WorldWideScience

Sample records for mhz bandpass sigma

  1. Superconducting bandpass delta-sigma modulator

    International Nuclear Information System (INIS)

    Bulzacchelli, J.F.; Lee, H.-S.; Misewich, J.A.; Ketchen, M.B.

    1999-01-01

    Bandpass delta-sigma modulators digitize narrowband signals with high dynamic range and linearity. The required sampling rate is only a few times higher than the centre frequency of the input. This paper presents a superconducting bandpass delta-sigma modulator for direct analogue-to-digital conversion of RF signals in the GHz range. The input signal is capacitively coupled to one end of a microstrip transmission line, and a single flux quantum balanced comparator quantizes the current flowing out of the other end. Quantization noise is suppressed at the quarter-wave resonance of the transmission line (about 2 GHz in our design). Circuit performance at a 20 GHz sampling rate has been studied with several long JSIM simulations. Full-scale (FS) input sensitivity is 20 mV (rms), and in-band noise is -53 dBFS and -57 dBFS over bandwidths of 39 MHz and 19.5 MHz, respectively. In-band intermodulation distortion is better than -69 dBFS. (author)

  2. Design and implementation of quadrature bandpass sigma-delta modulator used in low-IF RF receiver

    Science.gov (United States)

    Ge, Binjie; Li, Yan; Yu, Hang; Feng, Xiaoxing

    2018-05-01

    This paper presents the design and implementation of quadrature bandpass sigma-delta modulator. A pole movement method for transforming real sigma-delta modulator to a quadrature one is proposed by detailed study of the relationship of noise-shaping center frequency and integrator pole position in sigma-delta modulator. The proposed modulator uses sampling capacitor sharing switched capacitor integrator, and achieves a very small feedback coefficient by a series capacitor network, and those two techniques can dramatically reduce capacitor area. Quantizer output-dependent dummy capacitor load for reference voltage buffer can compensate signal-dependent noise that is caused by load variation. This paper designs a quadrature bandpass Sigma-Delta modulator for 2.4 GHz low IF receivers that achieve 69 dB SNDR at 1 MHz BW and -1 MHz IF with 48 MHz clock. The chip is fabricated with SMIC 0.18 μm CMOS technology, it achieves a total power current of 2.1 mA, and the chip area is 0.48 mm2. Project supported by the National Natural Science Foundation of China (Nos. 61471245, U1201256), the Guangdong Province Foundation (No. 2014B090901031), and the Shenzhen Foundation (Nos. JCYJ20160308095019383, JSGG20150529160945187).

  3. A sixth-order continuous-time bandpass sigma-delta modulator for digital radio IF

    NARCIS (Netherlands)

    Engelen, van J.A.E.P.; Plassche, van de R.J.; Stikvoort, E.F.; Venes, A.G.W.

    1999-01-01

    This paper presents a sixth-order continuous-time bandpass sigma-delta modulator (SDM) for analog-to-digital conversion of intermediate-frequency signals. An important aspect in the design of this SDM is the stability analysis using the describing function method. The key to the analysis is the

  4. A Signal-Interleaving Complex Bandpass Sigma-Delta Converter

    DEFF Research Database (Denmark)

    Wad, Paul Emmanuel

    1997-01-01

    Complex or quadrature Sigma-Delta converters operate on complex signals, i.e. signals consisting of a real and an imaginary component, whereas conventional converters operate only on real signals. The advantage of complex signal processing in the discrete-time domain is that the entire sampling...

  5. Segmented correlation measurements on superconducting bandpass delta-sigma modulator with and without input tone

    International Nuclear Information System (INIS)

    Bulzacchelli, John F; Lee, Hae-Seung; Hong, Merit Y; Misewich, James A; Ketchen, Mark B

    2003-01-01

    Segmented correlation is a useful technique for testing a superconducting analogue-to-digital converter, as it allows the output spectrum to be estimated with fine frequency resolution even when data record lengths are limited by small on-chip acquisition memories. Previously, we presented segmented correlation measurements on a superconducting bandpass delta-sigma modulator sampling at 40.2 GHz under idle channel (no input) conditions. This paper compares the modulator output spectra measured by segmented correlation with and without an input tone. Important practical considerations of calculating segmented correlations are discussed in detail. Resolution enhancement by segmented correlation does reduce the spectral width of the input tone in the desired manner, but the signal power due to the input increases the variance of the spectral estimate near the input frequency, hindering accurate calculation of the in-band noise. This increased variance, which is predicted by theory, must be considered carefully in the application of segmented correlation. Methods for obtaining more accurate estimates of the quantization noise spectrum which are closer to those measured with no input are described

  6. A 10 MHz Bandwidth Continuous-Time Delta-Sigma Modulator for Portable Ultrasound Scanners

    DEFF Research Database (Denmark)

    Llimos Muntal, Pere; Jørgensen, Ivan Harald Holger; Bruun, Erik

    2016-01-01

    comparator and a pull-down clocked latch. The feedback signal is generated with voltage DACs based on transmission gates. Using this implementation, a small and low-power solution required for portable ultrasound scanner applications is achieved. The modulator has a bandwidth of 10 MHz with an oversampling......A fourth-order 1-bit continuous-time delta-sigma modulator designed in a 65 nm process for portable ultrasound scanners is presented in this paper. The loop filter consists of RCintegrators, with programmable capacitor arrays and resistors, and the quantizer is implemented with a high-speed clocked...

  7. A 1 MHz BW 34.2 fJ/step Continuous Time Delta Sigma Modulator With an Integrated Mixer for Cardiac Ultrasound.

    Science.gov (United States)

    Kaald, Rune; Eggen, Trym; Ytterdal, Trond

    2017-02-01

    Fully digitized 2D ultrasound transducer arrays require one ADC per channel with a beamforming architecture consuming low power. We give design considerations for per-channel digitization and beamforming, and present the design and measurements of a continuous time delta-sigma modulator (CTDSM) for cardiac ultrasound applications. By integrating a mixer into the modulator frontend, the phase and frequency of the input signal can be shifted, thereby enabling both improved conversion efficiency and narrowband beamforming. To minimize the power consumption, we propose an optimization methodology using a simulated annealing framework combined with a C++ simulator solving linear electrical networks. The 3rd order single-bit feedback type modulator, implemented in a 65 nm CMOS process, achieves an SNR/SNDR of 67.8/67.4 dB across 1 MHz bandwidth consuming 131 [Formula: see text] of power. The achieved figure of merit of 34.2 fJ/step is comparable with state-of-the-art feedforward type multi-bit designs. We further demonstrate the influence to the dynamic range when performing dynamic receive beamforming on recorded delta-sigma modulated bit-stream sequences.

  8. Compact microstrip bandpass filter with tunable notch

    DEFF Research Database (Denmark)

    Christensen, Silas; Zhurbenko, Vitaliy; Johansen, Tom Keinicke

    2014-01-01

    Two different designs combining a bandpass and a notch filter are developed to operate in the receiving band from 350–470 MHz. The bandpass filter is designed from a simple structure, by use of only four short circuited stubs and a half wavelength transmission line connecting the stubs. The tunable...... notch filter ensures an attenuation level of 19.3 dB to 27.3 dB in the frequency range from 360–480 MHz. The measured passband ripple of the combined filter is less than 0.5 dB, while the insertion loss for the simplest design is less than 1.7 dB only 10 MHz from the notch frequency. Even though...... the wavelength on the selected substrate (εr = 3.55) is approximately 45 cm, the outer dimensions of the final filter only measure 10×10 cm2....

  9. Some arithmetically symmetrical bandpass filters

    Science.gov (United States)

    Paranasi, P.; Roy, S. C. D.

    1981-01-01

    A combination of the conventional and Matthaei lowpass-bandpass transformations is shown to result in some bandpass filters having very good arithmetic symmetry. The technique presented is applicable to the Butterworth and inverse Chebyshev types of magnitude approximations and the Bessel type of delay approximations. It is not valid, however, for the Chebyshev and elliptic varieties of filters.

  10. A Microwave Tunable Bandpass Filter for Liquid Crystal Applications

    Science.gov (United States)

    Cao, Weiping; Jiang, Di; Liu, Yupeng; Yang, Yuanwang; Gan, Baichuan

    2017-07-01

    In this paper, a novel microwave continuously tunable band-pass filter, based on nematic liquid crystals (LCs), is proposed. It uses liquid crystal (LC) as the electro-optic material to mainly realize frequency shift at microwave band by changing the dielectric anisotropy, when applying the bias voltage. According to simulation results, it achieves 840 MHz offset. Comparing to the existing tunable filter, it has many advantages, such as continuously tunable, miniaturization, low processing costs, low tuning voltage, etc. Thus, it has shown great potentials in frequency domain and practical applications in modern communication.

  11. UV Bandpass Optical Filter for Microspectometers

    NARCIS (Netherlands)

    Correia, J.H.; Emadi, A.R.; Wolffenbuttel, R.F.

    2006-01-01

    This paper describes the design and modeling of a UV bandpass optical filter for microspectrometers. The materials used for fabricating the multilayer UV filter are: silicon dioxide (SiO2), titanium dioxide (TiO2) and yttrium oxide (Y2O3). The optical filter shows a bandpass response wavelength in

  12. High Performance Miniature Bandpass Filters, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal is submitted for developing low impedance, miniature bandpass RF frequency filter via MEMS technique, in applications of SMAP, Aquarius follow-on,...

  13. 6 sigma quality performance

    International Nuclear Information System (INIS)

    Yu, Yeong Hak

    2000-03-01

    This deals with 6 sigma quality performance introducing company which has 6 sigma quality management, 6 sigma quality activity and customer, secret of success of 6 sigma quality management, what 6 sigma is, 6 sigma quality management propel system 5 propel steps of project like point of 6 sigma, flow of problem solution, tool for propel of project, performance of CTQ and total customer satisfaction, and quality management system and 6 sigma quality.

  14. The point of 6 sigma

    International Nuclear Information System (INIS)

    An, Yeong Jin

    2000-07-01

    This book gives descriptions of the point of 6 sigma. These are the titles of this : what 6 sigma is, sigma conception, motor roller 3.4 ppm, centering error, 6 sigma purpose, 6 sigma principle, eight steps of innovation strategy, 6 sigma innovation strategy of easy system step, measurement standard of 6 sigma outcome, the main role of 6 sigma, acknowledgment and reword, 6 sigma characteristic, 6 sigma effect, 6 sigma application and problems which happen when 6 sigma introduces.

  15. A Tunable Low Noise Active Bandpass Filter Using a Noise Canceling Technique

    OpenAIRE

    Soltani, N.

    2016-01-01

    A monolithic tunable low noise active bandpass filter is presented in this study. Biasing voltages can control the center frequency and quality factor. By keeping the gain constant, the center frequency shift is 300 MHz. The quality factor can range from 90 to 290 at the center frequency. By using a noise cancelling circuit, noise is kept lower than 2.8 dB. The proposed filter is designed using MMIC technology with a center frequency of 2.4 GHz and a power consumption of 180 mW. ED02AH techno...

  16. A Tunable Low Noise Active Bandpass Filter Using a Noise Canceling Technique

    Directory of Open Access Journals (Sweden)

    N. Soltani

    2016-12-01

    Full Text Available A monolithic tunable low noise active bandpass filter is presented in this study. Biasing voltages can control the center frequency and quality factor. By keeping the gain constant, the center frequency shift is 300 MHz. The quality factor can range from 90 to 290 at the center frequency. By using a noise cancelling circuit, noise is kept lower than 2.8 dB. The proposed filter is designed using MMIC technology with a center frequency of 2.4 GHz and a power consumption of 180 mW. ED02AH technology is used to simulate the circuit elements.

  17. Highly Tunable Narrow Bandpass MEMS Filter

    KAUST Repository

    Hafiz, Md Abdullah Al

    2017-07-07

    We demonstrate a proof-of-concept highly tunable narrow bandpass filter based on electrothermally and electrostatically actuated microelectromechanical-system (MEMS) resonators. The device consists of two mechanically uncoupled clamped-clamped arch resonators, designed such that their resonance frequencies are independently tuned to obtain the desired narrow passband. Through the electrothermal and electrostatic actuation, the stiffness of the structures is highly tunable. We experimentally demonstrate significant percentage tuning (~125%) of the filter center frequency by varying the applied electrothermal voltages to the resonating structures, while maintaining a narrow passband of 550 ± 50 Hz, a stopband rejection of >17 dB, and a passband ripple ≤ 2.5 dB. An analytical model based on the Euler-Bernoulli beam theory is used to confirm the behavior of the filter, and the origin of the high tunability using electrothermal actuation is discussed.

  18. Fabrication of Compact Microstrip Line-Based Balun-Bandpass Filter with High Common-Mode Suppression

    Directory of Open Access Journals (Sweden)

    Chia-Mao Chen

    2014-01-01

    Full Text Available A new type of balun-bandpass filter was proposed based on the traditional coupled-line theory and folded open-loop ring resonators (OLRRs configuration. For that, a new device with both filter-type and balun-type characteristics was investigated and fabricated. Both magnetic and electric coupling structures were implemented to provide high performance balun-bandpass responses. The fabricated balun-bandpass filters had a wide bandwidth more than 200 MHz and a low insertion loss less than 2.51 dB at a center frequency of 2.6 GHz. The differences between the two outputs were below 0.4 dB in magnitude and within 180 ± 7° in phase. Also, the balun-bandpass filter presented an excellent common-mode rejection ratio over 25 dB in the passband. An advanced design methodology had been adopted based on EM simulation for making these designed parameters of OLRRs, microstrip lines, and open stubs. The measured frequency responses agreed well with simulated ones.

  19. Topological massive sigma models

    International Nuclear Information System (INIS)

    Lambert, N.D.

    1995-01-01

    In this paper we construct topological sigma models which include a potential and are related to twisted massive supersymmetric sigma models. Contrary to a previous construction these models have no central charge and do not require the manifold to admit a Killing vector. We use the topological massive sigma model constructed here to simplify the calculation of the observables. Lastly it is noted that this model can be viewed as interpolating between topological massless sigma models and topological Landau-Ginzburg models. ((orig.))

  20. Understanding delta-sigma data converters

    CERN Document Server

    Pavan, Shanti; Temes, Gabor C

    2017-01-01

    This new edition introduces novel analysis and design techniques for delta-sigma (ΔΣ) converters in physical and conceptual terms, and includes new chapters that explore developments in the field over the last decade. This book explains the principles and operation of delta-sigma analog-to-digital converters (ADCs) in physical and conceptual terms in accordance with the most recent developments in the field. The interest of ΔΣ converter designers has shifted significantly over the past decade, due to many new applications for data converters at the far ends of the frequency spectrum. Continuous-time delta-sigma A/D converters with GHz clocks, of both lowpass and bandpass types, are required for wireless applications. At the other extreme, multiplexed ADCs with very narrow (sometimes 10 Hz wide) signal bandwidths, but very high accuracy are needed in the interfaces of biomedical and environmental sensors. To reflect the changing eeds of designers, the second edition includes significant new material on bo...

  1. SIGMA without effort

    International Nuclear Information System (INIS)

    Hagedorn, R.; Reinfelds, J.

    1978-01-01

    SIGMA (System for Interactive Graphical Analysis) is an interactive computing language with automatic array handling and graphical facilities. It is designed as a tool for mathematical problem solving. The SIGMA language is simple, almost obvious, yet flexible and powerful. This tutorial introduces the beginner to SIGMA. It is supposed to be used at a graphics terminal having access to SIGMA. The user will learn the language in dialogue with the system in sixteen sessions of about one hour. The first session enables him already to compute and display functions of one or two variables. (Auth.)

  2. Six Sigma software development

    CERN Document Server

    Tayntor, Christine B

    2002-01-01

    Since Six Sigma has had marked success in improving quality in other settings, and since the quality of software remains poor, it seems a natural evolution to apply the concepts and tools of Six Sigma to system development and the IT department. Until now however, there were no books available that applied these concepts to the system development process. Six Sigma Software Development fills this void and illustrates how Six Sigma concepts can be applied to all aspects of the evolving system development process. It includes the traditional waterfall model and in the support of legacy systems,

  3. Six Sigma in Education

    Science.gov (United States)

    LeMahieu, Paul G.; Nordstrum, Lee E.; Cudney, Elizabeth A.

    2017-01-01

    Purpose: This paper is one of seven in this volume that aims to elaborate different approaches to quality improvement in education. It delineates a methodology called Six Sigma. Design/methodology/approach: The paper presents the origins, theoretical foundations, core principles and a case study demonstrating an application of Six Sigma in a…

  4. Narrow Sigma -hypernuclear states

    CERN Document Server

    Gal, A

    1980-01-01

    It is shown that the spin-isospin dependence of low-energy Sigma N to Lambda N conversion leads to substantial quenching of nuclear-matter estimates of the widths of some Sigma -hypernuclear states produced in (K/sup -/, pi ) reactions, to a level below 10 MeV. The estimated widths compare favorably with those of the Sigma -hypernuclear peaks recently observed at CERN for /sup 7/Li, /sup 9/Be, and /sup 12/C. Tentative quantum number assignments are suggested for these states. (10 refs).

  5. HTS dual-band bandpass filters using stub-loaded hair-pin resonators for mobile communication systems

    Energy Technology Data Exchange (ETDEWEB)

    Sekiya, N., E-mail: nsekiya@yamanashi.ac.jp; Sugiyama, S.

    2014-09-15

    Highlights: • We have developed a HTS five-pole dual-band bandpass filter using stub-loaded hair-pin resonators. • The proposed dual-band BPF can independently control of the center frequency. • Flexibly adjustment of the bandwidth can be achieved by the H-shaped waveguide. • The proposed BPF is evaluated by simulation and measurement with good agreement. - Abstract: A HTS dual-band bandpass filter is developed to obtain sharp-cut off characteristics for mobile communication systems. The filter is composed of five stub-loaded hair-pin resonators with H-shaped waveguides between them. The main advantage of the proposed filter is to allow independent control of the center frequency of the first and second bands. The bandwidths can be flexibly adjusted using the H-shaped waveguide. An electromagnetic simulator was used to design and analyze the filter, which have a 3.5-GHz center frequency and a 70-MHz (2%) bandwidth for the first band and a 5.0-GHz center frequency and a 100-MHz (2%) bandwidth for the second band. The filter was fabricated using YBa{sub 2}Cu{sub 3}O{sub y} thin film on an Al{sub 2}O{sub 3} substrate. Ground plane was fabricated using Au thin film. The measured frequency responses of the filter tally well with the simulated ones.

  6. Supersymmetric sigma models

    International Nuclear Information System (INIS)

    Bagger, J.A.

    1984-09-01

    We begin to construct the most general supersymmetric Lagrangians in one, two and four dimensions. We find that the matter couplings have a natural interpretation in the language of the nonlinear sigma model

  7. Supersymmetric sigma models

    Energy Technology Data Exchange (ETDEWEB)

    Bagger, J.A.

    1984-09-01

    We begin to construct the most general supersymmetric Lagrangians in one, two and four dimensions. We find that the matter couplings have a natural interpretation in the language of the nonlinear sigma model.

  8. SIGMA Experimental Facility; Facilidad Experimental SIGMA

    Energy Technology Data Exchange (ETDEWEB)

    Rivarola, Martin; Florido, Pablo; Gonzalez, Jose; Brasnarof, Daniel; Orellano, Pablo; Bergallo, Juan [Comision Nacional de Energia Atomica, Centro Atomico Bariloche, Grupo de Disenos Avanzados y Evaluacion Economica, Complejo Tecnologico Pilcaniyeu (Argentina)

    2000-07-01

    The SIGMA ( Separacion Isotopica Gaseosa por Metodos Avanzados) concept is outlined.The old gaseous diffusion process to enrich uranium has been updated to be economically competitive for small production volumes.Major innovations have been introduced in the membrane design and in the integrated design of compressors and diffusers.The use of injectors and gas turbines has been also adopted.The paper describes the demonstration facility installed by the Argentine Atomic Energy Commission.

  9. 6 Sigma project advance

    International Nuclear Information System (INIS)

    2002-12-01

    This book deals with 6 sigma project advance which introduces 6 sigma project in Changwon special steel, how is failure accepted? CTQ selection which is starting line, definition of performance standard, measurement system check on reliability of measurement data, check of process capacity for current level, establishment of target, optimal design and performance of application, practice of management system for maintain of improved result, CTQ selection, check of measurement system and practice of management system.

  10. Dynamical consequences of bandpass feedback loops in a bacterial phosphorelay.

    Directory of Open Access Journals (Sweden)

    Shaunak Sen

    Full Text Available Under conditions of nutrient limitation, Bacillus subtilis cells terminally differentiate into a dormant spore state. Progression to sporulation is controlled by a genetic circuit consisting of a phosphorelay embedded in multiple transcriptional feedback loops, which is used to activate the master regulator Spo0A by phosphorylation. These transcriptional regulatory interactions are "bandpass"-like, in the sense that activation occurs within a limited band of Spo0A∼P concentrations. Additionally, recent results show that the phosphorelay activation occurs in pulses, in a cell-cycle dependent fashion. However, the impact of these pulsed bandpass interactions on the circuit dynamics preceding sporulation remains unclear. In order to address this question, we measured key features of the bandpass interactions at the single-cell level and analyzed them in the context of a simple mathematical model. The model predicted the emergence of a delayed phase shift between the pulsing activity of the different sporulation genes, as well as the existence of a stable state, with elevated Spo0A activity but no sporulation, embedded within the dynamical structure of the system. To test the model, we used time-lapse fluorescence microscopy to measure dynamics of single cells initiating sporulation. We observed the delayed phase shift emerging during the progression to sporulation, while a re-engineering of the sporulation circuit revealed behavior resembling the predicted additional state. These results show that periodically-driven bandpass feedback loops can give rise to complex dynamics in the progression towards sporulation.

  11. Sigma models on supercosets

    Energy Technology Data Exchange (ETDEWEB)

    Mitev, Vladimir

    2010-08-15

    The purpose of this thesis is to deepen our understanding of the fundamental properties and defining features of non-linear sigma models on superspaces. We begin by presenting the major concepts that we have used in our investigation, namely Lie superalgebras and supergroups, non-linear sigma models and two dimensional conformal field theory. We then exhibit a method, called cohomological reduction, that makes use of the target space supersymmetry of non-linear sigma models to compute certain correlation functions. We then show how the target space supersymmetry of Ricci flat Lie supergroups simplifies the perturbation theory of suitable deformed Wess-Zumino-Witten models, making it possible to compute boundary conformal weights to all orders. This is then applied to the OSP (2S+2 vertical stroke 2S) Gross-Neveu Model, leading to a dual description in terms of the sigma model on the supersphere S{sup 2S+1} {sup vertical} {sup stroke} {sup 2S}. With this results in mind, we then turn to the similar, yet more intricate, theory of the non-linear sigma model on the complex projective superspaces CP{sup N-1} {sup vertical} {sup stroke} {sup N}. The cohomological reduction allows us to compute several important quantities non-perturbatively with the help of the system of symplectic fermions. Combining this with partial perturbative results for the whole theory, together with numerical computations, we propose a conjecture for the exact evolution of boundary conformal weights for symmetry preserving boundary conditions. (orig.)

  12. Sigma models on supercosets

    International Nuclear Information System (INIS)

    Mitev, Vladimir

    2010-08-01

    The purpose of this thesis is to deepen our understanding of the fundamental properties and defining features of non-linear sigma models on superspaces. We begin by presenting the major concepts that we have used in our investigation, namely Lie superalgebras and supergroups, non-linear sigma models and two dimensional conformal field theory. We then exhibit a method, called cohomological reduction, that makes use of the target space supersymmetry of non-linear sigma models to compute certain correlation functions. We then show how the target space supersymmetry of Ricci flat Lie supergroups simplifies the perturbation theory of suitable deformed Wess-Zumino-Witten models, making it possible to compute boundary conformal weights to all orders. This is then applied to the OSP (2S+2 vertical stroke 2S) Gross-Neveu Model, leading to a dual description in terms of the sigma model on the supersphere S 2S+1 vertical stroke 2S . With this results in mind, we then turn to the similar, yet more intricate, theory of the non-linear sigma model on the complex projective superspaces CP N-1 vertical stroke N . The cohomological reduction allows us to compute several important quantities non-perturbatively with the help of the system of symplectic fermions. Combining this with partial perturbative results for the whole theory, together with numerical computations, we propose a conjecture for the exact evolution of boundary conformal weights for symmetry preserving boundary conditions. (orig.)

  13. Inclusive $\\Sigma^{+}$ and $\\Sigma^{0}$ Production in Hadronic Z Decays

    CERN Document Server

    Acciarri, M.; Adriani, O.; Aguilar-Benitez, M.; Alcaraz, J.; Alemanni, G.; Allaby, J.; Aloisio, A.; Alviggi, M.G.; Ambrosi, G.; Anderhub, H.; Andreev, Valery P.; Angelescu, T.; Anselmo, F.; Arefev, A.; Azemoon, T.; Aziz, T.; Bagnaia, P.; Bajo, A.; Baksay, L.; Balandras, A.; Banerjee, S.; Banerjee, Sw.; Barczyk, A.; Barillere, R.; Barone, L.; Bartalini, P.; Basile, M.; Battiston, R.; Bay, A.; Becattini, F.; Becker, U.; Behner, F.; Bellucci, L.; Berbeco, R.; Berdugo, J.; Berges, P.; Bertucci, B.; Betev, B.L.; Bhattacharya, S.; Biasini, M.; Biland, A.; Blaising, J.J.; Blyth, S.C.; Bobbink, G.J.; Bohm, A.; Boldizsar, L.; Borgia, B.; Bourilkov, D.; Bourquin, M.; Braccini, S.; Branson, J.G.; Brigljevic, V.; Brochu, F.; Buffini, A.; Buijs, A.; Burger, J.D.; Burger, W.J.; Cai, X.D.; Campanelli, Mario; Capell, M.; Cara Romeo, G.; Carlino, G.; Cartacci, A.M.; Casaus, J.; Castellini, G.; Cavallari, F.; Cavallo, N.; Cecchi, C.; Cerrada, M.; Cesaroni, F.; Chamizo, M.; Chang, Y.H.; Chaturvedi, U.K.; Chemarin, M.; Chen, A.; Chen, G.; Chen, G.M.; Chen, H.F.; Chen, H.S.; Chiefari, G.; Cifarelli, L.; Cindolo, F.; Civinini, C.; Clare, I.; Clare, R.; Coignet, G.; Colijn, A.P.; Colino, N.; Costantini, S.; Cotorobai, F.; Cozzoni, B.; de la Cruz, B.; Csilling, A.; Cucciarelli, S.; Dai, T.S.; van Dalen, J.A.; D'Alessandro, R.; de Asmundis, R.; Deglon, P.; Degre, A.; Deiters, K.; della Volpe, D.; Denes, P.; DeNotaristefani, F.; De Salvo, A.; Diemoz, M.; van Dierendonck, D.; Di Lodovico, F.; Dionisi, C.; Dittmar, M.; Dominguez, A.; Doria, A.; Dova, M.T.; Duchesneau, D.; Dufournaud, D.; Duinker, P.; Duran, I.; El Mamouni, H.; Engler, A.; Eppling, F.J.; Erne, F.C.; Extermann, P.; Fabre, M.; Faccini, R.; Falagan, M.A.; Falciano, S.; Favara, A.; Fay, J.; Fedin, O.; Felcini, M.; Ferguson, T.; Ferroni, F.; Fesefeldt, H.; Fiandrini, E.; Field, J.H.; Filthaut, F.; Fisher, P.H.; Fisk, I.; Forconi, G.; Fredj, L.; Freudenreich, K.; Furetta, C.; Galaktionov, Iouri; Ganguli, S.N.; Garcia-Abia, Pablo; Gataullin, M.; Gau, S.S.; Gentile, S.; Gheordanescu, N.; Giagu, S.; Gong, Z.F.; Grenier, Gerald Jean; Grimm, O.; Gruenewald, M.W.; Guida, M.; van Gulik, R.; Gupta, V.K.; Gurtu, A.; Gutay, L.J.; Haas, D.; Hasan, A.; Hatzifotiadou, D.; Hebbeker, T.; Herve, Alain; Hidas, P.; Hirschfelder, J.; Hofer, H.; Holzner, G.; Hoorani, H.; Hou, S.R.; Hu, Y.; Iashvili, I.; Jin, B.N.; Jones, Lawrence W.; de Jong, P.; Josa-Mutuberria, I.; Khan, R.A.; Kaur, M.; Kienzle-Focacci, M.N.; Kim, D.; Kim, J.K.; Kirkby, Jasper; Kiss, D.; Kittel, W.; Klimentov, A.; Konig, A.C.; Kopp, A.; Koutsenko, V.; Kraber, M.; Kraemer, R.W.; Krenz, W.; Kruger, A.; Kunin, A.; Ladron Ladron de Guevara, P.; Laktineh, I.; Landi, G.; Lassila-Perini, K.; Lebeau, M.; Lebedev, A.; Lebrun, P.; Lecomte, P.; Lecoq, P.; Le Coultre, P.; Lee, H.J.; Le Goff, J.M.; Leiste, R.; Leonardi, Emanuele; Levtchenko, P.; Li, C.; Likhoded, S.; Lin, C.H.; Lin, W.T.; Linde, F.L.; Lista, L.; Liu, Z.A.; Lohmann, W.; Longo, E.; Lu, Y.S.; Lubelsmeyer, K.; Luci, C.; Luckey, David; Lugnier, L.; Luminari, L.; Lustermann, W.; Ma, W.G.; Maity, M.; Malgeri, L.; Malinin, A.; Mana, C.; Mangeol, D.; Mans, J.; Marchesini, P.; Marian, G.; Martin, J.P.; Marzano, F.; Massaro, G.G.G.; Mazumdar, K.; McNeil, R.R.; Mele, S.; Merola, L.; Meschini, M.; Metzger, W.J.; von der Mey, M.; Mihul, A.; Milcent, H.; Mirabelli, G.; Mnich, J.; Mohanty, G.B.; Molnar, P.; Monteleoni, B.; Moulik, T.; Muanza, G.S.; Muheim, F.; Muijs, A.J.M.; Musy, M.; Napolitano, M.; Nessi-Tedaldi, F.; Newman, H.; Niessen, T.; Nisati, A.; Kluge, Hannelies; Organtini, G.; Oulianov, A.; Palomares, C.; Pandoulas, D.; Paoletti, S.; Paolucci, P.; Paramatti, R.; Park, H.K.; Park, I.H.; Pascale, G.; Passaleva, G.; Patricelli, S.; Paul, Thomas Cantzon; Pauluzzi, M.; Paus, C.; Pauss, F.; Pedace, M.; Pensotti, S.; Perret-Gallix, D.; Petersen, B.; Piccolo, D.; Pierella, F.; Pieri, M.; Piroue, P.A.; Pistolesi, E.; Plyaskin, V.; Pohl, M.; Pojidaev, V.; Postema, H.; Pothier, J.; Produit, N.; Prokofev, D.O.; Prokofev, D.; Quartieri, J.; Rahal-Callot, G.; Rahaman, M.A.; Raics, P.; Raja, N.; Ramelli, R.; Rancoita, P.G.; Raspereza, A.; Raven, G.; Razis, P.; Ren, D.; Rescigno, M.; Reucroft, S.; van Rhee, T.; Riemann, S.; Riles, Keith; Robohm, A.; Rodin, J.; Roe, B.P.; Romero, L.; Rosca, A.; Rosier-Lees, S.; Rubio, J.A.; Ruschmeier, D.; Rykaczewski, H.; Saremi, S.; Sarkar, S.; Salicio, J.; Sanchez, E.; Sanders, M.P.; Sarakinos, M.E.; Schafer, C.; Schegelsky, V.; Schmidt-Kaerst, S.; Schmitz, D.; Schopper, H.; Schotanus, D.J.; Schwering, G.; Sciacca, C.; Sciarrino, D.; Seganti, A.; Servoli, L.; Shevchenko, S.; Shivarov, N.; Shoutko, V.; Shumilov, E.; Shvorob, A.; Siedenburg, T.; Son, D.; Smith, B.; Spillantini, P.; Steuer, M.; Stickland, D.P.; Stone, A.; Stone, H.; Stoyanov, B.; Straessner, A.; Sudhakar, K.; Sultanov, G.; Sun, L.Z.; Suter, H.; Swain, J.D.; Szillasi, Z.; Sztaricskai, T.; Tang, X.W.; Tauscher, L.; Taylor, L.; Tellili, B.; Timmermans, Charles; Ting, Samuel C.C.; Ting, S.M.; Tonwar, S.C.; Toth, J.; Tully, C.; Tung, K.L.; Uchida, Y.; Ulbricht, J.; Valente, E.; Vesztergombi, G.; Vetlitsky, I.; Vicinanza, D.; Viertel, G.; Villa, S.; Vivargent, M.; Vlachos, S.; Vodopianov, I.; Vogel, H.; Vogt, H.; Vorobev, I.; Vorobov, A.A.; Vorvolakos, A.; Wadhwa, M.; Wallraff, W.; Wang, M.; Wang, X.L.; Wang, Z.M.; Weber, A.; Weber, M.; Wienemann, P.; Wilkens, H.; Wu, S.X.; Wynhoff, S.; Xia, L.; Xu, Z.Z.; Yamamoto, J.; Yang, B.Z.; Yang, C.G.; Yang, H.J.; Yang, M.; Ye, J.B.; Yeh, S.C.; Zalite, A.; Zalite, Yu.; Zhang, Z.P.; Zhu, G.Y.; Zhu, R.Y.; Zichichi, A.; Zilizi, G.; Zoller, M.

    2000-01-01

    We report on measurements of the inclusive production rate of $\\Sigma^+$ and $\\Sigma^0$ baryons in hadronic Z decays collected with the L3 detector at LEP. The $\\Sigma^+$ baryons are detected through the decay $\\Sigma^+ \\rightarrow {\\rm p} \\pi^0$, while the $\\Sigma^0$ baryons are detected via the decay mode $\\Sigma^0 \\rightarrow \\Lambda \\gamma$. The average numbers of $\\Sigma^+$ and $\\Sigma^0$ per hadronic Z decay are measured to be: \\begin{eqnarray*} \\left + \\left & = & 0.114 \\pm 0.011_{\\mbox{\\it \\small stat}} \\pm 0.009_{\\mbox{\\it \\small syst}} \\\\ \\left + \\left & = & 0.095 \\pm 0.015_{\\mbox{\\it \\small stat}} \\pm 0.013_{\\mbox{\\it \\small syst}} \\ \\mbox{.} \\end{eqnarray*} These rates are found to be higher than the predictions from Monte Carlo hadronization models and analytical parameterizations of strange baryon production.

  14. A 1microW 85nV/ radicalHz pseudo open-loop preamplifier with programmable band-pass filter for neural interface system.

    Science.gov (United States)

    Chang, Sun-Il; Yoon, Euisik

    2009-01-01

    We report an energy efficient pseudo open-loop amplifier with programmable band-pass filter developed for neural interface systems. The proposed amplifier consumes 400nA at 2.5V power supply. The measured thermal noise level is 85nV/ radicalHz and input-referred noise is 1.69microV(rms) from 0.3Hz to 1 kHz. The amplifier has a noise efficiency factor of 2.43, the lowest in the differential topologies reported up to date to our knowledge. By programming the switched-capacitor frequency and bias current, we could control the bandwidth of the preamplifier from 138 mHz to 2.2 kHz to meet various application requirements. The entire preamplifier including band-pass filters has been realized in a small area of 0.043mm(2) using a 0.25microm CMOS technology.

  15. Continuous time sigma delta ADC design and non-idealities analysis

    International Nuclear Information System (INIS)

    Yuan Jun; Chen Zhenhai; Yang Yintang; Zhang Zhaofeng; Wu Jun; Wang Chao; Qian Wenrong

    2011-01-01

    A wide bandwidth continuous time sigma delta ADC is implemented in 130 nm CMOS. A detailed non-idealities analysis (excess loop delay, clock jitter, finite gain and GBW, comparator offset and DAC mismatch) is performed developed in Matlab/Simulink. This design is targeted for wide bandwidth applications such as video or wireless base-stations. Athird-order continuous time sigma delta modulator comprises a third-order RC operational-amplifier-based loop filter and 3-bit internal quantizer operated at 512 MHz clock frequency. The sigma delta ADC achieves 60 dB SNR and 59.3 dB SNDR over a 16-MHz signal band at an OSR of 16. The power consumption of the CT sigma delta modulator is 22 mW from the 1.2-V supply. (semiconductor integrated circuits)

  16. Six Sigma method

    NARCIS (Netherlands)

    Does, R.J.M.M.; de Mast, J.; Balakrishnan, N.; Brandimarte, P.; Everitt, B.; Molenberghs, G.; Piegorsch, W.; Ruggeri, F.

    2015-01-01

    Six Sigma is built on principles and methods that have proven themselves over the twentieth century. It has incorporated the most effective approaches and integrated them into a full program. It offers a management structure for organizing continuous improvement of routine tasks, such as

  17. Microstrip Cross-coupled Interdigital SIR Based Bandpass Filter

    Directory of Open Access Journals (Sweden)

    R. K. Maharjan

    2012-09-01

    Full Text Available A simple and compact 4.9 GHz bandpass filter for C-band applications is proposed. This paper presents a novel microstrip cross-coupled interdigital half-wavelength stepped impedance resonator (SIR based bandpass filter (BPF.The designed structure is similar to that of a combination of two parallel interdigital capacitors. The scattering parameters of the structure are measured using vector network analyzer (VNA. The self generated capacitive and inductive reactances within the interdigital resonators exhibited in a resonance frequency of 4.9 GHz. The resonant frequency and bandwidth of the capacitive cross-coupled resonator is directly optimized from the physical arrangement of the resonators. The measured insertion loss (S21 and return loss (S11 were 0.3 dB and 28 dB, respectively, at resonance frequency which were almost close to the simulation results.

  18. Application of HTSC-thin films in microwave bandpass filters

    International Nuclear Information System (INIS)

    Jha, A.R.

    1993-01-01

    This paper reveals unique performance capabilities of High-Temperature Superconducting Thin-Film (HTSCTFs) for possible applications in microwave bandpass filters (BPFs). Microwave filters fabricated with HTSCTFs have demonstrated lowest insertion loss, highest rejection, and sharpest skirt selectivity. Thin films of Yttrium Barium Copper Oxide (YBCO), Bismuth Strontium Calcium Copper Oxide (BSCCO) and Thallium Calcium Barium Copper Oxide (TCBCO) will be most attractive for filters

  19. An asymmetric MOSFET-C band-pass filter with on-chip charge pump auto-tuning

    International Nuclear Information System (INIS)

    Chen Fangxiong; Ma Heping; Jia Hailong; Shi Yin; Lin Min; Dai, Forster

    2009-01-01

    An asymmetric MOSFET-C band-pass filter (BPF) with on chip charge pump auto-tuning is presented. It is implemented in UMC (United Manufacturing Corporation) 0.18 μm CMOS process technology. The filter system with auto-tuning uses a master-slave technique for continuous tuning in which the charge pump outputs 2.663 V, much higher than the power supply voltage, to improve the linearity of the filter. The main filter with third order low-pass and second order high-pass properties is an asymmetric band-pass filter with bandwidth of 2.730-5.340 MHz. The in-band third order harmonic input intercept point (IIP3) is 16.621 dBm, with 50 Ω as the source impedance. The input referred noise is about 47.455 μV rms . The main filter dissipates 3.528 mW while the auto-tuning system dissipates 2.412 mW from a 1.8 V power supply. The filter with the auto-tuning system occupies 0.592 mm 2 and it can be utilized in GPS (global positioning system) and Bluetooth systems. (semiconductor integrated circuits)

  20. An asymmetric MOSFET-C band-pass filter with on-chip charge pump auto-tuning

    Energy Technology Data Exchange (ETDEWEB)

    Chen Fangxiong; Ma Heping; Jia Hailong; Shi Yin [Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Lin Min [Suzhou-CAS Semiconductors Integrated Technology Research Center, Suzhou 215021 (China); Dai, Forster, E-mail: fxchen@semi.ac.c [Department of Electrical and Computer Engineering, Auburn University, AL 36849 (United States)

    2009-08-15

    An asymmetric MOSFET-C band-pass filter (BPF) with on chip charge pump auto-tuning is presented. It is implemented in UMC (United Manufacturing Corporation) 0.18 {mu}m CMOS process technology. The filter system with auto-tuning uses a master-slave technique for continuous tuning in which the charge pump outputs 2.663 V, much higher than the power supply voltage, to improve the linearity of the filter. The main filter with third order low-pass and second order high-pass properties is an asymmetric band-pass filter with bandwidth of 2.730-5.340 MHz. The in-band third order harmonic input intercept point (IIP3) is 16.621 dBm, with 50 {Omega} as the source impedance. The input referred noise is about 47.455 {mu}V{sub rms}. The main filter dissipates 3.528 mW while the auto-tuning system dissipates 2.412 mW from a 1.8 V power supply. The filter with the auto-tuning system occupies 0.592 mm{sup 2} and it can be utilized in GPS (global positioning system) and Bluetooth systems. (semiconductor integrated circuits)

  1. Wide Bandpass and Narrow Bandstop Microstrip Filters based on Hilbert fractal geometry: design and simulation results.

    Directory of Open Access Journals (Sweden)

    Yaqeen S Mezaal

    Full Text Available This paper presents new Wide Bandpass Filter (WBPF and Narrow Bandstop Filter (NBSF incorporating two microstrip resonators, each resonator is based on 2nd iteration of Hilbert fractal geometry. The type of filter as pass or reject band has been adjusted by coupling gap parameter (d between Hilbert resonators using a substrate with a dielectric constant of 10.8 and a thickness of 1.27 mm. Numerical simulation results as well as a parametric study of d parameter on filter type and frequency responses are presented and studied. WBPF has designed at resonant frequencies of 2 and 2.2 GHz with a bandwidth of 0.52 GHz, -28 dB return loss and -0.125 dB insertion loss while NBSF has designed for electrical specifications of 2.37 GHz center frequency, 20 MHz rejection bandwidth, -0.1873 dB return loss and 13.746 dB insertion loss. The proposed technique offers a new alternative to construct low-cost high-performance filter devices, suitable for a wide range of wireless communication systems.

  2. Fully integrated low-loss band-pass filters for wireless applications

    International Nuclear Information System (INIS)

    Rais-Zadeh, M; Kapoor, A; Lavasani, H M; Ayazi, F

    2009-01-01

    Fully integrated low insertion loss micromachined band-pass filters are designed and fabricated on the silicon substrate (ρ = 10–20 Ω cm, ε r = 11.9) for UHF applications. Filters are made of silver, which has the highest conductivity of all metals, to minimize the ohmic loss. A detailed analysis for realizing low insertion loss and high out-of-band rejection filters using elliptic magnitude characteristics is presented, and a comprehensive model to take into account inductive parasitics of the interconnects is developed. Temperature characteristics of the filters are measured and show stable performance. The presented filters are different from the previously reported lumped element filters in that all filters are fully integrated on silicon substrate and occupy a remarkably smaller die area. Two filters are fabricated using the silver micromachining technique with center frequencies at 1.05 and 1.35 GHz. The filters have a constant 3 dB bandwidth of 300 MHz (28.6% and 22.2%) and an insertion loss of 1.4–1.7 dB. The low insertion loss and CMOS compatibility make the presented filters suitable candidates for radio frequency integrated circuits

  3. Design of an S band narrow-band bandpass BAW filter

    Science.gov (United States)

    Gao, Yang; Zhao, Kun-li; Han, Chao

    2017-11-01

    An S band narrowband bandpass filter BAW with center frequency 2.460 GHz, bandwidth 41MHz, band insertion loss - 1.154 dB, the passband ripple 0.9 dB, the out of band rejection about -42.5dB@2.385 GHz; -45.5dB@2.506 GHz was designed for potential UAV measurement and control applications. According to the design specifications, the design is as follows: each FBAR's stack was designed in BAW filter by using Mason model. Each FBAR's shape was designed with the method of apodization electrode. The layout of BAW filter was designed. The acoustic-electromagnetic cosimulation model was built to validate the performance of the designed BAW filter. The presented design procedure is a common one, and there are two characteristics: 1) an A and EM co-simulation method is used for the final BAW filter performance validation in the design stage, thus ensures over-optimistic designs by the bare 1D Mason model are found and rejected in time; 2) An in-house developed auto-layout method is used to get compact BAW filter layout, which simplifies iterative error-and-try work here and output necessary in-plane geometry information to the A and EM cosimulation model.

  4. Investigation of New Microstrip Bandpass Filter Based on Patch Resonator with Geometrical Fractal Slot.

    Directory of Open Access Journals (Sweden)

    Yaqeen S Mezaal

    Full Text Available A compact dual-mode microstrip bandpass filter using geometrical slot is presented in this paper. The adopted geometrical slot is based on first iteration of Cantor square fractal curve. This filter has the benefits of possessing narrower and sharper frequency responses as compared to microstrip filters that use single mode resonators and traditional dual-mode square patch resonators. The filter has been modeled and demonstrated by Microwave Office EM simulator designed at a resonant frequency of 2 GHz using a substrate of εr = 10.8 and thickness of h = 1.27 mm. The output simulated results of the proposed filter exhibit 22 dB return loss, 0.1678 dB insertion loss and 12 MHz bandwidth in the passband region. In addition to the narrow band gained, miniaturization properties as well as weakened spurious frequency responses and blocked second harmonic frequency in out of band regions have been acquired. Filter parameters including insertion loss, return loss, bandwidth, coupling coefficient and external quality factor have been compared with different values of perturbation dimension (d. Also, a full comparative study of this filter as compared with traditional square patch filter has been considered.

  5. DESIGN FOR SIX SIGMA

    Directory of Open Access Journals (Sweden)

    Liem Ferryanto

    2007-01-01

    Full Text Available This article provides a step by step process of executing analytical or computer based Design for Six Sigma using a Sliding Door project as an example. It comprises of identification of Voice Of the Customer (VOC, transformation of VOC to what it is called Critical To Quality characteristics (CTQs, modeling of system transfers function, optimal and robust solutions, and tolerance design approach

  6. SIGMA Experimental Facility

    International Nuclear Information System (INIS)

    Rivarola, Martin; Florido, Pablo; Gonzalez, Jose; Brasnarof, Daniel; Orellano, Pablo; Bergallo, Juan

    2000-01-01

    The SIGMA ( Separacion Isotopica Gaseosa por Metodos Avanzados) concept is outlined.The old gaseous diffusion process to enrich uranium has been updated to be economically competitive for small production volumes.Major innovations have been introduced in the membrane design and in the integrated design of compressors and diffusers.The use of injectors and gas turbines has been also adopted.The paper describes the demonstration facility installed by the Argentine Atomic Energy Commission

  7. Plasmonic Band-Pass Microfilters for LWIR Absorption Spectroscopy

    Directory of Open Access Journals (Sweden)

    J. M. Banks

    2012-01-01

    Full Text Available Absorption spectroscopy in the long wave infrared provides an effective method for identification of various hazardous chemicals. We present a theoretical design for plasmonic band-pass filters that can be used to provide wavelength selectivity for uncooled microbolometer sensors. The microfilters consist of a pair of input reflection gratings that couple light into a plasmonic waveguide with a central resonant waveguide cavity. An output transmission grating on the other side of the structure pulls light out of the waveguide where it is detected by a closely spaced sensor. Fabrication of the filters can be performed using standard photolithography procedures. A spectral bandpass with a full-width at half-maximum (FWHM of 100 nm can be obtained with a center wavelength spanning the entire 8–12 μm atmospheric transmission window by simple geometric scaling of only the lateral dimensions. This allows the simultaneous fabrication of all the wavelength filters needed for a full spectrometer on a chip.

  8. Sigma beta decay

    International Nuclear Information System (INIS)

    Newman, D.E.

    1975-01-01

    Describes an experiment to measure beta decays of the sigma particle. Sigmas produced by stopping a K - beam in a liquid hydrogen target decayed in the following reactions: Kp → Σπ; Σ → Neν. The electron and pion were detected by wire spark chambers in a magnetic spectrometer and by plastic scintillators, and were differentiated by a threshold gas Cherenkov counter. The neutron was detected by liquid scintillation counters. The data (n = 3) shell electrons or the highly excited electrons decay first. Instead, it is suggested that when there are two to five electrons in highly excited states immediately after a heavy ion--atom collision the first transitions to occur will be among highly excited Rydberg states in a cascade down to the 4s, 4p, and 3d-subshells. If one of the long lived states becomes occupied by electrons promoted during the collision or by electrons falling from higher levels, it will not decay until after the valence shell decays. LMM rates calculated to test the methods used are compared to previous works. The mixing coefficients are given in terms of the states 4s4p, 45sp+-, and 5s5p. The applicability of Cooper, Fano, and Prats' discussion of the energies and transition rates of doubly excited states is considered

  9. Observation of the Heavy Baryons Sigma b and Sigma b*.

    Science.gov (United States)

    Aaltonen, T; Abulencia, A; Adelman, J; Affolder, T; Akimoto, T; Albrow, M G; Amerio, S; Amidei, D; Anastassov, A; Anikeev, K; Annovi, A; Antos, J; Aoki, M; Apollinari, G; Arisawa, T; Artikov, A; Ashmanskas, W; Attal, A; Aurisano, A; Azfar, F; Azzi-Bacchetta, P; Azzurri, P; Bacchetta, N; Badgett, W; Barbaro-Galtieri, A; Barnes, V E; Barnett, B A; Baroiant, S; Bartsch, V; Bauer, G; Beauchemin, P-H; Bedeschi, F; Behari, S; Bellettini, G; Bellinger, J; Belloni, A; Benjamin, D; Beretvas, A; Beringer, J; Berry, T; Bhatti, A; Binkley, M; Bisello, D; Bizjak, I; Blair, R E; Blocker, C; Blumenfeld, B; Bocci, A; Bodek, A; Boisvert, V; Bolla, G; Bolshov, A; Bortoletto, D; Boudreau, J; Boveia, A; Brau, B; Brigliadori, L; Bromberg, C; Brubaker, E; Budagov, J; Budd, H S; Budd, S; Burkett, K; Busetto, G; Bussey, P; Buzatu, A; Byrum, K L; Cabrera, S; Campanelli, M; Campbell, M; Canelli, F; Canepa, A; Carillo, S; Carlsmith, D; Carosi, R; Carron, S; Casal, B; Casarsa, M; Castro, A; Catastini, P; Cauz, D; Cavalli-Sforza, M; Cerri, A; Cerrito, L; Chang, S H; Chen, Y C; Chertok, M; Chiarelli, G; Chlachidze, G; Chlebana, F; Cho, I; Cho, K; Chokheli, D; Chou, J P; Choudalakis, G; Chuang, S H; Chung, K; Chung, W H; Chung, Y S; Cilijak, M; Ciobanu, C I; Ciocci, M A; Clark, A; Clark, D; Coca, M; Compostella, G; Convery, M E; Conway, J; Cooper, B; Copic, K; Cordelli, M; Cortiana, G; Crescioli, F; Cuenca Almenar, C; Cuevas, J; Culbertson, R; Cully, J C; DaRonco, S; Datta, M; D'Auria, S; Davies, T; Dagenhart, D; de Barbaro, P; De Cecco, S; Deisher, A; De Lentdecker, G; De Lorenzo, G; Dell'Orso, M; Delli Paoli, F; Demortier, L; Deng, J; Deninno, M; De Pedis, D; Derwent, P F; Di Giovanni, G P; Dionisi, C; Di Ruzza, B; Dittmann, J R; D'Onofrio, M; Dörr, C; Donati, S; Dong, P; Donini, J; Dorigo, T; Dube, S; Efron, J; Erbacher, R; Errede, D; Errede, S; Eusebi, R; Fang, H C; Farrington, S; Fedorko, I; Fedorko, W T; Feild, R G; Feindt, M; Fernandez, J P; Field, R; Flanagan, G; Forrest, R; Forrester, S; Franklin, M; Freeman, J C; Furic, I; Gallinaro, M; Galyardt, J; Garcia, J E; Garberson, F; Garfinkel, A F; Gay, C; Gerberich, H; Gerdes, D; Giagu, S; Giannetti, P; Gibson, K; Gimmell, J L; Ginsburg, C; Giokaris, N; Giordani, M; Giromini, P; Giunta, M; Giurgiu, G; Glagolev, V; Glenzinski, D; Gold, M; Goldschmidt, N; Goldstein, J; Golossanov, A; Gomez, G; Gomez-Ceballos, G; Goncharov, M; González, O; Gorelov, I; Goshaw, A T; Goulianos, K; Gresele, A; Grinstein, S; Grosso-Pilcher, C; Grundler, U; Guimaraes da Costa, J; Gunay-Unalan, Z; Haber, C; Hahn, K; Hahn, S R; Halkiadakis, E; Hamilton, A; Han, B-Y; Han, J Y; Handler, R; Happacher, F; Hara, K; Hare, D; Hare, M; Harper, S; Harr, R F; Harris, R M; Hartz, M; Hatakeyama, K; Hauser, J; Hays, C; Heck, M; Heijboer, A; Heinemann, B; Heinrich, J; Henderson, C; Herndon, M; Heuser, J; Hidas, D; Hill, C S; Hirschbuehl, D; Hocker, A; Holloway, A; Hou, S; Houlden, M; Hsu, S-C; Huffman, B T; Hughes, R E; Husemann, U; Huston, J; Incandela, J; Introzzi, G; Iori, M; Ivanov, A; Iyutin, B; James, E; Jang, D; Jayatilaka, B; Jeans, D; Jeon, E J; Jindariani, S; Johnson, W; Jones, M; Joo, K K; Jun, S Y; Jung, J E; Junk, T R; Kamon, T; Karchin, P E; Kato, Y; Kemp, Y; Kephart, R; Kerzel, U; Khotilovich, V; Kilminster, B; Kim, D H; Kim, H S; Kim, J E; Kim, M J; Kim, S B; Kim, S H; Kim, Y K; Kimura, N; Kirsch, L; Klimenko, S; Klute, M; Knuteson, B; Ko, B R; Kondo, K; Kong, D J; Konigsberg, J; Korytov, A; Kotwal, A V; Kraan, A C; Kraus, J; Kreps, M; Kroll, J; Krumnack, N; Kruse, M; Krutelyov, V; Kubo, T; Kuhlmann, S E; Kuhr, T; Kulkarni, N P; Kusakabe, Y; Kwang, S; Laasanen, A T; Lai, S; Lami, S; Lammel, S; Lancaster, M; Lander, R L; Lannon, K; Lath, A; Latino, G; Lazzizzera, I; LeCompte, T; Lee, J; Lee, J; Lee, Y J; Lee, S W; Lefèvre, R; Leonardo, N; Leone, S; Levy, S; Lewis, J D; Lin, C; Lin, C S; Lindgren, M; Lipeles, E; Lister, A; Litvintsev, D O; Liu, T; Lockyer, N S; Loginov, A; Loreti, M; Lu, R-S; Lucchesi, D; Lujan, P; Lukens, P; Lungu, G; Lyons, L; Lys, J; Lysak, R; Lytken, E; Mack, P; MacQueen, D; Madrak, R; Maeshima, K; Makhoul, K; Maki, T; Maksimovic, P; Malde, S; Malik, S; Manca, G; Manousakis, A; Margaroli, F; Marginean, R; Marino, C; Marino, C P; Martin, A; Martin, M; Martin, V; Martínez, M; Martínez-Ballarín, R; Maruyama, T; Mastrandrea, P; Masubuchi, T; Matsunaga, H; Mattson, M E; Mazini, R; Mazzanti, P; McFarland, K S; McIntyre, P; McNulty, R; Mehta, A; Mehtala, P; Menzemer, S; Menzione, A; Merkel, P; Mesropian, C; Messina, A; Miao, T; Miladinovic, N; Miles, J; Miller, R; Mills, C; Milnik, M; Mitra, A; Mitselmakher, G; Miyamoto, A; Moed, S; Moggi, N; Mohr, B; Moon, C S; Moore, R; Morello, M; Movilla Fernandez, P; Mülmenstädt, J; Mukherjee, A; Muller, Th; Mumford, R; Murat, P; Mussini, M; Nachtman, J; Nagano, A; Naganoma, J; Nakamura, K; Nakano, I; Napier, A; Necula, V; Neu, C; Neubauer, M S; Nielsen, J; Nodulman, L; Norniella, O; Nurse, E; Oh, S H; Oh, Y D; Oksuzian, I; Okusawa, T; Oldeman, R; Orava, R; Osterberg, K; Pagliarone, C; Palencia, E; Papadimitriou, V; Papaikonomou, A; Paramonov, A A; Parks, B; Pashapour, S; Patrick, J; Pauletta, G; Paulini, M; Paus, C; Pellett, D E; Penzo, A; Phillips, T J; Piacentino, G; Piedra, J; Pinera, L; Pitts, K; Plager, C; Pondrom, L; Portell, X; Poukhov, O; Pounder, N; Prakoshyn, F; Pronko, A; Proudfoot, J; Ptohos, F; Punzi, G; Pursley, J; Rademacker, J; Rahaman, A; Ramakrishnan, V; Ranjan, N; Redondo, I; Reisert, B; Rekovic, V; Renton, P; Rescigno, M; Richter, S; Rimondi, F; Ristori, L; Robson, A; Rodrigo, T; Rogers, E; Rolli, S; Roser, R; Rossi, M; Rossin, R; Roy, P; Ruiz, A; Russ, J; Rusu, V; Saarikko, H; Safonov, A; Sakumoto, W K; Salamanna, G; Saltó, O; Santi, L; Sarkar, S; Sartori, L; Sato, K; Savard, P; Savoy-Navarro, A; Scheidle, T; Schlabach, P; Schmidt, E E; Schmidt, M A; Schmidt, M P; Schmitt, M; Schwarz, T; Scodellaro, L; Scott, A L; Scribano, A; Scuri, F; Sedov, A; Seidel, S; Seiya, Y; Semenov, A; Sexton-Kennedy, L; Sfyrla, A; Shalhout, S Z; Shapiro, M D; Shears, T; Shepard, P F; Sherman, D; Shimojima, M; Shochet, M; Shon, Y; Shreyber, I; Sidoti, A; Sinervo, P; Sisakyan, A; Slaughter, A J; Slaunwhite, J; Sliwa, K; Smith, J R; Snider, F D; Snihur, R; Soderberg, M; Soha, A; Somalwar, S; Sorin, V; Spalding, J; Spinella, F; Spreitzer, T; Squillacioti, P; Stanitzki, M; Staveris-Polykalas, A; St Denis, R; Stelzer, B; Stelzer-Chilton, O; Stentz, D; Strologas, J; Stuart, D; Suh, J S; Sukhanov, A; Sun, H; Suslov, I; Suzuki, T; Taffard, A; Takashima, R; Takeuchi, Y; Tanaka, R; Tecchio, M; Teng, P K; Terashi, K; Tesarek, R J; Thom, J; Thompson, A S; Thomson, E; Tipton, P; Tiwari, V; Tkaczyk, S; Toback, D; Tokar, S; Tollefson, K; Tomura, T; Tonelli, D; Torre, S; Torretta, D; Tourneur, S; Trischuk, W; Tsuno, S; Tu, Y; Turini, N; Ukegawa, F; Uozumi, S; Vallecorsa, S; van Remortel, N; Varganov, A; Vataga, E; Vazquez, F; Velev, G; Vellidis, C; Veramendi, G; Veszpremi, V; Vidal, M; Vidal, R; Vila, I; Vilar, R; Vine, T; Vogel, M; Vollrath, I; Volobouev, I; Volpi, G; Würthwein, F; Wagner, P; Wagner, R G; Wagner, R L; Wagner, J; Wagner, W; Wallny, R; Wang, S M; Warburton, A; Waters, D; Weinberger, M; Wester, W C; Whitehouse, B; Whiteson, D; Wicklund, A B; Wicklund, E; Williams, G; Williams, H H; Wilson, P; Winer, B L; Wittich, P; Wolbers, S; Wolfe, C; Wright, T; Wu, X; Wynne, S M; Yagil, A; Yamamoto, K; Yamaoka, J; Yamashita, T; Yang, C; Yang, U K; Yang, Y C; Yao, W M; Yeh, G P; Yoh, J; Yorita, K; Yoshida, T; Yu, G B; Yu, I; Yu, S S; Yun, J C; Zanello, L; Zanetti, A; Zaw, I; Zhang, X; Zhou, J; Zucchelli, S

    2007-11-16

    We report an observation of new bottom baryons produced in pp collisions at the Tevatron. Using 1.1 fb(-1) of data collected by the CDF II detector, we observe four Lambda b 0 pi+/- resonances in the fully reconstructed decay mode Lambda b 0-->Lambda c + pi-, where Lambda c+-->pK* pi+. We interpret these states as the Sigma b(*)+/- baryons and measure the following masses: m Sigma b+=5807.8 -2.2 +2.0(stat.)+/-1.7(syst.) MeV/c2, m Sigma b- =5815.2+/-1.0(stat.)+/-1.7(syst.) MeV/c2, and m(Sigma b*)-m(Sigma b)=21.2-1.9 +2.0(stat.)-0.3+0.4(syst.) MeV/c2.

  10. Study of SNS and SIS NbN Josephson junctions coupled to a microwave band-pass filter

    Energy Technology Data Exchange (ETDEWEB)

    Baggetta, E; Setzu, R; Villegier, J C [Laboratoire de Cryophysique, DRFMC, CEA, Grenoble (France)

    2006-06-01

    We have fabricated both NbN/Ta{sub x}N/NbN SN*S-type, NbN/MgO/NbN SIS-type Josephson junctions and microwave band-pass filters on different substrates (Si, Sapphire, MgO). NbN films have been deposited on both sides of (100) oriented, 250 {mu}m thick, MgO substrates with a high crystalline texture quality. The aim was to investigate the performances and the maximum achievable operating frequency in an NbN based RSFQ modulator front-end of an ADC in the 4 K-10 K temperature range. We observed that Ta{sub x}N thin films can be tuned from an insulating phase to a superconducting phase (Tc {approx}4K) by varying the nitrogen content during sputter deposition while the barrier height of MgO can also be controlled by deposition conditions and by tri-layer postdeposition annealing. Junction properties (Jc{approx}10-25 kA/cm{sup 2}), Mac Cumber parameter and RnIc product measured up to 1 mV are shown to be controlled by the reactive sputtering conditions. We have designed three pole band-pass filters and resonators in a micro-strip configuration and studied the junction coupling with the filters. We will show that a sigma-delta NbN technology is a suitable solution for analogue-to-digital conversion in the future generations of telecommunication satellites to achieve high sampling frequency and large bandwidth at high carrier frequency signal.

  11. Study of SNS and SIS NbN Josephson junctions coupled to a microwave band-pass filter

    International Nuclear Information System (INIS)

    Baggetta, E; Setzu, R; Villegier, J C

    2006-01-01

    We have fabricated both NbN/Ta x N/NbN SN*S-type, NbN/MgO/NbN SIS-type Josephson junctions and microwave band-pass filters on different substrates (Si, Sapphire, MgO). NbN films have been deposited on both sides of (100) oriented, 250 μm thick, MgO substrates with a high crystalline texture quality. The aim was to investigate the performances and the maximum achievable operating frequency in an NbN based RSFQ modulator front-end of an ADC in the 4 K-10 K temperature range. We observed that Ta x N thin films can be tuned from an insulating phase to a superconducting phase (Tc ∼4K) by varying the nitrogen content during sputter deposition while the barrier height of MgO can also be controlled by deposition conditions and by tri-layer postdeposition annealing. Junction properties (Jc∼10-25 kA/cm 2 ), Mac Cumber parameter and RnIc product measured up to 1 mV are shown to be controlled by the reactive sputtering conditions. We have designed three pole band-pass filters and resonators in a micro-strip configuration and studied the junction coupling with the filters. We will show that a sigma-delta NbN technology is a suitable solution for analogue-to-digital conversion in the future generations of telecommunication satellites to achieve high sampling frequency and large bandwidth at high carrier frequency signal

  12. Reconfigurable Bandpass Sigma-Delta Modulator With Programmable NTF for Low-IF Multi-Mode Receivers

    DEFF Research Database (Denmark)

    Zhang, Ke; Mikkelsen, Jan H.; Shen, Ming

    2012-01-01

    transfer function of the loop while still maintaining stability. Compared with conventional multi-mode BPSDM, employing cascade structures and multi-bit sub-ADCs, the proposed modulator features many attractive advantages, such as (1) avoiding coefficient mismatch between analog and digital components...

  13. Manage your human sigma.

    Science.gov (United States)

    Fleming, John H; Coffman, Curt; Harter, James K

    2005-01-01

    If sales and service organizations are to improve, they must learn to measure and manage the quality of the employee-customer encounter. Quality improvement methodologies such as Six Sigma are extremely useful in manufacturing contexts, but they're less useful when it comes to human interactions. To address this problem, the authors have developed a quality improvement approach they refer to as Human Sigma. It weaves together a consistent method for assessing the employee-customer encounter and a disciplined process for managing and improving it. There are several core principles for measuring and managing the employee-customer encounter: It's important not to think like an economist or an engineer when assessing interactions because emotions inform both sides' judgments and behavior. The employee-customer encounter must be measured and managed locally, because there are enormous variations in quality at the work-group and individual levels. And to improve the quality of the employee-customer interaction, organizations must conduct both short-term, transactional interventions and long-term, transformational ones. Employee engagement and customer engagement are intimately connected--and, taken together, they have an outsized effect on financial performance. They therefore need to be managed holistically. That is, the responsibility for measuring and monitoring the health of employee-customer relationships must reside within a single organizational structure, with an executive champion who has the authority to initiate and manage change. Nevertheless, the local manager remains the single most important factor in local group performance. A local manager whose work group shows suboptimal performance should be encouraged to conduct interventions, such as targeted training, performance reviews, action learning, and individual coaching.

  14. High-Q Bandpass Comb Filter for Mains Interference Extraction

    Directory of Open Access Journals (Sweden)

    Neycheva T.

    2009-12-01

    Full Text Available This paper presents a simple digital high-Q bandpass comb filter for power-line (PL or other periodical interference extraction. The filter concept relies on a correlated signal average resulting in alternating constructive and destructive spectrum interference i.e. the so-called comb frequency response. The presented filter is evaluated by Matlab simulations with real ECG signal contaminated with low amplitude PL interference. The made simulations show that this filter accurately extract the PL interference. It has high-Q notches only at PL odd harmonics and is appropriate for extraction of any kind of odd harmonic interference including rectangular shape. The filter is suitable for real-time operation with popular low-cost microcontrollers.

  15. A 65mW,0.4-2.3 GHz bandpass filter for satellite receivers

    NARCIS (Netherlands)

    Tang, van der J.D.; Kasperkovitz, D.; Bretveld, A.

    2002-01-01

    A monolithic tunable bandpass filter for satellite receiver front-ends is presented. The nter frequency of the bandpass filter can be tuned from 0.4 GHz to 2.3 GHz. The filter is constructed using four transconductor-C poly-phase filter sections and has a 50 dB variable gain range. At 20 dB

  16. Spectral design of temperature-invariant narrow bandpass filters for the mid-infrared

    DEFF Research Database (Denmark)

    Stolberg-Rohr, Thomine Kirstine; Hawkins, Gary J.

    2015-01-01

    The ability of narrow bandpass filters to discriminatewavelengths between closely-separated gas absorption lines is crucial inmany areas of infrared spectroscopy. As improvements to the sensitivity ofinfrared detectors enables operation in uncontrolled high-temperature environments, this imposes ...... presents the results of an investigation into the interdependence between multilayer bandpass designand optical materials together with a review on invariance at elevated temperatures....

  17. Performance of high-temperature superconducting band-pass filters with high selectivity for base transceiver applications of digital cellular communication systems

    Science.gov (United States)

    Kwak, J. S.; Lee, J. H.; Kim, C. O.; Hong, J. P.; Han, S. K.; Char, K.

    2002-07-01

    Highly selective high-temperature superconducting band-pass filters based on spiral meander line structures have been developed for base transceiver station applications of digital cellular communication systems. The filter comprised 12-pole microstrip line resonators with a circuit size of 0.5 × 17 × 41 mm3. The filter was designed to have a bandwidth of 25 MHz at a centre frequency of 834 MHz. Particularly, the physical size of each resonator was chosen not only to reduce far-field radiation, but also to have reasonable tunability in the filter. Device characteristics exhibited a low insertion loss of 0.4 dB with a 0.2 dB ripple and a return loss better than 10 dB in the pass-band at 65 K. The out-of-band signals were attenuated better than 60 dB at about 3.5 MHz from the lower band edge, and 3.8 MHz from the higher band edge.

  18. Performance of high-temperature superconducting band-pass filters with high selectivity for base transceiver applications of digital cellular communication systems

    Energy Technology Data Exchange (ETDEWEB)

    Kwak, J.S.; Lee, J.H.; Kim, C.O.; Hong, J.P. [Department of Physics, Hanyang University, Seoul (Korea, Republic of); Han, S.K.; Char, K. [RFtron Inc., Seoul (Korea, Republic of)

    2002-07-01

    Highly selective high-temperature superconducting band-pass filters based on spiral meander line structures have been developed for base transceiver station applications of digital cellular communication systems. The filter comprised 12-pole microstrip line resonators with a circuit size of 0.5x17x41 mm{sup 3}. The filter was designed to have a bandwidth of 25 MHz at a centre frequency of 834 MHz. Particularly, the physical size of each resonator was chosen not only to reduce far-field radiation, but also to have reasonable tunability in the filter. Device characteristics exhibited a low insertion loss of 0.4 dB with a 0.2 dB ripple and a return loss better than 10 dB in the pass-band at 65 K. The out-of-band signals were attenuated better than 60 dB at about 3.5 MHz from the lower band edge, and 3.8 MHz from the higher band edge. (author)

  19. Performance of high-temperature superconducting band-pass filters with high selectivity for base transceiver applications of digital cellular communication systems

    International Nuclear Information System (INIS)

    Kwak, J.S.; Lee, J.H.; Kim, C.O.; Hong, J.P.; Han, S.K.; Char, K.

    2002-01-01

    Highly selective high-temperature superconducting band-pass filters based on spiral meander line structures have been developed for base transceiver station applications of digital cellular communication systems. The filter comprised 12-pole microstrip line resonators with a circuit size of 0.5x17x41 mm 3 . The filter was designed to have a bandwidth of 25 MHz at a centre frequency of 834 MHz. Particularly, the physical size of each resonator was chosen not only to reduce far-field radiation, but also to have reasonable tunability in the filter. Device characteristics exhibited a low insertion loss of 0.4 dB with a 0.2 dB ripple and a return loss better than 10 dB in the pass-band at 65 K. The out-of-band signals were attenuated better than 60 dB at about 3.5 MHz from the lower band edge, and 3.8 MHz from the higher band edge. (author)

  20. Spectra of coset sigma models

    Energy Technology Data Exchange (ETDEWEB)

    Candu, Constantin [Institut fuer Theoretische Physik, Zuerich (Switzerland); Mitev, Vladimir [Humboldt-Universitaet, Berlin (Germany). Inst. fuer Mathematik; Humboldt-Universitaet, Berlin (Germany). Inst. fuer Physik; Schomerus, Volker [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany). Theory Group

    2013-08-15

    We compute the complete 1-loop spectrum of anomalous dimensions for the bulk fields of non-linear sigma models on symmetric coset (super)spaces G/H, both with and without world-sheet supersymmetry. In addition, we provide two new methods for the construction of partition functions in the infinite radius limit and demonstrate their efficiency in the case of (super)sphere sigma models. Our results apply to a large number of target spaces including superspheres and superprojective spaces such as the N=2 sigma model on CP{sup 3} {sup vertical} {sup stroke} {sup 4}.

  1. Six sigma for revenue retrieval.

    Science.gov (United States)

    Plonien, Cynthia

    2013-01-01

    Deficiencies in revenue retrieval due to failures in obtaining charges have contributed to a negative bottom line for numerous hospitals. Improving documentation practices through a Six Sigma process improvement initiative can minimize opportunities for errors through reviews and instill structure for compliance and consistency. Commitment to the Six Sigma principles with continuous monitoring of outcomes and constant communication of results to departments, management, and payers is a strong approach to reducing the financial impact of denials on an organization's revenues and expenses. Using Six Sigma tools can help improve the organization's financial performance not only for today, but also for health care's uncertain future.

  2. Spectra of coset sigma models

    International Nuclear Information System (INIS)

    Candu, Constantin; Mitev, Vladimir; Humboldt-Universitaet, Berlin; Schomerus, Volker

    2013-08-01

    We compute the complete 1-loop spectrum of anomalous dimensions for the bulk fields of non-linear sigma models on symmetric coset (super)spaces G/H, both with and without world-sheet supersymmetry. In addition, we provide two new methods for the construction of partition functions in the infinite radius limit and demonstrate their efficiency in the case of (super)sphere sigma models. Our results apply to a large number of target spaces including superspheres and superprojective spaces such as the N=2 sigma model on CP 3 vertical stroke 4 .

  3. Tracking the business cycle of the Euro area: A multivariate model-based band-pass filter

    NARCIS (Netherlands)

    Azevedo, J.M.; Koopman, S.J.; Rua, A.

    2006-01-01

    This article proposes a multivariate bandpass filter based on the trend plus cycle decomposition model. The underlying multivariate dynamic factor model relies on specific formulations for trend and cycle components and produces smooth business cycle indicators with bandpass filter properties.

  4. Running Head: Implementing Six Sigma Efforts

    Science.gov (United States)

    Lindsay, Jamie Eleaitia Mae

    2005-01-01

    Six Sigma is an organization wide program that provides common set of goals, language, and methodology for improving the overall quality of the processes within the organization (Davis & Heineke 2004). Six Sigma main concern is for the customer. What will the customers want? Need? Six Sigma has a model that helps Sigma get implemented DMAIC model…

  5. CMOS Bit-Stream Band-Pass Beamforming

    Science.gov (United States)

    2016-03-31

    unlimited. with direct IF sampling, most of the signal processing, including digital down-conversion ( DDC ), is carried out in the digital domain, and I/Q...level digitized signals are directly processed without decimation filtering for I/Q DDC and phase shifting. This novel BSP approach replaces bulky...positive feedback. The resonator center frequency of fs/4 (260MHz) simplifies the design of DDC . 4b tunable capacitors adjust the center frequency

  6. A Delta-Sigma beamformer with integrated apodization

    DEFF Research Database (Denmark)

    Tomov, Borislav Gueorguiev; Stuart, Matthias Bo; Hemmsen, Martin Christian

    2013-01-01

    This paper presents a new design of a discrete time Delta-Sigma (ΔΣ) oversampled ultrasound beamformer which integrates individual channel apodization by means of variable feedback voltage in the Delta-Sigma analog to digital (A/D) converters. The output bit-width of each oversampled A/D converter...... remains the same as in an unmodified one. The outputs of all receiving channels are delayed and summed, and the resulting multi-bit sample stream is filtered and decimated to become an image line. The simplicity of this beamformer allows the production of high-channel-count or very compact beamformers....... The data are acquired using 12-bit flash A/D converters at a sampling rate of 70 MHz, and are then upsampled off-line to 560 MHz for input to the simulated ΔΣ beamformer. The latter generates a B-mode image which is compared to that produced by a digital beamformer that uses 10-bit A/D converters...

  7. Invited Article: Narrowband terahertz bandpass filters employing stacked bilayer metasurface antireflection structures

    Science.gov (United States)

    Chang, Chun-Chieh; Huang, Li; Nogan, John; Chen, Hou-Tong

    2018-05-01

    We experimentally demonstrate high-performance narrowband terahertz (THz) bandpass filters through cascading multiple bilayer metasurface antireflection structures. Each bilayer metasurface, consisting of a square array of silicon pillars with a self-aligned top gold resonator-array and a complementary bottom gold slot-array, enables near-zero reflection and simultaneously close-to-unity single-band transmission at designed operational frequencies in the THz spectral region. The THz bandpass filters based on stacked bilayer metasurfaces allow a fairly narrow, high-transmission passband, and a fast roll-off to an extremely clean background outside the passband, thereby providing superior bandpass performance. The demonstrated scheme of narrowband THz bandpass filtering is of great importance for a variety of applications where spectrally clean, high THz transmission over a narrow bandwidth is desired, such as THz spectroscopy and imaging, molecular detection and monitoring, security screening, and THz wireless communications.

  8. Tunable bandpass filter based on photonic crystal fiber filled with multiple liquid crystals

    DEFF Research Database (Denmark)

    Scolari, Lara; Tartarini, G.; Borelli, E.

    2007-01-01

    A tunable bandpass filter based on a photonic crystal fiber filled with two different liquid crystals is demonstrated. 130 nm bandwidth tunability is achieved by tuning the temperature from 30degC to 90degC.......A tunable bandpass filter based on a photonic crystal fiber filled with two different liquid crystals is demonstrated. 130 nm bandwidth tunability is achieved by tuning the temperature from 30degC to 90degC....

  9. Auditory stream segregation using amplitude modulated bandpass noise

    Directory of Open Access Journals (Sweden)

    Yingjiu eNie

    2015-08-01

    Full Text Available The purpose of this study was to investigate the roles of spectral overlap and amplitude modulation (AM rate for stream segregation for noise signals, as well as to test the build-up effect based on these two cues. Segregation ability was evaluated using an objective paradigm with listeners’ attention focused on stream segregation. Stimulus sequences consisted of two interleaved sets of bandpass noise bursts (A and B bursts. The A and B bursts differed in spectrum, AM-rate, or both. The amount of the difference between the two sets of noise bursts was varied. Long and short sequences were studied to investigate the build-up effect for segregation based on spectral and AM-rate differences. Results showed the following: 1. Stream segregation ability increased with greater spectral separation. 2. Larger AM-rate separations were associated with stronger segregation abilities. 3. Spectral separation was found to elicit the build-up effect for the range of spectral differences assessed in the current study. 4. AM-rate separation interacted with spectral separation suggesting an additive effect of spectral separation and AM-rate separation on segregation build-up. The findings suggest that, when normal-hearing listeners direct their attention toward segregation, they are able to segregate auditory streams based on reduced spectral contrast cues that vary by the amount of spectral overlap. Further, regardless of the spectral separation they were able to use AM-rate difference as a secondary/weaker cue. Based on the spectral differences, listeners can segregate auditory streams better as the listening duration is prolonged—i.e. sparse spectral cues elicit build-up segregation; however, AM-rate differences only appear to elicit build-up when in combination with spectral difference cues.

  10. Inversion of the OH 1720-MHz line

    International Nuclear Information System (INIS)

    Elitzur, M.

    1975-01-01

    It is shown that the OH 1720-MHz line can be strongly inverted by collisions which excite the rotation states. It is also argued that radiative pumps (of any wave length) can invert strongly only the 1612-MHz line. (author)

  11. Design of high–order HTS dual–band bandpass filters with receiver subsystem for future mobile communication systems

    Energy Technology Data Exchange (ETDEWEB)

    Sekiya, N., E-mail: nsekiya@yamanashi.ac.jp

    2016-08-15

    Highlights: • We have developed two high-order HTS dual-band BPFs with a receiver subsystem for future mobile communication systems. • We developed a method for flexibly adjusting the coupling coefficient for the two passbands. • We demonstrated an HTS dual-band BPF receiver subsystem that uses a pulse tube cryocooler and a wideband LNA. • The proposed BPF is evaluated by simulation and measurement with good agreement. - Abstract: We have developed two high-order high-temperature superconducting (HTS) dual-band bandpass filters (BPFs) with a receiver subsystem for future mobile communication systems. They feature stub-loaded hair-pin resonators with two types of microstrip lines between them. One has a six-pole design, and the other has an eight-pole design. Both were designed to operate at 2.15 GHz with a 43-MHz (2%) bandwidth for the lower passband and at 3.50 GHz with a 70-MHz (2%) bandwidth for the upper one. They were fabricated using YBa{sub 2}Cu{sub 3}O{sub y} thin film on a CeO{sub 2}-bufferd r-Al{sub 2}O{sub 3} substrate. The measured results for both filters agree well with the simulated ones. The HTS dual-band BPF receiver subsystem uses a pulse tube cryocooler and a wideband low noise amplifier (LNA). We measured the frequency response of the six-pole dual-band BPF with and without a wideband LNA with a gain of 10 dB. The measured return losses were close.

  12. SEMICONDUCTOR INTEGRATED CIRCUITS: An asymmetric MOSFET-C band-pass filter with on-chip charge pump auto-tuning

    Science.gov (United States)

    Fangxiong, Chen; Min, Lin; Heping, Ma; Hailong, Jia; Yin, Shi; Forster, Dai

    2009-08-01

    An asymmetric MOSFET-C band-pass filter (BPF) with on chip charge pump auto-tuning is presented. It is implemented in UMC (United Manufacturing Corporation) 0.18 μm CMOS process technology. The filter system with auto-tuning uses a master-slave technique for continuous tuning in which the charge pump outputs 2.663 V, much higher than the power supply voltage, to improve the linearity of the filter. The main filter with third order low-pass and second order high-pass properties is an asymmetric band-pass filter with bandwidth of 2.730-5.340 MHz. The in-band third order harmonic input intercept point (IIP3) is 16.621 dBm, with 50 Ω as the source impedance. The input referred noise is about 47.455 μVrms. The main filter dissipates 3.528 mW while the auto-tuning system dissipates 2.412 mW from a 1.8 V power supply. The filter with the auto-tuning system occupies 0.592 mm2 and it can be utilized in GPS (global positioning system) and Bluetooth systems.

  13. The SIGMA plants economic behavior

    International Nuclear Information System (INIS)

    Rivarola, Martin E.; Bergallo, Juan E.

    1999-01-01

    In this work, the economical behavior of the Uranium Enrichment Plants, built using the Gaseous Isotopic Separation using Advanced Methods (SIGMA) (Separacion Isotopica Gaseosa por Metodos Avanzados) technology is analyzed. The calculations were made using an integrated computer code, where the cost of each main component of the plant is estimated. The program computes the production cost for several configurations of enrichment cascades, each one corresponding to a production rate. The program also includes a numerical optimizer and it seeks the SIGMA optimal configuration for a given set of design parameters. The present work does not contemplate the model and calculation of the auxiliary system costs. The total amortization cost is obtained by using the cascade capital cost and assuming that the auxiliary system represents a fixed part of the total cost.The results obtained show that the SIGMA technology for Enrichment Uranium Plants could achieve economical competition in a much lower production scale than the conventional Gaseous Diffusion Enrichment Plants. (author)

  14. Spectra of conformal sigma models

    International Nuclear Information System (INIS)

    Tlapak, Vaclav

    2015-04-01

    In this thesis the spectra of conformal sigma models defined on (generalized) symmetric spaces are analysed. The spaces where sigma models are conformal without the addition of a Wess-Zumino term are supermanifolds, in other words spaces that include fermionic directions. After a brief review of the general construction of vertex operators and the background field expansion, we compute the diagonal terms of the one-loop anomalous dimensions of sigma models on semi-symmetric spaces. We find that the results are formally identical to the symmetric case. However, unlike for sigma models on symmetric spaces, off diagonal terms that lead to operator mixing are also present. These are not computed here. We then present a detailed analysis of the one-loop spectrum of the supersphere S 3 vertical stroke 2 sigma model as one of the simplest examples. The analysis illustrates the power and simplicity of the construction. We use this data to revisit a duality with the OSP(4 vertical stroke 2) Gross-Neveu model that was proposed by Candu and Saleur. With the help of a recent all-loop result for the anomalous dimension of (1)/(2)BPS operators of Gross-Neveu models, we are able to recover the entire zero-mode spectrum of the supersphere model. We also argue that the sigma model constraints and its equations of motion are implemented correctly in the Gross-Neveu model, including the one-loop data. The duality is further supported by a new all-loop result for the anomalous dimension of the ground states of the sigma model. However, higher-gradient operators cannot be completely recovered. It is possible that this discrepancy is related to a known instability of the sigma model. The instability of sigma models is due to symmetry preserving high-gradient operators that become relevant at arbitrarily small values of the coupling. This feature has been observed long ago in one-loop calculations of the O(N)-vector model and soon been realized to be a generic property of sigma models

  15. SIX SIGMA: A LITERATURE REVIEW

    Directory of Open Access Journals (Sweden)

    S.A. Oke

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: Despite stiff international competition in the global market, world-class manufacturers are increasing their market share and profits through low-cost production, waste reduction in manufacturing, production of high quality products, and exceptional customer service. Six Sigma has been successfully implemented in this regard. In this paper, a selected survey of Six Sigma literature is presented to illustrate the wide scope of the application of the concept. This could be of immense benefit to organizations’ top management who need to understand the critical variables and factors for the successful implementation of Six Sigma programmes, leading to substantial, sustainable long-term improvement in performance results, value for money, and effort. The paper presents motivated pointers – substantiated as far as possible by data and evidence – to key success factors, variables, and their interrelationships.

    AFRIKAANSE OPSOMMING: Sterk internasionale mededinging ten spyt verhoog wêreldklasvervaardigers hul markaandeel en winste via laekosteproduksie, skrootvermindering, die produksie van gehalteprodukte en die lewering van primadiens aan klante. Ses Sigma is in hierdie verband as gereedskap suksesvol geïmplimenteer. Die artikel behandel 'n gekeurde oorsig van Ses Sigmaliteratuur om sodoende die toepassingsveldwyde van die konsep te illustreer. Die artikel is nuttig vir organisasiebestuurders uit die oogpunt van veranderlikes en suksesfaktore wat deur die Ses Sigmametode tot substansiële en volhoubare langtermyn verbeterings van 'n onderneming kan lei.

  16. Measuring emittances and sigma matrices

    International Nuclear Information System (INIS)

    Rees, J.; Rivkin, L.

    1984-03-01

    The method used for measuring emittance at the SLAC Linac and the linear collider damping ring is described. The basis of the method is derived using one two-by-two matrix to specify the state of the input beam (sigma matrix) and another to describe the lens-drift transport system (R-matrix)

  17. Six Sigma in healthcare delivery.

    Science.gov (United States)

    Liberatore, Matthew J

    2013-01-01

    The purpose of this paper is to conduct a comprehensive review and assessment of the extant Six Sigma healthcare literature, focusing on: application, process changes initiated and outcomes, including improvements in process metrics, cost and revenue. Data were obtained from an extensive literature search. Healthcare Six Sigma applications were categorized by functional area and department, key process metric, cost savings and revenue generation (if any) and other key implementation characteristics. Several inpatient care areas have seen most applications, including admission, discharge, medication administration, operating room (OR), cardiac and intensive care. About 42.1 percent of the applications have error rate as their driving metric, with the remainder focusing on process time (38 percent) and productivity (18.9 percent). While 67 percent had initial improvement in the key process metric, only 10 percent reported sustained improvement. Only 28 percent reported cost savings and 8 percent offered revenue enhancement. These results do not favorably assess Six Sigma's overall effectiveness and the value it offers healthcare. Results are based on reported applications. Future research can include directly surveying healthcare organizations to provide additional data for assessment. Future application should emphasize obtaining improvements that lead to significant and sustainable value. Healthcare staff can use the results to target promising areas. This article comprehensively assesses Six Sigma healthcare applications and impact.

  18. Lean Six Sigma in financial services

    NARCIS (Netherlands)

    de Koning, H.; Does, R.J.M.M.; Bisgaard, S.

    2008-01-01

    Lean Thinking and Six Sigma are typically considered as separate approaches to process innovation, with complementary strengths. When combined as Lean Six Sigma, this approach provides a unified framework for systematically developing innovations. Lean Six Sigma can also bring about significant

  19. Comparative Analysis between Lean, Six Sigma and Lean Six Sigma Concepts

    OpenAIRE

    Alexandra Mirela Cristina MUNTEANU

    2017-01-01

    This paper analyzes the benefits of Lean Six Sigma in comparison with Lean and Six Sigma, traditional improvement methodologies. The introduction highlights the appearance of Lean Six Sigma, early 2000s, as well as the benefits brought by the integrated approach. The following parts of the study emphasize the main differences between methodologies and their commonalities based on their synergy. Finally the advantages of Lean Six Sigma versus Lean and Six Sigma are analyzed and systematized by...

  20. Waveform digitizing at 500 MHz

    International Nuclear Information System (INIS)

    Atiya, M.; Ito, M.; Haggerty, J.; Ng, C.; Sippach, F.W.

    1988-01-01

    Experiment E787 at Brookhaven National Laboratory is designed to study the decay K + → π + ν/bar /nu// to a sensitivity of 2 /times/ 10 -10 . To achieve acceptable muon rejection it is necessary to couple traditional methods (range/energy/momentum correlation) with observation of the (π + → μ + ν, μ + → e + ν/bar /nu//) decay sequence in scintillator. We report on the design and construction of 200 channels of relatively low cost solid state waveform digitizers. The distinguishing features are: 8 bits dynamic range, 500 MHz sampling, zero suppression on the fly, deep memory (up to .5 msec), and fast readout time (100 μsec for the entire system). We report on data obtained during the February-May 1988 run showing performance of the system for the observation of the above decay. 8 figs

  1. Waveform digitizing at 500 MHz

    International Nuclear Information System (INIS)

    Atiya, M.; Ito, M.; Haggerty, J.; Ng, C.; Sippach, F.W.

    1988-01-01

    Experiment E787 at Brookhaven National Laboratory is designed to study the decay K + → π + ν/bar /nu// to a sensitivity of 2 /times/ 10/sup /minus/10/. To achieve acceptable muon rejection it is necessary to couple traditional methods (range/energy/momentum correlation) with observation of the π + → μ + → e + ν/bar /nu// decay sequence in scintillator. We report on the design and construction of over 200 channels of relatively low cost solid state waveform digitizers. The distinguishing features are: 8 bits dynamic range, 500 MHz sampling, zero suppression on the fly, deep memory (up to .5 msec), and fast readout time (100 μsec for the entire system). We report on data obtained during the February--May 1988 run showing performance of the system for the observation of the above decay. 9 figs

  2. Hadron properties in chiral sigma model

    International Nuclear Information System (INIS)

    Shen Hong

    2005-01-01

    The modification of hadron masses in nuclear medium is studied by using the chiral sigma model, which is extended to generate the omega meson mass by the sigma condensation in the vacuum in the same way as the nucleon mass. The chiral sigma model provides proper equilibrium properties of nuclear matter. It is shown that the effective masses of both nucleons and omega mesons decrease in nuclear medium, while the effective mass of sigma mesons increases oat finite density in the chiral sigma model. The results obtained in the chiral sigma model are compared with those obtained in the Walecka model, which includes sigma and omega mesons in a non-chiral fashion. (author)

  3. Introduction to sigma model anomalies

    International Nuclear Information System (INIS)

    Nelson, P.

    1985-01-01

    This paper presents results dealing with the specific case in which a sigma model with fermions arises as a result of dynamical symmetry breakdown from some group G to a subgroup H. H may contain chiral symmetries protecting some fermions in a representation ρ H of H. In this case it may be impossible to quantize the remaining fermions in a way which reproduces the anomalous Ward identities of any underlying strongly-interacting gauge theory. The author concludes that this pattern of symmetry breakdown will not be realized in any such theory. The criterion in this case is local in character, since roughly speaking once the sigma model in question behaves for field configurations close to the vacuum base point in the internal mainfold is known, symmetry can be used to find how it behaves everywhere else

  4. A Novel CPW BandPass Filter Integrating Periodic Rectangular Slot Cells

    Directory of Open Access Journals (Sweden)

    Fouad Aytouna

    2015-12-01

    Full Text Available In this paper, we introduce the design and the achievement of a Bandpass filter structure based on the use of rectangular slot cell. The originality of this work is to achieve a coplanar filter easy to integrate with microwave planar circuits and having a wide frequency bandwidth. The proposed bandpass filter is a low cost and compact planar filter structure. The final circuit is simulated by using two electromagnetic solvers, ADS and HFSS. The validation into simulation is based on using optimization methods integrated into the both solvers. Simulations have taken into account a high meshing density to cover the whole circuit. The fabricated bandpass filter has an area of 35X31mm2 and having a good insertion loss around -0.75dB in the bandwidth. The comparison between simulation and measurement results presents a good agreement.

  5. Dual and tri-band bandpass filters based on novel Π-shaped resonator

    Science.gov (United States)

    Xiao, Jian-Kang; Zhu, Wen-Jun; Zhao, Wei

    2014-05-01

    A novel Π-shaped resonator is proposed, and compact dual-band and tri-band bandpass filters that meet IEEE 802.11 application requirements by using the new resonator are designed. The dual-band bandpass filter centres at 2.45 and 5.6 GHz with a simulated passband insertion loss of no more than 0.8 dB, and the tri-band bandpass filter which is got by two-path coupling achieves simulated passband insertion loss of no more than 1.1 dB. The new designs are demonstrated by experiment. The new filters have advantages of simple and compact structures, low passband insertion losses, good frequency selectivity and miniature circuit sizes. All these have prospect to be applied in future wireless communication systems.

  6. Branes in Poisson sigma models

    International Nuclear Information System (INIS)

    Falceto, Fernando

    2010-01-01

    In this review we discuss possible boundary conditions (branes) for the Poisson sigma model. We show how to carry out the perturbative quantization in the presence of a general pre-Poisson brane and how this is related to the deformation quantization of Poisson structures. We conclude with an open problem: the perturbative quantization of the system when the boundary has several connected components and we use a different pre-Poisson brane in every component.

  7. Lean six sigma in healthcare.

    Science.gov (United States)

    de Koning, Henk; Verver, John P S; van den Heuvel, Jaap; Bisgaard, Soren; Does, Ronald J M M

    2006-01-01

    Healthcare, as with any other service operation, requires systematic innovation efforts to remain competitive, cost efficient, and up-to-date. This article outlines a methodology and presents examples to illustrate how principles of Lean Thinking and Six Sigma can be combined to provide an effective framework for producing systematic innovation efforts in healthcare. Controlling healthcare cost increases, improving quality, and providing better healthcare are some of the benefits of this approach.

  8. Topological sigma models on supermanifolds

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Bei, E-mail: beijia@physics.utexas.edu

    2017-02-15

    This paper concerns constructing topological sigma models governing maps from semirigid super Riemann surfaces to general target supermanifolds. We define both the A model and B model in this general setup by defining suitable BRST operators and physical observables. Using supersymmetric localization, we express correlation functions in these theories as integrals over suitable supermanifolds. In the case of the A model, we obtain an integral over the supermoduli space of “superinstantons”. The language of supergeometry is used extensively throughout this paper.

  9. Analogue demonstration of a high temperature superconducting sigma-delta modulator with 27 GHz sampling

    Energy Technology Data Exchange (ETDEWEB)

    Forrester, M.G.; Hunt, B.D.; Miller, D.L.; Talvacchio, J.; Young, R.M. [Northrop Grumman Science and Technology Center, Pittsburgh, PA 15235-5098 (United States)

    1999-11-01

    We have successfully fabricated and tested a high temperature superconducting (HTS) sigma-delta modulator for analogue-to-digital conversion. This is the first demonstration of a GHz sampling A-to-D in HTS. The 15-junction single-flux-quantum (SFQ) circuit, fabricated using an epitaxial multilayer HTS process with YBCO/Co-YBCO/YBCO edge junctions, was internally clocked at 27 GHz and used to convert a 5.01 MHz signal. The modulator demonstrated a spur-free dynamic range of more than 75 dB. Two-tone measurements with 5.01 MHz and 5.51 MHz signals demonstrated third-order intermodulation products to be lower than -59 dBc. Demonstration of a functional HTS modulator represents a significant milestone in the development of high dynamic range ADCs suitable for such applications as surveillance radar. (author)

  10. 47 CFR 101.77 - Public safety licensees in the 1850-1990 MHz, 2110-2150 MHz, and 2160-2200 MHz bands.

    Science.gov (United States)

    2010-10-01

    ..., 2110-2150 MHz, and 2160-2200 MHz bands. 101.77 Section 101.77 Telecommunication FEDERAL COMMUNICATIONS...-1990 MHz, 2110-2150 MHz, and 2160-2200 MHz bands. (a) In order for public safety licensees to qualify... a Police licensee, a Fire Licensee, or an Emergency Medical Licensee as defined in § 90.7 of this...

  11. High Selectivity Dual-Band Bandpass Filter with Tunable Lower Passband

    Directory of Open Access Journals (Sweden)

    Wei-Qiang Pan

    2015-01-01

    Full Text Available This paper presents a novel method to design dual-band bandpass filters with tunable lower passband and fixed upper passband. It utilizes a trimode resonator with three controllable resonant modes. Discriminating coupling is used to suppress the unwanted mode to avoid the interference. Varactors are utilized to realize tunable responses. The bandwidth of the two bands can be controlled individually. Transmission zeros are generated near the passband edges, resulting in high selectivity. For demonstration, a tunable bandpass filter is implemented. Good agreement between the prediction and measurement validates the proposed method.

  12. A Miniaturize Bandpass Filter with Harmonic Suppression Using Meandered Quarter-Wavelength Resonators

    Directory of Open Access Journals (Sweden)

    Yun-Long Lu

    2014-01-01

    Full Text Available A miniaturized bandpass filter with harmonics suppression is presented. The proposed filter consists of two quarter-wavelength microstrip resonators, which are meandered for circuit size reduction. An interdigital capacitor, loading at zero-voltage point, is employed to provide the desired coupling between the resonators at operating frequency, whereas the coupling coefficient at the third harmonic is realized to be zero. Besides, the second and fourth harmonics are suppressed since λ/4 resonators are adopted. Benefiting from these properties, a miniaturized bandpass filter with the second, third, and fourth harmonics suppression was designed and implemented. The final measured and simulated results show good consistence with the theoretical counterparts.

  13. Optical Interference Coatings Design Contest 2007: triple bandpass filter and nonpolarizing beam splitter.

    Science.gov (United States)

    Tilsch, Markus; Hendrix, Karen

    2008-05-01

    A triple bandpass filter (28 solutions received) and a nonpolarizing beam splitter (23 solutions received) were the subjects of the design contest held in conjunction with the 2007 Optical Interference Coatings topical meeting of the Optical Society of America. Fifteen designers participated using a wide spectrum of design approaches and optimization strategies to create the submissions. The results differ significantly, but all meet the contest requirements. Fabien Lemarchand wins both contests by submitting the thinnest (6254 nm) triple bandpass design and the widest (61.7 nm) nonpolarizing beam-splitter design. Michael Trubetskov is in second place, followed by Vladimir Pervak in both contests. The submitted designs are described and evaluated.

  14. A compact, higher order, high temperature superconductor microstrip bandpass filter on a two-inch lanthanum aluminate substrate for personal communication service applications

    International Nuclear Information System (INIS)

    Pal, Srikanta; Stevens, Chris; Edwards, David

    2005-01-01

    A practical design methodology for a compact parallel-coupled microstrip bandpass filter structure with steep attenuation is introduced using a computer-aided full wave electromagnetic simulation based on the method of moments. The structure consists of an array of fully aligned half-wavelength spiral meander line resonators. Aimed at application in the front-end receiver of digital cellular communication service, a 12-pole high temperature superconductor filter with 2.27% fractional bandwidth at 883.0 MHz was designed. The filter is fabricated using thallium-barium-calcium-copper oxide (TBCCO) thin films on a two-inch lanthanum aluminate (LaAlO 3 ) wafer. The S-parameter measurements show a good agreement with the simulated results. At 70 K, the 12-pole filter shows less than 0.4 dB insertion loss, 0.3 dB passband ripple, better than 12 dB return loss. The out of band rejection at 3 MHz below the passband edges is more than 60.0 dB. In order to estimate the power handling capability of the filter, the third-order intermodulation distortion was measured. A sensitivity analysis for the observed frequency shift in the filter is reported. Also from this analysis an approach for using the same design in 0.5% FBW applications is discussed

  15. Design and testing of a 750MHz CW-EPR digital console for small animal imaging.

    Science.gov (United States)

    Sato-Akaba, Hideo; Emoto, Miho C; Hirata, Hiroshi; Fujii, Hirotada G

    2017-11-01

    This paper describes the development of a digital console for three-dimensional (3D) continuous wave electron paramagnetic resonance (CW-EPR) imaging of a small animal to improve the signal-to-noise ratio and lower the cost of the EPR imaging system. A RF generation board, an RF acquisition board and a digital signal processing (DSP) & control board were built for the digital EPR detection. Direct sampling of the reflected RF signal from a resonator (approximately 750MHz), which contains the EPR signal, was carried out using a band-pass subsampling method. A direct automatic control system to reduce the reflection from the resonator was proposed and implemented in the digital EPR detection scheme. All DSP tasks were carried out in field programmable gate array ICs. In vivo 3D imaging of nitroxyl radicals in a mouse's head was successfully performed. Copyright © 2017 Elsevier Inc. All rights reserved.

  16. Design and testing of a 750 MHz CW-EPR digital console for small animal imaging

    Science.gov (United States)

    Sato-Akaba, Hideo; Emoto, Miho C.; Hirata, Hiroshi; Fujii, Hirotada G.

    2017-11-01

    This paper describes the development of a digital console for three-dimensional (3D) continuous wave electron paramagnetic resonance (CW-EPR) imaging of a small animal to improve the signal-to-noise ratio and lower the cost of the EPR imaging system. A RF generation board, an RF acquisition board and a digital signal processing (DSP) & control board were built for the digital EPR detection. Direct sampling of the reflected RF signal from a resonator (approximately 750 MHz), which contains the EPR signal, was carried out using a band-pass subsampling method. A direct automatic control system to reduce the reflection from the resonator was proposed and implemented in the digital EPR detection scheme. All DSP tasks were carried out in field programmable gate array ICs. In vivo 3D imaging of nitroxyl radicals in a mouse's head was successfully performed.

  17. Barriers of six sigma in healthcare organizations

    Directory of Open Access Journals (Sweden)

    Serkan Deniz

    2018-09-01

    Full Text Available Six Sigma approach is based on decreasing defects and variations in the products and processes, and it provides important benefits to healthcare organizations. This study aims to identify managers’ opinions, who work in private healthcare organizations, about the reasons behind not using Six Sigma in their organizations. The research was performed between December 2016 and March 2018 in private healthcare organizations (private hospitals and medical centers operating in Turkey and not using Six Sigma approach. Data were collected from managers, who have knowledge about Six Sigma, through using surveys. In this study, survey methodology was used to collect data. According to the results, the biggest barrier related to not using Six Sigma is based on the lack of knowledge about Six Sigma. The other important barrier about the diffusion of Six Sigma within this organizations is related to the lack of support from top management and leaders. Another finding about the reasons of not applying Six Sigma approach is that there is not a statistically significant difference among managers in terms of their managerial position. In order to overcome the lack of knowledge about Six Sigma, it is advised that managers should take steps in the direction of promoting Six Sigma within their current organization, and provide necessary support and leadership about the process.

  18. Design for six sigma: A review

    Directory of Open Access Journals (Sweden)

    Kouroush Jenab

    2018-01-01

    Full Text Available Six Sigma is recognized as an essential tool for continuous improvement of quality. A large num-ber of publications by various authors reflect the interest in this technique. Reviews of literature on Six Sigma have been done in the past by a few authors. However, considering the contributions in the recent times, a more comprehensive review is attempted here. The authors have examined vari-ous papers and have proposed a different scheme of classification. In addition, certain gaps that would provide hints for further research in Six Sigma have been identified. As a results the rela-tionship between Six Sigma, Design for Six Sigma (DFSS, and how these two concepts support the quality system for organizational learning and innovation performance have been discussed that would help researchers, academicians and practitioners to take a closer look at the growth, devel-opment and applicability of Six Sigma in Design.

  19. A Differential 4-Path Highly Linear Widely Tunable On-Chip Band-Pass Filter

    NARCIS (Netherlands)

    Ghaffari, A.; Klumperink, Eric A.M.; Nauta, Bram

    2010-01-01

    Abstract A passive switched capacitor RF band-pass filter with clock controlled center frequency is realized in 65nm CMOS. An off-chip transformer which acts as a balun, improves filter-Q and realizes impedance matching. The differential architecture reduces clock-leakage and suppresses selectivity

  20. A novel 2nd-order bandpass MFSS filter with miniaturized structure

    Directory of Open Access Journals (Sweden)

    C. Y. Fang

    2015-08-01

    Full Text Available In order to effectively obtain a miniaturized structure and good filtering properties, we propose a novel 2nd-order bandpass metamaterial frequency selective surface (MFSS filter which contains two capacitive layers and one inductive layer, where there are multi-loop metallic patches as shunt capacitor C and planar wire grids as series inductor L respectively. Unlike the traditional operation way—the tuned elements used in resonant surface approximately equal to one wavelength in circumference and the structure thickness with a spacing of a quarter wavelength apart, by changing the value of L and C and matching multilayer dielectric to adjust the LC coupling resonance and the resonance impedance respectively, the proposed MFSS filter can achieves a miniatured structure with ideal bandpass properties. Measurement results of the fabricated prototype of the bandpass filter (BPF indicate that the dimension of the tuned element on resonant surface is approximately 0.025 wavelength, i.e., 0.025λ. At the same time, the filter has the stable center frequency of f0 = 1.53GHz and the transmittance of T ⩾ 96.3% and high Q-value for the TE/TM wave polarization at various incidence angles. The novel 2nd-order bandpass MFSS filter with miniaturized structure not only can decrease structure dimension, but also has a wide range of applications to microwave and infrared band.

  1. Optimization of band-pass filtering parameters of a Raman lidar detecting atmospheric water vapor

    International Nuclear Information System (INIS)

    Cao, Kai-Fa; Hu, Shun-Xing; Wang, Ying-jian

    2012-01-01

    It is very important for daytime Raman lidar measurement of water vapor to determine the parameters of a band-pass filter, which are pertinent to the lidar signal to noise ratio (SNR). The simulated annealing (SA) algorithm method has an advantage in finding the extremum of a certain cost function. In this paper, the Raman spectrum of water vapor is simulated and then a first realization of a simulated annealing algorithm in the optimization of a band-pass filter of a Raman lidar system designed to detect daytime water vapor is presented. The simulated results indicate that the narrow band-pass filter has higher SNR than the wide filter does but there would be an increase in the temperature sensitivity of a narrowband Raman water vapor lidar in the upper troposphere. The numerical simulation indicates that the magnitude of the temperature dependent effect can reach 3.5% or more for narrow band-pass Raman water vapor measurements so it is necessary to consider a new water vapor Raman lidar equation that permits the temperature sensitivity of these equations to be confined to a single term. (paper)

  2. Noise-Coupled Image Rejection Architecture of Complex Bandpass ΔΣAD Modulator

    Science.gov (United States)

    San, Hao; Kobayashi, Haruo

    This paper proposes a new realization technique of image rejection function by noise-coupling architecture, which is used for a complex bandpass ΔΣAD modulator. The complex bandpass ΔΣAD modulator processes just input I and Q signals, not image signals, and the AD conversion can be realized with low power dissipation. It realizes an asymmetric noise-shaped spectra, which is desirable for such low-IF receiver applications. However, the performance of the complex bandpass ΔΣAD modulator suffers from the mismatch between internal analog I and Q paths. I/Q path mismatch causes an image signal, and the quantization noise of the mirror image band aliases into the desired signal band, which degrades the SQNDR (Signal to Quantization Noise and Distortion Ratio) of the modulator. In our proposed modulator architecture, an extra notch for image rejection is realized by noise-coupled topology. We just add some passive capacitors and switches to the modulator; the additional integrator circuit composed of an operational amplifier in the conventional image rejection realization is not necessary. Therefore, the performance of the complex modulator can be effectively raised without additional power dissipation. We have performed simulation with MATLAB to confirm the validity of the proposed architecture. The simulation results show that the proposed architecture can achieve the realization of image-rejection effectively, and improve the SQNDR of the complex bandpass ΔΣAD modulator.

  3. All-optical OFDM demultiplexing by spectral magnification and optical band-pass filtering

    DEFF Research Database (Denmark)

    Palushani, Evarist; Mulvad, Hans Christian Hansen; Kong, Deming

    2013-01-01

    We propose spectral magnification of optical-OFDM super-channels using time-lenses, enabling reduced inter-carrier-interference in subcarrier detection by simple band-pass filtering. A demonstration on an emulated 100 Gbit/s DPSK optical-OFDM channel shows improved sensitivities after 4-times spe...

  4. Lean Six Sigma in financial services

    OpenAIRE

    de Koning, H.; Does, R.J.M.M.; Bisgaard, S.

    2008-01-01

    Lean Thinking and Six Sigma are typically considered as separate approaches to process innovation, with complementary strengths. When combined as Lean Six Sigma, this approach provides a unified framework for systematically developing innovations. Lean Six Sigma can also bring about significant results and breakthrough improvements in financial services, as demonstrated with four case studies from Dutch multinational insurance companies. These cases demonstrate the importance of incremental i...

  5. Cohomological reduction of sigma models

    Energy Technology Data Exchange (ETDEWEB)

    Candu, Constantin; Mitev, Vladimir; Schomerus, Volker [DESY, Hamburg (Germany). Theory Group; Creutzig, Thomas [North Carolina Univ., Chapel Hill, NC (United States). Dept. of Physics and Astronomy

    2010-01-15

    This article studies some features of quantum field theories with internal supersymmetry, focusing mainly on 2-dimensional non-linear sigma models which take values in a coset superspace. It is discussed how BRST operators from the target space super- symmetry algebra can be used to identify subsectors which are often simpler than the original model and may allow for an explicit computation of correlation functions. After an extensive discussion of the general reduction scheme, we present a number of interesting examples, including symmetric superspaces G/G{sup Z{sub 2}} and coset superspaces of the form G/G{sup Z{sub 4}}. (orig.)

  6. A 8X Oversampling Ratio, 14bit, 5-MSamples/s Cascade 3-1 Sigma-delta Modulator

    Directory of Open Access Journals (Sweden)

    Y. Yin

    2005-01-01

    Full Text Available A 14-b, 5-MHz output-rate cascaded 3-1 sigma-delta analog-to-digital converters (ADC has been developed for broadband communication applications, and a novel 4th-order noise-shaping is obtained by using the proposed architecture. At a low oversampling ratio (OSR of 8, the ADC achieves 91.5dB signal-to-quantization ratio (SQNR, in contrast to 71.8dB of traditional 2-1-1 cascaded sigma-delta ADC in 2.5-MHz bandwidth and over 80dB signal-to-noise and distortion (SINAD even under assumptions of awful circuit non-idealities and opamp non-linearity. The proposed architecture can potentially operates at much more high frequencies with scaled IC technology, to expand the analog-to-digital conversion rate for high-resolution applications.

  7. Comparative Analysis between Lean, Six Sigma and Lean Six Sigma Concepts

    Directory of Open Access Journals (Sweden)

    Alexandra Mirela Cristina MUNTEANU

    2017-06-01

    Full Text Available This paper analyzes the benefits of Lean Six Sigma in comparison with Lean and Six Sigma, traditional improvement methodologies. The introduction highlights the appearance of Lean Six Sigma, early 2000s, as well as the benefits brought by the integrated approach. The following parts of the study emphasize the main differences between methodologies and their commonalities based on their synergy. Finally the advantages of Lean Six Sigma versus Lean and Six Sigma are analyzed and systematized by author in order to reveal Lean Six Sigma’s benefits.

  8. De praktijk van Lean Six Sigma

    NARCIS (Netherlands)

    Does, R.J.M.M.; de Koning, H.

    2008-01-01

    Zowel Lean als Six Sigma zijn benaderingen van kwaliteits- en efficiëntieverbetering die op dit moment sterk in de belangstelling staan van zowel de industrie als de dienstverlening. Lean Six Sigma integreert beide benaderingen. Ze wordt door sommigen gezien als panacee voor alle mogelijke

  9. Six Sigma: blauwdruk voor de kenniseconomie.

    NARCIS (Netherlands)

    Does, R.J.M.M.; de Mast, J.

    2005-01-01

    Abstract Six Sigma is zo langzamerhand een niet weg te denken programma voor kwaliteits- en efficiencyverbeteringen. Het heeft met name voor enorme successen gezorgd in productiebedrijven. Six Sigma ligt ook onder vuur: het zou een trend zijn die voorbij gaat. De auteurs van dit artikel zijn het van

  10. Six Sigma als blauwdruk voor de kenniseconomie.

    NARCIS (Netherlands)

    de Mast, J.; Does, R.J.M.M.

    2005-01-01

    Abstract Six Sigma is zo langzamerhand een niet weg te denken programma voor kwaliteits- en efficiencyverbeteringen. Het heeft met name voor enorme successen gezorgd in productiebedrijven. Six Sigma ligt ook onder vuur: het zou een trend zijn die voorbij gaat. De auteurs van dit artikel zijn het van

  11. Some examples of instantons in sigma models

    International Nuclear Information System (INIS)

    Kogan, Ya.I.; Markushevich, D.G.; Morozov, A.Yu.; Ol'shanetskii, M.A.; Perelomov, A.M.; Roslyi, A.A.

    1989-01-01

    The paper considers (supersymmetric) sigma models in which the fields are defined on a Riemann surface of genus p and take values on a Kaehlerian manifold. Some mathematical methods for finding instantons and their zero modes in such sigma models are explained. Only holomorphic instantons are considered

  12. Sigma meson in heavy ion collision

    International Nuclear Information System (INIS)

    Cristian, Ivan; Fuchs, Christian

    2004-01-01

    We want to present a short theoretical prediction of the behaviour of the sigma meson in heavy ion collisions. It is considered that the sigma meson is a pion-pion correlation, resulting from the decay of the N*(1440) resonance. There will be presented some QMD simulations. (authors)

  13. Lean Six Sigma in a hospital

    NARCIS (Netherlands)

    van den Heuvel, J.; Does, R.J.M.M.; de Koning, H.

    2006-01-01

    Abstract Hospitals today face major challenges. Patients demand quality of care to be improved continuously. Health insurance companies demand the lowest possible prices. Lean Six Sigma is a program that can help healthcare providers to achieve these (seemingly) conflicting goals. Lean Six Sigma is

  14. Integrating the Many Facets of Six Sigma

    NARCIS (Netherlands)

    de Mast, J.

    2007-01-01

    We seek to provide a unified characterization of Six Sigma by studying the phenomenon from the perspectives of business economics, organizational theory, competitive strategy and industrial statistics, and we pinpoint its core methodological principles. We describe Six Sigma as a prescriptive

  15. THE LEAN AND SIX SIGMA SINERGY

    Directory of Open Access Journals (Sweden)

    Mirko Sokovic

    2008-12-01

    Full Text Available Many organizations, dealing with continuous improvement methods, have realized that Lean and Six Sigma methodologies complement each other. Lean manufacturing focuses on the remova l of waste so that all processes in the total system add value from the customers' perspectives. The main emphasis of Six Sigma is the application of statistical tools in a disciplined manner, which requires data-driven decision-making. The integration of Lean and Six Sigma provides a synergetic effect, a rapid process improvement strategy for attaining organizational goals. When separated, Lean manufacturing cannot bring a process under statistical control, and Six Sigma cannot dramatically improve cycle time or reduce invested capital. Together, synergistic qualities are created to maximize the potential for a process improvement. The paper deals with Lean and Six Sigma principles and approaches used in modern manufacturing for process improvements, and bring forward benefits that are gained when these two methodologies are integrated.

  16. Electromagnetic radiation-2450 MHz exposure causes cognition ...

    Indian Academy of Sciences (India)

    83

    Electromagnetic radiation-2450 MHz exposure causes cognition deficit with mitochondrial. 1 ... decrease in levels of acetylcholine, and increase in activity of acetyl ...... neuronal apoptosis and cognitive disturbances in sevoflurane or propofol ...

  17. TA-55 and Sigma Overview

    Energy Technology Data Exchange (ETDEWEB)

    Spearing, Dane Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Safeguards Science and Technology Group (NEN-1)

    2016-11-29

    These are slides from a facility overview presentation for visiting agencies to Los Alamos National Laboratory (LANL). The TA-55 Plutonium Facility (PF-4) is discussed in detail. PF-4 is a unique resource for US plutonium programs. The basic design is flexible and has adapted to changing national needs. It is a robust facility with strong safety and security implementation. It supports a variety of national programs. It will continue for many years into the future. Sigma is then discussed in detail, which handles everything from hydrogen to uranium. It has been in long term service to the Nation (nearly 60 years). It has a flexible authorization basis to handle almost the entire periodic table. It has a wide breadth of prototyping and characterization capabilities. It has integrated program and line management.

  18. Nonabelian Gauged Linear Sigma Model

    Institute of Scientific and Technical Information of China (English)

    Yongbin RUAN

    2017-01-01

    The gauged linear sigma model (GLSM for short) is a 2d quantum field theory introduced by Witten twenty years ago.Since then,it has been investigated extensively in physics by Hori and others.Recently,an algebro-geometric theory (for both abelian and nonabelian GLSMs) was developed by the author and his collaborators so that he can start to rigorously compute its invariants and check against physical predications.The abelian GLSM was relatively better understood and is the focus of current mathematical investigation.In this article,the author would like to look over the horizon and consider the nonabelian GLSM.The nonabelian case possesses some new features unavailable to the abelian GLSM.To aid the future mathematical development,the author surveys some of the key problems inspired by physics in the nonabelian GLSM.

  19. Providing primary standard calibrations beyond 20 MHz

    International Nuclear Information System (INIS)

    Bickley, C J; Zeqiri, B; Robinson, S P

    2004-01-01

    The number of applications of medical ultrasound utilising frequencies in excess of 20 MHz has shown a consistent increase over recent years. Coupled with the commercial availability of wide-bandwidth hydrophones whose response extends beyond 40 MHz, this has driven a growing need to develop hydrophone calibration techniques at elevated frequencies. The current National Physical Laboratory primary standard method of calibrating hydrophones is based on an optical interferometer. This has been in operation for around 20 years and provides traceability over the frequency range of 0.3 to 20 MHz. More recently, calibrations carried out using the interferometer have been extended to 60 MHz, although the uncertainties associated with these calibrations are poor, being in excess of ±20% at high frequencies. Major contributions to the degraded calibration uncertainties arise from poor signal-to-noise at higher frequencies, the frequency response of the photodiodes used and the noise floor of the instrument. To improve the uncertainty of hydrophone calibrations above 20 MHz, it has been necessary to build and commission a new interferometer. Important features of the new primary standard are its use of a higher power laser to improve the signal-to-noise ratio, along with photodiodes whose greater bandwidth to improve the overall frequency response. This paper describes the design of key aspects of the new interferometer. It also presents some initial results of the performance assessment, including a detailed comparison of calibrations of NPL reference membrane hydrophones, undertaken using old and new interferometers for calibration up to 40 MHz

  20. Multiple plasmonically induced transparency for chip-scale bandpass filters in metallic nanowaveguides

    Science.gov (United States)

    Lu, Hua; Yue, Zengqi; Zhao, Jianlin

    2018-05-01

    We propose and investigate a new kind of bandpass filters based on the plasmonically induced transparency (PIT) effect in a special metal-insulator-metal (MIM) waveguide system. The finite element method (FEM) simulations illustrate that the obvious PIT response can be generated in the metallic nanostructure with the stub and coupled cavities. The lineshape and position of the PIT peak are particularly dependent on the lengths of the stub and coupled cavities, the waveguide width, as well as the coupling distance between the stub and coupled cavities. The numerical simulations are in accordance with the results obtained by the temporal coupled-mode theory. The multi-peak PIT effect can be achieved by integrating multiple coupled cavities into the plasmonic waveguide. This PIT response contributes to the flexible realization of chip-scale multi-channel bandpass filters, which could find crucial applications in highly integrated optical circuits for signal processing.

  1. Tunable high-channel-count bandpass plasmonic filters based on an analogue of electromagnetically induced transparency

    International Nuclear Information System (INIS)

    Lu Hua; Liu Xueming; Wang Guoxi; Mao Dong

    2012-01-01

    We have proposed a novel type of bandpass plasmonic filter consisting of metal–insulator–metal bus waveguides coupled with a series of side-coupled cavities and stub waveguides. The theoretical modeling demonstrates that our waveguide-resonator system performs a plasmonic analogue of electromagnetically induced transparency (EIT) in atomic systems, as is confirmed by numerical experiments. The plasmonic EIT-like response enables the realization of nanoscale bandpass filters with multiple channels. Additionally, the operating wavelengths and bandwidths of our filters can be efficiently tuned by adjusting the geometric parameters such as the lengths of stub waveguides and the coupling distances between the cavities and stub waveguides. The ultracompact configurations contribute to the achievement of wavelength division multiplexing systems for optical computing and communications in highly integrated optical circuits. (paper)

  2. Neural Model for Left-Handed CPW Bandpass Filter Loaded Split Ring Resonator

    Science.gov (United States)

    Liu, Haiwen; Wang, Shuxin; Tan, Mingtao; Zhang, Qijun

    2010-02-01

    Compact left-handed coplanar waveguide (CPW) bandpass filter loaded split ring resonator (SRR) is presented in this paper. The proposed filter exhibits a quasi-elliptic function response and its circuit size occupies only 12 × 11.8 mm2 (≈0.21 λg × 0.20 λg). Also, a simple circuit model is given and the parametric study of this filter is discussed. Then, with the aid of NeuroModeler software, a five-layer feed-forward perceptron neural networks model is built up to optimize the proposed filter design fast and accurately. Finally, this newly left-handed CPW bandpass filter was fabricated and measured. A good agreement between simulations and measurement verifies the proposed left-handed filter and the validity of design methodology.

  3. A Compact Band-Pass Filter with High Selectivity and Second Harmonic Suppression.

    Science.gov (United States)

    Hadarig, Ramona Cosmina; de Cos Gomez, Maria Elena; Las-Heras, Fernando

    2013-12-03

    The design of a novel band-pass filter with narrow-band features based on an electromagnetic resonator at 6.4 GHz is presented. A prototype is manufactured and characterized in terms of transmission and reflection coefficient. The selective passband and suppression of the second harmonic make the filter suitable to be used in a C band frequency range for radar systems and satellite/terrestrial applications. To avoid substantial interference for this kind of applications, passive components with narrow band features and small dimensions are required. Between 3.6 GHz and 4.2 GHz the band-pass filter with harmonic suppression should have an attenuation of at least 35 dB, whereas for a passband, less than 10% is sufficient.

  4. UWB Bandpass Filter with Ultra-wide Stopband based on Ring Resonator

    Science.gov (United States)

    Kazemi, Maryam; Lotfi, Saeedeh; Siahkamari, Hesam; Mohammadpanah, Mahmood

    2018-04-01

    An ultra-wideband (UWB) bandpass filter with ultra-wide stopband based on a rectangular ring resonator is presented. The filter is designed for the operational frequency band from 4.10 GHz to 10.80 GHz with an ultra-wide stopband from 11.23 GHz to 40 GHz. The even and odd equivalent circuits are used to achieve a suitable analysis of the proposed filter performance. To verify the design and analysis, the proposed bandpass filter is simulated using full-wave EM simulator Advanced Design System and fabricated on a 20mil thick Rogers_RO4003 substrate with relative permittivity of 3.38 and a loss tangent of 0.0021. The proposed filter behavior is investigated and simulation results are in good agreement with measurement results.

  5. Retinal blood vessel extraction using tunable bandpass filter and fuzzy conditional entropy.

    Science.gov (United States)

    Sil Kar, Sudeshna; Maity, Santi P

    2016-09-01

    Extraction of blood vessels on retinal images plays a significant role for screening of different opthalmologic diseases. However, accurate extraction of the entire and individual type of vessel silhouette from the noisy images with poorly illuminated background is a complicated task. To this aim, an integrated system design platform is suggested in this work for vessel extraction using a sequential bandpass filter followed by fuzzy conditional entropy maximization on matched filter response. At first noise is eliminated from the image under consideration through curvelet based denoising. To include the fine details and the relatively less thick vessel structures, the image is passed through a bank of sequential bandpass filter structure optimized for contrast enhancement. Fuzzy conditional entropy on matched filter response is then maximized to find the set of multiple optimal thresholds to extract the different types of vessel silhouettes from the background. Differential Evolution algorithm is used to determine the optimal gain in bandpass filter and the combination of the fuzzy parameters. Using the multiple thresholds, retinal image is classified as the thick, the medium and the thin vessels including neovascularization. Performance evaluated on different publicly available retinal image databases shows that the proposed method is very efficient in identifying the diverse types of vessels. Proposed method is also efficient in extracting the abnormal and the thin blood vessels in pathological retinal images. The average values of true positive rate, false positive rate and accuracy offered by the method is 76.32%, 1.99% and 96.28%, respectively for the DRIVE database and 72.82%, 2.6% and 96.16%, respectively for the STARE database. Simulation results demonstrate that the proposed method outperforms the existing methods in detecting the various types of vessels and the neovascularization structures. The combination of curvelet transform and tunable bandpass

  6. Spectral and Wavefront Error Performance of WFIRST-AFTA Bandpass Filter Coating Prototypes

    Science.gov (United States)

    Quijada, Manuel A.; Seide, Laurie; Pasquale, Bert A.; McMann, Joseph C.; Hagopian, John G.; Dominguez, Margaret Z.; Gong, Quian; Marx, Catherine T.

    2016-01-01

    The Cycle 5 design baseline for the Wide-Field Infrared Survey Telescope Astrophysics Focused Telescope Assets (WFIRST/AFTA) instrument includes a single wide-field channel (WFC) instrument for both imaging and slit-less spectroscopy. The only routinely moving part during scientific observations for this wide-field channel is the element wheel (EW) assembly. This filter-wheel assembly will have 8 positions that will be populated with 6 bandpass filters, a blank position, and a Grism that will consist of a three-element assembly to disperse the full field with an undeviated central wavelength for galaxy redshift surveys. All filter elements in the EW assembly will be made out of fused silica substrates (110 mm diameter) that will have the appropriate bandpass coatings according to the filter designations (Z087, Y106, J129, H158, F184, W149 and Grism). This paper presents and discusses the performance (including spectral transmission and reflected/transmitted wavefront error measurements) of a subset of bandpass filter coating prototypes that are based on the WFC instrument filter compliment. The bandpass coating prototypes that are tested in this effort correspond to the Z087, W149, and Grism filter elements. These filter coatings have been procured from three different vendors to assess the most challenging aspects in terms of the in-band throughput, out of band rejection (including the cut-on and cutoff slopes), and the impact the wavefront error distortions of these filter coatings will have on the imaging performance of the wide-field channel in the WFIRST/AFTA observatory.

  7. All-optical OFDM demultiplexing by spectral magnification and band-pass filtering.

    Science.gov (United States)

    Palushani, E; Mulvad, H C Hansen; Kong, D; Guan, P; Galili, M; Oxenløwe, L K

    2014-01-13

    We propose a simple OFDM receiver allowing for the use of standard WDM receivers to receive spectrally advanced OFDM signals. We propose to spectrally magnify the optical-OFDM super-channels using a spectral telescope consisting of two time-lenses, which enables reduced inter-carrier-interference in subcarrier detection by simple band-pass filtering. A demonstration on an emulated 100 Gbit/s DPSK optical-OFDM channel shows improved sensitivities after 4-times spectral magnification.

  8. On the optimal sampling of bandpass measurement signals through data acquisition systems

    International Nuclear Information System (INIS)

    Angrisani, L; Vadursi, M

    2008-01-01

    Data acquisition systems (DAS) play a fundamental role in a lot of modern measurement solutions. One of the parameters characterizing a DAS is its maximum sample rate, which imposes constraints on the signals that can be alias-free digitized. Bandpass sampling theory singles out separated ranges of admissible sample rates, which can be significantly lower than carrier frequency. But, how to choose the most convenient sample rate according to the purpose at hand? The paper proposes a method for the automatic selection of the optimal sample rate in measurement applications involving bandpass signals; the effects of sample clock instability and limited resolution are also taken into account. The method allows the user to choose the location of spectral replicas of the sampled signal in terms of normalized frequency, and the minimum guard band between replicas, thus introducing a feature that no DAS currently available on the market seems to offer. A number of experimental tests on bandpass digitally modulated signals are carried out to assess the concurrence of the obtained central frequency with the expected one

  9. The acetone bandpass detector for inverse photoemission: operation in proportional and Geiger–Müller modes

    Science.gov (United States)

    Thiede, Christian; Niehues, Iris; Schmidt, Anke B.; Donath, Markus

    2018-06-01

    Inverse photoemission is the most versatile experimental tool to study the unoccupied electronic structure at surfaces of solids. Typically, the experiments are performed in the isochromat mode with bandpass photon detectors. For gas-filled counters, the bandpass behavior is realized by the combination of the photoionization threshold of the counting gas as the high-pass filter and the ultraviolet transmission cutoff of an alkaline earth fluoride entrance window as the low-pass filter. The transmission characteristics of the entrance window determine the optical bandpass. The performance of the counter depends on the composition of the detection gas and the fill-gas pressure, the readout electronics and the counter geometry. For the well-known combination of acetone and CaF2, the detector can be operated in proportional and Geiger–Müller modes. In this work, we review aspects concerning the working principles, the counter construction and the read-out electronics. We identify optimum working parameters and provide a step-by-step recipe how to build, install and operate the device.

  10. Lean Six Sigma implementation and organizational culture.

    Science.gov (United States)

    Knapp, Susan

    2015-01-01

    The purpose of this paper is to examine the relationship between four organizational cultural types defined by the Competing Values Framework and three Lean Six Sigma implementation components - management involvement, use of Lean Six Sigma methods and Lean Six Sigma infrastructure. The study involved surveying 446 human resource and quality managers from 223 hospitals located in Maine, New Hampshire, Vermont, Massachusetts and Rhode Island using the Organizational Culture Assessment Instrument. Findings - In total, 104 completed responses were received and analyzed using multivariate analysis of variance. Follow-up analysis of variances showed management support was significant, F(3, 100)=4.89, p cultures having significant interactions with management support. The relationship between organizational culture and Lean Six Sigma in hospitals provides information on how specific cultural characteristics impact the Lean Six Sigma initiative key components. This information assists hospital staff who are considering implementing quality initiatives by providing an understanding of what cultural values correspond to effective Lean Six Sigma implementation. Managers understanding the quality initiative cultural underpinnings, are attentive to the culture-shared values and norm's influence can utilize strategies to better implement Lean Six Sigma.

  11. Ultra-narrow bandpass filters for long range optical telecommunications at 1064nm and 1550nm, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Ultra-narrow bandpass filters with high off-band rejection are needed to maximize signal to noise for free space communications. Omega Optical is developing NIR...

  12. SIGMA WEB INTERFACE FOR REACTOR DATA APPLICATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Pritychenko,B.; Sonzogni, A.A.

    2010-05-09

    We present Sigma Web interface which provides user-friendly access for online analysis and plotting of the evaluated and experimental nuclear reaction data stored in the ENDF-6 and EXFOR formats. The interface includes advanced browsing and search capabilities, interactive plots of cross sections, angular distributions and spectra, nubars, comparisons between evaluated and experimental data, computations for cross section data sets, pre-calculated integral quantities, neutron cross section uncertainties plots and visualization of covariance matrices. Sigma is publicly available at the National Nuclear Data Center website at http://www.nndc.bnl.gov/sigma.

  13. Sigma Web Interface For Reactor Data Applications

    International Nuclear Information System (INIS)

    Pritychenko, B.; Sonzogni, A.A.

    2010-01-01

    We present Sigma Web interface which provides user-friendly access for online analysis and plotting of the evaluated and experimental nuclear reaction data stored in the ENDF-6 and EXFOR formats. The interface includes advanced browsing and search capabilities, interactive plots of cross sections, angular distributions and spectra, nubars, comparisons between evaluated and experimental data, computations for cross section data sets, pre-calculated integral quantities, neutron cross section uncertainties plots and visualization of covariance matrices. Sigma is publicly available at the National Nuclear Data Center website at http://www.nndc.bnl.gov/sigma.

  14. IDENTIFICATION AND SELECTION OF SIX SIGMA PROJECTS

    Directory of Open Access Journals (Sweden)

    Abdalhkeim FA. Flifel

    2017-04-01

    Full Text Available Six Sigma is a well-structured and proven methodology for improving organizational performance. It helps achieving the goals of the organization through the use of project-driven approach. The implementation of Six sigma approach depends on proper identification and selection of projects, moreover, the selection of right Six sigma projects is one of the critical success factors of six sigma efforts. The paper provides the sources for the identification of potential projects, top down and bottom up approaches, the process of selection of projects, guidelines that assist the selection of appropriate projects, selection criteria which must be precisely chosen in accordance with the objectives, needs and capabilities of the organization as well as sophisticated techniques and tools recommended in the literature for the selection of projects.

  15. Evidence for the decay sigma+ --> pmu+ mu-.

    Science.gov (United States)

    Park, H K; Burnstein, R A; Chakravorty, A; Chen, Y C; Choong, W S; Clark, K; Dukes, E C; Durandet, C; Felix, J; Fu, Y; Gidal, G; Gustafson, H R; Holmstrom, T; Huang, M; James, C; Jenkins, C M; Jones, T; Kaplan, D M; Lederman, L M; Leros, N; Longo, M J; Lopez, F; Lu, L C; Luebke, W; Luk, K B; Nelson, K S; Perroud, J-P; Rajaram, D; Rubin, H A; Volk, J; White, C G; White, S L; Zyla, P

    2005-01-21

    We report the first evidence for the decay Sigma(+)-->pmu(+)mu(-) from data taken by the HyperCP (E871) experiment at Fermilab. Based on three observed events, the branching ratio is B(Sigma(+)-->pmu(+)mu(-))=[8.6(+6.6)(-5.4)(stat)+/-5.5(syst)]x10(-8). The narrow range of dimuon masses may indicate that the decay proceeds via a neutral intermediate state, Sigma(+)-->pP(0),P0-->mu(+)mu(-) with a P0 mass of 214.3+/-0.5 MeV/c(2) and branching ratio B(Sigma(+)-->pP(0),P0-->mu(+)mu(-))=[3.1(+2.4)(-1.9)(stat)+/-1.5(syst)]x10(-8).

  16. Lean six sigma application to transportation logistics

    Directory of Open Access Journals (Sweden)

    Simone Tavares Fernandes

    2012-06-01

    Full Text Available This work presents the application of Lean Six Sigma in a case study of a metallurgic industry. The Six Sigma and the Lean are two processes used by enterprises in Brazil and worldwide. Currently the integration of these processes is a challenge for these companies, which search a way more efficient to reduce their wastes and to adapt to the needs of their markets. The paper had as purpose to demonstrate the applicability of the Lean Six Sigma in a real logistical problem related to the transportation of goods among units of a metallurgic industry. The stages used for the solution of the problem follow the DMAIC cycle – Define, Measure, Analyze, Improve and Control. The paper presents in details the integrated approach of the improvement processes Lean and Six Sigma, their tools set, as well the excellent results obtained in the case study.

  17. Doubly graded sigma model with torsion

    International Nuclear Information System (INIS)

    Kowalski-Glikman, J.

    1986-08-01

    Using the Hull-Witten construction we show how to introduce torsion to the doubly graded sigma model. This construction enables us to find a link between this model and the ten-dimensional supergravity theory in superspace. (Auth.)

  18. Some examples of instantons in sigma models

    International Nuclear Information System (INIS)

    Kogan, Ya.; Markushevich, D.; Morozov, A.; Ol'shanetskya, M.; Perelomov, A.; Roslij, A.

    1988-01-01

    Instantons on some manifolds of type K3 are described. Zero modes in two-dimensional sigma models on such manifolds are counted. The necessary facts on K3 manifolds are exposed in monographs. Instanton configurations are described

  19. Pion--nucleon sigma-commutator

    International Nuclear Information System (INIS)

    Banerjee, M.K.; Cammarata, J.B.

    1977-07-01

    The reasons for the large discrepancies in the magnitude of the πN sigma-commutator, sigma(πN), obtained by several authors are discussed using dynamic theory of the πN scattering amplitude. With sigma(πN) approximately 25 MeV this theory reproduces reasonably well both the experimental S-wave phase shifts at low energies and the amplitudes C approximately/sup(+)/(ν=0,t less than or equal to 0) determined by Langbein. In the method of Cheng and Dashen the value of sigma(πN) is obtained from these amplitudes by extrapolation to t = 2m 2 /sub π/. A study of the experimental D-wave ''scattering lengths'' implies that the coefficient of the term quadratic in t in the Hoehler expansion of C approximately/sup(+)/(0,t) is negative. Adding such a term to the results of the S-wave theory will tend to improve the agreement for C approximately/sup (+)/(0,t less than or equal to 0). These results suggest that the large ''world value'' sigma(πN) = 65 +- 5 MeV obtained using the Cheng-Dashen method is a consequence of errors in the extrapolation of amplitudes to the unphysical point ν = 0, t = 2m 2 /sub π/. Only the smaller value sigma(πN) approximately 25 MeV appears to be consistent with the experimental data and theoretical constraints

  20. The six sigma program: an empirical study of brazilian companies.

    OpenAIRE

    Carvalho, Marly Monteiro de; Ho, Linda Lee; Pinto, Silvia Helena Boarin

    2014-01-01

    Purpose – The purpose of this paper is to assess the status of Six Sigma's status in Brazilian companies and understand the integration of this program with other quality management approaches. Additionally, the critical success factors (CSFs) for Six Sigma implementation and primary Six Sigma program characteristics were identified. Finally, the results of the used of Six Sigma were analysed. Design/methodology/approach – An extensive literature review illustrates the primary Six Sigma c...

  1. BLAZAR SPECTRAL PROPERTIES AT 74 MHz

    Energy Technology Data Exchange (ETDEWEB)

    Massaro, F.; Funk, S. [SLAC National Laboratory and Kavli Institute for Particle Astrophysics and Cosmology, 2575 Sand Hill Road, Menlo Park, CA 94025 (United States); Giroletti, M. [INAF Istituto di Radioastronomia, via Gobetti 101, I-40129 Bologna (Italy); Paggi, A.; D' Abrusco, R. [Harvard-Smithsonian Astrophysical Observatory, 60 Garden Street, Cambridge, MA 02138 (United States); Tosti, G. [Dipartimento di Fisica, Università degli Studi di Perugia, I-06123 Perugia (Italy)

    2013-10-01

    Blazars are the most extreme class of active galactic nuclei. Despite a previous investigation at 102 MHz for a small sample of BL Lac objects and our recent analysis of blazars detected in the Westerbork Northern Sky Survey, a systematic study of the blazar spectral properties at frequencies below 100 MHz has been never carried out. In this paper, we present the first analysis of the radio spectral behavior of blazars based on the recent Very Large Array Low-frequency Sky Survey (VLSS) at 74 MHz. We search for blazar counterparts in the VLSS catalog, confirming that they are detected at 74 MHz. We then show that blazars present radio-flat spectra (i.e., radio spectral indices of ∼0.5) when evaluated, which also about an order of magnitude in frequency lower than previous analyses. Finally, we discuss the implications of our findings in the context of the blazars-radio galaxies connection since the low-frequency radio data provide a new diagnostic tool to verify the expectations of the unification scenario for radio-loud active galaxies.

  2. Dense grid of narrow bandpass filters for the JST/T250 telescope: summary of results

    Science.gov (United States)

    Brauneck, Ulf; Sprengard, Ruediger; Bourquin, Sebastien; Marín-Franch, Antonio

    2018-01-01

    On the Javalambre mountain in Spain, the Centro de Estudios de Fisica del Cosmos de Aragon has setup two telescopes, the JST/T250 and the JAST/T80. The JAST/T80 telescope integrates T80Cam, a large format, single CCD camera while the JST/T250 will mount the JPCam instrument, a 1.2Gpix camera equipped with a 14-CCD mosaic using the new large format e2v 9.2k×9.2k 10-μm pixel detectors. Both T80Cam and JPCam integrate a large number of filters in dimensions of 106.8×106.8 mm2 and 101.7×95.5 mm2, respectively. For this instrument, SCHOTT manufactured 56 specially designed steep edged bandpass interference filters, which were recently completed. The filter set consists of bandpass filters in the range between 348.5 and 910 nm and a longpass filter at 915 nm. Most of the filters have full-width at half-maximum (FWHM) of 14.5 nm and a blocking between 250 and 1050 nm with optical density of OD5. Absorptive color glass substrates in combination with interference filters were used to minimize residual reflection in order to avoid ghost images. In spite of containing absorptive elements, the filters show the maximum possible transmission. This was achieved by using magnetron sputtering for the filter coating process. The most important requirement for the continuous photometric survey is the tight tolerancing of the central wavelengths and FWHM of the filters. This insures each bandpass has a defined overlap with its neighbors. A high image quality required a low transmitted wavefront error (<λ/4 locally and <λ/2 on the whole aperture), which was achieved even by combining two or three substrates. We report on the spectral and interferometric results measured on the whole set of filters.

  3. Hysteretic self-oscillating bandpass current mode control for Class D audio amplifiers driving capacitive transducers

    DEFF Research Database (Denmark)

    Nielsen, Dennis; Knott, Arnold; Andersen, Michael A. E.

    2013-01-01

    A hysteretic self-oscillating bandpass current mode control (BPCM) scheme for Class D audio amplifiers driving capacitive transducers are presented. The scheme provides excellent stability margins and low distortion over a wide range of operating conditions. Small-signal behavior of the amplifier...... the rules of electrostatics have been known as very interesting alternatives to the traditional inefficient electrodynamic transducers. When driving capacitive transducers from a Class D audio amplifier the high impedance nature of the load represents a key challenge. The BPCM control scheme ensures a flat...

  4. Nonlinear performance characterization in an eight-pole quasi-elliptic bandpass filter

    International Nuclear Information System (INIS)

    Mateu, J; Collado, C; Menendez, O; O'Callaghan, J M

    2004-01-01

    In this work we predict the nonlinear behaviour of an eight-pole quasi-elliptic bandpass high temperature superconducting (HTS) filter with an equivalent circuit extracted from intermodulation measurements performed at the centre of the filter passband. We present measurements that show that the equivalent circuit is able to predict the intermodulation products produced by the filter when driven by two in-band or out-of-band sinusoidal signals. Numerical techniques based on harmonic balance are used to extract the elements of the equivalent circuit and to simulate its nonlinear performance

  5. Highly chirped single-bandpass microwave photonic filter with reconfiguration capabilities.

    Science.gov (United States)

    Bolea, Mario; Mora, José; Ortega, Beatriz; Capmany, José

    2011-02-28

    We propose a novel photonic structure to implement a chirped single-bandpass microwave photonic filter based on the amplitude modulation of a broadband optical signal transmitted by a non-linear dispersive element and an interferometric system prior to balanced photodetection. A full reconfigurability of the filter is achieved since amplitude and phase responses can be independently controlled. We have experimentally demonstrated chirp values up to tens of ns/GHz, which is, as far as we know, one order of magnitude better than others achieved by electrical approaches and furthermore, without restrictions in terms of frequency tuning since a frequency operation range up to 40 GHz has been experimentally demonstrated.

  6. Six sigma quality for fuel manufacturing

    International Nuclear Information System (INIS)

    Gabbani, M.D.; Onderwater, T.

    1997-01-01

    It is widely recognized that operational performance in product manufacturing is largely determined by understanding and maintaining process capability. By definition, Six Sigma is a statistical unit of measure reflecting process capability that yields less' than 6.8 defects per million product produced. Statistically, this translates into obtaining a long term manufacturing process capability of ± 4.5 standard deviations about the mean within specification limits. The heart of the Six Sigma program developed by the Six Sigma Academy is what we refer to as the Breakthrough Strategy. This rigorous analytical methodology is the driving force in obtaining world class performance of Six Sigma. The methodology applies statistical and practical tools in resolving a problem or improving a product or process. The application of Six Sigma focuses on attacking process input variables (independent) rather than the output variables. Focusing on these independent variables (temperature, power, force, etc.) and the variation in the end product they create, enables us to get to the root of the problem rather than react to the symptoms of the problem. In this manner we prevent defects from occurring rather than inspecting and monitoring the product. Why the need for such an ambitious program? It is estimated that the cost of failure (rework, scrap, warranties, etc.) can be as high as 15% of sales for companies typically operating at 3-4 sigma. In achieving Six Sigma, costs of failure are typically less than 5%. The thought of reducing business costs while achieving the recognition of being our customer's premier choice provides enormous incentive to reach such status. (author)

  7. Correlation holography: imaging of atoms when sigma/sub inelastic//sup >>sigma/elastic

    International Nuclear Information System (INIS)

    Csonka, P.L.

    1979-01-01

    Atomic-scale resolution of details is possible with this method, even if protons interact with the atoms overwhelmingly inelastically, i.e. when sigma/sub inelastic/ >>sigma/sub elastic/. Observation of small objects is compatible with quantum mechanics even if the disturbance of the object caused by the observation process is arbitrarily small

  8. How the early sporulation sigma factor sigmaF delays the switch to late development in Bacillus subtilis.

    Science.gov (United States)

    Karmazyn-Campelli, Céline; Rhayat, Lamya; Carballido-López, Rut; Duperrier, Sandra; Frandsen, Niels; Stragier, Patrick

    2008-03-01

    Sporulation in Bacillus subtilis is a primitive differentiation process involving two cell types, the forespore and the mother cell. Each cell implements two successive transcription programmes controlled by specific sigma factors. We report that activity of sigma(G), the late forespore sigma factor, is kept in check by Gin, the product of csfB, a gene controlled by sigma(F), the early forespore sigma factor. Gin abolishes sigma(G) transcriptional activity when sigma(G) is artificially synthesized during growth, but has no effect on sigma(F). Gin interacts strongly with sigma(G) but not with sigma(F) in a yeast two-hybrid experiment. The absence of Gin allows sigma(G) to be active during sporulation independently of the mother-cell development to which it is normally coupled. Premature sigma(G) activity leads to the formation of slow-germinating spores, and complete deregulation of sigma(G) synthesis is lethal when combined with gin inactivation. Gin allows sigma(F) to delay the switch to the late forespore transcription programme by preventing sigma(G) to take over before the cell has reached a critical stage of development. A similar strategy, following a completely unrelated route, is used by the mother cell.

  9. Improved low-distortion sigma-delta ADC with DWA for WLAN standards

    Energy Technology Data Exchange (ETDEWEB)

    Li Di; Yang Yintang; Zhu Zhangming; Shi Lichun; Wu Xiaofeng; Wang Jiangan, E-mail: lidi2004@126.co [School of Microelectronics, Xidian University, Xi' an 710071 (China)

    2010-02-15

    An improved low distortion sigma-delta ADC (analog-to-digital converter) for wireless local area network standards is presented. A feed-forward MASH 2-2 multi-bit cascaded sigma-delta ADC is adopted; however, this work shows a much better performance than the ADCs which have been presented to date by adding a feedback factor in the second stage to improve the performance of the in-band SNDR (signal to noise and distortion ratio), using 4-bit ADCs in both stages to minimize the quantization noise. Data weighted averaging technology is therefore used to decrease the mismatch noise induced by the 4-bit DACs, which improves the SFDR (spurious free dynamic range) of the ADC. The modulator has been implemented by a 0.18 {mu}m CMOS process and operates at a single 1.8 V supply voltage. Experimental results show that for a 1.25 MHz - -6 dBFS input signal at 160 MHz sampling frequency, the improved ADC with all non-idealities considered achieves a peak SNDR of 80.9 dB and an SFDR of 87 dB, and the effective number of bits is 13.15 bits. (semiconductor integrated circuits)

  10. Sigma virus and mutation in Drosophila melanogaster

    International Nuclear Information System (INIS)

    Paquin, S.L.A.

    1977-01-01

    - The objectives of these experiments have been (1) to verify and evidence more fully the action of sigma in causing recessive lethal mutation on the X chromosome of Drosophila, both in the male and the female germ line; (2) to extend the study of sigma-induced recessive lethal mutation to the Drosophila autosomes; (3) to explore the possibility that this mutagenesis is site-directed; (4) to study the effects of sigma virus in conjunction with radiation in increasing non-disjunction and dominant lethality. The virus increases the rate of radiation-induced nondisjunction by altering meiotic chromosomal behavior. Percentage of non-disjunction with 500 rads of x-rays in the virus-free flies was 0.176, while in sigma-containing lines it was 0.333. With high doses of either x or neutron radiation, the presence of the virus enhances the frequency of dominant lethality. The difference is especially significant with the fast neutrons. The results indicate that sigma, and presumably other viruses, are indeed environmental mutagens and are, therefore, factors in the rate of background or spontaneous mutation

  11. Six Lessons We Learned Applying Six Sigma

    Science.gov (United States)

    Carroll, Napoleon; Casleton, Christa H.

    2005-01-01

    As Chief Financial Officer of Kennedy Space Center (KSC), I'm not only responsible for financial planning and accounting but also for building strong partnerships with the CFO customers, who include Space Shuttle and International Space Station operations as well all who manage the KSC Spaceport. My never ending goal is to design, manage and continuously improve our core business processes so that they deliver world class products and services to the CFO's customers. I became interested in Six Sigma as Christa Casleton (KSC's first Six Sigma Black belt) applied Six Sigma tools and methods to our Plan and Account for Travel Costs Process. Her analysis was fresh, innovative and thorough but, even more impressive, was her approach to ensure ongoing, continuous process improvement. Encouraged by the results, I launched two more process improvement initiatives aimed at applying Six Sigma principles to CFO processes that not only touch most of my employees but also have direct customer impact. As many of you know, Six Sigma is a measurement scale that compares the output of a process with customer requirements. That's straight forward, but demands that you not only understand your processes but also know your products and the critical customer requirements. The objective is to isolate and eliminate the causes of process variation so that the customer sees consistently high quality.

  12. Possible applications of the sigma delta digitizer in particle physics

    International Nuclear Information System (INIS)

    Hallgren, B.

    1991-01-01

    The sigma delta (ΣΔ) principle is an analog-to-digital conversion technique based on high-frequency sampling and low-pass filtering of the quantization noise. Resolution in time is exchanged for that in amplitude so as to avoid the difficulty of implementing complex precision analog circuits, in favour of digital circuits. The approach is attractive because it will make it possible to integrate complete channels of high resolution analog-to-digital converters and time digitizers in submicron digital VLSI technologies. Advantage is taken of the fact that the state-of-the-art VLSI is better suited for providing fast digital circuits than for providing precise analog circuits. This article describes the principle and the performance of the ideal ΣΔ digitizer. The design and measurements of a new 10 MHz prototype circuit of a second-order ΣΔ is presented to show the high speed operation of such a circuit. The expected performance of a CMOS test design using the same principles is discussed. Digital filters, useful for particle physics, are introduced. A comparison to other digitizing techniques is made and the potential applications of the ΣΔ digitizer in particle physics are outlined. (orig.)

  13. VHDL Implementation of Sigma-Delta Analog To Digital Converter

    Science.gov (United States)

    Chavan, R. N.; Chougule, D. G.

    2010-11-01

    Sigma-Delta modulation techniques provide a range of opportunities in a signal processing system for both increasing performance and data path optimization along the silicon area axis in the design space. One of the most challenging tasks in Analog to Digital Converter (ADC) design is to adapt the circuitry to ever new CMOS process technology. For digital circuits the number of gates per square mm app. doubles per chip generation. Integration of analog parts in newer deep submicron technologies is much more tough and additionally complicated because the usable voltage ranges are decreasing with every new integration step. This paper shows an approach which only uses 2 resistors and 1 capacitor which are located outside a pure digital chip. So all integration advantages of pure digital chips are preserved, there is no design effort for a new chip generation and the ADC also can be used for FPGAs. Resolutions of up to 16 bit are achievable. Sample rates in the 1 MHz region are feasible so that the approach is also useful for ADCs for xDSL technologies.

  14. Design of doubly focusing, tunable (5 to 30 keV), wide-bandpass optics made from layered synthetic microstructures

    International Nuclear Information System (INIS)

    Bilderback, D.H.; Lairson, B.M.; Barbee, T.W. Jr.; Ice, G.E.; Sparks, C.J. Jr.

    1982-01-01

    Layered Synthetic Microstructures (LSMs) show great promise as focusing, high-throughput, hard x-ray monochromators. Experimental reflectivity vs. energy curves have been obtained on carbon-tungsten and carbon-molybdenum LSMs of up to 260 layers in thickness. Reflectivities for three flat LSMs with different bandpasses were 70% with δE/E = 5.4%, 66% with δE/E = 1.4%, and 19% with δE/E = 0.6%. A new generation of variable bandwidth optics using two successive LSMs is proposed. The first element will be an LSM deposited on a substrate that can be water cooled as it intercepts direct radiation from a storage ring. It can be bent for vertical focusing. The bandpass can be adjusted by choosing interchangeable first elements from an assortment of LSM's with different bandpasses (for example, δE/E = 0.005, 0.01, 0.02, 0.05, 0.1). The second LSM will consist of a multilayered structure with a 10% bandpass built onto a flexible substrate that can be bent for sagittal focusing. The result will be double focusing optics with an adjustable energy bandpass that are tunable from 5 to 30 keV

  15. Reduced size dual band pass filters for RFID applications with excellent bandpass/bandstop characteristics

    Science.gov (United States)

    Abdalla, M. A.; Choudhary, D. Kumar; Chaudhary, R. Kumar

    2018-02-01

    This paper presents the design of two reduced size dual-band metamaterial bandpass filters and its simulation followed by measurements of proposed filters. These filters are supporting different frequency bands and primarily could be utilize in radio frequency identification (RFID) application. The filter includes three cells in which two are symmetrical and both inductively coupled with the third cell which is present in between them. In the proposed designs, three different metamaterial composite right/left handed (CRLH) cell resonators have been analysed for compactness. The CRLH cell consists of an interdigital capacitor, a stub/meander line/spiral inductor and a via to connect the top of the structure and ground plane. Finally, the proposed dual band bandpass filters (using meander line and spiral inductor) are showing size reduction by 65% and 50% (with 25% operating frequency reduction), respectively, in comparison with reference filter using stub inductor. More than 30 dB attenuation has been achieved between the two passbands.

  16. Design and Implementation of Decimation Filter for 13-bit Sigma-Delta ADC Based on FPGA

    Directory of Open Access Journals (Sweden)

    Khalid Khaleel Mohammed

    2016-10-01

    Full Text Available A 13 bit Sigma-Delta ADC for a signal band of 40K Hz is designed in MATLAB Simulink and then implemented using Xilinx system generator tool.  The first order Sigma-Delta modulator is designed to work at a signal band of 40 KHz at an oversampling ratio (OSR of 256 with a sampling frequency of 20.48 MHz. The proposed decimation filter design is consists of a second order Cascaded Integrator Comb filter (CIC followed by two finite impulse response (FIR filters. This architecture reduces the need for multiplication which is need very large area. This architecture implements a decimation ratio of 256 and allows a maximum resolution of 13  bits in the output of the filter. The decimation filter was designed  and  tested  in  Xilinx  system  generator  tool  which  reduces  the  design  cycle  by  directly generating efficient VHDL code. The results obtained show that the overall Sigma-Delta ADC is able to achieve an ENOB (Effective Number Of Bit of 13.71 bits and SNR of 84.3 dB

  17. Sigma-2 receptor ligands QSAR model dataset

    Directory of Open Access Journals (Sweden)

    Antonio Rescifina

    2017-08-01

    Full Text Available The data have been obtained from the Sigma-2 Receptor Selective Ligands Database (S2RSLDB and refined according to the QSAR requirements. These data provide information about a set of 548 Sigma-2 (σ2 receptor ligands selective over Sigma-1 (σ1 receptor. The development of the QSAR model has been undertaken with the use of CORAL software using SMILES, molecular graphs and hybrid descriptors (SMILES and graph together. Data here reported include the regression for σ2 receptor pKi QSAR models. The QSAR model was also employed to predict the σ2 receptor pKi values of the FDA approved drugs that are herewith included.

  18. LEAN SIX SIGMA – MULTIPLE CASE STUDY

    Directory of Open Access Journals (Sweden)

    Delvio Venanzi

    2017-12-01

    Full Text Available Lean Six Sigma é uma gestão focada na qualidade e desempenho produtivo em sistemas operacionais. Este artigo discute os fundamentos desta metodologia através de duas diferentes concepções de gestão, Lean Manufacturing e Six Sigma. Primeiro, o artigo explica o DMAIC (definir, medir, analisar, melhorar e controlar e suas respectivas fases, após a filosofia Lean com o sipoc e técnicas de mapeamento de fluxo de valor. O artigo pretende mostrar a integração destes dois conceitos e seus resultados. A metodologia consistiu em uma teoria baseada em uma pesquisa bibliográfica de pesquisa exploratória que consistiu de três estudos de caso em empresas de diferenças localizadas em Sorocaba, São Paulo. Neste artigo estuda a aplicação de Lean Seis Sigma e seus resultados.

  19. Lattice sigma models with exact supersymmetry

    International Nuclear Information System (INIS)

    Simon Catterall; Sofiane Ghadab

    2004-01-01

    We show how to construct lattice sigma models in one, two and four dimensions which exhibit an exact fermionic symmetry. These models are discretized and twisted versions of conventional supersymmetric sigma models with N=2 supersymmetry. The fermionic symmetry corresponds to a scalar BRST charge built from the original supercharges. The lattice theories possess local actions and exhibit no fermion doubling. In the two and four dimensional theories we show that these lattice theories are invariant under additional discrete symmetries. We argue that the presence of these exact symmetries ensures that no fine tuning is required to achieve N=2 supersymmetry in the continuum limit. As a concrete example we show preliminary numerical results from a simulation of the O(3) supersymmetric sigma model in two dimensions. (author)

  20. Six Sigma Driven Enterprise Model Transformation

    Directory of Open Access Journals (Sweden)

    Raymond Vella

    2009-10-01

    Full Text Available Enterprise architecture methods provide a structured system to understand enterprise activities. However, existing enterprise modelling methodologies take static views of the enterprise and do not naturally lead to a path of improvement during enterprise model transformation. This paper discusses the need for a methodology to facilitate changes for improvement in an enterprise. The six sigma methodology is proposed as the tool to facilitate progressive and continual Enterprise Model Transformation to allow businesses to adapt to meet increased customer expectation and global competition. An alignment of six sigma with phases of GERAM life cycle is described with inclusion of Critical-To-Satisfaction (CTS requirements. The synergies of combining the two methodologies are presented in an effort to provide a more culturally embedded framework for Enterprise Model Transformation that builds on the success of six sigma.

  1. Designing a fractal antenna of 2400 MHz

    International Nuclear Information System (INIS)

    Miranda Hamburger, Fabio

    2012-01-01

    The design of a fractal antenna with 2400 MHz of frequency has been studied. The fractal used is described by Waclaw Spierpi.ski. The initial figure, also known as seed, is divided using equilateral triangles with the aim of obtaining a perimeter similar to a meaningful portion of wave length. The use of λ to establish an ideal perimeter has reduced the radiation resistance. The adequate number of iterations needed to design the antenna is calculated based on λ. (author) [es

  2. Design of 325 MHz spoke cavity

    International Nuclear Information System (INIS)

    Sha Peng; Huang Hong; Dai Jianping; Zu Guoquan; Li Han

    2012-01-01

    Spoke cavity can be used in the low-energy section of the proton accelerator. It has many significant advantages: compact structure, high value of R/Q, etc. The ADS (Accelerator Driven System) project will adopt many spoke cavities with different β values. Therefore, IHEP has began the research of β=0.14, 325 MHz spoke cavity. In this pa per, the dimensions, RF performances and mechanical properties of it are studied. (authors)

  3. Design of 2.5 GHz broad bandwidth microwave bandpass filter at operating frequency of 10 GHz using HFSS

    Science.gov (United States)

    Jasim, S. E.; Jusoh, M. A.; Mahmud, S. N. S.; Zamani, A. H.

    2018-04-01

    Development of low losses, small size and broad bandwidth microwave bandpass filter operating at higher frequencies is an active area of research. This paper presents a new route used to design and simulate microwave bandpass filter using finite element modelling and realized broad bandwidth, low losses, small dimension microwave bandpass filter operating at 10 GHz frequency using return loss method. The filter circuit has been carried out using Computer Aid Design (CAD), Ansoft HFSS software and designed with four parallel couple line model and small dimension (10 × 10 mm2) using LaAlO3 substrate. The response of the microwave filter circuit showed high return loss -50 dB at operating frequency at 10.4 GHz and broad bandwidth of 2.5 GHz from 9.5 to 12 GHz. The results indicate the filter design and simulation using HFSS is reliable and have the opportunity to transfer from lab potential experiments to the industry.

  4. A Lean Six Sigma journey in radiology.

    Science.gov (United States)

    Bucci, Ronald V; Musitano, Anne

    2011-01-01

    The department of radiology at Akron Children's Hospital embarked on a Lean Six Sigma mission as part of a hospital wide initiative to show increased customer satisfaction, reduce employee dissatisfaction and frustration, and decrease costs. Three processes that were addressed were reducing the MRI scheduling back-log, reconciling discrepancies in billing radiology procedures, and implementing a daily management system. Keys to success is that managers provide opportunities to openly communicate between department sections to break down barriers. Executive leaders must be engaged in Lean Six Sigma for the company to be successful.

  5. Supersymmetric sigma models and the heterotic string

    International Nuclear Information System (INIS)

    Hull, C.M.; Witten, E.

    1989-01-01

    The authors define the (1 + 1)-dimensional supersymmetry algebra of type (p, q) to be that generated by p right-handed Majorana-Weyl supercharges and q left-handed ones. They construct the non-linear sigma models with supersymmetry of type (1, 0) and (2, 0) and discuss their geometry and their relevance to compactifications of the heterotic superstring. The sigma-model anomalies can be canceled by a mechanism closely related to that used by Green and Schwarz to cancel gravitational and Yang-Mills anomalies for the superstring

  6. 6 Sigma DFSS technique with easy practice

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-12-15

    This book describes 6 Sigma DFSS technique which is easy to use. These are the titles of the contents : new demand, the reason that DFSS needs, when is DFSS used?, DMAIC and DMADV and the bastion for achievement of 6 sigma, new trouble, chief, Chang's new store, plan on kalguksu development propel, customers are holding the key, CTQ refinement, process capability evaluation, setting goal, finding of conception of optimum design, finding of design element, the last gateway, and it's time for a DFSS!.

  7. Heat transfer enhancement using 2MHz ultrasound.

    Science.gov (United States)

    Bulliard-Sauret, Odin; Ferrouillat, Sebastien; Vignal, Laure; Memponteil, Alain; Gondrexon, Nicolas

    2017-11-01

    The present work focuses on possible heat transfer enhancement from a heating plate towards tap water in forced convection by means of 2MHz ultrasound. The thermal approach allows to observe the increase of local convective heat transfer coefficients in the presence of ultrasound and to deduce a correlation between ultrasound power and Nusselt number. Heat transfer coefficient under ultrasound remains constant while heat transfer coefficient under silent conditions increases with Reynolds number from 900 up to 5000. Therefore, heat transfer enhancement factor ranges from 25% up to 90% for the same energy conditions (supplied ultrasonic power=110W and supplied thermal power=450W). In the same time cavitational activity due to 2MHz ultrasound emission was characterized from mechanical and chemical viewpoints without significant results. At least, Particle Image Velocimetry (PIV) measurements have been performed in order to investigate hydrodynamic modifications due to the presence of 2MHz ultrasound. It was therefore possible to propose a better understanding of heat transfer enhancement mechanism with high frequency ultrasound. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. Interaction of sigma factor sigmaN with Escherichia coli RNA polymerase core enzyme.

    Science.gov (United States)

    Scott, D J; Ferguson, A L; Gallegos, M T; Pitt, M; Buck, M; Hoggett, J G

    2000-12-01

    The equilibrium binding and kinetics of assembly of the DNA-dependent RNA polymerase (RNAP) sigma(N)-holoenzyme has been investigated using biosynthetically labelled 7-azatryptophyl- (7AW)sigma(N). The spectroscopic properties of such 7AW proteins allows their absorbance and fluorescence to be monitored selectively, even in the presence of high concentrations of other tryptophan-containing proteins. The 7AWsigma(N) retained its biological activity in stimulating transcription from sigma(N)-specific promoters, and in in vitro gel electrophoresis assays of binding to core RNAP from Escherichia coli. Furthermore, five Trp-->Ala single mutants of sigma(N) were shown to support growth under conditions of nitrogen limitation, and showed comparable efficiency in activating the sigma(N)-dependent nifH promoter in vivo, indicating that none of the tryptophan residues were essential for activity. The equilibrium binding of 7AWsigma(N) to core RNAP was examined by analytical ultracentrifugation. In sedimentation equilibrium experiments, absorbance data at 315 nm (which reports selectively on the distribution of free and bound 7AWsigma(N)) established that a 1:1 complex was formed, with a dissociation constant lower than 2 microM. The kinetics of the interaction between 7AWsigma(N) and core RNAP was investigated using stopped-flow spectrofluorimetry. A biphasic decrease in fluorescence intensity was observed when samples were excited at 280 nm, whereas only the slower of the two phases was observed at 315 nm. The kinetic data were analysed in terms of a mechanism in which a fast bimolecular association of sigma(N) with core RNAP is followed by a relatively slow isomerization step. The consequences of these findings on the competition between sigma(N) and the major sigma factor, sigma(70), in Escherichia coli are discussed.

  9. A reconfigurable complex band-pass filter with improved passive compensation

    International Nuclear Information System (INIS)

    Fan Chaojie; Mo Tingting; Chen Dongpo; Zhou Jianjun

    2012-01-01

    This paper presents a 5th-order Chebyshev-I active RC complex filter for multi-mode multi-band global navigation satellite systems (GNSS) RF receivers. An improved passive compensation technique is used to cancel the excess phase lag of the integrators, thus ensuring the in-band flatness of the frequency response over various ambient conditions. The filter has a programmable gain from 0 to 42 dB with a 6 dB step, a tunable center frequency at either 6.4 MHz or 16 MHz, and a bandwidth from 2 to 20 MHz with less than 3% frequency uncertainty. Implemented in a 0.18 μm CMOS process, the whole filter consumes 7.8 mA from a 1.8 V supply voltage and occupies a die area of 0.4 mm 2 . (semiconductor integrated circuits)

  10. 47 CFR 90.355 - LMS operations below 512 MHz.

    Science.gov (United States)

    2010-10-01

    ... PRIVATE LAND MOBILE RADIO SERVICES Intelligent Transportation Systems Radio Service § 90.355 LMS... LMS station and the nearest co-channel base station of another licensee operating a voice system is 75... MHz, 150-170 MHz, and 450-512 MHz bands may use either base-mobile frequencies currently assigned the...

  11. Imaging the Cemento-Enamel Junction Using a 20-MHz Ultrasonic Transducer.

    Science.gov (United States)

    Nguyen, Kim-Cuong T; Le, Lawrence H; Kaipatur, Neelambar R; Major, Paul W

    2016-01-01

    The cemento-enamel junction (CEJ), which is the intersection between enamel and cementum, is an important landmark in the diagnosis of periodontal disease. Pulse-echo ultrasound was used to image the CEJs of six porcine lower central incisors with a single 20-MHz transducer. A notch was longitudinally created on the enamel as a stable marker, from which the CEJ was measured. Data were acquired along the tooth's axis at 0.4-mm intervals. Time-distance data were bandpass-filtered to enhance signal-to-noise ratio and record density was increased fourfold to 0.1-mm spacing by a frequency-distance interpolation scheme. Reflections from the CEJ were unambiguously identified along with those from enamel, dentin and cementum. The notch-CEJ distances measured by the ultrasound and micro-computed tomography methods correlated strongly (r = 0.996, p < 0.05) and were in good agreement with the 95% lines of agreement between -0.49 and 0.17 mm, as statistically determined by Bland-Altman analysis. The results indicate the potential of ultrasound to be a reliable and non-ionizing technique to image the CEJ. Copyright © 2016 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

  12. Maass waveforms arising from sigma and related indefinite theta functions

    OpenAIRE

    Zwegers, Sander

    2010-01-01

    In this paper we consider an example of a Maass waveform which was constructed by Cohen from a function $\\sigma$, studied by Andrews, Dyson and Hickerson, and it's companion $\\sigma^*$. We put this example in a more general framework.

  13. Some examples of instantons in sigma models

    International Nuclear Information System (INIS)

    Kogan, Ya.; Markushevich, D.; Morozov, A.; Ol'shanetskij, M.; Perelomov, A.; Roslyj, A.

    1988-01-01

    Holomorphic instantons of arbitrary generation in manifolds and their boson and fermion zero modes are determined within the scope of the sigma model. General formulae for their quantitative evaluation are presented. Zero modes of spherical and toroidal instantons are discussed in detail

  14. Extracytoplasmic function sigma factors in Pseudomonas syringae

    DEFF Research Database (Denmark)

    Kiil, Kristoffer; Oguiza, J.A.; Ussery, D.W.

    2005-01-01

    Genome analyses of the plant pathogens Pseudomonas syringae pv. tomato DC3000, pv. syringae B728a and pv. phaseolicola 1448A reveal fewer extracytoplasmic function (ECF) sigma factors than in related Pseudomonads with different lifestyles. We highlight the presence of a P. syringae-specific ECF...

  15. Lean Six Sigma: Stap voor stap

    NARCIS (Netherlands)

    Does, R.J.M.M.; de Koning, H.; de Mast, J.

    2008-01-01

    Lean Six Sigma is de culminatie van ontwikkelingen in kwaliteitsverbetering in de 20ste eeuw. Het combineert belangrijke principes en technieken in een goed gestructureerde en geïntegreerde benadering. Het belichaamt wetenschappelijke inzichten over onderzoeksmethodologie, management en economie. In

  16. Need of Six Sigma in Education

    Science.gov (United States)

    Mehrotra, Dheeraj

    2007-01-01

    The marching trend of the new economic order has generated a new capsule of SIX SIGMA as a unified approach to process excellence. The tests reveal that it has transformed some of the most successful companies in the world like Motorola, GE etc. It is activated as an approach to aiming at the target by changing the culture of a company, involving…

  17. Six Sigma and Introductory Statistics Education

    Science.gov (United States)

    Maleyeff, John; Kaminsky, Frank C.

    2002-01-01

    A conflict exists between the way statistics is practiced in contemporary business environments and the way statistics is taught in schools of management. While businesses are embracing programs, such as six sigma and TQM, that bring statistical methods to the forefront of management decision making, students do not graduate with the skills to…

  18. How Six Sigma Methodology Improved Doctors' Performance

    Science.gov (United States)

    Zafiropoulos, George

    2015-01-01

    Six Sigma methodology was used in a District General Hospital to assess the effect of the introduction of an educational programme to limit unnecessary admissions. The performance of the doctors involved in the programme was assessed. Ishikawa Fishbone and 5 S's were initially used and Pareto analysis of their findings was performed. The results…

  19. Implementing Lean Six Sigma in organizations

    NARCIS (Netherlands)

    Lameijer, B.A.

    2017-01-01

    This thesis focuses on operational excellence following the Lean Six Sigma (LSS) method. As the popularity of implementing LSS grows, questions about implementing LSS in organizations arise, and this is where we aim to contribute. We study key questions about implementing LSS in organizations at two

  20. Harmonicity in supermanifolds and sigma models

    International Nuclear Information System (INIS)

    Munoz-Masque, Jaime; Vallejo, Jose A.

    2009-01-01

    We show that given an odd metric G on a supermanifold (M, A) and its associated Laplacian Δ, it is possible to interpret harmonic superfunctions (i.e., those f is an element of A such that Δf = 0) as solutions to a variational problem describing a supersymmetric sigma model.

  1. Sigma factors and promoters in Corynebacterium glutamicum

    Czech Academy of Sciences Publication Activity Database

    Pátek, Miroslav; Nešvera, Jan

    2011-01-01

    Roč. 154, 2-3 (2011), s. 101-113 ISSN 0168-1656 R&D Projects: GA ČR GC204/09/J015 Institutional research plan: CEZ:AV0Z50200510 Keywords : Corynebacterium glutamicum * Sigma factors * Promoters Subject RIV: EE - Microbiology, Virology Impact factor: 3.045, year: 2011

  2. Improving Learning Outcome Using Six Sigma Methodology

    Science.gov (United States)

    Tetteh, Godson A.

    2015-01-01

    Purpose: The purpose of this research paper is to apply the Six Sigma methodology to identify the attributes of a lecturer that will help improve a student's prior knowledge of a discipline from an initial "x" per cent knowledge to a higher "y" per cent of knowledge. Design/methodology/approach: The data collection method…

  3. Remarks on non compact sigma models

    International Nuclear Information System (INIS)

    Brunini, S.A.; Gomes, M.; Silva, A.J. da.

    1988-01-01

    O(N,1) noncompact sigma models quantized in an indefinite metric space. In two dimensions, by a direct computation the existence of a positive metric subspace where the S matrix is unitary. Is proved the properties of the model as function of the temperature are investigated in various space time dimensions. (author) [pt

  4. The Scientific Underpinning of Lean Six Sigma

    NARCIS (Netherlands)

    Does, R.J.M.M.; de Mast, J.; de Koning, H.; Bisgaard, S.

    2007-01-01

    The twentieth century saw an incredible development of professional organizations. The impact of technological advances is obvious, but besides these, innovations in management structures and methods have resulted in the highly productive organizations of today. Lean Six Sigma is not revolutionary.

  5. Lean Six Sigma for Service and Healthcare

    NARCIS (Netherlands)

    de Mast, J.; Does, R.J.M.M.; de Koning, H.

    2006-01-01

    Lean Six Sigma is built on principles and methods that have proven themselves over the twentieth century. It has incorporated the most effective approaches and integrated them into a full programme. It offers a management structure for organizing continuous improvement of routine tasks, such as

  6. A prototypical Sigma-1 receptor antagonist protects against brain ischemia

    OpenAIRE

    Schetz, John A.; Perez, Evelyn; Liu, Ran; Chen, Shiuhwei; Lee, Ivan; Simpkins, James W.

    2007-01-01

    Previous studies indicate that the Sigma-1 ligand 4-phenyl-1-(4-phenylbutyl) piperidine (PPBP) protects the brain from ischemia. Less clear is whether protection is mediated by agonism or antagonism of the Sigma-1 receptor, and whether drugs already in use for other indications and that interact with the Sigma-1 receptor might also prevent oxidative damage due to conditions such as cerebral ischemic stroke. The antipsychotic drug haloperidol is an antagonist of Sigma-1 receptors and in this s...

  7. Metamaterial composite bandpass filter with an ultra-broadband rejection bandwidth of up to 240 terahertz

    DEFF Research Database (Denmark)

    Strikwerda, Andrew; Zalkovskij, Maksim; Lorenzen, Dennis Lund

    2014-01-01

    We present a metamaterial, consisting of a cross structure and a metal mesh filter, that forms a composite with greater functional bandwidth than any terahertz (THz) metamaterial to date. Metamaterials traditionally have a narrow usable bandwidth that is much smaller than common THz sources......, such as photoconductive antennas and difference frequency generation. The composite structure shown here expands the usable bandwidth to exceed that of current THz sources. To highlight the applicability of this combination, we demonstrate a series of bandpass filters with only a single pass band, with a central...... frequency (f) that is scalable from 0.86–8.51 THz, that highly extinguishes other frequencies up to >240 THz. The performance of these filters is demonstrated in experiment, using both air biased coherent detection and a Fourier transform infrared spectrometer (FTIR), as well as in simulation. We present...

  8. Solar-blind ultraviolet band-pass filter based on metal—dielectric multilayer structures

    International Nuclear Information System (INIS)

    Wang Tian-Jiao; Xu Wei-Zong; Lu Hai; Ren Fang-Fang; Chen Dun-Jun; Zhang Rong; Zheng You-Dou

    2014-01-01

    Solar-blind ultraviolet (UV) band-pass filter has significant value in many scientific, commercial, and military applications, in which the detection of weak UV signal against a strong background of solar radiation is required. In this work, a solar-blind filter is designed based on the concept of “transparent metal”. The filter consisting of Al/SiO 2 multilayers could exhibit a high transmission in the solar-blind wavelength region and a wide stopband extending from near-ultraviolet to infrared wavelength range. The central wavelength, bandwidth, Q factor, and rejection ratio of the passband are numerically studied as a function of individual layer thickness and multilayer period. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

  9. Design of a Narrow Bandwidth Bandpass Filter Using Compact Spiral Resonator with Chirality

    Directory of Open Access Journals (Sweden)

    Weiping Li

    2016-01-01

    Full Text Available In this article, a compact narrow-bandpass filter with high selectivity and improved rejection level is presented. For miniaturization, a pair of double negative (DNG cells consisting of quasi-planar chiral resonators are cascaded and electrically loaded to a microstrip transmission line; short ended stubs are introduced to expand upper rejection band. The structure is analyzed using equivalent circuit models and simulated based on EM simulation software. For validation, the proposed filter is fabricated and measured. The measured results are in good agreement with the simulated ones. By comparing to other filters in the references, it is shown that the proposed filter has the advantage of skirt selectivity and compact size, so it can be integrated more conveniently in modern wireless communication systems and microwave planar circuits.

  10. A planar and tunable bandpass filter on a ferrite substrate with integrated windings

    KAUST Repository

    Arabi, Eyad A.

    2015-05-01

    Tunable Filters that are based on ferrite materials are often biased by external magnets or coils which are large and bulky. In this work a completely planar, CPW-based bandpass filter is presented with integrated windings. Due to these windings the size of the filter is only 26mm × 34mm × 0.38mm which is orders of magnitude smaller than the traditional designs with external windings. The filter is realized by electroplating of Copper over seed layers of Titanium and Gold over a YIG substrate. The fabricated filter achieves a tunability of 3.4% without any external magnets or coils. A good insertion loss of 2.3 dBs and rejection greater than 50 dBs have been obtained. To the best of the authors knowledge, this design is the first ferrite-based design that is completely planar and self-biased.

  11. Compact Microstrip Triple-Mode Bandpass Filters Using Dual-Stub-Loaded Spiral Resonators

    Directory of Open Access Journals (Sweden)

    K. D. Xu

    2017-04-01

    Full Text Available Two new microstrip triple-mode resonators loaded with T-shaped open stubs using axially and centrally symmetric spiral structures, respectively, are presented. Spiraled for circuit size reduction, these two half-wavelength resonators can both generate three resonant modes over a wide frequency band by loading two T-stubs with different lengths. Due to the structural symmetry, they can be analyzed by odd- and even-mode method. To validate the design concept, two compact bandpass filters (BPFs using these two novel resonators with center frequencies of 1.76 GHz and 2.44 GHz for the GSM1800 and WLAN/Zigbee applications, respectively, have been designed, fabricated and tested. The center frequencies and bandwidths can be tunable through the analysis of resonant frequency responses, fractional bandwidths and external quality factor versus the resonator parameters. The final measured results have achieved good consistence with the simulations of these two BPFs.

  12. Compact Dual-Band Bandpass Filter Using Stubs Loaded Ring Resonator

    Science.gov (United States)

    Xu, Jin

    2016-01-01

    This paper presents a novel second-order dual-band bandpass filter (BPF) by using proposed stubs loaded ring resonator. The resonant behavior of proposed stubs loaded ring resonator is analyzed by even-/odd-mode method, which shows its multiple-mode resonant characteristic. Parameters sweep is done so as to give the design guidelines. As an example, a second-order dual-band BPF operating at 1.8/5.2 GHz for GSM and WLAN applications is designed, fabricated and measured. The fabricated filter has a very compact size of 0.05λg×0.15λg. Measured results also show that the proposed dual-band BPF has a better than 20 dB rejection upper stopband from 5.47 GHz to 12.56 GHz. Good agreement is shown between the simulated and measured results.

  13. Notes on basis band-pass circuits; Notes sur les circuits de base passe-bande

    Energy Technology Data Exchange (ETDEWEB)

    Ailloud, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1959-07-01

    Resistor load amplifier stages, basic band-pass RC networks, conventional single-tuned circuits, have the same transfer function. Common properties and differences because diverse magnitude of parameters with proposed problems are exposed. Next the case of several cascaded stages (or networks) is examined when there is no reaction ones to another. (author) [French] Les etages amplificateurs a resistances, les circuits passe-bande RC elementaires, le circuit resonnant classique possedent la meme fonction de transfert. On fait ressortir les proprietes communes et les differences de comportement dues aux ordres de grandeur qu'il est possible de donner aux parametres en fonction des problemes a resoudre. On examine ensuite le cas de plusieurs etages (ou de plusieurs circuits) en cascade lorsqu'ils ne reagissent pas les uns sur les autres. (auteur)

  14. The structure of the .sigma.-ideal of .sigma.-porous sets

    Czech Academy of Sciences Publication Activity Database

    Zelený, M.; Pelant, Jan

    2004-01-01

    Roč. 45, č. 1 (2004), s. 37-72 ISSN 0010-2628 R&D Projects: GA ČR GA201/97/1161; GA ČR GA201/97/0216; GA ČR GA201/00/1466; GA AV ČR KSK1019101 Institutional research plan: CEZ:AV0Z1019905 Keywords : .sigma. proposity * descriptive set theory * .sigma.-ideal Subject RIV: BA - General Mathematics

  15. Incorporating Six Sigma Methodology Training into Chemical Engineering Education

    Science.gov (United States)

    Dai, Lenore L.

    2007-01-01

    Six Sigma is a buzz term in today's technology and business world and there has been increasing interest to initiate Six Sigma training in college education. We have successfully incorporated Six Sigma methodology training into a traditional chemical engineering course, Engineering Experimentation, at Texas Tech University. The students have…

  16. Operational excellence (six sigma) philosophy: Application to software quality assurance

    Energy Technology Data Exchange (ETDEWEB)

    Lackner, M.

    1997-11-01

    This report contains viewgraphs on operational excellence philosophy of six sigma applied to software quality assurance. This report outlines the following: goal of six sigma; six sigma tools; manufacturing vs administrative processes; Software quality assurance document inspections; map software quality assurance requirements document; failure mode effects analysis for requirements document; measuring the right response variables; and questions.

  17. Commutative $C^*$-algebras and $\\sigma$-normal morphisms

    OpenAIRE

    de Jeu, Marcel

    2003-01-01

    We prove in an elementary fashion that the image of a commutative monotone $\\sigma$-complete $C^*$-algebra under a $\\sigma$-normal morphism is again monotone $\\sigma$-complete and give an application of this result in spectral theory.

  18. 47 CFR 15.242 - Operation in the bands 174-216 MHz and 470-668 MHz.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Operation in the bands 174-216 MHz and 470-668... bands 174-216 MHz and 470-668 MHz. (a) The marketing and operation of intentional radiators under the... services, facilities, and beds for use beyond 24 hours in rendering medical treatment and institutions and...

  19. A 3-D miniaturized high selectivity bandpass filter in LTCC technology

    KAUST Repository

    Arabi, Eyad A.; Lahti, Markku S.; Vä hä -Heikkilä , Tauno; Shamim, Atif

    2014-01-01

    the out-of-band rejection by introducing a third transmission zero. The filter, designed for GPS band (1.57 GHz), has one of the smallest reported foot prints ((0.063×0.048×0.005)λg) and demonstrates the highest roll off factor (16.7 dB/100 MHz

  20. Fourier transform profilometry (FTP) using an innovative band-pass filter for accurate 3-D surface reconstruction

    Science.gov (United States)

    Chen, Liang-Chia; Ho, Hsuan-Wei; Nguyen, Xuan-Loc

    2010-02-01

    This article presents a novel band-pass filter for Fourier transform profilometry (FTP) for accurate 3-D surface reconstruction. FTP can be employed to obtain 3-D surface profiles by one-shot images to achieve high-speed measurement. However, its measurement accuracy has been significantly influenced by the spectrum filtering process required to extract the phase information representing various surface heights. Using the commonly applied 2-D Hanning filter, the measurement errors could be up to 5-10% of the overall measuring height and it is unacceptable to various industrial application. To resolve this issue, the article proposes an elliptical band-pass filter for extracting the spectral region possessing essential phase information for reconstructing accurate 3-D surface profiles. The elliptical band-pass filter was developed and optimized to reconstruct 3-D surface models with improved measurement accuracy. Some experimental results verify that the accuracy can be effectively enhanced by using the elliptical filter. The accuracy improvement of 44.1% and 30.4% can be achieved in 3-D and sphericity measurement, respectively, when the elliptical filter replaces the traditional filter as the band-pass filtering method. Employing the developed method, the maximum measured error can be kept within 3.3% of the overall measuring range.

  1. Frequency Arrangement For 700 MHz Band

    Directory of Open Access Journals (Sweden)

    Ancans G.

    2015-02-01

    Full Text Available The 694-790 MHz (700 MHz band was allocated by the 2012 World Radiocommunication Conference (WRC-12 in ITU Region 1 (Europe included, to the mobile service on a co-primary basis with other services to which this band was allocated on the primary basis and identified for the International Mobile Telecommunications (IMT. At the same time, the countries of Region 1 will be able also to continue using these frequencies for their broadcasting services if necessary. This allocation will be effective immediately after 2015 World Radiocommunication Conference (WRC-15. In order to make the best possible use of this frequency band for mobile service, a worldwide harmonized frequency arrangement is to be prepared to allow for large economies of scale and international roaming as well as utilizing the available spectrum in the best possible way, minimizing possible interference between services, facilitating deployment and cross-border coordination. The authors analyze different possible frequency arrangements and conclude on the frequency arrangement most suitable for Europe.

  2. Band-pass filtering algorithms for adaptive control of compressor pre-stall modes in aircraft gas-turbine engine

    Science.gov (United States)

    Kuznetsova, T. A.

    2018-05-01

    The methods for increasing gas-turbine aircraft engines' (GTE) adaptive properties to interference based on empowerment of automatic control systems (ACS) are analyzed. The flow pulsation in suction and a discharge line of the compressor, which may cause the stall, are considered as the interference. The algorithmic solution to the problem of GTE pre-stall modes’ control adapted to stability boundary is proposed. The aim of the study is to develop the band-pass filtering algorithms to provide the detection functions of the compressor pre-stall modes for ACS GTE. The characteristic feature of pre-stall effect is the increase of pressure pulsation amplitude over the impeller at the multiples of the rotor’ frequencies. The used method is based on a band-pass filter combining low-pass and high-pass digital filters. The impulse response of the high-pass filter is determined through a known low-pass filter impulse response by spectral inversion. The resulting transfer function of the second order band-pass filter (BPF) corresponds to a stable system. The two circuit implementations of BPF are synthesized. Designed band-pass filtering algorithms were tested in MATLAB environment. Comparative analysis of amplitude-frequency response of proposed implementation allows choosing the BPF scheme providing the best quality of filtration. The BPF reaction to the periodic sinusoidal signal, simulating the experimentally obtained pressure pulsation function in the pre-stall mode, was considered. The results of model experiment demonstrated the effectiveness of applying band-pass filtering algorithms as part of ACS to identify the pre-stall mode of the compressor for detection of pressure fluctuations’ peaks, characterizing the compressor’s approach to the stability boundary.

  3. The 938 MHz resonant damping loops for the 200 MHz SPS travelling wave cavities

    CERN Document Server

    Caspers, F

    2012-01-01

    Measurements of the beam stability in the SPS in 1982 - 1983 have shown a transversal instability for high intensity beams [1]. The fact that this related technical note is published nearly 30 years later, is related to the revival of interest in the frame of SPS impedance evaluation for LS1. Until now there was just a barely known paper folder available which could be consulted on request. The instability mentioned above was identified from beam measurements as raised by a deflecting mode at approximately 940 MHz in the 200 MHz travelling wave cavities of the SPS. Estimates showed that an attenuation of this particular mode by 20 dB would be desirable. In order to achieve this attenuation some vacuum ports on top of the cavities were available. For the damping devices three requirements had to be met: - sufficient damping at about 940 MHz - no serious change of cavity input VSWR at 200 MHz - no water cooling requirement for this higher order mode coupler.

  4. Six sigma and lean production adoption in a manufacturing company

    Directory of Open Access Journals (Sweden)

    Alisson Christian Scheller

    2014-11-01

    Full Text Available The connection among Lean Production with Six Sigma originated the Lean Six Sigma methodology, focused on processes variation and waste reduction. This methodology was developed on different ways in the companies and there is no consensus over its structure and its implementation. In this context, this paper aims to identify and analyze the main characteristics on the adoption and integration of Lean Six Sigma methodology through a case study conducted in a manufacturing company that adopts lean production and six sigma. The results show two important aspects of the Lean Six Sigma methodology. One of them is the adoption of the value stream mapping as a central tool on Lean Six Sigma. The other is the use of DMAIC for improvements actions. The study indicates that despite the difficulties on Lean Six Sigma implementation, the methodology offers benefits to the company that adopts it in the suitable way.

  5. 47 CFR 101.69 - Transition of the 1850-1990 MHz, 2110-2150 MHz, and 2160-2200 MHz bands from the fixed microwave...

    Science.gov (United States)

    2010-10-01

    ..., and 2160-2200 MHz bands from the fixed microwave services to personal communications services and...) SAFETY AND SPECIAL RADIO SERVICES FIXED MICROWAVE SERVICES Applications and Licenses License Transfers... MHz bands from the fixed microwave services to personal communications services and emerging...

  6. Enterprise Engineering Method supporting Six Sigma Approach

    OpenAIRE

    Jochem, Roland

    2007-01-01

    Enterprise Modeling (EM) is currently in operation either as a technique to represent and understand the structure and behavior of the enterprise, or as a technique to analyze business processes, and in many cases as support technique for business process reengineering. However, EM architectures and methodes for Enterprise Engineering can also used to support new management techniques like SIX SIGMA, because these new techniques need a clear, transparent and integrated definition and descript...

  7. Generalized Mathai-Quillen Topological Sigma Models

    OpenAIRE

    Llatas, Pablo M.

    1995-01-01

    A simple field theoretical approach to Mathai-Quillen topological field theories of maps $X: M_I \\to M_T$ from an internal space to a target space is presented. As an example of applications of our formalism we compute by applying our formulas the action and Q-variations of the fields of two well known topological systems: Topological Quantum Mechanics and type-A topological Sigma Model.

  8. TQM and six sigma in accounting literature

    OpenAIRE

    Vieira, João Manuel Franco Coelho Gouveia

    2014-01-01

    This study is based on the investigation of the relation between management accounting, Total Quality Management and six sigma, in articles published in 5 of the most renowned accounting journals: Management Accounting Review; European Accounting Review; Accounting, Auditing and Accountability; Critical Perspectives on Accounting; and Accounting Organizations and Society. Despite the vast existent literature related to both management accounting and quality management, this investigation c...

  9. BNL 703 MHz SRF cryomodule demonstration

    International Nuclear Information System (INIS)

    Burrill, A.; Ben-Zvi, I.; Calaga, R.; Dalesio, L.; Dottavio, T.; Gassner, D.; Hahn, H.; Hoff, L.; Kayran, D.; Kewisch, J.; Lambiase, R.; Lederle, D.; Litvinenko, V.; Mahler, G.; McIntyre, G.

    2009-01-01

    This paper will present the preliminary results of the testing of the 703 MHz SRF cryomodule designed for use in the ampere class ERL under construction at Brookhaven National Laboratory. The preliminary cavity tests, carried out at Thomas Jefferson Laboratory, demonstrated cavity performance of 20 MV/m with a Qo of 1 x 10 10 , results we expect to reproduce in the horizontal configuration. This test of the entire string assembly will allow us to evaluate all of the additional cryomodule components not previously tested in the VTA and will prepare us for our next milestone test which will be delivery of electrons from our injector through the cryomodule to the beam dump. This will also be the first demonstration of an accelerating cavity designed for use in an ampere class ERL, a key development which holds great promise for future machines

  10. The all-sky 408 MHz survey

    International Nuclear Information System (INIS)

    Haslam, C.G.T.; Salter, C.J.; Stoffel, H.

    1981-01-01

    A brief outline of the results of this survey is presented. The 408 MHz All-sky Survey has been made from four radio continuum surveys observed between 1965 and 1978, using the Jodrell Bank MKI telescope (Haslam et al., 1970), the Effelsberg 100 metre telescope (Haslam et al., 1974) and the Parkes 64 metre telescope (Haslam et al., 1975). A detailed description of the survey data reduction and calibration methods, with preliminary astronomical results will soon be published (Haslam et al., 1980a) and a second paper will give an atlas of maps at the full survey resolution of 51' arc between half power points (Haslam et al., 1980b). A map, smoothed to a gaussian beam with resolution between half power poitns of 3 0 , is presented. (Auth.)

  11. A 16-bit sigma-delta modulator applied in micro-machined inertial sensors

    Science.gov (United States)

    Honglin, Xu; Qiang, Fu; Hongna, Liu; Liang, Yin; Pengfei, Wang; Xiaowei, Liu

    2014-04-01

    A fourth-order low-distortion low-pass sigma-delta (ΣΔ) modulator is presented for micro-machined inertial sensors. The proposed single-loop single-bit feedback modulator is optimized with a feed-forward path to decrease the nonlinearities and power consumption. The IC is implemented in a standard 0.6 μm CMOS technology and operates at a sampling frequency of 3.846 MHz. The chip area is 2.12 mm2 with 23 pads. The experimental results indicate a signal-to-noise ratio (SNR) of 100 dB and dynamic range (DR) of 103 dB at an oversampling rate (OSR) of 128 with the input signal amplitude of -3.88 dBFS at 9.8 kHz; the power consumption is 15 mW at a 5 V supply.

  12. Cost-effective bidirectional digitized radio-over-fiber systems employing sigma delta modulation

    Science.gov (United States)

    Lee, Kyung Woon; Jung, HyunDo; Park, Jung Ho

    2016-11-01

    We propose a cost effective digitized radio-over-fiber (D-RoF) system employing a sigma delta modulation (SDM) and a bidirectional transmission technique using phase modulated downlink and intensity modulated uplink. SDM is transparent to different radio access technologies and modulation formats, and more suitable for a downlink of wireless system because a digital to analog converter (DAC) can be avoided at the base station (BS). Also, Central station and BS share the same light source by using a phase modulation for the downlink and an intensity modulation for the uplink transmission. Avoiding DACs and light sources have advantages in terms of cost reduction, power consumption, and compatibility with conventional wireless network structure. We have designed a cost effective bidirectional D-RoF system using a low pass SDM and measured the downlink and uplink transmission performance in terms of error vector magnitude, signal spectra, and constellations, which are based on the 10MHz LTE 64-QAM standard.

  13. 470‐MHz–698‐MHz IEEE 802.15.4m Compliant RF CMOS Transceiver

    Directory of Open Access Journals (Sweden)

    Youngho Seo

    2018-04-01

    Full Text Available This paper proposes an IEEE 802.15.4m compliant TV white‐space orthogonal frequency‐division multiplexing (TVWS‐(OFDM radio frequency (RF transceiver that can be adopted in advanced metering infrastructures, universal remote controllers, smart factories, consumer electronics, and other areas. The proposed TVWS‐OFDM RF transceiver consists of a receiver, a transmitter, a 25% duty‐cycle local oscillator generator, and a delta‐sigma fractional‐N phase‐locked loop. In the TV band from 470 MHz to 698 MHz, the highly linear RF transmitter protects the occupied TV signals, and the high‐Q filtering RF receiver is tolerable to in‐band interferers as strong as −20 dBm at a 3‐MHz offset. The proposed TVWS‐OFDM RF transceiver is fabricated using a 0.13‐μm CMOS process, and consumes 47 mA in the Tx mode and 35 mA in the Rx mode. The fabricated chip shows a Tx average power of 0 dBm with an error‐vector‐magnitude of  3%, and a sensitivity level of −103 dBm with a packet‐error‐rate of 3%. Using the implemented TVWS‐OFDM modules, a public demonstration of electricity metering was successfully carried out.

  14. Polarization-selective infrared bandpass filter based on a two-layer subwavelength metallic grating

    Science.gov (United States)

    Hohne, Andrew J.; Moon, Benjamin; Baumbauer, Carol L.; Gray, Tristan; Dilts, James; Shaw, Joseph A.; Dickensheets, David L.; Nakagawa, Wataru

    2017-08-01

    We present the design, fabrication, and characterization of a polarization-selective infrared bandpass filter based on a two-layer subwavelength metallic grating for use in polarimetric imaging. Gold nanowires were deposited via physical vapor deposition (PVD) onto a silicon surface relief grating that was patterned using electron beam lithography (EBL) and fabricated using standard silicon processing techniques. Optical characterization with a broad-spectrum tungsten halogen light source and a grating spectrometer showed normalized peak TM transmission of 53% with a full-width at half-maximum (FWHM) of 122 nm, which was consistent with rigorous coupled-wave analysis (RCWA) simulations. Simulation results suggested that device operation relied on suppression of the TM transmission caused by surface plasmon polariton (SPP) excitation at the gold-silicon interface and an increase in TM transmission caused by a Fabry-Perot (FP) resonance in the cavity between the gratings. TE rejection occurred at the initial air/gold interface. We also present simulation results of an improved design based on a two-dielectric grating where two different SPP resonances allowed us to improve the shape of the passband by suppressing the side lobes. This newer design resulted in improved side-band performance and increased peak TM transmission.

  15. Mode Coupling and Nonlinear Resonances of MEMS Arch Resonators for Bandpass Filters

    KAUST Repository

    Hajjaj, Amal Z.

    2017-01-30

    We experimentally demonstrate an exploitation of the nonlinear softening, hardening, and veering phenomena (near crossing), where the frequencies of two vibration modes get close to each other, to realize a bandpass filter of sharp roll off from the passband to the stopband. The concept is demonstrated based on an electrothermally tuned and electrostatically driven MEMS arch resonator operated in air. The in-plane resonator is fabricated from a silicon-on-insulator wafer with a deliberate curvature to form an arch shape. A DC current is applied through the resonator to induce heat and modulate its stiffness, and hence its resonance frequencies. We show that the first resonance frequency increases up to twice of the initial value while the third resonance frequency decreases until getting very close to the first resonance frequency. This leads to the phenomenon of veering, where both modes get coupled and exchange energy. We demonstrate that by driving both modes nonlinearly and electrostatically near the veering regime, such that the first and third modes exhibit softening and hardening behavior, respectively, sharp roll off from the passband to the stopband is achievable. We show a flat, wide, and tunable bandwidth and center frequency by controlling the electrothermal actuation voltage.

  16. Photonic bandpass filter characteristics of multimode SOI waveguides integrated with submicron gratings.

    Science.gov (United States)

    Sah, Parimal; Das, Bijoy Krishna

    2018-03-20

    It has been shown that a fundamental mode adiabatically launched into a multimode SOI waveguide with submicron grating offers well-defined flat-top bandpass filter characteristics in transmission. The transmitted spectral bandwidth is controlled by adjusting both waveguide and grating design parameters. The bandwidth is further narrowed down by cascading two gratings with detuned parameters. A semi-analytical model is used to analyze the filter characteristics (1500  nm≤λ≤1650  nm) of the device operating in transverse-electric polarization. The proposed devices were fabricated with an optimized set of design parameters in a SOI substrate with a device layer thickness of 250 nm. The pass bandwidth of waveguide devices integrated with single-stage gratings are measured to be ∼24  nm, whereas the device with two cascaded gratings with slightly detuned periods (ΔΛ=2  nm) exhibits a pass bandwidth down to ∼10  nm.

  17. Design of a Balun Bandpass Filter with Asymmetrical Coupled Microstrip Lines

    Science.gov (United States)

    Wang, Xuedao; Wang, Jianpeng; Zhang, Gang; Huang, Feng

    2017-07-01

    A new microstrip coupled-line balun topology and its application to the balun bandpass filter (BPF) with a triple mode response are proposed in this paper. The involved balun structure is composed of two back-to-back quarter-wavelength (λ/4) asymmetrical coupled-line sections. Detailed design formulas based on the asymmetrical coupled-line theory are given to validate the feasibility of the balun. Besides, to obtain filtering performance simultaneously, the balun is then effectively integrated with a pair of triple mode resonators. To demonstrate the design concept of the balun BPF, a prototype operating at 2.4 GHz with the fractional bandwidth (FBW) of about 19.2 % is designed, fabricated, and measured. Results indicate that between the two balanced outputs, the amplitude imbalance is less than 0.3 dB and the phase difference is within 180°±5° inside the whole passband. Both simulated and experimental results are in good agreement.

  18. Glomerular barrier behaves as an atomically precise bandpass filter in a sub-nanometre regime

    Science.gov (United States)

    Du, Bujie; Jiang, Xingya; Das, Anindita; Zhou, Qinhan; Yu, Mengxiao; Jin, Rongchao; Zheng, Jie

    2017-11-01

    The glomerular filtration barrier is known as a 'size cutoff' slit, which retains nanoparticles or proteins larger than 6-8 nm in the body and rapidly excretes smaller ones through the kidneys. However, in the sub-nanometre size regime, we have found that this barrier behaves as an atomically precise 'bandpass' filter to significantly slow down renal clearance of few-atom gold nanoclusters (AuNCs) with the same surface ligands but different sizes (Au18, Au15 and Au10-11). Compared to Au25 (∼1.0 nm), just few-atom decreases in size result in four- to ninefold reductions in renal clearance efficiency in the early elimination stage, because the smaller AuNCs are more readily trapped by the glomerular glycocalyx than larger ones. This unique in vivo nano-bio interaction in the sub-nanometre regime also slows down the extravasation of sub-nanometre AuNCs from normal blood vessels and enhances their passive targeting to cancerous tissues through an enhanced permeability and retention effect. This discovery highlights the size precision in the body's response to nanoparticles and opens a new pathway to develop nanomedicines for many diseases associated with glycocalyx dysfunction.

  19. Realisation and optical engineering of linear variable bandpass filters in nanoporous anodic alumina photonic crystals.

    Science.gov (United States)

    Sukarno; Law, Cheryl Suwen; Santos, Abel

    2017-06-08

    We present the first realisation of linear variable bandpass filters in nanoporous anodic alumina (NAA-LVBPFs) photonic crystal structures. NAA gradient-index filters (NAA-GIFs) are produced by sinusoidal pulse anodisation and used as photonic crystal platforms to generate NAA-LVBPFs. The anodisation period of NAA-GIFs is modified from 650 to 850 s to systematically tune the characteristic photonic stopband of these photonic crystals across the UV-visible-NIR spectrum. Then, the nanoporous structure of NAA-GIFs is gradually widened along the surface under controlled conditions by wet chemical etching using a dip coating approach aiming to create NAA-LVBPFs with finely engineered optical properties. We demonstrate that the characteristic photonic stopband and the iridescent interferometric colour displayed by these photonic crystals can be tuned with precision across the surface of NAA-LVBPFs by adjusting the fabrication and etching conditions. Here, we envisage for the first time the combination of the anodisation period and etching conditions as a cost-competitive, facile, and versatile nanofabrication approach that enables the generation of a broad range of unique LVBPFs covering the spectral regions. These photonic crystal structures open new opportunities for multiple applications, including adaptive optics, hyperspectral imaging, fluorescence diagnostics, spectroscopy, and sensing.

  20. W-band waveguide bandpass filter with E-plane cut

    DEFF Research Database (Denmark)

    Furtula, Vedran; Salewski, Mirko

    2014-01-01

    In this paper, we present a design and measurements of a five-section bandpass filter with a passband from 96 to 106 GHz. The insertion loss is less than 1.4 dB in the passband, and the rejection is better than 40 dB in the range from 115 to 142 GHz. We use transmission line coupling theory based...... on Tchebyscheff’s synthesis in order to provide an initial guess for the geometrical parameters of the filter such as cavity lengths and coupling widths. The filter is manufactured from brass in two halves in the E-plane cut topology. The S-parameters of the filter are measured and compared with the simulations....... The measured passband insertion loss is approximately 0.4 dB worse than in the simulation, and the measured passband width is approximately 3.4% narrower. The measured filter attenuation roll-off corresponds well to the simulation. We also compare our S-parameter measurements of the E-plane filter...

  1. Piecewise spectrally band-pass for compressive coded aperture spectral imaging

    International Nuclear Information System (INIS)

    Qian Lu-Lu; Lü Qun-Bo; Huang Min; Xiang Li-Bin

    2015-01-01

    Coded aperture snapshot spectral imaging (CASSI) has been discussed in recent years. It has the remarkable advantages of high optical throughput, snapshot imaging, etc. The entire spatial-spectral data-cube can be reconstructed with just a single two-dimensional (2D) compressive sensing measurement. On the other hand, for less spectrally sparse scenes, the insufficiency of sparse sampling and aliasing in spatial-spectral images reduce the accuracy of reconstructed three-dimensional (3D) spectral cube. To solve this problem, this paper extends the improved CASSI. A band-pass filter array is mounted on the coded mask, and then the first image plane is divided into some continuous spectral sub-band areas. The entire 3D spectral cube could be captured by the relative movement between the object and the instrument. The principle analysis and imaging simulation are presented. Compared with peak signal-to-noise ratio (PSNR) and the information entropy of the reconstructed images at different numbers of spectral sub-band areas, the reconstructed 3D spectral cube reveals an observable improvement in the reconstruction fidelity, with an increase in the number of the sub-bands and a simultaneous decrease in the number of spectral channels of each sub-band. (paper)

  2. Compact HTS bandpass filter employing CPW quarter-wavelength resonators with strongly-coupled open stubs

    Energy Technology Data Exchange (ETDEWEB)

    Satoh, K; Koizumi, D; Narahashi, S [Research Laboratories, NTT DoCoMo, Inc., 3-5 Hikari-no-oka, Yokosuka, Kanagwa, 239-8536 (Japan)], E-mail: satokei@nttdocomo.co.jp

    2008-02-01

    This paper presents a novel compact high temperature superconducting (HTS) bandpass filter (BPF) that employs a newly developed miniaturized coplanar-waveguide (CPW) quarter-wavelength resonators with strongly-coupled open stubs. The proposed resonator has a structure in which the open stubs are aligned close to the center conductor of the resonator. This is because strongly-coupled resonators have widely-split resonant frequencies, and the lowest resonant frequency is employed as the fundamental resonant frequency of the resonator in order to achieve miniaturization. The proposed resonator is 1.7 mm or less in length for use in the 5-GHz band, whereas the conventional straight resonator is approximately 6.4 mm long. A four-pole Chebyshev HTS BPF is designed and fabricated using the proposed CPW resonators. The entire length of the proposed four-pole filter is 15 mm. The frequency response of the fabricated filter agrees well with the electromagnetic simulation results. The proposed filter achieves a size reduction of at least 50% compared to previously reported filters without any degradation in the frequency characteristics.

  3. Study of the characteristics of forced homogeneous turbulence using band-pass Fourier filtering

    Energy Technology Data Exchange (ETDEWEB)

    Kareem, Waleed Abdel [Suez Canal University, Suez (Egypt)

    2012-03-15

    Simulations of forced homogeneous isotropic turbulence with resolutions of 128{sup 3} and 256{sup 3} using the Lattice Boltzmann method are carried out. The multi-scale vortical structures are identified using the band-pass Fourier cutoff filtering. Three fields at each simulation are extracted and their characteristics are studied. The vortical structures are visualized using the Q-identification method. A new lattice segmentation scheme to identify the central axes of the vortical structures is introduced. The central points of each vortex are identified and they are connected using the direction cosines technique. Results show that the Q-spectrum of the fine scale field survives at low and high wave-numbers. However, the large and intermediate Q-spectra survives till wave-numbers less than or equal to twice the used velocity cutoff wave-numbers. It is found that the extracted central axes clearly resemble the corresponding vortical structures at each scale. Using the central axes scheme, the radii and lengths of the vortical structures at each scale are determined and compared. It is also found that the radii of the identified vortical structures at each scale in both simulations are of the order of several times the Kolmogorov microscales.

  4. An improved ultra-wideband bandpass filter design using split ring resonator with coupled microstrip line

    Science.gov (United States)

    Umeshkumar, Dubey Suhmita; Kumar, Manish

    2018-04-01

    This paper incorporates an improved design of Ultra Wideband Bandpass filter by using split ring resonators (SRR) along with the coupled microstrip lines. The use of split ring resonators and shunt step impedance open circuit stub enhances the stability due to transmission zeroes at the ends. The designing of filter and simulation of parameters is carried out using Ansoft's HFSS 13.0 software on RT/Duroid 6002 as a substrate with dielectric constant of 2.94. The design utilizes a frequency band from 22GHz to 29GHz. This band is reserved for Automotive Radar system and sensors as per FCC specifications. The proposed design demonstrates insertion loss less than 0.6dB and return loss better than 12dB at mid frequency i.e. 24.4GHz. The reflection coefficient shows high stability of about 12.47dB at mid frequency. The fractional bandwidth of the proposed filter is about 28.7% and size of filter design is small due to thickness of 0.127mm.

  5. Application of Cu{sub 2}O-doped phosphate glasses for bandpass filter

    Energy Technology Data Exchange (ETDEWEB)

    Elhaes, H. [Physics Department, Faculty of Women for Arts, Science and Education, Ain Shams University, 11757 Cairo (Egypt); Attallah, M., E-mail: m_atallah94@yahoo.com [Basic Science Department, Higher Technological Institute, 10th of Ramadan City (Egypt); Elbashar, Y.; El-Okr, M. [Physics Department, Faculty of Science, Al Azhar University, Cairo (Egypt); Ibrahim, M. [Spectroscopy Department, National Research Centre, 12311 Dokki, Cairo (Egypt)

    2014-09-15

    Phosphate glasses doped with copper ions having general composition 42P{sub 2}O{sub 5}–39ZnO–(18−x) Na{sub 2}O–1CaO–xCu{sub 2}O [x=2, 4, 6, 8, 10 mol%] were prepared using a conventional melt-quench technique. Physical and chemical properties of the glasses were investigated using X-ray diffraction technique and UV–visible optical absorption. The density was measured by Archimedes' method, and molar volume (V{sub M}) was calculated. It is found that density and molar volume show opposite trend by increasing Cu{sub 2}O content. Absorbance and transmittance at the normal incidence are measured by a spectrophotometer in the spectral range of 190–1100 nm. Analyses of the obtained results were considered in the frame of current theories. Absorption data were used for absorption coefficient, the optical band gap (E{sub opt}), the cutoff in UV and IR bands to the bandpass filter, which confirmed the optical properties of this type of filter. E{sub opt} values for different glass samples are found to decrease with increasing Cu{sub 2}O content.

  6. STELLAR CORONAE, SOLAR FLARES: A DETAILED COMPARISON OF {sigma} GEM, HR 1099, AND THE SUN IN HIGH-RESOLUTION X-RAYS

    Energy Technology Data Exchange (ETDEWEB)

    Huenemoerder, David P. [Massachusetts Institute of Technology, Kavli Institute for Astrophysics and Space Research, 70 Vassar St., Cambridge, MA 02139 (United States); Phillips, Kenneth J. H. [Visiting Scientist, Space Research Center, Polish Academy of Sciences, 51-622, Kopernika 11, Wroclaw (Poland); Sylwester, Janusz; Sylwester, Barbara, E-mail: dph@space.mit.edu, E-mail: kennethjhphillips@yahoo.com, E-mail: js@cbk.pan.wroc.pl, E-mail: bs@cbk.pan.wroc.pl [Space Research Center, Polish Academy of Sciences, 51-622, Kopernika 11, Wroclaw (Poland)

    2013-05-10

    The Chandra High Energy Transmission Grating Spectrometer (HETG) spectra of the coronally active binary stars {sigma} Gem and HR 1099 are among the highest fluence observations for such systems taken at high spectral resolution in X-rays with this instrument. This allows us to compare their properties in detail to solar flare spectra obtained with the Russian CORONAS-F spacecraft's RESIK instrument at similar resolution in an overlapping bandpass. Here we emphasize the detailed comparisons of the 3.3-6.1 A region (including emission from highly ionized S, Si, Ar, and K) from solar flare spectra to the corresponding {sigma} Gem and HR 1099 spectra. We also model the larger wavelength range of the HETG, from 1.7 to 25 A - having emission lines from Fe, Ca, Ar, Si, Al, Mg, Ne, O, and N-to determine coronal temperatures and abundances. {sigma} Gem is a single-lined coronally active long-period binary which has a very hot corona. HR 1099 is a similar, but shorter period, double-lined system. With very deep HETG exposures we can even study emission from some of the weaker species, such as K, Na, and Al, which are important since they have the lowest first ionization potentials, a parameter well known to be correlated with elemental fractionation in the solar corona. The solar flare temperatures reach Almost-Equal-To 20 MK, comparable to the {sigma} Gem and HR 1099 coronae. During the Chandra exposures, {sigma} Gem was slowly decaying from a flare and its spectrum is well characterized by a collisional ionization equilibrium plasma with a broad temperature distribution ranging from 2 to 60 MK, peaking near 25 MK, but with substantial emission from 50 MK plasma. We have detected K XVIII and Na XI emission which allow us to set limits on their abundances. HR 1099 was also quite variable in X-rays, also in a flare state, but had no detectable K XVIII. These measurements provide new comparisons of solar and stellar coronal abundances, especially at the lowest first

  7. Spectrophotometry of peculiar B and A stars. XVIII - The helium rich variable stars HR 1890, Sigma Orionis E, and HD 37776

    Science.gov (United States)

    Adelman, S. J.; Pyper, D. M.

    1985-01-01

    Optical region spectrophotometry at 3300-7850 A has been obtained for three helium rich stars, HR 1890, Sigma Ori E, and HD 37776, of the Orion OB1 Association. New uvby-beta photometry of HR 1890 and HD 37776 as well as published data are also used to investigate the variability of these stars. A new period of 1.53862 days was determined for HD 37776. For all three stars H-beta varies in antiphase with strong He I lines. The spectrophotometric bandpass containing the strong He I line at 4471 A varies in phase with the R index of Pedersen and Thomsen (1977). Evidence is found for weak absorption features which appear to be an extension of the 5200 A feature seen in cooler CP stars.

  8. Miniaturized and Ferrite Based Tunable Bandpass Filters in LCP and LTCC Technologies for SoP Applications

    KAUST Repository

    Arabi, Eyad A.

    2015-04-01

    Wireless systems with emerging applications are leaning towards small size, light-weight and low cost. Another trend for these wireless devices is that new applications and functionalities are being added without increasing the size of the device. To accomplish this, individual components must be miniaturized and the system should be designed to maximize the integration of the individual components. The high level of 3D integration feasible in system on package design (SoP) concept can fulfill the latter requirement. Bandpass filters are important components on all wireless systems to reject the unwanted signals and reduce interference. Being mostly implemented with passive and distributed components, bandpass filters take considerable space in a wireless system. Moreover, with emerging bands and multiple applications encompassed in a single device, many bandpass filters are required. The miniaturization related to bandpass filters can be approached by three main ways: (1) at the component level through the miniaturization of individual bandpass filters, (2) at the system level through the use of tunable filters to reduce the overall number of filters, and (3) at the system level through the high level of integration in a 3D SoP platform. In this work we have focused on all three aspects of miniaturization of band pass filters mentioned above. In the first part of this work, a low frequency (1.5 GHz global positioning system (GPS) band) filter implemented through 3D lumped components in two leading SoP technologies, namely low temperature co-fired ceramic (LTCC) and the liquid crystal polymers (LCP) is demonstrated. The miniaturized filter is based on a second order topology, which has been modified to improve the selectivity and out-of-band rejection without increasing the size. Moreover, for the case of LCP, the filter is realized in an ultra-thin stack up comprising four metallization layers with an overall thickness of only 100 _m. Due to its ultra

  9. A Method against Interrupted-Sampling Repeater Jamming Based on Energy Function Detection and Band-Pass Filtering

    Directory of Open Access Journals (Sweden)

    Hui Yuan

    2017-01-01

    Full Text Available Interrupted-sampling repeater jamming (ISRJ is a new kind of coherent jamming to the large time-bandwidth linear frequency modulation (LFM signal. Many jamming modes, such as lifelike multiple false targets and dense false targets, can be made through setting up different parameters. According to the “storage-repeater-storage-repeater” characteristics of the ISRJ and the differences in the time-frequency-energy domain between the ISRJ signal and the target echo signal, one new method based on the energy function detection and band-pass filtering is proposed to suppress the ISRJ. The methods mainly consist of two parts: extracting the signal segments without ISRJ and constructing band-pass filtering function with low sidelobe. The simulation results show that the method is effective in the ISRJ with different parameters.

  10. Heterotic sigma models and non-linear strings

    International Nuclear Information System (INIS)

    Hull, C.M.

    1986-01-01

    The two-dimensional supersymmetric non-linear sigma models are examined with respect to the heterotic string. The paper was presented at the workshop on :Supersymmetry and its applications', Cambridge, United Kingdom, 1985. The non-linear sigma model with Wess-Zumino-type term, the coupling of the fermionic superfields to the sigma model, super-conformal invariance, and the supersymmetric string, are all discussed. (U.K.)

  11. Six Sigma Process and its Impact on the Organizational Productivity

    OpenAIRE

    Masoud Hekmatpanah; Mohammad Sadroddin; Saeid Shahbaz; Farhad Mokhtari; Farahnaz Fadavinia

    2008-01-01

    The six sigma method is a project-driven management approach to improve the organization-s products, services, and processes by continually reducing defects in the organization. Understanding the key features, obstacles, and shortcomings of the six sigma method allows organizations to better support their strategic directions, and increasing needs for coaching, mentoring, and training. It also provides opportunities to better implement six sigma projects. The purpose of this paper is the surv...

  12. The use of the Six Sigma concept in supply logistics

    Directory of Open Access Journals (Sweden)

    Agnieszka Szmelter

    2012-12-01

    Full Text Available This paper aims to present Six Sigma as one of the concepts of business process improvement, including logistics processes. Firstly, the author presents the role of information logistics and controlling to improve the efficiency of supply logistics. Then, she focuses on the characteristics of Six Sigma, including Lean Management philosophy, and identifies the connection between logistics and this methodology. She also presents an example of using the Six Sigma tools in the process of supply in a chosen company.

  13. Six Sigma, absorptive capacity and organizational learning orientation

    OpenAIRE

    Gutiérrez Gutiérrez , Leopoldo J; Bustinza Sánchez , Oscar F; Barrales Molina , Vanesa

    2011-01-01

    Abstract The importance of the Six Sigma methodology in industry is growing constantly. However, there are few empirical studies that analyze the advantages of this methodology and its positive effects on organizational performance. The purpose of this paper is to extend understanding of the success of Six Sigma quality management initiatives by investigating the effects of Six Sigma teamwork and process management on absorptive capacity. It also seeks to understand the relation be...

  14. Rib-pillar mining at Sigma Colliery

    Energy Technology Data Exchange (ETDEWEB)

    De Beer, J J.S.; Hunter, F; Neethling, A F [Sigma Colliery, Sasolburg (South Africa)

    1991-06-01

    The paper describes the rib-pillar extraction method now used at Sigma Colliery in the Orange Free State. In this method, access roadways (with a high safety factor) are developed into a block of coal suitable for total extraction; pillars that have a low safety factor are then formed and extracted immediately. The method, together with the current practices of labour management, has resulted in better utilization of the coal resources and capital, increased production and labour productivity, and improved safety. 11 figs.

  15. Euclidean supersymmetry, twisting and topological sigma models

    International Nuclear Information System (INIS)

    Hull, C.M.; Lindstroem, U.; Santos, L. Melo dos; Zabzine, M.; Unge, R. von

    2008-01-01

    We discuss two dimensional N-extended supersymmetry in Euclidean signature and its R-symmetry. For N = 2, the R-symmetry is SO(2) x SO(1, 1), so that only an A-twist is possible. To formulate a B-twist, or to construct Euclidean N = 2 models with H-flux so that the target geometry is generalised Kahler, it is necessary to work with a complexification of the sigma models. These issues are related to the obstructions to the existence of non-trivial twisted chiral superfields in Euclidean superspace.

  16. String Sigma Models on Curved Supermanifolds

    Directory of Open Access Journals (Sweden)

    Roberto Catenacci

    2018-04-01

    Full Text Available We use the techniques of integral forms to analyze the easiest example of two-dimensional sigma models on a supermanifold. We write the action as an integral of a top integral form over a D = 2 supermanifold, and we show how to interpolate between different superspace actions. Then, we consider curved supermanifolds, and we show that the definitions used for flat supermanifolds can also be used for curved supermanifolds. We prove it by first considering the case of a curved rigid supermanifold and then the case of a generic curved supermanifold described by a single superfield E.

  17. Topological sigma B model in 4-dimensions

    International Nuclear Information System (INIS)

    Jun, Hyun-Keun; Park, Jae-Suk

    2008-01-01

    We propose a 4-dimensional version of topological sigma B-model, governing maps from a smooth compact 4-manifold M to a Calabi-Yau target manifold X. The theory depends on complex structure of X, while is independent of Kaehler metric of X. The theory is also a 4-dimensional topological field theory in the sense that the theory is independent of variation of Riemannian metric of the source 4-manifold M, potentially leading to new smooth invariant of 4-manifolds. We argue that the theory also comes with a topological family parametrized by the extended moduli space of complex structures.

  18. Mucosal vaccination by adenoviruses displaying reovirus sigma 1

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, Eric A. [Department of Internal Medicine, Division of Infectious Diseases, Translational Immunovirology and Biodefense Program, Mayo Clinic, Rochester, MN 55902 (United States); Camacho, Zenaido T. [Department of Cell Biology, Department of Natural Sciences, Western New Mexico University, Silver City, NM 88062 (United States); Hillestad, Matthew L. [Nephrology Training Program, Mayo Clinic, Rochester, MN 55902 (United States); Crosby, Catherine M.; Turner, Mallory A.; Guenzel, Adam J.; Fadel, Hind J. [Virology and Gene Therapy Graduate Program, Mayo Clinic, Rochester, MN 55902 (United States); Mercier, George T. [Department of Physics, University of Houston, Houston, TX 77004 (United States); Barry, Michael A., E-mail: mab@mayo.edu [Department of Internal Medicine, Division of Infectious Diseases, Translational Immunovirology and Biodefense Program, Mayo Clinic, Rochester, MN 55902 (United States); Department of Immunology and Department of Molecular Medicine, Mayo Clinic, Rochester, MN 55902 (United States)

    2015-08-15

    We developed adenovirus serotype 5 (Ad5) vectors displaying the sigma 1 protein from reovirus as mucosal vaccines. Ad5-sigma retargets to JAM-1 and sialic acid, but has 40-fold reduced gene delivery when compared to Ad5. While weaker at transduction, Ad5-sigma generates stronger T cell responses than Ad5 when used for mucosal immunization. In this work, new Ad5-fiber-sigma vectors were generated by varying the number of fiber β-spiral shaft repeats (R) between the fiber tail and sigma. Increasing chimera length led to decreasing insertion of these proteinsAd5 virions. Ad-R3 and R14 vectors effectively targeted JAM-1 in vitro while R20 did not. When wereused to immunize mice by the intranasal route, Ad5-R3-sigma produced higher serum and vaginal antibody responses than Ad5. These data suggest optimized Ad-sigma vectors may be useful vectors for mucosal vaccination. - Highlights: • Constructed adenoviruses (Ads) displaying different reovirus sigma 1 fusion proteins. • Progressively longer chimeras were more poorly encapsidated onto Ad virions. • Ad5-R3-sigma mediated better systemic and mucosal immune responses than Ad5.

  19. Mucosal vaccination by adenoviruses displaying reovirus sigma 1

    International Nuclear Information System (INIS)

    Weaver, Eric A.; Camacho, Zenaido T.; Hillestad, Matthew L.; Crosby, Catherine M.; Turner, Mallory A.; Guenzel, Adam J.; Fadel, Hind J.; Mercier, George T.; Barry, Michael A.

    2015-01-01

    We developed adenovirus serotype 5 (Ad5) vectors displaying the sigma 1 protein from reovirus as mucosal vaccines. Ad5-sigma retargets to JAM-1 and sialic acid, but has 40-fold reduced gene delivery when compared to Ad5. While weaker at transduction, Ad5-sigma generates stronger T cell responses than Ad5 when used for mucosal immunization. In this work, new Ad5-fiber-sigma vectors were generated by varying the number of fiber β-spiral shaft repeats (R) between the fiber tail and sigma. Increasing chimera length led to decreasing insertion of these proteinsAd5 virions. Ad-R3 and R14 vectors effectively targeted JAM-1 in vitro while R20 did not. When wereused to immunize mice by the intranasal route, Ad5-R3-sigma produced higher serum and vaginal antibody responses than Ad5. These data suggest optimized Ad-sigma vectors may be useful vectors for mucosal vaccination. - Highlights: • Constructed adenoviruses (Ads) displaying different reovirus sigma 1 fusion proteins. • Progressively longer chimeras were more poorly encapsidated onto Ad virions. • Ad5-R3-sigma mediated better systemic and mucosal immune responses than Ad5

  20. Study of the reactions $\\bar{p}p \\rightarrow \\bar{\\Lambda} \\Lambda , \\bar{\\Lambda} \\Sigma^{0}$ or $\\bar{\\Sigma^{0}} \\Lambda , \\bar{\\Sigma^{+}} \\Sigma^{+}$ at 3.6 GeV/c

    CERN Document Server

    Atherton, Henry W; Moebes, J P; Quercigh, Emanuele

    1974-01-01

    The reactions $\\bar{p}p \\rightarrow \\bar{\\Lambda} \\Lambda , \\bar{\\Lambda} \\Sigma^{0}$ or $\\bar{\\Sigma^{0}} \\Lambda , \\bar{\\Sigma^{+}} \\Sigma^{+}$ are studied at an incident momentum of 3.6 GeV/c in a 35.4 event/$\\mu$ b experiment performed in the CERN 2m HBC. Total and differential cross sections are presented. The polarization of the hyperons is measured as a function of $t$ and for the reaction $\\bar{p}p \\rightarrow \\bar{\\Lambda} \\Lambda$ the complete spin correlation matrix is given. (23 refs).

  1. Precipitation Mechanism of Sigma Phase in Super Duplex Stainless Steels

    Science.gov (United States)

    Nakade, Katsuyuki; Kuroda, Toshio

    The influence of alloying elements on the precipitation behavior of sigma (σ) phase was investigated for conventional SAF2205 and SAF2507 super duplex stainless steel. Time-Temperature-Precipitation (T-T-P) diagram of sigma phase of SAF2507 were shifted toward to shorter times compared to SAF2205. The precipitation of sigma phase was accelerated with increasing Cr and Mo concentration. According to the microstructure observation, the sigma phase began to precipitate at ferrite (α) ⁄ austenite (γ) phase boundaries and grew into ferrite for SAF2507 and SAF2205 steel. In the as-received condition, Cr and Mo concentration in ferrite was clearly higher than that in austenite. Especially, it was found that Mo concentration in ferrite of SAF2507 was higher than that in ferrite of SAF2205. The result of EPMA-measurement showed that sigma phase was mainly Fe-Cr-Mo intermetallic compound and Mo was significantly enriched into sigma phase. The difference of Mo concentration in ferrite significantly affected to the sigma phase precipitation. The secondary austenite formation was also induced by sigma phase precipitation. Cr and Mo were ejected to the remained ferrite ⁄ austenite phase boundaries by secondary austenite formation. Consequently, sigma phase precipitation was more accelerated by the reheating.

  2. Getting the sigma in the M_BH - sigma relation right

    Science.gov (United States)

    van der Marel, Roeland

    2017-08-01

    The relation between the mass of the central supermassive black hole (M_BH) and the velocity dispersion of its host spheroid (sigma) is fundamental for our understanding of galaxy evolution and its relation to their nuclei. Correspondingly many HST orbits have been invested in determining accurate M_BH masses. Surprisingly little has been done on standardizing the other axis, i.e. sigma measurements. These values are often derived from various long-slit datasets at different physical radii of the galaxy and no homogeneous definition has been given. We propose to remedy this situation by using our dataset of MUSE and PPAK kinematic maps out to 1 R_e of galaxies with a secure black hole mass. These data are useful for large scale kinematics, however, obtaining velocity dispersions at small radii is not possible. To measure velocity dispersions at small radii we require high-spatial resolution spectroscopy as provided by HST/STIS. In addtion, high-resolution photometric data is needed to define consistent apertures in each galaxy. We therefore propose to use the unique capabilities of HST and harvest years of efforts to collect archival spectroscopic and imaging data for BH host galaxies. This will allow creating a catalog of sigma values, calculated in various ways and at various radii and to re-calibrate the M_BH - sigma relation.

  3. 300-MHz optical discriminator-counter

    International Nuclear Information System (INIS)

    Turko, B.; Lo, C.C.

    1981-07-01

    The prediction of future CO 2 content in the atmosphere is not completely credible because the oceanographers and terrestrial ecologists do not agree on the global CO 2 balance. Very precise measurements of O 2 /N 2 ratio using Raman scattering over a few years' period could provide important information and lead to the explanation of the disparity in the atmospheric CO 2 balance. An optical discriminator-counter has been developed to count closely spaced optical events in the few photon level. Simulated optical events as close as 2.5 ns apart had been positively detected by using selected photomultipliers and optimized discriminators. Testing of the optical discriminator-counter was done by using an electrical pulse pair spaced 3 ns apart and also by a similar optical pulse pair generated by fast light-emitting diode. The photomultiplier is capable of counting an average single photoelectron pulse frequency of 50 MHz and has a sensitive detecting area of 50 mm in diameter. The discriminator performance is discussed

  4. 500 MHz transient digitizers based on GaAs CCDs

    International Nuclear Information System (INIS)

    Bryman, D.A.; Constable, M.; Cresswell, J.V.; Daviel, A.; LeNoble, M.; Mildenberger, J.; Poutissou, R.

    1996-11-01

    A system of 500 MHz transient digitizers based on gallium arsenide resistive gate charged coupled devices has been developed for an experiment studying rare K decays. CCDs with dynamic range of 8-bits and 128 or 320 pixels are used as analog pipelines. The CCD's are driven by a single phase transport system. Data readout and manipulation occurs at 15.6 MHz. (authors)

  5. A Continuous-Time Delta-Sigma ADC for Portable Ultrasound Scanners

    DEFF Research Database (Denmark)

    Llimos Muntal, Pere; Jørgensen, Ivan Harald Holger; Bruun, Erik

    2017-01-01

    A fully differential fourth-order 1-bit continuous-time delta-sigma ADC designed in a 65nm process for portable ultrasound scanners is presented in this paper. The circuit design, implementation and measurements on the fabricated die are shown. The loop filter consists of RC-integrators, programmable...... capacitor arrays, resistors and voltage feedback DACs. The quantizer contains a pulse generator, a high-speed clocked comparator and a pull-down clocked latch to ensure constant delay in the feedback loop. Using this implementation, a small and low-power solution required for portable ultrasound scanner...... applications is achieved. The converter has a supply voltage of 1.2V, a bandwidth of 10MHz and an oversampling ratio of 16 leading to an operating frequency of 320MHz. The design occupies a die area of 0.0175mm2. Simulations with extracted parasitics show a SNR of 45.2dB and a current consumption of 489 µ...

  6. A 70 MHz pulsing beam system for protons

    International Nuclear Information System (INIS)

    An Shizhong; Zhang Tianjue; Wu Longcheng; Lv Yinlong; Song Guofang; Guan Fengping; Jia Xianlu

    2008-01-01

    A test beam line for pulsed beam generation for 10 MeV central region model (CRM) of a compact cyclotron is under construction as China Institute of Atomic Energy (CIAE). A 70 MHz continuous H - beam with the energy of dozens of keV or a hundred keV will be pulsed to pulse length of less than 10 ns with the repetition rate of 1-8 MHz. A 70.487 MHz buncher will be used to compress the DC beam into the RF phase acceptance of ±30° of the CRM cyclotron. The 2.2 MHz sine waveform will be used for the chopper. A pulse with the repetition rate to 4.4 MHz and pulse length less than 10 ns is expected after CRM cyclotron. (authors)

  7. Integrated design of SIGMA uranium enrichment plants

    International Nuclear Information System (INIS)

    Rivarola, Martin E.; Brasnarof, Daniel O.

    1999-01-01

    In the present work, we describe a preliminary analysis of the design feedbacks in a Uranium Enrichment Plant, using the SIGMA concept. Starting from the result of this analysis, a computer code has been generated, which allows finding the optimal configurations of plants, for a fixed production rate. The computer code developed includes the model of the Thermohydraulic loop of a SIGMA module. The model contains numerical calculations of the main components of the circuit. During the calculations, the main components are dimensioned, for a posterior cost compute. The program also makes an estimation of the enrichment gain of the porous membrane, for each separation stage. Once the dimensions of the main components are known, using the enrichment cascade calculation, the capital and operation costs of the plant could be determined. At this point it is simple to calculate a leveled cost of the Separative Work Unit (SWU). A numerical optimizer is also included in the program. This optimizer finds the optimal cascade configuration, for a given set of design parameters. The whole-integrated program permits to investigate in detail the feedback in the component design. Therefore, the sensibility of the more relevant parameters can be computed, with respect of the economical variables of the plant. (author)

  8. Development of simple band-spectral pyranometer and quantum meter using photovoltaic cells and bandpass filters

    Energy Technology Data Exchange (ETDEWEB)

    Bilguun, Amarsaikhan, E-mail: bilguun@pes.ee.tut.ac.jp; Nakaso, Tetsushi; Harigai, Toru; Suda, Yoshiyuki; Takikawa, Hirofumi, E-mail: takikawa@ee.tut.ac.jp [Toyohashi University of Technology, 1-1 Habarigaoka, Tempaku, Toyohashi 441-8580 (Japan); Tanoue, Hideto [Kitakyushu National College of Technology, 5-20-1, Kokuraminami, Kitakyushu, Fukuoka 802-0985 (Japan)

    2016-02-01

    In recent years, greenhouse automatic-control, based on the measurement of solar irradiance, has been attracting attention. This control is an effective method for improving crop production. In the agricultural field, it is necessary to measure Photon Flux Density (PFD), which is an important parameter in the promotion of plant growth. In particular, the PFD of Photosynthetically Active Radiation (PAR, 400-700 nm) and Plant Biologically Active Radiation (PBAR, 300-800 nm) have been discussed in agricultural plant science. The commercial quantum meter (QM, PAR meter) can only measure Photosynthetically Photon Flux Density (PPFD) which is the integrated PFD quantity on the PAR wavelength. In this research, a band-spectral pyranometer or quantum meter using PVs with optical bandpass filters for dividing the PBAR wavelength into 100 nm bands (five independent channels) was developed. Before field testing, calibration of the instruments was carried out using a solar simulator. Next, a field test was conducted in three differing weather conditions such as clear, partly cloudy and cloudy skies. As a result, it was found that the response rate of the developed pyranometer was faster by four seconds compared with the response rate of the commercial pyranometer. Moreover, the outputs of each channel in the developed pyranometer were very similar to the integrated outputs of the commercial spectroradiometer. It was confirmed that the solar irradiance could be measured in each band separately using the developed band-spectral pyranometer. It was indicated that the developed band-spectral pyranometer could also be used as a PV band-spectral quantum meter which is obtained by converting the band irradiance into band PFD.

  9. Auditory stream segregation using bandpass noises: evidence from event-related potentials

    Directory of Open Access Journals (Sweden)

    Yingjiu eNie

    2014-09-01

    Full Text Available The current study measured neural responses to investigate auditory stream segregation of noise stimuli with or without clear spectral contrast. Sequences of alternating A and B noise bursts were presented to elicit stream segregation in normal-hearing listeners. The successive B bursts in each sequence maintained an equal amount of temporal separation with manipulations introduced on the last stimulus. The last B burst was either delayed for 50% of the sequences or not delayed for the other 50%. The A bursts were jittered in between every two adjacent B bursts. To study the effects of spectral separation on streaming, the A and B bursts were further manipulated by using either bandpass-filtered noises widely spaced in center frequency or broadband noises. Event-related potentials (ERPs to the last B bursts were analyzed to compare the neural responses to the delay vs. no-delay trials in both passive and attentive listening conditions. In the passive listening condition, a trend for a possible late mismatch negativity (MMN or late discriminative negativity (LDN response was observed only when the A and B bursts were spectrally separate, suggesting that spectral separation in the A and B burst sequences could be conducive to stream segregation at the pre-attentive level. In the attentive condition, a P300 response was consistently elicited regardless of whether there was spectral separation between the A and B bursts, indicating the facilitative role of voluntary attention in stream segregation. The results suggest that reliable ERP measures can be used as indirect indicators for auditory stream segregation in conditions of weak spectral contrast. These findings have important implications for cochlear implant (CI studies – as spectral information available through a CI device or simulation is substantially degraded, it may require more attention to achieve stream segregation.

  10. Development of simple band-spectral pyranometer and quantum meter using photovoltaic cells and bandpass filters

    Science.gov (United States)

    Bilguun, Amarsaikhan; Nakaso, Tetsushi; Harigai, Toru; Suda, Yoshiyuki; Takikawa, Hirofumi; Tanoue, Hideto

    2016-02-01

    In recent years, greenhouse automatic-control, based on the measurement of solar irradiance, has been attracting attention. This control is an effective method for improving crop production. In the agricultural field, it is necessary to measure Photon Flux Density (PFD), which is an important parameter in the promotion of plant growth. In particular, the PFD of Photosynthetically Active Radiation (PAR, 400-700 nm) and Plant Biologically Active Radiation (PBAR, 300-800 nm) have been discussed in agricultural plant science. The commercial quantum meter (QM, PAR meter) can only measure Photosynthetically Photon Flux Density (PPFD) which is the integrated PFD quantity on the PAR wavelength. In this research, a band-spectral pyranometer or quantum meter using PVs with optical bandpass filters for dividing the PBAR wavelength into 100 nm bands (five independent channels) was developed. Before field testing, calibration of the instruments was carried out using a solar simulator. Next, a field test was conducted in three differing weather conditions such as clear, partly cloudy and cloudy skies. As a result, it was found that the response rate of the developed pyranometer was faster by four seconds compared with the response rate of the commercial pyranometer. Moreover, the outputs of each channel in the developed pyranometer were very similar to the integrated outputs of the commercial spectroradiometer. It was confirmed that the solar irradiance could be measured in each band separately using the developed band-spectral pyranometer. It was indicated that the developed band-spectral pyranometer could also be used as a PV band-spectral quantum meter which is obtained by converting the band irradiance into band PFD.

  11. Development of simple band-spectral pyranometer and quantum meter using photovoltaic cells and bandpass filters

    International Nuclear Information System (INIS)

    Bilguun, Amarsaikhan; Nakaso, Tetsushi; Harigai, Toru; Suda, Yoshiyuki; Takikawa, Hirofumi; Tanoue, Hideto

    2016-01-01

    In recent years, greenhouse automatic-control, based on the measurement of solar irradiance, has been attracting attention. This control is an effective method for improving crop production. In the agricultural field, it is necessary to measure Photon Flux Density (PFD), which is an important parameter in the promotion of plant growth. In particular, the PFD of Photosynthetically Active Radiation (PAR, 400-700 nm) and Plant Biologically Active Radiation (PBAR, 300-800 nm) have been discussed in agricultural plant science. The commercial quantum meter (QM, PAR meter) can only measure Photosynthetically Photon Flux Density (PPFD) which is the integrated PFD quantity on the PAR wavelength. In this research, a band-spectral pyranometer or quantum meter using PVs with optical bandpass filters for dividing the PBAR wavelength into 100 nm bands (five independent channels) was developed. Before field testing, calibration of the instruments was carried out using a solar simulator. Next, a field test was conducted in three differing weather conditions such as clear, partly cloudy and cloudy skies. As a result, it was found that the response rate of the developed pyranometer was faster by four seconds compared with the response rate of the commercial pyranometer. Moreover, the outputs of each channel in the developed pyranometer were very similar to the integrated outputs of the commercial spectroradiometer. It was confirmed that the solar irradiance could be measured in each band separately using the developed band-spectral pyranometer. It was indicated that the developed band-spectral pyranometer could also be used as a PV band-spectral quantum meter which is obtained by converting the band irradiance into band PFD

  12. Quantitative application of sigma metrics in medical biochemistry.

    Science.gov (United States)

    Nanda, Sunil Kumar; Ray, Lopamudra

    2013-12-01

    Laboratory errors are result of a poorly designed quality system in the laboratory. Six Sigma is an error reduction methodology that has been successfully applied at Motorola and General Electric. Sigma (σ) is the mathematical symbol for standard deviation (SD). Sigma methodology can be applied wherever an outcome of a process has to be measured. A poor outcome is counted as an error or defect. This is quantified as defects per million (DPM). A six sigma process is one in which 99.999666% of the products manufactured are statistically expected to be free of defects. Six sigma concentrates, on regulating a process to 6 SDs, represents 3.4 DPM (defects per million) opportunities. It can be inferred that as sigma increases, the consistency and steadiness of the test improves, thereby reducing the operating costs. We aimed to gauge performance of our laboratory parameters by sigma metrics. Evaluation of sigma metrics in interpretation of parameter performance in clinical biochemistry. The six month internal QC (October 2012 to march 2013) and EQAS (external quality assurance scheme) were extracted for the parameters-Glucose, Urea, Creatinine, Total Bilirubin, Total Protein, Albumin, Uric acid, Total Cholesterol, Triglycerides, Chloride, SGOT, SGPT and ALP. Coefficient of variance (CV) were calculated from internal QC for these parameters. Percentage bias for these parameters was calculated from the EQAS. Total allowable errors were followed as per Clinical Laboratory Improvement Amendments (CLIA) guidelines. Sigma metrics were calculated from CV, percentage bias and total allowable error for the above mentioned parameters. For parameters - Total bilirubin, uric acid, SGOT, SGPT and ALP, the sigma values were found to be more than 6. For parameters - glucose, Creatinine, triglycerides, urea, the sigma values were found to be between 3 to 6. For parameters - total protein, albumin, cholesterol and chloride, the sigma values were found to be less than 3. ALP was the best

  13. Imaging melanin cancer growth in-vivo using raster-scan optoacoustic mesoscopy (RSOM) at 50 MHz and 100 MHz

    Science.gov (United States)

    Omar, Murad; Schwarz, Mathias; Soliman, Dominik; Symvoulidis, Panagiotis; Ntziachristos, Vasilis

    2016-03-01

    We used raster-scan optoacoustic mesoscopy (RSOM) at 50 MHz, and at 100 MHz, to monitor tumor growth, and tumor angiogenesis, which is a central hallmark of cancer, in-vivo. In this study we compared the performance, and the effect of the 50 MHz, and the 100 MHz frequencies on the quality of the final image. The system is based on a reflection-mode implementation of RSOM. The detectors used are custom made, ultrawideband, and spherically focused. The use of such detectors enables light coupling from the same side as the detector, thus reflection-mode. Light is in turn coupled using a fiber bundle, and the detector is raster scanned in the xy-plane. Subsequently, to retrieve small features, the raw data are reconstructed using a multi-bandwidth, beamforming reconstruction algorithm. Comparison of the system performance at the different frequencies shows as expected a higher resolution in case of the 100 MHz detector compared to the 50 MHz. On the other hand the 50 MHz has a better SNR, can detect features from deeper layers, and has higher angular acceptance. Based on these characteristics the 50 MHz detector was mostly used. After comparing the performance we monitored the growth of B16F10 cells, melanin tumor, over the course of 9 days. We see correspondence between the optoacoustic measurements and the cryoslice validations. Additionally, in areas close to the tumor we see sprouting of new vessels, starting at day 4-5, which corresponds to tumor angiogenesis.

  14. The sigma(54) regulon (sigmulon) of Pseudomonas putida

    DEFF Research Database (Denmark)

    Cases, I.; Ussery, David; de Lorenzo, V.

    2003-01-01

    , the sigma(54) regulon has been studied both in Escherichia coli, Salmonella typhimurium and several species of the Rhizobiaceae. Here we present the analysis of the sigma(54) regulon (sigmulon) in the complete genome of Pseudomonas putida KT2440. We have developed an improved method for the prediction...

  15. Sigma-1 receptor: The novel intracellular target of neuropsychotherapeutic drugs

    Directory of Open Access Journals (Sweden)

    Teruo Hayashi

    2015-01-01

    Full Text Available Sigma-1 receptor ligands have been long expected to serve as drugs for treatment of human diseases such as neurodegenerative disorders, depression, idiopathic pain, drug abuse, and cancer. Recent research exploring the molecular function of the sigma-1 receptor started unveiling underlying mechanisms of the therapeutic activity of those ligands. Via the molecular chaperone activity, the sigma-1 receptor regulates protein folding/degradation, ER/oxidative stress, and cell survival. The chaperone activity is activated or inhibited by synthetic sigma-1 receptor ligands in an agonist-antagonist manner. Sigma-1 receptors are localized at the endoplasmic reticulum (ER membranes that are physically associated with the mitochondria (MAM: mitochondria-associated ER membrane. In specific types of neurons (e.g., those at the spinal cord, sigma-1 receptors are also clustered at ER membranes that juxtapose postsynaptic plasma membranes. Recent studies indicate that sigma-1 receptors, partly in sake of its unique subcellular localization, regulate the mitochondria function that involves bioenergetics and free radical generation. The sigma-1 receptor may thus provide an intracellular drug target that enables controlling ER stress and free radical generation under pathological conditions.

  16. Inspanning om Lean Six Sigma op kaart te zetten beloond

    NARCIS (Netherlands)

    Does, R.J.M.M.

    2008-01-01

    Prof.dr. R.J.M.M. Does is al jarenlang een fervent voorvechter voor het gebruik van statistiek. En meer recent is hij zo’n beetje de belichaming van (Lean) Six Sigma in Europa. Tal van grote organisaties hebben hem te hulp geroepen bij de invoering van (Lean) Six Sigma. Het is dan ook niet meer dan

  17. Lean Six Sigma in het ziekenhuis: De beschikbaarheid van infuuspompen

    NARCIS (Netherlands)

    Does, R.J.M.M.; Kemper, B.P.H.; Koopmans, M.

    2011-01-01

    In het topklinisch ziekenhuis Medisch Spectrum Twente werd in 2008 een Lean Six Sigma-project gestart. Het doel was vermindering van operationele kosten van infuuspompen. Het is een interessant voorbeeld van Lean Six Sigma in de gezondheidszorg, omdat het laat zien dat kostenbesparing niet hoeft te

  18. Comparing nonmanufacturing with traditional applications of Six Sigma

    NARCIS (Netherlands)

    Does, R.J.M.M.; Heuvel, van den E.R.; Mast, de J.; Bisgaard, S.

    2002-01-01

    The Six Sigma approach has in the past been predominantly used to improve manufacturing processes. However, Six Sigma is now increasingly applied to a wide variety of nonmanufacturing operations also. This is an important development—there are potentially more benefits to be achieved in those areas

  19. Six sigma management and its application in nuclear power plant

    International Nuclear Information System (INIS)

    Liu Weihua; Tong Lili

    2007-01-01

    Six sigma management mode is presented. The feasibility, necessity and the steps to extend six sigma in nuclear power plant are addressed. Nuclear power plant can eliminate or decrease human errors through importing six management concept, the 'zero disfigurement' quality and operation can achieved, decreasing accident risk and realizing safety operation. (authors)

  20. A construction of observables for AKSZ sigma models

    OpenAIRE

    Mnev, Pavel

    2012-01-01

    A construction of gauge-invariant observables is suggested for a class of topological field theories, the AKSZ sigma-models. The observables are associated to extensions of the target Q-manifold of the sigma model to a Q-bundle over it with additional Hamiltonian structure in fibers.

  1. A Geographical Information System for Malaria in Colombia (SIGMA)

    International Nuclear Information System (INIS)

    Poveda, German; Hernandez, Olver; Urquijo, Lenis; Padilla Julio Cesar

    2005-01-01

    A Geographical Information System for Malaria in Colombia (SIGMA) is introduced and its capabilities and modules are described. It allows the interactive visualization of the Colombian Ministry of Social Protection database at national, regional and municipal levels and the analysis of relationships with different environmental and climatic variables. SIGMA is a powerful decision support system for human health intervention and management programs in Colombia

  2. An application of six sigma for SMEs: A case study

    Directory of Open Access Journals (Sweden)

    Prabhakar Kaushik

    2017-03-01

    Full Text Available Six Sigma is the concept of improving the quality by reducing process variations, making con-tinuous improvements, reducing defect rates and improving the processes. Initially, the concept of Six Sigma focused on defect reduction, cost reduction and value addition. Fundamentally the basic idea of Six Sigma is to improve the process-capability and making the process more relia-ble along with reducing wastes within industries. Evaluation the implication of applying Six Sigma over the small and medium-sized enterprises is the main purpose of this research work taking a particular case of automobile industries. In the present work, DMAIC methodology of Six Sigma is used to a small seat slider lock nut manufacturing unit to reduce the play issue in K2 seat slider lock in automobile units by reducing defects inherent in the process. After apply-ing Six Sigma methodology, it was found that manufacturing units could earn profits in terms of reducing the wastage as well as improving the quality standard of the product by controlling the play issue in seat slider lock nut mechanism. Result shows that with the application of Six Sig-ma, process, sigma level brought up to 5.53σ from 1.59σ by varying the seat slider lock nut di-mensions/size.

  3. Studi Implementasi Six Sigma dalam Sistem Inventori Galangan Kapal

    Directory of Open Access Journals (Sweden)

    Elwin Elwin

    2012-09-01

    Full Text Available Dalam industri galangan kapal terdapat bahan baku, barang dalam proses dan barang jadi yang merupakan macam-macam bentuk dari persediaan dan berhubungan dengan stok, ketika persediaan tidak dikelola dengan benar maka akan terjadi pembengkakkan biaya/pengeluaran biaya yang tidak dibutuhkan. Tugas akhir ini bertujuan untuk mengetahui kondisi inventori di PT. Dok dan Perkapalan Surbaya, untuk mengetahui faktor-faktor yang menjadi penyebab terjadinya variabilitas output six sigma dan mengurangi defect pada sistem inventori dengan menggunakan metode six sigma DMAIC (Define, Measure, Analyze, Improve dan Control,. Berdasarkan perhitungan Material Pipa mengalami defect sebesar 50.98% dengan nilai sigma 1.48, Material Elbow mengalami defect sebesar 89.80% dengan nilai sigma 0.33, Material Flange mengalami defect sebesar 71.99% dengan nilai sigma 0.90, Material Paking mengalami defect sebesar 13.12% dengan nilai sigma 2.74 dan Material Mur mengalami defect sebesar 17.26% dengan nilai sigma 2.57. Sesuai dengan perhitungan reorder point for the inventory untuk masing-masing material, maka dapat diketahui bahwa material Pipa reoder point adalah 58 lonjor, elbow 100 buah, flange 168 buah, paking 24 buah dan mur 946 buah. Nilai sigma yang diperoleh dalam perhitungan tingkat persediaan masih jauh dari nilai yang seharusnya dapat dicapai oleh suatu perusahaan (6σ, sehingga dilakukan tahap Improve dengan metode Failure Mode and Effect Analysis (FMEA, pembuat SOP Pengendalian persediaan material dengan format baru serta galangan perlu melakukan perhitungan reorder point.  

  4. Logistics services and Lean Six Sigma implementation: a case study

    NARCIS (Netherlands)

    Gutierrez Gutierrez, L.; de Leeuw, S.L.J.M.; Dubbers, R.

    2016-01-01

    Purpose: This paper aims to analyze the application of Lean Six Sigma (LSS) framework for supporting continuous improvement (CI) in logistics services. Both the lean philosophy and the Six Sigma methodology have become two of the most important initiatives for CI in organizations. The combination of

  5. An application of Lean Six Sigma in a hospital

    NARCIS (Netherlands)

    van den Heuvel, J.; Does, R.J.M.M.; de Koning, H.; Anthony, J.; Kumar, M.

    2007-01-01

    Abstract Healthcare today faces major challenges. Patients demand quality of care to be improved continuously. Insurance companies demand the lowest possible prices. Lean Six Sigma is a tool that can help healthcare providers to achieve these at least partly conflicting goals. Lean Six Sigma is an

  6. Evaluation Of Electromagnetic Fields For Frequencies 900 MHz-1 800 MHz In Tirana

    Directory of Open Access Journals (Sweden)

    Kuqi Dhurata

    2015-07-01

    Full Text Available Abstract The massive use of mobile phone as a communication tool nowadays is accompanied the ever increasing interest of the public and researchers for the possibly impact on human health as a result of exposure to the electromagnetic fields that accompany these devices. Therefore knowing the level of exposure electromagnetic fields of this electronic equipment has been and will be in the future interest object to the public and the subject of study for the researchers. In this paper are presents the results of measurements of electromagnetic fields for the frequencies 900 MHz - 1800 MHz used in mobile telephone in Tirana. These frequencies are included in the area radio frequency RF and Microwave MW 300 Hz - 300 GHz in the spectrum of electromagnetic waves and belong to non-ionizing radiation. The measurements were performed in different areas of Tirana. The purpose is to assess the level of exposure electromagnetic fields especially near areas where mobile antennas are mounted construction of dynamic digital mapping and comparison with the permitted levels of the exposure defined by the International Commission of Non Ionizing Radiation Protection ICNIRP. Through this publication the aim of the authors is to provide real information and reliable for the population.

  7. Technology development of solid state rf systems at 350 MHz and 325 MHz for RF accelerator

    International Nuclear Information System (INIS)

    Rama Rao, B.V.; Mishra, J.K.; Pande, Manjiri; Gupta, S.K.

    2011-01-01

    For decades vacuum tubes and klystrons have been used in high power application such as RF accelerators and broadcast transmitters. However, now, the solid-state technology can give power output in kilowatt regime. Higher RF power output can be achieved by combining several solid-state power amplifier modules using power combiners. This technology presents several advantages over traditional RF amplifiers, such as simpler start-up procedure, high modularity, high redundancy and flexibility, elimination of high voltage supplies and high power circulators, low operational cost, online maintenance without shut down of RF power station and no warm up time. In BARC, solid state amplifier technology development is being done both at 350 MHz and 325 MHz using RF transistors such as 1 kW LDMOS and 350 Watt VDMOS. Topology of input and output matching network in RF modules developed, consist of two L type matching sections with each section having a combination of series micro-strip line and parallel capacitor. The design is of equal Q for both the sections and of 25 ohm characteristics impedance of micro strip lines. Based on this, lengths of micro strips lines and values of shunt capacitors have been calculated. The calculated and simulated values of network elements have been compared. Similarly power combiners have been designed and developed based on Wilkinson techniques without internal resistors and using coaxial technology. This paper presents design and development of RF power amplifier modules, associated power combiner technologies and then integrated RF power amplifier. (author)

  8. (-)PPAP: a new and selective ligand for sigma binding sites.

    Science.gov (United States)

    Glennon, R A; Battaglia, G; Smith, J D

    1990-11-01

    Most agents employed for the investigation of sigma (sigma) binding sites display relatively low affinity for these sites, bind both at sigma sites and at either phencyclidine (PCP) sites or dopamine receptors with similar affinity, and/or produce some dopaminergic activity in vivo. We describe a new agent, (-)PPAP or R(-)-N-(3-phenyl-n-propyl)-1-phenyl-2-aminopropane hydrochloride, that binds with high affinity and selectivity at sigma (IC50 = 24 nM) versus either PCP sites (IC50 greater than 75,000 nM) or D1 and D2 dopamine receptors (IC50 greater than 5,000 nM). The sigma affinity of this agent is comparable to that of the standard ligands (+)-3-PPP and DTG. Furthermore, although (-)PPAP is structurally related to amphetamine, it neither produces nor antagonizes amphetamine-like stimulus effect in rats trained to discriminate 1 mg/kg of S(+)amphetamine from saline.

  9. Lean six sigma case studies in the healthcare enterprise

    CERN Document Server

    Furterer, Sandra L

    2014-01-01

    This book provides a detailed description of how to apply Lean Six Sigma in the health care industry, with a special emphasis on process improvement and operations management in hospitals.  The book begins with a description of the Enterprise Performance Excellence (EPE) improvement methodology developed by the author that links several methodologies including systems thinking, theory of constraints, Lean and Six Sigma to provide an enterprise-wide prioritization and value-chain view of health care. The EPE methodology helps to improve flow at the macro or value-chain level, and then identifies Lean Six Sigma detailed improvements that can further improve processes within the value-chain.  The book also provides real-world health care applications of the EPE and Lean Six Sigma methodologies that showed significant results on throughput, capacity, operational and financial performance. The Enterprise Performance Excellence methodology is described, and also the Six Sigma DMAIC (Define-Measure-Analyze-Improve...

  10. Development of radiolabeled probes directed against sigma-1 receptors

    International Nuclear Information System (INIS)

    Ogawa, Kazuma; Masuda, Ryohei; Shiba, Kazuhiro

    2017-01-01

    It has been reported that sigma-1 receptors regulate the release of signaling substances in the central nervous systems and are related to various diseases, such as schizophrenia, stress disorders, dementia, amyotrophic lateral sclerosis (ALS), and cancer. If the quantification of the sigma-1 receptors is possible, the pathophysiology, the stage, and the early detection of the diseases could be understandable. Molecular imaging using Positron Emission Tomography (PET) or Single Photon Emission Computed Tomography (SPECT) and radioactive probes makes noninvasive quantification of the in vivo metabolism and function possible. Currently, only nuclear medicine diagnosis using PET or SPECT can quantify the sigma-1 receptors. Therefore, there is great expectation for the development of molecular probes to image the sigma-1 receptors specifically. In this paper, we introduce our research on the development of radiohalogen-labeled molecular probes directed against the sigma-1 receptors. (author)

  11. Nambu sigma model and effective membrane actions

    Energy Technology Data Exchange (ETDEWEB)

    Jurco, Branislav, E-mail: jurco@karlin.mff.cuni.cz [Mathematical Institute, Charles University, Prague 186 75 (Czech Republic); Schupp, Peter, E-mail: p.schupp@jacobs-university.de [Jacobs University Bremen, 28759 Bremen (Germany); Maxwell Institute for Mathematical Sciences, Heriot-Watt University, Edinburgh, EH14 4AS, Scotland (United Kingdom)

    2012-07-09

    We propose an effective action for a p{sup Prime }-brane with open p-branes ending on it. The action has dual descriptions similar to the commutative and non-commutative ones of the DBI action for D-branes and open strings. The Poisson structure governing the non-commutativity of the D-brane is replaced by a Nambu structure and the open-closed string relations are generalized to the case of p-branes utilizing a novel Nambu sigma model description of p-branes. In the case of an M5-brane our action interpolates between M5-actions already proposed in the literature and matrix-model like actions involving Nambu structures.

  12. Nambu sigma model and effective membrane actions

    International Nuclear Information System (INIS)

    Jurčo, Branislav; Schupp, Peter

    2012-01-01

    We propose an effective action for a p ′ -brane with open p-branes ending on it. The action has dual descriptions similar to the commutative and non-commutative ones of the DBI action for D-branes and open strings. The Poisson structure governing the non-commutativity of the D-brane is replaced by a Nambu structure and the open-closed string relations are generalized to the case of p-branes utilizing a novel Nambu sigma model description of p-branes. In the case of an M5-brane our action interpolates between M5-actions already proposed in the literature and matrix-model like actions involving Nambu structures.

  13. Potentialities of a new sigma(+)-sigma(-)laser configuration for radiative cooling and trapping

    Energy Technology Data Exchange (ETDEWEB)

    Dalibard, J; Reynaud, S; Cohen-Tannoudji, C

    1984-11-28

    In the process of cooling and trapping neutral atoms, a new laser configuration is investigated which consists of two counterpropagating laser beams with orthogonal sigma(+) and sigma(-)polarizations. It is shown that such a configuration looks more promising than an ordinary standing wave (where the two counterpropagating waves have the same polarization), and this result is explained as being due to angular momentum conservation which prevents any coherent redistribution of photons between the two waves. The present conclusions are based on a quantitative calculation of the various parameters (potential depth, friction coefficient, diffusion coefficient) describing the mean value and the fluctuations of the radiative forces experienced, in such a laser configuration, by an atom with a J 0 ground state and a J 1 excited state. 30 references.

  14. Production of the $\\Sigma^0_c$ and $\\Sigma^{++}_c$ by High-Energy Neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Ladbury, Raymond, Jr. [Colorado U.

    1988-01-01

    We present the first observation of hadroproduction of the $\\Sigma^{++}_C$ and $\\Sigma^0_c$ , decaying into $\\Lambda_{c\\pi}$. The daughter $\\Lambda_c$ is observed in the decay modes $pK \\pi$ and $pK_s\\pi\\pi$. The Experiment was conducted at a broadband neutron beam in the Proton East area of the Fermi National Accelerator Laboratory. A two - magnet multiparticle spectrometer equipped with proportional wire chambers and a high resolution MWPC vertex detector was used to momentum analyze charged particles produced in the interactions of neutrons on targets of beryllium, silicon and tungsten. Particles were identified using three Cerenkov counters. The beam energy for each event was reconstructed using hadronic and electromagnetic calorimetry....

  15. A 3-D miniaturized high selectivity bandpass filter in LTCC technology

    KAUST Repository

    Arabi, Eyad A.

    2014-01-01

    Transmission zeros are used to improve the roll-off factors of filters but as a consequence, the out-of-band rejection decreases. In this work, an LTCC filter design is presented which employs a series inductor (implemented as a via hole) to improve the out-of-band rejection by introducing a third transmission zero. The filter, designed for GPS band (1.57 GHz), has one of the smallest reported foot prints ((0.063×0.048×0.005)λg) and demonstrates the highest roll off factor (16.7 dB/100 MHz) for this band. With only four LTCC layers, the design is cost effective and thus highly suitable for miniaturized, ultra-thin system-on-package applications. © 2001-2012 IEEE.

  16. Cell death induced by GSM 900-MHz and DCS 1800-MHz mobile telephony radiation

    International Nuclear Information System (INIS)

    Panagopoulos, D. J; Chavdoula, E. D.; Nezis, I. P.; Margaritis, L. H.

    2007-01-01

    In the present study, the TUNEL (Terminal deoxynucleotide transferase dUTP Nick End Labeling) assay '' a well known technique widely used for detecting fragmented DNA in various types of cells'' was used to detect cell death (DNA fragmentation) in a biological model, the early and mid stages of oogenesis of the insect Drosophila melanogaster. The flies were exposed in vivo to either GSM 900-MHz (Global System for Mobile telecommunications) or DCS 1800-MHz (Digital Cellular System) radiation from a common digital mobile phone, for few minutes per day during the first 6 days of their adult life. The exposure conditions were similar to those to which a mobile phone user is exposed, and were determined according to previous studies of ours [D.J. Panagopoulos, A. Karabarbounis, L.H. Margaritis, Effect of GSM 900-MHz mobile phone radiation on the reproductive capacity of D. melanogaster, Electromagn. Biol. Med. 23 (1) (2004) 29''43; D.J. Panagopoulos, N. Messini, A. Karabarbounis, A.L. Philippetis, L.H. Margaritis, Radio frequency electromagnetic radiation within ''safety levels'' alters the physiological function of insects, in: P. Kostarakis, P. Stavroulakis (Eds.), Proceedings of the Millennium International Workshop on Biological Effects of Electromagnetic Fields, Heraklion, Crete, Greece, October 17''20, 2000, pp. 169''175, ISBN: 960-86733-0-5; D.J. Panagopoulos, L.H. Margaritis, Effects of electromagnetic fields on the reproductive capacity of D. melanogaster, in: P. Stavroulakis (Ed.), Biological Effects of Electromagnetic Fields, Springer, 2003, pp. 545''578], which had shown a large decrease in the oviposition of the same insect caused by GSM radiation. Our present results suggest that the decrease in oviposition previously reported, is due to degeneration of large numbers of egg chambers after DNA fragmentation of their constituent cells, induced by both types of mobile telephony radiation. Induced cell death is recorded for the first time, in all types of

  17. A dense grid of narrow bandpass steep edge filters for the JST/T250 telescope: summary of results

    Science.gov (United States)

    Brauneck, U.; Sprengard, R.; Bourquin, S.; Marín-Franch, A.

    2017-09-01

    On the Javalambre mountain in Spain, the Centro de Estudios de Fisica del Cosmos de Aragon (CEFCA) has setup a new wide field telescope, the JST/T250: a 2.55 m telescope with a plate scale of 22.67"/mm and a 3° diameter field of view. To conduct a photometric sky survey, a large format mosaic camera made of 14 individual CCDs is used in combination with filter trays containing 14 filters each of theses 101.7 x 96.5 mm in size. For this instrument, SCHOTT manufactured 56 specially designed steep edged bandpass interference filters which were recently completed. The filter set consists of bandpass filters in the range between 348,5 nm and 910 nm and a longpass filter at 915 nm. Most of the filters have FWHM of 14.5 nm and a blocking between 250 and 1050 nm with optical density of OD5. Absorptive color glass substrates in combination with interference filters were used to minimize residual reflection in order to avoid ghost images. Inspite of containing absorptive elements, the filters show the maximum possible transmission. This was achieved by using magnetron sputtering for the filter coating process. The most important requirement for the continuous photometric survey is the tight tolerancing of the central wavelengths and FWHM of the filters. This insures each bandpass having a defined overlap with its neighbors. In addition, the blocking of the filters is better than OD5 in the range 250-1050 nm. A high image quality required a low transmitted wavefront error (

  18. CAMEX-4 MIPS 915 MHZ DOPPLER WIND PROFILER V1

    Data.gov (United States)

    National Aeronautics and Space Administration — The CAMEX-4 MIPS 915 MHZ Doppler Wind Profiler dataset was collected by the University of Alabama in Huntsville (UAH) Mobile Integrated Profiling System (MIPS),...

  19. CAMEX-4 MIPS 915 MHZ DOPPLER WIND PROFILER V1

    Data.gov (United States)

    National Aeronautics and Space Administration — The University of Alabama in Huntsville (UAH) Mobile Integrated Profiling System (MIPS) is a mobile atmospheric profiling system. It includes a 915 MHz Doppler...

  20. Analog Fiber Optic Link with DC-100 MHz Bandwidth

    National Research Council Canada - National Science Library

    Sullivan, C. A; Girardi, P. G; Lohrmann, Dieter R

    2008-01-01

    An analog fiber optic link covering the frequency range from DC to 100 MHz was designed, constructed, and tested, in order to connect a 10 kA pulse current probe to oscilloscopes for oscillographing...

  1. Modelling and validation of a simple and compact wide upper stop band ultra-wideband bandpass filter

    Directory of Open Access Journals (Sweden)

    Somdotta Roy Choudhury

    2014-09-01

    Full Text Available A compact ultra-wideband (UWB bandpass filter (BPF is proposed based on end coupled microstrip transmission line, defected ground structure and defected microstrip structure. The experimental filter shows a fractional bandwidth of 110% at a centre frequency, with two observable transmission zeros (attenuation poles at 2.1 and 11.7 GHz. Measured results exhibit an UWB passband from 3.02 to 10.6 GHz with mid-band insertion loss of 1.8 dB and group delay variation <0.45 ns. The BPF achieves a wide stopband with < −18 dB attenuation up to 20 GHz.

  2. Particle analysis on concentrated particle suspensions by transmission fluctuation spectrometry with band-pass filters: part 2. Experimental results

    International Nuclear Information System (INIS)

    Xu, Yamin; Shen, Jianqi; Cai, Xiaoshu; Riebel, Ulrich

    2010-01-01

    Transmission fluctuation spectrometry (TFS), as a new method of online and real-time particle analysis developed in recent years, can measure the particle size distribution and particle concentration simultaneously. In the preceding paper, high concentration effects on the TFS using band-pass filters were investigated by numerical simulation, and empirical expressions to correct the effects were obtained. This paper presents a study on the TFS measurements in which the particle concentration varies in a very wide dynamic range. Finally, reasonable results on both the particle size distribution and particle concentration are obtained by introducing empirical corrections into the inversion algorithm

  3. 500 MHz transient digitizers based on GaAs CCDs

    Energy Technology Data Exchange (ETDEWEB)

    Bryman, D A; Constable, M; Cresswell, J V; Daviel, A; LeNoble, M; Mildenberger, J; Poutissou, R

    1996-11-01

    A system of 500 MHz transient digitizers based on gallium arsenide resistive gate charged coupled devices has been developed for an experiment studying rare K decays. CCDs with dynamic range of 8-bits and 128 or 320 pixels are used as analog pipelines. The CCD`s are driven by a single phase transport system. Data readout and manipulation occurs at 15.6 MHz. (authors). 12 refs., 15 figs.

  4. Application of Six Sigma towards improving surgical outcomes.

    Science.gov (United States)

    Shukla, P J; Barreto, S G; Nadkarni, M S

    2008-01-01

    Six Sigma is a 'process excellence' tool targeting continuous improvement achieved by providing a methodology for improving key steps of a process. It is ripe for application into health care since almost all health care processes require a near-zero tolerance for mistakes. The aim of this study is to apply the Six Sigma methodology into a clinical surgical process and to assess the improvement (if any) in the outcomes and patient care. The guiding principles of Six Sigma, namely DMAIC (Define, Measure, Analyze, Improve, Control), were used to analyze the impact of double stapling technique (DST) towards improving sphincter preservation rates for rectal cancer. The analysis using the Six Sigma methodology revealed a Sigma score of 2.10 in relation to successful sphincter preservation. This score demonstrates an improvement over the previous technique (73% over previous 54%). This study represents one of the first clinical applications of Six Sigma in the surgical field. By understanding, accepting, and applying the principles of Six Sigma, we have an opportunity to transfer a very successful management philosophy to facilitate the identification of key steps that can improve outcomes and ultimately patient safety and the quality of surgical care provided.

  5. The 136 MHz/400 MHz earth station antenna-noise temperature prediction program documentation for RAE-B

    Science.gov (United States)

    Chin, M.

    1972-01-01

    A simulation study to determine the 136 MHz and 400 MHz noise temperature of the ground network antennas which will track the RAE-B satellite during data transmission periods is described. Since the noise temperature of the antenna effectively sets the signal-to-noise ratio (SNR) of the received signal, a knowledge of SNR will be helpful in locating the optimum time windows for data transmission during low-noise periods. Antenna-noise temperatures at 136 MHz and 400 MHz will be predicted for selected earth-based ground stations which will support RAE-B. The antenna-noise temperature predictions will include the effects of galactic-brightness temperature, the sun, and the brightest radio stars. Predictions will cover the ten-month period from March 1, 1973 to December 31, 1973. The RAE-B mission will be expecially susceptible to SNR degradation during the two eclipses of the Sun occurring in this period.

  6. The 136 MHZ/400 MHz earth station antenna-noise temperature prediction program for RAE-B

    Science.gov (United States)

    Taylor, R. E.; Fee, J. J.; Chin, M.

    1972-01-01

    A simulation study was undertaken to determine the 136 MHz and 400 MHz noise temperature of the ground network antennas which will track the RAE-B satellite during data transmission periods. Since the noise temperature of the antenna effectively sets the signal-to-noise ratio of the received signal, a knowledge of SNR will be helpful in locating the optimum time windows for data transmission during low noise periods. Antenna noise temperatures will be predicted for selected earth-based ground stations which will support RAE-B. Telemetry data acquisition will be at 400 MHz; tracking support at 136 MHz will be provided by the Goddard Range and Range Rate (RARR) stations. The antenna-noise temperature predictions will include the effects of galactic-brightness temperature, the sun, and the brightest radio stars. Predictions will cover the ten-month period from March 1, 1973 to December 31, 1973.

  7. Sigma A recognition sites in the Bacillus subtilis genome

    DEFF Research Database (Denmark)

    Jarmer, Hanne Østergaard; Larsen, Thomas Schou; Krogh, Anders Stærmose

    2001-01-01

    A hidden Markov model of sigma (A) RNA polymerase cofactor recognition sites in Bacillus subtilis, containing either the common or the extended -10 motifs, has been constructed based on experimentally verified sigma (A) recognition sites. This work suggests that more information exists...... at the initiation site of transcription in both types of promoters than previously thought. When tested on the entire B. subtilis genome, the model predicts that approximately half of the sigma (A) recognition sites are of the extended type. Some of the response-regulator aspartate phosphatases were among...

  8. Sigma: Web Retrieval Interface for Nuclear Reaction Data

    International Nuclear Information System (INIS)

    Pritychenko, B.; Sonzogni, A.A.

    2008-01-01

    The authors present Sigma, a Web-rich application which provides user-friendly access in processing and plotting of the evaluated and experimental nuclear reaction data stored in the ENDF-6 and EXFOR formats. The main interface includes browsing using a periodic table and a directory tree, basic and advanced search capabilities, interactive plots of cross sections, angular distributions and spectra, comparisons between evaluated and experimental data, computations between different cross section sets. Interactive energy-angle, neutron cross section uncertainties plots and visualization of covariance matrices are under development. Sigma is publicly available at the National Nuclear Data Center website at www.nndc.bnl.gov/sigma

  9. 6 Sigma DFSS technique which is easy to use

    International Nuclear Information System (INIS)

    2002-01-01

    This book gives descriptions of 6 sigma DFSS technique. The contents of this book are storm of change, way of problem and solution, importance of customer satisfaction, quality improvement is key of customer satisfaction, quality improvement equals cost cutting, quality aim in perfect level, finding basic cause, data is life, standardization is fundamentals of all activity for improvement, chief, Chang's house, collection of data, setting goal to improve, experiment is the best way, importance of the last step, x control power of 6 sigma and Let's go six-sigma.

  10. Dissipative quantum dynamics and nonlinear sigma-model

    International Nuclear Information System (INIS)

    Tarasov, V.E.

    1992-01-01

    Sedov variational principle which is the generalization of the least action principle for the dissipative and irreversible processes and the classical dissipative mechanics in the phase space is considered. Quantum dynamics for the dissipative and irreversible processes is constructed. As an example of the dissipative quantum theory the nonlinear two-dimensional sigma-model is considered. The conformal anomaly of the energy momentum tensor trace for closed bosonic string on the affine-metric manifold is investigated. The two-loop metric beta-function for nonlinear dissipative sigma-model was calculated. The results are compared with the ultraviolet two-loop conterterms for affine-metric sigma model. 71 refs

  11. Detecting and Characterizing Exoplanets with the WFIRST Coronagraph: Colors of Planets in Standard and Designer Bandpasses-SETI

    Science.gov (United States)

    Turnbull, Margaret

    The WFIRST mission is now envisioned to include a coronagraph for the purpose of direct detection of nearby exoplanets, including planets known to exist via radial velocity detection and new discoveries. Assuming that starlight rejection sufficient for planet detection (~1e-9) can be achieved, what can be learned about these planets given a realistic spectral resolution and signal-to-noise ratio? We propose to investigate the potential for WFIRST to efficiently discriminate planets from background sources, and to characterize planets in terms of important diagnostic atmospheric features, using broad- and intermediate band color data. We will map out this capability as a function of signal-to-noise ratio, bandpass location, and bandpass width. Our investigation will place emphasis on gas giants, ice giants, and mini-Neptunes (compatible with current AFTA-C baseline performance specifications), as well as a variety of super-Earths (an AFTA-C "stretch" goal). We will explore a variety of compositions, cloud types, phase angles, and (in the case of super-Earths with semi-transparent atmospheres) surface types. Noiseless spectra generated for these model planets will be passed through (a) standard bandpasses for comparison to prior work and (b) filter transmission curves corresponding to bandpasses of 5-20% over the full range of WFIRST's expected bandpass (400 - 1,000 nm). From this, filter combinations will be used to generate planet colors and find filter sets that most efficiently discriminate between planets and background sources, and between planets of different type. We will then repeat this exercise for S/N levels of 1-1,000 in order to (1) explore the true efficacy of broadband measurements in exoplanet studies, and (2) provide an estimate of total required integration time for a compelling WFIRST exoplanet program. To accomplish this, we will use model spectra for mini-Neptunes, and ice and gas giants of varying composition (Hu et al. 2013), and observed

  12. The sigma model on complex projective superspaces

    Energy Technology Data Exchange (ETDEWEB)

    Candu, Constantin; Mitev, Vladimir; Schomerus, Volker [DESY, Hamburg (Germany). Theory Group; Quella, Thomas [Amsterdam Univ. (Netherlands). Inst. for Theoretical Physics; Saleur, Hubert [CEA Saclay, 91 - Gif-sur-Yvette (France). Inst. de Physique Theorique; USC, Los Angeles, CA (United States). Physics Dept.

    2009-08-15

    The sigma model on projective superspaces CP{sup S-1} {sup vertical} {sup stroke} {sup S} gives rise to a continuous family of interacting 2D conformal field theories which are parametrized by the curvature radius R and the theta angle {theta}. Our main goal is to determine the spectrum of the model, non-perturbatively as a function of both parameters. We succeed to do so for all open boundary conditions preserving the full global symmetry of the model. In string theory parlor, these correspond to volume filling branes that are equipped with a monopole line bundle and connection. The paper consists of two parts. In the first part, we approach the problem within the continuum formulation. Combining combinatorial arguments with perturbative studies and some simple free field calculations, we determine a closed formula for the partition function of the theory. This is then tested numerically in the second part. There we propose a spin chain regularization of the CP{sup S-1} {sup vertical} {sup stroke} {sup S} model with open boundary conditions and use it to determine the spectrum at the conformal fixed point. The numerical results are in remarkable agreement with the continuum analysis. (orig.)

  13. Sigma-1 receptor and inflammatory pain.

    Science.gov (United States)

    Gris, Georgia; Cobos, Enrique José; Zamanillo, Daniel; Portillo-Salido, Enrique

    2015-06-01

    The sigma-1 receptor (Sig-1R) is a unique ligand-regulated molecular chaperone that interacts with several protein targets such as G protein-coupled receptors and ion channels to modulate their activity. Sig-1R is located in areas of the central and peripheral nervous system that are key to pain control. Previous preclinical studies have suggested a potential therapeutic use of Sig-1R antagonists for the management of neuropathic pain. Recent studies using pharmacological and genetic tools have explored the role of Sig-1R in inflammatory pain conditions. Mice lacking the Sig-1R have shown different patterns of phenotypic responses to inflammatory injury. Systemic or peripheral administration of several Sig-1R antagonists, including the selective Sig-1R antagonist S1RA, inhibited both mechanical and thermal hypersensitivity in several preclinical models of inflammatory pain. These recent studies are summarized in the present commentary. Central and peripheral pharmacological blockade of Sig-1R could be an effective option to treat inflammatory pain.

  14. The sigma model on complex projective superspaces

    International Nuclear Information System (INIS)

    Candu, Constantin; Mitev, Vladimir; Schomerus, Volker; Quella, Thomas; Saleur, Hubert; USC, Los Angeles, CA

    2009-08-01

    The sigma model on projective superspaces CP S-1 vertical stroke S gives rise to a continuous family of interacting 2D conformal field theories which are parametrized by the curvature radius R and the theta angle θ. Our main goal is to determine the spectrum of the model, non-perturbatively as a function of both parameters. We succeed to do so for all open boundary conditions preserving the full global symmetry of the model. In string theory parlor, these correspond to volume filling branes that are equipped with a monopole line bundle and connection. The paper consists of two parts. In the first part, we approach the problem within the continuum formulation. Combining combinatorial arguments with perturbative studies and some simple free field calculations, we determine a closed formula for the partition function of the theory. This is then tested numerically in the second part. There we propose a spin chain regularization of the CP S-1 vertical stroke S model with open boundary conditions and use it to determine the spectrum at the conformal fixed point. The numerical results are in remarkable agreement with the continuum analysis. (orig.)

  15. Sigma Routing Metric for RPL Protocol

    Directory of Open Access Journals (Sweden)

    Paul Sanmartin

    2018-04-01

    Full Text Available This paper presents the adaptation of a specific metric for the RPL protocol in the objective function MRHOF. Among the functions standardized by IETF, we find OF0, which is based on the minimum hop count, as well as MRHOF, which is based on the Expected Transmission Count (ETX. However, when the network becomes denser or the number of nodes increases, both OF0 and MRHOF introduce long hops, which can generate a bottleneck that restricts the network. The adaptation is proposed to optimize both OFs through a new routing metric. To solve the above problem, the metrics of the minimum number of hops and the ETX are combined by designing a new routing metric called SIGMA-ETX, in which the best route is calculated using the standard deviation of ETX values between each node, as opposed to working with the ETX average along the route. This method ensures a better routing performance in dense sensor networks. The simulations are done through the Cooja simulator, based on the Contiki operating system. The simulations showed that the proposed optimization outperforms at a high margin in both OF0 and MRHOF, in terms of network latency, packet delivery ratio, lifetime, and power consumption.

  16. Establishing a Lean Six Sigma Program in Higher Education

    KAUST Repository

    Svensson, Carsten; Baessa, Mohamed A.; Bakhsh, Majed M.

    2013-01-01

    Purpose: The objective of this paper is a contribution to the body of Lean Six Sigma knowledge within the vertical of higher education institutions. The paper will review the initial phase of an implementation and highlight future challenges. Approach: The observations presented in this paper, originates from rolling out a large lean six sigma implementation at a newly established university. The paper is supported with secondary data from literature. Findings: The paper will discuss the challenges of applying the lean six sigma method in a complex transactional environment. Research limitations: This paper is based on an empirical study of a single instance and authors’ experiences as practitioners. Originality: This paper is the first description of what is believed to be one of the largest implementations of Lean Six Sigma in higher education.

  17. Sphaleron in a non-linear sigma model

    International Nuclear Information System (INIS)

    Sogo, Kiyoshi; Fujimoto, Yasushi.

    1989-08-01

    We present an exact classical saddle point solution in a non-linear sigma model. It has a topological charge 1/2 and mediates the vacuum transition. The quantum fluctuations and the transition rate are also examined. (author)

  18. On D-branes from gauged linear sigma models

    International Nuclear Information System (INIS)

    Govindarajan, S.; Jayaraman, T.; Sarkar, T.

    2001-01-01

    We study both A-type and B-type D-branes in the gauged linear sigma model by considering worldsheets with boundary. The boundary conditions on the matter and vector multiplet fields are first considered in the large-volume phase/non-linear sigma model limit of the corresponding Calabi-Yau manifold, where we find that we need to add a contact term on the boundary. These considerations enable to us to derive the boundary conditions in the full gauged linear sigma model, including the addition of the appropriate boundary contact terms, such that these boundary conditions have the correct non-linear sigma model limit. Most of the analysis is for the case of Calabi-Yau manifolds with one Kaehler modulus (including those corresponding to hypersurfaces in weighted projective space), though we comment on possible generalisations

  19. Quality and Competitiveness: A Lean Six Sigma Approach

    Directory of Open Access Journals (Sweden)

    Irina-Virginia Drăgulănescu

    2015-11-01

    Full Text Available Originally developed to improve the quality and production efficiency, Lean Six Sigma is now widely adopted in other non-manufacturing sectors such as financial, trade, services, etc. The methodology known as Lean Six Sigma combines the Six Sigma techniques, ‒ which allow companies to reduce manufacturing defects ‒ and the Lean Manufacturing principles, ‒ which help companies benefit from faster processing for lower costs and with superior quality. As a result of the research, the authors observed that, despite growing popularity and impressive outcomes obtained by some companies, the Lean Six Sigma model does not always offer the expected results. However, the research has shown that the analysed company, operating in the field of courier services has managed to boost productivity and competitiveness by implementing measures that generated added value.

  20. The Role of Sigma Receptor in Breast Cancer

    National Research Council Canada - National Science Library

    Pusztai, Lajos

    2004-01-01

    We have completed specific tasks #1 and #2. Sigma 1 receptor (Sig 1 R) mRNA expression was examined in 109 human tissue specimens including normal breast, hyperplasia, ductal carcinoma in situ, and invasive cancer...

  1. Establishing a Lean Six Sigma Program in Higher Education

    KAUST Repository

    Svensson, Carsten

    2013-09-12

    Purpose: The objective of this paper is a contribution to the body of Lean Six Sigma knowledge within the vertical of higher education institutions. The paper will review the initial phase of an implementation and highlight future challenges. Approach: The observations presented in this paper, originates from rolling out a large lean six sigma implementation at a newly established university. The paper is supported with secondary data from literature. Findings: The paper will discuss the challenges of applying the lean six sigma method in a complex transactional environment. Research limitations: This paper is based on an empirical study of a single instance and authors’ experiences as practitioners. Originality: This paper is the first description of what is believed to be one of the largest implementations of Lean Six Sigma in higher education.

  2. In search of Six Sigma in Portuguese SMEs

    OpenAIRE

    Fonseca, Luis Miguel

    2017-01-01

    This exploratory research aims to study the reasons for the low implementation level of Six Sigma within Portuguese Small and Medium Enterprises. The results suggest that ISO 9001 certification, and Lean Management, are still regarded as enough for company success. The descriptive analysis and the statistical tests performed led to the conclusion that there are no significant differences for the motivations not to implement Six Sigma between small and medium companies. The qualitative researc...

  3. Improving laboratory data entry quality using Six Sigma.

    Science.gov (United States)

    Elbireer, Ali; Le Chasseur, Julie; Jackson, Brooks

    2013-01-01

    The Uganda Makerere University provides clinical laboratory support to over 70 clients in Uganda. With increased volume, manual data entry errors have steadily increased, prompting laboratory managers to employ the Six Sigma method to evaluate and reduce their problems. The purpose of this paper is to describe how laboratory data entry quality was improved by using Six Sigma. The Six Sigma Quality Improvement (QI) project team followed a sequence of steps, starting with defining project goals, measuring data entry errors to assess current performance, analyzing data and determining data-entry error root causes. Finally the team implemented changes and control measures to address the root causes and to maintain improvements. Establishing the Six Sigma project required considerable resources and maintaining the gains requires additional personnel time and dedicated resources. After initiating the Six Sigma project, there was a 60.5 percent reduction in data entry errors from 423 errors a month (i.e. 4.34 Six Sigma) in the first month, down to an average 166 errors/month (i.e. 4.65 Six Sigma) over 12 months. The team estimated the average cost of identifying and fixing a data entry error to be $16.25 per error. Thus, reducing errors by an average of 257 errors per month over one year has saved the laboratory an estimated $50,115 a year. The Six Sigma QI project provides a replicable framework for Ugandan laboratory staff and other resource-limited organizations to promote quality environment. Laboratory staff can deliver excellent care at a lower cost, by applying QI principles. This innovative QI method of reducing data entry errors in medical laboratories may improve the clinical workflow processes and make cost savings across the health care continuum.

  4. Four dimensional sigma model coupled to the metric tensor field

    International Nuclear Information System (INIS)

    Ghika, G.; Visinescu, M.

    1980-02-01

    We discuss the four dimensional nonlinear sigma model with an internal O(n) invariance coupled to the metric tensor field satisfying Einstein equations. We derive a bound on the coupling constant between the sigma field and the metric tensor using the theory of harmonic maps. A special attention is paid to Einstein spaces and some new explicit solutions of the model are constructed. (author)

  5. Six sigma critical success factors in manufacturing industries

    Science.gov (United States)

    Mustafa, Zainol; Jamaluddin, Z.

    2017-04-01

    The success of Six Sigma implementation is known to depend on a number of contributing factors. The purpose of this paper is to explore Six Sigma critical success factors (CSFs) in the context of Malaysian manufacturing organizations. Although Six Sigma success factors have been abundantly researched in the global context, in this paper, a maiden attempt is made to identify, through an extensive literature review, the CSFs for Six Sigma implementation followed by their validation using primary data collection from Malaysian manufacturing companies. A total of 33 indicators have thus been compiled through an extensive literature review which then been grouped into 6 contributing factors. These contributing success factors are then validated through an empirical research of selected Malaysian manufacturing companies at various stages of implementation of the Six Sigma process improvement methodology. There has been an overemphasis on the role and commitment of the management in the success of a Six Sigma program. Though it is undoubted, certain other factors also play an equally important role in ensuring that the Six Sigma programs are successful. The factor analysis of CSFs of the Malaysian manufacturing organizations selected in this study demonstrates that the top factor is a composite factor showing combination of the ability of the project teams to use the process management on quality initiative and a training using a proper analysis in problem solving. The CSFs extracted through the factor analysis could provide a basis for manufacturing organizations embarking on the Six Sigma journey to look beyond just management involvement. Thus, one can develop an integrated framework of other factors as outlined and give them appropriate priority and focus.

  6. Kinetics of sigma phase formation in a Duplex Stainless Steel

    Directory of Open Access Journals (Sweden)

    Rodrigo Magnabosco

    2009-09-01

    Full Text Available This work determines the kinetics of sigma phase formation in UNS S31803 Duplex Stainless Steel (DSS, describing the phase transformations that occur in isothermal aging between 700 and 900 ºC for time periods up to 1032 hours, allowing the determination of the Time-Temperature-Precipitation (TTP diagram for sigma phase and proposing a model to predict the kinetics of sigma phase formation using a Johnson-Mehl-Avrami (JMA type expression. The higher kinetics of sigma phase formation occurs at 850 ºC. However, isothermal aging between 700 and 900 ºC for time periods up to 1032 hours are not sufficient to the establishment of thermodynamic equilibrium. Activation energy for both nucleation and growth of sigma phase is determined (185 kJ.mol-1 and its value is equivalent to the activation energy for Cr diffusion in ferrite, indicating that diffusion of Cr is probably the major thermally activated process involved in sigma phase formation. The determined JMA type expression presents good fit with experimental data between 700 and 850 ºC.

  7. Success of manufacturing industries – Role of Six Sigma

    Directory of Open Access Journals (Sweden)

    Venkatesh N.

    2018-01-01

    Full Text Available Six Sigma is a phenomenal quality management concepts which has helped many organizations to overcome quality crisis in the recent past. Six Sigma is observed as a very promising quality management tool for any organization to make its presence felt in the corporate world as it emphasizes on obtaining a fruitful solution to improve accuracy, reduce defect thereby reduce the cost and improve profits. The main objective of this investigation is to unearth the extent to which the companies have been benefitted due to Six Sigma implementation. This article presents the results based on the analysis of collective opinion of employees of various Indian manufacturing industries that have implemented Six Sigma. This research also examines interrelationship among various parameters defined in the research. The research revealed that industries are benefitted irrespective of their nature in terms of their growth, financial benefits, productivity and satisfaction of the customer. However, peoples’ equity that deals with the benefits that employees obtain after Six Sigma implementation is not certain. The research also revealed the existence of strong interrelationship among various parameters used to measure the success of Six Sigma.

  8. Lean sigma--will it work for healthcare?

    Science.gov (United States)

    Bahensky, James A; Roe, Janet; Bolton, Romy

    2005-01-01

    The manufacturing industry has been using Lean Sigma for years in pursuit of continuous improvement to obtain a competitive advantage. The objectives of these efforts are to use the Lean techniques for reducing cycle times and the Six Sigma concepts for reducing product defects. The Iowa Business Council with several advocates worked with the University of Iowa Hospital and Clinics (UIHC) and two other Iowa hospitals to determine whether Lean Sigma is adaptable in healthcare. A team of 15 people at UIHC used the Kaizen Breakthrough Methodology over a five-day period in an aggressive identification and elimination of non-value added activities in Radiology CT scanning. The results exceeded the initial project objectives and indicated that Lean Sigma is applicable in healthcare. Overall, the Lean Sigma project increased revenue by approximately $750,000 per year. The Kaizen process proved to be successful and interesting. Within three days, the team installed new work flow processes. This implementation-oriented approach is what differentiates Lean Sigma from other quality improvement processes.

  9. Six Sigma Project Selection Using Fuzzy TOPSIS Decision Making Approach

    Directory of Open Access Journals (Sweden)

    Rajeev Rathi

    2015-05-01

    Full Text Available Six Sigma is considered as a logical business strategy that attempts to identify and eliminate the defects or failures for improving the quality of product and processes. A decision on project selection in Six Sigma is always very critical; it plays a key role in successful implementation of Six Sigma. Selection of a right Six Sigma project is essentially important for an automotive company because it greatly influences the manufacturing costs. This paper discusses an approach for right Six Sigma project selection at an automotive industry using fuzzy logic based TOPSIS method. The fuzzy TOPSIS is a well recognized tool to undertake the fuzziness of the data involved in choosing the right preferences. In this context, evaluation criteria have been designed for selection of best alternative. The weights of evaluation criteria are calculated by using the MDL (modified digital logic method and final ranking is calculated through priority index obtained by using fuzzy TOPSIS method. In the selected case study, this approach has rightly helped to identify the right project for implementing Six Sigma for achieving improvement in productivity.

  10. Discovery of a 7 mHz X-Ray Quasi-Periodic Oscillation from the Most Massive Stellar-Mass Black Hole IC 10 X-1

    Science.gov (United States)

    Pasham, Dheeraj R.; Strohmayer, Tod E.; Mushotzky, Richard F.

    2013-01-01

    We report the discovery with XMM-Newton of an approx.. = 7 mHz X-ray (0.3-10.0 keV) quasi-periodic oscillation (QPO) from the eclipsing, high-inclination black hole binary IC 10 X-1. The QPO is significant at >4.33 sigma confidence level and has a fractional amplitude (% rms) and a quality factor, Q is identical with nu/delta nu, of approx. = 11 and 4, respectively. The overall X-ray (0.3-10.0 keV) power spectrum in the frequency range 0.0001-0.1 Hz can be described by a power-law with an index of approx. = -2, and a QPO at 7 mHz. At frequencies approx. > 0.02 Hz there is no evidence for significant variability. The fractional amplitude (rms) of the QPO is roughly energy-independent in the energy range of 0.3-1.5 keV. Above 1.5 keV the low signal-to-noise ratio of the data does not allow us to detect the QPO. By directly comparing these properties with the wide range of QPOs currently known from accreting black hole and neutron stars, we suggest that the 7 mHz QPO of IC 10 X-1 may be linked to one of the following three categories of QPOs: (1) the "heartbeat" mHz QPOs of the black hole sources GRS 1915+105 and IGR J17091-3624, or (2) the 0.6-2.4 Hz "dipper QPOs" of high-inclination neutron star systems, or (3) the mHz QPOs of Cygnus X-3.

  11. Development of disposable membrane hydrophones for a frequency range from 1MHz to 10MHz.

    Science.gov (United States)

    Lee, Jae-Wan; Ohm, Won-Suk; Kim, Yong-Tae

    2017-11-01

    A method for fabricating disposable membrane hydrophones is presented. The disposable hydrophones are intended for onetime use in such damaging environments as chemically contaminating fluids and high-amplitude (peak amplitude ∼100MPa) shock wave fields, where the use of commercial membrane hydrophones is not recommended. Fabrication of a hydrophone is done using only off-the-shelf components and hand tools, which translates into ease of fabrication and orders-of-magnitude reduction in unit cost. In particular, poling and sputtering, the two processes that are chiefly responsible for the cost and difficulty associated with the conventional fabrication method, are replaced with the use of pre-poled polyvinylidene fluoride (PVDF) films and polyethylene terephthalate (PET)-coated aluminum foils, respectively. Despite the seemingly crude construction, these disposable hydrophones can exhibit voltage sensitivity response that compares favorably with that of commercial hydrophones. For example, one prototype having a 2mm×2mm active element shows the end-of-cable voltage sensitivity of -270 (±1.9) dB re 1V/μPa over the frequency range of 1-10MHz. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. 120 MW, 800 MHz Magnicon for a Future Muon Collider

    International Nuclear Information System (INIS)

    Jay L. Hirshfield

    2005-01-01

    Development of a pulsed magnicon at 800 MHz was carried out for the muon collider application, based on experience with similar amplifiers in the frequency range between 915 MHz and 34.3 GHz. Numerical simulations using proven computer codes were employed for the conceptual design, while established design technologies were incorporated into the engineering design. A cohesive design for the 800 MHz magnicon amplifier was carried out, including design of a 200 MW diode electron gun, design of the magnet system, optimization of beam dynamics including space charge effects in the transient and steady-state regimes, design of the drive, gain, and output cavities including an rf choke in the beam exit aperture, analysis of parasitic oscillations and design means to eliminate them, and design of the beam collector capable of 20 kW average power operation

  13. POLARIMETRIC OBSERVATIONS OF {sigma} ORIONIS E

    Energy Technology Data Exchange (ETDEWEB)

    Carciofi, A. C.; Faes, D. M. [Instituto de Astronomia, Geofisica e Ciencias Atmosfericas, Universidade de Sao Paulo, Rua do Matao 1226, Cidade Universitaria, 05508-900 Sao Paulo, SP (Brazil); Townsend, R. H. D. [Department of Astronomy, University of Wisconsin-Madison, Sterling Hall, 475 N. Charter Street, Madison, WI 53706 (United States); Bjorkman, J. E., E-mail: carciofi@usp.br [Ritter Observatory, Department of Physics and Astronomy, University of Toledo, Toledo, OH 43606 (United States)

    2013-03-20

    Some massive stars possess strong magnetic fields that confine plasma in the circumstellar environment. These magnetospheres have been studied spectroscopically, photometrically, and, more recently, interferometrically. Here we report on the first firm detection of a magnetosphere in continuum linear polarization, as a result of monitoring {sigma} Ori E at the Pico dos Dias Observatory. The non-zero intrinsic polarization indicates an asymmetric structure whose minor elongation axis is oriented 150. Degree-Sign 0 east of the celestial north. A modulation of the polarization was observed with a period of half of the rotation period, which supports the theoretical prediction of the presence of two diametrally opposed, corotating blobs of gas. A phase lag of -0.085 was detected between the polarization minimum and the primary minimum of the light curve, suggestive of a complex shape of the plasma clouds. We present a preliminary analysis of the data with the Rigidly Rotating Magnetosphere model, which could not reproduce simultaneously the photometric and polarimetric data. A toy model comprising two spherical corotating blobs joined by a thin disk proved more successful in reproducing the polarization modulation. With this model we were able to determine that the total scattering mass of the thin disk is similar to the mass of the blobs (2M{sub b}/M{sub d} = 1.2) and that the blobs are rotating counterclockwise on the plane of the sky. This result shows that polarimetry can provide a diagnostic of the geometry of clouds, which will serve as an important constraint for improving the Rigidly Rotating Magnetosphere model.

  14. 47 CFR 90.353 - LMS operations in the 902-928 MHz band.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false LMS operations in the 902-928 MHz band. 90.353... operations in the 902-928 MHz band. LMS systems may be authorized within the 902-928 MHz band, subject to the..., scientific, and medical (ISM) devices and radiolocation Government stations that operate in the 902-928 MHz...

  15. 78 FR 42701 - Improving Public Safety Communications in the 800 MHz Band

    Science.gov (United States)

    2013-07-17

    ...] Improving Public Safety Communications in the 800 MHz Band AGENCY: Federal Communications Commission. ACTION...-901 MHz/935- 940 MHz band (900 MHz B/ILT Band) to allow a qualified entity to file an application for..., manufacturing, energy) to non-commercial (e.g., clerical, educational, philanthropic, medical). In 2004, the...

  16. 77 FR 22720 - Service Rules for Advanced Wireless Services in the 2000-2020 MHz and 2180-2200 MHz Bands, etc.

    Science.gov (United States)

    2012-04-17

    ... operations in 1930-1995 MHz and uplink operations in 2000-2020 MHz. To address this apparent tension, we seek... includes broadcast auxiliary service (BAS) and cable television service (CARS) operations, as well as...

  17. Peningkatan performansi produksi dengan pendekatan lean six sigma

    Directory of Open Access Journals (Sweden)

    H. Harisupriyanto

    2018-01-01

    Full Text Available Abstrak Persaingan pasar tidak sekedar menjual produk akan tetapi membutuhkan kualitas produk yang semakin baik. Kondisi tersebut semakin penting bila dihubungkan dengan permintaan produk yang semakin tinggi. Untuk itu diperlukan pengolahan sumber daya yang semakin efisiensi dan effektif. Sering terjadi proses produksi berhenti dan ditaksir kerugian finansial yang tinggi. Terdapat aktifitas yang bersifat non value added. Aktifitas tersebut menyebabkan timbulnyalosses. Diperlukan cara untuk menelusuri penyebab terjadinya waste atau losses pada aktivitas produksi dengan pendekatan lean six sigma. Tools yang dipakai untuk mengidentifikasi permasalahan adalah E-DOWNTIME waste, RCA (root cause Analisys dan FMEA (Failure modes and effect analysis. Diperoleh hasil bahwavalue added activity sebesar 22%, necessary but non value added activity yaitu 44% dan nonvalue added activity sebesar 34%. Diperoleh tiga waste kritis yaitu waiting, defect dan excess processing waste. Nilai sigma awal pada defect waste yaitu sebesar 2.70;nilai sigma ini merupakan permasalahan. Rekomendasi perbaikan adalah pembuatan dan pengawasan SOP dan pengadaan pelatihan guna meningkatkan kemampuan dan keterampilan tenaga kerja. Terjadi kenaikan nilai sigma sampai 3.10 dan terjadi pengurangan biaya sampai 25%. Kata Kunci: Losses, activity, RCA, Lean, six-sigma Abstract The market competition is not just selling a product but needs a better product quality. That condition increasingly important when associated with higher product demand. It required the processing resources more efficient and effective.The production process often stops and estimated financial loss is high. There were indications of activities nonvalue added. These activities cause losses. Need a way to explore the causes of waste or losses in production activities with lean six- sigma approach.Tools used to identify the problem are E-DOWNTIME waste, RCA (root cause Analisys and FMEA (Failure modes and effects

  18. Cambridge observations at 38-115 MHz and their implications for space astronomy

    International Nuclear Information System (INIS)

    Saunders, R.

    1987-01-01

    The design and performance of the Cambridge LF telescopes are reviewed. Consideration is given to the 151-MHz 6C telescope, the 38-MHz and 151-MHz LF synthesis telescopes, 81.5-MHz interplanetary scintillation observations with the 3.6-hectare array, long-baseline interferometry at 81.5 MHz, and the use of the Jodrell Bank MERLIN for 151-MHz closure-phase observations of bright sources. The strict limitation on the field mappable at a given resolution in ground-based observations at these frequencies is pointed out, and some outstanding astronomical problems requiring 0.3-30-MHz space observations are listed. 7 references

  19. Performance of the inverse photoemission spectrometer with a new bandpass photon detector of narrow bandwidth and high sensitivity

    International Nuclear Information System (INIS)

    Ueda, Yoshifumi; Nishihara, Katsuhiro; Mimura, Kojiro; Hari, Yasuko; Taniguchi, Masaki; Fujisawa, Masami

    1993-01-01

    A combination of a SrF 2 entrance window and a photomultiplier with the Cu-BeO first dynode coated with KCl film realizes the bandpass photon detector with the FWHM of 0.47 eV centered at 9.43 eV and the sensitivity improved by about one order of magnitude in comparison with the detector without the KCl film. The overall energy resolution of the inverse photoemission spectrometer consisting of an electron gun with a BaO cathode and the new detector has been estimated to be 0.56 eV using polycrystalline Au. Typical counting rate is 10 2 -10 3 counts/(μA s) for unoccupied states near the Fermi level of the Au at an acceptance angle of about 0.8π sr with an Al collecting mirror. (orig.)

  20. 3D lumped components and miniaturized bandpass filter in an ultra-thin M-LCP for SOP applications

    KAUST Repository

    Arabi, Eyad A.

    2013-01-01

    In this work, a library of 3D lumped components completely embedded in the thinnest, multilayer LCP (M-LCP) stack- up with four metallization layers and 100 μm of total thickness, is reported for the first time. A vertically and horizontally interdigitated capacitor, realized in this stack-up, provides higher self resonant frequency as compared to a similarly sized conventional parallel plate capacitor. Based on the above mentioned library, a miniaturized bandpass filter is presented for the GPS application. It utilizes mutually coupled inductors and is the smallest reported in the literature with a size of (0.035×0.028×0.00089)λg. Finally, the same filter realized in a competing ceramic technology (LTCC) is compared in performance with the ultra-thin M-LCP design. The M-LCP module presented in this work is inherently exible and offers great potential for wearable and conformal applications.

  1. 47 CFR 90.672 - Unacceptable interference to non-cellular 800 MHz licensees from 800 MHz cellular systems or part...

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Unacceptable interference to non-cellular 800 MHz licensees from 800 MHz cellular systems or part 22 Cellular Radiotelephone systems, and within the... Procedures and Process-Unacceptable Interference § 90.672 Unacceptable interference to non-cellular 800 MHz...

  2. Acceleration performance of a 50-MHz split coaxial RFQ and the design of a 25.5-MHz prototype

    International Nuclear Information System (INIS)

    Tokuda, N.; Arai, S.; Fukushima, T.; Morimoto, T.; Tojyo, E.

    1989-03-01

    Acceleration tests on a 50-MHz split coaxial RFQ have been conducted at INS. The 2-m long RFQ has accelerated protons from 2 to 60 keV. The experimental results concerning beam emittance and transmission efficiency agree with predictions of a computer simulation. Following this success, we are fabricating a 25.5-MHz prototype of 2-m long. The issues of the study are to establish a structure standing a high-power operation and to accelerate heavy ions with a charge-to-mass ratio larger than 1/30. (author)

  3. 17 bit 4.35 mW 1 kHz Delta Sigma ADC and 256-to-1 multiplexer for remote handling instrumentation equipment

    Energy Technology Data Exchange (ETDEWEB)

    Verbeeck, Jens, E-mail: jens.verbeeck@esat.kuleuven.be [KU Leuven, Department ESAT-MICAS, Kasteelpark Arenberg 10, 3001 Heverlee (Belgium); KH Kempen University College, IBW-RELIC, Kleinhoefstraat 4, 2440 Geel (Belgium); Van Uffelen, Marco [Fusion for Energy, c/Josep, n° 2, Torres Diagonal Litoral, Ed. B3, 08019 Barcelona (Spain); Steyaert, Michiel [KU Leuven, Department ESAT-MICAS, Kasteelpark Arenberg 10, 3001 Heverlee (Belgium); Leroux, Paul [KU Leuven, Department ESAT-MICAS, Kasteelpark Arenberg 10, 3001 Heverlee (Belgium); KH Kempen University College, IBW-RELIC, Kleinhoefstraat 4, 2440 Geel (Belgium)

    2013-10-15

    Highlights: ► We present a radiation hard 17 bit-1 kHz 4.35 mW Delta Sigma ADC. ► A radiation tolerant 256-to-1 multiplexer is shown. ► We propose a generic radiation tolerant ASIC for use in an instrumentation link. ► The ASIC can interface more than hundred pressure or resistive sensors. ► All building blocks have a simulated radiation tolerance of more than 1 MGy. -- Abstract: A radiation tolerant Delta-Sigma Analog-to-Digital Converter (ADC) and multiplexer is presented. The design features a 1.5 V, 17 bit ADC consuming 4.35 mW at a sample frequency of 1 MHz. The ADC features a bandwidth of 1 kHz and utilizes a Correlated Double Sampling technique (CDS) to remove offset and 1/f noise. The circuit maintains its 17 bit resolution upon a simulated radiation dose exceeding 1 MGy and varying temperatures between 0 °C and 85 °C. Next a multiplexer is presented. It can multiplex 256 channels at a clock frequency of 128 MHz or has a data throughput of 256 MSample/s. In addition the bit period of the multiplexer varies less then 1.5% due to the influence of temperature or radiation, which proves the temperature and radiation tolerance.

  4. MEMS Tunable Antennas to Address LTE 600 MHz-bands

    DEFF Research Database (Denmark)

    Barrio, Samantha Caporal Del; Morris, Art; Pedersen, Gert Frølund

    2015-01-01

    The broadcast television spectrum around 600 MHz has been freed in the united states and will be put for auction to wireless carriers in 2015. The newest generation of mobile communication standards will be deployed on these newly available bands, to provide mobile device users with an enhanced c...

  5. Charge domain filter operating up to 20 MHz clock frequency

    NARCIS (Netherlands)

    Gal, R.A.J.; Wallinga, Hans

    1983-01-01

    An analog sampled data low pass third order Butterworth filter has been realised in a buried channel CCD technology. This Charge Domain Filter, composed of transversal and recursive CCD filter sections, has been tested at clock frequencies up to 20 MHz.

  6. Calibration of SAR probes in waveguide at 900 MHz

    International Nuclear Information System (INIS)

    Jokela, K.; Puranen, L.; Hyysalo, P.

    1998-01-01

    The radiation safety tests for hand-held mobile phones require precise calibration of the small electric field probes used for the measurement of SAR in phantoms simulating the human body. In this study a calibration based on a rectangular waveguide was developed for SAR calibrations at 900 MHz

  7. 500 MHz transient digitizers based on GaAs CCDs

    International Nuclear Information System (INIS)

    Bryman, D.; Cresswell, J.V.; LeNoble, M.; Poutissou, R.

    1990-10-01

    A wide bandwidth transient digitizer based on a recently produced gallium arsenide charged coupled device is under development. The CCDs have 128 pixels and operate at 500 MHz. Initial testing of prototype modules in Experiment 787 at Brookhaven National Laboratory is reported. (Author) (8 refs., 10 figs.)

  8. MIMOSA. A 32 channel 40 MHz Camac scaler

    International Nuclear Information System (INIS)

    Beer, A.; Bourgeois, F.; Critin, G.

    1981-01-01

    This report describes a 32 channel, 24 bit, 40 MHz single width Camac scaler based on the memory increment technique. The characteristics of the module are given and its logic is briefly described. Circuit diagrams and component lists are given. (orig.)

  9. Status of 174 MHz RF system for BEP

    International Nuclear Information System (INIS)

    Biryuchevsky, Yu.A.; Gorniker, E.I.; Kendjebulatov, E.K.; Krutikhin, S.A.; Kurkin, G.Ya.; Petrov, V.M.; Pilan, A.M.

    2012-01-01

    The new RF system for the BEP storage ring (which is an injector of VEPP-2000 accelerating complex) will increase the particles energy in the BEP from 0.9 to 1 GeV. RF system operates at a frequency of 174 MHz and consists of an accelerating cavity, RF power generator and control system.

  10. Sistem Informasi Kinerja Layanan Laboratorium Medis dengan Metode Six Sigma

    Directory of Open Access Journals (Sweden)

    Anindita Kusumastuti Dewi

    2016-01-01

    Full Text Available Medical Laboratory currently holds a very important role in medicine. Evaluation of laboratory quality plays a very important to maintain accurate laboratory results. This study aims to design an information system performance based on the same perception of medical laboratory services from customers using Six Sigma methods and frameworks using ServQual questionnaire. Selection of Six Sigma itself is based on this method can measure the extent to which each process deviates from its purpose as well as to reduce the variation of each of the attributes.  Six Sigma DMAIC namely (Define, Measure, Analyze, Improve, Control preferred because the end result will not yield new products, but only improvements on existing processes. The results of this calculation will be presented in the form of a dashboard for easier management in understanding the results of the evaluation. From the system can be obtained an average value of consumer perceptions terhdap performance today is 2,883, consumer expectations on the performance of 3.3768, the gap between the perceptions and expectations of consumers is -0.4936, customer satisfaction will be the performance of the current 85.37%, the value of 423 360 DPMO and sigma value there at the 2.07664 level.   Keywords: Laboratory Performance; Six Sigma; Servqual; Dashboard

  11. A Lean Six Sigma program in higher education

    KAUST Repository

    Svensson, Carsten

    2015-01-01

    Purpose The objective of this paper is to contribute to the body of Lean Six Sigma knowledge within the field of higher education institutions. The paper will review the initial phase of an implementation and highlight future challenges of applying the Lean Six Sigma method in a complex transactional environment. Design/methodology/approach The observations presented in this paper originate from rolling out a large Lean Six Sigma implementation at a recently established university. The paper is supported with secondary data from literature. Findings The implementation of Lean Six Sigma methodology at King Abdullah University of Science and Technology (KAUST) has resulted in improvements in business processes and efficiency. This has been achieved through project execution and training programs. Approximately 350 staff members have completed awareness training, 50 yellow belts and 150 green belts have been trained, and the first round of seven black belts have completed training of which two have completed certification. Research limitations/implications This paper is based on an empirical study of a single instance and the authors’ experiences as practitioners. Originality/value This paper is the first description of what is believed to be one of the largest implementations of Lean Six Sigma in higher education.

  12. APLIKASI SIX SIGMA PADA PRODUK CLEAR FILE DI PERUSAHAAN STATIONARY

    Directory of Open Access Journals (Sweden)

    Desy Emilasari

    2007-01-01

    Full Text Available This paper describes the application of the Six Sigma methods is used in order to improve quality in manufacturing company that produce stationary product. DMAIC approach is utilized to analyze and improve 'Pocket Clear File' product since this product has more variability and defects. Quality improvement also monitor the process that influenced pocket defect in Bag Making, Kami-ire, Karidome, and Pocket after Karidome Inspections section. Determining of Six Sigma project is based in process and defect type in each section. FMEA also gave the recommendation for quality improvement we need to evaluate the final result of the improvement since some of them were not working properly. Abstract in Bahasa Indonesia : Paper ini menggambarkan bagaimana aplikasi metode Six Sigma digunakan untuk melakukan perbaikan kualitas pada perusahaan manufaktur yang memproduksi produk stationary. Pendekatan DMAIC dipakai untuk menganalisa dan melakukan perbaikan produk 'Pocket Clear File' karena tingginya variabilitas dan cacat dibanding produk lain. Perbaikan kualitas juga memperhatikan proses yang mempengaruhi terjadinya cacat pocket pada section Bag Making, Kami-ire, Karidome, dan Pocket after Karidome Inspection. Penentuan proyek Six Sigma didasarkan atas proses dan jenis cacat pada setiap section. Pendekatan FMEA mampu memberi rekomendasi perbaikan kualitas. Evaluasi dari hasil perbaikan penting untuk dilakukan karena beberapa implementasi perbaikan kualitas tidak berjalan sesuai dengan rencana. kata kunci: six sigma, DMAIC, perusahaan stationary.

  13. Can Six Sigma be the "cure" for our "ailing" NHS?

    Science.gov (United States)

    Antony, Jiju; Downey-Ennis, Kay; Antony, Frenie; Seow, Chris

    2007-01-01

    The purpose of this research is to analyse whether Six Sigma business strategy can be used to improve the financial and operational performance of the NHS. The paper will also look at some of the major challenges and barriers in the implementation of this powerful process improvement strategy within the healthcare sector. This paper discusses whether Six Sigma DMAIC methodology can be a useful and disciplined approach to tackle process- and quality-related problems in the NHS. The paper presents some key findings from other researchers in the field, followed by some comments on whether Six Sigma is a useful approach to be considered by the NHS for cost reduction and defect reduction strategies. The paper illustrates the point that Six Sigma is not confined just to manufacturing industry, rather it is equally applicable to service industry, especially the healthcare and financial sectors. The application of Six Sigma in the UK health sector is relatively new and the purpose of the paper is to increase the awareness of this powerful business strategy in healthcare discipline.

  14. sigma model approach to the heterotic string theory

    International Nuclear Information System (INIS)

    Sen, A.

    1985-09-01

    Relation between the equations of motion for the massless fields in the heterotic string theory, and the conformal invariance of the sigma model describing the propagation of the heterotic string in arbitrary background massless fields is discussed. It is emphasized that this sigma model contains complete information about the string theory. Finally, we discuss the extension of the Hull-Witten proof of local gauge and Lorentz invariance of the sigma-model to higher order in α', and the modification of the transformation laws of the antisymmetric tensor field under these symmetries. Presence of anomaly in the naive N = 1/2 supersymmetry transformation is also pointed out in this context. 12 refs

  15. Analysis of CPN-1 sigma models via projective structures

    International Nuclear Information System (INIS)

    Post, S; Grundland, A M

    2012-01-01

    This paper represents a study of projector solutions to the Euclidean CP N-1 sigma model in two dimensions and their associated surfaces immersed in the su(N) Lie algebra. Any solution for the CP N-1 sigma model defined on the extended complex plane with finite action can be written as a raising operator acting on a holomorphic one. Here the proof is formulated in terms rank-1 projectors so it is explicitly gauge invariant. We apply these results to the analysis of surfaces associated with the CP N-1 models defined using the generalized Weierstrass formula for immersion. We show that the surfaces are conformally parametrized by the Lagrangian density, with finite area equal to the action of the model, and express several other geometrical characteristics of the surface in terms of the physical quantities of the model. Finally, we provide necessary and sufficient conditions that a surface be related to a CP N-1 sigma model

  16. Vortices, semi-local vortices in gauged linear sigma model

    International Nuclear Information System (INIS)

    Kim, Namkwon

    1998-11-01

    We consider the static (2+1)D gauged linear sigma model. By analyzing the governing system of partial differential equations, we investigate various aspects of the model. We show the existence of energy finite vortices under a partially broken symmetry on R 2 with the necessary condition suggested by Y. Yang. We also introduce generalized semi-local vortices and show the existence of energy finite semi-local vortices under a certain condition. The vacuum manifold for the semi-local vortices turns out to be graded. Besides, with a special choice of a representation, we show that the O(3) sigma model of which target space is nonlinear is a singular limit of the gauged linear sigma model of which target space is linear. (author)

  17. Quasicomplex N=2, d=1 Supersymmetric Sigma Models

    Directory of Open Access Journals (Sweden)

    Evgeny A. Ivanov

    2013-11-01

    Full Text Available We derive and discuss a new type of N=2 supersymmetric quantum mechanical sigma models which appear when the superfield action of the (1,2,1 multiplets is modified by adding an imaginary antisymmetric tensor to the target space metric, thus completing the latter to a non-symmetric Hermitian metric. These models are not equivalent to the standard de Rham sigma models, but are related to them through a certain special similarity transformation of the supercharges. On the other hand, they can be obtained by a Hamiltonian reduction from the complex supersymmetric N=2 sigma models built on the multiplets (2,2,0 and describing the Dolbeault complex on the manifolds with proper isometries. We study in detail the extremal two-dimensional case, when the target space metric is defined solely by the antisymmetric tensor, and show that the corresponding quantum systems reveal a hidden N=4 supersymmetry.

  18. The Process to Estimate Economical Benefits of Six Sigma Projects

    Directory of Open Access Journals (Sweden)

    Jan Kosina

    2013-07-01

    Full Text Available This paper seeks to define the process for the continuous evaluation of the financial benefits during Six Sigma project life time. The financial criteria are critical success factors of a Six Sigma project. The process has been developed as part of the six sigma project monitoring in order to estimate proper allocation of the resources taking in account the expected project benefits as well as evaluationof real achievements. The evaluation of the finacial benefits based on the quality costs is not sufficient in the real life and has to be accomplished with key financial performance indicators of the business to visualize the results. The evaluation based on the savings seems to be too difficult especially for green belts. The early involvement of the finance department in the project definition as well as ongoing evaluation is key. The defined process has been applied to real business enviroment.

  19. Lectures on nonlinear sigma-models in projective superspace

    International Nuclear Information System (INIS)

    Kuzenko, Sergei M

    2010-01-01

    N= 2 supersymmetry in four spacetime dimensions is intimately related to hyperkaehler and quaternionic Kaehler geometries. On one hand, the target spaces for rigid supersymmetric sigma-models are necessarily hyperkaehler manifolds. On the other hand, when coupled to N= 2 supergravity, the sigma-model target spaces must be quaternionic Kaehler. It is known that such manifolds of restricted holonomy are difficult to generate explicitly. Projective superspace is a field-theoretic approach to construct general N= 2 supersymmetric nonlinear sigma-models, and hence to generate new hyperkaehler and quaternionic Kaehler metrics. Intended for a mixed audience consisting of both physicists and mathematicians, these lectures provide a pedagogical introduction to the projective-superspace approach. (topical review)

  20. Role of sigma-1 receptors in neurodegenerative diseases

    Directory of Open Access Journals (Sweden)

    Linda Nguyen

    2015-01-01

    Full Text Available Neurodegenerative diseases with distinct genetic etiologies and pathological phenotypes appear to share common mechanisms of neuronal cellular dysfunction, including excitotoxicity, calcium dysregulation, oxidative damage, ER stress and mitochondrial dysfunction. Glial cells, including microglia and astrocytes, play an increasingly recognized role in both the promotion and prevention of neurodegeneration. Sigma receptors, particularly the sigma-1 receptor subtype, which are expressed in both neurons and glia of multiple regions within the central nervous system, are a unique class of intracellular proteins that can modulate many biological mechanisms associated with neurodegeneration. These receptors therefore represent compelling putative targets for pharmacologically treating neurodegenerative disorders. In this review, we provide an overview of the biological mechanisms frequently associated with neurodegeneration, and discuss how sigma-1 receptors may alter these mechanisms to preserve or restore neuronal function. In addition, we speculate on their therapeutic potential in the treatment of various neurodegenerative disorders.

  1. Lectures on nonlinear sigma-models in projective superspace

    Energy Technology Data Exchange (ETDEWEB)

    Kuzenko, Sergei M, E-mail: kuzenko@cyllene.uwa.edu.a [School of Physics M013, University of Western Australia, 35 Stirling Highway, Crawley WA 6009 (Australia)

    2010-11-05

    N= 2 supersymmetry in four spacetime dimensions is intimately related to hyperkaehler and quaternionic Kaehler geometries. On one hand, the target spaces for rigid supersymmetric sigma-models are necessarily hyperkaehler manifolds. On the other hand, when coupled to N= 2 supergravity, the sigma-model target spaces must be quaternionic Kaehler. It is known that such manifolds of restricted holonomy are difficult to generate explicitly. Projective superspace is a field-theoretic approach to construct general N= 2 supersymmetric nonlinear sigma-models, and hence to generate new hyperkaehler and quaternionic Kaehler metrics. Intended for a mixed audience consisting of both physicists and mathematicians, these lectures provide a pedagogical introduction to the projective-superspace approach. (topical review)

  2. Genome-scale reconstruction of the sigma factor network in Escherichia coli: topology and functional states

    DEFF Research Database (Denmark)

    Cho, Byung-Kwan; Kim, Donghyuk; Knight, Eric M.

    2014-01-01

    Background: At the beginning of the transcription process, the RNA polymerase (RNAP) core enzyme requires a sigma-factor to recognize the genomic location at which the process initiates. Although the crucial role of sigma-factors has long been appreciated and characterized for many individual...... to transcription units (TUs), representing an increase of more than 300% over what has been previously reported. The reconstructed network was used to investigate competition between alternative sigma-factors (the sigma(70) and sigma(38) regulons), confirming the competition model of sigma substitution...

  3. Aplicação da metodologia Lean Six Sigma para melhoria de um processo produtivo

    OpenAIRE

    Augusto Schaffer

    2016-01-01

    O Lean Six Sigma é a metodologia originada a partir da integração das metodologias Lean e Six Sigma. O Lean Six Sigma procura eliminar as perdas e reduzir os defeitos, agregando os benefícios de cada uma das duas metodologias que a dão origem. O objetivo deste trabalho é aplicar a metodologia Lean Six Sigma para melhoria de um processo produtivo. Neste trabalho é apresentada uma revisão bibliográfica sobre as metodologias Lean e Six Sigma, buscando a compreensão das origens do Lean Six Sigma,...

  4. Sigma set scattering equations in nuclear reaction theory

    International Nuclear Information System (INIS)

    Kowalski, K.L.; Picklesimer, A.

    1982-01-01

    The practical applications of partially summed versions of the Rosenberg equations involving only special subsets (sigma sets) of the physical amplitudes are investigated with special attention to the Pauli principle. The requisite properties of the transformations from the pair labels to the set of partitions labeling the sigma set of asymptotic channels are established. New, well-defined, scattering integral equations for the antisymmetrized transition operators are found which possess much less coupling among the physically distinct channels than hitherto expected for equations with kernels of equal complexity. In several cases of physical interest in nuclear physics, a single connected-kernel equation is obtained for the relevant antisymmetrized elastic scattering amplitude

  5. Dilaton gravity, Poisson sigma models and loop quantum gravity

    International Nuclear Information System (INIS)

    Bojowald, Martin; Reyes, Juan D

    2009-01-01

    Spherically symmetric gravity in Ashtekar variables coupled to Yang-Mills theory in two dimensions and its relation to dilaton gravity and Poisson sigma models are discussed. After introducing its loop quantization, quantum corrections for inverse triad components are shown to provide a consistent deformation without anomalies. The relation to Poisson sigma models provides a covariant action principle of the quantum-corrected theory with effective couplings. Results are also used to provide loop quantizations of spherically symmetric models in arbitrary D spacetime dimensions.

  6. Juego de rol Lean Six Sigma para empresas

    OpenAIRE

    Moldon Garrido, David; Porqueras Vila, Olga

    2015-01-01

    El objetivo del presente trabajo es la creación de un juego de rol que sirva a las empresas como formación. El fin de este juego es concienciar y formar a los trabajadores en la metodología Lean Six Sigma. Lean Six Sigma es una metodología centrada en la mejora continua para reducir los costes de la no calidad. Estos costes son aquellos generados por la producción de material o servicios que no cumplen los requerimientos del cliente. Creamos un juego de rol en el que los participantes form...

  7. Lean Six Sigma en las administraciones públicas

    OpenAIRE

    Chiaburu, Gheorghe

    2014-01-01

    RESUMEN: El objetivo principal de este trabajo es realizar un estudio sobre la metodología Six Sigma y la metodología Lean, evaluando su posible implementación en las Administraciones públicas. Como se muestra más adelante la unión de estas dos metodologías es más que un sistema de calidad, es una filosofía de trabajo que busca la perfección continua de los procesos. La implementación de la Six Sigma se ha realizado principalmente en industrias manufactureras y de producción y de mane...

  8. Note on off-shell relations in nonlinear sigma model

    International Nuclear Information System (INIS)

    Chen, Gang; Du, Yi-Jian; Li, Shuyi; Liu, Hanqing

    2015-01-01

    In this note, we investigate relations between tree-level off-shell currents in nonlinear sigma model. Under Cayley parametrization, all odd-point currents vanish. We propose and prove a generalized U(1) identity for even-point currents. The off-shell U(1) identity given in http://dx.doi.org/10.1007/JHEP01(2014)061 is a special case of the generalized identity studied in this note. The on-shell limit of this identity is equivalent with the on-shell KK relation. Thus this relation provides the full off-shell correspondence of tree-level KK relation in nonlinear sigma model.

  9. Symmetries and discretizations of the O(3) nonlinear sigma model

    Energy Technology Data Exchange (ETDEWEB)

    Flore, Raphael [TPI, Universitaet Jena (Germany)

    2011-07-01

    Nonlinear sigma models possess many interesting properties like asymptotic freedom, confinement or dynamical mass generation, and hence serve as toy models for QCD and other theories. We derive a formulation of the N=2 supersymmetric extension of the O(3) nonlinear sigma model in terms of constrained field variables. Starting from this formulation, it is discussed how the model can be discretized in a way that maintains as many symmetries of the theory as possible. Finally, recent numerical results related to these discretizations are presented.

  10. Hyperon sigma terms for 2+1 quark flavours

    Energy Technology Data Exchange (ETDEWEB)

    Horsley, R.; Winter, F.; Zanotti, J.M. [Edinburgh Univ. (United Kingdom). School of Physics and Astronomy; Nakamura, Y. [RIKEN Advanded Institute for Computational Science, Kobe, Hyogo (Japan); Perlt, H.; Schiller, A. [Leipzig Univ. (Germany). Inst. fuer Theoretische Physik; Pleiter, D. [Juelich Research Centre (Germany); Regensburg Univ. (Germany). Institut fuer Theoretische Physik; Rakow, P.E.L. [Liverpool Univ. (United Kingdom). Theoretical Physics Division; Schierholz, G. [Regensburg Univ. (Germany). Institut fuer Theoretische Physik; Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Stueben, H. [Konrad-Zuse-Zentrum fuer Informationstechnik Berlin (ZIB) (Germany)

    2011-10-15

    QCD lattice simulations determine hadron masses as functions of the quark masses. From the gradients of these masses and using the Feynman- Hellmann theorem the hadron sigma terms can then be determined. We use here a novel approach of keeping the singlet quark mass constant in our simulations which upon using an SU(3) flavour symmetry breaking expansion gives highly constrained (i.e. few parameter) fits for hadron masses in a multiplet. This is a highly advantageous procedure for determining the hadron mass gradient as it avoids the use of delicate chiral perturbation theory. We illustrate the procedure here by estimating the light and strange sigma terms for the baryon octet. (orig.)

  11. Classically integrable boundary conditions for symmetric-space sigma models

    International Nuclear Information System (INIS)

    MacKay, N.J.; Young, C.A.S.

    2004-01-01

    We investigate boundary conditions for the non-linear sigma model on the compact symmetric space G/H. The Poisson brackets and the classical local conserved charges necessary for integrability are preserved by boundary conditions which correspond to involutions which commute with the involution defining H. Applied to SO(3)/SO(2), the non-linear sigma model on S 2 , these yield the great circles as boundary submanifolds. Applied to GxG/G, they reproduce known results for the principal chiral model

  12. Supersymmetric sigma models and composite Yang-Mills theory

    International Nuclear Information System (INIS)

    Lukierski, J.

    1980-04-01

    We describe two types of supersymmetric sigma models: with field values in supercoset space and with superfields. The notion of Riemannian symmetric pair (H,G/H) is generalized to supergroups. Using the supercoset approach the superconformal-invariant model of composite U(n) Yang-Mills fields in introduced. In the framework of the superfield approach we present with some details two versions of the composite N=1 supersymmetric Yang-Mills theory in four dimensions with U(n) and U(m) x U(n) local invariance. We argue that especially the superfield sigma models can be used for the description of pre-QCD supersymmetric dynamics. (author)

  13. The SU(2 vertical stroke 3) spin chain sigma model

    International Nuclear Information System (INIS)

    Hernandez, R.; Lopez, E.

    2005-01-01

    The one-loop planar dilatation operator of N = 4 supersymmetric Yang-Mills is isomorphic to the hamiltonian of an integrable PSU(2,2 vertical stroke 4) spin chain. We construct the non-linear sigma model describing the continuum limit of the SU(2 vertical stroke 3) subsector of the N = 4 chain. We explicitly identify the spin chain sigma model with the one for a superstring moving in AdS 5 x S 5 with large angular momentum along the five-sphere. (Abstract Copyright [2005], Wiley Periodicals, Inc.)

  14. A lattice determination of Sigma-Lambda mixing

    Energy Technology Data Exchange (ETDEWEB)

    Horsley, R. [Edinburgh Univ. (United Kingdom). School of Physics and Astronomy; Najjar, J. [Regensburg Univ. (Germany). Institut fuer Theoretische Physik; Nakamura, Y. [RIKEN Advanced Institute for Computational Science, Kobe (Japan); Perlt, H.; Schiller, A. [Leipzig Univ. (Germany). Inst. fuer Theoretische Physik; Pleiter, D. [Forschungszentrum Juelich (Germany). Juelich Supercomputer Centre; Rakow, P.E.L. [Liverpool Univ. (United Kingdom). Theoretical Physics Division; Schierholz, G. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Stueben, H. [Hamburg Univ. (Germany). Regionales Rechenzentrum; Zanotti, J.M. [Adelaide Univ. (Australia). CSSM, Dept. of Physics; Collaboration: QCDSF-UKQCD Collaboration

    2014-11-15

    Isospin breaking effects in baryon octet (and decuplet) masses are due to a combination of up and down quark mass differences and electromagnetic effects and lead to small mass splittings. Between the Sigma and Lambda this mass splitting is much larger, this being mostly due to their different wavefunctions. However when isospin is broken, there is a mixing between between these states. We describe the formalism necessary to determine the QCD mixing matrix and hence find the mixing angle and mass splitting between the Sigma and Lambda particles due to QCD effects.

  15. CMOS sigma-delta converters practical design guide

    CERN Document Server

    De la Rosa, Jose M

    2013-01-01

    A comprehensive overview of Sigma-Delta Analog-to-Digital Converters (ADCs) and a practical guide to their design in nano-scale CMOS for optimal performance. This book presents a systematic and comprehensive compilation of sigma-delta converter operating principles, the new advances in architectures and circuits, design methodologies and practical considerations - going from system-level specifications to silicon integration, packaging and measurements, with emphasis on nanometer CMOS implementation. The book emphasizes practical design issues - from high-level behavioural modelling i

  16. The alternative sigma factor sigma B of Staphylococcus aureus modulates virulence in experimental central venous catheter-related infections.

    Science.gov (United States)

    Lorenz, Udo; Hüttinger, Christian; Schäfer, Tina; Ziebuhr, Wilma; Thiede, Arnulf; Hacker, Jörg; Engelmann, Susanne; Hecker, Michael; Ohlsen, Knut

    2008-03-01

    The impact of the alternative sigma factor sigma B (SigB) on pathogenesis of Staphylococcus aureus is not conclusively clarified. In this study, a central venous catheter (CVC) related model of multiorgan infection was used to investigate the role of SigB for the pathogenesis of S. aureus infections and biofilm formation in vivo. Analysis of two SigB-positive wild-type strains and their isogenic mutants revealed uniformly that the wild-type was significantly more virulent than the SigB-deficient mutant. The observed difference in virulence was apparently not linked to the capability of the strains to form biofilms in vivo since wild-type and mutant strains were able to produce biofilm layers inside of the catheter. The data strongly indicate that the alternative sigma factor SigB plays a role in CVC-associated infections caused by S. aureus.

  17. High resolution transmission electron microscopy studies of {sigma} phase in Ni-based single crystal superalloys

    Energy Technology Data Exchange (ETDEWEB)

    Sun Fei [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Zhang Jianxin, E-mail: jianxin@sdu.edu.cn [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Liu Pan [Institute of Microstructure and Property of Advanced Materials, Beijing University of Technology, Beijing 100124 (China); Feng Qiang [National Center for Materials Service Safety, University of Science and Technology Beijing, Beijing 100083 (China); State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China); Han Xiaodong; Mao Shengcheng [Institute of Microstructure and Property of Advanced Materials, Beijing University of Technology, Beijing 100124 (China)

    2012-09-25

    Graphical abstract: (a) TEM micrograph of {sigma} phase; (b) HRTEM image of {sigma}/{gamma} interface corresponding to the area of the white frame in (a); (c) an enlarged image of area from the white frame in (b). The combination of {sigma}/{gamma} interface appears very well, and a two-atomic-layer step is shown on the {sigma}/{gamma} interface. In addition, {sigma} phase has the orientation relationship of [0 0 1]{sub {gamma}}//[1 1 2{sup Macron }]{sub {sigma}}, (2{sup Macron} 2 0){sub {gamma}}//(1{sup Macron} 1 0){sub {sigma}}, (2{sup Macron }2{sup Macron} 0){sub {gamma}}//(1 1 1){sub {sigma}}; [0 1 1]{sub {gamma}}//[1 1 0]{sub {sigma}}, (1 1{sup Macron} 1){sub {gamma}}//(0 0 1{sup Macron }){sub {sigma}} with the {gamma} phase. Highlights: Black-Right-Pointing-Pointer Elemental characteristic of {sigma} phase is studied by HAADF techniques and EDS analysis. Black-Right-Pointing-Pointer Interfacial characteristics of {sigma}/{gamma} interface are revealed by HRTEM. Black-Right-Pointing-Pointer An atomic structural {sigma}/{gamma} interface with a two-atomic-layer step has been proposed. - Abstract: By means of high resolution transmission electron microscopy (HRTEM) and high-angle annular dark-field image technique (HAADF), morphological of plate-shaped {sigma} phase and interfacial characteristics between plate-shaped {sigma} phase and {gamma} phase in Ni-based single crystal superalloys have been studied. On the basis of HRTEM observations, an atomic structural interface between {sigma} phase and {gamma} phase with a step has been proposed. {sigma} Phase has the relationship of [0 0 1]{sub {gamma}}//[1 1 2{sup Macron }]{sub {sigma}}, (2{sup Macron} 2 0){sub {gamma}}//(1{sup Macron} 1 0){sub {sigma},} (2{sup Macron }2{sup Macron} 0){sub {gamma}}//(1 1 1){sub {sigma}}; [0 1 1]{sub {gamma}}//[1 1 0]{sub {sigma}}, (1 1{sup Macron} 1){sub {gamma}}//(0 0 1{sup Macron }){sub {sigma}} with the {gamma} phase. The compositional characteristics of the {sigma} phase which

  18. Characterization of the SPS 800MHz travelling wave cavities.

    CERN Document Server

    Bazyl, Dmitry

    2015-01-01

    It is well known that HOMs in RF cavities are a potentially dangerous source of beam impedance. Therefore, HOMs (both longitudinal and transverse) can drive the beam unstable . The 800MHz cavities of the SPS were studied in the past. However, very little documentation was left behind. Currently, the performance of the SPS is limited by a longitudinal beam instability. In order to study this instability, an accurate impedance model of the whole SPS is needed.

  19. Polarization observations of four southern pulsars at 1560 MHz

    Science.gov (United States)

    Wu, Xin-Ji; Manchester, R. N.; Lyne, A. G.

    1991-12-01

    Some interesting results from the mean pulse polarization observations of four southern pulsars made at the Australian National Radio Astronomy Observatory, Parkes, using the 64-m telescope in June and July, 1988, are presented. The 2 x 16 x 5 MHz filter system from Jodrell Bank has proved excellent in dedispersing the pulse signals and measuring their polarization properties. Data for the four pulsars are given in some detail, and their spectral behavior is discussed.

  20. Status of HLT1 sequence and path towards 30 MHz

    CERN Document Server

    De Cian, Michel; Gligorov, Vladimir; Hasse, Christoph; Hulsbergen, Wouter; Latham, Thomas Edward; Ponce, Sebastien; Quagliani, Renato; Schreiner, Henry Fredrick; Stemmle, Simon Benedikt; Van Tilburg, Jeroen; Zdybal, Milosz Jerzy; Williams, J Michael

    2018-01-01

    We present the current status of the HLT1 reconstruction sequence for the LHCb upgrade, both in terms of the number of events which can be processed per second and the achievable physics performance on a selected range of benchmark modes. We present detailed profiling of the various algorithms, describe the bottlenecks, and outline a strategy towards an HLT1 able to process the LHCb upgrade data at 30 MHz

  1. Effect of 2 MHz ultrasound irradiation on Pisum sativum roots

    International Nuclear Information System (INIS)

    Miller, M.W.; Voorhees, S.M.; Carstensen, E.L.; Kaufman, G.E.

    1976-01-01

    The effect of 2 MHz ultrasound at intensity levels from 2.5 to 22 W/cm 2 on the growth rate and mitotic index of Pisum sativum roots was studied. The ultrasound produced an immediate reduction in the growth rate on the first postexposure day, followed by a gradual recovery to the control value. Ultrasound reduced the root meristem mitotic index. Intensity- and time-dependent relations were found for the growth rate and mitotic index reductions

  2. Design of 1 MHz solid state high frequency power supply

    International Nuclear Information System (INIS)

    Parmar, Darshan Kumar; Singh, N.P.; Gajjar, Sandip

    2015-01-01

    A High Voltage High Frequency (HVHF) Power supply is used for various applications, like AM Transmitters, metallurgical applications, Wireless Power Transfer, RF Ion Sources, etc. The Ion Source for a Neutral beam Injector at ITER-India uses inductively coupled power source at High Frequency (∼ 1 MHz). Switching converter based topology used to generate 1 MHz sinusoidal output is expected to have advantages on efficiency and reliability as compared to traditional RF Tetrode tubes based oscillators. In terms of Power Electronics, thermal and power coupling issues are major challenges at such a high frequency. A conceptual design for a 200 kW, 1 MHz power supply and a prototype design for a 600W source been done. The prototype design is attempted with Class-E amplifier topology where a MOSFET is switched resonantly. The prototype uses two low power modules and a ferrite combiner to add the voltage and power at the output. Subsequently solution with class-D H-Bridge configuration have been evaluated through simulation where module design is stable as switching device do not participate in resonance, further switching device voltage rating is substantially reduced. The rating of the modules is essentially driven by the maximum power handling capacity of the MOSFETs and ferrites in the combiner circuit. The output passive network including resonance tuned network and impedance matching network caters for soft switching and matches the load impedance to 50 ohm respectively. This paper describes the conceptual design of a 200 kW power supply and experimental results of the prototype 600 W, 1 MHz source. (author)

  3. The quiet Sun brightness temperature at 408 MHz

    International Nuclear Information System (INIS)

    Avignon, Y.; Lantos, P.; Palagi, F.; Patriarchi, P.

    1975-01-01

    The flux of the radio quiet Sun and the brightness temperature at 408 MHz (73cm) are derived from measurements with the E-W Nancay interferometer and the E-W arm of the Medicina North Cross. It is shown that the lowest envelopes, which defined the radio quiet Sun, correspond to transits of extended coronal holes across the disk of the Sun. (Auth.)

  4. Development of a high-power 432 MHz DTL

    International Nuclear Information System (INIS)

    Naito, F.; Kato, T.; Takasaki, E.; Yamazaki, Y.; Kawasumi, T.; Suzuki, K.; Iino, Y.

    1992-01-01

    A high-power model of a 432 MHz Drift-Tube Linac is under construction. It will accelerate H - ions from 3 to 5.4 MeV, and is a prototype of the DTL for the Japanese Hadron Project. Several new techniques have been developed for constructing the DTL: fabricating and assembling methods of permanent quadrupole magnet and a drift tube, alignment of the drift tube, and a method of connecting the tanks. (Author) 6 refs., 5 figs

  5. Spectroscopy of radio sources from the Parkes 2700 MHz survey

    International Nuclear Information System (INIS)

    Thompson, D.J.; Djorgovski, S.; De Carvalho, R.

    1990-01-01

    The results of long-slit CCD spectroscopy on 37 objects from the Parkes 2700 MHz survey are presented, with data for an additional two companion objects. Eight of the objects are quasars, six more are AGNs, and five more are radio galaxies. Seventeen of the objects observed are stars and, thus, probable misidentifications. Three objects show featureless spectra and are identified as possible BL Lac objects. Spectra are presented for a total of 20 objects. 20 refs

  6. Prototype 350 MHz niobium spoke-loaded cavities

    International Nuclear Information System (INIS)

    Delayen, J. R.; Kedzie, M.; Mammosser, J.; Piller, C.; Shepard, K. W.

    1999-01-01

    This paper reports the development of 350 MHz superconducting cavities of a spoke-loaded geometry, intended for the velocity range 0.2 < v/c < 0.6. Two prototype single-cell cavities have been designed, one optimized for velocity v/c = 0.4, and the other for v/c = 0.29. Construction of the prototype niobium cavities is nearly complete. Details of the design and construction are discussed, along with the results of cold tests

  7. Prototype 350 MHz niobium spoke-loaded cavities.

    Energy Technology Data Exchange (ETDEWEB)

    Delayen, J. R.; Kedzie, M.; Mammosser, J.; Piller, C.; Shepard, K. W.

    1999-05-10

    This paper reports the development of 350 MHz superconducting cavities of a spoke-loaded geometry, intended for the velocity range 0.2 < v/c < 0.6. Two prototype single-cell cavities have been designed, one optimized for velocity v/c = 0.4, and the other for v/c = 0.29. Construction of the prototype niobium cavities is nearly complete. Details of the design and construction are discussed, along with the results of cold tests.

  8. Design of 1 MHz Solid State High Frequency Power Supply

    Science.gov (United States)

    Parmar, Darshan; Singh, N. P.; Gajjar, Sandip; Thakar, Aruna; Patel, Amit; Raval, Bhavin; Dhola, Hitesh; Dave, Rasesh; Upadhay, Dishang; Gupta, Vikrant; Goswami, Niranjan; Mehta, Kush; Baruah, Ujjwal

    2017-04-01

    High Frequency Power supply (HFPS) is used for various applications like AM Transmitters, metallurgical applications, Wireless Power Transfer, RF Ion Sources etc. The Ion Source for a Neutral beam Injector at ITER-India uses inductively coupled power source at High Frequency (∼1 MHz). Switching converter based topology used to generate 1 MHz sinusoidal output is expected to have advantages on efficiency and reliability as compared to traditional RF Tetrode tubes based oscillators. In terms of Power Electronics, thermal and power coupling issues are major challenges at such a high frequency. A conceptual design for a 200 kW, 1 MHz power supply and a prototype design for a 600 W source been done. The prototype design is attempted with Class-E amplifier topology where a MOSFET is switched resonantly. The prototype uses two low power modules and a ferrite combiner to add the voltage and power at the output. Subsequently solution with Class-D H-Bridge configuration have been evaluated through simulation where module design is stable as switching device do not participate in resonance, further switching device voltage rating is substantially reduced. The rating of the modules is essentially driven by the maximum power handling capacity of the MOSFETs and ferrites in the combiner circuit. The output passive network including resonance tuned network and impedance matching network caters for soft switching and matches the load impedance to 50ohm respectively. This paper describes the conceptual design of a 200 kW high frequency power supply and experimental results of the prototype 600 W, 1 MHz source.

  9. Velocities of Auroral Coherent Echoes At 12 and 144 Mhz

    Science.gov (United States)

    Koustov, A. V.; Danskin, D. W.; Makarevitch, R. A.; Uspensky, M. V.; Janhunen, P.; Nishitani, N.; Nozawa, N.; Lester, M.; Milan, S.

    Two Doppler coherent radar systems are currently working at Hankasalmi, Finland, the STARE and CUTLASS radars operating at 144 MHz and 12 MHz, respectively. The STARE beam 3 is nearly co-located with the CUTLASS beam 5 providing an opportunity for echo velocity comparison along the same direction but at significantly different radar frequencies. In this study we consider one event when STARE radar echoes are detected t the same ranges as CUTLASS radar echoes. The observations are complemented by EISCAT measurements of the ionospheric electric field and elec- tron density behavior at one range of 900 km. Two separate situations are studied; for the first one, CUTLASS observed F-region echoes (including the range of the EIS- CAT measurements) while for the second one CUTLASS observed E-region echoes. In both cases STARE E-region measurements were available. We show that F-region CUTLASS velocities agree well with the convection component along the CUTLASS radar beam while STARE velocities are sometimes smaller by a factor of 2-3. For the second case, STARE velocities are found to be either smaller or larger than CUTLASS velocities, depending on range. Plasma physics of E- and F-region irregularities is dis- cussed in attempt to explain inferred relationship between various velocities. Special attention is paid to ionospheric refraction that is important for the detection of 12-MHz echoes.

  10. Assessment of cutaneous radiation fibrosis by 20 MHz-sonography

    International Nuclear Information System (INIS)

    Gottloeber, P.; Braun-Falco, B.; Plewig, G.; Kerscher, M.; Peter, R.U.; Nadeshina, N.

    1996-01-01

    Radiation fibrosis is the cardinal symptom of the chronicle stage of the cutaneous radiation syndrome. The degree of cutaneous fibrosis can clinically be estimated by palpation. High-frequency 20 MHz-sonography is an established, noninvasive procedure, which renders an exact determination of skin thickness and additionally densitometry is possible. We investigated 15 survivors of the Chernobyl accident in 1986, who developed symptoms of the chronic stage of the cutaneous radiation syndrome. We determined skin thickness and echogenicity of skin areas clinically suggestive of radiation fibrosis before, during and after treatment. 20 MHz-sonography showed a distinct enlargement of the echorich corium and a reduction of the subcutaneous fatty tissue in comparison with the unaffected, contralateral skin, here demonstrating typical features of radiation fibrosis, namely dermal fibrosis and reactive pseudoatrophy and fatty tissue. The histology presented an increase and swelling of the collagen fibers and atypical fibroblastic cells. The patients received treatment with low-dose interferon y (Polyfcron R , 3 x 50μg s.C., three times per week) up to 30 months. A marked reduction of skin thickness and echogenicity reaching nearly normal values could be observed. We conclude that 20 MHz-sonography is an easy to apply, noninvasive, well established procedure to quantify cutaneous radiation fibrosis and to assess therapeutic outcome

  11. The LANSCE 805 MHZ RF System History and Status

    CERN Document Server

    Lynch, Michael; Tallerico, Paul J

    2005-01-01

    The Los Alamos Neutron Science Center (LANSCE) linear accelerator runs at 201.25 MHz for acceleration to 100 MeV. The remainder of the acceleration to 800 MeV is at 805 MHz. This is done with 44 accelerator cavity stages driven by 805 MHz klystrons. Each klystron has a peak power capability of 1.25 MeV. Originally, 97 klystrons were purchased, which was 70 from Varian/CPI and 27 from Litton. The 44 RF systems are laid out in sectors with either 6 or 7 klystrons per sector. The klystrons in each sector are powered from a common HV sytem. The current arrangement uses the Varian/CPI klystrons in 6 of the 7 sectors and Litton klystrons in the remaining sector. With that arrangement there are 38 CPI klystrons installed and 1 spare klystron per sector and 6 Litton klystrons installed in the final sector with 2 spares. The current average life of all of the operating and spare klystrons (52 total) is >112,000 filament hours and >93,000 HV hours. That is three times the typical klystron lifetime today f...

  12. A 2 MHz 3-port analog isolation and fanout module

    International Nuclear Information System (INIS)

    Beadle, E.R.

    1995-01-01

    In many accelerator based data acquisition systems, signal isolation is a necessary feature so ground loops are avoided. Here, a 3-port isolated circuit providing 1:3 fanout, buffering and amplification over a multi-megahertz bandwidth is presented. The circuit accepts a single input and drives 3 independently isolated output channels, up to ± 10 V into 50 ohms. The input and output isolation is supplied via a dual optocoupler, and the power isolation is achieved with DC/DC converters. In each channel, a voltage feedback amplifier is used in combination with the optocoupler to form a transimpedance configuration with the gain-bandwidth product (GBP) set by a pair of resistors. The feedback amplifier linearizes the optocoupler transfer characteristics using a servo technique and also controls the circuit drift, nonlinearity, and bandwidth. The circuit has demonstrated long-term drift of 4 MHz, and a SNR of >55 db in a 1 MHz bandwidth with < 1% THD for a 10 V amplitude sinusoidal input. With few modifications, this design is capable of providing input/output gain and bandwidth in the range of 10--50 MHz

  13. Design of 118 MHz twelfth harmonic cavity of APS PAR

    International Nuclear Information System (INIS)

    Kang, Y.W.; Kustom, R.L.; Bridges, J.F.

    1992-01-01

    Two radio frequency (RF) cavities are needed in the Positron Accumulator Ring (PAR) of the Advanced Photon Source. One is for the first harmonic frequency at 9.8 MHz, and the other is for the twelfth harmonic frequency at 118 MHz. This note reports on the design of the 118 MHz RF cavity. Computer models are used to find the mode frequencies, impedances, Q-factors, and field distributions in the cavity. The computer codes MAFIA, URMEL, and URMEL-T are useful tools which model and simulate the resonance characteristics of a cavity. These codes employ the finite difference method to solve Maxwell's equations. MAFIA is a three-dimensional problem solver and uses square patches to approximate the inner surface of a cavity. URMEL and URMEL-T are two-dimensional problem solvers and use rectangular and triangular meshes, respectively. URMEL-T and MAFIA can handle problems with arbitrary dielectric materials located inside the boundary. The cavity employs a circularly cylindrical ceramic window to limit the vacuum to the beam pipe. The ceramic window used in the modeling will have a wall thickness of 0.9 cm. This wall thickness is not negligible in determining the resonant frequencies of the cavity. In the following, results of two- and three-dimensional modeling of the cavities using the URMEL-T and MAFIA codes are reported

  14. An Automated 476 MHz RF Cavity Processing Facility at SLAC

    CERN Document Server

    McIntosh, P; Schwarz, H

    2003-01-01

    The 476 MHz accelerating cavities currently used at SLAC are those installed on the PEP-II B-Factory collider accelerator. They are designed to operate at a maximum accelerating voltage of 1 MV and are routinely utilized on PEP-II at voltages up to 750 kV. During the summer of 2003, SPEAR3 will undergo a substantial upgrade, part of which will be to replace the existing 358.54 MHz RF system with essentially a PEP-II high energy ring (HER) RF station operating at 476.3 MHz and 3.2 MV (or 800 kV/cavity). Prior to installation, cavity RF processing is required to prepare them for use. A dedicated high power test facility is employed at SLAC to provide the capability of conditioning each cavity up to the required accelerating voltage. An automated LabVIEW based interface controls and monitors various cavity and test stand parameters, increasing the RF fields accordingly such that stable operation is finally achieved. This paper describes the high power RF cavity processing facility, highlighting the features of t...

  15. Reduction of environmental MHz noise for SQUID application

    Energy Technology Data Exchange (ETDEWEB)

    Araya, T. [Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan)]. E-mail: araya@sup.ee.es.osaka-u.ac.jp; Kitamura, Y. [Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan); Kamishiro, M. [Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan); Sakuta, K. [Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan); Itozaki, H. [Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan)]. E-mail: itozaki@ee.es.osaka-u.ac.jp

    2006-10-01

    It is important to remove large environmental noise in measurement using SQUIDs without magnetic shielding. Active noise control (ANC) is an effective method to remove the environmental noise. The environmental noise has been reduced by the ANC system in the radio frequency region around MHz. The anti-phase waves of the environmental noise should be generated by this system. The ANC system including the phase and amplitude control circuit was developed to make the anti-phase waves in the MHz region. In this paper, sinusoidal waves with a MHz frequency were used as the environmental noise. When a coil antenna was used for a receiver antenna, this ANC system suppressed these sinusoidal waves to the white noise level about 40 dB. When we used a SQUID as a receiver antenna, we also cancelled sinusoidal waves to the white noise level by this system. This shows that the ANC system is useful to reduce an environmental noise when this ANC system is developed to cancel multi-frequency noise.

  16. Reduction of environmental MHz noise for SQUID application

    International Nuclear Information System (INIS)

    Araya, T.; Kitamura, Y.; Kamishiro, M.; Sakuta, K.; Itozaki, H.

    2006-01-01

    It is important to remove large environmental noise in measurement using SQUIDs without magnetic shielding. Active noise control (ANC) is an effective method to remove the environmental noise. The environmental noise has been reduced by the ANC system in the radio frequency region around MHz. The anti-phase waves of the environmental noise should be generated by this system. The ANC system including the phase and amplitude control circuit was developed to make the anti-phase waves in the MHz region. In this paper, sinusoidal waves with a MHz frequency were used as the environmental noise. When a coil antenna was used for a receiver antenna, this ANC system suppressed these sinusoidal waves to the white noise level about 40 dB. When we used a SQUID as a receiver antenna, we also cancelled sinusoidal waves to the white noise level by this system. This shows that the ANC system is useful to reduce an environmental noise when this ANC system is developed to cancel multi-frequency noise

  17. Environmental Professional’s Guide to Lean and Six Sigma: Executive Summary

    Science.gov (United States)

    Introduction to the guide that describes how Lean and Six Sigma relate to the environment and provides guidance on how environmental professionals can connect with Lean and Six Sigma activities to generate better environmental and operational results.

  18. IceBridge Sigma Space Lidar L0 Raw Time-of-Flight Data

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA IceBridge Sigma Space Lidar L0 Raw Time-of-Flight Data (ILSIG0) contain raw time-of-flight values for Antarctica and Greenland using the Sigma Space Lidar....

  19. Current algebra of classical non-linear sigma models

    International Nuclear Information System (INIS)

    Forger, M.; Laartz, J.; Schaeper, U.

    1992-01-01

    The current algebra of classical non-linear sigma models on arbitrary Riemannian manifolds is analyzed. It is found that introducing, in addition to the Noether current j μ associated with the global symmetry of the theory, a composite scalar field j, the algebra closes under Poisson brackets. (orig.)

  20. SIGMA Release v1.2 - Capabilities, Enhancements and Fixes

    Energy Technology Data Exchange (ETDEWEB)

    Mahadevan, Vijay [Argonne National Lab. (ANL), Argonne, IL (United States); Grindeanu, Iulian R. [Argonne National Lab. (ANL), Argonne, IL (United States); Ray, Navamita [Argonne National Lab. (ANL), Argonne, IL (United States); Jain, Rajeev [Argonne National Lab. (ANL), Argonne, IL (United States); Wu, Danqing [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-09-30

    In this report, we present details on SIGMA toolkit along with its component structure, capabilities, and feature additions in FY15, release cycles, and continuous integration process. These software processes along with updated documentation are imperative to successfully integrate and utilize in several applications including the SHARP coupled analysis toolkit for reactor core systems funded under the NEAMS DOE-NE program.

  1. Generic Lean Six Sigma project definitions in financial services

    NARCIS (Netherlands)

    de Koning, H.; de Mast, J.; Does, R.J.M.M.; Vermaat, T.; Simons, S.

    2008-01-01

    Lean Six Sigma (LSS) is applied in financial service organizations to improve operational efficiency and effectiveness. LSS prescribes that these improvements are designed and implemented by projects. The purpose of this article is to facilitate the process of defining LSS projects in finance,

  2. Applying Lean and Six Sigma in financial service

    NARCIS (Netherlands)

    Does, R.J.M.M.; de Koning, H.; Anthony, J.; Kumar, M.

    2006-01-01

    Abstract Lean and Six Sigma have gone through parallel developments in recent years. Originally applied to a small range of industries, both approaches are now also used widely in healthcare, administration and service. A recent development is the integration of the two approaches. In this paper we

  3. Lean-Six Sigma: tools for rapid cycle cost reduction.

    Science.gov (United States)

    Caldwell, Chip

    2006-10-01

    Organizational costs can be grouped as process cost, cost of quality, and cost of poor quality. Providers should train managers in the theory and application of Lean-Six Sigma, including the seven categories of waste and how to remove them. Healthcare financial executives should work with managers in eliminating waste to improve service and reduce costs.

  4. Using Six Sigma and Lean methodologies to improve OR throughput.

    Science.gov (United States)

    Fairbanks, Catharine B

    2007-07-01

    Improving patient flow in the perioperative environment is challenging, but it has positive implications for both staff members and for the facility. One facility in vermont improved patient throughput by incorporating Six Sigma and Lean methodologies for patients undergoing elective procedures. The results of the project were significantly improved patient flow and increased teamwork and pride among perioperative staff members. (c) AORN, Inc, 2007.

  5. Application of Six Sigma methodology to a diagnostic imaging process.

    Science.gov (United States)

    Taner, Mehmet Tolga; Sezen, Bulent; Atwat, Kamal M

    2012-01-01

    This paper aims to apply the Six Sigma methodology to improve workflow by eliminating the causes of failure in the medical imaging department of a private Turkish hospital. Implementation of the design, measure, analyse, improve and control (DMAIC) improvement cycle, workflow chart, fishbone diagrams and Pareto charts were employed, together with rigorous data collection in the department. The identification of root causes of repeat sessions and delays was followed by failure, mode and effect analysis, hazard analysis and decision tree analysis. The most frequent causes of failure were malfunction of the RIS/PACS system and improper positioning of patients. Subsequent to extensive training of professionals, the sigma level was increased from 3.5 to 4.2. The data were collected over only four months. Six Sigma's data measurement and process improvement methodology is the impetus for health care organisations to rethink their workflow and reduce malpractice. It involves measuring, recording and reporting data on a regular basis. This enables the administration to monitor workflow continuously. The improvements in the workflow under study, made by determining the failures and potential risks associated with radiologic care, will have a positive impact on society in terms of patient safety. Having eliminated repeat examinations, the risk of being exposed to more radiation was also minimised. This paper supports the need to apply Six Sigma and present an evaluation of the process in an imaging department.

  6. Application of Six Sigma methodology to a cataract surgery unit.

    Science.gov (United States)

    Taner, Mehmet Tolga

    2013-01-01

    The article's aim is to focus on the application of Six Sigma to minimise intraoperative and post-operative complications rates in a Turkish public hospital cataract surgery unit. Implementing define-measure-analyse-improve and control (DMAIC) involves process mapping, fishbone diagrams and rigorous data-collection. Failure mode and effect analysis (FMEA), pareto diagrams, control charts and process capability analysis are applied to redress cataract surgery failure root causes. Inefficient skills of assistant surgeons and technicians, low quality of IOLs used, wrong IOL placement, unsystematic sterilisation of surgery rooms and devices, and the unprioritising network system are found to be the critical drivers of intraoperative-operative and post-operative complications. Sigma level was increased from 2.60 to 3.75 subsequent to extensive training of assistant surgeons, ophthalmologists and technicians, better quality IOLs, systematic sterilisation and air-filtering, and the implementation of a more sophisticated network system. This article shows that Six Sigma measurement and process improvement can become the impetus for cataract unit staff to rethink their process and reduce malpractices. Measuring, recording and reporting data regularly helps them to continuously monitor their overall process and deliver safer treatments. This is the first Six Sigma ophthalmology study in Turkey.

  7. Why all this fuss over a few Sigma ?

    CERN Multimedia

    Patrice Loïez

    2001-01-01

    Sigma, the standard deviation, is the quantity used most often by physicists to express the strength of evidence for a new phenomenon. It is the way they measure the distance between the data observed and the data expected if there were no new phenomenon. What that means is best understood by taking a more familiar example : toss a fair coin (See Bulletin)

  8. Soliton surfaces associated with sigma models: differential and algebraic aspects

    International Nuclear Information System (INIS)

    Goldstein, P P; Grundland, A M; Post, S

    2012-01-01

    In this paper, we consider both differential and algebraic properties of surfaces associated with sigma models. It is shown that surfaces defined by the generalized Weierstrass formula for immersion for solutions of the CP N-1 sigma model with finite action, defined in the Riemann sphere, are themselves solutions of the Euler–Lagrange equations for sigma models. On the other hand, we show that the Euler–Lagrange equations for surfaces immersed in the Lie algebra su(N), with conformal coordinates, that are extremals of the area functional, subject to a fixed polynomial identity, are exactly the Euler–Lagrange equations for sigma models. In addition to these differential constraints, the algebraic constraints, in the form of eigenvalues of the immersion functions, are systematically treated. The spectrum of the immersion functions, for different dimensions of the model, as well as its symmetry properties and its transformation under the action of the ladder operators are discussed. Another approach to the dynamics is given, i.e. description in terms of the unitary matrix which diagonalizes both the immersion functions and the projectors constituting the model. (paper)

  9. Practical Design of Delta-Sigma Multiple Description Audio Coding

    DEFF Research Database (Denmark)

    Leegaard, Jack Højholt; Østergaard, Jan; Jensen, Søren Holdt

    2014-01-01

    It was recently shown that delta-sigma quantization (DSQ) can be used for optimal multiple description (MD) coding of Gaussian sources. The DSQ scheme combined oversampling, prediction, and noise-shaping in order to trade off side distortion for central distortion in MD coding. It was shown that ...

  10. Strategically Focused Training in Six Sigma Way: A Case Study

    Science.gov (United States)

    Pandey, Ashish

    2007-01-01

    Purpose: The purpose of the current study is to examine the utility of Six Sigma interventions as a performance measure and explore its applicability for making the training design and delivery operationally efficient and strategically effective. Design/methodology/approach: This is a single revelatory case study. Data were collected from multiple…

  11. Using Six-Sigma To Change and Measure Improvement.

    Science.gov (United States)

    Feld, Karl G.; Stone, William K.

    2002-01-01

    Explains why Honeywell's Market Research Department replaced its traditional data collection and paper-based tabulation with blended modes, including electronic interviewing and real-time reporting. Describes how the Six-Sigma quality control process demonstrated that a hybrid approach with blended modes and Web-based reporting tools could deliver…

  12. A review of Lean Six Sigma deployment and maturity models

    NARCIS (Netherlands)

    Lameijer, B.A.; de Mast, J.; Does, R.J.M.M.

    2017-01-01

    For guidance in implementing Lean Six Sigma (LSS), both the academic and the practitioners’ literature offer deployment models and models for assessing the implementation’s maturity. This paper makes a critical appraisal of the quality and usefulness of a sample of 19 such models. The appraisal

  13. A rational reconstruction of Six Sigma's Breakthrough Cookbook

    NARCIS (Netherlands)

    de Koning, H.; de Mast, J.

    2006-01-01

    Purpose: The purpose of this paper is to develop a consistent and crystallized exposition of Six-Sigma's methodology for improvement projects, which could serve as a basis for subsequent scientific research of the method. Design/methodology/approach: The paper shows that reformulation of imprecise

  14. Polarization-induced sigma-holes and hydrogen bonding

    Czech Academy of Sciences Publication Activity Database

    Hennemann, M.; Murray, J. S.; Politzer, P.; Riley, Kevin Eugene; Clark, T.

    2012-01-01

    Roč. 18, č. 6 (2012), s. 2461-2469 ISSN 1610-2940 Institutional research plan: CEZ:AV0Z40550506 Keywords : hydrogen bond * sigma-hole * polarization * field effect * ab initio calculation Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.984, year: 2012

  15. Sigma-convergence of stationary Navier-Stokes type equations

    Directory of Open Access Journals (Sweden)

    Gabriel Nguetseng

    2009-06-01

    Full Text Available In the framework of homogenization theory, the Sigma-convergence method is carried out on stationary Navier-Stokes type equations on a fixed domain. Our main tools are the two-scale convergence concept and the so-called homogenization algebras.

  16. Generic Lean Six Sigma project definitions in publishing

    NARCIS (Netherlands)

    de Koning, H.; Does, R.J.M.M.; Groen, A.; Kemper, B.P.H.

    2010-01-01

    Purpose - Many companies in the publishing industry are facing the task of developing new business models and becoming more efficient and effective in execution. Lean Six Sigma (LSS) is a unified framework for systematically developing efficiency and quality improvements; it can help realize

  17. SIGMA Release v1.2 - Capabilities, Enhancements and Fixes

    International Nuclear Information System (INIS)

    Mahadevan, Vijay; Grindeanu, Iulian R.; Ray, Navamita; Jain, Rajeev; Wu, Danqing

    2015-01-01

    In this report, we present details on SIGMA toolkit along with its component structure, capabilities, and feature additions in FY15, release cycles, and continuous integration process. These software processes along with updated documentation are imperative to successfully integrate and utilize in several applications including the SHARP coupled analysis toolkit for reactor core systems funded under the NEAMS DOE-NE program.

  18. Nonlinearities in SC Delta-Sigma A/D Converters

    DEFF Research Database (Denmark)

    Steensgaard-Madsen, Jesper

    1998-01-01

    The effects of using nonlinear low-gain opamps in switched-capacitor delta-sigma modulators are analyzed. Using unconventional topologies, the state variables are made essentially uncorrelated with the input signal, hence opamp nonlinearity will cause very little harmonic distortion. Nonlinearity...

  19. Sigma factors in a thousand E. coli genomes

    DEFF Research Database (Denmark)

    Cook, Helen Victoria; Ussery, David

    2013-01-01

    , 2013), only less than half (983) are of sufficient quality to use in comparative genomic work. Unfortunately, even some of the ‘complete’ E. coli genomes are in pieces, and a few ‘draft’ genomes are good quality. Six of the seven known sigma factors in E. coli strain K‐12 are extremely well conserved...

  20. Gustav Naan ja Sigma Tau / Arvo Pesti, Madli Pesti

    Index Scriptorium Estoniae

    Pesti, Arvo, 1956-2010

    2009-01-01

    Füüsik, kosmoloog ja ühiskonnategelane Gustav Naanist. Merle Karusoo dokumentaallavastusest "Sigma Tau-C705", mis põhineb Enn Vetemaa ja Erki Aule näidendil "Gustav Naani hiilgus ja viletsus". Esietendus 16. märtsil 2008 Eesti Draamateatris

  1. Six Sigma in Health Care: Lessons learned from a Hospital

    NARCIS (Netherlands)

    van den Heuvel, J.; Does, R.J.M.M.; Verver, J.P.S.

    2005-01-01

    Six Sigma is a quality improvement approach aimed at optimising processes while reducing defects and costs. It has been developed and is widely used in industry and recently has been introduced, on a limited scale, in healthcare. In this article, we discuss the results of the implementation of Six

  2. A Novel Dual-Band Rectenna for Ambient RF Energy Harvesting at GSM 900 MHz and 1800 MHz

    Directory of Open Access Journals (Sweden)

    Dinh Khanh Ho

    2017-06-01

    Full Text Available This paper presents a novel dual-band rectenna for RF energy harvesting system. This rectenna is created from a dual-band antenna and a dual-band rectifier which operates at GSM bands (900 MHz and 1800 MHz. The printed monopole antenna is miniaturized by two meander-lines. The received signal from the receiving antenna is rectified by a voltage double using Schottky diode SMS-7630. The rectifier is optimized for low input power level of -20dBm using harmonic balance. Prototype is designed and fabricated. The simulation is validated by measurement with power conversion efficiency of 20% and 40.8% (in measurement at the input power level of -20dBm. The proposed rectenna has output voltage from 183-415 mV. From the measured results, this rectenna provides the possibility to harvest the ambient electromagnetic energy for powering low-power electronic devices.

  3. Single-Station Sigma for the Iranian Strong Motion Stations

    Science.gov (United States)

    Zafarani, H.; Soghrat, M. R.

    2017-11-01

    In development of ground motion prediction equations (GMPEs), the residuals are assumed to have a log-normal distribution with a zero mean and a standard deviation, designated as sigma. Sigma has significant effect on evaluation of seismic hazard for designing important infrastructures such as nuclear power plants and dams. Both aleatory and epistemic uncertainties are involved in the sigma parameter. However, ground-motion observations over long time periods are not available at specific sites and the GMPEs have been derived using observed data from multiple sites for a small number of well-recorded earthquakes. Therefore, sigma is dominantly related to the statistics of the spatial variability of ground motion instead of temporal variability at a single point (ergodic assumption). The main purpose of this study is to reduce the variability of the residuals so as to handle it as epistemic uncertainty. In this regard, it is tried to partially apply the non-ergodic assumption by removing repeatable site effects from total variability of six GMPEs driven from the local, Europe-Middle East and worldwide data. For this purpose, we used 1837 acceleration time histories from 374 shallow earthquakes with moment magnitudes ranging from M w 4.0 to 7.3 recorded at 370 stations with at least two recordings per station. According to estimated single-station sigma for the Iranian strong motion stations, the ratio of event-corrected single-station standard deviation ( Φ ss) to within-event standard deviation ( Φ) is about 0.75. In other words, removing the ergodic assumption on site response resulted in 25% reduction of the within-event standard deviation that reduced the total standard deviation by about 15%.

  4. Wideband Bandpass Filter with High Selectivity and an Adjustable Notched-band Adopting a Multi-mode Resonator

    Science.gov (United States)

    Ma, Xing-Bing; Jiang, Ting

    2018-04-01

    A wideband bandpass filter (BPF) with an adjustable notched-band and high selectivity is proposed. The proposed BPF consists of a multi-mode resonator (MMR), two λ/2 resonators, and I/O feed lines with 50 ohm characteristic impedance. The MMR, connected as a whole by a wide stub, is composed of one I-shaped resonator and two open-loop resonators. Tightly coupling is built between MMR and λ/2 resonators. I/O feed lines are directly connected with two λ/2 resonators, respectively. Due to the use of tapped-line coupling, one transmission zero (TZ) is formed near low-edge of aim passband. High-edge of passband with one attendant TZ can be tuned to desired location by adjusting bottom-side position of used wide stub or bottom-side length of I-shaped resonator in MMR. The top-side length of I-shaped resonator is applied to improve upper stopband performance and shift undesired resonant mode of MMR near high-edge of aim passband to proper frequency point. The notched-band in aim passband is dominated by top-side position of wide stub in MMR. Good agreement is observed between simulated and measured results.

  5. A Hybrid Circuit for Spoof Surface Plasmons and Spatial Waveguide Modes to Reach Controllable Band-Pass Filters.

    Science.gov (United States)

    Zhang, Qian; Zhang, Hao Chi; Wu, Han; Cui, Tie Jun

    2015-11-10

    We propose a hybrid circuit for spoof surface plasmon polaritons (SPPs) and spatial waveguide modes to develop new microwave devices. The hybrid circuit includes a spoof SPP waveguide made of two anti-symmetric corrugated metallic strips and a traditional substrate integrated waveguide (SIW). From dispersion relations, we show that the electromagnetic waves only can propagate through the hybrid circuit when the operating frequency is less than the cut-off frequency of the SPP waveguide and greater than the cut-off frequency of SIW, generating efficient band-pass filters. We demonstrate that the pass band is controllable in a large range by designing the geometrical parameters of SPP waveguide and SIW. Full-wave simulations are provided to show the large adjustability of filters, including ultra wideband and narrowband filters. We fabricate a sample of the new hybrid device in the microwave frequencies, and measurement results have excellent agreements to numerical simulations, demonstrating excellent filtering characteristics such as low loss, high efficiency, and good square ratio. The proposed hybrid circuit gives important potential to accelerate the development of plasmonic integrated functional devices and circuits in both microwave and terahertz frequencies.

  6. A Framework for Six Sigma Project Selection in Higher Educational Institutions, Using a Weighted Scorecard Approach

    Science.gov (United States)

    Holmes, Monica C.; Jenicke, Lawrence O.; Hempel, Jessica L.

    2015-01-01

    Purpose: This paper discusses the importance of the Six Sigma selection process, describes a Six Sigma project in a higher educational institution and presents a weighted scorecard approach for project selection. Design/Methodology/Approach: A case study of the Six Sigma approach being used to improve student support at a university computer help…

  7. sigma54-Mediated control of the mannose phosphotransferase sytem in Lactobacillus plantarum impacts on carbohydrate metabolism

    NARCIS (Netherlands)

    Stevens, M.J.A.; Molenaar, D.; Jong, de A.; Vos, de W.M.; Kleerebezem, M.

    2010-01-01

    Sigma factors direct specific binding of the bacterial RNA polymerase to the promoter. Here we present the elucidation of the sigma(54 ) regulon in Lactobacillus plantarum. A sequence-based regulon prediction of sigma(54)-dependent promoters revealed an operon encoding a mannose phosphotransferase

  8. sigma(54)-mediated control of the mannose phosphotransferase sytem in Lactobacillus plantarum impacts on carbohydrate metabolism

    NARCIS (Netherlands)

    Stevens, Marc J. A.; Molenaar, Douwe; de Jong, Anne; De Vos, Willem M.; Kleerebezem, Michiel

    Sigma factors direct specific binding of the bacterial RNA polymerase to the promoter. Here we present the elucidation of the sigma(54) regulon in Lactobacillus plantarum. A sequence-based regulon prediction of sigma(54)-dependent promoters revealed an operon encoding a mannose phosphotransferase

  9. Robust sigma delta converters : and their application in low-power highly-digitized flexible receivers

    NARCIS (Netherlands)

    Veldhoven, van R.H.M.; Roermund, van A.H.M.

    2011-01-01

    Sigma Delta converters are a very popular choice for the A/D converter in multi-standard, mobile and cellular receivers. Key A/D converter specifications are high dynamic range, robustness, scalability, low-power and low EMI. Robust Sigma Delta Converters presents a requirement derivation of a Sigma

  10. Inhibition of tumor cell growth by Sigma1 ligand mediated translational repression

    International Nuclear Information System (INIS)

    Kim, Felix J.; Schrock, Joel M.; Spino, Christina M.; Marino, Jacqueline C.; Pasternak, Gavril W.

    2012-01-01

    Highlights: ► Sigma1 ligand treatment mediates decrease in tumor cell mass. ► Identification of a Sigma1 ligand with reversible translational repressor actions. ► Demonstration of a role for Sigma1 in cellular protein synthesis. -- Abstract: Treatment with sigma1 receptor (Sigma1) ligands can inhibit cell proliferation in vitro and tumor growth in vivo. However, the cellular pathways engaged in response to Sigma1 ligand treatment that contribute to these outcomes remain largely undefined. Here, we show that treatment with putative antagonists of Sigma1 decreases cell mass. This effect corresponds with repressed cap-dependent translation initiation in multiple breast and prostate cancer cell lines. Sigma1 antagonist treatment suppresses phosphorylation of translational regulator proteins p70S6K, S6, and 4E-BP1. RNAi-mediated knockdown of Sigma1 also results in translational repression, consistent with the effects of antagonist treatment. Sigma1 antagonist mediated translational repression and decreased cell size are both reversible. Together, these data reveal a role for Sigma1 in tumor cell protein synthesis, and demonstrate that small molecule Sigma1 ligands can be used as modulators of protein translation.

  11. Definition of the sigma(W) Regulon of Bacillus subtilis in the Absence of Stress

    NARCIS (Netherlands)

    Zweers, Jessica C.; Nicolas, Pierre; Wiegert, Thomas; van Dijl, Jan Maarten; Denham, Emma L.

    2012-01-01

    Bacteria employ extracytoplasmic function (ECF) sigma factors for their responses to environmental stresses. Despite intensive research, the molecular dissection of ECF sigma factor regulons has remained a major challenge due to overlaps in the ECF sigma factor-regulated genes and the stimuli that

  12. Intuitive Understanding of sigma Delocalization in Loose and sigma Localization in Tight Helical Conformations of an Oligosilane Chain

    Czech Academy of Sciences Publication Activity Database

    Jovanovic, M.; Antic, D.; Rooklin, D.; Bande, A.; Michl, Josef

    2017-01-01

    Roč. 12, č. 11 (2017), s. 1250-1263 ISSN 1861-4728 Institutional support: RVO:61388963 Keywords : electron delocalization * electron localization * electronic states * oligosilanes * sigma conjugation Subject RIV: CC - Organic Chemistry OBOR OECD: Organic chemistry Impact factor: 4.083, year: 2016

  13. Loop calculations in quantum-mechanical non-linear sigma models sigma models with fermions and applications to anomalies

    NARCIS (Netherlands)

    Boer, Jan de; Peeters, Bas; Skenderis, Kostas; Nieuwenhuizen, Peter van

    1995-01-01

    We construct the path integral for one-dimensional non-linear sigma models, starting from a given Hamiltonian operator and states in a Hilbert space. By explicit evaluation of the discretized propagators and vertices we find the correct Feynman rules which differ from those often assumed. These

  14. Miniaturized bandpass filter using a meandered stepped-impedance resonator with a meandered-line stub-load on a GaAs substrate.

    Science.gov (United States)

    Chuluunbaatar, Z; Wang, C; Kim, N Y

    2014-01-01

    This paper reports a compact bandpass filter with improved skirt selectivity using integrated passive device fabrication technology on a GaAs substrate. The structure of the filter consists of electromagnetically coupled meandered-line symmetric stepped-impedance resonators. The strength of the coupling between the resonators is enhanced by using a meandered-line stub-load inside the resonators to improve the selectivity and miniaturize the size of the filter. In addition, the center frequency of the filter can be flexibly controlled by varying degrees of the capacitive coupling between resonator and stub-load. To verify the proposed concept, a protocol bandpass filter with center frequency of 6.53 GHz was designed, fabricated, and measured, with a return loss and insertion loss of 39.1 dB and 1.63 dB.

  15. Miniaturized Bandpass Filter Using a Meandered Stepped-Impedance Resonator with a Meandered-Line Stub-Load on a GaAs Substrate

    Directory of Open Access Journals (Sweden)

    Z. Chuluunbaatar

    2014-01-01

    Full Text Available This paper reports a compact bandpass filter with improved skirt selectivity using integrated passive device fabrication technology on a GaAs substrate. The structure of the filter consists of electromagnetically coupled meandered-line symmetric stepped-impedance resonators. The strength of the coupling between the resonators is enhanced by using a meandered-line stub-load inside the resonators to improve the selectivity and miniaturize the size of the filter. In addition, the center frequency of the filter can be flexibly controlled by varying degrees of the capacitive coupling between resonator and stub-load. To verify the proposed concept, a protocol bandpass filter with center frequency of 6.53 GHz was designed, fabricated, and measured, with a return loss and insertion loss of 39.1 dB and 1.63 dB.

  16. High-Bandwidth, High-Efficiency Envelope Tracking Power Supply for 40W RF Power Amplifier Using Paralleled Bandpass Current Sources

    DEFF Research Database (Denmark)

    Høyerby, Mikkel Christian Wendelboe; Andersen, Michael Andreas E.

    2005-01-01

    This paper presents a high-performance power conversion scheme for power supply applications that require very high output voltage slew rates (dV/dt). The concept is to parallel 2 switching bandpass current sources, each optimized for its passband frequency space and the expected load current....... The principle is demonstrated with a power supply, designed for supplying a 40 W linear RF power amplifier for efficient amplification of a 16-QAM modulated data stream...

  17. THE SUBSTELLAR POPULATION OF {sigma} ORIONIS: A DEEP WIDE SURVEY

    Energy Technology Data Exchange (ETDEWEB)

    Bejar, V. J. S.; Rebolo, R. [Instituto de Astrofisica de Canarias, E-38205 La Laguna, Tenerife (Spain); Zapatero Osorio, M. R.; Martin, E. L. [Centro de Astrobiologia (INTA-CSIC), Crta. Ajalvir km 4, E-28850 Torrejon de Ardoz, Madrid (Spain); Caballero, J. A.; Barrado, D. [Centro de Astrobiologia (INTA-CSIC), ESAC campus, P.O. Box 78, E-28691 Villanueva de la Canada, Madrid (Spain); Mundt, R.; Bailer-Jones, C. A. L., E-mail: vbejar@iac.es, E-mail: mosorio@cab.inta-csic.es, E-mail: ege@cab.inta-csic.es, E-mail: rrl@iac.es, E-mail: caballero@cab.inta-csic.es, E-mail: barrado@cab.inta-csic.es, E-mail: mundt@mpia.de, E-mail: calj@mpia.de [Max-Planck-Institut fuer Astronomie, Koenigstuhl 17, D-69117 Heidelberg (Germany)

    2011-12-10

    We present a deep I, Z photometric survey covering a total area of 1.12 deg{sup 2} of the {sigma} Orionis cluster and reaching completeness magnitudes of I = 22 and Z = 21.5 mag. From I, I - Z color-magnitude diagrams we have selected 153 candidates that fit the previously known sequence of the cluster. They have magnitudes in the range I = 16-23 mag, which corresponds to a mass interval from 0.1 down to 0.008 M{sub Sun} at the most probable age of {sigma} Orionis (2-4 Myr). Using J-band photometry, we find that 124 of the 151 candidates within the completeness of the optical survey (82%) follow the previously known infrared photometric sequence of the cluster and are probably members. We have studied the spatial distribution of the very low mass stars and brown dwarf population of the cluster and found that there are objects located at distances greater than 30 arcmin to the north and west of {sigma} Orionis that probably belong to different populations of the Orion's Belt. For the 102 bona fide {sigma} Orionis cluster member candidates, we find that the radial surface density can be represented by a decreasing exponential function ({sigma}={sigma}{sub 0}e{sup -r/r{sub 0}}) with a central density of {sigma}{sub 0} = 0.23 {+-} 0.03 objects arcmin{sup -2} and a characteristic radius of r{sub 0} = 9.5 {+-} 0.7 arcmin. From a statistical comparison with Monte Carlo simulations, we conclude that the spatial distribution of the objects located at the same distance from the center of the cluster is compatible with a Poissonian distribution and, hence, that very low mass stars and brown dwarfs are not mainly forming aggregations or sub-clustering. Using near-infrared JHK-band data from Two Micron All Sky Survey and UKIRT Deep Infrared Sky Survey and mid-infrared data from Infrared Array Camera/Spitzer, we find that about 5%-9% of the brown dwarf candidates in the {sigma} Orionis cluster have K-band excesses and 30% {+-} 7% of them show mid-infrared excesses at

  18. A miniaturized Microwave Bandpass Filter Based on Modified (Mg0.95Ca0.05TiO3 Substrate

    Directory of Open Access Journals (Sweden)

    Hu Mingzhe

    2016-01-01

    Full Text Available A microwave miniaturized bandpass filter using (Mg0.95Ca0.05TiO3 (abbreviated as 95MCT hereafter ceramic substrate is investigated in the present paper. The paper studies the sintering and microwave dielectric properties of Al2O3, La2O3 and SiO2 co-doped 95MCT. The XRD pattern shows that a secondary phase MgTi2O5 is easily segregated in 95MCT ceramic, however, through co-doping it can be effectively suppressed, and the microwave dielectric properties, especially, the Qf value can be significantly improved. Through optimizing the co-doping ratio of Al2O3, La2O3 and SiO2, the sintering temperature of 95MCT ceramic can be lowered by 80°C, and the microwave dielectric properties can reach Qf=61856GHz and εr=19.84, which indicates the modified 95MCT ceramic have a great potential application in microwave communication devices. Based on this, we also designed a miniaturized microwave bandpass filter (BPF on modified 95MCT substrate. Through a full wave electromagnetic structure simulation, the results show that the center frequency of the BPF is 2.45GHz and the relative bandwidth is 4.09% with the insertion loss of less than 0.2dB in the whole bandpass.

  19. Six Sigma: not for the faint of heart.

    Science.gov (United States)

    Benedetto, Anthony R

    2003-01-01

    Six Sigma is an excellent quality and performance improvement tool. Like any tool, the results of using it are highly dependent on whether you use it with competence and on the right problem. This article will help you decide if your problem is well-suited for a Six Sigma approach and will suggest the optimum approach for planning and implementing Six Sigma methodology. Performance improvement methods can be grouped into two broad categories, based on the problem to be addressed. When the problem is relatively minor and localized, "evolutionary" methods may be suitable (e.g., quality circles, problem-solving staff meetings, continuous quality improvement [CQI], total quality management [TQM]). These tools work best when modest incremental improvements are sought, when major process redesign is not thought to be necessary, and when the avoidance of workplace disruption is desired. Reengineering and Six Sigma are the best-known examples of the "revolutionary" performance improvement methods. These methods should be used when major (drastic, do or die, etc.) improvements are needed. Problems that cross departmental boundaries need these methods. When a process is so dysfunctional that you feel like you need to tear up the standard operating procedure (SOP) and start all over again, you need a revolutionary method. A Six Sigma project requires a major expenditure of money and employee time, and a willingness to make some hard decisions about jobs, employee retention and relationships among stakeholders. An institution's culture should be considered as part of the decision about using Six Sigma. If the institution has a history of making data-driven decisions, or at least has displayed openness to operating in that manner, Six Sigma has a good chance of success. A radiology-driven Six Sigma project should not be undertaken until a comprehensive written description of the scope of the project is approved by the radiology department leadership team and by the appropriate

  20. Ab initio calculation of the electronic structures of the (7)Sigma+ ground and A (7)Pi and a (5)Sigma+ excited states of MnH.

    Science.gov (United States)

    Tomonari, Mutsumi; Nagashima, Umpei; Hirano, Tsuneo

    2009-04-21

    Electronic structures and molecular constants of the ground (7)Sigma(+) and low-lying A (7)Pi and a (5)Sigma(+) electronic excited states of the MnH molecule were studied by multireference single and double excitation configuration interaction (MR-SDCI) with Davidson's correction (+Q) calculations under exact C(infinity v) symmetry using Slater-type basis sets. To correctly describe the (7)Sigma(+) electronic ground state, X (7)Sigma(+), at the MR-SDCI+Q calculation, we employed a large number of reference configurations in terms of the state-averaged complete active space self-consistent field (CASSCF) orbitals, taking into account the contribution from the B (7)Sigma(+) excited state. The A (7)Pi and a (5)Sigma(+) states can well be described by the MR-SDCI wave functions based on the CASSCF orbitals obtained for the lowest state only. In the MR-SDCI+Q, calculations of the X (7)Sigma(+), A (7)Pi, and a (5)Sigma(+) states required 16, 7, and 17 reference configurations, respectively. Molecular constants, i.e., r(e) and omega(e) of these states and excitation energy from the X (7)Sigma(+) state, obtained at the MR-SDCI+Q level, showed a good agreement with experimental values. The small remaining differences may be accounted for by taking relativistic effects into account.

  1. Production of n-bar's and Sigma-bar+-'s in e+e- annihilations

    International Nuclear Information System (INIS)

    Ferguson, T.; Buchanan, C.; Nodulman, L.; Poster, R.; Breidenbach, M.; Morehouse, C.C.; Vannucci, F.

    1979-01-01

    The production of antineutrons and charged Sigma-bar's in e + e - annihilations has been measured at √s +- production between 4 and 7 GeV is consistent with simple expectations for charmed-baryon production. A search for the decays Lambda-bar - /sub c/ → Sigma-bar +- π -+ π - and Sigma-baratsup asteriskat/sub c//Sigma-bar/sub c/ → Lambda-bar - /sub c/π +- yields no significant peaks. An upper limit, at the 90% confidence level, of sigmaatsub Lambda-baratc-italicB (Lambda-bar/sub c/ → Sigma-bar +- π -+ π - ) < 56 pb is set

  2. High-power circulator test results at 350 and 700 MHz

    International Nuclear Information System (INIS)

    Roybal, W.; Bradley, J.T.; Rees, D.E.

    2000-01-01

    The high-power RF systems for the Accelerator Production of Tritium (APT) program require high-power circulators at 350 MHz and 700 MHz to protect 1 MW Continuous Wave (CW) klystrons from reflected power. The 350 MHz circulator is based on the CERN, EXF, and APS designs and has performed very well. The 700 MHz circulator is a new design. Prototype 700 MHz circulators have been high-power tested at Los Alamos National Laboratory (LANL). The first of these circulators has satisfied performance requirements. The circulator requirements, results from the testing, and lessons learned from this development are presented and discussed

  3. Two-dimensional 220 MHz Fourier transform EPR imaging

    International Nuclear Information System (INIS)

    Placidi, Giuseppe; Brivati, John A.; Alecci, Marcello; Testa, Luca; Sotgiu, Antonello

    1998-01-01

    In the last decade radiofrequency continuous-wave EPR spectrometers have been developed to detect and localize free radicals in vivo. Only recently, pulsed radiofrequency EPR spectrometers have been described for imaging applications with small samples. In the present work, we show the first two-dimensional image obtained at 220 MHz on a large phantom (40 ml) that simulates typical conditions of in vivo EPR imaging. This pulsed EPR apparatus has the potential to make the time required for three-dimensional imaging compatible with the biological half-life of normally used paramagnetic probes. (author)

  4. Operation of a 473 MHz four-rod cavity RFQ

    International Nuclear Information System (INIS)

    Kazimi, R.; Huson, F.R.; Mackay, W.W.; Meitzler, C.R.

    1992-01-01

    We have constructed a new type of four-rod Radio Frequency Quadrupole to operate at 473 MHz. Four-rod structures have not previously been built for such a high frequency. The RFQ is designed to accelerate 10 mA of H - ions from 30 keV to 0.5 MeV. The rf measurements and beam test of the RFQ have been performed successfully. Here we present operational results of the RFQ system including measurements of the beam current, the required rf power, energy, energy spread, and emittance. (Author) 8 refs., 6 figs., 2 tabs

  5. LAMPF 201.25-MHz linac field distribution

    International Nuclear Information System (INIS)

    Jameson, R.A.; Halbig, J.K.

    1978-01-01

    Returning of the 201.25-MHz accelerator structure field distributions after the 1975 shutdown is described, and final data are given for use in beam dynamics studies. Several improvements made in procedures included a different method for stopband closure check and a positive method for postcoupler clamping. To obtain accurate results for the first tank a rigorous data reduction technique that included the removal of a ''signature'' due to the bead-pull string itself was used. Other special studies are reported, including the effects of vacuum, bead size, slug tuners, and a bead-pull method for measuring the cavity quality factor Q

  6. BNL 56 MHz HOM Damper Prototype Fabrication at JLab

    Energy Technology Data Exchange (ETDEWEB)

    Huque, Naeem A. [Jefferson Lab., Newport News, VA (United States); Daly, Edward F. [Jefferson Lab., Newport News, VA (United States); Clemens, William A. [Jefferson Lab., Newport News, VA (United States); McIntyre, Gary T. [Brookhaven National Lab. (BNL), Upton, NY (United States); Wu, Qiong [Brookhaven National Lab. (BNL), Upton, NY (United States); Seberg, Scott [Brookhaven National Lab. (BNL), Upton, NY (United States); Bellavia, Steve [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2015-09-01

    A prototype Higher-Order Mode (HOM) Damper was fabricated at JLab for the Relativistic Heavy-Ion Collider's (RHIC) 56 MHz cavity at Brookhaven National Laboratory (BNL). Primarily constructed from high RRR Niobium and Sapphire, the coaxial damper presented significant challenges in electron-beam welding (EBW), brazing and machining via acid etching. The results of the prototype operation brought about changes in the damper design, due to overheating braze alloys and possible multi-pacting. Five production HOM dampers are currently being fabricated at JLab. This paper outlines the challenges faced in the fabrication process, and the solutions put in place.

  7. Effects of 415 MHz frequency on human lymphocyte genome

    International Nuclear Information System (INIS)

    Garaj-Vrhovac, V.; Fucic, A.; Kubelka, D.; Vojvodic, S.

    1996-01-01

    The continuously increasing use of artificial sources of electromagnetic radiation in industry and medicine has been accompanied in everyday life with telecommunication systems which is followed with great interest in possible hazardous effects of this type of radiation. The interesting applications of mobile telecommunications and the use of cellular phones are of topic interest. Numerous cytogenetic investigations are focused on the effects of microwave radiation from mobile communications frequency of 450 and 950 MHz on isolated cells in vitro. The aim of this work was to investigate the effects of microwaves from mobile telephone frequencies on human peripheral blood lymphocytes cultured in vitro. (author)

  8. Measure of enzymatic activity coincident with 2450 MHz microwave exposure

    Energy Technology Data Exchange (ETDEWEB)

    Ward, T R; Allis, J W; Elder, J A

    1975-09-01

    Enzyme preparations were exposed to microwave radiation at 2450 MHz and enzymatic activity was simultaneously monitored spectrophotometrically with a crossed-beam exposure detection system. Enzymes studied were glucose 6-phosphate dehydrogenase from human red blood cells and yeast, adenylate kinase from rat liver mitochondria and rabbit muscle, and rat liver microsomal NADPH cytochrome c reductase. No difference was found between the specific activity at 25/sup 0/C of unirradiated controls and enzyme preparations irradiated at an absorbed dose rate of 42 W/kg.

  9. Controls and interlocks for a prototype 1MHz beam chopper

    International Nuclear Information System (INIS)

    Waters, G.; Bishop, D.; Barnes, M.J.; Wait, G.D.

    1991-05-01

    A prototype 1 MHz beam chopper for the proposed KAON Factory at TRIUMF has been constructed. The chopper is an electric field device, driven by a tetrode based pulser, for deflecting a charged particle beam. Associated with the tetrode used in the prototype design are high voltage power supplies for the electrodes. We use an FET based grid pulser and a sequencer capable of accurate digital control of pulse timing to 0.4 ns. A safety interlock and control system using a programmable controller with fibre optic links has been built. This has given us the versatility required in a prototype system. (Author) 4 refs., 5 figs

  10. MHz gravitational waves from short-term anisotropic inflation

    International Nuclear Information System (INIS)

    Ito, Asuka; Soda, Jiro

    2016-01-01

    We reveal the universality of short-term anisotropic inflation. As a demonstration, we study inflation with an exponential type gauge kinetic function which is ubiquitous in models obtained by dimensional reduction from higher dimensional fundamental theory. It turns out that an anisotropic inflation universally takes place in the later stage of conventional inflation. Remarkably, we find that primordial gravitational waves with a peak amplitude around 10 −26 ∼10 −27 are copiously produced in high-frequency bands 10 MHz∼100 MHz. If we could detect such gravitational waves in future, we would be able to probe higher dimensional fundamental theory.

  11. Brightness distribution data on 2918 radio sources at 365 MHz

    International Nuclear Information System (INIS)

    Cotton, W.D.; Owen, F.N.; Ghigo, F.D.

    1975-01-01

    This paper is the second in a series describing the results of a program attempting to fit models of the brightness distribution to radio sources observed at 365 MHz with the Bandwidth Synthesis Interferometer (BSI) operated by the University of Texas Radio Astronomy Observatory. Results for a further 2918 radio sources are given. An unresolved model and three symmetric extended models with angular sizes in the range 10--70 arcsec were attempted for each radio source. In addition, for 348 sources for which other observations of brightness distribution are published, the reference to the observations and a brief description are included

  12. U and Pu Gamma-Ray Measurements of Spent Fuel Using a Gamma-Ray Mirror Band-Pass Filter

    International Nuclear Information System (INIS)

    Ziock, K.-P.; Kisner, R.; Melin, A.; Patton, B.; Alameda, J.; Brejnhold, N.; Decker, T.; Descalle, M.-A.; Fernandez-Perea, M.; Hill, R.; Ruz Armendariz, J.; Soufli, R.

    2015-01-01

    We report the use of grazing incidence gamma-ray mirrors as narrow band-pass filters for advanced non-destructive analysis of spent nuclear fuel. The mirrors limit radiation reaching an HPGe detector to narrow spectral bands around characteristic emission lines from fissile isotopes in the fuel. Ideally, these emissions could be used to determine the fuel's fissile content, but they are normally masked by the overwhelming radiation emitted by short-lived fission by-products. These latter emissions raise the overall background, making direct observation of the fuel with HPGe detectors virtually impossible. Such observations can only be performed using precise collimators that restrict the detector's field of view to very small solid angles. This results in impracticably long dwell times for safeguards measurements targeting the weak isotopic lines of interest. In a proof-ofconcept experiment, a set of simple flat gamma-ray mirrors was used to observe the atomic florescence lines from U and Pu from a spent nuclear fuel pin. For the measurements, the mirrors were placed at the egress of an access port in a hot cell wall. A coarse collimator in the port restricted radiation from a fuel pin placed in front of the port to fully illuminate the front surface of the mirror assembly (0:5 x 3:8 cm2). The mirrors, consisting of highly polished silicon substrates deposited with WC/SiC multilayer coatings, were successfully used to deflect the lines of interest onto an HPGe detector while the intense primary radiation from the spent fuel was blocked by a lead beam stop. The gamma-ray mirror multilayer coatings used here at ∼100 keV, have been experimentally tested at energies as high as 645 keV, indicating that direct observation of nuclear emission lines from 239Pu should be possible with an appropriately designed optic. (author)

  13. Robust detection of heart beats in multimodal records using slope- and peak-sensitive band-pass filters.

    Science.gov (United States)

    Pangerc, Urška; Jager, Franc

    2015-08-01

    In this work, we present the development, architecture and evaluation of a new and robust heart beat detector in multimodal records. The detector uses electrocardiogram (ECG) signals, and/or pulsatile (P) signals, such as: blood pressure, artery blood pressure and pulmonary artery pressure, if present. The base approach behind the architecture of the detector is collecting signal energy (differentiating and low-pass filtering, squaring, integrating). To calculate the detection and noise functions, simple and fast slope- and peak-sensitive band-pass digital filters were designed. By using morphological smoothing, the detection functions were further improved and noise intervals were estimated. The detector looks for possible pacemaker heart rate patterns and repairs the ECG signals and detection functions. Heart beats are detected in each of the ECG and P signals in two steps: a repetitive learning phase and a follow-up detecting phase. The detected heart beat positions from the ECG signals are merged into a single stream of detected ECG heart beat positions. The merged ECG heart beat positions and detected heart beat positions from the P signals are verified for their regularity regarding the expected heart rate. The detected heart beat positions of a P signal with the best match to the merged ECG heart beat positions are selected for mapping into the noise and no-signal intervals of the record. The overall evaluation scores in terms of average sensitivity and positive predictive values obtained on databases that are freely available on the Physionet website were as follows: the MIT-BIH Arrhythmia database (99.91%), the MGH/MF Waveform database (95.14%), the augmented training set of the follow-up phase of the PhysioNet/Computing in Cardiology Challenge 2014 (97.67%), and the Challenge test set (93.64%).

  14. Dual-Mode Dual-Band Microstrip Bandpass Filter Based on Fourth Iteration T-Square Fractal and Shorting Pin

    Directory of Open Access Journals (Sweden)

    E. S. Ahmed

    2012-06-01

    Full Text Available A new class of dual mode microstrip fractal resonator is proposed and developed for miniaturization of the dual band bandpass filter. The perimeter of the proposed resonator is increased by employing fourth iteration T-square fractal shape. Consequently the lower resonant frequency of the filter is decreased without increasing the usable space. The self similarity of the usable structure enables it to produce the two degenerate modes which are coupled using the proper perturbation technique. The shorting pin is placed at the null in the surface current distribution at the center of the resonator. This shorting pin is coactively coupled to the resonant circuit of the resonator, effectively coupled to the lower degenerate mode and reduces the lower edge band resonant frequency. By adjusting the resonator dimensions and the size of the shorting pin, the resonant frequency and the out-of-band rejection around the transmission bands can be controlled to meet the design requirements. The simulated response of the designed filter has two transmission bands, the first band is from 2.34-3.65 GHz with resonant frequencies at 2.47GHz and 3.55GHz, the second band is from 4.37-5.324GHz with resonant frequencies at 4.5GHz and 5.13GHz. In the pass bands, the group delay is less than 0.65 ns. The proposed filter can be applied to WLAN (2.4 GHz and 5.2 GHz and WiMAX (3.5 GHz and Bluetooth and ZigBee (4.9 GHz.

  15. IMPROVE MACHINING PROCESS CAPABILITY BY USING SIX-SIGMA

    Directory of Open Access Journals (Sweden)

    Sanjit Ray

    2011-06-01

    Full Text Available Abstract: Six-Sigma is an improvement strategy for achieving customer satisfaction by reducing variation and thus producing products and services better, faster and cheaper. This study presents a Six-Sigma project of an automotive plant illustrating how the DMAIC methodology and statistical techniques were applied to resolve the issue of manufacturing process capability. This project has substantially benefit ted the organization by reducing the variation of bore size of crank case, achieving zero rejection and improving the on time delivery. By using appropriate qualitative and quantitative tools in different phases of the DMAIC methodology, the critical output, key process inputs and root causes were identified, analyzed and validated. This project methodology can be used in general to reduce process variation for any other manufacturing processes as well, which will help in improving customer satisfaction.

  16. Generalized complex geometry, generalized branes and the Hitchin sigma model

    International Nuclear Information System (INIS)

    Zucchini, Roberto

    2005-01-01

    Hitchin's generalized complex geometry has been shown to be relevant in compactifications of superstring theory with fluxes and is expected to lead to a deeper understanding of mirror symmetry. Gualtieri's notion of generalized complex submanifold seems to be a natural candidate for the description of branes in this context. Recently, we introduced a Batalin-Vilkovisky field theoretic realization of generalized complex geometry, the Hitchin sigma model, extending the well known Poisson sigma model. In this paper, exploiting Gualtieri's formalism, we incorporate branes into the model. A detailed study of the boundary conditions obeyed by the world sheet fields is provided. Finally, it is found that, when branes are present, the classical Batalin-Vilkovisky cohomology contains an extra sector that is related non trivially to a novel cohomology associated with the branes as generalized complex submanifolds. (author)

  17. Sv-map between type I and heterotic sigma models

    Science.gov (United States)

    Fan, Wei; Fotopoulos, A.; Stieberger, S.; Taylor, T. R.

    2018-05-01

    The scattering amplitudes of gauge bosons in heterotic and open superstring theories are related by the single-valued projection which yields heterotic amplitudes by selecting a subset of multiple zeta value coefficients in the α‧ (string tension parameter) expansion of open string amplitudes. In the present work, we argue that this relation holds also at the level of low-energy expansions (or individual Feynman diagrams) of the respective effective actions, by investigating the beta functions of two-dimensional sigma models describing world-sheets of open and heterotic strings. We analyze the sigma model Feynman diagrams generating identical effective action terms in both theories and show that the heterotic coefficients are given by the single-valued projection of the open ones. The single-valued projection appears as a result of summing over all radial orderings of heterotic vertices on the complex plane representing string world-sheet.

  18. T^{\\sigma}_{\\rho}(G) Theories and Their Hilbert Series

    CERN Document Server

    Cremonesi, Stefano; Mekareeya, Noppadol; Zaffaroni, Alberto

    2015-01-01

    We give an explicit formula for the Higgs and Coulomb branch Hilbert series for the class of 3d N=4 superconformal gauge theories T^{\\sigma}_{\\rho}(G) corresponding to a set of D3 branes ending on NS5 and D5-branes, with or without O3 planes. Here G is a classical group, \\sigma is a partition of G and \\rho a partition of the dual group G^\\vee. In deriving such a formula we make use of the recently discovered formula for the Hilbert series of the quantum Coulomb branch of N=4 superconformal theories. The result can be expressed in terms of a generalization of a class of symmetric functions, the Hall-Littlewood polynomials, and can be interpreted in mathematical language in terms of localization. We mainly consider the case G=SU(N) but some interesting results are also given for orthogonal and symplectic groups.

  19. Six sigma for organizational excellence a statistical approach

    CERN Document Server

    Muralidharan, K

    2015-01-01

    This book discusses the integrated concepts of statistical quality engineering and management tools. It will help readers to understand and apply the concepts of quality through project management and technical analysis, using statistical methods. Prepared in a ready-to-use form, the text will equip practitioners to implement the Six Sigma principles in projects. The concepts discussed are all critically assessed and explained, allowing them to be practically applied in managerial decision-making, and in each chapter, the objectives and connections to the rest of the work are clearly illustrated. To aid in understanding, the book includes a wealth of tables, graphs, descriptions and checklists, as well as charts and plots, worked-out examples and exercises. Perhaps the most unique feature of the book is its approach, using statistical tools, to explain the science behind Six Sigma project management and integrated in engineering concepts. The material on quality engineering and statistical management tools of...

  20. The coupling of Poisson sigma models to topological backgrounds

    Energy Technology Data Exchange (ETDEWEB)

    Rosa, Dario [School of Physics, Korea Institute for Advanced Study,Seoul 02455 (Korea, Republic of)

    2016-12-13

    We extend the coupling to the topological backgrounds, recently worked out for the 2-dimensional BF-model, to the most general Poisson sigma models. The coupling involves the choice of a Casimir function on the target manifold and modifies the BRST transformations. This in turn induces a change in the BRST cohomology of the resulting theory. The observables of the coupled theory are analyzed and their geometrical interpretation is given. We finally couple the theory to 2-dimensional topological gravity: this is the first step to study a topological string theory in propagation on a Poisson manifold. As an application, we show that the gauge-fixed vectorial supersymmetry of the Poisson sigma models has a natural explanation in terms of the theory coupled to topological gravity.

  1. LEAN AND SIX SIGMA CONCEPTS APPLICATION IN PHARMACEUTICAL INDUSTRY

    Directory of Open Access Journals (Sweden)

    Katarina Pavlović

    2012-03-01

    Full Text Available LEAN thinking and Six Sigma have been utilized by manufacturing industries to decrease cost and improve quality and productivity by reducing variation and production defects [1]. Because of the dramatic successes in manufacturing, there is rising interest among companies in the pharmaceutical industry, which chooses to implement LEAN in order to accomplish such goals as decreased wait time to release product to the market, reduce production waste, and improve communication with end users and raize quality level both in the production and in testing laboratories. In this article, basics of LEAN and Six Sigma are presented and suggestion was given for application of their concepts in pharmaceutical industry together with harmonization with legal regulation represented by requirements Good Manufacturing Practice (cGMP, in order to work "smarter", more cost-effectively and avoid was ting time and other resources.

  2. LEAN AND SIX SIGMA CONCEPTS - APPLICATION IN PHARMACEUTICAL INDUSTRY

    Directory of Open Access Journals (Sweden)

    Katarina Pavlović

    2011-06-01

    Full Text Available LEAN thinking and Six Sigma have been utilized by manufacturing industries to decrease cost and improve quality and productivity by reducing variation and production defects. Because of the dramatic successes in manufacturing, there is rising interest among companies in the pharmaceutical industry, which choose to implement LEAN in order to accomplish such goals as decreased wait time to release product to the market, reduce production waste, improve communication with end users and raise quality level both in the production and in testing laboratories. In this article, basics of LEAN and Six Sigma are presented and suggestion was given for application of their concepts in pharmaceutical industry together with harmonization with legal regulation represented by requirements Good Manufacturing Practice (cGMP, in order to work "smarter", more cost- effectively and avoid wasting time and other resources.

  3. Pseudo-random number generator for the Sigma 5 computer

    Science.gov (United States)

    Carroll, S. N.

    1983-01-01

    A technique is presented for developing a pseudo-random number generator based on the linear congruential form. The two numbers used for the generator are a prime number and a corresponding primitive root, where the prime is the largest prime number that can be accurately represented on a particular computer. The primitive root is selected by applying Marsaglia's lattice test. The technique presented was applied to write a random number program for the Sigma 5 computer. The new program, named S:RANDOM1, is judged to be superior to the older program named S:RANDOM. For applications requiring several independent random number generators, a table is included showing several acceptable primitive roots. The technique and programs described can be applied to any computer having word length different from that of the Sigma 5.

  4. Multi-Agent Modeling in Managing Six Sigma Projects

    Directory of Open Access Journals (Sweden)

    K. Y. Chau

    2009-10-01

    Full Text Available In this paper, a multi-agent model is proposed for considering the human resources factor in decision making in relation to the six sigma project. The proposed multi-agent system is expected to increase the acccuracy of project prioritization and to stabilize the human resources service level. A simulation of the proposed multiagent model is conducted. The results show that a multi-agent model which takes into consideration human resources when making decisions about project selection and project team formation is important in enabling efficient and effective project management. The multi-agent modeling approach provides an alternative approach for improving communication and the autonomy of six sigma projects in business organizations.

  5. Brane solutions of a spherical sigma model in six dimensions

    International Nuclear Information System (INIS)

    Lee, Hyun Min; Papazoglou, Antonios

    2005-01-01

    We explore solutions of six-dimensional gravity coupled to a non-linear sigma model, in the presence of codimension-two branes. We investigate the compactifications induced by a spherical scalar manifold and analyze the conditions under which they are of finite volume and singularity free. We discuss the issue of single-valuedness of the scalar fields and provide some special embedding of the scalar manifold to the internal space which solves this problem. These brane solutions furnish some self-tuning features, however they do not provide a satisfactory explanation of the vanishing of the effective four-dimensional cosmological constant. We discuss the properties of this model in relation with the self-tuning example based on a hyperbolic sigma model

  6. Rethinking behavioral health processes by using design for six sigma.

    Science.gov (United States)

    Lucas, Anthony G; Primus, Kelly; Kovach, Jamison V; Fredendall, Lawrence D

    2015-02-01

    Clinical evidence-based practices are strongly encouraged and commonly utilized in the behavioral health community. However, evidence-based practices that are related to quality improvement processes, such as Design for Six Sigma, are often not used in behavioral health care. This column describes the unique partnership formed between a behavioral health care provider in the greater Pittsburgh area, a nonprofit oversight and monitoring agency for behavioral health services, and academic researchers. The authors detail how the partnership used the multistep process outlined in Design for Six Sigma to completely redesign the provider's intake process. Implementation of the redesigned process increased access to care, decreased bad debt and uncollected funds, and improved cash flow--while consumer satisfaction remained high.

  7. Lean six sigma implementation in a yarn textile industry

    Directory of Open Access Journals (Sweden)

    Rayra Rodrigues Nogueira

    2017-06-01

    Full Text Available Due to fierce competition from companies in achieving larger market share, there is an increasing interest regarding cost reduction, efficiency in business and processes, increase in quality and continuous improvement. Given these situations, companies are adopting some practices which seek to improve their strategies, increase understanding of the needs of their customers and promote business growth, the Lean Manufacturing and Six Sigma programs were adopted in order to enable businesses to succeed in achieving continuous improvement in their business. This paper presents a case study of a textile yarn industry which, in order to increase the sales of the business and the elimination of waste, used the methodology of Lean Six Sigma Program based on DMAIC method to assist in achieving these goals.

  8. Applying a Hybrid MCDM Model for Six Sigma Project Selection

    Directory of Open Access Journals (Sweden)

    Fu-Kwun Wang

    2014-01-01

    Full Text Available Six Sigma is a project-driven methodology; the projects that provide the maximum financial benefits and other impacts to the organization must be prioritized. Project selection (PS is a type of multiple criteria decision making (MCDM problem. In this study, we present a hybrid MCDM model combining the decision-making trial and evaluation laboratory (DEMATEL technique, analytic network process (ANP, and the VIKOR method to evaluate and improve Six Sigma projects for reducing performance gaps in each criterion and dimension. We consider the film printing industry of Taiwan as an empirical case. The results show that our study not only can use the best project selection, but can also be used to analyze the gaps between existing performance values and aspiration levels for improving the gaps in each dimension and criterion based on the influential network relation map.

  9. Low-energy limit of the extended Linear Sigma Model

    Energy Technology Data Exchange (ETDEWEB)

    Divotgey, Florian [Johann Wolfgang Goethe-Universitaet, Institut fuer Theoretische Physik, Frankfurt am Main (Germany); Kovacs, Peter [Wigner Research Center for Physics, Hungarian Academy of Sciences, Institute for Particle and Nuclear Physics, Budapest (Hungary); GSI Helmholtzzentrum fuer Schwerionenforschung, ExtreMe Matter Institute, Darmstadt (Germany); Giacosa, Francesco [Johann Wolfgang Goethe-Universitaet, Institut fuer Theoretische Physik, Frankfurt am Main (Germany); Jan-Kochanowski University, Institute of Physics, Kielce (Poland); Rischke, Dirk H. [Johann Wolfgang Goethe-Universitaet, Institut fuer Theoretische Physik, Frankfurt am Main (Germany); University of Science and Technology of China, Interdisciplinary Center for Theoretical Study and Department of Modern Physics, Hefei, Anhui (China)

    2018-01-15

    The extended Linear Sigma Model is an effective hadronic model based on the linear realization of chiral symmetry SU(N{sub f}){sub L} x SU(N{sub f}){sub R}, with (pseudo)scalar and (axial-)vector mesons as degrees of freedom. In this paper, we study the low-energy limit of the extended Linear Sigma Model (eLSM) for N{sub f} = flavors by integrating out all fields except for the pions, the (pseudo-)Nambu-Goldstone bosons of chiral symmetry breaking. The resulting low-energy effective action is identical to Chiral Perturbation Theory (ChPT) after choosing a representative for the coset space generated by chiral symmetry breaking and expanding it in powers of (derivatives of) the pion fields. The tree-level values of the coupling constants of the effective low-energy action agree remarkably well with those of ChPT. (orig.)

  10. Ward Identity and Scattering Amplitudes for Nonlinear Sigma Models

    Science.gov (United States)

    Low, Ian; Yin, Zhewei

    2018-02-01

    We present a Ward identity for nonlinear sigma models using generalized nonlinear shift symmetries, without introducing current algebra or coset space. The Ward identity constrains correlation functions of the sigma model such that the Adler's zero is guaranteed for S -matrix elements, and gives rise to a subleading single soft theorem that is valid at the quantum level and to all orders in the Goldstone decay constant. For tree amplitudes, the Ward identity leads to a novel Berends-Giele recursion relation as well as an explicit form of the subleading single soft factor. Furthermore, interactions of the cubic biadjoint scalar theory associated with the single soft limit, which was previously discovered using the Cachazo-He-Yuan representation of tree amplitudes, can be seen to emerge from matrix elements of conserved currents corresponding to the generalized shift symmetry.

  11. DEPLOYMENT OF SIX SIGMA METHODOLOGY IN PHACOEMULSIFICATION CATARACT SURGERY

    Directory of Open Access Journals (Sweden)

    Ibrahim SAHBAZ

    2014-04-01

    Full Text Available The purpose of this study is to show how a public eye care center in Turkey initiated Six Sigma principles to reduce the number of complications encountered during and after phacoemulsification cataract surgeries. To analyze the 3-year data, main tools of Six Sigma’s Define-Measure-Analyze-Improve-Control (DMAIC improvement cycle such as SIPOC table, Fishbone Diagram and, Failure, Mode and Effect Analysis were implemented. Experience of the ophthalmic surgeon, patient’s anatomy, cooperation of patient during the surgery, sterilization and hygiene, attention of assistant surgeon, calibration of equipment and quality/chemical composition of intraocular material were identified to be Critical-to-Quality (CTQ factors for a successful phacoemulsification cataract surgery. The most frequently occurring complication was found to be iris atrophy. The process sigma level for the process was found to be 3.958.

  12. DEVELOPMENT OF SIX SIGMA INFRASTRUCTURE FOR STRABISMUS SURGERIES

    Directory of Open Access Journals (Sweden)

    Mehmet Tolga Taner

    2014-01-01

    Full Text Available The purpose of this study is to show how a private eye care center in Turkey developed a Six Sigma infrastructure to investigate the root causes of complications occuring during strabismus surgeries. To analyze the collected data, main tools of Six Sigma’s Define-Measure-Analyze-Improve-Control (DMAIC improvement cycle such as SIPOC table, Fishbone Diagram and, Failure, Mode and Effect Analysis were implemented. Patient’s eye anatomy, experience of the anesthesiologist, experience/attention of the strabismus surgeon was identified to be Critical-to-Quality (CTQ factors for a successful strabismus surgery. The most frequent complications of strabismus surgeries were found to be X, Y and Z. The process sigma level was found to be 3.2025.

  13. 47 CFR 90.259 - Assignment and use of frequencies in the bands 216-220 MHz and 1427-1432 MHz.

    Science.gov (United States)

    2010-10-01

    ... MHz band are secondary to the Wireless Medical Telemetry Service except in the locations specified in... operations are secondary to the Wireless Medical Telemetry Service in the 1429-1431.5 MHz band. (3) All... 47 Telecommunication 5 2010-10-01 2010-10-01 false Assignment and use of frequencies in the bands...

  14. 47 CFR 101.82 - Reimbursement and relocation expenses in the 2110-2150 MHz and 2160-2200 MHz bands.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Reimbursement and relocation expenses in the... License Transfers, Modifications, Conditions and Forfeitures § 101.82 Reimbursement and relocation expenses in the 2110-2150 MHz and 2160-2200 MHz bands. (a) Reimbursement and relocation expenses for the...

  15. Geometry of surfaces associated to Grassmannian sigma models

    International Nuclear Information System (INIS)

    Delisle, L; Hussin, V; Zakrzewski, W J

    2015-01-01

    We investigate the geometric characteristics of constant Gaussian curvature surfaces obtained from solutions of the G(m, n) sigma model. Most of these solutions are related to the Veronese sequence. We show that we can distinguish surfaces with the same Gaussian curvature using additional quantities like the topological charge and the mean curvature. The cases of G(1,n) = CP n-1 and G(2,n) are used to illustrate these characteristics. (paper)

  16. Sigma models with purely Wess-Zumino-Witten actions

    International Nuclear Information System (INIS)

    Floreanini, R.; Percacci, R.; Sezgin, E.

    1988-11-01

    We study the dynamics of sigma models in arbitrary dimensions with purely Wess-Zumino-Witten actions (i.e. without kinetic terms), both from the Lagrangian and Hamiltonian point of view. These models have nontrivial gauge groups which contain the diffeomorphisms of space-time, as well as symmetry groups which in many cases turn out to be infinite dimensional. We give examples in 1,2,3 and 4 space-time dimensions.(author). 9 refs

  17. Superfield Lax formalism of supersymmetric sigma model on symmetric spaces

    International Nuclear Information System (INIS)

    Saleem, U.; Hassan, M.

    2006-01-01

    We present a superfield Lax formalism of the superspace sigma model based on the target space G/H and show that a one-parameter family of flat superfield connections exists if the target space G/H is a symmetric space. The formalism has been related to the existence of an infinite family of local and non-local superfield conserved quantities. A few examples have been given to illustrate the results. (orig.)

  18. Does the {sigma}(1580)((3)/(2)){sup -} resonance exist?

    Energy Technology Data Exchange (ETDEWEB)

    Olmsted, J.; Prakhov, S.; Manley, D.M.; Allgower, C.E.; Bekrenev, V.S.; Briscoe, W.J.; Clajus, M.; Comfort, J.R.; Craig, K.; Grosnick, D.; Isenhower, D.; Knecht, N.; Koetke, D.D.; Kozlenko, N.G.; Kruglov, S.; Kulbardis, A.A.; Lolos, G.; Lopatin, I.V.; Manweiler, R.; Marusic, A.; McDonald, S.; Nefkens, B.M.K.; Papandreou, Z.; Peaslee, D.C.; Phaisangittisakul, N.; Price, J.W.; Ramirez, A.F.; Sadler, M.; Shafi, A.; Spinka, H.; Stanislaus, T.D.S.; Starostin, A.; Staudenmaier, H.M.; Strakovsky, I.I.; Supek, I.; Tippens, W.B

    2004-05-20

    Precise new data for the reaction K{sup -}p{yields}{pi}{sup 0}{lambda} are presented in the c.m. energy range 1565 to 1600 MeV. Our analysis of these data sheds new light on claims for the {sigma}(1580)((3)/(2)){sup -} resonance, which (if it exists with the specified quantum numbers) must be an exotic baryon because of its very low mass. Our results show no evidence for this state.

  19. A community hospital's journey into Lean Six Sigma.

    Science.gov (United States)

    Stuenkel, Kurt; Faulkner, Taunya

    2009-01-01

    The implementation of Lean Six Sigma and 100-day workouts throughout the 304-bed Floyd Medical Center community hospital organization has led to sustainable results and a marked change in culture. The organization-wide learning of such an effort is deep and intehse, and to remain focused and successful it must be a priority of top management. The workout methodology can assist the organization to carry projects to completion and to achieve rapid implementation of desired improvements.

  20. Identification of sigma and chi phases in duplex stainless steels

    Energy Technology Data Exchange (ETDEWEB)

    Llorca-Isern, Núria, E-mail: nullorca@ub.edu [Departament de Ciència dels Materials i Enginyeria Metallurgica, Facultat de Química, Universitat de Barcelona, Marti-Franqués 1, 08028 Barcelona (Spain); López-Luque, Héctor, E-mail: hlopezlu7@alumnes.ub.edu [Departament de Ciència dels Materials i Enginyeria Metallurgica, Facultat de Química, Universitat de Barcelona, Marti-Franqués 1, 08028 Barcelona (Spain); López-Jiménez, Isabel, E-mail: ilopezji9@alumnes.ub.edu [Departament de Ciència dels Materials i Enginyeria Metallurgica, Facultat de Química, Universitat de Barcelona, Marti-Franqués 1, 08028 Barcelona (Spain); Biezma, Maria Victoria, E-mail: maria.biezma@unican.es [Department of Earth, Materials Science and Engineering, University of Cantabria - UC, Gamazo, 1, 39004 Santander (Spain)

    2016-02-15

    The aim of this work is to find out the most suitable method for detecting and analyzing accurately the formation conditions of secondary phases, particularly Sigma-phase (σ-phase) and Chi-phase (χ-phase) in duplex stainless steels (UNS S32205 and UNS S32750). The microstructure was characterized after a solution annealing at 1080 °C followed by an isothermal heating at 830 °C for different time ranges, ranging from 1 min to 9 h, in order to enlighten the controversial point concerning the mechanism of χ-phase nucleation in relation with the σ-phase. Etched samples were observed using optical microscopy (MO), and scanning electron microscopy (FESEM) with a backscattered electron detector (BSE) was used on unetched samples. Compositional microanalysis (EDS) was carried out for identifying the different phases present in the steels. Sigma phase was easily observed using different etching procedures, whereas χ-phase was only clearly detected with FESEM–BSE on unetched samples. The compositional analyses showed that the molybdenum content in χ-phase almost doubles the content of this element in σ-phase, and as a result the kinetics of nucleation and growth were also found to be remarkably faster when the alloy content in the steel is higher. In addition, chromium nitrides and carbides were also observed to precipitate as a result of the heat treatments and, in the case of the chromium nitrides, they act as a favorable site for the nucleation of σ-phase and χ-phase. - Highlights: • Microscopy was used on heat treated duplex steels for microstructure identification. • FESEM–BSE observation on unetched samples provided the best contrast between phases. • Analyses of carbides, nitrides, chi and sigma phases were possible by EDS and WDS. • Chromium nitrides act as favorable site for the nucleation of chi and sigma phases. • Secondary phases nucleation kinetics are faster in superduplex than in duplex steels.

  1. Baryons as solitonic solutions of the chiral sigma model

    International Nuclear Information System (INIS)

    Bentz, W.; Hartmann, J.; Beck, F.

    1996-01-01

    Self-consistent solitonic solutions with baryon number one are obtained in the chiral quark sigma model. The translational invariant vacuum is stabilized by a Landau ghost subtraction procedure based on the requirement of the Kaellacute en-Lehmann (KL) representation for the meson propagators. The connection of this ghost free model (KL model) to the more popular Nambu-Jona-Lasinio (NJL) model is discussed in detail. copyright 1996 The American Physical Society

  2. Kinks, chains, and loop groups in the CPn sigma models

    International Nuclear Information System (INIS)

    Harland, Derek

    2009-01-01

    We consider topological solitons in the CP n sigma models in two space dimensions. In particular, we study 'kinks', which are independent of one coordinate up to a rotation of the target space, and 'chains', which are periodic in one coordinate up to a rotation of the target space. Kinks and chains both exhibit constituents, similar to monopoles and calorons in SU(n) Yang-Mills-Higgs and Yang-Mills theories. We examine the constituent structure using Lie algebras.

  3. Analysis of Lean Six Sigma in the Army Contracting Process

    Science.gov (United States)

    2011-12-01

    xii THIS PAGE INTENTIONALLY LEFT BLANK xiii LIST OF ACRONYMS AND ABBREVIATIONS AC Acquisition Center ACA Army Acquisition Agency ACAT... Utilizing the Results of Lean Six Sigma efforts (www.armyobt.army.mil) The Army mimics the DoD structure for Business Transformation to align with the DoD...understand the marketplace and work collaboratively to clearly describe the government’s requirements in a way that can generate robust competition. 15

  4. Electromagnetic axial anomaly in a generalized linear sigma model

    Science.gov (United States)

    Fariborz, Amir H.; Jora, Renata

    2017-06-01

    We construct the electromagnetic anomaly effective term for a generalized linear sigma model with two chiral nonets, one with a quark-antiquark structure, the other one with a four-quark content. We compute in the leading order of this framework the decays into two photons of six pseudoscalars: π0(137 ), π0(1300 ), η (547 ), η (958 ), η (1295 ) and η (1760 ). Our results agree well with the available experimental data.

  5. 2D Poisson sigma models with gauged vectorial supersymmetry

    Energy Technology Data Exchange (ETDEWEB)

    Bonezzi, Roberto [Dipartimento di Fisica ed Astronomia, Università di Bologna and INFN, Sezione di Bologna,via Irnerio 46, I-40126 Bologna (Italy); Departamento de Ciencias Físicas, Universidad Andres Bello,Republica 220, Santiago (Chile); Sundell, Per [Departamento de Ciencias Físicas, Universidad Andres Bello,Republica 220, Santiago (Chile); Torres-Gomez, Alexander [Departamento de Ciencias Físicas, Universidad Andres Bello,Republica 220, Santiago (Chile); Instituto de Ciencias Físicas y Matemáticas, Universidad Austral de Chile-UACh,Valdivia (Chile)

    2015-08-12

    In this note, we gauge the rigid vectorial supersymmetry of the two-dimensional Poisson sigma model presented in arXiv:1503.05625. We show that the consistency of the construction does not impose any further constraints on the differential Poisson algebra geometry than those required for the ungauged model. We conclude by proposing that the gauged model provides a first-quantized framework for higher spin gravity.

  6. Towards Resolving the Crab Sigma-Problem: A Linear Accelerator?

    Science.gov (United States)

    Contopoulos, Ioannis; Kazanas, Demosthenes; White, Nicholas E. (Technical Monitor)

    2002-01-01

    Using the exact solution of the axisymmetric pulsar magnetosphere derived in a previous publication and the conservation laws of the associated MHD flow, we show that the Lorentz factor of the outflowing plasma increases linearly with distance from the light cylinder. Therefore, the ratio of the Poynting to particle energy flux, generically referred to as sigma, decreases inversely proportional to distance, from a large value (typically approx. greater than 10(exp 4)) near the light cylinder to sigma approx. = 1 at a transition distance R(sub trans). Beyond this distance the inertial effects of the outflowing plasma become important and the magnetic field geometry must deviate from the almost monopolar form it attains between R(sub lc), and R(sub trans). We anticipate that this is achieved by collimation of the poloidal field lines toward the rotation axis, ensuring that the magnetic field pressure in the equatorial region will fall-off faster than 1/R(sup 2) (R being the cylindrical radius). This leads both to a value sigma = a(sub s) much less than 1 at the nebular reverse shock at distance R(sub s) (R(sub s) much greater than R(sub trans)) and to a component of the flow perpendicular to the equatorial component, as required by observation. The presence of the strong shock at R = R(sub s) allows for the efficient conversion of kinetic energy into radiation. We speculate that the Crab pulsar is unique in requiring sigma(sub s) approx. = 3 x 10(exp -3) because of its small translational velocity, which allowed for the shock distance R(sub s) to grow to values much greater than R(sub trans).

  7. A High Current Proton Linac with 352 MHz SC Cavities

    CERN Document Server

    Pagani, C; Pierini, P

    1996-01-01

    A proposal for a 10-120 mA proton linac employing superconducting beta-graded, CERN type, four cell cavities at 352 MHz is presented. The high energy part (100 MeV-1 GeV) of the machine is split in three beta-graded sections, and transverse focusing is provided via a periodic doublet array. All the parameters, like power in the couplers and accelerating fields in the cavities, are within the state of the art, achieved in operating machines. A first stage of operation at 30 mA beam current is proposed, while the upgrade of the machine to 120 mA operation can be obtained increasing the number of klystrons and couplers per cavity. The additional coupler ports, up to four, will be integrated in the cavity design. Preliminary calculations indicate that beam transport is feasible, given the wide aperture of the 352 MHz structures. A capital cost of less than 100 M$ at 10 mA, reaching up to 280 M$ for the 120 mA extension, has been estimated for the superconducting high energy section (100 MeV-1 GeV). The high effic...

  8. Design Considerations for the LHC 200 MHz RF System

    CERN Document Server

    Boussard, Daniel; Kindermann, H P; Linnecar, Trevor Paul R; Marque, S; Tückmantel, Joachim

    2000-01-01

    The longitudinal beam transfer from the SPS into the LHC 400 MHz buckets will not be free of losses without a lower frequency capture system and a fast longitudinal damping system in LHC. We present a complete study of a combined system using four identical copper cavities at 200 MHz delivering 3 MV total CW voltage and having still enough bandwidth to achieve fast longitudinal damping. The shape of a cavity was designed according to the accelerating mode performance, its tuning and the higher order mode spectrum with respect to the LHC beam lines and their possible attenuation. The possibility to park the cavities during coast was included. The local heat load and the corresponding cooling water distribution as well as deformations were studied and techniques to build the cavity with all ports at low cost are proposed. The parameters of the RF generators, couplers and detuning are determined. Simulations of the total LHC RF system incorporating real delays, generator bandwidth and the control loops confirm t...

  9. Mechanical design and fabrication of a 425-MHz H- buncher

    International Nuclear Information System (INIS)

    Wilson, N.G.; Precechtel, D.

    1987-01-01

    A beam buncher has been designed, fabricated, and installed on the accelerator test stand (ATS) to match the 2-MeV output beam of a 425-MHz H - radio-frequency quadrupole (RFQ) into a 425-MHz drift-tube linac (DTL). The buncher configuration provides integral-matching permanent-magnet quadrupoles (PMQ) at the exit of the RFQ and one βλ across the buncher accelerating gap; a third PMQ is the first DTL half-cell magnet. Located between the second and third PMQs is a 50-Ω, capacitively coupled, beam-sensing pickup loop. Cooling channels are provided in each of the brazed OFHC copper wall sections. Vacuum pumping of the buncher is provided by a cryogenic refrigerator vacuum pump through an array of small-diameter holes in the buncher cavity wall. Mechanical features of the buncher, the brazing and electron-beam welding of the solid-copper buncher structure, and the beam pickup loop are described in this paper. The buncher has been tuned, installed, and operated at full power on the ATS

  10. Experimental Limits on Gravitational Waves in the MHz frequency Range

    Energy Technology Data Exchange (ETDEWEB)

    Lanza, Robert Jr. [Univ. of Chicago, IL (United States)

    2015-03-01

    This thesis presents the results of a search for gravitational waves in the 1-11MHz frequency range using dual power-recycled Michelson laser interferometers at Fermi National Accelerator Laboratory. An unprecedented level of sensitivity to gravitational waves in this frequency range has been achieved by cross-correlating the output fluctuations of two identical and colocated 40m long interferometers. This technique produces sensitivities better than two orders of magnitude below the quantum shot-noise limit, within integration times of less than 1 hour. 95% confidence level upper limits are placed on the strain amplitude of MHz frequency gravitational waves at the 10-21 Hz-1/2 level, constituting the best direct limits to date at these frequencies. For gravitational wave power distributed over this frequency range, a broadband upper limit of 2.4 x 10-21Hz-1/2 at 95% confidence level is also obtained. This thesis covers the detector technology, the commissioning and calibration of the instrument, the statistical data analysis, and the gravitational wave limit results. Particular attention is paid to the end-to-end calibration of the instrument’s sensitivity to differential arm length motion, and so to gravitational wave strain. A detailed statistical analysis of the data is presented as well.

  11. VLA observations of NGC 1265 at 4886 MHz

    International Nuclear Information System (INIS)

    Owen, F.N.; Burns, J.O.; Rudnick, L.

    1978-01-01

    Observations are presented of the head-tail radio galaxy NGC 1265, made with the VLA at 4886 MHz. The total intensity brightness distribution has a resolution of 1' x 1'.5 and an rms noise of approx.150 μJy/beam area. These observations, combined with data at 2695 and 8085 MHz on a 35 km baseline in Green Bank, show that the nuclear component is less than 0'.1 and has a slightly inverted spectrum.The VLA map reveals a narrow continuous stream of emission leading away from the nucleus and out into the lower-surface brightness tail. Several small knots are superposed on the stream. This brightness distribution is compared with the independent-blob model of Jaffe and Perola. We find that the brightness distribution predicted by this model does not agree well with the observed brightness distribution. We suggest that a hot interstellar medium in the galaxy may be necessary to explain the complex structure

  12. Very high frequency (beyond 100 MHz) PZT kerfless linear arrays.

    Science.gov (United States)

    Wu, Da-Wei; Zhou, Qifa; Geng, Xuecang; Liu, Chang-Geng; Djuth, Frank; Shung, K Kirk

    2009-10-01

    This paper presents the design, fabrication, and measurements of very high frequency kerfless linear arrays prepared from PZT film and PZT bulk material. A 12-microm PZT thick film fabricated from PZT-5H powder/solution composite and a piece of 15-microm PZT-5H sheet were used to fabricate 32-element kerfless high-frequency linear arrays with photolithography. The PZT thick film was prepared by spin-coating of PZT sol-gel composite solution. The thin PZT-5H sheet sample was prepared by lapping a PZT-5H ceramic with a precision lapping machine. The measured results of the 2 arrays were compared. The PZT film array had a center frequency of 120 MHz, a bandwidth of 60% with a parylene matching layer, and an insertion loss of 41 dB. The PZT ceramic sheet array was found to have a center frequency of 128 MHz with a poorer bandwidth (40% with a parylene matching layer) but a better sensitivity (28 dB insertion loss).

  13. Resonance Frequency Readout Circuit for a 900 MHz SAW Device.

    Science.gov (United States)

    Liu, Heng; Zhang, Chun; Weng, Zhaoyang; Guo, Yanshu; Wang, Zhihua

    2017-09-15

    A monolithic resonance frequency readout circuit with high resolution and short measurement time is presented for a 900 MHz RF surface acoustic wave (SAW) sensor. The readout circuit is composed of a fractional-N phase-locked loop (PLL) as the stimulus source to the SAW device and a phase-based resonance frequency detecting circuit using successive approximation (SAR). A new resonance frequency searching strategy has been proposed based on the fact that the SAW device phase-frequency response crosses zero monotonically around the resonance frequency. A dedicated instant phase difference detecting circuit is adopted to facilitate the fast SAR operation for resonance frequency searching. The readout circuit has been implemented in 180 nm CMOS technology with a core area of 3.24 mm². In the experiment, it works with a 900 MHz SAW resonator with a quality factor of Q = 130. Experimental results show that the readout circuit consumes 7 mW power from 1.6 V supply. The frequency resolution is 733 Hz, and the relative accuracy is 0.82 ppm, and it takes 0.48 ms to complete one measurement. Compared to the previous results in the literature, this work has achieved the shortest measurement time with a trade-off between measurement accuracy and measurement time.

  14. Q0 Degradation of LANL 700-MHZ β = 0.64 Elliptical Cavities and ANL 340 MHZ Spoke Cavities

    International Nuclear Information System (INIS)

    Tajima, Tsuyoshi; Chan, Kwok-Chi D.; Edwards, Randall L.; Gentzlinger, Robert C.; Kelley, John Patrick; Krawczyk, Frank L.; Madrid, Michael A.; Montoya, Debbie I.; Schrage, Dale L.; Shapiro, Alan H.

    2002-01-01

    The quality factor (Q 0 ) of most of the six LANL β = 0.64 700-MHz 5-cell elliptical cavities starts to drop at E acc = 8-10 MV/m, which may be related to multipacting. Residual resistances of these cavities were measured to be 5.0-7.6 n(Omega). The sensitivity of surface resistance to the external magnetic field was measured to be 0.22 n(Omega)/mG. Q disease tests have shown no significant Q 0 degradation for both elliptical cavities and a spoke cavity with our 100 (micro)m BCP.

  15. Contractor Work Preparation Process Improvement Using Lean Six Sigma

    Directory of Open Access Journals (Sweden)

    Asana Kusnadi

    2016-06-01

    Full Text Available To ensure the health and safety of their workforce and protection of their assets and the environment, a global oil and gas company operating in Indonesia requires comprehensive identification and evaluation of job hazards that were included in work permitting process prior work execution in the field. Based on 20 data points obtained in August 2013, start-working time for contractors who worked for Capital Project Management (CPM Team in Facility B was in average at 09.05 a.m. The aim of this paper is to present how the firm implemented Lean Six Sigma to reduce non-added value activities while fulfilling to its safety requirements and to share lessons learned from practical and theory testing perspective. The methodology used is Lean Six Sigma’s DMAIC (Define, Measure, Analyze, Improve, Control as mandated by the corporate policy of the firm. This research adopts a mix-methods approach, by using both qualitative and quantitative data. This study was a one year longitudinal study of the Lean Six Sigma implementation to improve contractors’ work preparation process. The improvement resulted in reduction of non-value added activities and successfully increased the available working time per day by 59.3 minutes in average. The results of this case study reconfirm Lean Six Sigma as a good management theory since it shows a consistency between the theory and the real practice in a global oil and gas company in Indonesia.

  16. Application of Six Sigma Robust Optimization in Sheet Metal Forming

    International Nuclear Information System (INIS)

    Li, Y.Q.; Cui, Z.S.; Ruan, X.Y.; Zhang, D.J.

    2005-01-01

    Numerical simulation technology and optimization method have been applied in sheet metal forming process to improve design quality and shorten design cycle. While the existence of fluctuation in design variables or operation condition has great influence on the quality. In addition to that, iterative solution in numerical simulation and optimization usually take huge computational time or endure expensive experiment cost In order to eliminate effect of perturbations in design and improve design efficiency, a CAE-based six sigma robust design method is developed in this paper. In the six sigma procedure for sheet metal forming, statistical technology and dual response surface approximate model as well as algorithm of 'Design for Six Sigma (DFSS)' are integrated together to perform reliability optimization and robust improvement. A deep drawing process of a rectangular cup is taken as an example to illustrate the method. The optimization solutions show that the proposed optimization procedure not only improves significantly the reliability and robustness of the forming quality, but also increases optimization efficiency with approximate model

  17. Sigma and opioid receptors in human brain tumors

    International Nuclear Information System (INIS)

    Thomas, G.E.; Szuecs, M.; Mamone, J.Y.; Bem, W.T.; Rush, M.D.; Johnson, F.E.; Coscia, C.J.

    1990-01-01

    Human brain tumors and nude mouse-borne human neuroblastomas and gliomas were analyzed for sigma and opioid receptor content. Sigma binding was assessed using [ 3 H] 1, 3-di-o-tolylguanidine (DTG), whereas opioid receptor subtypes were measured with tritiated forms of the following: μ, [D-ala 2 , mePhe 4 , gly-ol 5 ] enkephalin (DAMGE); κ, ethylketocyclazocine (EKC) or U69,593; δ, [D-pen 2 , D-pen 5 ] enkephalin (DPDPE) or [D-ala 2 , D-leu 5 ] enkephalin (DADLE) with μ suppressor present. Binding parameters were estimated by homologous displacement assays followed by analysis using the LIGAND program. Sigma binding was detected in 15 of 16 tumors examined with very high levels found in a brain metastasis from an adenocarcinoma of lung and a human neuroblastoma (SK-N-MC) passaged in nude mice. κ opioid receptor binding was detected in 4 of 4 glioblastoma multiforme specimens and 2 of 2 human astrocytoma cell lines tested but not in the other brain tumors analyzed

  18. Sigma and opioid receptors in human brain tumors

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, G.E.; Szuecs, M.; Mamone, J.Y.; Bem, W.T.; Rush, M.D.; Johnson, F.E.; Coscia, C.J. (St. Louis Univ. School of Medicine, MO (USA))

    1990-01-01

    Human brain tumors and nude mouse-borne human neuroblastomas and gliomas were analyzed for sigma and opioid receptor content. Sigma binding was assessed using ({sup 3}H) 1, 3-di-o-tolylguanidine (DTG), whereas opioid receptor subtypes were measured with tritiated forms of the following: {mu}, (D-ala{sup 2}, mePhe{sup 4}, gly-ol{sup 5}) enkephalin (DAMGE); {kappa}, ethylketocyclazocine (EKC) or U69,593; {delta}, (D-pen{sup 2}, D-pen{sup 5}) enkephalin (DPDPE) or (D-ala{sup 2}, D-leu{sup 5}) enkephalin (DADLE) with {mu} suppressor present. Binding parameters were estimated by homologous displacement assays followed by analysis using the LIGAND program. Sigma binding was detected in 15 of 16 tumors examined with very high levels found in a brain metastasis from an adenocarcinoma of lung and a human neuroblastoma (SK-N-MC) passaged in nude mice. {kappa} opioid receptor binding was detected in 4 of 4 glioblastoma multiforme specimens and 2 of 2 human astrocytoma cell lines tested but not in the other brain tumors analyzed.

  19. Study of Sigma Phase in Duplex SAF 2507

    Science.gov (United States)

    Fellicia, D. M.; Sutarsis; Kurniawan, B. A.; Wulanari, D.; Purniawan, A.; Wibisono, A. T.

    2017-05-01

    Super duplex stainless steel is one of the stainless steel which has a combination between high strength properties and excellent corrosion resistance. However, the resistance can decrease by precipitation of sigma phase which is formed at high temperature, for example after welding processes. A series of experiments has been performed to study the effect of solution annealing to existence of sigma phase on super duplex SAF 2507. Variations of solution-annealing temperatures were 1000 °C, 1065 °C and 1125 °C with holding time of 15 and 30 minutes for each temperature. Effect of solution annealing process was characterized by using XRD, SEM, and Optical Microscopy. The result showed precipitation of sigma phase completely dissolved at 1065 °C and 1125 °C because it reformed to austenite. After it was heated at 1065 °C, chromium carbide appeared in ferrite site and grain boundary. The amount of chromium carbide increased with the increasing of solution annealing temperature.

  20. Squashed Toric Sigma Models and Mock Modular Forms

    Science.gov (United States)

    Gupta, Rajesh Kumar; Murthy, Sameer

    2018-05-01

    We study a class of two-dimensional N}=(2,2)} sigma models called squashed toric sigma models, using their Gauged Linear Sigma Models (GLSM) description. These models are obtained by gauging the global {U(1)} symmetries of toric GLSMs and introducing a set of corresponding compensator superfields. The geometry of the resulting vacuum manifold is a deformation of the corresponding toric manifold in which the torus fibration maintains a constant size in the interior of the manifold, thus producing a neck-like region. We compute the elliptic genus of these models, using localization, in the case when the unsquashed vacuum manifolds obey the Calabi-Yau condition. The elliptic genera have a non-holomorphic dependence on the modular parameter {τ} coming from the continuum produced by the neck. In the simplest case corresponding to squashed {C / Z_{2 the elliptic genus is a mixed mock Jacobi form which coincides with the elliptic genus of the {N=(2,2)} {SL(2,R) / U(1)} cigar coset.

  1. The GMRT 150 MHz all-sky radio survey. First alternative data release TGSS ADR1

    Science.gov (United States)

    Intema, H. T.; Jagannathan, P.; Mooley, K. P.; Frail, D. A.

    2017-02-01

    We present the first full release of a survey of the 150 MHz radio sky, observed with the Giant Metrewave Radio Telescope (GMRT) between April 2010 and March 2012 as part of the TIFR GMRT Sky Survey (TGSS) project. Aimed at producing a reliable compact source survey, our automated data reduction pipeline efficiently processed more than 2000 h of observations with minimal human interaction. Through application of innovative techniques such as image-based flagging, direction-dependent calibration of ionospheric phase errors, correcting for systematic offsets in antenna pointing, and improving the primary beam model, we created good quality images for over 95 percent of the 5336 pointings. Our data release covers 36 900 deg2 (or 3.6 π steradians) of the sky between -53° and +90° declination (Dec), which is 90 percent of the total sky. The majority of pointing images have a noise level below 5 mJy beam-1 with an approximate resolution of 25''×25'' (or 25''×25''/ cos(Dec-19°) for pointings south of 19° declination). We have produced a catalog of 0.62 Million radio sources derived from an initial, high reliability source extraction at the seven sigma level. For the bulk of the survey, the measured overall astrometric accuracy is better than two arcseconds in right ascension and declination, while the flux density accuracy is estimated at approximately ten percent. Within the scope of the TGSS alternative data release (TGSS ADR) project, the source catalog, as well as 5336 mosaic images (5°×5°) and an image cutout service, are made publicly available at the CDS as a service to the astronomical community. Next to enabling a wide range of different scientific investigations, we anticipate that these survey products will provide a solid reference for various new low-frequency radio aperture array telescopes (LOFAR, LWA, MWA, SKA-low), and can play an important role in characterizing the epoch-of-reionisation (EoR) foreground. The TGSS ADR project aims at

  2. Thermal isomerizations of ketenimines to nitriles: evaluations of sigma-Dot (sigma(*)) constants for spin-delocalizations

    Science.gov (United States)

    Kim; Zhu; Lee

    2000-05-19

    Rate constants (k(Y)) of the isomerizations of 11 diphenyl N-(substituted benzyl) ketenimines were measured at 40, 50, 60, and 70 degrees C. Activation parameters DeltaH()(Y) and DeltaS()(Y) were obtained using the Eyring equation. The relative rates (k(Y)/k(H)) were fitted into Hammett single correlations (log k(Y)/k(H) = rhosigma and log k(Y)/k(H) = rho(*)sigma(*)). The single correlations have been compared with Hammett dual correlations (log k(Y)/k(H) = rhosigma + rho(*)sigma(*) ). Separate treatments of para and meta substituents yielded even better correlations. Para substituents control the rates through spin-delocalizations and inductive effects. The former outweighs the latter when the latter exerts a modest but distinct influence on the rates. On the other hand, inductive effects are the "major" or the sole interactions triggered by meta substituents.

  3. The C-Terminal RpoN Domain of sigma54 Forms an unpredictedHelix-Turn-Helix Motif Similar to domains of sigma70

    Energy Technology Data Exchange (ETDEWEB)

    Doucleff, Michaeleen; Malak, Lawrence T.; Pelton, Jeffrey G.; Wemmer, David E.

    2005-11-01

    The ''{delta}'' subunit of prokaryotic RNA-polymerase allows gene-specific transcription initiation. Two {sigma} families have been identified, {sigma}{sup 70} and {sigma}{sup 54}, which use distinct mechanisms to initiate transcription and share no detectable sequence homology. Although the {sigma}{sup 70}-type factors have been well characterized structurally by x-ray crystallography, no high-resolution structural information is available for the {sigma}{sup 54}-type factors. Here we present the NMR derived structure of the C-terminal domain of {sigma}{sup 54} from Aquifex aeolicus. This domain (Thr323 to Gly389), which contains the highly conserved RpoN box sequence, consists of a poorly structured N-terminal tail followed by a three-helix bundle, which is surprisingly similar to domains of the {sigma}{sup 70}-type proteins. Residues of the RpoN box, which have previously been shown to be critical for DNA binding, form the second helix of an unpredicted helix-turn-helix motif. This structure's homology with other DNA binding proteins, combined with previous biochemical data, suggest how the C-terminal domain of {sigma}{sup 54} binds to DNA.

  4. Comparison of 250 MHz R10K Origin 2000 and 400 MHz Origin 2000 Using NAS Parallel Benchmarks

    Science.gov (United States)

    Turney, Raymond D.; Thigpen, William W. (Technical Monitor)

    2001-01-01

    This report describes results of benchmark tests on Steger, a 250 MHz Origin 2000 system with R10K processors, currently installed at the NASA Ames National Advanced Supercomputing (NAS) facility. For comparison purposes, the tests were also run on Lomax, a 400 MHz Origin 2000 with R12K processors. The BT, LU, and SP application benchmarks in the NAS Parallel Benchmark Suite and the kernel benchmark FT were chosen to measure system performance. Having been written to measure performance on Computational Fluid Dynamics applications, these benchmarks are assumed appropriate to represent the NAS workload. Since the NAS runs both message passing (MPI) and shared-memory, compiler directive type codes, both MPI and OpenMP versions of the benchmarks were used. The MPI versions used were the latest official release of the NAS Parallel Benchmarks, version 2.3. The OpenMP versions used were PBN3b2, a beta version that is in the process of being released. NPB 2.3 and PBN3b2 are technically different benchmarks, and NPB results are not directly comparable to PBN results.

  5. The Zeeman effect in the (0,0) band of the A 7Pi-X 7Sigma(+) transition of manganese monohydride, MnH.

    Science.gov (United States)

    Steimle, Timothy C; Wang, Hailing; Gengler, Jamie J; Stoll, Michael; Meijer, Gerard

    2008-10-28

    The Zeeman tuning of the P(1)(0) line (nu=17 568.35 cm(-1)) of the A (7)Pi-X (7)Sigma(+) (0,0) band of manganese monohydride, MnH, has been investigated. The laser induced fluorescence spectrum of a supersonic molecular beam sample was recorded at a resolution of approximately 40 MHz and with field strengths of up to 362.0 mT. The observed spectrum was successfully fitted using a traditional effective Zeeman Hamiltonian to determine an effective magnetic g-factor for the J=2 level of the F(1)-spin component of the A (7)Pi(v=0) state. Spectral predictions of the P(1)(0) line at field strengths used in magnetic trapping experiments are presented.

  6. Naval Surface Warfare Center Dahlgren Division: application of Lean Six Sigma in the pre-award procurement process

    OpenAIRE

    Himes, Kristy M.; Salisbury, Constance M.

    2008-01-01

    Joint Applied Project This Project outlines Lean Six Sigma principles, provides examples of Lean Six Sigma events, and analyzes principles that can be applied to Navy acquisition and contracting. The objective of this project is to: (1) provide an overview of Lean Six Sigma principles in contracting and acquisition; (2) identify Navy contracting processes that have and can be analyzed using Lean Six Sigma principles; (3) explore how Lean Six Sigma can be applied to interpret and implem...

  7. 915-MHz Radar Wind Profiler (915RWP) Handbook

    Energy Technology Data Exchange (ETDEWEB)

    Coulter, R

    2005-01-01

    The 915 MHz radar wind profiler/radio acoustic sounding system (RWP/RASS) measures wind profiles and backscattered signal strength between (nominally) 0.1 km and 5 km and virtual temperature profiles between 0.1 km and 2.5 km. It operates by transmitting electromagnetic energy into the atmosphere and measuring the strength and frequency of backscattered energy. Virtual temperatures are recovered by transmitting an acoustic signal vertically and measuring the electromagnetic energy scattered from the acoustic wavefront. Because the propagation speed of the acoustic wave is proportional to the square root of the virtual temperature of the air, the virtual temperature can be recovered by measuring the Doppler shift of the scattered electromagnetic wave.

  8. The seven components of Hα and the 9873 MHz line

    International Nuclear Information System (INIS)

    Zelenka, A.

    1978-01-01

    Under conditions pertaining to the middle chromosphere, the nlj-substates of the n = 2 and n = 3 states of hydrogen are found to be populated proportionally to their degree of degeneracy. Thus, the non-LTE formation of the Hα line is not expected to be influenced by some exotic excitation conditions in one of its seven components. The overpopulation of the 2Ssub(1/2) substate relative to the 2Psub(3/2) substate does not depend upon details of the radiative transfer in Hα, so that it rests wholly on the transfer in Lα (Milkey and Mihalas, 1973). One-component plane parallel models of the chromosphere thus further predict that the 2Ssub(1/2)-2Psub(3/2), 9873 MHz (3.04 cm) line will not be observeable in the radio-spectrum of the quiet Sun. (Auth.)

  9. Parametric thermal analysis of 75 MHz heavy ion RFQ

    International Nuclear Information System (INIS)

    Mishra, N.K.; Mehrotra, N.; Verma, V.; Gupta, A.K.; Bhagwat, P.V.

    2015-01-01

    An ECR based Heavy Ion Accelerator comprising of a superconducting Electron Cyclotron Resonance (ECR) Ion Source, normal conducting RFQ (Radio Frequency Quadrupole) and superconducting Niobium resonators is being developed at BARC under XII plan. A state-of-the-art 18 GHz superconducting ECR ion source (PK-ISIS) jointly configured with Pantechnik, France is operational at Van-de-Graaff, BARC. The electromagnetic design of the improved version of 75 MHz heavy ion RFQ has been reported earlier. The previous thermal study of 51 cm RFQ model showed large temperature variation axially along the vane tip. A new coolant flow scheme has been worked out to optimize the axial temperature gradient. In this paper the thermal analysis including parametric study of coolant flow rates and inlet temperature variation will be presented. (author)

  10. Optimized 425MHz passive wireless magnetic field sensor

    KAUST Repository

    Li, Bodong

    2014-06-01

    A passive, magnetic field sensor consisting of a 425 MHz surface acoustic wave device loaded with a giant magnetoimpedance element is developed. The GMI element with a multilayer structure composed of Ni80Fe 20/Cu/Ni80Fe20, is fabricated on a 128° Y-X cut LiNbO3 LiNbO3 substrate. The integrated sensor is characterized with a network analyzer through an S-parameter measurement. Upon the application of a magnetic field, a maximum magnitude change and phase shift of 7.8 dB and 27 degree, respectively, are observed. Within the linear region, the magnetic sensitivity is 1.6 dB/Oe and 5 deg/Oe. © 2014 IEEE.

  11. 352.2 MHz rf system for the ESRF

    International Nuclear Information System (INIS)

    Jacob, J.; David, C.

    1988-01-01

    This paper reports that ESRF's 352.2 MHz RF system that uses 1 MW-CW klystrons and five-cell LEP type cavities has been adopted. In the storage ring (SR), two klystrons will feed a total of four cavities in order to provide the maximum required accelerating voltage of 8.9 MV. In the injector synchrotron (SY), two cavities fed by one klystron in a cycling mode at 10 Hz will give the maximum needed accelerating voltage of 7.3 MV. In multibunch operation of the SR, coupled bunch oscillations will be driven by the higher order modes (HOMs) of the cavities, and may limit the maximum beam current to about 60 mA. Spare ports will allow to install HOM dampers on the cavities in order to raise the instability thresholds above the design current of 100 mA. In addition, active feed back systems may be implemented

  12. 201 MHz Cavity R and D for MUCOOL and MICE

    International Nuclear Information System (INIS)

    Li, Derun; Virostek, Steve; Zisman, Michael; Norem, Jim; Bross, Alan; Moretti, Alfred; Norris, Barry; Torun, Yagmur; Phillips, Larry; Rimmer, Robert; Stirbet, Mircea; Reep, Michael; Summers, Don

    2006-01-01

    We describe the design, fabrication, analysis and preliminary testing of the prototype 201 MHz copper cavity for a muon ionization cooling channel. Cavity applications include the Muon Ionization Cooling Experiment (MICE) as well as cooling channels for a neutrino factory or a muon collider. This cavity was developed by the US muon cooling (MUCOOL) collaboration and is being tested in the MUCOOL Test Area (MTA) at Fermilab. To achieve a high accelerating gradient, the cavity beam irises are terminated by a pair of curved, thin beryllium windows. Several fabrication methods developed for the cavity and windows are novel and offer significant cost savings as compared to conventional construction methods. The cavity's thermal and structural performances are simulated with an FEA model. Preliminary high power RF commissioning results will be presented

  13. Commissioning of the 400 MHz LHC RF System

    CERN Document Server

    Ciapala, Edmond; Baudrenghien, P; Brunner, O; Butterworth, A; Linnecar, T; Maesen, P; Molendijk, J; Montesinos, E; Valuch, D; Weierud, F

    2008-01-01

    The installation of the 400 MHz superconducting RF system in LHC is finished and commissioning is under way. The final RF system comprises four cryo-modules each with four cavities in the LHC tunnel straight section round IP4. Also underground in an adjacent cavern shielded from the main tunnel are the sixteen 300 kW klystron RF power sources with their high voltage bunkers, two Faraday cages containing RF feedback and beam control electronics, and racks containing all the slow controls. The system and the experience gained during commissioning will be described. In particular, results from conditioning the cavities and their movable main power couplers and the setting up of the low level RF feedbacks will be presented.

  14. 47 CFR 22.970 - Unacceptable interference to part 90 non-cellular 800 MHz licensees from cellular radiotelephone...

    Science.gov (United States)

    2010-10-01

    ...-cellular 800 MHz licensees from cellular radiotelephone or part 90-800 MHz cellular systems. 22.970 Section... MOBILE SERVICES Cellular Radiotelephone Service § 22.970 Unacceptable interference to part 90 non-cellular 800 MHz licensees from cellular radiotelephone or part 90-800 MHz cellular systems. (a) Definition...

  15. Study of the critical behavior of the O(N) linear and nonlinear sigma models

    International Nuclear Information System (INIS)

    Graziani, F.R.

    1983-01-01

    A study of the large N behavior of both the O(N) linear and nonlinear sigma models is presented. The purpose is to investigate the relationship between the disordered (ordered) phase of the linear and nonlinear sigma models. Utilizing operator product expansions and stability analyses, it is shown that for 2 - (lambda/sub R/(M) is the dimensionless renormalized quartic coupling and lambda* is the IR fixed point) limit of the linear sigma model which yields the nonlinear sigma model. It is also shown that stable large N linear sigma models with lambda 0) and nonlinear models are trivial. This result (i.e., triviality) is well known but only for one and two component models. Interestingly enough, the lambda< d = 4 linear sigma model remains nontrivial and tachyonic free

  16. Some Practical Issues in the Application of Lean Six Sigma to Service Systems

    Directory of Open Access Journals (Sweden)

    Goh Thong-Ngee

    2014-11-01

    Full Text Available Six Sigma as a quality improvement framework has gained considerable popularity in the past two decades. Its extension Lean Six Sigma has also been embraced by many organizations for improvement of quality and business competitiveness. One important factor for the popularity of Six Sigma and Lean Six Sigma is their potential for improving service systems, in contrast to the conventional perceptions that only manufacturing systems can benefit from statistics-based methodologies. There are however a number of issues related to the nature of service systems that must be resolved before the full benefits of Lean Six Sigma can be realized. In this paper, these issues are discussed from a practical point of view from three angles: analytical, organizational, and personal. Awareness of the existence of such issues, if not the answers to all of them, is a pre-requisite to effective adoption of Lean Six Sigma tools.

  17. Seis Sigma: Fatores Críticos de Sucesso para sua Implantação

    Directory of Open Access Journals (Sweden)

    Antonio Cesar Amaru Maximiano

    2009-10-01

    Full Text Available This article describes an investigation of critical success factors to implement Six Sigma in organizations operating in the Brazilian market place. Besides that, a secondary objective was to investigate the relationship between aspects like success perception among those companies which implemented Six Sigma, company size, company nationality, time of Six Sigma of implementation, continuous training, communication level between professionals, full-time and part-time Black Belts, project completion, project duration and project savings. Data were collected through an Internet questionnaire, distributed by email and sent to discussion groups involving Six Sigma professionals. Questionnaire development included a literature review and interviews with experienced Six Sigma professionals. The results indicated eight critical success factors for Six Sigma implementation: (a Leadership, (b Projects, (c Training, (d Communication and Review, (e Managerial Process, (f Black Belts Profile, (g Project Teams and (h Previous Quality Initiatives.

  18. Improving ED specimen TAT using Lean Six Sigma.

    Science.gov (United States)

    Sanders, Janet H; Karr, Tedd

    2015-01-01

    Lean and Six Sigma are continuous improvement methodologies that have garnered international fame for improving manufacturing and service processes. Increasingly these methodologies are demonstrating their power to also improve healthcare processes. The purpose of this paper is to discuss a case study for the application of Lean and Six Sigma tools in the reduction of turnaround time (TAT) for Emergency Department (ED) specimens. This application of the scientific methodologies uncovered opportunities to improve the entire ED to lab system for the specimens. This case study provides details on the completion of a Lean Six Sigma project in a 1,000 bed tertiary care teaching hospital. Six Sigma's Define, Measure, Analyze, Improve, and Control methodology is very similar to good medical practice: first, relevant information is obtained and assembled; second, a careful and thorough diagnosis is completed; third, a treatment is proposed and implemented; and fourth, checks are made to determine if the treatment was effective. Lean's primary goal is to do more with less work and waste. The Lean methodology was used to identify and eliminate waste through rapid implementation of change. The initial focus of this project was the reduction of turn-around-times for ED specimens. However, the results led to better processes for both the internal and external customers of this and other processes. The project results included: a 50 percent decrease in vials used for testing, a 50 percent decrease in unused or extra specimens, a 90 percent decrease in ED specimens without orders, a 30 percent decrease in complete blood count analysis (CBCA) Median TAT, a 50 percent decrease in CBCA TAT Variation, a 10 percent decrease in Troponin TAT Variation, a 18.2 percent decrease in URPN TAT Variation, and a 2-5 minute decrease in ED registered nurses rainbow draw time. This case study demonstrated how the quantitative power of Six Sigma and the speed of Lean worked in harmony to improve

  19. Signal-to-noise ratio estimation in digital computer simulation of lowpass and bandpass systems with applications to analog and digital communications, volume 3

    Science.gov (United States)

    Tranter, W. H.; Turner, M. D.

    1977-01-01

    Techniques are developed to estimate power gain, delay, signal-to-noise ratio, and mean square error in digital computer simulations of lowpass and bandpass systems. The techniques are applied to analog and digital communications. The signal-to-noise ratio estimates are shown to be maximum likelihood estimates in additive white Gaussian noise. The methods are seen to be especially useful for digital communication systems where the mapping from the signal-to-noise ratio to the error probability can be obtained. Simulation results show the techniques developed to be accurate and quite versatile in evaluating the performance of many systems through digital computer simulation.

  20. Improvement of Production Quality by using Six Sigma Technique:

    Directory of Open Access Journals (Sweden)

    Sawsan Ali

    2013-04-01

    Full Text Available As a result of lack of conformity of the outer diameter of the filling piston of plastic syringe to the specifications set out in the design map and the increased demand for its  products from the Medical syringes factory – Babylon. The research conducts the necessary investigations and  analysis of the production process as most of the units rejected by fact that the outer diameter of the filling piston is smaller than the minimum specification and units returned to work  due to the fact that  the outer diameter larger than the upper limit of the specification.13The research aims firstly to examine the outer diameter of the filling piston through the use of the control chart of the variables represented by the average , and its impact on the production process capability because the increase in diameter specification leads to an increase in the pressure imposed on the lining of the cylinder, causing difficulty in piston movement and a decrease in diameter specification which leads to loose the process capability to prevent leakage of fluid, causing air to enter as well as to speed the movement of the piston, which negatively affects human life in both cases. Secondly, study the possibility of improving the production process capability by using advanced levels of the sigma.The results showed that the production process in the case of a disciplined and follows a normal distribution, the pointer of  the production process capability is equal to (0.55 and the factory works within the level of Sigma equal to (1.65. The proportion of a damaged product is (15.8 % and rework (0.99 %.In order to  reduce the proportion of damaged product, this paper introduces a quality plan depending on ( ±0.025 as tolerance limits instead of ( ±0.05 to increase sigma level by 202%.