Improved flux pinning behaviour in bulk MgB2 achieved by nano-SiO2 addition

International Nuclear Information System (INIS)

Rui, X F; Zhao, Y; Xu, Y Y; Zhang, L; Sun, X F; Wang, Y Z; Zhang, H

2004-01-01

Bulk MgB 2 with SiO 2 nanoparticles added has been synthesized using a simple solid-state reaction route. The lattice constant in the c direction increases with additive content due to a small amount of Si being doped into the lattice of the MgB 2 ; however, T c is almost fixed at 37.2 K. The addition of SiO 2 nanoparticles also improves the J c -H and H irr -T characteristics of MgB 2 when the additive content is lower than 7%. At 20 K and 1 T, J c for the sample with 7% additive content reaches 2.5 x 10 5 A cm -2 . Microstructural analysis reveals that a high density of MgSi 2 nanoparticles (10-50 nm) exists inside the MgB 2 grains, leading to the formation of a nanocomposite superconductor

Evolution of Mg-5Al-0.4Mn microstructure after rare earth elements addition

Directory of Open Access Journals (Sweden)

A. Żydek

2011-04-01

Full Text Available Mg-5Al-0.4Mn-xRE (x = 0, 1, 2, 3 wt.% magnesium alloys were prepared successfully by casting method. The microstructure wasinvestigated by light microscopy. The influence of rare earth (RE elements on the area fraction of eutectic was analysed. The obtainedresults revealed that the as-cast Mg-5Al-0.4Mn alloy consist of α - Mg matrix and eutectic α + γ (where γ is Mg17Al12. However, whilerare earth elements were added to the Mg-Al type alloy, Al11RE3 precipitates were formed. The amount of the Al11RE3 precipitatesincreased with increasing addition of RE, but the amount of γ - Mg17Al12 decreased.

Effect of MgCl2 addition on the sintering behavior of MgAl2O4 spinel and formation of nano-particles

Directory of Open Access Journals (Sweden)

Mohammadi F.

2014-01-01

Full Text Available In this paper, the effect of MgCl2 addition on the sintering behavior of MgAl2O4 spinel produced via oxide mixture method was investigated. For this reason, the stoichiometric mixture of magnesite and calcined alumina as raw materials was calcined at 1100°C. The calcined mixture was milled, pressed and then, fired at 1300 and 1500°C after addition of various amounts of MgCl2. Besides, the physical properties, phase composition and microstructure of fired samples were investigated. The results showed that MgCl2 addition has great effect on the densification and particle size of spinel. Besides, MgCl2 addition increases the amount of spinel phase at all firing temperatures. Due to the decomposition of MgCl2 and then formation of ultra-fine MgO particles, the nano-sized spinel is formed on the surface of the larger spinel particles.

Nano-structure formation of Fe-Pt perpendicular magnetic recording media co-deposited with MgO, Al2O3 and SiO2 additives

International Nuclear Information System (INIS)

Safran, G.; Suzuki, T.; Ouchi, K.; Barna, P.B.; Radnoczi, G.

2006-01-01

Perpendicular magnetic recording media samples were prepared by sputter deposition on sapphire with a layer sequence of MgO seed-layer/Cr under-layer/FeSi soft magnetic under-layer/MgO intermediate layer/FePt-oxide recording layer. The effects of MgO, Al 2 O 3 and SiO 2 additives on the morphology and orientation of the FePt layer were investigated by transmission electron microscopy. The samples exhibited (001) orientation of the L1 FePt phase with the mutual orientations of sapphire substrate//MgO(100)[001]//Cr(100)[11-bar0]//FeSi(100)[11-bar0]//MgO(100) [001]//FePt(001)[100]. The morphology of the FePt films varied due to the co-deposited oxides: The FePt layers were continuous and segmented by stacking faults aligned at 54 o to the surface. Films with SiO 2 addition, beside the oriented columnar FePt grains, exhibited a fraction of misoriented crystallites due to random repeated nucleation. Al 2 O 3 addition resulted in a layered structure, i.e. an initial continuous epitaxial FePt layer covered by a secondary layer of FePt-Al 2 O 3 composite. Both components (FePt and MgO) of the MgO-added samples were grown epitaxially on the MgO intermediate layer, so that a nano-composite of intercalated (001) FePt and (001) MgO was formed. The revealed microstructures and formation mechanisms may facilitate the improvement of the structural and magnetic properties of the FePt-oxide composite perpendicular magnetic recording media

Lubrication performance and mechanisms of Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxide nanoparticles as lubricant additives

International Nuclear Information System (INIS)

Li, Shuo; Bhushan, Bharat

2016-01-01

Highlights: • Mg/Al-, Zn/Al- and Zn/Mg/Al-layered double hydroxide were synthesized. • Mg/Al-LDH had superior tribological performance compared to other LDHs. • The best thermal stability of Mg/Al-LDH was responsible for its friction property. - Abstract: Solid lubricant particles are commonly used as oil additives for low friction and wear. Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxides (LDH) were synthesized by coprecipitation method. The benefits of LDH nanoparticles are that they can be synthesized using chemical methods where size and shape can be controlled, and can be modified organically to allow dispersal in fluids. The LDH nanoparticles were characterized by X-ray diffraction, scanning electron microscope, thermogravimetry, and differential scanning calorimetry. A pin-on-disk friction and wear tester was used for evaluating the friction and wear properties of LDH nanoparticles as lubricant additives. LDH nanoparticles have friction-reducing and anti-wear properties compared to oil without LDHs. Mg/Al-LDH has the best lubrication, possibly due to better thermal stability in severe conditions.

Lubrication performance and mechanisms of Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxide nanoparticles as lubricant additives

Energy Technology Data Exchange (ETDEWEB)

Li, Shuo [School of Materials Science and Technology, China University of Geosciences (Beijing), 29 Xueyuan Road, Haidian Distract, Beijing 100083 (China); Nanoprobe Laboratory for Bio- & Nanotechnology and Biomimetics (NLBB), The Ohio State University, 201 W. 19th Avenue Columbus, OH 43210-1142 (United States); Bhushan, Bharat, E-mail: bhushan.2@osu.edu [Nanoprobe Laboratory for Bio- & Nanotechnology and Biomimetics (NLBB), The Ohio State University, 201 W. 19th Avenue Columbus, OH 43210-1142 (United States)

2016-08-15

Highlights: • Mg/Al-, Zn/Al- and Zn/Mg/Al-layered double hydroxide were synthesized. • Mg/Al-LDH had superior tribological performance compared to other LDHs. • The best thermal stability of Mg/Al-LDH was responsible for its friction property. - Abstract: Solid lubricant particles are commonly used as oil additives for low friction and wear. Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxides (LDH) were synthesized by coprecipitation method. The benefits of LDH nanoparticles are that they can be synthesized using chemical methods where size and shape can be controlled, and can be modified organically to allow dispersal in fluids. The LDH nanoparticles were characterized by X-ray diffraction, scanning electron microscope, thermogravimetry, and differential scanning calorimetry. A pin-on-disk friction and wear tester was used for evaluating the friction and wear properties of LDH nanoparticles as lubricant additives. LDH nanoparticles have friction-reducing and anti-wear properties compared to oil without LDHs. Mg/Al-LDH has the best lubrication, possibly due to better thermal stability in severe conditions.

Effect of the addition of Al-Ti-C master alloy on the microstructure and microhardness of a cast Al-10Mg alloy

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

The microstructure and microhardness of a cast Al-10wt%Mg (henceforth Al-l0Mg) alloy with 0.2wt% addition of Al-5Ti-0.25C master alloy were compared with those of a refiner-free alloy of similar chemical composition.It was found that this level of the master alloy addition not only caused an effective grain refinement, but also caused a significant increase in the microhardness of the Al-10Mg alloy.Microchemical analysis revealed that TiC particles existed in the grain center.The relationship between the holding time and grain size was also studied.It shows that the grain refining efficiency is faded observably with the holding time.This is explained in terms of the instability of TiC particles.

Strengthening and toughening of poly(L-lactide) composites by surface modified MgO whiskers

Energy Technology Data Exchange (ETDEWEB)

Wen, Wei [Biomaterial Research Laboratory, Department of Material Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Luo, Binghong, E-mail: tluobh@jnu.edu.cn [Biomaterial Research Laboratory, Department of Material Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Engineering Research Center of Artificial Organs and Materials, Ministry of Education, Guangzhou 510632 (China); Qin, Xiaopeng; Li, Cairong [Biomaterial Research Laboratory, Department of Material Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Liu, Mingxian; Ding, Shan [Biomaterial Research Laboratory, Department of Material Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Engineering Research Center of Artificial Organs and Materials, Ministry of Education, Guangzhou 510632 (China); Zhou, Changren, E-mail: tcrz9@jnu.edu.cn [Biomaterial Research Laboratory, Department of Material Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Engineering Research Center of Artificial Organs and Materials, Ministry of Education, Guangzhou 510632 (China)

2015-03-30

Highlights: • The grafted PLLA chain on the surface of g-MgO whisker was ruled out by FTIR spectroscopy and TG/DTG analyses. • The excellent dispersion of g-MgO whiskers and the strong interfacial adhesion of g-MgO whiskers/PLLA composite were proved by FSEM. • Comparing to MgO particles and MgO whiskers, fibrous-like g-MgO whiskers are the most effective reinforcing and toughening fillers for PLLA. - Abstract: To improve both the strength and toughness of poly(L-lactide) (PLLA), fibrous-like MgO whiskers with diameters of 0.15–1 μm and lengths of 15–110 μm were prepared, and subsequently surface modified with L-lactide to obtain grafted MgO whiskers (g-MgO whiskers). The structures and properties of MgO whiskers and g-MgO whiskers were studied. Then, a series of MgO whiskers/PLLA and g-MgO whiskers/PLLA composites were prepared by solution casting method, for comparison, MgO particles/PLLA composite was prepared too. The resulting composites were evaluated in terms of hydrophilicity, crystallinity, dispersion of whiskers, interfacial adhesion and mechanical performance by means of polarized optical microscopy (POM), contact angle measurement, field emission scanning electron microscope (FSEM), transmission electron microscopy (TEM) and tensile testing. The results revealed that the crystallization rate and hydrophilicity of PLLA were improved by the introduction of MgO whiskers and g-MgO whiskers. The g-MgO whiskers can disperse more uniformly in and show stronger interfacial adhesion with the matrix than MgO whiskers as a result of the surface modification. Due to the bridge effect of the whiskers and the excellent interfacial adhesion between g-MgO whiskers and PLLA, g-MgO whiskers/PLLA composites exhibited remarkably higher strength, modulus and toughness compared to the pristine PLLA, MgO particles/PLLA and MgO whiskers/PLLA composites.

Structural characteristics and corrosion behavior of biodegradable Mg-Zn, Mg-Zn-Gd alloys.

Science.gov (United States)

Kubásek, J; Vojtěch, D

2013-07-01

In this research, binary Mg-Zn (up to 3 wt% Zn) and ternary Mg-Zn-Gd (up to 3 wt% Gd, 3 wt% Zn) alloys were prepared by induction melting in an argon atmosphere. The structures of these alloys were characterized using light and scanning electron microscopy, energy dispersive spectrometry, X-ray diffraction and X-ray fluorescence. In addition, Brinell hardness measurements were taken to supplement these studies. Corrosion behavior was evaluated by immersion tests and potentiodynamic measurements in a physiological solution (9 g/l NaCl). Depending on the composition, structures of the as-cast alloys contained α-Mg dendrites, MgZn, Mg5Gd and Mg3Gd2Zn3 phases. Compared to pure Mg, zinc improved the corrosion resistance of binary Mg-Zn. Gadolinium also improved the corrosion resistance in the case of Mg-1Zn-3Gd alloy. The highest corrosion rate was observed for Mg-3Zn-3Gd alloy. Our results improve the understanding of the relationships between the structure and corrosion behavior of our studied alloy systems.

Additions of precursors and elicitors improve geranylgeraniol production in Croton stellatopilosus callus cultures

Directory of Open Access Journals (Sweden)

Juraithip Wungsintaweekul

2015-02-01

Full Text Available Strategies for enhancing GGOH production in Croton stellatopilosus callus culture included additions of precursors (sodium acetate-NA, sodium pyruvate-NP, mevalonic acid lactone-MVA and elicitors (methyl jasmonate-MJ, acetylsalicylic acid-ASA, yeast extract-YE. Treated cells were evaluated for their GGOH contents by GC-FID and compared with the nontreated cells as controls. Additions of NA (25 mg/L, NP (50 mg/L and MVA (100 mg/L resulted in an enhancement of GGOH productivity to 0.61 mg/g DW, 0.52 mg/g DW and 0.70 mg/g DW, respectively, compared to the control culture (0.29 mg/g DW. Callus cultures elicited with MJ at 30 mg/L for 24 h stimulated GGOH production to 0.35 mg/g DW compared to the control culture (0.07 mg/g DW. Cells also responded to ASA (20 mg/L, 2 days and YE (0.25 g/L, 4 days and produced GGOH contents of 0.46 mg/g DW and 1.37 mg/g DW, respectively. This study has shown that isoprenoid precursors and conventional elicitors enhanced GGOH production in the C. stellatopilosus callus culture.

Characterization of bicrystalline epitaxial LaNiO{sub 3} films fabricated on MgO (1 0 0) substrates by pulsed laser deposition

Energy Technology Data Exchange (ETDEWEB)

Zheng Liang [School of Microelectronics and Solid-State Electronics, University of Electronics Science and Technology of China, Chengdu 610054 (China); Zhu Jun [School of Microelectronics and Solid-State Electronics, University of Electronics Science and Technology of China, Chengdu 610054 (China)]. E-mail: junzhu@uestc.edu.cn; Zhang Ying [School of Microelectronics and Solid-State Electronics, University of Electronics Science and Technology of China, Chengdu 610054 (China); Jiang Shuwen [School of Microelectronics and Solid-State Electronics, University of Electronics Science and Technology of China, Chengdu 610054 (China); Li Yanrong [School of Microelectronics and Solid-State Electronics, University of Electronics Science and Technology of China, Chengdu 610054 (China); Huawei Xian [School of Microelectronics and Solid-State Electronics, University of Electronics Science and Technology of China, Chengdu 610054 (China); Li Jinlong [School of Microelectronics and Solid-State Electronics, University of Electronics Science and Technology of China, Chengdu 610054 (China)

2006-03-15

A series of metallic LaNiO{sub 3} (LNO) thin films were deposited on MgO (1 0 0) substrates by pulsed laser deposition (PLD) under the oxygen pressure of 20 Pa at different substrate temperatures from 450 to 750 deg. C. X-ray diffraction (XRD) was used to characterize the crystal structure of LNO films. {theta}-2{theta} scans of XRD indicate that LNO film deposited at a substrate temperature of 700 deg. C has a high orientation of (l l 0). At other substrate temperatures, the LNO films have mixed phases of (l l 0) and (l 0 0). Furthermore, pole figure measurements show that LNO thin films, with the bicrystalline structure, were epitaxially deposited on MgO (1 0 0) substrates in the mode of LNO (1 1 0)//MgO (1 0 0) at 700 deg. C. Reflection high-energy electric diffraction (RHEED) and atomic force microscopy (AFM) were also performed to investigate the microstructure of LNO films with the high (l l 0) orientation. RHEED patterns clearly confirm this epitaxial relationship. An atomically smooth surface of LNO films at 700 deg. C was obtained. In addition, bicrystalline epitaxial LNO films, fabricated at 700 deg. C, present a excellent conductivity with a lower electrical resistivity of 300 {mu} {omega} cm. Thus, the obtained results indicate that bicystalline epitaxial LNO films could serve as a promising candidate of electrode materials for the fabrication of ferroelectric or dielectric films.

Comparison of Ca2+ and Mg2+ enhancing aerobic granulation in SBR

International Nuclear Information System (INIS)

Liu Lin; Gao Dawen; Zhang Min; Fu Yuan

2010-01-01

Two sequencing batch reactors (SBRs) were operated to investigate the effect of Ca 2+ and Mg 2+ augmentation on aerobic granulation. Reactor R1 was augmented with Ca 2+ at 40 mg/L, while Mg 2+ was added to the reactor R2 with 40 mg/L. Results showed that the reactor R1 had a faster granulation process compared with R2, and the mature granules in R1 showed better physical characteristics. However, the mature granules in R2 had the higher production yield of polysaccharides and proteins, and aerobic granules in R2 experienced a faster substrate biodegradation. Microbial and genetic characteristics in mature granules were analyzed using polymerase chain reaction (PCR) and denaturing gradient gel electrophoresis (DGGE) techniques. The results revealed that Mg 2+ addition led to higher microbial diversity in mature granules. In addition, an uncultured bacterium (AB447697) was major specie in R1, and β-proteobacterium was dominant in R2. It can be concluded that Ca 2+ had an important effect on physical properties of aerobic granules, while Mg 2+ played a key role on biological properties during the sludge granulation.

Influence of additive L-phenylalanine on stabilization of metastable α-form of L-glutamic acid in cooling crystallization

Science.gov (United States)

Quang, Khuu Chau; Nhan, Le Thi Hong; Huyen, Trinh Thi Thanh; Tuan, Nguyen Anh

2017-09-01

The influence of additive amino acid L-phenylalanine on stabilization of metastable α-form of L-glutamic acid was investigated in cooling crystallization. The present study found that the additive L-phenylalanine could be used to stabilize the pure metastable α-form in L-glutamic acid crystallization, where the additive concentration of 0.05-0.1 (g/L) was sufficient to stabilize the 100% wt metastable α-form in solid product at L-glutamic acid concentration of 30-45 (g/L). Additionally, the present results indicated that the adsorption of additive L-phenylalanine on the (001) surface of α-form was more favorable than that of the β-form molecular, so the nucleation sites of stable β-form was occupied by additive molecular, which resulted in inhibition of nucleation and growth of β-form, allowing stabilization of metastable α-form.

Direct observation of the crystal structure changes in the Mg{sub x}Zn{sub 1−x}O alloy system

Energy Technology Data Exchange (ETDEWEB)

Yoo, Seung Jo; Lee, Ji-Hyun; Kim, Chang-Yeon [Nano-Bio Electron Microscopy Research Group, Korea Basic Science Institute (KBSI), 169-148 Gwahak-ro, Yuseong-gu, Daejeon 305-806 (Korea, Republic of); Kim, Chang Hoi [Department of Nano Semiconductor Engineering, Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-Gu, Busan 606-791 (Korea, Republic of); Shin, Jae Won [Nano-Bio Electron Microscopy Research Group, Korea Basic Science Institute (KBSI), 169-148 Gwahak-ro, Yuseong-gu, Daejeon 305-806 (Korea, Republic of); Center for Nanomaterials and Chemical Reactions, Institute for Basic Science (IBS), Daejeon 305-701 (Korea, Republic of); Kim, Hong Seung, E-mail: hongseung@hhu.ac.kr [Department of Nano Semiconductor Engineering, Korea Maritime and Ocean University, 727 Taejong-ro, Yeongdo-Gu, Busan 606-791 (Korea, Republic of); Kim, Jin-Gyu, E-mail: jjintta@kbsi.re.kr [Nano-Bio Electron Microscopy Research Group, Korea Basic Science Institute (KBSI), 169-148 Gwahak-ro, Yuseong-gu, Daejeon 305-806 (Korea, Republic of)

2015-08-03

We directly observed the crystal structure changes of the Mg{sub x}Zn{sub 1−x}O alloy thin film deposited on Si (111) substrates. Through the in situ heating transmission electron microscopy study, it was determined that the crystal structure changes did not occur up to at 400 °C, whereas the disappearance of the hexagonal structure was observed at 500 °C in the layer of nanosized grains. Additionally, the decreased intensity of the Zn L-edge was analyzed in the comparison of the core loss electron energy loss spectroscopy spectra of the Zn L-edge and the Mg K-edge obtained at room temperature and 500 °C. Based on these experimental results, the process of crystal structure changes could be explained by the evaporation of Zn atoms in the Mg{sub x}Zn{sub 1−x}O alloy system. This phenomenon is prominent in the improvement of the microstructure of the Mg{sub x}Zn{sub 1−x}O alloy thin film by controlling the thermal annealing temperature. - Highlights: • Mg{sub x}Zn{sub 1−x}O thin films coexisting with cubic and hexagonal structures were deposited. • Crystal structure changes of the thin films were directly observed at 500 °C. • The process of microstructure changes could be caused by the evaporation of Zn atoms.

[Sewage sludge conditioning by bioleaching-dual PAC and PAM addition].

Science.gov (United States)

Liu, Chang-Geng; Zhang, Pan-Yue; Zeng, Guang-Ming; Liu, Yong-Gang

2010-09-01

Bioleaching-dual polyaluminum chloride (PAC) and polyacrylamide (PAM) addition was used to condition sewage sludge. The results showed that FeSO4 x 7H2O addition improved the bioleaching rate obviously with a fixed sulfur power dosage of 3 g x L(-1); when the FeSO4 x 7H2O dosage was 8 g x L(-1), the bioleaching lasted 1.5 d to decrease the sludge pH below 2. Bioleaching improved the sludge dewaterability significantly with a specific resistance to filtration (SRF) reduction of 77.52% from 6.45 x 10(10)s2 x g(-10 to 1.45 x 10(10)s2 x g(-1), but the bioleached sludge was still difficult to be dewatered. After adjusting the bioleached sludge pH to 6, PAC and PAM were used to enhance conditioning of the bioleached sludge. The results indicated that the optimal dosage was 200 mg x L(-1) for PAC or 50 mg x L(-1) for PAM when single chemical was used. When PAC and PAM were dually used, the optimal dosages of PAC and PAM were 100 mg x L(-1) and 25 mg x L(-1), respectively; SRF and moisture of sludge cake reduced to 2.02 x 10(8) s2 x g(-1) and 74.81%, respectively, showing good dewaterability of the treated sludge. Compared with the single use of PAC and PAM, the dual use of PAC and PAM showed the advantages of lower cost and better conditioning effect.

Influence of different extracts addition on total phenols, anthocyanin content and antioxidant activity of blackberry juice during storage

Directory of Open Access Journals (Sweden)

Blanka Bilić

2011-01-01

Full Text Available The aim of this study was investigation of influence of different extracts addition on total phenols, anthocyanin content, antioxidant activity and percent of polymeric colour of blackberry juice during storage of 52 days at 4 °C. Anthocyanin content of control sample (blackberry juice without extracts addition was 149.91 mg/L. Samples with addition of extracts (olive leaf, pine bark PE 5:1, pine bark PE 95 %, green tea, red wine PE 30 %, red wine PE 4:1 and bioflavonoids had higher anthocyanin content (from 152.42 to 161.19 mg/L in comparison to control sample. Sample with addition of bioflavonoids had the highest anthocyanin content. Samples with addition of extracts had much higher total phenol content and antioxidant activity than control sample, what was expected since extracts are rich in phenols. During storage decrease of phenols, anthocyanins and antioxidant activity occurred in higher or lesser extent, depending on extract type addition. Anthocyanin content in control sample was 119.85 mg/L. Samples with addition of bioflavonoids, olive leaf, pine bark PE 5:1 and red wine PE 4:1 had lower (from 103.44 to 118.84 mg/L, while other samples had higher (from 131.99 to 135.57 mg/L anthocyanin content than control sample. After storage, decrease of anthocyanins was followed with increase of percent of polymeric colour, with exception of samples with addition of green tea.

Influence of Mg O and B2O3 addition on reaction sintering, properties and microstructure of Aluminum titanate

International Nuclear Information System (INIS)

Ajami, R.; Sarpoolaki, H.; Akbari, G. H.

2007-01-01

The effect of Mg O and B 2 O 3 on the formation, physical properties, phase analysis and microstructure of aluminum titanate was investigated. Density results showed the sample containing of 1 wt percent B 2 O 3 and 2 wt percent Mg O leads to the highest density while the lowest density was seen in samples containing 1 wt percent B 2 O 3 compared to pure aluminum titanate. Regarding the phase analysis of samples, Mg O was found most effective additive on reaction sintering of aluminum titanate through the intermediate phases. Furthermore at the temperatures above 1350 d eg C , B 2 O 3 promote the formation reaction of aluminum titanate. Microstructural analysis showed the samples containing Mg O are fine grain and homogeneous. Thermal expansion coefficient of samples with additives is greater than pure aluminum titanate. Pure aluminum titanate samples and one containing B 2 O 3 additive decompose to Al 2 O 3 and TiO 2 after 5 hours heat treatment at 1150 d eg C while the samples containing 2 wt percent Mg O was stable even after 25 hours

Variation du coefficient de collage de l'argent et de l'or durant leur condensation sur film de MgO

Science.gov (United States)

Desrousseaux, G.; Carlan, A.; Jiang, Z.

1993-10-01

The incidence rate dependence of the sticking coefficient during the growth of gold (or silver) condensate on MgO film is experimentally investigated for a substrate kept at room temperature. This MgO substrate is deposited on quartz monitor by evaporation under UHV from a Knudsen cell. Then, from another cell, the flux of metal atoms impinges on the MgO film which covers the quartz. Under this flux of incident metal atoms, the changes (respectively θ and f) of the temperature and of the frequency of the quartz oscillator are then simultaneously recorded. Both continuous measurements enable us to calculate, at different times t, the sticking coefficient η (t) defined as the ration between the condensed metal rate q and the incident rate R. We use the results to plot η versus t and examine the slope of η-rise until the time t at which η (t) reaches unity. The progression of η (t) reaches unity. The progression of η (t) from zero to unity during the metal deposition is explained by assuming that the nucleation on preferred sites with capture of adatoms at the edge of stable germs is the prevailing condensation mechanism at the initial stage of the condensation. Our experimental results could be fitted better by assuming an exponential growth of the site occupation than an increase of the number density n_s(t) with (Rt)^{1/3}. On étudie expérimentalement la dépendance que peut présenter, par rapport au flux métallique incident, la progression vers l'unité du coefficient de collage. Pour cela, on suit cette progression pour l'or et l'argent condensés sur film de MgO à température proche de l'ambiante. Le substrat de MgO est déposé sur un quartz de pesée par évaporation sous ultra-vide à partir d'une cellule de Knudsen. Une autre cellule est utilsée pour déposer l'un de ces métaux sur le film de MgO couvrant le quartz. Les variations θ et f de la température et de la fréquence d'oscillations du quartz de pesée sous le flux d'atomes incidents

XRD investigation of the Effect of MgO Additives on ZTA-TiO2 Ceramic Composites

Science.gov (United States)

Azhar, Ahmad Zahirani Ahmad; Manshor, Hanisah; Ali, Afifah Mohd

2018-01-01

Alumina (Al2O3) based ceramics possess good mechanical properties and suitable for the application of cutting inserts. However, this monolithic ceramics suffer from lack of toughness. Hence, there are some modification were made such as the addition of yttria stabilized zirconia (YSZ) to the Al2O3 helps in increasing the toughness of the Al2O3 ceramics. Some additives such as MgO and TiO2 were used to further improve the mechanical properties of ZTA. In this study, high purity raw materials which consist of ZTA-TiO2 were mixed with different amount of MgO (0.0 - 1.0 wt %). The mixture of materials was going through wet mixing, compaction and pressureless sintering at 1600°C for one hour. The samples were characterized for phase analysis, microstructure, shrinkage rate, bulk density, Vickers hardness and fracture toughness. Based on the XRD analysis results, the secondary phase (MgAl2O4) was detected in the sample with 0.5 wt% of MgO onwards which leads to grains refinement, thus improve the density and hardness of ZTA-TiO2-MgO ceramics composites.

Effect of iron and magnesium addition for ethanol production from the conversion of palm oil mill effluent by anaerobic processes

Science.gov (United States)

Handajani, M.; Gumilar, A.; Syafila, M.

2018-01-01

Nowadays, crisis of the energy is the main problem in the world. Currently, most the energy resource derived from the fossil material that cannot be refurbished. Ethanol is an alternative fuel that content as a fossil fuels. Wastewater with the high concentration of the organic can be used for the ethanol production to replace foodstuff as a raw material. In this study, palm oil mill effluent (POME) with the concentration of COD is 24,500 mg/L has been used as a substrate. The purpose of this study was to determine the effect of the metal addition in the substrate metabolic pathways. Circulating batch reactor (CBR) is used with the flushing N2 1L/min for 24 hours and continued operates for 72 hours by internal biogas. The additional variation concentration of Fe(II) ion are 0.5; 1.0 and 2.5 mg/L, and Mg(II) are 0.5 and 1.5 mg/L were added by combination. The results showed that the combination of Fe (II) 2.5 mg/L and Mg(II) 1.5 mg/L produced the highest ethanol concentration is 715.8 mg/L and degree of acidification (DA) 0.284-0.357. Another combination of Fe(II) and Mg(II) provide results for the ethanol production 463.7-689.7 mg/L with the rate of ethanol production is 1.09-26.5 mg/L/hour.

The influence of Ni addition and hot-extrusion on the microstructure and tensile properties of Al–15%Mg2Si composite

International Nuclear Information System (INIS)

Emamy, M.; Khodadadi, M.; Honarbakhsh Raouf, A.; Nasiri, N.

2013-01-01

Highlights: ► Ni content on the microstructure and tensile properties of Al–Mg 2 Si composite. ► Ni changed the size of primary Mg 2 Si from 42 μm to 17 μm. ► Higher UTS and elongation values obtained by addition of 5 wt% Ni. ► Fracture behavior changed from brittle to ductile by Ni addition and extrusion. - Abstract: The effects of nickel addition and hot-extrusion on the microstructure and tensile properties of in situ Al–15%Mg 2 Si composite specimens have been investigated. Al–15%Mg 2 Si composite ingots were prepared by an in situ process and different amounts of nickel (0.1, 0.3, 0.5, 1.0, 3.0 and 5.0 wt% Ni) were added to the remelted composite. Optical microscopy (OM) and scanning electron microscopy (SEM) indicated that Ni addition changes the morphology of both primary and eutectic Mg 2 Si phases and decreases the size of primary Mg 2 Si particles from 42 μm to 17 μm. Hot-extrusion was found to be powerful in breaking the eutectic network and changing the size and morphology of pseudo-eutectic Mg 2 Si phase. The results obtained from tensile testing revealed that both Ni addition and hot-extrusion process improve ultimate tensile strength (UTS) and elongation values. Fracture surface examinations revealed a transition from brittle fracture mode in as-cast composite to ductile fracture in hot-extruded composite after Ni addition. This can be attributed to the changes in size and morphology of primary and eutectic Mg 2 Si phases and also the formation of more and finer α-Al phase

L1 and L2 Distance Effects in Learning L3 Dutch

Science.gov (United States)

Schepens, Job J.; der Slik, Frans; Hout, Roeland

2016-01-01

Many people speak more than two languages. How do languages acquired earlier affect the learnability of additional languages? We show that linguistic distances between speakers' first (L1) and second (L2) languages and their third (L3) language play a role. Larger distances from the L1 to the L3 and from the L2 to the L3 correlate with lower…

Relative bioavailability of a newly developed 5-mg levomethadone hydrochloride IR tablet (L-Polamidon® 5 mg tablets) in comparison with the 5-mg levomethadone hydrochloride oral solution (L-Polamidon® solution for substitution) as reference product.

Science.gov (United States)

Blume, Henning H; Wedemeyer, Ralf-Steven; Donath, Frank; Roscher, Katrin; Elvert, Gerd; Wagner, Daniel; Bley, Oliver; Vuia, Alexander; Todorova-Sanjari, Marina; Villalobos, Ramon; Schug, Barbara

2015-04-01

To establish the relative bioavailability (rBA) between two p.o. 5-mg levomethadone hydrochloride formulations, i.e., L-Polamidon® 5 mg tablets (test) vs. L-Polamidon® solution for substitution (reference). To assess the safety and tolerability of both formulations. A total of 33 healthy male subjects, aged 29 ± 6 years (BMI: 23.9 ± 2.5 kg/m2) completed this single center, open-label, randomized, 2-period cross-over study with single dose administrations under fasting conditions and coadministration with naltrexone for safety reasons. Administrations of both investigational products were separated by a washout period of at least 2 weeks, i.e., 13 treatmentfree days. The total dose for each subject was 2 x 5 mg resulting in 10 mg levomethadone hydrochloride. For pharmacokinetic evaluation, blood samples were withdrawn until 72 hours postdose. A validated non-stereoselective liquid chromatography-tandem mass spectroscopy method (LC-MS/MS) was applied for the determination of levomethadone in plasma. The lower limit of quantitation was 0.100 ng/mL. Adverse events were descriptively analyzed in the study population. The geometric means of the parameters related with the extent of total exposure of levomethadone, i.e., AUC(0-tlast) and AUC(0-∞), were 244.422 ng x h/mL and 332.999 ng x h/mL for test and 246.837 ng x h/mL and 329.467 ng×h/mL for reference, respectively. The geometric means of the peak exposure for levomethadone, i.e., Cmax, were 8.923 ng/mL for test and 8.635 ng/mL for reference. The point estimates (PEs) of the Test/Reference (T/R) adjusted geometric mean ratios of AUC(0-last), AUC(0-∞), and C(max) were 99.20%, 101.42%, and 104.11%, respectively, and all of them showed 90%-confidence intervals (CIs) within the range of 80.00 - 125.00% as suggested by regulatory requirements for bioequivalence assessment In total, 21 subjects experienced 55 AEs during the study, the most frequently reported AE, i.e., headache, accounted for 13 out of the total

Performance of Mg-14Li-1Al-0.1Ce as anode for Mg-air battery

Energy Technology Data Exchange (ETDEWEB)

Ma, Yibin; Li, Deyu [School of Chemical Engineering and Technology, Harbin Institute of Technology, West Street No. 92, Harbin 150001 (China); Li, Ning [School of Chemical Engineering and Technology, Harbin Institute of Technology, West Street No. 92, Harbin 150001 (China); Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin Engineering University, Harbin 150001 (China); Zhang, Milin; Huang, Xiaomei [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin Engineering University, Harbin 150001 (China)

2011-02-15

In this research, a new Mg-air battery based on Mg-14Li-1Al-0.1Ce was prepared and the battery performance was investigated by constant current discharge test. The corrosion behavior of Mg, AZ31 and Mg-Li-Al-Ce were studied by self-corrosion rate measurement and potentiodynamic polarization measurement. The characteristics of Mg-Li-Al-Ce after discharge were investigated by electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results show that Mg-Li-Al-Ce is more active than Mg and AZ31. The self-corrosion rate is found to be in the order: Mg-Li-Al-Ce < Mg < AZ31. It has been observed that the Mg-air battery based on Mg-Li-Al-Ce offers higher operating voltage, anodic efficiency and capacity than those with Mg and AZ31. SEM and EIS results show that the discharge product of Mg-Li-Al-Ce is loosely adhered to the alloy surface, and thus Mg-Li-Al-Ce could keep high discharge activity during discharge. (author)

House dust mite induces expression of intercellular adhesion molecule-1 in EoL-1 human eosinophilic leukemic cells.

Science.gov (United States)

Kwon, Byoung Chul; Sohn, Myung Hyun; Kim, Kyung Won; Kim, Eun Soo; Kim, Kyu-Earn; Shin, Myeong Heon

2007-10-01

The house dust mite (HDM) is considered to be the most common indoor allergen associated with bronchial asthma. In this study, we investigated whether crude extract of the HDM Dermatophagoides farinae could activate human eosinophilic leukemic cells (EoL-1) to induce upregulation of cell-surface adhesion molecules. When EoL-1 cells were incubated with D. farinae extract, expression of intercellular adhesion molecule-1 (ICAM-1) significantly increased on the cell surfaces compared to cells incubated with medium alone. In contrast, surface expression of CD11b and CD49d in EoL-1 cells was not affected by D. farinae extract. In addition, pretreatment of cells with NF-kappaB inhibitor (MG-132) or JNK inhibitor (SP600125) significantly inhibited ICAM-1 expression promoted by HDM extract. However, neither p38 MAP kinase inhibitor nor MEK inhibitor prevented HDM-induced ICAM-1 expression in EoL-1 cells. These results suggest that crude extract of D. farinae induces ICAM-1 expression in EoL-1 cells through signaling pathways involving both NF-kappaB and JNK.

Comparative Effectiveness of Vancomycin Versus Daptomycin for MRSA Bacteremia With Vancomycin MIC >1 mg/L: A Multicenter Evaluation.

Science.gov (United States)

Moise, Pamela A; Culshaw, Darren L; Wong-Beringer, Annie; Bensman, Joyce; Lamp, Kenneth C; Smith, Winter J; Bauer, Karri; Goff, Debra A; Adamson, Robert; Leuthner, Kimberly; Virata, Michael D; McKinnell, James A; Chaudhry, Saira B; Eskandarian, Romic; Lodise, Thomas; Reyes, Katherine; Zervos, Marcus J

2016-01-01

Clinical studies comparing vancomycin with alternative therapy for methicillin-resistant Staphylococcus aureus (MRSA) bacteremia are limited. The objective of this study was to compare outcomes of early daptomycin versus vancomycin treatment for MRSA bacteremia with high vancomycin MICs in a geographically diverse multicenter evaluation. This nationwide, retrospective, multicenter (N = 11), matched, cohort study compared outcomes of early daptomycin with vancomycin for MRSA bloodstream infection (BSI) with vancomycin MICs 1.5 to 2 µg/mL. Matching variables, based on propensity regression analysis, included age, intensive care unit (ICU), and type of BSI. Outcomes were as follows: (1) composite failure (60-day all-cause mortality, 7-day clinical or microbiologic failure, 30-day BSI relapse, or end-of-treatment failure (EOT; discontinue/change daptomycin or vancomycin because of treatment failure or adverse event]); (2) nephrotoxicity; and (2) day 4 BSI clearance. A total of 170 patients were included. The median (interquartile range) age was 60 years (50-74); the median (range) Acute Physiology and Chronic Health Evaluation II score was 15 (10-18); 31% were in an ICU; and 92% had an infectious disease consultation. BSI types included endocarditis/endovascular (39%), extravascular (55%), and central catheter (6%). The median daptomycin dose was 6 mg/kg, and the vancomycin trough level was 17 mg/L. Overall composite failure was 35% (59 of 170): 15% due to 60-day all-cause mortality, 14% for lack of clinical or microbiologic response by 7 days, and 17% due to failure at end of therapy (discontinue/change because of treatment failure or adverse event). Predictors of composite failure according to multivariate analysis were age >60 years (odds ratio, 3.7; P day 4 bacteremia clearance rates for immunocompromised patients (n = 26) (94% vs 56% for daptomycin vs vancomycin; P = 0.035). Results from this multicenter study provide, for the first time, a geographically diverse

Addition of MgO nanoparticles and plasma surface treatment of three-dimensional printed polycaprolactone/hydroxyapatite scaffolds for improving bone regeneration

Energy Technology Data Exchange (ETDEWEB)

Roh, Hee-Sang; Lee, Chang-Min; Hwang, Young-Hyoun [Department of Dental Materials, School of Dentistry, Chosun University, Gwangju 61452 (Korea, Republic of); Kook, Min-Suk [Department of Oral & Maxillofacial Surgery, School of Dentistry, Chonnam National University, Gwangju 61186 (Korea, Republic of); Yang, Seong-Won [Department of Ophthalmology, College of Medicine, Chosun University, Gwangju 61452 (Korea, Republic of); Lee, Donghun [Department of Herbal Pharmacology, Kyung Hee University College of Korean Medicine, Seoul 130-701 (Korea, Republic of); Kim, Byung-Hoon, E-mail: kim5055@chosun.ac.kr [Department of Dental Materials, School of Dentistry, Chosun University, Gwangju 61452 (Korea, Republic of)

2017-05-01

Magnesium (Mg) plays an important role in the body in mediating cell-extracellular matrix interactions and controlling bone apatite structure and density. Hydroxyapatite (HAp) has been used for osteoconductive bone replacement because of its good compressive strength and biocompatibility. The object of this study is to investigate the effects of adding Magnesium oxide (MgO) nanoparticles to polycaprolactone (PCL)/HAp composites and treating PCL/HAp/MgO scaffolds with oxygen and nitrogen plasma. The 3D PCL/HAp/MgO scaffolds were fabricated using a 3D bioextruder. PCL was mixed with 1–15 wt% of MgO and HAp. The scaffolds were treated with oxygen and nitrogen plasma under anisotropic etching conditions to improve the bioactivity. The plasma-treated surfaces were analyzed by X-ray photoelectron spectroscopy, scanning electron microscopy, and atomic force microscopy. In addition, the proliferation and differentiation of pre-osteoblast (MC3T3-E1) cells were examined by 3-(4,5-Dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay and alkaline phosphatase activity. Cell mineralization within the produced scaffolds was analyzed by the quantification of alizarin stainings. The addition of MgO/HAp nanoparticles and plasma treatment enhanced the adhesion, proliferation, and differentiation of MC3T3-E1 cells in the PCL scaffolds. Hence, changes in physical surface morphology and surface chemical properties of the 3D scaffold by plasma treatment can affect the behavior of MC3T3-E1 cells. - Highlights: • 3D-printed PCL/HAp/MgO showed good porosity and interconnectivity. • O{sub 2} and N{sub 2} plasma improved the surface roughness and hydrophilicity on scaffolds. • Addition of HAp/MgO nanoparticles enhanced the cell behavior of preosteoblast.

Effects of ageing treatment on microstructures and properties of Mg-Gd-Y-Zr alloys with and without Zn additions

International Nuclear Information System (INIS)

Liu, X.B.; Chen, R.S.; Han, E.H.

2008-01-01

Mg-10Gd-3Y-0.5Zr alloys with and without 1% Zn additions have been investigated using optical microscopy, scanning electron microscope and X-ray diffraction. The microstructures, ageing hardening behaviors and mechanical properties of the two alloys are compared. The extruded-T5 specimens exhibit remarkable age hardening responses during ageing from 200 to 250 deg. C. The highest peak hardness and strength of the two alloys are obtained when they are aged at 200 deg. C. Addition of 1% Zn to Mg-10Gd-3Y-0.5Zr alloy results in the greater magnitude ageing effect and better mechanical properties as well as better heat resistance. Furthermore, secondary ageing is carried out at 200 deg. C following preliminary ageing at 250 deg. C for both Mg-10Gd-3Y-0.5Zr and Mg-10Gd-3Y-1Zn-0.5Zr alloys. The ultimate tensile strength values after secondary ageing are slightly lower compared with the highest strength of the two alloys, but secondary ageing offers a better combination of high strength and ductility

Precipitation kinetics of Al-1.12 Mg{sub 2}Si-0.35 Si and Al-1.07 Mg{sub 2}Si-0.33 Cu alloys

Energy Technology Data Exchange (ETDEWEB)

Gaber, A. [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt); Gaffar, M.A. [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt)]. E-mail: mgaafar@aucegypt.edu; Mostafa, M.S. [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt); Zeid, E.F. Abo [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt)

2007-02-21

The kinetics of hardening precipitates of Al-1.12 wt.% Mg{sub 2}Si-0.35 wt.% Si (excess Si) and Al-1.07 wt.% Mg{sub 2}Si-0.33 wt.% Cu (balanced + Cu) alloys have been investigated by means of differential scanning calorimetry and hardness measurements. The excess Si enhances the precipitation kinetics and improves the strength of the material. On the other hand, however addition of Cu assist formation of the Q' phase which positively changed the alloy strength. The high binding energy between vacancies and solute atoms (Si and Mg) enhances the combination of Si, Mg and vacancies to form Si-Mg-vacancy clusters. These clusters act as nucleation sites for GP-zones. The coexistence of the {beta}'- and Q'-precipitates in the balanced + Cu alloy results in a higher peak age hardening compared to the alloy with Si in excess.

Microstructure, Tensile Properties, and Corrosion Behavior of Die-Cast Mg-7Al-1Ca- xSn Alloys

Science.gov (United States)

Wang, Feng; Dong, Haikuo; Sun, Shijie; Wang, Zhi; Mao, Pingli; Liu, Zheng

2018-02-01

The microstructure, tensile properties, and corrosion behavior of die-cast Mg-7Al-1Ca- xSn ( x = 0, 0.5, 1.0, and 2.0 wt.%) alloys were studied using OM, SEM/EDS, tensile test, weight loss test, and electrochemical test. The experimental results showed that Sn addition effectively refined grains and intermetallic phases and increased the amount of intermetallic phases. Meanwhile, Sn addition to the alloys suppressed the formation of the (Mg,Al)2Ca phase and resulted in the formation of the ternary CaMgSn phase and the binary Mg2Sn phase. The Mg-7Al-1Ca-0.5Sn alloy exhibited best tensile properties at room temperature, while Mg-7Al-1Ca-1.0Sn alloy exhibited best tensile properties at elevated temperature. The corrosion resistance of studied alloys was improved by the Sn addition, and the Mg-7Al-1Ca-0.5Sn alloy presented the best corrosion resistance.

Effects of Sm addition on microstructure and mechanical properties of a Mg-10Y alloy

Directory of Open Access Journals (Sweden)

Li Quanan

2014-01-01

Full Text Available To further increase the mechanical properties, 0.5wt.% Sm was introduced to a Mg-10Y alloy in this study. The effects of Sm addition on the microstructures and mechanical properties of the Mg-10Y alloy, especially the aged Mg-10Y alloy, were investigated. The microstructure observation and tensile tests were performed by using an optical microscopy, a scanning electron microscopy and a universal material testing machine, respectively. The phase analysis was performed using X-ray diffractometer. The results show that the 0.5wt.% Sm addition can not only promote the formation of fine and dispersed Mg24Y5 phases, but also improve their morphology and distribution; it also increases the thermal stability of Mg24Y5 phases. Sm addition is seen to increase the ultimate tensile strength of Mg-10Y alloy at elevated temperatures (200, 250, 300 and 350 ℃, while decrease the elongation. But the elongation is still up to 7.5% even at 350 ℃. In the range of 250 ℃ to 300℃, the ultimate tensile strength of the alloy reaches its maximum (with a range average of 235 MPa and is not sensitive to the temperature change, which is very useful to the application of heat-resistant magnesium alloys. Even at 350 ℃, the ultimate tensile strength of Mg-10Y-0.5Sm is still up to 155 MPa. Considering both of the ultimate tensile strength and elongation, the maximum application temperature of the Mg-10Y-0.5Sm alloy can be up to 300 ℃. The strengthening mechanisms of Mg-10Y-0.5Sm alloy are mainly attributed to dispersion strengthening of Mg24Y5 phase particles with a certain solubility of Sm and grain refinement strengthening of α-Mg matrix.

Effect of TiON–MgO intermediate layer on microstructure and magnetic properties of L1{sub 0} FePt–C–SiO{sub 2} films

Energy Technology Data Exchange (ETDEWEB)

Deng, J.Y. [Department of Materials Science and Engineering, National University of Singapore, Singapore 117576 (Singapore); Dong, K.F. [School of Automation, China University of Geosciences, Wuhan 430074 (China); Peng, Y.G.; Ju, G.P. [Seagate Technology, Fremont, CA 94538 (United States); Hu, J.F. [Data Storage Institute (DSI), Singapore 117608 (Singapore); Chow, G.M.; Chen, J.S. [Department of Materials Science and Engineering, National University of Singapore, Singapore 117576 (Singapore)

2016-11-01

The microstructure and magnetic properties of L1{sub 0} FePt–C–SiO{sub 2} films grown on TiON–MgO intermediate layer were studied. TiON–MgO layer was deposited by co-sputtering TiN and MgO–TiO{sub 2} targets at 380 °C. With increasing MgO–TiO{sub 2} doping concentration, the contact angle between FePt grains with intermediate layer gradually increased, and it was close to 90° when the volume percentage of MgO–TiO{sub 2} reached 30%. At this condition, a high out-of-plane coercivity of 19.1 kOe was obtained, while the opening-up of in-plane M-H loop was very narrow. Moreover, it was found that the out-of-plane coercivity can be further improved to 21.6 kOe, by slightly increasing the percentage of MgO–TiO{sub 2} to 35 vol%. - Highlights: • The effect of TiON–MgO intermediate layer was studied. • With increasing the MgO composition, the surface energy of intermediate layer increased, and the FePt/TiON–MgO interfacial energy decreased. The contact angle of FePt grains with intermediate layer increased with the MgO composition, and 90° contact angle could be achieved by optimizing the MgO composition. • Good perpendicular magnetic anisotropy was retained with large out-of-plane coercivity and narrow in-plane opening-up.

Influence of minor alloying additions on the glass-forming ability of Mg-Ni-La bulk metallic glasses

International Nuclear Information System (INIS)

Gonzalez, S.; Figueroa, I.A.; Todd, I.

2009-01-01

Bulk metallic glasses of Mg 60 Ni 23.6 Y x La (16.4-x) and Mg 65 Ni 20 Y x LaMM (15-x) with 0 ≤ x ≤ 1 at.% have been produced by injection casting. For the La-containing alloy a maximum amorphous diameter of 4 mm for x = 0.5 and 0.75 was obtained. The LaMM-containing alloy showed a maximum amorphous diameter of 2 mm for x = 0 and 0.25 but decreased to 1 mm with further Y additions. The glass-forming ability of the Mg 60 Ni 23.6 La 16.4 alloy decreased when La is partially substituted by small amounts of small atoms (Si or B) or by large atoms (Y and Si).

Effects of Sm addition on electromagnetic interference shielding property of Mg-Zn-Zr alloys

Energy Technology Data Exchange (ETDEWEB)

Yang, Chubin [Chongqing University, College of Materials Science and Engineering, National Engineering Research Center for Magnesium Alloy, Chongqing (China); Gannan Normal University, Jiangxi Provincial Engineering Research Center for Magnesium Alloy, Ganzhou (China); Pan, Fusheng; Chen, Xianhua [Chongqing University, College of Materials Science and Engineering, National Engineering Research Center for Magnesium Alloy, Chongqing (China); Luo, Ning [Gannan Normal University, Jiangxi Provincial Engineering Research Center for Magnesium Alloy, Ganzhou (China)

2017-06-15

The electromagnetic interference (EMI) shielding of Sm-containing magnesium alloys in the 30-1500 MHz testing frequency range was investigated by coaxial cable method. The results demonstrated that Mg-3Zn alloys displayed the best electromagnetic shielding property. When 0.5 wt% of Zr was added for crystal grain refinement, the shielding effectiveness (SE) was apparently reduced. The addition of the rare earth element Sm in ZK magnesium alloys can improve the electromagnetic interference shielding of magnesium alloys. The main reason for the differences in electromagnetic interference shielding of magnesium alloys was the change in conductivity. The addition of Zr in Mg-Zn alloys can refine the grains and consequently improve the grain boundary area significantly. Therefore, the number of irregularly arranged atoms at the grain boundaries increased, decreasing the conductivity of magnesium alloys and leading to a decrease in the electromagnetic interference shielding. Following the Sm addition, the Mg-Zn-Sm phase was precipitated at the grain boundaries and in cores. The precipitation of Sm-containing rare earth phases could consume the solid-soluted Zn atoms within the Mg, resulting in an increase in electrical conductivity and electromagnetic interference shielding improvement. (orig.)

AFFECTS OF MECHANICAL MILLING AND METAL OXIDE ADDITIVES ON SORPTION KINETICS OF 1:1 LiNH2/MgH2 MIXTURE

Energy Technology Data Exchange (ETDEWEB)

Erdy, C.; Anton, D.; Gray, J.

2010-12-08

The destabilized complex hydride system composed of LiNH{sub 2}:MgH{sub 2} (1:1 molar ratio) is one of the leading candidates of hydrogen storage with a reversible hydrogen storage capacity of 8.1 wt%. A low sorption enthalpy of {approx}32 kJ/mole H{sub 2} was first predicted by Alapati et al. utilizing first principle density function theory (DFT) calculations and has been subsequently confirmed empirically by Lu et al. through differential thermal analysis (DTA). This enthalpy suggests that favorable sorption kinetics should be obtainable at temperatures in the range of 160 C to 200 C. Preliminary experiments reported in the literature indicate that sorption kinetics are substantially lower than expected in this temperature range despite favorable thermodynamics. Systematic isothermal and isobaric sorption experiments were performed using a Sievert's apparatus to form a baseline data set by which to compare kinetic results over the pressure and temperature range anticipated for use of this material as a hydrogen storage media. Various material preparation methods and compositional modifications were performed in attempts to increase the kinetics while lowering the sorption temperatures. This paper outlines the results of these systematic tests and describes a number of beneficial additions which influence kinetics as well as NH{sub 3} formation.

Affects of Mechanical Milling and Metal Oxide Additives on Sorption Kinetics of 1:1 LiNH2/MgH2 Mixture

Directory of Open Access Journals (Sweden)

Donald L. Anton

2011-05-01

Full Text Available The destabilized complex hydride system composed of LiNH2:MgH2 (1:1 molar ratio is one of the leading candidates of hydrogen storage with a reversible hydrogen storage capacity of 8.1 wt%. A low sorption enthalpy of ~32 kJ/mole H2 was first predicted by Alapati et al. utilizing first principle density function theory (DFT calculations and has been subsequently confirmed empirically by Lu et al. through differential thermal analysis (DTA. This enthalpy suggests that favorable sorption kinetics should be obtainable at temperatures in the range of 160 °C to 200 °C. Preliminary experiments reported in the literature indicate that sorption kinetics are substantially lower than expected in this temperature range despite favorable thermodynamics. Systematic isothermal and isobaric sorption experiments were performed using a Sievert’s apparatus to form a baseline data set by which to compare kinetic results over the pressure and temperature range anticipated for use of this material as a hydrogen storage media. Various material preparation methods and compositional modifications were performed in attempts to increase the kinetics while lowering the sorption temperatures. This paper outlines the results of these systematic tests and describes a number of beneficial additions which influence kinetics as well as NH3 formation.

Effect of Copper on Corrosion of Forged AlSi1MgMn Automotive Suspension Components

Science.gov (United States)

Koktas, Serhan; Gokcil, Emre; Akdi, Seracettin; Birol, Yucel

2017-09-01

Recently, modifications in the alloy composition and the manufacturing process cycle were proposed to achieve a more uniform structure with no evidence of coarse grains across the section of the AlSi1MgMn alloys. Cu was added to the AlSi1MgMn alloy to improve its age hardening capacity without a separate solution heat treatment. However, Cu addition degrades the corrosion resistance of this alloy due to the formation of Al-Cu precipitates along the grain boundaries that are cathodic with respect to the aluminum matrix and thus encourage intergranular corrosion. The present work was undertaken to identify the impact of Cu addition on the corrosion properties of AlSi1MgMn alloys with different Cu contents. A series of AlSi1MgMn alloys with 0.06-0.89 wt.% Cu were tested in order to identify an optimum level of Cu addition.

Reduction of hydrogen desorption temperature of ball-milled MgH2 by NbF5 addition

International Nuclear Information System (INIS)

Recham, N.; Bhat, V.V.; Kandavel, M.; Aymard, L.; Tarascon, J.-M.; Rougier, A.

2008-01-01

Enhanced sorption properties of ball-milled MgH 2 are reported by adding NbF 5 . Among various catalyst amounts, 2 mol% of NbF 5 reveals to be the optimum concentration leading to significant reduction of the desorption temperature as well as faster kinetics of ball-milled MgH 2 . At 200 deg. C, temperature at which MgH 2 does not show any activity, MgH 2NbF 5 /2mol% composite desorbs 3.2 wt.% of H 2 in 50 mins. Interestingly, the addition of NbF 5 is also associated with an increase in the desorption pressure. At 300 deg. C, MgH 2NbF 5 /2mol% composite starts to desorb hydrogen at 600 mbar in comparison with 1 mbar for MgH 2 . Further improvements were successfully achieved by pre-grinding NbF 5 prior to ball-milling the catalyst with MgH 2 . Such pre-ground NbF 5 catalyzed MgH 2 composite desorbs 3 wt.% of H 2 at 150 deg. C. Improved properties are associated with smaller activation energies down to values close to the enthalpy of formation of MgH 2 . Finally, the mechanism at the origin of the enhancement is discussed in terms of catalyst stability, MgF 2 formation and electronic density localization

Effect of Nitric and Oxalic Acid Addition on Hard Anodizing of AlCu4Mg1 in Sulphuric Acid

Directory of Open Access Journals (Sweden)

Maximilian Sieber

2018-02-01

Full Text Available The anodic oxidation process is an established means for the improvement of the wear and corrosion resistance of high-strength aluminum alloys. For high-strength aluminum-copper alloys of the 2000 series, both the current efficiency of the anodic oxidation process and the hardness of the oxide coatings are significantly reduced in comparison to unalloyed substrates. With regard to this challenge, recent investigations have indicated a beneficial effect of nitric acid addition to the commonly used sulphuric acid electrolytes both in terms of coating properties and process efficiency. The present work investigates the anodic oxidation of the AlCu4Mg1 alloy in a sulphuric acid electrolyte with additions of nitric acid as well as oxalic acid as a reference in a full-factorial design of experiments (DOE. The effect of the electrolyte composition on process efficiency, coating thickness and hardness is established by using response functions. A mechanism for the participation of the nitric acid additive during the oxide formation is proposed. The statistical significance of the results is assessed by an analysis of variance (ANOVA. Eventually, scratch testing is applied in order to evaluate the failure mechanisms and the abrasion resistance of the obtained conversion coatings.

Additional lime of CaO in rearing medium with salinity for growing of catfish Pangasius hypopthalmus

Directory of Open Access Journals (Sweden)

Yuni Puji Hastuti

2013-11-01

Full Text Available Catfish juvenile quality improvements sought through the addition of lime to the availability of minerals in the body. Media maintenance is set at 4‰ salinity aims to reduce the level of osmotic work to reduce energy used for osmoregulation and can be allocated to the growth of catfish. Juvenile-sized fish used 2.59±0.02 cm and weights 0.13±0.01 g. Aquarium measuring 20×20×20 cm3 used 15 units, filled with water salinity of 4% as 6 L per unit, and added lime CaO appropriate treatment. During the study, the fish were fed with 28% protein content three times a day with FR 5%. Addition of CaO treatment dose 0 mg/L, 20 mg/L, 40 mg/L, 60 mg/L, 80 mg/L result in the survival rate of 100%, 100%, 100%, 96.29%, and 100% (p>0.05. The growth rate of daily weight 5.196%, 5.212%, 6.596%, 5.35% and 5.101% (p>0.05. Long absolute yield significantly different values are 1.451 cm, 1.518 cm, 1.964 cm, 1.71 cm, and 1.546 cm (p<0.05. During the study, the water quality is within the range that can be tolerated by catfish juvenile. The use of lime in the salinity of 4% is suggested as many as 40 mg/L CaO with the turnover of water every day and feeding enough.Keywords: CaO, salinity, growth, Pangasius hypopthalmus

Solid-State Fermentation of Silybum marianum L. Seeds Used as Additive to Increase the Nutritional Value of Wheat Bread

Directory of Open Access Journals (Sweden)

Dalia Cizeikiene

2013-01-01

Full Text Available In the present study Silybum marianum L. seeds were fermented using solid-state fermentation (SSF with several lactic acid bacteria (LAB of Lactobacillus and Pediococcus genera, isolated from spontaneously fermented Lithuanian rye sourdough. A possibility to improve sensory properties (flavour of Silybum marianum L. seeds using LAB fermentation was investigated. The composition of volatile compounds of the unfermented and LAB-fermented seeds of this plant was analyzed using gas chromatography-mass spectrometry (GC-MS. Fermented seeds have shown considerable differences mainly due to the accumulation of higher alcohols. Total amount of phenolic compounds, flavonoids and 2,2-diphenylpicrylhydrazyl (DPPH radical scavenging activity of unfermented and fermented seeds were determined spectrophotometrically. The obtained results indicate that Silybum marianum L. seeds are a valuable source of bioactive compounds. The highest content of phenolic compounds and flavonoids (4596 and 1346 mg of rutin equivalents (RE per 100 g, respectively was determined in the seeds fermented with Pediococcus acidilactici KTU05-7 bacteria in solid-state fermentation. Silybum marianum L. seeds fermented with P. acidilactici KTU05-7 and Pediococcus pentosaceus KTU05-9 showed stronger antioxidant activity (1263 and 1041 mg of RE per 100 g, respectively, compared to the unfermented seeds (805 mg of RE per 100 g. The addition of Silybum marianum L. seeds fermented with P. acidilactici KTU05-7 bacteria had the highest effect on the decrease of the bacterial spoilage of bread. The aroma compounds from the fermented seeds extracted with supercritical carbon dioxide demonstrated the highest antimicrobial activity against the tested microorganisms. Ultrasonic pretreatment of the seeds reduced the total amount of microorganisms in the raw material. Microbiological tests revealed that the highest antimicrobial effect was achieved using the solid-state fermentation conditions. This

Superior critical current density obtained in MgB_2 bulks via employing carbon-coated boron and minor Cu addition

International Nuclear Information System (INIS)

Peng, Junming; Liu, Yongchang; Ma, Zongqing; Shahriar Al Hossain, M.; Xin, Ying; Jin, Jianxun

2016-01-01

Highlights: • Usage of carbon-coated boron leads to high level of homogeneous carbon doping. • Cu addition improves MgB_2 grain connectivity, leading to higher J_c at low fields. • Cu addition reduces MgO impurity, also contributing to the improvement of J_c. - Abstract: High performance Cu doped MgB_2 bulks were prepared by an in-situ method with carbon-coated amorphous boron as precursor. It was found that the usage of carbon-coated boron in present work leads to the formation of uniformly refined MgB_2 grains, as well as a high level of homogeneous carbon doping in the MgB_2 samples, which significantly enhance the J_c in both Cu doped and undoped bulks compared to MgB_2 bulks with normal amorphous boron precursor. Moreover, minor Cu can service as activator, and thus facilitates the growth of MgB_2 grains and improves crystallinity and grain connectivity, which can bring about the excellent critical current density (J_c) at self fields and low fields (the best values are 7 × 10"5 A/cm"2 at self fields, and 1 × 10"5 A/cm"2 at 2 T, 20 K, respectively). Simultaneously, minor Cu addition can reduce the amount of MgO impurity significantly, also contributing to the improvement of J_c at low fields. Our work suggests that Cu-activated sintering combined with employment of carbon-coated amorphous boron as precursor could be a promising technique to produce practical MgB_2 bulks or wires with excellent J_c on an industrial scale.

Ropivacaine 7.5 mg/mL for Caesarean Section

Directory of Open Access Journals (Sweden)

N. K. Nguyen

2010-01-01

Full Text Available Background. Pain after Caesarean delivery is partly related to Pfannenstiel incision, which can be infiltrated with local anaesthetic solutions. Methods. A double- blind randomized control trial was designed to assess the analgesic efficacy of 7.5 mg/mL ropivacaine solution compared to control group, in two groups of one hundred and forty four parturients for each group, who underwent Caesarean section under spinal anaesthesia: group R (ropivacaine group and group C (control group. All parturients also received spinal sufentanil (2.5 g. Results. Ropivacaine infiltration in the Pfannenstiel incision for Caesarean delivery before wound closure leads to a reduction of 30% in the overall consumption of analgesics (348 550 mg for group R versus 504 426 mg for group C with <.05, especially opioids in the first 24 hours, but also significantly increases the time interval until the first request for an analgesic (4 h 20 min ± 2 h 26 for group R versus 2 h 42 ± 1 h 30 for group C. The P values for the two groups were: <.0001 for paracetamol, <.0001 for ketoprofen and P for nalbuphine which was the most significant. There is no significant difference in the threshold of VAS in the two series. Conclusion. This technique can contribute towards a programme of early rehabilitation in sectioned mothers, with earlier discharge from the post-labour suite.

The effect of theobromine 200 mg/l topical gel exposure duration against surface enamel hardness resistance from 1% citric acid

Science.gov (United States)

Herisa, H. M.; Noerdin, A.; Eriwati, Y. K.

2017-08-01

Theobromine can be used to prevent the demineralization of enamel and can stimulate the growth of new enamels. This study analyzes the effect of theobromine’s gel duration exposure on enamel hardness resistance from 1% citric acid. Twenty-eight specimens were divided into three experimental groups; were exposed to theobromine gel 200 mg/l for 16, 48, and 96 minutes; and were then immersed in 1% citric acid. The control group was only immersed in 1% citric acid. Results: A Wilcoxon test showed a significant increase and decrease in enamel microhardness after exposure to theobromine gel and citric acid (p enamel microhardness between different durations of exposure to theobromine gel and immersion in citric acid (p enamel microhardness but did not contribute to the enamel’s hardness resistance after immersion in 1% citric acid. The duration of theobromine gel application affected enamel microhardness and acid resistance.

Simultaneous removal of carbon and nitrogen by mycelial pellets of a heterotrophic nitrifying fungus-Penicillium sp. L1.

Science.gov (United States)

Liu, Yuxiang; Hu, Tingting; Zhao, Jing; Lv, Yongkang; Ren, Ruipeng

2017-02-01

A novel heterotrophic nitrifying fungus, defined as Penicillium sp. L1, can form mycelial pellets in liquid medium in this study. The effects of inoculation method, C/N ratio, initial pH, and temperature were gradually evaluated to improve the simultaneous removal of total nitrogen (TN) and chemical oxygen demand (COD) in wastewater by Penicillium sp. L1. Results showed that compared with spore inoculation, 48 h pellet inoculum could significantly increase the pellet size (from about 1.5 mm to 3.2 mm) and improve the removal capability, particularly for COD removal (from less than 50-86.20%). The removal efficiencies of TN and COD reached 98.38% (from 136.01 mg/L to 2.20 mg/L) and 92.40% (from 10,720 mg/L to 815 mg/L) under the following conditions: C/N 36, pH 3, 30°C, and inoculation with 48 h pellets. The pellet diameter reached 4.8 mm after 4-day cultivation. In this case, Penicillium sp. L1 removed TN from 415.93 mg/L to 43.39 mg/L, as well as COD from 29,533 mg/L to 8850 mg/L. Overall, the results indicated that the pellet size was closely related to the pollutant-removal ability of Penicillium sp. L1. Furthermore, mycelial pellets (4.8 mm, dead) only adsorbed 38.08% TN (from 125.45 mg/L to 77.78 mg/L), which indicated that adsorption did not play a major role in the nitrogen-removal process. Copyright © 2016 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Grain refining mechanism of Al-containing Mg alloys with the addition of Mn-Al alloys

International Nuclear Information System (INIS)

Qin, Gaowu W.; Ren Yuping; Huang Wei; Li Song; Pei Wenli

2010-01-01

Graphical abstract: Display Omitted Research highlights: The ε-AlMn phase acts as the heterogeneous nucleus of α-Mg phase during the solidification of the AZ31 Mg alloy, not the γ-Al 8 Mn 5 phase. The grain refinement effect is very clear with the addition of only 0.5 wt% Mn-28Al alloy (pure ε-AlMn). The grain refinement does not deteriorate up to the holding time of 60 min at 740 o C. - Abstract: The effect of manganese on grain refinement of Al-containing AZ31 Mg alloy has been investigated by designing a series of Mn-Al alloys composed of either pure ε-AlMn, γ 2 -Al 8 Mn 5 or both of them using optical microscopy and X-ray diffraction. It is experimentally clarified that the grain refinement of the AZ31 Mg alloy is due to the existence of the ε-AlMn phase in the Mn-Al alloys, not the γ 2 -Al 8 Mn 5 phase. The grain size of AZ31 Mg alloy is about 91 μm without any addition of Mn-Al alloys, but remarkably decreases to ∼55 μm with the addition of either Mn-34 wt% Al or Mn-28 wt% Al. With a minor addition of 0.5 wt% Mn-28Al alloy, the grain size of AZ31 alloy decreases to ∼53 μm, and the Mn-28Al alloy can be active as grain refiner for holding time up to 60 min for the melt AZ31 alloy at 750 o C.

Concentrations in plasma, epithelial lining fluid, alveolar macrophages and bronchial mucosa after a single intravenous dose of 1.6 mg/kg of iclaprim (AR-100) in healthy men.

Science.gov (United States)

Andrews, J; Honeybourne, D; Ashby, J; Jevons, G; Fraise, A; Fry, P; Warrington, S; Hawser, S; Wise, R

2007-09-01

A validated microbiological assay was used to measure concentrations of iclaprim (AR-100) in plasma, bronchial mucosa (BM), alveolar macrophages (AM) and epithelial lining fluid (ELF) after a single 1.6 mg/kg intravenous 60 min iv infusion of iclaprim. Male volunteers were randomly allocated to three nominal sampling time intervals 1-2 h (Group A), 3-4 h (Group B) and 5.5-7.0 h (Group C) after the start of the drug infusion. Mean iclaprim concentrations in plasma, BM, AM and ELF, respectively, were for Group A 0.59 mg/L (SD 0.18), 0.51 mg/kg (SD 0.17), 24.51 mg/L (SD 21.22) and 12.61 mg/L (SD 7.33); Group B 0.24 mg/L (SD 0.05), 0.35 mg/kg (SD 0.17), 7.16 mg/L (SD 1.91) and 6.38 mg/L (SD 5.17); and Group C 0.14 mg/L (SD 0.05), no detectable level in BM, 5.28 mg/L (SD 2.30) and 2.66 mg/L (SD 2.08). Iclaprim concentrations in ELF and AM exceeded the MIC(90) for penicillin-susceptible Streptococcus pneumoniae (MIC90 0.06 mg/L), penicillin-intermediate S. pneumoniae (MIC90 2 mg/L), penicillin-resistant S. pneumoniae (MIC90 4 mg/L) for 7, 7 and 4 h, respectively, and Chlamydia pneumoniae (MIC90 0.5 mg/L) for 7 h. Mean iclaprim concentrations in ELF exceeded the MIC90 for Haemophilus influenzae (MIC90 4 mg/L) and Moraxella catarrhalis (MIC90 8 mg/L) for up to 4 and 2 h, respectively; in AM the MIC90 was exceeded for up to 7 h. Furthermore, the MIC90 for methicillin-resistant Staphylococcus aureus of 0.12 mg/L was exceeded at all sites for up to 7 h. These data suggest that iclaprim reaches lung concentrations that should be effective in the treatment of community-acquired pneumonia.

Anaerobic digestion of Jatropha curcas L. press cake and effects of an iron-additive.

Science.gov (United States)

Schmidt, Thomas

2011-11-01

Oil production from Jatropha curcas L. seeds generates large amounts of Jatropha press cake (JPC) which can be utilized as a substrate for biogas production. The objective of this work was to investigate anaerobic mono-digestion of JPC and the effects of an iron additive (IA) on gas quality and process stability during the increase of the organic loading rate (OLR). With the increase of the OLR from 1.3 to 3.2 g(VS) L(-1) day(-1), the biogas yield in the reference reactor (RR) without IA decreased from 512 to 194 L(N) kg(VS) (-1) and the CH₄ concentration decreased from 69.3 to 44.4%. In the iron additive reactor (IAR), the biogas yield decreased from 530 to 462 L(N) kg(VS) (-1) and the CH₄ concentration decreased from 69.4 to 61.1%. The H₂S concentration in the biogas was reduced by addition of the IA to values below 258 ppm in the IAR while H₂S concentration in the RR increased and exceeded the detection limit of 5000 ppm. The acid capacity (AC) in the RR increased to more than 20 g L(-1), indicating an accumulation of organic acids caused by process instability. AC values in the IAR remained stable at values below 5 g L(-1). The results demonstrate that JPC can be used as sole substrate for anaerobic digestion up to an OLR of 2.4 g(VS) l(-1) day(-1). The addition of IA has effectively decreased the H(2)S content in the biogas and has improved the stability of the anaerobic process and the biogas quality.

Influence of elemental diffusion on low temperature formation of MgH2 in TiMn1.3T0.2-Mg (T = 3d-transition elements)

International Nuclear Information System (INIS)

Yamamoto, K.; Tanioka, S.; Tsushio, Y.; Shimizu, T.; Morishita, T.; Orimo, S.; Fujii, H.

1996-01-01

In order to examine the influence of the elemental diffusion from the host compound into the Mg region on low temperature formation of MgH 2 , we have investigated the hydriding properties and the microstructures of the composite materials TiMn 1.3 T 0.2 -Mg (T = V, Cr, Mn, Fe, Co, Ni and Cu). MgH 2 is formed at 353 K in all composite materials. Of all the substitutions, the amount of MgH 2 is the largest in the case of the Cu substitution, which originates from the existence of the Mg-Mg 2 Cu eutectic formed by Cu diffusion from the host compound TiMn 1.3 Cu 0.2 into the Mg region during the liquid phase sintering. In addition, the hydrogen capacity of TiMn 1.3 Cu 0.2 -Mg (that is TiMn 1.3 Cu 0.1 -(Mg+Mg 2 Cu) after the sintering) easily saturates in comparison with TiMn 1.5 -(Mg+Mg 2 Cu) without Cu diffusion. It is concluded that Cu diffusion promotes the mobility of hydrogen atoms at the complex interface between the host compound and the Mg region. (orig.)

Mg2BIV: Narrow Bandgap Thermoelectric Semiconductors

Science.gov (United States)

Kim, Il-Ho

2018-05-01

Thermoelectric materials can convert thermal energy directly into electric energy and vice versa. The electricity generation from waste heat via thermoelectric devices can be considered as a new energy source. For instance, automotive exhaust gas and all industrial processes generate an enormous amount of waste heat that can be converted to electricity by using thermoelectric devices. Magnesium compound Mg2BIV (BIV = Si, Ge or Sn) has a favorable combination of physical and chemical properties and can be a good base for the development of new efficient thermoelectrics. Because they possess similar properties to those of group BIV elemental semiconductors, they have been recognized as good candidates for thermoelectric applications. Mg2Si, Mg2Ge and Mg2Sn with an antifluorite structure are narrow bandgap semiconductors with indirect band gaps of 0.77 eV, 0.74 eV, and 0.35 eV, respectively. Mg2BIV has been recognized as a promising material for thermoelectric energy conversion at temperatures ranging from 500 K to 800 K. Compared to other thermoelectric materials operating in the similar temperature range, such as PbTe and filled skutterudites, the important aspects of Mg2BIV are non-toxic and earth-abundant elements. Based on classical thermoelectric theory, the material factor β ( m* / m e)3/2μκ L -1 can be utilized as the criterion for thermoelectric material selection, where m* is the density-of-states effective mass, me is the mass of an electron, μ is the carrier mobility, and κL is the lattice thermal conductivity. The β for magnesium silicides is 14, which is very high compared to 0.8 for iron silicides, 1.4 for manganese silicides, and 2.6 for silicon-germanium alloys. In this paper, basic phenomena of thermoelectricity and transport parameters for thermoelectric materials were briefly introduced, and thermoelectric properties of Mg2BIV synthesized by using a solid-state reaction were reviewed. In addition, various Mg2BIV compounds were discussed

Grain refining mechanism of Al-containing Mg alloys with the addition of Mn-Al alloys

Energy Technology Data Exchange (ETDEWEB)

Qin, Gaowu W., E-mail: qingw@smm.neu.edu.c [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), Northeastern University, Wenhu Road 3-11, Heping District, Shenyang 110004, Liaoning Province (China); Ren Yuping; Huang Wei; Li Song; Pei Wenli [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), Northeastern University, Wenhu Road 3-11, Heping District, Shenyang 110004, Liaoning Province (China)

2010-10-08

Graphical abstract: Display Omitted Research highlights: The {epsilon}-AlMn phase acts as the heterogeneous nucleus of {alpha}-Mg phase during the solidification of the AZ31 Mg alloy, not the {gamma}-Al{sub 8}Mn{sub 5} phase. The grain refinement effect is very clear with the addition of only 0.5 wt% Mn-28Al alloy (pure {epsilon}-AlMn). The grain refinement does not deteriorate up to the holding time of 60 min at 740 {sup o}C. - Abstract: The effect of manganese on grain refinement of Al-containing AZ31 Mg alloy has been investigated by designing a series of Mn-Al alloys composed of either pure {epsilon}-AlMn, {gamma}{sub 2}-Al{sub 8}Mn{sub 5} or both of them using optical microscopy and X-ray diffraction. It is experimentally clarified that the grain refinement of the AZ31 Mg alloy is due to the existence of the {epsilon}-AlMn phase in the Mn-Al alloys, not the {gamma}{sub 2}-Al{sub 8}Mn{sub 5} phase. The grain size of AZ31 Mg alloy is about 91 {mu}m without any addition of Mn-Al alloys, but remarkably decreases to {approx}55 {mu}m with the addition of either Mn-34 wt% Al or Mn-28 wt% Al. With a minor addition of 0.5 wt% Mn-28Al alloy, the grain size of AZ31 alloy decreases to {approx}53 {mu}m, and the Mn-28Al alloy can be active as grain refiner for holding time up to 60 min for the melt AZ31 alloy at 750 {sup o}C.

Effects of Ni-5%RExOy Composite Additives on Electrochemical Hydrogen Storage Performances of Mg2Ni

Directory of Open Access Journals (Sweden)

ZHANG Guo-fang

2017-11-01

Full Text Available The Ni-5%RExOy (CeO2, La2O3, Eu2O3 as composite additives, Mg2Ni-Ni-5%RExOy composites were prepared by the ball milling method. The effects of different additives on the structure, morphology, electrochemistry and kinetic properties of Mg2Ni alloy were studied systematically. The results show that composite additives can improve the proportion of amorphous and nanocrystalline structure of Mg2Ni alloy. The particle size is homogeneous but the agglomeration is observed in the sample with Ni-5%CeO2 additives. The composites with additives show higher maximum discharge capacity and better cycle stabilities. All of these three kinds of composite additives can improve the kinetic properties of the composites effectively, including optimizing the charge-transfer ability, the reversibility of the electrochemical reaction on the alloy surface, and enhancing the diffusion coefficients of H atoms in the bulk of alloy. Among these three kinds of additives, Ni-5%CeO2 additive shows the best catalysis effect on promoting the kinetic properties of the composites.

A combined toxicity study of zinc oxide nanoparticles and vitamin C in food additives.

Science.gov (United States)

Wang, Yanli; Yuan, Lulu; Yao, Chenjie; Ding, Lin; Li, Chenchen; Fang, Jie; Sui, Keke; Liu, Yuanfang; Wu, Minghong

2014-12-21

At present, safety evaluation standards for nanofood additives are made based on the toxic effects of a single additive. Since the size, surface properties and chemical nature influence the toxicity of nanomaterials, the toxicity may have dramatically changed when nanomaterials are used as food additives in a complex system. Herein, we investigated the combined toxicity of zinc oxide nanoparticles (ZnO NPs) and vitamin C (Vc, ascorbic acid). The results showed that Vc increased the cytotoxicity significantly compared with that of the ZnO only NPs. When the cells were exposed to ZnO NPs at a concentration less than 15 mg L(-1), or to Vc at a concentration less than 300 mg L(-1), there was no significant cytotoxicity, both in the case of gastric epithelial cell line (GES-1) and neural stem cells (NSCs). However, when 15 mg L(-1) of ZnO NPs and 300 mg L(-1) of Vc were introduced to cells together, the cell viability decreased sharply indicating significant cytotoxicity. Moreover, the significant increase in toxicity was also shown in the in vivo experiments. The dose of the ZnO NPs and Vc used in the in vivo study was calculated according to the state of food and nutrition enhancer standard. After repeated oral exposure to ZnO NPs plus Vc, the injury of the liver and kidneys in mice has been indicated by the change of these indices. These findings demonstrate that the synergistic toxicity presented in a complex system is essential for the toxicological evaluation and safety assessment of nanofood.

Effect of Mg/Ca ratios on microbially induced carbonate precipitation

Science.gov (United States)

Balci, Nurgul; Demirel, Cansu; Seref Sonmez, M.; Kurt, M. Ali

2016-04-01

Influence of Mg/Ca ratios on microbially induced carbonate mineralogy were investigated by series of experiments carried out under various environmental conditions (Mg/Ca ratio, temperature and salinity). Halophilic bacterial cultures used for biomineralization experiments were isolated from hypersaline Lake Acıgöl (Denizli, SW Turkey), displaying extreme water chemistry with an average pH around 8.6 (Balci eta l.,2015). Enriched bacterial culture used in the experiments consisted of Halomonas saccharevitans strain AJ275, Halomonas alimentaria strain L7B; Idiomarina sp. TBZ29, 98% Idiomarina seosensis strain CL-SP19. Biomineralization experiments were set up using above enriched culture with Mg/Ca ratios of 0.05, 1, 4 and 15 and salinity of 8% and 15% experiments at 30oC and 10oC. Additionally, long-term biomineralization experiments were set up to last for a year, for Mg/Ca=4 and Mg/Ca=15 experiments at 30oC. For each experimental condition abiotic experiments were also conducted. Solution chemistry throughout incubation was monitored for Na, K, Mg, Ca, bicarbonate, carbonate, ammonium and phosphate for a month. At the end of the experiments, precipitates were collected and morphology and mineralogy of the biominerals were investigated and results were evaluated using the software DIFFRAC.SUITE EVA. Overall the preliminary results showed chemical precipitation of calcite, halite, hydromagnesite and sylvite. Results obtained from biological experiments indicate that, low Mg/Ca ratios (0.05 and 1) favor chlorapatite precipitation, whereas higher Mg/Ca ratios favor struvite precipitation. Biomineralization of dolomite, huntite and magnesite is favorable at high Mg/Ca ratios (4 and 15), in the presence of halophilic bacteria. Moreover, results indicate that supersaturation with respect to Mg (Mg/Ca=15) combined with NaCl (15%) inhibits biomineralization and forms chemical precipitates. 15% salinity is shown to favor chemical precipitation of mineral phases more than

Critical current density improvements in MgB2 superconducting bulk samples by K2CO3 additions  

DEFF Research Database (Denmark)

Grivel, J.-C.

2018-01-01

MgB2 bulk samples with potassium carbonate doping were made by means of reaction of elemental Mg and B powders mixed with various amounts of K2CO3. The Tc of the superconducting phase as well as its a-axis parameter were decreased as a result of carbon doping. Potassium escaped the samples during...... reaction. The critical current density of MgB2 was improved both in self field and under applied magnetic field for T ≤ 30 K, with optimum results for 1 mol% K2CO3 addition. The normalized flux pinning force (f(b)) shows that the flux pinning mechanism at low field is similar for all samples, following...

Superior critical current density obtained in MgB{sub 2} bulks via employing carbon-coated boron and minor Cu addition

Energy Technology Data Exchange (ETDEWEB)

Peng, Junming; Liu, Yongchang [State Key Laboratory of Hydraulic Engineering Simulation and Safety, School of Materials Science & Engineering, Tianjin University, Tianjin 300072 (China); Ma, Zongqing, E-mail: mzq0320@163.com [State Key Laboratory of Hydraulic Engineering Simulation and Safety, School of Materials Science & Engineering, Tianjin University, Tianjin 300072 (China); Institute for Superconducting and Electronic Materials, AIIM, University of Wollongong, Squires Way, North Wollongong, NSW 2500 (Australia); Shahriar Al Hossain, M. [Institute for Superconducting and Electronic Materials, AIIM, University of Wollongong, Squires Way, North Wollongong, NSW 2500 (Australia); Xin, Ying; Jin, Jianxun [Tianjin University – Futong Group Research Center of Applied Superconductivity, Tianjin University, Tianjin 300072 (China)

2016-09-15

Highlights: • Usage of carbon-coated boron leads to high level of homogeneous carbon doping. • Cu addition improves MgB{sub 2} grain connectivity, leading to higher J{sub c} at low fields. • Cu addition reduces MgO impurity, also contributing to the improvement of J{sub c}. - Abstract: High performance Cu doped MgB{sub 2} bulks were prepared by an in-situ method with carbon-coated amorphous boron as precursor. It was found that the usage of carbon-coated boron in present work leads to the formation of uniformly refined MgB{sub 2} grains, as well as a high level of homogeneous carbon doping in the MgB{sub 2} samples, which significantly enhance the J{sub c} in both Cu doped and undoped bulks compared to MgB{sub 2} bulks with normal amorphous boron precursor. Moreover, minor Cu can service as activator, and thus facilitates the growth of MgB{sub 2} grains and improves crystallinity and grain connectivity, which can bring about the excellent critical current density (J{sub c}) at self fields and low fields (the best values are 7 × 10{sup 5} A/cm{sup 2} at self fields, and 1 × 10{sup 5} A/cm{sup 2} at 2 T, 20 K, respectively). Simultaneously, minor Cu addition can reduce the amount of MgO impurity significantly, also contributing to the improvement of J{sub c} at low fields. Our work suggests that Cu-activated sintering combined with employment of carbon-coated amorphous boron as precursor could be a promising technique to produce practical MgB{sub 2} bulks or wires with excellent J{sub c} on an industrial scale.

Characteristics and corrosion studies of vanadate conversion coating formed on Mg-14 wt%Li-1 wt%Al-0.1 wt%Ce alloy

Energy Technology Data Exchange (ETDEWEB)

Ma Yibin [School of Chemical Engineering and Technology, Harbin Institute of Technology, Harbin 150001 (China); Li Ning, E-mail: lininghit@263.net [School of Chemical Engineering and Technology, Harbin Institute of Technology, Harbin 150001 (China); Li Deyu [School of Chemical Engineering and Technology, Harbin Institute of Technology, Harbin 150001 (China); Zhang Milin; Huang Xiaomei [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin Engineering University, Harbin 150001 (China)

2012-11-15

Highlights: Black-Right-Pointing-Pointer Vanadate film forms on the surface of Mg-Li-Al-Ce alloy. Black-Right-Pointing-Pointer Vanadate coating improves the corrosion resistance. Black-Right-Pointing-Pointer Vanadate coating is composed of Mg(OH){sub 2}, Li{sub 2}O and V{sub 2}O{sub 5}. - Abstract: Mg-14Li-1Al-0.1Ce alloy is immersed in NH{sub 4}VO{sub 3} + K{sub 3}(Fe(CN){sub 6}) solutions with different NH{sub 4}VO{sub 3} and/or K{sub 3}(Fe(CN){sub 6}) concentrations, and different immersion time. The surface morphology and composition of the vanadate coating are then characterized by scanning electron microscopy with energy dispersion spectroscopy (SEM-EDS) and X-ray photoelectron spectroscopy (XPS), and the corrosion behavior of the conversion coating is studied by polarization technique and electrochemical impedance spectroscopy (EIS). The experimental results indicate that the vanadate film with better corrosion resistance forms on Mg-Li-Al-Ce surface after the sample is immersed in 30 g L{sup -1} NH{sub 4}VO{sub 3} + 3.75 g L{sup -1} K{sub 3}(Fe(CN){sub 6}) solution at 80 Degree-Sign C for 10 min. The coating consists of V{sub 2}O{sub 5}, Li{sub 2}O and Mg(OH){sub 2}.

PD-L1-specific T cells

DEFF Research Database (Denmark)

Ahmad, Shamaila Munir; Borch, Troels Holz; Hansen, Morten

2016-01-01

-specific T cells that recognize both PD-L1-expressing immune cells and malignant cells. Thus, PD-L1-specific T cells have the ability to modulate adaptive immune reactions by reacting to regulatory cells. Thus, utilization of PD-L1-derived T cell epitopes may represent an attractive vaccination strategy...... for targeting the tumor microenvironment and for boosting the clinical effects of additional anticancer immunotherapy. This review summarizes present information about PD-L1 as a T cell antigen, depicts the initial findings about the function of PD-L1-specific T cells in the adjustment of immune responses...

Efficient callus formation and plant regeneration of goosegrass [Eleusine indica (L.) Gaertn.].

Science.gov (United States)

Yemets, A I; Klimkina, L A; Tarassenko, L V; Blume, Y B

2003-02-01

Efficient methods in totipotent callus formation, cell suspension culture establishment and whole-plant regeneration have been developed for the goosegrass [ Eleusine indica (L.) Gaertn.] and its dinitroaniline-resistant biotypes. The optimum medium for inducing morphogenic calli consisted of N6 basal salts and B5 vitamins supplemented with 1-2 mg l(-1) 2,4-dichlorophenoxyacetic acid (2,4-D), 2 mg l(-1) glycine, 100 mg l(-1) asparagine, 100 mg l(-1) casein hydrolysate, 30 g l(-1) sucrose and 0.6% agar, pH 5.7. The presence of organogenic and embryogenic structures in these calli was histologically documented. Cell suspension cultures derived from young calli were established in a liquid medium with the same composition. Morphogenic structures of direct shoots and somatic embryos were grown into rooted plantlets on medium containing MS basal salts, B5 vitamins, 1 mg l(-1) kinetin (Kn) and 0.1 mg l(-1) indole-3-acetic acid (IAA), 3% sucrose, 0.6% agar, pH 5.7. Calli derived from the R-biotype of E. indica possessed a high resistance to trifluralin (dinitroaniline herbicide) and cross-resistance to a structurally non-related herbicide, amiprophosmethyl (phosphorothioamidate herbicide), as did the original resistant plants. Embryogenic cell suspension culture was a better source of E. indica protoplasts than callus or mesophyll tissue. The enzyme solution containing 1.5% cellulase Onozuka R-10, 0.5% driselase, 1% pectolyase Y-23, 0.5% hemicellulase and N(6) mineral salts with an additional 0.2 M KCl and 0.1 M CaCl(2) (pH 5.4-5.5) was used for protoplast isolation. The purified protoplasts were cultivated in KM8p liquid medium supplemented with 2 mg l(-1) 2,4-D and 0.2 mg l(-1) Kn.

Development of novel quinoa-based yoghurt fermented with dextran producer Weissella cibaria MG1.

Science.gov (United States)

Zannini, Emanuele; Jeske, Stephanie; Lynch, Kieran M; Arendt, Elke K

2018-03-02

The aim of this study was to develop a novel beverage fermented with Weissella cibaria MG1 based on aqueous extracts of wholemeal quinoa flour. The protein digestibility of quinoa based-milk was improved by applying complex proteolytic enzymes able to increase protein solubility by 54.58%. The growth and fermentation characteristics of Weissella cibaria MG1, including EPS production at the end of fermentation, were investigated. Fermented wholemeal quinoa milk using MG1 showed high viable cell counts (>10 9 cfu/ml), a pH of 5.16, and significantly higher water holding capacity (WHC, 100%), viscosity (0.57mPas) and exopolysaccharide (EPS) amount (40mg/l) than the chemical acidified control. High EPS (dextran) concentration in quinoa milk caused earlier aggregation because more EPS occupy more space, and the chenopodin were forced to interact with each other. Microstructure observation indicated that the network structures of EPS-protein improve the texture of fermented quinoa milk. Overall, Weissella cibaria MG1 showed satisfactory technology properties and great potential for further possible application in the development of high viscosity fermented quinoa milk. Copyright © 2018 Elsevier B.V. All rights reserved.

Influence of Rare Earth Elements on Microstructure and Mechanical Properties of Mg{sub 97}Zn{sub 1}Y{sub 1}RE{sub 1} Alloys

Energy Technology Data Exchange (ETDEWEB)

Kim, Jonghyun, E-mail: joindoc@kumamoto-u.ac.jp [Department of Material Science, Magnesium Research Center (MRC), Kumamoto University, Kumamoto, 860-8555 (Japan); Kawamura, Y. [Department of Material Science, Magnesium Research Center (MRC), Kumamoto University, Kumamoto, 860-8555 (Japan)

2013-06-20

Mg{sub 97}Zn{sub 1}Y{sub 1}RE{sub 1} (RE=La, Ce, Nd and Sm, at. %) alloys were prepared by high-frequency induction melting in an Ar atmosphere. Rods were extruded at 623 K and a ram speed of 2.5 mm·s{sup −1} using a circular die with an extrusion ratio of 10. The microstructure and mechanical properties of the extruded alloys were investigated. The Mg{sub 97}Zn{sub 1}Y{sub 1}Nd{sub 1} and Mg{sub 97}Zn{sub 1}Y{sub 1}Sm{sub 1} alloys consisted of only two phases: α-Mg and a Mg-RE intermetallic compound. The Mg{sub 97}Zn{sub 1}Y{sub 1}La{sub 1} and Mg{sub 97}Zn{sub 1}Y{sub 1}Ce{sub 1} alloys consisted of three phases: α-Mg, a Mg-RE intermetallic compound, and a Mg{sub 12}ZnY phase with a long-period stacking ordered (LPSO) phase. Additionally, after extrusion, the three-phase Mg{sub 97}Zn{sub 1}Y{sub 1}RE{sub 1} alloys, i.e., those with an LPSO phase, had a stratified microstructure and exhibited better mechanical properties than those without an LPSO. At room temperature, the yield strength and ultimate tensile strength of the three-phase Mg{sub 97}Zn{sub 1}Y{sub 1}La{sub 1} and Mg{sub 97}Zn{sub 1}Y{sub 1}Ce{sub 1} alloys were 381–384 MPa and 427–429 MPa, respectively, and yield strengths greater than 280 MPa were observed at the elevated temperature of 523 K.

Preliminary study of the characteristics of a high Mg containing Al-Mg-Si alloy

International Nuclear Information System (INIS)

Yan, F; McKay, B J; Fan, Z; Chen, M F

2012-01-01

An Al-20Mg-4Si high Mg containing alloy has been produced and its characteristics investigated. The as-cast alloy revealed primary Mg 2 Si particles evenly distributed throughout an α-Al matrix with a β-Al 3 Mg 2 fully divorced eutectic phase observed in interdendritic regions. The Mg 2 Si particles displayed octahedral, truncated octahedral, and hopper morphologies. Additions of Sb, Ti and Zr had a refining influence reducing the size of the Mg 2 Si from 52 ± 4 μm to 25 ± 0.1 μm, 35 ± 1 μm and 34 ± 1 μm respectively. HPDC tensile test samples could be produced with a 0.6 wt.% Mn addition which prevented die soldering. Solution heating for 1 hr was found to dissolve the majority of the Al 3 Mg 2 eutectic phase with no evidence of any effect on the primary Mg 2 Si. Preliminary results indicate that the heat treatment has a beneficial effect on the elongation and the UTS.

Isopiestic investigation of the osmotic coefficients of MgBr{sub 2}(aq) and study of bromide salts solubility in the (m{sub 1}KBr + m{sub 2}MgBr{sub 2})(aq) system at T = 323.15 K. Thermodynamic model of solution behaviour and (solid + liquid) equilibria in the MgBr{sub 2}(aq), and (m{sub 1}KBr + m{sub 2}MgBr{sub 2})(aq) systems to high concentration and temperature

Energy Technology Data Exchange (ETDEWEB)

Christov, Christomir, E-mail: christov@svr.igic.bas.b [Institute of General and Inorganic Chemistry, Bulgarian Academy of Sciences, ul. ' Acad. G. Bonchev' , bl. 11, 1113 Sofia (Bulgaria)

2011-03-15

The isopiestic method has been used to determine the osmotic coefficients of the binary solutions MgBr{sub 2}(aq) (from 0.4950 to 2.5197 mol {center_dot} kg{sup -1}) at the temperature T = 323.15 K. Sodium chloride solutions have been used as isopiestic reference standards. The solubility of the bromide minerals in the mixed system (m{sub 1}KBr + m{sub 2}MgBr{sub 2})(aq) has been investigated at T = 323.15 K by the physico-chemical analysis method. In addition to simple salts {l_brace}KBr(cr) and MgBr{sub 2} . 6H{sub 2}O(cr){r_brace}, equilibrium crystallization of the highly incongruent double salt with stoichiometric composition 1:1:6 {l_brace}bromcarnallite: KBr . MgBr{sub 2} . 6H{sub 2}O(cr){r_brace} was also established. The results obtained from the isopiestic and solubility measurements have been combined with all other experimental thermodynamic quantities available in the literature (osmotic coefficients, and solubility of the bromide mineral) to construct a chemical model that calculates solute and solvent activities and (solid + liquid) equilibria in the MgBr{sub 2}(aq) binary, and (m{sub 1}KBr + m{sub 2}MgBr{sub 2})(aq) mixed systems from dilute to high solution concentration within the (273.15 to 438.15) K temperature range. The solubility modelling approach based on fundamental Pitzer specific interaction equations is employed. It was found, that the standard for 2-1 type of electrolytes approach with three ({beta}{sup (0)}, {beta}{sup (1)}, and C{sup {phi}}) single electrolyte ion interaction parameters gives excellent agreement with osmotic coefficients from T = (298.15 to 373.45) K; up to saturation at 298.15 K, and up to m(MgBr{sub 2}) = 5.83 mol {center_dot} kg{sup -1} at 373.45 K, and with MgBr{sub 2} {center_dot} 6H{sub 2}O(cr) equilibrium pure water solubility data within the (273.15 to 438.15) K temperature range and up to {approx}8.5 mol {center_dot} kg{sup -1} used in parameterization. The model for the ternary system gives very good

Aminocarminic acid in E120-labelled food additives and beverages.

Science.gov (United States)

Sabatino, Leonardo; Scordino, Monica; Gargano, Maria; Lazzaro, Francesco; Borzì, Marco A; Traulo, Pasqualino; Gagliano, Giacomo

2012-01-01

An analytical method was developed for investigating aminocarminic acid occurrence in E120-labelled red-coloured-beverages and in E120 additives, with the aim of controlling the purity of the carmine additive in countries where the use of aminocarminic acid is forbidden. The carminic acid and the aminocarminic acid were separated by high-performance liquid chromatography-photodiode array-tandem mass spectrography (HPLC-PDA-MS/MS). The method was statistically validated. The regression lines, ranging from 10 to 100 mg/L, showed r(2 )> 0.9996. Recoveries from 97% to 101% were obtained for the fortification level of 50 mg/L; the relative standard deviations did not exceed 3%. The LODs were below 2 mg/L, whereas the LOQs did not exceed 4 mg/L. The method was successfully applied to 27 samples of commercial E120-labelled red-coloured beverages and E120 additives, collected in Italy during quality control investigations conducted by the Ministry. The results demonstrated that more than 50% of the samples contained aminocarminic acid, evidencing the alarming illicit use of this semi-synthetic carmine acid derivative.

Formation process of micro arc oxidation coatings obtained in a sodium phytate containing solution with and without CaCO{sub 3} on binary Mg-1.0Ca alloy

Energy Technology Data Exchange (ETDEWEB)

Zhang, R.F. [School of Material and Electromechanics, Jiangxi Science and Technology Normal University, Nanchang 330013 (China); Zhang, Y.Q. [Zhejiang DunAn Light Alloy Technology CO,.LTD, Zhuji 311835 (China); Hunan University of Science and Technology, Xiangtan 411201 (China); Zhang, S.F.; Qu, B. [School of Material and Electromechanics, Jiangxi Science and Technology Normal University, Nanchang 330013 (China); Guo, S.B. [Hunan University of Science and Technology, Xiangtan 411201 (China); Xiang, J.H., E-mail: xiangjunhuai@163.com [School of Material and Electromechanics, Jiangxi Science and Technology Normal University, Nanchang 330013 (China)

2015-01-15

Highlights: • Compared to the Mg phase, the area of Mg{sub 2}Ca phase is much smaller. • The coatings are preferentially developed on the area adjacent to Mg{sub 2}Ca phase. • During MAO process, some sodium phytate molecules are hydrolyzed. • Anodic coatings are developed from uneven to uniform. - Abstract: Micro arc oxidation (MAO) is an effective method to improve the corrosion resistance of magnesium alloys. In order to reveal the influence of alloying element Ca and CaCO{sub 3} electrolyte on the formation process and chemical compositions of MAO coatings on binary Mg-1.0Ca alloy, anodic coatings after different anodizing times were prepared on binary Mg-1.0Ca alloy in a base solution containing 3 g/L sodium hydroxide and 15 g/L sodium phytate with and without addition of CaCO{sub 3}. The coating formation was studied by using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). The results show that Mg-1.0Ca alloy is composed of two phases, the Mg phase and Mg{sub 2}Ca phase. After treating for 5 s, the coating began to develop and was preferentially formed on the area nearby Mg{sub 2}Ca phase, which may be resulted from the intrinsic electronegative potential of the Mg phase than that of Mg{sub 2}Ca phase. Anodic coatings unevenly covered the total surface after 20 s. After 80 s, the coatings were uniformly developed on Mg-1.0Ca alloy with micro pores. During MAO process, some sodium phytate molecules are hydrolyzed into inorganic phosphate. CaCO{sub 3} has minor influence on the calcium content of the obtained MAO coatings.

Effects of Cu and Ag additions on age-hardening behavior during multi-step aging in Al--Mg--Si alloys

International Nuclear Information System (INIS)

Kim, JaeHwang; Daniel Marioara, Calin; Holmestad, Randi; Kobayashi, Equo; Sato, Tatsuo

2013-01-01

Low Cu and Ag additions (≤0.10 at%) were found to strongly affect the age-hardening behavior in Al--Mg--Si alloys with Mg+Si>1.5 at%. The hardness increased during aging at 170 °C and the formation of β ″ precipitates was kinetically accelerated. The activation energy of the formation of the β ″ phase was calculated to 127, 105, 108 and 99 KJmol −1 in the base, Cu-added, Ag-added and Cu--Ag-added alloys, respectively using the Kissinger method. The negative effect of two-step aging caused by the formation of Cluster (1) during natural aging was not overcome by the addition of microalloying elements. However, it was suppressed by the formation of Cluster (2) through a pre-aging at 100 °C. Quantitative analysis of the precipitate microstructure was performed using a transmission electron microscope equipped with a parallel electron energy loss spectrometer for the determination of specimen thickness. The formation of Cluster (2) was found to increase the number density of β ″ precipitates, whereas the formation of Cluster (1) decreased the number density and increased the needle length. The effects of low Cu and Ag additions in combination with multi-step aging are discussed based on microstructure observations and hardness and resistivity measurements.

Structure and stacking faults in layered Mg-Zn-Y alloys: A first-principles study

International Nuclear Information System (INIS)

Datta, Aditi; Waghmare, U.V.; Ramamurty, U.

2008-01-01

We use first-principles density functional theory total energy calculations based on pseudo-potentials and plane-wave basis to assess stability of the periodic structures with different stacking sequences in Mg-Zn-Y alloys. For pure Mg, we find that the 6-layer (6l) structure with the ABACAB stacking is most stable after the lowest energy hcp (2l) structure with ABAB stacking. Addition of 2 at.% Y leads to stabilization of the structure to 6l sequence whereas the addition of 2 at.% Zn makes the 6l energetically comparable to that of the hcp. Stacking fault (SF) on the basal plane of 6l structure is higher in energy than that of the hcp 2l Mg, which further increases upon Y doping and decreases significantly with Zn doping. SF energy surface for the prismatic slip indicates activation of non-basal slip in alloys with a 6l structure. Charge density analysis shows that the 2l and 6l structures are electronically similar which might be a cause for better stability of 6l structure over a 4l sequence or other periodic structures. Thus, in an Mg-Zn-Y alloy, Y stabilizes the long periodicity, while its mechanical properties are further improved due to Zn doping

Improving High-Temperature Tensile and Low-Cycle Fatigue Behavior of Al-Si-Cu-Mg Alloys Through Micro-additions of Ti, V, and Zr

Science.gov (United States)

Shaha, S. K.; Czerwinski, F.; Kasprzak, W.; Friedman, J.; Chen, D. L.

2015-07-01

High-temperature tensile and low-cycle fatigue tests were performed to assess the influence of micro-additions of Ti, V, and Zr on the improvement of the Al-7Si-1Cu-0.5Mg (wt pct) alloy in the as-cast condition. Addition of transition metals led to modification of microstructure where in addition to conventional phases present in the Al-7Si-1Cu-0.5Mg base, new thermally stable micro-sized Zr-Ti-V-rich phases Al21.4Si4.1Ti3.5VZr3.9, Al6.7Si1.2TiZr1.8, Al2.8Si3.8V1.6Zr, and Al5.1Si35.4Ti1.6Zr5.7Fe were formed. The tensile tests showed that with increasing test temperature from 298 K to 673 K (25 °C to 400 °C), the yield stress and tensile strength of the present studied alloy decreased from 161 to 84 MPa and from 261 to 102 MPa, respectively. Also, the studied alloy exhibited 18, 12, and 5 pct higher tensile strength than the alloy A356, 354 and existing Al-Si-Cu-Mg alloy modified with additions of Zr, Ti, and Ni, respectively. The fatigue life of the studied alloy was substantially longer than those of the reference alloys A356 and the same Al-7Si-1Cu-0.5Mg base with minor additions of V, Zr, and Ti in the T6 condition. Fractographic analysis after tensile tests revealed that at the lower temperature up to 473 K (200 °C), the cleavage-type brittle fracture for the precipitates and ductile fracture for the matrix were dominant while at higher temperature fully ductile-type fracture with debonding and pull-out of cracked particles was identified. It is believed that the intermetallic precipitates containing Zr, Ti, and V improve the alloy performance at increased temperatures.

Effect on strength of ternary alloying additions in L12 intermetallics

International Nuclear Information System (INIS)

Wu Yuanpang.

1991-01-01

The thermodynamic properties of {111} antiphase boundaries (APBs) as well as the site preference of ternary additions in an A 3 B intermetallic with L1 2 structure are studied, using a thermodynamic model. A survey of the results from a variety of ternary alloying additions to Ni 3 Al has shown that there is a conflict in the actual role which solid solution strengthening plays in the athermal increment of yield strength. For instance, a good quantitative agreement with linear concentration law is observed only in alloys with stoichiometric compositions but not in the general case of non-stoichiometric alloys. In the light of the possibility that micro-segregation could explain the experimental discrepancy, the author extends the binary solid solution strengthening theory to the ternary system in an L1 2 structure for the four real systems of Ni-Al-Si, Ni-Al-Ti, Ni-Al-Hf, and Ni-Al-V. It is found that ternary site preference plays an important role in the ternary solid solution strengthening theory with L1 2 structure. Good quantitative agreement was found between the calculated and experimentally measured strength for both stoichiometric and nonstoichiometric alloys

Enhancement of methyl tert-butyl ether degradation by the addition of readily metabolizable organic substrates

International Nuclear Information System (INIS)

Chen Dongzhi; Chen Jianmeng; Zhong Weihong

2009-01-01

Supplements with readily metabolizable organic substrates were investigated to increase the biomass and enhance degradation of methyl tert-butyl ether (MTBE) due to the low biomass yield of MTBE which has been one of the factors for low-rate MTBE degradation. The influence of various organic substrates on the rate of aerobic degradation of methyl tert-butyl ether (MTBE) by Methylibium petroleiphilum PM1 was investigated, and only yeast extract (YE), beef extract and tryptone exhibited stimulatory effect. With the concentration of each substrate being 100 mg/L, the average MTBE removal rate could increase to 1.29, 1.20 and 1.04 mg/(L h), respectively, in comparison with 0.71 mg/(L h) when carried out in medium without addition. The stimulatory effects of YE addition, as well as induction period required by MTBE degradation, varied dramatically with the storage conditions, pre-culture medium and concentrations of the inoculums. The extent of stimulatory effects of YE might be closely related to the proportion of induction period in the total time of MTBE-degradation. The removal efficiency increased from about 50% to 90.5% with the addition of YE in a packed-bed reactor loaded with calcium alginate immobilized cells.

Reversal of rocuronium-induced (1.2 mg kg-1) profound neuromuscular block by accidental high dose of sugammadex (40 mg kg-1).

NARCIS (Netherlands)

Molina, A.L.; Boer, H.D. de; Klimek, M.; Heeringa, M.; Klein, J.

2007-01-01

Sugammadex is the first selective relaxant binding agent and reverses rocuronium-induced neuromuscular block. A case is reported in which a patient accidentally received a high dose of sugammadex (40 mg kg-1) to reverse a rocuronium-induced (1.2 mg kg-1) profound neuromuscular block. A fast and

Replacing Phosphorus-Containing Food Additives With Foods Without Additives Reduces Phosphatemia in End-Stage Renal Disease Patients: A Randomized Clinical Trial.

Science.gov (United States)

de Fornasari, Margareth Lage Leite; Dos Santos Sens, Yvoty Alves

2017-03-01

The purpose of the study was to verify the effects of replacing phosphorus-containing food additives with foods without additives on phosphatemia in end-stage renal disease (ESRD) patients. Randomized clinical trial. Adult patients on hemodialysis for ≥6 months at a single center. A total of 134 patients with phosphorus levels of >5.5 mg/dL were included and were randomized into an intervention group (n = 67) and a control group (n = 67). The IG received individual orientation to replace processed foods that have phosphorus additives with foods of similar nutritional value without these additives. The CG received only the nutritional orientation given before the study. Clinical laboratory data, nutritional status, energy and protein intake, and normalized protein nitrogen appearance (nPNA) were evaluated at the beginning of the study and after 90 days. There was no initial difference between the groups in terms of serum phosphorus levels, nutritional status, and energy intake. After 3 months, there was a decline in phosphorus levels in the IG (from 7.2 ± 1.4 to 5.0 ± 1.3 mg/dL, P food additives with foods without additives reduced serum phosphorus without interfering in the nutritional status of ESRD patients. Copyright © 2016 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Cuscuta chinensis extract promotes osteoblast differentiation and mineralization in human osteoblast-like MG-63 cells.

Science.gov (United States)

Yang, Hyun Mo; Shin, Hyun-Kyung; Kang, Young-Hee; Kim, Jin-Kyung

2009-02-01

The aim of the present study was to investigate whether the aqueous extract of To-Sa-Za (TSZ-AE), the seed of Cuscuta chinensis Lam., which is a traditional medicinal herb commonly used in Korea and other oriental countries, could induce osteogenic activity in human osteoblast-like MG-63 cells. TSZ-AE treatment mildly promoted the proliferation of MG-63 cells at doses of 500 and 1,000 microg/mL in the 24-hour culture period. Dose-dependent increases in alkaline phosphatase (ALP) activity and collagen synthesis were shown at 48 and 72 hours of incubation. The release of bone morphogenetic protein (BMP)-2 but not osteocalcin in the MG-63 cells was induced by TSZ-AE at 72 hours (100-1,000 microg/mL). In addition, TSZ-AE markedly increased mRNA expression of ALP, collagen, and BMP-2 in the MG-63 cells in a dose-dependent manner. Mineralization in the culture of MG-63 cells was significantly induced at 500 and 1,000 microg/mL TSZ-AE treatment. In conclusion, this study shows that TSZ-AE enhanced ALP activity, collagen synthesis, BMP-2 expression, and mineralization in MG-63 cells. These results strongly suggest that C. chinensis can play an important role in osteoblastic bone formation and may possibly lead to the development of bone-forming drugs.

The effect of copper additions in the synthesis of in situ MgB2 Cu-sheathed wires

International Nuclear Information System (INIS)

Woźniak, M.; Hopkins, S.C.; Gajda, D.; Glowacki, B.A.

2012-01-01

The powder-in-tube (PIT) technique has been used to fabricate copper-sheathed magnesium diboride (MgB 2 ) wires using an insitu reaction method. The effect of copper powder additions, magnesium-boron molar ratio and heat treatment is studied by SEM, XRD, transport critical current I c (B) and resistivity ρ(T, B) measurements. The results show that addition of copper powder to the core of the wire accelerates the formation of MgB 2 and hence increases its amount and greatly decreases the amount of Mg-Cu intermetallic phases present in the core of the wire after heat treatment. Excess magnesium proved to be effective in compensating for Mg loss due to interdiffusion with the Cu of the wire sheath and resulted in less unreacted boron in the core for wires without added Cu, but seems to oppose the accelerated formation of MgB 2 in Cu added wires. The highest critical current density, 2.8 × 10 4 A cm -2 at 3 T and 4.2 K, was achieved for a wire with a stoichiometric Mg:B ratio and 3 at.% added copper powder heat treated at 700 °C for 5 min.

Comparison of Antioxidant Properties of Wild Blueberries (Vaccinium arctostaphylos L. and Vaccinium myrtillus L. with Cultivated Blueberry Varieties (Vaccinium corymbosum L. in Artvin Region of Turkey

Directory of Open Access Journals (Sweden)

Özlem Saral

2014-09-01

Full Text Available Vaccinium arctostaphylos L. and Vaccinium myrtillus L. which are found naturally in most part of Blacksea Region, and Artvin are generally called bear grape, Trabzon tea, and likapa. In addition, different varieties of blueberry (Vaccinium corymbosum L. have been cultivated in Artvin region for 5 or 6 years. Blueberries contain appreciable levels of phenolic compounds, including anthocyanins and flavonols that have high biological activity. V. arctostaphylos and V. myrtillus show that natural distrubition with received V. corymbosum of different cultured species in Artvin region will be determined antioxidant activity in this study. In this study showed that wild species had a higher antioxidant effect than cultivated species. V. myrtillus had high total polyphenols (11.539-20.742 mg GAE/g dry sample, flavonoids (1.182-2.676 mg QE/g dry sample and anthocyanins (3.305-11.473 mg Cyn/g dry sample than V. corymbosum species. In addition, wild species had high CUPRAC, FRAP and DPPH values. The antioxidant activities found with CUPRAC, expressed as trolox equivalent antioxidant capacity ranged from 0.143 to 0.297 mmol TEAC/g dry sample. Those determined with DPPH expressed as IC50 ranged from 0.229 to 1.178 mg/ml. Those determined with FRAP expressed as FeSO4.7H2O equivalent were in 130.719–346.115 µmol Fe/g dry sample range.

Effect of Cr, Ti, V, and Zr Micro-additions on Microstructure and Mechanical Properties of the Al-Si-Cu-Mg Cast Alloy

Science.gov (United States)

Shaha, S. K.; Czerwinski, F.; Kasprzak, W.; Friedman, J.; Chen, D. L.

2016-05-01

Uniaxial static and cyclic tests were used to assess the role of Cr, Ti, V, and Zr additions on properties of the Al-7Si-1Cu-0.5Mg (wt pct) alloy in as-cast and T6 heat-treated conditions. The microstructure of the as-cast alloy consisted of α-Al, eutectic Si, and Cu-, Mg-, and Fe-rich phases Al2.1Cu, Al8.5Si2.4Cu, Al5.2CuMg4Si5.1, and Al14Si7.1FeMg3.3. In addition, the micro-sized Cr/Zr/Ti/V-rich phases Al10.7SiTi3.6, Al6.7Si1.2TiZr1.8, Al21.4Si3.4Ti4.7VZr1.8, Al18.5Si7.3Cr2.6V, Al7.9Si8.5Cr6.8V4.1Ti, Al6.3Si23.2FeCr9.2V1.6Ti1.3, Al92.2Si16.7Fe7.6Cr8.3V1.8, and Al8.2Si30.1Fe1.6Cr18.8V3.3Ti2.9Zr were present. During solution treatment, Cu-rich phases were completely dissolved, while the eutectic silicon, Fe-, and Cr/Zr/Ti/V-rich intermetallics experienced only partial dissolution. Micro-additions of Cr, Zr, Ti, and V positively affected the alloy strength. The modified alloy in the T6 temper during uniaxial tensile tests exhibited yield strength of 289 MPa and ultimate tensile strength of 342 MPa, being significantly higher than that for the Al-Si-Cu-Mg base. Besides, the cyclic yield stress of the modified alloy in the T6 state increased by 23 pct over that of the base alloy. The fatigue life of the modified alloy was substantially longer than that of the base alloy tested using the same parameters. The role of Cr, Ti, V, and Zr containing phases in controlling the alloy fracture during static and cyclic loading is discussed.

Multilevel processor-sharing algorithm for M/G/1 systems with priorities

Energy Technology Data Exchange (ETDEWEB)

Yassouridis, A.; Koller, R.

1983-01-01

The well-known multilevel processor-sharing algorithm for M/G/1 systems without priorities is extended to M/G/1 systems with priority classes. The average response time t/sub j/(x) and the average waiting time w/sub j/(x) for a j-class job, which requires a total service of x sec, are analytically calculated. Some figures demonstrate how the priority classes and the total number of different levels affect the behaviour of the functions t/sub j/(x) and w/sub j/(x). In addition, the foreground-background algorithm with priorities, which is not yet covered in the literature, is treated as a special case of the multilevel processor-sharing algorithm. 8 references.

Synthesis of Mg2FeH6 containing as additives transition metal and transition metal fluorides or carbon

International Nuclear Information System (INIS)

Zepon, G.; Leiva, D.R.; Botta, W.J.

2010-01-01

The Mg 2 FeH 6 is a promising way of storing hydrogen in solid form, composed by elements that have low cost and, at the same time, high volumetric storage density: 150 kg H 2 /m 3 . However, this complex hydride is not easily synthesized as a single phase material. The hydrogen sorption high temperature and slow kinetics are the major limitations for the practical application of the Mg 2 FeH 6 as a hydrogen storage material. Little is known about the effects of additives in Mg 2 FeH 6 based nanocomposites in this work were synthesized by MAE under hydrogen atmosphere nanocomposites based on Mg 2 FeH 6 containing additives as transition metals, transition metals fluorides of transition metals or carbon, in order to obtain information on the effects of the selected additives. To this end, we used characterization techniques such as XRD, SEM and TEM, thermal analysis by DSC and curves made in apparatus PCT.(author)

Influence of small additions of Sc and Zr on structure and mechanical properties of Al-Zn-Mg-Cu alloy

International Nuclear Information System (INIS)

Kajgorodova, L.I.; Sel'nikhina, E.I.; Tkachenko, E.A.; Senatorova, O.G.

1996-01-01

A study was made into Sc and Zr addition effects on grain structure formation, supersaturated solid solution decomposition and mechanical properties of Al-7%Zn-2%Mg-1.2%Cu alloy. It is shown that grain structure is determined by volume fraction and distribution character of disperse particles of Al 3 Sc and Al 3 (Sc 1-x Zr x ). The reason for additives influence on decomposition kinetics during natural and artificial ageing are revealed. The structural factors responsible for the enhancement of mechanical properties on alloying are discussed. 17 refs.; 5 figs.; 2 tabs

The Influence of Cu Addition on Dispersoid Formation and Mechanical Properties of Al-Mn-Mg 3004 Alloy

Directory of Open Access Journals (Sweden)

Zhen Li

2018-03-01

Full Text Available The effect of Cu addition on dispersoid precipitation, mechanical properties and creep resistance was investigated in an Al-Mn-Mg 3004 alloy. The addition of Cu promoted dispersoid precipitation by increasing the number density and decreasing the size of dispersoids. Metastable β′-Mg2Si and Q-AlCuMgSi precipitates were observed during the heating process and both could provide favorable nucleation sites for dispersoid precipitation. The addition of Cu improved the thermal stability of dispersoids during a long-term thermal holding at 350 °C for 500 h. Results of mechanical testing show that the addition of Cu remarkably improved the hardness at room temperature, as well as the yield strength and creep resistance at 300 °C, which was mainly attributed to dispersoid strengthening and Cu solid solution strengthening. The yield strength contribution at 300 °C was quantitatively evaluated based on the dispersoid, solid solution and matrix contributions. It was confirmed that dispersoid strengthening is the main strengthening mechanism in the experimental alloys.

Hardening mechanisms of spray formed Al-Zn-Mg-Cu alloys with scandium and other elemental additions

International Nuclear Information System (INIS)

Sharma, M.M.; Amateau, M.F.; Eden, T.J.

2006-01-01

The hardening mechanisms in spray formed Al-Zn-Mg-Cu alloys with additions of chromium, zinc and scandium were studied. The microstructure of the spray formed alloys was analyzed by transmission electron microscopy. A range of tensile strengths were achieved, and varied based on elemental additions, and second phase particle strengthening. To explain the significantly higher strength in one alloy with scandium, theoretical results due to the yield stress of Al-Zn-Mg-Cu alloys as a function of volume fraction and precipitate particle size, were compared to experimental data. Both the possibilities of coherency and order strengthening are examined. The significant additional hardening achieved in the alloy with scandium is attributed to small ordered particles of Al 3 Sc, which precipitated during aging

Carbon nanosheets-based supercapacitors: Design of dual redox additives of 1, 4-dihydroxyanthraquinone and hydroquinone for improved performance

Science.gov (United States)

Xu, Dong; Sun, Xiao Na; Hu, Wei; Chen, Xiang Ying

2017-07-01

Using thiocarbanilide and Mg(OH)2 powders as carbon precursor and template, respectively, novel 2D carbon nanosheets with large area have been produced. Next, based on the cooperative effect, 1, 4-dihydroxyanthraquinone (DQ) and hydroquinone (HQ) regarded as efficient dual redox additives have been incorporated into the electrode carbon material and H2SO4 electrolyte, respectively, to largely elevate the capacitive performance of supercapacitors. More importantly, the cooperative effect results from the redox processes of DQ and HQ consecutively occurring in the electrode carbon material and aqueous H2SO4 electrolyte, respectively. Besides, the molar ratio of DQ and HQ exerts a crucial role in the determination of the electrochemical behaviors and eventually the optimum condition is the mass ratio of 1:1 concerning the DQ and porous carbon within solid electrode while retaining the HQ concentration as 20 mmol L-1 in 1 mol L-1 H2SO4 electrolyte. As a result, the maximum specific capacitance is achieved of 239 F g-1 at 3 A g-1, and furthermore the maximum energy density up to 21.1 Wh kg-1 is almost 3.5 times larger than that of the one without introducing any redox additive.

Directed modification of L-LcLDH1, an L-lactate dehydrogenase from Lactobacillus casei, to improve its specific activity and catalytic efficiency towards phenylpyruvic acid.

Science.gov (United States)

Li, Jian-Fang; Li, Xue-Qing; Liu, Yan; Yuan, Feng-Jiao; Zhang, Ting; Wu, Min-Chen; Zhang, Ji-Ru

2018-05-22

To improve the specific activity and catalytic efficiency of L-LcLDH1, an NADH-dependent allosteric L-lactate dehydrogenase from L. casei, towards phenylpyruvic acid (PPA), its directed modification was conducted based on the semi-rational design. The three variant genes, Lcldh1 Q88R , Lcldh1 I229A and Lcldh1 T235G , were constructed by whole-plasmid PCR as designed theoretically, and expressed in E. coli BL21(DE3), respectively. The purified mutant, L-LcLDH1 Q88R or L-LcLDH1 I229A , displayed the specific activity of 451.5 or 512.4 U/mg towards PPA, by which the asymmetric reduction of PPA afforded L-phenyllactic acid (PLA) with an enantiomeric excess (ee p ) more than 99%. Their catalytic efficiencies (k cat /K m ) without D-fructose-1,6-diphosphate (D-FDP) were 4.8- and 5.2-fold that of L-LcLDH1. Additionally, the k cat /K m values of L-LcLDH1 Q88R and L-LcLDH1 I229A with D-FDP were 168.4- and 8.5-fold higher than those of the same enzymes without D-FDP, respectively. The analysis of catalytic mechanisms by molecular docking (MD) simulation indicated that substituting I229 in L-LcLDH1 with Ala enlarges the space of substrate-binding pocket, and that the replacement of Q88 with Arg makes the inlet of pocket larger than that of L-LcLDH1. Copyright © 2018 Elsevier B.V. All rights reserved.

Concentrations of moxifloxacin in serum and pulmonary compartments following a single 400 mg oral dose in patients undergoing fibre-optic bronchoscopy.

Science.gov (United States)

Soman, A; Honeybourne, D; Andrews, J; Jevons, G; Wise, R

1999-12-01

The concentrations of moxifloxacin achieved after a single 400 mg dose were measured in serum, epithelial lining fluid (ELF), alveolar macrophages (AM) and bronchial mucosa (BM). Concentrations were determined using a microbiological assay. Nineteen patients undergoing fibre-optic bronchoscopy were studied. Mean serum, ELF, AM and BM concentrations at 2.2, 12 and 24 h were as follows: 2.2 h: 3.2 mg/L, 20.7 mg/L, 56.7 mg/L, 5.4 mg/kg; 12 h: 1.1 mg/L, 5.9 mg/L, 54.1 mg/L, 2.0 mg/kg; 24 h: 0.5 mg/L, 3.6 mg/L, 35.9 mg/L, 1.1 mg/kg, respectively. These concentrations exceed the MIC(90)s for common respiratory pathogens such as Streptococcus pneumoniae (0.25 mg/L), Haemophilus influenzae (0.03 mg/L), Moraxella catarrhalis (0.12 mg/L), Chlamydia pneumoniae (0.12 mg/L) and Mycoplasma pneumoniae (0. 12 mg/L) and indicate that moxifloxacin should be effective in the treatment of community-acquired, lower respiratory tract infections.

Dry sliding wear behaviour of Al-12Si-4Mg alloy with cerium addition

International Nuclear Information System (INIS)

Anasyida, A.S.; Daud, A.R.; Ghazali, M.J.

2010-01-01

The purpose of this work is to understand the effect of cerium addition on wear resistance behaviour of as-cast alloys. Al-12Si-4 Mg alloys with 1-5 wt% cerium addition were prepared using the casting technique. A sliding wear test was carried out under applied loads of 10 N, 30 N and 50 N at a fixed sliding speed of 1 m/s using a pin-on-disc configuration. The wear test was conducted in dry conditions at room temperature of ∼25 o C. Detailed analysis of the microstructure, worn surface, collected debris and microhardness was undertaken in order to investigate the differences between the as-cast alloys with different levels of cerium addition. The addition of 1-5 wt% cerium was found to lead to the precipitation of intermetallic phases (Al-Ce), resulting a needle-like structures. Increasing cerium content up to 2 wt% improved both wear resistance and microhardness of as-cast alloys. Addition of more than 2 wt% cerium, however, led to a decrease in microhardness, resulting in lower wear resistance of the alloys. Moderate wear was observed at all loads, with specific wear rates (K') ranging from 6.82 x 10 -5 with 2 wt% Ce at applied load of 50 N to 21.48 x 10 -5 mm 3 /N m without added Ce at an applied load of 10 N. Based on K' ranges, the as-cast alloys exhibited moderate wear regimes, and the mechanism of wear is a combination of abrasion and adhesion. Alloy containing 2 wt% Ce, with the highest hardness and lowest K' value, showed the greatest wear resistance.

Alternaria sp. MG1, a resveratrol-producing fungus: isolation, identification, and optimal cultivation conditions for resveratrol production.

Science.gov (United States)

Shi, Junling; Zeng, Qin; Liu, Yanlin; Pan, Zhongli

2012-07-01

Due to its potential in preventing or slowing the occurrence of many diseases, resveratrol (3,5,4'-trihydroxystilbene) has attracted great research interest. The objective of this study was to identify microorganisms from selected plants that produce resveratrol and to optimize the conditions for resveratrol production. Endophytes from Merlot wine grapes (Vitis vinifera L. cv. Merlot), wild Vitis (Vitis quinquangularis Rehd.), and Japanese knotweed (Polygonum cuspidatum Siebold & Zucc.) were isolated, and their abilities to produce resveratrol were evaluated. A total of 65 isolates were obtained and 21 produced resveratrol (6-123 μg/L) in liquid culture. The resveratrol-producing isolates belonged to seven genera, Botryosphaeria, Penicillium, Cephalosporium, Aspergillus, Geotrichum, Mucor, and Alternaria. The resveratrol-producing capability decreased or was completely lost in most isolates after three rounds of subculture. It was found that only the strain Alternaria sp. MG1 (isolated from cob of Merlot using GA1 medium) had stable and high resveratrol-producing capability in all subcultures. During liquid cultivation of Alternaria sp. MG1 in potato dextrose medium, the synthesis of resveratrol began on the first day, increased to peak levels on day 7, and then decreased sharply thereafter. Cell growth increased during cultivation and reached a stable and high level of biomass after 5 days. The best fermentation conditions for resveratrol production in liquid cultures of Alternaria sp. MG1 were an inoculum size of 6 %, a medium volume of 125 mL in a 250-mL flask, a rotation speed of 101 rpm, and a temperature of 27 °C.

Preparation of a Ni-MgO-Al2O3 catalyst with high activity and resistance to potassium poisoning during direct internal reforming of methane in molten carbonate fuel cells

Science.gov (United States)

Jang, Won-Jun; Jung, You-Shick; Shim, Jae-Oh; Roh, Hyun-Seog; Yoon, Wang Lai

2018-02-01

Steam reforming of methane (SRM) is conducted using a series of Ni-MgO-Al2O3 catalysts for direct internal reforming (DIR) in molten carbonate fuel cells (MCFCs). Ni-MgO-Al2O3 catalysts are prepared by the homogeneous precipitation method with a variety of MgO loading amounts ranging from 3 to 15 wt%. In addition, each precursor concentrations are systemically changed (Ni: 1.2-4.8 mol L-1; Mg: 0.3-1.2 mol L-1; Al: 0.4-1.6 mol L-1) at the optimized composition (10 wt% MgO). The effects of MgO loading and precursor concentration on the catalytic performance and resistance against poisoning of the catalyst by potassium (K) are investigated. The Ni-MgO-Al2O3 catalyst with 10 wt% MgO and the original precursor concentration (Ni: 1.2 mol L-1; Mg: 0.3 mol L-1; Al: 0.4 mol L-1) exhibits the highest CH4 conversion and resistance against K poisoning even at the extremely high gas space velocity (GHSV) of 1,512,000 h-1. Excellent SRM performance of the Ni-MgO-Al2O3 catalyst is attributed to strong metal (Ni) to alumina support interaction (SMSI) when magnesium oxide (MgO) is co-precipitated with the Ni-Al2O3. The enhanced interaction of the Ni with MgO-Al2O3 support is found to protect the active Ni species against K poisoning.

Perbandingan Gabapentin 600 mg dengan 1.200 mg per Oral Preoperatif terhadap Nilai Visual Analogue Scale dan Pengurangan Kebutuhan Petidin Pascaoperasi pada Modifikasi Mastektomi Radikal

Directory of Open Access Journals (Sweden)

Ardi Zulfariansyah

2013-12-01

Full Text Available Gabapentin is a GABA analog which has the effect of anti hyperalgesia, anti allodynia, and anti nociceptive. This research was conducted in order to assess the effect of 600mg and 1,200 mg gabapentin given preoperatively to assess visual analogue scale (VAS score and reduction of pethidine requirement. The study was done by conducting a double blind randomized controlled trial on 38 patients, aged 18–65 years, with ASA physical status I–II. Patients were divided into two groups: 600 mg gabapentin and 1,200 mg gabapentin group. The quality of pain was assessed using VAS score. The results were statistically analyzed using Mann-Whitney Test with 95% confidence interval and considered significant if p value <0.05. From the results, the VAS values obtained at rest and during mobilization were significantly different (p<0.05. The 1,200 mg gabapentin group received less additional pethidine (10.5% vs 15.8%, although no significant difference was shown (p=0.631. The conclusion of this study is that administration of 1,200 mg gabapentin per oral pre operatively is better when compared to 600 mg in reducing post operative visual analog scale score in modified radical mastectomy. However, it do not reduce the need for analgesic significantly.

The Growth and Cultivation of Meristem From Shallot (Allium ascalonicum L. cv. Katumi by In Vitro

Directory of Open Access Journals (Sweden)

Lamro Purba

2017-12-01

Full Text Available This study aimed for knowing and obtaining the best concentration of kinetin and NAA interaction effects in influencing the shoot induction, knowing how the plant growth regulators in induction mediastill affect the shoot additionin the MS0media and also knowing the largest number of roots in rooting media for shallot by in vitro. The experiment was conducted at Laboratory of Tissue Culture Seed Technology, Faculty of Agriculture, Padjadjaran University, during January 2011 until May 2011. This experiment divided in 3 stages, namely shoot induction stage, shoot subculture to MS0 media stage and shoot subculture to rooting media stage. Experimental method used in the shoot induction stage was factorial Completely Randomized Design with three replications. The first factor was the kinetin with four levels,0, 1, 2, and 3 mg L-1. The second factor was the NAA with three levels, as 0, 0.01, and 0.1 mg L-1. Basic media used for each treatment was MS. The experiment result showed there was an interaction between kinetin and NAA on shoot induction stagewith the plantlet height, leaf number, and shoot addition. The best result for leaf number was gained from interaction with 2 mg L-1 kinetin without NAA,while the treatment of 2 mg L-1 kinetin with 0.01 mg L-1 NAA gave a better interaction for theshoot addition variable.

Examination of correlation between histidine and nickel absorption by Morus L., Robinia pseudoacacia L. and Populus nigra L. using HPLC-MS and ICP-MS.

Science.gov (United States)

Ozen, Sukran Akkus; Yaman, Mehmet

2016-08-02

In this study, HPLC-MS and ICP-MS methods were used for the determination of histidine and nickel in Morus L., Robinia pseudoacacia L., and Populus nigra L. leaves taken from industrial areas including Gaziantep and Bursa cities. In the determination of histidine by HPLC-MS, all of the system parameters such as flow rate of mobile phase, fragmentor potential, injection volume and column temperature were optimized and found to be 0.2 mL min(-1), 70 V, 15 µL, and 20°C, respectively. Under the optimum conditions, histidine was extracted from plant sample by distilled water at 90°C for 30 min. Concentrations of histidine as mg kg(-1) were found to be between 2-9 for Morus L., 6-13 for Robinia pseudoacacia L., and 2-10 for Populus nigra L. Concentrations of nickel were in the ranges of 5-10 mg kg(-1) for Morus L., 3-10 mg kg(-1) for Robinia pseudoacacia L., and 0.6-4 mg kg(-1) for Populus nigra L. A significant linear correlation (r = 0.78) between histidine and Ni was observed for Populus nigra L., whereas insignificant linear correlation for Robinia pseudoacacia L. (r = 0.22) were seen. Limits of detection (LOD) and quantitation (LOQ) were found to be 0.025 mg Ni L(-1) and 0.075 mg Ni L(-1), respectively.

Effect of sulfate absence and nitrate addition on bacterial community in a sulfidogenic bioreactor

Energy Technology Data Exchange (ETDEWEB)

Zhao Yangguo [College of Environmental Science and Engineering, Ocean University of China, Qingdao 266100 (China); State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China); Wang Aijie, E-mail: waj0578@hit.edu.cn [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China); Ren Nanqi [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China)

2009-12-30

The characteristics and behavior of sulfate-reducing bacteria (SRB), methane-producing bacteria (MPB) and denitrifying bacteria (DB) were investigated by polymerase chain reaction (PCR) based methods under the transitory sulfate absence or nitrate addition conditions in a sulfidogenic continuously stirred tank reactor. The bioreactor started-up feeding with 4000 mg l{sup -1} COD (lactate) and 2000 mg l{sup -1} sulfate (SO{sub 4}{sup 2-}). The sulfate removal efficiency reached 3.84 g l{sup -1} d{sup -1} when the activated sludge formed a stable bacterial community comprising of some members of genera Desulfobulbus, Desulfovibrio, Clostridium and Pseudomonas after 20 days' operation. And about 79% of reduced sulfate captured electrons from the oxidization of propionate. Sulfate absence influenced little on quantity and population structure of SRB and DB, while much on MPB and metabolic typing. And the acetate (up to 86% (w/w) of total end-products) in end-product profiles was replaced by the propionate (75% (w/w)). The addition of nitrate to sulfidogenic system suppressed the sulfidogenesis mainly by capturing the electron flow. These results suggested that sulfate absence or nitrate addition would not inhibit SRB permanently in a stable sulfidogenic community.

Unique antitumor property of the Mg-Ca-Sr alloys with addition of Zn

Science.gov (United States)

Wu, Yuanhao; He, Guanping; Zhang, Yu; Liu, Yang; Li, Mei; Wang, Xiaolan; Li, Nan; Li, Kang; Zheng, Guan; Zheng, Yufeng; Yin, Qingshui

2016-02-01

In clinical practice, tumor recurrence and metastasis after orthopedic prosthesis implantation is an intensely troublesome matter. Therefore, to develop implant materials with antitumor property is extremely necessary and meaningful. Magnesium (Mg) alloys possess superb biocompatibility, mechanical property and biodegradability in orthopedic applications. However, whether they possess antitumor property had seldom been reported. In recent years, it showed that zinc (Zn) not only promote the osteogenic activity but also exhibit good antitumor property. In our present study, Zn was selected as an alloying element for the Mg-1Ca-0.5Sr alloy to develop a multifunctional material with antitumor property. We investigated the influence of the Mg-1Ca-0.5Sr-xZn (x = 0, 2, 4, 6 wt%) alloys extracts on the proliferation rate, cell apoptosis, migration and invasion of the U2OS cell line. Our results show that Zn containing Mg alloys extracts inhibit the cell proliferation by alteration the cell cycle and inducing cell apoptosis via the activation of the mitochondria pathway. The cell migration and invasion property were also suppressed by the activation of MAPK (mitogen-activated protein kinase) pathway. Our work suggests that the Mg-1Ca-0.5Sr-6Zn alloy is expected to be a promising orthopedic implant in osteosarcoma limb-salvage surgery for avoiding tumor recurrence and metastasis.

Low-density lipoprotein cholesterol of less than 70 mg/dL is associated with fewer cardiovascular events in acute coronary syndrome patients: a real-life cohort in Thailand

Directory of Open Access Journals (Sweden)

Chinwong D

2015-04-01

Full Text Available Dujrudee Chinwong,1,2 Jayanton Patumanond,3 Surarong Chinwong,1 Khanchai Siriwattana,4 Siriluck Gunaparn,5 John Joseph Hall,6 Arintaya Phrommintikul5 1Department of Pharmaceutical Care, Faculty of Pharmacy, Chiang Mai University, Chiang Mai, Thailand; 2Clinical Epidemiology Program, Faculty of Medicine, Chiang Mai University, Chiang Mai, Thailand; 3Center of Excellence in Applied Epidemiology, Faculty of Medicine, Thammasat University, Pathum Thani, Thailand; 4Division of Medicine, Nakornping Hospital, Chiang Mai, Thailand; 5Department of Internal Medicine, Faculty of Medicine, Chiang Mai University, Chiang Mai, Thailand; 6Centre for Clinical Epidemiology and Biostatistics, School of Medicine and Public Health, Faculty of Health, University of Newcastle, Callaghan, NSW, Australia Background: Elevated low-density lipoprotein cholesterol (LDL-C is associated with an increased risk of cardiovascular disease or mortality; however, the LDL-C goal for therapy in acute coronary syndrome (ACS patients is controversial and varies among guidelines. This study aimed to assess the effect of reaching an LDL-C goal of <70 mg/dL (<1.8 mmol/L on first composite cardiovascular outcomes in routine clinical practice in Thailand.Methods: A retrospective cohort study was conducted using medical charts and the electronic hospital database of patients diagnosed with ACS and treated with statins at a tertiary care hospital in Thailand between 2009 and 2012. After admission, patients were followed from the date of LDL-C goal assessment until the first event of composite cardiovascular outcomes (nonfatal ACS, nonfatal stroke, or all-cause death. Cox proportional hazard models adjusted for potential confounders were used.Results: Of 405 patients, mean age was 65 years (60% males. Twenty-seven percent of the patients attained an LDL-C goal of <70 mg/dL, 38% had LDL-C between 70 and 99 mg/dL, and 35% had LDL-C ≥100 mg/dL. Forty-six patients experienced a composite

Microbial Detoxification of Deoxynivalenol (DON), Assessed via a Lemna minor L. Bioassay, through Biotransformation to 3-epi-DON and 3-epi-DOM-1.

Science.gov (United States)

Vanhoutte, Ilse; De Mets, Laura; De Boevre, Marthe; Uka, Valdet; Di Mavungu, José Diana; De Saeger, Sarah; De Gelder, Leen; Audenaert, Kris

2017-02-13

Mycotoxins are toxic metabolites produced by fungi. To mitigate mycotoxins in food or feed, biotransformation is an emerging technology in which microorganisms degrade toxins into non-toxic metabolites. To monitor deoxynivalenol (DON) biotransformation, analytical tools such as ELISA and liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) are typically used. However, these techniques do not give a decisive answer about the remaining toxicity of possible biotransformation products. Hence, a bioassay using Lemna minor L. was developed. A dose-response analysis revealed significant inhibition in the growth of L. minor exposed to DON concentrations of 0.25 mg/L and higher. Concentrations above 1 mg/L were lethal for the plant. This bioassay is far more sensitive than previously described systems. The bioassay was implemented to screen microbial enrichment cultures, originating from rumen fluid, soil, digestate and activated sludge, on their biotransformation and detoxification capability of DON. The enrichment cultures originating from soil and activated sludge were capable of detoxifying and degrading 5 and 50 mg/L DON. In addition, the metabolites 3-epi-DON and the epimer of de-epoxy-DON (3-epi-DOM-1) were found as biotransformation products of both consortia. Our work provides a new valuable tool to screen microbial cultures for their detoxification capacity.

Microbial Detoxification of Deoxynivalenol (DON, Assessed via a Lemna minor L. Bioassay, through Biotransformation to 3-epi-DON and 3-epi-DOM-1

Directory of Open Access Journals (Sweden)

Ilse Vanhoutte

2017-02-01

Full Text Available Mycotoxins are toxic metabolites produced by fungi. To mitigate mycotoxins in food or feed, biotransformation is an emerging technology in which microorganisms degrade toxins into non-toxic metabolites. To monitor deoxynivalenol (DON biotransformation, analytical tools such as ELISA and liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS are typically used. However, these techniques do not give a decisive answer about the remaining toxicity of possible biotransformation products. Hence, a bioassay using Lemna minor L. was developed. A dose–response analysis revealed significant inhibition in the growth of L. minor exposed to DON concentrations of 0.25 mg/L and higher. Concentrations above 1 mg/L were lethal for the plant. This bioassay is far more sensitive than previously described systems. The bioassay was implemented to screen microbial enrichment cultures, originating from rumen fluid, soil, digestate and activated sludge, on their biotransformation and detoxification capability of DON. The enrichment cultures originating from soil and activated sludge were capable of detoxifying and degrading 5 and 50 mg/L DON. In addition, the metabolites 3-epi-DON and the epimer of de-epoxy-DON (3-epi-DOM-1 were found as biotransformation products of both consortia. Our work provides a new valuable tool to screen microbial cultures for their detoxification capacity.

Microstructure and mechanical properties of an extruded Mg-8Bi-1Al-1Zn (wt%) alloy

Energy Technology Data Exchange (ETDEWEB)

Meng, Shuaiju [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Yu, Hui, E-mail: yuhuidavid@gmail.com [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Materials Commercialization Center, Korea Institute of Materials Science, Changwon 51508 (Korea, Republic of); Zhang, Huixing [Mechanical and Material School, Tianjin Sino-German University of Applied Sciences, Tianjin 300350 (China); Cui, Hongwei [School of Materials Science and Engineering, Shangdong University of Technology, Zibo 255049 (China); Park, Sung Hyuk [School of Materials Science and Engineering, Kyungpook National University, Daegu 702701 (Korea, Republic of); Zhao, Weiming [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); You, Bong Sun [Materials Commercialization Center, Korea Institute of Materials Science, Changwon 51508 (Korea, Republic of)

2017-04-06

In this study, the microstructural evolution and mechanical properties of a newly developed rare earth free Mg-8Bi-1Al-1Zn (BAZ811, in wt%) alloy were investigated and compared with those of a commercial AZ31 alloy. The as-extruded BAZ811 alloy with much finer grain size shows more homogeneous dynamical recrystallized (DRXed) microstructure and weaker basal texture than those of AZ31 alloy. In addition, compared with bimodal structure AZ31 alloy containing only relatively coarse and sparse Al{sub 8}Mn{sub 5} phases, the coexistence of strip-like fragmented Mg{sub 3}Bi{sub 2} precipitate and nano-size Mg{sub 3}Bi{sub 2} particles in the microstructure was observed in BAZ811 alloy. Moreover, the BAZ811 alloy exhibits a tensile yield stress of 291 MPa, an ultimate tensile strength of 331 MPa, an elongation to failure of 14.6% as well as a reduction in yield asymmetry, which is mainly attributed to the combined effects of grain refinement and micro-scale broken Mg{sub 3}Bi{sub 2} particles together with nano-scale spherical Mg{sub 3}Bi{sub 2} precipitates. The strain hardening behavior of both BAZ811 and AZ31 alloys were also discussed in terms of microstructure variation.

In-situ thermal analysis and macroscopical characterization of Mg-xCa and Mg-0.5Ca-xZn alloy systems

Energy Technology Data Exchange (ETDEWEB)

Farahany, Saeed [Department of Materials Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Bakhsheshi-Rad, Hamid Reza, E-mail: Rezabakhsheshi@gmail.com [Department of Materials Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Idris, Mohd Hasbullah [Department of Materials Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Abdul Kadir, Mohammed Rafiq [Medical Implants Technology Group, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Department of Biomechanics and Biomedical Materials, Faculty of Biomedical Engineering and Health Sciences, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Lotfabadi, Amir Fereidouni [Department of Manufacturing and Industrial Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Ourdjini, Ali [Department of Materials Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia)

2012-01-10

Highlights: Black-Right-Pointing-Pointer The effect of Ca and Zn addition on Mg-Ca and Mg-Ca-Zn were investigated. Black-Right-Pointing-Pointer Ca and Zn addition decreased solid fraction at coherency point. Black-Right-Pointing-Pointer T{sub N}-T{sub DCP} increased by adding Ca and Zn in Mg-Ca and Mg-Ca-Zn, respectively. Black-Right-Pointing-Pointer Three reactions were detected when Zn/Ca atomic ratio less than 1.25 in Mg-Ca-Zn. Black-Right-Pointing-Pointer A new peak Mg{sub 51}Zn{sub 20} was identified in Mg-0.5Ca-9Zn in addition of other peaks. - Abstract: This research described the identification phases by thermal analysis and microscopy inspection of Mg-xCa and Mg-0.5%Ca-xZn alloys that were solidified at slow cooling rate. Analysis of cooling curve after Ca addition shows the evolution of the Mg{sub 2}Ca intermetallic phase at around 520 Degree-Sign C in addition to {alpha}-Mg phase. First derivative curves of alloys after the addition of Zn to Mg-0.5Ca alloy reveals three peaks related to {alpha}-Mg, Mg{sub 2}Ca and Ca{sub 2}Mg{sub 6}Zn{sub 3} for alloys that have Zn/Ca atomic ratio less than 1.23. The peak of Mg{sub 2}Ca reaction on the first derivative curves disappeared for alloys containing Zn/Ca ratio more than 1.23. A new peak was also observed at 330 Degree-Sign C for Mg-0.5Ca-9Zn which was identified as Mg{sub 51}Zn{sub 20}. Solid fraction at coherency point decreased with increasing Ca and Zn elements. However, coherency time and difference between the nucleation and coherency temperatures (T{sub N}-T{sub DCP}) increased by adding Ca and Zn in Mg-Ca and Mg-Ca-Zn systems.

Elicitation of Jerusalem artichoke (Helianthus tuberosus L.) cell suspension culture for enhancement of inulin production and altered degree of polymerisation.

Science.gov (United States)

Ma, Chunquan; Zhou, Dong; Wang, Haitao; Han, Dongming; Wang, Yang; Yan, Xiufeng

2017-01-01

Plant cell suspension cultures have emerged as a potential source of secondary metabolites for food additives and pharmaceuticals. In this study inulin accumulation and its degree of polymerisation (DP) in the treated cells in the same medium were investigated after treatment with six types of elicitors. An in vitro cell suspension culture of Jerusalem artichoke (Helianthus tuberosus L.) was optimised by adding an extra nitrogen source. According to the growth kinetics, a maximum biomass of 5.48 g L -1 was obtained from the optimal cell suspension medium consisted of Murashige and Skoog basic medium (MS) + 1.0 mg L -1 α-naphthalene acetic acid (NAA) + 1.0 mg L -1 6-benzylaminopurine (6-BA) + 0.5 mg L -1 proline + 1.0 mg L -1 glutamine. Methyl jasmonate (MeJA, 250 µmol L -1 ) treatment for 15 days led to the highest levels of inulin (2955.27 ± 9.81 mg L -1 compared to control of 1217.46 ± 0.26 mg L -1 ). The elicited effect of five elicitors to the suspension cells of Jerusalem artichoke is as follows: AgNO 3 (Ag, 10 µmol L -1 ), salicylic acid (SA, 75 µmol L -1 ), chitosan (KJT, 40 mg L -1 ), Trichoderma viride (Tv, 90 mg L -1 ), yeast extract (YE, 0.25 mg L -1 ), and the corresponding content of inulin is increased by 2.05-, 1.93-, 1.76-, 1.44- and 1.18-fold compared to control, respectively. The obvious effect on the percentage of lower DP in inulin was observed in cells treated with 40 mg L -1 KJT, 0.25 mg L -1 YE and 10 µmol L -1 Ag. Among the six types of elicitors, the descending order of inulin content is MeJA > Ag > SA > KJT > Tv > YE. For the purpose inulin with lower DP and its application to prebiotic food, three elicitors, including KJT, YE and Ag, can be used for the elicitation. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Impact of Zn, Mg, Ni and Co elements on glass alteration: Additive effects

Energy Technology Data Exchange (ETDEWEB)

Aréna, H., E-mail: helene.arena@cea.fr [CEA, DEN, DTCD, LCLT, Centre de Marcoule, F-30207 Bagnols sur Cèze Cedex (France); Godon, N. [CEA, DEN, DTCD, LCLT, Centre de Marcoule, F-30207 Bagnols sur Cèze Cedex (France); Rébiscoul, D.; Podor, R. [ICSM-UMR5257 CNRS/CEA/UM2/ENCSM, Site de Marcoule, Bat. 426, 30207 Bagnols/Cèze (France); Garcès, E. [CEA, DEN, DTCD, LCLT, Centre de Marcoule, F-30207 Bagnols sur Cèze Cedex (France); Cabie, M. [Aix-Marseille Université, CP2M, F-13397 Marseille (France); Mestre, J.-P. [CEA, DEN, DTCD, LCLT, Centre de Marcoule, F-30207 Bagnols sur Cèze Cedex (France)

2016-03-15

The minor elements present in the nuclear glass composition or coming from the groundwater of the future repository may impact glass alteration. In this study, the effects of Zn, Mg, Ni and Co on the International Simple Glass (ISG) alteration were studied throughout 511 days of aqueous leaching experiments. The aim was to determine their additive or competitive effect on glass alteration and the nature of the alteration products. The four elements were introduced separately or altogether in solution as XCl{sub 2} chloride salts (X = Zn, Mg, Ni or Co) with monthly additions to compensate for their consumption. The alteration kinetics were determined by leachate analyses (ICP-AES) and alteration products were characterized in terms of composition, morphology and microstructure (SEM, TEM-EDX, ToF-SIMS and XRD). Results indicate that when they are introduced separately, Zn, Mg, Ni and Co have the same qualitative and quantitative effect on glass alteration kinetics and on pH: they form secondary phases leading to a pH decrease and a significant increase in glass alteration. The secondary phases were identified as silicates of the added X element: trioctahedral smectites with a stoichiometry of[(Si{sub (4-a)} Al{sub a}) (X{sub (3-b)} Al{sub b}) O{sub 10} (OH){sub 2}]{sup (a+b)−} [X{sub c} Na{sub d} Ca{sub e}] {sup (2c+d+2e) +} with a = 0.11 to 0.45, b = 0.00 to 0.29, c = 0, d = 0.19 to 0.74 and e = 0.10 to 0.14. . It was shown that as pH stabilizes at a minimum value, X-silicates no longer precipitate, thus leading to a significant drop in the glass alteration rate. This pH value depends on X and it has been identified as being 8 for Mg-silicates, probably around 7.3 for Ni and Co-silicates and less than 6.2 for Zn-silicates. When tested together, the effects of these four elements on glass alteration are additive and lead to the formation of a mix of X-silicates that precipitate as long as their constitutive elements are available and the pH is above

The effect of terebinth (Pistacia terebinthus L.) coffee addition on the chemical and physical characteristics, colour values, organic acid profiles, mineral compositions and sensory properties of ice creams.

Science.gov (United States)

Yüksel, Arzu Kavaz; Şat, Ihsan Güngör; Yüksel, Mehmet

2015-12-01

The aim of this research was to evaluate the effect of terebinth (Pistacia terebinthus L.) coffee addition (0.5, 1 and 2 %) on the chemical and physical properties, colour values, organic acid profiles, mineral contents and sensory characteristics of ice creams. The total solids, fat, titratable acidity, viscosity, first dripping time and complete melting time values, a (*) and b (*) colour properties, citric, lactic, acetic and butyric acid levels and Ca, Cu, Mg, Fe, K, Zn and Na concentrations of ice creams showed an increase with the increment of terebinth coffee amount, while protein, pH, L (*), propionic acid and orotic acid values decreased. However, Al and malic acid were not detected in any of the samples. The overall acceptability scores of the sensory properties showed that the addition of 1 % terebinth coffee to the ice cream was more appreciated by the panellists.

Class side effects: decreased pressure in the lower oesophageal and the pyloric sphincters after the administration of dopamine antagonists, neuroleptics, anti-emetics, L-NAME, pentadecapeptide BPC 157 and L-arginine.

Science.gov (United States)

Belosic Halle, Zeljka; Vlainic, Josipa; Drmic, Domagoj; Strinic, Dean; Luetic, Kresimir; Sucic, Mario; Medvidovic-Grubisic, Maria; Pavelic Turudic, Tatjana; Petrovic, Igor; Seiwerth, Sven; Sikiric, Predrag

2017-05-17

The ulcerogenic potential of dopamine antagonists and L-NAME in rats provides unresolved issues of anti-emetic neuroleptic application in both patients and experimental studies. Therefore, in a 1-week study, we examined the pressures within the lower oesophageal and the pyloric sphincters in rats [assessed manometrically (cm H 2 O)] after dopamine neuroleptics/prokinetics, L-NAME, L-arginine and stable gastric pentadecapeptide BPC 157 were administered alone and/or in combination. Medication (/kg) was given once daily intraperitoneally throughout the 7 days, with the last dose at 24 h before pressure assessment. Given as individual agents to healthy rats, all dopamine antagonists (central [haloperidol (6.25 mg, 16 mg, 25 mg), fluphenazine (5 mg), levomepromazine (50 mg), chlorpromazine (10 mg), quetiapine (10 mg), olanzapine (5 mg), clozapine (100 mg), sulpiride (160 mg), metoclopramide (25 mg)) and peripheral(domperidone (10 mg)], L-NAME (5 mg) and L-arginine (100 mg) decreased the pressure within both sphincters. As a common effect, this decreased pressure was rescued, dose-dependently, by BPC 157 (10 µg, 10 ng) (also note that L-arginine and L-NAME given together antagonized each other's responses). With haloperidol, L-NAME worsened both the lower oesophageal and the pyloric sphincter pressure, while L-arginine ameliorated lower oesophageal sphincter but not pyloric sphincter pressure, and antagonized L-NAME effect. With domperidone, L-arginine originally had no effect, while L-NAME worsened pyloric sphincter pressure. This effect was opposed by L-arginine. All these effects were further reversed towards a stronger beneficial effect, close to normal pressure values, by the addition of BPC 157. In addition, NO level was determined in plasma, sphincters and brain tissue. Thiobarbituric acid reactive substances (TBARS) were also assessed. Haloperidol increased NO levels (in both sphincters, the plasma and brain), consistently producing increased

Tem Observation Of Precipitate Structures In Al-Zn-Mg Alloys With Additions Of Cu/Ag

Directory of Open Access Journals (Sweden)

Watanabe K.

2015-06-01

Full Text Available Al-Zn-Mg alloy has been known as one of the aluminum alloys with the good age-hardening ability and the high strength among commercial aluminum alloys. The mechanical property of the limited ductility, however, is required to further improvement. In this work, three alloys, which were added Cu or Ag into the Al-Zn-Mg alloy, were prepared to compare the effect of the additional elements on the aging behavior. The content of Ag and Cu were 0.2at.% and the same as, respectively. Ag or Cu added alloy showed higher maximum hardness than base alloy. The particle shape and rod shape precipitates were observed in all alloys peak-aged at 423K. According to addition of Ag or Cu, the number density of the precipitates increased higher than that of base alloy.

Small Molecule Agonists of Cell Adhesion Molecule L1 Mimic L1 Functions In Vivo.

Science.gov (United States)

Kataria, Hardeep; Lutz, David; Chaudhary, Harshita; Schachner, Melitta; Loers, Gabriele

2016-09-01

Lack of permissive mechanisms and abundance of inhibitory molecules in the lesioned central nervous system of adult mammals contribute to the failure of functional recovery after injury, leading to severe disabilities in motor functions and pain. Peripheral nerve injury impairs motor, sensory, and autonomic functions, particularly in cases where nerve gaps are large and chronic nerve injury ensues. Previous studies have indicated that the neural cell adhesion molecule L1 constitutes a viable target to promote regeneration after acute injury. We screened libraries of known drugs for small molecule agonists of L1 and evaluated the effect of hit compounds in cell-based assays in vitro and in mice after femoral nerve and spinal cord injuries in vivo. We identified eight small molecule L1 agonists and showed in cell-based assays that they stimulate neuronal survival, neuronal migration, and neurite outgrowth and enhance Schwann cell proliferation and migration and myelination of neurons in an L1-dependent manner. In a femoral nerve injury mouse model, enhanced functional regeneration and remyelination after application of the L1 agonists were observed. In a spinal cord injury mouse model, L1 agonists improved recovery of motor functions, being paralleled by enhanced remyelination, neuronal survival, and monoaminergic innervation, reduced astrogliosis, and activation of microglia. Together, these findings suggest that application of small organic compounds that bind to L1 and stimulate the beneficial homophilic L1 functions may prove to be a valuable addition to treatments of nervous system injuries.

Orientation and magnetic properties of FePt and CoPt films grown on MgO(1 1 0) single-crystal substrate by electron-beam coevaporation

Energy Technology Data Exchange (ETDEWEB)

Yu Minghui [Department of Materials Science and Engineering, University of Maryland, College Park, MD 20742 (United States); Department of Physics, University of Texas at Arlington, Arlington, TX 76019 (United States); Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States)], E-mail: myu1@uno.edu; Ohguchi, H.; Zambano, A.; Takeuchi, I. [Department of Materials Science and Engineering, University of Maryland, College Park, MD 20742 (United States); Liu, J.P. [Department of Physics, University of Texas at Arlington, Arlington, TX 76019 (United States); Josell, D.; Bendersky, L.A. [Metallurgy Division, Materials Science and Engineering Laboratory, National Institute of Standards and Technology, Gaithersburg, MD 20899 (United States)

2007-09-25

We have studied the orientation and magnetic properties of FePt and CoPt films deposited by electron-beam co-evaporation on MgO(1 1 0) single-crystal substrates at substrate temperatures from 500 to 700 deg. C. We observed that long-range chemical ordering of the L1{sub 0} structure occurred over the entire range of substrate temperatures in FePt films and at 600 deg. C and up in CoPt films. Growth of FePt and CoPt yielded epitaxial films with cube-on-cube orientation of the pseudo-cubic L1{sub 0} lattice with respect to the cubic MgO. X-ray diffraction patterns and magnetization loops of the FePt and CoPt films revealed the existence of L1{sub 0} domains with the tetragonal c axis inclined at 45 deg. to the film plane, orientations (0 h h) and (h 0 h), as well as L1{sub 0} domains with the tetragonal c axis in the plane of the film, orientation (h h 0). The FePt and CoPt films for which X-ray diffraction indicated tetragonal phase was present all exhibited hard magnetic properties with easy axis along the [0 0 1] substrate direction as well as large in-plane magnetocrystalline anisotropy.

Vitamin, Trace Element, and Fatty Acid Levels of Vitex agnus-castus L., Juniperus oxycedrus L., and Papaver somniferum L. Plant Seeds

Directory of Open Access Journals (Sweden)

Ahmet Ozkaya

2013-01-01

Full Text Available The levels of fat-soluble vitamin, trace element and fatty acid of Vitex agnus-castus L., Juniperus oxycedrus L., and Papaver somniferum L. seeds in Turkey were determined by using HPLC, ICP-OES, and GC, respectively. In the Vitex agnus-castus L., Juniperus oxycedrus L., and Papaver somniferum L. seeds, linoleic acid (18 : 2 was determined with the highest level rates (%54.11, %28.03, and %72.14, resp.. In the Vitex agnus-castus L. seeds, R-tocopherol, α-tocopherol, and K1 levels were determined as 9.70 μg/g, 18.20 μg/g, and 24.79 μg/g, respectively; In the Juniperus oxycedrus L. seeds, R-tocopherol, α-tocopherol, and K1 were determined as 18.50 μg/g, 0.84 μg/g, and 5.00 μg/g, respectively, and in the Papaver somniferum L. seeds, R-tocopherol, α-tocopherol, K1, and D2 levels were determined as 43.25 μg/g, 122.05 μg/g, 12.01 μg/g, and 0.62 μg/g, respectively. In the Vitex agnus-castus L., Juniperus oxycedrus L., and Papaver somniferum L. seeds, nickel (Ni, zinc (Zn, and iron (Fe were determined with the trace element level rates (4.42 mg/kg, 10.43 mg/kg, 3.71 mg/kg for Ni, 7.00 mg/kg, 7.70 mg/kg, and 24 mg/kg for Zn and 93.73 mg/kg, 187.95 mg/kg, and 149.64 mg/kg for Fe, resp.. These parameters in seeds are very important for human life.

Effects of nickel(II) addition on the activity of activated sludge microorganisms and activated sludge process

International Nuclear Information System (INIS)

Ong, Soon-An; Toorisaka, Eiichi; Hirata, Makoto; Hano, Tadashi

2004-01-01

The effects of Ni(II) in a synthetic wastewater on the activity of activated sludge microorganisms and sequencing batch reactor (SBR) treatment process were investigated. Two parallel lab-scale SBR systems were operated. One was used as a control unit, while the other received Ni(II) concentrations equal to 5 and 10 mg/l. The SBR systems were operated with FILL, REACT, SETTLE, DRAW and IDLE modes in the time ratio of 0.5:3.5:1.0:0.75:0.25 for a cycle time of 6 h. The addition of Ni(II) into SBR system caused drastically dropped in TOC removal rate (k) and specific oxygen uptake rate (SOUR) by activated sludge microorganisms due to the inhibitory effects of Ni(II) on the bioactivity of microorganisms. The addition of 5 mg/l Ni(II) caused a slight reduction in TOC removal efficiency, whereas 10 mg/l Ni(II) addition significantly affected the SBR performance in terms of suspended solids and TOC removal efficiency. Termination of Ni(II) addition led to almost full recovery of the bioactivity in microorganisms as shown in the increase of specific oxygen uptake rate (SOUR) and SBR treatment performance

Two separate regulatory systems participate in control of swarming motility of Serratia liquefaciens MG1

DEFF Research Database (Denmark)

Givskov, M; Ostling, J; Eberl, L

1998-01-01

Swarming motility of Serratia liquefaciens MG1 requires the expression of two genetic loci, flhDC and swrI. Here we demonstrate that the products of the flhDC operon (the flagellar master regulator) and the swrI gene (the extracellular signal molecule N-butanoyl-L-homoserine lactone) are global...

Pinning in high performance MgB{sub 2} thin films and bulks: Role of Mg-B-O nano-scale inhomogeneities

Energy Technology Data Exchange (ETDEWEB)

Prikhna, Tatiana, E-mail: prikhna@mail.ru [Institute for Superhard Materials of the National Academy of Sciences of Ukraine , 2, Avtozavodskaya Str. , Kiev 07074 (Ukraine); Shapovalov, Andrey [Institute for Superhard Materials of the National Academy of Sciences of Ukraine , 2, Avtozavodskaya Str. , Kiev 07074 (Ukraine); Eisterer, Michael [Atominstitut, Vienna University of Technology, Stadionallee 2, 1020 Vienna (Austria); Shaternik, Vladimir [G.V. Kurdyumov Institute for Metal Physics of the National Academy of Sciences of Ukraine, 36 Academician Vernadsky blvd., Kiev, 03680 (Ukraine); Goldacker, Wilfried [Karlsruhe Institute of Technology (KIT), 76344 Eggenstein (Germany); Weber, Harald W. [Atominstitut, Vienna University of Technology, Stadionallee 2, 1020 Vienna (Austria); Moshchil, Viktor; Kozyrev, Artem; Sverdun, Vladimir [Institute for Superhard Materials of the National Academy of Sciences of Ukraine , 2, Avtozavodskaya Str. , Kiev 07074 (Ukraine); Boutko, Viktor [Donetsk Institute for Physics and Engineering named after O.O. Galkin of the National Academy of Sciences of Ukraine, R. Luxemburg str.72, Donetsk-114, 83114 (Ukraine); Grechnev, Gennadiy [B. Verkin Institute for Low Temperature Physics of the National Academy of Sciences of Ukraine, 47, Prospekt Nauky, Kharkiv 61103 (Ukraine); Gusev, Alexandr [Donetsk Institute for Physics and Engineering named after O.O. Galkin of the National Academy of Sciences of Ukraine, R. Luxemburg str.72, Donetsk-114, 83114 (Ukraine); Kovylaev, Valeriy; Shaternik, Anton [Institute for Superhard Materials of the National Academy of Sciences of Ukraine , 2, Avtozavodskaya Str. , Kiev 07074 (Ukraine)

2017-02-15

Highlights: • Pinning in MgB{sub 2} depends on the Mg-B-O nano-scaled inhomogeneities. • Finer oxygen-enriched inhomogeneities is the reason of the higher J{sub c} in MgB{sub 2} thin films as compared to bulk. • The results of DOS calculations for MgB{sub 2-x}O{sub x} compounds demonstrate that they have metal-like behavior. • Ordered oxygen distribution in MgB{sub 2} (in pairs or zigzags) reduces binding energy. - Abstract: The comparison of nano-crystalline MgB{sub 2} oxygen-containing thin film (140 nm) and highly dense bulk materials showed that the critical current density, J{sub c}, depends on the distribution of Mg-B-O nano-scale inhomogeneities. It has been shown that MgB{sub 2} bulks with high J{sub c} in low (∼10{sup 6} A/cm{sup 2} in 0-1 T at 10 K) and medium magnetic fields contain MgB{sub 0.6-0.8}O{sub 0.8-0.9} nano-inclusions, where δT{sub c} or a combined δT{sub c} (dominant) / δ{sub l} pinning mechanism prevails, while in bulk MgB{sub 2} with high J{sub c} in high magnetic fields (B{sub irr}(18.5 K) = 15 T, B{sub c2}(0 K) = 42.1 T) MgB{sub 1.2-2.7}O{sub 1.8-2.5} nano-layers are present and δ{sub l} pinning prevails. The structure of oxygen-containing films with high J{sub c} in low and high magnetic fields (J{sub c} (0 T) = 1.8 × 10{sup 7} A/cm{sup 2} and J{sub c} (5 T) = 2 × 10{sup 6} A/cm{sup 2} at 10 K) contains very fine oxygen-enriched Mg-B-O inhomogeneities and δ{sub l} pinning is realized. The results of DOS calculations in MgB{sub 2-x}O{sub x} cells for x = 0, 0.125, 0.25, 0.5, 1 demonstrate that all compounds are conductors with metal-like behaviour. In the case of ordered oxygen substitution for boron the binding energy, E{sub b}, does not increase sufficiently as compared with that for MgB{sub 2}, while when oxygen atoms form zigzag chains the calculated E{sub b} is even lower (E{sub b} = −1.15712 Ry).

Plasma l-citrulline concentrations in l-arginine-supplemented healthy dogs.

Science.gov (United States)

Flynn, K M; Kellihan, H B; Trepanier, L A

2017-08-01

To determine whether oral l-arginine increases plasma [l-citrulline] in dogs. Eleven healthy staff-owned dogs were used in this study. Dogs (n = 3) were given l-arginine (50mg/kg PO q8h) for 7 days, and plasma [l-arginine] and [l-citrulline] were analyzed by high performance liquid chromatography at baseline (BL), steady state trough, and 0.5, 1, 1.5, 2, 4, 6, and 8 h after final dosing on day 7. Eleven dogs were then treated with 100mg/kg l-arginine PO q8h for 7 days, and [l-arginine] and [l-citrulline] were measured at BL, steady state trough, and at peak 4 hrs after dosing (T4 hrs). - Plasma [l-arginine] and [l-citrulline] peaked at T4 hrs on the 50mg/kg dosage. Target outcome, modeled after human study results, of a doubling of [l-arginine] and a 25-30% increase in [l-citrulline] from BL were not reached. After the 100mg/kg dosage, plasma [l-arginine] increased from a BL median of 160.1 μM (range, 100.2-231.4 μM) to a peak of 417.4 μM (206.5-807.3 μM) at T4 hrs, and plasma [l-citrulline] increased from a BL median of 87.8 μM (59.1-117.1 μM) to peak of 102.2 μM (47.4-192.6 μM) at T4 hrs. Ten of eleven dogs showed a doubling of plasma [l-arginine] and 4/11 dogs achieved 25-30% or greater increases in plasma [l-citrulline]. No adverse effects on heart rate or blood pressure were noted. - Oral l-arginine dosage of 100mg/kg q8h doubles plasma [l-arginine] in healthy dogs, but conversion to l-citrulline is quite variable. Further evaluation of this dosage regimen in dogs with pulmonary hypertension is warranted. Copyright © 2017 Elsevier B.V. All rights reserved.

[Prerenal kidney failure in type 1 diabetes mellitus].

Science.gov (United States)

Schloot, N C; Hübinger, A; Scherbaum, W A

2003-12-05

A 22-year-old man was admitted in a severely reduced condition. Type 1 diabetes mellitus had been diagnosed when he was 13 years old, hypothyroidism was treated with L-thyroxine for 2 years. For the past 3 years he suffered from repetitive hypoglycemia, combined with vertigo, weakness and low blood pressure. He presented with hypotension and hyperpigmentation of the skin. Pathological laboratory results were: serum creatinine 2.5 mg/dl; urea 145 mg/dl; sodium 124 mmol/l; potassium 8.3 mmol/l, HbA (1c) 9.1%. The ECG showed large T waves. Additionally, plasma aldosterone was decreased (diabetes mellitus type 1 and hypothyroidism (Schmidt-Carpenter-Syndrome) were diagnosed. Initially, the patient was treated with sodium chloride 0.9% i. v. and oral sodium 5 g 4 times/day. In addition, he was given hydrocortisone 100 mg i. v., and then switched to 40 mg per day (20-10-10 mg), fludrocortisone 0.05 mg/ day and L-thyroxine 75 microg/ day orally the clinical condition improved dramatically within 24 hours. Intensified conventional insulin therapy was continued. In patients with type 1 diabetes, especially in combination with associated organ-specific autoimmune diseases, autoimmune polyglandular syndrome should be considered and adequately treated with those hormones that are reduced.

Volumizing effects of a smooth, highly cohesive, viscous 20-mg/mL hyaluronic acid volumizing filler: prospective European study

Directory of Open Access Journals (Sweden)

Hoffmann Klaus

2009-08-01

Full Text Available Abstract Background Facial volume loss contributes significantly to facial aging. The 20-mg/mL hyaluronic acid (HA formulation used in this study is a smooth, highly cohesive, viscous, fully reversible, volumizing filler indicated to restore facial volume. This first prospective study evaluated use in current aesthetic clinical practice. Methods A pan-European evaluation conducted under guidelines of the World Association of Opinion and Marketing Research, the trial comprised a baseline visit (visit 1 and a follow-up (visit 2 at 14 ± 7 days posttreatment. Physicians photographed patients at each visit. Each patient was treated with the 20-mg/mL HA volumizing filler as supplied in standard packaging. Procedural details, aesthetic outcomes, safety, and physician and patient ratings of their experience were recorded. Results Fifteen physicians and 70 patients (91% female; mean age: 50 years participated. Mean volume loss at baseline was 3.7 (moderate on the Facial Volume Loss Scale. Local anesthesia was used in 64.3% of cases. Most injections (85% were administered with needles rather than cannulas. Of the 208 injections, 59% were in the malar region, primarily above the periosteum. Subcutaneous injections were most common for other sites. The mean total injection volume per patient was 4.6 mL. The mean volume loss score declined significantly (P Conclusion The 20-mg/mL smooth, highly cohesive, viscous, volumizing HA filler was effective, well tolerated, and easy to use in current clinical practice. Participants were very likely to recommend this product to colleagues and friends, and patients would be very or quite likely to request this product for future treatments.

Effet du Mg et des oligo-éléments sur le comportement de cinq variétés d'arachides (Arachis hypogeae L.

Directory of Open Access Journals (Sweden)

Lumpungu, K.

1987-01-01

Full Text Available Effect of magnesium and trace elements on the development of five groundnut varieties (Arachis hypogeae L.. A study of Mg and certain minor elements (B, Cu, Fe, Mn, Mo and Zn given by seed imbibition has been conducted. The results have shown that the effect of Mg and minor elements on the growth, yield (pods and seeds and lipids content of the seeds depend on the variety and rate of Mg and minor elements application.

Behavior of methyl orange and orange 10 (orange G) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe; Comportamiento de naranja de metilo y naranja 10 (orange G) en presencia de compuestos tipo hidrotalcita de mg/Al y Mg/Fe

Energy Technology Data Exchange (ETDEWEB)

Cruz N, G.

2015-07-01

This work is focused on studying the sorption capacity of methyl orange dye (Nm) and orange 10 (N-10) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe uncalcined and calcined previously at 500 degrees Celsius. Sorption isotherms were determined and the study of the kinetics of sorption was performed. The materials were characterized before and after sorption processes of these dyes by X-ray diffraction, scanning electron microscopy, the specific surface area determination by the Brunauer-Emmett-Teller method, thermogravimetry coupled to mass and infrared spectrometry. The hydrotalcite type compounds reported in this paper were prepared in the laboratory and their acronyms are: HTMgAlG1, HTMgAlMO, HTMgFeG1 and HTMgFeG2. Note that in this work the best conditions for preparing compounds of Mg/Fe were found. From patterns of X-ray diffraction was identified the typical crystal structure of the hydrotalcite type compounds. By scanning electron microscopy the morphology could be determined in the form of flakes characteristics of these compounds. Likewise with elemental analysis of energy dispersive X-ray spectroscopy the presence of Mg, Al, Fe and C, elements of interest for this study was determined. The compounds presented a specific surface area relatively high from 80 to 120 m{sup 2}/g. Thermogravimetry results presented spectra of mass loss very characteristic associated to water losses, dehydroxylation and decarboxylation. The characteristic bands of water and carbonate were assigned by infrared spectroscopy and the bands corresponding to the dyes sulfonates were identified only for the calcined materials. The sorption capacities found of these compounds were as follows: for Nm in the compound HTMgAlG1 uncalcined was 17.82 mg/g for an initial concentration of 200 mg/L and for calcined (HTMgAlMOcal) of 99.8 mg/g with and initial concentration of 1000 mg/L. Moreover, the sorption capacity of the dye N-10 in this same material was 17.92 mg/g and 99

Effects of trace Be and Sc addition on the thermal stability of Al–7Si–0.6Mg alloys

Energy Technology Data Exchange (ETDEWEB)

Tzeng, Yu-Chih [Department of Mechanical Engineering, National Central University, Jhongli, Taiwan (China); Wu, Chih-Ting [Department of Vehicle Engineering, Army Academy R.O.C., Jhongli, Taiwan (China); Yang, Cheng-Hsien [Institute of Materials Science and Engineering, National Central University, Jhongli, Taiwan (China); Lee, Sheng-Long, E-mail: shenglon@cc.ncu.edu.tw [Department of Mechanical Engineering, National Central University, Jhongli, Taiwan (China)

2014-09-22

In the present study, the effects of trace amounts of beryllium (Be, 0.05 wt%) and scandium (Sc, 0.04 wt%) addition on the microstructures and thermal stability of Al–7Si–0.6Mg alloys were investigated. The results show that traces of Be and Sc significantly reduce the amount of the iron-bearing phase and the interdendritic shrinkage. Be transformed the acicular iron-bearing phases into the nodular Al–Fe–Si iron-bearing phase, which is less harmful to ductility. Moreover, the addition of Be increased the Mg content of the solid solution within the matrix, prompting greater precipitation of the metastable Mg{sub 2}Si phase after T6 heat treatment and effectively enhancing the mechanical properties of the alloy. However, during the following thermal exposure at 250 °C for 100 h, the metastable Mg{sub 2}Si phase grew into the coarse β-Mg{sub 2}Si equilibrium phase, resulting in a decrease in the mechanical strength of the alloy. Meanwhile, the addition of Sc had insignificant effect on the amount of metastable Mg{sub 2}Si phase that precipitated. However, here, the iron-bearing phase was a nodular Al{sub 12}Si{sub 6}Fe{sub 2}(Mg,Sc){sub 5} phase, which significantly enhanced the density of the castings. After the same thermal exposure procedure, it was remarkably found that the precipitation of fine Al{sub 3}Sc particles effectively inhibited grain growth and hindered the movement of dislocations. These factors led to the Sc-containing alloy having better mechanical properties (strength and ductility) than the alloys without Sc or with Be during the following thermal exposure at 250 °C.

Biotransformation of artemisinin using cell suspension cultures of Catharanthus roseus (L.) G.Don and Lavandula officinalis L.

Science.gov (United States)

Patel, Suman; Gaur, Rashmi; Verma, Priyanka; Bhakuni, Rajendra S; Mathur, Archana

2010-08-01

Artemisinin, an antimalarial compound, at 5 mg/40 ml, was transformed by cell suspension cultures of Catharanthus roseus (L.) G.Don and Lavandula officinalis L. into deoxyartemisinin with yields >78% (3.93 mg deoxyartemisinin from 5 mg artemisinin). Maximum conversion (78.6 and 78%) occurred after 6 and 7 days of adding artemisinin to 20 and 9 days old cultures of C. roseus and L. officinalis, respectively. The procedure was scaled up by and 500 mg artemisinin was transformed into 390 mg deoxyartemisinin. Addition of artemisinin at the beginning of the culture cycle resulted in >50% reduction in dry biomass production with no bioconversion. Conversion of artemisinin occurred intracellularly followed by leaching of the product into the medium.

Growth and Yield Stimulation of Winter Oilseed Rape (Brasssica Napus L. by Mg-Titanit Fertiliser

Directory of Open Access Journals (Sweden)

Kováčik Peter

2014-12-01

Full Text Available The effort to achieve higher yields at the required qualitative level has led to the intensive studying the problems of the rational usage of the titanium containing fertilisers by the agricultural research in the course the previous thirty years. Therefore, the objective of the experiment was to evaluate the impact of two doses of Mg-Titanit (0.2 l/ha and 0.4 l/ha on the formation of the aboveground and underground phytomass, also on the total chlorophyll in leaves, on the titanium and nitrogen content in the seeds and straw, on the quantity and quality of winter rape yield. The doses were applied two or three times on the leaves of winter rape (BBCH 50-52, BBCH 59, BBCH 66-67. The experiment was realized on the Haplic Chernozem (48°42´ N, 17°70´ E - Western Slovakia during two farming years (2009/2010 and 2010/2011. The results showed that all three applications of Mg-Titanit in both doses stimulated the formation of aboveground and underground phytomass of winter rape. The highest growth of phytomass was detected after the second application. The application of Mg-Titanit in the growth phases BBCH 50-52 and BBCH 59 increased the contents of both chlorophylls (a and b, where the growth of chlorophyll b content was more considerable than the growth of chlorophyll a content. The third spraying by Mg-Titanit decreased the content of the total chlorophyll. The application of Mg-Titanit had the positive impact on the yield of seeds, straw and fat content in the winter oilseed rape seeds.

Structural and optical properties of ZnMgO nanostructures formed by Mg in-diffused ZnO nanowires

International Nuclear Information System (INIS)

Pan, C.-J.; Hsu, H.-C.; Cheng, H.-M.; Wu, C.-Y.; Hsieh, W.-F.

2007-01-01

ZnMgO nanostructures with wurtzite phase were prepared by thermal diffusion of Mg into the ZnO nanowires. As ZnO light-emitting devices have been operated by using ZnMgO layers as energy barrier layers to confine the carriers, it is essential to realize the characterization of ZnMgO particularly. In this work, the Mg content in Zn 1 -x Mg x O alloy determined by X-ray diffraction (XRD) and photoluminescence (PL) shows a good coincidence. The variation of lattice constant and the blueshift of near-band-edge emission indicate that Zn 2+ ions are successfully substituted by Mg 2+ ions in the ZnO lattice. In Raman-scattering studies, the change of E 2 (high) phonon line shape in ZnO:Mg nanostructures reveals the microscopic substitutional disorder. In addition to the host phonons of ZnO, two additional bands around 383 and 510 cm -1 are presumably attributed to the Mg-related vibrational modes. - Graphical abstract: We reported the synthesis of the ZnMgO nanostructures prepared by a simple vapor transport method. Magnesium-related anomalous modes are observed by Raman spectra for the first time in ZnMgO system

Influence of boron addition on the grain refinement and mechanical properties of AZ91 Mg alloy

International Nuclear Information System (INIS)

Suresh, M.; Srinivasan, A.; Ravi, K.R.; Pillai, U.T.S.; Pai, B.C.

2009-01-01

This article reports the effect of boron addition on the grain refinement efficiency and mechanical properties of AZ91 magnesium alloy. The results show that the addition of boron in the form of Al-4B master alloy, significantly refines the grain size of AZ91 alloy. This refinement is due to the presence of AlB 2 particles, which act as potential nucleants for Mg grains. Improved mechanical properties are obtained with the addition of boron due to the finer grains.

Propagation of goldenrod (Solidago canadensis L. from leaf and nodal explants

Directory of Open Access Journals (Sweden)

Jun Li

2012-02-01

Full Text Available Goldenrod (Solidago canadensis L. is an invasive plant species in many countries except North America but a cut-flower species worldwide. There is a need to generate and propagate goldenrod clones efficiently for research and commercial purposes. A callus induction and plantlet regeneration system was developed by studying the influence of explant type and different concentrations of plant growth regulators. The highest callus production from leaf segments was obtained on Murashige and Skoog’s medium (MS medium supplemented with 1.0 mg/L naphthalene acetic acid (NAA and 1.0 mg/L 6-benzylaminopurine (BA. Adventitious shoots could be regenerated directly from leaf explants without an intermediate callus phase with the highest shoot induction percentage of 87.2%. The largest number of adventitious shoots per leaf explant (3.2 was obtained on MS medium supplemented with 0.4 mg/L NAA and 2.0 mg/L BA. MS medium supplemented with 0.1 mg/L NAA and 1.0 mg/L BA was the best medium for axillary shoot regeneration from nodal segments. The highest root number and longest roots occurred on half-strength MS without the addition of any growth regulator. Rooted plantlets were then transferred to a soil-based growth medium, placed in a greenhouse, and acclimatized with 100% success. All surviving plants grew normally without showing any morphological varia­tion when compared to those grow from seed. This regeneration protocol may be used to produce certain biotypes of goldenrod suitable for genetic transformation rapid propagation of goldenrod for commercial purposes or for screening fungi and toxins as potential biocontrol agents against this weed.

High performance microbiological transformation of L-tyrosine to L-dopa by Yarrowia lipolytica NRRL-143

Directory of Open Access Journals (Sweden)

Shultz Jeffry L

2007-08-01

Full Text Available Abstract Background The 3,4-dihydroxy phenyl L-alanine (L-dopa is a drug of choice for Parkinson's disease, controlling changes in energy metabolism enzymes of the myocardium following neurogenic injury. Aspergillus oryzae is commonly used for L-dopa production; however, potential improvements in ease of handling, growth rate and environmental impact have led to an interest in exploiting alternative yeasts. The two important elements required for L-dopa production are intracellular tyrosinases (thus pre-grown yeast cells are required for the transformation of L-tyrosine to L-dopa and L-ascorbate, which acts as a reducing agent. Results Pre-grown cells of Yarrowia lipolytica NRRL-143 were used for the microbiological transformation of L-tyrosine to L-dopa. Different diatomite concentrations (0.5–3.0 mg/ml were added to the acidic (pH 3.5 reaction mixture. Maximum L-dopa biosynthesis (2.96 mg/ml L-dopa from 2.68 mg/ml L-tyrosine was obtained when 2.0 mg/ml diatomite was added 15 min after the start of the reaction. After optimizing reaction time (30 min, and yeast cell concentration (2.5 mg/ml, an overall 12.5 fold higher L-dopa production rate was observed when compared to the control. Significant enhancements in Yp/s, Qs and qs over the control were observed. Conclusion Diatomite (2.0 mg/ml addition 15 min after reaction commencement improved microbiological transformation of L-tyrosine to L-dopa (3.48 mg/ml; p ≤ 0.05 by Y. lipolytica NRRL-143. A 35% higher substrate conversion rate was achieved when compared to the control.

Bog bilberry (Vaccinium uliginosum L.) extract reduces cultured Hep-G2, Caco-2, and 3T3-L1 cell viability, affects cell cycle progression, and has variable effects on membrane permeability.

Science.gov (United States)

Liu, Jia; Zhang, Wei; Jing, Hao; Popovich, David G

2010-04-01

Bog bilberry (Vaccinium uliginosum L.) is a blue-pigmented edible berry related to bilberry (Vaccinium myrtillus L.) and the common blueberry (Vaccinium corymbosum). The objective of this study was to investigate the effect of a bog bilberry anthocyanin extract (BBAE) on cell growth, membrane permeability, and cell cycle of 2 malignant cancer cell lines, Caco-2 and Hep-G2, and a nonmalignant murine 3T3-L1 cell line. BBAE contained 3 identified anthocyanins. The most abundant anthocyanin was cyanidin-3-glucoside (140.9 +/- 2.6 microg/mg of dry weight), followed by malvidin-3-glucoside (10.3 +/- 0.3 microg/mg) and malvidin-3-galactoside (8.1 +/- 0.4 microg/mg). Hep-G2 LC50 was calculated to be 0.563 +/- 0.04 mg/mL, Caco-2 LC50 was 0.390 +/- 0.30 mg/mL and 0.214 +/- 0.02 mg/mL for 3T3-L1 cells. LDH release, a marker of membrane permeability, was significantly increased in Hep-G2 cells and Caco-2 cells after 48 and 72 h compared to 24 h. The increase was 21% at 48 h and 57% at 72 h in Caco-2 cells and 66% and 139% in Hep-G2 cells compared to 24 h. However, 3T3-L1 cells showed an unexpected significant lower LDH activity (P < or = 0.05) after 72 h of exposure corresponding to a 21% reduction in LDH release. BBAE treatment increased sub-G1 in all 3 cell lines without influencing cells in the G2/M phase. BBAE treatment reduced the growth and increased the accumulation of sub-G1 cells in 2 malignant and 1 nonmalignant cell line; however, the effect on membrane permeability differs considerably between the malignant and nonmalignant cells and may in part be due to differences in cellular membrane composition.

Corrosion resistance of API 5L grade B steel with taro leaf (Colocasia esculenta) addition as corrosion inhibitor in HCl 0.1 M

Science.gov (United States)

Lestari, Yulinda; Priyotomo, Gadang

2018-05-01

Taro leaf (Colocasia esculenta) has the potential to be used as a corrosion inhibitor because it has a substance called polyphenol that binds to the hydroxyl group and essential amino acids. Taro leaf extract is taken by maceration method. In this study, the specimen was steel API 5L grade B that would measured the corosivity in 0.1 M HCl solution + taro leaf extract with a specific concentration (in ppm). Tests conducted by FTIR method taro leaves, potentiodynamic polarization (Tafel) and Electrochemical Impedance Spectroscopy (EIS). Based on the results revealed that there is a phenolic group in taro leaves, which has polyphenol content 0.053 % (mg/100 mg). The optimum composition of taro leaf extract is 4000 ppm which generate corrosion rate value of 30.22 mpy and efficiency inhibitor performance of 72.7 %. In this study, the Kads value of taro leaf extract ranged from 0.885 to greater than Kads value of ginger extract in hydrochloric acid solution. The high Kads values indicate a more efficient process of adsorption and better value of inhibition efficiency.

Inhibitory effects of ethyl acetate-soluble fraction from morus alba on lipid accumulation in 3T3-L1 cells.

Science.gov (United States)

Park, Hee-Sook; Shim, Soon-Mi; Kim, Gun-Hee

2013-11-01

Fruits of mulberry (Morus alba) have been widely used for therapeutic purposes in Asian countries for centuries. Treatment of 3T3-L1 cells with ethanolic extracts of M. alba decreased adipocyte differentiation at 100 microg/mL by 18.6%. Treatment suppressed mRNA levels of PPARgamma and C/EBPalpha expression in 3T3-L1 cells. However, the extract did not change free glycerol release from mature adipocytes. Thus, M. alba inhibited lipid accumulation by regulating transcription factors in 3T3-L1 adipocytes without a lipolytic effect. Among the soluble- fractions, the ethyl acetate-soluble fraction had the highest antiadipogenic effects on 3T3-L1 cells. This fraction decreasing intracellular lipid accumulation by 38.5% in response to treatment with 100 microg/mL. In addition, HPLC analysis of the ethyl acetate-soluble fraction of M. alba contained 167.7 microM of protocatechulic acid in 1 mg/mL of fraction, which inhibited lipid accumulation by 44.8% in response to treatment with 100 microM. From these results, M. alba is a possible candidate for regulating lipid accumulation in obesity.

The effects of L-arginine, D-arginine, L-name and methylene blue on channa striatus-induced peripheral antinociception in mice.

Science.gov (United States)

Zakaria, Zainul Amiruddin; Sulaiman, Mohd Rosian; Somchit, Muhammad Nazrul; Jais, Abdul Manan Mat; Ali, Daud Israf

2005-08-03

To determine the involvement of nitric oxide/cyclic guanosine monophosphate (NO/cGMP) pathway in aqueous supernatant of haruan (Channa striatus) fillet (ASH) antinociception using the acetic acid-induced abdominal constriction test. The ASH was prepared by soaking fresh haruan fillet in chloroform:methanol (CM) (2/1 (v/v)) for 72 h followed by evaporation of the upper layer supernatant to remove any solvent residues. The supernatant was then subjected to a freeze-drying process (48 h) followed by doses preparation. Subcutaneous (SC) administration of ASH alone (0.170, 0.426 and 1.704 mg/kg) exhibited a dose-dependent antinociception. On the other hand, 20 mg/kg (SC) of L-arginine and MB exhibited a significant nociception and antinociception, while D-arginine and L-NAME did not produce any effect at all. Pre-treatment with L-arginine was found to significantly reverse the three respective doses of ASH antinociception; pre-treatment with D-arginine did not produce any significant change in the ASH activity; pre-treatment with L-NAME only significantly increased the 0.170 and 0.426 mg/kg ASH antinociception; and pre-treatment with MB significantly enhanced the respective doses of ASH antinociception, respectively. Furthermore, co-treatment with L-NAME significantly enhanced the L-arginine reversal effect on 0.426 mg/kg ASH antinociception. In addition, MB significantly reversed the L-arginine nociception on 0.426 mg/kg ASH. These finding suggest ASH antinociception involves the nitric oxide (NO)/cyclic guanosine monophosphate (cGMP) pathway. The presence of NO was found to reverse ASH antinociceptive activity while blocking of cGMP system enhanced it.

COMBINED SPINAL EPIDURAL ANALGESIA IN LABOUR: COMPARISON OF BUPIVACAINE 1.25 MG WITH FENTANYL AND ROPIVACAINE 2.5 MG WITH FENTANYL INTRATHECAL

Directory of Open Access Journals (Sweden)

Prakash T. S. N

2016-10-01

with ASA I and ASA II in established labour with cervical dilatation less than 5 cm was selected and randomly allocated into two groups using closed envelope method. Informed written consent was taken from all participants. They were divided into 2 groups of 20 each. Group I received intrathecal Inj. Bupivacaine 1.25 mg and Inj. Fentanyl 20 µg. Group II received intrathecal Inj. Ropivacaine 2.5 mg and Inj. Fentanyl 20 µg for combined spinal epidural. IV line was secured with 18G cannula. Patient was preloaded with 500 mL of Hartmann’s solution. Basal vital parameter like pulse rate, blood pressure, respiration, O2 saturation were recorded. The patient was positioned in a sitting position with the help of an assistant. Under aseptic conditions, the back was prepared with 5% povidone-iodine solution, spirit and area was draped. L3-L4 interspace was identified. Skin was infiltrated with 2 mL of 1% Xylocaine. After infiltration of local anaesthetic by using needle through needle technique 18-gauge Tuohy needle, epidural space was identified with loss of resistance to air technique. Then, a 15 mm (27 G long ‘Whitacre’ spinal needle was introduced through the epidural needle and the correct position of the tip in the intrathecal space was confirmed by observation of free flow of CSF. Patients were allocated randomly to receive intrathecal injection of bupivacaine 1.25 mg (0.5% bupivacaine 0.25 mL with fentanyl 20 µg (Group I n=30 or ropivacaine 2.5 mg/0.2% ropivacaine 1.25 mL with fentanyl 20 µg (Group II, n=30 both made up to total volume of 2 mL with saline. Injection of intrathecal drug was completed in 10 secs., then 20G epidural catheter was threaded through the epidural needle into the epidural space in cephalad direction. The epidural needle was slowly pulled out without disturbing the catheter. About 3 to 5 cm of catheter was left in epidural space. The catheter was well secured with plaster. Patients vitals was recorded every 5, 10, 15, 30, 45, 60, 75, 90

Antiproliferative activity of aqueous leaf extract of Annona muricata L. on the prostate, BPH-1 cells, and some target genes.

Science.gov (United States)

Asare, George Awuku; Afriyie, Dan; Ngala, Robert A; Abutiate, Harry; Doku, Derek; Mahmood, Seidu A; Rahman, Habibur

2015-01-01

Annona muricata L. has been reported to possess antitumor and antiproliferative properties. Not much work has been done on its effect on BPH-1 cell lines, and no in vivo studies targeting the prostate organ exist. The study determined the effect of A muricata on human BPH-1 cells and prostate organ. The MTT assay was performed on BPH-1 cells using the aqueous leaf extract of A muricata. Cells (1 × 10(5) per well) were challenged with 0.5, 1.0, and 1.5 mg/mL extract for 24, 48, and 72 hours. Cell proliferation and morphology were examined microscopically. BPH-1 cells (1 × 10(4) per well) were seeded into 6-well plates and incubated for 48 hours with 0.5, 1.0, and 1.5 mg/mL A muricata extract. Reverse transcriptase polymerase chain reaction was performed using mRNA extracted from the cells. Possible target genes, Bax and Bcl-2, were examined. Twenty F344 male rats (≈200 g) were gavaged 30 mg/mL (10 rats) and 300 mg/mL (10 rats) and fed ad libitum alongside 10 control rats. Rats were sacrificed after 60 days. The prostate, seminal vesicles, and testes were harvested for histological examination. Annona muricata demonstrated antiproliferative effects with an IC50 of 1.36 mg/mL. Best results were obtained after 48 hours, with near cell extinction at 72 hours. Bax gene was upregulated, while Bcl-2 was downregulated. Normal histological architecture was observed for all testes. Seminal vesicle was significantly reduced in test groups (P BPH-1 cells and reduces prostate size, possibly through apoptosis. © The Author(s) 2014.

Effects of minor Zr and Sr on as-cast microstructure and mechanical properties of Mg-3Ce-1.2Mn-0.9Sc (wt.%) magnesium alloy

International Nuclear Information System (INIS)

Pan Fusheng; Yang Mingbo; Shen Jia; Wu Lu

2011-01-01

Research highlights: → Minor Zr and/or Sr additions can effectively refine the grains of the Mg-3Ce-1.2Mn-0.9Sc alloy. → Minor Zr and/or Sr additions can improve the tensile properties of the Mg-3Ce-1.2Mn-0.9Sc alloy. → Minor Zr and/or Sr additions can improve the creep properties of the Mg-3Ce-1.2Mn-0.9Sc alloy. - Abstract: The effects of minor Zr and Sr on the as-cast microstructure and mechanical properties of the Mg-3Ce-1.2Mn-0.9Sc (wt.%) alloy were investigated by using optical and electron microscopies, differential scanning calorimetry (DSC) analysis, and tensile and creep tests. The results indicate that adding minor Zr and/or Sr to the Mg-3Ce-1.2Mn-0.9Sc alloy does not cause an obvious change in the morphology and distribution of the Mg 12 Ce phase. However, the grains of the Zr and/or Sr-containing alloys are effectively refined. Among the Zr and/or Sr-containing alloys, the grains of the alloy with the addition of 0.5 wt.%Zr + 0.1 wt.%Sr are the finest, followed by the alloys with the additions of 0.5 wt.%Zr and 0.1 wt.%Sr, respectively. In addition, small additions of Zr and/or Sr can improve the tensile and creep properties of the Mg-3Ce-1.2Mn-0.9Sc alloy. Among the Zr and/or Sr-containing alloys, the alloy with the addition of 0.5 wt.%Zr + 0.1 wt.%Sr obtains the optimum tensile and creep properties.

Biochemical Evidence of L-Dopa Synthesis in a Cytokine-Resilient Aspergillus oryzae

International Nuclear Information System (INIS)

Ali, S.; Saleem, R.

2016-01-01

The present work describes the microbiological production of 3,4 dihydroxy-L-phenylalanine (L-dopa) from a cytokine-inhibited mold culture of Aspergillus oryzae (strain Ck-R6). A level of 15 μg/ml cytokine was found optimal for culture resistance and better dopa-dopamine activity. Synthetic L-tyrosine was used as a basal carbon source. The aerobic reactions were carried out using pre-grown mycelia as a direct tyrosinase source. The mycelia were cultivated using 200 ml of GPY mineral-salt medium and developed at 30 degree C for 48 h (240 rpm) in 500 ml Erlenmeyer flasks. L-dopa production was found optimal when L-ascorbic acid (5 mg/ml) was added 6 min after starting the reaction (120 rpm). The maximal production (2.2 mg/ml L-dopa) was obtained when L-tyrosine concentration was 2.5 mg/ml. Mycelial level (75 mg/ml) and time of reaction (40 min) were also evaluated. L-Tyrosine consumption was found to be 2.1 mg/ml. After optimizing the reaction conditions, particularly L-ascorbic acid addition, a 30 percent improved L-dopa yield was achieved compared to control when the parameters including time of reaction (40 min), L-tyrosine concentration (2.5 mg/ml) and temperature (50 degree C) were optimized by two-factorial Plackett-Burman design (PBD). (author)

Concentrations of garenoxacin in plasma, bronchial mucosa, alveolar macrophages and epithelial lining fluid following a single oral 600 mg dose in healthy adult subjects.

Science.gov (United States)

Andrews, J; Honeybourne, D; Jevons, G; Boyce, M; Wise, R; Bello, A; Gajjar, D

2003-03-01

A microbiological assay was used to measure concentrations of garenoxacin (BMS-284756) in plasma, bronchial mucosa (BM), alveolar macrophages (AM) and epithelial lining fluid (ELF), following a single 600 mg oral dose. Twenty-four healthy subjects were allocated into four nominal time intervals after the dose, 2.5-3.5, 4.5-5.5, 10.5-11.5 and 23.5-24.5 h. Mean concentrations in plasma, BM, AM and ELF, respectively, for the four nominal time windows were for 2.5-3.5 h 10.0 mg/L (S.D. 2.8), 7.0 mg/kg (S.D. 1.3), 106.1 mg/L (S.D. 60.3) and 9.2 mg/L (S.D. 3.6); 4.5-5.5 h 8.7 mg/L (S.D. 2.2), 6.0 mg/kg (S.D. 1.9), 158.6 mg/L (S.D. 137.4) and 14.3 mg/L (S.D. 8.2); 10.5-11.5 h 6.1 mg/L (S.D. 1.9), 4.0 mg/kg (S.D. 1.4), 76.0 mg/L (S.D. 47.7) and 7.9 mg/L (S.D. 4.6); and 23.5-24.5 h 2.1 mg/L (S.D. 0.5), 1.7 mg/kg (S.D. 0.7), 30.7 mg/L (S.D. 12.9) and 3.3 mg/L (S.D. 2.3). Concentrations at all sites exceeded MIC(90)s for the common respiratory pathogens Haemophilus influenzae (0.03 mg/L), Moraxella catarrhalis (0.015 mg/L) and Streptococcus pneumoniae (0.06 mg/L). These data suggest that garenoxacin should be effective in the treatment of community-acquired pneumonia and chronic obstructive pulmonary disease.

Superconducting properties of MgB2 particle impregnated with Mg-based alloys

International Nuclear Information System (INIS)

Shimizu, Yusuke; Matsuda, Kenji; Mizutani, Manabu; Nishimura, Katsuhiko; Kawabata, Tokimasa; Ikeno, Susumu; Hishinuma, Yoshimitsu; Aoyama, Shigeki

2011-01-01

The three-dimensional penetration method combined with semi-solid casting (SS-3DPC) was utilized to prepare magnesium diboride (MgB 2 ) powder composite materials with various host materials of Mg, Mg-3%Al, Mg-3%Al-1%Zn, Mg-9%Al, and Mg-9%Al-1%Zn. X-ray diffraction measurements indicated predominant peak patterns of MgB 2 and a host alloy, implying that the host material tightly bonded MgB 2 grains without melting the MgB 2 powder. This was confirmed by SEM images. Measured electrical resistivity and magnetization versus temperature showed clear signals of superconducting transition temperature of 27-38 K for all the samples cut out from the billets. Magnetic hysteresis loop observed at 5 K enabled us to estimate a critical current density (J c ) based on the extended Bean model. Additions of aluminum and zinc elements to magnesium host-matrix were found to enhance J c and increase residual resistivity (ρ 0 ) suggesting that aluminum and zinc have an effect on pinning magnetic flux flow for J c enhancement, and scattering conduction electrons for increase of ρ 0 . (author)

Chemical, Antioxidant and Antimicrobial Investigations of Pinus cembra L. Bark and Needles

Directory of Open Access Journals (Sweden)

Anca Miron

2011-09-01

Full Text Available The chemical constituents and biological activity of Pinus cembra L. (Pinaceae, native to the Central European Alps and the Carpathian Mountains, are not well known. The aim of the present work was to examine the phenolic content, antioxidant and antimicrobial effects of hydromethanolic extracts of Pinus cembra L. bark and needles. Bark extract had higher concentrations of total phenolics (299.3 vs. 78.22 mg gallic acid equivalents/g extract, flavonoids (125.3 vs. 19.84 mg catechin equivalents/g extract and proanthocyanidins (74.3 vs. 12.7 mg cyanidin equivalents/g extract than needle extract and was more active as a free radical scavenger, reducing agent and antimicrobial agent. The EC50 values in the 2,2-diphenyl-1-picrylhydrazyl (DPPH, 2,2'-azino-bis(3-ethylbenzo-thiazoline-6-sulfonic acid diammonium salt (ABTS and reducing power assays were 71.1, 6.3 and 26 mg/mL for bark extract and 186.1, 24 and 104 mg/mL for needle extract, respectively. In addition, needle extract showed ferrous ions chelating effects (EC50 = 1,755 μg/mL. The antimicrobial effects against Staphylococcus aureus, Sarcina lutea, Bacillus cereus, Escherichia coli, Pseudomonas aeruginosa and Candida albicans were assessed by the agar diffusion method. Both extracts (4 mg/well were active against all the microorganisms tested; bark extract showed higher inhibition on all strains. These results indicate that Pinus cembra L. bark and needles are good sources of phytochemicals with antioxidant and antimicrobial activities.

EFFECT OF CALCIUM ADDITION ON THE DEFLUORIDATION CAPACITY OF BONE CHAR

DEFF Research Database (Denmark)

Jacobsen, P.; Dahi, Elian

1997-01-01

Dosage of small amounts of calcium chloride to fluoride water prior to contact with bone char which has already been saturated with fluoride is shown to provide an additional fluoride removal capacity. The additionally obtained removal capacity increases with slower filtration velocities...... to be capable of reducing the fluoride concentration form 10 to about 0.5 mgF/L. The additionally saturated column is shown to be regenerated by simple adjustment of the pH of the water to 11 and allowing to flow for a few bed volumes. The useful regeneration capacity, where the fluoride concentration...... and increasing calcium dosage. A filtration velocity of 0.07 m/h, corresponding to a contact time of about 2 hours, and a dosage of 100 mgCa/L, are shown to provide an additional removal capacity of about 3 mgF/g, i.e. almost a doubling of the genuine removal capacity of the bone char. The process is shown...

Structure/property (constitutive and dynamic strength/damage) characterization of additively manufactured 316L SS

Science.gov (United States)

Gray, G. T., III; Livescu, V.; Rigg, P. A.; Trujillo, C. P.; Cady, C. M.; Chen, S. R.; Carpenter, J. S.; Lienert, T. J.; Fensin, S.

2015-09-01

For additive manufacturing (AM), the certification and qualification paradigm needs to evolve as there exists no "ASTM-type" additive manufacturing certified process or AM-material produced specifications. Accordingly, utilization of AM materials to meet engineering applications requires quantification of the constitutive properties of these evolving materials in comparison to conventionally-manufactured metals and alloys. Cylinders of 316L SS were produced using a LENS MR-7 laser additive manufacturing system from Optomec (Albuquerque, NM) equipped with a 1kW Yb-fiber laser. The microstructure of the AM-316L SS is detailed in both the as-built condition and following heat-treatments designed to obtain full recrystallization. The constitutive behavior as a function of strain rate and temperature is presented and compared to that of nominal annealed wrought 316L SS plate. The dynamic damage evolution and failure response of all three materials was probed using flyer-plate impact driven spallation experiments at a peak stress of 4.5 GPa to examine incipient spallation response. The spall strength of AM-produced 316L SS was found to be very similar for the peak shock stress studied to that of annealed wrought or AM-316L SS following recrystallization. The damage evolution as a function of microstructure was characterized using optical metallography.

High-Energy-Density Aqueous Magnesium-Ion Battery Based on a Carbon-Coated FeVO4 Anode and a Mg-OMS-1 Cathode.

Science.gov (United States)

Zhang, Hongyu; Ye, Ke; Zhu, Kai; Cang, Ruibai; Yan, Jun; Cheng, Kui; Wang, Guiling; Cao, Dianxue

2017-12-01

Porous FeVO 4 is prepared by hydrothermal method and further modified by coating with carbon to obtain FeVO 4 /C with a hierarchical pore structure. FeVO 4 /C is used as an anodic electrode in aqueous rechargeable magnesium-ion batteries. The FeVO 4 /C material not only has improved electrical conductivity as a result of the carbon coating layer, but also has an increased specific surface area as a result of the hierarchical pore structure, which is beneficial for magnesium-ion insertion/deinsertion. Therefore, an aqueous rechargeable magnesium-ion full battery is successfully constructed with FeVO 4 /C as the anode, Mg-OMS-1 (OMS=octahedral molecular sieves) as the cathode, and 1.0 mol L -1 MgSO 4 as the electrolyte. The discharge capacity of the Mg-OMS-1//FeVO 4 /C aqueous battery is 58.9 mAh g -1 at a current density of 100 mA g -1 ; this value is obtained by calculating the total mass of two electrodes and the capacity retention rate of this device is 97.7 % after 100 cycles, with almost 100 % coulombic efficiency, which indicates that the system has a good electrochemical reversibility. Additionally, this system can achieve a high energy density of 70.4 Wh kg -1 , which provides powerful evidence that an aqueous magnesium-ion battery is possible. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Are Vancomycin Trough Concentrations of 15 to 20 mg/L Associated With Increased Attainment of an AUC/MIC ≥ 400 in Patients With Presumed MRSA Infection?

Science.gov (United States)

Hale, Cory M; Seabury, Robert W; Steele, Jeffrey M; Darko, William; Miller, Christopher D

2017-06-01

To determine whether there is an association between higher vancomycin trough concentrations and attainment of a calculated area under the concentration-time curve (AUC)/minimum inhibitory concentration (MIC) ≥400. A retrospective analysis was conducted among vancomycin-treated adult patients with a positive methicillin-resistant Staphylococcus aureus (MRSA) culture. Attainment of a calculated AUC/MIC ≥400 was compared between patients with troughs in the reference range of 15 to 20 mg/L and those with troughs in the following ranges: 20 mg/L. Nephrotoxicity was assessed as a secondary outcome based on corrected average vancomycin troughs over 10 days of treatment. Overall, 226 patients were reviewed and 100 included. Relative to troughs ≥10, patients with vancomycin troughs AUC/MIC ≥400 (odds ratio [OR] 0.27, 95% confidence interval [CI]: 0.01-0.75). No difference was found in the attainment of an AUC/MIC ≥400 in patients with troughs of 10 to 14.9 mg/L and >20 mg/L when compared to patients with troughs of 15 to 20 mg/L. The mean corrected average vancomycin trough was higher in patients developing nephrotoxicity compared to those who did not (19.5 vs 14.5 mg/L, P AUC/MIC target relative to troughs of 10 to 14.9 mg/L but may increase nephrotoxicity risk.

Pile oscillator measurements of thermal absorption cross sections of Al, Mg, Fe and Cu; Mesure des sections efficaces thermiques d'absorption de l'Al, du Mg, du Fe et du Cu par la methode d'oscillation

Energy Technology Data Exchange (ETDEWEB)

Carre, J C; Vidal, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

The phase oscillation technique used at ZOE has the property of reducing of a marked factor the effect of neutron scattering by the sample. The absorption cross sections of poorly absorbing and highly scattering materials have been measured; for neutrons of 2,200 m/s, the following values are obtained: 229 {+-} 3 mb for Al; 64.2 {+-} 1.5 mb for Mg, 2.53 {+-} 0.03 b for Fe and 3.74 {+-} 0.04 b for Cu. (authors) [French] La methode d'oscillation de phase utilisee a ZOE possede la propriete de diminuer d'un facteur important l'influence de la diffusion. Les sections efficaces de capture de materiaux peu capturants et tres diffusants, ont ete mesurees; pour des neutrons de 2200 m/s, on obtient pour l'Al: 229 {+-} 3mb, pour le Mg: 64,2 {+-} 1,5 mb, pour le Fe: 2,53 {+-} 0,03 b et pour le Cu: 3,74 {+-} 0,04 b. (auteurs)

Improvement of corrosion resistance in NaOH solution and glass forming ability of as-cast Mg-based bulk metallic glasses by microalloying

Directory of Open Access Journals (Sweden)

Peng Hao

2011-02-01

Full Text Available The influences of the addition of Ag on the glass forming ability (GFA and corrosion behavior were investigated in the Mg-Ni-based alloy system by X-ray diffraction (XRD and electrochemical polarization in 0.1 mol/L NaOH solution. Results shows that the GFA of the Mg-Ni-based BMGs can be improved dramatically by the addition of an appropriate amount of Ag; and the addition element Ag can improve the corrosion resistance of Mg-Ni-based bulk metallic glass. The large difference in atomic size and large negative mixing enthalpy in alloy system can contribute to the high GFA. The addition element Ag improves the forming speed and the stability of the passive film, which is helpful to decrease the passivation current density and to improve the corrosion resistance of Mg-Ni-based bulk metallic glass.

Positron annihilation 2D-ACAR study of semi-coherent Li nanoclusters in MgO(1 0 0) and MgO(1 1 0)

International Nuclear Information System (INIS)

Falub, C.V.; Mijnarends, P.E.; Eijt, S.W.H.; Huis, M.A. van; Veen, A. van; Schut, H.

2002-01-01

Depth selective positron annihilation two-dimensional angular correlation of annihilation radiation (2D-ACAR) is used to determine the electronic structure of Li nanoclusters formed by implantation of 10 16 cm -2 6 Li ions (with an energy of 30 keV) in MgO(1 0 0) and (1 1 0) crystals, and subsequently annealed at 950 K. The 2D-ACAR spectra of Li-implanted MgO obtained with 4 keV positrons reveal the semi-coherent ordering state of the embedded metallic Li nanoclusters. The results agree with ab initio Korringa-Kohn-Rostoker calculations

Positron annihilation 2D-ACAR study of semi-coherent Li nanoclusters in MgO(1 0 0) and MgO(1 1 0)

Energy Technology Data Exchange (ETDEWEB)

Falub, C.V. E-mail: c.falub@iri.tudelft.nl; Mijnarends, P.E.; Eijt, S.W.H.; Huis, M.A. van; Veen, A. van; Schut, H

2002-05-01

Depth selective positron annihilation two-dimensional angular correlation of annihilation radiation (2D-ACAR) is used to determine the electronic structure of Li nanoclusters formed by implantation of 10{sup 16} cm{sup -2} {sup 6}Li ions (with an energy of 30 keV) in MgO(1 0 0) and (1 1 0) crystals, and subsequently annealed at 950 K. The 2D-ACAR spectra of Li-implanted MgO obtained with 4 keV positrons reveal the semi-coherent ordering state of the embedded metallic Li nanoclusters. The results agree with ab initio Korringa-Kohn-Rostoker calculations.

Positron annihilation 2D-ACAR study of semi-coherent Li nanoclusters in MgO( 1 0 0 ) and MgO( 1 1 0 )

Science.gov (United States)

Falub, C. V.; Mijnarends, P. E.; Eijt, S. W. H.; van Huis, M. A.; van Veen, A.; Schut, H.

2002-05-01

Depth selective positron annihilation two-dimensional angular correlation of annihilation radiation (2D-ACAR) is used to determine the electronic structure of Li nanoclusters formed by implantation of 10 16 cm -26Li ions (with an energy of 30 keV) in MgO(1 0 0) and (1 1 0) crystals, and subsequently annealed at 950 K. The 2D-ACAR spectra of Li-implanted MgO obtained with 4 keV positrons reveal the semi-coherent ordering state of the embedded metallic Li nanoclusters. The results agree with ab initio Korringa-Kohn-Rostoker calculations.

In-situ synchrotron x-ray study of MgB2 formation when doped by SiC

Science.gov (United States)

Abrahamsen, A. B.; Grivel, J.-C.; Andersen, N. H.; Herrmann, M.; Häßler, W.; Birajdar, B.; Eibl, O.; Saksl, K.

2008-02-01

We have studied the evolution of the reaction xMg + 2B + ySiC → zMg1-p(B1-qCq)2 + yMg2Si in samples of 1, 2, 5 and 10 wt% SiC doping. We found a coincident formation of MgB2 and Mg2Si, whereas the crystalline part of the SiC nano particles is not reacting at all. Evidence for incorporation of carbon into the MgB2 phase was established from the decrease of the a-axis lattice parameter upon increasing SiC doping. An estimate of the MgB2 lower limit grain size was found to decrease from L100 = 795 Å and L002 = 337 Å at 1 wt% SiC to L100 = 227 Å and L002= 60 Å at 10 wt% SiC. Thus superconductivity might be suppressed at 10 wt% SiC doping due to the grain size approaching the coherence length.

Effect of Ce-rich rare earth on microstructure and mechanical properties of Mg-10Zn-5Al-0.1Sb magnesium alloy

Directory of Open Access Journals (Sweden)

You Zhiyong

2012-05-01

Full Text Available To improve the comprehensive mechanical properties of Mg-10Zn-5Al-0.1Sb magnesium alloy, different amount of Ce-rich rare earth (RE was added to the alloy, and the effect of RE addition on the microstructure and mechanical properties of Mg-10Zn-5Al-0.1Sb alloy was investigated by means of Brinell hardness measurement, scanning electron microscopy (SEM, energy dispersive spectroscope (EDS and X-ray diffraction (XRD. The results show that an appropriate amount of Ce-rich rare earth addition can make the Al4Ce phase particles and CeSb phase disperse more evenly in the alloy. These phases refine the alloy抯 matrix and make the secondary phases [t-Mg32(Al,Zn49 phase and f-Al2Mg5Zn2 phase] finer and more dispersive, therefore significantly improve the mechanical properties of the Mg-10Zn-5Al-0.1Sb alloy. When the RE addition is 1.0 wt.%, the tensile strengths of the alloy both at room temperature and 150 篊 reach the maximum values while the impact toughness is slightly lower than that of the matrix alloy. The hardness increases with the increase of RE addition.

[Influences of ion-suppressors on retention behaviors of nine food additives in reversed-phase high performance liquid chromatographic separation].

Science.gov (United States)

Zhao, Yonggang; Chen, Xiaohong; Li, Xiaoping; Yao, Shanshan; Jin, Micong

2011-10-01

The influences of ion-suppressors on retention behaviors of nine food additives, i.e., acesulfame, saccharin, caffeine, aspartame, benzoic acid, sorbic acid, stevioside, dehydroacetic acid and neotame in reversed-phase high performance liquid chromatographic (RP-HPLC) separation were investigated. The organic modification effects of acids, i. e. , trifluoroacetic acid (TFA) and buffer salts, i. e. , TFA-ammonium acetate (AmAc) were studied emphatically. The relationships between retention factors of solutes and volume percentages of ion-suppressors in the mobile phase systems of acetonitrile-TFA aqueous solution and acetonitrile-TFA-AmAc aqueous solution were quantitatively established, separately. The separation of nine food additives was completed by a gradient elution with acetonitrile-TFA (0.01%, v/v)-AmAc (2. 5 mmol/L) aqueous solution as the mobile phases. An RP-HPLC method was established for the simultaneous determination of nine food additives in red wine. In the range of 10. 0 - 100. 0 mg/L, nine food additives showed good linearity with the correlation coefficients ( r2 ) larger than 0. 999 1. The limits of detection (LODs) were in the range of 0. 33 - 2. 36 mg/L and the limits of quantification (LOQs) were in the range of 1. 11 - 7. 80 mg/L. The spiked recoveries were between 87. 61% and 108. 4% with the relative standard deviations (RSDs) of 2. 2% -9. 4%. These results are of referential significance for the rapid establishment and accu- rate optimization of RP-HPLC separation for the simultaneous determination of food additives in other foods.

Inhibitory effects of food additives derived from polyphenols on staphylococcal enterotoxin A production and biofilm formation by Staphylococcus aureus.

Science.gov (United States)

Shimamura, Yuko; Hirai, Chikako; Sugiyama, Yuka; Shibata, Masaharu; Ozaki, Junya; Murata, Masatsune; Ohashi, Norio; Masuda, Shuichi

2017-12-01

In this study, we examined the inhibitory effects of 14 food additives derived from polyphenol samples on staphylococcal enterotoxin A (SEA) production and biofilm formation by Staphylococcus aureus. Tannic acid AL (TA), Purephenon 50 W (PP) and Polyphenon 70A (POP) at 0.25 mg/mL and Gravinol®-N (GN), Blackcurrant polyphenol AC10 (BP), and Resveratrol-P5 (RT) at 1.0 mg/mL significantly decreased SEA production by S. aureus C-29 (p Food additives derived from polyphenols have viability to be used as a means to inhibit the enterotoxin production and control the biofilm formation of foodborne pathogens.

Effects of additive Pd on the structures and electrochemical hydrogen storage properties of Mg{sub 67}Co{sub 33}-based composites or alloys with BCC phase

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yao; Zhuang, Xiangyang [School of Materials Science and Engineering, Southeast University, Nanjing 211189 (China); Zhu, Yunfeng [College of Materials Science and Engineering, Nanjing Tech University, 5 Xinmofan Road, Nanjing 210009 (China); Zhan, Leyu [School of Materials Science and Engineering, Southeast University, Nanjing 211189 (China); Pu, Zhenggan [College of Materials Science and Engineering, Nanjing Tech University, 5 Xinmofan Road, Nanjing 210009 (China); Wan, Neng [SEU-FEI Nano Pico Center, Key Laboratory of MEMS of Ministry of Education, School of Electronics Science and Engineering, Southeast University, Nanjing 210096 (China); Li, Liquan [College of Materials Science and Engineering, Nanjing Tech University, 5 Xinmofan Road, Nanjing 210009 (China)

2015-02-15

Highlights: • Additive Pd in Mg{sub 67}Co{sub 33} benefits to form a ternary BCC alloy. • Introducing 5.0 at.% Pd in Mg{sub 67}Co{sub 33} lifts the initial discharge capacity from 10 mAh/g to maximum 530 mAh/g. • Exchange current density was increased due to the homogeneously dispersed Pd. • Additive Pd slightly enhances the hydrogen diffusion coefficient of Mg-Co-Pd composites or alloys. - Abstract: Mg{sub 67}Co{sub 33} and Mg{sub 67}Co{sub 33}-Pd composites/alloys prepared by ball milling for 120 h possess nano-crystalline with body-centered cubic (BCC) structure, which was verified by high resolution transmission electron microscopy (HRTEM) and selected area electron diffraction (SAED) analyses. The introduced 5.0 at.% Pd significantly lifts the initial discharge capacity from 10 mAh g{sup -1} of Mg{sub 67}Co{sub 33} to maximum 530 mAh g{sup -1}. Pd also drives the Mg{sub 67}Co{sub 33}-Pd composite forming a full BCC alloy during ball milling. The distribution of Pd gradually becomes homogeneous with the augmentation of the ball milling time according to the analyses by scanning electron microscopy-energy dispersive spectrometer (SEM-EDS). Exchange current density increased with the milling time and can be ascribed to the homogeneously dispersion of Pd over the surface. The introduced Pd also enhances the hydrogen diffusion coefficient of the Mg{sub 67}Co{sub 33}-Pd composites/alloys.

Mg2+ Doped into Electro-synthesized HKUST-1 and Their Initial Hydrogen Sorption Properties

Science.gov (United States)

Lestari, W. W.; Ni'maturrohmah, D.; Arrozi, U. S. F.; Suwarno, H.

2018-01-01

The hydrogen storage materials are essentially play important roles in supporting the utilization of hydrogen as a promising alternative energy. Several innovative materials have been proposed and intensively investigated in this regard, including Metal-Organic Framework (MOFs). MOFs type HKUST-1 [Cu3(BTC)2] (BTC = benzene-tri-carboxylate) is the most explored materials in hydrogen storage. In this research, HKUST-1 was electro-synthesized under 15 volt for 1.5 h. This material was ex-situ modified with magnesium(II) ion with variation: 3, 5 and 10 wt% to add attractive sites for hydrogen to form Mg2+@HKUST-1. The final materials were characterized by XRD, FTIR, SEM-EDX, and SAA. Hydrogen sorption measurement was conducted using Sievert system at 30 and 80 °C with pressure from 0.2 to 1.5 bar in 10 minutes for each condition. According to XRD analysis, the basic structure of Mg2+@HKUST-1 was remaining stable. In contrary, SEM analysis showed that HKUST-1 morphology was changed after modification with Mg2+. In addition, the surface area of materials significantly increased from 372.112 to 757.617m2/g, based on SAA analysis. The presence of Mg2+ in the HKUST-1 increased the hydrogen sorption capacity up to 0.475 wt% at 1.4 bar at 30 °C and 0.256 wt% at 80 °C (1.4 bar).

Polymorphisms of vitamin K-related genes (EPHX1 and VKORC1L1) and stable warfarin doses.

Science.gov (United States)

Chung, Jee-Eun; Lee, Kyung Eun; Chang, Byung Chul; Gwak, Hye Sun

2018-01-30

The aim of this study was to investigate the possible effects of EPHX1 and VKORC1L1 polymorphisms on variability of responses to warfarin. Sixteen single nucleotide polymorphisms (SNPs) in 201 patients with stable warfarin doses were analyzed including genes of VKORC1, CYP2C9, CYP4F2, GGCX, EPHX1 and VKORC1L1. Univariate analysis was conducted for the association of genotypes with stable warfarin doses. Multiple linear regression analysis was used to investigate factors that independently affected the inter-individual variability of warfarin dose requirements. The rs4072879 of VKORC1L1 (A>G) was significantly associated with stable warfarin doses; wild homozygote carriers (AA) required significantly lower stable warfarin doses than those with the variant G allele (5.02±1.56 vs. 5.96±2.01mg; p=0.001). Multivariate analysis showed that EPHX1 rs1877724 and VKORC1L1 rs4072879 accounted for 1.5% and 1.3% of the warfarin dose variability. Adding EPHX1 and VKORC1L1 SNPs to the base model including non-genetic variables (operation age, body weight and the therapy of ACEI or ARB) and genetic variables (VKORC1 rs9934438, CYP2C9 rs1057910, and CYP4F2 rs2108622) gave a number needed to genotype of 34. This study showed that polymorphisms of EPHX1 and VKORC1L1 could be determinants of stable warfarin doses. Copyright © 2017. Published by Elsevier B.V.

Behavior of methyl orange and orange 10 (orange G) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe

International Nuclear Information System (INIS)

Cruz N, G.

2015-01-01

This work is focused on studying the sorption capacity of methyl orange dye (Nm) and orange 10 (N-10) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe uncalcined and calcined previously at 500 degrees Celsius. Sorption isotherms were determined and the study of the kinetics of sorption was performed. The materials were characterized before and after sorption processes of these dyes by X-ray diffraction, scanning electron microscopy, the specific surface area determination by the Brunauer-Emmett-Teller method, thermogravimetry coupled to mass and infrared spectrometry. The hydrotalcite type compounds reported in this paper were prepared in the laboratory and their acronyms are: HTMgAlG1, HTMgAlMO, HTMgFeG1 and HTMgFeG2. Note that in this work the best conditions for preparing compounds of Mg/Fe were found. From patterns of X-ray diffraction was identified the typical crystal structure of the hydrotalcite type compounds. By scanning electron microscopy the morphology could be determined in the form of flakes characteristics of these compounds. Likewise with elemental analysis of energy dispersive X-ray spectroscopy the presence of Mg, Al, Fe and C, elements of interest for this study was determined. The compounds presented a specific surface area relatively high from 80 to 120 m 2 /g. Thermogravimetry results presented spectra of mass loss very characteristic associated to water losses, dehydroxylation and decarboxylation. The characteristic bands of water and carbonate were assigned by infrared spectroscopy and the bands corresponding to the dyes sulfonates were identified only for the calcined materials. The sorption capacities found of these compounds were as follows: for Nm in the compound HTMgAlG1 uncalcined was 17.82 mg/g for an initial concentration of 200 mg/L and for calcined (HTMgAlMOcal) of 99.8 mg/g with and initial concentration of 1000 mg/L. Moreover, the sorption capacity of the dye N-10 in this same material was 17.92 mg/g and 99.4 mg

Mechanism of Enhancing Extraction of Vanadium from Stone Coal by Roasting with MgO

Directory of Open Access Journals (Sweden)

Fang Chen

2017-02-01

Full Text Available In this paper, the extraction of vanadium from stone coal by roasting with MgO and leaching with sulfuric acid has been investigated, and the mechanism analysis of stone coal roasting with MgO was studied. The results indicated that under the conditions that the mass fraction of the particles with grain size of 0–0.074 mm in raw ore was 75%, the roasting temperature was 500 °C, the roasting time was 1 h, MgO addition was 3 wt %, the sulfuric acid concentration was 20 vol %, the liquid-to-solid ratio was 1.5 mL/g, the leaching temperature was 95 °C, and leaching time was 2 h, resulting in a vanadium leaching efficiency of 86.63%, which increased by 7.73% compared with that of blank roasting. The mechanism analysis showed that the degree of calcite decomposition was low and, thus, magnesium vanadate was more easily formed than calcium vanadate below 500 °C. Moreover, magnesium vanadate was easier to dissolve than calcium vanadate during the sulfuric acid leaching process. Thus, the vanadium leaching efficiency was enhanced by using MgO as a roasting additive below 500 °C. Additionally, at high temperature the formation of tremolite would consume calcium oxide produced from the decomposition of calcite, thus, the formation of calcium vanadate was hindered, and V2O5 would react with MgO to form magnesium vanadate. Therefore, the vanadium leaching efficiency of roasting with MgO was higher than that of blank roasting at high temperature.

Influence of Nutrient Impregnated into Zeolite Addition on Anaerobic Digestion of Palm Oil Mill Effluent (POME)

Science.gov (United States)

Mellyanawaty, M.; Chusna, F. M. A.; Sudibyo, H.; Nurjanah, N.; Budhijanto, W.

2018-03-01

Palm oil mill effluent (POME) was wastewater generated from palm oil milling activities which was brownish liquid, acidic with pH 3-4, and contained soluble materials which were hazardous to the environment. It was characterized by high organic loading (COD 40,000–60,000 mg/L). According to its characteristics, POME was identified as a potential source to generate renewable energy through anaerobic digestion. In other words, a combination of wastewater treatment and renewable energy production would be an additional advantage to the palm oil industries. Methanogenesis was the rate limiting step in anaerobic digestion. In the conventional anaerobic digester, it required large reactors and long retention time. The addition of microbial immobilization media was to improve anaerobic reactor performance in term of higher organic removal and methane production. Additionally, better performance could lead to reduction of reactor volume and shorter retention time in high rate anaerobic digester. The loading of essential microorganism nutrient into the media might increase the affinity of bacteria to attach and grow on the media surface. Activating or inhibition effects of natural and modified zeolite addition in anaerobic digestion of POME was studied in batch reactors using erlenmeyer of 1,000 mL at COD concentrations of about 8,000 mg/L. Zeolite was impregnated with nickel and magnesium at concentrations of 0.0561 mg Ni/g zeolite and 0.0108 mg Mg/g zeolite. The effect of the different zeolite addition was determined by the measurement of soluble COD (sCOD), Volatile Fatty Acids (VFAs) and biogas production. Greater effect of modified zeolite was observed in zeolite impregnated with nickel with a 54% increase of biogas production. Meanwhile, the modified zeolite impregnated with magnesium had no positive impact to the methanogenic bacteria activities.

In vitro degradation and cytotoxicity of Mg/Ca composites produced by powder metallurgy.

Science.gov (United States)

Zheng, Y F; Gu, X N; Xi, Y L; Chai, D L

2010-05-01

Mg/Ca (1 wt.%, 5 wt.%, 10 wt.% Ca) composites were prepared from pure magnesium and calcium powders using the powder metallurgy method, aiming to enlarge the addition of Ca content without the formation of Mg(2)Ca. The microstructures, mechanical properties and cytotoxicities of Mg/Ca composite samples were investigated. The corrosion of Mg/Ca composites in Dulbecco's modified Eagle's medium (DMEM) for various immersion intervals was studied by electrochemical impedance spectroscopy measurements and environmental scanning electron microscope, with the concentrations of released Mg and Ca ions in DMEM for various immersion time intervals being measured. It was shown that the main constitutional phases were Mg and Ca, which were uniformly distributed in the Mg matrix. The ultimate tensile strength (UTS) and elongation of experimental composites decreased with increasing Ca content, and the UTS of Mg/1Ca composite was comparable with that of as-extruded Mg-1Ca alloy. The corrosion potential increased with increasing Ca content, whereas the current density and the impedance decreased. It was found that the protective surface film formed quickly at the initial immersion stage. With increasing immersion time, the surface film became compact, and the corrosion rate of Mg/Ca composites slowed down. The surface film consisted mainly of CaCO(3), MgCO(3)x3H(2)O, HA and Mg(OH)(2) after 72 h immersion in DMEM. Mg/1Ca and Mg/5Ca composite extracts had no significant toxicity (p>0.05) to L-929 cells, whereas Mg/10Ca composite extract induced approximately 40% reduced cell viability. Copyright (c) 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Development of biodegradable Zn-1X binary alloys with nutrient alloying elements Mg, Ca and Sr

Science.gov (United States)

Li, H. F.; Xie, X. H.; Zheng, Y. F.; Cong, Y.; Zhou, F. Y.; Qiu, K. J.; Wang, X.; Chen, S. H.; Huang, L.; Tian, L.; Qin, L.

2015-01-01

Biodegradable metals have attracted considerable attentions in recent years. Besides the early launched biodegradable Mg and Fe metals, Zn, an essential element with osteogenic potential of human body, is regarded and studied as a new kind of potential biodegradable metal quite recently. Unfortunately, pure Zn is soft, brittle and has low mechanical strength in the practice, which needs further improvement in order to meet the clinical requirements. On the other hand, the widely used industrial Zn-based alloys usually contain biotoxic elements (for instance, ZA series contain toxic Al elements up to 40 wt.%), which subsequently bring up biosafety concerns. In the present work, novel Zn-1X binary alloys, with the addition of nutrition elements Mg, Ca and Sr were designed (cast, rolled and extruded Zn-1Mg, Zn-1Ca and Zn-1Sr). Their microstructure and mechanical property, degradation and in vitro and in vivo biocompatibility were studied systematically. The results demonstrated that the Zn-1X (Mg, Ca and Sr) alloys have profoundly modified the mechanical properties and biocompatibility of pure Zn. Zn-1X (Mg, Ca and Sr) alloys showed great potential for use in a new generation of biodegradable implants, opening up a new avenue in the area of biodegradable metals. PMID:26023878

Development of biodegradable Zn-1X binary alloys with nutrient alloying elements Mg, Ca and Sr.

Science.gov (United States)

Li, H F; Xie, X H; Zheng, Y F; Cong, Y; Zhou, F Y; Qiu, K J; Wang, X; Chen, S H; Huang, L; Tian, L; Qin, L

2015-05-29

Biodegradable metals have attracted considerable attentions in recent years. Besides the early launched biodegradable Mg and Fe metals, Zn, an essential element with osteogenic potential of human body, is regarded and studied as a new kind of potential biodegradable metal quite recently. Unfortunately, pure Zn is soft, brittle and has low mechanical strength in the practice, which needs further improvement in order to meet the clinical requirements. On the other hand, the widely used industrial Zn-based alloys usually contain biotoxic elements (for instance, ZA series contain toxic Al elements up to 40 wt.%), which subsequently bring up biosafety concerns. In the present work, novel Zn-1X binary alloys, with the addition of nutrition elements Mg, Ca and Sr were designed (cast, rolled and extruded Zn-1Mg, Zn-1Ca and Zn-1Sr). Their microstructure and mechanical property, degradation and in vitro and in vivo biocompatibility were studied systematically. The results demonstrated that the Zn-1X (Mg, Ca and Sr) alloys have profoundly modified the mechanical properties and biocompatibility of pure Zn. Zn-1X (Mg, Ca and Sr) alloys showed great potential for use in a new generation of biodegradable implants, opening up a new avenue in the area of biodegradable metals.

Scattering effect of the well-ordered MgB{sub 4} impurity phase in two-step sintered polycrystalline MgB{sub 2} with glycine addition

Energy Technology Data Exchange (ETDEWEB)

Cai, Qi; Liu, Yongchang; Guo, Qianying; Ma, Zongqing [Tianjin University, State Key Lab of Hydraulic Engineering Simulation and Safety, School of Materials Science and Engineering, Tianjin (China)

2017-04-15

Glycine-doped MgB{sub 2} bulk was prepared by two-step sintering in this study, first at 750 C and then 900 C. The MgB{sub 4} particles are induced to precipitate where the dislocations concentrated after C substitution or along the steps of screw dislocation during crystal growth, forming ordered MgB{sub 4} arrays throughout the MgB{sub 2} grain. By means of atomic force microscope, the detected magnetic domains are arranged in agreement with the ordered MgB{sub 4} particles after the measurement of magnetic hysteresis loop, which supported that the nano-scale MgB{sub 4} domain structure brought strong scattering effects and indicated that atomic force microscopy could test the role of the impurities. As a result, the extrapolating upper critical field H{sub c2}(0 K) is enhanced to 22.8 T for the sample with ordered MgB{sub 4}, while only 18.1 T for the un-doped sample underwent the same sintering program. Besides, carbon substitution contributed to the enhancement of H{sub c2} as well. (orig.)

Effect of food additives on hyperphosphatemia among patients with end-stage renal disease: a randomized controlled trial.

Science.gov (United States)

Sullivan, Catherine; Sayre, Srilekha S; Leon, Janeen B; Machekano, Rhoderick; Love, Thomas E; Porter, David; Marbury, Marquisha; Sehgal, Ashwini R

2009-02-11

High dietary phosphorus intake has deleterious consequences for renal patients and is possibly harmful for the general public as well. To prevent hyperphosphatemia, patients with end-stage renal disease limit their intake of foods that are naturally high in phosphorus. However, phosphorus-containing additives are increasingly being added to processed and fast foods. The effect of such additives on serum phosphorus levels is unclear. To determine the effect of limiting the intake of phosphorus-containing food additives on serum phosphorus levels among patients with end-stage renal disease. Cluster randomized controlled trial at 14 long-term hemodialysis facilities in northeast Ohio. Two hundred seventy-nine patients with elevated baseline serum phosphorus levels (>5.5 mg/dL) were recruited between May and October 2007. Two shifts at each of 12 large facilities and 1 shift at each of 2 small facilities were randomly assigned to an intervention or control group. Intervention participants (n=145) received education on avoiding foods with phosphorus additives when purchasing groceries or visiting fast food restaurants. Control participants (n=134) continued to receive usual care. Change in serum phosphorus level after 3 months. At baseline, there was no significant difference in serum phosphorus levels between the 2 groups. After 3 months, the decline in serum phosphorus levels was 0.6 mg/dL larger among intervention vs control participants (95% confidence interval, -1.0 to -0.1 mg/dL). Intervention participants also had statistically significant increases in reading ingredient lists (Pfood knowledge scores (P = .13). Educating end-stage renal disease patients to avoid phosphorus-containing food additives resulted in modest improvements in hyperphosphatemia. clinicaltrials.gov Identifier: NCT00583570.

The effect of the humic acid and herbal additive supplement on production parameters of broiler chicken

Directory of Open Access Journals (Sweden)

Veronika Pistová

2016-10-01

Full Text Available In this study the effect of humic acids and dietary herbal additive (clove (Syzygium aromaticum, lavender (Lavendula angustifolia and black pepper (Piper nigrum L. on production parameters of broiler chicken were studied.  A total of 60 Ross 308 broiler chicken were divided into 3 treatments (n=20. The control group of chickens was fed with complete feed mixtures without any additives. Chicken in treatment T1 were fed a diet containing 1% of humic acid and drank a water containing 150 mg/l of herbal additive. Chicken in treatment T2 were fed with complete feed mixture without any additives and drank a water containing 150 mg/l of herbal additive. The body weight, feed intake and feed conversion were evaluated. The results shout that the body weight was significantly higher (P≤0.05 in treatments groups compared to the control group (the order of the groups: 1796.4±188.1; 2052.9±197.9 and 2140.4±300.4 g±SD. The feed intake was in the control group 3.11 kg, in the treatment T1 3.00 kg and in the treatment T2 3.12 kg. Feed conversion for the entire fattening period was in control group 2.19 kg/kg complete feed mixture, in the treatment T1 1.83 kg/kg complete feed mixture and in the treatment T2 1.84 kg/kg complete feed mixture with no significant different (P≥0.05 compared to control group. In conclusion, supplement by humic acid and herbal additive can improve production parameters of broiler chicken.

KSHV LANA and EBV LMP1 induce the expression of UCH-L1 following viral transformation

Energy Technology Data Exchange (ETDEWEB)

Bentz, Gretchen L.; Bheda-Malge, Anjali; Wang, Ling [Lineberger Comprehensive Cancer Center, University of North Carolina, Chapel Hill (United States); Shackelford, Julia [Lineberger Comprehensive Cancer Center, University of North Carolina, Chapel Hill (United States); Department of Cell and Developmental Biology, University of North Carolina, Chapel Hill (United States); Damania, Blossom [Lineberger Comprehensive Cancer Center, University of North Carolina, Chapel Hill (United States); Departments of Medicine and of Microbiology and Immunology, University of North Carolina, Chapel Hill, NC (United States); Pagano, Joseph S., E-mail: joseph_pagano@med.unc.edu [Lineberger Comprehensive Cancer Center, University of North Carolina, Chapel Hill (United States); Departments of Medicine and of Microbiology and Immunology, University of North Carolina, Chapel Hill, NC (United States)

2014-01-05

Ubiquitin C-terminal Hydrolase L1 (UCH-L1) has oncogenic properties and is highly expressed during malignancies. We recently documented that Epstein-Barr virus (EBV) infection induces uch-l1 expression. Here we show that Kaposi's Sarcoma-associated herpesvirus (KSHV) infection induced UCH-L1 expression, via cooperation of KSHV Latency-Associated Nuclear Antigen (LANA) and RBP-Jκ and activation of the uch-l1 promoter. UCH-L1 expression was also increased in Primary Effusion Lymphoma (PEL) cells co-infected with KSHV and EBV compared with PEL cells infected only with KSHV, suggesting EBV augments the effect of LANA on uch-l1. EBV latent membrane protein 1 (LMP1) is one of the few EBV products expressed in PEL cells. Results showed that LMP1 was sufficient to induce uch-l1 expression, and co-expression of LMP1 and LANA had an additive effect on uch-l1 expression. These results indicate that viral latency products of both human γ-herpesviruses contribute to uch-l1 expression, which may contribute to the progression of lymphoid malignancies. - Highlights: • Infection of endothelial cells with KSHV induced UCH-L1 expression. • KSHV LANA is sufficient for the induction of uch-l1. • Co-infection with KSHV and EBV (observed in some PELs) results in the additive induction of uch-l1. • EBV LMP1 also induced UCH-L1 expression. • LANA- and LMP1-mediated activation of the uch-l1 promoter is in part through RBP-Jκ.

The Effect of Plant Growth Regulators and Different Explants on the Response of Tissue Culture and Cell Suspension Cultures of German Chamomile (Matricaria chamomilla L.

Directory of Open Access Journals (Sweden)

L. Koohi,

2014-07-01

Full Text Available German chamomile (Matricaria chamomilla L. is one of the most important medicinal plants that its essential oils used in different medicinal industries. In this study which was carried out in 2013 growing season at the Faculty of Agricultural Sciences of the University of Mohaghegh Ardabili, the in vitro response of leaf and hypocotyl explants of German Chamomile in B5 medium supplemented with different levels of plant growth regulators including 2,4-D, naphthalene acetic acid (NAA, kinetin and 6-benzylaminopurine (BAP were investigated in a factorial experiment based on completely randomized design (CRD.In addition, cell suspension cultures were established and characterized. Hypocotyl and leaf explants exhibited cell proliferation and produced callus within 1-2 weeks. The highest fresh weight of the callus (264.1 mg was produced by leaf explants in the medium supplemented with 0.5 mg/l 2,4-D and 1 mg/l BAP. However, the leaf explants cultured on medium containing 1.5 mg/l 2,4-D showed the lowest cell proliferation and callus yield (40.42 mg. The highest percentage of root induction from leaf explants (58.73% was observed on the medium containing 4 mg/l 2,4-D and 1 mg/l Kin, and from hypocotyl explants (48.61% was observed on medium supplemented with 1.5 mg/l NAA. The 42.22% of calli derived from hypocotyl explants on B5 medium supplemented with 4 mg/l NAA and 3 mg/l BAP, were friable. Cell suspension cultures of German chamomile were established by transferring of hypocotyl-derived friable calli into the MS medium supplemented with 1.5 mg/l 2,4-D and 1 mg/l kinetin. The growth curve of cell proliferations started 4 days after culture and continued to grow until day 13th, where the cells entered stationary phase.

Structure/property (constitutive and dynamic strength/damage characterization of additively manufactured 316L SS

Directory of Open Access Journals (Sweden)

Gray III G.T.

2015-01-01

Full Text Available For additive manufacturing (AM, the certification and qualification paradigm needs to evolve as there exists no “ASTM-type” additive manufacturing certified process or AM-material produced specifications. Accordingly, utilization of AM materials to meet engineering applications requires quantification of the constitutive properties of these evolving materials in comparison to conventionally-manufactured metals and alloys. Cylinders of 316L SS were produced using a LENS MR-7 laser additive manufacturing system from Optomec (Albuquerque, NM equipped with a 1kW Yb-fiber laser. The microstructure of the AM-316L SS is detailed in both the as-built condition and following heat-treatments designed to obtain full recrystallization. The constitutive behavior as a function of strain rate and temperature is presented and compared to that of nominal annealed wrought 316L SS plate. The dynamic damage evolution and failure response of all three materials was probed using flyer-plate impact driven spallation experiments at a peak stress of 4.5 GPa to examine incipient spallation response. The spall strength of AM-produced 316L SS was found to be very similar for the peak shock stress studied to that of annealed wrought or AM-316L SS following recrystallization. The damage evolution as a function of microstructure was characterized using optical metallography.

Psychiatric comorbidity and additional abuse of drugs in maintenance treatment with L- and D,L-methadone.

Science.gov (United States)

Wedekind, Dirk; Jacobs, Stefan; Karg, Iris; Luedecke, Christel; Schneider, Udo; Cimander, Konrad; Baumann, Pierre; Ruether, Eckart; Poser, Wolfgang; Havemann-Reinecke, Ursula

2010-03-01

Sixty D,L- or L-methadone treated patients in maintenance therapy were interviewed for additional drug abuse and psychiatric comorbidity; 51.7% of the entire population had a comorbid Axis-I disorder, with a higher prevalence in females (P=0.05). Comorbid patients tended to have higher abuse of benzodiazepines, alcohol, cannabis, and cocaine, but not of heroin. They had received a significantly lower D,L- (Pabuse.

Correlative change of corrosion behavior with the microstructure of AZ91 Mg alloy modified with Y additions

International Nuclear Information System (INIS)

Jia, Ruiling; Zhang, Ming; Zhang, Lina; Zhang, Wei; Guo, Feng

2015-01-01

Highlights: • The effect of Y addition into the AZ91 Mg alloys was investigated. • Initial stage of corrosion was studied by in-situ 3D digital microscopy observation. • The potential difference was investigated by Kelvin probe force microscopy. • The effect of Y addition on the corrosion mechanisms of AZ91 alloy was studied. - Abstract: Microstructure characterization of the AZ91 magnesium alloys with or without rare earth element yttrium (Y) has been revealed by SEM, EDS and EPMA. Some Y-rich phases can be found in the magnesium alloys with Y additions. The fraction of β-Mg 17 Al 12 phase obvious decreases and turns into granular distribution with the increase of Y addition instead of original wet distribution along grain boundaries. The results of the potentiodynamic polarization tests show that the corrosion resistance of AZ91 alloy is improved with appropriate Y additions. But an in-situ observation of 3D digital microscopy for the initial stage of corrosion of the magnesium alloy with 0.9%Y addition shows that Y-rich phases act as cathodic effect and the α phases in the vicinity of them acting as anode are corroded. So the additions of Y have a beneficial effect that can depress the overall corrosion of AZ91 alloy, whereas its harmful effect is related to Y-rich phases because they present the highest Volta potential difference from the adjacent matrix and they can drive galvanic corrosion

Correlative change of corrosion behavior with the microstructure of AZ91 Mg alloy modified with Y additions

Energy Technology Data Exchange (ETDEWEB)

Jia, Ruiling, E-mail: jrl014014@163.com [College of Materials Science and Engineering, Inner Mongolia University of Technology, Hohhot, Inner Mongolia 010051 (China); Zhang, Ming; Zhang, Lina [College of Materials Science and Engineering, Inner Mongolia University of Technology, Hohhot, Inner Mongolia 010051 (China); Zhang, Wei [Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, 62 Wencui Road, Shenyang 110016 (China); Guo, Feng [College of Materials Science and Engineering, Inner Mongolia University of Technology, Hohhot, Inner Mongolia 010051 (China)

2015-06-15

Highlights: • The effect of Y addition into the AZ91 Mg alloys was investigated. • Initial stage of corrosion was studied by in-situ 3D digital microscopy observation. • The potential difference was investigated by Kelvin probe force microscopy. • The effect of Y addition on the corrosion mechanisms of AZ91 alloy was studied. - Abstract: Microstructure characterization of the AZ91 magnesium alloys with or without rare earth element yttrium (Y) has been revealed by SEM, EDS and EPMA. Some Y-rich phases can be found in the magnesium alloys with Y additions. The fraction of β-Mg{sub 17}Al{sub 12} phase obvious decreases and turns into granular distribution with the increase of Y addition instead of original wet distribution along grain boundaries. The results of the potentiodynamic polarization tests show that the corrosion resistance of AZ91 alloy is improved with appropriate Y additions. But an in-situ observation of 3D digital microscopy for the initial stage of corrosion of the magnesium alloy with 0.9%Y addition shows that Y-rich phases act as cathodic effect and the α phases in the vicinity of them acting as anode are corroded. So the additions of Y have a beneficial effect that can depress the overall corrosion of AZ91 alloy, whereas its harmful effect is related to Y-rich phases because they present the highest Volta potential difference from the adjacent matrix and they can drive galvanic corrosion.

Effect of samarium (Sm) addition on the microstructures and mechanical properties of Al–7Si–0.7Mg alloys

International Nuclear Information System (INIS)

Qiu, Hongxu; Yan, Hong; Hu, Zhi

2013-01-01

Highlights: •Sm affected the secondary dendrite arm spacing of Al–7Si–0.7Mg alloy. •The coarse plate-like eutectic silicon was fully modified into a fine branched and particle structure when 0.6 wt.% Sm added. •The tensile properties were enhanced by the addition of Sm. •Sm has marked effects on eutectic temperature and the latent heat ΔH R on remelting behavior. •The morphology and chemical composition of Sm-rich intermetallics were studied. -- Abstract: The effects of samarium (Sm) additions (0–0.9 wt.%) on the microstructures and mechanical properties of Al–7Si–0.7Mg alloys have been studied in this article. The microstructures of the as-cast samples were examined by optical microscopy (OM) and scanning electron microscopy (SEM). The experimental results indicated that the rare earth Sm affected the secondary dendrite arm spacing (SDAS) of Al–7Si–0.7Mg alloy. And it was found that Sm had great modification effects on the microstructures of eutectic silicon. When 0.6 wt.% Sm was added to the alloy, the coarse plate-like eutectic silicon was fully modified into a fine fibrous structure; the dendrites of Al–7Si–0.7Mg alloy was best refined. The mechanical properties were investigated by tensile test. The findings indicate that the tensile properties and elongation were improved by the addition of Sm. And a good combination of ultimate tensile strength (215 MPa) and elongation (3.3%) was obtained when the Sm addition was up to 0.6 wt.%. Furthermore the results of thermal analysis reveal that Sm addition had marked effects on eutectic temperature and the latent heat ΔH R on remelting behavior

Clinical Experience With 11,460 mL of a 20-mg/mL, Smooth, Highly Cohesive, Viscous Hyaluronic Acid Filler.

Science.gov (United States)

Humphrey, Shannon; Carruthers, Jean; Carruthers, Alastair

2015-09-01

A 3-dimensional approach to facial rejuvenation restores volume lost over time. Hyaluronic acid (HA) filling agents provide long-lasting correction with minimal side effects and a high level of patient satisfaction. The newest HA formulation is a 20-mg/mL smooth cohesive filler (Juvéderm Voluma [HA-V]) that combines both low- and high-molecular-weight HA for more efficient cross-linking and greater lift capabilities. To document the clinical experience with HA-V over the course of 68 months. The authors conducted a retrospective chart review of patients who received HA-V for facial augmentation between February 1, 2009, and October 1, 2014. Clinical results were assessed 2 weeks after initial treatment, with touch-ups performed as necessary. Color photographs were taken before and after treatment, and adverse events were documented. Over 68 months, the authors treated 2,342 patients with 11,460 mL of HA-V. Aesthetic results lasted upwards of 12 months, and most side effects were transient and mild. Three patients developed signs of vascular compromise that was promptly treated and resolved within 2 months. Twenty-one patients (<0.5%) experienced late-onset, temporary, nontender nodules that were successfully managed with conservative measures. Easy to use and well tolerated, HA-V is ideally formulated for soft-tissue augmentation in the face, with clinical effects lasting 12 months or longer.

Tunable magnetic properties by interfacial manipulation of L1(0)-FePt perpendicular ultrathin film with island-like structures.

Science.gov (United States)

Feng, C; Wang, S G; Yang, M Y; Zhang, E; Zhan, Q; Jiang, Y; Li, B H; Yu, G H

2012-02-01

Based on interfacial manipulation of the MgO single crystal substrate and non-magnetic AIN compound, a L1(0)-FePt perpendicular ultrathin film with the structure of MgO/FePt-AIN/Ta was designed, prepared, and investigated. The film is comprised of L1(0)-FePt "magnetic islands," which exhibits a perpendicular magnetic anisotropy (PMA), tunable coercivity (Hc), and interparticle exchange coupling (IEC). The MgO substrate promotes PMA of the film because of interfacial control of the FePt lattice orientation. The AIN compound is doped to increase the difference of surface energy between FePt layer and MgO substrate and to suppress the growth of FePt grains, which takes control of island growth mode of FePt atoms. The AIN compound also acts as isolator of L1(0)-FePt islands to pin the sites of FePt domains, resulting in the tunability of Hc and IEC of the films.

Pencapaian Fase Embriosomatik Manggis (Garcinia mangostana L. dengan Penambahan Thidiazuron dalam Medium Setengah MS Cair

Directory of Open Access Journals (Sweden)

Innaka Ageng Rineksane

2016-02-01

Full Text Available One of the problems related to the establishment of mangosteen plantation is to obtain seedlings throughout the year, which can be solved by micropropagation.   The propagation of Mangosteen was done through somatic embryogenesis. The objective of this study was to determine the effect of Thidiazuron concentration in ½ MS medium to achieve somatic embryo stages of mangosteen seed. The study consisted of two experiments. Experiment 1: The embryogenic callus c.a.1 g derived from MS solid medium containing of Thidiazuron (0,1; 0,5; dan 1 mg/l and 2,4-Dichlorophenoxy acetic acid (4,6,8 dan 10 mg/l was subcultured into ½ MS0 liquid medium. 2. The embryogenic callus from the previous medium were subcultured into ½ MS liquid medium containing Thidiazuron (0, 1, 2, 4 dan 8 mg/L and Casein hydrolysate 500 mg/L. The results showed that cell suspension were developed after mangosteen embryogenic callus subcultured into ½ MS0 liquid medium.  Somatic embryo stages such as globular, heart and torpedo were formed after the calli derived from the previous ½ MS solid medium containing 10 mg/L 2,4-D and 1 mg/L Thidiazuron were subcultured into ½ MS0 liquid medium in 8 weeks.  Cell suspension in ½ MS liquid medium with or without the addition of  Thidiazuron and Casein hydrolysate has induced the formation of embryo somatic stages such as globular, heart and torpedo after 6 months of incubation.

Synergistic Antihypertensive Effect of Carthamus tinctorius L. Extract and Captopril in l-NAME-Induced Hypertensive Rats via Restoration of eNOS and AT1R Expression

Directory of Open Access Journals (Sweden)

Putcharawipa Maneesai

2016-02-01

Full Text Available This study examined the effect of Carthamus tinctorius (CT extract plus captopril treatment on blood pressure, vascular function, nitric oxide (NO bioavailability, oxidative stress and renin-angiotensin system (RAS in Nω-Nitro-l-arginine methyl ester (l-NAME-induced hypertension. Rats were treated with l-NAME (40 mg/kg/day for five weeks and given CT extract (75 or 150 or 300 or 500 mg/kg/day: captopril (5 mg/kg/day or CT extract (300 mg/kg/day plus captopril (5 mg/kg/day for two consecutive weeks. CT extract reduced blood pressure dose-dependently, and the most effective dose was 300 mg/kg/day. l-NAME-induced hypertensive rats showed abnormalities including high blood pressure, high vascular resistance, impairment of acetylcholine-induced vasorelaxation in isolated aortic rings and mesenteric vascular beds, increased vascular superoxide production and plasma malondialdehyde levels, downregulation of eNOS, low level of plasma nitric oxide metabolites, upregulation of angiotensin II type 1 receptor and increased plasma angiotensin II. These abnormalities were alleviated by treatment with either CT extract or captopril. Combination treatment of CT extract and captopril normalized all the abnormalities found in hypertensive rats except endothelial dysfunction. These data indicate that there are synergistic antihypertensive effects of CT extract and captopril. These effects are likely mediated by their anti-oxidative properties and their inhibition of RAS.

L-Citrulline Supplementation-Increased Skeletal Muscle PGC-1α Expression is Associated With Exercise Performance and Increased Skeletal Muscle Weight.

Science.gov (United States)

Villareal, Myra O; Matsukawa, Toshiya; Isoda, Hiroko

2018-05-24

L-citrulline has recently been reported as a more effective supplement for promoting intracellular NO production compared to L-arginine. Here, the effect of L-citrulline on skeletal muscle and its influence on exercise performance were investigated. The underlying mechanism of its effect, specifically on the expression of skeletal muscle peroxisome proliferator-activated receptor-gamma coactivator-1α (PGC-1α), was also elucidated. Six-week-old ICR mice were orally supplemented with L-citrulline (250 mg kg -1 ) daily, and their performance in weight-loaded swimming exercise every other day for 15 days, was evaluated. In addition, mice muscles were weighed and evaluated for the expression of PGC-1α and PGC-1α-regulated genes. Mice orally supplemented with L-citrulline had significantly higher gastrocnemius and biceps femoris muscle mass. Although not statistically significant, L-citrulline prolonged the swimming time to exhaustion. PGC-1α upregulation was associated with vascular endothelial growth factor α (VEGFα) and insulin-like growth factor 1 (IGF1) upregulation. VEGFα and IGF1 are important for angiogenesis and muscle growth, respectively, and are regulated by PGC-1α. Treatment with L-NAME, a nitric oxide synthesis inhibitor, suppressed the L-citrulline-induced PGC-1α upregulation in-vitro. Supplementation with L-citrulline upregulates skeletal muscle PGC-1α levels resulting to higher skeletal muscle weight that improves time to exhaustion during exercise. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Z-contrast imaging of ordered structures in Pb(Mg1/3Nb2/3)O3 and Ba(Mg1/3Nb2/3)O3

International Nuclear Information System (INIS)

Yan, Y.; Pennycook, S.J.; Xu, Z.; Viehland, D.

1998-02-01

Lead-based cubic perovskites such as Pb(B 1/3 2+ B 2/3 5+ )O 3 (B 2+ Mg, Co, Ni, Zn; B 5+ = Nb, Ta) are relaxor ferroelectrics. Localized order and disorder often occur in materials of this type. In the Pb(Mg 1/3 Nb 2/3 )O 3 (PMN) family, previous studies have proposed two models, space-charge and charge-balance models. In the first model, the ordered regions carry a net negative charge [Pb(Mg 1/2 Nb 1/2 )O 3 ], while in the second model it does not carry a net charge [Pb((Mg 2/3 Nb 1/3 ) 1/2 Nb 1/2 )O 3 ]. However, no direct evidence for these two models has appeared in the literature yet. In this paper the authors report the first direct observations of local ordering in undoped and La-doped Pb(Mg 1/3 Nb 2/3 )O 3 , using high-resolution Z-contrast imaging. Because the ordered structure in Ba(Mg 1/3 Nb 2/3 )O 3 is well known, the Z-contrast image from an ordered domain is used as a reference for this study

Carnation (Dianthus caryophylus L.).

Science.gov (United States)

Nontaswatsri, Chalermsri; Fukai, Seiichi

2006-01-01

Carnation is a valuable crop for the cut flower industry and demand for new and improved varieties is growing. However, genetic transformation of carnations is currently limited because of a lack of efficient routine technique. In this chapter, we present an easy and effective protocol for gene transfer to carnation node explants and subsequent adventitious shoot regeneration. For high-adventitious shoot regeneration, node explants from first to third node of 5- to 8-cm long shoots were cultured on Murashige and Skoog (MS) medium, containing 1.0 mg/Lthidiazuron (TDZ), 0.1 mg/L alpha-napthalenoacetic acid (NAA), 20 g/L sucrose, and 2 g/L Gellan gum for 10 d. Then the explants were cut into 8 radial segments and subcultured onto MS medium, containing 1.0 mg/L BA, 0.1 mg/L NAA, 20 g/L sucrose and 2 g/L Gellan Gum. For effective genetic transformation, 3- to 5-d precultured node explants were submerged in an Agrobacerium suspension for 10 min, then cocultivated on filter paper soaked with water and 50 microM acetosyringone (AS). After cocultivation, the explants were cut into eight radial segments and subcultured onto selection medium until transformed shoots regenerated from the explants.

Insights into chirality distributions of single-walled carbon nanotubes grown on different CoxMg1-xO solid solutions

DEFF Research Database (Denmark)

He, Maoshuai; Jiang, Hua; Kauppi, Inkeri

2014-01-01

Low-temperature chemical vapor deposition (CVD) growth of single-walled carbon nanotubes (SWNTs) was achieved on two different types of Co xMg1-xO catalysts prepared by different techniques: atomic layer deposition (ALD) and impregnation. The chirality distribution of SWNTs grown on the ALD......-prepared CoxMg1-xO catalyst is wider than that of SWNTs grown on the impregnation-prepared CoxMg 1-xO catalyst. The different chirality distributions of SWNTs are related to their different growth modes. The ALD-prepared CoxMg 1-xO catalyzes the growth of SWNTs by "tip growth" mode, as revealed by in situ...... for the synthesis of SWNTs with high chiral-selectivity. In addition, impregnation-prepared Co xMg1-xO catalysts calcinated at different temperatures were systematically studied and their catalytic performances in synthesizing carbon nanotubes were elucidated. This work illustrates the influence of metal...

Mass propagation of Rauwolfia serpentina L. Benth.

Science.gov (United States)

Salma, U; Rahman, M S M; Islam, S; Haque, N; Khatun, M; Jubair, T A; Paul, B C

2008-05-01

A protocol for mass propagation through axillary bud proliferation was established for Rauwolfia serpentina L. Benth. (Apocynaceae). MS medium supplemented with 1.5 mg L(-1) BA and 0.2 mg L(-1) NAA elicited the maximum number of shoots (4 multiple shoots) from nodal explants. These adventitious shoots were best rooted on half strength MS medium supplemented with 1.0 mg L(-1) each of IBA and IAA. The in vitro raised plants were acclimatized in glass house and successfully transplanted to field condition with almost 95% survival.

Vibrational spectra of 1-hydroxy- and 1,4-dihydroxyanthraquinones and their magnesium chelate complexes. I. Isotopic effects of OH/OD and 24Mg/26Mg substitutions

International Nuclear Information System (INIS)

Kirszenbaum, Marek

1977-01-01

The vibrational spectra of 1-hydroxy- and 1,4-dihydroxyanthraquinones, their deuterated derivatives and their 24 Mg/ 26 Mg chelate complexes are examined in the spectral region 1700-250cm -1 . The study of deuteroxyanthraquinones allow an assignment of the OH/OD group vibrations and show the multiple coupling of the delta OH vibrations with the vCC and delta CH quinonic vibrations. These results lead to a modification of some spectral assignments of magnesium chelate complexe of 1-OH-AQ. The isotopic 24 Mg/ 26 Mg substitution enables the chelate ring vibrations which depend on the motions of the magnesium atom to be observed. The vC=O and vC-O vibrations frequencies of magnesium chelate complexe [Mg(1,4-O 2 -AQ)]sub(n) show an important difference of the chelate ring electronic state in comparison of those of 1,4-(OH) 2 -AQ. The discussion of the infrared and Raman spectra in the Mg-O vibrations region lead to the conclusion that the configuration of oxygens arround the magnesium is tetrahedral [fr

Effect of Aluminum Addition on the Evolution of Microstructure, Crystallographic Texture and Mechanical Properties of Single Phase Hexagonal Close Packed Mg-Li Alloys

Science.gov (United States)

Bhagat Singh, P.; Sabat, R. K.; Kumaran, S.; Suwas, S.

2018-02-01

In the present investigation, an effort has been made to understand the effect of aluminum addition to α Mg-Li alloys. The corresponding composition Mg-4Li- xAl ( x = 0, 2, 4 and 6 wt.%) alloys have been prepared by stir casting route under an argon environment. Extrusion was carried out at 300 °C with the extrusion ratio of 15:1. Significant grain refinement was observed after extrusion. X-ray diffraction-based investigation of the cast and extruded alloys showed the presence of intermetallic compounds such as Mg17Al12 and AlLi in the Al-rich alloys namely, Mg-4Li- xAl ( x = 4 and 6 wt.%). These precipitates were also present in the extruded plus annealed samples, indicating the stability of the precipitates at high temperature. The bulk x-ray texture measurement revealed a crystallographic texture where the c-axis of the h.c.p crystals was perpendicular to the extrusion direction (ED) for extruded sample. A texture transition was observed on annealing. The c-axis was oriented parallel to the ED. Mechanical properties of the cast, extruded and extruded plus annealed material illustrate that the addition of Al led to enhancement in hardness, yield strength and ultimate tensile strength.

Analysis of Ca and Mg in blood of golden hamster using NAA technique

International Nuclear Information System (INIS)

Aguiar, Rodrigo O.; Zamboni, Cibele B.; Medeiros, Jose A.G.

2009-01-01

Neutron activation analysis (NAA) technique has been used to determine simultaneously Ca and Mg concentrations in whole blood of Golden Hamster. The reference values for Ca (0.17 - 0.29 gL -1 ) and Mg (0.042 - 0.074 gL -1 ) can be used to performed biochemistry investigation using whole blood. (author)

Malignant mesothelioma effusions are infiltrated by CD3+ T cells highly expressing PD-L1 and the PD-L1+ tumor cells within these effusions are susceptible to ADCC by the anti-PD-L1 antibody avelumab

Science.gov (United States)

Khanna, Swati; Thomas, Anish; Abate-Daga, Daniel; Zhang, Jingli; Morrow, Betsy; Steinberg, Seth M.; Orlandi, Augusto; Ferroni, Patrizia; Schlom, Jeffrey; Guadagni, Fiorella; Hassan, Raffit

2016-01-01

INTRODUCTION The functional aspects of programmed death 1 (PD-1) and PD ligand 1 (PD-L1) immune checkpoints in malignant mesothelioma have not been studied. METHODS Tumor samples from 65 patients with mesothelioma were evaluated for PD-L1 expression by immunohistochemistry and its prognostic significance. Malignant effusions from patients with pleural and peritoneal mesothelioma were evaluated for PD-1+ and PD-L1+ infiltrating lymphocytes and their role in inducing tumor cell PD-L1 expression. Antibody dependent cellular cytotoxicity (ADCC) of avelumab, a fully humanized IgG1 anti PD-L1 antibody towards primary mesothelioma cell lines was evaluated in presence of autologous and allogeneic NK cells. RESULTS Of 65 pleural and peritoneal mesothelioma tumors examined, 41 (63%) were PD-L1 positive, which was associated with slightly inferior overall survival compared to patients with PD-L1 negative tumors (median 23.0 vs. 33.3 months; p=0.35). The frequency of PD-L1 expression was similar in pleural and peritoneal mesothelioma patients with 62% and 64% of samples positive, respectively. Of nine mesothelioma effusion samples evaluated, the fraction of cells expressing PD-L1 ranged from 12 to 83%. Of 7 patients with paired malignant effusion and peripheral blood mononuclear cells (PBMC) samples, PD-L1 expression was significantly higher on CD3+ T cells present in malignant effusions as compared with PBMC (p=0.016). In addition, CD14+PD-1+ cells were elevated in malignant effusions compared with PBMC (p=0.031). The lymphocytes present in malignant effusions recognized autologous tumor cells and induced IFN-γ-mediated PD-L1 expression on the tumor cell surface. Of the three primary mesothelioma cell lines tested, two were susceptible to avelumab mediated ADCC in presence of autologous NK cells. CONCLUSION The majority of pleural as well as peritoneal mesothelioma express PD-L1. Malignant effusions in this disease are characterized by presence of tumor cells and CD3+ T

Synthesis of MgO nanoparticle loaded mesoporous Al2O3 and its defluoridation study

International Nuclear Information System (INIS)

Dayananda, Desagani; Sarva, Venkateswara R.; Prasad, Sivankutty V.; Arunachalam, Jayaraman; Parameswaran, Padmanabhan; Ghosh, Narendra N.

2015-01-01

Highlights: • Simple and cost effective preparation of MgO nanoparticles loaded mesoporous Al 2 O 3 . • Adsorbents possess high surface area and mesoporous structure. • Higher fluoride removal capacity of MgO loaded Al 2 O 3 than that of pure Al 2 O 3 . • Faster fluoride adsorption kinetics of MgO loaded Al 2 O 3 from water. - Abstract: MgO nanoparticle loaded mesoporous alumina has been synthesized using a simple aqueous solution based cost effective method for removal of fluoride from water. Wide angle powder X-ray diffraction, nitrogen adsorption desorption analysis, transmission electron microscopy techniques and energy dispersive X-ray spectroscopy were used to characterize the synthesized adsorbents. Synthesized adsorbents possess high surface area with mesoporous structure. The adsorbents have been thoroughly investigated for the adsorption of F − using batch adsorption method. MgO nanoparticle loading on mesoporous Al 2 O 3 enhances the F − adsorption capacity of Al 2 O 3 from 56% to 90% (initial F − concentration = 10 mg L −1 ). Kinetic study revealed that adsorption kinetics follows the pseudo-second order model, suggesting the chemisorption mechanism. The F − adsorption isotherm data was explained by both Langmuir and Freundlich model. The maximum adsorption capacity of 40MgO@Al 2 O 3 was 37.35 mg g −1 . It was also observed that, when the solutions having F − concentration of 5 mg L −1 and 10 mg L −1 was treated with 40MgO@Al 2 O 3 , the F − concentration in treated water became <1 mg L −1 , which is well below the recommendation of WHO

Impact of trace element additives on anaerobic digestion of sewage sludge with in-situ carbon dioxide sequestration

Energy Technology Data Exchange (ETDEWEB)

Linville, Jessica L.; Shen, Yanwen; Schoene, Robin P.; Nguyen, Maximilian; Urgun-Demirtas, Meltem; Snyder, Seth W.

2016-09-01

Anaerobic digestion (AD) of sludge at wastewater treatment plants can benefit from addition of essential trace metals such as iron, nickel and cobalt to increase biogas production for utilization in combined heat and power systems, fed into natural gas pipelines or as a vehicle fuel. This study evaluated the impact and benefits of Ni/Co and olivine addition to the digester at mesophilic temperatures. These additions supplement previously reported research in which iron-rich olivine (MgSiO4) was added to sequester CO2 in-situ during batch AD of sludge. Trace element addition has been shown to stimulate and stabilize biogas production and have a synergistic effect on the mineral carbonation process. AD with 5% w/v olivine and 1.5 mg/L Ni/Co addition had a 17.3% increase in methane volume, a 6% increase in initial exponential methane production rate and a 56% increase in methane yield (mL CH4/g CODdegraded) compared to the control due to synergistic trace element and olivine addition while maintaining 17.7% CO2 sequestration from olivine addition. Both first-order kinetic modeling and response surface methodology modeling confirmed the combined benefit of the trace elements and olivine addition. These results were significantly higher than previously reported results with olivine addition alone [1].

Superplasticity behaviors of Al-Zn-Mg-Zr cold-rolled alloy sheet with minor Sc addition

Energy Technology Data Exchange (ETDEWEB)

Xiang, H. [School of Materials Science and Engineering, Central South University (Light Alloy Research Institute, Central South University), Changsha 410083 (China); Nonferrous Metal Oriented Advanced Structural Materials and Manufacturing Cooperative Innovation Center, Changsha 410083 (China); Pan, Q.L., E-mail: pql2016@126.com [School of Materials Science and Engineering, Central South University (Light Alloy Research Institute, Central South University), Changsha 410083 (China); Nonferrous Metal Oriented Advanced Structural Materials and Manufacturing Cooperative Innovation Center, Changsha 410083 (China); Yu, X.H.; Huang, X.; Sun, X.; Wang, X.D.; Li, M.J.; Yin, Z.M. [School of Materials Science and Engineering, Central South University (Light Alloy Research Institute, Central South University), Changsha 410083 (China); Nonferrous Metal Oriented Advanced Structural Materials and Manufacturing Cooperative Innovation Center, Changsha 410083 (China)

2016-10-31

A refined microstructure of Al-Zn-Mg-Sc-Zr alloy sheet was produced by simple hot and cold rolling to an average grain size of 3 µm. Experiments were completed in electro-fluid servo-fatigue tester and results were investigated by means of optical microscope (OM), scanning electron microscopy (SEM) and transmission electron microscope (TEM). Superplastic deformation was conducted and superplastic ductility of ≥200% was achieved at a testing temperature range from 425 ºC to 500 ºC and relative high strain rate range of 1×10{sup −3} s{sup −1}~1×10{sup −1} s{sup −1}. The maximum elongation of 539% was obtained at 500 ºC and 1×10{sup −2} s{sup −1}. In addition, the scanning electron microscopy (SEM) and transmission electron microscope (TEM) analyses showed that the presence of Al{sub 3} (Sc, Zr) particles in pinning grain boundaries and dislocations had a great influence on the superplastic deformation. The analyses of superplastic test data calculated out the coherent strain rates sensitivity parameter of 0.43 and the average activation energy of 143.762 kJ/mol. The data interpreted that the dominant deformation mechanism was grain boundary sliding controlled by lattice self-diffusion.

Formation of aluminum titanate with small additions of MgO and SiO2

International Nuclear Information System (INIS)

Guedes-Silva, Cecilia Chaves; Ferreira, Thiago dos Santos; Genova, Luis Antonio; Carvalho, Flavio Machado de Souza

2016-01-01

The formation of aluminum titanate was investigated by isothermal treatments of samples obtained from equimolar mixtures of alumina and titania, containing small amounts of silica and magnesia. Results of differential thermal analysis and Rietveld refinements of data collected by X-ray powder diffraction (XRPD) showed that additions of silica in amounts used in this work did not influence the formation of aluminum titanate. However, the presence of magnesia favored the formation of aluminum titanate in two steps, first one by incorporating Mg 2+ into Al 2 TiO 5 lattice during its initial formation, and the second one by accelerating the Al 2 TiO 5 formation, contributing to large quantities of this phase. MgO doped samples have also developed a more suitable microstructure for stabilizing of Al 2 TiO 5 , what make them promising for applications such as thermal barriers, internal combustion engines and support material for catalyst. (author)

Role of dopants in LiF:Mg,Cu, LiF:Mg,P and LiF:Mg,Cu,P detectors

International Nuclear Information System (INIS)

Mohammadi, Kh.; Moussavi Zarandi, A.; Afarideh, H.; Shahmaleki, S.

2013-01-01

In this study, electronic structure of LiF crystal doped with Mg,Cu,P impurities was studied with WIEN2k code on the basis of FPLAPW+lo method. Results show that in Mg-doped LiF composition, an electronic trap was created with impurity concentration of 1.56% and 3.125%. In this condition, the electronic trap with increasing the percentage of the impurities up to 4.687% is annihilated. It was found, that by doping of Mg and Cu or P simultaneously, a hole-trap is created in valence band. It was realized that in LiF:Mg,Cu, LiF:Mg,P and LiF:Mg,Cu,P, Cu impurity and Li atom, have a key role in creation of levels which lead to create electronic and hole traps. Mg impurity and F atom, only have a role in creation of electronic traps. In addition, P impurity has a main role in creation of the electronic and hole traps in LiF:Mg,Cu,P. The activation energy of electronic and hole trap in LiF:Mg,Cu, LiF:Mg,P and LiF:Mg,Cu,P crystalline lattice were obtained as 0.3 and 5.5 eV, 0.92 and 3.4 eV and 0.75 and 3.1 eV, respectively. - Graphical abstract: Figure (a) and (b) shows changes in electronic structure and band gap energy of LiF crystal due to presence of Mg and Cu, Mg and P ions respectively. - Highlights: • Electronic structure of LiF, LiF:Mg,Cu, LiF:Mg,P and LiF:Mg,Cu,P materials were studied with WIEN2K code. • In LiF:Mg,Cu and LiF:Mg,Cu,P, Li atom and Cu impurity have a key role in creation of levels. • F atom and Mg impurity only have a role in creation of electronic traps. • In LiF:Mg,Cu,P, P impurity has a main role in creation of electronic and hole traps

Effect of Sn addition on the microstructure and deformation behavior of Mg-3Al alloy

International Nuclear Information System (INIS)

Suh, Byeong-Chan; Kim, Jae H.; Bae, Jun Ho; Hwang, Ji Hyun; Shim, Myeong-Shik; Kim, Nack J.

2017-01-01

Mg alloys generally suffer from their poor formability at low temperatures due to their strong basal texture and a lack of adequate deformation systems. In the present study, a small amount of Sn was added instead of Zn to Mg-3Al alloy to modify its deformation behavior and improve the stretch formability. Microstructural examinations of the deformed Mg-3Al-1Sn (AT31) alloy by electron backscatter diffraction and transmission electron microscopy show that prismatic slip is quite active during deformation, resulting in much lower r-values and planar anisotropy than the counterpart Mg-3Al-1Zn (AZ31) alloy. Polycrystal plasticity simulation based on visco-plasticity self-consistent (VPSC) model also shows that prismatic slip is the dominant deformation mode in AT31 alloy besides basal slip. As a consequence, AT31 alloy shows a much higher stretch formability than AZ31 alloy. On the other hand, AZ31 alloy shows the development of intense shear bands during stretch forming, and these shear bands act as crack propagating paths, limiting the stretch formability of AZ31 alloy.

A successional stage community dominated by Pteridium aquilinum (L.) Kuhn. in Lavras County, MG, Brazil

OpenAIRE

Martins, G. de; Carvalho, D.A. de

1982-01-01

Numa área situada no município de Lavras, MG, o desmatamento realizado há cerca de dez anos propiciou a formação de uma comunidade infestante dominada por Pteridium aquilium (L.) Khun., te ndo como codominantes Imperara brasiliensis Trin. e Andropogon bicornis L.. Como fatores que mantém esta comu nidade devem ser considerados: a) as queimadas intermiten te s; b) a acidez do solo; c) a alta percentagem de saturação de aluminio ; d) a ação fitotóxica do próprio P. aquilinum; e) a falta de pala...

Analysis of Ca and Mg in blood of golden hamster using NAA technique

Energy Technology Data Exchange (ETDEWEB)

Aguiar, Rodrigo O.; Zamboni, Cibele B.; Medeiros, Jose A.G. [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN/SP), Sao Paulo, SP (Brazil)], e-mail: rodrigoaguiar@usp.br, e-mail: czamboni@ipen.br, e-mail: jageiros@yahoo.com.br

2009-07-01

Neutron activation analysis (NAA) technique has been used to determine simultaneously Ca and Mg concentrations in whole blood of Golden Hamster. The reference values for Ca (0.17 - 0.29 gL{sup -1} ) and Mg (0.042 - 0.074 gL{sup -1} ) can be used to performed biochemistry investigation using whole blood. (author)

Significance of tear β2-MG radioimmunoassay in herpes simplex keratitis

International Nuclear Information System (INIS)

Feng Zhuxu; Zhao Suzhen; Zhang Qiliang; Chen Fengfen; Tang Baoyi

1994-01-01

Levels of tear and serum β 2 -MG are determined with radioimmunoassay in 35 patients with herpes simplex keratitis and 40 normal subjects. The results show that tear β 2 -MG levels of patients with herpes simplex keratitis (13.21 +- 6.15 mg/l) and normal subjects (8.43 +- 1.52 mg/l) are significantly different (P 2 -MG levels of tear and that of serum in normal subjects (P 2 -MG levels of tear and that of serum in patients with herpes simplex keratitis (P 2 -MG levels of patients with herpes simplex keratitis and that of normal subjects (P>0.05). The β 2 -MG levels of tear is higher than that of serum in normal subjects which reflects more correctly immune condition of patients with herpes simplex keratitis than that of serum

Benefits of carbon addition on the hydrogen absorption properties of Mg-based thin films grown by Pulsed Laser Deposition

International Nuclear Information System (INIS)

Darok, X.; Rougier, A.; Bhat, V.; Aymard, L.; Dupont, L.; Laffont, L.; Tarascon, J.-M.

2006-01-01

Mg-Ni thin films were grown using Pulsed Laser Deposition. In situ optical changes from shiny metallic to transparent states were observed for films deposited in vacuum and under an Ar/H 2 gas mixture (93/7%), respectively. Optical changes were also achieved by ex situ hydrogenation under hydrogen gas pressure of 15 bars at 200 deg. C. However, after ex situ hydrogenation, the optical transmittance of the Mg-based hydrogenated thin films did not exceed 25%. Such limitation was attributed to oxygen contamination, as deduced by High Resolution Transmission Electron Microscopy observations, showing the co-existence of both Mg-based and MgO phases for as-deposited films. A significant decrease in oxygen contamination was successfully achieved with the addition of carbon, leading to the preparation of (Mg-based)-C x (x < 20%) thin films showing a faster and easier hydrogenation

Influence of soil properties and phosphate addition on arsenic uptake from polluted soils by velvetgrass (Holcus lanatus).

Science.gov (United States)

Lewińska, K; Karczewska, A

2013-01-01

Four kinds of soil material were used in a pot experiment with velvetgrass (Holcus lanatus). Two unpolluted soils: sand (S) and loam (L) were spiked with sodium arsenite (As II) and arsenate (As V), to obtain total arsenic (As) concentrations of 500 mg As kg(-1). Two other soils (ZS I, ZS III), containing 3320 and 5350 mg As kg(-1), were collected from Zloty Stok where gold and arsenic ores were mined and processed for several centuries. The effects of phosphate addition on plants growth and As uptake were investigated. Phosphate was applied to soils in the form of NH4H2PO4 at the rate 0.2 g P/kg. Average concentrations of arsenic in the shoots of velvetgrass grown in spiked soils S and L without P amendment were in the range 18-210 mg As kg(-1) d.wt., whereas those in plants grown on ZS I and ZS II soils were considerably lower, and varied in the range 11-52 mg As kg(-1) d.wt. The addition of phosphate caused a significant increase in plant biomass and therefore the total amounts of As taken up by plants, however, the differences in As concentrations in the shoots of velvetgrass amended and non-amended with phosphate were not statistically significant.

Al2O3 base composites, with addition of NbC and MgO

International Nuclear Information System (INIS)

Tonello, Karolina Pereira dos Santos

2009-01-01

The worldwide technological advances generate the needs of improved materials with better properties, according to its final purpose. Alumina composites with the addition of carbide particles have become an interesting option for structural applications. This work studies the influence of two commercial aluminas with different particle size and the adding of 1.5 and 6% in volume of niobium carbide and MgO 500 ppm in microstructural and mechanical properties of the composite. Samples were prepared by uniaxial and isostatic pressing and sintering was carried out in a graphite resistance furnace at 1600, 1650, 1700 and 1750 degree C for thirty minutes in Ar atmosphere. The obtained samples were evaluated sintering behavior, density, microstructure and mechanical properties, diffusion tests were realized to verify chemical reactivity between pairs formed by alumina and gray cast iron samples. The differences between aluminas caused some changes on the composites final properties. The composites produced with A16 alumina presented density about 2% higher than those produced with A1000 alumina. Similarly, the hardness also showed higher values. The carbide niobium added to the matrix of alumina delayed the sintering start, with an increase of about 30% in shrinkage initial states, when 6% of NbC was added. Composite with addition of 1,5% of NbC have higher density and hardness, even at lower sintering temperatures. The adding of niobium carbide to the alumina matrix and higher sintering temperatures provided higher density, hardness and fracture toughness to the composite. The best densification and hardness results of were obtained for composites produced with alumina A16 and when 1.5% of NbC was added. (author)

Multiplicação in vitro de oliveira (Olea europaea L. Olive (Olea europaea L. in vitro multiplication

Directory of Open Access Journals (Sweden)

Leonardo Ferreira Dutra

2004-02-01

Full Text Available Com o objetivo de induzir a multiplicação em explantes de oliveira, segmentos nodais oriundos de plântulas mantidas in vitro foram excisados e inoculados em tubos de ensaio contendo meio de cultura MS suplementado com 2 g L-1 de carvão ativado, BAP (0, 1, 2 e 4 mg L-1 e ANA (0; 0,01; 0,1 e 1 mg L-1, solidificado com 6 g L-1 de ágar e pH ajustado para 5,8. Durante 100 dias, os explantes foram mantidos em sala de crescimento a 25±1ºC, intensidade luminosa de 32 µmoles.m-2.s-1 e fotoperíodo de 16 horas. Não houve indução de brotações nos segmentos nodais. O maior comprimento da parte aérea foi obtido com 0,1 mg L-1 de ANA na ausência de BAP. O meio de cultura sem BAP proporcionou maior peso de matéria fresca da parte aérea.This work had the objective to induce olive multiplication. Nodal segments from in vitro plantlets were excised and inoculated in test tubes containing MS culture medium supplemented with activated charcoal (2 g L-1, BAP (0, 1, 2 and 4 mg L-1, NAA (0; 0.01; 0.1 and 1 mg L-1, agar (6 g L-1 and pH adjusted to 5.8. The explant were maintained in growth room to 25±1°C, 32 µmoles.m-2.s-1 light intensity and 16 hours photoperiod for 100 days. There was not shoots induction in the nodal segments. Larger length of aerial part were obtained with ANA 0.1 mg L-1 in the BAP absence. Culture medium without BAP provides larger weight of fresh matter of the aerial part.

Comparison of 1 mg and 2 mg overnight dexamethasone suppression tests for the screening of Cushing's syndrome in obese patients.

Science.gov (United States)

Sahin, Mustafa; Kebapcilar, Levent; Taslipinar, Abdullah; Azal, Omer; Ozgurtas, Taner; Corakci, Ahmet; Akgul, Emin Ozgur; Taslipinar, Mine Yavuz; Yazici, Mahmut; Kutlu, Mustafa

2009-01-01

Obesity is currently a major public health problem and one of the potential underlying causes of obesity in a minority of patients is Cushing's syndrome (CS). Traditionally, the gold standard screening test for CS is 1 mg dexamethasone overnight suppression test. However, it is known that obese subjects have high false positive results with this test. We have therefore compared the 1 mg and 2 mg overnight dexamethasone suppression tests in obese subjects. Patients whose serum cortisol after ODST was >50 nM underwent and a low-dose dexamethasone suppression test (LDDST); 24-hour urine cortisol was collected for basal urinary free cortisol (UFC). For positive results after overnight 1-mg dexamethasone suppression test we also performed the overnight 2-mg dexamethasone suppression test. We prospectively evaluated 100 patients (22 men and 78 women, ranging in age from 17 to 73 years with a body mass index (BMI) >30 kg/m2 who had been referred to our hospital-affiliated endocrine clinic because of simple obesity. Suppression of serum cortisol to suppression. Thyroid function tests, lipid profiles, homocysteine, antithyroglobulin, anti-thyroid peroxidase antibody levels, vitamin B12, folate levels, insulin resistance [by homeostasis model assessment (HOMA)] and 1.0 mg postdexamethasone (postdex) suppression cortisol levels were measured. We found an 8% false-positive rate in 1 mg overnight test and 2% in 2 mg overnight test (p=0.001). There was no correlation between the cortisol levels after ODST and other parameters. Our results indicate that the 2 mg overnight dexamethasone suppression test (ODST) is more convenient and accurate than 1-mg ODST as a screening test for excluding CS in subjects with simple obesity.

Enhancement of Mechanical Properties of Extruded Mg-9Al-1Zn-1MM-0.7CaO-0.3Mn Alloy Through Pre-aging Treatment

Science.gov (United States)

Jeong, Seok Hoan; Kim, Yong Joo; Kong, Kyung Ho; Cho, Tae Hee; Kim, Young Kyun; Lim, Hyun Kyu; Kim, Won Tae; Kim, Do Hyang

2018-03-01

The effect of pre-aging treatment before extrusion has been investigated in Mg-9.0Al-1.0Zn-1MM-0.7CaO-0.3Mn alloy. The as-cast microstructure consists of α-Mg dendrite with secondary solidification phase particles, (Mg, Al)2Ca, β-Mg17Al12 and Al11RE3 at the inter-dendritic region. After extrusion, β-Mg17Al12 precipitates are present, but higher density and more homogeneous distribution in pre-aged alloy. In addition, μm-scale banded bulk β-Mg17Al12 particles are generated during extrusion. Al11RE3 particles are broken into small particles, and are aligned along the extrusion direction. (Mg, Al)2Ca particles are only slightly elongated along the extrusion direction, providing stronger particle stimulated nucleation (PSN) effect by severe deformation during extrusion. The mechanical properties can be significantly enhanced by introducing pre-aging treatment, i.e. β-Mg17Al12 precipitates provide grain refining and strengthening effects and (Mg, Al)2Ca particles provide PSN effect.

Perbandingan Penambahan PePerbandingan Penambahan Petidin 0,25 mg/kgBB dengan Klonidin 1 µg/kgBB pada Bupivakain 0,25% untuk Blok Infraorbital pada Labioplasti Anak terhadap Lama Analgesia Pascaoperasi

Directory of Open Access Journals (Sweden)

Dewi Ramadani

2014-08-01

Full Text Available Post operative pain for labioplasty can be prevented by bilateral infraorbital block. This study aimed to compare the effectiveness addition of pethidine 0.25 mg/kgBW and clonidine 1 µg/kgBW to bupivacaine 0.25% for postoperative analgesia using infraorbital block in paediatric labioplasty with a pain scale score face, leg, activity, cry, consolability (FLACC. The study was a single-blind randomized controlled trial from March to September 2013 involving 30 pediatric patients, physical status American Society of Anesthesiologist (ASA II, ages 3 months–1 year for labioplasty surgery with bilateral infraorbital block at Dr. Hasan Sadikin Hospital Bandung. Subjects were grouped into two groups: 15 subjects using adjuvant pethidine 0.25 mg/kgBW (BP and 15 subjects using adjuvant clonidine 1 ug/kgBW (BK. After induction of anesthesia, infraorbital block done 1 mL on each side of the face. Data were analyzed by t test, showed a highly significant difference (p<0.01 in BP group compared with BK, the average length of postoperative analgesia 1.828 minutes (30 hours vs 1072 minutes (18 hours. The conclusions is the addition of pethidine 0.25 mg/kgBW in bupivacaine 0.25% to infraorbital block in paediatric labioplasty provide postoperative analgesia longer than of clonidine 1 µg/kgBW.

Mg/Ca of Continental Ostracode Shells

Science.gov (United States)

Ito, E.; Forester, R. M.; Marco-Barba, J.; Mezquita, F.

2007-12-01

Marine ionic chemistry is thought to remain constant. This, together with the belief that marine calcifiers partition Mg/Ca in a systematic manner as functions of temperature (and Mg/Ca) of water forms the basis of the Mg/Ca thermometer. In continental settings both of these assumptions are usually not true. Continental waters contain a wide variety of solutes in absolute and relative ion concentrations. Hence, waters with identical Mg/Ca may have very different concentrations of Mg and Ca and very different anions. Here we use two examples to focus on the effects of ion chemistry on Mg/Ca partitioning in continental ostracode shells and we ignore the complexities of solute evolution, which can change Mg/Ca over timescales of minutes to millennia. Palacios-Fest and Dettman (2001) conducted a monthly study of ,Cypridopsis vidua at El Yeso Lake in Sonora, Mexico. They established a relation between temperature and average shell Mg/Ca using regression analyses on averaged data. When their Mg/Ca-temperature relation is applied to monthly ,C. vidua data from Page Pond near Cleveland, Ohio, water temperatures of -8 to -1°C are obtained. The observed Mg/Ca ranges for El Yeso Lake (0.31 to 0.46) and Page Pond (0.33 to 0.46) are similar, as are their specific conductivities (700 to 850μS for El Yeso Lake; 400 to 600μS for Page Pond). However, [Ca] is 140-260 mg/L for El Yeso, but only 70-90 mg/L for Page Pond. Page Pond data, in fact, shows a good temperature shell Mg/Ca relation for .C. vidua, but the relation is different from that at El Yeso. Hence, shell Mg/Ca is a multi-valued, family of curves function of temperature and Mg/Ca of water that depends on the [Mg] and [Ca] values in water and perhaps other factors. Our second example comes from sites near Valencia, Spain and involves shell data for ,Cyprideis torosa, an estuarine ostracode that is tolerant of a wide range of salinity and can live in continental waters as long as the carbonate alkalinity to Ca ratio is

Quasicrystal-reinforced Mg alloys.

Science.gov (United States)

Kyun Kim, Young; Tae Kim, Won; Hyang Kim, Do

2014-04-01

The formation of the icosahedral phase (I-phase) as a secondary solidification phase in Mg-Zn-Y and Mg-Zn-Al base systems provides useful advantages in designing high performance wrought magnesium alloys. The strengthening in two-phase composites (I-phase + α -Mg) can be explained by dispersion hardening due to the presence of I-phase particles and by the strong bonding property at the I-phase/matrix interface. The presence of an additional secondary solidification phase can further enhance formability and mechanical properties. In Mg-Zn-Y alloys, the co-presence of I and Ca 2 Mg 6 Zn 3 phases by addition of Ca can significantly enhance formability, while in Mg-Zn-Al alloys, the co-presence of the I-phase and Mg 2 Sn phase leads to the enhancement of mechanical properties. Dynamic and static recrystallization are significantly accelerated by addition of Ca in Mg-Zn-Y alloy, resulting in much smaller grain size and more random texture. The high strength of Mg-Zn-Al-Sn alloys is attributed to the presence of finely distributed Mg 2 Sn and I-phase particles embedded in the α -Mg matrix.

Enhanced superconducting properties of MgB2 by carbon substitution using carbon containing nano additives

International Nuclear Information System (INIS)

Devadas, K.M.; Varghese, Neson; Vinod, K.; Rahul, S.; Thomas, Syju; Anooja, J.B.; Syamaprasad, U.; Sundaresan, A.; Roy, S.B.

2010-01-01

A comparative study on the effect of doping of nano carbon, nano diamond and nano SiC in MgB 2 is carried out. The J c (H) is significantly enhanced for all doped samples compared to the pure sample among which MgB 1.9 C 0.1 (nano C) exhibits the best J c (H) performance. The enhanced performance is due to the effective substitution of C at B site which is confirmed by the systematic decrease in both α axis and T c . (author)

Mechanochemical Synthesis of Nanostructured MgXNi1-XO Compound by Mg-NiO Mixture

Directory of Open Access Journals (Sweden)

Nader Setoudeh

2017-06-01

Full Text Available Synthesis of magnesium nickel oxide phase such as MgxNi1-xO solid solutions has been studied in this research article using mechnochmical reaction between magnesium and nickel oxide. Mixtures of magnesium powder and nickel oxide (Mg+NiO with stoichiometric compositions were milled for different times in a planetary ball mill. Reduction reaction of nickel oxide by magnesium via a mechanically induced self-sustaining reaction (MSR was confirmed in the XRD measurements of the as-milled samples. Formation of nanostructured magnesium nickel oxide phases (such as Mg0.4Ni0.6O or MgNiO2 was observed after isothermal heating of the 30 minutes milled samples at 1000°C where nickel phase seems to disappear in XRD patterns. The traces of phases such as Mg0.4Ni0.6O or MgNiO2 were also observed in the as-milled mixtures. Therefore, the XRD results of the as-milled samples suggested that the formation of magnesium nickel oxide phases could be possible even after prolonged milling. The XRD and SEM results of both as-milled and isothermally heated samples indicated that the crystallite size and particle size of the final products reached to nanoscale after milling. Morphological and compositional evolution of the samples after heat treatment was monitored through SEM imaging and elemental analyses. The results confirmed that the composition of final product is close to Mg0.4Ni0.6O compound.

Effect of CeLa addition on the microstructures and mechanical properties of Al-Cu-Mn-Mg-Fe alloy

International Nuclear Information System (INIS)

Du, Jiandi; Ding, Dongyan; Xu, Zhou; Zhang, Junchao; Zhang, Wenlong; Gao, Yongjin; Chen, Guozhen; Chen, Weigao; You, Xiaohua; Chen, Renzong; Huang, Yuanwei; Tang, Jinsong

2017-01-01

Development of high strength lithium battery shell alloy is highly desired for new energy automobile industry. The microstructures and mechanical properties of Al-Cu-Mn-Mg-Fe alloy with different CeLa additions were investigated through optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Rietveld refinement and tensile testing. Experimental results indicate that Al 8 Cu 4 Ce and Al 6 Cu 6 La phases formed due to CeLa addition. Addition of 0.25 wt.% CeLa could promote the formation of denser precipitation of Al 20 Cu 2 Mn 3 and Al 6 (Mn, Fe) phases, which improved the mechanical properties of the alloy at room temperature. However, up to 0.50 wt.% CeLa addition could promote the formation of coarse Al 8 Cu 4 Ce phase, Al 6 Cu 6 La phase and Al 6 (Mn, Fe) phase, which resulted in weakened mechanical properties. - Highlights: •Al-Cu-Mn-Mg-Fe alloys with different CeLa addition were fabricated through casting and rolling. •Al 8 Cu 4 Ce and Al 6 Cu 6 La phases formed after CeLa addition. •Addition of 0.25 wt.% CeLa promoted formation of denser precipitates of Al 20 Cu 2 Mn 3 and Al 6 (Mn, Fe). •Mechanical properties of the alloy was improved after 0.25 wt.% CeLa addition.

In vitro propagation of garlic ( Allium sativum L.) through adventitious ...

African Journals Online (AJOL)

, Balady, Sids 40 and VFG 180 (3 - 1) as well as a garlic wild type through adventitious shoot organogenesis. Shoot and root apices were subjected to eight callus induction treatments. A combination of 1 mg L-1 2,4-D + 5 mg L-1 BA + 5 mg L-1 ...

Malignant Mesothelioma Effusions Are Infiltrated by CD3+ T Cells Highly Expressing PD-L1 and the PD-L1+ Tumor Cells within These Effusions Are Susceptible to ADCC by the Anti-PD-L1 Antibody Avelumab.

Science.gov (United States)

Khanna, Swati; Thomas, Anish; Abate-Daga, Daniel; Zhang, Jingli; Morrow, Betsy; Steinberg, Seth M; Orlandi, Augusto; Ferroni, Patrizia; Schlom, Jeffrey; Guadagni, Fiorella; Hassan, Raffit

2016-11-01

The functional aspects of programmed death 1 (PD-1) and PD ligand 1 (PD-L1) immune checkpoints in malignant mesothelioma have not been studied. Tumor samples from 65 patients with mesothelioma were evaluated for PD-L1 expression by immunohistochemistry, and its prognostic significance was examined. Malignant effusions from patients with pleural and peritoneal mesothelioma were evaluated for PD-1-positive and PD-L1-positive infiltrating lymphocytes and their role in inducing PD-L1 expression in tumor cells. Antibody-dependent cellular cytotoxicity (ADCC) of avelumab, a fully humanized immunoglobulin G1 anti PD-L1 antibody against primary mesothelioma cell lines, was evaluated in presence of autologous and allogeneic natural killer cells. Of 65 pleural and peritoneal mesothelioma tumors examined, 41 (63%) were PD-L1-positive, which was associated with slightly inferior overall survival compared to patients with PD-L1-negative tumors (median 23.0 versus 33.3 months, p = 0.35). The frequency of PD-L1 expression was similar in patients with pleural and peritoneal mesothelioma, with 62% and 64% of samples testing positive, respectively. In nine mesothelioma effusion samples evaluated, the fraction of cells expressing PD-L1 ranged from 12% to 83%. In seven patients with paired malignant effusion and peripheral blood mononuclear cell (PBMC) samples, PD-L1 expression was significantly higher on CD3-positive T cells present in malignant effusions as compared with PBMCs (p = 0.016). In addition, the numbers of CD14-positive PD-1-positive cells were increased in malignant effusions compared with PBMCs (p = 0.031). The lymphocytes present in malignant effusions recognized autologous tumor cells and induced interferon-γ-mediated PD-L1 expression on the tumor cell surface. Of the three primary mesothelioma cell lines tested, two were susceptible to avelumab-mediated ADCC in the presence of autologous natural killer cells. Most pleural as well as peritoneal mesotheliomas

Sorption of selenium on Mg-Al and Mg-Al-Eu layered double hydroxides

International Nuclear Information System (INIS)

Curtius, H.; Paparigas, Z.; Kaiser, G.

2008-01-01

H values, was obtained within 5 h for an initial selenite concentration of 4.28 x 10 -13 mol/L. Selenite in water sorbed quantitatively on both LDHs. In MgCl 2 -rich brine a different behaviour to water was observed. The sorption was not quantitatively, due to the presence of high amounts of chloride anions. Chloride, as competing anion, affected the sorption behaviour of selenite. Using a LDH concentration of 0.1 g/L, the sorption of selenite was negligible

A 6-year follow-up of a randomized prospective trial comparing methimazole treatment with or without exogenous L-thyroxine in Chinese patients with Graves' disease.

Science.gov (United States)

Liu, X; Qiang, W; Liu, X; Liu, L; Liu, S; Gao, A; Gao, S; Shi, B

2014-11-01

Antithyroid drug therapy is one of the main medical treatments for Graves' disease. There have been conflicting reports as to whether the addition of exogenous L-thyroxine improves remission rates more than antithyroid drugs alone. This randomized, controlled and prospective clinical trial was undertaken to investigate the long-term outcome of methimazole treatment with or without exogenous L-thyroxine in Chinese patients. 145 patients with Graves' disease were randomly divided into 3 groups and all patients initially received 30 mg of methimazole daily for at least 1 month and then followed the titration -regimen with or without L-thyroxine: group 1 (30 mg→20 mg→15 mg→10 mg→5 mg); group 2 (30 mg→20 mg→15 mg→10 mg+L-thyroxine→5 mg+L-thyroxine); group 3 (30 mg→20 mg→15 mg→10 mg+L-thyroxine→5 mg+L-thyroxine→2.5 mg+L-thyroxine). The drug therapy was discontinued after 5 months of the final dose. 16 out of 46 patients in group 1 (34.8%), 12 out of 47 in group 2 (25.5%) and 16 out of 52 in group 3 (30.8%) had a recurrence of Graves' disease within 6-year follow-up after drug withdrawal. Survival Analysis showed no significant differences in the remission rates between any 2 groups, despite the remission rates in group 2 and 3 were slightly higher than that in group 1. The addition of L-thyroxine to methimazole treatment in patients with Graves' disease neither improves nor prevents the remission or recurrence of Graves' disease in China. © J. A. Barth Verlag in Georg Thieme Verlag KG Stuttgart · New York.

Development and Quality Evaluation of Ready to Serve (RTS Beverage from Cape Gooseberry (Physalis peruviana L.

Directory of Open Access Journals (Sweden)

R. Hemalatha

2018-06-01

Full Text Available This study aimed to develop a process for the development of ready to serve (RTS beverages from enzyme liquefied (pectinase Cape gooseberry juice with additives and preservatives. Storage stability of the RTS beverage at both refrigerated temperature (LT: 4 ± 1 °C and room temperature (RT: 27 ± 2 °C were evaluated for 90 days for microbial, sensorial and physicochemical quality parameters. The stability of RTS beverage stored at LT (4 ± 1 °C was excellent with a retention of the primary quality attributes ascorbic acid (15.44 mg/100 mL, total phenolic content (15.50 mg GAE/100 mL, total carotene (1.07 mg/100 mL, β-carotene (0.78 mg/100 mL, high viscosity (30.29 cp, and with high sensory scores of the product (8.3 up to 90 days as compared to the overall acceptability (6.5 of RT stored RTS for 60 days. Additionally, both the LT and RT stored RTS beverages had microbial counts within the permissible limits. Therefore, both beverages were safe to consume at the end of storage duration. In conclusion, the RTS beverage developed from Cape gooseberry could be served as functional health drink alternative to synthetic soft drinks due to its unique features (high nutritive values, high organoleptic values and high stability of the product.

Novel transporters from Kluyveromyces marxianus and Pichia guilliermondii expressed in Saccharomyces cerevisiae enable growth on L-arabinose and D-xylose.

Science.gov (United States)

Knoshaug, Eric P; Vidgren, Virve; Magalhães, Frederico; Jarvis, Eric E; Franden, Mary Ann; Zhang, Min; Singh, Arjun

2015-10-01

Genes encoding L-arabinose transporters in Kluyveromyces marxianus and Pichia guilliermondii were identified by functional complementation of Saccharomyces cerevisiae whose growth on L-arabinose was dependent on a functioning L-arabinose transporter, or by screening a differential display library, respectively. These transporters also transport D-xylose and were designated KmAXT1 (arabinose-xylose transporter) and PgAXT1, respectively. Transport assays using L-arabinose showed that KmAxt1p has K(m) 263 mM and V(max) 57 nM/mg/min, and PgAxt1p has K(m) 0.13 mM and V(max) 18 nM/mg/min. Glucose, galactose and xylose significantly inhibit L-arabinose transport by both transporters. Transport assays using D-xylose showed that KmAxt1p has K(m) 27 mM and V(max) 3.8 nM/mg/min, and PgAxt1p has K(m) 65 mM and V(max) 8.7 nM/mg/min. Neither transporter is capable of recovering growth on glucose or galactose in a S. cerevisiae strain deleted for hexose and galactose transporters. Transport kinetics of S. cerevisiae Gal2p showed K(m) 371 mM and V(max) 341 nM/mg/min for L-arabinose, and K(m) 25 mM and V(max) 76 nM/mg/min for galactose. Due to the ability of Gal2p and these two newly characterized transporters to transport both L-arabinose and D-xylose, one scenario for the complete usage of biomass-derived pentose sugars would require only the low-affinity, high-throughput transporter Gal2p and one additional high-affinity general pentose transporter, rather than dedicated D-xylose or L-arabinose transporters. Additionally, alignment of these transporters with other characterized pentose transporters provides potential targets for substrate recognition engineering. Copyright © 2015 John Wiley & Sons, Ltd.

Mg-doped nano ferrihydrite - A new adsorbent for fluoride removal from aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Mohapatra, M., E-mail: mamatamohapatra@yahoo.com [Institute of Minerals and Materials Technology, Bhubaneswar 751 013, Orissa (India); Hariprasad, D.; Mohapatra, L.; Anand, S.; Mishra, B.K. [Institute of Minerals and Materials Technology, Bhubaneswar 751 013, Orissa (India)

2012-03-01

The present study evaluates synthesized Mg-doped nano ferrihydrite powder as an adsorbent for F{sup -} removal from aqueous solutions. High surface area Mg-doped ferrihydrite was prepared by co-precipitation method under controlled conditions. Samples were prepared by varying Mg content in the range of 0.39-1.12%. Preliminary test work revealed that under similar conditions, with the increase in Mg content from 0.39 to 0.98% in doped ferrihydrite, % F{sup -} adsorption increased from 66 to 91%. Hence this sample was characterized by XRD, TEM, SAED and TG-DTA. Batch adsorption experiments were carried out by varying contact time (30-480 min), initial pH (1.0-10), initial fluoride concentration (10-150 mg/L), adsorbent dose (0.5-4 g/L), temperature (20-45 Degree-Sign C) and Cl{sup -} or SO{sub 4}{sup 2-} concentrations (nil to 50 mg/L). The results showed 0.98% Mg-doped ferrihydrite to be an excellent fluoride adsorbent giving maximum adsorption capacity of 64 mg/g. The time data fitted well to pseudo second order kinetic model. The isothermal data followed Langmuir model. Thermodynamic parameters confirmed the adsorption process to be spontaneous and endothermic. 89% of fluoride could be desorbed from loaded sample using 1 M NaOH.

Mutation of Aspergillus oryzae for improved production of 3, 4-dihydroxy phenyl-L-alanine (L-DOPA from L-tyrosine Mutação de Aspergillus orizae para produção melhorada de 3,4-dihidroxi fenil-L-alanina (L-DOPA a partir de L-tirosina

Directory of Open Access Journals (Sweden)

Ikram-ul Haq

2006-03-01

Full Text Available Aspergillus oryzae mutant strain UV-7 was further improved for the production of L-DOPA from L-tyrosine using chemical mutation. Different putative mutant strains of organism were tested for the production of L-DOPA in submerged fermentation. Among these putative mutant strains, mutant designated SI-12 gave maximum production of L-DOPA (300 mg L-DOPA.g-1 cells. The production of L-DOPA from different carbon source solutions (So= 30 g.l-1 by mutant culture was investigated at different nitrogen sources, initial pH and temperature values. At optimum pH (pHo= 5.0, and temperature (t=30ºC, 100% sugars were utilized for production and cell mass formation, corresponding to final L-DOPA product yield of 150 mg.g-1 substrate utilized, and maximum volumetric and specific productivities of 125 mg.l-1.h-1, and 150 mg.g-1 cells. h-1, respectively. There was up to 3-fold enhancement in product formation rate. This enhancement is the highest reported in literature. To explain the kinetic mechanism of L-DOPA formation and thermal inactivation of tyrosinase, the thermodynamic parameters were determined with the application of Arrhenius model: activation enthalpy and entropy for product formation, in case of mutant derivative, were 40 k j/mol and 0.076 k j/mol. K for L-DOPA production and 116 k j/mol and 0.590 k j/mol. K for thermal inactivation, respectively. The respective values for product formation were lower while those for product deactivation were higher than the respective values for the parental culture. Therefore, the mutant strain was thermodynamically more resistant to thermal denaturation.A produção de L-DOPA a partir de tirosina pela cepa mutante de Aspergillus orizae UV-7 foi melhorada através de mutação química. Diferentes cepas foram testadas quanto a produção de L-DOPA por fermentação submersa, observando-se que a cepa denominada SI-12 foi a melhor produtora (300 mg de L-DOPA por g de células. A produção de L-DOPA pela cepa

Gypenosides attenuate the development of L-DOPA-induced dyskinesia in 6-hydroxydopamine-lesioned rat model of Parkinson's disease.

Science.gov (United States)

Shin, Keon Sung; Zhao, Ting Ting; Park, Keun Hong; Park, Hyun Jin; Hwang, Bang Yeon; Lee, Chong Kil; Lee, Myung Koo

2015-04-21

Gypenosides (GPS) and ethanol extract of Gynostemma pentaphyllum (GP-EX) show anxiolytic effects on affective disorders in 1-methyl-4-phenyl-1,2,3,6-tetrahydropyridine-lesioned mouse model of Parkinson's disease (PD). Long-term administration of L-3,4-dihydroxyphenylalanine (L-DOPA) leads to the development of severe motor side effects such as L-DOPA-induced-dyskinesia (LID) in PD. The present study investigated the effects of GPS and GP-EX on LID in a 6-hydroxydopamine (6-OHDA)-lesioned rat model of PD. Daily administration of L-DOPA (25 mg/kg) in the 6-OHDA-lesioned rat model of PD for 22 days induced expression of LID, which was determined by the body and locomotive AIMs scores and contralateral rotational behaviors. However, co-treatments of GPS (25 and 50 mg/kg) or GP-EX (50 mg/kg) with L-DOPA significantly attenuated the development of LID without compromising the anti-parkinsonian effects of L-DOPA. In addition, the increases in ∆FosB expression and ERK1/2 phosphorylation in 6-OHDA-lesioned rats induced by L-DOPA administration were significantly reduced by co-treatment with GPS (25 and 50 mg/kg) or GP-EX (50 mg/kg). These results suggest that GPS (25 and 50 mg/kg) and GP-EX (50 mg/kg) effectively attenuate the development of LID by modulating the biomarker activities of ∆FosB expression and ERK1/2 phosphorylation in the 6-OHDA-lesioned rat model of PD. GPS and GP-EX will be useful adjuvant therapeutics for LID in PD.

Magnetic properties and critical current density of bulk MgB2 polycrystalline with Bi-2212 addition

International Nuclear Information System (INIS)

Shen, T M; Li, G; Zhu, X T; Cheng, C H; Zhao, Y

2005-01-01

Bulk samples of MgB 2 were prepared with 0, 3, 5, and 10 wt% Bi 2 Sr 2 CaCu 2 O 8 (Bi-2212) particles, added using a simple solid-state reaction route in order to investigate the effect of inclusions of a material with higher T c than the superconducting matrix. The density, diamagnetic signal, and critical current density, J c , of the samples change significantly with the doping level. It is found that J c is significantly enhanced by the Bi-2212 addition. Microstructural analysis indicates that a small amount of Bi-2212 is decomposed into Cu 2 O and other impurity phases while a significant amount of unreacted Bi-2212 particles remains in MgB 2 matrix, and these act as effective pinning centres for vortices. The enhanced pinning force is mainly attributable to these highly dispersed inclusions inserted in the MgB 2 grains. Despite the effectiveness of the high-T c inclusions in increasing superconducting critical currents in our experiment, our results seem to demonstrate the superiority of attractive centres over repulsive ones. A pinning mechanism is proposed to account for the contribution of this type of pinning centre in MgB 2 superconductors. (rapid communication)

Sr, Mg cosubstituted HA porous macro-granules: potentialities as resorbable bone filler with antiosteoporotic functions.

Science.gov (United States)

Landi, Elena; Uggeri, Jacopo; Medri, Valentina; Guizzardi, Stefano

2013-09-01

Porous macro-granules of nanostructured apatite with Ca ions partially cosubstituted with Mg and Sr ions in different ratios (SrMgHAs), were synthesized at 37°C and compared with Mg and/or Sr free apatites (MgHAs and HA). Strontium improved the Mg substitution extent in the apatite and the chemical-physical and thermal stability of the resulting cosubstituted apatite. Porous macro-granules of 400-600 micron with selected composition were tested for the ionic release in synthetic body fluid and the data were related with the results of preliminary cell investigation in vitro. As compared to the corresponding Sr-free granulate, the SrMgHA could be exploited to prolong the beneficial Mg release during the bone regeneration process. In addition the contemporary in situ supply of Sr, an antiosteoporotic and anticarie ion, could influence the quality of new hard tissues. The ionic multirelease created a more favorable environment for human osteoblasts, demonstrated by a proliferative effect for each dose tested in the range 0.1-10 mg/mL. Copyright © 2013 Wiley Periodicals, Inc.

Implementation Study of Patient-Ready Syringes Containing 25 mg/mL Methotrexate Solution for Use in Treating Ectopic Pregnancy

Directory of Open Access Journals (Sweden)

R. Respaud

2014-01-01

Full Text Available Background. Ectopic pregnancy (EP is a significant cause of morbidity and mortality during the first trimester of pregnancy. Small unruptured tubal pregnancies can be treated medically with a single dose of methotrexate (MTX. Objective. The aim of this study was to evaluate the stability of a 25 mg/mL solution of MTX to devise a secure delivery circuit for the preparation and use of this medication in the management of EP. Method. MTX solutions were packaged in polypropylene syringes, stored over an 84-day period, and protected from light either at +2 to +8°C or at 23°C. We assessed the physical and chemical stability of the solutions at various time points over the storage period. A pharmaceutical delivery circuit was implemented that involved the batch preparation of MTX syringes. Results. We show that 25 mg/mL MTX solutions remain stable over an 84-day period under the storage conditions tested. Standard doses were prepared, ranging from 50 mg to 100 mg. The results of this study suggest that MTX syringes can be prepared in advance by the pharmacy, ready to be dispensed at any time that a diagnosis of EP is made. Conclusion. The high stability of a 25 mg/mL MTX solution in polypropylene syringes makes it possible to implement a flexible and cost-effective delivery circuit for ready-to-use preparations of this drug, providing 24-hour access and preventing treatment delays.

Efficacy of Additional Canagliflozin Administration to Type 2 Diabetes Patients Receiving Insulin Therapy: Examination of Diurnal Glycemic Patterns Using Continuous Glucose Monitoring (CGM).

Science.gov (United States)

Matsumura, Mihoko; Nakatani, Yuki; Tanka, Seiichi; Aoki, Chie; Sagara, Masaaki; Yanagi, Kazunori; Suzuki, Kunihiro; Aso, Yoshimasa

2017-08-01

The efficacy of administering a sodium-glucose cotransporter 2 inhibitor during insulin therapy has not been established. In this study, we examined its effects based on diurnal glycemic patterns using continuous glucose monitoring (CGM). The subjects were 15 patients who had received insulin therapy for 1 year or more. A CGM device was attached to all subjects for 1 week. The administration of canagliflozin at 100 mg was started 4 days after attachment. The mean glucose concentrations, standard deviation (SD), mean amplitude of glycemic excursions (MAGE), mean of daily difference of blood glucose (MODD), and area under the curve (AUC) (≥180, glucose concentrations decreased from 161.1 to 139.1 mg/dL (P AUC of ≥180, i.e., the total area of blood glucose levels at or above 180 on the blood glucose curve of CGM, decreased from 339.1 to 113.6 mg/dL (P AUC of blood glucose levels below 70 on the blood glucose curve of CGM, slightly decreased from 1.6 to 0.3 mg/dL (P = 0.08). The total number of basal insulin units decreased from 128 to 76, and that of bolus insulin decreased from 266 to 154; the dose of insulin could be markedly decreased. In addition, the mean 8-OHdG level decreased from 11.4 to 10.8 ng/mg Cre (P blood glucose changes in type 2 diabetes using insulin. In addition, the results suggest its antioxidant actions. University Hospital Medical Information Network (UMIN no. 000019429).

[Can the treatment with L-carnitine improve the inflammation in chronic hemodialysis patients?].

Science.gov (United States)

Grazi, G; Meriggioli, M; Donati, G

2004-01-01

Inflammation in patients on chronic hemodialysis (HD) is related to malnutrition and atherosclerosis; anemia is also often present in these patients. It has been demonstrated that l-carnitina treatment, in addition to reducing the need for erythropoietin (EPO), improves nutritional parameters and cardiac performance. To evaluate the effect of l-carnitine on the inflammatory pathology in patients on chronic HD, we studied 11 patients with no sure signs of malnutrition, flogistic and infective pathologies and with C-reactive protein (CRP) <2 mg/dL. We evaluated at baseline, after 6 and 12 months CRP, serum albumin, hemoglobin (Hb),nPCR and EPO weekly requirement. We observed a reduction in CRP (from 0.88 +/- 0.65 to 0.42 +/- 0.17 mg/dL after 6 months and to 0.50 + 0.36 mg/dL after 12 months), an increase in serum albumin (from 10.9 +/- 1.23 to 2.08 +/- 1.88 and to 11.8 +/- 1.15 g/dL) and an increase in nPCR (from 0.96 +/- 0.09 to 1.15 +/- 0.2 and to 1.16 +/- 0.18 g/kg/die); EPO weekly requirement decreased (from 7363 +/- 2941 to 5909 +/- 3207 units after 6 months and to 5363 +/- 3139 units after 12 months). These results seem to underline a positive effect of l-carnitine on the inflammatory pathology of patients on chronic hemodialytic treatment.

Does Biochar Addition Inlfuence the Change Points of Soil Phosphorus Leaching?

Institute of Scientific and Technical Information of China (English)

ZHAO Xiao-rong; LI Dan; KONG Juan; LIN Qi-mei

2014-01-01

Phosphorus change point indicating the threshold related to P leaching, largely depends on soil properties. Increasing data have shown that biochar addition can improve soil retention capacity of ions. However, we have known little about weather biochar amendment inlfuence the change point of P leaching. In this study, two soils added with 0, 5, 10, 20, and 50 g biochar kg-1 were incubated at 25°C for 14 d following adjusting the soil moisture to 50%water-holding capacity (WHC). The soils with different available P values were then obtained by adding a series of KH2PO4 solution (ranging from 0 to 600 mg P kg-1 soil), and subjecting to three cycles of drying and rewetting. The results showed that biochar addition signiifcantly lifted the P change points in the tested soils, together with changes in soil pH, organic C, Olen-P and CaCl2-P but little on exchangeable Ca and Mg, oxalate-extractable Fe and Al. The Olsen-P at the change points ranged from 48.65 to 185.07 mg kg-1 in the alluvial soil and 71.25 to 98.65 mg kg-1 in the red soil, corresponding to CaCl2-P of 0.31-6.49 and 0.18-0.45 mg L-1, respectively. The change points of the alluvial soil were readily changed by adding biochar compared with that of the red soil. The enhancement of change points was likely to be explained as the improvement of phosphate retention ability in the biochar-added soils.

On the Link Between L1-PCA and ICA.

Science.gov (United States)

Martin-Clemente, Ruben; Zarzoso, Vicente

2017-03-01

Principal component analysis (PCA) based on L1-norm maximization is an emerging technique that has drawn growing interest in the signal processing and machine learning research communities, especially due to its robustness to outliers. The present work proves that L1-norm PCA can perform independent component analysis (ICA) under the whitening assumption. However, when the source probability distributions fulfil certain conditions, the L1-norm criterion needs to be minimized rather than maximized, which can be accomplished by simple modifications on existing optimal algorithms for L1-PCA. If the sources have symmetric distributions, we show in addition that L1-PCA is linked to kurtosis optimization. A number of numerical experiments illustrate the theoretical results and analyze the comparative performance of different algorithms for ICA via L1-PCA. Although our analysis is asymptotic in the sample size, this equivalence opens interesting new perspectives for performing ICA using optimal algorithms for L1-PCA with guaranteed global convergence while inheriting the increased robustness to outliers of the L1-norm criterion.

The effects of Cu addition on the microstructure and thermal stability of an Al-Mg-Si alloy

International Nuclear Information System (INIS)

Man, Jin; Jing, Li; Jie, Shao Guang

2007-01-01

The effects of Cu addition on the microstructure and thermal stability of 6082 Al-Mg-Si alloys were investigated. The results show the Q' precipitates are formed when aged at 170 o C for 4 h in 6082 alloy with 0.6% Cu addition. The hardness value of the alloy with 0.6% Cu is always distinctly higher than that of the alloy without Cu during isothermal treatment at 250 o C. Based on the TEM and three-dimensional atom probe (3DAP) results, the thermal stability of the 6082 alloys with Cu addition is discussed with respect to the distribution of Cu

The Effects of Dy Addition on Microstructure and Mechanical Properties of the As-Cast Mg-5Al-3Ca-2Nd Alloys.

Science.gov (United States)

Son, Hyeon-Taek; Kim, Yong-Ho; Yoo, Hyo-Sang

2018-03-01

The microstructure of the as-cast Mg-5Al-3Ca-2Nd-xDy alloys consists of α-Mg matrix, (Mg, Al)2Ca eutectic phase, Al-Nd and Al-Dy intermetallic compounds. α-Mg matrix morphology was changed from dendritic to equiaxed with the increase Dy addition. And grain size was remarkably refined. As Dy content was increased, yield strength was improved due to the refined grains and the homogeneous distribution of Al-Dy phase.

Effect of Gd–Ca combined additions on the microstructure and creep properties of Mg–7Al–1Si alloys

International Nuclear Information System (INIS)

Liu, Jian; Wang, Wuxiao; Zhang, Sha; Zhang, Dongjie; Zhang, Haiyan

2015-01-01

Highlights: • The effect of compound addition of Ca and Gd on the microstructure and creep properties of Mg–7Al–1Si alloys was investigated. • After adding 1 wt.% of (Ca + Gd), the creep strain and steady-state creep rate were reduced by about 80% and 84%, respectively. • After adding 1 wt.% of (Ca + Gd), the creep properties of Mg–7Al–1Si alloys were superior to that containing single Gd additive. • The improvement of creep properties after compound addition of Gd and Ca is a result of multiple factors. - Abstract: The microstructure and creep properties of Mg–7Al–1Si alloys with combined additions of alkaline earth element Ca and rare earth element (RE) Gd were investigated using scanning electron microscope (SEM), optical microscope, energy dispersive spectrometer (EDS), X-ray diffraction (XRD), and compressive creep tests. It was found that the combined additions of Ca and Gd contributed to grain refinement, modification of the morphology of coarse Chinese script Mg 2 Si phase, and reduction of β-Mg 17 Al 12 content. Mg–7Al–1Si alloys containing 1 wt.% compound modifier (0.5 wt.% Gd + 0.5 wt.% Ca) exhibited the minimal steady-state creep rate, and were even superior to Mg–7Al–1Si alloys containing single Gd addition. The great improvement of creep properties is mainly attributed to the reduction in the amount and continuity of eutectic β-Mg 17 Al 12 phase, morphology modification of Mg 2 Si phase, solution strengthening of Gd, as well as the formation of thermally stable intermetallic Al 2 Gd, which acted as an effective barrier against grain boundary sliding and dislocation movement

A density functional study of NO{sub 2} adsorption on perfect and defective MgO (1 0 0) and Li/MgO (1 0 0) surfaces

Energy Technology Data Exchange (ETDEWEB)

Eid, Kh.M., E-mail: Khaled_eid@edu.asu.edu.eg [Physics Department, Faculty of Education, Ain Shams University, P.O. Box 11757, Cairo (Egypt); Ammar, H.Y. [Physics Department, Faculty of Education, Ain Shams University, P.O. Box 11757, Cairo (Egypt); Department of Physics, Faculty of Science, Najran University, Najran (Saudi Arabia)

2012-07-15

The density functional theory (DFT) in combination with embedded cluster model have been used to study the adsorption of nitrogen dioxide molecule (NO{sub 2}) on Li atom deposited on the surfaces of metal oxide MgO (1 0 0) on both anionic (O{sup 2-}) and defect (F{sub s} and F{sub s}{sup +}-centers) sites. The adsorption energy (E{sub ads}) of NO{sub 2} molecule (N-down as well as O-down) in different positions on O{sup -2}, F{sub s} and F{sub s}{sup +}-sites is considered. The geometrical optimizations have been done for the additive materials and MgO substrate surfaces. The formation energies have been evaluated for F{sub s} and F{sub s}{sup +} of MgO substrate surfaces. The ionization potential (IP) and electron affinity (eA) for defect free and defect containing surfaces have been calculated. The adsorption properties of NO{sub 2} are analyzed in terms of the adsorption energy, the electron donation (basicity), the elongation of N-O bond length and the atomic charges on adsorbed materials. The densities of states (DOS) have been calculated and used for examining the adsorption properties. The NO{sub 2} molecule is dissociated due to the interaction with the defective substrate surface (F{sub s}-site) producing an oxygen atom strongly chemisorbed to the vacancy of the substrate and gaseous NO far away from the surface. The presence of the Li atom increases the surface chemistry of the anionic O{sup 2-}-site of MgO substrate surfaces (converted from physisorption to chemisorption). On the other hand, the presence of the Li atom decreases the surface chemistry of the F{sub s} and F{sub s}{sup +}-sites of MgO substrate surfaces. Generally, the NO{sub 2} molecule is strongly adsorbed (chemisorption) on the MgO substrate surfaces containing F{sub s} and F{sub s}{sup +}-centers.

Mg1-xZnxFe2O4 nanoparticles: Interplay between cation distribution and magnetic properties

Directory of Open Access Journals (Sweden)

S. Raghuvanshi

2018-04-01

Full Text Available Correlation between cationic distribution, magnetic properties of Mg1-xZnxFe2O4 (0.0 ≤ x ≤ 1.0 ferrite is demonstrated, hardly shown in literature. X-ray diffraction (XRD confirms the formation of cubic spinel nano ferrites with grain diameter between 40.8 to 55.4 nm. Energy dispersive spectroscopy (EDS confirms close agreement of Mg/Fe, Zn/Fe molar ratio, presence of all elements (Mg, Zn, Fe, O, formation of estimated ferrite composition. Zn addition (for Mg shows: i linear increase of lattice parameter aexp, accounted for replacement of an ion with higher ionic radius (Zn > Mg; ii presence of higher population of Fe3+ ions on B site, and unusual occurrence of Zn, Mg on A and B site leads to non-equilibrium cation distribution where we observe inverse to mixed structure, and is in contrast to reported literature where inverse to normal transition is reported; iii effect on A-A, A-B, B-B exchange interactions, affecting coercivity Hc, Ms. A new empirical relation is also obtained showing linear relation between saturation magnetization Ms – inversion parameter δ, oxygen parameter u4¯3m. Non-zero Y-K angle (αYK values implies Y-K type magnetic ordering in the studied samples.

Microstructure and properties of hot extruded Mg-3Zn-Y-xCu (x = 0, 1, 3, 5) alloys

Energy Technology Data Exchange (ETDEWEB)

Liu, Bao-sheng; Kuang, Ya-fei; Fang, Da-qing; Chai, Yue-sheng [Taiyuan Univ. of Science and Technology (China). College of Materials Science and Engineering; Taiyuan Univ. of Science and Technology (China). Engineering Research Center for Magnesium Alloys of Shanxi Province; Zhang, Yue-zhong [Taiyuan Univ. of Science and Technology (China). Engineering Research Center for Magnesium Alloys of Shanxi Province; Taiyuan Univ. of Science and Technology (China). College of Chemical and Biological Engineering

2017-04-15

In petroleum drilling engineering, materials with high strength and rapid degradation are required for degradable fracturing ball applications. In this work, the microstructure, mechanical properties, and corrosion behavior of extruded Mg-3Zn-Y-xCu (x = 0, 1, 3, 5 weight percent) alloys are investigated using optical microscopy, scanning electronic microscopy equipped with energy dispersive X-ray spectroscopy, X-ray diffraction, transmission electronic microscopy, compression tests, electrochemical measurements, and hydrogen evolution tests, to explore their potential as excellent candidate alloys for degradable fracturing ball applications. It is found that the Mg-3Zn-Y alloy is mainly composed of α-Mg, Mg{sub 3}Zn{sub 3}Y{sub 2}, and Mg{sub 3}Zn{sub 6}Y phases. After Cu addition, a new MgZnCu phase is formed, while the Mg{sub 3}Zn{sub 3}Y{sub 2} phase disappears. The Mg-3Zn-Y-3Cu alloy shows the highest compressive strength (473 MPa) and yield strength (402 MPa), mainly attributed to the combined effect of the fine-grain and dispersed precipitation of Mg{sub 3}Zn{sub 6}Y and MgZnCu. The corrosion rate of Mg-3Zn-Y-3Cu reaches 0.41 mm day{sup -1} in 3.5 wt.% KCl solution. Consequently, Mg-3Zn-Y-3Cu alloy is a suitable degradable fracturing ball-seat material.

Effect of CeLa addition on the microstructures and mechanical properties of Al-Cu-Mn-Mg-Fe alloy

Energy Technology Data Exchange (ETDEWEB)

Du, Jiandi [School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Ding, Dongyan, E-mail: dyding@sjtu.edu.cn [School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Xu, Zhou; Zhang, Junchao; Zhang, Wenlong [School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Gao, Yongjin; Chen, Guozhen; Chen, Weigao; You, Xiaohua [Huafon NLM Al Co., Ltd, Shanghai 201506 (China); Chen, Renzong; Huang, Yuanwei; Tang, Jinsong [Shanghai Huafon Materials Technology Institute, Shanghai 201203 (China)

2017-01-15

Development of high strength lithium battery shell alloy is highly desired for new energy automobile industry. The microstructures and mechanical properties of Al-Cu-Mn-Mg-Fe alloy with different CeLa additions were investigated through optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Rietveld refinement and tensile testing. Experimental results indicate that Al{sub 8}Cu{sub 4}Ce and Al{sub 6}Cu{sub 6}La phases formed due to CeLa addition. Addition of 0.25 wt.% CeLa could promote the formation of denser precipitation of Al{sub 20}Cu{sub 2}Mn{sub 3} and Al{sub 6}(Mn, Fe) phases, which improved the mechanical properties of the alloy at room temperature. However, up to 0.50 wt.% CeLa addition could promote the formation of coarse Al{sub 8}Cu{sub 4}Ce phase, Al{sub 6}Cu{sub 6}La phase and Al{sub 6}(Mn, Fe) phase, which resulted in weakened mechanical properties. - Highlights: •Al-Cu-Mn-Mg-Fe alloys with different CeLa addition were fabricated through casting and rolling. •Al{sub 8}Cu{sub 4}Ce and Al{sub 6}Cu{sub 6}La phases formed after CeLa addition. •Addition of 0.25 wt.% CeLa promoted formation of denser precipitates of Al{sub 20}Cu{sub 2}Mn{sub 3} and Al{sub 6}(Mn, Fe). •Mechanical properties of the alloy was improved after 0.25 wt.% CeLa addition.

Direct Fungal Production of Ethanol from High-Solids Pulps by the Ethanol-fermenting White-rot Fungus Phlebia sp. MG-60

Directory of Open Access Journals (Sweden)

Ichiro Kamei

2014-07-01

Full Text Available A white-rot fungus, Phlebia sp. MG-60, was applied to the fermentation of high-solid loadings of unbleached hardwood kraft pulp (UHKP without the addition of commercial cellulase. From 4.7% UHKP, 19.6 g L-1 ethanol was produced, equivalent to 61.7% of the theoretical maximum. The highest ethanol concentration (25.9 g L-1, or 46.7% of the theoretical maximum was observed in the culture containing 9.1% UHKP. The highest filter paper activity (FPase was observed in the culture containing 4.7% UHKP, while the production of FPase in the 16.5% UHKP culture was very low. Temporarily removing the silicone plug from Erlenmeyer flasks, which relieved the pressure and allowed a small amount of aeration, improved the yield of ethanol produced from the 9.1% UHKP, which reached as high as 37.3 g L-1. These results indicated that production of cellulase and ensuing saccharification and fermentation by Phlebia sp. MG-60 is affected by water content and benefits from a small amount of aeration.

Assessment of Direct Regeneration in Germany (Matricaria chamomilla L. and Shirazi Chamomiles (Matricaria recutita L.

Directory of Open Access Journals (Sweden)

A. Masoumiasl

2016-07-01

Full Text Available Introduction: German (Matricaria chamomilla L. and Shirazi (Matricaria recutita L. chamomiles are the most important medicinal plants of the Astraceae family which are used in the pharmaceutical, health, food and cosmetics industries. Production of this plant has been undertaken in Iran mainly in Isfahan, Kohgiluyeh and Boyerahmad, Golestan and Hamedan provinces. In vitro propagation of plants have higher potential to produce qualified natural products, restoring and preserving of endangered plants, induction of somaclonal variation, industrial reproduction, valuable secondary metabolites and increased active ingredients. Researchers reported successful micropropagation system for five chamomile varieties on MS medium contained 0.01 mg/l NAA and 2.5 mg/l kinetin. The aim of this study was to investigate the effects of stem (with and without node, leaf and cotyledon explants and different plant growth regulators on direct regeneration of German and Shirazi chamomiles. Although the Shirazi chamomile is native to Iran, but German chamomile is Iran non-indigenous cultivar. By our knowledge, there have been no comparison reports about responses of these cultivars to tissue culture. Materials and Methods: This research was performed in the central laboratory of Agriculture Faculty in Yasouj University. Seeds were provided from Pakan-Bazr institute, Isfahan. Chamomile seeds were disinfected by ethanol (70% for 5-10 min and sodium hypocholorite 3% for 5-12 min and then washed for several times by distilled water. Then, seeds were sown on MS medium for germination. After 2-3 weeks, seedlings were grown and then planted in MS medium supplemented with hormonal combinations of NAA at two levels (0.1 and 0.5 mg/l, kinetin at three levels (2, 2.5 and 3 mg/l and Zeatin, BAP and 2ip at three levels (0.5, 1 and 1.5 mg/l. The experiment was performed in a completely randomized design with four replications. Factors included explants, cultivars and hormonal

L = ± 1 stellarator

International Nuclear Information System (INIS)

Kikuchi, T.; Shiina, S.; Saito, K.; Gesso, H.; Aizawa, M.; Kawakami, I.

1985-01-01

We report the magnetic field configuration of helical magnetic axis stellarator. The magnetic field configuration is composed of large l=1 field and small l=-1 and l=0(bumpy) fields. The large l=1 field (combined with the small l=-1 field) is used to form helical magnetic axis with the helical curvature much larger than the toroidal curvature, which provides the high limiting values of β. The small l=-1 field, furthermore, as well as the large l=1 field reduces the Pfirsch-Schlueter currents by combining with l=0 field. Therefore, the large l=1 field and the combination of three field components may be favourable for the increase of limiting β value

Novel integration strategy for enhancing chalcopyrite bioleaching by Acidithiobacillus sp. in a 7-L fermenter.

Science.gov (United States)

Feng, Shoushuai; Yang, Hailin; Zhan, Xiao; Wang, Wu

2014-06-01

An integrated strategy (additional energy substrate-three stage pH control-fed batch) was firstly proposed for efficiently improving chalcopyrite bioleaching by Acidithiobacillus sp. in a 7-L fermenter. The strain adaptive-growing phase was greatly shortened from 8days into 4days with the supplement of additional 2g/L Fe(2+)+2g/L S(0). Jarosite passivation was effectively weakened basing on higher biomass via the three-stage pH-stat control (pH 1.3-1.0-0.7). The mineral substrate inhibition was attenuated by fed-batch fermentation. With the integrated strategy, the biochemical reaction was promoted and achieved a better balance. Meanwhile, the domination course of A. thiooxidans in the microbial community was shortened from 14days to 8days. As the results of integrated strategy, the final copper ion and productivity reached 89.1mg/L and 2.23mg/(Ld), respectively, which was improved by 52.8% compared to the uncontrolled batch bioleaching. The integrated strategy could be further exploited for industrial chalcopyrite bioleaching. Copyright © 2014 Elsevier Ltd. All rights reserved.

Stimulation of aerobic degradation of bentazone, mecoprop and dichlorprop by oxygen addition to aquifer sediment

DEFF Research Database (Denmark)

Levi, Suzi; Hybel, Anne-Marie; Bjerg, Poul Løgstrup

2014-01-01

for the herbicides. In the presence of oxygen 14C-labelled bentazone and mecoprop were removed significantly from the two monitoring wells' groundwater samples. Oxygen was added to microcosms in order to investigate whether different oxygen concentrations stimulate the biodegradation of the three herbicides....... The highest oxygen concentrations (corresponding to 4-11mgL-1) stimulated degradation (a 14-27% increase for mecoprop, 3-9% for dichlorprop and 15-20% for bentazone) over an experimental period of 200days. Oxygen was required to biodegrade the herbicides, since no degradation was observed under anaerobic...... conditions. This is the first time bentazone degradation has been observed in aquifer material at low oxygen concentrations (2mgL-1). The sediment had substantial oxygen consumption (0.92-1.45O2g-1dw over 200days) and oxygen was depleted rapidly in most incubations soon after its addition, which might be due...

Optimization of heat treatment parameters for additive manufacturing and gravity casting AlSi10Mg alloy

Science.gov (United States)

Girelli, L.; Tocci, M.; Montesano, L.; Gelfi, M.; Pola, A.

2017-11-01

Additive manufacturing of metals is a production process developed in the last few years to realize net shape components with complex geometry and high performance. AlSi10Mg is one of the most widely used aluminium alloys, both in this field and in conventional foundry processes, for its significant mechanical properties combined with good corrosion resistance. In this paper the effect of heat treatment on AlSi10Mg alloy was investigated. Solution and ageing treatments were carried out with different temperatures and times on samples obtained by direct metal laser sintering and gravity casting in order to compare their performance. Microstructural analyses and hardness tests were performed to investigate the effectiveness of the heat treatment. The results were correlated to the sample microstructure and porosity, analysed by means of optical microscopy and density measurements. It was found that, in the additive manufactured samples, the heat treatment can reduce significantly the performance of the alloy also because of the increase of porosity due to entrapped gas during the deposition technique and that the higher the solution temperature the higher the increase of such defects. A so remarkable effect was not found in the conventional cast alloy.

26 CFR 25.2522(d)-1 - Additional cross references.

Science.gov (United States)

2010-04-01

...) ESTATE AND GIFT TAXES GIFT TAX; GIFTS MADE AFTER DECEMBER 31, 1954 Deductions § 25.2522(d)-1 Additional...) for provisions relating to the claim and allowance of the value of certain easements as a gift under... Housing and Urban Development Act (42 U.S.C. 3535), as added by section 905 of Pub. L. 91-609 (84 Stat...

Bioproduction of L-Aspartic Acid and Cinnamic Acid by L-Aspartate Ammonia Lyase from Pseudomonas aeruginosa PAO1.

Science.gov (United States)

Patel, Arti T; Akhani, Rekha C; Patel, Manisha J; Dedania, Samir R; Patel, Darshan H

2017-06-01

Aspartase (L-aspartate ammonia lyase, EC 4.3.1.1) catalyses the reversible amination and deamination of L-aspartic acid to fumaric acid which can be used to produce important biochemical. In this study, we have explored the characteristics of aspartase from Pseudomonas aeruginosa PAO1 (PA-AspA). To overproduce PA-AspA, the 1425-bp gene was introduced in Escherichia coli BL21 and purified. A 51.0-kDa protein was observed as a homogenous purified protein on SDS-PAGE. The enzyme was optimally active at pH 8.0 and 35 °C. PA-AspA has retained 56% activity after 7 days of incubation at 35 °C, which displays the hyperthermostablility characteristics of the enzyme. PA-AspA is activated in the presence of metal ions and Mg2+ is found to be most effective. Among the substrates tested for specificity of PA-AspA, L-phenylalanine (38.35 ± 2.68) showed the highest specific activity followed by L-aspartic acid (31.21 ± 3.31) and fumarate (5.42 ± 2.94). K m values for L-phenylalanine, L-aspartic acid and fumarate were 1.71 mM, 0.346 μM and 2 M, respectively. The catalytic efficiency (k cat /K m ) for L-aspartic acid (14.18 s -1  mM -1 ) was higher than that for L-phenylalanine (4.65 s -1  mM -1 ). For bioconversion, from an initial concentration of 1000 mM of fumarate and 30 mM of L-phenylalanine, PA-AspA was found to convert 395.31 μM L-aspartic acid and 3.47 mM cinnamic acid, respectively.

LOW-TEMPERATURE SINTERED (ZnMg2SiO4 MICROWAVE CERAMICS WITH TiO2 ADDITION AND CALCIUM BOROSILICATE GLASS

Directory of Open Access Journals (Sweden)

BO LI

2011-03-01

Full Text Available The low-temperature sintered (ZnMg2SiO–TiO2 microwave ceramic using CaO–B2O3–SiO2 (CBS as a sintering aid has been developed. Microwave properties of (Zn1-xMgx2SiO4 base materials via sol-gel method were highly dependent on the Mg-substituted content. Further, effects of CBS and TiO2 additives on the crystal phases, microstructures and microwave characteristics of (ZnMg2SiO4 (ZMS ceramics were investigated. The results indicated that CBS glass could lower the firing temperature of ZMS dielectrics effectively from 1170 to 950°C due to the liquid-phase effect, and significantly improve the sintering behavior and microwave properties of ZMS ceramics. Moreover, ZMS–TiO2 ceramics showed the biphasic structure and the abnormal grain growth was suppressed by the pinning effect of second phase TiO2. Proper amount of TiO2 could tune the large negative temperature coefficient of resonant frequency (tf of ZMS system to a near zero value. (Zn0.8Mg0.22SiO4 codoped with 10 wt.% TiO2 and 3 wt.% CBS sintered at 950°C exhibits the dense microstructure and excellent microwave properties: εr = 9.5, Q·f = 16 600 GHz and tf = −9.6 ppm/°C.

Stability of 2 mg/mL Adenosine Solution in Polyvinyl Chloride and Polyolefin Infusion Bags.

Science.gov (United States)

DeAngelis, Michael; Ferrara, Alexander; Gregory, Kaleigh; Zammit, Kimberly; Zhao, Fang

2018-04-01

Adenosine is a potent endogenous mediator of vasodilation. Compounded sterile solutions of adenosine are used in cardiac catheterization lab to perform stress tests on the heart. These tests are used to determine the fractional flow reserve (FFR) and are commonly used in the management and diagnosis of cardiovascular conditions. The purpose of this study was to assess the physical and chemical stability of 2 mg/mL adenosine in 0.9% Sodium Chloride Injection, USP in polyvinyl chloride [PVC]) and polyolefin infusion bags stored at room temperature (20°C-25°C) and under refrigeration (2°C-8°C). The compounding and analytical methods used in this study were very similar to those described in the prior publications from the authors' laboratory. To ensure a uniform starting concentration of all stability samples, a batch of 2 mg/mL adenosine solution was prepared and then packaged into empty PVC and polyolefin infusion bags. These stability samples were prepared in triplicate for each bag type and storage temperature (a total of 12 samples). The infusion bag samples were assessed for stability immediately after preparation and after 1 day, 3 days, 7 days, and 14 days. At each time point, the infusion bags were first visually inspected against a light background for color change, clarity, and particulates. Aliquots were drawn from each sample at each time point for pH analysis and high-performance liquid chromatography (HPLC) analysis. Over 14 days of storage at room temperature or refrigeration, no considerable change in visual appearance or pH was observed in any bags. All samples retained 90% to 110% of the initial drug concentration. No significant degradation peaks were observed in the HPLC chromatograms.

Enhancement of critical current density of in situ processed MgB sub 2 tapes by WB addition

CERN Document Server

Fujii, H; Kumakura, H

2003-01-01

The effect of tungsten boride (WB) addition on the microstructure and superconducting properties of Fe-sheathed MgB sub 2 tapes has been investigated. The microstructure was not influenced appreciably by the addition, whereas the superconducting properties changed. Even by a 5 mol% addition, the critical temperature (T sub c) decreased by about 0.5 K. However, the field dependence of the inductive critical current density (J sub c sub i) became smaller with the increase in the amount of addition, suggesting that pinning centres effective in a high-field region were possibly introduced. The transport critical current density (J sub c sub t) at 4.2 K increased about twice by the 5 mol% addition and reached 15 and 5 kA cm sup - sup 2 at 8 and 10 T, respectively.

Preparation of c-axis perpendicularly oriented ultra-thin L10-FePt films on MgO and VN underlayers

Science.gov (United States)

Futamoto, Masaaki; Shimizu, Tomoki; Ohtake, Mitsuru

2018-05-01

Ultra-thin L10-FePt films of 2 nm average thickness are prepared on (001) oriented MgO and VN underlayers epitaxially grown on base substrate of SrTiO3(001) single crystal. Detailed cross-sectional structures are observed by high-resolution transmission electron microscopy. Continuous L10-FePt(001) thin films with very flat surface are prepared on VN(001) underlayer whereas the films prepared on MgO(001) underlayer consist of isolated L10-FePt(001) crystal islands. Presence of misfit dislocation and lattice bending in L10-FePt material is reducing the effective lattice mismatch with respect to the underlayer to be less than 0.5 %. Formation of very flat and continuous FePt layer on VN underlayer is due to the large surface energy of VN material where de-wetting of FePt material at high temperature annealing process is suppressed under a force balance between the surface and interface energies of FePt and VN materials. An employment of underlayer or substrate material with the lattice constant and the surface energy larger than those of L10-FePt is important for the preparation of very thin FePt epitaxial thin continuous film with the c-axis controlled to be perpendicular to the substrate surface.

Optimization of the copper addition to the core of in situ Cu-sheathed MgB2 wires

International Nuclear Information System (INIS)

Woźniak, M; Juda, K L; Hopkins, S C; Glowacki, B A; Gajda, D

2013-01-01

Recent results on powder-in-tube in situ Cu-sheathed MgB 2 wires have shown that copper powder additions to the core can accelerate the formation of MgB 2 , increasing its volume fraction and greatly decreasing the amount of Mg–Cu intermetallic phases present in the core after heat treatment. The amount of added copper and heat treatment conditions strongly affect the critical current of the wire and require optimization. To identify the optimum parameters, eight wires with starting core compositions of Mg+2B+xCu with x = 0, 0.01, 0.03, 0.05, 0.07, 0.09, 0.12 and 0.15 were prepared with two heating ramp rates and their properties were investigated by SEM, XRD and J c and n-value measurements. The highest J c was found to be for x = 0.09, whereas x = 0.03 resulted in the highest n-value. The results are relatively independent of the heating ramp rate used for heat treatment. (paper)

A comparative study of the adsorption and oxidation of L-alanine and L-serine on Au(1 0 0), Au(1 1 1) and gold thin film electrodes in acid media

International Nuclear Information System (INIS)

Sandoval, Andrea P.; Orts, José Manuel; Rodes, Antonio; Feliu, Juan M.

2013-01-01

The adsorption and oxidation of L-alanine and L-serine at Au(1 1 1) and Au(1 0 0) single crystal and evaporated thin-film electrodes with preferential (1 1 1) orientation was studied in perchloric acid solutions. For this purpose, cyclic voltammetry experiments were combined with external reflection infrared spectroscopy (gold single crystals) and surface-enhanced infrared reflection–absorption spectroscopy under attenuated total reflection conditions (ATR-SEIRAS) (gold thin films). In addition, theoretical harmonic vibrational frequencies, obtained from B3LYP/LANL2DZ, 6-31+G(d) calculations for the zwitterionic species adsorbed on Au clusters with (1 1 1) orientation, were used to interpret the experimental spectra. The optimized geometry obtained from DFT calculations for the corresponding zwitterion plus a water molecule, under the application of an external electric field of 0.01 a.u. corresponds to a bidentate asymmetrical bridge adsorption configuration. The absence of an adsorbate band for the asymmetric OCO stretching in the experimental infrared spectra confirms the bidentate bonding of the adsorbed zwitterion through the oxygen atoms of the carboxylate group irrespective of the crystallographic orientation of the electrode surface, the adsorbate coverage and the electrode potential. In addition to typical interfacial water bands associated to perchlorate anions, which are co-adsorbed in order to compensate the positive charge of the ammonium group, the ATR-SEIRA spectra also show bands around 2950 cm −1 that can be related to the formation of hydrogen bonds between interfacial water and the ammonium group of the adsorbed zwitterion. The voltammetric experiments have shown that, as in the case of platinum electrodes, L-serine oxidizes at lower potentials than L-alanine. Under these conditions, the in situ infrared experiments show the formation of carbon dioxide and adsorbed cyanide as oxidation products of L-serine. In the case of L-alanine, only

Improvement of Caper (Capparis spinosa L) propagation using in vitro culture and gamma irradiation

International Nuclear Information System (INIS)

Al-Safadi, B.; Elias, R.

2010-01-01

We studied some of the factors influencing seed germination and shoot growth of caper (Capparis spinosa L) and callus formation and regeneration from different parts of the plant (leaf, shoots, fruits) in order to establish a protocol for propagating this plant on a commercial scale. For the dormant seeds, we studied scratching the seed coat using iron particle filings prior to culture on nutrient medium or peatmos. Scratched and non-scratched seeds were also treated with concentrated sulfuric acid for various periods (20, 30, 45, 60 min). Seeds were additionally treated with ultrasonic waves for different periods (15, 30, 45, 60 min). The seeds were also irradiated with 50, 100, and 150 gray of gamma rays to study the effects of irradiation on the germination of caper seeds. Irradiation of the seed with 100 gray dose led to 50% germination one month after culturing in vitro, whereas, no seeds germinated in the control. Irradiation with 150 gray dose led to 18% germination of the seed. As for irradiated seed cultured in the peatmos, 70% of the seed germinated at the 100 gray dose whereas, only 5% of the seed germinated in the control. Treatment of the seed with H sub 2 SO sub 4 for 20 mints with scratching was very effective in stimulating germination, where the percentage of germinated seed reached 46% compared with 0% in the control. Treatment with just H sub 2 SO sub 4 for 20 mints resulted in 32% seed germination and treatment with just scratching resulted in only 20% germination. On the other hand, treating the seed with ultrasonic waves did not result in any seed germination. The effect of irradiation was also studied on the growth of caper shoots in vitro. The shoots were irradiated with 10, 15, and 20 gray and subsequently cultured on the MS medium without any growth regulators. The 10 gray dose stimulated shoot growth where average leaf area increased from 1.1 to 2.4 cm sup 2. The same irradiation dose, also, led to an increase in shoot length from 1.5 to

Improvement of Caper (Capparis spinosa L) propagation using in vitro culture and gamma irradiation

International Nuclear Information System (INIS)

Al-Safadi, B.; Elias, R.

2009-05-01

We studied some of the factors influencing seed germination and shoot growth of caper (Capparis spinosa L) and callus formation and regeneration from different parts of the plant (leaf, shoots, fruits) in order to establish a protocol for propagating this plant on a commercial scale. For the dormant seeds, we studied scratching the seed coat using iron particle filings prior to culture on nutrient medium or peatmos. Scratched and non-scratched seeds were also treated with concentrated sulfuric acid for various periods (20, 30, 45, 60 min). Seeds were additionally treated with ultrasonic waves for different periods (15, 30, 45, 60 min). The seeds were also irradiated with 50, 100, and 150 gray of gamma rays to study the effects of irradiation on the germination of caper seeds. Irradiation of the seed with 100 gray dose led to 50% germination one month after culturing in vitro, whereas, no seeds germinated in the control. Irradiation with 150 gray dose led to 18% germination of the seed. As for irradiated seed cultured in the peatmos, 70% of the seed germinated at the 100 gray dose whereas, only 5% of the seed germinated in the control. Treatment of the seed with H 2 SO 4 for 20 mints with scratching was very effective in stimulating germination, where the percentage of germinated seed reached 46% compared with 0% in the control. Treatment with just H 2 SO 4 for 20 mints resulted in 32% seed germination and treatment with just scratching resulted in only 20% germination. On the other hand, treating the seed with ultrasonic waves did not result in any seed germination. The effect of irradiation was also studied on the growth of caper shoots in vitro. The shoots were irradiated with 10, 15, and 20 gray and subsequently cultured on the MS medium without any growth regulators. The 10 gray dose stimulated shoot growth where average leaf area increased from 1.1 to 2.4 cm 2 . The same irradiation dose, also, led to an increase in shoot length from 1.5 to 2.2 cm. This was

Formation of aluminum titanate with small additions of MgO and SiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Guedes-Silva, Cecilia Chaves; Ferreira, Thiago dos Santos; Genova, Luis Antonio [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Carvalho, Flavio Machado de Souza, E-mail: cecilia.guedes@ipen.br [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Instituto de Geociencias

2016-03-15

The formation of aluminum titanate was investigated by isothermal treatments of samples obtained from equimolar mixtures of alumina and titania, containing small amounts of silica and magnesia. Results of differential thermal analysis and Rietveld refinements of data collected by X-ray powder diffraction (XRPD) showed that additions of silica in amounts used in this work did not influence the formation of aluminum titanate. However, the presence of magnesia favored the formation of aluminum titanate in two steps, first one by incorporating Mg{sup 2+} into Al{sub 2}TiO{sub 5} lattice during its initial formation, and the second one by accelerating the Al{sub 2}TiO{sub 5} formation, contributing to large quantities of this phase. MgO doped samples have also developed a more suitable microstructure for stabilizing of Al{sub 2}TiO{sub 5}, what make them promising for applications such as thermal barriers, internal combustion engines and support material for catalyst. (author)

Anaerobic digestion of swine manure under natural zeolite addition: VFA evolution, cation variation, and related microbial diversity.

Science.gov (United States)

Lin, Lin; Wan, Chunli; Liu, Xiang; Lei, Zhongfang; Lee, Duu-Jong; Zhang, Yi; Tay, Joo Hwa; Zhang, Zhenya

2013-12-01

Batch experiments were carried out on anaerobic digestion of swine manure under 10 % of total solids and 60 g/L of zeolite addition at 35 °C. Four distinctive volatile fatty acid (VFAs) evolution stages were observed during the anaerobic process, i.e., VFA accumulation, acetic acid (HAc) and butyric acid (HBu) utilization, propionic acid (HPr) and valeric acid (HVa) degradation, and VFA depletion. Large decreases in HAc/HBu and HPr/HVa occurred respectively at the first and second biogas peaks. Biogas yield increased by 20 % after zeolite addition, about 356 mL/g VSadded with accelerated soluble chemical oxygen demand degradation and VFA (especially HPr and HBu) consumption in addition to a shortened lag phase between the two biogas peaks. Compared with Ca(2+) and Mg(2+) (100-300 mg/L) released from zeolite, simultaneous K(+) and NH4 (+) (580-600 mg/L) adsorptions onto zeolite particles contributed more to the enhanced biogasification, resulting in alleviated inhibition effects of ammonium on acidogenesis and methanogenesis, respectively. All the identified anaerobes could be grouped into Bacteroidetes and Firmicutes, and zeolite addition had no significant influence on the microbial biodiversity in this study.

Microstructure and Corrosion Resistance of Laser Additively Manufactured 316L Stainless Steel

Science.gov (United States)

Trelewicz, Jason R.; Halada, Gary P.; Donaldson, Olivia K.; Manogharan, Guha

2016-03-01

Additive manufacturing (AM) of metal alloys to produce complex part designs via powder bed fusion methods such as laser melting promises to be a transformative technology for advanced materials processing. However, effective implementation of AM processes requires a clear understanding of the processing-structure-properties-performance relationships in fabricated components. In this study, we report on the formation of micro and nanoscale structures in 316L stainless steel samples printed by laser AM and their implications for general corrosion resistance. A variety of techniques including x-ray diffraction, optical, scanning and transmission electron microscopy, x-ray fluorescence, and energy dispersive x-ray spectroscopy were employed to characterize the microstructure and chemistry of the laser additively manufactured 316L stainless steel, which are compared with wrought 316L coupons via electrochemical polarization. Apparent segregation of Mo has been found to contribute to a loss of passivity and an increased anodic current density. While porosity will also likely impact the environmental performance (e.g., facilitating crevice corrosion) of AM alloys, this work demonstrates the critical influence of microstructure and heterogeneous solute distributions on the corrosion resistance of laser additively manufactured 316L stainless steel.

Effects of Cu or Ag additions on the kinetics of MgB₂ phase formation in Fe-sheated wires

DEFF Research Database (Denmark)

Grivel, Jean-Claude; Abrahamsen, Asger Bech; Bednarcik, J.

2008-01-01

MgB2/Fe wires have been produced by the powder-in-tube technique following the in situ route. The influence of low amounts of Cu or Ag additions into the precursor powder mixture on the kinetics of MgB2 formation was studied in situ by means of synchrotron x-ray diffraction during heat-treatments...

Influence of cytokinins, auxins and polyamines on in vitro mass multiplication of cotton (Gossypium hirsutum L. cv. SVPR2).

Science.gov (United States)

Ganesan, M; Jayabalan, N

2006-06-01

In the present investigation, the influence of different forms of cytokinins, auxins and polyamines were tested for mass multiplication and regeneration of cotton. Initially, for the identification of effective concentration for multiple shoot induction, various concentrations of BAP, Kin and 2iP along with IAA and NAA were tested. Among tested concentrations, media fortified with MS salts; B5 vitamins; 30 g/l, glucose; 2.0 mg/l, 2iP; 2.0 mg/l, IAA and 0.7 % agar showed best response for multiplication of shoot tip explants (20 shoots per shoot tip explants). In nodal explants, maximum of 18.6 shoots were obtained in the media fortified with MS salts, B5 vitamins, 30 g/l, glucose, 2.0 mg/l, 2iP, 1.0 mg/l, NAA and 0.7 % agar. Effect of different concentrations of polyamines like spermidine and putrescine were also tested along with the above said multiplication media. Among the various treatments, 20 mg/l of putrescine showed best response and the multiple of shoots were increased to 26.5 shoots per shoot tip explants and 24.5 shoots per nodal explants. Elongation of shoots was achieved on multiple shoot induction medium. Significant number of roots were initiated in the medium supplemented with MS salts, vitamin B5 and IBA (2.0 mg/l). The frequency of root induction was increased by addition of, PVP (10 mg/l) along with root induction medium and after 2 weeks, the roots reached the maximum length of 22 cm. Further, these plantlets were hardened by using sand, soil and vermiculate in 1:1:1 ratio. The hardened plants were transferred to the environmental growth chamber for proper acclimatization. The hardened plants were then transferred to field for boll yielding and they exhibited 100% survival.

Evaluation of antioxidant and cytoprotective activities of Arnica montana L. and Artemisia absinthium L. ethanolic extracts

Directory of Open Access Journals (Sweden)

Craciunescu Oana

2012-09-01

Full Text Available Abstract Background Arnica montana L. and Artemisia absinthium L. (Asteraceae are medicinal plants native to temperate regions of Europe, including Romania, traditionally used for treatment of skin wounds, bruises and contusions. In the present study, A. montana and A. absinthium ethanolic extracts were evaluated for their chemical composition, antioxidant activity and protective effect against H2O2-induced oxidative stress in a mouse fibroblast-like NCTC cell line. Results A. absinthium extract showed a higher antioxidant capacity than A. montana extract as Trolox equivalent antioxidant capacity, Oxygen radical absorbance capacity and 2,2-diphenyl-1-picrylhydrazyl free radical-scavenging activity, in correlation with its flavonoids and phenolic acids content. Both plant extracts had significant effects on the growth of NCTC cells in the range of 10–100 mg/L A. montana and 10–500 mg/L A. absinthium. They also protected fibroblast cells against hydrogen peroxide-induced oxidative damage, at the same doses. The best protection was observed in cell pre-treatment with 10 mg/L A. montana and 10–300 mg/L A. absinthium, respectively, as determined by Neutral red and lactate dehydrogenase assays. In addition, cell pre-treatment with plant extracts, at these concentrations, prevented morphological changes induced by hydrogen peroxide. Flow-cytometry analysis showed that pre-treatment with A. montana and A. absinthium extracts restored the proportion of cells in each phase of the cell cycle. Conclusions A. montana and A. absinthium extracts, rich in flavonoids and phenolic acids, showed a good antioxidant activity and cytoprotective effect against oxidative damage in fibroblast-like cells. These results provide scientific support for the traditional use of A. montana and A. absinthium in treatment of skin disorders.

rno-miR-665 targets BCL2L1 (Bcl-xl) and increases vulnerability to propofol in developing astrocytes.

Science.gov (United States)

Sun, Wen-Chong; Pei, Ling

2016-07-01

Propofol exerts a cytotoxic influence over immature neurocytes. Our previous study revealed that clinically relevant doses of propofol accelerated apoptosis of primary cultured astrocytes of developing rodent brains via rno-miR-665 regulation. However, the role of rno-miR-665 during the growth spurt of neonatal rodent brains in vivo is still uncertain. Post-natal day 7 (P7) rats received a single injection of propofol 30 mg/kg intraperitoneally (i.p.), and neuroapoptosis of hippocampal astrocytes was analyzed by immunofluorescence and scanning electron microscopy. The differential expression of rno-miR-665, BCL2L1 (Bcl-xl), and cleaved caspase 3 (CC3) was surveyed by qRT-PCR and western blotting. In addition, the utility of A-1155463, a highly potent and BCL2L1-selective antagonist, was aimed to assess the contribution of BCL2L1 for neuroglial survival. Following the intraventricular injection of lentivirus rno-miR-665, neuroprotection was detected by 5-point scale measurement. The single dose of propofol 30 mg/kg triggered dose-dependent apoptosis of developing hippocampal astrocytes. Meanwhile, propofol triggered both rno-miR-665 and CC3, and depressed BCL2L1, which was predicted as one target gene of rno-miR-665. Combination treatment with A-1155463 and propofol induced lower mRNA and protein levels of BCL2L1 and more CC3 activation than propofol treatment alone in vivo. The lentivirus-mediated knockdown of rno-miR-665 elevated BCL2L1 and attenuated CC3 levels, whereas up-regulation of rno-miR-665 suppressed BCL2L1 and induced CC3 expression in vivo. More importantly, rno-miR-665 antagomir infusion improved neurological outcomes of pups receiving propofol during the brain growth spurt. Rno-miR-665, providing a potential target for alternative therapeutics for pediatric anesthesia, is susceptible to propofol by negatively targeting antiapoptotic BCL2L1. Relatively little is known about the association between exposure of astrocytes to brief propofol

A Novel Combination of Surfactant Addition and Persulfate-assisted Electrokinetic Oxidation for Remediation of Pyrene-Contaminated Soil

Directory of Open Access Journals (Sweden)

M. Abtahi

2018-03-01

Full Text Available Effect of surfactant addition on persulfate-assisted electrokinetic remediation of pyrene-spiked soil was studied. The influence of effective factors including voltage, surfactant addition, moisture content, and persulfate concentration on the removal of initial pyrene concentration of 200 mg kg–1 were investigated. A complete pyrene removal was observed for voltage of 1 V cm–1, saturated conditions, Tween 80 concentration of 20 mL kg–1, and persulfate concentration of 100 mg kg–1 after 24 h, corresponding to pyrene mineralization of 61 %, based on TPH analysis. The experimental results were best fitted with pseudo-first-order kinetic model with correlation coefficient of 0.968 and rate constant of 0.191 min−1. The main intermediates of pyrene degradation were benzene o-toluic acid, acetic, azulene, naphthalene and decanoic acid. Finally, an unwashed hydrocarbon-contaminated soil was subjected to persulfate-assisted electrokinetic remediation, and a TPH removal of 38 % was observed for the initial TPH content of 912 mg kg–1, under the selected conditions.

Post-Hartree-Fock studies of the He/Mg(0001) interaction: Anti-corrugation, screening, and pairwise additivity

Energy Technology Data Exchange (ETDEWEB)

Lara-Castells, María Pilar de, E-mail: Pilar.deLara.Castells@csic.es [Instituto de Física Fundamental (CSIC), Serrano 123, E-28006 Madrid (Spain); Fernández-Perea, Ricardo [Instituto de Estructura de la Materia (CSIC), Serrano 123, E-28006 Madrid (Spain); Madzharova, Fani; Voloshina, Elena, E-mail: elena.voloshina@hu-berlin.de [Humboldt-Universität zu Berlin, Institut für Chemie, Unter den Linden 6, 10099 Berlin (Germany)

2016-06-28

The adsorption of noble gases on metallic surfaces represents a paradigmatic case of van-der-Waals (vdW) interaction due to the role of screening effects on the corrugation of the interaction potential [J. L. F. Da Silva et al., Phys. Rev. Lett. 90, 066104 (2003)]. The extremely small adsorption energy of He atoms on the Mg(0001) surface (below 3 meV) and the delocalized nature and mobility of the surface electrons make the He/Mg(0001) system particularly challenging, even for state-of-the-art vdW-corrected density functional-based (vdW-DFT) approaches [M. P. de Lara-Castells et al., J. Chem. Phys. 143, 194701 (2015)]. In this work, we meet this challenge by applying two different procedures. First, the dispersion-corrected second-order Möller-Plesset perturbation theory (MP2C) approach is adopted, using bare metal clusters of increasing size. Second, the method of increments [H. Stoll, J. Chem. Phys. 97, 8449 (1992)] is applied at coupled cluster singles and doubles and perturbative triples level, using embedded cluster models of the metal surface. Both approaches provide clear evidences of the anti-corrugation of the interaction potential: the He atom prefers on-top sites, instead of the expected hollow sites. This is interpreted as a signature of the screening of the He atom by the metal for the on-top configuration. The strong screening in the metal is clearly reflected in the relative contribution of successively deeper surface layers to the main dispersion contribution. Aimed to assist future dynamical simulations, a pairwise potential model for the He/surface interaction as a sum of effective He–Mg pair potentials is also presented, as an improvement of the approximation using isolated He–Mg pairs.

Effects of bioaugmentation on enhanced reductive dechlorination of 1,1,1-trichloroethane in groundwater - a comparison of three sites

DEFF Research Database (Denmark)

Scheutz, Charlotte; Durant, Neal D.; Broholm, Mette Martina

2014-01-01

, microcosms were amended with various concentrations of chloroethanes (TCA or monochloroethane [CA]) and/or chloroethenes (tetrachloroethene [PCE], trichloroethene [TCE], or 1,1-dichloroethene [1,1-DCE]). Results showed that combined electron donor addition and bioaugmentation stimulated dechlorination of TCA...... and 1,1-dichloroethane (1,1-DCA) to CA, and dechlorination of PCE, TCE, 1,1-DCE and cDCE to ethane. Dechlorination of CA was not observed. Bioaugmentation improved the rate and extent of TCA and 1,1-DCA dechlorination at two sites, but did not accelerate dechlorination at a third site where geochemical...... conditions were reducing and Dhc and Dhb were indigenous. TCA at initial concentrations of 5 mg/L inhibited (i.e., slowed the rate of) TCA dechlorination, TCE dechlorination, donor fermentation, and methanogenesis. 1 mg/L TCA did not inhibit dechlorination of TCA, TCE or cDCE. Moreover, complete...

Different effects of a novel CaO-MgO-SiO₂-based multiphase glass-ceramic on cell behaviors of normal and cancer cells in vitro.

Science.gov (United States)

Zhang, Mengjiao; Chen, Xianchun; Pu, Ximing; Liao, Xiaoming; Huang, Zhongbing; Yin, Guangfu

2014-04-01

The effects in vitro of a novel multiphase glass-ceramic (with nominal composition of 43.19% CaO, 7.68% MgO, and 49.13% SiO2 in weight percent) on cell adhesion, proliferation, differentiation and ultrastructure of human osteosarcoma cell line MG63, mouse fibroblasts L929, and human lung adenocarcinoma epithelial cell line A549 were investigated in this research. Scanning electron microscopy (SEM) micrographs revealed that the surface morphology of this glass-ceramic was beneficial to cell adhesion. The glass-ceramic extracts at certain concentrations could stimulate the proliferation and differentiation of MG63 and L929 cells, whereas inhibit A549 proliferation, which might be resulted from the released Si ions. In addition, when cultured with 0.1mg/mL glass-ceramic powder suspension, the cell ultrastructure of MG63 showed abundant organelles and L929 displayed the phenomena of cellular stress response. While more interestingly, A549 exhibited chromatin condensation, mitochondria swell and RER expansion, which was presumed to be early signs of apoptosis. These results suggest that this novel CaO-MgO-SiO2-based multiphase glass-ceramic has potential for bone regeneration and tissue engineering applications. Copyright © 2013 Elsevier B.V. All rights reserved.

Mg2+ improves the thermotolerance of probiotic Lactobacillus rhamnosus GG, Lactobacillus casei Zhang and Lactobacillus plantarum P-8.

Science.gov (United States)

Yang, Y; Huang, S; Wang, J; Jan, G; Jeantet, R; Chen, X D

2017-04-01

Food-related carbohydrates and proteins are often used as thermoprotectants for probiotic lactobacilli during industrial production and processing. However, the effect of inorganic salts is rarely reported. Magnesium is the second-most abundant cation in bacteria, and commonly found in various foods. Mg 2+ homeostasis is important in Salmonella and has been reported to play a critical role in their thermotolerance. However, the role of Mg 2+ in thermotolerance of other bacteria, in particular probiotic bacteria, still remains a hypothesis. In this study, the effect of Mg 2+ on thermotolerance of probiotic lactobacilli was investigated in three well-documented probiotic strains, Lactobacillus rhamnosus GG, Lactobacillus casei Zhang and Lactobacillus plantarum P-8, in comparison with Zn 2+ and Na + . Concentrations of Mg 2+ between 10 and 50 mmol l -1 were found to increase the bacterial survival upon heat challenge. Remarkably, Mg 2+ addition at 20 mmol l -1 led to a 100-fold higher survival of L. rhamnosus GG upon heat challenge. This preliminary study also showed that Mg 2+ shortened the heat-induced extended lag time of bacteria, which indicated the improvement in bacterial recovery from thermal injury. In order to improve the productivity and stability of live probiotics, extensive investigations have been carried out to improve thermotolerance of probiotics. However, most of these studies focused on the effects of carbohydrates, proteins or amino acids. The roles of inorganic salts in various food materials, which have rarely been reported, should be considered when incorporating probiotics into these foods. In this study, Mg 2+ was found to play a significant role in the thermotolerance of probiotic lactobacilli. A novel strategy may be available in the near future by employing magnesium salts as protective agents of probiotics during manufacturing process. © 2017 The Society for Applied Microbiology.

Propagação vegetativa de jambeiro vermelho [Syzygium malaccense (L. Merr. & L.M. Perry] Vegetative propagation of malay apple [Syzygium malaccense (L. Merr. & L.M. Perry

Directory of Open Access Journals (Sweden)

Eduardo José de Almeida

2010-12-01

Full Text Available O jambeiro vermelho [Syzygium malaccense (L. Merr. & L.M. Perry] se apresenta como opção ao fruticultor por apresentar frutos atrativos e bem aceitos pelo consumidor. A dificuldade de cultivo dessa espécie reside no fato de que a planta possui um porte demasiadamente alto e longo período juvenil quando propagada por semente, com isso, é desejável sua multiplicação vegetativa visando a antecipar o período produtivo e diminuir seu porte. Foi estudada a possibilidade de clonagem dessa espécie pelas técnicas de estaquia, alporquia e enxertia. No experimento por estaquia, testaram-se três doses de ácido indolbutírico (AIB (0, 1.000 3.000 e 5.000 mg L-1 em dois comprimentos de estacas herbáceas (15 e 25 cm. No experimento de alporquia, avaliaram-se duas épocas de realização do alporque (verão e outono e quatro doses de AIB (0, 1.000, 4.000, 7.000 e 10.000 mg kg-1. Na enxertia, analisou-se a compatibilidade do jambeiro vermelho (S. malaccense sobre o jambeiro rosa [Syzygium jambos (L. Alston] com dois diâmetros de porta-enxertos (0,5 e 0,8 cm em duas épocas (inverno e verão, pelo método de enxertia de topo em fenda cheia. A estaquia obteve até 20% de enraizamento, independentemente da dose de AIB, exceto na dose de 5.000 mg L-1, que apresentou efeito negativo ao enraizamento entre estacas de 15 cm; não houve sucesso para alporquia e enxertia, nas condições estudadas.The Malay Apple [Syzygium malaccense (L. Merr. & L.M. Perry] is an option for the producer as its fruits are attractive and well accepted by the consumer. The difficulty of culture of this species is that the plant is very tall and has a long juvenile period when propagated by seed, making its vegetative propagation necessary to anticipate the productive period and decrease its size. The possibility of vegetative propagation of this species was studied by cutting, layering, and grafting. In the cutting experiment, three doses of indolbutyric acid (IBA (0, 1,000, 3

Transport and activation of S-(1,2-dichlorovinyl)-L-cysteine and N-acetyl-S-(1,2-dichlorovinyl)-L-cysteine in rat kidney proximal tubules

International Nuclear Information System (INIS)

Zhang, G.H.; Stevens, J.L.

1989-01-01

An important step in understanding the mechanism underlying the tubular specificity of the nephrotoxicity of toxic cysteine conjugates is to identify the rate-limiting steps in their activation. The rate-limiting steps in the activation of toxic cysteine conjugates were characterized using isolated proximal tubules from the rat and 35S-labeled S-(1,2-dichlorovinyl)-L-cysteine (DCVC) and N-acetyl-S-(1,2-dichlorovinyl)-L-cysteine (NAC-DCVC) as model compounds. The accumulation by tubules of 35S radiolabel from both DCVC and NAC-DCVC was time and temperature dependent and was mediated by both Na+-dependent and independent processes. Kinetic studies with DCVC in the presence of sodium revealed the presence of two components with apparent Km and Vmax values of (1) 46 microM and 0.21 nmol/mg min and (2) 2080 microM and 7.3 nmol/mg.min. NAC-DVVC uptake was via a single system with apparent Km and Vmax values of 157 microM and 0.65 nmol/mg.min, respectively. Probenecid, an inhibitor of the renal organic anion transport system, inhibited accumulation of radiolabel from NAC-DCVC, but not from DCVC. The covalent binding of 35S label to cellular macromolecules was much greater from [35S]DCVC than from NAC-[35S]DCVC. Analysis of metabolites showed that a substantial amount of the cellular NAC-[35S]DCVC was unmetabolized while [35S]DCVC was rapidly metabolized to bound 35S-labeled material and unidentified products. The data suggest that DCVC is rapidly metabolized following transport, but that activation of NAC-DCVC depends on a slower rate of deacetylation. The results are discussed with regard to the segment specificity of cysteine conjugate toxicity and the role of disposition in vivo in the nephrotoxicity of glutathione conjugates

Application of 1-hydroxyethylidene-1, 1-diphosphonic acid in boiler water for industrial boilers.

Science.gov (United States)

Zeng, Bin; Li, Mao-Dong; Zhu, Zhi-Ping; Zhao, Jun-Ming; Zhang, Hui

2013-01-01

The primary method used for boiler water treatment is the addition of chemicals to industrial boilers to prevent corrosion and scaling. The static scale inhibition method was used to evaluate the scale inhibition performance of 1-hydroxyethylidene-1, 1-diphosphonic acid (HEDP). Autoclave static experiments were used to study the corrosion inhibition properties of the main material for industrial boilers (20# carbon steel) with an HEDP additive in the industrial boiler water medium. The electrochemical behavior of HEDP on carbon steel corrosion control was investigated using electrochemical impedance spectroscopy and Tafel polarization techniques. Experimental results indicate that HEDP can have a good scale inhibition effect when added at a quantity of 5 to 7 mg/L at a test temperature of not more than 100 °C. To achieve a high scale inhibition rate, the HEDP dosage must be increased when the test temperature exceeds 100 °C. Electrochemical and autoclave static experimental results suggest that HEDP has a good corrosion inhibition effect on 20# carbon steel at a concentration of 25 mg/L. HEDP is an excellent water treatment agent.

The effects of Mg addition on the microstructure and mechanical properties of thixoformed Al–5%Si–Cu alloys

International Nuclear Information System (INIS)

Salleh, M.S.; Omar, M.Z.; Syarif, J.

2015-01-01

Highlights: • The average globule size of α-Al decreased when Mg amount is increased. • T6 heat treatment has increased the strength of the thixoformed alloys. • The elongation after T6 heat treatment is even significantly improved. • Thixoformed alloy with high Mg content shows a brittle type fracture. • Thixoformed alloy in T6 condition shows a ductile type fracture. - Abstract: In this study, the effects of different amounts of magnesium (Mg) on the microstructures and tensile properties of thixoformed Al–5%Si–Cu alloys were investigated. Three different alloys containing various amounts of Mg (0.5, 0.8 and 1.2 wt%) were prepared through the cooling slope casting technique, before they were thixoformed using a compression press. Several of the thixoformed samples were then treated with a T6 heat treatment, that is, solution treatment at 525 °C for 8 h, quenching in warm water at 60 °C, followed by aging at 155 °C for 4 h. All of the samples were then characterised by optical microscopy (OM), scanning electron microscopy (SEM) energy dispersive X-ray (EDX) spectroscopy and X-ray diffraction (XRD) analysis as well as by tensile tests. The results revealed that magnesium was able to refine the size of α-Al globules and the eutectic silicon in the samples. It was also observed that a compact π-Al 9 FeMg 3 Si 5 phase was formed when the magnesium content was 0.8 wt% and 1.2 wt%. The mechanical properties of the thixoformed alloys improved significantly after the T6 heat treatment. The highest attainment was recorded by the latter alloy (i.e. with 1.2 wt%Mg) with its ultimate tensile strength (UTS) as high as 306 MPa, yield strength (YS), 264 MPa, and elongation to fracture of 1.8%. The fracture of thixoformed alloy with a low Mg content (0.5 wt%) showed a combination of dimple and cleavage fracture, whereas in the alloy that contained the highest Mg content (1.2 wt%), cleavage fracture was observed

Microstructure and properties of Mg-Al binary alloys

Directory of Open Access Journals (Sweden)

ZHENG Wei-chao

2006-11-01

Full Text Available The effects of different amounts of added Al, ranging from 1 % to 9 %, on the microstructure and properties of Mg-Al binary alloys were investigated. The results showed that when the amount of added Al is less than 5%, the grain size of the Mg-Al binary alloys decreases dramatically from 3 097 μm to 151 μm with increasing addition of Al. Further addition of Al up to 9% makes the grain size decrease slowly to 111 μm. The α-Mg dendrite arms are also refined. Increasing the amount of added Al decreases the hot cracking susceptibility of the Mg-Al binary alloys remarkably, and enhances the micro-hardness of the α-Mg matrix.

MgB2 and Mg1-xAlxB2 single crystals: high pressure growth and physical properties

International Nuclear Information System (INIS)

Karpinski, J.; Kazakov, S.M.; Jun, J.; Zhigadlo, N.D.; Angst, M.; Puzniak, R.; Wisniewski, A.

2004-01-01

Single crystals of MgB 2 have been grown with a high pressure cubic anvil technique. They grow via the peritectic decomposition of the MgNB 9 ternary nitride. The crystals are of a size up to 2 x 1 x 0.1 mm 3 with a weight up to 230 μg. Typically they have transition temperatures between 38 and 38.6 K with a width of 0.3-0.5 K. Investigations of the P-T phase diagram prove that the MgB 2 phase is stable at least up to 2190 deg. C at high hydrostatic pressure in the presence of Mg vapor under high pressure. Substitution of aluminum for magnesium in single crystals leads to stepwise decrease of T c . This indicates a possible appearance of superstructures or phases with different T c 's. The upper critical field decreases with Al doping

Hemp ( Cannabis sativa L.) seed oil: analytical and phytochemical characterization of the unsaponifiable fraction.

Science.gov (United States)

Montserrat-de la Paz, S; Marín-Aguilar, F; García-Giménez, M D; Fernández-Arche, M A

2014-02-05

Non-drug varieties of Cannabis sativa L., collectively namely as "hemp", have been an interesting source of food, fiber, and medicine for thousands of years. The ever-increasing demand for vegetables oils has made it essential to characterize additional vegetable oil through innovative uses of its components. The lipid profile showed that linoleic (55%), α-linolenic (16%), and oleic (11%) were the most abundant fatty acids. A yield (1.84-1.92%) of unsaponifiable matter was obtained, and the most interesting compounds were β-sitosterol (1905.00 ± 59.27 mg/kg of oil), campesterol (505.69 ± 32.04 mg/kg of oil), phytol (167.59 ± 1.81 mg/kg of oil), cycloartenol (90.55 ± 3.44 mg/kg of oil), and γ-tocopherol (73.38 ± 2.86 mg/100 g of oil). This study is an interesting contribution for C. sativa L. consideration as a source of bioactive compounds contributing to novel research applications for hemp seed oil in the pharmaceutical, cosmetic food, and other non-food industries.

Monoclonal Antibody L1Mab-13 Detected Human PD-L1 in Lung Cancers.

Science.gov (United States)

Yamada, Shinji; Itai, Shunsuke; Nakamura, Takuro; Yanaka, Miyuki; Chang, Yao-Wen; Suzuki, Hiroyoshi; Kaneko, Mika K; Kato, Yukinari

2018-04-01

Programmed cell death ligand-1 (PD-L1) is a type I transmembrane glycoprotein expressed on antigen-presenting cells. It is also expressed in several tumor cells such as melanoma and lung cancer cells. A strong correlation has been reported between human PD-L1 (hPD-L1) expression in tumor cells and negative prognosis in cancer patients. Here, a novel anti-hPD-L1 monoclonal antibody (mAb) L 1 Mab-13 (IgG 1 , kappa) was produced using a cell-based immunization and screening (CBIS) method. We investigated hPD-L1 expression in lung cancer using flow cytometry, Western blot, and immunohistochemical analyses. L 1 Mab-13 specifically reacted hPD-L1 of hPD-L1-overexpressed Chinese hamster ovary (CHO)-K1 cells and endogenous hPD-L1 of KMST-6 (human fibroblast) in flow cytometry and Western blot. Furthermore, L 1 Mab-13 reacted with lung cancer cell lines (EBC-1, Lu65, and Lu99) in flow cytometry and stained lung cancer tissues in a membrane-staining pattern in immunohistochemical analysis. These results indicate that a novel anti-hPD-L1 mAb, L 1 Mab-13, is very useful for detecting hPD-L1 of lung cancers in flow cytometry, Western blot, and immunohistochemical analyses.

Study of agronomic characteristics and advantage indices in intercropping of additive series of Chickpea (Cicer arietinum L. and Black Cumin (Nigella sativa L.

Directory of Open Access Journals (Sweden)

esmaeil rezaei-chiyaneh

2015-12-01

Full Text Available Study of agronomic characteristics and advantage indices in intercropping of additive series of Chickpea (Cicer arietinum L. and Black Cumin (Nigella sativa L. Abstract In order to evaluate quantitive and qualitive yield of Chickpea (Cicer arietinum L. and Black Cumin (Nigella sativa L. in intercropping of additive series, a field experiment was arranged in a randomized complete block design with three replications in West Azerbaijan province- city Nagadeh, Iran during growing reason of 2012-2013. Treatments included 100% Black Cumin + 10% Chickpea, 100% Black Cumin + 20% Chickpea, 100% Black Cumin + 30% Chickpea, 100% Black Cumin + 40% Chickpea and 100% Black Cumin + 50% Chickpea and sole cropping of Chickpea and Black Cumin. Different Planting Ratio had significant effect on studied traits of Chickpea and Black Cumin (exception Essential oil yield of Black Cumin. Yield and components yield in monoculture of each crop was more than other treatments. The highest grain yield and biological yield of chickpea were achieved in monoculture with 1105 and 14479 kg.ha-1, respectively. The results showed that the maximum seed yield and biological yield of Black Cumin were obtained at monoculture with 750 and 2310 kg.ha-1, respectively. The highest of percentage of grain protein (23% and essential oil percentage (1.47% were related to treatment 100% Black Cumin + 50% Chickpea, respectively. Based on this results, the highest land equivalent ratio (LER=1.74, actual yield loss (AYL=6.45 and intercropping advantage (IA=1.70 were obtained by treatment 100% Black Cumin + 10% Chickpea, respectively. Therefore, it seems that treatment 100% Black Cumin + 10% Chickpea is remarkably effective to increase the economic income and land use efficiency.

Anesthetic efficacy of combinations of 0.5 mol/L mannitol and lidocaine with epinephrine for inferior alveolar nerve blocks in patients with symptomatic irreversible pulpitis.

Science.gov (United States)

Kreimer, Timothy; Kiser, Russell; Reader, Al; Nusstein, John; Drum, Melissa; Beck, Mike

2012-05-01

The purpose of these 2 prospective, randomized, single-blind studies was to determine the anesthetic efficacy of lidocaine with epinephrine compared with a combination lidocaine with epinephrine plus 0.5 mol/L mannitol for inferior alveolar nerve (IAN) blocks in patients experiencing symptomatic irreversible pulpitis. In study one, 55 emergency patients randomly received IAN blocks by using a 3.18-mL formulation containing 63.6 mg of lidocaine with 31.8 μg epinephrine or a 5-mL formulation containing 63.6 mg of lidocaine with 31.8 μg epinephrine (3.18 mL) plus 1.82 mL of 0.5 mol/L mannitol. In study two, 51 emergency patients randomly received IAN blocks by using a 1.9-mL formulation containing 76.4 mg of lidocaine with 36 μg epinephrine or a 3-mL formulation containing 76.4 mg of lidocaine with 36 μg epinephrine (1.9 mL) plus 1.1 mL of 0.5 mol/L mannitol. Endodontic access was begun 15 minutes after the IAN block, and all patients had profound lip numbness. Success was defined as no or mild pain (visual analogue scale recordings) on endodontic access or instrumentation. The 1.9 mL of lidocaine (76.4 mg) with epinephrine plus 0.5 mol/L mannitol had a significantly (P = .04) better success rate of 39% when compared with the lidocaine formulation without mannitol (13% success rate). For mandibular posterior teeth in patients with symptomatic irreversible pulpitis, the addition of 0.5 mol/L mannitol to 1.9 mL of lidocaine (76.4 mg) with epinephrine resulted in a statistically higher success rate. However, the combination lidocaine/mannitol formulation would not result in predictable pulpal anesthesia. Copyright © 2012 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Differential growth and yield by canola (Brassica napus L.) and wheat (Triticum aestivum L.) arising from alterations in chemical properties of sandy soils due to additions of fly ash.

Science.gov (United States)

Yunusa, Isa A M; Manoharan, Veeragathipillai; Harris, Rob; Lawrie, Roy; Pal, Yash; Quiton, Jonathan T; Bell, Richard; Eamus, Derek

2013-03-30

There is a need for field trials on testing agronomic potential of coal fly ash to engender routine use of this technology. Two field trials were undertaken with alkaline and acidic fly ashes supplied at between 3 and 6 Mg ha⁻¹ to acidic soils and sown to wheat and canola at Richmond (Eastern Australia) and to wheat only at Merredin (Western Australia). Ash addition marginally (PAPSIM at Richmond over a 100-year period (1909-2008) predicted yield increases in 52% of years with addition of ash at 3.0 Mg ha⁻¹ compared with 24% of years with addition of ash at 6.0 Mg ha⁻¹. The simulated yield increases did not exceed 40% over the control with addition of 6 Mg ha⁻¹ ash, but was between 40% and 50% with an addition rate of 3 Mg ha⁻¹. We found no evidence of phytotoxicity in either crop in this unusually dry year and there is still a need for further field assessment in years with favourable rainfall to enable development of clear recommendations on fly ash rates for optimum yield benefits. © 2012 Society of Chemical Industry.

Trapped particle confinement studies in L = 2 torsatrons for additional helical coils, radial electric field and finite beta effect

International Nuclear Information System (INIS)

Kato, A.; Nakamura, Y.; Wakatani, M.

1990-07-01

L = 2 torsatrons are studied to improve the high energy trapped particle confinement with additional l = 1 and/or l = 3 helical coils. The winding laws are selected in two ways. One is to realize 'σ - optimization' by the additional helical coils, but this approach loses magnetic well region. The other selection is to produce or deepen the magnetic well by the additional helical coils. L=3 helical coils are usable to this end. In this case the improvement of the trapped particle confinement depends on magnetic axis position. Radial electric field producing sheared rotational motion is also considered to improve the trapped particle confinement in a standard l = 2 torsatron. By excluding cancellation between E x B and ΔB drift motion occurred for the parabolic potential profiles, all deeply trapped particles can be confined in the central region. Degradation of the trapped particle confinement by the Shafranov shift is mitigated by shifting the magnetic axis inside in the vacuum configuration. (author)

Evolution of the two-gap nature revealed in the upper critical field of Mg1-xAlxB2

International Nuclear Information System (INIS)

Kim, Heon-Jung; Lee, Hyun-Sook; Park, Min-Seok; Lee, H.-G.; Jo, Younghun; Jung, Myung-Hwa; Lee, Sung-Ik; Kang, Byeongwon

2007-01-01

The temperature and the angular dependences of the upper critical field [H c2 (T,θ)] of Mg 1-x Al x B 2 single crystals (x=0.12 and 0.21) were studied. The H c2 (T,θ) was found to be well described by the dirty-limit two-gap theory. A quantitative comparison of the data with this theory indicated that Mg 1-x Al x B 2 single crystals preserved the two-gap nature but became dirtier. We also found that as the Al concentration was increased, anisotropic impurity scattering increased, making the σ bands less anisotropic. In addition, these results are compared with those of 10% C-doped MgB 2 single crystals

Effect of selenium application on arsenic uptake in rice (Oryza sativa L.).

Science.gov (United States)

Kaur, Sumandeep; Singh, Dhanwinder; Singh, Kuldip

2017-09-01

Alluvial aquifers of the agrarian state of Punjab of southwestern arid zone used for irrigation of rice crops are rich in arsenic concentration. In the present study, rice (Oryza sativa L.) crops were raised in pots in a greenhouse with a purpose to study whether selenium (Se) application was effective in ameliorating As uptake. The rice crop was irrigated with arsenic laced water (0, 2.5, 5.0, 10.0 μM As L -1 ) throughout the growing period, without and with selenium (0.05 and 0.10 mg kg -1 ) added through mustard biomass, grown ex situ in seleniferous soil. Arsenic uptake and dry matter yield in different parts of the rice crop were assayed after application of As alone and simultaneous supplementations (As + Se). An antagonistic interaction between Se and As was observed. Addition of As through irrigation water significantly reduced yield of rice grain, straw and root. However, subsequent addition of Se helped in mitigating the harmful effect of As and countered the yield reduction caused due to As toxicity. The effect of Se on dry matter yield was more pronounced at its higher dose (0.10 mg kg -1 ) as compared to its lower dose (0.05 mg kg -1 ). The presence of Se either alone or added along with As significantly reduced the As concentration and its uptake by different parts of rice and higher reduction in As concentration was observed with addition of the highest level of applied Se (0.10 mg kg -1 ). Our observations indicated that Se supplementation might be favourable to reduce As accumulation and toxicity in rice crops.

Innovative micro-textured hydroxyapatite and poly(l-lactic)-acid polymer composite film as a flexible, corrosion resistant, biocompatible, and bioactive coating for Mg implants.

Science.gov (United States)

Kim, Sae-Mi; Kang, Min-Ho; Kim, Hyoun-Ee; Lim, Ho-Kyung; Byun, Soo-Hwan; Lee, Jong-Ho; Lee, Sung-Mi

2017-12-01

The utility of a novel ceramic/polymer-composite coating with a micro-textured microstructure that would significantly enhance the functions of biodegradable Mg implants is demonstrated here. To accomplish this, bioactive hydroxyapatite (HA) micro-dots can be created by immersing a Mg implant with a micro-patterned photoresist surface in an aqueous solution containing calcium and phosphate ions. The HA micro-dots can then be surrounded by a flexible poly(l-lactic)-acid (PLLA) polymer using spin coating to form a HA/PLLA micro-textured coating layer. The HA/PLLA micro-textured coating layer showed an excellent corrosion resistance when it was immersed in a simulated body fluid (SBF) solution and good biocompatibility, which was assessed by in vitro cell tests. In addition, the HA/PLLA micro-textured coating layer had high deformation ability, where no apparent changes in the coating layer were observed even after a 5% elongation, which would be unobtainable using HA and PLLA coating layers; furthermore, this allowed the mechanically-strained Mg implant with the HA/PLLA micro-textured coating layer to preserve its excellent corrosion resistance and biocompatibility in vitro. Copyright © 2017 Elsevier B.V. All rights reserved.

Gold nanoparticles functionalized with a fragment of the neural cell adhesion molecule L1 stimulate L1-mediated functions

Science.gov (United States)

Schulz, Florian; Lutz, David; Rusche, Norman; Bastús, Neus G.; Stieben, Martin; Höltig, Michael; Grüner, Florian; Weller, Horst; Schachner, Melitta; Vossmeyer, Tobias; Loers, Gabriele

2013-10-01

sequence of the third fibronectin type III domain of murine L1 was identified and conjugated to gold nanoparticles (AuNPs) to obtain constructs that interact homophilically with the extracellular domain of L1 and trigger the cognate beneficial L1-mediated functions. Covalent conjugation was achieved by reacting mixtures of two cysteine-terminated forms of this L1 peptide and thiolated poly(ethylene) glycol (PEG) ligands (~2.1 kDa) with citrate stabilized AuNPs of two different sizes (~14 and 40 nm in diameter). By varying the ratio of the L1 peptide-PEG mixtures, an optimized layer composition was achieved that resulted in the expected homophilic interaction of the AuNPs. These AuNPs were stable as tested over a time period of 30 days in artificial cerebrospinal fluid and interacted with the extracellular domain of L1 on neurons and Schwann cells, as could be shown by using cells from wild-type and L1-deficient mice. In vitro, the L1-derivatized particles promoted neurite outgrowth and survival of neurons from the central and peripheral nervous system and stimulated Schwann cell process formation and proliferation. These observations raise the hope that, in combination with other therapeutic approaches, L1 peptide-functionalized AuNPs may become a useful tool to ameliorate the deficits resulting from acute and chronic injuries of the mammalian nervous system. Electronic supplementary information (ESI) available: In vitro assays of the stimulatory activity of the L1-peptide, in vitro assays comparing the stimulatory activity of the L1-peptide coupled and not coupled to AuNPs, TEM characterization of AuNPs, additional results of aggregation experiments including an explanatory figure, UV-vis data proving the stability of AuNP@L1/PEGMUA-conjugates in relevant buffers, simple structure modeling of a L1-peptide and PEGMUA on AuNPs, and structure modeling of L1-peptides. See DOI: 10.1039/c3nr02707d

Effect of scandium additions on microstructure and mechanical properties of Al-Zn-Mg alloy welds

International Nuclear Information System (INIS)

Dev, Selvi; Stuart, A. Archibald; Kumaar, R.C. Ravi Dev; Murty, B.S.; Rao, K. Prasad

2007-01-01

The microstructure and mechanical properties of fusion zones of medium strength Al-Zn-Mg alloy (RDE-40) welds obtained by using different fillers containing various amount of scandium was investigated. It was observed that addition of scandium led to very significant grain refinement in the fusion zone especially for scandium levels greater than the eutectic composition (0.55 wt%). The grain refinement led to the reduction in solidification cracking and improved the tensile properties of fusion zone compared to the ones obtained by the commercial AA5556 filler

Microstructure, mechanical properties, in vitro degradation and cytotoxicity evaluations of Mg-1.5Y-1.2Zn-0.44Zr alloys for biodegradable metallic implants.

Science.gov (United States)

Fan, Jun; Qiu, Xin; Niu, Xiaodong; Tian, Zheng; Sun, Wei; Liu, Xiaojuan; Li, Yangde; Li, Weirong; Meng, Jian

2013-05-01

Mg-1.5Y-1.2Zn-0.44Zr alloys were newly developed as degradable metallic biomaterials. A comprehensive investigation of the microstructure, mechanical properties, in vitro degradation assessments and in vitro cytotoxicity evaluations of the as-cast state, as-heat treated state and as-extruded state alloys was done. The microstructure observations show that the Mg-1.5Y-1.2Zn-0.44Zr alloys are mainly composed of the matrix α-Mg phases and the Mg12ZnY secondary phases (LPS structure). The hot extrusion method significantly refined the grains and eliminated the defects of both as-cast and heat treated alloys and thereby contributed to the better mechanical properties and biodegradation resistance. The values of tensile strength and tensile yield strength of the alloy in the as-extruded condition are about 236 and 178 MPa respectively, with an excellent elongation of 28%. Meanwhile, the value of compressive strength is about 471 MPa and the value of bending strength is about 501 MPa. The superior bending strength further demonstrates the excellent ductility of the hot extruded alloys. The results of immersion tests and electrochemical measurements in the SBF indicate that a protective film precipitated on the alloy's surface with the extension of degradation. The protective film contains Mg(OH)2 and hydroxyapatite (HA) which can reinforce osteoblast activity and promote good biocompatibility. No significant cytotoxicity towards L-929 cells was detected and the immersion extracts of alloy samples could enhance the cell proliferation with time in the cytotoxicity evaluations, implying that the Mg-1.5Y-1.2Zn-0.44Zr alloys have the potential to be used for biomedical applications. Copyright © 2013 Elsevier B.V. All rights reserved.

Upregulated ROS production induced by the proteasome inhibitor MG-132 on XBP1 gene expression and cell apoptosis in Tca-8113 cells.

Science.gov (United States)

Chen, Hai-ying; Ren, Xiao-yan; Wang, Wei-hua; Zhang, Ying-xin; Chen, Shuang-feng; Zhang, Bin; Wang, Le-xin

2014-07-01

Exposure of Tca-8113 cells to proteasome inhibitor carbobenzoxy-Leu-Leu-leucinal (MG-132) causing apoptosis is associated with endoplasmic reticulum (ER) stress. X-box-binding protein-1 (XBP1) is an important regulator of a subset of genes active during ER stress, which is related to cell survival and is required for tumor growth. The present study is to evaluate the effect of MG-132 on ROS production, XBP1 gene expression, tumor necrosis factor receptor-associated factor 2 (TRAF2), ASK1 and c-jun protein expression in tongue squamous cell carcinoma cell line Tca-8113 cells. ROS production was measured by reactive oxygen species assay. X-box binding protein-1 (XBP1) mRNA was analyzed by real-time-PCR, TRAF2, ASK1 and c-jun protein were investigated by western blot and immunocytochemistry respectively. The result indicated that ROS production, TRAF2, ASK1 and c-jun were elevated in MG-132 treated cells. Giving ROS scavenger N-acetyl-L-cysteine (NAC) largely prevented the effects of MG-132. Furthermore, treating with MG-132 lead to decreased XBP1 mRNA expression but could not completely block the expression of XBP1. Taken together, these findings provide the evidence that MG-132 induced ER stress lead to Tca-8113 cells apoptosis through ROS generation and TRAF2-ASK1-JNK signal pathway activation. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Plant pigments (antioxidants of medicinal plants Malva Sylvestris l. and Malva Moschata l. (Malvaceae

Directory of Open Access Journals (Sweden)

Sulejman Redžić

2005-05-01

Full Text Available Qualitative-quantitative structure of plant pigments in wild plants Malva silvestrs L. and Malva moschata L. (Malvaceae, which were collected in 20 locations in Sarajevo area and surroundings, was tested during spring and summer in 2003. Acetone extracts of both categories were made and rising paper-chromatography done for the purpose of qualitative analysis. Quantitative analysis was done by spectrophotometry. Chlorophyll a, chlorophyll b and xanthophylls presence was confirmed by separation of pigments from acetone extract of these plant species. Spectrophotometric analysis of acetone extracts showed these results (given in mg/L: chlorophyll a 2,386, chlorophyll b 0,332 and carrotenoides 1,037. Data given in mg/g dry substance are: chlorophyll a 1,193x10(-2, chlorophyll b 1,66x10(-3, and carrotenoides 5,185x10(-3. Pigments structure (in mg/L in species Malva moschata is 1,6 for chlorophyll; 1,419 for chlorophyll b; and 0,364 for carrotenoides. Data given in mg/g are: chlorophyll a 8x10(-3, chlorophyll b 7,09x10(-3, and carrotenoides 1,82x10(-3. Considering that species Malva moschata L. grows on ecologically clear soils as opposed to well-known medicinal species Malvasylvestris L., and considering the production of phytomass, phytochemical structure and pharmacological influence it can be considered very medical and be given advantage over this wider spread category.

Role of cerium, lanthanum, and strontium additions in an Al-Si-Mg (A356) alloy

Energy Technology Data Exchange (ETDEWEB)

Nabawy, Ahmed M.; Samuel, Agnes M.; Samuel, Fawzy H. [Universite du Quebec, Chicoutimi (Canada). Dept. des Sciences Appliquees; Alkahtani, Saleh A.; Abuhasel, Khaled A. [Salman Bin Abdulaziz Univ., Riyadh (Saudi Arabia). Mechanical Engineering Dept.

2016-05-15

The effects of individual and combined additions of cerium (Ce), lanthanum (La), and strontium (Sr) on the eutectic modification and solidification characteristics of an Al-Si-Mg (A356) aluminum alloy were investigated using optical microscopy and thermal analysis techniques. Addition of Ce, La, and Sr resulted in different depression levels of the eutectic nucleation temperature and eutectic growth undercooling, generating modified eutectic structures exhibiting different levels of modification. Microstructural results showed that the best modification levels using individual additions were achieved by Sr which produced a fine fibrous eutectic structure, followed by La, which produced a refined lamellar structure, with Ce providing the lowest level of modification. On the other hand, a combined addition of Ce and Sr provided the highest modification level, with the production of a very fine fibrous eutectic silicon structure. In general, the addition of Sr helped to further increase the refinement obtained in the alloys containing La or Ce + La additions. In the latter alloy, the main intermetallic phases observed were La(Al,Si){sub 2} and Al{sub 20}(La,Ce)Ti{sub 2}Si. The improved modification levels were found to be proportional to the depression in the eutectic nucleation temperature and the eutectic growth undercooling. A high cooling rate also improved the modification level by at least one level.

Insulator layer formation in MgB2 SIS junctions

International Nuclear Information System (INIS)

Shimakage, H.; Tsujimoto, K.; Wang, Z.; Tonouchi, M.

2005-01-01

The dependence of current-voltage characteristics on thin film deposition conditions was investigated using MgB 2 /AlN/NbN SIS junctions. By increasing the substrate temperature in AlN insulator deposition, the current density decreased and the normal resistance increased. The results indicated that an additional insulator layer between the MgB 2 and AlN formed, either before or during the AlN deposition. The thickness of the additional insulator layer was increased with an increase in the AlN deposition temperature. From the dependence of current density on the thickness of AlN in low temperature depositions, the thickness of the additional insulator layer was estimated to be 1-1.5 nm when the AlN insulator was deposited from 0.14 to 0.7 nm. Moreover, with the current density of MgB 2 /AlN/MgB 2 SIS junctions, further insulator layer formation was confirmed

Linagliptin potentiates the effect of l-dopa on the behavioural, biochemical and immunohistochemical changes in experimentally-induced Parkinsonism: Role of toll-like receptor 4, TGF-β1, NF-κB and glucagon-like peptide 1.

Science.gov (United States)

Kabel, Ahmed M; Omar, Mohamed S; Alhadhrami, A; Alharthi, Salman S; Alrobaian, Majed M

2018-05-01

Our aim was to assess the effect of different doses of linagliptin with or without l-dopa/Carbidopa on 1-methyl-4-phenyl-1,2,3,6-tetrahydropyridine (MPTP)-induced parkinsonism in mice. Eighty Balb/c mice were divided into 8 equal groups: Control; MPTP; MPTP + l-dopa/Carbidopa; MPTP + linagliptin 3 mg/kg/day; MPTP + linagliptin 10 mg/kg/day; MPTP + Carboxymethyl cellulose; MPTP + l-dopa/Carbidopa + linagliptin 3 mg/kg/day and MPTP + l-dopa/Carbidopa + linagliptin 10 mg/kg/day. Striatal dopamine, tumor necrosis factor alpha (TNF-α), interleukin 10 (IL-10), transforming growth factor beta 1 (TGF-β1), toll-like receptor 4 (TLR4), antioxidant enzymes, adenosine triphosphate (ATP), glucagon-like peptide-1 (GLP-1), receptors of advanced glycation end products (RAGE), nuclear factor (erythroid-derived 2)-like 2 (Nrf2), heme oxygenase-1 (HO-1), mitochondrial complex I activity, catalepsy and total swim scores were measured. Also, the substantia nigra was subjected to immunohistochemical examination. The combination of l-dopa/Carbidopa and linagliptin in a dose-dependent manner resulted in significant improvement of the behavioural changes, striatal dopamine, antioxidant parameters, Nrf2/HO-1 content, GLP-1, ATP and mitochondrial complex I activity with significant decrease in striatal RAGE, TGF-β1, TNF-α, IL-10, TLR4 and alleviated the immunohistochemical changes better than the groups that received either l-dopa/Carbidopa or linagliptin alone. The combination of l-dopa/Carbidopa and linagliptin might represent a promising therapeutic modality for management of parkinsonism. Copyright © 2018 Elsevier Inc. All rights reserved.

The effects of Mg addition on the microstructure and mechanical properties of thixoformed Al–5%Si–Cu alloys

Energy Technology Data Exchange (ETDEWEB)

Salleh, M.S., E-mail: shukor@utem.edu.my [Department of Mechanical and Materials Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 Selangor (Malaysia); Department of Manufacturing Process, Faculty of Manufacturing Engineering, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka (Malaysia); Omar, M.Z., E-mail: zaidi@eng.ukm.my [Department of Mechanical and Materials Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 Selangor (Malaysia); Syarif, J., E-mail: syarif@eng.ukm.my [Department of Mechanical and Materials Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 Selangor (Malaysia)

2015-02-05

Highlights: • The average globule size of α-Al decreased when Mg amount is increased. • T6 heat treatment has increased the strength of the thixoformed alloys. • The elongation after T6 heat treatment is even significantly improved. • Thixoformed alloy with high Mg content shows a brittle type fracture. • Thixoformed alloy in T6 condition shows a ductile type fracture. - Abstract: In this study, the effects of different amounts of magnesium (Mg) on the microstructures and tensile properties of thixoformed Al–5%Si–Cu alloys were investigated. Three different alloys containing various amounts of Mg (0.5, 0.8 and 1.2 wt%) were prepared through the cooling slope casting technique, before they were thixoformed using a compression press. Several of the thixoformed samples were then treated with a T6 heat treatment, that is, solution treatment at 525 °C for 8 h, quenching in warm water at 60 °C, followed by aging at 155 °C for 4 h. All of the samples were then characterised by optical microscopy (OM), scanning electron microscopy (SEM) energy dispersive X-ray (EDX) spectroscopy and X-ray diffraction (XRD) analysis as well as by tensile tests. The results revealed that magnesium was able to refine the size of α-Al globules and the eutectic silicon in the samples. It was also observed that a compact π-Al{sub 9}FeMg{sub 3}Si{sub 5} phase was formed when the magnesium content was 0.8 wt% and 1.2 wt%. The mechanical properties of the thixoformed alloys improved significantly after the T6 heat treatment. The highest attainment was recorded by the latter alloy (i.e. with 1.2 wt%Mg) with its ultimate tensile strength (UTS) as high as 306 MPa, yield strength (YS), 264 MPa, and elongation to fracture of 1.8%. The fracture of thixoformed alloy with a low Mg content (0.5 wt%) showed a combination of dimple and cleavage fracture, whereas in the alloy that contained the highest Mg content (1.2 wt%), cleavage fracture was observed.

Hydriding and dehydriding rates of Mg, Mg-10TaF5, and Mg-10NbF5 prepared via reactive mechanical grinding

Science.gov (United States)

Song, Myoung Youp; Kwak, Young Jun; Lee, Seong Ho; Park, Hye Ryoung

2015-01-01

In this work, TaF5 and NbF5 were chosen as additives to enhance the hydriding and dehydriding rates of Mg. Mg, Mg-10TaF5, and Mg-10NbF5 samples were prepared by reactive mechanical grinding. The hydriding and dehydriding properties of the samples were then examined. Mg-10TaF5 had the largest amount of hydrogen absorbed for 30 min and the highest initial dehydriding rate after incubation period, followed in order by Mg-10NbF5, and Mg. At 593 K under 12 bar H2 at the first cycle, Mg-10TaF5 absorbed 3.63 wt% H for 5 min and 4.53 wt% H for 30 min. At 593 K under 1.0 bar H2 at the first cycle, Mg-10TaF5 desorbed 0 wt% H for 2.5 min, 0.59 wt% H for 5 min, 3.42 wt% H for 30 min, and 4.24 wt% H for 60 min. The reactive mechanical grinding of Mg with TaF5 or NbF5 is believed to have facilitated the nucleation and to have decreased the diffusion distances of hydrogen atoms. These two effects are believed to have increased the hydriding and dehydriding rates of Mg. The MgF2 and Ta2H formed in Mg-10TaF5, and the MgF2, NbH2, and NbF3 formed in Mg-10NbF5 are considered to have enhanced both of these effects.

Thermodynamics of HEDPA protonation in different media and complex formation with Mg2+ and Ca2+

International Nuclear Information System (INIS)

Foti, Claudia; Giuffrè, Ottavia; Sammartano, Silvio

2013-01-01

Highlights: • Acid–base properties of etidronic acid in different ionic media and at different ionic strengths. • Complex formation of etidronate with Na + , K + , Ca 2+ and Mg 2+ . • Dependence on ionic strength analysed by a Debye–Hückel type equation and the SIT approach. • Suggested protonation constants calculated at I = 0.1 mol · L −1 and t = 25 °C, in different ionic media. -- Abstract: Acid–base properties of etidronic acid [(1-Hydroxyethane-1,1-diyil)bis(phosphonic acid), HEDPA] in different ionic media and at different ionic strengths (NaCl, KCl: I ⩽ 2 mol · L −1 ; (C 2 H 5 ) 4 NI: I ⩽ 1 mol · L −1 ) were studied at t = 25 °C, determining, by potentiometric and calorimetric techniques, protonation constants and enthalpy changes. The differences in the protonation constants in the different supporting electrolytes were also interpreted in terms of weak complex formation with M i L (with i = 1, 2), MLH j (with j = 1, 2, 3) and M 2 LH species (with L = HEDPA; M = Na + , K + ). The formation constants for the species of Ca 2+ and Mg 2+ , were determined by potentiometric titrations at different ionic strengths (0.1 ⩽ I/mol · L −1 ⩽ 1) in NaCl at t = 25 °C. The stability of these species is fairly high, as an example, at I = 0.1 mol · L −1 and t = 25 °C, for ML species, log β = 6.52 and 6.86, for Ca 2+ and Mg 2+ , respectively, obtained by considering simultaneously HEDPA–Na + interactions. The dependence on ionic strength was analysed by a Debye–Hückel type equation and the SIT (Specific ion Interaction Theory) approach for protonation thermodynamic parameters and by a Debye–Hückel type equation for Mg 2+ and Ca 2+ complex formation. The sequestering ability of HEDPA toward Ca 2+ and Mg 2+ was also analysed. A comparison with literature data is given

Phenolics in Slovenian bilberries ( Vaccinium myrtillus L.) and blueberries ( Vaccinium corymbosum L.).

Science.gov (United States)

Moze, Spela; Polak, Tomaz; Gasperlin, Lea; Koron, Darinka; Vanzo, Andreja; Poklar Ulrih, Natasa; Abram, Veronika

2011-07-13

Phenolics from bilberries ( Vaccinium myrtillus L.) sampled from seven different locations and highbush blueberries ( Vaccinium corymbosum L.) from one location in Slovenia were analyzed. In samples of both species 15 anthocyanins were identified by LC-MS/MS. Their contents were expressed as cyanidin 3-glucoside equivalents (C3GE); bilberries contained 1210.3 ± 111.5 mg C3GE/100 g fw and blueberries 212.4 ± 14.1 mg C3GE/100 g fw. Glycosides of delphinidin and cyanidin were predominant (488.5 vs 363.6 mg C3GE/100 g fw) in the bilberries and glycosides of malvidin (108.0 vs 100.8 mg C3GE/100 g fw) in the blueberries, whereas the contents of peonidin were lowest (74.5 vs 4.8 mg C3GE/100 g fw) in both berries. The contents of flavanols, flavonols, phenolic acids, and stilbenes were determined by LC-MS. For the first time, rutin was identified (bilberries, 0.2 ± 0.0 mg/100 g fw; blueberries, 3.1 ± 0.1 mg/100 g fw). Chlorogenic acid (as 3-caffeoylquinic acid) was the most abundant among the phenolic acids (23.1 ± 1.0 mg/100 g fw in bilberries and 70.0 ± 3.4 mg/100 g fw in blueberries). Statistical analysis shows that the content of 27 individual flavonoids, phenolic acids, and stilbenes can be used to identify the picking region of these Slovenian bilberries.

Apport du traitement d'images dans le suivi de l'influence des teneurs en nutriments sur la croissance des lentilles d'eau (Lemna minor

Directory of Open Access Journals (Sweden)

Tangou, TT.

2014-01-01

Full Text Available Contribution of image processing in monitoring the influence of nutrients on the growth of duckweed (Lemna minor. The growth of duckweed (Lemna minor is an important component in the treatment process in wastewater floating macrophyte ponds. An excess or shortage of this biomass may be responsible for the dysfunction of such ponds. Modeling these duckweed ponds through mass balances based on Petersen's matrix may be helpful in facilitating the optimal management of such facilities. This study sought to assess the efficiency of digital image processing in the growth monitoring of Lemna minor under different concentrations of nitrogen and phosphorus. The experiments were carried out in a growth chamber (phytotron using an experimental pilot involving initial fresh Lemna minor biomass (1 g, nitrogen and phosphorus concentrations varying between 5 and 64 mg N-NH4+·l-1, and 1 and 24 mg P-PO43-·-1, respectively. Digital image processing was achieved in addition to gravimetric methods (fresh weight and/or dry weight. Our results showed that the image processing method allowed a continuous and non-destructive monitoring of duckweed biomass. The growth of Lemna minor progressively decreased when nitrogen and phosphorus concentrations were greater than 16 mg N-NH4+·l-1 and 6 mg P-PO43-·-1. The maximum growth rates μmax were of the order of 0.07 d-1. The kinetic constants KS and KI were respectively 3.83 mg·l-1 and 204 mg·l-1 for nitrogen, and 1.26 mg·l-1 and 13.3 mg·l-1 for phosphorus. Such results are interesting as they could contribute to the optimal management of Lemna minor and the modeling of biological reactors.

Compréhension de la stabilité thermique des alliages d'aluminium Al-Cu-Mg Understanding of the thermal stability of Al-Cu-Mg aluminum alloys

Directory of Open Access Journals (Sweden)

Pouget Gaëlle

2013-11-01

Full Text Available Les alliages d'aluminium 2xxx (Al-Cu-Mg sont connus pour être performants à chaud et sont par exemple utilisés pour certaines pièces de structure des avions. L'effet de la composition en Cu et Mg sur leur stabilité thermique, ainsi que celui de la précipitation durcissante associée ont été étudiés. Des comportements différents sont observés et trois zones de composition (en poids % identifiées: 3,1–3,7Cu et 1,6–2,0Mg : durcissement par la phase S' (Al2CuMg, limite d'élasticité ∼ 465 MPa à l'état T8 et bonne stabilité thermique jusqu'à 200 ∘C. 4,8–5,4Cu et 0–0,4Mg : durcissement par la phase θ' (Al2Cu, limite d'élasticité ∼ 380 MPa à l'état T8 et bonne stabilité thermique jusqu'à 300 ∘C. 3,7–4,3Cu et 0,9–1,3Mg : durcissement par S'+ θ', limite d'élasticité ∼ 470 MPa à l'état T8 mais stabilité thermique insuffisante à 150 ∘C et au delà; ce vieillissement important est associé à une concentration en Cu en solution solide élevée, ce qui accélère la cinétique de coalescence des précipités. La première zone de composition est donc recommandée pour des applications à température intermédiaire, typiquement 150 ∘C, et la seconde pour des applications à plus haute température, entre 250 et 300 ∘C. La troisième zone est à éviter pour des applications à 150 ∘C et au-delà. 2xxx aluminum alloys (Al-Cu-Mg have a good behaviour at elevated temperature and are used for some aircraft's structural parts. In this study, the effect of Cu and Mg content on the thermal stability and strengthening precipitation has been investigated. Three different behaviours are observed depending on the alloy composition: 3.1–3.7Cu, 1.6–2.0Mg: strengthening by S' (Al2CuMg, yield strength ∼ 465 MPa in T8 temper and good thermal stability up to 200 ∘C. 4.8–5.4Cu, 0–0.4Mg: strengthening by θ' (Al2Cu, yield strength ∼ 380 MPa in T8 and good thermal stability up to

Re-examining the 26Mg(α ,α')26Mg reaction: Probing astrophysically important states in 26Mg

Science.gov (United States)

Adsley, P.; Brümmer, J. W.; Li, K. C. W.; Marín-Lámbarri, D. J.; Kheswa, N. Y.; Donaldson, L. M.; Neveling, R.; Papka, P.; Pellegri, L.; Pesudo, V.; Pool, L. C.; Smit, F. D.; van Zyl, J. J.

2017-11-01

Background: The 22Ne(α ,n )25Mg reaction is one of the neutron sources for the s process in massive stars. The properties of levels in 26Mg above the α -particle threshold control the strengths of the 22Ne(α ,n )25Mg and 22Ne(α ,γ )26Mg reactions. The strengths of these reactions as functions of temperature are one of the major uncertainties in the s process. Purpose: Information on the existence, spin, and parity of levels in 26Mg can assist in constraining the strengths of the 22Ne(α ,γ )26Mg and 22Ne(α ,n )25Mg reactions, and therefore in constraining s -process abundances. Methods: Inelastically scattered α particles from a 26Mg target were momentum-analyzed in the K600 magnetic spectrometer at iThemba LABS, South Africa. The differential cross sections of states were deduced from the focal-plane trajectory of the scattered α particles. Based on the differential cross sections, spin and parity assignments to states are made. Results: A newly assigned 0+ state was observed in addition to a number of other states, some of which can be associated with states observed in other experiments. Some of the deduced Jπ values of the states observed in the present study show discrepancies with those assigned in a similar experiment performed at RCNP Osaka. The reassignments and additions of the various states can strongly affect the reaction rate at low temperatures. Conclusion: The number, location, and assignment of levels in 26Mg that may contribute to the 22Ne+α reactions are not clear. Future experimental investigations of 26Mg must have an extremely good energy resolution to separate the contributions from different levels. Coincidence experiments of 26Mg provide a possible route for future investigations.

Basal cell carcinoma: PD-L1/PD-1 checkpoint expression and tumor regression after PD-1 blockade.

Science.gov (United States)

Lipson, Evan J; Lilo, Mohammed T; Ogurtsova, Aleksandra; Esandrio, Jessica; Xu, Haiying; Brothers, Patricia; Schollenberger, Megan; Sharfman, William H; Taube, Janis M

2017-01-01

Monoclonal antibodies that block immune regulatory proteins such as programmed death-1 (PD-1) have demonstrated remarkable efficacy in controlling the growth of multiple tumor types. Unresectable or metastatic basal cell carcinoma, however, has largely gone untested. Because PD-Ligand-1 (PD-L1) expression in other tumor types has been associated with response to anti-PD-1, we investigated the expression of PD-L1 and its association with PD-1 expression in the basal cell carcinoma tumor microenvironment. Among 40 basal cell carcinoma specimens, 9/40 (22%) demonstrated PD-L1 expression on tumor cells, and 33/40 (82%) demonstrated PD-L1 expression on tumor-infiltrating lymphocytes and associated macrophages. PD-L1 was observed in close geographic association to PD-1+ tumor infiltrating lymphocytes. Additionally, we present, here, the first report of an objective anti-tumor response to pembrolizumab (anti-PD-1) in a patient with metastatic PD-L1 (+) basal cell carcinoma, whose disease had previously progressed through hedgehog pathway-directed therapy. The patient remains in a partial response 14 months after initiation of therapy. Taken together, our findings provide a rationale for testing anti-PD-1 therapy in patients with advanced basal cell carcinoma, either as initial treatment or after acquired resistance to hedgehog pathway inhibition.

The Effect of CaO and MgO as Expanding Additives to Improve Cement Isolation Strength under HPHT Exposure

Directory of Open Access Journals (Sweden)

Rudi Rubiandini

2005-05-01

Full Text Available Cementing is one of the most important parts in oil-well drilling. Recent development in oil-well drilling technology has led to a more problematic case in cementing. High temperature cementing is one of the problems. High temperature cementing may cover steam recovery wells, geothermal wells and ultra deep wells.The use of expanding cements as an effort to improve the sealing efficacy of annulus cementing has been considered for a long time as a promising solution to the existing problems. CaO and MgO have been proposed as two of the most effective additives to create excellent expanding cement. The purpose of this study is to find the effect of adding up burnt pure CaO and MgO to the value of compressive strength and shear bond strength of API class G cement in high pressure and high temperature condition. The method that we used within this research is an evaluation of the data taken from a simulator that simulated within temperature range of 100 – 250oC and pressure of 2000 psi.The conclusion is taken according to the results which saying that the addition of burnt pure CaO and MgO would increase the shear bond strength and the compressive strength on specific condition up to 200oC temperature. The addition won’t be effective for the condition of 250oC temperature. The behavior of cement strength was also influenced by the length of curing time.Further more, research on expanding cement needs to be developed and extended whether to vary its compositions, temperatures, or curing time conditions. The compatibility when mixed with other additives together with silica flour has not yet been figured out.

Hilic MS/MS determination of amino acids in herbs of Fumaria schleicheri L., Ocimum basilicum L., and leaves of Corylus avellana L.

Science.gov (United States)

Prokopenko, Yuliya; Jakštas, Valdas; Žvikas, Vaidotas; Georgiyants, Victoriya; Ivanauskas, Liudas

2018-05-18

The aim of research was to study the content of amino acids using in extracts of Fumaria schleicheri L., Ocimum basilicum L., and Corylus avellana L. by HILIC MS/MS method. Separation of amino acids in the samples was carried out with Acquity H-class UPLC system (Waters, Milford, USA) equipped with SeQuant ZIC-Hilic collumn (2.1 × 150 mm, 3.5 μm) (Merck Millipore, Darmstadt, Germany). The MS/MS fragment ion chromatograms of the test solutions established the presence of 19 amino acids. The obtained results have shown that O. basilicum L. characterized the highest concentrations of different neurogenic amino acids (128.1 mg/kg), comparing with F. schleicheri L. and C. avellana L. (57.72 and 52.91 mg/kg, respectively).

Antimycobacterial activity evaluation and MIC determination of liophilizated hydroalcoholic extracts of Bixa orellana L., Bixaceae

Directory of Open Access Journals (Sweden)

Renata B. Silva

Full Text Available Bixa orellana is used in popular medicine against several diseases. Extracts of its fruit, root and leaf presented antimicrobial activity, while seed extract showed negative results. This study aimed at verifying the antimycobacterial activity of B. orellanalyophilized hydroalcoholic extracts over Mycobacterium tuberculosis, and determine the Minimum Inhibitory Concentration against five bacteria. Antimycobacterial activity was determined by diffusion technique, while MIC was assessed by diffusion and colorimetric analysis. MICs were 0.3, 0.5 and 0.2 mg/mL respectively, for leaf, root and stem extracts, against M. tuberculosis. Stem's extract showed 1.2 mg/mL for B. cereus, 1.53 mg/mL for S. aureusand S. typhimurium, 4.50 mg/mL for P. aeruginosaand 8.01 mg/mL for P. mirabillis.Leaf extracts showed 0.66 mg/mL for P. aeruginosa, 0.94 mg/mL for P. mirabillis, 1.88 mg/mL for S. aureus, 3.95 mg/mL for B. cereusand 8.37 mg/mL for S. typhimurium. Root's extracts showed 0.25 mg/mL for P. aeruginosa,0.31 mg/mL for S. aureus, 0.62 mg/mL for S. typhimuriumand 3.00 mg/mL for B. cereusand P. mirabillis. Leaf and stem extracts showed antimycobacterial activity. MICs were lower in colorimetric analysis than in agar diffusion. Extracts revealed bacteriostatic activity against the five bacterial.

Molecular mechanism of PD-1/PD-L1 blockade via anti-PD-L1 antibodies atezolizumab and durvalumab.

Science.gov (United States)

Lee, Hyun Tae; Lee, Ju Yeon; Lim, Heejin; Lee, Sang Hyung; Moon, Yu Jeong; Pyo, Hyo Jeong; Ryu, Seong Eon; Shin, Woori; Heo, Yong-Seok

2017-07-17

In 2016 and 2017, monoclonal antibodies targeting PD-L1, including atezolizumab, durvalumab, and avelumab, were approved by the FDA for the treatment of multiple advanced cancers. And many other anti-PD-L1 antibodies are under clinical trials. Recently, the crystal structures of PD-L1 in complex with BMS-936559 and avelumab have been determined, revealing details of the antigen-antibody interactions. However, it is still unknown how atezolizumab and durvalumab specifically recognize PD-L1, although this is important for investigating novel binding sites on PD-L1 targeted by other therapeutic antibodies for the design and improvement of anti-PD-L1 agents. Here, we report the crystal structures of PD-L1 in complex with atezolizumab and durvalumab to elucidate the precise epitopes involved and the structural basis for PD-1/PD-L1 blockade by these antibodies. A comprehensive comparison of PD-L1 interactions with anti-PD-L1 antibodies provides a better understanding of the mechanism of PD-L1 blockade as well as new insights into the rational design of improved anti-PD-L1 therapeutics.

Phosphorus Doped Zn 1- x Mg x O Nanowire Arrays

KAUST Repository

Lin, S. S.; Hong, J. I.; Song, J. H.; Zhu, Y.; He, H. P.; Xu, Z.; Wei, Y. G.; Ding, Y.; Snyder, R. L.; Wang, Z. L.

2009-01-01

We demonstrate the growth of phosphorus doped Zn 1-xMg xO nanowire (NW) using pulsed laser deposition. For the first time, p-type Zn 0.92Mg 0.08O:P NWs are likely obtained In reference to atomic force microscopy based piezoelectric output

Pork carcass injury in slaughterhouse waiting area and nutrient addition in pre-slaughter fasting

Directory of Open Access Journals (Sweden)

Tiago G Petrolli

2017-01-01

Full Text Available Objective. Two experiments were conducted on a slaughterhouse located in Brazil, which the first aimed at evaluating the injuries on pig skin and carcass resulting from slaughterhouse waiting area management and the second aimed at assessing how glucose (G, sodium bicarbonate (SB and vitamin E (VE added to water during pre-slaughter fasting may affect carcass yield, organ relative weight and pork meat quality characteristics. Materials and methods. First trial included 1000 pigs, which were observed in the slaughterhouse resting area until the moment they entered the stunning process area. In the second trial were used 500 animals distributed on the last pre-slaughter day in a completely randomized design, including ten treatments and ten replicates. The treatments were: water; 50 g/L G; 50 g/L G + 200 mg/L of VE; 75 g/L of G; 75 g/L of G + 200 mg VE; 0.45% SB; 0.45% SB + 200 mg/L of VE; 0.55% SB; 0.55% SB + 200 mg/L of VE; 200 mg/L of VE. Results. Carcass yield and relative organ weight were not affected by treatments. The addition of 0.55% SB + 200 mg VE reduced the final pH of meat, and of 0.45% SB reduced the red pigment intensity. Conclusions. The main occurrences of injuries to the skin and carcass of pigs are due to fights. Also, adding glucose, sodium bicarbonate, and vitamin E to diet did not affect the carcass and viscera yield and meat quality.

Thirteen week toxicity study of dietary l-tryptophan in rats with a recovery period of 5 weeks.

Science.gov (United States)

Shibui, Yusuke; Matsumoto, Hideki; Masuzawa, Yoko; Ohishi, Takumi; Fukuwatari, Tsutomu; Shibata, Katsumi; Sakai, Ryosei

2018-04-01

Although l-tryptophan is nutritionally important and widely used in medical applications, toxicity data for its oral administration are limited. The purpose of this study was to evaluate the potential toxicity of an experimental diet containing added l-tryptophan at doses of 0 (basal diet), 1.25%, 2.5% and 5.0% when administered to Sprague-Dawley rats for 13 weeks. There were no toxicological changes in clinical signs, ophthalmology, urinalysis, hematology, necropsy, organ weight and histopathology between control rats and those fed additional l-tryptophan. Body weight gain and food consumption significantly decreased throughout the administration period in males in the 2.5% group and in both sexes in the 5.0% group. At the end of the dosing period, decreases in water intake in males in the 5.0% group and in serum glucose in females in the 5.0% group were observed. The changes described above were considered toxicologically significant; however, they were not observed after a 5 week recovery period, suggesting reversibility. Consequently, the no-observed-adverse-effect level of l-tryptophan in the present study was 1.25% for males and 2.5% for females (mean intake of l-tryptophan: 779 mg kg -1 body weight day -1 [males] and 1765 mg kg -1 body weight day -1 [females]). As the basal diet used in this study contained 0.27% of proteinaceous l-tryptophan, the no-observed-adverse-effect level of overall l-tryptophan was 1.52% for males and 2.77% for females (mean intake of overall l-tryptophan: 948 mg kg -1 body weight day -1 (males) and 1956 mg kg -1 body weight day -1 (females)). We conclude that l-tryptophan has a low toxicity profile in terms of human use. Copyright © 2017 John Wiley & Sons, Ltd.

Study of agronomic characteristics and advantage indices in intercropping of additive series of Chickpea (Cicer arietinum L.) and Black Cumin (Nigella sativa L.)

OpenAIRE

esmaeil rezaei-chiyaneh; Esmaeil Gholinezhad

2015-01-01

Study of agronomic characteristics and advantage indices in intercropping of additive series of Chickpea (Cicer arietinum L.) and Black Cumin (Nigella sativa L.) Abstract In order to evaluate quantitive and qualitive yield of Chickpea (Cicer arietinum L.) and Black Cumin (Nigella sativa L.) in intercropping of additive series, a field experiment was arranged in a randomized complete block design with three replications in West Azerbaijan province- city Nagadeh, Iran during growing r...

In vitro shoot regeneration and microcorm development in crocus vernus (l.) hill

International Nuclear Information System (INIS)

Sivanesan, I.

2014-01-01

An efficient method has been developed for In vitro regeneration of shoot and microcorm from corm explants of Crocus vernus. Corms were cut into 0.5-1.0 cm long segments and cultured on the SH medium supplemented with 0.5, 1.0, 2.0, or 4.0 mg L-1 2-isopentyl adenine (2-iP), N6-benzyladenine (BA), and N6-furfuryladenine (kinetin, Kin) alone or combination with 0.5 or 1.0 mg L-1 alpha-naphthalene acetic acid (NAA) for shoot regeneration. Of the three cytokinins tested, BA was found to be the most effective cytokinin for shoot formation. The number of shoots induced per explant was more when BA was combined with 0.5 mg L-1 NAA than with 1.0 mg L-1 NAA. The greatest percentage of shoot induction (97.2) with the mean number of 11.8 shoots per explant was obtained when the SH medium was supplemented with 2.0 mg L-1 BA and 0.5 mg L-1 NAA. The frequency of microcorm induction was significantly affected by the concentrations of sucrose.The greatest number of 6.1 microcorms per explant was obtained when the SH medium was supplemented with 2.0 mg L-1 BA, 0.5 mg L-1 NAA and 6.0% sucrose. The microcorms formed In vitro developed daughter corms when they were cultured on this medium. Microcorms were separated from the culture and planted out in acclimatization boxes containing a commercial medium. About 85% of corms developed shoot and root after 30 days. This protocol could be utilized for genetic transformation and mass clonal propagation of C. (author)

High-Throughput Investigation of a Lead-Free AlN-Based Piezoelectric Material, (Mg,Hf)xAl1-xN.

Science.gov (United States)

Nguyen, Hung H; Oguchi, Hiroyuki; Van Minh, Le; Kuwano, Hiroki

2017-06-12

We conducted a high-throughput investigation of the fundamental properties of (Mg,Hf) x Al 1-x N thin films (0 piezoelectric materials. For the high-throughput investigation, we prepared composition-gradient (Mg,Hf) x Al 1-x N films grown on a Si(100) substrate at 600 °C by cosputtering AlN and MgHf targets. To measure the properties of the various compositions at different positions within a single sample, we used characterization techniques with spatial resolution. X-ray diffraction (XRD) with a beam spot diameter of 1.0 mm verified that Mg and Hf had substituted into the Al sites and caused an elongation of the c-axis of AlN from 5.00 Å for x = 0 to 5.11 Å for x = 0.24. In addition, the uniaxial crystal orientation and high crystallinity required for piezoelectric materials to be used as application devices were confirmed. The piezoelectric response microscope indicated that this c-axis elongation increased the piezoelectric coefficient almost linearly from 1.48 pm/V for x = 0 to 5.19 pm/V for x = 0.24. The dielectric constants of (Mg,Hf) x Al 1-x N were investigated using parallel plate capacitor structures with ∼0.07 mm 2 electrodes and showed a slight increase by substitution. These results verified that (Mg,Hf) x Al 1-x N is a promising material for piezoelectric-based application devices, especially for vibrational energy harvesters.

Dynamic compressive response of wrought and additive manufactured 304L stainless steels

Directory of Open Access Journals (Sweden)

Nishida Erik

2015-01-01

Full Text Available Additive manufacturing (AM technology has been developed to fabricate metal components that include complex prototype fabrication, small lot production, precision repair or feature addition, and tooling. However, the mechanical response of the AM materials is a concern to meet requirements for specific applications. Differences between AM materials as compared to wrought materials might be expected, due to possible differences in porosity (voids, grain size, and residual stress levels. When the AM materials are designed for impact applications, the dynamic mechanical properties in both compression and tension need to be fully characterized and understood for reliable designs. In this study, a 304L stainless steel was manufactured with AM technology. For comparison purposes, both the AM and wrought 304L stainless steels were dynamically characterized in compression Kolsky bar techniques. They dynamic compressive stress-strain curves were obtained and the strain rate effects were determined for both the AM and wrought 304L stainless steels. A comprehensive comparison of dynamic compressive response between the AM and wrought 304L stainless steels was performed. SAND2015-0993 C.

The effect of substrate temperature upon the compositions of Mg and Se in Zn{sub 1-x}Mg{sub x}Se{sub y}Te{sub 1-y} layer grown by MOVPE

Energy Technology Data Exchange (ETDEWEB)

Nishio, M.; Ito, R.; Tanaka, K.; Urata, K.; Nakamura, Y.; Tanaka, T. [Department of Electrical and Electronic Engineering, Graduate School of Science and Engineering, Saga University, 1 Honjo, Saga 840-8502 (Japan); Saito, K.; Guo, Q.X. [Synchrotron Light Application Center, Saga University, 1 Honjo, Saga 840-8502 (Japan)

2014-07-15

The growth of Zn{sub 1-x}Mg{sub x}Se{sub y}Te{sub 1-y} layers was performed on (100) ZnTe substrate by metalorganic vapour phase epitaxy using dimethylzinc, bis-methylcyclopentadienyl-magnesium, diethyltelluride and diethylselenide. The effects of substrate temperature upon the compositions of Mg and Se have been investigated. The Mg composition in Zn{sub 1-x}Mg{sub x}Se{sub y}Te{sub 1-y} layer is significantly enhanced at low substrate temperature. Although the Se composition decreases with decreasing the substrate temperature, Zn{sub 1-x}Mg{sub x}Se{sub y}Te{sub 1-y} layer with a relatively high Se composition of 0.3 is obtainable at a low substrate temperature as low as 380 C. For all the layers, a two-mode behaviour with ZnTe- and MgTe-like longitudinal optical phonon modes is confirmed by Raman scattering. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

( Linum usitatissimum L. cv. Modran cell suspension culture