass phase and/or Ce 3+ ions in the mica crystals. - Abstract: Transparent mica glass-ceramics were prepared by heating parent glasses that had been doped with 0.5–15 mol% CeO 2 . During the melting and heat treatment, Ce 4+ ions in the specimens were reduced to Ce 3+ ions, and one or both of these ion species were then replaced with Li + ions in the interlayers of the separated mica crystals. However, scanning transmission electron microscope (STEM) and Z-contrast imaging revealed that the mica crystals did not contain the same amount of Ce. On excitation at 254 nm, the parent glasses and glass-ceramics emitted blue light, which originated from the 5d to 4f transition of the Ce 3+ ions. The emission of the glass-ceramic containing a smaller amount of Ce was attributed to the Ce 3+ ions in both the glass phase and the mica crystals, whereas that of the glass-ceramics containing a larger amount of Ce was caused mainly by Ce 3+ ions in the mica crystals. The dependence of the emission band of the parent glasses on the amount of Ce was a unique feature of the Ce-doped transparent mica glass-ceramics and was not observed in previous studies of Eu-doped parent glasses and mica glass-ceramics.

Gentianaceae endémicas del Perú

Directory of Open Access Journals (Sweden)

Susy Castillo

2013-10-01

Full Text Available La familia Gentianaceae es reconocida en el Perú por presentar alrededor de 15 géneros y aproximadamente de 170 especies (Brako & Zarucchi, 1993; Ulloa Ulloa et al., 2004; S. Castillo, com.pers., mayormente hierbas y arbustos. En este trabajo se reconoce 103 especies endémicas en siete géneros. Los géneros con mayor número de especies endemicas son Gentianella y Macrocarpaea. Las especies endémicas ocupan principalmente las regiones de la Puna Húmeda y Seca, Páramo y Bosque Muy Húmedo Montano, entre los 1000 y 5100 m de altitud. Se aplicaron las categorías y criterios de la UICN a 99 especies. Treinta y tres especies endémicas se encuentran representadas dentro de un área protegida.

Self-Diagnosis of Damage in Carbon Fiber Reinforced Composites Using Electrical Residual Resistance Measurement

Energy Technology Data Exchange (ETDEWEB)

Kang, Ji Ho [KAERI, Daejeon (Korea, Republic of)

2009-08-15

The objective of this research was to develop a practical integrated approach using extracted features from electrical resistance measurements and coupled electromechanical models of damage, for in-situ damage detection and sensing in carbon fiber reinforced plastic(CFRP) composites. To achieve this objective, we introduced specific known damage (in terms of type, size, and location) into CFRP laminates and established quantitative relationships with the electrical resistance measurements. For processing of numerous measurement data, an autonomous data acquisition system was devised. We also established a specimen preparation procedure and a method for electrode setup. Coupon and panel CFRP laminate specimens with several known damage were tested. Coupon specimens with various sizes of artificial delaminations obtained by inserting Teflon film were manufactured and the resistance was measured. The measurement results showed that increase of delamination size led to increase of resistance implying that it is possible to sense the existence and size of delamination. A quasi-isotropic panel was manufactured and electrical resistance was measured. Then three different sizes of holes were drilled at a chosen location. The panel was prepared using the established procedures with six electrode connections on each side making a total of twenty-four electrodes. Vertical, horizontal, and diagonal pairs of electrodes were chosen and the resistance was measured. The measurement results showed the possibility of the established measurement system for an in-situ damage detection method for CFRP composite structures.

In situ measurements of contributions to the global electrical circuit by a thunderstorm in southeastern Brazil

Science.gov (United States)

Thomas, J.N.; Holzworth, R.H.; McCarthy, M.P.

2009-01-01

The global electrical circuit, which maintains a potential of about 280??kV between the earth and the ionosphere, is thought to be driven mainly by thunderstorms and lightning. However, very few in situ measurements of electrical current above thunderstorms have been successfully obtained. In this paper, we present dc to very low frequency electric fields and atmospheric conductivity measured in the stratosphere (30-35??km altitude) above an active thunderstorm in southeastern Brazil. From these measurements, we estimate the mean quasi-static conduction current during the storm period to be 2.5 ?? 1.25??A. Additionally, we examine the transient conduction currents following a large positive cloud-to-ground (+ CG) lightning flash and typical - CG flashes. We find that the majority of the total current is attributed to the quasi-static thundercloud charge, rather than lightning, which supports the classical Wilson model for the global electrical circuit.

Química de Heterociclos. Quinolina e isoquinolina

OpenAIRE

Collado, Daniel

2014-01-01

Quinolinas e isoquinolinas: propiedades. Reactividad química: SEAr, SNAr. Reacciones en cadenas laterales. Reacciones de quinolinio e isoquinolinio. Síntesis de quinolinas e isoquinolinas. Otros ciclos. Capítulo sexto de temario de la Asignatura Ampliación de Química Orgánica Avanzada. Quinolina e isoquinolina.

Subcellular Electrical Measurements as a Function of Wood Moisture Content

Science.gov (United States)

Samuel L. Zelinka; José L. Colon Quintana; Samuel V. Glass; Joseph E. Jakes; Alex C. Wiedenhoeft

2015-01-01

The percolation model developed by Zelinka et al. was based upon macroscale measurements of the electrical conductivity and implicitly treats the wood material as homogenous. The transport mechanism proposed by Jakes et al. depends upon a moisture induced glass transition occurring in the hemicelluloses. This theory suggests that there are likely differences in the...

Measurements of fatigue crack length at elevated temperature by D. C. electrical potential method

International Nuclear Information System (INIS)

Matsumoto, Masakatsu; Yamauchi, Isamu; Kodaira, Tsuneo

1982-07-01

The direct current (d.c.) electrical potential method was used to automatically and continuously measure the crack length in cyclic crack growth test at elevated temperature. This report describes some results concerning the calibration curves, i.e. the relation between electrical potential change and amount of crack extention, using SUS 304 and 2 1/4Cr-1Mo steels. It can be concluded that the measurements of fatigue crack length is possible even at elevated temperature as well as at room temperature with the equivalent accuracy. (author)

Measurement strategy for rectangular electrical capacitance tomography sensor

International Nuclear Information System (INIS)

Ye, Jiamin; Ge, Ruihuan; Qiu, Guizhi; Wang, Haigang

2014-01-01

To investigate the influence of the measurement strategy for the rectangular electrical capacitance tomography (ECT) sensor, a Finite Element Method (FEM) is utilized to create the model for simulation. The simulation was carried out using COMSOL Multiphysics(trade mark, serif) and Matlab(trade mark, serif). The length-width ratio of the rectangular sensing area is 5. Twelve electrodes are evenly arranged surrounding the pipe. The covering ratio of the electrodes is 90%. The capacitances between different electrode pairs are calculated for a bar distribution. The air of the relative permittivity 1.0 and the material of the permittivity 3.0 are used for the calibration. The relative permittivity of the second phase is 3.0. The noise free and noise data are used for the image reconstruction using the Linear Back Projection (LBP). The measurement strategies with 1-, 2- and 4- electrode excitation are compared using the correlation coefficient. Preliminary results show that the measurement strategy with 2-electrode excitation outperforms other measurement strategies with 1- or 4-electrode excitation

Electric field measurements in nanosecond pulse discharges in air over liquid water surface

Science.gov (United States)

Simeni Simeni, Marien; Baratte, Edmond; Zhang, Cheng; Frederickson, Kraig; Adamovich, Igor V.

2018-01-01

Electric field in nanosecond pulse discharges in ambient air is measured by picosecond four-wave mixing, with absolute calibration by a known electrostatic field. The measurements are done in two geometries, (a) the discharge between two parallel cylinder electrodes placed inside quartz tubes, and (b) the discharge between a razor edge electrode and distilled water surface. In the first case, breakdown field exceeds DC breakdown threshold by approximately a factor of four, 140 ± 10 kV cm-1. In the second case, electric field is measured for both positive and negative pulse polarities, with pulse durations of ˜10 ns and ˜100 ns, respectively. In the short duration, positive polarity pulse, breakdown occurs at 85 kV cm-1, after which the electric field decreases over several ns due to charge separation in the plasma, with no field reversal detected when the applied voltage is reduced. In a long duration, negative polarity pulse, breakdown occurs at a lower electric field, 30 kV cm-1, after which the field decays over several tens of ns and reverses direction when the applied voltage is reduced at the end of the pulse. For both pulse polarities, electric field after the pulse decays on a microsecond time scale, due to residual surface charge neutralization by transport of opposite polarity charges from the plasma. Measurements 1 mm away from the discharge center plane, ˜100 μm from the water surface, show that during the voltage rise, horizontal field component (Ex ) lags in time behind the vertical component (Ey ). After breakdown, Ey is reduced to near zero and reverses direction. Further away from the water surface (≈0.9 mm), Ex is much higher compared to Ey during the entire voltage pulse. The results provide insight into air plasma kinetics and charge transport processes near plasma-liquid interface, over a wide range of time scales.

What we can learn from measurements of air electric conductivity in 222Rn-rich atmosphere

Science.gov (United States)

Seran, E.; Godefroy, M.; Pili, E.; Michielsen, N.; Bondiguel, S.

2017-02-01

Electric conductivity of air is an important characteristic of the electric properties of an atmosphere. Testing instruments to measure electric conductivity ranging from 10-13 to 10-9 S m-1 in natural conditions found in the Earth atmosphere is not an easy task. One possibility is to use stratospheric balloon flights; another (and a simpler one) is to look for terrestrial environments with significant radioactive decay. In this paper we present measurements carried out with different types of conductivity sensors in two 222Rn-rich environments, i.e., in the Roselend underground tunnel (French Alps) and in the Institute of Radioprotection and Nuclear Safety BACCARA (BAnC de CAllibrage du RAdon) chamber. The concept of the conductivity sensor is based on the classical time relaxation method. New elements in our design include isolation of the sensor sensitive part (electrode) from the external electric field and sensor miniaturization. This greatly extends the application domain of the sensor and permits to measure air electric conductivity when the external electric field is high and varies from few tens of V m-1 to up to few tens of kV m-1. This is suitable to propose the instrument for a planetary mission. Two-fold objectives were attained as the outcome of these tests and their analysis. First was directly related to the performances of the conductivity sensors and the efficiency of the conductivity sensor design to shield the external electric field. Second objective aimed at understanding the decay mechanisms of 222Rn and its progeny in atmosphere and the impact of the enclosed space on the efficiency of gas ionization.

ANALOGIAS EM LIVROS DIDÁTICOS DESTINADOS AO ENSINO SUPERIOR: QUÍMICA ORGÂNICA VERSUS FÍSICO-QUÍMICA

Directory of Open Access Journals (Sweden)

Josué Martins Gonçalves

2016-12-01

Full Text Available Os livros didáticos de Química, via de regra, fazem uso de analogias por se tratar de uma disciplina que envolve inúmeros conceitos abstratos. No entanto, há pouca pesquisa envolvendo identificação e explicação sobre as analogias utilizadas em livros didáticos direcionados ao ensino superior. Nesse sentido, o presente trabalho apresenta um estudo comparativo entre as analogias encontradas em livros de Química Orgânica e Físico-química destinados a estudantes do ensino superior. Foram identificadas 277 analogias nos livros analisados e categorizadas conforme sistemas adaptados de Thiele e Treagust (1994 e Francisco Junior (2009.Uma forma de abordagem mais adequada de utilização das analogias nesses livros foi realizada, bem como a verificação da importância do papel dos professores no uso desse recurso didático. Os resultados indicam que esses livros são ricos em analogias simples, dando ênfase às análogos estruturais no caso de livros de Química Orgânica e análogos funcionais nos de Físico-Química. As analogias simples são mais fáceis de induzirem os alunos a erros conceituais, pois mostram poucas similaridades entre os domínios comparados. É importante ressaltar que nesta pesquisa observa-se uma baixa ocorrência de analogias em que o autor do livro reconhece as limitações e/ou discute estas, repassando toda a responsabilidade ao professor e ao aluno no que se refere à explicação e percepção das analogias, respectivamente. É mister afirmar que muitas das analogias encontradas em alguns capítulos dos livros analisados, poderiam ser suprimidas sem perda significativa da compreensão dos conceitos abordados.

A novel approach to measure the electric dipole moment of the isotope 129-Xe

Directory of Open Access Journals (Sweden)

Kuchler F.

2014-03-01

Full Text Available Permanent electric dipole moments (EDM of fundamental systems are promising systems to find new CP violation beyond the Standard Model. Our EDM experiment is based on hyper-polarized liquid xenon droplets of sub-millimeter size on a micro-fabricated structure, placed in a low-field NMR setup. Implementation of rotating electric fields enables a conceptually new EDM measurement technique, allowing thorough investigation of systematic effects. Still, a Ramsey-type spin precession experiment with static electric field can be realized at similar sensitivity within the same setup. Employing superconducting pick-up coils and highly sensitive LTc-SQUIDs, a large array of independent measurements can be performed simultaneously. With our approach we aim to finally increase the sensitivity on the EDM of 129Xe by more than three orders of magnitude.

A Harmonic Impedance Measurement System for Reduction of Harmonics in the Electricity Grid

NARCIS (Netherlands)

Heskes, P.J.M.; Myrzik, J.M.A.; Kling, W.L.

2009-01-01

This paper describes the development of a Complex Harmonic Impedance Measurement system, called the CHIME-system. This system performs on-line impedance measurements in the electricity grid and will be designed for implementation in Digital Signal Processor (DSP) control systems of grid-connected

A harmonic impedance measurement system for reduction of harmonics in the electricity grid

NARCIS (Netherlands)

Heskes, P.J.M.; Myrzik, J.M.A.; Kling, W.L.

2009-01-01

This paper describes the development of a Complex Harmonic Impedance Measurement system, called the CHIME-system. This system performs on-line impedance measurements in the electricity grid and will be designed for implementation in Digital Signal Processor (DSP) control systems of grid-connected

Análise econômica da geração de energia elétrica a partir do biogás na suinocultura Economic analysis of the generation of electric energy from biogas in pig production

Directory of Open Access Journals (Sweden)

Franco M. Martins

2011-06-01

Full Text Available A demanda por fontes alternativas de energia tem crescido nos últimos anos em função das variações do preço do petróleo aliadas à recente crise energética. Por meio da digestão anaeróbia é possível transformar os dejetos de suínos em biogás. No presente trabalho, estudou-se a viabilidade econômica do uso do biogás como fonte alternativa para a geração de energia elétrica para diferentes períodos de geração. O método utilizado para a avaliação econômica foi o Valor Presente Líquido. O tempo de retorno do capital investido também foi calculado levando em consideração o desconto da taxa de juros nos fluxos de caixa. O estudo demonstrou ser economicamente viável a utilização do biogás da suinocultura, como fonte para geração de energia elétrica. O aumento da demanda de energia elétrica na propriedade aumenta o Valor Presente Líquido e diminui o tempo de retorno do investimento.The demand for alternative sources of energy has grown in recent years in line with the variation of petroleum prices coupled with the recent energy crisis. Through anaerobic digestion swine manure can be converted into biogas. In the present study it was evaluated the economic viability of using biogas as an alternative source for the production of electricity, for different periods of generation. The method used for the economic evaluation was the Net Present Value (NPV. The time of return on invested capital was also calculated taking into account the discount interest rate on cash flows. The study proved to be economically viable use of biogas from swine manure as a source for generating electricity. The increased demand for electricity in the property increases the Net Present Value and decreases the time required for return of the investment.

CONFLICTO, VIOLENCIA SOCIOECONÓMICA Y DESPLAZAMIENTO FORZADO EN COLOMBIA

Directory of Open Access Journals (Sweden)

Andrés Felipe Mora Cortés

2013-12-01

Full Text Available Este artículo introduce el concepto de violencia socioeconómica, que se refiere a mecanismos de regulación de conflictos distributivos y prácticas gubernamentales que eliminan las condiciones base para la reproducción de la vida. Se identifican tres expresiones clave de la violencia socioeconómica: el despojo, la inseguridad económica y la no generación de oportunidades. El artículo insiste en el efecto desproporcionado que dichas expresiones de violencia socioeconómica tienen sobre la población desplazada; también defiende la necesidad de una agenda mínima que erradique la violencia como lógica reguladora de los conflictos distributivos y que sirva de base para la construcción de paz con justicia social en Colombia.

Research on motor rotational speed measurement in regenerative braking system of electric vehicle

Science.gov (United States)

Pan, Chaofeng; Chen, Liao; Chen, Long; Jiang, Haobin; Li, Zhongxing; Wang, Shaohua

2016-01-01

Rotational speed signals acquisition and processing techniques are widely used in rotational machinery. In order to realized precise and real-time control of motor drive and regenerative braking process, rotational speed measurement techniques are needed in electric vehicles. Obtaining accurate motor rotational speed signal will contribute to the regenerative braking force control steadily and realized higher energy recovery rate. This paper aims to develop a method that provides instantaneous speed information in the form of motor rotation. It addresses principles of motor rotational speed measurement in the regenerative braking systems of electric vehicle firstly. The paper then presents ideal and actual Hall position sensor signals characteristics, the relation between the motor rotational speed and the Hall position sensor signals is revealed. Finally, Hall position sensor signals conditioning and processing circuit and program for motor rotational speed measurement have been carried out based on measurement error analysis.

Effects of contact resistance on electrical conductivity measurements of SiC-based materials

Energy Technology Data Exchange (ETDEWEB)

Youngblood, G.E.; Thomsen, E.C.; Henager, C.H., E-mail: chuck.henager@pnnl.gov

2013-11-15

A combination 2/4-probe method was used to measure electrical resistances across a pure, monolithic CVD-SiC disc sample with contact resistance at the SiC/metallic electrode interfaces. By comparison of the almost simultaneous 2/4-probe measurements, the specific contact resistance (R{sub c}) and its temperature dependence were determined for two types (sputtered gold and porous nickel) electrodes from room temperature (RT) to ∼973 K. The R{sub c}-values behaved similarly for each type of metallic electrode: R{sub c} > ∼1000 Ω cm{sup 2} at RT, decreasing continuously to ∼1–10 Ω cm{sup 2} at 973 K. The temperature dependence of the inverse R{sub c} indicated thermally activated electrical conduction across the SiC/metallic interface with an apparent activation energy of ∼0.3 eV. For the flow channel insert application in a fusion reactor blanket, contact resistance potentially could reduce the transverse electrical conductivity by about 50%.

Evaluation of electrical impedance ratio measurements in accuracy of electronic apex locators.

Science.gov (United States)

Kim, Pil-Jong; Kim, Hong-Gee; Cho, Byeong-Hoon

2015-05-01

The aim of this paper was evaluating the ratios of electrical impedance measurements reported in previous studies through a correlation analysis in order to explicit it as the contributing factor to the accuracy of electronic apex locator (EAL). The literature regarding electrical property measurements of EALs was screened using Medline and Embase. All data acquired were plotted to identify correlations between impedance and log-scaled frequency. The accuracy of the impedance ratio method used to detect the apical constriction (APC) in most EALs was evaluated using linear ramp function fitting. Changes of impedance ratios for various frequencies were evaluated for a variety of file positions. Among the ten papers selected in the search process, the first-order equations between log-scaled frequency and impedance were in the negative direction. When the model for the ratios was assumed to be a linear ramp function, the ratio values decreased if the file went deeper and the average ratio values of the left and right horizontal zones were significantly different in 8 out of 9 studies. The APC was located within the interval of linear relation between the left and right horizontal zones of the linear ramp model. Using the ratio method, the APC was located within a linear interval. Therefore, using the impedance ratio between electrical impedance measurements at different frequencies was a robust method for detection of the APC.

Research of Electrical Conductivity Measurement System for Mine Bursting Water Based on Dual Frequency Method

Directory of Open Access Journals (Sweden)

Zhou Mengran

2016-01-01

Full Text Available This paper presents a double frequency conductivity measurement method for measuring mine bursting water, to solve the capacitance effect of the conductivity sensor itself has the help. The core controller of the system is the single chip microcomputer ATMEGA128. This paper introduces the basic principle of the measurement of the existing problems and the dual frequency measurement method, and then introduces and analyzes the hardware. To test and analyze the collected data, the double frequency method is found to have good stability and accuracy in the measurement of the electrical conductivity of mine inrush water. It is proved that the method and the system design of the hardware circuit can accurately measure the electric conductivity of the mine inrush water source.

Measurements and simulations for peak electrical load reduction in cooling dominated climate

International Nuclear Information System (INIS)

Sadineni, Suresh B.; Boehm, Robert F.

2012-01-01

Peak electric demand due to cooling load in the Desert Southwest region of the US has been an issue for the electrical energy suppliers. To address this issue, a consortium has been formed between the University of Nevada Las Vegas, Pulte Homes (home builder) and NV Energy (local utility) in order to reduce the peak load by more than 65%. The implemented strategies that were used to accomplish that goal consist of energy efficiency in homes, onsite electricity generation through roof integrated PV, direct load control, and battery storage at the substation level. The simulation models developed using building energy analysis software were validated against measured data. The electrical energy demand for the upgraded home during peak period (1:00–7:00 PM) decreased by approximately 37% and 9% compared to a code standard home of the same size, due to energy efficiency and PV generation, respectively. The total decrease in electrical demand due to energy efficiency and PV generation during the peak period is 46%. Additionally, a 2.2 °C increase in thermostat temperature from 23.9 °C to 26.1 °C between 4:00 PM and 7:00 PM has further decreased the average demand during the peak period by 69% of demand from a standard home. -- Highlights: ► A study to demonstrate peak load reductions of 65% at the substation. ► A new residential energy efficient community named Villa Trieste is being developed. ► The peak demand from the homes has decreased by 37% through energy efficiency. ► A 1.8 kWp system along with energy efficiency measures decreased peak by 46%.

Electric field measurements in near-atmospheric pressure nitrogen and air based on a four-wave mixing scheme

International Nuclear Information System (INIS)

Mueller, Sarah; Luggenhoelscher, Dirk; Czarnetzki, Uwe; Ito, Tsuyohito; Kobayashi, Kazunobu; Hamaguchi, Satoshi

2010-01-01

Electric fields are measured for the first time in molecular nitrogen at atmospheric pressures. Measurements are performed in either pure nitrogen or air. The laser spectroscopic technique applied here is based on a CARS-like four-wave mixing scheme originally developed for measurements in molecular hydrogen by Ochkin and Tskhai in 1995. The technique is ideal for investigation of microdischarges at atmospheric pressures. The frequencies of two focussed laser beams in the visible are tuned to match the energy difference between the two lowest vibrational levels in nitrogen. The presence of a static electric field then leads to the emission of coherent IR radiation at this difference frequency. The signal intensity scales with the square of the static electric field strength. Parallel to this process also anti-Stokes radiation by the standard CARS process is generated. Normalization of the IR signal by the CARS signal provides a population independent measurement quantity. Experimental results at various pressures and electric field strengths are presented.

Results of acoustic measurements with an electric boiling generator at KNK II

International Nuclear Information System (INIS)

Aberle, J.

1987-08-01

With regard to an integral core surveillance in sodium-cooled breeder reactors acoustic measurement techniques are under development. To determine experimentally the acoustic transfer function of a reactor core and to demonstrate the detectability of local sodium boiling, experiments with a so-called Boiling Generator were carried out in the KNK II reactor. The main part of this Boiling Generator was an electrically heated pin bundle which was equipped with a local blockage to obtain cooling disturbances. In this report the results of the acoustic measurements carried out with the Boiling Generator are presented. Main topic of the evaluation is the determination of the acoustic transfer function between the core and the upper sodium plenum. The signal conditioning necessary prior to this investigation is also explained. Great effort was required to suppress electrical disturbances which superimposed the acoustic signals and could not be eliminated by the hardware during the experiments. Finally, the detectability of local boiling using acoustic measurements is considered

Control of systematic uncertainties in the storage ring search for an electric dipole moment by measuring the electric quadrupole moment

Directory of Open Access Journals (Sweden)

Andrzej Magiera

2017-09-01

Full Text Available Measurements of electric dipole moment (EDM for light hadrons with use of a storage ring have been proposed. The expected effect is very small, therefore various subtle effects need to be considered. In particular, interaction of particle’s magnetic dipole moment and electric quadrupole moment with electromagnetic field gradients can produce an effect of a similar order of magnitude as that expected for EDM. This paper describes a very promising method employing an rf Wien filter, allowing to disentangle that contribution from the genuine EDM effect. It is shown that both these effects could be separated by the proper setting of the rf Wien filter frequency and phase. In the EDM measurement the magnitude of systematic uncertainties plays a key role and they should be under strict control. It is shown that particles’ interaction with field gradients offers also the possibility to estimate global systematic uncertainties with the precision necessary for an EDM measurement with the planned accuracy.

Control of systematic uncertainties in the storage ring search for an electric dipole moment by measuring the electric quadrupole moment

Science.gov (United States)

Magiera, Andrzej

2017-09-01

Measurements of electric dipole moment (EDM) for light hadrons with use of a storage ring have been proposed. The expected effect is very small, therefore various subtle effects need to be considered. In particular, interaction of particle's magnetic dipole moment and electric quadrupole moment with electromagnetic field gradients can produce an effect of a similar order of magnitude as that expected for EDM. This paper describes a very promising method employing an rf Wien filter, allowing to disentangle that contribution from the genuine EDM effect. It is shown that both these effects could be separated by the proper setting of the rf Wien filter frequency and phase. In the EDM measurement the magnitude of systematic uncertainties plays a key role and they should be under strict control. It is shown that particles' interaction with field gradients offers also the possibility to estimate global systematic uncertainties with the precision necessary for an EDM measurement with the planned accuracy.

A new contact electric resistance technique for in-situ measurement of the electric resistance of surface films on metals in electrolytes at high temperatures and pressures

International Nuclear Information System (INIS)

Saario, T.; Marichev, V.A.

1993-01-01

Surface films play a major role in corrosion assisted cracking. A new Contact Electric Resistance (CER) method has been recently developed for in situ measurement of the electric resistance of surface films. The method has been upgraded for high temperature high pressure application. The technique can be used for any electrically conductive material in any environment including liquid, gas or vacuum. The technique has been used to determine in situ the electric resistance of films on metals during adsorption of water and anions, formation and destruction of oxides and hydrides, electroplating of metals and to study the electric resistance of films on semiconductors. The resolution of the CER technique is 10 -9 Ω, which corresponds to about 0.03 monolayers of deposited copper during electrochemical deposition Cu/Cu 2+ . Electric resistance data can be measured with a frequency of the order of one hertz, which enables one to follow in situ the kinetics of surface film related processes. The kinetics of these processes and their dependence on the environment, temperature, pH and electrochemical potential can be investigated

Moessbauer spectra of white micas from the Central Western Carpathians Mountains

International Nuclear Information System (INIS)

Sitek, J; Toth, I; Sulak, M; Putis, M

2010-01-01

Potassium white micas from the rocks included into Cretaceous deformation zones (ca. 100-70 Ma in age) of the Central Western Carpathians were investigated by Moessbauer spectroscopy. White micas formed during a polystage evolution and changing P-T conditions of their crystallization in crustal-scale shear zones. We found criteria for distinguishing generations of celadonite-poor (muscovitic) and celadonite-rich (phengitic) white micas using Moessbauer spectroscopy. This method revealed contrasting spectra characterized by typical quadrupole doublets corresponding to Fe 2+ Fe 3+ contents in white micas. They are in the range of 2.9-3.0 mm/s for phengite, and 2.6-2.7 mm/s for muscovite. Moessbauer spectra reflect well the chemical changes in white mica aggregates, especially of those close to the end-member muscovite and (alumino-)celadonite compositions.

Moessbauer spectra of white micas from the Central Western Carpathians Mountains

Energy Technology Data Exchange (ETDEWEB)

Sitek, J; Toth, I [Department of Nuclear Physics and Technology, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Ilkovicova 3, Bratislava (Slovakia); Sulak, M; Putis, M, E-mail: jozef.sitek@stuba.s [Department of of Mineralogy and Petrology, Faculty of Natural Sciences, Comenius University Bratislava, Mlynska dolina G, 842 15 Bratislava (Slovakia)

2010-03-01

Potassium white micas from the rocks included into Cretaceous deformation zones (ca. 100-70 Ma in age) of the Central Western Carpathians were investigated by Moessbauer spectroscopy. White micas formed during a polystage evolution and changing P-T conditions of their crystallization in crustal-scale shear zones. We found criteria for distinguishing generations of celadonite-poor (muscovitic) and celadonite-rich (phengitic) white micas using Moessbauer spectroscopy. This method revealed contrasting spectra characterized by typical quadrupole doublets corresponding to Fe{sup 2+} Fe{sup 3+} contents in white micas. They are in the range of 2.9-3.0 mm/s for phengite, and 2.6-2.7 mm/s for muscovite. Moessbauer spectra reflect well the chemical changes in white mica aggregates, especially of those close to the end-member muscovite and (alumino-)celadonite compositions.

Measurement of ac electrical conductivity of molten glass by impedance measurement using co-axial cylinder electrode

International Nuclear Information System (INIS)

Shah, J.G.; Yalmali, V.S.; Tawde, Manisha; Mishra, R.

2006-01-01

The need of nuclear power as an energy source requires the solution of many problems. One of the most important is fixation of high level radioactive waste (HLW) in suitable borosilicate glass formulation. The major issue with this process is maximum waste loading in the final vitrified product without compromising on long term product characteristics. The electrical resistivity measurement at high temperature could not be measured with good precision using standard parallel plate electrode configuration due to error in cell constant measurement. Hence a high accuracy, calibration free technique consisting of co-axial electrodes was employed

Prognostic value of MICA/B in cancers: a systematic review and meta-analysis.

Science.gov (United States)

Zhao, Yijing; Chen, Naifei; Yu, Yu; Zhou, Lili; Niu, Chao; Liu, Yudi; Tian, Huimin; Lv, Zheng; Han, Fujun; Cui, Jiuwei

2017-11-10

MHC class I chain related-proteins A (MICA) and B (MICB) are natural killer group 2D ligands that mediate tumor surveillance. Several studies have suggested that MICA/B levels predict clinical outcomes in patients with cancer; however, this remains contentious. Here, we present a systematic review and meta-analysis of available studies of the prognostic value of MICA/B in cancer. We searched PubMed, Embase, Clinicaltrials.gov, and Cochrane Library to identify studies published from inception to July 2017 that assessed MICA/B in patients with cancer. The hazard ratio (HR) and 95% confidence interval (CI) of MICA/B were extracted for overall survival (OS) analysis. A total of 19 studies comprising 2,588 patients with 10 different types of cancer were included in the study. Low sMICA/B levels were found associated with significantly longer OS (HR = 1.65, 95% CI [1.42-1.92], P < 0.00001). Patients with cancers of digestive system that exhibited high MICA/B expression had significantly longer OS in (HR = 0.56, 95% CI [0.39-0.80], P = 0.002) compared with those with lower MICA/B expression ( I 2 = 35%, P = 0.18). Serum soluble MICA/B represents a potential prognostic marker in various human cancers. High cell-surface MICA/B expression in cancers of the digestive system was found associated with increased survival.

Measurement of electroosmotic and electrophoretic velocities using pulsed and sinusoidal electric fields.

Science.gov (United States)

Sadek, Samir H; Pimenta, Francisco; Pinho, Fernando T; Alves, Manuel A

2017-04-01

In this work, we explore two methods to simultaneously measure the electroosmotic mobility in microchannels and the electrophoretic mobility of micron-sized tracer particles. The first method is based on imposing a pulsed electric field, which allows to isolate electrophoresis and electroosmosis at the startup and shutdown of the pulse, respectively. In the second method, a sinusoidal electric field is generated and the mobilities are found by minimizing the difference between the measured velocity of tracer particles and the velocity computed from an analytical expression. Both methods produced consistent results using polydimethylsiloxane microchannels and polystyrene micro-particles, provided that the temporal resolution of the particle tracking velocimetry technique used to compute the velocity of the tracer particles is fast enough to resolve the diffusion time-scale based on the characteristic channel length scale. Additionally, we present results with the pulse method for viscoelastic fluids, which show a more complex transient response with significant velocity overshoots and undershoots after the start and the end of the applied electric pulse, respectively. © 2016 The Authors. Electrophoresis published by Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

A novel approach to measure the electric dipole moment of 129Xenon

Energy Technology Data Exchange (ETDEWEB)

Kuchler, Florian; Feldmeier, Wolfhardt; Fierlinger, Peter; Taubenheim, Bernd [Excellence Cluster Universe, Technische Universitaet Muenchen, Garching (Germany)

2012-07-01

Permanent electric dipole moments (EDM) are promising systems to find new CP violation. The properties of the diamagnetic atom 129-Xe make it a particularly interesting candidate for an EDM search, as it enables new experimental strategies. Although the current experimental limit of d{sub Xe} < 4.0.10{sup -27} ecm is many orders of magnitude higher than the Standard Model (SM) prediction, theories beyond the SM usually require larger EDMs. Our experiment is based on microscopic hyper-polarized liquid xenon droplets, placed in a low-field NMR setup. Implementation of rotating electric fields enables a conceptually new EDM measurement technique, allowing thorough investigation of systematic effects. Still, a Ramsey-type spin precession experiment with static electric field can be realized at similar sensitivity within the same setup. Employing superconducting pick-up coils and highly sensitive LTc-SQUIDs, a large array of independent measurements can be performed simultaneously with different field configurations. With our novel approach we aim to be sensitive to an EDM of 129-Xe on the order of 10{sup -30} ecm. The talk gives an update on the current status of the xenon EDM experiment.

In situ electrical conductivity measurements of H{sub 2}O under static pressure up to 28 GPa

Energy Technology Data Exchange (ETDEWEB)

Liu, Bao, E-mail: liubao@nedu.edu.cn [Institute of Materials Physics, College of Science, Northeast Dianli University, Jilin 132012 (China); State Key Laboratory of Superhard Materials, Institute of Atomic and Molecular Physics, Jilin University, Changchun 130012 (China); Gao, Yang [State Key Laboratory of Superhard Materials, Institute of Atomic and Molecular Physics, Jilin University, Changchun 130012 (China); Department of Mechanical Engineering, Texas Tech University, Lubbock, TX 79409 (United States); Han, Yonghao [State Key Laboratory of Superhard Materials, Institute of Atomic and Molecular Physics, Jilin University, Changchun 130012 (China); Ma, Yanzhang [Department of Mechanical Engineering, Texas Tech University, Lubbock, TX 79409 (United States); Gao, Chunxiao, E-mail: cc060109@qq.com [State Key Laboratory of Superhard Materials, Institute of Atomic and Molecular Physics, Jilin University, Changchun 130012 (China)

2016-08-26

Highlights: • We conduct in situ electrical conductivity measurements on water in a diamond anvil cell (DAC) under high pressure up to 28 GPa and study the electrical transport properties of water and ices. • In liquid state, the increasing rate of electrical conductivity with pressure is slower than that obtained in shock-waves measurements. • In solid phase, the relationship between electrical conductivity and pressure is discontinuous, which is corresponding to phase transformation from ice VIII to ice VII. • The difference in electrical conductivity of VI, VII, and VIII may associate with different orientational ordering in these ices. • The electrical conduction in these ices is dominated by already existing ions and Bjerrum defects, which play an important role in electrical transport properties of ices. - Abstract: The in situ electrical conductivity measurements on water in both solid state and liquid state were performed under pressure up to 28 GPa and temperature from 77 K to 300 K using a microcircuit fabricated on a diamond anvil cell (DAC). Water chemically ionization mainly contributes to electrical conduction in liquid state, which is in accord with the results obtained under dynamic pressure. Energy band theory of liquid water was used to understand effect of static pressure on electrical conduction of water. The electric conductivity of H{sub 2}O decreased discontinuously by four orders of magnitude at 0.7–0.96 GPa, indicating water frozen at this P–T condition. Correspondingly, the conduction of H{sub 2}O in solid state is determined by arrangement and bending of H-bond in ice VI and ice VII. Based on Jaccard theory, we have concluded that the charge carriers of ice are already existing ions and Bjerrum defects.

First Measurement of the Atomic Electric Dipole Moment of (225)Ra.

Science.gov (United States)

Parker, R H; Dietrich, M R; Kalita, M R; Lemke, N D; Bailey, K G; Bishof, M; Greene, J P; Holt, R J; Korsch, W; Lu, Z-T; Mueller, P; O'Connor, T P; Singh, J T

2015-06-12

The radioactive radium-225 ((225)Ra) atom is a favorable case to search for a permanent electric dipole moment. Because of its strong nuclear octupole deformation and large atomic mass, (225)Ra is particularly sensitive to interactions in the nuclear medium that violate both time-reversal symmetry and parity. We have developed a cold-atom technique to study the spin precession of (225)Ra atoms held in an optical dipole trap, and demonstrated the principle of this method by completing the first measurement of its atomic electric dipole moment, reaching an upper limit of |d((225)Ra)|<5.0×10(-22)  e cm (95% confidence).

Phyllitic minerals in hydrothermal uranium deposits. I. Crystalchemistry of relict and newly formed micas

International Nuclear Information System (INIS)

Leroy, Jacques; Cathelineau, Michel

1982-01-01

Several generations of white micas have been recognised in four two mica granite massifs which are associated with uranium deposits in the Hercynian chain. These different generations correspond to distinct geological phenomena belonging to the deuteric and hydrothermal stages of the history of these massifs. Crystalchemical studies of these micas with the aid of the electronic microprobe show that each of these phenomena corresponds a phengite of different, well defined compositions. An increase in the phengitic character and a decrease in the paragonite component are observed over time. Strong similarities exist between micas of the same generation belonging to different granite massifs. The study of the evolution of the earliest deuteric micas during later hydrothermal phenomena, mica episyenitisation and deposition of pitchblende, has shown two opposed trends. In the case of mica episyenitisation, the micas tend to reequilibrate, while in the case of pitchblende deposition and the vein stage in general, the micas preserve their primary character [fr

Measurements of intermediate-frequency electric and magnetic fields in households

Energy Technology Data Exchange (ETDEWEB)

Aerts, Sam, E-mail: sam.aerts@intec.ugent.be [Department of Information Technology, Ghent University/iMinds, iGent, Technologiepark-Zwijnaarde 15, B-9052 Ghent (Belgium); Calderon, Carolina [Centre for Radiation, Chemical and Environmental Hazards, Public Health England, Chilton, Didcot, Oxon OX11 0RQ (United Kingdom); Valič, Blaž [Institute of Non-Ionizing Radiation (INIS), Pohorskega bataljona 215, Ljubljana 1000 (Slovenia); Maslanyj, Myron; Addison, Darren; Mee, Terry; Goiceanu, Cristian [Centre for Radiation, Chemical and Environmental Hazards, Public Health England, Chilton, Didcot, Oxon OX11 0RQ (United Kingdom); Verloock, Leen; Van den Bossche, Matthias [Department of Information Technology, Ghent University/iMinds, iGent, Technologiepark-Zwijnaarde 15, B-9052 Ghent (Belgium); Gajšek, Peter [Institute of Non-Ionizing Radiation (INIS), Pohorskega bataljona 215, Ljubljana 1000 (Slovenia); Vermeulen, Roel [Institute for Risk Assessment Sciences, Department of Environmental Epidemiology, Utrecht University, Yalelaan 2, 3508 Utrecht (Netherlands); Röösli, Martin [Swiss Tropical and Public Health Institute (Swiss TPH), Socinstrasse 57, P.O. Box, 4002 Basel (Switzerland); University of Basel, Petersplatz 1, 4003 Basel (Switzerland); Cardis, Elisabeth [Barcelona Institute for Global Health (ISGlobal) and Municipal Institute of Medical Research (IMIM-Hospital del Mar), Doctor Aiguader, 88, 08003 Barcelona (Spain); Martens, Luc; Joseph, Wout [Department of Information Technology, Ghent University/iMinds, iGent, Technologiepark-Zwijnaarde 15, B-9052 Ghent (Belgium)

2017-04-15

Historically, assessment of human exposure to electric and magnetic fields has focused on the extremely-low-frequency (ELF) and radiofrequency (RF) ranges. However, research on the typically emitted fields in the intermediate-frequency (IF) range (300 Hz to 1 MHz) as well as potential effects of IF fields on the human body remains limited, although the range of household appliances with electrical components working in the IF range has grown significantly (e.g., induction cookers and compact fluorescent lighting). In this study, an extensive measurement survey was performed on the levels of electric and magnetic fields in the IF range typically present in residences as well as emitted by a wide range of household appliances under real-life circumstances. Using spot measurements, residential IF field levels were found to be generally low, while the use of certain appliances at close distance (20 cm) may result in a relatively high exposure. Overall, appliance emissions contained either harmonic signals, with fundamental frequencies between 6 kHz and 300 kHz, which were sometimes accompanied by regions in the IF spectrum of rather noisy, elevated field strengths, or much more capricious spectra, dominated by 50 Hz harmonics emanating far in the IF domain. The maximum peak field strengths recorded at 20 cm were 41.5 V/m and 2.7 A/m, both from induction cookers. Finally, none of the appliance emissions in the IF range exceeded the exposure summation rules recommended by the International Commission on Non-Ionizing Radiation Protection guidelines and the International Electrotechnical Commission (IEC 62233) standard at 20 cm and beyond (maximum exposure quotients EQ{sub E} 1.0 and {sub E}Q{sub H} 0.13). - Highlights: • Survey of residential electric and magnetic fields at intermediate frequencies (IF). • IF-EF and -MF emitted by 280 household appliances were characterised. • Strongest emitters were induction cookers, CFLs, LCD-TVs, and microwave ovens. • No

Measurements of intermediate-frequency electric and magnetic fields in households

International Nuclear Information System (INIS)

Aerts, Sam; Calderon, Carolina; Valič, Blaž; Maslanyj, Myron; Addison, Darren; Mee, Terry; Goiceanu, Cristian; Verloock, Leen; Van den Bossche, Matthias; Gajšek, Peter; Vermeulen, Roel; Röösli, Martin; Cardis, Elisabeth; Martens, Luc; Joseph, Wout

2017-01-01

Historically, assessment of human exposure to electric and magnetic fields has focused on the extremely-low-frequency (ELF) and radiofrequency (RF) ranges. However, research on the typically emitted fields in the intermediate-frequency (IF) range (300 Hz to 1 MHz) as well as potential effects of IF fields on the human body remains limited, although the range of household appliances with electrical components working in the IF range has grown significantly (e.g., induction cookers and compact fluorescent lighting). In this study, an extensive measurement survey was performed on the levels of electric and magnetic fields in the IF range typically present in residences as well as emitted by a wide range of household appliances under real-life circumstances. Using spot measurements, residential IF field levels were found to be generally low, while the use of certain appliances at close distance (20 cm) may result in a relatively high exposure. Overall, appliance emissions contained either harmonic signals, with fundamental frequencies between 6 kHz and 300 kHz, which were sometimes accompanied by regions in the IF spectrum of rather noisy, elevated field strengths, or much more capricious spectra, dominated by 50 Hz harmonics emanating far in the IF domain. The maximum peak field strengths recorded at 20 cm were 41.5 V/m and 2.7 A/m, both from induction cookers. Finally, none of the appliance emissions in the IF range exceeded the exposure summation rules recommended by the International Commission on Non-Ionizing Radiation Protection guidelines and the International Electrotechnical Commission (IEC 62233) standard at 20 cm and beyond (maximum exposure quotients EQ E 1.0 and E Q H 0.13). - Highlights: • Survey of residential electric and magnetic fields at intermediate frequencies (IF). • IF-EF and -MF emitted by 280 household appliances were characterised. • Strongest emitters were induction cookers, CFLs, LCD-TVs, and microwave ovens. • No emissions exceeded

Calorimetric Measurement for Internal Conversion Efficiency of Photovoltaic Cells/Modules Based on Electrical Substitution Method

Science.gov (United States)

Saito, Terubumi; Tatsuta, Muneaki; Abe, Yamato; Takesawa, Minato

2018-02-01

We have succeeded in the direct measurement for solar cell/module internal conversion efficiency based on a calorimetric method or electrical substitution method by which the absorbed radiant power is determined by replacing the heat absorbed in the cell/module with the electrical power. The technique is advantageous in that the reflectance and transmittance measurements, which are required in the conventional methods, are not necessary. Also, the internal quantum efficiency can be derived from conversion efficiencies by using the average photon energy. Agreements of the measured data with the values estimated from the nominal values support the validity of this technique.

Membranas cerámicas y su utilidad en procesos de separación

Directory of Open Access Journals (Sweden)

Hernández, A.

1999-06-01

Full Text Available Among the separation processes in the industry, those using membranes are usually considered as forming a new and promising field. From them, those which use ceramic membranes, which can be manufactured more selective now than some time ago, are especially relevant due to their high mechanic, thermal and chemical resistances. Here we will start by a summary description of the methods of synthesis of inorganic membranes and particularly ceramic ones. Traditional methods are presented as well as both the polymeric and the coloidal sol-gel techniques. In order to characterize them, pore size distributions and surface properties, including morphology, hydrophillicity and electrical properties should be investigated. Some techniques to study these structural and surface properties are summarily presented. The ceramic membranes can substitute polymeric ones in most of their typical applications with profit due to their better performances and durability.

Entre los procesos industriales de separación, los que se basan en membranas se consideran como un nuevo y prometedor campo en desarrollo. Entre éstos, los basados en el uso de membranas cerámicas por sus características de resistencia mecánica, térmica y química y cada vez mayor selectividad han adquirido una gran relevancia. En este trabajo se comenzará haciendo una breve descripción de los métodos de síntesis de membranas inorgánicas y en particular cerámicas. Se exponen tanto los métodos tradicionales como los de sol-gel por vías polimérica y coloidal. Para caracterizar estas membranas se deben obtener sus distribuciones de tamaño de poro y propiedades superficiales tanto morfológicas como relacionadas con la hidrofílicidad y sus propiedades eléctricas. Algunas técnicas de investigación de estas propiedades estructurales y superficiales se exponen también resumidamente. Las membranas cerámicas pueden usarse en las mismas aplicaciones que las membranas polim

Graphene Visualizes the Ion Distribution on Air-Cleaved mica

NARCIS (Netherlands)

Bampoulis, Pantelis; Sotthewes, Kai; Siekman, Martin Herman; Zandvliet, Henricus J.W.; Poelsema, Bene

2017-01-01

The distribution of potassium (K+) ions on air-cleaved mica is important in many interfacial phenomena such as crystal growth, self-assembly and charge transfer on mica. However, due to experimental limitations to nondestructively probe single ions and ionic domains, their exact lateral organization

Measurements of plasma density fluctuations and electric wave fields using spherical electrostatic probes

International Nuclear Information System (INIS)

Eriksson, A.I.; Bostroem, R.

1995-04-01

Spherical electrostatic probes are in wide use for the measurements of electric fields and plasma density. This report concentrates on the measurements of fluctuations of these quantities rather than background values. Potential problems with the technique include the influence of density fluctuations on electric field measurements and vice versa, effects of varying satellite potential, and non-linear rectification in the probe and satellite sheaths. To study the actual importance of these and other possible effects, we simulate the response of the probe-satellite system to various wave phenomena in the plasma by applying approximate analytical as well as numerical methods. We use a set of non-linear probe equations, based on probe characteristics experimentally obtained in space, and therefore essentially independent of any specific probe theory. This approach is very useful since the probe theory for magnetized plasmas is incomplete. 47 refs

Monitoring Induced Fractures with Electrical Measurements using Depth to Surface Resistivity: A Field Case Study

Science.gov (United States)

Wilt, M.; Nieuwenhuis, G.; Sun, S.; MacLennan, K.

2016-12-01

Electrical methods offer an attractive option to map induced fractures because the recovered anomaly is related to the electrical conductivity of the injected fluid in the open (propped) section of the fracture operation. This is complementary to existing micro-seismic technology, which maps the mechanical effects of the fracturing. In this paper we describe a 2014 field case where a combination of a borehole casing electrode and a surface receiver array was used to monitor hydrofracture fracture creation and growth in an unconventional oil field project. The fracture treatment well was 1 km long and drilled to a depth of 2.2 km. Twelve fracture events were induced in 30 m intervals (stages) in the 1 km well. Within each stage 5 events (clusters) were initiated at 30 m intervals. Several of the fracture stages used a high salinity brine, instead of fresh water, to enhance the electrical signal. The electrical experiment deployed a downhole source in a well parallel to the treatment well and 100 m away. The source consisted of an electrode attached to a wireline cable into which a 0.25 Hz square wave was injected. A 60-station electrical field receiver array was placed above the fracture and extending for several km. Receivers were oriented to measure electrical field parallel with the presumed fracture direction and those perpendicular to it. Active source electrical data were collected continuously during 7 frac stages, 3 of which used brine as the frac fluid over a period of several days. Although the site was quite noisy and the electrical anomaly small we managed to extract a clear frac anomaly using field separation, extensive signal averaging and background noise rejection techniques. Preliminary 3D modeling, where we account for current distribution of the casing electrode and explicitly model multiple thin conductive sheets to represent fracture stages, produces a model consistent with the field measurements and also highlights the sensitivity of the

Molt de química! Diversos mètodes per determinar experimentalment la constant d'Avogrado

OpenAIRE

Domínguez Martínez, Álvaro

2013-01-01

Aquest article és un resum del treball de recerca de batxillerat titulat Molt de química!, que consisteix en un estudi sobre la constant d'Avogadro. Els dos objectius principals del treball són explicar la història que hi ha darrere d'aquest «número màgic» i dur a terme una investigació destinada a descobrir i explicar alguns experiments pels quals es podria estimar fàcilment el valor d'aquesta constant. Dels cinc experiments diferents que s'han realitzat a partir de electròlisi de l'aigua en...

Effect of Mica and Hematite (001) Surfaces on the Precipitation of Calcite

OpenAIRE

Huifang Xu; Mo Zhou; Yihang Fang; H. Henry Teng

2018-01-01

The substrate effect of mica and hematite on the nucleation and crystallization of calcite was investigated using scanning electron microscope (SEM), X-ray diffraction (XRD), and electron backscatter diffraction (EBSD) methods. On mica, we found, in the absence of Mg2+, the substrates’ (001) surfaces with hexagonal and pseudo-hexagonal two-dimensional (2-D) structure can affect the orientation of calcite nucleation with calcite (001) ~// mica (001) and calcite (010) ~// mica (010) to be the m...

Electric field measurements in high pressure discharges

International Nuclear Information System (INIS)

Mitko, S.V.; Ochkin, V.N.; Serdyuchenko, A.Yu.; Tskhai, S.N.

2001-01-01

Electric fields define a wide range of interactions and phenomena at different phases of matter both on micro- and macro-level. Investigation of electric fields behavior provides a key for understanding of these phenomena and their application

Evaluation of electrical impedance ratio measurements in accuracy of electronic apex locators

Directory of Open Access Journals (Sweden)

Pil-Jong Kim

2015-05-01

Full Text Available Objectives The aim of this paper was evaluating the ratios of electrical impedance measurements reported in previous studies through a correlation analysis in order to explicit it as the contributing factor to the accuracy of electronic apex locator (EAL. Materials and Methods The literature regarding electrical property measurements of EALs was screened using Medline and Embase. All data acquired were plotted to identify correlations between impedance and log-scaled frequency. The accuracy of the impedance ratio method used to detect the apical constriction (APC in most EALs was evaluated using linear ramp function fitting. Changes of impedance ratios for various frequencies were evaluated for a variety of file positions. Results Among the ten papers selected in the search process, the first-order equations between log-scaled frequency and impedance were in the negative direction. When the model for the ratios was assumed to be a linear ramp function, the ratio values decreased if the file went deeper and the average ratio values of the left and right horizontal zones were significantly different in 8 out of 9 studies. The APC was located within the interval of linear relation between the left and right horizontal zones of the linear ramp model. Conclusions Using the ratio method, the APC was located within a linear interval. Therefore, using the impedance ratio between electrical impedance measurements at different frequencies was a robust method for detection of the APC.

In situ measurement system of electric resistivity for outcrop investigation; Roto de shiyodekiru denkihi teiko keisoku system

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, K; Tamura, T [Osaka City Univ., Osaka (Japan). Faculty of Science; Morikawa, T [Osaka Prefectural Government, Osaka (Japan)

1997-05-27

A simplified electrical resistivity measuring device has been developed as a trial for field and laboratory uses, and some measurements were conducted. For this device, four probe electrodes are penetrated in the clay specimen, to calculate the resistivity from the voltage between both ends of the reference resistance connected with current electrodes in a series and the voltage between intermediate two voltage electrodes. It can be used in the field measurements. For the measurements, specimens of marine and lacustrine clayey sediments with clear stratigraphic levels in southern Osaka Group were used. In the laboratory, in addition to basic physical tests, diatom analysis and measurements of conductivity of clay suspension were also conducted. As a result of the experiments, the electric resistivity of marine clay obtained at the outcrop was lower than lacustrine clay as expected. The value of the former was a half of that of the latter. The frequency dependence in the high frequency region above 1 MHz was the reverse. The difference in electrical resistivity values between non-agitated specimens was about four times. The electrical resistivity of clay suspensions varied in two orders. 3 refs., 9 figs.

PLACAS CERÂMICAS - UMA INTRODUÇÃO

Directory of Open Access Journals (Sweden)

Carlos Maurício F. Vieira

2010-05-01

Full Text Available Este trabalho tem por objetivo apresentar uma revisão geral sobre as principais características exigidas para a obtenção de placas cerâmicas (pisos e revestimentos. As principais rotas de processamento são discutidas. Dados de mercado são apresentados com a finalidade de mostrar a importância e a situação atual da indústria cerâmica nacional no setor de pisos e revestimentos.

TICs en la enseñanza de la Química: Propuesta de evaluación de Laboratorios Virtuales de Química (LVQs

Directory of Open Access Journals (Sweden)

Cataldi, Zulma

2012-01-01

Full Text Available Los LVQs son unas nuevas formas de enseñanza de la química a través del uso de TICs. En este contexto se presenta el relevamiento de los laboratorios virtuales de química (LVQs más apropiados para la enseñanza de la química. Se analizan las ventajas de su aplicación en química básica y se delinean las pautas para su evaluación y selección de acuerdo a los indicadores propuestos, articulados con el marco teórico y con las dimensiones de análisis. Se propone una evaluación centrada en tres ejes: a dimensiones tecnológicas y técnicas, b dimensiones pedagógicas y c otras dimensiones como costo y comercialización. Se realizan pruebas de ajuste y aplicación del instrumento según los siguientes objetivos: a Analizar las estrategias didácticas docentes y la percepción en el uso de las TICs y b Delinear acciones formativas en didáctica de la química con uso de TICs.

Effect of Mica and Hematite (001 Surfaces on the Precipitation of Calcite

Directory of Open Access Journals (Sweden)

Huifang Xu

2018-01-01

Full Text Available The substrate effect of mica and hematite on the nucleation and crystallization of calcite was investigated using scanning electron microscope (SEM, X-ray diffraction (XRD, and electron backscatter diffraction (EBSD methods. On mica, we found, in the absence of Mg2+, the substrates’ (001 surfaces with hexagonal and pseudo-hexagonal two-dimensional (2-D structure can affect the orientation of calcite nucleation with calcite (001 ~// mica (001 and calcite (010 ~// mica (010 to be the major interfacial relationship. On hematite, we did not observe frequent twinning relationship between adjacent calcite gains, but often saw preferentially nucleation of calcite at surface steps on hematite substrate. We suggest that calcite crystals initially nucleate from the Ca2+ layers adsorbed on the surfaces. The pseudo-hexagonal symmetry on mica (001 surface also leads to the observed calcite (001 twinning. A second and less common orientation between calcite {104} and mica (001 was detected but could be due to local structure damage of the mica surface. Results in the presence of Mg2+ show that the substrate surfaces can weaken Mg toxicity to calcite nucleation and lead to a higher level of Mg incorporation into calcite lattice.

The time resolved measurement of ultrashort terahertz-band electric fields without an ultrashort probe

International Nuclear Information System (INIS)

Walsh, D. A.; Snedden, E. W.; Jamison, S. P.

2015-01-01

The time-resolved detection of ultrashort pulsed THz-band electric field temporal profiles without an ultrashort laser probe is demonstrated. A non-linear interaction between a narrow-bandwidth optical probe and the THz pulse transposes the THz spectral intensity and phase information to the optical region, thereby generating an optical pulse whose temporal electric field envelope replicates the temporal profile of the real THz electric field. This optical envelope is characterised via an autocorrelation based FROG (frequency resolved optical gating) measurement, hence revealing the THz temporal profile. The combination of a narrow-bandwidth, long duration, optical probe, and self-referenced FROG makes the technique inherently immune to timing jitter between the optical probe and THz pulse and may find particular application where the THz field is not initially generated via ultrashort laser methods, such as the measurement of longitudinal electron bunch profiles in particle accelerators

Filogenómica y genómica de la adaptación

OpenAIRE

Zardoya, Rafael; Sánchez-Gracia, Alejandro; Rozas Liras, Julio A.

2017-01-01

La posibilidad técnica actual de secuenciar genomas y transcriptomas completos de cualquier especie abre la puerta a cumplir la predicción de Darwin de poder reconstruir de forma rigurosa el árbol de la vida (las relaciones filogenéticas de todos los seres vivos actuales) mediante la filogenómica.

A setup for measuring the Seebeck coefficient and the electrical resistivity of bulk thermoelectric materials

Science.gov (United States)

Fu, Qiang; Xiong, Yucheng; Zhang, Wenhua; Xu, Dongyan

2017-09-01

This paper presents a setup for measuring the Seebeck coefficient and the electrical resistivity of bulk thermoelectric materials. The sample holder was designed to have a compact structure and can be directly mounted in a standard cryostat system for temperature-dependent measurements. For the Seebeck coefficient measurement, a thin bar-shaped sample is mounted bridging two copper bases; and two ceramic heaters are used to generate a temperature gradient along the sample. Two type T thermocouples are used to determine both temperature and voltage differences between two widely separated points on the sample. The thermocouple junction is flattened into a disk and pressed onto the sample surface by using a spring load. The flexible fixation method we adopted not only simplifies the sample mounting process but also prevents thermal contact deterioration due to the mismatch of thermal expansion coefficients between the sample and other parts. With certain modifications, the sample holder can also be used for four-probe electrical resistivity measurements. High temperature measurements are essential for thermoelectric power generation. The experimental system we developed is capable of measuring the Seebeck coefficient and the electrical resistivity of bulk thermoelectric materials in a wide temperature range from 80 to 500 K, which can be further extended to even higher temperatures. Measurements on two standard materials, constantan and nickel, confirmed the accuracy and the reliability of the system.

Electric Field Measurements At The Magnetopause

Science.gov (United States)

Lindqvist, P.-A.; Dunlop, M.

The quasi-thermal noise (QTN) is due to the thermal motions of the particles, which produce electrostatic fluctuations. This noise is detected by any sensitive receiver at the ports of an electric antenna immersed in a plasma and can be used to measure in-situ the plasma density, temperature and bulk velocity. The basic reason is that this noise can be formally calculated as a function of both the particle velocity distribu- tions and the antenna geometry. So, conversely, the "spectroscopy" of this noise re- veals the local plasma properties. This method is routinely used on various spacecraft (Ulysses, Wind) in the solar wind or in planetary magnetospheres/ionospheres (Image at Earth, Cassini at Venus, Earth and soon at Saturn). This method has the advantage of being relatively immune to spacecraft potential and photoelectrons pertubations, since it senses a large plasma volume. It provides an accurate measurement of the electron density (a few %) because it is based on the detection of the strong signal peak near the local plasma frequency (which is close to a resonance for electrostatic waves). We will show that QTN may be as well adapted to measure 1) magnetized (anisotropic) plasmas (and deduce the magnetic field strength), 2) suprathermal or non-thermal component (as for example a kappa distribution), and 3) a wide range of core temperature, i.e from ~10 eV, as in the solar wind, to rather low temperatures (tron density and temperature for comparison with our models of Mercury/solar wind interaction.

Measurements of Ozone, Lightning, and Electric Fields within Thunderstorms over Langmuir Laboratory, New Mexico

Science.gov (United States)

Eack, K. B.; Winn, W. P.; Rust, W. D.; Minschwaner, K.; Fredrickson, S.; Kennedy, D.; Edens, H. E.; Kalnajs, L. E.; Rabin, R. M.; Lu, G. P.; Bonin, D.

2008-12-01

A field project was conducted at the Langmuir Laboratory for Atmospheric Research during the summer of 2008 in an effort to better understand the direct production of ozone within electrically active storms. Five balloon flights were successfully launched into thunderstorms during this project. In situ measurements from the balloon instrument package included ozone mixing ratio, electric field strength, meteorological variables, and GPS location and timing. Lightning discharges were identified within each storm using a ground based lightning mapping array. The data show that the instruments ascended through regions of high electric fields within the sampled storms, and in some cases the balloon was in very close proximity to lightning. Relationships between electric field, lightning, and ozone observed during these flights will be discussed.

Improved method for measuring the electric fields in microwave cavity resonators

International Nuclear Information System (INIS)

Amato, J.C.; Herrmann, H.

1985-01-01

The electric field distribution in microwave cavities is commonly measured by frequency perturbation techniques. For many cavity modes which are important in accelerator applications, the standard bead-pulling technique cannot provide adequate discrimination between fields parallel and perpendicular to the particle trajectory, leading to inaccurate and ambiguous results. A method is described which substantially increases the directivity of the measurements. The method has been successfully used to determine the accelerator-related cavity parameters at frequencies up to three times the fundamental resonant frequency

Relaciones económicas bilaterales entre Ecuador y Brasil

OpenAIRE

Herrera Díaz, Stefany Natalie

2015-01-01

Dentro de la dinámica mundial actual, resulta de especial interés para Ecuador el análisis de sus relaciones económicas bilaterales con Brasil, debido al papel protagónico que ha alcanzado este país tanto a nivel regional como mundial. A nivel regional, varios de los países vecinos han delineado, incluso, su política exterior en función de potenciar sus relaciones políticas y económicas con él, y a nivel internacional, su participación en la geopolítica mundial es cada vez mayor. En términos ...

La argumentación en la formación de profesores de química: relaciones con la comprensión de la historia de la química

Directory of Open Access Journals (Sweden)

Pablo Antonio Archila

2014-01-01

Full Text Available En este artículo se trata el tema de la argumentación en ciencias de la naturaleza como habilidad de pensamiento y se promueve su inclusión en la formación inicial de profesores de química, pues se reconocen sus potencialidades para la mejora de las comprensiones que los futuros profesores podrían construir acerca de la historia de la química. Para tal fin, se aborda una breve revisión histórica de uno de los hitos de la química, como lo es el desarrollo de la química estructural, con lo cual se sugiere una de las actividades que forman parte de un módulo propuesto para la preparación en argumentación de profesores de química. Finalmente, se discuten algunas reflexiones y perspectivas que resultarían de la articulación entre argumentación e historia de la química.

Study of phosphorus implanted and annealed silicon by electrical measurements and ion channeling technique

CERN Document Server

Hadjersi, T; Zilabdi, M; Benazzouz, C

2002-01-01

We investigated the effect of annealing temperature on the electrical activation of phosphorus implanted into silicon. The measurements performed using spreading resistance, four-point probe and ion channeling techniques have allowed us to establish the existence of two domains of variation of the electrical activation (350-700 deg. C) and (800-1100 deg. C). The presence of reverse annealing and the annihilation of defects have been put in a prominent position in the first temperature range. It has been shown that in order to achieve a complete electrical activation, the annealing temperature must belong to the second domain (800-1100 deg. C).

Electric power: liberalization in half-measure

International Nuclear Information System (INIS)

Pradel, P.

1996-01-01

The European directive about the electric power liberalization concerns only big consumers. These manufacturers have privileged relations with E.D.F. for long years with a very attractive price for the kilowatt hour. The change should not be very important, only more transparency in accounts and change in tariffs of power transmission: for example, a small electric power producer will be authorized to contest the buying price that E.D.F. imposes to him to transport the energy he produces. (N.C.)

Dinámica ambiental y económica en la localidad de Puente Aranda en Bogotá

Directory of Open Access Journals (Sweden)

Carlos Fernando Parra Moreno

2014-01-01

Full Text Available Este documento muestra los resultados parciales de la investigación “Responsabilidad social y ambiental de la industria manufacturera en la localidad de Puente Aranda en la ciudad de Bogotá como alternativa al desarrollo humano integral sustentable”, realizados dentro del marco de trabajo del grupo de investigación Girsa. El estudio se basó en el análisis de la dinámica poblacional, ambiental y económica de la dicha localidad, a través de la metodología de la matriz de Vester. Con este instrumento se logró identificar las relaciones e interacciones dinámicas de todos los actores locales en el tiempo y en el espacio. Dentro de los problemas críticos que se encontraron en la localidad de Puente Aranda se encontró el agotamiento de fuentes hídricas, poca conciencia y educación ambiental de la población, una mala disposición de basuras, la no disponibilidad de servicios públicos para los nuevos asentamientos y altos niveles de emisión de partículas contaminantes.

Temas de Física para Ingeniería: Primer principio de la termodinámica

OpenAIRE

Beléndez Vázquez, Augusto

1992-01-01

Acústica, fluidos y termodinámica: "Primer principio de la termodinámica". Objetivos y caracteres generales de la termodinámica. Conceptos fundamentales de la termodinámica. Capacidad calorífica, calor específico y calor latente. Trabajo. Primer principio de la termodinámica: energía interna. Algunas aplicaciones del primer principio.

Measurement of gastrointestinal transmural electric potential difference in man.

Science.gov (United States)

Geall, M G; Code, C F; McIlrath, D C; Summerskill, W H

1970-01-01

Measurement, in man, of the electric potential difference between venous blood and the mucosal surface of the gastrointestinal tract gave identical values to the potential difference between mucosa and serosa. Various parts of the peritoneum were equipotential with venous blood. By contrast, skin-enteric potential difference varied with time and among different subjects because of a potential difference between skin and blood that is unpredictably reduced by skin injury. The results with electrolyte bridges of KCl in agar or of flowing KCl were identical.

Microestructura y comportamiento mecánico a altas temperaturas de cerámicas biomorficas de carburo de silicio

Directory of Open Access Journals (Sweden)

Martínez-Fernández, J.

2001-04-01

Full Text Available Environment conscious ceramics (ecoceramics are a new class of ceramic materials fabricated from natural wood (a renewable source. The affordable, net shape ceramics are fabricated by pyrolysis and molten silicon infiltration of wood preforms. The resulting materials have complex microstructure and multifunctional properties. The microstructure before and after high temperature plastic deformation was studied by scanning electron microscopy. These ceramics present regions of silicon and silicon carbide that follow the fibrous microstructure of the wood selected, resulting in a structure that resembles a continuos fiber composite. This structure results in very good mechanical properties as the evolutionary process has perfected it.

Las cerámicas respetuosas con el medio ambiente (ecocerámicas son una nueva clase de materiales cerámicos fabricados a partir de madera natural (un recurso renovable. Estas cerámicas se fabrican mediante la pirólisis de la preforma de madera e infiltración de silicio líquido en esta, proceso de bajo coste y con poco cambio de forma. El material resultante tiene una microestructura compleja y propiedades multifuncionales. La microestructura antes y después de la deformación plástica a alta temperatura se estudió mediante microscopía electrónica de barrido. Estas cerámicas presentan regiones de silicio y de carburo de silicio que mantienen la microestructura fibrosa de la madera seleccionada, similar a la de un material compuesto de fibra continua. Esta estructura ha resultado poseer unas muy buenas propiedades mecánicas a la compresión en caliente, en la dirección de las fibras, ya que el proceso evolutivo la ha perfeccionado.

Relative localization in wireless sensor networks for measurement of electric fields under HVDC transmission lines.

Science.gov (United States)

Cui, Yong; Wang, Qiusheng; Yuan, Haiwen; Song, Xiao; Hu, Xuemin; Zhao, Luxing

2015-02-04

In the wireless sensor networks (WSNs) for electric field measurement system under the High-Voltage Direct Current (HVDC) transmission lines, it is necessary to obtain the electric field distribution with multiple sensors. The location information of each sensor is essential to the correct analysis of measurement results. Compared with the existing approach which gathers the location information by manually labelling sensors during deployment, the automatic localization can reduce the workload and improve the measurement efficiency. A novel and practical range-free localization algorithm for the localization of one-dimensional linear topology wireless networks in the electric field measurement system is presented. The algorithm utilizes unknown nodes' neighbor lists based on the Received Signal Strength Indicator (RSSI) values to determine the relative locations of nodes. The algorithm is able to handle the exceptional situation of the output permutation which can effectively improve the accuracy of localization. The performance of this algorithm under real circumstances has been evaluated through several experiments with different numbers of nodes and different node deployments in the China State Grid HVDC test base. Results show that the proposed algorithm achieves an accuracy of over 96% under different conditions.

Relative Localization in Wireless Sensor Networks for Measurement of Electric Fields under HVDC Transmission Lines

Directory of Open Access Journals (Sweden)

Yong Cui

2015-02-01

Full Text Available In the wireless sensor networks (WSNs for electric field measurement system under the High-Voltage Direct Current (HVDC transmission lines, it is necessary to obtain the electric field distribution with multiple sensors. The location information of each sensor is essential to the correct analysis of measurement results. Compared with the existing approach which gathers the location information by manually labelling sensors during deployment, the automatic localization can reduce the workload and improve the measurement efficiency. A novel and practical range-free localization algorithm for the localization of one-dimensional linear topology wireless networks in the electric field measurement system is presented. The algorithm utilizes unknown nodes’ neighbor lists based on the Received Signal Strength Indicator (RSSI values to determine the relative locations of nodes. The algorithm is able to handle the exceptional situation of the output permutation which can effectively improve the accuracy of localization. The performance of this algorithm under real circumstances has been evaluated through several experiments with different numbers of nodes and different node deployments in the China State Grid HVDC test base. Results show that the proposed algorithm achieves an accuracy of over 96% under different conditions.

Estudio de los pigmentos de la cerámica ceremonial Moche con ayuda de un microscopio electrónico de barrido

Directory of Open Access Journals (Sweden)

1997-01-01

Full Text Available ÉTUDE DES PIGMENTS DE LA POTERIE CEREMONIELLE MOCHE A L’AIDE D’UN MICROSCOPE ELECTRONIQUE À BALAYAGE. Une collection de 22 tessons de céramique appartenant à autant de vases peints à l’aide d’une combinaison d’engobes rouges et blanches a été soumise à un examen au microscope électronique à balayage. L’objectif principal de cette étude consiste à déterminer la composition chimique des pigments constituant la couleur appliquée sur des vases cérémoniels ayant été trouvés près de la tombe Nº 5 située sur la Huaca de la Luna, l’une des deux plus importantes structures monumentales du site Moche de la côte nord du Pérou. Les résultats confirment l’utilisation d’oxides de fer, probablement de l’hématite, pour obtenir l’engobe rouge tandis que la calcite serait à la base de la production de l’engobe blanche. Les possibilités et les limites de cette méthode font l’objet d’une discussion. Una muestra de 22 fragmentos de cerámica, pertenecientes a una misma cantidad de vasos pintados con engobe blanco y rojo fue sometida a examen, empleando un microscopio electrónico de barrido. El objetivo central de este estudio fue el de determinar la composición química de los pigmentos que conforman los colores aplicados sobre las vasijas ceremoniales. Estas fueron halladas cerca de la tumba N° 5, localizada encima de la Huaca de la Luna, una de las dos estructuras monumentales del sitio de Moche en la costa norte del Perú. Los resultados confirman la utilización de óxidos de fierro, probablemente de hematita, para obtener el engobe rojo, mientras que la calcita sería la base para la producción del engobe blanco. Las posibilidades y los límites de este método son el objeto de discusión en este trabajo. SCANNING ELECTRON MICROSCOPE STUDY OF MOCHE CEREMONIAL POTTERY SLIPS. A study of 22 sherds selected from distinct vessels painted with red and white slips has been conducted with a scanning electron microscope

MICA diversity and linkage disequilibrium with HLA-B alleles in renal-transplant candidates in southern Brazil.

Science.gov (United States)

Yamakawa, Roger Haruki; Saito, Patrícia Keiko; Gelmini, Geórgia Fernanda; da Silva, José Samuel; Bicalho, Maria da Graça; Borelli, Sueli Donizete

2017-01-01

The major histocompatibility complex (MHC) class I chain-related gene A (MICA) is located centromerically to the human leukocyte antigen (HLA)-B. The short distance between these loci in the MHC indicates the presence of linkage disequilibrium (LD). Similarly to the HLA, the MICA is highly polymorphic, and this polymorphism has not been well documented in different populations. In this study, we estimated the allelic frequencies of MICA and the linkage disequilibrium with HLA-B alleles in 346 renal-transplant candidates in southern Brazil. MICA and HLA were typed using the polymerase chain reaction-sequence-specific primer method (PCR-SSO), combined with the Luminex technology. A total of 19 MICA allele groups were identified. The most frequent allele groups were MICA*008 (21.6%), MICA*002 (17.0%) and MICA*004 (14.8%). The most common haplotypes were MICA*009-B*51 (7.8%), MICA*004-B*44 (6.06%) and MICA*002-B*35 (5.63%). As expected from the proximity of the MICA and HLA-B loci, most haplotypes showed strong LD. Renal patients and healthy subjects in the same region of Brazil showed statistically significant differences in their MICA polymorphisms. The MICA*027 allele group was more frequent in renal patients (Pc = 0.018, OR: 3.421, 95% CI: 1.516-7.722), while the MICA*019 allele group was more frequent in healthy subjects (Pc = 0.001, OR: 0.027, 95% CI: 0.002-0.469). This study provided information on the distribution of MICA polymorphisms and linkage disequilibrium with HLA-B alleles in Brazilian renal-transplant candidates. This information should help to determine the mechanisms of susceptibility to different diseases in patients with chronic kidney disease, and to elucidate the mechanisms involved in allograft rejection associated with MICA polymorphisms in a Brazilian population.

Using X-ray photoelectron spectroscopy to discriminate among different sorption sites of micas: With implications for heterogeneous reduction of chromate at the mica-water interface

Energy Technology Data Exchange (ETDEWEB)

Ilton, E.S.; Moses, C.O.; Veblen, D.R.

2000-04-01

This contribution uses Cr2p and 3p binding energies (BEs) determined by X-ray photoelectron spectroscopy (XPS) to distinguish Cr{sup III} sorbed to different mica sorption sites. The results were used to better understand mechanisms for coupled sorption-reduction of Cr{sub (aq)}{sup VI} by ferrous micas. The research is important because: (1) Cr contamination is a serious and wide spread problem associated with a variety of industries; (2) Micas are important sorbents for Cr because they are ubiquitous, sorb cations and anions over a wide range of pH, and participate in heterogeneous redox reactions via structural Fe{sup II} and FE{sup III}; and (3) The mobility of cations sorbed by micas will depend, in part, on the dominant sorption site. Micas (two biotites, end member phologopite and muscovite) were reacted with Cr{sup III} solutions that contained variable concentrations of NaCl and KCl. Samples were extracted at times intervals and mica edge orientations were analyzed by ZPS. Cr{sub (aq)}{sup III} sorption was greater in Cr{sup III}-NaCl solutions relative to Cr{sup III}-KCl solutions. Cr2p and 3p BEs were bracketed by those for Cr{sup III} in the structure of silicates and in Cr{sup III}-oxyhydroxides. The BE of Cr{sup III} sorbed to micas was higher by about 0.3 eV after reaction with Cr{sup III}-NaCl solutions compared to Cr{sup III}-KCl aqueous solutions. At the experimental conditions, Na{sup +} and K{sup +} differentially block permanent charge sites but not variably charged edge sites of micas. Using the constraints inherent in the experimental design, the authors interpret the difference in CR{sup III} BE between the Cr{sup III}-NaCl and Cr{sup III}-KCl experiments to reflect a change in the dominant sorption site, where high and low Cr BEs indicate Cr sorbed by the interlamellar region and variably charged functional groups at mica edges, respectively. They conclude that small BE shifts for cations sorbed to silicates can be interpreted with

Alfabetización económica y actitudes hacia la compra en universitarios posterior a un programa de educación económica

Directory of Open Access Journals (Sweden)

Marianela Denegri Coria

2016-01-01

después de participar en el programa de Educación Económica se les aplicó la Escala de Actitudes hacia la Compra y el Consumo y el Test de Alfabetización Económica para adultos (TAE-A. Los resultados indican una menor tendencia hacia la impulsividad en la compra y el consumo en los estudiantes después de participar en la intervención. Las implicancias de este estudio enfatizan la necesidad de crear tempranamente programas de formación económica para favorecer el cambio actitudinal y el consumo reflexivo.

EVALUACIÓN DEL NIVEL DE ADOPCIÓN DE INTERNET EN LAS UNIVERSIDADES CHILENAS EN BASE AL MODELO eMICA EVALUATION OF THE INTERNET ADOPTION LEVEL IN CHILEAN UNIVERSITIES BASED ON THE eMICA MODEL

Directory of Open Access Journals (Sweden)

Narciso Cerpa

2007-12-01

Full Text Available Este estudio investiga el grado de adopción de las tecnologías de Internet en las universidades chilenas, como sistema de promoción y coordinación de sus actividades, considerando el rol de esta tecnología en la comunicación efectiva con los diferentes actores sociales que se relacionan con la universidad, tales como empresas, instituciones, personas y postulantes. Esta plataforma tecnológica también juega un rol a diario y muy importante en la comunicación entre miembros internos: administrativos, académicos y alumnos. El estudio consistió en el análisis de los sitios Web de todas las universidades chilenas bajo la metodología, eMICA, un modelo extendido de adopción de comercio electrónico en Internet [3]. Los resultados de este estudio indican que las universidades en general hacen un buen uso de las tecnologías de Internet que permite a una gran mayoría (98,3% de éstas, realizar promoción y suministro de información con un alto grado de sofisticación e interactividad (etapa 2, nivel 3 del modelo eMICA. Además, gran parte (75% de las universidades nacionales muestran un alto grado de adopción de tecnologías de Internet, ya que cuentan con aplicaciones (administrativas, académicas, promocionales, etc. que permiten hacer transacciones por medio de la Web y, por lo tanto, se encuentran en la etapa más alta, procesamiento, de acuerdo al modelo utilizado.The main objective of this study is to investigate the degree of Internet technologies adoption in by chilean universities. These universities use the Web as a promotion system and for the coordination of their operational activities, highlighting the role of this technology in the effective communication between the different social actors that interact with the university, namely, enterprises, institutions, people and potential students. This Web-based platform plays also an important role in daily communication among administrative staff, faculty, and students. This

Experiencias divertidas de electroquímica casera

OpenAIRE

Santiago Heredia-Avalos

2007-01-01

La química, dentro de la cual se incluye la electroquímica, es una materia que los estudiantes suelen ver como complicada, aburrida, carente de interés y que, además requiere de material de laboratorio sofisticado y reactivos químicos inaccesibles. Nada más lejos de la realidad, tal y como se pondrá de manifiesto en este trabajo, donde se proponen varias experiencias sencillas usando sustancias baratas, la mayoría de las cuales pueden encontrarse en un supermercado, y utensilio...

Scrophulariaceae endémicas del Perú

Directory of Open Access Journals (Sweden)

Blanca León

2013-10-01

Full Text Available La familia Scrophulariaceae es reconocida en el Perú por presentar alrededor de 18 géneros y 35 especies (Brako & Zarucchi, 1993; Ulloa Ulloa et al., 2004, principalmente herbáceas. En este trabajo reconocemos dos especies endémicas en dos géneros, las cuales se encuentran principalmente en la región Bosques Húmedos Amazónicos, entre los 200 y 1000 m de altitud. Ninguna de las especies endémicas se encuentra representada dentro del Sistema Nacional de Áreas Naturales Protegidas por el Estado.

Oleaceae endémicas del Perú

Directory of Open Access Journals (Sweden)

Isidoro Sánchez

2013-10-01

Full Text Available La familia Oleaceae es reconocida en el Perú por presentar seis géneros y 13 especies (Brako & Zarucchi, 1993, la mayoría árboles. En este trabajo reconocemos dos especies endémicas en igual número de géneros. Las especies endémicas han sido encontradas en las regiones Matorral Desértico y Bosques Húmedos Amazónicos, entre los 250 y 1850 m de altitud. Ambas especies se encuentran dentro del Sistema Nacional de Áreas Naturales Protegidas por el Estado.

Monitoring of In-Situ Remediation By Time Lapse 3D Geo-Electric Measurements

Science.gov (United States)

Kanli, A. I.; Tildy, P.; Neducza, B.; Nagy, P.; Hegymegi, C.

2017-12-01

Injection of chemical oxidant solution to degrade the subsurface contaminants can be used for hydrocarbon contamination remediation. In this study, we developed a non-destructive measurement strategy to monitor oxidative in-situ remediation processes. The difficulties of the presented study originate from the small volume of conductive solution that can be used due to environmental considerations. Due to the effect of conductive groundwater and the high clay content of the targeted layer and the small volume of conductive solution that can be used due to environmental considerations, a site specific synthetic modelling is necessary for measurement design involving the results of preliminary 2D ERT measurements, electrical conductivity measurements of different active agents and expected resistivity changes calculated by soil resistivity modelling. Because of chemical biodegradation, the results of soil resistivity modelling have suggested that the reagent have complex effects on contaminated soils. As a result the plume of resistivity changes caused by the injected agent was determined showing strong fracturing effect because of the high pressure of injection. 3D time-lapse geo-electric measurements were proven to provide a usable monitoring tool for in-situ remediation as a result of our sophisticated tests and synthetic modelling.

Electrostatic sensors applied to the measurement of electric charge transfer in gas-solids pipelines

International Nuclear Information System (INIS)

Woodhead, S R; Denham, J C; Armour-Chelu, D I

2005-01-01

This paper describes the development of a number of electric charge sensors. The sensors have been developed specifically to investigate triboelectric charge transfer which takes place between particles and the pipeline wall, when powdered materials are conveyed through a pipeline using air. A number of industrial applications exist for such gas-solids pipelines, including pneumatic conveyors, vacuum cleaners and dust extraction systems. The build-up of electric charge on pipelines and powdered materials can lead to electrostatic discharge and so is of interest from a safety viewpoint. The charging of powders can also adversely affect their mechanical handling characteristics and so is of interest to handling equipment engineers. The paper presents the design of the sensors, the design of the electric charge test rig and electric charge measurement test results

Measurement of the hot electrical conductivity in the PBX-M tokamak

International Nuclear Information System (INIS)

Giruzzi, G.; Barbato, E.; Cardinali, A.; Bernabei, S.

1997-01-01

A new method for the analysis of tokamak discharges in which the plasma current is driven by the combination of high-power rf waves and a dc electric field is presented. In such regimes, which are the most usual in rf current drive experiments, it is generally difficult to separate the different components of the plasma current, i.e., purely Ohmic, purely noninductive and cross terms. If the bilinear (in wave power and electric field) cross term is the dominant one, an explicit relation between the loop voltage drop and the injected power can be found. This relation involves two parameters, the purely rf current drive efficiency and the hot (power dependent) electrical conductivity. These can be simultaneously determined from a simple two-parameter fit, if the loop voltage drop is measured at several rf power levels. An application to lower hybrid current drive experiments in the PBX-M tokamak is presented. It is shown that the method also allows the independent evaluation of the average power absorption fraction and n parallel upshift

Electric field measurements on Cluster: comparing the double-probe and electron drift techniques

Directory of Open Access Journals (Sweden)

A. I. Eriksson

2006-03-01

Full Text Available The four Cluster satellites each carry two instruments designed for measuring the electric field: a double-probe instrument (EFW and an electron drift instrument (EDI. We compare data from the two instruments in a representative sample of plasma regions. The complementary merits and weaknesses of the two techniques are illustrated. EDI operations are confined to regions of magnetic fields above 30 nT and where wave activity and keV electron fluxes are not too high, while EFW can provide data everywhere, and can go far higher in sampling frequency than EDI. On the other hand, the EDI technique is immune to variations in the low energy plasma, while EFW sometimes detects significant nongeophysical electric fields, particularly in regions with drifting plasma, with ion energy (in eV below the spacecraft potential (in volts. We show that the polar cap is a particularly intricate region for the double-probe technique, where large nongeophysical fields regularly contaminate EFW measurments of the DC electric field. We present a model explaining this in terms of enhanced cold plasma wake effects appearing when the ion flow energy is higher than the thermal energy but below the spacecraft potential multiplied by the ion charge. We suggest that these conditions, which are typical of the polar wind and occur sporadically in other regions containing a significant low energy ion population, cause a large cold plasma wake behind the spacecraft, resulting in spurious electric fields in EFW data. This interpretation is supported by an analysis of the direction of the spurious electric field, and by showing that use of active potential control alleviates the situation.

Quantitation of 24-Hour Moisturization by Electrical Measurements of Skin Hydration.

Science.gov (United States)

Wickett, R Randall; Damjanovic, Bronson

The purpose of this study was to quantify the effects of several moisturizers on hydration of the stratum corneum by measuring their effect on electrical conductance over a 24-hour period. Double-blind, randomized controlled trial. Twenty-five healthy female volunteers aged 18 to 65 years with dry skin on the lower legs and no other known dermatologic pathology participated in the study. Additional exclusion criteria were pregnant or taking anti-inflammatory steroids. The study was carried out in a clinical research facility in Winnipeg, Manitoba, Canada. Subjects underwent a 3-day conditioning period using a natural soap bar on the lower legs and no application of moisturizer to the skin. Participants then came to the test site and equilibrated for at least 30 minutes under controlled conditions of temperature and humidity. After baseline hydration measurements on test sites on the lower legs of each subject, a single application of each of 5 test products at a dose of 2 mg/cm was made. Skin hydration was assessed by electrical conductance measurements with a specialized probe. The probe was briefly placed on the skin surface with light pressure, and the measurement recorded in units of microsiemens (μS). Conductance was measured at 2, 4, 6, 8, and 24 hours after product applications. Although all but 1 of the test products increased conductance at 2 hours, only 2 moisturizers containing high levels of glycerin (products C and E) maintained increased conductance relative to baseline at 24 hours, +37.8 (P skin conductance for at least 24 hours after a single application.

El Área de Ciencia y Tecnologías Químicas del CSIC: ¿Un Área de químicas?

Directory of Open Access Journals (Sweden)

García-López, María Teresa

2002-08-01

Full Text Available Not available

El artículo titulado "El Area de Ciencia y Tecnologías Químicas del CSIC: ¿un Area de químicas?» pretende mostrar una breve panorámica del lugar que ocupa el género femenino dentro de la citada Area. En la primera parte se aportan las estadísticas que reflejan el número y porcentaje de científicas totales en los distintos Institutos del Area, así como su distribución entre las tres escalas de personal científico del Organismo. Una segunda parte está dedicada a recoger las aportaciones personales de varias científicas del Area acerca del tema, visto desde sus propias experiencias.

Dinámicas de la actividad científica del Instituto de Investigaciones Socio-Económicas de la Universidad Nacional de San Juan de Argentina

Directory of Open Access Journals (Sweden)

Gonzalo Miguel Castillo

2018-02-01

Full Text Available Este artículo fue un estudio de caso en torno a las capacidades de investigación generadas en el Instituto de Investigaciones Socio-Económicas de la Facultad de Ciencias Sociales, perteneciente a la Universidad Nacional de San Juan, en Argentina. Aborda los principales acontecimientos históricos de la institución y su dinámica actual, tuvo en cuenta las áreas de conocimiento en las cuales se desarrollan sus investigaciones. A su vez, este trabajo ha descrito las dinámicas de la revista académica producida en este instituto, denominada REVIISE. La metodología fue un abordaje objetivo/descriptivo. Se procedió a analizar el papel, devenir y accionar del IISE y las modalidades de proyectos de investigación ejecutados. Fueron indagados el funcionamiento de la REVIISE, identificando perfiles académicos de sus autores, circuitos de difusión y redes académicas; y la conformación de comités y consejos editoriales y académicos que componen esta publicación. Se propone realizar un recorrido que atraviesa lo institucional, los agentes académicos y la principal red de difusión de la producción de conocimiento para comprender las capacidades investigativas del Instituto de Investigaciones Socio Económicas.

Measurements of electric charge and screening length of microparticles in a plasma sheath

International Nuclear Information System (INIS)

Nakamura, Y.; Ishihara, O.

2009-01-01

An experiment is described in which microparticles are levitated within a rf sheath above a conducting plate in argon plasma. The microparticles forming a two-dimensional crystal structure are considered to possess Debye screening Coulomb potential φ(r)=(Q/4πε 0 r)exp(-r/λ), where Q is the electric charge, r is distance, and λ is the screening length. When the crystal structure is slanted with an angle θ, a particle experiences a force Mg sin θ, where M is the mass of the particle and g is acceleration due to gravity, which must be equal to the Debye screened Coulomb force from other particles. By changing θ, relations for λ(Q) are measured. The screening length λ and Q are determined uniquely from the crossing points of several relations. The electric charge Q is also estimated from a floating potential measured with a probe. The measured λ is nearly equal to an ion Debye length.

Morphology and thermal degradation study of poly(lactic acid)/synthetic mica composites

International Nuclear Information System (INIS)

Souza, D.H.S.; Dias, M.L.

2010-01-01

Poly(lactic acid) (PLA)/synthetic mica composites has been little studied in the literature. In this work, an organophilic synthetic mica was used to prepare PLA nanocomposites. The composites were obtained at an internal mixer containing 3, 5, 7 and 10 wt% of mica. The materials were analyzed by x-ray diffraction, thermogravimetric analysis and gel permeation chromatography. (author)

Electrical shielding box measurement of the negative hydrogen beam from Penning ion gauge ion source.

Science.gov (United States)

Wang, T; Yang, Z; Dong, P; long, J D; He, X Z; Wang, X; Zhang, K Z; Zhang, L W

2012-06-01

The cold-cathode Penning ion gauge (PIG) type ion source has been used for generation of negative hydrogen (H(-)) ions as the internal ion source of a compact cyclotron. A novel method called electrical shielding box dc beam measurement is described in this paper, and the beam intensity was measured under dc extraction inside an electrical shielding box. The results of the trajectory simulation and dc H(-) beam extraction measurement were presented. The effect of gas flow rate, magnetic field strength, arc current, and extraction voltage were also discussed. In conclusion, the dc H(-) beam current of about 4 mA from the PIG ion source with the puller voltage of 40 kV and arc current of 1.31 A was extrapolated from the measurement at low extraction dc voltages.

Measuring the electric field of few-cycle laser pulses by attosecond cross correlation

International Nuclear Information System (INIS)

Bandrauk, Andre D.; Chelkowski, Szczepan; Shon, Nguyen Hong

2002-01-01

A new technique for directly measuring the electric field of linearly polarized few-cycle laser pulses is proposed. Based on the solution of the time-dependent Schroedinger equation (TDSE) for an H atom in the combined field of infrared (IR) femtosecond (fs) and ultraviolet (UV) attosecond (as) laser pulses we show that, as a function of the time delay between two pulses, the difference (or equivalently, asymmetry) of photoelectron signals in opposite directions (along the polarization vector of laser pulses) reproduces very well the profile of the electric field (or vector potential) in the IR pulse. Such ionization asymmetry can be used for directly measuring the carrier-envelope phase difference (i.e., the relative phase of the carrier frequency with respect to the pulse envelope) of the IR fs laser pulse

A Test-Bench for Measurement of Electrical Static Parameters of Strip Silicon Detectors

CERN Document Server

Golutvin, I A; Danilevich, V G; Dmitriev, A Yu; Elsha, V V; Zamiatin, Y I; Zubarev, E V; Ziaziulia, F E; Kozus, V I; Lomako, V M; Stepankov, D V; Khomich, A P; Shumeiko, N M; Cheremuhin, A E

2003-01-01

An automated test-bench for electrical parameters input control of the strip silicon detectors, used in the End-Cap Preshower detector of the CMS experiment, is described. The test-bench application allows one to solve a problem of silicon detectors input control in conditions of mass production - 1800 detectors over 2 years. The test-bench software is realized in Delphi environment and contains a user-friendly operator interface for measurement data processing and visualization as well as up-to-date facilities for MS-Windows used for the network database. High operating characteristics and reliability of the test-bench were confirmed while more than 800 detectors were tested. Some technical solutions applied to the test-bench could be useful for design and construction of automated facilities for electrical parameters measurements of the microstrip detectors input control.

Electrical conductivity measurement and thermogravimetric study of chromium-doped uranium dioxide

International Nuclear Information System (INIS)

Matsui, Tsuneo; Naito, Keiji

1986-01-01

The electrical conductivity and nonstoichiometric composition of (Usub(1-y)Crsub(y))Osub(2+x) (y=0.001 and 0.05) were measured in the range 1173 -17 2 ) -2 Pa by the four inserted wires method and thermogravimetry, respectively. The electrical conductivities of (Usub(1-y)Crsub(y))Osub(2+x) (y=0.01 and 0.05) were about one-order lower than that of UOsub(2+x), probably due to the presence of the chromium ion as an electron donor. The activation energies of (Usub(0.99)Crsub(0.01))Osub(2+x) and (Usub(0.95)Crsub(0.05))Osub(2+x) for the extrinsic conduction in the low oxygen partial pressure region were calculated to be 24.7+-1.3 and 25.9+-1.0 kJ.mol -1 , respectively from the Arrhenius plots of the electrical conductivities. These small values of the activation energy of (Usub(1-y)Crsub(y))Osub(2+x) may suggest the presence of the hopping mechanism for hole conduction, similarly to the case of UOsub(2+x). From the oxygen partial pressure dependences of both the electrical conductivity and the deviation x in (Usub(1-y)Crsub(y))Osub(2+x), the defect structure was discussed with the complex defect model consisting of oxygen vacancies and two kinds of interstitial oxygens. (orig.)

Mössbauer spectra of white micas from the Central Western Carpathians Mountains

Science.gov (United States)

Sitek, J.; Sulák, M.; Putiš, M.; Tóth, I.

2010-03-01

Potassium white micas from the rocks included into Cretaceous deformation zones (ca. 100-70 Ma in age) of the Central Western Carpathians were investigated by Mössbauer spectroscopy. White micas formed during a polystage evolution and changing P-T conditions of their crystallization in crustal-scale shear zones. We found criteria for distinguishing generations of celadonite-poor (muscovitic) and celadonite-rich (phengitic) white micas using Mössbauer spectroscopy. This method revealed contrasting spectra characterized by typical quadrupole doublets corresponding to Fe2+ Fe3+ contents in white micas. They are in the range of 2.9-3.0 mm/s for phengite, and 2.6-2.7 mm/s for muscovite. Mössbauer spectra reflect well the chemical changes in white mica aggregates, especially of those close to the end-member muscovite and (alumino-)celadonite compositions.

Clinical relevance of pre and post-transplant immune markers in kidney allograft recipients: anti-HLA and MICA antibodies and serum levels of sCD30 and sMICA.

Science.gov (United States)

Solgi, Ghasem; Furst, Daniel; Mytilineos, Joannis; Pourmand, Gholamreza; Amirzargar, Ali Akbar

2012-03-01

This retrospective study aims to determine the prognostic values of HLA and MICA antibodies, serum levels of sCD30 and soluble form of MHC class I related chain A (sMICA) in kidney allograft recipients. Sera samples of 40 living unrelated donor kidney recipients were tested by ELISA and Flow beads techniques for the presence of anti HLA and MICA antibodies and the contents of sCD30 and sMICA. HLA and MICA antibody specification was performed by LABScreen single antigen beads to determine whether the antibodies were directed against donor mismatches. Within first year post operatively 9 of 40 patients (22.5%) showed acute rejection episodes (ARE) that four of them lost their grafts compared to 31 functioning transplants (P=0.001). The presence of HLA antibodies before and after transplantation was significantly associated with ARE (P=0.01 and P=0.02 respectively). Sensitization to HLA class II antigens pre-transplant was strongly associated with higher incidence of ARE (P=0.004). A significant correlation was found between ARE and appearance of non-donor specific antibodies (P=0.02). HLA antibody positive patients either before or after transplantation showed lower graft survival rates than those without antibodies during three years follow-up (P=0.04 and P=0.02). Anti-MICA antibodies were observed in 8/40(20%) and 5/40(12.5%) of patients pre and post-transplant respectively. Coexistence of HLA and MICA antibodies was shown in 2 of 4 cases with graft loss. A significant increased level of sCD30 at day 14 (P=0.001) and insignificant decreased levels of sMICA pre and post operatively were detected in rejecting transplants compared to functioning graft group. Our findings support the view that monitoring of HLA and MICA antibodies as well as sCD30 levels early after transplant has predictive value for early and late allograft dysfunctions and the presence of these factors are detrimental to graft function and survival. Copyright © 2012 Elsevier B.V. All rights

AVALIAÇÃO FÍSICA, QUÍMICA, BIOQUÍMICA E AGRONÔMICA DE CULTIVARES DE FEIJÃO-GUANDU (CAJANUS CAJAN (L MILL

Directory of Open Access Journals (Sweden)

SOLANGE GUIDOLIM CANNIATTI-BRAZACA

2009-07-01

Full Text Available

RESUMO: Foram estudadas as características físicas, químicas, bioquímicas e agronômicas de 40 cultivares de feijão-guandu (Cajanus cajan (L Mill provenientes da EMBRAPA de São Carlos (SP e originárias de diversas regiões do Brasil e da Índia. Pode-se observar entre os cultivares variações expressivas no tempo de cocção, no teor de lectinas e na produtividade. Os resultados obtidos quanto ao teor protéico e à digestibilidade do guandu, quando comparadas com os resultados obtidos na literatura, mostraram-se semelhantes aos dos grãos de feijão-comum. Pode-se, também, observar baixos teores de taninos entre os cultivares estudados. Foram selecionados três cultivares por apresentarem melhores características entre os parâmetros estudados. PALAVRAS-CHAVE: Feijão-guandu; proteínas; fatores antinutricionais; produtividade.

Global Electric Circuit Implications of Combined Aircraft Storm Electric Current Measurements and Satellite-Based Diurnal Lightning Statistics

Science.gov (United States)

Mach, Douglas M.; Blakeslee, Richard J.; Bateman, Monte G.

2011-01-01

Using rotating vane electric field mills and Gerdien capacitors, we measured the electric field profile and conductivity during 850 overflights of thunderstorms and electrified shower clouds (ESCs) spanning regions including the Southeastern United States, the Western Atlantic Ocean, the Gulf of Mexico, Central America and adjacent oceans, Central Brazil, and the South Pacific. The overflights include storms over land and ocean, and with positive and negative fields above the storms. Over three-quarters (78%) of the land storms had detectable lightning, while less than half (43%) of the oceanic storms had lightning. Integrating our electric field and conductivity data, we determined total conduction currents and flash rates for each overpass. With knowledge of the storm location (land or ocean) and type (with or without lightning), we determine the mean currents by location and type. The mean current for ocean thunderstorms is 1.7 A while the mean current for land thunderstorms is 1.0 A. The mean current for ocean ESCs 0.41 A and the mean current for land ESCs is 0.13 A. We did not find any significant regional or latitudinal based patterns in our total conduction currents. By combining the aircraft derived storm currents and flash rates with diurnal flash rate statistics derived from the Lightning Imaging Sensor (LIS) and Optical Transient Detector (OTD) low Earth orbiting satellites, we reproduce the diurnal variation in the global electric circuit (i.e., the Carnegie curve) to within 4% for all but two short periods of time. The agreement with the Carnegie curve was obtained without any tuning or adjustment of the satellite or aircraft data. Given our data and assumptions, mean contributions to the global electric circuit are 1.1 kA (land) and 0.7 kA (ocean) from thunderstorms, and 0.22 kA (ocean) and 0.04 (land) from ESCs, resulting in a mean total conduction current estimate for the global electric circuit of 2.0 kA. Mean storm counts are 1100 for land

Direct measurement of macroscopic electric fields produced by collective effects in electron-impact experiments

International Nuclear Information System (INIS)

Velotta, R.; Avaldi, L.; Camilloni, R.; Giammanco, F.; Spinelli, N.; Stefani, G.

1996-01-01

The macroscopic electric field resulting from the space charge produced in electron-impact experiments has been characterized by using secondary electrons of well-defined energy (e.g., Auger or autoionizing electrons) as a probe. It is shown that the measurement of the kinetic-energy shifts suffered by secondary electrons is a suitable tool for the analysis of the self-generated electric field in a low-density plasma. copyright 1996 The American Physical Society

Electric field measurements in a nanosecond pulse discharge by picosecond CARS/4-wave mixing

Science.gov (United States)

Goldberg, Ben; Shkurenkov, Ivan; Adamovich, Igor; Lempert, Walter

2014-10-01

Time-resolved electric field measurements in hydrogen by picosecond CARS/4-wave mixing are presented. Measurements are carried out in a high voltage nanosecond pulse discharge in hydrogen in plane-to-plane geometry, at pressures of up to several hundred Torr, and with a time resolution of 0.2 ns. Absolute calibration of the diagnostics is done using a sub-breakdown high voltage pulse of 12 kV/cm. A diffuse discharge is obtained by applying a peak high voltage pulse of 40 kV/cm between the electrodes. It is found that breakdown occurs at a lower field, 15--20 kV/cm, after which the field in the plasma is reduced rapidly due to plasma self shielding The experimental results are compared with kinetic modeling calculations, showing good agreement between the measured and the predicted electric field.

O uso de técnica eletroquímica para a descontaminação de estruturas cerâmicas vítreas porosas

OpenAIRE

Assis,O. B. G.; Silva,E. R.

2010-01-01

Apresentamos neste trabalho os resultados de ensaios preliminares para avaliar o uso de técnica de eletro-osmose para a remoção de contaminantes orgânicos em estruturas porosas cerâmicas, como filtros ou similares. A técnica consiste em forçar a migração de contaminantes retidos na estrutura interna ou na superfície dos poros por meio da aplicação de tensão controlada em célula eletroquímica projetada para este fim. As moléculas absorvidas na superfície cerâmica estarão sujeitas as ações cisa...

Methodology to measure strains at high temperatures using electrical strain gages with free filaments

International Nuclear Information System (INIS)

Atanazio Filho, Nelson N.; Gomes, Paulo T. Vida; Scaldaferri, Denis H.B.; Silva, Luiz L. da; Rabello, Emerson G.; Mansur, Tanius R.

2013-01-01

An experimental methodology used for strains measuring at high temperatures is show in this work. In order to do the measurements, it was used electric strain gages with loose filaments attached to a stainless steel 304 beam with specific cements. The beam has triangular shape and a constant thickness, so the strain is the same along its length. Unless the beam surface be carefully prepared, the strain gage attachment is not efficient. The showed results are for temperatures ranging from 20 deg C to 300 deg C, but the experimental methodology could be used to measure strains at a temperature up to 900 deg C. Analytical calculations based on solid mechanics were used to verify the strain gage electrical installation and the measured strains. At a first moment, beam deformations as a temperature function were plotted. After that, beam deformations with different weighs were plotted as a temperature function. The results shown allowed concluding that the experimental methodology is trustable to measure strains at temperatures up to 300 deg C. (author)

PNPI differential EDM spectrometer and latest results of measurements of the neutron electric dipole moment

Energy Technology Data Exchange (ETDEWEB)

Serebrov, A. P., E-mail: serebrov@pnpi.spb.ru; Kolomenskiy, E. A.; Pirozhkov, A. N.; Krasnoshchekova, I. A.; Vasiliev, A. V.; Polyushkin, A. O.; Lasakov, M. S.; Murashkin, A. N.; Solovey, V. A.; Fomin, A. K.; Shoka, I. V.; Zherebtsov, O. M. [National Research Center Kurchatov Institute, Petersburg Nuclear Physics Institute (Russian Federation); Alexandrov, E. B.; Dmitriev, S. P.; Dovator, N. A. [Russian Academy of Sciences, Ioffe Physical Technical Institute (Russian Federation); Geltenbort, P.; Ivanov, S. N.; Zimmer, O. [Institut Max von Laue–Paul Langevin (France)

2015-12-15

In this work, the double chamber magnetic resonance spectrometer of the Petersburg Nuclear Physics Institute (PNPI) designed to measure the neutron electric dipole moment (EDM) is briefly described. A method for long storage of polarized ultracold neutrons in a resonance space with a superposed electric field collinear to the leading magnetic field is used. The results of the measurements carried out on the ILL reactor (Grenoble, France) are interpreted as the upper limit of the value of neutron EDM vertical bar d{sub n} vertical bar < 5.5 × 10{sup –26}e cm at the 90% confidence level.

Electrical conductivity measurement of excised human metastatic liver tumours before and after thermal ablation.

Science.gov (United States)

Haemmerich, Dieter; Schutt, David J; Wright, Andrew W; Webster, John G; Mahvi, David M

2009-05-01

We measured the ex vivo electrical conductivity of eight human metastatic liver tumours and six normal liver tissue samples from six patients using the four electrode method over the frequency range 10 Hz to 1 MHz. In addition, in a single patient we measured the electrical conductivity before and after the thermal ablation of normal and tumour tissue. The average conductivity of tumour tissue was significantly higher than normal tissue over the entire frequency range (from 4.11 versus 0.75 mS cm(-1) at 10 Hz, to 5.33 versus 2.88 mS cm(-1) at 1 MHz). We found no significant correlation between tumour size and measured electrical conductivity. While before ablation tumour tissue had considerably higher conductivity than normal tissue, the two had similar conductivity throughout the frequency range after ablation. Tumour tissue conductivity changed by +25% and -7% at 10 Hz and 1 MHz after ablation (0.23-0.29 at 10 Hz, and 0.43-0.40 at 1 MHz), while normal tissue conductivity increased by +270% and +10% at 10 Hz and 1 MHz (0.09-0.32 at 10 Hz and 0.37-0.41 at 1 MHz). These data can potentially be used to differentiate tumour from normal tissue diagnostically.

Release isentrope measurements with the LLNL electric gun

Energy Technology Data Exchange (ETDEWEB)

Gathers, G.R.; Osher, J.E.; Chau, H.H.; Weingart, R.C.; Lee, C.G.; Diaz, E.

1987-06-01

The liquid-vapor coexistence boundary is not well known for most metals because the extreme conditions near the critical point create severe experimental difficulties. The isentropes passing through the liquid-vapor region typically begin from rather large pressures on the Hugoniot. We are attempting to use the high velocities achievable with the Lawrence Livermore National Laboratory (LLNL) electric gun to obtain these extreme states in aluminum and measure the release isentropes by releasing into a series of calibrated standards with known Hugoniots. To achieve large pressure drops needed to explore the liquid-vapor region, we use argon gas for which Hugoniots have been calculated using the ACTEX code, as one of the release materials.

Actitudes y rendimiento académico: su evolución desde química general e inorgánica hasta química orgánica

Directory of Open Access Journals (Sweden)

María S. Reyes

2014-01-01

Full Text Available Esta investigación tiene un doble propósito, en primer lugar, valorar las actitudes hacia la química de alumnos universitarios de carreras biológicas en dos cursos relacionados con esta disciplina y, por otro lado, relacionar dichas actitudes con el rendimiento académico presentado por los estudiantes. El instrumento elegido para medir las actitudes de los alumnos fue un cuestionario según la escala Likert, encuestándose a la totalidad de estudiantes que cursaban cada uno de los cursos de química analizados: Química General e Inorgánica (QGI y Química Orgánica (QO. Para estimar el rendimiento académico se analizaron actas de parciales y se realizaron cálculos de correlación. Los alumnos que cursaban QGI presentaron actitudes hacia la química valoradas como indiferentes. Sin embargo al finalizar el curso de QO sus actitudes fueron evolucionando favorablemente, ya que la puntuación media obtenida para los ítems positivos y negativos estuvo en el rango de actitudes positivas. Los valores del coeficiente de Pearson obtenidos para los dos cursos estudiados fueron superiores a 0,80, lo que indica una fuerte relación entre las variables implicadas, por lo cual se infiere la importancia de desarrollar actitudes positivas hacia la química para favorecer el rendimiento académico de los alumnos.

Combined Aircraft and Satellite-Derived Storm Electric Current and Lightning Rates Measurements and Implications for the Global Electric Circuit

Science.gov (United States)

Mach, Douglas M.; Blakeslee, Richard J.; Bateman, Monte G.

2010-01-01

Using rotating vane electric field mills and Gerdien capacitors, we measured the electric field profile and conductivity during 850 overflights of electrified shower clouds and thunderstorms spanning regions including the Southeastern United States, the Western Atlantic Ocean, the Gulf of Mexico, Central America and adjacent oceans, Central Brazil, and the South Pacific. The overflights include storms over land and ocean, with and without lightning, and with positive and negative fields above the storms. The measurements were made with the NASA ER-2 and the Altus-II high altitude aircrafts. Peak electric fields, with lightning transients removed, ranged from -1.0 kV/m to 16 kV/m, with a mean value of 0.9 kV/m. The median peak field was 0.29 kV/m. Integrating our electric field and conductivity data, we determined total conduction currents and flash rates for each overpass. With knowledge of the storm location (land or ocean) and type (with or without lightning), we determine the mean currents by location and type. The mean current for ocean storms with lightning is 1.6 A while the mean current for land storms with lightning is 1.0 A. The mean current for oceanic storms without lightning (i.e., electrified shower clouds) is 0.39 A and the mean current for land storms without lightning is 0.13 A. Thus, on average, land storms with or without lightning have about half the mean current as their corresponding oceanic storm counterparts. Over three-quarters (78%) of the land storms had detectable lightning, while less than half (43%) of the oceanic storms had lightning. We did not find any significant regional or latitudinal based patterns in our total conduction currents. By combining the aircraft derived storm currents and flash rates with diurnal lightning statistics derived from the Lightning Imaging Sensor (LIS) and Optical Transient Detector (OTD) low Earth orbiting satellites, we reproduce the diurnal variation in the global electric circuit (i.e., the Carnegie

Measurement of full-field deformation induced by a dc electrical field in organic insulator films

Directory of Open Access Journals (Sweden)

Boudou L.

2010-06-01

Full Text Available Digital image correlation method (DIC using the correlation coefficient curve-fitting for full-field surface deformation measurements of organic insulator films is investigated in this work. First the validation of the technique was undertaken. The computer-generated speckle images and the measurement of coefficient of thermal expansion (CTE of aluminium are used to evaluate the measurement accuracy of the technique. In a second part the technique is applied to measure the mechanical deformation induced by electrical field application to organic insulators. For that Poly(ethylene naphthalene 2,6-dicarboxylate (PEN thin films were subjected to DC voltage stress and DIC provides the full-field induced deformations of the test films. The obtained results show that the DIC is a practical and robust tool for better comprehension of mechanical behaviour of the organic insulator films under electrical stress.

Measurement of the radial electric field in the ASDEX tokamak

International Nuclear Information System (INIS)

Field, A.R.; Fussmann, G.; Hofmann, J.V.

1990-12-01

The radial electric field (E Τ ) at the plasma periphery is determined by measuring the drift velocities of low-Z impurities ions (BIV, CIII and HeII). The measurements are performed with a scannable mirror system which allows the determination of the poloidal, perpendicular (to B vector) and toroidal components of the drift velocities from the differential Doppler shift of visible line emission observed along opposing viewing directions. The principle of the measurement is investigated in detail. In particular, it is shown that for radially localised emission shells there exits a line of sight oriented perpendicular to B vector along which E Τ may be inferred directly from the observed Doppler shift of the line emission. Along such a line of sight the net contribution to the shift from the diamagnetic drift and the radial gradient of the excitation probability is negligible. During the Ohmic- and L-phases the perpendicular drift velocity of the BIV ions measured approximately 2 cm inside the separatrix is small (≤ 2 kms -1 ) and in the ion diamagnetic drift direction. However, at the L → H-Mode transition it changes sign and begins to increase on the time-scale of the edge pressure gradients reaching the highest values at the end of the H * -phase. From these high perpendicular drift velocities it is infered that, in the H-mode, there exists a strong negative radial electric field (vertical strokeE τ vertical stroke ≤ kVm -1 ) just inside the separatrix. The dependence of the drift velocity of the BIV ions and E Τ on the NBI-heating power and the magnitude and direction of the plasma current and the magnetic field is investigated. (orig.)

Dinamizando el proceso de enseñanzaaprendizaje de la química. Las demostraciones químicas como una opción para cambiar la forma tradicional de enseñar química

Directory of Open Access Journals (Sweden)

Manuel Molina Caballero

2009-10-01

Full Text Available Creemos que la “quimifobia” que existe a nivel social está generada en buena medida por la forma cómo se realiza la enseñanza de la química en las aulas. Para generar un cambio en las metodologías habituales proponemos, en este trabajo, el uso de las demostraciones químicas, mostrando un ejemplo a partir de la descomposición del peróxido de hidrógeno, buscando la forma de incorporar las demostraciones en el aula y considerando su carácter atractivo, la participación del estudiante, su vínculo conceptual y las cuestiones de seguridad a tener en cuenta. Dejamos a los profesores la propuesta, esperando que con su ayuda quizá podamos dar un toque especial a la enseñanza de la química.

Measurement of quasi-static and low frequency electric fields on the Viking satellite

International Nuclear Information System (INIS)

Block, L.P.; Faelthammar, C.G.; Lindqvist, P.A.; Marklund, G.T.; Mozer, F.S.; Pedersen, A.

1987-03-01

The instrument for measurement of quasi-static and low frequency (dc and slow varying) electric fields on the Viking satellite is described. The instrument uses three spherical probe pairs to measure the full three-dimensional electric field vector with 18.75 ms time resolution. The probes are kept near plasma potential by means of a controllable bias current. A guard covering part of the booms is biased to a negative voltage to prevent photoelectrons escaping from the probes from reaching the satellite body. Current-voltage sweeps are performed to determine the plasma density and temperature and to select the optimal bias current. The bias currents to the probes and the voltage offset on the guards as well as the current-voltage sweeps are controlled by an on-board microprocessor which can be programmed from the ground and allows great flexibility. (authors)

Acousto-electrical speckle pattern in Lorentz force electrical impedance tomography

International Nuclear Information System (INIS)

Grasland-Mongrain, Pol; Destrempes, François; Cloutier, Guy; Mari, Jean-Martial; Souchon, Rémi; Catheline, Stefan; Chapelon, Jean-Yves; Lafon, Cyril

2015-01-01

Ultrasound speckle is a granular texture pattern appearing in ultrasound imaging. It can be used to distinguish tissues and identify pathologies. Lorentz force electrical impedance tomography is an ultrasound-based medical imaging technique of the tissue electrical conductivity. It is based on the application of an ultrasound wave in a medium placed in a magnetic field and on the measurement of the induced electric current due to Lorentz force. Similarly to ultrasound imaging, we hypothesized that a speckle could be observed with Lorentz force electrical impedance tomography imaging. In this study, we first assessed the theoretical similarity between the measured signals in Lorentz force electrical impedance tomography and in ultrasound imaging modalities. We then compared experimentally the signal measured in both methods using an acoustic and electrical impedance interface. Finally, a bovine muscle sample was imaged using the two methods. Similar speckle patterns were observed. This indicates the existence of an ‘acousto-electrical speckle’ in the Lorentz force electrical impedance tomography with spatial characteristics driven by the acoustic parameters but due to electrical impedance inhomogeneities instead of acoustic ones as is the case of ultrasound imaging. (paper)

Acousto-electrical speckle pattern in Lorentz force electrical impedance tomography

Science.gov (United States)

Grasland-Mongrain, Pol; Destrempes, François; Mari, Jean-Martial; Souchon, Rémi; Catheline, Stefan; Chapelon, Jean-Yves; Lafon, Cyril; Cloutier, Guy

2015-05-01

Ultrasound speckle is a granular texture pattern appearing in ultrasound imaging. It can be used to distinguish tissues and identify pathologies. Lorentz force electrical impedance tomography is an ultrasound-based medical imaging technique of the tissue electrical conductivity. It is based on the application of an ultrasound wave in a medium placed in a magnetic field and on the measurement of the induced electric current due to Lorentz force. Similarly to ultrasound imaging, we hypothesized that a speckle could be observed with Lorentz force electrical impedance tomography imaging. In this study, we first assessed the theoretical similarity between the measured signals in Lorentz force electrical impedance tomography and in ultrasound imaging modalities. We then compared experimentally the signal measured in both methods using an acoustic and electrical impedance interface. Finally, a bovine muscle sample was imaged using the two methods. Similar speckle patterns were observed. This indicates the existence of an ‘acousto-electrical speckle’ in the Lorentz force electrical impedance tomography with spatial characteristics driven by the acoustic parameters but due to electrical impedance inhomogeneities instead of acoustic ones as is the case of ultrasound imaging.

Risk analysis and detection of thrombosis by measurement of electrical resistivity of blood.

Science.gov (United States)

Sapkota, Achyut; Asakura, Yuta; Maruyama, Osamu; Kosaka, Ryo; Yamane, Takashi; Takei, Masahiro

2013-01-01

Monitoring of thrombogenic process is very important in ventricular assistance devices (VADs) used as temporary or permanent measures in patients with advanced heart failure. Currently, there is a lack of a system which can perform a real-time monitoring of thrombogenic activity. Electrical signals vary according to the change in concentration of coagulation factors as well as the distribution of blood cells, and thus have potential to detect the thrombogenic process in an early stage. In the present work, we have made an assessment of an instrumentation system exploiting the electrical properties of blood. The experiments were conducted using bovine blood. Electrical resistance tomography with eight-electrode sensor was used to monitor the spatio-temporal change in electrical resistivity of blood in thrombogenic and non-thrombogenic condition. Under non-thrombogenic condition, the resistivity was uniform across the cross-section and average resistivity monotonically decreased with time before remaining almost flat. In contrary, under thrombogenic condition, there was non-uniform distribution across the cross-section, and average resistivity fluctuated with time.

Measurement of ac electrical characteristics of SSC dipole magnets at Brookhaven

International Nuclear Information System (INIS)

Smedley, K.

1992-04-01

The SSC collider is designed to have circumference of 87 km. The superconducting magnets along the collider ring are grouped into ten sectors. Each sector, a string of average length of 8.7 km,m is powered by one power source located near the center of the sector. Because of the alternating-current (ac) electrical characteristics of the magnets, the power supply ripple currents and transients form a time and space distribution in the magnet string which affects particle motions. Additionally, since the power supply load is a magnet string, the current regulation loop design is highly dependent upon the ac electrical characteristics of the magnets. A means is needed to accurately determine the ac electrical characteristics of the superconducting magnets. The ac characteristics of magnets will be used to predict the ripple distribution of the long string of superconducting magnets. Magnet ac characteristics can also provide necessary information for the regulation loop design. This paper presents a method for measuring the ac characteristics of superconducting magnets. Two collider dipole magnets, one superconducting and one at room temperature, were tested at Brookhaven National Lab

Measurement of permanent electric dipole moments of charged hadrons in storage rings

Energy Technology Data Exchange (ETDEWEB)

Pretz, Joerg, E-mail: pretz@physik.rwth-aachen.de [III. Physikalisches Institut (Germany); Collaboration: JEDI Collaboration

2013-03-15

Permanent Electric Dipole Moments (EDMs) of elementary particles violate two fundamental symmetries: time reversal invariance ( T ) and parity ( P ). Assuming the CPT theorem this implies CP violation. The CP violation of the Standard Model is orders of magnitude too small to be observed experimentally in EDMs in the foreseeable future. It is also way too small to explain the asymmetry in abundance of matter and anti-matter in our universe. Hence, other mechanisms of CP violation outside the realm of the Standard Model are searched for and could result in measurable EDMs. Up to now most of the EDM measurements were done with neutral particles. With new techniques it is now possible to perform dedicated EDM experiments with charged hadrons at storage rings where polarized particles are exposed to an electric field. If an EDM exists the spin vector will experience a torque resulting in change of the original spin direction which can be determined with the help of a polarimeter. Although the principle of the measurement is simple, the smallness of the expected effect makes this a challenging experiment requiring new developments in various experimental areas. Complementary efforts to measure EDMs of proton, deuteron and light nuclei are pursued at Brookhaven National Laboratory and at Forschungszentrum Juelich with an ultimate goal to reach a sensitivity of 10{sup - 29}e{center_dot}cm.

La imagen pública de la química y su relación con la generación de actitudes hacia la química y su aprendizaje

Directory of Open Access Journals (Sweden)

William Manuel Mora Penagos

2012-04-01

Full Text Available El presente ensayo muestra cómo la imagen popular y escolar de la química se caracteriza por ser negativa, lo que viene incidiendo en la generación de actitudes negativas hacia esta ciencia y su aprendizaje. Las inadecuadas formas de comunicación del conocimiento de la química que se muestran en el cine, la TV y las revistas de ciencia popular, la visión irreconciliable entre ciencia y religión, y la poca claridad de las formas de producción del conocimiento químico mostradas en las aulas de clase, aparecen como las principales causas de esta situación. Superar esta imagen implica reconciliar la visión científica con la visión social de la química, por lo que el conocimiento en epistemología e historia de la química y la línea de investigación conocida como Public Understanding of Science desde el enfoque Ciencia/Tecnología/ Sociedad y Ambiente (CTS-A, son fundamentales para una didáctica de la química orientada hacia la alfabetización en química y a la formación docentes en torno al diseño curricular y la enseñanza de contenidos articulados a la generación de actitudes hacia el impacto social y ambiental de la química.

Rocket measurements of electric fields, electron density and temperature during the three phases of auroral substorms

International Nuclear Information System (INIS)

Marklund, G.; Block, L.; Lindqvist, P.-A.

1979-12-01

On Jan. 27, 1979, three rocket payloads were launched from Kiruna, Sweden, into different phases of two successive auroral substorms. Among other experiments, the payloads carried the RIT double probe electric field experiments, providing electric field, electron density and temperature data, which are presented here. These are discussed in association with observations of particles, ionospheric drifts (STARE) and electric fields in the equatorial plane (GEOS). The motions of the auroral forms, as obtained from auroral pictures are compared with the E x B/B 2 drifts and the currents calculated from the rocket electric field and density measurements with the equivalent current system deduced from ground based magnetometer data (SMA). (Auth.)

A corotation electric field model of the Earth derived from Swarm satellite magnetic field measurements

Science.gov (United States)

Maus, Stefan

2017-08-01

Rotation of the Earth in its own geomagnetic field sets up a primary corotation electric field, compensated by a secondary electric field of induced electrical charges. For the geomagnetic field measured by the Swarm constellation of satellites, a derivation of the global corotation electric field inside and outside of the corotation region is provided here, in both inertial and corotating reference frames. The Earth is assumed an electrical conductor, the lower atmosphere an insulator, followed by the corotating ionospheric E region again as a conductor. Outside of the Earth's core, the induced charge is immediately accessible from the spherical harmonic Gauss coefficients of the geomagnetic field. The charge density is positive at high northern and southern latitudes, negative at midlatitudes, and increases strongly toward the Earth's center. Small vertical electric fields of about 0.3 mV/m in the insulating atmospheric gap are caused by the corotation charges located in the ionosphere above and the Earth below. The corotation charges also flow outward into the region of closed magnetic field lines, forcing the plasmasphere to corotate. The electric field of the corotation charges further extends outside of the corotating regions, contributing radial outward electric fields of about 10 mV/m in the northern and southern polar caps. Depending on how the magnetosphere responds to these fields, the Earth may carry a net electric charge.

10 CFR 500.3 - Electric regions-electric region groupings for reliability measurements under the Powerplant and...

Science.gov (United States)

2010-01-01

... System (APS)—7, except Duquesne Light Company. 2. American Electric Power System (AEP)—entire AEP System... 10 Energy 4 2010-01-01 2010-01-01 false Electric regions-electric region groupings for reliability... of electric regions for use with regard to the Act. The regions are identified by FERC Power Supply...

Ionization measurement as a function of the electric field in tetramethyl-silane (TMS)

International Nuclear Information System (INIS)

Daba, A.G.

1992-07-01

The WALIC collaboration has built a calorimeter prototype using the tetramethyl-pentane (TMP) as active medium and lead as absorber medium in order to study the response of electrons and hadrons. The aim of this work is to study the response of tetramethyl-silane to high electric fields knowing that TMP and TMS have similar properties and similar behaviour with electric field. A test bench is mounted to measure the charge deposited by electrons emitted by a ruthenium source. The trigger was made using a silicon detector. Low noise amplifiers were designed and built for the signal conditioning and in order to reduce the pick-up noise, the system is completely isolated in a double Faraday cage. A theoretical study of noise has been developed. The signal allowed to study the behaviour of warm liquid in presence of a high electric field

Electrical conduction through surface superstructures measured by microscopic four-point probes

DEFF Research Database (Denmark)

Hasegawa, S.; Shiraki, I.; Tanabe, F.

2003-01-01

For in-situ measurements of the local electrical conductivity of well-defined crystal surfaces in ultra-high vacuum, we have developed two kinds of microscopic four-point probe methods. One involves a "four-tip STM prober," in which four independently driven tips of a scanning tunneling microscope...... (STM) are used for measurements of four-point probe conductivity. The probe spacing can be changed from 500 nm to 1 mm. The other method involves monolithic micro-four-point probes, fabricated on silicon chips, whose probe spacing is fixed around several mum. These probes are installed in scanning...

Evaluating groundwater flow using passive electrical measurements

Science.gov (United States)

Voytek, E.; Revil, A.; Singha, K.

2016-12-01

Accurate quantification of groundwater flow patterns, both in magnitude and direction, is a necessary component of evaluating any hydrologic system. Groundwater flow patterns are often determined using a dense network of wells or piezometers, which can be limited due to logistical or regulatory constraints. The self-potential (SP) method, a passive geophysical technique that relies on currents generated by water movement through porous materials, is a re-emerging alternative or addition to traditional piezometer networks. Naturally generated currents can be measured as voltage differences at the ground surface using only two electrodes, or a more complex electrode array. While the association between SP measurements and groundwater flow was observed as early as 1890s, the method has seen resurgence in hydrology since the governing equations were refined in the 1980s. The method can be used to analyze hydrologic processes at various temporal and spatial scales. Here we present the results of multiple SP surveys collected a multiple scales (1 to 10s of meters). Here single SP grid surveys are used to evaluate flow patterns through artic hillslopes at a discrete point in time. Additionally, a coupled groundwater and electrical model is used to analyze multiple SP data sets to evaluate seasonal changes in groundwater flow through an alpine meadow.

Simultaneous measurement of temperature, stress, and electric field in GaN HEMTs with micro-Raman spectroscopy.

Science.gov (United States)

Bagnall, Kevin R; Moore, Elizabeth A; Badescu, Stefan C; Zhang, Lenan; Wang, Evelyn N

2017-11-01

As semiconductor devices based on silicon reach their intrinsic material limits, compound semiconductors, such as gallium nitride (GaN), are gaining increasing interest for high performance, solid-state transistor applications. Unfortunately, higher voltage, current, and/or power levels in GaN high electron mobility transistors (HEMTs) often result in elevated device temperatures, degraded performance, and shorter lifetimes. Although micro-Raman spectroscopy has become one of the most popular techniques for measuring localized temperature rise in GaN HEMTs for reliability assessment, decoupling the effects of temperature, mechanical stress, and electric field on the optical phonon frequencies measured by micro-Raman spectroscopy is challenging. In this work, we demonstrate the simultaneous measurement of temperature rise, inverse piezoelectric stress, thermoelastic stress, and vertical electric field via micro-Raman spectroscopy from the shifts of the E 2 (high), A 1 longitudinal optical (LO), and E 2 (low) optical phonon frequencies in wurtzite GaN. We also validate experimentally that the pinched OFF state as the unpowered reference accurately measures the temperature rise by removing the effect of the vertical electric field on the Raman spectrum and that the vertical electric field is approximately the same whether the channel is open or closed. Our experimental results are in good quantitative agreement with a 3D electro-thermo-mechanical model of the HEMT we tested and indicate that the GaN buffer acts as a semi-insulating, p-type material due to the presence of deep acceptors in the lower half of the bandgap. This implementation of micro-Raman spectroscopy offers an exciting opportunity to simultaneously probe thermal, mechanical, and electrical phenomena in semiconductor devices under bias, providing unique insight into the complex physics that describes device behavior and reliability. Although GaN HEMTs have been specifically used in this study to

Simultaneous measurement of temperature, stress, and electric field in GaN HEMTs with micro-Raman spectroscopy

Science.gov (United States)

Bagnall, Kevin R.; Moore, Elizabeth A.; Badescu, Stefan C.; Zhang, Lenan; Wang, Evelyn N.

2017-11-01

As semiconductor devices based on silicon reach their intrinsic material limits, compound semiconductors, such as gallium nitride (GaN), are gaining increasing interest for high performance, solid-state transistor applications. Unfortunately, higher voltage, current, and/or power levels in GaN high electron mobility transistors (HEMTs) often result in elevated device temperatures, degraded performance, and shorter lifetimes. Although micro-Raman spectroscopy has become one of the most popular techniques for measuring localized temperature rise in GaN HEMTs for reliability assessment, decoupling the effects of temperature, mechanical stress, and electric field on the optical phonon frequencies measured by micro-Raman spectroscopy is challenging. In this work, we demonstrate the simultaneous measurement of temperature rise, inverse piezoelectric stress, thermoelastic stress, and vertical electric field via micro-Raman spectroscopy from the shifts of the E2 (high), A1 longitudinal optical (LO), and E2 (low) optical phonon frequencies in wurtzite GaN. We also validate experimentally that the pinched OFF state as the unpowered reference accurately measures the temperature rise by removing the effect of the vertical electric field on the Raman spectrum and that the vertical electric field is approximately the same whether the channel is open or closed. Our experimental results are in good quantitative agreement with a 3D electro-thermo-mechanical model of the HEMT we tested and indicate that the GaN buffer acts as a semi-insulating, p-type material due to the presence of deep acceptors in the lower half of the bandgap. This implementation of micro-Raman spectroscopy offers an exciting opportunity to simultaneously probe thermal, mechanical, and electrical phenomena in semiconductor devices under bias, providing unique insight into the complex physics that describes device behavior and reliability. Although GaN HEMTs have been specifically used in this study to

Cuscutaceae endémicas del Perú

Directory of Open Access Journals (Sweden)

Blanca León

2013-10-01

Full Text Available La familia Cuscutaceae es reconocida en el Perú por presentar un género, Cuscuta, y 19 especies (Brako & Zarucchi, 1993, todas ellas hierbas. En este trabajo reconocemos siete especies endémicas, aunque en necesidad de revisión taxonómica y colecciones botánicas; por ello no se aplicaron las categorías y criterios de la UICN. Estos taxones endémicos ocupan principalmente la región Mesoandina, por debajo de los 3200 m de altitud. Aparentemente, sólo una de estas especies se encuentra representada dentro del Sistema Nacional de Áreas Naturales Protegidas por el Estado.

Dilleniaceae endémicas del Perú

Directory of Open Access Journals (Sweden)

Blanca León

2013-10-01

Full Text Available La familia Dilleniaceae es una adición reciente a la flora endémica peruana; los endemismos han sido recolectados y reconocidos hacia fines de los 1990. Está representada en el Perú por seis géneros y 23 especies (Brako & Zarucchi, 1993; Ulloa Ulloa et al., 2004, la mayoría lianas. En este trabajo reconocemos tres endemismos en dos géneros. Las especies endémicas ocupan la región Bosques Húmedos Amazónicos, entre los 100 y 125 m de altitud. No se encuentra representada en el Sistema Nacional de Áreas Naturales Protegidas por el Estado.

Las cooperativas: Una alternativa económica y social frente a la crisis

Directory of Open Access Journals (Sweden)

Javier Divar Garteiz-Aurrecoa

2013-12-01

Full Text Available El Cooperativismo nació como alternativa económica y social, impulsado por la piedad religiosa y reglado bajo los principios democráticos. La solidaridad y la democracia económica hacen de las cooperativas  sociedades especialmente resistentes frente a las dificultades económicas.Recibido: 29.05.2013Aceptado: 26.06.2013

Microwave measurement of electrical fields in different media – principles, methods and instrumentation

International Nuclear Information System (INIS)

St. Kliment Ohridski, Faculty of Physics, James Bourchier blvd., Sofia 1164 (Bulgaria))" data-affiliation=" (Sofia University St. Kliment Ohridski, Faculty of Physics, James Bourchier blvd., Sofia 1164 (Bulgaria))" >Dankov, Plamen I

2014-01-01

This paper, presented in the frame of 4th International Workshop and Summer School on Plasma Physics (IWSSPP'2010, Kiten, Bulgaria), is a brief review of the principles, methods and instrumentation of the microwave measurements of electrical fields in different media. The main part of the paper is connected with the description of the basic features of many field sensors and antennas – narrow-, broadband and ultra-wide band, miniaturized, reconfigurable and active sensors, etc. The main features and applicability of these sensors for determination of electric fields in different media is discussed. The last part of the paper presents the basic principles for utilization of electromagnetic 3-D simulators for E-field measurement purposes. Two illustrative examples have been given – the determination of the dielectric anisotropy of multi-layer materials and discussion of the selectivity of hairpin-probe for determination of the electron density in dense gaseous plasmas.

Electrical, Magnetic, and Optical Measurement Facility

Data.gov (United States)

Federal Laboratory Consortium — FUNCTION: Provides tools necessary for electrical, magnetic, and optical characterization of bulk and thin-film materials. This includes the ability to determine the...

Broadband measurements of high-frequency electric field levels and exposure ratios determination

Directory of Open Access Journals (Sweden)

Vulević Branislav

2017-01-01

Full Text Available The exposure of people to high-frequency electromagnetic fields (over 100 kHz that emanate from modern wireless information transmission systems is inevitable in modern times. Due to the rapid development of new technologies, measuring devices and their connection to measuring systems, the first fifteen years of the 21st century are characterized by the appearance of different approaches to measurements. This prompts the need for the assessment of the exposure of people to these fields. The main purpose of this paper is to show how to determine the exposure ratios based on the results of broadband measurements of the high-frequency electric field in the range of 3 MHz to 18 GHz in the environment.

Vapor cell geometry effect on Rydberg atom-based microwave electric field measurement

Science.gov (United States)

Zhang, Linjie; Liu, Jiasheng; Jia, Yue; Zhang, Hao; Song, Zhenfei; Jia, Suotang

2018-03-01

The geometry effect of a vapor cell on the metrology of a microwave electric field is investigated. Based on the splitting of the electromagnetically induced transparency spectra of cesium Rydberg atoms in a vapor cell, high-resolution spatial distribution of the microwave electric field strength is achieved for both a cubic cell and a cylinder cell. The spatial distribution of the microwave field strength in two dimensions is measured with sub-wavelength resolution. The experimental results show that the shape of a vapor cell has a significant influence on the abnormal spatial distribution because of the Fabry–Pérot effect inside a vapor cell. A theoretical simulation is obtained for different vapor cell wall thicknesses and shows that a restricted wall thickness results in a measurement fluctuation smaller than 3% at the center of the vapor cell. Project supported by the National Key Research and Development Program of China (Grant Nos. 2017YFA03044200 and 2016YFF0200104), the National Natural Science Foundation of China (Grant Nos. 91536110, 61505099, and 61378013), and the Fund for Shanxi “331 Project” Key Subjects Construction, China.

Modelling of Lunar Dust and Electrical Field for Future Lunar Surface Measurements

Science.gov (United States)

Lin, Yunlong

Modelling of the lunar dust and electrical field is important to future human and robotic activities on the surface of the moon. Apollo astronauts had witnessed the maintaining of micron- and millimeter sized moon dust up to meters level while walked on the surface of the moon. The characterizations of the moon dust would enhance not only the scientific understanding of the history of the moon but also the future technology development for the surface operations on the moon. It has been proposed that the maintaining and/or settlement of the small-sized dry dust are related to the size and weight of the dust particles, the level of the surface electrical fields on the moon, and the impaction and interaction between lunar regolith and the solar particles. The moon dust distributions and settlements obviously affected the safety of long term operations of future lunar facilities. For the modelling of the lunar dust and the electrical field, we analyzed the imaging of the legs of the moon lander, the cover and the footwear of the space suits, and the envelope of the lunar mobiles, and estimated the size and charges associated with the small moon dust particles, the gravity and charging effects to them along with the lunar surface environment. We also did numerical simulation of the surface electrical fields due to the impaction of the solar winds in several conditions. The results showed that the maintaining of meters height of the micron size of moon dust is well related to the electrical field and the solar angle variations, as expected. These results could be verified and validated through future on site and/or remote sensing measurements and observations of the moon dust and the surface electrical field.

Polynomial Collocation for Handling an Inaccurately Known Measurement Configuration in Electrical Impedance Tomography

DEFF Research Database (Denmark)

Hyvönen, Niina; Kaarnioja, V.; Mustonen, L.

2017-01-01

The objective of electrical impedance tomography is to reconstruct the internal conductivity of a physical body based on measurements of current and potential at a finite number of electrodes attached to its boundary. Although the conductivity is the quantity of main interest in impedance...... tomography, a real-world measurement configuration includes other unknown parameters as well: The information on the contact resistances, electrode positions, and body shape is almost always incomplete. In this work, the dependence of the electrode measurements on all aforementioned model properties...

Preliminary Findings from the One-Year Electric Field Study in the North Slope of Alaska (OYES-NSA), Atmospheric Radiation Measurement (ARM) Field Campaign

Science.gov (United States)

Lavigne, T.; Liu, C.

2017-12-01

Previous studies focusing on the comparison of the measured electric field to the physical properties of global electrified clouds have been conducted almost exclusively in the Southern Hemisphere. The One-Year Electric Field Study-North Slope of Alaska (OYES-NSA) aims to establish a long-running collection of this valuable electric field data in the Northern Hemisphere. Presented here is the six-month preliminary data and results of the OYES-NSA Atmospheric Radiation Mission (ARM) field campaign. The local electric field measured in Barrow, Alaska using two CS110 reciprocating shutter field meters, has been compared to simultaneous measurements from the ARM Ka-Band zenith radar, to better understand the influence and contribution of different types of clouds on the local electric field. The fair-weather electric field measured in Barrow has also been analyzed and compared to the climatology of electric field at Vostok Station, Antarctica. The combination of the electric field dataset in the Northern Hemisphere, alongside the local Ka cloud radar, global Precipitation Feature (PF) database, and quasi-global lightning activity (55oN-55oS), allows for advances in the physical understanding of the local electric field, as well as the Global Electric Circuit (GEC).

Principios de laboratorio y aplicaciones en la práctica clínica de las técnicas moleculares, genómicas y proteómicas

Directory of Open Access Journals (Sweden)

Jenny Hernández Betancourt

2014-10-01

Full Text Available La heterogénea expresión clínica de las enfermedades, la necesidad de la interpretación de los procesos fisiológicos y fisiopatológicos, así como la búsqueda incesante de nuevas estrategias diagnósticas y terapéuticas, han conducido al desarrollo de las biociencias, en particular de la genética, la genómica, la biología molecular y las tecnologías asociadas. Han emergido en los últimos años disciplinas como la trascriptómica, la epigenómica, la proteómica y la metabolómica, cada una con un objeto de estudio determinado, que deriva de los tipos moleculares específicos y sus relaciones y todas con aplicaciones potenciales dentro de una nueva medicina con un enfoque personalizado. Hoy se dispone de técnicas moleculares que se basan en la hibridación de ácidos nucleicos, tanto in situ como el dot-blot, el Southern blot y el Northern blot. Otros métodos requieren la amplificación del ADN, como la reacción en cadena de la polimerasa, los microarreglos y la secuenciación. La proteómica se perfila como una potente herramienta para el estudio de aspectos fisiológicos y patológicos del ser humano; sus técnicas incluyen la electroforesis bidimensional, la espectrometría de masas y las micromatrices de proteínas. La búsqueda activa de biomarcadores a partir de casi todos los líquidos biológicos y tejidos de varias naturalezas es una de las principales aplicaciones de la proteómica. Es importante atender, comprender e introducir estos nuevos métodos en la práctica clínica por sus potencialidades para el diagnóstico, el desarrollo de estrategias terapéuticas, la predicción y estratificación de riesgo, de la resistencia al tratamiento y las posibilidades de supervivencia

Sobre la termodinámica de las soluciones electrolíticas

Directory of Open Access Journals (Sweden)

Wilmar Osorio Viana

2007-01-01

Full Text Available Se presentan los elementos teóricos básicos de la fisicoquímica de las soluciones electrolíticas, buscando una conexión entre los aspectos moleculares característicos y el desarrollo de modelos termodinámicos semiempíricos apropiados para el cálculo de propiedades. Se presenta una visión general del desarrollo histórico de modelos para soluciones electrolíticas y se adoptan los modelos de Debye-Hückel y NRTL-E para describir cualitativa y cuantitativamente, mediante experimentación virtual, el desempeño de sistemas binarios solvente-electrólito inorgánico. Se aborda el problema de las soluciones multielectrolíticas, describiendo las características fundamentales del modelo del enfoque unificado, el cual se acopla al modelo NRTL-E, permitiendo generalizar el tratamiento sin la inclusión de parámetros empíricos adicionales y con interesantes aportes al entendimiento teórico.

Funciones Económicas en un Entorno Incierto

OpenAIRE

Lazzari, Luisa L; Chiodi, Jorge A; Moulia, Patricia I

2015-01-01

El mundo está atravesando una de las crisis económicas más profundas de los últimos tiempos. Los escenarios actuales y futuros están plagados de incertidumbre que, en general, no se considera en el análisis de las distintas funciones económicas de interés para el desarrollo del negocio, y la realidad se representa mediante modelos estáticos y casi perfectos del comportamiento de los mercados. La teoría de conjuntos borrosos permite construir modelos adecuados a partir de realidades inciertas ...

Measurement of AC electrical characteristics of SSC superconducting dipole magnets

International Nuclear Information System (INIS)

Smedley, K.M.; Shafer, R.E.

1992-01-01

Experiments were conducted to measure the AC electrical characteristics of SSC superconducting dipole magnets over the frequency range of 0.1 Hz to 10 kHz. A magnet equivalent circuit representing the magnet DC inductance, eddy current losses, coil-to-ground and turn-to-turn capacitance, was synthesized from the experimental data. This magnet equivalent circuit can be used to predict the current ripple distribution along the superconducting magnet string and can provide dynamic information for the design of the collider current regulation loop

Electrical breakdown studies with Mycalex insulators

International Nuclear Information System (INIS)

Waldron, W.; Greenway, W.; Eylon, S.; Henestroza, E.; Yu, S.

2003-01-01

Insulating materials such as alumina and glass-bonded mica (Mycalex) are used in accelerator systems for high voltage feedthroughs, structural supports, and barriers between high voltage insulating oil and the vacuum beam pipe in induction accelerator cells. Electric fields in the triple points should be minimized to prevent voltage breakdown. Mechanical stress can compromise seals and result in oil contamination of the insulator surface. We have tested various insulator cleaning procedures including ultrasonic cleaning with a variety of aqueous-based detergents, and manual scrubbing with various detergents. Water sheeting tests were used to determine the initial results of the cleaning methods. Ultimately, voltage breakdown tests will be used to quantify the benefits of these cleaning procedures

CD56+ immune cell infiltration and MICA are decreased in breast lobules with fibrocystic changes.

Science.gov (United States)

Kerekes, Daniel; Visscher, Daniel W; Hoskin, Tanya L; Radisky, Derek C; Brahmbhatt, Rushin D; Pena, Alvaro; Frost, Marlene H; Arshad, Muhammad; Stallings-Mann, Melody; Winham, Stacey J; Murphy, Linda; Denison, Lori; Carter, Jodi M; Knutson, Keith L; Degnim, Amy C

2018-02-01

While the role of natural killer (NK) cells in breast cancer therapy has been investigated, little information is known about NK cell function and presence in nonmalignant and premalignant breast tissue. Here, we investigate and quantify NK cell marker CD56 and activating ligand MICA in breast tissue with benign breast disease. Serial tissue sections from 88 subjects, 44 with benign breast disease (BBD) who remained cancer-free, and 44 with BBD who later developed cancer, were stained with H&E, anti-MICA, and anti-CD56. Up to ten representative lobules were identified on each section. Using digital image analysis, MICA and CD56 densities were determined for each lobule, reported as percent of pixels in the lobule that registered as stained by each antibody. Analyses were performed on a per-subject and per-lobule basis. Per-subject multivariate analyses showed associations of CD56 and MICA with age: CD56 was increased in older subjects (p = 0.03), while MICA was increased in younger subjects (p = 0.005). Per-lobule analyses showed that CD56 and MICA levels were both decreased in lobules with fibrocystic change, with median levels of CD56 and MICA staining, respectively, at 0.31 and 7.0% in fibrocystic lobules compared to 0.76 and 12.2% in lobules without fibrocystic change (p fibrocystic lobules, proliferative/atypical lobules showed significantly lower expression compared to nonproliferative lobules for MICA (p = 0.02) but not for CD56 (p = 0.80). Levels of CD56+ NK cells and activating ligand MICA were decreased in breast lobules with fibrocystic change, and MICA levels showed a significant stepwise decrease with increasing histopathologic abnormality. MICA levels were also significantly decreased in older subjects, who generally have higher risk of developing cancer. These findings advance a model in which MICA promotes cytotoxic activity in CD56+ NK cells to protect against tumorigenesis in breast lobules, and suggest further research is warranted.

Influencia de la autoeficacia académica y la procrastinación académica sobre el cansancio emocional de estudiantes de la Universidad Alas Peruanas, Lima, 2015

OpenAIRE

Gutiérrez Torres, Andrés Martín

2015-01-01

Objetivo: determinar cuánta es la influencia de la autoeficacia académica y la procrastinación académica sobre el cansancio emocional de estudiantes de la Universidad Alas Peruanas, Lima, 2015. Metodología: se usó un diseño observacional, transversal, retrospectivo y correlacional-causal. La muestra no probabilística fue de 332 estudiantes de Psicología de una universidad privada de Lima, quienes fueron evaluados con tres instrumentos: Escala de Autoeficacia para Situaciones Académicas, E...

Electric-Field-Induced Superconductivity Detected by Magnetization Measurements of an Electric-Double-Layer Capacitor

NARCIS (Netherlands)

Kasahara, Yuichi; Nishijima, Takahiro; Sato, Tatsuya; Takeuchi, Yuki; Ye, Jianting; Yuan, Hongtao; Shimotani, Hidekazu; Iwasa, Yoshihiro

We report evidence for superconductivity induced by the application of strong electric fields onto the surface of a band insulator, ZrNCl, provided by the observation of a shielding diamagnetic signal. We introduced an electric-double-layer capacitor configuration and in situ magnetization