Corrosion analysis of AlMg2 and AlMgSi using electrochemical method

International Nuclear Information System (INIS)

Dian A; Maman Kartaman; Rosika K; Yanlinastuti

2014-01-01

Corrosion test of cladding materials and structures of research reactor fuel, AlMgSi and AlMg2 have been performed in demineralized water of pH 2 and 6.7 using an electrochemical method. Corrosion phenomenon is affected by several factor such as composition and condition of solution. The purpose of this activity is to investigate the corrosion phenomena through the determination of the parameters of corrosion and polarization curve. The materials used are AlMg2 and AlMgSi alloy in circular dish shape with an area of 1 Cm"2. Preparation of the test sample is performed through several stages polishing, cleaning and drying procedures followed ASTM G3. The electrochemical method is done by measuring the open circuit potential (OCP), polarization resistance and potentiodynamic in demineralized water of pH 2 and pH 6.7 at temperature of 25°C. The results of the OCP is the corrosion potential (Ecorr) of AlMg2 and AlMgSi each of -906.1 mV and -619.8 mV at pH 2 and -868.6 and -756.7 mV at pH 6.7 mV. The results of measurements by polarization resistance technique showed that the corrosion rate of AlMg2 and AlMgSi in safe category (<2 mpy) at pH 6.7 and at pH 2 corrosion rate increased significantly, but still in the lightweight category (<20 mpy). Potentiodynamic curves showed that the passivation at pH 6.7 is very low while the passivation at pH 2 occurs within a relatively short range potential and followed events corroded. (author)

Mg2BIV: Narrow Bandgap Thermoelectric Semiconductors

Science.gov (United States)

Kim, Il-Ho

2018-05-01

Thermoelectric materials can convert thermal energy directly into electric energy and vice versa. The electricity generation from waste heat via thermoelectric devices can be considered as a new energy source. For instance, automotive exhaust gas and all industrial processes generate an enormous amount of waste heat that can be converted to electricity by using thermoelectric devices. Magnesium compound Mg2BIV (BIV = Si, Ge or Sn) has a favorable combination of physical and chemical properties and can be a good base for the development of new efficient thermoelectrics. Because they possess similar properties to those of group BIV elemental semiconductors, they have been recognized as good candidates for thermoelectric applications. Mg2Si, Mg2Ge and Mg2Sn with an antifluorite structure are narrow bandgap semiconductors with indirect band gaps of 0.77 eV, 0.74 eV, and 0.35 eV, respectively. Mg2BIV has been recognized as a promising material for thermoelectric energy conversion at temperatures ranging from 500 K to 800 K. Compared to other thermoelectric materials operating in the similar temperature range, such as PbTe and filled skutterudites, the important aspects of Mg2BIV are non-toxic and earth-abundant elements. Based on classical thermoelectric theory, the material factor β ( m* / m e)3/2μκ L -1 can be utilized as the criterion for thermoelectric material selection, where m* is the density-of-states effective mass, me is the mass of an electron, μ is the carrier mobility, and κL is the lattice thermal conductivity. The β for magnesium silicides is 14, which is very high compared to 0.8 for iron silicides, 1.4 for manganese silicides, and 2.6 for silicon-germanium alloys. In this paper, basic phenomena of thermoelectricity and transport parameters for thermoelectric materials were briefly introduced, and thermoelectric properties of Mg2BIV synthesized by using a solid-state reaction were reviewed. In addition, various Mg2BIV compounds were discussed

Anions Analysis in Ground and Tap Waters by Sequential Chemical and CO2-Suppressed Ion Chromatography

Directory of Open Access Journals (Sweden)

Glen Andrew D. De Vera

2011-06-01

Full Text Available An ion chromatographic method using conductivity detection with sequential chemical and CO2 suppression was optimized for the simultaneous determination of fluoride, chloride, bromide, nitrate,phosphate and sulfate in ground and tap water. The separation was done using an anion exchange column with an eluent of 3.2 mM Na2CO3 and 3.2 mM NaHCO3 mixture. The method was linear in the concentration range of 5 to 300 μg/L with correlation coefficients greater than 0.99 for the six inorganic anions. The method was also shown to be applicable in trace anions analysis as given by the low method detection limits (MDL. The MDL was 1μg/L for both fluoride and chloride. Bromide, nitrate, phosphate and sulfate had MDLs of 7 μg/L, 10 μg/L, 9 μg/L and 2 μg/L, respectively. Good precision was obtained as shown in the relative standard deviation of 0.1 to 12% for peak area and 0.1 to 0.3% for retention time. The sensitivity of the method improved with the addition of CO2 suppressor to chemical suppression as shown in the lower background conductivity and detection limits. The recoveries of the anions spiked in water at 300 μg/L level ranged from 100 to 104%. The method was demonstrated to be sensitive, accurate and precise for trace analysis of the six anions and was applied in the anions analysis in ground and tap waters in Malolos, Bulacan. The water samples were found to contain high concentrations of chloride of up to 476 mg/L followed by sulfate (38 mg/L, bromide (1 mg/L, phosphate (0.4 mg/L, fluoride (0.2 mg/L and nitrate (0.1 mg/L.

Comparison of effects of ATP-MgCl2 and adenosine-MgCl2 on renal function following ischemia

International Nuclear Information System (INIS)

Sumpio, B.E.; Hull, M.J.; Baue, A.E.; Chaudry, I.H.

1987-01-01

ATO-MgCl 2 administration had been shown to accelerate the recovery of renal function following warm ischemia. However, since the major breakdown product of ATP is adenosine, the relative contribution of ATP vs. adenosine in improving renal function following ischemia remains to be determined. To study this, kidneys were subjected to 45 min of normothermic ischemia and then perfused at 100 mmHg with oxygenated Krebs-HCO 3 buffer containing albumin, [ 3 H]inulin, substrates, and either 0.3 mM ATP-MgCl 2 or adenosine-MgCl 2 for 110 min. Perfusate and timed urine samples were collected and analyzed for radioactivity and [Na + ]. The functional parameters indicated that although adenosine-MgCl 2 treatment provided a transient improvement, it failed to provided a sustained improvement in renal function or attain control valued compared with ATP-MgCl 2 treatment. Thus, the salutary effects of ATP-MgCl 2 following warm ischemia in the kidney are not mediated by adenosine

Structural determination of new solid solutions [Y2-x Mx ][Sn2-x Mx ]O7-3x/2 (M = Mg or Zn by Rietveld method

Directory of Open Access Journals (Sweden)

Mohamed Douma

2010-12-01

Full Text Available New [Y2-x Mx][Sn2-x Mx]O7-3x/2 (0 ≤x≤ 0.30 for M = Mg and 0 ≤x≤ 0.36 for M = Zn solid solutions with the pyrochlore structure were synthesized via high-temperature solid-state reaction method. Powder X-ray diffraction (PXRD patterns and Fourier transform infrared (FT-IR spectra showed that these materials are new non-stoichiometric solid solutions with the pyrochlore type structure. The structural parameters for the solids obtained were successfully determined by Rietveld refinement based on the analysis of the PXRD diagrams. Lattice parameter (a of these solid solutions decreases when x increases in both series. All samples obtained have the pyrochlore structure Fd-3m, no. 227 (origin at center -3m with M2+ (M = Mg2+ or Zn2+ cations in Y3+ and Sn4+ sites, thus creating vacancies in the anionic sublattice.

Fabrication and spectroscopic properties of Co:MgAl2O4 transparent ceramics by the HIP post-treatment

Science.gov (United States)

Luo, Wei; Ma, Peng; Xie, Tengfei; Dai, Jiawei; Pan, Yubai; Kou, Huamin; Li, Jiang

2017-07-01

Cobalt-doped magnesium aluminate spinel (Co:MgAl2O4) is one of the most important saturable absorbers for the passive Q-switching of solid-state lasers operating at eye-safe wavelength of 1.5 μm. In this work, highly transparent Co:MgAl2O4 ceramics were fabricated by vacuum sintering combined with hot isostatic pressing (HIP) post-treatment, using the mixture of the commercial spinel and the lab-made Co:MgAl2O4 powder as the raw materials. The densification mechanism of Co:MgAl2O4 transparent ceramics was discussed. The microstructure and optical properties of the samples were investigated. The ground state absorption cross section (σGSA) was calculated from the fitted curve of the absorption coefficient spectrum. The results show that Co:MgAl2O4 ceramics fabricated by vacuum sintering at 1500 °C for 5 h and then HIP post-treatment at 1650 °C for 3 h perform good transparency, whose in-line transmittance exceeds 80% at 2500 nm. Moreover, the ground state absorption cross section of 0.02 at.% Co:MgAl2O4 ceramics is calculated to be 3.35 × 10-19 cm2 at the wavelength of 1540 nm, which is promising for the application to the passive Q-switching of solid-state laser operating in the near infrared region (NIR).

Magnetic characteristics of M2FeV3O11 (M = Mg, Zn, Pb, Co, Ni) compounds

Science.gov (United States)

Groń, T.; Blonska-Tabero, A.; Filipek, E.; Stokłosa, Z.; Duda, H.; Sawicki, B.

2018-02-01

The unusual physical characteristics of the multicomponent oxide systems renewed the interest as the potential cathode materials in high-energy cells. Since the earlier magnetic characteristics were not entirely conclusive, we report the results of dc magnetic measurements including higher harmonics of ac magnetic susceptibility of the M2FeV3O11 (M = Mg, Zn, Pb, Co, Ni) compounds. Ferrimagnetic long-range and antiferromagnetic short-range interactions for all compounds under study at low temperatures as well as superparamagnetic-like behavior with the blocking temperature of 29 K and the freezing parameter of 0.013 were observed. These effects are discussed within the framework of superexchange and double exchange magnetic interactions as well as the mixed valence band of iron ions.

Comparison of weekly administration of cisplatin versus three courses of cisplatin 100 mg/m2 for definitive radiochemotherapy of locally advanced head-and-neck cancers

International Nuclear Information System (INIS)

Rades, Dirk; Seidl, Daniel; Janssen, Stefan; Bajrovic, Amira; Karner, Katarina; Strojan, Primoz; Schild, Steven E

2016-01-01

To compare definitive radiochemotherapy with weekly administration of 30–40 mg/m 2 of cisplatin to 100 mg/m 2 of cisplatin on days 1, 22 and 43 for outcomes and toxicity in patients with squamous cell carcinoma of the head-and-neck. Seventy-five patients receiving radiochemotherapy with weekly cisplatin (30–40 mg/m 2 ) were compared to 58 patients receiving radiochemotherapy with 100 mg/m 2 cisplatin on days 1, 22 and 43. Radiochemotherapy regimen plus seven characteristics (age, gender, performance score, tumor site, T-/N-category, histologic grading) were evaluated for locoregional control (LRC), metastases-free survival (MFS) and overall survival (OS). Radiochemotherapy groups were compared for toxicity. On multivariate analysis, improved LRC was associated with cisplatin 100 mg/m 2 (hazard ratio [HR] 1.57; p = 0.008) and female gender (HR 4.37; p = 0.003). Radiochemotherapy regimen was not significantly associated with MFS on univariate analysis (p = 0.66). On multivariate analysis, better MFS was associated with ECOG performance score 0–1 (HR 5.63; p < 0.001) and histological grade 1–2 (HR 1.81; p = 0.002). On multivariate analysis, improved OS was associated with cisplatin 100 mg/m 2 (HR 1.33; p = 0.023), ECOG performance score 0–1 (HR 2.15; p = 0.029) and female gender (HR 1.98; p = 0.026). Cisplatin 100 mg/m 2 was associated with higher rates of grade ≥3 hematotoxicity (p = 0.004), grade ≥2 renal failure (p = 0.004) and pneumonia/sepsis (p = 0.033). Radiochemotherapy with 100 mg/m 2 of cisplatin every 3 weeks resulted in better LRC and OS than weekly doses of 30–40 mg/m 2 . Given the limitations of a retrospective study, 100 mg/m 2 of cisplatin appears preferable. Since this regimen was associated with considerable acute toxicity, patients require close monitoring

Search for 12 C+ 12 C clustering in 24 Mg ground state

Indian Academy of Sciences (India)

In the backdrop of many models, the heavy cluster structure of the ground state of 24 Mg has been probed experimentally for the first time using the heavy cluster knockout reaction 24 Mg( 12 C, 212 C) 12 C in thequasifree scattering kinematic domain. In the ( 12 C, 212 C) reaction, the direct 12 C-knockout cross-section was ...

Industrial production of MgH2 and its application

International Nuclear Information System (INIS)

Uesugi, H.; Sugiyama, T.; Nii, H.; Ito, T.; Nakatsugawa, I.

2011-01-01

Research highlights: → Tablet and powder Mg were hydrogenated in a 50 kg batch furnace based on thermal equilibrium method. → Compression of Mg tablet improved the hydrogenation yield. → Hydrolysis of MgH 2 using citric acid generated hydrogen under 373 K. → A MgH 2 -hydrogen reactor utilizing hydraulic head pressure was developed. → - Abstract: A process for the industrial production of magnesium hydride (MgH 2 ) based on a thermal equilibrium method and its application to portable hydrogen sources is proposed. Mg powders and tablets compressed with mechanically ground Mg ribbons were successfully hydrogenated in a 50-kg-batch furnace. The resultant MgH 2 showed a hydrogen yield of around 96% with good reproducibility. The compression ratio of Mg tablets was found to be an important factor in the hydrogenation yield. A hydrolysis technique using citric acid as an additive was employed to generate hydrogen under 373 K. Increasing the concentration of citric acid and the temperature accelerated the hydrolysis reactivity. A hydrogen reactor utilizing hydraulic head pressure was developed. It generated hydrogen continuously for 1 h at a flow rate of 100 ml min -1 with hydrolysis of 5 g of tablet-form MgH 2 . The conversion yield was around 70%, regardless of the flow rate.

The MAP, M/G1,G2/1 queue with preemptive priority

Directory of Open Access Journals (Sweden)

Bong Dae Choi

1997-01-01

Full Text Available We consider the MAP, M/G1,G2/1 queue with preemptive resume priority, where low priority customers arrive to the system according to a Markovian arrival process (MAP and high priority customers according to a Poisson process. The service time density function of low (respectively: high priority customers is g1(x (respectively: g2(x. We use the supplementary variable method with Extended Laplace Transforms to obtain the joint transform of the number of customers in each priority queue, as well as the remaining service time for the customer in service in the steady state. We also derive the probability generating function for the number of customers of low (respectively, high priority in the system just after the service completion epochs for customers of low (respectively, high priority.

Luminescence Properties of Self-Activated Mm(VO4)2 (M = Mg, Ca, Sr, and Ba) Phosphors Synthesized by Solid-State Reaction Method.

Science.gov (United States)

Min, Xin; Huang, Zhaohui; Fang, Minghao; Liu, Yan'gai; Tang, Chao; Wu, Xiaowen

2016-04-01

In this paper, M3(VO4)2 (M = Mg, Ca, Sr, and Ba) self-activated phosphors were prepared by a solid-state reaction method at 1,000 °C for 5 h. The phase formation and micrographs were analyzed by X-ray diffraction and scanning electron microscopy. The Ca3(VO4)2 phosphor does not show any emission peaks under excitation with ultraviolet (UV) light. However, the M3(VO4)2 (M = Mg, Sr, and Ba) samples are effectively excited by UV light chips ranging from 200 nm to 400 nm and exhibit broad emission bands due to the charge transfer from the oxygen 2p orbital to the vacant 3d orbital of the vanadium in the VO4. The color of these phosphors changes from yellow to light blue via blue-green with increasing ionic radius from Mg to Sr to Ba. The luminescence lifetimes and quantum yield decrease with the increasing unit cell volume and V-V distance, in the order of Mg3(VO4)2 to Sr3(VO4)2 to Ba3(VO4)2. The emission intensity decreases with the increase of temperatures, but presents no color shift. This confirms that these self-activated M3(VO4)2 phosphors can be suggested as candidates of the single-phase phosphors for light using UV light emitting diodes (LEDs).

Ground state properties of neutron-rich Mg isotopes the "island of inversion" studied with laser and $\\beta$-NMR spectroscopy

CERN Document Server

Kowalska, M

2006-01-01

Studies in regions of the nuclear chart in which the model predictions of properties of nuclei fail can bring a better understanding of the strong interaction in the nuclear medium. To such regions belongs the so called "island of inversion" centered around Ne, Na and Mg isotopes with 20 neutrons in which unexpected ground-state spins, large deformations and dense low-energy spectra appear. This is a strong argument that the magic N=20 is not a closed shell in this area. In this thesis investigations of isotope shifts of stable $^{24-26}$Mg, as well as spins and magnetic moments of short-lived $^{29,31}$Mg are presented. The successful studies were performed at the ISOLDE facility at CERN using collinear laser and $\\beta$-NMR spectroscopy techniques. The isotopes were investigated as single-charged ions in the 280 nm transition from the atomic ground state $^2\\!$S$_{1/2}$ to one of the two lowest excited states $^2\\!$P$_{1/2 ,\\,3/2}$ using continuous wave laser beams. The isotope-shift measurements with fluor...

Inositol phosphates influence the membrane bound Ca2+/Mg2+ stimulated ATPase from human erythrocyte membranes

International Nuclear Information System (INIS)

Kester, M.; Ekholm, J.; Kumar, R.; Hanahan, D.J.

1986-01-01

The modulation by exogenous inositol phosphates of the membrane Ca 2+ /Mg 2+ ATPase from saponin/EGTA lysed human erythrocytes was determined in a buffer (pH 7.6) containing histidine, 80 mM, MgCl 2 , 3.3 mM, NaCl, 74 mM, KCl, 30 mM, Na 2 ATP, 2.3 mM, ouabain, 0.83 mM, with variable amounts of CaCl 2 and EGTA. The ATPase assay was linear with time at 44 0 C. The inositol phosphates were commercially obtained and were also prepared from 32 P labeled rabbit platelet inositol phospholipids. Inositol triphosphate (IP 3 ) elevated the Ca 2+ /Mg 2+ ATPase activity over basal levels in a dose, time, and calcium dependent manner and were increased up to 85% of control values. Activities for the Na + /K + -ATPase and a Mg 2+ ATPase were not effected by IP 3 . Ca 2+ /Mg 2+ APTase activity with IP 2 or IP 3 could be synergistically elevated with calmodulin addition. The activation of the ATPase with IP 3 was calcium dependent in a range from .001 to .02 mM. The apparent Km and Vmax values were determined for IP 3 stimulated Ca 2+ /Mg 2+ ATPase

New facilities for Al+MgF2 coating for 2-m class mirrors for UV

Science.gov (United States)

Zhupanov, Valery; Vlasenko, Oleg; Sachkov, Mikhail; Fedoseev, Viktor

2014-07-01

The World Space Observatory--Ultraviolet (WSO--UV) project is a Russian-Spanish space mission for spectroscopic and imaging observations in the UV domain (115-320 nm) where some of the most important astrophysical processes can be efficiently studied with unprecedented capability. In the horizon of the next decade, WSO--UV will be the only mission with the large primary mirror fully devoted for UV studies. The observatory includes a 170 cm aperture telescope capable of high-resolution spectroscopy, long slit low-resolution spectroscopy, and deep UV imaging. The telescope T-170M is a Ritchey-Chrétien with a F/10 focal ratio and a corrected field of view of 0.5 degrees. Specific data on the WSO-UV project (telescope, satellite, orbit, launcher, ground segment, etc.) are given in [1-6]. The current status of the WSO-UV focal plane instruments, their status of implementation, and the expected performances are presented in [7]. The science drivers of the WSO-UV mission are described in [8, 9]. The main WSO-UV instruments, spectrographs (WUVS instrument) and imagers (ISSIS instrument) are described in [10-13] and [14-15] correspondingly. The prospects of stellar studies with WSO-UV are presented in papers [16-17]. A paper [18] describes our experience of using the DP-190 glue for adhesive attachment of a large space mirror and its rim. In the instrument compartment, see Figure 1, the optical bench (OB) - used as reference plane for all the onboard instrumentation - is aligned and maintained in the correct position with respect to the primary mirror (PM) using a three rods system. An imaging instrument ISSIS is mounted on the upper basis of the optical bench, in the space available between the PM and the OB itself, while spectrographs (WUVS instrument) are mounted to the OB bottom basis. One of the primary tasks in creating telescope's PM is to apply coating with required reflective and protective properties. Aluminum is a well known reflecting coating for wavelength

47-mG2a: A Mouse IgG2a-Type of PcMab-47 Useful for Detecting Podocalyxin in Esophageal Cancers by Immunohistochemistry.

Science.gov (United States)

Kaneko, Mika K; Itai, Shunsuke; Yamada, Shinji; Kato, Yukinari

2018-04-09

Esophageal cancer is one of the highly malignant cancers. It comprises two of the most common histological tumor types: squamous cell carcinoma (SCC) and adenocarcinoma. SCC accounts for about 90% of esophageal cancers. Despite developments in treatment strategies, the prognosis and survival rate remain poor. Podocalyxin (PODXL) is a highly glycosylated type-I transmembrane protein. It is expressed in normal tissues such as kidney, heart, breast, and pancreas. Upregulation of PODXL correlates with tumor progression, invasion, and metastasis. Therefore, this glycoprotein could be a potential biomarker for predicting the prognosis of some cancers, for instance, brain, colorectal, oral, lung, bladder, prostate, and ovarian cancers. We previously developed a specific and sensitive anti-PODXL monoclonal antibody (mAb), PcMab-47 (mouse IgG 1 , kappa) and its mouse IgG 2a -type (47-mG 2a ). We showed their utility in immunohistochemical analysis of oral cancers. Herein, we demonstrate that PcMab-47 and 47-mG 2a can also be used to detect esophageal squamous cell carcinoma (ESCC) with this technique. These two antibodies, respectively, stained 123/130 (94.6%) and 127/130 (97.7%) ESCC cases, indicating that they can detect PODXL with high sensitivity in this carcinoma. Of more than 3+ cases, 47-mG 2a was more effective than PcMab-47, respectively, staining 56/127 (44.1%) and 41/123 (33.3%). Therefore, 47-mG 2a can be used for the detection of PODXL in ESCC using immunohistochemical analysis.

Measurements of the ground-state ionization energy and wavelengths for the 1snp {sup 1}P{sub 1}{sup *}-1s{sup 2} {sup 1}S{sub 0} (n=4-9) lines of Mg XI and F VIII

Energy Technology Data Exchange (ETDEWEB)

Pal' chikov, V.G. [Multicharged Ions Spectra Data Centre of VNIIFTRI, Mendeleevo (Russian Federation)). E-mail: vitpal@mail.ru; Ya Faenov, A.; Yu Skobelev, I. [Multicharged Ions Spectra Data Centre of VNIIFTRI, Mendeleevo (RU)] [and others

2002-06-28

The wavelengths of the 1snp {sup 1}P{sub 1}{sup 0}-1s{sup 2} {sup 1}S{sub 0} transitions in the He-like Mg XI (n = 4-9) and F VIII (n=4-8) have been measured in laser-produced plasmas. The accuracy of the present measurements (0.4-1.6 mA) is a large improvement over previous results. The Rydberg series is used to determine the ground-state ionization energy of F VIII and Mg XI: E{sub i}on (F VIII) 953.96{+-}0.11 eV, E{sub i}on (Mg XI)=1761.88{+-}0.15 eV. These experimental results are compared with theoretical data calculated by the 1/Z-expansion method and the HFR and MCDF approaches. Fairly good agreement between theory and experiment is observed with a precision up to 5x10{sup -5}. Radiative corrections to the 1s{sup 2} {sup 1}S{sub 0} state are analysed and compared with experiments. It is found that QED corrections to the ground-state ionization energy are significant at the present level of experimental accuracy. (author)

Hydrogen storage of Mg1−xMxH2 (M = Ti, V, Fe) studied using first-principles calculations

International Nuclear Information System (INIS)

Bhihi, M.; Lakhal, M.; Benyoussef, A.; El Kenz, A.; Labrim, H.; Mounkachi, O.; Hlil, E.K.

2012-01-01

In this work, the hydrogen storage properties of the Mg-based hydrides, i.e., Mg 1−x M x H 2 (M = Ti, V, Fe, 0 ≤ x ≤ 0.1), are studied using the Korringa—Kohn—Rostoker (KKR) calculation with the coherent potential approximation (CPA). In particular, the nature and concentrations of the alloying elements and their effects are studied. Moreover, the material's stability and hydrogen storage thermodynamic properties are discussed. In particular, we find that the stability and the temperature of desorption decrease without significantly affecting the storage capacities

Perovskites with noble metals of type Ba/sub 3/BM/sub 2/O/sub 9/; B = Mg, Fe, Co, Ni, Zn, Cd; M = Ru, Ir

Energy Technology Data Exchange (ETDEWEB)

Treiber, U; Kemmler-Sack, S; Ehmann, A [Tuebingen Univ. (Germany, F.R.). Lehrstuhl fuer Anorganische Chemie 2

1982-04-01

The perovskites Ba/sub 3/BM/sub 2/O/sub 9/ crystallize in a hexagonal BaTiO/sub 3/ structure and could be prepared for M = Ru; B = Mg, Fe, Co, Ni, Zn, Cd and M = Ir; B = Co, Ni. According to intensity calculations on powder data of Ba/sub 3/MgRu/sub 2/O/sub 9/ and Ba/sub 3/NiIr/sub 2/O/sub 9/ (refined intensity related R' value 6.7% (Ba/sub 3/MgRu/sub 2/O/sub 9/) and 6.9% (Ba/sub 3/NiIr/sub 2/O/sub 9/)) an 1:2 order is present and both lattices contain face connected M/sub 2/O/sub 9/ double octahedra linked by another via common corners through BO/sub 6/ single octahedra. The occurrence of this typ of cationic order results for B = Mg, Co, Ni, Zn, Cd from the analysis of the vibrational spectra. For B = Mg, Zn, Cd and presumable with B = Ni the charge distribution is B/sup 2 +// 2 M/sup 5 +/; for B = Co deviation can not be excluded. On the opposite in Ba/sub 3/FeRu/sub 2/O/sub 9/ an electron delocalisation is present.

Hydrogenation properties of Mg1-xM1xCu2 (M1=La and Nd) with larger interstitial sites than MgCu2

International Nuclear Information System (INIS)

Tsushio, Y.

1998-01-01

The hydrogenation properties of C15 compounds are controlled by crystal structure, the size of the interstitial hole being an especially important factor. Its effect on the hydrogenation properties of MgCu 2 substituted with rare earth elements of various radii is discussed and the limit in controlling the crystal structure by conventional substitution is explained. (orig.)

Superconductivity in dense Mg1–xMxB2 (M= Zr, Nb, Mo; x= 0⋅ 05 ...

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 28; Issue 3. Superconductivity in dense Mg1–MB2 (M = Zr, Nb, Mo; = 0.05) materials sintered under pressure. S Kalavathi C Divakar. Superconductors Volume 28 Issue 3 June 2005 pp 249-252 ...

Magnetic and dielectric properties of the ruthenium double perovskites La2MRuO6 (M=Mg, Co, Ni, and Zn)

International Nuclear Information System (INIS)

Yoshii, Kenji; Ikeda, Naoshi; Mizumaki, Masaichiro

2006-01-01

Magnetic and dielectric properties of the ruthenium double perovskites La 2 MRuO 6 (M=Mg, Co, Ni, and Zn) were investigated. The magnetization measurements for M=Co and Ni showed the existence of magnetic order at 20-30 K. Though the oxides with M=Zn and Mg exhibit a deviation from the Curie-Weiss law, magnetic order was not clearly observed. The result of La 2 ZnRuO 6 was different from that previously reported, in which a ferromagnetic transition was found at around 165 K. The AC dielectric measurements for M = Co and Ni showed large dielectric constants (typically larger than 1000) at around room temperature, suggesting both the formation of short-ranged polar regions and the magnetic origin of large dielectric constant. In addition, two peaks were found for the temperature dependence of the tan δ component for La 2 NiRuO 6 . The behavior suggests the existence of two different polar regions. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (Abstract Copyright [2006], Wiley Periodicals, Inc.)

Bulk and surface properties of magnesium peroxide MgO2

Science.gov (United States)

Esch, Tobit R.; Bredow, Thomas

2016-12-01

Magnesium peroxide has been identified in Mg/air batteries as an intermediate in the oxygen reduction reaction (ORR) [1]. It is assumed that MgO2 is involved in the solid-electrolyte interphase on the cathode surface. Therefore its structure and stability play a crucial role in the performance of Mg/air batteries. In this work we present a theoretical study of the bulk and low-index surface properties of MgO2. All methods give a good account of the experimental lattice parameters for MgO2 and MgO bulk. The reaction energies, enthalpies and free energies for MgO2 formation from MgO are compared among the different DFT methods and with the local MP2 method. A pronounced dependence from the applied functional is found. At variance with a previous theoretical study but in agreement with recent experiments we find that the MgO2 formation reaction is endothermic (HSE06-D3BJ: ΔH = 51.9 kJ/mol). The stability of low-index surfaces MgO2 (001) (Es = 0.96 J/m2) and (011) (Es = 1.98 J/m2) is calculated and compared to the surface energy of MgO (001). The formation energy of neutral oxygen vacancies in the topmost layer of the MgO2 (001) surface is calculated and compared with defect formation energies for MgO (001).

Defect structure of ultrafine MgB2 nanoparticles

International Nuclear Information System (INIS)

Bateni, Ali; Somer, Mehmet; Repp, Sergej; Erdem, Emre; Thomann, Ralf; Acar, Selçuk

2014-01-01

Defect structure of MgB 2 bulk and ultrafine particles, synthesized by solid state reaction route, have been investigated mainly by the aid of X-band electron paramagnetic resonance spectrometer. Two different amorphous Boron (B) precursors were used for the synthesis of MgB 2 , namely, boron 95 (purity 95%–97%, <1.5 μm) and nanoboron (purity >98.5%, <250 nm), which revealed bulk and nanosized MgB 2 , respectively. Scanning and transmission electron microscopy analysis demonstrate uniform and ultrafine morphology for nanosized MgB 2 in comparison with bulk MgB 2 . Powder X-ray diffraction data show that the concentration of the by-product MgO is significantly reduced when nanoboron is employed as precursor. It is observed that a significant average particle size reduction for MgB 2 can be achieved only by using B particles of micron or nano size. The origin and the role of defect centers were also investigated and the results proved that at nanoscale MgB 2 material contains Mg vacancies. Such vacancies influence the connectivity and the conductivity properties which are crucial for the superconductivity applications

Measurements of the ground-state ionization energy and wavelengths for the 1snp 1P1*-1s21S0 (n=4-9) lines of Mg XI and F VIII

International Nuclear Information System (INIS)

Pal'chikov, V.G.; Ya Faenov, A.; Yu Skobelev, I.

2002-01-01

The wavelengths of the 1snp 1 P 1 0 -1s 2 1 S 0 transitions in the He-like Mg XI (n = 4-9) and F VIII (n=4-8) have been measured in laser-produced plasmas. The accuracy of the present measurements (0.4-1.6 mA) is a large improvement over previous results. The Rydberg series is used to determine the ground-state ionization energy of F VIII and Mg XI: E i on (F VIII) 953.96±0.11 eV, E i on (Mg XI)=1761.88±0.15 eV. These experimental results are compared with theoretical data calculated by the 1/Z-expansion method and the HFR and MCDF approaches. Fairly good agreement between theory and experiment is observed with a precision up to 5x10 -5 . Radiative corrections to the 1s 2 1 S 0 state are analysed and compared with experiments. It is found that QED corrections to the ground-state ionization energy are significant at the present level of experimental accuracy. (author)

Structure of Na2O·MO·SiO2·CaF2 (M=Mg, Ca) oxyfluoride glasses

International Nuclear Information System (INIS)

Cheng Jinshu; Deng Wei; Wang Mitang

2012-01-01

(9-x)CaO·xMgO·15Na 2 O·60SiO 2 ·16CaF 2 (x=0, 2, 4, 6, and 9) oxyfluoride glasses were prepared. Utilizing the Raman scattering technique together with 29 Si and 19 F MAS NMR, the effect of alkaline metal oxides on the Q species of glass was characterized. Raman results show that as magnesia is added at the expense of calcium oxide, the disproportional reaction Q 3 →Q 4 +Q 2 (Q n is a SiO 4 tetrahedron with n bridging oxygens) prompted due to the high ionic field strength of magnesia, magnesium oxide entered into the silicate network as tetrahedral MgO 4 , and removed other modifying ions for charge compensation. This reaction was confirmed by 29 Si MAS NMR. 19 F MAS NMR results show that fluorine exists in the form of mixed calcium sodium fluoride species in all glasses and no Si-F bonds were formed. As CaO is gradually replaced by MgO (x=6, 9), a proportion of the magnesium ions combines with fluorine to form the MgF + species. Meanwhile, some part of Na + ions complex F - in the form of F-Na(6).

Isopiestic Investigation of the Osmotic and Activity Coefficients of {yMgCl2 + (1 - y)MgSO4}(aq) and the Osmotic Coefficients of Na2SO4.MgSO4(aq) at 298.15 K

Energy Technology Data Exchange (ETDEWEB)

Miladinovic, J; Ninkovic, R; Todorovic, M; Rard, J A

2007-06-06

Isopiestic vapor pressure measurements were made for {l_brace}yMgCl{sub 2} + (1-y)MgSO{sub 4}{r_brace}(aq) solutions with MgCl{sub 2} ionic strength fractions of y = 0, 0.1997, 0.3989, 0.5992, 0.8008, and (1) at the temperature 298.15 K, using KCl(aq) as the reference standard. These measurements for the mixtures cover the ionic strength range I = 0.9794 to 9.4318 mol {center_dot} kg{sup -1}. In addition, isopiestic measurements were made with NaCl(aq) as reference standard for mixtures of {l_brace}xNa{sub 2}SO{sub 4} + (1-x)MgSO{sub 4}{r_brace}(aq) with the molality fraction x = 0.50000 that correspond to solutions of the evaporite mineral bloedite (astrakanite), Na{sub 2}Mg(SO{sub 4}){sub 2} {center_dot} 4H{sub 2}O(cr). The total molalities, m{sub T} = m(Na{sub 2}SO{sub 4}) + m(MgSO{sub 4}), range from m{sub T} = 1.4479 to 4.4312 mol {center_dot} kg{sup -1} (I = 5.0677 to 15.509 mol {center_dot} kg{sup -1}), where the uppermost concentration is the highest oversaturation molality that could be achieved by isothermal evaporation of the solvent at 298.15 K. The parameters of an extended ion-interaction (Pitzer) model for MgCl2(aq) at 298.15 K, which were required for an analysis of the {l_brace}yMgCl{sub 2} + (1-y)MgSO{sub 4}{r_brace}(aq) mixture results, were evaluated up to I = 12.025 mol {center_dot} kg{sup -1} from published isopiestic data together with the six new osmotic coefficients obtained in this study. Osmotic coefficients of {l_brace}yMgCl{sub 2} + (1-y)MgSO{sub 4}{r_brace}(aq) solutions from the present study, along with critically-assessed values from previous studies, were used to evaluate the mixing parameters of the extended ion-interaction model.

Influence of particle size of Mg powder on the microstructure and critical currents of in situ powder-in-tube processed MgB_2 wires

International Nuclear Information System (INIS)

Kumakura, Hiroaki; Ye, Shujun; Matsumoto, Akiyoshi; Nitta, Ryuji

2016-01-01

We fabricated in situ powder-in-tube(PIT) MgB_2 wires using three kinds of Mg powders with particle size of ∼45 μm, ∼150 μm and 212∼600 μm. Mg particles were elongated to filamentary structure in the wires during cold drawing process. Especially, long Mg filamentary structure was obtained for large Mg particle size of 212∼600 μm. Critical current density, J_c, increased with increasing Mg particle size for 1 mm diameter wires. This is due to the development of filamentary structure of high density MgB_2 superconducting layer along the wires. This MgB_2 structure is similar to that of the internal Mg diffusion (IMD) processed MgB_2 wires. However, J_c of the wires fabricated with 212∼600 μm Mg particle size decreased and the scattering of J_c increased with decreasing wire diameter, while the J_c of the wires with ∼45 μm Mg particle was almost independent of the wire diameter. The cross sectional area reduction of the Mg particles during the wire drawing is smaller than that of the wire. When using large size Mg particle, the number of Mg filaments in the wire cross section is small. These two facts statistically lead to the larger scattering of Mg areal fraction in the wire cross section with proceeding of wire drawing process, resulting in smaller volume fraction of MgB_2 in the wire and lower J_c with larger scattering along the wire. SiC nano powder addition is effective in increasing J_c for all Mg particle sizes. (author)

New intermetallic MIrP (M=Ti, Zr, Nb, Mo) and MgRuP compounds related with MoM'P (M'=Ni and Ru) superconductor

Science.gov (United States)

Kito, Hijiri; Iyo, Akira; Wada, Toshimi

2011-01-01

Using a cubic-anvil high-pressure apparatus, ternary iridium phosphides MIrP (M=Ti, Zr, Nb, Mo) and MgRuP have been prepared by reaction of stoichiometric amounts of each metal and phosphide powders at around 2 Gpa and above 1523 K for the first time. The structure of these compounds prepared at high-pressure has been characterized by X-ray powder diffraction. Diffraction lines of these compounds are assigned by the index of the Co2Si-type structure. The electrical resistivity and the d.c magnetic susceptibility of MIrP (M=Ti, Zr, Nb, Mo) have measured at low temperatures. Unfortunately, no superconducting transition for MIrP (M=Ti, Zr, Nb, Mo) and MgRuP are observed down to 2 K.

New intermetallic MIrP (M=Ti, Zr, Nb, Mo) and MgRuP compounds related with MoM'P (M'=Ni and Ru) superconductor

International Nuclear Information System (INIS)

Kito, Hijiri; Iyo, Akira; Wada, Toshimi

2011-01-01

Using a cubic-anvil high-pressure apparatus, ternary iridium phosphides MIrP (M=Ti, Zr, Nb, Mo) and MgRuP have been prepared by reaction of stoichiometric amounts of each metal and phosphide powders at around 2 Gpa and above 1523 K for the first time. The structure of these compounds prepared at high-pressure has been characterized by X-ray powder diffraction. Diffraction lines of these compounds are assigned by the index of the Co 2 Si-type structure. The electrical resistivity and the d.c magnetic susceptibility of MIrP (M=Ti, Zr, Nb, Mo) have measured at low temperatures. Unfortunately, no superconducting transition for MIrP (M=Ti, Zr, Nb, Mo) and MgRuP are observed down to 2 K.

Proteome of Salmonella enterica serotype Tyhimurium Grown in Low Mg2+/pH Medium

Energy Technology Data Exchange (ETDEWEB)

Shi, Liang; Ansong, Charles; Smallwood, Heather S.; Rommereim, Leah M.; McDermott, Jason E.; Brewer, Heather M.; Norbeck, Angela D.; Taylor, Ronald C.; Gustin, Jean K.; Heffron, Fred; Smith, Richard D.; Adkins, Joshua N.

2009-09-04

To determine the impact of a low Mg2+/pH defined growth medium (MgM) on the proteome of Salmonella enterica serotype Typhimurium, we cultured S. Typhimurium cells in the medium under two different conditions termed MgM Shock and MgM Dilution and then comparatively analyzed the bacterial cells harvested from these conditions by a global proteomic approach. Proteomic results showed that MgM Shock and MgM Dilution differentially affected the S. Typhimurium proteome. MgM Shock induced a group of proteins whose induction usually occurred at low O2 level, while MgM Dilution induced those related to the type III secretion system (T3SS) of Salmonella Pathogenicity Island 2 (SPI2) and those involved in thiamine or biotin biosynthesis. The metabolic state of the S. Typhimurium cells grown under MgM Shock condition also differed significantly from that under MgM Dilution condition. Western blot analysis not only confirmed the proteomic results, but also showed that the abundances of SPI2-T3SS proteins SsaQ and SseE and biotin biosynthesis proteins BioB and BioD increased after S. Typhimurium infection of RAW 264.7 macrophages. Deletion of the gene encoding BioB reduced the bacterial ability to replicate inside the macrophages, suggesting a biotin-limited environment encountered by S. Typhimurium within RAW 264.7 macrophages.

Structural features of AgCaCdMg2(PO4)3 and AgCd2Mg2(PO4)3, two new compounds with the alluaudite-type structure, and their catalytic activity in butan-2-ol conversion

International Nuclear Information System (INIS)

Kacimi, Mohammed; Ziyad, Mahfoud; Hatert, Frederic

2005-01-01

AgCaCdMg 2 (PO 4 ) 3 and AgCd 2 Mg 2 (PO 4 ) 3 , two new compounds with the alluaudite-type structure, were synthesized by a solid state reaction in air at 750 deg. C. The X-ray powder diffraction pattern of AgCaCdMg 2 (PO 4 ) 3 indicates the presence of small amounts of (Ca, Mg) 3 (PO 4 ) 2 with the whitlockite structure, as impurity, whereas AgCd 2 Mg 2 (PO 4 ) 3 is constituted by pure alluaudite. The Rietveld refinements of the X-ray powder diffraction patterns indicate an ordered cationic distribution for AgCd 2 Mg 2 (PO 4 ) 3 , with Ag on A(2)', Cd on A(1) and M(1), and Mg on M(2), whereas a disordered distribution of Cd and Ca between the A(1) and M(1) sites is observed for AgCaCdMg 2 (PO 4 ) 3 . The catalytic properties of these compounds has been measured in reaction of butan-2-ol dehydrogenation. In the absence of oxygen, both samples exhibit poor dehydrogenation activity. All samples displayed no dehydration activity. Introduction of oxygen into the feed changed totally the catalytic behavior of the catalysts. The production of methyl ethyl ketone increases with time on stream and the reaction temperature. AgCaCdMg 2 (PO 4 ) 3 is more efficient than AgCd 2 Mg 2 (PO 4 ) 3

Fabrication of sandwich-type MgB{sub 2}/Boron/MgB{sub 2} Josephson junctions with rapid annealing method

Energy Technology Data Exchange (ETDEWEB)

Zhang, Song; Wang, Xu; Ma, Junli; Cui, Ruirui; Deng, Chaoyong, E-mail: cydeng@gzu.edu.cn

2015-11-15

Sandwich-type MgB{sub 2}/Boron/MgB{sub 2} Josephson junctions were fabricated using magnetron sputtering system. The rapid-anneal process was adopted to replace traditional way of annealing, trying to solve the problem of interdiffusion and oxidation with multilayer films. The boron film was used as barrier layer to avoid the introduction of impurities and improve reproducibility of the junctions. The bottom MgB{sub 2} thin films deposited on c-plane sapphire substrate exhibits a critical temperature T{sub C} of 37.5 K and critical current density J{sub C} at 5 K of 8.7 × 10{sup 6} A cm{sup −2}. From the XRD pattern, the bottom MgB{sub 2} thin film shows c-axis orientation, whereas the top MgB{sub 2} became polycrystalline as Boron barrier layer grown thicker. Therefore, all junction samples show lower T{sub C} than single MgB{sub 2} thin film. The junctions exhibit excellent quasiparticle characteristics with ideal dependence on temperature and Boron barrier thickness. Subharmonic gap structure was appeared in conductance characteristics, which was attributed to the multiple Andreev reflections (MAR). The result demonstrates great promise of this new fabrication technology for MgB{sub 2} Josephson junction fabrication. - Highlights: • Sandwich-type MgB{sub 2}/Boron/MgB{sub 2} Josephson junctions were fabricated. • The junctions were annealed after deposition with the rapid-anneal process. • The highest critical current is 25.3 mA at 5 K and remains non-zero near 25 K. • Subharmonic gap features can be observed in the dI/dV – V curves.

Durability of ITO-MgF2 Films for Space-Inflatable Polymer Structures

Science.gov (United States)

Kerslake, Thomas W.; Waters, Deborah L.; Schieman, David A.; Hambourger, Paul D.

2003-01-01

This paper presents results from ITO-MgF2 film durability evaluations that included tape peel, fold, thermal cycle, and AO exposure testing. Polymer coupon preparation is described as well as ITO-MgF2 film deposition equipment, procedures and film characterization. Durability testing methods are also described. The pre- and post-test condition of the films is assessed visually, microscopically, and electrically. Results show that at 500 ITO - 9 vol% MgF2 film is suitable to protect polymer surfaces, such as those used in space-inflatable structures of the PowerSphere microsatellite concept, during a 1-year Earth orbiting mission. Future plans for ground-based and orbital testing of this film are also discussed.

Nanocrystalline spinel ferrite (MFe2O4, M = Ni, Co, Mn, Mg, Zn) powders prepared by a simple aloe vera plant-extracted solution hydrothermal route

International Nuclear Information System (INIS)

Phumying, Santi; Labuayai, Sarawuth; Swatsitang, Ekaphan; Amornkitbamrung, Vittaya; Maensiri, Santi

2013-01-01

Graphical abstract: This figure shows the specific magnetization curves of the as-prepared MFe 2 O 4 (M = Ni, Co, Mn, Mg, Zn) powders obtained from room temperature VSM measurement. These curves are typical for a soft magnetic material and indicate hysteresis ferromagnetism in the field ranges of ±500 Oe, ±1000 Oe, and ±2000 Oe for the CoFe 2 O 4 , MgFe 2 O 4 and MnFe 2 O 4 respectively, whereas the samples of NiFe 2 O 4 and ZnFe 2 O 4 show a superparamagnetic behavior. Highlights: ► Nanocrystalline MFe 2 O 4 powders were synthesized by a novel hydrothermal method. ► Metal acetylacetonates and aloe vera plant-extracted solution are used. ► This biosynthetic route is very simple and provides high-yield oxide nanomaterials. ► XRD and TEM results indicate that the prepared samples have only spinel structure. ► The maximum M s of 68.9 emu/g at 10 kOe were observed for the samples of MnFe 2 O 4 . - Abstract: Nanocrystalline spinel ferrite MFe 2 O 4 (M = Ni, Co, Mn, Mg, Zn) powders were synthesized by a novel hydrothermal method using Fe(acac) 3 , M(acac) 3 (M = Ni, Co, Mn, Mg, Zn) and aloe vera plant extracted solution. The X-ray diffraction and selected-area electron diffraction results indicate that the synthesized nanocrystalline have only spinel structure without the presence of other phase impurities. The crystal structure and morphology of the spinel ferrite powders, as revealed by TEM, show that the NiFe 2 O 4 and CoFe 2 O 4 samples contain nanoparticles, whereas the MnFe 2 O 4 and MgFe 2 O 4 samples consist of many nanoplatelets and nanoparticles. Interestingly, the ZnFe 2 O 4 sample contains plate-like structure of networked nanocrystalline particles. Room temperature magnetization results show a ferromagnetic behavior of the CoFe 2 O 4 , MnFe 2 O 4 and MgFe 2 O 4 samples, whereas the samples of NiFe 2 O 4 and ZnFe 2 O 4 exhibit a superparamagnetic behavior

Electrical properties and structure of glasses in the Ba(PO3)2-MF2 systems, where M = Mg, Ca, Sr, Ba

International Nuclear Information System (INIS)

Sokolov, I.A.; Tarlakov, Yu.P.; Murin, I.V.; Pronkin, A.A.

2000-01-01

Using the methods of conductometry and IR spectroscopy the concentrational dependences of electric conductivity are studied, the nature of current carriers is determined, the concentrational dependence of transfer numbers is ascertained and structural changes in glasses of the system Ba(PO 3 ) 2 -MF 2 (M = Mg, Ca, Sr, Ba), depending on MF 2 content, are considered. It is shown that F - ions take part in electric current transfer. Influence of crystallochemical nature of alkaline-earth cations on physicochemical properties and structure of the glasses studied is analyzed [ru

50 K anomalies in superconducting MgB{sub 2} wires in copper and silver tubes

Energy Technology Data Exchange (ETDEWEB)

Majoros, M [Interdisciplinary Research Centre in Superconductivity, University of Cambridge, Cambridge (United Kingdom); Glowacki, B A [Interdisciplinary Research Centre in Superconductivity, University of Cambridge, Cambridge (United Kingdom); Department of Materials Science and Metallurgy, University of Cambridge, Cambridge (United Kingdom); Vickers, M E [Department of Materials Science and Metallurgy, University of Cambridge, Cambridge (United Kingdom)

2002-02-01

In situ and ex situ MgB{sub 2} wires were prepared by the powder-in-tube method. Copper and silver tubes were used as a cladding material. AC susceptibility measurements revealed a small anomalous decrease with onset around 50 K. This effect persisted also when the wires were ground into powders. Electron microscopy and x-ray studies were performed on copper clad samples. Spectroscopic measurements in a SEM showed that regions contained either Cu or Mg and B. X-ray diffraction gave the major crystalline phases as Cu, MgCu{sub 2} and MgB{sub 2}. Diffraction evidence for Cu substituting in the Mg position was inconclusive. (author)

ß-Adrenergic Stimulation Increases RyR2 Activity via Intracellular Ca2+ and Mg2+ Regulation

Science.gov (United States)

Li, Jiao; Imtiaz, Mohammad S.; Beard, Nicole A.; Dulhunty, Angela F.; Thorne, Rick; vanHelden, Dirk F.; Laver, Derek R.

2013-01-01

Here we investigate how ß-adrenergic stimulation of the heart alters regulation of ryanodine receptors (RyRs) by intracellular Ca2+ and Mg2+ and the role of these changes in SR Ca2+ release. RyRs were isolated from rat hearts, perfused in a Langendorff apparatus for 5 min and subject to 1 min perfusion with 1 µM isoproterenol or without (control) and snap frozen in liquid N2 to capture their phosphorylation state. Western Blots show that RyR2 phosphorylation was increased by isoproterenol, confirming that RyR2 were subject to normal ß-adrenergic signaling. Under basal conditions, S2808 and S2814 had phosphorylation levels of 69% and 15%, respectively. These levels were increased to 83% and 60%, respectively, after 60 s of ß-adrenergic stimulation consistent with other reports that ß-adrenergic stimulation of the heart can phosphorylate RyRs at specific residues including S2808 and S2814 causing an increase in RyR activity. At cytoplasmic [Ca2+] adrenergic stimulation increased luminal Ca2+ activation of single RyR channels, decreased luminal Mg2+ inhibition and decreased inhibition of RyRs by mM cytoplasmic Mg2+. At cytoplasmic [Ca2+] >1 µM, ß-adrenergic stimulation only decreased cytoplasmic Mg2+ and Ca2+ inhibition of RyRs. The Ka and maximum levels of cytoplasmic Ca2+ activation site were not affected by ß-adrenergic stimulation. Our RyR2 gating model was fitted to the single channel data. It predicted that in diastole, ß-adrenergic stimulation is mediated by 1) increasing the activating potency of Ca2+ binding to the luminal Ca2+ site and decreasing its affinity for luminal Mg2+ and 2) decreasing affinity of the low-affinity Ca2+/Mg2+ cytoplasmic inhibition site. However in systole, ß-adrenergic stimulation is mediated mainly by the latter. PMID:23533585

Measurements of CO2 Column Abundance in the Low Atmosphere Using Ground Based 1.6 μm CO2 DIAL

Science.gov (United States)

Abo, M.; Shibata, Y.; Nagasawa, C.

2017-12-01

Changes in atmospheric carbon dioxide (CO2) concentration are believed to produce the largest radiative forcing for the current climate system. Accurate predictions of atmospheric CO2 concentration rely on the knowledge of its sinks and sources, transports, and its variability with time. Although this knowledge is currently unsatisfactory, numerical models use it as a way in simulating CO2 fluxes. Validating and improving the global atmospheric transport model, therefore, requires precise measurement of the CO2 concentration profile. There are two further variations on Lidar: the differential absorption Lidar (DIAL) and the integrated path differential absorption (IPDA) Lidar. DIAL/IPDA are basically for profile/total column measurement, respectively. IPDA is a special case of DIAL and can measure the total column-averaged mixing ratio of trace gases using return signals from the Earth's surface or from thick clouds based on an airborne or a satellite. We have developed a ground based 1.6 μm DIAL to measure vertical CO2 mixing ratio profiles from 0.4 to 2.5 km altitude. The goals of the CO2 DIAL are to produce atmospheric CO2 mixing ratio measurements with much smaller seasonal and diurnal biases from the ground surface. But, in the ground based lidar, return signals from around ground surface are usually suppressed in order to handle the large dynamic range. To receive the return signals as near as possible from ground surface, namely, the field of view (FOV) of the telescope must be wide enough to reduce the blind range of the lidar. While the return signals from the far distance are very weak, to enhance the sensitivity and heighten the detecting distance, the FOV must be narrow enough to suppress the sky background light, especially during the daytime measurements. To solve this problem, we propose a total column measurement method from the ground surface to 0.4 km altitude. Instead of strong signals from thick clouds such as the IPDA, the proposed method uses

Population pharmacokinetics of oxaliplatin (85 mg/m(2)) in combination with 5-fluorouracil in patients with advanced colorectal cancer

NARCIS (Netherlands)

Kho, Y.H.; Jansman, F.G.A.; Prins, N.H.; Neef, C.; Brouwers, J.R.B.J.

Pharmacokinetic (PK) studies of oxaliplatin, using a dose regimen of 85mg/m(2) are lacking. A PK model may be used in future studies to investigate the relationship between pharmacokinetics and dose limiting toxicity. The purpose of this study was to construct a population PK model to describe

Stability of 2 mg/mL Adenosine Solution in Polyvinyl Chloride and Polyolefin Infusion Bags.

Science.gov (United States)

DeAngelis, Michael; Ferrara, Alexander; Gregory, Kaleigh; Zammit, Kimberly; Zhao, Fang

2018-04-01

Adenosine is a potent endogenous mediator of vasodilation. Compounded sterile solutions of adenosine are used in cardiac catheterization lab to perform stress tests on the heart. These tests are used to determine the fractional flow reserve (FFR) and are commonly used in the management and diagnosis of cardiovascular conditions. The purpose of this study was to assess the physical and chemical stability of 2 mg/mL adenosine in 0.9% Sodium Chloride Injection, USP in polyvinyl chloride [PVC]) and polyolefin infusion bags stored at room temperature (20°C-25°C) and under refrigeration (2°C-8°C). The compounding and analytical methods used in this study were very similar to those described in the prior publications from the authors' laboratory. To ensure a uniform starting concentration of all stability samples, a batch of 2 mg/mL adenosine solution was prepared and then packaged into empty PVC and polyolefin infusion bags. These stability samples were prepared in triplicate for each bag type and storage temperature (a total of 12 samples). The infusion bag samples were assessed for stability immediately after preparation and after 1 day, 3 days, 7 days, and 14 days. At each time point, the infusion bags were first visually inspected against a light background for color change, clarity, and particulates. Aliquots were drawn from each sample at each time point for pH analysis and high-performance liquid chromatography (HPLC) analysis. Over 14 days of storage at room temperature or refrigeration, no considerable change in visual appearance or pH was observed in any bags. All samples retained 90% to 110% of the initial drug concentration. No significant degradation peaks were observed in the HPLC chromatograms.

Effect of metal ion and ball milling on the electrochemical properties of M0.5TiOPO4 (M = Ni, Cu, Mg)

International Nuclear Information System (INIS)

Godbole, Vikram A.; Villevieille, Claire; Novák, Petr

2013-01-01

Various metal titanium oxyphosphates, M 0.5 TiOPO 4 (M = Ni, Cu, Mg) were synthesized via modified solution route synthesis. The as synthesized M 0.5 TiOPO 4 (M = Ni, Cu, Mg) were electrochemically tested using galvanostatic cycling, cyclic voltammetry, and rate performance measurements in order to investigate the effect of metal ion (M) on the electrochemical performance of this family of materials. All the studied materials reacted with 3 Li + during the 1st lithiation showing reaction plateaus at different potentials versus Lithium. Similar studies were performed on M 0.5 TiOPO 4 (M = Ni, Cu, Mg) samples with smaller particle size, obtained via ball milling, in order to understand the effect of particle size on the electrochemistry of the materials. The ball milled samples delivered higher specific charge during the 1st cycle showing reaction plateaus at different potentials, poorer capacity retention, and poorer rate capability as compared to the as synthesized ones. This was attributed to a change in morphology and particle size of the samples upon ball milling. Amongst all the tested materials, the as synthesized Cu 0.5 TiOPO 4 showed the best electrochemistry. The ball milled Mg 0.5 TiOPO 4 reacted with ∼5.5 Li + during 1st lithiation (as compared to 3 Li + expected from this family of compounds) and 3.3 Li + during the 1st delithiation (rather than the expected 2 Li + ). This suggests a reaction mechanism where Mg 0.5 TiOPO 4 undergoes a phase transformation forming Mg 0 , which reversibly alloys with 2.5 extra Li + . Thus the electrochemical cycling of Mg 0.5 TiOPO 4 gives insights into the reaction mechanism in this family of materials

[Effect of M007 mediated photodynamic therapy on proliferation of human osteosarcoma MG63 cells in vitro].

Science.gov (United States)

Zhou, Yu-Kai; Wu, Wen-Zhi; Zhang, Lan; Yang, Chun-Hui; Wang, Yan-Ping

2012-01-01

To investigate the effect of a new photosensitizer, M007 mediated photodynamic therapy on proliferation of human osteosarcoma MG63 cells in vitro. Human osteosarcoma MG63 cells were prepared as 1 x 10(6) /mL single-cell suspension, and 1 mL cells were transferred into 60 mL culture dish, then treated with 5 different gradient dosages (0, 2, 4, 8, 16 micromol/L) of M007 followed by photodynamic therapy or dark reaction for 10 min. The survival rate of the cells and the mode of cell death were detected by flow cytometry with the stain of Annexin V-FITC/PI. The effect on proliferation of survival cells was observed by MTT assay and colony-forming assay. M007 mediated photodynamic therapy induced the inactivation of MG63 human osteosarcoma cells in the way of late apoptosis/necrosis or becoming naked nucleus predominately. More than 90% MG63 cells in M007-PDT group were dead under the treatment of 2-16 micromol/L M007. The survival rates of 4-16 micromol/L M007-PDT group were steadily less than 1%. The optical densities did not increase with extension of culture time in 2-8 micromol/L M007-PDT group (P > 0.05). There were 16 survival alive cells found occasionally in 2 micromol/L M007-PDT group, but no colonies found in other groups. M007 mediated photodynamic therapy totally inactivated human osteosarcoma MG63 cells in vitro with the dosage more than 4 micromol/L.

Phase I dose-escalation study to examine the safety and tolerability of LY2603618, a checkpoint 1 kinase inhibitor, administered 1 day after pemetrexed 500 mg/m(2) every 21 days in patients with cancer.

Science.gov (United States)

Weiss, Glen J; Donehower, Ross C; Iyengar, Tara; Ramanathan, Ramesh K; Lewandowski, Karen; Westin, Eric; Hurt, Karla; Hynes, Scott M; Anthony, Stephen P; McKane, Scott

2013-02-01

This phase I study aims at assessing the safety and tolerability of LY2603618, a selective inhibitor of Checkpoint Kinase 1, in combination with pemetrexed and determining the maximum tolerable dose and the pharmacokinetic parameters. This was an open-label, multicenter, dose-escalation study in patients with advanced solid tumors. Increasing doses of LY2603618 (40-195 mg/m(2)) were combined with 500 mg/m(2) of pemetrexed. LY2603618 was administered on Days 1 and 9 and pemetrexed on Day 8 in a 28-day cycle. For all subsequent 21-day cycles, pemetrexed was administered on Day 1 and LY2603618 on Day 2. Antitumor activity was evaluated as per Response Evaluation Criteria in Solid Tumors 1.0. A total of 31 patients were enrolled into six cohorts (three at 40 mg/m(2) over 4.5-hour infusion, 1-hour infusion in subsequent cohorts: three each at 40 mg/m(2), 70 mg/m(2), and 195 mg/m(2); 13 at 105 mg/m(2); six at 150 mg/m(2)). Four patients experienced a dose-limiting toxicity: diarrhea (105 mg/m(2)); reversible infusion-related reaction (150 mg/m(2)); thrombocytopenia (195 mg/m(2)); and fatigue (195 mg/m(2)). The maximum tolerated dose was defined as 150 mg/m(2). The pharmacokinetic data demonstrated that the exposure of LY2603618 increased in a dose-dependent manner, displayed a suitable half-life for maintaining required human exposures while minimizing the intra- and inter-cycle accumulation, and was unaffected by the pemetrexed administration. The pharmacokinetic-defined biologically efficacious dose was achieved at doses ≥105 mg/m(2). LY2603618 administered approximately 24 h after pemetrexed showed acceptable safety and pharmacokinetic profiles.

Superconducting tunnel junctions on MgB{sub 2} using MgO and CaF{sub 2} as a barrier

Energy Technology Data Exchange (ETDEWEB)

Sakoda, Masahito, E-mail: sakoda@cc.tuat.ac.jp [Department of Applied Physics, Tokyo University of Agriculture and Technology, 2-24-16, Koganei, Tokyo 184-8588 (Japan); Aibara, Masato; Mede, Kazuya; Kikuchi, Motoyuki; Naito, Michio [Department of Applied Physics, Tokyo University of Agriculture and Technology, 2-24-16, Koganei, Tokyo 184-8588 (Japan)

2016-11-15

Highlights: • We have revised the manuscript according to reviewer's comments. The details are in “Response to Reviewers”. • Superconducting junctions with MgO and CaF{sub 2} barrier were fabricated in order to improve the quality of junctions. • In SIN junctions with MgO barrier, clear superconducting gap was observed. (). • In SIS junctions with CaF2 barrier, Josephson current was observed over 30 K. (). • The compatibility of each barrier material at the upper and lower interfaces was clarified. (). - Abstract: We report the fabrication of superconducting tunnel junctions, both of superconductor–insulator-normal metal (SIN) and superconductor–insulator-superconductor (SIS), on MgB{sub 2} using MgO and CaF{sub 2} as a barrier. The SIN junctions fabricated using an MgO barrier showed excellent quasi-particle characteristics, including a large superconducting gap (Δ) of 2.5–3 meV and a low zero-bias conductance. We have also fabricated SIS junctions with an MgO barrier, but the quasi-particle characteristics of the SIS junctions are not as good as those of the SIN junctions, namely a reduced superconducting gap and a high zero-bias conductance. It appears that top MgB{sub 2} electrodes do not grow well on an MgO barrier, which is also suggested from in-situ RHEED observation. The SIN junctions fabricated using a CaF{sub 2} barrier showed less sharp quasi-particle characteristics than using an MgO barrier. However, the SIS junctions using a CaF{sub 2} barrier showed a fairly large I{sub c}R{sub N} value at 4.2 K over 1 mV and also exhibited finite Josephson current up to almost the film's T{sub c} (∼30 K). The RHEED observation revealed that top MgB{sub 2} electrodes grow well on a CaF{sub 2} barrier.

Relativistic quasiparticle band structures of Mg2Si, Mg2Ge, and Mg2Sn: Consistent parameterization and prediction of Seebeck coefficients

Science.gov (United States)

Shi, Guangsha; Kioupakis, Emmanouil

2018-02-01

We apply density functional and many-body perturbation theory calculations to consistently determine and parameterize the relativistic quasiparticle band structures of Mg2Si, Mg2Ge, and Mg2Sn, and predict the Seebeck coefficient as a function of doping and temperature. The quasiparticle band gaps, including spin-orbit coupling effects, are determined to be 0.728 eV, 0.555 eV, and 0.142 eV for Mg2Si, Mg2Ge, and Mg2Sn, respectively. The inclusion of the semicore electrons of Mg, Ge, and Sn in the valence is found to be important for the accurate determination of the band gaps of Mg2Ge and Mg2Sn. We also developed a Luttinger-Kohn Hamiltonian and determined a set of band parameters to model the near-edge relativistic quasiparticle band structure consistently for all three compounds that can be applied for thermoelectric device simulations. Our calculated values for the Seebeck coefficient of all three compounds are in good agreement with the available experimental data for a broad range of temperatures and carrier concentrations. Our results indicate that quasiparticle corrections are necessary for the accurate determination of Seebeck coefficients at high temperatures at which bipolar transport becomes important.

Synthesis and mechanical properties of stabilized zirconia ceramics: MgO-ZrO_2 and Y_2O_3-MgO- ZrO_2

International Nuclear Information System (INIS)

Yamagata, C.; Mello-Castanho, S.R.H.; Paschoal, J.O.A.

2014-01-01

Precursor MgO-ZrO_2 and Y_2O_3-MgO-ZrO_2 ceramic powders were synthesized by the method of co-precipitation and characterized by techniques such as laser diffraction, QELS (Quasi Elastic Light Scattering), XRD, BET, and SEM. Nanoscale powders with specific surface area higher than 60 m"2. g"-"1 was achieved. Sintered ceramic obtained from the synthesized powders, were characterized to mechanical tests using Vickers indentation technique. The addition of Y_2O_3 promoted an increase in hardness of the ceramics and total cubic crystalline phase stabilization. (author)

Formation of long-period stacking ordered structures in Mg88M5Y7 (M = Ti, Ni and Pb) casting alloys

International Nuclear Information System (INIS)

Jin, Qian-Qian; Fang, Can-Feng; Mi, Shao-Bo

2013-01-01

Highlights: •Apart from 18R-LPSO, 14H-LPSO structure was determined in the Mg-Ni-Y alloys. •The appearance of twin-related structure in 18R-LPSO structure results from the stacking faults in the stacking sequence of the closely packed planes. •A new (Pb, Mg) 2 Y phase with a body-centered orthorhombic structure was determined in the Mg-Pb-Y alloy. •No LPSO structures were found in the Mg-Pb-Y and Mg-Ti-Y casting alloys. -- Abstract: Formation of long-period stacking ordered (LPSO) structures is investigated in Mg 88 M 5 Y 7 (M = Ti, Ni and Pb) casting alloys by means of electron microscopy and X-ray diffraction. In the Mg 88 Ni 5 Y 7 casting alloy, 14H-LPSO structure is observed in a small amount, which coexists with 18R-LPSO structure. The appearance of stacking faults in 18R-LPSO structure results in twin-related structure in the stacking sequence of the closely packed planes. A new (Pb, Mg) 2 Y phase with a body-centered orthorhombic structure is determined in the Mg 88 Pb 5 Y 7 alloy. No LPSO structures are found in the Mg 88 Pb 5 Y 7 and Mg 88 Ti 5 Y 7 casting alloys. In terms of the atomic radius and heat of mixing, the formation ability of LPSO structure in the present alloys is discussed

Fracture toughness of MgCr2O4-ZrO2 composities

International Nuclear Information System (INIS)

Singh, J.P.

1985-01-01

The effect of unstabilized ZrO 2 inclusions on the fracture surface energy of MgCr 2 O 4 was studied as a function of ZrO 2 content. It was observed that fracture surface energy increases with increasing ZrO 2 content, and reaches the maximum value of 24.5 j/m 2 at 16.5 vol% ZrO 2 . This represents an approx. = fourhold increase in the fracture surface energy of Mg 2 O 4 as a result of ZrO 2 inclusions. It is proposed that this improvement results from the energy absorbed by the microcracks formed in the MgCr 2 O 4 matrix as a result of the tetragonal → monoclinic phase transormation of ZrO 2 and the associated volume expansion

Structurally characterized 1,1,3,3-tetramethylguanidine solvated magnesium aryloxide complexes: [Mg(mu-OEt)(DBP)(H-TMG)]2, [Mg(mu-OBc)(DBP)(H-TMG)]2, [Mg(mu-TMBA)(DBP)(H-TMG)]2, [Mg(mu-DPP)(DBP)(H-TMG)]2, [Mg(BMP)2(H-TMG)2], [Mg(O-2,6-Ph2C6H3)2 (H-TMG)2].

Science.gov (United States)

Monegan, Jessie D; Bunge, Scott D

2009-04-06

The synthesis and structural characterization of several 1,1,3,3-tetramethylguanidine (H-TMG) solvated magnesium aryloxide complexes are reported. Bu(2)Mg was successfully reacted with H-TMG, HOC(6)H(3)(CMe(3))(2)-2,6 (H-DBP), and either ethanol, a carboxylic acid, or diphenyl phosphate in a 1:1 ratio to yield the corresponding [Mg(mu-L)(DBP)(H-TMG)](2) where L = OCH(2)CH(3) (OEt, 1), O(2)CC(CH(3))(3) (OBc, 2), O(2)C(C(6)H(2)-2,4,6-(CH(3))(3)) (TMBA, 3), or O(2)P(OC(6)H(5))(2) (DPP, 4). Bu(2)Mg was also reacted with two equivalents of H-TMG and HOC(6)H(3)(CMe(3))-2-(CH(3))-6 (BMP) or HO-2,6-Ph(2)C(6)H(3) to yield [Mg(BMP)(2)(H-TMG)(2)] (5) and [Mg(O-2,6-Ph(2)C(6)H(3))(2)(H-TMG)(2)] (6). Compounds 1-6 were characterized by single-crystal X-ray diffraction. Polymerization of l- and rac-lactide with 1 was found to generate polylactide (PLA). A discussion concerning the relevance of compounds 2 - 4 to the structure of Mg-activated phosphatase enzymes is also provided. The bulk powders for all complexes were found to be in agreement with the crystal structures based on elemental analyses, FT-IR spectroscopy, and (1)H, (13)C and (31)P NMR studies.

Second-line chemotherapy of disseminated malignant melanoma with cystemustine at 60 mg/m2: a phase II trial.

Science.gov (United States)

Thivat, Emilie; Durando, Xavier; D'Incan, Michel; Cure, Hervé; Mouret-Reynier, Marie-Ange; Madelmont, Jean-Claude; Souteyrand, Pierre; Chollet, Philippe

2005-10-01

Nitrosoureas possess some anti-tumor activity as a single agent in metastatic melanoma (MM). In a phase II trial, we evaluated the anti-tumor effects of cystemustine chemotherapy, a new nitrosourea, as a second-line treatment. Patients were required to have histologic evidence of disseminated MM and had failed in first-line chemotherapy. Treatment comprised cystemustine given at a dose of 60 mg/m every 2 weeks by a 15-min infusion. From February 1997 to September 1999, 22 patients (median age 66 years) were enrolled and were assessable. Two complete responses, one partial response, three stable diseases and 16 progressions were observed, giving an overall response rate of 13.6%. Median duration of response was 10 months (range 4-63). Median survival of responders and non-responders was 11 and 4 months, respectively. However, hematological toxicity, particularly thrombopenia, was a limiting factor for one-third of patients. We conclude that cystemustine at 60 mg/m is active in patients who progressed after one line of chemotherapy in advanced disease, and offers the possibility of complete responses and long durations of these responses.

Triangular M/G/1-type and tree-like QBD Markov chains

NARCIS (Netherlands)

Van Houdt, B.; Leeuwaarden, van J.S.H.

2009-01-01

In applying matrix-analytic methods to M/G/1-type and tree-like QBD Markov chains, it is crucial to determine the solution to a (set of) nonlinear matrix equation(s). This is usually done via iterative methods. We consider the highly structured subclass of triangular M/G/1-type and tree-like QBD

Thermodynamic investigation of the ternary mixed aqueous electrolyte (MgCl{sub 2} + MgSO{sub 4}) system by potentiometric method at T = 298.15 K

Energy Technology Data Exchange (ETDEWEB)

Bagherinia, Mohammad A., E-mail: mabagherinia@yahoo.com [Department of Chemistry, Faculty of Science, Lahijan Branch, Islamic Azad University, Lahijan (Iran, Islamic Republic of); Giahi, Masoud; Pournaghdy, Mohammad; Vaghar, Gholam R. [Department of Chemistry, Faculty of Science, Lahijan Branch, Islamic Azad University, Lahijan (Iran, Islamic Republic of)

2012-01-15

Highlights: > In this study we investigated the thermodynamic properties of MgCl{sub 2} + MgSO{sub 4} + H{sub 2}O. > The method used in this work was potentiometric method. > Mg-ISE and the Ag/AgCl electrodes used in this work had a good Nernst response. > The experimental results obeyed the Harned rule. > The Pitzer model could be used to describe this ternary system satisfactorily. - Abstract: This work reports the results of thermodynamic investigation of the ternary mixed-electrolyte system (MgCl{sub 2} + MgSO{sub 4} + H{sub 2}O). The investigation was performed based on Pitzer ion interaction model by using the potentiometric technique at T = 298.15 K. The mean activity coefficients of MgCl{sub 2} in the mixed aqueous electrolyte system were determined on the galvanic cell without liquid junction of the type: Mg-ISE|MgCl{sub 2} (m{sub A}), MgSO{sub 4} (m{sub B}), H{sub 2}O|Ag/AgCl over total ionic strengths from (0.001 to 8.000) mol . kg{sup -1} for different series of salt ratio r (r=m{sub MgCl{sub 2}}/m{sub MgSO{sub 4}}=2.5,5.0,7.5,10.0,15.0 and pure MgCl{sub 2}). The PVC based magnesium ion-selective electrode (Mg-ISE) and the Ag/AgCl electrode used in this work were made in our laboratory and had a reasonably good Nernst response. The experimental results obeyed the Harned rule, and the Pitzer model could be used to describe this ternary system satisfactorily. Pitzer ion-interaction parameters for mixed salts were determined for this system. Then, these parameters ({theta}{sub ClSO{sub 4}}=0.0252{+-}0.0042, {psi}{sub MgClSO{sub 4}}=-0.0049{+-}0.0003) were used to calculate the values of the mean activity coefficients of MgSO{sub 4}, the osmotic coefficients of water ({phi}) and the excess Gibbs free energies of solution (G{sup E}) for the whole series of the studied electrolyte systems.

Cubic Re6+ (5d1) Double Perovskites, Ba2MgReO6, Ba2ZnReO6, and Ba2Y2/3ReO6: Magnetism, Heat Capacity, μSR, and Neutron Scattering Studies and Comparison with Theory.

Science.gov (United States)

Marjerrison, Casey A; Thompson, Corey M; Sala, Gabrielle; Maharaj, Dalini D; Kermarrec, Edwin; Cai, Yipeng; Hallas, Alannah M; Wilson, Murray N; Munsie, Timothy J S; Granroth, Garrett E; Flacau, Roxana; Greedan, John E; Gaulin, Bruce D; Luke, Graeme M

2016-10-04

Double perovskites (DP) of the general formula Ba 2 MReO 6 , where M = Mg, Zn, and Y 2/3 , all based on Re 6+ (5d 1 , t 2g 1 ), were synthesized and studied using magnetization, heat capacity, muon spin relaxation, and neutron-scattering techniques. All are cubic, Fm3̅m, at ambient temperature to within the resolution of the X-ray and neutron diffraction data, although the muon data suggest the possibility of a local distortion for M = Mg. The M = Mg DP is a ferromagnet, T c = 18 K, with a saturation moment ∼0.3 bohr magnetons at 3 K. There are two anomalies in the heat capacity: a sharp feature at 18 K and a broad maximum centered near 33 K. The total entropy loss below 45 K is 9.68 e.u., which approaches R ln 4 (11.52 e.u.) supporting a j = 3/2 ground state. The unit cell constants of Ba 2 MgReO 6 and the isostructural, isoelectronic analogue, Ba 2 LiOsO 6 , differ by only 0.1%, yet the latter is an anti-ferromagnet. The M = Zn DP also appears to be a ferromagnet, T c = 11 K, μ sat (Re) = 0.1 μ B . In this case the heat capacity shows a somewhat broad peak near 10 K and a broader maximum at ∼33 K, behavior that can be traced to a smaller particle size, ∼30 nm, for this sample. For both M = Mg and Zn, the low-temperature magnetic heat capacity follows a T 3/2 behavior, consistent with a ferromagnetic spin wave. An attempt to attribute the broad 33 K heat capacity anomalies to a splitting of the j = 3/2 state by a crystal distortion is not supported by inelastic neutron scattering, which shows no transition at the expected energy of ∼7 meV nor any transition up to 100 meV. However, the results for the two ferromagnets are compared to the theory of Chen, Pereira, and Balents, and the computed heat capacity predicts the two maxima observed experimentally. The M = Y 2/3 DP, with a significantly larger cell constant (3%) than the ferromagnets, shows predominantly anti-ferromagnetic correlations, and the ground state is complex with a spin frozen component T

Concurrent chemoradiotherapy for advanced pancreatic cancer. 1,000 mg/m{sup 2} gemcitabine can be administered using limited-field radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Yamazaki, Hideya [Osaka Medical Center for Cancer and Cardiovascular Disease, Osaka (Japan). Dept. of Radiation Oncology; National Hospital Organization, Osaka National Hospital, Osaka (Japan). Dept. of Radiology; Nishiyama, Kinji; Koizumi, Masahiko; Tanaka, Eiichi [Osaka Medical Center for Cancer and Cardiovascular Disease, Osaka (Japan). Dept. of Radiation Oncology; Ioka, Tatsuya; Uehara, Hiroyuki; Iishi, Hiroyasu; Nakaizumi, Akihiko [Osaka Medical Center for Cancer and Cardiovascular Disease, Osaka (Japan). Dept. of Internal Medicine; Ohigashi, Hiroaki; Ishikawa, Osamu [Osaka Medical Center for Cancer and Cardiovascular Disease, Osaka (Japan). Dept. of Surgery

2007-06-15

Purpose: To examine the feasibility of concurrent use of full-dose gemcitabine (GEM) and radiotherapy for advanced pancreatic cancer. Patient and Methods: 22 patients with advanced pancreatic cancer were subjected to concurrent chemoradiotherapy (GEM 1,000 mg/m2 weekly, three times during 4 weeks). They received limited-field irradiation by three-dimensional radiotherapy planning. Results: Of the 22 patients, 16 (72%) completed the treatment (50 Gy irradiation and at least three times concurrent administration of 1 g/m{sup 2} GEM). One patient with unresectable tail cancer showed peritonitis carcinomatosa and both chemotherapy and radiotherapy had to be stopped. Dose reduction or omission of GEM was necessary in another four patients. In addition, radiotherapy was discontinued in one patient for fatigue. Grade 3 hematologic toxicity was detected in eight patients (36%), and grade 3 nonhematologic toxicity (anorexia) in one patient (5%). In total, the response rate amounted to 32% (seven partial responses), and the median survival time (MST) was 16 months. Among the twelve patients who received preoperative chemoradiotherapy, nine underwent surgery and showed a survival rate of 78% at 1 year. Another 13 patients without surgery showed 14 months of MST. No regional lymph node failure has appeared so far. Conclusion: Limited-field radiotherapy enables the safe concurrent administration of 1,000 mg/m{sup 2} GEM.

Comparison of 1 mg and 2 mg overnight dexamethasone suppression tests for the screening of Cushing's syndrome in obese patients.

Science.gov (United States)

Sahin, Mustafa; Kebapcilar, Levent; Taslipinar, Abdullah; Azal, Omer; Ozgurtas, Taner; Corakci, Ahmet; Akgul, Emin Ozgur; Taslipinar, Mine Yavuz; Yazici, Mahmut; Kutlu, Mustafa

2009-01-01

Obesity is currently a major public health problem and one of the potential underlying causes of obesity in a minority of patients is Cushing's syndrome (CS). Traditionally, the gold standard screening test for CS is 1 mg dexamethasone overnight suppression test. However, it is known that obese subjects have high false positive results with this test. We have therefore compared the 1 mg and 2 mg overnight dexamethasone suppression tests in obese subjects. Patients whose serum cortisol after ODST was >50 nM underwent and a low-dose dexamethasone suppression test (LDDST); 24-hour urine cortisol was collected for basal urinary free cortisol (UFC). For positive results after overnight 1-mg dexamethasone suppression test we also performed the overnight 2-mg dexamethasone suppression test. We prospectively evaluated 100 patients (22 men and 78 women, ranging in age from 17 to 73 years with a body mass index (BMI) >30 kg/m2 who had been referred to our hospital-affiliated endocrine clinic because of simple obesity. Suppression of serum cortisol to suppression. Thyroid function tests, lipid profiles, homocysteine, antithyroglobulin, anti-thyroid peroxidase antibody levels, vitamin B12, folate levels, insulin resistance [by homeostasis model assessment (HOMA)] and 1.0 mg postdexamethasone (postdex) suppression cortisol levels were measured. We found an 8% false-positive rate in 1 mg overnight test and 2% in 2 mg overnight test (p=0.001). There was no correlation between the cortisol levels after ODST and other parameters. Our results indicate that the 2 mg overnight dexamethasone suppression test (ODST) is more convenient and accurate than 1-mg ODST as a screening test for excluding CS in subjects with simple obesity.

Strong Dependence of Hydration State of F-Actin on the Bound Mg(2+)/Ca(2+) Ions.

Science.gov (United States)

Suzuki, Makoto; Imao, Asato; Mogami, George; Chishima, Ryotaro; Watanabe, Takahiro; Yamaguchi, Takaya; Morimoto, Nobuyuki; Wazawa, Tetsuichi

2016-07-21

Understanding of the hydration state is an important issue in the chemomechanical energetics of versatile biological functions of polymerized actin (F-actin). In this study, hydration-state differences of F-actin by the bound divalent cations are revealed through precision microwave dielectric relaxation (DR) spectroscopy. G- and F-actin in Ca- and Mg-containing buffer solutions exhibit dual hydration components comprising restrained water with DR frequency f2 (fw). The hydration state of F-actin is strongly dependent on the ionic composition. In every buffer tested, the HMW signal Dhyme (≡ (f1 - fw)δ1/(fwδw)) of F-actin is stronger than that of G-actin, where δw is DR-amplitude of bulk solvent and δ1 is that of HMW in a fixed-volume ellipsoid containing an F-actin and surrounding water in solution. Dhyme value of F-actin in Ca2.0-buffer (containing 2 mM Ca(2+)) is markedly higher than in Mg2.0-buffer (containing 2 mM Mg(2+)). Moreover, in the presence of 2 mM Mg(2+), the hydration state of F-actin is changed by adding a small fraction of Ca(2+) (∼0.1 mM) and becomes closer to that of the Ca-bound form in Ca2.0-buffer. This is consistent with the results of the partial specific volume and the Cotton effect around 290 nm in the CD spectra, indicating a change in the tertiary structure and less apparent change in the secondary structure of actin. The number of restrained water molecules per actin (N2) is estimated to be 1600-2100 for Ca2.0- and F-buffer and ∼2500 for Mg2.0-buffer at 10-15 °C. These numbers are comparable to those estimated from the available F-actin atomic structures as in the first water layer. The number of HMW molecules is roughly explained by the volume between the equipotential surface of -kT/2e and the first water layer of the actin surface by solving the Poisson-Boltzmann equation using UCSF Chimera.

Coherent interface structures and intergrain Josephson coupling in dense MgO/Mg{sub 2}Si/MgB{sub 2} nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Ueno, Katsuya; Takahashi, Kazuyuki; Uchino, Takashi, E-mail: uchino@kobe-u.ac.jp [Department of Chemistry, Graduate School of Science, Kobe University, Nada, Kobe 657-8501 (Japan); Nagashima, Yukihito [Nippon Sheet Glass Co., Ltd., Konoike, Itami 664-8520 (Japan); Seto, Yusuke [Department of Planetology, Graduate School of Science, Kobe University, Nada, Kobe 657-8501 (Japan); Matsumoto, Megumi; Sakurai, Takahiro [Center for Support to Research and Education Activities, Kobe University, Nada, Kobe 657-8501 (Japan); Ohta, Hitoshi [Molecular Photoscience Research Center, Kobe University, Nada, Kobe 657-8501 (Japan)

2016-07-07

Many efforts are under way to control the structure of heterointerfaces in nanostructured composite materials for designing functionality and engineering application. However, the fabrication of high-quality heterointerfaces is challenging because the crystal/crystal interface is usually the most defective part of the nanocomposite materials. In this work, we show that fully dense insulator (MgO)/semiconductor(Mg{sub 2}Si)/superconductor(MgB{sub 2}) nanocomposites with atomically smooth and continuous interfaces, including epitaxial-like MgO/Mg{sub 2}Si interfaces, are obtained by solid phase reaction between metallic magnesium and a borosilicate glass. The resulting nanocomposites exhibit a semiconductor-superconducting transition at 36 K owing to the MgB{sub 2} nanograins surrounded by the MgO/Mg{sub 2}Si matrix. This transition is followed by the intergrain phase-lock transition at ∼24 K due to the construction of Josephson-coupled network, eventually leading to a near-zero resistance state at 17 K. The method not only provides a simple process to fabricate dense nanocomposites with high-quality interfaces, but also enables to investigate the electric and magnetic properties of embedded superconducting nanograins with good intergrain coupling.

Nonparametric inference from the M/G/1 workload

DEFF Research Database (Denmark)

Hansen, Martin Bøgsted; Pitts, Susan M.

2006-01-01

Consider an M/G/1 queue with unknown service-time distribution and unknown traffic intensity ρ. Given systematically sampled observations of the workload, we construct estimators of ρ and of the service-time distribution function, and we study asymptotoic properties of these estimators....

Nonparametric inference from the M/G/1 workload

DEFF Research Database (Denmark)

Hansen, Martin Bøgsted; Pitts, Susan M.

Consider an M/G/1 queue with unknown service-time distribution and unknown traffic intensity $\\rho$. Given systematically sampled observations of the workload, we construct estimators of $\\rho$ and of the service-time distribution function, and we study asymptotic properties of these estimators....

Electronic Structure and Bonding Situation in M2O2 (M=Be,Mg,Ca) Rhombic Clusters.

Czech Academy of Sciences Publication Activity Database

Li, W.-L.; Lu, J.-B.; Zhao, L.; Ponec, Robert; Cooper, D.L.; Li, J.; Frenking, G.

Roč. 122, č. 10 ( 2018 ), s. 2816-2822 ISSN 1089-5639 Grant - others:NNSFCH(CN) 21590792; NNSFCH(CN) 21433005; NNSFCH(CN) 21703099; JPY NSF(CN) BK20170964; NTU(CN) 39837123 Institutional support: RVO:67985858 Keywords : electronic structures * M2O2n clustery * theoretical isnights Subject RIV: CF - Physical ; Theoretical Chemistry OBOR OECD: Physical chemistry Impact factor: 2.847, year: 2016

Nanocrystalline spinel ferrite (MFe{sub 2}O{sub 4}, M = Ni, Co, Mn, Mg, Zn) powders prepared by a simple aloe vera plant-extracted solution hydrothermal route

Energy Technology Data Exchange (ETDEWEB)

Phumying, Santi; Labuayai, Sarawuth; Swatsitang, Ekaphan; Amornkitbamrung, Vittaya [Department of Physics, Faculty of Science, Khon Kaen University, Khon Kaen 40002 (Thailand); Integrated Nanotechnology Research Center (INRC), Khon Kaen University, Khon Kaen 40002 (Thailand); Maensiri, Santi, E-mail: santimaensiri@gmail.com [School of Physics, Institute of Science, Suranaree University of Technology, Nakhon Ratchasima 30000 (Thailand)

2013-06-01

Graphical abstract: This figure shows the specific magnetization curves of the as-prepared MFe{sub 2}O{sub 4} (M = Ni, Co, Mn, Mg, Zn) powders obtained from room temperature VSM measurement. These curves are typical for a soft magnetic material and indicate hysteresis ferromagnetism in the field ranges of ±500 Oe, ±1000 Oe, and ±2000 Oe for the CoFe{sub 2}O{sub 4}, MgFe{sub 2}O{sub 4} and MnFe{sub 2}O{sub 4} respectively, whereas the samples of NiFe{sub 2}O{sub 4} and ZnFe{sub 2}O{sub 4} show a superparamagnetic behavior. Highlights: ► Nanocrystalline MFe{sub 2}O{sub 4} powders were synthesized by a novel hydrothermal method. ► Metal acetylacetonates and aloe vera plant-extracted solution are used. ► This biosynthetic route is very simple and provides high-yield oxide nanomaterials. ► XRD and TEM results indicate that the prepared samples have only spinel structure. ► The maximum M{sub s} of 68.9 emu/g at 10 kOe were observed for the samples of MnFe{sub 2}O{sub 4}. - Abstract: Nanocrystalline spinel ferrite MFe{sub 2}O{sub 4} (M = Ni, Co, Mn, Mg, Zn) powders were synthesized by a novel hydrothermal method using Fe(acac){sub 3}, M(acac){sub 3} (M = Ni, Co, Mn, Mg, Zn) and aloe vera plant extracted solution. The X-ray diffraction and selected-area electron diffraction results indicate that the synthesized nanocrystalline have only spinel structure without the presence of other phase impurities. The crystal structure and morphology of the spinel ferrite powders, as revealed by TEM, show that the NiFe{sub 2}O{sub 4} and CoFe{sub 2}O{sub 4} samples contain nanoparticles, whereas the MnFe{sub 2}O{sub 4} and MgFe{sub 2}O{sub 4} samples consist of many nanoplatelets and nanoparticles. Interestingly, the ZnFe{sub 2}O{sub 4} sample contains plate-like structure of networked nanocrystalline particles. Room temperature magnetization results show a ferromagnetic behavior of the CoFe{sub 2}O{sub 4}, MnFe{sub 2}O{sub 4} and MgFe{sub 2}O{sub 4} samples, whereas the

Depth-dependent and surface damages in MgAl sub 2 O sub 4 and MgO irradiated with energetic iodine ions

CERN Document Server

Aruga, T; Ohmichi, T; Okayasu, S; Kazumata, Y; Jitsukawa, S

2002-01-01

Samples of polycrystalline ceramics of MgAl sub 2 O sub 4 irradiated at the ambient temperature with 85 MeV I sup 7 sup + iodine ions to doses up to 1x10 sup 1 sup 9 m sup - sup 2 is observed to be amorphized up to depths around 6 mu m from the ion-incident surface for a dose of 1.2x10 sup 1 sup 9 m sup - sup 2 , through a cross-sectional transmission electron microscopy. A step height of 1 mu m is formed across the border between the masked and irradiated regions of the surface. The height of the step is observed to increase sharply from the irradiated area towards the edge at the border, forming a peak as tall as 1.5 mu m. A glossy, silver-gray film with a thickness less than 0.1 mu m is unexpectedly observed to have formed on the surface of samples of MgAl sub 2 O sub 4 and MgO, in about 3.5 years aging after the irradiation to 1.2x10 sup 1 sup 9 m sup - sup 2 , being left untouched in the air. The film is easily peeled off along grain boundaries and found to be amorphous from the electron diffraction patt...

A solid solution series of atacamite type Ni{sub 2x}Mg{sub 2−2x}Cl(OH){sub 3}

Energy Technology Data Exchange (ETDEWEB)

Bette, Sebastian [TU Bergakademie Freiberg, Institute of Inorganic Chemistry, Leipziger Strasse 29, Freiberg 09596 (Germany); Dinnebier, Robert E. [Max Planck Institute for Solid State Research, Heisenbergstrasse 1, Stuttgart 70569 (Germany); Röder, Christian [TU Bergakademie Freiberg, Institute of Theoretical Physics, Leipziger Strasse 23, Freiberg 09596 (Germany); Freyer, Daniela, E-mail: daniela.freyer@chemie.tu-freiberg.de [TU Bergakademie Freiberg, Institute of Inorganic Chemistry, Leipziger Strasse 29, Freiberg 09596 (Germany)

2015-08-15

For the first time a complete solid solution series Ni{sub 2x}Mg{sub 2−2x}Cl(OH){sub 3} of an atacamite type alkaline main group metal chloride, Mg{sub 2}Cl(OH){sub 3}, and a transition group metal chloride, Ni{sub 2}Cl(OH){sub 3}, was prepared and characterized by chemical and thermal analysis as well as by Raman and IR spectroscopy, and high resolution laboratory X-ray powder diffraction. All members of the solid solution series crystallize in space group Pnam (62). The main building units of these crystal structures are distorted, edge-linked Ni/MgO{sub 4}Cl{sub 2} and Ni/MgO{sub 5}Cl octahedra. The distribution of Ni{sup 2+}- and Mg{sup 2+}-ions among these two metal-sites within the solid solution series is discussed in detail. The crystallization of the solid solution phases occurs via an intermediate solid solution series, (Ni/Mg)Cl{sub 2x}(OH){sub 2−2x}, with variable Cl: OH ratio up to the 1:3 ratio according to the formula Ni{sub 2x}Mg{sub 2−2x} Cl(OH){sub 3}. For one isolated intermediate solid solution member, Ni{sub 0.70}Mg{sub 0.30}Cl{sub 0.58}(OH){sub 1.42}, the formation and crystal structure is presented as well. - Graphical abstract: For the first time a complete solid solution series, Ni{sub 2x}Mg{sub 2−2x} Cl(OH){sub 3}, was synthesized and characterized. Structure solution by revealed that Ni{sup 2+} prefers to occupy the Jahn–Teller-like distorted hole, out of two available cation sites. Substitution of Ni{sup 2+} by Mg{sup 2+} in atacamite type Ni{sub 2}Cl(OH){sub 3} results in systematic band shifts in Raman and IR spectra as well as in systematic changes in thermal properties. The α-polymorphs M{sub 2}Cl(OH){sub 3} with M=Mg{sup 2+}, Ni{sup 2+} and other divalent transition metal ions, as described in literature, were identified as separate compounds. - Highlights: • First synthesis of solid solution series between main and transition metal chloride. • Ni{sup 2+} prefers to occupy Jahn–Teller-like distorted octahedral holes

Splitting of ISGMR strength in the light-mass nucleus 24Mg due to ground-state deformation

Directory of Open Access Journals (Sweden)

Y.K. Gupta

2015-09-01

Full Text Available The isoscalar giant monopole resonance (ISGMR strength distribution in 24Mg has been determined from background-free inelastic scattering of 386-MeV α particles at extreme forward angles, including 0∘. The ISGMR strength distribution has been observed for the first time to have a two-peak structure in a light-mass nucleus. This splitting of ISGMR strength is explained well by microscopic theory in terms of the prolate deformation of the ground state of 24Mg.

Persistence of metastable vortex lattice domains in MgB2 in the presence of vortex motion.

Science.gov (United States)

Rastovski, C; Schlesinger, K J; Gannon, W J; Dewhurst, C D; DeBeer-Schmitt, L; Zhigadlo, N D; Karpinski, J; Eskildsen, M R

2013-09-06

Recently, extensive vortex lattice metastability was reported in MgB2 in connection with a second-order rotational phase transition. However, the mechanism responsible for these well-ordered metastable vortex lattice phases is not well understood. Using small-angle neutron scattering, we studied the vortex lattice in MgB2 as it was driven from a metastable to the ground state through a series of small changes in the applied magnetic field. Our results show that metastable vortex lattice domains persist in the presence of substantial vortex motion and directly demonstrate that the metastability is not due to vortex pinning. Instead, we propose that it is due to the jamming of counterrotated vortex lattice domains which prevents a rotation to the ground state orientation.

An essential factor for high Mg2+ tolerance of Staphylococcus aureus

Directory of Open Access Journals (Sweden)

Joshua Armitano

2016-11-01

Full Text Available Internal bacterial concentration of Mg2+, the most abundant divalent cation in living cells, is estimated to be in the single millimolar range. However, many bacteria will thrive in media with only micromolars of Mg2+, by using a range of intensely studied and highly efficient import mechanisms, as well as in media with very high magnesium concentration, presumably mediated by currently unknown export mechanisms. Staphylococcus aureus has a particularly high Mg2+ tolerance for a pathogen, growing unimpaired in up to 770 mM Mg2+, and we here identify SA0657, a key factor in this tolerance. The predicted domain structure of SA0657 is shared with a large number of proteins in bacteria, archaea and even eukarya, for example CorB from Salmonella and the human CNNM protein family. One of the shared domains, a CBS pair potentially involved in Mg2+ sensing, contains the conserved Glycine326 which we establish to be a key residue for SA0657 function. In light of our findings, we propose the name MpfA, Magnesium Protection Factor A, for SA0657.

Ca(2+-dependent regulation of the Ca(2+ concentration in the myometrium mitochondria. II. Ca(2+ effects on mitochondria membranes polarization and [Ca(2+](m

Directory of Open Access Journals (Sweden)

L. G. Babich

2017-06-01

Full Text Available It is known that Ca2+ accumulation in the mitochondria undergoes complex regulation by Ca2+ itself. But the mechanisms of such regulation are still discussed. In this paper we have shown that Ca ions directly or indirectly regulate the level of myometrium mitochondria membranes polarization. The additions of 100 µM Ca2+ were accompanied by depolarization of the mitochondria membranes. The following experiments were designed to study the impact of Ca2+ on the myometrium mitochondria [Ca2+]m. Isolated myometrium mitochondria were preincubated without or with 10 μM Са2+ followed by 100 μM Са2+ addition. Experiments were conducted in three mediums: without ATP and Mg2+ (0-medium, in the presence of 3 mM Mg2+ (Mg-medium and 3 mM Mg2+ + 3 mM ATP (Mg,ATP-medium. It was shown that the effects of 10 μM Са2+ addition were different in different mediums, namely in 0- and Mg-medium the [Ca2+]m values increased, whereas in Mg,ATP-medium statistically reliable changes were not registered. Preincubation of mitochondria with 10 μM Са2+ did not affect the [Ca2+]m value after the addition of 100 μM Са2+. The [Ca2+]m values after 100 μM Са2+ addition were the same in 0- and Mg,ATP-mediums and somewhat lower in Mg-medium. Preliminary incubation of mitochondria with 10 μM Са2+ in 0- and Mg-mediums reduced changes of Fluo 4 normalized fluorescence values that were induced by 100 μM Са2+ additions, but in Mg,ATP-medium such differences were not recorded. It is concluded that Са2+ exchange in myometrium mitochondria is regulated by the concentration of Ca ions as in the external medium, so in the matrix of mitochondria. The medium composition had a significant impact on the [Са2+]m values in the absence of exogenous cation. It is suggested that light increase of [Са2+]m before the addition of 100 μM Са2+ may have a positive effect on the functional activity of the mitochondria.

The 2011 Mineral, VA M5.8 Earthquake Ground Motions and Stress Drop: An Important Contribution to the NGA East Ground Motion Database

Science.gov (United States)

Cramer, C. H.; Kutliroff, J.; Dangkua, D.

2011-12-01

The M5.8 Mineral, Virginia earthquake of August 23, 2011 is the largest instrumentally recorded earthquake in eastern North America since the 1988 M5.9 Saguenay, Canada earthquake. Historically, a similar magnitude earthquake occurred on May 31, 1897 at 18:58 UCT in western Virginia west of Roanoke. Paleoseismic evidence for larger magnitude earthquakes has also been found in the central Virginia region. The Next Generation Attenuation (NGA) East project to develop new ground motion prediction equations for stable continental regions (SCRs), including eastern North America (ENA), is ongoing at the Pacific Earthquake Engineering Research Center funded by the U.S. Nuclear Regulatory Commission, the U.S. Geological Survey, the Electric Power Research Institute, and the U.S. Department of Energy. The available recordings from the M5.8 Virginia are being added to the NGA East ground motion database. Close in (less than 100 km) strong motion recordings are particularly interesting for both ground motion and stress drop estimates as most close-in broadband seismometers clipped on the mainshock. A preliminary estimate for earthquake corner frequency for the M5.8 Virginia earthquake of ~0.7 Hz has been obtained from a strong motion record 57 km from the mainshock epicenter. For a M5.8 earthquake this suggests a Brune stress drop of ~300 bars for the Virginia event. Very preliminary comparisons using accelerometer data suggest the ground motions from the M5.8 Virginia earthquake agree well with current ENA ground motion prediction equations (GMPEs) at short periods (PGA, 0.2 s) and are below the GMPEs at longer periods (1.0 s), which is the same relationship seen from other recent M5 ENA earthquakes. We will present observed versus GMPE ground motion comparisons for all the ground motion observations and stress drop estimates from strong motion recordings at distances less than 100 km. A review of the completed NGA East ENA ground motion database will also be provided.

Geometric Magnetic Frustration in Li3Mg2OsO6 Studied with Muon Spin Relaxation

Science.gov (United States)

Carlo, J. P.; Derakhshan, S.; Greedan, J. E.

Geometric frustration manifests when the spatial arrangement of ions inhibits magnetic order. Typically associated with antiferromagnetically (AF)-correlated moments on triangular or tetrahedral lattices, frustration occurs in a variety of structures and systems, resulting in rich phase diagrams and exotic ground states. As a window to exotic physics revealed by the cancellation of normally dominant interactions, the research community has taken great interest in frustrated systems. One family of recent interest are the rock-salt ordered oxides A5BO6, in which the B sites are occupied by magnetic ions comprising a network of interlocked tetrahedra, and nonmagnetic ions on the A sites control the B oxidation state through charge neutrality. Here we will discuss studies of Li3Mg2OsO6 using muon spin relaxation (μSR), a highly sensitive local probe of magnetism. Previous studies of this family included Li5OsO6, which exhibits AF order below 50K with minimal evidence for frustration, and Li4MgReO6, which exhibits glassy magnetism. Li3Mg2RuO6, meanwhile, exhibits long-range AF, with the ordering temperature suppressed by frustration. But its isoelectronic twin, Li3Mg2OsO6 (5d3 vs. 4d3) exhibits very different behavior, revealed by μSR to be a glassy ground state below 12K. Understanding why such similar systems exhibit diverse ground-state behavior is key to understanding the nature of geometric magnetic frustration. Financial support from the Research Corporation for Science Advancement.

Air-stable hydrogen generation materials and enhanced hydrolysis performance of MgH2-LiNH2 composites

Science.gov (United States)

Ma, Miaolian; Ouyang, Liuzhang; Liu, Jiangwen; Wang, Hui; Shao, Huaiyu; Zhu, Min

2017-08-01

Hydrolysis of materials in water can be a promising solution of onsite hydrogen generation for realization of hydrogen economy. In this work, it was the first time that the MgH2-LiNH2 composites were explored as air-stable hydrolysis system for hydrogen generation. The MgH2-LiNH2 composites with different composition ratios were synthesized by ball milling with various durations and the hydrogen generation performances of the composite samples were investigated and compared. X-ray diffraction, X-ray photoelectron spectroscopy and scanning electron microscopy techniques were adopted to elucidate the performance improvement mechanisms. The hydrolysis properties of MgH2 were found to be significantly enhanced by the introduction of LiNH2. The 4MgH2-LiNH2 composite ball milled for 5 h can generate 887.2 mL g-1 hydrogen in 1 min and 1016 mL g-1 in 50 min, one of the best results so far for Mg based hydrolysis materials. The LiOH·H2O and NH4OH phases of hydrolysis products from LiNH2 may prevent formation of Mg(OH)2 passivation layer on the surface and supply enough channels for hydrolysis of MgH2. The MgH2-LiNH2 composites appeared to be very stable in air and no obvious negative effect on kinetics and hydrogen generation yield was observed. These good performances demonstrate that the studied MgH2-LiNH2 composites can be a promising and practicable hydrogen generation system.

Molecular cloning, purification, and characterization of a novel polyMG-specific alginate lyase responsible for alginate MG block degradation in Stenotrophomas maltophilia KJ-2

Energy Technology Data Exchange (ETDEWEB)

Lee, Su In; Kim, Hee Sook [Kyungsung Univ., Busan (Korea, Republic of). Dept. of Food Science and Biotechnology; Choi, Sung Hee; Lee, Eun Yeol [Kyung Hee Univ., Gyeonggi-do (Korea, Republic of). Dept. of Chemical Engineering

2012-09-15

A gene for a polyMG-specific alginate lyase possessing a novel structure was identified and cloned from Stenotrophomas maltophilia KJ-2 by using PCR with homologous nucleotide sequences-based primers. The recombinant alginate lyase consisting of 475 amino acids was purified on Ni-Sepharose column and exhibited the highest activity at pH 8 and 40 C. Interestingly, the recombinant alginate lyase was expected to have a similar catalytic active site of chondroitin B lyase but did not show chondroitin lyase activity. In the test of substrate specificity, the recombinant alginate lyase preferentially degraded the glycosidic bond of polyMG-block than polyM-block and polyG-block. The chemical structures of the degraded alginate oligosaccharides were elucidated to have mannuronate (M) at the reducing end on the basis of NMR analysis, supporting that KJ-2 polyMG-specific alginate lyase preferably degraded the glycosidic bond in M-G linkage than that in G-M linkage. The KJ-2 polyMG-specific alginate lyase can be used in combination with other alginate lyases for a synergistic saccharification of alginate. (orig.)

Development of pure Mg open-cell foams as structured CO{sub 2} captor

Energy Technology Data Exchange (ETDEWEB)

Figueroa, I.A., E-mail: iafiguera@unam.mx [Instituto de Investigaciones en Materiales, Universidad Nacional Autónoma de México (UNAM), Circuito Exterior S/N, Cd. Universitaria, C.P. 04510 México, D.F. (Mexico); Suarez, M.A.; Velasco-Castro, M.; Pfeiffer, H.; Alcántar-Vázquez, B.; González, G. [Instituto de Investigaciones en Materiales, Universidad Nacional Autónoma de México (UNAM), Circuito Exterior S/N, Cd. Universitaria, C.P. 04510 México, D.F. (Mexico); Alfonso, I. [Instituto de Investigaciones en Materiales, Unidad Morelia, Universidad Nacional Autónoma de México, Campus Morelia UNAM, Antigua Carretera a Pátzcuaro No. 8701, Col. Ex-Hacienda de San José de la Huerta, C.P. 58190 Morelia, Michoacán (Mexico); Lara-Rodríguez, G.A. [Instituto de Investigaciones en Materiales, Universidad Nacional Autónoma de México (UNAM), Circuito Exterior S/N, Cd. Universitaria, C.P. 04510 México, D.F. (Mexico)

2015-12-10

Highlights: • The CO{sub 2} capture capacity of the open-cell Mg foams was studied at low temperatures. • Open-cell Mg foams with pore size of 350 μm were used for the CO{sub 2} capture study. • The highest amount of CO{sub 2} captured was obtained at 60 °C and 80% of relative humidity. • A CO{sub 2} capture capacity of 0.87 mmol/g was obtained for the open-cell Mg foams. • The oxidized open-cell Mg foams can be used as CO{sub 2} captors. - Abstract: The CO{sub 2} capture capacity of the superficial oxide layer formed in pure open-cell Mg foams was studied at low temperatures (40–60 °C) varying the relative humidity from 40 to 80%. Mg foam samples with pore size of 350 μm and surface area of 5.4 m{sup 2}/g were used for these analyses. Optical microscopy and X-ray diffraction techniques were used to characterize the cell structure and the superficial oxide formed in the cell-foams, respectively. The final products formed after the CO{sub 2}–H{sub 2}O capture experiments were identified by scanning electron microscopy and attenuated total reflexion-Fourier transform infrared spectroscopy (ATR-FTIR). The MgCO{sub 3} and other products, formed after CO{sub 2} + H{sub 2}O capture process, were thermally decomposed, to quantify the amount of CO{sub 2} captured by the superficial MgO layer using standard thermogravimetric analysis. The results showed that the highest amount of CO{sub 2} captured was obtained at 60 °C and 80% of relative humidity, with a CO{sub 2} capture capacity of 0.87 mmol/g, which is comparable with others CO{sub 2} MgO-based captors. The considerable CO{sub 2} capture capacity at low temperatures supports the potential of the pure open-cell Mg foams to be used as structured CO{sub 2} captors.

Structural studies of disordered Mg2NiH4 formed by mechanical grinding

DEFF Research Database (Denmark)

Rönnebro, Ewa; Jensen, Jens Oluf; Noréus, Dag

1999-01-01

The low temperature phase of Mg2NiH4 was mechanically ground in argon atmosphere. The ordered monoclinic structure was destroyed to form the disordered cubic structure, previously only found above 510 K. With a Guinier-Hagg X-ray camera the cell parameter was determined to be a=6.492(3) Angstrom....

The M/G/1 queue with permanent customers

NARCIS (Netherlands)

Boxma, O.J.; Cohen, J.W.

1991-01-01

The authors examine an M/G/1 FCFS (first come, first served) queue with two types of customers: ordinary customers, who arrive according to a Poisson process, and permanent customers, who immediately return to the end of the queue after having received a service. The influence of the permanent

Modeling and stabilities of Mg/MgH2 interfaces: A first-principles investigation

Directory of Open Access Journals (Sweden)

Jia-Jun Tang

2014-07-01

Full Text Available We have theoretically investigated the modeling and the structural stabilities of various Mg/MgH2 interfaces, i.e. Mg(101¯0/MgH2(210, Mg(0001/MgH2(101 and Mg(101¯0/MgH2(101, and provided illuminating insights into Mg/MgH2 interface. Specifically, the main factors, which impact the interfacial energies, are fully considered, including surface energies of two phases, mutual lattice constants of interface model, and relative position of two phases. The surface energies of Mg and MgH2, on the one hand, are found to be greatly impacting the interfacial energies, reflected by the lowest interfacial energy of Mg(0001/MgH2(101 which is comprised of two lowest energy surfaces. On the other hand, it is demonstrated that the mutual lattice constants and the relative position of two phases lead to variations of interfacial energies, thus influencing the interface stabilities dramatically. Moreover, the Mg-H bonding at interface is found to be the determinant of Mg/MgH2 interface stability. Lastly, interfacial and strain effects on defect formations are also studied, both of which are highly facilitating the defect formations. Our results provide a detailed insight into Mg/MgH2 interface structures and the corresponding stabilities.

Quantitative electron microscopy and spectroscopy of MgB2 wires and tapes

International Nuclear Information System (INIS)

Birajdar, B; Peranio, N; Eibl, O

2008-01-01

In MgB 2 the correlation of microstructure with superconducting properties, in particular the critical current density, requires powerful analytical tools. Critical current densities and electrical resistivities of different MgB 2 superconductors differ by orders of magnitudes and the current limiting mechanisms have not been fully understood. Granularity of MgB 2 is one significant reason for reduced critical current densities and is introduced intrinsically by the anisotropy of B c2 but also extrinsically by the microstructure of the material. B c2 enhancement by doping is another important challenge for chemical analysis and, at present, doping levels are not well controlled on the sub-μm scale. In this paper the quantitative electron microscopy and spectroscopy methods essential for the microstructural analysis of MgB 2 are described. By quantitative electron microscopy and spectroscopy we mean a combined SEM and TEM analysis that covers various length scales from μm to nm. Contamination-free sample preparation, chemical mapping including B, and advanced chemical quantification using x-ray microanalysis were essential elements of the applied methodology. The methodology was applied to in situ and ex situ MgB 2 wires and tapes with and without SiC additives. Quantitative B analysis by EDX spectroscopy was applied quantitatively in the SEM and TEM, which is a major achievement. Although MgB 2 is a binary system, the thermodynamics of phase formation is complex, and the complexity is dramatically increased if additives like SiC are used. The small, sub-μm grain sizes of the matrix and secondary phases require TEM methods. However, granularity on the μm scale was also identified and underlines the importance of the combined SEM and TEM studies. Significant differences in the microstructure were observed for in situ and ex situ samples. This holds particularly if SiC was added and yielded Mg 2 Si for in situ samples annealed at 600-650 deg. C and Mg-Si-O phases

Reduction of hydrogen desorption temperature of ball-milled MgH2 by NbF5 addition

International Nuclear Information System (INIS)

Recham, N.; Bhat, V.V.; Kandavel, M.; Aymard, L.; Tarascon, J.-M.; Rougier, A.

2008-01-01

Enhanced sorption properties of ball-milled MgH 2 are reported by adding NbF 5 . Among various catalyst amounts, 2 mol% of NbF 5 reveals to be the optimum concentration leading to significant reduction of the desorption temperature as well as faster kinetics of ball-milled MgH 2 . At 200 deg. C, temperature at which MgH 2 does not show any activity, MgH 2NbF 5 /2mol% composite desorbs 3.2 wt.% of H 2 in 50 mins. Interestingly, the addition of NbF 5 is also associated with an increase in the desorption pressure. At 300 deg. C, MgH 2NbF 5 /2mol% composite starts to desorb hydrogen at 600 mbar in comparison with 1 mbar for MgH 2 . Further improvements were successfully achieved by pre-grinding NbF 5 prior to ball-milling the catalyst with MgH 2 . Such pre-ground NbF 5 catalyzed MgH 2 composite desorbs 3 wt.% of H 2 at 150 deg. C. Improved properties are associated with smaller activation energies down to values close to the enthalpy of formation of MgH 2 . Finally, the mechanism at the origin of the enhancement is discussed in terms of catalyst stability, MgF 2 formation and electronic density localization

Ropivacaine 7.5 mg/mL for Caesarean Section

Directory of Open Access Journals (Sweden)

N. K. Nguyen

2010-01-01

Full Text Available Background. Pain after Caesarean delivery is partly related to Pfannenstiel incision, which can be infiltrated with local anaesthetic solutions. Methods. A double- blind randomized control trial was designed to assess the analgesic efficacy of 7.5 mg/mL ropivacaine solution compared to control group, in two groups of one hundred and forty four parturients for each group, who underwent Caesarean section under spinal anaesthesia: group R (ropivacaine group and group C (control group. All parturients also received spinal sufentanil (2.5 g. Results. Ropivacaine infiltration in the Pfannenstiel incision for Caesarean delivery before wound closure leads to a reduction of 30% in the overall consumption of analgesics (348 550 mg for group R versus 504 426 mg for group C with <.05, especially opioids in the first 24 hours, but also significantly increases the time interval until the first request for an analgesic (4 h 20 min ± 2 h 26 for group R versus 2 h 42 ± 1 h 30 for group C. The P values for the two groups were: <.0001 for paracetamol, <.0001 for ketoprofen and P for nalbuphine which was the most significant. There is no significant difference in the threshold of VAS in the two series. Conclusion. This technique can contribute towards a programme of early rehabilitation in sectioned mothers, with earlier discharge from the post-labour suite.

Structural and magnetic properties of two branches of the tripod-kagome-lattice family A2R3Sb3O14 (A = Mg, Zn; R = Pr, Nd, Gd, Tb, Dy, Ho, Er, Yb)

Science.gov (United States)

Dun, Z. L.; Trinh, J.; Lee, M.; Choi, E. S.; Li, K.; Hu, Y. F.; Wang, Y. X.; Blanc, N.; Ramirez, A. P.; Zhou, H. D.

2017-03-01

We present a systematic study of the structural and magnetic properties of two branches of the rare-earth tripod-kagome-lattice (TKL) family A2R3Sb3O14 (A = Mg, Zn; R = Pr, Nd, Gd, Tb, Dy, Ho, Er, Yb; here, we use abbreviation A-R, as in MgPr for Mg2Pr3Sb3O14 ), which complements our previously reported work on MgDy, MgGd, and MgEr [Z. L. Dun et al., Phys. Rev. Lett. 116, 157201 (2016), 10.1103/PhysRevLett.116.157201]. The present susceptibility (χdc, χac) and specific-heat measurements reveal various magnetic ground states, including the nonmagnetic singlet state for MgPr, ZnPr; long-range orderings (LROs) for MgGd, ZnGd, MgNd, ZnNd, and MgYb; a long-range magnetic charge ordered state for MgDy, ZnDy, and potentially for MgHo; possible spin-glass states for ZnEr, ZnHo; the absence of spin ordering down to 80 mK for MgEr, MgTb, ZnTb, and ZnYb compounds. The ground states observed here bear both similarities as well as striking differences from the states found in the parent pyrochlore systems. In particular, while the TKLs display a greater tendency towards LRO, the lack of LRO in MgHo, MgTb, and ZnTb can be viewed from the standpoint of a balance among spin-spin interactions, anisotropies, and non-Kramers nature of single-ion state. While substituting Zn for Mg changes the chemical pressure, and subtly modifies the interaction energies for compounds with larger R ions, this substitution introduces structural disorder and modifies the ground states for compounds with smaller R ions (Ho, Er, Yb).

The TRPM6 Kinase Domain Determines the Mg·ATP Sensitivity of TRPM7/M6 Heteromeric Ion Channels*

Science.gov (United States)

Zhang, Zheng; Yu, Haijie; Huang, Junhao; Faouzi, Malika; Schmitz, Carsten; Penner, Reinhold; Fleig, Andrea

2014-01-01

The transient receptor potential melastatin member 7 (TRPM7) and member 6 (TRPM6) are divalent cation channel kinases essential for magnesium (Mg2+) homeostasis in vertebrates. It remains unclear how TRPM6 affects divalent cation transport and whether this involves functional homomeric TRPM6 plasma membrane channels or heteromeric channel assemblies with TRPM7. We show that homomeric TRPM6 is highly sensitive to intracellular free Mg2+ and therefore unlikely to be active at physiological levels of [Mg2+]i. Co-expression of TRPM7 and TRPM6 produces heteromeric TRPM7/M6 channels with altered pharmacology and sensitivity to intracellular Mg·ATP compared with homomeric TRPM7. Strikingly, the activity of heteromeric TRPM7/M6 channels is independent of intracellular Mg·ATP concentrations, essentially uncoupling channel activity from cellular energy status. Disruption of TRPM6 kinase phosphorylation activity re-introduces Mg·ATP sensitivity to the heteromeric channel similar to that of TRPM7. Thus, TRPM6 modulates the functionality of TRPM7, and the TRPM6 kinase plays a critical role in tuning the phenotype of the TRPM7·M6 channel complex. PMID:24385424

The TRPM6 kinase domain determines the Mg·ATP sensitivity of TRPM7/M6 heteromeric ion channels.

Science.gov (United States)

Zhang, Zheng; Yu, Haijie; Huang, Junhao; Faouzi, Malika; Schmitz, Carsten; Penner, Reinhold; Fleig, Andrea

2014-02-21

The transient receptor potential melastatin member 7 (TRPM7) and member 6 (TRPM6) are divalent cation channel kinases essential for magnesium (Mg(2+)) homeostasis in vertebrates. It remains unclear how TRPM6 affects divalent cation transport and whether this involves functional homomeric TRPM6 plasma membrane channels or heteromeric channel assemblies with TRPM7. We show that homomeric TRPM6 is highly sensitive to intracellular free Mg(2+) and therefore unlikely to be active at physiological levels of [Mg(2+)]i. Co-expression of TRPM7 and TRPM6 produces heteromeric TRPM7/M6 channels with altered pharmacology and sensitivity to intracellular Mg·ATP compared with homomeric TRPM7. Strikingly, the activity of heteromeric TRPM7/M6 channels is independent of intracellular Mg·ATP concentrations, essentially uncoupling channel activity from cellular energy status. Disruption of TRPM6 kinase phosphorylation activity re-introduces Mg·ATP sensitivity to the heteromeric channel similar to that of TRPM7. Thus, TRPM6 modulates the functionality of TRPM7, and the TRPM6 kinase plays a critical role in tuning the phenotype of the TRPM7·M6 channel complex.

Study of the reversible water vapour sorption process of MgSO{sub 4}.7H{sub 2}O and MgCl{sub 2}.6H{sub 2}O under the conditions of seasonal solar heat storage

Energy Technology Data Exchange (ETDEWEB)

Ferchaud, C.J.; De Boer, R. [Eindhoven University of Technology, Department of Mechanical Engineering, Eindhoven (Netherlands); Zondag, H.A.; Veldhuis, J.B.J. [ECN Biomass and Energy Efficiency, Petten (Netherlands)

2012-08-15

The characterization of the structural, compositional and thermodynamic properties of MgSO{sub 4}.7H{sub 2}O and MgCl{sub 2}.6H{sub O} has been done for seasonal heat storage using in-situ X-ray Diffraction and thermal analyses (TG/DSC) under practical conditions for seasonal heat storage (T{sub max} = 150C, p(H{sub 2}O)=13 mbar). This study showed that these two materials release heat after a dehydration/hydration cycle with energy densities of 0.38 GJ/m{sup 3} for MgSO{sub 4}.7H{sub 2}O and 0.71 GJ/m{sup 3} MgCl{sub 2}.6H{sub 2}O. The low heat release found for MgSO{sub 4}.7H2O is mainly attributed to the amorphization of the material during the dehydration performed at 13 mbar which reduces its sorption capacity during the rehydration. MgCl{sub 2}.6H{sub 2}O presents a high energy density which makes this material interesting for the seasonal heat storage in domestic applications. This material would be able to fulfil the winter heat demand of a passive house estimated at 6 GJ with a packed bed reactor of 8.5 m{sup 3}. However, a seasonal heat storage system based on the water vapour sorption process in MgCl{sub 2}.6H{sub 2}O should be carefully set with a restricted temperature of 40C for the hydration reaction to avoid the liquefaction of the material at ambient temperature which limits its performances for long term storage.

Preliminary study of the characteristics of a high Mg containing Al-Mg-Si alloy

International Nuclear Information System (INIS)

Yan, F; McKay, B J; Fan, Z; Chen, M F

2012-01-01

An Al-20Mg-4Si high Mg containing alloy has been produced and its characteristics investigated. The as-cast alloy revealed primary Mg 2 Si particles evenly distributed throughout an α-Al matrix with a β-Al 3 Mg 2 fully divorced eutectic phase observed in interdendritic regions. The Mg 2 Si particles displayed octahedral, truncated octahedral, and hopper morphologies. Additions of Sb, Ti and Zr had a refining influence reducing the size of the Mg 2 Si from 52 ± 4 μm to 25 ± 0.1 μm, 35 ± 1 μm and 34 ± 1 μm respectively. HPDC tensile test samples could be produced with a 0.6 wt.% Mn addition which prevented die soldering. Solution heating for 1 hr was found to dissolve the majority of the Al 3 Mg 2 eutectic phase with no evidence of any effect on the primary Mg 2 Si. Preliminary results indicate that the heat treatment has a beneficial effect on the elongation and the UTS.

Superconductivity of powder-in-tube MgB{sub 2} wires

Energy Technology Data Exchange (ETDEWEB)

Glowacki, B A; Evetts, J E [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); Department of Materials Science and Metallurgy, Pembroke Street, Cambridge, CB2 3QZ (United Kingdom); Majoros, M [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); Institute of Electrical Engineering, Slovak Academy of Science, Dubravska Cesta 9, Bratislava (Slovakia); Vickers, M [Department of Materials Science and Metallurgy, Pembroke Street, Cambridge, CB2 3QZ (United Kingdom); Shi, Y [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); McDougall, I [Oxford Instruments Plc, Eynsham, OX8 ITL (United Kingdom)

2001-04-01

A new class of 'powder-in-tube' Mg-B superconducting conductors has been prepared using two different methods: an in situ technique where an Mg + 2B mixture was used as a central conductor core and reacted in situ to form MgB{sub 2}, and an ex situ technique where fully reacted MgB{sub 2} powder was used to fill the metal tube. Conductors were prepared using silver, copper and bimetallic silver/stainless steel tubes. Wires manufactured by the in situ technique, diffusing Mg to B particles experienced {approx}25.5% decrease in density from the initial value after cold deformation, due to the phase transformation from Mg + 2({beta}-B){yields}MgB{sub 2} all with hexagonal structure. A comparative study of the intergranular current and grain connectivity in wires was conducted by AC susceptibility measurements and direct four point transport measurements. Using a SQUID magnetometer, magnetization versus magnetic field (M-H) curves of the round wires before and after sintering and reactive diffusion were measured at 5 K and in magnetic fields up to 5 T to define the J{sub cmag}. The direct current measurements were performed in self field at 4.2 K. A comparison between zero-field-cooled (ZFC) and field-cooled (FC) susceptibility measurements for sintered Ag/MgB{sub 2}, and reacted Cu/Mg + 2B conductors revealed systematic differences in the flux pinning in the wires which is in very good agreement with direct high transport current measurements. (author)

Superconductivity of powder-in-tube MgB{sub 2} wires

Energy Technology Data Exchange (ETDEWEB)

Glowacki, B.A.; Evetts, J.E. [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); Department of Materials Science and Metallurgy, Pembroke Street, Cambridge, CB2 3QZ (United Kingdom); Majoros, M. [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); Institute of Electrical Engineering, Slovak Academy of Science, Dubravska Cesta 9, Bratislava (Slovakia); Vickers, M. [Department of Materials Science and Metallurgy, Pembroke Street, Cambridge, CB2 3QZ (United Kingdom); Shi, Y. [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); McDougall, I. [Oxford Instruments Plc, Eynsham, OX8 ITL (United Kingdom)

2001-04-01

A new class of 'powder-in-tube' Mg-B superconducting conductors has been prepared using two different methods: an in situ technique where an Mg + 2B mixture was used as a central conductor core and reacted in situ to form MgB{sub 2}, and an ex situ technique where fully reacted MgB{sub 2} powder was used to fill the metal tube. Conductors were prepared using silver, copper and bimetallic silver/stainless steel tubes. Wires manufactured by the in situ technique, diffusing Mg to B particles experienced {approx}25.5% decrease in density from the initial value after cold deformation, due to the phase transformation from Mg + 2({beta}-B){yields}MgB{sub 2} all with hexagonal structure. A comparative study of the intergranular current and grain connectivity in wires was conducted by AC susceptibility measurements and direct four point transport measurements. Using a SQUID magnetometer, magnetization versus magnetic field (M-H) curves of the round wires before and after sintering and reactive diffusion were measured at 5 K and in magnetic fields up to 5 T to define the J{sub cmag}. The direct current measurements were performed in self field at 4.2 K. A comparison between zero-field-cooled (ZFC) and field-cooled (FC) susceptibility measurements for sintered Ag/MgB{sub 2}, and reacted Cu/Mg + 2B conductors revealed systematic differences in the flux pinning in the wires which is in very good agreement with direct high transport current measurements. (author)

Synthesis of a ruthenium(II) bipyridyl complex coordinated by a functionalized Schiff base ligand: characterization, spectroscopic and isothermal titration calorimetry measurements of M2+ binding and sensing (M2+=Ca2+, Mg2+).

Science.gov (United States)

Dixit, Namrata; Mishra, Lallan; Mustafi, Sourajit M; Chary, Kandala V R; Houjou, Hirohiko

2009-07-01

Bis-[methylsalicylidine-4'benzoic acid]-ethylene (LH2) complexed with cis-Ru(bpy)2Cl(2).2H2O provides a complex of composition [Ru(bpy)2L].2NH4PF6 (1), which has been characterized spectroscopically. Its binding behaviour towards Mg2+ and Ca2+ ions is monitored using 1H NMR titration, isothermal titration calorimetry (ITC) and luminescence microscopy. The luminescent ruthenium complex binds Ca2+ in a more selective manner as compared to Mg2+.

Ab-initio calculations of semiconductor MgGeP{sub 2} and MgGeAs{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Kocak, B.; Ciftci, Y.O., E-mail: yasemin@gazi.edu.tr

2016-05-15

Highlights: • MgGeP{sub 2} and MgGeAs{sub 2} are semiconductor compounds. • MgGeP{sub 2} and MgGeAs{sub 2} are energetically, mechanically and dynamically stable. • The electronic charge density contour plot shows that the nature of bonding is a mixture of ionic-covalent. - Abstract: In this study, we focus on structural, electronic, elastic, lattice dynamic and optic properties of MgGeP{sub 2} and MgGeAs{sub 2} using ab-initio density-functional theory (DFT) within Armiento-Mattson 2005 (AM05) scheme of the generalized gradient approximation (GGA) for the exchange-correlation potential. Our computed structural results are in reasonable agreement with the literature. The band gap of these compounds is predicted to be direct. Our elastic results prove that these compounds are mechanically stable. The obtained phonon spectra of MgGeP{sub 2} and MgGeAs{sub 2} do not exhibit any significant imaginary branches using GGA-AM05 for the exchange-correlation approximation. Further analysis of the optical response of the dielectric functions, optical reflectivity, refractive index, extinction coefficient and electron energy loss delves into for the energy range of 0–22.5 eV. It motivated that there exists an optical polarization anisotropy of these compounds for optoelectronic device applications.

A comparison of amorphous calcium carbonate crystallization in aqueous solutions of MgCl2 and MgSO4: implications for paleo-ocean chemistry

Science.gov (United States)

Han, Mei; Zhao, Yanyang; Zhao, Hui; Han, Zuozhen; Yan, Huaxiao; Sun, Bin; Meng, Ruirui; Zhuang, Dingxiang; Li, Dan; Liu, Binwei

2018-04-01

Based on the terminology of "aragonite seas" and "calcite seas", whether different Mg sources could affect the mineralogy of carbonate sediments at the same Mg/Ca ratio was explored, which was expected to provide a qualitative assessment of the chemistry of the paleo-ocean. In this work, amorphous calcium carbonate (ACC) was prepared by direct precipitation in anhydrous ethanol and used as a precursor to study crystallization processes in MgSO4 and MgCl2 solutions having different concentrations at 60 °C (reaction times 240 and 2880 min). Based on the morphology of the aragonite crystals, as well as mineral saturation indices and kinetic analysis of geochemical processes, it was found that these crystals formed with a spherulitic texture in 4 steps. First, ACC crystallized into columnar Mg calcite by nearly oriented attachment. Second, the Mg calcite changed from columnar shapes into smooth dumbbell forms. Third, the Mg calcite transformed into rough dumbbell or cauliflower-shaped aragonite forms by local dissolution and precipitation. Finally, the aragonite transformed further into spherulitic radial and irregular aggregate forms. The increase in Ca2+ in the MgSO4 solutions compared with the MgCl2 solutions indicates the fast dissolution and slow precipitation of ACC in the former solutions. The phase transition was more complete in the 0.005 M MgCl2 solution, whereas Mg calcite crystallized from the 0.005 M MgSO4 solution, indicating that Mg calcite could be formed more easily in an MgSO4 solution. Based on these findings, aragonite and Mg calcite relative to ACC could be used to provide a qualitative assessment of the chemistry of the paleo-ocean. Therefore, calcite seas relative to high-Mg calcite could reflect a low concentration MgSO4 paleo-ocean, while aragonite seas could be related to an MgCl2 or high concentration of MgSO4 paleo-ocean.

Mg2+ Effect on Argonaute and RNA Duplex by Molecular Dynamics and Bioinformatics Implications

Science.gov (United States)

Nam, Seungyoon; Ryu, Hyojung; Son, Won-joon; Kim, Yon Hui; Kim, Kyung Tae; Balch, Curt; Nephew, Kenneth P.; Lee, Jinhyuk

2014-01-01

RNA interference (RNAi), mediated by small non-coding RNAs (e.g., miRNAs, siRNAs), influences diverse cellular functions. Highly complementary miRNA-target RNA (or siRNA-target RNA) duplexes are recognized by an Argonaute family protein (Ago2), and recent observations indicate that the concentration of Mg2+ ions influences miRNA targeting of specific mRNAs, thereby modulating miRNA-mRNA networks. In the present report, we studied the thermodynamic effects of differential [Mg2+] on slicing (RNA silencing cycle) through molecular dynamics simulation analysis, and its subsequent statistical analysis. Those analyses revealed different structural conformations of the RNA duplex in Ago2, depending on Mg2+ concentration. We also demonstrate that cation effects on Ago2 structural flexibility are critical to its catalytic/functional activity, with low [Mg2+] favoring greater Ago2 flexibility (e.g., greater entropy) and less miRNA/mRNA duplex stability, thus favoring slicing. The latter finding was supported by a negative correlation between expression of an Mg2+ influx channel, TRPM7, and one miRNA’s (miR-378) ability to downregulate its mRNA target, TMEM245. These results imply that thermodynamics could be applied to siRNA-based therapeutic strategies, using highly complementary binding targets, because Ago2 is also involved in RNAi slicing by exogenous siRNAs. However, the efficacy of a siRNA-based approach will differ, to some extent, based on the Mg2+ concentration even within the same disease type; therefore, different siRNA-based approaches might be considered for patient-to-patient needs. PMID:25330448

Microwave absorption studies of MgB 2 superconductor

Indian Academy of Sciences (India)

Microwave absorption studies have been carried out on MgB2 superconductor using a standard X-band EPR spectrometer. The modulated low-field microwave absorption signals recorded for polycrystalline (grain size ∼ 10m) samples suggested the absence of weak-link character. The field dependent direct microwave ...

Geometry and bonding in the ground and lowest triplet state of D{sub 6h} symmetric crenellated edged C{sub 6[3m(m-1)+1]}H{sub 6(2m-1)} (m = 2,..., 6) graphene hydrocarbon molecules

Energy Technology Data Exchange (ETDEWEB)

Philpott, Michael R., E-mail: philpott@imr.edu [Center for Computational Materials Science, Institute of Materials Science, Tohoku University, 2-1-1 Katahira, Aoba-ku, 980-8577 Sendai (Japan); Kawazoe, Yoshiyuki [Center for Computational Materials Science, Institute of Materials Science, Tohoku University, 2-1-1 Katahira, Aoba-ku, 980-8577 Sendai (Japan)

2009-03-30

Ab initio plane wave all valence electron based DFT calculations were used to explore the dichotomy of perimeter vs. interior in the electronic and geometric structure of the D{sub 6h} singlet ground state and D{sub 2h} lowest triplet state of planar graphene hydrocarbon molecules with crenellated (arm chair) edges and the general formula C{sub 6[3m(m-1)+1]} H{sub 6(2m-1)} where m = 2,...,6. The largest molecule C{sub 546}H{sub 66} was 4.78 nm across and contained 2250 valence electrons. These molecules are nominally 'fully benzenoid hydrocarbons'. However with increasing size, the core of central atoms abandoned any fully benzenoid geometry they had in small systems and organized into single layer graphite (graphene) structure. The perimeter atoms of the crenellation adopted a conjugated geometry with unequal bonds and between core and perimeter there were some C{sub 6} rings retaining remnants of aromatic sextet-type properties. Compared to a zigzag edge the crenellated edge conferred stability in all the systems studied as measured by the singlet homo-lumo level gap BG{sub 0} and the singlet-lowest triplet energy gap {Delta}E{sub ST}. For the largest crenellated system (m = 6) BG{sub 0} and {Delta}E{sub ST} were approximately 0.7 eV, larger in value than for similarly sized hexagonal graphenes with zigzag edges. Triplet states were identified for all the molecules in the series and in the case of the m = 2 molecule hexabenzocoronene C{sub 42}H{sub 18}, two conformations with D{sub 2h} symmetry were identified and compared to features on the triplet state potential energy surface of benzene.

Alterations of Mg2+ After Hemorrhagic Shock.

Science.gov (United States)

Lee, Mun-Young; Yang, Dong Kwon; Kim, Shang-Jin

2017-11-01

Hemorrhagic shock is generally characterized by hemodynamic instability with cellular hypoxia and diminishing cellular function, resulting from an imbalance between systemic oxygen delivery and consumption and redistribution of fluid and electrolytes. Magnesium (Mg) is the fourth most abundant cation overall and second most abundant intracellular cation in the body and an essential cofactor for the energy production and cellular metabolism. Data for blood total Mg (tMg; free-ionized, protein-bound, and anion-bound forms) and free Mg 2+ levels after a traumatic injury are inconsistent and only limited information is available on hemorrhagic effects on free Mg 2+ as the physiologically active form. The aim of this study was to determine changes in blood Mg 2+ and tMg after hemorrhage in rats identifying mechanism and origin of the changes in blood Mg 2+ . Hemorrhagic shock produced significant increases in blood Mg 2+ , plasma tMg, Na + , K + , Cl - , anion gap, partial pressures of oxygen, glucose, and blood urea nitrogen but significant decreases in RBC tMg, blood Ca 2+ , HCO 3 - , pH, partial pressures of carbon dioxide, hematocrit, hemoglobin, total cholesterol, and plasma/RBC ATP. During hemorrhagic shock, K + , anion gap, and BUN showed significant positive correlations with changes in blood Mg 2+ level, while Ca 2+ , pH, and T-CHO correlated to Mg 2+ in a negative manner. In conclusion, hemorrhagic shock induced an increase in both blood-free Mg 2+ and tMg, resulted from Mg 2+ efflux from metabolic damaged cell with acidosis and ATP depletion.

Electric conductivity of solid solutions the Cs3-2xMxPO4 (M=Ba, Sr, Ca, Mg) systems

International Nuclear Information System (INIS)

Burmakin, E.I.; Stroev, S.S.; Shekhtman, G.Sh.; Antonov, B.D.

2003-01-01

The solid solutions in the Cs 3-2x M x PO 4 (M=Ba, Sr, Ca, Mg) system are synthesized and their thermal behavior and electric conductivity are studied. The introduction of the alkaline earth metal cations into cesium orthophosphates is accompanied by the shift of the phase transition occurring in the pure Cs 3 PO 4 at 450-620 Deg C into the low-temperature area as well as by increase in the cesium-cation conductivity at low temperatures. The electric conductivity in the area of existence of the Cs 3 PO 4 high-temperature modification slightly depends on the availability and concentration of the modifying additions, which make it possible to suppose the calcium sublattice structural disordering [ru

Superconducting properties of MgB2 particle impregnated with Mg-based alloys

International Nuclear Information System (INIS)

Shimizu, Yusuke; Matsuda, Kenji; Mizutani, Manabu; Nishimura, Katsuhiko; Kawabata, Tokimasa; Ikeno, Susumu; Hishinuma, Yoshimitsu; Aoyama, Shigeki

2011-01-01

The three-dimensional penetration method combined with semi-solid casting (SS-3DPC) was utilized to prepare magnesium diboride (MgB 2 ) powder composite materials with various host materials of Mg, Mg-3%Al, Mg-3%Al-1%Zn, Mg-9%Al, and Mg-9%Al-1%Zn. X-ray diffraction measurements indicated predominant peak patterns of MgB 2 and a host alloy, implying that the host material tightly bonded MgB 2 grains without melting the MgB 2 powder. This was confirmed by SEM images. Measured electrical resistivity and magnetization versus temperature showed clear signals of superconducting transition temperature of 27-38 K for all the samples cut out from the billets. Magnetic hysteresis loop observed at 5 K enabled us to estimate a critical current density (J c ) based on the extended Bean model. Additions of aluminum and zinc elements to magnesium host-matrix were found to enhance J c and increase residual resistivity (ρ 0 ) suggesting that aluminum and zinc have an effect on pinning magnetic flux flow for J c enhancement, and scattering conduction electrons for increase of ρ 0 . (author)

ß-Adrenergic stimulation increases RyR2 activity via intracellular Ca2+ and Mg2+ regulation.

Directory of Open Access Journals (Sweden)

Jiao Li

Full Text Available Here we investigate how ß-adrenergic stimulation of the heart alters regulation of ryanodine receptors (RyRs by intracellular Ca(2+ and Mg(2+ and the role of these changes in SR Ca(2+ release. RyRs were isolated from rat hearts, perfused in a Langendorff apparatus for 5 min and subject to 1 min perfusion with 1 µM isoproterenol or without (control and snap frozen in liquid N2 to capture their phosphorylation state. Western Blots show that RyR2 phosphorylation was increased by isoproterenol, confirming that RyR2 were subject to normal ß-adrenergic signaling. Under basal conditions, S2808 and S2814 had phosphorylation levels of 69% and 15%, respectively. These levels were increased to 83% and 60%, respectively, after 60 s of ß-adrenergic stimulation consistent with other reports that ß-adrenergic stimulation of the heart can phosphorylate RyRs at specific residues including S2808 and S2814 causing an increase in RyR activity. At cytoplasmic [Ca(2+] 1 µM, ß-adrenergic stimulation only decreased cytoplasmic Mg(2+ and Ca(2+ inhibition of RyRs. The Ka and maximum levels of cytoplasmic Ca(2+ activation site were not affected by ß-adrenergic stimulation. Our RyR2 gating model was fitted to the single channel data. It predicted that in diastole, ß-adrenergic stimulation is mediated by 1 increasing the activating potency of Ca(2+ binding to the luminal Ca(2+ site and decreasing its affinity for luminal Mg(2+ and 2 decreasing affinity of the low-affinity Ca(2+/Mg(2+ cytoplasmic inhibition site. However in systole, ß-adrenergic stimulation is mediated mainly by the latter.

Effect of the La/Mg ratio on the structure and electrochemical properties of La xMg 3- xNi 9 ( x=1.6-2.2) hydrogen storage electrode alloys for nickel-metal hydride batteries

Science.gov (United States)

Liao, B.; Lei, Y. Q.; Chen, L. X.; Lu, G. L.; Pan, H. G.; Wang, Q. D.

Effect of La/Mg ratio on the structure and electrochemical properties of La xMg 3- xNi 9 ( x=1.6-2.2) ternary alloys was investigated. All alloys are consisted of a main phase with hexagonal PuNi 3-type structure and a few impurity phases (mainly LaNi 5 and MgNi 2). The increase of La/Mg ratio in the alloys leads to an increase in both the cell volume and the hydride stability. The discharge capacity of the alloys at 100 mA/g increases with the increase of La/Mg ratio and passes though a maximum of 397.5 mAh/g at x=2.0. As the La/Mg ratio increases, the high-rate dischargeability of the alloy electrodes at 1200 mA/g HRD 1200 decreases from 66.7% ( x=1.6) to 26.5% ( x=2.2). The slower decrease of HRD 1200 (from 66.7 to 52.7%) of the alloys with x=1.6-2.0 is mainly attributed to the decrease of electrocatalytic activity of the alloys for charge-transfer reaction, the more rapid decrease of HRD 1200 of the alloys with x>2.0 is mainly attributed to the lowering of the hydrogen diffusion rate in the bulk of alloy. The cycling capacity degradation of the alloys is rather fast for practical application due to the corrosion of La and Mg and the large VH in the hydride phase.

The M/G/1 queue with quasi-restricted accessibility

NARCIS (Netherlands)

Boxma, O.J.; Perry, D.; Stadje, W.; Zacks, S.

2009-01-01

We consider single-server queues of the M/G/1 kind with a special kind of partial customer rejection called quasi-restricted accessibility (QRA). Under QRA, the actual service time assigned to an arriving customer depends on his service requirement, say x, the current workload, say w, and a

Microwave assisted rapid growth of Mg(OH){sub 2} nanosheet networks for ethanol chemical sensor application

Energy Technology Data Exchange (ETDEWEB)

Al-Hazmi, Faten [Department of Physics, College of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21569 (Saudi Arabia); Umar, Ahmad, E-mail: ahmadumar786@gmail.com [Promising Centre for Sensors and Electronic Devices (PCSED) and Centre for Advanced Materials and Nano-Research (CAMNR), Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Dar, G.N. [Promising Centre for Sensors and Electronic Devices (PCSED) and Centre for Advanced Materials and Nano-Research (CAMNR), Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Al-Ghamdi, A.A.; Al-Sayari, S.A. [Department of Physics, College of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21569 (Saudi Arabia); Al-Hajry, A. [Promising Centre for Sensors and Electronic Devices (PCSED) and Centre for Advanced Materials and Nano-Research (CAMNR), Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Department of Physics, College of Science and Arts, Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Kim, S.H. [Promising Centre for Sensors and Electronic Devices (PCSED) and Centre for Advanced Materials and Nano-Research (CAMNR), Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Al-Tuwirqi, Reem M. [Department of Physics, College of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21569 (Saudi Arabia); Alnowaiserb, Fowzia [Department of Chemistry, Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia); El-Tantawy, Farid [Department of Physics, Faculty of Science, Suez Canal University, Ismailia (Egypt)

2012-04-05

Highlights: Black-Right-Pointing-Pointer A facile microwave-assisted synthesis and characterizations of magnesium hydroxide (Mg(OH){sub 2}) nanosheet networks. Black-Right-Pointing-Pointer Fabrication of ethanol sensor based on (Mg(OH){sub 2}) nanosheet networks. Black-Right-Pointing-Pointer Good sensitivity ({approx}3.991 {mu}A cm{sup -2} mM{sup -1}) and lower detection limit (5 {mu}M). Black-Right-Pointing-Pointer This research opens a way to utilize Mg(OH){sub 2} nanostructures for chemical sensors applications. - Abstract: This paper reports a facile microwave-assisted synthesis of magnesium hydroxide (Mg(OH){sub 2}) nanosheet networks and their utilization for the fabrication of efficient ethanol chemical sensor. The synthesized nanosheets networks were characterized in terms of their morphological, structural and optical properties using various analysis techniques such as field emission scanning electron microscopy (FESEM), X-ray diffraction pattern (XRD), Fourier transform infrared (FTIR) and UV-Vis spectroscopy. The detailed morphological and structural investigations reveal that the synthesized (Mg(OH){sub 2}) products are nanosheet networks, grown in high density, and possessing hexagonal crystal structure. The optical band gap of as-synthesized Mg(OH){sub 2} nanosheet networks was examined by UV-Vis absorption spectrum, and found to be 5.76 eV. The synthesized nanosheet networks were used as supporting matrices for the fabrication of I-V technique based efficient ethanol chemical sensor. The fabricated ethanol sensor based on nanosheet networks exhibits good sensitivity ({approx}3.991 {mu}A cm{sup -2} mM{sup -1}) and lower detection limit (5 {mu}M), with linearity (R = 0.9925) in short response time (10.0 s). This work demonstrate that the simply synthesized Mg(OH){sub 2} nanosheet networks can effectively be used for the fabrication of efficient ethanol chemical sensors.

The existence and stability of the anions matching the MFk+2- formula (M = Li, Na, K, Be, Mg, Ca, B, Al, Ga)

Science.gov (United States)

Marchaj, Marzena; Freza, Sylwia; Skurski, Piotr

2013-02-01

The electronic stabilities of the MFk+2- anions (where M = Li, Na, K, Be, Mg, Ca, B, Al, Ga; and k is the maximal formal valence of atom M) were investigated at the OVGF/6-311 + G(3df) level. The vertical electron detachment energies (VDE) of the anions examined were found to be large (7.1-10.1 eV) albeit not significantly exceeding those for the corresponding MFk+1- superhalogen anions. Even though all the MFk+2- species studied were predicted to be both geometrically and electronically stable, some of them turned out to be thermodynamically unstable (i.e., susceptible to the F atom loss).

Defect kinetics in spinels: Long-time simulations of MgAl2O4, MgGa2O4, and MgIn2O4

International Nuclear Information System (INIS)

Uberuaga, B. P.; Voter, A. F.; Sickafus, K. E.; Bacorisen, D.; Smith, Roger; Ball, J. A.; Grimes, R. W.

2007-01-01

Building upon work in which we examined defect production and stability in spinels, we now turn to defect kinetics. Using temperature accelerated dynamics (TAD), we characterize the kinetics of defects in three spinel oxides: magnesium aluminate MgAl 2 O 4 , magnesium gallate MgGa 2 O 4 , and magnesium indate MgIn 2 O 4 . These materials have varying tendencies to disorder on the cation sublattices. In order to understand chemical composition effects, we first examine defect kinetics in perfectly ordered, or normal, spinels, focusing on point defects on each sublattice. We then examine the role that cation disorder has on defect mobility. Using TAD, we find that disorder creates local environments which strongly trap point defects, effectively reducing their mobility. We explore the consequences of this trapping via kinetic Monte Carlo (KMC) simulations on the oxygen vacancy (V O ) in MgGa 2 O 4 , finding that V O mobility is directly related to the degree of inversion in the system

Influences of Mg Doping on the Electrochemical Performance of TiO2 Nanodots Based Biosensor Electrodes

Directory of Open Access Journals (Sweden)

M. S. H. Al-Furjan

2014-01-01

Full Text Available Electrochemical biosensors are essential for health monitors to help in diagnosis and detection of diseases. Enzyme adsorptions on biosensor electrodes and direct electron transfer between them have been recognized as key factors to affect biosensor performance. TiO2 has a good protein adsorption ability and facilitates having more enzyme adsorption and better electron transfer. In this work, Mg ions are introduced into TiO2 nanodots in order to further improve electrode performance because Mg ions are considered to have good affinity with proteins or enzymes. Mg doped TiO2 nanodots on Ti substrates were prepared by spin-coating and calcining. The effects of Mg doping on the nanodots morphology and performance of the electrodes were investigated. The density and size of TiO2 nanodots were obviously changed with Mg doping. The sensitivity of 2% Mg doped TiO2 nanodots based biosensor electrode increased to 1377.64 from 897.8 µA mM−1 cm−2 and its KMapp decreases to 0.83 from 1.27 mM, implying that the enzyme achieves higher catalytic efficiency due to better affinity of the enzyme with the Mg doped TiO2. The present work could provide an alternative to improve biosensor performances.

Thermodynamics of HEDPA protonation in different media and complex formation with Mg2+ and Ca2+

International Nuclear Information System (INIS)

Foti, Claudia; Giuffrè, Ottavia; Sammartano, Silvio

2013-01-01

Highlights: • Acid–base properties of etidronic acid in different ionic media and at different ionic strengths. • Complex formation of etidronate with Na + , K + , Ca 2+ and Mg 2+ . • Dependence on ionic strength analysed by a Debye–Hückel type equation and the SIT approach. • Suggested protonation constants calculated at I = 0.1 mol · L −1 and t = 25 °C, in different ionic media. -- Abstract: Acid–base properties of etidronic acid [(1-Hydroxyethane-1,1-diyil)bis(phosphonic acid), HEDPA] in different ionic media and at different ionic strengths (NaCl, KCl: I ⩽ 2 mol · L −1 ; (C 2 H 5 ) 4 NI: I ⩽ 1 mol · L −1 ) were studied at t = 25 °C, determining, by potentiometric and calorimetric techniques, protonation constants and enthalpy changes. The differences in the protonation constants in the different supporting electrolytes were also interpreted in terms of weak complex formation with M i L (with i = 1, 2), MLH j (with j = 1, 2, 3) and M 2 LH species (with L = HEDPA; M = Na + , K + ). The formation constants for the species of Ca 2+ and Mg 2+ , were determined by potentiometric titrations at different ionic strengths (0.1 ⩽ I/mol · L −1 ⩽ 1) in NaCl at t = 25 °C. The stability of these species is fairly high, as an example, at I = 0.1 mol · L −1 and t = 25 °C, for ML species, log β = 6.52 and 6.86, for Ca 2+ and Mg 2+ , respectively, obtained by considering simultaneously HEDPA–Na + interactions. The dependence on ionic strength was analysed by a Debye–Hückel type equation and the SIT (Specific ion Interaction Theory) approach for protonation thermodynamic parameters and by a Debye–Hückel type equation for Mg 2+ and Ca 2+ complex formation. The sequestering ability of HEDPA toward Ca 2+ and Mg 2+ was also analysed. A comparison with literature data is given

The effects of Fe2O3 nanoparticles on MgB2 superconducting thin films

International Nuclear Information System (INIS)

Koparan, E.T.; Sidorenko, A.; Yanmaz, E.

2013-01-01

Full text: Since the discovery of superconductivity in binary MgB 2 compounds, extensive studies have been carried out because of its excellent properties for technological applications, such as high transition temperature (T c = 39 K), high upper critical field (H c2 ), high critical current density (J c ). Thin films are important for fundamental research as well as technological applications of any functional materials. Technological applications primarily depend on critical current density. The strong field dependence of J c for MgB 2 necessitates an enhancement in flux pinning performance in order to improve values in high magnetic fields. An effective way to improve the flux pinning is to introduce flux pinning centers into MgB 2 through a dopant having size comparable to the coherence length of MgB 2 . In this study, MgB 2 film with a thickness of about 600 nm was deposited on the MgO (100) single crystal substrate using a 'two-step' synthesis technique. Firstly, deposition of boron thin film was carried out by rf magnetron sputtering on MgO substrates and followed by a post deposition annealing at 850 degrees Celsius in magnesium vapour. In order to investigate the effect of Fe 2 O 3 nanoparticles on the structural and magnetic properties of films, MgB 2 films were coated with different concentrations of Fe 2 O 3 nanoparticles by a spin coating process. The effects of different concentrations of ferromagnetic Fe 2 O 3 nanoparticles on superconducting properties of obtained films were carried out by using structural (XRD, SEM, AFM), electrical (R-T) and magnetization (M-H, M-T and AC Susceptibility) measurements. It was calculated that anisotropic coefficient was about γ = 1.2 and coherence length of 5 nm for the uncoated film. As a result of coherence length, the appropriate diameters of Fe 2 O 3 nanoparticles were found to be 10 nm, indicating that these nanoparticles served as the pinning centers. Based on the data obtained from this study, it can be

Effect of Mg(2+), Ca(2+), Sr(2+) and Ba(2+) metal ions on the antifungal activity of ZnO nanoparticles tested against Candida albicans.

Science.gov (United States)

Haja Hameed, Abdulrahman Syedahamed; Karthikeyan, Chandrasekaran; Senthil Kumar, Venugopal; Kumaresan, Subramanian; Sasikumar, Seemaisamy

2015-01-01

The antifungal ability of pure and alkaline metal ion (Mg(2+), Ca(2+), Sr(2+) and Ba(2+)) doped ZnO nanoparticles (NPs) prepared by the co-precipitation method was tested against the pathogenic yeast, Candida albicans (C. albicans), and the results showed that the Mg-doped ZnO NPs possessed greater effect than the other alkaline metal ion doped ZnO NPs. The impact of the concentration of Mg doped ZnO sample on the growth of C. albicans was also studied. The Minimal Fungicidal Concentration (MFC) of the Mg doped ZnO NPs was found to be 2000 μg/ml for which the growth of C. albicans was completely inhibited. The ZnO:Mg sample (1.5mg/ml) with various concentrations of histidine reduced the fungicidal effect of the nanoparticles against C. albicans, which was deliberately explained by the role of ROS. The ZnO:Mg sample added with 5mM of histidine scavenged the ample amount of generated ROS effectively. The binding of the NPs with fungi was observed by their FESEM images and their electrostatic attraction is confirmed by the zeta potential measurement. Copyright © 2015. Published by Elsevier B.V.

First-principle Calculations of Mechanical Properties of Al2Cu, Al2CuMg and MgZn2 Intermetallics in High Strength Aluminum Alloys

Directory of Open Access Journals (Sweden)

LIAO Fei

2016-12-01

Full Text Available Structural stabilities, mechanical properties and electronic structures of Al2Cu, Al2CuMg and MgZn2 intermetallics in Al-Zn-Mg-Cu aluminum alloys were determined from the first-principle calculations by VASP based on the density functional theory. The results show that the cohesive energy (Ecoh decreases in the order MgZn2 > Al2CuMg > Al2Cu, whereas the formation enthalpy (ΔH decreases in the order MgZn2 > Al2Cu > Al2CuMg. Al2Cu can act as a strengthening phase for its ductile and high Young's modulus. The Al2CuMg phase exhibits elastic anisotropy and may act as a crack initiation point. MgZn2 has good plasticity and low melting point, which is the main strengthening phase in the Al-Zn-Mg-Cu aluminum alloys. Metallic bonding mode coexists with a fractional ionic interaction in Al2Cu, Al2CuMg and MgZn2, and that improves the structural stability. In order to improve the alloys' performance further, the generation of MgZn2 phase should be promoted by increasing Zn content while Mg and Cu contents are decreased properly.

Inhibitory effect of high [Mg2+] on the vasopressin-stimulated hydroosmotic permeability of the isolated perfused cortical collecting duct

Directory of Open Access Journals (Sweden)

Falkenstein D.

1999-01-01

Full Text Available High magnesium concentration inhibits the effect of arginine vasopressin (AVP on smooth muscle contraction and platelet aggregation and also influences hepatocyte AVP receptor binding. The aim of this study was to determine the role of magnesium concentration [Mg2+] in AVP-stimulated water transport in the kidney collecting duct. The effect of low and high peritubular [Mg2+] on the AVP-stimulated osmotic water permeability coefficient (Pf was evaluated in the isolated perfused rabbit cortical collecting duct (CCD. Control tubules bathed and perfused with standard Ringer bicarbonate solution containing 1 mM Mg2+ presented a Pf of 223.9 ± 27.2 µm/s. When Mg2+ was not added to the bathing solution, an increase in the AVP-stimulated Pf to 363.1 ± 57.2 µm/s (P<0.05 was observed. An elevation of Mg2+ to 5 mM resulted in a decrease in Pf to 202.9 ± 12.6 µm/s (P<0.05. This decrease in the AVP-stimulated Pf at 5 mM Mg2+ persisted when the CCDs were returned to 1 mM Mg2+, Pf = 130.2 ± 20.3 µm/s, and was not normalized by the addition of 8-[4-chlorophenylthio]-adenosine 3',5'-cyclic monophosphate, a cAMP analogue, to the preparation. These data indicate that magnesium may play a modulatory role in the action of AVP on CCD osmotic water permeability, as observed in other tissues.

ALUMINUM CHLORIDE EFFECT ON Ca2+,Mg(2+)-ATPase ACTIVITY AND DYNAMIC PARAMETERS OF SKELETAL MUSCLE CONTRACTION.

Science.gov (United States)

Nozdrenko, D M; Abramchuk, O M; Soroca, V M; Miroshnichenko, N S

2015-01-01

We studied enzymatic activity and measured strain-gauge contraction properties of the frog Rana temporaria m. tibialis anterior muscle fascicles during the action of aluminum chloride solution. It was shown that AlCl3 solutions did not affect the dynamic properties of skeletal muscle preparation in concentrations less than 10(-4) M Increasing the concentration of AlCl3 to 10(-2) M induce complete inhibition of muscle contraction. A linear correlation between decrease in Ca2+,Mg(2+)-ATPase activity of sarcoplasmic reticulum and the investigated concentrations range of aluminum chloride was observed. The reduction in the dynamic contraction performance and the decrease Ca2+,Mg(2+)-ATPase activity of the sarcoplasmic reticulum under the effect of the investigated AlCl3 solution were minimal in pre-tetanus period of contraction.

Aluminum chloride effect on Ca(2+,Mg(2+-ATPase activity and dynamic parameters of skeletal muscle contraction

Directory of Open Access Journals (Sweden)

D. M. Nozdrenko

2015-10-01

Full Text Available We studied enzymatic activity and measured strain-gauge contraction properties of the frog Rana temporaria m. tibialis anterior muscle fascicles during the action of aluminum chloride solution. It was shown that AlCl3 solutions did not affect the dynamic properties of skeletal muscle preparation in concentrations less than 10-4 M. Increasing the concentration of AlCl3 to 10-2 M induce complete inhibition of muscle contraction. A linear correlation between decrease in Ca2+,Mg2+-ATPase activity of sarcoplasmic reticulum and the investigated concentrations range of aluminum chloride was observed. The reduction in the dynamic contraction performance and the decrease Ca2+,Mg2+-ATPase activity of the sarcoplasmic reticulum under the effect of the investigated AlCl3 solution were minimal in pre-tetanus period of contraction.

Photoluminescence of Mg-doped m-plane GaN grown by MOCVD on bulk GaN substrates

OpenAIRE

Monemar, Bo; Paskov, Plamen; Pozina, Galia; Hemmingsson, Carl; Bergman, Peder; Lindgren, David; Samuelson, Lars; Ni, Xianfeng; Morkoç, Hadis; Paskova, Tanya; Bi, Zhaoxia; Ohlsson, Jonas

2011-01-01

Photoluminescence (PL) properties are reported for a set of m-plane GaN films with Mg doping varied from mid 1018cm-3 to well above 1019 cm-3. The samples were grown with MOCVD at reduced pressure on low defect density m-plane bulk GaN templates. The sharp line near bandgap bound exciton (BE) spectra observed below 50 K, as well as the broader donor-acceptor pair (DAP) PL bands at 2.9 eV to 3.3 eV give evidence of several Mg related acceptors, similar to the case of c-plane GaN. The dependenc...

Modelling M/G/1 queueing systems with server vacations using ...

African Journals Online (AJOL)

Simple numerical examples are also provided to illustrate the func- ... M/G/1/N queueing systems with server vacations under a limited service discipline ...... system contents in a discrete-time non-preemptive priority queue with general service.

Novel ZnO/MgO/Fe2O3 composite optomagnetic nanoparticles

International Nuclear Information System (INIS)

Kamińska, I; Sikora, B; Fronc, K; Dziawa, P; Sobczak, K; Minikayev, R; Paszkowicz, W; Elbaum, D

2013-01-01

A facile sol–gel synthesis of novel ZnO/MgO/Fe 2 O 3 nanoparticles (NPs) is reported and their performance is compared to that of ZnO/MgO. Powder x-ray diffraction (XRD) patterns reveal the crystal structure of the prepared samples. The average particle size of the sample was found to be 4.8 nm. The optical properties were determined by UV–vis absorption and fluorescence measurements. The NPs are stable in biologically relevant solutions (phosphate buffered saline (PBS), 20 mM, pH = 7.0) contrary to ZnO/MgO NPs which degrade in the presence of inorganic phosphate. Superparamagnetic properties were determined with a superconducting quantum interference device (SQUID). Biocompatible and stable in PBS ZnO/MgO/Fe 2 O 3 core/shell composite nanocrystals show luminescent and magnetic properties confined to a single NP at room temperature (19–24 ° C), which may render the material to be potentially useful for biomedical applications. (paper)

Electron paramagnetic resonance study of neutral Mg acceptors in β-Ga2O3 crystals

Science.gov (United States)

Kananen, B. E.; Halliburton, L. E.; Scherrer, E. M.; Stevens, K. T.; Foundos, G. K.; Chang, K. B.; Giles, N. C.

2017-08-01

Electron paramagnetic resonance (EPR) is used to directly observe and characterize neutral Mg acceptors ( M gGa0 ) in a β-Ga2O3 crystal. These acceptors, best considered as small polarons, are produced when the Mg-doped crystal is irradiated at or near 77 K with x rays. During the irradiation, neutral acceptors are formed when holes are trapped at singly ionized Mg acceptors ( M gGa- ). Unintentionally present Fe3+ (3d5) and Cr3+ (3d3) transition-metal ions serve as the corresponding electron traps. The hole is localized in a nonbonding p orbital on a threefold-coordinated oxygen ion adjacent to an Mg ion at a sixfold-coordinated Ga site. These M gGa0 acceptors (S = 1/2) have a slightly anisotropic g matrix (principal values are 2.0038, 2.0153, and 2.0371). There is also partially resolved 69Ga and 71Ga hyperfine structure resulting from unequal interactions with the two Ga ions adjacent to the hole. With the magnetic field along the a direction, hyperfine parameters are 2.61 and 1.18 mT for the 69Ga nuclei at the two inequivalent neighboring Ga sites. The M gGa0 acceptors thermally convert back to their nonparamagnetic M gGa- charge state when the temperature of the crystal is raised above approximately 250 K.

Ab initio study of MgH2 formation

International Nuclear Information System (INIS)

Novakovic, Nikola; Matovic, Ljiljana; Novakovic, Jasmina Grbovic; Manasijevic, Miodrag; Ivanovic, Nenad

2009-01-01

Even if there is considerable literature dealing with structure and properties of MgH 2 compound there are still some uncertain details about nature of bonding governing its formation and decomposition. In order to better understand the processes essential for absorption and desorption of MgH 2 , ab initio DFT based calculations of rutile MgH 2 compound, elemental hcp-Mg, and three different hypothetical hcp-Mg-derived hydrides are performed. Our findings show that all structures are unstable, and that MgH (Wurtzite) is a closest possible candidate for intermediate phase between the hcp-Mg and MgH 2 at 1:1 stoichiometry. An alternative hydration pathway is suggested, including promotion of hcp-Mg to bcc-Mg and consecutive transformation to rutile MgH 2 by means of hydrogen incorporation into Mg matrix. Rutile MgH 2 calculations with various hydrogen vacancies concentration are performed. Calculation shows that at high hydrogen concentration close to 1:2, stable substoichiometric hydride is possible. Calculation also shows that high vacancy (low hydrogen) concentration favors bcc-Mg 2 H over rutile Mg 2 H structure.

Stability of a1 mg/mL oral solution zidovudine

International Nuclear Information System (INIS)

Garcia Penna, Caridad Margarita; Morales Lacarrere, Ivan; Martinez Espinosa, Vivian

2011-01-01

The carrying out of a high-performance liquid chromatography analytical method was assessed; applicable to stability study of oral solution zidovudine (1 mg/mL) was made. The analytical method was linear, precise, specific and exact in the study concentrations. The stability study of oral solution zidovudine (1 mg/mL) was conducted determining expiring date. The shelf life study was conducted over 24 months at room temperature; whereas that of accelerated stability was conducted with the product under wet and temperature conditions; analysis was carried out over three months. Formula met quality specifications described in Pharmacopeia. Results from the shelf life study demonstrated that product keeps the parameters determining its quality during that time and in accelerated studies there was not significant product degradation. Under above mentioned conditions two years were established as expiring date

Ground motion attenuation during M 7.1 Darfield and M 6.2 Christchurch, New Zealand, earthquakes and performance of global Ppedictive models

Science.gov (United States)

Segou, Margaret; Kalkan, Erol

2011-01-01

fault with M 6.2, followed by a second event (M 6.9), releasing the largest portion of the energy on the right-lateral Greendale fault. The third sub-event (M 5.7) is due to a reverse fault with a right-lateral component (Holden et al. 2011). The Christchurch earthquake occurred on an oblique thrust fault. The comparison of spectral acceleration values at stations near Christchurch reveals that the second event produced much larger amplitudes of shaking than the Darfield event due to its proximity to the epicenter. Both events resulted in noticeably large amplitudes of the vertical motion, often exceeding horizontal motion in the near-fault area. The vertical motions, showing asymmetric acceleration traces and pulses, reached 1.26 g during the Darfield earthquake and 2.2 g during the Christchurch event. These events were recorded by more than 100 strong motion stations operated by the Institute of Geological and Nuclear Sciences (http://www.geonet.org.nz/). Using the processed data from these stations, peak ground acceleration (PGA) and 5%-damped spectral acceleration values at 0.3, 1, and 3 s are used for performance evaluation of the global ground motion predictive equations (GMPEs). The selected GMPEs are the Next Generation Attenuation (NGA) models of Abrahamson and Silva (2008), Boore and Atkinson (2008), Campbell and Bozorgnia (2008), and Chiou and Youngs (2008). The Graizer and Kalkan (2007, 2009) model, which is based on the NGA project database, is also included. These GMPEs are abbreviated respectively as AS08, BA08, CB08, CY08, and GK07. Because they have been used widely for seismic hazard analysis for crustal earthquakes, their performance assessment becomes a critical issue especially for immediate response and recovery planning after major events. The occurrence of aftershocks similar to the Christchurch event will most probably control seismic hazard in the broader area, as confirmed by the recent M 6.0 event on June 13, 2011.

Design of MgB2 Superconducting coils for the Ignitor Experiment*

Science.gov (United States)

Grasso, G.; Penco, R.; Berta, S.; Coppi, B.; Giunchi, G.

2009-11-01

A feasibility study for the adoption of MgB2 superconducting cables for the largest (about 5 m in diameter) of the poloidal field coils of the Ignitor machine is being carried out. This initiative was prompted by the progress made in the fabrication of MgB2 long cables, and related superconducting magnets of relatively large dimensions. These magnets will be cryocooled at the operating temperature of 10-15 K that is compatible with the He-gas cryogenic cooling system of Ignitor as well as with the projected superconducting current density of the MgB2 material, at the magnetic field values (˜4-5 T) in which these coils are designed to operate. The optimal cable configuration has been identified that can provide an efficient cooling of the MgB2 conductors over times compatible with the machine duty cycles. MgB2 superconductors hold the promise of becoming suitable for high field magnets by appropriate doping of the material and of replacing gradually the normal conducting coils adopted, by necessity, in high field experiments. Therefore, an appropriate R&D program on the development of improved MgB2 material and related superconducting cabling options has been undertaken, involving different institutions.

MgB2 thick films on three-dimensional structures fabricated by HPCVD

Science.gov (United States)

Guo, Zhengshan; Cai, Xingwei; Liao, Xuebin; Chen, Yiling; Yang, Can; Niu, Ruirui; Luo, Wenhao; Huang, Zigeng; Feng, Qingrong; Gan, Zizhao

2018-06-01

Magnetic shielding has been a key factor in the measurement of ultra-weak magnetic fields, especially for shielding from low frequency electromagnetic noise. With the recent development of superconducting quantum interference devices, superconducting magnetic shielding has become an important area of research. MgB2 has shown great potential in magnetic shielding for its remarkable superconducting properties, the feasibility of its use in this capacity having been demonstrated by MgB2 bulk samples. However, the potential for application of such bulk samples is limited. In this work, we have investigated the possibility of the fabrication of MgB2 films on three-dimensional (3D) structures using a hybrid physical‑chemical vapor deposition system. MgB2 films 10 μm thick have been fabricated on the outer surface of a polycrystalline Al2O3 cylinder. The deposited film showed a transition temperature (TC) of 39 K and J C of 5.1 × 105 A · cm‑2, which are comparable to those of planar MgB2 films. This work shows the feasibility of depositing MgB2 films onto a 3D structure, and sheds light on the potential use of MgB2 films in superconducting magnetic shielding.

Proteome of Salmonella Enterica SerotypeTyphimurium Grown in a Low Mg2+/pH Medium

Energy Technology Data Exchange (ETDEWEB)

Shi, Liang; Ansong, Charles; Smallwood, Heather S.; Rommereim, Leah M.; McDermott, Jason E.; Brewer, Heather M.; Norbeck, Angela D.; Taylor, Ronald C.; Gustin, Jean K.; Heffron, Fred; Smith, Richard D.; Adkins, Joshua N.

2009-09-01

The facultative intracellular pathogen Salmonella enterica serovar Typhimurium (STM) must replicate within host macrophages in order to establish systemic infection in susceptible mice. In an effort to identify new STM proteins that help the bacterium colonize macrophages, we have cultured STM cells with a low pH/low magnesium medium (MgM) under two different conditions termed MgM-Shock and MgM-Dilution and investigated the impacts of these culturing conditions on the STM proteome by using liquid chromatography-tandem mass spectrometry (LC-MS/MS)-based proteomics. LC-MS/MS results showed that alteration of culturing conditions affected a group of STM proteins differently. Compared to MgM-Shock, MgM-Dilution induced more proteins of the Salmonella-pathogenecity island 2-type III secretion system (SPI2-T3SS). The abundances of the proteins used for cobalamin biosynthesis increased under MgM-Shock condition but decreased under MgM-Dilution condition, while those proteins used for thiamine or biotin biosynthesis were not affected under the former condition but increased under the latter condition. Western-blot (WB) analysis confirmed the LC-MS/MS results. Because cobalamin, thiamine and biotin play different roles in STM metabolism, differential induction of the proteins involved in their biosyntheses suggests that the metabolic states of STM cells under these conditions differ considerably. WB analysis also showed that the abundances of SPI2-T3SS proteins SsaQ and SseE and biotin biosynthesis proteins BioB and BioD increased after STM infection of RAW 264.7 macrophages. Deletion of the gene encoding BioB reduced the ability of STM to replicate inside the macrophages, demonstrating for the first time the involvement of a biotin synthesis protein in STM colonization of macrophages.

Solid-liquid stable phase equilibria of the ternary systems MgCl2 + MgB6O10+ H2O AND MgSO4 + MgB6O10 + H2O at 308.15 K

Directory of Open Access Journals (Sweden)

Lingzong Meng

2014-03-01

Full Text Available The solubilities and the relevant physicochemical properties of the ternary systems MgCl2 + MgB6O10 + H2O and MgSO4 + MgB6O10 + H2O at 308.15 K were investigated using an isothermal dissolution method. It was found that there is one invariant point, two univariant curves, and two crystallization regions of the systems. The systems belong to a simple co-saturated type, and neither double salts nor solid solutions were found. Based on the extended HW model and its temperature-dependent equations, the single-salt Pitzer parameters β(0, β(1, β(2 and CØ for MgCl2, MgSO4, and Mg(B6O7(OH6, the mixed ion-interaction parameters θCl,B6O10, θSO4,B6O10, ΨMg,Cl,B6O10, ΨMg,SO4,B6O10 of the systems at 308.15 K were fitted, In addition, the average equilibrium constants of the stable equilibrium solids at 308.15 K were obtained by a method using the activity product constant. Then the solubilities of the ternary systems are calculated. The calculated solubilities agree well with the experimental values.

Effect of Mg, Ca, and Zn on stability of LiBH{sub 4} through computational thermodynamics

Energy Technology Data Exchange (ETDEWEB)

Lee, Sung Hoon; Manga, Venkateswara Rao; Liu, Zi-Kui [Department of Materials Science and Engineering, The Pennsylvania State University, University Park, PA 16802 (United States)

2010-07-15

The effect of divalent metal-dopants, Mg, Ca, and Zn, on the stability of LiBH{sub 4} is studied by using the first-principles calculations and CALPHAD (CALculation of PHAse Diagram) modeling. The ground states of Mg{sub 1/2}BH{sub 4}, Ca{sub 1/2}BH{sub 4}, and Zn{sub 1/2}BH{sub 4} are shown to be I anti 4m2, F2dd, and I anti 4m2, respectively, through first-principles calculations. Positive enthalpy of mixing between Li and the alloying element is predicted, indicating unfavorable solubility of alloying elements in LiBH{sub 4} and thus offering possibility to decrease the stability of LiBH{sub 4}. The ionic sublattice model of (Li{sup +}, M{sup 2+}, Va){sub 1}(BH{sub 4}{sup -}){sub 1} is adopted for the metal substituted LiBH{sub 4} phase. It is observed that the addition of Mg or Zn has limited effect as the decomposition temperature is between those of LiBH{sub 4} and M{sub 1/2}BH{sub 4} for Mg and Zn substitutions. LiBH{sub 4} is destabilized with magnesium borides or LiZn{sub 4} formation but its decomposition temperature is higher than that of M{sub 1/2}BH{sub 4}. On the other hand, the addition of Ca significantly reduces the H{sub 2} releasing temperature due to the formation of highly stable CaB{sub 6}. (author)

MgB2 Süperiletken Tellerde Alternatif Akım Kaybı ve Akı Perçinleme Mekanizmaları

OpenAIRE

SAFRAN, Serap

2010-01-01

Bu çalışmada çok filamanlı Bi-2223/Ag şerit ve farklı kılıf malzemesine sahip tek ve çok filamanlı MgB₂ teller için alternatif akım (AA) kaybı deneysel olarak ölçüldü.  Bu süperiletkenler için teorik olarak manyetik alan şerit yüzeyine dik olarak uygulandığı zaman AA kayıp hesaplanarak deneysel sonuçlarla karşılaştırıldı. Deneysel verilerle hesaplamalar arasında iyi bir uyum gözlendi. Hesaplamalar için ticari sonlu elemanlar yazılımı (Comsol Multiphysi...

Multilevel processor-sharing algorithm for M/G/1 systems with priorities

Energy Technology Data Exchange (ETDEWEB)

Yassouridis, A.; Koller, R.

1983-01-01

The well-known multilevel processor-sharing algorithm for M/G/1 systems without priorities is extended to M/G/1 systems with priority classes. The average response time t/sub j/(x) and the average waiting time w/sub j/(x) for a j-class job, which requires a total service of x sec, are analytically calculated. Some figures demonstrate how the priority classes and the total number of different levels affect the behaviour of the functions t/sub j/(x) and w/sub j/(x). In addition, the foreground-background algorithm with priorities, which is not yet covered in the literature, is treated as a special case of the multilevel processor-sharing algorithm. 8 references.

Stability of midazolam hydrochloride injection 1-mg/mL solutions in polyvinyl chloride and polyolefin bags.

Science.gov (United States)

Karlage, Kelly; Earhart, Zachary; Green-Boesen, Kelly; Myrdal, Paul B

2011-08-15

The stability of midazolam hydrochloride injection 1-mg/mL solutions in polyvinyl chloride (PVC) and polyolefin bags under varying conditions was evaluated. Triplicate solutions of midazolam hydrochloride 1-mg/mL were prepared in polyolefin and PVC i.v. bags by diluting midazolam hydrochloride injection 5 mg/mL with 5% dextrose injection. Bags were then stored under refrigeration (3-4 °C), exposed to light at room temperature (20-25 °C), or protected from light in amber bags at room temperature. Samples were taken immediately after preparation (day 0) and on days 1, 2, 3, 6, 13, 20, and 27 for analysis with a stability-indicating high-performance liquid chromatography assay in order to determine solution concentration. Stability was defined as retention of at least 90% of the initial drug concentration. The pH of each solution was also measured weekly. Sterility of the i.v. bags was determined at the end of the study by microbiological testing with culture in growth media. Differences in concentrations under the various storage conditions and bags used were analyzed using analysis of variance. All solutions retained over 98% of the initial midazolam hydrochloride concentration, with no statistically significant (p ≥ 0.05) change in concentration over the four-week period. Stability was not affected by temperature, exposure to light, or bag type. The pH of all solutions remained between 3.2 and 3.4 throughout the study. Sterility after 28 days was retained. Midazolam hydrochloride 1-mg/mL solutions diluted in 5% dextrose injection remained stable over 27 days in both polyolefin and PVC i.v. bags, regardless of storage condition.

Energetic prediction on the stability of A2Mg12Si7, A2Mg4Si3, and AMgSi in the A2Si–Mg2Si system (A = Ca, Sr and Ba) and their calculated electronic structures

International Nuclear Information System (INIS)

Imai, Yoji; Mori, Yoshihisa; Nakamura, Shigeyuki; Takarabe, Ken-ichi

2014-01-01

Highlights: • Formation energies of A 2 Mg 4 Si 3 , A 2 Mg 12 Si 7 , and AMgSi (A = Ca,Sr,Ba) were calculated. • All AMgSi are quite stable compared to mixture of A 2 Si and Mg 2 Si. • Ba 2 Mg 4 Si 3 and Sr 2 Mg 4 Si 3 are predicted to be stable, but Ca 2 Mg 4 Si 3 is not. • Ca 2 Mg 12 Si 7 and Sr 2 Mg 12 Si 7 are energetically unstable. • Stability of Ba 2 Mg 12 Si 7 is a tender subject. -- Abstract: In order to evaluate the relative stability of A 2 Mg 4 Si 3 , A 2 Mg 12 Si 7 , and AMgSi (A = Ca, Sr, and Ba) in the A 2 Si–Mg 2 Si system, electronic energy changes in the formation of these compounds were calculated using a density-functional theory with the Perdew–Wang generalized gradient approximations. It was found that (1) AMgSi’s are quite stable compared to equi-molar mixture of A 2 Si and Mg 2 Si, (2) Ba 2 Mg 4 Si 3 and Sr 2 Mg 4 Si 3 are also stable, (3) Ca 2 Mg 4 Si 3 and Ca 2 Mg 12 Si 7 are less stable than the mixture of CaMgSi and Mg 2 Si, and (4) Stability of Ba 2 Mg 12 Si 7 is a tender subject and Sr 2 Mg 12 Si 7 is energetically unstable compared to the mixture of Sr 2 Mg 4 Si 3 (or, SrMgSi) and Mg 2 Si. The presence of Sr 2 Mg 12 Si 7 may be due to the vibrational and/or configurational entropy, which are not treated in the present study. From the calculated electronic densities of state, complex compounds of SrMgSi and Mg 2 Si have both p-type and n-type character, depending on the ratio of SrMgSi and Mg 2 Si in that compound

Global and local asymptotics for the busy period of an M/G/1 queue

NARCIS (Netherlands)

Denisov, D.E.; Shneer, V.

2010-01-01

We consider an M/G/1 queue with subexponential service times. We give a simple derivation of the global and local asymptotics for the busy period. Our analysis relies on the explicit formula for the joint distribution for the number of customers and the length of the busy period of an M/G/1 queue.

Pharmacokinetic and tolerability of i.m. disodium clodronate 200 mg/lidocaine 1%, given twice monthly, in comparison with i.m. disodium clodronate 100 mg/lidocaine 1%, given weekly, in healthy postmenopausal female patients.

Science.gov (United States)

Radicioni, Milko; Cremonesi, Giovanni; Baraldi, Enrica; Leuratti, Chiara; Mariotti, Fabrizia

2013-04-01

Clodronate is a bisphosphonate effective in the prevention and treatment of osteoporosis in postmenopausal women. Non-adherence to bisphosphonates, however, is a major issue in clinical practice. Simplifying dose regimens may increase compliance. To assess bioequivalence between an intramuscular (i.m.) clodronate 200 mg/lidocaine 1% twice-a-month formulation and a clodronate 100 mg/lidocaine 1% weekly formulation in 32 postmenopausal women. In this double-blind, randomized, two-way crossover study, test and reference formulations were administered in single dose, with a 2-week wash-out between administrations. The primary endpoint was clodronic acid cumulative excretion in the first 24 hours after injection (Xu0-24h). Cumulative excretion in the 72 hours post-dose (Xu0-72h) and maximum excretion rate (Ratemax) were also evaluated. Bioequivalence was assumed if the 90% confidence intervals (CIs) of the geometric means ratios of the dose-normalized parameters were within the 80.00 - 125.00% range. Local tolerability was evaluated. Mean Xu0-24h values were 114.03 ±23.13 mg and 55.22 ±9.73 mg for clodronate 200 mg and 100 mg. The 90% CIs for dose-normalized Xu0-24h, Xu0-72h and Ratemax ere 95 -110%, 94 -107% and 95 - 113%. Local tolerability of both treatments was good. The differences in pain intensity between formulations were not sigificantly different at most assessment times. Headache was the only treatment-related adverse event. Bioequivalence of the two formulations was confirmed in terms of dose-normalized rate and amount of clodronic acid excretion. This result, together with the favorable tolerability of the novel 200 mg formulation, suggests the possibility of reducing the number of i.m. administrations from once-a-week to twice-a-month.

The magnetic Curie temperature and exchange coupling between cations in tetragonal spinel oxide Mn{sub 2.5}M{sub 0.5}O{sub 4} (M = Co, Ni, Mn, Cr, and Mg) films

Energy Technology Data Exchange (ETDEWEB)

Kuo, K.; Cheng, C. W.; Chern, G. [Physics Department and SPIN Research Center, National Chung Cheng University, Chia-Yi, Taiwan, 621 (China)

2012-04-01

Mn{sub 3}O{sub 4} is a Jahn-Taller tetragonal ferrite that has a relatively low Curie temperature (T{sub c}) of {approx}43 K due to weak coupling between the canting spins. In this study, we fabricated a series of 100-nm-thick Mn{sub 2.5}M{sub 0.5}O{sub 4} (M = Co, Ni, Mn, Cr, and Mg) films via oxygen-plasma-assisted molecular beam epitaxy and measured the structural and magnetic properties of these films. These films show single phase quality, and the c-axis lattice parameter of pure Mn{sub 3}O{sub 4} is 0.944 nm, with a c/a ratio {approx}1.16, consistent with the bulk values. The replacement of Mn by M (M = Co, Ni, Cr, and Mg) changes the lattice parameters, and the c/a ratio varies between 1.16 and 1.06 depending upon the cation distribution of the films. The magnetic Curie temperatures of these films also vary in the range of 25-66 K in that Ni and Co enhance the T{sub c} whereas Mg reduces the T{sub c} (Cr shows no effect on the T{sub c}). These changes to the T{sub c} are related to both the element electronic state and the cation distributions in these compounds. As a non-collinear spin configuration can induce electrical polarization, the present study provides a systematic way to enhance the magnetic transition temperature in tetragonal spinel ferrites.

Composition and local bonding in RE-Si-M-O-N (M=Mg, Al ; RE=La, Lu) glasses

Energy Technology Data Exchange (ETDEWEB)

Fouquet-Parry, V. [Service de Physique et de Chimie des Surfaces et des Interfaces, DSM/DRECAM/SPCSI, CEA Saclay, 91191 Gif sur Yvette Cedex (France); Paumier, F. [Laboratoire de Metallurgie Physique - UMR 6630 CNRS, Department of Materials Sciences, University of Poitiers (France); Guittet, M.J. [Service de Physique et de Chimie des Surfaces et des Interfaces, DSM/DRECAM/SPCSI, CEA Saclay, 91191 Gif sur Yvette Cedex (France); Gautier-Soyer, M. [Service de Physique et de Chimie des Surfaces et des Interfaces, DSM/DRECAM/SPCSI, CEA Saclay, 91191 Gif sur Yvette Cedex (France)], E-mail: mgautiersoyer@cea.fr; Satet, R.; Hoffmann, M.J. [Institut fuer Keramik im Maschinenbau, Universitaet Karlsruhe (Thailand), Haid-und-Neu-Strasse 7, D 76131 Karlsruhe (Germany); Becher, P.F.; Painter, G.S. [Metals and Ceramics Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States)

2008-05-30

Two series of oxynitride glasses, RE-Si-Mg-O-N (M=Mg, Al ; RE=La, Lu), have been studied by X-Ray photoelectron spectroscopy (XPS). The oxygen 1s photoelectron lineshape reveals a striking difference depending on the rare earth, both in the Mg series and in the Al series. Specifically, the oxygen 1s photoelectron lines of the La doped glasses are broader than the ones of the Lu doped glasses. This result is an experimental evidence that Lu has a larger affinity for oxygen versus nitrogen than La, as theoretically predicted by the first-principles calculations by Painter et al.

Cryogenic milling for the fabrication of high J{sub c} MgB{sub 2} bulk superconductors

Energy Technology Data Exchange (ETDEWEB)

Kim, D. N.; Kang, M. O.; Park, H. W. [Korea University of Technology and Education, Cheonan (Korea, Republic of); Jun, B. H.; Kim, C. J. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2017-06-15

Cryogenic milling which is a combined process of low-temperature treatment and mechanical milling was applied to fabricate high critical current density (J{sub c}) MgB{sub 2} bulk superconductors. Liquid nitrogen was used as a coolant, and no solvent or lubricant was used. Spherical Mg (6-12 μm, 99.9 % purity) and plate-like B powder (⁓ 1 μm, 97 % purity) were milled simultaneously for various time periods (0, 2, 4, 6 h) at a rotating speed of 500 rpm using ZrO{sub 2} balls. The (Mg{sup +2B}) powders milled were pressed into pellets and heat-treated at 700°C for 1 h in flowing argon. The use of cryomilled powders as raw materials promoted the formation reaction of superconducting MgB{sub 2}, reduced the grain size of MgB{sub 2}, and suppressed the formation of impurity MgO. The superconducting critical temperature (T{sub c}) of MgB{sub 2} was not influenced as the milling time (t) increased up to 6 h. Meanwhile, the critical current density (J{sub c}) of MgB{sub 2} increased significantly when t increased to 4 h. When t increased further to 6 h, however, Jc decreased. The J{sub c} enhancement of MgB{sub 2} by cryogenic milling is attributed to the formation of the fine grain MgB{sub 2} and a suppression of the MgO formation.

Lattice stability and formation energies of intrinsic defects in Mg2Si and Mg2Ge via first principles simulations

International Nuclear Information System (INIS)

Jund, Philippe; Viennois, Romain; Tédenac, Jean-Claude; Colinet, Catherine; Hug, Gilles; Fèvre, Mathieu

2013-01-01

We report an ab initio study of the semiconducting Mg 2 X (with X = Si, Ge) compounds and in particular we analyze the formation energies of the different point defects with the aim of understanding the intrinsic doping mechanisms. We find that the formation energy of Mg 2 Ge is 50% larger than that of Mg 2 Si, in agreement with the experimental tendency. From a study of the stability and the electronic properties of the most stable defects, taking into account the growth conditions, we show that the main cause of the n doping in these materials comes from interstitial magnesium defects. Conversely, since other defects acting like acceptors such as Mg vacancies or multivacancies are more stable in Mg 2 Ge than in Mg 2 Si, this explains why Mg 2 Ge can be of n or p type, in contrast to Mg 2 Si. The finding that the most stable defects are different in Mg 2 Si and Mg 2 Ge and depend on the growth conditions is important and must be taken into account in the search for the optimal doping to improve the thermoelectric properties of these materials.

Separation of {sup 195(m,g),197m}Hg from bulk gold target by liquid-liquid extraction using hydrophobic ionic liquids

Energy Technology Data Exchange (ETDEWEB)

Ghosh, Kaustab; Lahiri, Susanta [Saha Institute of Nuclear Physics, Kolkata (India). Chemical Sciences Div.; Maiti, Moumita [Indian Institute of Technology Roorkee, Roorkee (India). Dept. of Physics

2017-07-01

The {sup 195(m,g),197m}Hg radionuclides were produced in accelerator when natural Au foil was irradiated with 23 MeV protons. The no-carrier-added (NCA) Hg radioisotopes were separated from the bulk Au target by liquid-liquid extraction (LLX) employing hydrophobic RTILs 1-butyl-3-methylimidazolium hexafluorophosphate([C{sub 4}mim][PF{sub 6}]) and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide([bmim][Tf{sub 2}N]) as extractant with HNO{sub 3} and HCl. In each case, bulk Au was extracted into the RTIL phase leaving NCA Hg-radionuclides in the aqueous phase. The RTILs were recovered by washing with 1 M K{sub 2}S{sub 2}O{sub 5} and freshly prepared 1 M FeSO{sub 4}. The reported separation methods follow green chemistry approach as it does not involve any volatile reagents.

Photodissociation spectroscopy of the Mg+-acetic acid complex

Science.gov (United States)

Abate, Yohannes; Kleiber, P. D.

2006-11-01

We have studied the structure and photodissociation of Mg+-acetic acid clusters. Ab initio calculations suggest four relatively strongly bound ground state isomers for the [MgC2H4O2]+ complex. These isomers include the cis and trans forms of the Mg+-acetic acid association complex with Mg+ bonded to the carbonyl O atom of acetic acid, the Mg+-acetic acid association complex with Mg+ bonded to the hydroxyl O atom of acetic acid, or to a Mg+-ethenediol association complex. Photodissociation through the Mg+-based 3p←3s absorption bands in the near UV leads to direct (nonreactive) and reactive dissociation products: Mg+, MgOH+, Mg(H2O )+, CH3CO+, and MgCH3+. At low energies the dominant reactive quenching pathway is through dehydration to Mg(H2O)+, but additional reaction channels involving C-H and C-C bond activation are also open at higher energies.

Pseudobrookite-type MgTi2O5 water purification filter with controlled particle morphology

Directory of Open Access Journals (Sweden)

Yuta Nakagoshi

2015-09-01

Full Text Available Pseudobrookite-type oxide-based ceramics, such as Al2TiO5 and MgTi2O5, have recently been studied as porous ceramic membranes. Here, the effect of LiF doping on the morphology of MgTi2O5 particles is presented in detail. Water purification filters were produced using porous MgTi2O5, with different particle morphologies. MgCO3 (basic and TiO2 powders with various LiF contents were wet-ball milled, dried, and then, calcined in air at 1100 °C to obtain the MgTi2O5 powders. The powder compacts were sintered at 1000–1200 °C to produce the MgTi2O5 disk filters. The 0.5 wt.% LiF-doped MgTi2O5 disk filter, with elongated grains, showed well-balanced performance removing boehmite particles with diameter of 0.7 μm. Non-doped MgTi2O5 disk filter with equiaxed grains was suitable for precise filtration.

Co-hydrothermal synthesis of LiMn_2_3_/_2_4Mg_1_/_2_4PO_4·LiAlO_2/C nano-hybrid cathode material with enhanced electrochemical performance for lithium-ion batteries

International Nuclear Information System (INIS)

Zhang, Jun; Luo, Shaohua; Chang, Longjiao; Hao, Aimin; Wang, Zhiyuan; Liu, Yanguo; Xu, Qian; Wang, Qing; Zhang, Yahui

2017-01-01

Highlights: • A co-hydrothermal approach to synthesize LiMn_2_3_/_2_4Mg_1_/_2_4PO_4·LiAlO_2/C composite material in water/PEG system is present. • The Mn_1_-_xMg_xPO_4 precursor is prepared by precipitation reaction. • Co-modified with Mg"2"+ doping and LiAlO_2 compositing strategies play an important role in improving the electronic conductivity and facilitating the diffusion of lithium ion. • LiMn_2_3_/_2_4Mg_1_/_2_4PO_4·LiAlO_2/C composite material exhibits a high specific discharge capacity of 151.8 mAh/g at 0.05C. - Abstract: LiMn_2_3_/_2_4Mg_1_/_2_4PO_4·LiAlO_2/C is synthesized by a co-hydrothermal method in water/PEG system using Li_2CO_3, AAO and Mn_1_-_xMg_xPO_4 as raw material. The electronic structure and micromorphology of multi-component compound LiMn_1_-_xMg_xPO_4/C (x = 0, 1/24, 1/12, 1/6) and nano-hybrid LiMn_2_3_/_2_4Mg_1_/_2_4PO_4·LiAlO_2/C cathode materials are studied by first-principles calculation and experimental research including XRD, SEM, TEM. The calculated band gap of LiMn_2_3_/_2_4Mg_1_/_2_4PO_4/C is 2.296 eV, which is lower than other percentages Mg"2"+ doping samples. Electrochemical tests exhibit LiMn_2_3_/_2_4Mg_1_/_2_4PO_4/C has better cycling performance and rate capability than other contents Mg"2"+ doping samples with the discharge capacity of 143.5 mAh/g, 141.5 mAh/g, 139.2 mAh/g and 136.3 mAh/g at 0.05C, 0.1C, 0.5C and 1C in order. After compositing and preparation of LiMn_2_3_/_2_4Mg_1_/_2_4PO_4·LiAlO_2/C composite material by co-hydrothermal route, the initial discharge capacity reaches up to 151.8 mAh/g, which suggests that co-modified with Mg"2"+ doping and LiAlO_2 compositing material can improve the electronic conductivity of LiMnPO_4/C by facilitating the lithium ion diffusion rate in the interior of the materials.

Towards Horizontal Architecture for Autonomic M2M Service Networks

Directory of Open Access Journals (Sweden)

Juhani Latvakoski

2014-05-01

Full Text Available Today, increasing number of industrial application cases rely on the Machine to Machine (M2M services exposed from physical devices. Such M2M services enable interaction of physical world with the core processes of company information systems. However, there are grand challenges related to complexity and “vertical silos” limiting the M2M market scale and interoperability. It is here expected that horizontal approach for the system architecture is required for solving these challenges. Therefore, a set of architectural principles and key enablers for the horizontal architecture have been specified in this work. A selected set of key enablers called as autonomic M2M manager, M2M service capabilities, M2M messaging system, M2M gateways towards energy constrained M2M asset devices and creation of trust to enable end-to-end security for M2M applications have been developed. The developed key enablers have been evaluated separately in different scenarios dealing with smart metering, car sharing and electric bike experiments. The evaluation results shows that the provided architectural principles, and developed key enablers establish a solid ground for future research and seem to enable communication between objects and applications, which are not initially been designed to communicate together. The aim as the next step in this research is to create a combined experimental system to evaluate the system interoperability and performance in a more detailed manner.

Effects of carbon concentration and filament number on advanced internal Mg infiltration-processed MgB2 strands

International Nuclear Information System (INIS)

Li, G Z; Sumption, M D; Zwayer, J B; Susner, M A; Collings, E W; Rindfleisch, M A; Thong, C J; Tomsic, M J

2013-01-01

In this paper we show that an advanced internal Mg infiltration method (AIMI) is effective in producing superconducting wires containing dense MgB 2 layers with high critical current densities. The in-field critical current densities of a series of AIMI-fabricated MgB 2 strands were investigated in terms of C doping levels, heat treatment (HT) time and filament numbers. The highest layer J c for our monofilamentary AIMI strands was 1.5 × 10 5 A cm −2 at 10 T, 4.2 K, when the C concentration was 3 mol% and the strand was heat-treated at 675 ° C for 4 h. Transport critical currents were also measured at 4.2 K on short samples and 1 m segments of 18-filament C doped AIMI strands. The layer J c s reached 4.3 × 10 5 A cm −2 at 5 T and 7.1 × 10 4 A cm −2 at 10 T, twice as high as those of the best powder-in-tube strands. The analysis of these results indicates that the AIMI strands, possessing both high layer J c s and engineering J e s after further optimization, have strong potential for commercial applications. (paper)

A molecular dual fluorescence-ON probe for Mg2+ and Zn2+: Higher selectivity towards Mg2+ over Zn2+ in a mixture

International Nuclear Information System (INIS)

Maity, Shubhra Bikash; Bharadwaj, Parimal K.

2014-01-01

A Schiff base incorporating a coumarin fluorophore has been synthesized from easily available materials and is characterized by X-ray crystallography and other techniques. The probe serves as a dual analyte sensor and quantifies Mg 2+ and Zn 2+ ions by emission enhancement at different wavelengths without interference from a host of biologically relevant alkali/alkaline earth and transition metal ions. In presence of Mg 2+ the light yellow color of the probe in methanol changes to yellow–orange while in presence of Zn 2+ ion it changes to orange and hence can be detected through naked eye. The probe selectively gives emission of Mg 2+ when Zn 2+ ion is also present. - Highlights: • A Schiff base incorporating a coumarin fluorophore has been synthesized. • It acts as a dual analyte sensor and quantifies Mg 2+ and Zn 2+ ions by emission enhancement at different wavelengths. • It shows excellent selectivity for Mg 2+ ion in presence of alkali, alkaline earth metals as well as first row transition metals

Observation of Two-Proton Radioactivity of 19Mg by Tracking the Decay Products

International Nuclear Information System (INIS)

Mukha, I.; Alvarez, M. A. G.; Espino, J.; Gomez-Camacho, J.; Suemmerer, K.; Chatillon, A.; Geissel, H.; Hoffmann, J.; Kurz, N.; Litvinov, Yu.; Nociforo, C.; Ott, W.; Roeckl, E.; Weick, H.; Acosta, L.; Garcia-Ramos, J. E.; Martel, I.; Casarejos, E.; Cortina-Gil, D.; Rodriguez-Tajes, C.

2007-01-01

We have observed the two-proton radioactivity of the previously unknown 19 Mg ground state by tracking the decay products in-flight. For the first time, the trajectories of the 2p-decay products, 17 Ne+p+p, have been measured by using tracking microstrip detectors which allowed us to reconstruct the 2p-decay vertices and fragment correlations. The half-life of 19 Mg deduced from the measured vertex distribution is 4.0(15) ps in the system of 19 Mg. The Q value of the 2p decay of the 19 Mg ground state inferred from the measured p-p- 17 Ne correlations is 0.75(5) MeV

Contribution to the study of Li{sub x}(Co,M)O{sub 2} phases used as cathodes in Li-ion batteries. Combined effects of the lithium sur-stoichiometry and of the substitution (M = Ni, Mg); Contribution a l'etude des phases Li{sub x}(Co,M)O{sub 2} en tant que materiaux d'electrode positive des batteries Li-ion. Effets combines de la surstoechiometrie en lithium et de la substitution (M = Ni, Mg)

Energy Technology Data Exchange (ETDEWEB)

Levasseur, St.

2001-12-01

Li{sub x0}(Co,M)O{sub 2} (M = Ni, Mg; x0 {<=} 1.0) materials used as positive electrode for Li-ion batteries have been prepared at high temperature (900 degrees C) and characterized by X-ray diffraction, galvano-static measurements, {sup 7}Li MAS NMR spectroscopy and electrical properties measurements. If the results on the LiCoO{sub 2} phase agree with the literature, the adding of an excess of lithium during synthesis leads to the presence in the actual materials to the presence of oxygen vacancies and intermediate spin Co{sup 3+} ions (Co{sup 3+(IS)}) in a square-based environment. This defect suppresses all the phase transitions usually observed upon lithium de-intercalation in Li{sub x}CoO{sub 2}. The partial substitution by Ni ions allows us to separate the relative contribution of Ni(III) and Co{sup 3+(IS)} ions in the suppression of the various phase transitions upon cycling. Mg doping, even without any lithium excess, systematically induces some oxygen vacancies and Co{sup 3+(IS)} ions in the material. This observation had been correlated to the behaviour of the Li{sub x}(Co,Mg)O{sub 2} system upon cycling. (author)

Transport properties and exponential n-values of Fe/MgB2 tapes with various MgB2 particle sizes

International Nuclear Information System (INIS)

Lezza, P.; Abaecherli, V.; Clayton, N.; Senatore, C.; Uglietti, D.; Suo, H.L.; Fluekiger, R.

2004-01-01

Fe/MgB 2 tapes have been prepared starting with pre-reacted binary MgB 2 powders. As shown by resistive and inductive measurements, the reduction of particle size to a few microns by ball milling has little influence on B c2 , while the superconducting properties of the individual MgB 2 grains are essentially unchanged. Reducing the particle size causes an enhancement of B irr from 14 to 16 T, while J c has considerably increased at high fields, its slope J c (B) being reduced. At 4.2 K, values of 5.3 x 10 4 and 1.2 x 10 3 A/cm 2 were measured at 3.5 and 10 T, respectively, suggesting a dominant role of the conditions at the grain interfaces. A systematic variation of these conditions at the interfaces is undertaken in order to determine the limit of transport properties for Fe/MgB 2 tapes. The addition of 5% Mg to MgB 2 powder was found to affect neither J c nor B c2 . For the tapes with the highest J c values, very high exponential n factors were measured: n=148, 89 and 17 at 3.5, 5 and 10 T, respectively and measurements of critical current versus applied strain have been performed. The mechanism leading to high transport critical current densities of filamentary Fe/MgB 2 tapes based on MgB 2 particles is discussed

The role of MgO content in ex situ MgB₂ wires

DEFF Research Database (Denmark)

Kovac, P.; Hugek, I.; Meligek, T.

2004-01-01

An experimental study of the effect of MgO content in the MgB2 powder used for ex situ made composite wires was carried out. Two single-core MgB2/Fe/Cu wires were made using commercial MgB2 powders from Alfa Aesar containing different fraction of MgO. Critical temperature and critical currents of...

Structures and Spectroscopy Studies of Two M(II-Phosphonate Coordination Polymers Based on Alkaline Earth Metals (M = Ba, Mg

Directory of Open Access Journals (Sweden)

Kui-Rong Ma

2013-01-01

Full Text Available The two examples of alkaline-earth M(II-phosphonate coordination polymers, [Ba2(L(H2O9]·3H2O (1 and [Mg1.5(H2O9]·(L-H21.5·6H2O (2 (H4L = H2O3PCH2N(C4H8NCH2PO3H2, N,N′-piperazinebis(methylenephosphonic acid, (L-H2 = O3PH2CHN(C4H8NHCH2PO3 have been hydrothermally synthesized and characterized by elemental analysis, FT-IR, PXRD, TG-DSC, and single-crystal X-ray diffraction. Compound 1 possesses a 2D inorganic-organic alternate arrangement layer structure built from 1D inorganic chains through the piperazine bridge, in which the ligand L−4 shows two types of coordination modes reported rarely at the same time. In 1, both crystallographic distinct Ba(1 and Ba(2 ions adopt 8-coordination two caps and 9-coordination three caps triangular prism geometry structures, respectively. Compound 2 possesses a zero-dimensional mononuclear structure with two crystallographic distinct Mg(II ions. Free metal cations   [MgO6]n2+ and uncoordinated anions (L-H2n2- are joined together by static electric force. Results of photoluminescent measurement indicate three main emission bands centered at 300 nm, 378.5 nm, and 433 nm for 1 and 302 nm, 378 nm, and 434.5 nm for 2 (λex=235 nm, respectively. The high energy emissions could be derived from the intraligand π∗-n transition stations of H4L (310 nm and 382 nm, λex=235 nm, while the low energy emission (>400 nm of 1-2 may be due to the coordination effect with metal(II ions.

Development and properties of duplex MgF2/PCL coatings on biodegradable magnesium alloy for biomedical applications.

Science.gov (United States)

Makkar, Preeti; Kang, Hoe Jin; Padalhin, Andrew R; Park, Ihho; Moon, Byoung-Gi; Lee, Byong Taek

2018-01-01

The present work addresses the performance of polycaprolactone (PCL) coating on fluoride treated (MgF2) biodegradable ZK60 magnesium alloy (Mg) for biomedical application. MgF2 conversion layer was first produced by immersing Mg alloy substrate in hydrofluoric acid solution. The outer PCL coating was then prepared using dip coating technique. Morphology, elements profile, phase structure, roughness, mechanical properties, invitro corrosion, and biocompatibility of duplex MgF2/PCL coating were then characterized and compared to those of fluoride coated and uncoated Mg samples. The invivo degradation behavior and biocompatibility of duplex MgF2/PCL coating with respect to ZK60 Mg alloy were also studied using rabbit model for 2 weeks. SEM and TEM analysis showed that the duplex coating was uniform and comprised of porous PCL film (~3.3 μm) as upper layer with compact MgF2 (~2.2 μm) as inner layer. No significant change in microhardness was found on duplex coating compared with uncoated ZK60 Mg alloy. The duplex coating showed improved invitro corrosion resistance than single layered MgF2 or uncoated alloy samples. The duplex coating also resulted in better cell viability, cell adhesion, and cell proliferation compared to fluoride coated or uncoated alloy. Preliminary invivo studies indicated that duplex MgF2/PCL coating reduced the degradation rate of ZK60 Mg alloy and exhibited good biocompatibility. These results suggested that duplex MgF2/PCL coating on magnesium alloy might have great potential for orthopedic applications.

Precipitation of hydrated Mg carbonate with the aid of carbonic anhydrase for CO2 sequestration

Science.gov (United States)

Power, I. M.; Harrison, A. L.; Dipple, G. M.

2011-12-01

Strategies for sequestering CO2 directly from the atmosphere are likely required to achieve the desired reduction in CO2 concentration and avoid the most damaging effects of climate change [1]. Numerous studies have demonstrated the accelerated precipitation of calcium carbonate minerals with the aid of carbonic anhydrase (CA) as a means of sequestering CO2 in solid carbonate form; however, no study has examined precipitation of magnesium carbonate minerals using CA. Precipitation of magnesite (MgCO3) is kinetically inhibited [2]; therefore, Mg2+ must be precipitated as hydrated carbonate minerals. In laboratory experiments, the uptake of atmospheric CO2 into brine solutions (0.1 M Mg) was rate-limiting for the precipitation of dypingite [Mg5(CO3)4(OH)2-5H2O] with initial precipitation requiring 15 days [3]. It was also found that dypingite precipitation outpaced the uptake of CO2 gas into solution. CO2 uptake is limited by the hydration of CO2 to form carbonate ions [4]. Carbonic anhydrase (CA) enzymes are among the fastest known in nature and are able to catalyze the hydration of CO2, i.e., converting CO2(aq) to CO32- and HCO3- [5]. CA plays an important role in the carbon concentrating mechanism of photoautotrophic, chemoautotrophic, and heterotrophic prokaryotes and is involved in pH homeostasis, facilitated diffusion of CO2, ion transport, and the interconversion of CO2 and HCO3- [6]. Introducing CA into buffered Mg-rich solutions should allow for more rapid precipitation of hydrated magnesium carbonate minerals. Batch experiments were conducted using 125 mL flasks containing 100 mL of Millipore deionized water with 0.2 M of MgCl2-6H2O. To buffer pH, 1.0 g of pulverized brucite [Mg(OH)2] or 1.0 g of NaOH was added to the systems, which were amended with Bovine carbonic anhydrase (BCA) (Sigma-Aldrich). Solutions were stirred continuously and kept at room temperature (~22°C) with laboratory air introduced by bubbling. Temperature and pH were measured routinely

Active Protection of an MgB2 Test Coil

Science.gov (United States)

Park, Dong Keun; Hahn, Seungyong; Bascuñán, Juan; Iwasa, Yukikazu

2011-01-01

This paper presents results of a study, experimental and computational, of a detect-and-activate-the-heater protection technique applied to a magnesium diboride (MgB2) test coil operated in semi-persistent mode. The test coil with a winding ID of 25 cm and wound with ~500-m long reacted MgB2 wire was operated at 4.2 K immersed in a bath of liquid helium. In this active technique, upon the initiation of a “hot spot” of a length ~10 cm, induced by a “quench heater,” a “protection heater” (PH) of ~600-cm long planted within the test coil is activated. The normal zone created by the PH is large enough to absorb the test coil’s entire initial stored energy and still keeps the peak temperature within the winding below ~260 K. PMID:22081754

Formation of polycrystalline MgB2 synthesized by powder in sealed tube method with different initial boron phase

Science.gov (United States)

Yudanto, Sigit Dwi; Imaduddin, Agung; Kurniawan, Budhy; Manaf, Azwar

2018-04-01

Magnesium diboride, MgB2 is a new high critical temperature superconductor that discovered in the beginning of the 21st century. The MgB2 has a simple crystal structure and a high critical temperature, which can be manufactured in several forms like thin films, tapes, wires including bulk in the large scale. For that reason, the MgB2 has good prospects for various applications in the field of electronic devices. In the current work, we have explored the synthesis of MgB2 polycrystalline using powder in a sealed tube method. Different initial boron phase for the synthesized of MgB2 polycrystalline were used. These were, in addition to magnesium powders, crystalline boron, amorphous boron and combination both of them were respectively fitted in the synthesis. The raw materials were mixed in a stoichiometric ratio of Mg: B=1:2, ground using agate mortar, packed into stainless steel SS304. The pack was then sintered at temperature of 800°C for 2 hours in air atmosphere. Phase formation of MgB2 polycrystalline in difference of initial boron phase was characterized using XRD and SEM. Referring to the diffraction pattern and microstructure observation, MgB2 polycrystalline was formed, and the formation was effective when using the crystalline Mg and fully amorphous B as the raw materials. The critical temperature of the specimen was evaluated by the cryogenic magnet. The transition temperature of the MgB2 specimen synthesized using crystalline magnesium and full amorphous boron is 42.678 K (ΔTc = 0.877 K).

Phonon dispersion models for MgB{sub 2} with application of pressure

Energy Technology Data Exchange (ETDEWEB)

Alarco, Jose A., E-mail: jose.alarco@qut.edu.au; Talbot, Peter C., E-mail: p.talbot@qut.edu.au; Mackinnon, Ian D.R., E-mail: ian.mackinnon@qut.edu.au

2017-05-15

Highlights: • Ab initio DFT MgB{sub 2} phonon dispersion for pressures up to 20 GPa are presented. • Extent of E{sub 2g} phonon anomaly and thermal energy, T{sub δ,} are pressure dependent. • Phonon anomaly thermal energy equivalent to experimental T{sub c} values for MgB{sub 2}. • Computational method to measure T{sub δ} is an effective predictor of T{sub c}. - Abstract: We evaluate, via the Local Density and the Generalised Gradient Approximations to the Density Functional Theory (DFT), the change in form and extent of the E{sub 2g} phonon anomaly of MgB{sub 2} with increase in applied pressure up to 20 GPa. Ab initio DFT calculations on the phonon dispersion (PD) for MgB{sub 2} show a phonon anomaly symmetrically displaced around Γ, the reciprocal lattice origin. This anomaly is related to nesting between diametrically opposite sides of tubular elements of Fermi surfaces, which correspond to sigma bonding and run approximately parallel to the Γ–A reciprocal space direction. The anomaly is parallel to Γ–A and along Γ–M and Γ–K. The extent of the E{sub 2g} phonon anomaly, δ, along Γ–M and Γ–K is a measure of the thermal energy, T{sub δ}, that matches within error the experimental onset superconducting transition temperature, T{sub c}. Ab initio DFT calculations with pressure for −5 GPa < P < 20 GPa show a linear reduction in T{sub δ} that closely matches experimental T{sub c} values for MgB{sub 2}. For phonon-mediated superconductors with AlB{sub 2}–type structures, the thermal energy of the phonon anomaly, T{sub δ}, is a reliable predictor of T{sub c}.

Radiation-induced defect production in MgF2-Co crystals

International Nuclear Information System (INIS)

Nuritdinov, I.; Turdanov, K.; Mirinoyatova, N.M.; Rejterov, V.M.

1996-01-01

Impact of Co-admixture on structural radiation defects formation in the MgF 2 crystals is studied. It is found that the Co admixture facilitates the probability of generating the F- and m-type centers of radiation defects as well as creation of the F- and M-centers, perturbed by admixtures. The availability of structural defects leads in its turn to the admixture ions perturbation. It is reflected in the removal of prohibition on spin-prohibited transitions of the Co 2 + ions. It is assumed that creation of the M-centers is the main cause for removal of the prohibition on the spin-prohibited transitions. 8 refs., 4 figs

Mercury pollution in the ground of Saint-Petersburg

Energy Technology Data Exchange (ETDEWEB)

Malov, A.M. [FSSI Inst. of Toxicology FMBA of Russia, Saint-Petersburg (Russian Federation)

2008-07-01

The problem of mercury poisoning in St-Petersburg's industrial centre was investigated. First, mercury content was directly measured in ground samples taken at various depths. Mushrooms, which are abundant in every district of the city, were then collected from lawns, yards and parks. Mushrooms provide an accurate indication of mercury distribution in the upper layer of the ground because they get their nutrients from the environment. As such, the chemical composition of mushrooms depends on the composition of the substrate on which they grow, notably the composition of the ground soil and its mercury content. The purpose of the study was to determine the mercury content of the mushrooms growing in the centre of St-Petersburg and its suburbs. The mercury content of the samples was measured by using the cold vapor atomic absorption spectrometry method. The mercury content of the mushrooms collected ranged from 1.29 mg/kg to 0.010 mg/kg. There was some correlation of the 2 data sets for territorial mercury impurity. The mercury content in the blood of 2 comparable groups of women living in the central part of St-Petersburg and its suburbs was also compared. Although there was no one single patterns of mercury distribution in the ground of the city, the depth of 1.0 to 2.0 m was found to be the most polluted. It was concluded that both measuring methods could be used to determine mercury contamination, but each reflects the situation from a different perspective. 20 refs., 3 tabs.

Catalytic activity of Co-Mg-Al, Cu-Mg-Al and Cu-Co-Mg-Al mixed oxides derived from hydrotalcites in SCR of NO with ammonia

Energy Technology Data Exchange (ETDEWEB)

Chmielarz, Lucjan; Kustrowski, Piotr; Rafalska-Lasocha, Alicja [Faculty of Chemistry, Jagiellonian University, Ingardena 3, 30-060 Krakow (Poland); Majda, Dorota; Dziembaj, Roman [Regional Laboratory for Physicochemical Analyses and Structural Research, Ingardena 3, 30-060 Krakow (Poland)

2002-01-10

M-Mg-Al hydrotalcites (where M=Cu{sup 2+}, Co{sup 2+} and Cu{sup 2+}+Co{sup 2+}) with M ranging from 5 to 20% (as atomic ratio) were prepared by co-precipitation method. Obtained samples were characterised by XRD and TGA techniques. The influence of transition metal content on thermal decomposition of hydrotalcites was observed. Calcination of the hydrotalcites at 600C resulted in the formation of mixed oxides with surface areas in the range 71-154m{sup 2}/g. Calcined hydrotalcites were tested as catalysts in the selective reduction of NO with ammonia (NO-SCR). The catalytic activity depends on the kind of transition metal, as well as its content. For the NO-SCR the following reactivity order was found: Cu-Mg-Al>Cu-Co-Mg-Al>Co-Mg-Al. Temperature-programmed methods (TPD, TPSR, stop flow-TPD), as well as FT-IR spectroscopy have been applied to determine interaction of NO and NH{sub 3} molecules with the catalyst surface.

Localization of Mg2+-sensing shark kidney calcium receptor SKCaR in kidney of spiny dogfish, Squalus acanthias.

Science.gov (United States)

Hentschel, Hartmut; Nearing, Jacqueline; Harris, H William; Betka, Marlies; Baum, Michelle; Hebert, Steven C; Elger, Marlies

2003-09-01

We recently cloned a homologue of the bovine parathyroid calcium receptor from the kidney of a spiny dogfish (Squalus acanthias) and termed this new protein SKCaR. SKCaR senses alterations in extracellular Mg2+ after its expression in human embryonic kidney cells (Nearing J, Betka M, Quinn S, Hentschel H, Elger M, Baum M, Bai M, Chattopadyhay N, Brown E, Hebert S, and Harris HW. Proc Natl Acad. Sci USA 99: 9231-9236, 2002). In this report, we used light and electron microscopic immunocytochemical techniques to study the distribution of SKCaR in dogfish kidney. SKCaR antiserum bound to the apical membranes of shark kidney epithelial cells in the following tubular segments: proximal tubules (PIa and PIIb), late distal tubule, and collecting tubule/collecting duct as well as diffusely labeled cells of early distal tubule. The highly specific distribution of SKCaR in mesial tissue as well as lateral countercurrent bundles of dogfish kidney is compatible with a role for SKCaR to sense local tubular Mg2+ concentrations. This highly specific distribution of SKCaR protein in dogfish kidney could possibly work in concert with the powerful Mg2+ secretory system present in the PIIa segment of elasmobranch fish kidney to affect recycling of Mg2+ from putative Mg2+-sensing/Mg2+-reabsorbing segments. These data provide support for the possible existence of Mg2+ cycling in elasmobranch kidney in a manner analogous to that described for mammals.

Perbandingan antara Tramadol 2 mg/kgBB dan Fentanil 2 mg/kgBB Intravena Sebagai Analgetik Intraoperatif pada Operasi Laparotomi Ginekologis; Pengaruhnya terhadap Skor PRST

Directory of Open Access Journals (Sweden)

Arief Kurniawan

2017-12-01

Full Text Available Perkembangan dan kemajuan teknologi serta ilmu pengetahuan telah mendorong pelaksanaan pelayanan kesehatan yang lebih efektif dan lebih ekonomis dibanding dengan cara yang lazim dikerjakan. Telah dilakukan penelitian terhadap 32 pasien operasi laparotomi ginekologis yang dibagi menjadi dua kelompok. Kelompok Tramadol (n=16 diberikan tramadol 2 mg/kgBB (pengenceran akuabides sampai 10 mL lewat jalur infus selama satu menit, sedangkan pada kelompok Fentanil (n=16 diberikan fentanil 2 µg/kgBB dengan cara yang sama. Lima menit kemudian diberikan propofol 2 mg/kgBB, atrakurium 0,5 mg/kgBB, enfluran 2 volume %, N2O:O2=2 L/menit:2 L/menit. Setelah tiga menit dilakukan laringoskopi intubasi. Pasien diventilasi kendali dengan mode ventilator IPPV. Operasi dilaksanakan bila kedalaman anestesi tercapai berdasar atas skor PRST (P=systolic arterial pressure, R=heart rate, S=sweat, dan T=tears 2 sampai dengan 4. Analgetik pertolongan 50 µg fentanil diberikan bila skor PRST lebih dari 4. Analgetik postoperatif 30 mg ketorolak dan antimuntah 10 mg metoklopramid diberikan saat jahit kulit. Pencatatan tekanan darah, laju nadi, saturasi O2, dan skor PRST dilakukan sebagai berikut: T0 = penderita tiba di kamar operasi, T1= preintubasi, T2= satu menit setelah intubasi, T3= satu menit setelah insisi, T4 dan seterusnya diukur tiap 15 menit sampai selesai operasi. Pasien diekstubasi setelah pernapasan adekuat. Skala sedasi dan muntah dinilai setiap 15 menit setelah ekstubasi selama dua jam. Dari hasil penelitian didapatkan skor PRST mulai T1 sampai T12 secara statistis tidak berbeda bermakna antara kelompok tramadol dan fentanil (p>0,05. Kedua kelompok mengalami peningkatan skor PRST satu menit setelah intubasi. Skor PRST dipertahankan antara 0 sampai 2. Pada kelompok tramadol dan fentanil masing-masing satu orang mendapatkan analgetik pertolongan fentanil 50 µg karena skor PRST 5. Tidak ditemukan perbedaan skala sedasi dan muntah antara dua kelompok perlakuan

Hydrodechlorination of Tetrachloromethane over Palladium Catalysts Supported on Mixed MgF2-MgO Carriers

Directory of Open Access Journals (Sweden)

Magdalena Bonarowska

2016-11-01

Full Text Available Pd/MgO, Pd/MgF2 and Pd/MgO-MgF2 catalysts were investigated in the reaction of CCl4 hydrodechlorination. All the catalysts deactivated in time on stream, but the degree of deactivation varied from catalyst to catalyst. The MgF2-supported palladium with relatively large metal particles appeared the best catalyst, characterized by good activity and selectivity to C2-C5 hydrocarbons. Investigation of post-reaction catalyst samples allowed to find several details associated with the working state of hydrodechlorination catalysts. The role of support acidity was quite complex. On the one hand, a definite, although not very high Lewis acidity of MgF2 is beneficial for shaping high activity of palladium catalysts. The MgO-MgF2 support characterized by stronger Lewis acidity than MgF2 contributes to very good catalytic activity for a relatively long reaction period (~5 h but subsequent neutralization of stronger acid centers (by coking eliminates them from the catalyst. On the other hand, the role of acidity evolution, which takes place when basic supports (like MgO are chlorided during HdCl reactions, is difficult to assess because different events associated with distribution of chlorided support species, leading to partial or even full blocking of the surface of palladium, which plays the role of active component in HdCl reactions.

Hydrogen storage properties of LaMgNi3.6M0.4 (M = Ni, Co, Mn, Cu, Al) alloys

International Nuclear Information System (INIS)

Yang, Tai; Zhai, Tingting; Yuan, Zeming; Bu, Wengang; Xu, Sheng; Zhang, Yanghuan

2014-01-01

Highlights: • La–Mg–Ni system AB 2 -type alloys were prepared by induction melting. • Structures and lattice parameters were analysed by XRD. • Hydrogen absorption/desorption performances were studied. • Mechanisms of hydrogen absorption capacity fading were investigated. - Abstract: LaMgNi 3.6 M 0.4 (M = Ni, Co, Mn, Cu, Al) alloys were prepared through induction melting process. The phase compositions and crystal structures were characterised via X-ray diffraction (XRD). The hydrogen storage properties, including activation performance, hydrogen absorption capacity, cycle stability, alloy particle pulverisation and plateau pressure, were systemically investigated. Results show that Ni, Co, Mn and Cu substitution alloys exhibit multiphase structures comprising the main phase LaMgNi 4 and the secondary phase LaNi 5 . However, the secondary phase of the Al substitution alloy changes into LaAlNi 4 . The lattice parameters and cell volumes of the LaMgNi 4 phase follow the order Ni < Co < Al < Cu < Mn. Activation is simplified through partial substitution of Ni with Al, Cu and Co. The hydrogen absorption capacities of all of the alloys are approximately 1.7 wt.% at the first activation process; however, they rapidly decrease with increasing cycle number. In addition, the stabilities of hydriding and dehydriding cycles decrease in the order Al > Co > Ni > Cu > Mn. Hydriding processes result in numerous cracks and amorphisation of the LaMgNi 4 phase in the alloys. The p–c isotherms were determined by a Sieverts-type apparatus. Two plateaus were observed for the Ni, Co and Al substitution alloys, whereas only one plateau was found for Mn and Cu. This result was caused by the amorphisation of the LaMgNi 4 phase during the hydriding cycles. Reversible absorption and desorption of hydrogen are difficult to achieve. Substitutions of Ni with Co, Mn, Cu and Al significantly influence the reduction of hysteresis between hydriding and dehydriding

Corrosion behaviour of groundnut shell ash and silicon carbide hybrid reinforced Al-Mg-Si alloy matrix composites in 3.5% NaCl and 0.3M H2SO4 solutions

Directory of Open Access Journals (Sweden)

Kenneth Kanayo ALANEME

2015-05-01

Full Text Available The corrosion behaviour of Al-Mg-Si alloy based composites reinforced with groundnut shell ash (GSA and silicon carbide (SiC was investigated. The aim is to assess the corrosion properties of Al-Mg-Si alloy based hybrid reinforced composites developed using different mix ratios of GSA (a cheaply processed agro waste derivative which served as partial replacement for SiC and SiC as reinforcing materials. GSA and SiC mixed in weight ratios 0:1, 1:3, 1:1, 3:1, and 1:0 were utilized to prepare 6 and 10 wt% of the reinforcing phase with Al‐Mg‐Si alloy as matrix using two‐step stir casting method. Mass loss and corrosion rate measurement was used to study the corrosion behaviour of the produced composites in 3.5% NaCl and 0.3M H2SO4 solutions. The results show that the Al-Mg-Si alloy based composites containing 6 and 10 wt% GSA and SiC in varied weight ratios were resistant to corrosion in 3.5% NaCl solution. The composites were however more susceptible to corrosion in 0.3M H2SO4 solution (in comparison with the 3.5% NaCl solution. It was noted that the Al-Mg-Si/6 wt% GSA-SiC hybrid composite grades containing GSA and SiC in weight ratio 1:3 and 3:1 respectively exhibited superior corrosion resistance in the 0.3M H2SO4 solution compared to other composites produced for this series. In the case of the Al-Mg-Si/10 wt% GSA-SiC hybrid composite grades, the corrosion resistance was relatively superior for the composites containing a greater weight ratio of GSA (75% and 100% in 0.3M H2SO4 solution.

Grounded theory, a kvalitatív kutatás klasszikus mérföldköve (Grounded theory, the classic milestone of qualitative research)

OpenAIRE

Mitev, Ariel Zoltán

2012-01-01

A grounded theory olyan kutatási módszer, ahol az elmélet az empirikus adatokból fejlődik ki és abban gyökerezik (Glaser - Strauss, 1967). Annak ellenére, hogy a módszer nemzetközileg rendkívül népszerű, a grounded theory nem igazán vert gyökeret a hazai menedzsment- és marketingkutatás talajában. A cikk célja a grounded theory kulcsfontosságú mozzanatainak bemutatása és a módszer népszerűsítése. / === / Grounded theory is a research method in which theory emerges from the data and is grounde...

Ex-situ manufacturing of SiC-doped MgB2 used for superconducting wire in medical device applications

Science.gov (United States)

Herbirowo, Satrio; Imaduddin, Agung; Sofyan, Nofrijon; Yuwono, Akhmad Herman

2017-02-01

Magnesium diboride (MgB2) is a superconductor material with a relatively high critical temperature. Due to its relatively high critical temperature, this material is promising and has the potential to replace Nb3Sn for wire superconducting used in many medical devices. In this work, nanoparticle SiC-doped MgB2 superconducting material has been fabricated through an ex-situ method. The doping of nanoparticle SiC by 10 and 15 wt% was conducted to analyze its effect on specific resistivity of MgB2. The experiment was started by weighing a stoichiometric amount of MgB2 and nanoparticles SiC. Both materials were mixed and grounded for 30 minutes by using an agate mortar. The specimens were then pressed into a 6 mm diameter stainless steel tube, which was then reduced until 3 mm through a wire drawing method. X-ray diffraction analysis was conducted to confirm the phase, whereas the superconductivity of the specimens was analyzed by using resistivity measurement under cryogenic magnetic system. The results indicated that the commercial MgB2 showed a critical temperature of 37.5 K whereas the SiC doped MgB2 has critical temperature of 38.3 K.

Discharge behaviour of Mg-Al-Pb and Mg-Al-Pb-In alloys as anodes for Mg-air battery

International Nuclear Information System (INIS)

Wang, Naiguang; Wang, Richu; Peng, Chaoqun; Peng, Bing; Feng, Yan; Hu, Chengwang

2014-01-01

Highlights: • We investigate the effect of indium on the discharge behaviour of Mg-Al-Pb alloy. • We evaluate the performance of Mg-air batteries with Mg-Al-Pb and Mg-Al-Pb-In anodes. • We analyze the activation mechanism of Mg-Al-Pb-In alloy in the discharge process. - Abstract: The discharge behaviour of Mg-Al-Pb and Mg-Al-Pb-In alloys in 3.5 wt.% NaCl solution is investigated by electrochemical techniques, and compared with that of pure magnesium. The results show that Mg-Al-Pb-In alloy provides a more negative potential and exhibits a higher utilization efficiency in contrast with Mg-Al-Pb alloy and pure magnesium during the half-cell test at a large current density, and gives desirable discharge performance when used as anode for Mg- air battery. The peak power density of the Mg-air battery with Mg-Al-Pb-In anode is 94.5 mW cm −2 , which is comparable with those of Mg-H 2 O 2 semi-fuel batteries. Moreover, the activation mechanism of Mg-Al-Pb-In alloy during the discharge process is also analyzed

Effect of Mg substitution on crystal structure and hydrogenation of Ce{sub 2}Ni{sub 7}-type Pr{sub 2}Ni{sub 7}

Energy Technology Data Exchange (ETDEWEB)

Iwase, Kenji, E-mail: fbiwase@mx.ibaraki.ac.jp [Department of Materials Science and Engineering, Ibaraki University, 4-12-1 Nakanarusawa, Hitachi 316-8511 (Japan); Mori, Kazuhiro [Research Reactor Institute, Kyoto University, 2-1010 Asashiro-nishi, Kumatori, Sennan, Osaka 590-0494 (Japan); Terashita, Naoyoshi [Japan Metals & Chemicals Co., Ltd., Nishiokitama-gun, Yamagata 999-1351 (Japan); Tashiro, Suguru; Suzuki, Tetsuya [Department of Materials Science and Engineering, Ibaraki University, 4-12-1 Nakanarusawa, Hitachi 316-8511 (Japan)

2017-03-15

The effect of Pr being substituted by Mg in Pr{sub 2}Ni{sub 7} with a Ce{sub 2}Ni{sub 7}-type structure was investigated by X-ray diffraction (XRD) and pressure−composition (P−C) isotherm measurements. The maximum hydrogen capacity of Pr{sub 2}Ni{sub 7} reached 1.24 H/M in the first absorption process. However, 0.61 H/M hydrogen remained in the sample after the first desorption and the reversible hydrogen capacity decreased to 0.63 H/M. Severe peak broadening was observed in the XRD profile of Pr{sub 2}Ni{sub 7}H{sub 5.4} after the first P−C isotherm cycle. The metal sublattice of Pr{sub 2}Ni{sub 7}H{sub 5.4} is deformed and changes from the Ce{sub 2}Ni{sub 7}-type structure to a lower symmetry during hydrogenation, with no detection of an amorphous phase. Pr{sub 1.5}Mg{sub 0.5}Ni{sub 7} consists of two phases: 80% Gd{sub 2}Co{sub 7}-type and 20% PuNi{sub 3}-type phases. Mg substitution leads to the relative stability of the Gd{sub 2}Co{sub 7}-type and PuNi{sub 3}-type structures. The Gd{sub 2}Co{sub 7}-type and PuNi{sub 3}-type structures are retained after the P-C isotherm. The reversible hydrogen capacity reached 1.05 H/M. The structural change during the hydrogen absorption−desorption cycle and the hydrogenation characteristics are changed by Mg atoms replacing Pr in the MgZn{sub 2}-type cell. - Graphical abstract: The maximum hydrogen capacity is 1.2 H/M in the first absorption process and the reversible capacity is 0.63 H/M.

Structural and physical properties of Mg3-xZnxSb2 (x=0-1.34)

International Nuclear Information System (INIS)

Ahmadpour, Faraz; Kolodiazhnyi, Taras; Mozharivskyj, Yurij

2007-01-01

The Mg 3-x Zn x Sb 2 phases with x=0-1.34 were prepared by direct reactions of the elements in tantalum tubes. According to the X-ray single crystal and powder diffraction, the Mg 3-x Zn x Sb 2 phases crystallize in the same P3-bar m1 space group as the parent Mg 3 Sb 2 phase. The Mg 3-x Zn x Sb 2 structure is different from the other substituted structures of Mg 3 Sb 2 , such as (Ca, Sr, Ba) Mg 2 Sb 2 or Mg 5.23 Sm 0.77 Sb 4 , in a way that in Mg 3-x Zn x Sb 2 the Mg atoms on the tetrahedral sites are replaced, while in the other structures Mg on the octahedral sites is replaced. Thermoelectric performance for the two members of the series, Mg 3 Sb 2 and Mg 2.36 Zn 0.64 Sb 2 , was evaluated from low to room temperatures through resistivity, Seebeck coefficient and thermal conductivity measurements. In contrast to Mg 3 Sb 2 which is a semiconductor, Mg 2.36 Zn 0.64 Sb 2 is metallic and exhibits an 18-times larger dimensionless figure-of-merit, ZT, at room temperature. However, thermoelectric performance of Mg 2.36 Zn 0.64 Sb 2 is still poor and it is mostly due to its large electrical resistivity. - Graphical abstract: The Mg atoms in Mg 3 Sb 2 were successfully substituted with Zn, with Zn going exclusively into the tetrahedral sites. Zn substitution increases the electrical conductivity in Mg 2.36 Zn 0.64 Sb 2 by closing the band gap. This change combined with a decrease in the thermal conductivity improves the ZT value

Ground rubber: Sorption media for ground water containing benzene and O-xylene

International Nuclear Information System (INIS)

Kershaw, D.S.; Pamukcu, S.

1997-01-01

The purpose of the current study is to examine the ability of ground rubber to sorb benzene and O-xylene from water contained with aromatic hydrocarbons. The study consisted of running both batch and packed bed column tests to determine the sorption capacity, the required sorption equilibration time, and the flow through utilization efficiency of ground rubber under various contact times when exposed to water contaminated with various amounts of benzene or O-xylene. Initial batch test results indicate that ground rubber can attain equilibrium sorption capacities up to 1.3 or 8.2 mg of benzene or O-xylene, respectively, per gram of tire rubber at solution equilibrium concentrations of 10 mg/L. Packed bed column tests indicate that ground tire rubber has on the average a 40% utilization rate when a hydraulic residence time of 15 min is used. Possible future uses of round rubber as a sorption media could include, but are not limited to, the use of ground rubber as an aggregate in slurry cutoff walls that are in contact with petroleum products. Ground rubber could also be used as a sorption media in pump-and-treat methodologies or as a sorption media in in-situ reactive permeable barriers

Stabilization of MgCr₂O₄ spinel in slags of the
SiO₂-CaO-MgO-Cr₂O₃ system

Directory of Open Access Journals (Sweden)

Arredondo-Torres, V.

2006-12-01

Full Text Available El objetivo de este estudio es analizar el efecto del contenido de MgO y la basicidad de la escoria sobre la estabilidad de las especies mineralógicas del sistema de escoria SiO₂-CaOMgO-
Cr₂O₃. Se realizaron ensayos al equilibrio a 1600 °C bajo condiciones reductoras (pO2=10^-9atm. El contenido de MgO fue de 0 a 12 % masa, el Cr₂O₃ de 10% y la basicidad de 1 y 1,5. También se realizó un análisis termodinámico para determinar las fases mineralógicas más estables en la escoria. Los resultados experimentales y calculados muestran que el Cr₂O₃ se encuentra principalmente ligado en una fase espinela MgCr₂O₄, incluso a bajos contenidos de MgO. Los resultados obtenidos por microscopia electrónica de barrido (MEB-EDS, muestran la evidencia de tres estructuras cristalinas: (A Octaedros, los cuales
corresponden a la espinela MgCr₂O₄, (B Cristales alargados que corresponden a la formación de silicatos cálcicos y (C Matriz de silicatos cálcicos con impurezas de Mg y Cr que no cristalizaron por completo.

El objetivo de este estudio es analizar el efecto del contenido de MgO y la basicidad de la escoria sobre la estabilidad de las especies mineralógicas del sistema de escoria SiO₂-CaOMgO-Cr₂O₃. Se realizaron ensayos al equilibrio a 1600 °C bajo condiciones reductoras (pO₂=10^-9atm. El contenido de MgO fue de 0 a 12 % masa, el Cr₂O₃ de 10% y la basicidad de 1 y 1,5. También se realizó un análisis termodinámico para determinar las fases mineralógicas más estables en la escoria. Los resultados experimentales y calculados muestran que el Cr₂O₃ se encuentra principalmente ligado en una fase espinela MgCr₂O₄, incluso a bajos contenidos de MgO. Los resultados obtenidos por

Cr diffusion in MgAl2O4 synthetic spinels: preliminary results

Science.gov (United States)

Freda, C.; Celata, B.; Andreozzi, G.; Perinelli, C.; Misiti, V.

2012-04-01

Chromian spinel is an accessory phase common in crustal and mantle rocks, including peridotites, gabbros and basalts. Spinel, it has been identified as one of the most effective, sensible, and versatile petrogenetic indicator in mafic and ultramafic rock systems due to the strict interdependence between its physico-chemical properties (chemical composition, cation configuration etc.) and genetic conditions (temperature, pressure, and chemical characteristics of the system). In particular, studies on intra- and inter-crystalline Mg-Fe2+, Cr-Al exchange demonstrated the close relationship between spinel composition and both degree of partial melting and equilibrium temperature of spinel-peridotites. Moreover, studies focused on the chemical zoning of Mg-Fe2+ and/or Cr-Al components in spinel have been used, combined with a diffusion model, to provide quantitative information on peridotites and gabbros pressure-temperature paths and on deformation mechanisms. Although these potentials, most of the experimental studies have been performed on spinels hosting a limited content of divalent iron (sensu stricto, MgAl2O4), whereas the scarce studies on Cr-Al inter-diffusion coefficient have been performed at 3-7 GPa as pressure boundary condition. In order to contribute to the understanding of processes occurring in the lithospheric mantle, we have initiated an experimental research project aiming at determining the Cr-Al inter-diffusion in spinel at 2 GPa pressure and temperature ranging from 1100 to 1250 °C. The experiments were performed in a end-loaded piston cylinder by using a 19 mm assembly and graphite-Pt double capsules. As starting materials we used synthetic Mg-Al spinel (200-300 μm in size) and Cr2O3 powder. Microanalyses of experimental charge were performed on polished carbon-coated mounts by electronic microprobe. Line elemental analyses were made perpendicular to the contact surface between Cr2O3 powder and spinel, at interval of 2 μm. By processing these

FEBEX bentonite colloid stability in ground water

Energy Technology Data Exchange (ETDEWEB)

Seher, H.; Schaefer, T.; Geckeis, H. [Inst. fuer Nukleare Entsorgung (INE), Forschungszentrum Karlsruhe, 76021 Karlsruhe (Germany)]. e-mail: holger.seher@ine.fzk .de; Fanghaenel, T. [Ruprecht-Karls-Univ. Heidelberg, Physikalisch-Chemisches In st., D-69120 Heidelberg (Germany)

2007-06-15

Coagulation experiments are accomplished to identify the geochemical conditions for the stability of Febex bentonite colloids in granite ground water. The experiments are carried out by varying pH, ionic strength and type of electrolyte. The dynamic light scattering technique (photon correlation spectroscopy) is used to measure the size evolution of the colloids with time. Agglomeration rates are higher in MgCl{sub 2} and CaCl{sub 2} than in NaCl solution. Relative agglomeration rates follow approximately the Schulze-Hardy rule. Increasing agglomeration rates at pH>8 are observed in experiments with MgCl{sub 2} and CaCl{sub 2} which are, however, caused by coprecipitation phenomena. Bentonite colloid stability fields derived from the colloid agglomeration experiments predict low colloid stabilization in granite ground water taken from Aespoe, Sweden, and relatively high colloid stability in Grimsel ground water (Switzerland)

Nonparametric estimation of the stationary M/G/1 workload distribution function

DEFF Research Database (Denmark)

Hansen, Martin Bøgsted

2005-01-01

In this paper it is demonstrated how a nonparametric estimator of the stationary workload distribution function of the M/G/1-queue can be obtained by systematic sampling the workload process. Weak convergence results and bootstrap methods for empirical distribution functions for stationary associ...

Validación de un método analítico alternativo para la cuantificación de hidralazina en un inyectable de 20 mg/mL

Directory of Open Access Journals (Sweden)

Lisette Martínez Miranda

2004-04-01

Full Text Available Se desarrolló un método analítico por espectrofotometría ultravioleta para la cuantificación de hidralazina en un inyectable de 20 mg/mL. En la validación se evaluaron los parámetros de especificidad para estos fines, linealidad del sistema, exactitud y precisión expresada en sus 2 formas, repetibilidad y reproducibilidad. El método analítico resultó ser sencillo y rápido, además de específico, lineal, preciso, exacto en el rango de concentraciones estudiadas.An analytical method was developed by ultraviolet spectrophotometry to quantify hydralazine in an injection of 20 mg/mL. In the validation, the parameters of specificity to these ends, lineality of the system, accuracy and precision expressed in its 2 forms, repeatablity and reproducibility, were evaluated. The analytical method proved to be simple, fast, linear, accurate and exact in the range of the studied concentrations.

Comparison of the reaction of bone-derived cells to enhanced MgCl2-salt concentrations.

Science.gov (United States)

Burmester, Anna; Luthringer, Bérengère; Willumeit, Regine; Feyerabend, Frank

2014-01-01

Magnesium-based implants exhibit various advantages such as biodegradability and potential for enhanced in vivo bone formation. However, the cellular mechanisms behind this possible osteoconductivity remain unclear. To determine whether high local magnesium concentrations can be osteoconductive and exclude other environmental factors that occur during the degradation of magnesium implants, magnesium salt (MgCl2) was used as a model system. Because cell lines are preferred targets in studies of non-degradable implant materials, we performed a comparative study of 3 osteosarcoma-derived cell lines (MG63, SaoS2 and U2OS) with primary human osteoblasts. The correlation among cell count, viability, cell size and several MgCl2 concentrations was used to examine the influence of magnesium on proliferation in vitro. Moreover, bone metabolism alterations during proliferation were investigated by analyzing the expression of genes involved in osteogenesis. It was observed that for all cell types, the cell count decreases at concentrations above 10 mM MgCl2. However, detailed analysis showed that MgCl2 has a relevant but very diverse influence on proliferation and bone metabolism, depending on the cell type. Only for primary cells was a clear stimulating effect observed. Therefore, reliable results demonstrating the osteoconductivity of magnesium implants can only be achieved with primary osteoblasts.

THE THERMODYNAMIC PROPERTIES OF MELTS OF DOUBLE SYSTEM MgO – Al2O3, MgO – SiO2, MgO – CaF2, Al2O3 – SiO2, Al2O3 – CaF2, SiO2 – CaF2

Directory of Open Access Journals (Sweden)

В. Судавцова

2012-04-01

Full Text Available Methodology of prognostication of thermodynamics properties of melts is presented from the coordinatesof liquidus of diagram of the state in area of equilibria a hard component is solution, on which energies ofmixing of Gibbs are expected in the double border systems of MgO – Al2O3, MgO – SiO2, MgO – CaF2,Al2O3 – SiO2, Al2O3 - CaF2, SiO2 - CaF2. For the areas of equilibrium there is quasibinary connection(MgAl2O4, Mg2SiO4, Al6Si2O13 – a grout at calculations was used equalization of Hauffe-Wagner. Theobtained data comport with literary

Simultaneous measurements of particle number size distributions at ground level and 260 m on a meteorological tower in urban Beijing, China

Science.gov (United States)

Du, Wei; Zhao, Jian; Wang, Yuying; Zhang, Yingjie; Wang, Qingqing; Xu, Weiqi; Chen, Chen; Han, Tingting; Zhang, Fang; Li, Zhanqing; Fu, Pingqing; Li, Jie; Wang, Zifa; Sun, Yele

2017-06-01

Despite extensive studies into the characterization of particle number size distributions at ground level, real-time measurements above the urban canopy in the megacity of Beijing have never been performed to date. Here we conducted the first simultaneous measurements of size-resolved particle number concentrations at ground level and 260 m in urban Beijing from 22 August to 30 September. Our results showed overall similar temporal variations in number size distributions between ground level and 260 m, yet periods with significant differences were also observed. Particularly, accumulation-mode particles were highly correlated (r2 = 0. 85) at the two heights, while Aitken-mode particles presented more differences. Detailed analysis suggests that the vertical differences in number concentrations strongly depended on particle size, and particles with a mobility diameter between 100 and 200 nm generally showed higher concentrations at higher altitudes. Particle growth rates and condensation sinks were also calculated, which were 3.2 and 3.6 nm h-1, and 2.8 × 10-2 and 2.9 × 10-2 s-1, at ground level and 260 m, respectively. By linking particle growth with aerosol composition, we found that organics appeared to play an important role in the early stage of the growth (09:00-12:00 LT) while sulfate was also important during the later period. Positive matrix factorization of size-resolved number concentrations identified three common sources at ground level and 260 m, including a factor associated with new particle formation and growth events (NPEs), and two secondary factors that represent photochemical processing and regional transport. Cooking emission was found to have a large contribution to small particles and showed much higher concentration at ground level than 260 m in the evening. These results imply that investigation of NPEs at ground level in megacities needs to consider the influences of local cooking emissions. The impacts of regional emission controls on

The Use of Mg(OH2 in the Final Peroxide Bleaching Stage of Wheat Straw Pulp

Directory of Open Access Journals (Sweden)

Yan-Lan Liu

2013-11-01

Full Text Available Magnesium-based alkali is an attractive alkaline source for the peroxide bleaching of high-yield pulp. However, little information is available on Mg(OH2 application in the final peroxide bleaching stage of wheat straw pulp. The use of Mg(OH2 was demonstrated as a partial replacement for NaOH in the peroxide bleaching of a chelated oxygen-delignified wheat straw pulp. The yield, viscosity, and strength properties of bleached pulp significantly increased with increasing replacement ratio of Mg(OH2, while the chemical oxygen demand load (COD of filtrate was decreased. For similar brightness of bleached pulp at a 24% replacement ratio of Mg(OH2, the tensile and tear indices were higher, by 2.1 Nm.g-1 and 1.75 mN*m2.g-1, respectively, than that of control pulp bleached with NaOH as the sole alkaline source. When the MgSO4 was eliminated and the dosage of Na2SiO3 was decreased in the bleaching process, the tear and burst indices of the bleached pulp were also enhanced, with the brightness maintained. Scanning electron microscopy (SEM showed that more swelling occurred in the fibers of bleached pulp from the Mg(OH2-based bleaching process. Fiber analysis indicated that peroxide bleaching with Mg(OH2 increased the proportion of fiber lengths between 0.20 to 1.20 mm and 1.20 to 7.60 mm.

Interplay of Mg2+, ADP, and ATP in the cytosol and mitochondria: unravelling the role of Mg2+ in cell respiration.

Science.gov (United States)

Gout, Elisabeth; Rébeillé, Fabrice; Douce, Roland; Bligny, Richard

2014-10-28

In animal and plant cells, the ATP/ADP ratio and/or energy charge are generally considered key parameters regulating metabolism and respiration. The major alternative issue of whether the cytosolic and mitochondrial concentrations of ADP and ATP directly mediate cell respiration remains unclear, however. In addition, because only free nucleotides are exchanged by the mitochondrial ADP/ATP carrier, whereas MgADP is the substrate of ATP synthase (EC 3.6.3.14), the cytosolic and mitochondrial Mg(2+) concentrations must be considered as well. Here we developed in vivo/in vitro techniques using (31)P-NMR spectroscopy to simultaneously measure these key components in subcellular compartments. We show that heterotrophic sycamore (Acer pseudoplatanus L.) cells incubated in various nutrient media contain low, stable cytosolic ADP and Mg(2+) concentrations, unlike ATP. ADP is mainly free in the cytosol, but complexed by Mg(2+) in the mitochondrial matrix, where [Mg(2+)] is tenfold higher. In contrast, owing to a much higher affinity for Mg(2+), ATP is mostly complexed by Mg(2+) in both compartments. Mg(2+) starvation used to alter cytosolic and mitochondrial [Mg(2+)] reversibly increases free nucleotide concentration in the cytosol and matrix, enhances ADP at the expense of ATP, decreases coupled respiration, and stops cell growth. We conclude that the cytosolic ADP concentration, and not ATP, ATP/ADP ratio, or energy charge, controls the respiration of plant cells. The Mg(2+) concentration, remarkably constant and low in the cytosol and tenfold higher in the matrix, mediates ADP/ATP exchange between the cytosol and matrix, [MgADP]-dependent mitochondrial ATP synthase activity, and cytosolic free ADP homeostasis.

Hydrothermal Formation of the Head-to-Head Coalesced Szaibelyite MgBO2(OH Nanowires

Directory of Open Access Journals (Sweden)

Zhu Wancheng

2009-01-01

Full Text Available Abstract The significant effect of the feeding mode on the morphology and size distribution of the hydrothermal synthesized MgBO2(OH is investigated, which indicates that, slow dropping rate (0.5 drop s−1 and small droplet size (0.02 mL d−1 of the dropwise added NaOH solution are favorable for promoting the one-dimensional (1D preferential growth and thus enlarging the aspect ratio of the 1D MgBO2(OH nanostructures. The joint effect of the low concentration of the reactants and feeding mode on the hydrothermal product results in the head-to-head coalesced MgBO2(OH nanowires with a length of 0.5–9.0 μm, a diameter of 20–70 nm, and an aspect ratio of 20–300 in absence of any capping reagents/surfactants or seeds.

Formation of Mg(OH)2 nanowhiskers on LTA zeolite surfaces using a sol–gel method

KAUST Repository

Liu, Junqiang

2011-09-20

A facile three step sol-gel-precipitation process is used to synthesize Mg(OH)2 nanowhiskers on micron-sized zeolite 5A particle surfaces at room temperature. The putative amorphous gelation product, Mg(OH) n(OR)2-n, forms first by a controlled hydrolysis and condensation reaction involving magnesium isopropoxide and water, ultimately leading to precipitation to form Mg(OH)2 structures on the zeolite surface. The optimum conditions for one dimensional Mg(OH)2 whisker formation are found to be six times the stoichiometric amount of water using 1 M HCl as the catalyst for the sol-gel reaction. The one-dimensional Mg(OH) 2 whiskers have an average diameter of 5-10 nm and length of 50-100 nm. The zeolite micropores are not affected by the Mg(OH)2 whiskers formed on the surface. The surface roughened zeolite 5A, with a Mg(OH) 2 content of about 9 wt%, showed improved adhesion between the zeolite and the polymer in a mixed-matrix composite membrane. © 2011 Springer Science+Business Media, LLC.

Intrinsic flux pinning mechanisms in different thickness MgB2 films

Directory of Open Access Journals (Sweden)

C. Yang

2017-03-01

Full Text Available MgB2 films in four thickness (60 nm, 200nm, 600nm and 1μm have been fabricated by hybrid physical–chemical vapor deposition technique (HPCVD. By measuring the magnetization hysteresis loops and the resistivity, we have obtained the transport and magnetic properties of the four films. After that, the pinning mechanisms in them were discussed. Comparing the pinning behaviors in these ultrathin films, thin films and thick films, it was found that there exist different pinning types in MgB2 films of different thickness. In combination with the study of the surface morphology, cross-section and XRD results, we concluded that MgB2 films had different growth modes in different growth stages. For thin films, films grew along c axis, and grain boundaries acted as surface pinning. While for thick films, films grew along c axis at first, and then changed to a-b axis growth. As a result, the a-b axis grains acted as strong volume pinning.

MgB{sub 2} superconductors for applications

Energy Technology Data Exchange (ETDEWEB)

Glowacki, B A; Majoros, M; Eisterer, M; Toenies, S; Weber, H W; Fukutomi, M; Komori, K; Togano, K

2003-05-01

The paper presents up to date results on MgB{sub 2} filamentary conductors and coated conductors from the point of view of their possible applications. Basic physical parameters of MgB{sub 2} compound relevant to conductor design are introduced. The correlation between the slope of the irreversibility line, critical temperature and critical current density is discussed with respect to the conductor performance and applicability. The possible origin of the observed anomalous decrease of ac susceptibility at 50 K in copper clad in situ powder-in-tube MgB{sub 2} wires is presented. Some numerical results on critical currents, thermal stability and ac losses of the MgB{sub 2} multifilamentary and coated conductors with magnetic cladding of their filaments are given.

Hypovolemia During Early Exposure to 2,800 m Altitude: Effect of Rehydration

Science.gov (United States)

Greenleaf, J. E.; Farrell, P. A.; Loomis, J. L.; Fedele, M.; West, J.; Roessler, A.; Hinghofer-Szalkay, H.

1997-01-01

The mechanism for reduction of total body water and plasma volume (PV) during initial exposure to acute attitude (ALT) is not clear. Ten man (25+/-SD 3yr. 1.99+/-0.l9sq m) were confined (sitting) for 12 hr in a chamber a 2800m ALT or at 305m(ground). They ate a controlled breakfast (450 kcal + 3ml/kg H2O) on the ground, and lunch and dinner at ALT for a total daily intake of 2,850 kcal (14%PRO, 67%CHO, 16%FAT, 26gNaCl). At hr 10 they consumed fluid-electrolyte drinks or water (12ml/kg, 948ml/day) with sessions at weekly intervals: (a) 185mEq/L Na, 283mOsm/kg; (b) 21.6Na, 365mOsm: and (c) water at ALT: and (d) water on the ground. After 10 hr at ALT%(Delta)PV(Hb-Hct) decreased (P<0.05) by (a) 9.0+/-SE1.5%, (b) 6.2+/-1.7%, (c) 7.4+/-2.2%. and (d) 9.0+/-2.4%. respectively. After drinking at 1200 hr PV increased by (a) 8.3% (P<0.05), (b) 2.8% (NS), (c) -0.9% (NS). and (d) by 0.8% (NS). respectively. The ground-induced hypovolemia suggests a confinement rather than an ALT effect. The increase in PV after the NaCl-NaCitrate drink (a) indicates that drink composition is mom important than as Osm for restoring PV in these Conditions.

Comparing the Electrochemical Performance of LiFePO4/C Modified by Mg Doping and MgO Coating

Directory of Open Access Journals (Sweden)

Jianjun Song

2013-01-01

Full Text Available Supervalent cation doping and metal oxide coating are the most efficacious and popular methods to optimize the property of LiFePO4 lithium battery material. Mg-doped and MgO-coated LiFePO4/C were synthesized to analyze their individual influence on the electrochemical performance of active material. The specific capacity and rate capability of LiFePO4/C are improved by both MgO coating and Mg doping, especially the Mg-doped sample—Li0.985Mg0.015FePO4/C, whose discharge capacity is up to 163 mAh g−1, 145.5 mAh g−1, 128.3 mAh g−1, and 103.7 mAh g−1 at 1 C, 2 C, 5 C, and 10 C, respectively. The cyclic life of electrode is obviously increased by MgO surface modification, and the discharge capacity retention rate of sample LiFePO4/C-MgO2.5 is up to 104.2% after 100 cycles. Comparing samples modified by these two methods, Mg doping is more prominent on prompting the capacity and rate capability of LiFePO4, while MgO coating is superior in terms of improving cyclic performance.

First-principles Study of the Electronic Structure and Optical Properties of MgH2

Science.gov (United States)

Alford, Ashley; Chou, Mei-Yin

2003-03-01

It has been noticed that magnesium might play an interesting role in recently discovered switchable-mirror systems. For example, the films of rare earth and magnesium alloys are found to be superior to the pure rare-earth samples in maximum transparency and mirror-state reflectivity [1]. Moreover, the magnesium-rich Ni-Mg alloy films turned out to be a switchable-mirror system without rare earths [2]. In both cases, pure transparent MgH2 is reversibly formed when these alloys take up hydrogen. In order to model the optical properties of these films, we need to know the electronic and optical properties of MgH2. In this work, we investigate its bonding characteristics, band structure, and dielectric properties with first-principles theoretical methods. The stability of the crystal and the bonding are studied using density functional theory and pseudopotential methods. The excited state properties (the quasiparticle spectra) are studied by many-body perturbation theory within the so-called GW approximation in which the electronic self-energy is approximated by the full Green's function (G) times the screened Coulomb interaction (W). We will report the results for both the rutile-structured alpha-MgH2 and the low-symmetry gamma-MgH2. [1] P. van der Sluis, M. Ouwerkerk, and P. A. Duine, Appl. Phys. Lett. 70, 3356 (1997). [2] T. J. Richardson, J. L. Slack, R. D. armitage, R. Kostecki, B. Farangis, and M. D. Rubin, Appl. Phys. Lett. 78, 3047 (2001).

Mechanically activated self-propagated high-temperature synthesis of nanometer-structured MgB2

International Nuclear Information System (INIS)

Radev, D.D.; Marinov, M.; Tumbalev, V.; Radev, I.; Konstantinov, L.

2005-01-01

Nanometer-sized MgB 2 was prepared via a two-step modification of the mechanically activated self-propagated high-temperature synthesis. The experimental conditions and some structural and phase characteristics of the synthesized product are reported. It is shown that a single-phase material can be prepared after 2 h of intense mechanical treatment of the starting magnesium and boron powders and a synthesis induced at a current-pulse density of 30 A cm -2 . The average size of MgB 2 particles synthesized in this way is 70-80 nm. It is also shown that using the same reagents and the 'classic' high-temperature interaction at 850 deg C with a protective atmosphere of pure Ar, mean particle size of the MgB 2 obtained is 50 μm

Sojourn time asymptotics in the M/G/1 processor sharing queue

NARCIS (Netherlands)

A.P. Zwart (Bert); O.J. Boxma (Onno)

1998-01-01

textabstractWe show for the M/G/1 processor sharing queue that the service time distribution is regularly varying of index $-nu$, $nu$ non-integer, iff the sojourn time distribution is regularly varying of index $-nu $. This result is derived from a new expression for the Laplace-Stieltjes transform

Crystal structure of the high-affinity Na+,K+-ATPase–ouabain complex with Mg2+ bound in the cation binding site

DEFF Research Database (Denmark)

Laursen, Mette; Yatime, Laure; Nissen, Poul

2013-01-01

of ouabain and the side chains of αM1, αM2, and αM6. Furthermore, the structure reveals that cation transport site II is occupied by Mg2+, and crystallographic studies indicate that Rb+ and Mn2+, but not Na+, bind to this site. Comparison with the low-affinity [K2]E2–MgFx–ouabain structure [Ogawa et al...

Ecological survey of M-Field, Edgewood Area Aberdeen Proving Ground, Maryland

Energy Technology Data Exchange (ETDEWEB)

Downs, J.L.; Eberhardt, L.E.; Fitzner, R.E.; Rogers, L.E.

1991-12-01

An ecological survey was conducted on M-Field, at the Edgewood Area, Aberdeen Proving Ground, Maryland. M-Field is used routinely to test army smokes and obscurants, including brass flakes, carbon fibers, and fog oils. The field has been used for testing purposes for the past 40 years, but little documented history is available. Under current environmental regulations, the test field must be assessed periodically to document the presence or potential use of the area by threatened and endangered species. The M-Field area is approximately 370 acres and is part of the US Army's Edgewood Area at Aberdeen Proving Ground in Harford County, Maryland. The grass-covered field is primarily lowlands with elevations from about 1.0 to 8 m above sea level, and several buildings and structures are present on the field. The ecological assessment of M-Field was conducted in three stages, beginning with a preliminary site visit in May to assess sampling requirements. Two field site visits were made June 3--7, and August 12--15, 1991, to identify the biota existing on the site. Data were gathered on vegetation, small mammals, invertebrates, birds, large mammals, amphibians, and reptiles.

Ecological survey of M-Field, Edgewood Area Aberdeen Proving Ground, Maryland

Energy Technology Data Exchange (ETDEWEB)

Downs, J.L.; Eberhardt, L.E.; Fitzner, R.E.; Rogers, L.E.

1991-12-01

An ecological survey was conducted on M-Field, at the Edgewood Area, Aberdeen Proving Ground, Maryland. M-Field is used routinely to test army smokes and obscurants, including brass flakes, carbon fibers, and fog oils. The field has been used for testing purposes for the past 40 years, but little documented history is available. Under current environmental regulations, the test field must be assessed periodically to document the presence or potential use of the area by threatened and endangered species. The M-Field area is approximately 370 acres and is part of the US Army`s Edgewood Area at Aberdeen Proving Ground in Harford County, Maryland. The grass-covered field is primarily lowlands with elevations from about 1.0 to 8 m above sea level, and several buildings and structures are present on the field. The ecological assessment of M-Field was conducted in three stages, beginning with a preliminary site visit in May to assess sampling requirements. Two field site visits were made June 3--7, and August 12--15, 1991, to identify the biota existing on the site. Data were gathered on vegetation, small mammals, invertebrates, birds, large mammals, amphibians, and reptiles.

A study on preparation and hydriding of β-Mg2Al3 and γ-Mg17Al12

International Nuclear Information System (INIS)

Hadi Suwarno

2009-01-01

The mechanism of the synthetic formation of β-Mg 2 Al 3 and γ-Mg 17 Al 12 has been studied. Mechanical alloying of Mg and Al powders with the atomic ratio of Mg:Al = 2:3 in toluene solution yields β-Mg 2 Al 3 compound after milling for 30 h. The γ-Mg 17 Al 12 can be formed by heating the β-Mg 2 Al 3 at 430°C under high vacuum. The measured hydrogen capacities of β-Mg 2 Al 3 and γ-Mg 17 Al 12 as hydride at 300°C are 3.2 and 4.9 wt%, respectively. Microstructure of the Mg-Al specimen shows that on hydriding at 300°C the polygonal shape of the γ-Mg 17 Al 12 changes into irregular shapes which are composed of γ-MgH 2 and Al. (author)

Observation of meander pattern in signals from superconducting MgB{sub 2} detector by scanning pulsed laser imaging

Energy Technology Data Exchange (ETDEWEB)

Ishida, Takekazu, E-mail: ishida@center.osakafu-u.ac.jp [Department of Physics and Electronics, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8531 (Japan); Institute for Nanofabrication Research, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8531 (Japan); Yagi, Ikutaro; Yoshioka, Naohito; Huy, Ho Thanh [Department of Physics and Electronics, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8531 (Japan); Yotsuya, Tsutomu [Institute for Nanofabrication Research, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8531 (Japan); Nanoscience and Nanotechnology Research Center, Osaka Prefecture University, 2-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8570 (Japan); Shimakage, Hisashi [Department of Electrical and Electronic Engineering, College of Engineering, 4-12-1, Nakanarusawa, Hitachi, Ibaraki 316-8511 (Japan); Miki, Shigehito [Kansai Advanced Research Center, National Institute of Information and Communications Technology, 588-2 Iwaoka-cho, Nishi-ku, Kobe, Hyogo 651-2429 (Japan); Wang, Zhen [Institute for Nanofabrication Research, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8531 (Japan); Kansai Advanced Research Center, National Institute of Information and Communications Technology, 588-2 Iwaoka-cho, Nishi-ku, Kobe, Hyogo 651-2429 (Japan)

2013-01-15

Highlights: ► We fabricate a superconducting MgB{sub 2} meander detector as a solid-state neutron detector. ► MgB{sub 2} detector uses XYZ stage, optical fiber and focused lens to scan as a microscope. ► The 6 μm line-and-space in meandering pattern can be resolved in signals against pulsed laser. -- Abstract: Superconducting MgB{sub 2} meander detector has been imaged by scanning a spot of 1.5-μm focused pulsed laser. The superconducting detector using high-quality {sup 10}B-enriched MgB{sub 2} thin films at higher operating temperatures has been fabricated to utilize a resistance change induced by the nuclear energy of {sup 10}B and neutron. The MgB{sub 2} detector consists of a 200-nm-thick MgB{sub 2} thin-film meander line, a 300-nm-thick SiO protective layer, and 150-nm-thick Nb electrodes with 1-μm MgB{sub 2} wires. The devices were placed in a 4 K refrigerator to control at a certain temperature below T{sub c}. A scanning laser spot can be used by the combination of the XYZ piezo-drive stage and an optical fibre with an aspheric focused lens. The measurement system is fully controlled by LabVIEW based software. We succeeded in observing a line-and-space image of a meandering pattern by analysing response signals.

Conductivity, XRD, and FTIR studies of New Mg2+-ion-conducting solid polymer electrolytes: [PEG: Mg(CH3COO)2

International Nuclear Information System (INIS)

Polu, Anji Reddy; Kumar, Ranveer; Causin, Valerio; Neppalli, Ramesh

2011-01-01

Solid polymer electrolytes based on poly (ethylene glycol) (PEG) doped with Mg(CH 3 COO) 2 have been prepared by using the solution-casting method. The X-ray diffraction patterns of PEG with Mg(CH 3 COO) 2 salt indicated a decrease in the degree of crystallinity with increasing concentration of the salt. The complexation of Mg(CH 3 COO) 2 salt with the polymer was confirmed by using Fourier transform infrared spectroscopy (FTIR) studies. The ionic conductivity was measured for the [PEG: Mg(CH 3 COO) 2 ] system in the frequency range 50 Hz - 1 MHz. The addition of Mg salt was found to improve the ionic conductivity significantly. The 15-wt-% Mg(CH 3 COO) 2 -doped system had a maximum conductivity of 1.07 x 10 -6 S/cm at 303 K. The conductance spectrum shows two distinct regions: a dc plateau and a dispersive region. The temperature dependence of the ionic conductivity reveals the conduction mechanism to be an Arrhenius-type thermally activated process.

Effects of Mg substitution on the structural and magnetic properties of Co0.5Ni0.5-x Mg x Fe2O4 nanoparticle ferrites

Science.gov (United States)

R, M. Rosnan; Z, Othaman; R, Hussin; Ali, A. Ati; Alireza, Samavati; Shadab, Dabagh; Samad, Zare

2016-04-01

In this study, nanocrystalline Co-Ni-Mg ferrite powders with composition Co0.5Ni0.5-x Mg x Fe2O4 are successfully synthesized by the co-precipitation method. A systematic investigation on the structural, morphological and magnetic properties of un-doped and Mg-doped Co-Ni ferrite nanoparticles is carried out. The prepared samples are characterized using x-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), and vibrating sample magnetometry (VSM). The XRD analyses of the synthesized samples confirm the formation of single-phase cubic spinel structures with crystallite sizes in a range of ˜ 32 nm to ˜ 36 nm. The lattice constant increases with increasing Mg content. FESEM images show that the synthesized samples are homogeneous with a uniformly distributed grain. The results of IR spectroscopy analysis indicate the formation of functional groups of spinel ferrite in the co-precipitation process. By increasing Mg2+ substitution, room temperature magnetic measurement shows that maximum magnetization and coercivity increase from ˜ 57.35 emu/g to ˜ 61.49 emu/g and ˜ 603.26 Oe to ˜ 684.11 Oe (1 Oe = 79.5775 A·m-1), respectively. The higher values of magnetization M s and M r suggest that the optimum composition is Co0.5Ni0.4Mg0.1Fe2O4 that can be applied to high-density recording media and microwave devices. Project supported by the Ibnu Sina Institute for Scientific and Industrial Research, Physics Department of Universiti Teknologi Malaysia and the Ministry of Education Malaysia (Grant Nos. Q.J130000.2526.04H65).

The Influence of MgH2 on the Assessment of Electrochemical Data to Predict the Degradation Rate of Mg and Mg Alloys

Directory of Open Access Journals (Sweden)

Wolf-Dieter Mueller

2014-06-01

Full Text Available Mg and Mg alloys are becoming more and more of interest for several applications. In the case of biomaterial applications, a special interest exists due to the fact that a predictable degradation should be given. Various investigations were made to characterize and predict the corrosion behavior in vitro and in vivo. Mostly, the simple oxidation of Mg to Mg2+ ions connected with adequate hydrogen development is assumed, and the negative difference effect (NDE is attributed to various mechanisms and electrochemical results. The aim of this paper is to compare the different views on the corrosion pathway of Mg or Mg alloys and to present a neglected pathway based on thermodynamic data as a guideline for possible reactions combined with experimental observations of a delay of visible hydrogen evolution during cyclic voltammetry. Various reaction pathways are considered and discussed to explain these results, like the stability of the Mg+ intermediate state, the stability of MgH2 and the role of hydrogen overpotential. Finally, the impact of MgH2 formation is shown as an appropriate base for the prediction of the degradation behavior and calculation of the corrosion rate of Mg and Mg alloys.

Photocatalytic degradation of methylene blue on magnetically separable MgFe2O4 under visible light irradiation

International Nuclear Information System (INIS)

Shahid, Muhammad; Jingling, Liu; Ali, Zahid; Shakir, Imran; Warsi, Muhammad Farooq; Parveen, Riffat; Nadeem, Muhammad

2013-01-01

A magnetically separable single-phase MgFe 2 O 4 photocatalyst with a spinel crystal structure was synthesized by using the solid-state reaction method. The formation of spinel structure is confirmed by X-ray diffraction and Fourier transform infrared spectroscopy. The magnetic measurements showed that the photocatalyst material can be separated from water when an external magnetic field is added and redispersed into water solution after the external magnetic field is eliminated. It is one of the promising photocatalysts for waste water treatment. The photocatalytic activity of MgFe 2 O 4 was investigated by using the photo-decomposition of methylene blue dye under visible light. The photoelectrochemical property of the MgFe 2 O 4 was studied by measuring their photocurrent–potential behavior in 1 M NaOH electrolyte under AM 1.5100 mW cm −2 illumination. - Graphical abstract: Highly efficient magnetically separable MgFe 2 O 4 photocatalyst for organic based impurities decomposition as well as for the production of H 2 gas was synthesized and characterized successfully (a) MgFe 2 O 4 photocatalyst in polluted water, (b) The photocatalyst (MgFe 2 O 4 ) is being attracted toward magnetic field for separation, (c) Hysteresis loop of MgFe 2 O 4 showing magnetic behavior. Highlights: ► New photocatalyst working in the visible range have been synthesized by facile cheap route. ► MgFe 2 O 4 photocatalyst showed well defined magnetically separable behavior. ► Excellent water splitting characteristics to produce H 2 was observed under visible light irradiation

Ouro Verde MG 2: nova cultivar de mungo-verde para Minas Gerais Ouro Verde MG 2: new mungbean cultivar for Minas Gerais State, Brazil

Directory of Open Access Journals (Sweden)

Rogério F. Vieira

2002-03-01

Full Text Available Dentre várias linhagens introduzidas do "Asian Vegetable Research and Development Center" (AVRDC, sobressaiu a linhagem VC 3984-B-2-B-4-1-B, que recebeu o nome de Ouro Verde MG 2. Suas sementes são verde-brilhantes e o peso de 1000 unidades varia de 43 a 51 g. O início da floração ocorre em torno de 33 dias após a emergência e a primeira vagem madura surge entre 23 e 33 dias. Por se tratar de espécie de maturação desuniforme, podem ser necessárias duas a quatro colheitas. As plantas podem atingir 95 cm de altura. As vagens são marrom-escuras e concentram-se na parte superior da planta. É suscetível a duas doenças que geralmente aparecem no final do ciclo de vida do mungo-verde: míldio-pulverulento (Erysiphe polygoni e mancha-foliar-de-cercospora (Cercospora canescens. A 'Ouro Verde MG 2' é resistente ao acamamento, e o seu rendimento, em três ensaios instalados em dezembro, janeiro e fevereiro, variou de 1,5 a 2,0 t/ha. Esses rendimentos foram, em média, 12% superior ao da cultivar Ouro Verde.Among many accessions introduced from Asian Vegetable Research and Development Center (AVRDC, the VC 3984-B-2-B-4-1-B stood out and was named 'Ouro Verde MG 2'. The seeds are bright green and 1000-seed weight ranges from 43 to 51 g. Flowering starts approximately 33 days after emergence and the first pod ripens between 23 and 33 days later. As mungbean is a non-uniform maturation species, two to four harvests could be necessary. The plant can reach 95 cm high. The pods are dark brown and concentrated in the upper canopy. This cv. is susceptible to two diseases which generally appear late in the crop: powdery mildew (Erysiphe polygoni and cercospora leaf spot (Cercospora canescens. 'Ouro Verde MG 2' is resistant to lodging. The yield measured in three experiments carried out in December, January, and February, ranged from 1.5 to 2.0 t/ha. In average, these yields were 12% superior than the achieved by the cultivar 'Ouro Verde'.

Thin films of thermoelectric compound Mg2Sn deposited by co-sputtering assisted by multi-dipolar microwave plasma

International Nuclear Information System (INIS)

Le-Quoc, H.; Lacoste, A.; Hlil, E.K.; Bes, A.; Vinh, T. Tan; Fruchart, D.; Skryabina, N.

2011-01-01

Highlights: → Mg 2 Sn thin films deposited by plasma co-sputtering, on silicon and glass substrates. → Formation of nano-grained polycrystalline films on substrates at room temperature. → Structural properties vary with target biasing and target-substrate distance. → Formation of the hexagonal phase of Mg 2 Sn in certain deposition conditions. → Power factor ∼5.0 x 10 -3 W K -2 m -1 for stoichiometric Mg 2 Sn films doped with ∼1 at.% Ag. - Abstract: Magnesium stannide (Mg 2 Sn) thin films doped with Ag intended for thermoelectric applications are deposited on both silicon and glass substrates at room temperature by plasma assisted co-sputtering. Characterization by scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction confirms the formation of fine-grained polycrystalline thin films with thickness of 1-3 μm. Stoichiometry, microstructure and crystal structure of thin films are found to vary with target biasing and the distance from targets to substrate. Measurements of electrical resistivity and Seebeck coefficient at room temperature show the maximum power factor of ∼5.0 x 10 -3 W K -2 m -1 for stoichiometric Mg 2 Sn thin films doped with ∼1 at.% Ag.

Intrinsic Conductivity in Magnesium-Oxygen Battery Discharge Products: MgO and MgO2

DEFF Research Database (Denmark)

Smith, Jeffrey G.; Naruse, Junichi; Hiramatsu, Hidehiko

2017-01-01

Nonaqueous magnesium–oxygen (or “Mg-air”) batteries are attractive next generation energy storage devices due to their high theoretical energy densities, projected low cost, and potential for rechargeability. Prior experiments identified magnesium oxide, MgO, and magnesium peroxide, MgO2...

Catalytic effect of Ni, Mg2Ni and Mg2NiH4 upon hydrogen desorption from MgH2

Czech Academy of Sciences Publication Activity Database

Čermák, Jiří; David, Bohumil

2011-01-01

Roč. 36, č. 21 (2011), s. 13614-13620 ISSN 0360-3199 R&D Projects: GA ČR GA106/09/0814; GA ČR(CZ) GAP108/11/0148 Institutional research plan: CEZ:AV0Z20410507 Keywords : MgH2 * Hydrogen storage * Hydrogen desorption * Catalysis Subject RIV: JG - Metallurgy Impact factor: 4.054, year: 2011

Effect of MgCl2 addition on the sintering behavior of MgAl2O4 spinel and formation of nano-particles

Directory of Open Access Journals (Sweden)

Mohammadi F.

2014-01-01

Full Text Available In this paper, the effect of MgCl2 addition on the sintering behavior of MgAl2O4 spinel produced via oxide mixture method was investigated. For this reason, the stoichiometric mixture of magnesite and calcined alumina as raw materials was calcined at 1100°C. The calcined mixture was milled, pressed and then, fired at 1300 and 1500°C after addition of various amounts of MgCl2. Besides, the physical properties, phase composition and microstructure of fired samples were investigated. The results showed that MgCl2 addition has great effect on the densification and particle size of spinel. Besides, MgCl2 addition increases the amount of spinel phase at all firing temperatures. Due to the decomposition of MgCl2 and then formation of ultra-fine MgO particles, the nano-sized spinel is formed on the surface of the larger spinel particles.

Effect of amorphous Mg50Ni50 on hydriding and dehydriding behavior of Mg2Ni alloy

International Nuclear Information System (INIS)

Guzman, D.; Ordonez, S.; Fernandez, J.F.; Sanchez, C.; Serafini, D.; Rojas, P.A.; Aguilar, C.; Tapia, P.

2011-01-01

Composite Mg 2 Ni (25 wt.%) amorphous Mg 50 Ni 50 was prepared by mechanical milling starting with nanocrystalline Mg 2 Ni and amorphous Mg 50 Ni 50 powders, by using a SPEX 8000 D mill. The morphological and microstructural characterization of the powders was performed via scanning electron microscopy and X-ray diffraction. The hydriding characterization of the composite was performed via a solid gas reaction method in a Sievert's-type apparatus at 363 K under an initial hydrogen pressure of 2 MPa. The dehydriding behavior was studied by differential thermogravimetry. On the basis of the results, it is possible to conclude that amorphous Mg 50 Ni 50 improved the hydriding and dehydriding kinetics of Mg 2 Ni alloy upon cycling. A tentative rationalization of experimental observations is proposed. - Research Highlights: → First study of the hydriding behavior of composite Mg 2 Ni (25 wt.%) amorphous Mg 50 Ni 50 . → Microstructural characterization of composite material using XRD and SEM was obtained. → An improved effect of Mg 50 Ni 50 on the Mg 2 Ni hydriding behavior was verified. → The apparent activation energy for the hydrogen desorption of composite was obtained.

MgB2 and Mg1-xAlxB2 single crystals: high pressure growth and physical properties

International Nuclear Information System (INIS)

Karpinski, J.; Kazakov, S.M.; Jun, J.; Zhigadlo, N.D.; Angst, M.; Puzniak, R.; Wisniewski, A.

2004-01-01

Single crystals of MgB 2 have been grown with a high pressure cubic anvil technique. They grow via the peritectic decomposition of the MgNB 9 ternary nitride. The crystals are of a size up to 2 x 1 x 0.1 mm 3 with a weight up to 230 μg. Typically they have transition temperatures between 38 and 38.6 K with a width of 0.3-0.5 K. Investigations of the P-T phase diagram prove that the MgB 2 phase is stable at least up to 2190 deg. C at high hydrostatic pressure in the presence of Mg vapor under high pressure. Substitution of aluminum for magnesium in single crystals leads to stepwise decrease of T c . This indicates a possible appearance of superstructures or phases with different T c 's. The upper critical field decreases with Al doping

Structural relaxation and colour in the spinel-magnesiochromite (MgAl2O4-MgCr2O4) and gahnite-zincochromite (ZnAl2O4-ZnCr2O4) solid solution series

Science.gov (United States)

Hålenius, U.; Andreozzi, G. B.; Skogby, H.

2009-04-01

.5 %, respectively, is determined. Based on a Cr-O bond distance for the CrO6 polyhedron in magnesiochromite and zincochromite of 1.995 and 1.991 Å respectively (O'Neill and Dollase, 1994) and applying the ligand field relationship 10Dq?C×R-5 (R equals the M-O distance of the MO6-polyhedron), Cr-O bond distances in gahnite and spinel with Cr-contents at trace levels are determined to 1.959 and 1.969 Å, respectively. These M-O bond distances are considerably longer than the M-O distances determined for end member gahnite and spinel by XRD-methods (1.9137 and 1.9280 Å, respectively; O'Neill and Dollase, 1994) and shows that there is considerable structural relaxation of M-O bonds in the two present spinel series. The relaxation parameter, ɛ, determined from the optical absorption spectra is 0.59 and 0.63 for the ZnAl2-2xCr2xO4 and MgAl2-2xCr2xO4 and series, respectively. These values are lower than those suggested from X-ray absorption spectroscopy (Juhin et al. 2007), which may be explained by second nearest neighbour interactions. In contrast to what may be expected, the interelectronic repulsion parameter, B, for V ICr3+ decreases with increasing Cr-content and apparent Cr-O bond length in both of the present spinel series . This indicates that interactions between Cr-atoms in neighbouring octahedra become important at increasing Cr-content and result in more covalent Cr-O bonds. This in turn suppresses the energy of 4A2g -4T2g (4F) transition (and calculated 10Dq-values) in octahedrally coordinated Cr3+. Consequently, the values of structural relaxation parameters determined from the optical absorption spectra must be regarded as minimum numbers. Literature Juhin, A., Calas, G., Cabaret, D. and Galoisy, L. (2007): Structural relaxation around Cr3+ in MgAl2O4. Physical Review, B76, 054105. O'Neill, H.St.C. and Dollase, W.A. (1994): Crystal structures and cation distributions in simple spinels from powder XRD structure refinements: MgCr2O4, ZnCr2O4, Fe3O4 and the temperature

Structural and electronic properties of Mg and Mg-Nb co-doped TiO2 (101) anatase surface

International Nuclear Information System (INIS)

Sasani, Alireza; Baktash, Ardeshir; Mirabbaszadeh, Kavoos; Khoshnevisan, Bahram

2016-01-01

Highlights: • Formation energy of Mg and Mg-Nb co-doped TiO_2 anatase surface (101) is studied. • Effect of Mg defect to the TiO_2 anatase (101) surface and bond length distribution of the surface is studied and it is shown that Mg defects tend to stay far from each other. • Effect of Mg and Nb to the bond length distribution of the surface studied and it is shown that these defects tend to stay close to each other. • Effects of Mg and Mg-Nb defects on DSSCs using TiO_2 anatase hosting these defects are studied. - Abstract: In this paper, by using density functional theory, Mg and Nb-Mg co-doping of TiO_2 anatase (101) surfaces are studied. By studying the formation energy of the defects and the bond length distribution of the surface, it is shown that Mg defects tend to stay as far as possible to induce least possible lattice distortion while Nb and Mg defects stay close to each other to cause less stress to the surface. By investigating band structure of the surface and changes stemmed from the defects, potential effects of Mg and Mg-Nb co-doping of TiO_2 surface on dye-sensitized solar cells are investigated. In this study, it is shown that the Nb-Mg co-doping could increase J_S_C of the surface while slightly decreasing V_O_C compared to Mg doped surface, which might result in an increase in efficiency of the DSSCs compared to Nb or Mg doped surfaces.

α-MnO2 Nanowires/Graphene Composites with High Electrocatalytic Activity for Mg-Air Fuel Cell

International Nuclear Information System (INIS)

Jiang, Min; He, Hao; Huang, Chen; Liu, Bo; Yi, Wen-Jun; Chao, Zi-Sheng

2016-01-01

Highlights: • α-MnO 2 NWs/graphene was synthesized and studied in Mg-air fuel cell. • The performance of α-MnO 2 NWs/graphene is close to the Pt/C. • The ORR mechanism involves a one-step, quasi-4-electron pathway. • A large area (5 cm*5 cm) cathode was prepared and tested in a full cell. - Abstract: This paper reports the preparation of α-MnO 2 NWs/graphene composites as the cathode catalyst for magnesium-air fuel cell and its excellent electrochemistry performance. The composites are synthesized by self-assembly of α-MnO 2 nan α-MnO 2 NWs/graphene was synthesized and studied in Mg-air fuel cell. α-MnO 2 NWs/graphene was synthesized and studied in Mg-air fuel cell. owires (NWs) on the surface of graphene via a simple hydrothermal method. The α-MnO 2 NWs/graphene composites showed a higher electrochemical activity than the commercial MnO 2 . The oxygen reduction peak of the α-MnO 2 NWs/graphene composites catalyst is tested in a 0.1 M KOH solution at −0.252 V, which is more positive than the commercial MnO 2 (−0.287 V). The ORR limit current density for 28% α-MnO2 NWs/graphene composite is approximately 2.74 mA/cm 2 , which is similar to that of the 20% Pt/C(2.79 mA/cm 2 ) in the same conditions. Based on the Koutecky–Levich plot, the ORR mechanism of the composite involves a one-step, quasi-4-electron pathway. In addition, magnesium-air fuel cell with α-MnO 2 NWs/graphene as catalyst possesses higher current density (140 mA/cm 2 ) and power density (96 mW/cm 2 ) compared to the commercial MnO 2 . This study proves that the cost-effective α-MnO 2 NWs/graphene with higher power generation ability make it possible for the substitute of the noble metals catalyst in the Mg-air fuel cell.

Properties of thymidylate synthetase from Ehrlich ascites carcinoma cells. Effect of Mg2/ and MgATP2-.

Science.gov (United States)

Jastreboff, M; Kedzierska, B; Rode, W

1982-01-15

Ehrlich ascites carcinoma thymidylate synthetase was purified to electrophoretic homogeneity by affinity chromatography on 10-formyl-5,8-dideazofolate-ethyl-Sepharose. Electrophoretic analysis of the formation of the enzyme-5-fluorodeoxyuridylate-5,10-methylenetetrahydrofolate complexes showed the presence of two binding sites for 5-fluorodeoxyuridylate on the enzyme molecule. Molecular weight of the native enzyme was found to be 78,5000, whereas that of its monomer was 38, 500. The apparent Michaelis constants for dUMP and (+/-)-L-5,10-methylenetetrahydrofolate were 1.3 +/- 0.4 and 32.2 +/- 0.7 micrometers respectively. Phosphate acted as a weak inhibitor, competitive toward dUMP. The enzyme reaction exhibited a temperature-dependent change of activation energy, reflected in the binding affinity of dUMP, with a transitional temperature of 35.8 degrees. Both Mg2+ and MgATP2- were strong activators of the enzyme, MgATP2- being more effective.

Theoretical Limiting Potentials in Mg/O2 Batteries

DEFF Research Database (Denmark)

Smith, Jeffrey G.; Naruse, Junichi; Hiramatsu, Hidehiko

2016-01-01

A rechargeable battery based on a multivalent Mg/O2 couple is an attractive chemistry due to its high theoretical energy density and potential for low cost. Nevertheless, metal-air batteries based on alkaline earth anodes have received limited attention and generally exhibit modest performance....... In addition, many fundamental aspects of this system remain poorly understood, such as the reaction mechanisms associated with discharge and charging. The present study aims to close this knowledge gap and thereby accelerate the development of Mg/O2 batteries by employing first-principles calculations...... by the presence of large thermodynamic overvoltages. In contrast, MgO2-based cells are predicted to be much more efficient: superoxide-terminated facets on MgO2 crystallites enable low overvoltages and round-trip efficiencies approaching 90%. These data suggest that the performance of Mg/O2 batteries can...

Fabrication and properties of multifilamentary MgB 2 wires by in-situ powder-in-tube process

Science.gov (United States)

Wang, Q. Y.; Jiao, G. F.; Liu, G. Q.; Xiong, X. M.; Yan, S. C.; Zhang, P. X.; Sulpice, A.; Mossang, E.; Feng, Y.; Yan, G.

2010-11-01

We have fabricated the long TiC-doped MgB2 wires with 6 filaments by in-situ powder-in-tube method using Nb as the barrier and copper as the stabilizer. To improve the strength of wires, the Nb-core was used as the central filament. The transport engineering critical current density (Jce) of the samples sintered at different temperature were measured, which reaches 2.5 × 104 A/cm2 at 4.2 K, 5 T. 100 m MgB2 wires with different diameter were wound into coils and the transport critical current (Ic) of the coil were measured at 30 K in self-field. The Jce value 100 m coil achieves 1.1 × 104 A/cm2 in 1.2 mm wire. The reasons leading to the enhancement of high field Jce were discussed. The results show a good potential to fabricate high performance MgB2 wires and tapes at ambient pressure on an industrial scale.

Trapped field measurements on MgB{sub 2} bulk samples

Energy Technology Data Exchange (ETDEWEB)

Koblischka, Michael; Karwoth, Thomas; Zeng, XianLin; Hartmann, Uwe [Institute of Experimental Physics, Saarland University, P. O. Box 151150, D-66041 Saarbruecken (Germany); Berger, Kevin; Douine, Bruno [University of Lorraine, GREEN, 54506 Vandoeuvre-les-Nancy (France)

2016-07-01

Trapped field measurements were performed on bulk, polycrystalline MgB{sub 2} samples stemming from different sources with the emphasis to develop applications like superconducting permanent magnets ('supermagnets') and electric motors. We describe the setup for the trapped field measurements and the experimental procedure (field cooling, zero-field cooling, field sweep rates). The trapped field measurements were conducted using a cryocooling system to cool the bulk samples to the desired temperatures, and a low-loss cryostat equipped with a room-temperature bore and a maximum field of ±5 T was employed to provide the external magnetic field. The superconducting coil of this cryostat is operated using a bidirectional power supply. Various sweep rates of the external magnetic field ranging between 1 mT/s and 40 mT/s were used to generate the applied field. The measurements were performed with one sample and two samples stacked together. A maximum trapped field of 7 T was recorded. We discuss the results obtained and the problems arising due to flux jumping, which is often seen for the MgB{sub 2} samples cooled to temperatures below 10 K.

Mechanical Properties and Fabrication of Nanostructured Mg_2SiO_4-MgAl_2O_4 Composites by High-Frequency Induction Heated Combustion

International Nuclear Information System (INIS)

Shon, In-Jin; Kang, Hyun-Su; Hong, Kyung-Tae; Doh, Jung-Mann; Yoon, Jin-Kook

2011-01-01

Nanopowders of MgO, Al_2O_3 and SiO_2 were made by high energy ball milling. The rapid sintering of nanostructured MgAl_2O_4-Mg_2SiO_4 composites was investigated by a high-frequency induction heating sintering process. The advantage of this process is that it allows very quick densification to near theoretical density and inhibition of grain growth. Nanocrystalline materials have received much attention as advanced engineering materials with improved physical and mechanical properties. As nanomaterials possess high strength, high hardness, excellent ductility and toughness, undoubtedly, more attention has been paid for the application of nanomaterials. Highly dense nanostructured MgAl_2O_4-Mg_2SiO_4 composites were produced with simultaneous application of 80 MPa pressure and induced output current of total power capacity (15 kW) within 2 min. The sintering behavior, gain size and mechanical properties of MgAl_2O_4-Mg_2SiO_4 composites were investigated.

TL and OSL studies of carbon doped magnesium aluminate (MgAl2O4:C)

Science.gov (United States)

Raj, Sanu S.; Mishra, D. R.; Soni, Anuj; Grover, V.; Polymeris, G. S.; Muthe, K. P.; Jha, S. K.; Tyagi, A. K.

2016-10-01

The MgAl2O4:C has been synthesized by using two different methods by electron gun and vacuum assisted melting of MgAl2O4 in presence of graphite. The MgAl2O4:C phosphor thus developed by these two different methods have similar types of the TL/OSL defects with multiple overlapping TL glow peaks from 100 °C to 400 °C. The Computerized Curve De-convolution Analysis (CCDA) has been used to measure TL parameters such as thermal trap depth, frequency factor and order of kinetic associated with charge transfer process in TL phenomenon. The investigated TL/OSL results show that these two methods of incorporating carbon in MgAl2O4 have generated closely resemble the defects of similar types in MgAl2O4:C lattice. However, the MgAl2O4:C synthesized by electron gun shows relatively larger concentration of the TL/OSL defects as compared to MgAl2O4:C synthesized using vacuum assisted melting method. The photo-ionization cross-section (PIC) associated with fastest OSL component of MgAl2O4: C is found to be ∼ 0.5 times than that of fastest OSL component of commercially available dosimetric grade α-Al2O3:C. The MgAl2O4:C thus developed shows good dynamic OSL dose linearity from few mGy to 1 Gy. This work reveals that MgAl2O4:C could be developed as potential tissue equivalent OSL / TL material.

Structural and electronic properties of Mg and Mg-Nb co-doped TiO2 (101) anatase surface

Energy Technology Data Exchange (ETDEWEB)

Sasani, Alireza [Department of Science, Karaj Islamic Azad University, Karaj, Alborz, P.O. Box 31485-313 (Iran, Islamic Republic of); Baktash, Ardeshir [Institute of Nano Science and Nano Technology, University of Kashan, Kashan, P.O. Box 87317-51167 (Iran, Islamic Republic of); Mirabbaszadeh, Kavoos, E-mail: mirabbas@aut.ac.ir [Department of Energy Engineering and Physics, Amirkabir University of Technology, Tehran, P. O. Box 15875-4413 (Iran, Islamic Republic of); Khoshnevisan, Bahram [Institute of Nano Science and Nano Technology, University of Kashan, Kashan, P.O. Box 87317-51167 (Iran, Islamic Republic of)

2016-10-30

Highlights: • Formation energy of Mg and Mg-Nb co-doped TiO{sub 2} anatase surface (101) is studied. • Effect of Mg defect to the TiO{sub 2} anatase (101) surface and bond length distribution of the surface is studied and it is shown that Mg defects tend to stay far from each other. • Effect of Mg and Nb to the bond length distribution of the surface studied and it is shown that these defects tend to stay close to each other. • Effects of Mg and Mg-Nb defects on DSSCs using TiO{sub 2} anatase hosting these defects are studied. - Abstract: In this paper, by using density functional theory, Mg and Nb-Mg co-doping of TiO{sub 2} anatase (101) surfaces are studied. By studying the formation energy of the defects and the bond length distribution of the surface, it is shown that Mg defects tend to stay as far as possible to induce least possible lattice distortion while Nb and Mg defects stay close to each other to cause less stress to the surface. By investigating band structure of the surface and changes stemmed from the defects, potential effects of Mg and Mg-Nb co-doping of TiO{sub 2} surface on dye-sensitized solar cells are investigated. In this study, it is shown that the Nb-Mg co-doping could increase J{sub SC} of the surface while slightly decreasing V{sub OC} compared to Mg doped surface, which might result in an increase in efficiency of the DSSCs compared to Nb or Mg doped surfaces.

1.083 μm laser operation in Nd,Mg:LiTaO3 crystal

Science.gov (United States)

Hu, P. C.; Hang, Y.; Li, R.; Gong, J.; Yin, J. G.; Zhao, C. C.; He, X. M.; Yu, T.; Zhang, L. H.; Chen, W. B.; Zhu, Y. Y.

2011-10-01

Nd,Mg:LiTaO3 single crystal with high optical quality was grown by Czochralski technique. Absorption and fluorescence spectra were investigated. The peak absorption cross section at 806.5 nm and peak emission cross section at 1091 nm are 6.81×10-20 and 3.28×10-20 cm2, respectively. The fluorescence lifetime was measured to be 129 μs. With a laser-diode as the pump source, a maximum 375 mW continuous-wave laser output at 1083 nm has been obtained with a slope efficiency of 7.2% with respect to the pump power.

1.083 μm laser operation in Nd,Mg:LiTaO3 crystal

International Nuclear Information System (INIS)

Hu, P C; Hang, Y; Li, R; Gong, J; Yin, J G; Zhao, C C; He, X M; Yu, T; Zhang, L H; Chen, W B; Zhu, Y Y

2011-01-01

Nd,Mg:LiTaO 3 single crystal with high optical quality was grown by Czochralski technique. Absorption and fluorescence spectra were investigated. The peak absorption cross section at 806.5 nm and peak emission cross section at 1091 nm are 6.81×10 -20 and 3.28×10 -20 cm 2 , respectively. The fluorescence lifetime was measured to be 129 μs. With a laser-diode as the pump source, a maximum 375 mW continuous-wave laser output at 1083 nm has been obtained with a slope efficiency of 7.2% with respect to the pump power

Analysis of the Source and Ground Motions from the 2017 M8.2 Tehuantepec and M7.1 Puebla Earthquakes

Science.gov (United States)

Melgar, D.; Sahakian, V. J.; Perez-Campos, X.; Quintanar, L.; Ramirez-Guzman, L.; Spica, Z.; Espindola, V. H.; Ruiz-Angulo, A.; Cabral-Cano, E.; Baltay, A.; Geng, J.

2017-12-01

The September 2017 Tehuantepec and Puebla earthquakes were intra-slab earthquakes that together caused significant damage in broad regions of Mexico, including the states of Oaxaca, Chiapas, Morelos, Puebla, Mexico, and Mexico City. Ground motions in Mexico City have approximately the same angle of incidence from both earthquakes and potentially sample similar paths close to the city. We examine site effects and source terms by analysis of residuals between Ground-Motion Prediction Equations (GMPEs) and observed ground motions for both of these events at stations from the Servicio Sismólogico Nacional, Instituto de Ingeniería, and the Instituto de Geofísica Red del Valle de Mexico networks. GMPEs are a basis for seismic design, but also provide median ground motion values to act as a basis for comparison of individual earthquakes and site responses. First, we invert for finite-fault slip inversions for Tehuantepec with high-rate GPS, static GPS, tide gauge and DART buoy data, and for Puebla with high-rate GPS and strong motion data. Using the distance from the stations with ground motion observations to the derived slip models, we use the GMPEs of Garcia et al. (2005), Zhao et al. (2006), and Abrahamson, Silva and Kamai (2014), to compute predicted values of peak ground acceleration and velocity (PGA and PGV) and response spectral accelerations (SA). Residuals between observed and predicted ground motion parameters are then computed for each recording, and are decomposed into event and site components using a mixed effects regression. We analyze these residuals as an adjustment away from median ground motions in the region to glean information about the earthquake source properties, as well as local site response in and outside of the Mexico City basin. The event and site terms are then compared with available values of stress drop for the two earthquakes, and Vs30 values for the sites, respectively. This analysis is useful in determining which GMPE is most

Reaction rim growth in the system MgO-Al2O3-SiO2 under uniaxial stress

Science.gov (United States)

Götze, Lutz Christoph; Abart, Rainer; Rybacki, Erik; Keller, Lukas M.; Petrishcheva, Elena; Dresen, Georg

2010-07-01

We synthesize reaction rims between thermodynamically incompatible phases in the system MgO-Al2O3-SiO2 applying uniaxial load using a creep apparatus. Synthesis experiments are done in the MgO-SiO2 and in the MgO-Al2O3 subsystems at temperatures ranging from 1150 to 1350 °C imposing vertical stresses of 1.2 to 29 MPa at ambient pressure and under a constant flow of dry argon. Single crystals of synthetic and natural quartz and forsterite, synthetic periclase and synthetic corundum polycrystals are used as starting materials. We produce enstatite rims at forsterite-quartz contacts, enstatite-forsterite double rims at periclase-quartz contacts and spinel rims at periclase-corundum contacts. We find that rim growth under the “dry” conditions of our experiments is sluggish compared to what has been found previously in nominally “dry” piston cylinder experiments. We further observe that the nature of starting material, synthetic or natural, has a major influence on rim growth rates, where natural samples are more reactive than synthetic ones. At a given temperature the effect of stress variation is larger than what is anticipated from the modification of the thermodynamic driving force for reaction due to the storage of elastic strain energy in the reactant phases. We speculate that this may be due to modification of the physical properties of the polycrystals that constitute the reaction rims or by deformation under the imposed load. In our experiments rim growth is very sluggish at forsterite-quartz interfaces. Rim growth is more rapid at periclase-quartz contacts. The spinel rims that are produced at periclase-corundum interfaces show parabolic growth indicating that reaction rim growth is essentially diffusion controlled. From the analysis of time series done in the MgO-Al2O3 subsystem we derive effective diffusivities for the Al2O3 and the MgO components in a spinel polycrystal as D_{MgO} = 1.4 ± 0.2 \\cdot 10^{-15} m2/s and D_{Al_2O_3} = 3.7 ± 0

Insight into poor cycling stability of MgH2 anodes

DEFF Research Database (Denmark)

Huen, Priscilla; Ravnsbæk, Dorthe B.

2017-01-01

. The effects of different preparation methods on cell efficiency and cycle stability are examined, showing that crystallite size reduction and ball milling together with the selected carbon source is important both for increasing capacity and limiting polarization. Furthermore, the conversion mechanism......During recent years, MgH2 has received significant interest as conversion-type anode for Li-ion batteries due to the high theoretical capacity of 2038 mAh/g at ~0.5 V vs. Li+/Li. However, the practical reversible capacity and the cycle stability are generally poor and vary significantly among...... literature reports. The latter may be due to differences in preparation procedures for electrodes as well as the precise cycling conditions. In this study, a series of MgH2 samples was systematically prepared by ball milling with different conductive carbon sources and use of hydrogenation treatments...

Dendrimeric tweezers for recognition of fluorogenic Co{sup 2+}, Mg{sup 2+} and chromogenic Fe{sup 2+}

Energy Technology Data Exchange (ETDEWEB)

Roy, Chandana B.; Meshram, Jyotsna S., E-mail: drjsmeshram@gmail.com

2016-03-15

Dendrimers are the attractive candidature for the formation of metal complexes capable of performing varied application, owing to the presence of multiple terminal groups on the exterior of the molecule has received tremendous attention. Herein, we have synthesized novel dendritic macromolecule (N′E,N‴E,N″‴E,N‴‴′E)-3,3′,3″,3‴-(ethane-1,2-diylbis(azanetriyle)) tetrakis(N'-(2-hydroxybenzyllidene)propanehydrazide) chemosensor L and its metal complexes. In the present study the application in the optical sensing for chromogenic Fe{sup 2+} and fluorogenic Co{sup 2+} and Mg{sup 2+}cation is reported. The dendrimeric chemosensor L and its metal complexes are investigated with the help of FTIR spectroscopy, Nuclear magnetic resonance ({sup 1}H NMR and {sup 13}C NMR), FT Raman Microspectroscopy, fluorescence and UV–visible spectroscopy. Thermal properties are studied using thermal gravimetric analysis. - Highlights: • Dual effect – Chromogenic and fluorogenic. Chemosensor shows chromogenic effect towards Fe{sup 2+} as well as fluorogenic effect towards Co{sup 2+}and Mg{sup 2+} cation. • From Linear fitting calibration plot for computing LOD and LOQ, it was detected that – LOD=32.3 nM, LOQ=97.8 nM. • Jobs Plot – A graph plotted [HG]={(ΔF/Fo)[H]} Vs {[H]v/([H]v+[G]v)} has maxima at 0.33 which corresponds to 1:2 stoichiometry of chemosensor L:Co{sup 2+}.

High surface area niobium oxides as catalysts for improved hydrogen sorption properties of ball milled MgH2

International Nuclear Information System (INIS)

Bhat, V.V.; Rougier, A.; Aymard, L.; Nazri, G.A.; Tarascon, J.-M.

2008-01-01

We report, high surface area (up to 200 m 2 /g) nanocrystalline niobium oxide (so called p-Nb 2 O 5 ) synthesized by 'chimie douce' route and its importance in enhancing the hydrogen sorption properties of MgH 2 . p-Nb 2 O 5 induces faster kinetics than commonly used commercial Nb 2 O 5 (c-Nb 2 O 5 ) when ball milled with MgH 2 (named (MgH 2 ) catalyst ) by reducing the time of desorption from 35 min in (MgH 2 ) c-Nb 2 O 5 to 12 min in (MgH 2 ) p-Nb 2 O 5 at 300 deg. C. The BET surface area of as-prepared Nb 2 O 5 was tuned by heat treatment and its effect on sorption properties was studied. Among them, both p-Nb 2 O 5 and Nb 2 O 5 :350 (p-Nb 2 O 5 heated to 350 deg. C with a BET specific surface area of 46 m 2 /g) desorb 5 wt.% within 12 min, exhibiting the best catalytic activity. Furthermore, thanks to the addition of high surface area Nb 2 O 5 , the desorption temperature was successfully lowered down to 200 deg. C, with a significant amount of desorbed hydrogen (4.5 wt.%). In contrast, the composite (MgH 2 ) c-Nb 2 O 5 shows no desorption at this 'low' temperature

Effects of Mg2+ and adenine nucleotides on thymidylate synthetase from different mouse tumors.

Science.gov (United States)

Rode, W; Jastreboff, M M

1984-01-01

Magnesium ions variably influenced activity of highly purified thymidylate synthetase preparations from different mouse tumors, activating the enzyme from Ehrlich ascites carcinoma (EAC) cells and inhibiting the enzyme from L1210 and L5178Y cells and from 5-fluorodeoxyuridine (FdUrd)-resistant EAC cells. In the presence of Mg2+ in a concentration resulting in either maximum activation or inhibition (25-30 mM) the enzymes from both the sensitive and FdUrd-resistant EAC lines and L5178Y cells were activated by ATP. Under the same conditions of Mg2+ concentration ADP and AMP inhibited the enzyme from the parental but not from the FdUrd-resistant EAC cells.

Hydrogen storage properties of LaMgNi{sub 3.6}M{sub 0.4} (M = Ni, Co, Mn, Cu, Al) alloys

Energy Technology Data Exchange (ETDEWEB)

Yang, Tai [Department of Functional Material Research, Central Iron and Steel Research Institute, Beijing 100081 (China); Key Laboratory of Integrated Exploitation of Baiyun Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Zhai, Tingting; Yuan, Zeming; Bu, Wengang [Department of Functional Material Research, Central Iron and Steel Research Institute, Beijing 100081 (China); Xu, Sheng [Key Laboratory of Integrated Exploitation of Baiyun Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Zhang, Yanghuan, E-mail: zhangyh59@sina.com [Department of Functional Material Research, Central Iron and Steel Research Institute, Beijing 100081 (China); Key Laboratory of Integrated Exploitation of Baiyun Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China)

2014-12-25

Highlights: • La–Mg–Ni system AB{sub 2}-type alloys were prepared by induction melting. • Structures and lattice parameters were analysed by XRD. • Hydrogen absorption/desorption performances were studied. • Mechanisms of hydrogen absorption capacity fading were investigated. - Abstract: LaMgNi{sub 3.6}M{sub 0.4} (M = Ni, Co, Mn, Cu, Al) alloys were prepared through induction melting process. The phase compositions and crystal structures were characterised via X-ray diffraction (XRD). The hydrogen storage properties, including activation performance, hydrogen absorption capacity, cycle stability, alloy particle pulverisation and plateau pressure, were systemically investigated. Results show that Ni, Co, Mn and Cu substitution alloys exhibit multiphase structures comprising the main phase LaMgNi{sub 4} and the secondary phase LaNi{sub 5}. However, the secondary phase of the Al substitution alloy changes into LaAlNi{sub 4}. The lattice parameters and cell volumes of the LaMgNi{sub 4} phase follow the order Ni < Co < Al < Cu < Mn. Activation is simplified through partial substitution of Ni with Al, Cu and Co. The hydrogen absorption capacities of all of the alloys are approximately 1.7 wt.% at the first activation process; however, they rapidly decrease with increasing cycle number. In addition, the stabilities of hydriding and dehydriding cycles decrease in the order Al > Co > Ni > Cu > Mn. Hydriding processes result in numerous cracks and amorphisation of the LaMgNi{sub 4} phase in the alloys. The p–c isotherms were determined by a Sieverts-type apparatus. Two plateaus were observed for the Ni, Co and Al substitution alloys, whereas only one plateau was found for Mn and Cu. This result was caused by the amorphisation of the LaMgNi{sub 4} phase during the hydriding cycles. Reversible absorption and desorption of hydrogen are difficult to achieve. Substitutions of Ni with Co, Mn, Cu and Al significantly influence the reduction of hysteresis between

MgO-hybridized TiO{sub 2} interfacial layers assisting efficiency enhancement of solid-state dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Sakai, Nobuya; Ikegami, Masashi; Miyasaka, Tsutomu, E-mail: miyasaka@toin.ac.jp [Graduate School of Engineering, Toin University of Yokohama, 1614 Kurogane-cho, Aoba, Yokohama, Kanagawa 225-8502 (Japan)

2014-02-10

Interfacial modification of a thin TiO{sub 2} compact layer (T-CL) by hybridization with MgO enhanced the quantum conversion efficiency of solid-state dye-sensitized solar cells (ssDSSCs) comprising a multilayer structure of transparent electrode/T-CL/dye-sensitized mesoporous TiO{sub 2}/hole conductor/metal counter electrode. The Mg(CH{sub 3}COO){sub 2} treatment was employed to introduce a MgO-TiO{sub 2} CL (T/M-CL), which enhanced the physical connection and conduction between the CL and mesoporous semiconductor layer as a consecutive interface, owing to the dehydration reaction of Mg(CH{sub 3}COO){sub 2}. The photocurrent density of ssDSSC was increased 33% by the T/M-CL compared with the T-CL, using an equivalent amount of adsorbed dye. The ssDSSC with the T/M-CL yielded the highest efficiency of 4.02% under irradiation at 100 mW cm{sup −2}. The electrical impedance spectroscopy showed that the charge-transfer resistance (R{sub ct}) of the photoelectrode with T/M-CL was reduced by 300 Ω from the reference non-treated T-CL electrode. Characterized by the intrinsically low R{sub ct} of the compact layer, the T/M-CL is capable of improving the photovoltaic performance of solid-state sensitized mesoscopic solar cells.

From $^{27}$Mg to ${33}$Mg transition to the "Island of inversion"

CERN Document Server

Yordanov, Deyan

Since introduced in nuclear physics, the concept of shell structure and magic numbers has governed our understanding of nuclear matter in atomic nuclei close to stability. Nuclear species with a magic number of protons and/or neutrons are known to be more stable and close to spherical in shape. Experimental studies of 30Ne, 31Na and 32Mg, systems with a closed neutron sd shell (N=20), provide evidence for a ground-state deformation in these nuclei. The observed phenomenon is understood as an inversion of the normal spherical ground-state configuration, expected according to the traditional shell model, with deformed states governed by particle-hole excitations over the N=20 shell gap. The properties of nuclei in this Island of inversion are of particular importance for the theoretical modeling of the region. The present doctoral dissertation reports on the first determination of the nuclear ground-state spins and magnetic moments of 31,33Mg, obtained by means of laser spectroscopy in combination with nuclear...

Chemistry of the M (M=Fe, Ca, Ba-Se-H2O Systems at 25 °C

Directory of Open Access Journals (Sweden)

Fumihiko Hasegawa

2009-09-01

Full Text Available The chemistry of the M (M=Fe, Ca, Ba-Se-H2O systems at 25 °C is reviewed based on our previous papers. In this paper, the phase equilibria in the Fe(III-Se(IV-H2O, Ca-Se(IV,VI-H2O and Ba-Se(IV,VI-H2O systems at 25 °C are discussed. Then, the three-stage process for removal of selenium from industrial waste water [Se(IV,VI < 1,500 mg/L] containing sulfuric acid was introduced. This seems to be a promising process for selenium removal from acidic sulfate waste water containing high concentration levels of selenium to below 0.1 mg/L.

The ternary system K2SO4MgSO4CaSO4

Science.gov (United States)

Rowe, J.J.; Morey, G.W.; Silber, C.C.

1967-01-01

Melting and subsolidus relations in the system K2SO4MgSO4CaSO4 were studied using heating-cooling curves, differential thermal analysis, optics, X-ray diffraction at room and high temperatures and by quenching techniques. Previous investigators were unable to study the binary MgSO4CaSO4 system and the adjacent area in the ternary system because of the decomposition of MgSO4 and CaSO4 at high temperatures. This problem was partly overcome by a novel sealed-tube quenching method, by hydrothermal synthesis, and by long-time heating in the solidus. As a result of this study, we found: (1) a new compound, CaSO4??3MgSO4 (m.p. 1201??C) with a field extending into the ternary system; (2) a high temperature form of MgSO4 with a sluggishly reversible inversion. An X-ray diffraction pattern for this polymorphic form is given; (3) the inversion of ??-CaSO4 (anhydrite) to ??-CaSO4 at 1195??C, in agreement with grahmann; (1) (4) the melting point of MgSO4 is 1136??C and that of CaSO4 is 1462??C (using sealed tube methods to prevent decomposition of the sulphates); (5) calcium langbeinite (K2SO4??2CaSO4) is the only compound in the K2SO4CaSO4 binary system. This resolved discrepancies in the results of previous investigators; (6) a continuous solid solution series between congruently melting K2SOP4??2MgSO4 (langbeinite) and incongruently melting K2SO4??2CaSO4 (calcium langbeinite); (7) the liquidus in the ternary system consists of primary phase fields of K2SO4, MgSO4, CaSO4, langbeinite-calcium langbeinite solid solution, and CaSO4??3MgSO4. The CaSO4 field extends over a large portion of the system. Previously reported fields for the compounds (K2SO4??MgSO4??nCaSO4), K2SO4??3CaSO4 and K2SO4??CaSO4 were not found; (8) a minimum in the ternary system at: 740??C, 25% MgSO4, 6% CaSO4, 69% K2SO4; and ternary eutectics at 882??C, 49% MgSO4, 19% CaSO4, 32% K2SO4; and 880??, 67??5% MgSO4, 5% CaSO4, 27??5% K2SO4. ?? 1967.

Comparison of Ca2+ and Mg2+ enhancing aerobic granulation in SBR

International Nuclear Information System (INIS)

Liu Lin; Gao Dawen; Zhang Min; Fu Yuan

2010-01-01

Two sequencing batch reactors (SBRs) were operated to investigate the effect of Ca 2+ and Mg 2+ augmentation on aerobic granulation. Reactor R1 was augmented with Ca 2+ at 40 mg/L, while Mg 2+ was added to the reactor R2 with 40 mg/L. Results showed that the reactor R1 had a faster granulation process compared with R2, and the mature granules in R1 showed better physical characteristics. However, the mature granules in R2 had the higher production yield of polysaccharides and proteins, and aerobic granules in R2 experienced a faster substrate biodegradation. Microbial and genetic characteristics in mature granules were analyzed using polymerase chain reaction (PCR) and denaturing gradient gel electrophoresis (DGGE) techniques. The results revealed that Mg 2+ addition led to higher microbial diversity in mature granules. In addition, an uncultured bacterium (AB447697) was major specie in R1, and β-proteobacterium was dominant in R2. It can be concluded that Ca 2+ had an important effect on physical properties of aerobic granules, while Mg 2+ played a key role on biological properties during the sludge granulation.

Anodic electrochemical performances of MgCo{sub 2}O{sub 4} synthesized by oxalate decomposition method and electrospinning technique for Li-ion battery application

Energy Technology Data Exchange (ETDEWEB)

Darbar, Devendrasinh [School of Mechanical and Building Science, Vellore Institute of Technology (VIT), Vellore 632014, Tamil Nadu (India); Department of Mechanical Engineering, National University of Singapore, 117576 (Singapore); Department of Physics, National University of Singapore, 117542 (Singapore); Reddy, M.V., E-mail: phymvvr@nus.edu.sg [Department of Physics, National University of Singapore, 117542 (Singapore); Department of Materials Science and Engineering, National University of Singapore, 117546 (Singapore); Sundarrajan, S. [Department of Mechanical Engineering, National University of Singapore, 117576 (Singapore); Pattabiraman, R. [School of Mechanical and Building Science, Vellore Institute of Technology (VIT), Vellore 632014, Tamil Nadu (India); Ramakrishna, S. [Department of Mechanical Engineering, National University of Singapore, 117576 (Singapore); Chowdari, B.V.R. [Department of Physics, National University of Singapore, 117542 (Singapore)

2016-01-15

Highlights: • MgCo{sub 2}O{sub 4} was prepared by oxalate decomposition method and electrospinning technique. • Electrospun MgCo{sub 2}O{sub 4} shows the reversible capacity of 795 and 227 mAh g{sup −1} oxalate decomposition MgCo{sub 2}O{sub 4} after 50 cycle. • Electrospun MgCo{sub 2}O{sub 4} show good cycling stability and electrochemical performance. - Abstract: Magnesium cobalt oxide, MgCo{sub 2}O{sub 4} was synthesized by oxalate decomposition method and electrospinning technique. The electrochemical performances, structures, phase formation and morphology of MgCo{sub 2}O{sub 4} synthesized by both the methods are compared. Scanning electron microscope (SEM) studies show spherical and fiber type morphology, respectively for the oxalate decomposition and electrospinning method. The electrospun nanofibers of MgCo{sub 2}O{sub 4} calcined at 650 °C, showed a very good reversible capacity of 795 mAh g{sup −1} after 50 cycles when compared to bulk material capacity of 227 mAh g{sup −1} at current rate of 60 mA g{sup −1}. MgCo{sub 2}O{sub 4} nanofiber showed a reversible capacity of 411 mAh g{sup −1} (at cycle) at current density of 240 mA g{sup −1}. Improved performance was due to improved conductivity of MgO, which may act as buffer layer leading to improved cycling stability. The cyclic voltammetry studies at scan rate of 0.058 mV/s show main cathodic at around 1.0 V and anodic peaks at 2.1 V vs. Li.

Photoproducts of tetracycline and oxytetracycline involving self-sensitized oxidation in aqueous solutions: Effects of Ca2+ and Mg2+

Institute of Scientific and Technical Information of China (English)

Yong Chen; Hua Li; Zongping Wang; Tao Tao; Chun Hu

2011-01-01

Tetracyclines constitute one of the most important antibiotic families and represent a classic example of phototoxicity.The photoproducts of tetracyclines and their parent compounds have potentially adverse effects on natural ecosystem.In this study,the self-sensitized oxidation products of tetracycline (TC) and oxytetracycline (OTC) were determined and the effects of Ca2+ and Mg2+on self-sensitized degradation were investigated.The Ca2+ and Mg2+ in the natural water sample accounted for enhancement (pH 7.3)and inhibition (pH 9.0) of photodegradation of TC and OTC due to the formation of metal-ions complexes.The formation of Mg2+ complexes was unfavorable for the photodegradation of the tetracyclines at both pH values.In contrast,the Ca2+ complexes facilitated the attack of singlet oxygen (1O2) arising from self-sensitization at pH 7.3 and enhanced TC photodegradation.For the first time,selfsensitized oxidation products of TC and OTC were verified by quenching experiments and detected by LC/ESI-DAD-MS.The products had a nominal mass 14 Da higher than the parent drugs (designated M+14),which resulted from the 1O2 attack of the dimethylamino group on the C-4 atom of the tetracyclines.The presence of Ca2+ and Mg2+ also affected the generation of M+14 due to the formation of metal-ions complexes with TC and OTC.The findings suggest that the metal-ion complexation has significant impact on the selfsensitized oxidation processes and the photoproducts of tetracyclines.

Synthesis of Mg(OH)2, MgO, and Mg nanoparticles using laser ablation of magnesium in water and solvents

Energy Technology Data Exchange (ETDEWEB)

Tran, P.X.; Howard, B.H.; Martello, D.V.; Soong, Y.; Chyu, M.K.

2008-01-01

laser ablation of magnesium in deionized water (OW), solutions of OW and sodium dodecyl sulfate (50S) with different concentrations, acetone and 2-propanol has been conducted, The results showed that ablation in acetone and 2-propanol yielded MgO and Mg nanocrystallites as isolated particles and agglomerated chains probably intermixed with organic residues resulting from the alterationj decomposition of the solvents under the high-energy conditions. Brucite-like Mg(OH)2 particles were mainly produced by laser ablation of Mg in either OW or OW~SOS solutions. Ablation in OW yielded particles of fiber-like shapes having a diameter of about 5-lOnm and length as long as 150nm. Materials produced in DW-SOS solutions were composed of various size and shape particles, Some had rough surfaces with irregular shapes. Small particles were about 20-30nm and larger particles were about 120 nm. Particles with rod-like, triangular, and plate-like shapes were also observed.

Synthesis of Mg(OH) 2, MgO, and Mg nanoparticles using laser ablation of magnesium in water and solvents

Science.gov (United States)

Phuoc, Tran X.; Howard, Bret. H.; Martello, Donald V.; Soong, Yee; Chyu, Minking K.

2008-11-01

Laser ablation of magnesium in deionized water (DW), solutions of DW and sodium dodecyl sulfate (SDS) with different concentrations, acetone and 2-propanol has been conducted. The results showed that ablation in acetone and 2-propanol yielded MgO and Mg nanocrystallites as isolated particles and agglomerated chains probably intermixed with organic residues resulting from the alteration/decomposition of the solvents under the high-energy conditions. Brucite-like Mg(OH) 2 particles were mainly produced by laser ablation of Mg in either DW or DW-SDS solutions. Ablation in DW yielded particles of fiber-like shapes having a diameter of about 5-10 nm and length as long as 150 nm. Materials produced in DW-SDS solutions were composed of various size and shape particles. Some had rough surfaces with irregular shapes. Small particles were about 20-30 nm and larger particles were about 120 nm. Particles with rod-like, triangular, and plate-like shapes were also observed.

Cross-sections for the formation of isomeric pair {sup 75}Ge{sup m,g} through (n, 2n), (n, p) and (n, {alpha}) reactions measured over 13.73 MeV to 14.77 MeV and calculated from near threshold to 20 MeV neutron energies

Energy Technology Data Exchange (ETDEWEB)

Attar, F.M.D.; Dhole, S.D. [Department of Physics, University of Pune, Pune-411007 (India); Kailas, S. [Nuclear Physics Division, BARC, Mumbai-400085 (India); Bhoraskar, V.N. [Department of Physics, University of Pune, Pune-411007 (India)], E-mail: vnb@physics.unipune.ernet.in

2009-09-15

The cross-sections for formation of isomeric pair, {sup 75}Ge{sup m}({sigma}{sub m}) and {sup 75}Ge{sup g}({sigma}{sub g}), through {sup 76}Ge(n, 2n), {sup 75}As(n, p) and {sup 78}Se(n, {alpha}) reactions were measured at 13.73 MeV, 14.42 MeV and 14.77 MeV neutrons and also estimated using EMPIRE-II and TALYS codes over neutron energies from near threshold to 20 MeV. For each (n, 2n), (n, p) and (n, {alpha}) reaction, the cross-section initially increases with neutron energy, but starts decreasing as the neutron energy exceeds the respective threshold of (n, 3n), (n, pn) and (n, {alpha}n) reactions. The higher values of {sigma}{sub m} relative to {sigma}{sub g} reveal that the transitions of the excited {sup 75}Ge from higher energy levels to metastable state (7{sup +}/2) are favored as compared to unstable ground state (1{sup -}/2). The present values of cross sections for formation of {sup 75}Ge{sup m,g} through (n, 2n) and (n, {alpha}) reactions are lower, and that of (n, p) reaction are higher compared to most of the corresponding literature cross-sections.

Efeito da segregação e solubilização do MgO na morfologia de pós de ZrO2 durante a síntese pelo método Pechini Effect of MgO segregation and solubilization on the morphology of ZrO2 powders during synthesis by the Pechini's method

Directory of Open Access Journals (Sweden)

P. J. B. Marcos

2004-03-01

Full Text Available Trabalhos realizados em vários sistemas de óxidos cerâmicos têm demonstrado que a segregação dos íons durante a síntese de materiais cerâmicos pelo método Pechini tem conseqüências muito importantes tanto para a morfologia dos pós como para a sinterização. Este trabalho tem como objetivo estabelecer a influência da segregação/solubilização do MgO na morfologia e na sinterização de pós à base de ZrO2. O estudo foi realizado em pós preparados por síntese química derivada do método Pechini a 500 °C por 15 h. Observa-se que para concentrações de MgO até o limite de solubilidade no ZrO2 ocorre o crescimento de partículas e uma diminuição da área de superfície específica por causa da solubilização e do aumento do coeficiente de difusão pela geração de vacâncias de oxigênio. Contudo, após o limite de solubilidade, ocorre um aumento gradual da área de superfície específica devido à segregação dos íons na superfície dos pós e à diminuição da energia de superfície. Concentrações de MgO até 60 % molar foram utilizadas e áreas de superfície específica tão elevadas quanto 120 m²/g foram obtidas, mas as fases cristalinas formadas foram exclusivamente da zircônia solução sólida sem a presença de fases cristalinas de MgO.Studies carried out in several ceramic oxide systems have shown that segregation of ions during synthesis of ceramic materials by the Pechini's method has important morphology consequences for the powder. The aim of this paper is to establish the influence of the MgO segregation/solubilization on the morphology of ZrO2 powders. The study was performed in powders prepared by chemical synthesis derived from the Pechini's method at 500 ºC for 15 h. It is observed that MgO concentrations up to the solubility limit promote ZrO2 particle coarsening and a reduction of specific surface area by increasing the diffusion coefficient. However, MgO amounts higher than the solubility

Analysis of (Ba,Ca,Sr)3MgSi2O8:Eu2+, Mn2+ phosphors for application in solid state lighting

International Nuclear Information System (INIS)

Han, J.K.; Piqutte, A.; Hannah, M.E.; Hirata, G.A.; Talbot, J.B.; Mishra, K.C.; McKittrick, J.

2014-01-01

The luminescence properties of Eu 2+ and Mn 2+ co-activated (Ba,Ca,Sr) 3 MgSi 2 O 8 phosphors prepared by combustion synthesis were studied. Eu 2+ -activated (Ba,Ca,Sr) 3 MgSi 2 O 8 has a broad blue emission band centered at 450–485 nm and Eu 2+ –Mn 2+ -activated (Ba,Ca,Sr) 3 MgSi 2 O 8 exhibits a red emission around 620–703 nm, depending on the relative concentrations of Ba, Ca and Sr. The particle size of Eu 2+ and Mn 2+ co-activated (Ba,Ca) 3 MgSi 2 O 8 ranges from 300 nm to 1 μm depending on the metal ion and are agglomerated due to post-synthesis, high temperature annealing. The green emission of Ba 3 MgSi 2 O 8 originates from secondary phases (Ba 2 SiO 4 and BaMgSiO 4 ) confirmed by emission spectra and X-ray diffraction patterns. The secondary phases of Ba 3 MgSi 2 O 8 are removed by the addition of Sr. The quantum efficiencies range from 45% to 70% under 400 nm excitation and the lifetime of red emission of Ba 3 MgSi 2 O 8 decreases significantly with increasing temperature, which is 54% at 400 K of that at 80 K compared to that of blue emission (90% at 400 K of that at 80 K). -- highlights: • (Ba,Ca,Sr) 3 MgSi 2 O 8 :Eu 2+ , Mn 2+ phosphors were prepared by a combustion synthesis method. • The emission spectra consist of broad blue-emission band and red-emission band. • The quantum efficiencies range between 45% and 70%, depending on the relative concentrations of Ba, Ca and Sr. • The secondary phases were eliminated by additions of Sr. • Lifetime of the red-emission decreases with increasing temperature, suggesting that these phosphors are not useful for solid state lighting applications

Improved hydrogen storage properties of MgH2 catalyzed with TiO2

Science.gov (United States)

Jangir, Mukesh; Meena, Priyanka; Jain, I. P.

2018-05-01

In order to improve the hydrogenation properties of the MgH2, various concentration of rutile Titanium Oxide (TiO2) (X wt%= 5, 10, 15 wt %) is added to MgH2 by ball milling and the catalytic effect of TiO2 on hydriding/dehydriding properties of MgH2 has been investigated. Result shows that the TiO2 significantly reduced onset temperature of desorption. Onset temperature as low as 190 °C were observed for the MgH2-15 wt% TiO2 sample which is 60 °C and 160 °C lower than the as-milled and as-received MgH2. Fromm the Kissinger plot the activation energy of 15 wt% TiO2 added sample is calculated to be -75.48 KJ/mol. These results indicate that the hydrogenation properties of MgH2-TiO2 have been improved compared to the as-milled and as-received MgH2. Furthermore, XRD and XPS were performed to characterize the structural evolution upon milling and dehydrogenation.

Validation of an analytical method applicable to study of 1 mg/mL oral Risperidone solution stability

International Nuclear Information System (INIS)

Abreu Alvarez, Maikel; Garcia Penna, Caridad Margarita; Martinez Miranda, Lissette

2010-01-01

A validated analytical method by high-performance liquid chromatography (HPLC) was applicable to study of 1 mg/mL Risperidone oral solution stability. The above method was linear, accurate, specific and exact. A stability study of the 1 mg/mL Risperidone oral solution was developed determining its expiry date. The shelf life study was conducted for 24 months at room temperature; whereas the accelerated stability study was conducted with product under influence of humidity and temperature; analysis was made during 3 months. Formula fulfilled the quality specifications described in Pharmacopeia. The results of stability according to shelf life after 24 months showed that the product maintains the parameters determining its quality during this time and in accelerated studies there was not significant degradation (p> 0.05) in the product. Under mentioned conditions expiry date was of 2 years

Revisiting Mg–Mg2Ni System from Electronic Perspective

Directory of Open Access Journals (Sweden)

Zhao Qian

2017-11-01

Full Text Available Both Mg and Mg2Ni are promising electrode materials in conversion-type secondary batteries. Earlier studies have shown their single-phase prospects in electro-devices, while in this work, we have quantitatively reported the electronic properties of their dual-phase materials, that is, Mg–Mg2Ni alloys, and analyzed the underlying reasons behind the property changes of materials. The hypoeutectic Mg–Mg2Ni alloys are found to be evidently more conductive than the hypereutectic Mg–Mg2Ni system. The density functional theory (DFT calculations give the intrinsic origin of electronic structures of both Mg2Ni and Mg. The morphology of quasi-nanoscale eutectics is another factor that can affect the electronic properties of the investigated alloy system; that is, the electrical property change of the investigated alloys system is due to a combination of the intrinsic property difference between the two constituting phases and the change of eutectic microstructures that affect electron scattering. In addition, regarding the Mg–Mg2Ni alloy design for device applications, the electronic property and mechanical aspect should be well balanced.

Photoluminescence of Mg_2Si films fabricated by magnetron sputtering

International Nuclear Information System (INIS)

Liao, Yang-Fang; Xie, Quan; Xiao, Qing-Quan; Chen, Qian; Fan, Meng-Hui; Xie, Jing; Huang, Jin; Zhang, Jin-Min; Ma, Rui; Wang, Shan-Lan; Wu, Hong-Xian; Fang, Di

2017-01-01

Highlights: • High quality Mg_2Si films were grown on Si (111) and glass substrates with magnetron sputtering, respectively. • The first observation of Photoluminescence (PL) of Mg_2Si films was reported. • The Mg_2Si PL emission wavelengths are almost independence on temperature in the range of 77–300 K. • The strongest PL emissions may be attributed to interstitial Mg donor level to valence band transitions. • The activation energy of Mg_2Si is determined from the quenching of major luminescence peaks. - Abstract: To understand the photoluminescence mechanisms and optimize the design of Mg_2Si-based light-emitting devices, Mg_2Si films were fabricated on silicon (111) and glass substrates by magnetron sputtering technique, and the influences of different substrates on the photoelectric properties of Mg_2Si films were investigated systematically. The crystal structure, cross-sectional morphology, composition ratios and temperature-dependent photoluminescence (PL) of the Mg_2Si films were examined using X-ray diffraction (XRD), Scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS) and PL measurement system, respectively. XRD results indicate that the Mg_2Si film on Si (111) displays polycrystalline structure, whereas Mg_2Si film on glass substrate is of like-monocrystalline structure.SEM results show that Mg_2Si film on glass substrate is very compact with a typical dense columnar structure, and the film on Si substrate represents slight delamination phenomenon. EDS results suggest that the stoichiometry of Mg and Si is approximately 2:1. Photoluminescence (PL) of Mg_2Si films was observed for the first time. The PL emission wavelengths of Mg_2Si are almost independence on temperature in the range of 77–300 K. The PL intensity decreases gradually with increasing temperature. The PL intensity of Mg_2Si films on glass substrate is much larger than that of Mg_2Si film on Si (111) substrate. The activation energy of 18 meV is

Nanostructure characterization of Ni and B layers as artificial pinning centers in multilayered MgB2/Ni and MgB2/B superconducting thin films

International Nuclear Information System (INIS)

Sosiati, H.; Hata, S.; Doi, T.; Matsumoto, A.; Kitaguchi, H.; Nakashima, H.

2013-01-01

Highlights: ► Nanostructure characterization of Ni and B layers as artificial pinning centers (APCs). ► Relationship between nanostructure and J c property. ► Enhanced J c in parallel field by parallel APCs within the MgB 2 film. -- Abstract: Research on the MgB 2 /Ni and MgB 2 /B multilayer films fabricated by an electron beam (EB) evaporation technique have been extensively carried out. The critical current density, J c of MgB 2 /Ni and MgB 2 /B multilayer films in parallel fields has been suggested to be higher than that of monolayer MgB 2 film due to introducing the artificial pinning centers of nano-sized Ni and B layers. Nanostructure characterization of the artificial pinning centers in the multilayer films were examined by transmission electron microscopy (TEM) and scanning TEM (STEM-energy dispersive X-ray spectroscopy (STEM-EDS))–EDS to understand the mechanism of flux pinning. The growth of columnar MgB 2 grains along the film-thickness direction was recognized in the MgB 2 /Ni multilayer film, but not in the MgB 2 /B multilayer film. Nano-sized Ni layers were present as crystalline epitaxial layers which is interpreted that Ni atoms might be incorporated into the MgB 2 lattice to form (Mg,Ni)B 2 phase. On the other hand, nano-sized B layers were amorphous layers. Crystalline (Mg,Ni)B 2 layers worked more effectively than amorphous B-layers, providing higher flux-pinning force that resulted in higher J c of the MgB 2 /Ni multilayer film than the MgB 2 /B multilayer film

The transient M/G/1/0 queue: some bounds and approximations for light traffic with application to reliability

Directory of Open Access Journals (Sweden)

J. Ben Atkinson

1995-01-01

Full Text Available We consider the transient analysis of the M/G/1/0 queue, for which Pn(t denotes the probability that there are no customers in the system at time t, given that there are n(n=0,1 customers in the system at time 0. The analysis, which is based upon coupling theory, leads to simple bounds on Pn(t for the M/G/1/0 and M/PH/1/0 queues and improved bounds for the special case M/Er/1/0. Numerical results are presented for various values of the mean arrival rate λ to demonstrate the increasing accuracy of approximations based upon the above bounds in light traffic, i.e., as λ→0. An important area of application for the M/G/1/0 queue is as a reliability model for a single repairable component. Since most practical reliability problems have λ values that are small relative to the mean service rate, the approximations are potentially useful in that context. A duality relation between the M/G/1/0 and GI/M/1/0 queues is also described.

Fabrication of Polycrystalline Transparent Co+2: MgAl2O4 by a Combination of Spark Plasma Sintering (SPS and Hot Isostatic Pressing (HIP Processes

Directory of Open Access Journals (Sweden)

Sokol Maxim

2017-01-01

Full Text Available Transparent Co2+ doped MgAl2Ob4 spinel was fabricated by SPS consolidation followed by and HIP treatment. It was established that HIP treatment significantly improved transparency of the ceramic in a wide range of wavelengths, especially, in a range, which is relevant for Q-switching. Nonlinear absorption was demonstrated and the ground and excited state absorption cross sections were estimated. The positive effect of the HIP treatment on the optical properties is related to an elimination of extremely fine porosity and to the location of Co ions at Mg2+sites in the spinel ionic structure. The experimental results indicate that the fabricated specimens can be used as a passive laser Q-switching material.

Pseudopotential approach to superconductivity in MgB2

International Nuclear Information System (INIS)

Sharma, K.S.; Bhargava, Nidhi; Jain, Ritu; Goyal, Varsha; Sharma, Ritu; Sharma, Smita

2010-01-01

Superconductivity in MgB 2 has been re-examined in BCS-Eliashberg framework by employing Mc-Millan's T c -equation and form factors of MgB 2 computed from the form factors of component metals (Model-I). The empty core model pseudopotential due to Ashcroft and random phase approximation form of dielectric screening due to Gellmann and Brueckner are used in the present work. An excellent agreement between the present values and other theoretically computed values of T c and with the relevant experimental data for MgB 2 confirms the validity of the present approach. The explicit dependence of λ and T c on the isotopic masses of Mg and B, as revealed from the present work, confirms the role of lattice vibrations in the superconducting behaviour of MgB 2 and the high value of T c in it may be attributed to the phonon mediated e-e interaction coupled with higher values of phonon frequencies due to light mass of B atoms. It has also been observed that the pseudo-atom model (Model-II) with appropriate choice of the potential parameter r c successfully explains high value of T c and isotope effect in MgB 2 , confirming the prominent role played by electron-phonon interaction in the high-T c superconductivity observed in MgB 2 . The isotope effect exponent α-values obtained from the two models are in complete agreement with each other and the present value α = 0.46 is also much closer to the BCS value of 0.5. Interaction strength N 0 V values obtained from the two models are also in perfect agreement with each other and the present value N 0 V = 0.48 suggests that MgB 2 is a strong coupling superconductor. (author)

Single-crystalline MgAl2O4 spinel nanotubes using a reactive and removable MgO nanowire template

International Nuclear Information System (INIS)

Fan Hongjin; Knez, Mato; Scholz, Roland; Nielsch, Kornelius; Pippel, Eckhard; Hesse, Dietrich; Goesele, Ulrich; Zacharias, Margit

2006-01-01

Using MgO nanowires as a reactive template, we fabricated for the first time single-crystal MgAl 2 O 4 spinel nanotubes through an interfacial solid-state reaction of MgO-Al 2 O 3 core-shell nanowires. Single-crystal MgO nanowires are coated with a conformal thin layer of amorphous Al 2 O 3 via atomic layer deposition. Subsequent annealing at 700 deg. C activates the interfacial reaction between MgO and Al 2 O 3 , transforming the alumina shell into a spinel shell. Finally, after etching away the remaining MgO core in ammonia sulfuric solution, MgAl 2 O 4 spinel nanotubes are obtained. As a transition from conventional planar spinel layers via thin-film interface reactions, our result might open a window for the fabrication of a wide variety of MgO-based spinel one-dimensional nanostructures

Dehydriding reaction of Mg(NH2)2-LiH system under hydrogen pressure

International Nuclear Information System (INIS)

Aoki, M.; Noritake, T.; Kitahara, G.; Nakamori, Y.; Towata, S.; Orimo, S.

2007-01-01

The dehydriding and structural properties of the 3Mg(NH 2 ) 2 + 12LiH system under hydrogen pressure were investigated using the pressure-composition (p-c) isotherm measurement and X-ray diffraction (XRD) analysis. Two distinct regions, a plateau region and a sloping region, can be seen on the p-c isotherms and the amount of the desorbed hydrogen at 523 K was 4.9 mass%. The enthalpy of hydrogenation calculated using a van't Hoff plot was -46 kJ/mol H 2 . The dehydriding reaction was proposed for the 3Mg(NH 2 ) 2 + 12LiH system based on the obtained p-c isotherms and XRD profiles and chemical valences of Li, Mg, N, and H. In the plateau region on the p-c isotherm, Mg(NH 2 ) 2 , Li 4 Mg 3 (NH 2 ) 2 (NH) 4 (tetragonal), and LiH phases coexist and the molar ratio of the Li 4 Mg 3 (NH 2 ) 2 (NH) 4 phase increases (while those of Mg(NH 2 ) 2 and LiH phases decrease) with the amount of the desorbed hydrogen. On the other hand, the mixture of Li 4+x Mg 3 (NH 2 ) 2-x (NH) 4+x + (8-x)LiH (0 ≤ x ≤ 2) is formed and the lattice volume of the Li 4+x Mg 3 (NH 2 ) 2-x (NH) 4+x phase continuously increases with the amount of the desorbed hydrogen in the sloping region on the p-c isotherm

Synthesis and crystal structure of Mg0.5NbO2: An ion-exchange reaction with Mg2+ between trigonal [NbO2]- layers

Science.gov (United States)

Miura, Akira; Takei, Takahiro; Kumada, Nobuhiro

2013-01-01

A new layered niobate, Mg0.5NbO2, was synthesized from LiNbO2 through a cation-exchange reaction with Mg2+ at 450-550 °C. This is the first example of a topotactic reaction with an aliovalent cation between trigonal [NbO2]- layers. It is proposed to be isostructural with LiNbO2 (space group; P63/mmc) with lattice parameters of a=2.9052(6) Å, c=10.625(15) Å. The lattice parameters and formation energy of Mg0.5NbO2 crystallized in LiNbO2 form and other layered CaNb2O4 one were calculated by density functional theory.

Synthesize and electrochemical characterization of Mg-doped Li-rich layered Li[Li0.2Ni0.2Mn0.6]O2 cathode material

International Nuclear Information System (INIS)

Wang, Dan; Huang, Yan; Huo, Zhenqing; Chen, Li

2013-01-01

Highlights: • Layered Li[Li 0.2 Ni 0.2−x Mn 0.6−x Mg 2x ]O 2 (2x = 0, 0.01, 0.02, 0.05) were synthetized. • Li[Li 0.2 Ni 0.2−x Mn 0.6−x Mg 2x ]O 2 exhibit enhanced electrochemical properties. • The improved performance is attributed to enhanced structure stability. -- Abstract: Mg-doped Li[Li 0.2 Ni 0.2 Mn 0.6 ]O 2 as a Li-rich cathode material of lithium-ion batteries were prepared by co-precipitation method and ball-milling treatment using Mg(OH) 2 as a dopant. Scanning electron microscopy (SEM), ex situ X-ray powder diffraction (XRD), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvantatic charge/discharge were used to investigate the effect of Mg doping on structure and electrochemical performance. Compared with the bare material, Mg-doped materials exhibit better cycle stabilities and superior rate capabilities. Li[Li 0.2 Ni 0.195 Mn 0.595 Mg 0.01 ]O 2 displays a high reversible capacity of 226.5 mAh g −1 after 60 cycles at 0.1 C. The excellent cycle performance can be attributed to the improvement in structure stability, which is verified by XRD tests before and after 60 cycles. EIS results show that Mg doping decreases the charge-transfer resistance and enhances the reaction kinetics, which is considered to be the major factor for higher rate performance

Hydrogen storage and hydrolysis properties of core-shell structured Mg-MFx (M=V, Ni, La and Ce) nano-composites prepared by arc plasma method

Science.gov (United States)

Mao, Jianfeng; Zou, Jianxin; Lu, Chong; Zeng, Xiaoqin; Ding, Wenjiang

2017-10-01

In this work, core-shell structured Mg-MFx (M = V, Ni, La and Ce) nano-composites are prepared by using arc plasma method. The particle size distribution, phase components, microstructures, hydrogen sorption properties of these composites and hydrolysis properties of their corresponding hydrogenated powders are carefully investigated. It is shown that the addition of MFx through arc plasma method can improve both the hydrogen absorption kinetics of Mg and the hydrolysis properties of corresponding hydrogenated powders. Among them, the Mg-NiF2 composite shows the best hydrogen absorption properties at relatively low temperatures, which can absorb 3.26 wt% of H2 at 373 K in 2 h. Such rapid hydrogen absorption rate is mainly due to the formation of Mg2Ni and MgF2 on Mg particles during arc evaporation and condensation. In contrast, measurements also show that the hydrogenated Mg-VF3 composite has the lowest peak desorption temperature and the fastest hydrolysis rate among all the hydrogenated Mg-MFx composites. The less agglomeration tendency of Mg particles and VO2 covered on MgH2 particles account for the reduced hydrogen desorption temperature and enhanced hydrolysis rate.

Influence of elemental diffusion on low temperature formation of MgH2 in TiMn1.3T0.2-Mg (T = 3d-transition elements)

International Nuclear Information System (INIS)

Yamamoto, K.; Tanioka, S.; Tsushio, Y.; Shimizu, T.; Morishita, T.; Orimo, S.; Fujii, H.

1996-01-01

In order to examine the influence of the elemental diffusion from the host compound into the Mg region on low temperature formation of MgH 2 , we have investigated the hydriding properties and the microstructures of the composite materials TiMn 1.3 T 0.2 -Mg (T = V, Cr, Mn, Fe, Co, Ni and Cu). MgH 2 is formed at 353 K in all composite materials. Of all the substitutions, the amount of MgH 2 is the largest in the case of the Cu substitution, which originates from the existence of the Mg-Mg 2 Cu eutectic formed by Cu diffusion from the host compound TiMn 1.3 Cu 0.2 into the Mg region during the liquid phase sintering. In addition, the hydrogen capacity of TiMn 1.3 Cu 0.2 -Mg (that is TiMn 1.3 Cu 0.1 -(Mg+Mg 2 Cu) after the sintering) easily saturates in comparison with TiMn 1.5 -(Mg+Mg 2 Cu) without Cu diffusion. It is concluded that Cu diffusion promotes the mobility of hydrogen atoms at the complex interface between the host compound and the Mg region. (orig.)

MgAl_2O_4 foams obtained by combustion synthesis

International Nuclear Information System (INIS)

Moraes, G.G.; Rosa, M.A.; Kronbauer, D.P.; Pozzobom, I.F.; Fernandes, C.P.; Oliveira, A.P. Novaes de

2014-01-01

This work aims to study magnesium aluminate (MgAl_2O_4) ceramic foams obtained by combustion synthesis in solution without the need of surfactants to stabilize bubbles. The precursors, Al(NO_3)_3_.9H_2O and Mg(NO_3)_2_.6H_2_O, dispersed in distilled water (20 wt%) were magnetically stirred under heating (70°C). At the beginning of the reaction, a fuel composed by a mixture of residual glycerins from the production of biodiesel was added. The foams were produced by controlling the stirring speed and temperature. The applied thermal cycle to consolidate the foams consisted of heating at 1°C/min to 600°C/120 min and subsequently raising the temperature at 10°C/min to 1600°C/120 min. The obtained materials were characterized by SEM,TEM and from tomographic images. The results showed that the obtained magnesium aluminate foams have a high porosity (97%), a high connectivity and pore sizes (diameters) between 30 and 1200 μm. (author)

The use of one-dimensional Niobate to improve MgH{sub 2} hydrogen sorption

Energy Technology Data Exchange (ETDEWEB)

Brum, M.C., E-mail: mbrum@metalmat.ufrj.br; Conceição, M.O.T. da; Jardim, P.M.; Santos, D.S. dos

2014-12-05

Highlights: • The 1-D Niobate W and Niobate C catalysts were synthesized. • The composites MgH{sub 2} + 5 wt.% catalysts were obtained by 20 min of mechanical milling. • The synthesized wired-like material 1-D Niobate W showed to be a promising catalyst. • A desorption capacity of 6.0 wt.%. of H{sub 2} was attained in 10 min with MgH{sub 2} + 5 wt.% 1-D Niobate W. - Abstract: A study was performed on the hydrogen absorption/desorption properties of MgH{sub 2} with the addition of Niobates synthesized by hydrothermal treatment of Nb{sub 2}O{sub 5} in 10 M NaOH. Scanning Electron Microscopy (SEM) and X-ray diffraction (XRD) were used to evaluate their synthesis and show the morphological and crystallographic differences between Nb{sub 2}O{sub 5} used as a precursor and the Niobates produced, the one-dimensional wired type, 1-D Niobate W and the cuboid one, Niobate C. The ball milling of MgH{sub 2} with the Niobates was performed within only 20 min and afterwards the Differential Scanning Calorimetry (DSC) examination of MgH{sub 2} + 1-D Niobate W and MgH{sub 2} + Niobate C showed the shifting of the peaks for both composites in comparison to pure MgH{sub 2}. The influence of the two different types of Niobates and also the Nb{sub 2}O{sub 5} on the hydrogen absorption/desorption capacity was evaluated at 350 °C. The higher absorption and desorption values were attained by the MgH{sub 2} + 5 wt.% 1-D Niobate W composite, reaching, in 10 min, approximately 5.0 wt.% and 6.0 wt.%, respectively. The possible mechanism involved in such property improvement upon adding niobium based catalysts with different morphology and structure was discussed.

Prussian Blue Mg-Li Hybrid Batteries.

Science.gov (United States)

Sun, Xiaoqi; Duffort, Victor; Nazar, Linda F

2016-08-01

The major advantage of Mg batteries relies on their promise of employing an Mg metal negative electrode, which offers much higher energy density compared to graphitic carbon. However, the strong coulombic interaction of Mg 2+ ions with anions leads to their sluggish diffusion in the solid state, which along with a high desolvation energy, hinders the development of positive electrode materials. To circumvent this limitation, Mg metal negative electrodes can be used in hybrid systems by coupling an Li + insertion cathode through a dual salt electrolyte. Two "high voltage" Prussian blue analogues (average 2.3 V vs Mg/Mg 2+ ; 3.0 V vs Li/Li + ) are investigated as cathode materials and the influence of structural water is shown. Their electrochemical profiles, presenting two voltage plateaus, are explained based on the two unique Fe bonding environments. Structural water has a beneficial impact on the cell voltage. Capacities of 125 mAh g -1 are obtained at a current density of 10 mA g -1 (≈C/10), while stable performance up to 300 cycles is demonstrated at 200 mA g -1 (≈2C). The hybrid cell design is a step toward building a safe and high density energy storage system.

Structure and electrochemical properties of Mg2SnO4 nanoparticles synthesized by a facile co-precipitation method

International Nuclear Information System (INIS)

Tang, Hao; Cheng, Cuixia; Yu, Gaige; Liu, Haowen; Chen, Weiqing

2015-01-01

Nanosized Mg 2 SnO 4 has been synthesized by a facile co-precipitation method. The structure and morphology of the as-prepared samples are characterized by X-ray diffraction (XRD), X-ray photoelectron spectrometer (XPS), fourier Transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). It is found that Mg 2 SnO 4 sample is very sensitive to the aging time of the precursor. The single phase Mg 2 SnO 4 nanoparticles with ∼23 nm can be obtained at 900 °C using the aging 35 min percusor as source. The electrochemical properties of the powder obtained at 900 °C are investigated by galvanostatic discharge-charge tests and cyclic voltammograms (CVs). The initial specific discharge capacity reaches as high as 927.7 mAh g −1 at 0.2 mA cm −2 in 0.05–3.0 V, which indicates that Mg 2 SnO 4 nanoparticles could be a promising candidate of anode material for Li-ion batteries. - Highlights: • Nanosized Mg 2 SnO 4 has been synthesized by a facile co-precipitation method. • We find that Mg 2 SnO 4 sample is very sensitive to the ageing time of the precursor. • The single phase Mg 2 SnO 4 nanoparticles with about 23 nm can be obtained by calcining the ageing 35 min percusor at 900 °C. • The obtained powders show a better electrochemical performance

Raman-spectroscopic (Fe/Fe+Mg, CO2) and Structural studies of Mg-Fe cordierites

International Nuclear Information System (INIS)

Haefeker, U.

2013-01-01

In the course of this dissertation synthetic hexagonal and orthorhombic Mg-Fe-cordierites have been investigated with Raman-spectroscopy and XRD methods. Cordierite´s Mg- and Fe-end-members as well as their Mg-Fe solid solutions with the chemical formula (Mg, Fe 2+ ) 2 Al 4 Si 5 O 18 *nH 2 O have been synthesized. Raman-data of synthetic hydrous Mg- and Fe-cordierites have been obtained in the wavenumber-region 100-1250 cm-1 and the experimental data were then compared with the results of quantum-mechanical calculations. 86 theoretical bands could be related to specific vibrational modes of the tetrahedral and octahedral sites of the cordierite structure. Maximum and mean deviation between experimentally-derived bands and calculated modes were ±7 cm -1 for Mg-cordierite and ±19 cm -1 for Fe-cordierite. Spectra comparison revealed a trend of peak downshifting as a consequence of Fe-incorporation. The calculations now allow more accurate interpretation of the Raman spectra with respect to structural changes of cordierite, resulting from Al-Si ordering and Mg-Fe exchange. Atomic motions in cordierite have been compared with those of the structurally similar mineral beryl. Investigations of 16 H 2 O-bearing synthetic well-ordered Mg-Fe-cordierites (XFe =0-1) with micro-Raman spectroscopy revealed a linear correlation between the Fe/Mg ratio and the position of certain Raman peaks. The peaks (wave-number Mg-/Fe-cordierite) at 122/111, 262/257, 430/418, 579/571, 974/967, and 1012/1007 cm -1 were selected for a detailed deconvolution analysis . The shifts of these peaks were then plotted vs. XFe and regression of the data lead to the formulation of a set of linear equations. In addition, the effect of different H 2 O contents and the degree of Al-Si ordering on the Fe/Mg determination were also investigated. Testing the calibration against data from six well-characterized natural cordierite samples yielded excellent agreement. Existing calibration diagrams for CO 2

Influence of a transition metal atom on the geometry and electronic structure of Mg and Mg-H clusters

International Nuclear Information System (INIS)

Siretskiy, M.Yu.; Shelyapina, M.G.; Fruchart, D.; Miraglia, S.; Skryabina, N.E.

2009-01-01

We report on the study of (MgH 2 ) n + M complexes (M = Ti or Ni) carried out within the framework of the cluster density functional theory (DFT) method. The influence of such transition metal atoms on the cluster geometry and electronic structure is discussed considering the stability of MgH 2 hydride.

Dry cryomagnetic system with MgB2 coil

Science.gov (United States)

Abin, D. A.; Mineev, N. A.; Osipov, M. A.; Pokrovskii, S. V.; Rudnev, I. A.

2017-12-01

MgB2 may be the future superconducting wire material for industrial magnets due to it’s higher operation temperature and potentially lower cost than low temperature superconductors (LTS) have. We designed a compact cryomagnetic system with the use of MgB2. The possibility of creating a magnet with a central field of 5 T from a commercial MgB2 wire by the “react and wound” method was investigated. The magnetic system is cooled by a cryocooler through a copper bus. The magnet has a warm bore diameter of 4 cm. The design of a magnet consisting of three concentric solenoids is proposed: an internal one of high-temperature superconductor (HTS), an average of MgB2, and an external of NbTi. The operating current of the system is 100 A. Two pairs of current leads are used. A separate pair of current leads for power supplying NbTi coil allows testing of MgB2 and HTS coils in an external field. The load curves for each of the magnets are calculated.

The influence of Ni addition and hot-extrusion on the microstructure and tensile properties of Al–15%Mg2Si composite

International Nuclear Information System (INIS)

Emamy, M.; Khodadadi, M.; Honarbakhsh Raouf, A.; Nasiri, N.

2013-01-01

Highlights: ► Ni content on the microstructure and tensile properties of Al–Mg 2 Si composite. ► Ni changed the size of primary Mg 2 Si from 42 μm to 17 μm. ► Higher UTS and elongation values obtained by addition of 5 wt% Ni. ► Fracture behavior changed from brittle to ductile by Ni addition and extrusion. - Abstract: The effects of nickel addition and hot-extrusion on the microstructure and tensile properties of in situ Al–15%Mg 2 Si composite specimens have been investigated. Al–15%Mg 2 Si composite ingots were prepared by an in situ process and different amounts of nickel (0.1, 0.3, 0.5, 1.0, 3.0 and 5.0 wt% Ni) were added to the remelted composite. Optical microscopy (OM) and scanning electron microscopy (SEM) indicated that Ni addition changes the morphology of both primary and eutectic Mg 2 Si phases and decreases the size of primary Mg 2 Si particles from 42 μm to 17 μm. Hot-extrusion was found to be powerful in breaking the eutectic network and changing the size and morphology of pseudo-eutectic Mg 2 Si phase. The results obtained from tensile testing revealed that both Ni addition and hot-extrusion process improve ultimate tensile strength (UTS) and elongation values. Fracture surface examinations revealed a transition from brittle fracture mode in as-cast composite to ductile fracture in hot-extruded composite after Ni addition. This can be attributed to the changes in size and morphology of primary and eutectic Mg 2 Si phases and also the formation of more and finer α-Al phase

Investigations on FCAM-III (Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36): A new homologue of the aenigmatite structure-type in the system CaO-MgO-Fe2O3-Al2O3

Science.gov (United States)

Zöll, Klaus; Kahlenberg, Volker; Krüger, Hannes; Tropper, Peter

2018-02-01

In the course of a systematic study of a part of the quaternary system Fe2O3-CaO-Al2O3-MgO (FCAM) the previously unknown compound Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36 (FCAM-III) has been synthesized. By analogy with the so-called SFCA series [1-5], our investigation in the system of FCAM shows the existence of a stoichiometric homologous series M14+6nO20+8n, where M = Fe, Ca, Al, Mg and n = 1 or 2. In air, we can prove the formation of coexisting FCAM-III and FCAM-I solid solutions at 1400 °C. By increasing the temperature up to 1425 °C FCAM-I disappears completely and FCAM-III co-exists with magnesiumferrite and a variety of calcium iron oxides. At 1450 °C FCAM-III breaks down to a mixture of FCAM-I again as well as magnesioferrite and melt. Small single-crystals of FCAM-III up to 35 μm in size could be retrieved from the 1425 °C experiment and were subsequently characterized using electron microprobe analysis and synchroton X-ray single-crystal diffraction. Finally the Fe2+/Fetot ratio was calculated from the total iron content based on the crystal-chemical formula obtained from EMPA measurements and charge balance considerations. FCAM-III or Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36 has a triclinic crystal structure (space group P 1 ̅). The basic crystallographic data are: a = 10.223(22) Å, b = 10.316(21) Å, c = 14.203(15) Å, α = 93.473(50)°, β = 107.418(67)°, γ = 109.646(60)°, V = 1323.85(2) ų, Z = 1. Using Schreinemaker's technique to analyze the phase relations in the system Fe2O3-CaO-Al2O3-MgO it was possible to obtain the semi-quantitative stability relations between the participating phases and construct a topologically correct phase sequence as a function of T and fO2. The analysis shows that Ca2Al0.5Fe1.5O5 (C2A0.25F0.75) and CaAl1.5Fe2.5O7 (CA0.75F1.25) with higher calculated Fe2+ contents are preferably formed at lower oxygen fugacity and react to CaAl0.5Fe1.5O4 (CA0.25F0.75) by increasing fO2. Spinel-type magnesium

Formation, stability and structural characterization of ternary MgUO{sub 2}(CO{sub 3}){sub 3}{sup 2-} and Mg{sub 2}UO{sub 2}(CO{sub 3}){sub 3}(aq) complexes

Energy Technology Data Exchange (ETDEWEB)

Lee, Jun-Yeop; Yun, Jong-Il [KAIST, Daejeon (Korea, Republic of). Dept. of Nuclear and Quantum Engineering; Vespa, Marika; Gaona, Xavier; Dardenne, Kathy; Rothe, Joerg; Rabung, Thomas; Altmaier, Marcus [Karlsruhe Institute of Technology, Karlsruhe (Germany). Inst. for Nuclear Waste Disposal

2017-06-01

The formation of ternary Mg-UO{sub 2}-CO{sub 3} complexes under weakly alkaline pH conditions was investigated by time-resolved laser fluorescence spectroscopy (TRLFS) and extended X-ray absorption fine structure (EXAFS) and compared to Ca-UO{sub 2}-CO{sub 3} complexes. The presence of two different Mg-UO{sub 2}-C{sub 3} complexes was identified by means of two distinct fluorescence lifetimes of 17±2 ns and 51±2 ns derived from the multi-exponential decay of the fluorescence signal. Slope analysis in terms of fluorescence intensity coupled with fluorescence intensity factor as a function of log [Mg(II)] was conducted for the identification of the Mg-UO{sub 2}-CO{sub 3} complexes forming. For the first time, the formation of both MgUO{sub 2}(CO{sub 3}){sub 3}{sup 2-} and Mg{sub 2}UO{sub 2}(CO{sub 3}){sub 3}(aq) species was confirmed and the corresponding equilibrium constants were determined as log β {sub 113}=25.8±0.3 and β {sub 213}=27.1±0.6, respectively. Complementarily, fundamental structural information for both Ca-UO{sub 2}-CO{sub 3} and Mg-UO{sub 2}-CO{sub 3} complexes was gained by extended EXAFS revealing very similar structures between these two species, except for the clearly shorter U-Mg distance (3.83 Aa) compared with U-Ca distance (4.15 Aa). These results confirmed the inner-sphere character of the Ca/Mg-UO{sub 2}-CO{sub 3} complexes. The formation constants determined for MgUO{sub 2}(CO{sub 3}){sub 3}{sup 2-} and Mg{sub 2}UO{sub 2}(CO{sub 3}){sub 3}(aq) species indicate that ternary Mg-UO{sub 2}-CO{sub 3} complexes contribute to the relevant uranium species in carbonate saturated solutions under neutral to weakly alkaline pH conditions in the presence of Mg(II) ions, which will induce notable influences on the U(VI) chemical species under seawater conditions.

Efficacy and tolerability of tamsulosin 0.4 mg in Asian patients with lower urinary tract symptoms secondary to benign prostatic hyperplasia refractory to tamsulosin 0.2 mg: a randomized placebo controlled trial.

Science.gov (United States)

Kim, Jung Jun; Han, Deok Hyun; Sung, Hyun Hwan; Choo, Seol Ho; Lee, Sung Won

2014-07-01

To evaluate the efficacy and safety of tamsulosin dose increase to 0.4 mg daily in Asian patients with lower urinary tract symptoms secondary to benign prostatic hyperplasia refractory to tamsulosin 0.2 mg treatment. We carried out a 12-week, single-center, randomized, placebo-controlled trial in 220 patients. Patients treated with 0.2 mg tamsulosin daily without other lower urinary tract symptoms secondary to benign prostatic hyperplasia medication for more than 3 months and refractory to this treatment were enrolled. We defined "refractory" as an International Prostate Symptom Score of 13 or greater and a maximum flow rate of 15 or under despite medication. Patients with a surgical history related to lower urinary tract symptoms secondary to benign prostatic hyperplasia or a postvoid residual of 150 mL or greater were excluded. Eligible patients were randomly assigned to the 0.4 mg group (two tablets of 0.2 mg tamsulosin once daily) or the 0.2 mg group (one tablet of 0.2 mg tamsulosin and one tablet of placebo once daily). International Prostate Symptom Score, maximum flow rate, blood pressure, heart rate, and adverse events were compared between the two groups at 4 weeks and 12 weeks. A total of 220 patients were enrolled and analyzed. There were no differences in baseline characteristics between the two groups. After 12 weeks of medication, the International Prostate Symptom Score was not different between the two groups. However, the improvement in maximum flow rate was greater in the 0.4 mg group than the 0.2 mg group (3.0 ± 0.48 mL/s vs -0.25 ± 0.30 mL/s, P Tamsulosin 0.4 mg appears to be a safe treatment regimen for treating lower urinary tract symptoms secondary to benign prostatic hyperplasia in Asian patients who do not respond to 0.2 mg treatment. Increasing the dose of tamsulosin results in a significant improvement in maximum flow rate without any increase in cardiovascular complications. © 2014 The

Thermoelectric properties and microstructure of Mg3Sb2

International Nuclear Information System (INIS)

Condron, Cathie L.; Kauzlarich, Susan M.; Gascoin, Franck; Snyder, G. Jeffrey

2006-01-01

Mg 3 Sb 2 has been prepared by direct reaction of the elements. Powder X-ray diffraction, thermal gravimetric, differential scanning calorimetery, and microprobe data were obtained on hot pressed samples. Single phase samples of Mg 3 Sb 2 were prepared and found to contain oxygen at the grain boundaries and to lose Mg and oxidize at temperatures above 900 K. Thermoelectric properties were characterized by Seebeck, electrical resistivity, and thermal conductivity measurements from 300 to 1023 K, and the maximum zT was found to be 0.21 at ∼875 K. - Graphical abstract: Dimensionless figure of merit for Mg 3 Sb 2 hot pressed and sintered at 873 K. The inset illustrates the crystal structure of Mg 3 Sb 2 along the [100] direction (white=Mg, black=Sb)

Glutathione transferase-M2-2 secreted from glioblastoma cell protects SH-SY5Y cells from aminochrome neurotoxicity.

Science.gov (United States)

Cuevas, Carlos; Huenchuguala, Sandro; Muñoz, Patricia; Villa, Monica; Paris, Irmgard; Mannervik, Bengt; Segura-Aguilar, Juan

2015-04-01

U373MG cells are able to take up aminochrome that induces glutathione transferase M2-2 (GSTM2) expression in a concentration-dependent manner where 100 µM aminochrome increases GSTM2 expression by 2.1-fold (P protects SH-SY5Y cells incubated with 10 µM aminochrome. The significant protection provided by U373MG-conditioned medium in SH-SY5Y cells incubated with aminochrome was dependent on GSTM2 internalization into SH-SY5Y cells as evidenced by (i) uptake of (14)C-GSTM2 released from U373MG cells into SH-SY5Y cells, a process inhibited by anti-GSTM2 antiserum; (ii) lack of protection of U373MG-conditioned medium in the presence of anti-GSTM2 antiserum on SH-SY5Y cells treated with aminochrome; and (iii) lack of protection of conditioned medium from U373MGsiGST6 that expresses an siRNA directed against GSTM2 on SH-SY5Y cells treated with aminochrome. In conclusion, our results demonstrated that U373MG cells protect SH-SY5Y cells against aminochrome neurotoxicity by releasing GSTM2 into the conditioned medium and subsequent internalization of GSTM2 into SH-SY5Y cells. These results suggest a new mechanism of protection of dopaminergic neurons mediated by astrocytes by releasing GSTM2 into the intersynaptic space and subsequent internalization into dopaminergic neuron in order to protect these cells against aminochrome neurotoxicity.

Intra-articular sodium hyaluronate 2 mL versus physiological saline 20 mL versus physiological saline 2 mL for painful knee osteoarthritis: a randomized clinical trial

DEFF Research Database (Denmark)

Lundsgaard, C.; Dufour, N.; Fallentin, E.

2008-01-01

, Knee Injury and Osteoarthritis Outcome Score (KOOS), Osteoarthritis Research Society International (OARSI) criteria, and global assessment of the patient's condition. Results: The mean age of the patients was 69.4 years; 55% were women. The effects of hyaluronate 2 mL, physiological saline 20 m......Objective: Methodological constraints weaken previous evidence on intra-articular viscosupplementation and physiological saline distention for osteoarthritis. We conducted a randomized, patient- and observer-blind trial to evaluate these interventions in patients with painful knee osteoarthritis....... Methods: We centrally randomized 251 patients with knee ostcoarthritis to four weekly intra-articular injections of sodium hyaluronate 2 mL (Hyalgan(R) 10.3 mg/mL) versus physiological saline 20 mL (distention) versus physiological saline 2 mL (placebo) and followed patients for 26 weeks. Inclusion...

Refinement of Mg2Si reinforcement in a commercial Al–20%Mg2Si in-situ composite with bismuth, antimony and strontium

International Nuclear Information System (INIS)

Nordin, Nur Azmah; Farahany, Saeed; Ourdjini, Ali; Abu Bakar, Tuty Asma; Hamzah, Esah

2013-01-01

Refinement by addition elements of Al–Mg 2 Si alloys is known to result in a change of primary Mg 2 Si morphology. In this paper, the effects of Bi, Sb and Sr on the characteristic parameters of Al–20%Mg 2 Si in-situ composite have been investigated by computer aided cooling curve thermal analysis and microstructural inspection. Size, density and aspect ratio measurements showed that additions of 0.4 wt.% Bi, 0.8 wt.% Sb and 0.01 wt.% Sr refined the Mg 2 Si reinforcement. Exceeding these concentrations, however, resulted in coarsening of Mg 2 Si particles with no change in the morphology. The results also showed that addition elements caused a decrease in the nucleation and growth temperatures of Mg 2 Si particles. The refining effect of Bi, Sb and Sr is likely to be related to the effect of oxide bifilms suspended in the composite melt as favored nucleation substrates for Mg 2 Si particles. - Highlight: • 0.4 wt.%, 0.8 wt.% and 0.01 wt.% is the optimum content for Bi, Sb and Sr addition. • Exceeding optimum concentration resulted in the coarsening of reinforcements. • Nucleation and growth temperatures decrease with addition of Bi, Sb and Sr. • The refining effect of Bi, Sb and Sr is likely to be related to the oxide bifilms

Behaviour of Fe4O5-Mg2Fe2O5 solid solutions and their relation to coexisting Mg-Fe silicates and oxide phases

Science.gov (United States)

Uenver-Thiele, Laura; Woodland, Alan B.; Miyajima, Nobuyoshi; Ballaran, Tiziana Boffa; Frost, Daniel J.

2018-03-01

Experiments at high pressures and temperatures were carried out (1) to investigate the crystal-chemical behaviour of Fe4O5-Mg2Fe2O5 solid solutions and (2) to explore the phase relations involving (Mg,Fe)2Fe2O5 (denoted as O5-phase) and Mg-Fe silicates. Multi-anvil experiments were performed at 11-20 GPa and 1100-1600 °C using different starting compositions including two that were Si-bearing. In Si-free experiments the O5-phase coexists with Fe2O3, hp-(Mg,Fe)Fe2O4, (Mg,Fe)3Fe4O9 or an unquenchable phase of different stoichiometry. Si-bearing experiments yielded phase assemblages consisting of the O5-phase together with olivine, wadsleyite or ringwoodite, majoritic garnet or Fe3+-bearing phase B. However, (Mg,Fe)2Fe2O5 does not incorporate Si. Electron microprobe analyses revealed that phase B incorporates significant amounts of Fe2+ and Fe3+ (at least 1.0 cations Fe per formula unit). Fe-L2,3-edge energy-loss near-edge structure spectra confirm the presence of ferric iron [Fe3+/Fetot = 0.41(4)] and indicate substitution according to the following charge-balanced exchange: [4]Si4+ + [6]Mg2+ = 2Fe3+. The ability to accommodate Fe2+ and Fe3+ makes this potential "water-storing" mineral interesting since such substitutions should enlarge its stability field. The thermodynamic properties of Mg2Fe2O5 have been refined, yielding H°1bar,298 = - 1981.5 kJ mol- 1. Solid solution is complete across the Fe4O5-Mg2Fe2O5 binary. Molar volume decreases essentially linearly with increasing Mg content, consistent with ideal mixing behaviour. The partitioning of Mg and Fe2+ with silicates indicates that (Mg,Fe)2Fe2O5 has a strong preference for Fe2+. Modelling of partitioning with olivine is consistent with the O5-phase exhibiting ideal mixing behaviour. Mg-Fe2+ partitioning between (Mg,Fe)2Fe2O5 and ringwoodite or wadsleyite is influenced by the presence of Fe3+ and OH incorporation in the silicate phases.

Synthesis and photoluminescence of Eu3+ and Mn2+ doped double phosphates KMLa(PO4)2 (M = Zn, Mg)

International Nuclear Information System (INIS)

Pan Yuexiao; Zhang Qinyuan; Jiang Zhonghong

2006-01-01

Two compounds, KMgLa(PO 4 ) 2 and KZnLa(PO 4 ) 2 doped with Eu 3+ and Mn 2+ ions, have been synthesized by a conventional solid-state method at 850 deg. C. Structures of KMgLa(PO 4 ) 2 and KZnLa(PO 4 ) 2 have been investigated and confirmed by X-ray diffraction and photoluminescence spectra. The results indicate that the compounds have remained the monoclinic structure of LaPO 4 with space group of C s when (K + , Mg 2+ ) or (K + , Zn 2+ ) could substitute half of the La 3+ ions. Under an ultraviolet source, KMgLa(PO 4 ) 2 :Mn 2+ has shown a bright red phosphorescent color, while KZnLa(PO 4 ) 2 :Mn 2+ has shown an orange-red emission which is assigned to the electronic transition of 4 T 1 ( 4 G)- 6 A 1 ( 6 S) of Mn 2+ in strong crystal field