Damage effects and mechanisms of proton irradiation on methyl silicone rubber

International Nuclear Information System (INIS)

Zhang, L.X.; He, Sh.Y.; Xu, Zh.; Wei, Q.

2004-01-01

A study was performed on the damage effects and mechanisms of proton irradiation with 150 keV energy to space-grade methyl silicone rubber. The changes in surface morphology, mechanical properties, infrared attenuated total reflection (ATR) spectrum, mass spectrum and pyrolysis gas chromatography-mass spectrum (PYGC-MS) indicated that, under lower fluence, the proton radiation would induce cross-linking effect, resulting in an increase in tensile strengths and hardness of the methyl silicon rubber. However, under higher proton fluence, the radiation-induced degradation, which decreased the tensile strengths and hardness, became a dominant effect. A macromolecular-network destruction model for the silicone rubber radiated with the protons was proposed

Environmental effect of rapeseed oil ethyl ester

International Nuclear Information System (INIS)

Makareviciene, V.; Janulis, P.

2003-01-01

Exhaust emission tests were conducted on rapeseed oil methyl ester (RME), rapeseed oil ethyl ester (REE) and fossil diesel fuel as well as on their mixtures. Results showed that when considering emissions of nitrogen oxides (NO x ), carbon monoxide (CO) and smoke density, rapeseed oil ethyl ester had less negative effect on the environment in comparison with that of rapeseed oil methyl ester. When fuelled with rapeseed oil ethyl ester, the emissions of NO x showed an increase of 8.3% over those of fossil diesel fuel. When operated on 25-50% bio-ester mixed with fossil diesel fuel, NO x emissions marginally decreased. When fuelled with pure rapeseed oil ethyl ester, HC emissions decreased by 53%, CO emissions by 7.2% and smoke density 72.6% when compared with emissions when fossil diesel fuel was used. Carbon dioxide (CO 2 ) emissions, which cause greenhouse effect, decreased by 782.87 g/kWh when rapeseed oil ethyl ester was used and by 782.26 g/kWh when rapeseed oil methyl ester was used instead of fossil diesel fuel. Rapeseed oil ethyl ester was more rapidly biodegradable in aqua environment when compared with rapeseed oil methyl ester and especially with fossil diesel fuel. During a standard 21 day period, 97.7% of rapeseed oil methyl ester, 98% of rapeseed oil ethyl ester and only 61.3% of fossil diesel fuel were biologically decomposed. (author)

STABILITY OF EMULSIFIER-FREE EMULSION COPOLYMERIZATION OF METHYL METHACRYLATE/ BUTYL ACRYLATE/SODIUM MONO(ETHYL POLYOXYETHYLENE) MALEATE

Institute of Scientific and Technical Information of China (English)

Mao-gen Zhang; Zhi-xue Weng; Zhi-ming Huang; Zu-ren Pan

1999-01-01

A series of new water-soluble bifunctional comonomers having both carboxyl and alkyl polyoxyethylene groups, such as sodium mono(ethyl polyoxyethylene) maleate (ZE series) with various molecular weights of polyoxyethylene ethyl ether, were synthesized and characterized. The effects of the structural factor, the amount and feeding mode of the comonomers, the initiator concentration and polymerization temperature on the stability of emulsifier-free emulsion copolymerization of methyl methacrylate (MMA) and butyl acrylate (BA) in the presence of a small amount of ZE with potassium persulfate as initiator were investigated. Stable, almost monodispersed MMA/BA/ZE emulsifier-free latex particles were prepared.

A comparative study of the chemical kinetics of methyl and ethyl propanoate

KAUST Repository

Farooq, Aamir

2014-10-01

High temperature pyrolysis of methyl propanoate (CH3CH 2C(O)OCH3) and ethyl propanoate (CH3CH 2C(O)OCH2CH3) was studied behind reflected shock waves at temperatures of 1250-1750 K and pressure of 1.5 atm. Species time-histories were recorded for CO, CO2, C2H4, and H2O using laser absorption methods over a test time of 1 ms. Pyrolysis of methyl propanoate (MP) appears to be faster than that of ethyl propanoate (EP) under the present experimental conditions, where CO and CO 2 reach their plateau values faster for MP at a specific temperature and fuel concentration. Higher plateau values are reached for CO in case of MP while the CO2 levels are similar for the two ester fuels. Ethylene production is larger for EP due to the presence of six-centered ring elimination reaction that produces ethylene and propanoic acid. Very little H2O is produced during MP pyrolysis in contrast with appreciable H2O production from EP. Sensitivity and rate-of-production analyses were carried out to identify key reactions that affect the measured species profiles. Previous kinetic mechanisms of Yang et al. (2011) [1,2] and Metcalf et al. (2009, 2007) [3,4] were used as base models and then refined to propose a new MP/EP pyrolysis mechanism. © 2014 Elsevier Ltd. All rights reserved.

A comparative study of the chemical kinetics of methyl and ethyl propanoate

KAUST Repository

Farooq, Aamir; Davidson, D.F.; Hanson, R.K.; Westbrook, C.K.

2014-01-01

High temperature pyrolysis of methyl propanoate (CH3CH 2C(O)OCH3) and ethyl propanoate (CH3CH 2C(O)OCH2CH3) was studied behind reflected shock waves at temperatures of 1250-1750 K and pressure of 1.5 atm. Species time-histories were recorded for CO, CO2, C2H4, and H2O using laser absorption methods over a test time of 1 ms. Pyrolysis of methyl propanoate (MP) appears to be faster than that of ethyl propanoate (EP) under the present experimental conditions, where CO and CO 2 reach their plateau values faster for MP at a specific temperature and fuel concentration. Higher plateau values are reached for CO in case of MP while the CO2 levels are similar for the two ester fuels. Ethylene production is larger for EP due to the presence of six-centered ring elimination reaction that produces ethylene and propanoic acid. Very little H2O is produced during MP pyrolysis in contrast with appreciable H2O production from EP. Sensitivity and rate-of-production analyses were carried out to identify key reactions that affect the measured species profiles. Previous kinetic mechanisms of Yang et al. (2011) [1,2] and Metcalf et al. (2009, 2007) [3,4] were used as base models and then refined to propose a new MP/EP pyrolysis mechanism. © 2014 Elsevier Ltd. All rights reserved.

A Simple and Fast Method for the Production and Characterization of Methylic and Ethylic Biodiesels from Tucum Oil via an Alkaline Route

Directory of Open Access Journals (Sweden)

Marcelo Firmino de Oliveira

2011-01-01

Full Text Available A simple, fast, and complete route for the production of methylic and ethylic biodiesel from tucum oil is described. Aliquots of the oil obtained directly from pressed tucum (pulp and almonds were treated with potassium methoxide or ethoxide at 40°C for 40 min. The biodiesel form was removed from the reactor and washed with 0.1 M HCl aqueous solution. A simple distillation at 100°C was carried out in order to remove water and alcohol species from the biodiesel. The oxidative stability index was obtained for the tucum oil as well as the methylic and ethylic biodiesel at 6.13, 2.90, and 2.80 h, for storage times higher than 8 days. Quality control of the original oil and of the methylic and ethylic biodiesels, such as the amount of glycerin produced during the transesterification process, was accomplished by the TLC, GC-MS, and FT-IR techniques. The results obtained in this study indicate a potential biofuel production by simple treatment of tucum, an important Amazonian fruit.

Searching for trans ethyl methyl ether in Orion KL★,★★

Science.gov (United States)

Tercero, B.; Cernicharo, J.; López, A.; Brouillet, N.; Kolesniková, L.; Motiyenko, R. A.; Margulès, L.; Alonso, J. L.; Guillemin, J.-C.

2015-01-01

We report on the tentative detection of trans ethyl methyl ether (tEME), t-CH3CH2OCH3, through the identification of a large number of rotational lines from each one of the spin states of the molecule towards Orion KL. We also search for gauche-trans-n-propanol, Gt-n-CH3CH2CH2OH, an isomer of tEME in the same source. We have identified lines of both species in the IRAM 30 m line survey and in the ALMA Science Verification data. We have obtained ALMA maps to establish the spatial distribution of these species. Whereas tEME mainly arises from the compact ridge component of Orion, Gt-n-propanol appears at the emission peak of ethanol (south hot core). The derived column densities of these species at the location of their emission peaks are ≤(4.0 ± 0.8) × 1015 cm−2 and ≤(1.0 ± 0.2)× 1015 cm−2 for tEME and Gt-n-propanol, respectively. The rotational temperature is ~100 K for both molecules. We also provide maps of CH3OCOH, CH3CH2OCOH, CH3OCH3, CH3OH, and CH3CH2OH to compare the distribution of these organic saturated O-bearing species containing methyl and ethyl groups in this region. Abundance ratios of related species and upper limits to the abundances of non-detected ethers are provided. We derive an abundance ratio N(CH3OCH3)/N(tEME) ≥ 150 in the compact ridge of Orion. PMID:26869726

Thermophysical properties of biodiesel and related systems: Low-pressure vapor + liquid equilibrium of methyl/ethyl soybean biodiesel

International Nuclear Information System (INIS)

Veneral, Josamaique G.; Junior, Dirceu L.R.; Mazutti, Marcio A.; Voll, Fernando A.P.; Cardozo-Filho, Lúcio; Corazza, Marcos L.; Silva, Edson A.; Oliveira, J. Vladimir

2013-01-01

Highlights: • Boiling point temperatures for soybean FAME and FAEE measured in the pressure range of (6.7 to 66.7) kPa. • Investigated systems presented a non-ideal behavior, with positive deviations from Raoult’s law. • Experimental data satisfactorily represented by the UNIQUAC model. -- Abstract: In this work, experimental boiling point temperatures for pseudo-binaries (methyl/ethyl biodiesel + methanol/ethanol) and pseudo-ternaries (methyl/ethyl biodiesel + methanol/ethanol + glycerol/water) systems were measured at several pressures ranging from (6.7 to 66.7) kPa using an Othmer-type ebulliometer. The systems investigated show a non-ideal behavior, with positive deviations from Raoult’s law. It was observed that the addition of up to 10 wt% of alcohol (methanol or ethanol) led to a significant decrease in the boiling point temperature of the systems. The UNIQUAC model was successfully used to represent the experimental results, with an overall average deviation between experimental and calculated boiling temperature values of 0.004%

4-Hydroxy-3-methyl-6-phenylbenzofuran-2-carboxylic acid ethyl ester derivatives as potent anti-tumor agents.

Science.gov (United States)

Hayakawa, Ichiro; Shioya, Rieko; Agatsuma, Toshinori; Furukawa, Hidehiko; Naruto, Shunji; Sugano, Yuichi

2004-01-19

Based on the structure of 4-hydroxy-3-methyl-6-phenylbenzofuran-2-carboxylic acid ethyl ester (1), which exhibits selective cytotoxicity against a tumorigenic cell line, (2,4-dimethoxyphenyl)-(4-hydroxy-3-methyl-6-phenylbenzofuran-2-yl)-methanone (18m) was designed and synthesized as a biologically stable derivative containing no ester group. Although the potency of 18m was almost the same as our initial hit compound 1, 18m is expected to last longer in the human body as an anticancer agent.

Effect of 200 keV proton irradiation on the properties of methyl silicone rubber

International Nuclear Information System (INIS)

Zhang Lixin; Xu Zhou; Wei Qiang; He Shiyu

2006-01-01

The effects of 200 keV proton irradiation on methyl silicone rubber were studied. The changes in surface morphology, mechanical properties, cross-linking density, glass transition temperature, infrared attenuated total reflection spectrum and mass spectrum indicated that, at lower fluence, the proton irradiation induced cross-linking, resulting in an increase in tensile strength and hardness of the methyl silicone rubber. However, at higher proton fluence, radiation-induced degradation, which decreased the tensile strength and hardness, became dominant. A macromolecular-network destruction model for silicone rubber irradiated with protons was proposed

Methyl and ethyl soybean esters production

Energy Technology Data Exchange (ETDEWEB)

Pighinelli, Anna Leticia Montenegro Turtelli; Park, Kil Jin; Zorzeto, Thais Queiroz [Universidade Estadual de Campinas (FEAGRI/UNICAMP), SP (Brazil). Fac. de Engenharia Agricola], E-mail: annalets@feagri.unicamp.br; Bevilaqua, Gabriela [Universidade Estadual de Campinas (IQ/UNICAMP), SP (Brazil). Inst. de Quimica

2008-07-01

Biodiesel is a fuel obtained from triglycerides found in nature, like vegetable oils and animal fats. Nowadays it has been the subject of many researches impulses by the creation of the Brazilian law that determined the blend of 2% of biodiesel with petrodiesel. Basically, there are no limitations on the oilseed type for chemical reaction, but due to high cost of this major feedstock, it is important to use the grain that is available in the region of production. Soybean is the oilseed mostly produced in Brazil and its oil is the only one that is available in enough quantity to supply the current biodiesel demand. The objective of this work was to study the effects of reaction time and temperature on soybean oil transesterification reaction with ethanol and methanol. A central composite experimental design with five variation levels was used and response surface methodology applied for the data analysis. The statistical analysis of the results showed that none of the factors affected the ethyl esters production. However, the methyl esters production suffered the influence of temperature (linear effect), reaction time (linear and quadratic) and interaction of these two variables. None of the generated models showed significant regression consequently it was not possible to build the response surface. The experiments demonstrated that methanol is the best alcohol for transesterification reactions and the ester yield was up to 85%. (author)

(Vapour + liquid) equilibria, volumetric and compressibility behaviour of binary and ternary aqueous solutions of 1-hexyl-3-methylimidazolium chloride, methyl potassium malonate, and ethyl potassium malonate

International Nuclear Information System (INIS)

Sadeghi, Rahmat; Mahdavi, Adibeh

2012-01-01

Highlights: ► VLE and volumetry of binary and ternary [C 6 mim][Cl], MPM and EPM aqueous solutions. ► Constant a w lines show small negative deviation from the linear isopiestic relation. ► Solute–water interactions follow the order: EPM > MPM > [C 6 mim][Cl]. ► MPM and EPM have a very weak salting-out effect on [C 6 mim][Cl] aqueous solutions. - Abstract: (Vapour + liquid) equilibrium data (water activity, vapour pressure, osmotic coefficient, and activity coefficient) of binary aqueous solutions of 1-hexyl-3-methylimidazolium chloride ([C 6 mim][Cl]), methyl potassium malonate, and ethyl potassium malonate and ternary {[C 6 mim][Cl] + methyl potassium malonate} and {[C 6 mim][Cl] + ethyl potassium malonate} aqueous solutions were obtained through the isopiestic method at T = 298.15 K. These results reveal that the ionic liquid behaves as surfactant-like and aggregates in aqueous solutions at molality about 0.4 mol · kg −1 . The constant water activity lines of all the ternary systems investigated show small negative deviations from the linear isopiestic relation (Zdanovskii–Stokes–Robinson rule) derived using the semi-ideal hydration model. The density and speed of sound measurements were carried out on solutions of methyl potassium malonate and ethyl potassium malonate in water and of [C 6 mim][Cl] in aqueous solutions of 0.25 mol · kg −1 methyl potassium malonate and ethyl potassium malonate at T = (288.15 to 308.15) K at atmospheric pressure. From the experimental density and speed of sound data, the values of the apparent molar volume, apparent molar isentropic compressibility and excess molar volume were evaluated and from which the infinite dilution apparent molar volume and infinite dilution apparent molar isentropic compressibility were calculated at each temperature. Although, there are no clear differences between the values of the apparent molar volume of [C 6 mim][Cl] in pure water and in methyl potassium malonate or ethyl

Biological effects of methyl and ethyl mercury compounds used as disinfectants for seed-grain on domestic and wild life

Energy Technology Data Exchange (ETDEWEB)

Tejning, S

1971-01-01

A short survey of the harmful effects of methyl and ethyl mercury on wild and domestic life and on man since the introduction of these compounds in plant protection is given. The biological effects of methyl mercury in birds are illustrated by experiments in hens concerning its accumulation in their organs and plumage, its elimination in eggs and excrements and its influence on the health of the birds, their laying habits and egg production including the occurrence of embryonic damages and the hatchability. Attention is drawn to the ability of methyl mercury to cause genetical disorders. 14 references, 1 figure, 1 table.

Determination of acetone and methyl ethyl ketone in water

Science.gov (United States)

Tai, D.Y.

1978-01-01

Analytical procedures for the determination of acetone and methyl ethyl ketone in water samples were developed. Concentrations in the milligram-per-liter range were determined by injecting an aqueous sample into the analysis system through an injection port, trapping the organics on Tenax-GC at room temperature, and thermally desorbing the organics into a gas chromatograph with a flame ionization detector for analysis. Concentrations in the microgram-per-liter range were determined by sweeping the headspace vapors over a water sample at 50C, trapping on Tenax-GC, and thermally desorbing the organics into the gas chromatograph. The precision for two operators of the milligram-per-liter concentration procedure, expressed as the coefficient of variation, was generally less than 2 percent for concentrations ranging from 16 to 160 milligrams per liter. The precision from two operators of the microgram-per-liter concentration procedure was between 2 and 4 percent for concentrations of 20 and 60 micrograms per liter. (Woodard-USGS)

γ-radiation-induced degradation of poly(dimethylsilylene-co-methylphenylsilylene) in cyclohexane and THF-ethyl alcohol solution

International Nuclear Information System (INIS)

Oka, Kunio; Nakao, Ren

1989-01-01

γ-Irradiation of high molecular weight poly(dimethylsilylene-co-methyl-phenylsilylene) in cyclohexane and THF-ethyl alcohol solutions was carried out in order to study the degradation mechanism. The G s value (number of chain scissions per 100eV radiation energy absorbed) depends on the dose rate but not on the polysilane concentration. No insertion products of dimethylsilylene or methylphenylsilylene into ethyl alcohol were detected, indicating that no silylene evolution mechanism was involved. IR analysis of the irradiated polymer suggests that chain scission occurs preferentially at the methylphenylsilylene unit. The resulting polysilane (135 Mrad irradiated) has chains of about 20 silicon atoms containing siloxane bonds and hydroxy groups. All of the results indicate that the polysilane degrades by a free radical mechanism. (author)

Effect of ethyl-, methyl- and hydroxyethyl-nitrosourea on the mouse testis

Energy Technology Data Exchange (ETDEWEB)

Oakberg, E.F.; Crosthwait, C.D.

1983-01-01

Hybrid male 101 x C3HF/sub 1/ mice were given intraperitoneal injections of methyl-, ethyl- and hydroxyethyl-nitrosourea and killed 3-16 days later. All compounds were similar in that all differentiating spermatogonia from type A/sub 1/ to early type B were killed by 50 mg/kg and higher doses of ENU and by 75 mg/kg MNU. Cells exposed to leptotene to 100 and 250 mg/kg ENU and 455 mg/kg HENU showed a delayed response with degeneration in pachytene 5 days later. Labeling prior to exposure to ENU indicated that the effect of stage of the mitotic cycle on sensitivity to cell killing is less marked than for radiation. This may be the explanation for the s-shaped mutation induction curve obtained with ENU in contrast to the humped dose-response curve observed for radiation.

Kinetic Modelling and Experimental Study of Small Esters: Methyl Acetate and Ethyl Acetate

KAUST Repository

Ahmed, Ahfaz; Mehl, Marco; Lokachari, Nitin; Nilsson, Elna J.K.; Konnov, Alexander A.; Wagnon, Scott W.; Pitz, William J.; Curran, Henry J.; Roberts, William L.; Sarathy, Mani

2017-01-01

A detailed chemical kinetic mechanism comprising methyl acetate and ethyl acetate has been developed based on the previous work by Westbrook et al. [1]. The newly developed kinetic mechanism has been updated with new reaction rates from recent theoretical studies. To validate this model, shock tube experiments measuring ignition delay time have been conducted at 15 & 30 bar and equivalence ratio 0.5, 1.0 and 2.0. Another set of experiments measuring laminar burning velocity was also performed on a heat flux burner at atmospheric pressure over wide range of equivalence ratios [~0.7-1.4]. The new mechanism shows significant improvement in prediction of experimental data over earlier model across the range of experiments.

Kinetic Modelling and Experimental Study of Small Esters: Methyl Acetate and Ethyl Acetate

KAUST Repository

Ahmed, Ahfaz

2017-12-14

A detailed chemical kinetic mechanism comprising methyl acetate and ethyl acetate has been developed based on the previous work by Westbrook et al. [1]. The newly developed kinetic mechanism has been updated with new reaction rates from recent theoretical studies. To validate this model, shock tube experiments measuring ignition delay time have been conducted at 15 & 30 bar and equivalence ratio 0.5, 1.0 and 2.0. Another set of experiments measuring laminar burning velocity was also performed on a heat flux burner at atmospheric pressure over wide range of equivalence ratios [~0.7-1.4]. The new mechanism shows significant improvement in prediction of experimental data over earlier model across the range of experiments.

Crystal structure of (Z-ethyl 3-[2-(5-methyl-7-nitro-1H-indole-2-carbonylhydrazinylidene]butanoate

Directory of Open Access Journals (Sweden)

Amal Errossafi

2015-09-01

Full Text Available The reaction of 5-methyl-7-nitro-1H-indole-2-carbohydrazide with ethyl acetoacetate yielded the title molecule, C16H18N4O5, in which the indole ring is almost planar, with the greatest deviation from the mean plane being 0.006 (2 Å. The nine atoms of the indole ring are almost perpendicular to the mean plane through the ethyl acetate group, as indicated by the dihedral angle of 87.02 (4° between them. In the crystal, centrosymmetric supramolecular dimers are formed via N—H...O hydrogen bonds and eight-membered amide {...HNCO}2 synthons. These are consolidated into a three-dimensional architecture by C—H...O contacts, and by π–π interactions between six-membered rings [inter-centroid distance = 3.499 (2 Å].

TRANSPORT PROPERTIES FOR 1-ETHYL-3-METHYLIMIDAZOLIUM n-ALKYL SULFATES: POSSIBLE EVIDENCE OF GROTTHUSS MECHANISM

International Nuclear Information System (INIS)

García-Garabal, S.; Vila, J.; Rilo, E.; Domínguez-Pérez, M.; Segade, L.; Tojo, E.; Verdía, P.; Varela, L.M.; Cabeza, O.

2017-01-01

The objective of this work was to study the effect of the temperature and the lengthening of the linear alkyl chain of the anion in the transport physical properties of the pure ionic liquids 1-ethyl-3-methyl imidazolium n-alkyl sulphate (being n = 0, 1, 2, 4, 6 and 8). Density, viscosity and electrical conductivities were measured at atmospheric pressure in a wide temperature range. In the bibliography, data existed for these magnitudes for all ionic liquids studied but none of these had information about the electrical conductivity of 1-ethyl-3-methyl imidazolium n-alkyl sulfate whith n = 0, 4, 6 and 8. The experimental results show clearly 1-ethyl-3-methyl imidazolium hydrogen sulphate cannot be considered part of the 1-ethyl-3-methyl imidazolium n-alkyl sulphate family because of its hydrogen bonding ability. Results of density and viscosity behave as expected. However, in the case of the electrical conductivity due to the lack of alkyl chain in the hydrogen sulfate we expected to get extreme values but in practise, we obtained intermediate values between 1-ethyl-3-methyl imidazolium butyl sulphate and 1-ethyl-3-methyl imidazolium hexyl sulphate. This suggests that a Grotthus mechanism exists as result of a protonic current in addition to ionic conductivity, being Waldeńs plot consistent with this idea.

Distribution of methyl and ethyl adducts following alkylation with monofunctional alkylating agents.

Science.gov (United States)

Beranek, D T

1990-07-01

Alkylating agents, because of their ability to react directly with DNA either in vitro or in vivo, or following metabolic activation as in the case of the dialkylnitrosamines, have been used extensively in studying the mechanisms of mutagenicity and carcinogenicity. Their occurrence is widespread in the environment and human exposure from natural and pollutant sources is universal. Since most of these chemicals show varying degrees of both carcinogenicity and mutagenicity, and exhibit compound-specific binding patterns, they provide an excellent model for studying molecular dosimetry. Molecular dosimetry defines dose as the number of adducts bound per macromolecule and relates the binding of these adducts to the human mutagenic or carcinogenic response. This review complies DNA alkylation data for both methylating and ethylating agents in a variety of systems and discusses the role these alkylation products plays in molecular mutagenesis.

Dielectric and conformational studies of hydrogen bonded 2-ethoxyethanol and ethyl methyl ketone system

Science.gov (United States)

Pattebahadur, Kanchan. L.; Deshmukh, S. D.; Mohod, A. G.; Undre, P. B.; Patil, S. S.; Khirade, P. W.

2018-05-01

The Dielectric constant, density and refractive index of binary mixture of 2-ethoxy ethanol (2-EE) with ethyl methyl ketone (EMK) including those of the pure liquids were measured for 11 concentrations at 25°C temperature. The experimental data is used to calculate the Excess molar volume, Excess dielectric constant, Kirkwood correlation factor and Bruggemann factor. The excess parameters results were fitted to the Redlich-Kister type polynomial equation to derive its fitting coefficient. The Kirkwood correlation factor of the mixture has been discussed to yield information about solute solvent interaction. The Bruggeman plot shows a deviation from linearity. The FT-IR spectra of pure and their binary mixtures are also studied.

Efficacy of scalp hair decontamination following exposure to vapours of sulphur mustard simulants 2-chloroethyl ethyl sulphide and methyl salicylate

OpenAIRE

Spiandore , Marie; Piram , Anne; Lacoste , Alexandre; Prevost , P.; Maloni , Pascal; TORRE , Franck; Asia , L.; Josse , D.; Doumenq , Pierre

2017-01-01

International audience; Chemical warfare agents are an actual threat and victims' decontamination is a main concern when mass exposure occurs. Skin decontamination with current protocols has been widely documented, as well as surface decontamination. However, considering hair ability to trap chemicals in vapour phase, we investigated hair decontamination after exposure to sulphur mustard simulants methyl salicylate and 2-chloroethyl ethyl sulphide. Four decontamination protocols were tested o...

Synthesis, characterization and catalytic performance of mixed nanoferrites submitted to transesterification and esterification reaction using methyl and ethyl route for biodiesel production

International Nuclear Information System (INIS)

Dantas, Joelda; Leal, Elvia; Mapossa, Antonio Benjamim; Silva, Adriano Sant'Ana; Costa, Ana Cristina Figueiredo de Melo

2016-01-01

The mixed nanoferrites of Ni_0_._5Zn_0_._5Fe_2O_4 and Ni_0_._2Cu_0_._3Zn_0_._5Fe_2O_4 were synthesized by combustion reaction using urea as fuel and a conical reactor as heating source in batches of 10 g, and then tested as heterogeneous nanocatalysts in the transesterification and esterification reaction of soya bean oil using the methyl and ethyl routes to biodiesel production. During the synthesis the time and temperature of the reactions were measured, and the evolved gases and the color of the emitted flames were observed. The samples were characterized by XRD, EDX, FTIR, SEM/EDS, BET and gas chromatography. The reaction tests were carried out with 10 g of oil for 1 h, oil:alcohol molar ratio of 1:12, 2 % (w/w) of catalyst, and conducted at 180 °C. The XRD patterns and the FTIR spectra revealed the presence of the inverse spinel phase type B(AB)_2O_4. The morphology showed the formation of agglomerates with fragile morphology and high surface area. The chromatographic analysis produced excellent results in the esterification reactions for both samples in the tested conditions, with special emphasis on Ni_0_._5Zn_0_._5Fe_2O_4, whose conversions were of 91.4 % in methyl esters and of 77.8 % in ethyl esters, while the Ni_0_._2Cu_0_._3Zn_0_._5Fe_2O_4 sample showed conversion of 75.1 and 65.1 %, respectively. The conversions in the methyl and ethyl transesterification were of 14 and 2 % of the Ni_0_._5Zn_0_._5Fe_2O_4 sample, and of 11 and 3 % for the Ni_0_._2Cu_0_._3Zn_0_._5Fe_2O_4 sample. (author)

Phase equilibria and the thermodynamic properties of methyl and ethyl esters of carboxylic acids. 1. Methyl n-butanoate and ethyl propanoate

International Nuclear Information System (INIS)

Agafonova, Luba E.; Varushchenko, Raisa M.; Druzhinina, Anna I.; Polyakova, Olga V.

2012-01-01

Highlights: ► Heat capacities, fusion properties of CH 3 OC(O)C 3 H 7 measured by adiabatic calorimetry. ► The temperature dependence of vapour pressure determined by comparative ebulliometry. ► The thermodynamic functions derived from experiment and calculated by DFT method. ► Extending vapour pressure of moderate interval to entire region of liquid. ► An increment of the entropy of carbonyl group was defined from experimental data. - Abstract: The heat capacity of methyl n-butanoate in crystalline and liquid states was measured by vacuum adiabatic calorimetry over the temperature range from (8 to 372) K. The triple point temperature, the enthalpy and entropy of fusion, and the purity of the sample were determined. The saturated vapour pressure and the boiling temperatures were determined by comparative ebulliometry in the “atmospheric” pressure range 10.8 ⩽ (p/kPa) ⩽ 99.6. The normal boiling temperature, T n.b , and the enthalpy of vaporization at T = 298.15 K and T n.b were derived. The thermodynamic functions (absolute entropy and changes of the enthalpy, and Gibbs free energy) were derived for the solid and liquid states in the temperature range studied and for the ideal gas state at T = 298.15 K. The ideal gas heat capacities and the absolute entropies of methyl n-butanoate (MeBu) and ethyl propanoate (EtPr) were calculated by statistical thermodynamics on the basis of the molecular constants determined by the use of density functional theory on the B3LYP level. The experimental vapour pressure of MeBu and EtPr of moderate temperature intervals, Δ exp T = (59/65) K, were extended to the entire range of the liquids, Δ liq T = (364.7/345.7) K by the methods of the corresponding states law and simultaneous treatment of the pT-parameters and low-temperature heat capacities of the ideal gas and liquid, respectively. An additive contribution of the carbonyl group CO–(C, O) connected with C and O atoms was determined for calculation of the

Structural study of ethyl 3-methyl-9-oxo-3-azabicyclo63.3.19nonane-1-carboxylate by two-dimensional NMR spectroscopy

Science.gov (United States)

Arias-Pérez, M. S.; Alejo, A.; Gálvez, E.; Pérez, S. M.; Santos, M. J.

1995-04-01

Ethyl 3-methyl-9-oxo-3-azabicyclo[3.3.1]nonane-1-carboxylate has been studied by 1H, 13C and 2D NMR spectroscopy in order to establish its conformational behaviour. The combined use of COSY and 1H- 13C correlation spectra helped in the unambiguous and complete assignment of the bicyclic carbon and proton resonances. It is found that the piperidone ring displays a slightly fattened chair conformation with the N-methyl group in the equatorial position, while a twist-chair form seems to be favoured for the cyclohexanone one. Two preferred orientations migth be proposed for the ethoxycarbonyl moiety.

Chemo-Enzymatic Synthesis of Chiral Epoxides Ethyl and Methyl (S-3-(Oxiran-2-ylpropanoates from Renewable Levoglucosenone: An Access to Enantiopure (S-Dairy Lactone

Directory of Open Access Journals (Sweden)

Aurélien A. M. Peru

2016-07-01

Full Text Available Chiral epoxides—such as ethyl and methyl (S-3-(oxiran-2-ylpropanoates ((S-1a/1b—are valuable precursors in many chemical syntheses. Until recently, these compounds were synthesized from glutamic acid in four steps (deamination, reduction, tosylation and epoxide formation in low to moderate overall yield (20%–50%. Moreover, this procedure requires some harmful reagents such as sodium nitrite ((ecotoxic and borane (carcinogen. Herein, starting from levoglucosenone (LGO, a biobased chiral compound obtained through the flash pyrolysis of acidified cellulose, we propose a safer and more sustainable chemo-enzymatic synthetic pathway involving lipase-mediated Baeyer-Villiger oxidation, palladium-catalyzed hydrogenation, tosylation and treatment with sodium ethoxide/methoxide as key steps. This route afforded ethyl and methyl (S-3-(oxiran-2-ylpropanoates in 57% overall yield, respectively. To demonstrate the potentiality of this new synthetic pathway from LGO, the synthesis of high value-added (S-dairy lactone was undertaken from these epoxides and provided the target in 37% overall yield from LGO.

A library synthesis of 4-hydroxy-3-methyl-6-phenylbenzofuran-2-carboxylic acid ethyl ester derivatives as anti-tumor agents.

Science.gov (United States)

Hayakawa, Ichiro; Shioya, Rieko; Agatsuma, Toshinori; Furukawa, Hidehiko; Naruto, Shunji; Sugano, Yuichi

2004-09-06

As a result of a hit-to-lead program using a technique of solution-phase parallel synthesis, a highly potent (2,4-dimethoxyphenyl)-[6-(3-fluorophenyl)-4-hydroxy-3-methylbenzofuran-2-yl]methanone (15b) was synthesized as an optimized derivative of 4-hydroxy-3-methyl-6-phenylbenzofuran-2-carboxylic acid ethyl ester (1), which was discovered as a screening hit from small-molecule libraries and exhibited selective cytotoxicity against a tumorigenic cell line.

Investigations into the chemistry, toxicology, metabolism and possible mode of action of O-ethyl S-methyl ethylphosphonothioate

International Nuclear Information System (INIS)

Hur, J.H.

1989-01-01

The chemical and metabolic oxidation of O-ethyl S-methyl ethylphosphonthioate (1) as a model compound was studied. This compound has the following toxicological properties: LD 50 (rat) 4.6 mg/kg, LD 50 (HF) 14.0 ug/g; k i (BAChE) = 303, k i (HFAChE) = 623. 13 C- and 31 P-NMR were mainly used in this study. The chemical oxidation of 1 with m-CPBA in CDCl 3 resulted in the formation of O-ethyl ethylphosphonic acid (2), O-ethyl ethylphosphinyloxymethylsulfonate (3) and O-ethyl ethylphosphonic acid anhydride (4). However, oxidation reaction of the model compound 1 with MPPA in D 2 O gave 2 and methylsulfonic acid. 1 was incubated in vitro with rat liver microsomal oxidase, and 2 and methylsulfenic acid were observed along with 1. For the in vivo study, a number of houseflies were treated with 14ug/g (LD 50 level) of 1. Analysis of the extracts of metabolic products provided evidence of the formation of 2. The existence of 1 S-oxide was demonstrated by use of a trapping method and the observation of oxidation products. The S-oxide has been proposed as a possible active intermediate responsible for the high toxicity of 1 to animals. However, owing to its instability it is unlikely that the S-oxide intermediate would persist in an aqueous biological environment long enough to attack the target enzyme. 4 was shown to have high toxicity to the rat and housefly and was also a potent anticholinesterase against BAChE and HFAChE . The presence of 4 was observed directly by the monitoring experiments during the chemical oxidation in aqueous conditions. This provided evidence that this metabolite is stable enough to attack the target site in biological systems. The anhydride 4 is proposed as the active metabolite in in vivo systems, responsible for high toxicity of 1

Leaching of Oil from Tuna Fish Liver by Using Solvent of Methyl-Ethyl Ketone

Directory of Open Access Journals (Sweden)

Mirna Rahmah Lubis

2013-12-01

Full Text Available Research of oil leaching from Tuna Fish Liver has been carried out by extracting of tuna fish liver in soxhlet by using methyl-ethyl ketone as solvent. Liver of fresh tuna fish is blended, put into soxhlet, and extracted at temperatures of 60oC, 65oC, 70oC, 75oC, and 80oC. After obtaining the oil, separation between solvent and oil is carried out by distillation. Oil obtained is analyzed by testing the yield, acid number, Iodine value, viscosity, and its impurities content. Yield obtained is influenced by temperature and time of leaching. Both variables indicates that the higher the variables, the more fish liver oil obtained. Maximum yield obtained is 25.552% at operating condition of leaching temperature 80oC, and leaching duration of 5 hours.

Experimental density, viscosity, interfacial tension and water solubility of ethyl benzene-α-methyl benzyl alcohol–water system

International Nuclear Information System (INIS)

Barega, Esayas W.; Zondervan, Edwin; Haan, André B. de

2013-01-01

Highlights: • Properties were measured for MBA (methyl benzyl alcohol)-EB (ethyl benzene)-water. • MBA concentration was found to influence all the properties strongly. • The water solubility, density, and viscosity increased at high MBA concentration. • The interfacial tension decreased sharply at high MBA concentration. • MBA dictates the phase separation and mass transfer of the ternary system. -- Abstract: Density, viscosity, interfacial tension, and water solubility were measured for the (α-methyl benzyl alcohol (MBA) + Ethyl benzene (EB)) system at different concentrations of MBA in contact with water and sodium hydroxide solution (0.01 mol · kg −1 ) as aqueous phases. The properties were measured to identify the component which plays a governing role in changing the physical properties relevant to mass transfer and phase separation of the ternary system. The concentration of MBA was found to be the major factor influencing all the properties. The water solubility, the density, and the viscosity increased notably at higher concentrations of MBA; while, the interfacial tension decreased strongly. The use of 0.01 mol · kg −1 NaOH as an aqueous phase resulted in a decrease of the interfacial tension and a minor decrease in the water solubility. The density data were correlated using a quadratic mixing rule to describe the influence of concentration at any temperature. The viscosity data are correlated using the Nissan and Grunberg and Katti-Chaudhri equations. The Szyzkowski’s equation was used to correlate the interfacial tension data. The water solubility data were described using an exponential relationship. All the correlations described the experimental physical property data adequately

Effect of silicon and acibenzolar-s-methyl on colored cotton plants infested or not with Aphis gossypii Glover (Hemiptera, Aphididae

Directory of Open Access Journals (Sweden)

Eliana Alcantra

2011-06-01

Full Text Available Effect of silicon and acibenzolar-s-methyl on colored cotton plants infested or not with Aphis gossypii Glover (Hemiptera, Aphididae. The aphid Aphis gossypii is an insect pest that causes damage mainly at the beginning of the cotton plant development. The effect of resistance inductors silicon and acibenzolar-s-methyl (ASM on the development of colored cotton plants were researched in the presence and absence of A. gossypii. Three colored cotton cultivars were sown in pots and individually infested with 25 apterous aphids, 13 days after the application of the inductors. Fifteen days after plant emergence, the silicon was applied at a dosage equivalent to 3 t/ha and acibenzolar-s-methyl in 0.2% solution of the product BION 500®. After 21 days of infestation the following parameters were evaluated: plant height, stem diameter, dry matter of aerial part and root, and total number of aphids replaced. It was verified that the plant height was reduced in the presence of aphids and all variables were negatively affected by the application of ASM. However, silicon did not affect plant development.

Formation of silicon carbide by laser ablation in graphene oxide-N-methyl-2-pyrrolidone suspension on silicon surface

Science.gov (United States)

Jaleh, Babak; Ghasemi, Samaneh; Torkamany, Mohammad Javad; Salehzadeh, Sadegh; Maleki, Farahnaz

2018-01-01

Laser ablation of a silicon wafer in graphene oxide-N-methyl-2-pyrrolidone (GO-NMP) suspension was carried out with a pulsed Nd:YAG laser (pulse duration = 250 ns, wavelength = 1064 nm). The surface of silicon wafer before and after laser ablation was studied using optical microscopy, scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX). The results showed that the ablation of silicon surface in liquid by pulsed laser was done by the process of melt expulsion under the influence of the confined plasma-induced pressure or shock wave trapped between the silicon wafer and the liquid. The X-ray diffraction‌ (XRD) pattern of Si wafer after laser ablation showed that 4H-SiC layer is formed on its surface. The formation of the above layer was also confirmed by Raman spectroscopy, and X-ray photoelectron spectroscopy‌ (XPS), as well as EDX was utilized. The reflectance of samples decreased with increasing pulse energy. Therefore, the morphological alteration and the formation of SiC layer at high energy increase absorption intensity in the UV‌-vis regions. Theoretical calculations confirm that the formation of silicon carbide from graphene oxide and silicon wafer is considerably endothermic. Development of new methods for increasing the reflectance without causing harmful effects is still an important issue for crystalline Si solar cells. By using the method described in this paper, the optical properties of solar cells can be improved.

Potentiation of 2,5-hexanedione neurotoxicity by methyl ethyl ketone

International Nuclear Information System (INIS)

Ralston, W.H.; Hilderbrand, R.L.; Uddin, D.E.; Andersen, M.E.; Gardier, R.W.

1985-01-01

Chronic oral administration of a combination of 2.2 mmol methyl ethyl ketone (MEK) and 2.2 mmol 2,5-hexanedione (2,5-HD)/kg/day, 5 days/week resulted in more rapid onset of motor deficits than did chronic dosing with 2.2 mmol 2,5-HD/kg/day alone. In kinetic studies blood time courses of 2,5-HD were determined in rats in the presence and absence of MEK. Concomitant administration of MEK reduced blood 2,5-HD clearance and increased the area under the curve (AUC) for the blood 2,5-HD. In companion experiments with 2,5-[1,6- 14 C]HD as a tracer, neural and nonneural tissues were examined 72 hr following the last treatment at Weeks 1, 2, and 3 of chronic administration of 2,5-HD alone or in combination with an equimolar dose of MEK. Rats treated with 2,5-[ 14 C]HD alone or in combination with MEK demonstrated no difference in total or trichloroacetic acid-precipitable radioactivity in blood, in liver homogenates, or in neurofilament-enriched fractions from sciatic nerve and spinal cord. The data support a suggestion that the potentiation of hexacarbon neurotoxicity by MEK is the result of the persistence of the neurotoxic metabolite in the blood and not the enhanced metabolism of parent hexacarbon to 2,5-HD

SPECTROSCOPIC CHARACTERIZATION AND DETECTION OF ETHYL MERCAPTAN IN ORION

International Nuclear Information System (INIS)

Kolesniková, L.; Alonso, J. L.; Daly, A. M.; Tercero, B.; Cernicharo, J.; Gordon, B. P.; Shipman, S. T.

2014-01-01

New laboratory data of ethyl mercaptan, CH 3 CH 2 SH, in the millimeter- and submillimeter-wave domains (up to 880 GHz) provided very precise values of the spectroscopic constants that allowed the detection of gauche-CH 3 CH 2 SH toward Orion KL. This identification is supported by 77 unblended or slightly blended lines plus no missing transitions in the range 80-280 GHz. A detection of methyl mercaptan, CH 3 SH, in the spectral survey of Orion KL is reported as well. Our column density results indicate that methyl mercaptan is ≅ 5 times more abundant than ethyl mercaptan in the hot core of Orion KL

SPECTROSCOPIC CHARACTERIZATION AND DETECTION OF ETHYL MERCAPTAN IN ORION

Energy Technology Data Exchange (ETDEWEB)

Kolesniková, L.; Alonso, J. L.; Daly, A. M. [Grupo de Espectroscopía Molecular (GEM), Edificio Quifima, Laboratorios de Espectroscopía y Bioespectroscopía, Parque Científico UVa, Unidad Asociada CSIC, Universidad de Valladolid, E-47011 Valladolid (Spain); Tercero, B.; Cernicharo, J. [Departamento de Astrofísica, Centro de Astrobiología CAB, CSIC-INTA, Ctra. de Torrejón a Ajalvir km 4, E-28850 Madrid (Spain); Gordon, B. P.; Shipman, S. T., E-mail: lucie.kolesnikova@uva.es, E-mail: jlalonso@qf.uva.es, E-mail: adammichael.daly@uva.es, E-mail: terceromb@cab.inta-csic.es, E-mail: jcernicharo@cab.inta-csic.es, E-mail: brittany.gordon@ncf.edu, E-mail: shipman@ncf.edu [Division of Natural Sciences, New College of Florida, Sarasota, FL 34243 (United States)

2014-03-20

New laboratory data of ethyl mercaptan, CH{sub 3}CH{sub 2}SH, in the millimeter- and submillimeter-wave domains (up to 880 GHz) provided very precise values of the spectroscopic constants that allowed the detection of gauche-CH{sub 3}CH{sub 2}SH toward Orion KL. This identification is supported by 77 unblended or slightly blended lines plus no missing transitions in the range 80-280 GHz. A detection of methyl mercaptan, CH{sub 3}SH, in the spectral survey of Orion KL is reported as well. Our column density results indicate that methyl mercaptan is ≅ 5 times more abundant than ethyl mercaptan in the hot core of Orion KL.

Density, refraction index and vapor–liquid equilibria of N-methyl-2-hydroxyethylammonium butyrate plus (methyl acetate or ethyl acetate or propyl acetate) at several temperatures

International Nuclear Information System (INIS)

Alvarez, V.H.; Mattedi, S.; Aznar, M.

2013-01-01

Highlights: ► Densities, refraction indices and VLE were measured for ester + m-2-HEAB mixtures. ► V E , apparent molar volumes and thermal expansion coefficients were calculated. ► Peng–Robinson EoS + Wong–Sandler mixing rule + COSMO-SAC predicted the data. -- Abstract: This paper reports the densities, refraction indices, and vapor liquid equilibria for binary systems ester + N-methyl-2-hydroxyethylammonium butyrate (m-2-HEAB): methyl acetate (1) + m-2-HEAB (2), ethyl acetate (1) + m-2-HEAB and propyl acetate (1) + m-2-HEAB (2). The excess molar volumes, deviations in the refraction index, apparent molar volumes, and thermal expansion coefficients for the binary systems were fitted to polynomial equations. The Peng–Robinson equation of state, coupled with the Wong–Sandler mixing rule, is used to describe the experimental data. Since the predictive activity coefficient model COSMO-SAC is used in the Wong–Sandler mixing rule, the resulting thermodynamic model is a completely predictive one. The prediction results for the density and for the vapor–liquid equilibria have a deviation lower than 1.0% and 1.1%, respectively

Enhanced susceptibility of a transposable-element-bearing strain of Drosophila melanogaster to somatic eye-color mutations by ethyl nitrosourea, methyl nitrosourea, and X-rays

International Nuclear Information System (INIS)

Ryo, H.; Kondo, S.; Rasmuson, B.

1983-01-01

A strain of Drosophila with the genes z and w + plus a transposable element (TE) is about 3 times more sensitive than a strain without TE toward somatic eye-color mutations after larval exposure to ethyl nitrosourea, methyl nitrosourea and X-rays. The assay system with TE is simple, reliable, and sensitive for detecting somatic mutations induced in vivo by mutagens. (orig.)

Synthesis, and anticonvulsant activity of new amides derived from 3-methyl- or 3-ethyl-3-methyl-2,5-dioxo-pyrrolidin-1-yl-acetic acids.

Science.gov (United States)

Obniska, Jolanta; Rapacz, Anna; Rybka, Sabina; Góra, Małgorzata; Kamiński, Krzysztof; Sałat, Kinga; Żmudzki, Paweł

2016-04-15

This paper describes the synthesis of the library of 22 new 3-methyl- and 3-ethyl-3-methyl-2,5-dioxo-pyrrolidin-1-yl-acetamides as potential anticonvulsant agents. The maximal electroshock (MES) and the subcutaneous pentylenetetrazole (scPTZ) seizure models were used for screening all the compounds. The 6 Hz model of pharmacoresistant limbic seizures was applied for studying selected derivatives. Six amides were chosen for pharmacological characterization of their antinociceptive activity in the formalin model of tonic pain as well as local anesthetic activity was assessed in mice. The pharmacological data indicate on the broad spectra of activity across the preclinical seizure models. Compounds 10 (ED50=32.08 mg/kg, MES test) and 9 (ED50=40.34 mg/kg, scPTZ test) demonstrated the highest potency. These compounds displayed considerably better safety profiles than clinically relevant antiepileptic drugs phenytoin, ethosuximide, or valproic acid. Several molecules showed antinociceptive and local anesthetic properties. The in vitro radioligand binding studies demonstrated that the influence on the sodium and calcium channels may be one of the essential mechanisms of action. Copyright © 2016. Published by Elsevier Ltd.

Cobalt(ll) Coordination Compounds of Ethyl 4-Methyl-5-Imidazolecarboxylate: Chemical and Biochemical Characterization on Photosynthesis and Seed Germination

OpenAIRE

King-Díaz, Beatriz; Montes-Ayala, Josefina; Escartín-Guzmán, Concepción; Castillo-Blum, Silvia E.; Iglesias-Prieto, Roberto; Lotina-Hennsen, Blas; Barba-Behrens, Norah

2005-01-01

In this work we present the synthesis, structural and spectroscopic characterization of Co2+ coordination compounds with ethyl 4-methyl-5-imidazolecarboxylate (emizco). The effects of emizco, the metal salts CoCl2.6H2O, CoBr2, Co(NO3)2.6H2O and their metal coordination compounds [Co(emizco)2Cl2], [Co(emizco)2 Br2].H2O, [Co(emizco)2 (H2O)2(NO2)2.2H2O were evaluated on photosynthesis in spinach chloroplasts. Seed germination and seedling growth of the monocotyledonous species Lolium multiflorum...

Potential neuroleptic agents. 4. Chemistry, behavioral pharmacology, and inhibition of [3H]spiperone binding of 3,5-disubstituted N-[(1-ethyl-2-pyrrolidinyl)methyl]-6-methoxysalicylamides.

Science.gov (United States)

de Paulis, T; Kumar, Y; Johansson, L; Rämsby, S; Hall, H; Sällemark, M; Angeby-Möller, K; Ogren, S O

1986-01-01

A series of 3,5-disubstituted N-[(1-ethyl-2-pyrrolidinyl) methyl]-6-methoxysalicylamides was synthesized, starting from the 2,6-dimethoxybenzoic acids, by boron tribromide demethylation of the corresponding 3,5-disubstituted 2,6-dimethoxybenzamides and separation of the two positional isomers. The correct structure assignments were based on selective decoupling studies on their 13C NMR spectra. The salicylamide derivatives were tested for antidopamine activity in vivo by their ability to inhibit the apomorphine syndrome in the rat and in vitro by their ability to displace [3H]spiperone from striatal preparations of the rat brain. The activity seems to reside exclusively in the S enantiomer. Several compounds were considerably more potent than haloperidol, particularly those having an ethyl group in the 3-position and a halogen atom in the 5-position of the aromatic ring. The corresponding 5-alkyl-3-halogen-substituted compounds were much less active. A low acute toxicity was found for the most potent compounds. Some of the salicylamides displayed a 10-20-fold separation between the dose which blocks apomorphine-induced hyperactivity and that which blocks apomorphine-induced stereotypy. One compound, S-(-)-3,5-dichloro-N-[(1-ethyl-2-pyrrolidinyl) methyl]-6-methoxysalicylamide (raclopride, FLA 870) (13) had a stereotypy--hyperactivity separation more than twice that of sulpiride while being 100 times more potent in blocking the apomorphine effects. On this basis, 13 was selected for clinical trials against schizophrenia.

Efficacy of scalp hair decontamination following exposure to vapours of sulphur mustard simulants 2-chloroethyl ethyl sulphide and methyl salicylate.

Science.gov (United States)

Spiandore, Marie; Piram, Anne; Lacoste, Alexandre; Prevost, Philippe; Maloni, Pascal; Torre, Franck; Asia, Laurence; Josse, Denis; Doumenq, Pierre

2017-04-01

Chemical warfare agents are an actual threat and victims' decontamination is a main concern when mass exposure occurs. Skin decontamination with current protocols has been widely documented, as well as surface decontamination. However, considering hair ability to trap chemicals in vapour phase, we investigated hair decontamination after exposure to sulphur mustard simulants methyl salicylate and 2-chloroethyl ethyl sulphide. Four decontamination protocols were tested on hair, combining showering and emergency decontamination (use of Fuller's earth or Reactive Skin Decontamination Lotion RSDL ® ). Both simulants were recovered from hair after treatment, but contents were significantly reduced (42-85% content allowance). Showering alone was the least efficient protocol. Concerning 2-chloroethyl ethyl sulphide, protocols did not display significant differences in decontamination efficacy. For MeS, use of emergency decontaminants significantly increased showering efficacy (10-20% rise), underlining their usefulness before thorough decontamination. Our results highlighted the need to extensively decontaminate hair after chemical exposure. Residual amounts after decontamination are challenging, as their release from hair could lead to health issues. Copyright © 2016. Published by Elsevier B.V.

Incineration of oxygenated volatile organic compounds. Experimental study and kinetic modeling of the oxidation of methyl ethyl ketone, ethyl acetate and butan-2-ol in methane flames; Incineration de composes organiques volatils oxygenes. Etude experimentale et modelisation cinetique de l'oxydation de la methyl ethyl cetone, de l'acetate d'ethyle et du butan-2-ol dans des flammes de methane

Energy Technology Data Exchange (ETDEWEB)

Decottignies, V

2000-12-01

This work deals with the low pressure (0.05 atm) degradation of three volatile organic compounds (VOCs): methyl-ethyl-ketone, ethyl acetate and butan-2-ol, in premixed stoichiometric laminar methane flames seeded with 1 to 3% of each VOC. Molar fraction profiles of species have been obtained using microprobe sampling coupled with a gas chromatography and a mass spectroscopy analysis. Temperature profiles have been obtained using the covered thermocouple technique in the presence of the microprobe. The addition of a VOC in the initial reagents mixture leads to an increase of the quantity of intermediate hydrocarbon compounds and in particular of some soot precursor species. The degradation of VOCs leads to the formation of oxygenated intermediates like methanol, dimethyl-ether, acetaldehyde, propanal, acetone and vinyl acetate, the type of VOC having an effect on the quantities produced. The degradation of a VOC can lead to the formation of more toxic or polluting compounds (methyl vinyl ketone, acetic acid and acrolein) than the VOC itself. In the conditions of the study, the intermediate compounds are totally destructed inside the reactional area of the flame front and are no more present in the burnt gases. Sub-mechanisms of VOC oxidation have been developed using experimental observations and the most recent recommendations of the literature. These sub-mechanisms comprise 49 species involved in 241 elementary reactions. Their validation has been performed by comparing the experiment with the kinetic modeling on the molar fraction profiles of the detected species. Experimental data are well reproduced by the model for most species. The addition of a VOC inside the initial reagents mixture creates an important reactivity increase, in particular in the case of butan-2-ol seeded flames. The analysis of reactional ways has permitted to draw out the main reactions responsible for the degradation of the 3 VOCs and the ways of formation and consumption of the

Morphology and performance of poly(2-methoxy-5-(20-ethyl-hexyloxy)-p-phenylenevinylene) (MEH-PPV) : (6,6)-phenyl-C61-butyric acid methyl ester (PCBM) based polymer solar cells

NARCIS (Netherlands)

Liu, L.J.; Bavel, van S.S.; Wen, S.P.; Yang, X.N.; Loos, J.

2013-01-01

Polymer solar cells were fabricated based on composite films of poly(2-methoxy-5-(2-ethyl-hexyloxy)-1,4-phenylenevinylene) (MEH-PPV):fullerene derivative (6,6)-phenyl-C61-butyric acid methyl ester (PCBM) with weight blend ratio of 1:3, 1:4 and 1:5, spin-coated from chloroform (CF), chlorobenzene

Two Zn and Hg bromide salts based on 1-ethyl-3-methyl imidazolium ionic liquid: Ionothermal synthesis, structures and supramolecular organization

Directory of Open Access Journals (Sweden)

Xiu-Cheng Zhang

2012-12-01

Full Text Available Two Zn(II and Hg(II bromide salts, [EMI]2[ZnBr4] (1 and [EMI][HgBr3] (2, have been synthesized under ionothermal conditions using 1-ethyl-3-methyl imidazolium bromide ([EMI]Br as solvents. 1 consists of tetrahedral anion [ZnBr4]2− and 2 consists of 1D double chain locating in the cavities surrounded by [EMI]+ cations. Both compounds exhibit 3D supramolecular architectures organized by the C-H•••Br hydrogen bondings and alkyl-alkyl interactions.DOI: http://dx.doi.org/10.4314/bcse.v26i3.9

Quantification of four major metabolites of embryotoxic N-methyl- and N-ethyl-2-pyrrolidone in human urine by cooled-injection gas chromatography and isotope dilution mass spectrometry.

Science.gov (United States)

Schindler, Birgit K; Koslitz, Stephan; Meier, Swetlana; Belov, Vladimir N; Koch, Holger M; Weiss, Tobias; Brüning, Thomas; Käfferlein, Heiko U

2012-04-17

N-Methyl- and N-ethyl-2-pyrollidone (NMP and NEP) are frequently used industrial solvents and were shown to be embryotoxic in animal experiments. We developed a sensitive, specific, and robust analytical method based on cooled-injection (CIS) gas chromatography and isotope dilution mass spectrometry to analyze 5-hydroxy-N-ethyl-2-pyrrolidone (5-HNEP) and 2-hydroxy-N-ethylsuccinimide (2-HESI), two newly identified presumed metabolites of NEP, and their corresponding methyl counterparts (5-HNMP, 2-HMSI) in human urine. The urine was spiked with deuterium-labeled analogues of these metabolites. The analytes were separated from urinary matrix by solid-phase extraction and silylated prior to quantification. Validation of this method was carried out by using both, spiked pooled urine samples and urine samples from 56 individuals of the general population with no known occupational exposure to NMP and NEP. Interday and intraday imprecision was better than 8% for all metabolites, while the limits of detection were between 5 and 20 μg/L depending on the analyte. The high sensitivity of the method enables us to quantify NMP and NEP metabolites at current environmental exposures by human biomonitoring.

Synthesis and characterization of Ni0.7Zn0.3Fe2O4 ferrospinel: performance evaluation for methyl and ethyl esterification

International Nuclear Information System (INIS)

Mapossa, A.B.; Dantas, J.; Diniz, V.C.S.; Costa, A.C.F.M.; Silva, M.R.; Kiminami, R.H.G.A.

2017-01-01

Ni 0.7 Zn 0.3 Fe 2 O 4 ferrospinel was synthesized by combustion and its catalytic performance in methyl and ethyl esterification of the soybean oil was investigated. The samples were characterized by X-ray diffraction, Rietveld refinement analysis, energy dispersive X-ray fluorescence spectroscopy, Fourier transform infrared spectroscopy, textural analysis, scanning electron microscopy, density by picnometry, particle size analysis, thermogravimetric analysis, magnetic measurements, and catalytic tests. The synthesis was efficient resulting in a ferrospinel with single phase Ni 0.7 Zn 0.3 Fe 2 O 4 with crystallite size of 20 nm, high surface area (86 m 2 /g) and saturation magnetization of 18 emu/g. The ferrospinel had promising catalytic activity in both reaction conditions studied, being more active in the conversion of soybean oil to biodiesel in methyl esterification with an average conversion of 93.9±2.8%. (author)

Synthesis and crystal structures of 2-methyl-4-aryl-5-oxo-5H-indeno [1,2-b] pyridine carboxylate derivatives

DEFF Research Database (Denmark)

Pandian, Ramesh; Naushad, Edayadulla; Vijayakumar, Vinodhkumar

2014-01-01

pyridine derivatives through oxidation. Consequently, the interest in this aromatization reaction, investigation of a wide range of 1, 4-DHPs continues to attract the attention of researchers. Herein, we report the preparation of pyridine derivatives and the crystal structures determined by X......-ray crystallographic methods.Results: The crystal structures and conformational studies of two organic compounds, namely ethyl 2-methyl-4-phenyl-5-oxo-5H-indeno [1,2-b] pyridine-3-carboxylate (I) and ethyl 2-methyl-4-(4 chlorophenyl)-5-oxo-5H-indeno [1,2-b] pyridine-3-carboxylate (II) are reported. The terminal ethyl......) dimer running along 011 direction.Conclusion: The crystal structures ethyl 2-methyl-4-phenyl-5-oxo-5H-indeno [1,2-b] pyridine-3-carboxylate and ethyl 2-methyl-4-(4 chlorophenyl)-5-oxo-5H-indeno [1,2-b] pyridine-3-carboxylate have been investigated in detail. The terminal ethyl group of compound I...

A silicone rubber based composites using n-octadecane/poly (styrene-methyl methacrylate microcapsules as energy storage particle

Directory of Open Access Journals (Sweden)

W.L. Wu

Full Text Available A phase-change energy-storage material, silicone rubber (SR coated n-octadecane/poly (styrene-methyl methacrylate (SR/OD/P(St-MMA microcapsule composites, was prepared by mixing SR and OD/P(St-MMA microcapsules. The microcapsule content and silicone rubber coated method were investigated. The morphology and thermal properties of the composites were characterized by scanning electron microscopy (SEM, thermogravimetric analysis (TG, differential scanning calorimetry (DSC and heat storage properties. The results showed that the thermal and mechanical properties of SR/OD/P(St-MMA composites were excellent when the microcapsules were coated with room temperature vulcanized silicone rubber (RTVSR, of which content was 2 phr (per hundred rubber. The enthalpy value of the composites was 67.6 J g−1 and the composites were found to have good energy storage function. Keywords: n-Octadecane, Silicone rubber, Microcapsule, Energy-storage, Composites

Incineration of oxygenated volatile organic compounds. Experimental study and kinetic modeling of the oxidation of methyl ethyl ketone, ethyl acetate and butan-2-ol in methane flames; Incineration de composes organiques volatils oxygenes. Etude experimentale et modelisation cinetique de l'oxydation de la methyl ethyl cetone, de l'acetate d'ethyle et du butan-2-ol dans des flammes de methane

Energy Technology Data Exchange (ETDEWEB)

Decottignies, V.

2000-12-01

This work deals with the low pressure (0.05 atm) degradation of three volatile organic compounds (VOCs): methyl-ethyl-ketone, ethyl acetate and butan-2-ol, in premixed stoichiometric laminar methane flames seeded with 1 to 3% of each VOC. Molar fraction profiles of species have been obtained using microprobe sampling coupled with a gas chromatography and a mass spectroscopy analysis. Temperature profiles have been obtained using the covered thermocouple technique in the presence of the microprobe. The addition of a VOC in the initial reagents mixture leads to an increase of the quantity of intermediate hydrocarbon compounds and in particular of some soot precursor species. The degradation of VOCs leads to the formation of oxygenated intermediates like methanol, dimethyl-ether, acetaldehyde, propanal, acetone and vinyl acetate, the type of VOC having an effect on the quantities produced. The degradation of a VOC can lead to the formation of more toxic or polluting compounds (methyl vinyl ketone, acetic acid and acrolein) than the VOC itself. In the conditions of the study, the intermediate compounds are totally destructed inside the reactional area of the flame front and are no more present in the burnt gases. Sub-mechanisms of VOC oxidation have been developed using experimental observations and the most recent recommendations of the literature. These sub-mechanisms comprise 49 species involved in 241 elementary reactions. Their validation has been performed by comparing the experiment with the kinetic modeling on the molar fraction profiles of the detected species. Experimental data are well reproduced by the model for most species. The addition of a VOC inside the initial reagents mixture creates an important reactivity increase, in particular in the case of butan-2-ol seeded flames. The analysis of reactional ways has permitted to draw out the main reactions responsible for the degradation of the 3 VOCs and the ways of formation and consumption of the

A silicone rubber based composites using n-octadecane/poly (styrene-methyl methacrylate) microcapsules as energy storage particle

Science.gov (United States)

Wu, W. L.; Chen, Z.

A phase-change energy-storage material, silicone rubber (SR) coated n-octadecane/poly (styrene-methyl methacrylate) (SR/OD/P(St-MMA)) microcapsule composites, was prepared by mixing SR and OD/P(St-MMA) microcapsules. The microcapsule content and silicone rubber coated method were investigated. The morphology and thermal properties of the composites were characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TG), differential scanning calorimetry (DSC) and heat storage properties. The results showed that the thermal and mechanical properties of SR/OD/P(St-MMA) composites were excellent when the microcapsules were coated with room temperature vulcanized silicone rubber (RTVSR), of which content was 2 phr (per hundred rubber). The enthalpy value of the composites was 67.6 J g-1 and the composites were found to have good energy storage function.

Inhalation developmental toxicology studies: Teratology study of methyl ethyl ketone in mice: Final report

Energy Technology Data Exchange (ETDEWEB)

Mast, T.J.; Dill, J.A.; Evanoff, J.J.; Rommereim, R.L.; Weigel, R.J.; Westerberg, R.B.

1989-02-01

Methyl ethyl ketone (MEK) is a widely used industrial solvent which results in considerable human exposure. In order to assess the potential for MEK to cause developmental toxicity in rodents, four groups of Swiss (CD-1) mice were exposed to 0, 400, 1000 or 3000 ppM MEK vapors, 7 h/day, 7 dy/wk. Ten virgin females and approx.30 plug-positive females per group were exposed concurrently for 10 consecutive days (6--15 dg for mated mice). Body weights were obtained throughout the study period, and uterine and fetal body weights were obtained at sacrifice on 18 dg. Uterine implants were enumerated and their status recorded. Live fetuses were sexed and examined for gross, visceral, skeletal, and soft-tissue craniofacial defects. Exposure of pregnant mice to these concentrations of MEK did not result in apparent maternal toxicity, although there was a slight, treatment-correlated increase in liver to body weight ratios which was significant for the 3000-ppM group. Mild developmental toxicity was evident at 3000-ppM as a reduction in mean fetal body weight. This reduction was statistically significant for the males only, although the relative decrease in mean fetal body weight was the same for both sexes. 17 refs., 4 figs., 10 tabs.

Inhalation developmental toxicology studies: Teratology study of methyl ethyl ketone in mice: Final report

International Nuclear Information System (INIS)

Mast, T.J.; Dill, J.A.; Evanoff, J.J.; Rommereim, R.L.; Weigel, R.J.; Westerberg, R.B.

1989-02-01

Methyl ethyl ketone (MEK) is a widely used industrial solvent which results in considerable human exposure. In order to assess the potential for MEK to cause developmental toxicity in rodents, four groups of Swiss (CD-1) mice were exposed to 0, 400, 1000 or 3000 ppM MEK vapors, 7 h/day, 7 dy/wk. Ten virgin females and ∼30 plug-positive females per group were exposed concurrently for 10 consecutive days (6--15 dg for mated mice). Body weights were obtained throughout the study period, and uterine and fetal body weights were obtained at sacrifice on 18 dg. Uterine implants were enumerated and their status recorded. Live fetuses were sexed and examined for gross, visceral, skeletal, and soft-tissue craniofacial defects. Exposure of pregnant mice to these concentrations of MEK did not result in apparent maternal toxicity, although there was a slight, treatment-correlated increase in liver to body weight ratios which was significant for the 3000-ppM group. Mild developmental toxicity was evident at 3000-ppM as a reduction in mean fetal body weight. This reduction was statistically significant for the males only, although the relative decrease in mean fetal body weight was the same for both sexes. 17 refs., 4 figs., 10 tabs

Configuration of a pulse radiolysis system for the study of gas-phase reactions and kinetic investigations of the reactions of hydroxyl radicals with methyl and ethyl radicals

International Nuclear Information System (INIS)

Fagerstroem, K.

1993-01-01

The work that is presented in this thesis deals with the assembling and testing of a pulse radiolysis system for kinetic studies of gas-phase reactions as well as with the kinetics of the gas-phase reactions of hydroxyl radicals with methyl and ethyl radicals. These radicals are very important as these are formed at an early stage in hydrocarbon combustion processes. The two studied reactions are key reactions in those processes. (6 refs., 4 figs., 2 tabs.)

Application of La-ZSM-5 Coated Silicon Carbide Foam Catalyst for Toluene Methylation with Methanol

Directory of Open Access Journals (Sweden)

Debarpita Ghosal

2015-07-01

Full Text Available The performance of toluene methylation reaction was studied on H-ZSM-5 catalyst modified with La, Ce and Nb at different percentage loading. It was found that 10% metal loading produced the best performance in the reaction in terms of toluene conversion. The catalyst was coated on silicon carbide foam support which showed better conversion than the pelleted catalyst. Again, among the treated and untreated H-ZSM-5, the La-ZSM-5 catalyst is chosen for the reaction for its highest selectivity towards xylene, the main product. All catalysts were characterized in terms of surface properties, SEM, XRD and NH3-TPD. Kinetic study was done on La-ZSM-5 catalyst with 10% loading. In this kineticstudy, Langmuir Hinshelwood kinetic model with surface reaction as rate controlling step was selected as the rate equation. The activation energy was found to be 47 kJ/mol. © 2015 BCREC UNDIP. All rights reserved. Received: 9th December 2014; Revised: 27th April 2015; Accepted: 29th April 2015  How to Cite: Ghosal, D., Basu, J.K., Sengupta, S. (2015. Application of La-ZSM-5 Coated Silicon Carbide Foam Catalyst for Toluene Methylation with Methanol. Bulletin of Chemical Reaction Engineering & Catalysis, 10 (2: 201-209. (doi:10.9767/bcrec.10.2.7872.201-209 Permalink/DOI: http://dx.doi.org/10.9767/bcrec.10.2.7872.201-209  

Potassium methyl siliconate-treated pulp fibers and their effects on wood plastic composites: Water sorption and dimensional stability

Science.gov (United States)

Cheng Piao; Zhiyong Cai; Nicole M. Stark; Charles J. Monlezun

2013-01-01

Potassium methyl siliconate (PMS) was investigated as a new nano modifier of wood fiber and wood flour to improve the compatibility between the fiber/flour and the plastic matrix in fiber reinforced plastic composites. Before injection molding, bleached and brown pulp fibers and mixed species wood flour were pretreated in PMS solutions. The morphology of the treated...

Convenient synthesis of 6-nor-9,10-dihydrolysergic acid methyl ester.

Science.gov (United States)

Crider, A M; Grubb, R; Bachmann, K A; Rawat, A K

1981-12-01

6-Nor-9,10-dihydrolysergic acid methyl ester (IV) was prepared by demethylation of 9,10-dihydrolysergic acid methyl ester (II) with 2,2,2-trichloroethyl chloroformate, followed by reduction of the intermediate carbamate (III) with zinc in acetic acid. The 6-ethyl-V and 6-n-propyl-VI derivatives were prepared by alkylation of IV with the appropriate halide. All of the ergoline derivatives were evaluated for stereotyped behavior in rats, with 6-nor-6-ethyl-9,10-dihydrolysergic acid methyl ester (V) being active but much less potent than apomorphine. Compound VI was evaluated for its effect on blood pressure; at a dose of 30 mg/kg ip, it significantly lowered, diastolic pressure in normotensive rats.

Adsorptive binding of methanol and ethanol on the oxides of silicon, titanium, zirconium, and thorium

Energy Technology Data Exchange (ETDEWEB)

Huettig, G F; Pietzka, G

1948-01-01

The authors plot adsorption isotherms for methyl alcohol, ethyl alcohol, and CCl/sub 4/ on SiO/sub 2/, TeO/sub 2/, ZrO/sub 2/, and ThO/sub 2/. The results seem to show that for a given adsorbent the volume of gas required to form a monolayer is independent of the absorbent temperature and that a greater volume of methyl alcohol than of ethyl alcohol is required to form a monolayer. The ratio of the specific rate of absorption to the specific rate of desorption is larger for ethyl alcohol than for methyl alcohol. The value of this ratio decreases with increase in temperature for a given adsorbate and a given adsorbent.

[Study on chemical constituents from ethyl acetate extract of Myricaria bracteata].

Science.gov (United States)

Zhang, Ying; Yuan, Yi; Cui, Baosong; Li, Shuai

2011-04-01

To study the chemical constituents from the ethyl acetate extract of Myricaria bracteata. The chemical constituents were isolated and purified by chromatographic techniques, and their structures were identified by physical characters and spectroscopic analysis. Sixteen compounds were isolated from the ethyl acetate portion of the 95% ethanolic extract of Myricaria bracteata, and identified as myricarin (1), myricarin B (2), 3alpha-hydroxytaraxer-14-en-28-oic acid (3), myricadiol (4), trans-ferulic acid 22-hydroxydocosanoic acid ester (5), docosyl-3, 4-dihydroxy-trans-cinnamate (6), dillenetin (7), 3, 5, 4'-trihydroxy-7-methoxyflavone (8), 3, 5, 4'-trihydroxy-7, 3'-dimethoxyflavone (9), methyl 3, 5-dihydroxy-4-methoxybenzoate (10), 3-hydroxy-4-methoxy cinnamic acid (11), sinapaldehyde (12), vanillin (13), syringaldehyde (14), 3, 3', 4'-trimethoxyellagic acid (15), methyl p-hyroxybenzoate (16). Compounds 5, 6, 12-16 were isolated from the genus Myricaria for the fist time, all of the compounds were isolated from this plant for the fist time, except for 8 and 9.

[COMPARATIVE SENSITIVITY OF CHOLINESTERASES IN VERTEBRATES AND INVERTEBRATES TO HIGHLY SPECIFIC ORGANOPHOSPHORUS INHIBITORS DIISOPROPYL FLUOROPHOSPHATE (DFP) AND (2-ETHOXYMETHYL PHOSPHORYL THIOETHYL) ETHYL (METHYL) SULPHONIUM SULPHOMETHYLAT (GD-42)].

Science.gov (United States)

Basova, N E; Kormilitsyn, B N; Perchenok, A Yu; Rozengart, E V; Saakov, V S; Suvorov, A A

2015-01-01

The review presents data on comparative reactivity of 68 cholinesterase preparation from various organs and tissues in a number of vertebrates and invertebrates based on sensitivity to two highly specific and most studied organophosphorus inhibitors--diisopropyl fluorophosphates (DFP) and (2-ethoxymethyl phosphoryl thioethyl) ethyl (methyl) sulphonium sulphomethylat (GD-42). Analysis of these data suggests a great diversity in enzymologic characteristics of cholinesterase preparation in representatives of vertebrates and invertebrates, this variety observed even for closely related enzymes in animals of almost the same level of development.

New Measurements of Methyl Ethyl Ketone (MEK) Photolysis Rates and Their Relevance to Global Oxidative Capacity

Science.gov (United States)

Brewer, J.; Ravishankara, A. R.; Mellouki, A.; Fischer, E. V.; Kukui, A.; Véronique, D.; Ait-helal, W.; Leglise, J.; Ren, Y.

2017-12-01

Methyl ethyl ketone (MEK) is one of the most abundant ketones in the atmosphere. MEK can be emitted directly into the atmosphere from both anthropogenic and natural sources, and it is also formed during the gas-phase oxidation of volatile organic compounds (VOCs). MEK is lost via reaction with OH, photolysis and deposition to the surface. Similar to the other atmospheric ketones, the photolysis of MEK may represent a source of HOx (OH + HO2) radicals in the upper troposphere. The degradation of MEK also leads to the atmospheric formation of acetaldehyde and formaldehyde. This work presents a new analysis of the temperature dependence of MEK photolysis cross-sections and a quantification of MEK photolysis rates under surface pressures using the CNRS HELIOS outdoor atmospheric chamber (Chambre de simulation atmosphérique à irradiation naturelle d'Orléans; http://www.era-orleans.org/ERA-TOOLS/helios-project.html). Additionally, we use the GEOS-Chem 3-D CTM (version 10-01, www.geos-chem.org) to investigate the impact of these newly measured rates and cross-sections on the global distribution and seasonality of MEK, as well as its importance to the tropospheric oxidative capacity.

Synthesis and Antimicrobial Activity of Novel 3-[1-(3-nitrophenyl)-ethyl

African Journals Online (AJOL)

Syntheses of novel 3-[1-(3-nitrophenyl)-ethyl]-1-(indole-1-yl) substituted aryl/alkyl phosphinoyl/thiophosphinoyl/selenophosphinoyl-1H-indole derivatives were accomplished in two steps. The synthetic route involves the cyclisation of equimolar quantities of 3-[1H-3-indolyl(3-nitrophenyl)methyl]-1H-indole with dichlorophenyl ...

Dimensional stability of wood-plastic composites reinforced with potassium methyl siliconate modified fiber and sawdust made from beetle-killed trees

Science.gov (United States)

Cheng Piao; Zhiyong Cai; Nicole M. Stark; Charles J. Montezun

2014-01-01

Wood fromtwovarieties of beetle-killed trees was used to fabricate wood–plastic composites. Loblolly pine and lodgepole pine beetle-killed trees were defibrated mechanically and thermomechanically, respectively, into fiber. Fiber and sawdust produced from the trees were modified with potassium methyl siliconate (PMS) and injection-molded into fiber/sawdust reinforced...

Combustion by synthesis in pilot scale of nanocatalyst Ni_0_,_5Zn_0_,_5Fe_2O_4 and the performance in methyl and ethyl esterification to obtaining biodiesel

International Nuclear Information System (INIS)

Moura, T.F.B.; Barros, A.B.S.; Dantas, J.; Pereira, K.R.O.; Vasconcelos, E.V.; Costa, A.C.F.M.

2016-01-01

To produce biodiesel from the use of catalysts is necessary because help in getting better reaction yields and currently magnetic materials has gained prominence for this application. This study aimed to prepare the nanocatalyst Ni_0_,_5Zn_0_,_5Fe_2O_4 in laboratory scale, to evaluate their performance in methyl AND ethyl esterification using acidified soybean oil as raw material. The samples were synthesized by reaction in a combustion reactor with a production capacity of 200g / batch and characterized by XRD, TG and EDX. The catalytic tests took place at a temperature of 180 ° C / 1h, molar ratio 1:12, 2% nanocatalyst and analyzed by gas chromatography. Samples showed the major phase of the inverse spinel with an average crystallite size of 20.25 nm and traces of segregated phases of Fe_2O_3 and ZnO. The values of the detected oxides were 68.01% for Fe2O3, 16.57% for NiO and 15.28% for ZnO, values that are close to the calculated theoretical. The sample showed total mass loss equal to 6.5%, demonstrating its excellent thermal stability. The biodiesel conversion results were 84.11 and 73.74% for methyl ethyl route, respectively. Therefore, the synthesized material has catalytic potential in the tested reaction and could be a promising material for both assessed routes. (author)

Synthesis and in vivo evaluation of [O-methyl-11C](2R,4R)-4-hydroxy-2-[2-[2-[2-(3-methoxy)phenyl]ethyl]phenoxy] ethyl-1-methylpyrrolidine as a 5-HT2A receptor PET ligand

International Nuclear Information System (INIS)

Kumar, J.S. Dileep; Prabhakaran, Jaya; Erlandsson, Kjell; Majo, Vattoly J.; Simpson, Norman R.; Pratap, Mali; Heertum, Ronald L. van; Mann, J. John; Parsey, Ramin V.

2006-01-01

The serotonin 2A (5-HT 2A ) receptor is implicated in the pathophysiology of schizophrenia and mood disorders, and in vivo studies of this receptor would be of value in studying the pathophysiology of these disorders and in measuring the relationship of clinical response to receptor occupancy for 5-HT 2A antagonists such as atypical antipsychotics. Therefore, (2R,4R)-4-hydroxy-2-[2-[2-[2-(3-methoxy)-phenyl]ethyl] phenoxy]ethyl-1-methylpyrrolidine (MPM) (13), a selective and high-affinity (K i =0.79 nM) 5HT 2A antagonist, has been radiolabeled with carbon-11 by O-methylation of the corresponding desmethyl analogue (2R,4R)-4-hydroxy-2-[2-[2-[2-(3-hydroxy)phenyl]ethyl]phenoxy] ethyl-1-methylpyrrolidine (12) with [ 11 C]methyltriflate in order to determine the suitability of [ 11 C]MPM to quantify 5-HT 2A in living brain using PET. Desmethyl-MPM 12 and standard MPM were prepared, starting from 3-hydroxymethylphenol (2), in excellent yield. The yield obtained for radiolabeling was 40±5% (EOB), and the total synthesis time was 30 min at EOS. PET studies with [ 11 C]MPM in baboon showed a distribution in the brain consistent with the known distribution of 5-HT 2A receptors. The time-activity curves for the high-binding regions peaked at ∼45 min after injection. Blocking studies with M100907 demonstrated not only 38-57% blocking of tracer binding in brain regions known to have 5-HT 2A receptors but also 38% blocking in cerebellum, which has a low 5-HT 2A receptor concentration. Although [ 11 C]MPM exhibits appropriate kinetics in baboon for imaging 5-HT 2A receptors, its specific binding in cerebellum and higher proportion of nonspecific binding limit its usefulness for the in vivo quantification of 5-HT 2A receptors with PET

Crystal structure of the tetragonal polymorph of bis(1-ethyl-3-methylimidazolium tetrabromidocadmate

Directory of Open Access Journals (Sweden)

Tamara Đorđević

2016-07-01

Full Text Available Both unique Cd atoms in the tetragonal polymorph of bis(1-ethyl-3-methylimidazolium tetrabromidocadmate, (C6H11N22[CdBr4], occupy special positions (site symmetry -4. The crystal structure consists of isolated tetrahedral [CdBr4]2− anions which are surrounded by 1-ethyl-3-methylimidazolium cations. The methyl and ethyl side chains of the cations show positional disorder in a 0.590 (11:0.410 (11 ratio. In the crystal, (C6H11N2+ cations display three weak C—H...Br hydrogen-bond interactions through the imidazolium ring H atoms with the Br− ligands of the surrounding complex anions. The alkyl groups of the side chains are not involved in hydrogen bonding.

Simultaneous Determination of Salicylic Acid, Jasmonic Acid, Methyl Salicylate, and Methyl Jasmonate from Ulmus pumila Leaves by GC-MS

OpenAIRE

Huang, Zhi-hong; Wang, Zhi-li; Shi, Bao-lin; Wei, Dong; Chen, Jian-xin; Wang, Su-li; Gao, Bao-jia

2015-01-01

Salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate are important phytohormones and defensive signaling compounds, so it is of great importance to determine their levels rapidly and accurately. The study uses Ulmus pumila leaves infected by Tetraneura akinire Sasaki at different stages as materials; after extraction with 80% methanol and ethyl acetate and purification with primary secondary amine (PSA) and graphitized carbon blacks (GCB), the contents of signal compounds sa...

Anti-inflammatory activity of methyl palmitate and ethyl palmitate in different experimental rat models

Energy Technology Data Exchange (ETDEWEB)

Saeed, Noha M. [Department of Pharmacology and Toxicology, Faculty of Pharmacy, Egyptian Russian University, Cairo (Egypt); El-Demerdash, Ebtehal [Department of Pharmacology and Toxicology, Faculty of Pharmacy, Ain Shams University, Cairo (Egypt); Abdel-Rahman, Hanaa M. [Department of Pharmacology and Toxicology, Faculty of Pharmacy, Egyptian Russian University, Cairo (Egypt); Algandaby, Mardi M. [Department of Biology (Botany), Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia); Al-Abbasi, Fahad A. [Department of Biochemistry, Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia); Abdel-Naim, Ashraf B., E-mail: abnaim@pharma.asu.edu.eg [Department of Pharmacology and Toxicology, Faculty of Pharmacy, Ain Shams University, Cairo (Egypt)

2012-10-01

Methyl palmitate (MP) and ethyl palmitate (EP) are naturally occurring fatty acid esters reported as inflammatory cell inhibitors. In the current study, the potential anti-inflammatory activity of MP and EP was evaluated in different experimental rat models. Results showed that MP and EP caused reduction of carrageenan-induced rat paw edema in addition to diminishing prostaglandin E2 (PGE2) level in the inflammatory exudates. In lipopolysaccharide (LPS)-induced endotoxemia in rats, MP and EP reduced plasma levels of tumor necrosis factor-α (TNF-α) and interleukin-6 (IL-6). MP and EP decreased NF-κB expression in liver and lung tissues and ameliorated histopathological changes caused by LPS. Topical application of MP and EP reduced ear edema induced by croton oil in rats. In the same animal model, MP and EP reduced neutrophil infiltration, as indicated by decreased myeloperoxidase (MPO) activity. In conclusion, this study demonstrates the effectiveness of MP and EP in combating inflammation in several experimental models. -- Highlights: ► Efficacy of MP and EP in combating inflammation was displayed in several models. ► MP and EP reduced carrageenan-induced rat paw edema and prostaglandin E2 level. ► MP and EP decreased TNF-α and IL-6 levels in experimental endotoxemia. ► MP and EP reduced NF-κB expression and histological changes in rat liver and lung. ► MP and EP reduced croton oil-induced ear edema and neutrophil infiltration.

Determination coefficient distribution rhenium and tungsten using method extraction with solvent methyl ethyl ketone

International Nuclear Information System (INIS)

Riftanio Natapratama Hidayat; Maria Christina Prihatiningsih; Duyeh Setiawan

2015-01-01

Determination of the distribution coefficient (K d ) of the rhenium and tungsten conducted for the purpose of knowing the value of K d of the two elements. K d value determination is applied to the process of separation rhenium-188 from target of tungsten-188 for the purposes purification of radioisotopes that are made to meet the radionuclide and radiochemical purity. The K d value determination using solvent extraction with methyl ethyl ketone (MEK). Prior to the determination of K d values, determined beforehand the optimum conditions of extraction process based on the effect of agitation time, the volume of MEK, and the pH of the solution. Confirmation the results of the extraction was conducted using UV-Vis spectrophotometer with a complexing KSCN under acidic conditions and reductant SnCl 2 . The results showed that the optimum condition extraction process to feed each of 10 ppm is when the agitation for 10 minutes, the volume of MEK in 20 ml, and the pH below 5. Obtained the maximum recovery of rhenium are drawn to the organic phase as much as 9.545 ppm. However, the condition of the extraction process does not affect the migration of tungsten to the organic phase. Then the maximum K d values obtained at 2.7566 rhenium and tungsten maximum K d is 0.0873. Optimum conditions of extraction process can be further tested on radioactive rhenium and tungsten as an alternative to the separation of radioisotopes. (author)

Thermal explosion analysis of methyl ethyl ketone peroxide by non-isothermal and isothermal calorimetric applications

International Nuclear Information System (INIS)

Chi, Jen-Hao; Wu, Sheng-Hung; Shu, Chi-Min

2009-01-01

In the past, process incidents attributed to organic peroxides (OPs) that involved near misses, over-pressures, runaway reactions, and thermal explosions occurred because of poor training, human error, incorrect kinetic assumptions, insufficient change management, and inadequate chemical knowledge in the manufacturing process. Calorimetric applications were employed broadly to test organic peroxides on a small-scale because of their thermal hazards, such as exothermic behavior and self-accelerating decomposition in the laboratory. In essence, methyl ethyl ketone peroxide (MEKPO) is highly reactive and exothermically unstable. In recent years, it has undergone many thermal explosions and runaway reaction incidents in the manufacturing process. Differential scanning calorimetry (DSC), vent sizing package 2 (VSP2), and thermal activity monitor (TAM) were employed to analyze thermokinetic parameters and safety index. The intent of the analyses was to facilitate the use of various auto-alarm equipments to detect over-pressure, over-temperature, and hazardous materials leaks for a wide spectrum of operations. Results indicated that MEKPO decomposition is detected at low temperatures (30-40 deg. C), and the rate of decomposition was shown to exponentially increase with temperature and pressure. Determining time to maximum rate (TMR), self-accelerating decomposition temperature (SADT), maximum temperature (T max ), exothermic onset temperature (T 0 ), and heat of decomposition (ΔH d ) was essential for identifying early-stage runaway reactions effectively for industries.

Enzymatic production of biodiesel from microalgal oil using ethyl acetate as an acyl acceptor.

Science.gov (United States)

Alavijeh, Razieh Shafiee; Tabandeh, Fatemeh; Tavakoli, Omid; Karkhane, Aliasghar; Shariati, Parvin

2015-01-01

Microalgae have become an important source of biomass for biodiesel production. In enzymatic transesterification reaction, the enzyme activity is decreased in presence of alcohols. The use of different acyl acceptors such as methyl/ethyl acetate is suggested as an alternative and effective way to overcome this problem. In this study, ethyl acetate was used for the first time in the enzymatic production of biodiesel by using microalga, Chlorella vulgaris, as a triglyceride source. Enzymatic conversion of such fatty acids to biodiesel was catalyzed by Novozym 435 as an efficient immobilized lipase which is extensively used in biodiesel production. The best conversion yield of 66.71% was obtained at the ethyl acetate to oil molar ratio of 13:1 and Novozym 435 concentration of 40%, based on the amount of oil, and a time period of 72 h at 40℃. The results showed that ethyl acetate have no adverse effect on lipase activity and the biodiesel amount was not decreased even after seven transesterification cycles, so ethyl acetate has a great potential to be substituted for short-chain alcohols in transesterification reaction.

Synthesis and in vivo evaluation of [O-methyl-{sup 11}C](2R,4R)-4-hydroxy-2-[2-[2-[2-(3-methoxy)phenyl]ethyl]phenoxy] ethyl-1-methylpyrrolidine as a 5-HT{sub 2A} receptor PET ligand

Energy Technology Data Exchange (ETDEWEB)

Kumar, J.S. Dileep [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Div. of Brain Imaging, Dept. of Neuroscience, New York State Psychiatric Institute, New York, NY 10032 (United States)]. E-mail: dk2038@columbia.edu; Prabhakaran, Jaya [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States); Erlandsson, Kjell [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Dept. of Radiology, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States); Majo, Vattoly J. [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States); Simpson, Norman R. [Dept. of Radiology, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States); Pratap, Mali [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Div. of Brain Imaging, Dept. of Neuroscience, New York State Psychiatric Institute, New York, NY 10032 (United States); Heertum, Ronald L. van [Dept. of Radiology, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States); Mann, J. John [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Dept. of Radiology, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Div. of Brain Imaging, Dept. of Neuroscience, New York State Psychiatric Institute, New York, NY 10032 (United States); Parsey, Ramin V. [Dept. of Psychiatry, College of Physicians and Surgeons, Columbia University, New York, NY 10032 (United States)]|[Div. of Brain Imaging, Dept. of Neuroscience, New York State Psychiatric Institute, New York, NY 10032 (United States)

2006-05-15

The serotonin{sub 2A} (5-HT{sub 2A}) receptor is implicated in the pathophysiology of schizophrenia and mood disorders, and in vivo studies of this receptor would be of value in studying the pathophysiology of these disorders and in measuring the relationship of clinical response to receptor occupancy for 5-HT{sub 2A} antagonists such as atypical antipsychotics. Therefore, (2R,4R)-4-hydroxy-2-[2-[2-[2-(3-methoxy)-phenyl]ethyl] phenoxy]ethyl-1-methylpyrrolidine (MPM) (13), a selective and high-affinity (K {sub i}=0.79 nM) 5HT{sub 2A} antagonist, has been radiolabeled with carbon-11 by O-methylation of the corresponding desmethyl analogue (2R,4R)-4-hydroxy-2-[2-[2-[2-(3-hydroxy)phenyl]ethyl]phenoxy] ethyl-1-methylpyrrolidine (12) with [{sup 11}C]methyltriflate in order to determine the suitability of [{sup 11}C]MPM to quantify 5-HT{sub 2A} in living brain using PET. Desmethyl-MPM 12 and standard MPM were prepared, starting from 3-hydroxymethylphenol (2), in excellent yield. The yield obtained for radiolabeling was 40{+-}5% (EOB), and the total synthesis time was 30 min at EOS. PET studies with [{sup 11}C]MPM in baboon showed a distribution in the brain consistent with the known distribution of 5-HT{sub 2A} receptors. The time-activity curves for the high-binding regions peaked at {approx}45 min after injection. Blocking studies with M100907 demonstrated not only 38-57% blocking of tracer binding in brain regions known to have 5-HT{sub 2A} receptors but also 38% blocking in cerebellum, which has a low 5-HT{sub 2A} receptor concentration. Although [{sup 11}C]MPM exhibits appropriate kinetics in baboon for imaging 5-HT{sub 2A} receptors, its specific binding in cerebellum and higher proportion of nonspecific binding limit its usefulness for the in vivo quantification of 5-HT{sub 2A} receptors with PET.

Efficiency of solvent extraction methods for the determination of methyl mercury in forest soils

Energy Technology Data Exchange (ETDEWEB)

Qian, J. [Department of Forest Ecology, Swedish University of Agricultural Sciences, Umeaa (Sweden); Dept. of Analytical Chemistry, Umeaa Univ. (Sweden); Skyllberg, U. [Department of Forest Ecology, Swedish University of Agricultural Sciences, Umeaa (Sweden); Tu, Q.; Frech, W. [Dept. of Analytical Chemistry, Umeaa Univ. (Sweden); Bleam, W.F. [Dept. of Soil Science, University of Wisconsin, Madison, WI (United States)

2000-07-01

Methyl mercury was determined by gas chromatography, microwave induced plasma, atomic emission spectrometry (GC-MIP-AES) using two different methods. One was based on extraction of mercury species into toluene, pre-concentration by evaporation and butylation of methyl mercury with a Grignard reagent followed by determination. With the other, methyl mercury was extracted into dichloromethane and back extracted into water followed by in situ ethylation, collection of ethylated mercury species on Tenax and determination. The accuracy of the entire procedure based on butylation was validated for the individual steps involved in the method. Methyl mercury added to various types of soil samples showed an overall average recovery of 87.5%. Reduced recovery was only caused by losses of methyl mercury during extraction into toluene and during pre-concentration by evaporation. The extraction of methyl mercury added to the soil was therefore quantitative. Since it is not possible to directly determine the extraction efficiency of incipient methyl mercury, the extraction efficiency of total mercury with an acidified solution containing CuSO{sub 4} and KBr was compared with high-pressure microwave acid digestion. The solvent extraction efficiency was 93%. For the IAEA 356 sediment certified reference material, mercury was less efficiently extracted and determined methyl mercury concentrations were below the certified value. Incomplete extraction could be explained by the presence of a large part of inorganic sulfides, as determined by x-ray absorption near-edge structure spectroscopy (XANES). Analyses of sediment reference material CRM 580 gave results in agreement with the certified value. The butylation method gave a detection limit for methyl mercury of 0.1 ng g{sup -1}, calculated as three times the standard deviation for repeated analysis of soil samples. Lower values were obtained with the ethylation method. The precision, expressed as RSD for concentrations 20 times

Simultaneous Determination of Salicylic Acid, Jasmonic Acid, Methyl Salicylate, and Methyl Jasmonate from Ulmus pumila Leaves by GC-MS

Directory of Open Access Journals (Sweden)

Zhi-hong Huang

2015-01-01

Full Text Available Salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate are important phytohormones and defensive signaling compounds, so it is of great importance to determine their levels rapidly and accurately. The study uses Ulmus pumila leaves infected by Tetraneura akinire Sasaki at different stages as materials; after extraction with 80% methanol and ethyl acetate and purification with primary secondary amine (PSA and graphitized carbon blacks (GCB, the contents of signal compounds salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate were determined by GC-MS. The results showed that the level of salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate increased remarkably in U. pumila once infected by T. akinire Sasaki, but the maximums of these four compounds occurred at different times. Salicylic acid level reached the highest at the early stage, and jasmonic acid level went to the maximum in the middle stage; by contrast, change of content of methyl salicylate and methyl jasmonate was the quite opposite.

Simultaneous Determination of Salicylic Acid, Jasmonic Acid, Methyl Salicylate, and Methyl Jasmonate from Ulmus pumila Leaves by GC-MS.

Science.gov (United States)

Huang, Zhi-Hong; Wang, Zhi-Li; Shi, Bao-Lin; Wei, Dong; Chen, Jian-Xin; Wang, Su-Li; Gao, Bao-Jia

2015-01-01

Salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate are important phytohormones and defensive signaling compounds, so it is of great importance to determine their levels rapidly and accurately. The study uses Ulmus pumila leaves infected by Tetraneura akinire Sasaki at different stages as materials; after extraction with 80% methanol and ethyl acetate and purification with primary secondary amine (PSA) and graphitized carbon blacks (GCB), the contents of signal compounds salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate were determined by GC-MS. The results showed that the level of salicylic acid, jasmonic acid, methyl salicylate, and methyl jasmonate increased remarkably in U. pumila once infected by T. akinire Sasaki, but the maximums of these four compounds occurred at different times. Salicylic acid level reached the highest at the early stage, and jasmonic acid level went to the maximum in the middle stage; by contrast, change of content of methyl salicylate and methyl jasmonate was the quite opposite.

Kinetics and thermodynamics of oxidation mediated reaction in L-cysteine and its methyl and ethyl esters in dimethyl sulfoxide-d6 by NMR spectroscopy

Science.gov (United States)

Dougherty, Ryan J.; Singh, Jaideep; Krishnan, V. V.

2017-03-01

L-Cysteine (L-Cys), L-Cysteine methyl ester (L-CysME) or L-Cysteine ethyl ester (L-CysEE), when dissolved in dimethyl sulfoxide, undergoes an oxidation process. This process is slow enough and leads to nuclear magnetic resonance (NMR) spectral changes that could be monitored in real time. The oxidation mediated transition is modeled as a pseudo-first order kinetics and the thermodynamic parameters are estimated using the Eyring's formulation. L-Cysteine and their esters are often used as biological models due to the remarkable thiol group that can be found in different oxidation states. This oxidation mediated transition is due to the combination of thiol oxidation to a disulfide followed by solvent-induced effects may be relevant in designing cysteine-based molecular models.

Characterization of γ-radiation induced polymerization in ethyl methacrylate and methyl acrylate monomers solutions

Science.gov (United States)

Baccaro, Stefania; Casieri, Cinzia; Cemmi, Alessia; Chiarini, Marco; D'Aiuto, Virginia; Tortora, Mariagrazia

2017-12-01

The present work is focused on the γ-radiation induced polymerization of ethyl methacrylate (EMA) and methyl acrylate (MA) monomers mixture to obtain a co-polymer with specific features. The effect of the irradiation parameters (radiation absorbed dose, dose rate) and of the environmental atmosphere on the features of the final products was investigated. Attenuated Total Reflectance - Fourier Transform Infrared Spectroscopy (ATR-FTIR) and Nuclear Magnetic Resonance high-resolution analyses of hydrogen and carbon nuclei (1H and 13C NMR) were applied to follow the γ-induced modifications by monitoring the co-polymerization process and allowed the irradiation parameters optimization. Diffusion-Ordered NMR (DOSY-NMR) data were used to evaluate the co-polymers polydispersity and polymerization degree. Since the last parameter is strongly influenced by the γ radiation and environmental conditions, a comparison among samples prepared and irradiated in air and under nitrogen atmosphere was carried out. In presence of oxygen, higher radiation was required to obtain a full solid co-polymer since a partial amount of energy released to the samples was involved in competitive processes, i.e. oxygen-containing free radicals formation and primary radicals recombination. Irrespectively to the environmental atmosphere, more homogeneous samples in term of polymerization degree dispersion was achieved at lower dose rates. At radiation absorbed doses higher than those needed for the formation of the co-polymer, while in case of samples irradiated in air heavy depolymerization was verified, a sensible increase of the samples stability was attained if the irradiation was performed under nitrogen atmosphere.

Modified montmorillonite as a heterogeneous catalyst in (m)ethyl esterification reaction of lauric acid; Montmorilonita modificada como catalisador heterogeneo em reacoes de esterificacao (M)etilica de acido laurico

Energy Technology Data Exchange (ETDEWEB)

Zatta, Leandro; Nepel, Angelita; Barison, Andersson; Wypych, Fernando, E-mail: wypych@ufpr.br [Departamento de Quimica, Universidade Federal do Parana (UFPR), Curitiba , PR (Brazil)

2012-07-01

Montmorillonite was modified with zirconium polyoxycations in the presence of ammonium sulphate. The material was characterized and used as a catalyst in the esterification of lauric acid, the reactions being accompanied by 2{sup 3} factorial design. Conversions of up to 95.33 and 83.35% were observed for the methyl and ethyl esterification reactions respectively, proving superior to results obtained by thermal conversion. The material was submitted to three reaction cycles and similar conversions were observed, indicating the catalyst is not significantly deactivated after reuse. The catalyst was also tested under reflux conditions, yielding a maximum conversion of 36.86%. (author)

Diagnostic markers of urothelial cancer based on DNA methylation analysis

International Nuclear Information System (INIS)

Chihara, Yoshitomo; Hirao, Yoshihiko; Kanai, Yae; Fujimoto, Hiroyuki; Sugano, Kokichi; Kawashima, Kiyotaka; Liang, Gangning; Jones, Peter A; Fujimoto, Kiyohide; Kuniyasu, Hiroki

2013-01-01

Early detection and risk assessment are crucial for treating urothelial cancer (UC), which is characterized by a high recurrence rate, and necessitates frequent and invasive monitoring. We aimed to establish diagnostic markers for UC based on DNA methylation. In this multi-center study, three independent sample sets were prepared. First, DNA methylation levels at CpG loci were measured in the training sets (tumor samples from 91 UC patients, corresponding normal-appearing tissue from these patients, and 12 normal tissues from age-matched bladder cancer-free patients) using the Illumina Golden Gate methylation assay to identify differentially methylated loci. Next, these methylated loci were validated by quantitative DNA methylation by pyrosequencing, using another cohort of tissue samples (Tissue validation set). Lastly, methylation of these markers was analyzed in the independent urine samples (Urine validation set). ROC analysis was performed to evaluate the diagnostic accuracy of these 12 selected markers. Of the 1303 CpG sites, 158 were hyper ethylated and 356 were hypo ethylated in tumor tissues compared to normal tissues. In the panel analysis, 12 loci showed remarkable alterations between tumor and normal samples, with 94.3% sensitivity and 97.8% specificity. Similarly, corresponding normal tissue could be distinguished from normal tissues with 76.0% sensitivity and 100% specificity. Furthermore, the diagnostic accuracy for UC of these markers determined in urine samples was high, with 100% sensitivity and 100% specificity. Based on these preliminary findings, diagnostic markers based on differential DNA methylation at specific loci can be useful for non-invasive and reliable detection of UC and epigenetic field defect

Li-Ion Cells Employing Electrolytes With Methyl Propionate and Ethyl Butyrate Co-Solvents

Science.gov (United States)

Smart, Marshall C.; Bugga, Ratnakumar V.

2011-01-01

Future NASA missions aimed at exploring Mars and the outer planets require rechargeable batteries that can operate at low temperatures to satisfy the requirements of such applications as landers, rovers, and penetrators. A number of terrestrial applications, such as hybrid electric vehicles (HEVs) and electric vehicles (EVs) also require energy storage devices that can operate over a wide temperature range (i.e., -40 to +70 C), while still providing high power capability and long life. Currently, the state-of-the-art lithium-ion system has been demonstrated to operate over a wide range of temperatures (-30 to +40 C); however, the rate capability at the lower temperatures is very poor. These limitations at very low temperatures are due to poor electrolyte conductivity, poor lithium intercalation kinetics over the electrode surface layers, and poor ionic diffusion in the electrode bulk. Two wide-operating-temperature-range electrolytes have been developed based on advances involving lithium hexafluorophosphate-based solutions in carbonate and carbonate + ester solvent blends, which have been further optimized in the context of the technology and targeted applications. The approaches employed include further optimization of electrolytes containing methyl propionate (MP) and ethyl butyrate (EB), which are effective co-solvents, to widen the operating temperature range beyond the baseline systems. Attention was focused on further optimizing ester-based electrolyte formulations that have exhibited the best performance at temperatures ranging from -60 to +60 C, with an emphasis upon improving the rate capability at -20 to -40 C. This was accomplished by increasing electrolyte salt concentration to 1.20M and increasing the ester content to 60 percent by volume to increase the ionic conductivity at low temperatures. Two JPL-developed electrolytes 1.20M LiPF6 in EC+EMC+MP (20:20:60 v/v %) and 1.20M LiPF6 in EC+EMC+EB (20:20:60 v/v %) operate effectively over a wide

Atmospheric mixing ratios of methyl ethyl ketone (2-butanone in tropical, boreal, temperate and marine environments

Directory of Open Access Journals (Sweden)

A. M. Yáñez-Serrano

2016-09-01

Full Text Available Methyl ethyl ketone (MEK enters the atmosphere following direct emission from vegetation and anthropogenic activities, as well as being produced by the gas-phase oxidation of volatile organic compounds (VOCs such as n-butane. This study presents the first overview of ambient MEK measurements at six different locations, characteristic of forested, urban and marine environments. In order to understand better the occurrence and behaviour of MEK in the atmosphere, we analyse diel cycles of MEK mixing ratios, vertical profiles, ecosystem flux data, and HYSPLIT back trajectories, and compare with co-measured VOCs. MEK measurements were primarily conducted with proton-transfer-reaction mass spectrometer (PTR-MS instruments. Results from the sites under biogenic influence demonstrate that vegetation is an important source of MEK. The diel cycle of MEK follows that of ambient temperature and the forest structure plays an important role in air mixing. At such sites, a high correlation of MEK with acetone was observed (e.g. r2 = 0.96 for the SMEAR Estonia site in a remote hemiboreal forest in Tartumaa, Estonia, and r2 = 0.89 at the ATTO pristine tropical rainforest site in central Amazonia. Under polluted conditions, we observed strongly enhanced MEK mixing ratios. Overall, the MEK mixing ratios and flux data presented here indicate that both biogenic and anthropogenic sources contribute to its occurrence in the global atmosphere.

Ultrasonic velocities, densities, and excess molar volumes of binary mixtures of N,N-dimethyl formamide with methyl acrylate, or ethyl acrylate, or butyl acrylate, or 2-ethyl hexyl acrylate at T = 308.15 K

Energy Technology Data Exchange (ETDEWEB)

Kondaiah, M. [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar 522510, Andhra Pradesh (India); Sravana Kumar, D. [Dr. V.S. Krishna Govt. Degree College, Visakhapatnam, Andhra Pradesh (India); Sreekanth, K. [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar 522510, Andhra Pradesh (India); Krishna Rao, D., E-mail: krdhanekula@yahoo.co.in [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar 522510, Andhra Pradesh (India)

2011-12-15

Highlights: > Positive values of V{sub m}{sup E}, indicate dispersion forces between acrylic esters and DMF. > V{sub m}{sup E} values compared with Redlich-Kister polynomial. > Partial molar volumes data conclude that weak interactions exist in the systems. > Measured velocity values compared with theoretical values obtained by polynomials. - Abstract: Ultrasonic velocities, u, densities, {rho}, of binary mixtures of N,N-dimethyl formamide (DMF) with methyl acrylate (MA), ethyl acrylate (EA), butyl acrylate (BA), and 2-ethyl hexyl acrylate (EHA), including pure liquids, over the entire composition range have been measured at T = 308.15 K. Using the experimental results, the excess molar volume, V{sub m}{sup E}, partial molar volumes, V-bar {sub m,1}, V-bar{sub m,2}, and excess partial molar volumes, V-bar{sub m,1}{sup E}, V-bar{sub m,2}{sup E} have been calculated. Molecular interactions in the systems have been studied in the light of variation of excess values of calculated properties. The excess properties have been fitted to Redlich-Kister type polynomial and the corresponding standard deviations have been calculated. The positive values of V{sub m}{sup E} indicate the presence of dispersion forces between the DMF and acrylic ester molecules. Further theoretical values of sound velocity in the mixtures have been evaluated using various theories and have been compared with experimental sound velocities to verify the applicability of such theories to the systems studied. Theoretical ultrasonic velocity data have been used to study molecular interactions in the binary systems investigated.

Ferrocene Compounds. XXVI. C- and O-Ferrocenylalkylation of Methyl Salicylate

OpenAIRE

Kovač, Veronika; Rapić, Vladimir; Alagić, Jasmina; Barišić, Lidija

1999-01-01

Reaction of equimolar amounts of methyl salicylate, sodium and N,N,N-trimethylferrocylammonium iodide (1a) in ethanol gave 55% of ethyl 1-ferrocenylethyl ether (4). By refluxing a solution of 9 mmol sodium and 3 mmol of FcCHRNMe3I (1a, R = H; 1b, R = Me; 1c, R = Ph) in a large excess of methyl salicylate for 2-3 hours, the corresponding methyl 5-ferrocylsalicylates (5) (10-23%) and methyl-3-ferrocylsalicylates (6) (12-20%) were obtained. During conversion of salt 1b, besides of 5b and 6b, 20%...

Synthesis of (R,S)-[2,3-13C2]-1-(1'-methyl-2'-pyrrolidinyl)propan-2-one; {(R,S)-[2',3'-13C2]hygrinePound right bracePound

International Nuclear Information System (INIS)

Abraham, T.W.; Leete, Edward

1996-01-01

2-Ethoxy-1-methyl-5-pyrrolidinone (1) was reacted with ethyl [3,4- 13 C 2 ]-acetoacetate (2) in the presence of TiCl 4 to give ethyl [3,4- 13 C 2 ]-2-(1'-methyl-5'-oxo-2'-pyrrolidinyl)-3-oxobutanoate (3) in 85% yield. Decarboethoxylation of ethyl [3,4- 13 C 2 ]-2-(1'-methyl-5'-oxo-2'-pyrrolidinyl)-3-oxobutan-oate (3) was accomplished using NaCl and H 2 O in DMSO to give (R,S)-[2,3- 13 C 2 ]-1-(1'-methyl-5'-oxo-2'-pyrrolidinyl)propan-2-o ne (4) in 91% yield. Protection of the ketone as a ketal (ethylene glycol, H + ), followed by reduction of the amide to the amine using LiAlH 4 and subsequent deprotection of the ketal gave (R,S)-[2,3- 13 C 2 ]-1-(1'-methyl-2'-pyrrolidinyl)propan-2-one ((R,s)-[2', 3'- 13 C 2 ]Hygrine) (8) in 78% yield. (61% overall yield from ethyl [3,4- 13 C 2 ]acetoacetate). (Author)

Influence of degree of methyl methacrylate polymerization on spectroscopic properties of ethyl 5-(4-aminophenyl)- and 5-(4-dimethylaminophenyl)-3-amino-2,4-dicyanobenzoate

International Nuclear Information System (INIS)

Józefowicz, M.; Bajorek, A.; Pietrzak, M.; Jędrzejewska, B.; Heldt, J.R.; Heldt, J.

2013-01-01

The influence of degree of methyl methacrylate (MM) polymerization on the both emission modes (LE—locally excited and ICT—intramolecular charge transfer) of the fluorescence spectrum of ethyl 5-(4-aminophenyl)-3-amino-2,4-dicyanobenzoate (EAADCy) and ethyl 5-(4-dimethylaminophenyl)-3-amino-2,4-dicyanobenzoate (EDMAADCy) has been studied using steady-state and time-resolved spectroscopic technique. The purpose of these studies was to find a relationship between the changes in the spectroscopic characteristics (fluorescence intensity, wavelength of maximum intensity, fluorescence full-width at half maximum, emission anisotropy, fluorescence decay time) of the tested compounds and degree of monomer conversion into polymer. On the basis of the experimental results, it was shown that the ICT fluorescence full-width at half maximum for EDMAADCy shows a linear dependence on the time of MM polymerization. Our findings predestine the molecule EDMAADCy to be used as fluorescence probe for monitoring the polymerization process of MM. - Highlights: ► The fluorescence excitation and emission spectra in MM possess a complex nature. ► Fluorescence decay kinetics for different degrees of polymerization of MM were investigated. ► The ICT fluorescence FWHM for EDMAADCy shows a linear dependence on the time of polymerization. ► EDMAADCy can be used as fluorescence probe for monitoring the polymerization process of MM

Novel fatty acid methyl esters from the actinomycete Micromonospora aurantiaca

Science.gov (United States)

Bruns, Hilke; Riclea, Ramona

2011-01-01

Summary The volatiles released by Micromonospora aurantiaca were collected by means of a closed-loop stripping apparatus (CLSA) and analysed by GC–MS. The headspace extracts contained more than 90 compounds from different classes. Fatty acid methyl esters (FAMEs) comprised the major compound class including saturated unbranched, monomethyl and dimethyl branched FAMEs in diverse structural variants: Unbranched, α-branched, γ-branched, (ω−1)-branched, (ω−2)-branched, α- and (ω−1)-branched, γ- and (ω−1)-branched, γ- and (ω−2)-branched, and γ- and (ω−3)-branched FAMEs. FAMEs of the last three types have not been described from natural sources before. The structures for all FAMEs have been suggested based on their mass spectra and on a retention index increment system and verified by the synthesis of key reference compounds. In addition, the structures of two FAMEs, methyl 4,8-dimethyldodecanoate and the ethyl-branched compound methyl 8-ethyl-4-methyldodecanoate were deduced from their mass spectra. Feeding experiments with isotopically labelled [2H10]leucine, [2H10]isoleucine, [2H8]valine, [2H5]sodium propionate, and [methyl-2H3]methionine demonstrated that the responsible fatty acid synthase (FAS) can use different branched and unbranched starter units and is able to incorporate methylmalonyl-CoA elongation units for internal methyl branches in various chain positions, while the methyl ester function is derived from S-adenosyl methionine (SAM). PMID:22238549

Use of tobacco seed oil methyl ester in a turbocharged indirect injection diesel engine

International Nuclear Information System (INIS)

Usta, N.

2005-01-01

Vegetable oils and their methyl/ethyl esters are alternative renewable fuels for compression ignition engines. Different kinds of vegetable oils and their methyl/ethyl esters have been tested in diesel engines. However, tobacco seed oil and tobacco seed oil methyl ester have not been tested in diesel engines, yet. Tobacco seed oil is a non-edible vegetable oil and a by-product of tobacco leaves production. To the author's best knowledge, this is the first study on tobacco seed oil methyl ester as a fuel in diesel engines. In this study, potential tobacco seed production throughout the world, the oil extraction process from tobacco seed and the transesterification process for biodiesel production were examined. The produced tobacco seed oil methyl ester was characterized by exposing its major properties. The effects of tobacco seed oil methyl ester addition to diesel No. 2 on the performance and emissions of a four cycle, four cylinder turbocharged indirect injection (IDI) diesel engine were examined at both full and partial loads. Experimental results showed that tobacco seed oil methyl ester can be partially substituted for the diesel fuel at most operating conditions in terms of performance parameters and emissions without any engine modification and preheating of the blends. (Author)

9-Ethyl-2,3-dihydro-9H-carbazol-4(1H-one

Directory of Open Access Journals (Sweden)

S. Sriman Narayanan

2008-09-01

Full Text Available In the title compound, C28H30N2O2, the cyclohexene ring system adopts a sofa conformation. The crystal structure is stabilized by C—H...O interactions between methyl H atoms of the ethyl substituents and the O atoms of carbonyl groups of adjacent molecules, and by an intermolecular carbonyl–carbonyl interactions [3.207 (2 Å

Kinetics of exchange between zero-, one-, and two-hydrogen-bonded states of methyl and ethyl acetate in methanol.

Science.gov (United States)

Chuntonov, Lev; Pazos, Ileana M; Ma, Jianqiang; Gai, Feng

2015-03-26

It has recently been shown that the ester carbonyl stretching vibration can be used as a sensitive probe of local electrostatic field in molecular systems. To further characterize this vibrational probe and extend its potential applications, we studied the kinetics of chemical exchange between differently hydrogen-bonded (H-bonded) ester carbonyl groups of methyl acetate (MA) and ethyl acetate (EA) in methanol. We found that, while both MA and EA can form zero, one, or two H-bonds with the solvent, the population of the 2hb state in MA is significantly smaller than that in EA. Using a combination of linear and nonlinear infrared measurements and numerical simulations, we further determined the rate constants for the exchange between these differently H-bonded states. We found that for MA the chemical exchange reaction between the two dominant states (i.e., 0hb and 1hb states) has a relaxation rate constant of 0.14 ps(-1), whereas for EA the three-state chemical exchange reaction occurs in a predominantly sequential manner with the following relaxation rate constants: 0.11 ps(-1) for exchange between 0hb and 1hb states and 0.12 ps(-1) for exchange between 1hb and 2hb states.

Stimulation of {sup 125}I-3-iodo-{alpha}-methyl-L-tyrosine uptake in Chinese hamster ovary (CHO-K1) cells by tyrosine esters

Energy Technology Data Exchange (ETDEWEB)

Shikano, Naoto [Department of Radiological Sciences, Center for Medical Sciences and Center for Humanities and Sciences, Ibaraki Prefectural University of Health Sciences, Inashiki-gun, Ibaraki (Japan)], E-mail: sikano@ipu.ac.jp; Ogura, Masato; Sagara, Jun-ichi; Nakajima, Syuichi [Department of Radiological Sciences, Center for Medical Sciences and Center for Humanities and Sciences, Ibaraki Prefectural University of Health Sciences, Inashiki-gun, Ibaraki (Japan); Kobayashi, Masato [Division of Health Science, Graduate School of Health Sciences, Kanazawa University, Kanazawa, Ishikawa (Japan); Baba, Takeshi; Yamaguchi, Naoto; Iwamura, Yukio; Kubota, Nobuo [Department of Radiological Sciences, Center for Medical Sciences and Center for Humanities and Sciences, Ibaraki Prefectural University of Health Sciences, Inashiki-gun, Ibaraki (Japan); Kawai, Keiichi [Division of Health Science, Graduate School of Health Sciences, Kanazawa University, Kanazawa, Ishikawa (Japan)

2010-02-15

Introduction: Transport of the amino acid analog {sup 123}I-3-iodo-{alpha}-methyl-L-tyrosine, which is used in clinical SPECT imaging, occurs mainly via L-type amino acid transporter type 1 (LAT1; an amino acid exchanger). As LAT1 is highly expressed in actively proliferating tumors, we made a preliminary investigation of the effects of amino acid esters on enhancement of {sup 125}I-3-iodo-{alpha}-methyl-L-tyrosine (IMT) uptake via LAT1 in Chinese hamster ovary (CHO-K1) cells. Methods: Because the sequence of the CHO-K1 LAT1 gene is not available, we confirmed LAT1 expression through IMT (18.5 kBq) uptake mechanisms using specific inhibitors. L-Gly, L-Ser, L-Leu, L-Phe, L-Met, L-Tyr, D-Tyr, L-Val and L-Lys ethyl/methyl esters were tested in combination with IMT. Time-course studies over a 3-h period were conducted, and the concentration dependence of L-Tyr ethyl and methyl esters (0.001 to 10 mM) in combination with IMT was also examined. For a proof of de-esterification of L- and D-Tyr ethyl and methyl esters in the cells (by enzymatic attack or other cause), the concentration of L- and D-Tyr was analyzed by high-performance liquid chromatography of the esters in phosphate buffer (pH 7.4) and cell homogenates at 37 deg. C or under ice-cold conditions. Results: Inhibition tests suggested that LAT1 is involved in IMT uptake by CHO-K1 cells. Co-administration of 1 mM of L-Tyr ethyl or methyl ester with IMT produced the greatest enhancement. The de-esterification reaction was stereo selective and temperature dependent in the homogenate. De-esterification kinetics were very fast in the homogenate and very slow in the phosphate buffer. Conclusions: The L-Tyr ethyl or methyl esters were the most effective enhancers of IMT uptake into CHO-K1 cells and acted by trans-stimulation of the amino acid exchange function of LAT1. This result suggests that de-esterification in the cells may be caused by enzymatic attack. We will use IMT and L-Tyr ethyl or methyl esters to examine

Two Players Make a Formidable Combination: In Situ Generated Poly(acrylic anhydride-2-methyl-acrylic acid-2-oxirane-ethyl ester-methyl methacrylate) Cross-Linking Gel Polymer Electrolyte toward 5 V High-Voltage Batteries.

Science.gov (United States)

Ma, Yue; Ma, Jun; Chai, Jingchao; Liu, Zhihong; Ding, Guoliang; Xu, Gaojie; Liu, Haisheng; Chen, Bingbing; Zhou, Xinhong; Cui, Guanglei; Chen, Liquan

2017-11-29

Electrochemical performance of high-voltage lithium batteries with high energy density is limited because of the electrolyte instability and the electrode/electrolyte interfacial reactivity. Hence, a cross-linking polymer network of poly(acrylic anhydride-2-methyl-acrylic acid-2-oxirane-ethyl ester-methyl methacrylate) (PAMM)-based electrolyte was introduced via in situ polymerization inspired by "shuangjian hebi", which is a statement in a traditional Chinese Kungfu story similar to the synergetic effect of 1 + 1 > 2. A poly(acrylic anhydride) and poly(methyl methacrylate)-based system is very promising as electrolyte materials for lithium-ion batteries, in which the anhydride and acrylate groups can provide high voltage resistance and fast ionic conductivity, respectively. As a result, the cross-linking PAMM-based electrolyte possesses a significant comprehensive enhancement, including electrochemical stability window exceeding 5 V vs Li + /Li, an ionic conductivity of 6.79 × 10 -4 S cm -1 at room temperature, high mechanical strength (27.5 MPa), good flame resistance, and excellent interface compatibility with Li metal. It is also demonstrated that this gel polymer electrolyte suppresses the negative effect resulting from dissolution of Mn 2+ ions at 25 and 55 °C. Thus, the LiNi 0.5 Mn 1.5 O 4 /Li and LiNi 0.5 Mn 1.5 O 4 /Li 4 Ti 5 O 12 cells using the optimized in situ polymerized cross-linking PAMM-based gel polymer electrolyte deliver stable charging/discharging profiles and excellent rate performance at room temperature and even at 55 °C. These findings suggest that the cross-linking PAMM is an intriguing candidate for 5 V class high-voltage gel polymer electrolyte toward high-energy lithium-on batteries.

[Chemical Constituents from Ethyl Acetate Extract of Psidium guajava Leaves (II)].

Science.gov (United States)

Ouyang, Wen; Zhu, Xiao-ai; He, Cui-xia; Chen, Xue-xiang; Ye, Shu-min; Peng, Shan; Cao, Yong

2015-08-01

To study the chemical constituents from ethyl acetate extract of Psidium guajava leaves. The constituents were separated and purified by silica gel and Sephadex LH-20 column chromatography and their structures were identified on the basis of physicochemical properties and spectral data. Eleven compounds were isolated and identified as 6,10,14-trimethyl-2-pentadecanone (1), phytyl-acetate (2), cubenol (3), eucalyptin (4), n-docosanoic acid-p-hydroxy-phenethylol ester (5),8-methyl-5,7- dihydroxy-flavonone (6), 6-methyl-5,7-dihydroxy-flavonone (7), betulinic acid (8), carnosol (9), quercetin (10), and 2,4,6-tirhydroxy- 3,5-dimethyl-diphenylketone-4-O-(6'"-O-galloyl)-β-D-glucoside (11). Compounds 1-9 are isolated from this plant for the first time.

Synthesis of two potential NK1-receptor ligands using [1-11C]ethyl iodide and [1-11C]propyl iodide and initial PET-imaging

Directory of Open Access Journals (Sweden)

Genchel Tove

2007-07-01

Full Text Available Abstract Background The previously validated NK1-receptor ligand [O-methyl-11C]GR205171 binds with a high affinity to the NK1-receptor and displays a slow dissociation from the receptor. Hence, it cannot be used in vivo for detecting concentration changes in substance P, the endogenous ligand for the NK1-receptor. A radioligand used for monitoring these changes has to enable displacement by the endogenous ligand and thus bind reversibly to the receptor. Small changes in the structure of a receptor ligand can lead to changes in binding characteristics and also in the ability to penetrate the blood-brain barrier. The aim of this study was to use carbon-11 labelled ethyl and propyl iodide with high specific radioactivity in the synthesis of two new and potentially reversible NK1-receptor ligands with chemical structures based on [O-methyl-11C]GR205171. Methods [1-11C]Ethyl and [1-11C]propyl iodide with specific radioactivities of 90 GBq/μmol and 270 GBq/μmol, respectively, were used in the synthesis of [O-methyl-11C]GR205171 analogues by alkylation of O-desmethyl GR205171. The brain uptake of the obtained (2S,3S-N-(1-(2- [1-11C]ethoxy-5-(3-(trifluoromethyl-4H-1,2,4-triazol-4-ylphenylethyl-2-phenylpiperidin-3-amine (I and (2S,3S-2-phenyl-N-(1-(2- [1-11C]propoxy-5-(3-(trifluoromethyl-4H-1,2,4-triazol-4-ylphenylethylpiperidin-3-amine (II was studied with PET in guinea pigs and rhesus monkeys and compared to the uptake of [O-methyl-11C]GR205171. Results All ligands had similar uptake distribution in the guinea pig brain. The PET-studies in rhesus monkeys showed that (II had no specific binding in striatum. Ligand (I had moderate specific binding compared to the [O-methyl-11C]GR205171. The ethyl analogue (I displayed reversible binding characteristics contrary to the slow dissociation rate shown by [O-methyl-11C]GR205171. Conclusion The propyl-analogue (II cannot be used for detecting changes in NK1-ligand levels, while further studies should be

Vanillin as a modulator agent in SMART test: inhibition in the steps that precede N-methyl-N-nitrosourea-, N-ethyl-N-nitrosourea-, ethylmethanesulphonate- and bleomycin-genotoxicity.

Science.gov (United States)

Sinigaglia, Marialva; Lehmann, Maurício; Baumgardt, Paula; do Amaral, Viviane Souza; Dihl, Rafael Rodrigues; Reguly, Maria Luíza; de Andrade, Heloísa Helena Rodrigues

2006-09-05

Vanillin (VA), the world's major flavoring compound used in food industry and confectionery products - that has antimutagenic and anticarcinogenic activity against a variety of mutagenic/carcinogenic agents - was tested for the interval between the formation of premutational lesion and it is finalization as a DNA lesion. The overall findings using co-treatment protocols in SMART test suggest that VA can lead to a significant protection against the general genotoxicity of ethylmethanesulphonate (EMS), N-ethyl-N-nitrosourea (ENU), N-methyl-N-nitrosourea (MNU) and bleomycin sulphate (BLEO). Considering MNU, ENU and EMS the desmutagenic activity observed could result from VA-stimulation of detoxification, via induction of glutathione S-transferase. However, the protector effect related to BLEO could be attributed to its powerful scavenger ability, which has the potential to prevent oxidative damage induced by BLEO.

Radiation cured and monomer modified silicon elastomers

International Nuclear Information System (INIS)

Eldred, R.J.

1979-01-01

A method is described for the production of a tear resistant silicone elastomer, which has improved elongation properties. This elastomer is the radiation induced reaction product of a noncured methyl vinyl silicone resin (VMQ) and uniformly dispersed therein a blend of a polyfunctional acrylic crosslinking monomer and a filler

Brahmarasayana protects against Ethyl methanesulfonate or Methyl methanesulfonate induced chromosomal aberrations in mouse bone marrow cells

Directory of Open Access Journals (Sweden)

Guruprasad Kanive

2012-08-01

Full Text Available Abstract Background Ayurveda, the traditional Indian system of medicine has given great emphasis to the promotion of health. Rasayana is one of the eight branches of Ayurveda which refers to rejuvenant therapy. It has been reported that rasayanas have immuno-modulatory, antioxidant and antitumor functions, however, the genotoxic potential and modulation of DNA repair of many rasayanas have not been evaluated. Methods The present study assessed the role of Brahmarasayana (BR on Ethyl methanesulfonate (EMS-and Methyl methanesulfonate (MMS-induced genotoxicity and DNA repair in in vivo mouse test system. The mice were orally fed with BR (5 g or 8 mg / day for two months and 24 h later EMS or MMS was given intraperitoneally. The genotoxicity was analyzed by chromosomal aberrations, sperm count, and sperm abnormalities. Results The results have revealed that BR did not induce significant chromosomal aberrations when compared to that of the control animals (p >0.05. On the other hand, the frequencies of chromosomal aberrations induced by EMS (240 mg / kg body weight or MMS (125 mg / kg body weight were significantly higher (p Conclusion The effect of BR, as it relates to antioxidant activity was not evident in liver tissue however rasayana treatment was observed to increase constitutive DNA base excision repair and reduce clastogenicity. Whilst, the molecular mechanisms of such repair need further exploration, this is the first report to demonstrate these effects and provides further evidence for the role of brahmarasayana in the possible improvement of quality of life.

Vibrational spectroscopic (FT-IR, FT-Raman) and quantum mechanical study of 4-(2-chlorophenyl)-2-ethyl-9-methyl-6H-thieno[3,2-f] [1,2,4]triazolo[4,3-a][1,4] diazepine

Science.gov (United States)

Kuruvilla, Tintu K.; Prasana, Johanan Christian; Muthu, S.; George, Jacob

2018-04-01

The spectroscopic properties of 4-(2-chlorophenyl)-2-ethyl-9-methyl-6H-thieno [3,2-f] [1,2,4] triazolo [4,3-a] [1,4] diazepine were investigated in the present study using FT-IR and FT-Raman techniques. The results obtained were compared with quantum mechanical methods, as it serves as an important tool in interpreting and predicting vibrational spectra. The optimized molecular geometry, the vibrational wavenumbers, the infrared intensities and Raman scattering were calculated using density functional theory B3LYP method with 6-311++g (d,p) basis set. All the experimental results were in line with the theoretical data. The molecular electrostatic potential (MEP) and HOMO LUMO energies of the title compound were accounted. The results indicated that the title compound has a lower softness value (0.27) and high electrophilicity index (4.98) hence describing its biological activity. Further, natural bond orbital was also analyzed as part of the work. Fukui functions were calculated in order to explain the chemical selectivity or the reactivity site in 4-(2-chlorophenyl)-2-ethyl-9-methyl-6H-thieno [3,2-f] [1,2,4] triazolo [4,3-a] [1,4] diazepine. The thermodynamic properties of the title compound were closely examined at different temperatures. It revealed the correlations between heat capacity (C), entropy (S) and enthalpy changes (H) with temperatures. The paper further explains that the title compound can act as good antidepressant through molecular docking studies.

Degradation of methyl and ethyl mercury into inorganic mercury by other reactive oxygen species besides hydroxyl radical

Energy Technology Data Exchange (ETDEWEB)

Suda, Ikuo; Takahashi, Hitoshi (Kumamoto Univ. Medical School (Japan). Inst. for Medical Immunology)

1992-01-01

Degradation of methyl mercury (MeHg) and ethyl Hg (EtHg) with reactive oxygens was studied in vitro by using peroxidase-hydrogen peroxide (H{sub 2}O{sub 2})-halide and rose bengal-ultraviolet light A systems. For this purpose, the direct determination method for inorganic Hg was employed. Both systems could effectively degrade EtHg, and MeHg to some extent. Degradation of MeHg and EtHg with the myeloperoxidase (MPO)-H{sub 2}O{sub 2}-chloride system was inhibited by MPO inhibitors (cyanide and azide), catalase, hypochlorous acid (HOCl) scavengers (glycine, alanine, serine and taurine), 1,4-diazabicyclo(2,2,2)octane and 2,5-dimethylfuran, but not by hydroxyl radical scavengers (ethanol and mannitol). Iodide was more effective than chloride as the halide component. Lactoperoxidase (LPO) could substitute for MPO in the iodide, but not the chloride system. With MPO-H{sub 2}O{sub 2}-chloride, MPO-H{sub 2}O{sub 2}-iodide and LPO-H{sub 2}O{sub 2}-iodide systems, we observed the increased degradation of EtHg in deuterium oxide (D{sub 2}O) medium better than that in H{sub 2}O medium. The D{sub 2}O effect upon MeHg degradation was extremely weak. These results suggested that HOCl (or HOI) might be also capable of degrading MeHg and EtHg, besides the hydroxyl radical already reported by us. Singlet oxygen could degrade EtHg but not MeHg. (orig.).

Preparation and properties of titania based ionogels synthesized using ionic liquid 1-ethyl-3-methyl imidazolium thiocyanate

Energy Technology Data Exchange (ETDEWEB)

Verma, Y.L.; Tripathi, A.K.; Shalu; Singh, V.K.; Balo, L.; Gupta, H.; Singh, S.K.; Singh, R.K., E-mail: rajendrasingh.bhu@gmail.com

2017-06-15

Highlights: • Synthesis of titania based ionogels using non-aqueous sol-gel process. • Ionogels are found to be mesoporous structure with uniform pore size distribution. • Ionic liquid extracted TiO{sub 2} matrix reveals the anatase phase of TiO{sub 2}. • Properties of ionic liquid are found to change in TiO{sub 2} matrix. - Abstract: Present study reports the synthesis of titania (TiO{sub 2}) based ionogels using ionic liquid (IL) 1-ethyl-3-methyl imidazolium thiocyanate ([EMIM][SCN]) by non-aqueous sol-gel process. Ionogels are characterized using N{sub 2} adsorption-desorption, TGA, DSC, SEM, TEM, XRD, and FTIR. N{sub 2}-sorption results show that TiO{sub 2} matrices have meso-pores with uniform pore size distribution. Thermal studies reveal that thermal stability of confined IL decreases while the glass transition temperature (T{sub g}) is found to increase. XRD patterns show that IL containing TiO{sub 2} matrices exhibit amorphous (weak crystalline peaks) nature however after extraction of IL from ionogel, it shows the crystalline (anatase) phase of TiO{sub 2} which has also been found from SAED pattern. SEM micrographs reveal that as the amount of IL is increased, TiO{sub 2} particles are found to agglomerate. FTIR results indicate that the vibrational frequencies of confined IL are found to shift due to interaction of IL molecules with titania pore wall surface.

Volumetric properties of room temperature ionic liquid 1. The system of {1-methyl-3-ethylimidazolium ethyl sulfate+water} at temperature in the range (278.15 to 333.15) K

International Nuclear Information System (INIS)

Lu Xingmei; Xu Weiguo; Gui Jinsong; Li Huawei; Yang Jiazhen

2005-01-01

This paper reports densities of aqueous solutions of ionic liquid (IL) 1-methyl-3-ethylimidazolium ethyl sulfate (EMISE) that were measured gravimetrically at temperatures (278.15 to 333.15) K. The values of the apparent molar volume, φ V B and partial molar volume, V-bar B, were determined and apparent molar expansibilities φ E=((∂φ B )/∂T)) p of EMISE and the coefficients of thermal expansion of the solutions, α, were calculated. The values of the apparent molar volume, φ V B , were fitted by the method of least-squares to a Pitzer's equation to determine the parameters, β MX (0)V , β MX (1)V , and C MX V

Overmodulation Control in the Optimization of a H-PDLC Device with Ethyl Eosin as Dye

Directory of Open Access Journals (Sweden)

Manuel Ortuño

2013-01-01

Full Text Available The response of a H-PDLC device is improved by means of a two-step method. First, component optimization—initiator system, crosslinker, and cosolvent—enables the diffraction efficiency of the hologram to be maximized. Second, the use of N-methyl-2-pyrrolidone in combination with N-vinyl-2-pyrrolidone prevents the overmodulation in photopolymers containing ethyl eosin.

Synthesis of (R,S)-[2,3-{sup 13}C{sub 2}]-1-(1`-methyl-2`-pyrrolidinyl)propan-2-one; {l_brace}(R,S)-[2`,3`-{sup 13}C{sub 2}]hygrinePound right bracePound

Energy Technology Data Exchange (ETDEWEB)

Abraham, T.W.; Leete, Edward [Minnesota Univ., Minneapolis, MN (United States). Dept. of Chemistry

1996-05-01

2-Ethoxy-1-methyl-5-pyrrolidinone (1) was reacted with ethyl [3,4-{sup 13}C{sub 2}]-acetoacetate (2) in the presence of TiCl{sub 4} to give ethyl [3,4-{sup 13}C{sub 2}]-2-(1`-methyl-5`-oxo-2`-pyrrolidinyl)-3-oxobutanoate (3) in 85% yield. Decarboethoxylation of ethyl [3,4-{sup 13}C{sub 2}]-2-(1`-methyl-5`-oxo-2`-pyrrolidinyl)-3-oxobutan-oate (3) was accomplished using NaCl and H{sub 2}O in DMSO to give (R,S)-[2,3-{sup 13}C{sub 2}]-1-(1`-methyl-5`-oxo-2`-pyrrolidinyl)propan-2-o ne (4) in 91% yield. Protection of the ketone as a ketal (ethylene glycol, H{sup +}), followed by reduction of the amide to the amine using LiAlH{sub 4} and subsequent deprotection of the ketal gave (R,S)-[2,3-{sup 13}C{sub 2}]-1-(1`-methyl-2`-pyrrolidinyl)propan-2-one ((R,s)-[2`, 3`-{sup 13}C{sub 2}]Hygrine) (8) in 78% yield. (61% overall yield from ethyl [3,4-{sup 13}C{sub 2}]acetoacetate). (Author).

21 CFR 584.200 - Ethyl alcohol containing ethyl acetate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ethyl alcohol containing ethyl acetate. 584.200 Section 584.200 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS...

Emission Studies in CI Engine using LPG and Palm Kernel Methyl Ester as Fuels and Di-ethyl Ether as an Additive

Science.gov (United States)

Dora, Nagaraju; Jothi, T. J. Sarvoththama

2018-05-01

The present study investigates the effectiveness of using di-ethyl ether (DEE) as the fuel additive in engine performance and emissions. Experiments are carried out in a single cylinder four stroke diesel engine at constant speed. Two different fuels namely liquefied petroleum gas (LPG) and palm kernel methyl ester (PKME) are used as primary fuels with DEE as the fuel additive. LPG flow rates of 0.6 and 0.8 kg/h are considered, and flow rate of DEE is varied to maintain the constant engine speed. In case of PKME fuel, it is blended with diesel in the latter to the former ratio of 80:20, and DEE is varied in the volumetric proportion of 1 and 2%. Results indicate that for the engine operating in LPG-DEE mode at 0.6 kg/h of LPG, the brake thermal efficiency is lowered by 26%; however, NOx is subsequently reduced by around 30% compared to the engine running with only diesel fuel at 70% load. Similarly, results of PKME blended fuel showed a drastic reduction in the NOx and CO emissions. In these two modes of operation, DEE is observed to be significant fuel additive regarding emissions reduction.

Synthesis and investigation of solvent effects on the ultraviolet absorption spectra of 5-substituted-4-methyl-3-cyano-6-hydroxy-2-pyridones

Directory of Open Access Journals (Sweden)

NATASA V. VALENTIC

2001-08-01

Full Text Available A number of 5-substituted-4-methyl-3-cyano-6-hydroxy-2-pyridones from cyanoacetamide and the corresponding alkyl ethyl acetoacetates were synthesized according to modified literature procedures. The alkyl ethyl acetoacetates were obtained by the reaction of C-alkylation of ethyl acetoacetate. An investigation of the reaction conditions for the synthesis of 4-methyl-3-cyano-6-hydroxy-2-pyridone from cyanoacetamide and ethyl acetoacetate in eight different solvents was also performed. The ultraviolet absorption spectra of synthesized pyridones were measured in nine different solvents in the range 200–400 nm. The effects of solvent polarity and hydrogen bonding on the absorption spectra are interpreted by means of linear solvation energy relationships using a general equation of the form n = n0 + sp* + aa + bb, where p* is a measure of the solvent polarity, a is the scale of the solvent hydrogen bond donor acidities and b is the scale of the solvent hydrogen bond acceptor basicities.

Direct Production of Silicones From Sand

Energy Technology Data Exchange (ETDEWEB)

Larry N. Lewis; F.J. Schattenmann: J.P. Lemmon

2001-09-30

Silicon, in the form of silica and silicates, is the second most abundant element in the earth's crust. However the synthesis of silicones (scheme 1) and almost all organosilicon chemistry is only accessible through elemental silicon. Silicon dioxide (sand or quartz) is converted to chemical-grade elemental silicon in an energy intensive reduction process, a result of the exceptional thermodynamic stability of silica. Then, the silicon is reacted with methyl chloride to give a mixture of methylchlorosilanes catalyzed by cooper containing a variety of tract metals such as tin, zinc etc. The so-called direct process was first discovered at GE in 1940. The methylchlorosilanes are distilled to purify and separate the major reaction components, the most important of which is dimethyldichlorosilane. Polymerization of dimethyldichlorosilane by controlled hydrolysis results in the formation of silicone polymers. Worldwide, the silicones industry produces about 1.3 billion pounds of the basic silicon polymer, polydimethylsiloxane.

Graphene-Fiber-Based Supercapacitors Favor N-Methyl-2-pyrrolidone/Ethyl Acetate as the Spinning Solvent/Coagulant Combination.

Science.gov (United States)

He, Nanfei; Pan, Qin; Liu, Yixin; Gao, Wei

2017-07-26

One-dimensional flexible fiber supercapacitors (FSCs) have attracted great interest as promising energy-storage units that can be seamlessly incorporated into textiles via weaving, knitting, or braiding. The major challenges in this field are to develop tougher and more efficient FSCs with a relatively easy and scalable process. Here, we demonstrate a wet-spinning process to produce graphene oxide (GO) fibers from GO dispersions in N-methyl-2-pyrrolidone (NMP), with ethyl acetate as the coagulant. Upon chemical reduction of GO, the resulting NMP-based reduced GO (rGO) fibers (rGO@NMP-Fs) are twice as high in the surface area and toughness but comparable in tensile strength and conductivity as that of the water-based rGO fibers (rGO@H 2 O-Fs). When assembled into parallel FSCs, rGO@NMP-F-based supercapacitors (rGO@NMP-FSCs) offered a specific capacitance of 196.7 F cm -3 (147.5 mF cm -2 ), five times higher than that of rGO@H 2 O-F-based supercapacitors (rGO@H 2 O-FSCs) and also higher than most existing wet-spun rGO-FSCs, as well as those FSCs built with metal wires, graphene/carbon nanotube (CNT) fibers, or even pseudocapacitive materials. In addition, our rGO@NMP-FSCs can provide good bending and cycling stability. The energy density of our rGO@NMP-FSCs reaches ca. 6.8 mWh cm -3 , comparable to that of a Li thin-film battery (4 V/500 μAh).

DFT study on the adsorption of diethyl, ethyl methyl, and dimethyl ethers on the surface of gallium doped graphene

Energy Technology Data Exchange (ETDEWEB)

Shokuhi Rad, Ali, E-mail: a.shokuhi@gmail.com [Department of Chemical Engineering, Qaemshahr Branch, Islamic Azad University, Qaemshahr (Iran, Islamic Republic of); Sani, Emad; Binaeian, Ehsan [Department of Chemical Engineering, Qaemshahr Branch, Islamic Azad University, Qaemshahr (Iran, Islamic Republic of); Peyravi, Majid; Jahanshahi, Mohsen [Faculty of Chemical Engineering, Babol University of Technology, Babol (Iran, Islamic Republic of)

2017-04-15

Highlights: • Adsorption of three ether molecules on the surface of Ga-doped graphene has been investigated. • High degree of adsorption for all analytes is found. • Ga-doped graphene shows p-type semiconductor property upon adsorption of ether molecules. - Abstract: In this study, we used density functional theory (DFT) to search on the adsorption properties of three important compounds of ether family; diethyl ether (DEE), ethyl methyl ether (EME), and dimethyl ether (DME) on the surface of Gallium doped graphene (GaG). We used three functionals (B3LYP, wb97xd, and MPW1PW91) for optimization and calculation of adsorption energy. After fully optimization, we scrutinized on the charge allocations on the adsorbed ethers as well as GaG (at the area of interaction) based on natural bond orbitals (NBO). Besides, we have calculated the amount of charge transfer upon adsorption of each analyte. We revel that GaG is an ideal adsorbent for chemisorption of all above-mentioned ethers. There is a little difference between the values of adsorption; −123.5, −120, and −118.3 kJ/mol (based on wb97xd) for DEE, EME, and DME, respectively. We found significant changes in the electronic structure of both adsorbent and adsorbate upon adsorption. Moreover, results of charge analyses confirm GaG is a p-type semiconductor.

DFT study on the adsorption of diethyl, ethyl methyl, and dimethyl ethers on the surface of gallium doped graphene

International Nuclear Information System (INIS)

Shokuhi Rad, Ali; Sani, Emad; Binaeian, Ehsan; Peyravi, Majid; Jahanshahi, Mohsen

2017-01-01

Highlights: • Adsorption of three ether molecules on the surface of Ga-doped graphene has been investigated. • High degree of adsorption for all analytes is found. • Ga-doped graphene shows p-type semiconductor property upon adsorption of ether molecules. - Abstract: In this study, we used density functional theory (DFT) to search on the adsorption properties of three important compounds of ether family; diethyl ether (DEE), ethyl methyl ether (EME), and dimethyl ether (DME) on the surface of Gallium doped graphene (GaG). We used three functionals (B3LYP, wb97xd, and MPW1PW91) for optimization and calculation of adsorption energy. After fully optimization, we scrutinized on the charge allocations on the adsorbed ethers as well as GaG (at the area of interaction) based on natural bond orbitals (NBO). Besides, we have calculated the amount of charge transfer upon adsorption of each analyte. We revel that GaG is an ideal adsorbent for chemisorption of all above-mentioned ethers. There is a little difference between the values of adsorption; −123.5, −120, and −118.3 kJ/mol (based on wb97xd) for DEE, EME, and DME, respectively. We found significant changes in the electronic structure of both adsorbent and adsorbate upon adsorption. Moreover, results of charge analyses confirm GaG is a p-type semiconductor.

Anodic behavior of Mg in acidic AlCl3–1-ethyl-3-methyl-imidazolium chloride ionic liquid

International Nuclear Information System (INIS)

Xu, Bajin; Qu, Rui; Ling, Guoping

2014-01-01

Highlights: • A viscous layer formed at Mg/ionic liquid interface after the dissolution of Mg. • As direct evidence, photo of viscous layer at the interface was presented. • Viscous layer was resulted from accumulation of dissolved Mg(II) at interface. • Formation of viscous layer resulted in a homogenous etched Mg surface. • Dissolution model of Mg and formation mechanism of viscous layer was discussed. - Abstract: In this paper, anodic behavior of Mg in acidic AlCl 3 –1-ethyl-3-methyl-imidazolium chloride (AlCl 3 –EMIC) ionic liquid was investigated by conducting linear sweep voltammetry, chronoamperometry and chonopotentiometry. The viscosity of Mg dissolved ionic liquid and the surface morphologies of Mg were characterized using an Ostwald viscometer and a scanning electron microscopy, respectively. The results showed that the oxide film on the surface of Mg had great effects on the anodic behavior. The dissolution of Mg under anodic polarization occurred after the breakdown of oxide film. A viscous layer was observed forming at the interface of Mg/ionic liquid during the dissolution process. The formation of viscous layer was attributed to the accumulation of Mg dissolved AlCl 3 –EMIC ionic liquid at the interface, which was of high viscosity. With a viscous layer formed in the anodic process, the etched surface of Mg anode was homogeneous and flat without any etching pits. Otherwise, the Mg showed a morphology of pitting on the surface

Volumetric properties of ternary (IL + 2-propanol or 1-butanol or 2-butanol + ethyl acetate) systems and binary (IL + 2-propanol or 1-butanol or 2-butanol) and (1-butanol or 2-butanol + ethyl acetate) systems

International Nuclear Information System (INIS)

Bahadur, Indra; Deenadayalu, Nirmala; Tywabi, Zikhona; Sen, Sabyasachi; Hofman, Tadeusz

2012-01-01

Highlights: ► Experimental densities were determined at T = (298.15, 303.15, and 313.15) K. ► IL: methyl trioctylammonium bis(trifluoromethylsulfonyl)imide was used. ► Virial Based Mixing Rule correlation of the binary excess molar volume data. ► Binary excess molar volume was both negative and positive. ► Ternary excess molar volume data was correlated with the Cibulka equation. - Abstract: The experimental densities for the binary or ternary systems were determined at T = (298.15, 303.15, and 313.15) K. The ionic liquid methyl trioctylammonium bis(trifluoromethylsulfonyl)imide ([MOA] + [Tf 2 N] − ) was used for three of the five binary systems studied. The binary systems were ([MOA] + [Tf 2 N] − + 2-propanol or 1-butanol or 2-butanol) and (1-butanol or 2-butanol + ethyl acetate). The ternary systems were {methyl trioctylammonium bis(trifluoromethylsulfonyl)imide + 2-propanol or 1-butanol or 2-butanol + ethyl acetate}. The binary and ternary excess molar volumes for the above systems were calculated from the experimental density values for each temperature. The Redlich–Kister smoothing polynomial was fitted to the binary excess molar volume data. Virial-Based Mixing Rules were used to correlate the binary excess molar volume data. The binary excess molar volume results showed both negative and positive values over the entire composition range for all the temperatures. The ternary excess molar volume data were successfully correlated with the Cibulka equation using the Redlich–Kister binary parameters.

Synthesis, characterization and catalytic performance of mixed nanoferrites submitted to transesterification and esterification reaction using methyl and ethyl route for biodiesel production; Sintese, caracterizacao e performance catalitica de nanoferritas mistas submetidas a reacao de transesterificacao e esterificacao via rota metilica e etilica para biodiesel

Energy Technology Data Exchange (ETDEWEB)

Dantas, Joelda; Leal, Elvia; Mapossa, Antonio Benjamim; Silva, Adriano Sant' Ana; Costa, Ana Cristina Figueiredo de Melo, E-mail: joeldadantas@yahoo.com.br, E-mail: elvialeal@gmail.com, E-mail: mapossabenjox@gmail.com, E-mail: adriano_santana@yahoo.com.br, E-mail: ana.cristina@pq.cnpq.br [Universidade Federal de Campina Grande (LabSMaC/UAEMa/UFCG), PB (Brazil). Lab. de Sintese de Materiais Ceramicos

2016-10-15

The mixed nanoferrites of Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and Ni{sub 0.2}Cu{sub 0.3}Zn{sub 0.5}Fe{sub 2}O{sub 4} were synthesized by combustion reaction using urea as fuel and a conical reactor as heating source in batches of 10 g, and then tested as heterogeneous nanocatalysts in the transesterification and esterification reaction of soya bean oil using the methyl and ethyl routes to biodiesel production. During the synthesis the time and temperature of the reactions were measured, and the evolved gases and the color of the emitted flames were observed. The samples were characterized by XRD, EDX, FTIR, SEM/EDS, BET and gas chromatography. The reaction tests were carried out with 10 g of oil for 1 h, oil:alcohol molar ratio of 1:12, 2 % (w/w) of catalyst, and conducted at 180 °C. The XRD patterns and the FTIR spectra revealed the presence of the inverse spinel phase type B(AB){sub 2}O{sub 4}. The morphology showed the formation of agglomerates with fragile morphology and high surface area. The chromatographic analysis produced excellent results in the esterification reactions for both samples in the tested conditions, with special emphasis on Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4}, whose conversions were of 91.4 % in methyl esters and of 77.8 % in ethyl esters, while the Ni{sub 0.2}Cu{sub 0.3}Zn{sub 0.5}Fe{sub 2}O{sub 4} sample showed conversion of 75.1 and 65.1 %, respectively. The conversions in the methyl and ethyl transesterification were of 14 and 2 % of the Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} sample, and of 11 and 3 % for the Ni{sub 0.2}Cu{sub 0.3}Zn{sub 0.5}Fe{sub 2}O{sub 4} sample. (author)

Synthesis of ethyl [14CH3]methylmalonyl thioglycolate as a possible substrate analogue of [14CH3]methylmalonyl coenzyme-A

International Nuclear Information System (INIS)

Kovacs, I.; Kovacs, Z.

1991-01-01

Ethyl methylmalonyl thioglycolate is a potential substrate analogue of methylmalonyl-coenzyme-A (methylmalonyl-CoA) in the investigation of propionic acid metabolism. To prove this hypothesis, the tracer ethyl [ 14 CH 3 ] methylmalonyl thioglycolate was synthesized via methyl-Meldrum's acid to carry out the biochemical examinations. The method described can also be used to synthesize [ 14 CH 3 ] methylmalonyl-CoA by transesterification of active labelled methylmalonyl thiophenyl ester. This latter intermediate is chemically stable when stored at room temperature, and the unstable [ 14 CH 3 ]methylmalonyl-CoA can be prepared in one step just preceeding the biochemical experiments. (author)

Interação de glyphosate com carfentrazone-ethyl Glyphosate - carfentrazone-ethyl interaction

Directory of Open Access Journals (Sweden)

R.C. Werlang

2002-04-01

Full Text Available Foi conduzido um experimento em condições controladas para determinar a interação do carfentrazone-ethyl em mistura no tanque com o herbicida glyphosate, no controle de seis espécies de plantas daninhas. Glyphosate aplicado isoladamente na dose de 720 g ha-1 foi eficaz no controle de Amaranthus hybridus (100%, Desmodium tortuosum (100%, Bidens pilosa (99%, Eleusine indica (96%, Digitaria horizontalis (100% e Commelina benghalensis (93% aos 21 DAA. Carfentrazone-ethyl aplicado isoladamente controlou eficazmente C. benghalensis. As misturas de glyphosate nas doses de 252 e 720 g ha-1 com carfentrazone-ethyl nas doses de 15 e 30 g ha¹ demonstraram efeito aditivo no controle de A. hybridus, D. tortuosum e Bidens pilosa, à exceção das misturas de glyphosate na dose de 252 g ha-1 com as doses de 15 e 30 g ha-1 de carfentrazone-ethyl, que proporcionam efeito sinergístico no controle de D. tortuosum. A adição das duas doses de carfentrazone-ethyl antagonizou o efeito de glyphosate na menor dose (252 g ha-1 no controle de E. indica, apresentando, no entanto, efeito aditivo com o glyphosate na maior dose (720 g ha-1. Já para D. horizontalis, as misturas de carfentrazone-ethyl com glyphosate na menor dose (252 g ha-1 apresentaram efeito sinergístico no controle dessa espécie, demonstrando, ainda, efeito aditivo na mistura com glyphosate na dose de 720 g ha-1. A mistura de carfentrazone-ethyl com glyphosate proporcionou efeito aditivo no controle de C. benghalensis, independentemente das combinações de doses avaliadas. Os resultados deste experimento indicam que carfentrazone-ethyl apresenta comportamento diferenciado quanto à interação com glyphosate, dependendo da espécie de planta daninha e da dose dos herbicidas utilizados na mistura em tanque, sendo complementar na mistura em tanque com glyphosate, pois demonstrou efeito antagônico em poucas das combinações estudadas, prevalecendo seu efeito aditivo na mistura com glyphosate, no

Density, dynamic viscosity, and derived properties of binary mixtures of methanol or ethanol with water, ethyl acetate, and methyl acetate at T (293.15, 298.15, and 303.15) K

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, Begona; Calvar, Noelia; Gomez, Elena [Chemical Engineering Department, University of Vigo, 36200 Vigo (Spain); Dominguez, Angeles [Chemical Engineering Department, University of Vigo, 36200 Vigo (Spain)], E-mail: admguez@uvigo.es

2007-12-15

Densities and dynamic viscosities for methanol or ethanol with water, ethyl acetate, and methyl acetate at several temperatures T = (293.15, 298.15, and 303.15) K have been measured over the whole composition range and 0.1 MPa, along with the properties of the pure components. Excess molar volumes, viscosity deviations, and excess free energy of activation for the binary systems at the above-mentioned temperatures, were calculated and fitted to the Redlich-Kister equation to determine the fitting parameters and the root-mean-square deviations. UNIQUAC equation was used to correlate the experimental viscosity data. The UNIFAC-VISCO method and ASOG-VISCO method, based on contribution groups, were used to predict the dynamic viscosities of the binary mixtures.

Density, dynamic viscosity, and derived properties of binary mixtures of methanol or ethanol with water, ethyl acetate, and methyl acetate at T (293.15, 298.15, and 303.15) K

International Nuclear Information System (INIS)

Gonzalez, Begona; Calvar, Noelia; Gomez, Elena; Dominguez, Angeles

2007-01-01

Densities and dynamic viscosities for methanol or ethanol with water, ethyl acetate, and methyl acetate at several temperatures T = (293.15, 298.15, and 303.15) K have been measured over the whole composition range and 0.1 MPa, along with the properties of the pure components. Excess molar volumes, viscosity deviations, and excess free energy of activation for the binary systems at the above-mentioned temperatures, were calculated and fitted to the Redlich-Kister equation to determine the fitting parameters and the root-mean-square deviations. UNIQUAC equation was used to correlate the experimental viscosity data. The UNIFAC-VISCO method and ASOG-VISCO method, based on contribution groups, were used to predict the dynamic viscosities of the binary mixtures

Catalytic Ester to Stannane Functional Group Interconversion via Decarbonylative Cross-Coupling of Methyl Esters

KAUST Repository

Yue, Huifeng

2018-01-03

An unprecedented conversion of methyl esters to stannanes was realized, providing access to a series of arylstannanes via nickel catalysis. Various common esters including ethyl, cyclohexyl, benzyl, and phenyl esters can undergo the newly developed decarbonylative stannylation reaction. The reaction shows broad substrate scope, can differentiate between different types of esters, and if applied in consecutive fashion, allows the transformation of methyl esters into aryl fluorides or biaryls via fluororination or arylation.

Catalytic Ester to Stannane Functional Group Interconversion via Decarbonylative Cross-Coupling of Methyl Esters

KAUST Repository

Yue, Huifeng; Zhu, Chen; Rueping, Magnus

2018-01-01

An unprecedented conversion of methyl esters to stannanes was realized, providing access to a series of arylstannanes via nickel catalysis. Various common esters including ethyl, cyclohexyl, benzyl, and phenyl esters can undergo the newly developed decarbonylative stannylation reaction. The reaction shows broad substrate scope, can differentiate between different types of esters, and if applied in consecutive fashion, allows the transformation of methyl esters into aryl fluorides or biaryls via fluororination or arylation.

Energetic balance of castor oil methyl and ethyl esters; Balanco energetico de esteres metilicos e etilicos de oleo de mamona

Energy Technology Data Exchange (ETDEWEB)

Almeida Neto, Jose Adolfo de; Cruz, Rosenira Serpa da; Alves, Jaenes Miranda; Pires, Monica de Moura; Robra, Sabine [Universidade Estadual de Santa Cruz, Ilheus BA (Brazil). Grupo Bioenergia e Meio Ambiente]. E-mails: jalmeida@uesc.br; Parente Junior, Expedito [Tecnologias Bioenergeticas Ltda. (TECBIO), Fortaleza, CE (Brazil); Fundacao Nucleo de Tecnologia Industrial (NUTEC), Fortaleza, CE (Brazil)]. E-mail: expeditojr@tecbio.com.br

2004-07-01

Castor oil (Ricinus communis L.) is one of the cultures chosen by the biodiesel federal and state programs to supply raw material for biodiesel production - a biofuel indicated as renewable and less pollutant than its fossil competitor. An energetic balance was performed based on LCA - Life Cycle Analysis principles and Input-Output Analysis, comparing the castor oil energy performance with others traditional cultures: colza (Brassica napus) in Europe and soybean (Glycine max) in the United States. Energy balance (O-I) was positive in both production ways (methyl and ethyl) independent of coproduct use allocation alternative. The relation Output-Input (O-I) calculated for castor oil biodiesel [1.3-2.9] was higher than the colza (1.2-1.9) and lower than the soybean (3.2--3.4), independent of the way and allocation of the used byproduct. Both indicators suggest the energy and environmental viability of the castor oil biodiesel, provided that high agricultural productivity (higher than 1.500 kg/ha year) can be guaranteed. The potentialization of the positive energetic and environmental effects depends on the adequate utilization of the coproducts and process residues, the improvement of the energy efficiency in the the castor oil and biodiesel processing and the implementation of efficient management in the use of the chemical inputs (specially the N), responsible for up 5% of the total energy input.

Cobalt(ll) Coordination Compounds of Ethyl 4-Methyl-5-Imidazolecarboxylate: Chemical and Biochemical Characterization on Photosynthesis and Seed Germination

Science.gov (United States)

King-Díaz, Beatriz; Montes-Ayala, Josefina; Escartín-Guzmán, Concepción; Castillo-Blum, Silvia E.; Iglesias-Prieto, Roberto; Lotina-Hennsen, Blas; Barba-Behrens, Norah

2005-01-01

In this work we present the synthesis, structural and spectroscopic characterization of Co2+ coordination compounds with ethyl 4-methyl-5-imidazolecarboxylate (emizco). The effects of emizco, the metal salts CoCl2.6H2O, CoBr2, Co(NO3)2.6H2O and their metal coordination compounds [Co(emizco)2Cl2], [Co(emizco)2 Br2].H2O, [Co(emizco)2 (H2O)2(NO2)2.2H2O were evaluated on photosynthesis in spinach chloroplasts. Seed germination and seedling growth of the monocotyledonous species Lolium multiflorum and Triticum aestivum and the dicotyledonous species Trifolium alexandrinum and Physalis ixocarpa were also assayed under the effect of the compounds and salts. The results showed that cobalt(II) salts and their emizco coordination compounds inhibit photosynthetic electron flow and ATP-synthesis, behaving as Hill reaction inhibitors. Coordination compounds are more potent inhibitors than the salts. It was found that the salts target is at the b6f level while the complexes targets are at QB(D1)-protein and b6f level. The QB inhibition site was confirmed by variable chlorophyll a fluorescence yield. On the other hand, emizco inhibits seed germination, root and shoot development, in both weed and crop species. Cobalt(II) coordination compounds are the most effective photosynthesis inhibitors, but they are less potent than emizco in germination and seedling growth, while the metal salts are the least active of all. PMID:18365092

Vasodilatory effects and underlying mechanisms of the ethyl acetate extracts from Gastrodia elata.

Science.gov (United States)

Dai, Rong; Wang, Ting; Si, Xiaoqin; Jia, Yuanyuan; Wang, Lili; Yuan, Yan; Lin, Qing; Yang, Cui

2017-05-01

The objective of this study was to assess the ethyl acetate extracts of Gastrodia elata Blume (GEB) on vascular tone and the mechanisms involved. GEB was extracted with 95% EtOH followed by a further extraction with ethyl acetate. The effects of GEB and its ingredients on the isometric tensions of the aortic rings from rats were measured. The ethyl acetate extract of GEB induced a vasodilatory effect on rat aorta, which was partially dependent on endothelium. Four chemical compounds isolated from GEB were identified as 3,4-dihydroxybenzaldehyde (DB), 4-hydroxybenzaldehyde (HB), 4-methoxybenzyl alcohol (MA), and 4,4'-dihydroxydiphenyl methane (DM), respectively. All of these compounds induced vasodilatations, which were dependent on the endothelium to different degrees. After pretreatment with N ω -nitro-l-arginine methyl ester, indomethacin, or methylene blue, the vasodilatations induced by DB, HB, and MA were significantly decreased. In addition, the contractions of the rat aortic rings due to Ca 2+ influx and intracellular Ca 2+ release were also inhibited by DM. Furthermore, the administration of DB significantly enhanced the productions of nitric oxide (NO) and the activities of the endothelial NO synthase in aorta and in endothelial cells. Thus, GEB may play an important role in the amelioration of hypertension by modulating vascular tones.

IDENTIFICACIÓN DE ALGUNOS METABOLITOS SECUNDARIOS DEL EXTRACTO EN ACETATO DE ETILO DE Muricea sp.I IDENTIFICATION OF SOME SECONDARY METABOLITES FROM THE ETHYL- ACETATE-EXTRACT OF THE OCTOCORAL, Muricea sp.

Directory of Open Access Journals (Sweden)

Ángel Camacho

2018-04-01

Full Text Available Some chromatographic fractions obtained from the ethyl-acetate-extract of the unidentified octocoral species of the genus, Muricea , showed antibacterial activity against Escherichia coli , Salmonella enteritidis , Citrobacter freundii , Staphylococcus aureus , and Bacillus subtlis , which indicates the presence of bioactive compounds in it. The GC/MS analysis of some fractions obtained by continuous chromatographic separation, allowed identification of metabolites, such that: ( Z -9-octadecenoic acid methyl ester, octadecenoic acid methyl ester, 1-methyl-4-ethoxy-δ(3-pyrrolin-2-one, endo-1-bourbonanol, dibutylphtalate, 4,5-epoxy-1-isopropyl-4-methyl- 1-cyclohexene, 1,3,3-trimethyl-7-oxabcyclo[2.2.1]heptane-2-carboxylic acid ethyl ester, 2,6-dimethyl-2-trans- 6-octadiene, farnesol, 3β-cholesta-5,22-dien-3-ol, cholesterol, (3β,22 E ,24S-ergosta-5,22-dien-3-ol, (3β,5α-2- methylenecholestan-3-ol, 3-hidroxylongifolol, by comparison with the WILEY and NIST databases and the study of the fragmentation patterns of their mass spectra.

Synthesis, in vitro validation and in vivo pharmacokinetics of [{sup 125}I]N-[2-(4-iodophenyl)ethyl]-N-methyl-2-(1-piperidinyl) ethylamine: A high-affinity ligand for imaging sigma receptor positive tumors

Energy Technology Data Exchange (ETDEWEB)

John, Christy S; Gulden, Mary E; Vilner, Bertold J; Bowen, Wayne D

1996-08-01

N-[2-(4-iodophenyl)ethyl]-N-methyl-2-(1-piperidinyl)ethylamine, IPEMP, and the corresponding bromo derivative, BrPEMP, have been synthesized and characterized. Both BrPEMP and IPEMP were evaluated for sigma-1 and sigma-2 subtype receptor affinities and found to possess very high affinities for both receptor subtypes. The precursor for radioiodination n-tributylstannylphenylethylpiperidinylethylamine was prepared from its bromo derivative by palladium-catalyzed stannylation reaction. Radioiodinated 4-[{sup 125}I]PEMP was readily prepared in high yields and high specific activity by oxidative iododestannylation reaction using chloramine-T as oxidizing agent. Sites labeled by 4-[{sup 125}I]PEMP in guinea pig brain membranes showed high affinity for BD1008, haloperidol, and (+)-pentazocine (Ki = 5.06 {+-} 0.40, 32.6 {+-} 2.75, and 48.1 {+-} 8.60 nM, respectively), which is consistent with sigma receptor pharmacology. Competition binding studies of 4-[{sup 125}I]PEMP in melanoma (A375) and MCF-7 breast cancer cells showed a high affinity, dose-dependent inhibition of binding with known sigma ligand N-[2-(3,4-dichlorophenyl)ethyl]-N-methyl-2-(1-pyrrolidinyl) ethylamine, BD1008 (Ki = 5, 11 nM, respectively), supporting the labeling of sigma sites in these cells. Haloperidol, however showed a weaker (Ki 100-200 nM) affinity for the sites labeled by 4-[{sup 125}I]PEMP in these cells. Biodistribution studies of 4-[{sup 125}I]PEMP in rats showed a fast clearance of this radiopharmaceutical from blood, liver, lung, and other organs. A co-injection of 4-IPEMP with 4-[{sup 125}I]PEMP resulted in 37%, 69%, and 35% decrease in activity in liver, kidney, and brain (organs possessing sigma receptors), respectively at 1-h postinjection. These results suggest that 4-[{sup 125}I]PEMP is a promising radiopharmaceutical for pursuing further studies in animal models with tumors.

A Brillouin scattering study of the effect of chemical passivation on the elastic properties of porous silicon

Science.gov (United States)

Fan, H. J.; Kuok, M. H.; Ng, S. C.; Boukherroub, R.; Lockwood, D. J.

2002-07-01

Brillouin scattering has been performed to probe acoustic waves in porous silicon films that have been chemically modified with either 1-decene, decyl aldehyde, undecylenic acid, or ethyl undecylenate. The shift in the frequencies of acoustic modes in the passivated porous silicon samples, relative to those in freshly prepared porous silicon, is different for different chemical modifiers. The magnitude of the frequency shift is qualitatively correlated with the change, caused by the passivation, in the average densities and elastic constants of the samples.

Chromosomal analysis in mouse eggs fertilized in vitro with sperm exposed to ultraviolet light (UV) and methyl and ethyl methanesulfonate (MMS and EMS)

International Nuclear Information System (INIS)

Matsuda, Y.; Tobari, I.

1988-01-01

Chromosome aberrations were analyzed at the first-cleavage metaphase of mouse eggs fertilized in vitro with sperm exposed to ultraviolet light (UV) as well as to methyl and ethyl methanesulfonate (MMS and EMS). The frequencies of chromosome aberrations markedly increased with dose of UV as well as with concentration of MMS and EMS. In the UV-irradiation group, the frequency of chromosome-type aberrations was much higher than that of chromatid-type aberrations. About 90% of chromosome aberrations observed in the eggs following MMS and EMS treatment to sperm were chromosome type in which the frequency of chromosome fragments was the highest. The effects of UV on the induction of chromosome aberrations were clearly potentiated by post-treatment incubation of fertilized eggs in the presence of Ara-C or caffeine, but the effects of MMS and EMS were not pronounced by post-treatment of Ara-C or caffeine. The results indicate a possibility that UV damage induced in mouse sperm DNA is reparable in the eggs during the period between the entry of sperm into the egg cytoplasm and the first-cleavage metaphase. 35 refs.; 5 figs.; 4 tabs

Thermophysical study of methyl levulinate

International Nuclear Information System (INIS)

Lomba, Laura; Lafuente, Carlos; García-Mardones, Mónica; Gascón, Ignacio; Giner, Beatriz

2013-01-01

Highlights: • We have carried out a thermophysical characterization of methyl levulinate. • The study has been performed over a temperature range from (278.15 to 328.15) K. • pρT behavior has been studied over a temperature range from (333.15 to 453.15) K. • TRIDEN equation has been used to correlate pρT data. • Results have been compared with of ethyl and butyl levulinate and levulinic acid. -- Abstract: Several thermophysical properties (density, speed of sound, refractive index, surface tension, static permittivity and dynamic viscosity) of methyl levulinate have been measured under atmospheric pressure at temperatures from (278.15 to 338.15) K, while the vapor pressure was determined over a temperature range from (333.15 to 453.15) K. Furthermore, pρT behavior has been also investigated using a high-pressure, high-temperature vibrating tube densimeter over a temperature range from (283.15 to 338.15) K and a pressure range from (0.1 to 60.0) MPa. All these values obtained for methyl levulinate have been compared with other members of the levulinate family and also with levulinic acid

Study of the Transformation of the Oil of Used Soya in Fatty Acid Ethyl Ester

Directory of Open Access Journals (Sweden)

Anabel Sarracent-López

2016-07-01

Full Text Available The reuse of vegetable oils in food processing brings harmful health effects and on the other hand needs a complex treatment to discard without affecting the environment. Transformed into methyl or ethyl esters of fatty acids and glycerin by transesterification with the corresponding alcohol, can be a suitable method for treatment. It was investigated residual soybean oil from a producer of fried foods and ethanol. It is known that with this spirit the transformation process presents difficulties not listed with methanol, but at the same time does not bring the drawbacks of the latter, for toxicity and acquisition, and that since it is a derivative of the domestic sugar industry does not constitute a raw material import. We experimented with ethanol 80 %, 85 % and 90 % purity and worked 35 ºC and 50 ºC. Final yields of ethyl esters, are low compared with those obtained for similar processes with methanol, 85 % being the highest yield obtained under the conditions of the process. An assessment of costs was conducted to produce 1L of ethyl esters in the laboratory, the expenses of 0,56 pesos/L.

Bromidotetra?kis?(1H-2-ethyl-5-methyl?imidazole-?N 3)copper(II) bromide

OpenAIRE

Godlewska, Sylwia; Baranowska, Katarzyna; Socha, Joanna; Do??ga, Anna

2011-01-01

The CuII ion in the title compound, [CuBr(C6H10N2)4]Br, is coordinated in a square-based-pyramidal geometry by the N atoms of four imidazole ligands and a bromide anion in the apical site. Both the CuII and Br− atoms lie on a crystallographic fourfold axis. In the crystal, the [CuBr(C6H10N2)4]+ complex cations are linked to the uncoordinated Br− anions (site symmetry overline{4}) by N—H...Br hydrogen bonds, generating a three-dimensional network. The ethyl group ...

Stable electroluminescence from passivated nano-crystalline porous silicon using undecylenic acid

Science.gov (United States)

Gelloz, B.; Sano, H.; Boukherroub, R.; Wayner, D. D. M.; Lockwood, D. J.; Koshida, N.

2005-06-01

Stabilization of electroluminescence from nanocrystalline porous silicon diodes has been achieved by replacing silicon-hydrogen bonds terminating the surface of nanocrystalline silicon with more stable silicon-carbon (Si-C) bonds. Hydrosilylation of the surface of partially and anodically oxidized porous silicon samples was thermally induced at about 90 °C using various different organic molecules. Devices whose surface have been modified with stable covalent bonds shows no degradation in the EL efficiency and EL output intensity under DC operation for several hours. The enhanced stability can be attributed to the high chemical resistance of Si-C bonds against current-induced surface oxidation associated with the generation of nonradiative defects. Although devices treated with 1-decene exhibit reduced EL efficiency and brightness compared to untreatred devices, other molecules, such as ethyl-undecylenate and particularly undecylenic acid provide stable and more efficient visible electroluminescence at room temperature. Undecylenic acid provides EL brightness as high as that of an untreated device.

Experimental and Kinetic Modeling Study of Ethyl Levulinate Oxidation in a Jet-Stirred Reactor

KAUST Repository

Wang, Jui-Yang

2017-06-01

A jet-stirred reactor was designed and constructed in the Clean Combustion Research Center (CCRC) at King Abdullah University of Science and Technology (KAUST); was validated with n-heptane, iso-octane oxidation and cyclohexene pyrolysis. Different configurations of the setup have been tested to achieve good agreement with results from the literature. Test results of the reactor indicated that installation of a pumping system at the downstream side in the experimental apparatus was necessary to avoid the reoccurrence of reactions in the sampling probe. Experiments in ethyl levulinate oxidation were conducted in the reactor under several equivalence ratios, from 600 to 1000 K, 1 bar and 2 s residence time. Oxygenated species detected included methyl vinyl ketone, levulinic acid and ethyl acrylate. Ethylene, methane, carbon monoxide, hydrogen, oxygen and carbon dioxide were further quantified with a gas chromatography, coupled with a flame ionization detector and a thermal conductivity detector. The ethyl levulinate chemical kinetic model was first developed by Dr. Stephen Dooley, Trinity College Dublin, and simulated under the same conditions, using the Perfect-Stirred Reactor code in Chemkin software. In comparing the simulation results with experimental data, some discrepancies were noted; predictions of ethylene production were not well matched. The kinetic model was improved by updating several classes of reactions: unimolecular decomposition, H-abstraction, C-C and C-O beta-scissions of fuel radicals. The updated model was then compared again with experimental results and good agreement was achieved, proving that the concerted eliminated reaction is crucial for the kinetic mechanism formulation of ethyl levulinate. In addition, primary reaction pathways and sensitivity analysis were performed to describe the role of molecular structure in combustion (800 and 1000 K for ethyl levulinate oxidation in the jet-stirred reactor).

Age-Related DNA Methylation Changes and Neoplastic Transformation of the Human Prostate

Science.gov (United States)

2009-07-01

associated CpG island to be d ifferentially hyp ermethylated in th e L NCaP cell line and 25 unique promoter associated CpG island s to b e dif ferentially h...ypomethylated in the L NCaP cell line . Several of these differentially m ethylated genes have been previously reported. Novel methylated genes of

2-(5-Fluoro-3-isopropylsulfanyl-7-methyl-1-benzofuran-2-ylacetic acid

Directory of Open Access Journals (Sweden)

Hong Dae Choi

2012-04-01

Full Text Available The title compound, C14H15FO3S, was prepared by alkaline hydrolysis of ethyl 2-(5-fluoro-3-isopropylsulfanyl-7-methyl-1-benzofuran-2-ylacetate. In the crystal, molecules are linked via pairs of O—H...O hydrogen bonds, forming inversion dimers. These dimers are connected by weak C—H...O hydrogen bonds.

Photodegradation of ethyl paraben using simulated solar radiation and Ag{sub 3}PO{sub 4} photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Frontistis, Zacharias [Department of Chemical Engineering, University of Patras, Caratheodory 1, University Campus, GR-26504 Patras (Greece); Antonopoulou, Maria [Department of Environmental & Natural Resources Management, University of Patras, 2 Seferi St., GR-30100 Agrinio (Greece); Petala, Athanasia [Department of Chemical Engineering, University of Patras, Caratheodory 1, University Campus, GR-26504 Patras (Greece); Venieri, Danae [School of Environmental Engineering, Technical University of Crete, Polytechneioupolis, GR-73100 Chania (Greece); Konstantinou, Ioannis [Department of Environmental & Natural Resources Management, University of Patras, 2 Seferi St., GR-30100 Agrinio (Greece); Department of Chemistry, University of Ioannina, GR-45110 Ioannina (Greece); Kondarides, Dimitris I. [Department of Chemical Engineering, University of Patras, Caratheodory 1, University Campus, GR-26504 Patras (Greece); Mantzavinos, Dionissios, E-mail: mantzavinos@chemeng.upatras.gr [Department of Chemical Engineering, University of Patras, Caratheodory 1, University Campus, GR-26504 Patras (Greece)

2017-02-05

Highlights: • Ag{sub 3}PO{sub 4} with a bandgap of 2.4 eV is a photocatalyst highly responsive to visible. • Factorial design was used to assess important factors for ethyl paraben degradation. • Ethyl paraben and Ag{sub 3}PO{sub 4} concentration, time, water matrix are significant factors. • Dealkylated and decarboxylated transformation by-products have been identified. • All parabens are slightly estrogenic compared to estradiol. - Abstract: In this work, the solar light-induced photocatalytic degradation of ethyl paraben (EP), a representative of the parabens family, was studied using silver orthophosphate, a relatively new photocatalytic material. The catalyst was synthesized by a precipitation method and had a primary crystallite size of ca 70 nm, specific surface area of 1.4 m{sup 2}/g and a bandgap of 2.4 eV. A factorial design methodology was implemented to evaluate the importance of EP concentration (500–1500 μg/L), catalyst concentration (100–500 mg/L), reaction time (4–30 min), water matrix (pure water or 10 mg/L humic acid) and initial solution pH (3–9) on EP removal. All individual effects but solution pH were statistically significant and so were the second-order interactions of EP concentration with reaction time or catalyst concentration. The water matrix effect was negative (all other effects were positive) signifying the role of humic acid as scavenger of the oxidant species. Liquid chromatography-time of flight mass spectrometry revealed the formation of methyl paraben, 4-hydroxybenzoic acid, benzoic acid and phenol as primary transformation by-products; these are formed through dealkylation and decarboxylation reactions initiated primarily by the photogenerated holes. Estrogenicity assays showed that methyl paraben was more estrogenic than EP; however, parabens are slightly estrogenic compared to 17β-estradiol.

49 CFR 173.322 - Ethyl chloride.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Ethyl chloride. 173.322 Section 173.322 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.322 Ethyl chloride. Ethyl chloride must be...

Evaluation of Poly(2-Ethyl-2-Oxazoline) Containing Copolymer Networks of Varied Composition as Sustained Metoprolol Tartrate Delivery Systems

OpenAIRE

Kostova, Bistra; Ivanova, Sijka; Balashev, Konstantin; Rachev, Dimitar; Christova, Darinka

2014-01-01

Segmented copolymer networks (SCN) based on poly(2-ethyl-2-oxazoline) and containing 2-hydroxyethyl methacrylate, 2-hydroxypropyl acrylate, and/or methyl methacrylate segments have been evaluated as potential sustained release systems of the water soluble cardioselective β-blocker metoprolol tartrate. The structure and properties of the drug carriers were investigated by differential scanning calorimetry, attenuated total reflectance Fourier transform infrared spectroscopy, scanning electron ...

Blockade of N-methyl-D-aspartate induced convulsions by 1-aminocyclopropanecarboxylates

International Nuclear Information System (INIS)

Skolnick, P.; Marvizon, J.C.G.; Jackson, B.W.; Monn, J.A.; Rice, K.C.; Lewin, A.H.

1989-01-01

1-Aminocyclopropanecarboxylic acid is a potent and selective ligand for the glycine modulatory site on the N-methyl-D-aspartate receptor complex. This compound blocks the convulsions and deaths produced by N-methyl-D-aspartate in a dose dependent fashion. In contrast, 1-aminocyclopropanecarboxylic acid does not protect mice against convulsions induced by pentylenetetrazole, strychnine, bicuculline, or maximal electroshock, and does not impair motor performance on either a rotarod or horizontal wire at doses of up to 2 g/kg. The methyl- and ethyl- esters of 1-aminocyclopropanecarboxylic acid are 5- and 2.3-fold more potent, respectively, than the parent compound in blocking the convulsant and lethal effects of N-methyl-D-aspartate. However, these esters are several orders of magnitude less potent than 1-aminocyclopropanecarboxylic acid as inhibitors of strychnine-insensitive [ 3 H]glycine binding, indicating that conversion to the parent compound may be required to elicit an anticonvulsant action

Comparative analysis of skin sensitization potency of acrylates (methyl acrylate, ethyl acrylate, butyl acrylate, and ethylhexyl acrylate) using the local lymph node assay.

Science.gov (United States)

Dearman, Rebecca J; Betts, Catherine J; Farr, Craig; McLaughlin, James; Berdasco, Nancy; Wiench, Karin; Kimber, Ian

2007-10-01

There are currently available no systematic experimental data on the skin sensitizing properties of acrylates that are of relevance in occupational settings. Limited information from previous guinea-pig tests or from the local lymph node assay (LLNA) is available; however, these data are incomplete and somewhat contradictory. For those reasons, we have examined in the LLNA 4 acrylates: butyl acrylate (BA), ethyl acrylate (EA), methyl acrylate (MA), and ethylhexyl acrylate (EHA). The LLNA data indicated that all 4 compounds have some potential to cause skin sensitization. In addition, the relative potencies of these acrylates were measured by derivation from LLNA dose-response analyses of EC3 values (the effective concentration of chemical required to induce a threefold increase in proliferation of draining lymph node cells compared with control values). On the basis of 1 scheme for the categorization of skin sensitization potency, BA, EA, and MA were each classified as weak sensitizers. Using the same scheme, EHA was considered a moderate sensitizer. However, it must be emphasized that the EC3 value for this chemical of 9.7% is on the borderline between moderate (10%) categories. Thus, the judicious view is that all 4 chemicals possess relatively weak skin sensitizing potential.

Accelerated living cationic ring-opening polymerization of a methyl ester functionalized 2-oxazoline monomer

NARCIS (Netherlands)

Bouten, P.J.M.; Hertsen, D.; Vergaelen, M.; Monnery, B.D.; Boerman, M.A.; Goossens, H.; Catak, S.; van Hest, J.C.M.; van Speybroeck, Veronique; Hoogenboom, Richard

2015-01-01

Kinetic studies on the homo- and copolymerization of 2-methoxycarboxyethyl-2-oxazoline (MestOx) with 2-methyl-2-oxazoline (MeOx) and 2-ethyl-2-oxazoline (EtOx) were performed. For the homopolymerisation of MestOx an increased propagation rate constant was observed compared to MeOx and EtOx while the

Poly(methyl vinyl ether-alt-maleic acid)-functionalized porous silicon nanoparticles for enhanced stability and cellular internalization.

Science.gov (United States)

Shahbazi, Mohammad-Ali; Almeida, Patrick V; Mäkilä, Ermei; Correia, Alexandra; Ferreira, Mónica P A; Kaasalainen, Martti; Salonen, Jarno; Hirvonen, Jouni; Santos, Hélder A

2014-03-01

Currently, developing a stable nanocarrier with high cellular internalization and low toxicity is a key bottleneck in nanomedicine. Here, we have developed a successful method to covalently conjugate poly(methyl vinyl ether-co-maleic acid) (PMVE-MA) copolymer on the surface of (3-aminopropyl)triethoxysilane-functionalized thermally carbonized porous silicon nanoparticles (APSTCPSi NPs), forming a surface negatively charged nanovehicle with unique properties. This polymer conjugated NPs could modify surface smoothness, charge, and hydrophilicity of the developed NPs, leading to considerable improvement in the colloidal and plasma stabilities via enhanced suspensibility and charge repulsion. Furthermore, despite the surface negative charge of the polymer-conjugated NPs, the cellular internalization was increased in both MDA-MB-231 and MCF-7 breast cancer cells. These results provide a proof-of-concept evidence that such polymer-based PSi nanocomposite can be extensively used as a promising candidate for intracellular drug delivery. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

21 CFR 573.420 - Ethyl cellulose.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ethyl cellulose. 573.420 Section 573.420 Food and... Listing § 573.420 Ethyl cellulose. The food additive ethyl cellulose may be safely used in animal feed in accordance with the following prescribed conditions: (a) The food additive is a cellulose ether containing...

21 CFR 172.868 - Ethyl cellulose.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethyl cellulose. 172.868 Section 172.868 Food and... Multipurpose Additives § 172.868 Ethyl cellulose. The food additive ethyl cellulose may be safely used in food in accordance with the following prescribed conditions: (a) The food additive is a cellulose ether...

Biology-oriented drug synthesis (BIODS) of 2-(2-methyl-5-nitro-1H-imidazol-1-yl)ethyl aryl ether derivatives, in vitro α-amylase inhibitory activity and in silico studies.

Science.gov (United States)

Taha, Muhammad; Imran, Syahrul; Ismail, Nor Hadiani; Selvaraj, Manikandan; Rahim, Fazal; Chigurupati, Sridevi; Ullah, Hayat; Khan, Fahad; Salar, Uzma; Javid, Muhammad Tariq; Vijayabalan, Shantini; Zaman, Khalid; Khan, Khalid Mohammed

2017-10-01

A new library of 2-(2-methyl-5-nitro-1H-imidazol-1-yl)ethyl aryl ether derivatives (1-23) were synthesized and characterized by EI-MS and 1 H NMR, and screened for their α-amylase inhibitory activity. Out of twenty-three derivatives, two molecules 19 (IC 50 =0.38±0.82µM) and 23 (IC 50 =1.66±0.14µM), showed excellent activity whereas the remaining compounds, except 10 and 17, showed good to moderate inhibition in the range of IC 50 =1.77-2.98µM when compared with the standard acarbose (IC 50 =1.66±0.1µM). A plausible structure-activity relationship has also been presented. In addition, in silico studies was carried out in order to rationalize the binding interaction of compounds with the active site of enzyme. Copyright © 2017 Elsevier Inc. All rights reserved.

Spectral Analysis of 3-(Adamantan-1-yl)-4-Ethyl-1-[(4-Phenylpiperazin-1-yl) Methyl]-1 H-1,2,4-Triazole-5(4 H)-Thione

Science.gov (United States)

Mindarava, Y. L.; Shundalau, M. B.; Al-Wahaibi, L. H.; El-Emam, A. A.; Matsukovich, A. S.; Gaponenko, S. V.

2018-05-01

Vibrational IR (3200-650 cm-1) and Raman spectra (3200-150 cm-1) of adamantane-containing 3-(adamantan-1-yl)-4-ethyl-1-[(4-phenylpiperazin-1-yl)methyl]-1H-1,2,4-triazole-5(4H)-thione, which is promising for drug design, were examined. The UV/Vis spectrum (450-200 nm) of the compound in EtOH was measured. Full geometry optimization using density functional theory (DFT) in the B3LYP/cc-pVDZ approximation allowed the equilibrium configuration of the molecule to be determined and IR and Raman spectra to be calculated. Based on these, the experimental vibrational IR and Raman spectra were interpreted and the biological activity indices were predicted. The UV/Vis spectrum of the title compound was simulated at the time-dependent DFT/CAM-B3LYP/cc-pVDZ level with and without solvent effects and at the ab initio multi-reference perturbation theory XMCQDPT2 level. The UV/Vis spectrum that was simulated using the multi-reference XMCQDPT2 approximation agreed very successfully with the experimental data, in contrast to the single-reference DFT method. This was probably a consequence of intramolecular charge transfer.

Spectral Analysis of 3-(Adamantan-1-yl)-4-Ethyl-1-[(4-Phenylpiperazin-1-yl) Methyl]-1H-1,2,4-Triazole-5(4H)-Thione

Science.gov (United States)

Mindarava, Y. L.; Shundalau, M. B.; Al-Wahaibi, L. H.; El-Emam, A. A.; Matsukovich, A. S.; Gaponenko, S. V.

2018-05-01

Vibrational IR (3200-650 cm-1) and Raman spectra (3200-150 cm-1) of adamantane-containing 3-(adamantan-1-yl)-4-ethyl-1-[(4-phenylpiperazin-1-yl)methyl]-1H-1,2,4-triazole-5(4H)-thione, which is promising for drug design, were examined. The UV/Vis spectrum (450-200 nm) of the compound in EtOH was measured. Full geometry optimization using density functional theory (DFT) in the B3LYP/cc-pVDZ approximation allowed the equilibrium configuration of the molecule to be determined and IR and Raman spectra to be calculated. Based on these, the experimental vibrational IR and Raman spectra were interpreted and the biological activity indices were predicted. The UV/Vis spectrum of the title compound was simulated at the time-dependent DFT/CAM-B3LYP/cc-pVDZ level with and without solvent effects and at the ab initio multi-reference perturbation theory XMCQDPT2 level. The UV/Vis spectrum that was simulated using the multi-reference XMCQDPT2 approximation agreed very successfully with the experimental data, in contrast to the single-reference DFT method. This was probably a consequence of intramolecular charge transfer.

Stable electroluminescence from passivated nano-crystalline porous silicon using undecylenic acid

Energy Technology Data Exchange (ETDEWEB)

Gelloz, B.; Sano, H.; Koshida, N. [Dept. Elec. and Elec. Eng., Tokyo Univ. of A and T, Koganei, Tokyo 184-8588 (Japan); Boukherroub, R. [Laboratoire de Physique de la Matiere Condensee, Ecole Polytechnique, Route de Saclay, 91128 Palaiseau (France); Wayner, D.D.M.; Lockwood, D.J. [National Research Council, Ottawa (Canada)

2005-06-01

Stabilization of electroluminescence from nanocrystalline porous silicon diodes has been achieved by replacing silicon-hydrogen bonds terminating the surface of nanocrystalline silicon with more stable silicon-carbon (Si-C) bonds. Hydrosilylation of the surface of partially and anodically oxidized porous silicon samples was thermally induced at about 90 C using various different organic molecules. Devices whose surface have been modified with stable covalent bonds shows no degradation in the EL efficiency and EL output intensity under DC operation for several hours. The enhanced stability can be attributed to the high chemical resistance of Si-C bonds against current-induced surface oxidation associated with the generation of nonradiative defects. Although devices treated with 1-decene exhibit reduced EL efficiency and brightness compared to untreated devices, other molecules, such as ethyl-undecylenate and particularly undecylenic acid provide stable and more efficient visible electroluminescence at room temperature. Undecylenic acid provides EL brightness as high as that of an untreated device. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Volumetric properties of room temperature ionic liquid 1. The system of {l_brace}1-methyl-3-ethylimidazolium ethyl sulfate+water{r_brace} at temperature in the range (278.15 to 333.15) K

Energy Technology Data Exchange (ETDEWEB)

Lu Xingmei [Department of Chemistry, Shenyang Normal University, Shenyang 110034 (China); Department of Chemistry, Liaoning University, Shenyang 110036 (China); Xu Weiguo [Institute of Salt Lakes, Chinese Academy of Science, Xining 810008 (China); Gui Jinsong [Department of Chemistry, Shenyang Normal University, Shenyang 110034 (China); Li Huawei [Department of Chemistry, Shenyang Normal University, Shenyang 110034 (China); Yang Jiazhen [Institute of Salt Lakes, Chinese Academy of Science, Xining 810008 (China)]. E-mail: jzyanglnu@yahoo.com.cn

2005-01-01

This paper reports densities of aqueous solutions of ionic liquid (IL) 1-methyl-3-ethylimidazolium ethyl sulfate (EMISE) that were measured gravimetrically at temperatures (278.15 to 333.15) K. The values of the apparent molar volume, {sup {phi}}V{sub B} and partial molar volume, V-bar B, were determined and apparent molar expansibilities {sup {phi}}E=(({partial_derivative}{phi}{sub B})/{partial_derivative}T)){sub p} of EMISE and the coefficients of thermal expansion of the solutions, {alpha}, were calculated. The values of the apparent molar volume, {sup {phi}}V{sub B}, were fitted by the method of least-squares to a Pitzer's equation to determine the parameters, {beta}{sub MX}{sup (0)V}, {beta}{sub MX}{sup (1)V}, and C{sub MX}{sup V}.

Synthesis of ethyl ( sup 14 CH sub 3 )methylmalonyl thioglycolate as a possible substrate analogue of ( sup 14 CH sub 3 )methylmalonyl coenzyme-A

Energy Technology Data Exchange (ETDEWEB)

Kovacs, I. (BIOGAL Pharmaceutical Works, Debrecen (Hungary)); Kovacs, Z. (Inst. of Nuclear Research, Debrecen (Hungary))

1991-11-01

Ethyl methylmalonyl thioglycolate is a potential substrate analogue of methylmalonyl-coenzyme-A (methylmalonyl-CoA) in the investigation of propionic acid metabolism. To prove this hypothesis, the tracer ethyl ({sup 14}CH{sub 3}) methylmalonyl thioglycolate was synthesized via methyl-Meldrum's acid to carry out the biochemical examinations. The method described can also be used to synthesize ({sup 14}CH{sub 3}) methylmalonyl-CoA by transesterification of active labelled methylmalonyl thiophenyl ester. This latter intermediate is chemically stable when stored at room temperature, and the unstable ({sup 14}CH{sub 3})methylmalonyl-CoA can be prepared in one step just preceeding the biochemical experiments. (author).

Lifetime Analysis of Rubber Gasket Composed of Methyl Vinyl Silicone Rubber with Low-Temperature Resistance

Directory of Open Access Journals (Sweden)

Young-Doo Kwon

2015-01-01

Full Text Available Most machines and instruments constantly require elastomeric materials like rubber for the purposes of shock absorption, noise attenuation, and sealing. The material properties and accurate lifetime prediction of rubber are closely related to the quality of machines, especially their durability and reliability. The properties of rubber-like elastomers are influenced by ambient conditions, such as temperature, environment, and mechanical load. Moreover, the initial properties of rubber gaskets must be sustained under working conditions to satisfy their required function. Because of its technical merits, as well as its low cost, the highly accelerated life test (HALT is used by many researchers to predict the long-term lifetime of rubber materials. Methyl vinyl silicone rubber (VMQ has recently been adopted to improve the lifetime of automobile radiator gaskets. A four-parameter method of determining the recovery ability of the gaskets was recently published, and two revised methods of obtaining the recovery were proposed for polyacrylate (ACM rubber. The recovery rate curves for VMQ were acquired using the successive zooming genetic algorithm (SZGA. The gasket lifetime for the target recovery (60% of a compressed gasket was computed somewhat differently depending on the selected regression model.

Continuous hydrogenation of ethyl levulinate to γ-valerolactone and 2-methyl tetrahydrofuran over alumina doped Cu/SiO2 catalyst: the potential of commercialization

Science.gov (United States)

Zheng, Junlin; Zhu, Junhua; Xu, Xuan; Wang, Wanmin; Li, Jiwen; Zhao, Yan; Tang, Kangjian; Song, Qi; Qi, Xiaolan; Kong, Dejin; Tang, Yi

2016-01-01

Hydrogenation of levulinic acid (LA) and its esters to produce γ-valerolactone (GVL) and 2-methyl tetrahydrofuran (2-MTHF) is a key step for the utilization of cellulose derived LA. Aiming to develop a commercially feasible base metal catalyst for the production of GVL from LA, with satisfactory activity, selectivity, and stability, Al2O3 doped Cu/SiO2 and Cu/SiO2 catalysts were fabricated by co-precipitation routes in parallel. The diverse physio-chemical properties of these two catalysts were characterized by XRD, TEM, dissociative N2O chemisorptions, and Py-IR methods. The catalytic properties of these two catalysts were systematically assessed in the continuous hydrogenation of ethyl levulinate (EL) in a fixed-bed reactor. The effect of acidic property of the SiO2 substrate on the catalytic properties was investigated. To justify the potential of its commercialization, significant attention was paid on the initial activity, proper operation window, by-products control, selectivity, and stability of the catalyst. The effect of reaction conditions, such as temperature and pressure, on the performance of the catalyst was also thoroughly studied. The development of alumina doped Cu/SiO2 catalyst strengthened the value-chain from cellulose to industrially important chemicals via LA and GVL. PMID:27377401

Solid acid catalysed formation of ethyl levulinate and ethyl glucopyranoside from mono- and disaccharides

DEFF Research Database (Denmark)

Shunmugavel, Saravanamurugan; Riisager, Anders

2012-01-01

Sulfonic acid functionalised SBA-15 (SO3H-SBA-15), sulfated zirconia and beta, Y, ZSM-5 and mordenite zeolite catalysts have been applied for the dehydration of sugars to ethyl levulinate and ethyl-D-glucopyranoside (EDGP) using ethanol as solvent and reactant. The SO3H-SBA-15 catalyst showed...

Transesterification of Vegetable Oils with Ethanol and Characterization of the Key Fuel Properties of Ethyl Esters

Directory of Open Access Journals (Sweden)

Stamoulis Stournas

2009-06-01

Full Text Available The transesterification reactions of four different vegetable oils (sunflower, rapeseed, olive oil and used frying oil with ethanol, using sodium hydroxide as catalyst, were studied. The ester preparation involved a two-step transesterification reaction, followed by purification. The effects of the mass ratio of catalyst to oil (0.25 – 1.5%, the molar ratio of ethanol to oil (6:1 – 12:1, and the reaction temperature (35 – 90 °C were studied for the conversion of sunflower oil to optimize the reaction conditions in both stages. The rest of the vegetable oils were converted to ethyl esters under optimum reaction parameters. The optimal conditions for first stage transesterification were an ethanol/oil molar ratio of 12:1, NaOH amount (1% wt/wt, and 80 °C temperature, whereas the maximum yield of ethyl esters reached 81.4% wt/wt. In the second stage, the yield of ethyl esters was improved by 16% in relation with the one-stage transesterification, which was obtained under the following optimal conditions: catalyst concentration 0.75% and ethanol/oil molar ratio 6:1. The fuel properties of the esters were measured according to EN test methods. Based on the experimental results one can see that the ethyl esters do not differ significantly from methyl esters. Moreover, the results showed that the values of density, viscosity, and higher heating value of ethyl esters were similar to those of automotive and heavy duty engine diesel fuel. However, the CFPP values were higher, which may contribute to potential difficulties in cold starts. On the other hand, the flash points, which were higher than those of diesel fuel constituted a safety guarantee from the point of view of handling and storage.

Ethyl methanesulfonate mutagenesis in Schizosaccharomyces pombe

DEFF Research Database (Denmark)

Ekwall, Karl; Thon, Genevieve

2017-01-01

Here we provide an ethyl methanesulfonate (EMS) mutagenesis protocol for Schizosaccharomyces pombe cells.......Here we provide an ethyl methanesulfonate (EMS) mutagenesis protocol for Schizosaccharomyces pombe cells....

Hydroxide as general base in the saponification of ethyl acetate.

Science.gov (United States)

Mata-Segreda, Julio F

2002-03-13

The second-order rate constant for the saponification of ethyl acetate at 30.0 degrees C in H(2)O/D(2)O mixtures of deuterium atom fraction n (a proton inventory experiment) obeys the relation k(2)(n) = 0.122 s(-1) M(-1) (1 - n + 1.2n) (1 - n + 0.48n)/(1 - n + 1.4n) (1 - n + 0.68n)(3). This result is interpreted as a process where formation of the tetrahedral intermediate is the rate-determining step and the transition-state complex is formed via nucleophilic interaction of a water molecule with general-base assistance from hydroxide ion, opposite to the direct nucleophilic collision commonly accepted. This mechanistic picture agrees with previous heavy-atom kinetic isotope effect data of Marlier on the alkaline hydrolysis of methyl formate.

Continuous realtime radioiodine monitor employing on-line methyl iodide conversion

International Nuclear Information System (INIS)

Fernandez, S.J.; Motes, B.G.

1980-01-01

An integrated 14 C, 129 I, and 85 Kr monitor was proposed by Fernandez, et al. that separates 129 I from 85 Kr by selective permeation across thin silicone rubber membranes. Subsequent studies of the permeation of CH 3 I and I 2 through silicone rubber membranes demonstrated that I 2 transport across the membranes is too slow to be useful in a realtime monitor. Transport of methyl iodide, however, is rapid and gives a separation factor of greater than 100 from 85 Kr

Iron halide mediated atom transfer radical polymerization of methyl methacrylate with N-Alkyl-2-pyridylmethanimine as the ligand

NARCIS (Netherlands)

Zhang, H.; Schubert, U.S.

2004-01-01

The controlled atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) catalyzed by iron halide/N-(n-hexyl)-2-pyridylmethanimine (NHPMI) is described. The ethyl 2-bromoisobutyrate (EBIB)-initiated ATRP with [MMA]0/[EBIB]0/[iron halide]0/[NHPMI]0 = 150/1/1/2 was better controlled in

The combustion kinetics of the lignocellulosic biofuel, ethyl levulinate

KAUST Repository

Ghosh, Manik Kumer; Howard, Mí cheá l Sé amus; Zhang, Yingjia; Djebbi, Khalil; Capriolo, Gianluca; Farooq, Aamir; Curran, Henry J.; Dooley, Stephen

2018-01-01

Ethyl levulinate (Ethyl 4-oxopentanoate) is a liquid molecule at ambient temperature, comprising of ketone and ethyl ester functionalities and is one of the prominent liquid fuel candidates that may be easily obtained from lignocellulosic biomass. The combustion kinetics of ethyl levulinate have been investigated. Shock tube and rapid compression machine apparatuses are utilised to acquire gas phase ignition delay measurements of 0.5% ethyl levulinate/O2 mixtures at ϕ = 1.0 and ϕ = 0.5 at ∼ 10 atm over the temperature range 1000–1400 K. Ethyl levulinate is observed not to ignite at temperatures lower than ∼1040 K in the rapid compression machine. The shock tube and rapid compression machine data are closely consistent and show ethyl levulinate ignition delay to exhibit an Arrhenius dependence to temperature. These measurements are explained by the construction and analysis of a detailed chemical kinetic model. The kinetic model is completed by establishing thermochemical-kinetic analogies to 2-butanone, for the ethyl levulinate ketone functionality, and to ethyl propanoate for the ethyl ester functionality. The so constructed model is observed to describe the shock tube data very accurately, but computes the rapid compression machine data set to a lesser but still applicable fidelity. Analysis of the model suggests the autooxidation mechanism of ethyl levulinate to be entirely dominated by the propensity for the ethyl ester functionality to unimolecularly decompose to form levulinic acid and ethylene. The subsequent reaction kinetics of these species is shown to dictate the overall rate of the global combustion reaction. This model is then use to estimate the Research and Motored Octane Numbers of ethyl levulinate to be ≥97.7 and ≥ 93, respectively. With this analysis ethyl levulinate would be best suited as a gasoline fuel component, rather than as a diesel fuel as suggested in the literature. Indeed it may be considered to be useful as an

The combustion kinetics of the lignocellulosic biofuel, ethyl levulinate

KAUST Repository

Ghosh, Manik Kumer

2018-04-04

Ethyl levulinate (Ethyl 4-oxopentanoate) is a liquid molecule at ambient temperature, comprising of ketone and ethyl ester functionalities and is one of the prominent liquid fuel candidates that may be easily obtained from lignocellulosic biomass. The combustion kinetics of ethyl levulinate have been investigated. Shock tube and rapid compression machine apparatuses are utilised to acquire gas phase ignition delay measurements of 0.5% ethyl levulinate/O2 mixtures at ϕ = 1.0 and ϕ = 0.5 at ∼ 10 atm over the temperature range 1000–1400 K. Ethyl levulinate is observed not to ignite at temperatures lower than ∼1040 K in the rapid compression machine. The shock tube and rapid compression machine data are closely consistent and show ethyl levulinate ignition delay to exhibit an Arrhenius dependence to temperature. These measurements are explained by the construction and analysis of a detailed chemical kinetic model. The kinetic model is completed by establishing thermochemical-kinetic analogies to 2-butanone, for the ethyl levulinate ketone functionality, and to ethyl propanoate for the ethyl ester functionality. The so constructed model is observed to describe the shock tube data very accurately, but computes the rapid compression machine data set to a lesser but still applicable fidelity. Analysis of the model suggests the autooxidation mechanism of ethyl levulinate to be entirely dominated by the propensity for the ethyl ester functionality to unimolecularly decompose to form levulinic acid and ethylene. The subsequent reaction kinetics of these species is shown to dictate the overall rate of the global combustion reaction. This model is then use to estimate the Research and Motored Octane Numbers of ethyl levulinate to be ≥97.7 and ≥ 93, respectively. With this analysis ethyl levulinate would be best suited as a gasoline fuel component, rather than as a diesel fuel as suggested in the literature. Indeed it may be considered to be useful as an

Synthesis and characterization of UV-absorbing fluorine-silicone acrylic resin polymer

Science.gov (United States)

Lei, Huibin; He, Deliang; Guo, Yanni; Tang, Yining; Huang, Houqiang

2018-06-01

A series of UV-absorbing fluorine-silicone acrylic resin polymers containing different amount of UV-absorbent were successfully prepared by solution polymerization, with 2-[3-(2H-Benzotriazol-2-yl)-4-hydroxyphenyl] ethyl methacrylate (BHEM), vinyltrimethoxysilane (VTMS) and hexafluorobutyl methacrylate (HFMA) as modifying monomers. The acrylic polymers and the coatings thereof were characterized by Fourier transform infrared spectrum (FT-IR), X-ray photoelectron spectroscopy (XPS), Ultraviolet-visible (UV-vis) absorption spectrum, thermogravimetric analysis (TGA), water contact angle (CA) and Xenon lamp artificial accelerated aging tests. Results indicated that the resin exhibited high UV absorption performance as well as good thermal stability. The hydrophobicity of the coatings was of great improvement because of the bonded fluorine and silicone. Meanwhile, the weather-resistance was promoted through preferably colligating the protective effects of BHEM, organic fluorine and silicone. Also, a fitting formula about the weatherability with the BMHE content was tentatively proposed.

Improved stability and enhanced efficiency to degrade chlorimuron-ethyl by the entrapment of esterase SulE in cross-linked poly (γ-glutamic acid)/gelatin hydrogel

Energy Technology Data Exchange (ETDEWEB)

Yang, Liqiang [State Key Laboratory of Forest and Soil Ecology, Institute of Applied Ecology, Chinese Academy of Sciences, Shenyang (China); University of Chinese Academy of Sciences, Beijing (China); Li, Xinyu; Li, Xu; Su, Zhencheng; Zhang, Chenggang; Xu, MingKai [State Key Laboratory of Forest and Soil Ecology, Institute of Applied Ecology, Chinese Academy of Sciences, Shenyang (China); Zhang, Huiwen, E-mail: hwzhang@iae.ac.cn [State Key Laboratory of Forest and Soil Ecology, Institute of Applied Ecology, Chinese Academy of Sciences, Shenyang (China)

2015-04-28

Highlights: • Esterase SulE was entrapped in a three-dimensional network of CPE. • CPE-SulE obviously improved thermostability, pH stability and reusability. • CPE-SulE displayed obviously enhanced efficiency in degrading chlorimuron-ethyl. • The three-dimensional network and kinetic parameters of CPE-SulE were analysed. • CPE-SulE possesses the great potential to remediate chlorimuron-ethyl contaminated in situ. - Abstract: Free enzymes often undergo some problems such as easy deactivation, low stability, and less recycling in biodegradation processes, especially in soil condition. A novel esterase SulE, which is responsible for primary degradation of a wide range of sulfonylurea herbicides by methyl or ethyl ester de-esterification, was expressed by strain Hansschlegelia sp. CHL1 and entrapped for the first time in an environment-friendly, biocompatible and biodegradable cross-linked poly (γ-glutamic acid)/gelatin hydrogel (CPE). The activity and stability of CPE-SulE were compared with free SulE under varying pH and temperature condition by measuring chlorimuron-ethyl residue. Meanwhile, the three-dimensional network of CPE-SulE was verified by scanning electron microscopy (SEM). The results showed that CPE-SulE obviously improved thermostability, pH stability and reusability compared with free SulE. Furthermore, CPE-SulE enhanced degrading efficiency of chlorimuron-ethyl in both soil and water system, especially in acid environment. The characteristics of CPE-SulE suggested the great potential to remediate chlorimuron-ethyl contaminated soils in situ.

Improved stability and enhanced efficiency to degrade chlorimuron-ethyl by the entrapment of esterase SulE in cross-linked poly (γ-glutamic acid)/gelatin hydrogel

International Nuclear Information System (INIS)

Yang, Liqiang; Li, Xinyu; Li, Xu; Su, Zhencheng; Zhang, Chenggang; Xu, MingKai; Zhang, Huiwen

2015-01-01

Highlights: • Esterase SulE was entrapped in a three-dimensional network of CPE. • CPE-SulE obviously improved thermostability, pH stability and reusability. • CPE-SulE displayed obviously enhanced efficiency in degrading chlorimuron-ethyl. • The three-dimensional network and kinetic parameters of CPE-SulE were analysed. • CPE-SulE possesses the great potential to remediate chlorimuron-ethyl contaminated in situ. - Abstract: Free enzymes often undergo some problems such as easy deactivation, low stability, and less recycling in biodegradation processes, especially in soil condition. A novel esterase SulE, which is responsible for primary degradation of a wide range of sulfonylurea herbicides by methyl or ethyl ester de-esterification, was expressed by strain Hansschlegelia sp. CHL1 and entrapped for the first time in an environment-friendly, biocompatible and biodegradable cross-linked poly (γ-glutamic acid)/gelatin hydrogel (CPE). The activity and stability of CPE-SulE were compared with free SulE under varying pH and temperature condition by measuring chlorimuron-ethyl residue. Meanwhile, the three-dimensional network of CPE-SulE was verified by scanning electron microscopy (SEM). The results showed that CPE-SulE obviously improved thermostability, pH stability and reusability compared with free SulE. Furthermore, CPE-SulE enhanced degrading efficiency of chlorimuron-ethyl in both soil and water system, especially in acid environment. The characteristics of CPE-SulE suggested the great potential to remediate chlorimuron-ethyl contaminated soils in situ

Constraining the Molecular Complexity in the Interstellar Medium—The Formation of Ethyl Methyl Ether (CH3OCH2CH3) in Star-forming Regions

Science.gov (United States)

Bergantini, Alexandre; Frigge, Robert; Kaiser, Ralf I.

2018-05-01

We report the first confirmed synthesis of ethyl methyl ether (EME, CH3CH2OCH3) within astrophysical model ices containing water (H2O) and methane (CH4) exposed to ionizing radiation at ultra-low temperatures of 5 K. EME (also known as methoxyethane), was recently observed toward Orion KL and currently is the largest confirmed oxygen-bearing molecule found in the interstellar medium. Exploiting isomer-selective photoionization (PI) of the subliming molecules in the temperature-programmed desorption phase at 10.49, 9.92, and 9.70 eV, coupled with reflectron time-of-flight mass spectrometry and isotopic substitution experiments (H2 18O–CH4), the detection of fragment ions of EME at m/z = 45 (C2H5O+) and m/z = 59 (C3H7O+), and probing the proton transfer in subliming ethanol–EME complexes via m/z = 61 (C3H9O+), the present study reveals that EME can be formed from suprathermal reactions initiated by cosmic rays and secondary electrons generated within astrophysical ices. The detection of EME in our experiments represents a significant advance in the understanding of formation pathways of complex organic molecules present in hot cores and helps to constrain astrochemical models on the formation of such species within molecular clouds.

40 CFR 180.470 - Acetochlor; tolerances for residues.

Science.gov (United States)

2010-07-01

...'-methyl-6-ethyl-N-ethoxymethylacetanilide, and its metabolites containing the ethyl methyl aniline (EMA) moiety and the hydroxyethyl methyl aniline (HEMA) moiety. Both parent and the named metabolites shall be determined as ethyl methyl aniline (EMA) and hydroxyethyl methyl aniline (HEMA), and calculated as the...

Solubility and solution thermodynamics of 2-methyl-6-nitroaniline in ten organic solvents at elevated temperatures

International Nuclear Information System (INIS)

Cong, Yang; Wang, Jian; Du, Cunbin; Han, Shuo; Zhao, Hongkun

2016-01-01

Highlights: • Solubility of 2-methyl-6-nitroaniline in ten solvents were determined. • The solubility were correlated with four thermodynamic models. • Standard dissolution enthalpy and excess enthalpy of the solutions were computed. - Abstract: Knowledge of solubility for 2-methyl-6-nitroaniline in different solvents is essential for its purification and further theoretical studies. In this paper, the solid-liquid equilibrium for 2-methyl-6-nitroaniline in ten pure organic solvents (methanol, ethanol, n-propanol, isopropanol, toluene, ethyl acetate, acetonitrile, acetone, cyclohexane and 1,4-dioxane) was established using the isothermal saturation method at temperatures T = (278.15–313.15) K under pressure of 101.2 kPa, and the solubility of 2-methyl-6-nitroaniline in these solvents were determined by a high-performance liquid chromatography (HPLC). In general, the mole fraction solubility followed the following order from high to low in different solvents: 1,4-dioxane (0.1799–0.3390) > acetone (0.1128–0.3010) > ethyl acetate (0.08414–0.2654) > acetonitrile (0.04179–0.2027) > toluene (0.02367–0.1104) > n-propanol (0.01080–0.04514) > ethanol (0.01020–0.04202) > isopropanol (0.008595–0.03763) > methanol (0.007391–0.03198) > cyclohexane (0.001027–0.005617). The modified Apelblat equation, λh equation, Wilson model and NRTL model were employed to correlate the measured solubility data of 2-methyl-6-nitroaniline in the selected solvents. Results indicated that the largest values of RAD and RMSD acquired by the four models were less than 0.76% and 9.13 × 10"−"4, respectively. The modified Apelblat equation provided better results than the other three models. Furthermore, the standard dissolution enthalpy and excess enthalpy of the solutions were computed from the solubility values. The standard dissolution enthalpies vary within the range from (14.88 to 45.57) kJ·mol"−"1 and are all positive, the dissolution process of 2-methyl-6

21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-ethyl acrylate copolymers. 177.1320... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1320 Ethylene-ethyl acrylate copolymers. Ethylene-ethyl acrylate copolymers may be safely used to produce packaging materials, containers...

Sequence distribution of acetaldehyde-derived N2-ethyl-dG adducts along duplex DNA.

Science.gov (United States)

Matter, Brock; Guza, Rebecca; Zhao, Jianwei; Li, Zhong-ze; Jones, Roger; Tretyakova, Natalia

2007-10-01

Acetaldehyde (AA) is the major metabolite of ethanol and may be responsible for an increased gastrointestinal cancer risk associated with alcohol beverage consumption. Furthermore, AA is one of the most abundant carcinogens in tobacco smoke and induces tumors of the respiratory tract in laboratory animals. AA binding to DNA induces Schiff base adducts at the exocyclic amino group of dG, N2-ethylidene-dG, which are reversible on the nucleoside level but can be stabilized by reduction to N2-ethyl-dG. Mutagenesis studies in the HPRT reporter gene and in the p53 tumor suppressor gene have revealed the ability of AA to induce G-->A transitions and A-->T transversions, as well as frameshift and splice mutations. AA-induced point mutations are most prominent at 5'-AGG-3' trinucleotides, possibly a result of sequence specific adduct formation, mispairing, and/or repair. However, DNA sequence preferences for the formation of acetaldehyde adducts have not been previously examined. In the present work, we employed a stable isotope labeling-HPLC-ESI+-MS/MS approach developed in our laboratory to analyze the distribution of acetaldehyde-derived N2-ethyl-dG adducts along double-stranded oligodeoxynucleotides representing two prominent lung cancer mutational "hotspots" and their surrounding DNA sequences. 1,7,NH 2-(15)N-2-(13)C-dG was placed at defined positions within DNA duplexes derived from the K-ras protooncogene and the p53 tumor suppressor gene, followed by AA treatment and NaBH 3CN reduction to convert N2-ethylidene-dG to N2-ethyl-dG. Capillary HPLC-ESI+-MS/MS was used to quantify N2-ethyl-dG adducts originating from the isotopically labeled and unlabeled guanine nucleobases and to map adduct formation along DNA duplexes. We found that the formation of N2-ethyl-dG adducts was only weakly affected by the local sequence context and was slightly increased in the presence of 5-methylcytosine within CG dinucleotides. These results are in contrast with sequence

Study of drug release and tablet characteristics of silicone adhesive matrix tablets.

Science.gov (United States)

Tolia, Gaurav; Li, S Kevin

2012-11-01

Matrix tablets of a model drug acetaminophen (APAP) were prepared using a highly compressible low glass transition temperature (T(g)) polymer silicone pressure sensitive adhesive (PSA) at various binary mixtures of silicone PSA/APAP ratios. Matrix tablets of a rigid high T(g) matrix forming polymer ethyl cellulose (EC) were the reference for comparison. Drug release study was carried out using USP Apparatus 1 (basket), and the relationship between the release kinetic parameters of APAP and polymer/APAP ratio was determined to estimate the excipient percolation threshold. The critical points attributed to both silicone PSA and EC tablet percolation thresholds were found to be between 2.5% and 5% w/w. For silicone PSA tablets, satisfactory mechanical properties were obtained above the polymer percolation threshold; no cracking or chipping of the tablet was observed above this threshold. Rigid EC APAP tablets showed low tensile strength and high friability. These results suggest that silicone PSA could eliminate issues related to drug compressibility in the formulation of directly compressed oral controlled release tablets of poorly compressible drug powder such as APAP. No routinely used excipients such as binders, granulating agents, glidants, or lubricants were required for making an acceptable tablet matrix of APAP using silicone PSA. Copyright © 2012 Elsevier B.V. All rights reserved.

Experimental (liquid + liquid) equilibrium data for ternary and quaternary mixtures of fatty acid methyl and ethyl esters (FAME/FAEE) from soybean oil

International Nuclear Information System (INIS)

Beneti, Stéphani C.; Lanza, Marcelo; Mazutti, Marcio A.; Kunita, Marcos Hiroiuqui; Cardozo-Filho, Lúcio; Vladimir Oliveira, J.

2014-01-01

Highlights: • Innovative technique for quantification of compounds involved in the biodiesel production. • Easy and quick determination from NIR combined with multivariate calibration. • Reliable LLE correlation and predictions can be attained from the technique. -- Abstract: This work is aimed at providing an easy and quick determination of the biodiesel products using near infrared spectroscopy (NIR) by combination with the multivariate calibration in the analysis of (liquid + liquid) equilibrium (LLE) data for ternary and quaternary mixtures containing soybean fatty acid methyl (FAME) and ethyl (FAEE) esters, glycerol, ethanol, methanol and water, at various temperatures. The mass balance for the compositions obtained for each phase was carried out so as to demonstrate the reliability of the models generated by the multivariate calibration. Two distinct phases are observed, a glycerol-rich and the other ester-rich, while ethanol is dissolved among the phases hence reducing the partial mutual miscibility between glycerol and ester. Through (liquid + liquid) equilibrium (LLE) results, systems containing FAEE at T = 318.15 K and 303.15 K (calibration using data obtained at temperature of 318.15 K), a good agreement is verified among the values determined using conventional and NIR technique for alcoholic phase (AP) or aqueous phase (WP) and biodiesel phase (BP). Likewise in the systems containing FAME at 318.15 K, 303.15 K and 333.15 K (calibration using data obtained at temperature of 318.15 K), the LLE results were reproduced at the upper and lower temperature to the tests of the reproducibility of the models generated by the multivariate calibration

Glycerol transesterification with ethyl acetate to synthesize acetins using ethyl acetate as reactant and entrainer

Directory of Open Access Journals (Sweden)

Amin Shafiei

2017-03-01

Full Text Available Transesterification of glycerol with ethyl acetate was performed over acidic catalysts in the batch and semi-batch systems. Ethyl acetate was used as reactant and entrainer to remove the produced ethanol during the reaction, through azeotrope formation. Since the azeotrope of ethyl acetate and ethanol forms at 70 oC, all the experiments were performed at this temperature. Para-toluene sulfonic acid, sulfuric acid, and Amberlyst 36 were used as catalyst. The effect of process parameters including ethyl acetate to glycerol molar ratio (6-12, reaction time (3-9 h, and the catalyst to glycerol weight (2.5-9.0%, on the conversion and products selectivities were investigated. Under reflux conditions, 100% glycerol conversion was obtained with 45%, 44%, and 11% selectivity to monoacetin, diacetin, and triacetin, respectively. Azeotropic reactive distillation led to 100% conversion of glycerol with selectivities of 3%, 48% and 49% for monoacetin, diacetin, and triacetin. During the azeotropic reactive distillation, it was possible to remove ethanol to shift the equilibrium towards diacetin and triacetin. Therefore, the total selectivity to diacetin and triacetin was increased from 55% to 97% through azeotropic distillation.

Nuclear reactor fuel element

International Nuclear Information System (INIS)

D'Eye, R.W.M.; Shennan, J.V.; Ford, L.H.

1977-01-01

Fuel element with particles from ceramic fissionable material (e.g. uranium carbide), each one being coated with pyrolitically deposited carbon and all of them being connected at their points of contact by means of an individual crossbar. The crossbar consists of silicon carbide produced by reaction of silicon metal powder with the carbon under the influence of heat. Previously the silicon metal powder together with the particles was kneaded in a solvent and a binder (e.g. epoxy resin in methyl ethyl ketone plus setting agent) to from a pulp. The reaction temperature lies at 1750 0 C. The reaction itself may take place in a nitrogen atmosphere. There will be produced a fuel element with a high overall thermal conductivity. (DG) [de

Solubility comparison and partial molar volumes of 1,2-hexanediol before and after end-group modification by methyl oxalyl chloride and ethyl oxalyl monochloride in supercritical CO2

International Nuclear Information System (INIS)

Zhao, Lu; Yang, Hai-Jian; Cai, Zhuofu

2013-01-01

Highlights: ► Two new “CO 2 -philic” compounds were designed and synthesized. ► The tested solubility data were calculated and correlated with two models. ► Satisfactory agreements were obtained between the tested and calculated data. ► The partial molar volumes V ¯ 2 for three compounds were estimated. - Abstract: Bis(methoxy oxalic)-1,2-haxenediester and bis(ethoxy oxalic)-1,2-haxenediester were synthesized by modifying the end groups of 1,2-hexanediol with methyl oxalyl chloride and ethyl oxalyl monochloride. The solubilities of all three compounds in supercritical carbon dioxide were determined at different conditions of pressures (8.8 to 18.8) MPa and temperatures (313, 333, and 353) K. Then, the solubility data were correlated with the Bartle model and the Chrastil model. The average absolute relative deviation (AARD) for the Bartle model was in the range of (3.89 to 25.46)% which is within a good approximation. The Chrastil model also showed satisfactory agreement and the AARD was in the range of (3.70 to 16.92)%. Furthermore, the partial molar volumes of those compounds were estimated following the theory developed by Kumar and Johnston.

Study of radiation formation of methyl-iodide Part 2

International Nuclear Information System (INIS)

Bartonicek, B.; Schweiner, Z.; Bednar, J.; Hladky, E.

1975-01-01

Purified methane, ethylene, iodine, methyl iodide, ethyl iodide and hydrogen iodide were irradiated and/or pyrolyzed in Pyrex ampoules by 60 Co-γ-radiation at temperatures between 150 and 450 deg C. The results on radiolysis and pyrolysis were as follows: 1., The most thermally stable product is hydrogen iodide in which already at 450 deg C essen-tially all originally present iodine appears. 2., The radiolytic formation of methyl iodide and hydrogen iodide is positively influenced by the rise in temperature, This and the absolute values of yields indicate a chain mechanism of radiolytic (and pyrolytic) decomposition of the mixture. 3., The ratio of equilibrium concentrations [HI]/[CH 3 I] increases with increasing temperature of pyrolysis showing that HI is the end product of the thermal chain reaction. Methyl iodide is likely to contribute (by its thermal decomposition) to the initiation and propagation of this chain reaction. 4., The negligible temperature dependence of G(H 2 ) and the absence of molecular hydrogen among the products of pyrolytic decomposition of methane-iodine mixtures shows, that (up to 450 deg C) H atoms do not play any role in the thermal chain decomposition of these mixtures. (K.A.)

Durable antimicrobial finishing of cellulose with QSA silicone by supercritical adsorption

International Nuclear Information System (INIS)

Chen Yong; Niu Mengqi; Yuan Shu; Teng Hongni

2013-01-01

Highlights: ► CO 2 -philic QAS silicone was synthesized through hydrosilylation and quaternization. ► QAS silicone was coated on cotton by adsorption from scCO 2 . ► The coating procedure did not need covalently bonding tethering groups. ► The coating provided potent biocidal activities against Staphylococcus aureus and Escherichia coli. ► Antibacterial coating was very stable toward washing and UV irradiation. - Abstract: This study demonstrated a generic and simple approach to generate durable antibacterial ability on cellulose without using covalently bonding tethering groups that limit the structure design. CO 2 -philic silicone with quaternary ammonium salt (QAS) pendants was synthesized through hydrosilylation reaction of poly(methylhydrosiloxane) (PMHS) and 2-(dimethylamino)ethyl acrylate in the presence of platinum-based catalyst and subsequent quaternization with 1-bromohexane. The resultant QAS silicone was deposited onto cellulose by adsorption from supercritical CO 2 (scCO 2 ) to provide potent biocidal activities against Staphylococcus aureus and Escherichia coli. Presented data also showed that the antibacterial layer was very stable toward washing and UV irradiation owning to the low surface tension and relatively high bond energy of the backbone of silicone. This procedure is applicable to substrates of other shape and chemistry.

Analysis and interpretation of specific ethanol metabolites, ethyl sulfate, and ethyl glucuronide in sewage effluent for the quantitative measurement of regional alcohol consumption.

Science.gov (United States)

Reid, Malcolm J; Langford, Katherine H; Mørland, Jørg; Thomas, Kevin V

2011-09-01

The quantitative measurement of urinary metabolites in sewage streams and the subsequent estimation of consumption rates of the parent compounds have previously been demonstrated for pharmaceuticals and narcotics. Ethyl sulfate and ethyl glucuronide are excreted in urine following the ingestion of alcohol, and are useful biomarkers for the identification of acute alcohol consumption. This study reports a novel ion-exchange-mediated chromatographic method for the quantitative measurement of ethyl sulfate and ethyl glucuronide in sewage effluent, and presents a novel calculation method for the purposes of relating the resulting sewage concentrations with rates of alcohol consumption in the region. A total of 100 sewage samples covering a 25-day period were collected from a treatment plant servicing approximately 500,000 people, and analyzed for levels of ethyl sulfate and ethyl glucuronide. The resulting data were then used to estimate combined alcohol consumption rates for the region, and the results were compared with alcohol related sales statistics for the same region. Ethyl glucuronide was found to be unstable in sewage effluent. Ethyl sulfate was stable and measurable in all samples at concentrations ranging from 16 to 246 nM. The highest concentrations of the alcohol biomarker were observed during weekend periods. Sixty one percent of the total mass of ethyl sulfate in sewage effluent corresponds to alcohol consumption on Friday and Saturday. Sales statistics for alcohol show that consumption in the region is approximately 6,750 kg/d. The quantity of ethyl sulfate passing through the sewage system is consistent with consumption of 4,900 to 7,800 kg/d.   Sewage epidemiology assessments of ethyl sulfate can provide accurate estimates of community alcohol consumption, and detailed examination of the kinetics of this biomarker in sewage streams can also identify time-dependent trends in alcohol consumption patterns. 2011 by the Research Society on Alcoholism.

Ethyl diazoacetate synthesis in flow

Directory of Open Access Journals (Sweden)

Mariëlle M. E. Delville

2013-09-01

Full Text Available Ethyl diazoacetate is a versatile compound in organic chemistry and frequently used on lab scale. Its highly explosive nature, however, severely limits its use in industrial processes. The in-line coupling of microreactor synthesis and separation technology enables the synthesis of this compound in an inherently safe manner, thereby making it available on demand in sufficient quantities. Ethyl diazoacetate was prepared in a biphasic mixture comprising an aqueous solution of glycine ethyl ester, sodium nitrite and dichloromethane. Optimization of the reaction was focused on decreasing the residence time with the smallest amount of sodium nitrite possible. With these boundary conditions, a production yield of 20 g EDA day−1 was achieved using a microreactor with an internal volume of 100 μL. Straightforward scale-up or scale-out of microreactor technology renders this method viable for industrial application.

Electron stimulated reactions of methyl iodide coadsorbed with amorphous solid water

International Nuclear Information System (INIS)

Perry, C. C.; Faradzhev, N. S.; Madey, T. E.; Fairbrother, D. H.

2007-01-01

The electron stimulated reactions of methyl iodide (MeI) adsorbed on and suspended within amorphous solid water (ice) were studied using a combination of postirradiation temperature programmed desorption and reflection absorption infrared spectroscopy. For MeI adsorbed on top of amorphous solid water (ice), electron beam irradiation is responsible for both structural and chemical transformations within the overlayer. Electron stimulated reactions of MeI result principally in the formation of methyl radicals and solvated iodide anions. The cross section for electron stimulated decomposition of MeI is comparable to the gas phase value and is only weakly dependent upon the local environment. For both adsorbed MeI and suspended MeI, reactions of methyl radicals within MeI clusters lead to the formation of ethane, ethyl iodide, and diiodomethane. In contrast, reactions between the products of methyl iodide and water dissociation are responsible for the formation of methanol and carbon dioxide. Methane, formed as a result of reactions between methyl radicals and either parent MeI molecules or hydrogen atoms, is also observed. The product distribution is found to depend on the film's initial chemical composition as well as the electron fluence. Results from this study highlight the similarities in the carbon-containing products formed when monohalomethanes coadsorbed with amorphous solid water are irradiated by either electrons or photons

Behaviour of Some Activated Nitriles Toward Barbituric Acid, Thiobarbituric Acid and 3-Methyl-1-Phenylpyrazol-5-one

Directory of Open Access Journals (Sweden)

M. M. Habashy

2000-05-01

Full Text Available The effect of some active methylene containing heterocyclic compounds, namely barbituric acid, thiobarbituric acid and 3-methyl-1-phenylpyrazol-5-one on a-cyano-3,4,5-trimethoxycinnamonitrile and ethyl a-cyano-3,4,5-trimethoxycinnamate (1a,b was investigated. The structure of the new products was substantiated by their IR,1H-NMR and mass spectra.

Studies onthe behaviour of the insecticide 14C-Pirimiphos-Methyl in aquatic species: tilapia nilotica and potamogeton crispus plant

International Nuclear Information System (INIS)

Afifi, L.M.; Kamel, H.A.; Aly, M.A.S.

2003-01-01

The bioaccumulation and depletion of 1 4C-labelled pirimiphos-methyl (O-2- diethyl amino-6-methyl pyrimidine-4-gamma l O,O-dimethyl phosphorothioa) were monitored for 6 days following a single application at 7.5 ppm to 2 aquatic species: Bolti fish (Tilapia nilotica) and a rapid growing plant (Potamogeton crispus). The bioconcentration factor (BCF) for fish was relatively low with a maximum reached at 24 hours 122 and 55 in the absence and presence of the weed respectively. Depuration of the insecticide and/or its metabolites in clear water was readily fast. Feeding the treated dried fish to rat, the substance residues were found to be bioavailable where, 75.7% of the given amount was excreted in the urine and 15.3% in the feces. TLC analysis of the urine revealed the presence of 4 metabolites: Desethyl pirimiphos-methyl, 2-diethyl amino-4-hydroxy-6-methylpyrimidine, 2-ethyl amino-4-hydroxy-6-methyl-pyrimidine and 2-amino -4-hydroxy-6- methyl- pyrimidine

Why are ionic liquid ions mainly associated in water? A Car-Parrinello study of 1-ethyl-3-methyl-imidazolium chloride water mixture

Science.gov (United States)

Spickermann, C.; Thar, J.; Lehmann, S. B. C.; Zahn, S.; Hunger, J.; Buchner, R.; Hunt, P. A.; Welton, T.; Kirchner, B.

2008-09-01

In this study we present the results of a first principles molecular dynamics simulation of a single 1-ethyl-3-methyl-imidazolium chloride [C2C1im][Cl] ion pair dissolved in 60 water molecules. We observe a preference of the in plane chloride coordination with respect to the cation ring plane as compared to the energetic slightly more demanding on top coordination. Evaluation of the different radial distribution functions demonstrates that the structure of the hydration shell around the ion pair differs significantly from bulk water and that no true ion pair dissociation in terms of completely autonomous solvation shells takes place on the timescale of the simulation. In addition, dipole moment distributions of the solvent in distinct solvation shells around different functional parts of the [C2C1im][Cl] ion pair are calculated from maximally localized Wannier functions. The analysis of these distributions gives evidence for a depolarization of water molecules close to the hydrophobic parts of the cation as well as close to the anion. Examination of the angular distribution of different OH(H2O )-X angles in turn shows a linear coordination of chloride accompanied by a tangential orientation of water molecules around the hydrophobic groups, being a typical feature of hydrophobic hydration. Based on these orientational aspects, a structural model for the obvious preference of ion pair association is developed, which justifies the associating behavior of solvated [C2C1im][Cl] ions in terms of an energetically favorable interface between the solvation shells of the anion and the hydrophobic parts of the cation.

Synthesis of methyl (13(2)R/S)-alkyl-pyropheophorbide a and a non-epimerized chlorophyll a mimic.

Science.gov (United States)

Ogasawara, Shin; Tamiaki, Hitoshi

2015-10-15

The (13(2)R/S)-methoxycarbonyl group of methyl pheophorbides a/a' (chlorophyll a/a' derivatives) was converted to methyl, ethyl, propyl, and isopropyl groups through the C13(2)-alkylation under basic conditions followed by pyrolysis in 2,4,6-collidine with lithium iodide. All the resulting products, methyl 13(2)-alkyl-pyropheophorbides a, predominantly gave the (13(2)R)-stereoisomers with about one tenth of the (13(2)S)-epimers. Their stereochemistry was determined by 1D/2D NMR and their optical properties were characterized by visible absorption and circular dichroism spectroscopy. Methyl (13(2)R)-propyl-pyropheophorbide a was converted to (13(2)R)-propyl-pyrochlorophyll a by ester exchanging and magnesium chelating reactions. The synthetic chlorophyll a analogue showed non-epimerization at the 13(2)-position in pyridine-d5 at 40°C, while naturally occurring chlorophyll a was easily epimerized under the same conditions to give its epimeric mixture. Copyright © 2015 Elsevier Ltd. All rights reserved.

Gas chromatography-mass spectrometry of ethyl palmitate calibration and resolution with ethyl oleate as biomarker ethanol sub acute in urine application study

Science.gov (United States)

Suaniti, Ni Made; Manurung, Manuntun

2016-03-01

Gas Chromatography-Mass Spectrometry is used to separate two and more compounds and identify fragment ion specific of biomarker ethanol such as palmitic acid ethyl ester (PAEE), as one of the fatty acid ethyl esters as early detection through conyugated reaction. This study aims to calibrate ethyl palmitate and develop analysis with oleate acid. This methode can be used analysis ethanol and its chemistry biomarker in ethanol sub-acute consumption as analytical forensic toxicology. The result show that ethanol level in urine rats Wistar were 9.21 and decreased 6.59 ppm after 48 hours consumption. Calibration curve of ethyl palmitate was y = 0.2035 x + 1.0465 and R2 = 0.9886. Resolution between ethyl palmitate and oleate were >1.5 as good separation with fragment ion specific was 88 and the retention time was 18 minutes.

Bioconjugate functionalization of thermally carbonized porous silicon using a radical coupling reaction†

Science.gov (United States)

Sciacca, Beniamino; Alvarez, Sara D.; Geobaldo, Francesco; Sailor, Michael J.

2011-01-01

The high stability of Salonen’s thermally carbonized porous silicon (TCPSi) has attracted attention for environmental and biochemical sensing applications, where corrosion-induced zero point drift of porous silicon-based sensor elements has historically been a significant problem. Prepared by the high temperature reaction of porous silicon with acetylene gas, the stability of this silicon carbide-like material also poses a challenge—many sensor applications require a functionalized surface, and the low reactivity of TCPSi has limited the ability to chemically modify its surface. This work presents a simple reaction to modify the surface of TCPSi with an alkyl carboxylate. The method involves radical coupling of a dicarboxylic acid (sebacic acid) to the TCPSi surface using a benzoyl peroxide initiator. The grafted carboxylic acid species provides a route for bioconjugate chemical modification, demonstrated in this work by coupling propylamine to the surface carboxylic acid group through the intermediacy of pentafluorophenol and 1-ethyl-3-[3-dimethylaminopropyl]carbodiimide hydrochloride (EDC). The stability of the carbonized porous Si surface, both before and after chemical modification, is tested in phosphate buffered saline solution and found to be superior to either hydrosilylated (with undecylenic acid) or thermally oxidized porous Si surfaces. PMID:20967329

Biotransformation and Production from Hansenula Anomala to Natural Ethyl Phenylacetate

Directory of Open Access Journals (Sweden)

Tian Xun

2015-01-01

Full Text Available Ethyl phenylacetate can be widely applied in many industries, such as food, medicines, cosmetics and medicinal herbs. At the moment, the production of natural ethyl phenylacetate is very limited. However, the biotransformation production of natural ethyl phenylacetate has an very extensive application prospect. This paper is written by taking the phenylacetic acid tolerance and the esterifying enzyme activity as the two indexes for screening the HA14 strain of hansenula anomala mutagenic which is regarded as the microorganism of ethyl phenylacetate production through biotransformation. By optimizing the production condition of phenylacetic acid and the esterification condition of ethyl phenylacetate, the production of ethyl phenylacetate accomplished through biotransformation within 72 hours can reach 864mg/L which is 171% of that of the initial bacterial strain.

Purification and properties of a novel quizalofop-p-ethyl-hydrolyzing esterase involved in quizalofop-p-ethyl degradation by Pseudomonas sp. J-2.

Science.gov (United States)

Zhang, Hui; Li, Mengya; Li, Jie; Wang, Guangli; Liu, Yuan

2017-05-10

Quizalofop-p-ethyl (QPE) is a post-emergence herbicide that effectively controls grass weeds and is often detected in the environment. However, the biochemical and molecular mechanisms of QPE degradation in the environment remains unclear. In this study, a highly effective QPE-degrading bacterial strain J-2 was isolated from acclimated activated sludge and identified as a Pseudomonas sp., containing the QPE breakdown metabolite quizalofop acid (QA) identified by Liquid Chromatography-Ion Trap-Mass Spectrometry (LC-IT-MS n ) analysis. A novel QPE hydrolase esterase-encoding gene qpeH was cloned from strain J-2 and functionally expressed in Escherichia coli BL21 (DE3). The specific activity of recombinant QpeH was 198.9 ± 2.7 U mg -1 for QPE with K m and K cat values of 41.3 ± 3.6 μM and 127.3 ± 4.5 s -1 . The optimal pH and temperature for the recombinant QpeH were 8.0 and 30 °C, respectively and the enzyme was activated by Ca 2+ , Cd 2+ , Li + , Fe 3+ and Co 2+ and inhibited by Ni 2+ , Fe 2+ , Ag + , DEPC, SDS, Tween 80, Triton X, β-mercaptoethanol, PMSF, and pCMB. In addition, the catalytic efficiency of QpeH toward different AOPP herbicides in descending order was as follows: fenoxaprop-P-ethyl > quizalofop-P-tefuryl > QPE > haloxyfop-P-methyl > cyhalofopbutyl > clodinafop-propargyl. On the basis of the phylogenetic analysis and multiple sequence alignment, the identified enzyme QpeH, was clustered with esterase family V, suggesting a new member of this family because of its low similarity of amino acid sequence with esterases reported previously.

Solvation effect on decomposition rate of 10-methyl-10-phenylphenoxarsonium iodide in some alcohols and ketones

International Nuclear Information System (INIS)

Gavrilov, V.I.; Gumerov, N.S.; Rakhmatullin, R.R.

1989-01-01

By the method of conductometry decomposition kinetics of 10-methyl-10phenylphenoxarsonium iodide in methanol, ethanol, 2-propanol, 1-butanol, 1-pentanol and methyl ethyl ketone at initial concentration of the salt 0.00024-0.003 mol/l, is studied. It is shown that at the temperatures up to 80-95 deg C practically no decomposition of arsonium salt in methanol and ethanol is observed. With an increase in the length of alcohol alkyl radical the decomposition rate increases. The values of activation enrgy both for alcohols and ketone are approximately the same. At the same time, decomposition rate in alcohol proved much slower than in ketone, which is related to iodide-ion solvation in protic solvents

Solvation effect on decomposition rate of 10-methyl-10-phenylphenoxarsonium iodide in some alcohols and ketones

Energy Technology Data Exchange (ETDEWEB)

Gavrilov, V I; Gumerov, N S; Rakhmatullin, R R [Kazanskij Khimiko-Tekhnologicheskij Inst., Kazan (USSR)

1989-03-01

By the method of conductometry decomposition kinetics of 10-methyl-10phenylphenoxarsonium iodide in methanol, ethanol, 2-propanol, 1-butanol, 1-pentanol and methyl ethyl ketone at initial concentration of the salt 0.00024-0.003 mol/l, is studied. It is shown that at the temperatures up to 80-95 deg C practically no decomposition of arsonium salt in methanol and ethanol is observed. With an increase in the length of alcohol alkyl radical the decomposition rate increases. The values of activation enrgy both for alcohols and ketone are approximately the same. At the same time, decomposition rate in alcohol proved much slower than in ketone, which is related to iodide-ion solvation in protic solvents.

Experimental vapor pressures (from 1 Pa to 100 kPa) of six saturated Fatty Acid Methyl Esters (FAMEs): Methyl hexanoate, methyl octanoate, methyl decanoate, methyl dodecanoate, methyl tetradecanoate and methyl hexadecanoate

International Nuclear Information System (INIS)

Sahraoui, Lakhdar; Khimeche, Kamel; Dahmani, Abdallah; Mokbel, Ilham; Jose, Jacques

2016-01-01

Highlight: • Vapor-liquid equilibria, Enthalpy of Vaporization, saturated Fatty Acid Methyl Ester. - Abstract: Vapor pressures of six saturated Fatty Acid Methyl Esters (FAMEs), methyl hexanoate (or methyl caproate), methyl octanoate (or methyl caprylate), Methyl decanoate (or methyl caprate), methyl dodecanoate (or methyl laurate), methyl tetradecanoate (or methyl myristate), and methyl hexadecanoate (or methyl palmitate) were measured from 1 Pa to 100 kPa and at temperature range between 262 and 453 K using a static apparatus. The experimental data (P-T) were compared with the available literature data.

Method of preparing 17β-hydroxy-4-androstene-3-one, 17α-methyl-17β-hydroxy-4-androstene-3-one and 17β-hydroxy-4-estrene-3-one labelled with iodine radioisotopes

International Nuclear Information System (INIS)

Kozak, I.; Dvorak, P.; Hampl, R.

1983-01-01

The patent claims the preparation of radioactive iodine derivatives of testosterone, methyl testosterone, and nortestosterone with the iodine atom bound directly to the steroid skeleton. An aqueous solution of carrier-free radioactive sodium iodide is evaporated until dry. The evaporation residue is extracted with a polar organic solvent and the resulting extract is added to the steroid designed for labelling. The solution is evaporated until dry and the evaporation residue is heated at a temperature within the range of the melting temperature of the respective steroid to 190 degC. To separate the immunoreactive radioactive product from admixtures, repeated thin-layer (silica gel) chromatography is used in cyclohexane-ethyl acetate (ratio 1:1) and benzene-methanol (ratio 9:1) systems. Methyl ethyl ketone, methanol, acetone and diethyl ether are used as polar solvents. (J.P.)

Synthesis and characterization of a thermo-sensitive poly( N-methyl acryloylglycine methyl ester) used as a drug release carrier

Science.gov (United States)

Deng, Kui-Lin; Zhong, Hai-Bin; Jiao, Yi-Suo; Fan, Ting; Qiao, Xiao; Zhang, Peng-Fei; Ren, Xiao-Bo

2010-06-01

In this article, poly( N-methyl acryloylglycine methyl ester) (PNMAME) was prepared as a novel thermosensitive material with a lower critical solution temperature (LCST) at around 49.5°C. The chemical structures of the monomer NMAME and PNMAME were characterized by 1H NMR and IR measurements. The LCST was investigated systematically as a function of PNMAME concentration, inorganic salt solution and pH value. The results indicated that LCST of PNMAME was obviously dependent on PNMAME concentration and pH. The LCST was increased with a decrease in pH value and PNMAME concentration. To obtain a thermo-sensitive hydrogel with the phase transition temperature close to human body temperature, the copolymerization was conducted between NMAME and N-acryloylglycine ethyl ester (NAGEE). The release behavior of caffeine was evaluated at different temperatures and contents of cross-linkers ( N, N-methylenebis(acrylamide) (NMBA)). The increase of cross-linker content led to a decrease in the release rate of caffeine due to higher crossing density in the hydrogel network. In addition, a faster release of caffeine from the hydrogel with 3% NMBA at 37°C was found in contrast to that at 18°C.

Methyl-coenzyme M reductase from methanogenic archaea: isotope effects on label exchange and ethane formation with the homologous substrate ethyl-coenzyme M.

Science.gov (United States)

Scheller, Silvan; Goenrich, Meike; Thauer, Rudolf K; Jaun, Bernhard

2013-10-09

Ethyl-coenzyme M (CH3CH2-S-CH2CH2-SO3(-), Et-S-CoM) serves as a homologous substrate for the enzyme methyl-coenzyme M reductase (MCR) resulting in the product ethane instead of methane. The catalytic reaction proceeds via an intermediate that already contains all six C-H bonds of the product. Because product release occurs after a second, rate-limiting step, many cycles of intermediate formation and reconversion to substrate occur before a substantial amount of ethane is released. In deuterated buffer, the intermediate becomes labeled, and C-H activation in the back reaction rapidly leads to labeled Et-S-CoM, which enables intermediate formation to be detected. Here, we present a comprehensive analysis of this pre-equilibrium. (2)H- and (13)C-labeled isotopologues of Et-S-CoM were used as the substrates, and the time course of each isotopologue was followed by NMR spectroscopy. A kinetic simulation including kinetic isotope effects allowed determination of the primary and α- and β-secondary isotope effects for intermediate formation and for the C-H/C-D bond activation in the ethane-containing intermediate. The values obtained are in accordance with those found for the native substrate Me-S-CoM (see preceding publication, Scheller, S.; Goenrich, M.; Thauer, R. K.; Jaun, B. J. Am. Chem. Soc. 2013, 135, DOI: 10.1021/ja406485z) and thus imply the same catalytic mechanism for both substrates. The experiment by Floss and co-workers, demonstrating a net inversion of configuration to chiral ethane with CH3CDT-S-CoM as the substrate, is compatible with the observed rapid isotope exchange if the isotope effects measured here are taken into account.

Supercritical antisolvent co-precipitation of rifampicin and ethyl cellulose.

Science.gov (United States)

Djerafi, Rania; Swanepoel, Andri; Crampon, Christelle; Kalombo, Lonji; Labuschagne, Philip; Badens, Elisabeth; Masmoudi, Yasmine

2017-05-01

Rifampicin-loaded submicron-sized particles were prepared through supercritical anti-solvent process using ethyl cellulose as polymeric encapsulating excipient. Ethyl acetate and a mixture of ethyl acetate/dimethyl sulfoxide (70/30 and 85/15) were used as solvents for both drug and polymeric excipient. When ethyl acetate was used, rifampicin was crystallized separately without being embedded within the ethyl cellulose matrix while by using the ethyl acetate/dimethyl sulfoxide mixture, reduced crystallinity of the active ingredient was observed and a simultaneous precipitation of ethyl cellulose and drug was achieved. The effect of solvent/CO 2 molar ratio and polymer/drug mass ratio on the co-precipitates morphology and drug loading was investigated. Using the solvent mixture, co-precipitates with particle sizes ranging between 190 and 230nm were obtained with drug loading and drug precipitation yield from respectively 8.5 to 38.5 and 42.4 to 77.2% when decreasing the ethyl cellulose/rifampicin ratio. Results show that the solvent nature and the initial drug concentrations affect morphology and drug precipitation yield of the formulations. In vitro dissolution studies revealed that the release profile of rifampicin was sustained when co-precipitation was carried out with the solvent mixture. It was demonstrated that the drug to polymer ratio influenced amorphous content of the SAS co-precipitates. Differential scanning calorimetry thermograms and infrared spectra revealed that there is neither interaction between rifampicin and the polymer nor degradation of rifampicin during co-precipitation. In addition, stability stress tests on SAS co-precipitates were carried out at 75% relative humidity and room temperature in order to evaluate their physical stability. SAS co-precipitates were X-ray amorphous and remained stable after 6months of storage. The SAS co-precipitation process using a mixture of ethyl acetate/dimethyl sulfoxide demonstrates that this strategy can

Ethyl pyruvate protects colonic anastomosis from ischemia-reperfusion injury.

Science.gov (United States)

Unal, B; Karabeyoglu, M; Huner, T; Canbay, E; Eroglu, A; Yildirim, O; Dolapci, M; Bilgihan, A; Cengiz, O

2009-03-01

Ethyl pyruvate is a simple derivative in Ca(+2)- and K(+)-containing balanced salt solution of pyruvate to avoid the problems associated with the instability of pyruvate in solution. It has been shown to ameliorate the effects of ischemia-reperfusion (I/R) injury in many organs. It has also been shown that I/R injury delays the healing of colonic anastomosis. In this study, the effect of ethyl pyruvate on the healing of colon anastomosis and anastomotic strength after I/R injury was investigated. Anastomosis of the colon was performed in 32 adult male Wistar albino rats divided into 4 groups of 8 individuals: (1) sham-operated control group (group 1); (2) 30 minutes of intestinal I/R by superior mesenteric artery occlusion (group 2); (3) I/R+ ethyl pyruvate (group 3), ethyl pyruvate was administered as a 50-mg/kg/d single dose; and (4) I/R+ ethyl pyruvate (group 4), ethyl pyruvate administration was repeatedly (every 6 hours) at the same dose (50 mg/kg). On the fifth postoperative day, animals were killed. Perianastomotic tissue hydroxyproline contents and anastomotic bursting pressures were measured in all groups. When the anastomotic bursting pressures and tissue hydroxyproline contents were compared, it was found that they were decreased in group 2 when compared with groups 1, 3, and 4 (P .05). Ethyl pyruvate significantly prevents the delaying effect of I/R injury on anastomotic strength and healing independent from doses of administration.

Synthesis and evaluation of 6-[11C]Methoxy-3-[2- [1-(phenylmethyl)-4-piperidinyl]ethyl]-1,2-benzisoxazole as an in vivo radioligand for acetylcholinesterase

International Nuclear Information System (INIS)

Brown-Proctor, Clive; Snyder, Scott E.; Sherman, Phillip S.; Kilbourn, Michael R.

1999-01-01

6-Methoxy-3-[2-[1-(phenylmethyl)-4-piperidinyl]ethyl]-1,2-benzisoxazole is a high affinity (K i =8.2 nM) reversible inhibitor of acetylcholinesterase (AChE). The carbon-11 labeled form was prepared in high (>97%) radiochemical purity and with specific activities of 37 ± 20 GBq/μmol at end of synthesis, by the alkylation of the desmethyl precursor with [ 11 C]methyl trifluoromethanesulfonate in N,N-dimethylformamide at room temperature. In vivo studies in mice demonstrated good blood brain permeability but essentially uniform regional brain distribution. Thus, despite in vitro and in vivo activity as an AChE inhibitor, 6-[ 11 C]methoxy-3-[2-[1-(phenylmethyl)-4-piperidinyl]ethyl]-1, 2-benzisoxazole does not appear to be a good candidate for in vivo imaging studies of AChE in the mammalian brain

Synthesis of 7-[α-(2-amino-[2-14C]thiazol-4-yl)-α-(Z)-methoxyimin oacetamido]-3-(1-methylpyrrolidinio)methyl-3-cephem-4-carboxylate hydrochloride ([14C]cefepime hydrochloride)

International Nuclear Information System (INIS)

Standridge, R.T.; Swigor, J.E.

1993-01-01

The title compound ([ 14 C]cefepime hydrochloride) was prepared as follows:- [ 14 C]Thiourea was condensed with ethyl 4-bromo-3-oxo-2-methoxyimino-acetate providing ethyl 2-(2-amino-4-[2- 14 C] thiazolyl)-2-methoxyi-minoacetate as the pure Z-isomer. Saponification gave the amino acid this was reacted with 1-hydroxybenzotriazole to give the activated ester. Condensation in situ with 7-amino-3-(1-methylpyrrolidinio) methyl-3-cephem-4-carboxylate yielded the product as the pure sulfate salt. Treatment of the sulfate salt with base provided the zwitterion isolated as the stable N-methyl-2-pyrrolidinone adduct. An aqueous solution of the adduct was converted to the crystalline title compound, [ 14 C]Cefepime hydrochloride hydrate, with hydrochloric acid/acetone. Radiochemical purity was 99.0% and specific activity, 34.2 μCi/mg. Overall yield from [ 14 C]thiourea was 18%. (Author)

Icosapent ethyl: a review of its use in severe hypertriglyceridemia.

Science.gov (United States)

Kim, Esther S; McCormack, Paul L

2014-12-01

Icosapent ethyl (Vascepa®) is a high-purity ethyl ester of eicosapentaenoic acid (EPA) that is de-esterified to EPA following oral administration. Both EPA and docosahexaenoic acid (DHA) are long-chain omega-3 fatty acids that have been associated with triglyceride (TG)-lowering. However, DHA has been associated with increased low-density lipoprotein cholesterol (LDL-C) levels. Icosapent ethyl contains ≥96 % of the EPA ethyl ester, does not contain DHA, and is approved in the USA for use as an adjunct to diet to lower TG levels in adult patients with severe (≥500 mg/dL [≥5.65 mmol/L]) hypertriglyceridemia. In a pivotal phase III trial, oral icosapent ethyl 4 g/day significantly decreased the placebo-corrected median TG levels by 33.1 %. It did not increase LDL-C, had favorable effects on other lipid parameters, and had a tolerability profile similar to that of placebo. Therefore, icosapent ethyl is an effective and well-tolerated agent for the treatment of severe hypertriglyceridemia in adults.

Ethyl group as matrix modifier and inducer of ordered domains in hybrid xerogels synthesised in acidic media using ethyltriethoxysilane (ETEOS) and tetraethoxysilane (TEOS) as precursors

International Nuclear Information System (INIS)

Rios, Xabier; Moriones, Paula; Echeverría, Jesús C.; Luquin, Asunción; Laguna, Mariano; Garrido, Julián J.

2013-01-01

Hybrid silica xerogels favourably combine the properties of organic and inorganic components in one material; consequently these materials are useful for multiple applications. The versatility and mild synthetic conditions provided by the sol-gel process are ideal for the synthesis of hybrid materials. The specific aims of this study were to synthesise hybrid xerogels in acidic media using tetraethoxysilane (TEOS) and ethyltriethoxysilane (ETEOS) as silica precursors, and to assess the role of the ethyl group as a matrix modifier and inducer of ordered domains in xerogels. All xerogels were synthesised at pH 4.5, at 60 °C, with 1:4.75:5.5 TEOS:EtOH:H 2 O molar ratio. Gelation time exponentially increased with the ETEOS molar ratio. Incorporation of the ethyl groups into the structure of xerogels reduced cross-linking, increased the average siloxane bond length, and promoted the formation of ordered domains. As a result, a transition from Q n to T n signals detected in the 29 Si NMR spectra, the Si–O structural band in the FTIR spectra shifted to lower wavelength, and a new peak in the XRD pattern at 2θ < 10° appeared in the XRD patterns. Mass spectroscopy detected fragments with high numbers of silicon atoms and a polymeric distribution. - Graphical abstract: Display Omitted - Highlights: • Hybrid xerogels were synthesised for ETEOS/TEOS mixtures up to 80% ETEOS. • The gelification time exponentially increased with ETEOS content. • FTIR, XRD and MAS NMR demonstrated the presence of ethyl groups into xerogels. • For ETEOS contents ≤30%, ethyl group acted as matrix modifier. • For ETEOS contents ≥30%, ethyl groups induced the formation of ordered domains

Synthesis and evaluation of 6-[{sup 11}C]Methoxy-3-[2- [1-(phenylmethyl)-4-piperidinyl]ethyl]-1,2-benzisoxazole as an in vivo radioligand for acetylcholinesterase

Energy Technology Data Exchange (ETDEWEB)

Brown-Proctor, Clive; Snyder, Scott E.; Sherman, Phillip S.; Kilbourn, Michael R. E-mail: mkilbour@umich.edu

1999-01-01

6-Methoxy-3-[2-[1-(phenylmethyl)-4-piperidinyl]ethyl]-1,2-benzisoxazole is a high affinity (K{sub i}=8.2 nM) reversible inhibitor of acetylcholinesterase (AChE). The carbon-11 labeled form was prepared in high (>97%) radiochemical purity and with specific activities of 37 {+-} 20 GBq/{mu}mol at end of synthesis, by the alkylation of the desmethyl precursor with [{sup 11}C]methyl trifluoromethanesulfonate in N,N-dimethylformamide at room temperature. In vivo studies in mice demonstrated good blood brain permeability but essentially uniform regional brain distribution. Thus, despite in vitro and in vivo activity as an AChE inhibitor, 6-[{sup 11}C]methoxy-3-[2-[1-(phenylmethyl)-4-piperidinyl]ethyl]-1, 2-benzisoxazole does not appear to be a good candidate for in vivo imaging studies of AChE in the mammalian brain.

Structure-activity relationship of daptomycin analogues with substitution at (2S, 3R) 3-methyl glutamic acid position.

Science.gov (United States)

Lin, Du'an; Lam, Hiu Yung; Han, Wenbo; Cotroneo, Nicole; Pandya, Bhaumik A; Li, Xuechen

2017-02-01

Daptomycin is a highly effective lipopeptide antibiotic against Gram-positive pathogens. The presence of (2S, 3R) 3-methyl glutamic acid (mGlu) in daptomycin has been found to be important to the antibacterial activity. However the role of (2S, 3R) mGlu is yet to be revealed. Herein, we reported the syntheses of three daptomycin analogues with (2S, 3R) mGlu substituted by (2S, 3R) methyl glutamine (mGln), dimethyl glutamic acid and (2S, 3R) ethyl glutamic acid (eGlu), respectively, and their antibacterial activities. The detailed synthesis of dimethyl glutamic acid was also reported. Copyright © 2016 Elsevier Ltd. All rights reserved.

Synthesis of carboxylic acids, esters, alcohols and ethers containing a tetrahydropyran ring derived from 6-methyl-5-hepten-2-one.

Science.gov (United States)

Hanzawa, Yohko; Hashimoto, Kahoko; Kasashima, Yoshio; Takahashi, Yoshiko; Mino, Takashi; Sakamoto, Masami; Fujita, Tsutomu

2012-01-01

3-hydroxy acids, 3-hydroxy-3,7-dimethyloct-6-enoic acid (1) and 3-hydroxy-2,2,3,7-tetramethyloct-6-enoic acid (2), were prepared from 6-methyl-5-hepten-2-one, and they were subsequently used to prepare (2,6,6-trimethyltetrahydropyran-2-yl)acetic acid (3) and 2-methyl-2-(2,6,6-trimethyltetrahydropyran-2-yl)propanoic acid (4), respectively, via cyclization with an acidic catalyst such as boron trifluoride diethyl etherate or iodine. The reaction of carboxylic acids 3 and 4 with alcohols, including methanol, ethanol, and 1-propanol, produced the corresponding methyl, ethyl, and propyl esters, which all contained a tetrahydropyran ring. Reduction of carboxylic acids 3 and 4 afforded the corresponding alcohols. Subsequent reactions of these alcohols with several acyl chlorides produced novel esters. The alcohols also reacted with methyl iodide and sodium hydride to provide novel ethers. A one-pot cyclization-esterification of 1 to produce esters containing a tetrahydropyran ring, using iodine as a catalyst, was also investigated.

Density, viscosity, and saturated vapor pressure of ethyl trifluoroacetate

International Nuclear Information System (INIS)

Huang, Zhixian; Jiang, Haiming; Li, Ling; Wang, Hongxing; Qiu, Ting

2015-01-01

Highlights: • Density of ethyl trifluoroacetate was measured and its thermal expansion coefficient was determined. • Viscosity of ethyl trifluoroacetate was measured and fitted to the Andrade equation. • Saturated vapor pressure of ethyl trifluoroacetate was reported. • The Clausius–Clapeyron equation was used to calculate the molar evaporation enthalpy of ethyl trifluoroacetate. - Abstract: The properties of ethyl trifluoroacetate (CF 3 COOCH 2 CH 3 ) were measured as a function of temperature: density (278.08 to 322.50) K, viscosity (293.45 to 334.32) K, saturated vapor pressure (293.35 to 335.65) K. The density data were fitted to a quadratic polynomial equation, and the viscosity data were regressed to the Andrade equation. The correlation coefficient (R 2 ) of equations for density and viscosity are 0.9997 and 0.9999, respectively. The correlation between saturated vapor pressures and temperatures was achieved with a maximum absolute relative deviation of 0.142%. In addition, the molar evaporation enthalpy in the range of T = (293.35 to 335.65) K was estimated by the Clausius–Clapeyron equation

Ethyl 2-{4-[(1,5-dibenzyl-2,4-dioxo-2,3,4,5-tetra-hydro-1H-1,5-benzo-diazepin-3-yl)meth-yl]-1H-1,2,3-triazol-1-yl}acetate.

Science.gov (United States)

Jabli, Hind; Kandri Rodi, Y; Ladeira, Sonia; Essassi, El Mokhtar; Ng, Seik Weng

2009-12-12

The reaction of 1,5-dibenzyl-3-propargyl-1,5-benzodiazepine-2,4-dione with ethyl azido-acetate in the presence of copper sulfate pentahydrate and sodium ascorbate leads to the formation of the title regioisomer, C(30)H(29)N(5)O(4), which features a phenyl-ene ring fused with a seven-membered diazepinyl ring. The latter ring adopts a boat conformation (with the methyl-triazolylacetate-bearing C atom as the prow and the fused-ring C atoms as the stern). The benzyl groups connected to the diazepinyl ring jprotrude from the sides; the methyl-triazolylacetate substituent occupies an axial position.

Synthesis and characterization of Ni{sub 0.7}Zn{sub 0.3}Fe{sub 2}O{sub 4} ferrospinel: performance evaluation for methyl and ethyl esterification; Sintese e caracterizacao do ferroespinelio Ni{sub 0,7}Zn{sub 0,3}Fe{sub 2}O{sub 4}: avaliacao de desempenho na esterificacao metilica e etilica

Energy Technology Data Exchange (ETDEWEB)

Mapossa, A.B., E-mail: mapossabenjox@gmail.com [Curso de Quimica, Dept. de Ciencias Naturais, Universidade Pedagogica de Mocambique, Delegacao de Manica, Chimoio (Mozambique); Dantas, J.; Diniz, V.C.S.; Costa, A.C.F.M. [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Programa de Pos-Graduacao em Ciencia e Engenharia de Materiais; Silva, M.R. [Universidade Federal de Itajuba (UNIFEI), MG (Brazil). Dept. de Fisica; Kiminami, R.H.G.A. [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil). Departamento de Engenharia de Materiais

2017-04-15

Ni{sub 0.7}Zn{sub 0.3}Fe{sub 2}O{sub 4} ferrospinel was synthesized by combustion and its catalytic performance in methyl and ethyl esterification of the soybean oil was investigated. The samples were characterized by X-ray diffraction, Rietveld refinement analysis, energy dispersive X-ray fluorescence spectroscopy, Fourier transform infrared spectroscopy, textural analysis, scanning electron microscopy, density by picnometry, particle size analysis, thermogravimetric analysis, magnetic measurements, and catalytic tests. The synthesis was efficient resulting in a ferrospinel with single phase Ni{sub 0.7}Zn{sub 0.3}Fe{sub 2}O{sub 4} with crystallite size of 20 nm, high surface area (86 m{sup 2}/g) and saturation magnetization of 18 emu/g. The ferrospinel had promising catalytic activity in both reaction conditions studied, being more active in the conversion of soybean oil to biodiesel in methyl esterification with an average conversion of 93.9±2.8%. (author)

Photoisomerization of ethyl ferulate: A solution phase transient absorption study

Science.gov (United States)

Horbury, Michael D.; Baker, Lewis A.; Rodrigues, Natércia D. N.; Quan, Wen-Dong; Stavros, Vasilios G.

2017-04-01

Ethyl ferulate (ethyl 4-hydroxy-3-methoxycinnamate) is currently used as a sunscreening agent in commercial sunscreen blends. Recent time-resolved gas-phase measurements have demonstrated that it possesses long-lived (>ns) electronic excited states, counterintuitive to what one might anticipate for an effective sunscreening agent. In the present work, the photodynamics of ethyl ferulate in cyclohexane, are explored using time-resolved transient electronic absorption spectroscopy, upon photoexcitation to the 11ππ∗ and 21ππ∗ states. We demonstrate that ethyl ferulate undergoes efficient non-radiative decay to repopulate the electronic ground state, mediated by trans-cis isomerization. These results strongly suggest that even mild perturbations induced by a non-polar solvent, as may be found in a closer-to-market sunscreen blend, may contribute to our understanding of ethyl ferulate's role as a sunscreening agent.

Use of a hand-portable gas chromatograph-toroidal ion trap mass spectrometer for self-chemical ionization identification of degradation products related to O-ethyl S-(2-diisopropylaminoethyl) methyl phosphonothiolate (VX)

Energy Technology Data Exchange (ETDEWEB)

Smith, Philip A., E-mail: Smith.Philip.A@dol.gov [Uniformed Services University of the Health Sciences, Department of Preventive Medicine and Biometrics, 4301 Jones Bridge Road, Bethesda, MD, 20814 (United States); Lepage, Carmela R. Jackson [Defence R and D Canada - Suffield, Box 400, Station Main, Medicine Hat, Alberta, T1A 8K6 (Canada); Savage, Paul B. [Brigham Young University, Department of Chemistry and Biochemistry, Provo, UT, 84602 (United States); Bowerbank, Christopher R.; Lee, Edgar D. [Torion Technologies Inc., 796 East Utah Valley Drive, Suite 200, American Fork, UT, 84003 (United States); Lukacs, Michael J. [Defence R and D Canada - Suffield, Box 400, Station Main, Medicine Hat, Alberta, T1A 8K6 (Canada)

2011-04-01

The chemical warfare agent O-ethyl S-(2-diisopropylaminoethyl) methyl phosphonothiolate (VX) and many related degradation products produce poorly diagnostic electron ionization (EI) mass spectra by transmission quadrupole mass spectrometry. Thus, chemical ionization (CI) is often used for these analytes. In this work, pseudomolecular ([M+H]{sup +}) ion formation from self-chemical ionization (self-CI) was examined for four VX degradation products containing the diisopropylamine functional group. A person-portable toroidal ion trap mass spectrometer with a gas chromatographic inlet was used with EI, and both fixed-duration and feedback-controlled ionization time. With feedback-controlled ionization, ion cooling (reaction) times and ion formation target values were varied. Evidence for protonation of analytes was observed under all conditions, except for the largest analyte, bis(diisopropylaminoethyl)disulfide which yielded [M+H]{sup +} ions only with increased fixed ionization or ion cooling times. Analysis of triethylamine-d{sub 15} provided evidence that [M+H]{sup +} production was likely due to self-CI. Analysis of a degraded VX sample where lengthened ion storage and feedback-controlled ionization time were used resulted in detection of [M+H]{sup +} ions for VX and several relevant degradation products. Dimer ions were also observed for two phosphonate compounds detected in this sample.

Use of a hand-portable gas chromatograph-toroidal ion trap mass spectrometer for self-chemical ionization identification of degradation products related to O-ethyl S-(2-diisopropylaminoethyl) methyl phosphonothiolate (VX)

International Nuclear Information System (INIS)

Smith, Philip A.; Lepage, Carmela R. Jackson; Savage, Paul B.; Bowerbank, Christopher R.; Lee, Edgar D.; Lukacs, Michael J.

2011-01-01

The chemical warfare agent O-ethyl S-(2-diisopropylaminoethyl) methyl phosphonothiolate (VX) and many related degradation products produce poorly diagnostic electron ionization (EI) mass spectra by transmission quadrupole mass spectrometry. Thus, chemical ionization (CI) is often used for these analytes. In this work, pseudomolecular ([M+H] + ) ion formation from self-chemical ionization (self-CI) was examined for four VX degradation products containing the diisopropylamine functional group. A person-portable toroidal ion trap mass spectrometer with a gas chromatographic inlet was used with EI, and both fixed-duration and feedback-controlled ionization time. With feedback-controlled ionization, ion cooling (reaction) times and ion formation target values were varied. Evidence for protonation of analytes was observed under all conditions, except for the largest analyte, bis(diisopropylaminoethyl)disulfide which yielded [M+H] + ions only with increased fixed ionization or ion cooling times. Analysis of triethylamine-d 15 provided evidence that [M+H] + production was likely due to self-CI. Analysis of a degraded VX sample where lengthened ion storage and feedback-controlled ionization time were used resulted in detection of [M+H] + ions for VX and several relevant degradation products. Dimer ions were also observed for two phosphonate compounds detected in this sample.

Extraction, Separation, and Purification of Blueberry Anthocyanin Using Ethyl Alcohol

Directory of Open Access Journals (Sweden)

Zhe Gao

2017-11-01

Full Text Available Blueberry contains many substances that are important to the human body and can prevent cardiovascular diseases, protect the retina, and soften blood vessels. Anthocyanin, which is extracted from blueberry, can activate the retina, strengthen vision, reduce serum cholesterol, triglyceride and high-density lipoprotein, and protect cell nucleus tissues from radical oxidation; hence, blueberry is of importance to scientists from different countries. In this study, anthocyanin was extracted and separated from blueberry using ethyl alcohol to investigate the effects of factors, such as ethyl alcohol volume ratio on anthocyanin extraction and separation technologies. The extracting solution was then purified using the macroreticular resin purification method to investigate the effects of ethyl alcohol concentration and eluent dosage on anthocyanin extraction during purification. The research results demonstrated that 60 % ethyl alcohol volume fraction, 1 : 10 mass ratio of solid to liquid, and 60 °C ultrasonic temperature were the best conditions for anthocyanin extraction. The best purification conditions were 95 % ethyl alcohol, which had been acidized by 0.3 % hydrochloric acid and 70 ml of eluent. This work provides a reference for the application of ethyl alcohol in anthocyanin extraction.

Synthesis of acetic acid by catalytic oxidation of butenes-2. Synthesis of acetic acid from sec. -butyl alcohol and methyl ethyl ketone in vapor-phase catalytic oxidation

Energy Technology Data Exchange (ETDEWEB)

Yamashita, T.; Matsuzawa, Y.; Ninagawa, S.

1977-11-01

Eleven binary catalysts containing vanadium pentoxide (V/sub 2/O/sub 5/), 17 binary catalysts containing cobalt oxide (Co/sub 3/O/sub 4/), and 18 ternary catalysts containing both V/sub 2/O/sub 5/ and Co/sub 3/O/sub 4/ were screened for the stepwise conversion of sec.-butanol to methyl ethyl ketone (MEK) and acetic acid. Of the binary catalysts, 4:1 Rh/V and Co/V binary oxides gave the best acetic acid yields. With the Co/V catalyst, the selectivity for MEK increased rapidly as the cobalt content of the catalyst increased above 50%, reaching 81% at 226/sup 0/C and 90% conversion on 9:1 Co/V oxide. The 9:1 Co/V catalyst also yielded acetaldehyde from ethanol with 98% selectivity at 210/sup 0/C and acetone from isopropanol with 98% selectivity at 200/sup 0/C, but dehydrated tert.-butanol to isobutene. V/Cr and V/Sb binary oxides were the most effective catalysts for the oxidation of MEK to acetic acid, with 78-88% selectivities at 100% conversion at 260/sup 0/C. Of the ternary oxides tested for the one-step conversion of sec.-butanol to acetic acid, a 6:2:2 Co/V/Al catalyst gave best results, (i.e., 34% selectivity for acetic acid (45% for total acids) at 100% conversion and 68% selectivity (90% for total acids) at 50Vertical Bar3< conversion). Graphs, tables, and 21 references.

Method for determination of methyl tert-butyl ether and its degradation products in water

Science.gov (United States)

Church, C.D.; Isabelle, L.M.; Pankow, J.F.; Rose, D.L.; Tratnyek, P.G.

1997-01-01

An analytical method is described that can detect the major alkyl ether compounds that are used as gasoline oxygenates (methyl tert-butyl ether, MTBE; ethyl tert-butyl ether, ETBE; and tert-amyl methyl ether, TAME) and their most characteristic degradation products (tert-butyl alcohol, TBA; tert-butyl formate, TBF; and tert-amyl alcohol, TAA) in water at sub-ppb concentrations. The new method involves gas chromatography (GC) with direct aqueous injection (DAI) onto a polar column via a splitless injector, coupled with detection by mass spectrometry (MS). DAI-GC/MS gives excellent agreement with conventional purge-and-trap methods for MTBE over a wide range of environmentally relevant concentrations. The new method can also give simultaneous identification of polar compounds that might occur as degradation products of gasoline oxygenates, such as TBA, TBF, TAA, methyl acetate, and acetone. When the method was applied to effluent from a column microcosm prepared with core material from an urban site in New Jersey, conversion of MTBE to TBA was observed after a lag period of 35 days. However, to date, analyses of water samples from six field sites using the DAI-GC/MS method have not produced evidence for the expected products of in situ degradation of MTBE.An analytical method is described that can detect the major alkyl ether compounds that are used as gasoline oxygenates (methyl tert-butyl ether, MTBE; ethyl tert-butyl ether, ETBE; and tert-amyl methyl ether, TAME) and their most characteristic degradation products (tert-butyl alcohol, TBA; tert-butyl formate, TBF; and tert-amyl alcohol, TAA) in water at sub-ppb concentrations. The new method involves gas chromatography (GC) with direct aqueous injection (DAI) onto a polar column via a splitless injector, coupled with detection by mass spectrometry (MS). DAI-GC/MS gives excellent agreement with conventional purge-and-trap methods for MTBE over a wide range of environmentally relevant concentrations. The new method

2,6-Bis(9-ethyl-9H-carbazolylmethylenecyclohexanone

Directory of Open Access Journals (Sweden)

Abdullah M. Asiri

2009-10-01

Full Text Available The title compound, 2,6-bis(ethyl-9-ethyl-9H-carbazolylmethylenecyclohexanone has been synthesized by condensation of 9-ethylcarbazole-3-aldehyde and cyclohexanone in ethanol in the presence of pyridine. The structure of this new compound was confirmed by elemental analysis, IR, 1H NMR, 13C NMR and EI-MS spectral analysis.

19 CFR 10.99 - Importation of ethyl alcohol for nonbeverage purposes.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Importation of ethyl alcohol for nonbeverage purposes. 10.99 Section 10.99 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND... Provisions Ethyl Alcohol § 10.99 Importation of ethyl alcohol for nonbeverage purposes. (a) If claim is made...

SYNTHESIS OF FATTY ACID ETHYL ESTER FROM CHICKEN FAT ...

African Journals Online (AJOL)

eobe

synthesis of fatty acid ethyl ester from chicken fat waste using ZnO/SiO fatty acid ethyl ester ... obtained in the range of 56−88%and a second order quadratic polynomial regression model that established the ... Transesterification is a chemical.

Broadband dynamics in neat 4-methyl-3-heptanol and in mixtures with 2-ethyl-1-hexanol

DEFF Research Database (Denmark)

Hecksher, Tina; Olsen, Niels Boye; Bauer, S

2013-01-01

place on similar time scales in contrast to the situation for the structural isomer 2-ethyl-1-hexanol (2E1H) [S. Schildmann et al. , J. Chem. Phys.135, 174511 (2011)]. This indicates a very weak decoupling of Debye-like and structural relaxation which was further probed using volume expansivity...... experiments. Shear viscosity as well as diffusometry measurements were performed and the data were analyzed in terms of the Debye-Stokes-Einstein equations. In mixtures of 4M3H with 2E1H the Debye-like process becomes much stronger and for 2E1H mole fraction of more than 25% the behavior of this alcohol...... is rapidly approached. This finding is interpreted to indicate that the ring-like supramolecular structures in 4M3H become energetically unfavorable when adding 2E1H, an alcohol that tends to form chain-like molecular aggregates. The concentration dependence of the Kirkwood factor in these mixtures displays...

Thermal Properties of Methyl Ester-Containing Poly(2-oxazolines

Directory of Open Access Journals (Sweden)

Petra J. M. Bouten

2015-10-01

Full Text Available This paper describes the synthesis and thermal properties in solution and bulk of poly(2-alkyl-oxazolines (PAOx containing a methyl ester side chain. Homopolymers of 2-methoxycarbonylethyl-2-oxazoline (MestOx and 2-methoxycarbonylpropyl-2-oxazoline (C3MestOx, as well as copolymers with 2-ethyl-2-oxazoline (EtOx and 2-n-propyl-2-oxazoline (nPropOx, with systematic variations in composition were prepared. The investigation of the solution properties of these polymers revealed that the cloud point temperatures (TCPs could be tuned in between 24 °C and 108 °C by variation of the PAOx composition. To the best of our knowledge, the TCPs of PMestOx and PC3MestOx are reported for the first time and they closely resemble the TCPs of PEtOx and PnPropOx, respectively, indicating similar hydrophilicity of the methyl ester and alkyl side chains. Furthermore, the thermal transitions and thermal stability of these polymers were investigated by DSC and TGA measurements, respectively, revealing amorphous polymers with glass transition temperatures between -1 °C and 54 °C that are thermally stable up to >300 °C.

Synthesis and Physical and Chemical Properties of Hypergolic Chemicals such as N,N,N-Trimethylhydrazinium and 1-Ethyl-4-Methyl-1,2,4-Triazolium Salts

Directory of Open Access Journals (Sweden)

Young-Seok Kim

2015-12-01

Full Text Available Hypergolic chemicals N,N,N-trimethylhydrazinium iodide, [TMH]+[I]−, and 1-ethyl-4-methyl-1,2,4-triazolium iodide, [EMT]+[I]− were firstly synthesized by nucleophilic substitution (SN2. The successful synthesis of hypergolic chemicals [TMH]+[I]− and [EMT]+[I]− was confirmed by IR and 1H-NMR spectroscopy and, GC-mass spectrometry. Subsequently the hypergolic chemicals [TMH]+[X]− (X = CN−, N3−, NO3−, NO2−, ClO4−, AlCl4− were prepared via an ion exchange reaction from [TMH]+[I]− and [EMT]+[I]−, respectively. After that, a mixture of hypergolic chemicals was prepared by dissolving the synthesized hypergolic chemicals in 2-hydroxyethylhydrazine (HOCH2CH2NHNH2. The physical and chemical properties of the mixture such as decomposition temperature (Td, density (d, viscosity (η, and decomposition energy (ΔHd was then evaluated to determine suitability for use as liquid rocket fuels. The ignition delay (ID time of the mixture of hypergolic chemicals with [TMH]+[N3]− and [TMH]+[CN]− using H2O2 as an oxidizer was determined as 55.6 ms and 97.4 ms; respectively. The ID time of the mixture of hypergolic chemicals with [EMT]+[N3]−; [EMT]+[CN]−; [EMT]+[AlCl4]−; and [EMT]+[I]− using H2O2 as an oxidizer was also determined as 18.0 ms; 32.6 ms; 27.6 ms; and 7.96 ms; respectively. The synthesized mixture of hypergolic chemicals could thus be used as a rocket propellant liquid fuel.

Simulating structure and dynamics in small droplets of 1-ethyl-3-methylimidazolium acetate

Science.gov (United States)

Brehm, Martin; Sebastiani, Daniel

2018-05-01

To investigate the structure and dynamics of small ionic liquid droplets in gas phase, we performed a DFT-based ab initio molecular dynamics study of several 1-ethyl-3-methylimidazolium acetate clusters in vacuum as well as a bulk phase simulation. We introduce an unbiased criterion for average droplet diameter and density. By extrapolation of the droplet densities, we predict the experimental bulk phase density with a deviation of only a few percent. The hydrogen bond geometry between cations and anions is very similar in droplets and bulk, but the hydrogen bond dynamics is significantly slower in the droplets, becoming slower with increasing system size, with hydrogen bond lifetimes up to 2000 ps. From a normal mode analysis of the trajectories, we identify the modes of the ring proton C-H stretching, which are strongly affected by hydrogen bonding. From analyzing these, we find that the hydrogen bond becomes weaker with increasing system size. The cations possess an increased concentration inside the clusters, whereas the anions show an excess concentration on the outside. Almost all anions point towards the droplet center with their carboxylic groups. Ring stacking is found to be a very important structural motif in the droplets (as in the bulk), but side chain interactions are only of minor importance. By using Voronoi tessellation, we define the exposed droplet surface and find that it consists mainly of hydrogen atoms from the cation's and anion's methyl and ethyl groups. Polar atoms are rarely found on the surface, such that the droplets appear completely hydrophobic on the outside.

New results in pulsed laser deposition of poly-methyl-methacrylate thin films

International Nuclear Information System (INIS)

Cristescu, R.; Socol, G.; Mihailescu, I.N.; Popescu, M.; Sava, F.; Ion, E.; Morosanu, C.O.; Stamatin, I.

2003-01-01

Thin organic films based on poly-methyl-methacrylate (PMMA) polymer have been obtained by pulsed laser deposition (PLD) on silicon substrates. The films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and Raman spectroscopy (RS). We observed that the film composition and structure depend on the laser fluence and on the temperature of the substrate during deposition

[Determination of organotin compounds in plastic products by GC/MS after ethyl derivatization with sodium tetraethylborate].

Science.gov (United States)

Ohno, Hiroyuki; Suzuki, Masako; Nakashima, Shigehito; Aoyama, Taiki; Mitani, Kazunori

2002-08-01

A simultaneous determination method for 9 organotin compounds in polyvinyl chloride (PVC) and silicone products used as kitchen utensils and food packages was developed using ethyl derivatization with sodium tetraethylborate (NaBEt4). Organotin compounds were extracted with acetone-hexane (3:7) from the samples after acidification and the extract was filtered and concentrated at under 40 degrees C. After centrifugal separation, these compounds were derivatized with 2% NaBEt4 solution and determined by GC/MS. This method was applicable for simple routine analysis. Recoveries of spiked compounds were 49.1-118.1% for 3 PVC products and 88.8-102.2% for a siliconized paper. Monooctyltin, dioctyltin and trioctyltin compounds were found in all PVC food containers at the levels of 123-1,380 micrograms/g, 1,770-13,200 micrograms/g and 6.6-139 micrograms/g, respectively. They also were found in 3 gloves, 5 spouts, 1 hose and 5 pipes. Some PVC products contained monomethyltin, dimethyltin, trimethyltin, monobutyltin and dibutyltin compounds at the levels of 97.3-433 micrograms/g, 96.5-5,120 micrograms/g, 8.5-24.9 micrograms/g, 1.2-852 micrograms/g and 1.2-29.4 micrograms/g, respectively.

Evaluation of CP sil 8 film thickness for the capillary GC analysis of methyl mercury

DEFF Research Database (Denmark)

Petersen, Jens Højslev; Drabæk, Iver

1992-01-01

Different commercially available CP-Sil 8 CB capillary columns have been tested with a mixed standard containing methyl mercury chloride, ethyl mercury chloride and a stable nonpolar chlorinated hydrocarbon. The aim of the study was to see whether the columns tested could be used without special...... available insert for on-column injections on wide bore columns, and a 5.35 mum thick stationary phase. It was concluded that this CP Sil 8 CB column gave good results although minor interactions between the organo-mercury compounds and the column could be seen....

Undergraduate Analytical Chemistry Experiment: The Determination of Formation Constants for Acetate and Mono-and Dichloroacetate Salts of Primary, Secondary, and Tertiary Methyl-and Ethylamines

Science.gov (United States)

D'Amelia, Ronald P.; Chiang, Stephanie; Pollut, Stephanie; Nirode, William F.

2014-01-01

The formation and the hydrolysis of organic salts produced by the titration of a 0.1 M solution of the following amines: methyl-, dimethyl-, trimethyl-, ethyl-, diethyl-, and triethylamine with a 0.1 M solution of acetic, chloroacetic, and dichloracetic acids are studied. The pK[subscript b] of the amine and the pH at the end point were determined…

Thermal decomposition mechanism of 1-ethyl-3-methylimidazolium bromide ionic liquid.

Science.gov (United States)

Chambreau, Steven D; Boatz, Jerry A; Vaghjiani, Ghanshyam L; Koh, Christine; Kostko, Oleg; Golan, Amir; Leone, Stephen R

2012-06-21

In order to better understand the volatilization process for ionic liquids, the vapor evolved from heating the ionic liquid 1-ethyl-3-methylimidazolium bromide (EMIM(+)Br(-)) was analyzed via tunable vacuum ultraviolet photoionization time-of-flight mass spectrometry (VUV-PI-TOFMS) and thermogravimetric analysis mass spectrometry (TGA-MS). For this ionic liquid, the experimental results indicate that vaporization takes place via the evolution of alkyl bromides and alkylimidazoles, presumably through alkyl abstraction via an S(N)2 type mechanism, and that vaporization of intact ion pairs or the formation of carbenes is negligible. Activation enthalpies for the formation of the methyl and ethyl bromides were evaluated experimentally, ΔH(‡)(CH(3)Br) = 116.1 ± 6.6 kJ/mol and ΔH(‡)(CH(3)CH(2)Br) = 122.9 ± 7.2 kJ/mol, and the results are found to be in agreement with calculated values for the S(N)2 reactions. Comparisons of product photoionization efficiency (PIE) curves with literature data are in good agreement, and ab initio thermodynamics calculations are presented as further evidence for the proposed thermal decomposition mechanism. Estimates for the enthalpy of vaporization of EMIM(+)Br(-) and, by comparison, 1-butyl-3-methylimidazolium bromide (BMIM(+)Br(-)) from molecular dynamics calculations and their gas phase enthalpies of formation obtained by G4 calculations yield estimates for the ionic liquids' enthalpies of formation in the liquid phase: ΔH(vap)(298 K) (EMIM(+)Br(-)) = 168 ± 20 kJ/mol, ΔH(f, gas)(298 K) (EMIM(+)Br(-)) = 38.4 ± 10 kJ/mol, ΔH(f, liq)(298 K) (EMIM(+)Br(-)) = -130 ± 22 kJ/mol, ΔH(f, gas)(298 K) (BMIM(+)Br(-)) = -5.6 ± 10 kJ/mol, and ΔH(f, liq)(298 K) (BMIM(+)Br(-)) = -180 ± 20 kJ/mol.

Glucose utilization in the brain during acute seizure is a useful biomarker for the evaluation of anticonvulsants: effect of methyl ethyl ketone in lithium-pilocarpine status epilepticus rats

International Nuclear Information System (INIS)

Yamada, Akifumi; Momosaki, Sotaro; Hosoi, Rie; Abe, Kohji; Yamaguchi, Masatoshi; Inoue, Osamu

2009-01-01

Enhancement of glucose utilization in the brain has been well known during acute seizure in various kinds of animal model of epilepsy. This enhancement of glucose utilization might be related to neural damage in these animal models. Recently, we found that methyl ethyl ketone (MEK) had both anticonvulsive and neuroprotective effects in lithium-pilocapine (Li-pilo) status epilepticus (SE) rat. In this article, we measured the uptake of [ 14 C]2-deoxyglucose ([ 14 C]DG) in the Li-pilo SE and Li-pilo SE with MEK rat brain in order to assess whether the glucose utilization was a useful biomarker for the detection of efficacy of anticonvulsive compounds. Significant increase of [ 14 C]DG uptake (45 min after the injection) in the cerebral cortex, hippocampus, amygdala and thalamus during acute seizure induced by Li-pilo were observed. On the other hand, the initial uptake of [ 14 C]DG (1 min after the injection) in the Li-pilo SE rats was not different from the control rats. Therefore, the enhancement of glucose metabolism during acute seizure was due to the facilitation of the rate of phosphorylation process of [ 14 C]DG in the brain. Pretreatment with MEK (8 mmol/kg) completely abolished the enhancement of glucose utilization in the Li-pilo SE rats. The present results indicated that glucose utilization in the brain during acute seizure might be a useful biomarker for the evaluation of efficacy of anticonvulsive compounds.

Glucose utilization in the brain during acute seizure is a useful biomarker for the evaluation of anticonvulsants: effect of methyl ethyl ketone in lithium-pilocarpine status epilepticus rats

Energy Technology Data Exchange (ETDEWEB)

Yamada, Akifumi [Division of Health Sciences, Graduate School of Medicine, Osaka University, Osaka, 565-0871 (Japan); Momosaki, Sotaro; Hosoi, Rie [Division of Health Sciences, Graduate School of Medicine, Osaka University, Osaka, 565-0871 (Japan); Abe, Kohji [Division of Health Sciences, Graduate School of Medicine, Osaka University, Osaka, 565-0871 (Japan); Developmental Research Laboratories, Shionogi and Co., Ltd., Toyonaka, Osaka, 561-0825 (Japan); Yamaguchi, Masatoshi [Faculty of Pharmaceutical Sciences, Fukuoka University, Johnan, Fukuoka 814-0180 (Japan); Inoue, Osamu [Division of Health Sciences, Graduate School of Medicine, Osaka University, Osaka, 565-0871 (Japan)

2009-11-15

Enhancement of glucose utilization in the brain has been well known during acute seizure in various kinds of animal model of epilepsy. This enhancement of glucose utilization might be related to neural damage in these animal models. Recently, we found that methyl ethyl ketone (MEK) had both anticonvulsive and neuroprotective effects in lithium-pilocapine (Li-pilo) status epilepticus (SE) rat. In this article, we measured the uptake of [{sup 14}C]2-deoxyglucose ([{sup 14}C]DG) in the Li-pilo SE and Li-pilo SE with MEK rat brain in order to assess whether the glucose utilization was a useful biomarker for the detection of efficacy of anticonvulsive compounds. Significant increase of [{sup 14}C]DG uptake (45 min after the injection) in the cerebral cortex, hippocampus, amygdala and thalamus during acute seizure induced by Li-pilo were observed. On the other hand, the initial uptake of [{sup 14}C]DG (1 min after the injection) in the Li-pilo SE rats was not different from the control rats. Therefore, the enhancement of glucose metabolism during acute seizure was due to the facilitation of the rate of phosphorylation process of [{sup 14}C]DG in the brain. Pretreatment with MEK (8 mmol/kg) completely abolished the enhancement of glucose utilization in the Li-pilo SE rats. The present results indicated that glucose utilization in the brain during acute seizure might be a useful biomarker for the evaluation of efficacy of anticonvulsive compounds.

Effects of (+/-)-4-[[2-(1-methyl-2-pyrrolidinyl)ethyl]thio]phenol hydrochloride (SIB-1553A), a selective ligand for nicotinic acetylcholine receptors, in tests of visual attention and distractibility in rats and monkeys.

Science.gov (United States)

Terry, A V; Risbrough, V B; Buccafusco, J J; Menzaghi, F

2002-04-01

Nicotine, a nonselective ligand for nicotinic acetylcholine receptors (nAChRs), has been shown to improve attention and reduce distractibility in humans. Although the numerous side effects induced by nicotine prevent its use as a therapeutic agent, it is hypothesized that subtype-selective nAChR ligands may offer a potential therapeutic benefit to humans with attention deficits. In this study, we evaluated the attention-enhancing properties of (+/-)-4-[[2-(1-methyl-2-pyrrolidinyl)ethyl]thio]phenol hydrochloride (SIB-1553A), a ligand selective for neuronal nAChRs with predominant activity at the human beta 4 subtype. SIB-1553A was evaluated in a test of attention (i.e., five-choice serial reaction time task or SRTT) and distractibility (i.e., delayed matching to sample task with distractor or DMTS-D) in adult rats and monkeys, respectively. SIB-1553A did not improve SRTT performance in normal rats, but reversed deficits induced by the N-methyl-D-aspartate (NMDA) antagonist dizocilpine. In the DMTS-D, SIB-1553A improved accuracy across several doses at the short delay intervals, which were affected most by distracting stimuli in adult monkeys. Subsequent testing with optimal doses for each monkey was also associated with significant improvements in DMTS-D accuracy at short delays, indicating the reproducibility of the drug effect. In both species, SIB-1553A had no significant effects on latencies for sample or choice selection and was not associated with adverse effects at efficacious doses. Although it remains to be further demonstrated, SIB-1553A may act through combined nicotinic and non-nicotinic mechanisms. Collectively, the present data suggest that in specific conditions SIB-1553A may improve certain aspects of attentional function in young adult rats and nonhuman primates without adverse side effects.

Methyl-Analyzer--whole genome DNA methylation profiling.

Science.gov (United States)

Xin, Yurong; Ge, Yongchao; Haghighi, Fatemeh G

2011-08-15

Methyl-Analyzer is a python package that analyzes genome-wide DNA methylation data produced by the Methyl-MAPS (methylation mapping analysis by paired-end sequencing) method. Methyl-MAPS is an enzymatic-based method that uses both methylation-sensitive and -dependent enzymes covering >80% of CpG dinucleotides within mammalian genomes. It combines enzymatic-based approaches with high-throughput next-generation sequencing technology to provide whole genome DNA methylation profiles. Methyl-Analyzer processes and integrates sequencing reads from methylated and unmethylated compartments and estimates CpG methylation probabilities at single base resolution. Methyl-Analyzer is available at http://github.com/epigenomics/methylmaps. Sample dataset is available for download at http://epigenomicspub.columbia.edu/methylanalyzer_data.html. fgh3@columbia.edu Supplementary data are available at Bioinformatics online.

Synthesis of Some Novel Biologically Active Disperse Dyes Derived from 4-Methyl-2,6-dioxo-1-propyl-1,2,5,6-tetrahydro-pyridine-3-carbonitrile as Coupling Component and Their Colour Assessment on Polyester Fabrics

Directory of Open Access Journals (Sweden)

Mohamed H. Elnagdi

2012-07-01

Full Text Available A series of novel azo-disperse dyes containing alkylhydrazonopyridinone structures were synthesized. 4-Methyl-2,6-dioxo-1-propyl-1,2,5,6-tetrahydropyridine-3-carbonitrile (8 is synthesized by one-pot synthesis using ethyl cyanoacetate, propylamine, and ethyl acetoacetate. Compound 8 is then coupled with aromatic and heteroaromatic diazonium salts to afford the corresponding aryl- and heteroaryl-4-methyl-2,6-dioxo-1-propyl-1,2,5,6-tetrahydropyridine-3-carbonitriles 12a,b and 13a–c. Structural assignments to the dyes were made using NMR spectroscopic methods. A high temperature dyeing method was employed to apply these dyes to polyester fabrics. Most of the dyed fabrics tested displayed very good light fastness levels and good wash fastness. Finally, the biological activity of the prepared dyes against Gram positive bacteria and Gram negative bacteria were evaluated.

Biodegradation and detoxification of chlorimuron-ethyl by Enterobacter ludwigii sp. CE-1.

Science.gov (United States)

Pan, Xiong; Wang, Saige; Shi, Nan; Fang, Hua; Yu, Yunlong

2018-04-15

The application of the herbicide chlorimuron-ethyl has a lasting toxic effect on some succession crops. Here, a bacterium capable of utilizing chlorimuron-ethyl as the sole source of nitrogen was isolated from the contaminated soil and was identified as Enterobacter ludwigii sp. CE-1, and its detoxification and degradation of the herbicide were then examined. The biodegradation of chlorimuron-ethyl by the isolate CE-1 was significantly accelerated with increasing concentration (1-10mg/l) and temperature (20-40°C). The optimal pH for the degradation of chlorimuron-ethyl by the isolate CE-1 was pH 7.0. A pathway for the biodegradation of chlorimuron-ethyl by the isolate CE-1 was proposed, in which it could be first converted into 2-amino-4-chloro-6-methoxypyrimidine and an intermediate product by the cleavage of the sulfonylurea bridge and then transformed into saccharin via hydrolysis and amidation. The plant height and fresh weight of corn that had been incubated in nutrient solution containing 0.2mg/l of chlorimuron-ethyl significantly recovered to 83.9% and 83.1% compared with those in the uninoculated control, although the root growth inhibition of chlorimuron-ethyl could not be alleviated after inoculation for 14 d. The results indicate that the isolate CE-1 is a promising bacterial resource for the biodegradation and detoxification of chlorimuron-ethyl. Copyright © 2017 Elsevier Inc. All rights reserved.

Effect of TMAH Etching Duration on the Formation of Silicon Nano wire Transistor Patterned by AFM Nano lithography

International Nuclear Information System (INIS)

Hutagalung, S.D.; Lew, K.C.

2012-01-01

Atomic force microscopy (AFM) lithography was applied to produce nano scale pattern for silicon nano wire transistor fabrication. This technique takes advantage of imaging facility of AFM and the ability of probe movement controlling over the sample surface to create nano patterns. A conductive AFM tip was used to grow the silicon oxide nano patterns on silicon on insulator (SOI) wafer. The applied tip-sample voltage and writing speed were well controlled in order to form pre-designed silicon oxide nano wire transistor structures. The effect of tetra methyl ammonium hydroxide (TMAH) etching duration on the oxide covered silicon nano wire transistor structure has been investigated. A completed silicon nano wire transistor was obtained by removing the oxide layer via hydrofluoric acid etching process. The fabricated silicon nano wire transistor consists of a silicon nano wire that acts as a channel with source and drain pads. A lateral gate pad with a nano wire head was fabricated very close to the channel in the formation of transistor structures. (author)

Phase diagram measurements by Heat-flux DSC and thermodynamic calculations of the mixture of the Esters Ethyl undecanoate (C13H26O2) and Ethyl tridecanoate (C15H30O2)

NARCIS (Netherlands)

Schaftenaar, H.P.C.

2006-01-01

In this report a phase diagram is determined by heat flux DSC of the binary mixture Ethyl undecanoate and Ethyl tridecanoate. Our hypothesis for equilibrium phase behaviour is that the components Ethyl undecanoate and Ethyl tridecanoate do have the same crystal form and they have restricted

Synthesis of carbon-14 labelled ethyl chloride

International Nuclear Information System (INIS)

Kanski, R.

1976-01-01

A new efficient method of synthesis of ethyl chloride (1,2- 14 C), based on the Ba 14 CO 3 and dry hydrogen chloride as starting materials has been developed and described. Addition of the hydrogen chloride to ethylene (1,2- 14 C), obtained from Ba 14 CO 3 , has been carried out in the presence of the AlCl 3 as catalyst. The outlined method leads to ethyl chloride (1,2- 14 C) of high specific activity. The radiochemical yield of the reaction based on the activity of barium carbonate used was 72%. (author)

Synthesis, Analgesic and Anti-inflammatory Activities of 3- Ethyl-2 ...

African Journals Online (AJOL)

4(3H)-ones and evaluate them for their analgesic and anti-inflammatory activities. Methods: The compounds, 3-ethyl-2-substituted amino-quinazolin-4(3H)-ones, were synthesized by reacting the amino group of 3-ethyl-2-hydrazino ...

Topical ethyl chloride fine spray. Does it have any antimicrobial activity?

International Nuclear Information System (INIS)

Burney, K.; Bowker, K.; Reynolds, R.; Bradley, M.

2006-01-01

Aim: The aim of this study was to assess whether ethyl chloride fine spray (Cryogesic[reg]) has antimicrobial activity. Material and methods: Blood agar plates supplemented with 5% horse blood were inoculated with five different organisms, coagulase-negative staphylococci (CNS), methicillin-sensitive Staphylococcus aureus (MSSA), methicillin-resistant S. aureus (MRSA), Streptococcus pyogenes and Enterococcus faecalis. The plates were assessed for growth inhibition at 24 and 48 h by the microbiologist and compared with the non-sprayed control plates. Results: The model showed a highly significant (p < 0.0001) reduction in bacterial count for the plates treated with fine ethyl chloride spray. The estimate of the percentage of bacteria remaining after spraying with ethyl chloride was 42.7%, with a 95% confidence interval of 35.9-50.9%. There was no evidence that the effect of ethyl chloride fine spray was different for the different organisms (p = 0.49). Conclusion: The use of ethyl chloride shows bacterial count reduction but the clinical implication of this needs to be determined. The authors postulate that any statistically significant reduction can only be helpful in reducing the infection rates. This coupled with the already proven local anaesthetic effects of ethyl chloride will make it an important tool for procedures like arthrocentesis and venepunctures

Topical ethyl chloride fine spray. Does it have any antimicrobial activity?

Energy Technology Data Exchange (ETDEWEB)

Burney, K.; Bowker, K.; Reynolds, R.; Bradley, M

2006-12-15

Aim: The aim of this study was to assess whether ethyl chloride fine spray (Cryogesic[reg]) has antimicrobial activity. Material and methods: Blood agar plates supplemented with 5% horse blood were inoculated with five different organisms, coagulase-negative staphylococci (CNS), methicillin-sensitive Staphylococcus aureus (MSSA), methicillin-resistant S. aureus (MRSA), Streptococcus pyogenes and Enterococcus faecalis. The plates were assessed for growth inhibition at 24 and 48 h by the microbiologist and compared with the non-sprayed control plates. Results: The model showed a highly significant (p < 0.0001) reduction in bacterial count for the plates treated with fine ethyl chloride spray. The estimate of the percentage of bacteria remaining after spraying with ethyl chloride was 42.7%, with a 95% confidence interval of 35.9-50.9%. There was no evidence that the effect of ethyl chloride fine spray was different for the different organisms (p = 0.49). Conclusion: The use of ethyl chloride shows bacterial count reduction but the clinical implication of this needs to be determined. The authors postulate that any statistically significant reduction can only be helpful in reducing the infection rates. This coupled with the already proven local anaesthetic effects of ethyl chloride will make it an important tool for procedures like arthrocentesis and venepunctures.

Correlation and prediction of mixing thermodynamic properties of ester-containing systems: Ester + alkane and ester + ester binary systems and the ternary dodecane + ethyl pentanoate + ethyl ethanoate

International Nuclear Information System (INIS)

Pérez, Noelia; Fernández, Luís; Ortega, Juan; Toledo, Francisco J.; Wisniak, Jaime

2012-01-01

Highlights: ► Excess enthalpies and volumes were measured for ester–ester–alkane. ► Mixing behaviour for ester–ester, ester–alkane and ester–ester–alkane are analyzed. ► Correlations with a new polynomial model reproduce well the mixing properties. ► UNIFAC predictions for h E result acceptable excluding the ester–ester mixtures. - Abstract: Excess thermodynamic properties V m E and H m E , have been measured for the ternary mixture dodecane + ethyl pentanoate + ethyl ethanoate and for the corresponding binaries dodecane + ethyl pentanoate, dodecane + ethyl ethanoate, ethyl pentanoate + ethyl ethanoate at 298.15 K. All mixtures show endothermic and expansive effects. Experimental results are correlated with a suitable equation whose final form for the excess ternary quantity M E contains the particular contributions of the three binaries (i–j) and a last term corresponding to the ternary, all of them obtained considering fourth-order interactions. The fit goodness for all mixtures is good and comparable to others equations taken from the literature. In this work the dissolution model for the binaries and ternary is analyzed with a special attention to ester–ester binaries whose behaviour is discussed. The application of the UNIFAC group contribution model to estimate the H m E yields acceptable results for the binaries (with the exception of ester–ester) and for the ternary mixture.

Combustion by synthesis in pilot scale of nanocatalyst Ni{sub 0,5}Zn{sub 0,5}Fe{sub 2}O{sub 4} and the performance in methyl and ethyl esterification to obtaining biodiesel; Sintese por combustao em escala piloto do nanocatalisador Ni{sub 0,5}Zn{sub 0,5}Fe{sub 2}O{sub 4} e seu desempenho na esterificacao metilica e etilica para obtencao de biodiesel

Energy Technology Data Exchange (ETDEWEB)

Moura, T.F.B.; Barros, A.B.S.; Dantas, J.; Pereira, K.R.O.; Vasconcelos, E.V.; Costa, A.C.F.M., E-mail: thalesnatuba@hotmail.com [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais

2016-07-01

To produce biodiesel from the use of catalysts is necessary because help in getting better reaction yields and currently magnetic materials has gained prominence for this application. This study aimed to prepare the nanocatalyst Ni{sub 0,5}Zn{sub 0,5}Fe{sub 2}O{sub 4} in laboratory scale, to evaluate their performance in methyl AND ethyl esterification using acidified soybean oil as raw material. The samples were synthesized by reaction in a combustion reactor with a production capacity of 200g / batch and characterized by XRD, TG and EDX. The catalytic tests took place at a temperature of 180 ° C / 1h, molar ratio 1:12, 2% nanocatalyst and analyzed by gas chromatography. Samples showed the major phase of the inverse spinel with an average crystallite size of 20.25 nm and traces of segregated phases of Fe{sub 2}O{sub 3} and ZnO. The values of the detected oxides were 68.01% for Fe2O3, 16.57% for NiO and 15.28% for ZnO, values that are close to the calculated theoretical. The sample showed total mass loss equal to 6.5%, demonstrating its excellent thermal stability. The biodiesel conversion results were 84.11 and 73.74% for methyl ethyl route, respectively. Therefore, the synthesized material has catalytic potential in the tested reaction and could be a promising material for both assessed routes. (author)

Binding of ethyl pyruvate to bovine serum albumin: Calorimetric, spectroscopic and molecular docking studies

Energy Technology Data Exchange (ETDEWEB)

Pathak, Mallika [Department of Chemistry, Miranda House, University of Delhi, Delhi 11007 (India); Mishra, Rashmi; Agarwala, Paban K. [Department of Radiation Genetics and Epigenetics, Division of Radioprotective Drug Development Research, Institute of Nuclear Medicine and Allied Sciences, Delhi 110054 (India); Ojha, Himanshu, E-mail: himanshu.drdo@gmail.com [Department of Radiation Genetics and Epigenetics, Division of Radioprotective Drug Development Research, Institute of Nuclear Medicine and Allied Sciences, Delhi 110054 (India); Singh, Bhawna [Department of Radiation Genetics and Epigenetics, Division of Radioprotective Drug Development Research, Institute of Nuclear Medicine and Allied Sciences, Delhi 110054 (India); Singh, Anju; Kukreti, Shrikant [Nucleic Acid Research Laboratory, Department of Chemistry, University of Delhi, Delhi 11007 (India)

2016-06-10

Highlights: • ITC study showed binding of ethyl pyruvate with BSA with high binding affinity. • Ethyl pyruvate binding caused conformation alteration of BSA. • Fluorescence quenching mechanism is static in nature. • Electrostatic, hydrogen bonding and hydrophobic forces involved in binding. • Docking confirmed role of electrostatic, hydrogen bonding and hydrophobic forces. - Abstract: Various in vitro and in vivo studies have shown the anti-inflammatory and anticancer potential role of ethyl pyruvate. Bio-distribution of drugs is significantly influenced by the drug-serum protein binding. Therefore, the binding mechanism of the ethyl pyruvate with bovine serum albumin was investigated using UV–vis absorption, fluorescence, circular dichroism, isothermal titration calorimetry and molecular docking techniques. Absorption and fluorescence quenching studies indicated the binding of ethyl pyruvate with protein. Circular dichroism spectra of bovine serum albumin confirmed significant change in the conformation of protein upon binding. Thermodynamic data confirmed that ethyl pyruvate binds to bovine serum albumin at the two different sites with high affinity. Binding of ethyl pyruvate to bovine serum albumin involves hydrogen bonding, van der Waal and hydrophobic interactions. Further, docking studies indicated that ethyl pyruvate could bind significantly at the three binding sites. The results will definitely contribute to the development of ethyl pyruvate as drug.

Nanoscale fabrication and characterization of chemically modified silicon surfaces using conductive atomic force microscopy in liquids

Science.gov (United States)

Kinser, Christopher Reagan

This dissertation examines the modification and characterization of hydrogen-terminated silicon surfaces in organic liquids. Conductive atomic force microscope (cAFM) lithography is used to fabricate structures with sub-100 nm line width on H:Si(111) in n-alkanes, 1-alkenes, and 1-alkanes. Nanopatterning is accomplished by applying a positive (n-alkanes and 1-alkenes) or a negative (1-alkanes) voltage pulse to the silicon substrate with the cAFM tip connected to ground. The chemical and kinetic behavior of the patterned features is characterized using AFM, lateral force microscopy, time-of-flight secondary ion mass spectroscopy (TOF SIMS), and chemical etching. Features patterned in hexadecane, 1-octadecene, and undecylenic acid methyl ester exhibited chemical and kinetic behavior consistent with AFM field induced oxidation. The oxide features are formed due to capillary condensation of a water meniscus at the AFM tip-sample junction. A space-charge limited growth model is proposed to explain the observed growth kinetics. Surface modifications produced in the presence of neat 1-dodecyne and 1-octadecyne exhibited a reduced lateral force compared to the background H:Si(111) substrate and were resistant to a hydrofluoric acid etch, characteristics which indicate that the patterned features are not due to field induced oxidation and which are consistent with the presence of the methyl-terminated 1-alkyne bound directly to the silicon surface through silicon-carbon bonds. In addition to the cAFM patterned surfaces, full monolayers of undecylenic acid methyl ester (SAM-1) and undec-10-enoic acid 2-bromoethyl ester (SAM-2) were grown on H:Si(111) substrates using ultraviolet light. The structure and chemistry of the monolayers were characterized using AFM, TOF SIMS, X-ray photoelectron spectroscopy (XPS), X-ray reflectivity (XRR), X-ray standing waves (XSW), and X-ray fluorescence (XRF). These combined analyses provide evidence that SAM-1 and SAM-2 form dense monolayers

In vivo pharmacological characterization of (+/-)-4-[2-(1-methyl-2-pyrrolidinyl)ethyl]thiophenol hydrochloride (SIB-1553A), a novel cholinergic ligand: microdialysis studies.

Science.gov (United States)

Rao, Tadimeti S; Reid, Richard T; Correa, Lucia D; Santori, Emily M; Gardner, Michael F; Sacaan, Aida I; Lorrain, Daniel; Vernier, Jean-Michel

2003-10-03

SIB-1553A ((+/-)-4-[2-(1-methyl-2-pyrrolidinyl)ethyl]thiophenol HCl) is a neuronal nicotinic acetylcholine receptor (nAChR) ligand which is active in rodent and primate models of cognition. In functional assays, SIB-1553A exhibits marked subtype selectivity for nAChRs as compared to nicotine. In addition SIB-1553A also exhibits affinities to histaminergic (H3) and serotonergic (5-HT1 and 5HT2) receptors and sigma binding sites. In the present investigation, we characterized SIB-1553A-induced neurotransmitter release in vivo. Following subcutaneous injection (s.c., 10 mg/kg), SIB-1553A rapidly entered the brain achieving concentration of approximately 20 microM 15 min post-injection and was eliminated from plasma with a terminal half-life of approximately 32 min. In freely moving rats, SIB-1553A (1-40 mg/kg, s.c.), markedly increased ACh release in the hippocampus and prefrontal cortex. In both regions, the magnitude of SIB-1553A-induced ACh release was greater than that seen with the prototypical nAChR agonist, nicotine (0.4 mg/kg, s.c.). Both isomers of SIB-1553A induced similar levels of increase in hippocampal ACh release. Increased hippocampal ACh release was also observed following oral administration of SIB-1553A (40 mg/kg) or after local perfusion into the hippocampus (1 mM). SIB-1553A-induced hippocampal ACh release was significantly attenuated by two nAChR antagonists, mecamylamine (MEC) and dihydro-beta-erythroidine (DHbetaE), and by the dopamine (DA) (D1) antagonist, SCH-23390, arguing that ACh release, in part, involves activation of nAChRs and a permissive DA synapse. In contrast to its robust effects on ACh release, SIB-1553A (40 mg/kg, s.c.) modestly increased striatal DA release (approximately 180% of baseline). Due to the proposed role of cholinergic pathways in learning and memory, the neurochemical profile of SIB-1553A suggests a potential for it to treat cognitive dysfunction.

Molecular interactions in ethyl acetate-chlorobenzene binary solution: Dielectric, spectroscopic studies and quantum chemical calculations

Science.gov (United States)

Karthick, N. K.; Kumbharkhane, A. C.; Joshi, Y. S.; Mahendraprabu, A.; Shanmugam, R.; Elangovan, A.; Arivazhagan, G.

2017-05-01

Dielectric studies using Time Domain Reflectometry method has been carried out on the binary solution of Ethyl acetate (EA) with Chlorobenzene (CBZ) over the entire composition range. Spectroscopic (FTIR and 13C NMR) signatures of neat EA, CBZ and their equimolar binary solution have also been recorded. The results of the spectroscopic studies favour the presence of (CBZ) Csbnd H ⋯ Odbnd C (EA), (EA) methylene Csbnd H ⋯ π electrons (CBZ) and (EA) methyl Csbnd H ⋯ Cl (CBZ) contacts which have been validated using quantum chemical calculations. Dimerization of CBZ has been identified. Presence of β-clusters has been identified in all the solutions. Although EA and CBZ molecules have nearly equal molar volumes, CBZ molecules experience larger hindrance for the rotation than EA molecules. Very small excess dielectric constant (εE) values may be correlated with weak heteromolecular forces and/or closed heteromolecular association.

Behaviour of solid phase ethyl cyanide in simulated conditions of Titan

Science.gov (United States)

Couturier-Tamburelli, I.; Toumi, A.; Piétri, N.; Chiavassa, T.

2018-01-01

In order to simulate different altitudes in the atmosphere of Titan, we investigated using infrared spectrometry and mass spectrometry the photochemistry of ethyl cyanide (CH3CH2CN) ices at different temperatures. Heating experiments of the solid phase until complete desorption showed up three phase transitions with a first one appearing to be approximately at the temperature of Titan's surface (94 K), measured by the Huygens probe. Ethyl cyanide, whose presence has been suggested in solid phase in Titan, can be considered as another nitrile for photochemical models of the Titan atmosphere after our first study (Toumi et al., 2016) concerning vinyl cyanide (CH2CHCN). The desorption energy of ethyl cyanide has been calculated to be 36.75 ( ± 0.55) kJ mol-1 using IRTF and mass spectroscopical techniques. High energetic photolysis (λ > 120 nm) have been performed and we identified ethyl isocyanide, vinyl cyanide, cyanoacetylene, ethylene, acetylene, cyanhydric acid and a methylketenimine form as photoproducts from ethyl cyanide. The branching ratios of the primary products were determined at characteristic temperatures of Titan thanks to the value of the νCN stretching band strength of ethyl cyanide that has been calculated to be 4.12 × 10-18 cm molecule-1. We also report here for the first time the values of the photodissociation cross sections of C2H5CN for different temperatures.

Quantification of fatty acid ethyl esters (FAEE) and ethyl glucuronide (EtG) in meconium for detection of alcohol abuse during pregnancy: Correlation study between both biomarkers.

Science.gov (United States)

Cabarcos, Pamela; Tabernero, María Jesús; Otero, José Luís; Míguez, Martha; Bermejo, Ana María; Martello, Simona; De Giovanni, Nadia; Chiarotti, Marcello

2014-11-01

This article presents results from 47 meconium samples, which were analyzed for fatty acid ethyl esters (FAEE) and ethyl glucuronide (EtG) for detection of gestational alcohol consumption. A validated microwave assisted extraction (MAE) method in combination with GC-MS developed in the Institute of Forensic Science (Santiago de Compostela) was used for FAEE and the cumulative concentration of ethyl myristate, ethyl palmitate and ethyl stearate with a cut-off of 600ng/g was applied for interpretation. A simple method for identification and quantification of EtG has been evaluated by ultrasonication followed solid phase extraction (SPE). Successful validation parameters were obtained for both biochemical markers of alcohol intake. FAEE and EtG concentrations in meconium ranged between values lower than LOD and 32,892ng/g or 218ng/g respectively. We have analyzed FAEE and EtG in the same meconium aliquot, enabling comparison of the efficiency of gestational ethanol exposure detection. Certain agreement between the two biomarkers was found as they are both a very specific alcohol markers, making it a useful analysis for confirmation. Copyright © 2014 Elsevier B.V. All rights reserved.

Substoichiometric determination of selenium with potassium ethyl xanthate

International Nuclear Information System (INIS)

Chandrasekhar Reddy, P.; Polaiah, B.; Rangamannar, B.

1989-01-01

A substoichiometric radiochemical method was developed for the determination of selenium with potassium ethyl xanthate. The selenium ethyl xanthate complex formed was extracted into chloroform from borate buffer at pH 5. The effect of foreign ions on the extraction was studied. Microgram quantities of selenium could be conveniently determined with a fair degree of accuracy. The method was successfully applied for the determination of selenium content in food stuffs such as 'Jaggery' and 'Wheat powder'. (author) 4 refs.; 3 figs

Crystal structure of bis-[N-(2-hy-droxy-eth-yl)-N-methyl-dithio-carbamato-κ2S,S'](pyridine)-zinc(II) pyridine monosolvate and its N-ethyl analogue.

Science.gov (United States)

Poplaukhin, Pavel; Tiekink, Edward R T

2017-07-01

The common structural feature of the title compounds, [Zn(C 4 H 8 NOS 2 ) 2 (C 5 H 5 N)]·C 5 H 5 N (I) and [Zn(C 5 H 10 NOS 2 ) 2 (C 5 H 5 N)]·C 5 H 5 N (II), which differ by having di-thio-carbamate N-bound methyl (I) and ethyl (II) groups, is the coordination of each Zn II atom by two non-symmetrically chelating di-thio-carbamate ligands and by a pyridine ligand; in each case, the non-coordinating pyridine mol-ecule is connected to the Zn-containing mol-ecule via a (hy-droxy)O-H⋯N(pyridine) hydrogen bond. The resulting NS 4 coordination geometry is closer to a square-pyramid than a trigonal bipyramid in the case of (I), but almost inter-mediate between the two extremes in (II). The mol-ecular packing features (hy-droxy)O-H⋯O(hy-droxy) hydrogen bonds, leading to supra-molecular chains with a zigzag arrangement along [10-1] (I) or a helical arrangement along [010] (II). In (I), π-π [inter-centroid distances = 3.4738 (10) and 3.4848 (10) Å] between coordinating and non-coordinating pyridine mol-ecules lead to stacks comprising alternating rings along the a axis. In (II), weaker π-π contacts occur between centrosymmetrically related pairs of coordinating pyridine mol-ecules [inter-centroid separation = 3.9815 (14) Å]. Further inter-actions, including C-H⋯π(chelate) inter-actions in (I), lead to a three-dimensional architecture in each case.

Two cases of methyl alcohol intoxication by sub-chronic inhalation and dermal exposure during aluminum CNC cutting in a small-sized subcontracted factory.

Science.gov (United States)

Ryu, Jia; Lim, Key Hwan; Ryu, Dong-Ryeol; Lee, Hyang Woon; Yun, Ji Young; Kim, Seoung-Wook; Kim, Ji-Hoon; Jung-Choi, Kyunghee; Kim, Hyunjoo

2016-01-01

Methyl alcohol poisoning has been mainly reported in community. Two cases of methyl alcohol poisoning occurred in a small-sized subcontracted factory which manufactured smartphone parts in Korea. One young female patient presented with dyspnea and visual disturbance. Another young male patient presented with visual disturbance and myalgia. They treated with sodium bicarbonate infusion and hemodialysis for metabolic acidosis. In addition, he received ethyl alcohol per oral treatment. Her and his urinary methyl alcohol concentration was detected as 7.632 mg/L, 46.8 mg/L, respectively, although they were treated hemodialysis. Results of the working environment measurement showed that the concentration of methyl alcohol (1030.1-2220.5 ppm) in the air exceeded the time weighted average (200 ppm). They were diagnosed with optic neuropathy due to methyl alcohol poisoning and still have visual impairment. Workers who hired as dispatched employees in a small-sized subcontracted factory were exposed to high concentrations of methyl alcohol. The workplace had poor ventilation system. In addition, workers did not wear proper personal protect equipment. Working environment measurement and annual chekups for workers were not performed. They were in a blind spot to occupational safety and health. More attention is needed to protect vulnerable workers' health.

Synthesis, NMR spectral and antimicrobial studies of some [N-methyl-3t-alkyl-2r,6c-diarylpiperidin-4-ylidine]-5‧-methylthiazolidine-4-ones

Science.gov (United States)

Prakash, S. M.; Pandiarajan, K.; Kumar, S.

2013-06-01

Four new [N-methyl-3t-alkyl-2r,6c-diaryl-4-ylidine]-5'-methylthiozolidin-4-ones 9-12 have been synthesized by the condensation of N-methyl-3t-alkyl-2r,6c-diarylpiperidin-4-one thiosemicarbazones with ethyl 2-bromopropionate. These compounds have been characterized using FT-IR, 1H NMR, 13C NMR spectral techniques. HOMOCOSY, HSQC and HMBC spectral study have been done for [N-methyl-3,3-dimethyl-2r,6c-bis(p-methoxyphenyl)piperidin-4-ylidine]-5'-methylthiazolidine-4-one (12). Two geometrical isomers are formed in this reaction. In all these compounds piperidin rings adopt chair conformation. The rotation of the aryl group at C-2 is rather slow in 10-12. Antimicrobial activities have also been studied for 9-12. These compounds are active against all the tested bacterial and fungal strains.

Cyclohexenones Through Addition of Ethyl Acetoacetate to 3-Aryl-1 ...

African Journals Online (AJOL)

Chalcone derivatives 3a–i containing a thiophene ring were prepared by the condensation of 1-(thiophen-3-yl)ethanone with aromatic aldehydes in excellent yields. The Michael addition of ethyl acetoacetate 4 to chalcone derivatives 3a–i resulted in the formation of nine novel ethyl 6-aryl ...

Characterization of silicon-oxide interfaces and organic monolayers by IR-UV ellipsometry and FTIR spectroscopy

Science.gov (United States)

Hess, P.; Patzner, P.; Osipov, A. V.; Hu, Z. G.; Lingenfelser, D.; Prunici, P.; Schmohl, A.

2006-08-01

VUV-laser-induced oxidation of Si(111)-(1×1):H, Si(100):H, and a-Si:H at 157 nm (F II laser) in pure O II and pure H IIO atmospheres was studied between 30°C and 250°C. The oxidation process was monitored in real time by spectroscopic ellipsometry (NIR-UV) and FTIR spectroscopy. The ellipsometric measurements could be simulated with a three-layer model, providing detailed information on the variation of the suboxide interface with the nature of the silicon substrate surface. Besides the silicon-dioxide and suboxide layer, a dense, disordered, roughly monolayer thick silicon layer was included, as found previously by molecular dynamics calculations. The deviations from the classical Deal-Grove mechanism and the self-limited growth of the ultrathin dioxide layers (TMS) groups and n-alkylthiol monolayers on gold-coated silicon. The C-H stretching vibrations of the methylene and methyl groups could be identified by FTIR spectroscopy and IR ellipsometry.

Joint stress of chlorimuron-ethyl and cadmium on wheat Triticum aestivum at biochemical levels

International Nuclear Information System (INIS)

Wang, M.-E; Zhou, Q.-X.

2006-01-01

Biochemical responses to joint stress of chlorimuron-ethyl and cadmium (Cd) in wheat Triticum aestivum were examined. The joint action of chlorimuron-ethyl and Cd weakened the inhibition of Cd or chlorimuron-ethyl on the formation of chlorophyll. It was deduced that wheat plants had the capability to protect themselves by increasing the activity of the antioxidant enzyme peroxidase (POD) with the exposure time. The joint effect of chlorimuron-ethyl and Cd on the superoxide dismutase (SOD) activity in leaves was additive, while the joint effect on the SOD activity in roots was determined by the interaction of chlorimuron-ethyl and Cd in wheat. It was also concluded that the change of malondialdehyde (MDA) content in wheat might not be a good biomarker in the oxidative damage by chlorimuron-ethyl, while a decrease in the soluble protein content and POD activity in roots could be considered as a biomarker in the damage of wheat by chlorimuron-ethyl and Cd. - Soluble protein content and peroxidase activity in seedlings were the biomarkers indicating joint stress of chemicals

Photocatalytic degradation of paraoxon-ethyl in aqueous solution using titania nanoparticulate film

International Nuclear Information System (INIS)

Prasad, G.K.; Ramacharyulu, P.V.R.K.; Kumar, J. Praveen; Srivastava, A.R.; Singh, Beer

2012-01-01

Photocatalytic degradation of paraoxon-ethyl (o,o-diethyl o-(4-nitrophenyl) phosphate), a well known surrogate of chemical warfare agents, in aqueous solution was studied by using titania nanoparticulate film. Reaction followed pseudo first order behaviour. Photolytic degradation reaction of paraoxon-ethyl demonstrated relatively low rate with a value of rate constant of 2.5 × 10 −3 min −1 . Whereas, degradation reaction in the presence of titania nanoparticulate film and UV light displayed enhanced rate with a value of rate constant of 6.9 × 10 −3 min −1 due to photocatalysis. Gas chromatography–mass spectrometry analysis showed the formation of p-nitrophenol, o,o-diethyl phosphonic acid, o-ethyl, diphosphonic acid, phosphoric acid, dimerized product of o,o-diethyl phosphonic acid, acetaldehyde, and carbon dioxide due to photocatalytic degradation of paraoxon-ethyl. It indicates that, photocatalytic degradation reaction begins with destruction of P–O–C bonds. Subsequently, P, C atoms were found to be oxidized gradually, and contributed to its photocatalytic degradation. - Highlights: ► Synthesis of titania nanoparticles by sol–gel method. ► Fabrication of titania nanoparticulate film by dip coating. ► Paraoxon ethyl degradation reactions followed pseudo first order behaviour. ► Paraoxon-ethyl degraded to non toxic compounds like CO 2 , acetaldehyde, and nitrophenol.

Synthesis of iodine-123 labelled analogues of imidazenil and ethyl-imidazenil for studying benzodiazepine receptors using SPECT

International Nuclear Information System (INIS)

Katsifis, A.; Mattner, F.; Dikic, B.; Najdovski, L.; Kassiou, M.

1996-01-01

The [ 123 I]iodinated analogues of the benzodiazepine receptor partial agonist imidazenil and N-ethyl imidazenil have been synthesised for the study of the central benzodiazepine receptor using SPECT. [ 123 I]Iodomidazenil and [ 123 I]N-ethyliodoimidazenil were prepared by nucleophilic bromine-iodine exchange in acetic acid at 150 o . The products were purified by semi-preparative reverse-phase HPLC with average radiochemical yields of 80% in a total synthesis time of 80 minutes. The specific activity was determined to be greater than 2500 Ci/mmol. The radiochemical and chemical purity assessed by radio-TLC and HPLC were found to be 98%. Alternatively, iododestannylation reactions via the trimethyltin precursors with Na[ 123 I] in the presence of Chloramine-T or peracetic acid resulted in yields of only 20-25% with the bulk of activity being lost as volatile methyl [ 123 I]iodide. (author)

Syntheses of some Bunte's salts, isothiourea derivatives and thioethers, potential radioprotective agents. Part 40

International Nuclear Information System (INIS)

Tulecki, J.; Kalinowska Torz, J.; Musial, E.; Nacewicz-Anjedani, H.; Senczuk, L.; Skwarski, D.; Sobolewski, H.

1977-01-01

By reacting respective halogen-derivatives with sodium or potassium thiosulphate there were obtained sodium or potassium salts of S-thiosulphates of 1-ureidocarbonyl-1-butyl, 3,4-dihydroxyphenacyl, carbophenoxymethyl, 2-hydroxyphenacyl, /N-(4-iodophenyl) carbamyl/methyl, /N-(4-iodophenyl) carbamyl/ethyl, /N-(2-iodophenyl) carbamyl/-methyl, /N-(2-iodophenyl) carbamyl/ethyl, /N-(6-carbomethoxybenzothiazolyl-2)-carbamyl/methyl, (2,4-dihydroxy-6-methylpyrimidyl-5)-methyl and (2,4-dihydroxypyrimidyl-5)-methyl. Reactions of thiourea with respective halogen-derivatives yielded hydrochlorides of 1-methyl-02-amidinothiomethylbenzimidazole, 1-ethyl-2-amidinothiomethylbenzimidazole, S-/N-(2-iodophenyl) carbamylethyl/ isothiourea, 5-amidinothiomethyl-6-methyl-2,4-dihydroxypyrimide and 5-amidinothiomethyl-2,4-dihydroxypyrimidine. Reactions of 4-chloroquinoline N-oxide with respective mercaptanes afforded thioether derivatives of quinoline N-oxide: 4-(p-chlorophenylthio)-4-(t-butylthio)-, 4-(3-naphtylthio)-, 4-(3-naphtylaminoacetylthio), 4-(benzimidazolythio)-, 4-(benzothiazolylthio) - and 4-benzoxalylthio. (author)

Spectroscopic characterization of the ethyl radical-water complex.

Science.gov (United States)

Lin, Chen; Finney, Brian A; Laufer, Allan H; Anglada, Josep M; Francisco, Joseph S

2016-10-14

An ab initio investigation has been employed to determine the structural and spectroscopic parameters, such as rotational constants, vibrational frequencies, vertical excitation energies, and the stability of the ethyl-water complex. The ethyl-water complex has a binding energy of 1.15 kcal⋅mol -1 . The interaction takes place between the hydrogen of water and the unpaired electron of the radical. This interaction is found to produce a red shift in the OH stretching bands of water of ca. 84 cm -1 , and a shift of all UV absorption bands to higher energies.

Synthesis and Isolation of New Regioisomeric 4-Thiazolidinones and Their Anticonvulsant Activity

OpenAIRE

GÜRSOY, Aysel; TERZİOĞLU, Nalan

2005-01-01

Two regioisomer series, 2-(3-ethyl-4(3H)-quinazolinone-2- ylmercaptoacetylhydrazono)-3-alkyl/3-aryl-5-methyl-4-thiazolidinones (12-21) and 2-arylimino-3-(3-ethyl-4(3H)-quinazolinone-2-ylmercaptoacetylamino)- 5-methyl-4-thiazolidinones (22-26), were synthesized by the cyclization of 1-(3-ethyl-4(3H)-quinazolinone-2-ylmercaptoacetyl)-4-alkyl/aryl thiosemicarbazides (1-11) with ethyl 2-bromopropionate in the presence of anhydrous sodium acetate in anhydrous ethanolic medium. The structur...

In situ nanoscale refinement by highly controllable etching of the (111) silicon crystal plane and its influence on the enhanced electrical property of a silicon nanowire

International Nuclear Information System (INIS)

Gong Yibin; Dai Pengfei; Gao Anran; Li Tie; Zhou Ping; Wang Yuelin

2011-01-01

Nanoscale refinement on a (100) oriented silicon-on-insulator (SOI) wafer was introduced by using tetra-methyl-ammonium hydroxide (TMAH, 25 wt%) anisotropic silicon etchant, with temperature kept at 50 °C to achieve precise etching of the (111) crystal plane. Specifically for a silicon nanowire (SiNW) with oxide sidewall protection, the in situ TMAH process enabled effective size reduction in both lateral (2.3 nm/min) and vertical (1.7 nm/min) dimensions. A sub-50 nm SiNW with a length of microns with uniform triangular cross-section was achieved accordingly, yielding enhanced field effect transistor (FET) characteristics in comparison with its 100 nm-wide pre-refining counterpart, which demonstrated the feasibility of this highly controllable refinement process. Detailed examination revealed that the high surface quality of the (111) plane, as well as the bulk depletion property should be the causes of this electrical enhancement, which implies the great potential of the as-made cost-effective SiNW FET device in many fields. (semiconductor materials)

Hydrogenation of ethyl acetate on Re/γ-A12O3 catalyst

International Nuclear Information System (INIS)

Minachev, K.M.; Avaev, V.I.; Ryashentseva, M.A.

1986-01-01

This paper presents a study of the catalytic properties of 5% Re/gamma-A1 2 O 3 contact in the hydrogenation reaction of ethyl acetate (EA). To clarify the paths of formation of the by products, experiments were also carried out with ethanol under the conditions of hydrogenation of EA. It is shown that the main product of the hydrogenation of EA is ethanol. In addition, Et 2 O, water, and traces of acetaldehyde were found in the catalyzate. In the range of conditions studied, the maximal conversion of ethyl acetate into ethanol is 49%. Increase in the temperature and molar ratio, and also decrease in pressure leads to a decrease in the selectivity of hydrogenation of ethyl acetate into ethanol. Byproducts of the hydrogenation of ethyl acetate - diethyl ether and hydrocarbons - are formed not only as a result of dehydration of ethanol on gamma-A1 2 O 3 , but also directly from ethyl acetate (diethyl ether) and also by the hydrogenolysis of the C-O bond in ethanol on rhenium (hydrocarbons)

Extraction of hafnium by 1-phenyl-3-methyl-4-benzoyl-5-pyralozone from aqueous-alcoholic solutions

International Nuclear Information System (INIS)

Hala, J.; Prihoda, J.

1975-01-01

Extraction of hafnium by 1-phenyl-3-methyl-4-benzoyl-5-pyrazolone (HL) in benzene, toluene, chloroform and tetrachloromethane from aqueous-alcoholic solutions of the formal acidity of 2M-HClO 4 was studied. Methyl, ethyl, n- and isopropyl, tert-butyl and allyl alcohol as well as ethylene glycol monomethyl ether and propylene glycol were used as organic components of the mixed aqueous-organic phase. Their presence in some cases resulted in a synergic increase in the distribution ratio of hafnium. The increase is interpreted using the results of a slope analysis and measurements of the alcohol distribution and the relative permittivity of the organic phase. It is suggested that HfL 4 molecules were solvated by alcohol molecules in the organic phase. At high alcohol concentration synergism changed into antagonism. This was caused by changes in the distribution of HL and its interaction with the alcohol in the organic phase. (author)

Photocatalytic degradation of paraoxon-ethyl in aqueous solution using titania nanoparticulate film

Energy Technology Data Exchange (ETDEWEB)

Prasad, G.K., E-mail: gkprasad2001@yahoo.com; Ramacharyulu, P.V.R.K.; Kumar, J. Praveen; Srivastava, A.R.; Singh, Beer

2012-06-30

Photocatalytic degradation of paraoxon-ethyl (o,o-diethyl o-(4-nitrophenyl) phosphate), a well known surrogate of chemical warfare agents, in aqueous solution was studied by using titania nanoparticulate film. Reaction followed pseudo first order behaviour. Photolytic degradation reaction of paraoxon-ethyl demonstrated relatively low rate with a value of rate constant of 2.5 Multiplication-Sign 10{sup -3} min{sup -1}. Whereas, degradation reaction in the presence of titania nanoparticulate film and UV light displayed enhanced rate with a value of rate constant of 6.9 Multiplication-Sign 10{sup -3} min{sup -1} due to photocatalysis. Gas chromatography-mass spectrometry analysis showed the formation of p-nitrophenol, o,o-diethyl phosphonic acid, o-ethyl, diphosphonic acid, phosphoric acid, dimerized product of o,o-diethyl phosphonic acid, acetaldehyde, and carbon dioxide due to photocatalytic degradation of paraoxon-ethyl. It indicates that, photocatalytic degradation reaction begins with destruction of P-O-C bonds. Subsequently, P, C atoms were found to be oxidized gradually, and contributed to its photocatalytic degradation. - Highlights: Black-Right-Pointing-Pointer Synthesis of titania nanoparticles by sol-gel method. Black-Right-Pointing-Pointer Fabrication of titania nanoparticulate film by dip coating. Black-Right-Pointing-Pointer Paraoxon ethyl degradation reactions followed pseudo first order behaviour. Black-Right-Pointing-Pointer Paraoxon-ethyl degraded to non toxic compounds like CO{sub 2}, acetaldehyde, and nitrophenol.

Sensory reception of the primer pheromone ethyl oleate

Science.gov (United States)

Muenz, Thomas S.; Maisonnasse, Alban; Plettner, Erika; Le Conte, Yves; Rössler, Wolfgang

2012-05-01

Social work force distribution in honeybee colonies critically depends on subtle adjustments of an age-related polyethism. Pheromones play a crucial role in adjusting physiological and behavioral maturation of nurse bees to foragers. In addition to primer effects of brood pheromone and queen mandibular pheromone—both were shown to influence onset of foraging—direct worker-worker interactions influence adult behavioral maturation. These interactions were narrowed down to the primer pheromone ethyl oleate, which is present at high concentrations in foragers, almost absent in young bees and was shown to delay the onset of foraging. Based on chemical analyses, physiological recordings from the antenna (electroantennograms) and the antennal lobe (calcium imaging), and behavioral assays (associative conditioning of the proboscis extension response), we present evidence that ethyl oleate is most abundant on the cuticle, received by olfactory receptors on the antenna, processed in glomeruli of the antennal lobe, and learned in olfactory centers of the brain. The results are highly suggestive that the primer pheromone ethyl oleate is transmitted and perceived between individuals via olfaction at close range.

Evaluation of poly(2-ethyl-2-oxazoline) containing copolymer networks of varied composition as sustained metoprolol tartrate delivery systems.

Science.gov (United States)

Kostova, Bistra; Ivanova, Sijka; Balashev, Konstantin; Rachev, Dimitar; Christova, Darinka

2014-08-01

Segmented copolymer networks (SCN) based on poly(2-ethyl-2-oxazoline) and containing 2-hydroxyethyl methacrylate, 2-hydroxypropyl acrylate, and/or methyl methacrylate segments have been evaluated as potential sustained release systems of the water soluble cardioselective β-blocker metoprolol tartrate. The structure and properties of the drug carriers were investigated by differential scanning calorimetry, attenuated total reflectance Fourier transform infrared spectroscopy, scanning electron microscopy, and atomic force microscopy. Swelling kinetics of SCNs in various media was followed, and the conditions for effective MT loading were specified. MT-loaded SCNs with drug content up to 80 wt.% were produced. The release kinetics of metoprolol tartrate from the systems was studied and it was shown that the conetworks of different structure and composition are able to sustain the metoprolol tartrate release without additional excipients.

Hydrogen Production via Steam Reforming of Ethyl Alcohol over Palladium/Indium Oxide Catalyst

Directory of Open Access Journals (Sweden)

Tetsuo Umegaki

2009-01-01

Full Text Available We report the synergetic effect between palladium and indium oxide on hydrogen production in the steam reforming reaction of ethyl alcohol. The palladium/indium oxide catalyst shows higher hydrogen production rate than indium oxide and palladium. Palladium/indium oxide affords ketonization of ethyl alcohol with negligible by-product carbon monoxide, while indium oxide mainly affords dehydration of ethyl alcohol, and palladium affords decomposition of ethyl alcohol with large amount of by-product carbon monoxide. The catalytic feature of palladium/indium oxide can be ascribed to the formation of palladium-indium intermetallic component during the reaction as confirmed by X-ray diffraction and X-ray photoelectron spectroscopic measurements.

Characterization of [8-ethyl]-chlorophyll c3 from Emiliania huxleyi.

Science.gov (United States)

Álvarez, Susana; Zapata, Manuel; Garrido, José L; Vaz, Belén

2012-06-04

We report herein the isolation and complete characterization of a member of the chlorophyll c family, designated as [8-ethyl]-chlorophyll c(3) ([8-ethyl]-chl c(3)). Structural elucidation of this pigment rested on the analysis of mono- and bidimensional NMR, UV-VIS spectroscopy and ESI-MS data, and the configuration at the 13(2) position on chiral HPLC analysis.

Experimental spectroscopic (FTIR, FT-Raman, FT-NMR, UV-Visible) and DFT studies of 1-ethyl-1,4-dihydro-7-methyl-4oxo-1,8 napthyridine-3-carboxylic acids.

Science.gov (United States)

Muthu, S; Elamurugu Porchelvi, E

2013-12-01

The solid phase FTIR and FT-Raman spectra of 1-ethyl-1,4-dihydro-7-methyl-4oxo-1,8 napthyridine-3-carboxylic acid (EDMONCA) have been recorded in the regions 4000-500 and 4000-400 cm(-1) respectively. The equilibrium geometry, harmonic vibrational frequencies have been investigated by DFT/B3LYP and B3PW91 methods with 6-311G (d,p) basis set. The different between the observed and scaled wave number values of most of the fundamental is very small. The assignments of the vibrational spectra have been carried out with the aid of normal coordinate analysis (NCA) following the scaled quantum mechanical force field methodology (SQMFFM). Stability of the molecule arising from hyper conjugative interactions, charge delocalization has been analyzed using natural bond orbital (NBO) analysis. UV-Visible spectrum of the compound was recorded and the electronic properties HOMO and LOMO energies were measured. The electric dipole moment (μD) and first hyperpolarizability (βtot) values of the investigated molecule were computed using ab initio quantum mechanical calculations. The calculated results also show that the EDMONCA molecule may have microscopic nonlinear optics (NLO) behavior with non-zero values. (1)H and (13)C NMR spectra were recorded and (1)H and (13)C nuclear magnetic resonance chemical shift of the molecule were calculated using the gauge independent atomic orbital (GIAO) method. Thermal stability of EDMONCA was studied by thermogravimetric analysis (TGA). Next Fukui function was calculated to explain the chemical selectivity or reactivity site in EDMONCA. Finally molecular electrostatic potential (MEP) and other molecular properties were performed. Copyright © 2013 Elsevier B.V. All rights reserved.

A rapid approach to prepare poly(2-methyl-2-oxazoline)-based antifouling coating by UV irradiation

Science.gov (United States)

Zhu, Haikun; Mumtaz, Fatima; Zhang, Chong; Tan, Lin; Liu, Songtao; Zhang, Yalin; Pan, Chao; Wang, Yanmei

2017-12-01

A series of brush copolymers, poly[(2-methyl-2-oxazoline)-random-4-vinylpyridine] (PMOXA-r-4VP), with a variety of compositions was synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization of the poly(2-methyl-2-oxazoline) methacrylate macromonomer (PMOXA-MA) and 4-vinylpyridine (4VP), and then characterized by 1H NMR spectroscopy and gel permeation chromatography (GPC). The PMOXA-based coatings on the surfaces of glass, silicon, gold and polydimethylsiloxane (PDMS) substrates were then produced by short-time ultraviolet (UV) irradiation of PMOXA-r-4VP. Water contact angel (WCA), ellipsometry, X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and ζ-potential techniques were used to characterize the coatings. The results showed that copolymers can be successfully bonded on the surfaces of glass, silicon, gold, and PDMS substrate. Besides, the PMOXA-based coatings displayed a superior resistance to bovine serum albumin, human blood platelets, Human Umbilical Vein Endothelial Cells adsorption and good biocompatibility. Finally, stability test indicated that the stability of coatings can be improved with the content of the 4VP segment. Furthermore, PMOXA-r1/2-4VP immobilized surfaces displayed good antifouling property in long-term applications.

γ-Diimine palladium(II based complexes mediated polymerization of methyl methacrylate

Directory of Open Access Journals (Sweden)

Mahmoud Sunjuk

2017-02-01

Full Text Available The synthesis of new palladium(II complexes of the type [Pd(A–NC–ph–CN–ACl2] (4a–e (A = cyclohexyl (a, 2-isoprpropyl (b, pyrenyl (c, naphthyl (d, and 2,6-diisopropyl (e is described. The isolated γ-diimine ligands and their corresponding palladium(II complexes were characterized by their physical properties, elemental analysis, 1H NMR-, 13C NMR, and infrared spectroscopy. The palladium(II complexes (4a–e were employed successfully as catalysts for atom transfer radical polymerization (ATRP of methyl methacrylate (MMA in the presence of ethyl-2-bromoisobutyrate (EBIB as initiator at 90 °C. Polymerization with these catalyst systems afforded polymers with low molecular weight distribution (Mw/Mn and syndio-rich atactic poly (MMA with relatively higher [rr] diads.

Silicone Wristband Passive Samplers Yield Highly Individualized Pesticide Residue Exposure Profiles.

Science.gov (United States)

Aerts, Raf; Joly, Laure; Szternfeld, Philippe; Tsilikas, Khariklia; De Cremer, Koen; Castelain, Philippe; Aerts, Jean-Marie; Van Orshoven, Jos; Somers, Ben; Hendrickx, Marijke; Andjelkovic, Mirjana; Van Nieuwenhuyse, An

2018-01-02

Monitoring human exposure to pesticides and pesticide residues (PRs) remains crucial for informing public health policies, despite strict regulation of plant protection product and biocide use. We used 72 low-cost silicone wristbands as noninvasive passive samplers to assess cumulative 5-day exposure of 30 individuals to polar PRs. Ethyl acetate extraction and LC-MS/MS analysis were used for the identification of PRs. Thirty-one PRs were detected of which 15 PRs (48%) were detected only in worn wristbands, not in environmental controls. The PRs included 16 fungicides (52%), 8 insecticides (26%), 2 herbicides (6%), 3 pesticide derivatives (10%), 1 insect repellent (3%), and 1 pesticide synergist (3%). Five detected pesticides were not approved for plant protection use in the EU. Smoking and dietary habits that favor vegetable consumption were associated with higher numbers and higher cumulative concentrations of PRs in wristbands. Wristbands featured unique PR combinations. Our results suggest both environment and diet contributed to PR exposure in our study group. Silicone wristbands could serve as sensitive passive samplers to screen population-wide cumulative dietary and environmental exposure to authorized, unauthorized and banned pesticides.

Poly(methyl methacrylate) films for organic vapour sensing

CERN Document Server

Capan, R; Hassan, A K; Tanrisever, T

2003-01-01

Optical constants and fabrication parameters are investigated using surface plasmon resonance (SPR) studies on spun films of poly(methyl methacrylate) (PMMA) derivatives in contact with two different dielectric media. A value of 1.503 for the refractive index of PMMA films produced from a solution having concentration of 1 mg ml sup - sup 1 at the speed of 3000 rpm is in close agreement with the data obtained from ellipsometric measurements. The film thickness shows a power-law dependence on the spin speed but the thickness increases almost linearly with the concentration of the spreading solution. These results are in good agreement with the hydrodynamic theory for a low-viscosity and highly volatile liquid. On the basis of SPR measurements under dynamic conditions, room temperature response of PMMA films to benzene vapours is found to be fast, highly sensitive and reversible. The sensitivity of detection of toluene, ethyl benzene and m-xylene is much smaller than that of benzene.

In vitro pharmacological characterization of (+/-)-4-[2-(1-methyl-2-pyrrolidinyl)ethyl]thio]phenol hydrochloride (SIB-1553A), a nicotinic acetylcholine receptor ligand.

Science.gov (United States)

Rao, Tadimeti S; Adams, Pamala B; Correa, Lucia D; Santori, Emily M; Sacaan, Aida I; Reid, Richard T; Suto, Carla M; Vernier, Jean Michel

2003-08-15

SIB-1553A ((+/-)-4-[2-(1-methyl-2-pyrrolidinyl)ethyl]thio]phenol HCl) is a neuronal nicotinic acetylcholine receptor (nAChR) ligand which displaced the binding of [3H]nicotine (NIC) to the rat brain nAChRs with an IC(50) value of 110 nM with no appreciable affinity to the alpha7 nAhRs. SIB-1553A showed modest affinity for histaminergic (H3) and serotonergic (5-HT1 and 5-HT2) receptors, and sigma binding sites. In calcium flux assays, SIB-1553A (0.1-5 microM), in contrast to nicotine, showed a greater selectivity for beta4-subunit containing recombinant hnAChRs (alpha2beta4, alpha3beta4 and alpha4beta4) vs. beta2-subunit containing nAChRs (alpha4beta2 and alpha3beta2) both in terms of efficacy and potency. While NIC (10-30 microM) and epibatidine (0.01-0.1 microM) fully activated human muscle-type AChRs expressed by RD cell line, SIB-1553A was virtually ineffective for up to >100 microM and elicited less than 10% of the response due to suberyldicholine. SIB-1553A (< or =30 microM) evoked [3H]DA release from striatum, olfactory tubercles and prefrontal cortex (PFC), and [3H]NE release from hippocampus and PFC, and this evoked release was sensitive to mecamylamine (MEC). SIB-1553A-evoked neurotransmitter release exhibited region- and transmitter-specific antagonism by dehydro-beta-erythroidine (DHbetaE). SIB-1553A was less efficacious than NIC at evoking [3H]NE from the rat hippocampus and antagonized NIC response upon co-application implying partial agonist properties. SIB-1553A did not evoke basal [3H]ACh release from the rat striatum or hippocampus, but attenuated NMDA-evoked [3H]ACh release from the rat striatum. SIB-1553A did not inhibit rat brain cholinesterase for up to 1 mM. Multiple receptor affinities and release of several neurotransmitters may underlie the cognitive-enhancing effects of SIB-1553A documented in rodent and primate models.

X-ray structural studies and physicochemical characterization of (E)-6-(3,4-dimethoxyphenyl)-1-ethyl-4-mesitylimino-3-methyl- 3,4-dihydro-2(1H)-pyrimidinone polymorphs.

Science.gov (United States)

Miyamae, A; Kitamura, S; Tada, T; Koda, S; Yasuda, T

1991-10-01

The polymorphism of (E)-6-(3,4-dimethoxyphenyl)-1-ethyl-4-mesitylimino-3-methyl-3,4-di hydro- 2(1 H)-pyrimidinone (FK664; 1) was characterized by using X-ray powder diffractometry, differential scanning calorimetry (DSC), and IR spectroscopy. Structures of two polymorphs (Forms A and B) were determined by X-ray crystallographic analysis. Form A crystallized in the monoclinic space group P2(1)/c, with a = 13.504(2), b = 6.733(1), c = 24.910(8) A, beta = 96.55(4) degrees, z = 4, and dcal = 1.203 g/cm3, while Form B crystallized in the same space group, with a = 8.067(2), b = 15.128(4), c = 18.657(4) A, beta = 102.34(3) degrees, z = 4, and dcal = 1.216 g/cm3. The conformational features of 1 were very similar between the two polymorphs. Compound 1, in both crystal forms, took an energetically reasonable conformation in three rigid planes, such as 2-pyrimidone, trimethylphenyl, and dimethoxyphenyl rings, but the molecules were packed in different ways between the two polymorphs. In the Form B crystal, a short contact was possible, to form pi-pi interactions between two dimethoxyphenyl groups related with the inversion center in the crystal lattice; this interaction seems to contribute to stabilizing the crystal structure of Form B. Both Forms A and B showed only one endothermic peak due to fusion at 115 and 140 degrees C, respectively, on the DSC thermograms; therefore, it is suggested that there are no transition points between the two polymorphs. The heats of fusion obtained from the DSC thermograms were 33.2(2) kJ/mol for Form A and 36.8(1) kJ/mol for Form B.(ABSTRACT TRUNCATED AT 250 WORDS)

Determination of fatty acid ethyl esters (FAEE) and ethyl glucuronide (EtG) in hair: a promising way for retrospective detection of alcohol abuse during pregnancy?

Science.gov (United States)

Pragst, Fritz; Yegles, Michel

2008-04-01

The retrospective detection of alcohol consumption during pregnancy is an important part of the diagnosis of the fetal alcohol syndrome. A promising way to solve this problem can be the determination of fatty acid ethyl esters (FAEE) or/and ethyl glucuronide (EtG) in hair of the mothers. In this article, the present state in analytical determination and interpretation of FAEE and EtG concentrations in hair are reviewed. Both FAEE and EtG are minor metabolites of ethanol and as direct alcohol markers very specific for alcohol. They are durably deposited in hair, which enables taking advantage of the long diagnostic time window of this sample material. In the last years, specific and sensitive methods for determination of both alcohol markers in hair were developed. Headspace solid phase microextraction in combination with gas chromatography-mass spectroscopy after hair extraction with an n-heptane/dimethylsulfoxide mixture proved to be a favorable technique for determination of four characteristic FAEE (ethyl myristate, ethyl palmitate, ethyl oleate, and ethyl stearate). EtG is extracted from hair by water and analyzed either by gas chromatography-mass spectroscopy with negative chemical ionization after cleanup with solid phase extraction and derivatization with pentafluoropropionic anhydride or by liquid chromatography-mass spectroscopy-mass spectroscopy. The detection limits of the single FAEE as well as of EtG are in the range of 1 to 10 pg/mg. FAEE as well as EtG were determined in a larger number of hair samples of teetotalers, social drinkers, patients in alcohol withdrawal treatment, and death cases with previous known heavy drinking. From the results, the following criteria were derived: strict abstinence is excluded or improbable at C FAEE >0.2 ng/mg or C EtG >7 pg/mg. Moderate social drinkers should have C FAEE alcohol abuse is probable. Until now, there has been no evaluation in context of FAS diagnosis; however, a successful application for this purpose

Horseradish peroxidase-modified porous silicon for phenol monitoring

Energy Technology Data Exchange (ETDEWEB)

Kermad, A., E-mail: amina_energetique@yahoo.fr [Unité de Recherche Matériaux et Energies Renouvelables (URMER), Département de Physique, Faculté des Sciences, Université Abou Baker Belkaid, B.P. 119, Tlemcen 13000 (Algeria); Sam, S., E-mail: Sabrina.sam@polytechnique.edu [Centre de Recherche en Technologie des Semi-conducteurs pour l’Energétique (CRTSE), 02 Bd. Frantz-Fanon, B.P. 140, Alger-7 merveilles, Algiers (Algeria); Ghellai, N., E-mail: na_ghellai@yahoo.fr [Unité de Recherche Matériaux et Energies Renouvelables (URMER), Département de Physique, Faculté des Sciences, Université Abou Baker Belkaid, B.P. 119, Tlemcen 13000 (Algeria); Khaldi, K., E-mail: Khadidjaphy@yahoo.fr [Unité de Recherche Matériaux et Energies Renouvelables (URMER), Département de Physique, Faculté des Sciences, Université Abou Baker Belkaid, B.P. 119, Tlemcen 13000 (Algeria); Gabouze, N., E-mail: ngabouze@yahoo.fr [Centre de Recherche en Technologie des Semi-conducteurs pour l’Energétique (CRTSE), 02 Bd. Frantz-Fanon, B.P. 140, Alger-7 merveilles, Algiers (Algeria)

2013-11-01

Highlights: • Horseradish peroxidase enzyme (HRP) was covalently immobilized on porous silicon (PSi) surface. • Multistep strategy was used allowing the maintaining of the enzymatic activity of the immobilized enzyme. • Direct electron transfer has occurred between the immobilized enzyme and the surface. • Electrochemical measurements showed a response of HRP-modified PSi toward phenol in the presence of H{sub 2}O{sub 2}. -- Abstract: In this study, horseradish peroxidase enzyme (HRP) was covalently immobilized on porous silicon (PSi) surface using multistep strategy. First, acid terminations were generated on hydrogenated PSi surface by thermal hydrosilylation of undecylenic acid. Then, the carboxyl-terminated monolayer was transformed to active ester (succinimidyl ester) using N-hydroxysuccinimide (NHS) in the presence of the coupling agent N-ethyl-N′-(3-dimethylaminopropyl) carbodiimide (EDC). Subsequently, the enzyme was anchored on the surface via an amidation reaction. The structure of the PSi layers was observed by scanning electron microscopy (SEM). Infrared spectroscopy (FTIR) and contact angle measurements confirmed the efficiency of the modification at each step of the functionalization. Cyclic voltammetry was recorded using the HRP-modified PSi as working electrode. The results show that the enzymatic activity of the immobilized HRP is preserved and in the presence of hydrogen peroxide, the enzyme oxidizes phenolic molecules which were subsequently reduced at the modified-PSi electrode.

Horseradish peroxidase-modified porous silicon for phenol monitoring

International Nuclear Information System (INIS)

Kermad, A.; Sam, S.; Ghellai, N.; Khaldi, K.; Gabouze, N.

2013-01-01

Highlights: • Horseradish peroxidase enzyme (HRP) was covalently immobilized on porous silicon (PSi) surface. • Multistep strategy was used allowing the maintaining of the enzymatic activity of the immobilized enzyme. • Direct electron transfer has occurred between the immobilized enzyme and the surface. • Electrochemical measurements showed a response of HRP-modified PSi toward phenol in the presence of H 2 O 2 . -- Abstract: In this study, horseradish peroxidase enzyme (HRP) was covalently immobilized on porous silicon (PSi) surface using multistep strategy. First, acid terminations were generated on hydrogenated PSi surface by thermal hydrosilylation of undecylenic acid. Then, the carboxyl-terminated monolayer was transformed to active ester (succinimidyl ester) using N-hydroxysuccinimide (NHS) in the presence of the coupling agent N-ethyl-N′-(3-dimethylaminopropyl) carbodiimide (EDC). Subsequently, the enzyme was anchored on the surface via an amidation reaction. The structure of the PSi layers was observed by scanning electron microscopy (SEM). Infrared spectroscopy (FTIR) and contact angle measurements confirmed the efficiency of the modification at each step of the functionalization. Cyclic voltammetry was recorded using the HRP-modified PSi as working electrode. The results show that the enzymatic activity of the immobilized HRP is preserved and in the presence of hydrogen peroxide, the enzyme oxidizes phenolic molecules which were subsequently reduced at the modified-PSi electrode

Comparative toxicity of tetra ethyl lead and lead oxide to earthworms, Eisenia fetida (Savigny)

International Nuclear Information System (INIS)

Venkateswara Rao, J.; Kavitha, P.; Padmanabha Rao, A.

2003-01-01

Leaded gasoline contains tetra ethyl lead (TEL) as an antiknocking agent, which produces major amounts of lead oxide in automobile exhaust along with traces of TEL. To minimize the lead contamination, methyl tertiary butyl ether (MTBE) is used as a substitute for producing unleaded gasoline. It has become increasingly apparent that young children are highly susceptible to the harmful effects of lead. Hence, a study was carried out to monitor lead toxicity in soil, using adult earthworms (Eisenia fetida, Savigny). Leaded gasoline (TEL) and lead oxide are 383- and 211-fold more toxic than unleaded gasoline (MTBE) in 7 days of exposure and 627- and 290-fold more toxic in 14 days, respectively. Results indicate that the presence of TEL in leaded gasoline and lead oxide has a significant effect on behavior, morphology, and histopathology of earthworms. Absorption of TEL into the tissues is comparatively less than that of lead oxide but toxic effects were severe. Rupture of the cuticle, extrusion of coelomic fluid and inflexible metameric segmentation were observed, causing desensitization of the posterior region leading to fragmentation in earthworms

Identification of Differentially Methylated Sites with Weak Methylation Effects

Directory of Open Access Journals (Sweden)

Hong Tran

2018-02-01

Full Text Available Deoxyribonucleic acid (DNA methylation is an epigenetic alteration crucial for regulating stress responses. Identifying large-scale DNA methylation at single nucleotide resolution is made possible by whole genome bisulfite sequencing. An essential task following the generation of bisulfite sequencing data is to detect differentially methylated cytosines (DMCs among treatments. Most statistical methods for DMC detection do not consider the dependency of methylation patterns across the genome, thus possibly inflating type I error. Furthermore, small sample sizes and weak methylation effects among different phenotype categories make it difficult for these statistical methods to accurately detect DMCs. To address these issues, the wavelet-based functional mixed model (WFMM was introduced to detect DMCs. To further examine the performance of WFMM in detecting weak differential methylation events, we used both simulated and empirical data and compare WFMM performance to a popular DMC detection tool methylKit. Analyses of simulated data that replicated the effects of the herbicide glyphosate on DNA methylation in Arabidopsis thaliana show that WFMM results in higher sensitivity and specificity in detecting DMCs compared to methylKit, especially when the methylation differences among phenotype groups are small. Moreover, the performance of WFMM is robust with respect to small sample sizes, making it particularly attractive considering the current high costs of bisulfite sequencing. Analysis of empirical Arabidopsis thaliana data under varying glyphosate dosages, and the analysis of monozygotic (MZ twins who have different pain sensitivities—both datasets have weak methylation effects of <1%—show that WFMM can identify more relevant DMCs related to the phenotype of interest than methylKit. Differentially methylated regions (DMRs are genomic regions with different DNA methylation status across biological samples. DMRs and DMCs are essentially the same

Influence du bois sur certaines substances odorantes des vins

Directory of Open Access Journals (Sweden)

Jean-Noël Boidron

1998-12-01

The sensorial analysis of each substance demonstrates the negligible intervention in wine aroma of furfural, 5-methyl-furfural, and furfuryl alcohol, and the important participation of cis and trans β-methyl-γ-octalactone, vanilin 4-ethyl-phenol and 4-ethyl gaïacol.

Activity coefficients at infinite dilution measurements for organic solutes and water in the ionic liquid 1-ethyl-3-methylimidazolium tetracyanoborate

International Nuclear Information System (INIS)

Domanska, Urszula; Krolikowska, Marta; Acree, William E.; Baker, Gary A.

2011-01-01

Research highlights: → Measurements of activity coefficients at infinite dilution using GLC. → 36 organic solvents and water in the ionic liquid 1-ethyl-3-methylimidazolium tetracyanoborate, [EMIM][TCB]. → Possible entrainer for different separation processes. → The partial molar excess thermodynamic functions at infinite dilution were calculated. - Abstract: The activity coefficients at infinite dilution, γ 13 ∞ , for 36 solutes, including alkanes, cycloalkanes, alkenes, alkynes, aromatic hydrocarbons, alcohols, thiophene, tetrahydrofuran, ethers, acetone, and water, in the ionic liquid 1-ethyl-3-methylimidazolium tetracyanoborate, [EMIM][TCB], were determined by gas-liquid chromatography at temperatures from 298.15 K to 358.15 K. These values are compared to those previously published for selected solutes in the same ionic liquid. The values of the partial molar excess Gibbs free energy ΔG 1 E,∞ , enthalpy ΔH 1 E,∞ , and entropy ΔS 1 E,∞ at infinite dilution were calculated from the experimental γ 13 ∞ values obtained over the temperature range. Three gas-liquid partition coefficients, K L were calculated for all solutes and the Abraham solvation parameter model is discussed. The values of the selectivity for different separation problems were calculated from γ 13 ∞ and compared to literature values for N-methyl-2-pyrrolidinone (NMP), sulfolane, 1-decyl-3-methylimidazolium tetracyanoborate, [DMIM][TCB], and additional ionic liquids.

Photoluminescence and electrical properties of silicon oxide and silicon nitride superlattices containing silicon nanocrystals

International Nuclear Information System (INIS)

Shuleiko, D V; Ilin, A S

2016-01-01

Photoluminescence and electrical properties of superlattices with thin (1 to 5 nm) alternating silicon-rich silicon oxide or silicon-rich silicon nitride, and silicon oxide or silicon nitride layers containing silicon nanocrystals prepared by plasma-enhanced chemical vapor deposition with subsequent annealing were investigated. The entirely silicon oxide based superlattices demonstrated photoluminescence peak shift due to quantum confinement effect. Electrical measurements showed the hysteresis effect in the vicinity of zero voltage due to structural features of the superlattices from SiOa 93 /Si 3 N 4 and SiN 0 . 8 /Si 3 N 4 layers. The entirely silicon nitride based samples demonstrated resistive switching effect, comprising an abrupt conductivity change at about 5 to 6 V with current-voltage characteristic hysteresis. The samples also demonstrated efficient photoluminescence with maximum at ∼1.4 eV, due to exiton recombination in silicon nanocrystals. (paper)

Influence of prohexadione-calcium, trinexapac-ethyl and ...

African Journals Online (AJOL)

ethyl (TNE) and hexaconazole (HX) on lodging and gibberellin (GA) biosynthesis pathway of rice cultivar, Hwayeongbyeo. It was observed that these novel synthetic growth retardants suppressed lodging of rice under field conditions through ...

Identifying Key Proteins in Hg Methylation Pathways of Desulfovibrio by Global Proteomics, Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Summers, Anne O. [Univ. of Georgia, Athens, GA (United States). Dept. of Microbiology; Miller, Susan M. [Univ. of California, San Francisco, CA (United States). Dept. of Pharmaceutical Chemistry; Wall, Judy [Univ. of Missouri, Columbia, MO (United States). Dept. of Biochemistry; Lipton, Mary [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-06-18

Elemental mercury, Hg(0) is a contaminant at many DOE sites, especially at Oak Ridge National Laboratory (ORNL) where the spread of spilled Hg and its effects on microbial populations have been monitored for decades. To explore the microbial interactions with Hg, we have devised a global proteomic approach capable of directly detecting Hg-adducts of proteins. This technique developed in the facultative anaerobe, Escherichia coli, allows us to identify the proteins most vulnerable to acute exposure to organomercurials phenyl- and ethyl-mercury (as surrogates for the highly neurotoxic methyl-Hg) (Polacco, et al, 2011). We have found >300 such proteins in all metabolic functional groups and cellular compartments; most are highly conserved and can serve as markers for acute Hg exposure (Zink, et al. 2016, in preparation). We have also discovered that acute Hg exposure severely disrupts thiol, iron and redox homeostases, and electrolyte balance (LaVoie, et al., 2015) Thus, we proposed to bring these techniques to bear on the central problem of identifying the cellular proteins involved in bacterial uptake and methylation of mercury and its release from the cell.

Exploratory Report Parathion

NARCIS (Netherlands)

Hesse JM; Bont PHF; Slooff W; Booij H; CSR; ECO; LAE

1999-01-01

Dit document rapporteert gegevens over ethyl en methyl parathion betreffende bronnen, emissies, blootstellingsnivo's en risico's voor mens en ecosystemen. Op basis van beperkte gegevens is geconcludeerd dat de orale en inhalatoire risico's van ethyl en methyl parathion voor de

Optimization and validation of liquid chromatography and headspace-gas chromatography based methods for the quantitative determination of capsaicinoids, salicylic acid, glycol monosalicylate, methyl salicylate, ethyl salicylate, camphor and l-menthol in a topical formulation.

Science.gov (United States)

Pauwels, Jochen; D'Autry, Ward; Van den Bossche, Larissa; Dewever, Cédric; Forier, Michel; Vandenwaeyenberg, Stephanie; Wolfs, Kris; Hoogmartens, Jos; Van Schepdael, Ann; Adams, Erwin

2012-02-23

Capsaicinoids, salicylic acid, methyl and ethyl salicylate, glycol monosalicylate, camphor and l-menthol are widely used in topical formulations to relieve local pain. For each separate compound or simple mixtures, quantitative analysis methods are reported. However, for a mixture containing all above mentioned active compounds, no assay methods were found. Due to the differing physicochemical characteristics, two methods were developed and optimized simultaneously. The non-volatile capsaicinoids, salicylic acid and glycol monosalicylate were analyzed with liquid chromatography following liquid-liquid extraction, whereas the volatile compounds were analyzed with static headspace-gas chromatography. For the latter method, liquid paraffin was selected as compatible dilution solvent. The optimized methods were validated in terms of specificity, linearity, accuracy and precision in a range of 80% to 120% of the expected concentrations. For both methods, peaks were well separated without interference of other compounds. Linear relationships were demonstrated with R² values higher than 0.996 for all compounds. Accuracy was assessed by performing replicate recovery experiments with spiked blank samples. Mean recovery values were all between 98% and 102%. Precision was checked at three levels: system repeatability, method precision and intermediate precision. Both methods were found to be acceptably precise at all three levels. Finally, the method was successfully applied to the analysis of some real samples (cutaneous sticks). Copyright © 2011 Elsevier B.V. All rights reserved.

The synthesis of 5-[1-11C]ethyl barbiturates from labelled malonic esters

International Nuclear Information System (INIS)

Gee, A.; Laangstroem, B.

1991-01-01

The synthesis of [ 11 C]phenobarbital, [ 11 C]pentobarbital and[ 11 C]amobarbital labelled in the 5-[1- 11 C]ethyl position is reported. The malonic esters R- CH(CO 2 Et) 2 [R phenyl-, 1-methylbutyl-, and 3- methylbutyl- were alkylated with [1- 11 C]ethyl iodide prepared from [ 11 C]carbon dioxide. Ring closure of the 2-[1- 11 C]ethyl-labelled malonic esters with urea afforded 5-[1- 11 C]ethyl-phenobarbital,-phenobarbital, -pentobarbital and -amobarbital synthesis times of 42-47 min, counted from [ 11 C] carbon dioxide. In typical syntheses starting with 3 GBq pentobarbitol and (81 mCi) [ 11 C]carbon dioxide, 150-215 MBq (4-6 mCi) were produced in 25-30% decay corrected -amobarbital radiochemical yields with radiochemical purities greater than 98%. (author)

U.S. Geological Survey laboratory method for methyl tert-Butyl ether and other fuel oxygenates

Science.gov (United States)

Raese, Jon W.; Rose, Donna L.; Sandstrom, Mark W.

1995-01-01

Methyl tert-butyl ether (MTBE) was found in shallow ground-water samples in a study of 8 urban and 20 agricultural areas throughout the United States in 1993 and 1994 (Squillace and others, 1995, p. 1). The compound is added to gasoline either seasonally or year round in many parts of the United States to increase the octane level and to reduce carbon monoxide and ozone levels in the air. The U.S. Geological Survey (USGS) National Water Quality Laboratory (NWQL), near Denver, uses state-of-the-art technology to analyze samples for MTBE as part of the USGS water-quality studies. In addition, the NWQL offers custom analyses to determine two other fuel oxygenates--ethyl tert-butyl ether (ETBE) and tert-amyl methyl ether (TAME). The NWQL was not able to obtain a reference standard for tert-amyl ethyl ether (TAEE), another possible fuel oxygenate (Shelley and Fouhy, 1994, p. 63). The shallow ground-water samples were collected as part of the USGS National Water-Quality Assessment Program. These samples were collected from 211 urban wells or springs and 562 agricultural wells sampled by the USGS in 1993 and 1994. The wells were keyed to specific land-use areas to assess the effects of different uses on ground-water quality (Squillace and others, 1995, p. 2). Ground-water samples were preserved on site to pH less than or equal to 2 with a solution of 1:1 hydrochloric acid. All samples were analyzed at the NWQL within 2 weeks after collection. The purpose of this fact sheet is to explain briefly the analytical method implemented by the USGS for determining MTBE and other fuel oxygenates. The scope is necessarily limited to an overview of the analytical method (instrumentation, sample preparation, calibration and quantitation, identification, and preservation of samples) and method performance (reagent blanks, accuracy, and precision).

Whole-genome methylation caller designed for methyl- DNA ...

African Journals Online (AJOL)

etchie

2013-02-20

Feb 20, 2013 ... Our method uses a single-CpG-resolution, whole-genome methylation ... Key words: Methyl-DNA immunoprecipitation, next-generation sequencing, ...... methylation is prevalent in embryonic stem cells andmaybe mediated.

Efeitos do trinexapac-ethyl sobre o crescimento e florescimento da grama-batatais Effects of trinexapac-ethyl on the growth and flowering of the bahiagrass

Directory of Open Access Journals (Sweden)

F.C.L. Freitas

2002-12-01

Full Text Available O objetivo deste trabalho foi avaliar a eficiência de doses do trinexapac-ethyl, bem como dos intervalos de aplicação após o corte no crescimento vegetativo e florescimento da grama-batatais (Paspalum notatum, na redução de cortes e na melhoria da qualidade do gramado. O ensaio foi conduzido no campus da Universidade Federal de Viçosa, em Viçosa-MG, entre os meses de dezembro de 1998 e março de 1999, em gramado estabelecido. O delineamento experimental foi o de blocos ao acaso, com 13 tratamentos e quatro repetições, distribuídos em esquema fatorial (6 x 2 + 1, com seis doses de trinexapac-ethyl (0,00; 0,25; 0,50; 0,75; 1,00; e 1,25 kg ha-1, aplicadas aos dois e cinco dias após o corte do gramado, e uma testemunha com cortes a cada três semanas. Foram efetuadas avaliações a três, seis, nove e doze semanas após o corte, para produção de biomassa seca total, altura e número de inflorescências. Verificou-se, para todas as características avaliadas, relação direta entre o aumento da dose do regulador de crescimento trinexapac-ethyl e o período de controle do crescimento vegetativo e do florescimento, evitando-se, com isso, cortes no gramado pelo período de até 12 semanas com a aplicação de 0,75 kg ha-1. Não se constatou efeito da época de aplicação e também de doses do trinexapac-ethyl sobre a coloração do gramado.The objective of this work was to evaluate the efficiency of doses and application intervals of trinexapac-ethyl on the vegetative growth and flowering of bahiagrass, to reduce clips and improve lawn quality. The experiment was conducted on the campus of the Federal University of Viçosa, in Viçosa-MG - Brazil, from December 1998 to March 1999, in an established lawn. The experiment was arranged in a randomized complete block design, with 13 treatments and four repetitions, distributed in a factorial scheme (6 x 2 + 1, with six doses of trinexapac-ethyl (0.00; 0.25; 0.50; 0.75; 1.00 and 1.25 kg ha-1

21 CFR 184.1293 - Ethyl alcohol.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethyl alcohol. 184.1293 Section 184.1293 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) DIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...

Hydrocracking of ethyl laurate on bifunctional micro-/mesoporous composite materials

Energy Technology Data Exchange (ETDEWEB)

Adam, M.; Busse, O.; Reschetilowski, W. [Technische Univ. Dresden (Germany). Inst. for Industrial Chemistry

2011-07-01

Hydrocracking of ethyl laurate (dodecanoic acid ethyl ester) as a representative model compound of vegetable oil has been investigated in a fixed bed reactor under integral conditions. A synthesized micro-/mesoporous composite support material Al-MCM-41/ZSM-5 modified by different metal loadings (NiMo, NiW, PtNiW) was used as catalyst system. It could be demonstrated that the metal loading and reducibility influence product selectivity as well as deactivation behavior of catalyst samples. (orig.)

Synthesis of New Silicon-linked Lanthanocene Complexes and Their High Catalytic Activity for Methyl Methacrylate Polymerization with Nanometric Sodium Hydride as Co-catalyst

Institute of Scientific and Technical Information of China (English)

谢小敏; 黄吉玲

2005-01-01

The synthesis and characterization of four new silicon-linked lanthanocene complexes with pendant phenyl groups on cyclopentadiene were reported. Based on the data of elemental analyses, MS and IR, the complexes were presumed to be unsolvated and dimeric complexes [Me2Si(C5H3CMe2C6H5)2LnC1]2 [Ln=Er (1), Gd (2), Sm (3), Dy (4)]. In conjunction with AlEt3 or sodium hydride as the co-catalyst, these complexes could efficiently catalyze the polymerization of methyl methacrylate (MMA). When the nanometric sodium hydride was used as a co-catalyst, the complexes were highly effective for the polymerization of MMA. At low temperature and in short time, in [MeESi(C5H3CMe2C6H5)2LnC1]2/NaH (nanometric) system, the polymer was obtained in more than 80% yield and the molecular weight was greater than 105. The activity reached that of organolanthanide hydride as a single-component catalyst. In ]MeESi(C5H3CMe2C6H5)2ErC1]2/Nail (nanometric) system, the effects of the molar ratio of MMA/catalyst and catalyst/co-catalyst, and the temperature on polymerization were studied.

Determination of methyl mercury by aqueous phase Eehylation, followed by gas chromatographic separation with cold vapor atomic fluorescence detection

Science.gov (United States)

De Wild, John F.; Olsen, Mark L.; Olund, Shane D.

2002-01-01

A recent national sampling of streams in the United States revealed low methyl mercury concentrations in surface waters. The resulting median and mean concentrations, calculated from 104 samples, were 0.06 nanograms per liter (ng/L) and 0.15 ng/L, respectively. This level of methyl mercury in surface water in the United States has created a need for analytical techniques capable of detecting sub-nanogram per liter concentrations. In an attempt to create a U.S. Geological Survey approved method, the Wisconsin District Mercury Laboratory has adapted a distillation/ethylation/ gas-phase separation method with cold vapor atomic fluorescence spectroscopy detection for the determination of methyl mercury in filtered and unfiltered waters. This method is described in this report. Based on multiple analyses of surface water and ground-water samples, a method detection limit of 0.04 ng/L was established. Precision and accuracy were evaluated for the method using both spiked and unspiked ground-water and surface-water samples. The percent relative standard deviations ranged from 10.2 to 15.6 for all analyses at all concentrations. Average recoveries obtained for the spiked matrices ranged from 88.8 to 117 percent. The precision and accuracy ranges are within the acceptable method-performance limits. Considering the demonstrated detection limit, precision, and accuracy, the method is an effective means to quantify methyl mercury in waters at or below environmentally relevant concentrations

Molecular aggregation states of poly{2-(perfluorooctyl)ethyl acrylate} polymer brush thin film analyzed by grazing incidence X-ray diffraction

International Nuclear Information System (INIS)

Yamaguchi, H; Honda, K; Takahara, A; Kobayashi, M; Morita, M; Masunaga, H; Sasaki, S; Takata, M; Sakata, O

2009-01-01

Fluoropolymer brush with crystalline side chains was prepared by surface-initiated atom transfer radical polymerization of 2-(perfluorooctyl)ethyl acrylate (FA-C 8 ) from a flat silicon substrate. The crystallization and the molecular aggregation structures of polymer side chain at the outermost surface and internal region in the brush film were characterized by grazing incidence X-ray diffraction (GIXD) measurement using two different incident angles of X-ray. At the air interface of PFA-C 8 brush film, the rod-like R f group was oriented perpendicular to the surface forming a hexagonal packing structure to reduce surface energy. In contrast, the oriented R f groups parallel to the substrate coexisted at the internal region in the brush. This unique depth dependence of crystalline state of the fluoropolymer brush was observed by surface-sensitive GIXD measurement.

Identification of endometrial cancer methylation features using combined methylation analysis methods.

Directory of Open Access Journals (Sweden)

Michael P Trimarchi

Full Text Available DNA methylation is a stable epigenetic mark that is frequently altered in tumors. DNA methylation features are attractive biomarkers for disease states given the stability of DNA methylation in living cells and in biologic specimens typically available for analysis. Widespread accumulation of methylation in regulatory elements in some cancers (specifically the CpG island methylator phenotype, CIMP can play an important role in tumorigenesis. High resolution assessment of CIMP for the entire genome, however, remains cost prohibitive and requires quantities of DNA not available for many tissue samples of interest. Genome-wide scans of methylation have been undertaken for large numbers of tumors, and higher resolution analyses for a limited number of cancer specimens. Methods for analyzing such large datasets and integrating findings from different studies continue to evolve. An approach for comparison of findings from a genome-wide assessment of the methylated component of tumor DNA and more widely applied methylation scans was developed.Methylomes for 76 primary endometrial cancer and 12 normal endometrial samples were generated using methylated fragment capture and second generation sequencing, MethylCap-seq. Publically available Infinium HumanMethylation 450 data from The Cancer Genome Atlas (TCGA were compared to MethylCap-seq data.Analysis of methylation in promoter CpG islands (CGIs identified a subset of tumors with a methylator phenotype. We used a two-stage approach to develop a 13-region methylation signature associated with a "hypermethylator state." High level methylation for the 13-region methylation signatures was associated with mismatch repair deficiency, high mutation rate, and low somatic copy number alteration in the TCGA test set. In addition, the signature devised showed good agreement with previously described methylation clusters devised by TCGA.We identified a methylation signature for a "hypermethylator phenotype" in

Thermodynamic properties of 1-ethyl-4-nitro-1,2,3-triazole

Energy Technology Data Exchange (ETDEWEB)

Blokhin, Andrey V., E-mail: blokhin@bsu.by; Kohut, Sviataslau V.; Kabo, Gennady J.; Stepurko, Elena N.; Paulechka, Yauheni U.; Voitkevich, Olga V.

2013-08-10

Graphical abstract: - Highlights: • Heat capacities and phase transition enthalpies for 1-ethyl-4-nitro-1,2,3-triazole were measured. • Enthalpy of formation for 1-ethyl-4-nitro-1,2,3-triazole was determined. • Vapor pressure and enthalpy of sublimation of 1-ethyl-4-nitro-1,2,3-triazole were found from Knudsen measurements. - Abstract: Temperature dependence of the heat capacity and the parameters of phase transitions of 1-ethyl-4-nitro-1,2,3-triazole (1ET) were studied between 5 and 370 K in a vacuum adiabatic calorimeter. Thermodynamic properties of the 1ET in the condensed state were obtained over the range of 0–370 K. Saturated vapor pressure for crystalline 1ET in the temperature ranges from 313 to 344 K and its enthalpy of sublimation were measured by the Knudsen effusion method. The standard enthalpy of formation for crystalline 1ET at 298.15 K was determined in a static bomb combustion calorimeter. From these data, the standard enthalpy of formation for gaseous 1ET was evaluated. The enthalpy of formation calculated using quantum chemical methods is in excellent agreement with the experimental value.

Thermodynamic properties of 1-ethyl-4-nitro-1,2,3-triazole

International Nuclear Information System (INIS)

Blokhin, Andrey V.; Kohut, Sviataslau V.; Kabo, Gennady J.; Stepurko, Elena N.; Paulechka, Yauheni U.; Voitkevich, Olga V.

2013-01-01

Graphical abstract: - Highlights: • Heat capacities and phase transition enthalpies for 1-ethyl-4-nitro-1,2,3-triazole were measured. • Enthalpy of formation for 1-ethyl-4-nitro-1,2,3-triazole was determined. • Vapor pressure and enthalpy of sublimation of 1-ethyl-4-nitro-1,2,3-triazole were found from Knudsen measurements. - Abstract: Temperature dependence of the heat capacity and the parameters of phase transitions of 1-ethyl-4-nitro-1,2,3-triazole (1ET) were studied between 5 and 370 K in a vacuum adiabatic calorimeter. Thermodynamic properties of the 1ET in the condensed state were obtained over the range of 0–370 K. Saturated vapor pressure for crystalline 1ET in the temperature ranges from 313 to 344 K and its enthalpy of sublimation were measured by the Knudsen effusion method. The standard enthalpy of formation for crystalline 1ET at 298.15 K was determined in a static bomb combustion calorimeter. From these data, the standard enthalpy of formation for gaseous 1ET was evaluated. The enthalpy of formation calculated using quantum chemical methods is in excellent agreement with the experimental value

High yield silicon carbide pre-ceramic polymers

International Nuclear Information System (INIS)

Baney, R.H.

1982-01-01

Polysilanes which are substituted with (CH 3 ) 3 SiO-groups are useful for the preparation in high yields of fine grained silicon carbide ceramic materials. They consist of 0 to 60 mole % (CH 3 ) 2 Si units and 100 to 40 mole % CH 3 Si units, all Si valences not satisfied by CH 3 groups or Si atoms being directed to groups (CH 3 ) 3 SiO-, which siloxane groups amount to 23 to 61 weight % of the polysilane. They are prepared by reaction of the corresponding chloro- or bromo-methyl polysilanes with at least the stoichiometric amounts of (CH 3 ) 3 SiOSi(CH 3 ) 3 and water in the presence of a strong acid. (author)

Assessment of Ethyl Carbamate Contamination in Cachaça (Brazilian Sugar Cane Spirit

Directory of Open Access Journals (Sweden)

Aline M. Bortoletto

2016-10-01

Full Text Available Cachaça is a sugar cane spirit produced in Brazil. Ethyl carbamate (EC, a potential carcinogenic compound, may be present in cachaça above the limit established by law. The purpose of this study was to determine the concentration of ethyl carbamate in cachaças recently produced in Brazil in order to verify their compliance with the law. The concentration of ethyl carbamate was determined in 376 samples of cachaça through gas chromatography coupled to a mass spectrometer (GC-MS. The mean value of ethyl carbamate in the cachaças analyzed was 145 µg/L, and 24% of them were not in compliancy with the law (EC < 210 µg/L. However, compared to previous studies, advances have been observed regarding the adjustment of cachaças to the legal limit. Cachaças produced in large distilleries through continuous column distillation presented a mean value of 200 µg/L of ethyl carbamate. Cachaças produced in small distilleries using pot still distillation presented a mean content of 74 µg/L. Small producers have been more engaged in using good manufacturing practices to guarantee the quality of cachaças.

Preparation of superhydrophobic poly(methyl methacrylate)-silicon dioxide nanocomposite films

International Nuclear Information System (INIS)

Wang Jinyan; Chen Xinhua; Kang Yingke; Yang Guangbin; Yu Laigui; Zhang Pingyu

2010-01-01

Superhydrophobic poly(methyl methacrylate)-SiO 2 (coded as PMMA-SiO 2 ) nanocomposite films with micro-nanohierarchical structure were prepared via a simple approach in the absence of low surface-energy compounds. By spin-coating the suspension of hydrophobic silica (SiO 2 ) nanoparticles dispersed in PMMA solution, target nanocomposite films were obtained on glass slides. The wetting behavior of PMMA-SiO 2 nanocomposite films was investigated in relation to the dosage of SiO 2 nanoparticles dispersed in PMMA solution. It was found that hydrophilic PMMA film was transferred to superhydrophobic PMMA-SiO 2 nanocomposite films when hydrophobic SiO 2 nanoparticles were introduced into the PMMA solution at a high enough dosage (0.2 g and above). Resultant PMMA-SiO 2 nanocomposite films had a static water contact angle of above 162 o , showing promising applications in selfcleaning and waterproof for outer wall of building, outer covering for automobile, sanitary wares, and so forth.

Temperature and humidity effect on aging of silicone rubbers as sealing materials for proton exchange membrane fuel cell applications

International Nuclear Information System (INIS)

Chang, Huawei; Wan, Zhongmin; Chen, Xi; Wan, Junhua; Luo, Liang; Zhang, Haining; Shu, Shuiming; Tu, Zhengkai

2016-01-01

Highlights: • Aging of silicone rubbers with different hardness was investigated. • Existed water molecules from humidified gases can accelerate the aging process. • Silicone rubber with hardness of 40 is more suitable as sealing materials. • Silicone rubbers can be used as sealing materials below 80 °C but not above 100 °C. - Abstract: Durability and reliability of seals around perimeter of each unit are critical to the lifetime of proton exchange membrane fuel cells. In this study, we investigate the aging of silicone rubbers with different hardness, often used as sealing materials for fuel cells, subjected to dry and humidified air at different temperatures. The aging properties are characterized by variation of permanent compression set value under compression, mechanical properties, and surface morphology as well. The results show that aging of silicone rubbers becomes more severe with the increase in subjected temperature. At temperature above 100 °C, silicone rubbers are not suitable for fuel cell applications. The existed water molecules from humidified gases can accelerate the aging of silicone rubbers. Among the tested samples, silicone rubber with hardness of 40 is more durable than that with hardness of 30 and 50 for fuel cells. The change of chemical structure after aging suggests that the aging of silicone rubbers mainly results from the chemical decomposition of cross-linker units for connection of polysiloxane backbones and of methyl groups attached to silicon atoms.

Silicon carbide hollow fiber membranes: obtainment and characterization; Membranas de fibra oca de carbeto de silicio: obtencao e caracterizacao

Energy Technology Data Exchange (ETDEWEB)

Oliveira, S.S.L.; Ferreira, R.S.B.; Araujo, B.A.; Medeiros, K.M.; Lucena, H.L.; Araujo, E.M., E-mail: sandriely_sonaly@hotmail.com [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Departamento de Engenharia de Materiais

2016-07-01

Silicon carbide is a promising material for the production of membranes due to its high melting temperature, thermal shock resistance, excellent mechanical and chemical stability. So, this study aims to characterize silicon carbide membranes in order to apply them in the separation of oil-water. A solution (SiC + PES + 1-Methyl- 2-Pyrrolidone) and through the extrusion technique by immersion precipitation membranes were obtained with hollow fiber geometry was prepared. And then sintered at 1500 ° C. For the characterization analyzes were made XRD, FTIR and SEM to evaluate the morphology and composition of the membranes obtained before and after sintering. (author)

Facile synthesis of silicon carbide-titanium dioxide semiconducting nanocomposite using pulsed laser ablation technique and its performance in photovoltaic dye sensitized solar cell and photocatalytic water purification

Energy Technology Data Exchange (ETDEWEB)

Gondal, M.A., E-mail: magondal@kfupm.edu.sa [Laser Research Group, Physics Department & Center of Excellence in Nanotechnology, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Ilyas, A.M. [Laser Research Group, Physics Department & Center of Excellence in Nanotechnology, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Baig, Umair [Laser Research Group, Physics Department & Center of Excellence in Nanotechnology, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Center of Excellence for Scientific Research Collaboration with MIT, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia)

2016-08-15

Highlights: • SiC–TiO{sub 2} semiconducting nanocomposites synthesized by nanosecond PLAL technique. • Synthesized nanocomposites were morphologically and optically characterized. • Nanocomposites were applied for the photocatalytic degradation of toxic organic dye. • Photovoltaic performance was investigated in dye sensitized solar cell. - Abstract: Separation of photo-generated charge carriers (electron and holes) is a major approach to improve the photovoltaic and photocatalytic performance of metal oxide semiconductors. For harsh environment like high temperature applications, ceramic like silicon carbide is very prominent. In this work, 10%, 20% and 40% by weight of pre-oxidized silicon carbide was coupled with titanium dioxide (TiO{sub 2}) to form nanocomposite semiconductor via elegant pulsed laser ablation in liquid technique using second harmonic 532 nm wavelength of neodymium-doped yttrium aluminium garnet (Nd-YAG) laser. In addition, the effect of silicon carbide concentration on the performance of silicon carbide-titanium dioxide nanocomposite as photo-anode in dye sensitized solar cell and as photocatalyst in photodegradation of methyl orange dye in water was also studied. The result obtained shows that photo-conversion efficiency of the dye sensitized solar cell was improved from 0.6% to 1.65% and the percentage of methyl orange dye removed was enhanced from 22% to 77% at 24 min under ultraviolet–visible solar spectrum in the nanocomposite with 10% weight of silicon carbide. This remarkable performance enhancement could be due to the improvement in electron transfer phenomenon by the presence of silicon carbide on titanium dioxide.

Microalgae wet extraction using N-ethyl butylamine for fatty acid production

Directory of Open Access Journals (Sweden)

Ying Du

2016-04-01

Full Text Available Microalgae are considered a promising feedstock for the production of food ingredients, cosmetics, pharmaceutical products and biofuels. The energy intensity of drying and cell breaking of algae and solvent recovery afterwards hindered the route of algae biorefinery. In this work the influences of freeze drying and cell breaking to the extraction efficiency of crude lipid yield and fatty acid yield were investigated. Results showed that drying and cell breaking are not necessary for N-ethyl butylamine extraction, because good yields were obtained without. Crude lipid yield and fatty acid yield using N-ethyl butylamine were comparable with Bligh & Dyer extraction, making N-ethyl butylamine a candidate for further development of an energy efficient lipid extraction technology for non-broken microalgae. Keywords: Microalgae, Lipids, Extraction, Switchable solvent, Secondary amine

Methylation of food commodities during fumigation with methyl bromide

International Nuclear Information System (INIS)

Starratt, A.N.; Bond, E.J.

1990-01-01

Sites of methylation in several commodities (wheat, oatmeal, peanuts, almonds, apples, oranges, maize, alfalfa and potatoes) during fumigation with 14 C-methyl bromide were studied. Differences were observed in levels of the major volatiles: methanol, dimethyl sulphide and methyl mercaptan, products of O- and S-methylation, resulting from treatment of the fumigated materials with 1N sodium hydroxide. In studies of maize and wheat, histidine was the amino acid which underwent the highest level of N-methylation. (author). 24 refs, 3 tabs

Production of FAME biodiesel in E. coli by direct methylation with an insect enzyme.

Science.gov (United States)

Sherkhanov, Saken; Korman, Tyler P; Clarke, Steven G; Bowie, James U

2016-04-07

Most biodiesel currently in use consists of fatty acid methyl esters (FAMEs) produced by transesterification of plant oils with methanol. To reduce competition with food supplies, it would be desirable to directly produce biodiesel in microorganisms. To date, the most effective pathway for the production of biodiesel in bacteria yields fatty acid ethyl esters (FAEEs) at up to ~1.5 g/L. A much simpler route to biodiesel produces FAMEs by direct S-adenosyl-L-methionine (SAM) dependent methylation of free fatty acids, but FAME production by this route has been limited to only ~16 mg/L. Here we employ an alternative, broad spectrum methyltransferase, Drosophila melanogaster Juvenile Hormone Acid O-Methyltransferase (DmJHAMT). By introducing DmJHAMT in E. coli engineered to produce medium chain fatty acids and overproduce SAM, we obtain medium chain FAMEs at titers of 0.56 g/L, a 35-fold increase over titers previously achieved. Although considerable improvements will be needed for viable bacterial production of FAMEs and FAEEs for biofuels, it may be easier to optimize and transport the FAME production pathway to other microorganisms because it involves fewer enzymes.

Solid–liquid phase equilibrium and dissolution properties of ethyl vanillin in pure solvents

International Nuclear Information System (INIS)

Wu, Hao; Wang, Jingkang; Zhou, Yanan; Guo, Nannan; Liu, Qi; Zong, Shuyi; Bao, Ying; Hao, Hongxun

2017-01-01

Highlights: • Solubility of ethyl vanillin in eight pure solvents were determined by a static analytical method. • The experimental solubility data of ethyl vanillin were correlated and analyzed by four thermodynamic models. • Dissolution thermodynamic properties of ethyl vanillin were calculated and discussed. - Abstract: The solubility of ethyl vanillin (EVA) in eight pure solvents were determined in different temperature ranges from (273.15 to 318.15) K by a static analytical method. In the temperature ranges investigated, it was found that the solubility of EVA in all the selected solvents increased with the rising of temperature. Furthermore, four thermodynamic models were used to correlate the experimental solubility data and the calculation results showed that selected models can be used to correlate the solubility data with satisfactory accuracy. Finally, the dissolution thermodynamic properties, including dissolution Gibbs energy, dissolution enthalpy and dissolution entropy of EVA in the eight selected solvents were calculated.

Copper(II) catalysis in cyanide conversion into ethyl carbamate in spirits and relevant reactions.

Science.gov (United States)

Aresta, M; Boscolo, M; Franco, D W

2001-06-01

The role of copper(II) species in the oxidation of inorganic cyanide to cyanate and in the conversion of cyanate or urea into ethyl carbamate was investigated. The oxidation process has been shown to be independent from the dissolved oxygen. Elemental analysis and infrared spectroscopy have shown the formation of a mixed copper carbonate/hydroxide in the process of oxidation of cyanide to cyanate in water/ethanol. The complexation to Cu(II) of cyanate formed upon cyanide oxidation makes the former more susceptible to nucleophilic attack from ethanol, with conversion into ethyl carbamate. Comparatively, urea has a minor role with respect to cyanide in the formation of ethyl carbamate. Therefore, the urea present in some samples of Brazilian sugar cane spirit (cachaça) has been shown to have almost no influence on the ethyl carbamate content of cachaças, which comes essentially from cyanide. Fe(II,III) affords results similar to those found with Cu(II). Some suggestions are presented to avoid ethyl carbamate formation in spirits during distillation.

Microbial community dynamics during the bioremediation process of chlorimuron-ethyl-contaminated soil by Hansschlegelia sp. strain CHL1.

Directory of Open Access Journals (Sweden)

Liqiang Yang

Full Text Available Long-term and excessive application of chlorimuron-ethyl has led to a series of environmental problems. Strain Hansschlegelia sp. CHL1, a highly efficient chlorimuron-ethyl degrading bacterium isolated in our previous study, was employed in the current soil bioremediation study. The residues of chlorimuron-ethyl in soils were detected, and the changes of soil microbial communities were investigated by phospholipid fatty acid (PLFA analysis. The results showed that strain CHL1 exhibited significant chlorimuron-ethyl degradation ability at wide range of concentrations between 10μg kg-1 and 1000μg kg-1. High concentrations of chlorimuron-ethyl significantly decreased the total concentration of PLFAs and the Shannon-Wiener indices and increased the stress level of microbes in soils. The inoculation with strain CHL1, however, reduced the inhibition on soil microbes caused by chlorimuron-ethyl. The results demonstrated that strain CHL1 is effective in the remediation of chlorimuron-ethyl-contaminated soil, and has the potential to remediate chlorimuron-ethyl contaminated soils in situ.

Microbial Community Dynamics during the Bioremediation Process of Chlorimuron-Ethyl-Contaminated Soil by Hansschlegelia sp. Strain CHL1

Science.gov (United States)

Yang, Liqiang; Li, Xinyu; Li, Xu; Su, Zhencheng; Zhang, Chenggang; Zhang, Huiwen

2015-01-01

Long-term and excessive application of chlorimuron-ethyl has led to a series of environmental problems. Strain Hansschlegelia sp. CHL1, a highly efficient chlorimuron-ethyl degrading bacterium isolated in our previous study, was employed in the current soil bioremediation study. The residues of chlorimuron-ethyl in soils were detected, and the changes of soil microbial communities were investigated by phospholipid fatty acid (PLFA) analysis. The results showed that strain CHL1 exhibited significant chlorimuron-ethyl degradation ability at wide range of concentrations between 10μg kg-1 and 1000μg kg-1. High concentrations of chlorimuron-ethyl significantly decreased the total concentration of PLFAs and the Shannon-Wiener indices and increased the stress level of microbes in soils. The inoculation with strain CHL1, however, reduced the inhibition on soil microbes caused by chlorimuron-ethyl. The results demonstrated that strain CHL1 is effective in the remediation of chlorimuron-ethyl-contaminated soil, and has the potential to remediate chlorimuron-ethyl contaminated soils in situ. PMID:25689050

High-temperature unimolecular decomposition of ethyl propionate

KAUST Repository

Giri, Binod; Alabbad, Mohammed; Farooq, Aamir

2016-01-01

This work reports rate coefficients of the thermal unimolecular decomposition reaction of ethyl propionate (EP) behind reflected shock waves over the temperature range of 976–1300 K and pressures of 825–1875 Torr. The reaction progress was monitored

Synthesis of bisaramil labelled with carbon-14 and deuterium

International Nuclear Information System (INIS)

Szammer, J.; Simon-Trompler, E.; Mlinko, S.

1994-01-01

[6,8- 14 C 2 ]-Bisaramil: 3-methyl-7-ethyl-9α-(4-chlorobenzoyloxy)-3,7-diazabicyclo/3. 3.1./nonane-[6,8- 14 C 2 ] monohydrochloride and [7-N-D 5 -ethyl]-Bisaramil: 3-methyl-7-[D 5 -ethyl]-9α-(4-chlorobenzoyloxy)-3,7-diazabicy clo/3.3.1./nonane monohydrochloride were synthesized in four steps from 14 CO 2 (6% overall yield) and in six steps from [D 6 ]-ethanol (4% overall yield), respectively. (Author)

Recognition enhancement of oxidized and methyl-10-undecenoate functionalized porous silicon in gas phase photoluminescence sensing

Czech Academy of Sciences Publication Activity Database

Dian, J.; Vrkoslav, Vladimír; Jelínek, I.

2010-01-01

Roč. 147, - (2010), s. 406-410 ISSN 0925-4005 Institutional research plan: CEZ:AV0Z40550506 Keywords : porous silicon * photoluminescence * sensor * recognition enhancement Subject RIV: CC - Organic Chemistry Impact factor: 3.368, year: 2010

Silicone metalization

Energy Technology Data Exchange (ETDEWEB)

Maghribi, Mariam N. (Livermore, CA); Krulevitch, Peter (Pleasanton, CA); Hamilton, Julie (Tracy, CA)

2008-12-09

A system for providing metal features on silicone comprising providing a silicone layer on a matrix and providing a metal layer on the silicone layer. An electronic apparatus can be produced by the system. The electronic apparatus comprises a silicone body and metal features on the silicone body that provide an electronic device.

Formation of porous silicon oxide from substrate-bound silicon rich silicon oxide layers by continuous-wave laser irradiation

Science.gov (United States)

Wang, Nan; Fricke-Begemann, Th.; Peretzki, P.; Ihlemann, J.; Seibt, M.

2018-03-01

Silicon nanocrystals embedded in silicon oxide that show room temperature photoluminescence (PL) have great potential in silicon light emission applications. Nanocrystalline silicon particle formation by laser irradiation has the unique advantage of spatially controlled heating, which is compatible with modern silicon micro-fabrication technology. In this paper, we employ continuous wave laser irradiation to decompose substrate-bound silicon-rich silicon oxide films into crystalline silicon particles and silicon dioxide. The resulting microstructure is studied using transmission electron microscopy techniques with considerable emphasis on the formation and properties of laser damaged regions which typically quench room temperature PL from the nanoparticles. It is shown that such regions consist of an amorphous matrix with a composition similar to silicon dioxide which contains some nanometric silicon particles in addition to pores. A mechanism referred to as "selective silicon ablation" is proposed which consistently explains the experimental observations. Implications for the damage-free laser decomposition of silicon-rich silicon oxides and also for controlled production of porous silicon dioxide films are discussed.

Transcriptome Profiling to Identify Genes Involved in Mesosulfuron-Methyl Resistance in Alopecurus aequalis

Directory of Open Access Journals (Sweden)

Ning Zhao

2017-08-01

Full Text Available Non-target-site resistance (NTSR to herbicides is a worldwide concern for weed control. However, as the dominant NTSR mechanism in weeds, metabolic resistance is not yet well-characterized at the genetic level. For this study, we have identified a shortawn foxtail (Alopecurus aequalis Sobol. population displaying both TSR and NTSR to mesosulfuron-methyl and fenoxaprop-P-ethyl, yet the molecular basis for this NTSR remains unclear. To investigate the mechanisms of metabolic resistance, an RNA-Seq transcriptome analysis was used to find candidate genes that may confer metabolic resistance to the herbicide mesosulfuron-methyl in this plant population. The RNA-Seq libraries generated 831,846,736 clean reads. The de novo transcriptome assembly yielded 95,479 unigenes (averaging 944 bp in length that were assigned putative annotations. Among these, a total of 29,889 unigenes were assigned to 67 GO terms that contained three main categories, and 14,246 unigenes assigned to 32 predicted KEGG metabolic pathways. Global gene expression was measured using the reads generated from the untreated control (CK, water-only control (WCK, and mesosulfuron-methyl treatment (T of R and susceptible (S. Contigs that showed expression differences between mesosulfuron-methyl-treated R and S biotypes, and between mesosulfuron-methyl-treated, water-treated and untreated R plants were selected for further quantitative real-time PCR (qRT-PCR validation analyses. Seventeen contigs were consistently highly expressed in the resistant A. aequalis plants, including four cytochrome P450 monooxygenase (CytP450 genes, two glutathione S-transferase (GST genes, two glucosyltransferase (GT genes, two ATP-binding cassette (ABC transporter genes, and seven additional contigs with functional annotations related to oxidation, hydrolysis, and plant stress physiology. These 17 contigs could serve as major candidate genes for contributing to metabolic mesosulfuron-methyl resistance; hence

Scrambling free combinatorial labeling of alanine-β, isoleucine-δ1, leucine-proS and valine-proS methyl groups for the detection of long range NOEs

Energy Technology Data Exchange (ETDEWEB)

Kerfah, Rime [NMR-Bio, IBS/CEA (France); Plevin, Michael J. [University of York, Department of Biology (United Kingdom); Pessey, Ombeline [Univ. Grenoble Alpes, Institut de Biologie Structurale (IBS) (France); Hamelin, Olivier [CNRS (France); Gans, Pierre; Boisbouvier, Jerome, E-mail: jerome.boisbouvier@ibs.fr [Univ. Grenoble Alpes, Institut de Biologie Structurale (IBS) (France)

2015-01-15

Specific isotopic labeling of methyl groups in proteins has greatly extended the applicability of solution NMR spectroscopy. Simultaneous labeling of the methyl groups of several different amino acid types can offer a larger number of useful probes that can be used for structural characterisations of challenging proteins. Herein, we propose an improved AILV methyl-labeling protocol in which L and V are stereo-specifically labeled. We show that 2-ketobutyrate cannot be combined with Ala and 2-acetolactate (for the stereo-specific labeling of L and V) as this results in co-incorporation incompatibility and isotopic scrambling. Thus, we developed a robust and cost-effective enzymatic synthesis of the isoleucine precursor, 2-hydroxy-2-(1′-[{sup 2}H{sub 2}], 2′-[{sup 13}C])ethyl-3-keto-4-[{sup 2}H{sub 3}]butanoic acid, as well as an incorporation protocol that eliminates metabolic leakage. We show that application of this labeling scheme to a large 82 kDa protein permits the detection of long-range {sup 1}H–{sup 1}H NOE cross-peaks between methyl probes separated by up to 10 Å.

New phenylethanoids from Buddleja cordata subsp. cordata.

Science.gov (United States)

Acevedo, L; Martínez, E; Castañeda, P; Franzblau, S; Timmermann, B N; Linares, E; Bye, R; Mata, R

2000-04-01

Bioassay-guided fractionation of a crude extract of the stem bark of Buddleja cordata subsp. cordata with significant antimycobacterial activity led to the isolation of a mixture composed by ten new long-chain esters of 2[4'-hydroxyphenyl]-ethanol (1-10), along with the lichen metabolites methyl beta-orcinolcarboxylate (11) and beta-orcinolcarboxylate (12). Extensive HPLC allowed the separation of the major components of the mixture, which were characterized by spectral means as 2[4'-hydroxyphenyl]-ethyl stearate (3), 2[4'-hydroxyphenyl]-ethyl behenate (6), and 2[4'-hydroxyphenyl]-ethyl lignocerate (8). The minor esters were identified as 2[4'-hydroxyphenyl]-ethyl palmitate (1), 2[4'-hydroxyphenyl]-ethyl heptadecanoate (2), 2[4'-hydroxyphenyl]-ethyl nonadecanoate (4), 2[4'-hydroxyphenyl]-ethyl arachidate (5), 2[4'-hydroxyphenyl]-ethyl tricosanoate (7), 2[4'-hydroxyphenyl]-ethyl pentacosanoate (9), and 2[4'-hydroxyphenyl]-ethyl hexacosanoate (10) by GC-MS analysis of the methyl esters derivatives of the fatty acids obtained by alkaline hydrolysis of the mixture. Compound 8 exhibited moderate antibacterial activity against Mycobacterium tuberculosis (MIC = 64 micrograms/ml).

Oxygen defect processes in silicon and silicon germanium

KAUST Repository

Chroneos, A.

2015-06-18

Silicon and silicon germanium are the archetypical elemental and alloy semiconductor materials for nanoelectronic, sensor, and photovoltaic applications. The investigation of radiation induced defects involving oxygen, carbon, and intrinsic defects is important for the improvement of devices as these defects can have a deleterious impact on the properties of silicon and silicon germanium. In the present review, we mainly focus on oxygen-related defects and the impact of isovalent doping on their properties in silicon and silicon germanium. The efficacy of the isovalent doping strategies to constrain the oxygen-related defects is discussed in view of recent infrared spectroscopy and density functional theory studies.

Oxygen defect processes in silicon and silicon germanium

KAUST Repository

Chroneos, A.; Sgourou, E. N.; Londos, C. A.; Schwingenschlö gl, Udo

2015-01-01

Silicon and silicon germanium are the archetypical elemental and alloy semiconductor materials for nanoelectronic, sensor, and photovoltaic applications. The investigation of radiation induced defects involving oxygen, carbon, and intrinsic defects is important for the improvement of devices as these defects can have a deleterious impact on the properties of silicon and silicon germanium. In the present review, we mainly focus on oxygen-related defects and the impact of isovalent doping on their properties in silicon and silicon germanium. The efficacy of the isovalent doping strategies to constrain the oxygen-related defects is discussed in view of recent infrared spectroscopy and density functional theory studies.

MethylMix 2.0: an R package for identifying DNA methylation genes.

Science.gov (United States)

Cedoz, Pierre-Louis; Prunello, Marcos; Brennan, Kevin; Gevaert, Olivier

2018-04-14

DNA methylation is an important mechanism regulating gene transcription, and its role in carcinogenesis has been extensively studied. Hyper and hypomethylation of genes is a major mechanism of gene expression deregulation in a wide range of diseases. At the same time, high-throughput DNA methylation assays have been developed generating vast amounts of genome wide DNA methylation measurements. We developed MethylMix, an algorithm implemented in R to identify disease specific hyper and hypomethylated genes. Here we present a new version of MethylMix that automates the construction of DNA-methylation and gene expression datasets from The Cancer Genome Atlas (TCGA). More precisely, MethylMix 2.0 incorporates two major updates: the automated downloading of DNA methylation and gene expression datasets from TCGA and the automated preprocessing of such datasets: value imputation, batch correction and CpG sites clustering within each gene. The resulting datasets can subsequently be analyzed with MethylMix to identify transcriptionally predictive methylation states. We show that the Differential Methylation Values created by MethylMix can be used for cancer subtyping. olivier.gevaert@stanford.edu. https://bioconductor.org/packages/release/bioc/manuals/MethylMix/man/MethylMix.pdf. MethylMix 2.0 was implemented as an R package and is available in bioconductor.

Global DNA methylation analysis using methyl-sensitive amplification polymorphism (MSAP).

Science.gov (United States)

Yaish, Mahmoud W; Peng, Mingsheng; Rothstein, Steven J

2014-01-01

DNA methylation is a crucial epigenetic process which helps control gene transcription activity in eukaryotes. Information regarding the methylation status of a regulatory sequence of a particular gene provides important knowledge of this transcriptional control. DNA methylation can be detected using several methods, including sodium bisulfite sequencing and restriction digestion using methylation-sensitive endonucleases. Methyl-Sensitive Amplification Polymorphism (MSAP) is a technique used to study the global DNA methylation status of an organism and hence to distinguish between two individuals based on the DNA methylation status determined by the differential digestion pattern. Therefore, this technique is a useful method for DNA methylation mapping and positional cloning of differentially methylated genes. In this technique, genomic DNA is first digested with a methylation-sensitive restriction enzyme such as HpaII, and then the DNA fragments are ligated to adaptors in order to facilitate their amplification. Digestion using a methylation-insensitive isoschizomer of HpaII, MspI is used in a parallel digestion reaction as a loading control in the experiment. Subsequently, these fragments are selectively amplified by fluorescently labeled primers. PCR products from different individuals are compared, and once an interesting polymorphic locus is recognized, the desired DNA fragment can be isolated from a denaturing polyacrylamide gel, sequenced and identified based on DNA sequence similarity to other sequences available in the database. We will use analysis of met1, ddm1, and atmbd9 mutants and wild-type plants treated with a cytidine analogue, 5-azaC, or zebularine to demonstrate how to assess the genetic modulation of DNA methylation in Arabidopsis. It should be noted that despite the fact that MSAP is a reliable technique used to fish for polymorphic methylated loci, its power is limited to the restriction recognition sites of the enzymes used in the genomic

Preparation of superhydrophobic poly(methyl methacrylate)-silicon dioxide nanocomposite films

Energy Technology Data Exchange (ETDEWEB)

Wang Jinyan [Key Laboratory of Ministry of Education for Special Functional Materials, Henan University, Jinming Road, Kaifeng, Henan Province 475004 (China); Chen Xinhua [Key Laboratory of Ministry of Education for Special Functional Materials, Henan University, Jinming Road, Kaifeng, Henan Province 475004 (China); College of Chemistry and Chemical Engineering, Xuchang University, Xuchang 461000 (China); Kang Yingke; Yang Guangbin; Yu Laigui [Key Laboratory of Ministry of Education for Special Functional Materials, Henan University, Jinming Road, Kaifeng, Henan Province 475004 (China); Zhang Pingyu, E-mail: pingyu@henu.edu.cn [Key Laboratory of Ministry of Education for Special Functional Materials, Henan University, Jinming Road, Kaifeng, Henan Province 475004 (China)

2010-12-15

Superhydrophobic poly(methyl methacrylate)-SiO{sub 2} (coded as PMMA-SiO{sub 2}) nanocomposite films with micro-nanohierarchical structure were prepared via a simple approach in the absence of low surface-energy compounds. By spin-coating the suspension of hydrophobic silica (SiO{sub 2}) nanoparticles dispersed in PMMA solution, target nanocomposite films were obtained on glass slides. The wetting behavior of PMMA-SiO{sub 2} nanocomposite films was investigated in relation to the dosage of SiO{sub 2} nanoparticles dispersed in PMMA solution. It was found that hydrophilic PMMA film was transferred to superhydrophobic PMMA-SiO{sub 2} nanocomposite films when hydrophobic SiO{sub 2} nanoparticles were introduced into the PMMA solution at a high enough dosage (0.2 g and above). Resultant PMMA-SiO{sub 2} nanocomposite films had a static water contact angle of above 162{sup o}, showing promising applications in selfcleaning and waterproof for outer wall of building, outer covering for automobile, sanitary wares, and so forth.

Characterization of the radioactive metabolites of the 5-HT1A receptor radioligand, [O-methyl-C-11]WAY-100635, in monkey and human plasma by HPLC : Comparison of the behaviour of an identified radioactive metabolite with parent radioligand in monkey using PET

NARCIS (Netherlands)

Osman, S; Lundkvist, C; Pike, VW; Halldin, C; McCarron, JA; Swahn, CG; Ginovart, N; Luthra, SK; Bench, CJ; Grasby, PM; Wikstrom, H; Barf, T; Cliffe, IA; Fletcher, A; Farde, L

N-(2-(4-(2-Methoxy-phenyl)-1-piperazin-1-yl)ethyl)-N-(2-pyridyl)cyclohexanecarboxamide (WAY-100635), labelled in the O-methyl group with carbon-11 (t(1/2) = 20.4 min), is a promising radioligand for application with positron emission tomography (PET) to the study of 5-HT1A receptors in living human

Successful topical dissolution of cholesterol gallbladder stones using ethyl propionate.

Science.gov (United States)

Hofmann, A F; Amelsberg, A; Esch, O; Schteingart, C D; Lyche, K; Jinich, H; Vansonnenberg, E; D'Agostino, H B

1997-06-01

Topical dissolution of cholesterol gallbladder stones using methyl tert-butyl ether (MTBE) is useful in symptomatic patients judged too ill for surgery. Previous studies showed that ethyl propionate (EP), a C5 ester, dissolves cholesterol gallstones rapidly in vitro, but differs from MTBE in being eliminated so rapidly by the liver that blood levels remain undetectable. Our aim was to test EP as a topical dissolution agent for cholesterol gallbladder stones. Five high-risk patients underwent topical dissolution of gallbladder stones by EP. In three patients, the solvent was instilled via a cholecystostomy tube placed previously to treat acute cholecystitis; in two patients, a percutaneous transhepatic catheter was placed in the gallbladder electively. Gallstone dissolution was assessed by chromatography, by gravimetry, and by catheter cholecystography. Total dissolution of gallstones was obtained in four patients after 6-10 hr of lavage; in the fifth patient, partial gallstone dissolution facilitated basketing of the stones. In two patients, cholesterol dissolution was measured and averaged 30 mg/min. Side effects were limited to one episode of transient hypotension and pain at the infusion site; no patient developed somnolence or nausea. Gallstone elimination was associated with relief of symptoms. EP is an acceptable alternative to MTBE for topical dissolution of cholesterol gallbladder stones in high-risk patients. The lower volatility and rapid hepatic extraction of EP suggest that it may be preferable to MTBE in this investigational procedure.

Contact dermatitis to ethyl-cyanoacrylate-containing glue.

Science.gov (United States)

Belsito, D V

1987-10-01

3 patients with contact dermatitis to an ethyl cyanoacrylate glue are presented. Although reactions to cyanoacrylate glues are considered rare, more widespread use of these products by nail salons is likely to be associated with an increased incidence of positive reactions. All 3 of our patients came into contact with the glue during "nail wrapping". In this process, ethyl cyanoacrylate or another "instant glue" is used to adhere glue-impregnated silk or linen to the nail plate which is then filed to shape the nail. This procedure creates fine acrylic-containing dust which may facilitate an allergic response. Fine particulate matter may be transferred to other distant cutaneous sites, such as the eyelids, resulting in more widespread cutaneous eruptions. Dermatologists in areas where nail wrapping is becoming more fashionable are advised to be alert to potential cyanoacrylate glue allergies which present as periungual eczema which may be associated with eyelid dermatitis and features of nummular dermatitis particularly over the dorsal hand.

Randomized controlled trial of ethyl-eicosapentaenoic acid in Huntington disease: the TREND-HD study.

Science.gov (United States)

2008-12-01

To determine whether ethyl-eicosapentaenoic acid (ethyl-EPA), an omega-3 fatty acid, improves the motor features of Huntington disease. Six-month multicenter, randomized, double-blind, placebo-controlled trial followed by a 6-month open-label phase without disclosing initial treatment assignments. Forty-one research sites in the United States and Canada. Three hundred sixteen adults with Huntington disease, enriched for a population with shorter trinucleotide (cytosine-adenine-guanine) repeat length expansions. Random assignment to placebo or ethyl-EPA, 1 g twice a day, followed by open-label treatment with ethyl-EPA. Six-month change in the Total Motor Score 4 component of the Unified Huntington's Disease Rating Scale analyzed for all research participants and those with shorter cytosine-adenine-guanine repeat length expansions (<45). At 6 months, the Total Motor Score 4 point change for patients receiving ethyl-EPA did not differ from that for those receiving placebo. No differences were found in measures of function, cognition, or global impression. Before public disclosure of the 6-month placebo-controlled results, 192 individuals completed the open-label phase. The Total Motor Score 4 change did not worsen for those who received active treatment for 12 continuous months compared with those who received active treatment for only 6 months (2.0-point worsening; P=.02). Ethyl-EPA was not beneficial in patients with Huntington disease during 6 months of placebo-controlled evaluation. Clinical Trial Registry clinicaltrials.gov Identifier: NCT00146211.

The synthesis of 5-(1- sup 11 C)ethyl barbiturates from labelled malonic esters

Energy Technology Data Exchange (ETDEWEB)

Gee, A.; Laangstroem, B. (Uppsala Univ. (Sweden). Dept. of Organic Chemistry)

1991-01-01

The synthesis of ({sup 11}C)phenobarbital, ({sup 11}C)pentobarbital and({sup 11}C)amobarbital labelled in the 5-(1-{sup 11}C)ethyl position is reported. The malonic esters R- CH(CO{sub 2}Et){sub 2} R phenyl-, 1-methylbutyl-, and 3- methylbutyl- were alkylated with (1-{sup 11}C)ethyl iodide prepared from ({sup 11}C)carbon dioxide. Ring closure of the 2-(1-{sup 11}C)ethyl-labelled malonic esters with urea afforded 5-(1-{sup 11}C)ethyl-phenobarbital,-phenobarbital, -pentobarbital and -amobarbital synthesis times of 42-47 min, counted from ({sup 11}C) carbon dioxide. In typical syntheses starting with 3 GBq pentobarbitol and (81 mCi) ({sup 11}C)carbon dioxide, 150-215 MBq (4-6 mCi) were produced in 25-30% decay corrected -amobarbital radiochemical yields with radiochemical purities greater than 98%. (author).

A New Phenyl Ethyl Glycoside from the Twigs of Acer tegmentosum.

Science.gov (United States)

Park, Seonju; Lee, Hwa Young; Nhiem, Nguyen Xuan; Lee, Taek Hwan; Kim, Nanyoung; Cho, Seung Hun; Kim, Seung Hyun

2015-07-01

One new phenyl ethyl glycoside, 2-(4-hydroxyphenyl)ethyl-O-α-L-arabinofuranosyl-(1 --> 6)-O-β-D-glucopyranoide (1) and 11 known compounds (2-12) were isolated from the twigs of Acer tegmentosum. Compound 6 showed potent anti-neuroinflammatory activity against the LPS-stimulated BV-2 microglial cells with tNO production of 25.0 ± 2.5 μM and TNF-α concentration of 617.6 ± 47.1 pg/mL at 30 μM.

Carbon-11 labelling of eticlopride in two different positions - a selective high-affinity ligand for the study of dopamine D-2 receptors using PET

International Nuclear Information System (INIS)

Halldin, Christer; Hall, Haakan

1990-01-01

A new highly selective high-affinity dopamine D-2 receptor antagonist, eticlopride ((-)-(S)-5-chloro-3-ethyl-N-(1-ethyl-2-pyrrolidinyl)methyl)-6-methoxysalicylamide), was labelled with 11 C in two different positions ([N-ethyl- 11 C]eticlopride (I) and ([methyl- 11 C]eticlopride (II)). Product I was prepared by N-alkylation of the N-desethyl compound with [ 11 C]ethyl iodide. II was prepared by O-alkylation of the diphenolic precursor with [ 11 C]methyl iodide followed by separation of the two methylated products. The radiochemical yields were 15-20% (EOB) with an overall synthesis time of 45-60 min. Both compounds were isolated by semi-preparative HPLC and the radiochemical purity was in both cases > 99%. I was injected i.v. in a Cynomolgus monkey and brain radioactivity was measured by positron emission tomography (PET). The specific activity was 70 Ci/mmol at time of injection. There was a marked accumulation of radioactivity in the basal ganglia, regions known to have a high density of dopamine D-2 receptors. (author)

Performance and emission characteristics of a DI compression ignition engine operated on Honge, Jatropha and sesame oil methyl esters

Energy Technology Data Exchange (ETDEWEB)

Banapurmath, N.R.; Tewari, P.G. [Department of Mechanical Engineering, B.V.B. College of Engineering and Technology, Vidyanagar, Poona-Bangalore Road, Hubli 580031 (India); Hosmath, R.S. [Department of Mechanical Engineering, K.L.E' s C.E.T., Belgaum (India)

2008-09-15

The high viscosity of vegetable oils leads to problem in pumping and spray characteristics. The inefficient mixing of vegetable oils with air contributes to incomplete combustion. The best way to use vegetable oils as fuel in compression ignition (CI) engines is to convert it into biodiesel. Biodiesel is a methyl or ethyl ester of fatty acids made from vegetable oils (both edible and non-edible) and animal fat. The main resources for biodiesel production can be non-edible oils obtained from plant species such as Pongamia pinnata (Honge oil), Jatropha curcas (Ratanjyot), Hevea brasiliensis (Rubber) and Calophyllum inophyllum (Nagchampa). Biodiesel can be used in its pure form or can be blended with diesel to form different blends. It can be used in CI engines with very little or no engine modifications. This is because it has properties similar to mineral diesel. This paper presents the results of investigations carried out on a single-cylinder, four-stroke, direct-injection, CI engine operated with methyl esters of Honge oil, Jatropha oil and sesame oil. Comparative measures of brake thermal efficiency, smoke opacity, HC, CO, NO{sub X}, ignition delay, combustion duration and heat release rates have been presented and discussed. Engine performance in terms of higher brake thermal efficiency and lower emissions (HC, CO, NO{sub X}) with sesame oil methyl ester operation was observed compared to methyl esters of Honge and Jatropha oil operation. (author)

Identification, characterization and quantification of new impurities by LC-ESI/MS/MS and LC-UV methods in rivastigmine tartrate active pharmaceutical ingredient.

Science.gov (United States)

Thomas, Saji; Shandilya, Sanjeev; Bharati, Amber; Paul, Saroj Kumar; Agarwal, Ashutosh; Mathela, Chandra S

2012-01-05

Six impurities were detected at trace level in rivastigmine tartrate drug substance by a newly developed high performance liquid chromatography method. Three impurities were characterized rapidly and three impurities were found to be unknown. The unknown impurities were enriched and identified with a combination of semi-preparative HPLC and LC/MS/MS techniques. Proposed structures were further confirmed by characterization using NMR, FT-IR, and EA techniques of impurity standards. Based on the spectroscopic, spectrometric and elemental analysis data unknown impurities were characterized as 3-[1-(dimethylamino)ethyl]phenyl N-ethyl-N-methyl carbamate N-oxide, ethyl-methyl-carbamic acid 4-(1-dimethylamino-ethyl)-phenyl ester and ethyl-methyl-carbamic acid 2-(1-dimethylamino-ethyl)-phenyl ester. A plausible mechanism for the formation of these impurities is also proposed. The method was validated according to ICH guidelines for fourteen impurities to demonstrate specificity, precision, linearity, accuracy and stability indicating nature of the method. Regression analysis showed correlation coefficient value greater than 0.999 for rivastigmine tartrate and its impurities. Accuracy of the method was established based on the recovery obtained between 93.41 and 113.33% for all impurities. Copyright © 2011 Elsevier B.V. All rights reserved.

Systemic effects of chronically administered methyl prednisolonate and methyl 17-deoxyprednisolonate.

Science.gov (United States)

Olejniczak, E; Lee, H J

1984-06-01

The systemic activities of methyl prednisolonate and methyl 17-deoxyprednisolonate (1) were studied in rats. Methyl 17-deoxyprednisolonate produced significant changes in the amount of sodium ion (decreased) and potassium ion (increased) in urine; however, methyl prednisolonate had no effect on electrolyte balance. Both methyl prednisolonate and methyl 17-deoxyprednisolonate had no effect on liver glycogen content, plasma corticosterone level and relative adrenal weight. In contrast, the parent compound prednisolone caused a significant decrease in liver glycogen content, plasma corticosterone level and relative adrenal weight.

P3HT:PCBM Incorporated with Silicon Nanoparticles as Photoactive Layer in Efficient Organic Photovoltaic Devices

Directory of Open Access Journals (Sweden)

Shang-Chou Chang

2013-01-01

Full Text Available Silicon nanoparticles doped poly(3-hexylthiophene and [6,6]-phenyl C61-butyric acid methyl ester blends (P3HT:PCBM: Si NP have been produced as the photoactive layer of organic photovoltaic devices (OPVs. The silicon nanoparticles’ size is between 80 and 100 nm checked by transmission electron microscope (TEM. The 0.35 wt% Si NP doping OPVs exhibit higher power conversion efficiency (PCE than other OPVs. The PCE of the OPVs increases from 3.01% to 3.38% mainly due to increasing short-circuit current density from 8.38 to 9.48 mA/cm2, while the open-circuit voltage remains the same. The Si NP can provide extra exciton separation and electron pathways in hybrid solar cells.

Transesterified milkweed (Asclepias) seed oil as a biodiesel fuel

Energy Technology Data Exchange (ETDEWEB)

Ronald Alan Holser; Rogers Harry-O' Kurua [United States Department of Agriculture, Peoria, IL (United States). Agricultural Research Service, National Center for Utilization Research

2006-10-15

The methyl and ethyl esters of milkweed (Asclepias) seed oil were prepared and compared to soybean esters in laboratory tests to determine biodiesel fuel performance properties. The pour points of the methyl and ethyl milkweed esters measured -6{sup o}C and -10{sup o}C, respectively, which is consistent with the high levels of unsaturation characteristic of milkweed seed oil. The oxidative stabilities measured by OSI at 100{sup o}C were between 0.8 and 4.1 h for all samples tested. The kinematic viscosities determined at 40{sup o}C by ASTM D 445 averaged 4.9 mm{sup 2}/s for milkweed methyl esters and 4.2 mm{sup 2}/s for soybean methyl esters. Lubricity values determined by ASTM D 6079 at 60{sup o}C were comparable to the corresponding soybean esters with average ball wear scar values of 118 {mu}m for milkweed methyl esters and 200 {mu}m for milkweed ethyl esters.

Novel recombinant ethyl ferulate esterase from Burkholderia multivorans

CSIR Research Space (South Africa)

Rashamuse, KJ

2007-11-01

Full Text Available Isolation and identification of bacterial isolates with specific ferulic acid (FA) esterase activity and cloning of a gene encoding activity. A micro-organism with ethyl ferulate hydrolysing (EFH) activity was isolated by culture enrichment...

Fast detoxication of 2-chloro ethyl ethyl sulfide by p-type Ag_2O semiconductor nanoparticle-loaded Al_2O_3-based supports

International Nuclear Information System (INIS)

Ma, Meng-Wei; Kuo, Dong-Hau

2016-01-01

Highlights: • Detoxication of CWA surrogate of 2-chloro ethyl ethyl sulfide is investigated. • A small amount of Ag_2O on Al_2O_3-base support is sufficient to degrade 2-CEES. • Detoxication conversion >82% in 15 min is achieved for >2.5% Ag_2O/Na_2SiO_3/Al_2O_3. • Na_2SiO_3 modified Al_2O_3 to have the valley-like line pattern for depositing Ag_2O. • 2-CEES oxidation is initiated from the dominant electronic holes in p-type Ag_2O. - Abstract: p-type Ag_2O semiconductor nanoparticle-loaded Al_2O_3 or Na_2SiO_3/Al_2O_3 powders used for detoxicating the surrogate of sulfur mustard of 2-chloro ethyl ethyl sulfide (C_2H_5SCH_2CH_2Cl, 2-CEES) were investigated. Different amounts of Ag_2O and Na_2SiO_3 on catalyst supports were evaluated. Gas chromatography with a pulsed flame photometric detector (GC–PFPD) and gas chromatography coupled with a mass spectroscopy (GC–MS) were used to monitor and identify the catalytic reactions, together with reaction products analysis. The GC analyses showed that the decontamination of 2-CEES in isopropanol solvent for 15 min was above 82% efficiency for the 0.5% Na_2SiO_3/Al_2O_3 support deposited with a Ag_2O content above 2.5%. 2-(ethylthio)ethanol and 2-(ethylthio)ethanoic acid were identified as the major products after catalytic reactions. The electronic holes dominating in p-type Ag_2O is proposed to provide the key component and to initiate the catalytic reactions. The electronic hole-based detoxication mechanism is proposed.

Silicon epitaxy on textured double layer porous silicon by LPCVD

International Nuclear Information System (INIS)

Cai Hong; Shen Honglie; Zhang Lei; Huang Haibin; Lu Linfeng; Tang Zhengxia; Shen Jiancang

2010-01-01

Epitaxial silicon thin film on textured double layer porous silicon (DLPS) was demonstrated. The textured DLPS was formed by electrochemical etching using two different current densities on the silicon wafer that are randomly textured with upright pyramids. Silicon thin films were then grown on the annealed DLPS, using low-pressure chemical vapor deposition (LPCVD). The reflectance of the DLPS and the grown silicon thin films were studied by a spectrophotometer. The crystallinity and topography of the grown silicon thin films were studied by Raman spectroscopy and SEM. The reflectance results show that the reflectance of the silicon wafer decreases from 24.7% to 11.7% after texturing, and after the deposition of silicon thin film the surface reflectance is about 13.8%. SEM images show that the epitaxial silicon film on textured DLPS exhibits random pyramids. The Raman spectrum peaks near 521 cm -1 have a width of 7.8 cm -1 , which reveals the high crystalline quality of the silicon epitaxy.

(Vapor + liquid) equilibrium for the binary systems {l_brace}water + glycerol{r_brace} and {l_brace}ethanol + glycerol, ethyl stearate, and ethyl palmitate{r_brace} at low pressures

Energy Technology Data Exchange (ETDEWEB)

Coelho, Renata; Santos, Priscilla G. dos; Mafra, Marcos R. [Department of Chemical Engineering, Federal University of Parana, CEP 81531-990, Curitiba, PR (Brazil); Cardozo-Filho, Lucio [Department of Chemical Engineering, Maringa State University (UEM), Av. Colombo 5790, 87020-900 Maringa, PR (Brazil); Corazza, Marcos L., E-mail: corazza@ufpr.br [Department of Chemical Engineering, Federal University of Parana, CEP 81531-990, Curitiba, PR (Brazil)

2011-12-15

Highlights: > We measured VLE for the binary system {l_brace}ethyl stearate and palmitate + ethanol{r_brace}. > The boiling temperatures were obtained using Othmer-type ebuliometer. > The experimental data were modeled using NRTL, UNIQUAC, and UNIFAC models. - Abstract: This work reports the experimental measurements {l_brace}(vapor + liquid) equilibrium{r_brace} for the systems {l_brace}water(1) + glycerol(2){r_brace}, {l_brace}ethanol(1) + glycerol(2){r_brace}, {l_brace}ethanol(1) + ethyl stearate(2){r_brace}, and {l_brace}ethanol(1) + ethyl palmitate(2){r_brace}. Boiling temperatures were measured using an Othmer-type ebulliometer over a pressure range of 14 kPa to 96 kPa. The experimental data were well correlated using the NRTL and UNIQUAC models. The performance of the UNIFAC-Dortmund model in relation to predicting the phase equilibrium of the systems was also studied.

A Simple, Safe Method for Preparation of Biodiesel

Science.gov (United States)

Behnia, Mahin S.; Emerson, David W.; Steinberg, Spencer M.; Alwis, Rasika M.; Duenas, Josue A.; Serafino, Jessica O.

2011-01-01

An experiment suitable for organic chemistry students is described. Biodiesel, a "green" fuel, consists of methyl or ethyl esters of long-chain fatty acids called FAMES (fatty acid methyl esters) or FAEES (fatty acid ethyl esters). A quick way to make FAMES is a base-catalyzed transesterification of oils or fats derived from plants or from animal…

Evaluation Lactogenic Activity of Ethyl Acetate Fraction of Torbangun (Coleus amboinicus L.) Leaves

Science.gov (United States)

Damanik, R. M.; Kustiyah, L.; Hanafi, M.; Iwansyah, A. C.

2017-12-01

This study aimed to assess the lactogenic property of ethyl acetate fraction of torbangun (Coleus amboinicus L.) leaves and to identify the compounds that responsibility as ‘milk booster’ using LC- MS approach. Lactagogue activity was evaluated in terms of quantity of milk produced from the rats treated with commercial milk booster (AF), ethyl acetate fraction of torbangun leaves (EA), water extraction of torbangun (AQ) and kaempferol (KP). The feed was given orally every two days and starting from Day 2 after giving birth until Day 28. The performance of milk production was measured along the experimental period by weight-suckle-weight method. The level of prolactin serum was determined by ELISA methods. Histopathological analysis of mammary gland, liver, intestines and kidney tissues was carried out. Moreover, in order to profiling and identification of compounds of ethyl acetate fraction, ultra-performance liquid chromatography quadrupole time of flight to electrospray ionization mass spectrometry (UPLC-QTOF-ESI-MS) in the positive-ion mode was performed. The ethyl acetate fraction of torbangun leaves (EA) was induced milk production about 17%, and AF 22% and KP 51% compared to the control group. Meanwhile, the EA was not significantly stimulate the synthesis of serum prolactin at Day 14 and Day 28 (p>0.05). Administration of EA did not cause any signs or symptoms of toxicity. In addition, a total of ten compounds was identified by UPLC-QTOF-ESI/MS in the ethyl acetate fraction of the leaves of C. amboinicus, mostly phenolic compounds, flavonols and some of their glycoside derivatives, such as: digiprolatone, and kaempferol-3-7-O-di-rhamnopyranoside. The present study reveals the ethyl acetate fraction of torbangun leaves and its bioactive compounds has the potency as a remedy for stimulating and improving milk production.

Simultaneous exposure to ethyl benzene and noise : synergistic effects on outer hair cells

NARCIS (Netherlands)

Cappaert, N.L.M.; Klis, S.F.L.; Muijser, H.; Kulig, B.M.; Smoorenburg, G.F.

2001-01-01

The effects on hearing of simultaneous exposure to the ototoxic organic solvent ethyl benzene and broad-band noise were evaluated in rats. The effects of three ethyl benzene concentrations (0, 300 or 400 ppm) and three noise levels (95 or 105 dBlin SPL or background noise at 65 dBlin SPL) and all

Solution Properties of Water-Soluble “Smart” Poly(N-acryloyl-N′-ethyl piperazine-co-methyl methacrylate

Directory of Open Access Journals (Sweden)

G. Roshan Deen

2012-01-01

Full Text Available Water-soluble copolymers of N-acryloyl-N′-ethylpiperazine (AcrNEP with methyl methacrylate (MMA were synthesized to high conversion by free-radical solution polymerization. The composition of the copolymers was determined using Fourier Transform Infra-red Spectroscopy (FTIR. Copolymers containing AcrNEP content above 44 mol% were readily soluble in water and exhibited the critical solution temperature behavior. The copolymers were strongly responsive to changes in pH of the external medium due to the presence of tertiary amine functions that could be protonated at low pH. The influence of various factors such as copolymer composition, pH, temperature, salt and surfactant concentration on the LCST of the copolymers were systematically studied. The intrinsic viscosity of the copolymers in dimethyl formamide decreased with increase in temperature due to a decrease in thermodynamic affinity between polymer chains and solvent molecules. The viscosity behavior of the copolymers in sodium chloride solution was similar to that of classical polyelectrolytes and hydrophobically modified polyacrylate systems.

Electrospun water-stable zein/ethyl cellulose composite nanofiber and its drug release properties

Energy Technology Data Exchange (ETDEWEB)

Lu, Hangyi; Wang, Qingqing; Li, Guohui [Key Laboratory of Eco-textiles, Jiangnan University, Wuxi (China); Qiu, Yuyu [Key Laboratory of Eco-textiles, Jiangnan University, Wuxi (China); Laboratory of Natural Medicine, Wuxi Medical School, Jiangnan University (China); Wei, Qufu, E-mail: qfwei@jiangnan.edu.cn [Key Laboratory of Eco-textiles, Jiangnan University, Wuxi (China)

2017-05-01

A simple and cost-effective way to prepare water-stable zein-based nanofibers for potential drug delivery was presented in this article. Corn protein zein was co-electrospun with hydrophobic ethyl cellulose. Indomethacin, as a model drug, was incorporated in situ into the composite nanofibers. Scanning electron microscopy and element mapping revealed the morphologies of drug-loaded nanofibers and drug distribution, respectively. Fourier transform infrared spectra confirmed the physical blending among the components. Differential scanning calorimetry and X-ray diffraction demonstrated the physical state of drug and polymers in the nanofiber matrix. The composite nanofibers showed a sustained diffusion-controlled release according to the results of in vitro dissolution tests. - Highlights: • A simple, non-toxic and cost-effective way to improve water stability of zein nanofibers was proposed. • Electrospun zein/ethyl cellulose nanofibers with improved water stability and mechanical strength were prepared. • Indomethacin was homogeneously distributed in the zein/ethyl cellulose nanofibers with no aggregation or cluster. • The zein/ethyl cellulose nanofibers presented a sustained drug release profile, following Fickican diffusion mechanism.

Ethyl Pyruvate Ameliorates Hepatic Ischemia-Reperfusion Injury by Inhibiting Intrinsic Pathway of Apoptosis and Autophagy

Directory of Open Access Journals (Sweden)

Miao Shen

2013-01-01

Full Text Available Background. Hepatic ischemia-reperfusion (I/R injury is a pivotal clinical problem occurring in many clinical conditions such as transplantation, trauma, and hepatic failure after hemorrhagic shock. Apoptosis and autophagy have been shown to contribute to cell death in hepatic I/R injury. Ethyl pyruvate, a stable and simple lipophilic ester, has been shown to have anti-inflammatory properties. In this study, the purpose is to explore both the effect of ethyl pyruvate on hepatic I/R injury and regulation of intrinsic pathway of apoptosis and autophagy. Methods. Three doses of ethyl pyruvate (20 mg/kg, 40 mg/kg, and 80 mg/kg were administered 1 h before a model of segmental (70% hepatic warm ischemia was established in Balb/c mice. All serum and liver tissues were obtained at three different time points (4 h, 8 h, and 16 h. Results. Alanine aminotransferase (ALT, aspartate aminotransferase (AST, and pathological features were significantly ameliorated by ethyl pyruvate (80 mg/kg. The expression of Bcl-2, Bax, Beclin-1, and LC3, which play an important role in the regulation of intrinsic pathway of apoptosis and autophagy, was also obviously decreased by ethyl pyruvate (80 mg/kg. Furthermore, ethyl pyruvate inhibited the HMGB1/TLR4/ NF-κb axis and the release of cytokines (TNF-α and IL-6. Conclusion. Our results showed that ethyl pyruvate might attenuate to hepatic I/R injury by inhibiting intrinsic pathway of apoptosis and autophagy, mediated partly through downregulation of HMGB1/TLR4/ NF-κb axis and the competitive interaction with Beclin-1 of HMGB1.

Production of electronic grade lunar silicon by disproportionation of silicon difluoride

Science.gov (United States)

Agosto, William N.

1993-01-01

Waldron has proposed to extract lunar silicon by sodium reduction of sodium fluorosilicate derived from reacting sodium fluoride with lunar silicon tetrafluoride. Silicon tetrafluoride is obtained by the action of hydrofluoric acid on lunar silicates. While these reactions are well understood, the resulting lunar silicon is not likely to meet electronic specifications of 5 nines purity. Dale and Margrave have shown that silicon difluoride can be obtained by the action of silicon tetrafluoride on elemental silicon at elevated temperatures (1100-1200 C) and low pressures (1-2 torr). The resulting silicon difluoride will then spontaneously disproportionate into hyperpure silicon and silicon tetrafluoride in vacuum at approximately 400 C. On its own merits, silicon difluoride polymerizes into a tough waxy solid in the temperature range from liquid nitrogen to about 100 C. It is the silicon analog of teflon. Silicon difluoride ignites in moist air but is stable under lunar surface conditions and may prove to be a valuable industrial material that is largely lunar derived for lunar surface applications. The most effective driver for lunar industrialization may be the prospects for industrial space solar power systems in orbit or on the moon that are built with lunar materials. Such systems would require large quantities of electronic grade silicon or compound semiconductors for photovoltaics and electronic controls. Since silicon is the most abundant semimetal in the silicate portion of any solar system rock (approximately 20 wt percent), lunar silicon production is bound to be an important process in such a solar power project. The lunar silicon extraction process is discussed.

Ethyl Alcohol Extract of Hizikia fusiforme Induces Caspase ...

African Journals Online (AJOL)

Ethyl Alcohol Extract of Hizikia fusiforme Induces Caspase-dependent Apoptosis in Human Leukemia U937 Cells by Generation of Reactive Oxygen Species. C-H Kang, S-H Kang, S-H Boo, S-Y Park, D-O Moon, G-Y Kim ...

Liver damage caused by hepatitis C viral infection and ethyl alcohol consumption

Directory of Open Access Journals (Sweden)

Kostić Velimir

2006-01-01

Full Text Available Background/Aim. Hepatitis C virus infection (HCV is a complex disease, most commonly chronicle (80-85%. The aim of this research was to determinate the level of the liver damage in the patients cansed by HCV in conjunction with consuming ethyl alcohol. Methods. The research included 15 patients with chronic HCV infection supported by the misuse of ethyl alcohol, as well. The diagnosis of C infection hepatitis was proved using the ELISA test and PCR method. Results. The results of the study showed the liver damage by both HCV infection and ethyl alcohol, which was verified by the presence of biochemical changes and patohystological processing of the patients (liver biopsy and prosection. Patohystological changes were at the level of liver cirrhosis and carcinoma (2 patients. There was a signficant difference between the two subgroups (p < 0.001 regarding the examined values γ-GT, PLT and PTV. The basic therapeutic procedure was to introduce this category of patients into alcohol abstinence, and, in a few patients, to apply the antivirus therapy, as well. Conclusion. Based on the number of the examined patients (n = 15, we could conclude that a prolonged ethyl alcohol misuse with the presence of HCV infection was in a correlation with the liver disease progression.

Synthesis and Fungicidal activity of some sulphide derivatives of O-Ethyl-N-substituted phenylcarbamates

International Nuclear Information System (INIS)

Imeokparia, F.A.

2006-01-01

Monosulphides of O-ethyl-N-substituted phenylcarbamates were prepared by the reaction between O-ethyl-N-substituted phenylcarbamates and sulphur dichloride, while the corresponding disulphides were prepared by the reaction between O-ethyl-N-substituted phenylcarbamates and sulphur monochloride. The synthesized compounds were characterized by elemental analysis, thin layer chromatography (TLC), Fourier-transform infrared, and /sup 1/H and /sup 13/C nuclear magnetic resonance spectroscopic techniques. In vitro fungicidal assay of these sulphides against Fusarium oxysporum, Aspergillus niger, Aspergillus flavus and Rhizopus stolonifer showed that they had Greater fungicidal activity than their parent carbamates. The synthesized sulphides were more active towards A. Niger and A. flavus. Unlike the parent carbamates, the type of substituents attached to the aromatic nucleus of these sulphides had little or no effect on their fungicidal activity as there was insignificant variation in the fungicidal activity of the monosulphide and the disulphide derivatives of O-ethyl-N-substituted phenylcarbamates. (author)

Direct Conversion of Cellulose into Ethyl Lactate in Supercritical Ethanol-Water Solutions.

Science.gov (United States)

Yang, Lisha; Yang, Xiaokun; Tian, Elli; Lin, Hongfei

2016-01-08

Biomass-derived ethyl lactate is a green solvent with a growing market as the replacement for petroleum-derived toxic organic solvents. Here we report, for the first time, the production of ethyl lactate directly from cellulose with the mesoporous Zr-SBA-15 silicate catalyst in a supercritical mixture of ethanol and water. The relatively strong Lewis and weak Brønsted acid sites on the catalyst, as well as the surface hydrophobicity, were beneficial to the reaction and led to synergy during consecutive reactions, such as depolymerization, retro-aldol condensation, and esterification. Under the optimum reaction conditions, ∼33 % yield of ethyl lactate was produced from cellulose with the Zr-SBA-15 catalyst at 260 °C in supercritical 95:5 (w/w) ethanol/water. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Study of the rearrangement of N-alkylaniline to p-aminoalkylbencene. I. N-ethyl-l-14C-aniline

International Nuclear Information System (INIS)

Molera, M. J.; Gamboa, J. M.; Val Cob, M. del

1961-01-01

The rearrangement of N-ethylaniline to p-aminoethylbenzene has been studied over the temperature range 200-300 degree centigrade using different catalysts: Cl 2 Co, Cl 2 Zn, Cl 2 Ni, Cl 3 Al, Cl 2 Cd and Br H.N-ethyl-1- 1 4C-aniline has been synthesized from ethyl-1- 1 4C-iodide and aniline and its rearrangement to p-aminoethyl-benzene proves that the ethyl group does not rearrange itself during the reaction. A scheme for the degradation of both the N-ethyl-1- 1 4C aniline and the p-aminoethylbenzene produces is described. (Author) 14 refs

Development of a method based on on-line reversed phase liquid chromatography and gas chromatography coupled by means of an adsorption-desorption interface for the analysis of selected chiral volatile compounds in methyl jasmonate treated strawberries.

Science.gov (United States)

de la Peña Moreno, Fernando; Blanch, Gracia Patricia; Flores, Gema; Ruiz Del Castillo, Maria Luisa

2010-02-12

A method based on the use of the through oven transfer adsorption-desorption (TOTAD) interface in on-line coupling between reversed phase liquid chromatography and gas chromatography (RPLC-GC) for the determination of chiral volatile compounds was developed. In particular, the method was applied to the study of the influence of methyl jasmonate (MJ) treatment on the production and enantiomeric composition of selected aroma compounds in strawberry. The compounds studied were ethyl 2-methylbutanoate, linalool and 4-hydroxy-2,5-dimethyl-3(2H)-furanone (i.e. furaneol), which were examined on days 3, 6 and 9 after treatment. The method developed resulted in relative standard deviations (RSDs) of 21.6%, 8.1% and 9.8% and limits of detection (LD) of 0.04, 0.07 and 0.02mg/l for ethyl 2-methylbutanoate, linalool and furaneol, respectively. The application of the RPLC-TOTAD-GC method allowed higher levels of ethyl 2-methylbutanoate, linalool and furaneol to be detected, particularly after 9 days of treatment. Besides, MJ demonstrated to affect the enantiomeric distribution of ethyl 2-methylbutanoate. On the contrary, the enantiomeric composition of linalool and furaneol kept constant in both control and MJ-treated strawberries throughout the study. These results are discussed. Copyright 2009 Elsevier B.V. All rights reserved.

Production of ethyl alcohol from bananas

Energy Technology Data Exchange (ETDEWEB)

Jones, R.L.; Towns, T.

1983-12-01

The production of ethyl alcohol from waste bananas presents many special problems. During cooking, matting of the latex fibers from the banana peel recongeal when cooled and left untreated. This problem has been addressed by Alfaro by the use of CaC1/sub 2/. Separation of solids prior to distillation of the mashes in an economical fashion and use of the by product are also of concern to banana processors.

Ethyl cellulose microcapsules for protecting and controlled release of folic acid.

Science.gov (United States)

Prasertmanakit, Satit; Praphairaksit, Nalena; Chiangthong, Worawadee; Muangsin, Nongnuj

2009-01-01

Ethyl cellulose microcapsules were developed for use as a drug-delivery device for protecting folic acid from release and degradation in the undesirable environmental conditions of the stomach, whilst allowing its release in the intestinal tract to make it available for absorption. The controlled release folic acid-loaded ethyl cellulose microcapsules were prepared by oil-in-oil emulsion solvent evaporation using a mixed solvent system, consisting of a 9:1 (v/v) ratio of acetone:methanol and light liquid paraffin as the dispersed and continuous phase. Span 80 was used as the surfactant to stabilize the emulsion. Scanning electron microscopy revealed that the microcapsules had a spherical shape. However, the particulate properties and in vitro release profile depended on the concentrations of the ethyl cellulose, Span 80 emulsifier, sucrose (pore inducer), and folic acid. The average diameter of the microcapsules increased from 300 to 448 microm, whilst the folic acid release rate decreased from 52% to 40%, as the ethyl cellulose concentration was increased from 2.5% to 7.5% (w/v). Increasing the Span 80 concentration from 1% to 4% (v/v) decreased the average diameter of microcapsules from 300 to 141 microm and increased the folic acid release rate from 52% to 79%. The addition of 2.5-7.5% (w/v) of sucrose improved the folic acid release from the microcapsules. The entrapment efficiency was improved from 64% to 88% when the initial folic acid concentration was increased from 1 to 3 mg/ml.

Biofiltration of high loads of ethyl acetate in the presence of toluene.

Science.gov (United States)

Deshusses, M; Johnson, C T; Leson, G

1999-08-01

To date, biofilters have been used primarily to control dilute, usually odorous, off-gases with relatively low volatile organic compound (VOC) concentrations (elimination capacities for ethyl acetate were typically in the range of 200 g m-3 hr-1. Despite the presence of toluene degraders, the removal of toluene was inhibited by high loads of ethyl acetate. Several byproducts, particularly ethanol, were formed. Short-term dry-out and temperature excursions resulted in reduced performance.

Hydrogen-terminated mesoporous silicon monoliths with huge surface area as alternative Si-based visible light-active photocatalysts

KAUST Repository

Li, Ting

2016-07-21

Silicon-based nanostructures and their related composites have drawn tremendous research interest in solar energy storage and conversion. Mesoporous silicon with a huge surface area of 400-900 m2 g-1 developed by electrochemical etching exhibits excellent photocatalytic ability and stability after 10 cycles in degrading methyl orange under visible light irradiation, owing to its unique mesoporous network, abundant surface hydrides and efficient light harvesting. This work showcases the profound effects of surface area, crystallinity, pore topology on charge migration/recombination and mass transportation. Therein the ordered 1D channel array has outperformed the interconnected 3D porous network by greatly accelerating the mass diffusion and enhancing the accessibility of the active sites on the extensive surfaces. © 2016 The Royal Society of Chemistry.

Solvent exchange-induced in situ forming gel comprising ethyl cellulose-antimicrobial drugs.

Science.gov (United States)

Phaechamud, Thawatchai; Mahadlek, Jongjan

2015-10-15

Solvent-exchanged in situ forming gel is a drug delivery system which is in sol form before administration. When it contacts with the body fluid, then the water miscible organic solvent dissipates and water penetrates into the system, leading the polymer precipitation as in situ gel at the site of injection. The aim of this research was to study the parameters affecting the gel properties, drug release and antimicrobial activities of the in situ forming gels prepared from ethyl cellulose (EC) dissolved in N-methyl pyrrolidone (NMP) to deliver the antimicrobial agents (doxycycline hyclate, metronidazole and benzyl peroxide) for periodontitis treatment. The gel appearance, pH, viscosity, rheology, syringeability, gel formation, rate of water diffusion into the gels, in vitro degradation, drug release behavior and antimicrobial activities against Staphylococcus aureus, Escherichia coli, Candida albicans, Streptococcus mutans and Porphyrommonas gingivalis were determined. Increasing the amount of EC increased the viscosity of system while still exhibiting Newtonian flow and increased the work of syringeability whereas decreased the releasing of drug. The system transformed into the rigid gel formation after being injected into the simulated gingival crevicular fluid. The developed systems containing 5% w/w antimicrobial agent showed the antimicrobial activities against all test bacteria. Thus the developed solvent exchange-induced in situ forming gels comprising EC-antimicrobial drugs exhibited potential use for periodontitis treatment. Copyright © 2015 Elsevier B.V. All rights reserved.

Differential susceptibility of rats and guinea pigs to the ototoxic effects of ethyl benzene

NARCIS (Netherlands)

Cappaert, N.L.M.; Klis, S.F.L.; Muijser, H.; Kulig, B.M.; Ravensberg, L.C.; Smoorenburg, G.F.

2002-01-01

The present study was designed to compare the ototoxic effects of volatile ethyl benzene in guinea pigs and rats. Rats showed deteriorated auditory thresholds in the mid-frequency range, based on electrocochleography, after 550-ppm ethyl benzene (8 h/day, 5 days). Outer hair cell (OHC) loss was

Effect of Trinexapac-Ethyl and Traffic Stress on Physiological and Morphological Characteristics of Wheat Grass(Agropyron desertorum

Directory of Open Access Journals (Sweden)

M. H. Sheikh Mohamadi

2015-06-01

Full Text Available In order to evaluate the effect of trinexapac ethyl concentrations (0, 250 and 500 g/h and traffic stress (traffic and non traffic treatments on wheat grass physiological and morphological traits, an experiment was conducted on research farm of Isfahan University of Technology in 2011 - 2012 as factorial in completely randomized designs with three replications. The studied traits involved plant height and plant density, shoot dry weight and fresh weights, tillering, chlorophyll level, roots and shoot dissolved carbohydrates. Results showed that Trinexapac ethyl reduced plant height, fresh weight and dry weight of cut parts significantly. Application of 250 and 500 g/h Trinexapac ethyl decreased plant height by 21.23 percent and 31.85 percent respectively. Application of Trinexapac ethyl improved plant height, tillering and chlorophyll level. In contrast, chlorophyll level was decreased substantially under traffic treatment and this treatment did not affect wheat grass density and tillering significantly. Under 500 g/h Trinexapac ethyl treatment, tillering was increased by 36 percent compared with under control condition one. Results showed that Trinexapac ethyl application and traffic increased dissolved carbohydrates of root and shoot significantly. As a result, it was found that wheat grass is a traffic resistant plant and it seems that the use of Trinexapac ethyl increases plant resistance to traffic stress

Colloidal characterization of ultrafine silicon carbide and silicon nitride powders

Science.gov (United States)

Whitman, Pamela K.; Feke, Donald L.

1986-01-01

The effects of various powder treatment strategies on the colloid chemistry of aqueous dispersions of silicon carbide and silicon nitride are examined using a surface titration methodology. Pretreatments are used to differentiate between the true surface chemistry of the powders and artifacts resulting from exposure history. Silicon nitride powders require more extensive pretreatment to reveal consistent surface chemistry than do silicon carbide powders. As measured by titration, the degree of proton adsorption from the suspending fluid by pretreated silicon nitride and silicon carbide powders can both be made similar to that of silica.

Potential antipsychotic agents. 7. Synthesis and antidopaminergic properties of the atypical highly potent (S)-5-bromo-2,3-dimethoxy-N-[(1-ethyl-2-pyrrolidinyl)methyl]benzamide and related compounds. A comparative study.

Science.gov (United States)

Högberg, T; de Paulis, T; Johansson, L; Kumar, Y; Hall, H; Ogren, S O

1990-08-01

(S)-5-Bromo-2,3-dimethoxy-N-[(1-ethyl-2-pyrrolidinyl)methyl]benzamide (6) and some related compounds, i.e. the R isomer 7, the 3-hydroxy analogue 8, the desbromo derivative 9, the monomethoxy compound 10, and the 2,4-dimethoxy analogue 11, have been synthesized from the corresponding benzoic acids. The benzamides, lacking o-hydroxy groups, were evaluated for their affinity for the [3H]spiperone binding site and for their inhibition of apomorphine-induced behavioral responses in relation to the effect of the corresponding salicylamides. Besides the 2-hydroxy-3-methoxybenzamide 12 and the related 1,4-benzodioxane (13) and 2,3-dihydrobenzofuran (14), carboxamides were investigated in order to evaluate the stereoelectronic requirements on the 2-methoxy group for the receptor interaction. The study supports the view that the o-methoxy group may adopt coplanar, as well as perpendicular orientations, and maintain the intramolecular hydrogen bonding required in the bioactive conformation. The benzamide 6 was found to be equipotent with the analogous highly active salicylamide 3 (FLB 463) both in vitro and in vivo. In addition, 6 displayed a preferential inhibition of the hyperactivity component of the behavioral syndrome, which is regarded to indicate a low tendency to induce extrapyramidal side effects in man at antipsychotically effective doses. The benzamide class of compounds (6-10) were found to be somewhat more sensitive to the structural modifications than the salicylamide class, i.e. the o-hydroxy-substituted benzamides (2-5). The potent and selective benzamide 6 (FLB 457) is highly suitable for investigations of dopamine D-2 mediated responses and, in radiolabeled form, for receptor binding studies in vitro and in vivo.

A Rat Model for Human Ductal Carcinoma In Situ

Science.gov (United States)

2006-09-01

nitrosourea (MNU). The cancers were varied in their estrogen and progesterone receptor expression as determined by immunocytochemistry. The objectives...transformed to preneoplastic and neoplastic states with well known mammary carcinogens such as N-methyl-N- nitrosourea (4), N-ethyl- nitrosourea ...methyl-N- nitrosourea or N-ethyl- nitrosourea . Our experimental objectives were to develop methods for the induction of intraductal and intralobular

Synthesis of enantiomerically pure (R)- and (S)-2-sulfanylpropanoic acids (‘thiolactic acid’) from ethyl (S)-lactate using pig liver esterase

NARCIS (Netherlands)

Hof, Robert P.; Kellogg, Richard M.

1995-01-01

The methanesulfonates of optically pure ethyl (S)-lactate or ethyl (R)-2-chloropropanoate 5, obtained with inversion of configuration from ethyl (S)-lactate on treatment with SOCl2, can be substituted by caesium thiolates with inversion of configuration to yield (R) and (S) ethyl

Novel N-benzoyltyramines of Swinglea glutinosa (Rutaceae); Novas N-benzoiltiraminas de Swinglea glutinosa (Rutaceae).

Energy Technology Data Exchange (ETDEWEB)

Cerqueira, Cristovam do Nascimento; Santos, Djalma A.P. dos; Malaquias, Karla da Silva; Lima, Murilo Marinho de Castro; Silva, Maria Fatima das Gracas Fernandes da; Fernandes, Joao Batista; Vieira, Paulo Cezar, E-mail: dmfs@ufscar.br [Universidade Federal de Sao Carlos (UFSCAR), SP (Brazil). Dept. de Quimica

2012-07-01

Phytochemical studies of the leaves and fruits have led to the identification of the known amides (E)-N-methyl-cinnamamide, N-benzoyltyramine, N-benzoyl-O-geranyl tyramine, N-benzoyl-O-(4-acetoxyl)-geranyl tyramine, in addition to the new N-{l_brace}2-[4-(butoxyl-3-one)phenyl]ethyl{r_brace}benzamide, N-{l_brace}2-[4-(2,3-dihydroxy-2-methyl-butoxylanal)phenyl]ethyl{r_brace}benzamide, N-{l_brace}2-[4-(2,3-dihydroxy-2-methyl-butoxyloic) phenyl]ethyl{r_brace}benzamide, N-benzoyl-O-(4-acetoxyl-6,7-epoxy)-geranyltyramine, N-benzoyl-O-(4-acetoxyl-6,7-dihydroxy)-geranyltyramine and N-benzoyl-O-(6-acetoxyl-4,7-dihydroxy)-geranyltyramine. The isolated compounds clearly point to Swinglea phytochemical affinities with other Aurantioideae species. (author)

UV absorption and photoisomerization of p-methoxycinnamate grafted silicone.

Science.gov (United States)

Pattanaargson, Supason; Hongchinnagorn, Nantawan; Hirunsupachot, Piyawan; Sritana-anant, Yongsak

2004-01-01

p-Methoxycinnamate moieties, UV-B-absorptive chromophores of the widely used UV-B filter, 2-ethylhexyl p-methoxycinnamate (OMC), were grafted onto the 7 mol% amino functionalized silicone polymer through amide linkages. Comparing with OMC, the resulting poly [3-(p-methoxycinnamido)(propyl)(methyl)-dimethyl] siloxane copolymer (CAS) showed less E to Z isomerization when exposed to UV-B light. The absorption profiles of the product showed the maximum absorption wavelength to be similar to that of OMC but with less sensitivity to the type of solvent. Poly (methylhydrosiloxane) grafted with 10 mol% p-methoxycinnamoyl moieties was prepared through hydrosilylations of 2-propenyl-p-methoxycinnamate, in which the resulting copolymer showed similar results to those of CAS.

Phase equilibrium measurements and thermodynamic modelling for the system (CO2 + ethyl palmitate + ethanol) at high pressures

International Nuclear Information System (INIS)

Gaschi, Priscilla S.; Mafra, Marcos R.; Ndiaye, Papa M.; Corazza, Marcos L.

2013-01-01

Graphical abstract: Ethyl palmitate and biodiesel comparison in a pressure–composition diagram for the systems (CO 2 + ethyl palmitate + biodiesel), at different temperatures. Highlights: ► We measured VLE, LLE, and VLLE for the system (CO 2 + ethyl palmitate + ethanol). ► The saturation pressures were obtained using a variable-volume view cell. ► Phase envelope of (CO 2 + ethyl palmitate) is different that (CO 2 + soybean oil biodiesel). ► The experimental data were modeled using PR-vdW2 and PR–WS equations of state. - Abstract: This work reports phase equilibrium measurements for the binary {CO 2 (1) + ethyl palmitate(2)} and ternary {CO 2 (1) + ethyl palmitate(2) + ethanol(3)} systems at high pressures. There is currently great interest in biodiesel production processes involving supercritical and/or pressurized solvents, such as non-catalytic supercritical biodiesel production and enzyme-catalysed biodiesel production. Also, supercritical CO 2 can offer an interesting alternative for glycerol separation in the biodiesel purification step in a water-free process. In this context, the main goal of this work was to investigate the phase behaviour of binary and ternary systems involving CO 2 , a pure constituent of biodiesel ethyl palmitate and ethanol. Experiments were carried out in a high-pressure variable-volume view cell with operating temperatures ranging from (303.15 to 353.15) K and pressures up to 21 MPa. The CO 2 mole fraction ranged from 0.5033 to 0.9913 for the binary {CO 2 (1) + ethyl palmitate(2)} system and from 0.4436 to 0.9712 for ternary system {CO 2 (1) + ethyl palmitate(2) + ethanol(3)} system with ethyl ester to ethanol molar ratios of (1:6), (1:3), and (1:1). For the systems investigated, vapour–liquid (VL), liquid–liquid (LL) and vapour–liquid–liquid (VLL) phase transitions were observed. The experimental data sets were successfully modeled using the Peng–Robinson equation of state with the classical van der Waals

Electrochemical lithiation of thin silicon based layers potentiostatically deposited from ionic liquid

International Nuclear Information System (INIS)

Vlaic, Codruta Aurelia; Ivanov, Svetlozar; Peipmann, Ralf; Eisenhardt, Anja; Himmerlich, Marcel; Krischok, Stefan; Bund, Andreas

2015-01-01

Thin silicon layers containing about 20% carbon and 20% oxygen were deposited on copper substrates by potentiostatic electroreduction from a 1 M SiCl 4 1-butyl-1-methyl-pyrrolidinium bis (trifluoromethyl) sulfonylimide [BMP][TFSI] electrolyte. The electrodeposition process was investigated by means of voltammetric techniques, coupled with in-situ microgravimetry (quartz crystal microbalance, QCM). The electrochemical and QCM data suggest a possible contribution of a partial Si 4+ to Si 2+ reduction and/or a restructuring of the metallic substrate. Considerable impact of side reactions parallel to the deposition process was indicated by QCM measurements performed under potentiostatic and potentiodynamic conditions. The deposition of silicon-based films was confirmed by energy dispersive X-ray analysis (EDX). Analysis of the chemical composition of the deposit and its elemental distribution were achieved by depth profiling X-ray photoelectron spectroscopy (XPS). The electrodeposited silicon containing layers showed stable lithiation and delithiation with capacity values of about 1200 mAhg −1 and 80% capacity retention after 300 cycles in standard EC/DMC electrolytes. In ionic liquid (IL) the material displayed lower capacity of ca. 500 mAhg −1 , which can be attributed to the higher viscosity of this electrolyte and deposition of IL decomposition products during lithiation

Colorimetric determination of uranium using ammonium thiocyanate in a medium of ethyl acetate, acetone and water; Dosage colorimetrique de l'uranium par le thiocyanate d'ammonium en milieu acetate d'ethyle-acetone-eau

Energy Technology Data Exchange (ETDEWEB)

Hucleux, M; Dessapt, P

1959-04-01

The method consists of colorimetrically analyzing uranium using ammonium sulfo-cyanide in the solvent phase. The optimum conditions for extracting uranium by ethyl acetate have been studied. A precise colorimetric method was established which depends on the extracted phase and on the behavior of the ethyl acetate-acetone medium. (author) [French] La methode consiste a doser l'uranium par colorimetrie au sulfocyanure d'ammonium en phase solvant. Les meilleures conditions d'extraction de l'uranium par l'acetate d'ethyle ont ete etudiees. Une colorimetrie precise a ete mise au point en fonction de l'acidite de la phase extraite et du comportement du milieu acetate d'ethyleacetone. (auteur)

Ethyl 4-chloro-2′-fluoro-3-hydroxy-5-methylbiphenyl-2-carboxylate

Directory of Open Access Journals (Sweden)

Muhammad Adeel

2011-09-01

Full Text Available In the title compound, C16H14ClFO3, the dihedral angle between the mean planes of the two benzene rings is 71.50 (5°. Due to an intramolecular O—H...O hydrogen bond between the hydroxy group and the carbonyl O atom of the ethyl ester group, the ethyl ester group lies within the ring plane. The crystal structure is consolidated by intermolecular C—H...O and C—H...F interactions.

DNA methylation analysis reveals distinct methylation signatures in pediatric germ cell tumors

International Nuclear Information System (INIS)

Amatruda, James F; Frazier, A Lindsay; Poynter, Jenny N; Ross, Julie A; Christensen, Brock; Fustino, Nicholas J; Chen, Kenneth S; Hooten, Anthony J; Nelson, Heather; Kuriger, Jacquelyn K; Rakheja, Dinesh

2013-01-01

Aberrant DNA methylation is a prominent feature of many cancers, and may be especially relevant in germ cell tumors (GCTs) due to the extensive epigenetic reprogramming that occurs in the germ line during normal development. We used the Illumina GoldenGate Cancer Methylation Panel to compare DNA methylation in the three main histologic subtypes of pediatric GCTs (germinoma, teratoma and yolk sac tumor (YST); N = 51) and used recursively partitioned mixture models (RPMM) to test associations between methylation pattern and tumor and demographic characteristics. We identified genes and pathways that were differentially methylated using generalized linear models and Ingenuity Pathway Analysis. We also measured global DNA methylation at LINE1 elements and evaluated methylation at selected imprinted loci using pyrosequencing. Methylation patterns differed by tumor histology, with 18/19 YSTs forming a distinct methylation class. Four pathways showed significant enrichment for YSTs, including a human embryonic stem cell pluripotency pathway. We identified 190 CpG loci with significant methylation differences in mature and immature teratomas (q < 0.05), including a number of CpGs in stem cell and pluripotency-related pathways. Both YST and germinoma showed significantly lower methylation at LINE1 elements compared with normal adjacent tissue while there was no difference between teratoma (mature and immature) and normal tissue. DNA methylation at imprinted loci differed significantly by tumor histology and location. Understanding methylation patterns may identify the developmental stage at which the GCT arose and the at-risk period when environmental exposures could be most harmful. Further, identification of relevant genetic pathways could lead to the development of new targets for therapy

Arsenic implantation into polycrystalline silicon and diffusion to silicon substrate

International Nuclear Information System (INIS)

Tsukamoto, K.; Akasaka, Y.; Horie, K.

1977-01-01

Arsenic implantation into polycrystalline silicon and drive-in diffusion to silicon substrate have been investigated by MeV He + backscattering analysis and also by electrical measurements. The range distributions of arsenic implanted into polycrystalline silicon are well fitted to Gaussian distributions over the energy range 60--350 keV. The measured values of R/sub P/ and ΔR/sub P/ are about 10 and 20% larger than the theoretical predictions, respectively. The effective diffusion coefficient of arsenic implanted into polycrystalline silicon is expressed as D=0.63 exp[(-3.22 eV/kT)] and is independent of the arsenic concentration. The drive-in diffusion of arsenic from the implanted polycrystalline silicon layer into the silicon substrate is significantly affected by the diffusion atmosphere. In the N 2 atmosphere, a considerable amount of arsenic atoms diffuses outward to the ambient. The outdiffusion can be suppressed by encapsulation with Si 3 N 4 . In the oxidizing atmosphere, arsenic atoms are driven inward by growing SiO 2 due to the segregation between SiO 2 and polycrystalline silicon, and consequently the drive-in diffusion of arsenic is enhanced. At the interface between the polycrystalline silicon layer and the silicon substrate, arsenic atoms are likely to segregate at the polycrystalline silicon side

Porous silicon: silicon quantum dots for photonic applications

International Nuclear Information System (INIS)

Pavesi, L.; Guardini, R.

1996-01-01

Porous silicon formation and structure characterization are briefly illustrated. Its luminescence properties rae presented and interpreted on the basis of exciton recombination in quantum dot structures: the trap-controlled hopping mechanism is used to describe the recombination dynamics. Porous silicon application to photonic devices is considered: porous silicon multilayer in general, and micro cavities in particular are described. The present situation in the realization of porous silicon LEDs is considered, and future developments in this field of research are suggested. (author). 30 refs., 30 figs., 13 tabs

Pharmacokinetics and pharmacodynamics of LGD-3303 [9-chloro-2-ethyl-1-methyl-3-(2,2,2-trifluoroethyl)-3H-pyrrolo-[3,2-f]quinolin-7(6H)-one], an orally available nonsteroidal-selective androgen receptor modulator.

Science.gov (United States)

Vajda, Eric G; López, Francisco J; Rix, Peter; Hill, Robert; Chen, Yanling; Lee, Kyoung-Jin; O'Brien, Z; Chang, William Y; Meglasson, Martin D; Lee, Yong-Hee

2009-02-01

Selective androgen receptor modulators (SARMs) are a new class of molecules in development to treat a variety of diseases. SARMs maintain the beneficial effects of androgens, including increased muscle mass and bone density, while having reduced activity on unwanted side effects. The mechanisms responsible for the tissue-selective activity of SARMs are not fully understood, and the pharmacokinetic (PK)/pharmacodynamic (PD) relationships are poorly described. Tissue-specific compound distribution potentially could be a mechanism responsible for apparent tissue selectivity. We examined the PK/PD relationship of a novel SARM, LGD-3303 [9-chloro-2-ethyl-1-methyl-3-(2,2,2-trifluoroethyl)-3H-pyrrolo[3,2-f]quinolin-7(6H)-one], in a castrated rat model of androgen deficiency. LGD-3303 has potent activity on levator ani muscle but is a partial agonist on the preputial gland and ventral prostate. LGD-3303 never stimulated ventral prostate above intact levels despite increasing plasma concentrations of compound. Tissue-selective activity was maintained when LGD-3303 was dosed orally or by continuous infusion, two routes of administration with markedly different time versus exposure profiles. Despite the greater muscle activity relative to prostate activity, local tissue concentrations of LGD-3303 were higher in the prostate than in the levator ani muscle. LGD-3303 has SARM properties that are independent of its pharmacokinetic profile, suggesting that the principle mechanism for tissue-selective activity is the result of altered molecular interactions at the level of the androgen receptor.

Modeling of the oxidation of methyl esters—Validation for methyl hexanoate, methyl heptanoate, and methyl decanoate in a jet-stirred reactor

Science.gov (United States)

Glaude, Pierre Alexandre; Herbinet, Olivier; Bax, Sarah; Biet, Joffrey; Warth, Valérie; Battin-Leclerc, Frédérique

2013-01-01

The modeling of the oxidation of methyl esters was investigated and the specific chemistry, which is due to the presence of the ester group in this class of molecules, is described. New reactions and rate parameters were defined and included in the software EXGAS for the automatic generation of kinetic mechanisms. Models generated with EXGAS were successfully validated against data from the literature (oxidation of methyl hexanoate and methyl heptanoate in a jet-stirred reactor) and a new set of experimental results for methyl decanoate. The oxidation of this last species was investigated in a jet-stirred reactor at temperatures from 500 to 1100 K, including the negative temperature coefficient region, under stoichiometric conditions, at a pressure of 1.06 bar and for a residence time of 1.5 s: more than 30 reaction products, including olefins, unsaturated esters, and cyclic ethers, were quantified and successfully simulated. Flow rate analysis showed that reactions pathways for the oxidation of methyl esters in the low-temperature range are similar to that of alkanes. PMID:23710076

Modeling of the oxidation of methyl esters-Validation for methyl hexanoate, methyl heptanoate, and methyl decanoate in a jet-stirred reactor.

Science.gov (United States)

Glaude, Pierre Alexandre; Herbinet, Olivier; Bax, Sarah; Biet, Joffrey; Warth, Valérie; Battin-Leclerc, Frédérique

2010-11-01

The modeling of the oxidation of methyl esters was investigated and the specific chemistry, which is due to the presence of the ester group in this class of molecules, is described. New reactions and rate parameters were defined and included in the software EXGAS for the automatic generation of kinetic mechanisms. Models generated with EXGAS were successfully validated against data from the literature (oxidation of methyl hexanoate and methyl heptanoate in a jet-stirred reactor) and a new set of experimental results for methyl decanoate. The oxidation of this last species was investigated in a jet-stirred reactor at temperatures from 500 to 1100 K, including the negative temperature coefficient region, under stoichiometric conditions, at a pressure of 1.06 bar and for a residence time of 1.5 s: more than 30 reaction products, including olefins, unsaturated esters, and cyclic ethers, were quantified and successfully simulated. Flow rate analysis showed that reactions pathways for the oxidation of methyl esters in the low-temperature range are similar to that of alkanes.

Micellar phase boundaries under the influence of ethyl alcohol

International Nuclear Information System (INIS)

Bergeron, Denis E.

2016-01-01

The Compton spectrum quenching technique is used to monitor the effect of ethyl alcohol (EtOH) additions on phase boundaries in two systems. In toluenic solutions of the nonionic surfactant, Triton X-100, EtOH shifts the boundary separating the first clear phase from the first turbid phase to higher water:surfactant ratios. In a commonly used scintillant, Ultima Gold AB, the critical micelle concentration is not shifted. The molecular interactions behind the observations and implications for liquid scintillation counting are discussed. - Highlights: • Compton spectrum quenching technique applied to find micellar phase boundaries. • Toluenic Triton X-100 and Ultima Gold AB investigated. • Ethyl alcohol affects phase boundaries in Triton X-100, not in Ultima Gold AB. • Phase boundary observations discussed in terms of relevant molecular interactions.

Silicon-Rich Silicon Carbide Hole-Selective Rear Contacts for Crystalline-Silicon-Based Solar Cells.

Science.gov (United States)

Nogay, Gizem; Stuckelberger, Josua; Wyss, Philippe; Jeangros, Quentin; Allebé, Christophe; Niquille, Xavier; Debrot, Fabien; Despeisse, Matthieu; Haug, Franz-Josef; Löper, Philipp; Ballif, Christophe

2016-12-28

The use of passivating contacts compatible with typical homojunction thermal processes is one of the most promising approaches to realizing high-efficiency silicon solar cells. In this work, we investigate an alternative rear-passivating contact targeting facile implementation to industrial p-type solar cells. The contact structure consists of a chemically grown thin silicon oxide layer, which is capped with a boron-doped silicon-rich silicon carbide [SiC x (p)] layer and then annealed at 800-900 °C. Transmission electron microscopy reveals that the thin chemical oxide layer disappears upon thermal annealing up to 900 °C, leading to degraded surface passivation. We interpret this in terms of a chemical reaction between carbon atoms in the SiC x (p) layer and the adjacent chemical oxide layer. To prevent this reaction, an intrinsic silicon interlayer was introduced between the chemical oxide and the SiC x (p) layer. We show that this intrinsic silicon interlayer is beneficial for surface passivation. Optimized passivation is obtained with a 10-nm-thick intrinsic silicon interlayer, yielding an emitter saturation current density of 17 fA cm -2 on p-type wafers, which translates into an implied open-circuit voltage of 708 mV. The potential of the developed contact at the rear side is further investigated by realizing a proof-of-concept hybrid solar cell, featuring a heterojunction front-side contact made of intrinsic amorphous silicon and phosphorus-doped amorphous silicon. Even though the presented cells are limited by front-side reflection and front-side parasitic absorption, the obtained cell with a V oc of 694.7 mV, a FF of 79.1%, and an efficiency of 20.44% demonstrates the potential of the p + /p-wafer full-side-passivated rear-side scheme shown here.

The bioactive compounds and antioxidant activity of ethanol and ethyl ecetate extracts of Candi Banana (Musa paradisiaca)

Science.gov (United States)

Laeliocattleya, R. A.; Estiasih, T.; Griselda, G.; Muchlisyiyah, J.

2018-03-01

Banana has various benefits for health. One local variety of banana is candi banana (Musa paradisiaca). The aim of this research was to study the content of the bioactive compounds of phenolics, flavonoids, tannin, carotenoids and the antioxidant activity of extract ethanol and ethyl acetate of candi banana. Powdered candi banana was extracted using ethanol and ethyl acetate in an ultrasonic bath. The results showed that the content of phenolics, flavonoids, tannin and carotenoids in ethanol extract were 58.76 ± 3.19 mg/kg, 416.08 ± 18.79 mg/kg, 209.83 ± 15.87 mg/kg and 74.55 ± 4.31 mg/kg, respectively. The content of phenolics, flavonoids, tannin and carotenoids in ethyl acetate extract were 0.83 ± 0.12 mg/kg, 4.31 ± 0.66 mg/kg, 49.97 ± 2.43 mg/kg and 304.40 ± 16.62 mg/kg. While the antioxidant activity (IC50) of ethanol extract and ethyl acetate were 3374.13 ± 123.46 ppm and 40318.19 ± 1014.90 ppm. This research showed that type of solvents of ethanol and ethyl acetate affected the content of bioactive compounds and antioxidant activity of candi banana. The antioxidant activity of ethanol extract was higher than that of ethyl acetate extract. It showed that ethanol was a better solvent than ethyl acetate to extract bioactive compounds in candi banana.

21 CFR 181.30 - Substances used in the manufacture of paper and paperboard products used in food packaging.

Science.gov (United States)

2010-04-01

... cyanodithioimidocarbamate with ethylene diamine and potassium N-methyl dithiocarbamate and/or sodium 2-mercaptobenzothiazole (slimicides).* Ethyl acrylate and methyl methacrylate copolymers of itaconic acid or methacrylic acid for use... acid (polymerized). Melamine formaldehyde polymer. Methyl acrylate (polymerized). Methyl ethers of mono...

Styrene and methyl methacrylate copolymer synthesized by RF inductively coupled plasma

Energy Technology Data Exchange (ETDEWEB)

Li, Z; Gillon, X; Diallo, M; Houssiau, L; Pireaux, J-J, E-mail: zhiling.li@fundp.ac.be [University of Namur (FUNDP) Research Centre in Physics of Matter and Radiation (PMR), 61, Rue de Bruxelles, 5000 Namur (Belgium)

2011-01-01

A series of random copolymers of styrene and methyl methacrylate was prepared on a silicon substrate by RF pulsed inductively coupled plasma. The plasma gas phase was investigated by optical emission spectroscopy (OES). The physico-chemical characteristics of the deposited copolymer films were analyzed by several surface techniques: X-ray photoelectron spectroscopy (XPS), Fourier-Transform infrared absorption (FT-IR), Time-of-flight secondary ion mass spectrometry (ToF-SIMS), etc. OES of the plasma and FT-IR spectra of the films are predictive: plasma emitting a higher relative benzyl radical signal results in the deposition of a more aromatic plasma polymer. The functional thin films can be deposited by selection of the co-monomers.

Antiplasmodial Properties and Bioassay-Guided Fractionation of Ethyl Acetate Extracts from Carica papaya Leaves

Science.gov (United States)

Melariri, Paula; Campbell, William; Etusim, Paschal; Smith, Peter

2011-01-01

We investigated the antiplasmodial properties of crude extracts from Carica papaya leaves to trace the activity through bioassay-guided fractionation. The greatest antiplasmodial activity was observed in the ethyl acetate crude extract. C. papaya showed a high selectivity for P. falciparum against CHO cells with a selectivity index of 249.25 and 185.37 in the chloroquine-sensitive D10 and chloroquine-resistant DD2 strains, respectively. Carica papaya ethyl acetate extract was subjected to bioassay-guided fractionation to ascertain the most active fraction, which was purified and identified using high-pressure liquid chromatography (HPLC) and GC-MS (Gas chromatography-Mass spectrometry) methods. Linoleic and linolenic acids identified from the ethyl acetate fraction showed IC50 of 6.88 μg/ml and 3.58 μg/ml, respectively. The study demonstrated greater antiplasmodial activity of the crude ethyl acetate extract of Carica papaya leaves with an IC50 of 2.96 ± 0.14 μg/ml when compared to the activity of the fractions and isolated compounds. PMID:22174990

Molecular aggregation states of poly{l_brace}2-(perfluorooctyl)ethyl acrylate{r_brace} polymer brush thin film analyzed by grazing incidence X-ray diffraction

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, H; Honda, K; Takahara, A [Graduate School of Engineering, Kyushu University, Nishi-ku, Fukuoka 819-0395 (Japan); Kobayashi, M [Institute for Materials Chemistry and Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka 819-0395 (Japan); Morita, M [Fundamental Research Department, Chemical Division, Daikin Industries, Ltd., 1-1 Nishi Hitotsuya, Settsu-shi, Osaka 566-8585 (Japan); Masunaga, H; Sasaki, S; Takata, M [Japan Synchrotron Research Institute, Mikazuki Sayo, Hyogo 671-5198 (Japan); Sakata, O, E-mail: takahara@cstf.kyushu-u.ac.j [RIKEN Harima Institute, Mikazuki Sayo, Hyogo 671-5198 (Japan)

2009-08-01

Fluoropolymer brush with crystalline side chains was prepared by surface-initiated atom transfer radical polymerization of 2-(perfluorooctyl)ethyl acrylate (FA-C{sub 8}) from a flat silicon substrate. The crystallization and the molecular aggregation structures of polymer side chain at the outermost surface and internal region in the brush film were characterized by grazing incidence X-ray diffraction (GIXD) measurement using two different incident angles of X-ray. At the air interface of PFA-C{sub 8} brush film, the rod-like R{sub f} group was oriented perpendicular to the surface forming a hexagonal packing structure to reduce surface energy. In contrast, the oriented R{sub f} groups parallel to the substrate coexisted at the internal region in the brush. This unique depth dependence of crystalline state of the fluoropolymer brush was observed by surface-sensitive GIXD measurement.

Separation and Analysis of Microwave-assisted Liquefied Products of Corn Stover

Directory of Open Access Journals (Sweden)

Weihua Xiao

2014-10-01

Full Text Available Corn stover was successfully liquefied by microwave heating at 160 °C with ethylene glycol (EG used as the solvent and sulfuric acid as a catalyst. Gas chromatography and mass spectrometry (GC-MS data indicated that methyl esters, including 3-(2-methyl-1,3-doxolane-2-yl propionic acid methyl ester (PAME, levulinic acid isopropyl ester (LAE, methyl laurate, and methyl palmitate were the major degradation compounds, in addition to EG derivatives in the liquefied product of corn stover (LPCS. For high value-added utilization of LPCS, solvent extraction was applied to characterize the components and to separate it into useful fractions. After being dispersed in water, the water-soluble fraction of the LPCS was then extracted with organic solvents, including hexane, chloroform, diethyl ether, and ethyl acetate. Levulinic acid isopropyl ester showed the highest distribution in chloroform and ethyl acetate, while the lowest in hexane and ether. Levulinic acid isopropyl ester was selectively enriched to 28.76% and 43.65% by sequential extraction with chloroform and ethyl acetate, respectively, in accordance with the quantitative analysis.

DNA damage induced in mouse peritoneal exudate cells after in vivo administration of chemical and physical agents as determined by alkaline elution

International Nuclear Information System (INIS)

Nishi, Yoshisuke; Miyanaga, Kumiko; Sato, Sei-ichi; Inui, Naomichi

1990-01-01

The alkaline elution technique for detecting DNA strand breaks has been applied to the study of DNA damage in mouse peritoneal exudate cells resulting from the in vivo administration of chemical and physical agents. The direct methylating agents methyl methanesulphonate and N-methyl-N-nitrosourea induced extensive breakage in samples taken 2 h after administration. The direct ethylating agents ethyl methanesulphonate and N-ethyl-N-nitrosourea also induced DNA strand breaks, but to a lesser extent than the methylating agents. The indirect methylating agent dimethylnitrosamine showed hardly any effect in this system. A weak but positive response was observed upon treatment with the anti-neoplastic alkylating agent procarbazine hydrochloride. The whole-body irradiation of mice with 60 Co γ-rays also induced DNA strand breaks. The elution profiles for γ-ray irradiation were different from those of alkylating agents, and indicate that alkylating agents produce many more secondary lesions leading to DNA strand breaks than γ-rays. N-methyl-N-nitrosourea produced slightly more DNA strand breaks in mutagen-sensitive mice, which are derived from the CD-1 strain, than in ICR mice. (Author)

DNA damage induced in mouse peritoneal exudate cells after in vivo administration of chemical and physical agents as determined by alkaline elution

Energy Technology Data Exchange (ETDEWEB)

Nishi, Yoshisuke (Japan Tobacco Inc., Yokohama (Japan). Central Research Inst.); Miyanaga, Kumiko; Sato, Sei-ichi (Japan Tobacco Inc., Hatano, Kanagawa (Japan). Toxicology Research Lab.); Inui, Naomichi (Japan Tobacco Inc., Yokohama, Kanagawa (Japan). Pharmaceutical Research Labs.)

1990-01-01

The alkaline elution technique for detecting DNA strand breaks has been applied to the study of DNA damage in mouse peritoneal exudate cells resulting from the in vivo administration of chemical and physical agents. The direct methylating agents methyl methanesulphonate and N-methyl-N-nitrosourea induced extensive breakage in samples taken 2 h after administration. The direct ethylating agents ethyl methanesulphonate and N-ethyl-N-nitrosourea also induced DNA strand breaks, but to a lesser extent than the methylating agents. The indirect methylating agent dimethylnitrosamine showed hardly any effect in this system. A weak but positive response was observed upon treatment with the anti-neoplastic alkylating agent procarbazine hydrochloride. The whole-body irradiation of mice with {sup 60}Co {gamma}-rays also induced DNA strand breaks. The elution profiles for {gamma}-ray irradiation were different from those of alkylating agents, and indicate that alkylating agents produce many more secondary lesions leading to DNA strand breaks than {gamma}-rays. N-methyl-N-nitrosourea produced slightly more DNA strand breaks in mutagen-sensitive mice, which are derived from the CD-1 strain, than in ICR mice. (Author).

(Z-Ethyl 3-(4-chlorophenyl-2-cyano-3-(2,6-difluorobenzamidoacrylate

Directory of Open Access Journals (Sweden)

Zhang Xiaoyan

2008-12-01

Full Text Available The title compound, C19H13ClF2N2O3, was prepared by the reaction of (Z-ethyl 3-amino-3-(4-chlorophenyl-2-cyanoacrylate and 2,6-difluorobenzoyl chloride. The dihedral angle between the chlorobenzene and fluorobenzene rings is 37.0 (1°. The ethyl group is disordered over two positions [occupancies = 0.52 (2:0.48 (2]. In addition to intramolecular N—H...O and N—H...F hydrogen bonds, the crystal packing shows the molecules to be connected by intermolecular C—H...O and C—H...N hydrogen bonds.

Biodegradation of ethyl acetate in radioactive liquid organic waste by bacterial communities

International Nuclear Information System (INIS)

Ferreira, Rafael V.P.; Sakata, Solange K.; Borba, Tania R.; Bellini, Maria H.; Marumo, Julio T.; Dutra, Fernando

2009-01-01

The research and development program in reprocessing of low burn-up spent fuel elements began in Brazil in 70's, originating the lab -scale hot cell, known as CELESTE located at IPEN-CNEN/SP. The program was ended at the beginning of 90's and part of the radioactive waste generated mainly from the analytical laboratories is stored at the Waste Management Laboratory. Among various types of radioactive waste generated, the organic liquid represents a major problem for its management, because it can not be directly solidified with cement. The objective of this work is to develop a pretreatment methodology to degrade the ethyl acetate present in organic liquid waste so that it can subsequently be immobilized in cement. This work was divided into two parts: selection and adaptation of three bacterial communities for growth in medium containing ethyl acetate and degradation experiments of ethyl acetate present in radioactive organic liquid waste. The results showed that from bacterial communities the highest biodegradation level observed was 77%. (author)

short communication reaction of ethyl acetoacetate and 2

African Journals Online (AJOL)

Preferred Customer

starting materials. Thus, we describe in this paper a facile procedure for the synthesis of 9- phenyl-6H-benzo[c]chromen-6-ones involving the reaction of ethyl acetoacetate and chalcones derived from the condensation of salicylaldehyde and acetophenone derivatives. RESULTS AND DISCUSSIONS. The conditions for the ...

Thermodynamic properties of alkyl 1H-indole carboxylate derivatives: A combined experimental and computational study

International Nuclear Information System (INIS)

Carvalho, Tânia M.T.; Amaral, Luísa M.P.F.; Morais, Victor M.F.; Ribeiro da Silva, Maria D.M.C.

2016-01-01

Highlights: • Combustion of methyl 1H-indole-3-carboxylate and ethyl 1H-indole-2-carboxylate by static bomb calorimetry. • The Knudsen mass-loss effusion technique was used to measure the vapour pressures of compounds at different temperatures. • Enthalpies of sublimation of methyl 1H-indole-3-carboxylate and ethyl 1H-indole-2-carboxylate. • Gas-phase enthalpies of formation of methyl 1H-indole-3-carboxylate and ethyl 1H-indole-2-carboxylate have been derived. • Gas-phase enthalpies of formation estimated from G3(MP2) calculations. - Abstract: The standard (p"o = 0.1 MPa) molar enthalpies of formation, in the crystalline phase, of methyl 1H-indole-3-carboxylate and ethyl 1H-indole-2-carboxylate, at T = 298.15 K, were derived from measurements of the standard massic energies of combustion using a static bomb combustion calorimeter. The Knudsen effusion technique was used to measure the vapour pressures as a function of the temperature, which allowed determining the standard molar enthalpies of sublimation of these compounds. The standard (p"o = 0.1 MPa) molar enthalpies of formation, in the gaseous phase, at T = 298.15 K, were calculated by combining, for each compound, the standard molar enthalpy of formation, in the crystalline phase, and the standard molar enthalpy of sublimation, yielding −(207.6 ± 3.6) kJ·mol"−"1 and −(234.4 ± 2.4) kJ·mol"−"1, for methyl 1H-indole-3-carboxylate and ethyl 1H-indole-2-carboxylate, respectively. Quantum chemical studies were also conducted, in order to complement the experimental study. The gas-phase enthalpies of formation were estimated from high level ab initio molecular orbital calculations, at the G3(MP2) level, for the compounds studied experimentally, extending the study to the methyl 1H-indole-2-carboxylate and ethyl 1H-indole-3-carboxylate. The results obtained were compared with the experimental data and were also analysed in terms of structural enthalpic group contributions.

SYNTHESIS OF ENANTIOMERICALLY PURE (R)-2-SULFANYLPROPANOIC AND (S)-2-SULFANYLPROPANOIC ACIDS (THIOLACTIC ACID) FROM ETHYL (S)-LACTATE USING PIG-LIVER ESTERASE

NARCIS (Netherlands)

HOF, RP; KELLOGG, RM

1995-01-01

The methanesulfonates of optically pure ethyl (S)-lactate or ethyl (R)-2-chloropropanoate 5, obtained with inversion of configuration from ethyl (S)-lactate on treatment with SOCl2, can be substituted by caesium thiolates with inversion of configuration to yield (R) and (S) ethyl

Key Aroma Compounds in Lippia dulcis (Dushi Button).

Science.gov (United States)

Schmitt, Rainer; Cappi, Michael; Pollner, Gwendola; Greger, Veronika

2018-03-14

An aroma extract dilution analysis (AEDA) applied on aroma extracts prepared from the edible flower Dushi Button ( Lippia dulcis) resulted in the detection of 34 odor-active compounds. The highest flavor dilution (FD) factors were determined for methyl 2-methylbutanoate, ethyl 2-methylbutanoate, 4-mercapto-4-methyl-2-pentanone, an unknown caramel-like compound, and vanillin. Quantitative measurements performed by application of stable isotope dilution assays (SIDA), followed by a calculation of odor activity values (OAVs), resulted in the revelation of 4-mercapto-4-methyl-2-pentanone, linalool, myrcene, ethyl 2-methylbutanoate, methyl 2-methylbutanoate, and ( Z)-3-hexenal as important contributors to the flavor of Dushi Buttons.

Experimental study of the density and viscosity of 1-ethyl-3-methylimidazolium ethyl sulfate

International Nuclear Information System (INIS)

Schmidt, H.; Stephan, M.; Safarov, J.; Kul, I.; Nocke, J.; Abdulagatov, I.M.; Hassel, E.

2012-01-01

Highlights: ► Density of the ionic liquid [EMIM][EtSO 4 ]. ► Viscosity of the ionic liquid [EMIM][EtSO 4 ]. ► Thermodynamic properties of ionic liquid [EMIM][EtSO 4 ]. ► Equation of state of ionic liquid [EMIM][EtSO 4 ]. - Abstract: Density and viscosity of 1-ethyl-3-methylimidazolium ethyl sulfate [EMIM][EtSO 4 ] have been measured over the temperature range from (283.15 to 413.15) K and at pressures up to 140 MPa and in the temperature range from (283.15 to 373.15) K at 0.1 MPa, respectively. The expanded uncertainty of the density, pressure, temperature, and viscosity measurements at the 95% confidence level with a coverage factor of k = 2 is estimated to be (0.01 to 0.08)%, 0.1%, 15 mK, and 0.35%, respectively. The measurements were carried out with an Anton–Paar DMA HPM vibration-tube densimeter and a fully automated SVM 3000 Anton–Paar rotational Stabinger viscometer. The vibration-tube densimeter was calibrated using various reference fluids, double-distilled water, methanol, toluene, and aqueous NaCl solutions. An empiric equation of state for [EMIM][EtSO 4 ] has been developed using the measured (p, ρ, T) data. This equation was used to calculate the various thermodynamic properties of the IL and for compare with measured properties (speed of sound and enthalpy). Theoretically based Arrhenius–Andrade and Vogel–Tamman–Fulcher type equations were use to describe of the temperature dependence of measured viscosities for [EMIM][EtSO 4 ]. All measured properties were detailed compared with the reported data by other author.

Teores de compostos orgânicos em cachaças produzidas na região norte fluminense - Rio de Janeiro Organic compounds contents in cachaças produced in the northern Rio de Janeiro State - RJ

Directory of Open Access Journals (Sweden)

Leandro Marelli de Souza

2009-01-01

Full Text Available This work aimed to quantify some organic compounds in "cachaças" (sugar cane spirit. The ethyl alcohol was quantified by densimetry, after distillation. The acetic acid, methyl alcohol, n-propyl alcohol, n-butyl alcohol, isobutyl alcohol, isoamyl alcohol (mixture of 2-methyl-butyl and 3-methyl-butyl, ethyl acetate and acetaldehyde were determined by gas chromatography; and the furfural, 5-hydroxy-methylfurfural and acrolein by high efficiency liquid chromatography. From the 30 samples analyzed, 63.3% showed non-conformity with national legislation regarding at least one of the analyzed components.

Synergistic solvent extraction investigation of Am (III), Eu (III), Zn(II), and Cs(I), using 2-heptyl-2-methyl-nonanoic acid mixed with different organophosphorus compounds from nitrate media. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

El-Naggar, H A; Ramadan, A; Abdel-Fattah, A [Nuclear Chemistry Department, Hot Laboratories Center, Atomic Energy Authority, Cairo (Egypt)

1996-03-01

Extraction studies for investigating the effect of mixing 2-heptyl-2-methyl nonanoic acid (HA) with a number of organophosphorus compounds; namely tributyl phosphate (TBP), terphenyl phosphate oxide (TPPO); tri octyl phosphine oxide (TOPO) or bis-2-(ethyl hexyl) phosphoric acid (HDEHP) in benzene on the extraction of trace elements Am(III), Eu(III), Zn(II), and Cs(I) from nitrate media of ionic strength, I=0.1 M were carried out. The effect of adding different organophosphorus compounds to HA was tested to account for the presence or absence of the phenomenon of synergism. It was found that TBP, TPPO, and TOPO causing some antagonistic effects for the elements studied. Extraction enhancement was only observed with bis- (2-ethyl-hexyl) -phosphoric acid (HDEHP) for all the elements investigated. The extraction mechanisms as well as the thermodynamic parameters for the mixed extracted species are discussed. 19 figs.

Synergistic solvent extraction investigation of Am (III), Eu (III), Zn(II), and Cs(I), using 2-heptyl-2-methyl-nonanoic acid mixed with different organophosphorus compounds from nitrate media. Vol. 3

International Nuclear Information System (INIS)

El-Naggar, H.A.; Ramadan, A.; Abdel-Fattah, A.

1996-01-01

Extraction studies for investigating the effect of mixing 2-heptyl-2-methyl nonanoic acid (HA) with a number of organophosphorus compounds; namely tributyl phosphate (TBP), terphenyl phosphate oxide (TPPO); tri octyl phosphine oxide (TOPO) or bis-2-(ethyl hexyl) phosphoric acid (HDEHP) in benzene on the extraction of trace elements Am(III), Eu(III), Zn(II), and Cs(I) from nitrate media of ionic strength, I=0.1 M were carried out. The effect of adding different organophosphorus compounds to HA was tested to account for the presence or absence of the phenomenon of synergism. It was found that TBP, TPPO, and TOPO causing some antagonistic effects for the elements studied. Extraction enhancement was only observed with bis- (2-ethyl-hexyl) -phosphoric acid (HDEHP) for all the elements investigated. The extraction mechanisms as well as the thermodynamic parameters for the mixed extracted species are discussed. 19 figs

Tailored Poly(2-oxazoline) Polymer Brushes to Control Protein Adsorption and Cell Adhesion

KAUST Repository

Zhang, Ning

2012-05-18

POx bottle-brush brushes (BBBs) are synthesized by SIPGP of 2-isopropenyl-2-oxazoline and consecutive LCROP of 2-oxazolines on 3-aminopropyltrimethoxysilane-modified silicon substrates. The side chain hydrophilicity and polarity are varied. The impact of the chemical composition and architecture of the BBB upon protein (fibronectin) adsorption and endothelial cell adhesion are investigated and prove extremely low protein adsorption and cell adhesion on BBBs with hydrophilic side chains such as poly(2-methyl-2-oxazoline) and poly(2-ethyl-2-oxazoline). The influence of the POx side chain terminal function upon adsorption and adhesion is minor but the side chain length has a significant effect on bioadsorption. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Tailored Poly(2-oxazoline) Polymer Brushes to Control Protein Adsorption and Cell Adhesion

KAUST Repository

Zhang, Ning; Pompe, Tilo; Amin, Ihsan; Luxenhofer, Robert; Werner, Carsten; Jordan, Rainer

2012-01-01

POx bottle-brush brushes (BBBs) are synthesized by SIPGP of 2-isopropenyl-2-oxazoline and consecutive LCROP of 2-oxazolines on 3-aminopropyltrimethoxysilane-modified silicon substrates. The side chain hydrophilicity and polarity are varied. The impact of the chemical composition and architecture of the BBB upon protein (fibronectin) adsorption and endothelial cell adhesion are investigated and prove extremely low protein adsorption and cell adhesion on BBBs with hydrophilic side chains such as poly(2-methyl-2-oxazoline) and poly(2-ethyl-2-oxazoline). The influence of the POx side chain terminal function upon adsorption and adhesion is minor but the side chain length has a significant effect on bioadsorption. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Central muscle relaxant activities of 2-methyl-3-aminopropiophenone derivatives].

Science.gov (United States)

Kontani, H; Mano, A; Koshiura, R; Yamazaki, M; Shimada, Y; Oshita, M; Morikawa, K; Kato, H; Ito, Y

1987-02-01

In this experiment, we synthetized new 2-methyl-3-aminopropiophenone (MP) derivatives, whose structure is known to have central muscle relaxant activities, and quinolizidine and indan . tetralin derivatives derived from MP by cyclization, and we investigated the central muscle relaxant activity. Among the quinolizidine derivatives, there was a very strong central depressant agent, trans (3H, 9aH)-3-(p-chloro) benzoyl-quinolizidine (HSR-740), and among the indan . tetralin derivatives, there was an excitant agents, trans (1H, 2H)-5-methoxy-3, 3-dimethyl-2-piperidinomethyl indan-1-ol (HSR-719). From the results, these derivatives were not considered to be adequate for central muscle relaxant. Among the MP derivatives, (4'-chloro-2'-methoxy-3-piperidino) propiophenone HCl (HSR-733) and (4'-ethyl-2-methyl-3-pyrrolidino) propiophenone HCl (HSR-770) strongly inhibited the cooperative movement in the rotating rod method using mice, and it exerted almost the same depressant activity on the cross extensor reflex using alpha-chloralose anesthetized rats. However, the inhibitory effects of HSR-733 on the anemic decerebrate rigidity and the rigidity induced by intracollicular decerebration in rats were weaker than those of HSR-770 and eperisone. In spinal cats, at a low dose (5 mg/kg, i.v.), HSR-733 depressed monosynaptic and dorsal root reflex potentials as compared with polysynaptic reflex potentials, and inhibitory effects of HSR-733 on these three reflex potentials were more potent than those of eperisone and HSR-770. Although HSR-770 acts on the spinal cord and supraspinal level on which eperisone has been reported to act, HSR-733 may mainly act on the spinal cord. These results indicate that the MP derivative with a 2-methyl group may be suitable as a central muscle relaxant. HSR-770, which has equipotent muscle relaxant activity to eperisone, exerted strong inhibitory effects on oxotremorine-induced tremor and weak inhibitory effects on spontaneous motor activity in the

ENZYMATIC PRODUCTION OF ETHYL OLEATE ESTER USING A LIPASE FROM CANDIDA ANTARCTICA B

Directory of Open Access Journals (Sweden)

N. Sampaio Neta

2012-05-01

Full Text Available Lipases are biocatalysts of great importance in different areas, being able to catalyze reactions in aqueous or organic media. Furthermore, these enzymes are capable of using several substrates being stable in a wide range of pH and temperatures. Lipases promote the esterification between fatty acids and ethanol producing oleate esters. The aim of this work is to produce ethyl oleate ester by enzymatic esterification of oleic acid with ethanol. A lipase from Candida antarctica type B was used at a temperature of 55 °C. The reaction was conducted using oleic acid, sodium sulfate anhydrous, lipase and ethanol, with a ratio of oleic acid (0.03 mol or 10 ml, lipase (0.1 mol or 0.01 g, sodium sulfate anhydrous (5 g and ethanol 99 % (100 ml. Several reaction times were studied, namely 48, 72, 96 and 120 hours. Nuclear Magnetic Resonance (1H and 13C and Infrared spectra confirmed the production of ethyl oleate ester for the studied conditions. The highest ethyl oleate production yield was obtained for 96 hours reaction time. Ethyl oleate esters have been reported to possess interesting applications in several industrial fields, such as food, aromatics, cosmetics, detergents, flavors and pharmaceuticals.

Protective Effect of Ethyl Acetate Fraction of Stereospermum Suaveolens Against Hepatic Oxidative Stress in STZ Diabetic Rats.

Science.gov (United States)

Balasubramanian, Thirumalaiswamy; Senthilkumar, G P; Karthikeyan, M; Chatterjee, Tapan Kumar

2013-07-01

Stereospermum suaveolens is a folk remedy for the treatment of diabetes and liver disorders in southern parts of India. In the present study, the protective effect of the ethyl acetate fraction of ethanol extract from S. suaveolens against hepatic oxidative stress was evaluated in streptozotocin (STZ)-induced diabetic rats for 14 days. The ethyl acetate fraction was administered orally to the STZ diabetic rats at the doses of 200 and 400 mg/kg. Blood glucose level was measured according to glucose oxidase method. In order to determine hepatoprotective activity, changes in the levels of serum biomarker enzymes such as aspartate transaminase (AST), alanine transaminase (ALT), and serum alkaline phosphatase (SALP) were assessed in the ethyl acetate fraction treated diabetic rats and were compared with the levels in diabetic control rats. In addition, the antioxidant activity of ethyl acetate fraction was evaluated using various hepatic parameters such as thiobarbituric acid reactive substances (TBARS), reduced glutathione (GSH), superoxide dismutase (SOD), and catalase (CAT). It was found that administration of ethyl acetate fraction (200 and 400 mg/kg) produced a significant (P SALP, while elevating the GSH levels, and SOD and CAT activities in diabetic rats. Histopathologic studies also revealed the protective effect of ethyl acetate fraction on the liver tissues of diabetic rats. It was concluded from this study that the ethyl acetate fraction from ethanol extract of S. suaveolens modulates the activity of enzymatic and nonenzymatic antioxidants and enhances the defense against hepatic oxidative stress in STZ-induced diabetic rats.

9-Hydroxyfurodysinin-O-ethyl Lactone: A New Sesquiterpene Isolated from the Tropical Marine Sponge Dysidea arenaria

Directory of Open Access Journals (Sweden)

P. Karuso

2005-10-01

Full Text Available A new sesquiterpene, 9-hydroxyfurodysinin-O-ethyl lactone, has been isolated from a New Caledonian Dysidea arenaria, along with three known compounds. The possible incorporation of the ethyl ether from the extraction solvent is discussed.

Geochemistry of silicon isotopes

Energy Technology Data Exchange (ETDEWEB)

Ding, Tiping; Li, Yanhe; Gao, Jianfei; Hu, Bin [Chinese Academy of Geological Science, Beijing (China). Inst. of Mineral Resources; Jiang, Shaoyong [China Univ. of Geosciences, Wuhan (China).

2018-04-01

Silicon is one of the most abundant elements in the Earth and silicon isotope geochemistry is important in identifying the silicon source for various geological bodies and in studying the behavior of silicon in different geological processes. This book starts with an introduction on the development of silicon isotope geochemistry. Various analytical methods are described and compared with each other in detail. The mechanisms of silicon isotope fractionation are discussed, and silicon isotope distributions in various extraterrestrial and terrestrial reservoirs are updated. Besides, the applications of silicon isotopes in several important fields are presented.

Synthesis of Ethyl Nalidixate: A Medicinal Chemistry Experiment

Science.gov (United States)

Leslie, Ray; Leeb, Elaine; Smith, Robert B.

2012-01-01

A series of laboratory experiments that complement a medicinal chemistry lecture course in drug design and development have been developed. The synthesis of ethyl nalidixate covers three separate experimental procedures, all of which can be completed in three, standard three-hour lab classes and incorporate aspects of green chemistry such as…

Radio-sensitizing effect of ethyl caffeate on nasopharyngeal ...

African Journals Online (AJOL)

3Department of Clinical Laboratory, The 5th People's Hospital of Ji'nan, Ji'nan ... Purpose: To investigate the radio-sensitizing effect of ethyl caffeate (ETF) on naso-pharyngeal ... malignant solid tumors of head and neck which ... Excess irradiation could result in severe side .... protein bands were probed with corresponding.

Going the distance with ethyl alcohol

International Nuclear Information System (INIS)

Hairston, D.W.

1995-01-01

If all had gone according to plan, ethyl alcohol would be in the driver's seat now, cruising down the highway and getting ready to speed into high gear. Instead, this renewable fuel, chemical reagent and solvent is navigating a complex obstacle course, watching warily for sharp turns and mixed signals. Globally, the supply and demand for all grades of ethyl alcohol is awry. Production of industrial-grade material is running at full throttle and prices are going up. Much of the upheaval over ethanol can be traced to the US Environmental Protection Agency and the renewable oxygenate standard (ROS) of the Clean Air Act. Under ROS, 15% of oxygenates used in gasoline sold this year was to be derived from a renewable source. Next month, that percentage was to have been doubled to 30%. Enticed by projections of upwards of 2 billion gal/yr of fermentation alcohol to comply with ROS, producers rushed to expand capacity. But to the producers' dismay, EPA was forced to backpedal on ROS. When representatives of the petroleum industry filed suit and won a stay, EPA rescinded its ROS regulation and ethanol producers were left in the lurch. High prices for corn is also putting the squeeze on inventories of industrial alcohol. Synthetic ethanol production, from ethylene for example, is booming, however. This paper discusses the ethanol market factors

Automated sequence- and stereo-specific assignment of methyl-labeled proteins by paramagnetic relaxation and methyl-methyl nuclear overhauser enhancement spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Venditti, Vincenzo; Fawzi, Nicolas L.; Clore, G. Marius, E-mail: mariusc@mail.nih.gov [National Institute of Diabetes and Digestive and Kidney Diseases, National Institutes of Health, Laboratory of Chemical Physics (United States)

2011-11-15

Methyl-transverse relaxation optimized spectroscopy is rapidly becoming the preferred NMR technique for probing structure and dynamics of very large proteins up to {approx}1 MDa in molecular size. Data interpretation, however, necessitates assignment of methyl groups which still presents a very challenging and time-consuming process. Here we demonstrate that, in combination with a known 3D structure, paramagnetic relaxation enhancement (PRE), induced by nitroxide spin-labels incorporated at only a few surface-exposed engineered cysteines, provides fast, straightforward and robust access to methyl group resonance assignments, including stereoassignments for the methyl groups of leucine and valine. Neither prior assignments, including backbone assignments, for the protein, nor experiments that transfer magnetization between methyl groups and the protein backbone, are required. PRE-derived assignments are refined by 4D methyl-methyl nuclear Overhauser enhancement data, eliminating ambiguities and errors that may arise due to the high sensitivity of PREs to the potential presence of sparsely-populated transient states.

[Intravenous ethyl alcohol in metabolic resuscitation].

Science.gov (United States)

Agolini, G; Lipartiti, T; Zaffiri, O; Musso, L; Belloni, G P

1980-11-01

Intravenously administered ethyl alcohol may be effective as analgesic and hypotensive peripheric vasoactive drug. In the Intensive Care Departments parenteral ethanol administration is infrequent because no "sure dosage" can be suggested in adults and children. Liver, kidney and C.N.S. diseases can worsen; foetopathy can follow. Drug-ethanol interaction may be particularly important for some patients admitted in Intensive Care Departments. Often the potential caloric support cannot be fully utilized ("empty" calories) and seldom hyperventilation, hyperlactacidemia and impaired protein synthesis can follow.

Methylation diet and methyl group genetics in risk for adenomatous polyp occurrence

Directory of Open Access Journals (Sweden)

Mark Lucock

2015-06-01

Conclusion: A methylation diet influences methyl group synthesis in the regulation of blood homocysteine level, and is modulated by genetic interactions. Methylation-related nutrients also interact with key genes to modify risk of AP, a precursor of colorectal cancer. Independent of diet, two methylation-related genes (A2756G-MS and A66G-MSR were directly associated with AP occurrence.

GC-MS and FI-IR analysis of the bio-oil with addition of ethyl acetate during storage

Directory of Open Access Journals (Sweden)

Le eZhang

2014-01-01

Full Text Available Different mass fractions (0%, 3%, 6%, 9%, 12%, and 15% of ethyl acetate were added to bio-oil for improving its storage stability during storage at 40℃ for 35d. For different bio-oils during storage, physical properties were characterized and chemical components were determined by GC-MS and FT-IR. The results of properties characterization showed that, addition of ethyl acetate could instantly lower bio-oil viscosity, water content, and dramatically decrease the rate of aging. pH value of bio-oil can be instantly improved by adding ethyl acetate. GC-MS results revealed that addition of various content of ethyl acetate into bio-oil and its storage at 40℃ for 35d could both lead to disappearance of previous compounds and generation of new compounds. FT-IR results showed that addition of various content of ethyl acetate into bio-oils and its storage at 40℃ for 35d could slightly change the wavenumbers of substantial functional groups in bio-oils.

Effect of Potent Ethyl Acetate Fraction of Stereospermum suaveolens Extract in Streptozotocin-Induced Diabetic Rats

Directory of Open Access Journals (Sweden)

T. Balasubramanian

2012-01-01

Full Text Available To evaluate the antihyperglycemic effect of ethyl acetate fraction of ethanol extract of Stereospermum suaveolens in streptozotocin-(STZ- induced diabetic rats by acute and subacute models. In this paper, various fractions of ethanol extract of Stereospermum suaveolens were prepared and their effects on blood glucose levels in STZ-induced diabetic rats were studied after a single oral administration (200?mg/kg. Administration of the ethyl acetate fraction at 200?mg/kg once daily for 14 days to STZ-induced diabetic rats was also carried out. The parameters such as the fasting blood glucose, hepatic glycogen content, and pancreatic antioxidant levels were monitored. In the acute study, the ethyl acetate fraction is the most potent in reducing the fasting serum glucose levels of the STZ-induced diabetic rats. The 14-day repeated oral administration of the ethyl acetate fraction significantly reduced the fasting blood glucose and pancreatic TBARS level and significantly increased the liver glycogen, pancreatic superoxide dismutase, and catalase activities as well as reduced glutathione levels. The histopathological studies during the subacute treatment have been shown to ameliorate the STZ-induced histological damage of pancreas. This paper concludes that the ethyl acetate fraction from ethanol extract of Stereospermum suaveolens possesses potent antihyperglycemic and antioxidant properties, thereby substantiating the use of plant in the indigenous system of medicine.

Reactions of guanine with methyl chloride and methyl bromide: O6-methylation versus charge transfer complex formation

Science.gov (United States)

Shukla, P. K.; Mishra, P. C.; Suhai, S.

Density functional theory (DFT) at the B3LYP/6-31+G* and B3LYP/AUG-cc-pVDZ levels was employed to study O6-methylation of guanine due to its reactions with methyl chloride and methyl bromide and to obtain explanation as to why the methyl halides cause genotoxicity and possess mutagenic and carcinogenic properties. Geometries of the various isolated species involved in the reactions, reactant complexes (RCs), and product complexes (PCs) were optimized in gas phase. Transition states connecting the reactant complexes with the product complexes were also optimized in gas phase at the same levels of theory. The reactant complexes, product complexes, and transition states were solvated in aqueous media using the polarizable continuum model (PCM) of the self-consistent reaction field theory. Zero-point energy (ZPE) correction to total energy and the corresponding thermal energy correction to enthalpy were made in each case. The reactant complexes of the keto form of guanine with methyl chloride and methyl bromide in water are appreciably more stable than the corresponding complexes involving the enol form of guanine. The nature of binding in the product complexes was found to be of the charge transfer type (O6mG+ · X-, X dbond Cl, Br). Binding of HCl, HBr, and H2O molecules to the PCs obtained with the keto form of guanine did not alter the positions of the halide anions in the PCs, and the charge transfer character of the PCs was also not modified due to this binding. Further, the complexes obtained due to the binding of HCl, HBr, and H2O molecules to the PCs had greater stability than the isolated PCs. The reaction barriers involved in the formation of PCs were found to be quite high (?50 kcal/mol). Mechanisms of genotoxicity, mutagenesis and carcinogenesis caused by the methyl halides appear to involve charge transfer-type complex formation. Thus the mechanisms of these processes involving the methyl halides appear to be quite different from those that involve the

Trans-methylation reactions in plants: focus on the activated methyl cycle.

Science.gov (United States)

Rahikainen, Moona; Alegre, Sara; Trotta, Andrea; Pascual, Jesús; Kangasjärvi, Saijaliisa

2018-02-01

Trans-methylation reactions are vital in basic metabolism, epigenetic regulation, RNA metabolism, and posttranslational control of protein function and therefore fundamental in determining the physiological processes in all living organisms. The plant kingdom is additionally characterized by the production of secondary metabolites that undergo specific hydroxylation, oxidation and methylation reactions to obtain a wide array of different chemical structures. Increasing research efforts have started to reveal the enzymatic pathways underlying the biosynthesis of complex metabolites in plants. Further engineering of these enzymatic machineries offers significant possibilities in the development of bio-based technologies, but necessitates deep understanding of their potential metabolic and regulatory interactions. Trans-methylation reactions are tightly coupled with the so-called activated methyl cycle (AMC), an essential metabolic circuit that maintains the trans-methylation capacity in all living cells. Tight regulation of the AMC is crucial in ensuring accurate trans-methylation reactions in different subcellular compartments, cell types, developmental stages and environmental conditions. This review addresses the organization and posttranslational regulation of the AMC and elaborates its critical role in determining metabolic regulation through modulation of methyl utilization in stress-exposed plants. © 2017 Scandinavian Plant Physiology Society.

Silicon heterojunction transistor

International Nuclear Information System (INIS)

Matsushita, T.; Oh-uchi, N.; Hayashi, H.; Yamoto, H.

1979-01-01

SIPOS (Semi-insulating polycrystalline silicon) which is used as a surface passivation layer for highly reliable silicon devices constitutes a good heterojunction for silicon. P- or B-doped SIPOS has been used as the emitter material of a heterojunction transistor with the base and collector of silicon. An npn SIPOS-Si heterojunction transistor showing 50 times the current gain of an npn silicon homojunction transistor has been realized by high-temperature treatments in nitrogen and low-temperature annealing in hydrogen or forming gas

21 CFR 177.2000 - Vinylidene chloride/methyl acrylate/methyl methacrylate polymers.

Science.gov (United States)

2010-04-01

... methacrylate polymers. 177.2000 Section 177.2000 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF...: POLYMERS Substances for Use as Basic Components of Single and Repeated Use Food Contact Surfaces § 177.2000 Vinylidene chloride/methyl acrylate/methyl methacrylate polymers. The vinylidene chloride/methyl acrylate...

Hyperfine interactions of a muoniated ethyl radical in supercritical CO2

International Nuclear Information System (INIS)

Cormier, Philip; Taylor, Becky; Ghandi, Khashayar

2009-01-01

A muoniated ethyl radical was studied in supercritical carbon dioxide. The muon and the proton hyperfine coupling constants were measured over temperatures ranging from 305 to 475 K, and a density range from 0.2 to 0.7 (g cm -3 ). A decrease was found in the muon hyperfine coupling constants as a function of the density, which can be attributed to the interaction between the CO 2 molecule and the p-orbital of the ethyl radical. The changes to the α-proton and β-proton hyperfine coupling constants with density are attributed to changes in the overall geometry in the formed radical. This system was modeled using quantum calculations.

Remedial Investigation Badger Army Ammunition Plant, Baraboo, Wisconsin. Volume 1. Text Sections 1 Through 12

Science.gov (United States)

1993-04-01

VOCs (acetone [ACET], trichlorofluoromethane [CCL3F], methyl ethyl ketone [MEK]) sporadically detected at very low concentrations (< 1 parts per billion...associated with the site includes red pine ( Pinus resinosa), hickories, cedar (Thuja occidentalis), and American elm (Ulmus americana). Grasses and weedy...cd)pyrene ICDPYR iron FE lead PB magnesium MG *manganese MN mercury HG methylene chloride CH12CL2 methyl ethyl ketone or 2-butanone MIEK

Whole-genome methylation caller designed for methyl- DNA ...

African Journals Online (AJOL)

etchie

2013-02-20

Feb 20, 2013 ... Key words: Methyl-DNA immunoprecipitation, next-generation sequencing, Hidden ... its response to environmental cues. .... have a great potential to become the most cost-effective ... hg18 reference genome (set to 0 if not present in retrieved reads). ..... DNA methylation patterns and epigenetic memory.

Protective Effect of Ethyl Acetate Fraction of Stereospermum Suaveolens Against Hepatic Oxidative Stress in STZ Diabetic Rats

Directory of Open Access Journals (Sweden)

Thirumalaiswamy Balasubramanian

2013-07-01

Full Text Available Stereospermum suaveolens is a folk remedy for the treatment of diabetes and liver disorders in southern parts of India. In the present study, the protective effect of the ethyl acetate fraction of ethanol extract from S. suaveolens against hepatic oxidative stress was evaluated in streptozotocin (STZ-induced diabetic rats for 14 days. The ethyl acetate fraction was administered orally to the STZ diabetic rats at the doses of 200 and 400 mg/kg. Blood glucose level was measured according to glucose oxidase method. In order to determine hepatoprotective activity, changes in the levels of serum biomarker enzymes such as aspartate transaminase (AST, alanine transaminase (ALT, and serum alkaline phosphatase (SALP were assessed in the ethyl acetate fraction treated diabetic rats and were compared with the levels in diabetic control rats. In addition, the antioxidant activity of ethyl acetate fraction was evaluated using various hepatic parameters such as thiobarbituric acid reactive substances (TBARS, reduced glutathione (GSH, superoxide dismutase (SOD, and catalase (CAT. It was found that administration of ethyl acetate fraction (200 and 400 mg/kg produced a significant (P<0.001 fall in fasting blood glucose level, TBARS, bilirubin, AST, ALT, and SALP, while elevating the GSH levels, and SOD and CAT activities in diabetic rats. Histopathologic studies also revealed the protective effect of ethyl acetate fraction on the liver tissues of diabetic rats. It was concluded from this study that the ethyl acetate fraction from ethanol extract of S. suaveolens modulates the activity of enzymatic and nonenzymatic antioxidants and enhances the defense against hepatic oxidative stress in STZ-induced diabetic rats.

Solubility of daidzin in different organic solvents and (ethyl alcohol + water) mixed solvents

International Nuclear Information System (INIS)

Fan, Jie-Ping; Yang, Dan; Xu, Xiao-Kang; Guo, Xiao-Jie; Zhang, Xue-Hong

2015-01-01

Highlights: • The solubilities of daidzin were measured in various solvents. • The solubility data were correlated by three models. • The thermodynamic properties of the dissolution process were also determined. - Abstract: The solubility of daidzin in different organic solvents and (ethyl alcohol + water) mixed solvents was measured by high performance liquid chromatography (HPLC) analysis method from T = (283.2 to 323.2) K at atmosphere pressure. The results show that at higher temperature more daidzin dissolves, and moreover, the solubility increases with the ethyl alcohol mole fraction increase in the (ethyl alcohol + water) mixed solvents. The experimental solubility values were correlated by a simplified thermodynamic equation, λh equation and modified Apelblat equation. Based on the solubility of daidzin, the enthalpy and entropy of solution were also evaluated by van’t Hoff equation. The results illustrated that the dissolution process of daidzin is endothermic and entropy driven

Vertical integration of high-Q silicon nitride microresonators into silicon-on-insulator platform.

Science.gov (United States)

Li, Qing; Eftekhar, Ali A; Sodagar, Majid; Xia, Zhixuan; Atabaki, Amir H; Adibi, Ali

2013-07-29

We demonstrate a vertical integration of high-Q silicon nitride microresonators into the silicon-on-insulator platform for applications at the telecommunication wavelengths. Low-loss silicon nitride films with a thickness of 400 nm are successfully grown, enabling compact silicon nitride microresonators with ultra-high intrinsic Qs (~ 6 × 10(6) for 60 μm radius and ~ 2 × 10(7) for 240 μm radius). The coupling between the silicon nitride microresonator and the underneath silicon waveguide is based on evanescent coupling with silicon dioxide as buffer. Selective coupling to a desired radial mode of the silicon nitride microresonator is also achievable using a pulley coupling scheme. In this work, a 60-μm-radius silicon nitride microresonator has been successfully integrated into the silicon-on-insulator platform, showing a single-mode operation with an intrinsic Q of 2 × 10(6).

Tritium as an indicator of CH3 and C2H5 radicals in ethane pyrolysis

International Nuclear Information System (INIS)

Kaminski, A.M.; Sobkowski, J.

1979-01-01

The concentration of methyl and ethyl radicals formed during the pyrolysis of ethane was determined by radiochemical method. The dominant role of ethyl radicals in the pyrolysis of ethane was proved. (author)

Acquisition of resistance to 1-(4-amino-2-methyl-5-pyrimidinyl) methyl-3-(2-chloroethyl)-3-nitrosourea hydrochloride in V79 cells through increased removal of O6-alkylguanine.

Science.gov (United States)

Satoh, M S; Huh, N H; Horie, Y; Thomale, J; Rajewsky, M F; Kuroki, T

1987-10-01

The molecular mechanism of acquisition of resistance to 1-(4-amino-2-methyl-5-pyrimidinyl)-methyl-3-(2-chloroethyl)-3-nitroso ure a hydrochloride (ACNU) was investigated using ACNU-resistant clones (ACNUr-1-4) isolated from the V79 cell line. The binding level of alkyl cyanate, a decomposition product of ACNU, to protein in ACNUr-1 cells was not less than that in the parental V79 cells, indicating that the acquired resistance was not due to a reduced intracellular concentration of ACNU. Because O6-chloroethylguanine, an intermediate in cytotoxic interstrand cross-link formation by ACNU, is known to be repaired by the same mechanism as O6-ethyldeoxyguanosine (O6-EtdGuo), we quantitated O6-EtdGuo by radioimmunoassay at various times after exposure of cells to 100 micrograms/ml N-ethyl-N-nitrosourea for 20 min. In V79 cells, elimination of O6-EtdGuo was negligible, but in all four resistant clones, 30 to 59% of the O6-EtdGuo was removed within 24 hr after exposure. This increased removal of O6-EtdGuo among the resistant clones was associated with the activity of O6-alkylguanine DNA alkyltransferase (O6-AGT) determined using cell extracts. The present results indicate that increased removal of O6-chloroethylguanine in ACNU-resistant clones by O6-AGT is mechanistically linked to the acquisition of resistance to ACNU.

Analytical and Experimental Evaluation of Joining Silicon Carbide to Silicon Carbide and Silicon Nitride to Silicon Nitride for Advanced Heat Engine Applications Phase II

Energy Technology Data Exchange (ETDEWEB)

Sundberg, G.J.

1994-01-01

Techniques were developed to produce reliable silicon nitride to silicon nitride (NCX-5101) curved joins which were used to manufacture spin test specimens as a proof of concept to simulate parts such as a simple rotor. Specimens were machined from the curved joins to measure the following properties of the join interlayer: tensile strength, shear strength, 22 C flexure strength and 1370 C flexure strength. In parallel, extensive silicon nitride tensile creep evaluation of planar butt joins provided a sufficient data base to develop models with accurate predictive capability for different geometries. Analytical models applied satisfactorily to the silicon nitride joins were Norton's Law for creep strain, a modified Norton's Law internal variable model and the Monkman-Grant relationship for failure modeling. The Theta Projection method was less successful. Attempts were also made to develop planar butt joins of siliconized silicon carbide (NT230).

A Study on Spectro-Analytical Aspects, DNA - Interaction, Photo-Cleavage, Radical Scavenging, Cytotoxic Activities, Antibacterial and Docking Properties of 3 - (1 - (6 - methoxybenzo [d] thiazol - 2 - ylimino) ethyl) - 6 - methyl - 3H - pyran - 2, 4 - dione and its Metal Complexes.

Science.gov (United States)

Ravi, Mudavath; Chennam, Kishan Prasad; Ushaiah, B; Eslavath, Ravi Kumar; Perugu, Shyam; Ajumeera, Rajanna; Devi, Ch Sarala

2015-09-01

The focus of the present work is on the design, synthesis, characterization, DNA-interaction, photo-cleavage, radical scavenging, in-vitro cytotoxicity, antimicrobial, docking and kinetic studies of Cu (II), Cd (II), Ce (IV) and Zr (IV) metal complexes of an imine derivative, 3 - (1 - (6 - methoxybenzo [d] thiazol - 2 - ylimino) ethyl) - 6 - methyl - 3H - pyran - 2, 4 - dione. The investigation of metal ligand interactions for the determination of composition of metal complexes, corresponding kinetic studies and antioxidant activity in solution was carried out by spectrophotometric methods. The synthesized metal complexes were characterized by EDX analysis, Mass, IR, (1)H-NMR, (13)C-NMR and UV-Visible spectra. DNA binding studies of metal complexes with Calf thymus (CT) DNA were carried out at room temperature by employing UV-Vis electron absorption, fluorescence emission and viscosity measurement techniques. The results revealed that these complexes interact with DNA through intercalation. The results of in vitro antibacterial studies showed the enhanced activity of chelating agent in metal chelated form and thus inferring scope for further development of new therapeutic drugs. Cell viability experiments indicated that all complexes showed significant dose dependent cytotoxicity in selected cell lines. The molecular modeling and docking studies were carried out with energy minimized structures of metal complexes to identify the receptor to metal interactions.

DNA Methylation and Methylation Polymorphism in Genetically Stable In vitro Regenerates of Jatropha curcas L. Using Methylation-Sensitive AFLP Markers.

Science.gov (United States)

Rathore, Mangal S; Jha, Bhavanath

2016-03-01

The present investigation aimed to evaluate the degree and pattern of DNA methylation using methylation-sensitive AFLP (MS-AFLP) markers in genetically stable in vitro regenerates of Jatropha curcas L.. The genetically stable in vitro regenerates were raised through direct organogenesis via enhanced axillary shoot bud proliferation (Protocol-1) and in vitro-derived leaf regeneration (Protocol-2). Ten selective combinations of MS-AFLP primers produced 462 and 477 MS-AFLP bands in Protocol-1 (P-1) and Protocol-2 (P-2) regenerates, respectively. In P-1 regenerates, 15.8-31.17 % DNA was found methylated with an average of 25.24 %. In P-2 regenerates, 15.93-32.7 % DNA was found methylated with an average of 24.11 %. Using MS-AFLP in P-1 and P-2 regenerates, 11.52-25.53 % and 13.33-25.47 % polymorphism in methylated DNA was reported, respectively. Compared to the mother plant, P-1 regenerates showed hyper-methylation while P-2 showed hypo-methylation. The results clearly indicated alternation in degree and pattern of DNA methylation; hence, epigenetic instability in the genetically stable in vitro regenerates of J. curcas, developed so far using two different regeneration systems and explants of two different origins. The homologous nucleotide fragments in genomes of P-1 and P-2 regenerates showing methylation re-patterning might be involved in immediate adaptive responses and developmental processes through differential regulation of transcriptome under in vitro conditions.

Vapour pressures and osmotic coefficients of binary mixtures of 1-ethyl-3-methylimidazolium ethylsulfate and 1-ethyl-3-methylpyridinium ethylsulfate with alcohols at T = 323.15 K

International Nuclear Information System (INIS)

Calvar, Noelia; Gonzalez, Begona; Dominguez, Angeles; Macedo, Eugenia A.

2009-01-01

Osmotic coefficients of binary mixtures containing alcohols (ethanol, 1-propanol, and 2-propanol) and the ionic liquids 1-ethyl-3-methylimidazolium ethylsulfate and 1-ethyl-3-methylpyridinium ethylsulfate were determined at T = 323.15 K. Vapour pressure and activity coefficients of the studied systems were calculated from experimental data. The extended Pitzer model modified by Archer, and the modified NRTL model (MNRTL) were used to correlate the experimental data, obtaining standard deviations lower than 0.012 and 0.031, respectively. The mean molal activity coefficients and the excess Gibbs free energy of the studied binary mixtures were calculated from the parameters obtained with the extended Pitzer model of Archer.

Determinação de metil-etil-cetona em amostras de urina com amostragem por micro extração em fase sólida (MEFS em headspace associada à cromatografia gasosa com detector de ionização de chama (CG-DIC Determination of methyl ethyl ketone in urine samples by headspace solid phase micro extraction (SPME sampling associated to gas chromatography with flame-ionization detectoR (GC-FID

Directory of Open Access Journals (Sweden)

Marina Venzon Antunes

2008-01-01

Full Text Available Methyl ethyl ketone (MEK is a solvent commonly used in chemical, paint and shoe industry. The aim of this study was to develop and validate a method for urinary quantification of MEK, employing headspace solid phase micro extraction sampling (SPME coupled to gas chromatography with flame ionization detection (GC-FID. The calibration curve (y=4.6851x-0.0011 presented good linearity with r²=0.9993. Accuracy (94-109%, intra-assay precision (4.07-5.91% and inter-assay precision (3.03-5.62% were acceptable. The quantification limit was 0.19 mg/L. This low cost method can be used routinely in the biological monitoring of occupational exposure to MEK, according to the requirements of the Brazilian legislation.

Electrical leakage phenomenon in heteroepitaxial cubic silicon carbide on silicon

Science.gov (United States)

Pradeepkumar, Aiswarya; Zielinski, Marcin; Bosi, Matteo; Verzellesi, Giovanni; Gaskill, D. Kurt; Iacopi, Francesca

2018-06-01

Heteroepitaxial 3C-SiC films on silicon substrates are of technological interest as enablers to integrate the excellent electrical, electronic, mechanical, thermal, and epitaxial properties of bulk silicon carbide into well-established silicon technologies. One critical bottleneck of this integration is the establishment of a stable and reliable electronic junction at the heteroepitaxial interface of the n-type SiC with the silicon substrate. We have thus investigated in detail the electrical and transport properties of heteroepitaxial cubic silicon carbide films grown via different methods on low-doped and high-resistivity silicon substrates by using van der Pauw Hall and transfer length measurements as test vehicles. We have found that Si and C intermixing upon or after growth, particularly by the diffusion of carbon into the silicon matrix, creates extensive interstitial carbon traps and hampers the formation of a stable rectifying or insulating junction at the SiC/Si interface. Although a reliable p-n junction may not be realistic in the SiC/Si system, we can achieve, from a point of view of the electrical isolation of in-plane SiC structures, leakage suppression through the substrate by using a high-resistivity silicon substrate coupled with deep recess etching in between the SiC structures.

Analysis of DNA methylation in Arabidopsis thaliana based on methylation-sensitive AFLP markers.

Science.gov (United States)

Cervera, M T; Ruiz-García, L; Martínez-Zapater, J M

2002-12-01

AFLP analysis using restriction enzyme isoschizomers that differ in their sensitivity to methylation of their recognition sites has been used to analyse the methylation state of anonymous CCGG sequences in Arabidopsis thaliana. The technique was modified to improve the quality of fingerprints and to visualise larger numbers of scorable fragments. Sequencing of amplified fragments indicated that detection was generally associated with non-methylation of the cytosine to which the isoschizomer is sensitive. Comparison of EcoRI/ HpaII and EcoRI/ MspI patterns in different ecotypes revealed that 35-43% of CCGG sites were differentially digested by the isoschizomers. Interestingly, the pattern of digestion among different plants belonging to the same ecotype is highly conserved, with the rate of intra-ecotype methylation-sensitive polymorphisms being less than 1%. However, pairwise comparisons of methylation patterns between samples belonging to different ecotypes revealed differences in up to 34% of the methylation-sensitive polymorphisms. The lack of correlation between inter-ecotype similarity matrices based on methylation-insensitive or methylation-sensitive polymorphisms suggests that whatever the mechanisms regulating methylation may be, they are not related to nucleotide sequence variation.

Ethyl ester purpurine-18 from Gossypium mustelinum (Malvaceae)

International Nuclear Information System (INIS)

Silva, Tania Maria Sarmento; Camara, Celso Amorim; Barbosa-Filho, Jose Maria; Giulietti, Ana Maria

2010-01-01

The phaeophorbide ethyl ester named Purpurine-18 and the flavonoids quercetin and kaempferol were obtained by chromatographic procedures from the chloroform fraction of aerial parts of Gossypium mustelinum. The structure of these compound was determined by NMR, IR and mass spectra data analysis. This is the first occurrence of this compound in Angiosperm. (author)

Fluorescence and thermoluminescence in silicon oxide films rich in silicon

International Nuclear Information System (INIS)

Berman M, D.; Piters, T. M.; Aceves M, M.; Berriel V, L. R.; Luna L, J. A.

2009-10-01

In this work we determined the fluorescence and thermoluminescence (TL) creation spectra of silicon rich oxide films (SRO) with three different silicon excesses. To study the TL of SRO, 550 nm of SRO film were deposited by Low Pressure Chemical Vapor Deposition technique on N-type silicon substrates with resistivity in the order of 3 to 5 Ω-cm with silicon excess controlled by the ratio of the gases used in the process, SRO films with Ro= 10, 20 and 30 (12-6% silicon excess) were obtained. Then, they were thermally treated in N 2 at high temperatures to diffuse and homogenize the silicon excess. In the fluorescence spectra two main emission regions are observed, one around 400 nm and one around 800 nm. TL creation spectra were determined by plotting the integrated TL intensity as function of the excitation wavelength. (Author)

Volatile compounds responsible for aroma of Jutrzenka liquer wine.

Science.gov (United States)

Jeleń, Henryk H; Majcher, Małgorzata; Dziadas, Mariusz; Zawirska-Wojtasiak, Renata; Czaczyk, Katarzyna; Wąsowicz, Erwin

2011-10-21

Jutrzenka is a sweet liquer wine produced in Poland from the grape variety of the same name, developed in Poland to withstand the harsh climate of winery regions. Jutrzenka wine has a characteristic aroma with strong fruity and flowery notes, which make it unique among other liquer wines as demonstrated in sensory profile analysis. The work was aimed at characterization of volatile compounds in this wine, with the emphasis on characterization of compounds responsible for its unique aroma. Gas chromatography-olfactometry (GC-O) was applied to identify the key odorants using aroma extract dilution analysis (AEDA) approach. To facilitate free and bound terpenes and C(13)-norisoprenoids identification solid phase extraction (SPE) was used followed by GC/MS. Among identified key odorants β-damascenone was the compound having the highest FD (4096), followed by isoamyl alcohol, 4-mercapto-4-methyl-2-pentanone (FD=2048), methional, linalool, ethyl decanoate (FD=1024) and ethyl hexanoate, furaneol (FD=512). Other significant compounds were ethyl 2-methyl propanoate, ethyl 2-methylbutanoate and phenyl ethyl alcohol. Determination of odor activity values (OAV) showed the highest values for β-damascenone (566), 4-mercapto-4-methyl-2-pentanone (288) ethyl hexanoate (32) and linalool (7). Jutrzenka exhibited also a rich profile of free, and to lesser extent bound terpenes. Copyright © 2011 Elsevier B.V. All rights reserved.

The global DNA methylation surrogate LINE-1 methylation is correlated with MGMT promoter methylation and is a better prognostic factor for glioma.

Directory of Open Access Journals (Sweden)

Fumiharu Ohka

Full Text Available Gliomas are the most frequently occurring primary brain tumor in the central nervous system of adults. Glioblastoma multiformes (GBMs, WHO grade 4 have a dismal prognosis despite the use of the alkylating agent, temozolomide (TMZ, and even low grade gliomas (LGGs, WHO grade 2 eventually transform to malignant secondary GBMs. Although GBM patients benefit from promoter hypermethylation of the O(6-methylguanine-DNA methyltransferase (MGMT that is the main determinant of resistance to TMZ, recent studies suggested that MGMT promoter methylation is of prognostic as well as predictive significance for the efficacy of TMZ. Glioma-CpG island methylator phenotype (G-CIMP in the global genome was shown to be a significant predictor of improved survival in patients with GBM. Collectively, we hypothesized that MGMT promoter methylation might reflect global DNA methylation. Additionally in LGGs, the significance of MGMT promoter methylation is still undetermined. In the current study, we aimed to determine the correlation between clinical, genetic, and epigenetic profiles including LINE-1 and different cancer-related genes and the clinical outcome in newly diagnosed 57 LGG and 54 GBM patients. Here, we demonstrated that (1 IDH1/2 mutation is closely correlated with MGMT promoter methylation and 1p/19q codeletion in LGGs, (2 LINE-1 methylation levels in primary and secondary GBMs are lower than those in LGGs and normal brain tissues, (3 LINE-1 methylation is proportional to MGMT promoter methylation in gliomas, and (4 higher LINE-1 methylation is a favorable prognostic factor in primary GBMs, even compared to MGMT promoter methylation. As a global DNA methylation marker, LINE-1 may be a promising marker in gliomas.

Buried oxide layer in silicon

Science.gov (United States)

Sadana, Devendra Kumar; Holland, Orin Wayne

2001-01-01

A process for forming Silicon-On-Insulator is described incorporating the steps of ion implantation of oxygen into a silicon substrate at elevated temperature, ion implanting oxygen at a temperature below 200.degree. C. at a lower dose to form an amorphous silicon layer, and annealing steps to form a mixture of defective single crystal silicon and polycrystalline silicon or polycrystalline silicon alone and then silicon oxide from the amorphous silicon layer to form a continuous silicon oxide layer below the surface of the silicon substrate to provide an isolated superficial layer of silicon. The invention overcomes the problem of buried isolated islands of silicon oxide forming a discontinuous buried oxide layer.

Recognition of methylated DNA through methyl-CpG binding domain proteins

DEFF Research Database (Denmark)

Zou, Xueqing; Ma, Wen; Solov'yov, Ilia

2012-01-01

DNA methylation is a key regulatory control route in epigenetics, involving gene silencing and chromosome inactivation. It has been recognized that methyl-CpG binding domain (MBD) proteins play an important role in interpreting the genetic information encoded by methylated DNA (mDNA). Although...... the function of MBD proteins has attracted considerable attention and is well characterized, the mechanism underlying mDNA recognition by MBD proteins is still poorly understood. In this article, we demonstrate that the methyl-CpG dinucleotides are recognized at the MBD-mDNA interface by two MBD arginines...

78 FR 3377 - Notice of Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or...

Science.gov (United States)

2013-01-16

... acetanilide) and its metabolites containing either the 2-ethyl-6-methylaniline (EMA) or the 2-(1-hydroxyethyl... inadvertent residues of the herbicide acetochlor (2-chloro-2'-methyl- 6'-ethyl-N-ethoxymethyl acetanilide) and...

Ion beam studied of silicon oxynitride and silicon nitroxide thin layers

International Nuclear Information System (INIS)

Oude Elferink, J.B.

1989-01-01

In this the processes occurring during high temperature treatments of silicon oxynitride and silicon oxide layers are described. Oxynitride layers with various atomic oxygen to nitrogen concentration ration (O/N) are considered. The high energy ion beam techniques Rutherford backscattering spectroscopy, elastic recoil detection and nuclear reaction analysis have been used to study the layer structures. A detailed discussion of these ion beam techniques is given. Numerical methods used to obtain quantitative data on elemental compositions and depth profiles are described. The electrical compositions and depth profiles are described. The electrical properties of silicon nitride films are known to be influenced by the behaviour of hydrogen in the film during high temperature anneling. Investigations of the behaviour of hydrogen are presented. Oxidation of silicon (oxy)nitride films in O 2 /H 2 0/HCl and nitridation of silicon dioxide films in NH 3 are considered since oxynitrides are applied as an oxidation mask in the LOCOS (Local oxidation of silicon) process. The nitridation of silicon oxide layers in an ammonia ambient is considered. The initial stage and the dependence on the oxide thickness of nitrogen and hydrogen incorporation are discussed. Finally, oxidation of silicon oxynitride layers and of silicon oxide layers are compared. (author). 76 refs.; 48 figs.; 1 tab

Efeitos da dessecação com glyphosate e chlorimuron-ethyl na comunidade infestante e na produtividade da soja Effects of dissection with glyphosate and chlorimuron-ethyl on weed community and soybean yield

Directory of Open Access Journals (Sweden)

L.B Carvalho

2009-12-01

Full Text Available O efeito de dessecantes sobre o período anterior à interferência (PAI pode auxiliar na tomada de decisão para o manejo das plantas daninhas. O objetivo desta pesquisa foi verificar se a adição de chlorimuron-ethyl ao glyphosate, para dessecação em pré-semeadura, altera a extensão do PAI na soja. O experimento foi realizado em Jaboticabal-SP, Brasil, submetendo-se o cultivar Monsoy 7908RR a oito períodos de convivência com plantas daninhas, além de testemunhas no mato e no limpo, nos quais foram aplicados dois grupos de tratamentos: glyphosate e glyphosate + chlorimuron-ethyl. Em cada período, foram calculados o índice de importância relativa e os índices de diversidade e equitabilidade; por meio da análise de regressão dos dados de produtividade de grãos, determinou-se o PAI. Digitaria insularis, Acanthospermum hispidum, Raphanus raphanistrum e Commelina benghalensis apresentaram maior importância relativa. Os índices de diversidade e equitabilidade oscilaram durante os períodos, e a diferença entre as plantas daninhas fundamentou-se no acúmulo de massa seca. O PAI na soja no tratamento com glyphosate foi de 37 dias após a semeadura (DAS e de 51 DAS naquele com glyphosate + chlorimuron-ethyl. A adição de chlorimuron-ethyl ao glyphosate permite que a cultura conviva mais tempo com as plantas daninhas sem que ocorra redução significativa na produtividade.The effects of burndown herbicides on the period before weed interference (PBI may provide support to weed management decision-making. The objective of this research was to verify whether the PBI is affected by the application of glyphosate plus chlorimuron-ethyl to pre-sowing burndown in soybean. The experiment was carried out in Jaboticabal-SP, Brazil, submitting the cultivar Monsoy 7908RR to eight coexistence periods with weeds, maintaining weedy and-weed-free checks, which were applied to two groups of treatments: glyphosate and glyphosate + chlorimuron-ethyl. At

Tuning adhesion forces between functionalized gold colloidal nanoparticles and silicon AFM tips: role of ligands and capillary forces.

Science.gov (United States)

Oras, Sven; Vlassov, Sergei; Berholts, Marta; Lõhmus, Rünno; Mougin, Karine

2018-01-01

Adhesion forces between functionalized gold colloidal nanoparticles (Au NPs) and scanning probe microscope silicon tips were experimentally investigated by atomic force microscopy (AFM) equipped with PeakForce QNM (Quantitative Nanoscale Mechanics) module. Au NPs were synthesized by a seed-mediated process and then functionalized with thiols containing different functional groups: amino, hydroxy, methoxy, carboxy, methyl, and thiol. Adhesion measurements showed strong differences between NPs and silicon tip depending on the nature of the tail functional group. The dependence of the adhesion on ligand density for different thiols with identical functional tail-group was also demonstrated. The calculated contribution of the van der Waals (vdW) forces between particles was in good agreement with experimentally measured adhesive values. In addition, the adhesion forces were evaluated between flat Au films functionalized with the same molecular components and silicon tips to exclude the effect of particle shape on the adhesion values. Although adhesion values on flat substrates were higher than on their nanoparticle counterparts, the dependance on functional groups remained the same.

Supercritical antisolvent co-precipitation of rifampicin and ethyl cellulose

CSIR Research Space (South Africa)

Djerafi, R

2017-05-01

Full Text Available . Using the solvent mixture, co-precipitates with particle sizes ranging between 190 and 230 nm were obtained with drug loading and drug precipitation yield from respectively 8.5 to 38.5 and 42.4 to 77.2% when decreasing the ethyl cellulose...

Nonlinear silicon photonics

Science.gov (United States)

Tsia, Kevin K.; Jalali, Bahram

2010-05-01

An intriguing optical property of silicon is that it exhibits a large third-order optical nonlinearity, with orders-ofmagnitude larger than that of silica glass in the telecommunication band. This allows efficient nonlinear optical interaction at relatively low power levels in a small footprint. Indeed, we have witnessed a stunning progress in harnessing the Raman and Kerr effects in silicon as the mechanisms for enabling chip-scale optical amplification, lasing, and wavelength conversion - functions that until recently were perceived to be beyond the reach of silicon. With all the continuous efforts developing novel techniques, nonlinear silicon photonics is expected to be able to reach even beyond the prior achievements. Instead of providing a comprehensive overview of this field, this manuscript highlights a number of new branches of nonlinear silicon photonics, which have not been fully recognized in the past. In particular, they are two-photon photovoltaic effect, mid-wave infrared (MWIR) silicon photonics, broadband Raman effects, inverse Raman scattering, and periodically-poled silicon (PePSi). These novel effects and techniques could create a new paradigm for silicon photonics and extend its utility beyond the traditionally anticipated applications.

Ethyl Alcohol Extract of Hizikia fusiforme Induces Caspase ...

African Journals Online (AJOL)

Erah

In this study, the role of the ethyl alcohol extract of H. fusiforme (EAHF) in the induction of apoptosis in ... closely related to the induction of apoptosis via the downregulation of IAP family members such as IAP-. 1, IAP-2 ... induces apoptosis in a variety of cancer cells through ... Total cell extracts were prepared using PRO-.

Fabrication of Up-Conversion Phosphor Films on Flexible Substrates Using a Nanostructured Organo-Silicon.

Science.gov (United States)

Jeon, Young-Sun; Kim, Tae-Un; Kim, Seon-Hoon; Lee, Young-Hwan; Choi, Pil-Son; Hwang, Kyu-Seog

2018-03-01

Up-conversion phosphors have attracted considerable attention because of their applications in solid-state lasers, optical communications, flat-panel displays, photovoltaic cells, and biological labels. Among them, NaYF4 is reported as one of the most efficient hosts for infrared to visible photon up-conversion of Yb3+ and Er3+ ions. However, a low-temperature method is required for industrial scale fabrication of photonic and optoelectronic devices on flexible organic substrates. In this study, hexagonal β-NaYF4: 3 mol% Yb3+, 3 mol% Er3+ up-conversion phosphor using Ca2+ was prepared by chemical solution method. Then, we synthesized a nanostructured organo-silicon compound from methyl tri-methoxysilane and 3-glycidoxy-propyl-trimethoxy-silane. The transmittance of the organo-silicon compound was found to be over 90% in the wavelength range of 400~1500 nm. Then we prepared a fluoride-based phosphor paste by mixing the organo-silicon compound with Na(Ca)YF4:Yb3+, Er3+. Subsequently, this paste was coated on polyethylene terephthalate, followed by heat-treatment at 120 °C. The visible emission of the infrared detection card was found to be at 655 nm and 661 nm an excitation wavelength of 980 nm.

Kombinasi Calcitriol dan Ethynil Ethyl Estradiol Meningkatkan Ekskresi Kalsium Urin dan Risiko Urolitiasis pada Tikus Ovariektomi

Directory of Open Access Journals (Sweden)

Hartiningsih Hartiningsih

2017-06-01

Full Text Available The high excretion of calcium (Ca in the urine can trigger the formation of urolith. Estrogen and calcitriol decrease urinary Ca excretion. This study aims to examine the combination of calcitriol and ethinyl ethyl estradiol against Ca urinary excretion and urolithiasis risk of ovariectomized rats. Twentyfive female Wistar rats eight weeks old were divided into five groups: i normal control (NK; ii ovariectomized control (OVK; iii ovariectomized + calcitriol (OVD; iv ovariectomized + ethinyl ethyl estradiol (OVE; and v ovariectomized + combination calcitriol and ethinyl ethyl estradiol (OVDE. Seven weeks post-ovariectomy, each rat was put in an individual metabolic cage for the study of Ca balance. At day 4 to 7 of the study, residual feed, urine, and feces were collected daily for Ca analysis. At day 8, the rats were euthanized, the left kidney were collected for histopathological examination. The results showed that combination of calcitriol and ethinyl ethyl estradiol in OVDE rats caused Ca intake and Ca intestinal absorption significantly higher, and urinary Ca excretion tended to be higher although not significantly different compared to OVK rats. Calcium excretion in OVK rat urine was higher compared to the NK rats. The kidney histopathological changes of OVK rats were not different from the NK rats. Histopathological examination of the OVDE group kidney showed protein deposition in the capsular of Bowman’s capsule and proximal tubules, atrophy of the proximal tubules, and necrosis, respectively. It is concluded that the combination of calcitriol with ethinyl ethyl estradiol in ovariectomized rats increased urinary Ca excretion and increased the risk of urolithiasis. ABSTRAK Tingginya ekskresi kalsium (Ca dalam urin dapat menjadi pemicu terbentuknya urolit. Estrogen dan calcitriol menurunkan ekskresi Ca urin. Penelitian ini dilakukan bertujuan untuk mengkaji kombinasi calcitriol dan ethynil ethyl estradiol terhadap ekskresi Ca dalam urin

Liquid phase epitaxial growth of silicon on porous silicon for photovoltaic applications

International Nuclear Information System (INIS)

Berger, S.; Quoizola, S.; Fave, A.; Kaminski, A.; Perichon, S.; Barbier, D.; Laugier, A.

2001-01-01

The aim of this experiment is to grow a thin silicon layer ( 2 atmosphere, and finally LPE silicon growth with different temperature profiles in order to obtain a silicon layer on the sacrificial porous silicon (p-Si). We observed a pyramidal growth on the surface of the (100) porous silicon but the coalescence was difficult to obtain. However, on a p-Si (111) oriented wafer, homogeneous layers were obtained. (orig.)

Higher levels of ethyl paraben and butyl paraben in rat amniotic fluid than in maternal plasma after subcutaneous administration

DEFF Research Database (Denmark)

Frederiksen, Hanne; Taxvig, Camilla; Hass, Ulla

2008-01-01

to obtain more knowledge about the distribution of ethyl paraben and butyl paraben in pregnant rats and pups after perinatal exposure, the presented study was designed. The data show response and distribution of ethyl paraben and butyl paraben in maternal rat plasma, pools of amniotic fluids, placenta......, whole-body fetuses, and in fetal liver after dosing of dams with 100, 200, and 400 mg/kg body weight (bw)/day from gestational day 7 to 21. After cesarean section of dams, the fluids and tissues were collected, deconjugated, and purified by solid-phase extraction, and ethyl paraben and butyl paraben...... were analyzed by liquid chromatography-tandem mass spectrometry. Markedly higher levels of ethyl paraben compared to butyl paraben were found in all fluids and tissues. Both ethyl paraben and butyl paraben in maternal plasma, livers, and whole-body tissues from fetus seemed to be saturated after dosing...

A genome-wide methylation study on obesity Differential variability and differential methylation

NARCIS (Netherlands)

Xu, Xiaojing; Su, Shaoyong; Barnes, Vernon A.; De Miguel, Carmen; Pollock, Jennifer; Ownby, Dennis; Shi, Huidong; Zhu, Haidong; Snieder, Harold; Wang, Xiaoling

2013-01-01

Besides differential methylation, DNA methylation variation has recently been proposed and demonstrated to be a potential contributing factor to cancer risk. Here we aim to examine whether differential variability in methylation is also an important feature of obesity, a typical non-malignant common

Spectrometric Study of the Nitrile-Ketenimines Tautomerism

International Nuclear Information System (INIS)

Cisneros, H.S.; Laurella, S.; Ruiz, D.L.; Ponzinibbio, A.; Allegretti, P.E.; Furlong, J.J.P.

2011-01-01

Mass spectrometry is used to evaluate the occurrence of the nitrile-ketenimines tautomerism. Mass spectra of two differently substituted nitriles, ethyl-4,4-dicyano-3-methyl-3-butenoate and diethyl-2-cyano-3-methyl-2-pentenodiate are examined looking for common mass spectral behaviors. Ion fragmentation assignments for specific tautomers allow to predict the presence of the corresponding structures. Additionally, the mass spectrum and nuclear magnetic resonance spectra of ethyl-4,4-dicyano-2,2-diethyl-3-methyl-3-butenoate and that of the corresponding amination product support the occurrence of the ketenimines tautomer in the equilibrium

Spectrometric Study of the Nitrile-Ketenimine Tautomerism

Directory of Open Access Journals (Sweden)

Hebe Saraví Cisneros

2009-01-01

Full Text Available Mass spectrometry is used to evaluate the occurrence of the nitrile-ketenimine tautomerism. Mass spectra of two differently substituted nitriles, ethyl-4,4-dicyano-3-methyl-3-butenoate and diethyl-2-cyano-3-methyl-2-pentenodiate are examined looking for common mass spectral behaviors. Ion fragmentation assignments for specific tautomers allow to predict the presence of the corresponding structures. Additionally, the mass spectrum and nuclear magnetic resonance spectra of ethyl-4,4-dicyano-2,2-diethyl-3-methyl-3-butenoate and that of the corresponding amination product support the occurrence of the ketenimine tautomer in the equilibrium.

Maternal intake of methyl-group donors affects DNA methylation of metabolic genes in infants.

Science.gov (United States)

Pauwels, Sara; Ghosh, Manosij; Duca, Radu Corneliu; Bekaert, Bram; Freson, Kathleen; Huybrechts, Inge; Langie, Sabine A S; Koppen, Gudrun; Devlieger, Roland; Godderis, Lode

2017-01-01

Maternal nutrition during pregnancy and infant nutrition in the early postnatal period (lactation) are critically involved in the development and health of the newborn infant. The Maternal Nutrition and Offspring's Epigenome (MANOE) study was set up to assess the effect of maternal methyl-group donor intake (choline, betaine, folate, methionine) on infant DNA methylation. Maternal intake of dietary methyl-group donors was assessed using a food-frequency questionnaire (FFQ). Before and during pregnancy, we evaluated maternal methyl-group donor intake through diet and supplementation (folic acid) in relation to gene-specific ( IGF2 DMR, DNMT1 , LEP , RXRA ) buccal epithelial cell DNA methylation in 6 months old infants ( n  = 114) via pyrosequencing. In the early postnatal period, we determined the effect of maternal choline intake during lactation (in mothers who breast-fed for at least 3 months) on gene-specific buccal DNA methylation ( n  = 65). Maternal dietary and supplemental intake of methyl-group donors (folate, betaine, folic acid), only in the periconception period, was associated with buccal cell DNA methylation in genes related to growth ( IGF2 DMR), metabolism ( RXRA ), and appetite control ( LEP ). A negative association was found between maternal folate and folic acid intake before pregnancy and infant LEP (slope = -1.233, 95% CI -2.342; -0.125, p  = 0.0298) and IGF2 DMR methylation (slope = -0.706, 95% CI -1.242; -0.107, p  = 0.0101), respectively. Positive associations were observed for maternal betaine (slope = 0.875, 95% CI 0.118; 1.633, p  = 0.0241) and folate (slope = 0.685, 95% CI 0.245; 1.125, p  = 0.0027) intake before pregnancy and RXRA methylation. Buccal DNMT1 methylation in the infant was negatively associated with maternal methyl-group donor intake in the first and second trimester of pregnancy and negatively in the third trimester. We found no clear association between maternal choline intake

Two new Ni(II) supramolecular complexes based on ethyl isonicotinate and ethyl nicotinate for removal of acid blue 92 dye

Science.gov (United States)

Etaiw, Safaa El-din H.; Marie, Hassan

2018-03-01

Two new luminescent supramolecular complexes (SC); [Ni(EIN)4(NCS)2] SC1 and [Ni2(EN)8(NCS)4] SC2, (EIN = ethyl isonicotinate, EN = ethyl nicotinate), have been synthesized by self-assembly method and structurally characterized by X-ray single crystal, FT-IR and UV-Vis spectra, PXRD, elemental and thermogravimetric analyses. Both SC1 and SC2 are monoclinic crystals however, they have different asymmetric units. Ni(II) atoms in both SC are isostructural and have similar hexa-coordinate environment. The structures of SC1 and SC2 consist of parallel polymeric 1D-chains, extended in two and three dimensional supramolecular frameworks by intermolecular hydrogen bonding interactions. SC1 and SC2 are luminescent materials which can be used in applications as molecular sensing systems. SC1 and SC2 were used as heterogeneous catalysts for degradation of acid blue 92 (AB-92) under sun light irradiation. The fluorescence measurements of terephthalic acid technique as a probe molecule were used to determine the •OH radicals. Also the radicals trapping experiments using isopropanol alcohol (IPA) as radical scavenger were discussed. In addition a mechanism of degradation was proposed and discussed.

Highly nonlinear sub-micron silicon nitride trench waveguide coated with gold nanoparticles

Science.gov (United States)

Huang, Yuewang; Zhao, Qiancheng; Sharac, Nicholas; Ragan, Regina; Boyraz, Ozdal

2015-05-01

We demonstrate the fabrication of a highly nonlinear sub-micron silicon nitride trench waveguide coated with gold nanoparticles for plasmonic enhancement. The average enhancement effect is evaluated by measuring the spectral broadening effect caused by self-phase-modulation. The nonlinear refractive index n2 was measured to be 7.0917×10-19 m2/W for a waveguide whose Wopen is 5 μm. Several waveguides at different locations on one wafer were measured in order to take the randomness of the nanoparticle distribution into consideration. The largest enhancement is measured to be as high as 10 times. Fabrication of this waveguide started with a MEMS grade photomask. By using conventional optical lithography, the wide linewidth was transferred to a wafer. Then the wafer was etched anisotropically by potassium hydroxide (KOH) to engrave trapezoidal trenches with an angle of 54.7º. Side wall roughness was mitigated by KOH etching and thermal oxidation that was used to generate a buffer layer for silicon nitride waveguide. The guiding material silicon nitride was then deposited by low pressure chemical vapor deposition. The waveguide was then patterned with a chemical template, with 20 nm gold particles being chemically attached to the functionalized poly(methyl methacrylate) domains. Since the particles attached only to the PMMA domains, they were confined to localized regions, therefore forcing the nanoparticles into clusters of various numbers and geometries. Experiments reveal that the waveguide has negligible nonlinear absorption loss, and its nonlinear refractive index can be greatly enhanced by gold nano clusters. The silicon nitride trench waveguide has large nonlinear refractive index, rendering itself promising for nonlinear applications.

Eficácia de herbicidas inibidores da ACCase no controle de gramíneas em lavouras de soja Efficacy of ACCase-inhibiting herbicides in controlling grass weeds in soybean crops

Directory of Open Access Journals (Sweden)

A.L.L. Barroso

2010-01-01

Full Text Available Objetivou-se com este trabalho avaliar a eficácia de herbicidas inibidores da ACCase, aplicados isoladamente ou em associações, no controle das espécies de plantas daninhas pertencentes à família das gramíneas Brachiaria decumbens, Digitaria ciliaris, Eleusine indica, Brachiaria plantaginea e Cenchrus echinatus, na cultura da soja. O experimento foi conduzido em campo, em delineamento de blocos ao acaso com quatro repetições. Os tratamentos avaliados foram: clethodim (84 g ha-1, clethodim + quizalofop-p-ethyl (48 + 40 g ha-1, [clethodim + fenoxaprop-p-ethyl] (50 + 50 g ha-1, sethoxydim (230 g ha-1, tepraloxydim (100 g ha-1, fluazifop-p-butyl (125 g ha-1, haloxyfop-methyl (60 g ha-1 e testemunha sem herbicida. A convivência das plantas de soja com as gramíneas infestantes resultou em perda significativa na produtividade de grãos. Os melhores níveis de controle de B. decumbens foram verificados com a utilização de haloxyfop-methyl. Tepraloxydim pode ser considerado seletivo a B. decumbens. Nenhum tratamento proporcionou controle final de D. ciliaris superior a 90%, porém menor eficiência foi verificada quando se aplicaram sethoxydim e fluazifop-p-butyl. Apenas os tratamentos sethoxydim e [clethodim + fenoxaprop-p-ethyl] não mostraram controle satisfatório de E. indica. B. plantaginea foi a espécie mais facilmente controlada pelos herbicidas avaliados; no entanto, haloxyfop-methyl, tepraloxydim, clethodim e [clethodim + fenoxaprop-p-ethyl] se destacaram no controle dessa invasora. A adição de quizalofop-p-ethyl ao clethodim proporcionou incremento significativo no controle de C. echinatus. Também os herbicidas haloxyfop-methyl e tepraloxydim apresentaram controle satisfatório dessa espécie daninha.The objective of this work was to evaluate the efficacy of ACCase-inhibitors (ariloxyfenoxypropionates and cyclohexanodiones, applied alone or in combination, in controlling the grass weed species Brachiaria decumbens, Digitaria

Protein methylation in pea chloroplasts

International Nuclear Information System (INIS)

Niemi, K.J.; Adler, J.; Selman, B.R.

1990-01-01

The methylation of chloroplast proteins has been investigated by incubating intact pea (Pisum sativum) chloroplasts with [ 3 H-methyl]-S-adenosylmethionine. Incubation in the light increases the amount of methylation in both the thylakoid and stromal fractions. Numerous thylakoid proteins serve as substrates for the methyltransfer reactions. Three of these thylakoid proteins are methylated to a significantly greater extent in the light than in the dark. The primary stromal polypeptide methylated is the large subunit of ribulose bisphosphate carboxylase/oxygenase. One other stromal polypeptide is also methylated much more in the light than in the dark. Two distinct types of protein methylation occur. One methylinkage is stable to basic conditions whereas a second type is base labile. The base-stable linkage is indicative of N-methylation of amino acid residues while base-lability is suggestive of carboxymethylation of amino acid residues. Labeling in the light increases the percentage of methylation that is base labile in the thylakoid fraction while no difference is observed in the amount of base-labile methylations in light-labeled and dark-labeled stromal proteins. Also suggestive of carboxymethylation is the detection of volatile [ 3 H]methyl radioactivity which increases during the labeling period and is greater in chloroplasts labeled in the light as opposed to being labeled in the dark; this implies in vivo turnover of the [ 3 H]methyl group

Synthesis and Characterization of the Most Active Copper ATRP Catalyst Based on Tris[(4-dimethylaminopyridyl)methyl]amine.

Science.gov (United States)

Ribelli, Thomas G; Fantin, Marco; Daran, Jean-Claude; Augustine, Kyle F; Poli, Rinaldo; Matyjaszewski, Krzysztof

2018-01-31

The tris[(4-dimethylaminopyridyl)methyl]amine (TPMA NMe2 ) as a ligand for copper-catalyzed atom transfer radical polymerization (ATRP) is reported. In solution, the [Cu I (TPMA NMe2 )Br] complex shows fluxionality by variable-temperature NMR, indicating rapid ligand exchange. In the solid state, the [Cu II (TPMA NMe2 )Br][Br] complex exhibits a slightly distorted trigonal bipyramidal geometry (τ = 0.89). The UV-vis spectrum of [Cu II (TPMA NMe2 )Br] + salts is similar to those of other pyridine-based ATRP catalysts. Electrochemical studies of [Cu(TPMA NMe2 )] 2+ and [Cu(TPMA NMe2 )Br] + showed highly negative redox potentials (E 1/2 = -302 and -554 mV vs SCE, respectively), suggesting unprecedented ATRP catalytic activity. Cyclic voltammetry (CV) in the presence of methyl 2-bromopropionate (MBrP; acrylate mimic) was used to determine activation rate constant k a = 1.1 × 10 6 M -1 s -1 , confirming the extremely high catalyst reactivity. In the presence of the more active ethyl α-bromoisobutyrate (EBiB; methacrylate mimic), total catalysis was observed and an activation rate constant k a = 7.2 × 10 6 M -1 s -1 was calculated with values of K ATRP ≈ 1. ATRP of methyl acrylate showed a well-controlled polymerization using as little as 10 ppm of catalyst relative to monomer, while side reactions such as Cu I -catalyzed radical termination (CRT) could be suppressed due to the low concentration of L/Cu I at a steady state.

Characterization and Antioxidant Properties of Six Algerian Propolis Extracts: Ethyl Acetate Extracts Inhibit Myeloperoxidase Activity

Directory of Open Access Journals (Sweden)

Yasmina Mokhtaria Boufadi

2014-02-01

Full Text Available Because propolis contains many types of antioxidant compounds such as polyphenols and flavonoids, it can be useful in preventing oxidative damages. Ethyl acetate extracts of propolis from several Algerian regions show high activity by scavenging free radicals, preventing lipid peroxidation and inhibiting myeloperoxidase (MPO. By fractioning and assaying ethyl acetate extracts, it was observed that both polyphenols and flavonoids contribute to these activities. A correlation was observed between the polyphenol content and the MPO inhibition. However, it seems that kaempferol, a flavonoid, contributes mainly to the MPO inhibition. This molecule is in a high amount in the ethyl acetate extract and demonstrates the best efficiency towards the enzyme with an inhibiting concentration at 50% of 4 ± 2 µM.

Mouthwash overdose

Science.gov (United States)

... are: Chlorhexidine gluconate Ethanol (ethyl alcohol) Hydrogen peroxide Methyl salicylate ... amounts of alcohol (drunkenness). Swallowing large amounts of methyl salicylate and hydrogen peroxide may also cause serious stomach ...

CH(3)NH(3)PbI(3) perovskite / silicon tandem solar cells: characterization based optical simulations.

Science.gov (United States)

Filipič, Miha; Löper, Philipp; Niesen, Bjoern; De Wolf, Stefaan; Krč, Janez; Ballif, Christophe; Topič, Marko

2015-04-06

In this study we analyze and discuss the optical properties of various tandem architectures: mechanically stacked (four-terminal) and monolithically integrated (two-terminal) tandem devices, consisting of a methyl ammonium lead triiodide (CH(3)NH(3)PbI(3)) perovskite top solar cell and a crystalline silicon bottom solar cell. We provide layer thickness optimization guidelines and give estimates of the maximum tandem efficiencies based on state-of-the-art sub cells. We use experimental complex refractive index spectra for all involved materials as input data for an in-house developed optical simulator CROWM. Our characterization based simulations forecast that with optimized layer thicknesses the four-terminal configuration enables efficiencies over 30%, well above the current single-junction crystalline silicon cell record of 25.6%. Efficiencies over 30% can also be achieved with a two-terminal monolithic integration of the sub-cells, combined with proper selection of layer thicknesses.

Multicomponent Synthesis of a N-Protected Alpha-Amino Ester: Ethyl 2-((4-Methoxyphenyl)Amino)-3-Phenylpropanoate

Science.gov (United States)

Le Gall, Erwan; Pignon, Antoine

2012-01-01

This laboratory experiment describes the preparation of a N-protected phenylalanine ethyl ester by a zinc-mediated Mannich-like multicomponent reaction between benzyl bromide, "p"-anisidine, and ethyl glyoxylate. The one-step reaction involves the in situ metallation of benzyl bromide into a benzylzinc reagent and its addition onto imine (Barbier…

Nonlinear silicon photonics

Science.gov (United States)

Borghi, M.; Castellan, C.; Signorini, S.; Trenti, A.; Pavesi, L.

2017-09-01

Silicon photonics is a technology based on fabricating integrated optical circuits by using the same paradigms as the dominant electronics industry. After twenty years of fervid development, silicon photonics is entering the market with low cost, high performance and mass-manufacturable optical devices. Until now, most silicon photonic devices have been based on linear optical effects, despite the many phenomenologies associated with nonlinear optics in both bulk materials and integrated waveguides. Silicon and silicon-based materials have strong optical nonlinearities which are enhanced in integrated devices by the small cross-section of the high-index contrast silicon waveguides or photonic crystals. Here the photons are made to strongly interact with the medium where they propagate. This is the central argument of nonlinear silicon photonics. It is the aim of this review to describe the state-of-the-art in the field. Starting from the basic nonlinearities in a silicon waveguide or in optical resonator geometries, many phenomena and applications are described—including frequency generation, frequency conversion, frequency-comb generation, supercontinuum generation, soliton formation, temporal imaging and time lensing, Raman lasing, and comb spectroscopy. Emerging quantum photonics applications, such as entangled photon sources, heralded single-photon sources and integrated quantum photonic circuits are also addressed at the end of this review.

Transformational silicon electronics

KAUST Repository

Rojas, Jhonathan Prieto

2014-02-25

In today\\'s traditional electronics such as in computers or in mobile phones, billions of high-performance, ultra-low-power devices are neatly integrated in extremely compact areas on rigid and brittle but low-cost bulk monocrystalline silicon (100) wafers. Ninety percent of global electronics are made up of silicon. Therefore, we have developed a generic low-cost regenerative batch fabrication process to transform such wafers full of devices into thin (5 μm), mechanically flexible, optically semitransparent silicon fabric with devices, then recycling the remaining wafer to generate multiple silicon fabric with chips and devices, ensuring low-cost and optimal utilization of the whole substrate. We show monocrystalline, amorphous, and polycrystalline silicon and silicon dioxide fabric, all from low-cost bulk silicon (100) wafers with the semiconductor industry\\'s most advanced high-κ/metal gate stack based high-performance, ultra-low-power capacitors, field effect transistors, energy harvesters, and storage to emphasize the effectiveness and versatility of this process to transform traditional electronics into flexible and semitransparent ones for multipurpose applications. © 2014 American Chemical Society.

Silicon Microspheres Photonics

International Nuclear Information System (INIS)

Serpenguzel, A.

2008-01-01

Electrophotonic integrated circuits (EPICs), or alternatively, optoelectronic integrated circuit (OEICs) are the natural evolution of the microelectronic integrated circuit (IC) with the addition of photonic capabilities. Traditionally, the IC industry has been based on group IV silicon, whereas the photonics industry on group III-V semiconductors. However, silicon based photonic microdevices have been making strands in siliconizing photonics. Silicon microspheres with their high quality factor whispering gallery modes (WGMs), are ideal candidates for wavelength division multiplexing (WDM) applications in the standard near-infrared communication bands. In this work, we will discuss the possibility of using silicon microspheres for photonics applications in the near-infrared

Fluorinated benzamide neuroleptics--III. Development of (S)-N-[(1-allyl-2-pyrrolidinyl)methyl]-5-(3-[{sup 18}F]fluoropropyl)-2,3- dimethoxybenzamide as an improved dopamine D-2 receptor tracer