Melon oil methyl ester: an environmentally friendly fuel

Directory of Open Access Journals (Sweden)

S.K. Fasogbon

2015-06-01

Full Text Available Demand for energy is growing across the globe due to the direct relationship between the well-being and prosperity of people and energy usage. However, meeting this growing energy demand in a safe and environmentally friendly manner is a key challenge. To this end, methyl esters (biodiesels have been and are being widely investigated as alternatives to fossil fuels in compression ignition engines. In this study, melon (Colocynthis Citrullus Lanatus oil was used to synthesize biodiesel (methyl ester using the transesterification method in the presence of a sodium hydroxide promoter. The emissions profile of the biodiesel was investigated by setting up a single-cylinder four-stroke air-cooled CI engine connected to a TD115-hydraulic dynamometer and an Eclipse Flue Gas Analyzer (FGA with model number EGA4 flue gas analyzer. The engine was run at engine speeds of 675, 1200 and 1900rpm for biodiesel/diesel blends at 21°C on a volume basis of 0/100(B0, 10/90(B10, 20/80(B20, 30/70(B30, 40/60(B40 and 50/50(B50. The test showed a downward trend in the emissions profile of the biodiesel, with remarkable reductions of about 55% in the dangerous-carbon monoxide exhaust gas pollutant and 33.3% in the unfriendly SOX from 100% diesel to B30-biodiesel concentration. Increasing the speed from 675 to 1200 and then to 1900 rpm also afforded further reductions in CO and SOX exhaust emissions. NOX however increased marginally by 2.1% from the same 100% diesel to the B30-biodiesel composition. Based on the remarkable reduction in CO and SOX and the marginal increase in NOX as the concentration of the biodiesel increased in the blends, the study concludes that melon oil methyl ester is an environmentally friendly fuel.

Comparison of GC stationary phases for the separation of fatty acid methyl esters in biodiesel fuels.

Science.gov (United States)

Goding, Julian C; Ragon, Dorisanne Y; O'Connor, Jack B; Boehm, Sarah J; Hupp, Amber M

2013-07-01

The fatty acid methyl ester (FAME) content of biodiesel fuels has traditionally been determined using gas chromatography with a polar stationary phase. In this study, a direct comparison of the separation of FAMEs present in various biodiesel samples on three polar stationary phases and one moderately polar stationary phase (with comparable column dimensions) was performed. Retention on each column was based on solubility in and polarity of the phase. Quantitative metrics describing the resolution of important FAME pairs indicate high resolution on all polar columns, yet the best resolution, particularly of geometric isomers, is achieved on the cyanopropyl column. In addition, the separation of four C18 monounsaturated isomers was optimized and the elution order determined on each column. FAME composition of various biodiesel fuel types was determined on each column to illustrate (1) chemical differences in biodiesels produced from different feedstocks and (2) chemical similarities in biodiesels of the same feedstock type produced in different locations and harvest seasons.

Critical aggregates concentration of fatty esters present in biodiesel determined by turbidity and fluorescence.

Science.gov (United States)

Froehner, Sandro; Sánez, Juan; Dombroski, Luiz Fernando; Gracioto, Maria Paula

2017-09-01

Biodiesel for combustible engine is available as mixture of fossil diesel and fatty esters obtained by transesterification of vegetable oils. The use of biodiesel reduces the amount of SO x , mainly. However, it was already observed that biodiesel has a different behavior in environment in cases of accidental spill and groundwater contamination. It was noticed that the biodegradation of hydrocarbons (cyclic and aliphatic) in the presence of biodiesel are speeded, although the mechanism is still unclear. Considering the chemical structure of fatty esters, it was investigated the formation of aggregates in water solution by fatty esters present in commercial biodiesel. In Brazil, biodiesel is composed by 95% of fossil diesel and 5% of fatty esters mixture. In this work, fatty esters were treated as neutral surfactant, i.e., it was treated as a molecule with polar and non-polar part. Turbidity and fluorescence were used to determine the critical aggregates concentration (CAC). Water solutions containing fatty esters were examined exploiting changes in turbidity and fluorescence intensity of pyrene. Abrupt changes were attributed to aggregates formation, following the same behavior of traditional amphiphilic compounds. It was determined the CAC for ethyl palmitate, ethyl stearate, ethyl oleate, and ethyl linoleate. The values of CAC for fatty esters varied from 1.91 to 4.27 μmol/L, while CAC for the mixture of esters (biodiesel) was 2.01 for methyl esters and 1.19 for ethyl esters, both prepared using soybean oil. The aggregates formation was also determined by fluorescence measurements considering the changes in intensity of peaks I and III of pyrene. Pyrene senses the changes in environment polarity. The values found of CAC by fluorescence for individual ethyl esters varied from 1.85 to 3.21 μmol/L, while mixtures of ethyl esters was 2.23 and 2.07 μmol/L for mixture of methyl esters. The results clearly showed that fatty esters form aggregates and might be

A monolithic lipase reactor for biodiesel production by transesterification of triacylglycerides into fatty acid methyl esters

KAUST Repository

Urban, Jiří T.

2011-09-26

An enzymatic reactor with lipase immobilized on a monolithic polymer support has been prepared and used to catalyze the transesterification of triacylglycerides into the fatty acid methyl esters commonly used for biodiesel. A design of experiments procedure was used to optimize the monolithic reactor with variables including control of the surface polarity of the monolith via variations in the length of the hydrocarbon chain in alkyl methacrylate monomer, time of grafting of 1-vinyl-4,4-dimethylazlactone used to activate the monolith, and time used for the immobilization of porcine lipase. Optimal conditions involved the use of a poly(stearyl methacrylate-co-ethylene dimethacrylate) monolith, grafted first with vinylazlactone, then treated with lipase for 2h to carry out the immobilization of the enzyme. Best conditions for the transesterification of glyceryl tributyrate included a temperature of 37°C and a 10min residence time of the substrate in the bioreactor. The reactor did not lose its activity even after pumping through it a solution of substrate equaling 1,000 reactor volumes. This enzymatic reactor was also used for the transesterification of triacylglycerides from soybean oil to fatty acid methyl esters thus demonstrating the ability of the reactor to produce biodiesel. © 2011 Wiley Periodicals, Inc.

A monolithic lipase reactor for biodiesel production by transesterification of triacylglycerides into fatty acid methyl esters

KAUST Repository

Urban, Jiří T.; Švec, František; Frechet, Jean

2011-01-01

An enzymatic reactor with lipase immobilized on a monolithic polymer support has been prepared and used to catalyze the transesterification of triacylglycerides into the fatty acid methyl esters commonly used for biodiesel. A design of experiments procedure was used to optimize the monolithic reactor with variables including control of the surface polarity of the monolith via variations in the length of the hydrocarbon chain in alkyl methacrylate monomer, time of grafting of 1-vinyl-4,4-dimethylazlactone used to activate the monolith, and time used for the immobilization of porcine lipase. Optimal conditions involved the use of a poly(stearyl methacrylate-co-ethylene dimethacrylate) monolith, grafted first with vinylazlactone, then treated with lipase for 2h to carry out the immobilization of the enzyme. Best conditions for the transesterification of glyceryl tributyrate included a temperature of 37°C and a 10min residence time of the substrate in the bioreactor. The reactor did not lose its activity even after pumping through it a solution of substrate equaling 1,000 reactor volumes. This enzymatic reactor was also used for the transesterification of triacylglycerides from soybean oil to fatty acid methyl esters thus demonstrating the ability of the reactor to produce biodiesel. © 2011 Wiley Periodicals, Inc.

A monolithic lipase reactor for biodiesel production by transesterification of triacylglycerides into fatty acid methyl esters.

Science.gov (United States)

Urban, Jiri; Svec, Frantisek; Fréchet, Jean M J

2012-02-01

An enzymatic reactor with lipase immobilized on a monolithic polymer support has been prepared and used to catalyze the transesterification of triacylglycerides into the fatty acid methyl esters commonly used for biodiesel. A design of experiments procedure was used to optimize the monolithic reactor with variables including control of the surface polarity of the monolith via variations in the length of the hydrocarbon chain in alkyl methacrylate monomer, time of grafting of 1-vinyl-4,4-dimethylazlactone used to activate the monolith, and time used for the immobilization of porcine lipase. Optimal conditions involved the use of a poly(stearyl methacrylate-co-ethylene dimethacrylate) monolith, grafted first with vinylazlactone, then treated with lipase for 2 h to carry out the immobilization of the enzyme. Best conditions for the transesterification of glyceryl tributyrate included a temperature of 37°C and a 10 min residence time of the substrate in the bioreactor. The reactor did not lose its activity even after pumping through it a solution of substrate equaling 1,000 reactor volumes. This enzymatic reactor was also used for the transesterification of triacylglycerides from soybean oil to fatty acid methyl esters thus demonstrating the ability of the reactor to produce biodiesel. Copyright © 2011 Wiley Periodicals, Inc.

Mitigating crystallization of saturated FAMES (fatty acid methyl esters) in biodiesel: 4. The phase behavior of 1,3-dioleoyl-2-palmitoyl glycerol – Methyl stearate binary system

International Nuclear Information System (INIS)

Mohanan, Athira; Bouzidi, Laziz; Narine, Suresh S.

2016-01-01

The present study examines the phase behavior of a model binary system made of OPO (1,3-dioleoyl-2-palmitoyl glycerol); a TAG (triacylglycerol) highly effective in depressing onset of crystallization of biodiesel, and MeS (methyl stearate); a prevalent saturated FAMEs (fatty acid methyl esters) in biodiesel. The thermal behavior, crystal structure and microstructure of the OPO/MeS mixtures were investigated with DSC (differential scanning calorimetry), XRD (X-ray diffraction) and PLM (polarized light microscope). The OPO/MeS system presented a phase diagram with peritectic and eutectic transitions. A simple thermodynamic modeling of the liquidus line indicated a relatively complex mixing behavior, and highlighted the prevailing effect of the peritectic compound on solubility. Different types of microstructures that were more or less influenced by MeS, OPO or/and compound microstructures were observed in the mixtures. They are associated with the crystal phases and the thermal transitions. Furthermore, MeS, OPO and compound crystal structures (monoclinic, orthorhombic and triclinic, respectively) served as templates for the crystal forms of the coexisting phases. The singularities in the liquidus line are attributed to chain length mismatch between the palmitic acid and the FAME (fatty acid methyl ester). The phase diagram achieved for OPO/MeS system is complete and can help in designing additive formulations to improve the cold flow behavior of biodiesel. - Highlights: • 1,3-dioleoyl-2-palmitoyl glycerol/methyl stearate (OPO/MeS) studied in detail. • Phase diagram with thermal transitions, polymorphism, microstructure achieved. • Phase trajectory singularities attributed to length mismatch of linear chains. • Mechanism for disruption of crystallization of biodiesel evidenced and explained.

Density of Jatropha curcas Seed Oil and its Methyl Esters: Measurement and Estimations

Science.gov (United States)

Veny, Harumi; Baroutian, Saeid; Aroua, Mohamed Kheireddine; Hasan, Masitah; Raman, Abdul Aziz; Sulaiman, Nik Meriam Nik

2009-04-01

Density data as a function of temperature have been measured for Jatropha curcas seed oil, as well as biodiesel jatropha methyl esters at temperatures from above their melting points to 90 ° C. The data obtained were used to validate the method proposed by Spencer and Danner using a modified Rackett equation. The experimental and estimated density values using the modified Rackett equation gave almost identical values with average absolute percent deviations less than 0.03% for the jatropha oil and 0.04% for the jatropha methyl esters. The Janarthanan empirical equation was also employed to predict jatropha biodiesel densities. This equation performed equally well with average absolute percent deviations within 0.05%. Two simple linear equations for densities of jatropha oil and its methyl esters are also proposed in this study.

Experimental and numerical investigations on spray characteristics of fatty acid methyl esters.

Science.gov (United States)

Lanjekar, R D; Deshmukh, D

2018-02-01

A comparative experimental and numerical study is conducted to establish the significance of the use of single-component over multi-component representatives of biodiesel, diesel and their blend for predicting spray tip penetration. Methyl oleate and methyl laurate are used as single-component representative fuels for biodiesel. The pure components n -heptane, n -dodecane and n -tetradecane are used as single-component representative fuels for diesel. Methyl laurate is found to represent biodiesel of coconut, whereas methyl oleate is found to represent biodiesel having high percentage of long-chain fatty acid esters. The spray tip penetration of methyl oleate is found to be in good agreement with the measured spray tip penetration of karanja biodiesel. The spray tip penetration prediction of n -heptane fuel is closely following diesel spray tip penetration along with that of n -tetradecane and n -dodecane. The study suggests that the knowledge of the single-component representatives of biodiesel, diesel and their blend is sufficient to predict the spray tip penetration of the corresponding biodiesel, diesel and their blend under non-evaporating environment.

Experimental and numerical investigations on spray characteristics of fatty acid methyl esters

Science.gov (United States)

Lanjekar, R. D.; Deshmukh, D.

2018-02-01

A comparative experimental and numerical study is conducted to establish the significance of the use of single-component over multi-component representatives of biodiesel, diesel and their blend for predicting spray tip penetration. Methyl oleate and methyl laurate are used as single-component representative fuels for biodiesel. The pure components n-heptane, n-dodecane and n-tetradecane are used as single-component representative fuels for diesel. Methyl laurate is found to represent biodiesel of coconut, whereas methyl oleate is found to represent biodiesel having high percentage of long-chain fatty acid esters. The spray tip penetration of methyl oleate is found to be in good agreement with the measured spray tip penetration of karanja biodiesel. The spray tip penetration prediction of n-heptane fuel is closely following diesel spray tip penetration along with that of n-tetradecane and n-dodecane. The study suggests that the knowledge of the single-component representatives of biodiesel, diesel and their blend is sufficient to predict the spray tip penetration of the corresponding biodiesel, diesel and their blend under non-evaporating environment.

Biodiesel production via non-catalytic SCF method and biodiesel fuel characteristics

International Nuclear Information System (INIS)

Demirbas, Ayhan

2006-01-01

Vegetable oil (m)ethyl esters, commonly referred to as 'biodiesel,' are prominent candidates as alternative Diesel fuels. Biodiesel is technically competitive with or offers technical advantages compared to conventional petroleum Diesel fuel. The vegetable oils, as alternative engine fuels, are all extremely viscous with viscosities ranging from 10 to 20 times greater than that of petroleum Diesel fuel. The purpose of the transesterification process is to lower the viscosity of the oil. Transesterifications of vegetable oils in supercritical methanol are performed without using any catalyst. The most important variables affecting the methyl ester yield during the transesterification reaction are the molar ratio of alcohol to vegetable oil and the reaction temperature. Biodiesel has become more attractive recently because of its environmental benefits. The cost of biodiesel, however, is the main obstacle to commercialization of the product. With cooking oils used as raw material, the viability of a continuous transesterification process and recovery of high quality glycerol as a biodiesel by product are primary options to be considered to lower the cost of biodiesel. Supercritical methanol has a high potential for both transesterification of triglycerides and methyl esterification of free fatty acids to methyl esters for a Diesel fuel substitute. In the supercritical methanol transesterification method, the yield of conversion increases to 95% in 10 min. The viscosity values of vegetable oils are between 27.2 and 53.6 mm 2 /s, whereas those of vegetable oil methyl esters are between 3.59 and 4.63 mm 2 /s. The flash point values of vegetable oil methyl esters are much lower than those of vegetable oils. An increase in density from 860 to 885 kg/m 3 for vegetable oil methyl esters or biodiesels increases the viscosity from 3.59 to 4.63 mm 2 /s. Biodiesel is an environmentally friendly fuel that can be used in any Diesel engine without modification

Emissions from diesel engines using fatty acid methyl esters from different vegetable oils as blends and pure fuel

International Nuclear Information System (INIS)

Schröder, O; Munack, A; Schaak, J; Pabst, C; Schmidt, L; Bünger, J; Krahl, J

2012-01-01

Biodiesel is used as a neat fuel as well as in blends with mineral diesel fuel. Because of the limited availability of fossil resources, an increase of biogenic compounds in fuels is desired. To achieve this goal, next to rapeseed oil, other sustainably produced vegetable oils can be used as raw materials. These raw materials influence the fuel properties as well as the emissions. To investigate the environmental impact of the exhaust gas, it is necessary to determine regulated and non-regulated exhaust gas components. In detail, emissions of aldehydes and polycyclic aromatic hydrocarbons (PAH), as well as mutagenicity in the Ames test are of special interest. In this paper emission measurements on a Euro III engine OM 906 of Mercedes-Benz are presented. As fuel vegetable oil methyl esters from various sources and reference diesel fuel were used as well as blends of the vegetable oil methyl esters with diesel fuel. PAH were sampled according to VDI Guideline 3872. The sampling procedure of carbonyls was accomplished using DNPH cartridges coupled with potassium iodide cartridges. The carbon monoxide and hydrocarbon emissions of the tested methyl esters show advantages over DF. The particle mass emissions of methyl esters were likewise lower than those of DF, only linseed oil methyl ester showed higher particle mass emissions. A disadvantage is the use of biodiesel with respect to emissions of nitrogen oxides. They increased depending on the type of methyl ester by 10% to 30%. Emissions of polycyclic aromatic hydrocarbons (PAHs) and the results of mutagenicity tests correlate with those of the PM measurements, at which for palm oil methyl ester next to coconut oil methyl ester the lowest emissions were detected. From these results one can formulate a clear link between the iodine number of the ester and the emission behaviour. For blends of biodiesel and diesel fuel, emissions changed linearly with the proportion of biodiesel. However, especially in the non

Influence of fuel injection pressures on Calophyllum inophyllum methyl ester fuelled direct injection diesel engine

International Nuclear Information System (INIS)

Nanthagopal, K.; Ashok, B.; Karuppa Raj, R. Thundil

2016-01-01

Highlights: • Effect of injection pressure of Calophyllum inophyllum biodiesel is investigated. • Engine characteristics of 100% Calophyllum inophyllum biodiesel has been performed. • Calophyllum inophyllum is a non-edible source for biodiesel production. • Increase in injection pressure of biodiesel, improves the fuel economy. • Incylinder pressure characteristics of biodiesel follows similar trend as of diesel. - Abstract: The trend of using biodiesels in compression ignition engines have been the focus in recent decades due to the promising environmental factors and depletion of fossil fuel reserves. This work presents the effect of Calophyllum inophyllum methyl ester on diesel engine performance, emission and combustion characteristics at different injection pressures. Experimental investigations with varying injection pressures of 200 bar, 220 bar and 240 bar have been carried out to analyse the parameters like brake thermal efficiency, specific fuel consumption, heat release rate and engine emissions of direct injection diesel engine fuelled with 100% biodiesel and compared with neat diesel. The experimental results revealed that brake specific fuel consumption of C. inophyllum methyl ester fuelled engine has been reduced to a great extent with higher injection pressure. Significant reduction in emissions of unburnt hydrocarbons, carbon monoxide and smoke opacity have been observed during fuel injection of biodiesel at 220 bar compared to other fuel injection pressures. However oxides of nitrogen increased with increase in injection pressures of C. inophyllum methyl ester and are always higher than that of neat diesel. In addition the combustion characteristics of biodiesel at all injection pressures followed a similar trend to that of conventional diesel.

Synthesis and Characterization of Fatty Acid Methyl Ester by In-Situ Transesterification in Capparis Deciduas Seed

Directory of Open Access Journals (Sweden)

Prasad E FUNDE

2008-12-01

Full Text Available (FAME Fatty acid methyl ester is made virgin or used vegetable oils (both edible and non-edible and animal fats. Fatty acid methyl ester operates in compression ignition engines like petro-diesel. Fatty acid methyl ester can be blended in any ratio with petroleum diesel fuels. It can be stored just like the petroleum diesel fuel. Petrodiesel can be replaced by biodiesel due to its superiority. It has various advantages. The seeds of Capparis deciduas are found to contain non-edible oil in the range of about 63.75 %. The percentage of biodiesel yield increases with concentration of KOH as a catalyst. The aim of this article is to demonstrate the cost effective new source of energy by single step reaction i.e. production of oil by combining extraction and reaction of extract with the mixture of alcohols. In this article the effect of catalyst concentration, time, water content and temperature on in-situ transesterification is studied to obtain optimum yield and Fatty acid methyl ester (Biodiesel Fuel characterization tests show the striking similarity of various physical & chemical properties and campers to ASTM standards.

Methyl and ethyl soybean esters production

Energy Technology Data Exchange (ETDEWEB)

Pighinelli, Anna Leticia Montenegro Turtelli; Park, Kil Jin; Zorzeto, Thais Queiroz [Universidade Estadual de Campinas (FEAGRI/UNICAMP), SP (Brazil). Fac. de Engenharia Agricola], E-mail: annalets@feagri.unicamp.br; Bevilaqua, Gabriela [Universidade Estadual de Campinas (IQ/UNICAMP), SP (Brazil). Inst. de Quimica

2008-07-01

Biodiesel is a fuel obtained from triglycerides found in nature, like vegetable oils and animal fats. Nowadays it has been the subject of many researches impulses by the creation of the Brazilian law that determined the blend of 2% of biodiesel with petrodiesel. Basically, there are no limitations on the oilseed type for chemical reaction, but due to high cost of this major feedstock, it is important to use the grain that is available in the region of production. Soybean is the oilseed mostly produced in Brazil and its oil is the only one that is available in enough quantity to supply the current biodiesel demand. The objective of this work was to study the effects of reaction time and temperature on soybean oil transesterification reaction with ethanol and methanol. A central composite experimental design with five variation levels was used and response surface methodology applied for the data analysis. The statistical analysis of the results showed that none of the factors affected the ethyl esters production. However, the methyl esters production suffered the influence of temperature (linear effect), reaction time (linear and quadratic) and interaction of these two variables. None of the generated models showed significant regression consequently it was not possible to build the response surface. The experiments demonstrated that methanol is the best alcohol for transesterification reactions and the ester yield was up to 85%. (author)

Experimental assessment of toxic phorbol ester in oil, biodiesel and seed cake of Jatropha curcas and use of biodiesel in diesel engine

International Nuclear Information System (INIS)

Prasad, Lalit; Pradhan, Subhalaxmi; Das, L.M.; Naik, S.N.

2012-01-01

Highlights: ► In the present study toxic phorbol esters were detected in oil and seed cake of Jatropha curcas but not detected in biodiesel using high performance liquid chromatography (HPLC). ► The quantity of phorbol esters in Jatropha curcas oil and cake were amounted to be 2.12 ± 0.02 mg/g and 0.6 ± 0.01 mg/g respectively. ► As jatropha oil is a potential source for biodiesel preparation, huge amount of oil and cake will be generated and hence need to be handled carefully. ► Upon engine study exhaust pollutant such as hydrocarbon, smoke opacity and carbon monoxide reduced substantially. - Abstract: The present study deals with estimation of toxic phorbol esters in Jatropha curcas oil, cake and biodiesel and performance emission of different blends of biodiesel in diesel engine. The jatropha seed was collected from Chattishgarh, India and oil content of the seed kernel was 56.5%, determined by soxhlet apparatus. The oil was subjected to biodiesel preparation by twin step method of acid esterification followed by alkali transesterification. The total conversion of jatropha oil methyl ester (JOME) after reaction was 96.05% from proton nuclear magnetic resonance ( 1 H NMR) studies. The phorbol esters content of oil, cake and biodiesel was determined by high performance liquid chromatography (HPLC, Waters). The phorbol esters content of the oil was more (2.26 ± 0.01 mg/g) than the cake (0.6 ± 0.01 mg/g) but no phorbol esters peak was detected in biodiesel. The performance and emission study of the fuel blends (JB2, JB5 and JB10) with conventional diesel were tested for their use as substitute fuel for a single cylinder direct injection diesel engine at constant speed (1500 rpm). The emissions such as CO, HC and smoke opacity decreased whereas NO x and BSCF increased with biodiesel blends.

Effects of antioxidant additives on exhaust emissions reduction in compression ignition engine fueled with methyl ester of annona oil

Directory of Open Access Journals (Sweden)

Ramalingam Senthil

2016-01-01

Full Text Available In this present study, biodiesel is a cleaner burning alternative fuel to the Neat diesel fuel. However, several studies are pointed out that increase in NOx emission for biodiesel when compared with the Neat diesel fuel. The aim of the present study is to analyze the effect of antioxidant (p-phenylenediamine on engine emissions of a Diesel engine fuelled with methyl ester of annona oil. The antioxidant is mixed in various concentrations (0.010 to 0.040% (w/w with methyl ester of annona oil. Result shows that antioxidant additive mixture (MEAO+P200 is effective in control of NOx and HC emission of methyl ester of annona oil fuelled engine without doing any engine modification.

Mitigating crystallization of saturated FAMEs (fatty acid methyl esters) in biodiesel: 2. The phase behavior of 2-stearoyl diolein–methyl stearate binary system

International Nuclear Information System (INIS)

Baker, Mark; Bouzidi, Laziz; Narine, Suresh S.

2015-01-01

The phase behavior of a model binary system made of OSO (2-stearoyl diolein) and MeS (methyl stearate) was investigated with differential scanning calorimetry and X-ray diffraction. The study is part of a series of investigations of unconventional additives such as TAGs (triacylglycerols) and dimers of TAGs with a demonstrated potential to significantly alter the crystallization of biodiesel. The TAG (triacylglycerol) was found to be effective in depressing the crystallization onset of the FAME (fatty acid methyl ester) significantly even at low concentration. OSO was shown to affect the crystallization of the mixtures strongly, and to dramatically alter their polymorphism. The system's phase diagram involved marked transformation lines including eutectics and solid–solid transitions. The molecular interactions were evaluated using a simple thermodynamic model. A mechanism for disruption of crystallization was proposed to be dependent on the peculiar geometry of OSO: the “straight” stearic acid participates easily in the lamellar packing of the equally “straight” FAME, whilst its kinked oleic acids effectively halt additional saturated FAMEs from participating due to steric hindrances. The findings of the study indicate that judicious loadings of TAGs which would target biodiesel's saturated FAMEs will have a substantial beneficial effect on the low temperature performance of the fuel. - Highlights: • 2-Steroyl diolein/methyl stearate (OSO/MeS) binary system investigated comprehensively. • OSO/MeS mixtures presented very complex phase trajectories and behavior. • OSO alters crystallization at both nucleation and growth stages profoundly. • Mechanism for disruption of crystallization proposed and verified. • OSO and homologues formulations can be effectives cold flow additives for biodiesel

Ethylic or methylic route to soybean biodiesel? Tracking environmental answers through life cycle assessment

International Nuclear Information System (INIS)

Alejos Altamirano, Carlos Alberto; Yokoyama, Lídia; Medeiros, José Luiz de; Queiroz Fernandes Araújo, Ofélia de

2016-01-01

Highlights: • Life cycle of biodiesel using alternative transesterification routes is analyzed. • Bioethanol can potentially decrease CO_2 emissions of methanol biodiesel. • Contrarily, equivalent CO_2 emissions are retained and renewability is reduced. • Water footprint increases from 37.12 (methanol) to 44.88 m"3/GJ biodiesel (ethanol). • Energy efficiency is reduced from 79.37% (methanol) to 75.19 (ethanol %). - Abstract: Biodiesel is a renewable fuel produced by transesterification of triacylglicerides (TAG) contained in vegetable oils and animal fats, to yield alkyl esters (biodiesel) and glycerin. Methanol is the main transesterification agent employed resulting in FAME (fatty acid methyl esters), which is primarily obtained from natural gas reforming (fossil source). Substitution of methanol by ethanol produces FAEE (fatty acid ethyl esters) and has the potential to render biodiesel a fully renewable fuel. Although renewability is a significant driving force for the proposed alcohol replacement, environmental performance of the alternative transesterification is questioned. The answer is herein sought through a comparative Life Cycle Assessment (LCA) of the two production chains. The study tracks CO_2 emissions, energy efficiency, water and resources consumption, and environmental impacts (Acidification Potential – AP, Global Warming Potential – GWP, Eutrophication Potential – EP, and Human Toxicity Potential – TP). The boundaries of the biodiesel production chains extend from the extraction of raw-materials to its final use as transportation fuel in buses, applied to the Brazilian scenario. Results show that substitution of the methylic route with the ethylic route does not attribute significant environmental benefits. Furthermore, the ethylic route presents competitive advantages only in the category of GWP, and exhibits inferior performance in the remaining evaluated impact categories. Finally, a greater consumption of water and energy

Methyl biodiesel from Dipteryx lacunifera: preparation, characterization and effect of antioxidant on the oxidation stability

International Nuclear Information System (INIS)

Araujo, Francisca Diana da Silva; Moura, Carla Veronica Rodarte de; Chaves, Mariana H.

2010-01-01

The objective of this work was to study the potentialities of Dipteryx lacunifera Ducke seeds oil for biodiesel production. The yield in oil was of 46.11 ± 0.37%. Methyl biodiesel was prepared by base catalyzed transesterification yielding 88.13% and percentage conversion of triglycerides to corresponding methyl ester of 89.1%. The addition of the tertiary butylhydroquinone (TBHQ, 50 ppm), butylated hydroxytoluene (BHT, 50 ppm) and cashew nut shell liquid (CNSL, 2000 ppm) antioxidants in the biodiesel contributed to the increase of the induction period of 2.97 h for 8.08; 6.06 and 6.02 h, respectively. (author)

Transesterification of rubber seed oil by sonication technique for the production of methyl esters

Energy Technology Data Exchange (ETDEWEB)

Ragavan, S.N.; Roy, D.V. [Scott Christian College (Autonomous), Department of Chemistry, Research Centre, Nagercoil, Tamil Nadu (India)

2011-07-15

The ever-increasing concern due to the fast-depleting energy sources and the environmental impact of the fossil fuel burning has provoked the researchers to turn out for an environmentally benign fuel source. Biodiesel (fatty acid methyl esters) being renewable, biodegradable, non-toxic and eco-friendly, is now gaining momentum. Added carbon sequestration ability of rubber trees has made it one of the best sources for biodiesel in developing countries. Fatty acid methyl esters (FAMEs) from high acid content (23%) rubber seed oil by sonication technique at room temperature (32 C) is of good yield (80%). The FAMEs produced have acceptable fuel standards as specified by ASTM D 6751. This study deals with the utilisation of FAMEs as an alternate fuel for petrodiesel. (orig.)

A study of production and characterization of Manketti (Ricinodendron rautonemii methyl ester and its blends as a potential biodiesel feedstock

Directory of Open Access Journals (Sweden)

A.E. Atabani

2014-12-01

Full Text Available Globally, more than 350 oil-bearing crops are known as potential biodiesel feedstocks. This study reports on production and characterization of Manketti (Ricinodendron rautonemii methyl ester and its blends with diesel. The effect of Manketti biodiesel (B5 on engine and emissions performance was also investigated. The cloud, pour and cold filter plugging points of the produced biodiesel were measured at 1, 3 and 5 °C, respectively. However, the kinematic viscosity of the biodiesel generated was found to be 8.34 mm2/s which was higher than the limit described by ASTM D6751 and EN 14214. This can be attributed to the high kinematic viscosity of the parent oil (132.75 mm2/s. Nevertheless, blending with diesel improved this attribute. Moreover, it is observed that at all engine speeds, B5 produced lower brake power (1.18% and higher brake specific fuel consumption (2.26% compared to B0 (neat diesel. B5 increased the CO and HC emissions by 32.27% and 37.5%, respectively, compared to B0. However, B0 produced 5.26% higher NO emissions than B5.

Performance and emission characteristics of a DI compression ignition engine operated on Honge, Jatropha and sesame oil methyl esters

Energy Technology Data Exchange (ETDEWEB)

Banapurmath, N.R.; Tewari, P.G. [Department of Mechanical Engineering, B.V.B. College of Engineering and Technology, Vidyanagar, Poona-Bangalore Road, Hubli 580031 (India); Hosmath, R.S. [Department of Mechanical Engineering, K.L.E' s C.E.T., Belgaum (India)

2008-09-15

The high viscosity of vegetable oils leads to problem in pumping and spray characteristics. The inefficient mixing of vegetable oils with air contributes to incomplete combustion. The best way to use vegetable oils as fuel in compression ignition (CI) engines is to convert it into biodiesel. Biodiesel is a methyl or ethyl ester of fatty acids made from vegetable oils (both edible and non-edible) and animal fat. The main resources for biodiesel production can be non-edible oils obtained from plant species such as Pongamia pinnata (Honge oil), Jatropha curcas (Ratanjyot), Hevea brasiliensis (Rubber) and Calophyllum inophyllum (Nagchampa). Biodiesel can be used in its pure form or can be blended with diesel to form different blends. It can be used in CI engines with very little or no engine modifications. This is because it has properties similar to mineral diesel. This paper presents the results of investigations carried out on a single-cylinder, four-stroke, direct-injection, CI engine operated with methyl esters of Honge oil, Jatropha oil and sesame oil. Comparative measures of brake thermal efficiency, smoke opacity, HC, CO, NO{sub X}, ignition delay, combustion duration and heat release rates have been presented and discussed. Engine performance in terms of higher brake thermal efficiency and lower emissions (HC, CO, NO{sub X}) with sesame oil methyl ester operation was observed compared to methyl esters of Honge and Jatropha oil operation. (author)

Use of tobacco seed oil methyl ester in a turbocharged indirect injection diesel engine

International Nuclear Information System (INIS)

Usta, N.

2005-01-01

Vegetable oils and their methyl/ethyl esters are alternative renewable fuels for compression ignition engines. Different kinds of vegetable oils and their methyl/ethyl esters have been tested in diesel engines. However, tobacco seed oil and tobacco seed oil methyl ester have not been tested in diesel engines, yet. Tobacco seed oil is a non-edible vegetable oil and a by-product of tobacco leaves production. To the author's best knowledge, this is the first study on tobacco seed oil methyl ester as a fuel in diesel engines. In this study, potential tobacco seed production throughout the world, the oil extraction process from tobacco seed and the transesterification process for biodiesel production were examined. The produced tobacco seed oil methyl ester was characterized by exposing its major properties. The effects of tobacco seed oil methyl ester addition to diesel No. 2 on the performance and emissions of a four cycle, four cylinder turbocharged indirect injection (IDI) diesel engine were examined at both full and partial loads. Experimental results showed that tobacco seed oil methyl ester can be partially substituted for the diesel fuel at most operating conditions in terms of performance parameters and emissions without any engine modification and preheating of the blends. (Author)

Production of FAME biodiesel in E. coli by direct methylation with an insect enzyme.

Science.gov (United States)

Sherkhanov, Saken; Korman, Tyler P; Clarke, Steven G; Bowie, James U

2016-04-07

Most biodiesel currently in use consists of fatty acid methyl esters (FAMEs) produced by transesterification of plant oils with methanol. To reduce competition with food supplies, it would be desirable to directly produce biodiesel in microorganisms. To date, the most effective pathway for the production of biodiesel in bacteria yields fatty acid ethyl esters (FAEEs) at up to ~1.5 g/L. A much simpler route to biodiesel produces FAMEs by direct S-adenosyl-L-methionine (SAM) dependent methylation of free fatty acids, but FAME production by this route has been limited to only ~16 mg/L. Here we employ an alternative, broad spectrum methyltransferase, Drosophila melanogaster Juvenile Hormone Acid O-Methyltransferase (DmJHAMT). By introducing DmJHAMT in E. coli engineered to produce medium chain fatty acids and overproduce SAM, we obtain medium chain FAMEs at titers of 0.56 g/L, a 35-fold increase over titers previously achieved. Although considerable improvements will be needed for viable bacterial production of FAMEs and FAEEs for biofuels, it may be easier to optimize and transport the FAME production pathway to other microorganisms because it involves fewer enzymes.

Isolation and screening of heterocystous cyanobacterial strains for biodiesel production by evaluating the fuel properties from fatty acid methyl ester (FAME) profiles.

Science.gov (United States)

Anahas, Antonyraj Matharasi Perianaika; Muralitharan, Gangatharan

2015-05-01

This study reports on the biodiesel quality parameters of eleven heterocystous cyanobacterial strains based on fatty acid methyl esters (FAME) profiles. The biomass productivity of the tested cyanobacterial strains ranged from 9.33 to 20.67 mg L(-1) d(-1) while the lipid productivity varied between 0.65 and 2.358 mg L(-1) d(-1). The highest biomass and lipid productivity was observed for Calothrix sp. MBDU 013 but its lipid content is only 11.221 in terms of percent dry weight, next to the Anabaena sphaerica MBDU 105, whose lipid content is high. To identify the most competent isolate, a multi-criteria decision analyses (MCDA) was performed by including the key chemical and physical parameters of biodiesel calculated from FAME profiles. The isolate A.sphaerica MBDU 105 is the most promising biodiesel feed stock based on decision vector through Preference Ranking Organisation Method for Enrichment Evaluation (PROMETHEE) and Graphical Analysis for Interactive Assistance (GAIA) analysis. Copyright © 2014 Elsevier Ltd. All rights reserved.

Biodiesel production from vegetable oil and waste animal fats in a pilot plant.

Science.gov (United States)

Alptekin, Ertan; Canakci, Mustafa; Sanli, Huseyin

2014-11-01

In this study, corn oil as vegetable oil, chicken fat and fleshing oil as animal fats were used to produce methyl ester in a biodiesel pilot plant. The FFA level of the corn oil was below 1% while those of animal fats were too high to produce biodiesel via base catalyst. Therefore, it was needed to perform pretreatment reaction for the animal fats. For this aim, sulfuric acid was used as catalyst and methanol was used as alcohol in the pretreatment reactions. After reducing the FFA level of the animal fats to less than 1%, the transesterification reaction was completed with alkaline catalyst. Due to low FFA content of corn oil, it was directly subjected to transesterification. Potassium hydroxide was used as catalyst and methanol was used as alcohol for transesterification reactions. The fuel properties of methyl esters produced in the biodiesel pilot plant were characterized and compared to EN 14214 and ASTM D6751 biodiesel standards. According to the results, ester yield values of animal fat methyl esters were slightly lower than that of the corn oil methyl ester (COME). The production cost of COME was higher than those of animal fat methyl esters due to being high cost biodiesel feedstock. The fuel properties of produced methyl esters were close to each other. Especially, the sulfur content and cold flow properties of the COME were lower than those of animal fat methyl esters. The measured fuel properties of all produced methyl esters met ASTM D6751 (S500) biodiesel fuel standards. Copyright © 2014 Elsevier Ltd. All rights reserved.

Biodiesel fuels

Science.gov (United States)

The mono-alkyl esters, most commonly the methyl esters, of vegetable oils, animal fats or other materials consisting mainly of triacylglycerols, often referred to as biodiesel, are an alternative to conventional petrodiesel for use in compression-ignition engines. The fatty acid esters that thus com...

Production of methyl ester from oil in the wastewater pond of a palm oil factory

Directory of Open Access Journals (Sweden)

Tongurai, C.

2007-11-01

Full Text Available This research studied the suitable technique for the production of methyl ester from waste palm oil in the water pond of a palm oil mill. The composition of the waste palm oil was 73.82% fatty acid, 5.07% triglyceride, 3.39% diglyceride and 17.76% unknown compounds. The unknown compounds were separated via simple distillation carried out at a temperature range of 300-350oC.First, the experiments were carried out in screw capped bottles using filtrated as-received waste oil as the reactant. The esterification and transesterification process were conducted using sulfuric acid catalyst in a methanol solution. The key parameters studied were mole ratio of waste oil to methanol (1:1 to 1:72, amount of catalyst from 0.1-20 v/w% of the reactant, temperature range of 60-98oC and reaction time range of 15-180 minutes. Thin Layer Chromatography (TLC analysis showed 85-90% purity of methyl ester with 4-5% of mono-, di-, and triglycerides and fatty acids and about 5-10% of the unknown compounds for the best condition. The resulting yield of biodiesel was 84-88%. Eradication of contaminants by distillation gave about a 75% distillate yield. Distilled waste palm oil was esterified and transesterified using the previous optimum condition of as-received waste oil, but the reaction time and temperature were varied. The optimal result was obtained by using distilled waste palm oil to methanol molar ratio of 1:8, sulfuric acid of 1 v/w% of reactant, reaction temperature of 70oC and reaction time of 1 hour. TLC analysis indicated a biodiesel composition of methyl ester, free fatty acid, diglyceride and monoglyceride of 96.39%, 3.20%, 0.24% and 0.17%, respectively. The yield of biodiesel was 96-98% having physical fuel properties according to Thailand standard for methyl esterFinally, the distilled waste palm oil was esterified using a 3 liters continuous stirred-tank reactor (CSTR. Using the suitable condition for the batch process and an hour retention time, the

Correlation for the estimation of the density of fatty acid esters fuels and its implications. A proposed Biodiesel Cetane Index.

Science.gov (United States)

Lapuerta, Magín; Rodríguez-Fernández, José; Armas, Octavio

2010-09-01

Biodiesel fuels (methyl or ethyl esters derived from vegetables oils and animal fats) are currently being used as a means to diminish the crude oil dependency and to limit the greenhouse gas emissions of the transportation sector. However, their physical properties are different from traditional fossil fuels, this making uncertain their effect on new, electronically controlled vehicles. Density is one of those properties, and its implications go even further. First, because governments are expected to boost the use of high-biodiesel content blends, but biodiesel fuels are denser than fossil ones. In consequence, their blending proportion is indirectly restricted in order not to exceed the maximum density limit established in fuel quality standards. Second, because an accurate knowledge of biodiesel density permits the estimation of other properties such as the Cetane Number, whose direct measurement is complex and presents low repeatability and low reproducibility. In this study we compile densities of methyl and ethyl esters published in literature, and proposed equations to convert them to 15 degrees C and to predict the biodiesel density based on its chain length and unsaturation degree. Both expressions were validated for a wide range of commercial biodiesel fuels. Using the latter, we define a term called Biodiesel Cetane Index, which predicts with high accuracy the Biodiesel Cetane Number. Finally, simple calculations prove that the introduction of high-biodiesel content blends in the fuel market would force the refineries to reduce the density of their fossil fuels. Copyright 2010 Elsevier Ireland Ltd. All rights reserved.

Sintesis Metil Ester dari Minyak Biji Kemiri (Aleurites Molluccana Menggunakan Metode Ultrasonokimia

Directory of Open Access Journals (Sweden)

Rahmawati Aziz

2016-01-01

Full Text Available Using the fuel oil is the basic necessary in the world now. But, the raw material cannot be updated.  To ensure the availability of the fuel oil so, the newest of alternative energy is explored it. One of the ways is biodiesel which made from vegetable oil. In this research is resulted from the transesterification reaction between candlenut oil and methanol by utilizing ultrasonic equipment. This research has passed some phases, they are the determining of acid number in oil then continued by creating biodiesel from ultrasonic wave 47 kHz. Identification of FTIR and GCMS are two methods which used to analyze the component compound in biodiesel product. The conversion number that be gotten from FAME with reaction of variation time 30, 40 and 50 in succession 0,037%, 0,029% and 0,018%. The result analysis of FTIR shows some of functional groups which are special from biodiesel. While the result of GCMS analysis is known that there are 5 component compounds in biodiesel namely ester methyl palmitic acid, ester methyl olead, stearata ester methyl, linoleic ester methyl and elaidic ester methyl.

Effects of partial hydrogenation, epoxidation, and hydroxylation on the fuel properties of fatty acid methyl esters

Energy Technology Data Exchange (ETDEWEB)

Wadumesthrige, Kapila; Salley, Steven O.; Ng, K.Y. Simon [Department of Chemical Engineering and Materials Science, Wayne State University, 5050 Anthony Wayne Drive, Detroit, MI 48202 (United States)

2009-10-15

The properties of biodiesel depend on the chemical structure of individual fatty acid methyl esters (FAME). In this work the chemical structure of fatty acid chains was modified by catalytic hydrogenation, epoxidation and hydroxylation under controlled conditions. Hydrolysis of ester functionality or oxidation of fatty acid chain was not observed during these reactions. The properties of hydrogenated FAME strongly depend on the hydrogenation time. The total saturated fatty acid (SFA) percentage increased from 29.3% to 76.2% after 2 h of hydrogenation. This hydrogenated FAME showed higher oxidation stability and higher cetane number but poor cold flow properties. Formation of trans FAME was observed during hydrogenation. Both hydroxylation and epoxidation resulted in a decrease of unsaturated fatty acid methyl ester (UFA) fraction. The percentages of total unsaturated FAME decreased 39% in the epoxidation reaction and 44% in the hydroxylation reaction. The addition of hydroxyl groups to the unsaturated regions of the fatty acid chain yields biodiesel with better cold flow properties, increased lubricity and slightly increased oxidative stability. However, epoxy FAME shows some interesting properties such as higher oxidation stability, higher cetane number and acceptable cold flow properties, which met the limits of ASTM D6751 biodiesel specifications. (author)

Reaction product of pyrogallol with methyl linoleate and its antioxidant potential for biodiesel

Science.gov (United States)

Sutanto, H.; Ainny, L.; Lukman; Susanto, B. H.; Nasikin, M.

2018-03-01

The demand of biodiesel as an alternative fuel is increasing due to fossil fuel depletion. Biodiesel is a renewable diesel fuel in the form of fatty acid methyl ester or FAME as a result of an esterification of plant oils in a presence of catalyst. Compared to the conventional diesel fuel, biodiesel is more biodegradable, has higher lubricity, and lower toxic emissions. However, the high content of unsaturated fatty acid leads to a problem that biodiesel is prone to oxidation during storage period. This oxidation instability causes degradation of fuel quality and will affect engine performance. Pyrogallol and other phenolic derivatives have been used as the antioxidant additives to prevent biodiesel oxidation. As reported in many researches, pyrogallol is one of the best phenolic antioxidant. However, its low solubility in biodiesel needs an attention. Several reports indicate the increasing solubility of pyrogallol using molecule modification with the addition of alkyl groups to its benzene ring via electrophilic substitution. This paper discusses the idea about modification of pyrogallol molecule and methyl linoleate using 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical in order to increase its solubility in biodiesel while keeping its antioxidant property. Three responses were analyzed to examine the antioxidant activity: iodine value, viscosity, and color intensity. The result shown that the addition of 0.1% reaction product exhibit antioxidant activity in biodiesel.

Pembuatan Biodiesel dari Minyak Kelapa Menggunakan Microwave : Penggunaan Katalis KOH dengan Konsentrasi Rendah

Directory of Open Access Journals (Sweden)

Gus Ali Nur Rohman

2017-01-01

Full Text Available Penelitian pembuatan methyl ester (biodiesel dari minyak kelapa dengan katalis KOH dengan bantuan gelombang mikro (microwave di latar belakangi oleh adanya krisis energi sehingga memerlukan metode baru untuk membuat renewable energy dalam hal ini adalah biodiesel. Tujuan dari penelitian ini adalah mempelajari proses pembuatan biodiesel dengan metode radiasi microwave, pengaruh konsentrasi katalis KOH, pengaruh daya, waktu pemanasan yang digunakan terhadap yield dan viskositas biodiesel yang dihasilkan. Pembuatan methyl ester (biodiesel dari minyak kelapa dilakukan dengan perbandingan mol minyak : metanol = 1 : 9. Biodiesel yang dihasilkan kemudian dianalisa dengan uji viskositas, uji flash point, dan uji gas chromatography (GC. Yield optimum pada pembuatan methyl ester dari minyak kelapa dengan metode microwave-assisted transesterification untuk katalis KOH adalah konsentrasi 0,5% dengan daya 400 watt dan waktu reaksi 4 menit.

Performance, Emissions and Combustion Characteristics of a Single Cylinder Diesel Engine Fuelled with Blends of Jatropha Methyl Ester and Diesel

Directory of Open Access Journals (Sweden)

Debasish Padhee

2014-05-01

Full Text Available In order to meet the energy requirements, there has been growing interest in alternative fuels like biodiesels, ethyl alcohol, biogas, hydrogen and producer gas to provide a suitable diesel substitute for internal combustion engines. An experimental investigation was performed to study the performance, emissions and combustion characteristics of diesel engine fuelled with blends of Jatropha methyl ester and diesel. In the present work three different fuel blends of Jatropha methyl ester (B10, B20, B40 and B100 were used. The increments in load on the engine increase the brake thermal efficiency, exhaust gas temperature and lowered the brake specific fuel consumption. The biodiesel blends produce lower carbon monoxide & unburned hydrocarbon emission and higher carbon dioxide & oxides of nitrogen than neat diesel fuel. From the results it was observed that the ignition delays decreased with increase in concentration of biodiesel in biodiesel blends with diesel. The combustion characteristics of single-fuel for biodiesel and diesel have similar combustion pressure and HRR patterns at different engine loads but it was observed that the peak cylinder pressure and heat release rate were lower for biodiesel blends compared to those of diesel fuel combustion.

Effect of reaction temperature on biodiesel production from waste cooking oil using lipase as biocatalyst

Science.gov (United States)

Istiningrum, Reni Banowati; Aprianto, Toni; Pamungkas, Febria Lutfi Udin

2017-12-01

This study aims to determine the effect of temperature on conversion of biodiesel from waste cooking oil enzymatically using lipase extracted from rice bran. The feedstock was simulated waste cooking oil and lipase enzyme was extracted with buffer pH variation. The enzyme activity was titrimetrically determined and the optimum pH buffer was used to study the effect of temperature on the transesterification reaction. Temperature effects were assessed in the range of 45-60 °C and the content of methyl esters in biodiesel was determined by GC-MS. The reaction temperature significantly influences the transesterification reaction with optimum biodiesel conversion occurred at 55 °C with methyl ester content of 81.19%. The methyl ester composition in the resulting biodiesel is methyl palmitate, methyl oleate and methyl stearate.

Certain investigation in a compression ignition engine using rice bran methyl ester fuel blends with ethanol additive

Directory of Open Access Journals (Sweden)

Krishnan Arumugam

2017-01-01

Full Text Available In this study and analysis, the physical properties such as calorific value, viscosity, flash, and fire point temperatures of rice bran oil methyl ester were found. The rice bran oil biodiesel has been prepared by transesterification process from pure rice bran oil in the presence of methanol and NaOH. Moreover, property enhancement of rice bran oil methyl ester was also made by adding different additives such as ethanol in various proportions. Rice bran oil methyl ester with 1, 3, and 5% ethanol were analyzed for its fuel properties. The effects of diesel-B20ROME blends with ethanol additive of 1, 3, and 5% on a compression ignition engine were examined considering its emissions. It is found that the increase in biodiesel concentration in the fuel blend influences CO2 and NOx emissions. On the other hand CO and HC emissions are reduced. It is interesting to observe the emission as ethanol-B20ROME blends, reduces CO2 and NOx which are the major contributors to global warming. As the NOx and CO2 can be reduced drastically by the proposed blends, the global warming can be reduced considerably.

Computational optimization of biodiesel combustion using response surface methodology

Directory of Open Access Journals (Sweden)

Ganji Prabhakara Rao

2017-01-01

Full Text Available The present work focuses on optimization of biodiesel combustion phenomena through parametric approach using response surface methodology. Physical properties of biodiesel play a vital role for accurate simulations of the fuel spray, atomization, combustion, and emission formation processes. Typically methyl based biodiesel consists of five main types of esters: methyl palmitate, methyl oleate, methyl stearate, methyl linoleate, and methyl linolenate in its composition. Based on the amount of methyl esters present the properties of pongamia bio-diesel and its blends were estimated. CONVERGETM computational fluid dynamics software was used to simulate the fuel spray, turbulence and combustion phenomena. The simulation responses such as indicated specific fuel consumption, NOx, and soot were analyzed using design of experiments. Regression equations were developed for each of these responses. The optimum parameters were found out to be compression ratio – 16.75, start of injection – 21.9° before top dead center, and exhaust gas re-circulation – 10.94%. Results have been compared with baseline case.

Test results of pongamia pinnata methyl esters with direct injection diesel engine

International Nuclear Information System (INIS)

Bannikov, MG.; Chattha, J.A.; Khan, A.F.

2011-01-01

Pongamia Pinnata oil is considered as a potential source of biodiesel production in Pakistan. When selecting source for commercial production of biodiesel several criteria are used. One of them is that biodiesel or biodiesel/diesel fuel blends must provide satisfactory performance and emissions of the diesel engine without or with a little engine modification. In this research performance and emissions characteristics of a direct injection diesel engine running on Pongamia Pinnata methyl esters were discussed. Discussion was supported by an analysis of combustion characteristics derived from in-cylinder pressure data. Engine running on a neat biodiesel showed higher brake specific fuel consumption and lower brake fuel conversion efficiency at all loads, whereas emissions were improved except of carbon monoxide emission at high loads. Decrease in brake efficiency and reduction of nitrogen oxides emissions were attributed solely to the change in the rate of heat release. Deposits on fuel infector nozzle were observed when engine was running on the neat biodiesel. Based on test results conclusion was made that Pongamia biodiesel/diesel fuel blends can effectively be used as a diesel oil substitute. (author)

Technical aspects of biodiesel production from vegetable oils

Directory of Open Access Journals (Sweden)

Krishnakumar Janahiraman

2008-01-01

Full Text Available Biodiesel, a promising substitute as an alternative fuel has gained significant attention due to the finite nature of fossil energy sources and does not produce sulfur oxides and minimize the soot particulate in comparison with the existing one from petroleum diesel. The utilization of liquid fuels such as biodiesel produced from vegetable oil by transesterification process represents one of the most promising options for the use of conventional fossil fuels. In the first step of this experimental research, edible rice bran oil used as test material and converted into methyl ester and non-edible jatropha vegetable oil is converted into jatropha oil methyl ester, which are known as biodiesel and they are prepared in the presence of homogeneous acid catalyst and optimized their operating parameters like reaction temperature, quantity of alcohol and the catalyst requirement, stirring rate and time of esterification. In the second step, the physical properties such as density, flash point, kinematic viscosity, cloud point, and pour point were found out for the above vegetable oils and their methyl esters. The same characteristics study was also carried out for the diesel fuel for obtaining the baseline data for analysis. The values obtained from the rice bran oil methyl ester and jatropha oil methyl ester are closely matched with the values of conventional diesel and it can be used in the existing diesel engine without any hardware modification. In the third step the storage characteristics of biodiesel are also studied. .

Investigation of palm methyl-ester bio-diesel with additive on performance and emission characteristics of a diesel engine under 8-mode testing cycle

Directory of Open Access Journals (Sweden)

S. Senthilkumar

2015-09-01

Full Text Available Biodiesel is receiving increasing attention each passing day because of its same diesel-like fuel properties and compatibility with petroleum-based diesel fueled engines. Therefore, in this paper the prospects and opportunities of using various blends of methyl esters of palm oil as fuel in an engine with and without the effect of multi-functional fuel additive (MFA, Multi DM 32 are studied to arrive at an optimum blend of bio-diesel best suited for low emissions and minimal power drop. Experimental tests were conducted on a four stroke, three cylinder and naturally aspirated D.I. Diesel engine with diesel and various blend percentages of 20%, 40%, 45%, and 50% under the 8 mode testing cycle. The effect of fuel additive was tested out on the optimum blend ratio of the bio-diesel so as to achieve further reduced emissions. Comparison of results shows that, 73% reduction in hydrocarbon emission, 46% reduction in carbon monoxide emission, and around 1% reduction in carbon dioxide emission characteristics. So it is observed that the blend ratio of 40% bio-diesel with MFA fuel additive creates reduced emission and minimal power drop due to effective combustion even when the calorific value is comparatively lower due to its higher cetane number.

Experimental and chemical kinetic modeling study of small methyl esters oxidation: Methyl (E)-2-butenoate and methyl butanoate

Energy Technology Data Exchange (ETDEWEB)

Gail, S.; Sarathy, S.M.; Thomson, M.J. [Department of Mechanical and Industrial Engineering, University of Toronto, Toronto, ON M5S 3G8 (Canada); Dievart, P.; Dagaut, P. [CNRS, 1C, Ave de la Recherche Scientifique, 45071 Orleans Cedex 2 (France)

2008-12-15

This study examines the effect of unsaturation on the combustion of fatty acid methyl esters (FAME). New experimental results were obtained for the oxidation of methyl (E)-2-butenoate (MC, unsaturated C{sub 4} FAME) and methyl butanoate (MB, saturated C{sub 4} FAME) in a jet-stirred reactor (JSR) at atmospheric pressure under dilute conditions over the temperature range 850-1400 K, and two equivalence ratios ({phi}=0.375,0.75) with a residence time of 0.07 s. The results consist of concentration profiles of the reactants, stable intermediates, and final products, measured by probe sampling followed by on-line and off-line gas chromatography analyses. The oxidation of MC and MB in the JSR and under counterflow diffusion flame conditions was modeled using a new detailed chemical kinetic reaction mechanism (301 species and 1516 reactions) derived from previous schemes proposed in the literature. The laminar counterflow flame and JSR (for {phi}=1.13) experimental results used were from a previous study on the comparison of the combustion of both compounds. Sensitivity analyses and reaction path analyses, based on rates of reaction, were used to interpret the results. The data and the model show that MC has reaction pathways analogous to that of MB under the present conditions. The model of MC oxidation provides a better understanding of the effect of the ester function on combustion, and the effect of unsaturation on the combustion of fatty acid methyl ester compounds typically found in biodiesel. (author)

Property modification of jatropha oil biodiesel by blending with other biodiesels or adding antioxidants

International Nuclear Information System (INIS)

Chen, Yi-Hung; Chen, Jhih-Hong; Luo, Yu-Min; Shang, Neng-Chou; Chang, Cheng-Hsin; Chang, Ching-Yuan; Chiang, Pen-Chi; Shie, Je-Lueng

2011-01-01

The feasibility of biodiesel production from jatropha (Jatropha curcas) oil was investigated with respect to the biodiesel blending properties and its oxidation stability with antioxidants. The JME (jatropha oil methyl esters) had the cetane number of 54, cold filter plugging point of -2 o C, density of 881 kg/m 3 at 15 o C, ester content of 99.4 wt.%, iodine value of 96.55 g I 2 /100 g, kinematic viscosity of 4.33 mm 2 /s at 40 o C, and oxidation stability of 3.86 h. Furthermore, the JME was blended with palm oil biodiesel and soybean oil biodiesel at various weight ratios and evaluated for fuel properties as compared to the relevant specifications. In addition, several antioxidants at concentrations between 100 and 1000 ppm were studied for their potential to improve the oxidation stability of the JME. The relationship between the IP (induction period) in the measurement of the oxidation stability associated with the antioxidant consumption in the JME was described by first-order reaction rate kinetics. Moreover, the ln IP (natural logarithm of the IP) at various concentrations of pyrogallol showed a linear relationship with the test temperature. The oxidation stability at ambient temperatures was predicted on the basis of an extrapolation of the temperature-dependent relationship. -- Highlights: → Jatropha oil methyl esters had satisfactory biodiesel properties except for the oxidation stability. → The oxidation stability and cold filter plugging point of the jatropha-based biodiesel blends cannot meet the EN 14214 requirements simultaneously. → The addition of pyrogallol was recommended for the stabilization of the jatropha oil methyl esters with a concentration of 100-250 ppm.

Lipase immobilization and production of fatty acid methyl esters from canola oil using immobilized lipase

International Nuclear Information System (INIS)

Yuecel, Yasin; Demir, Cevdet; Dizge, Nadir; Keskinler, Buelent

2011-01-01

Lipase enzyme from Aspergillus oryzae (EC 3.1.1.3) was immobilized onto a micro porous polymeric matrix which contains aldehyde functional groups and methyl esters of long chain fatty acids (biodiesel) were synthesized by transesterification of crude canola oil using immobilized lipase. Micro porous polymeric matrix was synthesized from styrene-divinylbenzene (STY-DVB) copolymers by using high internal phase emulsion technique and two different lipases, Lipozyme TL-100L ® and Novozym 388 ® , were used for immobilization by both physical adsorption and covalent attachment. Biodiesel production was carried out with semi-continuous operation. Methanol was added into the reactor by three successive additions of 1:4 M equivalent of methanol to avoid enzyme inhibition. The transesterification reaction conditions were as follows: oil/alcohol molar ratio 1:4; temperature 40 o C and total reaction time 6 h. Lipozyme TL-100L ® lipase provided the highest yield of fatty acid methyl esters as 92%. Operational stability was determined with immobilized lipase and it indicated that a small enzyme deactivation occurred after used repeatedly for 10 consecutive batches with each of 24 h. Since the process is yet effective and enzyme does not leak out from the polymer, the method can be proposed for industrial applications. -- Research highlights: → Lipozyme TL-100L and Novozym 388 were immobilized onto micro porous polymeric matrix by both physical adsorption and covalent linking. → Immobilized enzymes were used for synthesis of fatty acid methyl esters by transesterification of canola oil and methanol using semi-continuous operation system. → According to chromatographic analysis, Lipase Lipozyme TL-100L resulted in the highest yield of methyl ester as 92%.

Performance and emission of generator Diesel engine using methyl esters of palm oil and diesel blends at different compression ratio

Science.gov (United States)

Aldhaidhawi, M.; Chiriac, R.; Bădescu, V.; Pop, H.; Apostol, V.; Dobrovicescu, A.; Prisecaru, M.; Alfaryjat, A. A.; Ghilvacs, M.; Alexandru, A.

2016-08-01

This study proposes engine model to predicate the performance and exhaust gas emissions of a single cylinder four stroke direct injection engine which was fuelled with diesel and palm oil methyl ester of B7 (blends 7% palm oil methyl ester with 93% diesel by volume) and B10. The experiment was conducted at constant engine speed of 3000 rpm and different engine loads operations with compression ratios of 18:1, 20:1 and 22:1. The influence of the compression ratio and fuel typeson specific fuel consumption and brake thermal efficiency has been investigated and presented. The optimum compression ratio which yields better performance has been identified. The result from the present work confirms that biodiesel resulting from palm oil methyl ester could represent a superior alternative to diesel fuel when the engine operates with variable compression ratios. The blends, when used as fuel, result in a reduction of the brake specific fuel consumption and brake thermal efficiency, while NOx emissions was increased when the engine is operated with biodiesel blends.

BIODIESEL DARI CAMPURAN LEMAK SAPI (Beef Tallow DAN MINYAK SAWIT

Directory of Open Access Journals (Sweden)

Wara Dyah Pita Rengga

2013-05-01

catalyst. The transesterification process was carried for 90 minutes at ±65°C. Transesterification process produces methyl ester and glycerol. The produced methyl ester on the upper layer was separated from the glycerol and then washed. The produced methyl ester was tested to determine the acid number, viscosity, and density. Analysis of the methyl ester components using GC-MS was also conducted. The experimental results show the yield of produced biodiesel from mixed-oil of beef tallow and palm oil (3:1 was 75.93%. The tested acid number, density, and viscosity were 0.67124 mg-KOH/g, 85.76 kg/cm³, and 3.0074 mm2/s, respectively. Data of the tested methyl ester properties are in accordance with the quality of standard ISO for methyl ester. The content of the produced methyl ester from the mixed-oil of beef tallow and palm oil are metiloleat and methyl palmitate.

Biodiesel as an Alternative Fuel for Diesel Engines

OpenAIRE

F. Halek; A. Kavousi; M. Banifatemi

2009-01-01

There is growing interest in biodiesel (fatty acid methyl ester or FAME) because of the similarity in its properties when compared to those of diesel fuels. Diesel engines operated on biodiesel have lower emissions of carbon monoxide, unburned hydrocarbons, particulate matter, and air toxics than when operated on petroleum-based diesel fuel. Production of fatty acid methyl ester (FAME) from rapeseed (nonedible oil) fatty acid distillate having high free fatty acids (FFA) ...

Production and comparative fuel properties of biodiesel from non-edible oils: Jatropha curcas, Sterculia foetida and Ceiba pentandra

International Nuclear Information System (INIS)

Ong, H.C.; Silitonga, A.S.; Masjuki, H.H.; Mahlia, T.M.I.; Chong, W.T.; Boosroh, M.H.

2013-01-01

Highlights: • Biodiesel is an effective way to overcome environmental issue by diesel fuel. • Two stage acid (H 2 SO 4 ) and base (NaOH) catalyst transesterification process ware carried out to produce methyl ester. • Properties of produced jatropha, sterculia and ceiba methyl ester are within the ASTM D6751 standard. • The methyl ester content was 96.75%, 97.50% and 97.72% for JCME, SFME and CPME respectively. - Abstract: Biodiesel production from non-edible vegetable oil is one of the effective ways to overcome the problems associated with energy crisis and environmental issues. The non-edible oils represent potential sources for future energy supply. In this study, the physical and chemical properties of crude Jatropha curcas oil (CJCO), crude Sterculia foetida oil (CSFO) and crude Ceiba pentandra oil (CCPO) and its methyl ester have been studied. The acid values of three oils were found to be 12.78 mg KOH per g, 5.11 mg KOH per g and 11.99 mg KOH per g which required acid-esterification and alkali-transesterification process. Acid value was decreased by esterification process using sulfuric acid anhydrous (H 2 SO 4 ) as a catalyst and alkaline (NaOH) catalyst transesterification was carried out for the conversion of crude oil to methyl esters. The optimal conditions of FAME yield achieved for those three biodiesel were 96.75%, 97.50% and 97.72% respectively. Furthermore, the fuel properties of J. curcas methyl ester (JCME), S. foetida methyl ester (SFME) and C. pentandra methyl ester (CPME) were determined and evaluated. As a result, those produced biodiesel matched and fulfilled ASTM 6751 and EN 14214 biodiesel standards. Based on the results, JCME, SFME and CPME are potential non-edible feedstock for biodiesel production

USAGE OF METHYL ESTER PRODUCED FROM WASTE GRAPE AND MN ADDITIVE AS ALTERNATIVE DIESEL FUEL

Directory of Open Access Journals (Sweden)

Hanbey Hazar

2017-06-01

Full Text Available In this study, methyl ester was produced from waste grape pulp sources. The produced methyl ester was mixed with diesel in different proportions, and was tested for engine performance and emission. It was found that with increasing biodiesel content, the specific fuel consumption and exhaust temperature have increased partially, while the CO, HC and smoke emissions decreased significantly. Additionally, in the scope of this study, dodecanol, propylene glycol and Mn based additives were added to fuel B50 to improve the emission and engine performance values. With the presence of additives, an increase in the exhaust temperature was observed, while a decrease in the specific fuel consumption, CO, HC, and smoke emissions were detected.

A Simple, Safe Method for Preparation of Biodiesel

Science.gov (United States)

Behnia, Mahin S.; Emerson, David W.; Steinberg, Spencer M.; Alwis, Rasika M.; Duenas, Josue A.; Serafino, Jessica O.

2011-01-01

An experiment suitable for organic chemistry students is described. Biodiesel, a "green" fuel, consists of methyl or ethyl esters of long-chain fatty acids called FAMES (fatty acid methyl esters) or FAEES (fatty acid ethyl esters). A quick way to make FAMES is a base-catalyzed transesterification of oils or fats derived from plants or from animal…

Biodiesel production using fatty acids from food industry waste using corona discharge plasma technology.

Science.gov (United States)

Cubas, A L V; Machado, M M; Pinto, C R S C; Moecke, E H S; Dutra, A R A

2016-01-01

This article aims to describe an alternative and innovative methodology to transform waste, frying oil in a potential energy source, the biodiesel. The biodiesel was produced from fatty acids, using a waste product of the food industry as the raw material. The methodology to be described is the corona discharge plasma technology, which offers advantages such as acceleration of the esterification reaction, easy separation of the biodiesel and the elimination of waste generation. The best conditions were found to be an oil/methanol molar ratio of 6:1, ambient temperature (25 °C) and reaction time of 110 min and 30 mL of sample. The acid value indicates the content of free fatty acids in the biodiesel and the value obtained in this study was 0.43 mg KOH/g. Peaks corresponding to octadecadienoic acid methyl ester, octadecanoic acid methyl ester and octadecenoic acid methyl ester, from the biodiesel composition, were identified using GC-MS. A major advantage of this process is that the methyl ester can be obtained in the absence of chemical catalysts and without the formation of the co-product (glycerin). Copyright © 2015 Elsevier Ltd. All rights reserved.

Improving the Cold Temperature Properties of Tallow-Based Methyl Ester Mixtures Using Fractionation, Blending, and Additives

Science.gov (United States)

Elwell, Caleb

Beef tallow is a less common feedstock source for biodiesel than soy or canola oil, but it can have economic benefits in comparison to these traditional feedstocks. However, tallow methyl ester (TME) has the major disadvantage of poor cold temperature properties. Cloud point (CP) is an standard industry metric for evaluating the cold temperature performance of biodiesel and is directly related to the thermodynamic properties of the fuel's constituents. TME has a CP of 14.5°C compared with 2.3°C for soy methyl ester (SME) and -8.3°C for canola methyl ester (CME). In this study, three methods were evaluated to reduce the CP of TME: fractionation, blending with SME and CME, and using polymer additives. TME fractionation (i.e. removal of specific methyl ester constituents) was simulated by creating FAME mixtures to match the FAME profiles of fractionated TME. The fractionation yield was found to be highest at the eutectic point of methyl palmitate (MP) and methyl stearate (MS), which was empirically determined to be at a MP/(MP+MS) ratio of approximately 82%. Since unmodified TME has a MP/(MP+MS) ratio of 59%, initially only MS should be removed to produce a ratio closer to the eutectic point to reduce CP and maximize yield. Graphs relating yield (with 4:1 methyl stearate to methyl oleate carryover) to CP were produced to determine the economic viability of this approach. To evaluate the effect of blending TME with other methyl esters, SME and CME were blended with TME at blend ratios of 0 to 100%. Both the SME/TME and CME/TME blends exhibited decreased CPs with increasing levels of SME and CME. Although the CP of the SME/TME blends varied linearly with SME content, the CP of the CME/TME blends varied quadratically with CME content. To evaluate the potential of fuel additives to reduce the CP of TME, 11 different polymer additives were tested. Although all of these additives were specifically marketed to enhance the cold temperature properties of petroleum diesel or

Chromatographic analyses of fatty acid methyl esters by HPLC-UV and GC-FID

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Myller S.; Pinho, David M.M.; Suarez, Paulo A.Z., E-mail: psuarez@unb.br [Laboratorio de Materiais e Combustiveis, Instituto de Quimica, Universidade de Brasilia, DF (Brazil); Mendonca, Marcio A. [Faculdade de Agronomia e Medicina Veterinaria, Universidade de Brasilia, DF (Brazil); Resck, Ines S. [Laboratorio de Ressonancia Magnetica Nuclear, Universidade de Brasilia, DF (Brazil)

2012-04-15

An analytical method using high performance liquid chromatography with UV detection (HPLC-UV) (method A) was used for simultaneous determination of total amounts of triacylglycerides, diacylglycerides, monoacylglycerides and fatty acid methyl esters in alcoholysis of different oil (cotton, canola, sunflower, corn and soybean) samples. Analyses were carried out at 40 deg C for 20 min using a gradient of methanol (MeOH) and 2-propanol-hexane 5:4 (v/v) (PrHex): 100% of MeOH in 0 min, 50% of MeOH and 50% of PrHex in 10 min maintained with isocratic elution for 10 min. Another HPLC-UV method (method B) with acetonitrile isocratic elution for 34 min was used to determine the fatty acid composition of oils analyzing their methyl ester derivatives. Contents were determined with satisfactory repeatability (relative standard deviation, RSD < 3%), linearity (r{sup 2} > 0.99) and sensitivity (limit of quantification). Method B was compared with an official gas chromatographic method with flame ionization detection (GC-FID) from American Oil Chemists' Society (AOCS) in the determination of fatty acid methyl esters (FAME) in biodiesel real samples. (author)

Experimental investigation of a diesel engine with methyl ester of mango seed oil and diesel blends

Directory of Open Access Journals (Sweden)

K. Vijayaraj

2016-03-01

Full Text Available Petroleum based fuels worldwide have not only resulted in the rapid depletion of conventional energy sources, but have also caused severe air pollution. The search for an alternate fuel has led to many findings due to which a wide variety of alternative fuels are available at our disposal now. The existing studies have revealed the use of vegetable oils for engines as an alternative for diesel fuel. However, there is a limitation in using straight vegetable oils in diesel engines due to their high viscosity and low volatility. In the present work, neat mango seed oil is converted into their respective methyl ester through transesterification process. Experiments are conducted using various blends of methyl ester of mango seed oil with diesel in a single cylinder, four stroke vertical and air cooled Kirloskar diesel engine. The experimental results of this study showed that the MEMSO biodiesel has similar characteristics to those of diesel. The brake thermal efficiency, unburned hydrocarbon and smoke density are observed to be lower in case of MEMSO biodiesel blends than diesel. The CO emission for B25, B50 and B75 is observed to be lower than diesel at full load, whereas for B100 it is higher at all loads. On the other hand, BSFC and NOx of MEMSO biodiesel blends are found to be higher than diesel. It is found that the combustion characteristics of all blends of methyl ester of mango seed oil showed similar trends with those of the baseline diesel. From this study, it is concluded that optimized blend is B25 and could be used as a viable alternative fuel in a single cylinder direct injection diesel engine without any modifications.

Oxidative stress, genotoxicity, and vascular cell adhesion molecule expression in cells exposed to particulate matter from combustion of conventional diesel and methyl ester biodiesel blends

DEFF Research Database (Denmark)

Hemmingsen, Jette Gjerke; Møller, Peter; Nøjgaard, Jakob Klenø

2011-01-01

cells (HUVECs). Viability and production of reactive oxygen species (ROS) were investigated in all cell types. We collected particles from combustion of D(100) and 20% (w/w) blends of animal fat or rapeseed oil methyl esters in light-duty vehicle engines complying with Euro2 or Euro4 standards......Our aim was to compare hazards of particles from combustion of biodiesel blends and conventional diesel (D(100)) in old and improved engines. We determined DNA damage in A549 cells, mRNA levels of CCL2 and IL8 in THP-1 cells, and expression of ICAM-1 and VCAM-1 in human umbilical cord endothelial....... Particles emitted from the Euro4 engine were smaller in size and more potent than particles emitted from the Euro2 engine with respect to ROS production and DNA damage, but similarly potent concerning cytokine mRNA expression. Particles emitted from combustion of biodiesel blends were larger in size...

Microwave-assisted methyl esters synthesis of Kapok (Ceiba pentandra seed oil: parametric and optimization study

Directory of Open Access Journals (Sweden)

Awais Bokhari

2015-09-01

Full Text Available The depleting fossil fuel reserves and increasing environmental concerns have continued to stimulate research into biodiesel as a green fuel alternative produced from renewable resources. In this study, Kapok (Ceiba pentandra oil methyl ester was produced by using microwave-assisted technique. The optimum operating conditions for the microwave-assisted transesterification of Kapok seed oil including temperature, catalyst loading, methanol to oil molar ratio, and irradiation time were investigated by using Response Surface Methodology (RSM based on Central Composite Design (CCD. A maximum conversion of 98.9 % was obtained under optimum conditions of 57.09 °C reaction temperature, 2.15 wt% catalyst (KOH loading, oil to methanol molar ratio of 1:9.85, and reaction time of 3.29 min. Fourier Transform Infra-Red (FT-IR spectroscopy was performed to verify the conversion of the fatty acid into methyl esters. The properties of Kapok oil methyl ester produced under the optimum conditions were characterized and found in agreement with the international ASTM D 6751 and EN 14214 standards.

Evaluation and Characterization of Biodiesels Obtained Through Ethylic or Methylic Transesterification of Tryacylglicerides in Corn Oil

Directory of Open Access Journals (Sweden)

Douglas Queiroz Santos

2014-06-01

Full Text Available This work was devoted to the transesterification of corn oil either with methyl or ethyl alcohol and to the characterization of the biodiesels (composed by FAME—fatty acid methyl esters—or FAEE—fatty acid ethyl esters, respectively produced. As an initial hypothesis, it was argued whether or not the two alcohols, both with short molecular chains, would impart significant differences to the chemical characteristics of the two biodiesels from corn oil. The most common properties of the biodiesels were evaluated by determining corresponding parameters for acid value, peroxide value, water content, oxidative stability, free and total glycerin, kinematic viscosity at 40 ℃ and density at 20 ℃, for both chemical routes, FAME and FAEE. In general, values were found to be well within the recommended limits for commercial biodiesel, in accordance with the Brazilian, European and American standard recommendations, except only for the oxidative stability. The methyl biodiesel presented acidity of 0.08 mg KOH/g; peroxide index, 23.77 meq/kg; oxidation stability, 3.10 h; water content, 297.1 mg/kg; total glycerin, 0.092 %; free glycerin, 0.009 %; viscosity, 4.05 mm2/s and density, 878.7 kg/m. The methyl biodiesel presented acidity of 0.11 mg/ KOH; peroxide index, 22.39 meq/kg; oxidation stability, 2.13 h; water content, 264.8 mg/kg; total glycerin, 0.25 %; free glycerin, 0.02 %; viscosity, 4.37 mm2/s and density, 874.0 kg/m. From a direct inspection of chemical data for the two products prepared via the two chemical routes, it can be drawn that values of the physical and chemical parameters for both, methyl and ethyl biodiesels, are essentially similar, except for the oxidative stability. However, the oxidative stability can be suitably adjusted by adding an anti-oxidizing agent to the ethyl biodiesel medium. The two biodiesels are thus promising alternatives to fully replace or to be admixed to the mineral diesel. Relatively to the pure petrol

Shock tube studies of methyl butanoate pyrolysis with relevance to biodiesel

KAUST Repository

Farooq, Aamir

2012-11-01

Methyl butanoate pyrolysis and decomposition pathways were studied in detail by measuring concentration time-histories of CO, CO 2, CH 3, and C 2H 4 using shock tube/laser absorption methods. Experiments were conducted behind reflected shock waves at temperatures of 1200-1800K and pressures near 1.5atm using mixtures of 0.1%, 0.5%, and 1% methyl butanoate in Argon. A novel laser diagnostic was developed to measure CO in the ν 1 fundamental vibrational band near 4.56μm using a new generation of quantum-cascade lasers. Wavelength modulation spectroscopy with second-harmonic detection (WMS-2f) was used to measure CO 2 near 2752nm. Methyl radical was measured using UV laser absorption near 216nm, and ethylene was monitored using IR gas laser absorption near 10.53μm. An accurate methyl butanoate model is critical in the development of mechanisms for larger methyl esters, and the measured time-histories provide kinetic targets and strong constraints for the refinement of the methyl butanoate reaction mechanism. Measured CO mole fractions reach plateau values that are the same as the initial fuel mole fraction at temperatures higher than 1500K over the maximum measurement time of 2ms or less. Two recent kinetic mechanisms are compared with the measured data and the possible reasons for this 1:1 ratio between MB and CO are discussed. Based on these discussions, it is expected that similar CO/fuel and CO 2/fuel ratios for biodiesel molecules, particularly saturated components of biodiesel, should occur. © 2012 The Combustion Institute.

Rhazya stricta Decne seed oil as an alternative, non-conventional feedstock for biodiesel production

International Nuclear Information System (INIS)

Nehdi, Imededdine Arbi; Sbihi, Hassen Mohamed; Al-Resayes, Saud Ibrahim

2014-01-01

Highlights: • First report of Rhazia stricta seed oil as feedstock for biodiesel production. • Biodiesel is prepared by alkaline transesterification. • Biodiesel from R. stricta oil meets specifications in biodiesel standards. - Abstract: Rhazya stricta Decne (R. stricta) is a hardy, drought-resistant, and arid land plant that is widely distributed from the Middle East to South Asia. The aim of this study was to evaluate the use of R. stricta seed oil as an alternative source of triacylglycerols that may be suitable for the synthesis of biodiesel. The oil content of the seeds was approximately 14% and was mainly composed of the fatty acids linoleic (60.95%) and oleic (25.48%) acid. R. stricta methyl esters (RSME) were prepared by a base-catalyzed transesterification reaction. The conversion rate of the triacylglycerols to the corresponding methyl esters was determined by 1 H-NMR to be approximately 97%. This study showed that the fuel properties of the RSMEs are comparable to other vegetable oil methyl esters that are commonly used as biodiesels. R. stricta plantations will therefore be suitable for promoting sustainable agriculture and for producing biodiesel with viable prices in arid and semi-arid regions throughout the world

Exact estimation of biodiesel cetane number (CN) from its fatty acid methyl esters (FAMEs) profile using partial least square (PLS) adapted by artificial neural network (ANN)

International Nuclear Information System (INIS)

Hosseinpour, Soleiman; Aghbashlo, Mortaza; Tabatabaei, Meisam; Khalife, Esmail

2016-01-01

Highlights: • Estimating the biodiesel CN from its FAMEs profile using ANN-based PLS approach. • Comparing the capability of ANN-adapted PLS approach with the standard PLS model. • Exact prediction of biodiesel CN from it FAMEs profile using ANN-based PLS method. • Developing an easy-to-use software using ANN-PLS model for computing the biodiesel CN. - Abstract: Cetane number (CN) is among the most important properties of biodiesel because it quantifies combustion speed or in better words, ignition quality. Experimental measurement of biodiesel CN is rather laborious and expensive. However, the high proportionality of biodiesel fatty acid methyl esters (FAMEs) profile with its CN is very appealing to develop straightforward and inexpensive computerized tools for biodiesel CN estimation. Unfortunately, correlating the chemical structure of biodiesel to its CN using conventional statistical and mathematical approaches is very difficult. To solve this issue, partial least square (PLS) adapted by artificial neural network (ANN) was introduced and examined herein as an innovative approach for the exact estimation of biodiesel CN from its FAMEs profile. In the proposed approach, ANN paradigm was used for modeling the inner relation between the input and the output PLS score vectors. In addition, the capability of the developed method in predicting the biodiesel CN was compared with the basal PLS method. The accuracy of the developed approaches for computing the biodiesel CN was assessed using three statistical criteria, i.e., coefficient of determination (R"2), mean-squared error (MSE), and percentage error (PE). The ANN-adapted PLS method predicted the biodiesel CN with an R"2 value higher than 0.99 demonstrating the fidelity of the developed model over the classical PLS method with a markedly lower R"2 value of about 0.85. In order to facilitate the use of the proposed model, an easy-to-use computer program was also developed on the basis of ANN-adapted PLS

Experimental Study on the Production of Karanja Oil Methyl Ester and Its Effect on Diesel Engine

Directory of Open Access Journals (Sweden)

N Shrivastava

2012-11-01

Full Text Available Fast depletion of fossil fuel resources forces the extensive research on the alternative fuels. Vegetable oils edible or non edible can be a better substitute for the petroleum diesel. Karanja, a non edible oil can be a potential source to replace the diesel fuel. To investigate the feasibility of Karanja oil as an alternative diesel fuel, its biodiesel was prepared through the transesterification process. The Biodiesel was then subjected to performance and emission tests in order to assess its actual performance, when used as a diesel engine fuel. The data generated for the 20, 50 and 100 percent blended biodiesel were compared with base line data generated for neat diesel fuel. Result showed that the Biodiesel and its blend showed lower thermal efficiency. Emission of Carbon monoxide, unburned Hydrocarbon and smoke was found to be reduced where as oxides of nitrogen was higher with biodiesel and its blends. Keywords: alternate Diesel fuel; Biodiesel; Karanja oil methyl ester; performance and emission

Glycerol extracting dealcoholization for the biodiesel separation process.

Science.gov (United States)

Ye, Jianchu; Sha, Yong; Zhang, Yun; Yuan, Yunlong; Wu, Housheng

2011-04-01

By means of utilizing sunflower oil and Jatropha oil as raw oil respectively, the biodiesel transesterification production and the multi-stage extracting separation were carried out experimentally. Results indicate that dealcoholized crude glycerol can be utilized as the extracting agent to achieve effective separation of methanol from the methyl ester phase, and the glycerol content in the dealcoholized methyl esters is as low as 0.02 wt.%. For the biodiesel separation process utilizing glycerol extracting dealcoholization, its technical and equipment information were acquired through the rigorous process simulation in contrast to the traditional biodiesel distillation separation process, and results show that its energy consumption decrease about 35% in contrast to that of the distillation separation process. The glycerol extracting dealcoholization has sufficient feasibility and superiority for the biodiesel separation process. Copyright © 2011 Elsevier Ltd. All rights reserved.

Process parameters optimization for synthesis of methyl ester from sunflower oil using Taguchi technique

Directory of Open Access Journals (Sweden)

G. Senthilkumar

2014-09-01

Full Text Available In this work, transesterification of sunflower oil for obtaining biodiesel was studied. Taguchi’s methodology (L9 orthogonal array was selected to optimize the most significant variables (methanol, catalyst concentration and stirrer speed in transesterification process. Experiments have conducted based on development of L9 orthogonal array by using Taguchi technique. Analysis of Variance (ANOVA and the regression equations were used to find the optimum yield of sunflower methyl ester under the influence of methanol, catalyst & stirrer speed. The study resulted in a maximum yield of sun flower methyl ester as 96% with the optimal conditions of methanol 110 ml with 0.5% by wt. of sodium hydroxide (NaOH stirred at 1200 rpm. The yield was analyzed on the basis of “larger is better”. Finally, confirmation tests were carried out to verify the experimental results.

Production of biodiesel from Coelastrella sp. microalgae

Science.gov (United States)

Mansur, Dieni; Fitriady, Muhammad Arifuddin; Susilaningsih, Dwi; Simanungkalit, Sabar Pangihutan

2017-11-01

Microalgae have a wide area of usage and one of them it can be used for biodiesel production. In biodiesel production, lipids containing triglyceride or free fatty acid are converted into methyl ester through trans/esterification reactions. Lipids from microalgae can be extracted by acetone and dimethyl carbonate using homogenizer. Esterification of the lipids was investigated using various catalysts and source of methyl group. Activity of homogeneous catalyst such as HCl and H2SO4 and heterogeneous catalysts such as montmorillonit K-10 and ledgestone was investigated. Moreover, methanol and dimethyl carbonate as source of methyl group were also studied. Among of catalysts with methanol as source of methyl group, it was found that yield of crude biodiesel derived from Choelestrella Sp. microalgae was high over H2SO4 catalyst. On the other hand, over H2SO4 catalyst using dimethyl carbonate as source of methyl group, yield of crude biodiesel significant increase. However, FAME composition of crude biodiesel was high over HCl catalyst.

An experimental study on performance and exhaust emissions of a diesel engine fuelled with tobacco seed oil methyl ester

International Nuclear Information System (INIS)

Usta, N.

2005-01-01

Tobacco seeds are a by product of tobacco leaves production. To the author's best knowledge, unlike tobacco leaves, tobacco seeds are not collected from fields and are not commercial products. However, tobacco seeds contain significant amounts of oil. Although tobacco seed oil is a non-edible vegetable oil, it can be utilized for biodiesel production as a new renewable alternative diesel engine fuel. In this study, an experimental study on the performance and exhaust emissions of a turbocharged indirect injection diesel engine fuelled with tobacco seed oil methyl ester was performed at full and partial loads. The results showed that the addition of tobacco seed oil methyl ester to the diesel fuel reduced CO and SO 2 emissions while causing slightly higher NO x emissions. Meanwhile, it was found that the power and the efficiency increased slightly with the addition of tobacco seed oil methyl ester. (Author)

Isolation and characterization of fatty acid methyl ester (FAME)-producing Streptomyces sp. S161 from sheep (Ovis aries) faeces.

Science.gov (United States)

Lu, Y; Wang, J; Deng, Z; Wu, H; Deng, Q; Tan, H; Cao, L

2013-09-01

An actinomycete producing oil-like mixtures was isolated and characterized. The strain was isolated from sheep faeces and identified as Streptomyces sp. S161 based on 16S rRNA gene sequence analysis. The strain showed cellulase and xylanase activities. The (1) H nuclear magnetic resonance (NMR) spectra of the mixtures showed that the mixtures were composed of fatty acid methyl esters (52·5), triglycerides (13·7) and monoglycerides (9·1) (mol.%). Based on the gas chromatography-mass spectrometry (GC-MS) analysis, the fatty acid methyl esters were mainly composed of C14-C16 long-chain fatty acids. The results indicated that Streptomyces sp. S161 could produce fatty acid methyl esters (FAME) directly from starch. To our knowledge, this is the first isolated strain that can produce biodiesel (FAME) directly from starch. © 2013 The Society for Applied Microbiology.

Biodiesel production from inedible animal tallow and an experimental investigation of its use as alternative fuel in a direct injection diesel engine

International Nuclear Information System (INIS)

Oener, Cengiz; Altun, Sehmus

2009-01-01

In this study, a substitute fuel for diesel engines was produced from inedible animal tallow and its usability was investigated as pure biodiesel and its blends with petroleum diesel fuel in a diesel engine. Tallow methyl ester as biodiesel fuel was prepared by base-catalyzed transesterification of the fat with methanol in the presence of NaOH as catalyst. Fuel properties of methyl ester, diesel fuel and blends of them (5%, 20% and 50% by volume) were determined. Viscosity and density of fatty acid methyl ester have been found to meet ASTM D6751 and EN 14214 specifications. Viscosity and density of tallow methyl esters are found to be very close to that of diesel. The calorific value of biodiesel is found to be slightly lower than that of diesel. An experimental study was carried out in order to investigate of its usability as alternative fuel of tallow methyl ester in a direct injection diesel engine. It was observed that the addition of biodiesel to the diesel fuel decreases the effective efficiency of engine and increases the specific fuel consumption. This is due to the lower heating value of biodiesel compared to diesel fuel. However, the effective engine power was comparable by biodiesel compared with diesel fuel. Emissions of carbon monoxide (CO), oxides of nitrogen (NO x ), sulphur dioxide (SO 2 ) and smoke opacity were reduced around 15%, 38.5%, 72.7% and 56.8%, respectively, in case of tallow methyl esters (B100) compared to diesel fuel. Besides, the lowest CO, NO x emissions and the highest exhaust temperature were obtained for B20 among all other fuels. The reductions in exhaust emissions made tallow methyl esters and its blends, especially B20 a suitable alternative fuel for diesel and thus could help in controlling air pollution. Based on this study, animal tallow methyl esters and its blends with petroleum diesel fuel can be used a substitute for diesel in direct injection diesel engines without any engine modification. (author)

The effects of pH in profile of lipid and ester accumulation of arthrospira platensis (spirulina) as a potential source of biodiesel

International Nuclear Information System (INIS)

Reyes, Patrick A.; Ybañez, Manolito G. Jr.; Avilla, Ruel A.

2013-01-01

This study aimed to produce biodiesel (ester-based fuel) using the extracts of microalgae Arthrospira platensis (Spirulina). Specifically, the research focused in determining effect of pH in culturing the Spirulina and its lipid accumulation; determining the constituents present in the lipid extracts; and determining the methyl esters in the transesterified lipids. The best pH condition in culturing the algal sample was found to be at pH 10 to 11. Analysis of the extracted lipid samples revealed that pH condition in culturing medium has a significant effect on the lipid accumulation in Spirulina. Perkin Elmer Claurus 500 GC-MS system elucidated that the constituents present in the experimental samples were esterified lipids. The esters were derived from butanoic, hexadeanoic and octadecanoic acid. About 19 free fatty acids out of 23 determined compounds present were from the controlled sample which suggests that these were main precursors of the esters found in the sample were butyl, allyl nonyl, propyl tetradecyl, methylpropyl, allyl dodecyl, hexyl pentadecyl, dodecyl propyl, heptyl esters with the parent chain of fatty acids enumerated above. These showed that pH manipulations could be used as a direct transesterification of fatty acids in producing biodiesels. (author)

Comparison of transesterification methods for production of biodiesel from vegetable oils and fats

International Nuclear Information System (INIS)

Demirbas, Ayhan

2008-01-01

Comparative studies on transesterification methods were presented in this work. Biodiesel is obtained from a chemical reaction called transesterification (ester exchange). The reaction converts esters from long chain fatty acids into mono alkyl esters. Chemically, biodiesel commonly is a fatty acid methyl ester. Vegetable oils can be transesterified by heating them with a large excess of anhydrous methanol and an acidic or basic reagent as catalyst. A catalyst is usually used to improve the reaction rate and yield. In a transesterification reaction, a larger amount of methanol was used to shift the reaction equilibrium to the right side and produce more methyl esters as the proposed product. Several aspects including the type of catalyst (alkaline, acid or enzyme), alcohol/vegetable oil molar ratio, temperature, purity of the reactants (mainly water content) and free fatty acid content have an influence on the course of the transesterification. A non-catalytic biodiesel production route with supercritical methanol has been developed that allows a simple process and high yield because of the simultaneous transesterification of triglycerides and methyl esterification of fatty acids. In the catalytic supercritical methanol transesterification method, the yield of conversion rises to 60-90% for the first 1 min

Optimization of biodiesel production from Chlorella protothecoides oil via ultrasound assisted transesterification

Directory of Open Access Journals (Sweden)

Özçimen Didem

2017-01-01

Full Text Available There is a growing interest in biodiesel as an alternative fuel for diesel engines because of the high oil prices and environmental issues related to massive greenhouse gas emissions. Nowadays, microalgal biomass has become a promising biodiesel feedstock. However, traditional biodiesel production from microalgae consumes a lot of energy and solvents. It is necessary to use an alternative method that can reduce the energy and alcohol consumption and save time. In this study, biodiesel production from Chlorella protothecoides oil by ultrasound assisted transesterification was conducted and effects of reaction parameters such as methanol:oil ratio, catalyst/oil ratio and reaction time on fatty acid methyl ester yields were investigated. The transesterification reactions were carried out by using methanol as alcohol and potassium hydroxide as the catalyst. The highest methyl ester production was obtained under the conditions of 9:1 methanol/oil mole ratio, 1.5% potassium hydroxide catalyst in oil, and for reaction time of 40 min. It was also found that catalyst/oil molar ratio was the most effective parameter on methyl ester yield according to statistical data. The results showed that ultrasound-assisted transesterification may be an alternative and cost effective way to produce biodiesel efficiently.

Transesterification Of Kapok Oil Using Calcium Oxide Catalyst Methyl Esters Yield With Catalyst Loading

Directory of Open Access Journals (Sweden)

Yunusa Tukur

2015-08-01

Full Text Available Abstract This investigation was necessitated to find other feedstocks for biodiesel production that would not compete with food. Kapok oil with 0.8 FFA was transesterified with methanol using a heterogeneous catalyst CaO to determine its potential for biodiesel production. Methyl esters yields of 70.4 65.6 78.2 71.9 and 72.5 were obtained with catalyst loading of 0.8 1.2 1.6 2.0 and 2.4 wt. of oil. The products had high compositions of FFA and alcohols which indicates that the oil require more esterification to reduce the feedstock FFA far below 0.8. Some unsaturated hydrocarbons such as alkenes and alkynes were also formed which could make the products unstable.

Aerobic Biodegradation Kinetics And Mineralization Of Six Petrodiesel/Soybean-Biodiesel Blends

Science.gov (United States)

The aerobic biodegradation kinetics and mineralization of six petrodiesel/soybean-biodiesel blends (B0, B20, B40, B60, B80, and B100), where B100 is 100% biodiesel, were investigated by acclimated cultures. The fatty acid methyl esters (FAMEs) of biodiesel were found to undergo ...

Progress and recent trends in biodiesel fuels

International Nuclear Information System (INIS)

Demirbas, Ayhan

2009-01-01

Fossil fuel resources are decreasing daily. Biodiesel fuels are attracting increasing attention worldwide as blending components or direct replacements for diesel fuel in vehicle engines. Biodiesel fuel typically comprises lower alkyl fatty acid (chain length C 14 -C 22 ), esters of short-chain alcohols, primarily, methanol or ethanol. Various methods have been reported for the production of biodiesel from vegetable oil, such as direct use and blending, microemulsification, pyrolysis, and transesterification. Among these, transesterification is an attractive and widely accepted technique. The purpose of the transesterification process is to lower the viscosity of the oil. The most important variables affecting methyl ester yield during the transesterification reaction are the molar ratio of alcohol to vegetable oil and the reaction temperature. Methanol is the commonly used alcohol in this process, due in part to its low cost. Methyl esters of vegetable oils have several outstanding advantages over other new-renewable and clean engine fuel alternatives. Biodiesel fuel is a renewable substitute fuel for petroleum diesel or petrodiesel fuel made from vegetable or animal fats; it can be used in any mixture with petrodiesel fuel, as it has very similar characteristics, but it has lower exhaust emissions. Biodiesel fuel has better properties than petrodiesel fuel; it is renewable, biodegradable, non-toxic, and essentially free of sulfur and aromatics. Biodiesel seems to be a realistic fuel for future; it has become more attractive recently because of its environmental benefits. Biodiesel is an environmentally friendly fuel that can be used in any diesel engine without modification

Use of residual soapstock from the refining of edible vegetable oils to make biodiesel; Aprovechamiento de las oleinas residuales procedentes del proceso de refinado de los aceites vegetales comestibles, para la fabricaciond e biodiesel

Energy Technology Data Exchange (ETDEWEB)

Marin, P.; Barriga Mateos, F.; Alvarez Mateos, P. [Universidad de Sevilla (Spain)

2003-07-01

A procedure to obtain Biodiesel from Oiliness is studied. Biodiesel is a suitable product to replace diesel oil currently used to power the Diesel engines. It consists of a mixture of methyl esters of the fatty acids presents as triglycerides in vegetables oils (oil, sunflower, soya, rape oils). As a result of the refining of these oils for their use as food, a waste product is formed, the oleins (acidulated soapstock). The oiliness consist of a mixture of triglycerides and free fatty acids, the latter amounting to 50% or more of the mixture and are subject to a fluctuating market, therefore it exist at times a problem for their disposal. In our research work we have tried to obtain biodiesel from oiliness. The process resulting from our experimental work is as follows. 1. Scarification of the free fatty acids with methanol, by acid catalysis, centrifuging the reaction product and removal of the acid-methanol phase. Drying of the latter. At this stage we have a product containing about 70% of methyl esters. 2. Transesterification of the triglycerides present in the sterified product with methanol by alkaline catalysis, washing the reaction product with a water methanol solution. Centrifuging and removal of the water-methanol phase. At this stage a biodiesel products is obtained containing about 90% of methyl esters. 3. Fractional vacuum distillation of the 90% biodiesel gives a final product with a methyl esters content higher than 98%. (Author)

COMBUSTION CHARACTERISTICS OF DIESEL ENGINE OPERATING ON JATROPHA OIL METHYL ESTER

Directory of Open Access Journals (Sweden)

Doddayaraganalu Amasegoda Dhananjaya

2010-01-01

Full Text Available Fuel crisis because of dramatic increase in vehicular population and environmental concerns have renewed interest of scientific community to look for alternative fuels of bio-origin such as vegetable oils. Vegetable oils can be produced from forests, vegetable oil crops, and oil bearing biomass materials. Non-edible vegetable oils such as jatropha oil, linseed oil, mahua oil, rice bran oil, karanji oil, etc., are potentially effective diesel substitute. Vegetable oils have reasonable energy content. Biodiesel can be used in its pure form or can be blended with diesel to form different blends. It can be used in diesel engines with very little or no engine modifications. This is because it has combustion characteristics similar to petroleum diesel. The current paper reports a study carried out to investigate the combustion, performance and emission characteristics of jatropha oil methyl ester and its blend B20 (80% petroleum diesel and 20% jatropha oil methyl ester and diesel fuel on a single-cylinder, four-stroke, direct injections, water cooled diesel engine. This study gives the comparative measures of brake thermal efficiency, brake specific energy consumption, smoke opacity, HC, NOx, ignition delay, cylinder peak pressure, and peak heat release rates. The engine performance in terms of higher thermal efficiency and lower emissions of blend B20 fuel operation was observed and compared with jatropha oil methyl ester and petroleum diesel fuel for injection timing of 20° bTDC, 23° bTDC and 26° bTDC at injection opening pressure of 220 bar.

Functional expression and characterization of five wax ester synthases in Saccharomyces cerevisiae and their utility for biodiesel production

Directory of Open Access Journals (Sweden)

Shi Shuobo

2012-02-01

Full Text Available Abstract Background Wax ester synthases (WSs can synthesize wax esters from alcohols and fatty acyl coenzyme A thioesters. The knowledge of the preferred substrates for each WS allows the use of yeast cells for the production of wax esters that are high-value materials and can be used in a variety of industrial applications. The products of WSs include fatty acid ethyl esters, which can be directly used as biodiesel. Results Here, heterologous WSs derived from five different organisms were successfully expressed and evaluated for their substrate preference in Saccharomyces cerevisiae. We investigated the potential of the different WSs for biodiesel (that is, fatty acid ethyl esters production in S. cerevisiae. All investigated WSs, from Acinetobacter baylyi ADP1, Marinobacter hydrocarbonoclasticus DSM 8798, Rhodococcus opacus PD630, Mus musculus C57BL/6 and Psychrobacter arcticus 273-4, have different substrate specificities, but they can all lead to the formation of biodiesel. The best biodiesel producing strain was found to be the one expressing WS from M. hydrocarbonoclasticus DSM 8798 that resulted in a biodiesel titer of 6.3 mg/L. To further enhance biodiesel production, acetyl coenzyme A carboxylase was up-regulated, which resulted in a 30% increase in biodiesel production. Conclusions Five WSs from different species were functionally expressed and their substrate preference characterized in S. cerevisiae, thus constructing cell factories for the production of specific kinds of wax ester. WS from M. hydrocarbonoclasticus showed the highest preference for ethanol compared to the other WSs, and could permit the engineered S. cerevisiae to produce biodiesel.

Transesterified milkweed (Asclepias) seed oil as a biodiesel fuel

Energy Technology Data Exchange (ETDEWEB)

Ronald Alan Holser; Rogers Harry-O' Kurua [United States Department of Agriculture, Peoria, IL (United States). Agricultural Research Service, National Center for Utilization Research

2006-10-15

The methyl and ethyl esters of milkweed (Asclepias) seed oil were prepared and compared to soybean esters in laboratory tests to determine biodiesel fuel performance properties. The pour points of the methyl and ethyl milkweed esters measured -6{sup o}C and -10{sup o}C, respectively, which is consistent with the high levels of unsaturation characteristic of milkweed seed oil. The oxidative stabilities measured by OSI at 100{sup o}C were between 0.8 and 4.1 h for all samples tested. The kinematic viscosities determined at 40{sup o}C by ASTM D 445 averaged 4.9 mm{sup 2}/s for milkweed methyl esters and 4.2 mm{sup 2}/s for soybean methyl esters. Lubricity values determined by ASTM D 6079 at 60{sup o}C were comparable to the corresponding soybean esters with average ball wear scar values of 118 {mu}m for milkweed methyl esters and 200 {mu}m for milkweed ethyl esters.

Identification and fingerprinting of biodiesel blends by solid phase extraction and gas chromatography-mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Yang, Z. [Environment Canada, Ottawa, ON (Canada). Emergencies Science and Technology Section, Emergencies, Operational Analytical Laboratories and Research Support Division; China Univ. of Geosciences, Wuhan (China). School of Environmental Studies; Hollebone, B.; Wang, Z.; Yang, C.; Landriault, M. [Environment Canada, Ottawa, ON (Canada). Emergencies Science and Technology Section, Emergencies, Operational Analytical Laboratories and Research Support Division

2009-07-01

Interest in biodiesel as a replacement for petroleum diesel fuel is growing. In North America, biodiesels are produced by the methyl esterification of plant and animal triglycerides, resulting in complex mixtures composed of fatty acid methyl esters (FAMEs). It is important for both environmental forensic and remediation purposes to determine diesel and biodiesel origins, and the biodiesel content when it is blended with conventional petroleum diesel. This paper reported on a study that combined 2 methods to determine biodiesel levels in blended fuels. Micro-column fractionation of FAMEs involving solid phase extraction (SPE) was combined with gas chromatography-mass spectrometry (GC/MS) to achieve detailed chemical fingerprinting of blends, including the identification and quantification of individual aliphatic hydrocarbons, aromatic hydrocarbons, fatty acid alkyl esters, and free sterols. Fractionation of the fuel samples was optimized for separation of fatty acid esters, free sterols from petroleum hydrocarbons into 4 fractions, notably aliphatic, aromatic, fatty-acid ester and polar components. A sum of the FAME components was used to determine an unknown blend level in freshly-prepared samples. This study showed that this method has great potential for identifying biodiesel in diesel fuel blends and could form the basis of a method for biodiesel-contaminated environmental samples. 28 refs., 5 tabs., 4 figs.

Identification and fingerprinting of biodiesel blends by solid phase extraction and gas chromatography-mass spectrometry

International Nuclear Information System (INIS)

Yang, Z.; China Univ. of Geosciences, Wuhan; Hollebone, B.; Wang, Z.; Yang, C.; Landriault, M.

2009-01-01

Interest in biodiesel as a replacement for petroleum diesel fuel is growing. In North America, biodiesels are produced by the methyl esterification of plant and animal triglycerides, resulting in complex mixtures composed of fatty acid methyl esters (FAMEs). It is important for both environmental forensic and remediation purposes to determine diesel and biodiesel origins, and the biodiesel content when it is blended with conventional petroleum diesel. This paper reported on a study that combined 2 methods to determine biodiesel levels in blended fuels. Micro-column fractionation of FAMEs involving solid phase extraction (SPE) was combined with gas chromatography-mass spectrometry (GC/MS) to achieve detailed chemical fingerprinting of blends, including the identification and quantification of individual aliphatic hydrocarbons, aromatic hydrocarbons, fatty acid alkyl esters, and free sterols. Fractionation of the fuel samples was optimized for separation of fatty acid esters, free sterols from petroleum hydrocarbons into 4 fractions, notably aliphatic, aromatic, fatty-acid ester and polar components. A sum of the FAME components was used to determine an unknown blend level in freshly-prepared samples. This study showed that this method has great potential for identifying biodiesel in diesel fuel blends and could form the basis of a method for biodiesel-contaminated environmental samples. 28 refs., 5 tabs., 4 figs.

Usage of methyl ester of tall oil fatty acids and resinic acids as alternative diesel fuel

International Nuclear Information System (INIS)

Keskin, Ali; Yasar, Abdulkadir; Guerue, Metin; Altiparmak, Duran

2010-01-01

In the experimental study, tall oil fatty and resinic acids were investigated as alternative diesel fuels. The fatty acids, obtained by distilling the crude tall oil, were esterified with methanol in order to obtain tall oil methyl ester (biodiesel). Blends of the methyl ester, resinic acids and diesel fuel were prepared for test fuels. Performance and emission tests of the test fuels were carried out in an unmodified direct injection diesel engine on full load conditions. The results showed that the specific fuel consumption (SFC) with the blend fuels did not show a significant change. CO emission and smoke level decreased up to 23.91% and 19.40%, respectively. In general, NO x emissions showed on trend of increasing with the blend fuels (up to 25.42%). CO 2 emissions did not vary with the blend fuels significantly.

Usage of methyl ester of tall oil fatty acids and resinic acids as alternative diesel fuel

Energy Technology Data Exchange (ETDEWEB)

Keskin, Ali; Yasar, Abdulkadir [Tarsus Technical Education Faculty, Mersin University, 33500 Mersin (Turkey); Guerue, Metin [Engineering and Architectural Faculty, Gazi University, 06570 Maltepe, Ankara (Turkey); Altiparmak, Duran [Technical Education Faculty, Gazi University, 06500 Ankara (Turkey)

2010-12-15

In the experimental study, tall oil fatty and resinic acids were investigated as alternative diesel fuels. The fatty acids, obtained by distilling the crude tall oil, were esterified with methanol in order to obtain tall oil methyl ester (biodiesel). Blends of the methyl ester, resinic acids and diesel fuel were prepared for test fuels. Performance and emission tests of the test fuels were carried out in an unmodified direct injection diesel engine on full load conditions. The results showed that the specific fuel consumption (SFC) with the blend fuels did not show a significant change. CO emission and smoke level decreased up to 23.91% and 19.40%, respectively. In general, NO{sub x} emissions showed on trend of increasing with the blend fuels (up to 25.42%). CO{sub 2} emissions did not vary with the blend fuels significantly. (author)

Cetane Number of Biodiesel from Karaya Oil

KAUST Repository

Wasfi, Bayan

2017-04-01

Biodiesel is a renewable fuel alternative to petroleum Diesel, biodiesel has similar characteristic but with lesser exhaust emission. In this study, transesterification of Karaya oil is examined experimentally using a batch reactor at 100-140°C and 5 bar in subcritical methanol conditions, residence time from 10 to 20 minutes, using a mass ratio 6 methanol-to-vegetable oil. Methanol is used for alcoholysis and sodium hydroxide as a catalyst. Experiments varied the temperature and pressure, observing the effect on the yield and reaction time. In addition, biodiesel from corn oil was created and compared to biodiesel from karaya oil. Kinetic model proposed. The model estimates the concentration of triglycerides, diglycerides, monoglycerides and methyl esters during the reaction. The experiments are carried out at temperatures of 100°C and above. The conversion rate and composition of methyl esters produced from vegetable oils are determined by Gas Chromatography Analysis. It was found that the higher the temperature, the higher reaction rate. Highest yield is 97% at T=140°C achieved in 13 minutes, whereas at T=100°C yield is 68% in the same time interval. Ignition Quality Test (IQT) was utilized for determination of the ignition delay time (IDT) inside a combustion chamber. From the IDT cetane number CN inferred. In case of corn oil biodiesel, the IDT = 3.5 mS, leading to a CN = 58. Whereas karaya oil biodiesel showed IDT = 2.4 mS, leading to a CN = 97. The produced methyl esters were also characterized by measurements of viscosity (υ), density (ρ), flash point (FP) and heat of combustion (HC). The following properties observed: For corn biodiesel, υ = 8.8 mPa-s, ρ = 0.863 g/cm3, FP = 168.8 °C, and HC = 38 MJ/kg. For karaya biodiesel, υ = 10 mPa-s, ρ = 0.877 g/cm3, FP = 158.2 °C, and HC = 39 MJ/kg.

Environmentally friendly properties of vegetable oil methyl esters

Directory of Open Access Journals (Sweden)

Gateau Paul

2005-07-01

Full Text Available Measurements were carried out on Vegetable Oil Methyl Esters (VOME or FAME answering the most recent specifications. The products tested are RME (Rapeseed oil Methyl Ester, ERME (Erucic Rapeseed oil Methyl Esters, SME (Sunflower oil Methyl Esters, and HOSME (High Oleic Sunflower oil Methyl Esters. They contain more than 99.5% of fatty acid mono esters. The compositions are given. VOME are not volatile and they are not easily flammable. They are not soluble in water and they are biodegradable. According to the methods implemented for the determination of the German classification of substances hazardous to waters WGK, they are not toxic on mammals and unlike diesel fuel they are not toxic on fish, daphnia, algae and bacteria. The RME is not either toxic for shrimps. According to tests on rabbits, RME and SME are not irritating for the skin and the eyes. VOME display particularly attractive environmental properties.

Combustion of biodiesel fuel produced from hazelnut soapstock/waste sunflower oil mixture in a Diesel engine

International Nuclear Information System (INIS)

Usta, N.; Oeztuerk, E.; Can, Oe.; Conkur, E.S.; Nas, S.; Con, A.H.; Can, A.C.; Topcu, M.

2005-01-01

Biodiesel is considered as an alternative fuel to Diesel fuel No. 2, which can be generally produced from different kinds of vegetable oils. Since the prices of edible vegetable oils are higher than that of Diesel fuel No. 2, waste vegetable oils and non-edible crude vegetable oils are preferred as potential low priced biodiesel sources. In addition, it is possible to use soapstock, a by-product of edible oil production, for cheap biodiesel production. In this study, a methyl ester biodiesel was produced from a hazelnut soapstock/waste sunflower oil mixture using methanol, sulphuric acid and sodium hydroxide in a two stage process. The effects of the methyl ester addition to Diesel No. 2 on the performance and emissions of a four cycle, four cylinder, turbocharged indirect injection (IDI) Diesel engine were examined at both full and partial loads. Experimental results showed that the hazelnut soapstock/waste sunflower oil methyl ester can be partially substituted for the Diesel fuel at most operating conditions in terms of the performance parameters and emissions without any engine modification and preheating of the blends

Biodiesel in Belgium. From rapeseed oil to used vegetable oils

International Nuclear Information System (INIS)

Pelkmans, L.

1997-01-01

There are two motives for the search for alternative motor fuels: reducing the growing pressure of traffic on environment, and looking for a replacement for petrol and diesel oil that are bound to be worn-out in a few decades. A promising alternative motor fuel is biodiesel. The author's institute is involved in its second biodiesel demonstration project. In the first project RME (rapeseed methyl ester) was used undiluted in five passenger cars for two years. There were no technical problems and a clear environmental advantage was noticed. However, the price remains a problem. The use of waste vegetable oils for the production of biodiesel could help to overcome this problem. Therefore, a second biodiesel demonstration project was started in which UVOME (used vegetable oil methyl ester) is used. The preliminary results show a great similarity with the RME results and no technical problems in real life use. 1 fig., 1 tab., 5 refs

Production of Biodiesel from Thespesiapopulnea seed oil through rapid in situ transesterification - an optimization study and assay of fuel properties

Science.gov (United States)

Bhargavi, G.; Nageswara Rao, P.; Renganathan, S.

2018-03-01

Biodiesel production was carried out from Thespesia populnea seed oil through rapid insitu transesterification. Influence of reaction parameters such as catalyst type and concentration, methanol to biomass ratio, co-solvent volume, temperature and agitation speed on conversion of oil into methyl esters was investigated. The effect of different co-solvents on conversion was evaluated. Optimum methyl ester conversion of 97.80% was achieved at 1.5wt% of KOH catalyst, 5.5:1 (v/w) methanol to biomass ratio, 25vol%tetrahydrofuranco-solvent, 60°C and 500 rpm within 120min of reaction time. Fuel properties of produced methyl esters were well fitted within the limits of ASTMD 6751 standards. Considering the properties of produced biodiesel, Thespesia populnea seed derived biodiesel can be used as potential alternate to fossil diesel fuel.

Alternatif Pembuatan Biodiesel Melalui Transesterifikasi Minyak Castor (Ricinus communis Menggunakan Katalis Campuran Cangkang Telur Ayam dan Kaolin

Directory of Open Access Journals (Sweden)

Soni - Setiadji

2017-05-01

Full Text Available Biodiesel was produced by transesterification of castor oil (Ricinus communis using a catalyst of CaO and kaolin (CaO / kaolin had been performed. CaO was obtained from the calcination of eggshell. Castor oil is selected as biodiesel feedstock because it belongs to non-food oil and easy to cultivate. In general, the research method aims to comprise the CaO / Kaolin catalysts with a ratio of 15 mmol CaO per 1 gram of kaolin activated using impregnation method and biodiesel produced through transesterification of castor oil using the catalyst at 65 ºC for 8 hours with ratio of castor oil: methanol: catalyst (1: 15: 5% w / w. The reaction is carried out on the reflux system. The XRD analysis show the presence of silica and potassium aluminum silicate hydroxide in the catalyst. The EDS results show the catalyst-forming components CaO and silica. The FTIR analysis results show the absorption peak in the functional group forming the methyl ester compound. Based on the characterization of GC-MS, the largest methyl ester components contained in biodiesel are methyl risinoleate, methyl elaidat, methyl stearate, methyl linoleate, and methyl palmitate. The overall conversion of castor oil to methyl ester using CaO / kaolin catalyst is 97.36%. The largest component in castor oil is risinoleic acid, has been successfully converted to methyl risinoleate by 74.75%.DOI: http://dx.doi.org/10.15408/jkv.v0i0.4778

PENGOLAHAN BIJI MAHONI (Swietenia Macrophylla King SEBAGAI BAHAN BAKU ALTERNATIF BIODIESEL

Directory of Open Access Journals (Sweden)

Astrilia Damayanti

2013-05-01

Full Text Available Peningkatan kebutuhan minyak bumi yang terus menerus akan mengakibatkan kelangkaan bahan bakar minyak. Sumber energi alternatif yang ramah lingkungan, salah satunya adalah biodiesel. Bahan baku potensial untuk memproduksi biodiesel yang tidak bersaing dengan bahan baku pangan contohnya adalah biji mahoni (swietenia macrophylla king. Tahapan yang diperlukan dalam percobaan biodiesel adalah proses pengambilan minyak biji mahoni dengan proses penyangraian, degumming, dan proses transesterifikasi. Alat yang diperlukan dalam pembuatan biodiesel yaitu: labu alas bulat dilengkapi kondensor, gelas ukur, pengaduk magnetik, alat-alat gelas lab, dan lain sebagainya. Proses pengambilan minyak dilakukan dengan penyangraian yang hasilnya di degumming dengan asam fosfat 5% b/b pada suhu 80ºC selama 15 menit. Degumming bertujuan untuk menghilangkan getah, lendir, protein, resin dan gum. Proses kedua yaitu transesterifikasi dengan metanol 1:6 (minyak dan mtanol dengan KOH 0,1 N pada suhu 60ºC selama 1 jam. Setelah diperoleh metil ester, dilakukan proses pencucian atau penetralan metil ester pada suhu pemanasan 104ºC untuk menghilangkan kadar airnya. Dari hasil percobaan diperoleh rendemen minyak sebesar 86,92%, uji densitas 874,08 kg/m³, viskositas 3,07 mm2/s, dan bilangan asam 0,5601 mg KOH/g. Metil ester yang dihasilkan telah sesuai dengan SNI-04-7182-2006. An increased demand of the fossil fuel would lead to scarcity of the fossil fuel in the future. An alternative of environmentally friendly energy sources is biodiesel. It is accounted that the resources for producing biodiesel should not compete with food raw materials, such as mahogany grain, (swietenia macrophylla king. The necessary steps in the experiment of producing biodiesel are process of taking the mahogany seed-oil by using roasting method, degumming, and transesterification process. The required equipments for producing biodiesel were round-bottom flask equipped with condenser

Synthesis of biodiesel from castor oil: Silent versus sonicated methylation and energy studies

International Nuclear Information System (INIS)

Sáez-Bastante, J.; Pinzi, S.; Jiménez-Romero, F.J.; Luque de Castro, M.D.; Priego-Capote, F.; Dorado, M.P.

2015-01-01

Highlights: • Sonicated transesterification leads to higher conversion than conventional one. • Energy consumption required by conventional and ultrasound-assisted transesterification was compared. • Ultrasound-assisted methylation is more competitive in terms of energy than conventional one. - Abstract: In recent years, biodiesel is evolving to be one of the most employed biofuels for partial replacement of petrodiesel. The most widely used feedstocks for biodiesel production are vegetable oils. Among them, castor oil presents two interesting features as biodiesel raw material; on one hand, it does not compete with edible oils; on the other, the cultivar does not require high inputs. In this research, a comparison between conventional and ultrasound-assisted transesterification was carried out in terms of castor oil methyl ester (COME) yield and energy efficiency. Results show that sonicated transesterification leads to higher COME yields under lower methanol-to-oil molar ratio, lower amount of catalyst, shorter reaction time and lower amount of energy required. Ultrasound-assisted transesterification parameters were optimized resulting in the following optimum conditions: 20 kHz fixed frequency, 70% duty cycle, 40% sonication amplitude, 4.87 methanol-to-oil molar ratio, 1.4% w/w amount of catalyst and 3 sonication cycles (3 min 48 s) that provided 86.57% w/w COME yield. The energy required along each type of transesterification was measured leading to the conclusion that sonicated transesterification consumes a significant lower amount of energy than conventional one, thus achieving higher COME yield

21 CFR 172.816 - Methyl glucoside-coconut oil ester.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methyl glucoside-coconut oil ester. 172.816 Section... HUMAN CONSUMPTION Multipurpose Additives § 172.816 Methyl glucoside-coconut oil ester. Methyl glucoside-coconut oil ester may be safely used in food in accordance with the following conditions: (a) It is the...

Catalytic Ester to Stannane Functional Group Interconversion via Decarbonylative Cross-Coupling of Methyl Esters

KAUST Repository

Yue, Huifeng

2018-01-03

An unprecedented conversion of methyl esters to stannanes was realized, providing access to a series of arylstannanes via nickel catalysis. Various common esters including ethyl, cyclohexyl, benzyl, and phenyl esters can undergo the newly developed decarbonylative stannylation reaction. The reaction shows broad substrate scope, can differentiate between different types of esters, and if applied in consecutive fashion, allows the transformation of methyl esters into aryl fluorides or biaryls via fluororination or arylation.

Catalytic Ester to Stannane Functional Group Interconversion via Decarbonylative Cross-Coupling of Methyl Esters

KAUST Repository

Yue, Huifeng; Zhu, Chen; Rueping, Magnus

2018-01-01

An unprecedented conversion of methyl esters to stannanes was realized, providing access to a series of arylstannanes via nickel catalysis. Various common esters including ethyl, cyclohexyl, benzyl, and phenyl esters can undergo the newly developed decarbonylative stannylation reaction. The reaction shows broad substrate scope, can differentiate between different types of esters, and if applied in consecutive fashion, allows the transformation of methyl esters into aryl fluorides or biaryls via fluororination or arylation.

Heterogeneous ozonation reactions of PAHs and fatty acid methyl esters in biodiesel particulate matter

Science.gov (United States)

Kasumba, John; Holmén, Britt A.

2018-02-01

Numerous studies have examined the oxidation of PAHs found in diesel particulate matter (PM) by ozone, but no studies have investigated the ozone oxidation of biodiesel exhaust PM. Fatty acid methyl esters (FAMEs), found in high abundance in biodiesel PM, can potentially alter the kinetics of the reactions between atmospheric oxidants such as ozone and particle-phase PAHs. In this study, the heterogeneous reactivity of 16 EPA PAHs upon 24 h exposure to 0.4 ppm ozone in the presence (PAH + FAMES) and absence (PAH-only) of FAMEs was investigated at room temperature and 50% relative humidity. The ozone-reactivity of the PAHs detected in 20% biodiesel (B20) exhaust PM was also investigated. In the absence of FAMEs, the pseudo-first order ozone reaction rate constant, kO 3 , of PAHs varied from 0.086 ± 0.030 hr-1 (chrysene) to 0.184 ± 0.078 hr-1 (anthracene). In the presence of FAMEs, kO 3 of the PAHs varied between 0.013 ± 0.012 hr-1 (benzo[b]fluoranthene) and 0.168 ± 0.028 hr-1 (benzo[a]pyrene), and with the exception of benzo[a]pyrene, the kO 3 of PAHs were 1.2-8 times lower compared to those obtained during the PAH-only ozone exposure. Only one PAH, benzo[a]pyrene (BaP), did not show a significant change in kO3 with addition of FAMEs. Phenanthrene, fluoranthene, and pyrene, the only PAHs detected in the B20 PM, had kO 3 values about 4 times lower in B20 PM than those obtained when spiked PAHs-only were exposed to ozone. The kO 3 values of phenanthrene and fluoranthene in the B20 PM were 2 times higher than rates obtained when the PAH mix was exposed to ozone in the presence of the FAMEs. In contrast, pyrene's kO 3 in the B20 PM was about 2 times lower than that obtained for the PAH + FAMEs exposure. Observed differences in PAH behavior demonstrate individual PAH heterogeneous reactivity with gas-phase ozone is sensitive to PAH (vapor pressure, solubility/sorption to matrix components, chemical reactivity) as well as substrate properties (PAH and O3 diffusivity

21 CFR 178.3600 - Methyl glucoside-coconut oil ester.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methyl glucoside-coconut oil ester. 178.3600... SANITIZERS Certain Adjuvants and Production Aids § 178.3600 Methyl glucoside-coconut oil ester. Methyl glucoside-coconut oil ester identified in § 172.816(a) of this chapter may be safely used as a processing...

Study on the spray characteristics of methyl esters from waste cooking oil at elevated temperature

Energy Technology Data Exchange (ETDEWEB)

Lin, Yung-Sung [Department of Mechanical and Automation Engineering, Da-Yeh University, 168 University Road, Dacun, Changhua 51591 (China); Department of Mechanical Engineering, Hsiuping Institute of Technology, No.11, Gongye Rd., Dali City, Taichung County 412-80 (China); Lin, Hai-Ping [Department of Mechanical and Automation Engineering, Da-Yeh University, 168 University Road, Dacun, Changhua 51591 (China)

2010-09-15

In Taiwan, millions of tons of waste cooking oil are produced each year, and less than 20% of it, about 150,000 ton/a, is reclaimed and reused. Most waste oil is flushed down the drain. Utilizing waste cooking oil to make biodiesel not only reduces engine exhaust gas pollution, but also replaces food-derived fuels, and reduces ecologic river pollution. This study employed two-stage transesterification to lower the high viscosity of waste oil, utilized emulsion to reduce the methyl ester NOx pollution, and used methanol to enhance the stability and viscosity of emulsified fuel. To further analyze spray characteristics of fuels, this experiment built a constant volume bomb under high temperature, used high speed photography to analyze spray tip penetration, spray angle, and the Sauter mean diameter (SMD) of fuel droplets, and compared the results with fossil diesel. The experimental results suggested that, two-stage transesterification can significantly lower waste oil viscosity to that which is close to fossil diesel viscosity. At a temperature above 300 C, waste cooking oil methyl esters had a water content of 20%, spray droplet characteristics were significantly improved, and NOx emission dropped significantly. The optimal fuel ratio suggested in this experiment was waste cooking oil methyl ester 74.5%, methanol 5%, water 20%, and composite surfactant Span-Tween 0.5%. (author)

Investigating 'Egusi' (citrullus colocynthis l.) seed oil as potential biodiesel feedstock

Energy Technology Data Exchange (ETDEWEB)

Giwa, S.; Adam, N. M. [Alternative and Renewable Energy Laboratory, Institute of Advanced Technology (ITMA)/Mechanical and Manufacturing Engineering Department, Faculty of Engineering, University Putra Malaysia, 43400, Serdang Darul Ehsan, Selangor (Malaysia); Abdullah, L. Ch. [Chemical and Environmental Engineering Department, Faculty of Engineering, University Putra Malaysia, 43400, Serdang Darul Ehsan, Selangor (Malaysia); Laboratory of Biopolymer and Derivatives, Institute of Tropical Forestry and Forest Products (INTROP), University Putra Malaysia, 43400, Serdang Darul Ehsan, Selangor (Malaysia)

2010-07-01

Biodiesel's acceptance as a substitute for fossil-derived diesel has grown the world over. However, the food-fuel debate over conventional vegetable oils has rekindled research interest in exploring lesser known and minor oil crops. In this work, egusi melon seed oil was studied for the first time as a potential feedstock for biodiesel production. Crude egusi melon seed oil was transesterified using sodium methoxide as the catalyst at 60 {sup o}C and an oil/methanol ratio of 1:6 to produce its corresponding methyl esters. Egusi melon oil methyl ester (EMOME) yield was 82%. Gas chromatographic analysis of EMOME showed that it was composed mainly of palmitic, stearic, oleic, linoleic and linolenic esters, which is similar to the profile of sunflower, soybean and safflower oil. All the measured fuel properties of EMOME satisfied both the ASTM D6751 and the EN 14214 biodiesel standards. Fuel properties of EMOME were essentially identical with those of soybean, safflower and sunflower biodiesel. Remarkably, the kinematic viscosity of EMOME was measured to be 3.83 mm{sup 2}/s, a value lower than most biodiesel fuels reported in the literature. The potential of egusi melon seed oil as a biodiesel feedstock is clearly presented in this study. (author)

Effect of antioxidants on the oxidative stability of methyl soyate (biodiesel)

Energy Technology Data Exchange (ETDEWEB)

Dunn, Robert O. [Food and Industrial Oils Research, USDA, Agricultural Research Service, National Center for Agricultural Utilization Research, 1815 N. University St., Peoria, IL 61604-3999 (United States)

2005-06-25

Biodiesel, an alternative diesel fuel derived from transesterification of vegetable oils or animal fats, is composed of saturated and unsaturated long-chain fatty acid alkyl esters. When exposed to air during storage, autoxidation of biodiesel can cause degradation of fuel quality by adversely affecting properties such as kinematic viscosity, acid value and peroxide value. One approach for increasing resistance of fatty derivatives against autoxidation is to treat them with oxidation inhibitors (antioxidants). This study examines the effectiveness of five such antioxidants, tert-butylhydroquinone (TBHQ), butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT), propyl gallate (PrG) and {alpha}-Tocopherol in mixtures with soybean oil fatty acid methyl esters (SME). Antioxidant activity in terms of increasing oxidation onset temperature (OT) was determined by non-isothermal pressurized-differential scanning calorimetry (P-DSC). Analyses were conducted in static (zero gas flow) and dynamic (positive gas flow) mode under 2000 kPa (290 psig) pressure and 5 {sup o}C/min heating scan rate. Results showed that PrG, BHT and BHA were most effective and {alpha}-Tocopherol least effective in increasing OT. Increasing antioxidant loading (concentration) showed sharp increases in activity for loadings up to 1000 ppm followed by smaller increases in activity at higher loadings. Phase equilibrium studies were also conducted to test physical compatibility of antioxidants in SME-No. 2 diesel fuel (D2) blends. Overall, this study recommends BHA or TBHQ (loadings up to 3000 ppm) for safeguarding biodiesel from effects of autoxidation during storage. BHT is also suitable at relatively low loadings (210 ppm after blending). PrG showed some compatibility problems and may not be readily soluble in blends with larger SME ratios. Although {alpha}-Tocopherol showed very good compatibility in blends, it was significantly less effective than the synthetic antioxidants screened in this

SINTESIS BIODIESEL DARI MINYAK LIMBAH BIJI KARET SEBAGAI SUMBER ENERGI ALTERNATIF (Synthesis of Biodiesel From Waste of Rubber Seed Oil as Alternative Energy Sources

Directory of Open Access Journals (Sweden)

Kasmadi Imam Supardi

2011-03-01

Full Text Available ABSTRAK Biji karet hanya ditemukan sebagai limbah padat dan belum termanfaatkan sepenuhnya. Minyak limbah biji karet yang digunakan dalam penelitian ini mengandung asam lemak bebas yang tinggi, yaitu 97,77% dan mempunyai bilangan asam yang tinggi pula yaitu setara dengan 6,2 mg KOH g minyak, sehingga perlu dilakukan esterifikasi untuk menurunkan kandungan asam lemak bebasnya menjadi ester. Metanol (20% volume minyak direaksikan dengan minyak limbah biji karet dengan katalis asam sulfat 98% (0,5% volume minyak menjadi ester. Dalam operasi reaksi transesterifikasi, digunakan variasi optimasi katalis yaitu pada 0,5% sampai 1,5% KOH dengan suhu operasi 60 o C dalam perbandingan metanol dengan minyak 1:3 (volume, dan dengan kecepatan pengadukan yang sama, didapatkan konsentrasi metil ester yang baik pada katalis 0,75%. Uji fisis minyak limbah biji karet hasil reaksi transesterifikasi adalah Specific Gravity 0,9000, Density 919,5, Korosi Lempeng Tembaga 1b, CCR 1,361% W, Kadar Air 0,22%, Viscosity 11,53mm 2 /s, dan Flash Point 182,5 o C. Hasil uji fisis menunjukkan belum semua parameter metil ester atau biodiesel memenuhi standar biodiesel. Hasil uji Performance unjuk kerja menunjukkan biodiesel yang dicampur solar dengan perbandingan volume 20:80 memberikan hasil emisi gas buang paling bersih dan waktu pembakaran yang paling lama. ABSTRACT Waste of rubber seeds is found only as a solid waste and has not fully exploited. Waste of rubber seed oil used in the research contains high free fatty acids, about 97.77% and higher acidity number, namely 6.2 mg KOH / g oil, so it needs esterification to reduce the free fatty acid content to be changed into ester. Methanol (20% volume of oil reacted with  waste of rubber seed oil to become methyl ester with sulfuric acid 98% (0,5% volume of oil as a catalyst. In the operations of transesterification variations of the optimization of catalyst 0.5% until 1.5% KOH was used with operating temperature of 60o C in

Cu2+ Montmorillonite K10 Clay Catalyst as a Green Catalyst for Production of Stearic Acid Methyl Ester: Optimization Using Response Surface Methodology (RSM)

OpenAIRE

Enas A. Almadani; Farah W. Harun; Salina M. Radzi; Syamsul K. Muhamad

2018-01-01

Clay catalyst has received much attention to replace the homogeneous catalysts in the esterification reaction to produce fatty acid methyl ester as the source of biodiesel as it is low cost, easily available, as well as environmental friendly. However, the use of unmodified clay, in particular montmorillonite K10 (MMT K10), for the esterification of fatty acids showed that the acid conversion was less than 60% and this is not preferable to the production of biodiesel. In this study, synthesis...

Continuous production of biodiesel under supercritical methyl acetate conditions: Experimental investigation and kinetic model.

Science.gov (United States)

Farobie, Obie; Matsumura, Yukihiko

2017-10-01

In this study, biodiesel production by using supercritical methyl acetate in a continuous flow reactor was investigated for the first time. The aim of this study was to elucidate the reaction kinetics of biodiesel production by using supercritical methyl. Experiments were conducted at various reaction temperatures (300-400°C), residence times (5-30min), oil-to-methyl acetate molar ratio of 1:40, and a fixed pressure of 20MPa. Reaction kinetics of biodiesel production with supercritical methyl acetate was determined. Finally, biodiesel yield obtained from this method was compared to that obtained with supercritical methanol, ethanol, and MTBE (methyl tertiary-butyl ether). The results showed that biodiesel yield with supercritical methyl acetate increased with temperature and time. The developed kinetic model was found to fit the experimental data well. The reactivity of supercritical methyl acetate was the lowest, followed by that of supercritical MTBE, ethanol, and methanol, under the same conditions. Copyright © 2017. Published by Elsevier Ltd.

Synthesis of methyl esters from waste cooking oil using construction waste material as solid base catalyst.

Science.gov (United States)

Balakrishnan, K; Olutoye, M A; Hameed, B H

2013-01-01

The current research investigates synthesis of methyl esters by transesterification of waste cooking oil in a heterogeneous system, using barium meliorated construction site waste marble as solid base catalyst. The pretreated catalyst was calcined at 830 °C for 4h prior to its activity test to obtained solid oxide characterized by scanning electron microscopy/energy dispersive spectroscopy, BET surface area and pore size measurement. It was found that the as prepared catalyst has large pores which contributed to its high activity in transesterification reaction. The methyl ester yield of 88% was obtained when the methanol/oil molar ratio was 9:1, reaction temperature at 65 °C, reaction time 3h and catalyst/oil mass ratio of 3.0 wt.%. The catalyst can be reused over three cycles, offer low operating conditions, reduce energy consumption and waste generation in the production of biodiesel. Copyright © 2012 Elsevier Ltd. All rights reserved.

Preparation of Jojoba Oil Ester Derivatives for Biodiesel Evaluation

Science.gov (United States)

As a result of the increase in commodity vegetable oil prices, it is imperative that non-food oils should be considered as alternative feedstocks for biodiesel production. Jojoba oil is unusual in that it is comprised of wax esters as opposed to the triglycerides found in typical vegetable oils. A...

Development and validation of a generic reduced chemical kinetic mechanism for CFD spray combustion modelling of biodiesel fuels

DEFF Research Database (Denmark)

Cheng, Xinwei; Ng, Hoon Kiat; Ho, Jee Hou

2015-01-01

In this reported work, a generic reduced biodiesel chemical kinetic mechanism, with components of methyl decanoate (C11H22O2, MD), methyl-9-decenoate (C11H20O2, MD9D) and n-heptane (C7H16) was built to represent the methyl esters of coconut, palm, rapeseed and soybean. The reduced biodiesel...... and detailed mechanism predictions, for each zero-dimensional (0D) auto-ignition and extinction process using CHEMKIN-PRO. Maximum percentage errors of less than 40.0% were recorded when the predicted ignition delay (ID) periods for coconut, palm, rapeseed and soybean methyl esters were compared to those...

Investigating “Egusi” (Citrullus Colocynthis L. Seed Oil as Potential Biodiesel Feedstock

Directory of Open Access Journals (Sweden)

Solomon Giwa

2010-03-01

Full Text Available Biodiesel’s acceptance as a substitute for fossil-derived diesel has grown the world over. However, the food-fuel debate over conventional vegetable oils has rekindled research interest in exploring lesser known and minor oil crops. In this work, egusi melon seed oil was studied for the first time as a potential feedstock for biodiesel production. Crude egusi melon seed oil was transesterified using sodium methoxide as the catalyst at 60 °C and an oil/methanol ratio of 1:6 to produce its corresponding methyl esters. Egusi melon oil methyl ester (EMOME yield was 82%. Gas chromatographic analysis of EMOME showed that it was composed mainly of palmitic, stearic, oleic, linoleic and linolenic esters, which is similar to the profile of sunflower, soybean and safflower oil. All the measured fuel properties of EMOME satisfied both the ASTM D6751 and the EN 14214 biodiesel standards. Fuel properties of EMOME were essentially identical with those of soybean, safflower and sunflower biodiesel. Remarkably, the kinematic viscosity of EMOME was measured to be 3.83 mm2/s, a value lower than most biodiesel fuels reported in the literature. The potential of egusi melon seed oil as a biodiesel feedstock is clearly presented in this study.

Jatropha oil methyl ester and its blends used as an alternative fuel in diesel engine

Directory of Open Access Journals (Sweden)

Yarrapathruni Rao Hanumantha Venkata

2009-01-01

Full Text Available Biomass derived vegetable oils are quite promising alternative fuels for agricultural diesel engines. Use of vegetable oils in diesel engines leads to slightly inferior performance and higher smoke emissions due to their high viscosity. The performance of vegetable oils can be improved by modifying them through the transesterification process. In this present work, the performance of single cylinder water-cooled diesel engine using methyl ester of jatropha oil as the fuel was evaluated for its performance and exhaust emissions. The fuel properties of biodiesel such as kinematic viscosity, calorific value, flash point, carbon residue, and specific gravity were found. Results indicate that B25 has closer performance to diesel and B100 has lower brake thermal efficiency mainly due to its high viscosity compared to diesel. The brake thermal efficiency for biodiesel and its blends was found to be slightly higher than that of diesel fuel at tested load conditions and there was no difference of efficiency between the biodiesel and its blended fuels. For jatropha biodiesel and its blended fuels, the exhaust gas temperature increased with the increase of power and amount of biodiesel. However, its diesel blends showed reasonable efficiency, lower smoke, and CO2 and CO emissions.

Palm oil biodiesel synthesized with potassium loaded calcined hydrotalcite and effect of biodiesel blend on elastomer properties

Energy Technology Data Exchange (ETDEWEB)

Trakarnpruk, Wimonrat; Porntangjitlikit, Suriya [Petrochemistry and Polymer Science, Department of Chemistry, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand)

2008-07-15

Biodiesel was prepared from palm oil by transesterification with methanol in the presence of 1.5%K loaded-calcined Mg-Al hydrotalcite. Fatty acid methyl esters content of 96.9% and methyl ester yield of 86.6% were achieved using a 30:1 methanol to oil molar ratio at 100{sup o}C for 6 h and 7 wt% catalyst. The biodiesel was characterized and its impact on elastomer properties was evaluated. The compatibility of B10 diesel blend (10% biodiesel) with six types of elastomers commonly found in fuel systems (NBR, HNBR, NBR/PVC, acrylic rubber, co-polymer FKM, and terpolymer FKM) were investigated. The physical properties of elastomers after immersion in tested fuels (for 22, 670, and 1008 h at 100{sup o}C) were measured according to American Society of Testing and Materials (ASTM). These include swelling (mass change and volume change), hardness, tensile and elongation, as well as the dynamic mechanical property. The results showed that properties of NBR, NBR/PVC and acrylic rubber were affected more than other elastomers. This is due to the absorption and dissolving of biodiesel by rubber in these samples. Co-polymer FKM and terpolymer FKM which are fluoroelastomers show little property change. (author)

Effect of temperature stress on protein methyl esters

International Nuclear Information System (INIS)

Welch, W.; Kracaw, K.

1986-01-01

Protein methyl esters have been implicated in a number of physiological processes. They have measured the effect of temperature stress on the levels of protein methyl esters in the mesophilic fungus Penicillium chrysogenum (PCPS) and the thermophilic fungus P. duponti (PD). PD and PCPS were incubated with [methyl- 3 H]methionine. The mycelia were collected by filtration, frozen in liquid nitrogen and ground to a fine powder. The nitrogen powder was extracted with either phosphate buffer or with SDS, glycerol, phosphate, 2-mercaptoethanol. Insoluble material was removed by centrifugation. The supernatants were assayed for protein methyl esters. The released [ 3 H]methanol was extracted into toluene:isoamyl alcohol (3:2) and quantitated by liquid scintillation. The production of volatile methanol was confirmed by use of Conway diffusion cells. Soluble proteins accounted for about one-fourth of the total protein methyl ester extracted by SDS. In PCPS, the SDS extracted proteins have about three times the level of esterification of the soluble proteins whereas in PD there is little difference between soluble and SDS extracted protein. The level of protein esterification in PD is about one-tenth that observed in PCPS. Temperature stress caused large changes in the level of protein esterification. The data suggest protein methyl esters may contribute to the adaptation to environmental stress

Oxidation stability and risk evaluation of biodiesel

Directory of Open Access Journals (Sweden)

Hoshino Takashi

2007-01-01

Full Text Available This review describes oxidation and thermal stability and hazardous possibility of biodiesel by auto-oxidation. As it can be distributed using today’s infrastructure biodisel production has increased especially in the European Union. Biodiesel has many surpassing properties as an automotive fuel. Biodiesel is considered safer than diesel fuel because of the high flash point, but it has oxygen and double bond(s. Fatty acid methyl esters are more sensitive to oxidative degradation than fossil diesel fuel. The ability of producing peroxides is rather high, therefore we should care of handling of biodiesel.

Natural and synthetic antioxidants: Influence on the oxidative stability of biodiesel synthesized from non-edible oil

Energy Technology Data Exchange (ETDEWEB)

Sarin, Amit [Department of Applied Sciences, Amritsar College of Engineering and Technology, Manawala, Amritsar-143001, Punjab (India); Singh, N.P. [Punjab Technical University, Jalandhar (India); Sarin, Rakesh; Malhotra, R.K. [Indian Oil Corporation Ltd., R and D Centre, Sector-13, Faridabad-121007 (India)

2010-12-15

According to the proposed National Mission on Biodiesel in India, we have undertaken studies on the oxidative stability of biodiesel synthesized from tree borne non-edible oil seeds jatropha. Neat jatropha biodiesel exhibited oxidation stability of 3.95 h and research was conducted to investigate the influence of natural and synthetic antioxidants on the oxidation stability of jatropha methyl ester. Antioxidants namely {alpha}-tocopherol, tert-butylated hydroxytoluene, tert-butylated phenol derivative, octylated butylated diphenyl amine, and tert-butylhydroxquinone were doped to improve the oxidation stability. It was found that both types of antioxidants showed beneficial effects in increasing the oxidation stability of jatropha methyl ester, but comparatively, the synthetic antioxidants were found to be more effective. (author)

Optimization of sunflower oil methanolysis for the production of biodiesel and its characterization with spectroscopic techniques (abstract)

International Nuclear Information System (INIS)

Tariq, M.; Ali, S.; Khalid, N.; Naureen, R.; Rafique, U.

2011-01-01

Esters from vegetable oils have attracted a great deal of interest as substitute for petrodiesel to reduce dependence on imported petroleum and provide an alternate and sustainable source for fuel with more benign environmental properties. In the present study biodiesel was prepared from sunflower seed oil by transesterification by alkali-catalyzed methanolysis. The fuel properties like kinematic viscosity, density, specific gravity, flash point, pour point, cloud point, acid number and colour comparison of sunflower oil biodiesel (SOB) were determined and discussed in the light of ASTM D6751 standards for biodiesel. The SOB was chemically characterized with analytical techniques like FT-IR, NMR (/sup 1/H and /sup 13/C). The chemical composition of SOB was determined by GC-MS. Various fatty acid methyl esters (FAMEs) were identified by retention time data and verified by mass fragmentation patterns. The identified FAMEs were methyl dodecanoate (C/sub 12:0/), methyl tetradecanoate(C/sub 14:0/), methyl hexadecanoate (C/sub 16:0/), methyl 8,11-octadecadienoate (C/sub 18:2/), methyl 9-octadecenoate (C/sub 18:1/), methyl octadecanoate (C/sub 18:0/), methyl 11-eicosenoate (C/sub 20:1/), methyl eicosanoate (C/sub 20:0/), methyl 13-docosenoate(C/sub 22:1/), methyl docosenoate(C/sub 22:0/) and methyl tetracosanoate (C/sub 24:0/). The percentage conversion of triglycerides to corresponding methyl esters determined by /sup 1/H-NMR was 87.33 % which was quite in good agreement with the practically observed yield of 85.1 %. (author)

Extraction of extracellular lipids from chemoautotrophic bacteria Serratia sp. ISTD04 for production of biodiesel.

Science.gov (United States)

Bharti, Randhir K; Srivastava, Shaili; Thakur, Indu Shekhar

2014-08-01

A CO2 sequestering bacterial strain, Serratia sp. ISTD04, that produces a significant amount of extracellular lipids was isolated from marble mine rocks. (14)C labeling analysis revealed that the rate of assimilation of CO2 by the strain is 0.756×10(-9)μmolCO2fixedcell(-1)h(-1). It was found to produce 466mg/l of extracellular lipid which was characterized using (1)H NMR. After transesterification of lipids, the total saturated and unsaturated FAME was found to be 51% and 49% respectively. The major FAME contained in the biodiesel were palmitic acid methyl ester (C16:0), oleic acid methyl ester (C18:1) and 10-nonadecenoic acid methyl ester (C19:1). Biodiesel produced by Serratia sp. ISTD04 is balanced in terms of FAME composition of good quality. It also contained higher proportion of oleic acid (35%) which makes it suitable for utilization in existing engines. Thus, the strain can be harnessed commercially to sequester CO2 into biodiesel. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of steam injection on nox emissions and performance of a single cylinder diesel engine fuelled with soy methyl ester

Directory of Open Access Journals (Sweden)

Manickam Madhavan V.

2017-01-01

Full Text Available Biodiesel attracts most of the researchers and automotive industries in recent years as an alternative fuel for diesel engines, because of its better lubricity property, higher cetane number, and less greenhouse gas emissions. The use of bio diesel leads to reduction in hydro carbons, carbon monoxide, and particulate matter, but increase in NOx emissions. Increase in biodiesel blends in standard diesel leads to increase in NOx emission. In this study, an attempt is made to reduce the NOx emis-sions of a diesel engine fueled with pure soy methyl ester (B100 with low pressure steam injection. Experiments were carried out and studied for both standard diesel and pure biodiesel of soy methyl ester with steam injection ratio of 5, 10, and 15% on mass ratio basis of air in the inlet manifold. The present study has shown that around 30% reduction in NOx can be achieved for the steam injection rate of 10% and considerable reduction for all other steam injection rates when compared to standard diesel and B100. It is also observed that steam injection having signifi-cant impact on reduction of other emissions such as HC, CO, and CO2. The study also noted marginal improvement in the engine brake power, brake thermal effi-ciency and reduction in specific fuel consumption at part loads and minor increase during peak load operation for the low pressure steam injection on B100.

Co-solvents transesterification of cotton seed oil into biodiesel: Effects of reaction conditions on quality of fatty acids methyl esters

International Nuclear Information System (INIS)

Alhassan, Y.; Kumar, N.; Bugaje, I.M.; Pali, H.S.; Kathkar, P.

2014-01-01

Highlights: • Using co-solvent systems reduce reaction time by 60%. • Only small volume of co-solvent is required to improve the process. • Greater than 90% yields were obtained within the first 10 min. • Physico-chemical and fuel properties of FAMEs were within standard limits. • Acetone was found to be the best co-solvent for the transesterification. - Abstract: Solvent Technology, is gaining the interest of researchers in improving transesterification process recently. Transesterification of cotton seed oil into biodiesel using different mixtures of methanol with Diethyl Ether (DEE), Dichlorobenzene (CBN) or Acetone (ACT) co-solvent systems was conducted. Potassium hydroxide (KOH) was used as the catalyst all through. The reaction conditions optimized include; the molar ratio of co-solvent in methanol, reaction temperature and time. The catalyst concentration was also optimized. The optimization was based on the percentage yields of Fatty Acids Methyl Esters (FAMEs) produced. In addition, the effects of co-solvent systems on physico-chemical properties (Acid value and fatty acids composition) and fuel properties (viscosity, density and calorific value) were investigated as well. The result obtained, indicated 10% (v/v) addition of co-solvents CBN and ACT in methanol was the optimal volume. The optimal reaction temperature was 55 ° 0 C for 10 min when the catalyst concentration of 0.75% (w/w) weight of oil was used. Fuel properties were within the acceptable limit of ASTM and not significantly affected by the co-solvent systems except for the calorific value. It was concluded that the addition of co-solvent reduced the reaction time and improved some fuel properties of the biodiesel produced

Comparative Numerical Study of Four Biodiesel Surrogates for Application on Diesel 0D Phenomenological Modeling

Directory of Open Access Journals (Sweden)

Claude Valery Ngayihi Abbe

2016-01-01

Full Text Available To meet more stringent norms and standards concerning engine performances and emissions, engine manufacturers need to develop new technologies enhancing the nonpolluting properties of the fuels. In that sense, the testing and development of alternative fuels such as biodiesel are of great importance. Fuel testing is nowadays a matter of experimental and numerical work. Researches on diesel engine’s fuel involve the use of surrogates, for which the combustion mechanisms are well known and relatively similar to the investigated fuel. Biodiesel, due to its complex molecular configuration, is still the subject of numerous investigations in that area. This study presents the comparison of four biodiesel surrogates, methyl-butanoate, ethyl-butyrate, methyl-decanoate, and methyl-9-decenoate, in a 0D phenomenological combustion model. They were investigated for in-cylinder pressure, thermal efficiency, and NOx emissions. Experiments were performed on a six-cylinder turbocharged DI diesel engine fuelled by methyl ester (MEB and ethyl ester (EEB biodiesel from wasted frying oil. Results showed that, among the four surrogates, methyl butanoate presented better results for all the studied parameters. In-cylinder pressure and thermal efficiency were predicted with good accuracy by the four surrogates. NOx emissions were well predicted for methyl butanoate but for the other three gave approximation errors over 50%.

Relationship between fatty acid composition and biodiesel quality for nine commercial palm oils

Directory of Open Access Journals (Sweden)

Chanida Lamaisri

2015-08-01

Full Text Available Biodiesel is an alternative fuel consisting of alkyl esters of fatty acids from vegetable oils or animal fats. The fatty acid compositions in the oils used as feedstock can influence quality of the biodiesel. In the present study, oil content and fatty acid composition of mesocarp and kernel oil were examined from nine commercial oil palm Elaeis guineensis cultivars. Saponification number, iodine value and cetane number were calculated from palm oil fatty acid methyl ester compositions. Fruits of tenera oil palm were collected from a farmer’s plantation in Dan Makham Tia District, Kanchanaburi Province in 2009. Variation between cultivars was observed in oil content and fatty acid profile of mesocarp oil rather than kernel oil. The percentage of oil in dry mesocarp ranged from 63.8% to 74.9%. The mesocarp oil composed of 41.5 - 51.6% palmitic acid, 3.58-7.10% stearic acid, 32.8-42.5% oleic acid and 9.3-13.0% linoleic acid. Likewise saponification number, iodine value and cetane number of mesocarp oil fatty acid methyl ester showed more variation among cultivars, ranging from 196.5-198.9, 45.7-54.6 and 61.8-63.6, respectively. While those of kernel oil fatty acid methyl ester showed no different among cultivars, ranging from 229-242, 13.6-16.4 and 65.3-66.5, respectively. The cetane number of fatty acid methyl ester positively correlated with contents of myristic, palmitic and stearic acids in palm oil and saponification number of biodiesel, but negatively correlated with iodine value

High free fatty acid coconut oil as a potential feedstock for biodiesel production in Thailand

Energy Technology Data Exchange (ETDEWEB)

Nakpong, Piyanuch; Wootthikanokkhan, Sasiwimol [Department of Chemistry, Faculty of Science and Technology, Rajamangala University of Technology Krungthep, 2 Nanglinchee Road, Sathorn, Bangkok 10120 (Thailand)

2010-08-15

Coconut oil having 12.8% free fatty acid (FFA) was used as a feedstock to produce biodiesel by a two-step process. In the first step, FFA level of the coconut oil was reduced to 0.6% by acid-catalyzed esterification. In the second step, triglycerides in product from the first step were transesterified with methanol by using an alkaline catalyst to produce methyl esters and glycerol. Effect of parameters related to these processes was studied and optimized, including methanol-to-oil ratio, catalyst concentration, reaction temperature, and reaction time. Methyl ester content of the coconut biodiesel was determined by GC to be 98.4% under the optimum condition. The viscosity of coconut biodiesel product was very close to that of Thai petroleum diesel and other measured properties met the Thai biodiesel (B100) specification. (author)

Evaluation of biodiesel obtained from cottonseed oil

Energy Technology Data Exchange (ETDEWEB)

Rashid, Umer [Department of Chemistry and Biochemistry, University of Agriculture, Faisalabad-38040 (Pakistan); Department of Industrial Chemistry, Government College University, Faisalabad-38000 (Pakistan); Anwar, Farooq [Department of Chemistry and Biochemistry, University of Agriculture, Faisalabad-38040 (Pakistan); Knothe, Gerhard [United States Department of Agriculture, Agricultural Research Service, National Center for Agricultural Utilization Research, Peoria, IL 61604 (United States)

2009-09-15

Esters from vegetable oils have attracted a great deal of interest as substitutes for petrodiesel to reduce dependence on imported petroleum and provide a fuel with more benign environmental properties. In this work biodiesel was prepared from cottonseed oil by transesterification with methanol, using sodium hydroxide, potassium hydroxide, sodium methoxide and potassium methoxide as catalysts. A series of experiments were conducted in order to evaluate the effects of reaction variables such as methanol/oil molar ratio (3:1-15:1), catalyst concentration (0.25-1.50%), temperature (25-65 C), and stirring intensity (180-600 rpm) to achieve the maximum yield and quality. The optimized variables of 6:1 methanol/oil molar ratio (mol/mol), 0.75% sodium methoxide concentration (wt.%), 65 C reaction temperature, 600 rpm agitation speed and 90 min reaction time offered the maximum methyl ester yield (96.9%). The obtained fatty acid methyl esters (FAME) were analyzed by gas chromatography (GC) and {sup 1}H NMR spectroscopy. The fuel properties of cottonseed oil methyl esters (COME), cetane number, kinematic viscosity, oxidative stability, lubricity, cloud point, pour point, cold filter plugging point, flash point, ash content, sulfur content, acid value, copper strip corrosion value, density, higher heating value, methanol content, free and bound glycerol were determined and are discussed in the light of biodiesel standards such as ASTM D6751 and EN 14214. (author)

21 CFR 573.640 - Methyl esters of higher fatty acids.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Methyl esters of higher fatty acids. 573.640... ANIMALS Food Additive Listing § 573.640 Methyl esters of higher fatty acids. The food additive methyl esters of higher fatty acids may be safely used in animal feeds in accordance with the following...

Chemical Kinetic Influences of Alkyl Chain Structure on the High Pressure and Temperature Oxidation of a Representative Unsaturated Biodiesel: Methyl Nonenoate.

Science.gov (United States)

Fridlyand, Aleksandr; Goldsborough, S Scott; Brezinsky, Kenneth

2015-07-16

The high pressure and temperature oxidation of methyl trans-2-nonenoate, methyl trans-3-nonenoate, 1-octene, and trans-2-octene are investigated experimentally to probe the influence of the double bond position on the chemical kinetics of long esters and alkenes. Single pulse shock tube experiments are performed in the ranges p = 3.8-6.2 MPa and T = 850-1500 K, with an average reaction time of 2 ms. Gas chromatographic measurements indicate increased reactivity for trans-2-octene compared to 1-octene, whereas both methyl nonenoate isomers have reactivities similar to that of 1-octene. A difference in the yield of stable intermediates is observed for the octenes when compared to the methyl nonenoates. Chemical kinetic models are developed with the aid of the Reaction Mechanism Generator to interpret the experimental results. The models are created using two different base chemistry submodels to investigate the influence of the foundational chemistry (i.e., C0-C4), whereas Monte Carlo simulations are performed to examine the quality of agreement with the experimental results. Significant uncertainties are found in the chemistry of unsaturated esters with the double bonds located close to the ester groups. This work highlights the importance of the foundational chemistry in predictive chemical kinetics of biodiesel combustion at engine relevant conditions.

Techno-economic analysis of biodiesel production from Jatropha curcas via a supercritical methanol process

International Nuclear Information System (INIS)

Yusuf, N.N.A.N.; Kamarudin, S.K.

2013-01-01

Highlights: • This paper presents the techno-economic of a production of biodiesel from JCO. • The results obtained 99.96% of biodiesel with 96.49% of pure glycerol. • This proved that biodiesel from JCO is the least expensive compare to other resources. - Abstract: This paper presents the conceptual design and economic evaluation of a production of methyl esters (biodiesel) from Jatropha curcas oil (JCO) via a supercritical methanol process with glycerol as a by-product. The process consists of four major units: transesterification (PFR), methanol recovery (FT) and (DC1), recovery of glycerol (DEC), and biodiesel purification (DC2). The material and heat balance are also presented here. A biodiesel production of 40,000 tonnes-yr −1 is taken as case study. Biodiesel obtained from supercritical transesterification with Jatropha curcas oil as feedstock resulting in high purity methyl esters (99.96%) with almost pure glycerol (96.49%) obtained as by-product. The biodiesel can be sold at USD 0.78 kg −1 , while the manufacturing and capital investment costs are in the range of USD 25.39 million-year −1 and USD 9.41 million year −1 , respectively. This study proved that biodiesel from JCO is the least expensive with purities comparable to those found in other studies

Oxidative stability and ignition quality of algae derived methyl esters containing varying levels of methyl eicosapentaenoate and methyl docosahexaenoate

Science.gov (United States)

Bucy, Harrison

Microalgae is currently receiving strong consideration as a potential biofuel feedstock to help meet the advanced biofuels mandate of the 2007 Energy Independence and Security Act because of its theoretically high yield (gallons/acre/year) in comparison to current terrestrial feedstocks. Additionally, microalgae also do not compete with food and can be cultivated with wastewater on non-arable land. Microalgae lipids can be converted into a variety of biofuels including fatty acid methyl esters (e.g. FAME biodiesel), renewable diesel, renewable gasoline, or jet fuel. For microalgae derived FAME, the fuel properties will be directly related to the fatty acid composition of the lipids produced by the given microalgae strain. Several microalgae species under consideration for wide scale cultivation, such as Nannochloropsis, produce lipids with fatty acid compositions containing substantially higher quantities of long chainpolyunsaturated fatty acids (LC-PUFA) in comparison to terrestrial feedstocks. It is expected that increased levels of LC-PUFA will be problematic in terms of meeting all of the current ASTM specifications for biodiesel. For example, it is known that oxidative stability and cetane number decrease with increasing levels of LC-PUFA. However, these same LC-PUFA fatty acids, such as eicosapentaenoic acid (EPA: C20:5) and docosahexaenoic acid (DHA: C22:6) are known to have high nutritional value thereby making separation of these compounds economically attractive. Given the uncertainty in the future value of these LC-PUFA compounds and the economic viability of the separation process, the goal of this study was to examine the oxidative stability and ignition quality of algae-based FAME with varying levels of EPA and DHA removal. Oxidative stability tests were conducted at a temperature of 110°C and airflow of 10 L/h using a Metrohm 743 Rancimat with automatic induction period determination following the EN 14112 Method from the ASTM D6751 and EN 14214

21 CFR 573.660 - Methyl glucoside-coconut oil ester.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Methyl glucoside-coconut oil ester. 573.660 Section 573.660 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... ANIMALS Food Additive Listing § 573.660 Methyl glucoside-coconut oil ester. Methyl glucoside-coconut oil...

Light vehicle regulated and unregulated emissions from different biodiesels

International Nuclear Information System (INIS)

Karavalakis, George; Stournas, Stamoulis; Bakeas, Evangelos

2009-01-01

In this study, the regulated and unregulated emissions profile and fuel consumption of an automotive diesel and biodiesel blends, prepared from two different biodiesels, were investigated. The biodiesels were a rapeseed methyl ester (RME) and a palm-based methyl ester (PME). The tests were performed on a chassis dynamometer with constant volume sampling (CVS) over the New European Driving Cycle (NEDC) and the non-legislated Athens Driving Cycle (ADC), using a Euro 2 compliant passenger vehicle. The objectives were to evaluate the impact of biodiesel chemical structure on the emissions, as well as the influence of the applied driving cycle on the formation of exhaust emissions and fuel consumption. The results showed that NOx emissions were influenced by certain biodiesel properties, such as those of cetane number and iodine number. NOx emissions followed a decreasing trend over both cycles, where the most beneficial reduction was obtained with the application of the more saturated biodiesel. PM emissions were decreased with the palm-based biodiesel blends over both cycles, with the exception of the 20% blend which was higher compared to diesel fuel. PME blends led to increases in PM emissions over the ADC. The majority of the biodiesel blends showed a tendency for lower CO and HC emissions. The differences in CO2 emissions were not statistically significant. Fuel consumption presented an increase with both biodiesels. Total PAH and nitro-PAH emission levels were decreased with the use of biodiesel independently of the source material. Lower molecular weight PAHs were predominant in both gaseous and particulate phases. Both biodiesels had a negative impact on certain carbonyl emissions. Formaldehyde and acetaldehyde were the dominant aldehydes emitted from both fuels.

Spectroscopic studies of the quality of WCO (Waste Cooking Oil fatty acid methyl esters

Directory of Open Access Journals (Sweden)

Matwijczuk Arkadiusz

2018-01-01

Full Text Available Different kinds of biodiesel fuels become more and more attractive form of fuel due to their unique characteristics such as: biodegradability, replenishability, and what is more a very low level of toxicity in terms of using them as a fuel. The test on the quality of diesel fuel is becoming a very important issue mainly due to the fact that its high quality may play an important role in the process of commercialization and admitting it on the market. The most popular techniques among the wellknown are: molecular spectroscopy and molecular chromatography (especially the spectroscopy of the electron absorption and primarily the infrared spectroscopy (FTIR.The issue presents a part of the results obtained with the use of spectroscopy of the electron absorption and in majority infrared spectroscopy FTIR selected for testing samples of the acid fats WCO (Waste Cooking Oil types. The samples were obtained using laboratory methods from sunflower oil and additionally from waste animal fats delivered from slaughterhouses. Acid methyl esters were selected as references to present the samples. In order to facilitate the spectroscopic analysis, free glycerol, methanol, esters and methyl linolenic acid were measured

One-pot process combining transesterification and selective hydrogenation for biodiesel production from starting material of high degree of unsaturation.

Science.gov (United States)

Yang, Ru; Su, Mengxing; Li, Min; Zhang, Jianchun; Hao, Xinmin; Zhang, Hua

2010-08-01

A one-pot process combining transesterification and selective hydrogenation was established to produce biodiesel from hemp (Cannabis sativa L.) seed oil which is eliminated as a potential feedstock by a specification of iodine value (IV; 120 g I(2)/100g maximum) contained in EN 14214. A series of alkaline earth metal oxides and alkaline earth metal supported copper oxide were prepared and tested as catalysts. SrO supported 10 wt.% CuO showed the superior catalytic activity for transesterification with a biodiesel yield of 96% and hydrogenation with a reduced iodine value of 113 and also exhibited a promising selectivity for eliminating methyl linolenate and increasing methyl oleate without rising methyl stearate in the selective hydrogenation. The fuel properties of the selective hydrogenated methyl esters are within biodiesel specifications. Furthermore, cetane numbers and iodine values were well correlated with the compositions of the hydrogenated methyl esters according to degrees of unsaturation. (c) 2010 Elsevier Ltd. All rights reserved.

Theoretical modeling of iodine value and saponification value of biodiesel fuels from their fatty acid composition

Energy Technology Data Exchange (ETDEWEB)

Gopinath, A.; Puhan, Sukumar; Nagarajan, G. [Internal Combustion Engineering Division, Department of Mechanical Engineering, Anna University, Chennai 600 025, Tamil Nadu (India)

2009-07-15

Biodiesel is an alternative fuel consisting of alkyl esters of fatty acids from vegetable oils or animal fats. The properties of biodiesel depend on the type of vegetable oil used for the transesterification process. The objective of the present work is to theoretically predict the iodine value and the saponification value of different biodiesels from their fatty acid methyl ester composition. The fatty acid ester compositions and the above values of different biodiesels were taken from the available published data. A multiple linear regression model was developed to predict the iodine value and saponification value of different biodiesels. The predicted results showed that the prediction errors were less than 3.4% compared to the available published data. The predicted values were also verified by substituting in the available published model which was developed to predict the higher heating values of biodiesel fuels from their iodine value and the saponification value. The resulting heating values of biodiesels were then compared with the published heating values and reported. (author)

Esterification of oil adsorbed on palm decanter cake into methyl ester using sulfonated rice husk ash as heterogeneous acid catalyst

Science.gov (United States)

Hindryawati, Noor; Erwin, Maniam, Gaanty Pragas

2017-02-01

Palm Decanter cake (PDC) which is categorized as the waste from palm oil mill has been found to contain residual crude palm oil. The oil adsorbed on the PDC (PDC-oil) can be extracted and potentially used as feedstock for biodiesel production. Feedstock from waste like PDC-oil is burdened with high free fatty acids (FFAs) which make the feedstock difficult to be converted into biodiesel using basic catalyst. Therefore, in this study, a solid acid, RHA-SO3H catalyst was synthesized by sulfonating rice husk ash (RHA) with concentrated sulfuric acid. The RHA-SO3H prepared was characterized with TGA, FTIR, BET, XRD, FE-SEM, and Hammett indicators (methyl red, bromophenol blue, and crystal violet). PDC was found to have about 11.3 wt. % oil recovered after 1 hour extraction using ultrasound method. The presence of sulfonate group was observed in IR spectrum, and the surface area of RHA-SO3H was reduced to 37 m2.g-1 after impregnation of sulfonate group. The RHA-SO3H catalyst showed that it can work for both esterification of free fatty acid which is present in PDC-oil, and transesterification of triglycerides into methyl ester. The results showed highest methyl ester content of 70.2 wt.% at optimal conditions, which was 6 wt.% catalyst amount, methanol to oil molar ratio of 17:1 for 5 hours at 120 °C.

INFLUENCE OF PALM METHYL ESTER (PME AS AN ALTERNATIVE FUEL IN MULTICYLINDER DIESEL ENGINE

Directory of Open Access Journals (Sweden)

Mohd Hafizil M. Yasin

2012-12-01

Full Text Available Palm oil is one of the vegetable oil, which is converted to biodiesel through a transesterification process using methanol as the catalyst. Palm oil biodiesel or palm methyl ester (PME can be used in diesel engines without any modification, and can be blended with conventional diesel to produce different proportions of PME-diesel blend fuels. The physical properties of PME were evaluated experimentally and theoretically. The effect of using neat PME as fuel on engine performance and emissions was evaluated using a commercial four-cylinder four-stroke IDI diesel engine. The experimental results on an engine operated with PME exhibited higher brake specific fuel consumption in comparison with the conventional fuel. With respect to the in-cylinder pressure and heat release rate, these increased features by over 8.11% and 9.3% with PME compared to conventional diesel. The overall results show that PME surpassed the diesel combustion quality due to its psychochemical properties and higher oxygen content.

Biodiesel Production from Chlorella protothecoides Oil by Microwave-Assisted Transesterification.

Science.gov (United States)

Gülyurt, Mustafa Ömer; Özçimen, Didem; İnan, Benan

2016-04-22

In this study, biodiesel production from microalgal oil by microwave-assisted transesterification was carried out to investigate its efficiency. Transesterification reactions were performed by using Chlorella protothecoides oil as feedstock, methanol, and potassium hydroxide as the catalyst. Methanol:oil ratio, reaction time and catalyst:oil ratio were investigated as process parameters affected methyl ester yield. 9:1 methanol/oil molar ratio, 1.5% KOH catalyst/oil ratio and 10 min were optimum values for the highest fatty acid methyl ester yield.

Preparation of Biodiesel of Undi seed with In-situ Transesterification

Directory of Open Access Journals (Sweden)

Sanjaykumar DALVI

2012-08-01

Full Text Available The biodiesel fraction from oil content of Undi (Calophyllum innophyllum L. is found 60-70%. The extraction of oil is a primary step in any biodiesel production system. To escape this step in-situ transesterification method is used in which the Undi seed crush is directly converted into biodiesel with in-situ transesterification which is fatty acid methyl and ethyl ester composition. The single step reaction is eco-friendly as hexane like solvents not have been used for oil extraction. These components of biodiesel were analysed by GC-MS technique.

Experimental vapor pressures (from 1 Pa to 100 kPa) of six saturated Fatty Acid Methyl Esters (FAMEs): Methyl hexanoate, methyl octanoate, methyl decanoate, methyl dodecanoate, methyl tetradecanoate and methyl hexadecanoate

International Nuclear Information System (INIS)

Sahraoui, Lakhdar; Khimeche, Kamel; Dahmani, Abdallah; Mokbel, Ilham; Jose, Jacques

2016-01-01

Highlight: • Vapor-liquid equilibria, Enthalpy of Vaporization, saturated Fatty Acid Methyl Ester. - Abstract: Vapor pressures of six saturated Fatty Acid Methyl Esters (FAMEs), methyl hexanoate (or methyl caproate), methyl octanoate (or methyl caprylate), Methyl decanoate (or methyl caprate), methyl dodecanoate (or methyl laurate), methyl tetradecanoate (or methyl myristate), and methyl hexadecanoate (or methyl palmitate) were measured from 1 Pa to 100 kPa and at temperature range between 262 and 453 K using a static apparatus. The experimental data (P-T) were compared with the available literature data.

Base catalyzed transesterification of acid treated vegetable oil blend for biodiesel production

Energy Technology Data Exchange (ETDEWEB)

Yusup, Suzana; Khan, Modhar Ali [Chemical Engineering Department, Universiti Teknologi PETRONAS, Seri Iskandar, Tronoh, Perak 31750 (Malaysia)

2010-10-15

Biodiesel can be produced from low cost non-edible oils and fats. However, most of these sources are of high free fatty acid content which requires two stage transesterification to reduce the acid value and produce biodiesel. The acid treatment step is usually followed by base transesterification since the latter can yield higher conversions of methyl esters at shorter reaction time when compared with acid catalyzed reaction. In the current study, base transesterification in the second stage of biodiesel synthesis is studied for a blend of crude palm/crude rubber seed oil that had been characterized and treated with acid esterification. Optimum conditions for the reaction were established and effect of each variable was investigated. The base catalyzed transesterification favored a temperature of 55 C with methanol/oil molar ratio of 8/1 and potassium hydroxide at 2% (ww{sup -1}) (oil basis). The conversion of methyl esters exceeded 98% after 5 h and the product quality was verified to match that for biodiesel with international standards. (author)

Biodiesel production from microalgal isolates of southern Pakistan and quantification of FAMEs by GC-MS/MS analysis

Directory of Open Access Journals (Sweden)

Musharraf Syed

2012-12-01

Full Text Available Abstract Background Microalgae have attracted major interest as a sustainable source for biodiesel production on commercial scale. This paper describes the screening of six microalgal species, Scenedesmus quadricauda, Scenedesmus acuminatus, Nannochloropsis sp., Anabaena sp., Chlorella sp. and Oscillatoria sp., isolated from fresh and marine water resources of southern Pakistan for biodiesel production and the GC-MS/MS analysis of their fatty acid methyl esters (FAMEs. Results Growth rate, biomass productivity and oil content of each algal species have been investigated under autotrophic condition. Biodiesel was produced from algal oil by acid catalyzed transesterification reaction and resulting fatty acid methyl esters (FAMEs content was analyzed by GC/MS. Fatty acid profiling of the biodiesel, obtained from various microalgal oils showed high content of C-16:0, C-18:0, cis-Δ9C-18:1, cis-Δ11C-18:1 (except Scenedesmus quadricauda and 10-hydroxyoctadecanoic (except Scenedesmus acuminatus. Absolute amount of C-14:0, C-16:0 and C-18:0 by a validated GC-MS/MS method were found to be 1.5-1.7, 15.0-42.5 and 4.2-18.4 mg/g, respectively, in biodiesel obtained from various microalgal oils. Biodiesel was also characterized in terms of cetane number, kinematic viscosity, density and higher heating value and compared with the standard values. Conclusion Six microalgae of local origin were screened for biodiesel production. A method for absolute quantification of three important saturated fatty acid methyl esters (C-14, C-16 and C-18 by gas chromatography-tandem mass spectrometry (GC-MS/MS, using multiple reactions monitoring (MRM mode, was employed for the identification and quantification of biodiesels obtained from various microalgal oils. The results suggested that locally found microalgae can be sustainably harvested for the production of biodiesel. This offers the tremendous economic opportunity for an energy-deficient nation.

Impacts of biodiesel production on Croatian economy

International Nuclear Information System (INIS)

Kulisic, Biljana; Loizou, Efstratios; Rozakis, Stelios; Segon, Velimir

2007-01-01

The aim of this paper is to assess the direct and indirect impacts on a national economy from biodiesel (rapeseed methyl ester (RME)) production using input-output (I-O) analysis. Biodiesel development in Croatia is used as a case study. For Croatia, as for many other countries in Europe, biodiesel is a new activity not included in the existing I-O sectoral accounts. For this reason the I-O table has to be modified accordingly before being able to quantify the effect of an exogenous demand for biodiesel. Impacts in terms of output, income and employment lead to the conclusion that biodiesel production could have significant positive net impact on the Croatian economy despite the high level of subsidies for rapeseed growing

Application of response surface methodology for optimizing transesterification of Moringa oleifera oil: Biodiesel production

International Nuclear Information System (INIS)

Rashid, Umer; Anwar, Farooq; Ashraf, Muhammad; Saleem, Muhammad; Yusup, Suzana

2011-01-01

Highlights: → Biodiesel production from Moringa oil (MO) has been optimized for the first time using RSM. → RSM-optimized reaction conditions gave a high Moringa oil methyl esters (MOMEs) yield (94.3%). → Fuel properties of MOMEs yielded satisfied the ASTM D 6751 and EU 14214 specifications. → Present RSM-model can be useful for predicting optimum biodiesel yield from other oils. - Abstract: Response surface methodology (RSM), with central composite rotatable design (CCRD), was used to explore optimum conditions for the transesterification of Moringa oleifera oil. Effects of four variables, reaction temperature (25-65 deg. C), reaction time (20-90 min), methanol/oil molar ratio (3:1-12:1) and catalyst concentration (0.25-1.25 wt.% KOH) were appraised. The quadratic term of methanol/oil molar ratio, catalyst concentration and reaction time while the interaction terms of methanol/oil molar ratio with reaction temperature and catalyst concentration, reaction time with catalyst concentration exhibited significant effects on the yield of Moringa oil methyl esters (MOMEs)/biodiesel, p < 0.0001 and p < 0.05, respectively. Transesterification under the optimum conditions ascertained presently by RSM: 6.4:1 methanol/oil molar ratio, 0.80% catalyst concentration, 55 deg. C reaction temperature and 71.08 min reaction time offered 94.30% MOMEs yield. The observed and predicted values of MOMEs yield showed a linear relationship. GLC analysis of MOMEs revealed oleic acid methyl ester, with contribution of 73.22%, as the principal component. Other methyl esters detected were of palmitic, stearic, behenic and arachidic acids. Thermal stability of MOMEs produced was evaluated by thermogravimetric curve. The fuel properties such as density, kinematic viscosity, lubricity, oxidative stability, higher heating value, cetane number and cloud point etc., of MOMEs were found to be within the ASTM D6751 and EN 14214 biodiesel standards.

Application of response surface methodology for optimizing transesterification of Moringa oleifera oil: Biodiesel production

Energy Technology Data Exchange (ETDEWEB)

Rashid, Umer, E-mail: umer.rashid@yahoo.com [Department of Chemistry and Biochemistry, University of Agriculture, Faisalabad 38040 (Pakistan); Chemical Engineering Department, Universiti Teknologi PETRONAS, Bandar Seri Iskandar 31750, Tronoh, Perak (Malaysia); Anwar, Farooq, E-mail: fqanwar@yahoo.com [Department of Chemistry and Biochemistry, University of Agriculture, Faisalabad 38040 (Pakistan); Ashraf, Muhammad, E-mail: ashrafbot@yahoo.com [Department of Botany, University of Agriculture, Faisalabad 38040 (Pakistan); Department of Botany and Microbiology, King Saud University, Riyadh (Saudi Arabia); Saleem, Muhammad [Department of Statistics, Government College University, Faisalabad 38000 (Pakistan); Yusup, Suzana, E-mail: drsuzana_yusuf@petronas.com.my [Chemical Engineering Department, Universiti Teknologi PETRONAS, Bandar Seri Iskandar 31750, Tronoh, Perak (Malaysia)

2011-08-15

Highlights: {yields} Biodiesel production from Moringa oil (MO) has been optimized for the first time using RSM. {yields} RSM-optimized reaction conditions gave a high Moringa oil methyl esters (MOMEs) yield (94.3%). {yields} Fuel properties of MOMEs yielded satisfied the ASTM D 6751 and EU 14214 specifications. {yields} Present RSM-model can be useful for predicting optimum biodiesel yield from other oils. - Abstract: Response surface methodology (RSM), with central composite rotatable design (CCRD), was used to explore optimum conditions for the transesterification of Moringa oleifera oil. Effects of four variables, reaction temperature (25-65 deg. C), reaction time (20-90 min), methanol/oil molar ratio (3:1-12:1) and catalyst concentration (0.25-1.25 wt.% KOH) were appraised. The quadratic term of methanol/oil molar ratio, catalyst concentration and reaction time while the interaction terms of methanol/oil molar ratio with reaction temperature and catalyst concentration, reaction time with catalyst concentration exhibited significant effects on the yield of Moringa oil methyl esters (MOMEs)/biodiesel, p < 0.0001 and p < 0.05, respectively. Transesterification under the optimum conditions ascertained presently by RSM: 6.4:1 methanol/oil molar ratio, 0.80% catalyst concentration, 55 deg. C reaction temperature and 71.08 min reaction time offered 94.30% MOMEs yield. The observed and predicted values of MOMEs yield showed a linear relationship. GLC analysis of MOMEs revealed oleic acid methyl ester, with contribution of 73.22%, as the principal component. Other methyl esters detected were of palmitic, stearic, behenic and arachidic acids. Thermal stability of MOMEs produced was evaluated by thermogravimetric curve. The fuel properties such as density, kinematic viscosity, lubricity, oxidative stability, higher heating value, cetane number and cloud point etc., of MOMEs were found to be within the ASTM D6751 and EN 14214 biodiesel standards.

Biodiesel production by transesterification of duck tallow with methanol on alkali catalysts

Energy Technology Data Exchange (ETDEWEB)

Chung, Kyong-Hwan [Center for Functional Nano Fine Chemicals, Chonnam National University, Gwangju 500-757 (Korea); Kim, Jin [Center for Functional Nano Fine Chemicals, Chonnam National University, Gwangju 500-757 (Korea)]|[Department of Advanced Chemicals Graduate School, Chonnam National University, Gwangju 500-757 (Korea); Lee, Ki-Young [Center for Functional Nano Fine Chemicals, Chonnam National University, Gwangju 500-757 (Korea)]|[Department of Applied Chemical Engineering and The Research Institute for Catalysis, Chonnam National University, Gwangju 500-757 (Korea)

2009-01-15

Duck tallow was employed as a feedstock for the production of biodiesel by transesterification with methanol. The content of fatty acid methyl ester (FAME) was evaluated on various alkali catalysts during transesterification. The composition and chemical properties of the FAME were investigated in the raw duck tallow and the biodiesel products. The major constituent in the biodiesel product was oleic acid. The FAME content was 97% on KOH catalyst in the reaction. It was acceptable for the limit of European biodiesel qualities for BD100. Acid value, density, and kinematic viscosity of the biodiesel products also came up to the biodiesel qualities. (author)

THE EFFECT OF KARANJA OIL METHYL ESTER ON KIRLOSKAR HA394DI DIESEL ENGINE PERFORMANCE AND EXHAUST EMISSIONS

Directory of Open Access Journals (Sweden)

Sharanappa K Godiganur

2010-01-01

Full Text Available Biofuels are being investigated as potential substitutes for current high pollutant fuels obtained from the conventional sources. The primary problem associated with using straight vegetable oil as fuel in a compression ignition engine is caused by viscosity. The process of transesterifiction of vegetable oil with methyl alcohol provides a significant reduction in viscosity, thereby enhancing the physical properties of vegetable oil. The Kirloskar HA394 compression ignition, multi cylinder diesel engine does not require any modification to replace diesel by karanja methyl ester. Biodiesel can be used in its pure form or can be blended with diesel to form different blends. The purpose of this research was to evaluate the potential of karanja oil methyl ester and its blend with diesel from 20% to 80% by volume. Engine performance and exhaust emissions were investigated and compared with the ordinary diesel fuel in a diesel engine. The experimental results show that the engine power of the mixture is closed to the values obtained from diesel fuel and the amounts of exhaust emissions are lower than those of diesel fuel. Hence, it is seen that the blend of karanja ester and diesel fuel can be used as an alternative successfully in a diesel engine without any modification and in terms of emission parameters; it is an environmental friendly fuel

Modeling of the oxidation of methyl esters-Validation for methyl hexanoate, methyl heptanoate, and methyl decanoate in a jet-stirred reactor.

Science.gov (United States)

Glaude, Pierre Alexandre; Herbinet, Olivier; Bax, Sarah; Biet, Joffrey; Warth, Valérie; Battin-Leclerc, Frédérique

2010-11-01

The modeling of the oxidation of methyl esters was investigated and the specific chemistry, which is due to the presence of the ester group in this class of molecules, is described. New reactions and rate parameters were defined and included in the software EXGAS for the automatic generation of kinetic mechanisms. Models generated with EXGAS were successfully validated against data from the literature (oxidation of methyl hexanoate and methyl heptanoate in a jet-stirred reactor) and a new set of experimental results for methyl decanoate. The oxidation of this last species was investigated in a jet-stirred reactor at temperatures from 500 to 1100 K, including the negative temperature coefficient region, under stoichiometric conditions, at a pressure of 1.06 bar and for a residence time of 1.5 s: more than 30 reaction products, including olefins, unsaturated esters, and cyclic ethers, were quantified and successfully simulated. Flow rate analysis showed that reactions pathways for the oxidation of methyl esters in the low-temperature range are similar to that of alkanes.

Fast and simple method for determination of fatty acid methyl esters (FAME) in biodiesel blends using X-ray spectrometry.

Science.gov (United States)

Sitko, Rafal; Zawisza, Beata; Kowalewska, Zofia; Kocot, Karina; Polowniak, Marzena

2011-09-30

The determination of fatty acid methyl esters (FAME) in diesel fuel blends is an important aspect of production and blending process as well as quality control of distribution operations. In this study, energy-dispersive X-ray fluorescence spectrometer (EDXRF) is used for the first time for determination of FAME in biodiesel blends. The principle of the method is based on intensity difference of X-ray radiation scattered from hydrocarbons and from FAME. The experiment shows that coherent and incoherent radiation, commonly applied for evaluation of the average atomic number of the sample with light matrix, cannot be applied for FAME determination. However, the application of scattered continuous radiation gives excellent correlation between FAME concentration and intensity of scattered radiation. The best results are obtained if continuum is collected in the range of energy between 10.5 and 15.0 keV for rhodium X-ray tube, operated at 35 kV. Linear relationship between the FAME concentration and the inverse of scattered continuous radiation is obtained with the correlation coefficients of 0.999. Standard deviation of measurement is ca. 0.46% (v/v) of FAME and detection limit is 1.2% (v/v) for 600 s counting time and 50% dead-time loss using Si-PIN detector. The investigation shows that crucial issue in determination of FAME in biodiesel blends using EDXRF spectrometer is the precision of measurements resulting from the counting statistics. Therefore, much better results (0.20% (v/v) standard deviation and 0.52% (v/v) detection limit) can be expected if higher intensity of primary radiation is applied and X-ray spectrum is collected by silicon drift detector of high input count rate. For concentration of FAME from 10 to 100% (v/v), the differences between reference method (Fourier transform infrared spectrometry) and the proposed method usually do not exceed 1% (v/v) of FAME. The proposed method is fast, simple and enables FAME determination in wide range of

Experimental investigation on fuel properties of biodiesel prepared from cottonseed oil

Science.gov (United States)

Payl, Ashish Naha; Mashud, Mohammad

2017-06-01

In recent time's world's energy demands are satisfied by coal, natural gas as well as petroleum though the prices of these are escalating. If this continues, global recession is unavoidable and diminution of world reserve accelerates undoubtedly. Recently, Biodiesel is found to be more sustainable, non-toxic and energy efficient alternative which is also biodegradable. The use of biofuels in compression ignition engines is now a contemplation attention in place of petrochemicals. In view of this, cottonseed oil is quite a favorable candidate as an alternative fuel. The present study covers the various aspects of biodiesels fuel prepared from cottonseed oil. In this work Biodiesel was prepared from cottonseed oil through transesterification process with methanol, using sodium hydroxide as catalyst. The fuel properties of cottonseed oil methyl esters, kinematic viscosity, flash point, density, calorific value, boiling point etc. were evaluated and discussed in the light of Conventional Diesel Fuel. The properties of biodiesel produced from cotton seed oil are quite close to that of diesel except from flash point. And so the methyl esters of cottonseed oil can be used in existing diesel engines without any modifications.

Biodiesel development from rice bran oil: Transesterification process optimization and fuel characterization

International Nuclear Information System (INIS)

Sinha, Shailendra; Agarwal, Avinash Kumar; Garg, Sanjeev

2008-01-01

Increased environmental awareness and depletion of resources are driving industry to develop viable alternative fuels from renewable resources that are environmentally more acceptable. Vegetable oil is a potential alternative fuel. The most detrimental properties of vegetable oils are its high viscosity and low volatility, and these cause several problems during their long duration usage in compression ignition (CI) engines. The most commonly used method to make vegetable oil suitable for use in CI engines is to convert it into biodiesel, i.e. vegetable oil esters using process of transesterification. Rice bran oil is an underutilized non-edible vegetable oil, which is available in large quantities in rice cultivating countries, and very little research has been done to utilize this oil as a replacement for mineral Diesel. In the present work, the transesterification process for production of rice bran oil methyl ester has been investigated. The various process variables like temperature, catalyst concentration, amount of methanol and reaction time were optimized with the objective of producing high quality rice bran oil biodiesel with maximum yield. The optimum conditions for transesterification of rice bran oil with methanol and NaOH as catalyst were found to be 55 deg. C reaction temperature, 1 h reaction time, 9:1 molar ratio of rice bran oil to methanol and 0.75% catalyst (w/w). Rice bran oil methyl ester thus produced was characterized to find its suitability to be used as a fuel in engines. Results showed that biodiesel obtained under the optimum conditions has comparable properties to substitute mineral Diesel, hence, rice bran oil methyl ester biodiesel could be recommended as a mineral Diesel fuel substitute for compression ignition (CI) engines in transportation as well as in the agriculture sector

The emission analysis of an IDI diesel engine fueled with methyl ester of waste frying palm oil and its blends

Energy Technology Data Exchange (ETDEWEB)

Ozsezen, Ahmet Necati; Canakci, Mustafa [Department of Automotive Engineering Technology, Kocaeli University, 41380, Izmit (Turkey); Alternative Fuels R and D Center, Kocaeli University, 41275, Izmit (Turkey)

2010-12-15

In this study, the exhaust emissions of an unmodified diesel engine fueled with methyl ester of waste frying palm-oil (biodiesel) and its blends with petroleum based diesel fuel (PBDF) were investigated at the full load-variable speed condition. The relationships between the fuel properties and the air-fuel equivalence ratio, fuel line pressure, start of injection (SOI) timing, and ignition delay were also discussed to explain their effects on the emissions. The obtained test results were compared with the reference values which were determined by using PBDF. The results showed that when biodiesel was used in the test engine, the fuel line pressure increased while air-fuel equivalence ratio and ignition delay decreased. These behaviors affected the combustion phenomena of biodiesel which caused to reduction 57% in carbon monoxide (CO) emission, about 40% in unburned hydrocarbon (HC) emission and about 23% in smoke opacity when compared with PBDF. However, NO{sub x} and CO{sub 2} emissions of the biodiesel have showed different behaviors in terms of the engine speed. (author)

Catalytic Oxidation of Allylic Alcohols to Methyl Esters

DEFF Research Database (Denmark)

Gallas-Hulin, Agata; Kotni, Rama Krishna; Nielsen, Martin

2017-01-01

Aerobic oxidation of allylic alcohols to methyl esters using gold nanoparticles supported on different metal oxide carriers has been performed successfully under mild conditions (room temperature, 0.1 MPa O2) without significant loss of catalytic activity. The effects of different reaction...... parameters are studied to find the suitable reaction conditions. All catalysts are characterised by XRD, XRF and TEM. Among these catalysts, Au/TiO2 showed the most efficient catalytic activity towards the selective oxidation of allylic alcohols to the corresponding esters. Moreover, the same Au/TiO2...... to synthesize methyl esters from allylic alcohols....

Thermal stability of biodiesel in supercritical methanol

Energy Technology Data Exchange (ETDEWEB)

Hiroaki Imahara; Eiji Minami; Shusaku Hari; Shiro Saka [Kyoto University, Kyoto (Japan). Department of Socio-Environmental Energy Science

2008-01-15

Non-catalytic biodiesel production technologies from oils/fats in plants and animals have been developed in our laboratory employing supercritical methanol. Due to conditions in high temperature and high pressure of the supercritical fluid, thermal stability of fatty acid methyl esters and actual biodiesel prepared from various plant oils was studied in supercritical methanol over a range of its condition between 270{sup o}C/17 MPa and 380{sup o}C/56 MPa. In addition, the effect of thermal degradation on cold flow properties was studied. As a result, it was found that all fatty acid methyl esters including poly-unsaturated ones were stable at 270{sup o}C/17 MPa, but at 350{sup o}C/43 MPa, they were partly decomposed to reduce the yield with isomerization from cis-type to trans-type. These behaviors were also observed for actual biodiesel prepared from linseed oil, safflower oil, which are high in poly-unsaturated fatty acids. Cold flow properties of actual biodiesel, however, remained almost unchanged after supercritical methanol exposure at 270{sup o}C/17 MPa and 350{sup o}C/43 MPa. For the latter condition, however, poly-unsaturated fatty acids were sacrificed to be decomposed and reduced in yield. From these results, it was clarified that reaction temperature in supercritical methanol process should be lower than 300{sup o}C, preferably 270{sup o}C with a supercritical pressure higher than 8.09 MPa, in terms of thermal stabilization for high-quality biodiesel production. 9 refs., 3 figs., 4 tabs.

Fatty acid methyl esters synthesis from non-edible vegetable oils using supercritical methanol and methyl tert-butyl ether

International Nuclear Information System (INIS)

Lamba, Neha; Modak, Jayant M.; Madras, Giridhar

2017-01-01

Highlights: • FAMEs were synthesized from non-edible oils using supercritical MeOH and MTBE. • Effect of time, temperature, pressure and molar ratio on conversions was studied. • Rate constants of reaction with methanol and MTBE differ by an order of magnitude. • Non-catalytic supercritical reactions are one order faster than acid catalyzed synthesis. - Abstract: Fatty acid methyl esters (FAMEs) are useful as biodiesel and have environmental benefits compared to conventional diesel. In this study, these esters were synthesized non-catalytically from non-edible vegetable oils: neem oil and mahua oil with two different methylating agents: methanol and methyl tert-butyl ether (MTBE). The effects of temperature, pressure, time and molar ratio on the conversion of triglycerides were studied. The temperature was varied in the range of 523–723 K with molar ratios upto 50:1 and a reaction time of upto 150 min. Conversion of neem and mahua oil to FAMEs with supercritical methanol was found to be 83% in 15 min and 99% in 10 min, respectively at 698 K. Further, a conversion of 46% of mahua oil and 59% of neem oil was obtained in 15 min at 723 K using supercritical MTBE. The rate constants evaluated using pseudo first order reaction kinetics were in the range of 4.7 × 10"−"6 to 1.0 × 10"−"3 s"−"1 for the investigated range of temperatures. The activation energies obtained were in the range of 62–113 kJ/mol for the reaction systems investigated. The supercritical synthesis was found to be superior to the catalytic synthesis of the corresponding FAMEs.

Production of Methyl Laurate from Coconut Cream through Fractionation of Methyl Ester

Directory of Open Access Journals (Sweden)

Johnner P. Sitompul

2015-10-01

Full Text Available This paper concerns the production of methyl laurate from coconut cream through fractionation of methyl esters. Coconut oil was produced by wet processing of coconut cream. The esters were prepared by reacting coconut oil and methanol using homogeneous catalyst KOH in a batch reactor, followed by fractionation of fatty acid methyl esters (FAME at various reduced pressures applying differential batch vacuum distillation. Experimental data were compared with simulation of a batch distillation employing the simple Raoult’s model and modified Raoult’s model of phase equilibria. Activity coefficients (γi were determined by optimization to refine the models. The modified Rault’s model with activity coefficients gave better agreement with the experimental data, giving the value of γi between 0,56-0,73. For a given boiling temperature, lower operating pressure produced higher purity of C10 and C12 FAME for respective distillates.

Pumpkin (Cucurbita pepo L.) seed oil as an alternative feedstock for the production of biodiesel in Greece

Energy Technology Data Exchange (ETDEWEB)

Schinas, P.; Karavalakis, G.; Davaris, C.; Anastopoulos, G.; Karonis, D.; Zannikos, F.; Stournas, S.; Lois, E. [Laboratory of Fuels and Lubricants Technology, School of Chemical Engineering, National Technical University of Athens, 9 Iroon Polytechniou Street, Zografou Campus, 157 80 Athens (Greece)

2009-01-15

In recent years, the acceptance of fatty acid methyl esters (biodiesel) as a substitute to petroleum diesel has rapidly grown in Greece. The raw materials for biodiesel production in this country mainly include traditional seed oils (cotton seed oil, sunflower oil, soybean oil and rapeseed oil) and used frying oils. In the search for new low-cost alternative feedstocks for biodiesel production, this study emphasizes the evaluation of pumpkin seed oil. The experimental results showed that the oil content of pumpkin seeds was remarkably high (45%). The fatty acid profile of the oil showed that is composed primarily of linoleic, oleic, palmitic and stearic acids. The oil was chemically converted via an alkaline transesterification reaction with methanol to methyl esters, with a yield nearly 97.5 wt%. All of the measured properties of the produced biodiesel met the current quality requirements according to EN 14214. Although this study showed that pumpkin oil could be a promising feedstock for biodiesel production within the EU, it is rather difficult for this production to be achieved on a large scale. (author)

Utilization of rapeseed pellet from fatty acid methyl esters production as an energy source.

Science.gov (United States)

Ciunel, Krzysztof; Klugmann-Radziemska, Ewa

2014-01-01

Rapeseed pellet - crushed seed residue from oil extraction is a by-product of fatty acid methyl esters production process. As other types of biomass, it can either be burned directly in furnaces or processed to increase its energetic value. Biomass is renewable, abundant and has domestic usage; the sources ofbiomass can help the world reduce its dependence on petroleum products, fossil coal and natural gas. Energetically effective utilization of rapeseed pellet could substantially improve the economic balance of an individual household in which biodiesel for fulfilling the producer's own energetic demand is obtained. In this article, the experimental results of combusting rapeseed pellet in a calorimeter, combustion in a boiler heater and the analysis of the emissions level of different pollutants in exhaust fumes during different stages of biomass boiler operation are presented. It has been proved that the pellet, a by-product of biodiesel production, is not only a valuable substitute of animal fodder, but also an excellent renewable and environmentally friendly energy source, viable for use in household tap water heating installations.

A study on the 0D phenomenological model for diesel engine simulation: Application to combustion of Neem methyl esther biodiesel

International Nuclear Information System (INIS)

Ngayihi Abbe, Claude Valery; Nzengwa, Robert; Danwe, Raidandi; Ayissi, Zacharie Merlin; Obonou, Marcel

2015-01-01

Highlights: • We elaborate a 0D model for prediction of diesel engine operating parameters. • We implement the model for Neem methyl ester biodiesel combustion. • We show methyl butanoate and butyrate can be used as surrogates for biodiesel. • The model predicts fuel spray, in cylinder gaseous state and NOx emissions. • We show the model can be effective both in accuracy and computational speed. - Abstract: The design and monitoring of modern diesel engines running on alternative fuels require reliable models that can validly substitute experimental tests and predict their operating characteristics under different load conditions. Although there exists a multitude of models for diesel engines, 0D phenomenological models present the advantages of giving fast and accurate computed results. These models are useful for predicting fuel spray characteristics and instantaneous gas state. However, there are few reported studies on the application of 0D phenomenological models on biodiesel fuel combustion in diesel engines. This work reports the elaboration, validation and application on Neem methyl ester biodiesel (NMEB) combustion of a 0D phenomenological model for diesel engine simulation. The model addresses some specific aspects of diesel engine modeling found in previous studies such as the compromise between computers cost, accurateness and model simplicity, the reduction of the number of empirical fitting constant, the prediction of combustion kinetics with reduction of the need of experimental curve fitting, the ability to simultaneously predict under various loads engine thermodynamic and spray parameters as well as emission characteristics and finally the ability to simulate diesel engine parameters when fueled by alternative fuels. The proposed model predicts fuel spray behavior, in cylinder combustion and nitric oxides (NOx) emissions. The model is implemented through a Matlab code. The model is mainly based on Razlejtsev’s spray evaporation model

Binding of indomethacin methyl ester to cyclooxygenase-2. A computational study.

Science.gov (United States)

Sárosi, Menyhárt-Botond

2018-06-05

Inhibitors selective towards the second isoform of prostaglandin synthase (cyclooxygenase, COX-2) are promising nonsteroidal anti-inflammatory drugs and antitumor medications. Methylation of the carboxylate group in the relatively nonselective COX inhibitor indomethacin confers significant COX-2 selectivity. Several other modifications converting indomethacin into a COX-2 selective inhibitor have been reported. Earlier experimental and computational studies on neutral indomethacin derivatives suggest that the methyl ester derivative likely binds to COX-2 with a similar binding mode as that observed for the parent indomethacin. However, docking studies followed by molecular dynamics simulations revealed two possible binding modes in COX-2 for indomethacin methyl ester, which differs from the experimental binding mode found for indomethacin. Both alternative binding modes might explain the observed COX-2 selectivity of indomethacin methyl ester. Graphical abstract Binding of indomethacin methyl ester to cyclooxygenase-2.

Impact of residual glycerides on viscosity of biodiesel (waste and rapeseed oil blends)

OpenAIRE

Z. Jurac; L. Pomenić

2013-01-01

Purpose: Biodiesel, mixture of fatty acid methyl esters is a biodegradable alternative fuel that is obtained from renewable sources as a vegetable oils or animal fats. Use of waste cooking oils reduce the cost of raw materials for biodiesel production and also reduces the environment pollution. Moreover, pure edible vegetable oils for biodiesel production have an ethical significance because food is used to produce fuel. The aim of this work is a presentation of effects that r...

Ecological Impact of Biodiesel Use

International Nuclear Information System (INIS)

Gulbis, V.; Shmigins, R.

2005-01-01

Full text: The paper presents a study of biodiesel application and its ecological impacts. Our study is based on the comparison of exhaust emission composition produced by the combustion of rapeseed oil methyl ester (RME) and conventional diesel fuel (DD) and its blends in a direct injection diesel engine XD2P (YTT). The engine was tested in biofuels laboratory of LUA Motor Vehicle Institute. Fuelling the engine with biodiesel and biodiesel/diesel blend reduced oxides of nitrogen by 17.5% (100RME) and by 5.6% (35RME) and carbon monoxide by 49.8% (100RME) and by 45.3% (35RME). Fuelling the engine with biodiesel and different biodiesel/diesel blends reduced the absorbtion coefficient by 33.9% (5RME), by 44.3% (20RME) and by 51.2% (100RME) on free acceleration regime. In these tests soot reduced by 28...76.7% at full opened throttle position with 100RME. (Authors)

Use of calcium oxide in palm oil methyl ester production

Directory of Open Access Journals (Sweden)

Kulchanat Prasertsit

2014-04-01

Full Text Available Introducing an untreated calcium oxide (CaO as a solid heterogeneous catalyst for biodiesel production from palm oil by transesterification was studied in this work. The four studied parameters were methanol to oil molar ratio, CaO catalyst concentration, reaction time, and water content. The results for palm oil show that when the water content is higher than 3%wt and the amount of CaO greater than 7%wt soap formation from saponification occurs. A higher methanol to oil molar ratio requires a higher amount of CaO catalyst to provide the higher product purity. The appropriate methanol to CaO catalyst ratio is about 1.56. Commercial grade CaO gives almost the same results as AR grade CaO. In addition, reusing commercial grade CaO for about 5 to 10 repetitions without catalyst regeneration drops the percentage of methyl ester purity approximately 5 to 10%, respectively.

Oxidation stability of rapeseed biodiesel/petroleum diesel blends

DEFF Research Database (Denmark)

Østerstrøm, Freja From; Anderson, James E.; Mueller, Sherry A.

2016-01-01

of the oxidation of a biodiesel fuel blend consisting of 30% (v/v) rapeseed methyl ester in petroleum diesel (B30) was conducted at 70 and 90 °C with three aeration rates. Oxidation rates increased with increasing temperature as indicated by decreases in induction period (Rancimat), concentrations of unsaturated...

Biodiesel production from waste animal fat and improvement of its characteristics by synthesized nickel and magnesium additive

Energy Technology Data Exchange (ETDEWEB)

Guerue, Metin; Artukoglu, Bursev Dogan [Gazi University, Engineering and Architecture Faculty, Chemical Engineering Department, 06570 Ankara (Turkey); Keskin, Ali [Mersin University, Technical Education Faculty, 33500 Mersin (Turkey); Koca, Atilla [Gazi University, Technical Education Faculty, 06500 Ankara (Turkey)

2009-03-15

The purpose of this study is to produce trimethyl ester from waste animal fat at optimum conditions and improve its characteristics by synthesized nickel and magnesium additives. In this study, a two step catalytic process for synthesis of biodiesel was studied by reacting waste animal fats with methanol. The temperature, amount of methanol and type and amount of catalyst are investigated as parameters, and the changes in viscosity and flash point of animal fat biodiesel were determined. Furthermore, the effects of organic based Ni and Mg additives on the methyl ester pour point were specified. Optimum producing conditions were determined experimentally. At the end of these experiments, the maximum yield of 89% was obtained in two steps with total 0.35 (w/w) methanol/fat, at 62 {+-} 1 C reaction temperature for 2 h reaction period and by catalysing with 0.08 (w/w) H{sub 2}SO{sub 4}/fat and 0.01 (w/w) NaOH/fat ratios. Organic based metal compounds were synthesized by reacting abietic acid in the tall oil resinic acid with NiO and MgO compounds in order to improve the animal fat methyl ester characteristics. Reduction of the pour point was achieved by adding organic based nickel and magnesium compounds to biodiesel at a ratio of 12 {mu}mol/l oil methyl ester. Also, the blend of animal fat methyl ester-Diesel fuel was tested in a direct injection Diesel engine. The maximum effect of the new fuel blend on the engine performance was reached at 2200 min{sup -1} of engine torque. The lowest specific fuel consumptions were obtained at 2200 min{sup -1} for both fuels. (author)

Biodiesel production from waste animal fat and improvement of its characteristics by synthesized nickel and magnesium additive

International Nuclear Information System (INIS)

Guerue, Metin; Artukoglu, Bursev Dogan; Keskin, Ali; Koca, Atilla

2009-01-01

The purpose of this study is to produce trimethyl ester from waste animal fat at optimum conditions and improve its characteristics by synthesized nickel and magnesium additives. In this study, a two step catalytic process for synthesis of biodiesel was studied by reacting waste animal fats with methanol. The temperature, amount of methanol and type and amount of catalyst are investigated as parameters, and the changes in viscosity and flash point of animal fat biodiesel were determined. Furthermore, the effects of organic based Ni and Mg additives on the methyl ester pour point were specified. Optimum producing conditions were determined experimentally. At the end of these experiments, the maximum yield of 89% was obtained in two steps with total 0.35 (w/w) methanol/fat, at 62 ± 1 deg. C reaction temperature for 2 h reaction period and by catalysing with 0.08 (w/w) H 2 SO 4 /fat and 0.01 (w/w) NaOH/fat ratios. Organic based metal compounds were synthesized by reacting abietic acid in the tall oil resinic acid with NiO and MgO compounds in order to improve the animal fat methyl ester characteristics. Reduction of the pour point was achieved by adding organic based nickel and magnesium compounds to biodiesel at a ratio of 12 μmol/l oil methyl ester. Also, the blend of animal fat methyl ester-Diesel fuel was tested in a direct injection Diesel engine. The maximum effect of the new fuel blend on the engine performance was reached at 2200 min -1 of engine torque. The lowest specific fuel consumptions were obtained at 2200 min -1 for both fuels

Mitigating crystallization of saturated FAMEs in biodiesel 6: The binary phase behavior of 1, 2-dioleoyl-3-stearoyl sn-glycerol – Methyl stearate

International Nuclear Information System (INIS)

Mohanan, Athira; Bouzidi, Laziz; Narine, Suresh S.

2016-01-01

The derivatives of vegetable oils with specific chemical structures, such as TAG (triacylglycerols) having mixed straight and kinked moieties, have proven very effective in lowering the crystallization of biodiesel. SOO (1, 2-dioleoyl-3-stearoyl sn-glycerol)/MeS (methyl stearate) is part of a series of studies of TAG/FAME (fatty acid methyl ester) binary model systems conducted to establish structure–function relationships of lipid-based cold flow improvers in biodiesel with a particular attention to the effect of molecular symmetry in contrast with a previously published study of the OSO (1, 3-dioleoyl-2-stearoyl sn-glycerol)/MeS binary system. The phase behavior of several SOO/MeS mixtures were investigated at different length scales with XRD (X-ray diffraction), DSC (differential scanning calorimetry) and PLM (polarized light microscope). A complete phase diagram including the transformation lines, crystal structure and microstructure was constructed. The solubility behavior was discussed using a simple thermodynamic model based on the Hildebrand equation and pair interactions. The asymmetric position of the oleic moieties of SOO was shown to be crucial in modifying the thermal transformation behavior of MeS. The findings may be used to design effective crystallization modifiers of biodiesel based on particular structural determinants, and underscores the importance of symmetry in such designs. - Highlights: • Effect of symmetry of triglyceride on biodiesel crystallization established. • Complete phase diagram of model triacylglycerol/biodiesel binary system achieved. • Correlation between thermal transitions, crystal structure and microstructure revealed. • Transformation points useful for improving the cold flow of biodiesel identified. • Necessary knowledge gathered to design effective biodiesel cold flow improvers.

SINTESIS BIODIESEL DARI MINYAK MIKROALGA Chlorella vulgaris DENGAN REAKSI TRANSESTERIFIKASI MENGGUNAKAN KATALIS KOH

Directory of Open Access Journals (Sweden)

Catur Rini Widyastuti

2014-10-01

Full Text Available Biodiesel merupakan salah satu energi alternatif yang dianggap mampu menjawab permasalahan kelangkaan bahan bakar minyak. Biodiesel dapat disintesis dari minyak nabati melalui reaksi transesterifikasi. Sumber minyak nabati yang potensial adalah mikroalga yang memiliki produktifitas minyak yang lebih tinggi per satuan luas lahan yang digunakan jika dibandingkan dengan tanaman darat. Mikroalga jenis Chlorella sp diketahui mengandung komponen lipid cukup tinggi yaitu sebesar 14-22%. Langkah-langkah penelitian yang dilakukan meliputi ekstraksi minyak mikroalga dengan n-heksana, reaksi transesterifikasi minyak mikroalga dan metanol dengan katalis KOH, dilanjutkan dengan filtrasi untuk memisahkan produk biodiesel dengan gliserol yang terbentuk. Untuk mengetahui kandungan kimia dalam bahan baku dan produk, minyak hasil ekstraksi mikroalga dan biodiesel yang dihasilkan dianalisis dengan GC-MS. Dari hasil uji GC-MS diketahui dua kandungan asam lemak terbesar dalam minyak mikroalga, yaitu Dodecanoic acid sebesar 59.52% dan n-Decanoic acid sebesar 12.64%. Dari proses transesterifikasi, yield biodiesel yang diperoleh sebesar 59.85% dengan densitas 0.88 g/cm3. Kandungan kimia biodiesel diketahui terdiri dari senyawa Fatty Acid Methyl Ester (FAME sebesar 15.4% dan Fatty Acid Ethyl Ester (FAEE sebesar 21.14%.Biodiesel is one of the alternative energy which expected to provide a solution towards our dependence of fossil fuel. Biodiesel could be synthesized from vegetable oil through transesterification process. One of the most potential sources of vegetable oil is microalgae which is more productive than a land-based plant. One of the species of microalgae which is Chlorella sp is known for containing high lipid content from 14 to 22%. The steps of the research including extraction of microalgae oil using n-hexane, transesterification reaction between microalgae and methanol using KOH as a catalyst, and continued by filtration to separate the biodiesel product

Improvement in biodiesel production from soapstock oil by one-stage lipase catalyzed methanolysis

International Nuclear Information System (INIS)

Su, Erzheng; Wei, Dongzhi

2014-01-01

Highlights: • Soapstock is a less expensive feedstock reservoir for biodiesel production. • Addition of tert-alcohol can enhance the yield of fatty acid methyl ester significantly. • One-stage lipase catalyzed methanolysis of soapstock oil was successfully developed. • FAME yield of 95.2% was obtained with low lipase loading in a shorter reaction time. - Abstract: A major obstacle in the commercialization of biodiesel is its cost of manufacturing, primarily the raw material cost. In order to decrease the cost of biodiesel, soapstock oil was investigated as the feedstock for biodiesel production. Because the soapstock oil containing large amounts of free fatty acids (FFAs) cannot be effectively converted to biodiesel, complicated two-stage process (esterification followed by transesterification) was generally adopted. In this study, simple one-stage lipase catalyzed methanolysis of soapstock oil was developed via one-pot esterification and transesterification. Water produced by lipase catalyzed esterification of FFAs affected the lipase catalyzed transesterification of glycerides in the soapstock oil severely. Addition of tert-alcohol could overcome this problem and enhance the fatty acid methyl ester (FAME) yield from 42.8% to 76.4%. The FAME yield was further elevated to 95.2% by optimizing the methanol/oil molar ratio, lipase amount, and water absorbent. The developed process enables the simple, efficient, and green production of biodiesel from soapstock oil, providing with a potential industrial application

COMPARISON OF BIODIESEL PRODUCTIVITIES OF DIFFERENT VEGETABLE OILS BY ACIDIC CATALYSIS

Directory of Open Access Journals (Sweden)

AYTEN SAGIROGLU

2011-03-01

Full Text Available Biodiesel has become a subject which increasingly attracts worldwide attention because of its environmental benefits, biodegradability and renewability. Biodiesel production typically involves the transesterification of a triglyceride feedstock with methanol or other short-chain alcohols. This paper presents a study of transesterification of various vegetable oils, sunflower, safflower, canola, soybean, olive, corn, hazelnut and waste sunflower oils, with the acidic catalyst. Under laboratory conditions, fatty acid methyl esters (FAME were prepared by using methanol in the presence of 1.85% hydrochloric acid at 100 °C for 1 h and 25 °C for 3 h. The analyses of biodiesel were carried out by gas chroma¬tography and thin layer chromatography. Also, biodiesel productivities (% were determined on basis of the ratio of ester to oil content (w/w. The biodiesel productivities for all oils were found to be about 80% and about 90% at 25 and 100 °C, respectively. Also, the results showed that the yield of biodiesel depended on temperature for some oils, including canola, sunflower, safflower oils, but it was not found significant differences among all of the oil types on biodiesel productivities.

Enzymatic Production of FAME Biodiesel with Soluble Lipases

DEFF Research Database (Denmark)

T. Gundersen, Maria; Heltborg, Carsten Kirstejn; Yang, V

Biodiesel is a viable alternative to fossil fuels, and biocatalysis is gaining interest as a greener process. We focus on converting oils to Fatty Acid Methyl Ester (FAME) using soluble lipases, which offer an advantage compared to immobilized enzymes by cost efficiency and ease of implementation...... the defined operating space concerning: temperature, water content, initial methanol concentration and enzyme content. The identified optimum range was experimentally evaluated, and model findings were confirmed. Another barrier in lipase use in biodiesel production is the higher melting point (m...

Synthesis of 11C labelled methyl esters: transesterification of enol esters versus BF3 catalysed esterification-a comparative study

International Nuclear Information System (INIS)

Ackermann, Uwe; Blanc, Paul; Falzon, Cheryl L.; Issa, William; White, Jonathan; Tochon-Danguy, Henri J.; Sachinidis, John I.; Scott, Andrew M.

2006-01-01

C-11 labelled methyl esters have been synthesized via the transesterification of enol esters in the presence of C-11 methanol and 1,3 dichlorodibutylstannoxane as catalyst. This method leaves functional groups intact and allows access to a wider variety of C-11 labelled methyl esters compared to the BF 3 catalysed ester formation, which uses carboxylic acids and C-11 methanol as starting materials

Process engineering and optimization of glycerol separation in a packed-bed reactor for enzymatic biodiesel production.

Science.gov (United States)

Hama, Shinji; Tamalampudi, Sriappareddy; Yoshida, Ayumi; Tamadani, Naoki; Kuratani, Nobuyuki; Noda, Hideo; Fukuda, Hideki; Kondo, Akihiko

2011-11-01

A process model for efficient glycerol separation during methanolysis in an enzymatic packed-bed reactor (PBR) was developed. A theoretical glycerol removal efficiency from the reaction mixture containing over 30% methyl esters was achieved at a high flow rate of 540 ml/h. To facilitate a stable operation of the PBR system, a batch reaction prior to continuous methanolysis was conducted using oils with different acid values and immobilized lipases pretreated with methyl esters. The reaction system successfully attained the methyl ester content of over 30% along with reduced viscosity and water content. Furthermore, to obtain a high methyl ester content above 96% continuously, long-term lipase stability was confirmed by operating a bench-scale PBR system for 550 h, in which the intermediates containing methyl esters and residual glycerides were fed into the enzyme-packed columns connected in series. Therefore, the developed process model is considered useful for industrial biodiesel production. Copyright © 2011 Elsevier Ltd. All rights reserved.

Engineering Escherichia coli for Biodiesel Production Utilizing a Bacterial Fatty Acid Methyltransferase▿†

Science.gov (United States)

Nawabi, Parwez; Bauer, Stefan; Kyrpides, Nikos; Lykidis, Athanasios

2011-01-01

The production of low-cost biofuels in engineered microorganisms is of great interest due to the continual increase in the world's energy demands. Biodiesel is a renewable fuel that can potentially be produced in microbes cost-effectively. Fatty acid methyl esters (FAMEs) are a common component of biodiesel and can be synthesized from either triacylglycerol or free fatty acids (FFAs). Here we report the identification of a novel bacterial fatty acid methyltransferase (FAMT) that catalyzes the formation of FAMEs and 3-hydroxyl fatty acid methyl esters (3-OH-FAMEs) from the respective free acids and S-adenosylmethionine (AdoMet). FAMT exhibits a higher specificity toward 3-hydroxy free fatty acids (3-OH-FFAs) than FFAs, synthesizing 3-hydroxy fatty acid methyl esters (3-OH-FAMEs) in vivo. We have also identified bacterial members of the fatty acyl-acyl carrier protein (ACP) thioesterase (FAT) enzyme family with distinct acyl chain specificities. These bacterial FATs exhibit increased specificity toward 3-hydroxyacyl-ACP, generating 3-OH-FFAs, which can subsequently be utilized by FAMTs to produce 3-OH-FAMEs. PhaG (3-hydroxyacyl ACP:coenzyme A [CoA] transacylase) constitutes an alternative route to 3-OH-FFA synthesis; the coexpression of PhaG with FAMT led to the highest level of accumulation of 3-OH-FAMEs and FAMEs. The availability of AdoMet, the second substrate for FAMT, is an important factor regulating the amount of methyl esters produced by bacterial cells. Our results indicate that the deletion of the global methionine regulator metJ and the overexpression of methionine adenosyltransferase result in increased methyl ester synthesis. PMID:21926202

Highly active CaO for the transesterification to biodiesel production ...

African Journals Online (AJOL)

TMCS) for transesterification of rapeseed oil and methanol to biodiesel production was studied. It was found that the fatty acid methyl esters (FAME) yield of the modified CaO was greatly enhanced from 85.4% to 94.6% under 65 oC with 15:1 ...

Thermophysical properties of biodiesel and related systems: (Liquid + liquid) equilibrium data for soybean biodiesel

International Nuclear Information System (INIS)

Mazutti, Marcio A.; Voll, Fernando A.P.; Cardozo-Filho, Lúcio; Corazza, Marcos L.; Lanza, Marcelo; Priamo, Wagner L.; Oliveira, J. Vladimir

2013-01-01

Highlights: ► (Liquid + liquid) equilibrium data for the systems of biodiesel production. ► LLE data for multicomponent FAME and FAEE from (303.15 to 333.15) K. ► Experimental data correlated using the UNIQUAC model. -- Abstract: This work reports (liquid + liquid) equilibrium (LLE) data for the systems of interest in soybean biodiesel production. Numerical data for LLE were obtained for binary, ternary and quaternary systems comprising fatty acid methyl esters (FAME) and fatty acid ethyl esters (FAEE) from soybean oil, water, glycerol, methanol, and ethanol at temperatures of (303.15, 318.15, and 333.15) K. Quantification of compounds in equilibrium in both phases was determined by analytical methods whereas solubility curves (binodal) were obtained by the cloud-point method. For all systems investigated, good alignments were obtained between phase compositions and the initial as well as overall compositions hence indicating low deviations from the mass balance. Experimental results were correlated using the UNIQUAC model with satisfactory agreement between experiment and theory

Metodologia experimental para avaliação de custos de produção e utilização de biodiesel: estudo de caso de quatro ésteres metílicos e óleo diesel comercial Experimental methodology for assessing the cost of biodiesel production and use biodiesel: a case study of four methyl esters and commercial diesel fuel

Directory of Open Access Journals (Sweden)

Diego Augusto Fiorese

2011-11-01

Full Text Available Considerando que o Brasil detém uma vasta gama de matérias-primas para produção de biodiesel, e também que há a possibilidade de produção em pequena escala, prima-se por estudos de cunho econômico a partir de metodologias de fácil execução. O objetivo do trabalho foi demonstrar uma metodologia e sua aplicação para avaliação dos custos inseridos dentro do processo produtivo e de utilização do biodiesel. A metodologia foi aplicada a biodieseis originários de óleo de soja, girassol, frango e sebo bovino, dos quais se avaliaram economicamente os custos fixos e variáveis para conversão química dos óleos e gorduras em ésteres metílicos, em uma planta de produção experimental. Os custos de produção para cada uma das quatro citadas são distintos em função do valor inicial por litro de cada uma. Também fora avaliado o custo específico e o consumo específico de cada um dos biodieseis, a fim de determinar a diferença em relação ao óleo diesel comercial. No estudo de caso, os resultados mostraram vantagens para o óleo diesel, tanto no custo quanto no consumo. Comparando-se os biodieseis, o de sebo bovino apresentou-se com o menor custo de produção e o menor consumo.Considering that Brazil has a wide range of raw materials for biodiesel production, and also the possibility of small scale production, there is a demand for economic methodology studies with easy implementation. The objective of this research was to demonstrate a methodology and its application to assess the costs within the production process and the biodiesel use. The methodology was applied to biodiesels originated from soybean oil, sunflower oil, chicken oil and beef tallow, which assessed the fixed and variable costs for chemical conversion of oils and fats into methyl esters in an experimental production plant. Production costs for each of the four mentioned esters are peculiar due to the initial value of each oil per liter. Also the specific cost

Evaluation of engine performance and emission with methyl ester of Karanja oil

Directory of Open Access Journals (Sweden)

Shikha Gangil

2016-09-01

Full Text Available Biodiesel has been considered as potential alternative to petroleum diesel with the renewable origin for the existing compression ignition engine. The main objective of the present work is evaluating performance and emission characteristics of diesel engine for various blends (B20, B40, B60, B80 and B100 of Karanja biodiesel and commercial diesel. The experimental investigation was carried out in IC (internal combustion at variable loads and compared with conventional diesel fuel with respect to engine performance parameters i.e. brake specific fuel consumption (BSFC, brake specific power consumption (BSEC, brake thermal efficiency (η-B.Th, for varying load conditions. The results obtained indicated the better fuel properties and engine performance at B40. For all cases, BSFC reduced with increase in load. It can be observed that the BSEC for various blends is lower as compared with that of diesel fuel. The availability of oxygen in the Karanja oil methyl ester-diesel fuel blend may be the reason for the lower BSEC. Brake thermal efficiency is increased due reduced heat loss with increased in load. It was found that the emission level of CO and HC level decreased with increased in blend proportion in diesel fuel. NOx emission increased with increase in blend proportion in diesel fuel.

Impact of increasing the blend ratio of biodiesel on engine emissions associated toxicity : A quick scan by RIVM and TNO

NARCIS (Netherlands)

Gerlofs-Nijland ME; Vercruijsse W; Cassee FR; Janssen P; Kadijk G; Kooter IM; Verbeek RP; Zyl PS; Jedynska AD; Koornneef GP; M&G; M&V

2014-01-01

Er zijn geen sterke aanwijzingen dat het bijmengen van FAME ("Fatty Acid Methyl Ester") biodiesel tot 7 vol%1 en HVO ("Hydrotreated Vegetable Oil") biodiesel tot 30 vol% zal leiden tot significante toename van schadelijke uitstoot van het wegverkeer. Deze conclusie is gebaseerd op de beperkte

Synthesis of heterogeneous catalyst for the production of biodiesel ...

African Journals Online (AJOL)

This study explore the comparison of a suitable heterogeneous catalyst for conversion of triglyceride into fatty acid methyl ester. A series of heterogeneous cerium, manganese, and zinc oxide catalyst supported at mixture of cinder was prepared by co-precipitation and applied for conversion of triglyceride in oil to biodiesel ...

Performance and emission characteristics of a stationary diesel engine fuelled by Schleichera Oleosa Oil Methyl Ester (SOME) produced through hydrodynamic cavitation process

OpenAIRE

Ashok Kumar Yadav; M. Emran Khan; Amit Pal; Uttam Ghosh

2018-01-01

In this study, the performance and emission characteristics of biodiesel blends of 10, 20, 30 and 50% from Schleichera Oleosa oil based on hydrodynamic cavitation were compared to diesel fuel, and found to be acceptable according to the EN 14214 and ASTM D 6751 standards. The tests have been performed using a single cylinder four stroke diesel engine at different loading condition with the blended fuel at the rated speed of 1500 rpm. SOME (Schleichera Oleosa Oil Methyl Ester) blended with die...

Improving the sustainability of fatty acid methyl esters (Fame – biodiesel) – assessment of options for industry and agriculture

NARCIS (Netherlands)

Jungmeier, G.; Pucker, J.; Ernst, M.; Haselbacher, P.; Lesschen, J.P.; Kraft, A.; Schulzke, T.; Loo, van E.N.

2016-01-01

The life cycle based greenhouse gas (GHG) balances of Fatty Acid Methyl Esters (FAME also called “Biodiesel”) from various resources have been set in the Renewable Energy Directive (RED). Due to technology and scientific progress there are various options to improve the GHG balances of FAME. In

Experimental (liquid + liquid) equilibrium data for ternary and quaternary mixtures of fatty acid methyl and ethyl esters (FAME/FAEE) from soybean oil

International Nuclear Information System (INIS)

Beneti, Stéphani C.; Lanza, Marcelo; Mazutti, Marcio A.; Kunita, Marcos Hiroiuqui; Cardozo-Filho, Lúcio; Vladimir Oliveira, J.

2014-01-01

Highlights: • Innovative technique for quantification of compounds involved in the biodiesel production. • Easy and quick determination from NIR combined with multivariate calibration. • Reliable LLE correlation and predictions can be attained from the technique. -- Abstract: This work is aimed at providing an easy and quick determination of the biodiesel products using near infrared spectroscopy (NIR) by combination with the multivariate calibration in the analysis of (liquid + liquid) equilibrium (LLE) data for ternary and quaternary mixtures containing soybean fatty acid methyl (FAME) and ethyl (FAEE) esters, glycerol, ethanol, methanol and water, at various temperatures. The mass balance for the compositions obtained for each phase was carried out so as to demonstrate the reliability of the models generated by the multivariate calibration. Two distinct phases are observed, a glycerol-rich and the other ester-rich, while ethanol is dissolved among the phases hence reducing the partial mutual miscibility between glycerol and ester. Through (liquid + liquid) equilibrium (LLE) results, systems containing FAEE at T = 318.15 K and 303.15 K (calibration using data obtained at temperature of 318.15 K), a good agreement is verified among the values determined using conventional and NIR technique for alcoholic phase (AP) or aqueous phase (WP) and biodiesel phase (BP). Likewise in the systems containing FAME at 318.15 K, 303.15 K and 333.15 K (calibration using data obtained at temperature of 318.15 K), the LLE results were reproduced at the upper and lower temperature to the tests of the reproducibility of the models generated by the multivariate calibration

Bacillus sp. PS35 Lipase-Immobilization on Styrene-Divinyl Benzene Resin and Application in Fatty Acid Methyl Ester Synthesis.

Science.gov (United States)

Palanisamy, Kanmani; Kuppamuthu, Kumaresan; Jeyaseelan, Aravind

2015-09-01

Lipase is an enzyme with immense application potential. Ester synthesis by lipase catalysis in organic media is an area of key industrial relevance. Enzymatic preparations with traits that cater to the needs of this function are hence being intensely researched. The objectives of the study were to immobilize the lipase from Bacillus sp. PS35 by cross-linking and adsorption onto styrene-divinyl benzene (Sty-Dvb) hydrophobic resin and to comparatively characterize the free and immobilized lipase preparations. The work also aimed to apply the immobilized lipase for catalysing the fatty acid methyl ester (FAME) synthesis from palm oil and optimize the process parameters for maximizing the yield. In this study, the purified lipase from Bacillus sp. PS35 was immobilized by adsorption onto styrene-divinyl benzene hydrophobic resin with gluteraldehyde cross-linking. The immobilized enzyme showed better pH and temperature stabilities than the free lipase. Organic solvent stability was also enhanced, with the relative activity in the presence of methanol being shifted from 53% to 81%, thereby facilitating the enzyme's application in fatty acid methyl ester synthesis. It exhibited remarkable storage stability over a 30-day period and after 20 repetitive uses. Cross-linking also reduced enzyme leakage by 49%. The immobilized lipase was then applied for biodiesel production from palm oil. Methanol and oil molar ratio of 5:1, three step methanol additions, and an incubation temperature of 50°C were established to be the ideal conditions favoring the transesterification reaction, resulting in 97% methyl ester yield. These promising results offer scope for further investigation and process scale up, permitting the enzyme's commercial application in a practically feasible and economically agreeable manner.

Performance evaluation of common rail direct injection (CRDI engine fuelled with Uppage Oil Methyl Ester (UOME

Directory of Open Access Journals (Sweden)

D.N. Basavarajappa

2015-02-01

Full Text Available For economic and social development of any country energy is one of the most essential requirements. Continuously increasing price of crude petroleum fuels in the present days coupled with alarming emissions and stringent emission regulations has led to growing attention towards use of alternative fuels like vegetable oils, alcoholic and gaseous fuels for diesel engine applications. Use of such fuels can ease the burden on the economy by curtailing the fuel imports. Diesel engines are highly efficient and the main problems associated with them is their high smoke and NOx emissions.  Hence there is an urgent need to promote the use of alternative fuels in place of high speed diesel (HSD as substitute. India has a large agriculture base that can be used as a feed stock to obtain newer fuel which is renewable and sustainable. Accordingly Uppage oil methyl ester (UOME biodiesel was selected as an alternative fuel. Use of biodiesels in diesel engines fitted with mechanical fuel injection systems has limitation on the injector opening pressure (300 bar. CRDI system can overcome this drawback by injecting fuel at very high pressures (1500-2500 bar and is most suitable for biodiesel fuels which are high viscous. This paper presents the performance and emission characteristics of a CRDI diesel engine fuelled with UOME biodiesel at different injection timings and injection pressures. From the experimental evidence it was revealed that UOME biodiesel yielded overall better performance with reduced emissions at retarded injection timing of -10° BTDC in CRDI mode of engine operation.

Performance evaluation of common rail direct injection (CRDI engine fuelled with Uppage Oil Methyl Ester (UOME

Directory of Open Access Journals (Sweden)

D.N. Basavarajappa

2015-02-01

Full Text Available For economic and social development of any country energy is one of the most essential requirements. Continuously increasing price of crude petroleum fuels in the present days coupled with alarming emissions and stringent emission regulations has led to growing attention towards use of alternative fuels like vegetable oils, alcoholic and gaseous fuels for diesel engine applications. Use of such fuels can ease the burden on the economy by curtailing the fuel imports. Diesel engines are highly efficient and the main problems associated with them is their high smoke and NOx emissions. Hence there is an urgent need to promote the use of alternative fuels in place of high speed diesel (HSD as substitute. India has a large agriculture base that can be used as a feed stock to obtain newer fuel which is renewable and sustainable. Accordingly Uppage oil methyl ester (UOME biodiesel was selected as an alternative fuel. Use of biodiesels in diesel engines fitted with mechanical fuel injection systems has limitation on the injector opening pressure (300 bar. CRDI system can overcome this drawback by injecting fuel at very high pressures (1500-2500 bar and is most suitable for biodiesel fuels which are high viscous. This paper presents the performance and emission characteristics of a CRDI diesel engine fuelled with UOME biodiesel at different injection timings and injection pressures. From the experimental evidence it was revealed that UOME biodiesel yielded overall better performance with reduced emissions at retarded injection timing of -10° BTDC in CRDI mode of engine operation.

De novo biosynthesis of biodiesel by Escherichia coli in optimized fed-batch cultivation.

Directory of Open Access Journals (Sweden)

Yangkai Duan

Full Text Available Biodiesel is a renewable alternative to petroleum diesel fuel that can contribute to carbon dioxide emission reduction and energy supply. Biodiesel is composed of fatty acid alkyl esters, including fatty acid methyl esters (FAMEs and fatty acid ethyl esters (FAEEs, and is currently produced through the transesterification reaction of methanol (or ethanol and triacylglycerols (TAGs. TAGs are mainly obtained from oilseed plants and microalgae. A sustainable supply of TAGs is a major bottleneck for current biodiesel production. Here we report the de novo biosynthesis of FAEEs from glucose, which can be derived from lignocellulosic biomass, in genetically engineered Escherichia coli by introduction of the ethanol-producing pathway from Zymomonas mobilis, genetic manipulation to increase the pool of fatty acyl-CoA, and heterologous expression of acyl-coenzyme A: diacylglycerol acyltransferase from Acinetobacter baylyi. An optimized fed-batch microbial fermentation of the modified E. coli strain yielded a titer of 922 mg L(-1 FAEEs that consisted primarily of ethyl palmitate, -oleate, -myristate and -palmitoleate.

Chlorococcalean microalgae Ankistrodesmus convolutes biodiesel characterization with Fourier transform-infrared spectroscopy and gas chromatography mass spectroscopy techniques

Directory of Open Access Journals (Sweden)

Swati SONAWANE

2015-12-01

Full Text Available The Chlorococcalean microalgae Ankistrodesmus convolutes was found in fresh water Godawari reservoir, Ahmednagar district of Maharashtra State, India. Microalgae are modern biomass for the production of liquid biofuel due to its high solar cultivation efficiency. The collection, harvesting and drying processes were play vital role in converting algal biomass into energy liquid fuel. The oil extraction was the important step for the biodiesel synthesis. The fatty acid methyl ester (FAME synthesis was carried through base catalyzed transesterification method. The product was analyzed by using the hyphened techniques like Fourier Transform-Infrared spectroscopy (FT-IR and Gas Chromatography Mass Spectroscopy (GCMS. FT-IR Spectroscopy was results the ester as functional group of obtained product while the Gas Chromatography Mass Spectroscopy was results the six type of fatty acid methyl ester with different concentration. Ankistrodesmus convolutes biodiesel consist of 46.5% saturated and 49.14% unsaturated FAME.

Influence the Rubber Seed Type and Altitude on Characteristic of Seed, Oil and Biodiesel

Directory of Open Access Journals (Sweden)

Salni Salni

2017-06-01

Full Text Available This research studies the influence of the type of rubber seed that is superior and local, altitude plant in South Sumatra province to the characteristic of seed, oil and biodiesel (methyl ester. Rubber plants planted from local rubber seed by seeds seedlings and superior rubber seed by selected clones. In the study, rubber plants planted at a different altitude, namely in Banyuasin district (18 m above sea level, Prabumulih District (176 m above sea level and Lahat District (627 m above sea level. The results showed that the weight of the flour, the water content and ash content in the local rubber seeds larger than the superior rubber seed for all altitude, but oil content a large in the superior rubber seeds. The major of fatty acids in the rubber seed oil in all types and altitude are a linoleic acid with a different percentage except local rubber seed oil from Lahat district with the large percentage of octadecanoic acid. Free fatty acids in the oil from the superior seeds rubber of 13.897-15.494 % large than local rubber seed oil was found 9.786-10.399 % for all altitude. By esterification process using sulfuric acid catalyst, Free Fatty Acid (FFA can be reduced to ≤ 2 %. The methyl ester made from the transesterification process of rubber seed oil after esterification using methanol and sodium hydroxide as catalyst. Analysis of methyl esters includes cetane index, flash point, kinematic viscosity, carbon residue, density, moisture content, water and sediment content and distillation compared with SNI 7182 and ASTM 6751-02.  The result indicated that the quality of methyl ester from superior rubber seed oil in the Banyuasin and Prabumulih district better than another methyl ester. The types of rubber seed altitude affect the characteristics of the seed, oil and methyl ester  but the altitude are not significantly different. Keywords: rubber seed, type, altitude, oil, biodiesel Article History: Received March 21st 2017; Received in

Effect of biodiesel unsaturated fatty acid on combustion characteristics of a DI compression ignition engine

Energy Technology Data Exchange (ETDEWEB)

Puhan, Sukumar [Department of Mechanical Engineering, Veltech Engineering college, Avadi, Chennai (India); Saravanan, N. [ERC Engines, Tata Motors, Pimpri, Pune (India); Nagarajan, G. [Department of Mechanical Engineering, Anna University, Chennai (India); Vedaraman, N. [Chemical Engineering Division, Central Leather Research Institute, Adyar, Chennai (India)

2010-08-15

Several research works have been carried out on biodiesel combustion, performance and emissions till today. But very few studies have been made about the chemistry of biodiesel that affects the diesel engine operation. Biodiesel is derived from vegetable oil or animal fats, which comprises of several fatty acids with different chain length and bonding. The present work focuses on the effect of biodiesel molecular weight, structure (Cis and Trans), and the number of double bonds on the diesel engine operation characteristics. Three types of biodiesel with different molecular weight and number of double bond were selected for the experimental studies. The biodiesels were prepared and analyzed for fuel properties according to the standards. A constant speed diesel engine, which develops 4.4 kW of power, was run with biodiesels and its performance was compared with diesel fuel. The results show that Linseed oil methyl ester with high linolenic (unsaturated fatty acid ester) does not suit best for diesel engine due to high oxides of nitrogen emission and low thermal efficiency. (author)

Direct conversion of wet algae to crude biodiesel under supercritical ethanol conditions

Energy Technology Data Exchange (ETDEWEB)

Reddy, Harvind K. [New Mexico State Univ., Las Cruces, NM (United States). Chemical Engineering Dept.; Muppaneni, Tapaswy [New Mexico State Univ., Las Cruces, NM (United States). Chemical Engineering Dept.; Patil, Prafulla D. [American Refining Group, Inc., Bradford, PA (United States); Ponnusamy, Sundaravadivelnathan [New Mexico State Univ., Las Cruces, NM (United States). Chemical Engineering Dept.; Cooke, Peter [New Mexico State Univ., Las Cruces, NM (United States). Core University Research Resource Lab.; Schaub, Tanner [New Mexico State Univ., Las Cruces, NM (United States). Bio Security and Food Safety Center; Deng, Shuguang [New Mexico State Univ., Las Cruces, NM (United States). Chemical Engineering Dept.

2013-08-06

This paper presents a single-step, environmentally friendly approach for the direct conversion of wet algae to crude biodiesel under supercritical ethanol conditions. Ethanol was used for the simultaneous extraction and transesterification of lipids in algae to produce fatty acid ethyl esters at supercritical conditions. In this work the effects of process parameters dry algae to ethanol (wt./vol.) ratio (1:6-1:15), reaction temperature (245-270 C), and reaction time (2-30 min.) on the yield of fatty acid ethyl esters (FAEE) were studied. 67% conversion was achieved at 265 C and 20 min of reaction time. The calorific value of a purified biodiesel sample produced at optimum conditions was measured to be 43 MJ/kg, which is higher than that of fatty acid methyl esters produced from the same biomass. The purified fatty acid ethyl esters were analyzed using GC-MS and FTIR. TGA analysis of algal biomass and purified FAEE was presented along with TEM images of the biomass captured before and after supercritical ethanol transesterification. This green conversion process has the potential to provide an energy-efficient and economical route for the production of renewable biodiesel production.

Alternative fuel properties of tall oil fatty acid methyl ester-diesel fuel blends

Energy Technology Data Exchange (ETDEWEB)

Altiparmak, D.; Keskin, A.; Koca, A. [Gazi University, Ankara (Turkey). Technical Education Faculty; Guru, M. [Gazi University, Ankara (Turkey). Engineering and Architectural Faculty

2007-01-15

In this experimental work, tall oil methyl ester-diesel fuel blends as alternative fuels for diesel engines were studied. Tall oil methyl ester was produced by reacting tall oil fatty acids with methyl alcohol under optimum conditions. The blends of tall oil methyl ester-diesel fuel were tested in a direct injection diesel engine at full load conditions. The effects of the new fuel blends on the engine performance and exhaust emission were tested. It was observed that the engine torque and power output with tall oil methyl ester-diesel fuel blends increased up to 6.1% and 5.9%, respectively. It was also seen that CO emissions decreased to 38.9% and NO{sub x} emissions increased up to 30% with the new fuel blends. The smoke capacity did not vary significantly. (author)

Alternative fuel properties of tall oil fatty acid methyl ester-diesel fuel blends.

Science.gov (United States)

Altiparmak, Duran; Keskin, Ali; Koca, Atilla; Gürü, Metin

2007-01-01

In this experimental work, tall oil methyl ester-diesel fuel blends as alternative fuels for diesel engines were studied. Tall oil methyl ester was produced by reacting tall oil fatty acids with methyl alcohol under optimum conditions. The blends of tall oil methyl ester-diesel fuel were tested in a direct injection diesel engine at full load condition. The effects of the new fuel blends on the engine performance and exhaust emission were tested. It was observed that the engine torque and power output with tall oil methyl ester-diesel fuel blends increased up to 6.1% and 5.9%, respectively. It was also seen that CO emissions decreased to 38.9% and NO(x) emissions increased up to 30% with the new fuel blends. The smoke opacity did not vary significantly.

Biodiesel production from waste cotton seed oil using low cost catalyst: Engine performance and emission characteristics

Directory of Open Access Journals (Sweden)

Duple Sinha

2016-09-01

Full Text Available Production of fatty acid methyl esters from waste cotton seed oil through transesterification was reported. The GC–MS analysis of WCCO oil was studied and the major fatty acids were found to be palmitic acid (27.76% and linoleic acid (42.84%. The molecular weight of the oil was 881.039 g/mol. A maximum yield of 92% biodiesel was reported when the reaction temperature, time, methanol/oil ratio and catalyst loading rate were 60 °C, 50 min, 12:1 and 3% (wt.%, respectively. The calcined egg shell catalyst was prepared and characterized. Partial purification of the fatty acid methyl esters was proposed for increasing the purity of the biodiesel and better engine performance. The flash point and the fire point of the biodiesel were found to be 128 °C and 136 °C, respectively. The Brake thermal efficiency of WCCO B10 biodiesel was 26.04% for maximum load, specific fuel consumption for diesel was 0.32 kg/kW h at maximum load. The use of biodiesel blends showed a reduction of carbon monoxide and hydrocarbon emissions and a marginal increase in nitrogen oxides (NOx emissions improved emission characteristics.

Process Parameters Optimization of Potential SO42-/ZnO Acid Catalyst for Heterogeneous Transesterification of Vegetable Oil to Biodiesel

Directory of Open Access Journals (Sweden)

Istadi Istadi

2012-12-01

Full Text Available Among the possible renewable energy resources, diesel fuels derived from triglycerides of vegetable oils and animal fats have shown potential as substitutes for petroleum-based diesel fuels. The biodiesel could be produced from vegetable oils over homogeneous catalyst, heterogeneous catalyst, or enzymatic catalyst. In this study, the synthesized SO42-/ZnO catalyst was explored to be used in the heterogeneous biodiesel production by using the vegetable oils and methanol. The study began with the preparation of SO42-/ZnO catalyst followed by the transesterification reaction between vegetable oil with methanol. The independent variables (reaction time and the weight ratio of catalyst/oil were optimized to obtain the optimum biodiesel (fatty acid methyl ester yield. The results of this study showed that the acid catalyst SO42-/ZnO was potential to be used as catalyst for biodiesel production through heterogeneous transesterification of vegetable oils. Optimum operating condition for this catalytic reaction was the weight ratio of catalyst/oil of 8:1 and reaction time of 2.6 h with respect to 75.5% yield of methyl ester products. The biodiesel product was also characterized to identify the respected fatty acid methyl ester components. Copyright © 2012 by BCREC UNDIP. All rights reserved. (Selected Paper from International Conference on Chemical and Material Engineering (ICCME 2012Received: 23rd October 2012, Revised: 25th November 2012, Accepted: 25th November 2012[How to Cite: I. Istadi, Didi D. Anggoro, Luqman Buchori, Inshani Utami, Roikhatus Solikhah, (2012. Process Parameters Optimization of Potential SO42-/ZnO Acid Catalyst for Heterogeneous Transesterification of Vegetable Oil to Biodiesel. Bulletin of Chemical Reaction Engineering & Catalysis, 7(2: 150-157. (doi:10.9767/bcrec.7.2.4064.150-157][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.7.2.4064.150-157 ] | View in 

Process development for scum to biodiesel conversion.

Science.gov (United States)

Bi, Chong-hao; Min, Min; Nie, Yong; Xie, Qing-long; Lu, Qian; Deng, Xiang-yuan; Anderson, Erik; Li, Dong; Chen, Paul; Ruan, Roger

2015-06-01

A novel process was developed for converting scum, a waste material from wastewater treatment facilities, to biodiesel. Scum is an oily waste that was skimmed from the surface of primary and secondary settling tanks in wastewater treatment plants. Currently scum is treated either by anaerobic digestion or landfilling which raised several environmental issues. The newly developed process used a six-step method to convert scum to biodiesel, a higher value product. A combination of acid washing and acid catalyzed esterification was developed to remove soap and impurities while converting free fatty acids to methyl esters. A glycerol washing was used to facilitate the separation of biodiesel and glycerin after base catalyzed transesterification. As a result, 70% of dried and filtered scum was converted to biodiesel which is equivalent to about 134,000 gallon biodiesel per year for the Saint Paul waste water treatment plant in Minnesota. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biodiesel wash-water reuse using microfiltration: toward zero-discharge strategy for cleaner and economized biodiesel production

Directory of Open Access Journals (Sweden)

R. Jaber

2015-03-01

Full Text Available A simple but economically feasible refining method to treat and re-use biodiesel wash-water was developed. In detail, microfiltration (MF through depth-filtration configuration was used in different hybrid modules. Then, the treated wash-water was mixed with clean water at different ratios, re-used for biodiesel purification and water-washing efficiency was evaluated based on methyl ester purity analysis. The findings of the present study revealed that depth-filtration-based MF combined with sand filtration/activated carbon separation and 70% dilution rate with fresh water not only achieved standard-quality biodiesel product but also led to up to 15% less water consumption after two rounds of production operations. This would be translated into a considerable reduction in the total volume of fresh water used during the operation process and would also strengthen the environmental-friendly aspects of the biodiesel production process for wastewater generation was obviously cut by the same rate as well.

Production of Biodiesel Using a Membrane Reactor to Minimize Separation Cost

Science.gov (United States)

Olagunju, O. A.; Musonge, P.

2017-07-01

This study investigates the performance of a packed bed membrane reactor in the transesterification process of triglycerides to methyl ester using soyabean oil as feedstock. A TiO2/Al2O3 ceramic microporous membrane was selected due to its chemical inert nature and thermal stability to selectively remove the product from the reaction medium. CaO impregnated on the surface of activated carbon was packed into the membrane and acted as catalyst. The synthesized catalyst had a total loading of 40.50 % and was characterized by XRD and temperature-programmed desorption of CO2 (CO2-TPD). The crude biodiesel produced was micro-filtered by the ceramic membrane with a pore size of 0.02 μm to retain the unreacted oil and free glycerol, at the transmembrane pressure of 100 KPa. The best condition was achieved with a temperature of 65 °C, methanol/oil molar ratio of 6:1 for 150 minutes, which resulted in the highest FAME yield of 94 %. Methyl ester produced met the ASTM D6751 and SANS 1935 specifications. The product obtained was mainly composed of methyl esters. Glycerol was not detected in the product stream due to the ability of the membrane to retain the glycerol and the unreacted oil in the medium, which solved the issue of glycerol separation from biodiesel.

Cultivation of algae in photobioreator and obtention of biodiesel

Directory of Open Access Journals (Sweden)

Cristiane B. Hobuss

2011-04-01

Full Text Available In this work we described the cultivation of Chlorella vulgaris in a photobioreactor to algal biomass production. The dried biomass was used as feedstock for biodiesel production, it presented 26% lipids and via sonocatalysis stage of the methodology resulted in 60% of fatty acid methyl esters (FAME. The FAME content was confirmed by Gas Chromatography (GC.

Biodiesel production from tall oil with synthesized Mn and Ni based additives: effects of the additives on fuel consumption and emissions

Energy Technology Data Exchange (ETDEWEB)

Ali Keskin; Metin Guru; Duran Altiparmak [Mersin University, Mersin (Turkey). Technical Education Faculty

2007-05-15

In this study, biodiesel fuel and fuel additives were produced from crude tall oil that is a by-product in the pulp manufacturing by craft or sulphate pulping process. Fatty acids and resinic acids were obtained from crude tall oil by distillation method. Tall oil methyl ester (biodiesel) was produced from fatty acids. Resinic acids were reacted with NiO and MnO{sub 2} stoichiometrically for production of metallic fuel additives. Each metallic fuel additive was added at the rate of 8 {mu}mol/l and 12 {mu}mol/l to make mixtures of 60% tall oil methyl ester/40% diesel fuel (TE60) for preparing test fuels. Metallic fuel additives improved properties of biodiesel fuels, such as pour point and viscosity values. Biodiesel fuels were tested in an unmodified direct injection diesel engine at full load condition. Specific fuel consumption of biodiesel fuels increased by 6.00%, however, in comparison with TE60, it showed trend of decreasing with adding of additives. Exhaust emission profile of biodiesel fuels improved. CO emissions and smoke opacity decreased up to 64.28% and 30.91% respectively. Low NOx emission was also observed in general for the biodiesel fuels. 28 refs., 4 figs., 3 tabs.

Proposed kinetic mechanism of biodiesel production through lipase catalysed interesterification with a methyl acetate acyl acceptor and ionic liquid BMIM PF6 co-solvent

Energy Technology Data Exchange (ETDEWEB)

Ruzich, Nicholas Ivan; Bassi, A.S.

2011-02-15

As the depletion of fossil resources continues, the demand for environmentally friendly sources of energy as biodiesel is increasing. Biodiesel is the resulting fatty acid methyl ester (FAME) from an esterification reaction. To enhance this reaction lipase catalysts and ionic liquids can also used. The aim of this study was to develop a kinetic model of this reaction and to determine the effect of ionic liquids. The esterification reaction was conducted in a jacketed reactor under constant temperature in presence of ionic liquid and with the use of lipase to start the reaction; samples were analyzed with a high-performance liquid chromatography. A kinetic model was developed and results indicated that ionic liquids tend to limit mass transfer and thus reduce initial reaction rates; the authors proposed to increase the flow rate of the reaction mixture to overcome this issue. This study successfully investigated the reaction of lipase-catalyzed biodiesel production and developed its kinetic model.

Effects of mixing technologies on continuous methyl ester production: Comparison of using plug flow, static mixer, and ultrasound clamp

International Nuclear Information System (INIS)

Somnuk, Krit; Prasit, Tanongsak; Prateepchaikul, Gumpon

2017-01-01

Highlights: • Four types of continuous reactors were compared with methyl ester conversion. • Plug flow, static mixer, ultrasound clamp, SM with ultrasound reactors were tested. • The 16 × 400 W ultrasound clamps were operated at 20 kHz frequency for US reactor. • The US reactor was clearly superior over the other types of continuous reactor. • The US reactor was the most effective alternative with short reactor length. - Abstract: Four types of continuous reactors, namely plug flow reactor (PF), static mixer reactor (SM), ultrasound clamp on tubular reactor (US), and static mixer combined with ultrasound (SM/US) were compared for their purities of methyl ester in biodiesel production from refined palm oil (RPO). The reactor conditions were: KOH 4, 6, 8, 10, and 12 g L −1 , methanol content 20 vol.%, and under 20 L h −1 RPO flow rate at 60 °C temperature. The highest purity of methyl esters: 81.99 wt.% for PF, 95.70 wt.% for SM, 98.98 wt.% for US, and 97.67 wt.% for SM/US, were achieved with 900 mm, 900 mm, 700 mm, and 900 mm reactor lengths respectively, and 12 g L −1 of KOH was used in all cases. The 16 × 400 W ultrasound clamp was operated at 20 kHz frequency, and among short length reactors the US case was more effective than PF, SM, or SM/US. Moreover, ester purity from the US reactor was slightly decreased by the lowest 4 g L −1 KOH. The US reactor was clearly superior over the other types of continuous reactor, and had the potential to reduce KOH consumption by sonochemical effects on the base-catalyzed transesterification reaction.

Supported phosphate and carbonate salts for heterogeneous catalysis of triglycerides to fatty acid methyl esters

Science.gov (United States)

Britton, Stephanie Lynne

Fatty acid methyl esters made from vegetable oil, or biodiesel, have been identified as a substitute for diesel derived from crude oil. Biodiesel is currently made using a homogeneous base catalyst to perform the transesterification of triglycerides with methanol to generate fatty acid methyl esters (FAME). The use of a homogeneous catalyst necessitates additional purification of the product and byproducts before sale, and the catalyst is consumed and discarded. The development of a heterogeneous basic catalyst for the production of FAME is desirable. Tribasic phosphate salts and dibasic carbonate salts are active for the production of FAME but generally operate as homogeneous catalysts. Supporting these phosphate and carbonate salts on mesoporous MCM-41, microporous silica gel, and nonporous a-alumina proved successful to greater or lesser degrees depending on the identity of the support and pretreatment of the support. Although these salts were supported and were active for the production of FAME from canola oil, they proved to be operating as homogeneous catalysts due to leaching of the active species off the surface of the support. Further investigation of the active species present in the tribasic phosphate catalysts identified the active support as orthophosphate, and NMR studies revealed the phosphorus to be present as orthophosphate and diphosphate in varying proportions in each catalyst. Evaluation of the acid-washing support pretreatment process revealed that the exposure of the support to acid plays a large role in the development of activity on the surface of the catalyst, but manipulation of these parameters did not prevent leaching of the active site off the surface of the catalyst. Alternate methods of support pretreatment were no more effective in preventing leaching. Tribasic phosphate supported on silica gel is not effective as a heterogeneous catalyst for FAME production from triglycerides because of the lack of stability of the phosphate on the

Convenient synthesis of 6-nor-9,10-dihydrolysergic acid methyl ester.

Science.gov (United States)

Crider, A M; Grubb, R; Bachmann, K A; Rawat, A K

1981-12-01

6-Nor-9,10-dihydrolysergic acid methyl ester (IV) was prepared by demethylation of 9,10-dihydrolysergic acid methyl ester (II) with 2,2,2-trichloroethyl chloroformate, followed by reduction of the intermediate carbamate (III) with zinc in acetic acid. The 6-ethyl-V and 6-n-propyl-VI derivatives were prepared by alkylation of IV with the appropriate halide. All of the ergoline derivatives were evaluated for stereotyped behavior in rats, with 6-nor-6-ethyl-9,10-dihydrolysergic acid methyl ester (V) being active but much less potent than apomorphine. Compound VI was evaluated for its effect on blood pressure; at a dose of 30 mg/kg ip, it significantly lowered, diastolic pressure in normotensive rats.

Complex formation of technetium with the methyl esters of MAG2 and MAG1

International Nuclear Information System (INIS)

Noll, B.; Noll, S.; Grosse, B.; Johannsen, B.; Spies, H.

1993-01-01

Mercaptoacetylglycine methyl ester (MAG 2 ester) and mercaptoacetyldiglycine methyl ester (MAG 1 ester) were included to investigate complex formation of SH/amide ligands with technetium. The studies are aimed at finding out how blocking the carboxylic groups influences the complexation reaction, with a view to finding an approach to new lipophilic species. (orig./BBR)

Influence of oxygen enrichment on compression ignition engines using biodiesel blends

Directory of Open Access Journals (Sweden)

Vaiyapuri Senthil Murugan

2017-01-01

Full Text Available The influence of oxygen enrichment on performance and emission characteristics of a single cylinder diesel engine operated with biodiesel blends have been investigated in this work. The methyl ester of jatropha biodiesel was selected as bio-diesel and four blends (B10, B20, B30, and B40 were selected for experimental investigations. The performance and emission characteristics were obtained for the these blends along with three oxygen enrichment flow rates (1, 3, and 5 L per minute using an oxygen cylinder at the air intake in the diesel engine. The performance and emission characteristics were studied and compared with the diesel and biodiesel. It was observed that, oxygen enrichment enhances the brake thermal efficiency, HC, CO, and smoke. B10 biodiesel with 5 L per minute oxygen enrichment was found to be the best fuel for biodiesel operation.

From Fed-batch to Continuous Enzymatic Biodiesel Production

DEFF Research Database (Denmark)

Price, Jason Anthony; Nordblad, Mathias; Woodley, John M.

2015-01-01

In this this paper, we use mechanistic modelling to guide the development of acontinuous enzymatic process that is performed as a fed-batch operation. In this workwe use the enzymatic biodiesel process as a case study. A mechanistic model developedin our previous work was used to determine...... measured components (triglycerides, diglycerides, monoglycerides, free fatty acid and fatty acid methyl esters(biodiesel)) much better than using fed-batch data alone given the smaller residuals. We also observe a reduction in the correlation between the parameters.The model was then used to predict that 5...... reactors are required (with a combined residence time of 30 hours) to reach a final biodiesel concentration within 2 % of the95.6 mass % achieved in a fed-batch operation, for 24 hours....

Soot measurements for diesel and biodiesel spray combustion under high temperature highly diluted ambient conditions

KAUST Repository

Zhang, Ji; Jing, Wei; Roberts, William L.; Fang, Tiegang

2014-01-01

This paper presents the soot temperature and KL factor for biodiesel, namely fatty acid methyl ester (FAME) and diesel fuel combustion in a constant volume chamber using a two-color technique. The KL factor is a parameter for soot concentration

Biodiesel Derive Bio-oil of Hermetia illucens Pre-pupae Catalysed by Sulphonated Biochar

Directory of Open Access Journals (Sweden)

Leong Siew Yoong

2018-01-01

Full Text Available This study investigates the development of biochar catalyst from bamboo applied for biodiesel synthesis. A non-conventional biodiesel feedstock was used in the in-situ transesterification reaction. This non-conventional feedstock is obtained from an insect’s fly, the Hermetia illucens fly. Biochar derived from bamboo has been investigated as a promising catalyst for biodiesel synthesis. The biochar acid catalysts were prepared by sulphonation via impregnation with concentrated sulphuric acid. The prepared catalysts were investigated for their performance to catalyse in-situ transesterification via ultra-sonication of Hermetia illucens bio-oil. The effects of carbonisation time (1 hour and 2 hour and temperature (400°C, 500°C and 600°C as well as catalyst loading (5-20 wt% on oil basis on the transesterification yield were studied. Result showed that the highest yield of FAME obtained was 95.6% with catalyst loading of 15 wt% carbonized at 500°C for 2 hours. Sharp band of methyl ester functional groups were observed in the FTIR spectra at 1735-1750cm-1. The composition of this methyl ester was further deduced using gas chromatography and the fatty acid was predominantly lauric acid.

Biodiesel Derive Bio-oil of Hermetia illucens Pre-pupae Catalysed by Sulphonated Biochar

Science.gov (United States)

Yoong Leong, Siew; Chong, Soo Shin; Chin, Kah Seng

2018-03-01

This study investigates the development of biochar catalyst from bamboo applied for biodiesel synthesis. A non-conventional biodiesel feedstock was used in the in-situ transesterification reaction. This non-conventional feedstock is obtained from an insect's fly, the Hermetia illucens fly. Biochar derived from bamboo has been investigated as a promising catalyst for biodiesel synthesis. The biochar acid catalysts were prepared by sulphonation via impregnation with concentrated sulphuric acid. The prepared catalysts were investigated for their performance to catalyse in-situ transesterification via ultra-sonication of Hermetia illucens bio-oil. The effects of carbonisation time (1 hour and 2 hour) and temperature (400°C, 500°C and 600°C) as well as catalyst loading (5-20 wt% on oil basis) on the transesterification yield were studied. Result showed that the highest yield of FAME obtained was 95.6% with catalyst loading of 15 wt% carbonized at 500°C for 2 hours. Sharp band of methyl ester functional groups were observed in the FTIR spectra at 1735-1750cm-1. The composition of this methyl ester was further deduced using gas chromatography and the fatty acid was predominantly lauric acid.

History and policy of biodiesel in Brazil

International Nuclear Information System (INIS)

Pousa, Gabriella P.A.G.; Santos, Andre L.F.; Suarez, Paulo A.Z.

2007-01-01

Historically, during petroleum shortage, vegetable oils and their derivatives have been proposed as alternatives to petroleum diesel fuel. Since 1930, different approaches have been proposed by Brazilian's universities and research institutes, including the use of neat vegetable oils (pure or in blends) or their derivatives, such as hydrocarbons obtained by thermal-catalytic cracking and fatty acids' methyl or ethyl esters (nowadays known as 'biodiesel') produced by alcoholysis. Recently, the external dependence on imported diesel fuel and the present petroleum crisis have increased the discussion in Brazil in the sense of starting to use alternatives to diesel fuel, biodiesel being the main alternative for a large petroleum diesel substitution program

Fungal production of single cell oil using untreated copra cake and evaluation of its fuel properties for biodiesel.

Science.gov (United States)

Khot, Mahesh; Gupta, Rohini; Barve, Kadambari; Zinjarde, Smita; Govindwar, Sanjay; Kumar, Ameeta Ravi

2015-04-01

This study evaluated the microbial conversion of coconut oil waste, a major agro-residue in tropical countries, into single cell oil (SCO) feedstock for biodiesel production. Copra cake was used as a low-cost renewable substrate without any prior chemical or enzymatic pretreatment for submerged growth of an oleaginous tropical mangrove fungus, Aspergillus terreus IBB M1. The SCO extracted from fermented biomass was converted into fatty acid methyl esters (FAMEs) by transesterification and evaluated on the basis of fatty acid profiles and key fuel properties for biodiesel. The fungus produced a biomass (8.2 g/l) yielding 257 mg/g copra cake SCO with ~98% FAMEs. The FAMEs were mainly composed of saturated methyl esters (61.2%) of medium-chain fatty acids (C12-C18) with methyl oleate (C18:1; 16.57%) and methyl linoleate (C18:2; 19.97%) making up the unsaturated content. A higher content of both saturated FAMEs and methyl oleate along with the absence of polyunsaturated FAMEs with ≥4 double bonds is expected to impart good fuel quality. This was evident from the predicted and experimentally determined key fuel properties of FAMEs (density, kinematic viscosity, iodine value, acid number, cetane number), which were in accordance with the international (ASTM D6751, EN 14214) and national (IS 15607) biodiesel standards, suggesting their suitability as a biodiesel fuel. The low cost, renewable nature, and easy availability of copra cake, its conversion into SCO without any thermochemical pretreatment, and pelleted fungal growth facilitating easier downstream processing by simple filtration make this process cost effective and environmentally favorable.

Enzymatic biodiesel synthesis. Key factors affecting efficiency of the process

Energy Technology Data Exchange (ETDEWEB)

Szczesna Antczak, Miroslawa; Kubiak, Aneta; Antczak, Tadeusz; Bielecki, Stanislaw [Institute of Technical Biochemistry, Faculty of Biotechnology and Food Sciences, Technical University of Lodz, Stefanowskiego 4/10, 90-924 Lodz (Poland)

2009-05-15

Chemical processes of biodiesel production are energy-consuming and generate undesirable by-products such as soaps and polymeric pigments that retard separation of pure methyl or ethyl esters of fatty acids from glycerol and di- and monoacylglycerols. Enzymatic, lipase-catalyzed biodiesel synthesis has no such drawbacks. Comprehension of the latter process and an appreciable progress in production of robust preparations of lipases may soon result in the replacement of chemical catalysts with enzymes in biodiesel synthesis. Engineering of enzymatic biodiesel synthesis processes requires optimization of such factors as: molar ratio of substrates (triacylglycerols: alcohol), temperature, type of organic solvent (if any) and water activity. All of them are correlated with properties of lipase preparation. This paper reports on the interplay between the crucial parameters of the lipase-catalyzed reactions carried out in non-aqueous systems and the yield of biodiesel synthesis. (author)

Synthesis of biodiesel from waste cooking oil using immobilized lipase in fixed bed reactor

Energy Technology Data Exchange (ETDEWEB)

Chen Yingming [School of Environment and Urban Construction, Wuhan University of Science and Engineering, Wuhan 430073 (China); Guangzhou Institute of Energy Conversion, Chinese Academy of Science, Guangzhou 510640 (China); Xiao Bo [School of Environmental Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Chang Jie [School of Chemistry and Chemical Engineering, South China University of Technology, Guangzhou 510641 (China)], E-mail: changjie@scut.edu.cn; Fu Yan [School of Chemistry and Chemical Engineering, South China University of Technology, Guangzhou 510641 (China); Lv Pengmei; Wang Xuewei [Guangzhou Institute of Energy Conversion, Chinese Academy of Science, Guangzhou 510640 (China)

2009-03-15

Waste cooking oil (WCO) is the residue from the kitchen, restaurants, food factories and even human and animal waste which not only harm people's health but also causes environmental pollution. The production of biodiesel from waste cooking oil to partially substitute petroleum diesel is one of the measures for solving the twin problems of environment pollution and energy shortage. In this project, synthesis of biodiesel was catalyzed by immobilized Candida lipase in a three-step fixed bed reactor. The reaction solution was a mixture of WCO, water, methanol and solvent (hexane). The main product was biodiesel consisted of fatty acid methyl ester (FAME), of which methyl oleate was the main component. Effects of lipase, solvent, water, and temperature and flow of the reaction mixture on the synthesis of biodiesel were analyzed. The results indicate that a 91.08% of FAME can be achieved in the end product under optimum conditions. Most of the chemical and physical characters of the biodiesel were superior to the standards for 0 diesel (GB/T 19147) and biodiesel (DIN V51606 and ASTM D-6751)

Synthesis of biodiesel from waste cooking oil using immobilized lipase in fixed bed reactor

Energy Technology Data Exchange (ETDEWEB)

Chen, Yingming [School of Environment and Urban Construction, Wuhan University of Science and Engineering, Wuhan 430073 (China)]|[Guangzhou Institute of Energy Conversion, Chinese Academy of Science, Guangzhou 510640 (China); Xiao, Bo [School of Environmental Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Chang, Jie; Fu, Yan [School of Chemistry and Chemical Engineering, South China University of Technology, Guangzhou 510641 (China); Lv, Pengmei; Wang, Xuewei [Guangzhou Institute of Energy Conversion, Chinese Academy of Science, Guangzhou 510640 (China)

2009-03-15

Waste cooking oil (WCO) is the residue from the kitchen, restaurants, food factories and even human and animal waste which not only harm people's health but also causes environmental pollution. The production of biodiesel from waste cooking oil to partially substitute petroleum diesel is one of the measures for solving the twin problems of environment pollution and energy shortage. In this project, synthesis of biodiesel was catalyzed by immobilized Candida lipase in a three-step fixed bed reactor. The reaction solution was a mixture of WCO, water, methanol and solvent (hexane). The main product was biodiesel consisted of fatty acid methyl ester (FAME), of which methyl oleate was the main component. Effects of lipase, solvent, water, and temperature and flow of the reaction mixture on the synthesis of biodiesel were analyzed. The results indicate that a 91.08% of FAME can be achieved in the end product under optimum conditions. Most of the chemical and physical characters of the biodiesel were superior to the standards for 0diesel (GB/T 19147) and biodiesel (DIN V51606 and ASTM D-6751). (author)

Synthesis of biodiesel from waste cooking oil using immobilized lipase in fixed bed reactor

International Nuclear Information System (INIS)

Chen Yingming; Xiao Bo; Chang Jie; Fu Yan; Lv Pengmei; Wang Xuewei

2009-01-01

Waste cooking oil (WCO) is the residue from the kitchen, restaurants, food factories and even human and animal waste which not only harm people's health but also causes environmental pollution. The production of biodiesel from waste cooking oil to partially substitute petroleum diesel is one of the measures for solving the twin problems of environment pollution and energy shortage. In this project, synthesis of biodiesel was catalyzed by immobilized Candida lipase in a three-step fixed bed reactor. The reaction solution was a mixture of WCO, water, methanol and solvent (hexane). The main product was biodiesel consisted of fatty acid methyl ester (FAME), of which methyl oleate was the main component. Effects of lipase, solvent, water, and temperature and flow of the reaction mixture on the synthesis of biodiesel were analyzed. The results indicate that a 91.08% of FAME can be achieved in the end product under optimum conditions. Most of the chemical and physical characters of the biodiesel were superior to the standards for 0 diesel (GB/T 19147) and biodiesel (DIN V51606 and ASTM D-6751)

Variation of diesel soot characteristics by different types and blends of biodiesel in a laboratory combustion chamber

Energy Technology Data Exchange (ETDEWEB)

Omidvarborna, Hamid; Kumar, Ashok [Department of Civil Engineering, The University of Toledo, Toledo, OH (United States); Kim, Dong-Shik, E-mail: dong.kim@utoledo.edu [Department of Chemical and Environmental Engineering, The University of Toledo, Toledo, OH (United States)

2016-02-15

Very little information is available on the physical and chemical properties of soot particles produced in the combustion of different types and blends of biodiesel fuels. A variety of feedstock can be used to produce biodiesel, and it is necessary to better understand the effects of feedstock-specific characteristics on soot particle emissions. Characteristics of soot particles, collected from a laboratory combustion chamber, are investigated from the blends of ultra-low sulfur diesel (ULSD) and biodiesel with various proportions. Biodiesel samples were derived from three different feedstocks, soybean methyl ester (SME), tallow oil (TO), and waste cooking oil (WCO). Experimental results showed a significant reduction in soot particle emissions when using biodiesel compared with ULSD. For the pure biodiesel, no soot particles were observed from the combustion regardless of their feedstock origins. The overall morphology of soot particles showed that the average diameter of ULSD soot particles is greater than the average soot particles from the biodiesel blends. Transmission electron microscopy (TEM) images of oxidized soot particles are presented to investigate how the addition of biodiesel fuels may affect structures of soot particles. In addition, inductively coupled plasma mass spectrometry (ICP-MS), Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) were conducted for characterization of soot particles. Unsaturated methyl esters and high oxygen content of biodiesel are thought to be the major factors that help reduce the formation of soot particles in a laboratory combustion chamber. - Highlights: • The unsaturation of biodiesel fuel was correlated with soot characteristics. • Average diameters of biodiesel soot were smaller than that of ULSD. • Eight elements were detected as the marker metals in biodiesel soot particles. • As the degree of unsaturation increased, the oxygen content in FAMEs increased. • Biodiesel

Synthesis and Analysis of Methacryloyl-L-Alanine Methyl Ester using fourier Transform Nuclear Magnetic Resonance

International Nuclear Information System (INIS)

Tri Darwinto

2008-01-01

Methacryloyl-L-alanine methyl ester was synthesized by reacting methacrylic acid with L-alanine methyl ester hydrochloride in triethylamine at temperature of 90 o C. Hydrogel polymer of poly(methacryloyl-L-alanine methyl ester) was much used for diagnosis and therapy of vascular tumor. The molecular structure methacryloyl-L-alanine methyl ester analyzed by fourier transform nuclear magnetic resonance (FT-NMR) for analyzing of carbon atom ( 13 C) using Distortionless Enhancement by Polarization Transfer (DEPT) measurement mode with coupling as well as without coupling from proton atom ( 1 H). Molecular structure analysis result showed that DEPT FT-NMR measurement mode with coupling as well as without coupling from 1 H was very fast, exact and accurate method for molecular analysis of organic compound especially methacryloyl-L-alanine methyl ester. (author)

Biodiesel production from crude cottonseed oil: an optimization process using response surface methodology

Energy Technology Data Exchange (ETDEWEB)

Fan, Xiaohu; Wang, Xi; Chen, Feng

2011-07-01

As the depletion of fossil resources continues, the demand for environmentally friendly sources of energy as biodiesel is increasing. Biodiesel is the resulting fatty acid methyl ester (FAME) from an esterification reaction. The use of cottonseed oil to produce biodiesel has been investigated in recent years, but it is difficult to find the optimal conditions of this process since multiple factors are involved. The aim of this study was to optimize the transesterification of cottonseed oil with methanol to produce biodiesel. A response surface methodology (RSM), an experimental method to seek optimal conditions for a multivariable system and reverse phase HPLC was used to analyze the conversion of triglyceride into biodiesel. RSM was successfully applied and the optimal condition was found with a 97% yield.

An Investigation of Anaerobic Processes in Fuel/Natural Seawater Environments

Science.gov (United States)

2012-02-08

separated esters and glycerin. Biodiesel contains no sulfur. In the United States the term "biodiesel" is standardized as fatty acid methyl ester ( FAME ...crude oil remaining. Biodiesel is produced from vegetable oils by converting the triglyceride oils to methyl (or ethyl) esters with a process known...water from the environment. Microbial growth in seawater can be limited by nutrients, including carbon. Biodiesel methyl esters are quite sparingly

Production of additives from Jatropha Curcas L. methyl esther as a way to improve diesel engine performance

Energy Technology Data Exchange (ETDEWEB)

Silitonga, A.S. [Department of Mechanical Engineering, Medan State Polytechnic (Indonesia)], email: ardinsu@yahoo.co.id, email: a_atabani2@msn.com; Mahlia, T.M.I. [Department of Mechanical Engineering, Syiah Kuala University, (Indonesia); Masjuki, H.H. [Department of Mechanical Engineering, University of Malaya (Malaysia); Ghofur, A. [Department of Mechanical Engineering, Lambung Mangkurat University (Indonesia); Abdullahe [Department of Chemical Engineering, Lambung Mangkurat University (Indonesia)

2011-07-01

Nowadays we are searching for ideal alternative fuels in order to reduce harmful gas emissions and improve air quality. And many kinds of bio-diesel have been proposed. This paper introduces a bio-diesel converted from the oil of Jatropha curcas L. through a series of physical and chemical processes. This bio-diesel, which has a high cetane number, is better adapted than diesel or other, edible, vegetable oils to be an ideal alternative fuel. Moreover, the additive promotes the physico-chemical characteristics of Jatropha curcas methyl ester, further enhancing its desirability as a substitute for diesel oil. This paper analyzes and reports the results of a laboratory-scale investigation of the feasibility of blending diesel with an additive produced from Jatropha curcas methyl ester. It finds that this additive can improve engine performance and reduce exhaust emissions.

Response surface methodology optimization of lipase catalyzed transesterification of Jatropha curcas L. seed oil for biodiesel production

International Nuclear Information System (INIS)

Li, Yingxia; Wang, Yun; Guan, Xiu Li; Yu, Dong Dong

2013-01-01

The immobilized lipase-catalyzed transesterification of Jatropha curcas L. seed oil and methanol for biodiesel production in tert-butanol was investigated. The effects of different tert-butanol volume, methanol molar ratio, reaction temperature, reaction time and immobilized lipase amount on the total conversion were systematically analyzed by response surface methodology (RSM). RSM analysis showed good correspondence between experimental and predicted values. The optimal conditions for the transesterification were a reaction time of 17.355 h, a reaction temperature of 34.868 °C, an immobilized lipase amount of 12.435 %, a methanol molar ratio of 5.282:1, a tert-butanol volume ratio of 0.577:1. The optimal predicted yield of fatty acid methyl esters (FAME) was 88.5 % and the actual value was 88.1 %. The predicted yield of fatty acid esters and the real one was very close, indicating that the RSM based on central composite design (CCD) was adaptable for a FAME study for the present transesterification system. Moreover, the infrared spectrum of biodiesel showed the characteristic bands of C=O, O–C–O, C=C and –(CH_2)n–. Furthermore, GC-linked mass spectrometry showed that biodiesel was mainly composed of the methyl esters of hexadecanoic, 9,12-octadecadienoic and 9-octadecadienoic acid

Utilização de argilas para purificação de biodiesel

Directory of Open Access Journals (Sweden)

Andréia Juliana Almeida de Paula

2011-01-01

Full Text Available This work describes the results of the purification of methyl biodiesel, obtained by oxidized soybean oil, using different methods. After the ester separation from the glycerin by decanting, the ester was purified each time with distillation, washing with water and adsorption with bauxite, bentonite and attapulgite. The removal of total contamination, unsaponifiable material, concentrations of free glycerin and soap were analyzed in the purified ester phase. The best result of purification was observed with the use of bentonite and bauxite, in the removal of soap and free glycerin respectively.

Fatty acid methyl esters production: chemical process variables

Directory of Open Access Journals (Sweden)

Paulo César Narváez Rincón

2004-05-01

Full Text Available The advantages of fatty acid methyl esters as basic oleochemicals over fatty acids, the seventies world energy crisis and the use of those oleochemicals as fuels, have increased research interest on fats and oils trans-esterification. In this document, a review about basic aspects, uses, process variables and problems associated to the production process of fatty acid methyl esters is presented. A global view of recent researches, most of them focused in finding a new catalyst with same activity as the alcohol-soluble hydroxides (NaOH, KOH, and suitable to be used in transforming fats and oils with high levels of free fatty acids and water avoiding separation problems and reducing process costs, is also discussed.

Cu2+ Montmorillonite K10 Clay Catalyst as a Green Catalyst for Production of Stearic Acid Methyl Ester: Optimization Using Response Surface Methodology (RSM

Directory of Open Access Journals (Sweden)

Enas A. Almadani

2018-01-01

Full Text Available Clay catalyst has received much attention to replace the homogeneous catalysts in the esterification reaction to produce fatty acid methyl ester as the source of biodiesel as it is low cost, easily available, as well as environmental friendly. However, the use of unmodified clay, in particular montmorillonite K10 (MMT K10, for the esterification of fatty acids showed that the acid conversion was less than 60% and this is not preferable to the production of biodiesel. In this study, synthesis of stearic acid methyl ester using Cu2+-MMT K10 (Cu-MMT K10 was successfully optimized via response surface methodo-logy (RSM based on 3-variable of Box-Behnken design (BB. The parameters were; reaction time (5-180 minutes, reaction temperature (80-120 oC and concentration of Cu2+ in MMT K10 (0.25-1 M. The use of RSM in optimizing the conversion of stearic acid was successfully developed as the actual experimental conversion of stearic acid was found similar to the actual values under the optimum conditions. The model equation predicted that the following conditions would generate the maximum conversion of stearic acid (87.05 %reaction time of 62 minutes, a reaction temperature of 80 oC and catalyst used is 1.0 M Cu-MMT K10. This finding can be considered as green catalytic process as it worked at moderate reaction temperature using low cost clay catalyst with a short reaction time. Copyright © 2018 BCREC Group. All rights reserved Received: 26th July 2017; Revised: 13rd January 2018; Accepted: 13rd January 2018; Available online: 22nd January 2018; Published regularly: 2nd April 2018 How to Cite: Almadani, E.A., Harun, F.W., Radzi, S.M., Muhamad, S.K. (2018. Cu2+ Montmorillonite K10 Clay Catalyst as a Green Catalyst for Production of Stearic Acid Methyl Ester: Optimization Using Response Surface Methodology (RSM. Bulletin of Chemical Reaction Engineering & Catalysis, 13 (1: 187-195 (doi:10.9767/bcrec.13.1.1397.187-195

Microbial degradation of palm (Elaeis guineensis biodiesel

Directory of Open Access Journals (Sweden)

Giselle Lutz

2006-03-01

Full Text Available The kinetics of biodegradation of palm-derived fatty methyl and ethyl esters (Elaeis guineensis biodiesel by a wild-type aerobic bacterial population was measured at 20 °C, as the rate of oxygen uptake by a manometric technique. The methyl and ethyl biodiesels were obtained by potassium-hydroxide catalysed transesterification of palm oil, respectively. The bacterial flora included the genera Bacillus, Proteus, Pseudomonas, Citrobacter and Enterobacter. The rate of oxygen uptake for palm biodiesel is similar to the quantity observed in the biodegradation of 1.0 mM solutions of simple substrates such as carbohydrates or amino acids.Palm methyl or ethyl biodiesel is subjected to facile aerobic biodegradation by wild-type bacteria commonly present in natural open environments. This result should lessen any environmental concern for its use as alternative fuel, solvent or lubricant. Rev. Biol. Trop. 54(1: 59-63.Epub 2006 Mar 31.La cinética de la biodegradación de los ésteres metílicos y etílicos derivados de palma (biodiesel por una población silvestre de bacterias aeróbicas fue medida a 20 °C, como medición manométrica del consumo de oxígeno. Los ésteres metílicos y etílicos se obtuvieron por transesterificación del aceite de palma con metanol y etanol,respectivamente. La flora bacteriana incluyó a los géneros Bacillus, Proteus, Pseudomonas, Citrobacter y Enterobacter. Las velocidades de consumo de oxígeno para las muestras de biodiesel fueron similares a lo observado en la biodegradación de disoluciones 1.0 mM de sustratos sencillos solubles en agua, tales como carbohidratos, aminoácidos y albúmina de huevo.

Design and optimisation of purification procedure for biodiesel washing

Directory of Open Access Journals (Sweden)

S.B. Glišić

2009-09-01

Full Text Available Almost complete methanolysis of triglycerides is usually not enough to fulfil the strict standards of biodiesel quality. A key step in this process is neutralization of alkali (catalyst followed by the washing procedure necessary for removing different impurities such as traces of catalyst and methanol and removal of soaps and glycerol from esters phase. The washing with hot water is still widely used in many industrial units for the biodiesel production. In this study, different procedures of biodiesel washing using hot water were investigated. The orto-phosphoric acid was suggested as the best compound for alkali catalyst (sodium hydroxide neutralization. The main goal of the performed analysis was to minimize the water usage in the washing-neutralization step during the biodiesel production. Such solution would make the process of biodiesel synthesis more economical taking into account the decrease of energy consumed for evaporation of water during the final product purification, as well as more acceptable procedure related to the impact on environment (minimal waste water release. Results of the performed simulation of the washing process supported by original experimental data suggested that neutralization after the optimized washing process of the methyl ester layer could be the best solution. The proposed washing procedure significantly decreases the amount of waste water giving at the same time the desired purity of final products (biodiesel and glycerol. The simulation of the process was performed using ASPEN plus software supported by ELCANTREL and UNIQUAC procedure of required properties calculation

Prospects of Tectona Grandis as a Feedstock for Biodiesel

International Nuclear Information System (INIS)

Sarin, Amit; Singh, Meetu; Sharma, Neerja; Singh, N. P.

2017-01-01

The limited availability of fossil fuels has encouraged the need of replacement fuels of renewable nature. Among the renewable fuels, biodiesel produced from oil seeds and food wastes has been favored by the majority of researchers. In this study, Tectona Grandis seed oil has been investigated as a non-edible feedstock for biodiesel. The oil content of seed is 43% which makes it suitable for commercial production of biodiesel. The synthesis of biodiesel from T. Grandis oil was done with transesterification reaction giving high percentage yield of biodiesel which reached to 89%. The T. Grandis biodiesel was subjected to determine various physicochemical parameters by standard testing methods and found in agreement with the ASTM D-6751 and EN-14214 standards. The fatty-acid methyl ester composition for the biodiesel is composed of 42.71% oleic acid, 13.1% palmitic acid, and 31.51% linoleic acid. The biodiesel showed low oxidation stability which is attributed to high percentage of unsaturation. To address this issue, synthetic antioxidants were added to increase its resistance towards oxidation. By considering all the parameters, the present study reveals that T. Grandis seed oil is reliable for the production of biodiesel with encouraging probability in future.

Prospects of Tectona Grandis as a Feedstock for Biodiesel

Energy Technology Data Exchange (ETDEWEB)

Sarin, Amit, E-mail: amit.sarin@yahoo.com [Department of Physical Sciences, I.K. Gujral Punjab Technical University, Kapurthala (India); Singh, Meetu [Department of Applied Sciences, I.K. Gujral Punjab Technical University, Kapurthala (India); Sharma, Neerja [PG Department of Physics and Electronics, DAV College, Amritsar (India); Singh, N. P. [Department of Planning and External Development, I.K. Gujral Punjab Technical University, Kapurthala (India)

2017-10-26

The limited availability of fossil fuels has encouraged the need of replacement fuels of renewable nature. Among the renewable fuels, biodiesel produced from oil seeds and food wastes has been favored by the majority of researchers. In this study, Tectona Grandis seed oil has been investigated as a non-edible feedstock for biodiesel. The oil content of seed is 43% which makes it suitable for commercial production of biodiesel. The synthesis of biodiesel from T. Grandis oil was done with transesterification reaction giving high percentage yield of biodiesel which reached to 89%. The T. Grandis biodiesel was subjected to determine various physicochemical parameters by standard testing methods and found in agreement with the ASTM D-6751 and EN-14214 standards. The fatty-acid methyl ester composition for the biodiesel is composed of 42.71% oleic acid, 13.1% palmitic acid, and 31.51% linoleic acid. The biodiesel showed low oxidation stability which is attributed to high percentage of unsaturation. To address this issue, synthetic antioxidants were added to increase its resistance towards oxidation. By considering all the parameters, the present study reveals that T. Grandis seed oil is reliable for the production of biodiesel with encouraging probability in future.

CFD simulation of fatty acid methyl ester production in bubble column reactor

Science.gov (United States)

Salleh, N. S. Mohd; Nasir, N. F.

2017-09-01

Non-catalytic transesterification is one of the method that was used to produce the fatty acid methyl ester (FAME) by blowing superheated methanol bubbles continuously into the vegetable oil without using any catalyst. This research aimed to simulate the production of FAME from palm oil in a bubble column reactor. Computational Fluid Dynamic (CFD) simulation was used to predict the distribution of fatty acid methyl ester and other product in the reactor. The fluid flow and component of concentration along the reaction time was investigated and the effects of reaction temperature (523 K and 563 K) on the non-catalytic transesterification process has been examined. The study was carried out using ANSYS CFX 17.1. The finding from the study shows that increasing the temperature leads to higher amount of fatty acid methyl ester can be produced in shorter time. On the other hand, concentration of the component such as triglyceride (TG), glycerol (GL) and fatty acid methyl ester (FAME) can be known when reaching the optimum condition.

Comparison of performance of biodiesels of mahua oil and gingili oil in dual fuel engine

Directory of Open Access Journals (Sweden)

Nadar Kapilan N.

2008-01-01

Full Text Available In this work, an experimental work was carried out to compare the performance of biodiesels made from non edible mahua oil and edible gingili oil in dual fuel engine. A single cylinder diesel engine was modified to work in dual fuel mode and liquefied petroleum gas was used as primary fuel. Biodiesel was prepared by transesterification process and mahua oil methyl ester (MOME and gingili oil methyl ester (GOME were used as pilot fuels. The viscosity of MOME is slightly higher than GOME. The dual fuel engine runs smoothly with MOME and GOME. The test results show that the performance of the MOME is close to GOME, at the pilot fuel quantity of 0.45 kg/h and at the advanced injection timing of 30 deg bTDC. Also it is observed that the smoke, carbon monoxide and unburnt hydro carbon emissions of GOME lower than the MOME. But the GOME results in slightly higher NOx emissions. From the experimental results it is concluded that the biodiesel made from mahua oil can be used as a substitute for diesel in dual fuel engine.

Adjusting the operating characteristics to improve the performance of an emulsified palm oil methyl ester run diesel engine

International Nuclear Information System (INIS)

Debnath, Biplab K.; Sahoo, Niranjan; Saha, Ujjwal K.

2013-01-01

Highlights: ► The oxygenated biodiesel has a lower calorific value and emits higher NO X than diesel. ► The objective is to study the water in palm oil biodiesel emulsion in a diesel engine. ► The tests are performed at higher compression ratio and retarded injection timing. ► The results obtained are compared with a POME run diesel engine. ► Higher efficiency, lower ignition delay and emissions are the outcomes. - Abstract: The popularity of emulsified fuels as alternative to diesel is cumulative. The water in diesel emulsion is the most practiced one. The presence of water in emulsion and its micro-explosion reduces emissions. However, the emulsified biodiesel is not properly explored. The reason may be due to its lesser calorific value that does not augment efficiency. Alongside oxygenated biodiesel generally emits higher NO X than diesel. Therefore, the present investigation targets at finding the performance, combustion and emission characteristics of emulsified biodiesel in a diesel engine at an elevated compression ratio (CR) and retarded injection timing (IT). This is because; at this CR–IT combination emulsified fuel will be injected at the warmer environment, mechanically created inside the cylinder. The objective is to achieve a faster combustion, lower ignition delay (ID), improved performance and emission characteristics. The biodiesel used in this work is the palm oil methyl ester (POME). The prepared two-phase water in POME (WIP) emulsion is tested in a variable compression ratio (VCR) diesel engine at CR = 18 and IT = 20°BTDC. The results obtained are then compared with the POME run engine data under the same CR and IT specifications. Additionally, experiments have also been conducted in the same engine at CR = 17.5 and IT = 23°BTDC to compare its results with those of WIP and POME run engines

Microalgal fatty acid methyl ester a new source of bioactive compounds with antimicrobial activity

Directory of Open Access Journals (Sweden)

Arumugham Suresh

2014-09-01

Full Text Available Objective: To evaluate fatty acid composition and the antimicrobial activity of the major fraction of fatty acid methyl ester (FAME extracts from three microalgae collected from freshwater lakes in Theni District, Tamil Nadu, India. Methods: Antimicrobial study was carried out by well diffusion method against bacterial as well as fungal pathogens such as Escherichia coli, Staphylococcus aureus, Enterobacter sp., Klebsiella sp., Salmonella typhi, Fusarium sp., Cryptococcus sp., Candida sp., and Aspergillus niger and Aspergillus flavus. The FAME profiles were determined through gas chromatography with a flame ionization detector. Results: The FAME was found to be radial effective in inhibiting the radial growth of both bacterial and fungal pathogens. The FAME extracts exhibited the antibacterial activity against three clinical pathogens, namely, Escherichia coli, Salmonella typhi and Enterobacter sp. with the maximum zone of inhibition of 12.0 mm, 12.0 mm and 11.0 mm, respectively. The FAME showed moderate antifungal activity against Cryptococcus sp. (11.8 mm, Aspergillus niger (10.5 mm, Candida sp. (11.8 mm and Fusarium sp. (10.4 mm. Gas chromatography-flame ionization detector analysis revealed about 30 different FAMEs. Conclusions: We assume that the observed antimicrobial potency may be due to the abundance of erucic acid methyl ester (C22:0, arachidic acid methyl ester (C20:0, palmitic acid methyl ester (C16:0, cis-11-eicosenoicmethyl ester (C20:1, cis-11, 14-eicosadienoic acid methyl ester (C20:2 and linolenic acid methyl ester (C18:3 in FAMEs which appears to be promising to treat microbial diseases.

The uses of biodiesel in buses

International Nuclear Information System (INIS)

Smigins, R.; Gulbis, V.

2003-01-01

In November 2001 in Naukseni, Valmiera district the biodiesel - methyl ester of rapeseed oil (RME) - plant first in Latvia and in all Baltic States began to work. The production capacity of the plant is 2500 t of biodiesel per year. In the summer and autumn period of the last year the first experiment using 100% RME on one city bus line was carried out. The bus Ikarus-280 in total turned 30700 km consuming 11 tons or 12600 litres of biodiesel. The fuel consumption with biodiesel was 0.9 kg/h (14.2%) or 3.01/100 km higher as with fossil diesel fuel. The engine power and the driving speed on the line were practically unchanged in spite that the heat capacity of biodiesel is lower than of ordinary diesel fuel (according 37.1 l and 42.1 MJ/kg). Using biodiesel the toxicity of the exhaust gases dropped down very essentially. It was controlled regularly by measuring the absorption coefficient and smokiness. At the end of second month of the experiment the absorption coefficient was 2.09 m -1 and 47.8%. This shows that by the influence of biodiesel the compression chambers of the engine clean from burnt parts and the combustion process most completely thanks to the oxygen content in the biodiesel (authors)

Gelatin films plasticized with a simulated biodiesel coproduct stream

Directory of Open Access Journals (Sweden)

2009-04-01

Full Text Available In order to explore the possibility of substituting an unrefined biodiesel coproduct stream (BCS for refined glycerol as a polymer plasticizer we have prepared cast gelatin films plasticized with a simulated BCS, i.e., mixtures of glycerol and some of the typical components found in BCS (methyl linoleate, methyl oleate, linoleic acid, and oleic acid. We measured the tensile properties as a function of plasticizer composition, and analyzed the specific effect of each individual component on tensile properties. We found that it is the unrecovered alkyl esters that largely determine the tensile properties, and that BCS can be successfully used to plasticize cast gelatin films as long as the BCS contains 11 parts by weight, or less, of unrecovered alkyl esters per 100 parts glycerol.

Transesterification for the preparation of biodiesel from crude-oil of Pongamia pinnata

Directory of Open Access Journals (Sweden)

Babu Veeresh A.

2009-01-01

Full Text Available Biodiesel was prepared from the non-edible oil of Pongamia pinnata L. by transesterification of the crude-oil with methanol in the presence of NAOH as catalyst. Vegetable oils can be transesterified by heating them with a large excess of anhydrous methanol and an acidic or basic reagent as catalyst. Both the acid as well as alkaline esterifications were subsequently performed to get the final product. A catalyst is usually used to improve the reaction rate and yield. NaOH was found to be a better catalyst than KOH in terms of yield. In a transesterification reaction, a larger amount of methanol was used to shift the reaction equilibrium to the right side and produce more methyl esters as the proposed product. Several aspects including the type of catalyst (alkaline, acid, or enzyme, alcohol/vegetable oil molar ratio, temperature, purity of the reactants (mainly water content and free fatty acid content have an influence on the course of the transesterification. A maximum conversion of 94% (oil to ester was achieved using a 1:10 molar ratio of oil to methanol at 60 to 65 °C. Important fuel properties of methyl esters of pongamia oil (biodiesel compare well with ASTM standards.

Optimization of biodiesel production in a hydrodynamic cavitation reactor using used frying oil.

Science.gov (United States)

Ghayal, Dyneshwar; Pandit, Aniruddha B; Rathod, Virendra K

2013-01-01

The present work demonstrates the application of a hydrodynamic cavitation reactor for the synthesis of biodiesel with used frying oil as a feedstock. The synthesis involved the transesterification of used frying oil (UFO) with methanol in the presence of potassium hydroxide as a catalyst. The effect of geometry and upstream pressure of a cavitating orifice plate on the rate of transesterification reaction has been studied. It is observed that the micro level turbulence created by hydrodynamic cavitation somewhat overcomes the mass transfer limitations for triphasic transesterification reaction. The significant effects of upstream pressure on the rate of formation of methyl esters have been seen. It has been observed that flow geometry of orifice plate plays a crucial role in process intensification. With an optimized plate geometry of 2mm hole diameter and 25 holes, more than 95% of triglycerides have been converted to methyl esters in 10 min of reaction time with cavitational yield of 1.28 × 10(-3) (Grams of methyl esters produced per Joule of energy supplied). The potential of UFO to produce good quality methyl esters has been demonstrated. Copyright © 2012 Elsevier B.V. All rights reserved.

Experimental analysis on thermally coated diesel engine with neem oil methyl ester and its blends

Science.gov (United States)

Karthickeyan, V.

2018-01-01

Depletion of fossil fuel has created a threat to the nation's energy policy, which in turn led to the development of new source renewable of energy. Biodiesel was considered as the most promising alternative to the traditional fossil fuel. In the present study, raw neem oil was considered as a principle source for the production of biodiesel and converted into Neem Oil Methyl Ester (NOME) using two stage transesterification process. The chemical compositions of NOME was analysed using Fourier Transform Infra-Red Spectroscopy (FTIR) and Gas Chromatography- Mass Spectrometry (GC-MS). Baseline readings were recorded with diesel, 25NOME (25% NOME with 75% diesel) and 50NOME (50% NOME with 50% diesel) in a direct injection, four stroke, water cooled diesel engine. Thermal Barrier Coating (TBC) was considered as a better technique for emission reduction in direct injection diesel engine. In the present study, Partially Stabilized Zirconia (PSZ) was used as a TBC material to coat the combustion chamber components like cylinder head, piston head and intake and exhaust valves. In coated engine, 25NOME showed better brake thermal efficiency and declined brake specific fuel consumption than 50NOME. Decreased exhaust emissions like CO, HC and smoke were observed with 25NOME in coated engine except NOx. [Figure not available: see fulltext.

A study on the production of biodiesel from used frying oil

International Nuclear Information System (INIS)

Abbasi, M.; Ali, A.S.; Farhan, M.; Shabbir, S.A.

2013-01-01

The study was carried out to utilize waste frying oil for biodiesel production because it is cheap, easily available and renewable raw material. The used frying oil was analysed for water contents (0.43%) iodine value (52), sponification value (205), free fatty acids 8.7 (Xo) and acid value (0.8 mg KOH/g). Esterification and transesterification were conducted to convert free Fatty acids and triglycerides to methyl ester (biodiesel), respectively. One-step and two-step transertification reactions were carried out to measure the efficiency of these processes for biodiesel production. The biodiesel produced from used frying oil was examined for flash point (185 degree C) kinematic viscosity (4.86 mm/sup 2/s) and specific gravity (0.884 g/mL) that were meeting the limits of ASTM and Thai standards. Hence, it was proved to be a useful technique for biodiesel production at commercial scale. (author)

Combustion Chemistry of Biodiesel for the Use in Urban Transport Buses: Experiment and Modeling

Science.gov (United States)

Omidvarborna, Hamid

Biofuels, such as biodiesel, offer benefits as a possible alternative to conventional fuels due to their fuel source sustainability and their reduced environmental impact. Before they can be used, it is essential to understand their combustion chemistry and emission characterizations due to a number of issues associated with them (e.g., high emission of nitrogen oxides (NOx), lower heating value than diesel, etc.). During this study, emission characterizations of different biodiesel blends (B0, B20, B50, and B100) were measured on three different feedstocks (soybean methyl ester (SME), tallow oil (TO), and waste cooking oil (WCO)) with various characteristics, while an ultra-low sulfur diesel (ULSD) was used as base fuel at low-temperature combustion (LTC). A laboratory combustion chamber was used to analyze soot formation, NOx emissions, while real engine emissions were measured for further investigation on PM and NOx emissions. For further study, carbon emissions (CO, CO 2, and CH4) were also measured to understand their relations with feedstocks' type. The emissions were correlated with fuel's characteristics, especially unsaturation degree (number of double bonds in methyl esters) and chain length (oxygen-to-carbon ratio). The experimental results obtained from laboratory experiments were confirmed by field experiments (real engines) collected from Toledo area regional transit authority (TARTA) buses. Combustion analysis results showed that the neat biodiesel fuels had longer ignition delays and lower ignition temperatures compared to ULSD at the tested condition. The results showed that biodiesel containing more unsaturated fatty acids emitted higher levels of NOx compared to biodiesel with more saturated fatty acids. A paired t-test on fuels showed that neat biodiesel fuels had significant reduction in the formation of NOx compared with ULSD. In another part of this study, biodiesel fuel with a high degree of unsaturation and high portion of long chains of

The Current Status of Biodiesel Production Technology: A Review

Directory of Open Access Journals (Sweden)

Rizal Alamsyah

2007-12-01

Full Text Available Biodiesel is addressed to the name of fuel which consist of mono-alkyl ester that made from renewable and biodegradable resources, such as oils from plants (vegetable oils, waste or used cooking oil, and animal fats. Such oils or fats are chemically reacted with alcohols or methanol In producing chernical compounds called fatty acid methyl ester (FAME and these reactions are called transesterification and esterification. Glycerol, used in the pharmaceutical and cosmetics industry is produced from biodiesel production as a by-product. Researches on biodiesel as an alternative petroleum diesel have been done for more than 20 years. Transesterification reaction can be acid-catalyzed, alkali-catatyzed, or enzyme-catalyzed. Commercially biodiesel is processed by transesterification with alkali catalyst. This process, however, requires refining of products and recovery of catalysts, Such biodiesel production accelerates researches on biodiesel to obtain simpler methods, better quality. and minimum production cost. Besides the catalytic production for biodiesel, there is a method for biodiesel production namely non-catalytic production. Non-catalytic transesterification method was developed since catalytic tranestertfification still has two main problems assoclated With long reaction time and complicated purification. The first problem occurres because of the two phase nature of vegetable oil/methanol mixture, and the last problem is due to purification of catalyst and glycerol. The application of catalytic tranestertfication method leads to condition of high biodiesel production cost and high energy consumption. This paper provides information of biodiesel production progress namely catalytic tranestertfification (acid, alkali, and enzymatic tranesterfification, and non-catalytic tranesterification (at sub-critical­-supercritical temperature under pressurized conditions. It was found that every method of biodiesel production still has advantages and

Experimental and analytical investigation on the emission and combustion characteristics of CI engine fueled with tamanu oil methyl esters

Directory of Open Access Journals (Sweden)

Perumal Navaneetha Krishnan

2016-01-01

Full Text Available The emission and combustion characteristics of a four stroke multi fuel single cylinder variable compression ratio engine fueled with tamanu oil methyl ester and its blends 10%, 20%, 40%, and 60% with diesel (on volume basis are examined and compared with standard diesel. Biodiesel produced from tamanu oil by trans-esterification process has been used in this study. The experiment has been conducted at a constant engine speed of 1500 rpm with 50% load and at compression ratios of 16:1, 17:1, 18:1, 19:1, and 20:1. With different blend and for selected compression ratio the exhaust gas emissions such as CO, HC, NOx, CO2, and the combustion characteristics are measured. The variation of the emission parameters for different compression ratios and for different blends is given, and optimum compression ratio which gives best performance has been identified. The results indicate higher rate of pressure rise and minimum heat release rate at higher compression ratio for tamanu oil methyl ester when compared with standard diesel. The blend B40 for tamanu oil methyl ester is found to give minimum emission at 50% load. The blend when used as fuel results in reduction of polluting gases like HC, CO, and increase in NOx emissions. The previously mentioned emission parameters have been validated with the aid of artificial neural network. A separate model is developed for emission characteristics in which compression ratio, blend percentage and load percentage were used as the input parameter whereas CO, CO2, HC, and NOx were used as the output parameter. This study shows that there is a good correlation between the artificial neural network predicted values and the experimental data for different emission parameters.

Efficacy of specific gravity as a tool for prediction of biodiesel-petroleum diesel blend ratio

Science.gov (United States)

Prediction of volumetric biodiesel/petrodiesel blend ratio (VBD) from specific gravity (SG) data was the subject of the current investigation. Fatty acid methyl esters obtained from soybean, palm, and rapeseed oils along with chicken fat (SME-1, SME-2, PME, RME, and CFME) were blended (0 to 20 volum...

ESolvent-free, enzyme-catalyzed biodiesel production from mango, neem, and shea oils via response surface methodology

OpenAIRE

Nde, Divine Bup; Astete, Carlos; Boldor, Dorin

2015-01-01

Mango, neem and shea kernels produce non-conventional oils whose potentials are not fully exploited. To give an added value to these oils, they were transesterified into biodiesel in a solvent-free system using immobilized enzyme lipozyme from Mucor miehei. The Doehlert experimental design was used to evaluate the methyl ester (ME) yields as influenced by enzyme concentration?EC, temperature?T, added water content?AWC, and reaction time?RT. Biodiesel yields were quantified by 1H NMR spectrosc...

Phase behaviour measurements for the system (carbon dioxide + biodiesel + ethanol) at high pressures

International Nuclear Information System (INIS)

Araújo, Odilon A.S.; Silva, Fabiano R.; Ramos, Luiz P.; Lenzi, Marcelo K.; Ndiaye, Papa M.; Corazza, Marcos L.

2012-01-01

Graphical abstract: Comparison between ethyl and methyl esters in a pressure-composition of {CO 2 (1) + biodiesel(2)} at 303.15 K (triangles), 323.15 K (squares) and 343.15 K (circles). Open symbols are ethyl biodiesel (this work) and closed symbols are methyl biodiesel data by Pinto et al. Highlights: ► We measured phase behaviour for the system involving {CO 2 + biodiesel + ethanol}. ► The saturation pressures were obtained using a variable-volume view cell. ► The experimental data were modelled using PR-vdW2 and PR-WS equations of state. - Abstract: This work reports phase equilibrium measurements for binary system {CO 2 (1) + biodiesel(2)} and ternary system {CO 2 (1) + biodiesel(2) + ethanol(3)}. The biodiesel (ethyl esters) used in this work was produced from soybean oil, purified and characterised following the standard specification for subsequent use. Nowadays, great interest in biodiesel production processes at supercritical and/or pressurised solvents is observed, such as, non-catalytic supercritical biodiesel production and enzyme-catalyzed biodiesel production, besides the supercritical CO 2 can be an interesting alternative to glycerol separation in the biodiesel purification step. Towards this, the main goal of this work is to study the phase behaviour at high pressure for the binary and ternary systems involving CO 2 , biodiesel and ethanol. Experiments were carried out in a high pressure variable-volume view cell with operating temperatures ranging from (303.15 to 343.15) K and pressures up to 25 MPa. The CO 2 molar fraction ranged from 0.4213 to 0.9855 for the system {CO 2 (1) + biodiesel(2)}, 0.4263 to 0.9781 for the system {CO 2 (1) + biodiesel(2) + ethanol(3)} with a biodiesel to ethanol molar ratio of (1:3), and 0.4317 to 0.9787 for the system {CO 2 (1) + biodiesel(2) + ethanol(3)} with a biodiesel to ethanol molar ratio of (1:8). For the systems investigated, vapour–liquid (VL), liquid–liquid (LL) and vapour–liquid–liquid (VLL

Experimental studies on the combustion and emission characteristics of a diesel engine fuelled with used cooking oil methyl ester and its diesel blends

Energy Technology Data Exchange (ETDEWEB)

Lakshmi Narayana Rao, G.; Sampath, S. [Sri Venkateswara College of Engineering, Sriperumbudur (India); Rajagopal, K. [Jawaharlal Nehru Technological Univ., Hyderabad (India)

2008-04-01

Transesterified vegetable oils (biodiesel) are promising alternative fuel for diesel engines. Used vegetable oils are disposed from restaurants in large quantities. But higher viscosity restricts their direct use in diesel engines. In this study, used cooking oil was dehydrated and then transesterified using an alkaline catalyst. The combustion, performance and emission characteristics of Used Cooking oil Methyl Ester (UCME) and its blends with diesel oil are analyzed in a direct injection C.I. engine. The fuel properties and the combustion characteristics of UCME are found to be similar to those of diesel. A minor decrease in thermal efficiency with significant improvement in reduction of particulates, carbon monoxide and unburnt hydrocarbons is observed compared to diesel. The use of transesterified used cooking oil and its blends as fuel for diesel engines will reduce dependence on fossil fuels and also decrease considerably the environmental pollution. Of the various alternate fuels under consideration, biodiesel is the most promising due to the following reasons: (1) Biodiesel can be used in the existing engine without any modifications. (2) Biodiesel is made entirely from vegetable sources; it does not contain any sulfur, aromatic hydrocarbons, metals or crude oil residues. (3) Biodiesel is an oxygenated fuel; emissions of carbon monoxide and soot tend to reduce. (4) Unlike fossil fuels, the use of biodiesel does not contribute to global warming as CO{sub 2} emitted is once again absorbed by the plants grown for vegetable oil/biodiesel production. Thus CO{sub 2} balance is maintained. (5) The Occupational Safety and Health Administration classifies biodiesel as a non-flammable liquid. (6) The use of biodiesel can extend the life of diesel engines because it is more lubricating than petroleum diesel fuel. (7) Biodiesel is produced from renewable vegetable oils/animal fats and hence improves the fuel or energy security and economy independence.

A comparative estimation of C.I. engine fuelled with methyl esters of punnai, neem and waste cooking oil

Energy Technology Data Exchange (ETDEWEB)

Subramaniam, D.; Avinash, A. [Department of Mechanical Engineering - K.S.Rangasamy College of Technology –Tiruchengode, 637215 Tamil Nadu (India); Murugesan, A. [Department of Mechatronics Engineering - K.S.Rangasamy College of Technology – Tiruchengode, 637215 Tamil Nadu (India)

2013-07-01

In this experimental study, performance, emission, and combustion characteristics of methyl esters of Punnai, Neem, Waste Cooking Oil and their diesel blends in a C.I. engine was experimentally examined. For the study, Punnai oil methyl esters (POME), neem oil methyl esters (NOME), and Waste Cooking Oil Methyl Esters (WCOME) were prepared by tranesterification process. The Bio diesel-diesel blends were prepared by mixing 10%, 30%, 50%, and 70% of bio diesel with diesel. The effects of three methyl esters and their diesel blends on engine performance, combustion, and exhaust emissions were examined at different engine loads. Experimental results concluded that up to 30% of methyl esters did not affect the performance, combustion, and emissions characteristics. On the other hand, above B30 (30% Bio diesel with 70% diesel) a reduction in performance, combustion, and emission characteristics were clear from the study.

Feasibility study of microalgal and jatropha biodiesel production plants: Exergy analysis approach

International Nuclear Information System (INIS)

Ofori-Boateng, Cynthia; Keat, Teong Lee; JitKang, Lim

2012-01-01

The exergy analyses performed in this study are based on three thermodynamic performance parameters namely exergy destruction, exergy efficiency and thermodynamic improvement potentials. After mathematical analysis with Aspen Plus software, the results showed that 64% and 44% of the total exergy content of the input resources into microalgal methyl ester (MME) and jatropha methyl ester (JME) production plants were destroyed respectively for 1 ton of biodiesel produced. This implies that only 36% and 56% (for MME and JME production plants respectively) useful energy in the products is available to do work. The highest and lowest exergy destructions were recorded in the oil extraction units (38% and 39% of the total exergy destroyed for MME and JME plants respectively) and transesterification units (5% and 2% of total exergy destroyed for MME and JME plants respectively) respectively for 1 ton biodiesel produced. Since sustainable biodiesel production depends on cultivation of feedstock, oil extraction and transesterification processes, exergy analysis which is carried out on only the transesterification unit cannot justify the thermodynamic feasibility of the whole biodiesel production plant unless a complete thermodynamic assessment has been done for the whole plant. Thus, according to this study which considers all the biodiesel production processes, MME and JME production plants are not thermodynamically feasible. - Highlights: ► 64% of exergy content of input resources into MME production plant is destroyed. ► 44% of exergy content of input resources into JME production plant is destroyed. ► Exergetic efficiencies of MME and JME production plants are far less than 1. ► Thermodynamically, MME and JME production plants are unsustainable. ► Exergy loss can be reduced by using heat integrated reactive distillation process.

Branched-chain fatty acid methyl esters as cold flow improvers for biodiesel

Science.gov (United States)

Biodiesel is an alternative diesel fuel derived mainly from the transesterification of plant oils with methanol or ethanol. This fuel is generally made from commodity oils such as canola, palm, or soybean and has a number of properties that make it compatible in compression-ignition engines. Despite...

Thermophysical properties of biodiesel and related systems: Low-pressure vapor + liquid equilibrium of methyl/ethyl soybean biodiesel

International Nuclear Information System (INIS)

Veneral, Josamaique G.; Junior, Dirceu L.R.; Mazutti, Marcio A.; Voll, Fernando A.P.; Cardozo-Filho, Lúcio; Corazza, Marcos L.; Silva, Edson A.; Oliveira, J. Vladimir

2013-01-01

Highlights: • Boiling point temperatures for soybean FAME and FAEE measured in the pressure range of (6.7 to 66.7) kPa. • Investigated systems presented a non-ideal behavior, with positive deviations from Raoult’s law. • Experimental data satisfactorily represented by the UNIQUAC model. -- Abstract: In this work, experimental boiling point temperatures for pseudo-binaries (methyl/ethyl biodiesel + methanol/ethanol) and pseudo-ternaries (methyl/ethyl biodiesel + methanol/ethanol + glycerol/water) systems were measured at several pressures ranging from (6.7 to 66.7) kPa using an Othmer-type ebulliometer. The systems investigated show a non-ideal behavior, with positive deviations from Raoult’s law. It was observed that the addition of up to 10 wt% of alcohol (methanol or ethanol) led to a significant decrease in the boiling point temperature of the systems. The UNIQUAC model was successfully used to represent the experimental results, with an overall average deviation between experimental and calculated boiling temperature values of 0.004%

A process model to estimate the cost of industrial scale biodiesel production from waste cooking oil by supercritical transesterification

NARCIS (Netherlands)

Kasteren, van J.M.N.; Nisworo, A.P.

2007-01-01

This paper describes the conceptual design of a production process in which waste cooking oil is converted via supercritical transesterification with methanol to methyl esters (biodiesel). Since waste cooking oil contains water and free fatty acids, supercritical transesterification offers great

Production of Methyl Ester (Biodiesel from Used Cooking Oils via Trans-esterification process

Directory of Open Access Journals (Sweden)

Sameer Mohammed Salman

2016-06-01

Full Text Available Used cooking oil was undergoing trans-esterification reaction to produce biodiesel fuel. Method of production consisted of pretreatment steps, trans-esterification, separation, washing and drying. Trans-esterification of treated oils was studied at different operation conditions, the methanol to oil mole ratio were 6:1, 8:1, 10:1, and 12:1, at different temperature 30, 40, 50, and 60 º C, reaction time 40, 60, 80, and 120 minutes, amount of catalyst 0.5, 1, 1.5, and 2 wt.% based on oil and mixing speed 400 rpm. The maximum yield of biodiesel was 91.68 wt.% for treated oils obtained by trans-esterification reaction with 10:1 methanol to oil mole ratio, 60 º C reaction temperature, 80 minute reaction time and 0.5 wt.% of NaOH catalyst. The physical properties such as specific gravity, kinematic viscosity, acid number, flash point, pour point, and water content, were measured and compared them with American Standard Test Methods (ASTM D6751. The results of these properties for biodiesel product at (6:1, 8:1, 10:1, and 12:1 of methanol to oil mole ratio were within the range of American Standard Test Methods (ASTM D6751.

Measurement of Antioxidant Effects on the Auto-oxidation Kinetics of Methyl Oleate – Methyl Laurate Blend as a Surrogate Biodiesel System

Directory of Open Access Journals (Sweden)

Tjokorde Walmiki Samadhi

2017-05-01

Full Text Available This research investigates the feasibility of methyl oleate-methyl laurate blend as a surrogate biodiesel system which represents jatropha-coconut oil biodiesel, a potentially suitable formulation for tropical climate, to quantify the efficacy of antioxidant additives in terms of their kinetic parameters. This blend was tested by the Rancimat EN14112 standard method. The Rancimat tests results were used to determine the primary oxidation induction period (OIP and first-order rate constants and activation energies. Addition of BHT and EcotiveTM antioxidants reduces the rate constants (k, h-1 between 15 to 90% in the 50-200 ppm dose range, with EcotiveTM producing significantly lower k values. Higher dose reduces the rate constant, while oleate/laurate ratio produces no significant impact. Antioxidants increase the oxidation activation energy (Ea, kJ/mol by 180 to almost 400% relative to the non-antioxidant value of 27.0 kJ/mol. EcotiveTM exhibits lower Ea, implying that its higher efficacy stems from a better steric hindrance as apparent from its higher pre-exponential factors. The ability to quantify oxidation kinetic parameters is indicative of the usefulness of methyl oleate-laurate pure FAME blend as a biodiesel surrogate offering better measurement accuracy due to the absence of pre-existing antioxidants in the test samples. Copyright © 2017 BCREC GROUP. All rights reserved Received: 6th July 2016; Revised: 7th December 2016; Accepted: 30th January 2017 How to Cite: Samadhi, T.W., Hirotsu, T., Goto, S. (2017. Measurement of Antioxidant Effects on the Auto-oxidation Kinetics of Methyl Oleate-Methyl Laurate Blend as a Surrogate Biodiesel System. Bulletin of Chemical Reaction Engineering & Catalysis, 12 (2: 157-166 (doi:10.9767/bcrec.12.2.861.157-166 Permalink/DOI: http://dx.doi.org/10.9767/bcrec.12.2.861.157-166

High-yield production of biodiesel by non-catalytic supercritical methanol transesterification of crude castor oil (Ricinus communis)

International Nuclear Information System (INIS)

Román-Figueroa, Celián; Olivares-Carrillo, Pilar; Paneque, Manuel; Palacios-Nereo, Francisco Javier; Quesada-Medina, Joaquín

2016-01-01

The synthesis of biodiesel from crude castor oil in a catalyst-free process using supercritical methanol in a batch reactor was investigated, studying the evolution of intermediate products as well as the conversion of triglycerides and the yield of FAMEs (fatty acid methyl esters) (biodiesel). Experiments were carried out in a temperature range of 250–350 °C (10–43 MPa) at reaction times of 15–90 min for a methanol-to-oil molar ratio of 43:1. Maintaining thermal stability of biodiesel is one of the most important concerns in high-yield supercritical biodiesel production. Hence, thermal decomposition degree of FAMEs was also investigated in different reaction conditions. The maximum yield of FAMEs (96.5%) was obtained at 300 °C (21 MPa) and 90 min. Under these conditions, the conversion of triglycerides was complete, the yield of intermediate products was low (3.29 and 1.41% for monoglycerides and diglycerides, respectively), and thermal decomposition of FAMEs did not occur. The maximum degree of thermal decomposition (80.9%) was produced at 350 °C (43 MPa) and 90 min. Methyl ricinoleate, whose fatty acid chain was the most abundant (88.09 mol%) in castor oil, was very unstable above 300 °C and 60 min, leading to low yields of FAMEs under these conditions. - Highlights: • Supercritical synthesis of biodiesel from crude castor oil was investigated. • Supercritical methanolysis of crude castor oil reached a high yield of FAMEs. • Ricinoleic acid methyl ester was very unstable above 300 °C and 60 min reaction.

Biodiesel from sunflower oil in supercritical methanol with calcium oxide

International Nuclear Information System (INIS)

Demirbas, Ayhan

2007-01-01

In this study, sunflower seed oil was subjected to the transesterification reaction with calcium oxide (CaO) in supercritical methanol for obtaining biodiesel. Methanol is used most frequently as the alcohol in the transesterification process. Calcium oxide (CaO) can considerably improve the transesterification reaction of sunflower seed oil in supercritical methanol. The variables affecting the methyl ester yield during the transesterification reaction, such as the catalyst content, reaction temperature and the molar ratio of soybean oil to alcohol, were investigated and compared with those of non-catalyst runs. The catalytic transesterification ability of CaO is quite weak under ambient temperature. At a temperature of 335 K, the yield of methyl ester is only about 5% in 3 h. When CaO was added from 1.0% to 3.0%, the transesterification speed increased evidently, while when the catalyst content was further enhanced to 5%, the yield of methyl ester slowly reached to a plateau. It was observed that increasing the reaction temperature had a favorable influence on the methyl ester yield. In addition, for molar ratios ranging from 1 to 41, as the higher molar ratios of methanol to oil were charged, the greater transesterification speed was obtained. When the temperature was increased to 525 K, the transesterification reaction was essentially completed within 6 min with 3 wt% CaO and 41:1 methanol/oil molar ratio

Biodegradation and environmental behavior of biodiesel mixtures in the sea: An initial study.

Science.gov (United States)

DeMello, Jared A; Carmichael, Catherine A; Peacock, Emily E; Nelson, Robert K; Samuel Arey, J; Reddy, Christopher M

2007-07-01

Biodiesel, a mixture of fatty acid methyl esters (FAMEs) derived from animal fats or vegetable oils, is rapidly moving towards the mainstream as an alternative source of energy. However, the behavior of biodiesel, or blends of biodiesel with fossil diesel, in the marine environment have yet to be fully understood. Hence, we performed a series of initial laboratory experiments and simple calculations to evaluate the microbial and environmental fate of FAMEs. Aerobic seawater microcosms spiked with biodiesel or mixtures of biodiesel and fossil diesel revealed that the FAMEs were degraded at roughly the same rate as n-alkanes, and more rapidly than other hydrocarbon components. The residues extracted from these different microcosms became indistinguishable within weeks. Preliminary results from physical-chemical calculations suggest that FAMEs in biodiesel mixtures will not affect the evaporation rates of spilled petroleum hydrocarbons but may stabilize oil droplets in the water column and thereby facilitate transport.

Simple TLC-screening of acylglycerol levels in biodiesel as an alternative to GC determination.

Science.gov (United States)

Fontana, J D; Zagonel, G; Vechiatto, W W; Costa, B J; Laurindo, J C; Fontana, R; Pelisson, L; Jorge, B H; Lanças, F M

2009-10-01

Thin layer chromatography (TLC) stained with hot acidic p-anisaldehyde, is an interesting, fast, and low-cost technique to monitor main lipid contaminants such as triacylglycerols, diacylglycerols, and monoacylglycerols in biodiesel. These acylglycerols are detectable by the proposed planar chromatographic method, provided the content of the contaminants exceeds the limits recommended by the international norms applicable to biodiesel quality/specification, namely 0.25% in mass for total combined glycerin. The TLC data are confirmed by gas chromatography of the methyl esters of soy oil.

FAST GC-FID METHOD FOR MONITORING ACIDIC AND BASIC CATALYTIC TRANSESTERIFICATION REACTIONS IN VEGETABLE OILS TO METHYL ESTER BIODIESEL PREPARATION

Directory of Open Access Journals (Sweden)

Renata Takabayashi Sato

2016-04-01

Full Text Available A fast gas chromatography with a flame ionisation detector (GC-FID method for the simultaneous analysis of methyl palmitate (C16:0, stearate (C18:0, oleate (C18:1, linoleate (C18:2 and linolenate (C18:3 in biodiesel samples was proposed. The analysis was conducted in a customised ionic-liquid stationary-phase capillary, SLB-IL 111, with a length of 14 m, an internal diameter of 0.10 mm, a film thickness of 0.08 µm and operated isothermally at 160 °C using hydrogen as the carrier gas at a rate of 50 cm s-1 in run time about 3 min. Once methyl myristate (C14:0 is present lower than 0.5% m/m in real samples it was used as an internal standard. The method was successful applied to monitoring basic and acidic catalysis transesterification reactions of vegetable oils such as soybean, canola, corn, sunflower and those used in frying process.

Aprovechamiento de las oleinas residuales procedentes del proceso de refinado de los aceites vegetales comestibles, para la fabricación de biodiesel

Directory of Open Access Journals (Sweden)

Álvarez Mateos, P.

2003-06-01

Full Text Available A procedure to obtain Biodiesel from “Oleinas” is studied. Biodiesel is a suitable product to replace diesel oil currently used to power the Diesel engines. It consists of a mixture of methyl esters of the fatty acids presents as triglycerides in vegetables oils (olive, sunflower, soya, rape oils. As a result of the refining of these oils for their use as food, a waste product is formed, the “oleinas” (acidulated soapstock. The oleinas consist of a mixture of triglycerides and free fatty acids, the latter amounting to 50% or more of the mixture and are subject to a fluctuating market, therefore it exist at times a problem for their disposal. In our research work we have tried to obtain biodiesel from oleinas. The process resulting from our experimental work is as follows: 1. Sterification of the free fatty acids with methanol, by acid catalysis, centrifuging the reaction product and removal of the acid-methanol phase. Drying of the latter. At this stage we have a product containing about 70% of methyl esters. 2. Transesterification of the triglycerides present in the sterified product with methanol by alkaline catalysis, washing the reaction product with a water methanol solution. Centrifuging and removal of the water-methanol phase. At this stage a biodiesel product is obtained containing about 90% of methyl esters. 3. Fractional vacuum distillation of the 90% biodiesel gives a final product with a methyl esters content higher than 98%.Se estudia un procedimiento para la obtención de Biodiesel a partir de las “Oleínas”. Biodiesel es un producto capaz de sustituir al combustible Diesel ordinario que se obtiene del petróleo y que consiste en una mezcla de ésteres metílicos de ácidos grasos. Las oleínas son unos residuos que resultan del proceso de refinado de aceites vegetales para su uso alimentario y se componen de una mezcla de triglicéridos y ácidos grasos libres, con un contenido de estos últimos

Comparison of biodiesel production from sewage sludge obtained from the A²/O and MBR processes by in situ transesterification.

Science.gov (United States)

Qi, Juanjuan; Zhu, Fenfen; Wei, Xiang; Zhao, Luyao; Xiong, Yiqun; Wu, Xuemin; Yan, Fawei

2016-03-01

The potential of two types of sludge obtained from the anaerobic-anoxic-oxic (A(2)/O) and membrane bioreactor (MBR) processes as lipid feedstock for biodiesel production via in situ transesterification was investigated. Experiments were conducted to determine the optimum conditions for biodiesel yield using three-factor and four-level orthogonal and single-factor tests. Several factors, namely, methanol-to-sludge mass ratio, acid concentration, and temperature, were examined. The optimum yield of biodiesel (16.6% with a fatty acid methyl ester purity of 96.7%) from A(2)/O sludge was obtained at a methanol-to-sludge mass ratio of 10:1, a temperature of 60°C, and a H2SO4 concentration of 5% (v/v). Meanwhile, the optimum yield of biodiesel (4.2% with a fatty acid methyl ester purity of 92.7%) from MBR sludge was obtained at a methanol-to-sludge mass ratio of 8:1, a temperature of 50°C, and a H2SO4 concentration of 5% (v/v). In this research, A(2)/O technology with a primary sedimentation tank is more favorable for obtaining energy from wastewater than MBR technology. Copyright © 2016 Elsevier Ltd. All rights reserved.

Biodiesel emissions profile in modern diesel vehicles. Part 2: Effect of biodiesel origin on carbonyl, PAH, nitro-PAH and oxy-PAH emissions.

Science.gov (United States)

Karavalakis, Georgios; Boutsika, Vasiliki; Stournas, Stamoulis; Bakeas, Evangelos

2011-01-15

In the present study, the effects of different biodiesel blends on the unregulated emissions of a Euro 4 compliant passenger car were examined. Two fresh and two oxidized biodiesel fuels of different source materials were blended with an ultra low sulphur automotive diesel fuel at proportions of 10, 20, and 30% v/v. Emission measurements were conducted on a chassis dynamometer with a constant volume sampling (CVS) technique, over the New European Driving Cycle (NEDC) and the Artemis driving cycles. The experimental results revealed that the addition of biodiesel led to important increases in most carbonyl compounds. Sharp increases were observed with the use of the oxidized biodiesel blends, especially those prepared from used frying oil methyl esters. Similar to carbonyl emissions, most PAH compounds increased with the addition of the oxidized biodiesel blends. It can be assumed that the presence of polymerization products and cyclic acids, along with the degree of unsaturation were the main factors that influenced carbonyl and PAH emissions profile. Copyright © 2010 Elsevier B.V. All rights reserved.

Castor oil biodiesel as an alternative fuel for diesel engines

International Nuclear Information System (INIS)

Benavides, Alirio; Benjumea, Pedro; Pashova, Veselina

2007-01-01

In this paper, a study related to the production and use of castor oil biodiesel is presented. The maximum methyl esters yield of the castor oil transesterification reaction is obtained under the following conditions: ambient temperature, a molar ratio of methanol to vegetable oil equal to 9 and a catalyst percentage equal to 0.8%. The castor oil biodiesel can be blended with petroleum diesel as far as 15% in such way that the resulting blend complies with national and international technical standards for diesel fuels. Its high viscosity becomes the main difficulty for using castor oil biodiesel in engines. However this biofuel exhibits excellent cold flow properties (low values of cloud and pour points). The motor tests using castor oil biodiesel petroleum diesel blends, for the biodiesel proportion tested; show that a biodiesel percentage increase leads to an increase in the specific fuel consumption, a decrease in the fuel air ratio, a slight decrease in smoke opacity, while the fuel conversion efficiency and the CO and CO 2 emissions practically remain constants

Aspen Simulation of Diesel-Biodiesel Blends Combustion

Directory of Open Access Journals (Sweden)

Pérez-Sánchez Armando

2015-01-01

Full Text Available Biodiesel is a fuel produced by transesterification of vegetable oils or animal fats, which currently is gaining attention as a diesel substitute. It represents an opportunity to reduce CO2, SO2, CO, HC, PAH and PM emissions and contributes to the diversification of fuels in Mexico's energetic matrix. The results of the simulation of the combustion process are presented in this paper with reference to an engine specification KUBOTA D600-B, operated with diesel-biodiesel blends. The physicochemical properties of the compounds and the operating conditions of equipment were developed using the simulator Aspen® and supplementary information. The main aspects of the engine working conditions were considered such as diesel-biodiesel ratio, air/fuel mixture, temperature of the combustion gases and heat load. Diesel physicochemical specifications were taken from reports of PEMEX and SENER. Methyl esters corresponding to the transesterification of fatty acids that comprise castor oil were regarded as representative molecules of biodiesel obtained from chromatographic analysis. The results include CO2, water vapor, combustion efficiency, power and lower calorific value of fuels.

Evaporation and stability of biodiesel and blends with diesel in ambient conditions

Energy Technology Data Exchange (ETDEWEB)

Yang, Zeyu; Hollebone, Bruce P.; Wang, Zhendi; Yang, Chun; Landriault, Mike [Emergencies Science and Technology Section, Environment Canada (Canada)], email: bruce.hollebone@ec.gc.ca

2011-07-01

This study investigates the weathering behavior of biodiesel fuels or fuel blends with diesel in ambient conditions. The goal of this study is to reveal the influencing factors on biodiesel storage stability, and weathering and evaporation rates. Samples of Fatty Acid Methyl Ester (FAME) based biodiesel compounds, ultra-low sulfur diesel blends, and petroleum diesels were prepared separately for testing. After weathering the samples for 190 days, a series of chemical procedures, including hydrocarbon extraction and gas chromatography, were conducted to reveal the aging process of the mixtures. Due to their high boiling points, biodiesel concentrations in FAME compounds generally demonstrated lower evaporation rates than petroleum diesels, which showed a fast and high mass loss. Moreover, it was shown that adding biodiesel components to fuel blends did not affect the evaporation of diesel hydrocarbon. In general, FAME compounds exhibited good storage stability under ambient weathering.

Combustion of Pure, Hydrolyzed and Methyl Ester Formed of Jatropha Curcas Lin oil

Directory of Open Access Journals (Sweden)

Muhaji Muhaji

2015-10-01

Full Text Available The density and viscosity of vegetable oil are higher than that of diesel oil. Thus its direct combustion in the diesel engine results many problems. This research was conducted to investigate the flame characteristics of combustion of jatropha curcas lin in pure, hydrolyzed and methyl ester form. The results indicated that the combustion of pure jatropha curcas lin occurs in three stages, hydrolyzed in two stages    and methyl ester in one stage. For pure jatropha curcas lin, in the first stage, unsaturated fatty acid burned for  0.265 s.  It is followed by saturated fatty acid, burned for 0.389 s in the second stage. And, in the last stage is the burned of glycerol for 0.560 s. Meanwhile for hydrolyzed one, in the first stage, unsaturated fatty acid burned for 0.736 s, followed by saturated fatty acid, burned  for 0.326 s in the second stage. And the last, for methyl ester is the burned for 0.712 s. The highest burning rate was for methyl ester which was 0.003931cc/s. The energy releasing rate of methyl ester, which was for 13,628.67 kcal/(kg.s resembled that of diesel oil the most, while the lowest rate was for pure jatropha curcas lin which was 8,200.94 kcal/(kg.s. In addition, massive explosion occurred in the fuel containing unsaturated fatty acid and glycerol

Performance and emission characteristics of an agricultural diesel engine fueled with blends of Sal methyl esters and diesel

International Nuclear Information System (INIS)

Pali, Harveer S.; Kumar, N.; Alhassan, Y.

2015-01-01

Highlights: • Sal seed oil is unexplored biodiesel feedstock which is abundantly found in India. • Sal seed oil has good oxidation stability. • Performance and emission characteristics of the blends of Sal methyl esters with diesel evaluated. • At higher loads, CO, HC and smoke emissions of SME blends were lower than diesel. - Abstract: The present work deals with an underutilized vegetable oil; Sal seed oil (Shorea robusta) as a feedstock for biodiesel production. The production potential of Sal seed oil is very promising (1.5 million tons in a year) in India. The pressure filtered Sal seed oil was transesterified into Sal Methyl Ester (SME). The kinematic viscosity (5.89 cSt), density (0.8764 g/cc) and calorific value (39.65 MJ/kg) of the SME were well within the ASTM/EN standard limits. Various test fuels were prepared for the engine trials by blending 10%, 20%, 30% and 40% of SME in diesel on volumetric basis and designated as SME10, SME20, SME30 and SME40 respectively. The BTE, in general, was found to be decreased with increased volume fraction of SME in the blends. At full load, BSEC for SME10, SME20, SME30 and SME40 were 13.6 MJ/kW h, 14.3 MJ/kW h, 14.7 MJ/kW h and 14.8 MJ/kW h respectively as compared to 13.9 MJ/kW h in case of diesel. At higher load conditions, CO, UHC and smoke emissions were found lower for all SME blends in comparison to neat diesel due to oxygenated nature of fuel. SME10, SME20, SME30 and SME40 showed 51 ppm, 44 ppm, 46 ppm and 48 ppm of UHC emissions respectively as compared to 60 ppm of diesel. The NOx emissions were found to be increased for SME based fuel in comparison to neat diesel operation. At peak load condition, SME10, SME20, SME30 and SME40 had NOx emissions of 612 ppm, 644 ppm, 689 ppm and 816 ppm as compared to 499 ppm for diesel. It may be concluded from the experimental investigations that Sal seed biodiesel is a potential alternative to diesel fuel for reducing dependence on crude petroleum derived fuels and

Fatty acid methyl esters from soapstocks with potential use as biodiesel

International Nuclear Information System (INIS)

Yan Li; Xiao-dong Zhang; Li Sun

2010-01-01

Refined vegetable oils are the main feedstocks for biodiesel production presently. However, the source and price of refined vegetable oils always restrict the development of biodiesel industry in many regions. Large amount of cheap soapstocks (SSs) are currently available in oil refining process, which may provide potential feedstocks reservoir. In this paper, one technical route involving acidification, separation of free fatty acids (FFAs) and glycerides through molecular distillation, followed by esterification and transesterification, respectively, was proposed for effective conversion of SSs. The acid oil obtained from acidification of SSs was distilled at 180 C to isolate FFAs and glycerides. Esterification was then catalyzed by solid superacid catalyst, SO 4 2- /ZrO 2 -TiO 2 /La 3+ , with a methanol to oil ratio of 15:1, catalyst amount of 5 wt.% and reaction time 4 h at 60 C. The conversion efficiency could reach 98.02%. Transesterification with glycerides was also carried out with methanol to oil molar ratio of 5:1 and catalyst (sodium methoxide) amount of 0.6% and reaction time 0.5 h at 55 C. The conversion efficiency could reach 97.25%. Purification of transesterification products was operated at the evaporating temperature of 120 C. The content of FAME in the distillate was above 95% analysed by gas chromatography-mass spectrometry (GC-MS). (author)

Research into the application of biodiesel in the transport sector of Lithuania

Directory of Open Access Journals (Sweden)

S. Lebedevas

2006-06-01

Full Text Available The material of this publication presents the results of a complex research into the application of standard rapseed methyl ester (RME and new types of biodiesels produced from waste of vegetable oil and animal fat in the transport sector of Lithuania. The analytical analysis of physical, chemical and thermodynamical properties of biodiesels is performed and its results are evualated during the formation of tasks of experimental motor tests and research into mathematical modelling. Their influence for the paramaters of a working process and exploiting characteristics such as power, fuel economy, reliability and harmful emission of gases is evaluated.

Synthesis of biodiesel using potassium fluoride (KF) supported by hydrotalcite and process optimization by Box-Behnken design

Energy Technology Data Exchange (ETDEWEB)

Singh, Bhaskar; Sharma, Yogesh C. [Banaras Hindu University, Department of Applied Chemistry, Institute of Technology, Varanasi (India); Birla, Ashish; Upadhyay, S.N. [Banaras Hindu University, Department of Chemical Engineering and Technology, Institute of Technology, Varanasi (India); Yaakob, Zahira [Universiti Kebangsaan Malaysia, Department of Chemical and Process Engineering, Selangor (Malaysia)

2012-12-15

Biodiesel has been developed using a heterogeneous catalyst potassium fluoride (KF) supported on hydrotalcite (HT) and waste frying oil (WFO) as feedstock. Hydrotalcite was synthesized by co-precipitation method using mixture of Mg(NO{sub 3}){sub 2}.6H{sub 2}O and Al(NO{sub 3}){sub 2}.9H{sub 2}O slowly added to a solution containing NaOH and Na{sub 2}CO{sub 3} and calcined at 500 C. KF was impregnated on hydrotalcite at KF/HT load ratio of 80:100 by addition of a small amount of water. Biodiesel was developed using KF/HT as heterogeneous catalyst by transesterification. Box-Behnken Design using Minitab 15.1 Statistical Software and Design-Expert (Demo version 8.0.6.1) software were used as statistical tool for design of experiments and optimization of fatty acid methyl ester yield. A high yield and conversion of biodiesel was obtained by optimization of variables affecting the reaction. The variables affected the reaction in the priority order of: catalyst amount >> molar ratio (methanol to oil) > reaction time. A 12:1 methanol to WFO molar ratio, 2.5 wt.% of catalyst at 60 C in 1 h reaction time gave a high fatty acid methyl ester yield of >98 %. The quantitative analysis of the product (i.e., biodiesel) was done on a Fourier-transform-nuclear magnetic resonance spectrometer. (orig.)

Experimental study on evaluation and optimization of conversion of waste chicken fat into biodiesel

International Nuclear Information System (INIS)

Andrade, J.E.; Sebastian, P.J.; Perez, A.

2009-01-01

Full text: This study was initiated to evaluate and optimize the conversion of waste chicken fat (WCF) into ethyl and methyl ester called biodiesel. The physical and chemical characteristics of these esters were much closer to those of Diesel fuel than those of fresh vegetable oil or fat, which makes them a good substitute for Diesel fuel. Experiments have been performed to determine the optimum conditions for this conversion process using a three factor factorial design for producing biodiesel. The major variables in the transesterification process are determined from the pre experiments as: reaction temperature, molar ratio of alcohol/oil, alcohol type utilized and catalyst type. Absolute ethanol was found better than absolute methanol, since ethanol gives higher conversion and less viscosity at all levels, mainly at 100% excess concentration. Temperature had no detectable effect on the ultimate conversion ratio and viscosity for both ester products. However, higher temperatures decreases the time required to reach maximum conversion, which will be at the expense of the cost of energy. An interaction between time and temperature was found for all conversions. Therefore, 60 C was found to be the optimum temperature, and one hour is the optimum time for the conversion of WAFs into biodiesel. The obtained product with 97.02% of biodiesel was analyzed and characterized by gas chromatography. (author)

Ultrasonication Assisted Production of Biodiesel from Sunflower Oil by Using CuO: Mg Heterogeneous Nanocatalyst

Science.gov (United States)

Varghese, Rintu; Jose, Sony; Joyprabu, H.; Johnson, I.

2017-08-01

Biodiesel is a clean, renewable, biodegradable, eco-friendly and alternative fuel used in the diesel engine. The present work was carried out at constant operational conditions such as methanol to oil molar ratio 6:1, catalyst concentration 0.25%, 30 minute reaction time and the reaction temperature at 60°C. Biodiesel was synthesized by transesterification of sunflower oil (SFO) with methanol, using CuO: Mgas nanocatalyst. This nanocatalyst was prepared by quick precipitation method. The biodiesel yield of 71.78% was achieved under reaction condition. The presence of methyl ester groups at the produced biodiesel was confirmed using the Gas Chromatography-Mass Spectrometry (GC-MS). The FAME conversion yield up to 82.83 % could be obtained under the operating conditions.

Alternative fuels in fire debris analysis: biodiesel basics.

Science.gov (United States)

Stauffer, Eric; Byron, Doug

2007-03-01

Alternative fuels are becoming more prominent on the market today and, soon, fire debris analysts will start seeing them in liquid samples or in fire debris samples. Biodiesel fuel is one of the most common alternative fuels and is now readily available in many parts of the United States and around the world. This article introduces biodiesel to fire debris analysts. Biodiesel fuel is manufactured from vegetable oils and/or animal oils/fats. It is composed of fatty acid methyl esters (FAMEs) and is sold pure or as a blend with diesel fuel. When present in fire debris samples, it is recommended to extract the debris using passive headspace concentration on activated charcoal, possibly followed by a solvent extraction. The gas chromatographic analysis of the extract is first carried out with the same program as for regular ignitable liquid residues, and second with a program adapted to the analysis of FAMEs.

A microfluidic device for the automated derivatization of free fatty acids to fatty acid methyl esters.

Science.gov (United States)

Duong, Cindy T; Roper, Michael G

2012-02-21

Free fatty acid (FFA) compositions are examined in feedstock for biodiesel production, as source-specific markers in soil, and because of their role in cellular signaling. However, sample preparation of FFAs for gas chromatography-mass spectrometry (GC-MS) analysis can be time and labor intensive. Therefore, to increase sample preparation throughput, a glass microfluidic device was developed to automate derivatization of FFAs to fatty acid methyl esters (FAMEs). FFAs were delivered to one input of the device and methanolic-HCl was delivered to a second input. FAME products were produced as the reagents traversed a 29 μL reaction channel held at 55 °C. A Design of Experiment protocol was used to determine the combination of derivatization time (T(der)) and ratio of methanolic-HCl:FFA (R(der)) that maximized the derivatization efficiencies of tridecanoic acid and stearic acid to their methyl ester forms. The combination of T(der) = 0.8 min and R(der) = 4.9 that produced optimal derivatization conditions for both FFAs within a 5 min total sample preparation time was determined. This combination of T(der) and R(der) was used to derivatize 12 FFAs with a range of derivatization efficiencies from 18% to 93% with efficiencies of 61% for tridecanoic acid and 84% for stearic acid. As compared to a conventional macroscale derivatization of FFA to FAME, the microfluidic device decreased the volume of methanolic-HCl and FFA by 20- and 1300-fold, respectively. The developed microfluidic device can be used for automated preparation of FAMEs to analyze the FFA compositions of volume-limited samples.

Synthesis of Dipeptide Benzoylalanylglycine Methyl Ester and Corrosion Inhibitor Evaluation by Tafel Equation

International Nuclear Information System (INIS)

Abdurrahman, J.; Wahyuningrum, D.; Achmad, S.; Bundjali, B.

2011-01-01

Corrosion is one of the major problems in petroleum mining and processing industry. The pipelines used to transport crude oil from reservoir to the processing installation were made from carbon steel that is susceptible towards corrosion. One of the best methods to prevent corrosion that occurred at the inner parts of carbon steel pipelines is to use organic corrosion inhibitor. One of the potent organic corrosion inhibitors is amino acids derivatives. In this study, dipeptide compound namely benzoylalanylglycine methyl ester and benzoylalanylglycine have been synthesized. The structure elucidation of the products was performed by IR, MS and NMR spectroscopy. The determination of corrosion inhibition activity utilized the Tafel method. The corrosion inhibition efficiency of glycine methyl ester, benzoyl alanine, dipeptide benzoylalanylglycine methyl ester and dipeptide benzoylalanylglycine were 63.34 %, 35.86 %, 68.40 % and 27.72 %, respectively. These results showed that the formation of dipeptide benzoylalanylglycine methyl ester, derived from carboxylic protected glycine and amine protected alanine, increased the corrosion inhibition activity due to the loss of acidity center in the structure of glycine and L-alanine that would induce the corrosive environment towards carbon steel. (author)

PM-10 emissions and power of a Diesel engine fueled with crude and refined Biodiesel from salmon oil

Energy Technology Data Exchange (ETDEWEB)

J.F. Reyes; M.A. Sepulveda [University of Concepcion (Chile). Department of Mechanization and Energy, Faculty of Agricultural Engineering

2006-09-15

Power response and level of particulate emissions were assessed for blends of Diesel-crude Biodiesel and Diesel-refined Biodiesel. Crude Biodiesel and refined Biodiesel or methyl ester, were made from salmon oil with high content of free fatty acids, throughout a process of acid esterification followed by alkaline transesterification. Blends of Diesel-crude Biodiesel and Diesel-refined Biodiesel were tested in a diesel engine to measure simultaneously the dynamometric response and the particulate material (PM-10) emission performance. The results indicate a maximum power loss of about 3.5% and also near 50% of PM-10 reduction with respect to diesel when a 100% of refined Biodiesel is used. For blends with less content of either crude Biodiesel or refined Biodiesel, the observed power losses are lower but at the same time lower reduction in PM-10 emissions are attained. 21 refs., 4 figs., 2 tabs.

Synthesis of Biodiesel from the Oily Content of Marine Green Alga Ulva fasciata

International Nuclear Information System (INIS)

Khan, A. M.; Fatima, N.

2015-01-01

The present study is focused on the chemical transformation of oils derived from the marine green alga Ulva fasciata Delile to biodiesel. The transesterification of algal oil was performed with a variety of alcohols using Na metal and NaOH as catalysts. Transesterification of algal oil by mechanical stirring yielded significant biodiesel within an hour at 60 degree C with NaOH and at room temperature with Na metal. In addition, microwave irradiated transesterification produced significant amount of biodiesel with NaOH and Na metal within 1-5 minutes. However, reaction of sodium metal in microwave oven was highly exothermic and uncontrollable that could also damage the radiation source. The reactivity order of alcohols was found to be methanol > ethanol > benzyl alcohol > 1-propanol > 1-butanol > 1-pentanol > 1-hexanol > 2-propanol. Isopropyl alcohol was found to be least reactive due to steric hindrance. Benzyl alcohol was found to be more reactive than 1-propyl alcohol due to the electron withdrawing effect of benzene ring. The highest % conversion of FAME and FAEE were found to be 97% and 98% respectively using Na metal through mechanical stirring. Biodiesel production was confirmed by thin layer chromatography (TLC). Furthermore, the fuel properties including density, kinematics viscosity, high heating value, acid value, free fatty acid (%), cloud point and pour point of U. fasciata oil and all the esters were determined and compared with the standard limits of biodiesel. Fatty acid methyl, ethyl, 1-propyl, 2-propyl, 1-butyl, 1-pentyl and 1-hexyl esters showed the fuel properties within the biodiesel standard limits therefore all of them were considered as the substitute of biodiesel. On the other hand, the fuel properties of benzyl ester were found to be above the limits of biodiesel specifications and thus it could not be considered as biodiesel. This research article will be helpful to overcome the current challenges of energy crisis, global warming and

Rapid biodiesel synthesis from waste pepper seeds without lipid isolation step.

Science.gov (United States)

Lee, Jechan; Kim, Jieun; Ok, Yong Sik; Kwon, Eilhann E

2017-09-01

In situ transformation of lipid in waste pepper seeds into biodiesel (i.e., fatty acid methyl esters: FAMEs) via thermally-induced transmethylation on silica was mainly investigated in this study. This study reported that waste pepper seeds contained 26.9wt% of lipid and that 94.1% of the total lipid in waste pepper seeds could be converted into biodiesel without lipid extraction step for only ∼1min reaction time. This study also suggested that the optimal temperature for in situ transmethylation was identified as 390°C. Moreover, comparison of in situ process via the conventional transmethylation catalyzed by H 2 SO 4 showed that the introduced biodiesel conversion in this study had a higher tolerance against impurities, thereby being technically feasible. The in situ biodiesel production from other oil-bearing food wastes can be studied. Copyright © 2017 Elsevier Ltd. All rights reserved.

Process intensification for biodiesel production from Jatropha curcas L. seeds: Supercritical reactive extraction process parameters study

International Nuclear Information System (INIS)

Lim, Steven; Lee, Keat Teong

2013-01-01

Highlights: ► Investigation of supercritical reactive extraction process for biodiesel production. ► Focus is given on optimizing methyl esters yield for Jatropha curcas L. seeds. ► Influence of process parameters to the reaction are discussed thoroughly. ► Comparison between the novel reaction with conventional process are studied. ► High methyl esters yield can be obtained without pre-extraction and catalyst. -- Abstract: In a bid to increase the cost competitiveness of biodiesel production against mineral diesel, process intensification has been studied for numerous biodiesel processing technologies. Subsequently, reactive extraction or in situ transesterification is actively being explored in which the solid oil-bearing seeds are used as the reactant directly with short-chain alcohol. This eliminates separate oil extraction process and combines both extraction and transesterification in a single unit. Supercritical reactive extraction takes one step further by substituting the role of catalyst with supercritical conditions to achieve higher yield and shorter processing time. In this work, supercritical reactive extraction with methanol was carried out in a high-pressure batch reactor to produce fatty acid methyl esters (FAMEs) from Jatropha curcas L. seeds. Material and process parameters including space loading, solvent to seed ratio, co-solvent (n-hexane) to seed ratio, reaction temperature, reaction time and mixing intensity were varied one at a time and optimized based on two responses i.e. extraction efficiency, M extract and FAME yield, F y . The optimum responses for supercritical reactive extraction obtained were 104.17% w/w and 99.67% w/w (relative to 100% lipid extraction with n-hexane) for M extract and F y respectively under the following conditions: 54.0 ml/g space loading, 5.0 ml/g methanol to seeds ratio, 300 °C, 9.5 MPa (Mega Pascal), 30 min reaction time and without n-hexane as co-solvent or any agitation source. This proved that

Preliminary study of used cooking oil methyl ester as an alternative fuel for diesel engine

International Nuclear Information System (INIS)

Roseli, A.; El-Awad, M.M.; Yusoff, M.Z.

2006-01-01

An experimental work has been carried out to compare the power performance and exhaust emissions of UCOME with OD on unmodified direct injection, four stroke single cylinder and stationary Robin diesel engine. Used cooking oil was transesterified by using methanol that yields immiscible fraction of glycerol and methyl ester (biodiesel). UCOME was separated by gravity before conducting further testing on its physical, chemical and thermal properties in the laboratory. For fuel power performance analysis, fuel consumption, gross energy input, torque, brake power, BMEP and SFC of the engine were measured and calculated. The analysis showed that at high engine speeds, the engine performances with UCOME are comparable to that of OD. However, UCOME increases specific fuel consumption due to its high specific density. In term of exhaust emissions UCOME showed a net reduction in exhaust emissions of NO x as compared with those of OD. This study has given optimistic information to pave the direction for further research on diesel engine

Analysis of transesterification comparing processes with methanol and ethanol for biodiesel production

Energy Technology Data Exchange (ETDEWEB)

Pighinelli, Anna Leticia Montenegro Turtelli; Zorzeto, Thais Queiroz; Park, Kil Jin [Universidade Estadual de Campinas (FEAGRI/UNICAMP), SP (Brazil). Fac. de Engenharia Agricola], E-mail: annalets@feagri.unicamp.br; Bevilaqua, Gabriela [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Inst. de Quimica

2008-07-01

The increasing demand for energy on the industrialized world stimulates researches in a renewable fuel. Biodiesel appears like an alternative and utilizes a vegetable oil or animal fat as raw material. The most common method for conversion of the raw material in fuel that can be utilized in Diesel engines is called transesterification. Brazil has a big agricultural potential to produce grains and oils. One of them is the peanut oil that is predominantly cultivated in the southeast of Brazil. There is a prevision that the peanut production reaches 232 thousand tons this year. In this work was evaluated the methanol transesterification and ethanol transesterification of peanut oil using a basic catalyst. The comparison between reactions with the two alcohols showed that methyl esters yield was greater than ethyl esters, with maximum yield of 88.04% for methanol and 84.64% for ethanol. Besides the higher yield, reactions with methanol are easily conducted than with ethanol, the biodiesel purification treatment of final product is quickly and the separation between esters and glycerol is instantaneous. (author)

Karanja (Pongamia Pinnata) biodiesel production in Bangladesh, characterization of karanja biodiesel and its effect on diesel emissions

Energy Technology Data Exchange (ETDEWEB)

Nabi, Md. Nurun; Hoque, S.M. Najmul; Akhter, Md. Shamim [Department of Mechanical Engineering, RUET (Bangladesh)

2009-09-15

This paper presents production of biodiesel (BD) from non-edible renewable karanja (Pongamia Pinnata) oil, determination of BD properties and influence of BD on engine performance and emissions. Bangladesh imports 2.4 million metric ton (MT) DF each year [M.N. Nabi, M.S. Akhter, K.M.F. Islam, Prospect of biodiesel production from jatropha curcas, a promising non edible oil seed in Bangladesh, International Conference on Mechanical Engineering (ICME, Dhaka, Bangladesh) Proceedings 2007, paper no. ICME07-TH-06. ]. It has 0.32 million hectare of unused land [M.N. Nabi, S.M.N. Hoque, M.S. Uddin, Prospect of Jatropha curcas and pithraj cultivation in Bangladesh, Journal of Engineering and Technology, IUT, Dhaka, Bangladesh, 7 (1) (2009) 41-54. ]. It has been found that cultivating of karanja plant in such unused land; Bangladesh can reduce DF import by 28%. Karanja methyl ester (KME), which is termed as BD, has been produced by well-known transesterification process. The properties of B100 (B100) and its blends were determined mainly according to ASTM standard and some of them were as per EN14214 standard. The Fourier transform infrared (FTIR) analysis showed that the DF fuel contained mainly alkanes and alkens, while the B100 contained mainly esters. The gas chromatography (GC) of B100 revealed that a maximum of 97% methyl ester was produced from karanja oil. Engine experiment result showed that all BD blends reduced engine emissions including carbon monoxide (CO), smoke and engine noise, but increased oxides of nitrogen (NOx). Compared to DF, B100 reduced CO, and smoke emissions by 50 and 43%, while a 15% increase in NOx emission was observed with the B100. Compared to DF, engine noise with B100 was reduced by 2.5 dB. (author)

Karanja (Pongamia Pinnata) biodiesel production in Bangladesh, characterization of karanja biodiesel and its effect on diesel emissions

International Nuclear Information System (INIS)

Nabi, Md. Nurun; Hoque, S.M. Najmul; Akhter, Md. Shamim

2009-01-01

This paper presents production of biodiesel (BD) from non-edible renewable karanja (Pongamia Pinnata) oil, determination of BD properties and influence of BD on engine performance and emissions. Bangladesh imports 2.4 million metric ton (MT) DF each year [M.N. Nabi, M.S. Akhter, K.M.F. Islam, Prospect of biodiesel production from jatropha curcas, a promising non edible oil seed in Bangladesh, International Conference on Mechanical Engineering (ICME, Dhaka, Bangladesh) Proceedings 2007, paper no. ICME07-TH-06. ]. It has 0.32 million hectare of unused land [M.N. Nabi, S.M.N. Hoque, M.S. Uddin, Prospect of Jatropha curcas and pithraj cultivation in Bangladesh, Journal of Engineering and Technology, IUT, Dhaka, Bangladesh, 7 (1) (2009) 41-54. ]. It has been found that cultivating of karanja plant in such unused land; Bangladesh can reduce DF import by 28%. Karanja methyl ester (KME), which is termed as BD, has been produced by well-known transesterification process. The properties of B100 (B100) and its blends were determined mainly according to ASTM standard and some of them were as per EN14214 standard. The Fourier transform infrared (FTIR) analysis showed that the DF fuel contained mainly alkanes and alkens, while the B100 contained mainly esters. The gas chromatography (GC) of B100 revealed that a maximum of 97% methyl ester was produced from karanja oil. Engine experiment result showed that all BD blends reduced engine emissions including carbon monoxide (CO), smoke and engine noise, but increased oxides of nitrogen (NOx). Compared to DF, B100 reduced CO, and smoke emissions by 50 and 43%, while a 15% increase in NOx emission was observed with the B100. Compared to DF, engine noise with B100 was reduced by 2.5 dB. (author)

Thermal Decomposition of Potential Ester Biofuels. Part I: Methyl Acetate and Methyl Butanoate

Energy Technology Data Exchange (ETDEWEB)

Porterfield, Jessica P.; Bross, David H.; Ruscic, Branko; Thorpe, James H.; Nguyen, Thanh Lam; Baraban, Joshua H.; Stanton, John F.; Daily, John W.; Ellison, G. Barney

2017-06-09

Two methyl esters have been examined as models for the pyrolysis of biofuels. Dilute samples (0.06 - 0.13%) of methyl acetate (CH₃COOCH₃) and methyl butanoate (CH₃CH₂CH₂COOCH₃) were entrained in (He, Ar) carrier gas and decomposed in a set of flash-pyrolysis micro-reactors. The pyrolysis products resulting from the methyl esters were detected and identified by vacuum ultraviolet photoionization mass spectrometry. Complementary product identification was provided by matrix infrared absorption spectroscopy. Pyrolysis pressures in the pulsed micro-reactor were roughly 20 Torr and residence times through the reactors were approximately 25 - 150 µs. Reactor temperatures of 300 – 1600 K were explored. Decomposition of CH₃COOCH₃ commences at 1000 K and the initial products are (CH₂=C=O and CH₃OH). As the micro-reactor is heated to 1300 K, a mixture of (CH₂=C=O and CH₃OH, CH₃, CH₂=O, H, CO, CO₂) appears. The thermal cracking of CH₃CH₂CH₂COOCH₃ begins at 800 K with the formation of (CH₃CH₂CH=C=O, CH₃OH). By 1300 K, the pyrolysis of methyl butanoate yields a complex mixture of (CH₃CH₂CH=C=O, CH₃OH, CH₃, CH₂=O, CO, CO₂, CH₃CH=CH₂, CH₂CHCH₂, CH₂=C=CH₂, HCCCH₂, CH₂=C=C=O, CH₂=CH₂, HCΞCH, CH₂=C=O). Based on the results from the thermal cracking of methyl acetate and methyl butanoate, we predict several important decomposition channels for the pyrolysis of fatty acid methyl esters, R CH₂-COOCH₃. The lowest energy fragmentation will be a 4-center elimination of methanol to form the ketene, RCH=C=O. At higher temperatures, concerted

Mississippi State Biodiesel Production Project

Energy Technology Data Exchange (ETDEWEB)

Rafael Hernandez; Todd French; Sandun Fernando; Tingyu Li; Dwane Braasch; Juan Silva; Brian Baldwin

2008-03-20

tallow tree and tung tree. High seed yields from these species are possible because, there stature allows for a third dimension in yield (up). Harvest regimes have already been worked out with tung, and the large seed makes shedding of the seed with tree shakers possible. While tallow tree seed yields can be mind boggling (12,000 kg seed/ha at 40% oil), genotypes that shed seed easily are currently not known. Efficient methods were developed to isolate polyunsaturated fatty acid methyl esters from bio-diesel. The hypothesis to isolate this class of fatty acids, which are used as popular dietary supplements and prescription medicine (OMACOR), was that they bind transition metal ions much stronger than their harmful saturated analogs. AgBF4 has the highest extraction ability among all the metal ions tested. Glycerol is a key product from the production of biodiesel. It is produced during the transesterification process by cleaving the fatty acids from the glycerol backbone (the fatty acids are used as part of the biodiesel, which is a fatty acid methyl ester). Glycerol is a non-toxic compound with many uses; however, if a surplus exists in the future, more uses for the produced glycerol needs to be found. Another phase of the project was to find an add-on process to the biodiesel production process that will convert the glycerol by-product into more valuable substances for end uses other than food or cosmetics, focusing at present on 1,3-propanediol and lactic acid.All three MSU cultures produced products at concentrations below that of the benchmark microorganisms. There was one notable isolate the caught the eye of the investigators and that was culture J6 due to the ability of this microorganism to co-produce both products and one in particularly high concentrations. This culture with more understanding of its metabolic pathways could prove a useful biological agent for the conversion of glycerol. Heterogeneous catalysis was examined as an alternative to overcome the

Production of Biodiesel from Pinus Roxburghii Oil and its Evaluation

International Nuclear Information System (INIS)

Ishfaq, M.; Ahmad, I.; Shakiruliah, M.; Saeed, K.

2013-01-01

Biodiesel fuel is an alternative and renewable source of energy. It may help to reduce air pollution and our dependence on fossil fuel for energy. In this study the plant oil was extracted from saw dust of pine tree using methanol as a solvent and acid catalyst (H/sub 2/SO/sub 4/) was used for transesterification. The effect of reaction time, temperature and catalyst ratio was studied, which presented that the high yield of biodiesel is produced by using 9 mL of catalyst for 1 h reaction time. The physicochemical properties such as density, viscosity, heating value, cetane index, flash point, Conradson carbon residue and distillation behavior of the obtained biodiesel were determined. The results showed that the final fatty acid methyl esters (FAME) product meets with the biodiesel quality standards, and ASTM specification D6751-02. The UV-Visible and FT-IR spectroscopic studies was also performed, which revealed that the synthesized biodiesel consists of aliphatic, olifinic and aromatic hydrocarbons along with fatty acids. (author)

Diorganotin(IV) Complexes with Methionine Methyl Ester. Equilibria ...

African Journals Online (AJOL)

IV) (DBT) and diphenyltin(IV) (DPT) was investigated at 25 °C and 0.1 mol dm–3 ionic strength in water for dimethyltin(IV) and in 50 % dioxane–water mixture for dibutyltin(IV) and diphenyltin(IV). Methionine methyl ester forms1:1 and 1:2 ...

Biodiesel from wet microalgae: extraction with hexane after the microwave-assisted transesterification of lipids.

Science.gov (United States)

Cheng, Jun; Huang, Rui; Li, Tao; Zhou, Junhu; Cen, Kefa

2014-10-01

A chloroform-free novel process for the efficient production of biodiesel from wet microalgae is proposed. Crude biodiesel is produced through extraction with hexane after microwave-assisted transesterification (EHMT) of lipids in wet microalgae. Effects of different parameters, including reaction temperature, reaction time, methanol dosage, and catalyst dosage, on fatty acids methyl esters (FAMEs) yield are investigated. The yield of FAME extracted into the hexane from the wet microalgae is increased 6-fold after the transesterification of lipids. The yield of FAME obtained through EHMT of lipids in wet microalgae is comparable to that obtained through direct transesterification of dried microalgae biomass with chloroform; however, FAME content in crude biodiesel obtained through EHMT is 86.74%, while that in crude biodiesel obtained through the chloroform-based process is 75.93%. EHMT ensures that polar pigments present in microalgae are not extracted into crude biodiesel, which leads to a 50% reduction in nitrogen content in crude biodiesel. Copyright © 2014 Elsevier Ltd. All rights reserved.

Biodiesel Production from Chlorella protothecoides Oil by Microwave-Assisted Transesterification

OpenAIRE

G?lyurt, Mustafa ?mer; ?z?imen, Didem; ?nan, Benan

2016-01-01

In this study, biodiesel production from microalgal oil by microwave-assisted transesterification was carried out to investigate its efficiency. Transesterification reactions were performed by using Chlorella protothecoides oil as feedstock, methanol, and potassium hydroxide as the catalyst. Methanol:oil ratio, reaction time and catalyst:oil ratio were investigated as process parameters affected methyl ester yield. 9:1 methanol/oil molar ratio, 1.5% KOH catalyst/oil ratio and 10 min were opti...

Biodiesel Production from Waste Cooking Oil Using Hydrodinamic Cavitation

Directory of Open Access Journals (Sweden)

Muhammad Supardan

2013-04-01

Full Text Available The aim of this research was to study biodiesel production from low cost feedstock of waste cooking oil (WCO using hydrodynamic cavitation apparatus. A two-step processes esterification process and transesterification process using hydrodynamic cavitation for the production of biodiesel from WCO is presented. The first step is acid-catalyzed esteri-fication process for reducing free fatty acid (FFA content of WCO and followed by base-catalyzed transesterification process for converting WCO to biodiesel as the second step. The result of esterification process with methanol to oil molar ratio of 5 and temperature of 60 oC showed that the initial acid value of WCO of 3.9 mg KOH/g can be decreased to 1.81 mg KOH/g in 120 minutes. The highest yield of biodiesel in transesterification process of 89.4% obtained at reaction time of 150 minutes with methanol to oil molar ratio of 6. The biodiesel produced in the experiment was analyzed by gas chromatography-mass spectrometry (GC-MS, which showed that it mainly contained five fatty acid methyl esters. In addition, the properties of biodiesel showed that all of the fuel properties met the Indonesian National Standard (INS No. 04-7182-2006 for biodiesel. 

Biodiesel Production From the Microalgae Nannochloropsis by Microwave Using CaO and MgO Catalysts

Directory of Open Access Journals (Sweden)

Herman Hindarso

2015-02-01

Full Text Available The needs of world petroleum are increased; in contrast, the fuel productions are getting decreased. Therefore, it has lead to the search for bio-fuel as an alternative energy. There are several different types of biofuel, such as biodiesel, ethanol, bioalcohol, and biogas. Biodiesel is typically made by chemically reacting lipids from a vegetable oil or animal fat with an alcohol producing fatty acid esters, such as methyl or ethyl ester. The present study aimed to study the effect of temperature (50, 60 and 65°C, reaction time (1 to 5 minutes dan types of catalyst (CaO dan MgO of 1 and 3 % in the production of biodiesel from microalgae by the transesterification process using microwave methods. It also studied the characteristics of biodiesel which had the greatest yield in the present study, i.e. flash point, cetane number, density, viscosity, and FAME. The greatest yield was 99.35% and obtained with combination of 3% MgO catalyst quantity at temperature of 60°C, in 3 minutes reaction time. At this process conditions, the biodiesel has a flash point of 122°C, cetane number of 55, density of  0.89, viscosity of 5 cP and FAME of 75.12 %.

An ultrasound-assisted system for the optimization of biodiesel production from chicken fat oil using a genetic algorithm and response surface methodology.

Science.gov (United States)

Fayyazi, E; Ghobadian, B; Najafi, G; Hosseinzadeh, B; Mamat, R; Hosseinzadeh, J

2015-09-01

Biodiesel is a green (clean), renewable energy source and is an alternative for diesel fuel. Biodiesel can be produced from vegetable oil, animal fat and waste cooking oil or fat. Fats and oils react with alcohol to produce methyl ester, which is generally known as biodiesel. Because vegetable oil and animal fat wastes are cheaper, the tendency to produce biodiesel from these materials is increasing. In this research, the effect of some parameters such as the alcohol-to-oil molar ratio (4:1, 6:1, 8:1), the catalyst concentration (0.75%, 1% and 1.25% w/w) and the time for the transesterification reaction using ultrasonication on the rate of the fatty acids-to-methyl ester (biodiesel) conversion percentage have been studied (3, 6 and 9 min). In biodiesel production from chicken fat, when increasing the catalyst concentration up to 1%, the oil-to-biodiesel conversion percentage was first increased and then decreased. Upon increasing the molar ratio from 4:1 to 6:1 and then to 8:1, the oil-to-biodiesel conversion percentage increased by 21.9% and then 22.8%, respectively. The optimal point is determined by response surface methodology (RSM) and genetic algorithms (GAs). The biodiesel production from chicken fat by ultrasonic waves with a 1% w/w catalyst percentage, 7:1 alcohol-to-oil molar ratio and 9 min reaction time was equal to 94.8%. For biodiesel that was produced by ultrasonic waves under a similar conversion percentage condition compared to the conventional method, the reaction time was decreased by approximately 87.5%. The time reduction for the ultrasonic method compared to the conventional method makes the ultrasonic method superior. Copyright © 2015. Published by Elsevier B.V.

A simple and sensitive fluorescent sensor for methyl parathion based on L-tyrosine methyl ester functionalized carbon dots.

Science.gov (United States)

Hou, Juying; Dong, Jing; Zhu, Haishuang; Teng, Xue; Ai, Shiyun; Mang, Minglin

2015-06-15

In this paper, a simple and sensitive fluorescent sensor for methyl parathion is developed based on L-tyrosine methyl ester functionalized carbon dots (Tyr-CDs) and tyrosinase system. The carbon dots are obtained by simple hydrothermal reaction using citric acid as carbon resource and L-tyrosine methyl ester as modification reagent. The carbon dots are characterized by transmission electron microscope, high resolution transmission electron microscopy, X-ray diffraction spectrum, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The carbon dots show strong and stable photoluminescence with a quantum yield of 3.8%. Tyrosinase can catalyze the oxidation of tyrosine methyl ester on the surface of carbon dots to corresponding quinone products, which can quench the fluorescence of carbon dots. When organophosphorus pesticides (OPs) are introduced in system, they can decrease the enzyme activity, thus decrease the fluorescence quenching rate. Methyl parathion, as a model of OPs, was detected. Experimental results show that the enzyme inhibition rate is proportional to the logarithm of the methyl parathion concentration in the range 1.0×10(-10)-1.0×10(-4) M with the detection limit (S/N=3) of 4.8×10(-11) M. This determination method shows a low detection limit, wide linear range, good selectivity and high reproducibility. This sensing system has been successfully used for the analysis of cabbage, milk and fruit juice samples. Copyright © 2014 Elsevier B.V. All rights reserved.

Determination of 4-Chloroindole-3-Acetic Acid Methyl Ester in Lathyrus Vicia and Pisum by Gas Chromatography - Mass Spectrometry

DEFF Research Database (Denmark)

Engvild, Kjeld Christensen; Egsgaard, Helge; Larsen, Elfinn

1980-01-01

4-Chloroindole-3-acetic acid methyl ester was identified unequivocally in Lathyrus latifolius L., Vicia faba L. and Pisum sativum L. by thin layer chromatography, gas chromatography and mass spectrometry. The gas chromatographic system was able to separate underivatized chloroindole-3-acetic acid...... methyl ester isomers. The quantitative determination of 4-chloroindole-3-acetic acid methyl ester in immature seeds of these three species was performed by gas chromatography – mass spectrometry using deuterium labelled 4-chloro-indole-3-acetic acid methyl ester as an internal standard. P. sativum...

Okra (Hibiscus esculentus) seed oil for biodiesel production

Energy Technology Data Exchange (ETDEWEB)

Anwar, Farooq; Nadeem, Muhammad [Department of Chemistry and Biochemistry, University of Agriculture, Faisalabad 38040 (Pakistan); Rashid, Umer [Department of Chemistry and Biochemistry, University of Agriculture, Faisalabad 38040 (Pakistan); Department of Industrial Chemistry, Government College University, Faisalabad 38000 (Pakistan); Ashraf, Muhammad [Department of Botany, University of Agriculture, Faisalabad 38040 (Pakistan)

2010-03-15

Biodiesel was derived from okra (Hibiscus esculentus) seed oil by methanol-induced transesterification using an alkali catalyst. Transesterification of the tested okra seed oil under optimum conditions: 7:1 methanol to oil molar ratio, 1.00% (w/w) NaOCH{sub 3} catalyst, temperature 65 C and 600 rpm agitation intensity exhibited 96.8% of okra oil methyl esters (OOMEs) yield. The OOMEs/biodiesel produced was analyzed by GC/MS, which showed that it mainly consisted of four fatty acids: linoleic (30.31%), palmitic (30.23%), oleic (29.09%) and stearic (4.93%). A small amount of 2-octyl cyclopropaneoctanoic acid with contribution 1.92% was also established. Fuel properties of OOMEs such as density, kinematic viscosity, cetane number, oxidative stability, lubricity, flash point, cold flow properties, sulfur contents and acid value were comparable with those of ASTM D 6751 and EN 14214, where applicable. It was concluded that okra seed oil is an acceptable feedstock for biodiesel production. (author)

Non-Edible Plant Oils as New Sources for Biodiesel Production

Directory of Open Access Journals (Sweden)

M. Rafiqul Islam

2008-02-01

Full Text Available Due to the concern on the availability of recoverable fossil fuel reserves and the environmental problems caused by the use those fossil fuels, considerable attention has been given to biodiesel production as an alternative to petrodiesel. However, as the biodiesel is produced from vegetable oils and animal fats, there are concerns that biodiesel feedstock may compete with food supply in the long-term. Hence, the recent focus is to find oil bearing plants that produce non-edible oils as the feedstock for biodiesel production. In this paper, two plant species, soapnut (Sapindus mukorossi and jatropha (jatropha curcas, L. are discussed as newer sources of oil for biodiesel production. Experimental analysis showed that both oils have great potential to be used as feedstock for biodiesel production. Fatty acid methyl ester (FAME from cold pressed soapnut seed oil was envisaged as biodiesel source for the first time. Soapnut oil was found to have average of 9.1% free FA, 84.43% triglycerides, 4.88% sterol and 1.59% others. Jatropha oil contains approximately 14% free FA, approximately 5% higher than soapnut oil. Soapnut oil biodiesel contains approximately 85% unsaturated FA while jatropha oil biodiesel was found to have approximately 80% unsaturated FA. Oleic acid was found to be the dominant FA in both soapnut and jatropha biodiesel. Over 97% conversion to FAME was achieved for both soapnut and jatropha oil.

Pengolahan Biodiesel dari Biji Nyamplung (Calophyllum Inophyllum L Dengan Cara Purifikasi Kering

Directory of Open Access Journals (Sweden)

Rizal Alamsyah

2012-10-01

Full Text Available Tanaman nyamplung atau hutaulo merupakan tanaman yang tumbuh di banyak tempat di Indonesia. Tanaman ini menghasilkan biji yang mempunyai kadar minyak yang tinggi dan dapat diubah menjadi biodiesel. Salah satu masalah dalam proses purifikasi (pencucian biodiesel kasar adalah kebutuhan air dan energi yang tinggi untuk pemanasan air tersebut. Tujuan penelitian ini adalah untuk melakukan purifikasi/pencucian kering biodiesel dan menggantikan metode pencucian dengan air dan proses pengeringan. Percobaan dilakukan dengan mereaksikan minyak nyamplung dengan metanol (MeOH pada suhu 65oC menggunakan katalis NaOH 1% dari berat minyak. Rasio molar minyak nyamplung dan metanol adalah 1 : 11,5. Pencucian kering biodiesel kasar dilakukan dengan penambahan cleaning agent (CA, arang aktif (AA, dan campuran cleaning agent dan arang aktif (AACA. Pencucian kering dilakukan dengan mereaksikan biodiesel kasar dengan CA (1%, 3%, dan 5%, AA (1%, 3%, dan 5%, AACA (1%, 3%, dan 5% dilanjutkan dengan penyaringan vakum. Hasil percobaan menunjukkan bahwa penambahan campuran CA dan AA (5% ke dalam biodiesel menunjukkan hasil terbaik dalam memperoleh kandungan fatty acid methyl ester (FAME sesuai SNI sebesar 96,5%. 

Production of Biodiesel from Waste Vegetable Oil via KM Micromixer

Directory of Open Access Journals (Sweden)

M. F. Elkady

2015-01-01

Full Text Available The production of biodiesel from waste vegetable oils through its pretreatment followed by transesterification process in presence of methanol was investigated using a KM micromixer reactor. The parameters affecting biodiesel production process such as alcohol to oil molar ratio, catalyst concentration, the presence of tetrahydrofuran (THF as a cosolvent, and the volumetric flow rates of inlet fluids were optimized. The properties of the produced biodiesel were compared with its parent waste oil through different characterization techniques. The presence of methyl ester groups at the produced biodiesel was confirmed using both the gas chromatography-mass spectrometry (GC-MS and the infrared spectroscopy (FT-IR. Moreover, the thermal analysis of the produced biodiesel and the comparable waste oil indicated that the product after the transesterification process began to vaporize at 120°C which makes it lighter than its parent oil which started to vaporize at around 300°C. The maximum biodiesel production yield of 97% was recorded using 12 : 1 methanol to oil molar ratio in presence of both 1% NaOH and THF/methanol volume ratio 0.3 at 60 mL/h flow rate.

21 CFR 172.225 - Methyl and ethyl esters of fatty acids produced from edible fats and oils.

Science.gov (United States)

2010-04-01

... from edible fats and oils. 172.225 Section 172.225 Food and Drugs FOOD AND DRUG ADMINISTRATION... Methyl and ethyl esters of fatty acids produced from edible fats and oils. Methyl esters and ethyl esters of fatty acids produced from edible fats and oils may be safely used in food, subject to the...

Efficient 'One Pot' Nitro Reduction-Protection of γ-Nitro Aliphatic Methyl Esters

OpenAIRE

Díaz-Coutiño, Francisco D.; Escalante, Jaime

2009-01-01

A simple and efficient protocol has been developed for the direct conversion of γ-nitro aliphatic methyl esters to N-(tert-butoxycarbonyl)amine methyl esters using NH4+HCO2- and Pd/C in the presence of (Boc)2O. There was a significant decrease in the reaction time under these conditions, increased yields and the purity of the products using this 'one pot' procedure. Un protocolo simple y eficiente de síntesis ha sido desarrollado para la conversión directa de metil ésteres de γ-nitro alifá...

Mackerel biodiesel production from the wastewater containing fish oil

International Nuclear Information System (INIS)

Wu, Y.P.; Huang, H.M.; Lin, Y.F.; Huang, W.D.; Huang, Y.J.

2014-01-01

Marine fish such as mackerel are important for coastal fisheries in Taiwan. Nearly 60,000 tons of mackerel are produced in Suao, I-lan, Taiwan every year. In this study, oil from the discarded parts of mackerel fish contained in wastewater stream were used as the raw material to produce biodiesel through transesterification reaction. The major fuel properties of MB (mackerel biodiesel), including the iodine value, dynamic viscosity, flash point, and heat value, were determined and compared with sunflower seed oil methyl ester (SFM), JCB (Jatropha curcas biodiesel), and premium diesel (D). MB had a higher iodine value, dynamic viscosity, density, and flash point, but a lower heat value, than did D. MB was also used as fuel in a regular diesel engine to verify its emission characteristics. The MB fuel used for exhaust emission test included pure MB (MB100) and a 20% MB blend with premium diesel (MB20). The exhaust emission of MB was also compared with the exhaust emissions of D and JCB. The results showed that MB20 provided a significant reduction in NO, NO x , and SO 2 emissions under varied engine loads, and required no engine modification. - Highlights: • Biodiesel was produced from wastewater containing mackerel fish oil. • Mackerel biodiesel is compared with Jatropha biodiesel and sunflower seed biodiesel. • MBE (mackerel biodiesel) was found to contain higher amount of unsaturated fatty acids. • Mackerel biodiesel, diesel, and Jatropha biodiesel emissions are compared

Rheological behavior, chemical and physical characterization of soybean and cottonseed methyl esters submitted to thermal oxidation process

Energy Technology Data Exchange (ETDEWEB)

Silva, Adriano Sant' ana; Silva, Flavio Luiz Honorato da; Lima, Ezenildo Emanuel de; Carvalho, Maria Wilma N.C. [Universidade Federal de Campina Grande (CCT/UFCG), PB (Brazil). Centro de Ciencia e Tecnologia; Dantas, Hemeval Jales; Farias, Paulo de Almeida [Universidade Federal de Campina Grande (CTRN/UFCG), PB (Brazil). Centro de Tecnologia e Recursos Naturais

2008-07-01

In this study the effect of antioxidant terc-butylhydroxyanisol (BHA) on the oxidative stability of soybean and cottonseed methyl esters subjected to thermal degradation at 100 deg C was studied. Soybean and cottonseed methyl esters specific mass, dynamic viscosity and rheological behavior were evaluated. According to results, antioxidant degraded samples specific mass and dynamic viscosity did not showed alterations, remaining statistically equal. Soybean and cottonseed methyl esters showed a Newtonian rheological behavior and degraded samples without adding BHA showed rheological behavior alterations. (author)

Analysis of performance and emissions of diesel engine using sunflower biodiesel

Science.gov (United States)

Tutunea, Dragos; Dumitru, Ilie

2017-10-01

The world consumption of fossil fuels is increasing rapidly and it affects the environment by green house gases causing health hazards. Biodiesel is emerging as an important promising alternative energy resource which can be used to reduce or even replace the usage of petroleum. Since is mainly derived from vegetable oil or animal fats can be produce for large scale by local farmers offering a great choice. However the extensive utilization of the biofuels can lead to shortages in the food chain. This paper analyzed the sunflower methyl ester (SFME) and its blends as an alternate source of fuel for diesel engines. Biodiesel was prepared from sunflower oil in laboratory in a small biodiesel installation (30L) by base transesterification. A 4 cylinder Deutz F4L912 diesel engine was used to perform the tests on various blends of sunflower biodiesel. The emissions of CO, HC were lower than diesel fuel for all blends tested. The NOx emissions were higher due to the high volatility and high viscosity of biodiesel.

Potentiation of insulin release in response to amino acid methyl esters correlates to activation of islet glutamate dehydrogenase activity

DEFF Research Database (Denmark)

Kofod, Hans; Lernmark, A; Hedeskov, C J

1986-01-01

Column perifusion of mouse pancreatic islets was used to study the ability of amino acids and their methyl esters to influence insulin release and activate islet glutamate dehydrogenase activity. In the absence of L-glutamine, L-serine and the methyl ester of L-phenylalanine, but neither L...... glutamate dehydrogenase activity showed that only the two methyl esters of L-phenylalanine and L-serine activated the enzyme. It is concluded that the mechanism by which methyl esters of amino acids potentiate insulin release is most likely to be mediated by the activation of pancreatic beta-cell glutamate...

Extraction of brewer's yeasts using different methods of cell disruption for practical biodiesel production.

Science.gov (United States)

Řezanka, Tomáš; Matoulková, Dagmar; Kolouchová, Irena; Masák, Jan; Viden, Ivan; Sigler, Karel

2015-05-01

The methods of preparation of fatty acids from brewer's yeast and its use in production of biofuels and in different branches of industry are described. Isolation of fatty acids from cell lipids includes cell disintegration (e.g., with liquid nitrogen, KOH, NaOH, petroleum ether, nitrogenous basic compounds, etc.) and subsequent processing of extracted lipids, including analysis of fatty acid and computing of biodiesel properties such as viscosity, density, cloud point, and cetane number. Methyl esters obtained from brewer's waste yeast are well suited for the production of biodiesel. All 49 samples (7 breweries and 7 methods) meet the requirements for biodiesel quality in both the composition of fatty acids and the properties of the biofuel required by the US and EU standards.

Study of fuel properties of rubber seed oil based biodiesel

International Nuclear Information System (INIS)

Ahmad, Junaid; Yusup, Suzana; Bokhari, Awais; Kamil, Ruzaimah Nik Mohammad

2014-01-01

Graphical abstract: - Highlights: • This article presents the comparative studies of the fuel properties of rubber seed oil based biodiesel. • The design expert has been adopted for the optimization of the process variables. • The FTIR, cold flow properties and oxidation stability are the findings of present study. • All the fuel properties met the standards such as ASTM D6751 and EN 14214. • Present study reveals that rubber seed oil as a non-edible source potentially contributes for esters production. - Abstract: The scarcity of the fossil fuel, environmental pollution and food crisis are the world’s major issues in current era. Biodiesel is an alternative to diesel fuel, environment friendly and biodegradable and is produced from either edible or non-edible oils. In this study, a non-edible rubber seed oil (RSO) with high free fatty acid (FFA) content of 45% were used for the production of biodiesel. The process comprises of two steps. The first step is the acid esterification to reduce the FFA value and the second step is the base transesterification. The response surface methodology (RSM) was used for parametric optimization of the two stage processes i.e. acid esterification and base transesterification. The yield of biodiesel was analyzed using gas chromatography. The FTIR (Fourier Transform Infra-Red) spectrum was also determined to confirm the conversion of fatty acid to methyl esters. The fuel properties were analyzed according to the ASTM D6751 and EN14214 and were compared with the previous finding of researchers. All analyzed properties fulfilled the biodiesel standard criteria

Process intensification of catalytic liquid-liquid solid processes : Continuous biodiesel production using an immobilized lipase in a centrifugal contactor separator

NARCIS (Netherlands)

Ilmi, M.; Kloekhorst, A.; Winkelman, J. G. M.; Euverink, G. J. W.; Hidayat, C.; Heeres, H. J.

Biodiesel or fatty acid methyl ester (FAME) synthesis from sunflower oil and methanol using an immobilized lipase, an example of a liquid-liquid solid reaction, was studied in batch and various continuous reactor set-ups including the use of a centrifugal contactor separator (CCCS). The latter is an

Emission Characteristics of CI Engine by using Palm BioDiesel

OpenAIRE

V.S.shai sundaram; S.S.shai monish

2015-01-01

Environmental concerns and energy crisis of the world has led to the search of alternate to the fossil fuel. FAME (Fatty Acid Methyl Ester) is environment friendly, alternative, and non-toxic, safe; biodegradable has a high flash point and is also termed as Bio-Diesel. The growing economic risk of relying primarily on fossil fuels with limited reserves and Increasing prices has increased the interest on alternative energy sources. Clean and renewable biofuels have been touted as t...

Efficacy of fatty acid profile as a tool for screening feedstocks for biodiesel production

International Nuclear Information System (INIS)

Moser, Bryan R.; Vaughn, Steven F.

2012-01-01

Fuel properties are largely dependent on the fatty acid (FA) composition of the feedstock from which biodiesel is prepared. Consequently, FA profile was employed as a screening tool for selection of feedstocks high in monounsaturated FAs for further evaluation as biodiesel. Those feedstocks included ailanthus (Ailanthus altissima L.), anise (Pimpinella anisum L.), arugula (Eruca vesicaria L.), cress (Lepidium sativum L.), cumin (Cuminum cyminum L.), Indian cress (Tropaeolum majus L.), shepherd’s purse (Capsella bursa-pastoris L.) and upland cress (Barbarea verna (Mill.) Asch.). Other selection criteria included saturated FA content, iodine value (IV), content of FAs containing twenty or more carbons and content of trienoic FAs. Anise oil satisfied all selection criteria and was therefore selected for further investigation. Arugula, cumin and upland cress oils were selected as antagonists to the selection criteria. Preparation of FA methyl esters (FAMEs, ≥ 92 wt % yield) following conventional alkaline-catalyzed methanolysis preceded fuel property determination. Of particular interest were oxidative stability and cold flow properties. Also measured were kinematic viscosity (40 °C), IV, acid value, free and total glycerol content, sulfur and phosphorous content, cetane number, energy content and lubricity. FAMEs prepared from anise oil yielded properties compliant with biodiesel standards ASTM D6751 and EN 14214 whereas the antagonists failed at least one specification contained within the standards. As a result, FA profile was an efficient predictor of compliance with biodiesel standards and is therefore recommended as a screening tool for investigation of alternative feedstocks. -- Highlights: ► Fatty acid methyl esters were prepared from several alternative feedstocks. ► Fatty acid composition was a principal factor influencing fuel properties. ► Oxidative stability and cold flow properties of biodiesel were examined in detail. ► Limits were developed

Production of biodiesel from vegetable oils

Directory of Open Access Journals (Sweden)

Luque, Susana

2008-03-01

Full Text Available Biodiesel is produced by transesterification of triglycerides present in animal fat or vegetable oils, by displacing glycerine with a low molar mass alcohol. This resulting ester mixture has physico-chemical properties similar to those of petroleum diesel. This paper reviews the synthetic paths that lead to biodiesel by means of the catalytic transesterification of vegetable oils. Although methyl esters are at present the only ones produced at industrial scale, the use of ethanol, which can also be obtained from renewable resources, has been considered, since it would generate a cleaner and more biocompatible fuel.El biodiésel se produce mediante la transesterificación de triglicéridos, presentes en grasas animales o aceites vegetales, en un proceso en el que un alcohol de bajo peso molecular desplaza a la glicerina. La mezcla de esteres así resultante posee unas propiedades físico-químicas similares a las del diésel procedente de petróleo. En este artículo se revisan las vías de síntesis de biodiésel mediante la transesterificación catalítica de aceites vegetales. Aunque actualmente a escala industrial solo se producen ésteres metílicos, también se ha considerado el uso de etanol, ya que éste se obtiene también de fuentes renovables, generando así un combustible más limpio y biocompatible.

Analysis of biodiesel and biodiesel-petrodiesel blends by high performance thin layer chromatography combined with easy ambient sonic-spray ionization mass spectrometry.

Science.gov (United States)

Eberlin, Livia S; Abdelnur, Patricia V; Passero, Alan; de Sa, Gilberto F; Daroda, Romeu J; de Souza, Vanderlea; Eberlin, Marcos N

2009-08-01

High performance thin layer chromatography (HPTLC) combined with on-spot detection and characterization via easy ambient sonic-spray ionization mass spectrometry (EASI-MS) is applied to the analysis of biodiesel (B100) and biodiesel-petrodiesel blends (BX). HPTLC provides chromatographic resolution of major components whereas EASI-MS allows on-spot characterization performed directly on the HPTLC surface at ambient conditions. Constituents (M) are detected by EASI-MS in a one component-one ion fashion as either [M + Na](+) or [M + H](+). For both B100 and BX samples, typical profiles of fatty acid methyl esters (FAME) detected as [FAME + Na](+) ions allow biodiesel typification. The spectrum of the petrodiesel spot displays a homologous series of protonated alkyl pyridines which are characteristic for petrofuels (natural markers). The spectrum for residual or admixture oil spots is characterized by sodiated triglycerides [TAG + Na](+). The application of HPTLC to analyze B100 and BX samples and its combination with EASI-MS for on-spot characterization and quality control is demonstrated.

Obtention and characterization of biodiesel; Obtencao e caracterizacao do biodiesel

Energy Technology Data Exchange (ETDEWEB)

Santos, Leonidas B.O. dos; Caitano, Moises; Aranda, Donato A.G.; Mothe, Cheila G. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil)

2004-07-01

Biodiesel is an ester resulting from the transesterification reaction of an alcohol and an oil obtained from biomass. The products of the transesterification are an ester and the glycerol. The biodiesel and the petroleum commercial diesel have similar properties, and they can be mixed and used in diesel motors. The use of biodiesel will allow a better exploration of the energetic potential of our cultures. The biodiesel has some advantages compared to others combustibles, such as adaptability to usual diesel motors and non-generation of NO{sub x} and SO{sub x} compounds. Many experiments with biodiesel have been made in Brazil since the 70's. This work made samples of biodiesel by transesterification batch reactions to many blends of soybean oil and residual fry oil, at room temperature, using mechanical mixture or magnetic agitation by a magnetic stirrer, using as catalysts sodium methoxide and potassium hydroxide. For each obtained sample tests to determine the Acidity Index (ABNT-MB-74), Saponification Index (ABNT-MB-75), Iodine Wijz Index (ABNT-MB- 77), thermal analysis by DTA and TG (TA Instruments SDT 2960, 30 to 800 deg C, 10 deg C/min at nitrogen atmosphere) and rheological test (Haake RS 150 Rheo Stress rheometer) were done. (author)

Artificial Neural Network Approach to Predict Biodiesel Production in Supercritical tert-Butyl Methyl Ether

Directory of Open Access Journals (Sweden)

Obie Farobie

2016-05-01

Full Text Available In this study, for the first time artificial neural network was used to predict biodiesel yield in supercritical tert-butyl methyl ether (MTBE. The experimental data of biodiesel yield conducted by varying four input factors (i.e. temperature, pressure, oil-to-MTBE molar ratio, and reaction time were used to elucidate artificial neural network model in order to predict biodiesel yield. The main goal of this study was to assess how accurately this artificial neural network model to predict biodiesel yield conducted under supercritical MTBE condition. The result shows that artificial neural network is a powerful tool for modeling and predicting biodiesel yield conducted under supercritical MTBE condition that was proven by a high value of coefficient of determination (R of 0.9969, 0.9899, and 0.9658 for training, validation, and testing, respectively. Using this approach, the highest biodiesel yield was determined of 0.93 mol/mol (corresponding to the actual biodiesel yield of 0.94 mol/mol that was achieved at 400 °C, under the reactor pressure of 10 MPa, oil-to-MTBE molar ratio of 1:40 within 15 min of reaction time.

Catalyst technology for biofuel production: Conversion of renewable lipids into biojet and biodiesel

Directory of Open Access Journals (Sweden)

Scharff Yves

2013-09-01

Full Text Available Renewable lipids based biofuels are an important tool to address issues raised by policies put in place in order to reduce the dependence of transportation sector on fossil fuels and to promote the development of non-food based, sustainable and eco-friendly fuels. This paper presents the main features of the heterogeneous catalysis technologies Axens has developed for the production of biofuels from renewable lipids: the first by transesterification to produce fatty acid methyl esters or biodiesel and the second by hydrotreating to produce isoparaffinic hydroprocessed ester and fatty acids, high blending rate drop-in diesel and jet biofuels.

Oxidative stability of biodiesels produced from vegetable oils having different degrees of unsaturation

International Nuclear Information System (INIS)

Pantoja, Samantha Siqueira; Conceição, Leyvison Rafael V. da; Costa, Carlos E.F. da; Zamian, José R.; Rocha Filho, Geraldo N. da

2013-01-01

Highlights: • We obtained biodiesel from açai, cupuaçu, passion fruit and linseed oil. • Determined the properties of biodiesel, such as kinematic viscosity, cold filter plugging point and oxidative stability. • Evaluated the influence of antioxidants on biodiesel. • The PG antioxidant was more efficient than BHA and TBHQ for the açaí biodiesel. - Abstract: In the present paper, methyl esters were obtained from the transesterification of cupuaçu fat lipids (Theobroma grandiflorum) (Willd. ex Spreng.) (K. Schum.), açaí (Euterpe oleracea), passion fruit (Passiflora edulis) and linseed (Linum usitatissimum L.) oils, using a basic catalyst. The triglycerides were characterized by their fatty acid composition, and the biodiesels were characterized according to standard methods. The critical properties, such as the cold filter plugging point, kinematic viscosity and oxidative stability, of the biodiesels were studied. The influence of butyl-hydroxyanisole (BHA), propyl gallate (PG) and tert-butyl hydroquinone (TBHQ) antioxidants on the açaí, passion fruit and linseed biodiesels was evaluated at concentrations from 500 to 4000 ppm. PG was found to be the most efficient antioxidant for the studied biodiesels

Biodiesel production and marketing in Germany. The situation and perspective; Biodieselproduktion und Vermarktung in Deutschland. Situation und Perspektive

Energy Technology Data Exchange (ETDEWEB)

Bockey, D.

2002-07-01

Out of all the renewable raw material products, Biodiesel is by far the most important for German agriculture. Now after 12 years of intensive product assessment by UFOP and its member federations, Biodiesel made from rapeseed oil is beginning to establish itself as a technically developed alternative in the fuel market. For the practical use of alternative fuels practically only pure Biodiesel fulfills the set requirements. While the UFOP essentially financed and carried out public relations and sales promotion measures etc., the vehicle industry and Biodiesel manufacturers developed the technical and normative prerequisites for lasting market entry for rapeseed oil methyl esters. This could not have been done without financial support from the federal state governments, the Federal Government and the European Union.

Gas chromatography-vacuum ultraviolet spectroscopy for analysis of fatty acid methyl esters.

Science.gov (United States)

Fan, Hui; Smuts, Jonathan; Bai, Ling; Walsh, Phillip; Armstrong, Daniel W; Schug, Kevin A

2016-03-01

A new vacuum ultraviolet (VUV) detector for gas chromatography was recently developed and applied to fatty acid methyl ester (FAME) analysis. VUV detection features full spectral acquisition in a wavelength range of 115-240nm, where virtually all chemical species absorb. VUV absorption spectra of 37 FAMEs, including saturated, monounsaturated, and polyunsaturated types were recorded. Unsaturated FAMEs show significantly different gas phase absorption profiles than saturated ones, and these classes can be easily distinguished with the VUV detector. Another advantage includes differentiating cis/trans-isomeric FAMEs (e.g. oleic acid methyl ester and linoleic acid methyl ester isomers) and the ability to use VUV data analysis software for deconvolution of co-eluting signals. As a universal detector, VUV also provides high specificity, sensitivity, and a fast data acquisition rate, making it a powerful tool for fatty acid screening when combined with gas chromatography. The fatty acid profile of several food oil samples (olive, canola, vegetable, corn, sunflower and peanut oils) were analyzed in this study to demonstrate applicability to real world samples. Copyright © 2015 Elsevier Ltd. All rights reserved.

Particulate filter behaviour of a Diesel engine fueled with biodiesel

International Nuclear Information System (INIS)

Buono, D.; Senatore, A.; Prati, M.V.

2012-01-01

Biodiesel is an alternative and renewable fuel made from plant and animal fat or cooked oil through a transesterification process to produce a short chain ester (generally methyl ester). Biodiesel fuels have been worldwide studied in Diesel engines and they were found to be compatible in blends with Diesel fuel to well operate in modern Common Rail engines. Also throughout the world the diffusion of biofuels is being promoted in order to reduce greenhouse gas emissions and the environmental impact of transport, and to increase security of supply. To meet the current exhaust emission regulations, after-treatment devices are necessary; in particular Diesel Particulate Filters (DPFs) are essential to reduce particulate emissions of Diesel engines. A critical requirement for the implementation of DPF on a modern Biodiesel powered engine is the determination of Break-even Temperature (BET) which is defined as the temperature at which particulate deposition on the filter is balanced by particulate oxidation on the filter. To fit within the exhaust temperature range of the exhaust line and to require a minimum of active regeneration during the engine running, the BET needs to occur at sufficiently low temperatures. In this paper, the results of an experimental campaign on a modern, electronic controlled fuel injection Diesel engine are shown. The engine was fuelled either with petroleum ultralow sulphur fuel or with Biodiesel: BET was evaluated for both fuels. Results show that on average, the BET is lower for biodiesel than for diesel fuel. The final goal was to characterize the regeneration process of the DPF device depending on the adopted fuel, taking into account the different combustion process and the different nature of the particulate matter. Overall the results suggest significant benefits for the use of biodiesel in engines equipped with DPFs. - Highlights: ► We compare Diesel Particulate Trap (DPF) performance with Biodiesel and Diesel fuel. ► The Break

In-situ transesterification of seeds of invasive Chinese tallow trees (Triadica sebifera L.) in a microwave batch system (GREEN(3)) using hexane as co-solvent: Biodiesel production and process optimization.

Science.gov (United States)

Barekati-Goudarzi, Mohamad; Boldor, Dorin; Nde, Divine B

2016-02-01

In-situ transesterification (simultaneous extraction and transesterification) of Chinese tallow tree seeds into methyl esters using a batch microwave system was investigated in this study. A high degree of oil extraction and efficient conversion of oil to biodiesel were found in the proposed range. The process was further optimized in terms of product yields and conversion rates using Doehlert optimization methodology. Based on the experimental results and statistical analysis, the optimal production yield conditions for this process were determined as: catalyst concentration of 1.74wt.%, solvent ratio about 3 (v/w), reaction time of 20min and temperature of 58.1°C. H(+)NMR was used to calculate reaction conversion. All methyl esters produced using this method met ASTM biodiesel quality specifications. Copyright © 2015 Elsevier Ltd. All rights reserved.

Fast Synthesis of High Quality Biodiesel from ‘Waste Fish Oil’ by Single Step Transesterification

Directory of Open Access Journals (Sweden)

Yogesh C. Sharma

2014-09-01

Full Text Available A large volume of fish wastes is produced on a daily basis in the Indian sub-continent. This abundant waste source could serve as an economic feedstock for bioenergy generation. In the present study, oil extracted from discarded fish parts was used for high quality biodiesel production. More specifically, a single step transesterification of ‘waste fishoil’ with methanol using sodium methoxide (CH3ONa as homogeneous catalyst under moderate operational conditions resulted in highly pure biodiesel of > 98% of fatty acid methyl ester (FAME content. Characterization was performed by Fourier Transform-Nuclear Magnetic Resonance (FT-NMR.

Simulation of biodiesel production using hydro-esterification process from wet microalgae

Directory of Open Access Journals (Sweden)

Pradana Yano Surya

2018-01-01

Full Text Available Recently, algae have received a lot of attention as a new biomass source for the production of renewable energy, such as biodiesel. Conventionally, biodiesel is made through esterification or transesterification of oils where the process involves a catalyst and alcohol to be reacted in a reactor. However, this process is energy intensive for drying and extraction step. To overcome this situation, we studied simulation of a new route of hydro-esterification process which is combine hydrolysis and esterification processes for biodiesel production from wet microalgae. Firstly, wet microalgae treated by hydrolyzer to produce fatty acids (FAs, separated with separator, and then mixed with methanol and esterified at subcritical condition to produce fatty acid methyl esters (FAMEs while H2SO4 conducted as the catalyst. Energy and material balance of conventional and hydrolysis-esterification process was evaluated by Aspen Plus. Simulation result indicated that conventional route is energy demanding process, requiring 4.40 MJ/L biodiesel produced. In contrast, the total energy consumption of hydrolysis-esterification method can be reduced significantly into 2.43 MJ/L biodiesel. Based on the energy consumption comparison, hydro-esterification process is less costly than conventional process for biodiesel production.

Potential plant oil feedstock for lipase-catalyzed biodiesel production in Thailand

International Nuclear Information System (INIS)

Winayanuwattikun, Pakorn; Kaewpiboon, Chutima; Piriyakananon, Kingkaew; Tantong, Supalak; Thakernkarnkit, Weerasak; Chulalaksananukul, Warawut; Yongvanich, Tikamporn

2008-01-01

Twenty-seven types of plants found to contain more than 25% of oil (w/w) were selectively examined from 44 species. Saponification number (SN), iodine value (IV), cetane number (CN) and viscosity (η) of fatty acid methyl esters (FAMEs) of oils were empirically determined, and they varied from 182 to 262, 3.60 to 142.70, 39.32 to 65.80 and 2.29 to 3.95, respectively. Fatty acid compositions, IV, CN and η were used to predict the quality of FAMEs for use as biodiesel. FAMEs of plant oils of 15 species were found to be most suitable for use as biodiesel by meeting the major specification of biodiesel standards of Thailand, USA and European Standard Organization. The oils from these 15 species were further investigated for the conversion efficiency of biodiesel in lipase-catalyzed transesterification reaction with Novozyme 435 and Lipozyme RM IM. Oils of four species, palm (Elaeis guineensis), physic nut (Jatropha curcas), papaya (Carica papaya) and rambutan (Nephelium lappaceum), can be highly converted to biodiesel by transesterification using Novozyme 435- or Lipozyme RM IM-immobilized lipase as catalyst. Therefore, these selected plants would be economically considered as the feedstock for biodiesel production by biocatalyst

Biodiesel production via the transesterification of soybean oil using waste starfish (Asterina pectinifera).

Science.gov (United States)

Jo, Yong Beom; Park, Sung Hoon; Jeon, Jong-Ki; Ko, Chang Hyun; Ryu, Changkook; Park, Young-Kwon

2013-07-01

Calcined waste starfish was used as a base catalyst for the production of biodiesel from soybean oil for the first time. A batch reactor was used for the transesterification reaction. The thermal characteristics and crystal structures of the waste starfish were investigated by thermo-gravimetric analysis and X-ray diffraction. The biodiesel yield was determined by measuring the content of fatty acid methyl esters (FAME). The calcination temperature appeared to be a very important parameter affecting the catalytic activity. The starfish-derived catalyst calcined at 750 °C or higher exhibited high activity for the transesterification reaction. The FAME content increased with increasing catalyst dose and methanol-over-oil ratio.

Biodiesel production from wet municipal sludge: evaluation of in situ transesterification using xylene as a cosolvent.

Science.gov (United States)

Choi, O K; Song, J S; Cha, D K; Lee, J W

2014-08-01

This study proposes a method to produce biodiesel from wet wastewater sludge. Xylene was used as an alternative cosolvent to hexane for transesterification in order to enhance the biodiesel yield from wet wastewater sludge. The water present in the sludge could be separated during transesterification by employing xylene, which has a higher boiling point than water. Xylene enhanced the biodiesel yield up to 8.12%, which was 2.5 times higher than hexane. It was comparable to the maximum biodiesel yield of 9.68% obtained from dried sludge. Xylene could reduce either the reaction time or methanol consumption, when compared to hexane for a similar yield. The fatty acid methyl esters (FAMEs) content of the biodiesel increased approximately two fold by changing the cosolvent from hexane to xylene. The transesterification method using xylene as a cosolvent can be applied effectively and economically for biodiesel recovery from wet wastewater sludge without drying process. Copyright © 2014 Elsevier Ltd. All rights reserved.

Biodiesel production from Norouzak (Salvia lerifolia) seeds as an indigenous source of bio fuel in Iran using ultrasound

International Nuclear Information System (INIS)

Hajinezhad, Ahmad; Abedi, Sepideh; Ghobadian, Barat; Noorollahi, Younes

2015-01-01

Highlights: • Salvia lerifolia seed oil is introduced as an indigenous source of biodiesel production in Iran. • Biodiesel was obtained from the samples by basic trans-esterification method using ultrasounds device. • Norouzak oil profile was extracted based on BF3 method, and it was determined by Gas Chromatography (GC) and Metcalf method. • The produced biodiesel characteristics from Norouzak oil seed is suitable for use in CI engines with low air pollutions. - Abstract: Population growth with increased demand for fossil fuels and also significant increases in air pollution has confirmed necessity of using alternative fuels such as biodiesel. In this paper, Norouzak (Salvia lerifolia) seed oil is introduced as an indigenous source of biodiesel production in Iran. The seeds were collected from desert area of South Khorasan province Northeastern-Iran. In this regards, kinematic and dynamic viscosity, density, amount of free fatty acids, soap value, acid value and water content of the Noruzak oil are measured which are 28.435 (mP s), 31.433 (mm 2 /s), 0.9046 (g/cm 2 ), 0.71%, 160.25 (mg/1 g), 1.4139 (mg) and 0/3% respectively. Also, fatty acid methyl esters C 16:0 , C 16:1 , C 18:0 , C 18:1 , C 18:1c , C 18:2 , C 18:2c , C 18:3 , C 20 , C 20:1 , C 22 , C 22:1 , C 24 , C 24:1 are known by Gas Chromatography (GC) and BF 3 method which results shows C 18:2 (40.8%) and C 18:1 (24) have the highest proportion of methyl ester in this oil. Norouzak biodiesel was obtained by basic trans-esterification method using ultrasounds device as a new sustainable and environmentally-friendly green technique under ultrasonic amplitude of 60% and 9 min at 45 °C, with methanol ratio of 1:5, 1:6, 1:7 and 1% potassium hydroxide as catalyst. The results showed that there is maximum performance of methyl ester production (97.60) with methanol molar ratio of 1:6 which shows significant improvement in the bio fuel production yield using ultrasound technology under the operating

Biodegradation of biodiesel fuels

International Nuclear Information System (INIS)

Zhang, X.; Haws, R.; Wright, B.; Reese, D.; Moeller, G.; Peterson, C.

1995-01-01

Biodiesel fuel test substances Rape Ethyl Ester (REE), Rape Methyl Ester (RME), Neat Rape Oil (NR), Say Methyl Ester (SME), Soy Ethyl Ester (SEE), Neat Soy Oil (NS), and proportionate combinations of RME/diesel and REE/diesel were studied to test the biodegradability of the test substances in an aerobic aquatic environment using the EPA 560/6-82-003 Shake Flask Test Method. A concurrent analysis of Phillips D-2 Reference Diesel was also performed for comparison with a conventional fuel. The highest rates of percent CO 2 evolution were seen in the esterified fuels, although no significant difference was noted between them. Ranges of percent CO 2 evolution for esterified fuels were from 77% to 91%. The neat rape and neat soy oils exhibited 70% to 78% CO 2 evolution. These rates were all significantly higher than those of the Phillips D-2 reference fuel which evolved from 7% to 26% of the organic carbon to CO 2 . The test substances were examined for BOD 5 and COD values as a relative measure of biodegradability. Water Accommodated Fraction (WAF) was experimentally derived and BOD 5 and COD analyses were carried out with a diluted concentration at or below the WAF. The results of analysis at WAF were then converted to pure substance values. The pure substance BOD 5 and COD values for test substances were then compared to a control substance, Phillips D-2 Reference fuel. No significant difference was noted for COD values between test substances and the control fuel. (p > 0.20). The D-2 control substance was significantly lower than all test substances for BCD, values at p 5 value

Synthesis of [11C]-labelled methyl esters: transesterification of enol esters versus BF3 etherate catalysed esterification - a comparative study

International Nuclear Information System (INIS)

Ackermann, U.; Falzon, C.; Issa, W.; Tochon-Danguy, H.J.; Sachinidis, J.I.; Blanc, P.; White, J.; Scott, A.M.

2005-01-01

An important issue in Positron Emission Tomography (PET) is the development of labelling techniques to incorporate positron emitting radionuclides into biologically active compounds. When labelling with 11C, the short 20 minutes half-life of the radionuclide significantly limits the number of synthetic protocols available to the radiochemist. C-l synthons such as [HCJ-methyl iodide (1) or methyl triflate (2) are readily available and are frequently used as alkylating agents for the preparation of radiopharmaceuticals. However, the use of these alkylating agents often makes it necessary to introduce protecting groups in order to prevent labelling at unwanted sites on the molecule. Since the removal of protecting groups is a time-consuming process, a more direct synthesis strategy is desirable. This has prompted us to investigate the esterification of carboxylic acids using [1 lC]-mcthanol and BF3 etherate as Lewis acid catalyst. Our results have demonstrated that the reaction conditions necessary to promote the esterification can cleave functional groups such as ethers. We have therefore shifted our attention towards the irreversible transesterification of enol esters using [HCl-methanol and a tin catalyst as an alternative strategy to [HC]-methyl ester formation. We have prepared a series of 5 aromatic ethoxy vinyl esters bearing various functional groups. The transesterification (radiolabelling) was carried out in DMSO at 150 Degrees C for 7 minutes in the presence of [HQMeOH and 1.3-dichlo-rotetrabutyldistannoxane as catalyst. We have found that the transesterification of enol esters is a mild and efficient labelling method for the formation of [HCl-methyl esters. The reaction proceeds smoothly and leaves functional groups intact. It requires only one synthesis step compared to two steps for the conventional method, and gives a radiochemical yields of 25%

Determination and discrimination of biodiesel fuels by gas chromatographic and chemometric methods

Science.gov (United States)

Milina, R.; Mustafa, Z.; Bojilov, D.; Dagnon, S.; Moskovkina, M.

2016-03-01

Pattern recognition method (PRM) was applied to gas chromatographic (GC) data for a fatty acid methyl esters (FAME) composition of commercial and laboratory synthesized biodiesel fuels from vegetable oils including sunflower, rapeseed, corn and palm oils. Two GC quantitative methods to calculate individual fames were compared: Area % and internal standard. The both methods were applied for analysis of two certified reference materials. The statistical processing of the obtained results demonstrates the accuracy and precision of the two methods and allows them to be compared. For further chemometric investigations of biodiesel fuels by their FAME-profiles any of those methods can be used. PRM results of FAME profiles of samples from different vegetable oils show a successful recognition of biodiesels according to the feedstock. The information obtained can be used for selection of feedstock to produce biodiesels with certain properties, for assessing their interchangeability, for fuel spillage and remedial actions in the environment.

Determination and discrimination of biodiesel fuels by gas chromatographic and chemometric methods

Directory of Open Access Journals (Sweden)

Milina R.

2016-03-01

Full Text Available Pattern recognition method (PRM was applied to gas chromatographic (GC data for a fatty acid methyl esters (FAME composition of commercial and laboratory synthesized biodiesel fuels from vegetable oils including sunflower, rapeseed, corn and palm oils. Two GC quantitative methods to calculate individual fames were compared: Area % and internal standard. The both methods were applied for analysis of two certified reference materials. The statistical processing of the obtained results demonstrates the accuracy and precision of the two methods and allows them to be compared. For further chemometric investigations of biodiesel fuels by their FAME-profiles any of those methods can be used. PRM results of FAME profiles of samples from different vegetable oils show a successful recognition of biodiesels according to the feedstock. The information obtained can be used for selection of feedstock to produce biodiesels with certain properties, for assessing their interchangeability, for fuel spillage and remedial actions in the environment.

Experimental investigation of evaporation rate and emission studies of diesel engine fuelled with blends of used vegetable oil biodiesel and producer gas

Directory of Open Access Journals (Sweden)

Nanjappan Balakrishnan

2015-01-01

Full Text Available An experimental study to measure the evaporation rates, engine performance and emission characteristics of used vegetable oil methyl ester and its blends with producer gas on naturally aspirated vertical single cylinder water cooled four stroke single cylinder diesel engine is presented. The thermo-physical properties of all the bio fuel blends have been measured and presented. Evaporation rates of used vegetable oil methyl ester and its blends have been measured under slow convective environment of air flowing with a constant temperature and the values are compared with fossil diesel. Evaporation constants have been determined by using the droplet regression rate data. The fossil diesel, biodiesel blends and producer gas have been utilized in the test engine with different load conditions to evaluate the performance and emission characteristics of diesel engine and the results are compared with each other. From these observations, it could be noted that, smoke and hydrocarbon drastically reduced with biodiesel in the standard diesel engine without any modifications.

Novel fatty acid methyl esters from the actinomycete Micromonospora aurantiaca

Science.gov (United States)

Bruns, Hilke; Riclea, Ramona

2011-01-01

Summary The volatiles released by Micromonospora aurantiaca were collected by means of a closed-loop stripping apparatus (CLSA) and analysed by GC–MS. The headspace extracts contained more than 90 compounds from different classes. Fatty acid methyl esters (FAMEs) comprised the major compound class including saturated unbranched, monomethyl and dimethyl branched FAMEs in diverse structural variants: Unbranched, α-branched, γ-branched, (ω−1)-branched, (ω−2)-branched, α- and (ω−1)-branched, γ- and (ω−1)-branched, γ- and (ω−2)-branched, and γ- and (ω−3)-branched FAMEs. FAMEs of the last three types have not been described from natural sources before. The structures for all FAMEs have been suggested based on their mass spectra and on a retention index increment system and verified by the synthesis of key reference compounds. In addition, the structures of two FAMEs, methyl 4,8-dimethyldodecanoate and the ethyl-branched compound methyl 8-ethyl-4-methyldodecanoate were deduced from their mass spectra. Feeding experiments with isotopically labelled [2H10]leucine, [2H10]isoleucine, [2H8]valine, [2H5]sodium propionate, and [methyl-2H3]methionine demonstrated that the responsible fatty acid synthase (FAS) can use different branched and unbranched starter units and is able to incorporate methylmalonyl-CoA elongation units for internal methyl branches in various chain positions, while the methyl ester function is derived from S-adenosyl methionine (SAM). PMID:22238549

Phytotoxicity of three plant-based biodiesels, unmodified castor oil, and Diesel fuel to alfalfa (Medicago sativa L.), lettuce (Lactuca sativa L.), radish (Raphanus sativus), and wheatgrass (Triticum aestivum).

Science.gov (United States)

Bamgbose, Ifeoluwa; Anderson, Todd A

2015-12-01

The wide use of plant-based oils and their derivatives, in particular biodiesel, have increased extensively over the past decade to help alleviate demand for petroleum products and improve the greenhouse gas emissions profile of the transportation sector. Biodiesel is regarded as a clean burning alternative fuel produced from livestock feeds and various vegetable oils. Although in theory these animal and/or plant derived fuels should have less environmental impact in soil based on their simplified composition relative to Diesel, they pose an environmental risk like Diesel at high concentrations when disposed. The aim of the present study was to ascertain the phytotoxicity of three different plant-derived biodiesels relative to conventional Diesel. For phytotoxicological analysis, we used seeds of four crop plants, Medicago sativa, Lactuca sativa, Raphanus sativus, and Triticum aestivum to analyze the germination of seeds in contaminated soil samples. The toxicological experiment was conducted with two different soil textures: sandy loam soil and silt loam soil. The studied plant-based biodiesels were safflower methyl-ester, castor methyl ester, and castor ethyl-ester. Biodiesel toxicity was more evident at high concentrations, affecting the germination and survival of small-seeded plants to a greater extent. Tolerance of plants to the biodiesels varied between plant species and soil textures. With the exception of R. sativus, all plant species were affected and exhibited some sensitivity to the fuels, such as delayed seedling emergence and slow germination (average=10 days) at high soil concentrations (0.85% for Diesel and 1.76% for the biodiesels). Tolerance of plants to soil contamination had a species-specific nature, and on average, decreased in the following order: Raphanus sativus (0-20%)>Triticum aestivum (10-40%) ≥ Medicago sativa> Lactuca sativa (80-100%). Thus, we conclude that there is some phytotoxicity associated with plant-based biodiesels. Further

Biodiesel production process optimization and characterization to assess the suitability of the product for varied environmental conditions

Energy Technology Data Exchange (ETDEWEB)

Eevera, T.; Rajendran, K.; Saradha, S. [Department of Biotechnology, Periyar Maniammai University, Periyar Nagar, Vallam, Thanjavur, Tamilnadu 613 403 (India)

2009-03-15

In this study, both edible (coconut oil, palm oil, groundnut oil, and rice bran oil) and non-edible oils (pongamia, neem and cotton seed oil) were used to optimize the biodiesel production process variables like catalyst concentration, amount of methanol required for reaction, reaction time and reaction temperature. The fuel properties like specific gravity, moisture content, refractive index, acid value, iodine number, saponification value and peroxide value were estimated. Based on the cetane number and iodine value, the methyl esters obtained from palm and coconut oils were not suitable to use as biodiesel in cold weather conditions, but for hot climate condition biodiesel obtained from the remaining oil sources is suitable. (author)

Experimental investigation on performance and exhaust emissions of castor oil biodiesel from a diesel engine.

Science.gov (United States)

Shojaeefard, M H; Etgahni, M M; Meisami, F; Barari, A

2013-01-01

Biodiesel, produced from plant and animal oils, is an important alternative to fossil fuels because, apart from dwindling supply, the latter are a major source of air pollution. In this investigation, effects of castor oil biodiesel blends have been examined on diesel engine performance and emissions. After producing castor methyl ester by the transesterification method and measuring its characteristics, the experiments were performed on a four cylinder, turbocharged, direct injection, diesel engine. Engine performance (power, torque, brake specific fuel consumption and thermal efficiency) and exhaust emissions were analysed at various engine speeds. All the tests were done under 75% full load. Furthermore, the volumetric blending ratios of biodiesel with conventional diesel fuel were set at 5, 10, 15, 20 and 30%. The results indicate that lower blends of biodiesel provide acceptable engine performance and even improve it. Meanwhile, exhaust emissions are much decreased. Finally, a 15% blend of castor oil-biodiesel was picked as the optimized blend of biodiesel-diesel. It was found that lower blends of castor biodiesel are an acceptable fuel alternative for the engine.

Alkaline catalyzed biodiesel production from moringa oleifera oil with optimized production parameters

Energy Technology Data Exchange (ETDEWEB)

Kafuku, G.; Mbarawa, M. [Department of Mechanical Engineering, Tshwane University of Technology, Private Bag X680, 0001 Pretoria (South Africa)

2010-08-15

The utilization of non-edible feedstock such as moringa oleifera for biodiesel production attracts much attention owing to the issue with regards to avoiding a threat to food supplies. In this study, the optimization of biodiesel production parameters for moringa oleifera oil was carried out. The free fatty acid value of moringa oil was found to be 0.6%, rendering the one step alkaline transesterification method for converting moringa fatty acids to their methyl esters possible. The optimum production parameters: catalyst amount, alcohol amount, temperature, agitation speed and reaction time were determined experimentally and found to be: 1.0 wt% catalyst amount, 30 wt% methanol amount, 60 C reaction temperature, 400 rpm agitation rate and 60 min reaction time. With these optimal conditions the conversion efficiency was 82%. The properties of the moringa biodiesel that was produced were observed to fall within the recommended international biodiesel standards. However, moringa biodiesel showed high values of cloud and pour points of 10 C and 3 C respectively, which present a problem as regards use in cold temperatures. (author)

Matrix isolation FT-IR spectroscopy and molecular orbital study of sarcosine methyl ester

OpenAIRE

Gómez-Zavaglia, Andrea; Fausto, R.

2004-01-01

N-methylglycine methyl ester (sarcosine-Me) has been studied by matrix isolation FT-IR spectroscopy and molecular orbital calculations undertaken at the DFT/B3LYP and MP2 levels of theory with the 6-311++G(d,p) and 6-31++G(d,p) basis set, respectively. Twelve different conformers were located in the potential energy surface of the studied compound, with the ASC conformer being the ground conformational state. This form is analogous to the dimethylglycine methyl ester most stable conformer and...

Comparative life cycle assessment of biodiesel and fossil diesel fuel

International Nuclear Information System (INIS)

Ceuterick, D.; Nocker, L. De; Spirinckx, C.

1999-01-01

Biofuels offer clear advantages in terms of greenhouse gas emissions, but do they perform better when we look at all the environmental impacts from a life cycle perspective. In the context of a demonstration project at the Flemish Institute for Technology Research (VITO) on the use of rapeseed methyl ester (RME) or biodiesel as automotive fuel, a life cycle assessment (LCA) of biodiesel and diesel was made. The primary concern was the question as to whether or not the biodiesel chain was comparable to the conventional diesel chain, from an environmental point of view, taking into account all stages of the life cycle of the two products. Additionally, environmental damage costs were calculated, using an impact pathway analysis. This paper presents the results of the two methods for evaluation of environmental impacts of RME and conventional diesel. Both methods are complementary and share the conclusion that although biodiesel has much lower greenhouse gas emissions, it still has significant impacts on other impact categories. The external costs of biodiesel are a bit lower compared to fossil diesel. For both fuels, external costs are significantly higher than the private production cost. (Author)

A Simple and Fast Method for the Production and Characterization of Methylic and Ethylic Biodiesels from Tucum Oil via an Alkaline Route

Directory of Open Access Journals (Sweden)

Marcelo Firmino de Oliveira

2011-01-01

Full Text Available A simple, fast, and complete route for the production of methylic and ethylic biodiesel from tucum oil is described. Aliquots of the oil obtained directly from pressed tucum (pulp and almonds were treated with potassium methoxide or ethoxide at 40°C for 40 min. The biodiesel form was removed from the reactor and washed with 0.1 M HCl aqueous solution. A simple distillation at 100°C was carried out in order to remove water and alcohol species from the biodiesel. The oxidative stability index was obtained for the tucum oil as well as the methylic and ethylic biodiesel at 6.13, 2.90, and 2.80 h, for storage times higher than 8 days. Quality control of the original oil and of the methylic and ethylic biodiesels, such as the amount of glycerin produced during the transesterification process, was accomplished by the TLC, GC-MS, and FT-IR techniques. The results obtained in this study indicate a potential biofuel production by simple treatment of tucum, an important Amazonian fruit.

Microwave-assisted pyrolysis of methyl ricinoleate for continuous production of undecylenic acid methyl ester (UAME).

Science.gov (United States)

Nie, Yong; Duan, Ying; Gong, Ruchao; Yu, Shangzhi; Lu, Meizhen; Yu, Fengwen; Ji, Jianbing

2015-06-01

Undecylenic acid methyl ester (UAME) was continuously produced from methyl ricinoleate using a microwave-assisted pyrolysis system with atomization feeding. The UAME yield of 77 wt.% was obtained at 500°C using SiC as the microwave absorbent and heating medium. The methyl ricinoleate conversion and UAME yield from microwave-assisted pyrolysis process were higher than those from conventional pyrolysis. The effect of temperature on the pyrolysis process was also investigated. The methyl ricinoleate conversion increased but the cracking liquid yield decreased when the temperature increased from 460°C to 560°C. The maximum UAME yield was obtained at the temperature of 500°C. Copyright © 2015 Elsevier Ltd. All rights reserved.

Mechanistic study on spraying of blended biodiesel using phase Doppler anemometry

International Nuclear Information System (INIS)

Kamrak, Juthamas; Kongsombut, Benjapol; Grehan, Gerard; Saengkaew, Sawitree; Kim, Kyo-Seon; Charinpanitkul, Tawatchai

2009-01-01

Droplet size and dynamics of blended palm oil-based fatty acid methyl ester (FAME) and diesel oil spray were mechanistically investigated using a phase Doppler anemometry. A two-fluid atomizer was applied for dispersing viscous blends of blended biodiesel oil with designated flow rates. It was experimentally found that the atomizer could generate a spray with large droplets with Sauter mean diameters of ca. 30 μm at low air injection pressure. Such large droplets traveled with a low velocity along their trajectory after emerging from the nozzle tip. The viscosity of blended biodiesel could significantly affect the atomizing process, resulting in the controlled droplet size distribution. Blended biodiesel with a certain fraction of palm oil-based FAME would be consistently atomized owing to its low viscosity. However, the viscosity could exert only a small effect on the droplet velocity profile with the air injection pressure higher than 0.2 MPa.

Biodiesel's Characteristics Preparation from Palm Oil

Directory of Open Access Journals (Sweden)

Tilani Hamid

2010-10-01

Full Text Available Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio = 5 : 1, amount of NaOH used as catalyst = 3.5 gr, 4.5 gr, 5 gr and 5.5 gr and it takes about one hour time reaction. The ester (metil ester produced are separated from glycerin and washed until it takes normal pH (6-7 where more amount of catalyst used will decrease the ester (biodiesel produced. The results show that biodiesels' properties made by using 3.5 (M3.5 gr, 4.5 gr (M4.5 and 5 (M5.0 gr catalyst close to industrial diesel oil and the other (M5.5 closes to automotive diesel oil, while blending diesel oil with 20 % biodiesel (B20 is able to improve the diesel engine performances.

Process Optimization for Biodiesel Production from Corn Oil and Its Oxidative Stability

Directory of Open Access Journals (Sweden)

N. El Boulifi

2010-01-01

Full Text Available Response surface methodology (RSM based on central composite design (CCD was used to optimize biodiesel production process from corn oil. The process variables, temperature and catalyst concentration were found to have significant influence on biodiesel yield. The optimum combination derived via RSM for high corn oil methyl ester yield (99.48% was found to be 1.18% wt catalyst concentration at a reaction temperature of 55.6∘C. To determine how long biodiesel can safely be stored, it is desirable to have a measurement for the stability of the biodiesel against such oxidation. Storage time and oxygen availability have been considered as possible factors influencing oxidative instability. Biodiesel from corn oil was stored for a period of 30 months, and the physico-chemical parameters of samples were measured at regular interval of time. Results show that the acid value (AV, peroxide value (PV, and viscosity (ν increased while the iodine value (IV decreased. These parameters changed very significantly when the sample was stored under normal oxygen atmosphere. However, the ν, AV, and IV of the biodiesel sample which was stored under argon atmosphere were within the limit by the European specifications (EN 14214.

Aprovechamiento de las oleinas residuales procedentes del proceso de refinado de los aceites vegetales comestibles, para la fabricación de biodiesel

OpenAIRE

Álvarez Mateos, P.; Barriga Mateos, F.; Pereda Marín, J.

2003-01-01

A procedure to obtain Biodiesel from “Oleinas” is studied. Biodiesel is a suitable product to replace diesel oil currently used to power the Diesel engines. It consists of a mixture of methyl esters of the fatty acids presents as triglycerides in vegetables oils (olive, sunflower, soya, rape oils). As a result of the refining of these oils for their use as food, a waste product is formed, the “oleinas” (acidulated soapstock)....

Biodiesel production from residual oils recovered from spent bleaching earth

International Nuclear Information System (INIS)

Huang, Yi-Pin; Chang, James I.

2010-01-01

This work was to study technical and economic feasibilities of converting residual oils recovered from spent bleaching earth generated at soybean oil refineries into useable biodiesel. Experimental results showed that fatty acids in the SBE residual oil were hexadecenoic acid (58.19%), stearic acid (21.49%) and oleic acid (20.32%), which were similar to those of vegetable oils. The methyl ester conversion via a transesterification process gave a yield between 85 and 90%. The biodiesel qualities were in reasonable agreement with both EN 14214 and ASTM D6751 standards. A preliminary financial analysis showed that the production cost of biodiesel from SBE oils was significantly lower than the pre-tax price of fossil diesel or those made of vegetable oils or waste cooking oils. The effects of the crude oil price and the investment on the production cost and the investment return period were also conducted. The result showed that the investment would return faster at higher crude oil price. (author)

Combustion of jojoba methyl ester in an indirect injection diesel engine

Energy Technology Data Exchange (ETDEWEB)

Selim, M.Y.E. [United Arab Emirates University, Al-Ain (United Arab Emirates). Mechanical Engineering Dept.; Radwan, M.S.; Elfeky, S.M.S. [Helwan University, Cairo (Egypt). Mechanical Power Engineering Dept.

2003-07-01

An experimental investigation has been carried out to examine for the first time the performance and combustion noise of an indirect injection diesel engine running with new fuel derived from pure jojoba oil, jojoba methyl ester, and its blends with gas oil. A Ricardo E6 compression swirl diesel engine was fully instrumented for the measurement of combustion pressure and its rise rate and other operating parameters. Test parameters included the percentage of jojoba methyl ester in the blend, engine speed, load, injection timing and engine compression ratio. Results showed that the new fuel derived from jojoba is generally comparable and a good replacement to gas oil in diesel engine at most engine operating conditions, in terms of performance parameters and combustion noise produced. (author)

Indigenous oil crops as a source for production of biodiesel in Kenya

Directory of Open Access Journals (Sweden)

R.L.A. Mahunnah

2009-12-01

Full Text Available In this study, oils extracted from four crops, Jatropha curcas L., Croton megalocarpus Hutch, Calodendrum capense (L.f. Thunb. (cape chestnut and Cocos nucifera L. (coconut were transesterified in methanol using sodium hydroxide as a catalyst. Methyl esters obtained were characterized by GC-MS and further tested for fuel properties relative to convectional diesel fuels (automotive and kerosene. Methyl esters of commercial oils: sunflower and soybean were also tested for fuel properties for comparison. Some of parameters tested included kinematic viscosity, flash point, distillation temperatures, copper corrosion, cetane number, ash content, and gross heating value. The results showed hexadecanoate and octadecanoate were common fatty acids esters identified in the four analyzed methyl esters. Total unsaturation was highest for Croton ester with 86.6 %, Jatropha and C. capense esters had unsaturation of 65.2 % and 61.2 %, respectively, while coconut ester recorded only 2.8 %. The ester viscosities at 40 °C were with range of 4.16-4.63 mm2/s except coconut ester with viscosity 2.71 mm2/s, which is close to that of kerosene 2.35 mm2/s. The esters were found to be less volatile that diesel fuels with coconut esters registering as most volatile among the esters. Esters of sunflower and soybean have their volatility very close to that of Jatropha ester. The flash points of the esters were typically much higher (> 100 °C than petroleum diesels, automotives and kerosene (74 and 45.5 °C, respectively. Jatropha, sunflower and soybean esters passed the ASTM standard D6751 for flash point; 130 °C minimum, all the esters however were within the European standard EN-14214 for biodiesel of above 101 °C. The density of the esters was found to be 2-4 % higher than that of petroleum automotive diesel and 10-12 % more than that of kerosene. The heating values of the esters were however 12 % lower than diesel fuels on average. In general, coconut esters were

Fuel spray combustion of waste cooking oil and palm oil biodiesel: Direct photography and detailed chemical kinetics

KAUST Repository

Kuti, Olawole

2013-10-14

This paper studies the ignition processes of two biodiesel from two different feedstock sources, namely waste cooked oil (WCO) and palm oil (PO). They were investigated using the direct photography through high-speed video observations and detailed chemical kinetics. The detailed chemical kinetics modeling was carried out to complement data acquired using the high-speed video observations. For the high-speed video observations, an image intensifier combined with OH* filter connected to a high-speed video camera was used to obtain OH* chemiluminscence image near 313 nm. The OH* images were used to obtain the experimental ignition delay of the biodiesel fuels. For the high-speed video observations, experiments were done at an injection pressure of 100, 200 and 300 MPa using a 0.16 mm injector nozzle. Also a detailed chemical kinetics for the biodiesel fuels was carried out using ac chemical kinetics solver adopting a 0-D reactor model to obtain the chemical ignition delay of the combusting fuels. Equivalence ratios obtained from the experimental ignition delay were used for the detailed chemical kinetics analyses. The Politecnico di Milano\\'s thermochemical and reaction kinetic data were adopted to simulate the ignition processes of the biodiesels using the five fatty acid methyl esters (FAME) major components in the biodiesel fuels. From the high-speed video observations, it was observed that at increasing injection pressure, experimental ignition delay increased as a result of improvement in fuel and air mixing effects. Also the palm oil biodiesel has a shorter ignition delay compared to waste cooked oil biodiesel. This phenomenon could be attributed to the higher cetane number of palm biodiesel. The fuel spray ignition properties depend on both the physical ignition delay and chemical ignition delay. From the detailed chemical kinetic results it was observed that at the low temperature, high ambient pressure conditions reactivity increased as equivalent ratio

Fuel spray combustion of waste cooking oil and palm oil biodiesel: Direct photography and detailed chemical kinetics

KAUST Repository

Kuti, Olawole; Nishida, Keiya; Sarathy, Mani; Zhu, Jingyu

2013-01-01

This paper studies the ignition processes of two biodiesel from two different feedstock sources, namely waste cooked oil (WCO) and palm oil (PO). They were investigated using the direct photography through high-speed video observations and detailed chemical kinetics. The detailed chemical kinetics modeling was carried out to complement data acquired using the high-speed video observations. For the high-speed video observations, an image intensifier combined with OH* filter connected to a high-speed video camera was used to obtain OH* chemiluminscence image near 313 nm. The OH* images were used to obtain the experimental ignition delay of the biodiesel fuels. For the high-speed video observations, experiments were done at an injection pressure of 100, 200 and 300 MPa using a 0.16 mm injector nozzle. Also a detailed chemical kinetics for the biodiesel fuels was carried out using ac chemical kinetics solver adopting a 0-D reactor model to obtain the chemical ignition delay of the combusting fuels. Equivalence ratios obtained from the experimental ignition delay were used for the detailed chemical kinetics analyses. The Politecnico di Milano's thermochemical and reaction kinetic data were adopted to simulate the ignition processes of the biodiesels using the five fatty acid methyl esters (FAME) major components in the biodiesel fuels. From the high-speed video observations, it was observed that at increasing injection pressure, experimental ignition delay increased as a result of improvement in fuel and air mixing effects. Also the palm oil biodiesel has a shorter ignition delay compared to waste cooked oil biodiesel. This phenomenon could be attributed to the higher cetane number of palm biodiesel. The fuel spray ignition properties depend on both the physical ignition delay and chemical ignition delay. From the detailed chemical kinetic results it was observed that at the low temperature, high ambient pressure conditions reactivity increased as equivalent ratio

Heterogeneous catalyzed biodiesel production from Moringa oleifera oil

Energy Technology Data Exchange (ETDEWEB)

Kafuku, Gerald; Mbarawa, Makame [Department of Mechanical Engineering, Tshwane University of Technology, Private Bag X680, Pretoria 001 (South Africa); Lam, Man Kee; Kansedo, Jibrail; Lee, Keat Teong [School of Chemical Engineering, Universiti Sains Malaysia, Engineering Campus, Seri Ampangan, 14300 Nibong Tebal, Pulau Pinang (Malaysia)

2010-11-15

In this study, biodiesel was produced from Moringa oleifera oil using sulfated tin oxide enhanced with SiO{sub 2} (SO{sub 4}{sup 2-}/SnO{sub 2}-SiO{sub 2}) as super acid solid catalyst. The experimental design was done using design of experiment (DoE), specifically, response surface methodology based on three-variable central composite design (CCD) with alpha ({alpha}) = 2. The reaction parameters studied were reaction temperature (60 C to 180 C), reaction period (1 h to 3 h) and methanol to oil ratio (1:6 to 1:24). It was observed that the yield up to 84 wt.% of Moringa oleifera methyl esters can be obtained with reaction conditions of 150 C temperature, 150 min reaction time and 1:19.5 methanol to oil ratio, while catalyst concentration and agitation speed are kept at 3 wt.% and 350-360 rpm respectively. Therefore this study presents the possibility of converting a relatively new oil feedstock, Moringa oleifera oil to biodiesel and thus reducing the world's dependency on existing edible oil as biodiesel feedstock. (author)

Optimization and characterization of biodiesel production from microalgae Botryococcus grown at semi-continuous system

International Nuclear Information System (INIS)

Ashokkumar, Veeramuthu; Agila, Elango; Sivakumar, Pandian; Salam, Zainal; Rengasamy, Ramasamy; Ani, Farid Nasir

2014-01-01

Highlights: • Bioprospecting for Botryococcus in upstream and downstream process for bioenergy production. • Large scale cultivation of B. braunii at semi-continuous system under open raceway system. • The biomass was harvested 99.5% successfully by Poly-(D)glucosamine and ferric iron. • Botryococcus biodiesel was characterized and found within ASTM standards. • Under semi-continuous mode, the alga B. braunii produces 101 tons ha −1 year −1 . - Abstract: The indigenous strain Botryococcus braunii TN101 was isolated and acclimatized under laboratory condition. Upstream and downstream process was thoroughly explored for biofuel production. During semi-continuous cultivation, the alga was grown under batch mode for 6 days; thereafter 40% of algal culture was harvested at every three days interval. At semi-continuous system, the indigenous strain grows well and produces high biomass productivity of 33.8 g m −3 day −1 . A two step combined harvesting process was designed using ferric iron and organic polymer Poly-(D)glucosamine and harvested 99.5% of biomass. Lipid extraction was optimized using different solvents, cyclohexane and methanol at 3:1 ratio supported for maximum extraction of lipids in Botryococcus up to 26.3%. Physicochemical properties of lipid was analyzed and found, saponification values 184, ester values 164, iodine values 92 and the average molecular weight of the lipids are 920 g mol −1 . The lipid contains 9.7% of FFA level, therefore, a simultaneous esterification and transesterification of free fatty acids and triacylglycerides were optimized for biodiesel production and the methyl ester yield was recorded up to 84%. In addition, an optimization study was carried out for the removal of pigments present in the biodiesel; the result revealed that 99% of pigments were removed from the biodiesel using activated charcoal. The biodiesel profile was analyzed by 1 H and 13 C NMR and GC–MS analyzer, methyl palmitate and methyl oleate

Effect of nature based antioxidant from Zingiber officinale Rosc. on the oxidation stability, engine performance and emission characteristics with neem oil methyl ester

Science.gov (United States)

Karthickeyan, V.

2018-05-01

In past few years, the demand for energy increased drastically due to excess utilization of the natural reserves. Thus, it leads to extinction of non-renewable energy resources. Today, the world turning over renewable source of energy for power production (like wind energy, tidal energy, biodiesel, biomass and so on). In the present study, raw neem oil was taken and converted into biodiesel using transesterification process. Nature based antioxidant namely ginger extract (Zingiber officinale Rosc.) was used as an antioxidant instead of synthetic antioxidants. An anti-oxidants were added in various proportions like G5 (0.5% additive), G10 (1% additive) and G15 (1.5% additive) with B20 (20% neem oil methyl ester with 80% diesel). B20G15 sample showed higher induction period than other samples. Thus, it was considered as an optimum blend with oxidation stability test using Rancimat instrument. Diesel showed higher Brake Thermal Efficiency (BTE) than biodiesel samples. On the other hand, B20G15 showed higher BTE than B20. Higher CO, HC and smoke emissions were observed for B20 with an antioxidant than other fuel samples. B20 with an antioxidant showed lower NOx emissions than diesel and B20. Thus, the nature based antioxidant was considered as the most promising alternative for NOx emission reduction.

Optimization of Alkali Catalyzed Transesterification of Safflower Oil for Production of Biodiesel

Directory of Open Access Journals (Sweden)

M. C. Math

2016-01-01

Full Text Available The Central Composite Design is used for the optimization of alkaline catalyzed transesterification parameters such as methanol quantity, catalytic concentration, and rotational speed by keeping the temperature and reaction time constant. The Central Composite Design method is employed to get the maximum safflower oil methyl ester yield. The combined effects of catalyst concentration, rotational speed, and molar ratio of alcohol to oil were investigated and optimized using response surface methodology. A statistical model has predicted the maximum yield of safflower oil methyl ester (94.69% volume of oil parameters such as catalyst concentration (0.6 grams, methanol amount (30 mL, rotational speed (600 rpm, and keeping constant reaction temperature (55°C to 65°C and reaction time (60 minutes. Experimental maximum yield of 91.66% was obtained at above parameters. XLSTAT is used to generate a linear model to predict the methyl ester yield as a function of methanol quantity, catalyst concentration, and rotational speed by keeping constant reaction temperature (55°C to 65°C and reaction time (60 minutes. MINITAB is used to draw the 3D response surface plot and 2D contour plot to predict the maximum biodiesel yield.

Waste cockle shell as natural catalyst for biodiesel production from jatropha oil

Science.gov (United States)

Hadi, Norulakmal Nor; Idrus, Nur Afini; Ghafar, Faridah; Salleh, Marmy Roshaidah Mohd

2017-12-01

Due to the increasing of industrialization and modernization of the world, the demand of petroleum has risen rapidly. The increasing demand for energy and environmental awareness has prompted many researches to embark on alternative fuel platforms that are environmentally acceptable. In this study, jatropha oil was used to produce biodiesel by a new transesterification routine in which cockle shell was used as source of heterogeneous catalyst. The investigation showed the catalyst that was calcined at temperature of 800 °C has the optimum capability to produce high yield. The highest yield of biodiesel production of 93.20 % were obtained by using 1.5 wt% of catalyst. The reaction was conducted at a temperature of 65 °C with the optimum methanol to oil ratio of 6:1. It was found that the physical properties of the biodiesel produced were significant to ASTM standard of fatty acid methyl ester (FAME).

Synthesis of fatty acid methyl ester from palm oil (Elaeis guineensis) with Ky(MgCa)2xO3 as heterogeneous catalyst.

Science.gov (United States)

Olutoye, M A; Lee, S C; Hameed, B H

2011-12-01

Fatty acid methyl esters (FAME) were produced from palm oil using eggshell modified with magnesium and potassium nitrates to form a composite, low-cost heterogeneous catalyst for transesterification. The catalyst, prepared by the combination of impregnation/co-precipitation was calcined at 830 °C for 4 h. Transesterification was conducted at a constant temperature of 65 °C in a batch reactor. Design of experiment (DOE) was used to optimize the reaction parameters, and the conditions that gave highest yield of FAME (85.8%) was 5.35 wt.% catalyst loading at 4.5 h with 16:1 methanol/oil molar ratio. The results revealed that eggshell, a solid waste, can be utilized as low-cost catalyst after modification with magnesium and potassium nitrates for biodiesel production. Copyright © 2011 Elsevier Ltd. All rights reserved.

Potential plant oil feedstock for lipase-catalyzed biodiesel production in Thailand

Energy Technology Data Exchange (ETDEWEB)

Winayanuwattikun, Pakorn; Kaewpiboon, Chutima; Piriyakananon, Kingkaew; Tantong, Supalak; Thakernkarnkit, Weerasak; Yongvanich, Tikamporn [Department of Biochemistry, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand); Biofuel Production by Biocatalyst Research Unit, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand); Chulalaksananukul, Warawut [Department of Botany, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand); Biofuel Production by Biocatalyst Research Unit, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand)

2008-12-15

Twenty-seven types of plants found to contain more than 25% of oil (w/w) were selectively examined from 44 species. Saponification number (SN), iodine value (IV), cetane number (CN) and viscosity ({eta}) of fatty acid methyl esters (FAMEs) of oils were empirically determined, and they varied from 182 to 262, 3.60 to 142.70, 39.32 to 65.80 and 2.29 to 3.95, respectively. Fatty acid compositions, IV, CN and {eta} were used to predict the quality of FAMEs for use as biodiesel. FAMEs of plant oils of 15 species were found to be most suitable for use as biodiesel by meeting the major specification of biodiesel standards of Thailand, USA and European Standard Organization. The oils from these 15 species were further investigated for the conversion efficiency of biodiesel in lipase-catalyzed transesterification reaction with Novozyme 435 and Lipozyme RM IM. Oils of four species, palm (Elaeis guineensis), physic nut (Jatropha curcas), papaya (Carica papaya) and rambutan (Nephelium lappaceum), can be highly converted to biodiesel by transesterification using Novozyme 435- or Lipozyme RM IM-immobilized lipase as catalyst. Therefore, these selected plants would be economically considered as the feedstock for biodiesel production by biocatalyst. (author)

Upon the opportunity to apply ART2 Neural Network for clusterization of biodiesel fuels

Directory of Open Access Journals (Sweden)

Petkov T.

2016-03-01

Full Text Available A chemometric approach using artificial neural network for clusterization of biodiesels was developed. It is based on artificial ART2 neural network. Gas chromatography (GC and Gas Chromatography - mass spectrometry (GC-MS were used for quantitative and qualitative analysis of biodiesels, produced from different feedstocks, and FAME (fatty acid methyl esters profiles were determined. Totally 96 analytical results for 7 different classes of biofuel plants: sunflower, rapeseed, corn, soybean, palm, peanut, “unknown” were used as objects. The analysis of biodiesels showed the content of five major FAME (C16:0, C18:0, C18:1, C18:2, C18:3 and those components were used like inputs in the model. After training with 6 samples, for which the origin was known, ANN was verified and tested with ninety “unknown” samples. The present research demonstrated the successful application of neural network for recognition of biodiesels according to their feedstock which give information upon their properties and handling.

Upon the opportunity to apply ART2 Neural Network for clusterization of biodiesel fuels

Science.gov (United States)

Petkov, T.; Mustafa, Z.; Sotirov, S.; Milina, R.; Moskovkina, M.

2016-03-01

A chemometric approach using artificial neural network for clusterization of biodiesels was developed. It is based on artificial ART2 neural network. Gas chromatography (GC) and Gas Chromatography - mass spectrometry (GC-MS) were used for quantitative and qualitative analysis of biodiesels, produced from different feedstocks, and FAME (fatty acid methyl esters) profiles were determined. Totally 96 analytical results for 7 different classes of biofuel plants: sunflower, rapeseed, corn, soybean, palm, peanut, "unknown" were used as objects. The analysis of biodiesels showed the content of five major FAME (C16:0, C18:0, C18:1, C18:2, C18:3) and those components were used like inputs in the model. After training with 6 samples, for which the origin was known, ANN was verified and tested with ninety "unknown" samples. The present research demonstrated the successful application of neural network for recognition of biodiesels according to their feedstock which give information upon their properties and handling.

Adsorption and wettability study of methyl ester sulphonate on precipitated asphaltene

International Nuclear Information System (INIS)

Okafor, H E; Gholami, R; Sukirman, Y

2016-01-01

Asphaltene precipitation from crude oil and its subsequent aggregation forms solid, which preferentially deposit on rock surfaces causing formation damage and wettability changes leading to loss of crude oil production. To resolve this problem, asphaltene inhibitor has been injected into the formation to prevent the precipitation of asphaltene. Asphaltene inhibitors that are usually employed are generally toxic and non-biodegradable. This paper presents a new environmentally friendly asphaltene inhibitor (methyl ester sulphonate), an anionic surfactant, which has excellent sorption on formation rock surfaces. Result from adsorption study validated by Langmuir and Freundlich models indicate a favourable adsorption. At low volumes injected, methyl ester sulphonate is capable of reverting oil-wet sandstone surface to water-wet surface. Biodegradability test profile shows that for concentrations of 100-5000ppm it is biodegradable by 65-80%. (paper)

Mechanistic study on spraying of blended biodiesel using phase Doppler anemometry

Energy Technology Data Exchange (ETDEWEB)

Kamrak, Juthamas; Kongsombut, Benjapol; Charinpanitkul, Tawatchai [Center of Excellence in Particle Technology, Department of Chemical Engineering, Faculty of Engineering, Chulalongkorn University, Payathai Road, Patumwan, Bangkok 10330 (Thailand); Grehan, Gerard; Saengkaew, Sawitree [LESP/UMR CNRS6614/INSA et Universite de Rouen, BP 12, avenue de l' universite, 76801, Saint Etienne du Rouvray (France); Kim, Kyo-Seon [Department of Chemical Engineering, Faculty of Engineering, Kangwon National University, Chuncheon (Korea)

2009-10-15

Droplet size and dynamics of blended palm oil-based fatty acid methyl ester (FAME) and diesel oil spray were mechanistically investigated using a phase Doppler anemometry. A two-fluid atomizer was applied for dispersing viscous blends of blended biodiesel oil with designated flow rates. It was experimentally found that the atomizer could generate a spray with large droplets with Sauter mean diameters of ca. 30 {mu}m at low air injection pressure. Such large droplets traveled with a low velocity along their trajectory after emerging from the nozzle tip. The viscosity of blended biodiesel could significantly affect the atomizing process, resulting in the controlled droplet size distribution. Blended biodiesel with a certain fraction of palm oil-based FAME would be consistently atomized owing to its low viscosity. However, the viscosity could exert only a small effect on the droplet velocity profile with the air injection pressure higher than 0.2 MPa. (author)

Two-step microalgal biodiesel production using acidic catalyst generated from pyrolysis-derived bio-char

International Nuclear Information System (INIS)

Dong, Tao; Gao, Difeng; Miao, Chao; Yu, Xiaochen; Degan, Charles; Garcia-Pérez, Manuel; Rasco, Barbara; Sablani, Shyam S.; Chen, Shulin

2015-01-01

Highlights: • Highly active catalyst was prepared using bio-char co-produced in Auger pyrolysis. • Catalyst inhibitors in crude oil were effectively removed by a practical refinery process. • Free fatty acids (FFA) content in refined microalgal oil was reduced to less than 0.5%. • A total fatty acid methyl ester (FAME) yield of 99% was obtained via a two-step process. • The inexpensive bio-char catalyst is superior to Amberlyst-15 in pre-esterification. - Abstract: An efficient process for biodiesel production from fast-refined microalgal oil was demonstrated. A low cost catalyst prepared from pyrolysis-derived bio-char, was applied in pre-esterification to reduce free fatty acid (FFA) content. Results showed that the bio-char catalyst was highly active in esterification; however, the performance of the catalyst significantly reduced when crude microalgal oil was used as feedstock. To solve the problem caused by catalyst-fouling, a fast and scalable crude oil refinery procedure was carried out to remove chlorophyll and phospholipids that might degrade the catalyst and the quality of biodiesel. The activity and reusability of bio-char catalyst were remarkably improved in the fast-refined oil. FFA content in the refined microalgal oil was reduced to less than 0.5% after pre-esterification. The bio-char catalyst could be reused for 10 cycles without dramatic loss in activity. The pre-esterification fits the first-order kinetic reaction with activation energy of 42.16 kJ/mol. The activity of bio-char catalyst was superior to commercial Amberlyst-15 under the same reaction condition. A total fatty acid methyl ester (FAME, namely biodiesel) yield of 99% was obtained following the second-step CaO-catalyzed transesterification. The cost-effective bio-char catalyst has great potential for biodiesel production using feedstocks having high FFA content.

Ultrasonic assisted biodiesel production of microalgae by direct transesterification

Science.gov (United States)

Kalsum, Ummu; Mahfud, Mahfud; Roesyadi, Achmad

2017-03-01

Microalgae are considered as the third generation source of biofuel and an excellent candidate for biofuel production to replace the fossil energy. The use of ultrasonic in producing biodiesel by direct transesterification of Nannochloropsis occulata using KOH as catalyst and methanol as a solvent was investigated. The following condition were determined as an optimum by experimental evaluates:: 1: 15 microalga to methanol (molar ratio); 3% catalyst concentration at temperature 40°C after 30 minute of ultrasonication. The highest yield of biodiesel produced was 30.3%. The main components of methyl ester from Nannochloropsis occulata were palmitic (C16 :0),, oleic (C18:1), stearic (C18;0), arahidic (C20:0) and myristic (C14:0). This stated that the application of ultrasounic for direct transesterificaiton of microalgae effectively reduced the reaction time compared to the reported values of conventional heating systems.

Determination model for cetane number of biodiesel at different fatty acid composition: a review

Directory of Open Access Journals (Sweden)

Michal Angelovič

2014-05-01

Full Text Available The most accepted definition of biodiesel is stated at the EU technical regulation EN 14214 (2008 or in the USA in ASTM 6751-02. As a result of this highly strict description only methyl esters of fatty acids conform to these definitions, nevertheless the term ‘‘biodiesel’’ is spread out to other alkyl fatty esters. Some countries have adopted bioethanol for replacement of methanol in biodiesel transesterification and thus assuring a fully biological fuel. Of course, such position brings some problems in fulfilling technical requirements of EN 14214 or ASTM 6751-02. Biodiesel is actually a less complex mixture than petrodiesel, but different feedstock origins and the effect of seasonality may impose difficulties in fuel quality control. Since biodiesel is an alternative diesel fuel derived from the transesterification of triacylglycerol comprised materials, such as vegetable oils or animal fats, with simple alcohols to furnish the corresponding mono-alkyl esters, its composition depends on the raw material used, the cultivated area location, and harvest time. The choice of the raw material is usually the most important factor for fluctuations of biodiesel composition, because different vegetable oils and animal fats may contain different types of fatty acids. Important properties of this fuel vary significantly with the composition of the mixture. Cetane number, melting point, degree of saturation, density, cloud point, pour point, viscosity, and nitrogen oxides exhaust emission (NOx, for instance, deserve to be mentioned. One of the most important fuel quality indicators is the cetane number; however its experimental determination may be an expensive and lengthy task. To weaken situation concerning biodiesel, the availability of data in the literature is also scarce. In such scenario, the use of reliable models to predict the cetane number or any other essential characteristic may be of great utility. We reviewed available literature to

Biodiesel from waste cooking oil via base-catalytic and supercritical methanol transesterification

International Nuclear Information System (INIS)

Demirbas, Ayhan

2009-01-01

In this study, waste cooking oil has subjected to transesterification reaction by potassium hydroxide (KOH) catalytic and supercritical methanol methods obtaining for biodiesel. In catalyzed methods, the presence of water has negative effects on the yields of methyl esters. In the catalytic transesterification free fatty acids and water always produce negative effects since the presence of free fatty acids and water causes soap formation, consumes catalyst, and reduces catalyst effectiveness. Free fatty acids in the waste cooking oil are transesterified simultaneously in supercritical methanol method. Since waste cooking oil contains water and free fatty acids, supercritical transesterification offers great advantage to eliminate the pre-treatment and operating costs. The effects of methanol/waste cooking oils ratio, potassium hydroxide concentration and temperature on the biodiesel conversion were investigated

Biodiesel Production from Selected Microalgae Strains and Determination of its Properties and Combustion Specific Characteristics

Directory of Open Access Journals (Sweden)

N. Kokkinos

2015-11-01

Full Text Available Biofuels are gaining importance as significant substitutes for the depleting fossil fuels. Recent focus is on microalgae as the third generation feedstock. In the present research work, two indigenous fresh water and two marine Chlorophyte strains have been cultivated successfully under laboratory conditions using commercial fertilizer (Nutrileaf 30-10-10, initial concentration=70 g/m3 as nutrient source. Gas chromatographic analysis data showed that microalgae biodiesel obtained from Chlorophyte strains biomass were composed of fatty acid methyl esters. The produced microalgae biodiesel achieved a range of 2.2 - 10.6 % total lipid content and an unsaturated FAME content between 49 mol% and 59 mol%. The iodine value, the cetane number, the cold filter plugging point, the oxidative stability as well as combustion specific characteristics of the final biodiesels were determined based on the compositions of the four microalgae strains. The calculated biodiesel properties compared then with the corresponding properties of biodiesel from known vegetable oils, from other algae strains and with the specifications in the EU (EN 14214 and US (ASTM D6751 standards. The derived biodiesels from indigenous Chlorophyte algae were significantly comparable in quality with other biodiesels.

The occurrence of 2-hydroxy-6-methoxybenzoic acid methyl ester in Securidaca longepedunculata Fresen root bark

Directory of Open Access Journals (Sweden)

Lognay G.

2000-01-01

Full Text Available As part of our ongoing search for natural fumigants from Senegalese plants, we have investigated Securicicidaca longepedunculata root barks and demonstrated that 2-hydroxy-benzoic acid methyl ester (methyl salicylate, I is responsible of their biocide effect against stored grain insects. A second unknown apparented product, II has been systematically observed in all analyzed samples. The present paper describes the identification of this molecule. The analytical investigations including GCMS, GLC and 1H-NMR. spectrometry led to the conclusion that II corresponds to the 2-hydroxy-6-methoxybenzoic acid methyl ester.

Retrofit of distillation columns in biodiesel production plants

International Nuclear Information System (INIS)

Nguyen, Nghi; Demirel, Yasar

2010-01-01

Column grand composite curves and the exergy loss profiles produced by the Column-Targeting Tool of the Aspen Plus simulator are used to assess the performance of the existing distillation columns, and reduce the costs of operation by appropriate retrofits in a biodiesel production plant. Effectiveness of the retrofits is assessed by means of thermodynamics and economic improvements. We have considered a biodiesel plant utilizing three distillation columns to purify biodiesel (fatty acid methyl ester) and byproduct glycerol as well as reduce the waste. The assessments of the base case simulation have indicated the need for modifications for the distillation columns. For column T202, the retrofits consisting of a feed preheating and reflux ratio modification have reduced the total exergy loss by 47%, while T301 and T302 columns exergy losses decreased by 61% and 52%, respectively. After the retrofits, the overall exergy loss for the three columns has decreased from 7491.86 kW to 3627.97 kW. The retrofits required a fixed capital cost of approximately $239,900 and saved approximately $1,900,000/year worth of electricity. The retrofits have reduced the consumption of energy considerably, and leaded to a more environmentally friendly operation for the biodiesel plant considered.

Economically viable production of biodiesel from a rural feedstock from eastern India, P. pinnata oil using a recyclable laboratory synthesized heterogeneous catalyst

International Nuclear Information System (INIS)

Singh, Veena; Hameed, Bassim H.; Sharma, Yogesh Chandra

2016-01-01

Graphical abstract: Barium zirconate was synthesized by co-precipitation method using nitrates of barium and zirconia and was applied for biodiesel production using karanja oil as feedstock through transesterification reaction. - Highlights: • Barium zirconate have been used as a heterogeneous catalyst for biodiesel production. • Effect of calcination time on stability of catalyst was studied. • 98.79 ± 0.5% of FAME conversion from karanja oil was attained. • Catalyst is stable and can be reused up to nine cycles with conversion up to >65%. • Glycerol obtained as a byproduct was easily purified for better use. - Abstract: Barium zirconate was synthesized by co-precipitation method and its feasibility as a heterogeneous catalyst for production of biodiesel (fatty acid methyl ester) was assessed. Fatty acid methyl ester (FAME) was synthesized through transesterification of karanja oil with methanol. Synthesized barium zirconate was characterized by Thermogravimetric analysis (TGA), Attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray diffractometry (XRD), Energy dispersive X-ray spectroscopy (EDS), and Scanning Electron Microscope (SEM). Specific surface area and basicity of the catalyst were also deliberated. Catalyst characterization indicated formation of single phase of barium zirconate which was capable of catalyzing the transesterification of esterified karanja oil with methanol. Feedstock was characterized by Gas Chromatography Mass Spectrometry (GC–MS). Reaction conditions such as molar ratio (oil:methanol), catalyst concentration, temperature, time, stirring speed and catalyst reusability were optimized. Calcination temperature and time significantly affected the catalytic activity of the catalyst because of variation in availability of basic sites. FAME conversion of 98.79 ± 0.5% was obtained at catalyst concentration of 1.0 wt%, 1:27 M ratio (oil:methanol), 65 °C for a 3 h contact time. The catalyst could be

Zeolite/magnetite composites as catalysts on the Synthesis of Methyl Esters (MES) from cooking oil

Science.gov (United States)

Sriatun; Darmawan, Adi; Sriyanti; Cahyani, Wuri; Widyandari, Hendri

2018-05-01

The using of zeolite/magnetite composite as a catalyst for the synthesis of methyl esters (MES) of cooking oil has been performed. In this study the natural magnetite was extracted from the iron sand of Semarang marina beach and milled by high energy Milling (HEM) with ball: magnetite ratio: 1:1. The composites prepared from natural zeolite and natural magnetite with zeolite: magnetite ratio 1:1; 2:1; 3:1 and 4:1. Preparation of methyl ester was catalyzed by composite of zeolite/magnetite through transeserification reaction, it was studied on variation of catalyst concentration (w/v) 1%, 3%, 5% and 10% to feed volume. The reaction product are mixture of methyl Oleic (MES), methyl Palmitic (MES) and methyl Stearic (MES). Character product of this research include density, viscosity, acid number and iodine number has fulfilled to SNI standard 7182: 2015.

4-[(2-Hydroxy-4-pentadecyl-benzylidene-amino]-benzoic Acid Methyl Ester

Directory of Open Access Journals (Sweden)

Gadada Naganagowda

2013-11-01

Full Text Available A new Schiff base, 4-[(2-hydroxy-4-pentadecyl-benzylidene-amino]-benzoic acid methyl ester was synthesized and its UV, IR, 1H-NMR, 13C-NMR and ESI-MS spectroscopic data are presented.

Biodiesel update

International Nuclear Information System (INIS)

Bee, K.

1998-01-01

Compared to gasoline driven spark ignition engines, diesel engines are more efficient and emit less CO 2 and CO. The use of mono-alkyl esters of long chain fatty acids derived from renewable lipid feed stocks such as vegetable oils or animal fats for use in compression ignition (diesel) engines was described. Production of this biodiesel product was illustrated. The raw materials for biodiesel include vegetable oil or animal fat, alcohol (methanol or ethanol), and a catalyst such as sodium hydroxide or potassium hydroxide. As far as uses are concerned, biodiesels can be used as a pure fuel, as a blending stock with petrodiesel, or in low levels with petrodiesel, indeed, anywhere where no. 1 or no. 2 petrodiesel is used. Details of the technical attributes of biodiesel were provided. The superior ability of biodiesel over petrodiesel to reduce particulates, carbon monoxide and unburned hydrocarbons was documented. A case study of using biodiesel fuel in an underground mine was part of the demonstration. 20 refs., 6 tabs