Production of methyl-vinyl ketone from levulinic acid

Energy Technology Data Exchange (ETDEWEB)

Dumesic, James A [Verona, WI; West,; Ryan, M [Madison, WI

2011-06-14

A method for converting levulinic acid to methyl vinyl ketone is described. The method includes the steps of reacting an aqueous solution of levulinic acid, over an acid catalyst, at a temperature of from room temperature to about 1100 K. Methyl vinyl ketone is thereby formed.

Atmospheric mixing ratios of methyl ethyl ketone (2-butanone in tropical, boreal, temperate and marine environments

Directory of Open Access Journals (Sweden)

A. M. Yáñez-Serrano

2016-09-01

Full Text Available Methyl ethyl ketone (MEK enters the atmosphere following direct emission from vegetation and anthropogenic activities, as well as being produced by the gas-phase oxidation of volatile organic compounds (VOCs such as n-butane. This study presents the first overview of ambient MEK measurements at six different locations, characteristic of forested, urban and marine environments. In order to understand better the occurrence and behaviour of MEK in the atmosphere, we analyse diel cycles of MEK mixing ratios, vertical profiles, ecosystem flux data, and HYSPLIT back trajectories, and compare with co-measured VOCs. MEK measurements were primarily conducted with proton-transfer-reaction mass spectrometer (PTR-MS instruments. Results from the sites under biogenic influence demonstrate that vegetation is an important source of MEK. The diel cycle of MEK follows that of ambient temperature and the forest structure plays an important role in air mixing. At such sites, a high correlation of MEK with acetone was observed (e.g. r2 = 0.96 for the SMEAR Estonia site in a remote hemiboreal forest in Tartumaa, Estonia, and r2 = 0.89 at the ATTO pristine tropical rainforest site in central Amazonia. Under polluted conditions, we observed strongly enhanced MEK mixing ratios. Overall, the MEK mixing ratios and flux data presented here indicate that both biogenic and anthropogenic sources contribute to its occurrence in the global atmosphere.

The influence of solvent stress on MMS-induced genetic change in Saccharomyces cerevisiae.

Science.gov (United States)

Zimmermann, F K; Rohlfs, A

1991-01-01

MMS induced mitotic recombination but not mitotic chromosome loss when tested in pure form in strain D61.M of Saccharomyces cerevisiae, confirming previous results of Albertini (1991), whereas in Aspergillus nidulans it also induced chromosomal malsegregation in addition to mitotic recombination (Käfer, 1988). However, induction of mitotic chromosome loss was observed in combination with strong inducers of chromosome loss such as the aprotic polar solvents ethyl acetate and to a lesser extent methyl ethyl ketone but not with gamma-valerolactone and propionitrile. In addition to this, 4 solvents, dimethyl formamide, dimethyl sulfoxide, dioxane and pyridine, enhanced the MMS-induced mitotic recombination in strain D61.M. An enhancement of MMS-induced mitotic recombination and reverse mutation could be demonstrated for ethyl acetate and gamma-valerolactone in yeast strain D7.

Biofiltration of paint solvent mixtures in two reactor types: overloading by polar components.

Science.gov (United States)

Paca, Jan; Halecky, Martin; Misiaczek, Ondrej; Kozliak, Evguenii I; Jones, Kim

2012-01-01

Steady-state performances of a trickle bed reactor (TBR) and a biofilter (BF) in loading experiments with increasing inlet concentrations of polar solvents, acetone, methyl ethyl ketone, methyl isobutyl ketone and n-butyl acetate, were investigated, along with the system's dynamic responses. Throughout the entire experimentation time, a constant loading rate of aromatic components of 4 g(c)·m(-3)·h(-1) was maintained to observe the interactions between the polar substrates and aromatic hydrocarbons. Under low combined substrate loadings, the BF outperformed TBR not only in the removal of aromatic hydrocarbons but also in the removal of polar substrates. However, increasing the loading rate of polar components above the threshold value of 31-36 g(c)·m(-3)·h(-1) resulted in a steep and significant drop in the removal efficiencies of both polar (except for butyl acetate) and hydrophobic components, which was more pronounced in the BF; so the relative TBR/BF efficiency became reversed under such overloading conditions. A step-drop of the overall OL(POLAR) (combined loading by polar air pollutants) from overloading values to 7 g(c)·m(-3)·h(-1) resulted in an increase of all pollutant removal efficiencies, although in TBR the recovery was preceded by lag periods lasting between 5 min (methyl ethyl ketone) to 3.7 h (acetone). The occurrence of lag periods in the TBR recovery was, in part, due to the saturation of mineral medium with water-soluble polar solvents, particularly, acetone. The observed bioreactor behavior was consistent with the biological steps being rate-limiting.

21 CFR 172.872 - Methyl ethyl cellulose.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methyl ethyl cellulose. 172.872 Section 172.872... CONSUMPTION Multipurpose Additives § 172.872 Methyl ethyl cellulose. The food additive methyl ethyl cellulose... a cellulose ether having the general formula [C6H(10 -x-y)O5(CH3)x(C2H5)y]n, where x is the number...

Bacterial production of methyl ketones

Energy Technology Data Exchange (ETDEWEB)

Beller, Harry R.; Goh, Ee-Been

2017-01-31

The present invention relates to methods and compositions for increasing production of methyl ketones in a genetically modified host cell that overproduces .beta.-ketoacyl-CoAs through a re-engineered .beta.-oxidation pathway and overexpresses FadM.

Determining an Efficient Solvent Extraction Parameters for Re-Refining of Waste Lubricating Oils

Directory of Open Access Journals (Sweden)

Hassan Ali Durrani

2012-04-01

Full Text Available Re-refining of vehicle waste lubricating oil by solvent extraction is one of the efficient and cheapest methods. Three extracting solvents MEK (Methyl-Ethyl-Ketone, 1-butanol, 2-propanol were determined experimentally for their performance based on the parameters i.e. solvent type, solvent oil ratio and extraction temperature. From the experimental results it was observed the MEK performance was highest based on the lowest oil percent losses and highest sludge removal. Further, when temperature of extraction increased the oil losses percent also decreased. This is due to the solvent ability that dissolves the base oil in waste lubricating oil and determines the best SOR (Solvent Oil Ratio and extraction temperatures.

Synthesis and investigation of solvent effects on the ultraviolet absorption spectra of 5-substituted-4-methyl-3-cyano-6-hydroxy-2-pyridones

Directory of Open Access Journals (Sweden)

NATASA V. VALENTIC

2001-08-01

Full Text Available A number of 5-substituted-4-methyl-3-cyano-6-hydroxy-2-pyridones from cyanoacetamide and the corresponding alkyl ethyl acetoacetates were synthesized according to modified literature procedures. The alkyl ethyl acetoacetates were obtained by the reaction of C-alkylation of ethyl acetoacetate. An investigation of the reaction conditions for the synthesis of 4-methyl-3-cyano-6-hydroxy-2-pyridone from cyanoacetamide and ethyl acetoacetate in eight different solvents was also performed. The ultraviolet absorption spectra of synthesized pyridones were measured in nine different solvents in the range 200–400 nm. The effects of solvent polarity and hydrogen bonding on the absorption spectra are interpreted by means of linear solvation energy relationships using a general equation of the form n = n0 + sp* + aa + bb, where p* is a measure of the solvent polarity, a is the scale of the solvent hydrogen bond donor acidities and b is the scale of the solvent hydrogen bond acceptor basicities.

Incineration of oxygenated volatile organic compounds. Experimental study and kinetic modeling of the oxidation of methyl ethyl ketone, ethyl acetate and butan-2-ol in methane flames; Incineration de composes organiques volatils oxygenes. Etude experimentale et modelisation cinetique de l'oxydation de la methyl ethyl cetone, de l'acetate d'ethyle et du butan-2-ol dans des flammes de methane

Energy Technology Data Exchange (ETDEWEB)

Decottignies, V

2000-12-01

This work deals with the low pressure (0.05 atm) degradation of three volatile organic compounds (VOCs): methyl-ethyl-ketone, ethyl acetate and butan-2-ol, in premixed stoichiometric laminar methane flames seeded with 1 to 3% of each VOC. Molar fraction profiles of species have been obtained using microprobe sampling coupled with a gas chromatography and a mass spectroscopy analysis. Temperature profiles have been obtained using the covered thermocouple technique in the presence of the microprobe. The addition of a VOC in the initial reagents mixture leads to an increase of the quantity of intermediate hydrocarbon compounds and in particular of some soot precursor species. The degradation of VOCs leads to the formation of oxygenated intermediates like methanol, dimethyl-ether, acetaldehyde, propanal, acetone and vinyl acetate, the type of VOC having an effect on the quantities produced. The degradation of a VOC can lead to the formation of more toxic or polluting compounds (methyl vinyl ketone, acetic acid and acrolein) than the VOC itself. In the conditions of the study, the intermediate compounds are totally destructed inside the reactional area of the flame front and are no more present in the burnt gases. Sub-mechanisms of VOC oxidation have been developed using experimental observations and the most recent recommendations of the literature. These sub-mechanisms comprise 49 species involved in 241 elementary reactions. Their validation has been performed by comparing the experiment with the kinetic modeling on the molar fraction profiles of the detected species. Experimental data are well reproduced by the model for most species. The addition of a VOC inside the initial reagents mixture creates an important reactivity increase, in particular in the case of butan-2-ol seeded flames. The analysis of reactional ways has permitted to draw out the main reactions responsible for the degradation of the 3 VOCs and the ways of formation and consumption of the

Synthesis of tritium labelled methyl vinyl ketone and its use in copolymer analysis

International Nuclear Information System (INIS)

Burfield, D.R.; Savariar, C.M.

1980-01-01

The synthesis of tritiated methyl vinyl ketone by base catalysed exchange and its use in determining the ketone content of styrene/methyl vinyl ketone copolymers are reported. Methods of assay are described in detail and the general applicability of the method is discussed. (author)

Incineration of oxygenated volatile organic compounds. Experimental study and kinetic modeling of the oxidation of methyl ethyl ketone, ethyl acetate and butan-2-ol in methane flames; Incineration de composes organiques volatils oxygenes. Etude experimentale et modelisation cinetique de l'oxydation de la methyl ethyl cetone, de l'acetate d'ethyle et du butan-2-ol dans des flammes de methane

Energy Technology Data Exchange (ETDEWEB)

Decottignies, V.

2000-12-01

This work deals with the low pressure (0.05 atm) degradation of three volatile organic compounds (VOCs): methyl-ethyl-ketone, ethyl acetate and butan-2-ol, in premixed stoichiometric laminar methane flames seeded with 1 to 3% of each VOC. Molar fraction profiles of species have been obtained using microprobe sampling coupled with a gas chromatography and a mass spectroscopy analysis. Temperature profiles have been obtained using the covered thermocouple technique in the presence of the microprobe. The addition of a VOC in the initial reagents mixture leads to an increase of the quantity of intermediate hydrocarbon compounds and in particular of some soot precursor species. The degradation of VOCs leads to the formation of oxygenated intermediates like methanol, dimethyl-ether, acetaldehyde, propanal, acetone and vinyl acetate, the type of VOC having an effect on the quantities produced. The degradation of a VOC can lead to the formation of more toxic or polluting compounds (methyl vinyl ketone, acetic acid and acrolein) than the VOC itself. In the conditions of the study, the intermediate compounds are totally destructed inside the reactional area of the flame front and are no more present in the burnt gases. Sub-mechanisms of VOC oxidation have been developed using experimental observations and the most recent recommendations of the literature. These sub-mechanisms comprise 49 species involved in 241 elementary reactions. Their validation has been performed by comparing the experiment with the kinetic modeling on the molar fraction profiles of the detected species. Experimental data are well reproduced by the model for most species. The addition of a VOC inside the initial reagents mixture creates an important reactivity increase, in particular in the case of butan-2-ol seeded flames. The analysis of reactional ways has permitted to draw out the main reactions responsible for the degradation of the 3 VOCs and the ways of formation and consumption of the

Solubility of daidzin in different organic solvents and (ethyl alcohol + water) mixed solvents

International Nuclear Information System (INIS)

Fan, Jie-Ping; Yang, Dan; Xu, Xiao-Kang; Guo, Xiao-Jie; Zhang, Xue-Hong

2015-01-01

Highlights: • The solubilities of daidzin were measured in various solvents. • The solubility data were correlated by three models. • The thermodynamic properties of the dissolution process were also determined. - Abstract: The solubility of daidzin in different organic solvents and (ethyl alcohol + water) mixed solvents was measured by high performance liquid chromatography (HPLC) analysis method from T = (283.2 to 323.2) K at atmosphere pressure. The results show that at higher temperature more daidzin dissolves, and moreover, the solubility increases with the ethyl alcohol mole fraction increase in the (ethyl alcohol + water) mixed solvents. The experimental solubility values were correlated by a simplified thermodynamic equation, λh equation and modified Apelblat equation. Based on the solubility of daidzin, the enthalpy and entropy of solution were also evaluated by van’t Hoff equation. The results illustrated that the dissolution process of daidzin is endothermic and entropy driven

Atmospheric fate of methyl vinyl ketone

DEFF Research Database (Denmark)

Praske, Eric; Crounse, John D; Bates, Kelvin H

2015-01-01

First generation product yields from the OH-initiated oxidation of methyl vinyl ketone (3-buten-2-one, MVK) under both low and high NO conditions are reported. In the low NO chemistry, three distinct reaction channels are identified leading to the formation of (1) OH, glycolaldehyde, and acetyl...

Effect of solvent composition on dispersing ability of reaction sialon suspensions.

Science.gov (United States)

Xu, Xin; Oliveira, Marta; Ferreira, José M F

2003-03-15

This work focuses on the optimization of the rheological behavior of suspensions considering different solvent compositions. The effects of methyl ethyl ketone (MEK)/ethanol (E) solvent mixtures on reaction sialon suspensions were investigated by measuring sedimentation behavior, adsorption of dispersant, and flow behavior. It was shown that both the flow behavior and the sedimentation behavior strongly depended on selection of solvent composition. Using 3 wt% KD1 as dispersant, well-dispersed colloidal suspensions could be obtained in MEK-rich solvents. The suspensions with 60 vol% MEK/40 vol% E as solvent could be fitted to the Bingham model with very low yield stress, while suspensions with pure MEK or ethanol-rich mixtures as solvent showed pseudo plastic behavior with relatively high yield stress values. A model was proposed to explain the different flow behaviors of suspensions considering the different configurations of dispersant at particles' surfaces.

Installation Restoration Program. Phase I. Records Search Columbus Air force Base, Mississippi.

Science.gov (United States)

1985-04-01

with the river flood plains and pine plantations on drier upland areas. Loblolly pine ( Pinus taeda) is the dominant planted pine and is used for pulp...Maintenance MCL maximum contaminant level Methyl ethyl ketone A solvent used in paint thinner, stripper, and a (MEK) wide variety of industrial...l milligrams per liter A-3 Methyl isobutyl A solvent used in paint stripper, thinner, and a - ketone (MIBK) wide variety of industrial applications

Method of preparing 17β-hydroxy-4-androstene-3-one, 17α-methyl-17β-hydroxy-4-androstene-3-one and 17β-hydroxy-4-estrene-3-one labelled with iodine radioisotopes

International Nuclear Information System (INIS)

Kozak, I.; Dvorak, P.; Hampl, R.

1983-01-01

The patent claims the preparation of radioactive iodine derivatives of testosterone, methyl testosterone, and nortestosterone with the iodine atom bound directly to the steroid skeleton. An aqueous solution of carrier-free radioactive sodium iodide is evaporated until dry. The evaporation residue is extracted with a polar organic solvent and the resulting extract is added to the steroid designed for labelling. The solution is evaporated until dry and the evaporation residue is heated at a temperature within the range of the melting temperature of the respective steroid to 190 degC. To separate the immunoreactive radioactive product from admixtures, repeated thin-layer (silica gel) chromatography is used in cyclohexane-ethyl acetate (ratio 1:1) and benzene-methanol (ratio 9:1) systems. Methyl ethyl ketone, methanol, acetone and diethyl ether are used as polar solvents. (J.P.)

Solubility and solution thermodynamics of 2-methyl-6-nitroaniline in ten organic solvents at elevated temperatures

International Nuclear Information System (INIS)

Cong, Yang; Wang, Jian; Du, Cunbin; Han, Shuo; Zhao, Hongkun

2016-01-01

Highlights: • Solubility of 2-methyl-6-nitroaniline in ten solvents were determined. • The solubility were correlated with four thermodynamic models. • Standard dissolution enthalpy and excess enthalpy of the solutions were computed. - Abstract: Knowledge of solubility for 2-methyl-6-nitroaniline in different solvents is essential for its purification and further theoretical studies. In this paper, the solid-liquid equilibrium for 2-methyl-6-nitroaniline in ten pure organic solvents (methanol, ethanol, n-propanol, isopropanol, toluene, ethyl acetate, acetonitrile, acetone, cyclohexane and 1,4-dioxane) was established using the isothermal saturation method at temperatures T = (278.15–313.15) K under pressure of 101.2 kPa, and the solubility of 2-methyl-6-nitroaniline in these solvents were determined by a high-performance liquid chromatography (HPLC). In general, the mole fraction solubility followed the following order from high to low in different solvents: 1,4-dioxane (0.1799–0.3390) > acetone (0.1128–0.3010) > ethyl acetate (0.08414–0.2654) > acetonitrile (0.04179–0.2027) > toluene (0.02367–0.1104) > n-propanol (0.01080–0.04514) > ethanol (0.01020–0.04202) > isopropanol (0.008595–0.03763) > methanol (0.007391–0.03198) > cyclohexane (0.001027–0.005617). The modified Apelblat equation, λh equation, Wilson model and NRTL model were employed to correlate the measured solubility data of 2-methyl-6-nitroaniline in the selected solvents. Results indicated that the largest values of RAD and RMSD acquired by the four models were less than 0.76% and 9.13 × 10"−"4, respectively. The modified Apelblat equation provided better results than the other three models. Furthermore, the standard dissolution enthalpy and excess enthalpy of the solutions were computed from the solubility values. The standard dissolution enthalpies vary within the range from (14.88 to 45.57) kJ·mol"−"1 and are all positive, the dissolution process of 2-methyl-6

Solvent effect on the rate and equilibrium of reaction between 10-phenylphenoxarsine and methyl iodide. Vliyanie rastvoritelya na skorost' i ravnovesie reaktsii 10-fenilfenoksarsina s iodistym metilom

Energy Technology Data Exchange (ETDEWEB)

Gavrilov, V I; Gumerov, N S; Rakhmatullin, R R [Kazanskij Khimiko-Tekhnologicheskij Inst., Kazan (USSR)

1990-02-01

Effect of solvent nature on nucleophilic capacity of three-coordinated arsenic and the equilibrium state of 10-phenylphenoxarsine (PA) reaction with methyl iodide are studied. Kinetic investigations are carried out by the conductometry at 24,35,45 deg C. It is established that quaternization of PA with methyl iodide when substituting a solvent (ketone for alcohol) increases 3-14 times with simultaneous growth of the activation energy value. When transforming from aprotic solvents to protic ones PA interaction equilibrium with methyl iodide shifts to the side of arsonic salt formation.

Solubility measurement and correlation of the form A of ibrutinib in organic solvents from 278.15 to 323.15 K

International Nuclear Information System (INIS)

Chen, Zhenzhen; Zhai, Jinghuan; Liu, Xijian; Mao, Shimin; Zhang, Lijuan; Rohani, Sohrab; Lu, Jie

2016-01-01

Highlights: • The solubility of ibrutinib (form A) in organic solvents was firstly reported. • Apelblat, λh, empirical polynomial equations were used to correlate the solubility. • The solubility order: MEK > acetone > EA > 1-butanol > acetonitrile ≈ IPA > MTBE. - Abstract: In this work, the solubility of the form A of ibrutinib in isopropanol (IPA), 1-butanol, ethyl acetate (EA), acetonitrile, acetone, methyl ethyl ketone (MEK) and methyl tertiary butyl ether (MTBE) was firstly experimentally determined by a gravimetric method in the temperature range from 278.15 to 323.15 K at atmospheric pressure. The experimental solubility data were correlated by several commonly used models including the modified Apelblat equation, the Buchowski-Ksiazczak λh equation and an empirical quartic polynomial equation. The results showed that, in the temperature range investigated, the solubility of ibrutinib generally increased with the increasing temperature, and the solubility order at the room temperature in the studied solvents was: MEK > acetone > ethyl acetate > 1-butanol > acetonitrile ≈ isopropanol > MTBE. In addition, all the models gave satisfactory correlation results, in which the empirical quartic polynomial equation stood out to be more suitable with a higher accuracy than the other two equations.

Li-Ion Cells Employing Electrolytes With Methyl Propionate and Ethyl Butyrate Co-Solvents

Science.gov (United States)

Smart, Marshall C.; Bugga, Ratnakumar V.

2011-01-01

Future NASA missions aimed at exploring Mars and the outer planets require rechargeable batteries that can operate at low temperatures to satisfy the requirements of such applications as landers, rovers, and penetrators. A number of terrestrial applications, such as hybrid electric vehicles (HEVs) and electric vehicles (EVs) also require energy storage devices that can operate over a wide temperature range (i.e., -40 to +70 C), while still providing high power capability and long life. Currently, the state-of-the-art lithium-ion system has been demonstrated to operate over a wide range of temperatures (-30 to +40 C); however, the rate capability at the lower temperatures is very poor. These limitations at very low temperatures are due to poor electrolyte conductivity, poor lithium intercalation kinetics over the electrode surface layers, and poor ionic diffusion in the electrode bulk. Two wide-operating-temperature-range electrolytes have been developed based on advances involving lithium hexafluorophosphate-based solutions in carbonate and carbonate + ester solvent blends, which have been further optimized in the context of the technology and targeted applications. The approaches employed include further optimization of electrolytes containing methyl propionate (MP) and ethyl butyrate (EB), which are effective co-solvents, to widen the operating temperature range beyond the baseline systems. Attention was focused on further optimizing ester-based electrolyte formulations that have exhibited the best performance at temperatures ranging from -60 to +60 C, with an emphasis upon improving the rate capability at -20 to -40 C. This was accomplished by increasing electrolyte salt concentration to 1.20M and increasing the ester content to 60 percent by volume to increase the ionic conductivity at low temperatures. Two JPL-developed electrolytes 1.20M LiPF6 in EC+EMC+MP (20:20:60 v/v %) and 1.20M LiPF6 in EC+EMC+EB (20:20:60 v/v %) operate effectively over a wide

Determinação de metil-etil-cetona em amostras de urina com amostragem por micro extração em fase sólida (MEFS em headspace associada à cromatografia gasosa com detector de ionização de chama (CG-DIC Determination of methyl ethyl ketone in urine samples by headspace solid phase micro extraction (SPME sampling associated to gas chromatography with flame-ionization detectoR (GC-FID

Directory of Open Access Journals (Sweden)

Marina Venzon Antunes

2008-01-01

Full Text Available Methyl ethyl ketone (MEK is a solvent commonly used in chemical, paint and shoe industry. The aim of this study was to develop and validate a method for urinary quantification of MEK, employing headspace solid phase micro extraction sampling (SPME coupled to gas chromatography with flame ionization detection (GC-FID. The calibration curve (y=4.6851x-0.0011 presented good linearity with r²=0.9993. Accuracy (94-109%, intra-assay precision (4.07-5.91% and inter-assay precision (3.03-5.62% were acceptable. The quantification limit was 0.19 mg/L. This low cost method can be used routinely in the biological monitoring of occupational exposure to MEK, according to the requirements of the Brazilian legislation.

Ru (III) Catalyzed Oxidation of Aliphatic Ketones by N-Bromosuccinimide in Aqueous Acetic Acid: A Kinetic Study

Science.gov (United States)

Giridhar Reddy, P.; Ramesh, K.; Shylaja, S.; Rajanna, K. C.; Kandlikar, S.

2012-01-01

Kinetics of Ru (III) catalyzed oxidation of aliphatic ketones such as acetone, ethyl methyl ketone, diethyl ketone, iso-butylmethyl ketone by N-bromosuccinimide in the presence of Hg(II) acetate have been studied in aqueous acid medium. The order of [N-bromosuccinimide] was found to be zero both in catalyzed as well as uncatalyzed reactions. However, the order of [ketone] changed from unity to a fractional one in the presence of Ru (III). On the basis of kinetic features, the probable mechanisms are discussed and individual rate parameters evaluated. PMID:22654610

Efficiency of solvent extraction methods for the determination of methyl mercury in forest soils

Energy Technology Data Exchange (ETDEWEB)

Qian, J. [Department of Forest Ecology, Swedish University of Agricultural Sciences, Umeaa (Sweden); Dept. of Analytical Chemistry, Umeaa Univ. (Sweden); Skyllberg, U. [Department of Forest Ecology, Swedish University of Agricultural Sciences, Umeaa (Sweden); Tu, Q.; Frech, W. [Dept. of Analytical Chemistry, Umeaa Univ. (Sweden); Bleam, W.F. [Dept. of Soil Science, University of Wisconsin, Madison, WI (United States)

2000-07-01

Methyl mercury was determined by gas chromatography, microwave induced plasma, atomic emission spectrometry (GC-MIP-AES) using two different methods. One was based on extraction of mercury species into toluene, pre-concentration by evaporation and butylation of methyl mercury with a Grignard reagent followed by determination. With the other, methyl mercury was extracted into dichloromethane and back extracted into water followed by in situ ethylation, collection of ethylated mercury species on Tenax and determination. The accuracy of the entire procedure based on butylation was validated for the individual steps involved in the method. Methyl mercury added to various types of soil samples showed an overall average recovery of 87.5%. Reduced recovery was only caused by losses of methyl mercury during extraction into toluene and during pre-concentration by evaporation. The extraction of methyl mercury added to the soil was therefore quantitative. Since it is not possible to directly determine the extraction efficiency of incipient methyl mercury, the extraction efficiency of total mercury with an acidified solution containing CuSO{sub 4} and KBr was compared with high-pressure microwave acid digestion. The solvent extraction efficiency was 93%. For the IAEA 356 sediment certified reference material, mercury was less efficiently extracted and determined methyl mercury concentrations were below the certified value. Incomplete extraction could be explained by the presence of a large part of inorganic sulfides, as determined by x-ray absorption near-edge structure spectroscopy (XANES). Analyses of sediment reference material CRM 580 gave results in agreement with the certified value. The butylation method gave a detection limit for methyl mercury of 0.1 ng g{sup -1}, calculated as three times the standard deviation for repeated analysis of soil samples. Lower values were obtained with the ethylation method. The precision, expressed as RSD for concentrations 20 times

Solid–liquid phase equilibrium and dissolution properties of ethyl vanillin in pure solvents

International Nuclear Information System (INIS)

Wu, Hao; Wang, Jingkang; Zhou, Yanan; Guo, Nannan; Liu, Qi; Zong, Shuyi; Bao, Ying; Hao, Hongxun

2017-01-01

Highlights: • Solubility of ethyl vanillin in eight pure solvents were determined by a static analytical method. • The experimental solubility data of ethyl vanillin were correlated and analyzed by four thermodynamic models. • Dissolution thermodynamic properties of ethyl vanillin were calculated and discussed. - Abstract: The solubility of ethyl vanillin (EVA) in eight pure solvents were determined in different temperature ranges from (273.15 to 318.15) K by a static analytical method. In the temperature ranges investigated, it was found that the solubility of EVA in all the selected solvents increased with the rising of temperature. Furthermore, four thermodynamic models were used to correlate the experimental solubility data and the calculation results showed that selected models can be used to correlate the solubility data with satisfactory accuracy. Finally, the dissolution thermodynamic properties, including dissolution Gibbs energy, dissolution enthalpy and dissolution entropy of EVA in the eight selected solvents were calculated.

Recovery of hafnium values from loaded extraction solvent

International Nuclear Information System (INIS)

Abodishish, H.A.

1989-01-01

This patent describes an improvement in a process for recovering high purity hafnium hydroxide from a methyl isobutyl ketone organic solvent that is substantially free of sulfate ions and contains hafnium thiocyanate and thiocyanic acid. The improvement comprising reacting the organic solvent with ammonia to produce a reaction product in the form of a methyl isobutyl ketone organic solvent that is substantially free of sulfate ions and contains ammonium thiocyanite solution and hafnium hydroxide; separating the constituents of the reaction product in accordance with their respective specific gravities to produce a hafnium hydroxide sludge as one of the separation products; and removing the liquid component of the sludge to yield a high purity hafnium hydroxide ready for calcination to hafnium oxide

Effect of degree of sulfonation and casting solvent on sulfonated poly(ether ether ketone) membrane for vanadium redox flow battery

Science.gov (United States)

Xi, Jingyu; Li, Zhaohua; Yu, Lihong; Yin, Bibo; Wang, Lei; Liu, Le; Qiu, Xinping; Chen, Liquan

2015-07-01

The properties of sulfonated poly(ether ether ketone) (SPEEK) membranes with various degree of sulfonation (DS) and casting solvent are investigated for vanadium redox flow battery (VRFB). The optimum DS of SPEEK membrane is firstly confirmed by various characterizations such as physicochemical properties, ion selectivity, and VRFB single-cell performance. Subsequently the optimum casting solvent is selected for the optimum DS SPEEK membrane within N,N‧-dimethylformamide (DMF), N,N‧-dimethylacetamide (DMAc), N-methyl-2-pyrrolidone (NMP), and dimethylsulfoxide (DMSO). The different performance of SPEEK membranes prepared with various casting solvents can be attributed to the different interaction between solvent and -SO3H group of SPEEK. In the VRFB single-cell test, the optimum SPEEK membrane with DS of 67% and casting solvent of DMF (S67-DMF membrane) exhibits higher VRFB efficiencies and better cycle-life performance at 80 mA cm-2. The investigation of various DS and casting solvent will be effective guidance on the selection and modification of SPEEK membrane towards VRFB application.

Theoretical study of chain transfer to solvent reactions of alkyl acrylates.

Science.gov (United States)

Moghadam, Nazanin; Srinivasan, Sriraj; Grady, Michael C; Rappe, Andrew M; Soroush, Masoud

2014-07-24

This computational and theoretical study deals with chain transfer to solvent (CTS) reactions of methyl acrylate (MA), ethyl acrylate (EA), and n-butyl acrylate (n-BA) self-initiated homopolymerization in solvents such as butanol (polar, protic), methyl ethyl ketone (MEK) (polar, aprotic), and p-xylene (nonpolar). The results indicate that abstraction of a hydrogen atom from the methylene group next to the oxygen atom in n-butanol, from the methylene group in MEK, and from a methyl group in p-xylene by a live polymer chain are the most likely mechanisms of CTS reactions in MA, EA, and n-BA. Energy barriers and molecular geometries of reactants, products, and transition states are predicted. The sensitivity of the predictions to three hybrid functionals (B3LYP, X3LYP, and M06-2X) and three different basis sets (6-31G(d,p), 6-311G(d), and 6-311G(d,p)) is investigated. Among n-butanol, sec-butanol, and tert-butanol, tert-butanol has the highest CTS energy barrier and the lowest rate constant. Although the application of the conductor-like screening model (COSMO) does not affect the predicted CTS kinetic parameter values, the application of the polarizable continuum model (PCM) results in higher CTS energy barriers. This increase in the predicted CTS energy barriers is larger for butanol and MEK than for p-xylene. The higher rate constants of chain transfer to n-butanol reactions compared to those of chain transfer to MEK and p-xylene reactions suggest the higher CTS reactivity of n-butanol.

The incorporation of [1-14C] acetate into the methyl ketones that occur in steam-distillates of bovine milk fat.

Science.gov (United States)

Lawrence, R C; Hawke, J C

1966-01-01

1. The (14)C-labelling of the fatty acids and the methyl ketones in steam-distillates of milk fat from a lactating cow that had been injected intravenously with [1-(14)C]acetate was determined. 2. The labelling patterns of the C(6)-C(16) fatty acids and the corresponding methyl ketones with one fewer carbon atoms were similar, particularly so for the C(5)-C(10) compounds at 9 and 22hr. after the injection of [1-(14)C]acetate. The isolation of (14)C-labelled methyl ketones in the range C(3)-C(15) is evidence that the beta-oxo acid precursors, which are glyceride-bound in the milk fat, are synthesized in the mammary gland from acetate. The absence of heptadecan-2-one in steam-distillates and the extremely low specific radioactivity of stearic acid are further evidence for this biosynthetic pathway. 3. The specific radioactivities of the C(5)-C(15) methyl ketones were higher (with the exception of C(9) methyl ketone in the second milking) than the specific activities of the corresponding fatty acids with one more carbon atom. This is consistent with the methyl ketone precursors' being formed during the biosynthesis of fatty acids rather than being products of beta-oxidation of fatty acids.

Excess enthalpies and (vapour + liquid) equilibrium data for the binary mixtures of dimethylsulphoxide with ketones

International Nuclear Information System (INIS)

Radhamma, M.; Venkatesu, P.; Rao, M.V. Prabhakara; Prasad, D.H.L.

2007-01-01

Excess enthalpies (H E ), at ambient pressure and T = 298.15 K, have been measured by using a solution calorimeter for the binary liquid mixtures of dimethyl sulphoxide (DMSO) with ketones, as a function of composition. The ketones chosen in the present investigation were methyl ethyl ketone (MEK), methyl isobutyl ketone (MIBK), and cyclohexanone (CH). The H E values are positive over the entire composition range for the three binary mixtures. Furthermore, the (vapour + liquid) equilibrium (VLE) was measured at 715 Torr for these mixtures, of different compositions, with the help of Swietoslawski-ebulliometer. The experimental temperature-mole fraction (t-x) data were used to compute Wilson parameters and then used to calculate the equilibrium vapour-phase compositions as well as the theoretical points for these binary mixtures. These Wilson parameters are used to calculate activity coefficients (γ) and these in turn to calculate excess Gibbs free energy (G E ). The intermolecular interactions and structural effects were analyzed on the basis of the measured and derived properties

Fragrance material review on methyl-2,6,10-trimethylcyclododeca-2,5,9-trien-1-yl ketone.

Science.gov (United States)

Scognamiglio, J; Letizia, C S; Api, A M

2013-12-01

A toxicologic and dermatologic review of methyl 2,6,10-trimethylcyclododeca-2,5,9-trien-1-yl ketone when used as a fragrance ingredient is presented. Methyl 2,6,10-trimethylcyclododeca-2,5,9-trien-1-yl ketone is a member of the fragrance structural group Alkyl Cyclic Ketones. These fragrances can be described as being composed of an alkyl, R1, and various substituted and bicyclic saturated or unsaturated cyclic hydrocarbons, R2, in which one of the rings may include up to 12 carbons. Alternatively, R2 may be a carbon bridge of C2-C4 carbon chain length between the ketone and cyclic hydrocarbon. This review contains a detailed summary of all available toxicology and dermatology papers that are related to this individual fragrance ingredient and is not intended as a stand-alone document. Available data for methyl 2,6,10-trimethylcyclododeca-2,5,9-trien-1-yl ketone were evaluated then summarized and includes physical properties, acute toxicity, skin irritation, mucous membrane (eye) irritation, skin sensitization, repeated dose, and genotoxicity data. A safety assessment of the entire Alkyl Cyclic Ketones will be published simultaneously with this document; please refer to Belsito et al. (Belsito, D., Bickers, D., Bruze, M., Calow, P., Dagli, M., Fryer, A.D., Greim, H., Miyachi, Y., Saurat, J.H., Sipes, I.G., 2013. A Toxicologic and Dermatologic Assessment of Alkyl Cyclic Ketones When Used as Fragrance Ingredients (submitted for publication)) for an overall assessment of the safe use of this material and all Alkyl Cyclic Ketones in fragrances. Copyright © 2013 Elsevier Ltd. All rights reserved.

The Microwave Spectrum of Methyl Vinyl Ketone Revisited

Science.gov (United States)

Wilcox, David S.; Shirar, Amanda J.; Williams, Owen L.; Dian, Brian C.

2011-06-01

A chirped-pulse Fourier transform microwave spectrometer was used to record the rotational spectrum of methyl vinyl ketone (MVK, 3-butene-2-one) from 6 to 18.9 GHz. Two stable conformations were identified: the previously documented antiperiplanar (ap) conformer and synperiplanar (sp), which is reported for the first time in this microwave study. Methyl torsional analysis with XIAM resulted in V3 barrier heights of 433.8(1) and 376.6(2) Cm-1 for ap- and sp-MVK, respectively. Heavy atom isotopic species were detected in natural abundance allowing bond lengths and angles of the molecular frames to be calculated through Kraitchman analysis. A comparison with ab initio calculations is included.

EVALUATION OF PROPYLENE CARBONATE IN AIR LOGISTICS CENTER (ALC) DEPAINTING OPERATIONS

Science.gov (United States)

This report summarizes a two-phase, laboratory-scale screening study that evaluated solvent blends containing propylene carbonate (PC) as a potential replacement for methyl ethyl ketone (MEK) in aircraft radome depainting operations. The study was conducted at Oklahoma City Air L...

Synthesis of β-phenylchalcogeno-α, β-unsaturated esters, ketones and nitriles using microwave and solvent-free conditions

International Nuclear Information System (INIS)

Lenardao, Eder J.; Silva, Marcio S.; Mendes, Samuel R.; Azambuja, Francisco de; Jacob, Raquel G.; Perin, Gelson; Santos, Paulo Cesar Silva dos

2007-01-01

A simple, clean and efficient solvent-free protocol was developed for hydrochalcogenation of alkynes containing a Michael acceptor (ester, ketone and nitrile) with phenylchalcogenolate anions generated in situ from the respective diphenyl dichalcogenide (Se, Te, S), using alumina supported sodium borohydride. This efficient and improved method is general and furnishes the respective (Z)-β-phenylchalcogeno-α,β-unsaturated esters, ketones and nitriles, in good yield and higher selectivity, compared with those that use organic solvent and inert atmosphere. The use of microwave (MW) irradiation facilitates the procedure and accelerates the reaction. (author)

Elution behavior of poly(ethylene glycol) through poly(vinyl alcohol) gel column using several solvents as eluents

International Nuclear Information System (INIS)

Hirayama, Chuichi; Motozato, Yoshiaki; Matsumoto, Kazuaki.

1983-01-01

γ-Irradiated poly(vinyl alcohol) beads, which were sufficiently allowed to swell in water, were washed with methanol, and then were packed into column. Gel chromatography was performed using methanol, benzene, esters and ketones as eluents and poly(ethylene glycol) as a sample. When the elution was carried out using methanol and benzene as eluents, elution behavior of samples was ordinary. When ethyl formate, methyl acetate and ethyl propionate were used as eluents, samples were slightly adsorbed and the elution was delayed. In the case the elution was carried out using ethyl acetate, propyl acetate, butyl acetate and ethyl methyl ketone as eluents, samples were adsorbed strongly on the bed material, and the adsorption curve was analogous to the calibration curve using methanol as an eluent. Dried poly(vinyl alcohol) gel as a packing material, showed ordinary elution behaviors for the samples. The adsorption of poly(ethylene glycol) on the present bed material was attributed to the existence of hydrated water on poly(vinyl alcohol) gel matrix. (author)

Solvent exchange-induced in situ forming gel comprising ethyl cellulose-antimicrobial drugs.

Science.gov (United States)

Phaechamud, Thawatchai; Mahadlek, Jongjan

2015-10-15

Solvent-exchanged in situ forming gel is a drug delivery system which is in sol form before administration. When it contacts with the body fluid, then the water miscible organic solvent dissipates and water penetrates into the system, leading the polymer precipitation as in situ gel at the site of injection. The aim of this research was to study the parameters affecting the gel properties, drug release and antimicrobial activities of the in situ forming gels prepared from ethyl cellulose (EC) dissolved in N-methyl pyrrolidone (NMP) to deliver the antimicrobial agents (doxycycline hyclate, metronidazole and benzyl peroxide) for periodontitis treatment. The gel appearance, pH, viscosity, rheology, syringeability, gel formation, rate of water diffusion into the gels, in vitro degradation, drug release behavior and antimicrobial activities against Staphylococcus aureus, Escherichia coli, Candida albicans, Streptococcus mutans and Porphyrommonas gingivalis were determined. Increasing the amount of EC increased the viscosity of system while still exhibiting Newtonian flow and increased the work of syringeability whereas decreased the releasing of drug. The system transformed into the rigid gel formation after being injected into the simulated gingival crevicular fluid. The developed systems containing 5% w/w antimicrobial agent showed the antimicrobial activities against all test bacteria. Thus the developed solvent exchange-induced in situ forming gels comprising EC-antimicrobial drugs exhibited potential use for periodontitis treatment. Copyright © 2015 Elsevier B.V. All rights reserved.

Microstructural characterization of a novel methyl acrylate-ethyl acrylate copolymer system

Energy Technology Data Exchange (ETDEWEB)

Olivares, M.; Castano, V.M. [Instituto de Fisica, UNAM, A.P. 1-1010, Queretaro, Mexico (Mexico); Molina, J.P.; Vazquez, F. [Facultad de Quimica UAEMex, Paseo Tollocan esq. Paseo Colon, Toluca, Estado de Mexico (Mexico)

1998-12-31

A number of different compositions of a novel methyl acrylate-ethyl acrylate copolymer were prepared by emulsion polymerization with potassium persulfate as initiator. The compositions synthesized were: 100/0, 75/25, 50/50, 25/75 and 0/100 on weight of methyl acrylate/ethyl acrylate at different temperatures and concentrations of initiators. The effect of other conditions were also studied. The samples were analyzed by Transmission Electron Microscopy. It was found that the size of aggregates and dispersion on sizes are controlled by the synthesis conditions, result partially supported by light scattering. (Author)

Microstructural characterization of a novel methyl acrylate-ethyl acrylate copolymer system

International Nuclear Information System (INIS)

Olivares, M.; Castano, V.M.; Molina, J.P.; Vazquez, F.

1998-01-01

A number of different compositions of a novel methyl acrylate-ethyl acrylate copolymer were prepared by emulsion polymerization with potassium persulfate as initiator. The compositions synthesized were: 100/0, 75/25, 50/50, 25/75 and 0/100 on weight of methyl acrylate/ethyl acrylate at different temperatures and concentrations of initiators. The effect of other conditions were also studied. The samples were analyzed by Transmission Electron Microscopy. It was found that the size of aggregates and dispersion on sizes are controlled by the synthesis conditions, result partially supported by light scattering. (Author)

Reactivity of solvent alcohol on degradation of CFC113

International Nuclear Information System (INIS)

Nakagawa, Seiko

2003-01-01

1,1,2-Trichloro-trifluoroethane (CFC113) was dissolved in alkaline 1-butanol, 2-butanol, iso-butyl alcohol, and phenyl ethyl alcohol and irradiated with 60 Co gamma rays after purged with pure nitrogen gas. In all these solvents, the concentration of CFC113 and hydroxide ion decreased and that of chloride ion increased with a dose observed in 2-propanol solution. The reaction efficiency increases in order of 1-butanol< iso-butyl alcohol< phenyl ethyl alcohol<2-butanol<2-propanol. The solvent effect will depend on the binding energy of the αC-H of the alcohol molecule and electron affinity and dipole moment of the ketones or aldehydes produced from the alcohols

Ketone EC50 values in the Microtox test.

Science.gov (United States)

Chen, H F; Hee, S S

1995-03-01

The Microtox EC50 values for the following ketones are reported in the following homologous series: straight chain methyl ketones (acetone, 2-butanone, 2-pentanone, 2-hepatonone, 2-octanone, 2-decanone, and 2-tridecanone); methyl ketones substituted at one alpha carbon (3-methyl-2-butanone; 3,3-dimethyl-2-butanone); methyl substituted at two alpha carbons (2,4-dimethyl-3-pentanone; 2,2,4,4-tetramethyl-3-pentanone); phenyl groups replacing methyl in acetone (acetophenone; benzophenone); methyl groups substituted at the alpha carbons of cyclohexanone; and 2,3- 2,4-, and 2,5-hexanediones, most for the first time. While there were linear relationships between log EC50 and MW for the straight chain methyl ketones, and for methyl substitution at the alpha carbon for methyl ketones, there were no other linear relationships. As molecular weight increased, the EC50 values of soluble ketones decreased; as distance between two carbonyl groups decreased so too did EC50 values. Thus, for the ketones the geometry around the carbonyl group is an important determinant of toxicity as well as MW, water solubility, and octanol/water coefficient.

Synthesis of acetic acid by catalytic oxidation of butenes-2. Synthesis of acetic acid from sec. -butyl alcohol and methyl ethyl ketone in vapor-phase catalytic oxidation

Energy Technology Data Exchange (ETDEWEB)

Yamashita, T.; Matsuzawa, Y.; Ninagawa, S.

1977-11-01

Eleven binary catalysts containing vanadium pentoxide (V/sub 2/O/sub 5/), 17 binary catalysts containing cobalt oxide (Co/sub 3/O/sub 4/), and 18 ternary catalysts containing both V/sub 2/O/sub 5/ and Co/sub 3/O/sub 4/ were screened for the stepwise conversion of sec.-butanol to methyl ethyl ketone (MEK) and acetic acid. Of the binary catalysts, 4:1 Rh/V and Co/V binary oxides gave the best acetic acid yields. With the Co/V catalyst, the selectivity for MEK increased rapidly as the cobalt content of the catalyst increased above 50%, reaching 81% at 226/sup 0/C and 90% conversion on 9:1 Co/V oxide. The 9:1 Co/V catalyst also yielded acetaldehyde from ethanol with 98% selectivity at 210/sup 0/C and acetone from isopropanol with 98% selectivity at 200/sup 0/C, but dehydrated tert.-butanol to isobutene. V/Cr and V/Sb binary oxides were the most effective catalysts for the oxidation of MEK to acetic acid, with 78-88% selectivities at 100% conversion at 260/sup 0/C. Of the ternary oxides tested for the one-step conversion of sec.-butanol to acetic acid, a 6:2:2 Co/V/Al catalyst gave best results, (i.e., 34% selectivity for acetic acid (45% for total acids) at 100% conversion and 68% selectivity (90% for total acids) at 50Vertical Bar3< conversion). Graphs, tables, and 21 references.

Chemodynamics of Methyl Parathion and Ethyl Parathion: Adsorption Models for Sustainable Agriculture

Science.gov (United States)

Rafique, Uzaira; Balkhair, Khaled S.; Ashraf, Muhammad Aqeel

2014-01-01

The toxicity of organophosphate insecticides for nontarget organism has been the subject of extensive research for sustainable agriculture. Pakistan has banned the use of methyl/ethyl parathions, but they are still illegally used. The present study is an attempt to estimate the residual concentration and to suggest remedial solution of adsorption by different types of soils collected and characterized for physicochemical parameters. Sorption of pesticides in soil or other porous media is an important process regulating pesticide transport and degradation. The percentage removal of methyl parathion and ethyl parathion was determined through UV-Visible spectrophotometer at 276 nm and 277 nm, respectively. The results indicate that agricultural soil as compared to barren soil is more efficient adsorbent for both insecticides, at optimum batch condition of pH 7. The equilibrium between adsorbate and adsorbent was attained in 12 hours. Methyl parathion is removed more efficiently (by seven orders of magnitude) than ethyl parathion. It may be attributed to more available binding sites and less steric hindrance of methyl parathion. Adsorption kinetics indicates that a good correlation exists between distribution coefficient (Kd) and soil organic carbon. A general increase in Kd is noted with increase in induced concentration due to the formation of bound or aged residue. PMID:24689059

Chemodynamics of Methyl Parathion and Ethyl Parathion: Adsorption Models for Sustainable Agriculture

Directory of Open Access Journals (Sweden)

Noshabah Tabassum

2014-01-01

Full Text Available The toxicity of organophosphate insecticides for nontarget organism has been the subject of extensive research for sustainable agriculture. Pakistan has banned the use of methyl/ethyl parathions, but they are still illegally used. The present study is an attempt to estimate the residual concentration and to suggest remedial solution of adsorption by different types of soils collected and characterized for physicochemical parameters. Sorption of pesticides in soil or other porous media is an important process regulating pesticide transport and degradation. The percentage removal of methyl parathion and ethyl parathion was determined through UV-Visible spectrophotometer at 276 nm and 277 nm, respectively. The results indicate that agricultural soil as compared to barren soil is more efficient adsorbent for both insecticides, at optimum batch condition of pH 7. The equilibrium between adsorbate and adsorbent was attained in 12 hours. Methyl parathion is removed more efficiently (by seven orders of magnitude than ethyl parathion. It may be attributed to more available binding sites and less steric hindrance of methyl parathion. Adsorption kinetics indicates that a good correlation exists between distribution coefficient (Kd and soil organic carbon. A general increase in Kd is noted with increase in induced concentration due to the formation of bound or aged residue.

Effect of solvent alcohol on degradation of chlorinated hydrocarbons by γ-irradiation

International Nuclear Information System (INIS)

Nakagawa, Seiko

2002-01-01

1,1,2-Trichloro-trifluoroethane (CFC113) was dissolved in alkaline 1-butanol, 2-butanol, iso-butyl alcohol, and phenyl ethyl alcohol and irradiated with 60 Co gamma rays after being purged with pure nitrogen gas. In all these solvents, the concentration of CFC113 and hydroxide ion decreased and that of chloride ion increased with a dose observed in 2-propanol solution. The reaction efficiency increases in the following order: 1-butanol < iso-butyl alcohol < phenyl ethyl alcohol < 2-butanol < 2-propanol. The solvent effect will depend on the binding energy of the αC-H of the alcohol molecule and electron affinity and dipole moment of the ketones or aldehydes produced from the alcohols. (author)

Preparation and characterization of poly (methyl methacrylate) and sulfonated poly (ether ether ketone) blend ultrafiltration membranes for protein separation applications

International Nuclear Information System (INIS)

Arthanareeswaran, G.; Thanikaivelan, P.; Raajenthiren, M.

2009-01-01

Poly (methyl methacrylate) (PMMA) and poly (methyl methacrylate)/sulfonated poly (ether ether ketone) (SPEEK) blend membranes were prepared by phase inversion technique in various composition using N,N'-dimethylformamide as solvent. The prepared membranes were characterized in terms of pure water flux, water content, porosity and thermal stability. The addition of SPEEK to the casting solution resulted in membranes with high pure water flux, water content, porosity and slightly low thermal stability. The cross sectional views of the blend membranes under electron microscope confirm the porosity and water flux results. The effect of the addition of SPEEK into the PMMA matrix on the extent of bovine serum albumin (BSA) separation was studied. It was found that the permeate flux increased significantly while the rejection of BSA from aqueous solution reduced moderately during ultrafiltration (UF) process. The effect was attributed to the increase in porosity and charge of the membrane due to the addition of SPEEK into the PMMA blend solution

Additional conformer observed in the microwave spectrum of methyl vinyl ketone

Science.gov (United States)

Wilcox, David S.; Shirar, Amanda J.; Williams, Owen L.; Dian, Brian C.

2011-05-01

A chirped-pulse Fourier transform microwave spectrometer was used to record the rotational spectrum of methyl vinyl ketone (MVK, 3-butene-2-one). Two stable conformations were identified: the previously documented antiperiplanar (ap) conformer and synperiplanar (sp), which is reported for the first time in this microwave study. Methyl torsional analysis resulted in V3 barrier heights of 433.8(1) and 376.6(2) cm-1 for ap- and sp-MVK, respectively. Heavy atom isotopic species of both conformers were detected in natural abundance allowing bond lengths and angles of the molecular frames to be calculated through Kraitchman analysis. A comparison with ab initio calculations is included.

Glucose utilization in the brain during acute seizure is a useful biomarker for the evaluation of anticonvulsants: effect of methyl ethyl ketone in lithium-pilocarpine status epilepticus rats

International Nuclear Information System (INIS)

Yamada, Akifumi; Momosaki, Sotaro; Hosoi, Rie; Abe, Kohji; Yamaguchi, Masatoshi; Inoue, Osamu

2009-01-01

Enhancement of glucose utilization in the brain has been well known during acute seizure in various kinds of animal model of epilepsy. This enhancement of glucose utilization might be related to neural damage in these animal models. Recently, we found that methyl ethyl ketone (MEK) had both anticonvulsive and neuroprotective effects in lithium-pilocapine (Li-pilo) status epilepticus (SE) rat. In this article, we measured the uptake of [ 14 C]2-deoxyglucose ([ 14 C]DG) in the Li-pilo SE and Li-pilo SE with MEK rat brain in order to assess whether the glucose utilization was a useful biomarker for the detection of efficacy of anticonvulsive compounds. Significant increase of [ 14 C]DG uptake (45 min after the injection) in the cerebral cortex, hippocampus, amygdala and thalamus during acute seizure induced by Li-pilo were observed. On the other hand, the initial uptake of [ 14 C]DG (1 min after the injection) in the Li-pilo SE rats was not different from the control rats. Therefore, the enhancement of glucose metabolism during acute seizure was due to the facilitation of the rate of phosphorylation process of [ 14 C]DG in the brain. Pretreatment with MEK (8 mmol/kg) completely abolished the enhancement of glucose utilization in the Li-pilo SE rats. The present results indicated that glucose utilization in the brain during acute seizure might be a useful biomarker for the evaluation of efficacy of anticonvulsive compounds.

Glucose utilization in the brain during acute seizure is a useful biomarker for the evaluation of anticonvulsants: effect of methyl ethyl ketone in lithium-pilocarpine status epilepticus rats

Energy Technology Data Exchange (ETDEWEB)

Yamada, Akifumi [Division of Health Sciences, Graduate School of Medicine, Osaka University, Osaka, 565-0871 (Japan); Momosaki, Sotaro; Hosoi, Rie [Division of Health Sciences, Graduate School of Medicine, Osaka University, Osaka, 565-0871 (Japan); Abe, Kohji [Division of Health Sciences, Graduate School of Medicine, Osaka University, Osaka, 565-0871 (Japan); Developmental Research Laboratories, Shionogi and Co., Ltd., Toyonaka, Osaka, 561-0825 (Japan); Yamaguchi, Masatoshi [Faculty of Pharmaceutical Sciences, Fukuoka University, Johnan, Fukuoka 814-0180 (Japan); Inoue, Osamu [Division of Health Sciences, Graduate School of Medicine, Osaka University, Osaka, 565-0871 (Japan)

2009-11-15

Enhancement of glucose utilization in the brain has been well known during acute seizure in various kinds of animal model of epilepsy. This enhancement of glucose utilization might be related to neural damage in these animal models. Recently, we found that methyl ethyl ketone (MEK) had both anticonvulsive and neuroprotective effects in lithium-pilocapine (Li-pilo) status epilepticus (SE) rat. In this article, we measured the uptake of [{sup 14}C]2-deoxyglucose ([{sup 14}C]DG) in the Li-pilo SE and Li-pilo SE with MEK rat brain in order to assess whether the glucose utilization was a useful biomarker for the detection of efficacy of anticonvulsive compounds. Significant increase of [{sup 14}C]DG uptake (45 min after the injection) in the cerebral cortex, hippocampus, amygdala and thalamus during acute seizure induced by Li-pilo were observed. On the other hand, the initial uptake of [{sup 14}C]DG (1 min after the injection) in the Li-pilo SE rats was not different from the control rats. Therefore, the enhancement of glucose metabolism during acute seizure was due to the facilitation of the rate of phosphorylation process of [{sup 14}C]DG in the brain. Pretreatment with MEK (8 mmol/kg) completely abolished the enhancement of glucose utilization in the Li-pilo SE rats. The present results indicated that glucose utilization in the brain during acute seizure might be a useful biomarker for the evaluation of efficacy of anticonvulsive compounds.

21 CFR 172.225 - Methyl and ethyl esters of fatty acids produced from edible fats and oils.

Science.gov (United States)

2010-04-01

... from edible fats and oils. 172.225 Section 172.225 Food and Drugs FOOD AND DRUG ADMINISTRATION... Methyl and ethyl esters of fatty acids produced from edible fats and oils. Methyl esters and ethyl esters of fatty acids produced from edible fats and oils may be safely used in food, subject to the...

Miscibility and Hydrogen Bonding in Blends of Poly(4-vinylphenol/Poly(vinyl methyl ketone

Directory of Open Access Journals (Sweden)

Hana Bourara

2014-10-01

Full Text Available The miscibility and phase behavior of poly(4-vinylphenol (PVPh with poly(vinyl methyl ketone (PVMK was investigated by differential scanning calorimetry (DSC, Fourier transform infrared spectroscopy (FTIR and scanning electron microscopy (SEM. It was shown that all blends of PVPh/PVMK are totally miscible. A DSC study showed the apparition of a single glass transition (Tg over their entire composition range. When the amount of PVPh exceeds 50% in blends, the obtained Tgs are found to be significantly higher than those observed for each individual component of the mixture, indicating that these blends are capable of forming interpolymer complexes. FTIR analysis revealed the existence of preferential specific interactions via hydrogen bonding between the hydroxyl and carbonyl groups, which intensified when the amount of PVPh was increased in blends. Furthermore, the quantitative FTIR study carried out for PVPh/PVMK blends was also performed for the vinylphenol (VPh and vinyl methyl ketone (VMK functional groups. These results were also established by scanning electron microscopy study (SEM.

Two Zn and Hg bromide salts based on 1-ethyl-3-methyl imidazolium ionic liquid: Ionothermal synthesis, structures and supramolecular organization

Directory of Open Access Journals (Sweden)

Xiu-Cheng Zhang

2012-12-01

Full Text Available Two Zn(II and Hg(II bromide salts, [EMI]2[ZnBr4] (1 and [EMI][HgBr3] (2, have been synthesized under ionothermal conditions using 1-ethyl-3-methyl imidazolium bromide ([EMI]Br as solvents. 1 consists of tetrahedral anion [ZnBr4]2− and 2 consists of 1D double chain locating in the cavities surrounded by [EMI]+ cations. Both compounds exhibit 3D supramolecular architectures organized by the C-H•••Br hydrogen bondings and alkyl-alkyl interactions.DOI: http://dx.doi.org/10.4314/bcse.v26i3.9

Alkylation of deoxyribonucleic acid by carcinogens dimethyl sulphate, ethyl methanesulphonate, N-ethyl-N-nitrosourea and N-methyl-N-nitrosourea

International Nuclear Information System (INIS)

Swenson, D.H.; Lawley, P.D.

1978-01-01

The ethyl phosphotriester of thymidylyl(3'-5')thymidine, dTp((Et) dT, was identified as a product from the reaction of DNA with N-ethyl-N-nitrosourea. Enzymic degradation to yield alkyl phosphotriesters from DNA alkylated by this carcinogen, and by N-methyl-N-nitrosourea, dimethyl sulphate and ethyl methanesulphonate was studied quantitatively, and the relative yields of the triesters dTp(Alk)dT were determined. The relative reactivity of the phosphodiester group dTpdT to each of the four carcinogens was thus obtained, and compared with that of DNA overall, or with that of the N-7 atom of guanine in DNA. The results are related to steric factors, and the electrophilic character of each carcinogen. (author)

Potential impact of methyl isobutyl ketone (MIBK) on phenols degradation in an UASB reactor and its degradation properties.

Science.gov (United States)

Wang, Wei; Yang, Kai; Sierra, Julian Muñoz; Zhang, Xuedong; Yuan, Shoujun; Hu, Zhenhu

2017-07-05

Methyl isobutyl ketone (MIBK) as a solvent is extensively used for the phenols extraction from the wastewater, so it is unavoidable to expose in the effluent due to the solubility and leakage problem. The present study evaluated the impact of MIBK on phenols degradation in an UASB reactor and analyzed its degradation properties. The results indicated that the continuous dosing (0.1gL -1 ) and impact (10gL -1 ) of MIBK had limited effect on phenols removal (1-2% reduction) in the UASB reactor, but the specific methanogenic activity (SMA) values of sludge decreased by 45-75% after MIBK exposure. Anaerobic degradation rate of MIBK fitted well to a pseudo-first-order kinetic equation with respect to the initial concentration of 35mgL -1 (k=0.0115h -1 , R 2 =0.9664). Furthermore, the relative methane generation rate constants of MIBK were 0.00816, 0.00613, 0.00273, and 0.00207d -1 at the initial concentrations of 0.1, 0.5, 5, and 10gL -1 , respectively. MIBK showed higher inhibitory effect on the methanogenesis than on phenols degradation. This study pointed out that the industrial installations should consider the influence of solvent on anaerobic treatment of phenolic wastewater. Copyright © 2017 Elsevier B.V. All rights reserved.

Elimination of ketone vapors by adsorption on spherical MCM-41 and MCM-48 silicas decorated with thermally activated poly(furfuryl alcohol)

Energy Technology Data Exchange (ETDEWEB)

Machowski, Kamil [Faculty of Chemistry, Jagiellonian University, Ingardena 3, 30-060 Kraków (Poland); Kuśtrowski, Piotr, E-mail: kustrows@chemia.uj.edu.pl [Faculty of Chemistry, Jagiellonian University, Ingardena 3, 30-060 Kraków (Poland); Dudek, Barbara [Faculty of Chemistry, Jagiellonian University, Ingardena 3, 30-060 Kraków (Poland); Michalik, Marek [Institute of Geological Sciences, Jagiellonian University, Oleandry 2a, 30-063 Kraków (Poland)

2015-09-01

Spherical MCM-41 and MCM-48 silicas with different arrangements of mesopores were synthesized in a water–alcohol solution of surfactant by the hard-templating method. The pore structure and morphology of the obtained materials were confirmed by powder X-ray diffraction (XRD), low-temperature adsorption of nitrogen and scanning electron microscopy (SEM). The surface of mesoporous silicas was decorated with small amounts of poly(furfuryl alcohol) (PFA), which was introduced by the precipitation polymerization and subsequently thermally activated at 523 K to form stable C=O surface species detected by FTIR spectroscopy. The adsorption capacity of the PFA/silica composites in the elimination of various ketone (acetone, methyl-ethyl ketone and methyl-isobutyl ketone) vapors was compared to the effectiveness of pristine silicas. It was found that the modification of silicas by thermally degraded PFA enhanced their adsorption capacity. This effect was attributed to the appearance of another type of surface centers (namely carbonyl groups), which beside silanols interact with ketone molecules via hydrogen bonds. DRIFT spectra showed that a ketone molecule is bonded on silanol species in its keto form, whereas on carbonyl functionalities in enol one. - Highlights: • Surface of spherical MCM-type silicas was decorated with poly(furfuryl alcohol). • Thermal degradation of deposited polymer resulted in formation of C=O species. • Carbonyl groups enhanced adsorption capacity of MCM-41 and MCM-48 silicas. • Adsorption of ketones in enol or keto forms was revealed by DRIFT measurements.

Elimination of ketone vapors by adsorption on spherical MCM-41 and MCM-48 silicas decorated with thermally activated poly(furfuryl alcohol)

International Nuclear Information System (INIS)

Machowski, Kamil; Kuśtrowski, Piotr; Dudek, Barbara; Michalik, Marek

2015-01-01

Spherical MCM-41 and MCM-48 silicas with different arrangements of mesopores were synthesized in a water–alcohol solution of surfactant by the hard-templating method. The pore structure and morphology of the obtained materials were confirmed by powder X-ray diffraction (XRD), low-temperature adsorption of nitrogen and scanning electron microscopy (SEM). The surface of mesoporous silicas was decorated with small amounts of poly(furfuryl alcohol) (PFA), which was introduced by the precipitation polymerization and subsequently thermally activated at 523 K to form stable C=O surface species detected by FTIR spectroscopy. The adsorption capacity of the PFA/silica composites in the elimination of various ketone (acetone, methyl-ethyl ketone and methyl-isobutyl ketone) vapors was compared to the effectiveness of pristine silicas. It was found that the modification of silicas by thermally degraded PFA enhanced their adsorption capacity. This effect was attributed to the appearance of another type of surface centers (namely carbonyl groups), which beside silanols interact with ketone molecules via hydrogen bonds. DRIFT spectra showed that a ketone molecule is bonded on silanol species in its keto form, whereas on carbonyl functionalities in enol one. - Highlights: • Surface of spherical MCM-type silicas was decorated with poly(furfuryl alcohol). • Thermal degradation of deposited polymer resulted in formation of C=O species. • Carbonyl groups enhanced adsorption capacity of MCM-41 and MCM-48 silicas. • Adsorption of ketones in enol or keto forms was revealed by DRIFT measurements.

Decaffeination process characteristic of Robusta coffee in single column reactor using ethyl acetate solvent

Directory of Open Access Journals (Sweden)

Sukrisno Widyotomo

2009-08-01

Full Text Available Consumers drink coffee not as nutrition source, but as refreshment drink. For coffee consumers who have high tolerance for caffeine, coffee may warm up and refresh their bodies. High caffeine content in coffee beans may cause several complaints to consumers who are susceptible to caffeine. One of the efforts, for coffee market expansion is product diversification to decaffeinated coffee. Decaffeination process is one of process to reduce caffeine content from agricultural products. Indonesian Coffee and Cocoa Research Institute in collaboration with Bogor Agricultural University has developed a single column reactor for coffee beans decaffeination. The aim of this research is to study process characteristic of coffee decaffeination in single column reactor using ethyl acetate (C4H8O2 solvent. Treatments applicated in the research were time and temperature process. Temperature treatment were 50—60OC, 60—70OC, 70—80OC, 80—90OC and 90—100OC. Time treatment were 2 h, 4 h, 6 h, 8 h, 10 h, and 12 h Size of Robusta coffee beans used were less than 5.5 mm (A4, between 5.5 mm and 6.5 mm (A3, between 6.5 mm and 7.5 mm (A2, and more than 7.5 mm (A1. The result showed that decaffeination process with ethyl acetate solvent will be faster when its temperature was higher and smaller bean size. For bean size less than 5,5 mm, decaffeination process by 10% ethyl acetat can be done 8—10 hours in 90—100OC solvent temperature or 12 hours in 60—70OC solvent temperature for 0.3% caffein content. Organoleptic test showed that 90—100OC temperature solvent treatment decreased coffee flavor, which aroma, bitterness and body values were 1.9 each . Key words : Coffee, caffeine, decaffeination, quality, single column.

Polymer Film Dewetting by Water/Surfactant/Good-Solvent Mixtures: A Mechanistic Insight and Its Implications for the Conservation of Cultural Heritage.

Science.gov (United States)

Baglioni, Michele; Montis, Costanza; Chelazzi, David; Giorgi, Rodorico; Berti, Debora; Baglioni, Piero

2018-06-18

Aqueous nanostructured fluids (NSFs) have been proposed to remove polymer coatings from the surface of works of art; this process usually involves film dewetting. The NSF cleaning mechanism was studied using several techniques that were employed to obtain mechanistic insight on the interaction of a methacrylic/acrylic copolymer (Paraloid B72) film laid on glass surfaces and several NSFs, based on two solvents and two surfactants. The experimental results provide a detailed picture of the dewetting process. The gyration radius and the reduction of the T g of Paraloid B72 fully swollen in the two solvents is larger for propylene carbonate than for methyl ethyl ketone, suggesting higher mobility of polymer chains for the former, while a nonionic alcohol ethoxylate surfactant was more effective than sodium dodecylsulfate in favoring the dewetting process. FTIR 2D imaging showed that the dewetting patterns observed on model samples are also present on polymer-coated mortar tiles when exposed to NSFs. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

The Extraction Process of Trimethyl Xanthina in Vitro Culture of Callus Camellia Sinensis with ethyl Acetate Solvent

Directory of Open Access Journals (Sweden)

Sutini

2016-01-01

Full Text Available Trimethyl xanthina is one of the compounds contained bioactive culture in vitro Cammelia sinensis callus which is widely used in the field of food, beverage, agriculture and health industries. The presence of trimethyl xanthina on food, beverages and health is needed in a certain amount depending on the use which is achieved by the user. To get a certain amount of trimethyl xanthina from callus culture of Cammelia sinensis, the extraction process is performed on the water solvent, as well as non-solvent water / organic solvent such as ethyl acetate. The purpose of this study was to obtain profile of trimethyl xanthina in the extraction of Cammelia sinensis callus. The experimental methods used consisted of dissolution, filtration, extraction with water solvent and ethyl acetate, then followed by identification of trimethyl xanthina using HPLC. The results shows the profile form of trimethyl xanthina of Cammelia sinensis callus have similarities with the standard form of trimethyl xanthina.

Solubility and solvation of alkali metal perchlorates, tetramethyl and tetraethylammonium in aqua-ketone solvents

International Nuclear Information System (INIS)

Kireev, A.A.; Pak, T.G.; Bezuglyj, V.D.

1998-01-01

The KClO 4 , RbClO 4 , CsClO 4 , (CH 3 ) 4 NClO 4 , (C 2 H 5 ) 4 NClO 4 solubility in water and water-acetone, water-methylethylketone mixtures is determined through the method of isothermal saturation at 298.15 K. Dissociation constants of alkali metals perchlorates in acetone and its 90% mixtures (by volume) are determined conductometrically. Solubility products and standard energies of the Gibbs transfer of the studied electrolytes from water into water-acetone and water-methylethylketone solvents. It is established that the Gibbs standard energies of Na + , K + , Rb + and Cs + cations transfer from water to water-ketone solvents are close to each other. It is shown that the effect of acetone and methylethylketone on solvation of the studied electrolytes is practically similar

Standardization of solvent extraction procedure for determination of uranium in seawater

International Nuclear Information System (INIS)

Sukanta Maity; Sahu, S.K.; Pandit, G.G.

2015-01-01

Solvent extraction procedure using ammonium pyrolidine dithiocarbamate complexing agent in methyl isobutyl ketone organic phase and acid exchange back-extraction is described for the simultaneous quantitative pre-concentration of uranium in seawater followed by its determination by differential pulse adsorptive stripping voltammetry. Solvent extraction time is optimized for extraction of uranium from seawater. Solvent extraction efficiency for uranium in seawater at different pH was carried out. The method gives a recovery of 98 ± 2 % for 400 mL sample at pH 3.0 ± 0.02, facilitating the rapid and interference free analysis of seawater samples. (author)

Possible interferences of mercury sulfur compounds with ethylated and methylated mercury species using HPLC-ICP-MS

International Nuclear Information System (INIS)

Wilken, R.D.; Nitschke, F.; Falter, R.

2003-01-01

The HPLC-ICP-MS coupling technique is able to separate and detect methyl, ethyl and inorganic mercury isotopes specifically. An identification of ethyl mercury(+) is not possible when the widely used sodium tetraethylborate derivatisation method in combination with GC-AFS/AAS or ICP-MS techniques is performed because it contains ethyl groups. An unidentified compound with the same retention time as ethyl mercury was found in the HPLC chromatograms of industrial sewage samples and humic-rich soils of microcosm experiments after applying water vapour distillation. We also observed such unidentified peaks in samples of heavily contaminated sites in Eastern Germany, separated by HPLC fractionation only. In the experiments described, different mercury sulfur adducts were synthesised and tested for their retention times in the HPLC-ICP-MS system. It was found that the compound CH 3 -S-Hg + showed the same retention time as the ethyl mercury standard. It is therefore possible that ethyl mercury detected in chromatography by comparison of the retention time could also be due to an adduct of a sulfur compound and a mercury species. CH 3 -S-Hg + should be tested in other chromatographic mercury speciation methods for this effect. This work can also be regarded as a contribution to the discussion of artificially occurring methyl mercury in sediments during sample preparation. (orig.)

Synthesis of (R,S)-[2,3-13C2]-1-(1'-methyl-2'-pyrrolidinyl)propan-2-one; {(R,S)-[2',3'-13C2]hygrinePound right bracePound

International Nuclear Information System (INIS)

Abraham, T.W.; Leete, Edward

1996-01-01

2-Ethoxy-1-methyl-5-pyrrolidinone (1) was reacted with ethyl [3,4- 13 C 2 ]-acetoacetate (2) in the presence of TiCl 4 to give ethyl [3,4- 13 C 2 ]-2-(1'-methyl-5'-oxo-2'-pyrrolidinyl)-3-oxobutanoate (3) in 85% yield. Decarboethoxylation of ethyl [3,4- 13 C 2 ]-2-(1'-methyl-5'-oxo-2'-pyrrolidinyl)-3-oxobutan-oate (3) was accomplished using NaCl and H 2 O in DMSO to give (R,S)-[2,3- 13 C 2 ]-1-(1'-methyl-5'-oxo-2'-pyrrolidinyl)propan-2-o ne (4) in 91% yield. Protection of the ketone as a ketal (ethylene glycol, H + ), followed by reduction of the amide to the amine using LiAlH 4 and subsequent deprotection of the ketal gave (R,S)-[2,3- 13 C 2 ]-1-(1'-methyl-2'-pyrrolidinyl)propan-2-one ((R,s)-[2', 3'- 13 C 2 ]Hygrine) (8) in 78% yield. (61% overall yield from ethyl [3,4- 13 C 2 ]acetoacetate). (Author)

Asymmetric reduction of ketones with catecholborane using 2,6-BODOL complexes of titanium(IV) as catalysts.

Science.gov (United States)

Sarvary, I; Almqvist, F; Frejd, T

2001-05-18

Reductions performed with Ti(IV) complexes of ligands based on bicyclo[2.2.2]octane diols 5 and 6 are effective catalysts in the reduction of prochiral ketones to optically active alcohols, with catecholborane as the reducing agent. Methyl ketones are favored and enantiomeric excesses (ee) of octanone, which gave 2-octanol in 87% ee. Further details of the method were examined, for example, temperature, solvent composition, amount of molecular sieves (4 A), and catecholborane quality, as well as the sensitivity of the ligands towards acids. NMR spectroscopic methods were used to gain some insight into the complexes formed between the ligands and [Ti(OiPr)4]. A dimeric structure is proposed for the pre-catalyst.

Novel one-pot process for the synthesis of ethyl 2-imino-4-methyl-2,3-dihydrothiazole-5-carboxylates

Directory of Open Access Journals (Sweden)

Beyzaei Hamid

2015-01-01

Full Text Available A facile one-pot two-step process for the synthesis of ethyl 2-imino-4-methyl-2,3-dihydrothiazole-5-carboxylates via the cyclocondensation of ethyl 2-thiocyanatoacetoacetate with a variety of hydrazine and hydrazide derivatives has been developed. Ethyl 2-thiocyanatoacetoacetate itself has been synthesized as intermediate from the reaction of ethyl 2-chloroacetoacetate with potassium thiocyanate (KSCN. The molecular structures of these newly synthesized compounds were elucidated on the basis of elemental analysis and spectral data.

Synthesis and thermal behavior of new organometallic poly ketones and co-poly ketones based on diferrocenylidene piperidone

International Nuclear Information System (INIS)

Aly, K.I.

2005-01-01

A new interesting category of organometallic poly ketones and copolyketones were synthesized via Friedel - Crafts reaction through the polymerization of 2,6-[Bis (2-ferrocenyl )methylene] N-methylpiperidone (II) with different diacid chlorides. The model compound was synthesized by reacting the monomer (II) with benzoyl chloride and characterized by HNMR, IR and elemental analyses. The poly ketones and copolyketones were insoluble in most organic solvents but soluble easily in protic solvents. The thermal properties of these poly ketones and copolyketones were evaluated and correlated to their structural units by TGA and DSC measurements, and had inherent viscosity 0.34-0.52 dl g-1. Moreover, the electrical conductivity of one of the poly ketones, as selected example, Va and copolyketone VI were investigated above the temperature range (300-500 K) and showed that it followed an Arrhenius equation with activation energy 2.09 eV, also the morphological properties of selected examples of poly-and copolyketones were detected by SEM

Sulphur and oxygen sequestration of n-C 37 and n-C 38 unsaturated ketones in an immature kerogen and the release of their carbon skeletons during early stages of thermal maturation

Science.gov (United States)

Koopmans, Martin P.; Schaeffer-Reiss, Christine; de Leeuw, Jan W.; Lewan, Michael D.; Maxwell, James R.; Schaeffer, Philippe; Sinninghe Damsté, Jaap S.

1997-06-01

Sedimentary rock from the Gessoso-solfifera Formation (Messinian) in the Vena del Gesso Basin (northern Italy) containing immature ( Ro = 0.25%) S-rich organic matter was artificially matured by hydrous pyrolysis at temperatures from 160 to 330°C for 72 h to study the diagenetic fate of n-C 37 and n-C 38 di- and tri-unsaturated methyl and ethyl ketones (alkenones) biosynthesised by several prymnesiophyte algae. During early diagenesis, the alkenones are incorporated into the kerogen by both sulphur and oxygen cross-linking as indicated by chemical degradation experiments with the kerogen of the unheated sample. Heating at temperatures between 160 and 260°C, which still represents early stages of thermal maturation, produces large amounts (up to 1 mg/g TOC) of S-bound, O-bound, and both S- and O-bound n-C 37 and n-C 38 skeletons, saturated n-C 37 and n-C38 methyl, ethyl, and mid-chain ketones, C 37 and C 38 mid-chain 2,5-di- n-alkylthiophenes, C 37 and C 38 1,2-di- n-alkylbenzenes, and C 37 and C 38n-alkanes. With increasing thermal maturation, three forms of the n-C 37 and n-C 38 skeletons are relatively stable (saturated hydrocarbons, 1,2-di- n-alkylbenzenes and saturated ketones), whereas the S- and O-bound skeletons are relatively labile. These results suggest that in natural situations saturated ketones with an n-C 37 and n-C 38 skeleton can be expected as well as the corresponding hydrocarbons.

Sulphur and oxygen sequestration of n-C37 and n-C38 unsaturated ketones in an immature kerogen and the release of their carbon skeletons during early stages of thermal maturation

Science.gov (United States)

Koopmans, M.P.; Schaeffer-Reiss, C.; De Leeuw, J. W.; Lewan, M.D.; Maxwell, J.R.; Schaeffer, P.; Sinninghe, Damste J.S.

1997-01-01

Sedimentary rock from the Gessoso-solfifera Formation (Messinian) in the Vena del Gesso Basin (northern Italy) containing immature (Ro = 0.25%) S-rich organic matter was artificially matured by hydrous pyrolysis at temperatures from 160 to 330??C for 72 h to study the diagenetic fate of n-C37 and n-C38 di-and tri-unsaturated methyl and ethyl ketones (alkenones) biosynthesised by several prymnesiophyte algae. During early diagenesis, the alkenones are incorporated into the kerogen by both sulphur and oxygen cross-linking as indicated by chemical degradation experiments with the kerogen of the unheated sample. Heating at temperatures between 160 and 260??C, which still represents early stages of thermal maturation, produces large amounts (up to 1 mg/g TOC) of S-bound, O-bound, and both S-and O-bound n-C37 and n-C38 skeletons, saturated n-C37 and n-C38 methyl, ethyl, and mid-chain ketones, C37 and C38 mid-chain 2,5-di-n-alkylthiophenes, C37 and C38 1,2-di-n-alkylbenzenes, and C37 and C38 n-alkanes. With increasing thermal maturation, three forms of the n-C37 and n-C38 skeletons are relatively stable (saturated hydrocarbons, 1,2-di-n-alkylbenzenes and saturated ketones), whereas the S-and O-bound skeletons are relatively labile. These results suggest that in natural situations saturated ketones with an n-C37 and n-C38 skeleton can be expected as well as the corresponding hydrocarbons. Copyright ?? 1997 Elsevier Science Ltd.

A solvent-extraction module for cyclotron production of high-purity technetium-99m.

Science.gov (United States)

Martini, Petra; Boschi, Alessandra; Cicoria, Gianfranco; Uccelli, Licia; Pasquali, Micòl; Duatti, Adriano; Pupillo, Gaia; Marengo, Mario; Loriggiola, Massimo; Esposito, Juan

2016-12-01

The design and fabrication of a fully-automated, remotely controlled module for the extraction and purification of technetium-99m (Tc-99m), produced by proton bombardment of enriched Mo-100 molybdenum metallic targets in a low-energy medical cyclotron, is here described. After dissolution of the irradiated solid target in hydrogen peroxide, Tc-99m was obtained under the chemical form of 99m TcO 4 - , in high radionuclidic and radiochemical purity, by solvent extraction with methyl ethyl ketone (MEK). The extraction process was accomplished inside a glass column-shaped vial especially designed to allow for an easy automation of the whole procedure. Recovery yields were always >90% of the loaded activity. The final pertechnetate saline solution Na 99m TcO 4 , purified using the automated module here described, is within the Pharmacopoeia quality control parameters and is therefore a valid alternative to generator-produced 99m Tc. The resulting automated module is cost-effective and easily replicable for in-house production of high-purity Tc-99m by cyclotrons. Copyright © 2016 Elsevier Ltd. All rights reserved.

Solvent effect on thermodynamics of Ag(I) coordination to tripodal polypyridine ligands

DEFF Research Database (Denmark)

Del Piero, Silvia; Melchior, Andrea; Menotti, Davide

2009-01-01

  An investigation on the thermodynamics of complex formation between Ag(I) ion and different tripodal ligands (tris[(2-pyridyl)methyl]amine) (TPA) and 6,6'-bis[bis(2-pyridylmethyl)aminomethyl]-2,2'-bipyridine (BTPA) has been carried out in the aprotic solvents dimethylsulfoxide (DMSO) and dimeth......  An investigation on the thermodynamics of complex formation between Ag(I) ion and different tripodal ligands (tris[(2-pyridyl)methyl]amine) (TPA) and 6,6'-bis[bis(2-pyridylmethyl)aminomethyl]-2,2'-bipyridine (BTPA) has been carried out in the aprotic solvents dimethylsulfoxide (DMSO......)ethyl)amine  (Me3TREN) as a result of  combination of structural rigidity of TPA and lower s-donor ability of pyridinic moieties with respect to primary and secondary amines. The same trend is found if the stability of Ag(I) complex with TPA is compared with that of tris(2-(dimethylamino)ethyl)amine  (ME6TREN...... is largely influenced by the different solvational properties of the solvents towards Ag(I) ion rather than by the significative difference in the dielectric constants. Udgivelsesdato: Oktober...

Room Temperature Reactivity Of Silicon Nanocrystals With Solvents: The Case Of Ketone And Hydrogen Production From Secondary Alcohols: Catalysis?

KAUST Repository

El Demellawi, Jehad K.; Holt, Christopher; Abou-Hamad, Edy; Al-Talla, Zeyad; Saih, Youssef; Chaieb, Saharoui

2015-01-01

Although silicon nanoparticles dispersed in liquids are used in various applications ranging from bio-labeling to hydrogen production, their reactivities with their solvents and their catalytic properties re-main still unexplored. Here, we discovered that, because of their surface structures and mechanical strain, silicon nanoparticles react strongly with their solvents and may act as catalysts for the dehydrogenation, at room temperature, of secondary alcohols (e.g. isopropanol) to ketones and hydrogen. This catalytic reaction was followed by gas chromatography, pH measurements, mass spectroscopy and solidstate NMR. This discovery provides new understanding of the role played by silicon nanoparticles, and nanosilicon in general, in their stability in solvents in general as well as being candidates in catalysis.

Room Temperature Reactivity Of Silicon Nanocrystals With Solvents: The Case Of Ketone And Hydrogen Production From Secondary Alcohols: Catalysis?

KAUST Repository

El Demellawi, Jehad K.

2015-05-29

Although silicon nanoparticles dispersed in liquids are used in various applications ranging from bio-labeling to hydrogen production, their reactivities with their solvents and their catalytic properties re-main still unexplored. Here, we discovered that, because of their surface structures and mechanical strain, silicon nanoparticles react strongly with their solvents and may act as catalysts for the dehydrogenation, at room temperature, of secondary alcohols (e.g. isopropanol) to ketones and hydrogen. This catalytic reaction was followed by gas chromatography, pH measurements, mass spectroscopy and solidstate NMR. This discovery provides new understanding of the role played by silicon nanoparticles, and nanosilicon in general, in their stability in solvents in general as well as being candidates in catalysis.

Quantification of four major metabolites of embryotoxic N-methyl- and N-ethyl-2-pyrrolidone in human urine by cooled-injection gas chromatography and isotope dilution mass spectrometry.

Science.gov (United States)

Schindler, Birgit K; Koslitz, Stephan; Meier, Swetlana; Belov, Vladimir N; Koch, Holger M; Weiss, Tobias; Brüning, Thomas; Käfferlein, Heiko U

2012-04-17

N-Methyl- and N-ethyl-2-pyrollidone (NMP and NEP) are frequently used industrial solvents and were shown to be embryotoxic in animal experiments. We developed a sensitive, specific, and robust analytical method based on cooled-injection (CIS) gas chromatography and isotope dilution mass spectrometry to analyze 5-hydroxy-N-ethyl-2-pyrrolidone (5-HNEP) and 2-hydroxy-N-ethylsuccinimide (2-HESI), two newly identified presumed metabolites of NEP, and their corresponding methyl counterparts (5-HNMP, 2-HMSI) in human urine. The urine was spiked with deuterium-labeled analogues of these metabolites. The analytes were separated from urinary matrix by solid-phase extraction and silylated prior to quantification. Validation of this method was carried out by using both, spiked pooled urine samples and urine samples from 56 individuals of the general population with no known occupational exposure to NMP and NEP. Interday and intraday imprecision was better than 8% for all metabolites, while the limits of detection were between 5 and 20 μg/L depending on the analyte. The high sensitivity of the method enables us to quantify NMP and NEP metabolites at current environmental exposures by human biomonitoring.

Protection efficacy of gloves against components of the solvent in a sprayed isocyanate coating utilizing a reciprocating permeation panel.

Science.gov (United States)

Ceballos, Diana M; Reeb-Whitaker, Carolyn; Sasakura, Miyoko; Dills, Russell; Yost, Michael G

2015-04-01

Determine protection effectiveness of 5-mil natural rubber latex (0.13-mm), 5-mil nitrile rubber (0.13-mm), and 13-mil butyl rubber (0.33-mm) glove materials against solvents present in a commonly used automotive clear coat formulation using a novel permeation panel. The latex and nitrile gloves were the type commonly used by local autobody spray painters. Glove materials were tested by spraying an automotive clear coat onto an automated reciprocating permeation panel (permeation panel II). Temperature, relative humidity, and spray conditions were controlled to optimize clear coat loading homogeneity as evaluated by gravimetric analysis. Solvent permeation was measured using charcoal cloth analyzed by the National Institute for Occupational Safety and Health 1501 method. Natural rubber latex allowed 3-5 times the permeation of solvents relative to nitrile rubber for all 10 solvents evaluated: ethyl benzene, 2-heptanone, 1-methoxy-2-propyl acetate, o-xylene, m-xylene, p-xylene, n-butyl acetate, methyl isobutyl ketone, petroleum distillates, and toluene. There is a distinct behavior in solvent permeation before and after the coating dry time. Solvent permeation increased steadily before coating dry time and remained fairly constant after coating dry time. Butyl was not permeated by any of the solvents under the conditions tested. Commonly used 5-mil thick (0.13-mm) latex and nitrile gloves were ineffective barriers to solvents found in a commonly used clear coat formulation. Conversely, 13-mil (0.33-mm) butyl gloves were found to be protective against all solvents in the clear coat formulation. © The Author 2014. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Preparation of N(1-ethyl-2-pyrrolidyl-methyl)2-methoxy-4-iodo-125I-5-ethyl sulfonyl benzamide: a radioligand for the radioimmunoassay of sulpiride-related compounds

International Nuclear Information System (INIS)

Cardoso, M.T.; Pradelles, P.

1982-01-01

The preparation of 125 I labelling with a higher specific radioactivity of N(1-ethyl-2-pyrrolidyl-methyl)2-methoxy-5-ethyl sulfonyl benzamide, a potent biological analogue for sulpiride is described. The incorporation of iodine in the molecule was achieved by the substitution of aromatic amino groups via the diazo compound. Binding and immunological parameters of iodinated and tritiated tracers were compared. (author)

Comprehensive Biological Monitoring to Assess Isocyanates and Solvents Exposure in the NSW Australia Motor Vehicle Repair Industry.

Science.gov (United States)

Hu, Jimmy; Cantrell, Phillip; Nand, Aklesh

2017-10-01

Urethane products that contain isocyanates are extensively used in the motor vehicle repair (MVR) industry and other industries such as furniture and cabinet-making as two-pack spray paints, clears, and adhesives. Attention has recently been refocussed on isocyanate-containing chemicals, particularly in paints. The spray painters in the MVR industry had a propensity to develop industrial asthma at a rate 80 times higher than the general public, which was previously reported in the UK. To track workers exposure to isocyanates, urine samples were collected from 196 spray painters who worked mainly in 78 MVR shops across 54 New South Wales (NSW) towns and suburbs. The biological monitoring also covered exposure testing to a wide variety of solvents including aromatic hydrocarbons, ketones, and alcohols. The main finding of the study was that 2.6% of the spray painters surveyed in the MVR industry in NSW that handled isocyanate-containing paints showed exposure to isocyanates; with 1.0% being moderately exposed, which is more than twice the current UK's Health and Safety Executive (HSE) Biological Monitoring Guidance Value (BMGV) of 1 µmol mol-1 creatinine. Potential exposures to toluene (a solvent often found in paint thinners) was monitored via hippuric acid (HA) urine levels and showed 2.6% of the spray painters surveyed to be over the US' American Conference of Government Industrial Hygienists (ACGIH) Biological Exposure Index (BEI) of 1010 mmol/mole creatinine for HA. The other solvents or their metabolites were all below their respective BEI; these comprised benzene, xylene, ethyl benzene, methyl ethyl ketone, acetone, methanol, and ethanol. These findings indicate that isocyanates and certain solvents exposure were occurring in the NSW Australia vehicle repair industry, albeit at lower levels than previous occupational biological monitoring studies that showed higher exposure levels, particularly for isocyanates. One reason for this could be the increasing use

Ethylic or methylic route to soybean biodiesel? Tracking environmental answers through life cycle assessment

International Nuclear Information System (INIS)

Alejos Altamirano, Carlos Alberto; Yokoyama, Lídia; Medeiros, José Luiz de; Queiroz Fernandes Araújo, Ofélia de

2016-01-01

Highlights: • Life cycle of biodiesel using alternative transesterification routes is analyzed. • Bioethanol can potentially decrease CO_2 emissions of methanol biodiesel. • Contrarily, equivalent CO_2 emissions are retained and renewability is reduced. • Water footprint increases from 37.12 (methanol) to 44.88 m"3/GJ biodiesel (ethanol). • Energy efficiency is reduced from 79.37% (methanol) to 75.19 (ethanol %). - Abstract: Biodiesel is a renewable fuel produced by transesterification of triacylglicerides (TAG) contained in vegetable oils and animal fats, to yield alkyl esters (biodiesel) and glycerin. Methanol is the main transesterification agent employed resulting in FAME (fatty acid methyl esters), which is primarily obtained from natural gas reforming (fossil source). Substitution of methanol by ethanol produces FAEE (fatty acid ethyl esters) and has the potential to render biodiesel a fully renewable fuel. Although renewability is a significant driving force for the proposed alcohol replacement, environmental performance of the alternative transesterification is questioned. The answer is herein sought through a comparative Life Cycle Assessment (LCA) of the two production chains. The study tracks CO_2 emissions, energy efficiency, water and resources consumption, and environmental impacts (Acidification Potential – AP, Global Warming Potential – GWP, Eutrophication Potential – EP, and Human Toxicity Potential – TP). The boundaries of the biodiesel production chains extend from the extraction of raw-materials to its final use as transportation fuel in buses, applied to the Brazilian scenario. Results show that substitution of the methylic route with the ethylic route does not attribute significant environmental benefits. Furthermore, the ethylic route presents competitive advantages only in the category of GWP, and exhibits inferior performance in the remaining evaluated impact categories. Finally, a greater consumption of water and energy

Evaluation and Characterization of Biodiesels Obtained Through Ethylic or Methylic Transesterification of Tryacylglicerides in Corn Oil

Directory of Open Access Journals (Sweden)

Douglas Queiroz Santos

2014-06-01

Full Text Available This work was devoted to the transesterification of corn oil either with methyl or ethyl alcohol and to the characterization of the biodiesels (composed by FAME—fatty acid methyl esters—or FAEE—fatty acid ethyl esters, respectively produced. As an initial hypothesis, it was argued whether or not the two alcohols, both with short molecular chains, would impart significant differences to the chemical characteristics of the two biodiesels from corn oil. The most common properties of the biodiesels were evaluated by determining corresponding parameters for acid value, peroxide value, water content, oxidative stability, free and total glycerin, kinematic viscosity at 40 ℃ and density at 20 ℃, for both chemical routes, FAME and FAEE. In general, values were found to be well within the recommended limits for commercial biodiesel, in accordance with the Brazilian, European and American standard recommendations, except only for the oxidative stability. The methyl biodiesel presented acidity of 0.08 mg KOH/g; peroxide index, 23.77 meq/kg; oxidation stability, 3.10 h; water content, 297.1 mg/kg; total glycerin, 0.092 %; free glycerin, 0.009 %; viscosity, 4.05 mm2/s and density, 878.7 kg/m. The methyl biodiesel presented acidity of 0.11 mg/ KOH; peroxide index, 22.39 meq/kg; oxidation stability, 2.13 h; water content, 264.8 mg/kg; total glycerin, 0.25 %; free glycerin, 0.02 %; viscosity, 4.37 mm2/s and density, 874.0 kg/m. From a direct inspection of chemical data for the two products prepared via the two chemical routes, it can be drawn that values of the physical and chemical parameters for both, methyl and ethyl biodiesels, are essentially similar, except for the oxidative stability. However, the oxidative stability can be suitably adjusted by adding an anti-oxidizing agent to the ethyl biodiesel medium. The two biodiesels are thus promising alternatives to fully replace or to be admixed to the mineral diesel. Relatively to the pure petrol

Searching for trans ethyl methyl ether in Orion KL.

Science.gov (United States)

Tercero, B; Cernicharo, J; López, A; Brouillet, N; Kolesniková, L; Motiyenko, R A; Margulès, L; Alonso, J L; Guillemin, J-C

2015-10-01

We report on the tentative detection of trans ethyl methyl ether (tEME), t-CH 3 CH 2 OCH 3 , through the identification of a large number of rotational lines from each one of the spin states of the molecule towards Orion KL. We also search for gauche-trans-n-propanol, Gt-n-CH 3 CH 2 CH 2 OH, an isomer of tEME in the same source. We have identified lines of both species in the IRAM 30 m line survey and in the ALMA Science Verification data. We have obtained ALMA maps to establish the spatial distribution of these species. Whereas tEME mainly arises from the compact ridge component of Orion, Gt-n-propanol appears at the emission peak of ethanol (south hot core). The derived column densities of these species at the location of their emission peaks are ≤(4.0 ± 0.8) × 10 15 cm -2 and ≤(1.0 ± 0.2)× 10 15 cm -2 for tEME and Gt-n-propanol, respectively. The rotational temperature is ~100 K for both molecules. We also provide maps of CH 3 OCOH, CH 3 CH 2 OCOH, CH 3 OCH 3 , CH 3 OH, and CH 3 CH 2 OH to compare the distribution of these organic saturated O-bearing species containing methyl and ethyl groups in this region. Abundance ratios of related species and upper limits to the abundances of non-detected ethers are provided. We derive an abundance ratio N (CH 3 OCH 3 )/ N (tEME) ≥ 150 in the compact ridge of Orion.

Remedial Investigation Badger Army Ammunition Plant, Baraboo, Wisconsin. Volume 1. Text Sections 1 Through 12

Science.gov (United States)

1993-04-01

VOCs (acetone [ACET], trichlorofluoromethane [CCL3F], methyl ethyl ketone [MEK]) sporadically detected at very low concentrations (< 1 parts per billion...associated with the site includes red pine ( Pinus resinosa), hickories, cedar (Thuja occidentalis), and American elm (Ulmus americana). Grasses and weedy...cd)pyrene ICDPYR iron FE lead PB magnesium MG *manganese MN mercury HG methylene chloride CH12CL2 methyl ethyl ketone or 2-butanone MIEK

Effects on wildlife of ethyl and methyl parathion applied to California rice fields

Science.gov (United States)

Custer, T.W.; Hill, E.F.; Ohlendorf, H.M.

1985-01-01

Selected rice fields on the Sacramento National Wildlife Refuge Complex were aerially sprayed one time during May or June 1982 with either ethyl (0.11 kg Al/ha) or methyl (0.84 kg AI/ha) parathion for control of tadpole shrimp, Triops longicaudatus. No sick or dead vertebrate wildlife were found or adjacent to the treated rice fields after spraying. Specimens of the following birds and mammals were assayed for brain cholinesterase (ChE) activity to determine exposure to either form of parathion; house mouse, Mus musculus; black-tailed jackrabbit, Lepus californicus; mallard, Anas platyrhynchos; ring-necked pheasant, Phasianus colchicus; American coot, Fulica americana; and red-winged blackbird, Agelaius phoeniceus. Both mice and pheasants from methyl parathion-treated fields had overall mean ChE activities that were significantly (P < 0.05) inhibited compared with controls, and 7, 40, 54 and 57% of individual blackbirds, pheasant, mice, and coots, respectively, had inhibited brain ChE activities (i.e., less than -2 SD of control mean). Although no overall species effect was detected for ethyl parathoid treatment, pheasants (43%), coots (33%), and mice (37%) had significantly inhibited brain ChE activities. Neither of the parathion treatment appeared acutely hazardous to wildlife in or adjacent to rice fields, but sufficient information on potential hazards was obtained to warrant caution in use of these chemicals, especially methyl parathion, in rice fields.

Solvent extraction of Zn and metals in Zn ores by nonphosphorous solvents

International Nuclear Information System (INIS)

Auchapt, J.M.; Tostain, Jacqueline.

1975-07-01

This bibliography follows a first work on Zn solvent extraction by organo-phosphorous compounds. The other solvents used in Zn extraction, are studied: oxygenated nonphosphorous solvents (ketones, alcohols, carboxylic acids, sulfonates), nitrogenous solvents and hydrocarbons [fr

Solvent induced supramolecular anisotropy in molecular gels

Energy Technology Data Exchange (ETDEWEB)

Rogers, Michael A., E-mail: mroger09@uoguelph.ca [Department of Food Science, University of Guelph, Guelph, Ontario, N3C3X9 (Canada); Corradini, Maria G. [Department of Food Science, University of Massachusetts Amherst, Amherst, MA, 01003 (United States); Emge, Thomas [Department of Chemistry and Biochemistry, Rutgers University, New Brunswick, NJ, 08901 (United States)

2017-06-15

Herein is the first report of solvent induced anisotropy in 12-hydroxystearic acid self-assembled fibrillar networks. Increasing the chain length of polar solvent, such as nitriles and ketones, tailored the anisotropy of the fibrillar aggregates. 12HSA molecular gels, comprised of alkanes, exhibited an isotropic fibrillar network irrespective of the alkane chain length. In polar solvents, anisotropy, observed using 2D powder x-ray diffraction profiles, is correlated to a fibrillar supramolecular morphologies in long chain nitriles and ketones while sphereulitic crystals are correlated to x-ray diffraction patterns with an isotropic scatter intensity in short chain ketones and nitriles. These changes directly modify the final physical properties of the gels. - Highlights: • 12-HSA self-assembles into crystalline supramolecular morphologies depending on the solvent. • Alkanes, short chain nitriles and ketones led to 12-HSA displaying supramolecular isotropy. • In long chain nitriles and ketones, 12-HSA displays supramolecular anisotropy.

Solvent induced supramolecular anisotropy in molecular gels

International Nuclear Information System (INIS)

Rogers, Michael A.; Corradini, Maria G.; Emge, Thomas

2017-01-01

Herein is the first report of solvent induced anisotropy in 12-hydroxystearic acid self-assembled fibrillar networks. Increasing the chain length of polar solvent, such as nitriles and ketones, tailored the anisotropy of the fibrillar aggregates. 12HSA molecular gels, comprised of alkanes, exhibited an isotropic fibrillar network irrespective of the alkane chain length. In polar solvents, anisotropy, observed using 2D powder x-ray diffraction profiles, is correlated to a fibrillar supramolecular morphologies in long chain nitriles and ketones while sphereulitic crystals are correlated to x-ray diffraction patterns with an isotropic scatter intensity in short chain ketones and nitriles. These changes directly modify the final physical properties of the gels. - Highlights: • 12-HSA self-assembles into crystalline supramolecular morphologies depending on the solvent. • Alkanes, short chain nitriles and ketones led to 12-HSA displaying supramolecular isotropy. • In long chain nitriles and ketones, 12-HSA displays supramolecular anisotropy.

Sulphur and oxygen sequestration of n-C{sub 37} and n-C{sub 38} unsaturated ketones in an immature kerogen and the release of their carbon skeletons during early stages of thermal maturation

Energy Technology Data Exchange (ETDEWEB)

Koopmans, M.P.; De Leeuw, J.W.; Damste, J.S.S. [Netherlands Institute for Sea Research (NIOZ), Den Burg (Netherlands)] [and others

1997-06-01

Sedimentary rock from the Gessoso-solfifera Formation (Messinian) in the Vena del Gesso Basin (northern Italy) containing immature (R{sub o} = 0.25%) S-rich organic matter was artificially matured by hydrous pyrolysis at temperatures from 160 to 330{degrees}C for 72 h to study the diagenetic fate of n-C{sub 37} and n-C{sub 38} di- and tri-unsaturated methyl and ethyl ketones (alkenones) biosynthesised by several prymnesiophyte algae. During early diagenesis, the alkenones are incorporated into the kerogen by both sulphur and oxygen cross-linking as indicated by chemical degradation experiments with the kerogen of the unheated sample. Heating at temperatures between 160 and 260{degrees}C, which still represents early stages of thermal maturation, produces large amounts (up to 1 mg/g TOC) of S-bound, O-bound, and both S- and O-bound n-C{sub 37} and n-C{sub 38} skeletons, saturated n-C{sub 37} and n-C{sub 38} methyl, ethyl, and mid-chain ketones, C{sub 37} and C{sub 38} mid-chain 2,5-di-n-alkylthiophenes, C{sub 37} and C{sub 38} 1,2-di-n-alkylbenzenes, and C{sub 37} and C{sub 38} n-alkanes. With increasing thermal maturation, three forms of the n-C{sub 37} and n-C{sub 38} skeletons are relatively stable (saturated hydrocarbons, 1,2-di-n-alkylbenzenes and saturated ketones), whereas the S- and O-bound skeletons are relatively labile. These results suggest that in natural situations saturated ketones with an n-C{sub 37} and n-C{sub 38} skeleton can be expected as well as the corresponding hydrocarbons. 58 refs., 8 figs., 2 tabs.

Densities and Kinematic Viscosities for the Systems Benzene + Methyl Formate, Benzene + Ethyl Formate, Benzene + Propyl Formate, and Benzene + Butyl Formate

DEFF Research Database (Denmark)

Emmerling, Uwe; Rasmussen, Peter

1998-01-01

a Redlich-Kister type of expression with temperature-independent parameters and the data for the systems benzene + ethyl formate, benzene + propyl formate, and benzene + butyl formate with temperature-dependent parameters. The viscosities have furthermore been compared to values predicted by means of the GC......Densities and kinematic viscosities have been measured for the system benzene + methyl formate at 20°C and for the systems benzene + ethyl formate, benzene + propyl formate, and benzene + butyl formate from 20°C to 50°C. The results for the system benzene + methyl formate have been correlated using...

Synthesis of (R,S)-[2,3-{sup 13}C{sub 2}]-1-(1`-methyl-2`-pyrrolidinyl)propan-2-one; {l_brace}(R,S)-[2`,3`-{sup 13}C{sub 2}]hygrinePound right bracePound

Energy Technology Data Exchange (ETDEWEB)

Abraham, T.W.; Leete, Edward [Minnesota Univ., Minneapolis, MN (United States). Dept. of Chemistry

1996-05-01

2-Ethoxy-1-methyl-5-pyrrolidinone (1) was reacted with ethyl [3,4-{sup 13}C{sub 2}]-acetoacetate (2) in the presence of TiCl{sub 4} to give ethyl [3,4-{sup 13}C{sub 2}]-2-(1`-methyl-5`-oxo-2`-pyrrolidinyl)-3-oxobutanoate (3) in 85% yield. Decarboethoxylation of ethyl [3,4-{sup 13}C{sub 2}]-2-(1`-methyl-5`-oxo-2`-pyrrolidinyl)-3-oxobutan-oate (3) was accomplished using NaCl and H{sub 2}O in DMSO to give (R,S)-[2,3-{sup 13}C{sub 2}]-1-(1`-methyl-5`-oxo-2`-pyrrolidinyl)propan-2-o ne (4) in 91% yield. Protection of the ketone as a ketal (ethylene glycol, H{sup +}), followed by reduction of the amide to the amine using LiAlH{sub 4} and subsequent deprotection of the ketal gave (R,S)-[2,3-{sup 13}C{sub 2}]-1-(1`-methyl-2`-pyrrolidinyl)propan-2-one ((R,s)-[2`, 3`-{sup 13}C{sub 2}]Hygrine) (8) in 78% yield. (61% overall yield from ethyl [3,4-{sup 13}C{sub 2}]acetoacetate). (Author).

Investigation of ethyl lactate as a green solvent for desorption of total petroleum hydrocarbons (TPH) from contaminated soil.

Science.gov (United States)

Jalilian Ahmadkalaei, Seyedeh Pegah; Gan, Suyin; Ng, Hoon Kiat; Abdul Talib, Suhaimi

2016-11-01

Treatment of oil-contaminated soil is a major environmental concern worldwide. The aim of this study is to examine the applicability of a green solvent, ethyl lactate (EL), in desorption of diesel aliphatic fraction within total petroleum hydrocarbons (TPH) in contaminated soil and to determine the associated desorption kinetics. Batch desorption experiments were carried out on artificially contaminated soil at different EL solvent percentages (%). In analysing the diesel range of TPH, TPH was divided into three fractions and the effect of solvent extraction on each fraction was examined. The experimental results demonstrated that EL has a high and fast desorbing power. Pseudo-second order rate equation described the experimental desorption kinetics data well with correlation coefficient values, R 2 , between 0.9219 and 0.9999. The effects of EL percentage, initial contamination level of soil and liquid to solid ratio (L/S (v/w)) on initial desorption rate have also been evaluated. The effective desorption performance of ethyl lactate shows its potential as a removal agent for remediation of TPH-contaminated soil worldwide.

Performance of low pH biofilters treating a paint solvent mixture: Continuous and intermittent loading

International Nuclear Information System (INIS)

Qi Bing; Moe, William M.

2006-01-01

Two biofilters packed with a reticulated polyurethane foam medium were inoculated with a compost-derived enrichment culture grown under acidic conditions (pH 3.0) and then operated over a period lasting 63 days. Both biofilters were supplied with a humidified gas stream containing a five-component mixture of acetone, methyl ethyl ketone, toluene, ethylbenzene, and p-xylene at a total VOC loading rate 80.3 g m -3 h -1 to simulate treatment of air emissions resulting from manufacture of reformulated paint. One biofilter was operated under continuous loading conditions and the other received intermittent loading with contaminants supplied only 8 h/day. Nutrient solution with pH 3.0 was supplied approximately once per week to provide nitrogen and other nutrients. Data are presented which demonstrate that undefined mixed cultures acclimated at low pH can successfully treat paint solvent mixtures in biofilters. The biofilter receiving continuous loading reached high overall removal efficiency (greater than 90% overall removal) 3 weeks after startup, and performance increased over time reaching overall removal in the range of 97-99% after 50 days. Performance of the intermittently loaded biofilter developed more slowly, requiring 6 weeks to stabilize at an overall removal efficiency in excess of 90%. In both biofilters, ketone components were more rapidly degraded than aromatic components, and removal of aromatic compounds was somewhat unstable even after 2 months of biofilter operation. Scanning electron microscopy (SEM) revealed that fungi dominated the microbial populations in both biofilters

Alkylation of deoxyribonucleic acid by carcinogens dimethyl sulphate, ethyl methanesulphonate, N-ethyl-N-nitrosourea and N-methyl-N-nitrosourea. Relative reactivity of the phosphodiester site thymidylyl(3'-5')thymidine.

Science.gov (United States)

Swenson, D H; Lawley, P D

1978-01-01

1. The ethyl phosphotriester of thymidylyl(3'-5')thymidine, dTp(Et)dT, was identified as a product from reaction of DNA with N-ethyl-N-nitrosourea, by procedures parallel to those reported previously for the methyl homologue produced by N-methyl-N-nitrosourea. 2. Enzymic degradation to yield alkyl phosphotriesters from DNA alkylated by these carcinogens and by dimethyl sulphate and ethyl methanesulphonate was studied quantitatively, and the relative yields of the triesters dTp(Alk)dT were determined. The relative reactivity of the phosphodiester group dTpdT to each of the four carcinogens was thus obtained, and compared with that of DNA overall, or with that of the N-7 atom of guanine in DNA. Relative reactivity of the phosphodiester group was lowest towards dimethyl sulphate, the least electrophilic of the reagents used, and was highest towards N-ethyl-N-nitrosourea, the most electrophilic reagent. 3. The nature of the alkyl group transferred also influenced reactivity of the phosphodiester site, since this site was relatively more reactive towards ethylation than would be predicted simply from the known Swain-Scott s values of the alkylating agents. It was therefore suggested that the steric accessibility of the weakly nucleophilic phosphodiester group on the outside of the DNA macromolecule favours its reaction with ethylating, as opposed to methylating, reagents. 4. Taking a value of the Swain-Scott nucleophilicity (n) of 2.5 for an average DNA nucleotide unit [Walles & Ehrenberg (1969) Acta Chem. Scand. 23, 1080-1084], a value of n of about 1 for the phosphodiester group was deduced, and this value was found to be 2-3 units less than that for the N-7 atom of guanine in DNA. 5. The reactivity of DNA overall was markedly high towards the alkylnitrosoureas, despite their relatively low s values. This was ascribed to an electrostatic factor that favoured reaction of the negatively charged polymer with alkyldiazonium cation intermediates. PMID:208508

Effects of wildlife of ethyl and methyl parathion applied to California USA rice fields

Science.gov (United States)

Custer, T.W.; Hill, E.F.; Ohlendorf, H.M.

1985-01-01

Selected rice fields on the Sacramento National Wildlife Refuge Complex were aerially sprayed one time during May or June 1982 with either ethyl (0.11 kg Al/ha) or methyl (0.84 kg AI/ha) parathion for control of tadpole shrimp, Triops longicaudatus. No sick or dead vertebrate wildlife were found or adjacent to the treated rice fields after spraying. Specimens of the following birds and mammals were assayed for brain cholinesterase (ChE) activity to determine exposure to either form of parathion; house mouse, Mus musculus; black-tailed jackrabbit, Lepus californicus; mallard, Anas platyrhynchos; ring-necked pheasant, Phasianus colchicus; American coot, Fulica americana; and red-winged blackbird, Agelaius phoeniceus. Both mice and pheasants from methyl parathion-treated fields had overall mean ChE activities that were significantly (P < 0.05) inhibited compared with controls, and 7, 40, 54 and 57% of individual blackbirds, pheasant, mice, and coots, respectively, had inhibited brain ChE activities (i.e., less than -2 SD of control mean). Although no overall species effect was detected for ethyl parathoid treatment, pheasants (43%), coots (33%), and mice (37%) had significantly inhibited brain ChE activities. Neither of the parathion treatment appeared acutely hazardous to wildlife in or adjacent to rice fields, but sufficient information on potential hazards was obtained to warrant caution in use of these chemicals, especially methyl parathion, in rice fields.

Density, viscosity, isothermal (vapour + liquid) equilibrium, excess molar volume, viscosity deviation, and their correlations for chloroform + methyl isobutyl ketone binary system

International Nuclear Information System (INIS)

Clara, Rene A.; Gomez Marigliano, Ana C.; Solimo, Horacio N.

2007-01-01

Density and viscosity measurements for pure chloroform and methyl isobutyl ketone at T = (283.15, 293.15, 303.15, and 313.15) K as well as for the binary system {x 1 chloroform + (1 - x 1 ) methyl isobutyl ketone} at the same temperatures were made over the whole concentration range. The experimental results were fitted to empirical equations, which permit the calculation of these properties over the whole concentration and temperature ranges studied. Data of the binary mixture were further used to calculate the excess molar volume and viscosity deviation. The (vapour + liquid) equilibrium (VLE) at T = 303.15 K for this binary system was also measured in order to calculate the activity coefficients and the excess molar Gibbs energy. This binary system shows no azeotrope and negative deviations from ideal behaviour. The excess or deviation properties were fitted to the Redlich-Kister polynomial relation to obtain their coefficients and standard deviations

Kinetics and thermodynamics of oxidation mediated reaction in L-cysteine and its methyl and ethyl esters in dimethyl sulfoxide-d6 by NMR spectroscopy

Science.gov (United States)

Dougherty, Ryan J.; Singh, Jaideep; Krishnan, V. V.

2017-03-01

L-Cysteine (L-Cys), L-Cysteine methyl ester (L-CysME) or L-Cysteine ethyl ester (L-CysEE), when dissolved in dimethyl sulfoxide, undergoes an oxidation process. This process is slow enough and leads to nuclear magnetic resonance (NMR) spectral changes that could be monitored in real time. The oxidation mediated transition is modeled as a pseudo-first order kinetics and the thermodynamic parameters are estimated using the Eyring's formulation. L-Cysteine and their esters are often used as biological models due to the remarkable thiol group that can be found in different oxidation states. This oxidation mediated transition is due to the combination of thiol oxidation to a disulfide followed by solvent-induced effects may be relevant in designing cysteine-based molecular models.

Ultrasound aided in situ transesterification of crude palm oil adsorbed on spent bleaching clay

International Nuclear Information System (INIS)

Boey, Peng-Lim; Ganesan, Shangeetha; Maniam, Gaanty Pragas; Ali, Dafaalla Mohamed Hag

2011-01-01

Research highlights: → Crude palm oil adsorbed on spent bleaching clay converted to biodiesel. → Ultrasound dislodges adsorbed oil from spent bleaching clay into reaction mixture. → Co-solvents promotes miscibility of the reactants. -- Abstract: Adsorbed crude palm oil on spent bleaching clay (SBC) was in situ transesterified to methyl esters (biodiesel) by the aid of ultrasound and organic co-solvents (petroleum ether (PE) or ethyl methyl ketone (EMK)). The SBC under study was found to contain 24.2-27.0% of crude oil with free fatty acids (FFA) of 3.01% and moisture content of 0.29%. The optimized reaction conditions were as follows: methanol to oil molar ratio of 150:1; catalyst (KOH), 20%; reaction temperature, 60 ± 2 o C; reaction time, 2 h. Using PE as a co-solvent, highest conversion of 75.2% was achieved while 60% was recorded with EMK.

Environmental effect of rapeseed oil ethyl ester

International Nuclear Information System (INIS)

Makareviciene, V.; Janulis, P.

2003-01-01

Exhaust emission tests were conducted on rapeseed oil methyl ester (RME), rapeseed oil ethyl ester (REE) and fossil diesel fuel as well as on their mixtures. Results showed that when considering emissions of nitrogen oxides (NO x ), carbon monoxide (CO) and smoke density, rapeseed oil ethyl ester had less negative effect on the environment in comparison with that of rapeseed oil methyl ester. When fuelled with rapeseed oil ethyl ester, the emissions of NO x showed an increase of 8.3% over those of fossil diesel fuel. When operated on 25-50% bio-ester mixed with fossil diesel fuel, NO x emissions marginally decreased. When fuelled with pure rapeseed oil ethyl ester, HC emissions decreased by 53%, CO emissions by 7.2% and smoke density 72.6% when compared with emissions when fossil diesel fuel was used. Carbon dioxide (CO 2 ) emissions, which cause greenhouse effect, decreased by 782.87 g/kWh when rapeseed oil ethyl ester was used and by 782.26 g/kWh when rapeseed oil methyl ester was used instead of fossil diesel fuel. Rapeseed oil ethyl ester was more rapidly biodegradable in aqua environment when compared with rapeseed oil methyl ester and especially with fossil diesel fuel. During a standard 21 day period, 97.7% of rapeseed oil methyl ester, 98% of rapeseed oil ethyl ester and only 61.3% of fossil diesel fuel were biologically decomposed. (author)

Stainless Steel Corrosion Studies Final Report: FY17 End of-Year

Energy Technology Data Exchange (ETDEWEB)

Kelly, Daniel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Milenski, Helen Marie [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinez, Destiny [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-09-08

Two materials are being considered in applications requiring their contact against stainless steel surfaces. These materials include the solvent methyl ethyl ketone (MEK), and the polymer neoprene (polychloroprene). There is concern that contact of these materials with stainless steel substrates may lead to corrosion. To address these concerns we have undertaken corrosion studies under conditions expected to be more aggressive than in intended applications. These conditions include elevated temperature and humidity, and submersion and suspension in solvent vapors, in an attempt to accelerate any potential deleterious interactions. Corrosion rates below 0.1 mpy have historically been deemed INSIGNIFICANT from a WR Production standpoint; corresponding guidelines for non-production applications are lacking.

Effects of Composition and Structure of Mg/Al Oxides on Their Activity and Selectivity for the Condensation of Methyl Ketones

KAUST Repository

Shylesh, Sankaranarayanapillai

2016-09-22

The effects of chemical composition and pretreatment on Mg–Al hydrotalcites and alumina-supported MgO were evaluated for the gas-phase, self-condensation reaction of C3–C5 biomass-derived methyl ketones. We show that the selectivity toward the acyclic dimer enone and the cyclic enone trimer can be tuned by controlling the temperature of hydrotalcite calcination. Methyl ketone cyclization is promoted by Lewis acidic sites present on the hydrotalcite catalysts. XRD and thermal decomposition analysis reveal that the formation of periclase MgO starts above 623 K accompanied by complete disappearance of the hydrotalcite structure and is accompanied by an increase in hydroxyl condensation as the formation of well-crystallized periclase. 27Al MQMAS and 25Mg MAS NMR show that at progressively higher temperatures, Al3+ cations diffuses out of the octahedral brucite layers and incorporate into the tetrahedral and octahedral sites of the MgO matrix thereby creating defects to compensate the excess positive charge generated. The oxygen anions adjacent to the Mg2+/Al3+ defects become coordinatively unsaturated, leading to the formation of new basic sites. A kinetic isotope effect, kH/kD = 0.96, is observed at 473 K for the reaction of (CH3)2CO versus (CD3)2CO, which suggests that carbon–carbon bond formation leading to the dimer aldol product is the rate-determining step in the condensation reaction of methyl ketones. We also show that acid–base catalysts having similar reactivity and higher hydrothermal stability to that of calcined hydrotalcites can be achieved by creating defects in MgO crystallites supported alumina as a consequence of the diffusion of Al3+ cations into MgO. The physical properties of these materials are shown to be very similar to those of hydrotalcite calcined at 823 K.

Effects of Composition and Structure of Mg/Al Oxides on Their Activity and Selectivity for the Condensation of Methyl Ketones

KAUST Repository

Shylesh, Sankaranarayanapillai; Kim, Daeyoup; Gokhale, Amit A.; Canlas, Christian; Struppe, Jochem O.; Ho, Christopher R.; Jadhav, Deepak; Yeh, Alice; Bell, Alexis T.

2016-01-01

The effects of chemical composition and pretreatment on Mg–Al hydrotalcites and alumina-supported MgO were evaluated for the gas-phase, self-condensation reaction of C3–C5 biomass-derived methyl ketones. We show that the selectivity toward the acyclic dimer enone and the cyclic enone trimer can be tuned by controlling the temperature of hydrotalcite calcination. Methyl ketone cyclization is promoted by Lewis acidic sites present on the hydrotalcite catalysts. XRD and thermal decomposition analysis reveal that the formation of periclase MgO starts above 623 K accompanied by complete disappearance of the hydrotalcite structure and is accompanied by an increase in hydroxyl condensation as the formation of well-crystallized periclase. 27Al MQMAS and 25Mg MAS NMR show that at progressively higher temperatures, Al3+ cations diffuses out of the octahedral brucite layers and incorporate into the tetrahedral and octahedral sites of the MgO matrix thereby creating defects to compensate the excess positive charge generated. The oxygen anions adjacent to the Mg2+/Al3+ defects become coordinatively unsaturated, leading to the formation of new basic sites. A kinetic isotope effect, kH/kD = 0.96, is observed at 473 K for the reaction of (CH3)2CO versus (CD3)2CO, which suggests that carbon–carbon bond formation leading to the dimer aldol product is the rate-determining step in the condensation reaction of methyl ketones. We also show that acid–base catalysts having similar reactivity and higher hydrothermal stability to that of calcined hydrotalcites can be achieved by creating defects in MgO crystallites supported alumina as a consequence of the diffusion of Al3+ cations into MgO. The physical properties of these materials are shown to be very similar to those of hydrotalcite calcined at 823 K.

Silica sulfuric acid and as an efficient catalyst for the Friedlander quinoline synthesis from simple ketones and ortho - amino aryl ketones under microwave irradiation

International Nuclear Information System (INIS)

Zolfigol, M. A.; Salehi, P.; Shiri, M.; Faal Rastegar, T.; Ghaderi, A.

2008-01-01

The synthesis of quinoline derivatives via Friedlander method from ortho-amino aryl ketones in the presence of a catalytic amount of silica sulfuric acid under solvent-free condition and microwave irradiation was described. A good range of simple ketones such as cyclohexanone and deoxybenzoin were used

Thermotolerant cyclamen with reduced acrolein and methyl vinyl ketone.

Science.gov (United States)

Kai, Hiroomi; Hirashima, Keita; Matsuda, Osamu; Ikegami, Hidetoshi; Winkelmann, Traud; Nakahara, Takao; Iba, Koh

2012-06-01

Reduced levels of trienoic fatty acids (TAs) in chloroplast membranes induce thermotolerance in several plant species, but the underlying mechanisms remain unclear. TA peroxidation in plant cell membranes generates cytotoxic, TA-derived compounds containing α,β-unsaturated carbonyl groups. The relationship between low TA levels and the amounts of cytotoxic TA-derived compounds was examined using thermotolerant transgenic cyclamen (Cyclamen persicum Mill.) with low TA contents. Changes in the levels of the cytotoxic TA-derived acrolein (ACR), methyl vinyl ketone (MVK), (E)-2-hexenal, 4-hydroxy-2-nonenal, and malondialdehyde were analysed in the leaf tissues of wild-type (WT) and thermotolerant transgenic cyclamen under heat stress. Levels of ACR and MVK in the WT increased in parallel with the occurrence of heat-induced tissue damage, whereas no such changes were observed in the thermotolerant transgenic lines. Furthermore, exogenous ACR and MVK infiltrated into leaves to concentrations similar to those observed in heat-stressed WT leaves caused similar disease symptoms. These results suggest that thermotolerance in transgenic cyclamen depends on reduced production rates of ACR and MVK under heat stress, due to the low level of TAs in these plants.

STABILITY OF EMULSIFIER-FREE EMULSION COPOLYMERIZATION OF METHYL METHACRYLATE/ BUTYL ACRYLATE/SODIUM MONO(ETHYL POLYOXYETHYLENE) MALEATE

Institute of Scientific and Technical Information of China (English)

Mao-gen Zhang; Zhi-xue Weng; Zhi-ming Huang; Zu-ren Pan

1999-01-01

A series of new water-soluble bifunctional comonomers having both carboxyl and alkyl polyoxyethylene groups, such as sodium mono(ethyl polyoxyethylene) maleate (ZE series) with various molecular weights of polyoxyethylene ethyl ether, were synthesized and characterized. The effects of the structural factor, the amount and feeding mode of the comonomers, the initiator concentration and polymerization temperature on the stability of emulsifier-free emulsion copolymerization of methyl methacrylate (MMA) and butyl acrylate (BA) in the presence of a small amount of ZE with potassium persulfate as initiator were investigated. Stable, almost monodispersed MMA/BA/ZE emulsifier-free latex particles were prepared.

Extraction of basil leaves (ocimum canum) oleoresin with ethyl acetate solvent by using soxhletation method

Science.gov (United States)

Tambun, R.; Purba, R. R. H.; Ginting, H. K.

2017-09-01

The goal of this research is to produce oleoresin from basil leaves (Ocimum canum) by using soxhletation method and ethyl acetate as solvent. Basil commonly used in culinary as fresh vegetables. Basil contains essential oils and oleoresin that are used as flavouring agent in food, in cosmetic and ingredient in traditional medicine. The extraction method commonly used to obtain oleoresin is maceration. The problem of this method is many solvents necessary and need time to extract the raw material. To resolve the problem and to produce more oleoresin, we use soxhletation method with a combination of extraction time and ratio from the material with a solvent. The analysis consists of yield, density, refractive index, and essential oil content. The best treatment of basil leaves oleoresin extraction is at ratio of material and solvent 1:6 (w / v) for 6 hours extraction time. In this condition, the yield of basil oleoresin is 20.152%, 0.9688 g/cm3 of density, 1.502 of refractive index, 15.77% of essential oil content, and the colour of oleoresin product is dark-green.

Study on the use of solid electrodes for potentiometric titrations in non-aqueous solvents-I

International Nuclear Information System (INIS)

Fatibello Filho, O.; Carvalho, W.M. de; Capelato, M.D.; Bulhoes, L.O.S.; Almeida Neves, E.F. de

1984-01-01

Fatty acids and ethanolamines were titrated potentiometrically with tetrabutylammnonium hydroxide in methyl isobutyl ketone-isopropyl alcohol and with perchloric acid in ethanol, respectively. A study of utilization of Sb, Sn, W, PbO 2 , Ti and 316L stainless steel oxides - Ag/AgBr/Bu 4 NBr (x M)/solvent electrode systems have been investigated in comparison with the glass - Ag/AgBr/Bu 4 NBr (x M)/solvent system. The best performance was obtained using W, Sb, PbO 2 and Ti electrodes have yielded a larger potential shift than glass electrode for acid-base titration. (C.L.B.) [pt

A comparative study of the chemical kinetics of methyl and ethyl propanoate

KAUST Repository

Farooq, Aamir

2014-10-01

High temperature pyrolysis of methyl propanoate (CH3CH 2C(O)OCH3) and ethyl propanoate (CH3CH 2C(O)OCH2CH3) was studied behind reflected shock waves at temperatures of 1250-1750 K and pressure of 1.5 atm. Species time-histories were recorded for CO, CO2, C2H4, and H2O using laser absorption methods over a test time of 1 ms. Pyrolysis of methyl propanoate (MP) appears to be faster than that of ethyl propanoate (EP) under the present experimental conditions, where CO and CO 2 reach their plateau values faster for MP at a specific temperature and fuel concentration. Higher plateau values are reached for CO in case of MP while the CO2 levels are similar for the two ester fuels. Ethylene production is larger for EP due to the presence of six-centered ring elimination reaction that produces ethylene and propanoic acid. Very little H2O is produced during MP pyrolysis in contrast with appreciable H2O production from EP. Sensitivity and rate-of-production analyses were carried out to identify key reactions that affect the measured species profiles. Previous kinetic mechanisms of Yang et al. (2011) [1,2] and Metcalf et al. (2009, 2007) [3,4] were used as base models and then refined to propose a new MP/EP pyrolysis mechanism. © 2014 Elsevier Ltd. All rights reserved.

A comparative study of the chemical kinetics of methyl and ethyl propanoate

KAUST Repository

Farooq, Aamir; Davidson, D.F.; Hanson, R.K.; Westbrook, C.K.

2014-01-01

High temperature pyrolysis of methyl propanoate (CH3CH 2C(O)OCH3) and ethyl propanoate (CH3CH 2C(O)OCH2CH3) was studied behind reflected shock waves at temperatures of 1250-1750 K and pressure of 1.5 atm. Species time-histories were recorded for CO, CO2, C2H4, and H2O using laser absorption methods over a test time of 1 ms. Pyrolysis of methyl propanoate (MP) appears to be faster than that of ethyl propanoate (EP) under the present experimental conditions, where CO and CO 2 reach their plateau values faster for MP at a specific temperature and fuel concentration. Higher plateau values are reached for CO in case of MP while the CO2 levels are similar for the two ester fuels. Ethylene production is larger for EP due to the presence of six-centered ring elimination reaction that produces ethylene and propanoic acid. Very little H2O is produced during MP pyrolysis in contrast with appreciable H2O production from EP. Sensitivity and rate-of-production analyses were carried out to identify key reactions that affect the measured species profiles. Previous kinetic mechanisms of Yang et al. (2011) [1,2] and Metcalf et al. (2009, 2007) [3,4] were used as base models and then refined to propose a new MP/EP pyrolysis mechanism. © 2014 Elsevier Ltd. All rights reserved.

A Simple and Fast Method for the Production and Characterization of Methylic and Ethylic Biodiesels from Tucum Oil via an Alkaline Route

Directory of Open Access Journals (Sweden)

Marcelo Firmino de Oliveira

2011-01-01

Full Text Available A simple, fast, and complete route for the production of methylic and ethylic biodiesel from tucum oil is described. Aliquots of the oil obtained directly from pressed tucum (pulp and almonds were treated with potassium methoxide or ethoxide at 40°C for 40 min. The biodiesel form was removed from the reactor and washed with 0.1 M HCl aqueous solution. A simple distillation at 100°C was carried out in order to remove water and alcohol species from the biodiesel. The oxidative stability index was obtained for the tucum oil as well as the methylic and ethylic biodiesel at 6.13, 2.90, and 2.80 h, for storage times higher than 8 days. Quality control of the original oil and of the methylic and ethylic biodiesels, such as the amount of glycerin produced during the transesterification process, was accomplished by the TLC, GC-MS, and FT-IR techniques. The results obtained in this study indicate a potential biofuel production by simple treatment of tucum, an important Amazonian fruit.

Synthesis of N-methyl and N-11C-methyl spiperone by phase transfer catalysis in anhydrous solvent

International Nuclear Information System (INIS)

Omokawa, Hiroyoshi; Tanaka, Akira; Iio, Mayumi; Nishihara, Yoshiaki; Inoue, Osamu; Yamazaki, Toshio.

1985-01-01

Spiperone, a butyrophenone neuroleptic drug, has been used in binding studies of dopamine receptors. Langstrom et al. developed N- 11 C-methyl spiperone, and, in cooperate with Wagner et al., made it possible to visualize the distribution of dopamine receptors in the human brain in vivo. In this paper, we independently developed another synthetic method of N- 11 C-methyl spiperone using the phase transfer catalyst in an anhydrous solvent. Separation of the product is feasible only by passing the reactant solution through a Millipore filter and injecting it onto high pressure liquid chromatography (HPLC). The time required for the synthesis and purification of N- 11 C-methyl spiperone from 11 C-methyl iodide and spiperone was 20 min. Radiochemical yield exceeded 35 % against 11 C-methyl iodide without correcting decay of the radioactivity. (author)

Mechanism of inactivation of human leukocyte elastase by a chloromethyl ketone: kinetic and solvent isotope effect studies

International Nuclear Information System (INIS)

Stein, R.L.; Trainor, D.A.

1986-01-01

The mechanism of inactivation of human leukocyte elastase (HLE) by the chloromethyl ketone MeOSuc-Ala-Ala-Pro-Val-CH 2 Cl was investigated. The dependence of the first-order rate constant for inactivation on concentration of chloromethyl ketone is hyperbolic and suggests formation of a reversible Michaelis complex prior to covalent interaction between the enzyme and inhibitor. However, the observed Ki value is 10 microM, at least 10-fold lower than dissociation constants for complexes formed from interaction of HLE with structurally related substrates or reversible inhibitors, and suggests that Ki is a complex kinetic constant, reflecting the formation and accumulation of both the Michaelis complex and a second complex. It is proposed that this second complex is a hemiketal formed from attack of the active site serine on the carbonyl carbon of the inhibitor. The accumulation of this intermediate may be a general feature of reactions of serine proteases and chloromethyl ketones derived from specific peptides and accounts for the very low Ki values observed for these reactions. The solvent deuterium isotope effect (SIE) on the inactivation step (ki) is 1.58 +/- 0.07 and is consistent with rate-limiting, general-catalyzed attack of the active site His on the methylene carbon of the inhibitor with displacement of chloride anion. The general catalyst is thought to be the active site Asp. In contrast, the SIE on the second-order rate constant for HLE inactivation, ki/Ki, is inverse and equals 0.64 +/- 0.05

Searching for trans ethyl methyl ether in Orion KL★,★★

Science.gov (United States)

Tercero, B.; Cernicharo, J.; López, A.; Brouillet, N.; Kolesniková, L.; Motiyenko, R. A.; Margulès, L.; Alonso, J. L.; Guillemin, J.-C.

2015-01-01

We report on the tentative detection of trans ethyl methyl ether (tEME), t-CH3CH2OCH3, through the identification of a large number of rotational lines from each one of the spin states of the molecule towards Orion KL. We also search for gauche-trans-n-propanol, Gt-n-CH3CH2CH2OH, an isomer of tEME in the same source. We have identified lines of both species in the IRAM 30 m line survey and in the ALMA Science Verification data. We have obtained ALMA maps to establish the spatial distribution of these species. Whereas tEME mainly arises from the compact ridge component of Orion, Gt-n-propanol appears at the emission peak of ethanol (south hot core). The derived column densities of these species at the location of their emission peaks are ≤(4.0 ± 0.8) × 1015 cm−2 and ≤(1.0 ± 0.2)× 1015 cm−2 for tEME and Gt-n-propanol, respectively. The rotational temperature is ~100 K for both molecules. We also provide maps of CH3OCOH, CH3CH2OCOH, CH3OCH3, CH3OH, and CH3CH2OH to compare the distribution of these organic saturated O-bearing species containing methyl and ethyl groups in this region. Abundance ratios of related species and upper limits to the abundances of non-detected ethers are provided. We derive an abundance ratio N(CH3OCH3)/N(tEME) ≥ 150 in the compact ridge of Orion. PMID:26869726

The combustion kinetics of the lignocellulosic biofuel, ethyl levulinate

KAUST Repository

Ghosh, Manik Kumer; Howard, Mí cheá l Sé amus; Zhang, Yingjia; Djebbi, Khalil; Capriolo, Gianluca; Farooq, Aamir; Curran, Henry J.; Dooley, Stephen

2018-01-01

Ethyl levulinate (Ethyl 4-oxopentanoate) is a liquid molecule at ambient temperature, comprising of ketone and ethyl ester functionalities and is one of the prominent liquid fuel candidates that may be easily obtained from lignocellulosic biomass. The combustion kinetics of ethyl levulinate have been investigated. Shock tube and rapid compression machine apparatuses are utilised to acquire gas phase ignition delay measurements of 0.5% ethyl levulinate/O2 mixtures at ϕ = 1.0 and ϕ = 0.5 at ∼ 10 atm over the temperature range 1000–1400 K. Ethyl levulinate is observed not to ignite at temperatures lower than ∼1040 K in the rapid compression machine. The shock tube and rapid compression machine data are closely consistent and show ethyl levulinate ignition delay to exhibit an Arrhenius dependence to temperature. These measurements are explained by the construction and analysis of a detailed chemical kinetic model. The kinetic model is completed by establishing thermochemical-kinetic analogies to 2-butanone, for the ethyl levulinate ketone functionality, and to ethyl propanoate for the ethyl ester functionality. The so constructed model is observed to describe the shock tube data very accurately, but computes the rapid compression machine data set to a lesser but still applicable fidelity. Analysis of the model suggests the autooxidation mechanism of ethyl levulinate to be entirely dominated by the propensity for the ethyl ester functionality to unimolecularly decompose to form levulinic acid and ethylene. The subsequent reaction kinetics of these species is shown to dictate the overall rate of the global combustion reaction. This model is then use to estimate the Research and Motored Octane Numbers of ethyl levulinate to be ≥97.7 and ≥ 93, respectively. With this analysis ethyl levulinate would be best suited as a gasoline fuel component, rather than as a diesel fuel as suggested in the literature. Indeed it may be considered to be useful as an

The combustion kinetics of the lignocellulosic biofuel, ethyl levulinate

KAUST Repository

Ghosh, Manik Kumer

2018-04-04

Ethyl levulinate (Ethyl 4-oxopentanoate) is a liquid molecule at ambient temperature, comprising of ketone and ethyl ester functionalities and is one of the prominent liquid fuel candidates that may be easily obtained from lignocellulosic biomass. The combustion kinetics of ethyl levulinate have been investigated. Shock tube and rapid compression machine apparatuses are utilised to acquire gas phase ignition delay measurements of 0.5% ethyl levulinate/O2 mixtures at ϕ = 1.0 and ϕ = 0.5 at ∼ 10 atm over the temperature range 1000–1400 K. Ethyl levulinate is observed not to ignite at temperatures lower than ∼1040 K in the rapid compression machine. The shock tube and rapid compression machine data are closely consistent and show ethyl levulinate ignition delay to exhibit an Arrhenius dependence to temperature. These measurements are explained by the construction and analysis of a detailed chemical kinetic model. The kinetic model is completed by establishing thermochemical-kinetic analogies to 2-butanone, for the ethyl levulinate ketone functionality, and to ethyl propanoate for the ethyl ester functionality. The so constructed model is observed to describe the shock tube data very accurately, but computes the rapid compression machine data set to a lesser but still applicable fidelity. Analysis of the model suggests the autooxidation mechanism of ethyl levulinate to be entirely dominated by the propensity for the ethyl ester functionality to unimolecularly decompose to form levulinic acid and ethylene. The subsequent reaction kinetics of these species is shown to dictate the overall rate of the global combustion reaction. This model is then use to estimate the Research and Motored Octane Numbers of ethyl levulinate to be ≥97.7 and ≥ 93, respectively. With this analysis ethyl levulinate would be best suited as a gasoline fuel component, rather than as a diesel fuel as suggested in the literature. Indeed it may be considered to be useful as an

Use of a holder-vacuum tube device to save on-site hands in preparing urine samples for head-space gas-chromatography, and its application to determine the time allowance for sample sealing.

Science.gov (United States)

Kawai, Toshio; Sumino, Kimiaki; Ohashi, Fumiko; Ikeda, Masayuki

2011-01-01

To facilitate urine sample preparation prior to head-space gas-chromatographic (HS-GC) analysis. Urine samples containing one of the five solvents (acetone, methanol, methyl ethyl ketone, methyl isobutyl ketone and toluene) at the levels of biological exposure limits were aspirated into a vacuum tube via holder, a device commercially available for venous blood collection (the vacuum tube method). The urine sample, 5 ml, was quantitatively transferred to a 20-ml head-space vial prior to HS-GC analysis. The loaded tubes were stored at +4 ℃ in dark for up to 3 d. The vacuum tube method facilitated on-site procedures of urine sample preparation for HS-GC with no significant loss of solvents in the sample and no need of skilled hands, whereas on-site sample preparation time was significantly reduced. Furthermore, no loss of solvents was detected during the 3-d storage, irrespective of hydrophilic (acetone) or lipophilic solvent (toluene). In a pilot application, high performance of the vacuum tube method in sealing a sample in an air-tight space succeeded to confirm that no solvent will be lost when sealing is completed within 5 min after urine voiding, and that the allowance time is as long as 30 min in case of toluene in urine. The use of the holder-vacuum tube device not only saves hands for transfer of the sample to air-tight space, but facilitates sample storage prior to HS-GC analysis.

Thermophysical properties of biodiesel and related systems: Low-pressure vapor + liquid equilibrium of methyl/ethyl soybean biodiesel

International Nuclear Information System (INIS)

Veneral, Josamaique G.; Junior, Dirceu L.R.; Mazutti, Marcio A.; Voll, Fernando A.P.; Cardozo-Filho, Lúcio; Corazza, Marcos L.; Silva, Edson A.; Oliveira, J. Vladimir

2013-01-01

Highlights: • Boiling point temperatures for soybean FAME and FAEE measured in the pressure range of (6.7 to 66.7) kPa. • Investigated systems presented a non-ideal behavior, with positive deviations from Raoult’s law. • Experimental data satisfactorily represented by the UNIQUAC model. -- Abstract: In this work, experimental boiling point temperatures for pseudo-binaries (methyl/ethyl biodiesel + methanol/ethanol) and pseudo-ternaries (methyl/ethyl biodiesel + methanol/ethanol + glycerol/water) systems were measured at several pressures ranging from (6.7 to 66.7) kPa using an Othmer-type ebulliometer. The systems investigated show a non-ideal behavior, with positive deviations from Raoult’s law. It was observed that the addition of up to 10 wt% of alcohol (methanol or ethanol) led to a significant decrease in the boiling point temperature of the systems. The UNIQUAC model was successfully used to represent the experimental results, with an overall average deviation between experimental and calculated boiling temperature values of 0.004%

Graphene-Fiber-Based Supercapacitors Favor N-Methyl-2-pyrrolidone/Ethyl Acetate as the Spinning Solvent/Coagulant Combination.

Science.gov (United States)

He, Nanfei; Pan, Qin; Liu, Yixin; Gao, Wei

2017-07-26

One-dimensional flexible fiber supercapacitors (FSCs) have attracted great interest as promising energy-storage units that can be seamlessly incorporated into textiles via weaving, knitting, or braiding. The major challenges in this field are to develop tougher and more efficient FSCs with a relatively easy and scalable process. Here, we demonstrate a wet-spinning process to produce graphene oxide (GO) fibers from GO dispersions in N-methyl-2-pyrrolidone (NMP), with ethyl acetate as the coagulant. Upon chemical reduction of GO, the resulting NMP-based reduced GO (rGO) fibers (rGO@NMP-Fs) are twice as high in the surface area and toughness but comparable in tensile strength and conductivity as that of the water-based rGO fibers (rGO@H 2 O-Fs). When assembled into parallel FSCs, rGO@NMP-F-based supercapacitors (rGO@NMP-FSCs) offered a specific capacitance of 196.7 F cm -3 (147.5 mF cm -2 ), five times higher than that of rGO@H 2 O-F-based supercapacitors (rGO@H 2 O-FSCs) and also higher than most existing wet-spun rGO-FSCs, as well as those FSCs built with metal wires, graphene/carbon nanotube (CNT) fibers, or even pseudocapacitive materials. In addition, our rGO@NMP-FSCs can provide good bending and cycling stability. The energy density of our rGO@NMP-FSCs reaches ca. 6.8 mWh cm -3 , comparable to that of a Li thin-film battery (4 V/500 μAh).

Food Simulating Organic Solvents for Evaluating Crosslink Density of Bulk Fill Composite Resin

Directory of Open Access Journals (Sweden)

Neveen M. Ayad

2017-01-01

Full Text Available Objectives. To evaluate crosslink densities of two bulk fill composite resins and determine if the used Food Simulating Organic Solvent (FSOS affected them. Methods. Forty specimens were prepared from SureFill and SonicFill bulk fill composite resins, 20 each. All specimens were stored dry for 24 h. Each group was divided into 2 subgroups: stored in ethanol (E 75% or in methyl ethyl ketone (MEK 100% for 24 h. Crosslink density was evaluated by calculating the difference between the Vickers hardness numbers of the specimens stored dry and after their storage in FSOS. The data were statistically analyzed using t-test. Results. The means of crosslink density in E and MEK were 6.99% and 9.44% for SureFill and 10.54% and 11.92% for SonicFill, respectively. t-test displayed significant differences between crosslink densities of SureFill and SonicFill: (P<0.0001 in E and (P=0.02 in MEK and between crosslink densities of SureFill in E and MEK (P=0.02. Conclusions. Crosslink density of bulk fill composite resin can be evaluated using E or MEK. SureFill has higher crosslink density than SonicFill in both E and MEK.

Environmental Assessment: 2005 Base Realignment and Closure Seymour Johnson Air Force Base Goldsboro, North Carolina

Science.gov (United States)

2007-07-01

aquatica), red maple (Acer rubrum), and loblolly pine ( Pinus taeda) are also present. • Coastal Plain Small Stream Swamp: Degraded examples of this...Daily Permit Limit (lbs/hr) Emissions (lbs/hr) (lbs/hr) Emissions (lbs/day) Emissions (lbs/day) (lbs/day) Ethyl Acetate 0 0 481.8 - - -- Methyl Ethyl...Ketone 0.54 1.08 34.1 2.7 5.4 76.2 Methyl Isobutyl Ketone 0.41 0.82 105.6 2.05 4.1 2247.7 Toluene 0.71 1.42 23.8 3.55 7.1 571.4 Xylene 0.33 0.66

4-Hydroxy-3-methyl-6-phenylbenzofuran-2-carboxylic acid ethyl ester derivatives as potent anti-tumor agents.

Science.gov (United States)

Hayakawa, Ichiro; Shioya, Rieko; Agatsuma, Toshinori; Furukawa, Hidehiko; Naruto, Shunji; Sugano, Yuichi

2004-01-19

Based on the structure of 4-hydroxy-3-methyl-6-phenylbenzofuran-2-carboxylic acid ethyl ester (1), which exhibits selective cytotoxicity against a tumorigenic cell line, (2,4-dimethoxyphenyl)-(4-hydroxy-3-methyl-6-phenylbenzofuran-2-yl)-methanone (18m) was designed and synthesized as a biologically stable derivative containing no ester group. Although the potency of 18m was almost the same as our initial hit compound 1, 18m is expected to last longer in the human body as an anticancer agent.

Thermodynamic models for determination of 3-chloro-N-phenylphthalimide solubility in binary solvent mixtures of (acetone, ethyl acetate or 1,4-dioxane + methanol)

International Nuclear Information System (INIS)

Xie, Yong; Shi, Hongwei; Du, Cunbin; Cong, Yang; Wang, Jian; Zhao, Hongkun

2016-01-01

Highlights: • Solubility of 3-chloro-N-phenylphthalimide in binary mixed solvents were determined. • Solubility data were correlated and calculated by five models. • The standard molar enthalpy for the dissolution processes were calculated. - Abstract: The solubility of 3-chloro-N-phenylphthalimide in binary mixed solvents of (acetone + methanol, ethyl acetate + methanol and 1,4-dioxane + methanol) were determined experimentally by using the isothermal dissolution equilibrium method within the temperature range from (288.15 to 323.15) K under atmosphere pressure. For the binary systems of (acetone + methanol) and (1,4-dioxane + methanol), the solubility of 3-chloro-N-phenylphthalimide increased with increasing temperature and mass fraction of acetone or 1,4-dioxane; and for the (ethyl acetate + methanol) system, at a given composition of ethyl acetate, the solubility of 3-chloro-N-phenylphthalimide increased with an increase in temperature; nevertheless at the same temperature, they increased at first and then decreased with increasing mass fraction of 1,4-dioxane. At the same temperature and mass fraction of acetone, ethyl acetate or 1,4-dioxane, the solubility of 3-chloro-N-phenylphthalimide was greater in (1,4-dioxane + methanol) than in the other two mixed solvents. The solubility values were correlated by employing the Jouyban–Acree model, van’t Hoff–Jouyban–Acree model, Apelblat–Jouyban–Acree model, Ma model, and Sun model. On the whole, the Ma model and Sun model were proven to provide good representation of the experimental solubility results. Furthermore, the dissolution enthalpies of the dissolution process were calculated. The dissolution process of 3-chloro-N-phenylphthalimide in these mixed solvents is endothermic. The experimental solubility and the models in this study could be helpful in purifying 3-chloro-N-phenylphthalimide.

Supercritical antisolvent co-precipitation of rifampicin and ethyl cellulose.

Science.gov (United States)

Djerafi, Rania; Swanepoel, Andri; Crampon, Christelle; Kalombo, Lonji; Labuschagne, Philip; Badens, Elisabeth; Masmoudi, Yasmine

2017-05-01

Rifampicin-loaded submicron-sized particles were prepared through supercritical anti-solvent process using ethyl cellulose as polymeric encapsulating excipient. Ethyl acetate and a mixture of ethyl acetate/dimethyl sulfoxide (70/30 and 85/15) were used as solvents for both drug and polymeric excipient. When ethyl acetate was used, rifampicin was crystallized separately without being embedded within the ethyl cellulose matrix while by using the ethyl acetate/dimethyl sulfoxide mixture, reduced crystallinity of the active ingredient was observed and a simultaneous precipitation of ethyl cellulose and drug was achieved. The effect of solvent/CO 2 molar ratio and polymer/drug mass ratio on the co-precipitates morphology and drug loading was investigated. Using the solvent mixture, co-precipitates with particle sizes ranging between 190 and 230nm were obtained with drug loading and drug precipitation yield from respectively 8.5 to 38.5 and 42.4 to 77.2% when decreasing the ethyl cellulose/rifampicin ratio. Results show that the solvent nature and the initial drug concentrations affect morphology and drug precipitation yield of the formulations. In vitro dissolution studies revealed that the release profile of rifampicin was sustained when co-precipitation was carried out with the solvent mixture. It was demonstrated that the drug to polymer ratio influenced amorphous content of the SAS co-precipitates. Differential scanning calorimetry thermograms and infrared spectra revealed that there is neither interaction between rifampicin and the polymer nor degradation of rifampicin during co-precipitation. In addition, stability stress tests on SAS co-precipitates were carried out at 75% relative humidity and room temperature in order to evaluate their physical stability. SAS co-precipitates were X-ray amorphous and remained stable after 6months of storage. The SAS co-precipitation process using a mixture of ethyl acetate/dimethyl sulfoxide demonstrates that this strategy can

Methyl and ethyl soybean esters production

Energy Technology Data Exchange (ETDEWEB)

Pighinelli, Anna Leticia Montenegro Turtelli; Park, Kil Jin; Zorzeto, Thais Queiroz [Universidade Estadual de Campinas (FEAGRI/UNICAMP), SP (Brazil). Fac. de Engenharia Agricola], E-mail: annalets@feagri.unicamp.br; Bevilaqua, Gabriela [Universidade Estadual de Campinas (IQ/UNICAMP), SP (Brazil). Inst. de Quimica

2008-07-01

Biodiesel is a fuel obtained from triglycerides found in nature, like vegetable oils and animal fats. Nowadays it has been the subject of many researches impulses by the creation of the Brazilian law that determined the blend of 2% of biodiesel with petrodiesel. Basically, there are no limitations on the oilseed type for chemical reaction, but due to high cost of this major feedstock, it is important to use the grain that is available in the region of production. Soybean is the oilseed mostly produced in Brazil and its oil is the only one that is available in enough quantity to supply the current biodiesel demand. The objective of this work was to study the effects of reaction time and temperature on soybean oil transesterification reaction with ethanol and methanol. A central composite experimental design with five variation levels was used and response surface methodology applied for the data analysis. The statistical analysis of the results showed that none of the factors affected the ethyl esters production. However, the methyl esters production suffered the influence of temperature (linear effect), reaction time (linear and quadratic) and interaction of these two variables. None of the generated models showed significant regression consequently it was not possible to build the response surface. The experiments demonstrated that methanol is the best alcohol for transesterification reactions and the ester yield was up to 85%. (author)

(Vapour + liquid) equilibria, volumetric and compressibility behaviour of binary and ternary aqueous solutions of 1-hexyl-3-methylimidazolium chloride, methyl potassium malonate, and ethyl potassium malonate

International Nuclear Information System (INIS)

Sadeghi, Rahmat; Mahdavi, Adibeh

2012-01-01

Highlights: ► VLE and volumetry of binary and ternary [C 6 mim][Cl], MPM and EPM aqueous solutions. ► Constant a w lines show small negative deviation from the linear isopiestic relation. ► Solute–water interactions follow the order: EPM > MPM > [C 6 mim][Cl]. ► MPM and EPM have a very weak salting-out effect on [C 6 mim][Cl] aqueous solutions. - Abstract: (Vapour + liquid) equilibrium data (water activity, vapour pressure, osmotic coefficient, and activity coefficient) of binary aqueous solutions of 1-hexyl-3-methylimidazolium chloride ([C 6 mim][Cl]), methyl potassium malonate, and ethyl potassium malonate and ternary {[C 6 mim][Cl] + methyl potassium malonate} and {[C 6 mim][Cl] + ethyl potassium malonate} aqueous solutions were obtained through the isopiestic method at T = 298.15 K. These results reveal that the ionic liquid behaves as surfactant-like and aggregates in aqueous solutions at molality about 0.4 mol · kg −1 . The constant water activity lines of all the ternary systems investigated show small negative deviations from the linear isopiestic relation (Zdanovskii–Stokes–Robinson rule) derived using the semi-ideal hydration model. The density and speed of sound measurements were carried out on solutions of methyl potassium malonate and ethyl potassium malonate in water and of [C 6 mim][Cl] in aqueous solutions of 0.25 mol · kg −1 methyl potassium malonate and ethyl potassium malonate at T = (288.15 to 308.15) K at atmospheric pressure. From the experimental density and speed of sound data, the values of the apparent molar volume, apparent molar isentropic compressibility and excess molar volume were evaluated and from which the infinite dilution apparent molar volume and infinite dilution apparent molar isentropic compressibility were calculated at each temperature. Although, there are no clear differences between the values of the apparent molar volume of [C 6 mim][Cl] in pure water and in methyl potassium malonate or ethyl

Solid acid catalysed formation of ethyl levulinate and ethyl glucopyranoside from mono- and disaccharides

DEFF Research Database (Denmark)

Shunmugavel, Saravanamurugan; Riisager, Anders

2012-01-01

Sulfonic acid functionalised SBA-15 (SO3H-SBA-15), sulfated zirconia and beta, Y, ZSM-5 and mordenite zeolite catalysts have been applied for the dehydration of sugars to ethyl levulinate and ethyl-D-glucopyranoside (EDGP) using ethanol as solvent and reactant. The SO3H-SBA-15 catalyst showed...

1,5-Asymmetric induction in the boron-mediated aldol reaction of β-oxygenated methyl ketones

International Nuclear Information System (INIS)

Dias, Luiz C.

2007-01-01

High levels of substrate-based 1,5-stereo induction are obtained in the boron-mediated aldol reactions of β-oxygenated methyl ketones with achiral and chiral aldehydes. Remote induction from the boron enolates gives the 1,5-anti adducts, with the enolate pi-facial selectivity critically dependent upon the nature of the beta-alkoxy protecting group. This 1,5-anti aldol methodology has been strategically employed in the total synthesis of several natural products. At present, the origin of the high level of 1,5-anti induction obtained with the boron enolates is unclear, although a model based on a hydrogen bonding between the alkoxy oxygen and the formyl hydrogen has been recently proposed. (author)

Biological effects of methyl and ethyl mercury compounds used as disinfectants for seed-grain on domestic and wild life

Energy Technology Data Exchange (ETDEWEB)

Tejning, S

1971-01-01

A short survey of the harmful effects of methyl and ethyl mercury on wild and domestic life and on man since the introduction of these compounds in plant protection is given. The biological effects of methyl mercury in birds are illustrated by experiments in hens concerning its accumulation in their organs and plumage, its elimination in eggs and excrements and its influence on the health of the birds, their laying habits and egg production including the occurrence of embryonic damages and the hatchability. Attention is drawn to the ability of methyl mercury to cause genetical disorders. 14 references, 1 figure, 1 table.

Direct Synthesis of Renewable Dodecanol and Dodecane with Methyl Isobutyl Ketone over Dual-Bed Catalyst Systems.

Science.gov (United States)

Sheng, Xueru; Li, Ning; Li, Guangyi; Wang, Wentao; Wang, Aiqin; Cong, Yu; Wang, Xiaodong; Zhang, Tao

2017-03-09

For the first time, we demonstrated two integrated processes for the direct synthesis of dodecanol or 2,4,8-trimethylnonane (a jet fuel range C 12 -branched alkane) using methyl isobutyl ketone (MIBK) that can be derived from lignocellulose. The reactions were carried out in dual-bed continuous flow reactors. In the first bed, MIBK was selectively converted to a mixture of C 12 alcohol and ketone. Over the Pd-modified magnesium- aluminium hydrotalcite (Pd-MgAl-HT) catalyst, a high total carbon yield (73.0 %) of C 12 oxygenates can be achieved under mild conditions. In the second bed, the C 12 oxygenates generated in the first bed were hydrogenated to dodecanol over a Ru/C catalyst or hydrodeoxygenated to 2,4,8-trimethylnonane over a Cu/SiO 2 catalyst. The as-obtained dodecanol can be used as feedstock in the production of sodium dodecylsulfate (SDS) and sodium dodecyl benzene sulfonate (SDBS), which are widely used as surfactants or detergents. The asobtained 2,4,8-trimethylnonane can be blended into conventional jet fuel without hydroisomerization. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Solvent production by engineered Ralstonia eutropha: channeling carbon to biofuel.

Science.gov (United States)

Chakravarty, Jayashree; Brigham, Christopher J

2018-06-01

Microbial production of solvents like acetone and butanol was a couple of the first industrial fermentation processes to gain global importance. These solvents are important feedstocks for the chemical and biofuel industry. Ralstonia eutropha is a facultatively chemolithoautotrophic bacterium able to grow with organic substrates or H 2 and CO 2 under aerobic conditions. This bacterium is a natural producer of polyhydroxyalkanoate biopolymers. Recently, with the advances in the development of genetic engineering tools, the range of metabolites R. eutropha can produce has enlarged. Its ability to utilize various carbon sources renders it an interesting candidate host for synthesis of renewable biofuel and solvent production. This review focuses on progress in metabolic engineering of R. eutropha for the production of alcohols, terpenes, methyl ketones, and alka(e)nes using various resources. Biological synthesis of solvents still presents the challenge of high production costs and competition from chemical synthesis. Better understanding of R. eutropha biology will support efforts to engineer and develop superior microbial strains for solvent production. Continued research on multiple fronts is required to engineer R. eutropha for truly sustainable and economical solvent production.

Ternary and binary LLE measurements for solvent (2-methyltetrahydrofuran and cyclopentyl methyl ether) + furfural + water between 298 and 343 K

International Nuclear Information System (INIS)

Männistö, Mikael; Pokki, Juha-Pekka; Fournis, Ludivine; Alopaeus, Ville

2017-01-01

Highlights: • Novel LLE of 2-methyltetrahydrofuran or cyclopentyl methyl ether + furfural + water. • High performance solvents for liquid-liquid extraction exhibited. • Modelled with UNIQUAC-HOC activity coefficient model. • Comparison to other industrial solvents with distribution coefficient and selectivity. - Abstract: The suitability of two solvents for the extraction of furfural from aqueous streams is assessed through novel ternary and binary liquid-liquid equilibria data for mixtures of solvent (2-methyltetrahydrofuran or cyclopentyl methyl ether) + furfural + water. The measured data are reported along with regressed binary interaction parameters for UNIQUAC-HOC activity coefficient model and further analyzed through distribution coefficients and selectivity for furfural. Out of the two solvents, cyclopentyl methyl ether presents a very high selectivity along with good distribution coefficient in the entire temperature range.

Report on Scientific Basis for Paint Stripping: Mechanism of Methylene Chloride Based Paint Removers

Science.gov (United States)

2011-10-20

observing NMR of the solvent molecules themselves, 1H NMR can be useful in more highly swollen cases such as chloroform in copolymer gel beads,14 or in...Polyurethane Topcoat. Part A Raw Material Wt % Part B Raw Material Wt % Methyl N- propyl ketone 1 Polyurethane resin 43 Methyl N-amyl ketone 7 N-Butyl...2 5.5 N-Butyl acetate 2 Methyl N-amyl ketone 8.9 Methyl N- propyl ketone 1.3 Anti-oxidant 0.4 UV absorber 0.6 UV Stabilizer 1.3

Fabrication of porous ethyl cellulose microspheres based on the acetone-glycerin-water ternary system: Controlling porosity via the solvent-removal mode.

Science.gov (United States)

Murakami, Masahiro; Matsumoto, Akihiro; Watanabe, Chie; Kurumado, Yu; Takama, Masashi

2015-08-01

Porous ethyl cellulose (EC) microspheres were prepared from the acetone-glycerin-water ternary system using an oil/water (O/W)-type emulsion solvent extraction method. The O/ W type emulsion was prepared using acetone dissolved ethyl cellulose as an oil phase and aqueous glycerin as a water phase. The effects of the different solvent extraction modes on the porosity of the microspheres were investigated. The specific surface area of the porous EC microspheres was estimated by the gas adsorption method. When the solvent was extracted rapidly by mixing the emulsion with water instantaneously, porous EC microspheres with a maximum specific surface area of 40.7±2.1 m2/g were obtained. On the other hand, when water was added gradually to the emulsion, the specific surface area of the fabricated microspheres decreased rapidly with an increase in the infusion period, with the area being 25-45% of the maximum value. The results of an analysis of the ternary phase diagram of the system suggested that the penetration of water and glycerin from the continuous phase to the dispersed phase before solidification affected the porosity of the fabricated EC microspheres.

Groundwater remediation project at Stockem railway station following a pollution with MIAK (Methyl Isoamyl Ketone)

Energy Technology Data Exchange (ETDEWEB)

Daelemans, A.; Boden, A.; Schuyteneer, L.W. de; Achter, L.H. van [Soil Service of Belgium, Leuven-Heverlee (Belgium)

2003-07-01

On the 20{sup th} of January 2000, a derailment accident happened near the railway station of Stockem in the vicinity of the city of Arlon. An estimated 20.000 litres of MIAK (methyl isoamyl ketone or 5-methyl-2-hexanone) was spilled and lost into the soil. Immediately after the accident, the Soil Service of Belgium received a request from the Belgian National Railway Company to establish an emergency plan for the remediation of the spill, including the design and the follow-up of the clean up operations. The calamity happened to the West of the railway station at a height of 360 m above sea level and in the vicinity of the Semois river (200 m to the South). From a geological point of view, the Formation of Florenville is outcropping at the site. This formation is characterized by an alternation of sandy sediments and sandstone layers. Locally the rock layer are porous allowing vertical migration of the water. The formation is an important but vulnerable aquifer. Further to the South, water is extracted from the aquifer in large quantities for both public distribution and bottling purposes. The spilled product, 5-methyl-2-hexanone (MIAK), has a typical fruity odour and its density is slightly lower than water. The product is relative mobile and fairly easy degraded biologically in low concentrations. (orig.)

Fluoro-Carbonate Solvents for Li-Ion Cells

International Nuclear Information System (INIS)

NAGASUBRAMANIAN, GANESAN

1999-01-01

A number of fluoro-carbonate solvents were evaluated as electrolytes for Li-ion cells. These solvents are fluorine analogs of the conventional electrolyte solvents such as dimethyl carbonate, ethylene carbonate, diethyl carbonate in Li-ion cells. Conductivity of single and mixed fluoro carbonate electrolytes containing 1 M LiPF(sub 6) was measured at different temperatures. These electrolytes did not freeze at -40 C. We are evaluating currently, the irreversible 1st cycle capacity loss in carbon anode in these electrolytes and the capacity loss will be compared to that in the conventional electrolytes. Voltage stability windows of the electrolytes were measured at room temperature and compared with that of the conventional electrolytes. The fluoro-carbon electrolytes appear to be more stable than the conventional electrolytes near Li voltage. Few preliminary electrochemical data of the fluoro-carbonate solvents in full cells are reported in the literature. For example, some of the fluorocarbonate solvents appear to have a wider voltage window than the conventional electrolyte solvents. For example, methyl 2,2,2 trifluoro ethyl carbonate containing 1 M LiPF(sub 6) electrolyte has a decomposition voltage exceeding 6 V vs. Li compared to and lt;5 V for conventional electrolytes. The solvent also appears to be stable in contact with lithium at room temperature

Environmental analysis of the life cycle emissions of 2-methyl tetrahydrofuran solvent manufactured from renewable resources.

Science.gov (United States)

Slater, C Stewart; Savelski, Mariano J; Hitchcock, David; Cavanagh, Eduardo J

2016-01-01

An environmental analysis has been conducted to determine the cradle to gate life cycle emissions to manufacture the green solvent, 2-methyl tetrahydrofuran. The solvent is considered a greener chemical since it can be manufactured from renewable resources with a lower life cycle footprint. Analyses have been performed using different methods to show greenness in both its production and industrial use. This solvent can potentially be substituted for other ether and chlorinated solvents commonly used in organometallic and biphasic reactions steps in pharmaceutical and fine chemical syntheses. The 2-methyl tetrahydrofuran made from renewable agricultural by-products is marketed by Penn A Kem under the name ecoMeTHF™. The starting material, 2-furfuraldehyde (furfural), is produced from corn cob waste by converting the available pentosans by acid hydrolysis. An evaluation of each step in the process was necessary to determine the overall life cycle and specific CO2 emissions for each raw material/intermediate produced. Allocation of credits for CO2 from the incineration of solvents made from renewable feedstocks significantly reduced the overall carbon footprint. Using this approach, the overall life cycle emissions for production of 1 kg of ecoMeTHF™ were determined to be 0.191 kg, including 0.150 kg of CO2. Life cycle emissions generated from raw material manufacture represents the majority of the overall environmental impact. Our evaluation shows that using 2-methyl tetrahydrofuran in an industrial scenario results in a 97% reduction in emissions, when compared to typically used solvents such as tetrahydrofuran, made through a conventional chemical route.

Solvent extraction of Au(III) for preparation of a carrier-free multitracer and an Au tracer from an Au target

International Nuclear Information System (INIS)

Weginwar, R.G.; Kobayashi, Y.; Ambe, S.; Liu, B.; Enomoto, S.; Ambe, F.

1996-01-01

Separation of Au(III) and various carrier-free radionuclides by solvent extraction was investigated using an Au target irradiated by an energetic heavy-ion beam. Percentage extraction of Au(III) and coextraction of the radionuclides were determined with varying parameters such as kinds of solvent, molarity of HCl or pH, and Au concentration. Under the conditions where Au(III) was effectively extracted, namely extraction with ethyl acetate or isobutyl methyl ketone from 3 mol*dm -3 HCl, carrier-free radionuclides of many elements were found to be more or less coextracted. Coextraction of radionuclides of some elements was found to increase with an increase in the concentration of Au(III). This finding is ascribed to the formation of strong association of the complex of these elements with chloroauric acid. In order to avoid serious loss of these elements by the extraction, lowering of the Au(III) concentration or the use of a masking agent such as sodium citrate is necessary. Gold(III) was shown to be effectively back extracted with a 0.1 mol*dm -3 aqueous solution of 2-amino-2-hydroxymethyl-1,3-propanediol. Thus, a radiochemical procedure has been established for preparing a carrier-free multitracer and an Au tracer with carrier form from an Au target irradiated with a heavy-ion beam. Both tracers are now used individually for chemical and biological experiments. (author). 22 refs., 3 figs., 2 tabs

Kinetics of exchange between zero-, one-, and two-hydrogen-bonded states of methyl and ethyl acetate in methanol.

Science.gov (United States)

Chuntonov, Lev; Pazos, Ileana M; Ma, Jianqiang; Gai, Feng

2015-03-26

It has recently been shown that the ester carbonyl stretching vibration can be used as a sensitive probe of local electrostatic field in molecular systems. To further characterize this vibrational probe and extend its potential applications, we studied the kinetics of chemical exchange between differently hydrogen-bonded (H-bonded) ester carbonyl groups of methyl acetate (MA) and ethyl acetate (EA) in methanol. We found that, while both MA and EA can form zero, one, or two H-bonds with the solvent, the population of the 2hb state in MA is significantly smaller than that in EA. Using a combination of linear and nonlinear infrared measurements and numerical simulations, we further determined the rate constants for the exchange between these differently H-bonded states. We found that for MA the chemical exchange reaction between the two dominant states (i.e., 0hb and 1hb states) has a relaxation rate constant of 0.14 ps(-1), whereas for EA the three-state chemical exchange reaction occurs in a predominantly sequential manner with the following relaxation rate constants: 0.11 ps(-1) for exchange between 0hb and 1hb states and 0.12 ps(-1) for exchange between 1hb and 2hb states.

21 CFR 172.515 - Synthetic flavoring substances and adjuvants.

Science.gov (United States)

2010-04-01

.... 3-Octanol. 2-Octanone; methyl hexyl ketone. 3-Octanone; ethyl amyl ketone. 3-Octanon-1-ol. 1-Octen-3...; isodecylaldehyde. 3,7-Dimethyl-1-octanol; tetrahydrogeraniol. α,α-Dimethylphenethyl acetate; benzylpropyl acetate...)-nonanamide; pelargonyl vanillylamide. 5-Hydroxy-4-octanone; butyroin. 4-(p-Hydroxyphenyl)-2-butanone; p-hy...

Emissions and photochemistry of oxygenated VOCs in urban plumes in the Northeastern United States

Directory of Open Access Journals (Sweden)

R. Sommariva

2011-07-01

Full Text Available Photochemical processes inside urban plumes in the Northeast of the United States have been studied using a highly detailed chemical model, based upon the Master Chemical Mechanism (MCM. The model results have been compared to measurements of oxygenated VOCs (acetone, methyl ethyl ketone, acetaldehyde, acetic acid and methanol obtained during several flights of the NOAA WP-3D aircraft, which sampled plumes from the New York City area during the ICARTT campaign in 2004. The agreement between the model and the measurements was within 40–60 % for all species, except acetic acid.

The model results have been used to study the formation and photochemical evolution of acetone, methyl ethyl ketone and acetaldehyde. Under the conditions encountered during the ICARTT campaign, acetone is produced from the oxidation of propane (24–28 % and i-propanol (<15 % and from a number of products of i-pentane oxidation. Methyl ethyl ketone (MEK is mostly produced from the oxidation of n-butane (20–30 % and 3-methylpentane (<40 %. Acetaldehyde is formed from several precursors, mostly small alkenes, >C5 alkanes, propanal and MEK. Ethane and ethanol oxidation account, respectively, for 6–23 % and 5–25 % of acetaldehyde photochemical formation. The results highlight the importance of alkanes for the photochemical production of ketones and the role of hydroperoxides in sustaining their formation far from the emission sources.

Hydrogen Production via Steam Reforming of Ethyl Alcohol over Palladium/Indium Oxide Catalyst

Directory of Open Access Journals (Sweden)

Tetsuo Umegaki

2009-01-01

Full Text Available We report the synergetic effect between palladium and indium oxide on hydrogen production in the steam reforming reaction of ethyl alcohol. The palladium/indium oxide catalyst shows higher hydrogen production rate than indium oxide and palladium. Palladium/indium oxide affords ketonization of ethyl alcohol with negligible by-product carbon monoxide, while indium oxide mainly affords dehydration of ethyl alcohol, and palladium affords decomposition of ethyl alcohol with large amount of by-product carbon monoxide. The catalytic feature of palladium/indium oxide can be ascribed to the formation of palladium-indium intermetallic component during the reaction as confirmed by X-ray diffraction and X-ray photoelectron spectroscopic measurements.

Repurification and characterization of extractant mixture (isobutyl acetate-methyl isobutyl ketone) used in spectrophotometric analytical methods

International Nuclear Information System (INIS)

Al-Merey, R.; Al-Hameish, M.

2001-01-01

Isobutyl acetate (IBA) -methyl isobutyl ketone (MIBK) mixture used in analytical laboratories was re-purified by fractional distillation. The used mixture was washed with 0.5 M Na 2 CO 3 solution for the removal of inorganic substances. The range of fractional distillation was between 111-114 Centigrade which gave an azeotropic mixture that consists of 70% of IBA, 20% of MIBK and 10% of isobutanol (IBL). Gas chromatography (GC) analysis showed that isobutanol was increased by about 10% on the expense of IBA. This study suggests that MIBK could be determined in organic mixture spectrophotometrically. The analytical function of the re-purified mixture is found to be better than the unused mixture. Finally the distillation recovery was 93%. (author)

Effect of ethyl-, methyl- and hydroxyethyl-nitrosourea on the mouse testis

Energy Technology Data Exchange (ETDEWEB)

Oakberg, E.F.; Crosthwait, C.D.

1983-01-01

Hybrid male 101 x C3HF/sub 1/ mice were given intraperitoneal injections of methyl-, ethyl- and hydroxyethyl-nitrosourea and killed 3-16 days later. All compounds were similar in that all differentiating spermatogonia from type A/sub 1/ to early type B were killed by 50 mg/kg and higher doses of ENU and by 75 mg/kg MNU. Cells exposed to leptotene to 100 and 250 mg/kg ENU and 455 mg/kg HENU showed a delayed response with degeneration in pachytene 5 days later. Labeling prior to exposure to ENU indicated that the effect of stage of the mitotic cycle on sensitivity to cell killing is less marked than for radiation. This may be the explanation for the s-shaped mutation induction curve obtained with ENU in contrast to the humped dose-response curve observed for radiation.

Proceedings of Indian Academy of Sciences, Section A- Vol.25

Indian Academy of Sciences (India)

Coumarins from ketonic esters and 5-methyl-2-ethyl, 5-methyl-2-propyl-, ... in presence of anhydrous aluminium chloride — R. D. Desai, M. M. Gaitonde, ... Synthesis of gentisin, the colouring matter of gentian root — Nity Anand and K.

Weathering and chemical degradation of methyl eugenol and raspberry ketone solid dispensers for detection, monitoring and male annihilation of Bactrocera dorsalis and Bactrocera cucurbitae (Diptera: Tephritidae) in Hawaii

Science.gov (United States)

Solid male lure dispensers containing methyl eugenol (ME) and raspberry ketone (RK), or mixtures of the lures (ME + RK), and dimethyl dichloro-vinyl phosphate (DDVP) were evaluated in AWPM bucket or Jackson traps in commercial papaya (Carica papaya L.) orchards where both oriental fruit fly, Bactroc...

Improving methyl ketone production in Escherichia coli by heterologous expression of NADH-dependent FabG

DEFF Research Database (Denmark)

Goh, Ee Been; Chen, Yan; Petzold, Christopher J.

2018-01-01

balance, as fatty acid-derived pathways face the systematic metabolic challenge of net NADPH consumption (in large part, resulting from the key fatty acid biosynthetic enzyme FabG [β-ketoacyl-ACP reductase]) and net NADH production. In this study, we attempted to mitigate cofactor imbalance...... by heterologously expressing NADH-dependent, rather than NADPH-dependent, versions of FabG identified in previous studies. Of the four NADH-dependent versions of FabG tested in our previously best-reported methyl ketone-producing strain (EGS1895), the version from Acholeplasma laidlawii (Al_FabG) showed...... for the base strain (EGS1895) under fermentation conditions optimized in this study. Shotgun proteomic data for strains EGS2920 and EGS1895 during fed-batch fermentation were consistent with the goal of alleviating NADPH limitation through expression of Al_FabG. For example, relative to strain EGS1895, strain...

Kinetic Modelling and Experimental Study of Small Esters: Methyl Acetate and Ethyl Acetate

KAUST Repository

Ahmed, Ahfaz; Mehl, Marco; Lokachari, Nitin; Nilsson, Elna J.K.; Konnov, Alexander A.; Wagnon, Scott W.; Pitz, William J.; Curran, Henry J.; Roberts, William L.; Sarathy, Mani

2017-01-01

A detailed chemical kinetic mechanism comprising methyl acetate and ethyl acetate has been developed based on the previous work by Westbrook et al. [1]. The newly developed kinetic mechanism has been updated with new reaction rates from recent theoretical studies. To validate this model, shock tube experiments measuring ignition delay time have been conducted at 15 & 30 bar and equivalence ratio 0.5, 1.0 and 2.0. Another set of experiments measuring laminar burning velocity was also performed on a heat flux burner at atmospheric pressure over wide range of equivalence ratios [~0.7-1.4]. The new mechanism shows significant improvement in prediction of experimental data over earlier model across the range of experiments.

Kinetic Modelling and Experimental Study of Small Esters: Methyl Acetate and Ethyl Acetate

KAUST Repository

Ahmed, Ahfaz

2017-12-14

A detailed chemical kinetic mechanism comprising methyl acetate and ethyl acetate has been developed based on the previous work by Westbrook et al. [1]. The newly developed kinetic mechanism has been updated with new reaction rates from recent theoretical studies. To validate this model, shock tube experiments measuring ignition delay time have been conducted at 15 & 30 bar and equivalence ratio 0.5, 1.0 and 2.0. Another set of experiments measuring laminar burning velocity was also performed on a heat flux burner at atmospheric pressure over wide range of equivalence ratios [~0.7-1.4]. The new mechanism shows significant improvement in prediction of experimental data over earlier model across the range of experiments.

Effluents from MBT plants: Plasma techniques for the treatment of VOCs

Energy Technology Data Exchange (ETDEWEB)

Ragazzi, Marco, E-mail: marco.ragazzi@unitn.it [Department of Civil, Environmental and Mechanical Engineering, University of Trento, Via Mesiano 77, I-38123 Trento (Italy); Tosi, Paolo, E-mail: paolo.tosi@unitn.it [Department of Physics, University of Trento, Via Sommarive 5, I-38123 Trento (Italy); Rada, Elena Cristina, E-mail: elena.rada@unitn.it [Department of Civil, Environmental and Mechanical Engineering, University of Trento, Via Mesiano 77, I-38123 Trento (Italy); Torretta, Vincenzo, E-mail: vincenzo.torretta@uninsubria.it [Department of Biotechnologies and Life Sciences, University of Insubria, Via G.B. Vico 46, I-21100 Varese (Italy); Schiavon, Marco, E-mail: marco.schiavon@unitn.it [Department of Civil, Environmental and Mechanical Engineering, University of Trento, Via Mesiano 77, I-38123 Trento (Italy); Department of Biotechnologies and Life Sciences, University of Insubria, Via G.B. Vico 46, I-21100 Varese (Italy)

2014-11-15

Highlights: • Dielectric Barrier Discharge was applied to remove methyl ethyl ketone from air. • Methyl ethyl ketone was chosen since it represents emissions from MBT plants. • The removal efficiency was linearly dependent on time, power and energy density. • Besides CO{sub 2}, methyl nitrate and 2,3-butanedione were the main byproducts formed. • The removal efficiency can be increased by increasing the convective flow. - Abstract: Mechanical–biological treatments (MBTs) of urban waste are growing in popularity in many European countries. Recent studies pointed out that their contribution in terms of volatile organic compounds (VOCs) and other air pollutants is not negligible. Compared to classical removal technologies, non-thermal plasmas (NTP) showed better performances and low energy consumption when applied to treat lowly concentrated streams. Therefore, to study the feasibility of the application of NTP to MBTs, a Dielectric Barrier Discharge reactor was applied to treat a mixture of air and methyl ethyl ketone (MEK), to simulate emissions from MBTs. The removal efficiency of MEK was linearly dependent upon time, power and specific input energy. Only 2–4% of MEK was converted to carbon dioxide (CO{sub 2}), the remaining carbon being involved in the formation of byproducts (methyl nitrate and 2,3-butanedione, especially). For future development of pilot-scale reactors, acting on residence time, power, convective flow and catalysts will help finding a compromise between energy consumption, desired abatement and selectivity to CO{sub 2}.

Experimental and Kinetic Modeling Study of Ethyl Levulinate Oxidation in a Jet-Stirred Reactor

KAUST Repository

Wang, Jui-Yang

2017-06-01

A jet-stirred reactor was designed and constructed in the Clean Combustion Research Center (CCRC) at King Abdullah University of Science and Technology (KAUST); was validated with n-heptane, iso-octane oxidation and cyclohexene pyrolysis. Different configurations of the setup have been tested to achieve good agreement with results from the literature. Test results of the reactor indicated that installation of a pumping system at the downstream side in the experimental apparatus was necessary to avoid the reoccurrence of reactions in the sampling probe. Experiments in ethyl levulinate oxidation were conducted in the reactor under several equivalence ratios, from 600 to 1000 K, 1 bar and 2 s residence time. Oxygenated species detected included methyl vinyl ketone, levulinic acid and ethyl acrylate. Ethylene, methane, carbon monoxide, hydrogen, oxygen and carbon dioxide were further quantified with a gas chromatography, coupled with a flame ionization detector and a thermal conductivity detector. The ethyl levulinate chemical kinetic model was first developed by Dr. Stephen Dooley, Trinity College Dublin, and simulated under the same conditions, using the Perfect-Stirred Reactor code in Chemkin software. In comparing the simulation results with experimental data, some discrepancies were noted; predictions of ethylene production were not well matched. The kinetic model was improved by updating several classes of reactions: unimolecular decomposition, H-abstraction, C-C and C-O beta-scissions of fuel radicals. The updated model was then compared again with experimental results and good agreement was achieved, proving that the concerted eliminated reaction is crucial for the kinetic mechanism formulation of ethyl levulinate. In addition, primary reaction pathways and sensitivity analysis were performed to describe the role of molecular structure in combustion (800 and 1000 K for ethyl levulinate oxidation in the jet-stirred reactor).

Crystal structure of (Z-ethyl 3-[2-(5-methyl-7-nitro-1H-indole-2-carbonylhydrazinylidene]butanoate

Directory of Open Access Journals (Sweden)

Amal Errossafi

2015-09-01

Full Text Available The reaction of 5-methyl-7-nitro-1H-indole-2-carbohydrazide with ethyl acetoacetate yielded the title molecule, C16H18N4O5, in which the indole ring is almost planar, with the greatest deviation from the mean plane being 0.006 (2 Å. The nine atoms of the indole ring are almost perpendicular to the mean plane through the ethyl acetate group, as indicated by the dihedral angle of 87.02 (4° between them. In the crystal, centrosymmetric supramolecular dimers are formed via N—H...O hydrogen bonds and eight-membered amide {...HNCO}2 synthons. These are consolidated into a three-dimensional architecture by C—H...O contacts, and by π–π interactions between six-membered rings [inter-centroid distance = 3.499 (2 Å].

Contribution to the study of the structure and reactivity of ketones using deuterium substitution of the α - ketone hydrogens

International Nuclear Information System (INIS)

Frejaville, G.

1966-02-01

This work is an attempt to obtain more knowledge about the structure and the reactivity of ketones; it is also a contribution to conformational analysis based on infrared signals associated with the C-D vibration in mono-deuterated compounds. In the first chapter the various dosage and synthetic methods used in this work are described. In the second chapter the infrared spectra in the 2100-2200 cm -1 region for mono-deuterated ketones are interpreted on the basis of a simple model. This model is then studied in detail, and also critically and precisely, in the case of the mono deuterated acetone molecule. In the third chapter is studied the mechanism of the Favorskii reaction and the reactivity of all the α-ketonic hydrogens of 2 chloro-cyclohexanone are classified. In a technical appendix is described a counter-current exchange method for obtaining a great variety of solvents and deuterated pure raw materials under advantageous conditions. (author) [fr

Phosphine-catalyzed cycloadditions of allenic ketones: new substrates for nucleophilic catalysis.

Science.gov (United States)

Wallace, Debra J; Sidda, Rachel L; Reamer, Robert A

2007-02-02

A range of phosphine-catalyzed cycloaddition reactions of allenic ketones have been studied, extending the scope of these processes from the more widely used 2,3-butadienoates to allow access to a number of synthetically useful products. Reaction of allenyl methyl ketone 4 with exo-enones afforded spirocyclic compounds in good regioselectivity and promising enantioselectivity via a [2 + 3] cycloaddtion. Aromatic allenyl ketones undergo a phosphine-promoted dimerization to afford functionalized pyrans, leading to a formal [2 + 4] Diels-Alder product, but did not react in the [2 + 3] cycloaddition. The results from other reactions that had found utility with 2,3-butadienoates are also reported.

Asymmetric Chemoenzymatic Reductive Acylation of Ketones by a Combined Iron-Catalyzed Hydrogenation-Racemization and Enzymatic Resolution Cascade

KAUST Repository

El-Sepelgy, Osama

2017-02-28

A general and practical process for the conversion of prochiral ketones into the corresponding chiral acetates has been realized. An iron carbonyl complex is reported to catalyze the hydrogenation-dehydrogenation-hydrogenation of prochiral ketones. By merging the iron-catalyzed redox reactions with enantioselective enzymatic acylations a wide range of benzylic, aliphatic and (hetero)aromatic ketones, as well as diketones, were reductively acylated. The corresponding products were isolated with high yields and enantioselectivities. The use of an iron catalyst together with molecular hydrogen as the hydrogen donor and readily available ethyl acetate as acyl donor make this cascade process highly interesting in terms of both economic value and environmental credentials.

TRANSPORT PROPERTIES FOR 1-ETHYL-3-METHYLIMIDAZOLIUM n-ALKYL SULFATES: POSSIBLE EVIDENCE OF GROTTHUSS MECHANISM

International Nuclear Information System (INIS)

García-Garabal, S.; Vila, J.; Rilo, E.; Domínguez-Pérez, M.; Segade, L.; Tojo, E.; Verdía, P.; Varela, L.M.; Cabeza, O.

2017-01-01

The objective of this work was to study the effect of the temperature and the lengthening of the linear alkyl chain of the anion in the transport physical properties of the pure ionic liquids 1-ethyl-3-methyl imidazolium n-alkyl sulphate (being n = 0, 1, 2, 4, 6 and 8). Density, viscosity and electrical conductivities were measured at atmospheric pressure in a wide temperature range. In the bibliography, data existed for these magnitudes for all ionic liquids studied but none of these had information about the electrical conductivity of 1-ethyl-3-methyl imidazolium n-alkyl sulfate whith n = 0, 4, 6 and 8. The experimental results show clearly 1-ethyl-3-methyl imidazolium hydrogen sulphate cannot be considered part of the 1-ethyl-3-methyl imidazolium n-alkyl sulphate family because of its hydrogen bonding ability. Results of density and viscosity behave as expected. However, in the case of the electrical conductivity due to the lack of alkyl chain in the hydrogen sulfate we expected to get extreme values but in practise, we obtained intermediate values between 1-ethyl-3-methyl imidazolium butyl sulphate and 1-ethyl-3-methyl imidazolium hexyl sulphate. This suggests that a Grotthus mechanism exists as result of a protonic current in addition to ionic conductivity, being Waldeńs plot consistent with this idea.

Temperature Induced Solubility Transitions of Various Poly(2-oxazolines in Ethanol-Water Solvent Mixtures

Directory of Open Access Journals (Sweden)

Hanneke M. L. Lambermont-Thijs

2010-08-01

Full Text Available The solution behavior of a series of poly(2-oxazolines with different side chains, namely methyl, ethyl, n-propyl, isopropyl, n-butyl, isobutyl, pentyl, hexyl, heptyl, octyl, nonyl, phenyl and benzyl, are reported in ethanol-water solvent mixtures based on turbidimetry investigations. The LCST transitions of poly(2-oxazolines with propyl side chains and the UCST transitions of the poly(2-oxazolines with more hydrophobic side chains are discussed in relation to the ethanol-water solvent composition and structure. The poly(2-alkyl-2-oxazolines with side chains longer than propyl only dissolved during the first heating run, which is discussed and correlated to the melting transition of the polymers.

Distribution of methyl and ethyl adducts following alkylation with monofunctional alkylating agents.

Science.gov (United States)

Beranek, D T

1990-07-01

Alkylating agents, because of their ability to react directly with DNA either in vitro or in vivo, or following metabolic activation as in the case of the dialkylnitrosamines, have been used extensively in studying the mechanisms of mutagenicity and carcinogenicity. Their occurrence is widespread in the environment and human exposure from natural and pollutant sources is universal. Since most of these chemicals show varying degrees of both carcinogenicity and mutagenicity, and exhibit compound-specific binding patterns, they provide an excellent model for studying molecular dosimetry. Molecular dosimetry defines dose as the number of adducts bound per macromolecule and relates the binding of these adducts to the human mutagenic or carcinogenic response. This review complies DNA alkylation data for both methylating and ethylating agents in a variety of systems and discusses the role these alkylation products plays in molecular mutagenesis.

Assessment of control strategies for reducing volatile organic compound emissions from the polyvinyl chloride wallpaper production industry in Taiwan.

Science.gov (United States)

Chang, Chang-Tang; Chiou, Chyow-Shan

2006-05-01

This study attempts to assess the effectiveness of control strategies for reducing volatile organic compound (VOC) emission from the polyvinyl chloride (PVC) wallpaper production industry. In Taiwan, methyl ethyl ketone, TOL, and cyclohexanone have comprised the major content of solvents, accounting for approximately 113,000 t/yr to avoid excessive viscosity of plasticizer dioctyl phthalate (DOP) and to increase facility in working. Emissions of these VOCs from solvents have caused serious odor and worse air quality problems. In this study, 80 stacks in five factories were tested to evaluate emission characteristics at each VOC source. After examining the VOC concentrations in the flue gases and contents, the VOC emission rate before treatment and from fugitive sources was 93,000 and 800 t/yr, respectively. In this study, the semiwet electrostatic precipitator is recommended for use as cost-effective control equipment.

Presence and potential significance of aromatic-ketone groups in aquatic humic substances

Science.gov (United States)

Leenheer, J.A.; Wilson, M.A.; Malcolm, R.L.

1987-01-01

Aquatic humic- and fulvic-acid standards of the International Humic Substances Society were characterized, with emphasis on carbonyl-group nature and content, by carbon-13 nuclear-magnetic-resonance spectroscopy, proton nuclear-magnetic-resonance spectroscopy, and infrared spectroscopy. After comparing spectral results of underivatized humic and fulvic acids with spectral results of chemically modified derivatives, that allow improved observation of the carbonyl group, the data clearly indicated that aromatic ketone groups comprised the majority of the carbonyl-group content. About one ketone group per monocyclic aromatic ring was determined for both humic and fulvic acids. Aromatic-ketone groups were hypothesized to form by photolytic rearrangements and oxidation of phenolic ester and hydrocarbon precursors; these groups have potential significance regarding haloform formation in water, reactivity resulting from active hydrogen of the methyl and methylene adjacent to the ketone groups, and formation of hemiketal and lactol structures. Aromatic-ketone groups also may be the point of attachment between aliphatic and aromatic moieties of aquatic humic-substance structure. ?? 1987.

Efficacy of scalp hair decontamination following exposure to vapours of sulphur mustard simulants 2-chloroethyl ethyl sulphide and methyl salicylate

OpenAIRE

Spiandore , Marie; Piram , Anne; Lacoste , Alexandre; Prevost , P.; Maloni , Pascal; TORRE , Franck; Asia , L.; Josse , D.; Doumenq , Pierre

2017-01-01

International audience; Chemical warfare agents are an actual threat and victims' decontamination is a main concern when mass exposure occurs. Skin decontamination with current protocols has been widely documented, as well as surface decontamination. However, considering hair ability to trap chemicals in vapour phase, we investigated hair decontamination after exposure to sulphur mustard simulants methyl salicylate and 2-chloroethyl ethyl sulphide. Four decontamination protocols were tested o...

Synthesis of quinoxaline 1,4-di-n-oxide derivatives on solid support using room temperature and microwave-assisted solvent-free procedures

International Nuclear Information System (INIS)

Gomez-Caro, Lilia C.; Sanchez-Sanchez, Mario; Bocanegra-Garcia, Virgilio; Rivera, Gildardo; Monge, Antonio

2011-01-01

We describe the synthesis of 12 new ethyl and methyl quinoxaline-7-carboxylate 1,4-di-N-oxide derivatives on solid supports with room temperature and microwave-assisted solvent-free procedures. Results show that solid supports have good catalytic activity in the formation of quinoxaline 1,4-di-N-oxide derivatives. We found that florisil and montmorillonite KSF and K10 could be used as new, easily available, inexpensive alternatives of catalysts. Additionally, room temperature and microwave-irradiation solvent-free synthesis was more efficient than a conventional procedure (Beirut reaction), reducing reaction time and increasing yield. (author)

Synthesis of quinoxaline 1,4-di-n-oxide derivatives on solid support using room temperature and microwave-assisted solvent-free procedures

Energy Technology Data Exchange (ETDEWEB)

Gomez-Caro, Lilia C.; Sanchez-Sanchez, Mario; Bocanegra-Garcia, Virgilio; Rivera, Gildardo [Universidad Autonoma de Tamaulipas, Reynosa (Mexico). Dept. de Farmacia y Quimica Medicinal; Monge, Antonio [Universidad de Navarra, Pamplona (Spain). Centro de Investigacion en Farmacobiologia Aplicada. Unidad de Investigacion y Desarrollo de Medicamentos

2011-07-01

We describe the synthesis of 12 new ethyl and methyl quinoxaline-7-carboxylate 1,4-di-N-oxide derivatives on solid supports with room temperature and microwave-assisted solvent-free procedures. Results show that solid supports have good catalytic activity in the formation of quinoxaline 1,4-di-N-oxide derivatives. We found that florisil and montmorillonite KSF and K10 could be used as new, easily available, inexpensive alternatives of catalysts. Additionally, room temperature and microwave-irradiation solvent-free synthesis was more efficient than a conventional procedure (Beirut reaction), reducing reaction time and increasing yield. (author)

Fragrance material review on cyclohexyl methyl pentanone.

Science.gov (United States)

Scognamiglio, J; Letizia, C S; Api, A M

2013-12-01

A toxicologic and dermatologic review of cyclohexyl methyl pentanone when used as a fragrance ingredient is presented. Cyclohexyl methyl pentanone is a member of the fragrance structural group Alkyl Cyclic Ketones. These fragrances can be described as being composed of an alkyl, R1, and various substituted and bicyclic saturated or unsaturated cyclic hydrocarbons, R2, in which one of the rings may include up to 12 carbons. Alternatively, R2 may be a carbon bridge of C2-C4 carbon chain length between the ketone and cyclic hydrocarbon. This review contains a detailed summary of all available toxicology and dermatology papers that are related to this individual fragrance ingredient and is not intended as a stand-alone document. Available data for cyclohexyl methyl pentanone were evaluated then summarized and includes physical properties, acute toxicity, skin irritation, mucous membrane (eye) irritation, skin sensitization, phototoxicity, photoallergy, and genotoxicity data. A safety assessment of the entire Alkyl Cyclic Ketones will be published simultaneously with this document; please refer to Belsito et al. (Belsito, D., Bickers, D., Bruze, M., Calow, P., Dagli, M., Fryer, A.D., Greim, H., Miyachi, Y., Saurat, J.H., Sipes, I.G., 2013. A toxicologic and dermatologic assessment of alkyl cyclic ketones when used as fragrance ingredients (submitted for publication).) for an overall assessment of the safe use of this material and all Alkyl Cyclic Ketones in fragrances. Copyright © 2013. Published by Elsevier Ltd.

Removal and Recovery of Organic Vapor Emissions by Fixed-Bed Activated Carbon Fiber Adsorber-Cryogenic Condenser

National Research Council Canada - National Science Library

Hay, K

1998-01-01

... them. This project evaluated the ability of an activated carbon fiber cloth (ACFC) adsorption, electrothermal desorption, cryogenic-condensation system to remove 10 cu cm/min containing 1000 ppmv of methyl ethyl ketone (MEK...

Biofiltration of paint solvent mixtures in two reactor types: overloading by hydrophobic components.

Science.gov (United States)

Paca, Jan; Halecky, Martin; Misiaczek, Ondrej; Jones, Kim; Kozliak, Evguenii; Sobotka, Miroslav

2010-12-01

Steady-state performance characteristics of a trickle bed reactor (TBR) and a biofilter (BF) in loading experiments with increasing toluene/xylenes inlet concentrations while maintaining a constant loading rate of hydrophilic components (methyl ethyl and methyl isobutyl ketones, acetone, and n-butyl acetate) of 4 g m⁻³ h⁻¹ were evaluated and compared, along with the systems' dynamic responses. At the same combined substrate loading of 55 g m⁻³ h⁻¹ for both reactors, the TBR achieved more than 1.5 times higher overall removal efficiency (RE(W)) than the BF. Increasing the loading rate of aromatics resulted in a gradual decrease of their REs. The degradation rates of acetone and n-butyl acetate were also inhibited at higher loads of aromatics, thus revealing a competition in cell catabolism. A step-drop in loading of aromatics resulted in an immediate increase of RE(W) with variations in the TBR, while the new steady-state value in the BF took 6-7 h to achieve. The TBR consistently showed a greater performance than BF in removing toluene and xylenes. Increasing the loading rate of aromatics resulted in a gradual decrease of their REs. The degradation rates of acetone and n-butyl acetate were also lower at higher OL(AROM), revealing a competition in the cell catabolism. The results obtained are consistent with the proposed hypothesis of greater toxic effects under low water content, i.e., in the biofilter, caused by aromatic hydrocarbons in the presence of polar ketones and esters, which may improve the hydrocarbon partitioning into the aqueous phase.

Synthesis, characterization and catalytic performance of mixed nanoferrites submitted to transesterification and esterification reaction using methyl and ethyl route for biodiesel production

International Nuclear Information System (INIS)

Dantas, Joelda; Leal, Elvia; Mapossa, Antonio Benjamim; Silva, Adriano Sant'Ana; Costa, Ana Cristina Figueiredo de Melo

2016-01-01

The mixed nanoferrites of Ni_0_._5Zn_0_._5Fe_2O_4 and Ni_0_._2Cu_0_._3Zn_0_._5Fe_2O_4 were synthesized by combustion reaction using urea as fuel and a conical reactor as heating source in batches of 10 g, and then tested as heterogeneous nanocatalysts in the transesterification and esterification reaction of soya bean oil using the methyl and ethyl routes to biodiesel production. During the synthesis the time and temperature of the reactions were measured, and the evolved gases and the color of the emitted flames were observed. The samples were characterized by XRD, EDX, FTIR, SEM/EDS, BET and gas chromatography. The reaction tests were carried out with 10 g of oil for 1 h, oil:alcohol molar ratio of 1:12, 2 % (w/w) of catalyst, and conducted at 180 °C. The XRD patterns and the FTIR spectra revealed the presence of the inverse spinel phase type B(AB)_2O_4. The morphology showed the formation of agglomerates with fragile morphology and high surface area. The chromatographic analysis produced excellent results in the esterification reactions for both samples in the tested conditions, with special emphasis on Ni_0_._5Zn_0_._5Fe_2O_4, whose conversions were of 91.4 % in methyl esters and of 77.8 % in ethyl esters, while the Ni_0_._2Cu_0_._3Zn_0_._5Fe_2O_4 sample showed conversion of 75.1 and 65.1 %, respectively. The conversions in the methyl and ethyl transesterification were of 14 and 2 % of the Ni_0_._5Zn_0_._5Fe_2O_4 sample, and of 11 and 3 % for the Ni_0_._2Cu_0_._3Zn_0_._5Fe_2O_4 sample. (author)

Phase equilibria and the thermodynamic properties of methyl and ethyl esters of carboxylic acids. 1. Methyl n-butanoate and ethyl propanoate

International Nuclear Information System (INIS)

Agafonova, Luba E.; Varushchenko, Raisa M.; Druzhinina, Anna I.; Polyakova, Olga V.

2012-01-01

Highlights: ► Heat capacities, fusion properties of CH 3 OC(O)C 3 H 7 measured by adiabatic calorimetry. ► The temperature dependence of vapour pressure determined by comparative ebulliometry. ► The thermodynamic functions derived from experiment and calculated by DFT method. ► Extending vapour pressure of moderate interval to entire region of liquid. ► An increment of the entropy of carbonyl group was defined from experimental data. - Abstract: The heat capacity of methyl n-butanoate in crystalline and liquid states was measured by vacuum adiabatic calorimetry over the temperature range from (8 to 372) K. The triple point temperature, the enthalpy and entropy of fusion, and the purity of the sample were determined. The saturated vapour pressure and the boiling temperatures were determined by comparative ebulliometry in the “atmospheric” pressure range 10.8 ⩽ (p/kPa) ⩽ 99.6. The normal boiling temperature, T n.b , and the enthalpy of vaporization at T = 298.15 K and T n.b were derived. The thermodynamic functions (absolute entropy and changes of the enthalpy, and Gibbs free energy) were derived for the solid and liquid states in the temperature range studied and for the ideal gas state at T = 298.15 K. The ideal gas heat capacities and the absolute entropies of methyl n-butanoate (MeBu) and ethyl propanoate (EtPr) were calculated by statistical thermodynamics on the basis of the molecular constants determined by the use of density functional theory on the B3LYP level. The experimental vapour pressure of MeBu and EtPr of moderate temperature intervals, Δ exp T = (59/65) K, were extended to the entire range of the liquids, Δ liq T = (364.7/345.7) K by the methods of the corresponding states law and simultaneous treatment of the pT-parameters and low-temperature heat capacities of the ideal gas and liquid, respectively. An additive contribution of the carbonyl group CO–(C, O) connected with C and O atoms was determined for calculation of the

Sensibilidade do carrapato Boophilus microplus a solventes Sensibility of Boophilus microplus tick to solvents

Directory of Open Access Journals (Sweden)

Ana Carolina de Souza Chagas

2003-02-01

Full Text Available Os experimentos envolvendo o uso de acaricidas sintéticos ou naturais, geralmente necessitam da utilização de um solvente. Com a finalidade de verificar a sensibilidade do carrapato bovino Boophilus microplus a diferentes solventes, larvas e fêmeas ingurgitadas deste ectoparasito foram expostas a sete solventes em cinco diferentes concentrações, na ausência e presença de azeite de oliva. Os resultados mostraram que a utilização do azeite de oliva não produz resultados diferentes estatisticamente em testes de larvas com papel impregnado, fato não verificado em testes de imersão de adultos com compostos hidrofílicos. A mortalidade média causada pelos solventes foi menor nos testes com papel impregnado, aumentando nos testes de imersão de larvas e de adultos. Solventes de baixo peso molecular e pouca viscosidade como o álcool metílico e o álcool etílico, não interferiram na mortalidade média em testes biológicos de B. microplus, principalmente em concentrações inferiores a 76%.Experiments carried out with synthetic or natural acaricides usually use a solvent. To investigate the sensitivity of Boophilus microplus cattle tick to different solvents, larvae and engorged female were subjected to seven solvents in five different concentrations. It was done in the presence and absence of olive oil. The results showed that the utilization of olive oil doesn't produce different statistical results in impregnated paper larvae test. It did not happen in adults immersion test with hydrophilic compounds. The mean mortality caused by solvents was small in impregnated paper larvae test, increasing in immersion tests of larvae and adults. Solvents with low molecular weight and viscosity like ethyl alcohol and methyl alcohol did not cause interference in the mortality of B. microplus in biological tests, mainly in concentrations below 76%.

Biodegradation of volatile organic compounds by five fungal species

Energy Technology Data Exchange (ETDEWEB)

Qi, B.; Moe, W.M. [Dept. of Civil and Environmental Engineering, Louisiana State Univ., Baton Rouge, LA (United States); Kinney, K.A. [Dept. of Civil Engineering, Univ. of Texas, Austin (United States)

2002-07-01

Five fungal species, Cladosporium resinae (ATCC 34066), Cladosporium sphaerospermum (ATCC 200384), Exophiala lecanii-corni (CBS 102400), Mucor rouxii (ATCC 44260), and Phanerochaete chrysosporium (ATCC 24725), were tested for their ability to degrade nine compounds commonly found in industrial off-gas emissions. Fungal cultures inoculated on ceramic support media were provided with volatile organic compounds (VOCs) via the vapor phase as their sole carbon and energy sources. Compounds tested included aromatic hydrocarbons (benzene, ethylbenzene, toluene, and styrene), ketones (methyl ethyl ketone, methyl isobutyl ketone, and methyl propyl ketone), and organic acids (n-butyl acetate, ethyl 3-ethoxypropionate). Experiments were conducted using three pH values ranging from 3.5 to 6.5. Fungal ability to degrade each VOC was determined by observing the presence or absence of visible growth on the ceramic support medium during a 30-day test period. Results indicate that E. lecanii-corni and C. sphaerospermum can readily utilize each of the nine VOCs as a sole carbon and energy source. P. chrysosporium was able to degrade all VOCs tested except for styrene under the conditions imposed. C. resinae was able to degrade both organic acids, all of the ketones, and some of the aromatic compounds (ethylbenzene and toluene); however, it was not able to grow utilizing benzene or styrene under the conditions tested. With the VOCs tested, M. rouxii produced visible growth only when supplied with n-butyl acetate or ethyl 3-ethoxypropionate. Maximum growth for most fungi was observed at a pH of approximately 5.0. The experimental protocol utilized in these studies is a useful tool for assessing the ability of different fungal species to degrade gas-phase VOCs under conditions expected in a biofilter application. (orig.)

Ketones urine test

Science.gov (United States)

Ketone bodies - urine; Urine ketones; Ketoacidosis - urine ketones test; Diabetic ketoacidosis - urine ketones test ... Urine ketones are usually measured as a "spot test." This is available in a test kit that ...

Synthesis of All-Z-1,6,9,12,15-Octadecapenten-3-one, A Vinyl Ketone Polyunsaturated Marine Natural Product Isolated from Callysponga sp.

Directory of Open Access Journals (Sweden)

Anne Marie Langseter

2014-03-01

Full Text Available The synthesis of the marine natural product 1,6Z,9Z,12Z,15Z-octadecapentaen-3-one (1 has been achieved by two different routes starting from the ethyl esters of eicosapentaenoic acid (EPA and docosahexaenoic acid (DHA, respectively. Using EPA ethyl ester as starting material the polyunsaturated vinyl ketone lipid 1 was obtained in 17% overall yield.

Structural study of ethyl 3-methyl-9-oxo-3-azabicyclo63.3.19nonane-1-carboxylate by two-dimensional NMR spectroscopy

Science.gov (United States)

Arias-Pérez, M. S.; Alejo, A.; Gálvez, E.; Pérez, S. M.; Santos, M. J.

1995-04-01

Ethyl 3-methyl-9-oxo-3-azabicyclo[3.3.1]nonane-1-carboxylate has been studied by 1H, 13C and 2D NMR spectroscopy in order to establish its conformational behaviour. The combined use of COSY and 1H- 13C correlation spectra helped in the unambiguous and complete assignment of the bicyclic carbon and proton resonances. It is found that the piperidone ring displays a slightly fattened chair conformation with the N-methyl group in the equatorial position, while a twist-chair form seems to be favoured for the cyclohexanone one. Two preferred orientations migth be proposed for the ethoxycarbonyl moiety.

Chemo-Enzymatic Synthesis of Chiral Epoxides Ethyl and Methyl (S-3-(Oxiran-2-ylpropanoates from Renewable Levoglucosenone: An Access to Enantiopure (S-Dairy Lactone

Directory of Open Access Journals (Sweden)

Aurélien A. M. Peru

2016-07-01

Full Text Available Chiral epoxides—such as ethyl and methyl (S-3-(oxiran-2-ylpropanoates ((S-1a/1b—are valuable precursors in many chemical syntheses. Until recently, these compounds were synthesized from glutamic acid in four steps (deamination, reduction, tosylation and epoxide formation in low to moderate overall yield (20%–50%. Moreover, this procedure requires some harmful reagents such as sodium nitrite ((ecotoxic and borane (carcinogen. Herein, starting from levoglucosenone (LGO, a biobased chiral compound obtained through the flash pyrolysis of acidified cellulose, we propose a safer and more sustainable chemo-enzymatic synthetic pathway involving lipase-mediated Baeyer-Villiger oxidation, palladium-catalyzed hydrogenation, tosylation and treatment with sodium ethoxide/methoxide as key steps. This route afforded ethyl and methyl (S-3-(oxiran-2-ylpropanoates in 57% overall yield, respectively. To demonstrate the potentiality of this new synthetic pathway from LGO, the synthesis of high value-added (S-dairy lactone was undertaken from these epoxides and provided the target in 37% overall yield from LGO.

Deuterium labelling of tryptamine, serotonin and their N-methylated metabolites using solvent exchange reactions

Energy Technology Data Exchange (ETDEWEB)

Raeisaenen, M; Kaerkkaeinen, J [Helsinki Univ. (Finland). Dept. of Medical Chemistry

1979-01-01

Technically uncomplicated methods based on catalytic isotope exchange in deuterated solvents are described for the deuteration of tryptamine, serotonin and their N-methylated metabolites. Heterogeneous platinum catalysis, homogeneous acid catalysis and their combination have been employed. The properties of the labelled derivatives prepared with each technique as well as their use in mass spectrometric work are discussed.

Deuterium labelling of tryptamine, serotonin and their N-methylated metabolites using solvent exchange reactions

International Nuclear Information System (INIS)

Raeisaenen, M.; Kaerkkaeinen, J.

1979-01-01

Technically uncomplicated methods based on catalytic isotope exchange in deuterated solvents are described for the deuteration of tryptamine, serotonin and their N-methylated metabolites. Heterogeneous platinum catalysis, homogeneous acid catalysis and their combination have been employed. The properties of the labelled derivatives prepared with each technique as well as their use in mass spectrometric work are discussed. (author)

ESR, electrochemical and cyclodextrin-inclusion studies of triazolopyridyl pyridyl ketones and dipyridyl ketones derivatives

Science.gov (United States)

Olea-Azar, C.; Abarca, B.; Norambuena, E.; Opazo, L.; Jullian, C.; Valencia, S.; Ballesteros, R.; Chadlaoui, M.

2008-11-01

The electron spin resonance (ESR) spectra of free radicals obtained by electrolytic reduction of triazolopyridyl pyridyl ketones and dipyridyl ketones derivatives were measured in dimethylsulfoxide (DMSO). The hyperfine patterns indicate that the spin density delocalization is dependent of the rings presented in the molecule. The electrochemistry of these compounds was characterized using cyclic voltammetry, in DMSO as solvent. When one carbonyl is present in the molecule one step in the reduction mechanism was observed while two carbonyl are present two steps were detected. The first wave was assigned to the generation of the correspondent free radical species, and the second wave was assigned to the dianion derivatives. The phase-solubility measurements indicated an interaction between molecules selected and cyclodextrins in water. These inclusion complexes are 1:1 with βCD, and HP-βCD. The values of Ks showed a different kind of complexes depending on which rings are included. AM1 and DFT calculations were performed to obtain the optimized geometries, theoretical hyperfine constants, and spin distributions, respectively. The theoretical results are in complete agreement with the experimental ones.

Microporous polyurethane-acrylamide film cured by electron beam irradiation

International Nuclear Information System (INIS)

Ando, Masayuki; Goto, Takakazu; Tsuchiya, Mitsuru; Uryu, Toshiyuki

1988-01-01

The morphology and aggregation structure of electron beam (EB)-cured microporous polyurethane-acrylamide film was investigated. The urethane-acrylamide prepolymer was synthesized by the reaction of poly(butylene adipate)diol, diphenylmethane diisocyanate, and N-(hydroxymethyl)acrylamide. It was found from scanning electron microscopy that the urethane-acrylamide film, which was prepared by using a methyl ethyl ketone and dimethylformamide (3:1 v/v) mixture as casting solvent, had a microporous structure with pore size of several micrometers, and that the morphology was fixed by EB irradiation. The pore volume of the EB-cured microporous film was determined to be about 460 mm 3 g -1 by mercury porosimetry. The micropores were not destroyed even after immersing in solvent, possibly because the cured film had high crystallinity and dense crosslinking. Moreover, it was found by X-ray photelectron spectroscopy that terminal portions of urethane-acrylamide were localized at the film surface. (author)

Absolute photoionization cross-section of the methyl radical.

Science.gov (United States)

Taatjes, Craig A; Osborn, David L; Selby, Talitha M; Meloni, Giovanni; Fan, Haiyan; Pratt, Stephen T

2008-10-02

The absolute photoionization cross-section of the methyl radical has been measured using two completely independent methods. The CH3 photoionization cross-section was determined relative to that of acetone and methyl vinyl ketone at photon energies of 10.2 and 11.0 eV by using a pulsed laser-photolysis/time-resolved synchrotron photoionization mass spectrometry method. The time-resolved depletion of the acetone or methyl vinyl ketone precursor and the production of methyl radicals following 193 nm photolysis are monitored simultaneously by using time-resolved synchrotron photoionization mass spectrometry. Comparison of the initial methyl signal with the decrease in precursor signal, in combination with previously measured absolute photoionization cross-sections of the precursors, yields the absolute photoionization cross-section of the methyl radical; sigma(CH3)(10.2 eV) = (5.7 +/- 0.9) x 10(-18) cm(2) and sigma(CH3)(11.0 eV) = (6.0 +/- 2.0) x 10(-18) cm(2). The photoionization cross-section for vinyl radical determined by photolysis of methyl vinyl ketone is in good agreement with previous measurements. The methyl radical photoionization cross-section was also independently measured relative to that of the iodine atom by comparison of ionization signals from CH3 and I fragments following 266 nm photolysis of methyl iodide in a molecular-beam ion-imaging apparatus. These measurements gave a cross-section of (5.4 +/- 2.0) x 10(-18) cm(2) at 10.460 eV, (5.5 +/- 2.0) x 10(-18) cm(2) at 10.466 eV, and (4.9 +/- 2.0) x 10(-18) cm(2) at 10.471 eV. The measurements allow relative photoionization efficiency spectra of methyl radical to be placed on an absolute scale and will facilitate quantitative measurements of methyl concentrations by photoionization mass spectrometry.

Effect of Solvent Additives on the Solution Aggregation of Phenyl-C61-Butyl Acid Methyl Ester (PCBM)

KAUST Repository

Tummala, Naga Rajesh

2015-11-24

High-boiling-point solvent additives, employed during the solution processing of active-layer formulations, impact the efficiency of bulk hetero-junction (BHJ) organic solar cells by influencing the morphological / topological features of the multicomponent thin film. Here, we aim at a better understanding of how these additives change the aggregation landscape in the casting solution prior to film deposition via a multi-scale computational study of the aggregation phenomena of phenyl-C61-butyric-acid methyl ester (PCBM) in various solutions. The energetic landscape of PCBM-solvent / solvent-additive intermolecular interactions is evaluated at the electronic-structure level through symmetry-adapted perturbation theory to determine the nature and strength of non-covalent forces important to aggregation. Molecular dynamics simulations highlight how the choice of solvent and solvent additives control the formation of molecular aggregates. Our results indicate that high-boiling-point solvent additives change the effective interactions among the PCBM and casting-solvent molecules and alter the equilibrium PCBM aggregate sizes in solution.

A library synthesis of 4-hydroxy-3-methyl-6-phenylbenzofuran-2-carboxylic acid ethyl ester derivatives as anti-tumor agents.

Science.gov (United States)

Hayakawa, Ichiro; Shioya, Rieko; Agatsuma, Toshinori; Furukawa, Hidehiko; Naruto, Shunji; Sugano, Yuichi

2004-09-06

As a result of a hit-to-lead program using a technique of solution-phase parallel synthesis, a highly potent (2,4-dimethoxyphenyl)-[6-(3-fluorophenyl)-4-hydroxy-3-methylbenzofuran-2-yl]methanone (15b) was synthesized as an optimized derivative of 4-hydroxy-3-methyl-6-phenylbenzofuran-2-carboxylic acid ethyl ester (1), which was discovered as a screening hit from small-molecule libraries and exhibited selective cytotoxicity against a tumorigenic cell line.

Ketones blood test

Science.gov (United States)

Acetone bodies; Ketones - serum; Nitroprusside test; Ketone bodies - serum; Ketones - blood; Ketoacidosis - ketones blood test ... fat cells break down in the blood. This test is used to diagnose ketoacidosis . This is a ...

Spectral Analysis of 3-(Adamantan-1-yl)-4-Ethyl-1-[(4-Phenylpiperazin-1-yl) Methyl]-1 H-1,2,4-Triazole-5(4 H)-Thione

Science.gov (United States)

Mindarava, Y. L.; Shundalau, M. B.; Al-Wahaibi, L. H.; El-Emam, A. A.; Matsukovich, A. S.; Gaponenko, S. V.

2018-05-01

Vibrational IR (3200-650 cm-1) and Raman spectra (3200-150 cm-1) of adamantane-containing 3-(adamantan-1-yl)-4-ethyl-1-[(4-phenylpiperazin-1-yl)methyl]-1H-1,2,4-triazole-5(4H)-thione, which is promising for drug design, were examined. The UV/Vis spectrum (450-200 nm) of the compound in EtOH was measured. Full geometry optimization using density functional theory (DFT) in the B3LYP/cc-pVDZ approximation allowed the equilibrium configuration of the molecule to be determined and IR and Raman spectra to be calculated. Based on these, the experimental vibrational IR and Raman spectra were interpreted and the biological activity indices were predicted. The UV/Vis spectrum of the title compound was simulated at the time-dependent DFT/CAM-B3LYP/cc-pVDZ level with and without solvent effects and at the ab initio multi-reference perturbation theory XMCQDPT2 level. The UV/Vis spectrum that was simulated using the multi-reference XMCQDPT2 approximation agreed very successfully with the experimental data, in contrast to the single-reference DFT method. This was probably a consequence of intramolecular charge transfer.

Spectral Analysis of 3-(Adamantan-1-yl)-4-Ethyl-1-[(4-Phenylpiperazin-1-yl) Methyl]-1H-1,2,4-Triazole-5(4H)-Thione

Science.gov (United States)

Mindarava, Y. L.; Shundalau, M. B.; Al-Wahaibi, L. H.; El-Emam, A. A.; Matsukovich, A. S.; Gaponenko, S. V.

2018-05-01

Vibrational IR (3200-650 cm-1) and Raman spectra (3200-150 cm-1) of adamantane-containing 3-(adamantan-1-yl)-4-ethyl-1-[(4-phenylpiperazin-1-yl)methyl]-1H-1,2,4-triazole-5(4H)-thione, which is promising for drug design, were examined. The UV/Vis spectrum (450-200 nm) of the compound in EtOH was measured. Full geometry optimization using density functional theory (DFT) in the B3LYP/cc-pVDZ approximation allowed the equilibrium configuration of the molecule to be determined and IR and Raman spectra to be calculated. Based on these, the experimental vibrational IR and Raman spectra were interpreted and the biological activity indices were predicted. The UV/Vis spectrum of the title compound was simulated at the time-dependent DFT/CAM-B3LYP/cc-pVDZ level with and without solvent effects and at the ab initio multi-reference perturbation theory XMCQDPT2 level. The UV/Vis spectrum that was simulated using the multi-reference XMCQDPT2 approximation agreed very successfully with the experimental data, in contrast to the single-reference DFT method. This was probably a consequence of intramolecular charge transfer.

New RO TFC Membranes by Interfacial Polymerization in n-Dodecane with Various co-Solvents.

Science.gov (United States)

Al-Hobaib, Abdullah Sulaiman; Al-Suhybani, Mohammed Sulaiman; Al-Sheetan, Khalid Mohammed; Mousa, Hasan; Shaik, Mohammed Rafi

2016-04-29

The objective of this research is to prepare and characterize a new and highly efficient polyamide TFC RO membrane by interfacial polymerization in dodecane solvent mixed with co-solvents. Three co-solvents were tested namely; acetone, ethyl acetate, and diethyl ether of concentration of 0.5, 1, 2, 3, and 5 wt %. The modified membranes were characterized by SEM, EDX, AFM and contact angle techniques. The results showed that addition of co-solvent results in a decrease in the roughness, pore size and thickness of the produced membranes. However, as the concentration of the co-solvent increases the pore size of the membranes gets larger. Among the three co-solvents tested, acetone was found to result in membranes with the largest pore size and contact angle followed by diethyl ether then ethyl acetate. Measured contact angle increases as the concentration of the co-solvent increases reaching a constant value except for ethyl acetate where it was found to drop. Investigating flux and salt rejection by the formulated membranes showed that higher flux was attained when acetone was used as a co-solvent followed by diethyl ether then ethyl acetate. However, the highest salt rejection was achieved with diethyl ether.

Investigations into the chemistry, toxicology, metabolism and possible mode of action of O-ethyl S-methyl ethylphosphonothioate

International Nuclear Information System (INIS)

Hur, J.H.

1989-01-01

The chemical and metabolic oxidation of O-ethyl S-methyl ethylphosphonthioate (1) as a model compound was studied. This compound has the following toxicological properties: LD 50 (rat) 4.6 mg/kg, LD 50 (HF) 14.0 ug/g; k i (BAChE) = 303, k i (HFAChE) = 623. 13 C- and 31 P-NMR were mainly used in this study. The chemical oxidation of 1 with m-CPBA in CDCl 3 resulted in the formation of O-ethyl ethylphosphonic acid (2), O-ethyl ethylphosphinyloxymethylsulfonate (3) and O-ethyl ethylphosphonic acid anhydride (4). However, oxidation reaction of the model compound 1 with MPPA in D 2 O gave 2 and methylsulfonic acid. 1 was incubated in vitro with rat liver microsomal oxidase, and 2 and methylsulfenic acid were observed along with 1. For the in vivo study, a number of houseflies were treated with 14ug/g (LD 50 level) of 1. Analysis of the extracts of metabolic products provided evidence of the formation of 2. The existence of 1 S-oxide was demonstrated by use of a trapping method and the observation of oxidation products. The S-oxide has been proposed as a possible active intermediate responsible for the high toxicity of 1 to animals. However, owing to its instability it is unlikely that the S-oxide intermediate would persist in an aqueous biological environment long enough to attack the target enzyme. 4 was shown to have high toxicity to the rat and housefly and was also a potent anticholinesterase against BAChE and HFAChE . The presence of 4 was observed directly by the monitoring experiments during the chemical oxidation in aqueous conditions. This provided evidence that this metabolite is stable enough to attack the target site in biological systems. The anhydride 4 is proposed as the active metabolite in in vivo systems, responsible for high toxicity of 1

Solvent extraction of aromatic sulfur compounds from n-heptane using the 1-ethyl-3-methylimidazolium tricyanomethanide ionic liquid

International Nuclear Information System (INIS)

Królikowski, Marek; Walczak, Klaudia; Domańska, Urszula

2013-01-01

Highlights: • LLE data for (EMIMTCM + thiophene/benzothiophene + n-heptane) were determined. • High S and β for the extraction of thiophene/benzothiophene from n-heptane was found. • Results of S and β were compared with available literature. • The NRTL model satisfactorily correlates the LLE data. -- Abstract: The ionic liquid 1-ethyl-3-methylimidazolium tricyanomethanide ([EMIM][TCM]) has been tested as a solvent for the separation of sulfur compounds from aliphatic hydrocarbon. Liquid–liquid phase equilibrium data have been determined for ternary systems containing the ionic liquid, thiophene or benzothiophene and n-heptane. The influence of temperature on the separation of thiophene from n-heptane was determined. High solubility of sulfur compounds and practical immiscibility of aliphatic hydrocarbon in ionic liquid have been found. The values of selectivity and solute distribution ratios have been calculated for all systems and compared with literature data for other 1-ethyl-3-methylimidazolium-based ionic liquids. High values of selectivity were obtained. The experimental data were correlated using the NRTL equation, and the binary interaction parameters have been reported. The phase equilibria diagrams for the ternary mixtures including the experimental and calculated tie-lines have been presented

Nuclear reactor fuel element

International Nuclear Information System (INIS)

D'Eye, R.W.M.; Shennan, J.V.; Ford, L.H.

1977-01-01

Fuel element with particles from ceramic fissionable material (e.g. uranium carbide), each one being coated with pyrolitically deposited carbon and all of them being connected at their points of contact by means of an individual crossbar. The crossbar consists of silicon carbide produced by reaction of silicon metal powder with the carbon under the influence of heat. Previously the silicon metal powder together with the particles was kneaded in a solvent and a binder (e.g. epoxy resin in methyl ethyl ketone plus setting agent) to from a pulp. The reaction temperature lies at 1750 0 C. The reaction itself may take place in a nitrogen atmosphere. There will be produced a fuel element with a high overall thermal conductivity. (DG) [de

Experimental density, viscosity, interfacial tension and water solubility of ethyl benzene-α-methyl benzyl alcohol–water system

International Nuclear Information System (INIS)

Barega, Esayas W.; Zondervan, Edwin; Haan, André B. de

2013-01-01

Highlights: • Properties were measured for MBA (methyl benzyl alcohol)-EB (ethyl benzene)-water. • MBA concentration was found to influence all the properties strongly. • The water solubility, density, and viscosity increased at high MBA concentration. • The interfacial tension decreased sharply at high MBA concentration. • MBA dictates the phase separation and mass transfer of the ternary system. -- Abstract: Density, viscosity, interfacial tension, and water solubility were measured for the (α-methyl benzyl alcohol (MBA) + Ethyl benzene (EB)) system at different concentrations of MBA in contact with water and sodium hydroxide solution (0.01 mol · kg −1 ) as aqueous phases. The properties were measured to identify the component which plays a governing role in changing the physical properties relevant to mass transfer and phase separation of the ternary system. The concentration of MBA was found to be the major factor influencing all the properties. The water solubility, the density, and the viscosity increased notably at higher concentrations of MBA; while, the interfacial tension decreased strongly. The use of 0.01 mol · kg −1 NaOH as an aqueous phase resulted in a decrease of the interfacial tension and a minor decrease in the water solubility. The density data were correlated using a quadratic mixing rule to describe the influence of concentration at any temperature. The viscosity data are correlated using the Nissan and Grunberg and Katti-Chaudhri equations. The Szyzkowski’s equation was used to correlate the interfacial tension data. The water solubility data were described using an exponential relationship. All the correlations described the experimental physical property data adequately

Preparation of planar CH3NH3PbI3 thin films with controlled size using 1-ethyl-2-pyrrolidone as solvent

International Nuclear Information System (INIS)

Hao, Qiuyan; Chu, Yixia; Zheng, Xuerong; Liu, Zhenya; Liang, Liming; Qi, Jiakun; Zhang, Xin; Liu, Gang; Liu, Hui; Chen, Hongjian; Liu, Caichi

2016-01-01

Recently, planar perovskite solar cells based on CH 3 NH 3 PbI 3 have attracted many researcher's interest due to their unique advantages such as simple cell architecture, easy fabrication and potential multijunction construction comparing to the initial mesoporous structure. However, the preparation of planar perovskite films with high quality is still in challenge. In this paper, we developed a vapor-assisted solution process using a novel and green solvent of 1-Ethyl-2-pyrrolidone (NEP) instead of the traditional N, N-dimethylformamide (DMF) to construct a high-quality perovskite CH 3 NH 3 PbI 3 thin film with pure phase, high compactness, small surface roughness and controlled size. The phase evolution and growth mechanism of the perovskite films are also discussed. Utilizing the NEP of low volatility and moderate boiling point as solvent, we dried the PbI 2 -NEP precursor films at different temperature under vacuum and then obtained PbI 2 thin films with different crystalline degree from amorphous to highly crystalline. The perovskite films with crystal size ranged from hundreds of nanometers to several micrometers can be prepared by reacting the PbI 2 films of different crystalline degree with CH 3 NH 3 I vapor. Moreover, planar-structured solar cells combining the perovskite film with TiO 2 and spiro-OMeTAD as the electron and holes transporting layer achieves a power conversion efficiency of 10.2%. - Highlights: • A novel and green solvent of 1-Ethyl-2-pyrrolidone (NEP) was used to construct high-quality perovskite CH 3 NH 3 PbI 3 thin film. • The CH 3 NH 3 PbI 3 grain with different sizes ranged from hundreds of nanometers to several micrometers can be obtained. • Planar-structured perovskite CH 3 NH 3 PbI 3 solar cells using NEP as solvent achieves a power conversion efficiency of 10.2%.

Microalgae wet extraction using N-ethyl butylamine for fatty acid production

Directory of Open Access Journals (Sweden)

Ying Du

2016-04-01

Full Text Available Microalgae are considered a promising feedstock for the production of food ingredients, cosmetics, pharmaceutical products and biofuels. The energy intensity of drying and cell breaking of algae and solvent recovery afterwards hindered the route of algae biorefinery. In this work the influences of freeze drying and cell breaking to the extraction efficiency of crude lipid yield and fatty acid yield were investigated. Results showed that drying and cell breaking are not necessary for N-ethyl butylamine extraction, because good yields were obtained without. Crude lipid yield and fatty acid yield using N-ethyl butylamine were comparable with Bligh & Dyer extraction, making N-ethyl butylamine a candidate for further development of an energy efficient lipid extraction technology for non-broken microalgae. Keywords: Microalgae, Lipids, Extraction, Switchable solvent, Secondary amine

The effects of a co-solvent on fabrication of cellulose acetate membranes from solutions in 1-ethyl-3-methylimidazolium acetate

KAUST Repository

Kim, Dooli

2016-08-15

Ionic liquids have been considered green solvents for membrane fabrication. However, the high viscosity of their polymer solutions hinders the formation of membranes with strong mechanical properties. In this study, acetone was explored as a co-solvent with the ionic liquid 1-ethyl-3-methylimidazolium acetate ([EMIM]OAc) to dissolve cellulose acetate. The effects of acetone on the thermodynamic and kinetic aspects of the polymer solutions were studied and the physicochemical properties and separation capability of their resultant membranes were analyzed. The Hansen solubility parameters of [EMIM]OAc were measured by the software HSPiP and these data demonstrated that acetone was a suitable co-solvent to increase the solubility of cellulose acetate. The Gibbs free energy of mixing ΔGm was estimated to determine the proper composition of the polymer solution with better solubility. The study of the kinetics of phase separation showed that the demixing rate of the CA polymer solution in acetone and [EMIM]OAc was higher than that for solutions in [EMIM]OAc only. The membranes prepared from the former solution had higher water permeance and better mechanical stability than those prepared from the later solution. Adding acetone as a co-solvent opened the opportunity of fabricating membranes with higher polymer concentrations for higher separation capability and better mechanical properties. © 2016

The effects of a co-solvent on fabrication of cellulose acetate membranes from solutions in 1-ethyl-3-methylimidazolium acetate

KAUST Repository

Kim, Dooli; Le, Ngoc Lieu; Nunes, Suzana Pereira

2016-01-01

Ionic liquids have been considered green solvents for membrane fabrication. However, the high viscosity of their polymer solutions hinders the formation of membranes with strong mechanical properties. In this study, acetone was explored as a co-solvent with the ionic liquid 1-ethyl-3-methylimidazolium acetate ([EMIM]OAc) to dissolve cellulose acetate. The effects of acetone on the thermodynamic and kinetic aspects of the polymer solutions were studied and the physicochemical properties and separation capability of their resultant membranes were analyzed. The Hansen solubility parameters of [EMIM]OAc were measured by the software HSPiP and these data demonstrated that acetone was a suitable co-solvent to increase the solubility of cellulose acetate. The Gibbs free energy of mixing ΔGm was estimated to determine the proper composition of the polymer solution with better solubility. The study of the kinetics of phase separation showed that the demixing rate of the CA polymer solution in acetone and [EMIM]OAc was higher than that for solutions in [EMIM]OAc only. The membranes prepared from the former solution had higher water permeance and better mechanical stability than those prepared from the later solution. Adding acetone as a co-solvent opened the opportunity of fabricating membranes with higher polymer concentrations for higher separation capability and better mechanical properties. © 2016

Sub-chronic toxicity of low concentrations of industrial volatile organic pollutants in vitro

International Nuclear Information System (INIS)

McDermott, Catherine; Allshire, Ashley; Pelt, Frank N.A.M. van; Heffron, James J.A.

2007-01-01

Organic solvents form an important class of pollutants in the ambient air and have been associated with neurotoxicity and immunotoxicity in humans. Here we investigated the biological effects of sub-chronic exposure to industrially important volatile organic solvents in vitro. Jurkat T cells were exposed to toluene, n-hexane and methyl ethyl ketone (MEK) individually for 5 days and solvent exposure levels were confirmed by headspace gas chromatography. A neuroblastoma cell line (SH-SY5Y) was exposed to toluene for the same period. Following exposure, cells were harvested and toxicity measured in terms of the following endpoints: membrane damage (LDH leakage), perturbations in intracellular free Ca 2+ , changes in glutathione redox status and dual-phosphorylation of MAP kinases ERK1/2, JNK and p38. The results show that sub-chronic exposure to the volatile organic solvents causes membrane damage, increased intracellular free calcium and altered glutathione redox status in both cell lines. However, acute and sub-chronic solvent exposure did not result in MAP kinase phosphorylation. Toxicity of the solvents tested increased with hydrophobicity. The lowest-observed-adverse-effect-levels (LOAELs) measured in vitro were close to blood solvent concentrations reported for individuals exposed to the agents at levels at or below their individual threshold limit values (TLVs)

Separation and Analysis of Microwave-assisted Liquefied Products of Corn Stover

Directory of Open Access Journals (Sweden)

Weihua Xiao

2014-10-01

Full Text Available Corn stover was successfully liquefied by microwave heating at 160 °C with ethylene glycol (EG used as the solvent and sulfuric acid as a catalyst. Gas chromatography and mass spectrometry (GC-MS data indicated that methyl esters, including 3-(2-methyl-1,3-doxolane-2-yl propionic acid methyl ester (PAME, levulinic acid isopropyl ester (LAE, methyl laurate, and methyl palmitate were the major degradation compounds, in addition to EG derivatives in the liquefied product of corn stover (LPCS. For high value-added utilization of LPCS, solvent extraction was applied to characterize the components and to separate it into useful fractions. After being dispersed in water, the water-soluble fraction of the LPCS was then extracted with organic solvents, including hexane, chloroform, diethyl ether, and ethyl acetate. Levulinic acid isopropyl ester showed the highest distribution in chloroform and ethyl acetate, while the lowest in hexane and ether. Levulinic acid isopropyl ester was selectively enriched to 28.76% and 43.65% by sequential extraction with chloroform and ethyl acetate, respectively, in accordance with the quantitative analysis.

Elimination of the reactivation process in the adhesion of chlorinated SBS rubber with polychloroprene adhesives

Directory of Open Access Journals (Sweden)

2007-04-01

Full Text Available Chlorination treatment of a thermoplastic styrene-butadiene-styrene rubber (SBS with a 3 wt% solution of trichloroisocyanuric acid (TCI in methyl ethyl ketone (MEK introduces chlorinated and oxidized moieties on the rubber surface which increase its surface energy and produces surface microroughness. Consequently adhesion properties, evaluated by T-peel strength measurements in chlorinated SBS/solvent based-polyurethane adhesive/leather joints, are enhanced. In this study, two solvent-based polychloroprene adhesives (PCP0 and PCP30R have been considered as an alternative to the commonly used solvent-based polyurethane adhesive (PU. A thermoreactive phenolic resin was added to one of the polychloroprene adhesive formulations (PCP30R. This tackifier resin favors chlorination of the adhesive and reinforces the interface between the chlorinated adhesive and the chlorinated rubber surface. Besides, PCP30R adhesive does not need adhesive reactivation and considerable high T-peel strength value (5.7±0.3 kN/m was obtained. Elimination of the reactivation process implies a considerable improvement of the manufacturing process in the footwear industry.

Potentiometric titrations of para and nitro substituted aromatic acids and their mixtures in methylethyl ketone

International Nuclear Information System (INIS)

Ozeroglu, C.; Karahan, M.

2011-01-01

In this study, it was the purpose to examine the potentiometric titrations of para and nitro substituted aromatic acids in methylethyl ketone (MEK) as a non-aqueous solvent. Good analytical results were obtained in determining the amount of each acid and the amounts of acids in their ternary mixtures by using 0.0964 N tetrabuthylammoniumhydroxyde (TBAH) as a standard titrant. Methylethyl ketone (MEK) which is a good solvent for many organic compounds and has a convenient liquid range of -86 to 80 deg. C was used for titration of the para and nitro substituted aromatic acids. A linear relationship has been found between pKa values of the para and nitro substituted aromatic acids in water and the half neutralization potential (HNP) values determined by potentiometric titration curves of the same acids in MEK. (author)

Extraction of Betulin, Trimyristin, Eugenol and Carnosic Acid Using Water-Organic Solvent Mixtures

Directory of Open Access Journals (Sweden)

Fulgentius N. Lugemwa

2012-08-01

Full Text Available A solvent system consisting of ethyl acetate, ethyl alcohol and water, in the volume ratio of 4.5:4.5:1, was developed and used to extract, at room temperature, betulin from white birch bark and antioxidants from spices (rosemary, thyme, sage, and oregano and white oak chips. In addition, under reflux conditions, trimyristin was extracted from nutmeg using the same solvent system, and eugenol from olives was extracted using a mixture of salt water and ethyl acetate. The protocol demonstrates the use of water in organic solvents to extract natural products from plants. Measurement of the free-radical scavenging activity using by 2,2-diphenyl-1-picrylhydrazyl (DPPH indicated that the extraction of plant material using ethyl acetate, ethyl alcohol and water (4.5:4.5:1, v/v/v was exhaustive when carried out at room temperature for 96 h.

Efficient production of fatty acid methyl ester from waste activated bleaching earth using diesel oil as organic solvent.

Science.gov (United States)

Kojima, Seiji; Du, Dongning; Sato, Masayasu; Park, Enoch Y

2004-01-01

Fatty acid methyl ester (FAME) production from waste activated bleaching earth (ABE) discarded by the crude oil refining industry was investigated using fossil fuel as a solvent in the esterification of triglycerides. Lipase from Candida cylindracea showed the highest stability in diesel oil. Using diesel oil as a solvent, 3 h was sufficient to obtain a yield of approximately 100% of FAME in the presence of 10% lipase from waste ABE. Kerosene was also a good solvent in the esterification of triglycerides embedded in the waste ABE. Fuel analysis showed that the FAME produced using diesel oil as a solvent complied with the Japanese diesel standard and the 10% residual carbon amount was lower than that of FAME produced using other solvents. Use of diesel oil as solvent in the FAME production from the waste ABE simplified the process, because there was no need to separate the organic solvent from the FAME-solvent mixture. These results demonstrate a promising reutilization method for the production of FAME, for use as a biodiesel, from industrial waste resources containing waste vegetable oils.

Solvent and polymer concentration effects on the surface morphology evolution of immiscible polystyrene/poly(methyl methacrylate) blends

International Nuclear Information System (INIS)

Cui Liang; Ding Yan; Li Xue; Wang Zhe; Han Yanchun

2006-01-01

The effects of solvent nature on the surface topographies of polystyrene (PS)/poly(methyl methacrylate) (PMMA) blend films spin-coated onto the silicon wafer were investigated. Four different solvents, such as ethylbenzene, toluene, tetrahydrofuran and dichloromethane, were chosen. They are better solvents for PS than that for PMMA. When dichloromethane, tetrahydrofuran and toluene were used, PMMA-rich phase domains protruded from the background of PS. When ethylbenzene was used, PS-rich phase domains elevated on the average height of PMMA-rich phase domains. In addition, continuous pits, networks and isolated droplets consisted of PS formed on the blend film surfaces with the decrease of polymer concentrations. The mechanism of the surface morphology evolution was discussed in detail

U.S. Air Force Installation Restoration Program. Phase 1. Records Search for Suffolk County Air Force Base (Retired) Landfills 1 and 2. Suffolk County Airport, Westhampton Beach, New York.

Science.gov (United States)

1987-09-20

2- methyl -3-pentanone, 2,4-dimethyl-3-pentanone) was confirmed; no concentrations were reported. Thirty other volatile compounds were analyzed for but...of central Long Island, are characterized by open, sunlit, woodlands dominated by pitch pine ( Pinus rigida). This overstory species is interspersed...including, but not necessarily limited to, kerosene, mineral spirits, trichloroethylene, methyl ethyl ketone (MEK), and toluene , and contaminated fuels

Biochemical characterization of a recombinant short-chain NAD(H)-dependent dehydrogenase/reductase from Sulfolobus acidocaldarius.

Science.gov (United States)

Pennacchio, Angela; Giordano, Assunta; Pucci, Biagio; Rossi, Mosè; Raia, Carlo A

2010-03-01

The gene encoding a novel alcohol dehydrogenase that belongs to the short-chain dehydrogenases/reductases (SDRs) superfamily was identified in the aerobic thermoacidophilic crenarchaeon Sulfolobus acidocaldarius strain DSM 639. The saadh gene was heterologously overexpressed in Escherichia coli, and the protein (SaADH) was purified to homogeneity and characterized. SaADH is a tetrameric enzyme consisting of identical 28,978-Da subunits, each composed of 264 amino acids. The enzyme has remarkable thermophilicity and thermal stability, displaying activity at temperatures up to 75 degrees C and a 30-min half-inactivation temperature of ~90 degrees C, and shows good tolerance to common organic solvents. SaADH has a strict requirement for NAD(H) as the coenzyme, and displays a preference for the reduction of alicyclic, bicyclic and aromatic ketones and alpha-keto esters, but is poorly active on aliphatic, cyclic and aromatic alcohols, and shows no activity on aldehydes. The enzyme catalyses the reduction of alpha-methyl and alpha-ethyl benzoylformate, and methyl o-chlorobenzoylformate with 100% conversion to methyl (S)-mandelate [17% enantiomeric excess (ee)], ethyl (R)-mandelate (50% ee), and methyl (R)-o-chloromandelate (72% ee), respectively, with an efficient in situ NADH-recycling system which involves glucose and a thermophilic glucose dehydrogenase. This study provides further evidence supporting the critical role of the D37 residue in discriminating NAD(H) from NAD(P)H in members of the SDR superfamily.

Agglomeration of Celecoxib by Quasi Emulsion Solvent Diffusion Method: Effect of Stabilizer

Directory of Open Access Journals (Sweden)

Maryam Maghsoodi

2016-12-01

Full Text Available Purpose: The quasi-emulsion solvent diffusion (QESD has evolved into an effective technique to manufacture agglomerates of API crystals. Although, the proposed technique showed benefits, such as cost effectiveness, that is considerably sensitive to the choice of a stabilizer, which agonizes from a absence of systemic understanding in this field. In the present study, the combination of different solvents and stabilizers were compared to investigate any connections between the solvents and stabilizers. Methods: Agglomerates of celecoxib were prepared by QESD method using four different stabilizers (Tween 80, HPMC, PVP and SLS and three different solvents (methyl acetate, ethyl acetate and isopropyl acetate. The solid state of obtained particles was investigated by differential scanning calorimetry (DSC and Fourier transform infrared (FT-IR spectroscopy. The agglomerated were also evaluated in term of production yield, distribution of particles and dissolution behavior. Results: The results showed that the effectiveness of stabilizer in terms of particle size and particle size distribution is specific to each solvent candidate. A stabilizer with a lower HLB value is preferred which actually increased its effectiveness with the solvent candidates with higher lipophilicity. HPMC appeared to be the most versatile stabilizer because it showed a better stabilizing effect compared to other stabilizers in all solvents used. Conclusion: This study demonstrated that the efficiency of stabilizers in forming the celecoxib agglomerates by QESD was influenced by the HLB of the stabilizer and lipophilicity of the solvents.

Solvent Dependency in the Quantum Efficiency of 4-[(4-Aminophenyl)-(4-imino-1-cyclohexa-2, 5- dienylidene) methyl] Aniline Hydrochloride.

Science.gov (United States)

Pathrose, Bini; Nampoori, V P N; Radhakrishnan, P; Sahira, H; Mujeeb, A

2015-05-01

In the present work dual beam thermal lens technique is used for studying the solvent dependency on the quantum efficiency of a novel dye used for biomedical applications. The role of solvent in the absolute fluorescence quantum yield of 4-[(4-Aminophenyl)-(4-imino-1-cyclohexa-2, 5- dienylidene) methyl] aniline hydrochloride is studied using thermal lens technique. It is observed that the variation in solvents and its concentration results considerable variations in the fluorescence quantum yield. These variations are due to the non-radiative relaxation of the absorbed energy and because of the different solvent properties. The highest quantum yield of the dye is observed in the polar protic solvent-water.

SPECTROSCOPIC CHARACTERIZATION AND DETECTION OF ETHYL MERCAPTAN IN ORION

International Nuclear Information System (INIS)

Kolesniková, L.; Alonso, J. L.; Daly, A. M.; Tercero, B.; Cernicharo, J.; Gordon, B. P.; Shipman, S. T.

2014-01-01

New laboratory data of ethyl mercaptan, CH 3 CH 2 SH, in the millimeter- and submillimeter-wave domains (up to 880 GHz) provided very precise values of the spectroscopic constants that allowed the detection of gauche-CH 3 CH 2 SH toward Orion KL. This identification is supported by 77 unblended or slightly blended lines plus no missing transitions in the range 80-280 GHz. A detection of methyl mercaptan, CH 3 SH, in the spectral survey of Orion KL is reported as well. Our column density results indicate that methyl mercaptan is ≅ 5 times more abundant than ethyl mercaptan in the hot core of Orion KL

SPECTROSCOPIC CHARACTERIZATION AND DETECTION OF ETHYL MERCAPTAN IN ORION

Energy Technology Data Exchange (ETDEWEB)

Kolesniková, L.; Alonso, J. L.; Daly, A. M. [Grupo de Espectroscopía Molecular (GEM), Edificio Quifima, Laboratorios de Espectroscopía y Bioespectroscopía, Parque Científico UVa, Unidad Asociada CSIC, Universidad de Valladolid, E-47011 Valladolid (Spain); Tercero, B.; Cernicharo, J. [Departamento de Astrofísica, Centro de Astrobiología CAB, CSIC-INTA, Ctra. de Torrejón a Ajalvir km 4, E-28850 Madrid (Spain); Gordon, B. P.; Shipman, S. T., E-mail: lucie.kolesnikova@uva.es, E-mail: jlalonso@qf.uva.es, E-mail: adammichael.daly@uva.es, E-mail: terceromb@cab.inta-csic.es, E-mail: jcernicharo@cab.inta-csic.es, E-mail: brittany.gordon@ncf.edu, E-mail: shipman@ncf.edu [Division of Natural Sciences, New College of Florida, Sarasota, FL 34243 (United States)

2014-03-20

New laboratory data of ethyl mercaptan, CH{sub 3}CH{sub 2}SH, in the millimeter- and submillimeter-wave domains (up to 880 GHz) provided very precise values of the spectroscopic constants that allowed the detection of gauche-CH{sub 3}CH{sub 2}SH toward Orion KL. This identification is supported by 77 unblended or slightly blended lines plus no missing transitions in the range 80-280 GHz. A detection of methyl mercaptan, CH{sub 3}SH, in the spectral survey of Orion KL is reported as well. Our column density results indicate that methyl mercaptan is ≅ 5 times more abundant than ethyl mercaptan in the hot core of Orion KL.

Density, refraction index and vapor–liquid equilibria of N-methyl-2-hydroxyethylammonium butyrate plus (methyl acetate or ethyl acetate or propyl acetate) at several temperatures

International Nuclear Information System (INIS)

Alvarez, V.H.; Mattedi, S.; Aznar, M.

2013-01-01

Highlights: ► Densities, refraction indices and VLE were measured for ester + m-2-HEAB mixtures. ► V E , apparent molar volumes and thermal expansion coefficients were calculated. ► Peng–Robinson EoS + Wong–Sandler mixing rule + COSMO-SAC predicted the data. -- Abstract: This paper reports the densities, refraction indices, and vapor liquid equilibria for binary systems ester + N-methyl-2-hydroxyethylammonium butyrate (m-2-HEAB): methyl acetate (1) + m-2-HEAB (2), ethyl acetate (1) + m-2-HEAB and propyl acetate (1) + m-2-HEAB (2). The excess molar volumes, deviations in the refraction index, apparent molar volumes, and thermal expansion coefficients for the binary systems were fitted to polynomial equations. The Peng–Robinson equation of state, coupled with the Wong–Sandler mixing rule, is used to describe the experimental data. Since the predictive activity coefficient model COSMO-SAC is used in the Wong–Sandler mixing rule, the resulting thermodynamic model is a completely predictive one. The prediction results for the density and for the vapor–liquid equilibria have a deviation lower than 1.0% and 1.1%, respectively

Enhanced susceptibility of a transposable-element-bearing strain of Drosophila melanogaster to somatic eye-color mutations by ethyl nitrosourea, methyl nitrosourea, and X-rays

International Nuclear Information System (INIS)

Ryo, H.; Kondo, S.; Rasmuson, B.

1983-01-01

A strain of Drosophila with the genes z and w + plus a transposable element (TE) is about 3 times more sensitive than a strain without TE toward somatic eye-color mutations after larval exposure to ethyl nitrosourea, methyl nitrosourea and X-rays. The assay system with TE is simple, reliable, and sensitive for detecting somatic mutations induced in vivo by mutagens. (orig.)

Atomic-absorption determination of mercury in geological materials by flame and carbon-rod atomisation after solvent extraction and using co-extracted silver as a matrix modifier

Science.gov (United States)

Sanzolone, R.F.; Chao, T.T.

1983-01-01

Based on modifications and expansion of the original Tindall's solvent extraction flame atomic-absorption procedure, an atomic-absorption spectrophotometric method has been developed for the determination of mercury in geological materials. The sample is digested with nitric and hydrochloric acids in a boiling water-bath. The solution is made ammoniacal and potassium iodide and silver nitrate are added. The mercury is extracted into isobutyl methyl ketone as the tetraiodomercurate(ll). Added silver is co-extracted with mercury and serves as a matrix modifier in the carbon-rod atomiser. The mercury in the isobutyl methyl ketone extract may be determined by either the flame- or the carbon-rod atomisation method, depending on the concentration level. The limits of determination are 0.05-10 p.p.m. of mercury for the carbon-rod atomisation and 1 -200 p.p.m. of mercury for the flame atomisation. Mercury values for reference samples obtained by replicate analyses are in good agreement with those reported by other workers, with relative standard deviations ranging from 2.3 to 0.9%. Recoveries of mercury spiked at two levels were 93-106%. Major and trace elements commonly found in geological materials do not interfere.

Solvent-free enzymatic synthesis of feruloylated structured lipids by the transesterification of ethyl ferulate with castor oil.

Science.gov (United States)

Sun, Shangde; Zhu, Sha; Bi, Yanlan

2014-09-01

A novel enzymatic route of feruloylated structured lipids synthesis by the transesterification of ethyl ferulate (EF) with castor oil, in solvent-free system, was investigated. The transesterification reactions were catalysed by Novozym 435, Lipozyme RMIM, and Lipozyme TLIM, among which Novozym 435 showed the best catalysis performance. Effects of feruloyl donors, reaction variables, and ethanol removal on the transesterification were also studied. High EF conversion (∼100%) was obtained under the following conditions: enzyme load 20% (w/w, relative to the weight of substrates), reaction temperature 90 °C, substrate molar ratio 1:1 (EF/castor oil), 72 h, vacuum pressure 10 mmHg, and 200 rpm. Under these conditions, the transesterification product consisted of 62.6% lipophilic feruloylated structured lipids and 37.3% hydrophilic feruloylated lipids. Copyright © 2014 Elsevier Ltd. All rights reserved.

Efficient hydrodeoxygenation of biomass-derived ketones over bifunctional Pt-polyoxometalate catalyst.

Science.gov (United States)

Alotaibi, Mshari A; Kozhevnikova, Elena F; Kozhevnikov, Ivan V

2012-07-21

Acidic heteropoly salt Cs(2.5)H(0.5)PW(12)O(40) doped with Pt nanoparticles is a highly active and selective catalyst for one-step hydrogenation of methyl isobutyl and diisobutyl ketones to the corresponding alkanes in the gas phase at 100 °C with 97-99% yield via metal-acid bifunctional catalysis.

Reaction rate constants of H-abstraction by OH from large ketones: measurements and site-specific rate rules.

Science.gov (United States)

Badra, Jihad; Elwardany, Ahmed E; Farooq, Aamir

2014-06-28

Reaction rate constants of the reaction of four large ketones with hydroxyl (OH) are investigated behind reflected shock waves using OH laser absorption. The studied ketones are isomers of hexanone and include 2-hexanone, 3-hexanone, 3-methyl-2-pentanone, and 4-methl-2-pentanone. Rate constants are measured under pseudo-first-order kinetics at temperatures ranging from 866 K to 1375 K and pressures near 1.5 atm. The reported high-temperature rate constant measurements are the first direct measurements for these ketones under combustion-relevant conditions. The effects of the position of the carbonyl group (C=O) and methyl (CH3) branching on the overall rate constant with OH are examined. Using previously published data, rate constant expressions covering, low-to-high temperatures, are developed for acetone, 2-butanone, 3-pentanone, and the hexanone isomers studied here. These Arrhenius expressions are used to devise rate rules for H-abstraction from various sites. Specifically, the current scheme is applied with good success to H-abstraction by OH from a series of n-ketones. Finally, general expressions for primary and secondary site-specific H-abstraction by OH from ketones are proposed as follows (the subscript numbers indicate the number of carbon atoms bonded to the next-nearest-neighbor carbon atom, the subscript CO indicates that the abstraction is from a site next to the carbonyl group (C=O), and the prime is used to differentiate different neighboring environments of a methylene group):

Synthesis, and anticonvulsant activity of new amides derived from 3-methyl- or 3-ethyl-3-methyl-2,5-dioxo-pyrrolidin-1-yl-acetic acids.

Science.gov (United States)

Obniska, Jolanta; Rapacz, Anna; Rybka, Sabina; Góra, Małgorzata; Kamiński, Krzysztof; Sałat, Kinga; Żmudzki, Paweł

2016-04-15

This paper describes the synthesis of the library of 22 new 3-methyl- and 3-ethyl-3-methyl-2,5-dioxo-pyrrolidin-1-yl-acetamides as potential anticonvulsant agents. The maximal electroshock (MES) and the subcutaneous pentylenetetrazole (scPTZ) seizure models were used for screening all the compounds. The 6 Hz model of pharmacoresistant limbic seizures was applied for studying selected derivatives. Six amides were chosen for pharmacological characterization of their antinociceptive activity in the formalin model of tonic pain as well as local anesthetic activity was assessed in mice. The pharmacological data indicate on the broad spectra of activity across the preclinical seizure models. Compounds 10 (ED50=32.08 mg/kg, MES test) and 9 (ED50=40.34 mg/kg, scPTZ test) demonstrated the highest potency. These compounds displayed considerably better safety profiles than clinically relevant antiepileptic drugs phenytoin, ethosuximide, or valproic acid. Several molecules showed antinociceptive and local anesthetic properties. The in vitro radioligand binding studies demonstrated that the influence on the sodium and calcium channels may be one of the essential mechanisms of action. Copyright © 2016. Published by Elsevier Ltd.

Simultaneous Enhancement of Electrical Conductivity and Seebeck Coefficient of [6,6]-Phenyl-C71 Butyric Acid Methyl Ester (PC70BM by Adding Co-Solvents

Directory of Open Access Journals (Sweden)

Mina Rastegaralam

2018-05-01

Full Text Available Chemical modification by co-solvents added to [6,6]-Phenyl-C71 butyric acid methyl ester, commonly known as an n-type semiconducting fullerene derivative PC70BM, is reported to change the electrical and thermoelectric properties of this system. Power factor of the casted PC70BM samples achieves values higher than that determined for a variety of organic compounds, including conducting polymers, such as PEDOT:PSS in the pristine form. After chemical functionalization by different solvents, namely N,N-Dimethylformamide (DMF, dimethyl sulfoxide (DMSO, N-Methyl-2-pyrrolidone (NMP, acetonitrile (AC, and 1,2-Dichloroethane (DCE, the four-probe in-plane electrical conductivity and Seebeck coefficient measurements indicate a simultaneous increase of the electrical conductivity and the Seebeck coefficient. The observed effect is more pronounced for solvents with a high boiling point, such as N,N-Dimethylformamide (DMF, dimethyl sulfoxide (DMSO, and N-Methyl-2-pyrrolidone (NMP, than in acetonitrile (AC and 1,2-Dichloroethane (DCE. We identified the origin of these changes using Hall mobility measurements, which demonstrate enhancement of the PC70BM charge carrier mobility upon addition of the corresponding solvents due to the improved packaging of the fullerene compound and chemical interaction with entrapped solvent molecules within the layers.

Cobalt(ll) Coordination Compounds of Ethyl 4-Methyl-5-Imidazolecarboxylate: Chemical and Biochemical Characterization on Photosynthesis and Seed Germination

OpenAIRE

King-Díaz, Beatriz; Montes-Ayala, Josefina; Escartín-Guzmán, Concepción; Castillo-Blum, Silvia E.; Iglesias-Prieto, Roberto; Lotina-Hennsen, Blas; Barba-Behrens, Norah

2005-01-01

In this work we present the synthesis, structural and spectroscopic characterization of Co2+ coordination compounds with ethyl 4-methyl-5-imidazolecarboxylate (emizco). The effects of emizco, the metal salts CoCl2.6H2O, CoBr2, Co(NO3)2.6H2O and their metal coordination compounds [Co(emizco)2Cl2], [Co(emizco)2 Br2].H2O, [Co(emizco)2 (H2O)2(NO2)2.2H2O were evaluated on photosynthesis in spinach chloroplasts. Seed germination and seedling growth of the monocotyledonous species Lolium multiflorum...

Extraction of europium with thenoyltrifluoroacetone into alcohol, ketone and ester solvents

International Nuclear Information System (INIS)

Akiba, K.; Kanno, T.

1980-01-01

The effect of solvent has been studied on the extraction of tris-thenoyltrifluoroacetone (TTA) chelate of europium(III). Donor-active solvents (S) greatly promote the extraction owing to the formation of solvate species EuA 3 .mS (m = 1,2). Linear relations were established between the distribution of ratios of europium (Dsub(Eu)) and the partition constants of TTA (Psub(HA)); log Dsub(Eu) (at a definite pA) = a log Psub(HA) + b, where constants a and b were empirically determined for each series of solvents. The regularity is interpreted in terms of dual roles of solvent as donor and as medium. (author)

Direct Conversion of Cellulose into Ethyl Lactate in Supercritical Ethanol-Water Solutions.

Science.gov (United States)

Yang, Lisha; Yang, Xiaokun; Tian, Elli; Lin, Hongfei

2016-01-08

Biomass-derived ethyl lactate is a green solvent with a growing market as the replacement for petroleum-derived toxic organic solvents. Here we report, for the first time, the production of ethyl lactate directly from cellulose with the mesoporous Zr-SBA-15 silicate catalyst in a supercritical mixture of ethanol and water. The relatively strong Lewis and weak Brønsted acid sites on the catalyst, as well as the surface hydrophobicity, were beneficial to the reaction and led to synergy during consecutive reactions, such as depolymerization, retro-aldol condensation, and esterification. Under the optimum reaction conditions, ∼33 % yield of ethyl lactate was produced from cellulose with the Zr-SBA-15 catalyst at 260 °C in supercritical 95:5 (w/w) ethanol/water. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The International Workshop on Flame Chemistry (1st) Held in Warsaw, Poland on 28-29 July 2012

Science.gov (United States)

2012-07-01

methyl esters ( FAMEs ): Westbrook et al. Proc. Comb. Inst. (2012) in press. Paper 3D03...HCO CH3O + CO CH3 + CO2 H + CO HO2 + CO 35% 18% 42% +R/-RH +R/-RH 62%38% 81% 9% 88% 12% +M +O2 Impact of alkyl chain length on methyl ester reactivity...Alcohols (methanol, ethanol, propanol, butanol) Ethers (DME, DEE, EME, MTBE, ETBE)  Esters ( methyl and ethyl esters ) Ketones (acetone, EMK,

Migration of toxicants from plastics into drinking water during storage ...

African Journals Online (AJOL)

In this study, migration of toxicants, such as, manufacturing additives and previously adsorbed materials into drinking water stored inside plastic containers was investigated. The study considered virgin containers as well as those previously used to store sulphuric acid, calcium hypochlorite, methyl ethyl ketone (MEK) and ...

Comparison of Cashew Nut Shell Liquid (CNS) Resin with Polyester ...

African Journals Online (AJOL)

Akorede

cobalt amine (accelerator), methyl ethyl ketone peroxide (catalyst) to develop two sets of ... shell liquid (CNSL) resin were comparable to those developed with polyester resin. ... permit diffusion of water, this function is often not adequately ... When designed ... blades in gas turbine engines, wing leading edges and flaps.

40 CFR Appendix Vii to Part 261 - Basis for Listing Hazardous Waste

Science.gov (United States)

2010-07-01

..., acetonitrile, hydrocyanic acid. K013 Hydrocyanic acid, acrylonitrile, acetonitrile. K014 Acetonitrile..., trichlorofluoromethane. F003 N.A. F004 Cresols and cresylic acid, nitrobenzene. F005 Toluene, methyl ethyl ketone, carbon... -tetrachlorophenols and their chlorophenoxy derivative acids, esters, ethers, amine and other salts. F021 Penta- and...

Potential neuroleptic agents. 4. Chemistry, behavioral pharmacology, and inhibition of [3H]spiperone binding of 3,5-disubstituted N-[(1-ethyl-2-pyrrolidinyl)methyl]-6-methoxysalicylamides.

Science.gov (United States)

de Paulis, T; Kumar, Y; Johansson, L; Rämsby, S; Hall, H; Sällemark, M; Angeby-Möller, K; Ogren, S O

1986-01-01

A series of 3,5-disubstituted N-[(1-ethyl-2-pyrrolidinyl) methyl]-6-methoxysalicylamides was synthesized, starting from the 2,6-dimethoxybenzoic acids, by boron tribromide demethylation of the corresponding 3,5-disubstituted 2,6-dimethoxybenzamides and separation of the two positional isomers. The correct structure assignments were based on selective decoupling studies on their 13C NMR spectra. The salicylamide derivatives were tested for antidopamine activity in vivo by their ability to inhibit the apomorphine syndrome in the rat and in vitro by their ability to displace [3H]spiperone from striatal preparations of the rat brain. The activity seems to reside exclusively in the S enantiomer. Several compounds were considerably more potent than haloperidol, particularly those having an ethyl group in the 3-position and a halogen atom in the 5-position of the aromatic ring. The corresponding 5-alkyl-3-halogen-substituted compounds were much less active. A low acute toxicity was found for the most potent compounds. Some of the salicylamides displayed a 10-20-fold separation between the dose which blocks apomorphine-induced hyperactivity and that which blocks apomorphine-induced stereotypy. One compound, S-(-)-3,5-dichloro-N-[(1-ethyl-2-pyrrolidinyl) methyl]-6-methoxysalicylamide (raclopride, FLA 870) (13) had a stereotypy--hyperactivity separation more than twice that of sulpiride while being 100 times more potent in blocking the apomorphine effects. On this basis, 13 was selected for clinical trials against schizophrenia.

Photoisomerization of ethyl ferulate: A solution phase transient absorption study

Science.gov (United States)

Horbury, Michael D.; Baker, Lewis A.; Rodrigues, Natércia D. N.; Quan, Wen-Dong; Stavros, Vasilios G.

2017-04-01

Ethyl ferulate (ethyl 4-hydroxy-3-methoxycinnamate) is currently used as a sunscreening agent in commercial sunscreen blends. Recent time-resolved gas-phase measurements have demonstrated that it possesses long-lived (>ns) electronic excited states, counterintuitive to what one might anticipate for an effective sunscreening agent. In the present work, the photodynamics of ethyl ferulate in cyclohexane, are explored using time-resolved transient electronic absorption spectroscopy, upon photoexcitation to the 11ππ∗ and 21ππ∗ states. We demonstrate that ethyl ferulate undergoes efficient non-radiative decay to repopulate the electronic ground state, mediated by trans-cis isomerization. These results strongly suggest that even mild perturbations induced by a non-polar solvent, as may be found in a closer-to-market sunscreen blend, may contribute to our understanding of ethyl ferulate's role as a sunscreening agent.

Comparative studies with n-methyl-2-pyrrolidone and furfural as solvents for extraction of lube distillates

Energy Technology Data Exchange (ETDEWEB)

Krishna, R.; Singh, H.; Kishore, K.; Choudhary, G.S.; Kaushik, R.S.

Solvent extraction of spindle raw lube distillate from Oman crude using n-methyl pyrrolidone (NMP) containing 1.5 wt.% water has been studied using a six-stage all-glass mixer-settler. Results of three operating temperatures with NMP are reported. A 65-55/sup 0/C extraction temperature appears to be most appropriate for this stock. Data obtained at this temperature have been compared with those for furfural on the basis of phase boundary curves, extraction and lube refining indices and selectivity. Comparison of the results shows NMP to be more selective as far as raffinate yield is concerned. It requires lower operating solvent-to-feed ratios and lower temperatures. 14 refs.

Optical anisotropy, molecular orientations, and internal stresses in thin sulfonated poly(ether ether ketone) films

NARCIS (Netherlands)

Koziara, B.T.; Nijmeijer, K.; Benes, N.E.

2015-01-01

The thickness, the refractive index, and the optical anisotropy of thin sulfonated poly(ether ether ketone) films, prepared by spin-coating or solvent deposition, have been investigated with spectroscopic ellipsometry. For not too high polymer concentrations (≤5 wt%) and not too low spin speeds

Optical anisotropy, molecular orientations, and internal stresses in thin sulfonated poly(ether ether ketone) films

NARCIS (Netherlands)

Koziara, Beata; Nijmeijer, Dorothea C.; Benes, Nieck Edwin

2015-01-01

The thickness, the refractive index, and the optical anisotropy of thin sulfonated poly(ether ether ketone) films, prepared by spin-coating or solvent deposition, have been investigated with spectroscopic ellipsometry. For not too high polymer concentrations (B5 wt%) and not too low spin speeds

Quantification of fenoxaprop-p-ethyl herbicide in soil and vegetable samples by microwave-assisted solvent extraction and HPLC method

International Nuclear Information System (INIS)

Shahzad, F.U.N.; Shah, J.; Jan, M.R.; Muhammad, M.

2012-01-01

A simple HPLC procedure for the determination of fenoxaprop-p-ethyl herbicide in environmental samples is described. The chromatographic analysis was carried out by HPLC, on a C18 packed capillary column (4x4 mm,4.6 X 150 mm, 5mm particle size) with 20 macro l injection volume and UV detector at 280 nm. HPLC-grade acetonitrile and methanol were used as mobile phase with flow rate of 1mL min-1. Samples were spiked with amount between 5 - 20 micro g g-1 of herbicide and were isolated from samples by applying microwave assisted extraction (MASE) at ambient temperature. Percent recoveries were improved by optimizing solvent types, solvent volume, extraction temperature and time. Calibration curve range determined by HPLC was 0.5-16 micro g mL-1. The interaction of different variables for maximum % recovery response was checked by applying factorial design and was found to be in range of 91.22+-0.01-99.32+-0.01 with good precision (< 5% ). Application of this procedure to the analysis of herbicide in ester and acid form showed the effectiveness of the proposed approach. (author)

Optimization Study for Butanol Extraction from Butanol-Water Using Fatty Acid Methyl Ester (FAME) as Solvent

International Nuclear Information System (INIS)

Nurul Izzati Ab Rahim; Mohd Irfan Hatim Mohamed Dzahir; Wan Nurul Hidayah Wan Othman

2015-01-01

The oil crisis, warned the humanity's depends on oil was not sustainable and recently, there are plenty of renewable resources had been developed. Much attention has been given to the solvent extraction process to separate butanol from butanol-water mixture using fatty acid methyl ester (FAME) as a solvent. In this respect, the use of FAME as a green solvent which are locally available has greater potential for butanol extraction process. Therefore, an experimental work has been carried out to study its feasibility as a potential solvent. A single stage extraction process as performed to evaluate the ability to achieve optimal extract butanol. The extraction process was carried out to evaluate the distribution coefficient of butanol with the effects of other parameters such as reaction temperature (50-70 degree Celsius) and butanol-water mixture to solvent ratio (1:1, 1:1.5, 1:2). The constant parameter is the stirring speed (300 rpm). Response Surface Methodology (RSM) in conjunction with the Central Composition Design (CCD) as employed to statistically evaluate and optimize the butanol extraction process. It was found that the distribution coefficient has achieved an optimum level of 1.92 % at the following conditions: (i) butanol-water mixtures to solvent ratio (1:1.48) and (ii) reaction temperature (62.75 degree Celsius). (author)

Efficacy of scalp hair decontamination following exposure to vapours of sulphur mustard simulants 2-chloroethyl ethyl sulphide and methyl salicylate.

Science.gov (United States)

Spiandore, Marie; Piram, Anne; Lacoste, Alexandre; Prevost, Philippe; Maloni, Pascal; Torre, Franck; Asia, Laurence; Josse, Denis; Doumenq, Pierre

2017-04-01

Chemical warfare agents are an actual threat and victims' decontamination is a main concern when mass exposure occurs. Skin decontamination with current protocols has been widely documented, as well as surface decontamination. However, considering hair ability to trap chemicals in vapour phase, we investigated hair decontamination after exposure to sulphur mustard simulants methyl salicylate and 2-chloroethyl ethyl sulphide. Four decontamination protocols were tested on hair, combining showering and emergency decontamination (use of Fuller's earth or Reactive Skin Decontamination Lotion RSDL ® ). Both simulants were recovered from hair after treatment, but contents were significantly reduced (42-85% content allowance). Showering alone was the least efficient protocol. Concerning 2-chloroethyl ethyl sulphide, protocols did not display significant differences in decontamination efficacy. For MeS, use of emergency decontaminants significantly increased showering efficacy (10-20% rise), underlining their usefulness before thorough decontamination. Our results highlighted the need to extensively decontaminate hair after chemical exposure. Residual amounts after decontamination are challenging, as their release from hair could lead to health issues. Copyright © 2016. Published by Elsevier B.V.

Microwave-assisted extraction and accelerated solvent extraction with ethyl acetate-cyclohexane before determination of organochlorines in fish tissue by gas chromatography with electron-capture detection.

Science.gov (United States)

Weichbrodt, M; Vetter, W; Luckas, B

2000-01-01

Focused open-vessel microwave-assisted extraction (FOV-MAE), closed-vessel microwave-assisted extraction (CV-MAE), and accelerated solvent extraction (ASE) were used for extraction before determination of organochlorine compounds (polychlorinated biphenyls, DDT, toxaphene, chlordane, hexachlorobenzene, hexachlorocyclohexanes, and dieldrin) in cod liver and fish fillets. Wet samples were extracted without the time-consuming step of lyophilization or other sample-drying procedures. Extractions were performed with the solvent mixture ethyl acetate-cyclohexane (1 + 1, v/v), which allowed direct use of gel-permeation chromatography without solvent exchange. For FOV-MAE, the solvent mixture removed water from the sample matrix via azeotropic distillation. The status of water removal was controlled during extraction by measuring the temperature of the distillate. After water removal, the temperature of the distillate increased and the solvent mixture became less polar. Only the pure extraction solvent allowed quantitative extraction of the organochlorine compounds. For CV-MAE, water could not be separated during the extraction. For this reason, the extraction procedure for wet fish tissue required 2 extraction steps: the first for manual removal of coextracted water, and the second for quantitative extraction of the organochlorine compounds with the pure solvent. Therefore, CV-MAE is less convenient for samples with high water content. For ASE, water in the sample was bound with Na2SO4. The reproducibility for each technique was very good (relative standard deviation was typically <10%); the slightly varying levels were attributed to deviations during sample cleanup and the generally low levels.

Determining two-step control in heterogeneous catalytic reactions

Energy Technology Data Exchange (ETDEWEB)

Chakrabarty, T; Silveston, P L; Hudgins, R R

1979-10-01

The data by Thaller and Thodos on the sec.-butanol dehydrogenation to methyl ethyl ketone on brass catalyst indicated that a dual site surface reaction was rate-controlling below 575/sup 0/K and hydrogen desorption was rate-controlling above 616/sup 0/K (Vertical BarAIChE J.

Kinetics and thermodynamics of aqueous Cu(II) adsorption on heat ...

African Journals Online (AJOL)

This study investigated the kinetics and thermodynamics of copper(II) removal from aqueous solutions using spent bleaching earth (SBE). The spent bleaching earth, a waste material from edible oil processing industries, was reactivated by heat treatment at 370 oC after residual oil extraction in excess methyl-ethyl ketone.

9-Hydroxyfurodysinin-O-ethyl Lactone: A New Sesquiterpene Isolated from the Tropical Marine Sponge Dysidea arenaria

Directory of Open Access Journals (Sweden)

P. Karuso

2005-10-01

Full Text Available A new sesquiterpene, 9-hydroxyfurodysinin-O-ethyl lactone, has been isolated from a New Caledonian Dysidea arenaria, along with three known compounds. The possible incorporation of the ethyl ether from the extraction solvent is discussed.

Measurement and correlation of the solubility of 2,3,4,5-tetrabromothiophene in different solvents

International Nuclear Information System (INIS)

Wang, Kai; Hu, Yonghong; Yang, Wenge; Guo, Song; Shi, Ying

2012-01-01

Highlights: ► The solubility of tetrabromothiophene in different solvents was investigated. ► The modified Apelblat equation was more accurate than the van’t Hoff equation and the λh equation. ► Ethyl acetate showed the potential as a better recrystallization solvent to replace trichloromethane. ► The solution process in the selected solvents was endothermic and nonspontaneous. - Abstract: The solubility of 2,3,4,5-tetrabromothiophene were measured in methanol, ethanol, propan-1-ol, butan-1-ol, toluene, ethyl formate, ethyl acetate, trichloromethane and oxolane within the temperature range between 278.05 K and 325.15 K under atmospheric pressure by gravimetric method. The solubility of 2,3,4,5-tetrabromothiophene in those selected solvents increased with increasing temperature. The solubility data were correlated with the van’t Hoff equation, the modified Apelblat equation and the λh equation. The thermodynamic properties of the solution process, including the Gibbs energy, enthalpy, and entropy were calculated by the van’t Hoff analysis and the Gibbs equation. The experimental results showed that ethyl acetate had the potential as a better solvent in the re-crystallization process of 2,3,4,5-tetrabromothiophene.

Traceable atomic force microscopy of high-quality solvent-free crystals of [6,6]-phenyl-C61-butyric acid methyl ester

OpenAIRE

Lazzerini, GM; Paterno, GM; Tregnago, G; Treat, N; Stingelin, N; Yacoot, A; Cacialli, F

2016-01-01

We report high-resolution, traceable atomic force microscopymeasurements of high-quality, solvent-free single crystals of [6,6]-phenyl-C61-butyric acid methyl ester (PCBM). These were grown by drop-casting PCBM solutions onto the spectrosil substrates and by removing the residual solvent in a vacuum. A home-built atomic force microscope featuring a plane mirror differential optical interferometer, fiber-fed from a frequency-stabilized laser (emitting at 632.8???nm), was used to measure the cr...

Traceable atomic force microscopy of high-quality solvent-free crystals of [6,6]-phenyl-C-61-butyric acid methyl ester

OpenAIRE

Lazzerini, G. M.; Paterno, G. M.; Tregnago, G.; Treat, N.; Stingelin, N.; Yacoot, A.; Cacialli, F.

2016-01-01

We report high-resolution, traceable atomic force microscopymeasurements of high-quality, solvent-free single crystals of [6,6]-phenyl-C61-butyric acid methyl ester (PCBM). These were grown by drop-casting PCBM solutions onto the spectrosil substrates and by removing the residual solvent in a vacuum. A home-built atomic force microscope featuring a plane mirror differential optical interferometer, fiber-fed from a frequency-stabilized laser (emitting at 632.8 nm), was used to measure the crys...

Simultaneous exposure to ethyl benzene and noise : synergistic effects on outer hair cells

NARCIS (Netherlands)

Cappaert, N.L.M.; Klis, S.F.L.; Muijser, H.; Kulig, B.M.; Smoorenburg, G.F.

2001-01-01

The effects on hearing of simultaneous exposure to the ototoxic organic solvent ethyl benzene and broad-band noise were evaluated in rats. The effects of three ethyl benzene concentrations (0, 300 or 400 ppm) and three noise levels (95 or 105 dBlin SPL or background noise at 65 dBlin SPL) and all

Preparation of planar CH{sub 3}NH{sub 3}PbI{sub 3} thin films with controlled size using 1-ethyl-2-pyrrolidone as solvent

Energy Technology Data Exchange (ETDEWEB)

Hao, Qiuyan; Chu, Yixia [Engineering Laboratory of Functional Optoelectronic Crystalline Materials of Hebei Province, School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300132 (China); Zheng, Xuerong [Key Laboratory of Advanced Ceramics and Machining Technology of Ministry of Education, School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Liu, Zhenya; Liang, Liming [Engineering Laboratory of Functional Optoelectronic Crystalline Materials of Hebei Province, School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300132 (China); Qi, Jiakun [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China); Zhang, Xin [Engineering Laboratory of Functional Optoelectronic Crystalline Materials of Hebei Province, School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300132 (China); Liu, Gang [School of Chemical Engineering, Hebei University of Technology, Tianjin 300132 (China); Liu, Hui, E-mail: liuhuihebut@163.com [Engineering Laboratory of Functional Optoelectronic Crystalline Materials of Hebei Province, School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300132 (China); Chen, Hongjian [Engineering Laboratory of Functional Optoelectronic Crystalline Materials of Hebei Province, School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300132 (China); Liu, Caichi, E-mail: ccliu@hebut.edu.cn [Engineering Laboratory of Functional Optoelectronic Crystalline Materials of Hebei Province, School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300132 (China)

2016-06-25

Recently, planar perovskite solar cells based on CH{sub 3}NH{sub 3}PbI{sub 3} have attracted many researcher's interest due to their unique advantages such as simple cell architecture, easy fabrication and potential multijunction construction comparing to the initial mesoporous structure. However, the preparation of planar perovskite films with high quality is still in challenge. In this paper, we developed a vapor-assisted solution process using a novel and green solvent of 1-Ethyl-2-pyrrolidone (NEP) instead of the traditional N, N-dimethylformamide (DMF) to construct a high-quality perovskite CH{sub 3}NH{sub 3}PbI{sub 3} thin film with pure phase, high compactness, small surface roughness and controlled size. The phase evolution and growth mechanism of the perovskite films are also discussed. Utilizing the NEP of low volatility and moderate boiling point as solvent, we dried the PbI{sub 2}-NEP precursor films at different temperature under vacuum and then obtained PbI{sub 2} thin films with different crystalline degree from amorphous to highly crystalline. The perovskite films with crystal size ranged from hundreds of nanometers to several micrometers can be prepared by reacting the PbI{sub 2} films of different crystalline degree with CH{sub 3}NH{sub 3}I vapor. Moreover, planar-structured solar cells combining the perovskite film with TiO{sub 2} and spiro-OMeTAD as the electron and holes transporting layer achieves a power conversion efficiency of 10.2%. - Highlights: • A novel and green solvent of 1-Ethyl-2-pyrrolidone (NEP) was used to construct high-quality perovskite CH{sub 3}NH{sub 3}PbI{sub 3} thin film. • The CH{sub 3}NH{sub 3}PbI{sub 3} grain with different sizes ranged from hundreds of nanometers to several micrometers can be obtained. • Planar-structured perovskite CH{sub 3}NH{sub 3}PbI{sub 3} solar cells using NEP as solvent achieves a power conversion efficiency of 10.2%.

Demonstrate a Low Biochemical Oxygen Demand Aircraft Deicing Fluid

Science.gov (United States)

2013-03-04

slipperiness when walking or sliding shoes on pavement . Fluid was observed to lead to significant slipperiness FAIL Fluid has no impact on flight...of the specimens was ground to a 32 micro -inch (µin) finish, wiped clean with methyl ethyl ketone (MEK) and weighed to the nearest milligram (mg) on

Thermodynamic equilibrium of hydroxyacetic acid in pure and binary solvent systems

International Nuclear Information System (INIS)

Huang, Qiaoyin; Xie, Chuang; Li, Yang; Su, Nannan; Lou, Yajing; Hu, Xiaoxue; Wang, Yongli; Bao, Ying; Hou, Baohong

2017-01-01

Highlights: • Solubility of hydroxyacetic acid in mono-solvents and binary solvent mixtures was measured. • Modified Apelblat, NRTL and Wilson model were used to correlate the solubility data in pure solvents. • CNIBS/R-K and Jouyban-Acree model were used to correlate the solubility in binary solvent mixtures. • The mixing properties were calculated based on the NRTL model. - Abstract: The solubility of hydroxyacetic acid in five pure organic solvents and two binary solvent mixtures were experimentally measured from 273.15 K to 313.15 K at atmospheric pressure (p = 0.1 MPa) by using a dynamic method. The order of solubility in pure organic solvents is ethanol > isopropanol > n-butanol > acetonitrile > ethyl acetate within the investigated temperature range, except for temperature lower than 278 K where the solubility of HA in ethyl acetate is slightly larger than that in acetonitrile. Furthermore, the solubility data in pure solvents were correlated with the modified Apelblat model, NRTL model, and Wilson model and that in the binary solvents mixtures were fitted to the CNIBS/R-K model and Jouyban-Acree model. Finally, the mixing thermodynamic properties of hydroxyacetic acid in pure and binary solvent systems were calculated and discussed.

B2O3/Al2O3 as a new, highly efficient and reusable heterogeneous catalyst for the selective synthesis of β-enamino ketones and esters under solvent-free conditions

International Nuclear Information System (INIS)

Chen, Jiu-Xi; Gao, Wen-Xia; Jin, Hui-Le; Ding, Jin-Chang; Wu, Hua-Yue

2010-01-01

Boron oxide adsorbed on alumina (B 2 O 3 /Al 2 O 3 ) has been found to be a new and highly efficient heterogeneous catalyst for the synthesis of β-enamino ketones and esters by the enamination of various primary and secondary amines with β-dicarbonyl compounds under solvent-free conditions. The important features of this methodology are broad substrate scope, high yield, no requirement of metal catalysts, high regio- and chemoselectivity and environmental friendliness. In addition, the catalyst could be recovered easily after the reactions and reused without evident loss of reactivity. (author)

Cooling crystallization of Indomethacin from different organic solvents

DEFF Research Database (Denmark)

Malwade, Chandrakant Ramkrishna; Qu, Haiyan

, 25, 35, and 45 °C. The solvents with varying polarities (ethanol, methanol, ethyl acetate, acetone, acetonitrile, and dichloromethane) were used for solubility measurement. Maximum solubility of IMC was observed in acetone, while acetonitrile showed the lowest solubility. Solid phase analysis...... of excess solute with XRPD and Raman spectroscopy confirmed formation of IMC solvate in acetone, methanol and dichloromethane at 15 °C. Based on solubility of IMC, the solvents ethanol, ethyl acetate, acetone, and dichloromethane were selected for crystallization experiments. Nucleation kinetics of IMC...... in selected solvents was investigated through the measurement of induction time at 5 °C and 15 °C. Longer induction times were observed for IMC in ethanol at both temperatures compared to the one in acetone. Metastable α form of IMC was obtained from ethanol, while solvate of IMC was produced from acetone....

Morphology and performance of poly(2-methoxy-5-(20-ethyl-hexyloxy)-p-phenylenevinylene) (MEH-PPV) : (6,6)-phenyl-C61-butyric acid methyl ester (PCBM) based polymer solar cells

NARCIS (Netherlands)

Liu, L.J.; Bavel, van S.S.; Wen, S.P.; Yang, X.N.; Loos, J.

2013-01-01

Polymer solar cells were fabricated based on composite films of poly(2-methoxy-5-(2-ethyl-hexyloxy)-1,4-phenylenevinylene) (MEH-PPV):fullerene derivative (6,6)-phenyl-C61-butyric acid methyl ester (PCBM) with weight blend ratio of 1:3, 1:4 and 1:5, spin-coated from chloroform (CF), chlorobenzene

Organic solvents from sugar cane molasses

Energy Technology Data Exchange (ETDEWEB)

Oeser, H

1970-01-01

The production of organic solvents by fermentation of low priced cane molasses is discussed. Processes described and illustrated in detail include the production of acetone, butanol, ethanol, acetic acid, ethyl acetate and butyl acetate.

Radiation effects on polyacetylenes having substituents

International Nuclear Information System (INIS)

Higashimura, Toshinobu; Tang, Ben-Zhong; Masuda, Toshio; Yamaoka, Hitoshi; Matsuyama, Tomochika.

1985-01-01

Effects of γ-ray irradiation on high molecular weight polyacetylenes with various substituents were studied in air and in vacuum. The molecular weights of polymers from aliphatic disubstituted acetylenes (2-octyne and 2-decyne) remarkably reduced with irradiation in air. Their G values for chain scission in air were as high as 3 - 12, whereas no degradation occurred in vacuum. The degraded polymers contain carbonyl and hydroxyl groups, and are soluble in polar solvents such as methyl ethyl ketone and acetone. In contrast, polymers of aromatic disubstituted acetylenes (1-phenyl-1-propyne and 1-chloro-2-phenylacetylene) hardly degraded in air even with irradiation up to 40 Mrad. The degradation behavior of poly(t-butylacetylene) was intermediate between those of the above aliphatic and aromatic polymers. Thus the radiolysis of polyacetylenes was found to be greatly dependent on the kind of substituents. (author)

Reinvestigation of the radiopharmaceutical production of radioiodinated long-chain fatty acids. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

El-Shaboury, G; El-Kolaly, M T; Raieh, M [Labelled Compounds Department, Hot Laboratories Center, Atomic Energy Authority, Cairo (Egypt)

1996-03-01

An improved and simple radiopharmaceutical production technique for radioiodination of {omega} - (Br) or (I) fatty acids ({omega}) - Br or I-(C H{sub 2}){sub n} Co{sub 2} H, where n = 16 to 17 with Na{sup 13I} for myocardial imaging study is described. The technique of production is reported here based on an isotope or non - isotopic exchange reaction between the inactive halogenated fatty acids and lyophilized ethanolic solution of Na{sup 131} I (previously dispensed in 0.02 M NaOH solution) at 80 Degree C within 30 min in absolute ethanol (dehydrated and redistill at 78.5 to 80 degree C over nitrobenzene b.p. 208 to 212 degree C). Although considerable radiochemical yields have been obtained using a wide variety of organic solvents as an isotropic or non-isotropic exchange media such as acetone, methyl ethyl ketone, benzene as well as di-n-propyl ketone; certain problems due to the evaporation of these solvents during the process of purification have been observed. These problems were completely avoided by the initial dissolution of the reactants in dehydrated ethyl alcohol which facilitate direct dispensing of the final radioiodinated acids in diluted human serum albumen without any decomposition. Basically, following the radioiodination process the radioiodinated fatty acids ethanolic solution is passed through out an AgCl-impregnated filter to remove the untreated inorganic radioiodine (2 to 5%). The final pure solution (containing over 99.o% radioiodinated pure fatty acids) is dispensed in human serum albumen (4%), and then sterilized by passing it through 0.22 mum milli pore bacterial filter. The technique is being applied for the radiopharmaceutical production of radioiodinated-phenyl long-chain fatty acids such as iodo phenoxy-, and iodobenzamido-heptadecanoic acids. 3 figs.

Reinvestigation of the radiopharmaceutical production of radioiodinated long-chain fatty acids. Vol. 3

International Nuclear Information System (INIS)

El-Shaboury, G.; El-Kolaly, M.T.; Raieh, M.

1996-01-01

An improved and simple radiopharmaceutical production technique for radioiodination of ω - (Br) or (I) fatty acids (ω) - Br or I-(C H 2 ) n Co 2 H, where n = 16 to 17 with Na 13I for myocardial imaging study is described. The technique of production is reported here based on an isotope or non - isotopic exchange reaction between the inactive halogenated fatty acids and lyophilized ethanolic solution of Na 131 I (previously dispensed in 0.02 M NaOH solution) at 80 Degree C within 30 min in absolute ethanol (dehydrated and redistill at 78.5 to 80 degree C over nitrobenzene b.p. 208 to 212 degree C). Although considerable radiochemical yields have been obtained using a wide variety of organic solvents as an isotropic or non-isotropic exchange media such as acetone, methyl ethyl ketone, benzene as well as di-n-propyl ketone; certain problems due to the evaporation of these solvents during the process of purification have been observed. These problems were completely avoided by the initial dissolution of the reactants in dehydrated ethyl alcohol which facilitate direct dispensing of the final radioiodinated acids in diluted human serum albumen without any decomposition. Basically, following the radioiodination process the radioiodinated fatty acids ethanolic solution is passed through out an AgCl-impregnated filter to remove the untreated inorganic radioiodine (2 to 5%). The final pure solution (containing over 99.o% radioiodinated pure fatty acids) is dispensed in human serum albumen (4%), and then sterilized by passing it through 0.22 mum milli pore bacterial filter. The technique is being applied for the radiopharmaceutical production of radioiodinated-phenyl long-chain fatty acids such as iodo phenoxy-, and iodobenzamido-heptadecanoic acids. 3 figs

Supercritical antisolvent co-precipitation of rifampicin and ethyl cellulose

CSIR Research Space (South Africa)

Djerafi, R

2017-05-01

Full Text Available . Using the solvent mixture, co-precipitates with particle sizes ranging between 190 and 230 nm were obtained with drug loading and drug precipitation yield from respectively 8.5 to 38.5 and 42.4 to 77.2% when decreasing the ethyl cellulose...

Effect of various solvents on the viscosity-average molecular weight of poly (vinyl acetate)

International Nuclear Information System (INIS)

Rehman, W.U.; But, M.A.; Chughtai, A.; Jamil, T.; Sattar, A.

2006-01-01

Solution polymerization of Vinyl Acetate was carried out in various solvents (benzene, toluene, ethyl acetate, acetonitrile). Dilute solution viscometry was used to determine the viscosity-average molecular weight of the resulting Poly (Vinyl Acetate) (PV Ac) in each case. The viscosity-average molecular weight (M,J of PVAc was found to increase in the order benzene < toluene < ethyl acetate < acetonitrile, It was concluded that under the same reaction conditions (polymerization time, initiator quantity, solvent/monomer ratio, temperature), acetonitrile served as the best solvent for solution. polymerization of Vinyl Acetate monomer. (author)

Author Details

African Journals Online (AJOL)

van Heerden, PDR. Vol 47, No 5 (1973) - Articles Digital Data Processing of Images Abstract PDF · Vol 47, No 5 (1973) - Articles A Simple Automated System for the Routine Production of 99mTc by Methyl-Ethyl-Ketone Extraction Abstract PDF. ISSN: 0256-95749. AJOL African Journals Online. HOW TO USE AJOL.

Investigation of attractive and repulsive interactions associated with ketones in supercritical CO2, based on Raman spectroscopy and theoretical calculations.

Science.gov (United States)

Kajiya, Daisuke; Saitow, Ken-ichi

2013-08-07

Carbonyl compounds are solutes that are highly soluble in supercritical CO2 (scCO2). Their solubility governs the efficiency of chemical reactions, and is significantly increased by changing a chromophore. To effectively use scCO2 as solvent, it is crucial to understand the high solubility of carbonyl compounds, the solvation structure, and the solute-solvent intermolecular interactions. We report Raman spectroscopic data, for three prototypical ketones dissolved in scCO2, and four theoretical analyses. The vibrational Raman spectra of the C=O stretching modes of ketones (acetone, acetophenone, and benzophenone) were measured in scCO2 along the reduced temperature Tr = T∕Tc = 1.02 isotherm as a function of the reduced density ρr = ρ∕ρc in the range 0.05-1.5. The peak frequencies of the C=O stretching modes shifted toward lower energies as the fluid density increased. The density dependence was analyzed by using perturbed hard-sphere theory, and the shift was decomposed into attractive and repulsive energy components. The attractive energy between the ketones and CO2 was up to nine times higher than the repulsive energy, and its magnitude increased in the following order: acetone attractive energy and optimized the relative configuration between each solute and CO2. According to theoretical calculations for the dispersion energy, the dipole-induced-dipole interaction energy, and the frequency shift due to their interactions, the experimentally determined attractive energy differences in the three solutes were attributed to the dispersion energies that depended on a chromophore attached to the carbonyl groups. It was found that the major intermolecular interaction with the attractive shift varied from dipole-induced dipole to dispersion depending on the chromophore in the ketones in scCO2. As the common conclusion for the Raman spectral measurements and the four theoretical calculations, solute polarizability, modified by the chromophore, was at the core of

Synthesis and characterization of Ni0.7Zn0.3Fe2O4 ferrospinel: performance evaluation for methyl and ethyl esterification

International Nuclear Information System (INIS)

Mapossa, A.B.; Dantas, J.; Diniz, V.C.S.; Costa, A.C.F.M.; Silva, M.R.; Kiminami, R.H.G.A.

2017-01-01

Ni 0.7 Zn 0.3 Fe 2 O 4 ferrospinel was synthesized by combustion and its catalytic performance in methyl and ethyl esterification of the soybean oil was investigated. The samples were characterized by X-ray diffraction, Rietveld refinement analysis, energy dispersive X-ray fluorescence spectroscopy, Fourier transform infrared spectroscopy, textural analysis, scanning electron microscopy, density by picnometry, particle size analysis, thermogravimetric analysis, magnetic measurements, and catalytic tests. The synthesis was efficient resulting in a ferrospinel with single phase Ni 0.7 Zn 0.3 Fe 2 O 4 with crystallite size of 20 nm, high surface area (86 m 2 /g) and saturation magnetization of 18 emu/g. The ferrospinel had promising catalytic activity in both reaction conditions studied, being more active in the conversion of soybean oil to biodiesel in methyl esterification with an average conversion of 93.9±2.8%. (author)

Ketone bodies in epilepsy.

Science.gov (United States)

McNally, Melanie A; Hartman, Adam L

2012-04-01

Seizures that are resistant to standard medications remain a major clinical problem. One underutilized option for patients with medication-resistant seizures is the high-fat, low-carbohydrate ketogenic diet. The diet received its name based on the observation that patients consuming this diet produce ketone bodies (e.g., acetoacetate, β-hydroxybutyrate, and acetone). Although the exact mechanisms of the diet are unknown, ketone bodies have been hypothesized to contribute to the anticonvulsant and antiepileptic effects. In this review, anticonvulsant properties of ketone bodies and the ketogenic diet are discussed (including GABAergic and glutamatergic effects). Because of the importance of ketone body metabolism in the early stages of life, the effects of ketone bodies on developing neurons in vitro also are discussed. Understanding how ketone bodies exert their effects will help optimize their use in treating epilepsy and other neurological disorders. © 2012 The Authors. Journal of Neurochemistry © 2012 International Society for Neurochemistry.

IDENTIFIKASI CHARACTER IMPACT ODORANTS BUAH KAWISTA (Feronia Limonia [Identification of Character Impact Odorants of Wood Apple Fruit (Feronia Limonia

Directory of Open Access Journals (Sweden)

Anton Apriyantono1

2004-04-01

Full Text Available The volatiles of the kawista fruit (wood apple were analyzed by gas chromatography (GC and a combined gas chromatography-mass spectrometer (GC-MS. Character impact odorants of the fruits were systematically characterized by aroma extract dilution analysis (AEDA with GC-Olfactometry (GC-O. A total of 75 compounds were identified, including 28 esters, 11 alcohols, 10 aldehydes, 1 acetal, 10 ketones, 4 lactones, 1 heterocyclic, 4 aliphatic hydrocarbons, 1 furan and 5 acids. However, only 44 volatiles were detected by GC-O. Among these, compounds with the most impact were ethyl butyrate (fruity, sweet, banan-likeand methyl butyrate (fruit, sour with a flavor dilution factor of 256 and 64, respectively. Based on AEDA results, butyric acid, 3-mathyl valeric acid, 1-octen-3-ol, pentyl isobutyrate, 2-ethyl hexanoic acid, ethyl octanoate, gamma-decalactone, 2,3-pentanedione, 3-octanone, 5-methyl-3-heptanone, 9-methyl-5-undecene and (E-2-hexenyl butyrate seem to contribute to kawista fruit flavor

Synthesis and crystal structures of 2-methyl-4-aryl-5-oxo-5H-indeno [1,2-b] pyridine carboxylate derivatives

DEFF Research Database (Denmark)

Pandian, Ramesh; Naushad, Edayadulla; Vijayakumar, Vinodhkumar

2014-01-01

pyridine derivatives through oxidation. Consequently, the interest in this aromatization reaction, investigation of a wide range of 1, 4-DHPs continues to attract the attention of researchers. Herein, we report the preparation of pyridine derivatives and the crystal structures determined by X......-ray crystallographic methods.Results: The crystal structures and conformational studies of two organic compounds, namely ethyl 2-methyl-4-phenyl-5-oxo-5H-indeno [1,2-b] pyridine-3-carboxylate (I) and ethyl 2-methyl-4-(4 chlorophenyl)-5-oxo-5H-indeno [1,2-b] pyridine-3-carboxylate (II) are reported. The terminal ethyl......) dimer running along 011 direction.Conclusion: The crystal structures ethyl 2-methyl-4-phenyl-5-oxo-5H-indeno [1,2-b] pyridine-3-carboxylate and ethyl 2-methyl-4-(4 chlorophenyl)-5-oxo-5H-indeno [1,2-b] pyridine-3-carboxylate have been investigated in detail. The terminal ethyl group of compound I...

Can green solvents be alternatives for thermal stabilization of collagen?

Science.gov (United States)

Mehta, Ami; Rao, J Raghava; Fathima, Nishter Nishad

2014-08-01

"Go Green" campaign is gaining light for various industrial applications where water consumption needs to be reduced. To resolve this, industries have adopted usage of green, organic solvents, as an alternative to water. For leather making, tanning industry consumes gallons of water. Therefore, for adopting green solvents in leather making, it is necessary to evaluate its influence on type I collagen, the major protein present in the skin matrix. The thermal stability of collagen from rat tail tendon fiber (RTT) treated with seven green solvents namely, ethanol, ethyl lactate, ethyl acetate, propylene carbonate, propylene glycol, polyethylene glycol-200 and heptane was determined using differential scanning calorimetry (DSC). Crosslinking efficiency of basic chromium sulfate and wattle on RTT in green solvents was determined. DSC thermograms show increase in thermal stability of RTT collagen against heat with green solvents (>78°C) compared to water (63°C). In the presence of crosslinkers, RTT demonstrated thermal stability >100°C in some green solvents, resulting in increased intermolecular forces between collagen, solvent and crosslinkers. The significant improvement in thermal stability of collagen potentiates the capability of green solvents as an alternative for water. Copyright © 2014 Elsevier B.V. All rights reserved.

Exploration of ethyl anthranilate-loaded monolithic matrix-type prophylactic polymeric patch

Directory of Open Access Journals (Sweden)

Johirul Islam

2017-10-01

Full Text Available Compromised stability of pharmaceutical formulations loaded with volatiles is a serious problem associated with devices designed to deliver volatile compounds. The present study has been focused to evaluate the stability potential of matrix-type polymeric patches composed of volatile ethyl anthranilate for prophylaxis against vector-borne diseases. Ethyl anthranilate-loaded matrix-type polymeric patches were fabricated by solvent evaporation method on an impermeable backing membrane and attached to temporary release liners. Stability testing of the polymeric patches was performed as per the International Conference on Harmonization (ICH guidelines for 6 months under accelerated conditions. In addition, the quantification of residual solvents was also performed as per the ICH guidelines. After conducting the stability studies for 6 months, the optimized patches showed the best possible results with respect to uniformity of drug content, physical appearance, and other analytical parameters. Furthermore, the amount of residual solvent was found well below the accepted limit. Thus, the present report outlined the analytical parameters to be evaluated to ensure the stability of a certain devices consisting of volatile compounds.

Organic Solvent-Tolerant Marine Microorganisms as Catalysts for Kinetic Resolution of Cyclic β-Hydroxy Ketones

NARCIS (Netherlands)

Chen, B.; Liu, Hui; Zeferino Ribeiro De Souza, F.; Liu, Lan

2017-01-01

Chiral cyclic β-hydroxy ketones represent key motifs in the production of natural products of biological interest. Although the molecules are structurally simple, they require cumbersome synthetic steps to get access to them and their synthesis remains a challenge in organic chemistry. In this

Lignin Structure and Aggregation Behavior in a Two-Component Ionic Liquid Solvent System

Directory of Open Access Journals (Sweden)

Susanne Bylin

2014-08-01

Full Text Available Ionic liquids are of potential interest in the processing of lignocellulosic biomass. In this study, the ionic liquid co-solvent system of 1-methylimidazole (MIM and 1-ethyl-3-methyl-imidazolium acetate (EMIMAc was used to solvate LignoBoost lignin fractionated from black liquor obtained from a kraft paper mill. Lignin ethanol-precipitated (LEP and ethanol-soluble (LES fractions were characterized via gel permeation chromatography (GPC and 13C- and 31P-nuclear magnetic resonance spectroscopy (NMR to determine structural characteristics and their relationship to polymer solubility in the system. Polymer integrity and solubility were optimal at ~20% lignin loading (w/w. Results showed that LEPs were generally of higher apparent molecular weight (Mw and enriched with condensed/aliphatic ether linkages and aliphatic hydroxyls. The LESs had a lower apparent Mw and were enriched with carboxylic and phenolic groups. This newly gained knowledge on lignin fractionation and aggregation in the present solvent system provides future opportunities for tuning fractionation/extraction to suit a specific biomass-derived product, e.g., carbon fibers.

Cs2CO3-Initiated Trifluoro-Methylation of Chalcones and Ketones for Practical Synthesis of Trifluoromethylated Tertiary Silyl Ethers

Directory of Open Access Journals (Sweden)

Cheng Dong

2017-05-01

Full Text Available It was found that 1,2-trifluoromethylation reactions of ketones, enones, and aldehydes were easily accomplished using the Prakash reagent in the presence of catalytic amounts of cesium carbonate, which represents an experimentally convenient, atom-economic process for this anionic trifluoromethylation of non-enolisable aldehydes and ketones.

Laboratory Tests to Determine the Chemical and Physical Characteristics of Propellant-Solvent-Fuel Oil Mixtures

Science.gov (United States)

1990-02-01

isocyanates and many heterocyclic alcohols and ketones such as furfural and camphor also possess some I solvent power for nitrocellulose. Amines...34Estimation of Solvent Power by the Dilution-Ratio Method," J. Appl. Chem. (London) 7, 332 (1957). U R.P. Teulings, "A Multivariable Study of the Adsorption of

Stabilizing Effects of Deep Eutectic Solvents on Alcohol Dehydrogenase Mediated Systems

OpenAIRE

Fatima Zohra Ibn Majdoub Hassani; Ivan Lavandera; Joseph Kreit

2016-01-01

This study explored the effects of different organic solvents, temperature, and the amount of glycerol on the alcohol dehydrogenase (ADH)-catalysed stereoselective reduction of different ketones. These conversions were then analyzed by gas chromatography. It was found that when the amount of deep eutectic solvents (DES) increases, it can improve the stereoselectivity of the enzyme although reducing its ability to convert the substrate into the corresponding alcohol. Moreover, glycerol was fou...

Methyl vinyl ketone, a toxic ingredient in cigarette smoke extract, modifies glutathione in mouse melanoma cells.

Science.gov (United States)

Horiyama, Shizuyo; Takahashi, Yuta; Hatai, Mayuko; Honda, Chie; Suwa, Kiyoko; Ichikawa, Atsushi; Yoshikawa, Noriko; Nakamura, Kazuki; Kunitomo, Masaru; Date, Sachiko; Masujima, Tsutomu; Takayama, Mitsuo

2014-01-01

Cigarette smoke contains many harmful chemicals, which contribute to the pathogenesis of smoking-related diseases such as chronic obstructive pulmonary disease, cancer and cardiovascular disease. The cytotoxicity of cigarette smoke is well documented, but the definitive mechanism behind its toxicity remains unknown. Ingredients in cigarette smoke are known to deplete intracellular glutathione (GSH), the most abundant cellular thiol antioxidant, and to cause oxidative stress. In the present study, we investigated the mechanism of cigarette smoke extract (CSE)-induced cytotoxicity in B16-BL6 mouse melanoma (B16-BL6) cells using liquid chromatography-tandem mass spectrometry. CSE and ingredients in cigarette smoke, methyl vinyl ketone (MVK) and crotonaldehyde (CA), reduced cell viability in a concentration-dependent manner. Also, CSE and the ingredients (m/z 70, each) irreversibly reacted with GSH (m/z 308) to form GSH adducts (m/z 378) in cells and considerably decreased cellular GSH levels at concentrations that do not cause cell death. Mass spectral data showed that the major product formed in cells exposed to CSE was the GSH-MVK adduct via Michael-addition and was not the GSH-CA adduct. These results indicate that MVK included in CSE reacts with GSH in cells to form the GSH-MVK adduct, and thus a possible reason for CSE-induced cytotoxicity is a decrease in intracellular GSH levels.

Use of ethyl lactate to extract bioactive compounds from Cytisus scoparius: Comparison of pressurized liquid extraction and medium scale ambient temperature systems.

Science.gov (United States)

Lores, Marta; Pájaro, Marta; Álvarez-Casas, Marta; Domínguez, Jorge; García-Jares, Carmen

2015-08-01

An important trend in the extraction of chemical compounds is the application of new environmentally friendly, food grade solvents. Ethyl lactate (ethyl 2-hydroxypropanoate), produced by fermentation of carbohydrates, is miscible with both hydrophilic and hydrophobic compounds being a potentially good solvent for bioactive compounds. Despite its relatively wide use as a general solvent, the utilization of ethyl lactate as an extraction solvent has only recently been considered. Here, we evaluate the possible use of ethyl lactate to extract phenolic compounds from wild plants belonging to Cytisus scoparius, and we compare the characteristics of the extracts obtained by Pressurized Solvent Extraction (the total phenolics content, the antioxidant activity and the concentration of the major polyphenols) with those of other extracts obtained with methanol. In order to explore the industrial production of the ethyl lactate Cytisus extract, we also evaluate medium scale ambient temperature setups. The whole plant and the different parts (flowers, branches, and seed pods) were evaluated separately as potential sources of polyphenols. All extracts were analyzed by LC-MS/MS for accurate identification of the major polyphenols. Similar phenolic profiles were obtained when using ethyl lactate or methanol. The main bioactives found in the Cytisus extract were the non-flavonoid phenolic compounds caffeic and protocatechuic acids and 3,4-dihydroxybenzaldehyde; the flavonoids rutin, kaempferol and quercetin; the flavones chrysin, orientin and apigenin; and the alkaloid lupanine. Regarding the comparison of the extraction systems, although the performance of the PLE was much better than that of the ambient-temperature columns, the energy consumption was also much higher. Ethyl lactate has resulted an efficient extraction solvent for polyphenols from C. scoparius, yielding extracts with high levels of plant phenolics and antioxidant activity. The antimicrobial activity of these

Benchmarking Continuum Solvent Models for Keto-Enol Tautomerizations.

Science.gov (United States)

McCann, Billy W; McFarland, Stuart; Acevedo, Orlando

2015-08-13

Experimental free energies of tautomerization, ΔGT, were used to benchmark the gas-phase predictions of 17 different quantum mechanical methods and eight basis sets for seven keto-enol tautomer pairs dominated by their enolic form. The G4 method and M06/6-31+G(d,p) yielded the most accurate results, with mean absolute errors (MAE's) of 0.95 and 0.71 kcal/mol, respectively. Using these two theory levels, the solution-phase ΔGT values for 23 unique tautomer pairs composed of aliphatic ketones, β-dicarbonyls, and heterocycles were computed in multiple protic and aprotic solvents. The continuum solvation models, namely, polarizable continuum model (PCM), polarizable conductor calculation model (CPCM), and universal solvation model (SMD), gave relatively similar MAE's of ∼1.6-1.7 kcal/mol for G4 and ∼1.9-2.0 kcal/mol with M06/6-31+G(d,p). Partitioning the tautomer pairs into their respective molecular types, that is, aliphatic ketones, β-dicarbonyls, and heterocycles, and separating out the aqueous versus nonaqueous results finds G4/PCM utilizing the UA0 cavity to be the overall most accurate combination. Free energies of activation, ΔG(‡), for the base-catalyzed keto-enol interconversion of 2-nitrocyclohexanone were also computed using six bases and five solvents. The M06/6-31+G(d,p) reproduced the ΔG(‡) with MAE's of 1.5 and 1.8 kcal/mol using CPCM and SMD, respectively, for all combinations of base and solvent. That specific enolization was previously proposed to proceed via a concerted mechanism in less polar solvents but shift to a stepwise mechanism in more polar solvents. However, the current calculations suggest that the stepwise mechanism operates in all solvents.

A Comparative study on VOCs and aldehyde-ketone emissions from a spark Ignition vehicle fuelled on compressed natural gas and gasoline

International Nuclear Information System (INIS)

Shah, A.N.

2012-01-01

In this work, an experimental study was conducted on a spark ignition (SI) vehicle fuelled on compressed natural gas (CNG), and gasoline to compare the unregulated emissions such as volatile organic compounds (VOCs) and aldehyde-ketones or carbonyls. In the meantime, ozone forming potential (OFP) of pollutants was also calculated on the basis of their specific reactivity (SR). The vehicle was run on a chassis dynamometer following the Chinese National Standards test scheduled for light duty vehicle (LDV) emissions. According to the results, total aldehyde-ketones were increased by 39.4% due to the substantial increase in formaldehyde and acrolein + acetone emissions, while VOCs and BTEX (benzene, toluene, ethyl benzene, and xylene) reduced by 85.2 and 86% respectively, in case of CNG fuelled vehicle as compared to gasoline vehicle. Although total aldehyde-ketones were higher with CNG relative to gasoline, their SR was lower due decrease in acetaldehyde, propionaldehyde, crotonaldehyde, and methacrolein species having higher maximum incremental reactivity (MIR) values. The SR of VOCs and aldehyde-ketones emitted from CNG fuelled vehicle was decreased by above 10% and 32% respectively, owing to better physicochemical properties and more complete burning of CNG as compared to gasoline. (author)

Journal of Chemical Sciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Journal of Chemical Sciences; Volume 113; Issue 3 ... reaction with methyl vinyl ketone (MVK) and S-proline in the absence of solvents. ... Department of Organic Chemistry, University of Madras, Guindy Campus, Chennai 600 ...

Free radical detection by means of 212Pb mirrors

International Nuclear Information System (INIS)

Molera, M.J.; Gamboa, J. M.; Garcia Guijarro, E.

1961-01-01

Radicals have been detected at low temperatures (550-700 degree centigrade) in the thermal decomposition of dimethyl and methyl-ethyl-ketone by the Paneth method. the sensitivity of the method has been increased by the use of radioactive mirrors of PB 2 12. They have proved to detect one radical among 2.10 6 molecules. (Author) 18 refs

Molecular modeling study of agglomeration of [6,6]-phenyl-C61-butyric acid methyl ester in solvents.

Science.gov (United States)

Mortuza, S M; Banerjee, Soumik

2012-12-28

The molecular interactions between solvent and nanoparticles during photoactive layer formation in organic photovoltaic (OPV) cells influence the morphology of the photoactive layer and hence determine the power conversion efficiency. Prediction of optimal synthesis parameters in OPVs, such as choice of solvent, processing temperature, and nanoparticle concentration, requires fundamental understanding of the mechanisms that govern the agglomeration of nanoparticles in solvents. In this study, we used molecular dynamics simulations to simulate a commonly used organic nanoparticle, [6,6]-phenyl-C61-butyric acid methyl ester (PCBM), in various solvents to correlate solvent-nanoparticle interactions with the size of the agglomerate structure of PCBM. We analyzed the effects of concentration of PCBM and operating temperature on the molecular rearrangement and agglomeration of PCBM in three solvents: (i) toluene, (ii) indane, and (iii) toluene-indane mixture. We evaluated the agglomeration behavior of PCBM by determining sizes of the largest clusters of PCBM and the corresponding size distributions. To obtain further insight into the agglomerate structure of PCBMs, we evaluated radial distribution functions (RDFs) and coordination numbers of the various moieties of PCBMs with respect to solvent atoms as well as with respect to that of other PCBMs. Our simulations demonstrate that PCBMs form larger clusters in toluene while they are relatively dispersed in indane, which indicates the greater solubility of PCBM in indane than in toluene. In toluene-indane mixture, PCBMs are clustered to a greater extent than in indane and less than that in toluene. To correlate agglomerate size to nanoparticle-solvent interactions, we also evaluated the potential of mean force (PMF) of the fullerene moiety of PCBM in toluene and indane. Our results also show that the cluster size of PCBM molecules increases with the increase of concentration of PCBM and the processing temperature. To

Why are ionic liquid ions mainly associated in water? A Car-Parrinello study of 1-ethyl-3-methyl-imidazolium chloride water mixture

Science.gov (United States)

Spickermann, C.; Thar, J.; Lehmann, S. B. C.; Zahn, S.; Hunger, J.; Buchner, R.; Hunt, P. A.; Welton, T.; Kirchner, B.

2008-09-01

In this study we present the results of a first principles molecular dynamics simulation of a single 1-ethyl-3-methyl-imidazolium chloride [C2C1im][Cl] ion pair dissolved in 60 water molecules. We observe a preference of the in plane chloride coordination with respect to the cation ring plane as compared to the energetic slightly more demanding on top coordination. Evaluation of the different radial distribution functions demonstrates that the structure of the hydration shell around the ion pair differs significantly from bulk water and that no true ion pair dissociation in terms of completely autonomous solvation shells takes place on the timescale of the simulation. In addition, dipole moment distributions of the solvent in distinct solvation shells around different functional parts of the [C2C1im][Cl] ion pair are calculated from maximally localized Wannier functions. The analysis of these distributions gives evidence for a depolarization of water molecules close to the hydrophobic parts of the cation as well as close to the anion. Examination of the angular distribution of different OH(H2O )-X angles in turn shows a linear coordination of chloride accompanied by a tangential orientation of water molecules around the hydrophobic groups, being a typical feature of hydrophobic hydration. Based on these orientational aspects, a structural model for the obvious preference of ion pair association is developed, which justifies the associating behavior of solvated [C2C1im][Cl] ions in terms of an energetically favorable interface between the solvation shells of the anion and the hydrophobic parts of the cation.

High-performance ferroelectric memory based on phase-separated films of polymer blends

KAUST Repository

Khan, Yasser; Bhansali, Unnat Sampatraj; Almadhoun, Mahmoud N.; Odeh, Ihab N.; Cha, Dong Kyu; Alshareef, Husam N.

2013-01-01

High-performance polymer memory is fabricated using blends of ferroelectric poly(vinylidene-fluoride-trifluoroethylene) (P(VDF-TrFE)) and highly insulating poly(p-phenylene oxide) (PPO). The blend films spontaneously phase separate into amorphous PPO nanospheres embedded in a semicrystalline P(VDF-TrFE) matrix. Using low molecular weight PPO with high miscibility in a common solvent, i.e., methyl ethyl ketone, blend films are spin cast with extremely low roughness (Rrms ≈ 4.92 nm) and achieve nanoscale phase seperation (PPO domain size < 200 nm). These blend devices display highly improved ferroelectric and dielectric performance with low dielectric losses (<0.2 up to 1 MHz), enhanced thermal stability (up to ≈353 K), excellent fatigue endurance (80% retention after 106 cycles at 1 KHz) and high dielectric breakdown fields (≈360 MV/m). © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Principal Component Analysis Based Two-Dimensional (PCA-2D) Correlation Spectroscopy: PCA Denoising for 2D Correlation Spectroscopy

International Nuclear Information System (INIS)

Jung, Young Mee

2003-01-01

Principal component analysis based two-dimensional (PCA-2D) correlation analysis is applied to FTIR spectra of polystyrene/methyl ethyl ketone/toluene solution mixture during the solvent evaporation. Substantial amount of artificial noise were added to the experimental data to demonstrate the practical noise-suppressing benefit of PCA-2D technique. 2D correlation analysis of the reconstructed data matrix from PCA loading vectors and scores successfully extracted only the most important features of synchronicity and asynchronicity without interference from noise or insignificant minor components. 2D correlation spectra constructed with only one principal component yield strictly synchronous response with no discernible a asynchronous features, while those involving at least two or more principal components generated meaningful asynchronous 2D correlation spectra. Deliberate manipulation of the rank of the reconstructed data matrix, by choosing the appropriate number and type of PCs, yields potentially more refined 2D correlation spectra

High-performance ferroelectric memory based on phase-separated films of polymer blends

KAUST Repository

Khan, Yasser

2013-10-29

High-performance polymer memory is fabricated using blends of ferroelectric poly(vinylidene-fluoride-trifluoroethylene) (P(VDF-TrFE)) and highly insulating poly(p-phenylene oxide) (PPO). The blend films spontaneously phase separate into amorphous PPO nanospheres embedded in a semicrystalline P(VDF-TrFE) matrix. Using low molecular weight PPO with high miscibility in a common solvent, i.e., methyl ethyl ketone, blend films are spin cast with extremely low roughness (Rrms ≈ 4.92 nm) and achieve nanoscale phase seperation (PPO domain size < 200 nm). These blend devices display highly improved ferroelectric and dielectric performance with low dielectric losses (<0.2 up to 1 MHz), enhanced thermal stability (up to ≈353 K), excellent fatigue endurance (80% retention after 106 cycles at 1 KHz) and high dielectric breakdown fields (≈360 MV/m). © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ethyl cellulose microcapsules for protecting and controlled release of folic acid.

Science.gov (United States)

Prasertmanakit, Satit; Praphairaksit, Nalena; Chiangthong, Worawadee; Muangsin, Nongnuj

2009-01-01

Ethyl cellulose microcapsules were developed for use as a drug-delivery device for protecting folic acid from release and degradation in the undesirable environmental conditions of the stomach, whilst allowing its release in the intestinal tract to make it available for absorption. The controlled release folic acid-loaded ethyl cellulose microcapsules were prepared by oil-in-oil emulsion solvent evaporation using a mixed solvent system, consisting of a 9:1 (v/v) ratio of acetone:methanol and light liquid paraffin as the dispersed and continuous phase. Span 80 was used as the surfactant to stabilize the emulsion. Scanning electron microscopy revealed that the microcapsules had a spherical shape. However, the particulate properties and in vitro release profile depended on the concentrations of the ethyl cellulose, Span 80 emulsifier, sucrose (pore inducer), and folic acid. The average diameter of the microcapsules increased from 300 to 448 microm, whilst the folic acid release rate decreased from 52% to 40%, as the ethyl cellulose concentration was increased from 2.5% to 7.5% (w/v). Increasing the Span 80 concentration from 1% to 4% (v/v) decreased the average diameter of microcapsules from 300 to 141 microm and increased the folic acid release rate from 52% to 79%. The addition of 2.5-7.5% (w/v) of sucrose improved the folic acid release from the microcapsules. The entrapment efficiency was improved from 64% to 88% when the initial folic acid concentration was increased from 1 to 3 mg/ml.

Performance of an enzymatic packed bed reactor running on babassu oil to yield fatty ethyl esters (FAEE in a solvent-free system

Directory of Open Access Journals (Sweden)

Aline Simões

2015-06-01

Full Text Available The transesterification reaction of babassu oil with ethanol mediated by Burkholderia cepacia lipase immobilized on SiO2-PVA composite was assessed in a packed bed reactor running in the continuous mode. Experiments were performed in a solvent-free system at 50 °C. The performance of the reactor (14 mm ×210 mm was evaluated using babassu oil and ethanol at two molar ratios of 1:7 and 1:12, respectively, and operational limits in terms of substrate flow rate were determined. The system’s performance was quantified for different flow rates corresponding to space times between 7 and 13 h. Under each condition, the impact of the space time on the ethyl esters formation, the transesterification yield and productivity were determined. The oil to ethanol molar ratio was found as a critical parameter in the conversion of babassu oil into the correspondent ethyl esters. The highest transesterification yield of 96.0 ± 0.9% and productivity of 41.1 ± 1.6 mgester gcatalyst-1h-1 were achieved at the oil to ethanol molar ratio of 1:12 and for space times equal or higher than 11 h. Moreover, the immobilized lipase was found stable with respect to its catalytic characteristics, exhibiting a half-life of 32 d.

Solvent free hydroxylation of the methyl esters of Blighia unijugata seed oil in the presence of cetyltrimethylammonium permanganate

Directory of Open Access Journals (Sweden)

Adewuyi Adewale

2011-12-01

Full Text Available Abstract Extraction of oil from the seed of Blighia unijugata gave a yield of 50.82 ± 1.20% using hexane in a soxhlet extractor. The iodine and saponification values were 67.60 ± 0.80 g iodine/100 g and 239.20 ± 1.00 mg KOH/g respectively with C18:1 being the dominant fatty acid. Unsaturated methyl esters of Blighia unijugata which had been previously subjected to urea adduct complexation was used to synthesize methyl 9, 10-dihydroxyoctadecanoate via hydroxylation in the presence of cetyltrimethylammonium permanganate (CTAP. The reaction was monitored and confirmed using FTIR and GC-MS. This study has revealed that oxidation reaction of mono unsaturated bonds using CTAP could be achieved under solvent free condition.

Solvent extraction of gold(III) with 1-phenyl-3-methyl-4-trifluoroacetylpyrazolone-5

International Nuclear Information System (INIS)

Hasany, S.M.; Imtiaz Hanif

1978-01-01

A simple, rapid and selective separation procedure of gold based on its extraction with 1-phenyl-3-methyl-4-trifluoroacetylpyrazolone-5 has been developed. The dependence of the distribution ratio of gold on the pH of aqueous solutions, concentration of hydrochloric, nitric and perchloric acids and the organic solvents has been investigated. Decontamination factors for a number of metal ions with respect to gold are reported. Excellent separation of gold is obtained from many elements including noble metals. Citrate, cyanide, iodide, thiosulfate and thiourea completely mask gold, whereas oxalate does not interfere. Solutions of 1M HCl, 0.2M KCN, and the buffer of pH 0.8 readily strip gold from the organic phase. Some useful analytical applications of this procedure are discussed. (author)

Improved Logistics for Chemical and Biologics Decontamination for Deployed Military

Science.gov (United States)

2012-07-01

miscible with ethanolamine (the main solvent of the lanthanide neutralization system) include tetrahydrofuran (THF), ethyl lactate, dimethylsulfoxide ...55 Preliminary Co- Solvent Testing Solvent –Rubber Interaction Observations NMP – 1-Methyl-2-pyrrolidone THF – Tetrahydrofuran DMSO ...salts and/or the incorporation of a variety of components such as co- solvents , emulsifiers, and other additives to improve their neutralization

Cyclodextrin ketones as oxidation catalysts: investigation of bridged derivatives

DEFF Research Database (Denmark)

Fenger, Thomas Hauch; Marinescu, Lavinia; Bols, Mikael

2009-01-01

A series of alpha-cyclodextrin derivatives containing a 3, 4 or 5 membered ether-linked bridge between the 6A and 6D oxygen atoms, with and without a ketone, were prepared. The synthesis used perbenzylated alpha-cyclodextrin A,D-diol as a starting material upon which O-alkylation and further modi...... derivatives were also made. The 6A,6D-di-O-(propa-2-on-1,3-diyl)-6C,6F-di-O-methyl and di-O-pivaloyl derivatives were also prepared. The new compounds were analysed for catalysis of the oxidation of amines and alcohols....

Investigation of the Use of a Bio-Derived Solvent for Non-Solvent-Induced Phase Separation (NIPS Fabrication of Polysulfone Membranes

Directory of Open Access Journals (Sweden)

Xiaobo Dong

2018-05-01

Full Text Available Organic solvents, such as N-methyl-2-pyrrolidone (NMP and dimethylacetamide (DMAc, have been traditionally used to fabricate polymeric membranes. These solvents may have a negative impact on the environment and human health; therefore, using renewable solvents derived from biomass is of great interest to make membrane fabrication sustainable. Methyl-5-(dimethylamino-2-methyl-5-oxopentanoate (Rhodiasolv PolarClean is a bio-derived, biodegradable, nonflammable and nonvolatile solvent. Polysulfone is a commonly used polymer to fabricate membranes due to its thermal stability, strong mechanical strength and good chemical resistance. From cloud point curves, PolarClean showed potential to be a solvent for polysulfone. Membranes prepared with PolarClean were investigated in terms of their morphology, porosity, water permeability and protein rejection, and were compared to membranes prepared with traditional solvents. The pores of polysulfone/PolarClean membranes were sponge-like, and the membranes displayed higher water flux values (176.0 ± 8.8 LMH along with slightly higher solute rejection (99.0 ± 0.51%. On the other hand, PSf/DMAc membrane pores were finger-like with lower water flux (63.1 ± 12.4 LMH and slightly lower solute rejection (96 ± 2.00% when compared to PSf/PolarClean membranes.

Excited-state inter- and intramolecular proton transfer in methyl 3-hydroxy-2-quinoxalinate: effects of solvent and acid or base concentrations

International Nuclear Information System (INIS)

Dogra, S.K.

2005-01-01

Absorption, fluorescence excitation and fluorescence spectroscopy, combined with time-dependent spectroscopy and semi-empirical (AM1) and density functional theory using Gaussian 98 program calculations have been used to study the effects of solvent and acid or base concentration on the spectral characteristics of methyl 3-hydroxy-2-quinoxalinate (M3HQ). M3HQ is present as enol in less polar solvents and as keto in polar media. In non-polar solvents, large Stokes shifted fluorescence band is assigned to the phototautomer, formed by the excited-state intramolecular proton transfer, whereas fluorescence is only observed from keto in the polar solvents. In aqueous and polar solvents the monocation (MC5/MC6) is formed by protonating the carbonyl oxygen atom in the ground (S 0 ) and the first excited singlet states (S 1 ). Dication is formed by protonating one of ?N- atom of MC5/MC6. Monoanion is formed by deprotonating the phenolic proton of enol in the basic solution. pK a values for different prototropic equilibriums were determined in S 0 and S 1 states and discussed

The bioactive compounds and antioxidant activity of ethanol and ethyl ecetate extracts of Candi Banana (Musa paradisiaca)

Science.gov (United States)

Laeliocattleya, R. A.; Estiasih, T.; Griselda, G.; Muchlisyiyah, J.

2018-03-01

Banana has various benefits for health. One local variety of banana is candi banana (Musa paradisiaca). The aim of this research was to study the content of the bioactive compounds of phenolics, flavonoids, tannin, carotenoids and the antioxidant activity of extract ethanol and ethyl acetate of candi banana. Powdered candi banana was extracted using ethanol and ethyl acetate in an ultrasonic bath. The results showed that the content of phenolics, flavonoids, tannin and carotenoids in ethanol extract were 58.76 ± 3.19 mg/kg, 416.08 ± 18.79 mg/kg, 209.83 ± 15.87 mg/kg and 74.55 ± 4.31 mg/kg, respectively. The content of phenolics, flavonoids, tannin and carotenoids in ethyl acetate extract were 0.83 ± 0.12 mg/kg, 4.31 ± 0.66 mg/kg, 49.97 ± 2.43 mg/kg and 304.40 ± 16.62 mg/kg. While the antioxidant activity (IC50) of ethanol extract and ethyl acetate were 3374.13 ± 123.46 ppm and 40318.19 ± 1014.90 ppm. This research showed that type of solvents of ethanol and ethyl acetate affected the content of bioactive compounds and antioxidant activity of candi banana. The antioxidant activity of ethanol extract was higher than that of ethyl acetate extract. It showed that ethanol was a better solvent than ethyl acetate to extract bioactive compounds in candi banana.

Isolation Of Compounds Of Steroids Teripang Gamat (Stichopus variegatus With Various Types Of Solvents

Directory of Open Access Journals (Sweden)

Meydia Meydia

2016-12-01

Full Text Available Sea cucumber is one of the fisheries commodity that has an important economic value. Generally istraded in dried form (beche-de-mer. One of thebioactive substances contained in sea cucumber is steroidcompounds that serves as an aphrodisiac and sex reversal. The purpose of this study was to extract thesteroid of the gamma sea cucumber by using three types of solvents (methanol, ethyl acetate and hexaneand get the best solvent in producing the highest yield of the steroids. The study revealed that steroid ofgamma sea cucumber (Stichopus variegatus dissolved completely ethyl acetate (semi-polar solvent duringthe first phase, second phase and the third phase of extraction. In the methanol (polar solvent steroids onlydissolved in the first extraction phase, while using the hexane (non polar solvent steroid was undetectable.Fractionation by thin layer chromatography was obtained two fractions that identified as cholesterol (Rf =0.96 and testosterone (Rf = 0.91.

Configuration of a pulse radiolysis system for the study of gas-phase reactions and kinetic investigations of the reactions of hydroxyl radicals with methyl and ethyl radicals

International Nuclear Information System (INIS)

Fagerstroem, K.

1993-01-01

The work that is presented in this thesis deals with the assembling and testing of a pulse radiolysis system for kinetic studies of gas-phase reactions as well as with the kinetics of the gas-phase reactions of hydroxyl radicals with methyl and ethyl radicals. These radicals are very important as these are formed at an early stage in hydrocarbon combustion processes. The two studied reactions are key reactions in those processes. (6 refs., 4 figs., 2 tabs.)

Domain growth of carbon nanotubes assisted by dewetting of thin catalyst precursor films

Energy Technology Data Exchange (ETDEWEB)

Srivastava, Alok Kumar [Defence Materials and Stores R and D Establishment (DRDO), GT Road, Kanpur 208013 (India); Department of Chemical Engineering, Indian Institute of Technology, Kanpur 208016 (India); Sachan, Priyanka; Samanta, Chandan [Department of Chemical Engineering, Indian Institute of Technology, Kanpur 208016 (India); Mukhopadhyay, Kingsuk [Defence Materials and Stores R and D Establishment (DRDO), GT Road, Kanpur 208013 (India); Sharma, Ashutosh, E-mail: ashutos@iitk.ac.in [Department of Chemical Engineering, Indian Institute of Technology, Kanpur 208016 (India)

2014-01-01

We explore self-organized dewetting of ultrathin films of a novel metal complex as a one step surface patterning method to create nanoislands of iron, using which spatially separated carbon nanostructures were synthesized. Dewetting of ultrathin metal complex films was induced by two different methods: liquid solvent exposure and thermal annealing to engender surface patterning. For thermal dewetting, thin films of the iron oleate complex were dewetted at high temperature. In the case of liquid solvent assisted dewetting, the metal complex, mixed with a sacrificial polymer (polystyrene) was spin coated as thin films (<40 nm) and then dewetted under an optimal solution mixture consisting of methyl ethyl ketone, acetone and water. The carrier polymer was then selectively removed to produce the iron metal islands. These metal islands were used for selective growth of discrete patches of multiwall CNTs and CNFs by a chemical vapor deposition (CVD) process. Solvent induced dewetting showed clear advantages over thermal dewetting owing to reduced size of catalyst domains formed by dewetting, an improved control over CNT growth as well as in its ability to immobilize the seed particles. The generic solution mediated dewetting and pattern generation in thin films of various catalytic precursors can thus be a powerful method for selective domain growth of a variety of functional nanomaterials.

Extraction study on uranyl nitrate for energy applications

Science.gov (United States)

Giri, R.; Nath, G.

2017-07-01

Due to the ever-growing demand of energy nuclear reactor materials and the nuclear energy are now considered to be the most critical materials and source of energy for future era. Deposition of nuclear wastes in different industry, nuclear power sector are very much toxic in open environment which are hazardous to living being. There are different methods for extraction and reprocessing of these materials which are cost effective and tedious process. Ultrasonic assisted solvent extraction process is a most efficient and economical way for extraction of such type materials. The presence of third phase in mixing of extractants-diluent pair with aqueous phase imposes the problems in extraction of nuclear reactor materials. The appropriate solvent mixture in proper concentration is an important step in the solvent extraction process. Study of thermo-physical properties helps in selecting an optimum blend for extraction process. In the present work, the extraction of uranium with the binary mixture of Methyl Ethyl Ketone (MEK) and Kerosene was investigated and discussed with the variation of ultrasonic frequency for different temperatures. The result shows that the low frequency and low temperature is suitable environment for extraction. The extraction of uranium by this method is found to be a better result for extraction study in laboratory scale as well as industrial sector.

Free radical detection by means of {sup 2}12Pb mirrors; Deteccion de radicales libres mediante espejos de Pb{sup 2}12

Energy Technology Data Exchange (ETDEWEB)

Molera, M J; Gamboa, J M; Garcia Guijarro, E

1961-07-01

Radicals have been detected at low temperatures (550-700 degree centigrade) in the thermal decomposition of dimethyl and methyl-ethyl-ketone by the Paneth method. the sensitivity of the method has been increased by the use of radioactive mirrors of PB{sup 2}12. They have proved to detect one radical among 2.10{sup 6} molecules. (Author) 18 refs.

Toxicity and carcinogenicity of methyl isobutyl ketone in F344N rats and B6C3F1 mice following 2-year inhalation exposure

International Nuclear Information System (INIS)

Stout, Matthew D.; Herbert, Ronald A.; Kissling, Grace E.; Suarez, Fernando; Roycroft, Joseph H.; Chhabra, Rajendra S.; Bucher, John R.

2008-01-01

Methyl isobutyl ketone (MIBK) is primarily used as a denaturant for rubbing alcohol, as a solvent and in the manufacture of methyl amyl alcohol. Inhalation of vapors is the most likely route of exposure in the work place. In order to evaluate the potential of MIBK to induce toxic and carcinogenic effects following chronic exposure, groups of 50 male and 50 female F344/N rats and B6C3F1 mice were exposed to MIBK at concentrations of 0, 450, 900, or 1800 ppm by inhalation, 6 h/day, 5 days per week for 2 years. Survival was decreased in male rats at 1800 ppm. Body weight gains were decreased in male rats at 900 and 1800 ppm and in female mice at 1800 ppm. The primary targets of MIBK toxicity and carcinogenicity were the kidney in rats and the liver in mice. In male rats, there was increased mineralization of the renal papilla at all exposure concentrations. The incidence of chronic progressive nephropathy (CPN) was increased at 1800 ppm and the severity was increased in all exposed groups. There were also increases in renal tubule hyperplasia at all exposure concentrations, and in adenoma and adenoma or carcinoma (combined) at 1800 ppm; these lesions are thought to represent a continuum in the progression of proliferative lesions in renal tubule epithelium. These increases may have resulted from the increased severity of CPN, either through α2μ-globulin-dependent or -independent mechanisms. An increase in mononuclear cell leukemia at 1800 ppm was an uncertain finding. Adrenal medulla hyperplasia was increased at 1800 ppm, and there was a positive trend for increases in benign or malignant pheochromocytomas (combined). In female rats, there were increases in the incidence of CPN in all exposure concentrations and in the severity at 1800 ppm, indicating that CPN was increased by mechanisms in addition to those related to α2μ-globulin. There were renal mesenchymal tumors, which have not been observed in historical control animals, in two female rats at 1800 ppm. The

Co-solvents transesterification of cotton seed oil into biodiesel: Effects of reaction conditions on quality of fatty acids methyl esters

International Nuclear Information System (INIS)

Alhassan, Y.; Kumar, N.; Bugaje, I.M.; Pali, H.S.; Kathkar, P.

2014-01-01

Highlights: • Using co-solvent systems reduce reaction time by 60%. • Only small volume of co-solvent is required to improve the process. • Greater than 90% yields were obtained within the first 10 min. • Physico-chemical and fuel properties of FAMEs were within standard limits. • Acetone was found to be the best co-solvent for the transesterification. - Abstract: Solvent Technology, is gaining the interest of researchers in improving transesterification process recently. Transesterification of cotton seed oil into biodiesel using different mixtures of methanol with Diethyl Ether (DEE), Dichlorobenzene (CBN) or Acetone (ACT) co-solvent systems was conducted. Potassium hydroxide (KOH) was used as the catalyst all through. The reaction conditions optimized include; the molar ratio of co-solvent in methanol, reaction temperature and time. The catalyst concentration was also optimized. The optimization was based on the percentage yields of Fatty Acids Methyl Esters (FAMEs) produced. In addition, the effects of co-solvent systems on physico-chemical properties (Acid value and fatty acids composition) and fuel properties (viscosity, density and calorific value) were investigated as well. The result obtained, indicated 10% (v/v) addition of co-solvents CBN and ACT in methanol was the optimal volume. The optimal reaction temperature was 55 ° 0 C for 10 min when the catalyst concentration of 0.75% (w/w) weight of oil was used. Fuel properties were within the acceptable limit of ASTM and not significantly affected by the co-solvent systems except for the calorific value. It was concluded that the addition of co-solvent reduced the reaction time and improved some fuel properties of the biodiesel produced

Optimization of Solid Phase Micro-Extraction (SPME for Monitoring Occupational Exposure to Ethyl Benzene

Directory of Open Access Journals (Sweden)

H. Heidari

2009-08-01

Full Text Available AbstractBackground and Objectives: Analytical methods for volatile organic compounds (VOCs in different samples need extraction of compounds, by applying hazardous solvents. Solid phase micro-extraction (SPME is a solvent-free equilibrium extraction method, in which proper calibration can allow quantitative determinations of VOCs at a very good sensitivity without the use of any organic solvent. VOCs are generally present in urine only at trace levels, therefore, a sensitive procedure is needed for their trace determinations. Throughout this study, headspace solid phase micro-extraction (HS-SPME was followed by GC-FID for ethyl benzene in spiked urine was optimized.Methods: In this study, the parameters influencing SPME and gas chromatography of ethyl benzene, including extraction time, temperature, desorption temperature, desorption time, salt addition, sample pH, sample volume and sample agitation were investigated. Results: Extraction procedure was performed at 30°C for 6 min, using 0.2 gml-1 of NaCl in the sample solution. The sample volume and sample pH were optimized at 5 ml and 7 (neutral pH, respectively. Desorption of the ethyl benzene was carried out for 60 sec. at 250°C. The method was also validated with three different spiked urine samples and illustrated an appropriate reproducibility over six consecutive days as well as six within-day experiments. During this investigation, parameters of accuracy, linearity, and detection limits of the procedure were also evaluated.Conclusion: The developed method of HS- SPME-GC-FID proved to be a simple, convenient, and practical procedure, and was successfully used for measuring of ethyl benzene in spiked urine.

Separation of organic azeotropic mixtures by pervaporation. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Baker, R.W.

1991-12-01

Distillation is a commonly used separation technique in the petroleum refining and chemical processing industries. However, there are a number of potential separations involving azetropic and close-boiling organic mixtures that cannot be separated efficiently by distillation. Pervaporation is a membrane-based process that uses selective permeation through membranes to separate liquid mixtures. Because the separation process is not affected by the relative volatility of the mixture components being separated, pervaporation can be used to separate azetropes and close-boiling mixtures. Our results showed that pervaporation membranes can be used to separate azeotropic mixtures efficiently, a result that is not achievable with simple distillation. The membranes were 5--10 times more permeable to one of the components of the mixture, concentrating it in the permeate stream. For example, the membrane was 10 times more permeable to ethanol than methyl ethyl ketone, producing 60% ethanol permeate from an azeotropic mixture of ethanol and methyl ethyl ketone containing 18% ethanol. For the ethyl acetate/water mixture, the membranes showed a very high selectivity to water (> 300) and the permeate was 50--100 times enriched in water relative to the feed. The membranes had permeate fluxes on the order of 0.1--1 kg/m{sup 2}{center_dot}h in the operating range of 55--70{degrees}C. Higher fluxes were obtained by increasing the operating temperature.

Separation of organic azeotropic mixtures by pervaporation

Energy Technology Data Exchange (ETDEWEB)

Baker, R.W.

1991-12-01

Distillation is a commonly used separation technique in the petroleum refining and chemical processing industries. However, there are a number of potential separations involving azetropic and close-boiling organic mixtures that cannot be separated efficiently by distillation. Pervaporation is a membrane-based process that uses selective permeation through membranes to separate liquid mixtures. Because the separation process is not affected by the relative volatility of the mixture components being separated, pervaporation can be used to separate azetropes and close-boiling mixtures. Our results showed that pervaporation membranes can be used to separate azeotropic mixtures efficiently, a result that is not achievable with simple distillation. The membranes were 5--10 times more permeable to one of the components of the mixture, concentrating it in the permeate stream. For example, the membrane was 10 times more permeable to ethanol than methyl ethyl ketone, producing 60% ethanol permeate from an azeotropic mixture of ethanol and methyl ethyl ketone containing 18% ethanol. For the ethyl acetate/water mixture, the membranes showed a very high selectivity to water (> 300) and the permeate was 50--100 times enriched in water relative to the feed. The membranes had permeate fluxes on the order of 0.1--1 kg/m{sup 2}{center dot}h in the operating range of 55--70{degrees}C. Higher fluxes were obtained by increasing the operating temperature.

Convenient synthesis of 6-nor-9,10-dihydrolysergic acid methyl ester.

Science.gov (United States)

Crider, A M; Grubb, R; Bachmann, K A; Rawat, A K

1981-12-01

6-Nor-9,10-dihydrolysergic acid methyl ester (IV) was prepared by demethylation of 9,10-dihydrolysergic acid methyl ester (II) with 2,2,2-trichloroethyl chloroformate, followed by reduction of the intermediate carbamate (III) with zinc in acetic acid. The 6-ethyl-V and 6-n-propyl-VI derivatives were prepared by alkylation of IV with the appropriate halide. All of the ergoline derivatives were evaluated for stereotyped behavior in rats, with 6-nor-6-ethyl-9,10-dihydrolysergic acid methyl ester (V) being active but much less potent than apomorphine. Compound VI was evaluated for its effect on blood pressure; at a dose of 30 mg/kg ip, it significantly lowered, diastolic pressure in normotensive rats.

Isolation Of Compounds Of Steroids Teripang Gamat (Stichopus variegatus With Various Types Of Solvents

Directory of Open Access Journals (Sweden)

Meydia Meydia

2017-02-01

Full Text Available AbstractSea cucumber is one of the fisheries commodity that has an important economic value. Generally is traded in dried form (beche-de-mer. One of thebioactive substances contained in sea cucumber is steroid compounds that serves as an aphrodisiac and sex reversal. The purpose of this study was to extract the steroid of the gamma sea cucumber by using three types of solvents (methanol, ethyl acetate and hexane and get the best solvent in producing the highest yield of the steroids. The study revealed that steroid of gamma sea cucumber (Stichopus variegatus dissolved completely ethyl acetate (semi-polar solvent during the first phase, second phase and the third phase of extraction. In the methanol (polar solvent steroids only dissolved in the first extraction phase, while using the hexane (non polar solvent steroid was undetectable. Fractionation by thin layer chromatography was obtained two fractions that identified as cholesterol (Rf = 0.96 and testosterone (Rf = 0.91.

Purification and characterization of a novel recombinant highly enantioselective short-chain NAD(H)-dependent alcohol dehydrogenase from Thermus thermophilus.

Science.gov (United States)

Pennacchio, Angela; Pucci, Biagio; Secundo, Francesco; La Cara, Francesco; Rossi, Mosè; Raia, Carlo A

2008-07-01

The gene encoding a novel alcohol dehydrogenase (ADH) that belongs to the short-chain dehydrogenase/reductase (SDR) superfamily was identified in the extremely thermophilic, halotolerant gram-negative eubacterium Thermus thermophilus HB27. The T. thermophilus ADH gene (adh(Tt)) was heterologously overexpressed in Escherichia coli, and the protein (ADH(Tt)) was purified to homogeneity and characterized. ADH(Tt) is a tetrameric enzyme consisting of identical 26,961-Da subunits composed of 256 amino acids. The enzyme has remarkable thermophilicity and thermal stability, displaying activity at temperatures up to approximately 73 degrees C and a 30-min half-inactivation temperature of approximately 90 degrees C, as well as good tolerance to common organic solvents. ADH(Tt) has a strict requirement for NAD(H) as the coenzyme, a preference for reduction of aromatic ketones and alpha-keto esters, and poor activity on aromatic alcohols and aldehydes. This thermophilic enzyme catalyzes the following reactions with Prelog specificity: the reduction of acetophenone, 2,2,2-trifluoroacetophenone, alpha-tetralone, and alpha-methyl and alpha-ethyl benzoylformates to (S)-(-)-1-phenylethanol (>99% enantiomeric excess [ee]), (R)-alpha-(trifluoromethyl)benzyl alcohol (93% ee), (S)-alpha-tetralol (>99% ee), methyl (R)-(-)-mandelate (92% ee), and ethyl (R)-(-)-mandelate (95% ee), respectively, by way of an efficient in situ NADH-recycling system involving 2-propanol and a second thermophilic ADH. This study further supports the critical role of the D37 residue in discriminating NAD(H) from NADP(H) in members of the SDR superfamily.

Solvents interactions with thermochromic print

Directory of Open Access Journals (Sweden)

Mirela Rožić

2017-12-01

Full Text Available In this study, the interactions between different solvents (benzene, acetone, cyclohexanone, various alcohols and water and thermochromic printing ink were investigated. Thermochromic printing ink was printed on metal surface. Components of thermochromic printing inks are polymeric microcapsules and classic yellow offset printing ink. Below its activation temperature, dye and developer within the microcapsules form a blue coloured complex. Therefore, thermochromic print is green. By heating above the activation temperature, blue colour of the complex turns into the leuco dye colourless state and the green colour of the prints turns into the yellow colour of the classic offset pigment. The results of the interaction with various solvents show that the thermochromic print is stable in all tested solvents except in ethanol, acetone and cyclohexanone. In ethanol, the green colour of the print becomes yellow. SEM analysis shows that microcapsules are dissolved. In acetone and cyclohexanone, the green colour of the print turns into blue, and the microcapsules become significantly more visible. Thus, the yellow pigment interacts with examined ketones. Based on the obtained interactions it can be concluded that the microcapsules have more polar nature than the classical pigment particles. Solvent-thermocromic print interactions were analysed using Hansen solubility parameters that rank the solvents based on their estimated interaction capabilities.

Accuracy Profiles for Analyzing Residual Solvents in Textiles by GC-MS.

Science.gov (United States)

Bao, Qibei; Fu, Kejie; Ren, Qingqing; Zhong, Yingying; Qian, Dan

2017-10-01

Excess residual solvents (RSs) in clothes or other textiles could be toxic and pose risks to both humans and the environment. N,N-Dimethylformamide (DMF), N,N-dimethylacetamide (DMAc) and 1-methyl-2-pyrrolidinone (NMP) are important chemicals frequently used as solvents in the textile industry. Several organizations have proposed limiting DMF, DMAc and NMP in textiles, but an appropriate detection method has not been proposed. A sensitive GC-MS method for the quantification of DMF, DMAc and NMP in textiles was developed. After extraction with ethyl acetate, these RSs were separated on a DB-5MS capillary column. The oven temperature was increased from 50°C (held for 0.5 min) at 10°C/min to 120°C (held for 1 min). The method was fully validated according to the accuracy profile procedure, which is based on β-expectation tolerance intervals for the total measurement bias. Linearity was observed in the range of 0.5-10 mg/L for the solvents with limit of quantification values of 4.2, 3.5 and 2.5 mg/kg for DMF, DMAc and NMP, respectively. The repeatability and intermediate precision were NMP. The recoveries of DMF, DMAc and NMP were 91.2-106.3%, 89.5-97.7% and 85.6-101.3%, respectively. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Reactions of ethyl diazoacetate catalyzed by methylrhenium trioxide

Energy Technology Data Exchange (ETDEWEB)

Zhu, Z.; Espenson, H. [Iowa State Univ., Ames, IA (United States)

1995-11-03

Methylrhenium trioxide (CH{sub 3}ReO{sub 3} or MTO) has found wise use in catalysis, including the epoxidation and metathesis of olefins, aldehyde olefination, and oxygen transfer. Extensive reports have now appeared in the area of MTO-catalyzed substrate oxidations with hydrogen peroxide. Certain catalytic applications of MTO for organic reactions that do not utilize peroxide have now been realized. In particular, a catalytic amount of MTO with ethyl diazoacetate (EDA) will convert aromatic imines to aziridines and convert aldehydes and ketones to epoxides. The aziridine preparation proceeds in high yields under anaerobic conditions more conveniently than with existing methods. Compounds with a three-membered heterocyclic ring can be obtained with the EDA/MTO catalytic system. Aromatic imines undergo cycloaddition reactions to give aziridines under mild conditions.

Informal Conference on Photochemistry Held in Atlanta, Georgia on 26 April-1 May, 1992

Science.gov (United States)

1992-05-01

of the kinetics of such reactions. We have measured rate constants for the neopentyl peroxy radical, generating the alkyl radical by laser flash... glycol diacetate) > Ketones(acetone.acetophenone) > Ethers(tetrahydrofuran. dioxane). Nltrlles(acetonltrlle).Halogenated hydrocarbons (carbon...the best solvent to synthesis of CBDA. especially ethyl acetate (Y63% /KW Hr) and ethylene glycol diacetate (Y55,/lW Hr).i (2) TEMPERATURE CBDA yield

[Study on chemical constituents from ethyl acetate extract of Myricaria bracteata].

Science.gov (United States)

Zhang, Ying; Yuan, Yi; Cui, Baosong; Li, Shuai

2011-04-01

To study the chemical constituents from the ethyl acetate extract of Myricaria bracteata. The chemical constituents were isolated and purified by chromatographic techniques, and their structures were identified by physical characters and spectroscopic analysis. Sixteen compounds were isolated from the ethyl acetate portion of the 95% ethanolic extract of Myricaria bracteata, and identified as myricarin (1), myricarin B (2), 3alpha-hydroxytaraxer-14-en-28-oic acid (3), myricadiol (4), trans-ferulic acid 22-hydroxydocosanoic acid ester (5), docosyl-3, 4-dihydroxy-trans-cinnamate (6), dillenetin (7), 3, 5, 4'-trihydroxy-7-methoxyflavone (8), 3, 5, 4'-trihydroxy-7, 3'-dimethoxyflavone (9), methyl 3, 5-dihydroxy-4-methoxybenzoate (10), 3-hydroxy-4-methoxy cinnamic acid (11), sinapaldehyde (12), vanillin (13), syringaldehyde (14), 3, 3', 4'-trimethoxyellagic acid (15), methyl p-hyroxybenzoate (16). Compounds 5, 6, 12-16 were isolated from the genus Myricaria for the fist time, all of the compounds were isolated from this plant for the fist time, except for 8 and 9.

Synergic extraction of europium (III) by TTA and selected carbinols or ketons in carbontetrachloride

International Nuclear Information System (INIS)

El-Naggar, H.A.; El-Madany, S.

1988-01-01

The extraction of Eu(III) by HTTA dissolved in CCl 4 has been carried from acid-perchlorate and acid-acetate solutions. Some oxygen containing solvents have been added to the chelate in extraction of the acetate complex of Eu(III). The reaction mechanisms and the equilibrium constants are calculated for the different extracted species. The data obtained are discussed in the light of the structure of carbinols and ketones used as adducts

Characterization of volatile aroma compounds in different brewing barley cultivars.

Science.gov (United States)

Dong, Liang; Hou, Yingmin; Li, Feng; Piao, Yongzhe; Zhang, Xiao; Zhang, Xiaoyu; Li, Cheng; Zhao, Changxin

2015-03-30

Beer is a popular alcoholic malt beverage resulting from fermentation of the aqueous extract of malted barley with hops. The aroma of brewing barley impacts the flavor of beer indirectly, because some flavor compounds or their precursors in beer come from the barley. The objectives of this research were to study volatile profiles and to characterize odor-active compounds of brewing barley in order to determine the variability of the aroma composition among different brewing barley cultivars. Forty-one volatiles comprising aldehydes, ketones, alcohols, organic acids, aromatic compounds and furans were identified using solid phase microextraction combined with gas chromatography/mass spectrometry, among which aldehydes, alcohols and ketones were quantitatively in greatest abundance. Quantitative measurements performed by means of solvent extraction and calculation of odor activity values revealed that acetaldehyde, 2-methylpropanal, 3-methylbutanal, 2-methylbutanal, hexanal, heptanal, octanal, nonanal, 3-methyl-1-butanol, cyclopentanol, 2,3-butanedione, 2,3-pentanedione, 2-heptanone, acetic acid, ethyl acetate, 2-pentylfuran and benzeneacetaldehyde, whose concentrations exceeded their odor thresholds, could be considered as odor-active compounds of brewing barley. Principal component analysis was employed to evaluate the differences among cultivars. The results demonstrated that the volatile profile based on the concentrations of aroma compounds enabled good differentiation of most barley cultivars. © 2014 Society of Chemical Industry.

Colorimetric determination of uranium using ammonium thiocyanate in a medium of ethyl acetate, acetone and water; Dosage colorimetrique de l'uranium par le thiocyanate d'ammonium en milieu acetate d'ethyle-acetone-eau

Energy Technology Data Exchange (ETDEWEB)

Hucleux, M; Dessapt, P

1959-04-01

The method consists of colorimetrically analyzing uranium using ammonium sulfo-cyanide in the solvent phase. The optimum conditions for extracting uranium by ethyl acetate have been studied. A precise colorimetric method was established which depends on the extracted phase and on the behavior of the ethyl acetate-acetone medium. (author) [French] La methode consiste a doser l'uranium par colorimetrie au sulfocyanure d'ammonium en phase solvant. Les meilleures conditions d'extraction de l'uranium par l'acetate d'ethyle ont ete etudiees. Une colorimetrie precise a ete mise au point en fonction de l'acidite de la phase extraite et du comportement du milieu acetate d'ethyleacetone. (auteur)

The use of organic solvents in mutagenicity testing.

Science.gov (United States)

Abbondandolo, A; Bonatti, S; Corsi, C; Corti, G; Fiorio, R; Leporini, C; Mazzaccaro, A; Nieri, R; Barale, R; Loprieno, N

1980-10-01

13 organic substances (dimethylsulfoxide, methanol, ethanol, n-propyl alcohol, sec-butyl alcohol, tert-butyl alcohol, dl-sec-amyl alcohol, ethylene glycol, ethylene glycol monomethyl ether, 1,4-diethylene dioxide, acetone, methyl acetate and formamide) were considered from the standpoint of their use as solvents for water-insoluble chemicals to be tested for mutagenicity. First, the effect of these solvents on cell survival was studied in the yeast Schizosaccharomyces pombe and in V79 Chinese hamster cells. 8 solvents showing relatively low toxicity on either cell system (dimethylsulfoxide, ethanol, ethylene glycol, ethylene glycol monomethyl ether, 1,4-diethylene dioxide, acetone, methyl acetate and formamide) were tested for their effect on aminopyrine demethylase. 4 solvents (ethanol, 1,4-diethylene dioxide, methyl acetate and formamide) showed a more or less pronounced adverse effect on the microsomal enzymic activity. The remaining 4 and methanol (whose effect on aminopyrine demethylase was not testable) were assayed for mutagenicity in S. pombe. They all gave negative results both with and without the post-mitochondrial fraction from mouse liver.

Measurement and prediction of aromatic solute distribution coefficients for aqueous-organic solvent systems. Final report

Energy Technology Data Exchange (ETDEWEB)

Campbell, J.R.; Luthy, R.G.

1984-06-01

Experimental and modeling activities were performed to assess techniques for measurement and prediction of distribution coefficients for aromatic solutes between water and immiscible organic solvents. Experiments were performed to measure distribution coefficients in both clean water and wastewater systems, and to assess treatment of a wastewater by solvent extraction. The theoretical portions of this investigation were directed towards development of techniques for prediction of solute-solvent/water distribution coefficients. Experiments were performed to assess treatment of a phenolic-laden coal conversion wastewater by solvent extraction. The results showed that solvent extraction for recovery of phenolic material offered several wastewater processing advantages. Distribution coefficients were measured in clean water and wastewater systems for aromatic solutes of varying functionality with different solvent types. It was found that distribution coefficients for these compounds in clean water systems were not statistically different from distribution coefficients determined in a complex coal conversion process wastewater. These and other aromatic solute distribution coefficient data were employed for evaluation of modeling techniques for prediction of solute-solvent/water distribution coefficients. Eight solvents were selected in order to represent various chemical classes: toluene and benzene (aromatics), hexane and heptane (alkanes), n-octanol (alcohols), n-butyl acetate (esters), diisopropyl ether (ethers), and methylisobutyl ketone (ketones). The aromatic solutes included: nonpolar compounds such as benzene, toluene and naphthalene, phenolic compounds such as phenol, cresol and catechol, nitrogenous aromatics such as aniline, pyridine and aminonaphthalene, and other aromatic solutes such as naphthol, quinolinol and halogenated compounds. 100 references, 20 figures, 34 tables.

Influence of alkyl chain length and temperature on thermophysical properties of ammonium-based ionic liquids with molecular solvent.

Science.gov (United States)

Kavitha, T; Attri, Pankaj; Venkatesu, Pannuru; Devi, R S Rama; Hofman, T

2012-04-19

Mixing of ionic liquids (ILs) with molecular solvent can expand the range of structural properties and the scope of molecular interactions between the molecules of the solvents. Exploiting of these phenomena essentially require a basic fundamental understanding of mixing behavior of ILs with molecular solvents. In this context, a series of protic ILs possessing tetra-alkyl ammonium cation [R(4)N](+) with commonly used anion hydroxide [OH](-) were synthesized and characterized by temperature dependent thermophysical properties. The ILs [R(4)N](+)[OH](-) are varying only in the length of alkyl chain (R is methyl, ethyl, propyl, or butyl) of tetra-alkyl ammonium on the cationic part. The ILs used for the present study included tetramethyl ammonium hydroxide [(CH(3))(4)N](+)[OH](-) (TMAH), tetraethyl ammonium hydroxide [(C(2)H(5))(4)N](+)[OH](-) (TEAH), tetrapropyl ammonium hydroxide [(C(3)H(7))(4)N](+)[OH](-) (TPAH) and tetrabutyl ammonium hydroxide [(C(4)H(9))(4)N](+)[OH](-) (TBAH). The alkyl chain length effect has been analyzed by precise measurements such as densities (ρ), ultrasonic sound velocity (u), and viscosity (η) of these ILs with polar solvent, N-methyl-2-pyrrolidone (NMP), over the full composition range as a function of temperature. The excess molar volume (V(E)), the deviation in isentropic compressibility (Δκ(s)) and deviation in viscosity (Δη) were predicted using these properties as a function of the concentration of ILs. Redlich-Kister polynomial was used to correlate the results. A qualitative analysis of the results is discussed in terms of the ion-dipole, ion-pair interactions, and hydrogen bonding between ILs and NMP molecules. Later, the hydrogen bonding features between ILs and NMP were also analyzed using a molecular modeling program with the help of HyperChem 7.

Separation of sup(99m)Tc from 99MoO3

International Nuclear Information System (INIS)

Tomicic, M.

1977-07-01

At the present time sup(99m)Tc is widely used in nuclear medicine and its uses are increasing. It can be produced by various methods, and of those most frequently used today two have special features making them particularly applicable to the large-scale production of instant sup(99m)Tc - these are solvent extraction with methyl-ethyl-ketone and the sublimation methods. This report presents a bibliographic review of these methods, their main perfomance parameters, and experience obtained from the development and operation of a sublimation generator. Separation of sup(99m)Tc from irradiated MoO 3 was carried out with high yields (75-95%) after multiple repetition of the separation process with molybdenum trioxide heated for half an hour at a maximum temperature of 850-890 deg C in an air flow. The activity ratio of molybdenum in the separated sup(99m)Tc was of the order of 4 x 10 -5 . (author)

Concentration determination of methyl magnesium chloride and other Grignard reagents by potentiometric titration with in-line characterization of reaction species by FTIR spectroscopy.

Science.gov (United States)

Chen, Yadan; Wang, Tao; Helmy, Roy; Zhou, George X; LoBrutto, Rosario

2002-07-01

A potentiometric titration method for methyl magnesium chloride and other Grignard reagents based on the reaction with 2-butanol in THF has been developed and validated. The method employs a commercially available platinum electrode, using an electrolyte compatible with non-aqueous solvents. Well-defined titration curves were obtained, along with excellent method precision. The endpoint was precisely determined based on the first derivative of the titration curve. Different solvents such as THF, diethyl ether and methylene chloride provided similar results with regard to sharpness of the endpoint and method precision. The method was applied to a wide array of Grignard reagents including methyl magnesium bromide, ethyl magnesium chloride, propyl magnesium chloride, vinyl magnesium chloride, phenyl magnesium chloride, and benzyl magnesium chloride with similar precision and accuracy. Application of in-line FTIR was demonstrated for in situ monitoring of the titration reaction, allowing characterization of the reaction species. An authentic spectrum of the MeMgCl-THF complex was obtained using spectral subtraction and the vibrational absorbance bands were identified. FTIR also provided an alternative for detecting the titration endpoint, and the titration results so obtained, provided a cross-validation of the accuracy of the potentiometric titration.

[COMPARATIVE SENSITIVITY OF CHOLINESTERASES IN VERTEBRATES AND INVERTEBRATES TO HIGHLY SPECIFIC ORGANOPHOSPHORUS INHIBITORS DIISOPROPYL FLUOROPHOSPHATE (DFP) AND (2-ETHOXYMETHYL PHOSPHORYL THIOETHYL) ETHYL (METHYL) SULPHONIUM SULPHOMETHYLAT (GD-42)].

Science.gov (United States)

Basova, N E; Kormilitsyn, B N; Perchenok, A Yu; Rozengart, E V; Saakov, V S; Suvorov, A A

2015-01-01

The review presents data on comparative reactivity of 68 cholinesterase preparation from various organs and tissues in a number of vertebrates and invertebrates based on sensitivity to two highly specific and most studied organophosphorus inhibitors--diisopropyl fluorophosphates (DFP) and (2-ethoxymethyl phosphoryl thioethyl) ethyl (methyl) sulphonium sulphomethylat (GD-42). Analysis of these data suggests a great diversity in enzymologic characteristics of cholinesterase preparation in representatives of vertebrates and invertebrates, this variety observed even for closely related enzymes in animals of almost the same level of development.

SnCl2/TiCl3-Mediated Deoximation of Oximes in an Aqueous Solvent

Directory of Open Access Journals (Sweden)

Tsung-Hsun Chuang

2012-03-01

Full Text Available A simple procedure for SnCl2/TiCl3-mediated deoximation of ketoximes in an aqueous solvent is reported. Under the conditions developed in this effort, various ketones and aldehydes are produced in good to excellent yields.

Prototropic tautomerism of 4-Methyl 1,2,4-Triazole-3-Thione molecule in solvent water medium: DFT and Car–Parrinello molecular dynamics study

International Nuclear Information System (INIS)

Dutta, Bipan; De, Rina; Chowdhury, Joydeep

2015-01-01

Highlights: • The tautomerism of 4-MTTN molecule in solvent water medium has been investigated. • CPMD presage the possibility of PT reactions through the solvent water medium. • Concerted PT processes in 4-MTTN have been estimated from the DFT and NBO analyses. • Percentage evolution and breaking of the concerned bonds are estimated. - Abstract: The ground state prototropic tautomerism of 4-Methyl 1,2,4-Triazole-3-Thione molecule in solvent water medium has been investigated with the aid of DFT and Car–Parrinello molecular dynamics (CPMD) simulation studies. The CPMD simulations envisage the possibility of proton transfer reactions of the molecule through the solvent water medium. Probable proton transfer pathways have been predicted from the DFT calculations which are substantiated by the natural bond orbital analyses. The evolution and breaking of the concerned bonds of the molecule for different proton transfer reaction pathways are also estimated.

Optimization of Solid Phase Micro-Extraction (SPME for Monitoring Occupational Exposure to Ethyl Benzene

Directory of Open Access Journals (Sweden)

H Heidari

2012-05-01

Full Text Available

Background and Objectives: Analytical methods for volatile organic compounds (VOCs in different samples need extraction of compounds, by applying hazardous solvents. Solid phase micro-extraction (SPME is a solvent-free equilibrium extraction method, in which proper calibration can allow quantitative determinations of VOCs at a very good sensitivity without the use of any organic solvent. VOCs are generally present in urine only at trace levels, therefore, a sensitive procedure is needed for their trace determinations. Throughout this study, headspace solid phase micro-extraction (HS-SPME was followed by GC-FID for ethyl benzene in spiked urine was optimized.

Methods: In this study, the parameters influencing SPME and gas chromatography of ethyl benzene, including extraction time, temperature, desorption temperature, desorption time, salt addition, sample pH, sample volume and sample agitation were investigated.

Results: Extraction procedure was performed at 30^°C for 6 min, using 0.2 gml^-1 of NaCl in the sample solution. The sample volume and sample pH were optimized at 5 ml and 7 (neutral pH, respectively. Desorption of the ethyl benzene was carried out for 60 sec. at 250^°C. The method was also validated with three different spiked urine samples and illustrated an appropriate reproducibility over six consecutive days as well as six within-day experiments. During this investigation, parameters of accuracy, linearity, and detection limits of the procedure were also evaluated.

Conclusion: The developed method of HS- SPME-GC-FID proved to be a simple, convenient, and practical procedure, and was successfully used for measuring of ethyl benzene in spiked urine.

Substitution of carcinogenic solvent dichloromethane for the extraction of volatile compounds in a fat-free model food system.

Science.gov (United States)

Cayot, Nathalie; Lafarge, Céline; Bou-Maroun, Elias; Cayot, Philippe

2016-07-22

Dichloromethane is known as a very efficient solvent, but, as other halogenated solvents, is recognized as a hazardous product (CMR substance). The objective of the present work is to propose substitution solvent for the extraction of volatile compounds. The most important physico-chemical parameters in the choice of an appropriate extraction solvent of volatile compounds are reviewed. Various solvents are selected on this basis and on their hazard characteristics. The selected solvents, safer than dichloromethane, are compared using the extraction efficiency of volatile compounds from a model food product able to interact with volatile compounds. Volatile compounds with different hydrophobicity are used. High extraction yields were positively correlated with high boiling points and high Log Kow values of volatile compounds. Mixtures of solvents such as azeotrope propan-2-one/cyclopentane, azeotrope ethyl acetate/ethanol, and mixture ethyl acetate/ethanol (3:1, v/v) gave higher extraction yields than those obtained with dichloromethane. Copyright © 2016 Elsevier B.V. All rights reserved.

Synthesis and Antimicrobial Activity of Novel 3-[1-(3-nitrophenyl)-ethyl

African Journals Online (AJOL)

Syntheses of novel 3-[1-(3-nitrophenyl)-ethyl]-1-(indole-1-yl) substituted aryl/alkyl phosphinoyl/thiophosphinoyl/selenophosphinoyl-1H-indole derivatives were accomplished in two steps. The synthetic route involves the cyclisation of equimolar quantities of 3-[1H-3-indolyl(3-nitrophenyl)methyl]-1H-indole with dichlorophenyl ...

Reaction rate constants of H-abstraction by OH from large ketones: Measurements and site-specific rate rules

KAUST Repository

Badra, Jihad

2014-01-01

Reaction rate constants of the reaction of four large ketones with hydroxyl (OH) are investigated behind reflected shock waves using OH laser absorption. The studied ketones are isomers of hexanone and include 2-hexanone, 3-hexanone, 3-methyl-2-pentanone, and 4-methl-2-pentanone. Rate constants are measured under pseudo-first-order kinetics at temperatures ranging from 866 K to 1375 K and pressures near 1.5 atm. The reported high-temperature rate constant measurements are the first direct measurements for these ketones under combustion-relevant conditions. The effects of the position of the carbonyl group (CO) and methyl (CH3) branching on the overall rate constant with OH are examined. Using previously published data, rate constant expressions covering, low-to-high temperatures, are developed for acetone, 2-butanone, 3-pentanone, and the hexanone isomers studied here. These Arrhenius expressions are used to devise rate rules for H-abstraction from various sites. Specifically, the current scheme is applied with good success to H-abstraction by OH from a series of n-ketones. Finally, general expressions for primary and secondary site-specific H-abstraction by OH from ketones are proposed as follows (the subscript numbers indicate the number of carbon atoms bonded to the next-nearest-neighbor carbon atom, the subscript CO indicates that the abstraction is from a site next to the carbonyl group (CO), and the prime is used to differentiate different neighboring environments of a methylene group):P1,CO = 7.38 × 10-14 exp(-274 K/T) + 9.17 × 10-12 exp(-2499 K/T) (285-1355 K)S10,CO = 1.20 × 10-11 exp(-2046 K/T) + 2.20 × 10-13 exp(160 K/T) (222-1464 K)S11,CO = 4.50 × 10-11 exp(-3000 K/T) + 8.50 × 10-15 exp(1440 K/T) (248-1302 K)S11′,CO = 3.80 × 10-11 exp(-2500 K/T) + 8.50 × 10-15 exp(1550 K/T) (263-1370 K)S 21,CO = 5.00 × 10-11 exp(-2500 K/T) + 4.00 × 10-13 exp(775 K/T) (297-1376 K) © 2014 the Partner Organisations.

Combustion by synthesis in pilot scale of nanocatalyst Ni_0_,_5Zn_0_,_5Fe_2O_4 and the performance in methyl and ethyl esterification to obtaining biodiesel

International Nuclear Information System (INIS)

Moura, T.F.B.; Barros, A.B.S.; Dantas, J.; Pereira, K.R.O.; Vasconcelos, E.V.; Costa, A.C.F.M.

2016-01-01

To produce biodiesel from the use of catalysts is necessary because help in getting better reaction yields and currently magnetic materials has gained prominence for this application. This study aimed to prepare the nanocatalyst Ni_0_,_5Zn_0_,_5Fe_2O_4 in laboratory scale, to evaluate their performance in methyl AND ethyl esterification using acidified soybean oil as raw material. The samples were synthesized by reaction in a combustion reactor with a production capacity of 200g / batch and characterized by XRD, TG and EDX. The catalytic tests took place at a temperature of 180 ° C / 1h, molar ratio 1:12, 2% nanocatalyst and analyzed by gas chromatography. Samples showed the major phase of the inverse spinel with an average crystallite size of 20.25 nm and traces of segregated phases of Fe_2O_3 and ZnO. The values of the detected oxides were 68.01% for Fe2O3, 16.57% for NiO and 15.28% for ZnO, values that are close to the calculated theoretical. The sample showed total mass loss equal to 6.5%, demonstrating its excellent thermal stability. The biodiesel conversion results were 84.11 and 73.74% for methyl ethyl route, respectively. Therefore, the synthesized material has catalytic potential in the tested reaction and could be a promising material for both assessed routes. (author)

Continuous-flow Heck synthesis of 4-methoxybiphenyl and methyl 4-methoxycinnamate in supercritical carbon dioxide expanded solvent solutions

Directory of Open Access Journals (Sweden)

Phei Li Lau

2013-12-01

Full Text Available The palladium metal catalysed Heck reaction of 4-iodoanisole with styrene or methyl acrylate has been studied in a continuous plug flow reactor (PFR using supercritical carbon dioxide (scCO2 as the solvent, with THF and methanol as modifiers. The catalyst was 2% palladium on silica and the base was diisopropylethylamine due to its solubility in the reaction solvent. No phosphine co-catalysts were used so the work-up procedure was simplified and the green credentials of the reaction were enhanced. The reactions were studied as a function of temperature, pressure and flow rate and in the case of the reaction with styrene compared against a standard, stirred autoclave reaction. Conversion was determined and, in the case of the reaction with styrene, the isomeric product distribution was monitored by GC. In the case of the reaction with methyl acrylate the reactor was scaled from a 1.0 mm to 3.9 mm internal diameter and the conversion and turnover frequency determined. The results show that the Heck reaction can be effectively performed in scCO2 under continuous flow conditions with a palladium metal, phosphine-free catalyst, but care must be taken when selecting the reaction temperature in order to ensure the appropriate isomer distribution is achieved. Higher reaction temperatures were found to enhance formation of the branched terminal alkene isomer as opposed to the linear trans-isomer.

Flotation of uranium values using di (2-ethyl hexyl) phosphoric acid

International Nuclear Information System (INIS)

Singh, Ajoy Kumar; Padmanabhan, N.P.H.; Sridhar, U.; Krishna Rao, N.

1998-01-01

The use of solvent extractants for mineral flotation, especially for difficult-to-float minerals, is gaining importance as they are highly selective to specific metal ions and form strong and stable complexes mostly by chelation. Studies carried out with di(2 ethyl hexyl) phosphoric acid (D2EHPA) (an organic solvent used in the extraction of uranium from phosphoric acid) as collector for flotation of uranium minerals from ore samples of Domiasiat, Meghalaya and Jaduguda, Bihar have yielded encouraging results. Although flotation of uranium minerals using other solvent extractants like tributyl phosphoric acid (TBP) has been studied, the uraninite-D2EHPA system has not been tested so far. This technical note puts on record the findings of the preliminary studies carried out. (author)

Viscosity of binary mixtures of 1-ethyl-3-methylimidazolium tetrafluoroborate ionic liquid with four organic solvents

International Nuclear Information System (INIS)

Ciocirlan, Oana; Croitoru, Oana; Iulian, Olga

2016-01-01

Highlights: • Viscosities of four binary mixtures of [Emim][BF4] with organic solvents. • Viscosity models based on Eyring’s theory. • Excess functions calculated. • Data for binaries new in the literature, except for system with DMSO. - Abstract: This paper reports experimental values of dynamic viscosity for four binary systems of 1-ethyl-3-methylimidazolium tetrafluoroborate, [Emim][BF4], with dimethyl sulfoxide (DMSO), acetonitrile (ACN), ethylene glycol (EG) and 1,4-dioxane over the temperature ranges from 293.15 K to 353.15 K at p = 0.1 MPa. All binary mixtures were completely miscible over the entire range of mole fraction, except the system with 1,4-dioxane. The viscosity results have been correlated by the one parameter Grunberg–Nissan and Fang and He equations and the two-parameter McAllister, Eyring-UNIQUAC, Eyring-NRTL and Eyring-Wilson models and the results were compared. Additionally, the viscosity deviations, Δη, and the excess Gibbs energy of activation for viscous flow, G"∗"E, were calculated and fitted to the Redlich–Kister equation. The results show that all Δη values are negative over the whole composition range and the G"∗"E values are positive, except for the system with EG. The results of the excess functions are discussed in terms of molecular interactions.

Synthesis and in vivo evaluation of [O-methyl-11C](2R,4R)-4-hydroxy-2-[2-[2-[2-(3-methoxy)phenyl]ethyl]phenoxy] ethyl-1-methylpyrrolidine as a 5-HT2A receptor PET ligand

International Nuclear Information System (INIS)

Kumar, J.S. Dileep; Prabhakaran, Jaya; Erlandsson, Kjell; Majo, Vattoly J.; Simpson, Norman R.; Pratap, Mali; Heertum, Ronald L. van; Mann, J. John; Parsey, Ramin V.

2006-01-01

The serotonin 2A (5-HT 2A ) receptor is implicated in the pathophysiology of schizophrenia and mood disorders, and in vivo studies of this receptor would be of value in studying the pathophysiology of these disorders and in measuring the relationship of clinical response to receptor occupancy for 5-HT 2A antagonists such as atypical antipsychotics. Therefore, (2R,4R)-4-hydroxy-2-[2-[2-[2-(3-methoxy)-phenyl]ethyl] phenoxy]ethyl-1-methylpyrrolidine (MPM) (13), a selective and high-affinity (K i =0.79 nM) 5HT 2A antagonist, has been radiolabeled with carbon-11 by O-methylation of the corresponding desmethyl analogue (2R,4R)-4-hydroxy-2-[2-[2-[2-(3-hydroxy)phenyl]ethyl]phenoxy] ethyl-1-methylpyrrolidine (12) with [ 11 C]methyltriflate in order to determine the suitability of [ 11 C]MPM to quantify 5-HT 2A in living brain using PET. Desmethyl-MPM 12 and standard MPM were prepared, starting from 3-hydroxymethylphenol (2), in excellent yield. The yield obtained for radiolabeling was 40±5% (EOB), and the total synthesis time was 30 min at EOS. PET studies with [ 11 C]MPM in baboon showed a distribution in the brain consistent with the known distribution of 5-HT 2A receptors. The time-activity curves for the high-binding regions peaked at ∼45 min after injection. Blocking studies with M100907 demonstrated not only 38-57% blocking of tracer binding in brain regions known to have 5-HT 2A receptors but also 38% blocking in cerebellum, which has a low 5-HT 2A receptor concentration. Although [ 11 C]MPM exhibits appropriate kinetics in baboon for imaging 5-HT 2A receptors, its specific binding in cerebellum and higher proportion of nonspecific binding limit its usefulness for the in vivo quantification of 5-HT 2A receptors with PET

Crystal structure of the tetragonal polymorph of bis(1-ethyl-3-methylimidazolium tetrabromidocadmate

Directory of Open Access Journals (Sweden)

Tamara Đorđević

2016-07-01

Full Text Available Both unique Cd atoms in the tetragonal polymorph of bis(1-ethyl-3-methylimidazolium tetrabromidocadmate, (C6H11N22[CdBr4], occupy special positions (site symmetry -4. The crystal structure consists of isolated tetrahedral [CdBr4]2− anions which are surrounded by 1-ethyl-3-methylimidazolium cations. The methyl and ethyl side chains of the cations show positional disorder in a 0.590 (11:0.410 (11 ratio. In the crystal, (C6H11N2+ cations display three weak C—H...Br hydrogen-bond interactions through the imidazolium ring H atoms with the Br− ligands of the surrounding complex anions. The alkyl groups of the side chains are not involved in hydrogen bonding.

Impact of coexposure on toluene biomarkers in rats.

Science.gov (United States)

Cosnier, Frédéric; Nunge, Hervé; Brochard, Céline; Burgart, Manuella; Rémy, Aurélie; Décret, Marie-Josèphe; Cossec, Benoît; Campo, Pierre

2014-03-01

1. Toluene (TOL) is widely used in industry. Occupational exposure to TOL is commonly assessed using TOL in blood, hippuric acid and ortho-cresol. Levels of these biomarkers may depend on factors potentially interfering with TOL biotransformation, such as the presence of other solvents in the workplace. Mercapturic acids (MAs) could be an alternative to the "traditional" TOL biomarkers. 2. This study aims (1) to investigate in rat the effects of an exposure to vapours mixtures on the TOL metabolism, and (2) to assess how well MAs performed in these contexts compared to the traditional TOL biomarkers. 3. Rats were exposed by inhalation to binary mixtures of TOL with n-butanol (BuOH), ethyl acetate (EtAc), methyl ethyl ketone (MEK) or xylenes (XYLs); biological exposure indicators were then measured. 4. Depending on the compounds in the mixture and their concentrations, TOL metabolism was accelerated (with BuOH), unchanged (with EtAc) or inhibited (with XYLs and MEK). Inhibition leads to an increase in blood TOL concentrations, even at authorized atmospheric concentrations, which may potentiate the effect of TOL. 5. MAs excretions are little affected by coexposure scenarios, their levels correlating well with atmospheric TOL levels. They could thus be suitable bioindicators of atmospheric TOL exposure.

Simultaneous Determination of Salicylic Acid, Jasmonic Acid, Methyl Salicylate, and Methyl Jasmonate from Ulmus pumila Leaves by GC-MS

OpenAIRE

Huang, Zhi-hong; Wang, Zhi-li; Shi, Bao-lin; Wei, Dong; Chen, Jian-xin; Wang, Su-li; Gao, Bao-jia

2015-01-01

Salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate are important phytohormones and defensive signaling compounds, so it is of great importance to determine their levels rapidly and accurately. The study uses Ulmus pumila leaves infected by Tetraneura akinire Sasaki at different stages as materials; after extraction with 80% methanol and ethyl acetate and purification with primary secondary amine (PSA) and graphitized carbon blacks (GCB), the contents of signal compounds sa...

Neutron activation determination of rhenium in shales shales and molybdenites

International Nuclear Information System (INIS)

Zajtsev, E.I.; Radinovich, B.S.

1977-01-01

Described is the technique for neutron activation determination of rhenium in shales and molybdenites with its radiochemical extraction separation by methyl-ethyl ketone. The sensitivity of the analysis is 5x10 -7 %. Experimental checking of the developed technique in reference to the analysis of shales and molybdenites was carried out. Estimated is the possibility of application of X-ray gamma-spectrometer to instrumental determination of rhenium in molybdenites

Determination of Carbonyl Compounds in Cigarette Mainstream Smoke. The CORESTA 2010 Collaborative Study and Recommended Method

Directory of Open Access Journals (Sweden)

Intorp M

2014-12-01

Full Text Available A recommended method has been developed and published by CORESTA, applicable to the quantification of selected carbonyl compounds (acetaldehyde, formaldehyde, acetone, acrolein, methyl ethyl ketone, crotonaldehyde, propionaldehyde and butyraldehyde in cigarette mainstream smoke. The method involved smoke collection in impinger traps, derivatisation of carbonyls with 2,4-dinitrophenylhydrazine (DNPH, separation of carbonyl hydrazones by reversed phase high performance liquid chromatography and detection by ultra violet or diode array.

Acetic acid removal from corn stover hydrolysate using ethyl acetate and the impact on Saccharomyces cerevisiae bioethanol fermentation.

Science.gov (United States)

Aghazadeh, Mahdieh; Ladisch, Michael R; Engelberth, Abigail S

2016-07-08

Acetic acid is introduced into cellulose conversion processes as a consequence of composition of lignocellulose feedstocks, causing significant inhibition of adapted, genetically modified and wild-type S. cerevisiae in bioethanol fermentation. While adaptation or modification of yeast may reduce inhibition, the most effective approach is to remove the acetic acid prior to fermentation. This work addresses liquid-liquid extraction of acetic acid from biomass hydrolysate through a pathway that mitigates acetic acid inhibition while avoiding the negative effects of the extractant, which itself may exhibit inhibition. Candidate solvents were selected using simulation results from Aspen Plus™, based on their ability to extract acetic acid which was confirmed by experimentation. All solvents showed varying degrees of toxicity toward yeast, but the relative volatility of ethyl acetate enabled its use as simple vacuum evaporation could reduce small concentrations of aqueous ethyl acetate to minimally inhibitory levels. The toxicity threshold of ethyl acetate, in the presence of acetic acid, was found to be 10 g L(-1) . The fermentation was enhanced by extracting 90% of the acetic acid using ethyl acetate, followed by vacuum evaporation to remove 88% removal of residual ethyl acetate along with 10% of the broth. NRRL Y-1546 yeast was used to demonstrate a 13% increase in concentration, 14% in ethanol specific production rate, and 11% ethanol yield. This study demonstrated that extraction of acetic acid with ethyl acetate followed by evaporative removal of ethyl acetate from the raffinate phase has potential to significantly enhance ethanol fermentation in a corn stover bioethanol facility. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:929-937, 2016. © 2016 American Institute of Chemical Engineers.

Anti-inflammatory activity of methyl palmitate and ethyl palmitate in different experimental rat models

Energy Technology Data Exchange (ETDEWEB)

Saeed, Noha M. [Department of Pharmacology and Toxicology, Faculty of Pharmacy, Egyptian Russian University, Cairo (Egypt); El-Demerdash, Ebtehal [Department of Pharmacology and Toxicology, Faculty of Pharmacy, Ain Shams University, Cairo (Egypt); Abdel-Rahman, Hanaa M. [Department of Pharmacology and Toxicology, Faculty of Pharmacy, Egyptian Russian University, Cairo (Egypt); Algandaby, Mardi M. [Department of Biology (Botany), Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia); Al-Abbasi, Fahad A. [Department of Biochemistry, Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia); Abdel-Naim, Ashraf B., E-mail: abnaim@pharma.asu.edu.eg [Department of Pharmacology and Toxicology, Faculty of Pharmacy, Ain Shams University, Cairo (Egypt)

2012-10-01

Methyl palmitate (MP) and ethyl palmitate (EP) are naturally occurring fatty acid esters reported as inflammatory cell inhibitors. In the current study, the potential anti-inflammatory activity of MP and EP was evaluated in different experimental rat models. Results showed that MP and EP caused reduction of carrageenan-induced rat paw edema in addition to diminishing prostaglandin E2 (PGE2) level in the inflammatory exudates. In lipopolysaccharide (LPS)-induced endotoxemia in rats, MP and EP reduced plasma levels of tumor necrosis factor-α (TNF-α) and interleukin-6 (IL-6). MP and EP decreased NF-κB expression in liver and lung tissues and ameliorated histopathological changes caused by LPS. Topical application of MP and EP reduced ear edema induced by croton oil in rats. In the same animal model, MP and EP reduced neutrophil infiltration, as indicated by decreased myeloperoxidase (MPO) activity. In conclusion, this study demonstrates the effectiveness of MP and EP in combating inflammation in several experimental models. -- Highlights: ► Efficacy of MP and EP in combating inflammation was displayed in several models. ► MP and EP reduced carrageenan-induced rat paw edema and prostaglandin E2 level. ► MP and EP decreased TNF-α and IL-6 levels in experimental endotoxemia. ► MP and EP reduced NF-κB expression and histological changes in rat liver and lung. ► MP and EP reduced croton oil-induced ear edema and neutrophil infiltration.

Uranium reextraction from D2EHPA-TOPO solvent

International Nuclear Information System (INIS)

Duarte Neto, J.

1985-01-01

A comparative study for recovering uranium from the solvent D 2 EHPA-TOPO (di-2-ethyl hexyl phosphoric acid - tri-n-octyl phosphine oxide) with ammonium carbonate and sodium carbonate solutions has been made. The paper discusses the precipitation of iron during stripping and the extracctant solubilization in the aqueous phases. Continuous tests showed that uranium is efficiently stripped from the solvent by using both solutions and that the choice of a specific system is dependent on the uranium precipitation mechanism to be employed. (Author) [pt

Evaluation of ethyl lactate as solvent in Fenton oxidation for the remediation of total petroleum hydrocarbon (TPH)-contaminated soil.

Science.gov (United States)

Jalilian Ahmadkalaei, Seyedeh Pegah; Gan, Suyin; Ng, Hoon Kiat; Abdul Talib, Suhaimi

2017-07-01

Due to the health and environmental risks posed by the presence of petroleum-contaminated areas around the world, remediation of petroleum-contaminated soil has drawn much attention from researchers. Combining Fenton reaction with a solvent has been proposed as a novel way to remediate contaminated soils. In this study, a green solvent, ethyl lactate (EL), has been used in conjunction with Fenton's reagents for the remediation of diesel-contaminated soil. The main aim of this research is to determine how the addition of EL affects Fenton reaction for the destruction of total petroleum hydrocarbons (TPHs) within the diesel range. Specifically, the effects of different parameters, including liquid phase volume-to-soil weight (L/S) ratio, hydrogen peroxide (H 2 O 2 ) concentration and EL% on the removal efficiency, have been studied in batch experiments. The results showed that an increase in H 2 O 2 resulted in an increase in removal efficiency of TPH from 68.41% at H 2 O 2  = 0.1 M to 90.21% at H 2 O 2  = 2 M. The lowest L/S, i.e. L/S = 1, had the highest TPH removal efficiency of 85.77%. An increase in EL% up to 10% increased the removal efficiency to 96.74% for TPH, and with further increase in EL%, the removal efficiency of TPH decreased to 89.6%. EL with an optimum value of 10% was found to be best for TPH removal in EL-based Fenton reaction. The power law and pseudo-first order equations fitted well to the experimental kinetic data of Fenton reactions.

Solvent-free microwave-mediated Michael addition reactions

Indian Academy of Sciences (India)

Unknown

obviously difficult to scale up. In this context ... eco-friendly features such as, (i) no solvent is required to conduct the ... water soluble, addition of reaction mixture after com- ..... Yield: 855 mg (89%; viscous liquid). 3.4 Ethyl .... Jung M E 1993 Comprehensive organic synthesis ... Leshcheva I F and Bundel Y G 1997 Mendeleev.

Solvent-extraction methods applied to the chemical analysis of uranium. III. Study of the extraction with inert solvents

International Nuclear Information System (INIS)

Vera Palomino, J.; Palomares Delgado, F.; Petrement Eguiluz, J. C.

1964-01-01

The extraction of uranium on the trace level is studied by using tributylphosphate as active agent under conditions aiming the attainment of quantitative extraction by means of a single step process using a number of salting-out agents and keeping inside the general lines as reported in two precedent papers. Two inert solvents were investigated, benzene and cyclohexane, which allowed to derive the corresponding empirical equations describing the extraction process and the results obtained were compared with those previously reported for solvents which, like ethyl acetate and methylisobuthylketone, favour to a more or less extend the extraction of uranium. (Author) 4 refs

KH 2PO4 as a novel catalyst for regioselective monobromination of aralkyl ketones using N-bromosuccinimide: a green methodology

Directory of Open Access Journals (Sweden)

P. Md. Khaja Mohinuddin

2015-08-01

Full Text Available A simple, regioselective and green method has been developed for the preparation of monobrominated ketones from various aralkyl ketones by using N-bromosuccinimide in presence of KH 2PO 4 in EtOH at reflux temperature. The present method is of short reaction time and simple with excellent isolated yields of products. The use of eco-friendly solvent, reuse of organic waste (succinimide and recyclable catalyst used for 4 times without loss of activity are advantageous. This is the first example of the use of KH 2PO 4 as a useful catalyst in organohalogen chemistry and the present method meets reduce-reuse-recycle (RRR principle towards development of green protocol.

Modified nanocrystal cellulose/fluorene-containing sulfonated poly(ether ether ketone ketone) composites for proton exchange membranes

Science.gov (United States)

Wei, Yingcong; Shang, Yabei; Ni, Chuangjiang; Zhang, Hanyu; Li, Xiaobai; Liu, Baijun; Men, Yongfeng; Zhang, Mingyao; Hu, Wei

2017-09-01

Highly sulfonated poly(ether ether ketone ketone)s (SFPEEKKs) with sulfonation degrees of 2.34 (SFPEEKK5) and 2.48 (SFPEEKK10) were synthesized through the direct sulfonation of a fluorene-containing poly(ether ether ketone ketone) under a relatively mild reaction condition. Using the solution blending method, sulfonated nanocrystal cellulose (sNCC)-enhanced SFPEEKK composites (SFPEEKK/sNCC) were successfully prepared for investigation as proton exchange membranes. Transmission electron microscopy showed that sNCC was uniformly distributed in the composite membranes. The properties of the composite membranes, including thermal stability, mechanical properties, water uptake, swelling ratio, oxidative stability and proton conductivity were thoroughly evaluated. Results indicated that the insertion of sNCC could contribute to water management and improve the mechanical performance of the membranes. Notably, the proton conductivity of SFPEEKK5/sNCC-5 was as high as 0.242 S cm-1 at 80 °C. All data proved the potential of SFPEEKK/sNCC composites for proton exchange membranes in medium-temperature fuel cells.

Catalytic enantioselective Reformatsky reaction with ketones

NARCIS (Netherlands)

Fernandez-Ibanez, M. Angeles; Macia, Beatriz; Minnaard, Adriaan J.; Feringa, Ben L.

2008-01-01

Chiral tertiary alcohols were obtained with good yields and enantioselectivities via a catalytic Reformatsky reaction with ketones, including the challenging diaryl ketones, using chiral BINOL derivatives.

Antifeedant Activty Of Different Organic Solvent Crude Extracts Of ...

African Journals Online (AJOL)

The antifeedant activity of different organic solvents (acetone, carbon tetrachloride, chloroform, diethyl ether and ethyl alcohol) crude extracts of latex of Euphorbia hirta (family Euphobiaceae) against Limicolaria aurora was investigated, and compared with a control, using pawpaw, (Carica papaya) as bait, at a concentration ...

Solution Properties of Water-Soluble “Smart” Poly(N-acryloyl-N′-ethyl piperazine-co-methyl methacrylate

Directory of Open Access Journals (Sweden)

G. Roshan Deen

2012-01-01

Full Text Available Water-soluble copolymers of N-acryloyl-N′-ethylpiperazine (AcrNEP with methyl methacrylate (MMA were synthesized to high conversion by free-radical solution polymerization. The composition of the copolymers was determined using Fourier Transform Infra-red Spectroscopy (FTIR. Copolymers containing AcrNEP content above 44 mol% were readily soluble in water and exhibited the critical solution temperature behavior. The copolymers were strongly responsive to changes in pH of the external medium due to the presence of tertiary amine functions that could be protonated at low pH. The influence of various factors such as copolymer composition, pH, temperature, salt and surfactant concentration on the LCST of the copolymers were systematically studied. The intrinsic viscosity of the copolymers in dimethyl formamide decreased with increase in temperature due to a decrease in thermodynamic affinity between polymer chains and solvent molecules. The viscosity behavior of the copolymers in sodium chloride solution was similar to that of classical polyelectrolytes and hydrophobically modified polyacrylate systems.

Rhodium-catalyzed Asymmetric Hydrogenation of α-Dehydroamino Ketones: A General Approach to Chiral α-amino Ketones.

Science.gov (United States)

Gao, Wenchao; Wang, Qingli; Xie, Yun; Lv, Hui; Zhang, Xumu

2016-01-01

Rhodium/DuanPhos-catalyzed asymmetric hydrogenation of aliphatic α-dehydroamino ketones has been achieved and afforded chiral α-amino ketones in high yields and excellent enantioselectives (up to 99 % ee), which could be reduced further to chiral β-amino alcohols by LiAlH(tBuO)3 with good yields. This protocol provides a readily accessible route for the synthesis of chiral α-amino ketones and chiral β-amino alcohols. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fragrance material review on 3-methyl-5-(2,2,3-trimethyl-3-cyclopenten-1-yl)pent-3-en-2-one.

Science.gov (United States)

Scognamiglio, J; Letizia, C S; Api, A M

2013-12-01

A toxicologic and dermatologic review of 3-methyl-5-(2,2,3-trimethyl-3-cyclopenten-1-yl)pent-3-en-2-one when used as a fragrance ingredient is presented. 3-Methyl-5-(2,2,3-trimethyl-3-cyclopenten-1-yl)pent-3-en-2-one is a member of the fragrance structural group Alkyl Cyclic Ketones. These fragrances can be described as being composed of an alkyl, R1, and various substituted and bicyclic saturated or unsaturated cyclic hydrocarbons, R2, in which one of the rings may include up to 12 carbons. Alternatively, R2 may be a carbon bridge of C2-C4 carbon chain length between the ketone and cyclic hydrocarbon. This review contains a detailed summary of all available toxicology and dermatology papers that are related to this individual fragrance ingredient and is not intended as a stand-alone document. Available data for 3-methyl-5-(2,2,3-trimethyl-3-cyclopenten-1-yl)pent-3-en-2-one were evaluated then summarized and includes physical properties, acute toxicity, skin irritation, mucous membrane (eye) irritation, sensitization, phototoxicity, photoallergy, and genotoxicity data. A safety assessment of the entire Alkyl Cyclic Ketones will be published simultaneously with this document; please refer to Belsito et al. (Belsito, D., Bickers, D., Bruze, M., Calow, P., Dagli, M., Fryer, A.D., Greim, H., Miyachi, Y., Saurat, J.H., Sipes, I.G., 2013. A Toxicologic and Dermatologic Assessment of Alkyl Cyclic Ketones when used as fragrance ingredients. Submitted for publication) for an overall assessment of the safe use of this material and all Alkyl Cyclic Ketones in fragrances. Copyright © 2013 Elsevier Ltd. All rights reserved.

Sulfonated poly(ether ether ketone) membranes for electric double layer capacitors

International Nuclear Information System (INIS)

Kim, Wan Ju; Kim, Dong-Won

2008-01-01

Sulfonated poly(ether ether ketone) (S-PEEK) with different degree of sulfonation (DS) has been prepared and evaluated as a proton conducting membrane for electric double layer capacitor (EDLC). The polymer electrolytes prepared with S-PEEK membrane exhibited ionic conductivities about 1.2 x 10 -3 -4.5 x 10 -3 S cm -1 at room temperature, which depended on both soaking solvent and degree of sulfonation. The quasi-solid-state EDLCs consisted of activated carbon electrodes and S-PEEK membrane were assembled, and their electrochemical characteristics were studied by cyclic voltammetry and charge-discharge cycle tests. The effect of DS on the electrochemical performances of EDLCs has been investigated

Synthesis of New Functionalized Indoles Based on Ethyl Indol-2-carboxylate

Directory of Open Access Journals (Sweden)

Ahmed T. A. Boraei

2016-03-01

Full Text Available Successful alkylations of the nitrogen of ethyl indol-2-carboxylate were carried out using aq. KOH in acetone. The respective N-alkylated acids could be obtained without separating the N-alkylated esters by increasing the amount of KOH and water. The use of NaOMe in methanol led to transesterification instead of the alkylation, while the use of NaOEt led to low yields of the N-alkylated acids. Hydrazinolysis of the ester gave indol-2-carbohydrazide which then was allowed to react with different aromatic aldehydes and ketones in ethanol catalyzed by acetic acid. Indol-2-thiosemicarbazide was used in a heterocyclization reaction to form thiazoles. The new structures were confirmed using NMR, mass spectrometry and X-ray single crystal analysis.

Enzymatic production of biodiesel from microalgal oil using ethyl acetate as an acyl acceptor.

Science.gov (United States)

Alavijeh, Razieh Shafiee; Tabandeh, Fatemeh; Tavakoli, Omid; Karkhane, Aliasghar; Shariati, Parvin

2015-01-01

Microalgae have become an important source of biomass for biodiesel production. In enzymatic transesterification reaction, the enzyme activity is decreased in presence of alcohols. The use of different acyl acceptors such as methyl/ethyl acetate is suggested as an alternative and effective way to overcome this problem. In this study, ethyl acetate was used for the first time in the enzymatic production of biodiesel by using microalga, Chlorella vulgaris, as a triglyceride source. Enzymatic conversion of such fatty acids to biodiesel was catalyzed by Novozym 435 as an efficient immobilized lipase which is extensively used in biodiesel production. The best conversion yield of 66.71% was obtained at the ethyl acetate to oil molar ratio of 13:1 and Novozym 435 concentration of 40%, based on the amount of oil, and a time period of 72 h at 40℃. The results showed that ethyl acetate have no adverse effect on lipase activity and the biodiesel amount was not decreased even after seven transesterification cycles, so ethyl acetate has a great potential to be substituted for short-chain alcohols in transesterification reaction.

A laminar flame investigation of 2-butanone, and the combustion-related intermediates formed through its oxidation

KAUST Repository

Hemken, Christian

2016-06-28

2-Butanone (methyl ethyl ketone) is a high-octane next-generation biofuel candidate synthesized through microbiological pathways from biomass. The flame structure and species formed in 2-butanone combustion are of interest when further considering this compound for use as a fuel. Thus species profiles within a fuel-rich laminar premixed flat flame of 2-butanone were measured. Two experiments which used different facilities and measurement techniques were combined i.e. the first using electron ionization molecular-beam mass spectrometry (MBMS) and the second relied on synchrotron-generated vacuum UV photoionization MBMS. Very good agreement between both measurements was obtained. The experiments identified the formation of a number of toxic oxygenated intermediates such as methyl vinyl ketone (MVK) acetaldehyde and formaldehyde. 2- Butanone showed the lowest overall concentrations for species that could contribute to potentially hazardous volatile emissions underlining its attraction as a fuel also from this perspective.

A laminar flame investigation of 2-butanone, and the combustion-related intermediates formed through its oxidation

KAUST Repository

Hemken, Christian; Burke, Ultan; Graf, Isabelle; Ruwe, Lena; Park, Sungwoo; Sarathy, Mani; Heufer, K. Alexander; Kohse-Hö inghaus, Katharina

2016-01-01

2-Butanone (methyl ethyl ketone) is a high-octane next-generation biofuel candidate synthesized through microbiological pathways from biomass. The flame structure and species formed in 2-butanone combustion are of interest when further considering this compound for use as a fuel. Thus species profiles within a fuel-rich laminar premixed flat flame of 2-butanone were measured. Two experiments which used different facilities and measurement techniques were combined i.e. the first using electron ionization molecular-beam mass spectrometry (MBMS) and the second relied on synchrotron-generated vacuum UV photoionization MBMS. Very good agreement between both measurements was obtained. The experiments identified the formation of a number of toxic oxygenated intermediates such as methyl vinyl ketone (MVK) acetaldehyde and formaldehyde. 2- Butanone showed the lowest overall concentrations for species that could contribute to potentially hazardous volatile emissions underlining its attraction as a fuel also from this perspective.

Synthesis and in vivo evaluation of [O-methyl-{sup 11}C](2R,4R)-4-hydroxy-2-[2-[2-[2-(3-methoxy)phenyl]ethyl]phenoxy] ethyl-1-methylpyrrolidine as a 5-HT{sub 2A} receptor PET ligand

Energy Technology Data Exchange (ETDEWEB)

Kumar, J.S. Dileep [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Div. of Brain Imaging, Dept. of Neuroscience, New York State Psychiatric Institute, New York, NY 10032 (United States)]. E-mail: dk2038@columbia.edu; Prabhakaran, Jaya [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States); Erlandsson, Kjell [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Dept. of Radiology, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States); Majo, Vattoly J. [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States); Simpson, Norman R. [Dept. of Radiology, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States); Pratap, Mali [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Div. of Brain Imaging, Dept. of Neuroscience, New York State Psychiatric Institute, New York, NY 10032 (United States); Heertum, Ronald L. van [Dept. of Radiology, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States); Mann, J. John [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Dept. of Radiology, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Div. of Brain Imaging, Dept. of Neuroscience, New York State Psychiatric Institute, New York, NY 10032 (United States); Parsey, Ramin V. [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Div. of Brain Imaging, Dept. of Neuroscience, New York State Psychiatric Institute, New York, NY 10032 (United States)

2006-05-15

The serotonin{sub 2A} (5-HT{sub 2A}) receptor is implicated in the pathophysiology of schizophrenia and mood disorders, and in vivo studies of this receptor would be of value in studying the pathophysiology of these disorders and in measuring the relationship of clinical response to receptor occupancy for 5-HT{sub 2A} antagonists such as atypical antipsychotics. Therefore, (2R,4R)-4-hydroxy-2-[2-[2-[2-(3-methoxy)-phenyl]ethyl] phenoxy]ethyl-1-methylpyrrolidine (MPM) (13), a selective and high-affinity (K {sub i}=0.79 nM) 5HT{sub 2A} antagonist, has been radiolabeled with carbon-11 by O-methylation of the corresponding desmethyl analogue (2R,4R)-4-hydroxy-2-[2-[2-[2-(3-hydroxy)phenyl]ethyl]phenoxy] ethyl-1-methylpyrrolidine (12) with [{sup 11}C]methyltriflate in order to determine the suitability of [{sup 11}C]MPM to quantify 5-HT{sub 2A} in living brain using PET. Desmethyl-MPM 12 and standard MPM were prepared, starting from 3-hydroxymethylphenol (2), in excellent yield. The yield obtained for radiolabeling was 40{+-}5% (EOB), and the total synthesis time was 30 min at EOS. PET studies with [{sup 11}C]MPM in baboon showed a distribution in the brain consistent with the known distribution of 5-HT{sub 2A} receptors. The time-activity curves for the high-binding regions peaked at {approx}45 min after injection. Blocking studies with M100907 demonstrated not only 38-57% blocking of tracer binding in brain regions known to have 5-HT{sub 2A} receptors but also 38% blocking in cerebellum, which has a low 5-HT{sub 2A} receptor concentration. Although [{sup 11}C]MPM exhibits appropriate kinetics in baboon for imaging 5-HT{sub 2A} receptors, its specific binding in cerebellum and higher proportion of nonspecific binding limit its usefulness for the in vivo quantification of 5-HT{sub 2A} receptors with PET.

Solvent effect on the synthesis of clarithromycin: A molecular dynamics study

Science.gov (United States)

Duran, Dilek; Aviyente, Viktorya; Baysal, Canan

2004-02-01

Clarithromycin (6- O-methylerythromycin A) is a 14-membered macrolide antibiotic which is active in vitro against clinically important gram-positive and gram-negative bacteria. The selectivity of the methylation of the C-6 OH group is studied on erythromycin A derivatives. To understand the effect of the solvent on the methylation process, detailed molecular dynamics (MD) simulations are performed in pure DMSO, pure THF and DMSO:THF (1:1) mixture by using the anions at the C-6, C-11 and C-12 positions of 2',4''-[ O-bis(TMS)]erythromycin A 9-[ O-(dimethylthexylsilyl)oxime] under the assumption that the anions are stable on the sub-nanosecond time scale. The conformations of the anions are not affected by the presence of the solvent mixture. The radial distribution functions are computed for the distribution of different solvent molecules around the `O-' of the anions. At distances shorter than 5 Å, DMSO molecules are found to cluster around the C-11 anion, whereas the anion at the C-12 position is surrounded by the THF molecules. The anion at the C-6 position is not blocked by the solvent molecules. The results are consistent with the experimental finding that the methylation yield at the latter position is increased in the presence of a DMSO:THF (1:1) solvent mixture. Thus, the effect of the solvent in enhancing the yield during the synthesis is not by changing the conformational properties of the anions, but rather by creating a suitable environment for methylation at the C-6 position.

Conducting polymers of octanoic acid 2-thiophen-3-yl-ethyl ester and their electrochromic properties

International Nuclear Information System (INIS)

Camurlu, Pinar; Cirpan, Ali; Toppare, Levent

2005-01-01

Octanoic acid 2-thiophen-3-yl-ethyl ester was synthesized via the reaction of 3-thiophene ethanol with octanoyl chloride. The resulting monomer was electrochemically homopolymerized in the presence of tetrabutylammonium tetrafluoroborate as the supporting electrolyte, in the acetonitrile/borontrifluoride ethyl ether solvent system. The resulting polymer was characterized using various experimental techniques. Spectroelectrochemistry analysis of the homopolymer reflects electronic transitions at 434, ∼800 and ∼1100 nm, revealing π-π* transition, polaron and bipolaron band formation, respectively, leading to esthetically pleasing color changes between transmissive yellow and blue, with reasonable switching times

GC-MS study of Nigella sativa (seeds fatty oil

Directory of Open Access Journals (Sweden)

Mehta, B. K.

2002-06-01

Full Text Available The GC-MS study of N. sativa (seeds fatty oil revealed the presence of 26 compounds which were identified as methyl hept-6-enoate,1-phenylhepta-2,4-dione, pentadecane, hexadec-1-ene, 1-phenyldecan-2-one, octadec-1-ene, octadecane, methyl pentadecanoate, bis(3-chlorophenyl ketone, diethyl phthalate, ethyl octadec-7-enoate, methyl octadecanoate, tricos-9-ene, octadeca-9,12-dienoic acid, hexadecanoic acid, methyl hexadecanoate, methyl octadec-15-enoate, henicosan-10-one, 2-methyl octadecanoic acid, docos-1-ene, ethyl octadecanoate, methyl octadecanoate, pentacos-5-ene,12-methyltricosane, dibutyl phthalate and 2-methyltetracosane.El estudio por GC-MS del aceite de la semilla de Nigella sativa reveló la presencia de 26 compuestos los cuales fueron identificados como: hept-6-enoato de metilo, 1-fenilhepta-2,4-diona, pentadecano, hexadec-1-eno, 1-fenildecan-2-ona, octadec-1-eno, octadecano, pentadecanoato de metilo, bis(3-clorofenil cetona, ftalato de dietilo, octadec-7-enoato de etilo, octadecanoato de metilo, tricos-9-eno, ácido octadeca-9,12-dienoico, ácido hexadecanoico, hexadecanoato de metilo, octadec-15-enoato de metilo, henicosan-10-ona, ácido 2-metil octadecanoico, docos-1-eno, octadecanoato de etilo, octadecanoato de metilo, pentacos-5-eno, 12-metiltricosano, ftalato de dibutilo y 2-metiltetracosano.

Simultaneous Determination of Salicylic Acid, Jasmonic Acid, Methyl Salicylate, and Methyl Jasmonate from Ulmus pumila Leaves by GC-MS

Directory of Open Access Journals (Sweden)

Zhi-hong Huang

2015-01-01

Full Text Available Salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate are important phytohormones and defensive signaling compounds, so it is of great importance to determine their levels rapidly and accurately. The study uses Ulmus pumila leaves infected by Tetraneura akinire Sasaki at different stages as materials; after extraction with 80% methanol and ethyl acetate and purification with primary secondary amine (PSA and graphitized carbon blacks (GCB, the contents of signal compounds salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate were determined by GC-MS. The results showed that the level of salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate increased remarkably in U. pumila once infected by T. akinire Sasaki, but the maximums of these four compounds occurred at different times. Salicylic acid level reached the highest at the early stage, and jasmonic acid level went to the maximum in the middle stage; by contrast, change of content of methyl salicylate and methyl jasmonate was the quite opposite.

Simultaneous Determination of Salicylic Acid, Jasmonic Acid, Methyl Salicylate, and Methyl Jasmonate from Ulmus pumila Leaves by GC-MS.

Science.gov (United States)

Huang, Zhi-Hong; Wang, Zhi-Li; Shi, Bao-Lin; Wei, Dong; Chen, Jian-Xin; Wang, Su-Li; Gao, Bao-Jia

2015-01-01

Salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate are important phytohormones and defensive signaling compounds, so it is of great importance to determine their levels rapidly and accurately. The study uses Ulmus pumila leaves infected by Tetraneura akinire Sasaki at different stages as materials; after extraction with 80% methanol and ethyl acetate and purification with primary secondary amine (PSA) and graphitized carbon blacks (GCB), the contents of signal compounds salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate were determined by GC-MS. The results showed that the level of salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate increased remarkably in U. pumila once infected by T. akinire Sasaki, but the maximums of these four compounds occurred at different times. Salicylic acid level reached the highest at the early stage, and jasmonic acid level went to the maximum in the middle stage; by contrast, change of content of methyl salicylate and methyl jasmonate was the quite opposite.

Activity coefficients at infinite dilution measurements for organic solutes and water in the ionic liquid 1-ethyl-3-methylimidazolium tetracyanoborate

International Nuclear Information System (INIS)

Domanska, Urszula; Krolikowska, Marta; Acree, William E.; Baker, Gary A.

2011-01-01

Research highlights: → Measurements of activity coefficients at infinite dilution using GLC. → 36 organic solvents and water in the ionic liquid 1-ethyl-3-methylimidazolium tetracyanoborate, [EMIM][TCB]. → Possible entrainer for different separation processes. → The partial molar excess thermodynamic functions at infinite dilution were calculated. - Abstract: The activity coefficients at infinite dilution, γ 13 ∞ , for 36 solutes, including alkanes, cycloalkanes, alkenes, alkynes, aromatic hydrocarbons, alcohols, thiophene, tetrahydrofuran, ethers, acetone, and water, in the ionic liquid 1-ethyl-3-methylimidazolium tetracyanoborate, [EMIM][TCB], were determined by gas-liquid chromatography at temperatures from 298.15 K to 358.15 K. These values are compared to those previously published for selected solutes in the same ionic liquid. The values of the partial molar excess Gibbs free energy ΔG 1 E,∞ , enthalpy ΔH 1 E,∞ , and entropy ΔS 1 E,∞ at infinite dilution were calculated from the experimental γ 13 ∞ values obtained over the temperature range. Three gas-liquid partition coefficients, K L were calculated for all solutes and the Abraham solvation parameter model is discussed. The values of the selectivity for different separation problems were calculated from γ 13 ∞ and compared to literature values for N-methyl-2-pyrrolidinone (NMP), sulfolane, 1-decyl-3-methylimidazolium tetracyanoborate, [DMIM][TCB], and additional ionic liquids.

Partially Fluorinated Solvent as a co-solvent for the Non-aqueous Electrolyte of Li/air Battery

Science.gov (United States)

2010-11-11

ether ( MFE ) and tris(2,2,2-trifluoroethyl) phosphite (TTFP), respectively, as a co-solvent for the non-aqueous electrolyte of Li–air battery. Results...fluorinated solvents on the discharge performance of Li–air bat- tery. For this purpose, we here selectmethyl nonafluorobutyl ether ( MFE ) and tris...196, (2011) pgs. 2867-2870 14. ABSTRACT In this workwestudy methyl nonafluorobutyl ether ( MFE ) and tris(2,2,2-trifluoroethyl) phosphite (TTFP

Characterization of γ-radiation induced polymerization in ethyl methacrylate and methyl acrylate monomers solutions

Science.gov (United States)

Baccaro, Stefania; Casieri, Cinzia; Cemmi, Alessia; Chiarini, Marco; D'Aiuto, Virginia; Tortora, Mariagrazia

2017-12-01

The present work is focused on the γ-radiation induced polymerization of ethyl methacrylate (EMA) and methyl acrylate (MA) monomers mixture to obtain a co-polymer with specific features. The effect of the irradiation parameters (radiation absorbed dose, dose rate) and of the environmental atmosphere on the features of the final products was investigated. Attenuated Total Reflectance - Fourier Transform Infrared Spectroscopy (ATR-FTIR) and Nuclear Magnetic Resonance high-resolution analyses of hydrogen and carbon nuclei (1H and 13C NMR) were applied to follow the γ-induced modifications by monitoring the co-polymerization process and allowed the irradiation parameters optimization. Diffusion-Ordered NMR (DOSY-NMR) data were used to evaluate the co-polymers polydispersity and polymerization degree. Since the last parameter is strongly influenced by the γ radiation and environmental conditions, a comparison among samples prepared and irradiated in air and under nitrogen atmosphere was carried out. In presence of oxygen, higher radiation was required to obtain a full solid co-polymer since a partial amount of energy released to the samples was involved in competitive processes, i.e. oxygen-containing free radicals formation and primary radicals recombination. Irrespectively to the environmental atmosphere, more homogeneous samples in term of polymerization degree dispersion was achieved at lower dose rates. At radiation absorbed doses higher than those needed for the formation of the co-polymer, while in case of samples irradiated in air heavy depolymerization was verified, a sensible increase of the samples stability was attained if the irradiation was performed under nitrogen atmosphere.

Solvation Effect on Complexation of Alkali Metal Cations by a Calix[4]arene Ketone Derivative.

Science.gov (United States)

Požar, Josip; Nikšić-Franjić, Ivana; Cvetnić, Marija; Leko, Katarina; Cindro, Nikola; Pičuljan, Katarina; Borilović, Ivana; Frkanec, Leo; Tomišić, Vladislav

2017-09-14

The medium effect on the complexation of alkali metal cations with a calix[4]arene ketone derivative (L) was systematically examined in methanol, ethanol, N-methylformamide, N,N-dimethylformamide, dimethyl sulfoxide, and acetonitrile. In all solvents the binding of Na + cation by L was rather efficient, whereas the complexation of other alkali metal cations was observed only in methanol and acetonitrile. Complexation reactions were enthalpically controlled, while ligand dissolution was endothermic in all cases. A notable influence of the solvent on NaL + complex stability could be mainly attributed to the differences in complexation entropies. The higher NaL + stability in comparison to complexes with other alkali metal cations in acetonitrile was predominantly due to a more favorable complexation enthalpy. The 1 H NMR investigations revealed a relatively low affinity of the calixarene sodium complex for inclusion of the solvent molecule in the calixarene hydrophobic cavity, with the exception of acetonitrile. Differences in complex stabilities in the explored solvents, apart from N,N-dimethylformamide and acetonitrile, could be mostly explained by taking into account solely the cation and complex solvation. A considerable solvent effect on the complexation equilibria was proven to be due to an interesting interplay between the transfer enthalpies and entropies of the reactants and the complexes formed.

Reaction of active uranium and thorium with aromatic carbonyls and pinacols in hydrocarbon solvents

International Nuclear Information System (INIS)

Kahn, B.E.; Rieke, R.D.

1988-01-01

Highly reactive uranium and thorium metal powders have been prepared by reduction of the anhydrous metal(IV) chlorides in hydrocarbon solvents. The reduction employs the crystalline hydrocarbon-soluble reducing agent [(TMEDA)Li] 2 [Nap] (TMEDA = N,N,N',N'-tetramethylethylenediamine, Nap = naphthalene). The resulting active metal powders have been shown to be extremely reactive with oxygen-containing compounds and have been used in the reductive coupling of aromatic ketones giving tetra-arylethylenes. Reactions with pinacols have given some mechanistic insight into the ketone coupling reaction. These finely divided metal powders activate very weakly acidic C-H bonds forming metal hydrides, which can be transferred to organic substrates

Insights into the coal extractive solvent N-methyl-2-pyrrolidone + carbon disulfide

Energy Technology Data Exchange (ETDEWEB)

Santiago Aparicio; Mara J. Davila; Rafael Alcalde [University of Burgos, Burgos (Spain). Department of Chemistry

2009-03-15

A wide set of experimental and computational tools were used to characterize the N-methyl-2-pyrrolidone (NMP) + carbon disulfide mixed solvent in the full composition range. The interest in this solvent rose from its very efficient use for coal extraction through a mechanism still not fully understood. Thermophysical properties at ambient pressure together with pressure-volume-temperature (PVT) behavior were measured with the objective of providing the required data for the industrial use of the mixed fluid and to get insight into the fluid structure at the molecular level. NMR, FTIR, and solvatochromic studies were performed together with microwave dielectric relaxation spectroscopy (DRS) measurements, thus providing more information on the fluid's structure and allowing one to relate the molecular level behavior with the measured macroscopic properties. Moreover, density functional theory (DFT) and classical molecular dynamics simulations (MD) were used to obtain a detailed picture of the intermolecular interactions within the fluid, at short and long ranges, and of other relevant features leading to the structure of the studied system. The whole study leads to a fluid's picture in which carbon disulfide hinders the development of NMP/NMP intermolecular dipolar interactions, thus increasing the monomer population. We should remark that some properties reported in this work are in remarkable disagreement with previously reported studies, the most important one being the positive excess molar volume in the whole pressure-temperature range studied, which contrasts with the negative values reported in the literature. Previously reported properties are hardly justified with a coherent molecular level picture, whereas the whole collection of properties reported in this work leads to a more reasonable fluid's structure. 56 refs., 17 figs., 2 tabs.

Electrolytic preparation of sup(99m)Tc human serum albumin using tin electrodes

International Nuclear Information System (INIS)

Narasimhan, D.V.S.; Mani, R.S.

1975-01-01

A method for labelling human serum albumin [HSA] with sup(99m)Tc using electrolytically generated Sn/II/ ions has been developed. The procedure uses Sn electrodes for electrolysis and gives high labelling yields. The amount of Sn released into the final product was found to be much less than the reported toxic levels. A ready-to-use kit for obtaining sterile sup(99m)Tc HSA is described. Tin metal wires sealed in aluminium were irradiated in a CIRUS reactor at a neutron flux of 7.5x10 12 n cm -2 sec -1 for one month. The 113 Sn produced in the wire was used for tracer studies with the electrolitically labelled HSA. sup(99m)Tc in the form sodium pertechnetate in 0.9% NaCl was obtained by methyl ethyl ketone extraction from alkaline solutions of neutron irradiated 99 Mo [specific activity 50-200 mCi/g] in the solvent extraction generator developed at Isotope Division, BARC. Radiochemical purity analysis of sup(99m)Tc labelled HSA prepared by the above procedure was carried out by ascending paper chromatography on Whatman No.1 paper, and 85% methanol and 0.9% sodium chloride as solvents. (F.Gy.)

Optimization and validation of liquid chromatography and headspace-gas chromatography based methods for the quantitative determination of capsaicinoids, salicylic acid, glycol monosalicylate, methyl salicylate, ethyl salicylate, camphor and l-menthol in a topical formulation.

Science.gov (United States)

Pauwels, Jochen; D'Autry, Ward; Van den Bossche, Larissa; Dewever, Cédric; Forier, Michel; Vandenwaeyenberg, Stephanie; Wolfs, Kris; Hoogmartens, Jos; Van Schepdael, Ann; Adams, Erwin

2012-02-23

Capsaicinoids, salicylic acid, methyl and ethyl salicylate, glycol monosalicylate, camphor and l-menthol are widely used in topical formulations to relieve local pain. For each separate compound or simple mixtures, quantitative analysis methods are reported. However, for a mixture containing all above mentioned active compounds, no assay methods were found. Due to the differing physicochemical characteristics, two methods were developed and optimized simultaneously. The non-volatile capsaicinoids, salicylic acid and glycol monosalicylate were analyzed with liquid chromatography following liquid-liquid extraction, whereas the volatile compounds were analyzed with static headspace-gas chromatography. For the latter method, liquid paraffin was selected as compatible dilution solvent. The optimized methods were validated in terms of specificity, linearity, accuracy and precision in a range of 80% to 120% of the expected concentrations. For both methods, peaks were well separated without interference of other compounds. Linear relationships were demonstrated with R² values higher than 0.996 for all compounds. Accuracy was assessed by performing replicate recovery experiments with spiked blank samples. Mean recovery values were all between 98% and 102%. Precision was checked at three levels: system repeatability, method precision and intermediate precision. Both methods were found to be acceptably precise at all three levels. Finally, the method was successfully applied to the analysis of some real samples (cutaneous sticks). Copyright © 2011 Elsevier B.V. All rights reserved.

Dipyridine cobalt chloride as an efficient and chemoselective catalyst for the synthesis of 1,1-diacetates under solvent-free conditions

Directory of Open Access Journals (Sweden)

Sobhan Rezayati

2014-02-01

Full Text Available 1,1-Diacetates(acylals were prepared by direct condensation of various aldehydes with acetic anhydride using dipyridine cobalt chloride (CoPy2Cl2 as an efficient and green catalyst under solvent-free conditions at room temperature. The important features of this catalyst method are that the catalyst is solid, stable at high temperatures, soluble in water, stable in air, immiscible in common organic solvents, and low toxic and, above all, it is reusable. CoPy2Cl2 can be recycled after a simple work-up and reused at least five runs without appreciable loss of its catalytic activity. High chemo-selectivity toward aldehyde in the presence of ketones is another advantage of the present method which provides selective protection of aldehydes in their mixtures with ketones.

Modified montmorillonite as a heterogeneous catalyst in (m)ethyl esterification reaction of lauric acid; Montmorilonita modificada como catalisador heterogeneo em reacoes de esterificacao (M)etilica de acido laurico

Energy Technology Data Exchange (ETDEWEB)

Zatta, Leandro; Nepel, Angelita; Barison, Andersson; Wypych, Fernando, E-mail: wypych@ufpr.br [Departamento de Quimica, Universidade Federal do Parana (UFPR), Curitiba , PR (Brazil)

2012-07-01

Montmorillonite was modified with zirconium polyoxycations in the presence of ammonium sulphate. The material was characterized and used as a catalyst in the esterification of lauric acid, the reactions being accompanied by 2{sup 3} factorial design. Conversions of up to 95.33 and 83.35% were observed for the methyl and ethyl esterification reactions respectively, proving superior to results obtained by thermal conversion. The material was submitted to three reaction cycles and similar conversions were observed, indicating the catalyst is not significantly deactivated after reuse. The catalyst was also tested under reflux conditions, yielding a maximum conversion of 36.86%. (author)

300 area solvent evaporator interim status closure plan: Revision 2

International Nuclear Information System (INIS)

1989-02-01

This document describes activities for the closure of a hazardous waste tank treatment facility operated by the US Department of Energy-Richland Operations Office (DOE-RL) and co-operated by the Westinghouse Hanford Company (WHC). This treatment facility was a solvent evaporator located in the 300 Area of the Hanford Site, from 1975 to 1985 on behalf of DOE-RL. The 300 Area Solvent Evaporator (300 ASE) was a modified load lugger (dumpster) in which solvent wastes were evaporated. Some of the solvents were radioactively contaminated because they came from a degreaser which processed bare uranium metal billets from the N Reactor Fuel Manufacturing Facility. The waste was composed of perchloroethylene, trichloroethylene, 1,1,1-trichloroethane, ethyl acetate/bromine solution, paint shop solvents and possibly some used oil. Also, small amounts of uranium, copper, zirconium and possibly beryllium were present in the degreaser solvents as particulates. Radioactive and non-radioactive solvents were not segregated in the 300 ASE, and the entire mixture was regarded as mixed waste

Fast and efficient method for reduction of carbonyl compounds with NaBH4 /wet SiO2 under solvent free condition

International Nuclear Information System (INIS)

Zeynizadeh, Behzad; Bahyar, Tarifeh

2005-01-01

Reduction of structurally different carbonyl compounds such as aldehydes, ketones, α,β-unsaturated enals and enones, α-diketones and acyloins were accomplished efficiently by sodium borohydride in the presence of wet SiO 2 (30% m/m) under solvent free condition. The reactions were performed at room temperature or 75-80 deg C with high to excellent yields of the corresponding products. The chemoselective reduction of aldehydes over ketones was achieved successfully with this reducing system. (author)

Adding Value to Bioethanol through a Purification Process Revamp

DEFF Research Database (Denmark)

Bisgaard, Thomas; Mauricio Iglesias, Miguel; Huusom, Jakob Kjøbsted

2017-01-01

distillation columns and a dehydration step using molecular sieves. This separation unit did not permit sufficient removal of crotonaldehyde and methanol for obtaining solvent-grade ethanol. Therefore, an additional distillation column after the dehydration step was investigated by simulation. It is operated...... at subatmospheric pressure and enables simultaneous removal of methanol, crotonaldehyde, and water in the distillate. The distillate meets the fuel-grade ethanol specifications, while the bottom product meets the solvent-grade specifications. It enables around 70% solvent-grade ethanol production and employs...... analyzed experimentally: Acetaldehyde, 1-propanal, 1-butanal, crotonaldehyde, benzaldehyde, ethyl acetate, methanol, 1-propanol, 1-butanol, 2-butanol, 2-methyl-l-propanol, 2-methyl-l-butanol, and 3-methyl-1-butanol. A simulation platform was established and evaluated with excellent agreement compared...

Diagnostic markers of urothelial cancer based on DNA methylation analysis

International Nuclear Information System (INIS)

Chihara, Yoshitomo; Hirao, Yoshihiko; Kanai, Yae; Fujimoto, Hiroyuki; Sugano, Kokichi; Kawashima, Kiyotaka; Liang, Gangning; Jones, Peter A; Fujimoto, Kiyohide; Kuniyasu, Hiroki

2013-01-01

Early detection and risk assessment are crucial for treating urothelial cancer (UC), which is characterized by a high recurrence rate, and necessitates frequent and invasive monitoring. We aimed to establish diagnostic markers for UC based on DNA methylation. In this multi-center study, three independent sample sets were prepared. First, DNA methylation levels at CpG loci were measured in the training sets (tumor samples from 91 UC patients, corresponding normal-appearing tissue from these patients, and 12 normal tissues from age-matched bladder cancer-free patients) using the Illumina Golden Gate methylation assay to identify differentially methylated loci. Next, these methylated loci were validated by quantitative DNA methylation by pyrosequencing, using another cohort of tissue samples (Tissue validation set). Lastly, methylation of these markers was analyzed in the independent urine samples (Urine validation set). ROC analysis was performed to evaluate the diagnostic accuracy of these 12 selected markers. Of the 1303 CpG sites, 158 were hyper ethylated and 356 were hypo ethylated in tumor tissues compared to normal tissues. In the panel analysis, 12 loci showed remarkable alterations between tumor and normal samples, with 94.3% sensitivity and 97.8% specificity. Similarly, corresponding normal tissue could be distinguished from normal tissues with 76.0% sensitivity and 100% specificity. Furthermore, the diagnostic accuracy for UC of these markers determined in urine samples was high, with 100% sensitivity and 100% specificity. Based on these preliminary findings, diagnostic markers based on differential DNA methylation at specific loci can be useful for non-invasive and reliable detection of UC and epigenetic field defect

Solubility and crystallization of piroxicam from different solvents in evaporative and cooling crystallizations

DEFF Research Database (Denmark)

Qu, Haiyan; Ostergaard, Iben

2018-01-01

polarities; It has been found that the solubility of piroxicam in the solvents is in the following order: chloroform > dichloromethane > acetone > ethyl acetate > acetonitrile > acetic acid > methanol > hexane. Crystallization of piroxicam from different solvents has been performed with evaporative.......Results obtained in the present work showed the stochastic nature of nucleation of different polymorphs as well as the complexity of the crystallization of a polymorphic system....

Assessment of Multiple Solvents for Extraction and Direct GC-MS Determination of the Phytochemical Inventory of Sansevieria Extrafoliar Nectar Droplets.

Science.gov (United States)

Gaylor, Michael O; Juntunen, Hope L; Hazelwood, Donna; Videau, Patrick

2018-04-01

Considerable effort has been devoted to analytical determinations of sugar and amino acid constituents of plant nectars, with the primary aim of understanding their ecological roles, yet few studies have reported more exhaustive organic compound inventories of plant nectars or extrafoliar nectars. This work evaluated the efficacy of four solvents (ethyl acetate, dichloromethane, toluene and hexane) to extract the greatest number of organic compound classes and unique compounds from extrafoliar nectar drops produced by Sansevieria spp. Aggregation of the results from each solvent revealed that 240 unique compounds were extracted in total, with 42.5% of those detected in multiple extracts. Aliphatic hydrocarbons dominated in all but the ethyl acetate extracts, with 44 unique aliphatic hydrocarbons detected in dichloromethane (DCM) extracts, followed by 41, 19 and 8 in hexane, toluene and ethyl acetate extracts, respectively. Hexane extracted the most unique compounds (79), followed by DCM (73), ethyl acetate (56) and toluene (32). Integrated total ion chromatographic peak areas of extracted compound classes were positively correlated with numbers of unique compounds detected within those classes. In addition to demonstrating that multi-solvent extraction with direct GC-MS detection is a suitable analytical approach for determining secondary nectar constituents, to the best of our knowledge, this study also represents: (i) the first attempt to inventory the secondary phytochemical constituents of Sansevieria spp. extrafoliar nectar secretions and (ii) the largest organic solvent extractable compound inventory reported for any plant matrix to date.

Ultrasonic velocities, densities, and excess molar volumes of binary mixtures of N,N-dimethyl formamide with methyl acrylate, or ethyl acrylate, or butyl acrylate, or 2-ethyl hexyl acrylate at T = 308.15 K

Energy Technology Data Exchange (ETDEWEB)

Kondaiah, M. [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar 522510, Andhra Pradesh (India); Sravana Kumar, D. [Dr. V.S. Krishna Govt. Degree College, Visakhapatnam, Andhra Pradesh (India); Sreekanth, K. [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar 522510, Andhra Pradesh (India); Krishna Rao, D., E-mail: krdhanekula@yahoo.co.in [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar 522510, Andhra Pradesh (India)

2011-12-15

Highlights: > Positive values of V{sub m}{sup E}, indicate dispersion forces between acrylic esters and DMF. > V{sub m}{sup E} values compared with Redlich-Kister polynomial. > Partial molar volumes data conclude that weak interactions exist in the systems. > Measured velocity values compared with theoretical values obtained by polynomials. - Abstract: Ultrasonic velocities, u, densities, {rho}, of binary mixtures of N,N-dimethyl formamide (DMF) with methyl acrylate (MA), ethyl acrylate (EA), butyl acrylate (BA), and 2-ethyl hexyl acrylate (EHA), including pure liquids, over the entire composition range have been measured at T = 308.15 K. Using the experimental results, the excess molar volume, V{sub m}{sup E}, partial molar volumes, V-bar {sub m,1}, V-bar{sub m,2}, and excess partial molar volumes, V-bar{sub m,1}{sup E}, V-bar{sub m,2}{sup E} have been calculated. Molecular interactions in the systems have been studied in the light of variation of excess values of calculated properties. The excess properties have been fitted to Redlich-Kister type polynomial and the corresponding standard deviations have been calculated. The positive values of V{sub m}{sup E} indicate the presence of dispersion forces between the DMF and acrylic ester molecules. Further theoretical values of sound velocity in the mixtures have been evaluated using various theories and have been compared with experimental sound velocities to verify the applicability of such theories to the systems studied. Theoretical ultrasonic velocity data have been used to study molecular interactions in the binary systems investigated.

Ferrocene Compounds. XXVI. C- and O-Ferrocenylalkylation of Methyl Salicylate

OpenAIRE

Kovač, Veronika; Rapić, Vladimir; Alagić, Jasmina; Barišić, Lidija

1999-01-01

Reaction of equimolar amounts of methyl salicylate, sodium and N,N,N-trimethylferrocylammonium iodide (1a) in ethanol gave 55% of ethyl 1-ferrocenylethyl ether (4). By refluxing a solution of 9 mmol sodium and 3 mmol of FcCHRNMe3I (1a, R = H; 1b, R = Me; 1c, R = Ph) in a large excess of methyl salicylate for 2-3 hours, the corresponding methyl 5-ferrocylsalicylates (5) (10-23%) and methyl-3-ferrocylsalicylates (6) (12-20%) were obtained. During conversion of salt 1b, besides of 5b and 6b, 20%...

Enhancement of 2,3-butanediol production by Klebsiella ...

African Journals Online (AJOL)

PRECIOUS

2009-11-16

Nov 16, 2009 ... for automatic design and analysis of the experiments, both based on Taguchi protocol. Optimal levels ... manufacture of butadiene, or to its use as an antifreeze ... butanediol yields the industrial solvent methyl ethyl ke- tone.

Investigation of diesel-ethanol blended fuel properties with palm methyl ester as co-solvent and blends enhancer

Directory of Open Access Journals (Sweden)

Mat Taib Norhidayah

2017-01-01

Full Text Available Diesel engine is known as the most efficient engine with high efficiency and power but always reported as high fuel emission. Malaysia National Automotive Policy (NAP was targeting to improve competitive regional focusing on green technology development in reducing the emission of the engine. Therefore, ethanol was introduced to reduce the emission of the engine and while increasing its performance, Palm methyl ester was introduced as blend enhancer to improve engine performance and improve diesel-ethanol blends stability. This paper aimed to study the characteristics of the blends and to prove the ability of palm-methyl-ester as co-solvent in ethanol-diesel blends. Stability and thermophysical test were carried out for different fuel compositions. The stability of diesel-ethanol blended was proved to be improved with the addition of PME at the longer period and the stability of the blends changed depending on temperature and ethanol content. Density and viscosity of diesel-ethanol-PME blends also give higher result than diesel-ethanol blends and it's proved that PME is able to increase density and viscosity of blends. Besides, heating value of the blends also increases with the increasing PME in diesel-ethanol blends.

Strigolactone analogs derived from ketones using a working model for germination stimulants as a blueprint.

Science.gov (United States)

Mwakaboko, Alinanuswe S; Zwanenburg, Binne

2011-04-01

Strigolactones are important signaling compounds in the plant kingdom. Here we focus on their germination stimulatory effect on seeds of the parasitic weeds Striga and Orobanche spp. and more particularly on the design and synthesis of new active strigolactone analogs derived from simple cyclic ketones. New analogs derived from 1-indanone, 1-tetralone, cyclopentanone, cyclohexanone and a series of substituted cyclohexanones (including carvone and pulegone) are prepared by formylation of the ketones with ethyl formate followed by coupling with a halo butenolide. Both enantiomers of the analog derived from 1-tetralone have been prepared by employing a homochiral synthon for the coupling reaction. For three other strigolactone analogs the antipodes have been obtained by chromatography on a chiral column. All analogs have an appreciable germinating activity towards seeds of Striga hermomonthica and Orobanche crenata and O. cernua. Stereoisomers having the same configuration at the D-ring as in naturally occurring strigol have a higher stimulatory effect than the corresponding antipodes. The analogs obtained from 1-indanone and 1-tetralone have an activity comparable with that of the well known stimulant GR 24. Analogs derived from 2-phenyl-cylohexanone, carvone and pulegone also have a good germinating response. The results show that the working model for designing new bioactive strigolactones is applicable.

Controlled release of beta-estradiol from PLAGA microparticles: the effect of organic phase solvent on encapsulation and release.

Science.gov (United States)

Birnbaum, D T; Kosmala, J D; Henthorn, D B; Brannon-Peppas, L

2000-04-03

To determine the effect of the organic solvent used during microparticle preparation on the in vitro release of beta-estradiol, a number of formulations were evaluated in terms of size, shape and drug delivery performance. Biodegradable microparticles of poly(lactide-co-glycolide) were prepared containing beta-estradiol that utilized dichloromethane, ethyl acetate or a mixture of dichloromethane and methanol as the organic phase solvent during the particle preparation. The drug delivery behavior from the microparticles was studied and comparisons were made of their physical properties for different formulations. The varying solubilities of beta-estradiol and poly(lactide-co-glycolide) in the solvents studied resulted in biodegradable microparticles with very different physical characteristics. Microparticles prepared from solid suspensions of beta-estradiol using dichloromethane as the organic phase solvent were similar in appearance to microparticles prepared without drug. Microparticles prepared from dichloromethane/methanol solutions appeared transparent to translucent depending on the initial amount of drug used in the formulation. Microparticles prepared using ethyl acetate appeared to have the most homogeneous encapsulation of beta-estradiol, appearing as solid white spheres regardless of initial drug content. Studies showed that microparticles prepared from either ethyl acetate or a mixture of dichloromethane and methanol gave a more constant release profile of beta-estradiol than particles prepared using dichloromethane alone. For all formulations, an initial burst of release increased with increasing drug loading, regardless of the organic solvent used.

Validation of methodologies for the analysis of lead and methyl-ether in gasoline, using the techniques of atomic emission with plasma source coupled inductively and micellar liquid chromatography

International Nuclear Information System (INIS)

Redondo Escalante, M.

1995-01-01

This study established and optimized the experimental variables for the lead quantization through the Icp-Aes technique, in aqueous media. A comparative study of several proposal methods, that appears in the literature for the extraction in aqueous media of the lead in gasoline was made. It determined that it is not possible, to make this procedure using the reaction of hydrolysis of tetraethyl lead. The op tim conditions were established, for the lead quantization in gasoline, using methyl-isobutyl-ketone and also ethanol as dis solvents. The conditions of the proposed methodologies were optimized, and the variables of analytical performance were defined. It was demonstrated, that it is possible to prepare lead dissolution patterns, in organic media, starting from inorganic salts of this metal. The techniques of chromatography of gases and of liquid chromatography of high pressure, in the analysis of methyl-ter butyl-ether (Mtbe), were compared. It demonstrated that it is possible, to quantize the Mtbe through the HPLC technique, and it found that the 'micellar' liquid chromatography. (author) [es

Captive solvent methods for fast, simple carbon-11 radioalkylations

International Nuclear Information System (INIS)

Jewett, D.M.; Mangner, T.J.; Watkins, G.L.

1991-01-01

Carbon-11 labeled radiopharmaceuticals for receptor studies usually require final purification by high performance liquid chromatography (HPLC). A significant simplification of the apparatus is possible if the radiolabeling reaction can be done directly in the HPLC injection circuit. Captive solvent methods in which the reaction is done in a small volume of solvent absorbed in a porous solid matrix are a general approach to this problem. For N-methylations with [ 11 C] methyl iodide, a basic catalyst may be incorporated in the polymeric or alumina solid phase. Reaction volumes are from 20 to 100 ML. Often no heating or cooling of the reaction column is necessary. The syntheses of [ 11 C]PK11195 and [ 11 C] flumazenil are described to illustrate some of the advantages and limitations of captive solvent methods

Novel proton exchange membranes based on structure-optimized poly(ether ether ketone ketone)s and nanocrystalline cellulose

Science.gov (United States)

Ni, Chuangjiang; Wei, Yingcong; Zhao, Qi; Liu, Baijun; Sun, Zhaoyan; Gu, Yan; Zhang, Mingyao; Hu, Wei

2018-03-01

Two sulfonated fluorenyl-containing poly(ether ether ketone ketone)s (SFPEEKKs) were synthesized as the matrix of composite proton exchange membranes by directly sulfonating copolymer precursors comprising non-sulfonatable fluorinated segments and sulfonatable fluorenyl-containing segments. Surface-modified nanocrystalline cellulose (NCC) was produced as the "performance-enhancing" filler by treating the microcrystalline cellulose with acid. Two families of SFPEEKK/NCC nanocomposite membranes with various NCC contents were prepared via a solution-casting procedure. Results revealed that the insertion of NCC at a suitable ratio could greatly enhance the proton conductivity of the pristine membranes. For example, the proton conductivity of SFPEEKK-60/NCC-4 (SFPEEKK with 60% fluorenyl segments in the repeating unit, and inserted with 4% NCC) composite membrane was as high as 0.245 S cm-1 at 90 °C, which was 61.2% higher than that of the corresponding pure SFPEEKK-60 membrane. This effect could be attributed to the formation of hydrogen bond networks and proton conduction paths through the interaction between -SO3H/-OH groups on the surface of NCC particles and -SO3H groups on the SFPEEKK backbones. Furthermore, the chemically modified NCC filler and the optimized chemical structure of the SFPEEKK matrix also provided good dimensional stability and mechanical properties of the obtained nanocomposites. In conclusion, these novel nanocomposites can be promising proton exchange membranes for fuel cells at moderate temperatures.

Radiolytic stabilization of poly(methyl methacrylate) in blends with polystyrene

International Nuclear Information System (INIS)

Lima, Ivania Soares de

2002-04-01

In this work the radiolytic stabilization of poly(methyl methacrylate) was analyzed by three radioprotective agents: polystyrene (PS) and hindered amine light stabilizers (HEALS), respectively, PMMA/PS systems, so a called polymeric blends were prepared with different compositions, where the miscibility of these blends were studied using viscometric, microscopy (SEM) and spectroscopy (FT-IR) techniques. The results show that PMMA/PS blends in the compositions below 10 wt% of PS are miscible, on films casting from solution of toluene and methyl-ethyl-ketone (1;1) mixture. On the other hand, in the composition above 10 wt% of PS, PMMA/PS blends show imminiscibility behavior. These polymer solutions were irradiated with gamma rays ( 60 Co) and viscometric, microscopic and spectroscopic experiments show gamma radiation-induced compatibilization on PMMA/PS blends on proportion 50/50 and 30/70 take place. Viscometric interaction parameters of miscible and compatibilized PMMA/PS bends were calculated in the range of - 50 kGy, with the goal to find out the polymeric interactions after irradiation of the films. G values of PMMA, PMMA/PS and PMMA+St systems were calculated in order to analyze the radioprotection of PS and St into PMMA matrix. The results show that (90/10) PMMA/PS and PMMA+1,5%St systems promote protection against the gamma the radiation-induced scissions, effect that leads to polymer degradation. Moreover, a small amount of crosslinking observed in irradiated blends has contributed to stabilize mechanical properties of PMMA films. PMMA+0,3% HALS system irradiated in doses above 60 kGy showed little stabilization of the mechanical properties of PMMA, since it was observed mechanical degradation this system. Based on these results, PS and St showed to be the best radioprotective agents to PMMA. (author)

Tar removal from biosyngas in the biomass gasification process. (Liquid + liquid) equilibrium {water + solvent (paraxylene and methyl hexadecanoate) + model molecules of tar (benzene, toluene, phenol)}

International Nuclear Information System (INIS)

Bassil, Georgio; Mokbel, Ilham; Abou Naccoul, Ramy; Stephan, Juliette; Jose, Jacques; Goutaudier, Christelle

2012-01-01

Highlights: ► (Liquid + liquid) equilibria at atmospheric pressure. ► Solubility of benzene (or toluene or phenol) in paraxylene at (303 to 343) K. ► Solubility of benzene (or toluene or phenol) in methyl palmitate or methyl hexadecanoate at (303 to 343) K. ► Correlation of LLE using NRTL model. - Abstract: Tar is generated in the process by the condensation of the gas resulting from biomass gasification. The objective of this work is a contribution to the database on thermodynamic quantity which will be useful at the operation of tar removal from aqueous medium. With this aim, (liquid + liquid) equilibrium of {water + solvent (paraxylene and methyl hexadecanoate) + model molecules of tar (benzene, toluene, phenol)} was studied at temperatures (303.2, 323.2, and 343.2) K. The data obtained were correlated with the non-random two-liquid (NRTL) model.

Influence of degree of methyl methacrylate polymerization on spectroscopic properties of ethyl 5-(4-aminophenyl)- and 5-(4-dimethylaminophenyl)-3-amino-2,4-dicyanobenzoate

International Nuclear Information System (INIS)

Józefowicz, M.; Bajorek, A.; Pietrzak, M.; Jędrzejewska, B.; Heldt, J.R.; Heldt, J.

2013-01-01

The influence of degree of methyl methacrylate (MM) polymerization on the both emission modes (LE—locally excited and ICT—intramolecular charge transfer) of the fluorescence spectrum of ethyl 5-(4-aminophenyl)-3-amino-2,4-dicyanobenzoate (EAADCy) and ethyl 5-(4-dimethylaminophenyl)-3-amino-2,4-dicyanobenzoate (EDMAADCy) has been studied using steady-state and time-resolved spectroscopic technique. The purpose of these studies was to find a relationship between the changes in the spectroscopic characteristics (fluorescence intensity, wavelength of maximum intensity, fluorescence full-width at half maximum, emission anisotropy, fluorescence decay time) of the tested compounds and degree of monomer conversion into polymer. On the basis of the experimental results, it was shown that the ICT fluorescence full-width at half maximum for EDMAADCy shows a linear dependence on the time of MM polymerization. Our findings predestine the molecule EDMAADCy to be used as fluorescence probe for monitoring the polymerization process of MM. - Highlights: ► The fluorescence excitation and emission spectra in MM possess a complex nature. ► Fluorescence decay kinetics for different degrees of polymerization of MM were investigated. ► The ICT fluorescence FWHM for EDMAADCy shows a linear dependence on the time of polymerization. ► EDMAADCy can be used as fluorescence probe for monitoring the polymerization process of MM

Rapid, efficient and solvent free microwave mediated synthesis of aldo- and ketonitrones

Directory of Open Access Journals (Sweden)

Loredana Maiuolo

2016-01-01

Full Text Available A library of C-alkyl and C-aryl nitrones has been obtained by direct condensation of primary N-substituted hydroxylamine hydrochlorides with various aldehydes and ketones without catalysts or base. The synthetic procedure, performed under MW irradiation in the absence of solvent, does not require the presence of a base, is fast, clean, high-yielding and characterized by simple work-up.

Homologation Reaction of Ketones with Diazo Compounds.

Science.gov (United States)

Candeias, Nuno R; Paterna, Roberta; Gois, Pedro M P

2016-03-09

This review covers the addition of diazo compounds to ketones to afford homologated ketones, either in the presence or in the absence of promoters or catalysts. Reactions with diazoalkanes, aryldiazomethanes, trimethylsilyldiazomethane, α-diazo esters, and disubstituted diazo compounds are covered, commenting on the complex regiochemistry of the reaction and the nature of the catalysts and promoters. The recent reports on the enantioselective version of ketone homologation reactions are gathered in one section, followed by reports on the use of cyclic ketones ring expansion in total synthesis. Although the first reports of this reaction appeared in the literature almost one century ago, the recent achievements, in particular, for the asymmetric version, forecast the development of new breakthroughs in the synthetically valuable field of diazo chemistry.

Reduction of Aldehydes and Ketones by Sodium Dithionite

NARCIS (Netherlands)

Vries, Johannes G. de; Kellogg, Richard M.

1980-01-01

Conditions have been developed for the effective reduction of aldehydes and ketones by sodium dithionite, Na2S2O4. Complete reduction of simple aldehydes and ketones can be achieved with excess Na2S2O4 in H2O/dioxane mixtures at reflux temperature. Some aliphatic ketones, for example, pentanone and

Novel fatty acid methyl esters from the actinomycete Micromonospora aurantiaca

Science.gov (United States)

Bruns, Hilke; Riclea, Ramona

2011-01-01

Summary The volatiles released by Micromonospora aurantiaca were collected by means of a closed-loop stripping apparatus (CLSA) and analysed by GC–MS. The headspace extracts contained more than 90 compounds from different classes. Fatty acid methyl esters (FAMEs) comprised the major compound class including saturated unbranched, monomethyl and dimethyl branched FAMEs in diverse structural variants: Unbranched, α-branched, γ-branched, (ω−1)-branched, (ω−2)-branched, α- and (ω−1)-branched, γ- and (ω−1)-branched, γ- and (ω−2)-branched, and γ- and (ω−3)-branched FAMEs. FAMEs of the last three types have not been described from natural sources before. The structures for all FAMEs have been suggested based on their mass spectra and on a retention index increment system and verified by the synthesis of key reference compounds. In addition, the structures of two FAMEs, methyl 4,8-dimethyldodecanoate and the ethyl-branched compound methyl 8-ethyl-4-methyldodecanoate were deduced from their mass spectra. Feeding experiments with isotopically labelled [2H10]leucine, [2H10]isoleucine, [2H8]valine, [2H5]sodium propionate, and [methyl-2H3]methionine demonstrated that the responsible fatty acid synthase (FAS) can use different branched and unbranched starter units and is able to incorporate methylmalonyl-CoA elongation units for internal methyl branches in various chain positions, while the methyl ester function is derived from S-adenosyl methionine (SAM). PMID:22238549

Analysis of solvent extracts from coal liquefaction in a flowing solvent reactor

Energy Technology Data Exchange (ETDEWEB)

Li, Wen-Ying; Feng, Jie; Xie, Ke-Chang [Key Laboratory of Coal Science and Technology, Taiyuan University of Technology, Ministry of Education and Shanxi Province, No. 79 Yingze West Street, Taiyuan 030024 (China); Kandiyoti, R. [Department of Chemical Engineering and Chemical Technology, Imperial College, University of London, London SW7 2BY (United Kingdom)

2004-10-15

Point of Ayr coal has been extracted using three solvents, tetralin, quinoline and 1-methyl-2-pyrrolidinone (NMP) at two temperatures 350 and 450 C, corresponding approximately to before and after the onset of massive covalent bond scission by pyrolysis. The three solvents differ in solvent power and the ability to donate hydrogen atoms to stabilise free radicals produced by pyrolysis of the coal. The extracts were prepared in a flowing solvent reactor to minimise secondary thermal degradation of the primary extracts. Analysis of the pentane-insoluble fractions of the extracts was achieved by size exclusion chromatography, UV-fluorescence spectroscopy in NMP solvent and probe mass. With increasing extraction temperature, the ratio of the amount having big molecular weight to that having small molecular weight in tetralin extracts was increased; the tetralin extract yield increased from 12.8% to 75.9%; in quinoline, increasing extraction temperature did not have an effect on the molecular weight of products but there was a big increase in extract yield. The extracts in NMP showed the enhanced solvent extraction power at both temperatures, with a shift in the ratio of larger molecules to smaller molecules with increasing extraction temperature and with the highest conversion of Point of Ayr coal among these three solvents at both temperatures. Solvent adducts were detected in the tetralin and quinoline extracts by probe mass spectrometry; solvent products were formed from NMP at both temperatures.

Use of tobacco seed oil methyl ester in a turbocharged indirect injection diesel engine

International Nuclear Information System (INIS)

Usta, N.

2005-01-01

Vegetable oils and their methyl/ethyl esters are alternative renewable fuels for compression ignition engines. Different kinds of vegetable oils and their methyl/ethyl esters have been tested in diesel engines. However, tobacco seed oil and tobacco seed oil methyl ester have not been tested in diesel engines, yet. Tobacco seed oil is a non-edible vegetable oil and a by-product of tobacco leaves production. To the author's best knowledge, this is the first study on tobacco seed oil methyl ester as a fuel in diesel engines. In this study, potential tobacco seed production throughout the world, the oil extraction process from tobacco seed and the transesterification process for biodiesel production were examined. The produced tobacco seed oil methyl ester was characterized by exposing its major properties. The effects of tobacco seed oil methyl ester addition to diesel No. 2 on the performance and emissions of a four cycle, four cylinder turbocharged indirect injection (IDI) diesel engine were examined at both full and partial loads. Experimental results showed that tobacco seed oil methyl ester can be partially substituted for the diesel fuel at most operating conditions in terms of performance parameters and emissions without any engine modification and preheating of the blends. (Author)

Stabilization of Empty Fruit Bunch derived Bio-oil using Solvents

Directory of Open Access Journals (Sweden)

Chung Loong Yiin

2016-03-01

Full Text Available The intention of this research was to select the ideal condition for accelerated aging of bio-oil and the consequences of additive in stabilizing the bio-oil. The bio-oil was produced from the catalytic pyrolysis of empty fruit bunch. The optimum reaction conditions applied to obtain the utmost bio-oil yield were 5 wt% of H-Y catalyst at reaction temperature of 500 °C and nitrogen flow rate of 100 ml/min. A 10 wt% of solvents including acetone, ethanol, and ethyl acetate were used to study the bio-oil’s stability. All the test samples were subjected to accelerated aging at temperature of 80 oC for 7 days. The properties of samples used as the indicator of aging were viscosity and water content. The effectiveness of solvents increased in the following order: acetone, ethyl acetate, and 95 vol% ethanol. Based on the result of Gas chromatography-mass spectrometry (GC-MS, it could impede the chain of polymerization by converting the active units in the oligomer chain to inactive units. The solvent reacted to form low molecular weight products which resulted in lower viscosity and lessen the water content in bio-oil. Addition of 95 vol% ethanol also inhibited phase separation.

Fast and efficient method for reduction of carbonyl compounds with NaBH{sub 4} /wet SiO{sub 2} under solvent free condition

Energy Technology Data Exchange (ETDEWEB)

Zeynizadeh, Behzad; Bahyar, Tarifeh [Urmia University, Urmia (Iran, Islamic Republic of). Faculty of Sciences. Dept. of Chemistry]. E-mail: b.zeynizadeh@mail.urmia.ac.ir

2005-11-15

Reduction of structurally different carbonyl compounds such as aldehydes, ketones, {alpha},{beta}-unsaturated enals and enones, {alpha}-diketones and acyloins were accomplished efficiently by sodium borohydride in the presence of wet SiO{sub 2} (30% m/m) under solvent free condition. The reactions were performed at room tempere or 75-80 deg C with high to excellent yields of the corresponding products. The chemoselective reduction of aldehydes over ketones was achieved successfully with this reducing system. (author)

The use of deuterated ethyl acetate in highly concentrated electrolyte as a low-cost solvent for in situ neutron diffraction measurements of Li-ion battery electrodes

International Nuclear Information System (INIS)

Petibon, R.; Li, Jing; Sharma, Neeraj; Pang, Wei Kong; Peterson, Vanessa K.; Dahn, J.R.

2015-01-01

A low-cost deuterated electrolyte suitable for in situ neutron diffraction measurements of normal and high voltage Li-ion battery electrodes is reported here. Li[Ni 0.4 Mn 0.4 Co 0.2 ]O 2 /graphite (NMC(442)/graphite) pouch cells filled with 1:0.1:2 (molar ratio) of lithium bis(fluorosulfonyl) imide (LiFSi):LiPF 6 : ethyl acetate (EA) and LiFSi:LiPF 6 :deuterated EA (d8-EA) electrolytes were successfully cycled between 2.8 V and 4.7 V at 40°C for 250 h without significant capacity loss, polarization growth, or gas production. The signal-to-noise ratio of neutron powder diffraction patterns taken on NMC(442) powder with a conventional deuterated organic carbonate-based electrolyte and filled with LiFSi:LiPF 6 :d8-EA electrolyte were virtually identical. Out of all the solvents widely available in deuterated form tested in highly-concentrated systems, EA was the only one providing a good balance between cost and charge-discharge capacity retention to 4.7 V. The use of such an electrolyte blend would half the cost of deuterated solvents needed for in situ neutron diffraction measurements of Li-ion batteries compared to conventional deuterated carbonate-based electrolytes

Thermodynamic models for determination of the solubility of omeprazole in pure and mixture organic solvents from T = (278.15 to 333.15) K

International Nuclear Information System (INIS)

Hu, Yonghong; Wu, Gang; Gu, Pengfei; Yang, Wenge; Wang, Chunxiao; Ding, Zhiwen; Cao, Yang

2016-01-01

Highlights: • The solubility increased with increasing temperature. • The data were fitted using the modified Apelblat equation and other models. • The Gibbs energy, enthalpy and entropy were calculated by the van’t Hoff analysis. - Abstract: Data on corresponding (solid + liquid) equilibrium of omeprazole in different solvents are essential for a preliminary study of industrial applications. In this paper, the (solid + liquid) equilibrium of omeprazole in water, methanol, ethanol, 1-butanol, acetonitrile, acetone, ethyl acetate, tetrahydrofuran pure solvents and (tetrahydrofuran + ethyl acetate) mixture solvents were explored within the temperatures from 278.15 K to 333.15 K under atmosphere pressure. For the temperature range investigated, the solubility of omeprazole in the solvents increased with increasing temperature. From (278.15 to 333.15) K, the solubility of omeprazole in tetrahydrofuran is superior to other selected pure solvents. The modified Apelblat model, the Buchowski–Ksiazaczak λh model, and the ideal model were adopted to describe and predict the change tendency of solubility. Computational results showed that the modified Apelblat model has advantages than the other two models. Numerical values of the solubility were fitted using a modified Apelblat equation, a variant of the combined nearly ideal binary solvent/Redich–Kister (CNIBS/R–K) model and Jouyban–Acree model in (tetrahydrofuran + ethyl acetate) binary solvent mixture. Computational results showed that the CNIBS/R–K model is superior to the other equations. In addition, the calculated thermodynamic parameters indicate that in each solvent studied the dissolution of omeprazole is endothermic, non-spontaneous and is an entropy-driven process.

In vitro Antioxidant and Antiproliferative Activities of Various Solvent Fractions from Clerodendrum viscosum Leaves.

Science.gov (United States)

Shendge, Anil Khushalrao; Basu, Tapasree; Chaudhuri, Dipankar; Panja, Sourav; Mandal, Nripendranath

2017-07-01

Free radicals such as reactive oxygen and nitrogen species, generated in the body, play an important role in the fulfillment of various physiological functions but their imbalance in the body lead to cellular injury and various clinical disorders such as cancer, neurodegenaration, and inflammation. The objective of this study is to fight this problem, natural antioxidant from plants can be considered as possible protective agents against various diseases such as cancer which might also modify the redox microenvironment to reduce the genetic instability. This study was designed to evaluate the antioxidant and antiproliferative potential of Clerodendrum viscosum fractions against various carcinomas. In this present study, 70% methanolic extract of C. viscosum leaves have been fractionated to obtain hexane, chloroform, ethyl acetate, butanol, and water fractions, which were tested for their antioxidant and anticancer properties. It was observed that chloroform and ethyl acetate fractions showed good free radical scavenging properties as well as inhibited the proliferation of human lung cancer (A459), breast (MCF-7), and brain (U87) cells. Moreover, they arrested the cell cycle at G2/M phase of breast and brain cancer. These inhibitory effects were further confirmed by bromodeoxyuridine uptake imaging. Phytochemical investigations further indicate the presence of tannic acid, quercetin, ellagic caid, gallic acid, reserpine, and methyl gallate which might be the reason for these fractions' antioxidant and antiproliferative activities. Clerodendrum viscosum leaf chloroform and Clerodendrum viscosum leaf ethyl acetate fractions from C. viscosum showed good reactive oxygen species and reactive nitrogen species scavenging potential. Both the fractions arrested cell cycle at G2/M phase in MCF-7 and U87 cells which lead to induce apoptosis. Crude extract of Clerodendrum viscosum leaves was fractionated using different solventsAmong them, chloroform and ethyl acetate fractions

Biomonitoring of N-ethyl-2-pyrrolidone in automobile varnishers.

Science.gov (United States)

Koslitz, Stephan; Meier, Swetlana; Schindler, Birgit Karin; Weiss, Tobias; Koch, Holger Martin; Brüning, Thomas; Käfferlein, Heiko Udo

2014-12-01

N-alkyl-2-pyrrolidones are important organic solvents for varnishes in industry. This study investigates exposure to N-ethyl-2-pyrrolidone (NEP) in varnishing of hard plastic components in an automobile plant. Two specific biomarkers of exposure, 5-hydroxy-N-ethyl-2-pyrrolidone (5-HNEP) and 2-hydroxy-N-ethylsuccinimide (2-HESI), were analyzed in urine samples of 14 workers. For this purpose, pre-shift, post-shift and next day pre-shift urine samples were collected midweek. Twelve workers performed regular work tasks (loading, wiping and packing), whereas two workers performed special work tasks including cleaning the sprayer system with organic solvents containing N-alkyl-2-pyrrolidones. Spot urine samples of nine non-exposed persons of the same plant served as controls. Median post-shift urinary levels of workers with regular work tasks (5-HNEP: 0.15 mg/L; 2-HESI: 0.19 mg/L) were ∼5-fold higher compared to the controls (0.03 mg/L each). Continuously increasing metabolite levels, from pre-shift via post-shift to pre-shift samples of the following day, were observed in particular for the two workers with the special working tasks. Maximum levels were 31.01 mg/L (5-HNEP) and 8.45 mg/L (2-HESI). No clear trend was evident for workers with regular working tasks. In summary, we were able to show that workers can be exposed to NEP during varnishing tasks in the automobile industry. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

9-Ethyl-2,3-dihydro-9H-carbazol-4(1H-one

Directory of Open Access Journals (Sweden)

S. Sriman Narayanan

2008-09-01

Full Text Available In the title compound, C28H30N2O2, the cyclohexene ring system adopts a sofa conformation. The crystal structure is stabilized by C—H...O interactions between methyl H atoms of the ethyl substituents and the O atoms of carbonyl groups of adjacent molecules, and by an intermolecular carbonyl–carbonyl interactions [3.207 (2 Å

Untitled

Indian Academy of Sciences (India)

-aminobenzene-camphor:#"P”. AM SAAAAASA SAASAASSMMSSSLgAAA AAAA AAAASASASS. 一口. Solvent Water Methyl alcohol Ethyl alcohol } Pyridine. Concentration ( d- 1-0000 1.0000 1.0000 in gms./100 c.c. i - I • 0000 | 1 .0000 1.0000 ...

Advanced heat pump for the recovery of volatile organic compounds. Phase 1, Conceptual design of an advanced Brayton cycle heat pump for the recovery of volatile organic compounds: Final report

Energy Technology Data Exchange (ETDEWEB)

1992-03-01

Emissions of Volatile Organic Compounds (VOC) from stationary industrial and commercial sources represent a substantial portion of the total US VOC emissions. The ``Toxic-Release Inventory`` of The US Environmental Protection Agency estimates this to be at about 3 billion pounds per year (1987 estimates). The majority of these VOC emissions are from coating processes, cleaning processes, polymer production, fuel production and distribution, foam blowing,refrigerant production, and wood products production. The US Department of Energy`s (DOE) interest in the recovery of VOC stems from the energy embodied in the recovered solvents and the energy required to dispose of them in an environmentally acceptable manner. This Phase I report documents 3M`s work in close working relationship with its subcontractor Nuclear Consulting Services (Nucon) for the preliminary conceptual design of an advanced Brayton cycle heat pump for the recovery of VOC. Nucon designed Brayton cycle heat pump for the recovery of methyl ethyl ketone and toluene from coating operations at 3M Weatherford, OK, was used as a base line for the work under cooperative agreement between 3M and ODE. See appendix A and reference (4) by Kovach of Nucon. This cooperative agreement report evaluates and compares an advanced Brayton cycle heat pump for solvent recovery with other competing technologies for solvent recovery and reuse. This advanced Brayton cycle heat pump is simple (very few components), highly reliable (off the shelf components), energy efficient and economically priced.

Advanced heat pump for the recovery of volatile organic compounds

Energy Technology Data Exchange (ETDEWEB)

1992-03-01

Emissions of Volatile Organic Compounds (VOC) from stationary industrial and commercial sources represent a substantial portion of the total US VOC emissions. The Toxic-Release Inventory'' of The US Environmental Protection Agency estimates this to be at about 3 billion pounds per year (1987 estimates). The majority of these VOC emissions are from coating processes, cleaning processes, polymer production, fuel production and distribution, foam blowing,refrigerant production, and wood products production. The US Department of Energy's (DOE) interest in the recovery of VOC stems from the energy embodied in the recovered solvents and the energy required to dispose of them in an environmentally acceptable manner. This Phase I report documents 3M's work in close working relationship with its subcontractor Nuclear Consulting Services (Nucon) for the preliminary conceptual design of an advanced Brayton cycle heat pump for the recovery of VOC. Nucon designed Brayton cycle heat pump for the recovery of methyl ethyl ketone and toluene from coating operations at 3M Weatherford, OK, was used as a base line for the work under cooperative agreement between 3M and ODE. See appendix A and reference (4) by Kovach of Nucon. This cooperative agreement report evaluates and compares an advanced Brayton cycle heat pump for solvent recovery with other competing technologies for solvent recovery and reuse. This advanced Brayton cycle heat pump is simple (very few components), highly reliable (off the shelf components), energy efficient and economically priced.

Dissolution of South African Eucalyptus sawdust wood in [Emim][OAc]/Co-solvent mixtures

CSIR Research Space (South Africa)

Tywabi, Zikhona

2017-03-01

Full Text Available The paper presents a method of obtaining wood cellulose by dissolution of eucalyptus sawdust in a mixture of ionic liquid (IL) 1-ethyl-3-methylimidazolium acetate [Emim][OAc] together with co-solvents; dimethylformamide (DMF) and dimethylsulphoxide...

Natural sparkling guava wine: volatile and physicochemical characterization

Directory of Open Access Journals (Sweden)

Silvana Maria Michelin Bertagnolli

Full Text Available ABSTRACT: Although different tropical fruit species have been used in the development of fermented beverages, there are only few references in the literature to the production of natural sparkling wines from fruits other than grapes. In this sense, the objective of the present research was the development and physicochemical and volatile characterization of a natural sparkling guava wine produced by the champenoise method. Volatile compounds were identified by gas chromatography coupled to mass spectrometry using the headspace solid-phase microextraction (HS-SPME technique on samples. Eighty-nine volatile compounds were detected, of which 51 were identified. Esters were the predominant class of volatile compounds (a total of 26, followed by alcohols (10, terpenes (9, ketones (3, and acids (3. Volatile compounds with possible odoriferous activity were reported in the beverage, including ethyl octanoate, ethyl 5-hexenoate, phenethyl acetate, (E-β-damascenone, (E-ethyl cinnamate, 2-methyl butyl acetate, 3-methylbutanol, ethyl 3-(E-hexenoate, and methyl 5-hexenoate. Natural sparkling guava wine produced showed a complex composition of fruity and floral aromas. Furthermore, the use of the champenoise method, traditionally applied to grapes, enabled the manufacture of a natural sparkling guava wine with physicochemical characteristics equivalent to those of sparkling wines made from grapes.

Analysis of recovered solvents from coal liquefaction in a flowing-solvent reactor by SEC and UV-fluorescence

Energy Technology Data Exchange (ETDEWEB)

Li, W.Y.; Feng, J.; Xie, K.C.; Kandiyoti, R. [Taiyuan University of Technology, Taiyuan (China)

2005-08-01

Point of Ayr coal has been extracted using three solvents: tetralin, quinoline and 1-methyl-2-pyrrolidinone (NMP); at two temperatures: 350 {sup o}C and 450{sup o}C, corresponding approximately to before and after the onset of massive covalent bond scission by pyrolysis. These solvents differ in solvent power and the ability to donate hydrogen atoms to stabilize free radicals produced by pyrolysis of the coal. Analysis of the fresh solvents and recovered solvents from coal liquefaction was achieved by size exclusion chromatography and UV-fluorescence spectroscopy. In the blank run, it was testified that the filling material sand and the steel powder did not react with solvent with increasing reaction temperature. The role of hydrogen donation in the tetralin extracts was to increase the proportion of large molecules with increasing extraction temperature. Quinoline and NMP both have the powerful extracting capability to get more materials out of coal with increasing extraction temperature.

Analysis of recovered solvents from coal liquefaction in a flowing-solvent reactor by SEC and UV-fluorescence

Energy Technology Data Exchange (ETDEWEB)

Wen-Ying Li; Jie Feng; Ke-Chang Xie; R. Kandiyoti [Taiyuan University of Technology, Taiyuan (China). Key Laboratory of Coal Science and Technology for Ministry of Education and Shanxi Province

2005-08-01

Point of Ayr coal has been extracted using three solvents: tetralin, quinoline and 1-methyl-2-pyrrolidinone (NMP); at two temperatures: 350{sup o}C and 450{sup o}C, corresponding approximately to before and after the onset of massive covalent bond scission by pyrolysis. These solvents differ in solvent power and the ability to donate hydrogen atoms to stabilize free radicals produced by pyrolysis of the coal. Analysis of the fresh solvents and recovered solvents from coal liquefaction was achieved by size exclusion chromatography and UV-fluorescence spectroscopy. In the blank run, it was testified that the filling material sand and the steel powder did not react with solvent with increasing reaction temperature. The role of hydrogen donation in the tetralin extracts was to increase the proportion of large molecules with increasing extraction temperature. Quinoline and NMP both have the powerful extracting capability to get more materials out of coal with increasing extraction temperature.

Dual-isotope technique for determination of in vivo ketone body kinetics

International Nuclear Information System (INIS)

Miles, J.M.; Schwenk, W.F.; McClean, K.L.; Haymond, M.W.

1986-01-01

Total ketone body specific activity has been widely used in studies of ketone body metabolism to circumvent so-called isotope disequilibrium between the two major ketone body pools, acetoacetate and beta-hydroxybutyrate. Recently, this approach has been criticized on theoretical grounds. In the present studies, [13C]acetoacetate and beta-[14C]hydroxybutyrate were simultaneously infused in nine mongrel dogs before and during an infusion of either unlabeled sodium acetoacetate or unlabeled sodium beta-hydroxybutyrate. Ketone body turnover was determined using total ketone body specific activity, total ketone body moles % enrichment, and an open two-pool model, both before and during the exogenous infusion of unlabeled ketone bodies. Basal ketone body turnover rates were significantly higher using [13C]acetoacetate than with either beta-[14C]hydroxybutyrate alone or the dual-isotope model (3.6 +/- 0.5 vs. 2.2 +/- 0.2 and 2.7 +/- 0.2 mumol X kg-1 X min-1, respectively, P less than 0.05). During exogenous infusion of unlabeled sodium acetoacetate, the dual-isotope model provided the best estimate of ketone body inflow, whereas 14C specific activity underestimated the known rate of acetoacetate infusion by 55% (P less than 0.02). During sodium beta-hydroxybutyrate infusion, [13C]-acetoacetate overestimated ketone body inflow by 55% (P = NS), while better results were obtained with 14C beta-hydroxybutyrate alone and the two-pool model. Ketone body interconversion as estimated by the dual-isotope technique increased markedly during exogenous ketone body infusion. In conclusion, significant errors in estimation of ketone body inflow were made using single-isotope techniques, whereas a dual-isotope model provided reasonably accurate estimates of ketone body inflow during infusion of exogenous acetoacetate and beta-hydroxybutyrate

Karakteristik Sifat Tarik Dan Mode Patahan Komposit Polyester Berpenguat Serat Tapis Kelapa

OpenAIRE

Astika, I Made; Dwijana, I Gusti Komang

2014-01-01

The purpose of this study is to investigate the mechanical properties i.e. tensile strength of composites coconut filter fiber. In the future this material can be used to replace the wood, bamboo and gipsun which are high price and lower water resistance. The research material made with coconut filter fiber as reinforcement and matrix resin unsaturated polyester (UPRs) type Yukalac BQTN 157, with 1% hardener types MEKPO (Methyl Ethyl Ketone Peroxide) and fiber treatment by  0.5% KMnO4...

Carbonyl Activation by Borane Lewis Acid Complexation: Transition States of H2 Splitting at the Activated Carbonyl Carbon Atom in a Lewis Basic Solvent and the Proton-Transfer Dynamics of the Boroalkoxide Intermediate.

Science.gov (United States)

Heshmat, Mojgan; Privalov, Timofei

2017-07-06

By using transition-state (TS) calculations, we examined how Lewis acid (LA) complexation activates carbonyl compounds in the context of hydrogenation of carbonyl compounds by H 2 in Lewis basic (ethereal) solvents containing borane LAs of the type (C 6 F 5 ) 3 B. According to our calculations, LA complexation does not activate a ketone sufficiently enough for the direct addition of H 2 to the O=C unsaturated bond; but, calculations indicate a possibly facile heterolytic cleavage of H 2 at the activated and thus sufficiently Lewis acidic carbonyl carbon atom with the assistance of the Lewis basic solvent (i.e., 1,4-dioxane or THF). For the solvent-assisted H 2 splitting at the carbonyl carbon atom of (C 6 F 5 ) 3 B adducts with different ketones, a number of TSs are computed and the obtained results are related to insights from experiment. By using the Born-Oppenheimer molecular dynamics with the DFT for electronic structure calculations, the evolution of the (C 6 F 5 ) 3 B-alkoxide ionic intermediate and the proton transfer to the alkoxide oxygen atom were investigated. The results indicate a plausible hydrogenation mechanism with a LA, that is, (C 6 F 5 ) 3 B, as a catalyst, namely, 1) the step of H 2 cleavage that involves a Lewis basic solvent molecule plus the carbonyl carbon atom of thermodynamically stable and experimentally identifiable (C 6 F 5 ) 3 B-ketone adducts in which (C 6 F 5 ) 3 B is the "Lewis acid promoter", 2) the transfer of the solvent-bound proton to the oxygen atom of the (C 6 F 5 ) 3 B-alkoxide intermediate giving the (C 6 F 5 ) 3 B-alcohol adduct, and 3) the S N 2-style displacement of the alcohol by a ketone or a Lewis basic solvent molecule. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of electrostatic interaction on thermochemical behavior of 12-crown-4 ether in various polar solvents

International Nuclear Information System (INIS)

Barannikov, Vladimir P.; Guseynov, Sabir S.; Vyugin, Anatoliy I.

2010-01-01

The enthalpies of solution of 12-crown-4 ether have been measured in chloroform, ethyl acetate, acetone, pyridine, acetonitrile and methanol at 298.15 K. The values of enthalpy of solvation and solute-solvent interaction were determined from the obtained results and similar literature data for 12-crown-4 in solvents of various polarities. It was shown that the certain correlation is observed between the enthalpy of solute-solvent interaction and the squared dipole moment of the solvent molecules for solutions in tetrachlormethane, ethyl acetate, pyridine, acetonitrile, DMF, DMSO and propylene carbonate. This means that the electrostatic interaction of 12-crown-4 with polar solvent molecules contributes significantly to the exothermic effect of solvation. The understated negative value was found for the enthalpy of interaction of 12-crown-4 with acetone that can be connected with domination of low polar conformer of the crown ether in acetone medium. The most negative values of enthalpy of solvation are observed for solutions in chloroform and water because of hydrogen bonding between O-atoms of crown ether and molecules of the indicated solvents. This effect is not observed for methanol. The negative coefficient of pairwise solute-solute interaction in methanol indicates that the effects of solvophobic solute-solute interaction and H-bonding of the ether molecule with chain associates of methanol are not evinced in the thermochemical behavior of 12-crown-4.

Successful topical dissolution of cholesterol gallbladder stones using ethyl propionate.

Science.gov (United States)

Hofmann, A F; Amelsberg, A; Esch, O; Schteingart, C D; Lyche, K; Jinich, H; Vansonnenberg, E; D'Agostino, H B

1997-06-01

Topical dissolution of cholesterol gallbladder stones using methyl tert-butyl ether (MTBE) is useful in symptomatic patients judged too ill for surgery. Previous studies showed that ethyl propionate (EP), a C5 ester, dissolves cholesterol gallstones rapidly in vitro, but differs from MTBE in being eliminated so rapidly by the liver that blood levels remain undetectable. Our aim was to test EP as a topical dissolution agent for cholesterol gallbladder stones. Five high-risk patients underwent topical dissolution of gallbladder stones by EP. In three patients, the solvent was instilled via a cholecystostomy tube placed previously to treat acute cholecystitis; in two patients, a percutaneous transhepatic catheter was placed in the gallbladder electively. Gallstone dissolution was assessed by chromatography, by gravimetry, and by catheter cholecystography. Total dissolution of gallstones was obtained in four patients after 6-10 hr of lavage; in the fifth patient, partial gallstone dissolution facilitated basketing of the stones. In two patients, cholesterol dissolution was measured and averaged 30 mg/min. Side effects were limited to one episode of transient hypotension and pain at the infusion site; no patient developed somnolence or nausea. Gallstone elimination was associated with relief of symptoms. EP is an acceptable alternative to MTBE for topical dissolution of cholesterol gallbladder stones in high-risk patients. The lower volatility and rapid hepatic extraction of EP suggest that it may be preferable to MTBE in this investigational procedure.

Stimulation of {sup 125}I-3-iodo-{alpha}-methyl-L-tyrosine uptake in Chinese hamster ovary (CHO-K1) cells by tyrosine esters

Energy Technology Data Exchange (ETDEWEB)

Shikano, Naoto [Department of Radiological Sciences, Center for Medical Sciences and Center for Humanities and Sciences, Ibaraki Prefectural University of Health Sciences, Inashiki-gun, Ibaraki (Japan)], E-mail: sikano@ipu.ac.jp; Ogura, Masato; Sagara, Jun-ichi; Nakajima, Syuichi [Department of Radiological Sciences, Center for Medical Sciences and Center for Humanities and Sciences, Ibaraki Prefectural University of Health Sciences, Inashiki-gun, Ibaraki (Japan); Kobayashi, Masato [Division of Health Science, Graduate School of Health Sciences, Kanazawa University, Kanazawa, Ishikawa (Japan); Baba, Takeshi; Yamaguchi, Naoto; Iwamura, Yukio; Kubota, Nobuo [Department of Radiological Sciences, Center for Medical Sciences and Center for Humanities and Sciences, Ibaraki Prefectural University of Health Sciences, Inashiki-gun, Ibaraki (Japan); Kawai, Keiichi [Division of Health Science, Graduate School of Health Sciences, Kanazawa University, Kanazawa, Ishikawa (Japan)

2010-02-15

Introduction: Transport of the amino acid analog {sup 123}I-3-iodo-{alpha}-methyl-L-tyrosine, which is used in clinical SPECT imaging, occurs mainly via L-type amino acid transporter type 1 (LAT1; an amino acid exchanger). As LAT1 is highly expressed in actively proliferating tumors, we made a preliminary investigation of the effects of amino acid esters on enhancement of {sup 125}I-3-iodo-{alpha}-methyl-L-tyrosine (IMT) uptake via LAT1 in Chinese hamster ovary (CHO-K1) cells. Methods: Because the sequence of the CHO-K1 LAT1 gene is not available, we confirmed LAT1 expression through IMT (18.5 kBq) uptake mechanisms using specific inhibitors. L-Gly, L-Ser, L-Leu, L-Phe, L-Met, L-Tyr, D-Tyr, L-Val and L-Lys ethyl/methyl esters were tested in combination with IMT. Time-course studies over a 3-h period were conducted, and the concentration dependence of L-Tyr ethyl and methyl esters (0.001 to 10 mM) in combination with IMT was also examined. For a proof of de-esterification of L- and D-Tyr ethyl and methyl esters in the cells (by enzymatic attack or other cause), the concentration of L- and D-Tyr was analyzed by high-performance liquid chromatography of the esters in phosphate buffer (pH 7.4) and cell homogenates at 37 deg. C or under ice-cold conditions. Results: Inhibition tests suggested that LAT1 is involved in IMT uptake by CHO-K1 cells. Co-administration of 1 mM of L-Tyr ethyl or methyl ester with IMT produced the greatest enhancement. The de-esterification reaction was stereo selective and temperature dependent in the homogenate. De-esterification kinetics were very fast in the homogenate and very slow in the phosphate buffer. Conclusions: The L-Tyr ethyl or methyl esters were the most effective enhancers of IMT uptake into CHO-K1 cells and acted by trans-stimulation of the amino acid exchange function of LAT1. This result suggests that de-esterification in the cells may be caused by enzymatic attack. We will use IMT and L-Tyr ethyl or methyl esters to examine

Natrolite zeolite: A natural and reusable catalyst for one-pot synthesis of α-aminophosphonates under solvent-free conditions

Directory of Open Access Journals (Sweden)

Siavash Bahari

2017-02-01

Full Text Available α-Aminophosphonates are synthesized efficiently by one-pot reaction of aldehydes or ketones, amines, trialkyl phosphites in the presence of Natrolite zeolite as a natural catalyst under solvent-free conditions. Furthermore, the catalyst can be reused several times without any significant loss of catalytic activity.

Systematic investigations on acyclic organic carbonate solvents for lithium-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Vetter, J.; Peter, S.; Novak, P.

2003-03-01

Electrochemical cycling tests on cells with graphite electrodes and several alkyl methyl carbonates were performed. Experiments with mixed binary solvent electrolytes with ethylene carbonate (EC) showed that the alkyl methyl carbonates H{sub 3}CO(CO)O(CH{sub 2}){sub n}H (n = 3-5) are suitable as co-solvents in lithium-ion batteries. Ternary mixtures of EC, BMC, and propylene carbonate (PC) showed better overall performances than EC/PC electrolytes. The branched isobutyl methyl carbonate (i-BMC) outperforms its linear isomer (BMC) in terms of electrochemical performance. LiPF{sub 6} is superior to LiClO{sub 4} as conducting salt in both EC/BMC and EC/i-BMC mixtures in terms of electrolyte conductivity, rate capability, and cycling stability. (author)

Two Players Make a Formidable Combination: In Situ Generated Poly(acrylic anhydride-2-methyl-acrylic acid-2-oxirane-ethyl ester-methyl methacrylate) Cross-Linking Gel Polymer Electrolyte toward 5 V High-Voltage Batteries.

Science.gov (United States)

Ma, Yue; Ma, Jun; Chai, Jingchao; Liu, Zhihong; Ding, Guoliang; Xu, Gaojie; Liu, Haisheng; Chen, Bingbing; Zhou, Xinhong; Cui, Guanglei; Chen, Liquan

2017-11-29

Electrochemical performance of high-voltage lithium batteries with high energy density is limited because of the electrolyte instability and the electrode/electrolyte interfacial reactivity. Hence, a cross-linking polymer network of poly(acrylic anhydride-2-methyl-acrylic acid-2-oxirane-ethyl ester-methyl methacrylate) (PAMM)-based electrolyte was introduced via in situ polymerization inspired by "shuangjian hebi", which is a statement in a traditional Chinese Kungfu story similar to the synergetic effect of 1 + 1 > 2. A poly(acrylic anhydride) and poly(methyl methacrylate)-based system is very promising as electrolyte materials for lithium-ion batteries, in which the anhydride and acrylate groups can provide high voltage resistance and fast ionic conductivity, respectively. As a result, the cross-linking PAMM-based electrolyte possesses a significant comprehensive enhancement, including electrochemical stability window exceeding 5 V vs Li + /Li, an ionic conductivity of 6.79 × 10 -4 S cm -1 at room temperature, high mechanical strength (27.5 MPa), good flame resistance, and excellent interface compatibility with Li metal. It is also demonstrated that this gel polymer electrolyte suppresses the negative effect resulting from dissolution of Mn 2+ ions at 25 and 55 °C. Thus, the LiNi 0.5 Mn 1.5 O 4 /Li and LiNi 0.5 Mn 1.5 O 4 /Li 4 Ti 5 O 12 cells using the optimized in situ polymerized cross-linking PAMM-based gel polymer electrolyte deliver stable charging/discharging profiles and excellent rate performance at room temperature and even at 55 °C. These findings suggest that the cross-linking PAMM is an intriguing candidate for 5 V class high-voltage gel polymer electrolyte toward high-energy lithium-on batteries.

Chemical approach to solvent removal during nanoencapsulation: its application to preparation of PLGA nanoparticles with non-halogenated solvent

Energy Technology Data Exchange (ETDEWEB)

Lee, Youngme [Ewha Womans University, College of Pharmacy (Korea, Republic of); Sah, Eric [University of Notre Dame, College of Science (United States); Sah, Hongkee, E-mail: hsah@ewha.ac.kr [Ewha Womans University, College of Pharmacy (Korea, Republic of)

2015-11-15

The objective of this study was to develop a new oil-in-water emulsion-based nanoencapsulation method for the preparation of PLGA nanoparticles using a non-halogenated solvent. PLGA (60–150 mg) was dissolved in 3 ml of methyl propionate, which was vortexed with 4 ml of a 0.5–4 % polyvinyl alcohol solution. This premix was sonicated for 2 min, added into 30 ml of the aqueous polyvinyl alcohol solution, and reacted with 3 ml of 10 N NaOH. Solvent removal was achieved by the alkaline hydrolysis of methyl propionate dissolved in an aqueous phase into water-soluble methanol and sodium propionate. It was a simple but effective technique to quickly harden nanoemulsion droplets into nanoparticles. The appearing PLGA nanoparticles were recovered by ultracentrifugation and/or dialysis, lyophilized with trehalose, and redispersed by water. This nanoencapsulation technique permitted a control of their mean diameters over 151.7 ± 3.8 to 440.2 ± 22.2 nm at mild processing conditions. When the aqueous polyvinyl alcohol concentration was set at ≥1 %, nanoparticles showed uniform distributions with polydispersity indices below 0.1. There were no significant changes in their mean diameters and size distribution patterns before and after lyophilization. When mestranol was encapsulated into nanoparticles, the drug was completely nanoencapsulated: depending on experimental conditions, their encapsulation efficiencies were determined to be 99.4 ± 7.2 to 105.8 ± 6.3 %. This simple, facile nanoencapsulation technique might have versatile applications for the preparation of polymeric nanoparticulate dosage forms.Graphical AbstractSchematic illustration of an innovative chemical approach to solvent removal during nanoencapsulation. Methyl propionate present in the aqueous continuous phase reacts with sodium hydroxide, thereby producing methanol and sodium propionate. Its alkaline hydrolysis allows the continuous extraction of the solvent out of nanoemulsion

Chemical approach to solvent removal during nanoencapsulation: its application to preparation of PLGA nanoparticles with non-halogenated solvent

International Nuclear Information System (INIS)

Lee, Youngme; Sah, Eric; Sah, Hongkee

2015-01-01

The objective of this study was to develop a new oil-in-water emulsion-based nanoencapsulation method for the preparation of PLGA nanoparticles using a non-halogenated solvent. PLGA (60–150 mg) was dissolved in 3 ml of methyl propionate, which was vortexed with 4 ml of a 0.5–4 % polyvinyl alcohol solution. This premix was sonicated for 2 min, added into 30 ml of the aqueous polyvinyl alcohol solution, and reacted with 3 ml of 10 N NaOH. Solvent removal was achieved by the alkaline hydrolysis of methyl propionate dissolved in an aqueous phase into water-soluble methanol and sodium propionate. It was a simple but effective technique to quickly harden nanoemulsion droplets into nanoparticles. The appearing PLGA nanoparticles were recovered by ultracentrifugation and/or dialysis, lyophilized with trehalose, and redispersed by water. This nanoencapsulation technique permitted a control of their mean diameters over 151.7 ± 3.8 to 440.2 ± 22.2 nm at mild processing conditions. When the aqueous polyvinyl alcohol concentration was set at ≥1 %, nanoparticles showed uniform distributions with polydispersity indices below 0.1. There were no significant changes in their mean diameters and size distribution patterns before and after lyophilization. When mestranol was encapsulated into nanoparticles, the drug was completely nanoencapsulated: depending on experimental conditions, their encapsulation efficiencies were determined to be 99.4 ± 7.2 to 105.8 ± 6.3 %. This simple, facile nanoencapsulation technique might have versatile applications for the preparation of polymeric nanoparticulate dosage forms.Graphical AbstractSchematic illustration of an innovative chemical approach to solvent removal during nanoencapsulation. Methyl propionate present in the aqueous continuous phase reacts with sodium hydroxide, thereby producing methanol and sodium propionate. Its alkaline hydrolysis allows the continuous extraction of the solvent out of nanoemulsion

[Chemical Constituents from Ethyl Acetate Extract of Psidium guajava Leaves (II)].

Science.gov (United States)

Ouyang, Wen; Zhu, Xiao-ai; He, Cui-xia; Chen, Xue-xiang; Ye, Shu-min; Peng, Shan; Cao, Yong

2015-08-01

To study the chemical constituents from ethyl acetate extract of Psidium guajava leaves. The constituents were separated and purified by silica gel and Sephadex LH-20 column chromatography and their structures were identified on the basis of physicochemical properties and spectral data. Eleven compounds were isolated and identified as 6,10,14-trimethyl-2-pentadecanone (1), phytyl-acetate (2), cubenol (3), eucalyptin (4), n-docosanoic acid-p-hydroxy-phenethylol ester (5),8-methyl-5,7- dihydroxy-flavonone (6), 6-methyl-5,7-dihydroxy-flavonone (7), betulinic acid (8), carnosol (9), quercetin (10), and 2,4,6-tirhydroxy- 3,5-dimethyl-diphenylketone-4-O-(6'"-O-galloyl)-β-D-glucoside (11). Compounds 1-9 are isolated from this plant for the first time.

Oxidative Umpolung α‐Alkylation of Ketones

DEFF Research Database (Denmark)

Shneider, O. Svetlana; Pisarevsky, Evgeni; Fristrup, Peter

2015-01-01

We disclose a hypervalent iodine mediated α-alkylative umpolung reaction of carbonyl compounds with dialkylzinc as the alkyl source. The reaction is applicable to all common classes of ketones including 1,3-dicarbonyl compounds and regular ketones via their lithium enolates. The α...

Synthesis of [14α-methyl-3H]-24,25-dihydrolanosterol

International Nuclear Information System (INIS)

DeKeczer, S.; Kertesz, D.; Parnes, H.

1993-01-01

We describe the first synthesis of isomerically pure title compound (6) at high specific activity. This required the development of a convenient, regiospecific synthesis of the δ 8(9) -15-ketone and subsequent alkylation with methyl-[ 3 H 3 ]iodide. A key step in our procedure was the use of an electrochemical reduction of the intermediate [14α-methyl- 3 H]-15-oxo-dihydrolanosterol. This process was effected cleanly and in high yield to give (6), an important assay tool in the search for cholesterol lowering agents. This approach was found to be significantly superior to the Wolff-Kishner reduction of the corresponding 3-benzoate. (Author)

Iodine - catalyzed prins cyclization of aliphatic and aromatic ketones

International Nuclear Information System (INIS)

Kishore, K.R.; Reddy, K.; Silva Junior, Luiz F.

2013-01-01

Iodine-catalyzed Prins cyclization of homoallylic alcohols and ketones was investigated. Anhydrous conditions and inert atmosphere are not required in this metal-free protocol. The reaction of 2-(3,4-dihydronaphthalene-1-yl)propan-1-ol with six aliphatic symmetric ketones gave the desired products in 67-77% yield. Cyclization was performed with four aliphatic unsymmetric ketones, leading to corresponding pyrans in 66-76% yield. Prins cyclization was also accomplished with four aromatic ketones in 37-66% yield. Finally, Prins cyclization of the monoterpene isopulegol and acetone was successfully achieved. (author)

Iodine - catalyzed prins cyclization of aliphatic and aromatic ketones

Energy Technology Data Exchange (ETDEWEB)

Kishore, K.R.; Reddy, K.; Silva Junior, Luiz F., E-mail: luizfsjr@iq.usp.br [Universidade de Sao Paulo (IQ/USP), SP (Brazil). Inst. de Quimica. Dept. de Quimica Fundamental

2013-09-15

Iodine-catalyzed Prins cyclization of homoallylic alcohols and ketones was investigated. Anhydrous conditions and inert atmosphere are not required in this metal-free protocol. The reaction of 2-(3,4-dihydronaphthalene-1-yl)propan-1-ol with six aliphatic symmetric ketones gave the desired products in 67-77% yield. Cyclization was performed with four aliphatic unsymmetric ketones, leading to corresponding pyrans in 66-76% yield. Prins cyclization was also accomplished with four aromatic ketones in 37-66% yield. Finally, Prins cyclization of the monoterpene isopulegol and acetone was successfully achieved. (author)

2-[3-Furyl(hydroxy)methyl]-2,3-dimethylcyclohexanone.

Science.gov (United States)

García, Esther; Mendoza, Virgilio; Guzmán, José Agustín; Maldonado Graniel, Luis Angel; Hernández-Ortega, Simón

2002-06-01

Contribution No. 1750 of the Instituto de Quimica, UNAM, Mexico. In the molecule of the title compound, C(13)H(18)O(3), there is a syn relationship between the two vicinal methyl groups. The six-membered ring adopts a chair conformation, with one equatorial and two axial groups, and the furyl group is almost parallel to the ketone group. Intermolecular hydrogen bonds [O[bond]H...O[double bond]C 2.814 (3) A] form chains along [100].

Extraction of pesticides in soil using supercritical carbon dioxide co-solvents

International Nuclear Information System (INIS)

Forero, Jose R; Castro, Henry I; Guerrero, Jairo A.

2009-01-01

In this study, three organic solvents (ethyl acetate, methanol and acetone) were used as co solvent in supercritical fluid extraction (SFE) of a mixture of pesticides with different physical and chemical properties present in soil. These pesticides were determined by gas chromatography with electronic micro capture detector μECD and nitrogen-phosphorus detector (NPD), coupled in parallel. The extractions were performed on spiked soil samples using supercritical carbon dioxide (CO 2 SC) as the extracting phase to 35 celsius degrade and 14 MPa, using 10 mL of each co solvent and it was found that methanol offers the greatest efficiency in the extraction process obtaining recovery values between 51.24 and 123.50%.

The rate of cerebral utilization of glucose, ketone bodies, and oxygen: a comparative in vivo study of infant and adult rats.

Science.gov (United States)

Dahlquist, G; Persson, B

1976-11-01

Cerebral blood flow (CBF) was measured by means of Celabeled microspheres in infant (20-day-old) and adult (3-month-old) rats, anesthetised with Na-5-ethyl-5-(1-methylpropyl)2-thiobarbituric acid. Cerebral arteriovenous differences of acetoacetate, D-beta-hydroxybutyrate, glucose, lactate, and oxygen and brain DNA content were determined in other groups of similarly treated infant and adult animals fed or starved for 48 or 72 hr. The mean CBF values of 0.48+/-0.04 and 0.62+/-0.07 ml/(g X min), +/- SEM, in infant and adult animals, respectively, were not significantly different. CBF was unaffected by starvation. At any given arterial concentration the cerebral arteriovenous difference of acetoacetate was significantly higher in infant than adult rats. The same was true for D-beta-hydroxybutyrate at arterial concentrations above 1 mmol/liter. There was an approximately linear relationship between arterial concentration of acetoacetate and its cerebral arteriovenous difference in both infant and adult rats. A similar relationship was found for D-beta-hydroxybutyrate only in infant animals. In the fed state, the cerebral uptake of glucose and ketone bodies (micromoles per (mg DNA X min)) was not different in infant and adult rats. During starvation, cerebral uptake of ketone bodies expressed as micromoles per (mg DNA X min) was higher in infant than adult rats, indicating a higher rate of utilization of ketone bodies per cell in these animals. For glucose, no such difference was found in either fed or starved groups (Table 3). The average percentage of the total cerebral uptake of substrates (micromoles per min) accounted for by ketone bodies increased in both infant and adult rats during starvation. This percentage value was clearly higher in infant than adult rats during starvation. After 72 hr of starvation the values were 38.8% and 15.2% in infant and adult rats, respectively (Fig. 3). Calculated cerebral metabolic rate for oxygen (CMRO2), assuming complete

Niobium Pentachloride Activation of Enone Derivatives: Diels-Alder and Conjugate Addition Products

Directory of Open Access Journals (Sweden)

Gil Valdo José da Silva

2002-05-01

Full Text Available Niobium pentachloride has proven to be a powerful activating agent for Diels-Alder or conjugate addition reactions of cycloenones. The Diels-Alder product was obtained only with an unsubstituted enone (cyclohexenone and the highly reactive diene cyclopentadiene; substituents in the b-position of enones seem to prevent Diels-Alder reaction: oxygenated substituents favor the formation of vinyl chlorides (ethyl ether or dichloromethane as solvents or enol ethers (ethyl acetate as solvent, while a methyl substituent prevents any kind of transformation with NbCl5. Less reactive dienes, furan and 2-methylfuran gave the conjugate addition products of the furan ring to the enone system.

Synthesis of two potential NK1-receptor ligands using [1-11C]ethyl iodide and [1-11C]propyl iodide and initial PET-imaging

Directory of Open Access Journals (Sweden)

Genchel Tove

2007-07-01

Full Text Available Abstract Background The previously validated NK1-receptor ligand [O-methyl-11C]GR205171 binds with a high affinity to the NK1-receptor and displays a slow dissociation from the receptor. Hence, it cannot be used in vivo for detecting concentration changes in substance P, the endogenous ligand for the NK1-receptor. A radioligand used for monitoring these changes has to enable displacement by the endogenous ligand and thus bind reversibly to the receptor. Small changes in the structure of a receptor ligand can lead to changes in binding characteristics and also in the ability to penetrate the blood-brain barrier. The aim of this study was to use carbon-11 labelled ethyl and propyl iodide with high specific radioactivity in the synthesis of two new and potentially reversible NK1-receptor ligands with chemical structures based on [O-methyl-11C]GR205171. Methods [1-11C]Ethyl and [1-11C]propyl iodide with specific radioactivities of 90 GBq/μmol and 270 GBq/μmol, respectively, were used in the synthesis of [O-methyl-11C]GR205171 analogues by alkylation of O-desmethyl GR205171. The brain uptake of the obtained (2S,3S-N-(1-(2- [1-11C]ethoxy-5-(3-(trifluoromethyl-4H-1,2,4-triazol-4-ylphenylethyl-2-phenylpiperidin-3-amine (I and (2S,3S-2-phenyl-N-(1-(2- [1-11C]propoxy-5-(3-(trifluoromethyl-4H-1,2,4-triazol-4-ylphenylethylpiperidin-3-amine (II was studied with PET in guinea pigs and rhesus monkeys and compared to the uptake of [O-methyl-11C]GR205171. Results All ligands had similar uptake distribution in the guinea pig brain. The PET-studies in rhesus monkeys showed that (II had no specific binding in striatum. Ligand (I had moderate specific binding compared to the [O-methyl-11C]GR205171. The ethyl analogue (I displayed reversible binding characteristics contrary to the slow dissociation rate shown by [O-methyl-11C]GR205171. Conclusion The propyl-analogue (II cannot be used for detecting changes in NK1-ligand levels, while further studies should be

Solvent free oxidation of primary alcohols and diols using thymine iron(III) catalyst.

Science.gov (United States)

Al-Hunaiti, Afnan; Niemi, Teemu; Sibaouih, Ahlam; Pihko, Petri; Leskelä, Markku; Repo, Timo

2010-12-28

In this study, we developed an efficient and selective iron-based catalyst system for the synthesis of ketones from secondary alcohols and carboxylic acids from primary alcohol. In situ generated iron catalyst of thymine-1-acetate (THA) and FeCl(3) under solvent-free condition exhibits high activity. As an example, 1-octanol and 2-octanol were oxidized to 1-octanoic acid and 2-octanone with 89% and 98% yields respectively.

Ternary liquid-liquid equilibria for mixtures of toluene + n-heptane + an ionic liquid

NARCIS (Netherlands)

Meindersma, G.W.; Podt, J.G.; de Haan, A.B.

2006-01-01

This research has been focused on a study of sulfolane and four ionic liquids as solvents in liquid–liquid extraction. Liquid–liquid equilibria data were obtained for mixtures of (sulfolane or 4-methyl-N-butylpyridinium tetrafluoroborate ([mebupy]BF4) or 1-ethyl-3-methylimidazolium ethylsulfate

Investigation of a potential scintigraphic marker of apoptosis: radioiodinated Z-Val-Ala-DL-Asp(O-methyl)-fluoromethyl ketone

Energy Technology Data Exchange (ETDEWEB)

Haberkorn, Uwe E-mail: uwe_haberkorn@med.uni-heidelberg.de; Kinscherf, Ralf; Krammer, Peter H.; Mier, Walter; Eisenhut, Michael

2001-10-01

The imaging of apoptosis represents an attractive diagnostic goal in the area of tumor therapy, degenerative diseases and organ transplantation. Since caspases play a key role during the early period of the intracellular signal cascade of cells undergoing apoptosis we considered benzyloxycarbonyl-Val-Ala-DL-Asp(O-methyl)-fluoromethyl ketone [Z-VAD-fmk], a pan-caspase inhibitor, as a potential apoptosis imaging agent. Applying the Tl(TFA){sub 3}/[{sup 131}I]iodide method Z-VAD-fmk was successfully labeled at the benzyloxycarbonyl protecting group. The success of radioiodination, however, depended on the presence of carrier iodide resulting in specific radioactivities of 2.6 GBq/{mu}mol and the formation of a mixture of the 2- and 4-iodophenyl derivative (61%) which could not be separated by HPLC. Uptake measurements were performed with Morris hepatoma cells (MH3924Atk8) which showed expression of the Herpes Simplex Virus thymidine kinase (HSVtk) gene. Apoptosis was induced by treatment of the cells with 25 {mu}M ganciclovir. The TUNEL assay revealed 1.3{+-}0.3 and 23{+-}1.1% apoptotic cells immediately and 24 h after therapy, respectively. A two-fold increase of [{sup 131}I]IZ-VAD-fmk uptake was found at the end of treatment with the HSVtk/suicide system which constantly remained elevated for the following 4 hours. The slow cellular influx and lack of uptake saturation of [{sup 131}I]IZ-VAD-fmk are evidence for simple diffusion as transport mechanism. In addition, the absolute cellular uptake of [{sup 131}I]IZ-VAD-fmk was found to be low. This quality was related to the rather high lipophilicity of [{sup 131}I]IZ-VAD-fmk causing unspecific binding to macromolecules in the medium. Instead of using an inhibitor, synthetic caspase substrates are currently investigated which may accumulate in the apoptotic cell by metabolic trapping thereby enhancing the imaging signal.

Colorimetric Recognition of Aldehydes and Ketones.

Science.gov (United States)

Li, Zheng; Fang, Ming; LaGasse, Maria K; Askim, Jon R; Suslick, Kenneth S

2017-08-07

A colorimetric sensor array has been designed for the identification of and discrimination among aldehydes and ketones in vapor phase. Due to rapid chemical reactions between the solid-state sensor elements and gaseous analytes, distinct color difference patterns were produced and digitally imaged for chemometric analysis. The sensor array was developed from classical spot tests using aniline and phenylhydrazine dyes that enable molecular recognition of a wide variety of aliphatic or aromatic aldehydes and ketones, as demonstrated by hierarchical cluster, principal component, and support vector machine analyses. The aldehyde/ketone-specific sensors were further employed for differentiation among and identification of ten liquor samples (whiskies, brandy, vodka) and ethanol controls, showing its potential applications in the beverage industry. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Vanillin as a modulator agent in SMART test: inhibition in the steps that precede N-methyl-N-nitrosourea-, N-ethyl-N-nitrosourea-, ethylmethanesulphonate- and bleomycin-genotoxicity.

Science.gov (United States)

Sinigaglia, Marialva; Lehmann, Maurício; Baumgardt, Paula; do Amaral, Viviane Souza; Dihl, Rafael Rodrigues; Reguly, Maria Luíza; de Andrade, Heloísa Helena Rodrigues

2006-09-05

Vanillin (VA), the world's major flavoring compound used in food industry and confectionery products - that has antimutagenic and anticarcinogenic activity against a variety of mutagenic/carcinogenic agents - was tested for the interval between the formation of premutational lesion and it is finalization as a DNA lesion. The overall findings using co-treatment protocols in SMART test suggest that VA can lead to a significant protection against the general genotoxicity of ethylmethanesulphonate (EMS), N-ethyl-N-nitrosourea (ENU), N-methyl-N-nitrosourea (MNU) and bleomycin sulphate (BLEO). Considering MNU, ENU and EMS the desmutagenic activity observed could result from VA-stimulation of detoxification, via induction of glutathione S-transferase. However, the protector effect related to BLEO could be attributed to its powerful scavenger ability, which has the potential to prevent oxidative damage induced by BLEO.

Fragrance material review on 1-[5(or 6)-methyl-7(or 8)-1-(methylethyl)bicyclo[2.2.2]oct-5-en-2-yl]ethan-1-one.

Science.gov (United States)

Scognamiglio, J; Letizia, C S; Api, A M

2013-12-01

A toxicologic and dermatologic review of 1-[5(Or 6)-Methyl-7(or 8)-1-(methylethyl)bicyclo[2.2.2]oct-5-en-2-yl]ethan-1-one when used as a fragrance ingredient is presented. 1-[5(Or 6)-Methyl-7(or 8)-1-(methylethyl)bicyclo[2.2.2]oct-5-en-2-yl]ethan-1-one is a member of the fragrance structural group Alkyl Cyclic Ketones. These fragrances can be described as being composed of an alkyl, R1, and various substituted and bicyclic saturated or unsaturated cyclic hydrocarbons, R2, in which one of the rings may include up to 12 carbons. Alternatively, R2 may be a carbon bridge of C2-C4 carbon chain length between the ketone and cyclic hydrocarbon. This review contains a detailed summary of all available toxicology and dermatology papers that are related to this individual fragrance ingredient and is not intended as a stand-alone document. Available data for 1-[5(Or 6)-Methyl-7(or 8)-1-(methylethyl)bicyclo[2.2.2]oct-5-en-2-yl]ethan-1-one were evaluated then summarized and includes physical properties, acute toxicity, skin irritation, mucous membrane (eye) irritation, skin sensitization, phototoxicity, photoallergy, and genotoxicity, data. A safety assessment of the entire Alkyl Cyclic Ketones will be published simultaneously with this document; please refer to Belsito et al., Belsito, D., Bickers, D., Bruze, M., Calow, P., Dagli, M., Fryer, A.D., Greim, H., Miyachi, Y., Saurat, J.H., Sipes, I.G., 2013. A Toxicologic and Dermatologic Assessment of Alkyl Cyclic Ketones When Used as Fragrance Ingredients. (submitted for publication)). for an overall assessment of the safe use of this material and all Alkyl Cyclic Ketones in fragrances. Copyright © 2013 Elsevier Ltd. All rights reserved.

The effect of different aluminum alloy surface compositions on barrier anodic film formation

International Nuclear Information System (INIS)

Panitz, J.K.G.; Sharp, D.J.

1984-01-01

The authors have grown barrier anodic coatings on samples of aluminum alloy with different elemental surface compositions. In one series of experiments, they characterized the surface composition present on 6061 aluminum alloy samples after different chemical treatments including a detergent-water and methyl-ethyl ketone solvent clean, a 50% nitric acid-water etch, and a concentrated nitric acid-ammonium bifluoride etch. They anodized samples which were prepared similarly to those analyzed to evaluate the practical effects of the three different surface compositions. The anodization voltage rise time to 950V at constant current was used as a figure of merit. The solvent cleaned and the 50% nitric acid etched samples required, respectively, 113% and 41% more time to reach 950V than the concentrated nitric acidammonium bifloride etched samples. In a second series of experiments, they alternately anodized groups of either 6061 or 1100 (commercially pure) aluminum alloy, observed rise times to 950V, and measured chloride ion concentrations in the electrolyte. Longer rise times and higher chloride ion concentrations were observed for the 1100 samples. It was observed that the chloride ion concentration fell from initially high levels when 6061 samples were anodized. The results of both series of experiments augment the results of other investigators, who report that the surface species initially present on aluminum have a significant effect on anodic film formation

Brahmarasayana protects against Ethyl methanesulfonate or Methyl methanesulfonate induced chromosomal aberrations in mouse bone marrow cells

Directory of Open Access Journals (Sweden)

Guruprasad Kanive

2012-08-01

Full Text Available Abstract Background Ayurveda, the traditional Indian system of medicine has given great emphasis to the promotion of health. Rasayana is one of the eight branches of Ayurveda which refers to rejuvenant therapy. It has been reported that rasayanas have immuno-modulatory, antioxidant and antitumor functions, however, the genotoxic potential and modulation of DNA repair of many rasayanas have not been evaluated. Methods The present study assessed the role of Brahmarasayana (BR on Ethyl methanesulfonate (EMS-and Methyl methanesulfonate (MMS-induced genotoxicity and DNA repair in in vivo mouse test system. The mice were orally fed with BR (5 g or 8 mg / day for two months and 24 h later EMS or MMS was given intraperitoneally. The genotoxicity was analyzed by chromosomal aberrations, sperm count, and sperm abnormalities. Results The results have revealed that BR did not induce significant chromosomal aberrations when compared to that of the control animals (p >0.05. On the other hand, the frequencies of chromosomal aberrations induced by EMS (240 mg / kg body weight or MMS (125 mg / kg body weight were significantly higher (p Conclusion The effect of BR, as it relates to antioxidant activity was not evident in liver tissue however rasayana treatment was observed to increase constitutive DNA base excision repair and reduce clastogenicity. Whilst, the molecular mechanisms of such repair need further exploration, this is the first report to demonstrate these effects and provides further evidence for the role of brahmarasayana in the possible improvement of quality of life.

Karakterstik Serapan Suara Komposit Polyester Berpenguat Serat Tapis Kelapa

OpenAIRE

Astika, I Made; Dwijana, I Gusti Komang

2016-01-01

The purpose of this study is to investigate of sound absorption of coconut filter fiber composites. The research material made with coconut filter fiber as reinforcement and matrix resin unsaturated polyester (UPRs) type Yukalac BQTN 157 with 1% hardener types MEKPO (Methyl Ethyl Ketone Peroxide) and fiber treatment by  0,5% KMnO4. Production methods is poltrusion and the variations of fiber volume fraction are 20, 25 and 30% and fiber length are 5, 10 and 15 mm. Testing of sound absorpt...

Vibrational spectroscopic (FT-IR, FT-Raman) and quantum mechanical study of 4-(2-chlorophenyl)-2-ethyl-9-methyl-6H-thieno[3,2-f] [1,2,4]triazolo[4,3-a][1,4] diazepine

Science.gov (United States)

Kuruvilla, Tintu K.; Prasana, Johanan Christian; Muthu, S.; George, Jacob

2018-04-01

The spectroscopic properties of 4-(2-chlorophenyl)-2-ethyl-9-methyl-6H-thieno [3,2-f] [1,2,4] triazolo [4,3-a] [1,4] diazepine were investigated in the present study using FT-IR and FT-Raman techniques. The results obtained were compared with quantum mechanical methods, as it serves as an important tool in interpreting and predicting vibrational spectra. The optimized molecular geometry, the vibrational wavenumbers, the infrared intensities and Raman scattering were calculated using density functional theory B3LYP method with 6-311++g (d,p) basis set. All the experimental results were in line with the theoretical data. The molecular electrostatic potential (MEP) and HOMO LUMO energies of the title compound were accounted. The results indicated that the title compound has a lower softness value (0.27) and high electrophilicity index (4.98) hence describing its biological activity. Further, natural bond orbital was also analyzed as part of the work. Fukui functions were calculated in order to explain the chemical selectivity or the reactivity site in 4-(2-chlorophenyl)-2-ethyl-9-methyl-6H-thieno [3,2-f] [1,2,4] triazolo [4,3-a] [1,4] diazepine. The thermodynamic properties of the title compound were closely examined at different temperatures. It revealed the correlations between heat capacity (C), entropy (S) and enthalpy changes (H) with temperatures. The paper further explains that the title compound can act as good antidepressant through molecular docking studies.

Synergistic solvent extraction investigation of Am (III), Eu (III), Zn(II), and Cs(I), using 2-heptyl-2-methyl-nonanoic acid mixed with different organophosphorus compounds from nitrate media. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

El-Naggar, H A; Ramadan, A; Abdel-Fattah, A [Nuclear Chemistry Department, Hot Laboratories Center, Atomic Energy Authority, Cairo (Egypt)

1996-03-01

Extraction studies for investigating the effect of mixing 2-heptyl-2-methyl nonanoic acid (HA) with a number of organophosphorus compounds; namely tributyl phosphate (TBP), terphenyl phosphate oxide (TPPO); tri octyl phosphine oxide (TOPO) or bis-2-(ethyl hexyl) phosphoric acid (HDEHP) in benzene on the extraction of trace elements Am(III), Eu(III), Zn(II), and Cs(I) from nitrate media of ionic strength, I=0.1 M were carried out. The effect of adding different organophosphorus compounds to HA was tested to account for the presence or absence of the phenomenon of synergism. It was found that TBP, TPPO, and TOPO causing some antagonistic effects for the elements studied. Extraction enhancement was only observed with bis- (2-ethyl-hexyl) -phosphoric acid (HDEHP) for all the elements investigated. The extraction mechanisms as well as the thermodynamic parameters for the mixed extracted species are discussed. 19 figs.

Synergistic solvent extraction investigation of Am (III), Eu (III), Zn(II), and Cs(I), using 2-heptyl-2-methyl-nonanoic acid mixed with different organophosphorus compounds from nitrate media. Vol. 3

International Nuclear Information System (INIS)

El-Naggar, H.A.; Ramadan, A.; Abdel-Fattah, A.

1996-01-01

Extraction studies for investigating the effect of mixing 2-heptyl-2-methyl nonanoic acid (HA) with a number of organophosphorus compounds; namely tributyl phosphate (TBP), terphenyl phosphate oxide (TPPO); tri octyl phosphine oxide (TOPO) or bis-2-(ethyl hexyl) phosphoric acid (HDEHP) in benzene on the extraction of trace elements Am(III), Eu(III), Zn(II), and Cs(I) from nitrate media of ionic strength, I=0.1 M were carried out. The effect of adding different organophosphorus compounds to HA was tested to account for the presence or absence of the phenomenon of synergism. It was found that TBP, TPPO, and TOPO causing some antagonistic effects for the elements studied. Extraction enhancement was only observed with bis- (2-ethyl-hexyl) -phosphoric acid (HDEHP) for all the elements investigated. The extraction mechanisms as well as the thermodynamic parameters for the mixed extracted species are discussed. 19 figs

Degradation of lipids in yeast (Saccharomyces cerevisiae) at the early phase of organic solvent-induced autolysis

International Nuclear Information System (INIS)

Ishida-Ichimasa, Michiko

1978-01-01

Initial stage of organic solvent-induced autolysis in yeast was studied with 14 C-acetate labeled cells. In the case of toluene-induced autolysis, primary cell injury which was estimated by leakage of UV absorbing substances from cell accompanied rapid deacylation of phospholipids. Lysophospholipids did not occur during autolysis. When autolysis was induced by addition of ethyl acetate, phospholipids of yeast cells were not degraded so much. Ethyl acetate rather inhibited yeast phospholipase activity under the condition tested. (auth.)

Solvent extraction of silver(I) from dilute cyanide solutions with 2,4-dihydroxyacetophenone thiosemicarbazone

International Nuclear Information System (INIS)

Reddy, A.V.; Reddy, Y.K.; Reddy, G.S.

1986-01-01

The solvent extraction of silver(I) was carried out in 0.5M nitric acid in the presence of cyanide by 2,4-dihydroxyacetophenone thiosemicarbazone (DATS). Ethyl acetate was used as a solvent and quantitative recovery was possible with 12.5-fold excess of the reagent in a single extraction. In this medium silver(I) forms a 2:2 complex (metal:ligand) with DATS. The effect of diverse ions on the extraction of silver(I) was investigated. (author)

Is there an astrocyte-neuron ketone body shuttle?

Science.gov (United States)

Guzmán, M; Blázquez, C

2001-01-01

Ketone bodies can replace glucose as the major source of brain energy when glucose becomes scarce. Although it is generally assumed that the liver supplies extrahepatic tissues with ketone bodies, recent evidence shows that astrocytes are also ketogenic cells. Moreover, the partitioning of fatty acids between ketogenesis and ceramide synthesis de novo might control the survival/death decision of neural cells. These findings support the notion that astrocytes might supply neurons with ketone bodies in situ, and raise the possibility that astrocyte ketogenesis is a cytoprotective pathway.

Degradation of methyl and ethyl mercury into inorganic mercury by other reactive oxygen species besides hydroxyl radical

Energy Technology Data Exchange (ETDEWEB)

Suda, Ikuo; Takahashi, Hitoshi (Kumamoto Univ. Medical School (Japan). Inst. for Medical Immunology)

1992-01-01

Degradation of methyl mercury (MeHg) and ethyl Hg (EtHg) with reactive oxygens was studied in vitro by using peroxidase-hydrogen peroxide (H{sub 2}O{sub 2})-halide and rose bengal-ultraviolet light A systems. For this purpose, the direct determination method for inorganic Hg was employed. Both systems could effectively degrade EtHg, and MeHg to some extent. Degradation of MeHg and EtHg with the myeloperoxidase (MPO)-H{sub 2}O{sub 2}-chloride system was inhibited by MPO inhibitors (cyanide and azide), catalase, hypochlorous acid (HOCl) scavengers (glycine, alanine, serine and taurine), 1,4-diazabicyclo(2,2,2)octane and 2,5-dimethylfuran, but not by hydroxyl radical scavengers (ethanol and mannitol). Iodide was more effective than chloride as the halide component. Lactoperoxidase (LPO) could substitute for MPO in the iodide, but not the chloride system. With MPO-H{sub 2}O{sub 2}-chloride, MPO-H{sub 2}O{sub 2}-iodide and LPO-H{sub 2}O{sub 2}-iodide systems, we observed the increased degradation of EtHg in deuterium oxide (D{sub 2}O) medium better than that in H{sub 2}O medium. The D{sub 2}O effect upon MeHg degradation was extremely weak. These results suggested that HOCl (or HOI) might be also capable of degrading MeHg and EtHg, besides the hydroxyl radical already reported by us. Singlet oxygen could degrade EtHg but not MeHg. (orig.).

Preparation and properties of titania based ionogels synthesized using ionic liquid 1-ethyl-3-methyl imidazolium thiocyanate

Energy Technology Data Exchange (ETDEWEB)

Verma, Y.L.; Tripathi, A.K.; Shalu; Singh, V.K.; Balo, L.; Gupta, H.; Singh, S.K.; Singh, R.K., E-mail: rajendrasingh.bhu@gmail.com

2017-06-15

Highlights: • Synthesis of titania based ionogels using non-aqueous sol-gel process. • Ionogels are found to be mesoporous structure with uniform pore size distribution. • Ionic liquid extracted TiO{sub 2} matrix reveals the anatase phase of TiO{sub 2}. • Properties of ionic liquid are found to change in TiO{sub 2} matrix. - Abstract: Present study reports the synthesis of titania (TiO{sub 2}) based ionogels using ionic liquid (IL) 1-ethyl-3-methyl imidazolium thiocyanate ([EMIM][SCN]) by non-aqueous sol-gel process. Ionogels are characterized using N{sub 2} adsorption-desorption, TGA, DSC, SEM, TEM, XRD, and FTIR. N{sub 2}-sorption results show that TiO{sub 2} matrices have meso-pores with uniform pore size distribution. Thermal studies reveal that thermal stability of confined IL decreases while the glass transition temperature (T{sub g}) is found to increase. XRD patterns show that IL containing TiO{sub 2} matrices exhibit amorphous (weak crystalline peaks) nature however after extraction of IL from ionogel, it shows the crystalline (anatase) phase of TiO{sub 2} which has also been found from SAED pattern. SEM micrographs reveal that as the amount of IL is increased, TiO{sub 2} particles are found to agglomerate. FTIR results indicate that the vibrational frequencies of confined IL are found to shift due to interaction of IL molecules with titania pore wall surface.

Volumetric properties of room temperature ionic liquid 1. The system of {1-methyl-3-ethylimidazolium ethyl sulfate+water} at temperature in the range (278.15 to 333.15) K

International Nuclear Information System (INIS)

Lu Xingmei; Xu Weiguo; Gui Jinsong; Li Huawei; Yang Jiazhen

2005-01-01

This paper reports densities of aqueous solutions of ionic liquid (IL) 1-methyl-3-ethylimidazolium ethyl sulfate (EMISE) that were measured gravimetrically at temperatures (278.15 to 333.15) K. The values of the apparent molar volume, φ V B and partial molar volume, V-bar B, were determined and apparent molar expansibilities φ E=((∂φ B )/∂T)) p of EMISE and the coefficients of thermal expansion of the solutions, α, were calculated. The values of the apparent molar volume, φ V B , were fitted by the method of least-squares to a Pitzer's equation to determine the parameters, β MX (0)V , β MX (1)V , and C MX V

Going the distance with ethyl alcohol

International Nuclear Information System (INIS)

Hairston, D.W.

1995-01-01

If all had gone according to plan, ethyl alcohol would be in the driver's seat now, cruising down the highway and getting ready to speed into high gear. Instead, this renewable fuel, chemical reagent and solvent is navigating a complex obstacle course, watching warily for sharp turns and mixed signals. Globally, the supply and demand for all grades of ethyl alcohol is awry. Production of industrial-grade material is running at full throttle and prices are going up. Much of the upheaval over ethanol can be traced to the US Environmental Protection Agency and the renewable oxygenate standard (ROS) of the Clean Air Act. Under ROS, 15% of oxygenates used in gasoline sold this year was to be derived from a renewable source. Next month, that percentage was to have been doubled to 30%. Enticed by projections of upwards of 2 billion gal/yr of fermentation alcohol to comply with ROS, producers rushed to expand capacity. But to the producers' dismay, EPA was forced to backpedal on ROS. When representatives of the petroleum industry filed suit and won a stay, EPA rescinded its ROS regulation and ethanol producers were left in the lurch. High prices for corn is also putting the squeeze on inventories of industrial alcohol. Synthetic ethanol production, from ethylene for example, is booming, however. This paper discusses the ethanol market factors

Control of postharvest Botrytis fruit rot of strawberry by volatile organic compounds of Candida intermedia.

Science.gov (United States)

Huang, R; Li, G Q; Zhang, J; Yang, L; Che, H J; Jiang, D H; Huang, H C

2011-07-01

A study was conducted to identify volatile organic compounds or volatiles produced by Candida intermedia strain C410 using gas chromatography-mass spectrometry, and to determine efficacy of the volatiles of C. intermedia in suppression of conidial germination and mycelial growth of Botrytis cinerea and control of Botrytis fruit rot of strawberry. Results showed that, among 49 volatiles (esters, alcohols, alkenes, alkanes, alkynes, organic acids, ketones, and aldehydes) identified from C. intermedia cultures on yeast extract peptone dextrose agar, two compounds, 1,3,5,7-cyclooctatetraene and 3-methyl-1-butanol, were the most abundant. Synthetic chemicals of 1,3,5,7-cyclooctatetraene; 3-methyl-1-butanol; 2-nonanone; pentanoic acid, 4-methyl-, ethyl ester; 3-methyl-1-butanol, acetate; acetic acid, pentyl ester; and hexanoic acid, ethyl ester were highly inhibitory to conidial germination and mycelial growth of B. cinerea. Inhibition of conidial germination and mycelial growth of B. cinerea by volatiles of C. intermedia was also observed. Meanwhile, results showed that incidence and severity of Botrytis fruit rot of strawberry was significantly (P intermedia cultures or C. intermedia-infested strawberry fruit. These results suggest that the volatiles of C. intermedia C410 are promising biofumigants for control of Botrytis fruit rot of strawberry.

Method of estimating changes in vapor concentrations continuously generated from two-component organic solvents.

Science.gov (United States)

Hori, Hajime; Ishidao, Toru; Ishimatsu, Sumiyo

2010-12-01

We measured vapor concentrations continuously evaporated from two-component organic solvents in a reservoir and proposed a method to estimate and predict the evaporation rate or generated vapor concentrations. Two kinds of organic solvents were put into a small reservoir made of glass (3 cm in diameter and 3 cm high) that was installed in a cylindrical glass vessel (10 cm in diameter and 15 cm high). Air was introduced into the glass vessel at a flow rate of 150 ml/min, and the generated vapor concentrations were intermittently monitored for up to 5 hours with a gas chromatograph equipped with a flame ionization detector. The solvent systems tested in this study were the methanoltoluene system and the ethyl acetate-toluene system. The vapor concentrations of the more volatile component, that is, methanol in the methanol-toluene system and ethyl acetate in the ethyl acetate-toluene system, were high at first, and then decreased with time. On the other hand, the concentrations of the less volatile component were low at first, and then increased with time. A model for estimating multicomponent organic vapor concentrations was developed, based on a theory of vapor-liquid equilibria and a theory of the mass transfer rate, and estimated values were compared with experimental ones. The estimated vapor concentrations were in relatively good agreement with the experimental ones. The results suggest that changes in concentrations of two-component organic vapors continuously evaporating from a liquid reservoir can be estimated by the proposed model.

Overmodulation Control in the Optimization of a H-PDLC Device with Ethyl Eosin as Dye

Directory of Open Access Journals (Sweden)

Manuel Ortuño

2013-01-01

Full Text Available The response of a H-PDLC device is improved by means of a two-step method. First, component optimization—initiator system, crosslinker, and cosolvent—enables the diffraction efficiency of the hologram to be maximized. Second, the use of N-methyl-2-pyrrolidone in combination with N-vinyl-2-pyrrolidone prevents the overmodulation in photopolymers containing ethyl eosin.

Equilibrium data on ethanol-water-solvent ternaries

Directory of Open Access Journals (Sweden)

I. Kirbaslar

2000-06-01

Full Text Available Experimental liquid-liquid equilibria of water-ethanol-1-nonanol and water-ethanol-1-decanol systems were investigated at 303.16± 0.20 K. The reliability of the experimental tie-line data was ascertained by using Othmer-Tobias and Hand plots. Distribution coefficients (Di and separation factors (S were evaluated for the immiscibility region. It is concluded that the solvents with high boiling point, 1-nonanol and 1-decanol, are suitable separating agents for dilute aqueous ethyl alcohol solutions.

INIBIÇÃO DE SALMONELLA POR EXTRATO DE ALECRIM (Rosmarinus officinalis: OBTENÇÃO DE EXTRATOS DE ALECRIM EM SOLVENTES ORGÂNICOS INHIBITION OF Salmonella BY ROSEMARY (Rosmarinus officinalis EXTRACTS: ORGANIC SOLVENTS ROSEMARY EXTRACT OBTENTION

Directory of Open Access Journals (Sweden)

Maria Célia Lopes Torres

2007-09-01

Full Text Available

Com o objetivo de se obter um extrato de alecrim em solvente orgânico, a ser utilizado na inibição de Salmonella, em alimentos, foram testados quatro tipos de solventes, a saber: metanol, etanol, acetona e hexano. Na obtenção dos extratos foi adotada a técnica recomendada para determinação de lipídeos, conforme as NORMAS ANALÍTICAS DO INSTITUTO ADOLFO LUTZ (1976. A análise dos resultados evidenciou um excelente desempenho do metanol, não sendo contudo recomendada a utilização em produtos alimentares em virtude da sua toxidez. Também o etanol apresentou elevados índices de extração, sem os inconvenientes associados ao uso do metanol, sendo por isto o solvente indicado para a continuidade do estudo proposto.

Aiming to obtain a rosemary extract in organic solvent to be used in Salmonella inhibition, in food, were tested four kinds of solvents, namely: methane alcohol, ethyl alcohol, acetone and hexane. It was used the recommended technique for lipids determination in extracts determination according to the analytic rules used by Instituto Adolfo Lutz. Analysis results showed an excellent performance for methane alcohol, but its use is not recommended in feed products due to its toxicity. Ethyl alcohol presented also elevated extraction indexes without inconvenients associated to methane alcohol use, by this reason being a solvent indicated for continuity to the proposed study.

α-Alkylation of ketones with primary alcohols driven by visible light and bimetallic gold and palladium nanoparticles supported on transition metal oxide

Energy Technology Data Exchange (ETDEWEB)

Bai, Meifen; Xin, Hui; Guo, Zhi; Guo, Dapeng; Wang, Yan; Zhao, Peng; Li, Jingyi, E-mail: lijingyicn@163.com