Chitosan/Carboxymethylcellulose/Ionic Liquid/Ag(0) Nanoparticles Form a Membrane with Antimicrobial Activity

International Nuclear Information System (INIS)

Quadros, C.; Faria, V.W.; Scheeren, C.W.; Klein, M.P.; Hertz, P.F.

2013-01-01

Silver metal nanoparticles were immobilized in chitosan/carboxymethylcellulose/BMI.BF4(1-n-butyl-3-methylimidazolium tetrafluoroborate ionic liquid) (CS/CMC/IL) to form polymeric membrane with 20 μm thickness. The CS/CMC/IL polymeric membrane was prepared using a simple solution blending method. Irregularly shaped Ag(0) nanoparticles with monomodal size distributions of nm Ag(0) were immobilized in the membrane. The presence of small Ag(0) nanoparticles induced an augmentation in the CS/CMC/IL film surface areas. The CS/CMC/IL membrane containing Ag(0) showed increase antimicrobial activity the Ag(0) concentration increased up to saturation at 10 mg. CS/CMC/IL membrane that contains Ag(0) nanoparticles has enhanced durability of the membrane and exhibited stronger antimicrobial activity against Escherichia coli and Staphylococcus aureus.

Virus Disinfection in Water by Biogenic Silver Immobilized in Polyvinylidene Fluoride Membranes

Energy Technology Data Exchange (ETDEWEB)

B De Gusseme; T Hennebel; E Christiaens; H Saveyn; K Verbeken; J Fitts; N Boon; W Vertraete

2011-12-31

The development of innovative water disinfection strategies is of utmost importance to prevent outbreaks of waterborne diseases related to poor treatment of (drinking) water. Recently, the association of silver nanoparticles with the bacterial cell surface of Lactobacillus fermentum (referred to as biogenic silver or bio-Ag{sup 0}) has been reported to exhibit antiviral properties. The microscale bacterial carrier matrix serves as a scaffold for Ag{sup 0} particles, preventing aggregation during encapsulation. In this study, bio-Ag{sup 0} was immobilized in different microporous PVDF membranes using two different pre-treatments of bio-Ag{sup 0} and the immersion-precipitation method. Inactivation of UZ1 bacteriophages using these membranes was successfully demonstrated and was most probably related to the slow release of Ag{sup +} from the membranes. At least a 3.4 log decrease of viruses was achieved by application of a membrane containing 2500 mg bio-Ag{sup 0}{sub powder} m{sup -2} in a submerged plate membrane reactor operated at a flux of 3.1 L m{sup -2} h{sup -1}. Upon startup, the silver concentration in the effluent initially increased to 271 {mu}g L{sub -1} but after filtration of 31 L m{sup -2}, the concentration approached the drinking water limit (= 100 {mu}g L{sup -1}). A virus decline of more than 3 log was achieved at a membrane flux of 75 L m{sup -2} h{sup -1}, showing the potential of this membrane technology for water disinfection on small scale.

Role of Ag-alloy in the thermal stability of Ag-based ohmic contact to GaN(0 0 0 1) surface

International Nuclear Information System (INIS)

Xiong, Zhihua; Qin, Zhenzhen; Zhao, Qian; Chen, Lanli

2015-01-01

First-principles calculations are performed to study Ag and Ag-alloy adsorption stability on GaN(0 0 0 1) surface. We find Ag only contact to GaN surface is unstable under high temperature. While Ag-alloy adsorption exhibits better adsorption stability and electronic properties than that of the Ag only contact,due to the enhanced interaction between Ag-alloy and GaN(0 0 0 1) surface. The Ag-alloy, particularly AgNi, is proposed to be used as very promising ohmic contact to GaN for practical applications

New procedure of selected biogenic amines determination in wine samples by HPLC

Energy Technology Data Exchange (ETDEWEB)

Piasta, Anna M.; Jastrzębska, Aneta, E-mail: aj@chem.uni.torun.pl; Krzemiński, Marek P.; Muzioł, Tadeusz M.; Szłyk, Edward

2014-06-27

Highlights: • We proposed new procedure for derivatization of biogenic amines. • The NMR and XRD analysis confirmed the purity and uniqueness of derivatives. • Concentration of biogenic amines in wine samples were analyzed by RP-HPLC. • Sample contamination and derivatization reactions interferences were minimized. - Abstract: A new procedure for determination of biogenic amines (BA): histamine, phenethylamine, tyramine and tryptamine, based on the derivatization reaction with 2-chloro-1,3-dinitro-5-(trifluoromethyl)-benzene (CNBF), is proposed. The amines derivatives with CNBF were isolated and characterized by X-ray crystallography and {sup 1}H, {sup 13}C, {sup 19}F NMR spectroscopy in solution. The novelty of the procedure is based on the pure and well-characterized products of the amines derivatization reaction. The method was applied for the simultaneous analysis of the above mentioned biogenic amines in wine samples by the reversed phase-high performance liquid chromatography. The procedure revealed correlation coefficients (R{sup 2}) between 0.9997 and 0.9999, and linear range: 0.10–9.00 mg L{sup −1} (histamine); 0.10–9.36 mg L{sup -1} (tyramine); 0.09–8.64 mg L{sup −1} (tryptamine) and 0.10–8.64 mg L{sup −1} (phenethylamine), whereas accuracy was 97%–102% (recovery test). Detection limit of biogenic amines in wine samples was 0.02–0.03 mg L{sup −1}, whereas quantification limit ranged 0.05–0.10 mg L{sup −1}. The variation coefficients for the analyzed amines ranged between 0.49% and 3.92%. Obtained BA derivatives enhanced separation the analytes on chromatograms due to the inhibition of hydrolysis reaction and the reduction of by-products formation.

New Environmentalconditions Responsible for the amount of mg Incorporated in Biogenic Carbonates

Science.gov (United States)

Zuddas, P.; Cherchi, A.; DeGiudici, G. B.; Buosi, C.

2012-12-01

The composition of carbonate minerals formed in past and present oceans is assumed to be significantly controlled by temperature and seawater composition. Several kinetic laboratory investigations have suggested that the temperature is kinetically responsible for the amount of Mg incorporated in both abiotic and biogenic calcites and that variation of kinetic reaction mechanism resulting from the temperature changes are correlated with the variable amount of Mg incorporated in calcites. These results explain why in present-day marine carbonates low-Mg calcite cements are mainly associated with cool water while high-Mg carbonates are dominantly found in warm-water environments. An apparent inverse relationship between the global average paleo-temperature and the Mg/Ca ratio is however observed in the past formed marine carbonate. This apparent contradiction has been interpreted as resulting from a possible changing in the relative seawater geochemical cycles of these cations. Recent monitoring of costal areas in presence of heavy metals and CO2 released from industrial polluted area reveals the presence of porcelanaceous miliolids infested by microscopic boring microflora (cyanobacteria, algae and fungi). Here, benthonic foraminifera have Mg/Ca molar ratio by one order of magnitude higher when compared to the average value of the same genus living under uncontaminated environments. A similar behaviour has been found for Zn, Cd and Pb. In these contaminated environments, temperature and average major seawater composition remain constant, while PCO2 partial pressure (estimated by pH and alkalinity using the ion pairing model) is 3-5 times higher than the average for the open sea nearby. Geochemical models predicts that CO2 increase is affecting carbonate saturation state of surface water in the twenty-first century indicating that calcareous organisms may have difficulty calcifying leading to production of weaker skeletons and greater vulnerability to erosion. The

Intramedullary Mg2Ag nails augment callus formation during fracture healing in mice.

Science.gov (United States)

Jähn, Katharina; Saito, Hiroaki; Taipaleenmäki, Hanna; Gasser, Andreas; Hort, Norbert; Feyerabend, Frank; Schlüter, Hartmut; Rueger, Johannes M; Lehmann, Wolfgang; Willumeit-Römer, Regine; Hesse, Eric

2016-05-01

Intramedullary stabilization is frequently used to treat long bone fractures. Implants usually remain unless complications arise. Since implant removal can become technically very challenging with the potential to cause further tissue damage, biodegradable materials are emerging as alternative options. Magnesium (Mg)-based biodegradable implants have a controllable degradation rate and good tissue compatibility, which makes them attractive for musculoskeletal research. Here we report for the first time the implantation of intramedullary nails made of an Mg alloy containing 2% silver (Mg2Ag) into intact and fractured femora of mice. Prior in vitro analyses revealed an inhibitory effect of Mg2Ag degradation products on osteoclast differentiation and function with no impair of osteoblast function. In vivo, Mg2Ag implants degraded under non-fracture and fracture conditions within 210days and 133days, respectively. During fracture repair, osteoblast function and subsequent bone formation were enhanced, while osteoclast activity and bone resorption were decreased, leading to an augmented callus formation. We observed a widening of the femoral shaft under steady state and regenerating conditions, which was at least in part due to an uncoupled bone remodeling. However, Mg2Ag implants did not cause any systemic adverse effects. These data suggest that Mg2Ag implants might be promising for intramedullary fixation of long bone fractures, a novel concept that has to be further investigated in future studies. Biodegradable implants are promising alternatives to standard steel or titanium implants to avoid implant removal after fracture healing. We therefore developed an intramedullary nail using a novel biodegradable magnesium-silver-alloy (Mg2Ag) and investigated the in vitro and in vivo effects of the implants on bone remodeling under steady state and fracture healing conditions in mice. Our results demonstrate that intramedullary Mg2Ag nails degrade in vivo over time without

Tem Observation Of Precipitate Structures In Al-Zn-Mg Alloys With Additions Of Cu/Ag

Directory of Open Access Journals (Sweden)

Watanabe K.

2015-06-01

Full Text Available Al-Zn-Mg alloy has been known as one of the aluminum alloys with the good age-hardening ability and the high strength among commercial aluminum alloys. The mechanical property of the limited ductility, however, is required to further improvement. In this work, three alloys, which were added Cu or Ag into the Al-Zn-Mg alloy, were prepared to compare the effect of the additional elements on the aging behavior. The content of Ag and Cu were 0.2at.% and the same as, respectively. Ag or Cu added alloy showed higher maximum hardness than base alloy. The particle shape and rod shape precipitates were observed in all alloys peak-aged at 423K. According to addition of Ag or Cu, the number density of the precipitates increased higher than that of base alloy.

Direct in situ activation of Ag0 nanoparticles in synthesis of Ag/TiO2 and its photoactivity

International Nuclear Information System (INIS)

Jaafar, N.F.; Jalil, A.A.; Triwahyono, S.; Efendi, J.; Mukti, R.R.; Jusoh, R.; Jusoh, N.W.C.; Karim, A.H.; Salleh, N.F.M.; Suendo, V.

2015-01-01

Graphical abstract: - Highlights: • Ag 0 loaded on TiO 2 was prepared by a direct in situ electrochemical method. • 5 wt% Ag–TiO 2 demonstrated the best photocatalytic degradation of 2-CP. • Isomorphous substitution of Ag with Ti occurred to form Ti−O−Ag bonds. • Ag 0 and oxygen vacancies trapped electrons to enhance e–H + separation. • Substitution of Ag in the TiO 2 structure decreased the number of oxygen vacancies. - Abstract: Metallic Ag nanoparticles (Ag 0 ) were successfully activated using a direct in situ electrochemical method before being supported on TiO 2 . Catalytic testing showed that 5 wt% Ag–TiO 2 gave the highest photodegradation (94%) of 50 mg L −1 2-chlorophenol (2-CP) at pH 5 using 0.375 g L −1 catalyst within 6 h, while under similar conditions, 1 wt% and 10 wt% Ag–TiO 2 only gave 75% and 78% degradation, respectively. Characterization results illustrated that the photoactivity was affected by the amount of Ag 0 and oxygen vacancies which act as an electrons trap to enhance the electron–hole separation. While, the Ag−O−Ti bonds formation reduced the photoactivity. The degradation followed a pseudo-first order Langmuir–Hinshelwood model where adsorption was the controlling step. Study on the effect of scavengers showed that the hole (H + ) and hydroxyl radical (OH·) play important roles in the photodegradation. The regenerated photocatalyst was still stable after five cycling runs

Subsurface Synthesis and Characterization of Ag Nanoparticles Embedded in MgO

Energy Technology Data Exchange (ETDEWEB)

Vilayur Ganapathy, Subramanian; Devaraj, Arun; Colby, Robert J.; Pandey, Archana; Varga, Tamas; Shutthanandan, V.; Manandhar, Sandeep; El-Khoury, Patrick Z.; Kayani, Asghar N.; Hess, Wayne P.; Thevuthasan, Suntharampillai

2013-03-08

Metal nanoparticles exhibit localized surface plasmon resonance (LSPR) which is very sensitive to the size and shape of the nanoparticle and the dielectric medium surrounding it. LSPR causes field enhancement near the surface of the nanoparticle making them interesting candidates for plasmonic applications. In particular, partially exposed metallic nanoparticles distributed in a dielectric matrix form hotspots which are prime locations for LSPR spectroscopy and sensing. This study involves synthesizing partially buried Ag nanoparticles in MgO and investigating the characteristics of this material system. Ag nanoparticles of different shapes and size distributions were synthesized below the surface of MgO by implanting 200 keV Ag+ ions followed by annealing at 10000C for 10 and 30 hours. A detailed optical and structural characterization was carried out to understand the evolution of Ag nanoparticle microstructure and size distribution inside the MgO matrix. Micro x-ray diffraction (MicroXRD) was employed to investigate the structural properties and estimate the crystallite size. The nanoparticles evolved from a spherical to faceted morphology with annealing time, assuming an octahedral shape truncated at the (001) planes as seen from aberration corrected transmission electron microscopy (TEM) images. The nanoparticles embedded in MgO were shown to be pure metallic Ag using atom probe tomography (APT). The nanoparticles were partially exposed to the surface employing plasma etch techniques to remove the overlaying MgO. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were employed to study the surface morphology and obtain a height distribution for the partially exposed nanoparticles.

Structural features of AgCaCdMg2(PO4)3 and AgCd2Mg2(PO4)3, two new compounds with the alluaudite-type structure, and their catalytic activity in butan-2-ol conversion

International Nuclear Information System (INIS)

Kacimi, Mohammed; Ziyad, Mahfoud; Hatert, Frederic

2005-01-01

AgCaCdMg 2 (PO 4 ) 3 and AgCd 2 Mg 2 (PO 4 ) 3 , two new compounds with the alluaudite-type structure, were synthesized by a solid state reaction in air at 750 deg. C. The X-ray powder diffraction pattern of AgCaCdMg 2 (PO 4 ) 3 indicates the presence of small amounts of (Ca, Mg) 3 (PO 4 ) 2 with the whitlockite structure, as impurity, whereas AgCd 2 Mg 2 (PO 4 ) 3 is constituted by pure alluaudite. The Rietveld refinements of the X-ray powder diffraction patterns indicate an ordered cationic distribution for AgCd 2 Mg 2 (PO 4 ) 3 , with Ag on A(2)', Cd on A(1) and M(1), and Mg on M(2), whereas a disordered distribution of Cd and Ca between the A(1) and M(1) sites is observed for AgCaCdMg 2 (PO 4 ) 3 . The catalytic properties of these compounds has been measured in reaction of butan-2-ol dehydrogenation. In the absence of oxygen, both samples exhibit poor dehydrogenation activity. All samples displayed no dehydration activity. Introduction of oxygen into the feed changed totally the catalytic behavior of the catalysts. The production of methyl ethyl ketone increases with time on stream and the reaction temperature. AgCaCdMg 2 (PO 4 ) 3 is more efficient than AgCd 2 Mg 2 (PO 4 ) 3

Effects of storage temperature on biogenic amine concentrations in meat of uneviscerated pheasants (Phasianus colchicus

Directory of Open Access Journals (Sweden)

Zdeňka Hutařová

2013-01-01

Full Text Available The aim of this study was to determine the hygienic quality of the pheasants reared for high-quality meat production by the biogenic amine concentrations in their meat. The content of biogenic amines was measured in the meat of sixty male pheasants killed by pithing and stored uneviscerated for 21 days under different storage temperatures (0 °C, 7 °C and 15 °C. The samples of breast and thigh muscles of pheasant were tested at weekly intervals. Biogenic amines were analysed by reverse phase liquid chromatography and detected by tandem mass spectrometry. Concentrations of biogenic amines (except spermin and spermidin in thigh muscle were higher than in breast muscle. Highly significant difference (P < 0.01 was found in tyramine (5.80 mg/kg and 1.38 mg/kg for thigh and breast muscle, respectively, cadaverine (40.80 mg/kg and 14.43 mg/kg for thigh and breast muscle, respectively, putrescine (13.42 mg/kg and 3.16 mg/kg for thigh and breast muscle, respectively and histamine (5.51 mg/kg and 1.70 mg/kg for thigh and breast muscle, respectively concentrations after 21 days of storage at 15 °C. This study provides information on the dynamics of biogenic amine formation in pheasant meat during 21 days of storage at different temperatures. Based on our results, we can recommend storing pithed uneviscerated pheasants at 0–7°C for up to 21 days, or at 15 °C for up to 7 days. Concentrations of biogenic amines gained in our study can be helpful in evaluating freshness and hygienic quality of the pheasant game meat.

Subsurface synthesis and characterization of Ag nanoparticles embedded in MgO

Science.gov (United States)

Vilayurganapathy, S.; Devaraj, A.; Colby, R.; Pandey, A.; Varga, T.; Shutthanandan, V.; Manandhar, S.; El-Khoury, P. Z.; Kayani, Asghar; Hess, W. P.; Thevuthasan, S.

2013-03-01

Metal nanoparticles exhibit a localized surface plasmon resonance (LSPR) which is very sensitive to the size and shape of the nanoparticle and the surrounding dielectric medium. The coupling between the electromagnetic radiation and the localized surface plasmon in metallic nanoparticles results in a sizable enhancement of the incident fields, making them possible candidates for plasmonic applications. In particular, partially exposed metallic nanoparticles distributed in a dielectric matrix can provide prime locations for LSPR spectroscopy and sensing. We report the synthesis and characterization of a plasmonic substrate consisting of Ag nanoparticles partially buried in MgO. Ag nanoparticles of different shapes and size distributions were synthesized below the surface of MgO by implanting 200 keV Ag+ ions followed by annealing at 1000 °C for 10 and 30 h. A detailed optical and structural characterization was carried out to understand the evolution of the Ag nanoparticle and size distribution inside the MgO matrix. Micro x-ray diffraction (Micro-XRD) was employed to investigate the structural properties and estimate the crystallite size. The nanoparticles evolved from a spherical to a faceted morphology with annealing time, assuming an octahedral shape truncated at the (001) planes, as visualized from aberration-corrected transmission electron microscopy (TEM) images. The nanoparticles embedded in MgO were shown to be pure metallic Ag using atom probe tomography (APT). The nanoparticles were partially exposed to the surface by employing plasma etch techniques to remove the overlaying MgO. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were employed to study the surface morphology and obtain a height distribution for the partially exposed nanoparticles.

Subsurface synthesis and characterization of Ag nanoparticles embedded in MgO

International Nuclear Information System (INIS)

Vilayurganapathy, S; Devaraj, A; Colby, R; Pandey, A; Varga, T; Shutthanandan, V; Manandhar, S; Thevuthasan, S; El-Khoury, P Z; Hess, W P; Kayani, Asghar

2013-01-01

Metal nanoparticles exhibit a localized surface plasmon resonance (LSPR) which is very sensitive to the size and shape of the nanoparticle and the surrounding dielectric medium. The coupling between the electromagnetic radiation and the localized surface plasmon in metallic nanoparticles results in a sizable enhancement of the incident fields, making them possible candidates for plasmonic applications. In particular, partially exposed metallic nanoparticles distributed in a dielectric matrix can provide prime locations for LSPR spectroscopy and sensing. We report the synthesis and characterization of a plasmonic substrate consisting of Ag nanoparticles partially buried in MgO. Ag nanoparticles of different shapes and size distributions were synthesized below the surface of MgO by implanting 200 keV Ag + ions followed by annealing at 1000 °C for 10 and 30 h. A detailed optical and structural characterization was carried out to understand the evolution of the Ag nanoparticle and size distribution inside the MgO matrix. Micro x-ray diffraction (Micro-XRD) was employed to investigate the structural properties and estimate the crystallite size. The nanoparticles evolved from a spherical to a faceted morphology with annealing time, assuming an octahedral shape truncated at the (001) planes, as visualized from aberration-corrected transmission electron microscopy (TEM) images. The nanoparticles embedded in MgO were shown to be pure metallic Ag using atom probe tomography (APT). The nanoparticles were partially exposed to the surface by employing plasma etch techniques to remove the overlaying MgO. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were employed to study the surface morphology and obtain a height distribution for the partially exposed nanoparticles. (paper)

Nature of the precipitate in (AgI)0.7(AgPO3)0.3 glass

International Nuclear Information System (INIS)

Kartini, E.; Collins, M.F.

1999-01-01

Complete text of publication follows. Interest of this material arises from its superionic conducting properties, i.e. the conductivity at ambient temperature is a few order of magnitudes larger than in the pure AgI. On quenching the molten miacture from 600 deg C into liquid nitrogen, β-AgI crystal precipitates in the glassy matrix. Neutron powder diffraction studies on (AgI) 0.7 (AgPO 3 ) 0.3 are presented and the powder pattern from the crystalline precipitate is compared with that of pure AgI. The measurements show identical diffraction patterns from the precipitate and from β-AgI with the same lattice parameters. On heating, the precipitate shows a β→α phase transformation at 435 K while AgI shows this transformation at 438 K. At higher temperature in the α phase the powder pattern of the precipitate is again the same as that of pure α-AgI. On cooling the reverse transformation takes place at 415 K and 410 K, respectively. It is concluded that the precipitate is more-or-less pure AgI. (author)

Estimation of Entropy Generation for Ag-MgO/Water Hybrid Nanofluid Flow through Rectangular Minichannel by Using Artificial Neural Network

OpenAIRE

Uysal, Cuneyt; Korkmaz, Mehmet Erdi

2018-01-01

The convective heat transfer andentropy generation characteristics of Ag-MgO/water hybrid nanofluid flowthrough rectangular minichannel were numerically investigated. The Reynoldsnumber was in the range of 200 to 2000 and different nanoparticle volume fractionswere varied between = 0.005 and 0.02. In addition, ArtificialNeural Network was used to create a model for estimating of entropy generationof Ag-MgO/water hybrid nanofluid flow. As a result, it was found th...

Impacts of seawater saturation state (ΩA = 0.4-4.6) and temperature (10, 25 °C) on the dissolution kinetics of whole-shell biogenic carbonates

Science.gov (United States)

Ries, Justin B.; Ghazaleh, Maite N.; Connolly, Brian; Westfield, Isaac; Castillo, Karl D.

2016-11-01

Anthropogenic increase of atmospheric pCO2 since the Industrial Revolution has caused seawater pH to decrease and seawater temperatures to increase-trends that are expected to continue into the foreseeable future. Myriad experimental studies have investigated the impacts of ocean acidification and warming on marine calcifiers' ability to build protective shells and skeletons. No studies, however, have investigated the combined impacts of ocean acidification and warming on the whole-shell dissolution kinetics of biogenic carbonates. Here, we present the results of experiments designed to investigate the effects of seawater saturation state (ΩA = 0.4-4.6) and temperature (10, 25 °C) on gross rates of whole-shell dissolution for ten species of benthic marine calcifiers: the oyster Crassostrea virginica, the ivory barnacle Balanus eburneus, the blue mussel Mytilus edulis, the conch Strombus alatus, the tropical coral Siderastrea siderea, the temperate coral Oculina arbuscula, the hard clam Mercenaria mercenaria, the soft clam Mya arenaria, the branching bryozoan Schizoporella errata, and the coralline red alga Neogoniolithon sp. These experiments confirm that dissolution rates of whole-shell biogenic carbonates decrease with calcium carbonate (CaCO3) saturation state, increase with temperature, and vary predictably with respect to the relative solubility of the calcifiers' polymorph mineralogy [high-Mg calcite (mol% Mg > 4) ≥ aragonite > low-Mg calcite (mol% Mg carbonates. Furthermore, the severity of the temperature effects on gross dissolution rates also varied with respect to carbonate polymorph solubility, with warming (10-25 °C) exerting the greatest effect on biogenic high-Mg calcite, an intermediate effect on biogenic aragonite, and the least effect on biogenic low-Mg calcite. These results indicate that both ocean acidification and warming will lead to increased dissolution of biogenic carbonates in future oceans, with shells/skeletons composed of the more

Influence of silver addition on the microstructure and mechanical properties of squeeze cast Mg-6Al-1Sn-0.3Mn-0.3Ti

International Nuclear Information System (INIS)

Acikgoez, Sehzat; Sevik, Hueseyin; Kurnaz, S.Can

2011-01-01

Graphical abstract: Highlights: → X-ray diffractometry reveals that the main phases are α-Mg, α-Ti, β-Mg 17 Al 12 and Al 8 Mn 5 in the base alloy. → With addition of silver, Al 81 Mn 19 phase was found. → The mechanical properties of the base alloy are improved with addition of silver. → The fracture surface of base alloy shows relatively deeper and more amount of dimples than that of alloys containing silver. - Abstract: In this study, the effect of silver (0, 0.2, 0.5, and 1 wt.%) on the microstructure and mechanical properties of a magnesium-based alloy (Mg-Al 6 wt.%-Sn 1 wt.%-Mn 0.3 wt.%-Ti 0.3 wt.%) were investigated. The alloys were produced under a controlled atmosphere by a squeeze-casting process. X-ray diffractometry revealed that the main phases are α-Mg, α-Ti, β-Mg 17 Al 12 and Al 8 Mn 5 in the all of alloys. In addition to, Al 81 Mn 19 phase was found with Ag additive. Besides, the amount of β-Mg 17 Al 12 phase was decreased with increasing the amount of Ag. The strength of the base alloy was increased by solid solution mechanism and decreasing the amount of β-Mg 17 Al 12 phase with addition of Ag. Furthermore, existence of Al 81 Mn 19 phase can be acted an important role in the increase on the mechanical properties of the alloys.

X-ray absorption study at the Mg and O K edges of ultrathin MgO epilayers on Ag(001)

International Nuclear Information System (INIS)

Luches, P.; D'Addato, S.; Valeri, S.; Groppo, E.; Prestipino, C.; Lamberti, C.; Boscherini, F.

2004-01-01

We determined the local atomic structure of MgO epilayers on Ag(001) by means of polarization-dependent x-ray absorption spectroscopy measurements at the Mg and O K edges. A quantitative analysis of the data in the extended energy range has been performed using multiple scattering simulations. We found that, even in the ultrathin limit, the local structure of the films is rocksalt and we obtained a quantitative evaluation of the average in-plane and out-of-plane film strain at the different thicknesses investigated. An in-plane compressive strain, due to lattice mismatch with the Ag substrate, is clearly present for the 3 ML film. The out-of-plane lattice constant is found to be expanded, in agreement with the expected behavior for a tetragonal distortion of the unit cell. This growth-induced strain is gradually released with increasing thickness and it is almost completely relaxed at 20 ML. Any significant intermixing with the Ag substrate can be ruled out. An expansion of the interplanar distance at the MgO-Ag interface is detected and its sign and magnitude are found to be in agreement with recent ab initio simulations. This work provides previously unavailable input for modeling the physical properties of the system and supports the hypothesis that the different electronic properties of MgO films on Ag(001) are not related to structural or compositional differences at the ultrathin limit

Direct in situ activation of Ag{sup 0} nanoparticles in synthesis of Ag/TiO{sub 2} and its photoactivity

Energy Technology Data Exchange (ETDEWEB)

Jaafar, N.F. [Department of Chemistry, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Jalil, A.A., E-mail: aishah@cheme.utm.my [Institute of Hydrogen Economy, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Department of Chemical Engineering, Faculty of Chemical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Triwahyono, S. [Department of Chemistry, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Ibnu Sina Institute for Fundamental Science Studies, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Efendi, J. [Department of Chemistry, Universitas Negeri Padang, Jl. Prof. Hamka, Air Tawar, Padang, West Sumatera (Indonesia); Mukti, R.R. [Division of Inorganic and Physical Chemistry, Faculty of Mathematics and Natural Science, Institut Teknologi Bandung, Jl Ganesha No. 10, Bandung 40132 (Indonesia); Jusoh, R.; Jusoh, N.W.C. [Department of Chemical Engineering, Faculty of Chemical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Karim, A.H. [Department of Chemistry, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Salleh, N.F.M. [Department of Chemical Engineering, Faculty of Chemical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Suendo, V. [Division of Inorganic and Physical Chemistry, Faculty of Mathematics and Natural Science, Institut Teknologi Bandung, Jl Ganesha No. 10, Bandung 40132 (Indonesia)

2015-05-30

Graphical abstract: - Highlights: • Ag{sup 0} loaded on TiO{sub 2} was prepared by a direct in situ electrochemical method. • 5 wt% Ag–TiO{sub 2} demonstrated the best photocatalytic degradation of 2-CP. • Isomorphous substitution of Ag with Ti occurred to form Ti−O−Ag bonds. • Ag{sup 0} and oxygen vacancies trapped electrons to enhance e–H{sup +} separation. • Substitution of Ag in the TiO{sub 2} structure decreased the number of oxygen vacancies. - Abstract: Metallic Ag nanoparticles (Ag{sup 0}) were successfully activated using a direct in situ electrochemical method before being supported on TiO{sub 2}. Catalytic testing showed that 5 wt% Ag–TiO{sub 2} gave the highest photodegradation (94%) of 50 mg L{sup −1} 2-chlorophenol (2-CP) at pH 5 using 0.375 g L{sup −1} catalyst within 6 h, while under similar conditions, 1 wt% and 10 wt% Ag–TiO{sub 2} only gave 75% and 78% degradation, respectively. Characterization results illustrated that the photoactivity was affected by the amount of Ag{sup 0} and oxygen vacancies which act as an electrons trap to enhance the electron–hole separation. While, the Ag−O−Ti bonds formation reduced the photoactivity. The degradation followed a pseudo-first order Langmuir–Hinshelwood model where adsorption was the controlling step. Study on the effect of scavengers showed that the hole (H{sup +}) and hydroxyl radical (OH·) play important roles in the photodegradation. The regenerated photocatalyst was still stable after five cycling runs.

AgBr/MgBi2O6 heterostructured composites with highly efficient visible-light-driven photocatalytic activity

Science.gov (United States)

Zhong, Liansheng; Hu, Chaohao; Zhuang, Jing; Zhong, Yan; Wang, Dianhui; Zhou, Huaiying

2018-06-01

AgBr/MgBi2O6 heterostructured photocatalysts were synthesized by the deposition-precipitation method. X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL), and UV-Visible diffuse reflectance spectroscopy (UV-Vis DRS) were employed to examine the phase structure, morphology and optical properties of the as-prepared samples. The photocatalytic activity was investigated by decomposing methylene blue (MB) solution under visible light irradiation (λ > 420 nm). AgBr/MgBi2O6 composites exhibited significantly enhanced visible-light-driven photocatalytic properties in comparison with pure MgBi2O6 and AgBr. When the molar ratio of AgBr to MgBi2O6 was 3:1, the composite catalyst showed the optimal photocatalytic activity and excellent stability. The enhanced photocatalytic activity of AgBr/MgBi2O6 composites was attributed to the formation of p-n heterojunction between AgBr and MgBi2O6, thereby resulting in the effective separation and transfer of photogenerated electrons-hole pairs.

Diclofenac and 2‐anilinophenylacetate degradation by combined activity of biogenic manganese oxides and silver

Science.gov (United States)

Meerburg, Francis; Hennebel, Tom; Vanhaecke, Lynn; Verstraete, Willy; Boon, Nico

2012-01-01

Summary The occurrence of a range of recalcitrant organic micropollutants in our aquatic environment has led to the development of various tertiary wastewater treatment methods. In this study, biogenic manganese oxides (Bio‐MnOx), biogenic silver nanoparticles (Bio‐Ag0) and ionic silver were used for the oxidative removal of the frequently encountered drug diclofenac and its dechlorinated form, 2‐anilinophenylacetate (APA). Diclofenac was rapidly degraded during ongoing manganese oxidation by Pseudomonas putida MnB6. Furthermore, whereas preoxidized Bio‐MnOx, Bio‐Ag0 and Ag+ separately did not show any removal capacity for diclofenac, an enhanced removal occurred when Bio‐MnOx and silver species were combined. Similar results were obtained for APA. Finally, a slow removal of diclofenac but more rapid APA degradation was observed when silver was added to manganese‐free P. putida biomass. Combining these results, three mechanisms of diclofenac and APA removal could be distinguished: (i) a co‐metabolic removal during active Mn2+ oxidation by P. putida; (ii) a synergistic interaction between preoxidized Bio‐MnOx and silver species; and (iii) a (bio)chemical process by biomass enriched with silver catalysts. This paper demonstrates the use of P. putida for water treatment purposes and is the first report of the application of silver combined with biogenic manganese for the removal of organic water contaminants. PMID:22221449

Structure determination of AgPO3 and (AgPO3)0.5(AgI)0.5 glasses by neutron diffraction and small angle neutron scattering

International Nuclear Information System (INIS)

Tachez, M.; Mercier, R.; Malugani, J.P.; Chieux, P.

1987-01-01

Neutron diffraction and small angle neutron scattering (SANS) were performed on AgPO 3 and (AgPO 3 ) 0.5 (AgI) 0.5 glasses. AgPO 3 glass is made up of long chains of PO 4 tetrahedra joined together by Ag atoms. When silver iodide is added, the radial distribution function shows a large peak at 2.83 A, due to Ag-I interactions. AgI does not modify the network forming unit. The existence of small clusters is confirmed by analysing the coordination number of Ag-I pairs obtained by subtracting the experimental structure function of the AgPO 3 glass from that of the corresponding AgI-doped glasses. A rough estimation of their size is given by SANS experiments. Not all the AgI pairs are involved in AgI cluster units. The compatibility of the results obtained with recent structural investigations by non diffractometric techniques is examined. 23 refs.; 5 figs.; 3 tabs

Production of biogenic amines in "Salamini italiani alla cacciatora PDO".

Science.gov (United States)

Coı X0308 Sson, Jean Daniel; Cerutti, Caterina; Travaglia, Fabiano; Arlorio, Marco

2004-06-01

Various fermented and seasoned foods such as cheese, sauerkraut, wine, beer and meat products may contain biogenic amines. The aim of this paper was to describe the presence of some biogenic amines (histamine, tyramine, tryptamine, 2-phenylethylamine) in "Salamini italiani alla cacciatora PDO", a typical fermented-ripened dry sausage widely consumed in Italy. Total level of biogenic amines in commercial samples ranged from 71 to 586 mg kg(-1). The amine recovered in higher concentrations was tyramine (372 mg kg(-1)) followed by histamine (165 mg kg(-1)). The second aim of this work was the quality control of the production in order to determine the parameters influencing the presence of biogenic amines in ripened salami. Sausages sampled for analysis during production, manipulation and ripening showed the presence of tyramine (64.4 mg kg(-1)) only after 15 days of fermentation. All investigated biogenic amines were detected in "Salamini" after 21 days of fermentation. We suggest the control of biogenic as important tool to establish the better condition of preservation of "Salamini italiani alla cacciatore PDO" during their shelf-life.

Characterization of Al-Cu-Mg-Ag Alloy RX226-T8 Plate

Science.gov (United States)

Lach, Cynthia L.; Domack, Marcia S.

2003-01-01

aircraft wing and fuselage skin materials through the addition of silver to Al-Cu-Mg alloys based on Al 2519 chemistry [2]. Thermal stability of the resulting Al-Cu-Mg-Ag alloys, C415-T8 and C416-T8, was due to co-precipitation of the thermally stable . (AlCu) and ' (Al2Cu) strengthening phases [1-4]. The strength and toughness behavior was investigated for these alloys produced as 0.090-inch thick rolled sheet in the T8 condition and after various thermal exposures. The mechanical properties were shown to be competitive with conventional aircraft alloys, 2519-T8 and 2618-T8 [2]. During the Integral Airframe Structure (IAS) program, advanced aluminum alloys were examined for use in an integrally stiffened airframe structure where the skin and stiffeners would be machined from plate and extruded frames would be mechanically attached (see Figure 1) [5]. Advantages of integrally stiffened structure include reduced part count, and reduced assembly times compared to conventional built-up airframe structure. The near-surface properties of a thick plate are of significance for a machined integrally stiffened airframe structure since this represents the skin location. Properties measured at the mid-plane of the plate are more representative of the stiffener web. RX226 was developed to exploit strength-toughness improvements and thermal stability benefits of Al-Cu-Mg-Ag alloys in plate gages. This study evaluated the microstructure and properties of three gages of plate produced in the T8 condition.

Microstructure and magnetic properties of nanocomposite FePt/MgO and FePt/Ag films

International Nuclear Information System (INIS)

Chen, S.C.; Kuo, P.C.; Sun, A.C.; Chou, C.Y.; Fang, Y.H.; Wu, T.H.

2006-01-01

An in-plane magnetic anisotropy of FePt film is obtained in the MgO 5 nm/FePt t nm/MgO 5 nm films (where t=5, 10 and 20 nm). Both the in-plane coercivity (H c- parallel ) and the perpendicular magnetic anisotropy of FePt films are increased when introducing an Ag-capped layer instead of MgO-capped layer. An in-plane coercivity is 3154 Oe for the MgO 5 nm/FePt 10 nm/MgO 5 nm film, and it can be increased to 4846 Oe as a 5 nm Ag-capped layer instead of MgO-capped layer. The transmission electron microscopy (TEM)-energy disperse spectrum (EDS) analysis shows that the Ag mainly distributed at the grain boundary of FePt, that leads the increase of the grain boundary energy, which will enhance coercivity and perpendicular magnetic anisotropy of FePt film

An Electrochemical Framework to Explain Intergranular Stress Corrosion Cracking in an Al-5.4%Cu-0.5%Mg-0.5%Ag Alloy

Science.gov (United States)

Little, D. A.; Connolly, B. J.; Scully, J. R.

2001-01-01

A modified version of the Cu-depletion electrochemical framework was used to explain the metallurgical factor creating intergranular stress corrosion cracking susceptibility in an aged Al-Cu-Mg-Ag alloy, C416. This framework was also used to explain the increased resistance to intergranular stress corrosion cracking in the overaged temper. Susceptibility in the under aged and T8 condition is consistent with the grain boundary Cu-depletion mechanism. Improvements in resistance of the T8+ thermal exposure of 5000 h at 225 F (T8+) compared to the T8 condition can be explained by depletion of Cu from solid solution.

Investigation of modulus hardening of various co-clusters in aged Al-Cu-Mg-Ag alloy by atom probe tomography

Energy Technology Data Exchange (ETDEWEB)

Bai, Song [Key Laboratory of Nonferrous Metal Materials Science and Engineering, Ministry of Education, Central South University, Changsha 410083 (China); School of Material Science and Engineering, Central South University, Changsha 410083 (China); Liu, Zhiyi, E-mail: liuzhiyi@csu.edu.cn [Key Laboratory of Nonferrous Metal Materials Science and Engineering, Ministry of Education, Central South University, Changsha 410083 (China); School of Material Science and Engineering, Central South University, Changsha 410083 (China); Ying, Puyou; Wang, Jian; Li, Junlin [Key Laboratory of Nonferrous Metal Materials Science and Engineering, Ministry of Education, Central South University, Changsha 410083 (China); School of Material Science and Engineering, Central South University, Changsha 410083 (China)

2016-06-21

The modulus hardening capability of various co-clusters in a low Cu/Mg ratio Al-Cu-Mg-Ag alloy aged at 165 °C is investigated by quantitative atom probe tomography analysis. Prolonged aging from 5 min to 2 h leads to the simultaneous increase in the critical shear stress of both Mg-Ag and Cu-Mg co-clusters. Regardless of the higher shear modulus of Cu-Mg co-clusters, calculation results show that Mg-Ag co-clusters possess a greater modulus hardening capability than Cu-Mg co-clusters, suggesting its primary contribution to the rapid hardening at the early aging stage. As aging extends from 30 min to 2 h, the increment in the critical shear stress of Mg-Ag co-clusters is lower than that of Cu-Mg co-clusters due to the precipitation of high density Ω phase. In addition, the shear modulus of Mg-Ag co-clusters is generally independent on its size at each investigated condition.

Investigation of modulus hardening of various co-clusters in aged Al-Cu-Mg-Ag alloy by atom probe tomography

International Nuclear Information System (INIS)

Bai, Song; Liu, Zhiyi; Ying, Puyou; Wang, Jian; Li, Junlin

2016-01-01

The modulus hardening capability of various co-clusters in a low Cu/Mg ratio Al-Cu-Mg-Ag alloy aged at 165 °C is investigated by quantitative atom probe tomography analysis. Prolonged aging from 5 min to 2 h leads to the simultaneous increase in the critical shear stress of both Mg-Ag and Cu-Mg co-clusters. Regardless of the higher shear modulus of Cu-Mg co-clusters, calculation results show that Mg-Ag co-clusters possess a greater modulus hardening capability than Cu-Mg co-clusters, suggesting its primary contribution to the rapid hardening at the early aging stage. As aging extends from 30 min to 2 h, the increment in the critical shear stress of Mg-Ag co-clusters is lower than that of Cu-Mg co-clusters due to the precipitation of high density Ω phase. In addition, the shear modulus of Mg-Ag co-clusters is generally independent on its size at each investigated condition.

Effect of storage conditions on the biogenic amine content in wild boar meat

Directory of Open Access Journals (Sweden)

Zdeňka Hutařová

2014-01-01

Full Text Available Hygienic quality of game meat depends on many factors during and after hunting. Freshness of meat is connected with the concentration of biogenic amines which is related to meat spoilage. The aim of this study was to assess changes in concentration of biogenic amines in raw meat of wild boar (n = 20, mean age 1–2 years during storage at different temperatures. Carcases of wild boars hunted in winter 2012 in hunting districts of south Moravia were stored unskinned during 21 days at various temperatures (0, 7 and 15 °C. Concentrations of biogenic amines (putrescine, cadaverine, tyramine, tryptamine, phenylethylamine, histamine, spermine and spermidine were determined in the shoulder and leg muscles by high-performance liquid chromatography in combination with triple quadrupole tandem mass spectrometry. Good hygienic quality was maintained when wild boar carcasses were stored for a maximum of 14 days at 0 °C (content of biogenic amines in 3 meat samples exceed the limit of 5 mg/kg on day 21 of storage or a maximum of 7 days at 7 °C (content of biogenic amines in 4 meat samples exceed the limit of 5 mg/kg on day 14 of storage. The temperature of 15 °C should be considered as unsuitable storage temperature if good hygienic quality of game meat during storage is to be guaranteed (content of biogenic amines in 2 meat samples exceed the limit of 5 mg/kg already on day 7 of storage. The study brings new information about the biogenic amine content and its changes in wild boar meat during the storage period of 21 days.

Coincidence Doppler broadening and 3DAP study of the pre-precipitation stage of an Al-Li-Cu-Mg-Ag alloy

International Nuclear Information System (INIS)

Honma, T.; Yanagita, S.; Hono, K.; Nagai, Y.; Hasegawa, M.

2004-01-01

Pre-precipitation solute clustering in Al-Li-Cu-Mg-Ag and Al-Cu-Mg-Ag alloys has been investigated by coincidence Doppler broadening (CDB) spectroscopy of positron annihilation and three-dimensional atom probe (3DAP) analysis. Although Ag-Mg co-clusters form in the Al-Cu-Mg-Ag alloy in the early stage of aging, no evidence for the co-cluster formation was obtained from the Li containing alloy using 3DAP. While CDB spectra indicated that vacancies are associated with Ag after aging for 15 s in the Al-Cu-Mg-Ag alloy, vacancy-Ag association is suppressed in the Li containing alloy. Based on the 3DAP and CDB results, the reasons for the completely different clustering behaviors observed in these two similar alloys are discussed

BIOGENIC AMINES CONTENT IN DIFFERENT WINE SAMPLES

Directory of Open Access Journals (Sweden)

Attila Kántor

2015-02-01

Full Text Available Twenty-five samples of different Slovak wines before and after filtration were analysed in order to determine the content of eight biogenic amines (tryptamine, phenylalanine, putrescine, cadaverine, histamine, tyramine, spermidine and spermine. The method involves extraction of biogenic amines from wine samples with used dansyl chloride. Ultra-high performance liquid chromatography (UHPLC was used for determination of biogenic amines equipped with a Rapid Resolution High Definition (RRHD, DAD detectors and Extend-C18 LC column (50 mm x 3.0 mm ID, 1.8 μm particle size. In this study the highest level of biogenic amine in all wine samples represent tryptamine (TRM with the highest content 170.9±5.3 mg/L in Pinot Blanc wine. Phenylalanine (PHE cadaverine (CAD, histamine (HIS and spermidine (SPD were not detected in all wines; mainly SPD was not detected in 16 wines, HIS not detected in 14 wines, PHE and CAD not detected in 2 wines. Tyramine (TYR, spermine (SPN and putrescine (PUT were detected in all wines, but PUT and SPN in very low concentration. The worst wine samples with high biogenic amine content were Saint Laurent (BF, Pinot Blanc (S and Pinot Noir (AF.

Microstructure-property relationships in Al-Cu-Li-Ag-Mg Weldalite (tm) alloys, part 2

Science.gov (United States)

Langan, T. J.; Pickens, J. R.

1991-01-01

The microstructure and mechanical properties of the ultrahigh strength Al-Cu-Li-Ag-Mg alloy, Weldalite (tm) 049, were studied. Specifically, the microstructural features along with tensile strength, weldability, Young's modulus and fracture toughness were studied for Weldalite (tm) 049 type alloys with Li contents ranging from 1.3 to 1.9 wt. pct. The tensile properties of Weldalite 049 and Weldalite 049 reinforced with TiB2 particles fabricated using the XD (tm) process were also evaluated at cryogenic, room, and elevated temperatures. In addition, an experimental alloy, similar in composition to Weldalite 049 but without the Ag+Mg, was fabricated. The microstructure of this alloy was compared with that of Weldalite 049 in the T6 condition to assess the effect of Ag+Mg on nucleation of strengthening phases in the absence of cold work.

Microstructure and mechanical properties of Al-Cu-Mg-Mn-Zr alloy with trace amounts of Ag

International Nuclear Information System (INIS)

Liu Xiaoyan; Pan Qinglin; Lu Congge; He Yunbin; Li Wenbin; Liang Wenjie

2009-01-01

The microstructure and mechanical properties of Al-Cu-Mg-(Ag)-Mn-Zr alloys were studied by means of tensile testing, optical microscopy (OM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that small additions of Ag to Al-Cu-Mg-Mn-Zr alloy can accelerate the hardening effect of the aged alloy and reduce the time to peak-aged. The mechanical properties can be improved both at room temperature and at elevated temperatures, which is attributed to the fine and uniform plate-like Ω precipitates. Meanwhile the ductility of the studied alloys remains at relatively high level. The major strengthening phases of the Ag-free alloy are θ' and less S', while that of Al-Cu-Mg-Mn-Zr alloy containing trace amounts of Ag are Ω and less θ'.

Biogenic amine content, histamine-forming bacteria, and adulteration of pork in tuna sausage products.

Science.gov (United States)

Kung, Hsien-Feng; Tsai, Yung-Hsiang; Chang, Shih-Chih; Hong, Tang-Yao

2012-10-01

Twenty-five tuna sausage products were purchased from retail markets in Taiwan. The rates of occurrence of biogenic amines, histamine-forming bacteria, and adulteration by pork and poultry were determined. The average content of various biogenic amines in all tested samples was less than 2.0 mg/100 g (Makaira nigricans (blue marlin).

Photocatalytic oxidation removal of Hg"0 using ternary Ag/AgI-Ag_2CO_3 hybrids in wet scrubbing process under fluorescent light

International Nuclear Information System (INIS)

Zhang, Anchao; Zhang, Lixiang; Chen, Xiaozhuan; Zhu, Qifeng; Liu, Zhichao; Xiang, Jun

2017-01-01

Highlights: • Ag/AgI-Ag_2CO_3 hybrids were employed for Hg"0 removal under fluorescent light. • Superoxide radical (·O_2"−) played a key role in Hg"0 removal. • NO exhibited a significant effect on Hg"0 removal in comparison to SO_2. • The mechanism for enhanced Hg"0 removal over Ag/AgI-Ag_2CO_3 was proposed. - Abstract: A series of ternary Ag/AgI-Ag_2CO_3 photocatalysts synthesized using a facile coprecipitation method were employed to investigate their performances of Hg"0 removal in a wet scrubbing reactor. The hybrids were characterized by N_2 adsorption-desorption, XRD, SEM-EDS, HRTEM, XPS, DRS and ESR. The photocatalytic activities of Hg"0 removal were evaluated under fluorescent light. The results showed that AgI content, fluorescent light irradiation, reaction temperature all showed significant influences on Hg"0 removal. NO exhibited significant effect on Hg"0 removal in comparison to SO_2. Among these ternary Ag/AgI-Ag_2CO_3 hybrids, Ag/AgI(0.1)-Ag_2CO_3 showed the highest Hg"0 removal efficiency, which could be ascribed to the effective separation of photogenerated electron-hole pairs between AgI and Ag_2CO_3 and the surface plasmon resonance (SPR) effect in the visible region by metallic silver nanoparticles (Ag"0 NPs). The trapping studies of reactive radicals showed that the superoxide radicals (·O_2"−) may play a key role in Hg"0 removal under fluorescent light. According to the experimental and characterization results, a possible photocatalytic oxidation mechanism for enhanced Hg"0 removal over Ag/AgI(0.1)-Ag_2CO_3 hybrid under fluorescent light was proposed.

Influence of Mn on the tensile properties of SSM-HPDC Al-Cu-Mg-Ag alloy A201

CSIR Research Space (South Africa)

Müller, H

2011-03-01

Full Text Available A201 aluminium alloy is a high strength casting alloy with a nominal composition of Al-4.6Cu-0.3Mg-0.6Ag. It is strengthened by the O(Al2Cu) phase and the ’(Al2Cu) phase during heat treatment. Further strengthening of this alloy system can...

The impact of drawing on the biogenic amines content in meat of pithed pheasant

Directory of Open Access Journals (Sweden)

Zdeňka Hutařová

2013-01-01

Full Text Available With the increasing popularity of game meat, greater emphasis is being placed on ensuring high hygienic quality of this food. Biogenic amines are among possible indicators of the hygienic quality of meat. The aim of this study was to monitor biogenic amine concentrations in the muscle tissues of pheasants (n = 20 killed by pithing and treated by drawing (guts are removed from the body cavity through the cloaca using a specially fashioned hook. The pheasants’ bodies were stored hanged by the neck for 21 days at ±7 °C. Breast and thigh muscle samples were collected at weekly intervals (day 1, 7, 14 and 21 of storage. Biogenic amines (putrescine, cadaverine, tyramine, histamine, tryptamine and phenylethylamine were analysed by reverse phase liquid chromatography and detected by tandem mass spectrometry. In breast muscle, the most evident change was noted in the concentration of cadaverine (0.026 and 1.070 mg/kg for storage day 1 and 21, respectively and tyramine (0.001 and 0.958 mg/kg for storage day 1 and 21, respectively. Throughout the storage period, the concentration of 5 mg/kg (indicating a loss of high hygienic quality of meat was not exceeded by any of the assessed biogenic amines. In thigh muscle, the concentration indicating high hygienic quality of meat was exceed after 14 days of storage in the case of cadaverine, tyramine and putrescine (at the end of storage their concentrations were 9.058, 10.708 and 3.345 mg/kg, respectively. Hygienic quality of thigh muscle decreased faster compared to breast muscle. This study brings new information about the content of biogenic amines in the meat of pithed pheasants treated by drawing.

In vivo and in vitro degradation comparison of pure Mg, Mg-10Gd and Mg-2Ag: a short term study

Directory of Open Access Journals (Sweden)

I Marco

2017-02-01

Full Text Available The purpose of this study was to compare short term in vitro and in vivo biodegradation studies with low purity Mg (> 99.94 %, Mg-10Gd and Mg-2Ag designed for biodegradable implant applications. Three in vitro testing conditions were applied, using (i phosphate buffered saline (PBS, (ii Hank’s balanced salt solution (HBSS and (iii Dulbecco’s modified eagle medium (DMEM in 5 % CO2 under sterile conditions. Gas evolution and mass loss (ML were assessed, as well as the degradation layer, by elemental mapping and scanning electron microscopy (SEM. In vivo, implantations were performed on male Sprague-Dawley rats evaluating both, gas cavity volume and implant volume reduction by micro-computed tomography (µCT, 7 d after implantation. Samples were produced by casting, solution heat treatment and extrusion in disc and pin shape for the in vitro and in vivo experiments, respectively. Results showed that when the processing of the Mg sample varied, differences were found not only in the alloy impurity content and the grain size, but also in the corrosion behaviour. An increase of Fe and Ni or a large grain size seemed to play a major role in the degradation process, while the influence of alloying elements, such as Gd and Ag, played a secondary role. Results also indicated that cell culture conditions induced degradation rates and degradation layer elemental composition comparable to in vivo conditions. These in vitro and in vivo degradation layers consisted of Mg hydroxide, Mg-Ca carbonate and Ca phosphate.

Anisotropic Mg Electrodeposition and Alloying with Ag-based Anodes from Non-Coordinating Mixed-Metal Borohydride Electrolytes for Mg Hybrid Batteries

International Nuclear Information System (INIS)

Wetzel, David J.; Malone, Marvin A.; Gewirth, Andrew A.; Nuzzo, Ralph G.

2017-01-01

A highly anisotropic electrodeposition was observed using the hybrid battery electrolyte Mg(BH 4 ) 2 with LiBH 4 in diglyme. At low overpotentials high aspect ratio platelet morphologies are observed with a strong fiber texture composed of a {10-10} and a {11-20} component, the first evidence of behavior of this kind in magnesium battery electrolytes. At high overpotentials the deposit aspect ratio is indistinguishable but the texture is shown to be primarily composed of a {11-20} fiber texture. The kinetic parameters relative to the relevant crystallographic faces are extracted from electron microscopy images and compared with the observed bulk rate extracted from the electrochemical data. The use of polycrystalline Ag foil substrates with little preferred orientation at the surface allowed highly polycrystalline nucleation at lower overpotentials than that of platinum, likely due to Ag alloying with Mg. Characterization using focused ion beam (FIB) cross-sections with Auger Electron Spectroscopy (AES) elemental analysis confirm that the deposits are primarily Mg although Mg‐Ag alloys of various compositions were observed. It is proposed that the orientation at slow rates of growth is due to the underlying kinetics of adatom diffusion on Mg and that higher rates diminish the phenomenon due to decreased time for adatom diffusion and instead are governed by the rates of adatom formation or more specifically the adatom vacancy formation on the different low-index planes of Mg.

Study of Ag+/PAA (polyacrylic acid) and Ag0/PAA aqueous system at equilibrium

International Nuclear Information System (INIS)

Keghouche, N.; Mostafavi, M.; Delcourt, M.O.

1991-01-01

When submitted to gamma radiation the system Ag + -PAA-water leads to clusters Ag 0 n /PAA (3 420 nm) interacting with the clusters. Potentiometric measurements carried out on Ag + solutions in the presence of PAA at various pH show that the deprotonated form (polyacrylate anion) is strongly bonded to Ag + , on the opposite of the protonated form of PAA. One of the oligomer clusters can be stabilized for more than one year. Studying it by infra-red spectrometry reveals important modifications in the vibration bands of the COO - group circa 1400 and 1600 cm -1 according to the bonding of PAA with Ag + or Ag 0 [fr

Insulator at the ultrathin limit: MgO on Ag(001).

Science.gov (United States)

Schintke, S; Messerli, S; Pivetta, M; Patthey, F; Libioulle, L; Stengel, M; De Vita, A; Schneider, W D

2001-12-31

The electronic structure and morphology of ultrathin MgO films epitaxially grown on Ag(001) were investigated using low-temperature scanning tunneling spectroscopy and scanning tunneling microscopy. Layer-resolved differential conductance (dI/dU) measurements reveal that, even at a film thickness of three monolayers, a band gap of about 6 eV is formed corresponding to that of the MgO(001) single-crystal surface. This finding is confirmed by layer-resolved calculations of the local density of states based on density functional theory.

Composition and properties tailoring in Mg.sup.2+./sup. codoped non-stoichiometric LuAG:Ce,Mg scintillation ceramics

Czech Academy of Sciences Publication Activity Database

Liu, S.; Mareš, Jiří A.; Babin, Vladimir; Hu, C.; Kou, H.; D'Ambrosio, C.; Li, J.; Pan, Y.; Nikl, Martin

2017-01-01

Roč. 37, č. 4 (2017), s. 1689-1694 ISSN 0955-2219 R&D Projects: GA ČR GA16-15569S Institutional support: RVO:68378271 Keywords : non-stoichiometric ceramic s * LuAG:Ce * Mg scintillator * Mg 2+ codopant * antisite defects * afterglow Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 3.411, year: 2016

Biogenic amine formation and bacterial contribution in Natto products.

Science.gov (United States)

Kim, Bitna; Byun, Bo Young; Mah, Jae-Hyung

2012-12-01

Twenty-one Natto products currently distributed in Korea were analysed for biogenic amine contents and tested to determine physicochemical and bacterial contributions to biogenic amine formation. Among them, nine products (about 43%) had β-phenylethylamine or tyramine contents greater than the toxic dose (30mg/kg and 100mg/kg, respectively) of each amine, although no products showed total amounts of biogenic amines above the harmful level (1000mg/kg), which indicates that the amounts of biogenic amines in some Natto products are not within the safe level for human health. From four different Natto products, that contained noticeable levels of β-phenylethylamine and tyramine, 80 bacterial strains were isolated. All the strains were identified to be Bacillus subtilis and highly capable of producing β-phenylethylamine and tyramine. Therefore, it seems likely that the remarkable contents of β-phenylethylamine and tyramine in Natto predominantly resulted from the strains highly capable of producing those amines present in the food. Copyright © 2012 Elsevier Ltd. All rights reserved.

Ab initio transmission electron microscopy image simulations of coherent Ag-MgO interfaces

International Nuclear Information System (INIS)

Mogck, S.; Kooi, B.J.; Hosson, J.Th.M. de; Finnis, M.W.

2004-01-01

Density-functional theory calculations, within the plane-wave-ultrasoft pseudopotential framework, were performed in the projection for MgO and for the coherent (111) Ag-MgO polar interface. First-principles calculations were incorporated in high-resolution transmission electron microscopy (HRTEM) simulations by converting the charge density into electron scattering factors to examine the influence of charge transfer, charge redistribution at the interface, and ionicity on the dynamical electron scattering and on calculated HRTEM images. It is concluded that the ionicity of oxides and the charge redistribution at interfaces play a significant role in HRTEM image simulations. In particular, the calculations show that at oxygen-terminated (111) Ag-MgO interfaces the first oxygen layer at the interface is much brighter than that in calculations with neutral atoms, in agreement with experimental observations

Ag-loaded MgSrFe-layered double hydroxide/chitosan composite scaffold with enhanced osteogenic and antibacterial property for bone engineering tissue.

Science.gov (United States)

Cao, Dandan; Xu, Zhengliang; Chen, Yixuan; Ke, Qinfei; Zhang, Changqing; Guo, Yaping

2018-02-01

Bone tissue engineering scaffolds for the reconstruction of large bone defects should simultaneously promote osteogenic differentiation and avoid postoperative infection. Herein, we develop, for the first time, Ag-loaded MgSrFe-layered double hydroxide/chitosan (Ag-MgSrFe/CS) composite scaffold. This scaffold exhibits three-dimensional interconnected macroporous structure with a pore size of 100-300 μm. The layered double hydroxide nanoplates in the Ag-MgSrFe/CS show lateral sizes of 200-400 nm and thicknesses of ∼50 nm, and the Ag nanoparticles with particle sizes of ∼20 nm are uniformly dispersed on the scaffold surfaces. Human bone marrow-derived mesenchymal stem cells (hBMSCs) present good adhesion, spreading, and proliferation on the Ag-MgSrFe/CS composite scaffold, suggesting that the Ag and Sr elements in the composite scaffold have no toxicity to hBMSCs. When compared with MgFe/CS composite scaffold, the Ag-MgSrFe/CS composite scaffold has better osteogenic property. The released Sr 2+ ions from the composite scaffold enhance the alkaline phosphatase activity of hBMSCs, promote the extracellular matrix mineralization, and increase the expression levels of osteogenic-related RUNX2 and BMP-2. Moreover, the Ag-MgSrFe/CS composite scaffold possesses good antibacterial property because the Ag nanoparticles in the composite scaffold effectively prevent biofilm formation against S. aureus. Hence, the Ag-MgSrFe/CS composite scaffold with excellent osteoinductivity and antibacterial property has a great potential for bone tissue engineering. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 863-873, 2018. © 2017 Wiley Periodicals, Inc.

High magnetic coercivity of FePt-Ag/MgO granular nanolayers

Science.gov (United States)

Roghani, R.; Sebt, S. A.; Khajehnezhad, A.

2018-06-01

L10-FePt ferromagnetic nanoparticles have a hight coercivity of Tesla order. Thus, these nanoparticles, with size of 10 to 15 nm and uniform surface distribution, are suitable in magnetic data storage technology with density of more than 1GB. In order to improve structural and magnetic properties of FePt nanoparticles, some elements and combinations have been added to compound. In this research, we show that due to the presence of the Ag, the phase transition temperature of FePt from fcc to L10-fct phase decreases. The presence of Ag as an additive in FePt-Ag nanocomposite, increases the magnetic coercivity. This nanocomposite, with 10% Ag, was deposited by magnetron sputtering on the MgO heat layer. VSM results of 10 nm nanoparticles show that coercivity has increased up to 1.4 T. XRD and FESEM results confirm that the size of the L10-FePt nanoparticles are 10 nm and their surface distribution are uniform. Ag gradually form nano scale clusters with separate lattice and FePt-Ag nanocomposite appears. The result of this process is emptiness of Ag position in FePt-fcc lattice. So, the mobility of Fe and Pt atoms in this lattice increases and it can be possible for them to move in lower temperature. This mechanism explain the effect of Ag on decreasing the transition temperature to fct-L10 phase, and hight coercivity of FePt nanoparticles.

The coordination of sulfur in synthetic and biogenic Mg calcites: The red coral case

Science.gov (United States)

Perrin, J.; Rivard, C.; Vielzeuf, D.; Laporte, D.; Fonquernie, C.; Ricolleau, A.; Cotte, M.; Floquet, N.

2017-01-01

Sulfur has been recognized in biogenic calcites for a long time. However, its structural position is matter of debate. For some authors, sulfur is a marker of the organic matrix while it is part of the calcite structure itself for others. To better understand the place of sulfur in calcite, sulfated magnesian calcites (S-MgCalcite) have been synthetized at high pressure and temperature and studied by μ-XANES spectroscopy. S-MgCalcite XANES spectra show two different types of sulfur: sulfate (SO42-) as a predominant species and a small contribution of sulfite (SO32-), both substituting for carbonate ions in the calcite structure. To address the question of the position of sulfur in biogenic calcites, the oxidation states of sulfur in the skeleton and organic tissues of Corallium rubrum have been investigated by micro X-ray fluorescence (μ-XRF) and sulfur K-edge micro X-ray absorption near edge structure (μ-XANES) spectroscopy at the European Synchrotron Radiation Facility (ESRF, Grenoble, France) on beamline ID21. In the skeleton, sulfur is mainly present as oxidized sulfur SO42- (+VI), plus a weak sulfite contribution. XANES spectra indicate that sulfur is inorganically incorporated as sulfur structurally substituted to carbonate ions (SSS). Although an organic matrix is present in the red coral skeleton, reduced organic sulfur could not be detected by μ-XANES spectroscopy in the skeleton probably due to low organic/inorganic sulfur ratio. In the organic tissues surrounding the skeleton, several sulfur oxidation states have been detected including disulfide (S-S), thioether (R-S-CH3), sulfoxide (SO2), sulfonate (SO2O-) and sulfate (SO42-). The unexpected occurrence of inorganic sulfate within the organic tissues suggests the presence of pre-organized organic/inorganic complexes in the circulatory system of the red coral, precursors to biomineralization ahead of the growth front.

Stress-induced thickening of Ω phase in Al–Cu–Mg alloys containing various Ag additions

Energy Technology Data Exchange (ETDEWEB)

Bai, Song [Key Laboratory of Nonferrous Metal Materials Science and Engineering, Ministry of Education, Central South University, Changsha 410083 (China); School of Material Science and Engineering, Central South University, Changsha 410083 (China); Liu, Zhiyi, E-mail: liuzhiyi@mail.csu.edu.cn [Key Laboratory of Nonferrous Metal Materials Science and Engineering, Ministry of Education, Central South University, Changsha 410083 (China); School of Material Science and Engineering, Central South University, Changsha 410083 (China); Zhou, Xuanwei; Xia, Peng; Liu, Meng [Key Laboratory of Nonferrous Metal Materials Science and Engineering, Ministry of Education, Central South University, Changsha 410083 (China); School of Material Science and Engineering, Central South University, Changsha 410083 (China)

2014-01-01

The thickening of Ω phase in Al–Cu–Mg alloys containing various bulk Ag contents during stress aging at 200 °C with a tensile stress of 240 MPa was investigated by a combination of transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM) and atom probe tomography (APT). TEM characterization confirmed preferred orientation of Ω phase in all stress-aged samples. Corresponding quantitative TEM calculations revealed the thickening kinetics of Ω phase was significantly accelerated during stress aging as compared to that during stress-free aging at 200 °C. HRTEM analysis on the α/Ω interfacial structure confirmed that the applied tensile stress facilitated the rapid nucleation of the growth ledge on the broad face of Ω phase, thereby resulting in the accelerated plate thickening during stress aging at 200 °C. Meanwhile, quantitative TEM analysis highlighted the stress-induced thickening of Ω phase at 200 °C was affected by the bulk Ag content. This was consistent with the HRTEM observation as the ledge nucleation was found to be suppressed with increasing Ag addition. Our APT analysis on different stress-aged samples further suggested the progressive enrichment of Ag atoms in the segregation layer helped to stabilize the interfacial structure and was responsible for the lowest nucleation rate of the ledge in 1.77Ag alloy as compared to that in 0.46Ag alloy.

Stress-induced thickening of Ω phase in Al–Cu–Mg alloys containing various Ag additions

International Nuclear Information System (INIS)

Bai, Song; Liu, Zhiyi; Zhou, Xuanwei; Xia, Peng; Liu, Meng

2014-01-01

The thickening of Ω phase in Al–Cu–Mg alloys containing various bulk Ag contents during stress aging at 200 °C with a tensile stress of 240 MPa was investigated by a combination of transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM) and atom probe tomography (APT). TEM characterization confirmed preferred orientation of Ω phase in all stress-aged samples. Corresponding quantitative TEM calculations revealed the thickening kinetics of Ω phase was significantly accelerated during stress aging as compared to that during stress-free aging at 200 °C. HRTEM analysis on the α/Ω interfacial structure confirmed that the applied tensile stress facilitated the rapid nucleation of the growth ledge on the broad face of Ω phase, thereby resulting in the accelerated plate thickening during stress aging at 200 °C. Meanwhile, quantitative TEM analysis highlighted the stress-induced thickening of Ω phase at 200 °C was affected by the bulk Ag content. This was consistent with the HRTEM observation as the ledge nucleation was found to be suppressed with increasing Ag addition. Our APT analysis on different stress-aged samples further suggested the progressive enrichment of Ag atoms in the segregation layer helped to stabilize the interfacial structure and was responsible for the lowest nucleation rate of the ledge in 1.77Ag alloy as compared to that in 0.46Ag alloy

Heavy metal contamination, microbiological spoilage and biogenic amine content in sushi available on the Polish market.

Science.gov (United States)

Kulawik, Piotr; Dordevic, Dani; Gambuś, Florian; Szczurowska, Katarzyna; Zając, Marzena

2018-05-01

The present study determined the heavy metal contamination (mercury, cadmium, lead, arsenic and nickel) of nori, restaurant-served sushi and ready-to-eat sushi meals available via retail chains. Moreover, both microbiological load and biogenic amine content in ready-to-eat sushi meals were analysed. All of the nori samples contained high levels of Cd (2.122 mg kg -1 ), Ni (0.715 mg kg -1 ), As (34.56 mg kg -1 ) and Pb (0.659 mg kg -1 ). The studied sushi samples contained high levels of Ni and Pb, reaching 0.194 and 0.142 mg kg -1 wet weight, respectively, being potentially hazardous to women during pregnancy and lactation and small children. None of the studied samples contained high levels of Hg. Overall, 37% of ready-to-eat sushi meals exceeded a microbiological load of 10 6  cfu g -1 . However, biogenic amine content in all of the samples was low, with a highest histamine content of 2.05 mg kg -1 . Sushi is not the source of high levels of biogenic amines even with high microbiological loads. Nevertheless, the high microbiological loads at the end of the shelf-life indicate that some processors might have problems with the distribution chain or implement a poor hygienic regime. Moreover as a result of possible risk associated with heavy metal contamination, the present study highlights the need to establish new regulations regarding the contamination of nori and sushi. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Effect of annealing temperature and dopant concentration on the thermoluminescence sensitivity in LiF:Mg,Cu,Ag material.

Science.gov (United States)

Yahyaabadi, Akram; Torkzadeh, Falamarz; Rezaei Ochbelagh, Dariush; Hosseini Pooya, Seyed Mahdi

2018-04-24

LiF:Mg,Cu,Ag is a new dosimetry material that is similar to LiF:Mg,Cu,P in terms of dosimetric properties. The effect of the annealing temperature in the range of 200 to 350°C on the thermoluminescence (TL) sensitivity and the glow curve structure of this material at different concentrations of silver (Ag) was investigated. It has been demonstrated that the optimum values of the annealing temperature and the Ag concentration are 240°C and 0.1 mol% for better sensitivity, respectively. The TL intensity decreases at annealing temperatures lower than 240°C or higher than 240°C, reaching a minimum at 300°C and then again increases for various Ag concentrations. It was observed that the glow curve structure altered and the area under the low temperature peak as well as the area under the main dosimetric peak decreased with increasing annealing temperature. The position of the main dosimetric peak moved in the direction of higher temperatures, but at 320 and 350°C annealing temperatures, it shifted to lower temperatures. It was also observed that the TL sensitivity could partially be recovered by a combined annealing procedure. Copyright © 2018 John Wiley & Sons, Ltd.

Photocatalytic oxidation removal of Hg{sup 0} using ternary Ag/AgI-Ag{sub 2}CO{sub 3} hybrids in wet scrubbing process under fluorescent light

Energy Technology Data Exchange (ETDEWEB)

Zhang, Anchao, E-mail: aczhang@qq.com [School of Mechanical and Power Engineering, Henan Polytechnic University, Jiaozuo, 454000 (China); Zhang, Lixiang; Chen, Xiaozhuan; Zhu, Qifeng; Liu, Zhichao [School of Mechanical and Power Engineering, Henan Polytechnic University, Jiaozuo, 454000 (China); Xiang, Jun, E-mail: xiangjun@mail.hust.edu.cn [State Key Laboratory of Coal Combustion, Huazhong University of Science and Technology, Wuhan, 430074 (China)

2017-01-15

Highlights: • Ag/AgI-Ag{sub 2}CO{sub 3} hybrids were employed for Hg{sup 0} removal under fluorescent light. • Superoxide radical (·O{sub 2}{sup −}) played a key role in Hg{sup 0} removal. • NO exhibited a significant effect on Hg{sup 0} removal in comparison to SO{sub 2}. • The mechanism for enhanced Hg{sup 0} removal over Ag/AgI-Ag{sub 2}CO{sub 3} was proposed. - Abstract: A series of ternary Ag/AgI-Ag{sub 2}CO{sub 3} photocatalysts synthesized using a facile coprecipitation method were employed to investigate their performances of Hg{sup 0} removal in a wet scrubbing reactor. The hybrids were characterized by N{sub 2} adsorption-desorption, XRD, SEM-EDS, HRTEM, XPS, DRS and ESR. The photocatalytic activities of Hg{sup 0} removal were evaluated under fluorescent light. The results showed that AgI content, fluorescent light irradiation, reaction temperature all showed significant influences on Hg{sup 0} removal. NO exhibited significant effect on Hg{sup 0} removal in comparison to SO{sub 2}. Among these ternary Ag/AgI-Ag{sub 2}CO{sub 3} hybrids, Ag/AgI(0.1)-Ag{sub 2}CO{sub 3} showed the highest Hg{sup 0} removal efficiency, which could be ascribed to the effective separation of photogenerated electron-hole pairs between AgI and Ag{sub 2}CO{sub 3} and the surface plasmon resonance (SPR) effect in the visible region by metallic silver nanoparticles (Ag{sup 0} NPs). The trapping studies of reactive radicals showed that the superoxide radicals (·O{sub 2}{sup −}) may play a key role in Hg{sup 0} removal under fluorescent light. According to the experimental and characterization results, a possible photocatalytic oxidation mechanism for enhanced Hg{sup 0} removal over Ag/AgI(0.1)-Ag{sub 2}CO{sub 3} hybrid under fluorescent light was proposed.

Detection of Biogenic Amines in Xuanwei Ham by HPLC%宣威火腿中生物胺的HPLC测定

Institute of Scientific and Technical Information of China (English)

廖国周; 王桂瑛; 曹锦轩; 程志斌

2011-01-01

Biogenic amines content was investigated in Xuanwei ham.Samples were extracted with 0.4 mol/L HClO4,and then derived with dansyl chloride.Separation was achieved using ZORBAX XDB-C18 column and identification,and a quantitative analysis of biogenic amines fraction was carried out using a HPLC system with DAD.Results showed that the linear ranges were 0.5~20 μg/mL,the limit of detection was 0.05~0.1 μg/mL,the recoveries were 81.58%~95.58% and the relative standard deviation were 2.48%~5.85% for eight biogenic amines.Six biogenic amines were detected in Xuanwei ham,the content of β-phenylethylamine,putrescine,cadaverine,tyramine,spermidine and spermine were 0.56 mg/100g,1.45 mg/100g,0.37 mg/100g,3.62 mg/100g,1.26 mg/100g and 4.28 mg/100g,respectively.%以宣威火腿为对象分析其中8种生物胺含量,样品通过0.4 mol/L高氯酸提取后以丹磺酰氯柱前衍生,经ZORBAX XDB-C18柱分离以配备二极管阵列检测器的HPLC对生物胺进行测定。结果表明,该方法中8种生物胺的线性范围为0.5～20μg/mL,检测限为0.05～0.1μg/mL,回收率为81.58%～95.58%,相对标准偏差为2.48%～5.85%,该方法线性范围广,灵敏度和准确度高,可满足定量分析的要求。在宣威火腿中检测出6种生物胺,其中苯乙胺0.56 mg/100g,腐胺1.45 mg/100g,尸胺0.37 mg/100g,酪胺3.62 mg/100g,亚精胺1.26 mg/100g,精胺4.28 mg/100g。

Biogenic robust synthesis of silver nanoparticles using Punica granatum peel and its application as a green catalyst for the reduction of an anthropogenic pollutant 4-nitrophenol

Science.gov (United States)

Edison, T. Jebakumar Immanuel; Sethuraman, M. G.

2013-03-01

A robust synthesis of silver nanoparticles (AgNPs) using the peel extract of Punica granatum is reported in this article. The formation of AgNPs was confirmed by the appearance of brownish yellow color and the Surface Plasmon Resonance (SPR) peak at 432 nm. The biogenic AgNPs were found to have the size approximately 30 nm with distorted spherical shape. The high negative zeta potential values of AgNPs revealed their high stability which could be attributed to the capping of AgNPs by the phytoconstituents of the Punica granatum peel. The biogenic AgNPs were also found to function as an effective green catalyst in the reduction of anthropogenic pollutant viz., 4-nitrophenol (4-NP) by solid sodium borohydride, which was evident from the instantaneous color change of bright yellow (400 nm) to colorless (294 nm) solution, after the addition of AgNPs. The catalytic action of biogenic AgNPs in the reduction of 4-NP could be explained on the basis of Langmuir-Hinshelwood model.

Effects of solution treatment on the microstructure and mechanical properties of Al-Cu-Mg-Ag alloy

International Nuclear Information System (INIS)

Liu, Xiao Yan; Pan, Qing Lin; Lu, Zhi Lun; Cao, Su Fang; He, Yun Bin; Li, Wen Bin

2010-01-01

The effects of solution treatment on the microstructure and mechanical properties of Al-Cu-Mg-Ag alloy were studied by optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), differential scanning calorimeter (DSC), transmission electron microscopy (TEM) and tensile test, respectively. The results show that the mechanical property increases and then decreases with increasing the solution temperature. And the residual phases are dissolved into the matrix gradually, the number fraction of the precipitation and the size of recrystallized grains increase. Compared to the solution temperature, the solution holding time has less effect on the microstructure and the mechanical properties of Al-Cu-Mg-Ag alloy. The overburnt temperature of Al-Cu-Mg-Ag alloy is 525 o C. The yield strength and the elongation get the best when the alloy is solution treated at 515 o C for 1.5 h, is 504 MPa and 12.2% respectively. The fracture mechanism of the samples is ductile fracture.

Theoretical description of metal/oxide interfacial properties: The case of MgO/Ag(001)

Energy Technology Data Exchange (ETDEWEB)

Prada, Stefano [Dipartimento di Scienza dei Materiali, Università di Milano-Bicocca, via R. Cozzi, 53, 20125 Milano (Italy); Giordano, Livia, E-mail: livia.giordano@mater.unimib.it [Dipartimento di Scienza dei Materiali, Università di Milano-Bicocca, via R. Cozzi, 53, 20125 Milano (Italy); Pacchioni, Gianfranco [Dipartimento di Scienza dei Materiali, Università di Milano-Bicocca, via R. Cozzi, 53, 20125 Milano (Italy); Goniakowski, Jacek [CNRS-Sorbonne Universités UPMC Univ. Paris 06, UMR 7588, INSP, F-75005 Paris (France)

2016-12-30

Highlights: • Characteristics of Ag-supported MgO(100) films are studied with different DFT functionals. • All approaches predict a similar nature of supported pristine and oxygen-deficient films. • Interface distances and adhesion are particularly sensitive to the choice of the approximation. • Satisfactory matching with the experiment is obtained with the DFT-optB88 functional. • Charge transfer, work function and vacancy characteristics are little influenced by the method. - Abstract: We compare the performances of different DFT functionals applied to ultra-thin MgO(100) films supported on the Ag(100) surface, a prototypical system of a weakly interacting oxide/metal interface, extensively studied in the past. Beyond semi-local DFT-GGA approximation, we also use the hybrid DFT-HSE approach to improve the description of the oxide electronic structure. Moreover, to better account for the interfacial adhesion, we include the van de Waals interactions by means of either the semi-empirical force fields by Grimme (DFT-D2 and DFT-D2*) or the self-consistent density functional optB88-vdW. We compare and discuss the results on the structural, electronic, and adhesion characteristics of the interface as obtained for pristine and oxygen-deficient Ag-supported MgO films in the 1–4 ML thickness range.

Effects of Cu and Ag additions on age-hardening behavior during multi-step aging in Al--Mg--Si alloys

International Nuclear Information System (INIS)

Kim, JaeHwang; Daniel Marioara, Calin; Holmestad, Randi; Kobayashi, Equo; Sato, Tatsuo

2013-01-01

Low Cu and Ag additions (≤0.10 at%) were found to strongly affect the age-hardening behavior in Al--Mg--Si alloys with Mg+Si>1.5 at%. The hardness increased during aging at 170 °C and the formation of β ″ precipitates was kinetically accelerated. The activation energy of the formation of the β ″ phase was calculated to 127, 105, 108 and 99 KJmol −1 in the base, Cu-added, Ag-added and Cu--Ag-added alloys, respectively using the Kissinger method. The negative effect of two-step aging caused by the formation of Cluster (1) during natural aging was not overcome by the addition of microalloying elements. However, it was suppressed by the formation of Cluster (2) through a pre-aging at 100 °C. Quantitative analysis of the precipitate microstructure was performed using a transmission electron microscope equipped with a parallel electron energy loss spectrometer for the determination of specimen thickness. The formation of Cluster (2) was found to increase the number density of β ″ precipitates, whereas the formation of Cluster (1) decreased the number density and increased the needle length. The effects of low Cu and Ag additions in combination with multi-step aging are discussed based on microstructure observations and hardness and resistivity measurements.

Decay kinetics study of Ag0 in silver doped barium aluminoborate glasses

International Nuclear Information System (INIS)

Pontuschka, W.M.; Santos, J.T. dos; Isotani, S.; Rabbani, S.R.

1989-12-01

EPR measurements of 30BaO.50B 2 O 3 .20Al 2 O 3 at. % glasses containing different amounts of silver impurity, X-and γ-irradiated at room temperature, showed the presence of Ag 0 and Ag ++ centers. Decay kinetics of Ag 0 was determined for different temperatures in glass containing 0.1% of silver. We show that our model of stabilization energy of H 0 in B-O rings through van der Waals forces is not applicable to Ag 0 . Thus, we propose the model of reduction of Ag 0 to Ag + as the mechanism of the Ag 0 decay kinetics. (author) [pt

(0 0 1) textured CoPt-Ag nanocomposite films for high-density perpendicular magnetic recording

International Nuclear Information System (INIS)

Xue, S.X.; Wang, H.; Wang, H.B.; Yang, F.J.; Wang, J.A.; Cao, X.; Gao, Y.; Huang, Z.B.; Li, Z.Y.; Li, Q.; Wong, S.P.

2006-01-01

CoPt/Ag nanocomposite films were prepared by magnetron sputtering. The dependence of texture and magnetic properties on film thickness, Ag atomic fraction and annealing conditions is investigated. Films with a thickness about 20 nm are easy to form with (0 0 1) orientation. The existence of the Ag in the film plays a dominant role in inducing the (0 0 1) texture of the film and suppressing the growth of the CoPt grains during annealing. The Co 35 Pt 38 Ag 27 film after annealing at 600 deg. C exhibits a large perpendicular coercivity of 5.6 kOe and a squareness of 0.90 with a small average grains size of 12.5 nm

Reducing strength prevailing at root surface of plants promotes reduction of Ag+ and generation of Ag(0/Ag2O nanoparticles exogenously in aqueous phase.

Directory of Open Access Journals (Sweden)

Peddisetty Pardha-Saradhi

Full Text Available Potential of root system of plants from wide range of families to effectively reduce membrane impermeable ferricyanide to ferrocyanide and blue coloured 2,6-dichlorophenol indophenol (DCPIP to colourless DCPIPH2 both under non-sterile and sterile conditions, revealed prevalence of immense reducing strength at root surface. As generation of silver nanoparticles (NPs from Ag+ involves reduction, present investigations were carried to evaluate if reducing strength prevailing at surface of root system can be exploited for reduction of Ag+ and exogenous generation of silver-NPs. Root system of intact plants of 16 species from 11 diverse families of angiosperms turned clear colorless AgNO3 solutions, turbid brown. Absorption spectra of these turbid brown solutions showed silver-NPs specific surface plasmon resonance peak. Transmission electron microscope coupled with energy dispersive X-ray confirmed the presence of distinct NPs in the range of 5-50 nm containing Ag. Selected area electron diffraction and powder X-ray diffraction patterns of the silver NPs showed Bragg reflections, characteristic of crystalline face-centered cubic structure of Ag(0 and cubic structure of Ag2O. Root system of intact plants raised under sterile conditions also generated Ag(0/Ag2O-NPs under strict sterile conditions in a manner similar to that recorded under non-sterile conditions. This revealed the inbuilt potential of root system to generate Ag(0/Ag2O-NPs independent of any microorganism. Roots of intact plants reduced triphenyltetrazolium to triphenylformazon and impermeable ferricyanide to ferrocyanide, suggesting involvement of plasma membrane bound dehydrogenases in reduction of Ag+ and formation of Ag(0/Ag2O-NPs. Root enzyme extract reduced triphenyltetrazolium to triphenylformazon and Ag+ to Ag(0 in presence of NADH, clearly establishing potential of dehydrogenases to reduce Ag+ to Ag(0, which generate Ag(0/Ag2O-NPs. Findings presented in this manuscript put

Arsenic removal from acidic solutions with biogenic ferric precipitates

Energy Technology Data Exchange (ETDEWEB)

Ahoranta, Sarita H., E-mail: sarita.ahoranta@tut.fi [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Kokko, Marika E., E-mail: marika.kokko@tut.fi [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Papirio, Stefano, E-mail: stefano.papirio@unicas.it [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Özkaya, Bestamin, E-mail: bozkaya@yildiz.edu.tr [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Department of Environmental Engineering, Yildiz Technical University, Davutpasa Campus 34220, Esenler, Istanbul (Turkey); Puhakka, Jaakko A., E-mail: jaakko.puhakka@tut.fi [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland)

2016-04-05

Highlights: • Continuous and rapid arsenic removal with biogenic jarosite was achieved at pH 3.0. • Arsenic removal was inefficient below pH 2.4 due to reduced Fe–As co-precipitation. • As(V) had better sorption characteristics than As(III). • Biogenic jarosite adsorbed arsenic more effectively than synthetic jarosite. - Abstract: Treatment of acidic solution containing 5 g/L of Fe(II) and 10 mg/L of As(III) was studied in a system consisting of a biological fluidized-bed reactor (FBR) for iron oxidation, and a gravity settler for iron precipitation and separation of the ferric precipitates. At pH 3.0 and FBR retention time of 5.7 h, 96–98% of the added Fe(II) precipitated (99.1% of which was jarosite). The highest iron oxidation and precipitation rates were 1070 and 28 mg/L/h, respectively, and were achieved at pH 3.0. Subsequently, the effect of pH on arsenic removal through sorption and/or co-precipitation was examined by gradually decreasing solution pH from 3.0 to 1.6 (feed pH). At pH 3.0, 2.4 and 1.6, the highest arsenic removal efficiencies obtained were 99.5%, 80.1% and 7.1%, respectively. As the system had ferric precipitates in excess, decreased arsenic removal was likely due to reduced co-precipitation at pH < 2.4. As(III) was partially oxidized to As(V) in the system. In shake flask experiments, As(V) sorbed onto jarosite better than As(III). Moreover, the sorption capacity of biogenic jarosite was significantly higher than that of synthetic jarosite. The developed bioprocess simultaneously and efficiently removes iron and arsenic from acidic solutions, indicating potential for mining wastewater treatment.

Effect of Mixed Glass Former on Ionic Conductivity of Silver Boron Tungstate glass system x[0.75AgI:0.25AgCl]: (1-x) [Ag2O-(B2O3:WO3)

International Nuclear Information System (INIS)

Dehariya, Harsha; Kumar, R; Polu, A R

2012-01-01

The idea to explore new 'Superionic Electrolytes', 'Fast ionic conductors' is due to their tremendous potential applications in solid state electrochemical devices viz. solid state batteries, fuel cells, sensors, super capacitors. Superionic glasses have attracted great deal of attention due to their several advantageous over their crystalline counterparts such as high ionic conductivity, easy preparation, wide selection of compositions, isotropic properties and high stability etc [4-7]. Large numbers of silver ion based glasses have been reported in the literature for the glassy system of AgI:Ag2O: MxOy (MxOy = B2O3, SiO2, P2O5, GeO2, V2O5, As2O5, CrO3, SeO2, MoO3 and TeO3 etc many of them shows high silver ion conductivity [8]. Ion transport behavior of Silver Boro Tungstate glass system x[0.75AgI:0.25AgCl]: (1-x) [Ag2O(B2O3:WO3)], where 0 ≤ x ≤ 1 in molar wt% prepared by melt quench technique were reported. The new host [0.75AgI:0.25AgCl] was used as a better alternate in place of conventional host salt AgI. Conductivity measurement were carried out on this glass system as a function of frequency from 50 Hz to 5 MHz, over a temperature range of 27 C to 200 C, for different compositions by Impedance spectroscopy. The composition 0.7[0.75AgI:0.25AgCl]: 0.3[Ag2O(B2O3:WO3)] shows the highest conductivity of the order of σrt ∼ 2.76x10-2 S/cm, referred to as the Optimum Conducting Composition (OCC). The enhancement in the conductivity has been obtained by mixed former effect. XRD result shows that the system is completely amorphous. Temperature dependence of conductivity of all compositions were studied and reported. Activation energies (Ea) were also evaluated from the slope of .Log(σ) vs 1000/T, Arrhenius plots.

Effect of Mixed Glass Former on Ionic Conductivity of Silver Boro Tungstate glass system x[0.75AgI:0.25AgCl]: (1-x) [Ag2O-{B2O3:WO3}

Science.gov (United States)

Dehariya, Harsha; Kumar, R.; Polu, A. R.

2012-05-01

The idea to explore new 'Superionic Electrolytes', "Fast ionic conductors" is due to their tremendous potential applications in solid state electrochemical devices viz. solid state batteries, fuel cells, sensors, super capacitors. Superionic glasses have attracted great deal of attention due to their several advantageous over their crystalline counterparts such as high ionic conductivity, easy preparation, wide selection of compositions, isotropic properties and high stability etc [4-7]. Large numbers of silver ion based glasses have been reported in the literature for the glassy system of AgI:Ag2O: MxOy (MxOy = B2O3, SiO2, P2O5, GeO2, V2O5, As2O5, CrO3, SeO2, MoO3 & TeO3 etc many of them shows high silver ion conductivity [8]. Ion transport behavior of Silver Boro Tungstate glass system x[0.75AgI:0.25AgCl]: (1-x) [Ag2O{B2O3:WO3}], where 0 <= x <= 1 in molar wt% prepared by melt quench technique were reported. The new host [0.75AgI:0.25AgCl] was used as a better alternate in place of conventional host salt AgI. Conductivity measurement were carried out on this glass system as a function of frequency from 50 Hz to 5 MHz, over a temperature range of 27°C to 200°C, for different compositions by Impedance spectroscopy. The composition 0.7[0.75AgI:0.25AgCl]: 0.3[Ag2O{B2O3:WO3}] shows the highest conductivity of the order of σrt ~ 2.76 × 10-2 S/cm, referred to as the Optimum Conducting Composition (OCC). The enhancement in the conductivity has been obtained by mixed former effect. XRD result shows that the system is completely amorphous. Temperature dependence of conductivity of all compositions were studied & reported. Activation energies (Ea) were also evaluated from the slope of .Log(σ) vs 1000/T, Arrhenius plots.

A perfect wetting of Mg monolayer on Ag(111) under atomic scale investigation: First principles calculations, scanning tunneling microscopy, and Auger spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Migaou, Amani; Guiltat, Mathilde; Payen, Kevin; Landa, Georges; Hémeryck, Anne, E-mail: anne.hemeryck@laas.fr [LAAS-CNRS, Université de Toulouse, CNRS, UPS, Toulouse (France); Sarpi, Brice; Daineche, Rachid; Vizzini, Sébastien [Aix Marseille University, IM2NP, Fac Sci St. Jérôme, F-13397 Marseille (France)

2016-05-21

First principles calculations, scanning tunneling microscopy, and Auger spectroscopy experiments of the adsorption of Mg on Ag(111) substrate are conducted. This detailed study reveals that an atomic scale controlled deposition of a metallic Mg monolayer perfectly wets the silver substrate without any alloy formation at the interface at room temperature. A liquid-like behavior of the Mg species on the Ag substrate is highlighted as no dot formation is observed when coverage increases. Finally a layer-by-layer growth mode of Mg on Ag(111) can be predicted, thanks to density functional theory calculations as observed experimentally.

Thermodynamic investigation of the ternary mixed aqueous electrolyte (MgCl{sub 2} + MgSO{sub 4}) system by potentiometric method at T = 298.15 K

Energy Technology Data Exchange (ETDEWEB)

Bagherinia, Mohammad A., E-mail: mabagherinia@yahoo.com [Department of Chemistry, Faculty of Science, Lahijan Branch, Islamic Azad University, Lahijan (Iran, Islamic Republic of); Giahi, Masoud; Pournaghdy, Mohammad; Vaghar, Gholam R. [Department of Chemistry, Faculty of Science, Lahijan Branch, Islamic Azad University, Lahijan (Iran, Islamic Republic of)

2012-01-15

Highlights: > In this study we investigated the thermodynamic properties of MgCl{sub 2} + MgSO{sub 4} + H{sub 2}O. > The method used in this work was potentiometric method. > Mg-ISE and the Ag/AgCl electrodes used in this work had a good Nernst response. > The experimental results obeyed the Harned rule. > The Pitzer model could be used to describe this ternary system satisfactorily. - Abstract: This work reports the results of thermodynamic investigation of the ternary mixed-electrolyte system (MgCl{sub 2} + MgSO{sub 4} + H{sub 2}O). The investigation was performed based on Pitzer ion interaction model by using the potentiometric technique at T = 298.15 K. The mean activity coefficients of MgCl{sub 2} in the mixed aqueous electrolyte system were determined on the galvanic cell without liquid junction of the type: Mg-ISE|MgCl{sub 2} (m{sub A}), MgSO{sub 4} (m{sub B}), H{sub 2}O|Ag/AgCl over total ionic strengths from (0.001 to 8.000) mol . kg{sup -1} for different series of salt ratio r (r=m{sub MgCl{sub 2}}/m{sub MgSO{sub 4}}=2.5,5.0,7.5,10.0,15.0 and pure MgCl{sub 2}). The PVC based magnesium ion-selective electrode (Mg-ISE) and the Ag/AgCl electrode used in this work were made in our laboratory and had a reasonably good Nernst response. The experimental results obeyed the Harned rule, and the Pitzer model could be used to describe this ternary system satisfactorily. Pitzer ion-interaction parameters for mixed salts were determined for this system. Then, these parameters ({theta}{sub ClSO{sub 4}}=0.0252{+-}0.0042, {psi}{sub MgClSO{sub 4}}=-0.0049{+-}0.0003) were used to calculate the values of the mean activity coefficients of MgSO{sub 4}, the osmotic coefficients of water ({phi}) and the excess Gibbs free energies of solution (G{sup E}) for the whole series of the studied electrolyte systems.

Fatigue and creep deformed microstructures of aged alloys based on Al-4% Cu-0.3% Mg

International Nuclear Information System (INIS)

Reddy, A. Somi

2008-01-01

The addition of 0.4 wt.% of silver or cadmium to the alloy Al-4% Cu-0.3% Mg which has a high Cu:Mg ratio, changes the nature, morphology and dispersion of the precipitates that forms on age hardening at medium temperatures such as 150-200 o C. Fatigue and creep tests were carried out on alloys aged to peak strength at 170 o C. The tensile properties of the alloys aged at 170 o C increased in the order Al-4% Cu, Al-4% Cu-0.3% Mg, Al-4% Cu-0.3% Mg-0.4% Cd, and Al-4% Cu-0.3% Mg-0.4% Ag. Despite differences in their microstructures and tensile properties, the fatigue performance of the alloys was relatively unaffected. Fatigue behaviour was similar in each case and the alloys showed identical fatigue limits. Major differences were observed in the creep performance of the alloys creep tested at 150 o C in the peak strength condition age hardened at 170 o C. Creep performance of the alloys increased in the order of their tensile properties. The purpose of the present work was to discuss the fatigue and creep deformed microstructure of these alloys

Alloy development for the enhanced stability of Ω precipitates in Al-Cu-Mg-Ag alloys

Science.gov (United States)

Gable, B. M.; Shiflet, G. J.; Starke, E. A.

2006-04-01

The coarsening resistance and thermal stability of several Ω plate-dominated microstructures were controlled through altering the chemistry and thermomechanical processing of various Al-Cu-Mg-Ag alloys. Quantitative comparisons of Ω nucleation density, particle size, and thermal stability were used to illustrate the effects of alloy composition and processing conditions. The long-term stability of Ω plates was found to coincide with relatively high levels of silver and moderate magnesium additions, with the latter limiting the competition for solute with S-phase precipitation. This analysis revealed that certain microstructures initially dominated by Ω precipitation were found to remain stable through long-term isothermal and double-aging heat treatments, which represents significant improvement over the previous generation of Al-Cu-Mg-Ag alloys, in which Ω plates dissolved sacrificially after long aging times. The quantitative precipitate data, in conjunction with a thermodynamic database for the aluminum-rich corner of the Al-Cu-Mg-Ag quaternary system, were used to estimate the chemistry of the α/Ω-interphase boundary. These calculations suggest that silver is the limiting species at the α/Ω interfacial layer and that Ω plates form with varying interfacial chemistries during the early stages of artificial aging, which is directly related to the overall stability of certain plates.

Clinical value of single or combined IRMA of CEA, CA19-9, CA72-4 and MG-Ag in diagnosis of gastric cancer

International Nuclear Information System (INIS)

Li Jiangang; Chen Zhong; Liu Yun; Zhang Jun

2002-01-01

Four tumor markers CEA, CA19-9, CA72-4 and MG-Ag are chosen in diagnosis of gastric cancer and 228 cases are detected with single or combined methods in all. The results indicate that the positive rates of single detection are all above 70% and that of MG-Ag is the highest (90.4%). Combined detections of two tumor markers, as judged by double positivity, the positive rate of MG + CA72-4 is the highest (70.6%), next is MG + CA19-9 (64.6%). It is suggested that MG-Ag is the first choice in single detection, MG + CA72-4 group is the first choice in double combined detections and different tumor markers could be chosen according to historic type in follow-up patients

Homogeneous-inhomogeneous models of Ag x (Ge0.25Se0.75)100-x bulk glasses

International Nuclear Information System (INIS)

Arcondo, B.; Urena, M.A.; Piarristeguy, A.; Pradel, A.; Fontana, M.

2007-01-01

Ge-Se system presents an extensive glass forming composition range even when different metals (Ag, Sb, Bi) are added. In spite that the addition of Ag (up to 30 at%) to Ge-Se does not affect substantially the glass forming tendency, it impacts significantly on the transport properties. (Ge 0.25 Se 0.75 ) 100- x Ag x is a fast ionic conductor with x≥8 at% whereas it is a semiconductor for x 0.25 Se 0.75 ) 100- x Ag x bulk samples. These results appear to sustain this model. However previous structural and thermal studies oppose it. Moessbauer spectrometry on samples (0≤x≤25) containing 0.5 at% of 57 Fe is performed at T≤300 K. The main contribution to the glasses spectra correspond to low spin Fe 2+ in octahedral coordination and high spin Fe 2+ in distorted octahedral environments. The relative population of both sites changes continuously as Ag concentration varies denoting that the change in the transport behavior obeys to a percolation phenomenon. The low temperature results are discussed with the aim to throw light on the controversy about the homogeneity-inhomogeneity of the studied bulk glasses

Biogenic amines in the meat of hunted pheasant and hare during the course of storage

Directory of Open Access Journals (Sweden)

Zdeňka Hutařová

2014-01-01

Full Text Available Venison is becoming more and more interesting for consumers. Although treatment procedures of hunted game differ from slaughtered livestock, the hygienic quality of game meat must still be ensured. Potential indicators of meat hygienic quality include the content of biogenic amines. The aim of the present study was to assess the content and changes of biogenic amines in the muscles of selected kinds of small game (common pheasant and brown hare during storage, and based on the obtained results, to assess the hygienic quality of the meat. Biogenic amines (putrescine, cadaverine, histamine, tyramine, phenylethylamine, and tryptamine in the breast and thigh muscles separated by reverse phase liquid chromatography and consequently were detected using tandem mass spectrometry. Based on the determined content of biogenic amines, both pheasant and hare meats complied with values of high quality meat. The sum of biogenic amines did not exceed the value of 5 mg/kg after 7 days at 0 °C or 7 °C in pheasant meat, and after 21 days at 0 °C or after 14 days at 7 °C in brown hare meat. The biogenic amine content and the speed of their formation in venison can be very helpful for the evaluation of both meat hygienic quality and safety of these foods during storage.

First principles study of the Ag nanoclusters adsorption effect on the photocatalytic properties of AgBr(1 1 0) surface

Science.gov (United States)

Chi, Yuhua; Zhao, Lianming; Li, Xue; Zhu, Houyu; Guo, Wenyue

2018-05-01

The electronic structures and photocatalytic performance of Agn/AgBr(1 1 0)(n = 7-13) are studied using density functional theory (DFT). The adsorption of Agn (n = 7-13) nanoclusters on AgBr(1 1 0) surface induces a new metal-induced gap band (MIGB) located between the valence band (VB) and the conduction band (CB), the variety of the electronic characters of AgBr(1 1 0) favor the visible and infrared light absorption, which improves the sunlight utilization. The dominant localization of the photo-excited electrons on the Agn clusters of Agn/AgBr(1 1 0)(n = 7-13) facilitates the oxidation-reduction reactions occurring on the surface and also effectively reduces the photolysis of AgBr under the sunlight irradiation. The overpotentials of the CB and VB edges indicate that photocatalytic conversion of CO2 with H2O to methanol is possible on AgBr(1 1 0) deposited with the Agn nanoclusters, which has been realized experimentally (An et al., 2012). The substantial strengthening of visible and infrared light absorption and the free energy profiles for the conversion of CO2 with H2O to methanol indicate that Ag13/AgBr(1 1 0) surface can be expected to be the excellent photocatalysts.

Calcite growth-rate inhibition by fulvic acid and magnesium ion—Possible influence on biogenic calcite formation

Science.gov (United States)

Reddy, Michael M.

2012-01-01

Increases in ocean surface water dissolved carbon dioxide (CO2) concentrations retard biocalcification by reducing calcite supersaturation (Ωc). Reduced calcification rates may influence growth-rate dependent magnesium ion (Mg) incorporation into biogenic calcite modifying the use of calcifying organisms as paleoclimate proxies. Fulvic acid (FA) at biocalcification sites may further reduce calcification rates. Calcite growth-rate inhibition by FA and Mg, two common constituents of seawater and soil water involved in the formation of biogenic calcite, was measured separately and in combination under identical, highly reproducible experimental conditions. Calcite growth rates (pH=8.5 and Ωc=4.5) are reduced by FA (0.5 mg/L) to 47% and by Mg (10−4 M) to 38%, compared to control experiments containing no added growth-rate inhibitor. Humic acid (HA) is twice as effective a calcite growth-rate inhibitor as FA. Calcite growth rate in the presence of both FA (0.5 mg/L) and Mg (10−4 M) is reduced to 5% of the control rate. Mg inhibits calcite growth rates by substitution for calcium ion at the growth site. In contrast, FA inhibits calcite growth rates by binding multiple carboxylate groups on the calcite surface. FA and Mg together have an increased affinity for the calcite growth sites reducing calcite growth rates.

Magnetic and transport properties of Cu1.05Cr0.89 Mg0.05O2 and Cu0.96Cr0.95 Mg0.05Mn0.04O2 films

International Nuclear Information System (INIS)

Xu Qingyu; Schmidt, Heidemarie; Zhou Shengqiang; Potzger, Kay; Helm, Manfred; Hochmuth, Holger; Lorenz, Michael; Meinecke, Christoph; Grundmann, Marius

2008-01-01

We prepared conductive, polycrystalline or amorphous Cu 1.05 Cr 0.89 Mg 0.05 O 2 films on a-plane sapphire substrates by pulsed laser deposition under different O 2 partial pressure and substrate temperature. Hall measurements were performed to study the majority carrier type in these films. Polycrystalline Cu 1.05 Cr 0.89 Mg 0.05 O 2 is n-type conducting at 290 K, while in amorphous Cu 1.05 Cr 0.89 Mg 0.05 O 2 the type of majority charge carriers changes from electrons to holes at around 270 K. Interestingly, the structure has little influence on the magnetic properties of the films. A clear antiferromagnetic to paramagnetic transition was observed in both polycrystalline and amorphous Cu 1.05 Cr 0.89 Mg 0.05 O 2 films at 25 K. Similar electrical properties to Cu 1.05 Cr 0.89 Mg 0.05 O 2 film were observed for Cu 0.96 Cr 0.95 Mg 0.05 Mn 0.04 O 2 in dependence on the structure, while only paramagnetic without antiferromagnetic ordering was observed down to 5 K. Large negative magnetoresistance of 27% at 20 K was observed at 6 T in amorphous Cu 1.05 Cr 0.89 Mg 0.05 O 2 film

Influence of 45S5 Bioglass addition on microstructure and properties of ultrafine grained (Mg-4Y-5.5Dy-0.5Zr) alloy

Energy Technology Data Exchange (ETDEWEB)

Kowalski, K., E-mail: kamil.kowalski@put.poznan.pl [Institute of Materials Science and Engineering, Poznan University of Technology, Jana Pawla II 24, 61-138 Poznan (Poland); Jurczyk, M.U. [Division of Mother’s and Child’s Health, Poznan University of Medical Sciences, Polna 33, 60-535 Poznan (Poland); Wirstlein, P.K. [Department of Gynecology and Obstetrics, Division of Reproduction, Poznan University of Medical Sciences, Polna 33, 60-535 Poznan (Poland); Jakubowicz, J.; Jurczyk, M. [Institute of Materials Science and Engineering, Poznan University of Technology, Jana Pawla II 24, 61-138 Poznan (Poland)

2017-05-15

Highlights: • Ultrafine grained composites were formed by consolidating mechanically alloyed powders. • Mechanical properties were sensitive to the content of 45S5 Bioglass in Mg-4Y-5.5Dy-0.5Zr alloy. • Fluoride treated composites displayed superior corrosion resistance in Ringer solution. • Composites modified with MgF{sub 2} have a higher degree of biocompatibility in comparison with the unmodified reference material. - Abstract: Bulk samples of an ultrafine grained (Mg-4Y-5.5Dy-0.5Zr)-x wt% 45S5 Bioglass (x = 0, 5) and (Mg-4Y-5.5Dy-0.5Zr)-5 wt% 45S5 Bioglass-1 wt% Ag composites have been synthesized by consolidating mechanically alloyed powders. The influence of the chemical composition on the microstructure, mechanical properties and corrosion behavior of bulk composites were studied. The sintering of (Mg-4Y-5.5Dy-0.5Zr)-5 wt% 45S5 Bioglass powders led to the formation of a bulk composite with grain size of approx. 95 nm. The corrosion behavior of Mg-based composites before and after hydrofluoric acid treatment was also investigated. The ultrafine grained (Mg-4Y-5.5Dy-0.5Zr)-5 wt% 45S5 Bioglass composite was more corrosion resistant than the bulk Mg-4Y-5.5Dy-0.5Zr alloy after HF treatment. The in vitro biocompatibility of synthesized composites was evaluated and compared with microcrystalline magnesium. Magnesium, (Mg-4Y-5.5Dy-0.5Zr)-5 wt% 45S5 Bioglass and (Mg-4Y-5.5Dy-0.5Zr)-5 wt% 45S5 Bioglass-1 wt% Ag composites modified with MgF{sub 2} have a higher degree of biocompatibility in comparison with the unmodified reference material.

Formation of Biogenic Amines in Chicken Meat Stored under Modified Atmosphere

Directory of Open Access Journals (Sweden)

Leo Gallas

2010-01-01

Full Text Available The aim of the study was to investigate the effects of two modified atmospheres with a different combination of gases on selected groups of microorganisms and on concentrations of biogenic amines (BAs in samples of poultry breast muscle. The samples were packaged under modified atmosphere A (75% O2 a 25% CO2 or B (75% N2 and 25% CO2 and stored at temperatures from +2 to +4 °C for 14 days. During the storage period, O2 concentrations in modified atmosphere A (MA A decreased from the initial 74.8 ± 0.3% to 55.9 ± 6.6% at the end of the storage period. In all samples, counts of psychrotrophic bacteria counts, Brochothrix thermosphacta, lactic acid bacteria and coliform microorganism were determined. The tests were made on the packaging day, and then after three, nine and fourteen days of storage. At the end of the storage period, higher numbers of psychrotrophic bacteria (6.5 ± 0.7 log10 cfu g-1, Brochothrix thermosphacta (4.8 ± 0.3 log10 cfu g-1 and lactic acid bacteria (1.7 ± 0.4 log10 cfu g-1 were found on samples packaged under MA A. Samples packaged under modified atmosphere B on the other hand contained higher numbers of coliform bacteria (4.1 ± 0.6 log10 cfu g-1 at the end of the storage period. In addition to microbiological indicators, concentrations of biogenic amines (putrescine, cadaverine, histamine, tyramine, spermine, spermidine and β-phenylethylamine were also determined. In fresh samples and after three days of storage, only spermine and spermidine were found. After 9 and 14 days, also other BAs were detected. The biogenic amine totals at the end of the storage period was 60.0 ± 13.2 mg kg-1 in samples packaged under MA A and 129.0 ± 41.3 mg kg-1 in samples packaged under MA B. The most abundantly represented biogenic amines in samples packaged under MA A were putrescine and spermine (49.7 and 24.8%, respectively, at the end of the storage period, and putrescine and cadaverine in samples packaged under MA B (47.0 and 32

Half-lives of isomeric levels of sup 1 sup 0 sup 7 sup m Ag, sup 1 sup 0 sup 9 sup m Ag and sup 1 sup 0 sup 3 sup m Rh photoactivated by sup 6 sup 0 Co gamma-ray irradiation

CERN Document Server

Yoshida, E; Kojima, Y; Shizuma, K

2000-01-01

Photoactivation by gamma-rays from sup 6 sup 0 Co of 10 kCi has been performed for isomers of sup 1 sup 0 sup 7 sup m Ag, sup 1 sup 0 sup 9 sup m Ag and sup 1 sup 0 sup 3 sup m Rh and half-lives of these isomers were determined. Gamma-rays emitted from sup 1 sup 0 sup 7 sup m Ag and sup 1 sup 0 sup 9 sup m Ag were measured with a low-background Ge detector and internal conversion electrons from sup 1 sup 0 sup 3 sup m Rh were measured with a 2 pi gas flow counter. The half-lives obtained are: sup 1 sup 0 sup 7 sup m Ag: 44.5+-0.8 s, sup 1 sup 0 sup 9 sup m Ag: 38.0+-1.2 s and sup 1 sup 0 sup 3 sup m Rh: 54.8+-3.8 min. The results are in agreement with previous values obtained by different excitation methods.

Effect of Ag additions on the lengthening rate of Ω plates and formation of σ phase in Al-Cu-Mg alloys during thermal exposure

Energy Technology Data Exchange (ETDEWEB)

Zhou, Yaru; Liu, Zhiyi, E-mail: liuzhiyi@csu.edu.cn; Bai, Song; Ying, Puyou; Lin, Lianghua

2017-01-15

Effect of Ag additions on the mechanical properties and microstructures of the peak-aged Al-Cu-Mg alloys during prolonged thermal exposure at 150 °C, was investigated by tensile testing, conventional transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM). The results showed that after exposure for 500 h, > 85% of the peak strength remained. Microstructure observations indicated that increasing the Ag content from 0.14 to 0.57% promoted the precipitation of a fine and uniform Ω phase and suppressed the formation of the θ′ phase, leading to a notable improvement of the strength properties and thermal stability of the studied alloys. Quantitative TEM analysis showed that the coarsening of Ω phase was predominated by plate lengthening rather than thickening, while its lengthening rate was independent of various Ag additions during exposure at 150 °C. In addition, an increase of Ag also facilitated the formation of a cubic σ phase, which was further supported by STEM results. - Highlights: •Increasing Ag improved strength properties and thermal stability of the alloys. •After exposure for 500 h, > 85% of the peak strength remained. •The lengthening rate of Ω plates remained constant as Ag increased at 150 °C. •Increasing Ag content facilitated the formation of σ phase.

Mechanism of phase transformations in Mg-based alloys subjected to plasma immersion ion implantation of Ag

International Nuclear Information System (INIS)

Kutsenko, Larisa; Fuks, David; Kiv, Arnold; Talianker, Michael; Burlaka, Ljubov; Monteiro, Othon; Brown, Ian

2006-01-01

The formation of a new phase of composition Mg 54 Al 28 Ag 18 was observed as a result of plasma immersion ion implantation of Ag into the compound Mg 17 Al 12 . The new structure was characterized using a micro-beam diffraction technique. It was found that the implantation-induced phase transition occurs when the retained dose of the implanted ions is within the range of about 10 15 -10 16 ions/cm 2 . The implanted system has been studied theoretically by means of density-functional electronic structure calculations and a new ab initio approach has been developed to evaluate the specific concentrations of the implanted ions that might cause the phase transition effect in the implanted matrix. The theoretically estimated values of concentrations are in good agreement with experimental observations

Enzyme sensor array for the determination of biogenic amines in food samples

Energy Technology Data Exchange (ETDEWEB)

Lange, Jana [University of Greifswald, Institute for Chemistry and Biochemistry (Germany); Wittmann, Christine [Fachhochschule Neubrandenburg, Department of Technology (Germany)

2002-01-01

An enzyme sensor array for the simultaneous determination of the three biogenic amines (histamine, tyramine and putrescine) by pattern recognition using an artificial neural network and its application to different food samples is described. A combination of a monoamine oxidase, a tyramine oxidase and a diamine oxidase (with specific activities sufficient for rapid detection) are immobilised each on a separate screen-printed thick-film electrode via transglutaminase and glutaraldehyde to compare these cross-linking reagents with regard to their suitability. To calculate the amount of a specific biogenic amine, the raw data from multichannel software were transferred to a neural network. The sensor array takes 20 min to complete (excluding statistical data analysis) with only one extraction and subsequent neutralisation step required prior to sensor measurement. The lower detection limits with the enzyme sensor were 10 mg/kg for histamine and tyramine, and 5 mg/kg for putrescine with a linear range up to 200 mg/kg for histamine and tyramine and 100 mg/kg for putrescine. The application area of the enzyme sensor array was tested from fish to meat products, sauerkraut, beer, dairy products, wine and further fermented foods and compared with the data of conventional LC analyses (mean correlation coefficient: 0.854). (orig.)

Production of BiPbSrCaCuO thin films on MgO and Ag/MgO substrates by electron beam deposition techniques

CERN Document Server

Varilci, A; Gorur, O; Celebi, S; Karaca, I

2002-01-01

Superconducting BiPbSrCaCuO thin films were prepared on MgO(001) and Ag/MgO substrates using an electron beam (e-beam) evaporation technique. The effects of annealing temperature and Ag diffusion on the crystalline structure and some superconducting properties, respectively, were investigated by X-ray diffraction, atomic force microscopy, and by measurements of the critical temperature and the critical current density. It was shown that an annealing of both types of films at 845 or 860 C resulted in the formation of mixed Bi-2223 and Bi-2212 phases with a high degree of preferential orientation with the c-axis perpendicular to the substrates. The slight increase of the critical temperature from 103 K to 105 K, the enhancement of the critical current density from 2 x 10 sup 3 to 6 x 10 sup 4 A/cm sup 2 , and the improved surface smoothness are due to a possible silver doping from the substrate. (Abstract Copyright [2002], Wiley Periodicals, Inc.)

Low-Temperature Sintering Li3Mg1.8Ca0.2NbO6 Microwave Dielectric Ceramics with LMZBS Glass

Science.gov (United States)

Wang, Gang; Zhang, Huaiwu; Liu, Cheng; Su, Hua; Jia, Lijun; Li, Jie; Huang, Xin; Gan, Gongwen

2018-05-01

Li3Mg1.8Ca0.2NbO6 ceramics doped with Li2O-MgO-ZnO-B2O3-SiO2 glass (LMZBS) were prepared via a solid-state route. The LMZBS glass effectively reduced the sintering temperature of Li3Mg1.8Ca0.2NbO6 ceramics to 950°C. The effects of the LMZBS glass on the sintering behavior, microstructures and microwave dielectric properties of Li3Mg1.8Ca0.2NbO6 ceramics are discussed in detail. Among all the LMZBS doped Li3Mg1.8Ca0.2NbO6 ceramics, the sample with 1 wt.% of LMZBS glass sintered at 950°C for 4 h exhibited good dielectric properties: ɛ r = 16.7, Q × f = 31,000 GHz (9.92 GHz), τ f = - 1.3 ppm/°C. The Li3Mg1.8Ca0.2NbO6 ceramics possessed excellent chemical compatibility with Ag electrodes, and could be applied in low temperature co-fired ceramics (LTCC) applications.

Alkali ion scattering from Ag(0 0 1) and Ag thin films at low and hyperthermal energies

Energy Technology Data Exchange (ETDEWEB)

Ray, M.P.; Lake, R.E. [Department of Physics and Astronomy, Clemson University, 118 Kinard Laboratory, Clemson, South Carolina 29634 (United States); Sosolik, C.E. [Department of Physics and Astronomy, Clemson University, 118 Kinard Laboratory, Clemson, South Carolina 29634 (United States)], E-mail: sosolik@clemson.edu

2009-02-15

We have investigated the scattering of K{sup +} and Cs{sup +} ions from a single crystal Ag(0 0 1) surface and from a Ag-Si(1 0 0) Schottky diode structure. For the K{sup +} ions, incident energies of 25 eV to 1 keV were used to obtain energy-resolved spectra of scattered ions at {theta}{sub i} = {theta}{sub f} = 45 deg. These results are compared to the classical trajectory simulation SAFARI and show features indicative of light atom-surface scattering where sequential binary collisions can describe the observed energy loss spectra. Energy-resolved spectra obtained for Cs{sup +} ions at incident energies of 75 eV and 200 eV also show features consistent with binary collisions. However, for this heavy atom-surface scattering system, the dominant trajectory type involves at least two surface atoms, as large angular deflections are not classically allowed for any single scattering event. In addition, a significant deviation from the classical double-collision prediction is observed for incident energies around 100 eV, and molecular dynamics studies are proposed to investigate the role of collective lattice effects. Data are also presented for the scattering of K{sup +} ions from a Schottky diode structure, which is a prototype device for the development of active targets to probe energy loss at a surface.

The effect of soil properties on the toxicity and bioaccumulation of Ag nanoparticles and Ag ions in Enchytraeus crypticus.

Science.gov (United States)

Topuz, Emel; van Gestel, Cornelis A M

2017-10-01

Standard natural Lufa soils (2.2, 2.3 and 5M) with different organic carbon contents (0.67-1.61%) and pH CaCl2 (5.5-7.3) were spiked with ionic Ag (AgNO 3 ) and polyvinyl pyrrolidone (AgNP-PVP) and citrate (AgNP-Cit) coated Ag nanoparticles (NPs). Enchytraeus crypticus were exposed for 21 days to assess effects on survival and reproduction. Soil, pore water and animals were analyzed for Ag. AgNP-Cit had a strong increasing effect on soil pH, leading to high enchytraeid mortality at concentrations higher than 60-100mg Ag/kg dry soil which made it impossible to determine the influence of soil properties on its toxicity. LC50s were lower for AgNO 3 than for AgNP-PVP (92-112 and 335-425mg Ag/kg dry soil, respectively) and were not affected by soil properties. AgNO 3 and AgNP-PVP had comparable reproductive toxicity with EC50s of 26.9-75.2 and 28.2-92.3mg Ag/kg dry soil, respectively; toxicity linearly increased with decreasing organic carbon content of the soils but did not show a clear effect of soil pH. Ag uptake in the enchytraeids was higher at higher organic carbon content, but could not explain differences in toxicity between soils. This study indicates that the bioavailability of both ionic and nanoparticulate Ag is mainly affected by soil organic carbon, with little effect of soil pH. Copyright © 2017. Published by Elsevier Inc.

Changes in biogenic amine concentrations in meat of eviscerated pheasants (Phasianus colchicus during storage at 7 °C

Directory of Open Access Journals (Sweden)

Zdeňka Hutařová

2013-01-01

Full Text Available In our study, we tested biogenic amine concentrations in 20 eviscerated pheasants killed by pithing (the slaughtering technique in which the spinal cord of the animals is severed and their brain is destroyed and stored at 7 °C for 21 days. Biogenic amine concentrations in breast and thigh muscles were analysed by reverse phase liquid chromatography. In the thigh muscle, the highest increases during the storage time were found in cadaverine (20.17 ± 18.66 mg/kg, putrescine (4.39 ± 4.17 mg/kg and tyramine (15.20 ± 16.88 mg/kg concentrations. Changes of biogenic amine concentrations in the breast muscle were minimal during the whole storage time. The concentration of biogenic amines in meat is associated with the presence of contaminating microorganisms. For that reason, biogenic amines are often used as markers of meat spoilage in various livestock species. Based on our results, the biogenic amines cadaverine, putrescine and tyramine may be considered the main indicators of hygienic quality of pheasant meat. We can recommend storing pithed pheasants treated by evisceration no longer than for seven days at 7 °C. After that period, biogenic amine concentrations in meat begin to change. The main significance of this study lies in the extension of the lack information about the content of biogenic amines in the meat of eviscerated pithed pheasant and also about changes of their concentrations during the course of storage.

Interfacial properties of the enhanced visible-light plasmonic Ag/Bi{sub 2}WO{sub 6} (0 0 1) nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Wang, Fang [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu 610500 (China); The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, Chengdu 610500 (China); Cao, Kun; Wu, Yi [The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, Chengdu 610500 (China); Zhang, Kun-Hao [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201204 (China); Zhou, Ying, E-mail: yzhou@swpu.edu.cn [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu 610500 (China); The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, Chengdu 610500 (China)

2016-01-01

Graphical abstract: - Highlights: • The parallel adsorption of silver on Bi{sub 2}WO{sub 6} (0 0 1) makes energetically favorable configurations. The positive charged Ag cluster may act as excited electron traps. • New isolated levels appear above the valence bands due to the hybridization of Ag 5s and O 2p, and they become dispersed as Ag content increases. This is responsible for the improved visible-light response. • Optical spectra confirm obvious red-shifts of the absorption edge with the increment of silver content, which enhances efficiently the photocatalytic activity of Bi{sub 2}WO{sub 6} (0 0 1). - Abstract: First principle calculations are performed to study the interfacial photoelectric properties of Ag{sub n}/Bi{sub 2}WO{sub 6} (0 0 1) (n = 1, 2, 3, 4) hybrid photocatalyst. The parallel adsorption of Ag cluster leads to more energetic favorable structures due to stronger interfacial interactions. The positive charged Ag cluster may act as excited electron traps and facilitate the electron–hole separation. In particular, hybridization between Ag 5s and O 2p leads to the formation of isolated energy levels above the valence bands, and they become more dispersed with broader bandwidth with the increment of silver cluster size, which is responsible for the enhanced absorption in visible-light region. In the deep valence region, Ag 4d orbital turns more delocalized and hybrid with O 2p states as the cluster size increases, which contributes to more covalent bond feature of Ag–O. Moreover, optical spectra demonstrate obvious red-shifts of the absorption edge with the increment of silver content, which enhances efficiently the visible-light photocatalytic activities of Bi{sub 2}WO{sub 6} (0 0 1). The study provides insights into the enhanced photocatalyic mechanism of Ag/Bi{sub 2}WO{sub 6} (0 0 1) and aids in the design of noble metal loaded visible-light plasmonic photocatalyst.

Composite cathode La0.15Bi0.85O1.5-Ag for intermediate-temperature solid oxide fuel cells

International Nuclear Information System (INIS)

Gao Zhan; Mao Zongqiang; Huang Jianbing; Gao Ruifeng; Wang Cheng; Liu Zhixiang

2008-01-01

Composites consisting of silver and lanthanum stabilized bismuth oxide (La 0.15 Bi 0.85 O 1.5 ) were investigated as cathodes for intermediate-temperature solid oxide fuel cells with doped ceria as electrolyte. No stable phases were formed via reaction between La 0.15 Bi 0.85 O 1.5 and Ag. The microstructure of the interfaces between composite cathodes and Ce 0.8 Sm 0.2 O 1.5 electrolytes was studied by scanning electron microscopy after sintering at various temperatures. Impedance spectroscopy measurements revealed that the performance of cathode fired at 700 deg. C was the best. When the optimum fraction of Ag was 50 vol.%, polarization resistance values for the LSB-Ag50 cathode were as low as 0.14 Ω cm 2 at 700 deg. C and 0.18 Ω cm 2 at 650 deg. C. The steady-state polarization investigations on LSB and LSB-Ag50 cathodes were performed using typical three-electrode test cells in air. The results showed that the LSB-Ag50 composite cathode exhibited a lower overpotential and higher exchange current density than LSB, which indicated the electrochemical performance of LSB-Ag50 for the oxygen reduction reaction was superior to the LSB

Control of texture in Ag and Ag-alloy substrates for superconducting tapes

International Nuclear Information System (INIS)

Gladstone, T.A.

2000-01-01

The use of a biaxially textured silver tape as a substrate for high temperature superconductor (HTS) phases is one possible route towards the fabrication of high-J c superconducting tape. Using a cold-rolling and annealing process we have reproducibly fabricated {110} textured silver which is stable up to 900 deg. C. We have found that there are two critical process requirements for the formation of this texture; a low oxygen content in the material prior to deformation, and a cold-rolling thickness reduction of less than 97%. To overcome the problems associated with the poor mechanical strength of pure silver, texture development in Ag-Mg and Ag-Hf alloys with improved mechanical properties has been studied. Heat treatments in a reducing atmosphere allow the {110} annealing texture to be obtained in Ag-0.1 wt%Mg. The recrystallization behaviour of a Ag-Pd alloy with an increased stacking fault energy was also investigated and a partial cube texture was obtained in this material. Using orientation distribution function (ODF) analysis we have shown that minor variations in the deformation texture of both pure silver and Ag-based alloys can lead to significant differences in the recrystallization textures obtained. (author)

Tuning the work function of VO_2(1 0 0) surface by Ag adsorption and incorporation: Insights from first-principles calculations

International Nuclear Information System (INIS)

Chen, Lanli; Wang, Xiaofang; Shi, Siqi; Cui, Yuanyuan; Luo, Hongjie; Gao, Yanfeng

2016-01-01

Graphical abstract: - Highlights: • After adsorption, there is a charge transfer from Ag to VO_2(1 0 0) surface, which thus increases the electron concentration in VO_2 thin film. • Ag adsorption on VO_2(1 0 0) surface process is an exothermic chemical process, and the adsorption system is stable. • The work function can be tuned by Ag adsorption on and incorporation into the VO_2(1 0 0) surface, which in turn regulates the phase transition temperature of VO_2. - Abstract: VO_2 is an attractive material for application to thermochromic optoelectronic devices such as smart windows, and Ag/VO_2 double-layered structure can effectively decrease the phase transition temperature (T_c) of VO_2 thin film, which is very important for practical application of VO_2. Previous works has shown that the decrease in phase transition temperature (T_c) seems to be relevant with the work function of VO_2 in Ag/VO_2 double-layered thin film, although the underlying mechanism of tuning its T_c by Ag incorporation and adsorption on the VO_2(1 0 0) surface has been rarely investigated. Our first-principles calculations reveal that the adsorption of Ag atoms on the VO_2(1 0 0) surface rather than incorporation of Ag exhibits a lower work function, which is ascribed to an integrated effect of charge transfer from Ag to VO_2(1 0 0) surface and enhanced surface dipole moment. The results suggest that the decrease in work function of VO_2 with Ag adsorption favors the reduction in T_c. The current findings are helpful to understand the fundamental mechanism for yielding high-efficiency VO_2-based optoelectronic devices.

ANTIMICROBIAL ACTIVITY OF Ag+, Cu2+, Zn2+, Mg2+ IONS DOPED CHITOSAN NANOPARTICLES

Directory of Open Access Journals (Sweden)

Sukhodub LB

2015-04-01

Full Text Available Modification by polymers and inorganic ions of the bioactive materials for orthopedic implants with the purpose of initiating controlled reactions in tissues that surround the implant, is one of the modern approaches in medical materials. A key feature of functional polymers is their ability to form complexes with various metal ions in solution. Chitosan is natural biopolymer with pronounced affinity to transition metal ions. Some researches prove the higher antimicrobial activity of Chitosan-metal complexes compared with pure Chitosan. The purpose of this work was the study of antimicrobial activity of Chitosan nanoparticles modified by metal ions Ag+, Cu2+, Zn2+, Mg2+ against reference strains S. aureus 25923 ATSS, E. coli ATCC 25922, C. albicans ATCC 885653 for their further use as components of the composite biomaterials for medical purpose.Chitosan nanoparticles suspension was prepared by known method based on the ionotropic gelation between chitosan and sodium tripolyphosphate.To obtain Chitosan-metal nanoparticles to the Chitosan suspension were added the corresponding metal ions aqueous solutions in quantity to match the concentration of metal ions of 200 ppm . Antibacterial activities of Ag+, Cu2+, Zn2+, Mg2+ ions doped Chitosan nanoparticles, pure Chitosan nanoparticles, metal ions and 1% (v/v acetic acid solution (it was used as solvent for Chitosan against bacteria were evaluated by determination of minimum inhibitory concentration (MIC and minimum bactericidal concentration (MBC in vitro. Muller– Hinton (MH broth and MH agar (Russia were used as growth media. The bacteria suspension for further use was prepared with concentration that corresponded 0,5units by McFarland scale. The MIC was determined by a broth dilution method. The results were read after 24 hours of experimental tubes incubation at 37 oC as equivalent to the concentration of the tube without visible growth. To evaluate MBC, a sample of 0,1 ml was transferred from

Reprint of “Theoretical description of metal/oxide interfacial properties: The case of MgO/Ag(001)”

Energy Technology Data Exchange (ETDEWEB)

Prada, Stefano [Dipartimento di Scienza dei Materiali, Università di Milano-Bicocca, via R. Cozzi, 53, 20125 Milano (Italy); Giordano, Livia, E-mail: livia.giordano@mater.unimib.it [Dipartimento di Scienza dei Materiali, Università di Milano-Bicocca, via R. Cozzi, 53, 20125 Milano (Italy); Pacchioni, Gianfranco [Dipartimento di Scienza dei Materiali, Università di Milano-Bicocca, via R. Cozzi, 53, 20125 Milano (Italy); Goniakowski, Jacek [CNRS-Sorbonne Universités UPMC Univ. Paris 06, UMR 7588, INSP, F-75005 Paris (France)

2017-02-28

Highlights: • Characteristics of Ag-supported MgO(100) films are studied with different DFT functionals. • All approaches predict a similar nature of supported pristine and oxygen-deficient films. • Interface distances and adhesion are particularly sensitive to the choice of the approximation. • Satisfactory matching with the experiment is obtained with the DFT-optB88 functional. • Charge transfer, work function and vacancy characteristics are little influenced by the method. - Abstract: We compare the performances of different DFT functionals applied to ultra-thin MgO(100) films supported on the Ag(100) surface, a prototypical system of a weakly interacting oxide/metal interface, extensively studied in the past. Beyond semi-local DFT-GGA approximation, we also use the hybrid DFT-HSE approach to improve the description of the oxide electronic structure. Moreover, to better account for the interfacial adhesion, we include the van de Waals interactions by means of either the semi-empirical force fields by Grimme (DFT-D2 and DFT-D2*) or the self-consistent density functional optB88-vdW. We compare and discuss the results on the structural, electronic, and adhesion characteristics of the interface as obtained for pristine and oxygen-deficient Ag-supported MgO films in the 1–4 ML thickness range.

On Mineral Retrosynthesis of a Complex Biogenic Scaffold

Directory of Open Access Journals (Sweden)

Ashit Rao

2017-03-01

Full Text Available Synergistic relations between organic molecules and mineral precursors regulate biogenic mineralization. Given the remarkable material properties of the egg shell as a biogenic ceramic, it serves as an important model to elucidate biomineral growth. With established roles of complex anionic biopolymers and a heterogeneous organic scaffold in egg shell mineralization, the present study explores the regulation over mineralization attained by applying synthetic polymeric counterparts (polyethylene glycol, poly(acrylic acid, poly(aspartic acid and poly(4-styrenesulfonic acid-co-maleic acid as additives during remineralization of decalcified eggshell membranes. By applying Mg2+ ions as a co-additive species, mineral retrosynthesis is achieved in a manner that modulates the polymorph and structure of mineral products. Notable features of the mineralization process include distinct local wettability of the biogenic organic scaffold by mineral precursors and mineralization-induced membrane actuation. Overall, the form, structure and polymorph of the mineralization products are synergistically affected by the additive and the content of Mg2+ ions. We also revisit the physicochemical nature of the biomineral scaffold and demonstrate the distinct spatial distribution of anionic biomolecules associated with the scaffold-mineral interface, as well as highlight the hydrogel-like properties of mammillae-associated macromolecules.

Microstructure and magnetic properties of FePt:Ag nanocomposite films on SiO2/Si(1 0 0)

International Nuclear Information System (INIS)

Wang Hao; Yang, F.J.; Wang, H.B.; Cao, X.; Xue, S.X.; Wang, J.A.; Gao, Y.; Huang, Z.B.; Yang, C.P.; Chiah, M.F.; Cheung, W.Y.; Wong, S.P.; Li, Q.; Li, Z.Y.

2006-01-01

FePt:Ag nanocomposite films were prepared by pulsed filtered vacuum arc deposition system and subsequent rapid thermal annealing on SiO 2 /Si(1 0 0) substrates. The microstructure and magnetic properties were investigated. A strong dependence of coercivity and ordering of the face-central tetragonal structure on both Ag concentration and annealing temperature was observed. With Ag concentration of 22% in atomic ratio, the coercivity got to 6.0 kOe with a grain size of 6.7 nm when annealing temperature was 400 deg. C

Density functional theory study of hydrogenation mechanism in Fe-doped Mg(0 0 0 1) surface

International Nuclear Information System (INIS)

Wu Guangxin; Zhang Jieyu; Wu Yongquan; Li Qian; Chou Kuochih; Bao Xinhua

2009-01-01

Using density functional theory (DFT) in combination with nudged elastic band (NEB) method, the dissociative chemisorptions and diffusion processes of hydrogen on both pure and Fe-doped Mg(0 0 0 1) surfaces are studied. Firstly, the dissociation pathway of H 2 and the relative barrier were investigated. The calculated dissociation barrier (1.08 eV) of hydrogen molecule on a pure Mg(0 0 0 1) surface is in good agreement with comparable experimental and theoretical studies. For the Fe-doped Mg(0 0 0 1) surface, the activated barrier decreases to 0.101 eV due to the strong interaction between the s orbital of H and the d orbital of Fe. Then, the diffusion processes of atomic hydrogen on pure and Fe-doped Mg(0 0 0 1) are presented. The obtained diffusion barrier to the first subsurface is 0.45 eV and 0.98 eV, respectively. Finally, Chou method was used to investigate the hydrogen sorption kinetic mechanism of pure MgH 2 and Mg mixed with 5 at.% Fe atoms composites. The obtained activation energies are 0.87 ± 0.02 and 0.31 ± 0.01 eV for H 2 dissociation on the pure surface and H atom diffusion in Fe-doped Mg surfaces, respectively. It suggests that the rate-controlling step is dissociation of H 2 on the pure Mg surface while it is diffusion of H atom in the Fe-doped Mg surface. And both of fitting data are matching well with our calculation results.

First-principles study of Sb adsorption on Ag(1 1 0)(2 x 2)

International Nuclear Information System (INIS)

Nie, J.L.; Xiao, H.Y.; Zu, X.T.; Gao Fei

2006-01-01

The adsorption of antimony atom on the Ag(1 1 0) surface has been studied within the density functional theory framework. It was turned out that Sb-Ag surface alloy was formed in which Sb atoms substitute Ag atom in the outermost layer and subsurface site absorption was not preferred, suggesting that Sb is well segregated to the surface. Geometric analysis showed that rumpling between substitutional Sb and Ag in the alloy surface is negligible. These results are found to agree well with the experimental finding of Nascimento et al. [Surf. Sci. 572 (2004) 337]. In addition, investigation of the diffusion of Ag atom on bare and Sb-covered Ag(1 1 0) surface showed that Ag adatoms will jump along the so call in-channel direction and Sb substitution has little effect on the diffusion of Ag adatoms on Ag(1 1 0) surface. Such diffusion behavior was found to be different from that of Ag adatoms on Ag(1 1 1) surface, where the diffusion energy barrier was reported to be significantly increased upon Sb substitution [Phys. Rev. Lett. 73 (1993) 2437

Effect of salt-tolerant yeast of Candida versatilis and Zygosaccharomyces rouxii on the production of biogenic amines during soy sauce fermentation.

Science.gov (United States)

Qi, Wei; Hou, Li-Hua; Guo, Hong-Lian; Wang, Chun-Ling; Fan, Zhen-Chuan; Liu, Jin-Fu; Cao, Xiao-Hong

2014-06-01

This study aimed to enhance and improve the quality and safety of soy sauce. In the present work, the change of biogenic amines, such as histamine, tyramine, cadaverine, spermidine, was examined by the treatment of Candida versatilis and Zygosaccharomyces rouxii, and the influence of salt-tolerant yeast on biogenic amines was analysed during the whole fermentation process. The results showed that the content of biogenic amines was elevated after yeast treatment and the content of biogenic amines was influenced by using yeast. The dominating biogenic amine in soy sauce was tyramine. At the end of fermentation, the concentrations of biogenic amines produced by Zygosaccharomyces rouxii and Candida versatilis in the soy mash were 122.71 mg kg(-1) and 69.96 mg kg(-1) . The changes of biogenic amines in high-salt liquid soy mash during fermentation process indicated that a variety of biogenic amines were increased in the fermentation ageing period, which may be due to amino acid decarboxylation to form biogenic amines by yeast decarboxylase. The fermentation period of soy sauce should be longer than 5 months because biogenic amines began to decline after this time period. © 2013 Society of Chemical Industry.

Biogenic synthesis, characterization of silver nanoparticles using multani mitti (fullers earth), tomato (solanum lycopersicum) seeds, rice husk (oryza sativa) and evaluation of their potential antimicrobial activity

International Nuclear Information System (INIS)

Dar, P.; Hina, A.; Anwar, J.

2016-01-01

The synthesis of silver nanoparticles of three different biogenic materials Multani mitti (Fullers earth), Tomato (Solanum lycopersicum) seeds, Rice Husk (Oryza sativa) was carried out. The possible presence and variability of comprehensive biomolecules in these materials turned as capping and reducing agents which optimize the reduction rate and stabilization of silver nanoparticles. Characterizations were determined by using ultraviolet-visible (UV-Vis) spectroscopy, Scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). Stable silver nanoparticles of average size 4.6, 41.1 and 10.6 nm were obtained for Multani mitti, tomato seeds and rice husk respectively. Phenolic and carboxylic biomolecules were identified as active reducing agents of Ag+2 to Ag0. The antimicrobial activity was carried out against Klebsiella pneumonia, Salmonella enterica, Escherichia coli and Staphylococcus aureus strains by using well diffusion method. Maximum zone of inhibition (ZOI) was found against Staphylococcus aureus by all of the three biogenic materials. (author)

Transport properties of S0.8Se16M0.2 (M = Al, Ag or Cu) system

International Nuclear Information System (INIS)

Wahab, L.A.

2003-01-01

The results are presented of a study of the electrical and optical properties of vacuum evaporated amorphous thin films in the S 0.8 Se 16 M 0.2 (M=Al, Ag or Cu) system. The activation energy and the pre-exponential factor which appear in the dc conductivity are found to be higher in case of Cu than in case of Ag and Al. The reflectance and transmission are used to measure the optical gap. The glass S 0.8 Se 16 Cu 0.2 behaves as a quasi intrinsic semiconductor (the electrical activation energy is about half of the optical gap). The electrical activation energy is about one-third of the optical gap for the chalcogenide glasses S 0.8 Se 16 Al 0.2 and S 0.8 Se 16 Ag 0.2 . The variation in the refractive index and the imaginary part of the dielectric constant with photon energy have also been reported. The influence of composition on the investigated parameters is reported

Hot deformation of particulate reinforced Al-4Li-1Mg-0.5Ge-0.2Zr

International Nuclear Information System (INIS)

Chanda, T.; Lavernia, E.J.; Wolfenstine, J.

1991-01-01

Lithium additions to aluminum give the greatest reduction in density and increase in elastic modulus per wt.% of any known alloying element. The potential for aluminum alloy density reduction through lithium additions is evident by comparing its atomic weight (6.94) to that of aluminum (26.98). Over the past decade, considerable research efforts have been directed towards developing aluminum-lithium alloys, with lithium contents of up to 2.5 wt.%, for aircraft applications, where their low density and increased stiffness can lead to significant improvements in payload capacity. A recent notable example has been the development of a quarternary aluminum-lithium alloy containing silver, (A1-(4.5-6.3) Cu-1.3Li-0.4Ag-0.4Mg-0.14Zr, in wt.%). In an effort to further decrease the density and increase the modulus of aluminum-lithium alloys, research efforts have progressively shifted towards alloys containing higher concentrations of lithium (>3.0 wt.%). Furthermore, aluminum-lithium alloys are being studied as potential candidate matrix materials in metal matrix composites (MMCs), as a result of the observation that lithium effectively enhances the ability of the aluminum matrix to wet the ceramic reinforcement. The extreme reactivity associated with high additions of lithium, and the difficulties associated with processing MMCs, have prompted the development of alternate synthesis approaches. One such approach, spray atomization and co-deposition, is actively being studied as a result of its ability to rapidly quench, reinforce, and consolidate in a single step, thus avoiding the difficulties associated with the handling of fine reactive particulates. The object of the paper is to provide insight into the elevated temperature deformation behavior of high lithium (4 wt.%) aluminum alloys reinforced with SiC particles prepared by spray atomization and co-deposition. The selection of the A1-4Li-1Mg-0.5Ge-0.2Zr wt

Colossal magnetoresistance of bulk Ag-doped Nd{sub 0.7}Sr{sub 0.3}MnO{sub 3} two-phase composites

Energy Technology Data Exchange (ETDEWEB)

Cui Xugao [National Laboratory of Solid State Microstructures, Department of Physics, Nanjing University, Nanjing 210093 (China); Hu Xiukun [National Laboratory of Solid State Microstructures, Department of Physics, Nanjing University, Nanjing 210093 (China); Xia Hongxu [National Laboratory of Solid State Microstructures, Department of Physics, Nanjing University, Nanjing 210093 (China); Yu Jiangying [National Laboratory of Solid State Microstructures, Department of Physics, Nanjing University, Nanjing 210093 (China); Zhang Shiyuan [National Laboratory of Solid State Microstructures, Department of Physics, Nanjing University, Nanjing 210093 (China)]. E-mail: zsy@netra.nju.edu.cn

2005-05-17

We have prepared a series of bulk polycrystalline manganites with the nominal compositions, Nd{sub 0.7}Sr{sub 0.3}MnO{sub 3}-Ag {sub x} (x is the molar fraction) with x = 0.1, 0.2, 0.3, 0.4, 0.5 by conventional solid-state reaction. The X-ray diffraction patterns show that the sample Nd{sub 0.7}Sr{sub 0.3}MnO{sub 3} (x = 0) is a single-phase compound with the pseudocubic perovskite structure, while the Ag-doped samples are two-phase composites consisting of a ferromagnetic perovskite phase and a nonmagnetic Ag metal phase. For all the samples, the Curie temperature, T {sub C}, remains nearly the same (228 {+-} 2 K), but the maximum magnetoresistance in a magnetic field of 1 T at 222 K is enhanced strongly due to the addition of Ag, namely, from 45% for the Nd{sub 0.7}Sr{sub 0.3}MnO{sub 3} sample to 188, 277, 142, 158 and 151% for the Nd{sub 0.7}Sr{sub 0.3}MnO{sub 3}-Ag {sub x} samples with x = 0.1, 0.2, 0.3, 0.4, and 0.5, respectively. This magnetoresistance-enhancement phenomenon can be attributed to the spin-dependent scattering of the spin-polarized electrons at the interfaces between the perovskite grains and the Ag granules.

Tuning the work function of VO{sub 2}(1 0 0) surface by Ag adsorption and incorporation: Insights from first-principles calculations

Energy Technology Data Exchange (ETDEWEB)

Chen, Lanli; Wang, Xiaofang [School of Materials Science and Engineering, Shanghai University, Shanghai 200444 (China); Shi, Siqi, E-mail: sqshi@shu.edu.cn [School of Materials Science and Engineering, Shanghai University, Shanghai 200444 (China); Materials Genome Institute, Shanghai University, Shanghai 200444 (China); Cui, Yuanyuan [School of Materials Science and Engineering, Shanghai University, Shanghai 200444 (China); Luo, Hongjie [School of Materials Science and Engineering, Shanghai University, Shanghai 200444 (China); Materials Genome Institute, Shanghai University, Shanghai 200444 (China); Gao, Yanfeng, E-mail: yfgao@shu.edu.cn [School of Materials Science and Engineering, Shanghai University, Shanghai 200444 (China)

2016-03-30

Graphical abstract: - Highlights: • After adsorption, there is a charge transfer from Ag to VO{sub 2}(1 0 0) surface, which thus increases the electron concentration in VO{sub 2} thin film. • Ag adsorption on VO{sub 2}(1 0 0) surface process is an exothermic chemical process, and the adsorption system is stable. • The work function can be tuned by Ag adsorption on and incorporation into the VO{sub 2}(1 0 0) surface, which in turn regulates the phase transition temperature of VO{sub 2}. - Abstract: VO{sub 2} is an attractive material for application to thermochromic optoelectronic devices such as smart windows, and Ag/VO{sub 2} double-layered structure can effectively decrease the phase transition temperature (T{sub c}) of VO{sub 2} thin film, which is very important for practical application of VO{sub 2}. Previous works has shown that the decrease in phase transition temperature (T{sub c}) seems to be relevant with the work function of VO{sub 2} in Ag/VO{sub 2} double-layered thin film, although the underlying mechanism of tuning its T{sub c} by Ag incorporation and adsorption on the VO{sub 2}(1 0 0) surface has been rarely investigated. Our first-principles calculations reveal that the adsorption of Ag atoms on the VO{sub 2}(1 0 0) surface rather than incorporation of Ag exhibits a lower work function, which is ascribed to an integrated effect of charge transfer from Ag to VO{sub 2}(1 0 0) surface and enhanced surface dipole moment. The results suggest that the decrease in work function of VO{sub 2} with Ag adsorption favors the reduction in T{sub c}. The current findings are helpful to understand the fundamental mechanism for yielding high-efficiency VO{sub 2}-based optoelectronic devices.

Patch testing with 2.0% (0.60 mg/cm2) formaldehyde instead of 1.0% (0.30 mg/cm2) detects significantly more contact allerg

DEFF Research Database (Denmark)

Pontén, Ann; Aalto-Korte, Kristiina; Agner, Tove

2013-01-01

.To validate earlier patch test results for comparison of 1% (wt/vol) and 2% (wt/vol) formaldehyde in water, and to investigate co-reactivity with quaternium-15. Materials and methods.In 12 dermatology clinics, 3591 patients were routinely patch tested simultaneously with 2.0% (wt/vol) (0.60 mg/cm(2) ) and 1.......0% (wt/vol) (0.30 mg/cm(2) ) formaldehyde. Micropipettes were used for delivering the exact dosage of the allergen. Results.Significantly more patients reacted to 2.0% formaldehyde than to 1.0% (3.4% versus 1.8%, p

Thermoelectric properties of p-type pseudo-binary (Ag0.365Sb0.558Te) x -(Bi0.5Sb1.5Te3)1-x (x=0-1.0) alloys prepared by spark plasma sintering

International Nuclear Information System (INIS)

Cui, J.L.; Xue, H.F.; Xiu, W.J.; Jiang, L.; Ying, P.Z.

2006-01-01

In this paper, pseudo-binary (Ag 0.365 Sb 0.558 Te) x -(Bi 0.5 Sb 1.5 Te 3 ) 1- x (x=0-1.0) alloys were prepared using spark plasma sintering technique, and the composition-dependent thermoelectric properties were evaluated. Electrical conductivities range from 7.9x10 4 to 15.6x10 4 Ω -1 m -1 at temperatures of 507 and 318 K, respectively, being about 3.0 and 8.5 times those of Bi 0.5 Sb 1.5 Te 3 alloy at the corresponding temperatures. The optimal dimensionless figure of merit (ZT) of the sample with molar fraction x=0.025 reaches 1.1 at 478 K, whereas that of the ternary Bi 0.5 Sb 1.5 Te 3 alloy is 0.58 near room temperature. The results also reveal that a direct introduction of Ag 0.365 Sb 0.558 Te in the Bi-Sb-Te system is much more effective to the property improvement than naturally precipitated Ag 0.365 Sb 0.558 Te in the Ag-doped Ag-Bi-Sb-Te system. - Graphical abstract: The temperature dependence of the dimensionless thermoelectric figure of merit ZT for different (Ag 0.365 Sb 0.558 Te) x -(Bi 0.5 Sb 1.5 Te 3 ) 1- x (x=0-1.0) alloys prepared by spark plasma sintering

Elastic, vibration and thermodynamic properties of Cu1‑x Ag x InTe2 (x = 0, 0.25, 0.5, 0.75 and 1) chalcopyrite compounds via first principles

Science.gov (United States)

Zhong, Yuhan; Wang, Peida; Mei, Huayue; Jia, Zhenyuan; Cheng, Nanpu

2018-06-01

CuInTe2 chalcopyrite compound is widely used in the fields of optoelectronics and pyroelectricity, and doping atoms can further improve the physical properties of the CuInTe2 compound. For all we know, this is the first time that the elastic behaviors and lattice dynamical properties of Ag-doped CuInTe2 compounds with the tetragonal system are determined theoretically. The elastic, lattice dynamical and thermal properties of Cu1‑x Ag x InTe2 (x = 0, 0.25, 0.5, 0.75 and 1) compounds have been investigated by using density functional theory. The obtained elastic constants of Cu1‑x Ag x InTe2 compounds indicate that these compounds are mechanically stable and elastic anisotropic. The anisotropy of the {001} plane is more obvious than those of the {100} and {010} planes. Additionally, with increasing Ag doping concentrations, the bulk and shear moduli of Cu1‑x Ag x InTe2 compounds decrease and their toughness improves. The phonon spectra and density of states reveal that Cu (or Ag) atoms in Cu1‑x Ag x InTe2 compounds form chemical bonds with Te atoms, and Cu-Te bonds are gradually replaced by Ag-Te bonds with increasing Ag doping concentration. Vibration modes of Cu1‑x Ag x InTe2 compounds at the {{Γ }} point in the Brillouin zone show that each Cu1‑x Ag x InTe2 (x = 0 and 1) crystal includes five irreducible representations (A1, A2, B1, B2 and E). As for Cu1‑x Ag x InTe2 (x = 0.25, 0.5 and 0.75) compounds, each crystal has three irreducible representations (A, B and E). The atomic displacements of several typical phonon modes in CuInTe2 crystals have been analyzed to deepen the understanding of lattice vibrations in Cu1‑x AgxInTe2 compounds. With increasing Ag doping concentration, the Debye temperatures of Cu1‑x Ag x InTe2 compounds decrease, while their heat capacities increase.

Quantitative transmission electron microscopy and atom probe tomography study of Ag-dependent precipitation of Ω phase in Al-Cu-Mg alloys

Energy Technology Data Exchange (ETDEWEB)

Bai, Song; Ying, Puyou [Key Laboratory of Nonferrous Metal Materials Science and Engineering, Ministry of Education, Central South University, Changsha 410083 (China); School of Material Science and Engineering, Central South University, Changsha 410083 (China); Liu, Zhiyi, E-mail: liuzhiyi@csu.edu.cn [Key Laboratory of Nonferrous Metal Materials Science and Engineering, Ministry of Education, Central South University, Changsha 410083 (China); School of Material Science and Engineering, Central South University, Changsha 410083 (China); Wang, Jian; Li, Junlin [Key Laboratory of Nonferrous Metal Materials Science and Engineering, Ministry of Education, Central South University, Changsha 410083 (China); School of Material Science and Engineering, Central South University, Changsha 410083 (China)

2017-02-27

The close association between the Ω precipitation and various Ag additions is systematically investigated by quantitative transmission electron microscopy and atom probe tomography analysis. Our results suggest that the precipitation of Ω phase is strongly dependent on Ag variations. Increasing the bulk Ag content favors a denser Ω precipitation and hence leads to a greater age-hardening response of Al-Cu-Mg-Ag alloy. This phenomenon, as proposed by proximity histograms, is directly related to the greater abundance of Ag solutes within Ω precursors. This feature lowers its nucleation barrier and increases the nucleation rate of Ω phase, finally contributes to the enhanced Ω precipitation. Also, it is noted that increasing Ag remarkably restricts the precipitation of θ' phase.

Growth of Ag thin films on ZnO(0 0 0 -1) investigated by AES and STM

Energy Technology Data Exchange (ETDEWEB)

Duriau, E. [Interuniversity Microelectronic Center (IMEC), SPDT-MCA, Kapeldreef 75, B-3001 Leuven (Belgium); Agouram, S. [Dpto. Fisica Aplicada y Electromagnetismo c/Dr. Moliner no. 50, 46100 Burjassot, Valencia (Spain); Laboratoire de Physique des Materiaux Electroniques (LPME), University of Namur, Rue de Bruxelles 61, B-5000 Namur (Belgium); Morhain, C. [Centre de Recherche sur l' HeteroEpitaxie et ses Applications (CRHEA), CNRS, Rue Bernard Gregory, F-06560 Valbonne Sophia-Antipolis (France); Seldrum, T. [Laboratoire de Physique des Materiaux Electroniques (LPME), University of Namur, Rue de Bruxelles 61, B-5000 Namur (Belgium); Sporken, R. [Laboratoire de Physique des Materiaux Electroniques (LPME), University of Namur, Rue de Bruxelles 61, B-5000 Namur (Belgium); Dumont, J. [Laboratoire de Physique des Materiaux Electroniques (LPME), University of Namur, Rue de Bruxelles 61, B-5000 Namur (Belgium)]. E-mail: jacques.dumont@fundp.ac.be

2006-11-15

The growth of Ag films on ZnO(0 0 0 -1) has been investigated by Auger electron spectroscopy (AES) and scanning tunneling microscopy (STM). A high density of islands is nucleated at the earliest stages of the growth. An upstepping mechanism causes these islands to coalesce while the uncovered fraction of the ZnO surface remains constant (30%)

Framework for Assessing Biogenic CO2 Emissions from ...

Science.gov (United States)

This revision of the 2011 report, Accounting Framework for Biogenic CO2 Emissions from Stationary Sources, evaluates biogenic CO2 emissions from stationary sources, including a detailed study of the scientific and technical issues associated with assessing biogenic carbon dioxide emissions from stationary sources. EPA developed the revised report, Framework for Assessing Biogenic CO2 Emissions from Stationary Sources, to present a methodological framework for assessing the extent to which the production, processing, and use of biogenic material at stationary sources for energy production results in a net atmospheric contribution of biogenic CO2 emissions. Biogenic carbon dioxide emissions are defined as CO2 emissions related to the natural carbon cycle, as well as those resulting from the production, harvest, combustion, digestion, decomposition, and processing of biologically-based materials. The EPA is continuing to refine its technical assessment of biogenic CO2 emissions through another round of targeted peer review of the revised study with the EPA Science Advisory Board (SAB). This study was submitted to the SAB's Biogenic Carbon Emissions Panel in February 2015. http://yosemite.epa.gov/sab/sabproduct.nsf/0/3235dac747c16fe985257da90053f252!OpenDocument&TableRow=2.2#2 The revised report will inform efforts by policymakers, academics, and other stakeholders to evaluate the technical aspects related to assessments of biogenic feedstocks used for energy at s

Enhanced brightness of organic light-emitting diodes based on Mg:Ag cathode using alkali metal chlorides as an electron injection layer

International Nuclear Information System (INIS)

Zou Ye; Deng Zhenbo; Xu Denghui; Lü Zhaoyue; Yin Yuehong; Du Hailiang; Chen Zheng; Wang Yongsheng

2012-01-01

Different thicknesses of cesium chloride (CsCl) and various alkali metal chlorides were inserted into organic light-emitting diodes (OLEDs) as electron injection layers (EILs). The basic structure of OLED is indium tin oxide (ITO)/N,N′-diphenyl-N,N′-bis(1-napthyl-phenyl)-1.1′-biphenyl-4.4′-diamine (NPB)/tris-(8-hydroxyquinoline) aluminum (Alq 3 )/Mg:Ag/Ag. The electroluminescent (EL) performance curves show that both the brightness and efficiency of the OLEDs can be obviously enhanced by using a thin alkali metal chloride layer as an EIL. The electron injection barrier height between the Alq 3 layer and Mg:Ag cathode is reduced by inserting a thin alkali metal chloride as an EIL, which results in enhanced electron injection and electron current. Therefore, a better balance of hole and electron currents at the emissive interface is achieved and consequently the brightness and efficiency of OLEDs are improved. - Highlights: ► Alkaline metal chlorides were used as electron injection layers in organic light-emitting diodes based on Mg:Ag cathode. ► Brightness and efficiency of OLEDs with alkaline metal chlorides as electron injection layers were all greatly enhanced. ► The Improved OLED performance was attributed to the possible interfacial chemical reaction. ► Electron-only devices are fabricated to demonstrate the electron injection enhancement.

Microwave properties of La{sub 0.8}Ag{sub 0.2}MnO{sub 3} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Rostamnejadi, Ali [Malek Ashtar University of Technology, Electroceram Research Center, Shahin Shahr, Isfahan (Iran, Islamic Republic of)

2016-11-15

In this research, single-phase nanoparticles of La{sub 0.8}Ag{sub 0.2}MnO{sub 3} with mean particle size of 15 nm have been synthesized by sol-gel method. The microwave properties of La{sub 0.8}Ag{sub 0.2}MnO{sub 3}/paraffin nanocomposite are studied by measuring the complex permittivity and permeability in the frequency range of 1-18 GHz. The composite shows both reflection and absorption electromagnetic shielding effectiveness with maximum total value of 36 dB, which is suitable for defense and microwave radiation shielding applications at high temperatures. The electromagnetic absorption properties are described in terms of dielectric relaxation processes. (orig.)

Non-Controlled Biogenic Emission of CO, H2S, NH3 and Hg0 from Lazareto's Landfill, Tenerife, Canary Islands

Science.gov (United States)

Nolasco, D.; Lima, R.; Salazar, J.; Hernández, P. A.; Pérez, N. M.

2002-12-01

Landfills are important sources of contaminant gases to the surrounding environment and a significant amount of them could be released to the atmosphere through the surface environment in a diffuse form, also known as non-controlled emission of landfill gases. CH4 and CO2 are major components in landfill gases and other gas species are only present in minor amounts. Trace compounds include both inorganic and a large number of volatile organic components. The goal of this study is to evaluate the non-controlled biogenic emission of inorganic toxic gases from Lazareto's landfill. Which is located in the city of Santa Cruz de Tenerife, with a population of about 150,000, and is used as a Palm tree park. Lazareto's landfill has an extension of 0.22 Km2 and it is not operative since 1980. A non-controlled biogenic gas emission survey of 281 sampling sites was carried out from February tod March, 2002. Surface CO2 efflux measurements were performed by means of a portable NDIR sensor according with the accumulation chamber method. Surface CO2 efflux ranged from negligible values up to 30,600 gm-2d-1. At each sampling site, surface landfill gas samples were collected at 40 cm depth using a metallic soil probe. These gas samples were analyzed within 24 hours for major and inorganic toxic gas species by means of microGC and specific electrochemical sensors. The highest concentrations of CO, H2S, NH3 and Hg0 were 3, 20, 2,227, 0.010 ppmV, respectively. Non-controlled biogenic emission rate of CO, H2S, NH3, and Hg0 were estimated by multiplying the observed surface CO2 efflux times (Inorganic Toxic Gas)i/CO2 weight ratio at each sampling site, respectively. The highest surface inorganic toxic gas efllux rates were 699 gm-2d-1 for NH3, 81, 431 and 4 mgm-2d-1 for CO, H2S and Hg0, respectively. Taking into consideration the spatial distribution of the inorganic toxic gas efflux values as well as the extension of the landfill, the non-controlled biogenic emission of CO, H2S, NH3

Transformation of Mg-bearing amorphous calcium carbonate to Mg-calcite - In situ monitoring

Science.gov (United States)

Purgstaller, Bettina; Mavromatis, Vasileios; Immenhauser, Adrian; Dietzel, Martin

2016-02-01

The formation of Mg-bearing calcite via an amorphous precursor is a poorly understood process that is of relevance for biogenic and abiogenic carbonate precipitation. In order to gain an improved insight on the controls of Mg incorporation in calcite formed via an Mg-rich amorphous calcium carbonate (Mg-ACC) precursor, the precipitation of Mg-ACC and its transformation to Mg-calcite was monitored by in situ Raman spectroscopy. The experiments were performed at 25.0 ± 0.03 °C and pH 8.3 ± 0.1 and revealed two distinct pathways of Mg-calcite formation: (i) At initial aqueous Mg/Ca molar ratios ⩽ 1:6, Mg-calcite formation occurs via direct precipitation from solution. (ii) Conversely, at higher initial Mg/Ca molar ratios, Mg-calcite forms via an intermediate Mg-rich ACC phase. In the latter case, the final product is a calcite with up to 20 mol% Mg. This Mg content is significant higher than that of the Mg-rich ACC precursor phase. Thus, a strong net uptake of Mg ions from the solution into the crystalline precipitate throughout and also subsequent to ACC transformation is postulated. Moreover, the temporal evolution of the geochemical composition of the reactive solution and the Mg-ACC has no significant effect on the obtained ;solubility product; of Mg-ACC. The enrichment of Mg in calcite throughout and subsequent to Mg-ACC transformation is likely affected by the high aqueous Mg/Ca ratio and carbonate alkalinity concentrations in the reactive solution. The experimental results have a bearing on the formation mechanism of Mg-rich calcites in marine early diagenetic environments, where high carbonate alkalinity concentrations are the rule rather than the exception, and on the insufficiently investigated inorganic component of biomineralisation pathways in many calcite secreting organisms.

Effect of second introduced phase on magnetic and magnetotransport properties of (1-x)La0.7Sr0.3Mn0.9Co0.1O3/x% Ag (x=0%, 2%, 4%) nanocomposites

Science.gov (United States)

Shah, Hiral D.; Bhalodia, J. A.

2018-05-01

The structural, magnetic and magnetotransport properties of (1-x)La0.7Sr0.3Mn0.9Co0.1O3(LSMCO)/x% Ag (x=0%, 2%, 4%) nanocomposites were investigated to explore the role of second introduced phase. (1-x) LSMCO/x% Ag (x=0%, 2%, 4%) nanocomposites are prepared via solid-state reaction method. X-ray diffraction (XRD) and SEM analysis indicated that x% of Ag are not substituted into the main LSMCO phase and remains an additive to the second phase at grain boundaries [1]. The structural parameters and the reliability factors for all the samples were successfully determined by the Rietveld refinement. Magnetization and transport properties of (1-x)LSMCO/x% Ag nanocomposites have been reported. Resistivity of the composite samples increases with Ag content in comparison with the pure LSMCO, and suppressed with applied magnetic field in all the composite samples [2]. The metal-insulator transition (TMI) and accompanied paramagnetic-ferromagnetic transition (TC) temperatures decrease with increase in Ag content. The electrical resistivity of the experimental results is explored by theoretical model below TMI. The maximum MR was observed to be 55% in the x=4% sample at 5 K temperature under 7 T magnetic field, this value is larger than that of pure LSMCO (19% at 5 K and 7 T), which is encouraging for practical application. Summarily, the addition of Ag in LSMCO improves MR% values significantly due to the more grain boundary contribution and result in better physical properties of the parent manganite system.

Speciation analysis of 129I in seawater by carrier-free AgI-AgCl coprecipitation and accelerator mass spectrometric measurement

DEFF Research Database (Denmark)

Luo, Maoyi; Hou, Xiaolin; He, Chaohui

2013-01-01

A rapid and simple method was developed for speciation analysis of 129I in seawater by selective coprecipitation of carrier-free iodide and accelerator mass spectrometry (AMS) measurement of 129I. Iodide was separated from seawater and other species of iodine by coprecipitation of AgI with Ag2SO3......, AgCl, and AgBr by addition of only 100 mg/L Ag+ and 0.3 mmol/L NaHSO3 at pH 4.2-5.5. The separation efficiency of iodide was more than 95%, and crossover between 129IO3- and 129I- fractions is less than 3%. Iodate and total inorganic iodine were converted to iodide by use of NaHSO3 at pH 1......-2 and then separated by the same method as for iodide. Ag2SO3 in the coprecipitate was removed by washing with 3 mol/L HNO3 and the excess AgCl and AgBr was removed by use of diluted NH3, and finally a 1-3 mg precipitate was obtained for AMS measurement of 129I. The recovery of iodine species in the entire procedure...

A new silver metaniobate semiconductor of Ag0.5La0.5Nb2O6 with defect-perovskite structure

Science.gov (United States)

Mi, Longqing; Feng, Yongyi; Cao, Lei; Xue, Mingqiang; Huang, Yanlin; Qin, Lin; Seo, Hyo Jin

2018-03-01

Silver-containing lanthanum metaniobate Ag0.5La0.5Nb2O6 nanoparticles were synthesized by sol-gel polymerized complex method. A typical defect-perovskite structure was confirmed by XRD Rietveld refinements. The surface characteristics of the sample were tested by SEM, TEM and EDS measurements. SEM and TEM show that the sample presents ball-like particles with the diameters of 100 nm to 400 nm. The sample shows both self-activated luminescence and photocatalytic activities. Ag0.5La0.5Nb2O6 has a direct transition with band energy of 2.85 eV. The Ag4d-O2p hybridization in the valence band contributes to the narrowed band gap. The luminescence properties of Ag0.5La0.5Nb2O6 have been investigated for the first time. The luminescence is characterized by two emission centers with maximum wavelength near 460 and 530 nm. The emission and excitation spectra, decay curves and the thermal quenching mechanism were discussed. Ag0.5La0.5Nb2O6 shows the efficient photocatalytic activities and the photodegradation rate for methylene blue dye (MB) can reach about 95% under visible light (> 420 nm) irradiation in 5 h. The trapped experiments for the active species were tested and discussed, which verified that rad OH radicals could be the major active species in photocatalysis.

Deuterium short-range order in Pd0.975Ag0.025D0.685 by diffuse neutron scattering

DEFF Research Database (Denmark)

Blaschko, O.; Klemencic, R.; Fratzl, P.

1983-01-01

By diffuse neutron scattering the D short-range order in a Pd0.975Ag0.025D0.685 crystal was investigated at 50 and 70K. The results are compared with the D ordering in the PdDx system previously investigated, and it is shown that the isointensity contours around the (1/2,1,0) point are similar...

The quinternary thiophosphate Cs0.5Ag0.5Nb2PS10

Directory of Open Access Journals (Sweden)

Sojeong Park

2010-07-01

Full Text Available The quinternary thiophosphate Cs0.5Ag0.5Nb2PS10, cesium silver tris(disulfido[tetrathiophosphato(V]diniobate(IV, has been prepared from the elements using a CsCl flux. The crystal structure is made up of ∞1[Nb2PS10] chains expanding along [010]. These chains are built up from bicapped trigonal-prismatic [Nb2S12] units and tetrahedral [PS4] groups and are linked through a linear S—Ag—S bridge, forming a two-dimensional layer. These layers then stack on top of each other, completing the three-dimensional structure with an undulating van der Waals gap. The disordered Cs+ ions reside on sites with half-occupation in the voids of this arrangement. Short [2.8843 (5 Å] and long [3.7316 (4 Å] Nb—Nb distances alternate along the chains, and anionic S22− and S2− species are observed. The charge balance of the compound can be represented by the formula [Cs+]0.5[Ag+]0.5[Nb4+]2[PS43−][S22−]3.

Removal of I by adsorption with AgX (Ag-impregnated X Zeolite) from high-radioactive seawater waste

Energy Technology Data Exchange (ETDEWEB)

Lee, Eil Hee; Lee, Keun Young; Kim, Kwang Wook; Kim, Hyung Ju; Kim, Ik Soo; Chung, Dong Yong; Moon, Jei Kwon; Choi, Jong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-09-15

This study aimed to the adsorption-removal of high- radioactive iodide (I) contained in the initially generated high-radioactive seawater waste (HSW), with the use of AgX (Ag-impregnated X zeolite). Adsorption of I by AgX (hereafter denoted as AgX-I adsorption) was increased by increasing the Ag-impregnated concentration in AgX, and its concentration was suitable at about 30 wt%. Because of AgCl precipitation by chloride ions contained in seawater waste, the leaching yields of Ag from AgX (Ag-impregnated concentration : about 30-35 wt%) was less than those in distilled water (< 1 mg/L). AgX-I adsorption was above 99% in the initial iodide concentration (Ci) of 0.01-10 mg/L at m/V (ratio of weight of adsorbent to solution volume)=2.5 g/L. This shows that efficient removal of I is possible. AgX-I adsorption was found to be more effective in distilled water than in seawater waste, and the influence of solution temperature was insignificant. Ag-I adsorption was better described by a Freundlich isotherm rather than a Langmuir isotherm. AgX-I adsorption kinetics can be expressed by a pseudo-second order rate equation. The adsorption rate constants (k2) decreased by increasing Ci, and conversely increased by increasing the ratio of m/V and the solution temperature. This time, the activation energy of AgX-I adsorption was about 6.3 kJ/mol. This suggests that AgX-I adsorption is dominated by physical adsorption with weaker bonds. The evaluation of thermodynamic parameters (a negative Gibbs free energy and a positive Enthalpy) indicates that AgX-I adsorption is a spontaneous reaction (forward reaction), and an endothermic reaction indicating that higher temperatures are favored.

File list: Oth.Emb.10.AllAg.0-4h_embryos [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Oth.Emb.10.AllAg.0-4h_embryos dm3 TFs and others Embryo 0-4h embryos SRX041388,SRX0...16153,SRX013109,SRX025484 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Oth.Emb.10.AllAg.0-4h_embryos.bed ...

File list: ALL.Emb.50.AllAg.0-6h_embryos [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available ALL.Emb.50.AllAg.0-6h_embryos dm3 All antigens Embryo 0-6h embryos SRX030958,SRX030...959 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/ALL.Emb.50.AllAg.0-6h_embryos.bed ...

High field magneto-transport study of YBa{sub 2}Cu{sub 3}O{sub 7}:Ag{sub x} (x = 0.00–0.20)

Energy Technology Data Exchange (ETDEWEB)

Rani, Poonam; Pal, Anand; Awana, V.P.S, E-mail: awana@mail.npindia.org

2014-02-15

Highlights: •YBCO: Ag{sub x} composites. •High field magneto-transport. •The upper critical field. -- Abstract: We report high field (up to 13 T) magneto transport [ρ(T)H] of YBa{sub 2}Cu{sub 3}O{sub 7} (YBCO):Ag{sub x} (x = 0.0, 0.1 and 0.2) composites. The transport properties are significantly improved by Ag doping on the insulating grain boundaries of YBCO. Pure and Ag diffused YBCO superconducting samples are synthesised through solid state reaction route. Both pure and Ag doped YBCO are superconducting at below 90 K. Though, the T{sub c} (ρ = 0) of YBCO:Ag samples under applied field of 13 T is around 65 K, the same is 45 K for pure YBCO under same applied field. The upper critical field [H{sub c2}(0)], being estimated from ρ(T)H is around 70 T for pristine sample, and is above 190 T for Ag doped samples. The boarding of the resistive transition under applied magnetic field is comparatively less and nearly single step for Ag doped samples, while the same is clearly two step and relatively much larger for the pristine YBCO. The resistive broadening is explained on the basis of changed inter-granular coupling and thermally activated flux flow (TAFF). The TAFF activation energy (U{sub 0}) is found to be linear with applied magnetic field for all the samples, but with nearly an order of magnitude less value for the Ag doped samples. Summarily, it is shown that inclusion of Ag significantly improves the superconducting performance of YBCO:Ag composites, in particular under applied field.

File list: InP.Bld.20.AllAg.M0-91 [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Bld.20.AllAg.M0-91 hg19 Input control Blood M0-91 SRX262147,SRX262153,SRX262150...,SRX262144 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Bld.20.AllAg.M0-91.bed ...

File list: InP.Bld.10.AllAg.M0-91 [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Bld.10.AllAg.M0-91 hg19 Input control Blood M0-91 SRX262150,SRX262147,SRX262153...,SRX262144 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Bld.10.AllAg.M0-91.bed ...

File list: InP.Bld.05.AllAg.M0-91 [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.Bld.05.AllAg.M0-91 hg19 Input control Blood M0-91 SRX262150,SRX262153,SRX262144...,SRX262147 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Bld.05.AllAg.M0-91.bed ...

File list: Oth.Emb.05.AllAg.0-2h_embryos [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Oth.Emb.05.AllAg.0-2h_embryos dm3 TFs and others Embryo 0-2h embryos SRX150049,SRX1...50050 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Oth.Emb.05.AllAg.0-2h_embryos.bed ...

Temperature behaviour of optical parameters in (Ag3AsS3)0.3(As2S3)0.7 thin films

Science.gov (United States)

Kutsyk, Mykhailo M.; Ráti, Yosyp Y.; Izai, Vitalii Y.; Makauz, Ivan I.; Studenyak, Ihor P.; Kökényesi, Sandor; Komada, Paweł; Zhailaubayev, Yerkin; Smailov, Nurzhigit

2015-12-01

(Ag3AsS3)0.3(As2S3)0.7 thin films were deposited onto a quartz substrate by rapid thermal evaporation. The optical transmission spectra of thin films were measured in the temperature range 77-300 K. It is shown that the absorption edge spectra are described by the Urbach rule. The temperature behaviour of absorption spectra was studied, the temperature dependences of energy position of absorption edge and Urbach energy were investigated. The influence of transition from three-dimensional glass to the two-dimensional thin film as well as influence of Ag3AsS3 introduction into As2S3 on the optical parameters of (Ag3AsS3)0.3(As2S3)0.7 were analysed. The spectral and temperature behaviour or refractive index for (Ag3AsS3)0.3(As2S3)0.7 thin film were studied.

Using Ag/Ag2O/SnO2 Nanocomposites to Remove Malachite Green by a Photocatalytic Process

Science.gov (United States)

Taufik, A.; Paramarta, V.; Prakoso, S. P.; Saleh, R.

2017-03-01

Silver/silver oxide/tin oxide nanocomposites of various weight ratios were synthesized using a microwave-assisted method. The Ag/Ag2O:SnO2 nanoparticle weight ratios used were 25:75, 50:50, and 75:25. All samples were characterized using X-ray diffraction, UV-Vis spectroscopy, Differential Scanning Calorimetry and Thermogravimetric Analysis (TGA). The Ag/Ag2O/SnO2 nanocomposites contained cubic structures provided by the Ag and Ag2O and tetragonal structures provided by the SnO2. The silver resulted in surface plasmon resonance (SPR) at a wavelength of about 435 nm. The silver oxide material was transformed into pure Ag at a temperature of about 370 °C The photocatalytic activity was tested on the degradation of malachite green (MG) from an aqueous solution. The results showed that Ag/Ag2O/SnO2 at a ratio of 50:50 exhibited the best photocatalytic performance for degrading MG under visible-light irradiation. The degradation of MG using Ag/Ag2O/SnO2 nanocomposites followed pseudo first-order kinetic reactions, and electron holes were found to be the main species acting on the degradation process.

File list: Oth.Emb.50.AllAg.0-24h_embryos [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Oth.Emb.50.AllAg.0-24h_embryos dm3 TFs and others Embryo 0-24h embryos SRX050598,SR...X050601,SRX050600,SRX050599 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Oth.Emb.50.AllAg.0-24h_embryos.bed ...

File list: Oth.Emb.05.AllAg.0-24h_embryos [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Oth.Emb.05.AllAg.0-24h_embryos dm3 TFs and others Embryo 0-24h embryos SRX050599,SR...X050598,SRX050601,SRX050600 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Oth.Emb.05.AllAg.0-24h_embryos.bed ...

Preparation and electrochemical properties of La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 (x = 0, 0.30, 0.33, 0.36, 0.39) hydrogen storage alloys

International Nuclear Information System (INIS)

Tian, Xiao; Wei, Wei; Duan, Ruxia; Zheng, Xinyao; Zhang, Huaiwei; Tegus, O.; Li, Xingguo

2016-01-01

The as-cast alloy with the composition of La_0_._7_0Ni_2_._4_5Co_0_._7_5Al_0_._3_0 was prepared by vacuum arc melting. La–Mg–Ni-based La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 hydrogen storage alloy has been synthesized by high-energy vibratory milling blending of the La_0_._7_0Ni_2_._4_5Co_0_._7_5Al_0_._3_0 as-cast alloy and elemental Mg, followed by an isothermal annealing. The microstructures and electrochemical properties of the La_0_._7_0Ni_2_._4_5Co_0_._7_5Al_0_._3_0 and La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloys were investigated by XRD, SEM and electrochemical measurements. The XRD analysis and Rietveld refinement showed that the as-cast La_0_._7_0Ni_2_._4_5Co_0_._7_5Al_0_._3_0 alloy consists of single LaNi_5 phase, whereas the La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloys contain the LaNi_5 and (La, Mg)_2Ni_7. The electrochemical measurements indicated that the maximum discharge capacity and discharge potential characteristic of the La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloys increases first and then decreases with increasing x. The maximum discharge capacity and discharge potential characteristic of alloy reaches the optimum when x is 0.36. The cyclic stability of the La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloy with a smaller quantity of Mg is better than that of the alloy with a larger quantity of Mg. - Highlights: • La–Mg–Ni-based alloy was synthesized by melting, milling and subsequent annealing. • Mg atoms exist in the La_2Ni_7 phase prior to LaNi_5 phase. • The La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloys consist of the LaNi_5 and (La, Mg)_2Ni_7. • The more Mg element the alloys contain, the easier aggregation Mg atom is. • The C_m_a_x of La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloy first increases and then decreases with rising x.

Phase structure and electrochemical properties of La0.67Mg0.33Ni3.0-xCox (x=0.0, 0.25, 0.5, 0.75) hydrogen storage alloys

International Nuclear Information System (INIS)

Wang Dahui; Luo Yongchun; Yan Ruxu; Zhang Faliang; Kang Long

2006-01-01

La 0.67 Mg 0.33 Ni 3.0-x Co x (x=0.0, 0.25, 0.50, 0.75) hydrogen storage alloys were prepared by induction melting. Influences of partial substitution of Co for Ni on phase structure and electrochemical properties of La 0.67 Mg 0.33 Ni 3.0 were investigated by means of X-ray diffraction (XRD), electron probe X-ray microanalysis (EPMA) and electrochemical measurements. XRD patterns and back scattered electron images show that the alloys were composed of the (La,Mg)Ni 3 phase with the PuNi 3 -type structure and the (La,Mg) 2 Ni 7 phase with the Ce 2 Ni 7 -type structure. The lattice parameters a, c and the unit-cell volumes v vary with the increase of Co content x. The electrochemical measurements show that partial Co substitution for Ni had no influence on the initial activation rate of the alloys. The maximum electrochemical discharge capacity increases firstly then decreases, the high-rate dischargeabilities (HRDs) of La 0.67 Mg 0.33 Ni 3.0-x Co x alloy electrodes increase with the increase of Co content. Moreover, the cycle stabilities of La 0.67 Mg 0.33 Ni 3.0-x Co x is not improved by small quantity replacement Ni by Co except for x=0.75

File list: ALL.Emb.50.AllAg.0-4h_embryos [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available ALL.Emb.50.AllAg.0-4h_embryos dm3 All antigens Embryo 0-4h embryos SRX013030,SRX013...RX013103,SRX025484,SRX013031,SRX1426951,SRX013094 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/ALL.Emb.50.AllAg.0-4h_embryos.bed ...

Effects of Cu or Ag additions on the kinetics of MgB₂ phase formation in Fe-sheated wires

DEFF Research Database (Denmark)

Grivel, Jean-Claude; Abrahamsen, Asger Bech; Bednarcik, J.

2008-01-01

MgB2/Fe wires have been produced by the powder-in-tube technique following the in situ route. The influence of low amounts of Cu or Ag additions into the precursor powder mixture on the kinetics of MgB2 formation was studied in situ by means of synchrotron x-ray diffraction during heat-treatments...

Small angle, quasielastic and inelastic neutron scattering from 0.85AgPO3-0.15PbI2 glass

International Nuclear Information System (INIS)

Malugani, J.P.; Tachez, M.; Mercier, R.

1987-01-01

A small angle neutron scattering (SANS) experiment and a quasielastic neutron scattering (QENS) experiment were performed on the fast ionic conductor 0.85AgPO 3 -0.15PbI 2 , which is a vitreous electrolyte. The SANS data show that the scattering obeys Guinier's law for Q -2 A; dispersed heterogeneities are present in the glass with a mean radius of gyration of 20 A. The QENS spectra show a quasielastic broadening of the elastic peak and a long tail up to 40 meV which is due to an inelastic distribution. The results seem to confirm the hypothesis on the structure of this glass: small 'clusters' of AgI with tetrahedral coordination are dispersed in the AgPO 3 host glass. In order to build these clusters, an exchange between Ag + and Pb 2+ is proposed. 18 refs.; 6 figs.; 2 tabs

File list: His.Emb.20.AllAg.0-4h_embryos [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available His.Emb.20.AllAg.0-4h_embryos dm3 Histone Embryo 0-4h embryos SRX013030,SRX013003,S...RX013029,SRX013103,SRX1426953,SRX1426951,SRX013031,SRX013094 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/His.Emb.20.AllAg.0-4h_embryos.bed ...

Chondrogenic differentiation of ATDC5-cells under the influence of Mg and Mg alloy degradation

Energy Technology Data Exchange (ETDEWEB)

Martinez Sanchez, Adela H., E-mail: adela.martinez@hzg.de [Helmholtz-Zentrum Geesthacht, Institute of Material Research, Department for Structural Research on Macromolecules, Geesthacht (Germany); Feyerabend, Frank; Laipple, Daniel; Willumeit-Römer, Regine [Helmholtz-Zentrum Geesthacht, Institute of Material Research, Department for Structural Research on Macromolecules, Geesthacht (Germany); Weinberg, Annelie [Department of Orthopedics and Orthopedic Surgery, Medical University of Graz (Austria); Luthringer, Bérengère J.C. [Helmholtz-Zentrum Geesthacht, Institute of Material Research, Department for Structural Research on Macromolecules, Geesthacht (Germany)

2017-03-01

Biodegradable magnesium (Mg)-based materials are a potential alternative to permanent implants for application in children. Nevertheless effects of those materials on growth plate cartilage and chondrogenesis have not been previously evaluated. In vitro differentiation of ATDC5 cells was evaluated under the influence of pure Mg (PMg), Mg with 10 wt% of gadolinium (Mg-10Gd) and Mg with 2 wt% of silver (Mg-2Ag) degradation products (extracts) and direct cell culture on the materials. Gene expression showed an inhibitory effect on ATDC5 mineralization with the three extracts and a chondrogenic potential of Mg-10Gd. Cells cultured in Mg-10Gd and Mg-2Ag extracts showed the same proliferation and morphology than cells cultured in growth conditions. Mg-10Gd induced an increase in production of ECM and a bigger cell size, similar to the effects found with differentiation conditions. An increased metabolic activity was observed in cells cultured under the influence of Mg-10Gd extracts, indicated by an acidic pH during most of the culture period. After 7 days of culture on the materials, ATDC5 growth, distribution and ECM synthesis were higher on Mg-10Gd samples, followed by Mg-2Ag and PMg, which was influenced by the homogeneity and composition of the degradation layer. This study confirmed the tolerance of ATDC5 cells to Mg-based materials and a chondrogenic effect of Mg-10Gd. Further studies in vitro and in vivo are necessary to evaluate cell reactions to those materials, as well as the effects on bone growth and the biocompatibility of the alloying system in the body. - Highlights: • Degradation of PMg, and Mg-2Ag do not influence ATDC5 cells growth and chondrogenic redifferentiation. • Mg-10Gd enhances fast chondrogenic redifferentiation and expression of hyperthrophic markers on ATDC5 cells. • Further evaluation of the effects of PMg, Mg-10Gd and Mg-2Ag in vivo are necessary to confirm its potential for application in growing bones.

Chondrogenic differentiation of ATDC5-cells under the influence of Mg and Mg alloy degradation

International Nuclear Information System (INIS)

Martinez Sanchez, Adela H.; Feyerabend, Frank; Laipple, Daniel; Willumeit-Römer, Regine; Weinberg, Annelie; Luthringer, Bérengère J.C.

2017-01-01

Biodegradable magnesium (Mg)-based materials are a potential alternative to permanent implants for application in children. Nevertheless effects of those materials on growth plate cartilage and chondrogenesis have not been previously evaluated. In vitro differentiation of ATDC5 cells was evaluated under the influence of pure Mg (PMg), Mg with 10 wt% of gadolinium (Mg-10Gd) and Mg with 2 wt% of silver (Mg-2Ag) degradation products (extracts) and direct cell culture on the materials. Gene expression showed an inhibitory effect on ATDC5 mineralization with the three extracts and a chondrogenic potential of Mg-10Gd. Cells cultured in Mg-10Gd and Mg-2Ag extracts showed the same proliferation and morphology than cells cultured in growth conditions. Mg-10Gd induced an increase in production of ECM and a bigger cell size, similar to the effects found with differentiation conditions. An increased metabolic activity was observed in cells cultured under the influence of Mg-10Gd extracts, indicated by an acidic pH during most of the culture period. After 7 days of culture on the materials, ATDC5 growth, distribution and ECM synthesis were higher on Mg-10Gd samples, followed by Mg-2Ag and PMg, which was influenced by the homogeneity and composition of the degradation layer. This study confirmed the tolerance of ATDC5 cells to Mg-based materials and a chondrogenic effect of Mg-10Gd. Further studies in vitro and in vivo are necessary to evaluate cell reactions to those materials, as well as the effects on bone growth and the biocompatibility of the alloying system in the body. - Highlights: • Degradation of PMg, and Mg-2Ag do not influence ATDC5 cells growth and chondrogenic redifferentiation. • Mg-10Gd enhances fast chondrogenic redifferentiation and expression of hyperthrophic markers on ATDC5 cells. • Further evaluation of the effects of PMg, Mg-10Gd and Mg-2Ag in vivo are necessary to confirm its potential for application in growing bones.

Ethylbenzene dehydrogenation over Mg3Fe0.5−xCoxAl0.5 catalysts derived from hydrotalcites: Comparison with Mg3Fe0.5−yNiyAl0.5 catalysts

KAUST Repository

Atanda, Luqman A.; Balasamy, Rabindran J.; Khurshid, Alam; Al-Ali, Ali A S; Sagata, Kunimasa; Asamoto, Makiko; Yahiro, Hidenori; Nomura, Kiyoshi; Sano, Tsuneji; Takehira, Katsuomi; Al-Khattaf, Sulaiman S.

2011-01-01

A series of Mg3Fe0.5-xCoxAl0.5 (x = 0-0.5) catalysts were prepared from hydrotalcite precursors and their activities in the dehydrogenation of ethylbenzene were compared with those of a series of Mg3Fe0.5-yNiyAl0.5 (y = 0-0.5) catalysts also derived

Influence of defects on the adhesion of transition metals on non-polar MgO(001) surface: comparative theoretical analysis

International Nuclear Information System (INIS)

Zhukovskii, Yu.F.; Kotomin, E.A.

2004-01-01

Full text: First principles simulations were performed for noble (Ag) and transition (Cu) atoms adsorbed on regular and defective MgO(001) substrate [1]. Both metal atoms and surface O vacancies (F s centers) were distributed uniformly with one Ag (Cu) atom or F 2 defect per 2x2 surface supercell. Surface O 2- ions are the energetically more preferable for metal atom adsorption on a regular substrate as compared to Mg 2+ ions. The nature of the interaction between Ag or Cu adatoms and a defectless MgO substrate is physisorption (despite the difference in the adsorption energies: 0.62 eV vs. 0.39 eV per Cu and Ag adatom, respectively). Above the F s centers, metal atoms are bounded much stronger as compared with the regular O 2- sites (2.4 eV vs. 2.1 eV per Cu and Ag adatoms, respectively). This is accompanied by a substantial charge transfer towards each adatom (Δq Cu = 0.41 e and Δq Ag = 0.32 e) as well as a formation of partly covalent Me-F s bonds across the interface (Mulliken bond populations p Cu-F s = 0.25 e and p Ag-F s = 0.33 e). Thus, adsorption of transition metal atom on the defective MgO(001) substrate clearly indicates a strong electrostatic bonding because of the considerable interfacial charge redistribution. [1] Yu.F. Zhukovskii, E.A. Kotomin, and G. Borstel, Adsorption of single Ag and Cu atoms on regular and defective MgO(001) substrates: an ab initio study - Vacuum, 73 (2004) in press

Positron annihilation 2D-ACAR study of semi-coherent Li nanoclusters in MgO(1 0 0) and MgO(1 1 0)

International Nuclear Information System (INIS)

Falub, C.V.; Mijnarends, P.E.; Eijt, S.W.H.; Huis, M.A. van; Veen, A. van; Schut, H.

2002-01-01

Depth selective positron annihilation two-dimensional angular correlation of annihilation radiation (2D-ACAR) is used to determine the electronic structure of Li nanoclusters formed by implantation of 10 16 cm -2 6 Li ions (with an energy of 30 keV) in MgO(1 0 0) and (1 1 0) crystals, and subsequently annealed at 950 K. The 2D-ACAR spectra of Li-implanted MgO obtained with 4 keV positrons reveal the semi-coherent ordering state of the embedded metallic Li nanoclusters. The results agree with ab initio Korringa-Kohn-Rostoker calculations

Positron annihilation 2D-ACAR study of semi-coherent Li nanoclusters in MgO(1 0 0) and MgO(1 1 0)

Energy Technology Data Exchange (ETDEWEB)

Falub, C.V. E-mail: c.falub@iri.tudelft.nl; Mijnarends, P.E.; Eijt, S.W.H.; Huis, M.A. van; Veen, A. van; Schut, H

2002-05-01

Depth selective positron annihilation two-dimensional angular correlation of annihilation radiation (2D-ACAR) is used to determine the electronic structure of Li nanoclusters formed by implantation of 10{sup 16} cm{sup -2} {sup 6}Li ions (with an energy of 30 keV) in MgO(1 0 0) and (1 1 0) crystals, and subsequently annealed at 950 K. The 2D-ACAR spectra of Li-implanted MgO obtained with 4 keV positrons reveal the semi-coherent ordering state of the embedded metallic Li nanoclusters. The results agree with ab initio Korringa-Kohn-Rostoker calculations.

Positron annihilation 2D-ACAR study of semi-coherent Li nanoclusters in MgO( 1 0 0 ) and MgO( 1 1 0 )

Science.gov (United States)

Falub, C. V.; Mijnarends, P. E.; Eijt, S. W. H.; van Huis, M. A.; van Veen, A.; Schut, H.

2002-05-01

Depth selective positron annihilation two-dimensional angular correlation of annihilation radiation (2D-ACAR) is used to determine the electronic structure of Li nanoclusters formed by implantation of 10 16 cm -26Li ions (with an energy of 30 keV) in MgO(1 0 0) and (1 1 0) crystals, and subsequently annealed at 950 K. The 2D-ACAR spectra of Li-implanted MgO obtained with 4 keV positrons reveal the semi-coherent ordering state of the embedded metallic Li nanoclusters. The results agree with ab initio Korringa-Kohn-Rostoker calculations.

A new reversible Mg3Ag–H2 system for hydrogen storage

International Nuclear Information System (INIS)

Si, T.Z.; Zhang, J.B.; Liu, D.M.; Zhang, Q.A.

2013-01-01

Highlights: •Mg 3 Ag compound with high-purity was prepared by hydrogen metallurgy. •Mg 3 Ag is first employed for reversible hydrogen storage with altered thermodynamics. •The enhanced cyclic stability is due to the prevention of MgH 2 sintering by MgAg. -- Abstract: For the first time, the compound Mg 3 Ag was employed as a medium for hydrogen storage. It has been demonstrated that the hydriding/dehydriding process of Mg 3 Ag is reversible through the reaction Mg 3 Ag + 2H 2 ↔ 2MgH 2 + MgAg with obtaining altered thermodynamics. An enhanced cycling stability is also achieved by the capacity retention of 95% after 30 cycles, much higher than 70% for the pure Mg sample, which can be explained that the agglomeration and sintering of the resulting MgH 2 are efficiently prevented by the formation of hard and brittle MgAg phase upon multi-cycling

High activity of Ag-doped Cd0.1Zn0.9S photocatalyst prepared by the hydrothermal method for hydrogen production under visible-light irradiation

Directory of Open Access Journals (Sweden)

Leny Yuliati

2014-05-01

Full Text Available Background: The hydrothermal method was used as a new approach to prepare a series of Ag-doped Cd0.1Zn0.9S photocatalysts. The effect of Ag doping on the properties and photocatalytic activity of Cd0.1Zn0.9S was studied for the hydrogen production from water reduction under visible light irradiation.Results: Compared to the series prepared by the co-precipitation method, samples prepared by the hydrothermal method performed with a better photocatalytic activity. The sample with the optimum amount of Ag doping showed the highest hydrogen production rate of 3.91 mmol/h, which was 1.7 times higher than that of undoped Cd0.1Zn0.9S. With the Ag doping, a red shift in the optical response was observed, leading to a larger portion of the visible light absorption than that of without doping. In addition to the larger absorption in the visible-light region, the increase in photocatalytic activity of samples with Ag doping may also come from the Ag species facilitating electron–hole separation.Conclusion: This study demonstrated that Ag doping is a promising way to enhance the activity of Cd0.1Zn0.9S photocatalyst.

Study of the tungsten bronze Ag0.01WO3 using positron annihilation method

International Nuclear Information System (INIS)

Dryzek, J.; Dryzek, E.; Placzek, A.

1992-01-01

The study of the positron annihilation and the Seebeck effect was performed on silver doped tungsten trioxide of composition Ag 0.01 WO 3 and the tungsten trioxide phase: WO 2.90 (W 20 O 58 ). Both methods point out that there are some clusters of Ag + ions in the first compound and oxygen vacancies in the second case. The clusters have some internal substructure. The measurements of the Seebeck effect showed that Ag 0.01 WO 3 is normal n-type semiconductor whereas WO 2.90 exhibits metal-like properties

Thermal expansion properties of Bi-2212 in Ag or an Ag-alloy matrix

International Nuclear Information System (INIS)

Tenbrink, J.; Krauth, H.

1994-01-01

The thermal expansion properties of polycrystalline Bi 2 Sr 2 Ca 1 Cu 2 O 8+x melt-processed bulk specimens, and Bi 2 Sr 2 Ca 1 Cu 2 O 8+x monocore as well as multifilamentary round wires in Ag or Ag-alloy matrix have been investigated over the temperature range from -150 to 800 degrees C. Although the thermal expansion of Bi 2 Sr 2 Ca 1 Cu 2 O 8+x is distinctly lower compared with Ag, the thermal expansion properties of the Bi 2 Sr 2 Ca 1 Cu 2 O 8+x -Ag or AgNiMg-alloy composite conductors are essentially governed by the matrix material. The thermal expansion of the encountered oxide-dispersion-strengthened AgNiMg alloys is only slightly lower compared with that of pure Ag. Therefore the thermal expansion of all investigated Bi 2 Sr 2 Ca 1 Cu 2 O 8+x -Ag or Ag-alloy composite wires was found to be close to that of pure Ag. The reason for this striking behaviour is shown to be related to a surprisingly low elastic modulus of the polycrystalline Bi-2212 wire cores of the order of 10 to a maximum 40 GPa. (author)

Evaluation of the microstructure of Al-Cu-Li-Ag-Mg Weldalite (tm) alloys, part 4

Science.gov (United States)

Pickens, Joseph R.; Kumar, K. S.; Brown, S. A.; Gayle, Frank W.

1991-01-01

Weldalite (trademark) 049 is an Al-Cu-Li-Ag-Mg alloy designed to have ultrahigh strength and to serve in aerospace applications. The alloy displays significantly higher strength than competitive alloys in both naturally aged and artificially aged tempers. The strengthening phases in such tempers have been identified to, in part, explain the mechanical properties attained. In general, the alloy is strengthened by delta prime Al3Li and Guinier-Preston (GP) zones in the naturally aged tempers. In artificially aged tempers in slightly underaged conditions, strengthening is provided by several phases including GP zones, theta prime Al2Cu, S prime Al2CuMg, T(sub 1) Al2CuLi, and possibly a new phase. In the peak strength artificially aged tempers, T(sub 1) is the predominant strengthening phase.

Effects of packaging, mineral oil coating, and storage time on biogenic amine levels and internal quality of eggs.

Science.gov (United States)

Figueiredo, T C; Assis, D C S; Menezes, L D M; Oliveira, D D; Lima, A L; Souza, M R; Heneine, L G D; Cançado, S V

2014-12-01

This study was carried out with the aim of evaluating the effects of mineral oil application on eggshells and the use of plastic packages with lids on the physical-chemical and microbiological quality and biogenic amine contents of eggs stored under refrigeration for up to 125 d. A total of 1,920 eggs from 46-wk-old Hyline W36 laying hens were randomly distributed into 4 groups soon after classification: (i) 480 eggs were stored in pulp carton tray packages; (ii) 480 eggs were stored in plastic packages with lids; (iii) 480 eggs were stored in carton packages after the application of mineral oil; and (iv) 480 eggs were stored in plastic packages with lids after the application of mineral oil. The internal quality was measured by Haugh units, by the counts of mesophilic and psychrotrophic microorganisms, by the most probable number of total and thermal-tolerant coliforms, by the counts of molds and yeasts, by the analysis of Salmonella spp. and Staphylococcus spp., and by the levels of biogenic amines in the egg yolk and albumen. The application of mineral oil to the eggshell resulted in higher Haugh unit values throughout storage, and the use of plastic packages altered the internal quality. The application of mineral oil and the use of packaging had no effects on the microbiological and biogenic amine results. Microbiological analyses showed the absence of Salmonella spp., Staphylococcus aureus, thermal-tolerant coliforms, and fungi. However, the highest counts of mesophilic (1.1 × 10(7) cfu/g) and psychrotrophic (6.7 × 10(7) cfu/g) microorganisms were recorded. The highest values of biogenic amines detected and quantified were putrescine (2.38 mg/kg) and cadaverine (7.27 mg/kg) in the egg yolk and putrescine (1.95 mg/kg), cadaverine (2.83 mg/kg), and phenylethylamine (2.57 mg/kg) in the albumen. Despite these results, the biogenic amine levels recorded were considered low and would not be harmful to consumer health. ©2014 Poultry Science Association Inc.

First-principles study of hydrogen dissociation and diffusion on transition metal-doped Mg(0 0 0 1) surfaces

International Nuclear Information System (INIS)

Wang, Zhiwen; Guo, Xinjun; Wu, Mingyi; Sun, Qiang; Jia, Yu

2014-01-01

First-principles calculations within the density functional theory (DFT) have been carried out to study hydrogen molecules dissociation and diffusion on clean and transition metals (TMs) doped Mg(0 0 0 1) surfaces following Pozzo et al. work. Firstly, the stability of Mg(0 0 0 1) surface doped with transition metals atom has been studied. The results showed that transition metals on the left of the table tend to substitute Mg in the second layer, while the other transition metals prefer to substitute Mg in the first layer. Secondly, we studied hydrogen molecules dissociation and diffusion on clean and Mg(0 0 0 1) surfaces which the transition metal atoms substituted both in the first layer and second layer. When transition metal atoms substitute in the first layer, the results agree with the Pozzo et al. result; when transition metal atoms substitute in the second layer, the results showed that the transition metals on the left of the periodic table impact on the dissociation barriers is less. However, for the transition metals (Mn, Fe, Co, Ni) on the right, there is a great impact on the barriers. The transition metals doped surfaces bind the dissociated H atoms loosely, making them easily diffused. The results further reveal that the Fe dopant on the Mg surface is the best choice for H 2 dissociation and hydrogen storage.

Biochar alleviates the toxicity of imidacloprid and silver nanoparticles (AgNPs) to Enchytraeus albidus (Oligochaeta).

Science.gov (United States)

Nyoka, Ngitheni Winnie-Kate; Kanyile, Sthandiwe Nomthandazo; Bredenhand, Emile; Prinsloo, Godfried Jacob; Voua Otomo, Patricks

2018-04-01

The present study investigated the use of biochar for the alleviation of the toxic effects of a nanosilver colloidal dispersion and a chloronicotinyl insecticide. The survival and reproduction of the potworm Enchytraeus albidus were assessed after exposure to imidacloprid and silver nanoparticles (AgNPs). E. albidus was exposed to 0, 25, 50, 100, 200, and 400 mg imidacloprid/kg and 0, 5, 25, 125, and 625 mg Ag/kg for 21 days in 10% biochar amended and non-biochar amended OECD artificial soil. In both exposure substrates, the effects of imidacloprid on survival were significant in the two highest treatments (p imidacloprid. In the case of AgNPs, significant mortality was only observed in the highest AgNP treatments in both the amended and non-amended soils (p imidacloprid/kg in the non-amended soil and a higher EC 50  = 46.23 mg imidacloprid/kg in the biochar-amended soil. This indicated a 2-fold decrease in imidacloprid toxicity due to biochar amendment. A similar observation was made in the case of AgNPs where a reproduction EC 50  = 166.70 mg Ag/kg soil in the non-amended soil increased to an EC 50  > 625 mg Ag/kg soil (the highest AgNP treatment) in the amended soil. This indicated at least a 3.7-fold decrease in AgNPs toxicity due to biochar amendment. Although more studies may be needed to optimize the easing effects of biochar on the toxicity of these chemicals, the present results show that biochar could be useful for the alleviation of the toxic effects of imidacloprid and silver nanoparticles in the soil.

First-principles study of Mg incorporation at wurtzite InN (0 0 0 1) and (0001-bar) surfaces

International Nuclear Information System (INIS)

Ding, S.F.; Qu, X.P.; Fan, G.H.

2009-01-01

In this article we investigate the energetics of Mg adsorption and incorporation at the InN(0 0 0 1) and InN(0001-bar) surfaces by the method of total energy plane-wave expansions with ultra-soft pseudo potential technology based on the density functional theory (DFT) in the generalized approximation (GGA). It is found that for a 1/4 monolayer (ML) coverage of the InN(0 0 0 1) surface, Mg atoms preferentially adsorb at the bridge sites and T4 sites, but they are unstable when compared with Mg incorporated in the first three layers. For a 1/4 ML coverage of the InN(0001-bar) surface, Mg atoms preferentially adsorb at the H3 sites with the formation energy of -3.49 (eV/(2x2) supercell), which is lower than that of the T4 sites, and the formation energy increases with increasing magnesium coverage. Further study shows that the formation energy for Mg atom is lower than that of In atom, which indicates that magnesium adsorption is more favorable in these conditions.

Soldering Characteristics and Mechanical Properties of Sn-1.0Ag-0.5Cu Solder with Minor Aluminum Addition

Directory of Open Access Journals (Sweden)

Yee Mei Leong

2016-06-01

Full Text Available Driven by the trends towards miniaturization in lead free electronic products, researchers are putting immense efforts to improve the properties and reliabilities of Sn based solders. Recently, much interest has been shown on low silver (Ag content solder SAC105 (Sn-1.0Ag-0.5Cu because of economic reasons and improvement of impact resistance as compared to SAC305 (Sn-3.0Ag-0.5Cu. The present work investigates the effect of minor aluminum (Al addition (0.1–0.5 wt.% to SAC105 on the interfacial structure between solder and copper substrate during reflow. The addition of minor Al promoted formation of small, equiaxed Cu-Al particle, which are identified as Cu3Al2. Cu3Al2 resided at the near surface/edges of the solder and exhibited higher hardness and modulus. Results show that the minor addition of Al does not alter the morphology of the interfacial intermetallic compounds, but they substantially suppress the growth of the interfacial Cu6Sn5 intermetallic compound (IMC after reflow. During isothermal aging, minor alloying Al has reduced the thickness of interfacial Cu6Sn5 IMC but has no significant effect on the thickness of Cu3Sn. It is suggested that of atoms of Al exert their influence by hindering the flow of reacting species at the interface.

Soldering Characteristics and Mechanical Properties of Sn-1.0Ag-0.5Cu Solder with Minor Aluminum Addition

Science.gov (United States)

Leong, Yee Mei; Haseeb, A.S.M.A.

2016-01-01

Driven by the trends towards miniaturization in lead free electronic products, researchers are putting immense efforts to improve the properties and reliabilities of Sn based solders. Recently, much interest has been shown on low silver (Ag) content solder SAC105 (Sn-1.0Ag-0.5Cu) because of economic reasons and improvement of impact resistance as compared to SAC305 (Sn-3.0Ag-0.5Cu. The present work investigates the effect of minor aluminum (Al) addition (0.1–0.5 wt.%) to SAC105 on the interfacial structure between solder and copper substrate during reflow. The addition of minor Al promoted formation of small, equiaxed Cu-Al particle, which are identified as Cu3Al2. Cu3Al2 resided at the near surface/edges of the solder and exhibited higher hardness and modulus. Results show that the minor addition of Al does not alter the morphology of the interfacial intermetallic compounds, but they substantially suppress the growth of the interfacial Cu6Sn5 intermetallic compound (IMC) after reflow. During isothermal aging, minor alloying Al has reduced the thickness of interfacial Cu6Sn5 IMC but has no significant effect on the thickness of Cu3Sn. It is suggested that of atoms of Al exert their influence by hindering the flow of reacting species at the interface. PMID:28773645

Electrical conductivity of cobalt doped La 0.8Sr 0.2Ga 0.8Mg 0.2O 3- δ

Science.gov (United States)

Wang, Shizhong; Wu, Lingli; Liang, Ying

La 0.8Sr 0.2Ga 0.8Mg 0.2O 3- δ (LSGM8282), La 0.8Sr 0.2Ga 0.8Mg 0.15Co 0.05O 3- δ (LSGMC5) and La 0.8Sr 0.2Ga 0.8Mg 0.115Co 0.085O 3- δ (LSGMC8.5) were prepared using a conventional solid-state reaction. Electrical conductivities and electronic conductivities of the samples were measured using four-probe impedance spectrometry, four-probe dc polarization and Hebb-Wagner polarization within the temperature range of 973-1173 K. The electrical conductivities in LSGMC5 and LSGMC8.5 increased with decreasing oxygen partial pressures especially in the high (>10 -5 atm) and low oxygen partial pressure regions (lanthanum gallate samples increased with increasing concentration of cobalt, suggesting that the concentration of cobalt should be optimized carefully to maintain a high electrical conductivity and close to 1 oxygen ion transference number.

柱前衍生HPLC同时测定鱼中多种生物胺及其变化规律%Biogenic Amines in Fish Determined by HPLC with Pre-column Dansylation

Institute of Scientific and Technical Information of China (English)

胡月; 黄志勇

2012-01-01

目的:采用高效液相色谱法同时测定鱼中7种生物胺(即色胺、腐胺、尸胺、组胺、酪胺、亚精胺和精胺)的含量,研究在不同贮藏条件下鱼体生物胺的变化规律.方法:样品用5％三-氯乙酸溶液提取后,用丹磺酰氯进行柱前衍生,经C18色谱柱(4.6 mm I.D.×150 mm)分离,用水和乙腈进行梯度洗脱,于波长254 nm处检测.考察大黄鱼和黄鲷在-20、4和25℃贮藏不同时间时生物胺的变化情况.结果:20 min内7种生物胺得到良好的分离,在0.1～20.0 mg/kg范围具有良好的线性关系(r＞0.999).生物胺的平均回收率73％～101％,RSD 5.9％～20.1％.所测的7种新鲜海鱼中,除金线鱼具有较高的生物胺含量(170.8 mg/kg)外,其它鱼的生物胺含量很低(3.95～23.63mg/kg).在-20℃条件下大黄鱼和黄鲷中生物胺的总量无显著变化(p＜0.05),而在4℃和25℃时,鱼体中的生物胺总量随贮藏时间的延长而增加.其中腐胺、尸胺、组胺和酪胺含量变化敏锐,随着贮藏时间的延长和温度的上升,其含量显著增加(p＜0.05).结论:低温贮藏可有效控制鱼体中生物胺的形成.腐胺、尸胺、组胺和酪胺可作为判断鱼体新鲜度的质量指标.%Objective: Seven biogenic amines (including tryptaraine, putrescine, cadaverine, hisamine, tyramine, spermidine and spermine) in fish were simultaneously determined by high-performance liquid chromatograph (HPLC), and the changes of biogenic amines of fish stored at different conditions were investigated. Method: After being extracted with 5% TCA from the aquatic products, the biogenic amines were derived by dansyl chloride before the separation with a C18 column (4.6 mm I.D. xl50 mm). The biogenic amines were eluted using a mixture of water and acetonitrile at a gradient elution program, and were detected at 254 nm. The changes of biogenic amines in the two species of Pseudosci-aena crocea and Dentex tumifrons separately stored at -20 ℃, 4 �

Phase, microstructure and microwave dielectric properties of Mg0:95Ni0:05Ti0:98Zr0:02O3 ceramics

Directory of Open Access Journals (Sweden)

Manan Abdul

2015-03-01

Full Text Available Mg0:95Ni0:05Ti0:98Zr0:02O3 ceramics was prepared via conventional solid-state mixed-oxide route. The phase, microstructure and microwave dielectric properties of the sintered samples were characterized using X-ray diffraction (XRD, scanning electron microscopy (SEM and a vector network analyzer. The microstructure comprised of circular and elongated plate-like grains. The semi quantitative analysis (EDS of the circular and elongated grains revealed the existence of Mg0:95Ni0:05T2O5 as a secondary phase along with the parent Mg0:95Ni0:05Ti0:98Zr0:02O3 phase, which was consistent with the XRD findings. In the present study, εr ~17.1, Qufo~195855 ± 2550 GHz and τf ~ -46 ppm/K was achieved for the synthesized Mg0:95Ni0:05Ti0:98Zr0:02O3 ceramics sintered at 1325 °C for 4 h.

Safety assessment of the biogenic amines in fermented soya beans and fermented bean curd.

Science.gov (United States)

Yang, Juan; Ding, Xiaowen; Qin, Yingrui; Zeng, Yitao

2014-08-06

To evaluate the safety of biogenic amines, high performance liquid chromatography (HPLC) was used to evaluate the levels of biogenic amines in fermented soya beans and fermented bean curd. In fermented soya beans, the total biogenic amines content was in a relatively safe range in many samples, although the concentration of histamine, tyramine, and β-phenethylamine was high enough in some samples to cause a possible safety threat, and 8 of the 30 samples were deemed unsafe. In fermented bean curd, the total biogenic amines content was more than 900 mg/kg in 19 white sufu amples, a level that has been determined to pose a safety hazard; putrescine was the only one detected in all samples and also had the highest concentration, which made samples a safety hazard; the content of tryptamine, β-phenethylamine, tyramine, and histamine had reached the level of threat to human health in some white and green sufu samples, and that may imply another potential safety risk; and 25 of the 33 samples were unsafe. In conclusion, the content of biogenic amines in all fermented soya bean products should be studied and appropriate limits determined to ensure the safety of eating these foods.

Paederia foetida Linn. promoted biogenic gold and silver nanoparticles: Synthesis, characterization, photocatalytic and in vitro efficacy against clinically isolated pathogens.

Science.gov (United States)

Bhuyan, Bishal; Paul, Arijita; Paul, Bappi; Dhar, Siddhartha Sankar; Dutta, Pranab

2017-08-01

Development of newer improved therapeutic agents with efficient antimicrobial activities continues to draw attention of researchers till date. Moreover, abatement of polluting dyes released from industry with enhanced efficiency is currently being considered as challenging task for people working on material sciences. In the present study, we report a facile biogenic synthesis of gold and silver nanoparticles (NPs) in which aqueous extracts of Paederia foetida Linn. was used as reducing as well as stabilizing agent. The biosynthesized Au and Ag NPs were characterized by UV-visible spectroscopy (UV-vis), Fourier transform infrared spectroscopy (FTIR), powder X-ray diffraction analysis (XRD) and transmission electron microscopy (TEM). The photocatalytic activity of these nanoparticles were tested against Rhodamine B (RhB). The antimicrobial activity of these biosynthesized NPs were investigated against four human pathogens viz. B. cereus, E. coli, S. aureus and A. niger. Biogenic silver nanoparticles presented a strong antimicrobial activity against B. cereus (26.13) followed by E. coli (26.02), S. aureus (25.43) and A. niger (22.69). Ag NPs owing to their small size (5-25nm) could have easily penetrate into the cell membrane, disturb the metabolism, cause irretrievable damage finally leading to the microbial cell death. Interestingly biogenic gold nanoparticles didn't show any antimicrobial activity. Copyright © 2017 Elsevier B.V. All rights reserved.

Enhanced photocatalytic properties of the 3D flower-like Mg-Al layered double hydroxides decorated with Ag{sub 2}CO{sub 3} under visible light illumination

Energy Technology Data Exchange (ETDEWEB)

Ao, Yanhui, E-mail: andyao@hhu.edu.cn; Wang, Dandan; Wang, Peifang; Wang, Chao; Hou, Jun; Qian, Jin

2016-08-15

Highlights: • 3D flower-like Ag{sub 2}CO{sub 3}/Mg-Al layered double hydroxide composite was prepared. • The nanocomposites exhibited high photocatalytic activities on different organic pollutants. • The mechanism of the enhanced activity were investigated. - Abstract: A facile anion-exchange precipitation method was employed to synthesize 3D flower-like Ag{sub 2}CO{sub 3}/Mg-Al layered double hydroxide composite photocatalyst. Results showed that Ag{sub 2}CO{sub 3} nanoparticles dispersed uniformly on the petals of the flower-like Mg-Al LDH. The obtained nanocomposites exhibited high photocatalytic activities on different organic pollutants (cationic and anionic dyes, phenol) under visible light illumination. The high photocatalytic activity can be ascribed to the special structure which accomplishes the wide-distribution of Ag{sub 2}CO{sub 3} nanoparticles on the surfaces of the 3D flower-like nanocomposites. Therefore, it can provide much more active sites for the degradation of organic pollutant. Then the photocatalytic mechanism was also verified by reactive species trapping experiments in detail. The work would pave a facile way to prepare LDHs based hierarchical photocatalysts with high activity for the degradation of wide range organic pollutants under visible light irradiation.

Ethylbenzene dehydrogenation over Mg3Fe0.5−xCoxAl0.5 catalysts derived from hydrotalcites: Comparison with Mg3Fe0.5−yNiyAl0.5 catalysts

KAUST Repository

Atanda, Luqman A.

2011-04-01

A series of Mg3Fe0.5-xCoxAl0.5 (x = 0-0.5) catalysts were prepared from hydrotalcite precursors and their activities in the dehydrogenation of ethylbenzene were compared with those of a series of Mg3Fe0.5-yNiyAl0.5 (y = 0-0.5) catalysts also derived from hydrotalcite. The hydrotalcites prepared by co-precipitation were calcined at 550 °C to the mixed oxides with a high surface area of 150-240m2gcat-1; they were composed of Mg(Fe,Me,Al)O periclase and Mg(Me)(Fe,Al)2O4 spinel (Me = Co or Ni). Bimetallic Fe3+-Co2+ system showed a synergy, i.e., an increase in the activity, whereas Fe3+-Ni2+ bimetallic system showed no synergy. The high styrene yield was obtained on Mg 3Fe0.1Co0.4Al0.5; however, a large substitution of Fe3+ with Co2+ caused a decrease in styrene selectivity along with coking on the catalysts, due to an isolation of CoOx on the catalyst surface. The highest yield as well as the highest selectivity for styrene production was obtained at x = 0.25 at time on stream of 30 min. The coprecipitation at pH = 10.0 and the composition of Mg3Fe0.25Co0.25Al0.5 were the best for preparing the active catalyst. This is partly due to the formation of a good hydrotalcite structure. On this catalyst, the active Fe3+ species was reduced at a low temperature by the Fe3+-Co2+ bimetal formation, leading to a high activity. Simultaneously, the amount of reducible Fe3+ was the smallest, resulting in a high stability of the active Fe3+ species. It is likely that the dehydrogenation was catalyzed by the reduction-oxidation between Fe3+ and Fe2+ and that Co2+ assisted the reduction-oxidation by forming Fe 3+-Co2+ (1/1) bimetallic active species. © 2011 Elsevier B.V. All rights reserved.

Biogenic gas in the Cambrian-Ordovcian Alum Shale (Denmark and Sweden)

Energy Technology Data Exchange (ETDEWEB)

Schulz, H.M.; Wirth, R.; Biermann, S.; Arning, E.T. [Helmholtz-Zentrum Potsdam - Deutsches GeoForschungsZentrum GFZ, Potsdam (Germany); Krueger, M.; Straaten, N. [BGR Hannover (Germany); Bechtel, A. [Montanuniv. Leoben (Austria); Berk, W. van [Technical Univ. of Clausthal (Germany); Schovsbo, N.H. [Geological Survey of Denmark and Greenland - GEUS, Copenhagen (Denmark); Crabtree, Stephen [Gripen Gas (Sweden)

2013-08-01

Shale gas is mainly produced from thermally mature black shales. However, biogenic methane also represents a resource which is often underestimated. Today biogenic methane is being produced from the Upper Devonian Antrim Shale in the Michigan Basin which was the most successfully exploited shale gas system during the 1990-2000 decade in the U.S.A. before significant gas production from the Barnett Shale started (Curtis et al., 2008). The Cambro-Ordovician Alum Shale in northern Europe has thermal maturities ranging from overmature in southern areas (Denmark and southern Sweden) to immature conditions (central Sweden). Biogenic methane is recorded during drilling in central Sweden. The immature Alum Shale in central Sweden has total organic carbon (TOC) contents up to 20 wt%. The hydrogen index HI ranges from 380 to 560 mgHC/gTOC at very low oxygen index (OI) values of around 4 mg CO{sub 2}/gTOC, Tmax ranges between 420 - 430 C. The organic matter is highly porous. In general, the Alum Shale is a dense shale with intercalated sandy beds which may be dense due to carbonate cementation. Secondary porosity is created in some sandy beds due to feldspar dissolution and these beds serve as gas conduits. Methane production rates with shale as substrate in the laboratory are dependent on the kind of hydrocarbon-degrading microbial enrichment cultures used in the incubation experiments, ranging from 10-620 nmol/(g*d). In these experiments, the CO{sub 2} production rate was always higher than for methane. Like the northern part of North America, also Northern European has been covered by glaciers during the Pleistocene and similar geological processes may have developed leading to biogenic shale gas formation. For the Antrim Shale one hypothesis suggests that fresh waters, recharged from Pleistocene glaciation and modern precipitation, suppressed basinal brine salinity along the northern margins of the Michigan Basin to greater depths and thereby enhancing methanogenesis

Monitoring of biogenic amines in cheeses manufactured at small-scale farms and in fermented dairy products in the Czech Republic.

Science.gov (United States)

Buňková, Leona; Adamcová, Gabriela; Hudcová, Kateřina; Velichová, Helena; Pachlová, Vendula; Lorencová, Eva; Buňka, František

2013-11-01

The aim of the study was the monitoring of six biogenic amines (histamine, tyramine, phenylethylamine, tryptamine, putrescine, and cadaverine) and two polyamines (spermidine and spermine) in 112 samples of dairy products purchased in the Czech Republic, namely in 55 cheeses made in small-scale farms and in 57 fermented dairy products. The products were tested at the end of their shelf-life period. Neither tryptamine nor phenylethylamine was detected in the monitored samples; histamine was found only in four cheese samples containing up to 25mg/kg. The contents of spermine and spermidine were low and did not exceed the values of 35 mg/kg. Significant amounts of tyramine, putrescine, and cadaverine occurred especially in cheeses produced from ewe's milk or in long-term ripened cheeses. In about 10% of the tested cheeses, the total concentration of all the monitored biogenic amines and polyamines exceeded the level of 200mg/kg, which can be considered toxicologically significant. In fermented dairy products, the tested biogenic amines occurred in relatively low amounts (generally up to 30 mg/kg) that are regarded safe for the consumer's health. Copyright © 2013 Elsevier Ltd. All rights reserved.

Microwave characteristics of sol-gel based Ag-doped (Ba{sub 0.6}Sr{sub 0.4})TiO{sub 3} thin films

Energy Technology Data Exchange (ETDEWEB)

Kim, Kyoung-Tae; Kim, Cheolbok [Department of Electrical and Computer Engineering, University of Florida, Gainesville, FL 32611 (United States); Senior, David E. [Department of Electrical and Computer Engineering, University of Florida, Gainesville, FL 32611 (United States); Department of Electrical and Electronic Engineering, Universidad Tecnológica de Bolívar Cartagena, 130011 Colombia (Colombia); Kim, Dongsu [Packaging Research Center, Korea Electronics Technology Institute, Gyeonggi-do, 463-816 (Korea, Republic of); Yoon, Yong-Kyu, E-mail: ykyoon@ece.ufl.edu [Department of Electrical and Computer Engineering, University of Florida, Gainesville, FL 32611 (United States)

2014-08-28

Dielectric Ba{sub 0.6}Sr{sub 0.4}TiO{sub 3} (BST) thin films with a different concentration of Ag-dopant of 0.5, 1, 1.5, 2, 3, and 5 mol % have been prepared using an alkoxide-based sol-gel method on a Pt(111)/TiO{sub 2}/SiO{sub 2}/Si substrate and their surface morphology and crystallinity have been examined using scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis, respectively. An on-chip metal-insulator-metal capacitor has been fabricated with the prepared thin film ferroelectric sample. Concentric coplanar electrodes are used for high frequency electrical characterization with a vector network analyzer and a probe station. The SEM images show that increasing Ag doping concentration leads to a decrease in grain size. XRD reveals that the fabricated films show good BST crystallinity for all the concentration while a doping concentration of 5 mol % starts to show an Ag peak, implying a metallic phase. Improved microwave dielectric loss properties of the BST thin films are observed in a low Ag doping level. Especially, BST with an Ag doping concentration of 1 mol % shows the best properties with a dielectric constant of 269.3, a quality factor of 48.1, a tunability at the electric field of 100 kV/cm of 41.2 %, a leakage-current density of 1.045 × 10{sup −7}A/cm{sup 2} at an electric field of 100 kV/cm and a figure of merit (defined by tunability (%) divided by tan δ (%)) of 19.59 under a dc bias voltage of 10 V at 1 GHz. - Highlights: • High quality Ag-doped Ba{sub 0.6}Sr{sub 0.4}TiO{sub 3} (BST) thin films were derived by the sol-gel method. • Doped Ag replaced the A site ions in the ABO{sub 3} type structure. • Doped Ag helped lower leakage current by filling oxygen vacancies, which is a leakage path. • Microwave characteristics of low dielectric loss and good tunability were confirmed. • Great potential is envisioned for low loss tunable microwave applications.

Giant magneto resistance and temperature coefficient of resistance in Sm0.55Sr0.30Ag0.15MnO3 perovskite

Directory of Open Access Journals (Sweden)

Masroor Ahmad Bhat

2016-12-01

Full Text Available Silver ions substituted samarium strontium manganite (Sm0.55Sr0.30Ag0.15MnO3 pervoskite was synthesized by using respective oxides in stoichiometric ratio through solid state reaction. The as-prepared sample was characterized by various analytical techniques to confirm its formation and understand the effect of monovalent silver ions in pervoskite lattice. X-ray diffraction pattern confirms the single phase formation while grain morphology in SEM image indicates good connectivity among the grains. The enhancement in metal to insulator transition temperature shows quenched disorder and magnetoresistance phenomena. The magnetoresistance (MR and temperature coefficient of resistance (TCR emerge from grain growth factor and homogeneity induced by Ag+ ions in the lattice. The reduction in hysteresis loss resulted from antiferromagnetic - ferromagnetic (TN and ferromagnetic - paramagnetic (Tc transitions reveals the removal of disorder in perovskite lattice by Ag+ ions substitution. This increases the magnetic moment across distinct ions on the applying magnetic field. The rise in MR% (~99% with silver doping emerging from smooth spin tunneling of the grains across the boundary and suppression of the disordered magnetic fluctuations with increase in magnetic field has been reported. The present compound exhibits the first order nature of magnetism and observed first time the highest value of TCR ~ 95%.

Structural characterization of Fe/Ag bilayers by RBS and AFM

International Nuclear Information System (INIS)

Tunyogi, A.; Tancziko, F.; Osvath, Z.; Paszti, F.

2008-01-01

Fe/Ag thin films are intensively investigated due to their special magnetic properties. Recently a deposition-order dependent asymmetric interface has been found. When iron is grown on silver, the interface is sharp, while the growth of Ag on Fe results in a long, low-energy tail of the Ag peak in the Rutherford backscattering spectrometry (RBS) spectra. The main purpose of this paper is to show that the low-energy Ag tail is caused by grain boundary diffusion, and that, when elevating the growing temperature of the Ag layer this effect becomes more significant. Two sets of polycrystalline and epitaxial Fe/Ag bilayers were prepared simultaneously onto Si(1 1 1) and MgO(1 0 0), respectively. The iron layers were grown at 250 deg. C and annealed at 450 deg. C in both sets, while the Ag layer was grown in the first set at room temperature (RT) and in the second set at 250 deg. C (HT). The sample composition, the interface sharpness and the quality of the epitaxy were studied by Rutherford backscattering spectrometry (RBS) combined with channeling effect. The surface morphology was determined by atomic force microscopy (AFM). RBS spectra show that in the case of RT samples the epitaxial MgO/Fe/Ag bilayer has sharp, well-defined interface, while for the polycrystalline Si/Fe/Ag sample the silver peak has a low-energy tail. Both the Fe and Ag peaks smeared out in the case of HT samples. AFM-images show that the RT samples have a continuous Ag layer, while the HT samples have fragmented surfaces. The RBS spectra taken on the HT samples were successfully simulated by the RBS-MAST code taking into account their fragmented structures.

Structural, morphological and optical properties of LiCo0.5Ni0.45Ag0.05O2 thin films

Science.gov (United States)

Haider, Adawiya J.; AL-Rsool, Rusul Abed; AL-Tabbakh, Ahmed A.; Al-Gebori, Abdul Nasser M.; Mohamed, Aliaa

2018-05-01

Pulsed Laser Deposition (PLD) method has been successfully used for the synthesized of nano-crystalline cathode m aterial LiCo0.5Ni0.45Ag0.05O2 (LCNAO) thin film. LCNAO Ferromagnetic using pulsed Nd-YAG laser with wavelength (λ = 532 nm) and duration (10 ns) and energy fluence (1.4 J/cm2) with different substrate temperature (100, 200, 300) ˚C and O2 pressure at 10 mbar. The structural, morphological and optical properties of the films were determined by X-ray Diffraction (XRD), Scan Electron Microscopy (SEM), Atomic Force microscope (AFM) and UV-VIS spectroscopy respectively. It is observed that partial layer to spinel transformation takes place during post annealing and the average particle size of the LiCo0.5Ni0.45Ag0.05O2 is found to be (1-12) nm from SEM measurement. Finally the optical properties of the thin films have been studied at different Substrate temperature. It found the energy gap decreases from 4.2 to 3.8 eV when the substrate's temperature increasing from 100° C into 300 °C of the LCNAO films. These mean that the optical quality of LCNAO films is improved due to the increase in crystalline size and reduction of defect sites.

Hardness and microstructure of Al-10.0 wt% Zn-4.0 wt% Mg alloy

International Nuclear Information System (INIS)

Iqbal, M.; Shaikh, M.A.; Ahmad, W.; Ali, K.L.

1996-01-01

Al-Zn-Mg alloys are widely used in industries as these have excellent physical and mechanical properties. However some aspects of the effect of heat treatment on these alloys are not yet clear. In order to understand the precipitation phenomena in these alloys, microstructure of a locally prepared alloy Al-10.0 wt% Zn-4.0 wt% Mg heat treated under different conditions has been examined in scanning electron microscope/electron probe micro analyser. Precipitates MgZn/sub 2/, MgZn/sub 4/ and Mg/sub 2/Zn/sub 11/ have been observed and these are caused by heat treatment. Correlation between these precipitates and Vickers's hardness has also been studied. In the present paper results of this investigation have been presented and discussed. (author)

Sn-In-Ag phase equilibria and Sn-In-(Ag)/Ag interfacial reactions

International Nuclear Information System (INIS)

Chen Sinnwen; Lee Wanyu; Hsu Chiaming; Yang Chingfeng; Hsu Hsinyun; Wu Hsinjay

2011-01-01

Research highlights: → Thermodynamic models of Sn-In and Sn-In-Ag are developed using the CALPHAD approach. → Reaction layer in the Sn-In-(Ag)/Ag couples at 100 deg. C is thinner than those at 25 deg. C, 50 deg. C, and 75 deg. C. → Reactions in the Sn-20 wt%In-2.8 wt%Ag/Ag couples are faster than those in the Sn-20 wt%In/Ag couples. - Abstract: Experimental verifications of the Sn-In and Sn-In-Ag phase equilibria have been conducted. The experimental measurements of phase equilibria and thermodynamic properties are used for thermodynamic modeling by the CALPHAD approach. The calculated results are in good agreement with experimental results. Interfacial reactions in the Sn-In-(Ag)/Ag couples have been examined. Both Ag 2 In and AgIn 2 phases are formed in the Sn-51.0 wt%In/Ag couples reacted at 100 and 150 deg. C, and only the Ag 2 In phase is formed when reacted at 25, 50 and 75 deg. C. Due to the different growth rates of different reaction phases, the reaction layer at 100 deg. C is thinner than those at 25 deg. C, 50 deg. C, and 75 deg. C. In the Sn-20.0 wt%In/Ag couples, the ζ phase is formed at 250 deg. C and ζ/AgIn 2 phases are formed at 125 deg. C. Compared with the Sn-20 wt%In/Ag couples, faster interfacial reactions are observed in the Sn-20.0 wt%In-2.8 wt%Ag/Ag couples, and minor Ag addition to Sn-20 wt%In solder increases the growth rates of the reaction phases.

Effect of nano Co reinforcements on the structure of the Sn-3.0Ag-0.5Cu solder in liquid and after reflow solid states

Energy Technology Data Exchange (ETDEWEB)

Yakymovych, Andriy, E-mail: yakymovych@univie.ac.at [Department of Inorganic Chemistry – Functional Materials, University of Vienna, Währinger Str. 42, 1090 Vienna (Austria); Department of Metal Physics, Ivan Franko National University of Lviv, Kyrylo i Mephodiy Str. 8, 79005 Lviv (Ukraine); Mudry, Stepan; Shtablavyi, Ihor [Department of Metal Physics, Ivan Franko National University of Lviv, Kyrylo i Mephodiy Str. 8, 79005 Lviv (Ukraine); Ipser, Herbert [Department of Inorganic Chemistry – Functional Materials, University of Vienna, Währinger Str. 42, 1090 Vienna (Austria)

2016-09-15

Sn-Ag-Cu (SAC) alloys are commonly recognized as lead-free solders employed in the electronics industry. However, some disadvantages in mechanical properties and their higher melting temperatures compared to Pb-Sn solders prompt new research relating to reinforcement of existing SAC solders. One of the ways to reinforce these solder materials is the formation of composites with nanoparticles as filler materials. Accordingly, this study presents structural features of nanocomposite (Sn-3.0Ag-0.5Cu){sub 100−x}(nanoCo){sub x} solders with up to 0.8 wt% nano Co. The effect of nano-sized Co particles was investigated by means of differential thermal analysis (DTA), X-ray diffraction (XRD) in both liquid and solid states, and scanning electron microscopy (SEM). The experimental data of DTA are compared with available literature data for bulk Sn-3.0Ag-0.5Cu alloy to check the capability of minor nano-inclusions to decrease the melting temperature of the SAC solder. The combination of structural data in liquid and solid states provides important information about the structural transformations of liquid Sn-3.0Ag-0.5Cu alloys caused by minor Co additions and the phase formation during crystallization. Furthermore, scanning electron microscopy has shown the mutual substitution of Co and Cu atoms in the Cu{sub 6}Sn{sub 5} and CoSn{sub 3} phases, respectively. - Highlights: • Differential thermal analysis of nanocomposite (Sn-3.0Ag-0.5Cu){sub 100−x}(nanoCo){sub x} alloys. • Structural transformations of liquid Sn-3.0Ag-0.5Cu solder by minor Co additions. • Structure data of the solid quaternary (Sn-3.0Ag-0.5Cu){sub 100−x}(Co){sub x} alloys. • Substitution of Co and Cu atoms in the Cu{sub 6}Sn{sub 5} and CoSn{sub 3} phases.

Influence of In{sup 3+}-doping and Ag{sup 0}-depositing on the visible-light-induced photocatalytic activity of TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Zhang, Pengfei, E-mail: zpf@mail.csu.edu.cn [College of Chemistry and Chemical Engineering, Central South University, Changsha, Hunan, 410083 (China); Li, Xiaowei; Wu, Xingke [College of Chemistry and Chemical Engineering, Central South University, Changsha, Hunan, 410083 (China); Zhao, Tianxiang [College of Physical Science and Technology, Central South University, Changsha, 410083 (China); Wen, Lishi [Metal Graduate School, Chinese Academy of Sciences, Shenyang, Liaoning, 110016 (China)

2016-07-15

-light-induced photocatalytic activity than either pure or single-modified one. The degradation rate of MB in aqueous solution (8 mg/L) reached 90% after 7 h visible light irradiation over Ag{sup 0}/In{sup 3+}/TiO{sub 2} (5 g/L), while pure TiO{sub 2} showed only 40% under the same conditions. - Highlights: • In{sup 3+}-doped and Ag{sup 0}-deposited TiO{sub 2} was reported for the first time. • The co-modifying's synergistic effects was discovered. • The co-modifying extended the absorption limit to 670 nm by synergistic effect. • The co-modifying promoted e{sup –}/h{sup +} separation efficiently by synergistic effect. • The co-modified TiO{sub 2} exhibited higher visible-light-induced photocatalytic activity.

Evolution of cyclonic eddies and biogenic fluxes in the northern Bay of Bengal

Digital Repository Service at National Institute of Oceanography (India)

Nuncio, M.; PrasannaKumar, S.

in the sediment trap location. Cyclonic eddy-induced down ward biogenic flux in the sediment trap location was larger than the amplitude, ~40 mg m^-2 d^-1, of the seasonal cycle. The magnitude of the peak episodic fluxes were one...

A density functional study of NO{sub 2} adsorption on perfect and defective MgO (1 0 0) and Li/MgO (1 0 0) surfaces

Energy Technology Data Exchange (ETDEWEB)

Eid, Kh.M., E-mail: Khaled_eid@edu.asu.edu.eg [Physics Department, Faculty of Education, Ain Shams University, P.O. Box 11757, Cairo (Egypt); Ammar, H.Y. [Physics Department, Faculty of Education, Ain Shams University, P.O. Box 11757, Cairo (Egypt); Department of Physics, Faculty of Science, Najran University, Najran (Saudi Arabia)

2012-07-15

The density functional theory (DFT) in combination with embedded cluster model have been used to study the adsorption of nitrogen dioxide molecule (NO{sub 2}) on Li atom deposited on the surfaces of metal oxide MgO (1 0 0) on both anionic (O{sup 2-}) and defect (F{sub s} and F{sub s}{sup +}-centers) sites. The adsorption energy (E{sub ads}) of NO{sub 2} molecule (N-down as well as O-down) in different positions on O{sup -2}, F{sub s} and F{sub s}{sup +}-sites is considered. The geometrical optimizations have been done for the additive materials and MgO substrate surfaces. The formation energies have been evaluated for F{sub s} and F{sub s}{sup +} of MgO substrate surfaces. The ionization potential (IP) and electron affinity (eA) for defect free and defect containing surfaces have been calculated. The adsorption properties of NO{sub 2} are analyzed in terms of the adsorption energy, the electron donation (basicity), the elongation of N-O bond length and the atomic charges on adsorbed materials. The densities of states (DOS) have been calculated and used for examining the adsorption properties. The NO{sub 2} molecule is dissociated due to the interaction with the defective substrate surface (F{sub s}-site) producing an oxygen atom strongly chemisorbed to the vacancy of the substrate and gaseous NO far away from the surface. The presence of the Li atom increases the surface chemistry of the anionic O{sup 2-}-site of MgO substrate surfaces (converted from physisorption to chemisorption). On the other hand, the presence of the Li atom decreases the surface chemistry of the F{sub s} and F{sub s}{sup +}-sites of MgO substrate surfaces. Generally, the NO{sub 2} molecule is strongly adsorbed (chemisorption) on the MgO substrate surfaces containing F{sub s} and F{sub s}{sup +}-centers.

Mechanical Deformation Behavior of Sn-Ag-Cu Solders with Minor Addition of 0.05 wt.% Ni

Science.gov (United States)

Hammad, A. E.; El-Taher, A. M.

2014-11-01

The aim of the present work is to develop a comparative evaluation of the microstructural and mechanical deformation behavior of Sn-Ag-Cu (SAC) solders with the minor addition of 0.05 wt.% Ni. Test results showed that, by adding 0.05Ni element into SAC solders, generated mainly small rod-shaped (Cu,Ni)6Sn5 intermetallic compounds (IMCs) inside the β-Sn phase. Moreover, increasing the Ag content and adding Ni could result in the change of the shape and size of the IMC precipitate. Hence, a significant improvement is observed in the mechanical properties of SAC solders with increasing Ag content and Ni addition. On the other hand, the tensile results of Ni-doped SAC solders showed that both the yield stress and ultimate tensile strengths decrease with increasing temperature and with decreasing strain rate. This behavior was attributed to the competing effects of work hardening and dynamic recovery processes. The Sn-2.0Ag-0.5Cu-0.05Ni solder displayed the highest mechanical properties due to the formation of hard (Cu,Ni)6Sn5 IMCs. Based on the obtained stress exponents and activation energies, it is suggested that the dominant deformation mechanism in SAC (205)-, SAC (0505)- and SAC (0505)-0.05Ni solders is pipe diffusion, and lattice self-diffusion in SAC (205)-0.05Ni solder. In view of these results, the Sn-2.0Ag-0.5Cu-0.05Ni alloy is a more reliable solder alloy with improved properties compared with other solder alloys tested in the present work.

The influences of fish infusion broth on the biogenic amines formation by lactic acid bacteria

Directory of Open Access Journals (Sweden)

Esmeray Küley

2013-01-01

Full Text Available The influences of fish infusion decarboxylase broth (IDB on biogenic amines (BA formation by lactic acid bacteria (LAB were investigated. BA productions by single LAB strains were tested in five different fish (anchovy, mackerel, white shark, sardine and gilthead seabream IDB. The result of the study showed that significant differences in ammonia (AMN and BA production were observed among the LAB strains in fish IDB (p < 0.05. The highest AMN and TMA production by LAB strains were observed for white shark IDB. The all tested bacteria had decarboxylation activity in fish IDB. The uppermost accumulated amines by LAB strains were tyramine (TYM, dopamine, serotonin and spermidine. The maximum histamine production was observed in sardine (101.69 mg/L and mackerel (100.84 mg/L IDB by Leuconostoc mesenteroides subsp. cremoris and Pediococcus acidophilus, respectively. Lactobacillus delbrueckii subsp. lactis and Pediococcus acidophilus had a high TYM producing capability (2943 mg/L and 1157 mg/L in sardine IDB.

Unique dielectric features of a ceramic-semiconductor nanocomposite MgNb2O6 + 0.25Zn0.5Cd0.5S

Science.gov (United States)

Pukazhselvan, D.; Selvaraj, Nivas Babu; Bdikin, Igor; Saravanan, R. Sakthi Sudar; Jakka, Suresh Kumar; Soares, M. J.; Fagg, Duncan Paul

2017-12-01

The present communication deals with the optical/dielectric characteristics of MgNb2O6 + 0.25Zn0.5Cd0.5S nanocomposite (10-30 nm) mixture. Zn0.5Cd0.5S (size ∼10 nm) was synthesized by microwave assisted solvo-thermal method. Monophase magnesium niobate (MN) nanoparticles (10-20 nm) were synthesized in a single step by mechanochemical treatment of MgO + Nb2O5 under dry N2 atmosphere. The nanocomposite, MgNb2O6 + 0.25Zn0.5Cd0.5S, was prepared by mechanical admixing of MgNb2O6 and Zn0.5Cd0.5S taken in 4:1 molar ratio. The photoluminescence study shows violet, yellow and orange-red emissions by the MgNb2O6 + 0.25Zn0.5Cd0.5S composite. The observed dielectric constant value (ε) for MgNb2O6 + 0.25Zn0.5Cd0.5S is only 4.7, which is ∼5 times smaller than the ε value of MgNb2O6 while a dielectric loss for the composite being closer to zero ensures promising commercial applications.

Photocatalytic activity of biogenic silver nanoparticles synthesized using potato (Solanum tuberosum) infusion.

Science.gov (United States)

Roy, Kaushik; Sarkar, C K; Ghosh, C K

2015-07-05

In this study, we have reported a fast and eco-benign procedure to synthesis silver nanoparticle at room temperature using potato (Solanum tuberosum) infusion along with the study of its photocatalytic activity on methyl orange dye. After addition of potato infusion to silver nitrate solution, the color of the mixture changed indicating formation of silver nanoparticles. Time dependent UV-Vis spectra were obtained to study the rate of nanoparticle formation with time. Purity and crystallinity of the biogenic silver nanoparticles were examined by X-ray diffraction (XRD). Average size and morphology of the nanoparticles were characterized by dynamic light scattering (DLS) and transmission electron microscopy (TEM). Fourier transform infra-red spectroscopy (FTIR) was employed to detect functional bio-molecules responsible that contribute to the reduction and capping of biosynthesized Ag nanoparticles. Further, these synthesized nanoparticles were used to investigate their ability to degrade methyl orange dye under sunlight irradiation and the results showed effective photocatalytic property of these biogenic silver nanoparticles. Copyright © 2015 Elsevier B.V. All rights reserved.

Enhanced Performance of Mg0.1Zn0.9O UV Photodetectors Using Photoelectrochemical Treatment and Silica Nanospheres

Directory of Open Access Journals (Sweden)

Hsin-Ying Lee

2014-01-01

Full Text Available The Mg0.1Zn0.9O films were grown using atomic layer deposition (ALD system and applied to metal-semiconductor-metal ultraviolet photodetectors (MSM-UPDs as an active layer. To suppress the dangling bonds on the Mg0.1Zn0.9O surface, the photoelectrochemical (PEC treatment was used to passivate the Mg0.1Zn0.9O surface, which could reduce the dark current of the MSM-UPDs about one order. Beside, to increase more incident light into the Mg0.1Zn0.9O active layer of the MSM-UPDs, the 500-nm-diameter silica nanospheres were spin-coated on the Mg0.1Zn0.9O active layer to improve the antireflection capability at the wavelength of 340 nm. The reflectivity of the Mg0.1Zn0.9O films with silica nanospheres antireflection layer decreased about 7.0% in comparison with the Mg0.1Zn0.9O films without silica nanospheres. The photocurrent and UV-visible ratio of the passivated Mg0.1Zn0.9O MSM-UPDs with antireflection layer were enhanced to 5.85 μA and 1.44×104, respectively, at the bias voltage of 5 V. Moreover, the noise equivalent power and the specific detectivity of the passivated Mg0.1Zn0.9O MSM-UPDs with antireflection layer were decreased to 2.60×10-13 W and increased to 1.21×1012 cmHz1/2W−1, respectively, at the bias voltage of 5 V. According to the above mentions, the PEC treatment and silica nanospheres antireflection layer could effectively enhance the performance of Mg0.1Zn0.9O MSM-UPDs.

Conductivity and Structure of Superionic Composite (AgI0.6(NaPO30.4

Directory of Open Access Journals (Sweden)

E. Kartini

2005-01-01

Full Text Available Superionic conductors are of considerable interest from both application and fundamental points of view. Superionic solid electrolytes can be used for batteries, fuel cells and sensors. We have used melt quenching to make a new superionic composite (AgI0.6(NaPO30.4 which exhibits an ionic conductivity of about 2 x 10-4 S/cm at ambient temperature. The conductivity of crystalline AgI and NaPO3 glass are lower of orders of magnitude. (AgI0.6(NaPO30.4 is a composite material containing both crystalline and glass phases. The paper presents the conductivity as a function of temperature measured by impedance spectroscopy and the crystal structure performed by a high resolution powder diffractometer, VEGA at the Neutron Science Laboratory (KENS, KEK, Japan.

Effect of irradiation and storage on biogenic amine contents in ripened Egyptian smoked cooked sausage

International Nuclear Information System (INIS)

Rabie, Mohamed A.; Toliba, Abbas O.

2013-01-01

The effects of γ-irradiation upon the biogenic amine inventory in Egyptian smoked cooked sausages were investigated for the first time during storage for up to 90 days at 4 ° C. Typical contents of biogenic amines in non-irradiated sausages ranged between 125.50 and 596.18 mg/kgDW; irradiation with 4 and 6 kGy decreased said total contents to 105.20-94.82 and 104.98-26.44 mg/kgDW respectively, by the end of storage. Putrescine and cadaverine were the major amines in non-irradiated samples - where it accounted for 33% and 29% respectively, of the total by 90 days; however, tyramine dominated in irradiated samples with 2, 4 and 6 kGy, where it accounted for 44, 52 and 42%. On the other hand, the histamine content in non-irradiated sausage by 90 days of storage (i.e. 109.12 mg/kgDW) clearly exceeded the maximum allowable of 50 mg/kg, unlike happened in their irradiated counterparts. Therefore, the dramatic reduction observed in the histamine levels suggests use of this preservation technique for that traditional meat food. (author)

[Diagnostic advantages of the test system "DS-EIA-HBsAg-0.01" for detection of HBV surface antigen].

Science.gov (United States)

Egorova, N I; Pyrenkova, I Iu; Igolkina, S N; Sharipova, I N; Puzyrev, V F; Obriadina, A P; Burkov, A N; Kornienko, N V; Fields, H A; Korovkin, A S; Shalunova, N V; Bektemirov, T A; Kuznetsov, K V; Koshcheeva, N A; Ulanova, T I

2009-01-01

The new highly sensitive test system "DS-EIA-HBsAg-0.01" (Priority Certificate No. 2006129019 of August 10, 2006) in detecting hepatitis B surface antigen (HBsAg) was assessed. The sensitivity of the test was estimated using the federal standards sample HBsAg 42-28-311-06, panels' samples Boston Biomedica Inc. (West Bridgewater, Mass, USA) and ZeptoMetrix Corp. (Buffalo, NY, USA). The findings have indicated that "DS-EIA-HBsAg-0.01" is equally effective in detecting different subtypes of HBsAg during a seroconversion period earlier than alternative assays. Along with its high analytical and diagnostic sensitivity, the system shows a high diagnostic specificity.

Hydrothermal replacement of biogenic and abiogenic aragonite by Mg-carbonates - Relation between textural control on effective element fluxes and resulting carbonate phase

Science.gov (United States)

Jonas, Laura; Müller, Thomas; Dohmen, Ralf; Immenhauser, Adrian; Putlitz, Benita

2017-01-01

Dolomitization, i.e., the secondary replacement of calcite or aragonite (CaCO3) by dolomite (CaMg[CO3]2), is one of the most volumetrically important carbonate diagenetic processes. It occurs under near surface and shallow burial conditions and can significantly modify rock properties through changes in porosity and permeability. Dolomitization fronts are directly coupled to fluid pathways, which may be related to the initial porosity/permeability of the precursor limestone, an existing fault network or secondary porosity/permeability created through the replacement reaction. In this study, the textural control on the replacement of biogenic and abiogenic aragonite by Mg-carbonates, that are typical precursor phases in the dolomitization process, was experimentally studied under hydrothermal conditions. Aragonite samples with different textural and microstructural properties exhibiting a compact (inorganic aragonite single crystal), an intermediate (bivalve shell of Arctica islandica) and open porous structure (skeleton of coral Porites sp.) were reacted with a solution of 0.9 M MgCl2 and 0.015 M SrCl2 at 200 °C. The replacement of aragonite by a Ca-bearing magnesite and a Mg-Ca carbonate of non-stoichiometric dolomitic composition takes place via a dissolution-precipitation process and leads to the formation of a porous reaction front that progressively replaces the aragonite precursor. The reaction leads to the development of porosity within the reaction front and distinctive microstructures such as gaps and cavities at the reaction interface. The newly formed reaction rim consists of chemically distinct phases separated by sharp boundaries. It was found that the number of phases and their chemical variation decreases with increasing initial porosity and reactive surface area. This observation is explained by variations in effective element fluxes that result in differential chemical gradients in the fluid within the pore space of the reaction rim. Observed

O- centers in LuAG:Ce,Mg ceramics

Czech Academy of Sciences Publication Activity Database

Hu, C.; Liu, S.; Fasoli, M.; Vedda, A.; Nikl, Martin; Feng, X. Q.; Pan, Y.B.

2015-01-01

Roč. 9, č. 4 (2015), s. 245-249 ISSN 1862-6254 R&D Projects: GA ČR GAP204/12/0805 Institutional support: RVO:68378271 Keywords : scintillator * hole center * EPR * LuAG * Ce 3+ Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.578, year: 2015

Microstructure and Tensile Properties of Sn-1Ag-0.5Cu Solder Alloy Bearing Al for Electronics Applications

Science.gov (United States)

Shnawah, Dhafer Abdul-Ameer; Said, Suhana Binti Mohd; Sabri, Mohd Faizul Mohd; Badruddin, Irfan Anjum; Hoe, Teh Guan; Che, Fa Xing; Abood, Adnan Naama

2012-08-01

This work investigates the effects of 0.1 wt.% and 0.5 wt.% Al additions on bulk alloy microstructure and tensile properties as well as on the thermal behavior of Sn-1Ag-0.5Cu (SAC105) lead-free solder alloy. The addition of 0.1 wt.% Al reduces the amount of Ag3Sn intermetallic compound (IMC) particles and leads to the formation of larger ternary Sn-Ag-Al IMC particles. However, the addition of 0.5 wt.% Al suppresses the formation of Ag3Sn IMC particles and leads to a large amount of fine Al-Ag IMC particles. Moreover, both 0.1 wt.% and 0.5 wt.% Al additions suppress the formation of Cu6Sn5 IMC particles and lead to the formation of larger Al-Cu IMC particles. The 0.1 wt.% Al-added solder shows a microstructure with coarse β-Sn dendrites. However, the addition of 0.5 wt.% Al has a great effect on suppressing the undercooling and refinement of the β-Sn dendrites. In addition to coarse β-Sn dendrites, the formation of large Sn-Ag-Al and Al-Cu IMC particles significantly reduces the elastic modulus and yield strength for the SAC105 alloy containing 0.1 wt.% Al. On the other hand, the fine β-Sn dendrite and the second-phase dispersion strengthening mechanism through the formation of fine Al-Ag IMC particles significantly increases the elastic modulus and yield strength of the SAC105 alloy containing 0.5 wt.% Al. Moreover, both 0.1 wt.% and 0.5 wt.% Al additions worsen the elongation. However, the reduction in elongation is much stronger, and brittle fracture occurs instead of ductile fracture, with 0.5 wt.% Al addition. The two additions of Al increase both solidus and liquidus temperatures. With 0.5 wt.% Al addition the pasty range is significantly reduced and the differential scanning calorimetry (DSC) endotherm curve gradually shifts from a dual to a single endothermic peak.

Raman spectroscopy, dielectric properties and phase transitions of Ag{sub 0.96}Li{sub 0.04}NbO{sub 3} ceramics

Energy Technology Data Exchange (ETDEWEB)

Niewiadomski, Adrian, E-mail: aniewiadomski@us.edu.pl [A. Chelkowski Institute of Physics, University of Silesia, Uniwersytecka 4, 40-007 Katowice (Poland); Kania, Antoni [A. Chelkowski Institute of Physics, University of Silesia, Uniwersytecka 4, 40-007 Katowice (Poland); Kugel, Godefroy E. [LMPOS, University of Metz and Supelec Metz, 2 rue E. Belin, Metz 57070 (France); Hafid, Mustapha [LPGC Dept. of Physics BP 133, Faculty of Science, Ibn Tofail University, 14000 Kenitra (Morocco); Sitko, Dorota [Institute of Physics, Pedagogical University, ul. Podchorazych 2, PL 30-084 Krakow (Poland)

2015-05-15

Highlights: • First Raman scattering studies of Ag{sub 0.96}Li{sub 0.04}NbO{sub 3}, allowed us to correlate temperature evolution of relaxational frequency γ{sub R}(T) with the Nb-ion dynamics and showed its changes at freezing temperature and ferrielectric transition. - Abstract: Silver lithium niobates Ag{sub 1−x}Li{sub x}NbO{sub 3} are promising lead free piezoelectrics. Good quality Ag{sub 0.96}Li{sub 0.04}NbO{sub 3} ceramics were obtained. Dielectric and DSC studies showed that, in comparison to AgNbO{sub 3,} temperatures of phase transitions slightly decrease. Dielectric studies pointed to enhancement of polar properties. Remnant polarisations achieves value of 0.6 μC/cm{sup 2}. Maximum of ϵ(T) dependences related to the relaxor-like ferroelectric/ferrielectric M{sub 1}–M{sub 2} transition becomes higher and more frequency dependent. Analysis of Raman spectra showed that two modes at 50 and 194 cm{sup −1} exhibit significant softening. Low frequency part of the Raman spectra which involve central peak and soft mode were analysed using two models. CP was assumed as relaxational vibration and described by Debye function. The slope of temperature dependences of relaxational frequency γ{sub R}(T) changes at approximately 470 and 330 K, indicating that slowing down process of relaxational vibrations changes in the vicinity of partial freezing of Nb-ion dynamics T{sub f} and further freezing at ferroelectric/ferrielectric phase transition.

Oxidation of Zr and thin (0.2-4 nm) Zr films on Ag: An ESCA investigation

International Nuclear Information System (INIS)

Steiner, P.; Sander, I.; Siegwart, B.; Huefner, S.

1987-01-01

The oxidation of polycrystalline Zr under 10 -8 -10 -3 mbar oxygen pressure in the temperature range 25 0 -350 0 C is obtained from ESCA experiments. Changes in the ESCA spectra for thin Zr films on Ag oxidized at 250 0 C are observed and compared to the bulk Zr-metal. Thin Ag overlayers on Zr show a catalytic increase of the room temperature oxidation of Zr. (orig.)

Differential dissolution of biogenic carbonates: Implications of secretion at higher pH

Digital Repository Service at National Institute of Oceanography (India)

Saraswat, R.

-138. Berger, W.H. 1971. Sedimentation of planktonic foraminifera. Marine Geology 11: 325-358. Burton, E.A. and Walter, L.M. 1991. The effects of pCO 2 and temperature on magnesium incorporation in calcite in seawater and MgCl 2 -CaCl 2 solutions. Geochimica... for house building: Mg 2+ or H + removal? Geochimica Cosmochimica Acta, 66: 1159-1169. Zondervan, I., Zeebe, R., Rost, B. and Riebesell, U. 2001. Decreasing marine biogenic calcification: A negative feedback on rising atmospheric pCO 2 . Global...

Chondrogenic differentiation of ATDC5-cells under the influence of Mg and Mg alloy degradation.

Science.gov (United States)

Martinez Sanchez, Adela H; Feyerabend, Frank; Laipple, Daniel; Willumeit-Römer, Regine; Weinberg, Annelie; Luthringer, Bérengère J C

2017-03-01

Biodegradable magnesium (Mg)-based materials are a potential alternative to permanent implants for application in children. Nevertheless effects of those materials on growth plate cartilage and chondrogenesis have not been previously evaluated. In vitro differentiation of ATDC5 cells was evaluated under the influence of pure Mg (PMg), Mg with 10wt% of gadolinium (Mg-10Gd) and Mg with 2wt% of silver (Mg-2Ag) degradation products (extracts) and direct cell culture on the materials. Gene expression showed an inhibitory effect on ATDC5 mineralization with the three extracts and a chondrogenic potential of Mg-10Gd. Cells cultured in Mg-10Gd and Mg-2Ag extracts showed the same proliferation and morphology than cells cultured in growth conditions. Mg-10Gd induced an increase in production of ECM and a bigger cell size, similar to the effects found with differentiation conditions. An increased metabolic activity was observed in cells cultured under the influence of Mg-10Gd extracts, indicated by an acidic pH during most of the culture period. After 7days of culture on the materials, ATDC5 growth, distribution and ECM synthesis were higher on Mg-10Gd samples, followed by Mg-2Ag and PMg, which was influenced by the homogeneity and composition of the degradation layer. This study confirmed the tolerance of ATDC5 cells to Mg-based materials and a chondrogenic effect of Mg-10Gd. Further studies in vitro and in vivo are necessary to evaluate cell reactions to those materials, as well as the effects on bone growth and the biocompatibility of the alloying system in the body. Copyright © 2016 Elsevier B.V. All rights reserved.

The role of air annealing on the optical and scintillation properties of Mg co-doped Pr:LuAG transparent ceramics

Czech Academy of Sciences Publication Activity Database

Hu, Z.; Cao, M.; Chen, H.; Shi, Y.; Kou, H.; Xie, T.; Wu, L.; Pan, Y.; Feng, X.; Vedda, A.; Beitlerová, Alena; Nikl, Martin; Li, J.

2017-01-01

Roč. 72, Oct (2017), s. 201-207 ISSN 0925-3467 R&D Projects: GA ČR GA16-15569S Institutional support: RVO:68378271 Keywords : Mg co-doped Pr:LuAG * transparent ceramics * annealing effect * luminescence Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 2.238, year: 2016

Steady state creep during metastable phase transition in Al-16 wt% Ag and Al-16 wt% Ag-0.1 wt% Zr alloys

Energy Technology Data Exchange (ETDEWEB)

Deaf, G.H.; Youssef, S.B.; Mahmoud, M.A. [Ain Shams Univ., Cairo (Egypt). Dept. of Physics

1998-08-16

The early stages of decomposition of Guinier-Preston zones (G.P. zones) in Al-16 wt% Ag and Al-16 wt% Ag-0.1 wt% Zr alloys were investigated through creep measurements and electron microscopy observations. It was found that the strengthening and softening of the alloys has been achieved during the formation of metastable phases (G.P. zones and {gamma}`-phase) in the ageing temperature range (428 to 498 K). TEM investigations confirmed that the addition of zirconium to the Al-Ag alloy accelerates the formation and coarsening of the metastable phases. The mean values of activation energy of both alloys were found to be equal to that quoted for precipitate-dislocation interactions. (orig.) 23 refs.

Simultaneous determination of Hg(II)-Ag(I)-Cd(II) by conductometric titration using the formation of ternary complex

International Nuclear Information System (INIS)

Hayashida, Ichiro; Yoshida, Hitoshi; Taga, Mitsuhiko; Hikime, Seiichiro

1979-01-01

A conductometric determination of Hg(II), Ag(I) and Cd(II) was carried out by using the insoluble ternary complex formation of the metal ions with iodide ion in the presence of 1,10-phenanthroline (phen). Recommended procedure is as follows; An aliquot of sample solution containing (14 -- 29) mg of Hg(II), (8 -- 16) mg of Ag(I), and (9 -- 17) mg of Cd(II) transfered into a 100 ml beaker. Add to acetate buffer and stoichiometric amounts of phen (40% ethanol-water solution). Amounts of nitrate ion which was estimated separately by other titration with 0.1 M Ag(phen) 2 complex (40% ethanol-water solution) are adjusted in the range of (4.0 -- 6.0) mM. The sample solution is titrated with 0.1 M KI standard solution at the rate of 0.20 ml/min or less. The titration curve showed three end-points corresponding to the formation of (1) Hg(phen) 2 I 2 , (2) Ag(phen)I, and (3) Cd(phen) 2 I 2 . The relative standard deviation was less than 0.8%, when the pH value was controlled at 4.0 -- 4.5 (acetate buffer) and the nitrate concentration was adjusted in the range of (4.0 -- 6.0)mM. The effect of diverse ions on the determination was also investigated in detail. (author)

Reducing Mg acceptor activation-energy in Al(0.83)Ga(0.17)N disorder alloy substituted by nanoscale (AlN)₅/(GaN)₁ superlattice using Mg(Ga) δ-doping: Mg local-structure effect.

Science.gov (United States)

Zhong, Hong-xia; Shi, Jun-jie; Zhang, Min; Jiang, Xin-he; Huang, Pu; Ding, Yi-min

2014-10-23

Improving p-type doping efficiency in Al-rich AlGaN alloys is a worldwide problem for the realization of AlGaN-based deep ultraviolet optoelectronic devices. In order to solve this problem, we calculate Mg acceptor activation energy and investigate its relationship with Mg local structure in nanoscale (AlN)5/(GaN)1 superlattice (SL), a substitution for Al(0.83)Ga(0.17)N disorder alloy, using first-principles calculations. A universal picture to reduce acceptor activation energy in wide-gap semiconductors is given for the first time. By reducing the volume of the acceptor local structure slightly, its activation energy can be decreased remarkably. Our results show that Mg acceptor activation energy can be reduced significantly from 0.44 eV in Al(0.83)Ga(0.17)N disorder alloy to 0.26 eV, very close to the Mg acceptor activation energy in GaN, and a high hole concentration in the order of 10(19) cm(-3) can be obtained in (AlN)5/(GaN)1 SL by Mg(Ga) δ-doping owing to GaN-monolayer modulation. We thus open up a new way to reduce Mg acceptor activation energy and increase hole concentration in Al-rich AlGaN.

Reducing Mg Acceptor Activation-Energy in Al0.83Ga0.17N Disorder Alloy Substituted by Nanoscale (AlN)5/(GaN)1 Superlattice Using MgGa δ-Doping: Mg Local-Structure Effect

Science.gov (United States)

Zhong, Hong-Xia; Shi, Jun-Jie; Zhang, Min; Jiang, Xin-He; Huang, Pu; Ding, Yi-Min

2014-10-01

Improving p-type doping efficiency in Al-rich AlGaN alloys is a worldwide problem for the realization of AlGaN-based deep ultraviolet optoelectronic devices. In order to solve this problem, we calculate Mg acceptor activation energy and investigate its relationship with Mg local structure in nanoscale (AlN)5/(GaN)1 superlattice (SL), a substitution for Al0.83Ga0.17N disorder alloy, using first-principles calculations. A universal picture to reduce acceptor activation energy in wide-gap semiconductors is given for the first time. By reducing the volume of the acceptor local structure slightly, its activation energy can be decreased remarkably. Our results show that Mg acceptor activation energy can be reduced significantly from 0.44 eV in Al0.83Ga0.17N disorder alloy to 0.26 eV, very close to the Mg acceptor activation energy in GaN, and a high hole concentration in the order of 1019 cm-3 can be obtained in (AlN)5/(GaN)1 SL by MgGa δ-doping owing to GaN-monolayer modulation. We thus open up a new way to reduce Mg acceptor activation energy and increase hole concentration in Al-rich AlGaN.

Bulk amorphous alloys: Preparation and properties of (Mg0.98Al0.02)x(Cu0.75Y0.25)100

DEFF Research Database (Denmark)

Eldrup, Morten Mostgaard; Pedersen, Allan Schrøder; Ohnuma, M.

2000-01-01

New bulk amorphous quaternary alloys of the composition (Mg1-xAlx)(60)Cu30Y10 (x = 0 - 0.17) were recently reported by the authors and preliminary results of the influence of Al content on the ability to form a bulk amorphous phase were presented. In the present note we extend this work to look...... for the influence of the Mg-Al content on the glass forming ability by studying a range of compositions, (Mg0.98Al0.02)(x)(Cu0.75Y0.25)(100-x) for x = 60 - 80 at.%. As previously, the alloys were prepared by a relatively simple technique, i.e. rapid cooling of the melt in a wedge-shaped copper mould. This method...... provides a range of cooling rates within a single ingot during the solidification that link the slowly and rapidly cooled microstructure for each alloy composition. Hence, the maximum thickness of the amorphous part of the cast material will be a measure of the glass forming ability (GFA) of the particular...

Whisker-Like Formations in Sn-3.0Ag-Pb Alloys

Directory of Open Access Journals (Sweden)

Koncz-Horváth D.

2017-06-01

Full Text Available In this study, different types of whisker-like formations of Sn-3.0Ag based alloy were presented. In the experimental process the amount of Pb element was changed between 1000 and 2000 ppm, and the furnace atmosphere and cooling rate were also modified. The novelty of this work was that whisker-like formations in macro scale size were experienced after an exothermic reaction. The whiskers of larger sizes than general provided opportunities to investigate the microstructure and the concentration nearby the whiskers. In addition, the whisker-like formations from Sn-Ag based bulk material did not only consist of pure tin but tin and silver phases. The whisker-like growth appeared in several forms including hillock, spire and nodule shaped formations in accordance with parameters. It was observed that the compound phases were clustered in many cases mainly at hillocks.

Experimental study of the phase equilibria in the Mg–Zn–Ag ternary system at 300 °C

Energy Technology Data Exchange (ETDEWEB)

Wang, Jian, E-mail: jian.wang@polymtl.ca [Center for Research in Computational Thermochemistry (CRCT), Department of Chemical Engineering, École Polytechnique, Montréal, Québec H3C 3A7 (Canada); Zhang, Yi-Nan [Department of Mechanical Engineering, Concordia University, 1455 De Maisonneuve Blvd. West, Montreal, Quebec H3G 1M8 (Canada); Hudon, Pierre; Jung, In-Ho [Department of Mining and Materials Engineering, McGill University, 3610 University Street, Montreal, Quebec H3A 0C5 (Canada); Medraj, Mamoun [Department of Mechanical Engineering, Concordia University, 1455 De Maisonneuve Blvd. West, Montreal, Quebec H3G 1M8 (Canada); Department of Mechanical and Materials Engineering, Masdar Institute, Masdar City, P.O. Box 54224, Abu Dhabi (United Arab Emirates); Chartrand, Patrice [Center for Research in Computational Thermochemistry (CRCT), Department of Chemical Engineering, École Polytechnique, Montréal, Québec H3C 3A7 (Canada)

2015-08-05

Highlights: • The phase equilibria of Mg–Zn–Ag system at 300 °C were determined. • A bcc continuous ternary solid solution forms between MgAg (bcc-B2) and AgZn (bcc-A2) was determined. • The extended solid solubilities of the sub-binary compounds were also determined. - Abstract: The phase equilibria in the Mg–Zn–Ag ternary system at 300 °C were investigated using three diffusion couples and 35 key samples. Scanning electron microscopy (SEM) equipped with energy-dispersive spectroscope (EDS) and X-ray diffraction (XRD) techniques were used for homogeneity ranges and crystal structure determination. Large solid solubility limits, due to substitution among Mg, Zn and Ag atoms in Mg{sub 3}Ag and MgZn{sub 2} phases, were observed in the present work. Solid solubility limits of Ag and Zn in the hcp (Mg) phase were found to be less than 1 at.%. The extended solid solubilities of the Mg{sub 12}Zn{sub 13}, Mg{sub 2}Zn{sub 3}, MgZn{sub 2} (C14), Mg{sub 2}Zn{sub 11}, Ag{sub 5}Zn{sub 8} and hcp (AgZn{sub 3}) sub-binary compounds were also determined in the Mg–Zn–Ag ternary system. In addition, a bcc continuous ternary solid solution forms between MgAg (bcc-B2) and AgZn (bcc-A2) at 300 °C.

Determination of biogenic amines in beer by HPLC with pre-column dansylation and study on its forming regularity%柱前衍生-HPLC法测定啤酒中生物胺及其形成规律研究

Institute of Scientific and Technical Information of China (English)

谷凤霞; 王婷; 李宪臻; 王伟; 郭萍; 俞志敏

2015-01-01

建立了柱前衍生-高效液相色谱(HPLC)法同时检测啤酒中8种生物胺的方法,并研究了啤酒酿造原料、酿造过程及腐败菌的生物胺形成规律.样品经5％三氯乙酸溶液提取后,经丹磺酰氯衍生,然后用HPLC进行定性和定量分析.该方法对8种生物胺具有良好的分离效果,并具有线性范围广,精密度和重复性高等优点,适用于啤酒中生物胺的检测.运用该方法对啤酒酿造原料(麦芽和酒花)中生物胺进行检测,发现除β-苯乙胺外其他7种生物胺均有检出,其中色胺和腐胺含量最高.麦汁和发酵过程中主要含有色胺和腐胺,主要来源于原料麦芽.将2株啤酒腐败乳酸菌-乳酸短杆菌(Lactobacillus brevis)BS49和类布氏乳杆菌(Lactobacillus parabuchneri)B S201接入到无菌啤酒中,分析其生物胺形成规律.这2株菌能在啤酒中生长繁殖,并且随着菌体生长啤酒中生物胺含量发生显著变化,接BS49号菌的啤酒中酪胺由0.2 mg/L增加到8 mg/L,接BS201号菌的啤酒中组胺由0.1 mg/L增加到6 mg/L,因此组胺和酪胺可作为判断啤酒在贮藏过程中是否污染乳酸菌的重要指标.%An analytical method for simultaneous determination of 8 biogenic amines in beer by high-performance liquid chromatography (HPLC) has been developed, meanwhile the forming regularity of biogenic amines in brewing material, brewing process and beer spoilage bacteria was studied.After being extracted with 5％ TCA and derived with dansyl chloride, biogenic amines in beer were qualitatively and quantitatively analyzed by HPLC.The method of HPLC was conformed with efficient separation, good reproducibility, high sensitivity and wide linear range, which was conducive to analysis of biogenic amines in beer.The established method has been successfully applied to determine biogenic amines in malt and hop.The results showed that the 8 biogenic amines were all detected except β-phenylethyl-amine, and the contents of

Performance of Mg-14Li-1Al-0.1Ce as anode for Mg-air battery

Energy Technology Data Exchange (ETDEWEB)

Ma, Yibin; Li, Deyu [School of Chemical Engineering and Technology, Harbin Institute of Technology, West Street No. 92, Harbin 150001 (China); Li, Ning [School of Chemical Engineering and Technology, Harbin Institute of Technology, West Street No. 92, Harbin 150001 (China); Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin Engineering University, Harbin 150001 (China); Zhang, Milin; Huang, Xiaomei [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin Engineering University, Harbin 150001 (China)

2011-02-15

In this research, a new Mg-air battery based on Mg-14Li-1Al-0.1Ce was prepared and the battery performance was investigated by constant current discharge test. The corrosion behavior of Mg, AZ31 and Mg-Li-Al-Ce were studied by self-corrosion rate measurement and potentiodynamic polarization measurement. The characteristics of Mg-Li-Al-Ce after discharge were investigated by electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results show that Mg-Li-Al-Ce is more active than Mg and AZ31. The self-corrosion rate is found to be in the order: Mg-Li-Al-Ce < Mg < AZ31. It has been observed that the Mg-air battery based on Mg-Li-Al-Ce offers higher operating voltage, anodic efficiency and capacity than those with Mg and AZ31. SEM and EIS results show that the discharge product of Mg-Li-Al-Ce is loosely adhered to the alloy surface, and thus Mg-Li-Al-Ce could keep high discharge activity during discharge. (author)

Preparation and characterization of Ag-added Bi1⋅84Pb0 ...

Indian Academy of Sciences (India)

Unknown

microscopy (SEM), electrical transport and a.c. susceptibility techniques. The tube ... high current conductor is high Jc. However, non-textured, porous structure with ... contact resistance studies on Ag added (0–25 wt%) Bi-. 2223 bulk tubes ...

Hydrothermal, biogenic, and seawater components in metalliferous black shales of the Brooks Range, Alaska: Synsedimentary metal enrichment in a carbonate ramp setting

Science.gov (United States)

Slack, John F.; Selby, David; Dumoulin, Julie A.

2015-01-01

Trace element and Os isotope data for Lisburne Group metalliferous black shales of Middle Mississippian (early Chesterian) age in the Brooks Range of northern Alaska suggest that metals were sourced chiefly from local seawater (including biogenic detritus) but also from externally derived hydrothermal fluids. These black shales are interbedded with phosphorites and limestones in sequences 3 to 35 m thick; deposition occurred mainly on a carbonate ramp during intermittent upwelling under varying redox conditions, from suboxic to anoxic to sulfidic. Deposition of the black shales at ~335 Ma was broadly contemporaneous with sulfide mineralization in the Red Dog and Drenchwater Zn-Pb-Ag deposits, which formed in a distal marginal basin.Relative to the composition of average black shale, the metalliferous black shales (n = 29) display large average enrichment factors (>10) for Zn (10.1), Cd (11.0), and Ag (20.1). Small enrichments (>2–seawater. Such moderate enrichments, which are common in other metalliferous black shales, suggest wholly marine sources (seawater and biogenic material) for these metals, given similar trends for enrichment factors in organic-rich sediments of modern upwelling zones on the Namibian, Peruvian, and Chilean shelves. The largest enrichment factors for Zn and Ag are much higher (1.4 × 107 and 2.9 × 107, respectively), consistent with an appreciable hydrothermal component. Other metals such as Cu, Pb, and Tl that are concentrated in several black shale samples, and are locally abundant in the Red Dog and Drenchwater Zn-Pb-Ag deposits, may have a partly hydrothermal origin but this cannot be fully established with the available data. Enrichments in Cr (up to 7.8 × 106) are attributed to marine and not hydrothermal processes. The presence in some samples of large enrichments in Eu (up to 6.1 × 107) relative to modern seawater and of small positive Eu anomalies (Eu/Eu* up to 1.12) are considered unrelated to hydrothermal activity, instead

Biogenic synthesis and spatial distribution of silver nanoparticles in the legume mungbean plant (Vigna radiata L.).

Science.gov (United States)

Kumari, Rima; Singh, Jay Shankar; Singh, Devendra Pratap

2017-01-01

The present investigation aimed to study the in vivo synthesis of silver nanoparticles (AgNPs) in the legume Vigna radiata. The level of plant metabolites such as total phenolics, lipid, terpenoids, alkaloids and amino acid increased by 65%, 133%, 19%, 67% and 35%, respectively, in AgNO 3 (100 mg L -1 ) treated plants compared to control. Whereas protein and sugar contents in the treated plants were reduced by 38% and 27%, respectively. FTIR analysis of AgNO 3 (20-100 mg L -1 ) treated plants exhibited changes in the IR regions between 3297 and 3363 cm -1 , 1635-1619 cm -1 , 1249-1266 cm -1 and that corresponded to alterations in OH groups of carbohydrates, OH and NH groups of amide I and II regions of protein, when compared with the control. Transmission electron micrographs showed the spatial distribution of AgNPs in the chloroplast, cytoplasmic spaces, vacuolar and nucleolar plant regions. Metal quantification in different tissues of plants exposed to 20-100 mg L -1 AgNO 3 showed about a 22 fold accumulation of Ag in roots as compared to shoots. The phytotoxic parameters such as percent seed germination and shoot elongation remained almost unaltered at low AgNO 3 doses (20-50 mg L -1 ). However, at higher levels of exposure (100 mg L -1 ), the percent seed germination as well as root and shoot elongation exhibited concentration dependent decline. In conclusion, synthesis of AgNPs in V. radiata particularly at lower doses of AgNO 3 , could be used as a sustainable and environmentally safe technology for large scale production of metal nanoparticles. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

A novel green synthesis of Fe{sub 3}O{sub 4}-Ag core shell recyclable nanoparticles using Vitis vinifera stem extract and its enhanced antibacterial performance

Energy Technology Data Exchange (ETDEWEB)

Venkateswarlu, Sada; Natesh Kumar, B.; Prathima, B. [Analytical and inorganic Division of Chemistry, S.V. University, Tirupati-517502, Andhra Pradesh (India); Anitha, K. [Department of Chemistry, S.K. University, Anantapur-515003, Andhra Pradesh (India); Jyothi, N.V.V., E-mail: nvvjyothi01@gmail.com [Analytical and inorganic Division of Chemistry, S.V. University, Tirupati-517502, Andhra Pradesh (India)

2015-01-15

We described a novel and eco-friendly method for preparing Fe{sub 3}O{sub 4}-Ag core shell nanoparticles (CSNPs) with high magnetism and potent antibacterial activity. The Fe{sub 3}O{sub 4}-Ag CSNPs were obtained using waste material of Vitis vinifera (grape) stem extract as the green solvent, reducing and capping agent. The result recorded from X-ray powder diffraction (XRD), UV–vis spectrum, energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FT-IR) supports the biosynthesis and characterization of Fe{sub 3}O{sub 4}-Ag CSNPs. From transmission electron microscopy (TEM) the size of the Fe{sub 3}O{sub 4}-Ag nanoparticles was measured below 50 nm; high-resolution TEM (HRTEM) indicates the core shell structure; and selected area electron diffraction (SAED) has revealed polycrystalline nature. Vibrating sample magnetometer (VSM) shows the ferromagnetic nature of Fe{sub 3}O{sub 4}-Ag CSNPs at room temperature with saturation magnetization of 15.74 emu/g. Further, these biogenic nanoparticles were highly hazardous to microorganisms. The antibacterial activity of biogenic Fe{sub 3}O{sub 4}-Ag CSNPs showed potent inhibitory activity against both Gram-positive and Gram-negative pathogens. These nanoparticles may also be reusable because of its excellent ferromagnetic property.

Speleothem Mg-isotope time-series data from different climate belts

Science.gov (United States)

Riechelmann, S.; Buhl, D.; Richter, D. K.; Schröder-Ritzrau, A.; Riechelmann, D. F. C.; Niedermayr, A.; Vonhof, H. B.; Wassenburg, J.; Immenhauser, A.

2012-04-01

Speleothem Mg-isotope time-series data from different climate belts Sylvia Riechelmann (1), Dieter Buhl(1), Detlev K. Richter (1), Andrea Schröder-Ritzrau (2), Dana F.C. Riechelmann (3), Andrea Niedermayr (1), Hubert B. Vonhof (4) , Jasper Wassenburg (1), Adrian Immenhauser (1) (1) Ruhr-University Bochum, Institute for Geology, Mineralogy and Geophysics, Universitätsstraße 150, D-44801 Bochum, Germany (2) Heidelberg Academy of Sciences, Im Neuenheimer Feld 229, D-69120 Heidelberg, Germany (3) Johannes Gutenberg-University Mainz, Institute of Geography, Johann-Joachim-Becher-Weg 21, D-55128 Mainz, Germany (4) Faculty of Earth and Life Sciences, Vrije Universiteit Amsterdam, De Boelelaan 1085, 1081 HV, Amsterdam, The Netherlands The Magnesium isotope proxy in Earth surface research is still underexplored. Recently, field and laboratory experiments have shed light on the complex suite of processes affecting Mg isotope fractionation in continental weathering systems. Magnesium-isotope fractionation in speleothems depends on a series of factors including biogenic activity and composition of soils, mineralogy of hostrock, changes in silicate versus carbonate weathering ratios, water residence time in the soil and hostrock and disequilibrium factors such as the precipitation rate of calcite in speleothems. Furthermore, the silicate (here mainly Mg-bearing clays) versus carbonate weathering ratio depends on air temperature and rainfall amount, also influencing the soil biogenic activity. It must be emphasized that carbonate weathering is generally dominant, but under increasingly warm and more arid climate conditions, silicate weathering rates increase and release 26Mg-enriched isotopes to the soil water. Furthermore, as shown in laboratory experiments, increasing calcite precipitation rates lead to elevated delta26Mg ratios and vice versa. Here, data from six stalagmite time-series Mg-isotope records (Thermo Fisher Scientific Neptune MC-ICP-MS) are shown. Stalagmites

The Effects of Antimony Addition on the Microstructural, Mechanical, and Thermal Properties of Sn-3.0Ag-0.5Cu Solder Alloy

Science.gov (United States)

Sungkhaphaitoon, Phairote; Plookphol, Thawatchai

2018-02-01

In this study, we investigated the effects produced by the addition of antimony (Sb) to Sn-3.0Ag-0.5Cu-based solder alloys. Our focus was the alloys' microstructural, mechanical, and thermal properties. We evaluated the effects by means of scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), differential scanning calorimetry (DSC), and a universal testing machine (UTM). The results showed that a part of the Sb was dissolved in the Sn matrix phase, and the remaining one participated in the formation of intermetallic compounds (IMCs) of Ag3(Sn,Sb) and Cu6(Sn,Sb)5. In the alloy containing the highest wt pct Sb, the added component resulted in the formation of SnSb compound and small particle pinning of Ag3(Sn,Sb) along the grain boundary of the IMCs. Our tests of the Sn-3.0Ag-0.5Cu solder alloys' mechanical properties showed that the effects produced by the addition of Sb varied as a function of the wt pct Sb content. The ultimate tensile strength (UTS) increased from 29.21 to a maximum value of 40.44 MPa, but the pct elongation (pct EL) decreased from 48.0 to a minimum 25.43 pct. Principally, the alloys containing Sb had higher UTS and lower pct EL than Sb-free solder alloys due to the strengthening effects of solid solution and second-phase dispersion. Thermal analysis showed that the alloys containing Sb had a slightly higher melting point and that the addition amount ranging from 0.5 to 3.0 wt pct Sb did not significantly change the solidus and liquidus temperatures compared with the Sb-free solder alloys. Thus, the optimal concentration of Sb in the alloys was 3.0 wt pct because the microstructure and the ultimate tensile strength of the SAC305 solder alloys were improved.

Extraction and determination of biogenic amines in fermented sausages and other meat products using reversed-phase-HPLC.

Science.gov (United States)

Straub, B; Schollenberger, M; Kicherer, M; Luckas, B; Hammes, W P

1993-09-01

A convenient method is described for the analysis of biogenic amines (BA) by means of reversed-phase-HPLC. The method is characterized by multi-channel UV detection (diodearray), subsequent post-column derivatization with o-phthaldialdehyde and 3-mercaptopropionic acid, and fluorescence detection. For the analysis of meat products and especially fermented sausages an optimized perchloric acid extraction process was introduced to determine putrescine, cadaverine, histamine, tyramine and 2-phenylethylamine. BA recoveries from meat ranged between 96 and 113% with a detection limit for amines of 0.5 mg/kg.

Microstructural and Mechanical Characterization of Al-0.80Mg-0.85Si-0.3Zr Alloy

Directory of Open Access Journals (Sweden)

Kahrıman F.

2017-12-01

Full Text Available In this study, Al-0.80Mg-0.85Si alloy was modified with the addition of 0.3 wt.-% zirconium and the variation of microstructural features and mechanical properties were investigated. In order to produce the billets, vertical direct chill casting method was used and billets were homogenized at 580 °C for 6 h. Homogenized billets were subjected to aging practice following three stages: (i solution annealing at 550 °C for 3 h, (ii quenching in water, (iii aging at 180 °C between 0 and 20 h. The hardness measurements were performed for the alloys following the aging process. It was observed that peak hardness value of Al-0.80Mg-0.85Si alloy increased with the addition of zirconium. This finding was very useful to obtain aging parameters for the extruded hollow profiles which are commonly used in automotive industry. Standard tensile tests were applied to aged profiles at room temperature and the results showed that modified alloy had higher mechanical properties compared to the non-modified alloy.

Structure and properties during aging of an ultra-high strength Al-Cu-Li-Ag-Mg alloy

Science.gov (United States)

Gayle, Frank W.; Heubaum, Frank H.; Pickens, Joseph R.

1990-01-01

The structure and properties of the strengthening phases formed during aging in an Al-Cu-Li-Ag-Mg alloy (Weldalite 049) were elulcidated, by following the development of the microstructure by means of TEM. The results of observations showed that the Weldalite 049 alloy has a series of unusual and technologically useful combinations of mechanical properties in different aging conditions, such as natural aging without prior cold work to produce high strengths, a reversion temper of lower yield strength and unusually high ductility, a room temperature reaging of the reversion temper eventually leading to the original T4 hardness, and ultrahigh-strength T6 properties.

Preparation, characterization and antimicrobial efficiency of Ag/PDDA-diatomite nanocomposite.

Science.gov (United States)

Panáček, Aleš; Balzerová, Anna; Prucek, Robert; Ranc, Václav; Večeřová, Renata; Husičková, Vendula; Pechoušek, Jiří; Filip, Jan; Zbořil, Radek; Kvítek, Libor

2013-10-01

Nanocomposites consisting of diatomaceous earth particles and silver nanoparticles (silver NPs) with high antimicrobial activity were prepared and characterized. For the purpose of nanocomposite preparation, silver NPs with an average size of 28nm prepared by modified Tollens process were used. Nanocomposites were prepared using poly(diallyldimethylammonium) chloride (PDDA) as an interlayer substance between diatomite and silver NPs which enables to change diatomite original negative surface charge to positive one. Due to strong electrostatic interactions between negatively charged silver NPs and positively charged PDDA-modified diatomite, Ag/PDDA-diatomite nanocomposites with a high content of silver (as high as 46.6mgAg/1g of diatomite) were prepared. Because of minimal release of silver NPs from prepared nanocomposites to aqueous media (<0.3mg Ag/1g of nanocomposite), the developed nanocomposites are regarded as a potential useful antimicrobial material with a long-term efficiency showing no risk to human health or environment. All the prepared nanocomposites exhibit a high bactericidal activity against Gram-negative and Gram-positive bacteria and fungicidal activity against yeasts at very low concentrations as low as 0.11g/L, corresponding to silver concentration of 5mg/L. Hence, the prepared nanocomposites constitute a promising candidate suitable for the microbial water treatment in environmental applications. Copyright © 2013 Elsevier B.V. All rights reserved.

Biogenic synthesis of Ag-Au-In decorated on rGO nanosheet and its antioxidant and biological activities

Science.gov (United States)

Hazarika, Moushumi; Sonowal, Shashanka; Saikia, Indranirekha; Boruah, Purna K.; Das, Manash R.; Tamuly, Chandan

2017-09-01

Au-Ag-In-rGO nanocomposite was synthesized using fruit extract of Zanthoxylum rhetsa which is an eco-friendly, simple and green method. It was characterized by UV-visible, FT-IR, XRD, XPS, EDX, TEM technique. The antioxidant capacity of the nanocomposite was evaluated in presence of AgNO3, HAuCl4 and InCl3 solution respectively at 25 °C. The results showed significant antioxidant activity in presence of 1  ×  10-5 mM AgNO3 solution. The antibacterial activity of Au-Ag-In-rGO nanoparticles was carried out against the gram  -ve bacteria Pseudomonas aeruginosa, Escherichia coli and gram  +ve bacteria Staphylococcus aureus and Bacillus cereus. The bacterial growth kinetics was studied. The bacterial strain E. coli and S. aureus showed complete inhibition at concentration 100 µg ml-1. The activity is more effective in case of Au-Ag-In-rGO compared to GO.

Synthesize and electrochemical characterization of Mg-doped Li-rich layered Li[Li0.2Ni0.2Mn0.6]O2 cathode material

International Nuclear Information System (INIS)

Wang, Dan; Huang, Yan; Huo, Zhenqing; Chen, Li

2013-01-01

Highlights: • Layered Li[Li 0.2 Ni 0.2−x Mn 0.6−x Mg 2x ]O 2 (2x = 0, 0.01, 0.02, 0.05) were synthetized. • Li[Li 0.2 Ni 0.2−x Mn 0.6−x Mg 2x ]O 2 exhibit enhanced electrochemical properties. • The improved performance is attributed to enhanced structure stability. -- Abstract: Mg-doped Li[Li 0.2 Ni 0.2 Mn 0.6 ]O 2 as a Li-rich cathode material of lithium-ion batteries were prepared by co-precipitation method and ball-milling treatment using Mg(OH) 2 as a dopant. Scanning electron microscopy (SEM), ex situ X-ray powder diffraction (XRD), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvantatic charge/discharge were used to investigate the effect of Mg doping on structure and electrochemical performance. Compared with the bare material, Mg-doped materials exhibit better cycle stabilities and superior rate capabilities. Li[Li 0.2 Ni 0.195 Mn 0.595 Mg 0.01 ]O 2 displays a high reversible capacity of 226.5 mAh g −1 after 60 cycles at 0.1 C. The excellent cycle performance can be attributed to the improvement in structure stability, which is verified by XRD tests before and after 60 cycles. EIS results show that Mg doping decreases the charge-transfer resistance and enhances the reaction kinetics, which is considered to be the major factor for higher rate performance

Thermodynamic properties of solid solutions in the system Ag2S–Ag2Se

International Nuclear Information System (INIS)

Pal’yanova, G.A.; Chudnenko, K.V.; Zhuravkova, T.V.

2014-01-01

We have summarized experimental data on the phase diagram of the system Ag 2 S–Ag 2 Se. Standard thermodynamic functions of four solid solutions in this system have been calculated using the model of regular and subregular solutions: a restricted fcc solid solution γ-Ag 2 S-Ag 2 S 1−x Se x (x 2 S–Ag 2 Se, monoclinic solid solution (α) from Ag 2 S to Ag 2 S 0.4 Se 0.6 , and orthorhombic solid solution (α) from Ag 2 S 0.3 Se 0.7 to the Ag 2 Se. G mix and S mix have been evaluated using the subregular model for asymmetric solution for the region Ag 2 S 0.4 Se 0.6 –Ag 2 S 0.3 Se 0.7 . The thermodynamic data can be used for modeling in complex natural systems and in matters of semiconductor materials

XPS study on Mg0.9-xTi0.1PdxNi (x = 0.04, 0.06, 0.08, 0.1) hydrogen storage electrode alloys after charge-discharge cycles

International Nuclear Information System (INIS)

Tian Qifeng; Zhang Yao; Wu Yuanxin

2009-01-01

The passive film composition of Mg 0.9-x Ti 0.1 Pd x Ni (x = 0.04, 0.06, 0.08, 0.1) hydrogen storage alloys after 40 charge-discharge cycles has been investigated by means of X-ray photoelectron spectroscopy (XPS) in combination with Ar + sputtering technology. With the XPSPEAK software, high resolution spectra of alloy elements and oxygen were deconvolved into individual peaks. Composites formed by metal elements and their relative contents were also deduced. It was found that the composites originated from Mg and Ni were mainly in the form of their oxides and hydroxides, which existed at the top surface of alloys. With the increase of sputtering depth, the hydroxides of Mg and Ni gradually disappeared while corresponding oxides dominated their passive products. According to the analysis results of oxygen spectra, the elemental segregation of Mg and Ni was influenced by the substitution of Pd because the addition of Pd slightly enhanced the surface energy of the alloys and suppressed the formation of Mg hydroxide and oxide. Ti and Pd presented multiple-oxides from the surface to the inner alloys and metallic Pd appeared in the sub-layers of the alloys' surface. The possible mechanisms of the formation of passive products were suggested on the basis of the discussion in the paper.

Pharmacokinetics of hederacoside C, an active ingredient in AG NPP709, in rats.

Science.gov (United States)

Kim, Ju Myung; Yoon, Ji Na; Jung, Ji Won; Choi, Hye Duck; Shin, Young June; Han, Chang Kyun; Lee, Hye Suk; Kang, Hee Eun

2013-11-01

1. Hederacoside C (HDC) is one of the active ingredients in Hedera helix leaf extract (Ivy Ex.) and AG NPP709, a new botanical drug to treat acute respiratory infection and chronic inflammatory bronchitis. However, information regarding its pharmacokinetic properties remains limited. 2. Here, we report the pharmacokinetics of HDC in rats after intravenous administration of HDC (3, 12.5, and 25 mg/kg) and after oral administration of HDC, Ivy Ex., and AG NPP709 (equivalent to 12.5, 25, and 50 mg/kg HDC). 3. Linear pharmacokinetics of HDC were identified upon its intravenous administration at doses of 3-25 mg/kg. Intravenous administration of HDC results in relatively slow clearance (1.46-2.08 mL/min/kg) and a small volume of distribution at steady state (138-222 mL/kg), while oral administration results in a low absolute oral bioavailability (F) of 0.118-0.250%. The extremely low F of HDC may be due to poor absorption of HDC from the gastrointestinal (GI) tract and/or its decomposition therein. 4. The oral pharmacokinetics of HDC did not differ significantly among pure HDC, Ivy Ex., and AG NPP709.

Influence of ripening time on the amount of certain biogenic amines in rind and core of cow milk Livno cheese

Directory of Open Access Journals (Sweden)

Antonela Marijan

2014-09-01

Full Text Available Determining the levels of biogenic amines in cheese except that it has significance for determining the nutritional value and hygienic accuracy, cheese as food can be used as a parameter to evaluate the conditions of production and/or ripening of products, and particularly in the selection of bacterial cultures. The purpose of this paper was to determine the effect of the ripening process on the amount of biogenic amines in cheese. For this purpose were conducted physico-chemical analysis, determination of biogenic amines and microbiological analysis. During the process of ripening Livno cheese from three different batches was taken one cheese from prime day and 9th, 20th, 29th, 50th, 60th and 105th day. From each cheese two samples were taken, one from the middle and one from the cheese rind. During 105th day of ripening Livno cheese, the presence of triptamin, ß-feniletlamine, putrescine, cadaverine, histamine, tyramine, spermine and spermidine were determinated. The maximum total values of searched biogenic amines were found 105th day, in the middle 184.13 mg/kg and 76.26 mg/kg in the rind of cheese. With an indication that the largest share of value rep¬resent histamine with 43.9 % and tyramine with 38.2 % in the middle, respectively histamine with 31.6 % and tyramine with 31.5 % in the rind of cheese. The values of putrescine and spermine were in small ranges and they are not identified in all samples. The values of histamine and tyramine are almost a third more at 105th than 60th day. There was a significant difference between the middle and the rind of cheese in the values of biogenic amines. Correlation between biogenic amines and microorganisms has not been determined.

Influence of Mg{sup 2+} doping on the structure and electrochemical performances of layered LiNi{sub 0.6}Co{sub 0.2-x}Mn{sub 0.2}Mg{sub x}O{sub 2} cathode materials

Energy Technology Data Exchange (ETDEWEB)

Huang, Zhenjun; Wang, Zhixing, E-mail: zxwang.csu@hotmail.com; Guo, Huajun; Li, Xinhai

2016-06-25

Introducing the Mg ion into host lattice is applied to improving the electrochemical performance of LiNi{sub 0.6}Co{sub 0.2}Mn{sub 0.2}O{sub 2}. The effect of Mg substitution for Co on the structure, morphology, electrochemical properties and Li{sup +} diffusion coefficients are investigated in details. Rietveld refinement results reveal that Mg is incorporated into the bulk lattice, which results in reduced cation mixing and expand c-lattice parameter. All Mg-doped sample exhibit better cycle and rate performances, although the Mg substitution for Co led to decreasing a part of capacity. The Li diffusion coefficients obtained by galvanostatic intermittent titration technique (GITT) are increased with increases of Mg content. - Highlights: • Mg-doped sample exhibits better electrochemical performance. • The change of crystal structure by Mg doping are studied. • The Mg doping improves the lithium ion diffusion coefficient.

Precipitation kinetics of Al-1.12 Mg{sub 2}Si-0.35 Si and Al-1.07 Mg{sub 2}Si-0.33 Cu alloys

Energy Technology Data Exchange (ETDEWEB)

Gaber, A. [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt); Gaffar, M.A. [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt)]. E-mail: mgaafar@aucegypt.edu; Mostafa, M.S. [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt); Zeid, E.F. Abo [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt)

2007-02-21

The kinetics of hardening precipitates of Al-1.12 wt.% Mg{sub 2}Si-0.35 wt.% Si (excess Si) and Al-1.07 wt.% Mg{sub 2}Si-0.33 wt.% Cu (balanced + Cu) alloys have been investigated by means of differential scanning calorimetry and hardness measurements. The excess Si enhances the precipitation kinetics and improves the strength of the material. On the other hand, however addition of Cu assist formation of the Q' phase which positively changed the alloy strength. The high binding energy between vacancies and solute atoms (Si and Mg) enhances the combination of Si, Mg and vacancies to form Si-Mg-vacancy clusters. These clusters act as nucleation sites for GP-zones. The coexistence of the {beta}'- and Q'-precipitates in the balanced + Cu alloy results in a higher peak age hardening compared to the alloy with Si in excess.

Photoreduction of Ag{sup +} in Ag/Ag{sub 2}S/Au memristor

Energy Technology Data Exchange (ETDEWEB)

Mou, N.I.; Tabib-Azar, M., E-mail: azar.m@utah.edu

2015-06-15

Highlights: • The effect of illumination on the operating voltages and switching speed of Ag/Ag{sub 2}S/Au memristors is studied • Illumination decreased the average switching time from high to low resistance states by ∼19% and decreased the turn-off voltages dramatically from −0.8 V to −0.25 V. • Photo-induced reduction of silver in Ag{sub 2}S may be used in three dimensional optical memories that can be electronically read and reset. • Illumination changed sulfur's valency and modified its oxidation/reduction potential. - Abstract: Silver halides and chalcogenides are excellent memristor materials that have been extensively used in the past as photosensitive layers in photography. Here we examine the effect of illumination on the operating voltages and switching speed of Ag/Ag{sub 2}S/Au memristors using a green laser (473–523 nm). Our results indicate that illumination decreases the average switching time from high to low resistance states by ∼19% and decreases the turn-off voltages dramatically from −0.8 V to −0.25 V that we attribute to the change in sulfur valency and a photo-induced change in its oxidation/reduction potential. Photo-induced reduction of silver in Ag{sub 2}S may be used in three dimensional optical memories that can be electronically read and reset.

Three-dimensional Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O heterostructures for improving photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

He, Xiaoyu [Department of Applied Physics, Chongqing University, Chongqing 400044 (China); Department of Physics and Electronic Engineering, Yangtze Normal University, Chongqing 408100 (China); Hu, Chenguo, E-mail: hucg@cqu.edu.cn [Department of Applied Physics, Chongqing University, Chongqing 400044 (China); Xi, Yi; Zhang, Kaiyou; Hua, Hao [Department of Applied Physics, Chongqing University, Chongqing 400044 (China)

2014-02-01

Highlights: • Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O 3D network heterostructures are prepared via a simple precipitatation method. • Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O networks exhibit much enhanced photocatalytic activity. • High photocatalytic activity is attributed to its heterostructure and 3D architectures. - Abstract: Three-dimensional Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O heterostructures were fabricated by loading Ag{sub 2}O nanoparticles on WO{sub 3}·0.33H{sub 2}O 3D networks via a simple chemical precipitation method. The Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O heterostructures exhibited much enhanced photocatalytic activity for the degradation of methylene blue (MB) under simulated solar light irradiation. The optimal molar ratio of Ag{sub 2}O and WO{sub 3}·0.33H{sub 2}O is 1:2. The outstanding photocatalytic activity of the Ag{sub 2}O/WO{sub 3}·0.33H{sub 2}O can be attributed to its large surface area of the three-dimensional networks, the enhanced sunlight absorption and the prevention of electrons–holes combination from the heterostructures. The experiment result demonstrates that wide band gap semiconductor (WO{sub 3}·0.33H{sub 2}O) modified by narrow band gap metal oxide (Ag{sub 2}O) with 3D architecture will be an effective route to enhance its photocatalytic activity.

Modification of energy band alignment and electric properties of Pt/Ba{sub 0.6}Sr{sub 0.4}TiO{sub 3}/Pt thin-film ferroelectric varactors by Ag impurities at interfaces

Energy Technology Data Exchange (ETDEWEB)

Hirsch, S.; Komissinskiy, P., E-mail: komissinskiy@oxide.tu-darmstadt.de; Flege, S.; Li, S.; Rachut, K.; Klein, A.; Alff, L. [Institute of Materials Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany)

2014-06-28

We report on the effects of Ag impurities at interfaces of parallel-plate Pt/Ba{sub 0.6}Sr{sub 0.4}TiO{sub 3}/Pt thin film ferroelectric varactors. Ag impurities occur at the interfaces due to diffusion of Ag from colloidal silver paint used to attach the varactor samples with their back side to the plate heated at 600–750 °C during deposition of Ba{sub 0.6}Sr{sub 0.4}TiO{sub 3}. X-ray photoelectron spectroscopy and secondary ion mass spectrometry suggest that amount and distribution of Ag adsorbed at the interfaces depend strongly on the adsorbent surface layer. In particular, Ag preferentially accumulates on top of the Pt bottom electrode. The presence of Ag significantly reduces the barrier height between Pt and Ba{sub 0.6}Sr{sub 0.4}TiO{sub 3} leading to an increased leakage current density and, thus, to a severe degradation of the varactor performance.

Electrochemical corrosion behaviour of lead-free Sn-8.5 Zn-X Ag-0.1 Al-0.5 Ga solder in 3.5% NaCl solution

International Nuclear Information System (INIS)

Mohanty, Udit Surya; Lin, K.-L.

2005-01-01

The electrochemical corrosion behaviour of Pb-free Sn-8.5 Zn-X Ag-0.1 Al-0.5 Ga solder in 3.5% NaCl solution was investigated by using potentiodynamic polarization methods, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and X-ray photoelectron spectroscopy (XPS) analysis. The results obtained from polarization studies showed that an increase in the Ag content from 0.1 to 1.5 wt% decreased the corrosion current density (I corr ) and shifted the corrosion potential (E corr ) towards more noble values. These changes were also reflected in the linear polarization resistance (LPR), corrosion rate, anodic Tafel slope (b A ) and the cathodic Tafel slope (b c ) values, respectively. Passivation behaviour was noted in the Sn-Zn-X Ag-Al-Ga solders with Ag content > 0.1 wt%. The oxides and hydroxides of zinc were responsible for the formation of passive film. Presence of Ag atoms in the oxide layer also improved the passivation behaviour of solders to a certain extent. X-ray photoelectron spectroscopy revealed that two different oxygen species were formed on the surface films, one was assigned to OH - in Zn(OH) 2 and the other to O 2 - in ZnO. XPS depth profile results revealed that the two species had different depth distribution in the films. SEM and EDX analyses confirmed SnCl 2 as the major corrosion product formed after the electrochemical experiments

Impact of Mg content on native point defects in Mg{sub x}Zn{sub 1−x}O (0 ≤ x ≤ 0.56)

Energy Technology Data Exchange (ETDEWEB)

Perkins, J.; Foster, G. M. [Department of Physics, The Ohio State University, 191 West Woodruff Ave., Columbus, Ohio 43210 (United States); Myer, M.; Mehra, S. [Columbus School for Girls, 56 S. Columbia Ave., Columbus, Ohio 43209 (United States); Chauveau, J. M. [Centre de Recherche sur l’Hetero-Epitaxie et ses Applications, Centre National de la Recherche Scientifique (CRHEA-CNRS), Rue B. Gregory, F-06560 Valbonne Sophia Antipolis (France); University of Nice Sophia Antipolis, Parc Valrose, F-06102 Nice Cedex 2 (France); Hierro, A. [Dpto. Ingeniería Electrónica and ISOM, Universidad Politécnica de Madrid, Ciudad Universitaria s/n, 28040 Madrid (Spain); Redondo-Cubero, A. [Dpto. Física Aplicada y Centro de Micro-Análisis de Materiales, Universidad Autónoma de Madrid, 28049 Madrid (Spain); Windl, W. [Department of Materials Science and Engineering, The Ohio State University, 2041 College Road N., Columbus, Ohio 43210 (United States); Brillson, L. J., E-mail: brillson.1@osu.edu [Department of Physics, The Ohio State University, 191 West Woodruff Ave., Columbus, Ohio 43210 (United States); Department of Electrical and Computer Engineering, The Ohio State University, 2015 Neil Avenue, Columbus, Ohio 43210-1272 (United States); Center for Materials Research, The Ohio State University, Columbus, Ohio 43210 (United States)

2015-06-01

We used depth-resolved cathodoluminescence spectroscopy and surface photovoltage spectroscopy to measure the densities, energy levels, and spatial distributions of zinc/magnesium cation and oxygen vacancies in isostructural, single-phase, non-polar Mg{sub x}Zn{sub 1−x}O alloys over a wide (0 ≤ x ≤ 0.56) range. Within this wide range, both defect types exhibit strong Mg content-dependent surface segregation and pronounced bulk density minima corresponding to unit cell volume minima, which can inhibit defect formation due to electrostatic repulsion. Mg in ZnO significantly reduces native defect densities and their non-polar surface segregation, both major factors in carrier transport and doping of these oxide semiconductors.

Geometric Effects of La1+xMg2-xNi9 (x=0.0～1.0) Ternary Alloys on Their Hydrogen Storage Capacities

Institute of Scientific and Technical Information of China (English)

Zhiqing YUAN; Guanglie LU; Bin LIAO; Yongquan LEI

2005-01-01

Structural analysis was made using X-ray diffraction (XRD) Rietveld refinement on a series of La1+xMg2-xNi9(x=0.0～1.0) ternary alloys. Results showed that each of La1+xMg2-xNi9 alloys was a PuNi3-type structure stacked by LaNi5 and (La, Mg) Ni2 blocks. Electrochemical tests revealed that discharge abilities of these La-Mg-Ni ternary alloys mainly depended on their atomic distances between (La, Mg) and Ni, which could be modified by varying the atomic ratios of La/Mg.

Study of Cs adsorption on Ga(Mg)0.75Al0.25N (0 0 0 1) surface: A first principle calculation

International Nuclear Information System (INIS)

Yang, Mingzhu; Chang, Benkang; Hao, Guanghui; Guo, Jing; Wang, Honggang; Wang, Meishan

2013-01-01

In order to study the activation process of Ga 1−x Al x N photocathodes theoretically, models of Cs adsorption on Ga(Mg) 0.75 Al 0.25 N (0 0 0 1) surface are built, then the atomic structure, electronic structure, adsorption energy, work function, dipole moment and optical properties of the models are calculated. All calculations are carried out using Cambridge Serial Total Energy Package (CASTEP) based on first principle. Results show that Cs adsorption on Mg doping Ga 1−x Al x N (0 0 0 1) surface can reduce work function of the surface, and the favorite adsorption site is on the top of p-type impurity. Cs adsorption on p-type Ga 1−x Al x N (0 0 0 1) surface can produce the structure of p-type bulk with n-type surface, which is helpful to surface band bend downward and decrease electron affinity seriously. The absorption coefficient of Cs adsorption system is less than that of the clean surface. Theoretical study of Cs adsorption on Ga 1−x Al x N (0 0 0 1) surface can help to improve activation technology of Ga 1−x Al x N photocathodes.

Effect of Novel Starter Culture on Reduction of Biogenic Amines, Quality Improvement, and Sensory Properties of Doenjang, a Traditional Korean Soybean Fermented Sauce Variety.

Science.gov (United States)

Shukla, Shruti; Lee, Jong Suk; Park, Hae-Kyong; Yoo, Jung-Ah; Hong, Sung-Yong; Kim, Jong-Kyu; Kim, Myunghee

2015-08-01

To select appropriate microorganisms as starter cultures for the reliable and reproducible fermentation of soybean fermented products of Korean Doenjang, various ratios of fungi (Aspergillus oryzae J, Mucor racemosus 15, M. racemosus 42) combined with Bacillus subtilis TKSP 24 were selected as either single, double, or multiple Meju strains for commercial mass production of Doenjang, followed by analysis of sensory characteristics. In the sensory evaluation, Doenjang BAM15-1 and BAM42-1, which were fermented with multiple strains (1:1:1), showed the highest sensory scores as compared to control. Based on sensory characteristics, 6 Doenjang samples were subjected to quantitative determination of amino acids, free sugars, and organic acids (volatile and nonvolatile) contents, followed by determination of biogenic amines. Total sweet taste amino acid contents were highest in BAM15-1 and BAM42-1 samples (333.7 and 295.8 mg/100 g, respectively) and similar that of control (391.1 mg/100 g). Samples BAM15-1 and BAM42-1 showed the relatively high volatile and nonvolatile organic acid contents (154.24, 192.26, and 71.31, 82.42 mg/100 g, respectively). In addition, BAM15-1 and BAM42-1 showed negligible biogenic amine formation, ranging from 0.00 to 1.02 and 0.00 to 3.92 mg/100 g, respectively. These findings indicate that determination of food components along with sensory and quality attributes using multiple microbial Meju strains as a starter culture may provide substantial results on improved quality fermented Doenjang products. © 2015 Institute of Food Technologists®

The high-temperature modification of LuAgSn and high-pressure high-temperature experiments on DyAgSn, HoAgSn, and YbAgSn

Energy Technology Data Exchange (ETDEWEB)

Heying, B.; Rodewald, U.C.; Hermes, W.; Schappacher, F.M.; Riecken, J.F.; Poettgen, R. [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Heymann, G.; Huppertz, H. [Muenchen Univ. (Germany). Dept. fuer Chemie und Biochemie; Sebastian, C.P. [Max-Planck-Institut fuer Chemische Physik Fester Stoffe, Dresden (Germany)

2008-02-15

The high-temperature modification of LuAgSn was obtained by arc-melting an equiatomic mixture of the elements followed by quenching the melt on a water-cooled copper crucible. HT-LuAgSn crystallizes with the NdPtSb-type structure, space group P6{sub 3}mc: a = 463.5(1), c = 723.2(1) pm, wR2 = 0.0270, 151 F{sup 2}, and 11 variables. The silver and tin atoms build up two-dimensional, puckered [Ag{sub 3}Sn{sub 3}] networks (276 pm Ag-Sn) that are charge-balanced and separated by the lutetium atoms. The Ag-Sn distances between the [Ag{sub 3}Sn{sub 3}] layers of 294 pm are much longer. Single crystals of isotypic DyAgSn (a = 468.3(1), c = 734.4(1) pm, wR2 = 0.0343, 411 F{sup 2}, and 11 variables) and HoAgSn (a = 467.2(1), c = 731.7(2) pm, wR2 = 0.0318, 330 F{sup 2}, and 11 variables) were obtained from arc-melted samples. Under high-pressure (up to 12.2 GPa) and high-temperature (up to 1470 K) conditions, no transitions to a ZrNiAl-related phase have been observed for DyAgSn, HoAgSn, and YbAgSn. HT-TmAgSn shows Curie-Weiss paramagnetism with {mu}{sub eff} = 7.53(1) {mu}{sub B}/Tm atom and {theta}P = -15.0(5) K. No magnetic ordering was evident down to 3 K. HT-LuAgSn is a Pauli paramagnet. Room-temperature {sup 119}Sn Moessbauer spectra of HT-TmAgSn and HT-LuAgSn show singlet resonances with isomer shifts of 1.78(1) and 1.72(1) mm/s, respectively. (orig.)

In-situ thermal analysis and macroscopical characterization of Mg-xCa and Mg-0.5Ca-xZn alloy systems

Energy Technology Data Exchange (ETDEWEB)

Farahany, Saeed [Department of Materials Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Bakhsheshi-Rad, Hamid Reza, E-mail: Rezabakhsheshi@gmail.com [Department of Materials Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Idris, Mohd Hasbullah [Department of Materials Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Abdul Kadir, Mohammed Rafiq [Medical Implants Technology Group, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Department of Biomechanics and Biomedical Materials, Faculty of Biomedical Engineering and Health Sciences, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Lotfabadi, Amir Fereidouni [Department of Manufacturing and Industrial Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Ourdjini, Ali [Department of Materials Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia)

2012-01-10

Highlights: Black-Right-Pointing-Pointer The effect of Ca and Zn addition on Mg-Ca and Mg-Ca-Zn were investigated. Black-Right-Pointing-Pointer Ca and Zn addition decreased solid fraction at coherency point. Black-Right-Pointing-Pointer T{sub N}-T{sub DCP} increased by adding Ca and Zn in Mg-Ca and Mg-Ca-Zn, respectively. Black-Right-Pointing-Pointer Three reactions were detected when Zn/Ca atomic ratio less than 1.25 in Mg-Ca-Zn. Black-Right-Pointing-Pointer A new peak Mg{sub 51}Zn{sub 20} was identified in Mg-0.5Ca-9Zn in addition of other peaks. - Abstract: This research described the identification phases by thermal analysis and microscopy inspection of Mg-xCa and Mg-0.5%Ca-xZn alloys that were solidified at slow cooling rate. Analysis of cooling curve after Ca addition shows the evolution of the Mg{sub 2}Ca intermetallic phase at around 520 Degree-Sign C in addition to {alpha}-Mg phase. First derivative curves of alloys after the addition of Zn to Mg-0.5Ca alloy reveals three peaks related to {alpha}-Mg, Mg{sub 2}Ca and Ca{sub 2}Mg{sub 6}Zn{sub 3} for alloys that have Zn/Ca atomic ratio less than 1.23. The peak of Mg{sub 2}Ca reaction on the first derivative curves disappeared for alloys containing Zn/Ca ratio more than 1.23. A new peak was also observed at 330 Degree-Sign C for Mg-0.5Ca-9Zn which was identified as Mg{sub 51}Zn{sub 20}. Solid fraction at coherency point decreased with increasing Ca and Zn elements. However, coherency time and difference between the nucleation and coherency temperatures (T{sub N}-T{sub DCP}) increased by adding Ca and Zn in Mg-Ca and Mg-Ca-Zn systems.

Biogenic nanomaterials from photosynthetic microorganisms.

Science.gov (United States)

Jeffryes, Clayton; Agathos, Spiros N; Rorrer, Gregory

2015-06-01

The use of algal cell cultures represents a sustainable and environmentally friendly platform for the biogenic production of nanobiomaterials and biocatalysts. For example, advances in the production of biogeneic nanomaterials from algal cell cultures, such as crystalline β-chitin nanofibrils and gold and silver nanoparticles, could enable the 'green' production of biomaterials such as tissue-engineering scaffolds or drug carriers, supercapacitors and optoelectric materials. The in vivo functionalization, as well as newly demonstrated methods of production and modification, of biogenic diatom biosilica have led to the development of organic-inorganic hybrid catalytic systems as well as new biomaterials for drug delivery, biosensors and heavy-metal adsorbents. Copyright © 2014 Elsevier Ltd. All rights reserved.

Preparation, characterization and antimicrobial property of ag+- nano Chitosan/ZSM-5: novel Hybrid Biocomposites

Directory of Open Access Journals (Sweden)

Maasoumeh Khatamiana

2016-10-01

Full Text Available Objective(s: Binary hybrids of chitosan-zeolite have many interesting applications in separation and bacteriostatic activity. Materials and Methods: Template free ZSM-5 zeolite was synthesized by hydrothermal method, physical hydrogels of nano chitosan in the colloidal domain were obtained in the absence of toxic organic solvent and then nano chitosan/ZSM-5 hybrid composites with nano chitosan contents of 0.35%, 3.5%, 35% wt.% were prepared. The as prepared hybrid composites were ion-exchanged with Ag cations. Results: XRD and FT-IR results revealed a good crystalinity of as synthesized template frees ZSM-5 with BET surface area of 307 m2g-1. Presence of chitosan in composites was confirmed by XRD patterns and FT-IR spectroscopic analysis, the chitosan content in composite was obtained with TG analysis. SEM analysis of composites shows that chitosan particles were dispersed within the nanometer scale. The antimicrobial activity of different samples was investigated and the results showed that the Ag+-exchanged samples have the highest antibacterial properties. Cancer cell line A549 cell line were cultured in designated medium treated with Ag+-exchanged samples at the concentration of 0.01 to 0.5 mg/ml. After 24 and 48 hours incubation, the efficacy of Ag+-exchanged samples to treat cancer cell lines were measured by means of cell viability test via MTT assay. Concentrations of 0.05 and 0.1 mg/ml of Ag+-exchanged samples induced a very low toxicity. Conclusion: These hybrid composite materials have potential applications on tissue engineering and antimicrobial food packaging.

Biogenic amines degradation by microorganisms isolated from cheese

Directory of Open Access Journals (Sweden)

Irena Butor

2017-01-01

Full Text Available The aim of this study was the isolation and characterization of microorganisms able to degrade biogenic amines and their identification. Individual microorganisms were obtained by isolation from commercially available foodstuffs and food produced in the technological laboratories of Faculty of Technology, Tomas Bata University in Zlín and subsequently identified by MALDI-TOF MS. The results of MALDI-TOF MS identification were verified by 16S rRNA sequenation. In this work was studied the ability of 5 bacterial strains positive to biogenic amines degradation isolated from dairy products to decrease biogenic amines content in vitro and quantified reduction in the concentration of biogenic amines tryptamine, β-phenylethylamine, putrescine, cadaverine, histamine and tyramine. The level of degradation (decrease of biogenic amines was determined on the base of the ability to grow in media with biogenic amines as the sole source carbon and nitrogen. The isolated strains with the ability of degradation of one or more biogenic amines were cultured in medium supplemented with relevant biogenic amines, the media derivatized with dansyl chloride and these amines separated by HPLC at a wavelength of 254 nm. From five tested strains identified as Bacillus subtilis, Bacillus pumilus, Enterobacter cloacae, Rhizobium radiobacter and Acinetobacter pitii, isolated from gouda type cheese, the greatest ability of degradation was observed in Bacillus subtilis, which was capable to degrade almost all amount of histamine, cadaverine and putrescine. Other four strains showed a lower rate of degradation than Bacillus subtilis, but the ability to degrade biogenic amines with these microorganisms was still significant.

Preparation of Bi-Pb-Sr-Ca-Cu-O high Tc thick films on Ag or MgO substrate with superconductor paste; Bi kei ko Tc chodendo paste ni yoru Ag, MgO kibanjo eno atsumaku sakusei

Energy Technology Data Exchange (ETDEWEB)

Takabatake, N. [Ishikawa Technical High School, Ishikawa (Japan); Tsubota, T.; Ishikawa, T.; Ohashi, K. [Kanazawa Institute of Technology, Ishikawa (Japan)

1995-07-15

The following were reported on making Bi series superconducting thick films by a wet method. A paste was made by adding PSO (or ethanol solution of ethylenegrycol) of Yushiro Chemical Industry Co., Ltd. as a binder to a Bi series 2223 single-phase powder sample (blending composition Bi:Pb:Sr:Ca:Cu=1.8:0.4:2:2:3.2); the sample was then coated on an Ag (or MgO) substrate with a brush; after being dried at 105{degree}C for one hour, it was thermally decomposed at 700{degree}C for one hour; then, the process of prissurized forming (at pressure 2 to 5 ton f/cm{sup 2}) and of sintering at 845{degree}C for 20 hours or more were performed on the sample to form a thick film sample. A critical temperature Tc, critical current density Jc, etc., were measured on such thick film sample. As a result, nearly same values were obtained as Tc (93K) and Jc (84A/cm{sup 2}) which were those of a bulk sample made by using the same powder sample, pressurizing at 2 ton f/cm{sup 2} for pelletizing, and sintering at 845{degree}C for 20 hours. 6 refs., 7 figs., 1 tab.

Enhanced elevated-temperature performance of LiAl_xSi_0_._0_5Mg_0_._0_5Mn_1_._9_0_-_xO_4 (0≤x≤0.08) cathode materials for high-performance lithium-ion batteries

International Nuclear Information System (INIS)

Zhao, Hongyuan; Liu, Shanshan; Wang, Zhenwei; Cai, Yu; Tan, Ming; Liu, Xingquan

2016-01-01

In order to significantly enhance the elevated-temperature performance of LiSi_0_._0_5Mg_0_._0_5Mn_1_._9_0O_4, the LiAl_xSi_0_._0_5Mg_0_._0_5Mn_1_._9_0_-_xO_4 (0 ≤ x ≤ 0.08) samples were firstly prepared via sol-gel technique. All the obtained samples showed the intrinsic spinel structure without any other detectable impurity phases. Among these samples, the LiAl_0_._0_5Si_0_._0_5Mg_0_._0_5Mn_1_._8_5O_4 sample was found to be optimal possessing regular crystal morphology with clean surfaces and presented much better elevated-temperature cycling stability and rate capability. When carried out at 55 °C, the LiAl_0_._0_5Si_0_._0_5Mg_0_._0_5Mn_1_._8_5O_4 sample exhibited the initial discharge capacity of 123.6 mAh g"−"1 at 0.5C between 3.20 and 4.35 V. After 100 cycles, the discharge capacity could still reach up to 115.9 mAh g"−"1 with capacity retention of 93.8%, which was much higher than that of LiSi_0_._0_5Mg_0_._0_5Mn_1_._9_0O_4. At the higher discharge rate of 10C, a high discharge capacity of 82.5 mAh g"−"1 could be obtained with capacity retention of 95.6% after 50 cycles at 55 °C. By contrast, the LiSi_0_._0_5Mg_0_._0_5Mn_1_._9_0O_4 sample only exhibited 43.7 mAh g"−"1 with lower capacity retention of 61.8%. These results indicate that the introduction of appropriate amount of aluminium ions in the magnesium and silicon co-doped spinel can make up for the shortage of co-doping with magnesium and silicon ions in term of the elevated-temperature performance.

Improvement of corrosion resistance in NaOH solution and glass forming ability of as-cast Mg-based bulk metallic glasses by microalloying

Directory of Open Access Journals (Sweden)

Peng Hao

2011-02-01

Full Text Available The influences of the addition of Ag on the glass forming ability (GFA and corrosion behavior were investigated in the Mg-Ni-based alloy system by X-ray diffraction (XRD and electrochemical polarization in 0.1 mol/L NaOH solution. Results shows that the GFA of the Mg-Ni-based BMGs can be improved dramatically by the addition of an appropriate amount of Ag; and the addition element Ag can improve the corrosion resistance of Mg-Ni-based bulk metallic glass. The large difference in atomic size and large negative mixing enthalpy in alloy system can contribute to the high GFA. The addition element Ag improves the forming speed and the stability of the passive film, which is helpful to decrease the passivation current density and to improve the corrosion resistance of Mg-Ni-based bulk metallic glass.

Effects of Mg substitution on the structural and magnetic properties of Co0.5Ni0.5-x Mg x Fe2O4 nanoparticle ferrites

Science.gov (United States)

R, M. Rosnan; Z, Othaman; R, Hussin; Ali, A. Ati; Alireza, Samavati; Shadab, Dabagh; Samad, Zare

2016-04-01

In this study, nanocrystalline Co-Ni-Mg ferrite powders with composition Co0.5Ni0.5-x Mg x Fe2O4 are successfully synthesized by the co-precipitation method. A systematic investigation on the structural, morphological and magnetic properties of un-doped and Mg-doped Co-Ni ferrite nanoparticles is carried out. The prepared samples are characterized using x-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), and vibrating sample magnetometry (VSM). The XRD analyses of the synthesized samples confirm the formation of single-phase cubic spinel structures with crystallite sizes in a range of ˜ 32 nm to ˜ 36 nm. The lattice constant increases with increasing Mg content. FESEM images show that the synthesized samples are homogeneous with a uniformly distributed grain. The results of IR spectroscopy analysis indicate the formation of functional groups of spinel ferrite in the co-precipitation process. By increasing Mg2+ substitution, room temperature magnetic measurement shows that maximum magnetization and coercivity increase from ˜ 57.35 emu/g to ˜ 61.49 emu/g and ˜ 603.26 Oe to ˜ 684.11 Oe (1 Oe = 79.5775 A·m-1), respectively. The higher values of magnetization M s and M r suggest that the optimum composition is Co0.5Ni0.4Mg0.1Fe2O4 that can be applied to high-density recording media and microwave devices. Project supported by the Ibnu Sina Institute for Scientific and Industrial Research, Physics Department of Universiti Teknologi Malaysia and the Ministry of Education Malaysia (Grant Nos. Q.J130000.2526.04H65).

Electronic structure of Rh-based CuRh0.9Mg0.1O2 oxide thermoelectrics

Science.gov (United States)

Vilmercati, P.; Martin, E.; Cheney, C. Parks; Bondino, F.; Magnano, E.; Parmigiani, F.; Sasagawa, T.; Mannella, N.

2013-03-01

The electronic structure of the Rh-based CuRh0.9Mg0.1O2 oxide thermoelectric compound has been studied with a multitechnique approach consisting of photoemission, x-ray absorption, and x-ray emission spectroscopies. The data indicate that the region of the valence band in the proximity of the Fermi level is dominated by Rh-derived states. These findings outline the importance of the electronic structure of the Rh ions for the large thermoelectric power in CuRh0.9Mg0.1O2 at high temperature.

Adsorption and Desorption Characteristics of Cd2+ and Pb2+ by Micro and Nano-sized Biogenic CaCO3

Science.gov (United States)

Liu, Renlu; Guan, Yong; Chen, Liang; Lian, Bin

2018-01-01

The purpose of this study was to elucidate the characteristics and mechanisms of adsorption and desorption for heavy metals by micro and nano-sized biogenic CaCO3 induced by Bacillus subtilis, and the pH effect on adsorption was investigated. The results showed that the adsorption characteristics of Cd2+ and Pb2+ are well described by the Langmuir adsorption isothermal equation, and the maximum adsorption amounts for Cd2+ and Pb2+ were 94.340 and 416.667 mg/g, respectively. The maximum removal efficiencies were 97% for Cd2+, 100% for Pb2+, and the desorption rate was smaller than 3%. Further experiments revealed that the biogenic CaCO3 could maintain its high adsorption capability for heavy metals within wide pH ranges (3–8). The FTIR and XRD results showed that, after the biogenic CaCO3 adsorbed Cd2+ or Pb2+, it did not produce a new phase, which indicated that biogenic CaCO3 and heavy metal ions were governed by a physical adsorption process, and the high adsorptive capacity of biogenic CaCO3 for Cd2+ and Pb2+ were mainly attributed to its large total specific surface area. The findings could improve the state of knowledge about biogenic CaCO3 formation in the environment and its potential roles in the biogeochemical cycles of heavy metals. PMID:29434577

The oscillations in ESR spectra of Hg0.76Cd0.24Te implanted by Ag+ at the X and Q-bands

Science.gov (United States)

Shestakov, A. V.; Fazlizhanov, I. I.; Yatsyk, I. V.; Gilmutdinov, I. F.; Ibragimova, M. I.; Shustov, V. A.; Eremina, R. M.

2018-05-01

The objects of the investigation were uniformly Ag+ doped Hg0.76Cd0.24Te mercury chalcogenide monocrystals obtained by ion implantation with subsequent thermal annealing over 20 days. After implantation and annealing the conductivity was inverted from n-type with carrier concentration of 1016 cm‑3 to p-type with carrier concentration of ≈ 3.9 × 1015 cm‑3. The investigations of microwave absorption derivative (dP/dH) showed the existence of strong oscillations in the magnetic field for Ag:Hg0.76Cd0.24Te in the temperature range 4.2–12 K. The concentration and effective mass of charge carrier were determined from oscillation period and temperature dependency of oscillation amplitude. We suppose that this phenomenon is similar to the de Haas–van Alphen effect in weakly correlated electron system with imperfect nesting vector.

Neogene biogenic sediments of onshore Peru: part I, sedimentology and stratigraphy

Energy Technology Data Exchange (ETDEWEB)

Marty, R.C.; Dunbar, R.B.; Baker, P.

1985-01-01

The Sechura (approx.6/sup 0/S) and Pisco (approx.14/sup 0/S) Basins of onshore Peru contain Miocene diatom and phosphate rich sediments which sharply contrast with underlying clastics. In the Sechura Basin the Miocene clastic Mancora, Heath and Montera Formations are overlain by the Zapallal Formation which grades upwards from a weakly biogenic base into fairly pure diatomites (biogenic silica >20%) and ore grade phosphorite (P/sub 2/O/sub 5/>20%). Biogeneic content decreases in the eastern basin as clastic content increases. The base of the Zapallal Formation has been dated at between 12.2 and 14.0 mybp using radiolaria correlated to magnetic stratigraphy by Theyer, et al (1978), and the phosphatic section yields dates of between 8.0 and 11.2 my. In the Pisco Basin the Eocene clastic Paracas Formation is overlain unconformably by the Miocene Pisco Formation which contains a basal sequence of cross-bedded clastics, tuffs, and partially recrystallized diatomites; a phosphorite bearing middle sequence; and a diatom rich top. Current direction from the cross beds of the basal Pisco Formation indicate a generally southerly transport direction but with considerable directional variability. This may be related to the Peru under-current which shows highly variable strength and direction near 15/sup 0/S.

Magnetic Properties of La0.9Ag0.1(Mn1-xCoxO3 under Pressure

Directory of Open Access Journals (Sweden)

Mihalik M.

2013-01-01

Full Text Available In our paper we report on magnetic properties of La0.90Ag0.10(CoxMn1-xO3 ferromagnetic ceramics (x = 0.00 and0.03 which were studied in pressures up to 0.9 GPa. Magnetic transition at the Curie temperature TC is accompanied with metal insulator transition with a maximum at T* which is shifted to lower temperature with applied magnetic field. The Curie temperature is decreasing with substitution of Co for Mn and is ranging from 178 K to 126.5 K. Hydrostatic pressure increases TC for sample with x = 0.03 nearly linearly with the pressure coefficient dTc/dp = 5.7 K/GPa. Hysteresis loop is affected marginally; µs increases and Hc decreases with pressure.

High figure of merit and thermoelectric properties of Bi-doped Mg2Si0.4Sn0.6 solid solutions

International Nuclear Information System (INIS)

Liu, Wei; Zhang, Qiang; Yin, Kang; Chi, Hang; Zhou, Xiaoyuan; Tang, Xinfeng; Uher, Ctirad

2013-01-01

The study of Mg 2 Si 1−x Sn x -based thermoelectric materials has received widespread attention due to a potentially high thermoelectric performance, abundant raw materials, relatively low cost of modules, and non-toxic character of compounds. In this research, Mg 2.16 (Si 0.4 Sn 0.6 ) 1−y Bi y solid solutions with the nominal Bi content of 0≤y≤0.03 are prepared using a two-step solid state reaction followed by spark plasma sintering consolidation. Within this range of Bi concentrations, no evidence of second phase segregation was found. Bi is confirmed to occupy the Si/Sn sites in the crystal lattice and behaves as an efficient n-type dopant in Mg 2 Si 0.4 Sn 0.6 . Similar to the effect of Sb, Bi doping greatly increases the electron density and the power factor, and reduces the lattice thermal conductivity of Mg 2.16 Si 0.4 Sn 0.6 solid solutions. Overall, the thermoelectric figure of merit of Bi-doped Mg 2.16 Si 0.4 Sn 0.6 solid solutions is improved by about 10% in comparison to values obtained with Sb-doped materials of comparable dopant content. This improvement comes chiefly from a marginally higher Seebeck coefficient of Bi-doped solid solutions. The highest ZT∼1.4 is achieved for the y=0.03 composition at 800 K. - Graphical abstract: (a)The relationship between electrical conductivity and power factor for Sb/Bi-doped Mg 2.16 (Si 0.4 Sn 0.6 ) 1−y (Sb/Bi) y (0 2.16 (Si 0.4 Sn 0.6 ) 1−y Bi y (0≤y≤0.03) solid solutions. (c)Temperature dependent dimensionless figure of merit ZT of Mg 2.16 (Si 0.4 Sn 0.6 ) 1−y Bi y (0≤y≤0.03) solid solutions. - Highlights: • Bi doped Mg 2.16 Si 0.4 Sn 0.6 showed 15% enhancement in the power factor as compared to Sb doped samples. • Bi doping reduced κ ph of Mg 2.16 Si 0.4 Sn 0.6 due to stronger point defect scattering. • The highest ZT=1.4 at 800 K was achieved for Mg 2.16 (Si 0.4 Sn 0.6 ) 0.97 Bi 0.03

Electrical studies of D%AgI-(100-D)%[0.667Ag2O- 0.333{(0.4)B2O3-(0.6)TeO2}] fast ion conducting glasses

Science.gov (United States)

Kumar, E. Ramesh; Nageswar Rao, P.; Appa Rao, B.

2016-09-01

Super ion conducting glasses of composition D%AgI-(100-D)%[MAg2O-F{(F1)B2O3- (F2)TeO2}]; D=10.0 to 60.0 in steps of 10.0 for a fixed values of F1 (0.4), F2 (0.6) which are glass network formers, fixed values of modifier M(0.667), F (0.333) and D is dopant salt which was varied. These glasses were prepared by melt quenching technique. XRD spectra taken for all the samples. Electrical characterization was done in terms of AC and DC conductivities. DC and AC conductivities at room temperature increased from 10-5 to 10-1 scm-1 and DC activation energy (Edc) found to decrease from 0.36 to 0.19eV with increase in D% ratio. Measurements are performed over the frequency range 1 kHz to 3 MHz at different temperatures. From the impedance spectroscopy real and imaginary parts of impedances (Z', Z"), conductivities were calculated and plotted, and equivalent R-C circuit parameters were obtained from Cole-Cole plots. With the increase in D%, AC conductivity is observed to increase whereas the AC activation energy (Eac) is observed to decrease from 0.23 to 0.14 eV. The quantitative analysis of these results indicates that the electrical conductivity of silver borate glasses is enhanced with increase in D% ratio. Based on conductivity values these glasses are ionic conductors, in which conduction is by hopping mechanism. An attempt is made to understand the charge transportation process.

Influence of silver concentration in Ag-x(Sb0.40S0.60)(100-x) thin amorphous films on photoinduced crystallization

Czech Academy of Sciences Publication Activity Database

Gutwirth, J.; Wágner, T.; Bezdička, Petr; Kotulanová, Eva; Vlček, Milan; Kasap, S. O.; Frumar, M.

2007-01-01

Roč. 9, č. 10 (2007), s. 3064-3071 ISSN 1454-4164 R&D Projects: GA MŠk LC523; GA ČR GA203/06/1368 Institutional research plan: CEZ:AV0Z40320502; CEZ:AV0Z40500505 Keywords : Ag-Sb-S films * amorphous * photoinduced crystallization Subject RIV: CA - Inorganic Chemistry Impact factor: 0.827, year: 2007

Construction of Ag/AgCl nanostructures from Ag nanoparticles as high-performance visible-light photocatalysts

Energy Technology Data Exchange (ETDEWEB)

Yang, Fan; Liu, Dongzhi; Wang, Tianyang; Li, Wei [Tianjin University, School of Chemical Engineering and Technology (China); Hu, Wenping [Tianjin University, Collaborative Innovation Center of Chemical Science and Engineering (China); Zhou, Xueqin, E-mail: zhouxueqin@tju.edu.cn [Tianjin University, School of Chemical Engineering and Technology (China)

2016-11-15

A combined strategy of in situ oxidation and assembly is developed to prepare Ag/AgCl nanospheres and nanocubes from Ag nanoparticles under room temperature. It is a new facile way to fabricate Ag/AgCl with small sizes and defined morphologies. Ag/AgCl nanospheres with an average size of 80 nm were achieved without any surfactants, while Ag/AgCl nanocubes with a mean edge length of 150 nm were obtained by introduction of N-dodecyl-N,N-dimethyl-2-ammonio-acetate. The possible formation mechanism involves the self-assembly of AgCl nanoparticles, Ostwald ripening and photoreduction of Ag{sup +} into Ag{sup 0} by the room light. The as-prepared Ag/AgCl nanospheres and nanocubes exhibit excellent photocatalytic activity and stability toward degradation of organic pollutants under visible-light irradiation. It is demonstrated that Ag/AgCl nanocubes display enhanced photocatalytic activity in comparison with Ag/AgCl nanospheres due to the more efficient charge transfer. This work may pave an avenue to construct various functional materials via the assembly strategy using nanoparticles as versatile building blocks.

Studies on Al-Cu-Li-Mg-Ag-Zr alloy processed through vacuum induction melting (VIM) technique

International Nuclear Information System (INIS)

Nayan, Niraj; Govind; Nair, K. Suseelan; Mittal, M.C.; Sudhakaran, K.N.

2007-01-01

A new technique of lithium addition has been adapted for the processing of Al-Cu-Li-Ag-Mg-Zr alloy, which gives more than 90% recovery of lithium throughout the billet. Processing studies on this alloy include casting, three step homogenization, to avoid incipient melting, and mechanical working particularly forging and rolling. The products in the form of sheets were subjected to various T6 (solution treatment + water quenching + aging) tempers. Mechanical properties were evaluated at room temperature and correlated with microstructure. Characterizations using optical microscope and post-fracture analysis have been carried out using Scanning electron microscope (SEM). Experimental investigation shows highest mechanical properties for the Al-1.3%Li alloy in T6 (500 deg. C/1 h + WQ + 190 deg. C/24 h) condition

Surface characterization, in vitro and in vivo biocompatibility of Mg-0.3Sr-0.3Ca for temporary cardiovascular implant

Energy Technology Data Exchange (ETDEWEB)

Bornapour, M., E-mail: mandana.bornapour@mail.mcgill.ca [Light Metals and Advanced Magnesium Materials, Mining and Materials Engineering, McGill University, Montreal, Qc, H3A 0C5 (Canada); Biointerface Lab, Mining and Materials Engineering, McGill University, Montreal, Qc H3A 0C5 (Canada); Mahjoubi, H. [Biointerface Lab, Mining and Materials Engineering, McGill University, Montreal, Qc H3A 0C5 (Canada); Vali, H. [Department of Anatomy and Cell Biology, McGill University, Montreal, Qc, H3A 0C7 (Canada); Shum-Tim, D. [Department of Cardiac Surgery and Surgical Research, McGill University, Montreal, Qc H3G 1A1 (Canada); Cerruti, M. [Biointerface Lab, Mining and Materials Engineering, McGill University, Montreal, Qc H3A 0C5 (Canada); Pekguleryuz, M. [Light Metals and Advanced Magnesium Materials, Mining and Materials Engineering, McGill University, Montreal, Qc, H3A 0C5 (Canada)

2016-10-01

Magnesium-based alloys are attractive candidate materials for medical applications. Our earlier work showed that the ternary Mg-0.3Sr-0.3Ca alloy exhibits slower degradation rates than both binary Mg-Sr and Mg-Ca alloys. The ternary alloy immersed in simulated body fluid (SBF) forms a compact surface layer of corrosion products that we hypothesized to be a Sr-substituted hydroxyapatite (HA). The main objectives of the current work are to understand the bio-degradation mechanism of Mg-0.3Sr-0.3Ca, to identify the exact nature of its protective layer and to evaluate the in vitro and in vivo biocompatibility of the alloy for cardiovascular applications. To better simulate the physiological environment, the alloy was immersed in SBF which was daily refreshed. Raman spectroscopy and X-Ray photoelectron spectroscopy (XPS) confirmed the formation of a thin, Sr-substituted HA layer at the interface between the alloy and the corrosion products. In vitro biocompatibility evaluated via indirect cytotoxicity assays using HUVECs showed no toxicity effect and ions extracted from Mg-0.3Sr-0.3Ca in fact increased the viability of HUVECs after one week. In vivo tests were performed by implanting a tubular Mg-0.3Sr-0.3Ca stent along with a WE43 control stent into the right and left femoral artery of a dog. Post implantation and histological analyses showed no thrombosis in the artery with Mg-0.3Sr-0.3Ca stent after 5 weeks of implantation while the artery implanted with WE43 stent was extensively occluded and thrombosed. Microscopic observation of the Mg-0.3Sr-0.3Ca implant-tissue interface confirmed the in situ formation of Sr-substituted HA on the surface during in vivo test. These results show that the interfacial layer protects the surface of the Mg-0.3Sr-0.3Ca alloy both in vitro and in vivo, and is the key factor in the bio-corrosion resistance of the alloy. - Highlights: • The surface active elements of Sr and Ca alter the corrosion of Mg alloy in SBF • Sr

Surface characterization, in vitro and in vivo biocompatibility of Mg-0.3Sr-0.3Ca for temporary cardiovascular implant

International Nuclear Information System (INIS)

Bornapour, M.; Mahjoubi, H.; Vali, H.; Shum-Tim, D.; Cerruti, M.; Pekguleryuz, M.

2016-01-01

Magnesium-based alloys are attractive candidate materials for medical applications. Our earlier work showed that the ternary Mg-0.3Sr-0.3Ca alloy exhibits slower degradation rates than both binary Mg-Sr and Mg-Ca alloys. The ternary alloy immersed in simulated body fluid (SBF) forms a compact surface layer of corrosion products that we hypothesized to be a Sr-substituted hydroxyapatite (HA). The main objectives of the current work are to understand the bio-degradation mechanism of Mg-0.3Sr-0.3Ca, to identify the exact nature of its protective layer and to evaluate the in vitro and in vivo biocompatibility of the alloy for cardiovascular applications. To better simulate the physiological environment, the alloy was immersed in SBF which was daily refreshed. Raman spectroscopy and X-Ray photoelectron spectroscopy (XPS) confirmed the formation of a thin, Sr-substituted HA layer at the interface between the alloy and the corrosion products. In vitro biocompatibility evaluated via indirect cytotoxicity assays using HUVECs showed no toxicity effect and ions extracted from Mg-0.3Sr-0.3Ca in fact increased the viability of HUVECs after one week. In vivo tests were performed by implanting a tubular Mg-0.3Sr-0.3Ca stent along with a WE43 control stent into the right and left femoral artery of a dog. Post implantation and histological analyses showed no thrombosis in the artery with Mg-0.3Sr-0.3Ca stent after 5 weeks of implantation while the artery implanted with WE43 stent was extensively occluded and thrombosed. Microscopic observation of the Mg-0.3Sr-0.3Ca implant-tissue interface confirmed the in situ formation of Sr-substituted HA on the surface during in vivo test. These results show that the interfacial layer protects the surface of the Mg-0.3Sr-0.3Ca alloy both in vitro and in vivo, and is the key factor in the bio-corrosion resistance of the alloy. - Highlights: • The surface active elements of Sr and Ca alter the corrosion of Mg alloy in SBF • Sr

Synthesis and Characterization of Pt-Ag Alloy Nanocages with Enhanced Activity and Durability toward Oxygen Reduction.

Science.gov (United States)

Yang, Xuan; Roling, Luke T; Vara, Madeline; Elnabawy, Ahmed O; Zhao, Ming; Hood, Zachary D; Bao, Shixiong; Mavrikakis, Manos; Xia, Younan

2016-10-12

Engineering the elemental composition of metal nanocrystals offers an effective strategy for the development of catalysts or electrocatalysts with greatly enhanced activity. Herein, we report the synthesis of Pt-Ag alloy nanocages with an outer edge length of 18 nm and a wall thickness of about 3 nm. Such nanocages with a composition of Pt 19 Ag 81 could be readily prepared in one step through the galvanic replacement reaction between Ag nanocubes and a Pt(II) precursor. After 10 000 cycles of potential cycling in the range of 0.60-1.0 V as in an accelerated durability test, the composition of the nanocages changed to Pt 56 Ag 44 , together with a specific activity of 1.23 mA cm -2 toward oxygen reduction, which was 3.3 times that of a state-of-the-art commercial Pt/C catalyst (0.37 mA cm -2 ) prior to durability testing. Density functional theory calculations attributed the increased activity to the stabilization of the transition state for breaking the O-O bond in molecular oxygen. Even after 30 000 cycles of potential cycling, the mass activity of the nanocages only dropped from 0.64 to 0.33 A mg -1 Pt , which was still about two times that of the pristine Pt/C catalyst (0.19 A mg -1 Pt ).

Preventing dewetting during rapid-thermal annealing of FePt films with enhanced L1{sub 0} ordering by introducing Ag cap-layers

Energy Technology Data Exchange (ETDEWEB)

Hsiao, S.N., E-mail: pmami.hsiao@gmail.com [Department of Materials Science and Engineering, Feng Chia University, Taichung 40724, Taiwan (China); Department of Power Mechanical Engineering, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Wu, S.C. [Department of Materials Science and Engineering, National Chung Hsing University, Taichung 40227, Taiwan (China); Liu, S.H. [Department of Materials Science and Engineering, Feng Chia University, Taichung 40724, Taiwan (China); Tsai, J.L., E-mail: tsaijl@dragon.nchu.edu.tw [Department of Materials Science and Engineering, National Chung Hsing University, Taichung 40227, Taiwan (China); Chen, S.K. [Department of Materials Science and Engineering, Feng Chia University, Taichung 40724, Taiwan (China); Chang, Y.C. [Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Lee, H.Y. [Scientific Research Division, National Synchrotron Radiation Research Center, Hsinchu 30077, Taiwan (China)

2015-11-15

High-order FePt continuous films with a strong (001) texture were fabricated on a glass substrate by introducing Ag layers and rapid thermal annealing (RTA). The dewetting of the (001)-textured FePt was suppressed during RTA with high heating rates (>80 K/s). The Ag cap layers not only increased the in-plane tensile stress, but also improved the (001) anisotropy and L1{sub 0} ordering of the FePt layers. All continuous Ag/FePt bilayer films possessed strong perpendicular anisotropies and high-ordered states irrespective of the Ag layer thickness. - Highlights: • Dewetting of (001) FePt fims were suppressed by introducing Ag cap layers. • Ag layers enhanced in-plane tensile stress, (001) texture and L1{sub 0} ordering. • Irrespective of Ag thickness, the Ag/FePt films exhibited strong (001) texture.

Carbon dot-Au(i)Ag(0) assembly for the construction of an artificial light harvesting system.

Science.gov (United States)

Jana, Jayasmita; Aditya, Teresa; Pal, Tarasankar

2018-03-06

Artificial light harvesting systems (LHS) with inorganic counterparts are considered to be robust as well as mechanistically simple, where the system follows the donor-acceptor principle with an unchanged structural pattern. Plasmonic gold or silver nanoparticles are mostly chosen as inorganic counterparts to design artificial LHS. To capitalize on its electron accepting capability, Au(i) has been considered in this work for the synergistic stabilization of a system with intriguingly fluorescing silver(0) clusters produced in situ. Thus a stable fluorescent Au(i)Ag(0) assembly is generated with electron accepting capabilities. On the other hand, carbon dots have evolved as new fluorescent probes due to their unique physicochemical properties. Utilizing the simple electronic behavior of carbon dots, an electronic interaction between the fluorescent Au(i)Ag(0) and a carbon dot has been investigated for the construction of a new artificial light harvesting system. This coinage metal assembly allows surface energy transfer where it acts as an acceptor, while the carbon dot behaves as a good donor. The energy transfer efficiency has been calculated experimentally to be significant (81.3%) and the Au(i)Ag(0)-carbon dot assembly paves the way for efficient artificial LHS.

Thermal expansion of CeCu5.8Ag0.2

International Nuclear Information System (INIS)

Kuechler, R.; Gegenwart, P.; Heuser, K.; Scheidt, E.-W.; Stewart, G.R.; Steglich, F.

2005-01-01

We present low-temperature thermal expansion measurements on the heavy fermion system CeCu 5.8 Ag 0.2 , which is located at an antiferromagnetic (AF) quantum critical point (QCP). At zero magnetic field, the volume expansion coefficient divided by temperature shows a logarithmic divergence upon cooling below 1K. This temperature dependence is incompatible with the predictions of the itinerant spin-density wave theory for an AF QCP. The application of magnetic fields leads to a cross-over to Landau Fermi liquid behavior as expected for a zero-field QCP

Surface characterization, in vitro and in vivo biocompatibility of Mg-0.3Sr-0.3Ca for temporary cardiovascular implant.

Science.gov (United States)

Bornapour, M; Mahjoubi, H; Vali, H; Shum-Tim, D; Cerruti, M; Pekguleryuz, M

2016-10-01

Magnesium-based alloys are attractive candidate materials for medical applications. Our earlier work showed that the ternary Mg-0.3Sr-0.3Ca alloy exhibits slower degradation rates than both binary Mg-Sr and Mg-Ca alloys. The ternary alloy immersed in simulated body fluid (SBF) forms a compact surface layer of corrosion products that we hypothesized to be a Sr-substituted hydroxyapatite (HA). The main objectives of the current work are to understand the bio-degradation mechanism of Mg-0.3Sr-0.3Ca, to identify the exact nature of its protective layer and to evaluate the in vitro and in vivo biocompatibility of the alloy for cardiovascular applications. To better simulate the physiological environment, the alloy was immersed in SBF which was daily refreshed. Raman spectroscopy and X-Ray photoelectron spectroscopy (XPS) confirmed the formation of a thin, Sr-substituted HA layer at the interface between the alloy and the corrosion products. In vitro biocompatibility evaluated via indirect cytotoxicity assays using HUVECs showed no toxicity effect and ions extracted from Mg-0.3Sr-0.3Ca in fact increased the viability of HUVECs after one week. In vivo tests were performed by implanting a tubular Mg-0.3Sr-0.3Ca stent along with a WE43 control stent into the right and left femoral artery of a dog. Post implantation and histological analyses showed no thrombosis in the artery with Mg-0.3Sr-0.3Ca stent after 5weeks of implantation while the artery implanted with WE43 stent was extensively occluded and thrombosed. Microscopic observation of the Mg-0.3Sr-0.3Ca implant-tissue interface confirmed the in situ formation of Sr-substituted HA on the surface during in vivo test. These results show that the interfacial layer protects the surface of the Mg-0.3Sr-0.3Ca alloy both in vitro and in vivo, and is the key factor in the bio-corrosion resistance of the alloy. Copyright © 2016 Elsevier B.V. All rights reserved.

The crystal structure of ramdohrite Pb_5.9Fe_0.1Mn_0.1In_0.1Cd_0.2Ag_2.8Sb_10.8S₂₄

DEFF Research Database (Denmark)

Makovicky, Emil; Mumme, William G.; Gable, Robert W.

2013-01-01

The crystal structure of ramdohrite, Pb5.9Fe0.1Mn0.1In0.1Cd0.2Ag2.8Sb10.8S24, from the Chocaya mine, Potosí, Bolivia, determined by Makovicky and Mumme from film data in 1983, was refined from single-crystal diffractometer data to the R value 0.060, based on 5230 reflections [I > 2σ(I)] from...... a twinned crystal. Lattice parameters are a = 8.7348(3), b = 13.0543(4), c = 19.3117(6) Å, and β = 90.179(2)°, space group P21/n. Two bicapped trigonal prismatic sites of lead bridge and unite adjacent (311)PbS slabs. These slabs contain five distinct coordination pyramids of Sb with trapezoidal cross...... sections, a mixed and disordered Sb-Ag-Cd-(Pb) site, refined as 0.39 Sb + 0.61 Ag, a pure Ag site with a very open, irregular tetrahedral coordination, and an octahedral site occupied by Pb. The (311)PbS slabs contain large lone electron pair micelles formed by four distinct antimony sites in alternation...

Efficacy and tolerability of tamsulosin 0.4 mg in Asian patients with lower urinary tract symptoms secondary to benign prostatic hyperplasia refractory to tamsulosin 0.2 mg: a randomized placebo controlled trial.

Science.gov (United States)

Kim, Jung Jun; Han, Deok Hyun; Sung, Hyun Hwan; Choo, Seol Ho; Lee, Sung Won

2014-07-01

To evaluate the efficacy and safety of tamsulosin dose increase to 0.4 mg daily in Asian patients with lower urinary tract symptoms secondary to benign prostatic hyperplasia refractory to tamsulosin 0.2 mg treatment. We carried out a 12-week, single-center, randomized, placebo-controlled trial in 220 patients. Patients treated with 0.2 mg tamsulosin daily without other lower urinary tract symptoms secondary to benign prostatic hyperplasia medication for more than 3 months and refractory to this treatment were enrolled. We defined "refractory" as an International Prostate Symptom Score of 13 or greater and a maximum flow rate of 15 or under despite medication. Patients with a surgical history related to lower urinary tract symptoms secondary to benign prostatic hyperplasia or a postvoid residual of 150 mL or greater were excluded. Eligible patients were randomly assigned to the 0.4 mg group (two tablets of 0.2 mg tamsulosin once daily) or the 0.2 mg group (one tablet of 0.2 mg tamsulosin and one tablet of placebo once daily). International Prostate Symptom Score, maximum flow rate, blood pressure, heart rate, and adverse events were compared between the two groups at 4 weeks and 12 weeks. A total of 220 patients were enrolled and analyzed. There were no differences in baseline characteristics between the two groups. After 12 weeks of medication, the International Prostate Symptom Score was not different between the two groups. However, the improvement in maximum flow rate was greater in the 0.4 mg group than the 0.2 mg group (3.0 ± 0.48 mL/s vs -0.25 ± 0.30 mL/s, P Tamsulosin 0.4 mg appears to be a safe treatment regimen for treating lower urinary tract symptoms secondary to benign prostatic hyperplasia in Asian patients who do not respond to 0.2 mg treatment. Increasing the dose of tamsulosin results in a significant improvement in maximum flow rate without any increase in cardiovascular complications. © 2014 The

Ag doped (Bi1.6Pb0.4Sr2CaCu2O8+δ textured rods

Directory of Open Access Journals (Sweden)

Díez, J. C.

2008-06-01

Full Text Available In this work, superconducting samples of (Bi1.6Pb0.4Sr2CaCu2O8+δ with Ag additions have been studied. (Bi1.6Pb0.4Sr2CaCu2O8+δ + x wt.% Ag (with x = 0, 1 and 3 powders were synthesized using a sol-gel method. The obtained powders were used as precursors to fabricate long textured cylindrical bars through a floating zone melting method. A drastic change on the microstructure has been found when comparing with undoped Bi2Sr2CaCu2O8+δ samples. The results showed that electrical resistivity at room temperature, critical current as well as flexural strength are improved when Ag is added to these Pb doped samples, while critical temperature does not change. On the other hand, it has been found that samples with composition (Bi1.6Pb0.4Sr2CaCu2O8+δ + Ag shown E-I curves with very high sharpness values on the zone of the superconducting to normal transition, reaching n-values (E∼In as high as 45 at 65K.Se han preparado polvos cerámicos de composición (Bi1.6Pb0.4Sr2CaCu2O8+δ + x % Ag en peso (con x = 0, 1 y 3 mediante un proceso sol-gel. Estos polvos se han utilizado para fabricar precursores que se texturaron por medio del método de fusión zonal flotante. Se ha encontrado un gran cambio en la microestructura cuando se compara con muestras de composición pura Bi2Sr2CaCu2O8+δ. Tanto la resistividad eléctrica a temperatura ambiente, como la corriente crítica, así como la resistencia a flexión se mejoran cuando la Ag se adiciona a estas muestras dopadas con Pb, mientras que no se observa cambio en la temperatura crítica. Por otra parte, se ha encontrado que las muestras de composición (Bi1.6Pb0.4Sr2CaCu2O8+δ + Ag presentan una gran pendiente de la curva E-I en la zona de transición entre el estado superconductor y el estado normal. Con estas composiciones, se han encontrado valores de n (E∼In de hasta 45 a 65K.

Structural and electrical properties of ZnO/Zn0.85Mg0.15O thin film prepared by pulsed laser deposition

Science.gov (United States)

Yang, Jing-Jing; Wang, Gang; Du, Wen-Han; Xiong, Chao

2017-07-01

The electrical transport properties are the key factors to determine the performance of ZnO-based quantum effect device. ZnMgO is a typical material to regulate the band of ZnO. In order to investigate the electrical properties of the interface of ZnO/Zn0.85Mg0.15O films, three kinds of ZnO/Zn0.85Mg0.15O films have been fabricated with different thickness. After comparing the structural and electrical properties of the samples, we found that the independent Zn0.85Mg0.15O hexagonal wurtzite structure (002) peak can be detected in XRD spectra. Hall-effect test data confirmed that the two-dimensional electron gas (2DEG) became lower because of the decrease of thickness of Zn0.85Mg0.15O films, increase of impurity scattering and lattice structure distortion caused by the increase of Mg content.

Effect of Solder-Joint Geometry on the Low-Cycle Fatigue Behavior of Sn- xAg-0.7Cu

Science.gov (United States)

Lee, Hwa-Teng; Huang, Kuo-Chen

2016-12-01

Low-cycle fatigue tests of Sn-Ag-Cu (SAC) Pb-free solder joints under fixed displacement were performed to evaluate the influence of Ag content (0-3 wt.%) and solder-joint geometry (barrel and hourglass types) on solder-joint fatigue behavior and reliability. The solder joints were composed of fine particles of Ag3Sn and Cu6Sn5, which aggregated as an eutectic constituent at grain boundaries of the primary β-Sn phase and formed a dense network structure. A decrease in the Ag content resulted in coarsening of the β-Sn and eutectic phases, which, in turn, decreased the strength of the joint and caused earlier failure. Solder joints in the hourglass form exhibited better fatigue performance with longer life than barrel-type joints. The sharp contact angle formed between the solder and the Cu substrate by the barrel-type joints concentrated stress, which compromised fatigue reliability. The addition of Ag to the solder, however, enhanced fatigue performance because of strengthening caused by Ag3Sn formation. The cracks of the barrel-type SAC solder joints originated mostly at the contact corner and propagated along the interfacial layer between the interfacial intermetallic compound (IMC) and solder matrix. Hourglass-type solder joints, however, demonstrated both crack initiation and propagation in the solder matrix (solder mode). The addition of 1.5-2.0 wt.% Ag to SAC solder appears to enhance the fatigue performance of solder joints while maintaining sufficient strength.

Impact of biogenic emissions on ozone formation in the Mediterranean area - a BEMA modelling study

International Nuclear Information System (INIS)

Thunis, P.; Cuvelier, C.

2000-01-01

The aim of this modelling study is to understand and quantify the influence of biogenic volatile organic compound (BVOC) emissions on the formation of tropospheric ozone in the Burriana area (north of Valencia) on the east coast of Spain. The mesoscale modelling system used consists of the meteorology/transport module TVM and the chemical reaction mechanism RACM. The results of the model simulations are validated and compared with the data collected during the biogenic emissions in the mediterranean area (BEMA) field campaign that took place in June 1997. Anthropogenic and biogenic emission inventories have been constructed with an hourly resolution. Averaged (over the land area and over 24 h) emission fluxes for AVOC, anthropogenic NO x , BVOC and biogenic NO x are given by 16.0, 9.9, 6.2, and 0.7 kg km -2 day -1 , respectively. The impact of biogenic emissions is investigated on peak ozone values by performing simulations with and without biogenic emissions; while keeping anthropogenic emissions constant. The impact on ozone formation is also studied in combination with some anthropogenic emissions reduction strategies, i.e. when anthropogenic VOC emissions and/or NO x emissions are reduced. A factor separation technique is applied to isolate the impact due to biogenic emissions from the overall impact due to biogenic and anthropogenic emissions together. The results indicate that the maximum impact of biogenic emissions on ozone formation represents at the most 10 ppb, while maximum ozone values are of the order of 100 ppb. At different locations the maximum impact is reached at different times of the day depending on the arrival time of the sea breeze. It is also shown that this impact does not coincide in time with the maximum simulated ozone concentrations that are reached over the day. By performing different emission reduction scenarios, BVOC impacts are found to be sensitive mainly to NO x , and not to AVOC. Finally, it is shown that amongst the various

In vivo bio-distribution, clearance and toxicity assessment of biogenic silver and gold nanoparticles synthesized from Abutilon indicum in Wistar rats.

Science.gov (United States)

Mata, Rani; Nakkala, Jayachandra Reddy; Chandra, Varshney Khub; Raja, Kumar; Sadras, Sudha Rani

2018-07-01

This study reports the bio-distribution and clearance of Abutilon indicum silver and gold nanoparticles (AIAgNPs and AIAuNPs) in Wistar rats. Rats in different groups were orally administered with 5 and 10 mg/Kg BW of AIAgNPs and AIAuNPs (size 1-25 nm) for 28 days and few were maintained until 58 days of washout period. Serum biochemical parameters were not changed significantly at both doses of AIAuNPs and at lower concentration of AIAgNPs. But, with 10 mg/Kg BW of AIAgNPs rats showed elevated levels of AST, ALP and ALT on day 29, however, these levels were restored to normal after washout period. Liver oxidative stress markers were not altered with the treatment of AIAgNPs and AIAuNPs. ICP-OES analysis indicated bio-distribution of Ag and Au more in liver, kidney and spleen on day 29 and was found cleared on day 59. Histological analysis of nine vital organs indicated normal tissue architecture at both doses of AIAuNPs and lower dose of AIAgNPs. While the rats treated with higher dose of AIAgNPs showed mild liver sinusoid cell swelling on day 29, which also was recovered on day 59. Findings of this preclinical study indicate biocompatible nature of biogenic nanoparticles supporting their future biomedical applications. Copyright © 2018 Elsevier GmbH. All rights reserved.

Additive impairment of the barrier function and irritation by biogenic amines and sodium lauryl sulphate: a controlled in vivo tandem irritation study.

Science.gov (United States)

Fluhr, J W; Kelterer, D; Fuchs, S; Kaatz, M; Grieshaber, R; Kleesz, P; Elsner, P

2005-01-01

Biogenic amines are potential irritants e.g. in fish-, meat-, milk- and egg-processing professions like cooks, butchers and bakers. The aim of this study was to test the irritative and barrier-disrupting properties of the biogenic amines ammonium hydroxide (AM), dimethylamine (DMA) and trimethylamine (TMA). A repeated sequential irritation of 30 min twice per day was performed over a total of 4 days (tandem repeated irritation test) on the back of 20 healthy volunteers of both sexes with AM, DMA, TMA and sodium lauryl sulphate (SLS). The epidermal barrier function was assessed with a Tewameter TM 210, stratum corneum surface pH was measured with a Skin-pH-Meter 900, inflammation was assessed with a Chromameter CR-300 on the a* axis for redness and a visual score was recorded. All tested biogenic amines (AM, DMA and TMA) induced a barrier disruption and a pH increase paralleled with a 1-day-delayed onset of inflammatory signs. These effects were further enhanced and accelerated by a sequential application of SLS together with the biogenic amines, and inflammation occurred earlier than with the single compounds. Acetic acid (AA) in contrast did only show mild barrier disruption and no significant inflammatory signs. Our system allowed a ranking of the different compounds in their irritative potential in the tandem irritation with SLS: SLS > NaOH > TMA > AA > AM > DMA. The results are suggestive that in the food-processing industry the simultaneous contact with biogenic amines and harmful detergents like SLS should be minimized. Copyright 2005 S. Karger AG, Basel.

Core/shell AgNi/PtAgNi nanoparticles as methanol-tolerant oxygen reduction electrocatalysts

International Nuclear Information System (INIS)

Wu, Dengfeng; Cheng, Daojian

2015-01-01

A core/shell AgNi/PtAgNi nanoparticle (NP) was synthesized via a new seed-mediated growth method in organic solvent medium. The as-synthesized AgNi/PtAgNiNP exhibits an AgNi core coated with PtAgNi shell, which was confirmed by transmission electron microscopy (TEM), ultraviolet–visible absorption spectroscopy and X-ray Photoelectron Spectroscopy (XPS). The AgNi/PtAgNiNPs/C catalyst possesses higher oxygen reduction reaction (ORR) activity and better durability compared with the commercial Pt/C catalyst. It is found that the ORR polarization curve of the AgNi/PtAgNiNPs/C catalyst shows an onset potential of 0.91 V vs. RHE, which is superior to the commercial Pt/C (0.88 V vs. RHE). In addition, the AgNi/PtAgNiNPs/C catalyst shows much better durability than the commercial Pt/C catalyst. More interestingly, the AgNi/PtAgNiNPs/C catalyst displays much higher methanol tolerance than the commercial Pt/C catalyst in 0.1 M KOH solution in the presence of 0.5 M methanol. Our results show that core/shell AgNi/PtAgNiNPs possess selective activity for ORR even in the presence of methanol, showing potential application as methanol-tolerant cathode catalysts in direct methanol fuel cells.

Antibacterial Ag/a-C nanocomposite coatings: The influence of nano-galvanic a-C and Ag couples on Ag ionization rates

Energy Technology Data Exchange (ETDEWEB)

Manninen, N.K., E-mail: nora.sousa@dem.uc.pt [SEG-CEMUC, Mechanical Engineering Department, University of Coimbra, 3030-788 Coimbra (Portugal); GRF-CFUM, Physics Department, University of Minho, Campus of Azurém, 4800-058 Guimarães (Portugal); Calderon, S. [SEG-CEMUC, Mechanical Engineering Department, University of Coimbra, 3030-788 Coimbra (Portugal); GRF-CFUM, Physics Department, University of Minho, Campus of Azurém, 4800-058 Guimarães (Portugal); Carvalho, I. [GRF-CFUM, Physics Department, University of Minho, Campus of Azurém, 4800-058 Guimarães (Portugal); CEB—Centre of Biological Engineering, LIBRO-Laboratório de Investigação em Biofilmes Rosário Oliveira, University of Minho, 4710-057 Braga (Portugal); Henriques, M. [CEB—Centre of Biological Engineering, LIBRO-Laboratório de Investigação em Biofilmes Rosário Oliveira, University of Minho, 4710-057 Braga (Portugal); Cavaleiro, A. [SEG-CEMUC, Mechanical Engineering Department, University of Coimbra, 3030-788 Coimbra (Portugal); Carvalho, S. [SEG-CEMUC, Mechanical Engineering Department, University of Coimbra, 3030-788 Coimbra (Portugal); GRF-CFUM, Physics Department, University of Minho, Campus of Azurém, 4800-058 Guimarães (Portugal)

2016-07-30

Highlights: • Amorphous carbon (a-C), Ag/a-C and Ag coatings were deposited by magnetron sputtering. • a-C/Ag coating shows antibacterial activity against S. epidermidis. • The formation of nano-galvanic couples in a-C/Ag enhances the Ag{sup +} ionization rate. • The Ag{sup +} ionization occurs along with Ag nanoparticles agglomeration in 0.9% NaCl. - Abstract: Biofilm formation has been pointed as a major concern in different industrial applications, namely on biomedical implants and surgical instruments, which has prompted the development of new strategies for production of efficient antimicrobial surfaces. In this work, nano-galvanic couples were created to enhance the antibacterial properties of silver, by embedding it into amorphous carbon (a-C) matrix. The developed Ag/a-C nanocomposite coatings, deposited by magnetron sputtering, revealed an outstanding antibacterial activity against Staphylococcus epidermidis, promoting a total reduction in biofilm formation with no bacteria counts in all dilution. The open circuit potential (OCP) tests in 0.9% NaCl confirmed that a-C shows a positive OCP value, in contrast to Ag coating, thus enhancing the ionization of biocidal Ag{sup +} due to the nano-galvanic couple activation. This result was confirmed by the inductively coupled plasma-optical emission spectroscopy (ICP-OES), which revealed a higher Ag ionization rate in the nanocomposite coating in comparison with the Ag coating. The surface of Ag/a-C and Ag coatings immersed in 0.9% NaCl were monitored by scanning electron microscopy (SEM) over a period of 24 h, being found that the Ag ionization determined by ICP-OES was accompanied by an Ag nanoparticles coalescence and agglomeration in Ag/a-C coating.

Structural and magnetic properties of Ni0.15Mg0.1Cu0.3Zn0.45Fe2O4 ferrite prepared by NaOH-precipitation method

International Nuclear Information System (INIS)

Hou, Wei-xiao; Wang, Zhi

2015-01-01

Highlights: • NiMgCuZn ferrites were successfully prepared by low-temperature sintering. • NiMgCuZn ferrites have the advantages of both NiCuZn and MgCuZn ferrites. • NiMgCuZn ferrites exhibit high Curie temperature & high stability of permeability. - Abstract: The Ni 0.15 Mg 0.1 Cu 0.3 Zn 0.45 Fe 2 O 4 ferrite powders have been prepared by NaOH co-precipitation method and characterized by X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). The XRD patterns confirm the single phase spinel structure of synthesized nanoparticles. The average crystallite size of the particles increases from 12 to 36 nm with calcining temperature (T a ) from 500 to 800 °C. The saturation magnetization (M s ) of the superparamagnetic particles was deduced by Langevin theory. Subsequently, the densification characteristics and magnetic properties of the low-temperature 950 °C-sintered ferrite bulk samples were also investigated. The magnetic measurement showed that the sintered bulk sample of T a = 600 °C has the highest initial permeability (μ i ), lowest coercivity (H c ), largest saturation magnetization (M s ) and satisfactory thermal stability of μ i . The microstructures of sintered samples were examined using field emission scanning electric microscope (FESEM). The T a has significant influence on the bulk density, initial permeability, saturation magnetization and coercivity of Ni 0.15 Mg 0.1 Cu 0.3 Zn 0.45 Fe 2 O 4 ferrite

An intercomparison of biogenic emissions estimates from BEIS2 and BIOME: Reconciling the differences

Energy Technology Data Exchange (ETDEWEB)

Wilkinson, J.G. [Alpine Geophysics, Pittsburgh, PA (United States); Emigh, R.A. [Alpine Geophysics, Boulder, CO (United States); Pierce, T.E. [Atmospheric Characterization and Modeling Division/NOAA, Research Triangle Park, NC (United States)

1996-12-31

Biogenic emissions play a critical role in urban and regional air quality. For instance, biogenic emissions contribute upwards of 76% of the daily hydrocarbon emissions in the Atlanta, Georgia airshed. The Biogenic Emissions Inventory System-Version 2.0 (BEIS2) and the Biogenic Model for Emissions (BIOME) are two models that compute biogenic emissions estimates. BEIS2 is a FORTRAN-based system, and BIOME is an ARC/INFO{reg_sign} - and SAS{reg_sign}-based system. Although the technical formulations of the models are similar, the models produce different biogenic emissions estimates for what appear to be essentially the same inputs. The goals of our study are the following: (1) Determine why BIOME and BEIS2 produce different emissions estimates; (2) Attempt to understand the impacts that the differences have on the emissions estimates; (3) Reconcile the differences where possible; and (4) Present a framework for the use of BEIS2 and BIOME. In this study, we used the Coastal Oxidant Assessment for Southeast Texas (COAST) biogenics data which were supplied to us courtesy of the Texas Natural Resource Conservation Commission (TNRCC), and we extracted the BEIS2 data for the same domain. We compared the emissions estimates of the two models using their respective data sets BIOME Using TNRCC data and BEIS2 using BEIS2 data.

Thin films of thermoelectric compound Mg2Sn deposited by co-sputtering assisted by multi-dipolar microwave plasma

International Nuclear Information System (INIS)

Le-Quoc, H.; Lacoste, A.; Hlil, E.K.; Bes, A.; Vinh, T. Tan; Fruchart, D.; Skryabina, N.

2011-01-01

Highlights: → Mg 2 Sn thin films deposited by plasma co-sputtering, on silicon and glass substrates. → Formation of nano-grained polycrystalline films on substrates at room temperature. → Structural properties vary with target biasing and target-substrate distance. → Formation of the hexagonal phase of Mg 2 Sn in certain deposition conditions. → Power factor ∼5.0 x 10 -3 W K -2 m -1 for stoichiometric Mg 2 Sn films doped with ∼1 at.% Ag. - Abstract: Magnesium stannide (Mg 2 Sn) thin films doped with Ag intended for thermoelectric applications are deposited on both silicon and glass substrates at room temperature by plasma assisted co-sputtering. Characterization by scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction confirms the formation of fine-grained polycrystalline thin films with thickness of 1-3 μm. Stoichiometry, microstructure and crystal structure of thin films are found to vary with target biasing and the distance from targets to substrate. Measurements of electrical resistivity and Seebeck coefficient at room temperature show the maximum power factor of ∼5.0 x 10 -3 W K -2 m -1 for stoichiometric Mg 2 Sn thin films doped with ∼1 at.% Ag.

Biogenic Emission Sources

Science.gov (United States)

Biogenic emissions sources come from natural sources and need to accounted for in photochemical grid models. They are computed using a model which utilizes spatial information on vegetation and land use.

Ice nuclei in marine air: biogenic particles or dust?

Directory of Open Access Journals (Sweden)

S. M. Burrows

2013-01-01

Full Text Available Ice nuclei impact clouds, but their sources and distribution in the atmosphere are still not well known. Particularly little attention has been paid to IN sources in marine environments, although evidence from field studies suggests that IN populations in remote marine regions may be dominated by primary biogenic particles associated with sea spray. In this exploratory model study, we aim to bring attention to this long-neglected topic and identify promising target regions for future field campaigns. We assess the likely global distribution of marine biogenic ice nuclei using a combination of historical observations, satellite data and model output. By comparing simulated marine biogenic immersion IN distributions and dust immersion IN distributions, we predict strong regional differences in the importance of marine biogenic IN relative to dust IN. Our analysis suggests that marine biogenic IN are most likely to play a dominant role in determining IN concentrations in near-surface-air over the Southern Ocean, so future field campaigns aimed at investigating marine biogenic IN should target that region. Climate-related changes in the abundance and emission of biogenic marine IN could affect marine cloud properties, thereby introducing previously unconsidered feedbacks that influence the hydrological cycle and the Earth's energy balance. Furthermore, marine biogenic IN may be an important aspect to consider in proposals for marine cloud brightening by artificial sea spray production.

Structural investigation of biogenic ferrihydrite nanoparticles dispersion

International Nuclear Information System (INIS)

Balasoiu, M.; Ishchenko, L.A.; Stolyar, S.V.; Iskhakov, R.S.; Rajkher, Yu.L.; Kuklin, A.I.; Solov'ev, D.V.; Arzumanyan, G.M.; Kurkin, T.S.; Aranghel, D.

2010-01-01

Structural properties of biogenic ferrihydrite nanoparticles produced by bacteria Klebsiella oxytoca are investigated. Investigations of morphology and size of particles dispersed in water by means of high-resolution transmission electron microscopy and small angle X-ray scattering measurements were performed. By model calculations followed by fitting procedure the structural parameters of a cylinder of radius R = (4.87 ± 0.02) nm and height L = (2.12 ± 0.04) nm are obtained

Enhancement of magnetoresistance by inserting thin NiAl layers at the interfaces in Co{sub 2}FeGa{sub 0.5}Ge{sub 0.5}/Ag/Co{sub 2}FeGa{sub 0.5}Ge{sub 0.5} current-perpendicular-to-plane pseudo spin valves

Energy Technology Data Exchange (ETDEWEB)

Jung, J. W.; Sakuraba, Y., E-mail: Sakuraba.Yuya@nims.go.jp; Sasaki, T. T.; Hono, K. [National Institute for Materials Science (NIMS), Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan); Miura, Y. [National Institute for Materials Science (NIMS), Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan); Kyoto Institute of Technology, Electrical Engineering and Electronics, Kyoto 606-8585 (Japan)

2016-03-07

We have investigated the effects of insertion of a thin NiAl layer (≤0.63 nm) into a Co{sub 2}FeGa{sub 0.5}Ge{sub 0.5} (CFGG)/Ag interface on the magnetoresistive properties in CFGG/Ag/CFGG current-perpendicular-to-plane giant magnetoresistance (CPP-GMR) pseudo spin valves (PSVs). First-principles calculations of ballistic transmittance clarified that the interfacial band matching at the (001)-oriented NiAl/CFGG interface is better than that at the (001)-Ag/CFGG interface. The insertion of 0.21-nm-thick NiAl layers at the Co{sub 2}FeGa{sub 0.5}Ge{sub 0.5}/Ag interfaces effectively improved the magnetoresistance (MR) output; the observed average and the highest MR ratio (ΔRA) are 62% (25 mΩ μm{sup 2}) and 77% (31 mΩ μm{sup 2}) at room temperature, respectively, which are much higher than those without NiAl insertion. Microstructural analysis using scanning transmission electron microscopy confirmed the existence of thin NiAl layers at the Ag interfaces with only modest interdiffusion even after annealing at 550 °C. The improvement of the interfacial spin-dependent scattering by very thin NiAl insertion can be a predominant reason for the enhancement of the MR output.

Liraglutide 3.0 mg for Weight Management: A Population Pharmacokinetic Analysis.

Science.gov (United States)

Overgaard, Rune V; Petri, Kristin C; Jacobsen, Lisbeth V; Jensen, Christine B

2016-11-01

This analysis used a population pharmacokinetic approach to identify covariates that influence plasma exposure of liraglutide 3.0 mg, a glucagon-like peptide-1 (GLP-1) receptor agonist approved for weight management in overweight and obese individuals. Samples for pharmacokinetic analysis were drawn at weeks 2, 12 and 28 of the phase IIIa SCALE Obesity and Prediabetes (N = 2339) and SCALE Diabetes (N = 584) trials. Dose proportionality of liraglutide in obese subjects was investigated using data from a phase II dose-finding study (N = 331). Dose-proportional exposure of liraglutide up to and including 3.0 mg was confirmed. Body weight and sex influenced exposure of liraglutide 3.0 mg, while age ≥70 years, race, ethnicity and baseline glycaemic status did not. Compared with a reference subject weighing 100 kg, exposure of liraglutide 3.0 mg was 44 % lower for a subject weighing 234 kg (90 % CI 41-47), 41 % higher for a subject weighing 60 kg (90 % CI 37-46), and 32 % higher (90 % CI 28-35) in females than males with the same body weight. Neither injection site nor renal function significantly influenced exposure of liraglutide 3.0 mg (post hoc analysis). Population pharmacokinetics of liraglutide up to and including 3.0 mg daily in overweight and obese adults demonstrated dose-proportional exposure, and limited effect of covariates other than sex and body weight. These findings were similar to those previously observed with liraglutide up to 1.8 mg in subjects with type 2 diabetes mellitus. Further analysis of exposure-response relationship and its effect on dose requirements is addressed in a separate publication.

Biogenic nanosilver incorporated reverse osmosis membrane for antibacterial and antifungal activities against selected pathogenic strains: an enhanced eco-friendly water disinfection approach.

Science.gov (United States)

Manjumeena, R; Duraibabu, D; Sudha, J; Kalaichelvan, P T

2014-01-01

Reverse osmosis (RO) membranes have been used extensively in water desalination plants, waste water treatment in industries, agricultural farms and drinking water production applications. The objective of this work is to impart antibacterial and antifungal activities to commercially available RO membrane used in water purification systems by incorporating biogenic silver nanoparticles(AgNPs) synthesized using Rosa indica wichuriana hybrid leaf extract. The morphology and surface topography of uncoated and AgNPs-coated RO membrane were studied using Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). Elemental composition of the AgNPs-coated RO membrane was analyzed by energy-dispersive X-ray spectroscopy (EDAX). The functional groups were identified by Fourier Transform Infrared spectroscopy (FT-IR). Hydrophilicity of the uncoated and AgNPs-coated RO membrane was analyzed using water contact angle measurements. The thermal properties were studied by thermogravimetric analysis (TGA). The AgNPs incorporated RO membrane exhibited good antibacterial and antifungal activities against pathogenic bacterial strains such as E. coli, S. aureus, M. luteus, K. pneumoniae, and P. aeruginosa and fungal strains such as Candida tropicalis, C. krusei, C. glabrata, and C. albicans.

Thickness dependence of J_c (0) in MgB_2 films

International Nuclear Information System (INIS)

Chen, Yiling; Yang, Can; Jia, Chunyan; Feng, Qingrong; Gan, Zizhao

2016-01-01

Highlights: • A serial of MgB_2 superconducting films from 10 nm to 8 µm have been prepared. • T_c and J_c (5 K, 0 T) of films are high. • J_c (5 K, 0 T) reaches its maximum 2.3 × 10"8 A cm"−"2 for 100 nm films. • The relationship between thickness and J_c has been discussed in detail. - Abstract: MgB_2 superconducting films, whose thicknesses range from 10 nm to 8 µm, have been fabricated on SiC substrates by hybrid physical–chemical vapor deposition (HPCVD) method. It is the first time that the T_c and the J_c of MgB_2 films are studied on such a large scale. It is found that with the increasing of thickness, T_c elevates first and then keeps roughly stable except for some slight fluctuations, while J_c (5 K, 0 T) experiences a sharp increase followed by a relatively slow fall. The maximum J_c (5 K, 0 T) = 2.3 × 10"8 A cm"−"2 is obtained for 100 nm films, which is the experimental evidence for preparing high-quality MgB_2 films by HPCVD method. Thus, this work may provide guidance on choosing the suitable thickness for applications. Meanwhile, the films prepared by us cover ultrathin films, thin films and thick films, so the study on them will bring a comprehensive understanding of MgB_2 films.

Local structure and thermoelectric properties of Mg{sub 2}Si{sub 0.977−x}Ge{sub x}Bi{sub 0.023} (0.1 ⩽ x ⩽ 0.4)

Energy Technology Data Exchange (ETDEWEB)

Farahi, Nader [Department of Chemistry and Waterloo Institute for Nanotechnology, University of Waterloo, Waterloo, ON N2L 3G1 (Canada); Prabhudev, Sagar; Botton, Gianluigi A. [Materials Science and Engineering Department, McMaster University, Hamilton, ON L8S 4L8 (Canada); Zhao, Jianbao; Tse, John S. [Department of Physics and Engineering Physics, University of Saskatchewan, Saskatoon, SK S7N 5E2 (Canada); Liu, Zhenxian [Geophysical Laboratory, Carnegie Institution of Washington, Washington, DC 20015 (United States); Salvador, James R. [General Motors Research & Development Center, Warren, MI 48090 (United States); Kleinke, Holger, E-mail: kleinke@uwaterloo.ca [Department of Chemistry and Waterloo Institute for Nanotechnology, University of Waterloo, Waterloo, ON N2L 3G1 (Canada)

2015-09-25

Highlights: • Incorporating Ge into Bi-doped Mg{sub 2}Si decreases the thermal conductivity and enhances the thermoelectric performance. • Ge-rich domains, identified via TEM, contribute to these changes. • Interstitial sites are in part filled with Mg atoms, as revealed via TEM. • Doping with Bi is advantageous over doping with Sb, resulting in an increase of 48% of the thermoelectric figure of merit. • The highest figure-of-merit of these materials is zT{sub max} = 0.7 at 773 K, realized for Mg{sub 2}Si{sub 0.677}Ge{sub 0.3}Bi{sub 0.023}. - Abstract: We investigated the effect of germanium substitution for silicon in bismuth doped Mg{sub 2}Si. This alloying reduces the thermal conductivity from above 7 W m{sup −1} K{sup −1} to 2.7 W m{sup −1} K{sup −1} at around 300 K in part due to the added mass contrast. High resolution transmission electron microscopy (HRTEM) revealed the presence of Ge-rich domains within the Mg{sub 2}(Si,Ge,Bi) particles, contributing to decreasing thermal conductivity with increasing Ge content up to 0.3 Ge per formula unit. The electrical conductivity also decreases with Ge alloying because of the increasing amount of scattering centers, while the Seebeck coefficient increased only very slightly. In total, the positive effect of Ge substitution on the thermoelectric properties of Bi doped Mg{sub 2}Si resulted in a figure of merit of 0.7 at 773 K for Mg{sub 2}Si{sub 0.677}Ge{sub 0.3}Bi{sub 0.023} sample. The optimum amount of Bi seems to be 0.023 per formula unit (0.77 at%), since lower Bi content resulted in electrical conductivity that is too low, and higher Bi content generated the Mg{sub 3}Bi{sub 2} intermetallic phase.

Effect of laser energy on the electrical transport properties of La{sub 0.67}Ca{sub 0.33}MnO{sub 3}:Ag{sub 0.2} films by pulsed laser deposition technique

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yalin; Chen, Qingming; Jin, Fei; Chen, Xiaohui; Li, Zhiyu; Li, Di; Zhang, Hui [Kunming University of Science and Technology, Faculty of Materials Science and Engineering, Kunming (China)

2017-09-15

La{sub 0.67}Ca{sub 0.33}MnO{sub 3} (LCMO):Ag{sub 0.2} films were grown on LaAlO{sub 3} (LAO) substrates (100) by pulsed laser deposition (PLD) technique with various incident laser energies. The surface morphologies and the thicknesses of the films were studied by atomic force microscopy (AFM) and scanning electron microscopy (SEM), respectively. The crystal structures were analyzed by X-ray, diffraction (XRD), and the temperature dependence of the resistivity (ρ-T) of the films was studied by the standard four-probe method. It can be found that the crystal quality, surface morphology, metal-insulator transition temperature (T{sub p}), and temperature coefficient of resistance (TCR) of the LCMO:Ag{sub 0.2} films are changed with various laser energy. The highest T{sub p} 287 K is obtained with 300 mJ laser energy; meanwhile, the optimal TCR 13.5% K{sup -1} is achieved. The results suggest that the electrical transport properties of LCMO:Ag{sub 0.2} films are affected by the interface-induced compressive stress, the oxygen balance, and the double exchange between Mn{sup 3+}-O-Mn{sup 4+}. (orig.)

Stable silicon isotope signatures of marine pore waters - Biogenic opal dissolution versus authigenic clay mineral formation

Science.gov (United States)

Ehlert, Claudia; Doering, Kristin; Wallmann, Klaus; Scholz, Florian; Sommer, Stefan; Grasse, Patricia; Geilert, Sonja; Frank, Martin

2016-10-01

Dissolved silicon isotope compositions have been analysed for the first time in pore waters (δ30SiPW) of three short sediment cores from the Peruvian margin upwelling region with distinctly different biogenic opal content in order to investigate silicon isotope fractionation behaviour during early diagenetic turnover of biogenic opal in marine sediments. The δ30SiPW varies between +1.1‰ and +1.9‰ with the highest values occurring in the uppermost part close to the sediment-water interface. These values are of the same order or higher than the δ30Si of the biogenic opal extracted from the same sediments (+0.3‰ to +1.2‰) and of the overlying bottom waters (+1.1‰ to +1.5‰). Together with dissolved silicic acid concentrations well below biogenic opal saturation, our collective observations are consistent with the formation of authigenic alumino-silicates from the dissolving biogenic opal. Using a numerical transport-reaction model we find that approximately 24% of the dissolving biogenic opal is re-precipitated in the sediments in the form of these authigenic phases at a relatively low precipitation rate of 56 μmol Si cm-2 yr-1. The fractionation factor between the precipitates and the pore waters is estimated at -2.0‰. Dissolved and solid cation concentrations further indicate that off Peru, where biogenic opal concentrations in the sediments are high, the availability of reactive terrigenous material is the limiting factor for the formation of authigenic alumino-silicate phases.

Discovery of the shape coexisting 0+ state in 32Mg

International Nuclear Information System (INIS)

Wimmer, Kathrin

2010-01-01

The evolution of shell structure in exotic nuclei as a function of proton (Z) and neutron (N) number is currently at the center of many theoretical and experimental investigations. It has been realized that the interaction of the last valence protons and neutrons, in particular the monopole component of the residual interaction between those nucleons, can lead to significant shifts in the single-particle energies, leading to the collapse of classic shell closures and the appearance of new shell gaps. The ''Island of Inversion'' around 32 Mg, which is one of the most studied phenomena in the nuclear chart, is a well known example for such changes in nuclear structure. In this region of neutron-rich nuclei around the magic number N=20 strongly deformed ground states in Ne, Na, and Mg isotopes have been observed. Due to the reduction of the N=20 shell gap quadrupole correlations can enable low-lying deformed 2p-2h intruder states from the fp-shell to compete with spherical normal neutron 0p-0h states of the sd-shell. In this situation the promotion of a neutron pair across the N=20 gap can result in deformed intruder ground states. Consequentially the two competing configurations can lead to the coexistence of spherical and deformed 0 + states in the neutron rich nuclei 30,32 Mg. In this work the shape coexistence in 32 Mg was studied by a two neutron transfer reaction at the REX-ISOLDE facility (CERN). The two neutron transfer reaction with a 30 Mg beam involved for the first time the use of a radioactive tritium target in combination with a radioactive heavy ion beam. Light charged particles emitted from the target were detected and identified by the T-REX particle detector while γ-rays were detected by the MINIBALL Germanium detector array. The shape of the angular distribution of the protons allows to unambiguously determine the angular momentum transfer ΔL of the reaction and thus to identify the 0 + states. The analysis of excitation energies and angular

Composite Ag-La0.8Sr0.2MnO3-σ Cathode for Solid Oxide Fuel Cells

Directory of Open Access Journals (Sweden)

Mosiałek M.

2013-12-01

Full Text Available Na powierzchni elektrolitu stałego wytwarzano kompozytowe katody dla stałotlenkowych ogniw paliwowych zbudowane z metalicznego srebra rozproszonego w osnowie z La0.8Sr0,3MnO3-σ Osnowę o kontrolowanej porowatości otrzymywano przez prażenie mieszaniny proszku La0.8Sr0.2MnO3-σ z kulkami z tworzywa organicznego. Porowatą osnowę nasycano roztworem AgNCb i ponownie wyprażano. Tak otrzymane katody wykazywały wyższą przewodność elektryczną i niższą oporność akty- wacyjną w reakcji redukcji tlenu w porównaniu z katodami z czystej ceramiki.

Electrochemical enzyme sensor arrays for the detection of the biogenic amines histamine, putrescine and cadaverine using magnetic beads as immobilisation supports

International Nuclear Information System (INIS)

Leonardo, Sandra; Campàs, Mònica

2016-01-01

Electrochemical biosensors based on diamine oxidase (DAO) conjugated to magnetic beads (MBs) were developed for the detection of histamine (Hist), putrescine (Put) and cadaverine (Cad), the most relevant biogenic amines (BAs) related to food safety and quality. DAO-MBs were immobilised on Co(II)-phthalocyanine/carbon and Prussian Blue/carbon electrodes to obtain mono-enzymatic biosensors, and on Os-wired HRP-modified carbon electrodes to obtain bi-enzymatic biosensors. The three sensor have low working potentials (+0.4 V, −0.1 V and −0.05 V vs Ag/AgCl, respectively), a linear range of two orders of magnitude (from 0.01 to 1 mM BA), good reproducibility (variability lower than 10 %), high repeatability (up to 8 consecutive measurements), limits of detection in the µM concentration range for Hist and in the sub-µM concentration range for Put and Cad, and no response from possible interfering compounds. The DAO-MB conjugates display excellent long-term stability (at least 3 months). The biosensor has been applied to the determination of BAs in spiked and naturally-spoiled fish, demonstrating its suitability both as screening tool and for BAs quantification. The use of MBs as supports for enzyme immobilisation is advantageous because the resulting biosensors are simple, fast, stable, affordable, and can be integrated into array platforms. This makes them suitable for high-throughput analysis of BAs in the food industry. (author)

Intolerance to dietary biogenic amines: A review

NARCIS (Netherlands)

Jansen, S.C.; Dusseldorp, M. van; Bottema, K.C.; Dubois, A.E.J.

2003-01-01

Objective: To evaluate the scientific evidence for purported intolerance to dietary biogenic amines. Data Sources: MEDLINE was searched for articles in the English language published between January 1966 and August 2001. The keyword biogenic amin* was combined with hypersens*, allerg*, intoler*, and

Intolerance to dietary biogenic amines : a review

NARCIS (Netherlands)

Jansen, SC; van Dusseldorp, M; Bottema, KC; Dubois, AEJ

Objective: To evaluate the scientific evidence for purported intolerance to dietary biogenic amines. Data Sources: MEDLINE was searched for articles in the English language published between January 1966 and August 2001. The keyword biogenic amin* was combined with hypersens*, allergen intoler*, and

Radiation portal monitor with "1"0B+ZnS(Ag) neutron detector performance for the detection of special nuclear materials

International Nuclear Information System (INIS)

Guzman G, K. A.; Gallego, E.; Lorente, A.; Ibanez F, S.; Vega C, H. R.; Gonzalez, J. A.; Mendez, R.

2016-10-01

In homeland security, neutron detection is used to prevent the smuggling of special nuclear materials. Thermal neutrons are normally detected with "3He proportional counters, in the radiation portal monitors, Rpms, however due to the "3He shortage new procedures are being studied. In this work Monte Carlo methods, using the MCNP6 code, have been used to study the neutron detection features of a "1"0B+ZnS(Ag) under real conditions inside of a Rpm. The performance for neutron detection was carried out for "2"5"2Cf, "2"3"8U and "2"3"9Pu under different conditions. In order to mimic an actual situation occurring at border areas, a sample of SNM sited inside a vehicle was simulated and the Rpm with "1"0B+ZnS(Ag) response was calculated. At 200 cm the "1"0B+ZnS(Ag) on Rpm response is close to 2.5 cps-ng "2"5"2Cf, when the "2"5"2Cf neutron source is shielded with 0.5 cm-thick lead and 2.5 cm-thick polyethylene fulfilling the ANSI recommendations. Three different geometries of neutron detectors of "1"0B+ZnS(Ag) in a neutron detection system in Rpm were modeled. Therefore, the "1"0B+ZnS(Ag) detectors are an innovative and viable replacement for the "3He detectors in the Rpm. (Author)

Effects of silver nanoparticle (Ag NP on oxidative stress biomarkers in rat

Directory of Open Access Journals (Sweden)

Akram Ranjbar

2014-04-01

Full Text Available Objective(s: Nanotechnology and nanoparticles are increasingly recognized for their potential applications in aerospace engineering, nanoelectronics, and environmental remediation, medicine and consumer products. More importantly is the potential for the application of silver nanoparticles (Ag NPs in the treatment of diseases that require maintenance of circulating drug concentration or targeting of specific cells or organs the aim of this study was to investigate the possible protective role of Ag NP antioxidative biomarkers in rats. Ag NPs are used to investigate the potential risks for the environment and health. Materials and Methods: Rats received Ag NP, 5, 50, 250 and 500 mg/kg/day IP. After two week of treatment, the activity of enzymatic scavengers such as glutathione peroxidase (GPx, superoxide dismutase (SOD and total antioxidant capacity (TAC of blood samples were measured. Results: Ag NP in 5, 50, 250 and 500 mg/kg reduced activities of CAT, SOD and increased TAC in plasma. Conclusion: In this study, Ag NP with 500mg/kg induced activities of CAT, SOD and decreased TAC. It is concluded that antioxidative properties of Ag NP is dose dependent.

Synthesis and characterization of Cu0.3Zn0.5Mg0.2Fe2O4 nanoparticles as a magnetic drug delivery system

Science.gov (United States)

Ansari, Mohammad; Bigham, Ashkan; Hassanzadeh-Tabrizi, S. A.; Abbastabar Ahangar, H.

2017-10-01

Mixed spinel ferrite nanoparticles are being applied in biomedical applications due to their biocompatibility, antibacterial activity, particular magnetic and electronic properties with chemical and thermal stabilities. The Cu0.3Zn0.5Mg0.2Fe2O4 nanoparticles are synthesized through the thermal treatment method. Polyvinyl alcohol (PVA) is used as the capping agent to stabilize the particles and prevent their agglomeration. The synthesized nanoparticles are characterized through X-ray diffractometer (XRD), Fourier transform infrared spectroscopy (FTIR), N2 adsorption-desorption, field emission scanning electron microscopy (FESEM), and transmission electron microscope (TEM). The magnetic characterization is made on a vibrating sample magnetometer (VSM), which displayed super-paramagnetic behavior of the synthesized sample. Potential application of the Cu0.3Zn0.5Mg0.2Fe2O4 nanoparticles as a drug delivery agent is assessed in vitro by estimating their release properties. The obtained results indicate that the amount of ibuprofen (IBU) adsorbed into the nanocarrier of Cu0.3Zn0.5Mg0.2Fe2O4 is 104 mg/g and the drug release is sustained up to 72 h.

Preparation and Characterization of γ-AgI in Superionic Composite Glasses (AgIx(AgPO31-x

Directory of Open Access Journals (Sweden)

S. Suminta

2007-07-01

Full Text Available The γ-AgI phase was stabilized at room temperature in the composites glasses (AgIx(AgPO31-x with x = 0.6 and 0.7 via rapid quenching of their molten mixture. The measurement of the crystal structure has been carried out using an X-ray Difractometer at the Physics Departement of Ibaraki University, Japan. The micro strain and crystal size are derived from Hall’s equation. The X-ray diffraction pattern shows some Bragg peaks that correspond to the crystalline γ-AgI. By increasing the concentration of AgI, the peak width becomes more narrow and the position shifts to the higher angle. This indicates that the crystalline size and microstrain are increasing. The increase of micro strain (η, and particle size (D will increase the ionic mobility, thus increasing the ionic conductivity. It is concluded that solidification process on melt AgI into glass matrix AgPO3 not only decreases the micro strain and the particle size, but it also increases the ionic conductivity.

An Estimate of Biogenic Emissions of Volatile Organic Compounds during Summertime in China (7 pp).

Science.gov (United States)

Heinrich, Almut

2007-01-01

and Aim. An accurate estimation of biogenic emissions of VOC (volatile organic compounds) is necessary for better understanding a series of current environmental problems such as summertime smog and global climate change. However, very limited studies have been reported on such emissions in China. The aim of this paper is to present an estimate of biogenic VOC emissions during summertime in China, and discuss its uncertainties and potential areas for further investigations. This study was mainly based on field data and related research available so far in China and abroad, including distributions of land use and vegetations, biomass densities and emission potentials. VOC were grouped into isoprene, monoterpenes and other VOC (OVOC). Emission potentials of forests were determined for 22 genera or species, and then assigned to 33 forest ecosystems. The NCEP/NCAR reanalysis database was used as standard environmental conditions. A typical summertime of July 1999 was chosen for detailed calculations. The biogenic VOC emissions in China in July were estimated to be 2.3×1012gC, with 42% as isoprene, 19% as monoterpenes and 39% as OVOC. About 77.3% of the emissions are generated from forests and woodlands. The averaged emission intensity was 4.11 mgC m-2 hr-1 for forests and 1.12 mgC m-2 hr-1 for all types of vegetations in China during the summertime. The uncertainty in the results arose from both the data and the assumptions used in the extrapolations. Generally, uncertainty in the field measurements is relatively small. A large part of the uncertainty mainly comes from the taxonomic method to assign emission potentials to unmeasured species, while the ARGR method serves to estimate leaf biomass and the emission algorithms to describe light and temperature dependence. This study describes a picture of the biogenic VOC emissions during summertime in China. Due to the uneven spatial and temporal distributions, biogenic VOC emissions may play an important role in the

Hydrothermal, biogenic, and seawater components in metalliferous black shales of the Brooks Range, Alaska: Synsedimentary metal enrichment in a carbonate ramp setting

Science.gov (United States)

Slack, John F.; Selby, David; Dumoulin, Julie A.

2015-01-01

Trace element and Os isotope data for Lisburne Group metalliferous black shales of Middle Mississippian (early Chesterian) age in the Brooks Range of northern Alaska suggest that metals were sourced chiefly from local seawater (including biogenic detritus) but also from externally derived hydrothermal fluids. These black shales are interbedded with phosphorites and limestones in sequences 3 to 35 m thick; deposition occurred mainly on a carbonate ramp during intermittent upwelling under varying redox conditions, from suboxic to anoxic to sulfidic. Deposition of the black shales at ~335 Ma was broadly contemporaneous with sulfide mineralization in the Red Dog and Drenchwater Zn-Pb-Ag deposits, which formed in a distal marginal basin.Relative to the composition of average black shale, the metalliferous black shales (n = 29) display large average enrichment factors (>10) for Zn (10.1), Cd (11.0), and Ag (20.1). Small enrichments (>2–rare earth elements except Ce, Nd, and Sm. A detailed stratigraphic profile over 23 m in the Skimo Creek area (central Brooks Range) indicates that samples from at and near the top of the section, which accumulated during a period of major upwelling and is broadly correlative with the stratigraphic levels of the Red Dog and Drenchwater Zn-Pb-Ag deposits, have the highest Zn/TOC (total organic carbon), Cu/TOC, and Tl/TOC ratios for calculated marine fractions (no detrital component) of these three metals.Average authigenic (detrital-free) contents of Mo, V, U, Ni, Cu, Cd, Pb, Ge, Re, Se, As, Sb, Tl, Pd, and Au show enrichment factors of 4.3 × 103 to 1.2 × 106 relative to modern seawater. Such moderate enrichments, which are common in other metalliferous black shales, suggest wholly marine sources (seawater and biogenic material) for these metals, given similar trends for enrichment factors in organic-rich sediments of modern upwelling zones on the Namibian, Peruvian, and Chilean shelves. The largest enrichment factors for Zn and Ag

Evolution of Mg-5Al-0.4Mn microstructure after rare earth elements addition

Directory of Open Access Journals (Sweden)

A. Żydek

2011-04-01

Full Text Available Mg-5Al-0.4Mn-xRE (x = 0, 1, 2, 3 wt.% magnesium alloys were prepared successfully by casting method. The microstructure wasinvestigated by light microscopy. The influence of rare earth (RE elements on the area fraction of eutectic was analysed. The obtainedresults revealed that the as-cast Mg-5Al-0.4Mn alloy consist of α - Mg matrix and eutectic α + γ (where γ is Mg17Al12. However, whilerare earth elements were added to the Mg-Al type alloy, Al11RE3 precipitates were formed. The amount of the Al11RE3 precipitatesincreased with increasing addition of RE, but the amount of γ - Mg17Al12 decreased.

20% Efficient Zn0.9Mg0.1O:Al/Zn0.8Mg0.2O/Cu(In,Ga)(S,Se)2 Solar Cell Prepared by All-Dry Process through a Combination of Heat-Light-Soaking and Light-Soaking Processes.

Science.gov (United States)

Chantana, Jakapan; Kato, Takuya; Sugimoto, Hiroki; Minemoto, Takashi

2018-04-04

Development of Cd-free Cu(In,Ga)(S,Se) 2 (CIGSSe)-based thin-film solar cells fabricated by an all-dry process is intriguing to minimize optical loss at a wavelength shorter than 520 nm owing to absorption of the CdS buffer layer and to be easily integrated into an in-line process for cost reduction. Cd-free CIGSSe solar cells are therefore prepared by the all-dry process with a structure of Zn 0.9 Mg 0.1 O:Al/Zn 0.8 Mg 0.2 O/CIGSSe/Mo/glass. It is demonstrated that Zn 0.8 Mg 0.2 O and Zn 0.9 Mg 0.1 O:Al are appropriate as buffer and transparent conductive oxide layers with large optical band gap energy values of 3.75 and 3.80 eV, respectively. The conversion efficiency (η) of the Cd-free CIGSSe solar cell without K-treatment is consequently increased to 18.1%. To further increase the η, the Cd-free CIGSSe solar cell with K-treatment is next fabricated and followed by posttreatment called the heat-light-soaking (HLS) + light-soaking (LS) process, including HLS at 110 °C followed by LS under AM 1.5G illumination. It is disclosed that the HLS + LS process gives rise to not only the enhancement of carrier density but also the decrease in the carrier recombination rate at the buffer/absorber interface. Ultimately, the η of the Cd-free CIGSSe solar cell with K-treatment prepared by the all-dry process is enhanced to the level of 20.0%.

Biogenic synthesis and spectroscopic characterization of silver nanoparticles using leaf extract of Indoneesiella echioides: in vitro assessment on antioxidant, antimicrobial and cytotoxicity potential

Science.gov (United States)

Kuppurangan, Gunaseelan; Karuppasamy, Balaji; Nagarajan, Kanipandian; Krishnasamy Sekar, Rajkumar; Viswaprakash, Nilmini; Ramasamy, Thirumurugan

2016-10-01

Natural synthesis of metal nanoparticles is gaining more attention in recent years. This article demonstrates the phytochemical synthesis of silver nanoparticles (AgNPs) by using Indoneesiella echioides (L) leaf extract as a reducing and stabilizing agent. Biosynthesis of AgNPs was monitored by UV-visible spectroscopy which revealed intense surface plasmon resonance bands at 420 nm. Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction were employed to identify various functional groups and crystalline nature of AgNPs. High-resolution transmission electron microscopy studies demonstrated that synthesized particles were spherical with average size of ~29 nm. In vitro antioxidant effects were analyzed by 2,2'-Azino-bis-(3-ethylbenzothiazoline-6-sulfonic acid) diammonium salt (ABTS) and 2,2-diphenyl-1-picrylhydrazyl (DPPH), which exhibited 69 and 71 % of scavenging activity, respectively. The antimicrobial activity of green AgNPs displayed better zone of inhibition against selected human pathogens. The present study also investigated the toxicity effect of biogenic AgNPs against human lung adenocarcinoma cancer cells (A549) and normal human epithelial cells (HBL-100) in vitro, and the inhibitory concentrations (IC50) were found to be 30 and 60 µg/mL, respectively. Herein, we propose a previously unexplored medicinal plant for the biological synthesis of AgNPs with potent biomedical applications.

Exposure-response analyses of liraglutide 3.0 mg for weight management.

Science.gov (United States)

Wilding, J P H; Overgaard, R V; Jacobsen, L V; Jensen, C B; le Roux, C W

2016-05-01

Liraglutide 3.0 mg, an acylated GLP-1 analogue approved for weight management, lowers body weight through decreased energy intake. We conducted exposure-response analyses to provide important information on individual responses to given drug doses, reflecting inter-individual variations in drug metabolism, absorption and excretion. We report efficacy and safety responses across a wide range of exposure levels, using data from one phase II (liraglutide doses 1.2, 1.8, 2.4 and 3.0 mg), and two phase IIIa [SCALE Obesity and Prediabetes (3.0 mg); SCALE Diabetes (1.8; 3.0 mg)] randomized, placebo-controlled trials (n = 4372). There was a clear exposure-weight loss response. Weight loss increased with greater exposure and appeared to level off at the highest exposures associated with liraglutide 3.0 mg in most individuals, but did not fully plateau in men. In individuals with overweight/obesity and comorbid type 2 diabetes, there was a clear exposure-glycated haemoglobin (HbA1c) relationship. HbA1c reduction increased with higher plasma liraglutide concentration (plateauing at ∼21 nM); however, for individuals with baseline HbA1c >8.5%, HbA1c reduction did not fully plateau. No exposure-response relationship was identified for any safety outcome, with the exception of gastrointestinal adverse events (AEs). Individuals with gallbladder AEs, acute pancreatitis or malignant/breast/benign colorectal neoplasms did not have higher liraglutide exposure compared with the overall population. These analyses support the use of liraglutide 3.0 mg for weight management in all subgroups investigated; weight loss increased with higher drug exposure, with no concomitant deterioration in safety/tolerability besides previously known gastrointestinal side effects. © 2016 John Wiley & Sons Ltd.

Exposure–response analyses of liraglutide 3.0 mg for weight management

Science.gov (United States)

Overgaard, R. V.; Jacobsen, L. V.; Jensen, C. B.; le Roux, C. W.

2016-01-01

Aims Liraglutide 3.0 mg, an acylated GLP‐1 analogue approved for weight management, lowers body weight through decreased energy intake. We conducted exposure‐response analyses to provide important information on individual responses to given drug doses, reflecting inter‐individual variations in drug metabolism, absorption and excretion. Methods We report efficacy and safety responses across a wide range of exposure levels, using data from one phase II (liraglutide doses 1.2, 1.8, 2.4 and 3.0 mg), and two phase IIIa [SCALE Obesity and Prediabetes (3.0 mg); SCALE Diabetes (1.8; 3.0 mg)] randomized, placebo‐controlled trials (n = 4372). Results There was a clear exposure–weight loss response. Weight loss increased with greater exposure and appeared to level off at the highest exposures associated with liraglutide 3.0 mg in most individuals, but did not fully plateau in men. In individuals with overweight/obesity and comorbid type 2 diabetes, there was a clear exposure–glycated haemoglobin (HbA1c) relationship. HbA1c reduction increased with higher plasma liraglutide concentration (plateauing at ∼21 nM); however, for individuals with baseline HbA1c >8.5%, HbA1c reduction did not fully plateau. No exposure–response relationship was identified for any safety outcome, with the exception of gastrointestinal adverse events (AEs). Individuals with gallbladder AEs, acute pancreatitis or malignant/breast/benign colorectal neoplasms did not have higher liraglutide exposure compared with the overall population. Conclusions These analyses support the use of liraglutide 3.0 mg for weight management in all subgroups investigated; weight loss increased with higher drug exposure, with no concomitant deterioration in safety/tolerability besides previously known gastrointestinal side effects. PMID:26833744

The microstructures and electrochemical performances of La0.6Gd0.2Mg0.2Ni3.0Co0.5-xAlx (x=0-0.5) hydrogen storage alloys as negative electrodes for nickel/metal hydride secondary batteries

Science.gov (United States)

Li, Rongfeng; Xu, Peizhen; Zhao, Yamin; Wan, Jing; Liu, Xiaofang; Yu, Ronghai

2014-12-01

La0.6Gd0.2Mg0.2Ni3.0Co0.5-xAlx (x = 0-0.5) hydrogen storage alloys were prepared by induction melting followed by annealing treatment at 1173 K for 8 h. The effects of substitution Al for Co on the microstructures and electrochemical performances were studied systematically. The structure analyses show that all alloys consist of multiphase structures such as (La, Mg)2Ni7 phase, (La, Mg) Ni3 phase and LaNi5 phase. The abundance of (La, Mg)2Ni7 phase decreases while the abundance of LaNi5 phase and (La, Mg)Ni3 phase increases directly as the Al content increasing. The electrochemical tests show that the maximum discharge capacity of alloy electrodes are almost unchanged when x ≤ 0.2 while the cyclic stability of the alloy electrode are improved significantly after proper amount of Al substitution for Co. The alloy electrode with x = 0.1 exhibits the better balance between discharge capacity and cycling life than any others. Moreover, at the discharge current density of 900 mA g-1, the high rate dischargeability (HRD) of the alloy electrodes decreases with increasing Al substitution and the relative analyses reveal that the charge transfer on alloy surface is more important than the hydrogen diffusion in alloy bulk for the kinetic properties of the alloy electrodes.

Structural and physical properties of Mg3-xZnxSb2 (x=0-1.34)

International Nuclear Information System (INIS)

Ahmadpour, Faraz; Kolodiazhnyi, Taras; Mozharivskyj, Yurij

2007-01-01

The Mg 3-x Zn x Sb 2 phases with x=0-1.34 were prepared by direct reactions of the elements in tantalum tubes. According to the X-ray single crystal and powder diffraction, the Mg 3-x Zn x Sb 2 phases crystallize in the same P3-bar m1 space group as the parent Mg 3 Sb 2 phase. The Mg 3-x Zn x Sb 2 structure is different from the other substituted structures of Mg 3 Sb 2 , such as (Ca, Sr, Ba) Mg 2 Sb 2 or Mg 5.23 Sm 0.77 Sb 4 , in a way that in Mg 3-x Zn x Sb 2 the Mg atoms on the tetrahedral sites are replaced, while in the other structures Mg on the octahedral sites is replaced. Thermoelectric performance for the two members of the series, Mg 3 Sb 2 and Mg 2.36 Zn 0.64 Sb 2 , was evaluated from low to room temperatures through resistivity, Seebeck coefficient and thermal conductivity measurements. In contrast to Mg 3 Sb 2 which is a semiconductor, Mg 2.36 Zn 0.64 Sb 2 is metallic and exhibits an 18-times larger dimensionless figure-of-merit, ZT, at room temperature. However, thermoelectric performance of Mg 2.36 Zn 0.64 Sb 2 is still poor and it is mostly due to its large electrical resistivity. - Graphical abstract: The Mg atoms in Mg 3 Sb 2 were successfully substituted with Zn, with Zn going exclusively into the tetrahedral sites. Zn substitution increases the electrical conductivity in Mg 2.36 Zn 0.64 Sb 2 by closing the band gap. This change combined with a decrease in the thermal conductivity improves the ZT value

On the image of AGS ³He²⁺ $\\vec{n}$₀ in the blue

Energy Technology Data Exchange (ETDEWEB)

Meot, F. [Brookhaven National Lab. (BNL), Upton, NY (United States); Huang, H. [Brookhaven National Lab. (BNL), Upton, NY (United States); Tsoupas, N. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2015-03-01

This note addresses the transport of Helion spin $\\vec{n}$₀ vector, from its periodic orientation in the AGS to RHIC Blue ring injection kicker, via the AGS extraction system and the AtR line. The goal is to investigate optimal injection energy into RHIC, in the matter of Helion spin matching, in the hypothesis of equal warm and cold snake strengths in the AGS. The study uses recently computed OPERA 3-D field maps of the AGS cold snake, including possibility of independent solenoid and helix settings (as discussed in Tech. Note C-A/AP/485), together with the machinery of the AGS and AtR models developed in the stepwise ray-tracing code Zgoubi. Computing tools and methods employed are discussed as well, in order to facilitate possible further checks or investigations. They are however similar to those used in an earlier study regarding the image in RHIC Blue and Yellow of AGS $\\vec{n}$₀ via the AtR in the case of proton beam (Tech. Note C-A/AP/502), which can be referred to for additional details.

Evaluation of antibacterial properties on polysulfone composite membranes using synthesized biogenic silver nanoparticles with Ulva compressa (L.) Kütz. and Cladophora glomerata (L.) Kütz. extracts.

Science.gov (United States)

Minhas, Fozia T; Arslan, Gulsin; Gubbuk, I Hilal; Akkoz, Cengiz; Ozturk, Betul Yılmaz; Asıkkutlu, Baran; Arslan, Ugur; Ersoz, Mustafa

2018-02-01

Polysulfone (PS) composite membrane using green synthesized biogenic silver nanoparticles (Ag-NPs) with Ulva compressa (L.) Kütz. and Cladophora glomerata (L.) Kütz. extract were prepared by spin coating technique and are tested for antimicrobial activity using a direct contact test for the first time. Initially green synthesis of Ag-NPs was accomplished utilizing green macro algae i.e. U. compressa (L.) Kütz. and C. glomerata (L.) Kütz. by the reduction of AgNO 3 . The Ag-NPs/PS composite membranes from both algae revealed outstanding antimicrobial activity against all bacteria i.e. K. pneumonia, P. aeruginasa, E. coli, E. faecium and S. aureus. Bacterial growth was monitored for 17h with a temperature controlled microplate spectrophotometer. The kinetics of the outgrowth in each well were recorded continuously at 630nm every 60min. Thus present work remarkably offers a feasible, cheap and efficient alternative for making Ag-NPs and their utilization as antimicrobial agent on the PS composite membrane. Copyright © 2017 Elsevier B.V. All rights reserved.

Framework for Assessing Biogenic CO2 Emissions from Stationary Sources

Science.gov (United States)

This revision of the 2011 report, Accounting Framework for Biogenic CO2 Emissions from Stationary Sources, evaluates biogenic CO2 emissions from stationary sources, including a detailed study of the scientific and technical issues associated with assessing biogenic carbon dioxide...

Sugammadex 4.0 mg kg-1 reversal of deep rocuronium-induced neuromuscular blockade

DEFF Research Database (Denmark)

Yu, Buwei; Wang, Xiangrui; Hansen, Søren Helbo

2014-01-01

Objective: Maintenance of deep Neuro Muscular Blockade (NMB) until the end of surgery may be beneficial in some surgical procedures. The selective relaxant binding agent sugammadex rapidly reverses deep levels of rocuronium-induced NMB. The purpose of this study was to evaluate the efficacy...... and safety of sugammadex 4.0 mg kg-1 for reversal of deep rocuronium-induced NMB in Chinese and Caucasian patients. Methods: This was an open-label, multicenter, prospective Phase III efficacy study in adult American Society of Anesthesiologists Class 1-3 patients scheduled for surgery under general...... anesthesia and requiring deep NMB. All patients received intravenous propofol and opioids for induction and maintenance of anesthesia, and a single intubation dose of rocuronium 0.6 mg/kg, with maintenance doses of 0.1-0.2 mg/kg as required. Sugammadex 4.0 mg/kg was administered after the last dose...

BIOGENIC AMINES CONTENT IN SELECTED WINES DURING WINEMAKING

Directory of Open Access Journals (Sweden)

Radka Flasarová

2012-02-01

Full Text Available The aim of this study was to describe the development of selected biogenic amines (histamine; tyramine; phenylethylamine; putrescine; agmatine; and cadaverine during the winemaking in 10 selected species grown in Central Europe in 2008. The analysis was performed using ion-exchange chromatography by the sodium-citrate buffers with the post-column ninhydrin derivatization and photometric detection. A comparison of the content of biogenic amines in red and wine varieties showed that red wines have higher concentrations of biogenic amines.

Effect of Intermetallic on Electromigration and Atomic Diffusion in Cu/SnAg3.0Cu0.5/Cu Joints: Experimental and First-Principles Study

Science.gov (United States)

Zhou, Wei; Liu, Lijuan; Li, Baoling; Wu, Ping

2009-06-01

Electromigration phenomena in a one-dimensional Cu/SnAg3.0Cu0.5/Cu joint were investigated with current stressing. The special effect of intermetallic compound (IMC) layers on the formation of serious electromigration damage induced by nonuniform current density distribution was discussed based on experimental results. Meanwhile, hillocks were observed both at the anode and near the cathode of the joint, and they were described as the result of diffusion of atoms and compressive stress released along grain boundaries to the relatively free surface. Moreover, the diffusion behavior of Cu at the cathode was analyzed with the electromigration equation, and the stability of Ag atoms in the solder during electromigration was evaluated with a first-principles method.

Synthesis of silver nanoparticles deposited on silica by γ-irradiation and preparation of PE/Ag nano compound masterbatches

Science.gov (United States)

Nguyen, Thi Kim Lan; Trinh Nguyen, Thuy Ai; Phu Dang, Van; Duy Nguyen, Ngoc; Le, Anh Quoc; Hien Nguyen, Quoc

2013-12-01

Silver nanoparticles (AgNPs) deposited on silica were synthesized by gamma Co-60 irradiation of Ag+ dispersion in silica/ethanol/water mixture (9/80/20:w/v/v). The reduction of Ag+ is occurred by hydrated electron (e-aq) and hydrogen atom (H•) generated during radiolysis of ethanol/water. The conversion doses (Ag+ → Ag0) were determined by UV-Vis spectroscopy. The synthesized AgNPs/silica were characterized by transmission electron microscopy (TEM) and x-ray diffraction (XRD), which showed the size of AgNPs to be in the range of 5-40 nm for Ag+ concentrations from 5 to 20 mM. Masterbatches of PE/AgNPs/silica compound with silver content from 250 to 1000 mg kg-1 were also prepared. These masterbatches can be suitably used for various applications such as antimicrobial food containers and packing films, etc.

Precipitation in an Al–Mg–Cu alloy and the effect of a low amount of Ag

Energy Technology Data Exchange (ETDEWEB)

Mihara, Mami, E-mail: mihara.m.aa@m.titech.ac.jp [Department of Metallurgy and Ceramics Science, Tokyo Institute of Technology, Tokyo 152-8552 (Japan); Marioara, Calin D., E-mail: Calin.D.Marioara@sintef.no [SINTEF Materials and Chemistry, N-7465 Trondheim (Norway); Andersen, Sigmund J., E-mail: Sigmund.J.Andersen@sintef.no [SINTEF Materials and Chemistry, N-7465 Trondheim (Norway); Holmestad, Randi, E-mail: randi.holmestad@ntnu.no [Faculty of Physics, Norwegian University of Science and Technology, N-7491 Trondheim (Norway); Kobayashi, Equo, E-mail: equo@mtl.titech.ac.jp [Department of Metallurgy and Ceramics Science, Tokyo Institute of Technology, Tokyo 152-8552 (Japan); Sato, Tatsuo, E-mail: sato.tatsuo8@gmail.com [Precision and Intelligence Laboratory, Tokyo Institute of Technology, Yokohama 226-8503 (Japan)

2016-03-21

Two high-purity aluminium alloys based on composition Al–3.0Mg–1.0Cu (wt%), one with added 0.4 wt% Ag, were compared up to 11 days ageing at 443 K by means of transmission electron microscopy and hardness measurements. The base alloy exhibits an inhomogeneous precipitate microstructure with a high density of fine needle-shaped Guinier-Preston-Bagaryatsky (GPB) zones together with coarser precipitates of S′-Al{sub 2}CuMg and rods of the structurally unknown Z-phase. The S′ phase is preferably formed on dislocations. The addition of Ag has a strong effect, leading to a homogeneous distribution with fine Ag-containing icosahedral quasi-crystalline precipitates (iQC). Both the GPB zones in the base alloy and the iQC phase in the Ag added alloy survive even after long term ageing. Ag is found to suppress the formation of the S′ phase. It is suggested that the Z phase is an approximation phase to the quasi-crystalline phase as is the case for the T-phase, implying they are based on similar (Bergman) clusters.

Partial substitution of Zn Effects on the Structural and Electrical Properties of High Temperature Hg0.95Ag0.05Ba2Ca2Cu3O8+δ Superconductors

Science.gov (United States)

Abed, Noor S.; Fathi, Sabah J.; Jassim, Kareem A.; Mahdi, Shatha H.

2018-05-01

The effect of the Ag partial substitution at Hg site in HgOδ layer and Zn partial substitution at Ca site in CaO layer on the structure,Tc,electrical properties, and oxygen content for Hg-1223 have been studied. Bulk polycrystalline Hg1-xAgxBa2Ca2-yZnyCu3O8+δ compound samples with x=0.05 and y=0.0, 0.05, 0.1, 0.15, 0.2, 0.25, and 0.3, are synthesized by a solid state reaction process. Structural properties are studied by using X-ray powder pattern, the high temperature phase superconductor (Hg-1223) of the tetragonal structure didn't change with the partial substitution of Zn and Ag ions, lattice parameters c,c/a are established to vary with Ag and Zn- substitution. The surface morphology has been studied by using atomic force microscopes (AFM), showed that all specimens have good crystalline and homogeneous surface. Also give a best nano size value is 75.72 nm at x=0.05 and y=0.3. Four probe technique is used to measure Tc. The Tc were found to be increases from 129 K to 147 K and oxygen content were found to be increases with increasing Zn. In addition, dielectric properties (dielectric constant, dielectric loss factor, and the alternating electrical conductivity) are characterized directly by relating with Ag and Zn concentration.

Laponite Na+0.7[(Si8Mg5.5Li0.3)O20(OH)4]–0.7

Indian Academy of Sciences (India)

Si8Mg5.5Li0.3)O20(OH)4]–0.7. Negative charges are counterbalanced by Na+ ions present in the interlayer. Electrostatic screening length at pH 10 ≈30 nm. Effective maximum volume increases by a factor of 60. Thus, for less than 1 volume ...

Enhanced photocatalytic activity and characterization of magnetic Ag/BiOI/ZnFe2O4 composites for Hg0 removal under fluorescent light irradiation

Science.gov (United States)

Li, Chengwei; Zhang, Anchao; Zhang, Lixiang; Song, Jun; Su, Sheng; Sun, Zhijun; Xiang, Jun

2018-03-01

A series of magnetic Ag/BiOI/ZnFe2O4 hybrids synthesized via hydrothermal process, subsequent deposition-precipitation and photoreduction method were employed to remove elemental mercury (Hg0) under fluorescent light irradiation. The effects of Ag content, fluorescent light irradiation, reaction temperature, pH value, flue gas composition, anions and photocatalyst dosage on Hg0 removal were investigated in detail. The as-synthesized photocatalysts were characterized using N2 adsorption-desorption, XRD, SEM, TEM, HRTEM, XPS, VSM, DRS, ESR, PL and photocurrent response. The results showed that the ternary Ag/BiOI/ZnFe2O4 hybrids possessed enhanced visible-light-responsive photocatalytic performances for Hg0 removal. Ag/BiOI/ZnFe2O4 photocatalyst could be easily recovered from the reaction solution by an extra magnet and was stable in the process of Hg0 removal. Lower content of Ag was highly dispersed on the surface of BiOI/ZnFe2O4, while higher content of Ag would result in some aggregations and/or the blockages of micropore. In comparison to BiOI/ZnFe2O4, Ag deposited BiOI/ZnFe2O4 material showed lower recombination rate of electron-hole pairs. The superior Hg0 oxidation removal could correspond to good match of BiOI and ZnFe2O4, excellent fluidity and surface plasmon resonance effect of Ag0 nanoparticles, which led to higher separation efficiency of photogenerated electrons and holes, thereby enhancing the hybrids' photocatalytic activity.

The ABAG biogenic emissions inventory project

Science.gov (United States)

Carson-Henry, C. (Editor)

1982-01-01

The ability to identify the role of biogenic hydrocarbon emissions in contributing to overall ozone production in the Bay Area, and to identify the significance of that role, were investigated in a joint project of the Association of Bay Area Governments (ABAG) and NASA/Ames Research Center. Ozone, which is produced when nitrogen oxides and hydrocarbons combine in the presence of sunlight, is a primary factor in air quality planning. In investigating the role of biogenic emissions, this project employed a pre-existing land cover classification to define areal extent of land cover types. Emission factors were then derived for those cover types. The land cover data and emission factors were integrated into an existing geographic information system, where they were combined to form a Biogenic Hydrocarbon Emissions Inventory. The emissions inventory information was then integrated into an existing photochemical dispersion model.

Oxygen permeation properties of dense Bi1.5Er0.5O3-Ag cermet membranes

NARCIS (Netherlands)

ten Elshof, Johan E.; Nguyen, N.Q.; den Otter, M.W.; Bouwmeester, Henricus J.M.

1997-01-01

Oxygen permeation experiments were performed on dense mixed-conducting ceramic-metal composite membranes (thickness 0.2 to 2 mm) Bi1.5Er0.5O3-Ag with 10.0, 27.8, and 40.0 volume percent (v/o) silver, respectively, in the temperature range 873 to 993 K and oxygen partial pressure range 10–3.5 to 1

Biogenic sulfur compounds and the global sulfur cycle

International Nuclear Information System (INIS)

Aneja, V.P.; Aneja, A.P.; Adams, D.F.

1982-01-01

Field measurements of biogenic sulfur compounds shows a great variation in concentrations and emission rates for H 2 S, DMS, CS 2 and COS. Measurements by the chamber method and estimates from micrometeorological sampling are employed to determine the earth-atmosphere flux of these gases. Much of the variation can be attributed to differences of climate and surface conditions, with marshes being a large source of biogenic sulfur (mean contribution 4 x 10 to the 6th ton/year maximum contribution 142 x 10 to the 6th ton/year). Considering that the estimated biogenic contribution needed to balance the global sulfur cycle ranges from 40- 230 x 10 to the 6th tons/year, the mean values are not sufficient to balance this cycle. Further experimental investigations are suggested in order to characterize the biogenic processes adequately

Crystal structure of superparamagnetic Mg0.2Ca0.8Fe2O4 nanoparticles synthesized by sol–gel method

International Nuclear Information System (INIS)

Escamilla-Pérez, A.M.; Cortés-Hernández, D.A.; Almanza-Robles, J.M.; Mantovani, D.; Chevallier, P.

2015-01-01

Powders of magnetic iron oxide nanoparticles (Mg 0.2 Ca 0.8 Fe 2 O 4 ) were prepared by a sol–gel method using ethylene glycol and nitrates of Fe, Ca and Mg as starting materials. Those powders were heat treated at different temperatures (573, 673, 773 and 873 K). In order to evaluate the effect of the heat treatment temperature on the nanoferrites properties, X-ray diffraction (XRD), vibrating sample magnetometry (VSM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) techniques were used. It was found that the reaction products exhibit nanometric sizes and superparamagnetic behavior. It is also demonstrated that, as the heat treatment temperature increases, the particle size and the saturation magnetization of the nanoferrites are increased. - Highlights: • Mg 0.2 Ca 0.8 Fe 2 O 4 superparamagnetic nanoparticles were successfully synthesized. • Particle average sizes of Ca–Mg ferrites were within the range of 8–25 nm. • The nanoferrite treated at 873 K showed a stoichiometry close to Mg 0.2 Ca 0.8 Fe 2 O 4 . • The heat treatment temperature has a strong effect on the crystal structure. • These nanoparticles are potential materials for magnetic hyperthermia

Vitis vinifera juice ameliorates depression-like behavior in mice by modulating biogenic amine neurotransmitters

Directory of Open Access Journals (Sweden)

Muhammad Aslam

2015-12-01

Full Text Available The advantageous effects of Vitis vinifera juice on depressive model mice were examined utilizing a blend of behavioral evaluations and biogenic amine neurotransmitter estimations. During the behavioral evaluations, immobility time on the forced swimming test and tail suspension test were measured in unstressed and immobilization-induced stressed mice. V. vinifera juice (4 mL/kg and 8 mL/kg and fluoxetine (20 mg/kg produced a significant decrease in immobility time of both unstressed and stressed mice when compared with their respective saline-treated control groups in both paradigms. Neurotransmitters were measured using high-performance liquid chromatography with electrochemical detector. V. vinifera juice raised the levels of both serotonin (p<0.001 and noradrenalin (p<0.001 in brain tissue. These outcomes give significant mechanistic insights into the protective effect of V. vinifera juice against depressive disorders. Our results showed that V. vinifera juice could relieve depressive manifestations in the rodent model of depression.

Effect of positively charged particles on sputtering damage of organic electro-luminescent diodes with Mg:Ag alloy electrodes fabricated by facing target sputtering

Directory of Open Access Journals (Sweden)

Kouji Suemori

2017-04-01

Full Text Available We investigated the influence of the positively charged particles generated during sputtering on the performances of organic light-emitting diodes (OLEDs with Mg:Ag alloy electrodes fabricated by sputtering. The number of positively charged particles increased by several orders of magnitude when the target current was increased from 0.1 A to 2.5 A. When a high target current was used, many positively charged particles with energies higher than the bond energy of single C–C bonds, which are typically found in organic molecules, were generated. In this situation, we observed serious OLED performance degradation. On the other hand, when a low target current was used, OLED performance degradation was not observed when the number of positively charged particles colliding with the organic underlayer increased. We concluded that sputtering damage caused by positively charged particles can be avoided by using a low target current.

Rapid Colorimetric Detection of Cartap Residues by AgNP Sensor with Magnetic Molecularly Imprinted Microspheres as Recognition Elements

Directory of Open Access Journals (Sweden)

Mao Wu

2018-06-01

Full Text Available The overuse of cartap in tea tree leads to hazardous residues threatening human health. A colorimetric determination was established to detect cartap residues in tea beverages by silver nanoparticles (AgNP sensor with magnetic molecularly imprinted polymeric microspheres (Fe3O4@mSiO2@MIPs as recognition elements. Using Fe3O4 as supporting core, mesoporous SiO2 as intermediate shell, methylacrylic acid as functional monomer, and cartap as template, Fe3O4@mSiO2@MIPs were prepared to selectively and magnetically separate cartap from tea solution before colorimetric determination by AgNP sensors. The core-shell Fe3O4@mSiO2@MIPs were also characterized by FT-IR, TEM, VSM, and experimental adsorption. The Fe3O4@mSiO2@MIPs could be rapidly separated by an external magnet in 10 s with good reusability (maintained 95.2% through 10 cycles. The adsorption process of cartap on Fe3O4@mSiO2@MIPs conformed to Langmuir adsorption isotherm with maximum adsorption capacity at 0.257 mmol/g and short equilibrium time of 30 min at 298 K. The AgNP colorimetric method semi-quantified cartap ≥5 mg/L by naked eye and quantified cartap 0.1–5 mg/L with LOD 0.01 mg/L by UV-vis spectroscopy. The AgNP colorimetric detection after pretreatment with Fe3O4@mSiO2@MIPs could be successfully utilized to recognize and detect cartap residues in tea beverages.

Synthesis of silver nanoparticles deposited on silica by γ-irradiation and preparation of PE/Ag nano compound masterbatches

International Nuclear Information System (INIS)

Nguyen, Thi Kim Lan; Dang, Van Phu; Nguyen, Ngoc Duy; Le, Anh Quoc; Nguyen, Quoc Hien; Nguyen, Thuy Ai Trinh

2013-01-01

Silver nanoparticles (AgNPs) deposited on silica were synthesized by gamma Co-60 irradiation of Ag + dispersion in silica/ethanol/water mixture (9/80/20:w/v/v). The reduction of Ag + is occurred by hydrated electron (e − aq ) and hydrogen atom (H • ) generated during radiolysis of ethanol/water. The conversion doses (Ag + → Ag 0 ) were determined by UV–Vis spectroscopy. The synthesized AgNPs/silica were characterized by transmission electron microscopy (TEM) and x-ray diffraction (XRD), which showed the size of AgNPs to be in the range of 5–40 nm for Ag + concentrations from 5 to 20 mM. Masterbatches of PE/AgNPs/silica compound with silver content from 250 to 1000 mg kg −1 were also prepared. These masterbatches can be suitably used for various applications such as antimicrobial food containers and packing films, etc. (paper)

Effect of cysteine and humic acids on bioavailability of Ag from Ag nanoparticles to a freshwater snail

Science.gov (United States)

Luoma, Samuel N.; Tasha Stoiber,; Croteau, Marie-Noele; Isabelle Romer,; Ruth Merrifeild,; Lead, Jamie

2016-01-01

Metal-based engineered nanoparticles (NPs) will undergo transformations that will affect their bioavailability, toxicity and ecological risk when released to the environment, including interactions with dissolved organic material. The purpose of this paper is to determine how interactions with two different types of organic material affect the bioavailability of silver nanoparticles (AgNPs). Silver uptake rates by the pond snail Lymnaea stagnalis were determined after exposure to 25 nmol l-1 of Ag as PVP AgNPs, PEG AgNPs or AgNO3, in the presence of either Suwannee River humic acid or cysteine, a high-affinity thiol-rich organic ligand. Total uptake rate of Ag from the two NPs was either increased or not strongly affected in the presence of 1 – 10 mg 1-1 humic acid. Humic substances contain relatively few strong ligands for Ag explaining their limited effects on Ag uptake rate. In contrast, Ag uptake rate was substantially reduced by cysteine. Three components of uptake from the AgNPs were quantified in the presence of cysteine using a biodynamic modeling approach: uptake of dissolved Ag released by the AgNPs, uptake of a polymer or large (>3kD) Ag-cysteine complex and uptake of the nanoparticle itself. Addition of 1:1 Ag:cysteine reduced concentrations of dissolved Ag, which contributed to, but did not fully explain the reductions in uptake. A bioavailable Ag-cysteine complex (> 3kD) appeared to be the dominant avenue of uptake from both PVP AgNPs and PEG AgNPs in the presence of cysteine. Quantifying the different avenues of uptake sets the stage for studies to assess toxicity unique to NPs.

Structure and superconductivity of double-doped Mg1-x(Al0.5Li0.5)xB2

DEFF Research Database (Denmark)

Xu, G.J.; Grivel, Jean-Claude; Abrahamsen, A.B.

2003-01-01

A series of polycrystalline samples of Mg1-x(Al0.5Li0.5)(x)B-2 (0less than or equal toxless than or equal to0.6) were prepared by a solid state reaction method and their structure, superconducting transition temperature and magneto-transport properties were investigated by means of X-ray diffract......A series of polycrystalline samples of Mg1-x(Al0.5Li0.5)(x)B-2 (0less than or equal toxless than or equal to0.6) were prepared by a solid state reaction method and their structure, superconducting transition temperature and magneto-transport properties were investigated by means of X......-ray diffraction (XRD), ac-susceptibility and resistance in varied magnetic fields. The double doping leads to decreases in both the lattice parameters a and c. The superconducting transition temperature (T-c) decreases with double doping, but the T-c is systematically higher than that of the single Al......-doped samples. It is suggested that the hole band filling has little effect on T-c at high doping level, while the disorder induced by doping plays an important role in suppressing T-c. A systematic comparison with Al-doped MgB2 of the structure, superconducting transition and irreversibility field is made. (C...

The n-Cu0.9Ag0.1In3Se5 chalcopyrite, electronic as well as ionic conductor

International Nuclear Information System (INIS)

Diaz, R

2008-01-01

A resistance increase with time of the n-Cu 0.9 Ag 0.1 In 3 Se 5 chalcopyrite has been observed. This new effect is analysed in terms of a hypothesis of ion migration and Schottky barrier formation. These results might explain why different solar cell efficiencies are obtained for the chalcopyrites, CuInSe 2 and CuIn x Ga 1-x Se 2 , when an In-rich film is deposited on top of the chalcopyrite. In these solar cells, ion migration can exist and a new effect appears similar to the one observed in our compound. The ions, probably the cations, are moved by the electrical field towards the cathode. A gradient of mobile ions appears across the sample and the positive charge is accumulated near this electrode such that it varies the metal-semiconductor interface. This interface is a Schottky barrier where the contact potential is a function of time due to the arrival of ions. The electrical measurements have been carried out on a solid state device, graphite/n-Cu 0.9 Ag 0.1 In 3 Se 5 /graphite. The current intensity and the potential drop across the sample have been measured with time when a constant electrical potential is applied for 600 s at dark or under ultraviolet illumination and at room temperature. A comparative study in similar electrical conditions is done; the current intensity difference and the potential drop across the difference (under ultraviolet illumination minus at dark) are not constant and both measurements increase with time

Methyl chavicol: characterization of its biogenic emission rate

NARCIS (Netherlands)

Bouvier-Brown, N.C.; Goldstein, A.H.; Worton, D.R.; Matross, D.M.; Gilman, J.B.; Kuster, W.C.; Welsh-Bon, D.; Warneke, C.; de Gouw, J.A.; Cahill, M.J.; Holzinger, R.

2009-01-01

We report measurements of ambient atmospheric mixing ratios for methyl chavicol and determine its biogenic emission rate. Methyl chavicol, a biogenic oxygenated aromatic compound, is abundant within and above Blodgett Forest, a ponderosa pine forest in the Sierra Nevada Mountains of California.