EQUITY SHARES EQUATING THE RESULTS OF FCFF AND FCFE METHODS

Directory of Open Access Journals (Sweden)

Bartłomiej Cegłowski

2012-06-01

Full Text Available The aim of the article is to present the method of establishing equity shares in weight average cost of capital (WACC, in which the value of loan capital results from the fixed assumptions accepted in the financial plan (for example a schedule of loan repayment and own equity is evaluated by means of a discount method. The described method causes that, regardless of whether cash flows are calculated as FCFF or FCFE, the result of the company valuation will be identical.

The new Inventory of Italian Glaciers: Present knowledge, applied methods and preliminary results

Science.gov (United States)

Smiraglia, Claudio; Diolaiuti, Guglielmina; D'Agata, Carlo; Maragno, Davide; Baroni, Carlo; Mortara, Gianni; Perotti, Luigi; Bondesan, Aldino; Salvatore, Cristina; Vagliasindi, Marco; Vuillermoz, Elisa

2013-04-01

A new Glacier Inventory is an indispensable requirement in Italy due to the importance of evaluating the present glacier coverage and the recent changes driven by climate. Furthermore Alpine glaciers represent a not negligible water and touristic resource then to manage and promote them is needed to know their distribution, size and features. The first Italian Glacier Inventory dates back to 1959-1962. It was compiled by the Italian Glaciological Committee (CGI) in cooperation with the National Research Council (CNR); this first inventory was mainly based on field data coupled with photographs (acquired on the field) and high resolution maps. The Italian glaciation resulted to be spread into 754 ice bodies which altogether were covering 525 km2. Moreover in the Eighties a new inventory was compiled to insert Italian data into the World Glacier Inventory (WGI); aerial photos taken at the end of the Seventies (and in some cases affected by a high and not negligible snow coverage) were used as the main source of data. No other national inventory were compiled after that period. Nevertheless during the last decade the largest part of the Italian Alpine regions have produced regional and local glacier inventories which in several cases are also available and queried through web sites and web GIS application. The actual need is now to obtain a complete, homogeneous and contemporary picture of the Italian Glaciation which encompasses the already available regional and local data and all the new updated information coming from new sources of data (e.g.: orthophotos, satellite imagines, etc..). The challenge was accepted by the University of Milan, the EvK2CNR Committee and the Italian Glaciological Committee who, with the sponsorship of Levissima Spa, are presently working to compile the new updated Italian Glacier Inventory. The first project step is to produce a unique homogeneous glacier database including glacier boundary and surface area and the main fundamental

Life cycle analysis of electricity systems: Methods and results

International Nuclear Information System (INIS)

Friedrich, R.; Marheineke, T.

1996-01-01

The two methods for full energy chain analysis, process analysis and input/output analysis, are discussed. A combination of these two methods provides the most accurate results. Such a hybrid analysis of the full energy chains of six different power plants is presented and discussed. The results of such analyses depend on time, site and technique of each process step and, therefore have no general validity. For renewable energy systems the emissions form the generation of a back-up system should be added. (author). 7 figs, 1 fig

Diagnosis of toxic alcohols: limitations of present methods.

Science.gov (United States)

Kraut, Jeffrey A

2015-01-01

Methanol, ethylene glycol, diethylene glycol, and propylene glycol intoxications are associated with cellular dysfunction and an increased risk of death. Adverse effects can develop quickly; thus, there is a need for methods for rapidly detecting their presence. To examine the value and limitations of present methods to diagnose patients with possible toxic alcohol exposure. I searched MEDLINE for articles published between 1969 and 2014 using the terms: toxic alcohols, serum osmolality, serum osmol gap, serum anion gap, metabolic acidosis, methanol, ethylene glycol, diethylene glycol, propylene glycol, and fomepizole. Each article was reviewed for additional references. The diagnosis of toxic alcohol exposure is often made on the basis of this history and physical findings along with an increase in the serum osmol and anion gaps. However, an increase in the osmol and/or anion gaps is not always present. Definitive detection in blood requires gas or liquid chromatography, laborious and expensive procedures which are not always available. Newer methods including a qualitative colorimetric test for detection of all alcohols or enzymatic tests for a specific alcohol might allow for more rapid diagnosis. Exposure to toxic alcohols is associated with cellular dysfunction and increased risk of death. Treatment, if initiated early, can markedly improve outcome, but present methods of diagnosis including changes in serum osmol and anion gap, and use of gas or liquid chromatography have important limitations. Development of more rapid and effective tests for detection of these intoxications is essential for optimal care of patients.

Methods for Presenting Braille Characters on a Mobile Device with a Touchscreen and Tactile Feedback.

Science.gov (United States)

Rantala, J; Raisamo, R; Lylykangas, J; Surakka, V; Raisamo, J; Salminen, K; Pakkanen, T; Hippula, A

2009-01-01

Three novel interaction methods were designed for reading six-dot Braille characters from the touchscreen of a mobile device. A prototype device with a piezoelectric actuator embedded under the touchscreen was used to create tactile feedback. The three interaction methods, scan, sweep, and rhythm, enabled users to read Braille characters one at a time either by exploring the characters dot by dot or by sensing a rhythmic pattern presented on the screen. The methods were tested with five blind Braille readers as a proof of concept. The results of the first experiment showed that all three methods can be used to convey information as the participants could accurately (91-97 percent) recognize individual characters. In the second experiment the presentation rate of the most efficient and preferred method, the rhythm, was varied. A mean recognition accuracy of 70 percent was found when the speed of presenting a single character was nearly doubled from the first experiment. The results showed that temporal tactile feedback and Braille coding can be used to transmit single-character information while further studies are still needed to evaluate the presentation of serial information, i.e., multiple Braille characters.

Using an analytical geometry method to improve tiltmeter data presentation

Science.gov (United States)

Su, W.-J.

2000-01-01

The tiltmeter is a useful tool for geologic and geotechnical applications. To obtain full benefit from the tiltmeter, easy and accurate data presentations should be used. Unfortunately, the most commonly used method for tilt data reduction now may yield inaccurate and low-resolution results. This article describes a simple, accurate, and high-resolution approach developed at the Illinois State Geological Survey for data reduction and presentation. The orientation of tiltplates is determined first by using a trigonometric relationship, followed by a matrix transformation, to obtain the true amount of rotation change of the tiltplate at any given time. The mathematical derivations used for the determination and transformation are then coded into an integrated PC application by adapting the capabilities of commercial spreadsheet, database, and graphics software. Examples of data presentation from tiltmeter applications in studies of landfill covers, characterizations of mine subsidence, and investigations of slope stability are also discussed.

EPA’s Travel Efficiency Method (TEAM) AMPO Presentation

Science.gov (United States)

Presentation describes EPA’s Travel Efficiency Assessment Method (TEAM) assessing potential travel efficiency strategies for reducing travel activity and emissions, includes reduction estimates in Vehicle Miles Traveled in four different geographic areas.

Simplified method for elastic plastic analysis of material presenting bilinear kinematic hardening

International Nuclear Information System (INIS)

Roche, R.

1983-12-01

A simplified method for elastic plastic analysis is presented. Material behavior is assumed to be elastic plastic with bilinear kinematic hardening. The proposed method give a strain-stress field fullfilling material constitutive equations, equations of equilibrium and continuity conditions. This strain-stress is obtained through two linear computations. The first one is the conventional elastic analysis of the body submitted to the applied load. The second one use tangent matrix (tangent Young's modulus and Poisson's ratio) for the determination of an additional stress due to imposed initial strain. Such a method suits finite elements computer codes, the most useful result being plastic strains resulting from the applied loading (load control or deformation control). Obviously, there is not unique solution, for stress-strain field is not depending only of the applied load, but of the load history. Therefore, less pessimistic solutions can be got by one or two additional linear computations [fr

Non-Destructive Evaluation Method Based On Dynamic Invariant Stress Resultants

Directory of Open Access Journals (Sweden)

Zhang Junchi

2015-01-01

Full Text Available Most of the vibration based damage detection methods are based on changes in frequencies, mode shapes, mode shape curvature, and flexibilities. These methods are limited and typically can only detect the presence and location of damage. Current methods seldom can identify the exact severity of damage to structures. This paper will present research in the development of a new non-destructive evaluation method to identify the existence, location, and severity of damage for structural systems. The method utilizes the concept of invariant stress resultants (ISR. The basic concept of ISR is that at any given cross section the resultant internal force distribution in a structural member is not affected by the inflicted damage. The method utilizes dynamic analysis of the structure to simulate direct measurements of acceleration, velocity and displacement simultaneously. The proposed dynamic ISR method is developed and utilized to detect the damage of corresponding changes in mass, damping and stiffness. The objectives of this research are to develop the basic theory of the dynamic ISR method, apply it to the specific types of structures, and verify the accuracy of the developed theory. Numerical results that demonstrate the application of the method will reflect the advanced sensitivity and accuracy in characterizing multiple damage locations.

On the complementary presentation of results of risk studies

International Nuclear Information System (INIS)

Ehrhardt, J.; Bayer, A.

1983-01-01

The presentation of the loss of years of life provides the opportunity to illustrate in complementary way the mortality risks evaluated as part of risk studies. As phase A of the DRS (German risk study nuclear power plants) bears upon the results of the American ''Reactor Safety Study'' (WASH 1400) it does not contain that factor of failure which has only been determined in subsequent studies. Phase B intends to present the results of risk assessments increasingly in form of abridged lifetime. (orig.) [de

A response to: "NIST experts urge caution in use of courtroom evidence presentation method"

OpenAIRE

Morrison, Geoffrey Stewart

2017-01-01

A press release from the National Institute of Standards and Technology (NIST)could potentially impede progress toward improving the analysis of forensic evidence and the presentation of forensic analysis results in courts in the United States and around the world. "NIST experts urge caution in use of courtroom evidence presentation method" was released on October 12, 2017, and was picked up by the phys.org news service. It argues that, except in exceptional cases, the results of forensic ana...

Acceptance of Addiction Prevention Exiting Methods and Presentation of Appropriate Model

Directory of Open Access Journals (Sweden)

Ali Asghar Savad-Kouhi

2006-10-01

Full Text Available Objective: The aim of this study is assessment of acceptance of addiction prevention existing methods and design and present of appropriate model. Materials & Methods: This research has done by survey and desariptive method by using questionnaire we assessed knowledge and belief of people about suggesting and existing methods of addiction prevention and their acceptence and finally design new and appropriate model of addiction prevention. For designing questionnaire, first exports and professors were openly interviewed and according their views final questionnaire was planned. We used questionnaire with 2 open ended and 61 close-ended tests for gathering data. The subjects of research were 2500 persons 13-35 years old that were selected by randomized sampling from 15 provinces. Results: The findings showed that according to people who were studied, they have positive beliefs about prevention methods and their effectiveness. According to findings a good model is inclusive model that able to do in four level: knowledge, change believe and attitude, control and change behavior. Conclusion: The people of study belive that acceptance of suggesting and existing methods of addiction prevention are effective direct and indirect to others, and appropriate model is inclusive model.

Presentation of RELAP5 results on the personal computer

International Nuclear Information System (INIS)

Salamun, I.; Stritar, A.

1991-01-01

DrALF is a program for graphical presentation of RELAP5 results. Results may be displayed in two different forms, as graphs with different zoom capabilities and as drawings or nodalizations with different variables displayed on a background picture. (author)

The present state and future directions of PDF methods

Science.gov (United States)

Pope, S. B.

1992-01-01

The objectives of the workshop are presented in viewgraph format, as is this entire article. The objectives are to discuss the present status and the future direction of various levels of engineering turbulence modeling related to Computational Fluid Dynamics (CFD) computations for propulsion; to assure that combustion is an essential part of propulsion; and to discuss Probability Density Function (PDF) methods for turbulent combustion. Essential to the integration of turbulent combustion models is the development of turbulent model, chemical kinetics, and numerical method. Some turbulent combustion models typically used in industry are the k-epsilon turbulent model, the equilibrium/mixing limited combustion, and the finite volume codes.

Numerical proceessing of radioimmunoassay results using logit-log transformation method

International Nuclear Information System (INIS)

Textoris, R.

1983-01-01

The mathematical model and algorithm are described of the numerical processing of the results of a radioimmunoassay by the logit-log transformation method and by linear regression with weight factors. The limiting value of the curve for zero concentration is optimized with regard to the residual sum by the iterative method by multiple repeats of the linear regression. Typical examples are presented of the approximation of calibration curves. The method proved suitable for all hitherto used RIA sets and is well suited for small computers with internal memory of min. 8 Kbyte. (author)

Comparison of multiple-criteria decision-making methods - results of simulation study

Directory of Open Access Journals (Sweden)

Michał Adamczak

2016-12-01

Full Text Available Background: Today, both researchers and practitioners have many methods for supporting the decision-making process. Due to the conditions in which supply chains function, the most interesting are multi-criteria methods. The use of sophisticated methods for supporting decisions requires the parameterization and execution of calculations that are often complex. So is it efficient to use sophisticated methods? Methods: The authors of the publication compared two popular multi-criteria decision-making methods: the  Weighted Sum Model (WSM and the Analytic Hierarchy Process (AHP. A simulation study reflects these two decision-making methods. Input data for this study was a set of criteria weights and the value of each in terms of each criterion. Results: The iGrafx Process for Six Sigma simulation software recreated how both multiple-criteria decision-making methods (WSM and AHP function. The result of the simulation was a numerical value defining the preference of each of the alternatives according to the WSM and AHP methods. The alternative producing a result of higher numerical value  was considered preferred, according to the selected method. In the analysis of the results, the relationship between the values of the parameters and the difference in the results presented by both methods was investigated. Statistical methods, including hypothesis testing, were used for this purpose. Conclusions: The simulation study findings prove that the results obtained with the use of two multiple-criteria decision-making methods are very similar. Differences occurred more frequently in lower-value parameters from the "value of each alternative" group and higher-value parameters from the "weight of criteria" group.

Comparison results on preconditioned SOR-type iterative method for Z-matrices linear systems

Science.gov (United States)

Wang, Xue-Zhong; Huang, Ting-Zhu; Fu, Ying-Ding

2007-09-01

In this paper, we present some comparison theorems on preconditioned iterative method for solving Z-matrices linear systems, Comparison results show that the rate of convergence of the Gauss-Seidel-type method is faster than the rate of convergence of the SOR-type iterative method.

Overview of mycotoxin methods, present status and future needs.

Science.gov (United States)

Gilbert, J

1999-01-01

This article reviews current requirements for the analysis for mycotoxins in foods and identifies legislative as well as other factors that are driving development and validation of new methods. New regulatory limits for mycotoxins and analytical quality assurance requirements for laboratories to only use validated methods are seen as major factors driving developments. Three major classes of methods are identified which serve different purposes and can be categorized as screening, official and research. In each case the present status and future needs are assessed. In addition to an overview of trends in analytical methods, some other areas of analytical quality assurance such as participation in proficiency testing and reference materials are identified.

Two different hematocrit detection methods: Different methods, different results?

Directory of Open Access Journals (Sweden)

Schuepbach Reto A

2010-03-01

Full Text Available Abstract Background Less is known about the influence of hematocrit detection methodology on transfusion triggers. Therefore, the aim of the present study was to compare two different hematocrit-assessing methods. In a total of 50 critically ill patients hematocrit was analyzed using (1 blood gas analyzer (ABLflex 800 and (2 the central laboratory method (ADVIA® 2120 and compared. Findings Bland-Altman analysis for repeated measurements showed a good correlation with a bias of +1.39% and 2 SD of ± 3.12%. The 24%-hematocrit-group showed a correlation of r2 = 0.87. With a kappa of 0.56, 22.7% of the cases would have been transfused differently. In the-28%-hematocrit group with a similar correlation (r2 = 0.8 and a kappa of 0.58, 21% of the cases would have been transfused differently. Conclusions Despite a good agreement between the two methods used to determine hematocrit in clinical routine, the calculated difference of 1.4% might substantially influence transfusion triggers depending on the employed method.

Development and application of a new deterministic method for calculating computer model result uncertainties

International Nuclear Information System (INIS)

Maerker, R.E.; Worley, B.A.

1989-01-01

Interest in research into the field of uncertainty analysis has recently been stimulated as a result of a need in high-level waste repository design assessment for uncertainty information in the form of response complementary cumulative distribution functions (CCDFs) to show compliance with regulatory requirements. The solution to this problem must obviously rely on the analysis of computer code models, which, however, employ parameters that can have large uncertainties. The motivation for the research presented in this paper is a search for a method involving a deterministic uncertainty analysis approach that could serve as an improvement over those methods that make exclusive use of statistical techniques. A deterministic uncertainty analysis (DUA) approach based on the use of first derivative information is the method studied in the present procedure. The present method has been applied to a high-level nuclear waste repository problem involving use of the codes ORIGEN2, SAS, and BRINETEMP in series, and the resulting CDF of a BRINETEMP result of interest is compared with that obtained through a completely statistical analysis

New method of scoliosis assessment: preliminary results using computerized photogrammetry.

Science.gov (United States)

Aroeira, Rozilene Maria Cota; Leal, Jefferson Soares; de Melo Pertence, Antônio Eustáquio

2011-09-01

A new method for nonradiographic evaluation of scoliosis was independently compared with the Cobb radiographic method, for the quantification of scoliotic curvature. To develop a protocol for computerized photogrammetry, as a nonradiographic method, for the quantification of scoliosis, and to mathematically relate this proposed method with the Cobb radiographic method. Repeated exposure to radiation of children can be harmful to their health. Nevertheless, no nonradiographic method until now proposed has gained popularity as a routine method for evaluation, mainly due to a low correspondence to the Cobb radiographic method. Patients undergoing standing posteroanterior full-length spine radiographs, who were willing to participate in this study, were submitted to dorsal digital photography in the orthostatic position with special surface markers over the spinous process, specifically the vertebrae C7 to L5. The radiographic and photographic images were sent separately for independent analysis to two examiners, trained in quantification of scoliosis for the types of images received. The scoliosis curvature angles obtained through computerized photogrammetry (the new method) were compared to those obtained through the Cobb radiographic method. Sixteen individuals were evaluated (14 female and 2 male). All presented idiopathic scoliosis, and were between 21.4 ± 6.1 years of age; 52.9 ± 5.8 kg in weight; 1.63 ± 0.05 m in height, with a body mass index of 19.8 ± 0.2. There was no statistically significant difference between the scoliosis angle measurements obtained in the comparative analysis of both methods, and a mathematical relationship was formulated between both methods. The preliminary results presented demonstrate equivalence between the two methods. More studies are needed to firmly assess the potential of this new method as a coadjuvant tool in the routine following of scoliosis treatment.

Delayed Presentation of Traumatic Diaphragmatic Hernia: The Evaluation of Surgical Treatment Results

Directory of Open Access Journals (Sweden)

Ali Sadrizadeh

2015-06-01

Full Text Available Introduction: Diaphragmatic hernia could be caused by congenital disorders, blunt trauma or penetrating injuries. The diagnosis of traumatic diaphragmatic hernia is normally neglected during the first presentation leading to late complications and considerably increased mortality and morbidity among the patients. Materials and Methods: In this retrospective, descriptive study, we reviewed the medical records of patients presented with traumatic diaphragmatic hernia who had undergone surgical operations between 1982-2015 in Ghaem Hospital and Omid Hospital affiliated to Mashhad University of Medical Sciences, Iran. The studied variables included age, gender, clinical symptoms, location of hernia, involved organs, type of imaging modalities, surgical techniques, length of hospital stay, mortality rate and surgical complications. Results: In this study, 38 patients were diagnosed with traumatic diaphragmatic hernia consisting of 28 men and 10 women. In total, 79% and 21% of the patients suffered from penetrating trauma and blunt trauma, respectively. In addition, left-sided, right-sided and bilateral hernias were present in 33%, 4% and 1% of the patients, respectively. The most frequently herniated organ was the stomach, and the most common clinical symptoms were abdominal pain (84% and dyspnea (53%. Initially, chest radiographs were performed on all the patients, and thoracotomy was performed to repair diaphragmatic tears in all the cases (100%. In this study, 3 patients had previously undergone Hartmann’s operation for gangrenous herniated colon, and devolvulation of gastric volvulus had also been performed on 3 patients. The main post-operative complications were reported to be pneumonia and respiratory insufficiency (2 cases, and the mean length of hospital stay was 6 days (5-8 days which was longer (1-2 months in patients with gangrenous bowel (3 patients. Furthermore, no mortality was reported during the course of hospitalization in these

Multiband discrete ordinates method: formalism and results

International Nuclear Information System (INIS)

Luneville, L.

1998-06-01

The multigroup discrete ordinates method is a classical way to solve transport equation (Boltzmann) for neutral particles. Self-shielding effects are not correctly treated due to large variations of cross sections in a group (in the resonance range). To treat the resonance domain, the multiband method is introduced. The main idea is to divide the cross section domain into bands. We obtain the multiband parameters using the moment method; the code CALENDF provides probability tables for these parameters. We present our implementation in an existing discrete ordinates code: SN1D. We study deep penetration benchmarks and show the improvement of the method in the treatment of self-shielding effects. (author)

Connecting Past with Present: A Mixed-Methods Science Ethics Course and its Evaluation.

Science.gov (United States)

Semendeferi, Ioanna; Tsiamyrtzis, Panagiotis; Dcosta, Malcolm; Pavlidis, Ioannis

2016-02-01

We present a graduate science ethics course that connects cases from the historical record to present realities and practices in the areas of social responsibility, authorship, and human/animal experimentation. This content is delivered with mixed methods, including films, debates, blogging, and practicum; even the instructional team is mixed, including a historian of science and a research scientist. What really unites all of the course's components is the experiential aspect: from acting in historical debates to participating in the current scientific enterprise. The course aims to change the students' culture into one deeply devoted to the science ethics cause. To measure the sought after cultural change, we developed and validated a relevant questionnaire. Results of this questionnaire from students who took the course, demonstrate that the course had the intended effect on them. Furthermore, results of this questionnaire from controls indicate the need for cultural change in that cohort. All these quantitative results are reinforced by qualitative outcomes.

Application of the DSA preconditioned GMRES formalism to the method of characteristics - First results

International Nuclear Information System (INIS)

Le Tellier, R.; Hebert, A.

2004-01-01

The method of characteristics is well known for its slow convergence; consequently, as it is often done for SN methods, the Generalized Minimal Residual approach (GMRES) has been investigated for its practical implementation and its high reliability. GMRES is one of the most effective Krylov iterative methods to solve large linear systems. Moreover, the system has been 'left preconditioned' with the Algebraic Collapsing Acceleration (ACA) a variant of the Diffusion Synthetic Acceleration (DSA) based on I. Suslov's former works. This paper presents the first numerical results of these methods in 2D geometries with material discontinuities. Indeed, previous investigations have shown a degraded effectiveness of Diffusion Synthetic Accelerations with this kind of geometries. Results are presented for 9 x 9 Cartesian assemblies in terms of the speed of convergence of the inner iterations (fixed source) of the method of characteristics. It shows a significant improvement on the convergence rate. (authors)

SPACE CHARGE SIMULATION METHODS INCORPORATED IN SOME MULTI - PARTICLE TRACKING CODES AND THEIR RESULTS COMPARISON

International Nuclear Information System (INIS)

BEEBE - WANG, J.; LUCCIO, A.U.; D IMPERIO, N.; MACHIDA, S.

2002-01-01

Space charge in high intensity beams is an important issue in accelerator physics. Due to the complicity of the problems, the most effective way of investigating its effect is by computer simulations. In the resent years, many space charge simulation methods have been developed and incorporated in various 2D or 3D multi-particle-tracking codes. It has becoming necessary to benchmark these methods against each other, and against experimental results. As a part of global effort, we present our initial comparison of the space charge methods incorporated in simulation codes ORBIT++, ORBIT and SIMPSONS. In this paper, the methods included in these codes are overviewed. The simulation results are presented and compared. Finally, from this study, the advantages and disadvantages of each method are discussed

SPACE CHARGE SIMULATION METHODS INCORPORATED IN SOME MULTI - PARTICLE TRACKING CODES AND THEIR RESULTS COMPARISON.

Energy Technology Data Exchange (ETDEWEB)

BEEBE - WANG,J.; LUCCIO,A.U.; D IMPERIO,N.; MACHIDA,S.

2002-06-03

Space charge in high intensity beams is an important issue in accelerator physics. Due to the complicity of the problems, the most effective way of investigating its effect is by computer simulations. In the resent years, many space charge simulation methods have been developed and incorporated in various 2D or 3D multi-particle-tracking codes. It has becoming necessary to benchmark these methods against each other, and against experimental results. As a part of global effort, we present our initial comparison of the space charge methods incorporated in simulation codes ORBIT++, ORBIT and SIMPSONS. In this paper, the methods included in these codes are overviewed. The simulation results are presented and compared. Finally, from this study, the advantages and disadvantages of each method are discussed.

Economic Inequality in Presenting Vision in Shahroud, Iran: Two Decomposition Methods

Directory of Open Access Journals (Sweden)

Asieh Mansouri

2018-01-01

Full Text Available Background Visual acuity, like many other health-related problems, does not have an equal distribution in terms of socio-economic factors. We conducted this study to estimate and decompose economic inequality in presenting visual acuity using two methods and to compare their results in a population aged 40-64 years in Shahroud, Iran. Methods: The data of 5188 participants in the first phase of the Shahroud Cohort Eye Study, performed in 2009, were used for this study. Our outcome variable was presenting vision acuity (PVA that was measured using LogMAR (logarithm of the minimum angle of resolution. The living standard variable used for estimation of inequality was the economic status and was constructed by principal component analysis on home assets. Inequality indices were concentration index and the gap between low and high economic groups. We decomposed these indices by the concentration index and BlinderOaxaca decomposition approaches respectively and compared the results. Results The concentration index of PVA was -0.245 (95% CI: -0.278, -0.212. The PVA gap between groups with a high and low economic status was 0.0705 and was in favor of the high economic group. Education, economic status, and age were the most important contributors of inequality in both concentration index and Blinder-Oaxaca decomposition. Percent contribution of these three factors in the concentration index and Blinder-Oaxaca decomposition was 41.1% vs. 43.4%, 25.4% vs. 19.1% and 15.2% vs. 16.2%, respectively. Other factors including gender, marital status, employment status and diabetes had minor contributions. Conclusion This study showed that individuals with poorer visual acuity were more concentrated among people with a lower economic status. The main contributors of this inequality were similar in concentration index and Blinder-Oaxaca decomposition. So, it can be concluded that setting appropriate interventions to promote the literacy and income level in people

How the RNA isolation method can affect microRNA microarray results

DEFF Research Database (Denmark)

Podolska, Agnieszka; Kaczkowski, Bogumil; Litman, Thomas

2011-01-01

RNA microarray analysis on porcine brain tissue. One method is a phenol-guanidine isothiocyanate-based procedure that permits isolation of total RNA. The second method, miRVana™ microRNA isolation, is column based and recovers the small RNA fraction alone. We found that microarray analyses give different results...... that depend on the RNA fraction used, in particular because some microRNAs appear very sensitive to the RNA isolation method. We conclude that precautions need to be taken when comparing microarray studies based on RNA isolated with different methods.......The quality of RNA is crucial in gene expression experiments. RNA degradation interferes in the measurement of gene expression, and in this context, microRNA quantification can lead to an incorrect estimation. In the present study, two different RNA isolation methods were used to perform micro...

Methods of removing uranium from drinking water. 1. A literature survey. 2. Present municipal water treatment and potential removal methods

International Nuclear Information System (INIS)

Drury, J.S.; Michelson, D.; Ensminger, J.T.; Lee, S.Y.; White, S.K.

1982-12-01

Literature was searched for methods of removing uranium from drinking water. U.S. manufacturers and users of water-treatment equipment and products were also contacted regarding methods of removing uranium from potable water. Based on the results of these surveys, it was recommended that untreated, partially treated, and finished water samples from municipal water-treatment facilities be analyzed to determine the extent of removal of uranium by presently used procedures, and that additional laboratory studies be performed to determine what changes are needed to maximize the effectiveness of treatments that are already in use in existing water-treatment plants

Present-day Problems and Methods of Optimization in Mechatronics

Directory of Open Access Journals (Sweden)

Tarnowski Wojciech

2017-06-01

Full Text Available It is justified that design is an inverse problem, and the optimization is a paradigm. Classes of design problems are proposed and typical obstacles are recognized. Peculiarities of the mechatronic designing are specified as a proof of a particle importance of optimization in the mechatronic design. Two main obstacles of optimization are discussed: a complexity of mathematical models and an uncertainty of the value system, in concrete case. Then a set of non-standard approaches and methods are presented and discussed, illustrated by examples: a fuzzy description, a constraint-based iterative optimization, AHP ranking method and a few MADM functions in Matlab.

Trojan Horse Method: Recent Results

International Nuclear Information System (INIS)

Pizzone, R. G.; Spitaleri, C.

2008-01-01

Owing the presence of the Coulomb barrier at astrophysically relevant kinetic energies, it is very difficult, or sometimes impossible to measure astrophysical reaction rates in laboratory. This is why different indirect techniques are being used along with direct measurements. The THM is unique indirect technique allowing one measure astrophysical rearrangement reactions down to astrophysical relevant energies. The basic principle and a review of the main application of the Trojan Horse Method are presented. The applications aiming at the extraction of the bare S b (E) astrophysical factor and electron screening potentials U e for several two body processes are discussed

Comparison of the analysis result between two laboratories using different methods

International Nuclear Information System (INIS)

Sri Murniasih; Agus Taftazani

2017-01-01

Comparison of the analysis result of volcano ash sample between two laboratories using different analysis methods. The research aims to improve the testing laboratory quality and cooperate with the testing laboratory from other country. Samples were tested at the Center for Accelerator of Science and Technology (CAST)-NAA laboratory using NAA, while at the University of Texas (UT) USA using ICP-MS and ENAA method. From 12 elements of target, CAST-NAA able to present 11 elements of data analysis. The comparison results shows that the analysis of the K, Mn, Ti and Fe elements from both laboratories have a very good comparison and close one to other. It is known from RSD values and correlation coefficients of the both laboratories analysis results. While observed of the results difference known that the analysis results of Al, Na, K, Fe, V, Mn, Ti, Cr and As elements from both laboratories is not significantly different. From 11 elements were reported, only Zn which have significantly different values for both laboratories. (author)

The Trojan Horse method for nuclear astrophysics: Recent results for direct reactions

International Nuclear Information System (INIS)

Tumino, A.; Gulino, M.; Spitaleri, C.; Cherubini, S.; Romano, S.; Cognata, M. La; Pizzone, R. G.; Rapisarda, G. G.; Lamia, L.

2014-01-01

The Trojan Horse method is a powerful indirect technique to determine the astrophysical factor for binary rearrangement processes A+x→b+B at astrophysical energies by measuring the cross section for the Trojan Horse (TH) reaction A+a→B+b+s in quasi free kinematics. The Trojan Horse Method has been successfully applied to many reactions of astrophysical interest, both direct and resonant. In this paper, we will focus on direct sub-processes. The theory of the THM for direct binary reactions will be shortly presented based on a few-body approach that takes into account the off-energy-shell effects and initial and final state interactions. Examples of recent results will be presented to demonstrate how THM works experimentally

The Trojan Horse method for nuclear astrophysics: Recent results for direct reactions

Energy Technology Data Exchange (ETDEWEB)

Tumino, A.; Gulino, M. [Laboratori Nazionali del Sud, Istituto Nazionale di Fisica Nucleare, Catania, Italy and Università degli Studi di Enna Kore, Enna (Italy); Spitaleri, C.; Cherubini, S.; Romano, S. [Laboratori Nazionali del Sud, Istituto Nazionale di Fisica Nucleare, Catania, Italy and Dipartimento di Fisica e Astronomia, Università di Catania, Catania (Italy); Cognata, M. La; Pizzone, R. G.; Rapisarda, G. G. [Laboratori Nazionali del Sud, Istituto Nazionale di Fisica Nucleare, Catania (Italy); Lamia, L. [Dipartimento di Fisica e Astronomia, Università di Catania, Catania (Italy)

2014-05-09

The Trojan Horse method is a powerful indirect technique to determine the astrophysical factor for binary rearrangement processes A+x→b+B at astrophysical energies by measuring the cross section for the Trojan Horse (TH) reaction A+a→B+b+s in quasi free kinematics. The Trojan Horse Method has been successfully applied to many reactions of astrophysical interest, both direct and resonant. In this paper, we will focus on direct sub-processes. The theory of the THM for direct binary reactions will be shortly presented based on a few-body approach that takes into account the off-energy-shell effects and initial and final state interactions. Examples of recent results will be presented to demonstrate how THM works experimentally.

Lecture Presentations

International Nuclear Information System (INIS)

2007-01-01

The Heavy-Ion Collisions in the LHC workshop held in Cracow from 18 to 18 May 2007. The main subject of the workshop was to present the newest results of research provided at CERN LHC collider. Additionally some theoretical models and methods used for presented data analysis were discussed

Social network analysis: Presenting an underused method for nursing research.

Science.gov (United States)

Parnell, James Michael; Robinson, Jennifer C

2018-06-01

This paper introduces social network analysis as a versatile method with many applications in nursing research. Social networks have been studied for years in many social science fields. The methods continue to advance but remain unknown to most nursing scholars. Discussion paper. English language and interpreted literature was searched from Ovid Healthstar, CINAHL, PubMed Central, Scopus and hard copy texts from 1965 - 2017. Social network analysis first emerged in nursing literature in 1995 and appears minimally through present day. To convey the versatility and applicability of social network analysis in nursing, hypothetical scenarios are presented. The scenarios are illustrative of three approaches to social network analysis and include key elements of social network research design. The methods of social network analysis are underused in nursing research, primarily because they are unknown to most scholars. However, there is methodological flexibility and epistemological versatility capable of supporting quantitative and qualitative research. The analytic techniques of social network analysis can add new insight into many areas of nursing inquiry, especially those influenced by cultural norms. Furthermore, visualization techniques associated with social network analysis can be used to generate new hypotheses. Social network analysis can potentially uncover findings not accessible through methods commonly used in nursing research. Social networks can be analysed based on individual-level attributes, whole networks and subgroups within networks. Computations derived from social network analysis may stand alone to answer a research question or incorporated as variables into robust statistical models. © 2018 John Wiley & Sons Ltd.

Presentation of RTE results 2003

International Nuclear Information System (INIS)

2003-01-01

In 2003, RTE recorded a clear improvement in its financial results, and continued its debt reduction programme. The financial year 2003 was marked by a clear improvement in RTE's financial performance: results exceeded objectives, with turnover growing strongly, net income reached levels almost three times higher than those recorded in 2002, the economic rate of return rose to 7.1%, and debt was reduced by 470 Meuros. These results are explained by the substantial improvement in productivity, which has risen by 5% per year on average over the last three years. Net income has almost tripled due to RTE's improved productivity completed by a significant rise in its turnover and stabilizing operating costs RTE's finances therefore remain healthy, enabling the company to continue its debt reduction programme. Satisfactory economic and financial rates of return. Deadlines facing RTE in 2004: in application of the second European Directive, adopted on 26 June 2003, RTE faces two major deadlines in 2004: - the implementation of the 2. phase in the process of opening up the French electricity market, - its legal independence. On 1 July 2004, the market will be opened up to competition for all professional customers. At that date RTE, like all other electricity transmission system operators (TSOs) in the European Union, should be a legally independent body. The new central role of TSOs in Europe: how are electricity transmission system operators in other EU countries organised?

Solar neutrino results and present status

International Nuclear Information System (INIS)

Gorbachev, V.V.; Abdurashitov, J.N.; Gavrin, V.N.; Girin, S.V.; Gurkina, P.P.; Ibragimova, T.V.; Kalikhov, A.V.; Khairnasov, N.G.; Knodel, T.V.; Mirmov, I.N.; Shikhin, A.A.; Veretenkin, E.P.; Vermul, V.M.; Yants, V.E.; Zatsepin, G.T.; Bowles, T.J.; Teasdale, W.A.; Cherry, M.L.; Cleveland, B.T.; Elliott, S.R.

2002-01-01

The solar neutrino capture rate measured by the Russian-American Gallium Experiment on a metallic gallium target SAGE during the time from January 1990 through December 2000 is 77.0 +6.2 -6.2 +3.5 -3.0 SNU, where the uncertainties are statistical and systematic, respectively. The experimental procedures and data analysis are presented

Radioimmunological determination of plasma progesterone. Methods - Results - Indications

International Nuclear Information System (INIS)

Gonon-Estrangin, Chantal.

1978-10-01

The aim of this work is to describe the radioimmunological determination of plasma progesterone carried out at the hormonology Laboratory of the Grenoble University Hospital Centre (Professor E. Chambaz), to compare our results with those of the literature and to present the main clinical indications of this analysis. The measurement method has proved reproducible, specific (the steroid purification stage is unnecessary) and sensitive (detection: 10 picograms of progesterone per tube). In seven normally menstruating women our results agree with published values: (in nanograms per millilitre: ng/ml) 0.07 ng/ml to 0.9 ng/ml in the follicular phase, from the start of menstruation until ovulation, then rapid increase at ovulation with a maximum in the middle of the luteal phase (our values for this maximum range from 7.9 ng/ml to 21.7 ng/ml) and gradual drop in progesterone secretion until the next menstrual period. In gynecology the radioimmunoassay of plasma progesterone is valuable for diagnostic and therapeutic purposes: - to diagnosis the absence of corpus luteum, - to judge the effectiveness of an ovulation induction treatment [fr

GRS Method for Uncertainty and Sensitivity Evaluation of Code Results and Applications

International Nuclear Information System (INIS)

Glaeser, H.

2008-01-01

During the recent years, an increasing interest in computational reactor safety analysis is to replace the conservative evaluation model calculations by best estimate calculations supplemented by uncertainty analysis of the code results. The evaluation of the margin to acceptance criteria, for example, the maximum fuel rod clad temperature, should be based on the upper limit of the calculated uncertainty range. Uncertainty analysis is needed if useful conclusions are to be obtained from best estimate thermal-hydraulic code calculations, otherwise single values of unknown accuracy would be presented for comparison with regulatory acceptance limits. Methods have been developed and presented to quantify the uncertainty of computer code results. The basic techniques proposed by GRS are presented together with applications to a large break loss of coolant accident on a reference reactor as well as on an experiment simulating containment behaviour

New Learning Method of a Lecture of ‘Machine Fabrication’ by Self-study with Investigation and Presentation Incorporated

Science.gov (United States)

Kasuga, Yukio

A new teaching method was developed in learning ‘machine fabrication’ for the undergraduate students. This consists of a few times of lectures, grouping, decision of industrial products which each group wants to investigate, investigation work by library books and internet, arrangement of data containing characteristics of the products, employed materials and processing methods, presentation, discussions and revision followed by another presentation. This new method is derived from one of the Finland‧s way of primary school education. Their way of education is believed to have boosted up to the top ranking in PISA tests by OECD. After starting the new way of learning, students have fresh impressions on this lesson, especially for self-study, the way of investigation, collaborate work and presentation. Also, after four years of implementation, some improvements have been made including less use of internet, and determination of products and fabricating methods in advance which should be investigated. By this, students‧ lecture assessment shows further encouraging results.

A holographic method for investigating cylindrical symmetry plasmas resulting from electric discharges

International Nuclear Information System (INIS)

Rosu, N.; Ralea, M.; Foca, M.; Iova, I.

1992-01-01

A new method based on holographic interferometry in real time with reference fringes for diagnosing gas electric discharges in cylindrical symmetry tubes is presented. A method for obtaining and quantitatively investigating interferograms obtained with a video camera is described. By studying the resulting images frame by frame and introducing the measurements into an adequate computer programme one gets a graphical recording of the radial distribution of the charged particle concentration in the plasma in any region of the tube at a given time, as well as their axial distribution. The real time evolution of certain phenomena occurring in the discharge tube can also be determined by this non-destructive method. The method is used for electric discharges in Ar at average pressures in a discharge tube with hollow cathode effect. (Author)

The FODA-TDMA satellite access scheme - Presentation, study of the system, and results

Science.gov (United States)

Celandroni, Nedo; Ferro, Erina

1991-12-01

A description is given of FODA-TDMA, a satellite access scheme designed for mixed traffic. The study of the system is presented and the choice of some parameters is justified. A simplified analytic solution is found, describing the steady-state behavior of the system. Some results of the simulation tests for an already existing hardware environment are also presented for the channel speeds of 2 and 8 Mb/s, considering both the stationary and the transient cases. The results of the experimentation at 2 Mb/s on the satellite Eutelsat-F2 are also presented and compared with the results of the simulation.

Experimental Results and Numerical Simulation of the Target RCS using Gaussian Beam Summation Method

Directory of Open Access Journals (Sweden)

Ghanmi Helmi

2018-05-01

Full Text Available This paper presents a numerical and experimental study of Radar Cross Section (RCS of radar targets using Gaussian Beam Summation (GBS method. The purpose GBS method has several advantages over ray method, mainly on the caustic problem. To evaluate the performance of the chosen method, we started the analysis of the RCS using Gaussian Beam Summation (GBS and Gaussian Beam Launching (GBL, the asymptotic models Physical Optic (PO, Geometrical Theory of Diffraction (GTD and the rigorous Method of Moment (MoM. Then, we showed the experimental validation of the numerical results using experimental measurements which have been executed in the anechoic chamber of Lab-STICC at ENSTA Bretagne. The numerical and experimental results of the RCS are studied and given as a function of various parameters: polarization type, target size, Gaussian beams number and Gaussian beams width.

A Systematic Review of Barriers to Breast Cancer Care in Developing Countries Resulting in Delayed Patient Presentation

Directory of Open Access Journals (Sweden)

Ketan Sharma

2012-01-01

Full Text Available Background. Within the developing world, many personal, sociocultural, and economic factors cause delayed patient presentation, a prolonged interval from initial symptom discovery to provider presentation. Understanding these barriers to care is crucial to optimizing interventions that pre-empt patient delay. Methods. A systematic review was conducted querying: PubMed, Embase, Web of Science, CINAHL, Cochrane Library, J East, CAB, African Index Medicus, and LiLACS. Of 763 unique abstracts, 122 were extracted for full review and 13 included in final analysis. Results. Studies posed variable risks of bias and produced mixed results. There is strong evidence that lower education level and lesser income status contribute to patient delay. There is weaker and, sometimes, contradictory evidence that other factors may also contribute. Discussion. Poverty emerges as the underlying common denominator preventing earlier presentation in these settings. The evidence for sociocultural variables is less strong, but may reflect current paucity of high-quality research. Conflicting results may be due to heterogeneity of the developing world itself. Conclusion. Future research is required that includes patients with and without delay, utilizes a validated questionnaire, and controls for potential confounders. Current evidence suggests that interventions should primarily increase proximal and affordable healthcare access and secondarily enhance breast cancer awareness, to productively reduce patient delay.

The Presentation of Self in Letters of Application: A Mixed-Method Approach

Science.gov (United States)

Soroko, Emilia

2012-01-01

The application letter, as the first phase of employment-seeking, is an opportunity for a job applicant to make a favorable impression on a potential employer. In the current study, the author used a mixed-method approach to empirically explore strategies for self-presentation in job application letters and determine the methods used in the…

Evolution of different reaction methods resulting in the formation of AgI125 for use in brachytherapy sources

International Nuclear Information System (INIS)

Souza, C.D.; Peleias Jr, F.S.; Rostelato, M.E.C.M.; Zeituni, C.A.; Benega, M.A.G.; Tiezzi, R.; Mattos, F.R.; Rodrigues, B.T.; Oliveira, T.B.; Feher, A.; Moura, J.A.; Costa, O.L.

2014-01-01

Prostate cancer represents about 10% of all cases of cancer in the world. Brachytherapy has been extensively used in the early and intermediate stages of the illness. The radiotherapy method reduces the damage probability to surrounding healthy tissues. The present study compares several deposition methods of iodine-125 on silver substrate (seed core), in order to choose the most suitable one to be implemented at IPEN. Four methods were selected: method 1 (assay based on electrodeposition) which presented efficiency of 65.16%; method 2 (assay based on chemical reactions, developed by David Kubiatowicz) which presented efficiency of 70.80%; method 3 (chemical reaction based on the methodology developed by Dr. Maria Elisa Rostelato) which presented efficiency of 55.80%; new method developed by IPEN with 90.5% efficiency. Based on the results, the new method is the suggested one to be implemented. (authors)

Conservative treatment of idiopathic scoliosis according to FITS concept: presentation of the method and preliminary, short term radiological and clinical results based on SOSORT and SRS criteria

Science.gov (United States)

2011-01-01

Background Conservative scoliosis therapy according to the FITS Concept is applied as a unique treatment or in combination with corrective bracing. The aim of the study was to present author's method of diagnosis and therapy for idiopathic scoliosis FITS-Functional Individual Therapy of Scoliosis and to analyze the early results of FITS therapy in a series of consecutive patients. Methods The analysis comprised separately: (1) single structural thoracic, thoracolumbar or lumbar curves and (2) double structural scoliosis-thoracic and thoracolumbar or lumbar curves. The Cobb angle and Risser sign were analyzed at the initial stage and at the 2.8-year follow-up. The percentage of patients improved (defined as decrease of Cobb angle of more than 5 degrees), stable (+/- 5 degrees), and progressed (increase of Cobb angle of more than 5 degrees) was calculated. The clinical assessment comprised: the Angle of Trunk Rotation (ATR) initial and follow-up value, the plumb line imbalance, the scapulae level and the distance from the apical spinous process of the primary curve to the plumb line. Results In the Group A: (1) in single structural scoliosis 50,0% of patients improved, 46,2% were stable and 3,8% progressed, while (2) in double scoliosis 50,0% of patients improved, 30,8% were stable and 19,2% progressed. In the Group B: (1) in single scoliosis 20,0% of patients improved, 80,0% were stable, no patient progressed, while (2) in double scoliosis 28,1% of patients improved, 46,9% were stable and 25,0% progressed. Conclusion Best results were obtained in 10-25 degrees scoliosis which is a good indication to start therapy before more structural changes within the spine establish. PMID:22122964

Conservative treatment of idiopathic scoliosis according to FITS concept: presentation of the method and preliminary, short term radiological and clinical results based on SOSORT and SRS criteria

Directory of Open Access Journals (Sweden)

Białek Marianna

2011-11-01

Full Text Available Abstract Background Conservative scoliosis therapy according to the FITS Concept is applied as a unique treatment or in combination with corrective bracing. The aim of the study was to present author's method of diagnosis and therapy for idiopathic scoliosis FITS-Functional Individual Therapy of Scoliosis and to analyze the early results of FITS therapy in a series of consecutive patients. Methods The analysis comprised separately: (1 single structural thoracic, thoracolumbar or lumbar curves and (2 double structural scoliosis-thoracic and thoracolumbar or lumbar curves. The Cobb angle and Risser sign were analyzed at the initial stage and at the 2.8-year follow-up. The percentage of patients improved (defined as decrease of Cobb angle of more than 5 degrees, stable (+/- 5 degrees, and progressed (increase of Cobb angle of more than 5 degrees was calculated. The clinical assessment comprised: the Angle of Trunk Rotation (ATR initial and follow-up value, the plumb line imbalance, the scapulae level and the distance from the apical spinous process of the primary curve to the plumb line. Results In the Group A: (1 in single structural scoliosis 50,0% of patients improved, 46,2% were stable and 3,8% progressed, while (2 in double scoliosis 50,0% of patients improved, 30,8% were stable and 19,2% progressed. In the Group B: (1 in single scoliosis 20,0% of patients improved, 80,0% were stable, no patient progressed, while (2 in double scoliosis 28,1% of patients improved, 46,9% were stable and 25,0% progressed. Conclusion Best results were obtained in 10-25 degrees scoliosis which is a good indication to start therapy before more structural changes within the spine establish.

Visual Display of Scientific Studies, Methods, and Results

Science.gov (United States)

Saltus, R. W.; Fedi, M.

2015-12-01

The need for efficient and effective communication of scientific ideas becomes more urgent each year.A growing number of societal and economic issues are tied to matters of science - e.g., climate change, natural resource availability, and public health. Societal and political debate should be grounded in a general understanding of scientific work in relevant fields. It is difficult for many participants in these debates to access science directly because the formal method for scientific documentation and dissemination is the journal paper, generally written for a highly technical and specialized audience. Journal papers are very effective and important for documentation of scientific results and are essential to the requirements of science to produce citable and repeatable results. However, journal papers are not effective at providing a quick and intuitive summary useful for public debate. Just as quantitative data are generally best viewed in graphic form, we propose that scientific studies also can benefit from visual summary and display. We explore the use of existing methods for diagramming logical connections and dependencies, such as Venn diagrams, mind maps, flow charts, etc., for rapidly and intuitively communicating the methods and results of scientific studies. We also discuss a method, specifically tailored to summarizing scientific papers that we introduced last year at AGU. Our method diagrams the relative importance and connections between data, methods/models, results/ideas, and implications/importance using a single-page format with connected elements in these four categories. Within each category (e.g., data) the spatial location of individual elements (e.g., seismic, topographic, gravity) indicates relative novelty (e.g., are these new data?) and importance (e.g., how critical are these data to the results of the paper?). The goal is to find ways to rapidly and intuitively share both the results and the process of science, both for communication

Presentation of RTE results 2003

International Nuclear Information System (INIS)

2004-01-01

For RTE, the financial year 2003 was marked by a number of achievements: our financial performances registered a clear improvement, above objectives, with turnover growing strongly; net income reached levels almost three times higher than those recorded in 2002; the economic rate of return rose to 7.1%; and debt was reduced by 470 Meuros. These results are explained by the substantial improvement in productivity, which has risen by 5% per year on average over the last three years

Analysis of technologies for natural gas transportation in Brazil: results comparison of the application of payback and NPV (Net Present Value) methods; Analise de tecnologias de transporte de gas natural no Brasil: comparacao dos resultados da aplicacao dos metodos 'payback' e VPL (Valor Presente Liquido)

Energy Technology Data Exchange (ETDEWEB)

Baioco, Juliana Souza; Santarem, Clarissa Andrade [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Dept. de Engenharia de Petroleo; Bone, Rosemarie Broeker; Ferreira Filho, Virgilio Jose Martins [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Dept. de Engenharia Industrial

2008-07-01

The increased demand for natural gas leads to global integration of markets, leading to decisions that cover the various technologies of transportation, noting the specific locations. The transport of natural gas considered more traditional (Liquefied Natural Gas and Pipeline) often unviable economically areas of operation due to cost. In this case, there are alternative technologies to reduce those costs. The article is to compare the technologies of transport, using the methodology of the Net Present Value (VPL) to identify one that has more positive VPL, which is the most profitable. Thus, in search of validate the results of SUBERO et al. (2004) for gas transport by Pipelines, Liquefied Natural Gas and Compressed Natural Gas. In addition, they are compared these results with the method of VPL and with the economic analysis presented in using the payback period of CHANG (2001) and SANTAREM et al. (2007). It was found that the results obtained in Brazil were identical to those obtained by CHANG (2001) and SUBERO et al. (2007), saving only some differences in magnitude due to the specific characteristics of the Brazilian economy. In other words, for the Brazilian case, the technology of Compressed Natural Gas (CNG) was the most economically viable with the method of VPL, followed by technology, Pipeline and Liquefied Natural Gas (LNG), regardless of the interest rates of 10% and 6.5% and periods of 20 and 30 years. The contribution of this work is to show that despite of the method, payback or VPL, the various alternatives for transporting natural gas to Brazil have the same ranking and economic viability. (author)

A new method for evaluation and correction of thermal reactor power and present operational applications

International Nuclear Information System (INIS)

Langenstein, M.; Streit, S.; Laipple, B.; Eitschberger, H.

2005-01-01

The determination of the thermal reactor power is traditionally be done by heat balance: 1) for a boiling water reactor (BWR) at the interface of reactor control volume and heat cycle. 2) for a pressurised-water reactor (PWR) at the interface of the steam generator control volume and turbine island on the secondary side. The uncertainty of these traditional methods is not easy to determine and can be in the range of several percent. Technical and legal regulations (e.g. 10CFR50) cover an estimated error of instrumentation up to 2% by increasing the design thermal reactor power for emergency analysis to 102 % of the licensed thermal reactor power. Basically the licensee has the duty to warrant at any time operation inside the analyzed region for thermal reactor power. This is normally done by keeping the indicated reactor power at the licensed 100% value. The better way is to use a method which allows a continuous warranty evaluation. The quantification of the level of fulfilment of this warranty is only achievable by a method which: 1) is independent of single measurements accuracies. 2) results in a certified quality of single process values and for the total heat cycle analysis. 3)leads to complete results including 2-sigma deviation especially for thermal reactor power. Here this method, which is called 'process data reconciliation based on VDI 2048 guideline', is presented [1, 2]. This method allows to determine the true process parameters with a statistical probability of 95%, by considering closed material, mass- and energy balances following the Gaussian correction principle. The amount of redundant process information and complexity of the process improves the final results. This represents the most probable state of the process with minimized uncertainty according to VDI 2048. Hence, calibration and control of the thermal reactor power are possible with low effort but high accuracy and independent of single measurement accuracies. Further more, VDI 2048

New method for presenting offsite radiological monitoring data during emergency preparedness exercises

International Nuclear Information System (INIS)

Moeller, M.P.; Martin, G.F.; Hickey, E.E.; Jamison, J.D.

1986-09-01

As scenarios for exercises become more complicated and flexible to challenge emergency response personnel, improved means of presenting data must be developed. To provide maximum realism and free play during an exercise, staff at the Pacific Northwest Laboratory (PNL) have recently devised a simple method of presenting realistic radiological field monitoring information for a range of possible releases. The method uses only two pieces of paper. The first is a map of the offsite area showing the shape of the plume for the duration of the exercise. The second is a semilog graph containing curves that relate exposure rate and iodine concentration to downwind distance and time. Several techniques are used to maximize the information on the graph

EDF - 2005 Consolidated Annual Results - Analysts' Presentation. Consolidated financial statements at December 31, 2005

International Nuclear Information System (INIS)

2006-01-01

As the world's biggest electricity generator, the EDF Group covers every sector of expertise, from generation to trading and transmission grids. EDF builds on the expertise of its people, its R and D and engineering skills, its experience as a leading industry operator and the attentive support of its customers to deliver competitive solutions that successfully reconcile economic growth with climate protection. This document presents the 2005 annual results and Consolidated financial statements of the Group at 31 December 2005: Consolidated income statements, consolidated balance sheets, consolidated cash flow statements, variation in consolidated equity, notes (group accounting policies, impact of first-time application of IFRs, transition to standards IAS 32 and 39 concerning financial instruments, summary of accounting and valuation methods, public distribution concessions in France, significant events and transactions of 2005, impact of the law of august 9, 2004 on comparability, changes in the scope of consolidation, segment reporting, sales, fuel and energy purchases, other external expenses, contractual obligations and commitments entered into in the course of business, personnel expenses, other operating income and expenses, other income and expenses, financial result, income taxes, basic earnings per share and diluted earnings per share, goodwill, other intangible assets, property, plant and equipment, investments in companies accounted for under the equity method, financial assets, inventories, including work-in-process, trade receivables, other receivables, cash and cash equivalents, available-for-sale assets and liabilities, equity, provisions, special concession liabilities, current and non-current financial liabilities, derivatives, other liabilities, related parties, greenhouse gas emission quotas, environment, subsequent events, scope of consolidation

Methods of albumin estimation in clinical biochemistry: Past, present, and future.

Science.gov (United States)

Kumar, Deepak; Banerjee, Dibyajyoti

2017-06-01

Estimation of serum and urinary albumin is routinely performed in clinical biochemistry laboratories. In the past, precipitation-based methods were popular for estimation of human serum albumin (HSA). Currently, dye-binding or immunochemical methods are widely practiced. Each of these methods has its limitations. Research endeavors to overcome such limitations are on-going. The current trends in methodological aspects of albumin estimation guiding the field have not been reviewed. Therefore, it is the need of the hour to review several aspects of albumin estimation. The present review focuses on the modern trends of research from a conceptual point of view and gives an overview of recent developments to offer the readers a comprehensive understanding of the subject. Copyright © 2017 Elsevier B.V. All rights reserved.

Hydrogen storage in single-walled carbon nanotubes: methods and results

International Nuclear Information System (INIS)

Poirier, E.; Chahine, R.; Tessier, A.; Cossement, D.; Lafi, L.; Bose, T.K.

2004-01-01

We present high sensitivity gravimetric and volumetric hydrogen sorption measurement systems adapted for in situ conditioning under high temperature and high vacuum. These systems, which allow for precise measurements on small samples and thorough degassing, are used for sorption measurements on carbon nanostructures. We developed one volumetric system for the pressure range 0-1 bar, and two gravimetric systems for 0-1 bar and 0-100 bars. The use of both gravimetric and volumetric methods allows for the cross-checking of the results. The accuracy of the systems has been determined from hydrogen absorption measurements on palladium. The accuracies of the 0-1 bar volumetric and gravimetric systems are about 10 μg and 20 μg respectively. The accuracy of the 0-100 bars gravimetric system is about 20 μg. Hydrogen sorption measurements on single-walled carbon nanotubes (SWNTs) and metal-incorporated- SWNTs are presented. (author)

The numerical method of inverse Laplace transform for calculation of overvoltages in power transformers and test results

Directory of Open Access Journals (Sweden)

Mikulović Jovan Č.

2014-01-01

Full Text Available A methodology for calculation of overvoltages in transformer windings, based on a numerical method of inverse Laplace transform, is presented. Mathematical model of transformer windings is described by partial differential equations corresponding to distributed parameters electrical circuits. The procedure of calculating overvoltages is applied to windings having either isolated neutral point, or grounded neutral point, or neutral point grounded through impedance. A comparative analysis of the calculation results obtained by the proposed numerical method and by analytical method of calculation of overvoltages in transformer windings is presented. The results computed by the proposed method and measured voltage distributions, when a voltage surge is applied to a three-phase 30 kVA power transformer, are compared. [Projekat Ministartsva nauke Republike Srbije, br. TR-33037 i br. TR-33020

Discussion paper (presented during meeting)

International Nuclear Information System (INIS)

Allemand, R.

1975-01-01

A method of particle localization for gas chambers (backgammon game method) is presented. The cathode is geometrically cut in such a way that it is possible to establish a simple relation between the signal amplitude on the different parts of the cathode and the position of the nuclear event. The results obtained in the case of x-ray detectors are presented. The application of this method to the localization of neutrons is presently studied [fr

Application of NUREG-1150 methods and results to accident management

International Nuclear Information System (INIS)

Dingman, S.; Sype, T.; Camp, A.; Maloney, K.

1991-01-01

The use of NUREG-1150 and similar probabilistic risk assessments in the Nuclear Regulatory Commission (NRC) and industry risk management programs is discussed. Risk management is more comprehensive than the commonly used term accident management. Accident management includes strategies to prevent vessel breach, mitigate radionuclide releases from the reactor coolant system, and mitigate radionuclide releases to the environment. Risk management also addresses prevention of accident initiators, prevention of core damage, and implementation of effective emergency response procedures. The methods and results produced in NUREG-1150 provide a framework within which current risk management strategies can be evaluated, and future risk management programs can be developed and assessed. Examples of the use of the NUREG-1150 framework for identifying and evaluating risk management options are presented. All phases of risk management are discussed, with particular attention given to the early phases of accidents. Plans and methods for evaluating accident management strategies that have been identified in the NRC accident management program are discussed

Application of NUREG-1150 methods and results to accident management

International Nuclear Information System (INIS)

Dingman, S.; Sype, T.; Camp, A.; Maloney, K.

1990-01-01

The use of NUREG-1150 and similar Probabilistic Risk Assessments in NRC and industry risk management programs is discussed. ''Risk management'' is more comprehensive than the commonly used term ''accident management.'' Accident management includes strategies to prevent vessel breach, mitigate radionuclide releases from the reactor coolant system, and mitigate radionuclide releases to the environment. Risk management also addresses prevention of accident initiators, prevention of core damage, and implementation of effective emergency response procedures. The methods and results produced in NUREG-1150 provide a framework within which current risk management strategies can be evaluated, and future risk management programs can be developed and assessed. Examples of the use of the NUREG-1150 framework for identifying and evaluating risk management options are presented. All phases of risk management are discussed, with particular attention given to the early phases of accidents. Plans and methods for evaluating accident management strategies that have been identified in the NRC accident management program are discussed. 2 refs., 3 figs

Present status of transport code development based on Monte Carlo method

International Nuclear Information System (INIS)

Nakagawa, Masayuki

1985-01-01

The present status of development in Monte Carlo code is briefly reviewed. The main items are the followings; Application fields, Methods used in Monte Carlo code (geometry spectification, nuclear data, estimator and variance reduction technique) and unfinished works, Typical Monte Carlo codes and Merits of continuous energy Monte Carlo code. (author)

LHC experiments present new results at Quark Matter 2011 Conference

CERN Multimedia

CERN Press Office

2011-01-01

The three LHC experiments that study lead ion collisions all presented their latest results today at the annual Quark Matter conference, held this year in Annecy, France. The results are based on analysis of data collected during the last two weeks of the 2010 LHC run, when the LHC switched from protons to lead-ions. All experiments report highly subtle measurements, bringing heavy-ion physics into a new era of high precision studies.   Events recorded by the ALICE experiment from the first lead ion collisions (Nov-Dec 2010). “These results from the LHC lead ion programme are already starting bring new understanding of the primordial universe,” said CERN Director General Rolf Heuer. “The subtleties they are already seeing are very impressive.” In its infancy, just microseconds after the Big Bang, the universe consisted of a plasma of quarks and gluons (QGP), the fundamental building blocks of matter. By colliding heavy ions, physicists can turn back time an...

Searches for new physics: Les Houches recommendations for the presentation of LHC results

Energy Technology Data Exchange (ETDEWEB)

Kraml, S.; /LPSC, Grenoble; Allanach, B.C.; /Cambridge U., DAMTP; Mangano, M.; /CERN; Prosper, H.B.; /Florida State U.; Sekmen, S.; /CERN /Florida State U.; Balazs, C.; /Monash U.; Barr, A.; /Oxford U.; Bechtle, P.; /Bonn U.; Belanger, G.; /Annecy, LAPTH; Belyaev, A.; /Rutherford /Southampton U.; Benslama, K.; /Regina U.; Campanelli, M.; /University Coll. London; Cranmer, K.; /New York U., CCPP; De Roeck, A.; /CERN; Dolan, M.J.; /Durham U., IPPP; Eifert, T.; /SLAC; Ellis, J.R.; /King' s Coll. London /CERN; Felcini, M.; /Cantabria U., Santander; Fuks, B.; /Strasbourg, IPHC /Strasbourg, IReS; Guadagnoli, D.; /Orsay, LPT /Annecy, LAPTH; Gunion, J.F.; /UC, Davis /Cantabria U., Santander /SLAC /NICPB, Tallinn /Aachen, Tech. Hochsch. /Fermilab /Clermont-Ferrand U. /CERN /Clermont-Ferrand U. /Northern Illinois U. /Santa Barbara, KITP /SLAC /Dresden, Tech. U. /Gent U. /DESY

2012-04-17

We present a set of recommendations for the presentation of LHC results on searches for new physics, which are aimed at providing a more efficient flow of scientific information between the experimental collaborations and the rest of the high energy physics community, and at facilitating the interpretation of the results in a wide class of models. Implementing these recommendations would aid the full exploitation of the physics potential of the LHC.

Searches for New Physics: Les Houches Recommendations for the Presentation of LHC Results

Energy Technology Data Exchange (ETDEWEB)

Kraml, S.; et al.

2012-04-17

We present a set of recommendations for the presentation of LHC results on searches for new physics, which are aimed at providing a more efficient flow of scientific information between the experimental collaborations and the rest of the high energy physics community, and at facilitating the interpretation of the results in a wide class of models. Implementing these recommendations would aid the full exploitation of the physics potential of the LHC.

Methods uncovering usability issues in medication-related alerting functions: results from a systematic review.

Science.gov (United States)

Marcilly, Romaric; Vasseur, Francis; Ammenwerth, Elske; Beuscart-Zephir, Marie-Catherine

2014-01-01

This paper aims at listing the methods used to evaluate the usability of medication-related alerting functions and at knowing what type of usability issues those methods allow to detect. A sub-analysis of data from this systematic review has been performed. Methods applied in the included papers were collected. Then, included papers were sorted in four types of evaluation: "expert evaluation", "user- testing/simulation", "on site observation" and "impact studies". The types of usability issues (usability flaws, usage problems and negative outcomes) uncovered by those evaluations were analyzed. Results show that a large set of methods are used. The largest proportion of papers uses "on site observation" evaluation. This is the only evaluation type for which every kind of usability flaws, usage problems and outcomes are detected. It is somehow surprising that, in a usability systematic review, most of the papers included use a method that is not often presented as a usability method. Results are discussed about the opportunity to provide usability information collected after the implementation of the technology during their design process, i.e. before their implementation.

Recent results on polarizations and the present status of the Fermilab polarized beams

International Nuclear Information System (INIS)

Yokosawa, Akihiko.

1986-01-01

Experimental results are reviewed on polarization phenomena in nucleon-nucleon scattering at intermediate energies. The present status of S = 0 dibaryon resonances is presented. The status of the Fermilab polarized beam program is presented, including the construction of polarized beam, two polarimeters being installed in the experimental hall, and the experimental program

Presentations from the Aeroelastic Workshop - latest results from AeroOpt

Energy Technology Data Exchange (ETDEWEB)

Hartvig Hansen, M. (ed.)

2011-10-15

This report contains the slides of the presentations at the Aeroelastic Workshop held at Risoe-DTU for the wind energy industry in Denmark on October 27, 2011. The scientific part of the agenda at this workshop was 1) Detailed and reduced models of dynamic mooring system (Anders M. Hansen). 2) Bend-twist coupling investigation in HAWC2 (Taeseong Kim). 3) Q3UIC - A new aerodynamic airfoil tool including rotational effects (Nestor R. Garcia). 4) Influence of up-scaling on loads, control and aerodynamic modeling (Helge Aa. Madsen). 5) Aerodynamic damping of lateral tower vibrations (Bjarne S. Kallesoee). 6) Open- and closed-loop aeroservoelastic analysis with HAWCStab2 (Morten H. Hansen). 7) Design and test of a thick, flatback, high-lift multielement airfoil (Frederik Zahle). The presented results are mainly obtained in the EUDP project ''Aeroelastic Optimization of MW Wind Turbines (AeroOpt)''. (Author)

A New Method Presentation for Fault Location in Power Transformers

OpenAIRE

Hossein Mohammadpour; Rahman Dashti

2011-01-01

Power transformers are among the most important and expensive equipments in the electric power systems. Consequently the transformer protection is an essential part of the system protection. This paper presents a new method for locating transformer winding faults such as turn-to-turn, turn-to-core, turn-totransformer body, turn-to-earth, and high voltage winding to low voltage winding. In this study the current and voltage signals of input and output terminals of the tran...

Searches for new physics: Les Houches recommendations for the presentation of LHC results

International Nuclear Information System (INIS)

Kraml, S.; Allanach, B.C.; Mangano, M.; Roeck, A. de; Prosper, H.B.; Sekmen, S.; Balazs, C.; Barr, A.; Bechtle, P.; Belanger, G.; Belyaev, A.; Benslama, K.; Campanelli, M.; Cranmer, K.; Dolan, M.J.; Eifert, T.; Hewett, J.; Ismail, A.; Rizzo, T.; Ellis, J.R.; Felcini, M.; Heinemeyer, S.; Fuks, B.; Guadagnoli, D.; Gunion, J.F.; Kadastik, M.; Kraemer, M.; Lykken, J.; Mahmoudi, F.; Martin, S.P.; Robens, T.; Tytgat, M.; Weiler, A.

2012-01-01

We present a set of recommendations for the presentation of LHC results on searches for new physics, which are aimed at providing a more efficient flow of scientific information between the experimental collaborations and the rest of the high energy physics community, and at facilitating the interpretation of the results in a wide class of models. Implementing these recommendations would aid the full exploitation of the physics potential of the LHC. (orig.)

Searches for New Physics: Les Houches Recommendations for the Presentation of LHC Results

International Nuclear Information System (INIS)

Kraml, S.; Allanach, B.C.; Mangano, M.; Prosper, H.B.; Sekmen, S.; Balazs, C.; Barr, A.; Bechtle, P.; Belanger, G.; Belyaev, A.; Kenslama, K.; Campanelli, M.; Cranmer, K.; De Roeck, A.; Dolan, M.J.; Ellis, J.R.; Felcini, M.; Fuks, B.; Guadagnoli, D.; Gunion, J.F.; Heinemeyer, S.; Hewett, J.; Ismail, A.; Kadastik, M.; Kraemer, M.; Lykken, J.; Mahmoudi, F.; Martin, S.P.; Rizzo, T.; Robens, T.; Tytgat, M.; Weiler, A.

2012-01-01

We present a set of recommendations for the presentation of LHC results on searches for new physics, which are aimed at providing a more efficient flow of scientific information between the experimental collaborations and the rest of the high energy physics community, and at facilitating the interpretation of the results in a wide class of models. Implementing these recommendations would aid the full exploitation of the physics potential of the LHC. (authors)

Enhanced Cognitive Walkthrough: Development of the Cognitive Walkthrough Method to Better Predict, Identify, and Present Usability Problems

Directory of Open Access Journals (Sweden)

Lars-Ola Bligård

2013-01-01

Full Text Available To avoid use errors when handling medical equipment, it is important to develop products with a high degree of usability. This can be achieved by performing usability evaluations in the product development process to detect and mitigate potential usability problems. A commonly used method is cognitive walkthrough (CW, but this method shows three weaknesses: poor high-level perspective, insufficient categorisation of detected usability problems, and difficulties in overviewing the analytical results. This paper presents a further development of CW with the aim of overcoming its weaknesses. The new method is called enhanced cognitive walkthrough (ECW. ECW is a proactive analytical method for analysis of potential usability problems. The ECW method has been employed to evaluate user interface designs of medical equipment such as home-care ventilators, infusion pumps, dialysis machines, and insulin pumps. The method has proved capable of identifying several potential use problems in designs.

A Pragmatic Smoothing Method for Improving the Quality of the Results in Atomic Spectroscopy

Science.gov (United States)

Bennun, Leonardo

2017-07-01

A new smoothing method for the improvement on the identification and quantification of spectral functions based on the previous knowledge of the signals that are expected to be quantified, is presented. These signals are used as weighted coefficients in the smoothing algorithm. This smoothing method was conceived to be applied in atomic and nuclear spectroscopies preferably to these techniques where net counts are proportional to acquisition time, such as particle induced X-ray emission (PIXE) and other X-ray fluorescence spectroscopic methods, etc. This algorithm, when properly applied, does not distort the form nor the intensity of the signal, so it is well suited for all kind of spectroscopic techniques. This method is extremely effective at reducing high-frequency noise in the signal much more efficient than a single rectangular smooth of the same width. As all of smoothing techniques, the proposed method improves the precision of the results, but in this case we found also a systematic improvement on the accuracy of the results. We still have to evaluate the improvement on the quality of the results when this method is applied over real experimental results. We expect better characterization of the net area quantification of the peaks, and smaller Detection and Quantification Limits. We have applied this method to signals that obey Poisson statistics, but with the same ideas and criteria, it could be applied to time series. In a general case, when this algorithm is applied over experimental results, also it would be required that the sought characteristic functions, required for this weighted smoothing method, should be obtained from a system with strong stability. If the sought signals are not perfectly clean, this method should be carefully applied

Methods and optical fibers that decrease pulse degradation resulting from random chromatic dispersion

Science.gov (United States)

Chertkov, Michael; Gabitov, Ildar

2004-03-02

The present invention provides methods and optical fibers for periodically pinning an actual (random) accumulated chromatic dispersion of an optical fiber to a predicted accumulated dispersion of the fiber through relatively simple modifications of fiber-optic manufacturing methods or retrofitting of existing fibers. If the pinning occurs with sufficient frequency (at a distance less than or are equal to a correlation scale), pulse degradation resulting from random chromatic dispersion is minimized. Alternatively, pinning may occur quasi-periodically, i.e., the pinning distance is distributed between approximately zero and approximately two to three times the correlation scale.

Qualitative and quantitative methods for human factor analysis and assessment in NPP. Investigations and results

International Nuclear Information System (INIS)

Hristova, R.; Kalchev, B.; Atanasov, D.

2005-01-01

We consider here two basic groups of methods for analysis and assessment of the human factor in the NPP area and give some results from performed analyses as well. The human factor is the human interaction with the design equipment, with the working environment and takes into account the human capabilities and limits. In the frame of the qualitative methods for analysis of the human factor are considered concepts and structural methods for classifying of the information, connected with the human factor. Emphasize is given to the HPES method for human factor analysis in NPP. Methods for quantitative assessment of the human reliability are considered. These methods allow assigning of probabilities to the elements of the already structured information about human performance. This part includes overview of classical methods for human reliability assessment (HRA, THERP), and methods taking into account specific information about human capabilities and limits and about the man-machine interface (CHR, HEART, ATHEANA). Quantitative and qualitative results concerning human factor influence in the initiating events occurrences in the Kozloduy NPP are presented. (authors)

PALEOEARTHQUAKES IN THE PRIBAIKALIE: METHODS AND RESULTS OF DATING

Directory of Open Access Journals (Sweden)

Oleg P. Smekalin

2010-01-01

Full Text Available In the Pribaikalie and adjacent territories, seismogeological studies have been underway for almost a half of the century and resulted in discovery of more than 70 dislocations of seismic or presumably seismic origin. With commencement of paleoseismic studies, dating of paleo-earthquakes was focused on as an indicator useful for long-term prediction of strong earthquakes. V.P. Solonenko [Solonenko, 1977] distinguished five methods for dating paleoseismogenic deformations, i.e. geological, engineering geological, historico-archeological, dendrochronological and radiocarbon methods. However, ages of the majority of seismic deformations, which were subject to studies at the initial stage of development of seismogeology in Siberia, were defined by methods of relative or correlation age determination.Since the 1980s, studies of seismogenic deformation in the Pribaikalie have been widely conducted with trenching. Mass sampling, followed with radiocarbon analyses and definition of absolute ages of paleo-earthquakes, provided new data on seismic regimes of the territory and rates of and recent displacements along active faults, and enhanced validity of methods of relative dating, in particular morphometry. Capacities of the morphometry method has significantly increased with introduction of laser techniques in surveys and digital processing of 3D relief models.Comprehensive seismogeological studies conducted in the Pribaikalie revealed 43 paleo-events within 16 seismogenic structures. Absolute ages of 18 paleo-events were defined by the radiocarbon age determination method. Judging by their ages, a number of dislocations were related with historical earthquakes which occurred in the 18th and 19th centuries, yet any reliable data on epicenters of such events are not available. The absolute and relative dating methods allowed us to identify sections in some paleoseismogenic structures by differences in ages of activation and thus provided new data for

Tensile strength of concrete under static and intermediate strain rates: Correlated results from different testing methods

International Nuclear Information System (INIS)

Wu Shengxing; Chen Xudong; Zhou Jikai

2012-01-01

Highlights: ► Tensile strength of concrete increases with increase in strain rate. ► Strain rate sensitivity of tensile strength of concrete depends on test method. ► High stressed volume method can correlate results from various test methods. - Abstract: This paper presents a comparative experiment and analysis of three different methods (direct tension, splitting tension and four-point loading flexural tests) for determination of the tensile strength of concrete under low and intermediate strain rates. In addition, the objective of this investigation is to analyze the suitability of the high stressed volume approach and Weibull effective volume method to the correlation of the results of different tensile tests of concrete. The test results show that the strain rate sensitivity of tensile strength depends on the type of test, splitting tensile strength of concrete is more sensitive to an increase in the strain rate than flexural and direct tensile strength. The high stressed volume method could be used to obtain a tensile strength value of concrete, free from the influence of the characteristics of tests and specimens. However, the Weibull effective volume method is an inadequate method for describing failure of concrete specimens determined by different testing methods.

A revised method of presenting wavenumber-frequency power spectrum diagrams that reveals the asymmetric nature of tropical large-scale waves

Energy Technology Data Exchange (ETDEWEB)

Chao, Winston C. [NASA/Goddard Space Flight Center, Global Modeling and Assimilation Office, Mail Code 610.1, Greenbelt, MD (United States); Yang, Bo; Fu, Xiouhua [University of Hawaii at Manoa, School of Ocean and Earth Science and Technology, International Pacific Research Center, Honolulu, HI (United States)

2009-11-15

The popular method of presenting wavenumber-frequency power spectrum diagrams for studying tropical large-scale waves in the literature is shown to give an incomplete presentation of these waves. The so-called ''convectively coupled Kelvin (mixed Rossby-gravity) waves'' are presented as existing only in the symmetric (anti-symmetric) component of the diagrams. This is obviously not consistent with the published composite/regression studies of ''convectively coupled Kelvin waves,'' which illustrate the asymmetric nature of these waves. The cause of this inconsistency is revealed in this note and a revised method of presenting the power spectrum diagrams is proposed. When this revised method is used, ''convectively coupled Kelvin waves'' do show anti-symmetric components, and ''convectively coupled mixed Rossby-gravity waves (also known as Yanai waves)'' do show a hint of symmetric components. These results bolster a published proposal that these waves should be called ''chimeric Kelvin waves,'' ''chimeric mixed Rossby-gravity waves,'' etc. This revised method of presenting power spectrum diagrams offers an additional means of comparing the GCM output with observations by calling attention to the capability of GCMs to correctly simulate the asymmetric characteristics of equatorial waves. (orig.)

Analysis of risk of nonconformities and applied quality inspection methods in the process of aluminium profiles coating based on FMEA results

OpenAIRE

Krzysztof Knop

2017-01-01

The article presents the results of risk analysis associated with nonconformities of aluminium profiles in the process of coating and quality inspection methods used to their detection. Analysis of risk was done based on results of FMEA method. Evaluated quality inspection methods were distinguished based on the term of inspection in the ISO 9000:2005 norm. Manufacturing process of aluminium profile in micro-technological approach was presented. Triple quantification of nonconformities risk b...

Interpretation and presentation of results. Chickens will come home to roost.

Science.gov (United States)

Beattie, A; Donovan, B; Mant, A; Bridges-Webb, C

1984-06-01

Collecting information is an obsessional activity which can become an end in itself. Interpreting and presenting results in a way that others can learn from them requires reflection, selectivity and ability to accept criticism. In selecting the journal to which the article will be submitted, consider which has the most appropriate readership and ensure the article conforms to the requirements and style of that journal.

The DIVA programme: General presentation and first results

International Nuclear Information System (INIS)

Dumaz, P.; Duc, B.

2000-01-01

The French 'Commissariat a I'Energie Atomique' (CEA/DRN, Nuclear Reactor Division) is carrying out a new programme devoted to the thermal-hydraulics of steam injectors. This programme was called DIVA. Both experimental and theoretical works are planned. Motivations, objectives, test facility and test section dimensioning of this new programme are presented. A first test series was just performed. The validation of the test section dimensioning and experimental procedures was obtained. These first experimental data are presented and preliminary analyses are given. (author)

The estimation of the measurement results with using statistical methods

International Nuclear Information System (INIS)

Ukrmetrteststandard, 4, Metrologichna Str., 03680, Kyiv (Ukraine))" data-affiliation=" (State Enterprise Ukrmetrteststandard, 4, Metrologichna Str., 03680, Kyiv (Ukraine))" >Velychko, O; UkrNDIspirtbioprod, 3, Babushkina Lane, 03190, Kyiv (Ukraine))" data-affiliation=" (State Scientific Institution UkrNDIspirtbioprod, 3, Babushkina Lane, 03190, Kyiv (Ukraine))" >Gordiyenko, T

2015-01-01

The row of international standards and guides describe various statistical methods that apply for a management, control and improvement of processes with the purpose of realization of analysis of the technical measurement results. The analysis of international standards and guides on statistical methods estimation of the measurement results recommendations for those applications in laboratories is described. For realization of analysis of standards and guides the cause-and-effect Ishikawa diagrams concerting to application of statistical methods for estimation of the measurement results are constructed

The estimation of the measurement results with using statistical methods

Science.gov (United States)

Velychko, O.; Gordiyenko, T.

2015-02-01

The row of international standards and guides describe various statistical methods that apply for a management, control and improvement of processes with the purpose of realization of analysis of the technical measurement results. The analysis of international standards and guides on statistical methods estimation of the measurement results recommendations for those applications in laboratories is described. For realization of analysis of standards and guides the cause-and-effect Ishikawa diagrams concerting to application of statistical methods for estimation of the measurement results are constructed.

Present and future of the hybrid imaging method SPECT/CT

International Nuclear Information System (INIS)

Kostadinova, I.

2013-01-01

Full text: Introduction: Based on the data in the literature and on our 4 year clinical experience applied for the first time in our country hybrid imaging - single photon emission tomography combined with computed tomography (SPECT / CT) it is clear that to obtain comprehensive information about the function and structure of the studied organ; the time for the diagnosis and thus the start of adequate treatment become shorter. The resulting scintigraphic image is with better quality due to CT correction of ‘diffusion’ gamma radiation, which leads to greater diagnostic accuracy. What you will learn: complex imaging method is used mainly in the field of endocrinology, cardiology, oncology, orthopedics, pulmology, neurology, and neurosurgery. It can be prove a given disease by visualization and localization of the organ lesions and determine the stage of the tumor process, to plan the type of subsequent treatment, to follow the effects of the therapy, and to predict the effect of an interventional or miniinvasive surgical procedure. Discussion: The result of the application of the hybrid imaging method is a change in the interpretation of more than half of the studied patients and in the treatment in more than a quarter of them. Conclusion: The clinical indications for SPECT/CT, and evidence of increased diagnostic accuracy compared with self- administered scintigraphic or CT methods are continuous expanded

Nuclear analytical methods: Past, present and future

International Nuclear Information System (INIS)

Becker, D.A.

1996-01-01

The development of nuclear analytical methods as an analytical tool began in 1936 with the publication of the first paper on neutron activation analysis (NAA). This year, 1996, marks the 60th anniversary of that event. This paper attempts to look back at the nuclear analytical methods of the past, to look around and to see where the technology is right now, and finally, to look ahead to try and see where nuclear methods as an analytical technique (or as a group of analytical techniques) will be going in the future. The general areas which the author focuses on are: neutron activation analysis; prompt gamma neutron activation analysis (PGNAA); photon activation analysis (PAA); charged-particle activation analysis (CPAA)

Project Oriented Immersion Learning: Method and Results

DEFF Research Database (Denmark)

Icaza, José I.; Heredia, Yolanda; Borch, Ole M.

2005-01-01

A pedagogical approach called “project oriented immersion learning” is presented and tested on a graduate online course. The approach combines the Project Oriented Learning method with immersion learning in a virtual enterprise. Students assumed the role of authors hired by a fictitious publishing...... house that develops digital products including e-books, tutorials, web sites and so on. The students defined the problem that their product was to solve; choose the type of product and the content; and built the product following a strict project methodology. A wiki server was used as a platform to hold...

Multiband discrete ordinates method: formalism and results; Methode multibande aux ordonnees discretes: formalisme et resultats

Energy Technology Data Exchange (ETDEWEB)

Luneville, L

1998-06-01

The multigroup discrete ordinates method is a classical way to solve transport equation (Boltzmann) for neutral particles. Self-shielding effects are not correctly treated due to large variations of cross sections in a group (in the resonance range). To treat the resonance domain, the multiband method is introduced. The main idea is to divide the cross section domain into bands. We obtain the multiband parameters using the moment method; the code CALENDF provides probability tables for these parameters. We present our implementation in an existing discrete ordinates code: SN1D. We study deep penetration benchmarks and show the improvement of the method in the treatment of self-shielding effects. (author) 15 refs.

New method for presenting off-site radiological monitoring data during emergency preparedness exercises

International Nuclear Information System (INIS)

Moeller, M.P.; Martin, G.F.; Hickey, E.E.; Jamison, J.D.

1987-01-01

As scenarios for exercises become more complicated and flexible to challenge emergency response personnel, improved means of presenting data must be developed to meet this need. To provide maximum realism and free play during an exercise, staff at the Pacific Northwest Laboratory (PNL) have recently devised a simple method of presenting realistic radiological field monitoring information for a range of possible releases. The method utilizes only two pieces of paper. The first is a map of the offsite area showing the shape of the plume for the duration of the exercise. The second is a semi-log graph containing curves relating exposure rate and iodine concentration to downwind distance and time. Several techniques are used to maximize the information on the graph

Improved Method of Detection Falsification Results the Digital Image in Conditions of Attacks

Directory of Open Access Journals (Sweden)

Kobozeva A.A.

2016-08-01

Full Text Available The modern level of information technologies development has led to unheard ease embodiments hitherto unauthorized modifications of digital content. At the moment, very important question is the effective expert examination of authenticity of digital images, video, audio, development of the methods for identification and localization of violations of their integrity using these contents for purposes other than entertainment. Present paper deals with the improvement of the detection method of the cloning results in digital images - one of the most frequently used in the software tools falsification realized in all modern graphics editors. The method is intended for clone detection areas and pre-image in terms of additional disturbing influences in the image after the cloning operation for "masking" of the results, which complicates the search process. The improvement is aimed at reducing the number of "false alarms", when the area of the clone / pre-image detected in the original image or the localization of the identified areas do not correspond to the real clone and pre-image. The proposed improvement, based on analysis of different sizes per-pixel image blocks with the least difference from each other, has made it possible efficient functioning of the method, regardless of the specificity of the analyzed digital image.

Presentation of a method for the sequential analysis of incidents - NPP safety

Energy Technology Data Exchange (ETDEWEB)

Delage, M; Giroux, C; Quentin, P

1989-04-01

This paper presents a method which is designed to assist in the analysis of safety and based on the graphic representation of the occurrence of incidents significant for safety in 900-MWe PWR units. The graphs obtained are linked together to produce a general tree of events. With this tool, and on the basis of operating experience, it is then possible to imagine complex incident scenarios, to evaluate the potential consequences of a particular incident, or to seed out the causes which could lead to a given event. Interactions between systems or common mode faults can also be evidenced with this method.

The failure combination method: presentation, application to a simple collection of systems

International Nuclear Information System (INIS)

Llory, M.; Villemeur, A.

1981-11-01

The main advantages of this particular method for analyzing the reliability and safety of systems, the method of failure combinations, are presented. This is an inductive method of analysis; it makes it possible to pursue the Failure Modes and Effect Analysis (FMEA) until overall failures are obtained. In this manner, through an inductive approach all the combinations of failure modes leading to abnormal functioning of systems are obtained. It also makes it possible to carry out the overall study of complex systems in interaction and the systematic inventory of abnormal functioning of these systems, as from the failure modes of the components and their combinations. It can be used as from the design stages of systems and is an excellent dialogue tool between the various specialists concerned in problems of safety, operation and reliability [fr

High-performance liquid chromatography method for the determination of hydrogen peroxide present or released in teeth bleaching kits and hair cosmetic products.

Science.gov (United States)

Gimeno, Pascal; Bousquet, Claudine; Lassu, Nelly; Maggio, Annie-Françoise; Civade, Corinne; Brenier, Charlotte; Lempereur, Laurent

2015-03-25

This manuscript presents an HPLC/UV method for the determination of hydrogen peroxide present or released in teeth bleaching products and hair products. The method is based on an oxidation of triphenylphosphine into triphenylphosphine oxide by hydrogen peroxide. Triphenylphosphine oxide formed is quantified by HPLC/UV. Validation data were obtained using the ISO 12787 standard approach, particularly adapted when it is not possible to make reconstituted sample matrices. For comparative purpose, hydrogen peroxide was also determined using ceric sulfate titrimetry for both types of products. For hair products, a cross validation of both ceric titrimetric method and HPLC/UV method using the cosmetic 82/434/EEC directive (official iodometric titration method) was performed. Results obtained for 6 commercialized teeth whitening products and 5 hair products point out similar hydrogen peroxide contain using either the HPLC/UV method or ceric sulfate titrimetric method. For hair products, results were similar to the hydrogen peroxide content using the cosmetic 82/434/EEC directive method and for the HPLC/UV method, mean recoveries obtained on spiked samples, using the ISO 12787 standard, ranges from 100% to 110% with a RSDhydrogen peroxide contents higher than the regulated limit. Copyright © 2015 Elsevier B.V. All rights reserved.

The effects of presentation methods and semantic information on multi-ethnicity face recognition

Directory of Open Access Journals (Sweden)

Kaarel Rundu

2012-01-01

Full Text Available Studies have shown that own-race faces are more accurately recognised than other-race faces. The present study examined the effects of own- and other-race face recognition when different ethnicity targets are presented to the participants together. Also the effect of semantic information on the recognition of different race faces was examined. The participants (N = 234 were presented with photos of own-race and other-race faces. For some participants the faces were presented with stereotypical names and for some not. As hypothesized, own-race faces were better recognised in target-present lineup and more correctly rejected in target-absent lineup than other-race faces. Concerning presentation method, both own-race and other-race faces were more correctly identified in target-present simultaneous than in target-present sequential lineups. No effects of stereotypical names on face recognition were found. The findings suggest that identifying multi-ethnicity perpetrators is a problematic and difficult task.

Vehicle Speed Determination in Case of Road Accident by Software Method and Comparing of Results with the Mathematical Model

OpenAIRE

Hoxha Gezim; Shala Ahmet; Likaj Rame

2017-01-01

The paper addresses the problem to vehicle speed calculation at road accidents. To determine the speed are used the PC Crash software and Virtual Crash. With both methods are analysed concrete cases of road accidents. Calculation methods and comparing results are present for analyse. These methods consider several factors such are: the front part of the vehicle, the technical feature of the vehicle, car angle, remote relocation after the crash, road conditions etc. Expected results with PC Cr...

Method and apparatus for simultaneously measuring a plurality of spectral wavelengths present in electromagnetic radiation

Science.gov (United States)

Buican, Tudor N.; Martin, John C.

1990-01-01

An apparatus and method simultaneously measures a plurality of spectral wavelengths present in electromagnetic radiation. A modulatable birefringent optical element is employed to divide a polarized light beam into two components, thereby producing a phase difference in two resulting light beams such that the two beams can be made to interfere with one another when recombined, the interference pattern providing the wavelength information required for the analysis of the incident light. The interferometer thus created performs in a similar manner to a Michelson interferometer, but with no moving parts, and with a resolution dependent on the degree of phase shift introduced by the modulator.

Vehicle Speed Determination in Case of Road Accident by Software Method and Comparing of Results with the Mathematical Model

Directory of Open Access Journals (Sweden)

Hoxha Gezim

2017-11-01

Full Text Available The paper addresses the problem to vehicle speed calculation at road accidents. To determine the speed are used the PC Crash software and Virtual Crash. With both methods are analysed concrete cases of road accidents. Calculation methods and comparing results are present for analyse. These methods consider several factors such are: the front part of the vehicle, the technical feature of the vehicle, car angle, remote relocation after the crash, road conditions etc. Expected results with PC Crash software and Virtual Crash are shown in tabular graphics and compared in mathematical methods.

Steady-state transport equation resolution by particle methods, and numerical results

International Nuclear Information System (INIS)

Mercier, B.

1985-10-01

A method to solve steady-state transport equation has been given. Principles of the method are given. The method is studied in two different cases; estimations given by the theory are compared to numerical results. Results got in 1-D (spherical geometry) and in 2-D (axisymmetric geometry) are given [fr

Presentation of RTE results 2003; Presentation des resultats 2003 de RTE

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

For RTE, the financial year 2003 was marked by a number of achievements: our financial performances registered a clear improvement, above objectives, with turnover growing strongly; net income reached levels almost three times higher than those recorded in 2002; the economic rate of return rose to 7.1%; and debt was reduced by 470 Meuros. These results are explained by the substantial improvement in productivity, which has risen by 5% per year on average over the last three years.

Integrating Quantitative and Qualitative Results in Health Science Mixed Methods Research Through Joint Displays

Science.gov (United States)

Guetterman, Timothy C.; Fetters, Michael D.; Creswell, John W.

2015-01-01

PURPOSE Mixed methods research is becoming an important methodology to investigate complex health-related topics, yet the meaningful integration of qualitative and quantitative data remains elusive and needs further development. A promising innovation to facilitate integration is the use of visual joint displays that bring data together visually to draw out new insights. The purpose of this study was to identify exemplar joint displays by analyzing the various types of joint displays being used in published articles. METHODS We searched for empirical articles that included joint displays in 3 journals that publish state-of-the-art mixed methods research. We analyzed each of 19 identified joint displays to extract the type of display, mixed methods design, purpose, rationale, qualitative and quantitative data sources, integration approaches, and analytic strategies. Our analysis focused on what each display communicated and its representation of mixed methods analysis. RESULTS The most prevalent types of joint displays were statistics-by-themes and side-by-side comparisons. Innovative joint displays connected findings to theoretical frameworks or recommendations. Researchers used joint displays for convergent, explanatory sequential, exploratory sequential, and intervention designs. We identified exemplars for each of these designs by analyzing the inferences gained through using the joint display. Exemplars represented mixed methods integration, presented integrated results, and yielded new insights. CONCLUSIONS Joint displays appear to provide a structure to discuss the integrated analysis and assist both researchers and readers in understanding how mixed methods provides new insights. We encourage researchers to use joint displays to integrate and represent mixed methods analysis and discuss their value. PMID:26553895

Analysis of risk of nonconformities and applied quality inspection methods in the process of aluminium profiles coating based on FMEA results

Directory of Open Access Journals (Sweden)

Krzysztof Knop

2017-10-01

Full Text Available The article presents the results of risk analysis associated with nonconformities of aluminium profiles in the process of coating and quality inspection methods used to their detection. Analysis of risk was done based on results of FMEA method. Evaluated quality inspection methods were distinguished based on the term of inspection in the ISO 9000:2005 norm. Manufacturing process of aluminium profile in micro-technological approach was presented. Triple quantification of nonconformities risk based on the FMEA method by using three different approaches was conducted. Analysis of nonconformities risks associated with the use of specific quality inspection methods was done. In the last part the analysis of causes of critical nonconformities, proposals for improvement actions reducing the risk of the critical nonconformities and applied critical quality inspection method were showed.

Esophageal Replacement in Children: Presentation of 18 Cases and Results of Their Surgical Procedure

Directory of Open Access Journals (Sweden)

S. Delshad

2007-11-01

Full Text Available Background:Esophageal replacement is indicated in certain circumstances including long gap esophageal atresia,severe strictures due to gastro-esophageal reflux (GER and caustic burns. We analyzed our results of 18 patients who underwent esophageal replacement in our university hospital. Methods:We reviewed esophageal replacements carried out in our department between June 1996 and August 2004.We report 18 patients(4 girls and 14 boys with ages ranging from 3.5 until 30 months.Fifteen patients had long gap atresia,two had strictures due to GER,and one case had caustic burn. Esophageal replacement was performed through an abdominal midline incision by one of three methods, namely: colon transposition in 15, gastric replacement in 2, and gastric tube in 1 case. Results: Leakage and stricture were the most common complications of esophageal replacement.Most deaths were due to aspiration pneumonia and congenital cardiac disease.Conclusion:Esophageal replacement has limited indications.It allows a good functional result,with adequate oral feeding and normal growth.

Presentation of laboratory test results in patient portals: influence of interface design on risk interpretation and visual search behaviour.

Science.gov (United States)

Fraccaro, Paolo; Vigo, Markel; Balatsoukas, Panagiotis; van der Veer, Sabine N; Hassan, Lamiece; Williams, Richard; Wood, Grahame; Sinha, Smeeta; Buchan, Iain; Peek, Niels

2018-02-12

Patient portals are considered valuable instruments for self-management of long term conditions, however, there are concerns over how patients might interpret and act on the clinical information they access. We hypothesized that visual cues improve patients' abilities to correctly interpret laboratory test results presented through patient portals. We also assessed, by applying eye-tracking methods, the relationship between risk interpretation and visual search behaviour. We conducted a controlled study with 20 kidney transplant patients. Participants viewed three different graphical presentations in each of low, medium, and high risk clinical scenarios composed of results for 28 laboratory tests. After viewing each clinical scenario, patients were asked how they would have acted in real life if the results were their own, as a proxy of their risk interpretation. They could choose between: 1) Calling their doctor immediately (high interpreted risk); 2) Trying to arrange an appointment within the next 4 weeks (medium interpreted risk); 3) Waiting for the next appointment in 3 months (low interpreted risk). For each presentation, we assessed accuracy of patients' risk interpretation, and employed eye tracking to assess and compare visual search behaviour. Misinterpretation of risk was common, with 65% of participants underestimating the need for action across all presentations at least once. Participants found it particularly difficult to interpret medium risk clinical scenarios. Participants who consistently understood when action was needed showed a higher visual search efficiency, suggesting a better strategy to cope with information overload that helped them to focus on the laboratory tests most relevant to their condition. This study confirms patients' difficulties in interpreting laboratories test results, with many patients underestimating the need for action, even when abnormal values were highlighted or grouped together. Our findings raise patient safety

Raw material consumption of the European Union--concept, calculation method, and results.

Science.gov (United States)

Schoer, Karl; Weinzettel, Jan; Kovanda, Jan; Giegrich, Jürgen; Lauwigi, Christoph

2012-08-21

This article presents the concept, calculation method, and first results of the "Raw Material Consumption" (RMC) economy-wide material flow indicator for the European Union (EU). The RMC measures the final domestic consumption of products in terms of raw material equivalents (RME), i.e. raw materials used in the complete production chain of consumed products. We employed the hybrid input-output life cycle assessment method to calculate RMC. We first developed a highly disaggregated environmentally extended mixed unit input output table and then applied life cycle inventory data for imported products without appropriate representation of production within the domestic economy. Lastly, we treated capital formation as intermediate consumption. Our results show that services, often considered as a solution for dematerialization, account for a significant part of EU raw material consumption, which emphasizes the need to focus on the full production chains and dematerialization of services. Comparison of the EU's RMC with its domestic extraction shows that the EU is nearly self-sufficient in biomass and nonmetallic minerals but extremely dependent on direct and indirect imports of fossil energy carriers and metal ores. This implies an export of environmental burden related to extraction and primary processing of these materials to the rest of the world. Our results demonstrate that internalizing capital formation has significant influence on the calculated RMC.

Methods of Helminthiasis Diagnosis at the Present Stage

Directory of Open Access Journals (Sweden)

I.B. Yershova

2014-04-01

Full Text Available The article describes the methods of diagnosis of helminth infestations: microscopic, immunoenzyme analysis, serology, polymerase chain reaction, bioresonance diagnostics, haemoscanning, as well as instrumental methods (ultrasound and X-ray examination, computed tomography and laboratory analysis of indirect value (complete blood count, liver function tests, fecal dysbiosis. Advantages of methods, as well as disadvantages, the reliability of the findings are described. Questionnaire for patients are offered to determine the risk of helminth infestation.

The Method for Assessing and Forecasting Value of Knowledge in SMEs – Research Results

Directory of Open Access Journals (Sweden)

Justyna Patalas-Maliszewska

2010-10-01

Full Text Available Decisions by SMEs regarding knowledge development are made at a strategic level (Haas-Edersheim, 2007. Related to knowledge management are approaches to "measure" knowledge, where literature distinguishes between qualitative and quantitative methods of valuating intellectual capital. Although there is a quite range of such methods to build an intellectual capital reporting system, none of them is really widely recognized. This work presents a method enabling assessing the effectiveness of investing in human resources, taking into consideration existing methods. The method presented is focusing on SMEs (taking into consideration their importance for, especially, regional development. It consists of four parts: an SME reference model, an indicator matrix to assess investments into knowledge, innovation indicators, and the GMDH algorithm for decision making. The method presented is exemplified by a case study including 10 companies.

A result-driven minimum blocking method for PageRank parallel computing

Science.gov (United States)

Tao, Wan; Liu, Tao; Yu, Wei; Huang, Gan

2017-01-01

Matrix blocking is a common method for improving computational efficiency of PageRank, but the blocking rules are hard to be determined, and the following calculation is complicated. In tackling these problems, we propose a minimum blocking method driven by result needs to accomplish a parallel implementation of PageRank algorithm. The minimum blocking just stores the element which is necessary for the result matrix. In return, the following calculation becomes simple and the consumption of the I/O transmission is cut down. We do experiments on several matrixes of different data size and different sparsity degree. The results show that the proposed method has better computational efficiency than traditional blocking methods.

Daily radiotoxicological supervision of personnel at the Pierrelatte industrial complex. Methods and results

International Nuclear Information System (INIS)

Chalabreysse, Jacques.

1978-05-01

A 13 year experience gained from daily radiotoxicological supervision of personnel at the PIERRELATTE industrial complex is presented. This study is divided into two parts: part one is theoretical: bibliographical synthesis of all scattered documents and publications; a homogeneous survey of all literature on the subject is thus available. Part two reviews the experience gained in professional surroundings: laboratory measurements and analyses (development of methods and daily applications); mathematical formulae to answer the first questions which arise before an individual liable to be contaminated; results obtained at PIERRELATTE [fr

[Do different interpretative methods used for evaluation of checkerboard synergy test affect the results?].

Science.gov (United States)

Ozseven, Ayşe Gül; Sesli Çetin, Emel; Ozseven, Levent

2012-07-01

In recent years, owing to the presence of multi-drug resistant nosocomial bacteria, combination therapies are more frequently applied. Thus there is more need to investigate the in vitro activity of drug combinations against multi-drug resistant bacteria. Checkerboard synergy testing is among the most widely used standard technique to determine the activity of antibiotic combinations. It is based on microdilution susceptibility testing of antibiotic combinations. Although this test has a standardised procedure, there are many different methods for interpreting the results. In many previous studies carried out with multi-drug resistant bacteria, different rates of synergy have been reported with various antibiotic combinations using checkerboard technique. These differences might be attributed to the different features of the strains. However, different synergy rates detected by checkerboard method have also been reported in other studies using the same drug combinations and same types of bacteria. It was thought that these differences in synergy rates might be due to the different methods of interpretation of synergy test results. In recent years, multi-drug resistant Acinetobacter baumannii has been the most commonly encountered nosocomial pathogen especially in intensive-care units. For this reason, multidrug resistant A.baumannii has been the subject of a considerable amount of research about antimicrobial combinations. In the present study, the in vitro activities of frequently preferred combinations in A.baumannii infections like imipenem plus ampicillin/sulbactam, and meropenem plus ampicillin/sulbactam were tested by checkerboard synergy method against 34 multi-drug resistant A.baumannii isolates. Minimum inhibitory concentration (MIC) values for imipenem, meropenem and ampicillin/sulbactam were determined by the broth microdilution method. Subsequently the activity of two different combinations were tested in the dilution range of 4 x MIC and 0.03 x MIC in

THE RESULTS OF THE ANALYSIS OF THE STUDENTS’ BODY COMPOSITION BY BIOIMPEDANCE METHOD

Directory of Open Access Journals (Sweden)

Dmitry S. Blinov

2016-06-01

Full Text Available Introduction. Tissues of the human body can conduct electricity. Liquid medium (water, blood, the contents of hollow bodies, have a low impedance, i.e. good conductors, while denser tissue (muscle, nerves, etc. resistance is significantly higher. The biggest impedance have fat and bone tissues. The bioimpendancemetry – a method which allows to determine the composition of the human body by measuring electrical resistance (impedance of its tissues. Relevance. This technique is indispensable to dieticians and fitness trainers. In addition, the results of the study can provide invaluable assistance in the appointment of effective treatment physicians, gynecologists, orthopedists, and other specialists. The bioimpedance method helps to determine the risks of developing diabetes type 2, atherosclerosis, hypertension, diseases of the musculoskeletal system, disorders of the endocrine system, gall-stone disease and etc. Materials and Methods. In the list of parameters of body composition assessed by bioimpedance analysis method, included absolute and relative indicators. Depending on the method of measurement of the absolute rates were determined for the whole body. To absolute performance were: fat and skinny body mass index, active cell and skeletal muscle mass, total body water, cellular and extracellular fluid. Along with them were calculated relatively (normalized to body weight, lean mass, or other variables indicators of body composition. Results. In the result of the comparison of anthropometric and bioimpedance method found that growth performance, vital capacity, weight, waist circumference, circumfer¬ence of waist and hip, basal metabolism, body fat mass, normalized on growth, lean mass, percentage skeletal muscle mass in boys and girls with normal and excessive body weight had statistically significant differences. Discussion and Conclusions. In the present study physical development with consideration of body composition in students

Methods for the computer-generated presentation of spatial objects for blind people on tactile media

OpenAIRE

Kurze, Martin

2010-01-01

This work first explores existing methods to present graphical information to blind people; focus is put on haptic presentation, i.e. a touchable form of presentation. The work emphasises an approach which does not try to make the existing graphics touchable which were designed with sighted perceivers in mind and thus contain optic hints regarding structure and position of certain geometric features (e.g. occlusion or perspective distortion); rather the presented content itself, the model is ...

Some GCM simulation results on present and possible future climate in northern Europe

Energy Technology Data Exchange (ETDEWEB)

Raeisaenen, J [Helsinki Univ. (Finland). Dept. of Meteorology

1996-12-31

The Intergovernmental Panel on Climate Change initiated in 1993 a project entitled `Evaluation of Regional Climate Simulations`. The two basic aims of this project were to assess the skill of current general circulation models (GCMs) in simulating present climate at a regional level and to intercompare the regional response of various GCMs to increased greenhouse gas concentrations. The public data base established for the comparison included simulation results from several modelling centres, but most of the data were available in the form of time-averaged seasonal means only, and important quantities like precipitation were totally lacking in many cases. This presentation summarizes the intercomparison results for surface air temperature and sea level pressure in northern Europe. The quality of the control simulations and the response of the models to increased CO{sub 2} are addressed in both winter (December-February) and summer (June-August)

Some GCM simulation results on present and possible future climate in northern Europe

Energy Technology Data Exchange (ETDEWEB)

Raeisaenen, J. [Helsinki Univ. (Finland). Dept. of Meteorology

1995-12-31

The Intergovernmental Panel on Climate Change initiated in 1993 a project entitled `Evaluation of Regional Climate Simulations`. The two basic aims of this project were to assess the skill of current general circulation models (GCMs) in simulating present climate at a regional level and to intercompare the regional response of various GCMs to increased greenhouse gas concentrations. The public data base established for the comparison included simulation results from several modelling centres, but most of the data were available in the form of time-averaged seasonal means only, and important quantities like precipitation were totally lacking in many cases. This presentation summarizes the intercomparison results for surface air temperature and sea level pressure in northern Europe. The quality of the control simulations and the response of the models to increased CO{sub 2} are addressed in both winter (December-February) and summer (June-August)

Genomes correction and assembling: present methods and tools

Science.gov (United States)

Wojcieszek, Michał; Pawełkowicz, Magdalena; Nowak, Robert; Przybecki, Zbigniew

2014-11-01

Recent rapid development of next generation sequencing (NGS) technologies provided significant impact into genomics field of study enabling implementation of many de novo sequencing projects of new species which was previously confined by technological costs. Along with advancement of NGS there was need for adjustment in assembly programs. New algorithms must cope with massive amounts of data computation in reasonable time limits and processing power and hardware is also an important factor. In this paper, we address the issue of assembly pipeline for de novo genome assembly provided by programs presently available for scientist both as commercial and as open - source software. The implementation of four different approaches - Greedy, Overlap - Layout - Consensus (OLC), De Bruijn and Integrated resulting in variation of performance is the main focus of our discussion with additional insight into issue of short and long reads correction.

A poster presentation as an evaluation method to facilitate reflective thinking skills in nursing education.

Science.gov (United States)

Chabeli, M M

2002-08-01

This article seeks to establish whether the poster presentation of a specific theme can facilitate the student's thinking skills in nursing education. A qualitative, exploratory, descriptive and contextual research design where twenty students volunteered to take part in the study by signing an informed consent was followed. Descriptive naïve sketches were used for data collection followed by individual interviews to validate the findings. Data was analysed by means of the descriptive method of open coding of Tesch (in Creswell, 1994:155). DENOSA's ethical standards for research (1998:7) were considered. The findings indicated both positive and negative perceptions. The positive perceptions were: a poster presentation as an evaluation method facilitates creative, critical and reflective thinking skills; group work facilitates student participation; it facilitates problem solving skills; it increases the student's independence and a sense of ownership; and the evaluation is fair. The negative perceptions were that there was a lack of clarity on the student's expectations and that group activity is difficult. Trustworthiness was maintained in accordance with Lincoln and Guba's principles (1985:290-327). It is concluded that a poster presentation, used effectively as an evaluation method, can facilitate the learner's critical and reflective thinking skills. It is recommended that other learner-centred methods of assessment and evaluation be researched for their effective use in facilitating the higher order thinking skills of learners.

Presentation as a method of displaying an idea

Directory of Open Access Journals (Sweden)

Марія Онищенко

2017-09-01

Full Text Available The questions of quality presentations to the scientific lectures are very important and modern. Сomputer presentations help to clearly give the necessary information, to enrich the text, to focus on the essentials. An effect of the performance on the audience is the most important thing in the presentation. The scientific presentation must be logically constructed, consistent, concise and vivid. There is the main rule for successful presentations: to tell the truth as a story with slides (pictures. Creating a presentation requires serious intellectual work and preparation that contains the following steps: 1 to estimate the audience and purpose; 2 to reflect a structure and content; 3 to develop a plan; 4 to write the text and prepare the slides; 5 to rehearse the performance. Slides should supplement or summarize the contents of the speech or its parts, but not duplicate it. Effective use of slides helps us understand that they have the maximum impact on the audience. It should also follow the rules of creating slides. Content of slides must comply with the performance. Information in slides should be presented logically, evenly and dosed. Basic facts and ideas are given in the final part. Students or young scientists should consider the design of the presentation as balanced, contrasting and relevant. Following the laws of composition, color, ergonomics is the required condition to accomplish this task. The presentation is not only the slides, it is the combination of many elements, the foremost of which is the speaker. Any presentation must conform to basic principles of psychology.

Economic Inequality in Presenting Vision in Shahroud, Iran: Two Decomposition Methods.

Science.gov (United States)

Mansouri, Asieh; Emamian, Mohammad Hassan; Zeraati, Hojjat; Hashemi, Hasan; Fotouhi, Akbar

2017-04-22

Visual acuity, like many other health-related problems, does not have an equal distribution in terms of socio-economic factors. We conducted this study to estimate and decompose economic inequality in presenting visual acuity using two methods and to compare their results in a population aged 40-64 years in Shahroud, Iran. The data of 5188 participants in the first phase of the Shahroud Cohort Eye Study, performed in 2009, were used for this study. Our outcome variable was presenting vision acuity (PVA) that was measured using LogMAR (logarithm of the minimum angle of resolution). The living standard variable used for estimation of inequality was the economic status and was constructed by principal component analysis on home assets. Inequality indices were concentration index and the gap between low and high economic groups. We decomposed these indices by the concentration index and BlinderOaxaca decomposition approaches respectively and compared the results. The concentration index of PVA was -0.245 (95% CI: -0.278, -0.212). The PVA gap between groups with a high and low economic status was 0.0705 and was in favor of the high economic group. Education, economic status, and age were the most important contributors of inequality in both concentration index and Blinder-Oaxaca decomposition. Percent contribution of these three factors in the concentration index and Blinder-Oaxaca decomposition was 41.1% vs. 43.4%, 25.4% vs. 19.1% and 15.2% vs. 16.2%, respectively. Other factors including gender, marital status, employment status and diabetes had minor contributions. This study showed that individuals with poorer visual acuity were more concentrated among people with a lower economic status. The main contributors of this inequality were similar in concentration index and Blinder-Oaxaca decomposition. So, it can be concluded that setting appropriate interventions to promote the literacy and income level in people with low economic status, formulating policies to address

Model films of cellulose. I. Method development and initial results

NARCIS (Netherlands)

Gunnars, S.; Wågberg, L.; Cohen Stuart, M.A.

2002-01-01

This report presents a new method for the preparation of thin cellulose films. NMMO (N- methylmorpholine- N-oxide) was used to dissolve cellulose and addition of DMSO (dimethyl sulfoxide) was used to control viscosity of the cellulose solution. A thin layer of the cellulose solution is spin- coated

Cytogenetical effects of low doses: results obtained by N.N.Luchik and present-day problems

International Nuclear Information System (INIS)

Geras'kin, S.A.; Sevan'kaev, A.V.

1996-01-01

The analysis of present status of the problem of quantitative assessment of cytogenetic effects low is presented. The importance of works of N.V. Luchik is demonstrated for the development of this field of radiobiology. The results of the author's own experimental and theoretical research on the regularities of induction of cytogenetical damage by low doses of ionising radiation are presented

A statistical method for testing epidemiological results, as applied to the Hanford worker population

International Nuclear Information System (INIS)

Brodsky, A.

1979-01-01

Some recent reports of Mancuso, Stewart and Kneale claim findings of radiation-produced cancer in the Hanford worker population. These claims are based on statistical computations that use small differences in accumulated exposures between groups dying of cancer and groups dying of other causes; actual mortality and longevity were not reported. This paper presents a statistical method for evaluation of actual mortality and longevity longitudinally over time, as applied in a primary analysis of the mortality experience of the Hanford worker population. Although available, this method was not utilized in the Mancuso-Stewart-Kneale paper. The author's preliminary longitudinal analysis shows that the gross mortality experience of persons employed at Hanford during 1943-70 interval did not differ significantly from that of certain controls, when both employees and controls were selected from families with two or more offspring and comparison were matched by age, sex, race and year of entry into employment. This result is consistent with findings reported by Sanders (Health Phys. vol.35, 521-538, 1978). The method utilizes an approximate chi-square (1 D.F.) statistic for testing population subgroup comparisons, as well as the cumulation of chi-squares (1 D.F.) for testing the overall result of a particular type of comparison. The method is available for computer testing of the Hanford mortality data, and could also be adapted to morbidity or other population studies. (author)

Presenting results as dynamically generated co-authorship subgraphs in semantic digital library collections

Directory of Open Access Journals (Sweden)

James Powell

2012-02-01

Full Text Available Semantic web representations of data are by definition graphs, and these graphs can be explored using concepts from graph theory. This paper demonstrates how semantically mapped bibliographic metadata, combined with a lightweight software architecture and Web-based graph visualization tools, can be used to generate dynamic authorship graphs in response to typical user queries, as an alternative to more common text-based results presentations. It also shows how centrality measures and path analysis techniques from social network analysis can be used to enhance the visualization of query results. The resulting graphs require modestly more cognitive engagement from the user but offer insights not available from text.

Mechanics of Nanostructures: Methods and Results

Science.gov (United States)

Ruoff, Rod

2003-03-01

We continue to develop and use new tools to measure the mechanics and electromechanics of nanostructures. Here we discuss: (a) methods for making nanoclamps and the resulting: nanoclamp geometry, chemical composition and type of chemical bonding, and nanoclamp strength (effectiveness as a nanoclamp for the mechanics measurements to be made); (b) mechanics of carbon nanocoils. We have received carbon nanocoils from colleagues in Japan [1], measured their spring constants, and have observed extensions exceeding 100% relative to the unloaded length, using our scanning electron microscope nanomanipulator tool; (c) several new devices that are essentially MEMS-based, that allow for improved measurements of the mechanics of psuedo-1D and planar nanostructures. [1] Zhang M., Nakayama Y., Pan L., Japanese J. Appl. Phys. 39, L1242-L1244 (2000).

Present status of NMCC and sample preparation method for bio-samples

International Nuclear Information System (INIS)

Futatsugawa, S.; Hatakeyama, S.; Saitou, S.; Sera, K.

1993-01-01

In NMCC(Nishina Memorial Cyclotron Center) we are doing researches on PET of nuclear medicine (Positron Emission Computed Tomography) and PIXE analysis (Particle Induced X-ray Emission) using a small cyclotron of compactly designed. The NMCC facilities have been opened to researchers of other institutions since April 1993. The present status of NMCC is described. Bio-samples (medical samples, plants, animals and environmental samples) have mainly been analyzed by PIXE in NMCC. Small amounts of bio-samples for PIXE are decomposed quickly and easily in a sealed PTFE (polytetrafluoroethylene) vessel with a microwave oven. This sample preparation method of bio-samples also is described. (author)

The reactive transport benchmark proposed by GdR MoMaS: presentation and first results

Energy Technology Data Exchange (ETDEWEB)

Carrayrou, J. [Institut de Mecanique des Fluides et des Solides, UMR ULP-CNRS 7507, 67 - Strasbourg (France); Lagneau, V. [Ecole des Mines de Paris, Centre de Geosciences, 77 - Fontainebleau (France)

2007-07-01

We present here the actual context of reactive transport modelling and the major numerical challenges. GdR MoMaS proposes a benchmark on reactive transport. We present this benchmark and some results obtained on it by two reactive transport codes HYTEC and SPECY. (authors)

The reactive transport benchmark proposed by GdR MoMaS: presentation and first results

International Nuclear Information System (INIS)

Carrayrou, J.; Lagneau, V.

2007-01-01

We present here the actual context of reactive transport modelling and the major numerical challenges. GdR MoMaS proposes a benchmark on reactive transport. We present this benchmark and some results obtained on it by two reactive transport codes HYTEC and SPECY. (authors)

Some results about the dating of pre hispanic mexican ceramics by the thermoluminescence method

International Nuclear Information System (INIS)

Gonzalez M, P.; Mendoza A, D.; Ramirez L, A.; Schaaf, P.

2004-01-01

One of the most frequently recurring questions in Archaeometry concerns the age of the studied objects. The some first dating methods were based in historical narrations, style of buildings manufacture techniques. However, has been observed that as consequence the continuous irradiation from naturally occurring radioisotopes and from cosmic rays some materials, such as archaeological ceramic, accumulate certain quantity of energy. These types of material can, in principle, be dated through the analysis of these accumulate energy. In that case, ceramic dating can be realized by thermoluminescence (TL) dating. In this work, results obtained by our research group about TL dating of ceramic belonging to several archaeological zones like to Edzna (Campeche), Calixtlahuaca and Teotenango (Mexico State) and Hervideros (Durango) are presented. The analysis was realized using the fine grained mode in a Daybreak model 1100 reader TL system. The radioisotopes that contribute in the accumulate annual dose in ceramic samples ( 40 K, 238 U, 232 Th) were determined by means of techniques such as Energy Dispersive X-ray Spectroscopy (EDS) and Neutron Activation Analysis (AAN). Our results are agree with results obtained through other methods. (Author) 7 refs., 2 tabs., 5 figs

The Use of Data Mining Methods to Predict the Result of Infertility Treatment Using the IVF ET Method

Directory of Open Access Journals (Sweden)

Malinowski Paweł

2014-12-01

Full Text Available The IVF ET method is a scientifically recognized infertility treat- ment method. The problem, however, is this method’s unsatisfactory efficiency. This calls for a more thorough analysis of the information available in the treat- ment process, in order to detect the factors that have an effect on the results, as well as to effectively predict result of treatment. Classical statistical methods have proven to be inadequate in this issue. Only the use of modern methods of data mining gives hope for a more effective analysis of the collected data. This work provides an overview of the new methods used for the analysis of data on infertility treatment, and formulates a proposal for further directions for research into increasing the efficiency of the predicted result of the treatment process.

Cloud detection method for Chinese moderate high resolution satellite imagery (Conference Presentation)

Science.gov (United States)

Zhong, Bo; Chen, Wuhan; Wu, Shanlong; Liu, Qinhuo

2016-10-01

Cloud detection of satellite imagery is very important for quantitative remote sensing research and remote sensing applications. However, many satellite sensors don't have enough bands for a quick, accurate, and simple detection of clouds. Particularly, the newly launched moderate to high spatial resolution satellite sensors of China, such as the charge-coupled device on-board the Chinese Huan Jing 1 (HJ-1/CCD) and the wide field of view (WFV) sensor on-board the Gao Fen 1 (GF-1), only have four available bands including blue, green, red, and near infrared bands, which are far from the requirements of most could detection methods. In order to solve this problem, an improved and automated cloud detection method for Chinese satellite sensors called OCM (Object oriented Cloud and cloud-shadow Matching method) is presented in this paper. It firstly modified the Automatic Cloud Cover Assessment (ACCA) method, which was developed for Landsat-7 data, to get an initial cloud map. The modified ACCA method is mainly based on threshold and different threshold setting produces different cloud map. Subsequently, a strict threshold is used to produce a cloud map with high confidence and large amount of cloud omission and a loose threshold is used to produce a cloud map with low confidence and large amount of commission. Secondly, a corresponding cloud-shadow map is also produced using the threshold of near-infrared band. Thirdly, the cloud maps and cloud-shadow map are transferred to cloud objects and cloud-shadow objects. Cloud and cloud-shadow are usually in pairs; consequently, the final cloud and cloud-shadow maps are made based on the relationship between cloud and cloud-shadow objects. OCM method was tested using almost 200 HJ-1/CCD images across China and the overall accuracy of cloud detection is close to 90%.

Wide Binaries in TGAS: Search Method and First Results

Science.gov (United States)

Andrews, Jeff J.; Chanamé, Julio; Agüeros, Marcel A.

2018-04-01

Half of all stars reside in binary systems, many of which have orbital separations in excess of 1000 AU. Such binaries are typically identified in astrometric catalogs by matching the proper motions vectors of close stellar pairs. We present a fully Bayesian method that properly takes into account positions, proper motions, parallaxes, and their correlated uncertainties to identify widely separated stellar binaries. After applying our method to the >2 × 106 stars in the Tycho-Gaia astrometric solution from Gaia DR1, we identify over 6000 candidate wide binaries. For those pairs with separations less than 40,000 AU, we determine the contamination rate to be ~5%. This sample has an orbital separation (a) distribution that is roughly flat in log space for separations less than ~5000 AU and follows a power law of a -1.6 at larger separations.

Qualitative Analysis Results for Applications of a New Fire Probabilistic Safety Assessment Method to Ulchin Unit 3

International Nuclear Information System (INIS)

Kang, Daeil; Kim, Kilyoo; Jang, Seungcheol

2013-01-01

The fire PRA Implementation Guide has been used for performing a fire PSA for NPPs in Korea. Recently, US NRC and EPRI developed a new fire PSA method, NUREG/CR-6850, to provide state-of-the-art methods, tools, and data for the conduct of a fire PSA for a commercial nuclear power plant (NPP). Due to the limited budget and man powers for the development of KSRP, hybrid PSA approaches, using NUREG/CR-6850 and Fire PRA Implementation Guide, will be employed for conducting a fire PSA of Ulchin Unit 3. In this paper, the qualitative analysis results for applications of a new fire PSA method to Ulchin Unit 3 are presented. This paper introduces the qualitative analysis results for applications of a new fire PSA method to Ulchin Unit 3. Compared with the previous industry, the number of fire areas for quantification identified and the number of equipment selected has increased

Integrate life-cycle assessment and risk analysis results, not methods.

Science.gov (United States)

Linkov, Igor; Trump, Benjamin D; Wender, Ben A; Seager, Thomas P; Kennedy, Alan J; Keisler, Jeffrey M

2017-08-04

Two analytic perspectives on environmental assessment dominate environmental policy and decision-making: risk analysis (RA) and life-cycle assessment (LCA). RA focuses on management of a toxicological hazard in a specific exposure scenario, while LCA seeks a holistic estimation of impacts of thousands of substances across multiple media, including non-toxicological and non-chemically deleterious effects. While recommendations to integrate the two approaches have remained a consistent feature of environmental scholarship for at least 15 years, the current perception is that progress is slow largely because of practical obstacles, such as a lack of data, rather than insurmountable theoretical difficulties. Nonetheless, the emergence of nanotechnology presents a serious challenge to both perspectives. Because the pace of nanomaterial innovation far outstrips acquisition of environmentally relevant data, it is now clear that a further integration of RA and LCA based on dataset completion will remain futile. In fact, the two approaches are suited for different purposes and answer different questions. A more pragmatic approach to providing better guidance to decision-makers is to apply the two methods in parallel, integrating only after obtaining separate results.

Evaluation of different methods for determining the angle of attack on wind turbine blades with CFD results under axial inflow conditions

DEFF Research Database (Denmark)

Rahimi, Vajiheh; Schepers, J.G.; Shen, Wen Zhong

2018-01-01

as shortcomings, are presented. The investigations are performed for two 10 MW reference wind turbines under axial inflow conditions, namely the turbines designed in the EU AVATAR and INNWIND.EU projects. The results show that the evaluated methods are in good agreement with each other at the mid-span, though......This work presents an investigation on different methods for the calculation of the angle of attack and the underlying induced velocity on wind turbine blades using data obtained from three-dimensional Computational Fluid Dynamics (CFD). Several methods are examined and their advantages, as well...

Beyond the floor effect on the Wechsler Intelligence Scale for Children--4th Ed. (WISC-IV): calculating IQ and Indexes of subjects presenting a floored pattern of results.

Science.gov (United States)

Orsini, A; Pezzuti, L; Hulbert, S

2015-05-01

It is now widely known that children with severe intellectual disability show a 'floor effect' on the Wechsler scales. This effect emerges because the practice of transforming raw scores into scaled scores eliminates any variability present in participants with low intellectual ability and because intelligence quotient (IQ) scores are limited insofar as they do not measure scores lower than 40. Following Hessl et al.'s results, the present authors propose a method for the computation of the Wechsler Intelligence Scale for Children--4th Ed. (WISC-IV)'s IQ and Indexes in intellectually disabled participants affected by a floored pattern of results. The Italian standardization sample (n = 2200) for the WISC-IV was used. The method presented in this study highlights the limits of the 'floor effect' of the WISC-IV in children with serious intellectual disability who present a profile with weighted scores of 1 in all the subtests despite some variability in the raw scores. Such method eliminates the floor effect of the scale and therefore makes it possible to analyse the strengths and weaknesses of the WISC-IV's Indexes in these participants. The Authors reflect on clinical utility of this method and on the meaning of raw score of 0 on subtest. © 2014 MENCAP and International Association of the Scientific Study of Intellectual and Developmental Disabilities and John Wiley & Sons Ltd.

Results from the Application of Uncertainty Methods in the CSNI Uncertainty Methods Study (UMS)

International Nuclear Information System (INIS)

Glaeser, H.

2008-01-01

Within licensing procedures there is the incentive to replace the conservative requirements for code application by a - best estimate - concept supplemented by an uncertainty analysis to account for predictive uncertainties of code results. Methods have been developed to quantify these uncertainties. The Uncertainty Methods Study (UMS) Group, following a mandate from CSNI, has compared five methods for calculating the uncertainty in the predictions of advanced -best estimate- thermal-hydraulic codes. Most of the methods identify and combine input uncertainties. The major differences between the predictions of the methods came from the choice of uncertain parameters and the quantification of the input uncertainties, i.e. the wideness of the uncertainty ranges. Therefore, suitable experimental and analytical information has to be selected to specify these uncertainty ranges or distributions. After the closure of the Uncertainty Method Study (UMS) and after the report was issued comparison calculations of experiment LSTF-SB-CL-18 were performed by University of Pisa using different versions of the RELAP 5 code. It turned out that the version used by two of the participants calculated a 170 K higher peak clad temperature compared with other versions using the same input deck. This may contribute to the differences of the upper limit of the uncertainty ranges.

German precursor study: methods and results

International Nuclear Information System (INIS)

Hoertner, H.; Frey, W.; von Linden, J.; Reichart, G.

1985-01-01

This study has been prepared by the GRS by contract of the Federal Minister of Interior. The purpose of the study is to show how the application of system-analytic tools and especially of probabilistic methods on the Licensee Event Reports (LERs) and on other operating experience can support a deeper understanding of the safety-related importance of the events reported in reactor operation, the identification of possible weak points, and further conclusions to be drawn from the events. Additionally, the study aimed at a comparison of its results for the severe core damage frequency with those of the German Risk Study as far as this is possible and useful. The German Precursor Study is a plant-specific study. The reference plant is Biblis NPP with its very similar Units A and B, whereby the latter was also the reference plant for the German Risk Study

Screening of clonal chromosome aberrations present in A-bomb survivors by FISH method

International Nuclear Information System (INIS)

Nakano, Mimako; Kodama, Yoshiaki; Ito, Masahiro; Otaki, Kazuo; Nakamura, Nori

1997-01-01

Significance of FISH method for detection of clonal chromosome aberration was reviewed. A clonal chromosome aberration is derived from one abnormal cell clone and gives the influence on the frequency of the aberration. As well, the size and frequency of the aberration give an important information concerning lymphocyte kinetics. FISH method is meaningful for detection of the clonal aberration. Fifteen kinds of clonal aberrations were detected in A-bomb survivors, of which 10 were specifically detected by the method, indicating that its detection rate was 2-3 time as high as the ordinary method. The results were those on the DNA probe on no.1, no.2 and no.3 chromosomes, which consisting of about 23% of the genome. (K.H.)

Childhood sarcoidosis in Denmark 1979-1994: incidence, clinical features and laboratory results at presentation in 48 children

DEFF Research Database (Denmark)

Hoffmann, A L; Milman, N; Byg, K E

2004-01-01

AIM: To describe the incidence, clinical presentation and paraclinical findings in childhood sarcoidosis in Denmark, 1979-1994. METHODS: Patients (n = 5536) with a diagnosis of sarcoidosis were drawn from the nationwide Patient Registry; 81 patients were ... examination (glucose, albumin, haemoglobin) was normal in 96% of the patients; the patient with nephrocalcinosis had albuminuria and haematuria. CONCLUSION: The incidence of sarcoidosis in Danish children is low and increases with age. Sarcoidosis in young children may present clinical features...... that are different from the appearance of those in older children and often constitute a diagnostic challenge. In older children, the clinical appearance has many features in common with the presentation in adults....

Advanced Presentation of BETHSY 6.2TC Test Results Calculated by RELAP5 and TRACE

Directory of Open Access Journals (Sweden)

Andrej Prošek

2012-01-01

Full Text Available Today most software applications come with a graphical user interface, including U.S. Nuclear Regulatory Commission TRAC/RELAP Advanced Computational Engine (TRACE best-estimate reactor system code. The graphical user interface is called Symbolic Nuclear Analysis Package (SNAP. The purpose of the present study was to assess the TRACE computer code and to assess the SNAP capabilities for input deck preparation and advanced presentation of the results. BETHSY 6.2 TC test was selected, which is 15.24 cm equivalent diameter horizontal cold leg break. For calculations the TRACE V5.0 Patch 1 and RELAP5/MOD3.3 Patch 4 were used. The RELAP5 legacy input deck was converted to TRACE input deck using SNAP. The RELAP5 and TRACE comparison to experimental data showed that TRACE results are as good as or better than the RELAP5 calculated results. The developed animation masks were of great help in comparison of results and investigating the calculated physical phenomena and processes.

Does parent-child agreement vary based on presenting problems? Results from a UK clinical sample.

Science.gov (United States)

Cleridou, Kalia; Patalay, Praveetha; Martin, Peter

2017-01-01

Discrepancies are often found between child and parent reports of child psychopathology, nevertheless the role of the child's presenting difficulties in relation to these is underexplored. This study investigates whether parent-child agreement on the conduct and emotional scales of the Strengths and Difficulties Questionnaire (SDQ) varied as a result of certain child characteristics, including the child's presenting problems to clinical services, age and gender. The UK-based sample consisted of 16,754 clinical records of children aged 11-17, the majority of which were female (57%) and White (76%). The dataset was provided by the Child Outcomes Research Consortium , which collects outcome measures from child services across the UK. Clinicians reported the child's presenting difficulties, and parents and children completed the SDQ. Using correlation analysis, the main findings indicated that agreement varied as a result of the child's difficulties for reports of conduct problems, and this seemed to be related to the presence or absence of externalising difficulties in the child's presentation. This was not the case for reports of emotional difficulties. In addition, agreement was higher when reporting problems not consistent with the child's presentation; for instance, agreement on conduct problems was greater for children presenting with internalising problems. Lastly, the children's age and gender did not seem to have an impact on agreement. These findings demonstrate that certain child presenting difficulties, and in particular conduct problems, may be related to informant agreement and need to be considered in clinical practice and research. Trial Registration This study was observational and as such did not require trial registration.

Potential theory for stationary Schrödinger operators: a survey of results obtained with non-probabilistic methods

Directory of Open Access Journals (Sweden)

Marco Bramanti

1992-05-01

Full Text Available In this paper we deal with a uniformly elliptic operator of the kind: Lu  Au + Vu, where the principal part A is in divergence form, and V is a function assumed in a “Kato class”. This operator has been studied in different contexts, especially using probabilistic techniques. The aim of the present work is to give a unified and simplified presentation of the results obtained with non probabilistic methods for the operator L on a bounded Lipschitz domain. These results regard: continuity of the solutions of Lu=0; Harnack inequality; estimates on the Green's function and L-harmonic measure; boundary behavior of positive solutions of Lu=0, in particular a “Fatou's theorem”.

Evaluating rehabilitation methods - some practical results from Rum Jungle

International Nuclear Information System (INIS)

Ryan, P.

1987-01-01

Research and analysis of the following aspects of rehabilitation have been conducted at the Rum Jungle mine site over the past three years: drainage structure stability; rock batter stability; soil fauna; tree growth in compacted soils; rehabilitation costs. The results show that, for future rehabilitation projects adopting refined methods, attention to final construction detail and biospheric influences is most important. The mine site offers a unique opportunity to evaluate the success of a variety of rehabilitation methods to the benefit of the industry in Australia overseas. It is intended that practical, economic, research will continue for some considerable time

Distribution of hemoglobinopathies in patients presenting for electrophoresis and comparison of result with High performance liquid chromatography

Directory of Open Access Journals (Sweden)

R Jha

2015-09-01

Full Text Available Background: Nearly 226 million carriers of thalassemias and abnormal hemoglobin are present worldwide according to the World Health Organization (WHO. The laboratory plays an important role in the investigation of the thalassemias and hemoglobinopathies. Cellulose acetate electrophoresis at alkaline pH and diagnosis based mainly on visual impression of thickness of band may miss the thalassemic trait patients. The aim of this study was to find out different hemoglobinopathies and thalassemia presenting in our hospital and to compare electrophoresis results with HPLC.Materials and Methods: This study was performed in the hematopathology section of Department of Pathology of Tribhuvan University Teaching Hospital on cases sent for electrophoresis during 18 months period from October 2013 to March 2015 and included hemoglobinopathies and thalassemias identified by either electrophoresis or HPLC. 97 cases fulfilled the inclusion criteria and thus were included in the study. Electrophoresis at alkaline pH was done in all whereas HPLC was performed in 27 cases.Results: A sharp peak of hemoglobinopathies and thalassemias was seen in Tharu community though other communities are also affected. Thalassemia trait was the most common diagnosis (26.8% followed by sickle cell anemia (21.6%.  Electrophoresis was efficient in detecting some alpha thalassemia variants but missed many cases of beta thalassemia trait.Conclusion: Beta Thalassemia trait and sickle cell anemia both are common in Nepal , along with some other hemoglobinopathies  A sharp peak of hemoglobinopathies and thalassemias are seen in Tharu community. These abnormal hemoglobins and thalassemias are mainly seen in Terai region. Electrophoresis fails to quantify hemoglobin percentage and thus is not appropriate test in beta thalassemia screening. 

A simplified presentation of the multigroup analytic nodal method in 2-D Cartesian geometry

International Nuclear Information System (INIS)

Hebert, Alain

2008-01-01

The nodal diffusion algorithms used in many production reactor simulation codes are originating from a common ancestry developed in the 1970s, the analytic nodal method (ANM) of the QUANDRY code. However, this original presentation of the ANM is complex and makes difficult the calculation of the nodal coupling matrices. Moreover, QUANDRY is limited to two-energy groups and its generalization to more groups appears laborious. We are presenting a simplified implementation of the ANM requiring only limited programming work. This formulation is consistent with the initial QUANDRY implementation and is easily generalizable to arbitrary G-group problems. A Matlab script is provided to highlight the simplicity of our presentation. For the sake of clarity, our implementation is limited to G-group, 2-D Cartesian geometry

Finite elements volumes methods: applications to the Navier-Stokes equations and convergence results

International Nuclear Information System (INIS)

Emonot, P.

1992-01-01

In the first chapter are described the equations modeling incompressible fluid flow and a quick presentation of finite volumes method. The second chapter is an introduction to the finite elements volumes method. The box model is described and a method adapted to Navier-Stokes problems is proposed. The third chapter shows a fault analysis of the finite elements volumes method for the Laplacian problem and some examples in one, two, three dimensional calculations. The fourth chapter is an extension of the error analysis of the method for the Navier-Stokes problem

Convergence results for a class of abstract continuous descent methods

Directory of Open Access Journals (Sweden)

Sergiu Aizicovici

2004-03-01

Full Text Available We study continuous descent methods for the minimization of Lipschitzian functions defined on a general Banach space. We establish convergence theorems for those methods which are generated by approximate solutions to evolution equations governed by regular vector fields. Since the complement of the set of regular vector fields is $sigma$-porous, we conclude that our results apply to most vector fields in the sense of Baire's categories.

Method of vacuum correlation functions: Results and prospects

International Nuclear Information System (INIS)

Badalian, A. M.; Simonov, Yu. A.; Shevchenko, V. I.

2006-01-01

Basic results obtained within the QCD method of vacuum correlation functions over the past 20 years in the context of investigations into strong-interaction physics at the Institute of Theoretical and Experimental Physics (ITEP, Moscow) are formulated Emphasis is placed primarily on the prospects of the general theory developed within QCD by employing both nonperturbative and perturbative methods. On the basis of ab initio arguments, it is shown that the lowest two field correlation functions play a dominant role in QCD dynamics. A quantitative theory of confinement and deconfinement, as well as of the spectra of light and heavy quarkonia, glueballs, and hybrids, is given in terms of these two correlation functions. Perturbation theory in a nonperturbative vacuum (background perturbation theory) plays a significant role, not possessing drawbacks of conventional perturbation theory and leading to the infrared freezing of the coupling constant α s

Factors associated with presenting late or with advanced HIV disease in the Netherlands, 1996–2014: results from a national observational cohort

Science.gov (United States)

Op de Coul, Eline L M; van Sighem, Ard; Brinkman, Kees; van Benthem, Birgit H; van der Ende, Marchina E; Geerlings, Suzanne; Reiss, Peter

2016-01-01

Objectives Early testing for HIV and entry into care are crucial to optimise treatment outcomes of HIV-infected patients and to prevent spread of HIV. We examined risk factors for presentation with late or advanced disease in HIV-infected patients in the Netherlands. Methods HIV-infected patients registered in care between January 1996 and June 2014 were selected from the ATHENA national observational HIV cohort. Risk factors for late presentation and advanced disease were analysed by multivariable logistic regression. Furthermore, geographical differences and time trends were examined. Results Of 20 965 patients, 53% presented with late-stage HIV infection, and 35% had advanced disease. Late presentation decreased from 62% (1996) to 42% (2013), while advanced disease decreased from 46% to 26%. Late presentation only declined significantly among men having sex with men (MSM; p Netherlands), and location of HIV diagnosis (hospital 3.27; 2.94 to 3.63, general practitioner 1.66; 1.50 to 1.83, antenatal screening 1.76; 1.38 to 2.34 vs sexually transmitted infection clinic). No association was found for socioeconomic status or level of urbanisation. Compared with Amsterdam, 2 regions had higher adjusted odds and 2 regions had lower odds of late presentation. Results were highly similar for advanced disease. Conclusions Although the overall rate of late presentation is declining in the Netherlands, targeted programmes to reduce late HIV diagnoses remain needed for all risk groups, but should be prioritised for heterosexual males, migrant populations, people aged ≥50 years and certain regions in the Netherlands. PMID:26729389

Integrating Quantitative and Qualitative Results in Health Science Mixed Methods Research Through Joint Displays.

Science.gov (United States)

Guetterman, Timothy C; Fetters, Michael D; Creswell, John W

2015-11-01

Mixed methods research is becoming an important methodology to investigate complex health-related topics, yet the meaningful integration of qualitative and quantitative data remains elusive and needs further development. A promising innovation to facilitate integration is the use of visual joint displays that bring data together visually to draw out new insights. The purpose of this study was to identify exemplar joint displays by analyzing the various types of joint displays being used in published articles. We searched for empirical articles that included joint displays in 3 journals that publish state-of-the-art mixed methods research. We analyzed each of 19 identified joint displays to extract the type of display, mixed methods design, purpose, rationale, qualitative and quantitative data sources, integration approaches, and analytic strategies. Our analysis focused on what each display communicated and its representation of mixed methods analysis. The most prevalent types of joint displays were statistics-by-themes and side-by-side comparisons. Innovative joint displays connected findings to theoretical frameworks or recommendations. Researchers used joint displays for convergent, explanatory sequential, exploratory sequential, and intervention designs. We identified exemplars for each of these designs by analyzing the inferences gained through using the joint display. Exemplars represented mixed methods integration, presented integrated results, and yielded new insights. Joint displays appear to provide a structure to discuss the integrated analysis and assist both researchers and readers in understanding how mixed methods provides new insights. We encourage researchers to use joint displays to integrate and represent mixed methods analysis and discuss their value. © 2015 Annals of Family Medicine, Inc.

A semantics-based method for clustering of Chinese web search results

Science.gov (United States)

Zhang, Hui; Wang, Deqing; Wang, Li; Bi, Zhuming; Chen, Yong

2014-01-01

Information explosion is a critical challenge to the development of modern information systems. In particular, when the application of an information system is over the Internet, the amount of information over the web has been increasing exponentially and rapidly. Search engines, such as Google and Baidu, are essential tools for people to find the information from the Internet. Valuable information, however, is still likely submerged in the ocean of search results from those tools. By clustering the results into different groups based on subjects automatically, a search engine with the clustering feature allows users to select most relevant results quickly. In this paper, we propose an online semantics-based method to cluster Chinese web search results. First, we employ the generalised suffix tree to extract the longest common substrings (LCSs) from search snippets. Second, we use the HowNet to calculate the similarities of the words derived from the LCSs, and extract the most representative features by constructing the vocabulary chain. Third, we construct a vector of text features and calculate snippets' semantic similarities. Finally, we improve the Chameleon algorithm to cluster snippets. Extensive experimental results have shown that the proposed algorithm has outperformed over the suffix tree clustering method and other traditional clustering methods.

Portuguese Familial Hypercholesterolemia Study: presentation of the study and preliminary results.

Science.gov (United States)

Bourbon, Mafalda; Rato, Quitéria

2006-11-01

Familial hypercholesterolemia (FH) is an autosomal dominant genetic disorder caused, in the majority of cases, by a partial or total lack of functional low density lipoprotein receptors (LDLR). Mutations in the LDLR gene lead to increased plasma cholesterol levels, resulting in cholesterol deposition in the arteries, thereby increasing the risk of premature coronary heart disease. The homozygous form of FH is rare but heterozygous FH is common, although underdiagnosed in many populations, including the Portuguese. In 1999 the Portuguese Familial Hypercholesterolemia Study was begun at the National Institute of Health. The aim of the Portuguese Familial H ypercholesterolemia Study is to perform an epidemiological study to determine the prevalence and distribution of FH in Portugal and to better understand the pathophysiology of coronary heart disease in these patients. The aim of the present work is to present the study's criteria and organization as well as its preliminary results. The study population consists of individuals of both sexes and all ages with a clinical diagnosis of FH, with biochemical and molecular characterization being performed. The clinical criteria used for the diagnosis of FH were adapted from those of the Simon Broome Heart Research Trust. The study is organized in five stages: 1. selection of individuals with a clinical diagnosis of FH; 2. completion of a clinical questionnaire and declaration of informed consent; 3. collection of blood samples; 4. biochemical characterization; 5. molecular study of three genes associated with the FH phenotype: LDLR, apolipoprotein B (APOB) and proprotein convertase subtilisin/kexin type 9 (PCSK9). Between 1999 and June 2006 the LDLR gene and the APOB gene of 141 index cases (38 children and 103 adults) were studied. In 78 of these index cases (76 heterozygotes and two homozygotes) 50 different mutations in the LDLR gene were identified, and two unrelated individuals were found to have the ApoB3500 mutation

Comparative study of methods on outlying data detection in experimental results

International Nuclear Information System (INIS)

Oliveira, P.M.S.; Munita, C.S.; Hazenfratz, R.

2009-01-01

The interpretation of experimental results through multivariate statistical methods might reveal the outliers existence, which is rarely taken into account by the analysts. However, their presence can influence the results interpretation, generating false conclusions. This paper shows the importance of the outliers determination for one data base of 89 samples of ceramic fragments, analyzed by neutron activation analysis. The results were submitted to five procedures to detect outliers: Mahalanobis distance, cluster analysis, principal component analysis, factor analysis, and standardized residual. The results showed that although cluster analysis is one of the procedures most used to identify outliers, it can fail by not showing the samples that are easily identified as outliers by other methods. In general, the statistical procedures for the identification of the outliers are little known by the analysts. (author)

ISO Results Presented at International Astronomical Union

Science.gov (United States)

1997-08-01

Some of the work being presented is collected in the attached ESA Information Note N 25-97, ISO illuminates our cosmic ancestry. A set of six colour images illustrating various aspects have also been released and are available at http://www.estec.esa.nl/spdwww/iso1808.htm or in hard copy from ESA Public Relations Paris (fax:+33.1.5369.7690). These pictures cover: 1. Distant but powerful infrared galaxies 2. A scan across the milky way 3. Helix nebula: the shroud of a dead star 4. Supernova remnant Cassiopeia A 5. Trifid nebula: a dusty birthplace of stars 6. Precursors of stars and planets The International Astronomical Union provides a forum where astronomers from all over the world can develop astronomy in all its aspects through international co-operation. General Assemblies are held every three years. It is expected that over 1600 astronomers will attend this year's meeting, which is being held in Kyoto, Japan from 18-30 August. Further information on the meeting can be found at: www.tenmon.or.jp/iau97/ . ISO illuminates our cosmic ancestry The European Space Agency's Infrared Space Observatory, ISO, is unmatched in its ability to explore and analyse many of the universal processes that made our existence possible. We are children of the stars. Every atom in our bodies was created in cosmic space and delivered to the Sun's vicinity in time for the Earth's formation, during a ceaseless cycle of birth, death and rebirth among the stars. The most creative places in the sky are cool and dusty, and opaque even to the Hubble Space Telescope. Infrared rays penetrating the dust reveal to ISO hidden objects, and the atoms and molecules of cosmic chemistry. "ISO is reading Nature's recipe book," says Roger Bonnet, ESA's director of science. "As the world's only telescope capable of observing the Universe over a wide range of infrared wavelengths, ISO plays an indispensable part in astronomical discoveries that help to explain how we came to exist." This Information Note

The Past, Present, and Future of Research in Distance Education: Results of a Content Analysis

Science.gov (United States)

Lee, Youngmin; Driscoll, Marcy P.; Nelson, David W.

2005-01-01

The articles published in four prominent distance education journals between 1997 and 2002 were categorized and the references cited were tallied. The study provides an opportunity to examine research topics, methods, and citation trends. The results can be used to review current research trends and to explore potential research directions.…

Soil Particle Size Analysis by Laser Diffractometry: Result Comparison with Pipette Method

Science.gov (United States)

Šinkovičová, Miroslava; Igaz, Dušan; Kondrlová, Elena; Jarošová, Miriam

2017-10-01

Soil texture as the basic soil physical property provides a basic information on the soil grain size distribution as well as grain size fraction representation. Currently, there are several methods of particle dimension measurement available that are based on different physical principles. Pipette method based on the different sedimentation velocity of particles with different diameter is considered to be one of the standard methods of individual grain size fraction distribution determination. Following the technical advancement, optical methods such as laser diffraction can be also used nowadays for grain size distribution determination in the soil. According to the literature review of domestic as well as international sources related to this topic, it is obvious that the results obtained by laser diffractometry do not correspond with the results obtained by pipette method. The main aim of this paper was to analyse 132 samples of medium fine soil, taken from the Nitra River catchment in Slovakia, from depths of 15-20 cm and 40-45 cm, respectively, using laser analysers: ANALYSETTE 22 MicroTec plus (Fritsch GmbH) and Mastersizer 2000 (Malvern Instruments Ltd). The results obtained by laser diffractometry were compared with pipette method and the regression relationships using linear, exponential, power and polynomial trend were derived. Regressions with the three highest regression coefficients (R2) were further investigated. The fit with the highest tightness was observed for the polynomial regression. In view of the results obtained, we recommend using the estimate of the representation of the clay fraction (analysis is done according to laser diffractometry. The advantages of laser diffraction method comprise the short analysis time, usage of small sample amount, application for the various grain size fraction and soil type classification systems, and a wide range of determined fractions. Therefore, it is necessary to focus on this issue further to address the

[Integrated intensive treatment of tinnitus: method and initial results].

Science.gov (United States)

Mazurek, B; Georgiewa, P; Seydel, C; Haupt, H; Scherer, H; Klapp, B F; Reisshauer, A

2005-07-01

In recent years, no major advances have been made in understanding the mechanisms underlying the development of tinnitus. Hence, the present therapeutic strategies aim at decoupling the subconscious from the perception of tinnitus. Mindful of the lessons drawn from existing tinnitus retraining and desensitisation therapies, a new integrated day hospital strategy of treatment lasting 7-14 days has been developed at the Charité Hospital and is presented in the present paper. The strategy for treating tinnitus in the proximity of patient domicile is designed for patients who feel disturbed in their world of perception and their efficiency due to tinnitus and give evidence of mental and physical strain. In view of the etiologically non-uniform and multiple events connected with tinnitus, consideration was also given to the fact that somatic and psychosocial factors are equally involved. Therefore, therapy should aim at diagnosing and therapeutically influencing those psychosocial factors that reduce the hearing impression to such an extent that the affected persons suffer from strain. The first results of therapy-dependent changes of 46 patients suffering from chronic tinnitus are presented. The data were evaluated before and after 7 days of treatment and 6 months after the end of treatment. Immediately after the treatment, the scores of both the tinnitus questionnaire (Goebel and Hiller) and the subscales improved significantly. These results were maintained during the 6-month post-treatment period and even improved.

Human exposure to bisphenol A by biomonitoring: Methods, results and assessment of environmental exposures

International Nuclear Information System (INIS)

Dekant, Wolfgang; Voelkel, Wolfgang

2008-01-01

Human exposure to bisphenol A is controversially discussed. This review critically assesses methods for biomonitoring of bisphenol A exposures and reported concentrations of bisphenol A in blood and urine of non-occupationally ('environmentally') exposed humans. From the many methods published to assess bisphenol A concentrations in biological media, mass spectrometry-based methods are considered most appropriate due to high sensitivity, selectivity and precision. In human blood, based on the known toxicokinetics of bisphenol A in humans, the expected very low concentrations of bisphenol A due to rapid biotransformation and the very rapid excretion result in severe limitations in the use of reported blood levels of bisphenol A for exposure assessment. Due to the rapid and complete excretion of orally administered bisphenol A, urine samples are considered as the appropriate body fluid for bisphenol A exposure assessment. In urine samples from several cohorts, bisphenol A (as glucuronide) was present in average concentrations in the range of 1-3 μg/L suggesting that daily human exposure to bisphenol A is below 6 μg per person (< 0.1 μg/kg bw/day) for the majority of the population

TMI-2 core debris analytical methods and results

International Nuclear Information System (INIS)

Akers, D.W.; Cook, B.A.

1984-01-01

A series of six grab samples was taken from the debris bed of the TMI-2 core in early September 1983. Five of these samples were sent to the Idaho National Engineering Laboratory for analysis. Presented is the analysis strategy for the samples and some of the data obtained from the early stages of examination of the samples (i.e., particle size-analysis, gamma spectrometry results, and fissile/fertile material analysis)

On a new iterative method for solving linear systems and comparison results

Science.gov (United States)

Jing, Yan-Fei; Huang, Ting-Zhu

2008-10-01

In Ujevic [A new iterative method for solving linear systems, Appl. Math. Comput. 179 (2006) 725-730], the author obtained a new iterative method for solving linear systems, which can be considered as a modification of the Gauss-Seidel method. In this paper, we show that this is a special case from a point of view of projection techniques. And a different approach is established, which is both theoretically and numerically proven to be better than (at least the same as) Ujevic's. As the presented numerical examples show, in most cases, the convergence rate is more than one and a half that of Ujevic.

Improvement of human cell line activation test (h-CLAT) using short-time exposure methods for prevention of false-negative results.

Science.gov (United States)

Narita, Kazuto; Ishii, Yuuki; Vo, Phuc Thi Hong; Nakagawa, Fumiko; Ogata, Shinichi; Yamashita, Kunihiko; Kojima, Hajime; Itagaki, Hiroshi

2018-01-01

Recently, animal testing has been affected by increasing ethical, social, and political concerns regarding animal welfare. Several in vitro safety tests for evaluating skin sensitization, such as the human cell line activation test (h-CLAT), have been proposed. However, similar to other tests, the h-CLAT has produced false-negative results, including in tests for acid anhydride and water-insoluble chemicals. In a previous study, we demonstrated that the cause of false-negative results from phthalic anhydride was hydrolysis by an aqueous vehicle, with IL-8 release from THP-1 cells, and that short-time exposure to liquid paraffin (LP) dispersion medium could reduce false-negative results from acid anhydrides. In the present study, we modified the h-CLAT by applying this exposure method. We found that the modified h-CLAT is a promising method for reducing false-negative results obtained from acid anhydrides and chemicals with octanol-water partition coefficients (LogK ow ) greater than 3.5. Based on the outcomes from the present study, a combination of the original and the modified h-CLAT is suggested for reducing false-negative results. Notably, the combination method provided a sensitivity of 95% (overall chemicals) or 93% (chemicals with LogK ow > 2.0), and an accuracy of 88% (overall chemicals) or 81% (chemicals with LogK ow > 2.0). We found that the combined method is a promising evaluation scheme for reducing false-negative results seen in existing in vitro skin-sensitization tests. In the future, we expect a combination of original and modified h-CLAT to be applied in a newly developed in vitro test for evaluating skin sensitization.

First results of Minimum Fisher Regularisation as unfolding method for JET NE213 liquid scintillator neutron spectrometry

International Nuclear Information System (INIS)

Mlynar, Jan; Adams, John M.; Bertalot, Luciano; Conroy, Sean

2005-01-01

At JET, the NE213 liquid scintillator is being validated as a diagnostic tool for spectral measurements of neutrons emitted from the plasma. Neutron spectra have to be unfolded from the measured pulse-height spectra, which is an ill-conditioned problem. Therefore, use of two independent unfolding methods allows for less ambiguity on the interpretation of the data. In parallel to the routine algorithm MAXED based on the Maximum Entropy method, the Minimum Fisher Regularisation (MFR) method has been introduced at JET. The MFR method, known from two-dimensional tomography applications, has proved to provide a new transparent tool to validate the JET neutron spectra measured with the NE213 liquid scintillators. In this article, the MFR method applicable to spectra unfolding is briefly explained. After a mention of MFR tests on phantom spectra experimental neutron spectra are presented that were obtained by applying MFR to NE213 data in selected JET experiments. The results tend to confirm MAXED observations

Presentation of a Software Method for Use of Risk Assessment in Building Fire Safety Measure Optimization

Directory of Open Access Journals (Sweden)

A. R. Koohpaei

2012-05-01

Full Text Available Background and aims: The property loss and physical injuries due to fire events in buildings demonstrate the necessity of implementation of efficient and performance based fire safety measures. Effective and high efficiency protection is possible when design and selection of protection measures are based on risk assessment. This study aims at presenting a software method to make possible selection and design of building fire safety measures based upon quantitative risk assessment and building characteristics. Methods: based on “Fire Risk Assessment Method for Engineer (FRAME” a program in MATLB software was written. The first section of this program, according to the FRAME method and based on the specification of a building, calculates the potential risk and acceptable risk level. In the second section, according to potential risk, acceptable risk level and the fire risk level that user want, program calculate concession of protective factor for that building.Results: The prepared software make it possible to assign the fire safety measure based on quantitative risk level and all building specifications. All calculations were performed with 0.001 of precision and the accuracy of this software was assessed with handmade calculations. During the use of the software if an error occurs in calculations, it can be distinguished in the output. Conclusion: Application of quantitative risk assessment is a suitable tool for increasing of efficiency in designing and execution of fire protection measure in building. With using this software the selected fire safety measure would be more efficient and suitable since the selection of fire safety measures performed on risk assessment and particular specification of a building. Moreover fire risk in the building can be managed easily and carefully.

Processing method and results of meteor shower radar observations

International Nuclear Information System (INIS)

Belkovich, O.I.; Suleimanov, N.I.; Tokhtasjev, V.S.

1987-01-01

Studies of meteor showers permit the solving of some principal problems of meteor astronomy: to obtain the structure of a stream in cross section and along its orbits; to retrace the evolution of particle orbits of the stream taking into account gravitational and nongravitational forces and to discover the orbital elements of its parent body; to find out the total mass of solid particles ejected from the parent body taking into account physical and chemical evolution of meteor bodies; and to use meteor streams as natural probes for investigation of the average characteristics of the meteor complex in the solar system. A simple and effective method of determining the flux density and mass exponent parameter was worked out. This method and its results are discussed

Comparison result of inversion of gravity data of a fault by particle swarm optimization and Levenberg-Marquardt methods.

Science.gov (United States)

Toushmalani, Reza

2013-01-01

The purpose of this study was to compare the performance of two methods for gravity inversion of a fault. First method [Particle swarm optimization (PSO)] is a heuristic global optimization method and also an optimization algorithm, which is based on swarm intelligence. It comes from the research on the bird and fish flock movement behavior. Second method [The Levenberg-Marquardt algorithm (LM)] is an approximation to the Newton method used also for training ANNs. In this paper first we discussed the gravity field of a fault, then describes the algorithms of PSO and LM And presents application of Levenberg-Marquardt algorithm, and a particle swarm algorithm in solving inverse problem of a fault. Most importantly the parameters for the algorithms are given for the individual tests. Inverse solution reveals that fault model parameters are agree quite well with the known results. A more agreement has been found between the predicted model anomaly and the observed gravity anomaly in PSO method rather than LM method.

Application of the Ssub(n)-method for reactors computations on BESM-6 computer by using 26-group constants in the sub-group presentation

International Nuclear Information System (INIS)

Rogov, A.D.

1975-01-01

Description of the computer program for reactor computation by application of the Ssub(n)-method in the two-dimensional XY and RZ geometries is given. These programs are used with application of the computer library of 26- group constats system taking into account the resonance structure of the cross sections in the subgroup presentation. Results of some systems computations are given and the results obtained are analysed. (author)

Childhood sarcoidosis in Denmark 1979-1994: incidence, clinical features and laboratory results at presentation in 48 children

DEFF Research Database (Denmark)

Hoffmann, A L; Milman, N; Byg, K E

2004-01-01

.7-15). In 1979-1994 the incidence was 0.29 per 100000 person-years incidence was 0.06 in children weight loss, abdominal discomfort, respiratory symptoms, lymphadenopathy......AIM: To describe the incidence, clinical presentation and paraclinical findings in childhood sarcoidosis in Denmark, 1979-1994. METHODS: Patients (n = 5536) with a diagnosis of sarcoidosis were drawn from the nationwide Patient Registry; 81 patients were ... examination (glucose, albumin, haemoglobin) was normal in 96% of the patients; the patient with nephrocalcinosis had albuminuria and haematuria. CONCLUSION: The incidence of sarcoidosis in Danish children is low and increases with age. Sarcoidosis in young children may present clinical features...

Summary of EPA's risk assessment results from the analysis of alternative methods of low-level waste disposal

International Nuclear Information System (INIS)

Bandrowski, M.S.; Hung, C.Y.; Meyer, G.L.; Rogers, V.C.

1987-01-01

Evaluation of the potential health risk and individual exposure from a broad number of disposal alternatives is an important part of EPA's program to develop generally applicable environmental standards for the land disposal of low-level radioactive wastes (LLW). The Agency has completed an analysis of the potential population health risks and maximum individual exposures from ten disposal methods under three different hydrogeological and climatic settings. This paper briefly describes the general input and analysis procedures used in the risk assessment for LLW disposal and presents their preliminary results. Some important lessons learned from simulating LLW disposal under a large variety of methods and conditions are identified

[DESCRIPTION AND PRESENTATION OF THE RESULTS OF ELECTROENCEPHALOGRAM PROCESSING USING AN INFORMATION MODEL].

Science.gov (United States)

Myznikov, I L; Nabokov, N L; Rogovanov, D Yu; Khankevich, Yu R

2016-01-01

The paper proposes to apply the informational modeling of correlation matrix developed by I.L. Myznikov in early 1990s in neurophysiological investigations, such as electroencephalogram recording and analysis, coherence description of signals from electrodes on the head surface. The authors demonstrate information models built using the data from studies of inert gas inhalation by healthy human subjects. In the opinion of the authors, information models provide an opportunity to describe physiological processes with a high level of generalization. The procedure of presenting the EEG results holds great promise for the broad application.

Present status of Kyoto University reactor research result data base KURRIP

International Nuclear Information System (INIS)

Takeuchi, Takayuki

1986-01-01

The construction of KURRIP data base was begun in 1982, and in 1983, the data base concerning the literatures published in five years from 1978 to 1982 was set up in the Kyoto University Large Computer Center, and it has become available generally. In fiscal year 1984, the data concerning the literatures published from 1974 to 1977 and in 1983 were added. Moreover in this fiscal year, the work is carried out to input the data concerning the literatures published from 1970 to 1973 and in 1984. The data retrievable at present are those for ten years from 1974 to 1983. The results of having retrieved these data about a number of items are reported in this paper. The classification according to the places of employment of authors, the classification according to the kinds of literatures, the classification according to the languages used, the classification according to the installations used, the classification according to the fields of research, and the classification according to the magazines which printed the data are reported. (Kako, I.)

Quality of claims, references and the presentation of risk results in medical journal advertising: a comparative study in Australia, Malaysia and the United States

Directory of Open Access Journals (Sweden)

Vitry Agnes I

2010-05-01

Full Text Available Abstract Background Journal advertising is used by pharmaceutical companies to disseminate medicine information to doctors. The quality of claims, references and the presentation of risk results in Australia and the US has been questioned in several studies. No recent evidence is available on the quality of claims, references and the presentation of risk results in journal advertising in Australia and the US and no Malaysian data have been published. The aim of this study was to compare the quality of claims, references and the presentation of risk results in journal advertising in these three countries. Methods A consecutive sample of 85 unique advertisements from each country was selected from journal advertising published between January 2004 to December 2006. Claims, references and the presentation of risk results in medical journal advertising were compared between the three countries. Results Less than one-third of the claims were unambiguous claims (Australia, 30%, Malaysia 17%, US, 23%. In Malaysia significantly less unambiguous claims were provided than in Australia and the US (P Conclusions The majority of claims were vague suggesting poor quality of claims in journal advertising in these three countries. Evidence from a randomized controlled trial, systematic review or meta- analysis was commonly cited to support claims. However, the more frequent use of data that have not been published and independently reviewed in the US compared to Australia and Malaysia raises questions on the quality of references in the US. The use of relative rather than absolute benefits may overemphasize the benefit of medicines which may leave doctors susceptible to misinterpreting information.

Pion emission from the T2K replica target: method, results and application

CERN Document Server

Abgrall, N.; Anticic, T.; Antoniou, N.; Argyriades, J.; Baatar, B.; Blondel, A.; Blumer, J.; Bogomilov, M.; Bravar, A.; Brooks, W.; Brzychczyk, J.; Bubak, A.; Bunyatov, S.A.; Busygina, O.; Christakoglou, P.; Chung, P.; Czopowicz, T.; Davis, N.; Debieux, S.; Di Luise, S.; Dominik, W.; Dumarchez, J.; Dynowski, K.; Engel, R.; Ereditato, A.; Esposito, L.S.; Feofilov, G.A.; Fodor, Z.; Ferrero, A.; Fulop, A.; Gazdzicki, M.; Golubeva, M.; Grabez, B.; Grebieszkow, K.; Grzeszczuk, A.; Guber, F.; Haesler, A.; Hakobyan, H.; Hasegawa, T.; Idczak, R.; Igolkin, S.; Ivanov, Y.; Ivashkin, A.; Kadija, K.; Kapoyannis, A.; Katrynska, N.; Kielczewska, D.; Kikola, D.; Kirejczyk, M.; Kisiel, J.; Kiss, T.; Kleinfelder, S.; Kobayashi, T.; Kochebina, O.; Kolesnikov, V.I.; Kolev, D.; Kondratiev, V.P.; Korzenev, A.; Kowalski, S.; Krasnoperov, A.; Kuleshov, S.; Kurepin, A.; Lacey, R.; Larsen, D.; Laszlo, A.; Lyubushkin, V.V.; Mackowiak-Pawlowska, M.; Majka, Z.; Maksiak, B.; Malakhov, A.I.; Maletic, D.; Marchionni, A.; Marcinek, A.; Maris, I.; Marin, V.; Marton, K.; Matulewicz, T.; Matveev, V.; Melkumov, G.L.; Messina, M.; Mrowczynski, St.; Murphy, S.; Nakadaira, T.; Nishikawa, K.; Palczewski, T.; Palla, G.; Panagiotou, A.D.; Paul, T.; Peryt, W.; Petukhov, O.; Planeta, R.; Pluta, J.; Popov, B.A.; Posiadala, M.; Pulawski, S.; Puzovic, J.; Rauch, W.; Ravonel, M.; Renfordt, R.; Robert, A.; Rohrich, D.; Rondio, E.; Rossi, B.; Roth, M.; Rubbia, A.; Rustamov, A.; Rybczynski, M.; Sadovsky, A.; Sakashita, K.; Savic, M.; Sekiguchi, T.; Seyboth, P.; Shibata, M.; Sipos, M.; Skrzypczak, E.; Slodkowski, M.; Staszel, P.; Stefanek, G.; Stepaniak, J.; Strabel, C.; Strobele, H.; Susa, T.; Szuba, M.; Tada, M.; Taranenko, A.; Tereshchenko, V.; Tolyhi, T.; Tsenov, R.; Turko, L.; Ulrich, R.; Unger, M.; Vassiliou, M.; Veberic, D.; Vechernin, V.V.; Vesztergombi, G.; Wilczek, A.; Wlodarczyk, Z.; Wojtaszek-Szwarc, A.; Wyszynski, O.; Zambelli, L.; Zipper, W.; Hartz, M.; Ichikawa, A.K.; Kubo, H.; Marino, A.D.; Matsuoka, K.; Murakami, A.; Nakaya, T.; Suzuki, K.; Yuan, T.; Zimmerman, E.D.

2013-01-01

The T2K long-baseline neutrino oscillation experiment in Japan needs precise predictions of the initial neutrino flux. The highest precision can be reached based on detailed measurements of hadron emission from the same target as used by T2K exposed to a proton beam of the same kinetic energy of 30 GeV. The corresponding data were recorded in 2007-2010 by the NA61/SHINE experiment at the CERN SPS using a replica of the T2K graphite target. In this paper details of the experiment, data taking, data analysis method and results from the 2007 pilot run are presented. Furthermore, the application of the NA61/SHINE measurements to the predictions of the T2K initial neutrino flux is described and discussed.

Methods of dealing with co-products of biofuels in life-cycle analysis and consequent results within the U.S. context

International Nuclear Information System (INIS)

Wang, Michael; Huo Hong; Arora, Salil

2011-01-01

Products other than biofuels are produced in biofuel plants. For example, corn ethanol plants produce distillers' grains and solubles. Soybean crushing plants produce soy meal and soy oil, which is used for biodiesel production. Electricity is generated in sugarcane ethanol plants both for internal consumption and export to the electric grid. Future cellulosic ethanol plants could be designed to co-produce electricity with ethanol. It is important to take co-products into account in the life-cycle analysis of biofuels and several methods are available to do so. Although the International Standard Organization's ISO 14040 advocates the system boundary expansion method (also known as the 'displacement method' or the 'substitution method') for life-cycle analyses, application of the method has been limited because of the difficulty in identifying and quantifying potential products to be displaced by biofuel co-products. As a result, some LCA studies and policy-making processes have considered alternative methods. In this paper, we examine the available methods to deal with biofuel co-products, explore the strengths and weaknesses of each method, and present biofuel LCA results with different co-product methods within the U.S. context.

Methods of dealing with co-products of biofuels in life-cycle analysis and consequent results within the U.S. context

Energy Technology Data Exchange (ETDEWEB)

Wang, Michael, E-mail: mqwang@anl.gov [Center for Transportation Research, Argonne National Laboratory, Argonne, IL 60439 (United States); Huo Hong [Institute of Energy, Environment, and Economics, Tsinghua University, Beijing, 100084 (China); Arora, Salil [Center for Transportation Research, Argonne National Laboratory, Argonne, IL 60439 (United States)

2011-10-15

Products other than biofuels are produced in biofuel plants. For example, corn ethanol plants produce distillers' grains and solubles. Soybean crushing plants produce soy meal and soy oil, which is used for biodiesel production. Electricity is generated in sugarcane ethanol plants both for internal consumption and export to the electric grid. Future cellulosic ethanol plants could be designed to co-produce electricity with ethanol. It is important to take co-products into account in the life-cycle analysis of biofuels and several methods are available to do so. Although the International Standard Organization's ISO 14040 advocates the system boundary expansion method (also known as the 'displacement method' or the 'substitution method') for life-cycle analyses, application of the method has been limited because of the difficulty in identifying and quantifying potential products to be displaced by biofuel co-products. As a result, some LCA studies and policy-making processes have considered alternative methods. In this paper, we examine the available methods to deal with biofuel co-products, explore the strengths and weaknesses of each method, and present biofuel LCA results with different co-product methods within the U.S. context.

Energy Conservation Program Evaluation : Practical Methods, Useful Results : Proceedings of the 1987 Conference.

Energy Technology Data Exchange (ETDEWEB)

Argonne National Laboratory; International Conference on Energy Conservation Program Evaluation (3rd : 1987 : Chicago, ILL.)

1987-01-01

The success of cutting-edge evaluation methodologies depends on our ability to merge, manage, and maintain huge amounts of data. Equally important is presenting results of the subsequent analysis in a meaningful way. These topics are addressed at this session. The considerable amounts of data that have been collected about energy conservation programs are rarely used by other researchers, either because they are not available in computerized form or, if they are, because of the difficulties of interpreting someone else's data, format inconsistencies, incompatibility of computers, lack of documentation, data entry errors, and obtaining data use agreements. Even census, RECS, and AHS data can be best used only by a researcher who is intimately familiar with them. Once the data have been accessed and analyzed, the results need to be put in a format that can be readily understood by others. This is a particularly difficult task when submetered data is the basis of the analysis. Stoops and Gilbride will demonstrate their methods of using off-the-shelf graphics software to illustrate complex hourly data from nonresidential buildings.

The Quadrumafios electron cyclotron resonance ion source: presentation and analysis of the results

International Nuclear Information System (INIS)

Girard, A.; Briand, P.; Gaudart, G.; Klein, J.P.; Bourg, F.; Debernardi, J.; Mathonnet, J.M.; Melin, G.; Su, Y.

1993-01-01

The Quadrumafios electron cyclotron resonance ion source (ECRIS) has been especially designed to permit physical studies of the plasma; this paper describes the source itself (which has been operated at 10 GHz in a first step), its preliminary performances, and the different diagnostics involved, which mainly concern the electron population (ECE, X rays, diamagnetism, microwave interferometer, and electron analyser). The results are presented and discussed: there is of course a close relationship between the parameters of the plasma and the performances of the source; this point will be discussed in the article. (authors). 5 refs., 9 figs

Communicating clinical trial outcomes: Effects of presentation method on physicians' evaluations of new treatments

Directory of Open Access Journals (Sweden)

Francesco Marcatto

2013-01-01

Full Text Available Physicians expect a treatment to be more effective when its clinical outcomes are described as relative rather than as absolute risk reductions. We examined whether effects of presentation method (relative vs. absolute risk reduction remain when physicians are provided the baseline risk information, a vital piece of statistical information omitted in previous studies. Using a between-subjects design, ninety five physicians were presented the risk reduction associated with a fictitious treatment for hypertension either as an absolute risk reduction or as a relative risk reduction, with or without including baseline risk information. Physicians reported that the treatment would be more effective and that they would be more willing to prescribe it when its risk reduction was presented to them in relative rather than in absolute terms. The relative risk reduction was perceived as more effective than absolute risk reduction even when the baseline risk information was explicitly reported. We recommend that information about absolute risk reduction be made available to physicians in the reporting of clinical outcomes. Moreover, health professionals should be cognizant of the potential biasing effects of risk information presented in relative risk terms.

Why do children present to emergency departments? Exploring motivators and measures of presentation appropriateness for children presenting to a paediatric emergency department.

Science.gov (United States)

Cheek, John A; Braitberg, George; Craig, Simon; West, Adam

2017-05-01

To compare the parental motivators and referring general practitioner's (GP's) reasons for advising emergency department (ED) attendance with the assessment of ED medical staff. To compare ED clinician opinion with other published methods that have attempted to define 'primary care suitable' presentations to the ED. A prospective observational study and series of surveys regarding the attendance of children presenting to a single tertiary paediatric ED. Surveys were distributed to the treating ED clinician, the child's parent/guardian, and the referring GP. Results between the three groups were analysed and compared. There were a total of 1069 presentations during the study period. Six hundred (58.4%, 95% CI 55.3-61.4%) presentations were judged as 'ED appropriate' by the treating ED clinician. When compared with methods used to retrospectively judge whether ED patients are considered 'primary care suitable', ED clinicians disagree between 22.4 and 38.8% of the time. For patients who presented directly to ED, 85.6% did so for a medical reason, whilst 32.1% did so for a GP access reason. Being referred by a GP improved the ED clinicians' opinion of the appropriateness of the presentation (49.2 vs. 73.9%, P motivators that drive this behaviour is needed. We believe the solution to increasing utilisation of EDs by children must be a balanced approach that addresses community expectations and appropriately resources EDs. © 2017 Paediatrics and Child Health Division (The Royal Australasian College of Physicians).

Interpreting Statistical Significance Test Results: A Proposed New "What If" Method.

Science.gov (United States)

Kieffer, Kevin M.; Thompson, Bruce

As the 1994 publication manual of the American Psychological Association emphasized, "p" values are affected by sample size. As a result, it can be helpful to interpret the results of statistical significant tests in a sample size context by conducting so-called "what if" analyses. However, these methods can be inaccurate…

Presentation of a semiempirical method for the calculation of doses due to neutrons and capture gamma rays inside high energy accelerators rooms

International Nuclear Information System (INIS)

Larcher, A.M.; Bonet Duran, S.M.

1998-01-01

Full text: Medical electron accelerators operating above 10 MeV produce radiation beams that are contaminated with neutrons. Therefore, shielding design for high energy accelerator rooms must consider the neutron component of the radiation field. In this paper a semiempirical method is presented to calculate doses due to neutrons and capture gamma rays inside the room and the maze. The calculation method is based on the knowledge of the neutron yield Q (neutrons/Gy of photons at isocenter) and the average energy of the primary beam of neutrons Eo (MeV). The method constitutes an appropriate tool for shielding facilities evaluation. The accuracy of the method has been contrasted with data obtained from the literature and an excellent correlation among the calculations and the measured values was achieved. In addition, the method has been used in the verification of experimental data corresponding to a 15 MeV linear accelerator installed in the country with similar results. (author) [es

Impact of Costing and Cost Analysis Methods on the Result of the Period: Methods Based on Full Cost Theory

Directory of Open Access Journals (Sweden)

Toma Maria

2017-01-01

In light of the above, in the present paper we have proposed that objectives, to approach the methods of calculating full costs (economic or traditional, and comparing them to determine the effect they have on the outcome of the period.

The albatross plot: A novel graphical tool for presenting results of diversely reported studies in a systematic review.

Science.gov (United States)

Harrison, Sean; Jones, Hayley E; Martin, Richard M; Lewis, Sarah J; Higgins, Julian P T

2017-09-01

Meta-analyses combine the results of multiple studies of a common question. Approaches based on effect size estimates from each study are generally regarded as the most informative. However, these methods can only be used if comparable effect sizes can be computed from each study, and this may not be the case due to variation in how the studies were done or limitations in how their results were reported. Other methods, such as vote counting, are then used to summarize the results of these studies, but most of these methods are limited in that they do not provide any indication of the magnitude of effect. We propose a novel plot, the albatross plot, which requires only a 1-sided P value and a total sample size from each study (or equivalently a 2-sided P value, direction of effect and total sample size). The plot allows an approximate examination of underlying effect sizes and the potential to identify sources of heterogeneity across studies. This is achieved by drawing contours showing the range of effect sizes that might lead to each P value for given sample sizes, under simple study designs. We provide examples of albatross plots using data from previous meta-analyses, allowing for comparison of results, and an example from when a meta-analysis was not possible. Copyright © 2017 The Authors. Research Synthesis Methods Published by John Wiley & Sons Ltd.

Prolactinomas may have unusual presentations resulting from massive extrasellar tumor extension

Directory of Open Access Journals (Sweden)

Marise Ribeiro de Sousa Berriel

2016-07-01

Full Text Available ABSTRACT The purpose of this case series is to report eight patients with giant prolactinomas emphasizing presentations and a treatment complication. The study group included six men and two women. The median age was 29 years (18–54 years; median serum prolactin level was 4,562 ng/ml (1,543–18,690 ng/ml; three patients (37.5% had panhypopituitarism; median tumor diameter was 50 mm (41–60 mm. Five patients (62.5% had visual field defects and three had improvement during treatment; six patients (75% reached prolactin normalization, with a median time of 10.5 months (7–84 months and median dose of 2.0 mg/week (1.0 to 3.0 mg/week. One patient presented as a true incidentaloma. One patient presented a cerebrospinal fluid leakage during medical treatment and refused surgery, however this resolved with conservative measures. This case series illustrate a rare subtype of macroprolactinomas, the importance of considering unusual presentations at the diagnosis, the effectiveness of pharmacological treatment and its possible complications.

Deterministic methods in radiation transport. A compilation of papers presented February 4--5, 1992

Energy Technology Data Exchange (ETDEWEB)

Rice, A.F.; Roussin, R.W. [eds.

1992-06-01

The Seminar on Deterministic Methods in Radiation Transport was held February 4--5, 1992, in Oak Ridge, Tennessee. Eleven presentations were made and the full papers are published in this report, along with three that were submitted but not given orally. These papers represent a good overview of the state of the art in the deterministic solution of radiation transport problems for a variety of applications of current interest to the Radiation Shielding Information Center user community.

Deterministic methods in radiation transport. A compilation of papers presented February 4-5, 1992

Energy Technology Data Exchange (ETDEWEB)

Rice, A. F.; Roussin, R. W. [eds.

1992-06-01

The Seminar on Deterministic Methods in Radiation Transport was held February 4--5, 1992, in Oak Ridge, Tennessee. Eleven presentations were made and the full papers are published in this report, along with three that were submitted but not given orally. These papers represent a good overview of the state of the art in the deterministic solution of radiation transport problems for a variety of applications of current interest to the Radiation Shielding Information Center user community.

A method for data handling numerical results in parallel OpenFOAM simulations

International Nuclear Information System (INIS)

nd Vasile Pârvan Ave., 300223, TM Timişoara, Romania, alin.anton@cs.upt.ro (Romania))" data-affiliation=" (Faculty of Automatic Control and Computing, Politehnica University of Timişoara, 2nd Vasile Pârvan Ave., 300223, TM Timişoara, Romania, alin.anton@cs.upt.ro (Romania))" >Anton, Alin; th Mihai Viteazu Ave., 300221, TM Timişoara (Romania))" data-affiliation=" (Center for Advanced Research in Engineering Science, Romanian Academy – Timişoara Branch, 24th Mihai Viteazu Ave., 300221, TM Timişoara (Romania))" >Muntean, Sebastian

2015-01-01

Parallel computational fluid dynamics simulations produce vast amount of numerical result data. This paper introduces a method for reducing the size of the data by replaying the interprocessor traffic. The results are recovered only in certain regions of interest configured by the user. A known test case is used for several mesh partitioning scenarios using the OpenFOAM toolkit ® [1]. The space savings obtained with classic algorithms remain constant for more than 60 Gb of floating point data. Our method is most efficient on large simulation meshes and is much better suited for compressing large scale simulation results than the regular algorithms

A method for data handling numerical results in parallel OpenFOAM simulations

Energy Technology Data Exchange (ETDEWEB)

Anton, Alin [Faculty of Automatic Control and Computing, Politehnica University of Timişoara, 2" n" d Vasile Pârvan Ave., 300223, TM Timişoara, Romania, alin.anton@cs.upt.ro (Romania); Muntean, Sebastian [Center for Advanced Research in Engineering Science, Romanian Academy – Timişoara Branch, 24" t" h Mihai Viteazu Ave., 300221, TM Timişoara (Romania)

2015-12-31

Parallel computational fluid dynamics simulations produce vast amount of numerical result data. This paper introduces a method for reducing the size of the data by replaying the interprocessor traffic. The results are recovered only in certain regions of interest configured by the user. A known test case is used for several mesh partitioning scenarios using the OpenFOAM toolkit{sup ®}[1]. The space savings obtained with classic algorithms remain constant for more than 60 Gb of floating point data. Our method is most efficient on large simulation meshes and is much better suited for compressing large scale simulation results than the regular algorithms.

A Review of Spectral Methods for Variable Amplitude Fatigue Prediction and New Results

Science.gov (United States)

Larsen, Curtis E.; Irvine, Tom

2013-01-01

A comprehensive review of the available methods for estimating fatigue damage from variable amplitude loading is presented. The dependence of fatigue damage accumulation on power spectral density (psd) is investigated for random processes relevant to real structures such as in offshore or aerospace applications. Beginning with the Rayleigh (or narrow band) approximation, attempts at improved approximations or corrections to the Rayleigh approximation are examined by comparison to rainflow analysis of time histories simulated from psd functions representative of simple theoretical and real world applications. Spectral methods investigated include corrections by Wirsching and Light, Ortiz and Chen, the Dirlik formula, and the Single-Moment method, among other more recent proposed methods. Good agreement is obtained between the spectral methods and the time-domain rainflow identification for most cases, with some limitations. Guidelines are given for using the several spectral methods to increase confidence in the damage estimate.

Linear regression metamodeling as a tool to summarize and present simulation model results.

Science.gov (United States)

Jalal, Hawre; Dowd, Bryan; Sainfort, François; Kuntz, Karen M

2013-10-01

Modelers lack a tool to systematically and clearly present complex model results, including those from sensitivity analyses. The objective was to propose linear regression metamodeling as a tool to increase transparency of decision analytic models and better communicate their results. We used a simplified cancer cure model to demonstrate our approach. The model computed the lifetime cost and benefit of 3 treatment options for cancer patients. We simulated 10,000 cohorts in a probabilistic sensitivity analysis (PSA) and regressed the model outcomes on the standardized input parameter values in a set of regression analyses. We used the regression coefficients to describe measures of sensitivity analyses, including threshold and parameter sensitivity analyses. We also compared the results of the PSA to deterministic full-factorial and one-factor-at-a-time designs. The regression intercept represented the estimated base-case outcome, and the other coefficients described the relative parameter uncertainty in the model. We defined simple relationships that compute the average and incremental net benefit of each intervention. Metamodeling produced outputs similar to traditional deterministic 1-way or 2-way sensitivity analyses but was more reliable since it used all parameter values. Linear regression metamodeling is a simple, yet powerful, tool that can assist modelers in communicating model characteristics and sensitivity analyses.

Current advances on polynomial resultant formulations

Science.gov (United States)

Sulaiman, Surajo; Aris, Nor'aini; Ahmad, Shamsatun Nahar

2017-08-01

Availability of computer algebra systems (CAS) lead to the resurrection of the resultant method for eliminating one or more variables from the polynomials system. The resultant matrix method has advantages over the Groebner basis and Ritt-Wu method due to their high complexity and storage requirement. This paper focuses on the current resultant matrix formulations and investigates their ability or otherwise towards producing optimal resultant matrices. A determinantal formula that gives exact resultant or a formulation that can minimize the presence of extraneous factors in the resultant formulation is often sought for when certain conditions that it exists can be determined. We present some applications of elimination theory via resultant formulations and examples are given to explain each of the presented settings.

Quantifying the measurement uncertainty of results from environmental analytical methods.

Science.gov (United States)

Moser, J; Wegscheider, W; Sperka-Gottlieb, C

2001-07-01

The Eurachem-CITAC Guide Quantifying Uncertainty in Analytical Measurement was put into practice in a public laboratory devoted to environmental analytical measurements. In doing so due regard was given to the provisions of ISO 17025 and an attempt was made to base the entire estimation of measurement uncertainty on available data from the literature or from previously performed validation studies. Most environmental analytical procedures laid down in national or international standards are the result of cooperative efforts and put into effect as part of a compromise between all parties involved, public and private, that also encompasses environmental standards and statutory limits. Central to many procedures is the focus on the measurement of environmental effects rather than on individual chemical species. In this situation it is particularly important to understand the measurement process well enough to produce a realistic uncertainty statement. Environmental analytical methods will be examined as far as necessary, but reference will also be made to analytical methods in general and to physical measurement methods where appropriate. This paper describes ways and means of quantifying uncertainty for frequently practised methods of environmental analysis. It will be shown that operationally defined measurands are no obstacle to the estimation process as described in the Eurachem/CITAC Guide if it is accepted that the dominating component of uncertainty comes from the actual practice of the method as a reproducibility standard deviation.

Investigation of error estimation method of observational data and comparison method between numerical and observational results toward V and V of seismic simulation

International Nuclear Information System (INIS)

Suzuki, Yoshio; Kawakami, Yoshiaki; Nakajima, Norihiro

2017-01-01

The method to estimate errors included in observational data and the method to compare numerical results with observational results are investigated toward the verification and validation (V and V) of a seismic simulation. For the method to estimate errors, 144 literatures for the past 5 years (from the year 2010 to 2014) in the structure engineering field and earthquake engineering field where the description about acceleration data is frequent are surveyed. As a result, it is found that some processes to remove components regarded as errors from observational data are used in about 30% of those literatures. Errors are caused by the resolution, the linearity, the temperature coefficient for sensitivity, the temperature coefficient for zero shift, the transverse sensitivity, the seismometer property, the aliasing, and so on. Those processes can be exploited to estimate errors individually. For the method to compare numerical results with observational results, public materials of ASME V and V Symposium 2012-2015, their references, and above 144 literatures are surveyed. As a result, it is found that six methods have been mainly proposed in existing researches. Evaluating those methods using nine items, advantages and disadvantages for those methods are arranged. The method is not well established so that it is necessary to employ those methods by compensating disadvantages and/or to search for a solution to a novel method. (author)

Nuclear magnetic resonance. Present results and its application to renal pathology. Experimental study of hydronephrosis

International Nuclear Information System (INIS)

Bertrand, P.

1987-01-01

Results of proton nuclear magnetic resonance imaging and relaxation time measurement of experimental hydronephrosis in mice are presented. The study is preceded by a description of the physical principles underlying the phenomenon of nuclear magnetic resonance and of its biomedical applications and with a review of the clinical use of NMR imaging in renal pathology [fr

Presenting a mapping method based on fuzzy Logic and TOPSIS multi criteria decision-making methods to detect promising porphyry copper mineralization areas in the east of the Sarcheshmeh copper metallogenic district

Directory of Open Access Journals (Sweden)

Shokouh Riahi

2017-11-01

Full Text Available Introduction The growing demand for base metals such as iron, copper, lead and zinc on the one hand and the diminishing of surficial and shallow resources of these elements on the other hand have forced explorationists to focus on detecting deep deposits of these metals. As a result, the discovery of such deep deposits requires more advanced and sophisticated methods in the course of preliminary prospecting stages. Since the discovery of new deposits is getting to be increasingly difficult, deploying new prospecting technologies that employ more deposit attributes in the course of combining exploratory evidence may reduce the exploration costs with lower uncertainties. In the past two decades, a number of new data mining and integrating approaches capable of incorporating direct and indirect mineralization indicators, based on expert knowledge, data, or a combination of both, have been proposed Bonham-Carter, 1994(. In the first step, the input exploratory data layers are corrected and validated through applying some statistical pre-processing algorithms such as background and outlier removal methods. In order to detect a mineralization occurrence, it is necessary to find the proper exploratory geological, geochemical and geophysical data layers which have direct or indirect associations with the governing mineralization followed by constructing these models in an appropriate GIS platform (Malkzewski, 1999. Due to the imperfect available data and a number of unknown parameters affecting the mineralization process, the application of conventional GIS integration methods such as Boolean or weighted overlay or even fuzzy logic methods alone may not produce appropriate results, pointing to a need for deploying multi-criteria decision-making methods such as TOPSIS. In the present study, the pre-processed exploratory data including geological, remotely sensed geophysical and geochemical imagery were used to detect favorable mineralization zones

The Effects of Presentation Method and Information Density on Visual Search Ability and Working Memory Load

Science.gov (United States)

Chang, Ting-Wen; Kinshuk; Chen, Nian-Shing; Yu, Pao-Ta

2012-01-01

This study investigates the effects of successive and simultaneous information presentation methods on learner's visual search ability and working memory load for different information densities. Since the processing of information in the brain depends on the capacity of visual short-term memory (VSTM), the limited information processing capacity…

[The long-term results of the application of the combined rehabilitative treatment in the patients presenting with knee osteoarthrosis].

Science.gov (United States)

Razumov, A N; Purigа, A O; Yurova, O V

2015-01-01

The rehabilitative treatment of the patients suffering from knee osteoarthrosis (OA) up-to-date remains one of the most important medical and social problems of modern medicine due to the high prevalence of this disease, heavy morbidity, and the significant deterioration of the quality of the patients' life. The objective of the present study was to evaluate the long-term results of the combined application of radon and extracorporeal shock-wave therapy for the rehabilitation of the patients presenting with knee OA. The study involved 75 patients at the age from 35 to 62 years with the confirmed diagnosis of stage II and III knee osteoarthrosis. They were divided into 3 groups. Those comprising the main group received extracorporeal shock-wave therapy in combination with the treatment based on the use of radon baths. The patients included in the group of comparison were given a course of radon therapy alone while the patients of the control group received the standard treatment including physiotherapy, magnetic therapy, and the use of non-steroidal anti-inflammatory drugs (NSAIDs). The study has demonstrated the high effectiveness of the combined application of the radon baths and extracorporeal shock-wave therapy that was manifested as the substantial decrease of pain intensity, the increased range of motion in the knee joints, and the improvement of the general quality of life. These beneficial effects persisted during a period of up to 12 months. The stable remission was documented in 82% of the patients comprising the main group. The data obtained give reason to recommend the method employed in the present study for the extensive practical application at different stages of medical rehabilitation of the patients presenting with knee osteoarthrosis.

Image restoration by the method of convex projections: part 2 applications and numerical results.

Science.gov (United States)

Sezan, M I; Stark, H

1982-01-01

The image restoration theory discussed in a previous paper by Youla and Webb [1] is applied to a simulated image and the results compared with the well-known method known as the Gerchberg-Papoulis algorithm. The results show that the method of image restoration by projection onto convex sets, by providing a convenient technique for utilizing a priori information, performs significantly better than the Gerchberg-Papoulis method.

Impact of Costing and Cost Analysis Methods on the Result of the Period: Methods Based on Partial Cost Theory

Directory of Open Access Journals (Sweden)

Toma Maria

2017-01-01

Looking from this perspective, in the present paper we have proposed that objectives, to approach the full cost calculation methods based on partial costs (direct-costing on the product or direct-costing evolved, and comparing them to determine the effect they have on the outcome of the period.

Using a Regression Method for Estimating Performance in a Rapid Serial Visual Presentation Target-Detection Task

Science.gov (United States)

2017-12-01

Fig. 2 Simulation method; the process for one iteration of the simulation . It was repeated 250 times per combination of HR and FAR. Analysis was...distribution is unlimited. 8 Fig. 2 Simulation method; the process for one iteration of the simulation . It was repeated 250 times per combination of HR...stimuli. Simulations show that this regression method results in an unbiased and accurate estimate of target detection performance. The regression

A method for modeling laterally asymmetric proton beamlets resulting from collimation

Energy Technology Data Exchange (ETDEWEB)

Gelover, Edgar; Wang, Dongxu; Flynn, Ryan T.; Hyer, Daniel E. [Department of Radiation Oncology, University of Iowa, 200 Hawkins Drive, Iowa City, Iowa 52242 (United States); Hill, Patrick M. [Department of Human Oncology, University of Wisconsin, 600 Highland Avenue, Madison, Wisconsin 53792 (United States); Gao, Mingcheng; Laub, Steve; Pankuch, Mark [Division of Medical Physics, CDH Proton Center, 4455 Weaver Parkway, Warrenville, Illinois 60555 (United States)

2015-03-15

Purpose: To introduce a method to model the 3D dose distribution of laterally asymmetric proton beamlets resulting from collimation. The model enables rapid beamlet calculation for spot scanning (SS) delivery using a novel penumbra-reducing dynamic collimation system (DCS) with two pairs of trimmers oriented perpendicular to each other. Methods: Trimmed beamlet dose distributions in water were simulated with MCNPX and the collimating effects noted in the simulations were validated by experimental measurement. The simulated beamlets were modeled analytically using integral depth dose curves along with an asymmetric Gaussian function to represent fluence in the beam’s eye view (BEV). The BEV parameters consisted of Gaussian standard deviations (sigmas) along each primary axis (σ{sub x1},σ{sub x2},σ{sub y1},σ{sub y2}) together with the spatial location of the maximum dose (μ{sub x},μ{sub y}). Percent depth dose variation with trimmer position was accounted for with a depth-dependent correction function. Beamlet growth with depth was accounted for by combining the in-air divergence with Hong’s fit of the Highland approximation along each axis in the BEV. Results: The beamlet model showed excellent agreement with the Monte Carlo simulation data used as a benchmark. The overall passing rate for a 3D gamma test with 3%/3 mm passing criteria was 96.1% between the analytical model and Monte Carlo data in an example treatment plan. Conclusions: The analytical model is capable of accurately representing individual asymmetric beamlets resulting from use of the DCS. This method enables integration of the DCS into a treatment planning system to perform dose computation in patient datasets. The method could be generalized for use with any SS collimation system in which blades, leaves, or trimmers are used to laterally sharpen beamlets.

A method for modeling laterally asymmetric proton beamlets resulting from collimation

International Nuclear Information System (INIS)

Gelover, Edgar; Wang, Dongxu; Flynn, Ryan T.; Hyer, Daniel E.; Hill, Patrick M.; Gao, Mingcheng; Laub, Steve; Pankuch, Mark

2015-01-01

Purpose: To introduce a method to model the 3D dose distribution of laterally asymmetric proton beamlets resulting from collimation. The model enables rapid beamlet calculation for spot scanning (SS) delivery using a novel penumbra-reducing dynamic collimation system (DCS) with two pairs of trimmers oriented perpendicular to each other. Methods: Trimmed beamlet dose distributions in water were simulated with MCNPX and the collimating effects noted in the simulations were validated by experimental measurement. The simulated beamlets were modeled analytically using integral depth dose curves along with an asymmetric Gaussian function to represent fluence in the beam’s eye view (BEV). The BEV parameters consisted of Gaussian standard deviations (sigmas) along each primary axis (σ x1 ,σ x2 ,σ y1 ,σ y2 ) together with the spatial location of the maximum dose (μ x ,μ y ). Percent depth dose variation with trimmer position was accounted for with a depth-dependent correction function. Beamlet growth with depth was accounted for by combining the in-air divergence with Hong’s fit of the Highland approximation along each axis in the BEV. Results: The beamlet model showed excellent agreement with the Monte Carlo simulation data used as a benchmark. The overall passing rate for a 3D gamma test with 3%/3 mm passing criteria was 96.1% between the analytical model and Monte Carlo data in an example treatment plan. Conclusions: The analytical model is capable of accurately representing individual asymmetric beamlets resulting from use of the DCS. This method enables integration of the DCS into a treatment planning system to perform dose computation in patient datasets. The method could be generalized for use with any SS collimation system in which blades, leaves, or trimmers are used to laterally sharpen beamlets

A method for modeling laterally asymmetric proton beamlets resulting from collimation

Science.gov (United States)

Gelover, Edgar; Wang, Dongxu; Hill, Patrick M.; Flynn, Ryan T.; Gao, Mingcheng; Laub, Steve; Pankuch, Mark; Hyer, Daniel E.

2015-01-01

Purpose: To introduce a method to model the 3D dose distribution of laterally asymmetric proton beamlets resulting from collimation. The model enables rapid beamlet calculation for spot scanning (SS) delivery using a novel penumbra-reducing dynamic collimation system (DCS) with two pairs of trimmers oriented perpendicular to each other. Methods: Trimmed beamlet dose distributions in water were simulated with MCNPX and the collimating effects noted in the simulations were validated by experimental measurement. The simulated beamlets were modeled analytically using integral depth dose curves along with an asymmetric Gaussian function to represent fluence in the beam’s eye view (BEV). The BEV parameters consisted of Gaussian standard deviations (sigmas) along each primary axis (σx1,σx2,σy1,σy2) together with the spatial location of the maximum dose (μx,μy). Percent depth dose variation with trimmer position was accounted for with a depth-dependent correction function. Beamlet growth with depth was accounted for by combining the in-air divergence with Hong’s fit of the Highland approximation along each axis in the BEV. Results: The beamlet model showed excellent agreement with the Monte Carlo simulation data used as a benchmark. The overall passing rate for a 3D gamma test with 3%/3 mm passing criteria was 96.1% between the analytical model and Monte Carlo data in an example treatment plan. Conclusions: The analytical model is capable of accurately representing individual asymmetric beamlets resulting from use of the DCS. This method enables integration of the DCS into a treatment planning system to perform dose computation in patient datasets. The method could be generalized for use with any SS collimation system in which blades, leaves, or trimmers are used to laterally sharpen beamlets. PMID:25735287

Cycom 977-2 Composite Material: Impact Test Results (workshop presentation)

Science.gov (United States)

Engle, Carl; Herald, Stephen; Watkins, Casey

2005-01-01

Contents include the following: Ambient (13A) tests of Cycom 977-2 impact characteristics by the Brucenton and statistical method at MSFC and WSTF. Repeat (13A) tests of tested Cycom from phase I at MSFC to expended testing statistical database. Conduct high-pressure tests (13B) in liquid oxygen (LOX) and GOX at MSFC and WSTF to determine Cycom reaction characteristics and batch effect. Conduct expended ambient (13A) LOX test at MSFC and high-pressure (13B) testing to determine pressure effects in LOX. Expend 13B GOX database.

[Adverse events management. Methods and results of a development project].

Science.gov (United States)

Rabøl, Louise Isager; Jensen, Elisabeth Brøgger; Hellebek, Annemarie H; Pedersen, Beth Lilja

2006-11-27

This article describes the methods and results of a project in the Copenhagen Hospital Corporation (H:S) on preventing adverse events. The aim of the project was to raise awareness about patients' safety, test a reporting system for adverse events, develop and test methods of analysis of events and propagate ideas about how to prevent adverse events. H:S developed an action plan and a reporting system for adverse events, founded an organization and developed an educational program on theories and methods of learning from adverse events for both leaders and employees. During the three-year period from 1 January 2002 to 31 December 2004, the H:S staff reported 6011 adverse events. In the same period, the organization completed 92 root cause analyses. More than half of these dealt with events that had been optional to report, the other half events that had been mandatory to report. The number of reports and the front-line staff's attitude towards reporting shows that the H:S succeeded in founding a safety culture. Future work should be centred on developing and testing methods that will prevent adverse events from happening. The objective is to suggest and complete preventive initiatives which will help increase patient safety.

Some elaborating methods of gamma scanning results on irradiated nuclear fuels

International Nuclear Information System (INIS)

Sternini, E.

1979-01-01

Gamma scanning, as a post-irradiation examination, is a technique which provides a large number of informations on irradiated nuclear fuels. Power profile, fission products distribution, average and local burn-up of single elements structural and nuclear behaviour of fuel materials are examples of the obtained informations. In the present work experimental methods and theoretical calculations used at the CNEN hot cell laboratory for the mentioned purposes are described. Errors arising from the application of the gamma scanning technique are also discussed

International Workshop on Exotic Hadronic Atoms, Deeply Bound Kaonic Nuclear States and Antihydrogen : Present Results, Future Challenges

CERN Document Server

Widmann, E; Curceanu, C; Trento 2006; Trento06

2006-01-01

These are the miniproceedings of the workshop "Exotic hadronic atoms, deeply bound kaonic nuclear states and antihydrogen: present results, future challenges," which was held at the European Centre for Theoretical Nuclear Physics and Related Studies (ECT*), Trento (Italy), June 19-24, 2006. The document includes a short presentation of the topics, the list of participants, and a short contribution from each speaker.

MLFMA-accelerated Nyström method for ultrasonic scattering - Numerical results and experimental validation

Science.gov (United States)

Gurrala, Praveen; Downs, Andrew; Chen, Kun; Song, Jiming; Roberts, Ron

2018-04-01

Full wave scattering models for ultrasonic waves are necessary for the accurate prediction of voltage signals received from complex defects/flaws in practical nondestructive evaluation (NDE) measurements. We propose the high-order Nyström method accelerated by the multilevel fast multipole algorithm (MLFMA) as an improvement to the state-of-the-art full-wave scattering models that are based on boundary integral equations. We present numerical results demonstrating improvements in simulation time and memory requirement. Particularly, we demonstrate the need for higher order geom-etry and field approximation in modeling NDE measurements. Also, we illustrate the importance of full-wave scattering models using experimental pulse-echo data from a spherical inclusion in a solid, which cannot be modeled accurately by approximation-based scattering models such as the Kirchhoff approximation.

Patients' Experiences of Cancer Diagnosis as a Result of an Emergency Presentation: A Qualitative Study.

Science.gov (United States)

Black, Georgia; Sheringham, Jessica; Spencer-Hughes, Vicki; Ridge, Melanie; Lyons, Mairead; Williams, Charlotte; Fulop, Naomi; Pritchard-Jones, Kathy

2015-01-01

Cancers diagnosed following visits to emergency departments (ED) or emergency admissions (emergency presentations) are associated with poor survival and may result from preventable diagnostic delay. To improve outcomes for these patients, a better understanding is needed about how emergency presentations arise. This study sought to capture patients' experiences of this diagnostic pathway in the English NHS. Eligible patients were identified in a service evaluation of emergency presentations and invited to participate. Interviews, using an open-ended biographical structure, captured participants' experiences of healthcare services before diagnosis and were analysed thematically, informed by the Walter model of Pathways to Treatment and NICE guidance in an iterative process. Twenty-seven interviews were conducted. Three typologies were identified: A: Rapid investigation and diagnosis, and B: Repeated cycles of healthcare seeking and appraisal without resolution, with two variants where B1 appears consistent with guidance and B2 has evidence that management was not consistent with guidance. Most patients' (23/27) experiences fitted types B1 and B2. Potentially avoidable breakdowns in diagnostic pathways caused delays when patients were conflicted by escalating symptoms and a benign diagnosis given earlier by doctors. ED was sometimes used as a conduit to rapid testing by primary care clinicians, although this pathway was not always successful. This study draws on patients' experiences of their diagnosis to provide novel insights into how emergency presentations arise. Through these typologies, we show that the typical experience of patients diagnosed through an emergency presentation diverges significantly from normative pathways even when there is no evidence of serious service failures. Consultations were not a conduit to diagnosis when they inhibited patients' capacity to appraise their own symptoms appropriately and when they resulted in a reluctance to seek

Synthesis of present methods of surface contamination detection (skin, clothes, laboratories)

International Nuclear Information System (INIS)

Joudrier, P.

1983-01-01

The signification of the term ''contamination'' is briefly recalled. To measure the levels of contamination, there are only two methods: the direct method and the indirect method. Finally, the recent improvements in the surface contamination detection field are shortly reviewed [fr

The WELSONS experiment: overview and presentation of first results on the surface atmospheric boundary-layer in semiarid Spain

Directory of Open Access Journals (Sweden)

J.-P. Frangi

Full Text Available This study presents the preliminary results of the local energy budget and dynamic characteristics of the surface atmospheric boundary-layer (SBL during the WELSONS (wind erosion and losses of soil nutrients in semiarid Spain experiment. Some Mediterranean regions suffer land degradation by wind erosion as a consequence of their particular soil and climate conditions and inappropriate agricultural practice. In Spain, where land degradation by water erosion is well known, the lack of field studies to quantify soils losses by wind erosion resulted in the European Community organizing a scientific program for this specific issue. The European programme known as WELSONS was devoted to study the wind erosion process in central Aragon (NE Spain. This multidisciplinary experiment, which began in 1996 and finished in 1998, was carried out over an agricultural soil which was left fallow. Within the experimental field, two plots were delimited where two tillage treatments were applied, a mould-board ploughing (or conventional tillage denoted CT and chisel ploughing (reduced tillage denoted RT. This was to study on bare soil the influence of tillage method on surface conditions, saltation flux, vertical dust flux, erosion rates, dynamics characteristics such as friction velocity, roughness length, etc., and energy budget. The partitioning of the available energy, resulting from the dynamics of the SBL, are quite different over the two plots because of their own peculiar soil and surface properties. The first results show that the RT treatment seems to provide a wind erosion protection. Because of the long data recording time and particular phenomena (formation of a crust at the soil surface, very dry conditions, high wind speed for instance, these microclimatological data acquired during the WELSONS programmes may be helpful to test atmospheric boundary-layer models coupled with soil models.

Key words: Hydrology (desertification - Meterology and

The WELSONS experiment: overview and presentation of first results on the surface atmospheric boundary-layer in semiarid Spain

Directory of Open Access Journals (Sweden)

J.-P. Frangi

2000-03-01

Full Text Available This study presents the preliminary results of the local energy budget and dynamic characteristics of the surface atmospheric boundary-layer (SBL during the WELSONS (wind erosion and losses of soil nutrients in semiarid Spain experiment. Some Mediterranean regions suffer land degradation by wind erosion as a consequence of their particular soil and climate conditions and inappropriate agricultural practice. In Spain, where land degradation by water erosion is well known, the lack of field studies to quantify soils losses by wind erosion resulted in the European Community organizing a scientific program for this specific issue. The European programme known as WELSONS was devoted to study the wind erosion process in central Aragon (NE Spain. This multidisciplinary experiment, which began in 1996 and finished in 1998, was carried out over an agricultural soil which was left fallow. Within the experimental field, two plots were delimited where two tillage treatments were applied, a mould-board ploughing (or conventional tillage denoted CT and chisel ploughing (reduced tillage denoted RT. This was to study on bare soil the influence of tillage method on surface conditions, saltation flux, vertical dust flux, erosion rates, dynamics characteristics such as friction velocity, roughness length, etc., and energy budget. The partitioning of the available energy, resulting from the dynamics of the SBL, are quite different over the two plots because of their own peculiar soil and surface properties. The first results show that the RT treatment seems to provide a wind erosion protection. Because of the long data recording time and particular phenomena (formation of a crust at the soil surface, very dry conditions, high wind speed for instance, these microclimatological data acquired during the WELSONS programmes may be helpful to test atmospheric boundary-layer models coupled with soil models.Key words: Hydrology (desertification - Meterology and atmospheric

Paired-Associate Learning in Young and Old Adults as Related to Stimulus Concreteness and Presentation Method

Science.gov (United States)

Witte, Kenneth L.; Freund, Joel S.

1976-01-01

Investigated the learning of young and old adults as related to two variables, stimulus concreteness (low vs. high) and presentation method (recall vs. multiple choice vs. associate matching). Main findings were: (a) the elderly did not perform as well as young adults, (b) for both groups, performance was better for the pairs with concrete…

Enhancing Learning Outcomes through New E-Textbooks: A Desirable Combination of Presentation Methods and Concept Maps

Science.gov (United States)

Huang, Kuo-Liang; Chen, Kuo-Hsiang; Ho, Chun-Heng

2014-01-01

It is possible that e-textbook readers and tablet PC's will become mainstream reading devices in the future. However, knowledge about instructional design in this field of learning sciences is inadequate. This study aimed to analyse how two factors, that is, presentation methods and concept maps, interact with cognitive load and learning…

A poster presentation as an evaluation method to facilitate reflective thinking skills in nursing education

OpenAIRE

M.M. Chabeli

2002-01-01

This article seeks to establish whether the poster presentation of a specific theme can facilitate the student’s thinking skills in nursing education. A qualitative, exploratory, descriptive and contextual research design where twenty students volunteered to take part in the study by signing an informed consent was followed. Descriptive naïve sketches were used for data collection followed by individual interviews to validate the findings. Data was analysed by means of the descriptive method ...

Influence of Specimen Preparation and Test Methods on the Flexural Strength Results of Monolithic Zirconia Materials.

Science.gov (United States)

Schatz, Christine; Strickstrock, Monika; Roos, Malgorzata; Edelhoff, Daniel; Eichberger, Marlis; Zylla, Isabella-Maria; Stawarczyk, Bogna

2016-03-09

The aim of this work was to evaluate the influence of specimen preparation and test method on the flexural strength results of monolithic zirconia. Different monolithic zirconia materials (Ceramill Zolid (Amann Girrbach, Koblach, Austria), Zenostar ZrTranslucent (Wieland Dental, Pforzheim, Germany), and DD Bio zx² (Dental Direkt, Spenge, Germany)) were tested with three different methods: 3-point, 4-point, and biaxial flexural strength. Additionally, different specimen preparation methods were applied: either dry polishing before sintering or wet polishing after sintering. Each subgroup included 40 specimens. The surface roughness was assessed using scanning electron microscopy (SEM) and a profilometer whereas monoclinic phase transformation was investigated with X-ray diffraction. The data were analyzed using a three-way Analysis of Variance (ANOVA) with respect to the three factors: zirconia, specimen preparation, and test method. One-way ANOVA was conducted for the test method and zirconia factors within the combination of two other factors. A 2-parameter Weibull distribution assumption was applied to analyze the reliability under different testing conditions. In general, values measured using the 4-point test method presented the lowest flexural strength values. The flexural strength findings can be grouped in the following order: 4-point strength values than prepared before sintering. The Weibull moduli ranged from 5.1 to 16.5. Specimens polished before sintering showed higher surface roughness values than specimens polished after sintering. In contrast, no strong impact of the polishing procedures on the monoclinic surface layer was observed. No impact of zirconia material on flexural strength was found. The test method and the preparation method significantly influenced the flexural strength values.

Rainfall assimilation in RAMS by means of the Kuo parameterisation inversion: method and preliminary results

Science.gov (United States)

Orlandi, A.; Ortolani, A.; Meneguzzo, F.; Levizzani, V.; Torricella, F.; Turk, F. J.

2004-03-01

In order to improve high-resolution forecasts, a specific method for assimilating rainfall rates into the Regional Atmospheric Modelling System model has been developed. It is based on the inversion of the Kuo convective parameterisation scheme. A nudging technique is applied to 'gently' increase with time the weight of the estimated precipitation in the assimilation process. A rough but manageable technique is explained to estimate the partition of convective precipitation from stratiform one, without requiring any ancillary measurement. The method is general purpose, but it is tuned for geostationary satellite rainfall estimation assimilation. Preliminary results are presented and discussed, both through totally simulated experiments and through experiments assimilating real satellite-based precipitation observations. For every case study, Rainfall data are computed with a rapid update satellite precipitation estimation algorithm based on IR and MW satellite observations. This research was carried out in the framework of the EURAINSAT project (an EC research project co-funded by the Energy, Environment and Sustainable Development Programme within the topic 'Development of generic Earth observation technologies', Contract number EVG1-2000-00030).

Use of results from microscopic methods in optical model calculations

International Nuclear Information System (INIS)

Lagrange, C.

1985-11-01

A concept of vectorization for coupled-channel programs based upon conventional methods is first presented. This has been implanted in our program for its use on the CRAY-1 computer. In a second part we investigate the capabilities of a semi-microscopic optical model involving fewer adjustable parameters than phenomenological ones. The two main ingredients of our calculations are, for spherical or well-deformed nuclei, the microscopic optical-model calculations of Jeukenne, Lejeune and Mahaux and nuclear densities from Hartree-Fock-Bogoliubov calculations using the density-dependent force D1. For transitional nuclei deformation-dependent nuclear structure wave functions are employed to weigh the scattering potentials for different shapes and channels [fr

Communicating patient-reported outcome scores using graphic formats: results from a mixed-methods evaluation.

Science.gov (United States)

Brundage, Michael D; Smith, Katherine C; Little, Emily A; Bantug, Elissa T; Snyder, Claire F

2015-10-01

Patient-reported outcomes (PROs) promote patient-centered care by using PRO research results ("group-level data") to inform decision making and by monitoring individual patient's PROs ("individual-level data") to inform care. We investigated the interpretability of current PRO data presentation formats. This cross-sectional mixed-methods study randomized purposively sampled cancer patients and clinicians to evaluate six group-data or four individual-data formats. A self-directed exercise assessed participants' interpretation accuracy and ratings of ease-of-understanding and usefulness (0 = least to 10 = most) of each format. Semi-structured qualitative interviews explored helpful and confusing format attributes. We reached thematic saturation with 50 patients (44 % < college graduate) and 20 clinicians. For group-level data, patients rated simple line graphs highest for ease-of-understanding and usefulness (median 8.0; 33 % selected for easiest to understand/most useful) and clinicians rated simple line graphs highest for ease-of-understanding and usefulness (median 9.0, 8.5) but most often selected line graphs with confidence limits or norms (30 % for each format for easiest to understand/most useful). Qualitative results support that clinicians value confidence intervals, norms, and p values, but patients find them confusing. For individual-level data, both patients and clinicians rated line graphs highest for ease-of-understanding (median 8.0 patients, 8.5 clinicians) and usefulness (median 8.0, 9.0) and selected them as easiest to understand (50, 70 %) and most useful (62, 80 %). The qualitative interviews supported highlighting scores requiring clinical attention and providing reference values. This study has identified preferences and opportunities for improving on current formats for PRO presentation and will inform development of best practices for PRO presentation. Both patients and clinicians prefer line graphs across group-level data and individual

Presentation of RTE results 2003; Bilan electrique francais 2003

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-07-01

In 2003, RTE recorded a clear improvement in its financial results, and continued its debt reduction programme. The financial year 2003 was marked by a clear improvement in RTE's financial performance: results exceeded objectives, with turnover growing strongly, net income reached levels almost three times higher than those recorded in 2002, the economic rate of return rose to 7.1%, and debt was reduced by 470 Meuros. These results are explained by the substantial improvement in productivity, which has risen by 5% per year on average over the last three years. Net income has almost tripled due to RTE's improved productivity completed by a significant rise in its turnover and stabilizing operating costs RTE's finances therefore remain healthy, enabling the company to continue its debt reduction programme. Satisfactory economic and financial rates of return. Deadlines facing RTE in 2004: in application of the second European Directive, adopted on 26 June 2003, RTE faces two major deadlines in 2004: - the implementation of the 2. phase in the process of opening up the French electricity market, - its legal independence. On 1 July 2004, the market will be opened up to competition for all professional customers. At that date RTE, like all other electricity transmission system operators (TSOs) in the European Union, should be a legally independent body. The new central role of TSOs in Europe: how are electricity transmission system operators in other EU countries organised?.

LOGICAL CONDITIONS ANALYSIS METHOD FOR DIAGNOSTIC TEST RESULTS DECODING APPLIED TO COMPETENCE ELEMENTS PROFICIENCY

Directory of Open Access Journals (Sweden)

V. I. Freyman

2015-11-01

Full Text Available Subject of Research.Representation features of education results for competence-based educational programs are analyzed. Solution importance of decoding and proficiency estimation for elements and components of discipline parts of competences is shown. The purpose and objectives of research are formulated. Methods. The paper deals with methods of mathematical logic, Boolean algebra, and parametrical analysis of complex diagnostic test results, that controls proficiency of some discipline competence elements. Results. The method of logical conditions analysis is created. It will give the possibility to formulate logical conditions for proficiency determination of each discipline competence element, controlled by complex diagnostic test. Normalized test result is divided into noncrossing zones; a logical condition about controlled elements proficiency is formulated for each of them. Summarized characteristics for test result zones are imposed. An example of logical conditions forming for diagnostic test with preset features is provided. Practical Relevance. The proposed method of logical conditions analysis is applied in the decoding algorithm of proficiency test diagnosis for discipline competence elements. It will give the possibility to automate the search procedure for elements with insufficient proficiency, and is also usable for estimation of education results of a discipline or a component of competence-based educational program.

Monitoring ambient ozone with a passive measurement technique method, field results and strategy

NARCIS (Netherlands)

Scheeren, BA; Adema, EH

1996-01-01

A low-cost, accurate and sensitive passive measurement method for ozone has been developed and tested. The method is based on the reaction of ozone with indigo carmine which results in colourless reaction products which are detected spectrophotometrically after exposure. Coated glass filters are

[Results of treatment of milk teeth pulp by modified formocresol method].

Science.gov (United States)

Wochna-Sobańska, M

1989-01-01

The purpose of the study was evaluation of the results of treatment of molar pulp diseases by the formocresol method from the standpoint of the development of inflammatory complications in periapical tissues, disturbances of physiological resorption of roots, disturbances of mineralization of crowns of homologous permanent teeth. For the treatment milk molars were qualified with the diagnosis of grade II pulpopathy in children aged from 3 to 9 years. The treatment was done using formocresol by a modified method of pulp amputation according to Buckley after previous devitalization with parapaste. The status of 143 teeth was examined again 1 to 4 years after completion of treatment. The proportion of positive results after one year was 94%, after two years it was 90%, after three years 87% and after four years 80%. The cause of premature loss of most teeth was root resorption acceleration by 18-24 months. No harmful action of formocresol on the buds of permanent teeth was noted.

Climatic Change--Past, Present & Future

Science.gov (United States)

Lindholm, Roy C.

1976-01-01

Presented is a review of studies investigating factors affecting climatic changes in the Earth's atmosphere--past, present, and future. Dating methods, particularly the Oxygen 18/16 method, are discussed. (SL)

Resource costing for multinational neurologic clinical trials: methods and results.

Science.gov (United States)

Schulman, K; Burke, J; Drummond, M; Davies, L; Carlsson, P; Gruger, J; Harris, A; Lucioni, C; Gisbert, R; Llana, T; Tom, E; Bloom, B; Willke, R; Glick, H

1998-11-01

We present the results of a multinational resource costing study for a prospective economic evaluation of a new medical technology for treatment of subarachnoid hemorrhage within a clinical trial. The study describes a framework for the collection and analysis of international resource cost data that can contribute to a consistent and accurate intercountry estimation of cost. Of the 15 countries that participated in the clinical trial, we collected cost information in the following seven: Australia, France, Germany, the UK, Italy, Spain, and Sweden. The collection of cost data in these countries was structured through the use of worksheets to provide accurate and efficient cost reporting. We converted total average costs to average variable costs and then aggregated the data to develop study unit costs. When unit costs were unavailable, we developed an index table, based on a market-basket approach, to estimate unit costs. To estimate the cost of a given procedure, the market-basket estimation process required that cost information be available for at least one country. When cost information was unavailable in all countries for a given procedure, we estimated costs using a method based on physician-work and practice-expense resource-based relative value units. Finally, we converted study unit costs to a common currency using purchasing power parity measures. Through this costing exercise we developed a set of unit costs for patient services and per diem hospital services. We conclude by discussing the implications of our costing exercise and suggest guidelines to facilitate more effective multinational costing exercises.

The present state of research into plasma heating and injection methods

International Nuclear Information System (INIS)

1974-12-01

The advantages and disadvantages recognized by the Advisory Group on Heating and injection for twelve plasma heating and injection methods currently under investigation in Europe are related. The heating and injection requirements of four reference reactor designs are previously defined. The problems which arise when one attempts to extrapolate existing work towards the reactor goal are emphasized. Two refuelling methods not directly linked with the heating problem are discussed. The experiments in operation or under construction in Europe in which each method is investigated are listed. Sixteen working papers which served as a basis for the Advisory Group discussion and which cover all the heating and injection methods examined are included

Evaluating mediation and moderation effects in school psychology: a presentation of methods and review of current practice.

Science.gov (United States)

Fairchild, Amanda J; McQuillin, Samuel D

2010-02-01

Third variable effects elucidate the relation between two other variables, and can describe why they are related or under what conditions they are related. This article demonstrates methods to analyze two third-variable effects: moderation and mediation. The utility of examining moderation and mediation effects in school psychology is described and current use of the analyses in applied school psychology research is reviewed and evaluated. Proper statistical methods to test the effects are presented, and different effect size measures for the models are provided. Extensions of the basic moderator and mediator models are also described.

Lagrangian methods for blood damage estimation in cardiovascular devices--How numerical implementation affects the results.

Science.gov (United States)

Marom, Gil; Bluestein, Danny

2016-01-01

This paper evaluated the influence of various numerical implementation assumptions on predicting blood damage in cardiovascular devices using Lagrangian methods with Eulerian computational fluid dynamics. The implementation assumptions that were tested included various seeding patterns, stochastic walk model, and simplified trajectory calculations with pathlines. Post processing implementation options that were evaluated included single passage and repeated passages stress accumulation and time averaging. This study demonstrated that the implementation assumptions can significantly affect the resulting stress accumulation, i.e., the blood damage model predictions. Careful considerations should be taken in the use of Lagrangian models. Ultimately, the appropriate assumptions should be considered based the physics of the specific case and sensitivity analysis, similar to the ones presented here, should be employed.

Relative Effects of Visualized and Verbal Presentation Methods in Communicating Environmental Information among Stakeholders: Okavango Delta, Botswana

Science.gov (United States)

Thakadu, Olekae T.; Irani, Tracy; Telg, Ricky

2011-01-01

The present study examined the relative effectiveness of 2 public instructional communication methods in improving selected predictors of knowledge-sharing behaviors among communities in the Okavango Delta, Botswana. A total of 120 subjects took part in a quasiexperimental study, with 2 experimental treatments: (a) visualized PowerPoint…

Near threshold absolute TDCS: First results

International Nuclear Information System (INIS)

Roesel, T.; Schlemmer, P.; Roeder, J.; Frost, L.; Jung, K.; Ehrhardt, H.

1992-01-01

A new method, and first results for an impact energy 2 eV above the threshold of ionisation of helium, are presented for the measurement of absolute triple differential cross sections (TDCS) in a crossed beam experiment. The method is based upon measurement of beam/target overlap densities using known absolute total ionisation cross sections and of detection efficiencies using known absolute double differential cross sections (DDCS). For the present work the necessary absolute DDCS for 1 eV electrons had also to be measured. Results are presented for several different coplanar kinematics and are compared with recent DWBA calculations. (orig.)

Recent SUSY Results from CMS

CERN Multimedia

CERN. Geneva

2012-01-01

We present a summary of the recent results of searches for supersymmetry conducted by the CMS experiment. Several searches are reported using complementary final states and methods. The results presented include searches for stops and sbottoms, production of charginos and neutralinos, and R-parity violating signatures. Several of them are the first results of their kind from CMS, while others increased the mass reach significantly over previously published results from the LHC.

Assessing Cost-Effectiveness in Obesity (ACE-Obesity: an overview of the ACE approach, economic methods and cost results

Directory of Open Access Journals (Sweden)

Swinburn Boyd

2009-11-01

Full Text Available Abstract Background The aim of the ACE-Obesity study was to determine the economic credentials of interventions which aim to prevent unhealthy weight gain in children and adolescents. We have reported elsewhere on the modelled effectiveness of 13 obesity prevention interventions in children. In this paper, we report on the cost results and associated methods together with the innovative approach to priority setting that underpins the ACE-Obesity study. Methods The Assessing Cost Effectiveness (ACE approach combines technical rigour with 'due process' to facilitate evidence-based policy analysis. Technical rigour was achieved through use of standardised evaluation methods, a research team that assembles best available evidence and extensive uncertainty analysis. Cost estimates were based on pathway analysis, with resource usage estimated for the interventions and their 'current practice' comparator, as well as associated cost offsets. Due process was achieved through involvement of stakeholders, consensus decisions informed by briefing papers and 2nd stage filter analysis that captures broader factors that influence policy judgements in addition to cost-effectiveness results. The 2nd stage filters agreed by stakeholders were 'equity', 'strength of the evidence', 'feasibility of implementation', 'acceptability to stakeholders', 'sustainability' and 'potential for side-effects'. Results The intervention costs varied considerably, both in absolute terms (from cost saving [6 interventions] to in excess of AUD50m per annum and when expressed as a 'cost per child' estimate (from Conclusion The use of consistent methods enables valid comparison of potential intervention costs and cost-offsets for each of the interventions. ACE-Obesity informs policy-makers about cost-effectiveness, health impact, affordability and 2nd stage filters for important options for preventing unhealthy weight gain in children. In related articles cost-effectiveness results and

Methods for estimating uncertainty in PMF solutions: examples with ambient air and water quality data and guidance on reporting PMF results.

Science.gov (United States)

Brown, Steven G; Eberly, Shelly; Paatero, Pentti; Norris, Gary A

2015-06-15

The new version of EPA's positive matrix factorization (EPA PMF) software, 5.0, includes three error estimation (EE) methods for analyzing factor analytic solutions: classical bootstrap (BS), displacement of factor elements (DISP), and bootstrap enhanced by displacement (BS-DISP). These methods capture the uncertainty of PMF analyses due to random errors and rotational ambiguity. To demonstrate the utility of the EE methods, results are presented for three data sets: (1) speciated PM2.5 data from a chemical speciation network (CSN) site in Sacramento, California (2003-2009); (2) trace metal, ammonia, and other species in water quality samples taken at an inline storage system (ISS) in Milwaukee, Wisconsin (2006); and (3) an organic aerosol data set from high-resolution aerosol mass spectrometer (HR-AMS) measurements in Las Vegas, Nevada (January 2008). We present an interpretation of EE diagnostics for these data sets, results from sensitivity tests of EE diagnostics using additional and fewer factors, and recommendations for reporting PMF results. BS-DISP and BS are found useful in understanding the uncertainty of factor profiles; they also suggest if the data are over-fitted by specifying too many factors. DISP diagnostics were consistently robust, indicating its use for understanding rotational uncertainty and as a first step in assessing a solution's viability. The uncertainty of each factor's identifying species is shown to be a useful gauge for evaluating multiple solutions, e.g., with a different number of factors. Published by Elsevier B.V.

Developing a bone mineral density test result letter to send to patients: a mixed-methods study

Directory of Open Access Journals (Sweden)

Edmonds SW

2014-06-01

Full Text Available Stephanie W Edmonds,1,2 Samantha L Solimeo,3 Xin Lu,1 Douglas W Roblin,4,8 Kenneth G Saag,5 Peter Cram6,7 1Department of Internal Medicine, 2College of Nursing, University of Iowa, Iowa City, IA, USA; 3Center for Comprehensive Access and Delivery Research and Evaluation, Iowa City Veterans Affairs Health Care System, Iowa City, IA, USA; 4Kaiser Permanente of Atlanta, Atlanta, GA, USA; 5Department of Rheumatology, University of Alabama at Birmingham, Birmingham, AL, USA; 6Faculty of Medicine, University of Toronto, Toronto, ON, Canada; 7University Health Network and Mount Sinai Hospital, Toronto, ON, Canada; 8School of Public Health, Georgia State University, Atlanta, GA, USA Purpose: To use a mixed-methods approach to develop a letter that can be used to notify patients of their bone mineral density (BMD results by mail that may activate patients in their bone-related health care. Patients and methods: A multidisciplinary team developed three versions of a letter for reporting BMD results to patients. Trained interviewers presented these letters in a random order to a convenience sample of adults, aged 50 years and older, at two different health care systems. We conducted structured interviews to examine the respondents’ preferences and comprehension among the various letters. Results: A total of 142 participants completed the interview. A majority of the participants were female (64.1% and white (76.1%. A plurality of the participants identified a specific version of the three letters as both their preferred version (45.2%; P<0.001 and as the easiest to understand (44.6%; P<0.01. A majority of participants preferred that the letters include specific next steps for improving their bone health. Conclusion: Using a mixed-methods approach, we were able to develop and optimize a printed letter for communicating a complex test result (BMD to patients. Our results may offer guidance to clinicians, administrators, and researchers who are

Faster methods for estimating arc centre position during VAR and results from Ti-6Al-4V and INCONEL 718 alloys

Science.gov (United States)

Nair, B. G.; Winter, N.; Daniel, B.; Ward, R. M.

2016-07-01

Direct measurement of the flow of electric current during VAR is extremely difficult due to the aggressive environment as the arc process itself controls the distribution of current. In previous studies the technique of “magnetic source tomography” was presented; this was shown to be effective but it used a computationally intensive iterative method to analyse the distribution of arc centre position. In this paper we present faster computational methods requiring less numerical optimisation to determine the centre position of a single distributed arc both numerically and experimentally. Numerical validation of the algorithms were done on models and experimental validation on measurements based on titanium and nickel alloys (Ti6Al4V and INCONEL 718). The results are used to comment on the effects of process parameters on arc behaviour during VAR.

A new method of presentation the large-scale magnetic field structure on the Sun and solar corona

Science.gov (United States)

Ponyavin, D. I.

1995-01-01

The large-scale photospheric magnetic field, measured at Stanford, has been analyzed in terms of surface harmonics. Changes of the photospheric field which occur within whole solar rotation period can be resolved by this analysis. For this reason we used daily magnetograms of the line-of-sight magnetic field component observed from Earth over solar disc. We have estimated the period during which day-to-day full disc magnetograms must be collected. An original algorithm was applied to resolve time variations of spherical harmonics that reflect time evolution of large-scale magnetic field within solar rotation period. This method of magnetic field presentation can be useful enough in lack of direct magnetograph observations due to sometimes bad weather conditions. We have used the calculated surface harmonics to reconstruct the large-scale magnetic field structure on the source surface near the sun - the origin of heliospheric current sheet and solar wind streams. The obtained results have been compared with spacecraft in situ observations and geomagnetic activity. We tried to show that proposed technique can trace shon-time variations of heliospheric current sheet and short-lived solar wind streams. We have compared also our results with those obtained traditionally from potential field approximation and extrapolation using synoptic charts as initial boundary conditions.

Evaluating mediation and moderation effects in school psychology: A presentation of methods and review of current practice

Science.gov (United States)

Fairchild, Amanda J.; McQuillin, Samuel D.

2017-01-01

Third variable effects elucidate the relation between two other variables, and can describe why they are related or under what conditions they are related. This article demonstrates methods to analyze two third-variable effects: moderation and mediation. The utility of examining moderation and mediation effects in school psychology is described and current use of the analyses in applied school psychology research is reviewed and evaluated. Proper statistical methods to test the effects are presented, and different effect size measures for the models are provided. Extensions of the basic moderator and mediator models are also described. PMID:20006988

Health effects estimation: Methods and results for uranium mill tailings contaminated properties

International Nuclear Information System (INIS)

Denham, D.H.; Cross, F.T.; Soldat, J.K.

1990-01-01

This paper describes methods for estimating potential health effects from exposure to uranium mill tailings and presents a summary of risk projections for 50 contaminated properties (residences, schools, churches, and businesses) in the US. The methods provide realistic estimates of cancer risk to exposed individuals based on property-specific occupancy and contamination patterns. External exposure to gamma radiation, inhalation of radon daughters, and consumption of food products grown in radium-contaminated soil are considered. Most of the projected risk was from indoor exposure to radon daughters; however, for some properties the risk from consumption of locally grown food products is similar to that from radon daughters. In all cases, the projected number of lifetime cancer deaths for specific properties is less than one, but for some properties the increase in risk over that normally expected is greater than 100%

First characterization of the expiratory flow increase technique: method development and results analysis

International Nuclear Information System (INIS)

Maréchal, L; Barthod, C; Jeulin, J C

2009-01-01

This study provides an important contribution to the definition of the expiratory flow increase technique (EFIT). So far, no measuring means were suited to assess the manual EFIT performed on infants. The proposed method aims at objectively defining the EFIT based on the quantification of pertinent cognitive parameters used by physiotherapists when practicing. We designed and realized customized instrumented gloves endowed with pressure and displacement sensors, and the associated electronics and software. This new system is specific to the manoeuvre, to the user and innocuous for the patient. Data were collected and analysed on infants with bronchiolitis managed by an expert physiotherapist. The analysis presented is realized on a group of seven subjects (mean age: 6.1 months, SD: 1.1; mean chest circumference: 44.8 cm, SD: 1.9). The results are consistent with the physiotherapist's tactility. In spite of inevitable variability due to measurements on infants, repeatable quantitative data could be reported regarding the manoeuvre characteristics: the magnitudes of displacements do not exceed 10 mm on both hands; the movement of the thoracic hand is more vertical than the movement of the abdominal hand; the maximum applied pressure with the thoracic hand is about twice higher than with the abdominal hand; the thrust of the manual compression lasts (590 ± 62) ms. Inter-operators measurements are in progress in order to generalize these results

The Role of Learning- and Presentation- Portfolios in Design Educations

DEFF Research Database (Denmark)

Thomsen, Bente Dahl; Ovesen, Nis

2014-01-01

Students that primarily study design through team-based projects often struggle to develop presentation portfolios that differentiate from the ones of other students. In the industry, design managers experience this as a problem, as they often receive job applications with presentation portfolios...... resources from other activities, which is why the templates have to be carefully balanced in order to achieve the desired effect. The portfolio method proved to be especially good at illustrating process related competencies.......Students that primarily study design through team-based projects often struggle to develop presentation portfolios that differentiate from the ones of other students. In the industry, design managers experience this as a problem, as they often receive job applications with presentation portfolios...... of the portfolio method in engineering design educations, this research project has investigated the method as part of a course programme. The preliminary experiments and results show that learning portfolio templates are effective in strengthening certain activities. On the other hand, the method risks draining...

Interval estimation methods of the mean in small sample situation and the results' comparison

International Nuclear Information System (INIS)

Wu Changli; Guo Chunying; Jiang Meng; Lin Yuangen

2009-01-01

The methods of the sample mean's interval estimation, namely the classical method, the Bootstrap method, the Bayesian Bootstrap method, the Jackknife method and the spread method of the Empirical Characteristic distribution function are described. Numerical calculation on the samples' mean intervals is carried out where the numbers of the samples are 4, 5, 6 respectively. The results indicate the Bootstrap method and the Bayesian Bootstrap method are much more appropriate than others in small sample situation. (authors)

Introduction of a method for presenting health-based impacts of the emission from products, based on emission measurements of materials used in manufacturing of the products

Energy Technology Data Exchange (ETDEWEB)

Jørgensen, Rikke Bramming, E-mail: rikke.jorgensen@iot.ntnu.no

2013-11-15

A method for presenting the health impact of emissions from furniture is introduced, which could be used in the context of environmental product declarations. The health impact is described by the negative indoor air quality potential, the carcinogenic potential, the mutagenic and reprotoxic potential, the allergenic potential, and the toxicological potential. An experimental study of emissions from four pieces of furniture is performed by testing both the materials used for production of the furniture and the complete piece of furniture, in order to compare the results gained by adding emissions of material with results gained from testing the finished piece of furniture. Calculating the emission from a product based on the emission from materials used in the manufacture of the product is a new idea. The relation between calculated results and measured results from the same products differ between the four pieces of furniture tested. Large differences between measured and calculated values are seen for leather products. More knowledge is needed to understand why these differences arise. Testing materials allows us to compare different suppliers of the same material. Four different foams and three different timber materials are tested, and the results vary between materials of the same type. If the manufacturer possesses this type of knowledge of the materials from the subcontractors it could be used as a selection criterion according to production of low emission products. -- Highlights: • A method for presenting health impact of emissions is introduced. • An experimental study of emissions from four pieces of furniture is performed. • Health impact is calculated based on sum of contribution from the materials used. • Calculated health impact is compared to health impact of the manufactured product. • The results show that health impact could be useful in product development and for presentation in EPDs.

Auto-correlation based intelligent technique for complex waveform presentation and measurement

International Nuclear Information System (INIS)

Rana, K P S; Singh, R; Sayann, K S

2009-01-01

Waveform acquisition and presentation forms the heart of many measurement systems. Particularly, data acquisition and presentation of repeating complex signals like sine sweep and frequency-modulated signals introduces the challenge of waveform time period estimation and live waveform presentation. This paper presents an intelligent technique, for waveform period estimation of both the complex and simple waveforms, based on the normalized auto-correlation method. The proposed technique is demonstrated using LabVIEW based intensive simulations on several simple and complex waveforms. Implementation of the technique is successfully demonstrated using LabVIEW based virtual instrumentation. Sine sweep vibration waveforms are successfully presented and measured for electrodynamic shaker system generated vibrations. The proposed method is also suitable for digital storage oscilloscope (DSO) triggering, for complex signals acquisition and presentation. This intelligence can be embodied into the DSO, making it an intelligent measurement system, catering wide varieties of the waveforms. The proposed technique, simulation results, robustness study and implementation results are presented in this paper.

New results to BDD truncation method for efficient top event probability calculation

International Nuclear Information System (INIS)

Mo, Yuchang; Zhong, Farong; Zhao, Xiangfu; Yang, Quansheng; Cui, Gang

2012-01-01

A Binary Decision Diagram (BDD) is a graph-based data structure that calculates an exact top event probability (TEP). It has been a very difficult task to develop an efficient BDD algorithm that can solve a large problem since its memory consumption is very high. Recently, in order to solve a large reliability problem within limited computational resources, Jung presented an efficient method to maintain a small BDD size by a BDD truncation during a BDD calculation. In this paper, it is first identified that Jung's BDD truncation algorithm can be improved for a more practical use. Then, a more efficient truncation algorithm is proposed in this paper, which can generate truncated BDD with smaller size and approximate TEP with smaller truncation error. Empirical results showed this new algorithm uses slightly less running time and slightly more storage usage than Jung's algorithm. It was also found, that designing a truncation algorithm with ideal features for every possible fault tree is very difficult, if not impossible. The so-called ideal features of this paper would be that with the decrease of truncation limits, the size of truncated BDD converges to the size of exact BDD, but should never be larger than exact BDD.

Analytical method and result of radiation exposure for depressurization accident of HTTR

International Nuclear Information System (INIS)

Sawa, K.; Shiozawa, S.; Mikami, H.

1990-01-01

The Japan Atomic Energy Research Institute (JAERI) is now proceeding with the construction design of the High Temperature Engineering Test Reactor (HTTR). Since the HTTR has some characteristics different from LWRs, analytical method of radiation exposure in accidents provided for LWRs can not be applied directly. This paper describes the analytical method of radiation exposure developed by JAERI for the depressurization accident, which is the severest accident in respect to radiation exposure among the design basis accidents of the HTTR. The result is also described in this paper

Methods for detecting and correcting inaccurate results in inductively coupled plasma-atomic emission spectrometry

Science.gov (United States)

Chan, George C. Y. [Bloomington, IN; Hieftje, Gary M [Bloomington, IN

2010-08-03

A method for detecting and correcting inaccurate results in inductively coupled plasma-atomic emission spectrometry (ICP-AES). ICP-AES analysis is performed across a plurality of selected locations in the plasma on an unknown sample, collecting the light intensity at one or more selected wavelengths of one or more sought-for analytes, creating a first dataset. The first dataset is then calibrated with a calibration dataset creating a calibrated first dataset curve. If the calibrated first dataset curve has a variability along the location within the plasma for a selected wavelength, errors are present. Plasma-related errors are then corrected by diluting the unknown sample and performing the same ICP-AES analysis on the diluted unknown sample creating a calibrated second dataset curve (accounting for the dilution) for the one or more sought-for analytes. The cross-over point of the calibrated dataset curves yields the corrected value (free from plasma related errors) for each sought-for analyte.

Creep in rock salt with temperature. Testing methods and results

International Nuclear Information System (INIS)

Charpentier, J.P.; Berest, P.

1985-01-01

The growing interest shown in the delayed behaviour of rocks at elevated temperature has led the Solid Mechanics Laboratory to develop specific equipment designed for creep tests. The design and dimensioning of these units offer the possibility of investigating a wide range of materials. The article describes the test facilities used (uni-axial and tri-axial creep units) and presents the experimental results obtained on samples of Bresse salt [fr

One-at-a-time versus grouped presentation of mug book pictures: some surprising results.

Science.gov (United States)

Stewart, H A; McAllister, H A

2001-12-01

Eyewitnesses to a simulated crime attempted to identify the perpetrator from a computerized mug book. The 208 mug book pictures were presented either 1 mug shot per page or in groups of 12 mug shots per page. Half of the mug books were arranged by similarity to the perpetrator as determined by a facial recognition algorithm, and half were randomly arranged. In contrast to past findings with photospreads, false-positive identifications were significantly higher using the one-at-a-time procedure than the grouped procedure. Results suggest that the best practice for mug books may be the use of groups of pictures per page rather than the one-at-a-time procedure long advocated by experts for use in lineups and photospreads.

INTERDISCIPLINARITY IN PUBLIC SPACE PARTICIPATIVE PROJECTS: METHODS AND RESULTS IN PRACTICE AND TEACHING

Directory of Open Access Journals (Sweden)

Pedro Brandão

2015-06-01

• In the development of design practice and studio teaching methods We shall see in this paper how interdisciplinary approaches correspond to new and complex urban transformations, focusing on the importance of actors’ interaction processes, combining professional and non-professional knowledge and theory-practice relations. Therefore, we aim at a deepening in public space area of knowledge under the growing complexity of urban life. We see it as a base for further development of collaborative projects and their implications on community empowerment and urban governance at local level. Motivations of this line of work are persistent in several ongoing research projects, aiming to: - Understand public space as a cohesion factor both in urban life and urban form - Manage processes and strategies as elements of urban transformation, - Stimulate the understanding of actors’ roles in urban design practices. - Favoring the questioning of emerging aspects of urban space production… The paper presents and analyses processes, methods and results from civic participation projects developed in the neighbourhood of Barò de Viver (Barcelona and in the District of Marvila (Lisbon. In the first case, a long process initiated in 2004 and partially completed in 2011, neighbours developed the projects "Memory Wall" and Ciutat d'Asuncion Promenade as part of identity construction in public space, in collaboration  with a team of facilitators from CrPolis group. In the second case, different participatory processes dated from 2001 and 2003 have resulted in the implementation of a specific identity urban brand and communication system with an ongoing project of "maps" construction according to the neighbours perception and representation systems. We may conclude that processes of urban governance require more active participation of citizens in projects regarding the improvement of quality of life. At the same time, the implementation of these processes requires a clear

METHODS OF MEASURING THE EFFECTS OF LIGHTNING BY SIMULATING ITS STRIKES WITH THE INTERVAL ASSESSMENT OF THE RESULTS OF MEASUREMENTS

Directory of Open Access Journals (Sweden)

P. V. Kriksin

2017-01-01

Full Text Available The article presents the results of the development of new methods aimed at more accurate interval estimate of the experimental values of voltages on grounding devices of substations and circuits in the control cables, that occur when lightning strikes to lightning rods; the abovementioned estimate made it possible to increase the accuracy of the results of the study of lightning noise by 28 %. A more accurate value of interval estimation were achieved by developing a measurement model that takes into account, along with the measured values, different measurement errors and includes the special processing of the measurement results. As a result, the interval of finding the true value of the sought voltage is determined with an accuracy of 95 %. The methods can be applied to the IK-1 and IKP-1 measurement complexes, consisting in the aperiodic pulse generator, the generator of high-frequency pulses and selective voltmeters, respectively. To evaluate the effectiveness of the developed methods series of experimental voltage assessments of grounding devices of ten active high-voltage substation have been fulfilled in accordance with the developed methods and traditional techniques. The evaluation results confirmed the possibility of finding the true values of voltage over a wide range, that ought to be considered in the process of technical diagnostics of lightning protection of substations when the analysis of the measurement results and the development of measures to reduce the effects of lightning are being fulfilled. Also, a comparative analysis of the results of measurements made in accordance with the developed methods and traditional techniques has demonstrated that the true value of the sought voltage may exceed the measured value at an average of 28 %, that ought to be considered in the further analysis of the parameters of lightning protection at the facility and in the development of corrective actions. The developed methods have been

Determination of the food consumption in eleven regions of the european community with a view to studying the radioactive contamination level: Methods used. Results of family enquiries

International Nuclear Information System (INIS)

Cresta, M.; Lacourly, G.

1966-01-01

In the present report are given the results obtained from food surveys carried out during the period 1963-1965 and involving 9000 families living in eleven regions spread out over the six European Community countries. A partial analysis of the results obtained covers a reduced sample of 3725 families; it makes it possible to fix the composition of the mean individual, monthly and annual food consumptions for each of the eleven regions. Details of the organisation of the survey, of the data processing methods and of the method of presenting the results are given in the first part of the report. the second part presents, in numerical table form, the consumption of various foodstuffs and the feeding principles for each region covered by the survey. Tables summarizing the data make it possible to compare the mean individual consumptions in the various regions studied. (author) [fr

Delayed Presentation of Isolated Complete Pancreatic Transection as a Result of Sport-Related Blunt Trauma to the Abdomen

Directory of Open Access Journals (Sweden)

Andrew J. Healey

2008-01-01

Full Text Available Introduction: Blunt abdominal trauma is a rare but well-recognized cause of pancreatic transection. A delayed presentation of pancreatic fracture following sport-related blunt trauma with the coexisting diagnostic pitfalls is presented. Case Report: A 17-year-old rugby player was referred to our specialist unit after having been diagnosed with traumatic pancreatic transection, having presented 24 h after a sporting injury. Despite haemodynamic stability, at laparotomy he was found to have a diffuse mesenteric hematoma involving the large and small bowel mesentery, extending down to the sigmoid colon from the splenic flexure, and a large retroperitoneal hematoma arising from the pancreas. The pancreas was completely severed with the superior border of the distal segment remaining attached to the splenic vein that was intact. A distal pancreatectomy with spleen preservation and evacuation of the retroperitoneal hematoma was performed. Discussion/Conclusion: Blunt pancreatic trauma is a serious condition. Diagnosis and treatment may often be delayed, which in turn may drastically increase morbidity and mortality. Diagnostic difficulties apply to both paraclinical and radiological diagnostic methods. A high index of suspicion should be maintained in such cases, with a multi-modality diagnostic approach and prompt surgical intervention as required.

Evaluation of the effects of green taxes in the Nordic countries. Results and method question

International Nuclear Information System (INIS)

Skou Andersen, M.; Dengsoee, N.; Branth Pedersen, A.

2000-01-01

Green taxes have over the past 10 years become a significant part of environmental regulation in the Nordic countries. The present report is a literature study of the effects of green taxes with regard to CO 2 and pesticides. The authors have identified 68 studies of CO 2 -taxes and 20 studies of the pesticide taxes. The report presents a summary of the results from these studies and assesses the methodologies employed for examining the effects of the green taxes. The majority of the reviewed studies are ex-ante studies, which have been carried out in advance of the implementation of the taxes, and which are often based on simplified economic models. Ex-post studies, which are based on the actual historical data for the adjustment to the taxes, are relatively few. 20 ex-post studies of the CO 2 -taxes have been identified, while there are not any ex-post studies of the pesticide taxes. With regard to the environmental effects of green taxes, the ex-post studies can be relied on for the procurement of the most reliable data. The completed ex-post studies of the CO 2 -taxes do not present unambiguous results, because focus and methodology differ. Most studies are partial in their focus and relate to one or more sectors of the economy. Some studies have been carried out few tears after the introduction of the taxes, and do not present an updated assessment of the effects of the taxes. To the extent that it is possible to summarise the present knowledge about the effects of the CO 2 -taxes, there seems to be indications for relatively marked effects in Denmark as compared to the other Nordic countries, since Denmark is the only country whose taxed CO 2 -emissions have been reduced in absolute figures. With regard to Norway and Sweden, effects of the CO 2 -taxes can be identified in particular sectors in relation to business-as-usual scenarios. Finland's CO 2 -tax has not been comprehensively evaluated ex-post, but has reached a tax level which gives expectations of

CT-guided percutaneous neurolysis methods. State of the art and first results

International Nuclear Information System (INIS)

Schneider, B.; Richter, G.M.; Roeren, T.; Kauffmann, G.W.

1996-01-01

We used 21G or 22G fine needles. All CT-guided percutaneous neurolysis methods require a proper blood coagulation. Most common CT scanners are suitable for neurolysis if there is enough room for maintaining sterile conditions. All neurolysis methods involve sterile puncture of the ganglia under local anesthesia, a test block with anesthetic and contrast agent to assess the clinical effect and the definitive block with a mixture of 96% ethanol and local anesthetic. This allows us to correct the position of the needle if we see improper distribution of the test block or unwanted side effects. Though inflammatory complications of the peritoneum due to puncture are rarely seen, we prefer the dorsal approach whenever possible. Results: Seven of 20 legs showed at least transient clinical improvement after CT-guided lumbar sympathectomies; 13 legs had to be amputated. Results of the methods in the literature differ. For lumbar sympathectomy, improved perfusion is reported in 39-89%, depending on the pre-selection of the patient group. Discussion: It was recently proved that sympathectomy not only improves perfusion of the skin but also of the muscle. The hypothesis of a steal effect after sympathectomy towards skin perfusion was disproved. Modern aggressive surgical and interventional treatment often leaves patients to sympathectomy whose reservers of collateralization are nearly exhausted. We presume this is the reason for the different results we found in our patient group. For thoracic sympathectomy the clinical treatment depends very much on the indications. Whereas palmar hyperhidrosis offers nearly 100% success, only 60-70% of patients with disturbance of perfusion have benefited. Results in celiac ganglia block also differ. Patients with carcinoma of the pancreas and other organs of the upper abdomen benefit in 80-100% of all cases, patients with chronic pancreatitis in 60-80%. (orig./VHE) [de

Tank 48H Waste Composition and Results of Investigation of Analytical Methods

Energy Technology Data Exchange (ETDEWEB)

Walker , D.D. [Westinghouse Savannah River Company, AIKEN, SC (United States)

1997-04-02

This report serves two purposes. First, it documents the analytical results of Tank 48H samples taken between April and August 1996. Second, it describes investigations of the precision of the sampling and analytical methods used on the Tank 48H samples.

Late presentation of HIV infection: a consensus definition

DEFF Research Database (Denmark)

Antinori, A; Coenen, T; Costagiola, D

2010-01-01

clinical definition of late presentation. The objective of this article is to present a consensus definition of late presentation of HIV infection. Methods Over the past year, two initiatives have moved towards a harmonized definition. In spring 2009, they joined efforts to identify a common definition...... of what is meant by a 'late-presenting' patient. Results Two definitions were agreed upon, as follows. Late presentation: persons presenting for care with a CD4 count below 350 cells/muL or presenting with an AIDS-defining event, regardless of the CD4 cell count. Presentation with advanced HIV disease...... able to implement this definition (either on its own or alongside their own preferred definition) when reporting surveillance or research data relating to late presentation of HIV infection....

The rank-heat plot is a novel way to present the results from a network meta-analysis including multiple outcomes.

Science.gov (United States)

Veroniki, Areti Angeliki; Straus, Sharon E; Fyraridis, Alexandros; Tricco, Andrea C

2016-08-01

To present a novel and simple graphical approach to improve the presentation of the treatment ranking in a network meta-analysis (NMA) including multiple outcomes. NMA simultaneously compares many relevant interventions for a clinical condition from a network of trials, and allows ranking of the effectiveness and/or safety of each intervention. There are numerous ways to present the NMA results, which can challenge their interpretation by research users. The rank-heat plot is a novel graph that can be used to quickly recognize which interventions are most likely the best or worst interventions with respect to their effectiveness and/or safety for a single or multiple outcome(s) and may increase interpretability. Using empirical NMAs, we show that the need for a concise and informative presentation of results is imperative, particularly as the number of competing treatments and outcomes in an NMA increases. The rank-heat plot is an efficient way to present the results of ranking statistics, particularly when a large amount of data is available, and it is targeted to users from various backgrounds. Copyright © 2016 Elsevier Inc. All rights reserved.

Development of methods to measure hemoglobin adducts by gel electrophoresis - Preliminary results

International Nuclear Information System (INIS)

Sun, J.D.; McBride, S.M.

1988-01-01

Chemical adducts formed on blood hemoglobin may be a useful biomarker for assessing human exposures to these compounds. This paper reports preliminary results in the development of methods to measure such adducts that may be generally applicable for a wide variety of chemicals. Male F344/N rats were intraperitoneally injected with 14 C-BaP dissolved in corn oil. Twenty-four hours later, the rats were sacrificed. Blood samples were collected and globin was isolated. Globin protein was then cleaved into peptide fragments using cyanogen bromide and the fragments separated using 2-dimensional gel electrophoresis. The results showed that the adducted 14 C-globin fragments migrated to different areas of the gel than did unadducted fragments. Further research is being conducted to develop methods that will allow quantitation of separated adducted globin fragments from human blood samples without the use of a radiolabel. (author)

Use of statistical study methods for the analysis of the results of the imitation modeling of radiation transfer

Science.gov (United States)

Alekseenko, M. A.; Gendrina, I. Yu.

2017-11-01

Recently, due to the abundance of various types of observational data in the systems of vision through the atmosphere and the need for their processing, the use of various methods of statistical research in the study of such systems as correlation-regression analysis, dynamic series, variance analysis, etc. is actual. We have attempted to apply elements of correlation-regression analysis for the study and subsequent prediction of the patterns of radiation transfer in these systems same as in the construction of radiation models of the atmosphere. In this paper, we present some results of statistical processing of the results of numerical simulation of the characteristics of vision systems through the atmosphere obtained with the help of a special software package.1

Presentation of the 1998 financial results of the Framatome group

International Nuclear Information System (INIS)

Vignon, D.

1999-01-01

This document makes a statement of the activity of the Framatome group during the year 1998. The activities of the group are shared into two main sectors of comparable size: the energy sector (nuclear fuels, nuclear realizations, nuclear services and industrial equipments) and the connectors engineering sector (electronics, electricity, automotive industry, interconnections and microelectronics). The financial results show an important growth of the connectors engineering sector while the energy sector remained satisfactory. Results are detailed by sector and activity: energy (realizations and nuclear equipments, nuclear services, nuclear fuels and industrial equipments), connectors engineering, and research and development activity of the group. (J.S.)

Performance of various mathematical methods for calculation of radioimmunoassay results

International Nuclear Information System (INIS)

Sandel, P.; Vogt, W.

1977-01-01

Interpolation and regression methods are available for computer aided determination of radioimmunological end results. We compared the performance of eight algorithms (weighted and unweighted linear logit-log regression, quadratic logit-log regression, Rodbards logistic model in the weighted and unweighted form, smoothing spline interpolation with a large and small smoothing factor and polygonal interpolation) on the basis of three radioimmunoassays with different reference curve characteristics (digoxin, estriol, human chorionic somatomammotropin = HCS). Great store was set by the accuracy of the approximation at the intermediate points on the curve, ie. those points that lie midway between two standard concentrations. These concentrations were obtained by weighing and inserted as unknown samples. In the case of digoxin and estriol the polygonal interpolation provided the best results while the weighted logit-log regression proved superior in the case of HCS. (orig.) [de

A poster presentation as an evaluation method to facilitate reflective thinking skills in nursing education

Directory of Open Access Journals (Sweden)

M.M. Chabeli

2002-09-01

Full Text Available This article seeks to establish whether the poster presentation of a specific theme can facilitate the student’s thinking skills in nursing education. A qualitative, exploratory, descriptive and contextual research design where twenty students volunteered to take part in the study by signing an informed consent was followed. Descriptive naïve sketches were used for data collection followed by individual interviews to validate the findings. Data was analysed by means of the descriptive method of open coding of Tesch (in Creswell, 1994:155. DENOSA’s ethical standards for research (1998:7 were considered.

Influence of Meibomian Gland Expression Methods on Human Lipid Analysis Results.

Science.gov (United States)

Kunnen, Carolina M E; Brown, Simon H J; Lazon de la Jara, Percy; Holden, Brien A; Blanksby, Stephen J; Mitchell, Todd W; Papas, Eric B

2016-01-01

To compare the lipid composition of human meibum across three different meibum expression techniques. Meibum was collected from five healthy non-contact lens wearers (aged 20-35 years) after cleaning the eyelid margin using three meibum expression methods: cotton buds (CB), meibomian gland evaluator (MGE) and meibomian gland forceps (MGF). Meibum was also collected using cotton buds without cleaning the eyelid margin (CBn). Lipids were analyzed by chip-based, nano-electrospray mass spectrometry (ESI-MS). Comparisons were made using linear mixed models. Tandem MS enabled identification and quantification of over 200 lipid species across ten lipid classes. There were significant differences between collection techniques in the relative quantities of polar lipids obtained (P<.05). The MGE method returned smaller polar lipid quantities than the CB approaches. No significant differences were found between techniques for nonpolar lipids. No significant differences were found between cleaned and non-cleaned eyelids for polar or nonpolar lipids. Meibum expression technique influences the relative amount of phospholipids in the resulting sample. The highest amounts of phospholipids were detected with the CB approaches and the lowest with the MGE technique. Cleaning the eyelid margin prior to expression was not found to affect the lipid composition of the sample. This may be a consequence of the more forceful expression resulting in cell membrane contamination or higher risk of tear lipid contamination as a result of reflex tearing. Copyright © 2016 Elsevier Inc. All rights reserved.

New test methods for BIPV. Results from IP performance

International Nuclear Information System (INIS)

Jol, J.C.; Van Kampen, B.J.M.; De Boer, B.J.; Reil, F.; Geyer, D.

2009-11-01

Within the Performance project new test procedures for PV building products and the building performance as a whole when PV is applied in buildings have been drafted. It has resulted in a first draft of new test procedures for PV building products and proposals for tests for novel BIPV technology like thin film. The test proposed are a module breakage test for BIPV products, a fire safety test for BIPV products and a dynamic load test for BIPV products. Furthermore first proposals of how flexible PV modules could be tested in an appropriate way to ensure long time quality and safety of these new products are presented.

Diamagnetic measurements on ISX-B: method and results

International Nuclear Information System (INIS)

Neilson, G.H.

1983-10-01

A diamagnetic loop is used on the ISX-B tokamak to measure the change in toroidal magnetic flux, sigma phi, caused by finite plasma current and perpendicular pressure. From this measurement, the perpendicular poloidal beta β/sub I perpendicular to/ is determined. The principal difficulty encountered is in identifying and making corrections for various noise components which appear in the measured flux. These result from coupling between the measuring loops and the toroidal and poloidal field windings, both directly and through currents induced in the vacuum vessel and coils themselves. An analysis of these couplings is made and techniques for correcting them developed. Results from the diamagnetic measurement, employing some of these correction techniques, are presented and compared with other data. The obtained values of β/sub I perpendicular to/ agree with those obtained from the equilibrium magnetic analysis (β/sub IΔ/) in ohmically heated plasmas, indicating no anisotropy. However, with 0.3 to 2.0 MW of tangential neutral beam injection, β/sub IΔ/ is consistently greater than β/sub I pependicular to/ and qualitatively consistent with the formation of an anisotropic ion velocity distribution and with toroidal rotation. Quantitatively, the difference between β/sub IΔ/ and β/sub I perpendicular to/ is more than can be accounted for on the basis of the usual classical fast ion calculations and spectroscopic rotation measurements

Validation of an analytical method for the determination of aldehydes and acetone present in the ambient air at the metropolitan area of Costa Rica

International Nuclear Information System (INIS)

Rojas Marin, Jose Felix

2010-01-01

The analytical method validation has been conducted for the simultaneous determination of 15 carbonyl compounds, the main aldehydes and ketones present in ambient air. The compounds have been captured on cartridges packed with silica gel impregnated with 2.4-dinitrophenylhydrazine (DNPH) at a constant flow of about 1 lmin -1 . Carbonyl compounds present have formed the respective products, which are then eluted with acetonitrile (solid phase extraction). The extracts were analyzed by the technique of high resolution liquid chromatography with ultraviolet detector at a wavelength of 360 nm. The following results were obtained during method validation: linearity from 0.03 mgl -1 to 15 mgl -1 , limits of detection and quantification of 0.02 mgl -1 and 0.06 mgl -1 , the accuracy no significant bias at a confidence level of 95%, accuracy for repeatability and producibility of the analytical method are around 1%. Two sampling campaigns were made in dry and rainy seasons of 2009 for areas of San Jose, Heredia and Belen. The predominant compounds were found to be acetone, acetaldehyde and the formaldehyde was the most abundant in the city of San Jose, others do not have significant amounts, so there is strong correlation between formaldehyde and acetaldehyde suggesting that stem from a common source, possibly vehicle emissions. (author) [es

An assessment of the validity of inelastic design analysis methods by comparisons of predictions with test results

International Nuclear Information System (INIS)

Corum, J.M.; Clinard, J.A.; Sartory, W.K.

1976-01-01

The use of computer programs that employ relatively complex constitutive theories and analysis procedures to perform inelastic design calculations on fast reactor system components introduces questions of validation and acceptance of the analysis results. We may ask ourselves, ''How valid are the answers.'' These questions, in turn, involve the concepts of verification of computer programs as well as qualification of the computer programs and of the underlying constitutive theories and analysis procedures. This paper addresses the latter - the qualification of the analysis methods for inelastic design calculations. Some of the work underway in the United States to provide the necessary information to evaluate inelastic analysis methods and computer programs is described, and typical comparisons of analysis predictions with inelastic structural test results are presented. It is emphasized throughout that rather than asking ourselves how valid, or correct, are the analytical predictions, we might more properly question whether or not the combination of the predictions and the associated high-temperature design criteria leads to an acceptable level of structural integrity. It is believed that in this context the analysis predictions are generally valid, even though exact correlations between predictions and actual behavior are not obtained and cannot be expected. Final judgment, however, must be reserved for the design analyst in each specific case. (author)

Presentation Attack Detection for Iris Recognition System Using NIR Camera Sensor

Science.gov (United States)

Nguyen, Dat Tien; Baek, Na Rae; Pham, Tuyen Danh; Park, Kang Ryoung

2018-01-01

Among biometric recognition systems such as fingerprint, finger-vein, or face, the iris recognition system has proven to be effective for achieving a high recognition accuracy and security level. However, several recent studies have indicated that an iris recognition system can be fooled by using presentation attack images that are recaptured using high-quality printed images or by contact lenses with printed iris patterns. As a result, this potential threat can reduce the security level of an iris recognition system. In this study, we propose a new presentation attack detection (PAD) method for an iris recognition system (iPAD) using a near infrared light (NIR) camera image. To detect presentation attack images, we first localized the iris region of the input iris image using circular edge detection (CED). Based on the result of iris localization, we extracted the image features using deep learning-based and handcrafted-based methods. The input iris images were then classified into real and presentation attack categories using support vector machines (SVM). Through extensive experiments with two public datasets, we show that our proposed method effectively solves the iris recognition presentation attack detection problem and produces detection accuracy superior to previous studies. PMID:29695113

Presentation Attack Detection for Iris Recognition System Using NIR Camera Sensor

Directory of Open Access Journals (Sweden)

Dat Tien Nguyen

2018-04-01

Full Text Available Among biometric recognition systems such as fingerprint, finger-vein, or face, the iris recognition system has proven to be effective for achieving a high recognition accuracy and security level. However, several recent studies have indicated that an iris recognition system can be fooled by using presentation attack images that are recaptured using high-quality printed images or by contact lenses with printed iris patterns. As a result, this potential threat can reduce the security level of an iris recognition system. In this study, we propose a new presentation attack detection (PAD method for an iris recognition system (iPAD using a near infrared light (NIR camera image. To detect presentation attack images, we first localized the iris region of the input iris image using circular edge detection (CED. Based on the result of iris localization, we extracted the image features using deep learning-based and handcrafted-based methods. The input iris images were then classified into real and presentation attack categories using support vector machines (SVM. Through extensive experiments with two public datasets, we show that our proposed method effectively solves the iris recognition presentation attack detection problem and produces detection accuracy superior to previous studies.

Presentation Attack Detection for Iris Recognition System Using NIR Camera Sensor.

Science.gov (United States)

Nguyen, Dat Tien; Baek, Na Rae; Pham, Tuyen Danh; Park, Kang Ryoung

2018-04-24

Among biometric recognition systems such as fingerprint, finger-vein, or face, the iris recognition system has proven to be effective for achieving a high recognition accuracy and security level. However, several recent studies have indicated that an iris recognition system can be fooled by using presentation attack images that are recaptured using high-quality printed images or by contact lenses with printed iris patterns. As a result, this potential threat can reduce the security level of an iris recognition system. In this study, we propose a new presentation attack detection (PAD) method for an iris recognition system (iPAD) using a near infrared light (NIR) camera image. To detect presentation attack images, we first localized the iris region of the input iris image using circular edge detection (CED). Based on the result of iris localization, we extracted the image features using deep learning-based and handcrafted-based methods. The input iris images were then classified into real and presentation attack categories using support vector machines (SVM). Through extensive experiments with two public datasets, we show that our proposed method effectively solves the iris recognition presentation attack detection problem and produces detection accuracy superior to previous studies.

Review of recent irradiation-creep results

International Nuclear Information System (INIS)

Coghlan, W.A.

1982-05-01

Materials deform faster under stress in the presence of irradiation by a process known as irradiation creep. This phenomenon is important to reactor design and has been the subject of a large number of experimental and theoretical investigations. The purpose of this work is to review the recent experimental results to obtain a summary of these results and to determine those research areas that require additional information. The investigations have been classified into four subgroups based on the different experimental methods used. These four are: (1) irradiation creep using stress relaxation methods, (2) creep measurements using pressurized tubes, (3) irradiation creep from constant applied load, and (4) irradiation creep experiments using accelerated particles. The similarity and the differences of the results from these methods are discussed and a summary of important results and suggested areas for research is presented. In brief, the important results relate to the dependence of creep on swelling, temperature, stress state and alloying additions. In each of these areas new results have been presented and new questions have arisen which require further research to answer. 65 references

Combining traditional dietary assessment methods with novel metabolomics techniques: present efforts by the Food Biomarker Alliance

DEFF Research Database (Denmark)

Brouwer-Brolsma, Elske M; Brennan, Lorraine; Drevon, Christian A

2017-01-01

food metabolomics techniques that allow the quantification of up to thousands of metabolites simultaneously, which may be applied in intervention and observational studies. As biomarkers are often influenced by various other factors than the food under investigation, FoodBAll developed a food intake...... in these metabolomics studies, knowledge about available electronic metabolomics resources is necessary and further developments of these resources are essential. Ultimately, present efforts in this research area aim to advance quality control of traditional dietary assessment methods, advance compliance evaluation...

Method for a national tariff comparison for natural gas, electricity and heat. Set-up and presentation

International Nuclear Information System (INIS)

1998-05-01

Several groups (within distribution companies and outside those companies) have a need for information and data on energy tariffs. It is the opinion of the ad-hoc working group that a comparison of tariffs on the basis of standard cases is the most practical method to meet the information demand of all the parties involved. Those standard cases are formulated and presented for prices of electricity, natural gas and heat, including applied consumption parameters. A comparison of such tariffs must be made periodically

3D MRI of the colon: methods and first results of 5 patients

International Nuclear Information System (INIS)

Luboldt, W.; Bauerfeind, P.; Pelkonen, P.; Steiner, P.; Krestin, G.P.; Debatin, J.F.

1997-01-01

Purpose: 'Exoscopic' and endoscopic identification of colorectal pathologies via MRI. Methods: 5 patients (36-88 years), two normal and three with different colorectal pathologies (diverticular disease, polyps and carcinoma of the colon), were examined by MRI after colonoscopy. Subsequent to filling of the colon with a gadolinium-water mixture under MRI-monitoring, 3D-data sets of the colon were acquired in prone and supine positions over a 28 sec breathold interval. Subsequently multiplanar T 1 -weighted 2D-sequences were acquired before and following i.v. administration of Gd-DTPA (0.1 mmol/kg BW). All imaging was performed in the coronal orientation. The 3D-data were interactively analysed based on various displays: Maximum intensity projection (MIP), surface shadowed display (SSD), multiplanar reconstruction (MPR), virtual colonoscopy (VC). Results: All of the colorectal pathologies could be interactively diagnosed by MPR. On MIP images some pathologies were missed. VC presented the morphology of colon haustra as well as of all endoluminally growing lesions in a manner similar to endoscopy. The colon masses showed uptake of contrast media and could thus be differentiated from air or faeces. (orig./AJ) [de

Comparative analysis of different methods of extraction of present hydrocarbons in industrial residual waters

International Nuclear Information System (INIS)

Santa, Judith Rocio; Serrano, Martin; Stashenko, Elena

2002-01-01

A comparison among four extraction techniques such as: liquid - liquid (LLE) continuous and for lots, solid phase extraction (SPE), solid phase micro extraction (SPME) and static headspace (S-HS) was carried out. The main purpose of this research was to determine the highest recovery efficiencies and how reproducible the tests are while varying parameters such as time, extraction technique, type of solvents and others. Chromatographic parameters were optimized in order to carry out the analyses. Hydrocarbon's quantification of residual waters was achieved by using a high-resolution gas chromatography with a gas flame ionization detector (HRGC-FID). Validation of the method was carried out by analyzing real samples taken in different sampling places of the residual waters treatment plant of Ecopetrol - Barrancabermeja. The use of extraction methods that require big solvent quantities and long time for analysis are losing validity day by day. Techniques such as the HS-SPME and static HS are offered as alternatives for quantifying hydrocarbons. They show total lack of solvents, high sensibility, selectivity and the techniques are reproducible. Solid phase micro extraction (SPME) and static headspace (static HS) techniques were chosen as the extraction techniques to validate the method in real samples. Both techniques showed similar results for the determination of total hydrocarbons (in the gasoline range)

Clinical Presentation of Epilepsy among Adult Sudanese Epileptic ...

African Journals Online (AJOL)

Objective: To study the pattern of clinical presentation of epilepsy among adult Sudanese epileptic patients. Methods: 120 patients with epilepsy were included in a prospective cross-sectional study. Setting: The study was conducted at Sheik Mohamed Kheir Friday Epileptic Clinic .Duration: May 2003 Oct 2006. Results: ...

Features of theYounger Schoolboys’ Attitude to the Fine Works of Art Presented at the Reproduction and Computer Presentations

Directory of Open Access Journals (Sweden)

Eremeev M.A.,

2017-01-01

Full Text Available There is an issue, which is connected with the active using of multimedia technology in education, including art. The question of the effectiveness of the production computer presentation as compared with the traditional method of production in getting acquainted students with the works of art. It is presented a study, which is aimed to analyze the differences in the perception of junior school children works of art, depending on the format of presentation (reproduction, the electronic form. It is explained a special designed method for this study, called "Talk about your impressions". There were 60 students, of the second grade progymnasium number 1756, who were involved in this study. The method "Talk about your impressions" is used to identify differences in the perception of works of art, depending on the presentation format. In order to identify the differences in the understanding of the subjects of figurative content of the picture, depending on the development of imaginative and logical thinking, and the stability and concentration following methods were used: Test Toulouse-Pieroni, Raven Progressive Matrices, the method of semantic differential Charles Osgood (modification of Guruzhapova V.A.. The results showed that the vast majority of the subjects in the comparison of the situation identical pictures, but in different formats (reproduction, electronic format prefer reproduction. It is shown that the understanding of a holistic way of painting subjects are not related to the format requirements of the pictures. It was found that the difference in the understanding of younger schoolboys figurative content of the picture does not dependent on the development of imaginative or logical thinking, and on the stability and concentration. This work was performed by grant of Davydov V. V.

A Convergence Result for the Euler-Maruyama Method for a Simple Stochastic Differential Equation with Discontinuous Drift

DEFF Research Database (Denmark)

Simonsen, Maria; Schiøler, Henrik; Leth, John-Josef

2014-01-01

The Euler-Maruyama method is applied to a simple stochastic differential equation (SDE) with discontinuous drift. Convergence aspects are investigated in the case, where the Euler-Maruyama method is simulated in dyadic points. A strong rate of convergence is presented for the numerical simulations...

Creating an effective poster presentation.

Science.gov (United States)

Taggart, H M; Arslanian, C

2000-01-01

One way to build knowledge in nursing is to share research findings or clinical program outcomes. The dissemination of these findings is often a difficult final step in a project that has taken months or years to complete. One method of sharing findings in a relaxed and informal setting is a poster presentation. This method is an effective form for presenting findings using an interactive approach. The milieu of a poster presentation enables the presenters to interact and dialogue with colleagues. Guidelines for size and format require that the poster is clear and informative. Application of design helps to create visually appealing posters. This article summarizes elements of designing and conducting a poster presentation.

Attention shifts the language network reflecting paradigm presentation

Directory of Open Access Journals (Sweden)

Kathrin eKollndorfer

2013-11-01

Full Text Available Objectives: Functional magnetic resonance imaging (fMRI is a reliable and non-invasive method with which to localize language function in pre-surgical planning. In clinical practice, visual stimulus presentation is often difficult or impossible, due to the patient’s restricted language or attention abilities. Therefore, our aim was to investigate modality-specific differences in visual and auditory stimulus presentation.Methods: Ten healthy subjects participated in an fMRI study comprising two experiments with visual and auditory stimulus presentation. In both experiments, two language paradigms (one for language comprehension and one for language production used in clinical practice were investigated. In addition to standard data analysis by the means of the general linear model (GLM, independent component analysis (ICA was performed to achieve more detailed information on language processing networks.Results: GLM analysis revealed modality-specific brain activation for both language paradigms for the contrast visual > auditory in the area of the intraparietal sulcus and the hippocampus, two areas related to attention and working memory. Using group ICA, a language network was detected for both paradigms independent of stimulus presentation modality. The investigation of language lateralization revealed no significant variations. Visually presented stimuli further activated an attention-shift network, which could not be identified for the auditory presented language.Conclusion: The results of this study indicate that the visually presented language stimuli additionally activate an attention-shift network. These findings will provide important information for pre-surgical planning in order to preserve reading abilities after brain surgery, significantly improving surgical outcomes. Our findings suggest that the presentation modality for language paradigms should be adapted on behalf of individual indication.

Present and future position of neutron activation analysis

International Nuclear Information System (INIS)

de Bruin, M.

1992-01-01

Results are presented of the performance of INAA and RNAA and when compared with other spectrometric methods for trace element analysis. Indications are given for further developments aiming at exploiting the advantage and reducing the drawbacks of these two analysis technique. (author) 12 refs.; 2 figs.; 1 tab

Correction the Bias of Odds Ratio resulting from the Misclassification of Exposures in the Study of Environmental Risk Factors of Lung Cancer using Bayesian Methods

Directory of Open Access Journals (Sweden)

Alireza Abadi

2015-07-01

Full Text Available Background & Objective: Inability to measure exact exposure in epidemiological studies is a common problem in many studies, especially cross-sectional studies. Depending on the extent of misclassification, results may be affected. Existing methods for solving this problem require a lot of time and money and it is not practical for some of the exposures. Recently, new methods have been proposed in 1:1 matched case–control studies that have solved these problems to some extent. In the present study we have aimed to extend the existing Bayesian method to adjust for misclassification in matched case–control Studies with 1:2 matching. Methods: Here, the standard Dirichlet prior distribution for a multinomial model was extended to allow the data of exposure–disease (OR parameter to be imported into the model excluding other parameters. Information that exist in literature about association between exposure and disease were used as prior information about OR. In order to correct the misclassification Sensitivity Analysis was accomplished and the results were obtained under three Bayesian Methods. Results: The results of naïve Bayesian model were similar to the classic model. The second Bayesian model by employing prior information about the OR, was heavily affected by these information. The third proposed model provides maximum bias adjustment for the risk of heavy metals, smoking and drug abuse. This model showed that heavy metals are not an important risk factor although raw model (logistic regression Classic detected this exposure as an influencing factor on the incidence of lung cancer. Sensitivity analysis showed that third model is robust regarding to different levels of Sensitivity and Specificity. Conclusion: The present study showed that although in most of exposures the results of the second and third model were similar but the proposed model would be able to correct the misclassification to some extent.

Application of Statistical Methods to Activation Analytical Results near the Limit of Detection

DEFF Research Database (Denmark)

Heydorn, Kaj; Wanscher, B.

1978-01-01

Reporting actual numbers instead of upper limits for analytical results at or below the detection limit may produce reliable data when these numbers are subjected to appropriate statistical processing. Particularly in radiometric methods, such as activation analysis, where individual standard...... deviations of analytical results may be estimated, improved discrimination may be based on the Analysis of Precision. Actual experimental results from a study of the concentrations of arsenic in human skin demonstrate the power of this principle....

Past Results, Present Trends, and Future Challenges in Intrabody Communication

Directory of Open Access Journals (Sweden)

David Naranjo-Hernández

2018-01-01

Full Text Available Intrabody communication (IBC is a wireless communication technology using the human body to develop body area networks (BANs for remote and ubiquitous monitoring. IBC uses living tissues as a transmission medium, achieving power-saving and miniaturized transceivers, making communications more robust against external interference and attacks on the privacy of transmitted data. Due to these advantages, IBC has been included as a third physical layer in the IEEE 802.15.6 standard for wireless body area networks (WBANs designated as Human Body Communication (HBC. Further research is needed to compare both methods depending on the characteristics of IBC application. Challenges remain for an optimal deployment of IBC technology, such as the effect of long-term use in the human body, communication optimization through more realistic models, the influence of both anthropometric characteristics and the subject’s movement on the transmission performance, standardization of communications, and development of small-size and energy-efficient prototypes with increased data rate. The purpose of this work is to provide an in-depth overview of recent advances and future challenges in human body/intrabody communication for wireless communications and mobile computing.

Voting Present

Directory of Open Access Journals (Sweden)

James Lo

2013-12-01

Full Text Available During his time as a state senator in Illinois, Barack Obama voted “Present” 129 times, a deliberate act of nonvoting that subsequently became an important campaign issue during the 2008 presidential elections. In this article, I examine the use of Present votes in the Illinois state senate. I find evidence that Present votes can largely be characterized as protest votes used as a legislative tool by the minority party. Incorporating information from Present votes into a Bayesian polytomous item-response model, I find that this information increases the efficiency of ideal point estimates by approximately 35%. There is little evidence of significant moderation by Obama when Present votes are accounted for, though my results suggest that Obama’s voting record may have moderated significantly before his subsequent election to the U.S. Senate. My results also suggest that because legislative nonvoting may occur for a variety of reasons, naive inclusion of nonvoting behavior into vote choice models may lead to biased results.

Presentation of some methods for the solution of the monoenergetic neutrons transport equation

International Nuclear Information System (INIS)

Valle G, E. del.

1978-01-01

The neutrons transport theory problems whose solution has been reached were collected in order to show that the transport equation is so complicated that different techniques were developed so as to give approximative numerical solutions to problems concerning the practical application. Such a technique, which had not been investigated in the literature dealing with these problems, is described here. The results which were obtained through this technique in undimensional problems of criticity are satisfactory and speaking in a conceptual way this method is extremely simple because it times. There is no limitation to deal with problems related neutrons sources with an arbitrary distribution and in principle the application of this technique can be extended to unhomogeneous environments. (author)

Multirapid Serial Visual Presentation Framework for EEG-Based Target Detection

Directory of Open Access Journals (Sweden)

Zhimin Lin

2017-01-01

Full Text Available Target image detection based on a rapid serial visual presentation (RSVP paradigm is a typical brain-computer interface system with various applications, such as image retrieval. In an RSVP paradigm, a P300 component is detected to determine target images. This strategy requires high-precision single-trial P300 detection methods. However, the performance of single-trial detection methods is relatively lower than that of multitrial P300 detection methods. Image retrieval based on multitrial P300 is a new research direction. In this paper, we propose a triple-RSVP paradigm with three images being presented simultaneously and a target image appearing three times. Thus, multitrial P300 classification methods can be used to improve detection accuracy. In this study, these mechanisms were extended and validated, and the characteristics of the multi-RSVP framework were further explored. Two different P300 detection algorithms were also utilized in multi-RSVP to demonstrate that the scheme is universally applicable. Results revealed that the detection accuracy of the multi-RSVP paradigm was higher than that of the standard RSVP paradigm. The results validate the effectiveness of the proposed method, and this method can provide a whole new idea in the field of EEG-based target detection.

Present municipal water treatment and potential removal methods

International Nuclear Information System (INIS)

Lee, S.Y.; White, S.K.; Bondietti, E.A.

1982-01-01

Uranium analyses of raw water, intermediate stage, and treated water samples from 20 municipal water treatment plants indicated that the present treatment practices were not effective in removing uranium from raw waters when the influent concentration was in the range of 0.1 to 16 μg/L uranium. Laboratory batch tests revealed that the water softening and coagulant chemicals commonly used were able to remove more than 90% of the dissolved uranium ( < 100 μg/L) in waters if an optimum pH and dosage were provided. Absorbents, titanium oxide and activated charcoal, were also effective in uranium removal under specific conditions. Strong base anion exchange resin was the most efficient uranium adsorbent, and an anion exchange column is a recommended option for the treatment of private well waters containing uranium at higher than desirable levels

Prediction-error identification of LPV systems : present and beyond

NARCIS (Netherlands)

Toth, R.; Heuberger, P.S.C.; Hof, Van den P.M.J.; Mohammadpour, J.; Scherer, C. W.

2012-01-01

The proposed chapter aims at presenting a unified framework of prediction-error based identification of LPV systems using freshly developed theoretical results. Recently, these methods have got a considerable attention as they have certain advantages in terms of computational complexity, optimality

Natural Attenuation of Chlorinated Solvents Performance and Cost Results from Multiple Air Force Demonstration Sites, Technology Demonstration Slide Presentation

National Research Council Canada - National Science Library

Wiedemeier, Todd

1999-01-01

This slide presentation summarizes the results of natural attenuation treatability studies at 14 Air Force sites contaminated with chlorinated solvents and their associated biodegradation daughter products...

Comments on the present state and future directions of PDF methods

Science.gov (United States)

Obrien, E. E.

1992-01-01

The one point probability density function (PDF) method is examined in light of its use in actual engineering problems. The PDF method, although relatively complicated, appears to be the only format available to handle the nonlinear stochastic difficulties caused by typical reaction kinetics. Turbulence modeling, if it is to play a central role in combustion modeling, has to be integrated with the chemistry in a way which produces accurate numerical solutions to combustion problems. It is questionable whether the development of turbulent models in isolation from the peculiar statistics of reactant concentrations is a fruitful line of development as far as propulsion is concerned. There are three issues for which additional viewgraphs are prepared: the one point pdf method; the amplitude mapping closure; and a hybrid strategy for replacing a full two point pdf treatment of reacting flows by a single point pdf and correlation functions. An appeal is made for the establishment of an adequate data base for compressible flow with reactions for Mach numbers of unity or higher.

Presenting New Grammar

Institute of Scientific and Technical Information of China (English)

WU Cai-ling; WANG Xi

2015-01-01

More and more researchers have now agreed upon the necessity of teaching grammar, but it still remains controversial as how to teach the forms, with the central consideration of not to harm the meaning-focused communicative teaching method. In this essay, one of the issues in grammar teaching will be discussed as how to present new grammar to learners, through evaluating and modifying a particular presentation activity in a grammar-teaching textbook.

Evaluation and presentation of analysis methods for reception analysis in reprocessing

International Nuclear Information System (INIS)

Mainka, E.

1985-01-01

The fissile material content in the dissolving or balancing tank of a reprocessing plant has special significance in nuclear fuel balancing. This is the first opportunity for destructive analysis of the fuel content of the material after burn-up of fuel elements in the reactor. In the current state-of-the-art, all balancing methods are based directly or indirectly on data obtained by chemical analysis. The following methods are evaluated: Mass-spectroscopic isotope dilution analysis, X-ray fluorescence spectroscopy, Isotopic correlation, Gamma absorptiometry, Redox titration, Emission spectroscopy after plasma excitation, Alpha spectroscopy, and Laser Raman spectroscopy

On Calculation Methods and Results for Straight Cylindrical Roller Bearing Deflection, Stiffness, and Stress

Science.gov (United States)

Krantz, Timothy L.

2011-01-01

The purpose of this study was to assess some calculation methods for quantifying the relationships of bearing geometry, material properties, load, deflection, stiffness, and stress. The scope of the work was limited to two-dimensional modeling of straight cylindrical roller bearings. Preparations for studies of dynamic response of bearings with damaged surfaces motivated this work. Studies were selected to exercise and build confidence in the numerical tools. Three calculation methods were used in this work. Two of the methods were numerical solutions of the Hertz contact approach. The third method used was a combined finite element surface integral method. Example calculations were done for a single roller loaded between an inner and outer raceway for code verification. Next, a bearing with 13 rollers and all-steel construction was used as an example to do additional code verification, including an assessment of the leading order of accuracy of the finite element and surface integral method. Results from that study show that the method is at least first-order accurate. Those results also show that the contact grid refinement has a more significant influence on precision as compared to the finite element grid refinement. To explore the influence of material properties, the 13-roller bearing was modeled as made from Nitinol 60, a material with very different properties from steel and showing some potential for bearing applications. The codes were exercised to compare contact areas and stress levels for steel and Nitinol 60 bearings operating at equivalent power density. As a step toward modeling the dynamic response of bearings having surface damage, static analyses were completed to simulate a bearing with a spall or similar damage.

Innovative presentations for dummies

CERN Document Server

Anthony, Ray

2014-01-01

Be the speaker they follow with breakthrough innovative presentations Innovative Presentations For Dummies is a practical guide to engaging your audience with superior, creative, and ultra-compelling presentations. Using clear language and a concise style, this book goes way beyond PowerPoint to enable you to reimagine, reinvent, and remake your presentations. Learn how to stimulate, capture, and hold your audience in the palm of your hand with sound, sight, and touch, and get up to speed on the latest presentation design methods that make you a speaker who gets audiences committed and acting

Aircrew Exposure To Cosmic Radiation Evaluated By Means Of Several Methods; Results Obtained In 2006

International Nuclear Information System (INIS)

Ploc, Ondrej; Spurny, Frantisek; Jadrnickova, Iva; Turek, Karel

2008-01-01

Routine evaluation of aircraft crew exposure to cosmic radiation in the Czech Republic is performed by means of calculation method. Measurements onboard aircraft work as a control tool of the routine method, as well as a possibility of comparison of results measured by means of several methods. The following methods were used in 2006: (1) mobile dosimetry unit (MDU) type Liulin--a spectrometer of energy deposited in Si-detector; (2) two types of LET spectrometers based on the chemically etched track detectors (TED); (3) two types of thermoluminescent detectors; and (4) two calculation methods. MDU represents currently one of the most reliable equipments for evaluation of the aircraft crew exposure to cosmic radiation. It is an active device which measures total energy depositions (E dep ) in the semiconductor unit, and, after appropriate calibration, is able to give a separate estimation for non-neutron and neutron-like components of H*(10). This contribution consists mostly of results acquired by means of this equipment; measurements with passive detectors and calculations are mentioned because of comparison. Reasonably good agreement of all data sets could be stated

Present and future treatment possibilities in macular degeneration

Science.gov (United States)

Fisher, E.; Wegner, A.; Pfeiler, T.; Mertz, M.

2005-11-01

Purpose: To discuss present and future treatment possibilities in different types of choroidal neovascularisation. Methods: Presented are angiographic- and OCT-findings in patients with macular degeneration of different origin. Choroidal neovascularisations, which are not likely to respond positively to established procedures like thermal laser coagulation or photodynamic therapy will be discussed. Results and conclusions: Present study-guidelines and new methods of pharmacological intervention are analysed in different patterns of macular degeneration. Conventional laser coagulation in the treatment of classic, extrafoveal CNV and photodynamic therapy of predominantly classic subfoveal CNV still represent a gold standard. There are new recommendations, loosening the tight criteria of the TAP and VIP-guidelines, which cover, for instance, wider visual acuity ranges and the treatment of juxtafoveally located choroidal neovascularisations. Positive findings in literature confirm the role of PDT in pathologic myopia and other non-AMD CNV. Studies about surgical procedures, like macula- or RPE-translocation after surgical removal or thermal laser destruction of the CNV are in progress and are expected to show promising results. Phase II/III studies will soon point out the effect of anti-VEGF agents. The application of intravitreal (triamcinolone) or peribulbar (anecortave acetat) steroids could be useful. The combination with surgical or laser techniques could bring further benefit to the patient.

Comparison Of Simulation Results When Using Two Different Methods For Mold Creation In Moldflow Simulation

Directory of Open Access Journals (Sweden)

Kaushikbhai C. Parmar

2017-04-01

Full Text Available Simulation gives different results when using different methods for the same simulation. Autodesk Moldflow Simulation software provide two different facilities for creating mold for the simulation of injection molding process. Mold can be created inside the Moldflow or it can be imported as CAD file. The aim of this paper is to study the difference in the simulation results like mold temperature part temperature deflection in different direction time for the simulation and coolant temperature for this two different methods.

MULTICRITERIA METHODS IN PERFORMING COMPANIES’ RESULTS USING ELECTRONIC RECRUITING, CORPORATE COMMUNICATION AND FINANCIAL RATIOS

Directory of Open Access Journals (Sweden)

Ivana Bilić

2011-02-01

Full Text Available Human resources represent one of the most important companies’ resources responsible in creation of companies’ competitive advantage. In search for the most valuable resources, companies use different methods. Lately, one of the growing methods is electronic recruiting, not only as a recruitment tool, but also as a mean of external communication. Additionally, in the process of corporate communication, companies nowadays use the electronic corporate communication as the easiest, the cheapest and the simplest form of business communication. The aim of this paper is to investigate relationship between three groups of different criteria; including main characteristics of performed electronic recruiting, corporate communication and selected financial performances. Selected companies were ranked separately by each group of criteria by usage of multicriteria decision making method PROMETHEE II. The main idea is to research whether companies which are the highest performers by certain group of criteria obtain the similar results regarding other group of criteria or performing results.

Presentation of quantum Brownian movement in the collective coordinate method

International Nuclear Information System (INIS)

Oksak, A.I.; Sukhanov, A.D.

2003-01-01

Two explicitly solved models of quantum randomized processes described by the Langevin equation, i. e. a free quantum Brownian particle and a quantum Brownian harmonic oscillator, are considered. The Hamiltonian (string) realization of the models reveals soliton-like structure of classical solutions. Accordingly, the method of zero mode collective coordinate is an adequate means for describing the models quantum dynamics [ru

Presentations from the Aeroelastic Workshop – latest results from AeroOpt

DEFF Research Database (Denmark)

Hansen, Morten Hartvig

This report contains the slides of the presentations at the Aeroelastic Workshop held at Risø-DTU for the wind energy industry in Denmark on January 27, 2011. The scientific part of the agenda at this workshop was • Anisotropic beam element in HAWC2 for modelling of composite lay-ups (Taeseong Kim...... (Robert Mikkelsen) • Potential of fatigue and extreme load reductions on swept blades using HAWC2 (David Verelst) • Aeroelastic modal analysis of backward swept blades using HAWCStab2 (Morten H. Hansen) • Aeroelastic rotor design minimizing the loads (Christian Bak) • A small study of flat back airfoils...

Results of an interlaboratory comparison of analytical methods for contaminants of emerging concern in water.

Science.gov (United States)

Vanderford, Brett J; Drewes, Jörg E; Eaton, Andrew; Guo, Yingbo C; Haghani, Ali; Hoppe-Jones, Christiane; Schluesener, Michael P; Snyder, Shane A; Ternes, Thomas; Wood, Curtis J

2014-01-07

An evaluation of existing analytical methods used to measure contaminants of emerging concern (CECs) was performed through an interlaboratory comparison involving 25 research and commercial laboratories. In total, 52 methods were used in the single-blind study to determine method accuracy and comparability for 22 target compounds, including pharmaceuticals, personal care products, and steroid hormones, all at ng/L levels in surface and drinking water. Method biases ranged from caffeine, NP, OP, and triclosan had false positive rates >15%. In addition, some methods reported false positives for 17β-estradiol and 17α-ethynylestradiol in unspiked drinking water and deionized water, respectively, at levels higher than published predicted no-effect concentrations for these compounds in the environment. False negative rates were also generally contamination, misinterpretation of background interferences, and/or inappropriate setting of detection/quantification levels for analysis at low ng/L levels. The results of both comparisons were collectively assessed to identify parameters that resulted in the best overall method performance. Liquid chromatography-tandem mass spectrometry coupled with the calibration technique of isotope dilution were able to accurately quantify most compounds with an average bias of <10% for both matrixes. These findings suggest that this method of analysis is suitable at environmentally relevant levels for most of the compounds studied. This work underscores the need for robust, standardized analytical methods for CECs to improve data quality, increase comparability between studies, and help reduce false positive and false negative rates.

A comparison of short-term dispersion estimates resulting from various atmospheric stability classification methods

International Nuclear Information System (INIS)

Mitchell, A.E. Jr.

1982-01-01

Four methods of classifying atmospheric stability class are applied at four sites to make short-term (1-h) dispersion estimates from a ground-level source based on a model consistent with U.S. Nuclear Regulatory Commission practice. The classification methods include vertical temperature gradient, standard deviation of horizontal wind direction fluctuations (sigma theta), Pasquill-Turner, and modified sigma theta which accounts for meander. Results indicate that modified sigma theta yields reasonable dispersion estimates compared to those produced using methods of vertical temperature gradient and Pasquill-Turner, and can be considered as a potential economic alternative in establishing onsite monitoring programs. (author)

Methodics of computing the results of monitoring the exploratory gallery

Directory of Open Access Journals (Sweden)

Krúpa Víazoslav

2000-09-01

Full Text Available At building site of motorway tunnel Višòové-Dubná skala , the priority is given to driving of exploration galley that secures in detail: geologic, engineering geology, hydrogeology and geotechnics research. This research is based on gathering information for a supposed use of the full profile driving machine that would drive the motorway tunnel. From a part of the exploration gallery which is driven by the TBM method, a fulfilling information is gathered about the parameters of the driving process , those are gathered by a computer monitoring system. The system is mounted on a driving machine. This monitoring system is based on the industrial computer PC 104. It records 4 basic values of the driving process: the electromotor performance of the driving machine Voest-Alpine ATB 35HA, the speed of driving advance, the rotation speed of the disintegrating head TBM and the total head pressure. The pressure force is evaluated from the pressure in the hydraulic cylinders of the machine. Out of these values, the strength of rock mass, the angle of inner friction, etc. are mathematically calculated. These values characterize rock mass properties as their changes. To define the effectivity of the driving process, the value of specific energy and the working ability of driving head is used. The article defines the methodics of computing the gathered monitoring information, that is prepared for the driving machine Voest – Alpine ATB 35H at the Institute of Geotechnics SAS. It describes the input forms (protocols of the developed method created by an EXCEL program and shows selected samples of the graphical elaboration of the first monitoring results obtained from exploratory gallery driving process in the Višòové – Dubná skala motorway tunnel.

Testing the ISP method with the PARIO device: Accuracy of results and influence of homogenization technique

Science.gov (United States)

Durner, Wolfgang; Huber, Magdalena; Yangxu, Li; Steins, Andi; Pertassek, Thomas; Göttlein, Axel; Iden, Sascha C.; von Unold, Georg

2017-04-01

The particle-size distribution (PSD) is one of the main properties of soils. To determine the proportions of the fine fractions silt and clay, sedimentation experiments are used. Most common are the Pipette and Hydrometer method. Both need manual sampling at specific times. Both are thus time-demanding and rely on experienced operators. Durner et al. (Durner, W., S.C. Iden, and G. von Unold (2017): The integral suspension pressure method (ISP) for precise particle-size analysis by gravitational sedimentation, Water Resources Research, doi:10.1002/2016WR019830) recently developed the integral suspension method (ISP) method, which is implemented in the METER Group device PARIOTM. This new method estimates continuous PSD's from sedimentation experiments by recording the temporal evolution of the suspension pressure at a certain measurement depth in a sedimentation cylinder. It requires no manual interaction after start and thus no specialized training of the lab personnel. The aim of this study was to test the precision and accuracy of new method with a variety of materials, to answer the following research questions: (1) Are the results obtained by PARIO reliable and stable? (2) Are the results affected by the initial mixing technique to homogenize the suspension, or by the presence of sand in the experiment? (3) Are the results identical to the one that are obtained with the Pipette method as reference method? The experiments were performed with a pure quartz silt material and four real soil materials. PARIO measurements were done repetitively on the same samples in a temperature-controlled lab to characterize the repeatability of the measurements. Subsequently, the samples were investigated by the pipette method to validate the results. We found that the statistical error for silt fraction from replicate and repetitive measurements was in the range of 1% for the quartz material to 3% for soil materials. Since the sand fractions, as in any sedimentation method, must

Methods of Estimation the Reliability and Increasing the Informativeness of the Laboratory Results (Analysis of the Laboratory Case of Measurement the Indicators of Thyroid Function)

OpenAIRE

N A Kovyazina; N A Alhutova; N N Zybina; N M Kalinina

2014-01-01

The goal of the study was to demonstrate the multilevel laboratory quality management system and point at the methods of estimating the reliability and increasing the amount of information content of the laboratory results (on the example of the laboratory case). Results. The article examines the stages of laboratory quality management which has helped to estimate the reliability of the results of determining Free T3, Free T4 and TSH. The measurement results are presented by the expanded unce...

Chronic Pain in the Emergency Department: A Pilot Mixed-Methods Cross-Sectional Study Examining Patient Characteristics and Reasons for Presentations

Directory of Open Access Journals (Sweden)

Patricia A. Poulin

2016-01-01

Full Text Available Background. Chronic pain (CP accounts for 10–16% of emergency department (ED visits, contributing to ED overcrowding and leading to adverse events. Objectives. To describe patients with CP attending the ED and identify factors contributing to their visit. Methods. We used a mixed-method design combining interviews and questionnaires addressing pain, psychological distress, signs of opioid misuse, and disability. Participants were adults who attended the EDs of a large academic tertiary care center for their CP problem. Results. Fifty-eight patients (66% women; mean age 46.5, SD = 16.9 completed the study. The most frequently cited reason (60% for ED visits was inability to cope with pain. Mental health problems were common, including depression (61% and anxiety (45%. Participants had questions about the etiology of their pain, concerns about severe pain-related impairment, and problems with medication renewals or efficacy and sometimes felt invalidated in the ED. Although most participants had a primary care physician, the ED was seen as the only or best option when pain became unmanageable. Conclusions. Patients with CP visiting the ED often present with complex difficulties that cannot be addressed in the ED. Better access to interdisciplinary pain treatment is needed to reduce the burden of CP on the ED.

The review and results of different methods for facial recognition

Science.gov (United States)

Le, Yifan

2017-09-01

In recent years, facial recognition draws much attention due to its wide potential applications. As a unique technology in Biometric Identification, facial recognition represents a significant improvement since it could be operated without cooperation of people under detection. Hence, facial recognition will be taken into defense system, medical detection, human behavior understanding, etc. Several theories and methods have been established to make progress in facial recognition: (1) A novel two-stage facial landmark localization method is proposed which has more accurate facial localization effect under specific database; (2) A statistical face frontalization method is proposed which outperforms state-of-the-art methods for face landmark localization; (3) It proposes a general facial landmark detection algorithm to handle images with severe occlusion and images with large head poses; (4) There are three methods proposed on Face Alignment including shape augmented regression method, pose-indexed based multi-view method and a learning based method via regressing local binary features. The aim of this paper is to analyze previous work of different aspects in facial recognition, focusing on concrete method and performance under various databases. In addition, some improvement measures and suggestions in potential applications will be put forward.

Arsenic absorption by members of the Brassicacea family, analysed by neutron activation, k0-method - preliminary results

International Nuclear Information System (INIS)

Uemura, George; Matos, Ludmila Vieira da Silva; Silva, Maria Aparecida da; Ferreira, Alexandre Santos Martorano; Menezes, Maria Angela de Barros Correia

2009-01-01

Natural arsenic contamination is a cause for concern in many countries of the world including Argentina, Bangladesh, Chile, China, India, Mexico, Thailand and the United States of America and also in Brazil, specially in the Iron Quadrangle area, where mining activities has been contributing to aggravate natural contamination. Brassicacea is a plant family with edible species (arugula, cabbage, cauliflower, cress, kale, mustard, radish), ornamental ones (alysssum, field pennycress, ornamental cabbages and kales) and some species are known as metal and metalloid accumulators (Indian mustard, field pennycress), like chromium, nickel, and arsenic. The present work aimed at studying other taxa of the Brassicaceae family to verify their capability in absorbing arsenic, under controlled conditions, for possible utilisation in remediation activities. The analytical method chosen was neutron activation analysis, k 0 method, a routine technique at CDTN, and also very appropriate for arsenic studies. To avoid possible interference from solid substrates, like sand or vermiculite, attempts were carried out to keep the specimens in 1/4 Murashige and Skoog basal salt solution (M and S). Growth was stumped, plants withered and perished, showing that modifications in M and S had to be done. The addition of nickel and silicon allowed normal growth of the plant specimens, for periods longer than usually achieved (more than two months); yielding samples large enough for further studies with other techniques, like ICP-MS, and other targets, like speciation studies. The results of arsenic absorption are presented here and the need of nickel and silicon in the composition of M and S is discussed. (author)

Method of forecasting pollutant transfer in an aquifer initial results obtained in a sandy medium (Barp site, Gironde)

International Nuclear Information System (INIS)

Madoz-Escande, C.; Peyrus, J.-C.

1979-01-01

Hydrogeological studies are undertaken in the context of the radiological safety of nuclear plants to forecast consequences of accidental releases of radioactive pollutants into an aquifer (transfer time, concentration at points of emergence). This quantitative forecast is obtained with the aid of a mathematical model with sequential emission. This requires a knowledge of the physical parameters of the aquifer and of the behavior of the pollutant in relation to the water-bearing medium. The physical parameters of a saturated porous medium are presented with the aid of radioactive tracer tests on a model and also in the field. The initial results obtained in a sandy medium are presented. In view of the difficulty of extrapolating to field conditions the conclusions of tests on models, it was necessary to set up a mobile laboratory with which in situ studies could be undertaken. The behavior of the pollutant in relation to the water-bearing medium is the subject of preliminary laboratory research on the laws of adsorption under different pH and temperature conditions. The numerical results obtained call for confirmation in the field. A description is given of a method which should enable the distribution coefficients to be evaluated in situ

Structuring scientific works in the “Introduction, Methods, Results and Discussion” format – what a beginner ought to know

Directory of Open Access Journals (Sweden)

N. V. Avdeeva

2016-01-01

Full Text Available Reference materials about the “Introduction, Methods, Results and Discussion”, which is a commonly used international format for scientific works, have become available for Russian authors nowadays, still lack of knowledge about the format would pop up here or there, especially when we speak about beginners. The faults which would appear regularly in work structuring prompted the present research, the aim of which is to compare the information about the IMRAD format with the specific difficulties beginning authors would often face when preparing their works for publication.The main materials to be studied were sources in Russian and in English published mostly in 2010s and devoted to the problems of structuring works according to the meant above format. Besides, the present research considered the results of plagiarism tests (such tests used to be carried out at the Russia State Library within the period of 2013 – 2015 with the help of software “Automated system of specialized processing of textual documents”. The main methods of our research would remain structural and comparative analysis of texts.As a result, our research revealed the fact of inconsistency of the available information on the IMRAD structure. It would often demand deep thinking and explanations. Different authors of reference editions would as a rule differ one from another in their interpretation of the degree of necessity of this or that composition element, of the amount of details in descriptions, etc. Moreover, the very structure of scientific work looks differently for different authors. More often the structure supposes the integrity of the contents and its form, still sometimes its description would be replaced by outer elements, such as, for example, language clichés. The analysis of the most common faults in text structuring points that authors do not often have a clear idea of how to understand the different demands which are so obscurely described

(237)Np(n,f) Cross Section: New Data and Present Status

CERN Document Server

Paradela, C; Carrapico, C; Eleftheriadis, C; Leeb, H; Calvino, F; Herrera-Martinez, A; Savvidis, I; Vlachoudis, V; Haas, B; Vannini, G; Le Naour, C; Gramegna, F; Wiescher, M; Pigni, M T; Audouin, L; Mengoni, A; Quesada, J; Becvar, F; Plag, R; Cennini, P; Mosconi, M; Duran, I; Rauscher, T; Couture, A; Capote, R; Sarchiapone, L; Vlastou, R; Domingo-Pardo, C; Dillmann, I; Pavlopoulos, P; Karamanis, D; Krticka, M; Jericha, E; Ferrari, A; Martinez, T; Trubert, D; Oberhummer, H; Karadimos, D; Plompen, A; Isaev, S; Terlizzi, R; Kaeppeler, F; Cortes, G; Cox, J; Voss, F; Pretel, C; Colonna, N; Berthoumieux, E; Vaz, P; Heil, M; Lopes, I; Lampoudis, C; Walter, S; Calviani, M; Gonzalez-Romero, E; Embid-Segura, M; Stephan, C; Igashira, M; Papachristodoulou, C; Aerts, G; Tavora, L; Berthier, B; Rudolf, G; Andrzejewski, J; Villamarin, D; Ferreira-Marques, R; Tain, J L; O'Brien, S; Gunsing, F; Reifarth, R; Perrot, L; Lindote, A; Neves, F; Poch, A; Kerveno, M; Rubbia, C; Koehler, P; Dahlfors, M; Wisshak, K; Salgado, J; Dridi, W; Ventura, A; Andriamonje, S; Assimakopoulos, P; Santos, C; Ferrant, L; Lozano, M; Patronis, N; Chiaveri, E; Guerrero, C; Kadi, Y; Vicente, M C; Praena, J; Baumann, P; Oshima, M; Rullhusen, P; Furman, W; David, S; Marrone, S; Tassan-Got, L; Cano-Ott, D; Pavlix, A; Alvarez-Velarde, F; Massimi, C; Mastinu, P; Pancin, J; Papadopoulos, C; Tagliente, G; Haight, R; Chepel, V; Kossionides, E; Badurek, G; Marganiec, J; Lukic, S; Tarrio, D; Alvarez, H

2011-01-01

In this document, we present the final result obtained at the n_TOF experiment; for the neutron-induced fission cross section of the (237)Np, from the fission threshold up to 1 GeV. The method applied to get tins result is briefly discussed. n_TOF data are compared to the last experimental measurements using other TOF facilities or the surrogate method, reported experiments performed with monoenergetic sources and the FISCAL systematic, including a discussion about the existing discrepancies.

No Results? No Problem! Why We Are Publishing Methods of a Landmark Study With Results Still Pending.

Science.gov (United States)

Lacy, Brian E; Spiegel, Brennan

2017-11-01

Colorectal cancer (CRC) is the third most commonly diagnosed cancer in both men and women in the United States, and screening for CRC is a national health-care priority. In this issue, investigators from the CONFIRM study group report on the aims and study design of a large, multicenter, randomized prospective study of whether screening colonoscopy is superior to an annual fecal immunochemical test (FIT). CONFRIM hopes to enroll 50,000 individuals, aged 50-75 years, from 46 Veterans Affairs Medical Centers and monitor them for 10 years. This article is unique in that no results are presented as the study is not yet complete. We have taken this unusual step as we believe the topic of CRC screening is critically important for our readers and that the results of this massive study have the potential to change clinical practice throughout all fields of medicine.

Methods and results for stress analyses on 14-ton, thin-wall depleted UF6 cylinders

International Nuclear Information System (INIS)

Kirkpatrick, J.R.; Chung, C.K.; Frazier, J.L.; Kelley, D.K.

1996-10-01

Uranium enrichment operations at the three US gaseous diffusion plants produce depleted uranium hexafluoride (DUF 6 ) as a residential product. At the present time, the inventory of DUF 6 in this country is more than half a million tons. The inventory of DUF 6 is contained in metal storage cylinders, most of which are located at the gaseous diffusion plants. The principal objective of the project is to ensure the integrity of the cylinders to prevent causing an environmental hazard by releasing the contents of the cylinders into the atmosphere. Another objective is to maintain the cylinders in such a manner that the DUF 6 may eventually be converted to a less hazardous material for final disposition. An important task in the DUF 6 cylinders management project is determining how much corrosion of the walls can be tolerated before the cylinders are in danger of being damaged during routine handling and shipping operations. Another task is determining how to handle cylinders that have already been damaged in a manner that will minimize the chance that a breach will occur or that the size of an existing breach will be significantly increased. A number of finite element stress analysis (FESA) calculations have been done to analyze the stresses for three conditions: (1) while the cylinder is being lifted, (2) when a cylinder is resting on two cylinders under it in the customary two-tier stacking array, and (3) when a cylinder is resting on tis chocks on the ground. Various documents describe some of the results and discuss some of the methods whereby they have been obtained. The objective of the present report is to document as many of the FESA cases done at Oak Ridge for 14-ton thin-wall cylinders as possible, giving results and a description of the calculations in some detail

Decision making with consonant belief functions: Discrepancy resulting with the probability transformation method used

Directory of Open Access Journals (Sweden)

Cinicioglu Esma Nur

2014-01-01

Full Text Available Dempster−Shafer belief function theory can address a wider class of uncertainty than the standard probability theory does, and this fact appeals the researchers in operations research society for potential application areas. However, the lack of a decision theory of belief functions gives rise to the need to use the probability transformation methods for decision making. For representation of statistical evidence, the class of consonant belief functions is used which is not closed under Dempster’s rule of combination but is closed under Walley’s rule of combination. In this research, it is shown that the outcomes obtained using both Dempster’s and Walley’s rules do result in different probability distributions when pignistic transformation is used. However, when plausibility transformation is used, they do result in the same probability distribution. This result shows that the choice of the combination rule and probability transformation method may have a significant effect on decision making since it may change the choice of the decision alternative selected. This result is illustrated via an example of missile type identification.

CRIQ : An innovative measure using comparison awareness to avoid self-presentation tactics

NARCIS (Netherlands)

de Jong, Nicole; van Leeuwen, Rob G.J.; Hoekstra, Hans A.; van der Zee, Karen

2014-01-01

The article presents a new measure for career role identification, the Career Role Identification Questionnaire (CRIQ). In constructing the CRIQ, we used the Comparison Awareness Inducing Technique (CAIT), a new and innovative method to reduce the effects of self-presentation tactics. The results

CRIQ : An innovative measure using comparison awareness to avoid self-presentation tactics

NARCIS (Netherlands)

De Jong, Nicole; van Leeuwen, Rob G.J.; Hoekstra, Hans A.; van der Zee, Karen I.

The article presents a new measure for career role identification, the Career Role Identification Questionnaire (CRIQ). In constructing the CRIQ, we used the Comparison Awareness Inducing Technique (CAIT), a new and innovative method to reduce the effects of self-presentation tactics.The results

Toward the harmonization of result presentation for the eosin-5'-maleimide binding test in the diagnosis of hereditary spherocytosis.

Science.gov (United States)

Hunt, Linda; Greenwood, David; Heimpel, Hermann; Noel, Nigel; Whiteway, Alastair; King, May-Jean

2015-01-01

The eosin-5'-maleimide (EMA) Binding test measures reduced mean channel fluorescence (MCF) reading of EMA-labeled red cells (EMA-RBCs) from patients with hereditary spherocytosis (HS). Reporting test results can be either in the actual MCF reading or as a ratio by normalization of the test MCF result to the mean MCF value of six normal controls. The latter format has potential for universal reporting. We analyzed three years' archival MCF data from HS and non-HS patient groups for establishment of reference ranges of ratios for normal adults and HS. A prospective study used FC500 and FACS Canto II cytometers to analyze contemporaneously EMA-RBCs from several patient groups and normal donors. Statistical analyses of the prospective data determined the cut-off values, and the sensitivity and specificity for HS respectively for the MCF and the ratio result presentations. The effect of using fewer than six normal controls for the ratio denominator was explored. The FC500 gave a mean ratio of 0.782 (SD=0.086) in HS patients with an optimal cut-off ratio of 0.918 (98.7% specificity, 95.6% sensitivity), and gray area ratio of 0.868-0.918. The Canto II gave a mean ratio of 0.774 (SD=0.085) with an optimal cut-off ratio of 0.925 (97.1% specificity and 100% sensitivity), and gray area ratio of 0.859-0.925. Harmonization of result presentation is feasible with no apparent constraint by instrument design. Interpretation of gray-area data requires an assessment of patient's clinical presentation and family history or performing a family study. © 2014 Clinical Cytometry Society.

Collision probability method for discrete presentation of space in cylindrical cell

International Nuclear Information System (INIS)

Bosevski, T.

1969-08-01

A suitable numerical method for integration of one-group integral transport equation is obtained by series expansion of flux and neutron source by radius squared, when calculating the parameters of cylindrically symmetric reactor cell. Separation of variables in (x,y) plane enables analytical integration in one direction and efficient Gauss quadrature formula in the second direction. White boundary condition is used for determining the neutron balance. Suitable choice of spatial points distribution in the fuel and moderator condenses the procedure for determining the transport matrix and accelerates the convergence when calculating the absorption in the reactor cell. In comparison to other collision probability methods the proposed procedure is a simple mathematical model which demands smaller computer capacity and shorter computing time

Closed Versus Open Supracondylar Fractures of the Humerus in Children: A Comparison of Clinical and Radiographic Presentation and Results.

Science.gov (United States)

Lewine, Eliza; Kim, Jaehon M; Miller, Patricia E; Waters, Peter M; Mahan, Susan T; Snyder, Brian; Hedequist, Daniel; Bae, Donald S

2018-02-01

The purpose of this investigation was to compare the presentation and postoperative results of children treated for open and closed, completely displaced type III supracondylar humerus fractures (SCFs). Thirty patients with open and 66 patients with closed, completely displaced type III SCFs were evaluated. Open fractures underwent irrigation and debridement, and all patients were treated by open or closed reduction and pin fixation. Medical records were reviewed to obtain demographic information as well as preoperative and postoperative clinical data regarding mechanism of injury, neurovascular status, associated injuries, postoperative range of motion, infections, and pain. Radiographs were evaluated to quantify displacement, Baumann's angle, humeral capitellar angle, position of the anterior humeral line, and adequacy of reduction. Outcomes were assessed using Flynn criteria. Mean clinical follow-up for the open and closed fracture groups was 8.9 and 5.7 months, respectively. Both groups were similar with respect to age, sex distribution, weight and body mass index, laterality of involvement, and mechanism of injury. At presentation, 35% of closed SCFs and 23% of open SCFs presented with abnormal neurovascular status. There was a higher prevalence of diminished/absent pulses or distal limb ischemia in patients with open injuries (27%) compared with closed fractures (18%). Conversely, severely displaced closed fractures were more commonly associated with nerve injury/palsy at presentation (35%) than those with open fractures (23%). Spontaneous nerve recovery was seen in 87% within 3 to 6 months. Postoperative loss of reduction and malunion were more common in the closed fracture group. However, 84% of patients achieved good-to-excellent results by Flynn criteria, with no appreciable difference based upon open versus closed fractures. With timely wound and fracture treatment, the clinical and radiographic results of children treated for open SCFs is similar to

Present Status And First Results of the Final Focus Beam Line at the KEK Accelerator Test Facility

International Nuclear Information System (INIS)

2010-01-01

ATF2 is a final-focus test beam line which aims to focus the low emittance beam from the ATF damping ring to a vertical size of about 37 nm and to demonstrate nanometer level beam stability. Several advanced beam diagnostics and feedback tools are used. In December 2008, construction and installation were completed and beam commissioning started, supported by an international team of Asian, European, and U.S. scientists. The present status and first results are described.

Present status and first results of the final focus beam line at the KEK Accelerator Test Facility

CERN Document Server

Bambade, P; Amann, J; Angal-Kalinin, D; Apsimon, R; Araki, S; Aryshev, A; Bai, S; Bellomo, P; Bett, D; Blair, G; Bolzon, B; Boogert, S; Boorman, G; Burrows, P N; Christian, G; Coe, P; Constance, B; Delahaye, J P; Deacon, L; Elsen, E; Faus-Golfe, A; Fukuda, M; Gao, J; Geffroy, N; Gianfelice-Wendt, E; Guler, H; Hayano, H; Heo, A Y; Honda, Y; Huang, J Y; Hwang, W H; Iwashita, Y; Jeremie, A; Jones, J; Kamiya, Y; Karataev, P; Kim, E S; Kim, H S; Kim, S H; Komamiya, S; Kubo, K; Kume, T; Kuroda, S; Lam, B; Lyapin, A; Masuzawa, M; McCormick, D; Molloy, S; Naito, T; Nakamura, T; Nelson, J; Okamoto, D; Okugi, T; Oroku, M; Park, Y J; Parker, B; Paterson, E; Perry, C; Pivi, M; Raubenheimer, T; Renier, Y; Resta-Lopez, J; Rimbault, C; Ross, M; Sanuki, T; Scarfe, A; Schulte, D; Seryi, A; Spencer, C; Suehara, T; Sugahara, R; Swinson, C; Takahashi, T; Tauchi, T; Terunuma, N; Tomas, R; Urakawa, J; Urner, D; Verderi, M; Wang, M H; Warden, M; Wendt, M; White, G; Wittmer, W; Wolski, A; Woodley, M; Yamaguchi, Y; Yamanaka, T; Yan, Y; Yoda, H; Yokoya, K; Zhou, F; Zimmermann, F; 10.1103/PhysRevSTAB.13.042801

2010-01-01

ATF2 is a final-focus test beam line which aims to focus the low emittance beam from the ATF damping ring to a vertical size of about 37 nm and to demonstrate nanometer level beam stability. Several advanced beam diagnostics and feedback tools are used. In December 2008, construction and installation were completed and beam commissioning started, supported by an international team of Asian, European, and U.S. scientists. The present status and first results are described.

Sequence Similarity Presenter: a tool for the graphic display of similarities of long sequences for use in presentations.

Science.gov (United States)

Fröhlich, K U

1994-04-01

A new method for the presentation of alignments of long sequences is described. The degree of identity for the aligned sequences is averaged for sections of a fixed number of residues. The resulting values are converted to shades of gray, with white corresponding to lack of identity and black corresponding to perfect identity. A sequence alignment is represented as a bar filled with varying shades of gray. The display is compact and allows for a fast and intuitive recognition of the distribution of regions with a high similarity. It is well suited for the presentation of alignments of long sequences, e.g. of protein superfamilies, in plenary lectures. The method is implemented as a HyperCard stack for Apple Macintosh computers. Several options for the modification of the output are available (e.g. background reduction, size of the summation window, consideration of amino acid similarity, inclusion of graphic markers to indicate specific domains). The output is a PostScript file which can be printed, imported as EPS or processed further with Adobe Illustrator.

The quality of reporting methods and results of cost-effectiveness analyses in Spain: a methodological systematic review.

Science.gov (United States)

Catalá-López, Ferrán; Ridao, Manuel; Alonso-Arroyo, Adolfo; García-Altés, Anna; Cameron, Chris; González-Bermejo, Diana; Aleixandre-Benavent, Rafael; Bernal-Delgado, Enrique; Peiró, Salvador; Tabarés-Seisdedos, Rafael; Hutton, Brian

2016-01-07

Cost-effectiveness analysis has been recognized as an important tool to determine the efficiency of healthcare interventions and services. There is a need for evaluating the reporting of methods and results of cost-effectiveness analyses and establishing their validity. We describe and examine reporting characteristics of methods and results of cost-effectiveness analyses conducted in Spain during more than two decades. A methodological systematic review was conducted with the information obtained through an updated literature review in PubMed and complementary databases (e.g. Scopus, ISI Web of Science, National Health Service Economic Evaluation Database (NHS EED) and Health Technology Assessment (HTA) databases from Centre for Reviews and Dissemination (CRD), Índice Médico Español (IME) Índice Bibliográfico Español en Ciencias de la Salud (IBECS)). We identified cost-effectiveness analyses conducted in Spain that used quality-adjusted life years (QALYs) as outcome measures (period 1989-December 2014). Two reviewers independently extracted the data from each paper. The data were analysed descriptively. In total, 223 studies were included. Very few studies (10; 4.5 %) reported working from a protocol. Most studies (200; 89.7 %) were simulation models and included a median of 1000 patients. Only 105 (47.1 %) studies presented an adequate description of the characteristics of the target population. Most study interventions were categorized as therapeutic (189; 84.8 %) and nearly half (111; 49.8 %) considered an active alternative as the comparator. Effectiveness of data was derived from a single study in 87 (39.0 %) reports, and only few (40; 17.9 %) used evidence synthesis-based estimates. Few studies (42; 18.8 %) reported a full description of methods for QALY calculation. The majority of the studies (147; 65.9 %) reported that the study intervention produced "more costs and more QALYs" than the comparator. Most studies (200; 89.7 %) reported favourable

Lesion insertion in the projection domain: Methods and initial results

International Nuclear Information System (INIS)

Chen, Baiyu; Leng, Shuai; Yu, Lifeng; Yu, Zhicong; Ma, Chi; McCollough, Cynthia

2015-01-01

Purpose: To perform task-based image quality assessment in CT, it is desirable to have a large number of realistic patient images with known diagnostic truth. One effective way of achieving this objective is to create hybrid images that combine patient images with inserted lesions. Because conventional hybrid images generated in the image domain fails to reflect the impact of scan and reconstruction parameters on lesion appearance, this study explored a projection-domain approach. Methods: Lesions were segmented from patient images and forward projected to acquire lesion projections. The forward-projection geometry was designed according to a commercial CT scanner and accommodated both axial and helical modes with various focal spot movement patterns. The energy employed by the commercial CT scanner for beam hardening correction was measured and used for the forward projection. The lesion projections were inserted into patient projections decoded from commercial CT projection data. The combined projections were formatted to match those of commercial CT raw data, loaded onto a commercial CT scanner, and reconstructed to create the hybrid images. Two validations were performed. First, to validate the accuracy of the forward-projection geometry, images were reconstructed from the forward projections of a virtual ACR phantom and compared to physically acquired ACR phantom images in terms of CT number accuracy and high-contrast resolution. Second, to validate the realism of the lesion in hybrid images, liver lesions were segmented from patient images and inserted back into the same patients, each at a new location specified by a radiologist. The inserted lesions were compared to the original lesions and visually assessed for realism by two experienced radiologists in a blinded fashion. Results: For the validation of the forward-projection geometry, the images reconstructed from the forward projections of the virtual ACR phantom were consistent with the images physically

Lesion insertion in the projection domain: Methods and initial results

Energy Technology Data Exchange (ETDEWEB)

Chen, Baiyu; Leng, Shuai; Yu, Lifeng; Yu, Zhicong; Ma, Chi; McCollough, Cynthia, E-mail: mccollough.cynthia@mayo.edu [Department of Radiology, Mayo Clinic, Rochester, Minnesota 55905 (United States)

2015-12-15

Purpose: To perform task-based image quality assessment in CT, it is desirable to have a large number of realistic patient images with known diagnostic truth. One effective way of achieving this objective is to create hybrid images that combine patient images with inserted lesions. Because conventional hybrid images generated in the image domain fails to reflect the impact of scan and reconstruction parameters on lesion appearance, this study explored a projection-domain approach. Methods: Lesions were segmented from patient images and forward projected to acquire lesion projections. The forward-projection geometry was designed according to a commercial CT scanner and accommodated both axial and helical modes with various focal spot movement patterns. The energy employed by the commercial CT scanner for beam hardening correction was measured and used for the forward projection. The lesion projections were inserted into patient projections decoded from commercial CT projection data. The combined projections were formatted to match those of commercial CT raw data, loaded onto a commercial CT scanner, and reconstructed to create the hybrid images. Two validations were performed. First, to validate the accuracy of the forward-projection geometry, images were reconstructed from the forward projections of a virtual ACR phantom and compared to physically acquired ACR phantom images in terms of CT number accuracy and high-contrast resolution. Second, to validate the realism of the lesion in hybrid images, liver lesions were segmented from patient images and inserted back into the same patients, each at a new location specified by a radiologist. The inserted lesions were compared to the original lesions and visually assessed for realism by two experienced radiologists in a blinded fashion. Results: For the validation of the forward-projection geometry, the images reconstructed from the forward projections of the virtual ACR phantom were consistent with the images physically

Method for Developing Descriptions of Hard-to-Price Products: Results of the Telecommunications Product Study

Energy Technology Data Exchange (ETDEWEB)

Conrad, F.; Tonn, B.

1999-05-01

This report presents the results of a study to test a new method for developing descriptions of hard-to-price products. The Bureau of Labor Statistics (BLS) is responsible for collecting data to estimate price indices such as the Consumers Price Index (BLS) is responsible for collecting data to estimate price indices such as the Consumers Price Index (CPI). BLS accomplishes this task by sending field staff to places of business to price actual products. The field staff are given product checklists to help them determine whether products found today are comparable to products priced the previous month. Prices for non-comparable products are not included in the current month's price index calculations. A serious problem facing BLS is developing product checklists for dynamic product areas, new industries, and the service sector. It is difficult to keep checklists up-to-date and quite often simply to develop checklists for service industry products. Some people estimates that upwards of 50 % of US economic activity is not accounted for in the CPI

RESULTS OF THE QUESTIONNAIRE: ANALYSIS METHODS

CERN Multimedia

Staff Association

2014-01-01

Five-yearly review of employment conditions   Article S V 1.02 of our Staff Rules states that the CERN “Council shall periodically review and determine the financial and social conditions of the members of the personnel. These periodic reviews shall consist of a five-yearly general review of financial and social conditions;” […] “following methods […] specified in § I of Annex A 1”. Then, turning to the relevant part in Annex A 1, we read that “The purpose of the five-yearly review is to ensure that the financial and social conditions offered by the Organization allow it to recruit and retain the staff members required for the execution of its mission from all its Member States. […] these staff members must be of the highest competence and integrity.” And for the menu of such a review we have: “The five-yearly review must include basic salaries and may include any other financial or soc...

Present status and first results of the final focus beam line at the KEK Accelerator Test Facility

Directory of Open Access Journals (Sweden)

2010-04-01

Full Text Available ATF2 is a final-focus test beam line which aims to focus the low emittance beam from the ATF damping ring to a vertical size of about 37 nm and to demonstrate nanometer level beam stability. Several advanced beam diagnostics and feedback tools are used. In December 2008, construction and installation were completed and beam commissioning started, supported by an international team of Asian, European, and U.S. scientists. The present status and first results are described.

Testing the usability of the Rapid Impact Assessment Matrix (RIAM) method for comparison of EIA and SEA results

International Nuclear Information System (INIS)

Kuitunen, Markku; Jalava, Kimmo; Hirvonen, Kimmo

2008-01-01

This study examines how the results of Environmental Impact Assessment (EIA) and Strategic Environmental Assessment (SEA) could be compared using the Rapid Impact Assessment Matrix (RIAM) method. There are many tools and techniques that have been developed for use in impact assessment processes, including scoping, checklists, matrices, qualitative and quantitative models, literature reviews, and decision-support systems. While impact assessment processes have become more technically complicated, it is recognized that approaches including simpler applications of available tools and techniques are also appropriate. The Rapid Impact Assessment Matrix (RIAM) is a tool for organizing, analysing and presenting the results of a holistic EIA. RIAM was originally developed to compare the impact of alternative procedures in a single project. In this study, we used RIAM to compare the environmental and social impact of different projects, plans and programs realized within the same geographical area. RIAM scoring is based on five separate criteria. The RIAM criteria were applied to the impact that was considered to be the most significant in the evaluated cases, and scores were given both on environmental and social impact. Our results revealed that the RIAM method could be used for comparison and ranking of separate and distinct projects, plans, programs and policies, based on their negative or positive impact. Our data included 142 cases from the area of Central Finland that is covered by the Regional Council of Central Finland. This sample consisted of various types of projects, ranging from road construction to education programs that applied for EU funding

Results from the FDIRC prototype

Energy Technology Data Exchange (ETDEWEB)

Roberts, D.A., E-mail: roberts@umd.edu [University of Maryland, College Park, MD 20742 (United States); Arnaud, N. [Laboratoire de l’Accélérateur Linéaire, Centre Scientifique d’Orsay, F-91898 Orsay Cedex (France); Dey, B. [University of California, Riverside, CA 92521 (United States); Borsato, M. [Laboratoire de l’Accélérateur Linéaire, Centre Scientifique d’Orsay, F-91898 Orsay Cedex (France); Leith, D.W.G.S.; Nishimura, K.; Ratcliff, B.N. [SLAC, Stanford University, Palo Alto, CA 94309 (United States); Varner, G. [University of Hawaii, Honolulu, HI 96822 (United States); Va’vra, J. [SLAC, Stanford University, Palo Alto, CA 94309 (United States)

2014-12-01

We present results from a novel Cherenkov imaging detector called the Focusing DIRC (FDIRC). This detector was designed as a prototype of the particle identification system for the SuperB experiment, and comprises 1/12 of the SuperB barrel azimuthal coverage with partial electronics implementation. The prototype was tested in the SLAC Cosmic Ray Telescope (CRT) which provides 3-D muon tracking with an angular resolution of ∼1.5 mrad, track position resolution of 5–6 mm, start time resolution of 70 ps, and a muon low-energy cutoff of ∼2 GeV provided by an iron range stack. The quartz focusing photon camera couples to a full-size BaBar DIRC bar box and is read out by 12 Hamamatsu H8500 MaPMTs providing 768 pixels. We used IRS2 waveform digitizing electronics to read out the MaPMTs. We present several results from our on-going development activities that demonstrate that the new optics design works very well, including: (a) single photon Cherenkov angle resolutions with and without chromatic corrections, (b) S/N ratio between the Cherenkov peak and background, which consists primarily of ambiguities in possible photon paths to a given pixel, (c) dTOP=TOP{sub measured}–TOP{sub expected} resolutions, and (d) performance of the detector in the presence of high-rate backgrounds. We also describe data analysis methods and point out limits of the present performance. - Highlights: • We present results from a novel Cherenkov imaging detector called the Focusing DIRC (FDIRC). • The prototype was tested in the SLAC Cosmic Ray Telescope (CRT) which provides 3-D muon tracking. • We present several results from our on-going development activities that demonstrate that new optics design works very well. • We describe data analysis methods and point out limits of the present performance.

A novel method of S-box design based on chaotic map and composition method

International Nuclear Information System (INIS)

Lambić, Dragan

2014-01-01

Highlights: • Novel chaotic S-box generation method is presented. • Presented S-box has better cryptographic properties than other examples of chaotic S-boxes. • The advantages of the proposed method are the low complexity and large key space. -- Abstract: An efficient algorithm for obtaining random bijective S-boxes based on chaotic maps and composition method is presented. The proposed method is based on compositions of S-boxes from a fixed starting set. The sequence of the indices of starting S-boxes used is obtained by using chaotic maps. The results of performance test show that the S-box presented in this paper has good cryptographic properties. The advantages of the proposed method are the low complexity and the possibility to achieve large key space

UV-VIS Spectroscopy Applied to Stratospheric Chemistry, Methods and Results

Energy Technology Data Exchange (ETDEWEB)

Karlsen, K.

1996-03-01

This paper was read at the workshop ``The Norwegian Climate and Ozone Research Programme`` held on 11-12 March 1996. Numerous observations and modeling have shown with a very high degree of certainty that the man-made emissions of chlorofluorocarbons (CFC) and halons are responsible for the Antarctica ozone hole. It is also evident that the ozone layer of the Northern Hemisphere has suffered a certain decline over the last 10-15 years, possibly because of CFC and halons. 20-30% of the observed reduction is ascribed to coupled chlorine and bromine chemistry via a catalytic cycle resulting in the net conversion of 2O{sub 3} to 3O{sub 2}. But the details are not fully understood. The author plans to assemble a UV-VIS spectrometer for measuring the species OClO and BrO and to compare and discuss measured diurnal variations of OClO and BrO with model calculations. The use of Differential Optical Absorption Spectroscopy (DOAS) is discussed and some results from late 1995 presented. 6 refs., 2 figs.

Review of solution approach, methods, and recent results of the RELAP5 system code

International Nuclear Information System (INIS)

Trapp, J.A.; Ransom, V.H.

1983-01-01

The present RELAP5 code is based on a semi-implicit numerical scheme for the hydrodynamic model. The basic guidelines employed in the development of the semi-implicit numerical scheme are discussed and the numerical features of the scheme are illustrated by analysis for a simple, but analogous, single-equation model. The basic numerical scheme is recorded and results from several simulations are presented. The experimental results and code simulations are used in a complementary fashion to develop insights into nuclear-plant response that would not be obtained if either tool were used alone. Further analysis using the simple single-equation model is carried out to yield insights that are presently being used to implement a more-implicit multi-step scheme in the experimental version of RELAP5. The multi-step implicit scheme is also described

Method Development and Monitoring of Cyanotoxins in Water (ACS Central Presentation)

Science.gov (United States)

Increasing occurrence of cyanobacterial harmful algal blooms (HABs) in ambient waters has become a worldwide concern. Numerous cyanotoxins can be produced during HAB events which are toxic to animals and humans. Validated standardized methods that are rugged, selective and sensit...

Inverse methods for 3D quantitative optical coherence elasticity imaging (Conference Presentation)

Science.gov (United States)

Dong, Li; Wijesinghe, Philip; Hugenberg, Nicholas; Sampson, David D.; Munro, Peter R. T.; Kennedy, Brendan F.; Oberai, Assad A.

2017-02-01

In elastography, quantitative elastograms are desirable as they are system and operator independent. Such quantification also facilitates more accurate diagnosis, longitudinal studies and studies performed across multiple sites. In optical elastography (compression, surface-wave or shear-wave), quantitative elastograms are typically obtained by assuming some form of homogeneity. This simplifies data processing at the expense of smearing sharp transitions in elastic properties, and/or introducing artifacts in these regions. Recently, we proposed an inverse problem-based approach to compression OCE that does not assume homogeneity, and overcomes the drawbacks described above. In this approach, the difference between the measured and predicted displacement field is minimized by seeking the optimal distribution of elastic parameters. The predicted displacements and recovered elastic parameters together satisfy the constraint of the equations of equilibrium. This approach, which has been applied in two spatial dimensions assuming plane strain, has yielded accurate material property distributions. Here, we describe the extension of the inverse problem approach to three dimensions. In addition to the advantage of visualizing elastic properties in three dimensions, this extension eliminates the plane strain assumption and is therefore closer to the true physical state. It does, however, incur greater computational costs. We address this challenge through a modified adjoint problem, spatially adaptive grid resolution, and three-dimensional decomposition techniques. Through these techniques the inverse problem is solved on a typical desktop machine within a wall clock time of 20 hours. We present the details of the method and quantitative elasticity images of phantoms and tissue samples.

An improved method for interpreting API filter press hydraulic conductivity test results

International Nuclear Information System (INIS)

Heslin, G.M.; Baxter, D.Y.; Filz, G.M.; Davidson, R.R.

1997-01-01

The American Petroleum Institute (API) filter press is frequently used to measure the hydraulic conductivity of soil-bentonite backfill during the mix design process and as part of construction quality controls. However, interpretation of the test results is complicated by the fact that the seepage-induced consolidation pressure varies from zero at the top of the specimen to a maximum value at the bottom of the specimen. An analytical solution is available which relates the stress, compressibility, and hydraulic conductivity in soil consolidated by seepage forces. This paper presents the results of a laboratory investigation undertaken to support application of this theory to API hydraulic conductivity tests. When the API test results are interpreted using seepage consolidation theory, they are in good agreement with the results of consolidometer permeameter tests. Limitations of the API test are also discussed

Possible distortion of autoradiographic results

Energy Technology Data Exchange (ETDEWEB)

Kozlov, A.A.; Tumanushvili, G.D. (AN Gruzinskoj SSR, Tbilisi. Inst. Ehksperimental' noj Morfologii)

1980-01-01

The effect of radioactive labelling (H/sup 3/-thymidine) on the infusorian division is studied. The presented results show that introduction of labelled compounds results in accelerating infusorian cell division v. Thorough investigation of labelled compound effect with low activity on the parameters of cell division and the search of methods to eliminate distortions able to appear in autoradiographic experiments is expedient.

New Architectures for Presenting Search Results Based on Web Search Engines Users Experience

Science.gov (United States)

Martinez, F. J.; Pastor, J. A.; Rodriguez, J. V.; Lopez, Rosana; Rodriguez, J. V., Jr.

2011-01-01

Introduction: The Internet is a dynamic environment which is continuously being updated. Search engines have been, currently are and in all probability will continue to be the most popular systems in this information cosmos. Method: In this work, special attention has been paid to the series of changes made to search engines up to this point,…

Diagnostic methods for extra-temporal neocortical focal epilepsies: present and future Métodos diagnósticos das epilepsias focais neocorticais extratemporais: presente e futuro

Directory of Open Access Journals (Sweden)

Ricardo André Amorim Leite

2010-02-01

Full Text Available The progress of epilepsies diagnosis has been great, but, amongst the diagnostic detailing that demand research, one of the most important is the essential lateralization and localization of epileptogenic zone, considered as the cerebral cortex region, that removed, will result in a free state of seizures. The present study aims to analyze the possible uses of proton spectroscopy for clinical and pre-surgical evaluation of focal extratemporal epilepsies, since this group presents the highest difficulty degree for lateralizing and locating epileptogenic zones. In almost all cases, a non invasive diagnosis can be performed using routine electroencephalography, video-electroencephalography - considered as gold standard, and magnetic resonance imaging. However, when the results of these exams are contradictory, some patients need invasive techniques, as the intra-cranial video-EEG, using deep electrodes, sub-dural strip and grid, that are associated with increased diagnostic cost and risk of complications, as cerebral hemorrhages and intra-cranial infections. Proton spectroscopy appears as a possibility, given its capacity to evaluate cerebral metabolism, by N-acetyl-aspartate (NAA, creatine (Cre and choline (Cho concentrations, amongst other metabolites. This non invasive method may provide time reduction of this evaluation and reliable level improvement for this topographical diagnosis.Tem sido grande o progresso no diagnóstico das epilepsias, mas dentre os detalhamentos diagnósticos a exigir pesquisas, estão a lateralização e a localização precisas da zona epileptogênica, considerada como a região do córtex cerebral que, removida, irá resultar num estado livre de crises. Por meio de revisão da literatura, o objetivo deste estudo é expor e analisar os métodos diagnósticos das epilepsias neocorticais extratemporais, dadas as características que as tornam mais complexas do que as epilepsias temporais visto que estas apresentam o

Learning phacoemulsification. Results of different teaching methods.

Directory of Open Access Journals (Sweden)

Hennig Albrecht

2004-01-01

Full Text Available We report the learning curves of three eye surgeons converting from sutureless extracapsular cataract extraction to phacoemulsification using different teaching methods. Posterior capsule rupture (PCR as a per-operative complication and visual outcome of the first 100 operations were analysed. The PCR rate was 4% and 15% in supervised and unsupervised surgery respectively. Likewise, an uncorrected visual acuity of > or = 6/18 on the first postoperative day was seen in 62 (62% of patients and in 22 (22% in supervised and unsupervised surgery respectively.

A system and method for adjusting and presenting stereoscopic content

DEFF Research Database (Denmark)

2013-01-01

on the basis of one or more vision specific parameters (0M, ThetaMuAlphaChi, ThetaMuIotaNu, DeltaTheta) indicating abnormal vision for the user. In this way, presenting stereoscopic content is enabled that is adjusted specifically to the given person. This may e.g. be used for training purposes or for improved...

Presentation of research in anesthesia: Culmination into publication?

Directory of Open Access Journals (Sweden)

Asha Tyagi

2013-01-01

Full Text Available Background: To assess the quality of research presentations made in conferences, its success or failure to be published in a peer-reviewed journal is a well-accepted marker. However, there is no data regarding the publication of research presentations made in Indian conferences of anesthesiology. Objective: The primary objective was to determine publication rate of research presented at the largest and best attended national conference in anesthesiology, the Indian Society of Anaesthesiologists′ Conference (ISACON, and also compare it with the rate from an international conference American Society of Anesthesiologists (ASA annual meeting held in the same year. Materials and Methods: All 363 abstracts presented as poster or podium presentations at the ISACON, and an equal number of randomly selected abstracts presented at ASA annual meeting were searched on Pubmed and Google Scholar for their full-text publications in peer-reviewed journals using a standardized search strategy. As secondary observations, abstracts were assessed for completeness by noting certain components central to research methodology. Also, changes between abstract of the presentation and published paper were noted with respect to certain components. Results: The publication rate of presentations at ISACON and ASA meetings was 5% and 22%, respectively. The abstracts from ISACON lacked central components of research such as methods and statistical tests. The commonest change in the full-text publications as compared with the original abstract from both conferences was a change in authorship. Conclusion: Steps are required to augment full-text publication of Indian research, including a more rigorous peer review of abstracts submitted to ISACON to ensure their completeness.

ALICE TRD results from prototype tests

CERN Document Server

Andronic, A; Blume, C; Braun-Munzinger, P; Bucher, D; Catanescu, G; Ciobanu, M; Daues, H W; Devismes, A; Finck, C; Herrmann, N; Lister, T A; Mahmoud, Tariq; Peitzmann, Thomas; Petrovici, M; Reygers, K; Santo, R; Schicker, R; Sedykha, S; Simon, R S; Stachel, J; Stelzer, H; Wessels, J P; Winkelmann, O; Windelband, B; Xu, C

2002-01-01

We present results from tests of a prototype of the TRD for the ALICE experiment at LHC. We investigate the performance-of different radiator types, composed of foils, fibres and foams. The pion rejection performance for different methods of analysis over a momentum range from 0.7 to 2 GeV/c is presented. (8 refs).

Differential equation method

International Nuclear Information System (INIS)

Kotikov, A.V.

1993-01-01

A new method of massive Feynman diagrams calculation is presented. It provides a fairly simple procedure to obtain the result without the D-space integral calculation (for the dimensional regularization). Some diagrams are calculated as an illustration of this method capacities. (author). 7 refs

Collection and analysis of existing information on applicability of investigation methods for estimation of beginning age of faulting in present faulting pattern

International Nuclear Information System (INIS)

Doke, Ryosuke; Yasue, Ken-ichi; Tanikawa, Shin-ichi; Nakayasu, Akio; Niizato, Tadafumi; Tanaka, Takenobu; Aoki, Michinori; Sekiya, Ayako

2011-12-01

In the field of R and D programs of a geological disposal of high level radioactive waste, it is great importance to develop a set of investigation and analysis techniques for the assessment of long-term geosphere stability over a geological time, which means that any changes of geological environment will not significantly impact on the long-term safety of a geological disposal system. In Japanese archipelago, crustal movements are so active that uplift and subsidence are remarkable in recent several hundreds of thousands of years. Therefore, it is necessary to assess the long-term geosphere stability taking into account a topographic change caused by crustal movements. One of the factors for the topographic change is the movement of an active fault, which is a geological process to release a strain accumulated by plate motion. A beginning age of the faulting in the present faulting pattern suggests the beginning age of neotectonic activities around the active fault, and also provides basic information to identifying the stage of a geomorphic development of mountains. Therefore, the age of faulting in the present faulting pattern is important information to estimate a topographic change in the future on the mountain regions of Japan. In this study, existing information related to methods for the estimation of the beginning age of the faulting in the present faulting pattern on the active fault were collected and reviewed. A principle of method, noticing points and technical know-hows in the application of the methods, data uncertainty, and so on were extracted from the existing information. Based on these extracted information, task-flows indicating working process on the estimation of the beginning age for the faulting of the active fault were illustrated on each method. Additionally, the distribution map of the beginning age with accuracy of faulting in the present faulting pattern on the active fault was illustrated. (author)

Validation of a near infrared microscopy method for the detection of animal products in feedingstuffs: results of a collaborative study.

Science.gov (United States)

Boix, A; Fernández Pierna, J A; von Holst, C; Baeten, V

2012-01-01

The performance characteristics of a near infrared microscopy (NIRM) method, when applied to the detection of animal products in feedingstuffs, were determined via a collaborative study. The method delivers qualitative results in terms of the presence or absence of animal particles in feed and differentiates animal from vegetable feed ingredients on the basis of the evaluation of near infrared spectra obtained from individual particles present in the sample. The specificity ranged from 86% to 100%. The limit of detection obtained on the analysis of the sediment fraction, prepared as for the European official method, was 0.1% processed animal proteins (PAPs) in feed, since all laboratories correctly identified the positive samples. This limit has to be increased up to 2% for the analysis of samples which are not sedimented. The required sensitivity for the official control is therefore achieved in the analysis of the sediment fraction of the samples where the method can be applied for the detection of the presence of animal meal. Criteria for the classification of samples, when fewer than five spectra are found, as being of animal origin needs to be set up in order to harmonise the approach taken by the laboratories when applying NIRM for the detection of the presence of animal meal in feed.

Advances in classical and analytical mechanics: A reviews of author’s results

Directory of Open Access Journals (Sweden)

Hedrih-Stevanović Katica R.

2013-01-01

Full Text Available A review, in subjective choice, of author’s scientific results in area of: classical mechanics, analytical mechanics of discrete hereditary systems, analytical mechanics of discrete fractional order system vibrations, elastodynamics, nonlinear dynamics and hybrid system dynamics is presented. Main original author’s results were presented through the mathematical methods of mechanics with examples of applications for solving problems of mechanical real system dynamics abstracted to the theoretical models of mechanical discrete or continuum systems, as well as hybrid systems. Paper, also, presents serries of methods and scientific results authored by professors Mitropolyski, Andjelić and Rašković, as well as author’s of this paper original scientific research results obtained by methods of her professors. Vector method based on mass inertia moment vectors and corresponding deviational vector components for pole and oriented axis, defined in 1991 by K. Hedrih, is presented. Results in construction of analytical dynamics of hereditary discrete system obtained in collaboration with O. A. Gorosho are presented. Also, some selections of results author’s postgraduate students and doctorantes in area of nonlinear dynamics are presented. A list of scientific projects headed by author of this paper is presented with a list of doctoral dissertation and magister of sciences thesis which contain scientific research results obtained under the supervision by author of this paper or their fist doctoral candidates. [Projekat Ministarstva nauke Republike Srbije, br. ON174001: Dynamics of hybrid systems with complex structures

Phytotherapy: Present State of the Issue

Directory of Open Access Journals (Sweden)

L. R. Selimzianova

2016-01-01

Full Text Available Phytotherapy is one of the oldest treatment methods. Studies and conclusions of the World Health Organization (WHO Expert evidence of the trend towards greater demand for alternative treatments, including herbal medicine. The article presents such actual data on the issue under review as herbal preparations use at the present stage, frequency of and reasons for the use of medicinal plants in the world pediatric practice. There is a review of the WHO documents on quality assessment, harvesting, preparation and use of vegetable raw materials in the article. It also highlights the key provisions of the WHO strategy for ethnoscience in 2014–2023. There also is data on the properties of one of the plant-based drugs components and results of clinical trials of its effectiveness in children.

Comparison of microstickies measurement methods. Part II, Results and discussion

Science.gov (United States)

Mahendra R. Doshi; Angeles Blanco; Carlos Negro; Concepcion Monte; Gilles M. Dorris; Carlos C. Castro; Axel Hamann; R. Daniel Haynes; Carl Houtman; Karen Scallon; Hans-Joachim Putz; Hans Johansson; R. A. Venditti; K. Copeland; H.-M. Chang

2003-01-01

In part I of the article we discussed sample preparation procedure and described various methods used for the measurement of microstickies. Some of the important features of different methods are highlighted in Table 1. Temperatures used in the measurement methods vary from room temperature in some cases, 45 °C to 65 °C in other cases. Sample size ranges from as low as...

Method for visualization and presentation of priceless old prints based on precise 3D scan

Science.gov (United States)

Bunsch, Eryk; Sitnik, Robert

2014-02-01

Graphic prints and manuscripts constitute main part of the cultural heritage objects created by the most of the known civilizations. Their presentation was always a problem due to their high sensitivity to light and changes of external conditions (temperature, humidity). Today it is possible to use an advanced digitalization techniques for documentation and visualization of mentioned objects. In the situation when presentation of the original heritage object is impossible, there is a need to develop a method allowing documentation and then presentation to the audience of all the aesthetical features of the object. During the course of the project scans of several pages of one of the most valuable books in collection of Museum of Warsaw Archdiocese were performed. The book known as "Great Dürer Trilogy" consists of three series of woodcuts by the Albrecht Dürer. The measurement system used consists of a custom designed, structured light-based, high-resolution measurement head with automated digitization system mounted on the industrial robot. This device was custom built to meet conservators' requirements, especially the lack of ultraviolet or infrared radiation emission in the direction of measured object. Documentation of one page from the book requires about 380 directional measurements which constitute about 3 billion sample points. The distance between the points in the cloud is 20 μm. Provided that the measurement with MSD (measurement sampling density) of 2500 points makes it possible to show to the publicity the spatial structure of this graphics print. An important aspect is the complexity of the software environment created for data processing, in which massive data sets can be automatically processed and visualized. Very important advantage of the software which is using directly clouds of points is the possibility to manipulate freely virtual light source.

A method for assessing carbon stocks, carbon sequestration, and greenhouse-gas fluxes in ecosystems of the United States under present conditions and future scenarios

Science.gov (United States)

Bergamaschi, Brian A.; Bernknopf, Richard; Clow, David; Dye, Dennis; Faulkner, Stephen; Forney, William; Gleason, Robert; Hawbaker, Todd; Liu, Jinxun; Liu, Shu-Guang; Prisley, Stephen; Reed, Bradley; Reeves, Matthew; Rollins, Matthew; Sleeter, Benjamin; Sohl, Terry; Stackpoole, Sarah; Stehman, Stephen; Striegl, Robert G.; Wein, Anne; Zhu, Zhi-Liang; Zhu, Zhi-Liang

2010-01-01

solicited to construct these scenarios.The methods for mapping the current LULC and ecosystem disturbances will require the extensive use of both remote-sensing data and field-survey data (for example, forest inventories) to capture and characterize landscape-changing events. For potential LULC changes and ecosystem disturbances, key drivers such as socioeconomic and climate changes will be used in addition to the biophysical data. The result of these analyses will be a series of maps for each future year for each scenario. These annual maps will form the basis for estimating carbon storage and GHG emissions. For terrestrial ecosystems, carbon storage, carbon-sequestration capacities, and GHG emissions under the present conditions and future scenarios will be assessed using the LULC-change and ecosystem-disturbance estimates in map format with a spatially explicit biogeochemical ensemble modeling system that incorporates properties of management activities (such as tillage or harvesting) and properties of individual ecosystems (such as energy exchange, vegetation characteristics, hydrological cycling, and soil attributes). For aquatic ecosystems, carbon burial in sediments and fluxes of GHG are functions of the present and future potential stream flow and sediment transport and will be assessed using empirical hydrological modeling methods. Validation and uncertainty analysis methods described in the methodology will follow established guidelines to assess the quality of the assessment results.The U.S. Environmental Protection Agency’s Level II ecoregions map will be the practical instrument for developing and delivering assessment results. Consequently, the ecoregion (there are 22 modified ecoregions) will be the reporting unit of the assessment because the scenarios, assessment results, validation, and uncertainty analysis will be produced at that scale. The implementation of these methods will require collaborations among various Federal agencies, State agencies

Present state of combined wet/dry cooling in the FRG and preliminary experience with the different methods

International Nuclear Information System (INIS)

Vodicka, V.

1976-01-01

The physical reasons for the generation of the visible cooling tower plumes are explained. Today, there are several methods by which the visibility of the plumes can be suppressed. As the studies carried out show, a parallel connection of the wet and dry system on the air side is the most economical solution. Models for large-scale plants are presented, their operational performance is explained, and the cost is discussed. It is shown that wet/dry cooling is more economical than dry cooling alone, even with a relatively high proportion of dry heat discharge. (orig.) [de

Acoustic detection of particles, the RAP experiment: present status and results

International Nuclear Information System (INIS)

Bassan, M; Buonomo, B; Coccia, E; Blair, D; D'Antonio, S; Monache, G Delle; Gioacchino, D Di; Fafone, V; Ligi, C; Marini, A; Mazzitelli, G; Modestino, G; Pizzella, G; Quintieri, L; Roccella, S; Rocchi, A; Ronga, F; Tripodi, P; Valente, P

2006-01-01

Cosmic ray events with rate and energy much higher than expected were detected by the ultracryogenic gravitational antenna Nautilus located at the Laboratori Nazionali di Frascati, when it was operating in superconducting state. Mechanisms related to the superconductivity state of the material could be involved in such a way to enhance the conversion efficiency of the particle energy into vibrational energy of the detector. The RAP experiment has the aim to study the mechanical response of a small metallic resonant bar to short pulses of high energy electron beam, investigating the response of the bar both in normal and in superconducting state. The results obtained for an Al5056 bar down to a temperature of 4 K are reported and the preliminary results for a niobium bar at temperature below and above the superconducting-normal transition are also discussed

Arsenic absorption by members of the Brassicacea family, analysed by neutron activation, k{sub 0}-method - preliminary results

Energy Technology Data Exchange (ETDEWEB)

Uemura, George; Matos, Ludmila Vieira da Silva; Silva, Maria Aparecida da; Ferreira, Alexandre Santos Martorano; Menezes, Maria Angela de Barros Correia [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN-CNEN/MG), Belo Horizonte, MG (Brazil)], e-mail: george@cdtn.br, e-mail: menezes@cdtn.br

2009-07-01

Natural arsenic contamination is a cause for concern in many countries of the world including Argentina, Bangladesh, Chile, China, India, Mexico, Thailand and the United States of America and also in Brazil, specially in the Iron Quadrangle area, where mining activities has been contributing to aggravate natural contamination. Brassicacea is a plant family with edible species (arugula, cabbage, cauliflower, cress, kale, mustard, radish), ornamental ones (alysssum, field pennycress, ornamental cabbages and kales) and some species are known as metal and metalloid accumulators (Indian mustard, field pennycress), like chromium, nickel, and arsenic. The present work aimed at studying other taxa of the Brassicaceae family to verify their capability in absorbing arsenic, under controlled conditions, for possible utilisation in remediation activities. The analytical method chosen was neutron activation analysis, k{sub 0} method, a routine technique at CDTN, and also very appropriate for arsenic studies. To avoid possible interference from solid substrates, like sand or vermiculite, attempts were carried out to keep the specimens in 1/4 Murashige and Skoog basal salt solution (M and S). Growth was stumped, plants withered and perished, showing that modifications in M and S had to be done. The addition of nickel and silicon allowed normal growth of the plant specimens, for periods longer than usually achieved (more than two months); yielding samples large enough for further studies with other techniques, like ICP-MS, and other targets, like speciation studies. The results of arsenic absorption are presented here and the need of nickel and silicon in the composition of M and S is discussed. (author)

Diagnostic evaluation of patients presenting with hirsutism

Directory of Open Access Journals (Sweden)

İsmail Zeki Tekiş

2014-03-01

Full Text Available Objective: Hirsutism, similar to men, is the presence of terminal hairs in androgen-to sensitive areas in women. The present report aimed to study etiology and determine the prevalence of the diseases that causes hirsutism in these patients. Methods: In this study, total number of 40 patients who admitted because of hirsutism to Department of Endocrinology and Metabolism clinic was enrolled. Demographic, clinical and laboratory parameters of the patients were evaluated. Results: Result of the study showed that polycystic ovary syndrome is the most common cause of hirsutism. The second most common cause was found as idiopathic hirsutism. Conclusion: By the present study, etiologic factors of hirsutism were examined firstly in our region in which Ethnic and cultural diversity is concentrated. In rare cases like Cushing's syndrome, hyperprolactinemia, non-classic adrenal hyperplasia, androgen-secreting tumors should be considered in the differential diagnosis of hirsutism. J Clin Exp Invest 2014; 5 (1: 69-75

Standardization of glycohemoglobin results and reference values in whole blood studied in 103 laboratories using 20 methods.

Science.gov (United States)

Weykamp, C W; Penders, T J; Miedema, K; Muskiet, F A; van der Slik, W

1995-01-01

We investigated the effect of calibration with lyophilized calibrators on whole-blood glycohemoglobin (glyHb) results. One hundred three laboratories, using 20 different methods, determined glyHb in two lyophilized calibrators and two whole-blood samples. For whole-blood samples with low (5%) and high (9%) glyHb percentages, respectively, calibration decreased overall interlaboratory variation (CV) from 16% to 9% and from 11% to 6% and decreased intermethod variation from 14% to 6% and from 12% to 5%. Forty-seven laboratories, using 14 different methods, determined mean glyHb percentages in self-selected groups of 10 nondiabetic volunteers each. With calibration their overall mean (2SD) was 5.0% (0.5%), very close to the 5.0% (0.3%) derived from the reference method used in the Diabetes Control and Complications Trial. In both experiments the Abbott IMx and Vision showed deviating results. We conclude that, irrespective of the analytical method used, calibration enables standardization of glyHb results, reference values, and interpretation criteria.

Methods used by Elsam for monitoring precision and accuracy of analytical results

Energy Technology Data Exchange (ETDEWEB)

Hinnerskov Jensen, J [Soenderjyllands Hoejspaendingsvaerk, Faelleskemikerne, Aabenraa (Denmark)

1996-12-01

Performing round robins at regular intervals is the primary method used by ELsam for monitoring precision and accuracy of analytical results. The firs round robin was started in 1974, and today 5 round robins are running. These are focused on: boiler water and steam, lubricating oils, coal, ion chromatography and dissolved gases in transformer oils. Besides the power plant laboratories in Elsam, the participants are power plant laboratories from the rest of Denmark, industrial and commercial laboratories in Denmark, and finally foreign laboratories. The calculated standard deviations or reproducibilities are compared with acceptable values. These values originate from ISO, ASTM and the like, or from own experiences. Besides providing the laboratories with a tool to check their momentary performance, the round robins are vary suitable for evaluating systematic developments on a long term basis. By splitting up the uncertainty according to methods, sample preparation/analysis, etc., knowledge can be extracted from the round robins for use in many other situations. (au)

The clinical presentation of pulmonary embolism

International Nuclear Information System (INIS)

Otto, A.C.; Dunn, M.; Van der Merwe, B.; Katz, M.

2004-01-01

Full text: Introduction: Pulmonary embolism is often misdiagnosed by many clinicians because of confusion with pulmonary infarction. According to present literature, the latter seldomly occurs, thus pleuritic pain and hemoptysis are usually absent. The purpose of our study was to re-evaluate the clinical presentation of pulmonary embolism with specific reference to the presence of pulmonary hypertension and pulmonary infarction. Materials and methods: Ethical committee approval was obtained to study fifteen patients with abnormal lung perfusion and high probability for pulmonary embolism retrospectively. Clinical data will be presented in table format. Appropriate symptoms and signs not mentioned was considered absent. Specific investigations not available was considered not done. Results: Will be displayed in table format. The main findings can be summarized as follows: 1. Dyspnea was present in all the patients; 2. Pleuritic pain and hemoptysis was absent in all the patients; 3. None of the patients had clinical signs of pulmonary hypertension or infarction; 4. The available special investigations confirmed the above mentioned findings. Conclusion: The absence of pulmonary infarction and pulmonary hypertension with submassive pulmonary embolism (<60% of pulmonary vascular bed occluded) was reconfirmed and should be emphasized more in clinical practice. (author)

Investigating the Present Day Cosmic Dust Flux at the Earth's Surface: Initial Results from the Kwajalein Micrometeorite Collection

Science.gov (United States)

Wozniakiewicz, P. J.; Bradley, J. P.; Price, M. C.; Zolensky, M. E.; Ishii, H. A.; Brownlee, D. E.; Russell, S. S.

2014-01-01

Examination of impact craters on the Long Duration Exposure Facility satellite indicate a present day micrometeoroid flux of approx. 30,000 tonnes [1 after 2]. But what portion of this material arrives at the Earth's surface as micrometeorites? Studies of available micrometeorite collections from deep sea sediments [e.g. 3], Greenland blue ice [e.g. 4] and the South Pole water well [e.g. 1] may be complicated by terrestrial weathering and, in some cases, collection bias (magnetic separation for deep sea sediments) and poorly constrained ages. We have recently set up a micrometeorite collection station on Kwajalein Island in the Republic of the Marshall Islands in the Pacific Ocean, using high volume air samplers to collect particles directly from the atmosphere. By collecting in this way, the terrestrial age of the particles is known, the weathering they experience is minimal, and we are able to constrain particle arrival times. Collecting at this location also exploits the considerably reduced anthropogenic background [5]. Method: High volume air samplers were installed on top of the two-story airport building on Kwajalein. These were fitted with polycarbonate membrane filters with 5µm diameter perforations. The flow rates were set to 0.5m3/min, and filters were changed once a week. After collection, filters were washed to remove salt and concentrate particles [see 5] in preparation for analysis by SEM. Results and Discussion: A selection of filters have been prepared and surveyed. Due to their ease of identification our initial investigations have focused on particles resembling cosmic spherules. The spheres can be divided into three main groups: 1. Silicate spherules rich in Al, Ca, K and Na (to varying degrees), 2. Silicate spherules rich in Mg and Fe and 3. Fe-rich spherules. Group 1 spherules are often vesiculated and can occur as aggregates. They are similar in appearance and composition to volcanic microspheres [e.g. 6] and are thus likely terrestrial in

A Novel Polygonal Finite Element Method: Virtual Node Method

Science.gov (United States)

Tang, X. H.; Zheng, C.; Zhang, J. H.

2010-05-01

Polygonal finite element method (PFEM), which can construct shape functions on polygonal elements, provides greater flexibility in mesh generation. However, the non-polynomial form of traditional PFEM, such as Wachspress method and Mean Value method, leads to inexact numerical integration. Since the integration technique for non-polynomial functions is immature. To overcome this shortcoming, a great number of integration points have to be used to obtain sufficiently exact results, which increases computational cost. In this paper, a novel polygonal finite element method is proposed and called as virtual node method (VNM). The features of present method can be list as: (1) It is a PFEM with polynomial form. Thereby, Hammer integral and Gauss integral can be naturally used to obtain exact numerical integration; (2) Shape functions of VNM satisfy all the requirements of finite element method. To test the performance of VNM, intensive numerical tests are carried out. It found that, in standard patch test, VNM can achieve significantly better results than Wachspress method and Mean Value method. Moreover, it is observed that VNM can achieve better results than triangular 3-node elements in the accuracy test.

Methods and results of the investigation of the thermomechanical behaviour of rock salt with regard to the final disposal of high-level radioactive wastes

International Nuclear Information System (INIS)

Wieczorek, K.; Klarr, K.

1993-01-01

This report summarizes the knowledge about thermal and mechanical behaviour of rock salt that has been accumulated by various R and D institutions in Germany from laboratory and in situ investigations. An important objective is to give a comprehensive overview of the investigation methods and instruments available and to discuss these methods and instruments with regard to their applicability and reliability for the investigation of the thermomechanical effects of high level radioactive waste emplacement in rock salt formations. The report is focused on the activities of the GSF-Institut fur Tieflagerung in the Asse mine regarding the disposal of high and intermediate level radioactive waste during the last decades. The design and the results of the most important in situ experiments are presented and discussed in detail. The results are compared to model calculations in order to evaluate the reliability of both the measurements and the calculation results. The relevance of the results for the situation in Spain is discussed in a separate chapter. As the investigations in Germany have been performed in domal salt, while the Spanish concept is based on waste disposal in bedded salt, significant differences in the thermomechanical behaviour cannot be excluded. The investigation methods, however, will be applicable. (Author)

Paleomagnetic intensity of Aso pyroclastic flows: Additional results with LTD-DHT Shaw method, Thellier method with pTRM-tail check

Science.gov (United States)

Maruuchi, T.; Shibuya, H.

2009-12-01

, and 42 specimens were submitted to Thellier experiments. Twelve specimens from 4 sites passed the same criteria as Aso-2, and yield a mean paleointensity of 43.1±1.4uT. It again agrees with the value (45.6±1.7uT) of Takai et al. (2002). LTD-DHT Shaw method experiment is also applied for 12 specimens from 3 sites, and 4 passed the criteria giving 38.2±1.7. Although it is a little smaller than Thellier results, it is way larger than the Sint-800 at the time of Aso-4. Aso-1 result in this study is more consistent with the Sint-800 at that time than Takai et al. (2002). But for Aso-2 and Aso-4, their new reliable paleointensity results suggest that the discrepancy from the Sint-800 is not attributed to the experimental problems.

Dimensionality Reduction Methods: Comparative Analysis of methods PCA, PPCA and KPCA

Directory of Open Access Journals (Sweden)

Jorge Arroyo-Hernández

2016-01-01

Full Text Available The dimensionality reduction methods are algorithms mapping the set of data in subspaces derived from the original space, of fewer dimensions, that allow a description of the data at a lower cost. Due to their importance, they are widely used in processes associated with learning machine. This article presents a comparative analysis of PCA, PPCA and KPCA dimensionality reduction methods. A reconstruction experiment of worm-shape data was performed through structures of landmarks located in the body contour, with methods having different number of main components. The results showed that all methods can be seen as alternative processes. Nevertheless, thanks to the potential for analysis in the features space and the method for calculation of its preimage presented, KPCA offers a better method for recognition process and pattern extraction

Effect of Chemistry Triangle Oriented Learning Media on Cooperative, Individual and Conventional Method on Chemistry Learning Result

Science.gov (United States)

Latisma D, L.; Kurniawan, W.; Seprima, S.; Nirbayani, E. S.; Ellizar, E.; Hardeli, H.

2018-04-01

The purpose of this study was to see which method are well used with the Chemistry Triangle-oriented learning media. This quasi experimental research involves first grade of senior high school students in six schools namely each two SMA N in Solok city, in Pasaman and two SMKN in Pariaman. The sampling technique was done by Cluster Random Sampling. Data were collected by test and analyzed by one-way anova and Kruskall Wallish test. The results showed that the high school students in Solok learning taught by cooperative method is better than the results of student learning taught by conventional and Individual methods, both for students who have high initial ability and low-ability. Research in SMK showed that the overall student learning outcomes taught by conventional method is better than the student learning outcomes taught by cooperative and individual methods. Student learning outcomes that have high initial ability taught by individual method is better than student learning outcomes that are taught by cooperative method and for students who have low initial ability, there is no difference in student learning outcomes taught by cooperative, individual and conventional methods. Learning in high school in Pasaman showed no significant difference in learning outcomes of the three methods undertaken.

Comparison of two dietary assessment methods by food consumption: results of the German National Nutrition Survey II.

Science.gov (United States)

Eisinger-Watzl, Marianne; Straßburg, Andrea; Ramünke, Josa; Krems, Carolin; Heuer, Thorsten; Hoffmann, Ingrid

2015-04-01

To further characterise the performance of the diet history method and the 24-h recalls method, both in an updated version, a comparison was conducted. The National Nutrition Survey II, representative for Germany, assessed food consumption with both methods. The comparison was conducted in a sample of 9,968 participants aged 14-80. Besides calculating mean differences, statistical agreement measurements encompass Spearman and intraclass correlation coefficients, ranking participants in quartiles and the Bland-Altman method. Mean consumption of 12 out of 18 food groups was higher assessed with the diet history method. Three of these 12 food groups had a medium to large effect size (e.g., raw vegetables) and seven showed at least a small strength while there was basically no difference for coffee/tea or ice cream. Intraclass correlations were strong only for beverages (>0.50) and revealed the least correlation for vegetables (diet history method to remember consumption of the past 4 weeks may be a source of inaccurateness, especially for inhomogeneous food groups. Additionally, social desirability gains significance. There is no assessment method without errors and attention to specific food groups is a critical issue with every method. Altogether, the 24-h recalls method applied in the presented study, offers advantages approximating food consumption as compared to the diet history method.

PRESENTATION POTENTIAL USING IN PEDAGOGICAL INTERACTION PROCESS

Directory of Open Access Journals (Sweden)

Olga V. Ershova

2016-01-01

Full Text Available The given article is aimed at considering multimedia presentation potential and its influence on strengthening classroom teacher-student interaction. In the article the importance of using this kind of activity in the study process is pointed in connection with educational state policy on the one hand. On the other hand, gained students’ skills as a final result of work with presentations met employers’ demand for both parent and world labour-markets and bring competitive benefit to the candidates. Scientific novelty and results. Multimedia presentation is considered as a specific complex of classroom activities. The students are oriented on the self analysis and presentation assessment. It is shown that well-organized process of peer students’ assessment allows to simultaneously helping in solving the didactic and methodical problems. To this purpose the system of assessment criteria should be developed. It has to be clear for students for making assessment feasible and time-saving. The example of a possible variant of criteria system is described; quality of the presentations prepared by students can be defined based on such system criteria. The author also analyzed software products of the three main platforms (Windows, Linux, MacOs which have different tools and allow to follow users’ needs for creating presentations. In the article there is a comparative table of the two most popular software development: the program Microsoft PowerPoint and the web-service Prezi for realizing the relevance of their use in the study process. Practical significance of the present article concludes in author’s suggestions of some recommendations for presentation potential use as a tool of improving pedagogical interaction process with contemporary students. 

Review on the present status of the German Risk Study: overall results

International Nuclear Information System (INIS)

Heuser, F.W.

1982-01-01

An overview on the most important results of the German Risk Study (Phase A) is given. Besides plant design analysis, the description mainly refers to core melt accidents, radioactive release and accidental consequences depending on various types of containment failure. Thereby some differences or results compared to WASH 1400 are discussed

Participatory Design Methods for C2 Systems (Proceedings/Presentation)

National Research Council Canada - National Science Library

Miller, Janet E

2006-01-01

... the capability and implementing for acceptance. The cognitive systems engineering and the software systems engineering communities struggle with the difficulties of understanding a domain and its challenges and then handing research results...

Present state and development of positron tomographs

International Nuclear Information System (INIS)

Allemand, R.; Gariod, R.; Laval, M.; Tournier, F.

1979-01-01

This document presents the main characteristics of positron tomographs and analyses the relative importance of the parameters to be taken into consideration in the design of a tomograph: on the one hand, the physical parameters linked to the measurement of the annihilation photons by time coincidence and, on the other, the geometrical and technological parameters of prime importance in minimizing the many spurious effects. The last part endeavours to show this sort of instrumentation has evolved. Using the results obtained in our laboratory by mathematical simulation, the expected advantages are presented on the picture quality of the time of flight measurement of annihilation photons. Where the physical aspects of this method are concerned, the advantage of using cesium fluoride as scintillator is demonstrated [fr

Acid-base titrations by stepwise addition of equal volumes of titrant with special reference to automatic titrations-III Presentation of a fully automatic titration apparatus and of results supporting the theories given in the preceding parts.

Science.gov (United States)

Pehrsson, L; Ingman, F

1977-02-01

This paper forms Part III of a series in which the first two parts describe methods for evaluating titrations performed by stepwise addition of equal volumes of titrant. The great advantage of these methods is that they do not require an accurate calibration of the electrode system. This property makes the methods very suitable for routine work. e.g., in automatic analysis. An apparatus for performing such titrations automatically is presented. Further, results of titrations of monoprotic acids, a diprotic acid, an ampholyte, a mixture of an acid with its conjugate base, and mixtures of two acids with a small difference between the stability constants are given. Most of these titrations cannot be evaluated by the Gran or Hofstee methods but yield results having errors of the order of 0.1% if the methods proposed in Parts I and II of this series are employed. The advantages of the method of stepwise addition of equal volumes of titrant combined with the proposed evaluation methods, in comparison with common methods such as titration to a preset pH, are that all the data are used in the evaluation, permitting a statistical treatment and giving better possibilities for tracing systematic errors.

THE YOUNG SOLAR ANALOGS PROJECT. I. SPECTROSCOPIC AND PHOTOMETRIC METHODS AND MULTI-YEAR TIMESCALE SPECTROSCOPIC RESULTS

Energy Technology Data Exchange (ETDEWEB)

Gray, R. O.; Briley, M. M.; Lambert, R. A.; Fuller, V. A.; Newsome, I. M.; Seeds, M. F. [Department of Physics and Astronomy, Appalachian State University, Boone, NC 26808 (United States); Saken, J. M.; Kahvaz, Y. [Department of Physics and Physical Science, Marshall University, Huntington, WV 25755 (United States); Corbally, C. J. [Vatican Observatory Research Group, Steward Observatory, Tucson, AZ 85721-0065 (United States)

2015-12-15

This is the first in a series of papers presenting methods and results from the Young Solar Analogs Project, which began in 2007. This project monitors both spectroscopically and photometrically a set of 31 young (300–1500 Myr) solar-type stars with the goal of gaining insight into the space environment of the Earth during the period when life first appeared. From our spectroscopic observations we derive the Mount Wilson S chromospheric activity index (S{sub MW}), and describe the method we use to transform our instrumental indices to S{sub MW} without the need for a color term. We introduce three photospheric indices based on strong absorption features in the blue-violet spectrum—the G-band, the Ca i resonance line, and the Hydrogen-γ line—with the expectation that these indices might prove to be useful in detecting variations in the surface temperatures of active solar-type stars. We also describe our photometric program, and in particular our “Superstar technique” for differential photometry which, instead of relying on a handful of comparison stars, uses the photon flux in the entire star field in the CCD image to derive the program star magnitude. This enables photometric errors on the order of 0.005–0.007 magnitude. We present time series plots of our spectroscopic data for all four indices, and carry out extensive statistical tests on those time series demonstrating the reality of variations on timescales of years in all four indices. We also statistically test for and discover correlations and anti-correlations between the four indices. We discuss the physical basis of those correlations. As it turns out, the “photospheric” indices appear to be most strongly affected by emission in the Paschen continuum. We thus anticipate that these indices may prove to be useful proxies for monitoring emission in the ultraviolet Balmer continuum. Future papers in this series will discuss variability of the program stars on medium (days–months) and short

Haemorrhagic Presentation of a Craniopharyngioma in a Pregnant Woman

Directory of Open Access Journals (Sweden)

Cesare Zoia

2014-01-01

Full Text Available Objective. Craniopharyngioma is a rare tumour, and, consequently, acute clinical presentation and diagnosis, during pregnancy, of this pathology are quite difficult to find. Only few cases are reported in the literature, and no one describes these two conditions in association. Methods. We report a particular case of craniopharyngioma presenting both of the above conditions. Results. The patient was successfully operated with endoscopic technique. Conclusions. Rare and difficult cases, created by the superposition of different clinical conditions, need multidisciplinary management, with collaboration, integration, and cooperation between different medical specialists.

Portal vein thrombosis; risk factors, clinical presentation and treatment

DEFF Research Database (Denmark)

Sogaard, Kirstine K; Astrup, Lone B; Vilstrup, Hendrik

2007-01-01

and treatment of portal vein thrombosis in a single-centre. METHODS: Sixty-seven patients were identified in the electronic records from 1992 to 2005. All data were obtained from the patient records. RESULTS: One or more risk factors (e.g. prothrombotic disorder or abdominal inflammation) were present in 87......BACKGROUND: Portal vein thrombosis (PVT) is increasingly frequently being diagnosed, but systematic descriptions of the natural history and clinical handling of the condition are sparse. The aim of this retrospective study was to describe risk factors, clinical presentation, complications...

The reaction π-p → π-π-π+p: Development of the analysis methods and selected results

Science.gov (United States)

Ryabchikov, D.

2016-01-01

We present the description of the analysis methods and results of applying them to the exclusive diffractive reaction π-p → π-π-π+p of 50 . 106 events measured with COMPASS detector. The large statistics of π-π-π+ events enables the two-dimensional partial-wave analysis independently in 100 bins of m(3π) with 0.5 < m(3π) < 2.5 GeV/c2 and in 11 intervals of squared momentum transfer with 0.1 < t' < 1 GeV2/c2. The partial-wave analysis sub-density matrix is the subject to further mass-dependent fits describing the data in terms of resonances in 3π system and coherent background contributions. The novel approach of extracting JPC = 0++(π+π-)S isobar amplitudes as model-free functions, different for several JPC 3π states, is used. It demonstrates the presence of processes π(1800) → f0(980)π and π(1800) → f0(1500)π as well as π2(1880) → f0(980)π and new narrow signal a1(1420) → f0(980)π, without any established shapes used for (π+π-)S isobars. The presented analysis is subject to further development and refinements which currently take place.

21st Century Extravehicular Activities: Synergizing Past and Present Training Methods for Future Spacewalking Success

Science.gov (United States)

Moore, Sandra K.; Gast, Matthew A.

2009-01-01

Neil Armstrong's understated words, "That's one small step for man, one giant leap for mankind." were spoken from Tranquility Base forty years ago. Even today, those words resonate in the ears of millions, including many who had yet to be born when man first landed on the surface of the moon. By their very nature, and in the the spirit of exploration, extravehicular activities (EVAs) have generated much excitement throughout the history of manned spaceflight. From Ed White's first space walk in June of 1965, to the first steps on the moon in 1969, to the expected completion of the International Space Station (ISS), the ability to exist, live and work in the vacuum of space has stood as a beacon of what is possible. It was NASA's first spacewalk that taught engineers on the ground the valuable lesson that successful spacewalking requires a unique set of learned skills. That lesson sparked extensive efforts to develop and define the training requirements necessary to ensure success. As focus shifted from orbital activities to lunar surface activities, the required skill-set and subsequently the training methods, changed. The requirements duly changed again when NASA left the moon for the last time in 1972 and have continued to evolve through the Skylab, Space Shuttle; and ISS eras. Yet because the visits to the moon were so long ago, NASA's expertise in the realm of extra-terrestrial EVAs has diminished. As manned spaceflight again shifts its focus beyond low earth orbit, EVA success will depend on the ability to synergize the knowledge gained over 40+ years of spacewalking to create a training method that allows a single crewmember to perform equally well, whether performing an EVA on the surface of the Moon, while in the vacuum of space, or heading for a rendezvous with Mars. This paper reviews NASA's past and present EVA training methods and extrapolates techniques from both to construct the basis for future EVA astronaut training.

21st Century extravehicular activities: Synergizing past and present training methods for future spacewalking success

Science.gov (United States)

Moore, Sandra K.; Gast, Matthew A.

2010-10-01

Neil Armstrong's understated words, "That's one small step for man, one giant leap for mankind" were spoken from Tranquility Base forty years ago. Even today, those words resonate in the ears of millions, including many who had yet to be born when man first landed on the surface of the moon. By their very nature, and in the true spirit of exploration, extravehicular activities (EVAs) have generated much excitement throughout the history of manned spaceflight. From Ed White's first spacewalk in the June of 1965, to the first steps on the moon in 1969, to the expected completion of the International Space Station (ISS), the ability to exist, live and work in the vacuum of space has stood as a beacon of what is possible. It was NASA's first spacewalk that taught engineers on the ground the valuable lesson that successful spacewalking requires a unique set of learned skills. That lesson sparked extensive efforts to develop and define the training requirements necessary to ensure success. As focus shifted from orbital activities to lunar surface activities, the required skill set and subsequently the training methods changed. The requirements duly changed again when NASA left the moon for the last time in 1972 and have continued to evolve through the SkyLab, Space Shuttle, and ISS eras. Yet because the visits to the moon were so long ago, NASA's expertise in the realm of extra-terrestrial EVAs has diminished. As manned spaceflight again shifts its focus beyond low earth orbit, EVA's success will depend on the ability to synergize the knowledge gained over 40+ years of spacewalking to create a training method that allows a single crewmember to perform equally well, whether performing an EVA on the surface of the Moon, while in the vacuum of space, or heading for a rendezvous with Mars. This paper reviews NASA's past and present EVA training methods and extrapolates techniques from both to construct the basis for future EVA astronaut training.

Enhancing activated-peroxide formulations for porous materials: Test methods and results

Energy Technology Data Exchange (ETDEWEB)

Krauter, Paula [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Tucker, Mark D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Tezak, Matthew S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Boucher, Raymond [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2012-12-01

During an urban wide-area incident involving the release of a biological warfare agent, the recovery/restoration effort will require extensive resources and will tax the current capabilities of the government and private contractors. In fact, resources may be so limited that decontamination by facility owners/occupants may become necessary and a simple decontamination process and material should be available for this use. One potential process for use by facility owners/occupants would be a liquid sporicidal decontaminant, such as pHamended bleach or activated-peroxide, and simple application devices. While pH-amended bleach is currently the recommended low-tech decontamination solution, a less corrosive and toxic decontaminant is desirable. The objective of this project is to provide an operational assessment of an alternative to chlorine bleach for low-tech decontamination applications activated hydrogen peroxide. This report provides the methods and results for activatedperoxide evaluation experiments. The results suggest that the efficacy of an activated-peroxide decontaminant is similar to pH-amended bleach on many common materials.

Biofilm biodiversity presented by fluorescent in situ hybridisation

Directory of Open Access Journals (Sweden)

Wolf Mirela

2017-01-01

Full Text Available Numerous microorganisms may be present in the water distribution system. This is associated with the imperfection of purification processes, or secondary water pollution. Not only it results in the deterioration of water quality parameters, but it also increases threat of epidemiological problems. The water that is biologically unstable creates ideal conditions for colonization of the microorganisms to the inner surface of pipelines which may form biofilm. The key issue, enabling prevention and control of the impact of the development of biofilms, is to assess the biodiversity of microbiocenosis. In order to obtain comprehensive characteristics of microorganisms communities on a particular substrate, it is necessary to combine several techniques. Further analysis using molecular biology methods are usually after traditional methods of assessing the microbiological quality of water. Standard methods do not reflect the actual species composition, because they are targeted at the bacteria that can be isolated and cultured in the laboratory. Conventional methods are capable of detecting less than 10% of the organisms in the sample. In order to study the biodiversity of organisms inhabiting a biofilm (apart from the conventional methods analyses of the diversity of nucleic acids should be used. The first method could be the polymerase chain reaction (PCR and denaturing gradient gel electrophoresis (DGGE. Another way may be fluorescence in situ hybridization, which allows to detect determined DNA sequence using specially labeled oligonucleotide probes. Visualization of the material is performed using a fluorescence microscope. The main purpose of this article is to present rapid and precise identification groups of microorganisms in their natural habitat in biofilm using fluorescent in situ hybridization method (FISH . FISH method can be successfully used to visualize these microorganisms, which show difficulties in culturing, as well as to provide

Water-quality trends in the nation’s rivers and streams, 1972–2012—Data preparation, statistical methods, and trend results

Science.gov (United States)

Oelsner, Gretchen P.; Sprague, Lori A.; Murphy, Jennifer C.; Zuellig, Robert E.; Johnson, Henry M.; Ryberg, Karen R.; Falcone, James A.; Stets, Edward G.; Vecchia, Aldo V.; Riskin, Melissa L.; De Cicco, Laura A.; Mills, Taylor J.; Farmer, William H.

2017-04-04

Since passage of the Clean Water Act in 1972, Federal, State, and local governments have invested billions of dollars to reduce pollution entering rivers and streams. To understand the return on these investments and to effectively manage and protect the Nation’s water resources in the future, we need to know how and why water quality has been changing over time. As part of the National Water-Quality Assessment Project, of the U.S. Geological Survey’s National Water-Quality Program, data from the U.S. Geological Survey, along with multiple other Federal, State, Tribal, regional, and local agencies, have been used to support the most comprehensive assessment conducted to date of surface-water-quality trends in the United States. This report documents the methods used to determine trends in water quality and ecology because these methods are vital to ensuring the quality of the results. Specific objectives are to document (1) the data compilation and processing steps used to identify river and stream sites throughout the Nation suitable for water-quality, pesticide, and ecology trend analysis, (2) the statistical methods used to determine trends in target parameters, (3) considerations for water-quality, pesticide, and ecology data and streamflow data when modeling trends, (4) sensitivity analyses for selecting data and interpreting trend results with the Weighted Regressions on Time, Discharge, and Season method, and (5) the final trend results at each site. The scope of this study includes trends in water-quality concentrations and loads (nutrient, sediment, major ion, salinity, and carbon), pesticide concentrations and loads, and metrics for aquatic ecology (fish, invertebrates, and algae) for four time periods: (1) 1972–2012, (2) 1982–2012, (3) 1992–2012, and (4) 2002–12. In total, nearly 12,000 trends in concentration, load, and ecology metrics were evaluated in this study; there were 11,893 combinations of sites, parameters, and trend periods. The

Locating previously unknown patterns in data-mining results: a dual data- and knowledge-mining method

Directory of Open Access Journals (Sweden)

Knaus William A

2006-03-01

Full Text Available Abstract Background Data mining can be utilized to automate analysis of substantial amounts of data produced in many organizations. However, data mining produces large numbers of rules and patterns, many of which are not useful. Existing methods for pruning uninteresting patterns have only begun to automate the knowledge acquisition step (which is required for subjective measures of interestingness, hence leaving a serious bottleneck. In this paper we propose a method for automatically acquiring knowledge to shorten the pattern list by locating the novel and interesting ones. Methods The dual-mining method is based on automatically comparing the strength of patterns mined from a database with the strength of equivalent patterns mined from a relevant knowledgebase. When these two estimates of pattern strength do not match, a high "surprise score" is assigned to the pattern, identifying the pattern as potentially interesting. The surprise score captures the degree of novelty or interestingness of the mined pattern. In addition, we show how to compute p values for each surprise score, thus filtering out noise and attaching statistical significance. Results We have implemented the dual-mining method using scripts written in Perl and R. We applied the method to a large patient database and a biomedical literature citation knowledgebase. The system estimated association scores for 50,000 patterns, composed of disease entities and lab results, by querying the database and the knowledgebase. It then computed the surprise scores by comparing the pairs of association scores. Finally, the system estimated statistical significance of the scores. Conclusion The dual-mining method eliminates more than 90% of patterns with strong associations, thus identifying them as uninteresting. We found that the pruning of patterns using the surprise score matched the biomedical evidence in the 100 cases that were examined by hand. The method automates the acquisition of

Improving the accuracy of myocardial perfusion scintigraphy results by machine learning method

International Nuclear Information System (INIS)

Groselj, C.; Kukar, M.

2002-01-01

Full text: Machine learning (ML) as rapidly growing artificial intelligence subfield has already proven in last decade to be a useful tool in many fields of decision making, also in some fields of medicine. Its decision accuracy usually exceeds the human one. To assess applicability of ML in interpretation the results of stress myocardial perfusion scintigraphy for CAD diagnosis. The 327 patient's data of planar stress myocardial perfusion scintigraphy were reevaluated in usual way. Comparing them with the results of coronary angiography the sensitivity, specificity and accuracy for the investigation was computed. The data were digitized and the decision procedure repeated by ML program 'Naive Bayesian classifier'. As the ML is able to simultaneously manipulate of whatever number of data, all reachable disease connected data (regarding history, habitus, risk factors, stress results) were added. The sensitivity, specificity and accuracy for scintigraphy were expressed in this way. The results of both decision procedures were compared. With ML method 19 patients more out of 327 (5.8 %) were correctly diagnosed by stress myocardial perfusion scintigraphy. ML could be an important tool for decision making in myocardial perfusion scintigraphy. (author)

Comparison between two sampling methods by results obtained using petrographic techniques, specially developed for minerals of the Itataia uranium phosphate deposit, Ceara, Brazil

International Nuclear Information System (INIS)

Salas, H.T.; Murta, R.L.L.

1985-01-01

The results of comparison of two sampling methods applied to a gallery of the uranium-phosphate ore body of Itataia-Ceara State, Brazil, along 235 metres of mineralized zone, are presented. The results were obtained through petrographic techniques especially developed and applied to both samplings. In the first one it was studied hand samples from a systematically sampling made at intervals of 2 metres. After that, the estimated mineralogical composition studies were carried out. Some petrogenetic observations were for the first time verified. The second sampling was made at intervals of 20 metres and 570 tons of ore extracted and distributed in sections and a sample representing each section was studied after crushing at -65. Their mineralogy were quantified and the degree of liberation of apatite calculated. Based on the mineralogical data obtained it was possible to represent both samplings and to make the comparison of the main mineralogical groups (phosphates, carbonates and silicates). In spite of utilizing different methods and methodology and the kind of mineralization, stockwork, being quite irregular, the results were satisfactory. (Author) [pt

A LIBS method for simultaneous monitoring of the impurities and the hydrogenic composition present in the wall of the TJ-II stellarator

Energy Technology Data Exchange (ETDEWEB)

López-Miranda, B., E-mail: belen.lopez@ciemat.es; Zurro, B.; Baciero, A. [Laboratorio Nacional de Fusión, CIEMAT, Av. Complutense, 40, 28040 Madrid (Spain); Martínez, M. [Universidad Carlos III de Madrid, Av de la Universidad, 30, 28911 Leganés, Madrid (Spain)

2016-11-15

The study of plasma-wall interactions and impurity transport in the plasma fusion devices is critical for the development of future fusion reactors. An experiment to perform laser induced breakdown spectroscopy, using minor modifications of our existing laser blow-off impurity injection system, has been set up thus making both experiments compatible. The radiation produced by the laser pulse focused at the TJ-II wall evaporates a surface layer of deposited impurities and the subsequent radiation produced by the laser-produced plasma is collected by two separate lens and fiber combinations into two spectrometers. The first spectrometer, with low spectral resolution, records a spectrum from 200 to 900 nm to give a survey of impurities present in the wall. The second one, with high resolution, is tuned to the wavelengths of the Hα and Dα lines in order to resolve them and quantify the hydrogen isotopic ratio present on the surface of the wall. The alignment, calibration, and spectral analysis method will be described in detail. First experimental results obtained with this setup will be shown and its relevance for the TJ-II experimental program discussed.

Nondestructive methods for the structural evaluation of wood floor systems in historic buildings : preliminary results : [abstract

Science.gov (United States)

Zhiyong Cai; Michael O. Hunt; Robert J. Ross; Lawrence A. Soltis

1999-01-01

To date, there is no standard method for evaluating the structural integrity of wood floor systems using nondestructive techniques. Current methods of examination and assessment are often subjective and therefore tend to yield imprecise or variable results. For this reason, estimates of allowable wood floor loads are often conservative. The assignment of conservatively...

Diagnostic methods in finding out the causes of infertility, results of HSG examination and laparoscopy in infertile women examined at the Gynecological Ward of the City Hospital

International Nuclear Information System (INIS)

Kwasniewski, S.; Kukulski, P.; Szymanski, J.; Kwasniewska, A.

1993-01-01

The paper presents diagnostic methods and the results of hysterosalpingography (HSG) and laparoscopy examination, with special attention being drawn to the usefulness of these methods in finding out the causes of infertility. 51 patients with primary and second infertility were examined. HSG and laparoscopy make it possible to diagnose correctly the cause of infertility. They also enable adequate and early classification of patients for further diagnosis and treatment at highly specialized centers dealing with the problems of infertility. (author)

Discipline methods

OpenAIRE

Maria Kikila; Ioannis Koutelekos

2012-01-01

Child discipline is one of the most important elements of successful parenting. As discipline is defined the process that help children to learn appropriate behaviors and make good choices. Aim: The aim of the present study was to review the literature about the discipline methods. The method οf this study included bibliography research from both the review and the research literature, mainly in the pubmed data base which referred to the discipline methods. Results: In the literature it is ci...

Mixed method approach for determining factors associated with late presentation to HIV/AIDS care in southern India

Directory of Open Access Journals (Sweden)

U N Yadav

2016-01-01

Full Text Available Background: Early diagnosis and treatment of human Immunodeficiency virus (HIV is not only beneficial for the people living with HIV/acquired immunodeficiency syndrome (AIDS (PLHA but for the public and society as well. The study was aimed to identify the factors associated with late presentation to HIV/AIDS care. Materials and Methods: A facility-based unmatched case-control (1:1 study along with in-depth qualitative assessment was conducted at an ART Plus center at a district hospital, Udupi, southern India. A sample of 320 HIV patients (160 cases and 160 controls was selected randomly between February and July 2014. Information regarding the patients were collected using an interviewer-administered semi-structured questionnaire. The qualitative component was assessed by in-depth interviews of 4 health professionals and 12 HIV-positive patients who were late for HIV care. The quantitative data were analyzed using Statistical Package for the Social Sciences (SPSS version 15.0. The technique of thematic analysis was adopted for the analysis of qualitative data. Results: HIV-positive individuals who lived with families [odds ratio (OR = 5.11], the patients having non-AIDS comorbidities [OR= 2.19, 95% confidence interval (CI: 1.09-4.40], the patients who perceived fear of losing family [OR = 5.00, 95% CI: 2.17-11.49], the patients who perceived fear that their status will be ruined in the community [OR= 2.00, 95% CI: 1.01-3.97], the patients who perceived fear of side effects of ART medications [OR = 4.3, 95% CI: 2.65-11.33], the patients who perceived fear of losing confidentiality [OR = 4.94, 95% CI: 2.54-9.59], the patients those who lack information available on government services [OR = 4.12, 95% CI: 2.127-8.005], and the patients who consumed alcohol [OR= 3.52, 95% CI: 1.83-6.77] were found to be independently associated with the late presentation to HIV/AIDS care after adjusting for all known confounders in a multivariable analysis. The

Results of the determination of He in cenozoic aquifers using the GC method.

Science.gov (United States)

Kotowski, Tomasz; Najman, Joanna

2015-04-01

Applications of the Helium (He) method known so far consisted mainly of 4He measurements using a special mass spectrometer. 4He measurements for groundwater dating purposes can be replaced by total He (3He+4He) concentration measurements because the content of 3He can be ignored. The concentrations of 3He are very low and 3He/4 He ratios do not exceed 1.0·10(-5) in most cases. In this study, the total He concentrations in groundwater were determined using the gas chromatographic (GC) method as an alternative to methods based on spectrometry measurement. He concentrations in groundwater were used for the determination of residence time and groundwater circulation. Additionally, the radiocarbon method was used to determine the value of the external He flux (JHe) in the study area. Obtained low He concentrations and their small variation within the ca. 65 km long section along which groundwater flows indicate that it is likely there is relatively short residence time and a strong hydraulic connection between the aquifers. The estimated residence time (ca. 3000 years) is heavily dependent on the great uncertainty of the He concentration resulting from the low concentrations of He, the external 4He flux value adopted for calculation purposes and the 14C ages used to estimate the external 4He flux. © 2015, National Ground Water Association.

Governmental entities accounting: domestic standards and foreign experience of preparation and presentation

Directory of Open Access Journals (Sweden)

Ambarchian V.S.

2015-12-01

Full Text Available The purpose of research refers to comparison of Ukrainian and the USA standards of preparation and presentation of governmental entities financial reports with the aim of implementation of foreign experience regarding financial data disclosure of a governmental entity activity in domestic reporting system of budgetary resources disposers. In order to achieve the aim the author applied the following general methods of cognition: induction, deduction, analogy, comparison, and historical one. Special economic methods include grouping, tabular, graphical, information and logical analysis. The research resulted in detailed analysis of the standards of the USA governmental entities financial reports presentation and comparison of their statements with domestic governmental accounting standards. As a result of performed research, the key differences in the Ukrainian and the USA rules of presentation of governmental entities financial reports are considered. The author determined the dependence of structure and a public level of the financial reports on the character of the state political and economic systems.

Actual interaction effects between policy measures for energy efficiency-A qualitative matrix method and quantitative simulation results for households

International Nuclear Information System (INIS)

Boonekamp, Piet G.M.

2006-01-01

Starting from the conditions for a successful implementation of saving options, a general framework was developed to investigate possible interaction effects in sets of energy policy measures. Interaction regards the influence of one measure on the energy saving effect of another measure. The method delivers a matrix for all combinations of measures, with each cell containing qualitative information on the strength and type of interaction: overlapping, reinforcing, or independent of each other. Results are presented for the set of policy measures on household energy efficiency in the Netherlands for 1990-2003. The second part regards a quantitative analysis of the interaction effects between three major measures: a regulatory energy tax, investment subsidies and regulation of gas use for space heating. Using a detailed bottom-up model, household energy use in the period 1990-2000 was simulated with and without these measures. The results indicate that combinations of two or three policy measures yield 13-30% less effect than the sum of the effects of the separate measures

A convenient method for estimating the contaminated zone of a subsurface aquifer resulting from radioactive waste disposal into ground

International Nuclear Information System (INIS)

Fukui, Masami; Katsurayama, Kousuke; Uchida, Shigeo.

1981-01-01

Studies were conducted to estimate the contamination spread resulting from the radioactive waste disposal into a subsurface aquifer. A general equation, expressing the contaminated zone as a function of radioactive decay, the physical and chemical parameters of soil is presented. A distribution coefficient was also formulated which can be used to judge the suitability of a site for waste disposal. Moreover, a method for predicting contaminant concentration in groundwater at a site boundary is suggested for a heterogeneous media where the subsurface aquifer has different values of porosity, density, flow velocity, distribution coefficient and so on. A general equation was also developed to predict the distribution of radionuclides resulting from the disposal of a solid waste material. The distributions of contamination was evaluated for 90 Sr and 239 Pu which obey a linear adsorption model and a first order kinetics respectively. These equations appear to have practical utility for easily estimating groundwater contamination. (author)

JNC results of BN-600 benchmark calculation (phase 3)

International Nuclear Information System (INIS)

Ishikawa, M.

2002-01-01

The present work is the result of phase 3 BN-600 core benchmark problem, meaning burnup and heterogeneity. Analytical method applied consisted of: JENDL-3.2 nuclear data library, group constants (70 group, ABBN type self shielding transport factors), heterogeneous cell model for fuel and control rod, basic diffusion calculation (CITATION code), transport theory and mesh size correction (NSHEX code based on SN transport nodal method developed by JNC). Burnup and heterogeneity calculation results are presented obtained by applying both diffusion and transport approach for beginning and end of cycle

Bibliography of papers, reports, and presentations related to point-sample dimensional measurement methods for machined part evaluation

Energy Technology Data Exchange (ETDEWEB)

Baldwin, J.M. [Sandia National Labs., Livermore, CA (United States). Integrated Manufacturing Systems

1996-04-01

The Dimensional Inspection Techniques Specification (DITS) Project is an ongoing effort to produce tools and guidelines for optimum sampling and data analysis of machined parts, when measured using point-sample methods of dimensional metrology. This report is a compilation of results of a literature survey, conducted in support of the DITS. Over 160 citations are included, with author abstracts where available.

Emission-Line Galaxies from the PEARS Hubble Ultra Deep Field: A 2-D Detection Method and First Results

Science.gov (United States)

Gardner, J. P.; Straughn, Amber N.; Meurer, Gerhardt R.; Pirzkal, Norbert; Cohen, Seth H.; Malhotra, Sangeeta; Rhoads, james; Windhorst, Rogier A.; Gardner, Jonathan P.; Hathi, Nimish P.;

Pile Load Capacity – Calculation Methods

Directory of Open Access Journals (Sweden)

Wrana Bogumił

2015-12-01

Full Text Available The article is a review of the current problems of the foundation pile capacity calculations. The article considers the main principles of pile capacity calculations presented in Eurocode 7 and other methods with adequate explanations. Two main methods are presented: α – method used to calculate the short-term load capacity of piles in cohesive soils and β – method used to calculate the long-term load capacity of piles in both cohesive and cohesionless soils. Moreover, methods based on cone CPTu result are presented as well as the pile capacity problem based on static tests.

Cognitive Constraints on Multimedia Learning: When Presenting More Material Results in Less Understanding.

Science.gov (United States)

Mayer, Richard E.; Heiser, Julie; Lonn, Steve

2001-01-01

Presents research on and discusses the redundancy effect, consistent with a dual-channel theory of multimedia learning in which adding on-screen text can overload the visual information-processing channel, causing learners to split their visual attention between two sources. In research, lower transfer performance also occurred when interesting…

Present status and future of simple measuring methods; Suishitsu kan`i sokutei gijutsu no genjo to hatten no hoko

Energy Technology Data Exchange (ETDEWEB)

Urano, K.; Ishii, S. [Yokohama National University, Yokohama (Japan)

1998-05-10

This paper discusses simple measuring methods for water quality. There are various purposes for measuring water quality. It is not necessary to measure the water quality in an official way by taking a lot of labor and cost. Simple measuring methods are often adopted. By applying simple methods, measuring points and frequency of main discharge processes can be increased, resulting in the detailed evaluation and monitoring. Easy safety check for earth filling waste and soil pollutants is realized. Daily inspection and atmospheric measurements at accidents and disasters are easily promoted. The simple methods require easy and rapid operation, sensibility, accuracy and reproducibility suitable for the purpose, small size apparatus, low cost for measurements, and safety against used harmful matters. Coloring reaction is utilized for most of the measuring principles of simple methods, which include tests using test papers, pack tests, colorimetric tests, and tests using photoelectric colorimeter. The bacteria detection includes titration methods using dropping bottles, tablets and syringes, and tests using test papers. A measuring kit for the enzyme immunity method is commercialized. Cooperation of experts, measuring operators at the site and citizens is also indispensable. 7 refs., 3 figs., 2 tabs.

Nuclear methods in constructing engineering - present state, tendencies, education and in-service training

International Nuclear Information System (INIS)

Baumbach, H.

1988-01-01

Evaluation and status of nuclear methods in the field of civil engineering are pointed out. Exemplary remarks are made out neutron small-angle scattering and on field gradient-impulse NMR method for studies of hydration of cement concrete. Moreover, the application of radioisotopes in gas concrete production, gamma radiography and gamma tomography are discussed in detail. (author)

New radiochemical methods for determination of 237Np a 241Pu using extraction chromatography (Presentation)

International Nuclear Information System (INIS)

Strisovska, J.

2013-01-01

Thesis was focused on the development of a new methodology for the separation of anthropogenic transuranium radionuclides 237 Np a 241 Pu from different kinds of matrices. The analytical methods used in this study were based on extraction chromatography and were optimized according to the sample type. The proposed radiochemical procedure is a combination of two algorithms, which represent the separation of radionuclides by using extraction chromatographic sorbents TEVA resin and TRU resin supplied by Eichrom Technologies LLC. 239 Np a 237 Np were selectively captured on sorbent TEVA resin in oxidation state 4+. TRU resin was used for purification of plutonium fraction from interfering americium radionuclide. 242 Pu and 239 Np radionuclides as tracers have been used to monitor the radiochemical yields of separation. Before every radiochemical separation tracer radionuclide 239 Np was obtained by separation from the parent radionuclide 2 43 Am, which is in radioactive equilibrium to 239 Np. The average yield of chemical separation was 69,3% for 239 Np at 277 keV energy line and 65,9% at 228 keV energy line. The NPL AH-B08069 (2008) samples which consist of the mixture of alpha-radionuclides were used for the modification and optimization of separation method used for separation of Np and Pu in model samples. This method provided high radiochemical yields of 239,240 Pu (95,0 ± 3,5)% and 237 Np (87,9 ± 3,0)%.. Reliability of the method was verified by applying our modified separation procedures on reference materials IAEA-375 and IAEA-414 supplied by International Atomic Energy Agency. A good agreement between the results is obtained by this procedure and the certified values were found. Samples of contaminated soils from the area of Nuclear power plant A-1 Jaslovske Bohunice which is stored temporarily before disposal were analyzed using developed separation procedure. Specific activity of investigated radionuclides was determined in these samples. (author)

The Method of Manufactured Universes for validating uncertainty quantification methods

KAUST Repository

Stripling, H.F.

2011-09-01

The Method of Manufactured Universes is presented as a validation framework for uncertainty quantification (UQ) methodologies and as a tool for exploring the effects of statistical and modeling assumptions embedded in these methods. The framework calls for a manufactured reality from which experimental data are created (possibly with experimental error), an imperfect model (with uncertain inputs) from which simulation results are created (possibly with numerical error), the application of a system for quantifying uncertainties in model predictions, and an assessment of how accurately those uncertainties are quantified. The application presented in this paper manufactures a particle-transport universe, models it using diffusion theory with uncertain material parameters, and applies both Gaussian process and Bayesian MARS algorithms to make quantitative predictions about new experiments within the manufactured reality. The results of this preliminary study indicate that, even in a simple problem, the improper application of a specific UQ method or unrealized effects of a modeling assumption may produce inaccurate predictions. We conclude that the validation framework presented in this paper is a powerful and flexible tool for the investigation and understanding of UQ methodologies. © 2011 Elsevier Ltd. All rights reserved.

Ilmenite exploration on the Senegal continental shelf. Methods and results

International Nuclear Information System (INIS)

Horn, R.; Le Lann, F.; Scolari, G.; Tixeront, M.

1975-01-01

From the results of a study based on geomorphology, geophysics and sedimentology, it has been possible to point out, South of Dakar, the existence of a fossil lagoon (peat dated 8400 years BP) partly isolated from the open sea by a littoral sand bar at -25m and strongly eroded. To the North of Dakar, the unconsolidated sediments, with a thickness over 40m, are thinning out seawards and from North of Dakar, the unconsolidated sediments, with a thickness over 40m, are thinning out seawards and from North to South. This pattern reflect the action of the longshore current which overstates the drainage effect to the Cayar canyon. The distribution of ilmenites in the sediments is studied in terms of a possible exploitation however, the grades are too low in the present economic conditions [fr

Some new results on correlation-preserving factor scores prediction methods

NARCIS (Netherlands)

Ten Berge, J.M.F.; Krijnen, W.P.; Wansbeek, T.J.; Shapiro, A.

1999-01-01

Anderson and Rubin and McDonald have proposed a correlation-preserving method of factor scores prediction which minimizes the trace of a residual covariance matrix for variables. Green has proposed a correlation-preserving method which minimizes the trace of a residual covariance matrix for factors.

Quantifying viruses and bacteria in wastewater—Results, interpretation methods, and quality control

Science.gov (United States)

Francy, Donna S.; Stelzer, Erin A.; Bushon, Rebecca N.; Brady, Amie M.G.; Mailot, Brian E.; Spencer, Susan K.; Borchardt, Mark A.; Elber, Ashley G.; Riddell, Kimberly R.; Gellner, Terry M.

2011-01-01

Membrane bioreactors (MBR), used for wastewater treatment in Ohio and elsewhere in the United States, have pore sizes small enough to theoretically reduce concentrations of protozoa and bacteria, but not viruses. Sampling for viruses in wastewater is seldom done and not required. Instead, the bacterial indicators Escherichia coli (E. coli) and fecal coliforms are the required microbial measures of effluents for wastewater-discharge permits. Information is needed on the effectiveness of MBRs in removing human enteric viruses from wastewaters, particularly as compared to conventional wastewater treatment before and after disinfection. A total of 73 regular and 28 quality-control (QC) samples were collected at three MBR and two conventional wastewater plants in Ohio during 23 regular and 3 QC sampling trips in 2008-10. Samples were collected at various stages in the treatment processes and analyzed for bacterial indicators E. coli, fecal coliforms, and enterococci by membrane filtration; somatic and F-specific coliphage by the single agar layer (SAL) method; adenovirus, enterovirus, norovirus GI and GII, rotavirus, and hepatitis A virus by molecular methods; and viruses by cell culture. While addressing the main objective of the study-comparing removal of viruses and bacterial indicators in MBR and conventional plants-it was realized that work was needed to identify data analysis and quantification methods for interpreting enteric virus and QC data. Therefore, methods for quantifying viruses, qualifying results, and applying QC data to interpretations are described in this report. During each regular sampling trip, samples were collected (1) before conventional or MBR treatment (post-preliminary), (2) after secondary or MBR treatment (post-secondary or post-MBR), (3) after tertiary treatment (one conventional plant only), and (4) after disinfection (post-disinfection). Glass-wool fiber filtration was used to concentrate enteric viruses from large volumes, and small

Classes evaluation: Methods and tools

Directory of Open Access Journals (Sweden)

Grabiński Tadeusz

2013-01-01

Full Text Available This study presents a method, tools, course and results of foreign language classes evaluation conducted in the summer semester 2012/2013 in the Andrzej Frycz - Modrzewski Krakow University. Because a new evaluation procedure has been implemented at the University, the former method - based on paper forms filled in by the students - was abandoned. On the surveyanyplace.com website, a free account has been registered and the form of the evaluation questionnaire has been inserted. This coverage presents results of a taxometric analysis aimed at checking the degree of mutual correspondence (correlation between certain criteria and instancing a graphic presentation of the evaluation results in a multidimensional perspective. In order to classify the grading criteria, the Ward's agglomerative method, along with Euclidean metric as a measure of criteria similarity, have been used. Calculations have been made with the use of Statistica package. Results of the questionnaire show that foreign language teaching at the Andrzej Frycz Modrzewski Krakow University is conducted professionally and on a high factual level.

Monte Carlo method for neutron transport problems

International Nuclear Information System (INIS)

Asaoka, Takumi

1977-01-01

Some methods for decreasing variances in Monte Carlo neutron transport calculations are presented together with the results of sample calculations. A general purpose neutron transport Monte Carlo code ''MORSE'' was used for the purpose. The first method discussed in this report is the method of statistical estimation. As an example of this method, the application of the coarse-mesh rebalance acceleration method to the criticality calculation of a cylindrical fast reactor is presented. Effective multiplication factor and its standard deviation are presented as a function of the number of histories and comparisons are made between the coarse-mesh rebalance method and the standard method. Five-group neutron fluxes at core center are also compared with the result of S4 calculation. The second method is the method of correlated sampling. This method was applied to the perturbation calculation of control rod worths in a fast critical assembly (FCA-V-3) Two methods of sampling (similar flight paths and identical flight paths) are tested and compared with experimental results. For every cases the experimental value lies within the standard deviation of the Monte Carlo calculations. The third method is the importance sampling. In this report a biased selection of particle flight directions discussed. This method was applied to the flux calculation in a spherical fast neutron system surrounded by a 10.16 cm iron reflector. Result-direction biasing, path-length stretching, and no biasing are compared with S8 calculation. (Aoki, K.)

Comments on Brodsky's statistical methods for evaluating epidemiological results, and reply by Brodsky, A

International Nuclear Information System (INIS)

Frome, E.L.; Khare, M.

1980-01-01

Brodsky's paper 'A Statistical Method for Testing Epidemiological Results, as applied to the Hanford Worker Population', (Health Phys., 36, 611-628, 1979) proposed two test statistics for use in comparing the survival experience of a group of employees and controls. This letter states that both of the test statistics were computed using incorrect formulas and concludes that the results obtained using these statistics may also be incorrect. In his reply Brodsky concurs with the comments on the proper formulation of estimates of pooled standard errors in constructing test statistics but believes that the erroneous formulation does not invalidate the major points, results and discussions of his paper. (author)

The relationship between team climate and interprofessional collaboration: preliminary results of a mixed methods study

OpenAIRE

Bailey, Christopher; Agreli, Heloise F.; Peduzzi, Marina

2016-01-01

Relational and organisational factors are key elements of interprofessional collaboration (IPC) and team climate. Few studies have explored the relationship between IPC and team climate. This article presents a study that 10 aimed to explore IPC in primary healthcare teams and understand how the assessment of team climate may provide insights into IPC. A mixed methods study design was adopted. In Stage 1 of the study, team climate was assessed using the Team Climate Inventory with 159 profess...

Semiautomatic volume of interest drawing for 18F-FDG image analysis - method and preliminary results

International Nuclear Information System (INIS)

Green, A.J.; Baig, S.; Begent, R.H.J.; Francis, R.J.

2008-01-01

Functional imaging of cancer adds important information to the conventional measurements in monitoring response. Serial 18 F-fluorodeoxyglucose (FDG) positron emission tomography (PET), which indicates changes in glucose metabolism in tumours, shows great promise for this. However, there is a need for a method to quantitate alterations in uptake of FDG, which accounts for changes in tumour volume and intensity of FDG uptake. Selection of regions or volumes [ROI or volumes of interest (VOI)] by hand drawing, or simple thresholding, suffers from operator-dependent drawbacks. We present a simple, robust VOI growing method for this application. The method requires a single seed point within the visualised tumour and another in relevant normal tissue. The drawn tumour VOI is insensitive to the operator inconsistency and is, thus, a suitable basis for comparative measurements. The method is validated using a software phantom. We demonstrate the use of the method in the assessment of tumour response in 31 patients receiving chemotherapy for various carcinomas. Valid assessment of tumour response could be made 2-4 weeks after starting chemotherapy, giving information for clinical decision making which would otherwise have taken 9-12 weeks. Survival was predicted from FDG-PET 2-4 weeks after starting chemotherapy (p = 0.04) and after 9-12 weeks FDG-PET gave a better prediction of survival (p = 0.002) than CT or MRI (p = 0.015). FDG-PET using this method of analysis has potential as a routine tool for optimising use of chemotherapy and improving its cost effectiveness. It also has potential for increasing the accuracy of response assessment in clinical trials of novel therapies. (orig.)

3D ultrasound computer tomography: Hardware setup, reconstruction methods and first clinical results

Science.gov (United States)

Gemmeke, Hartmut; Hopp, Torsten; Zapf, Michael; Kaiser, Clemens; Ruiter, Nicole V.

2017-11-01

A promising candidate for improved imaging of breast cancer is ultrasound computer tomography (USCT). Current experimental USCT systems are still focused in elevation dimension resulting in a large slice thickness, limited depth of field, loss of out-of-plane reflections, and a large number of movement steps to acquire a stack of images. 3D USCT emitting and receiving spherical wave fronts overcomes these limitations. We built an optimized 3D USCT, realizing for the first time the full benefits of a 3D system. The point spread function could be shown to be nearly isotropic in 3D, to have very low spatial variability and fit the predicted values. The contrast of the phantom images is very satisfactory in spite of imaging with a sparse aperture. The resolution and imaged details of the reflectivity reconstruction are comparable to a 3 T MRI volume. Important for the obtained resolution are the simultaneously obtained results of the transmission tomography. The KIT 3D USCT was then tested in a pilot study on ten patients. The primary goals of the pilot study were to test the USCT device, the data acquisition protocols, the image reconstruction methods and the image fusion techniques in a clinical environment. The study was conducted successfully; the data acquisition could be carried out for all patients with an average imaging time of six minutes per breast. The reconstructions provide promising images. Overlaid volumes of the modalities show qualitative and quantitative information at a glance. This paper gives a summary of the involved techniques, methods, and first results.

Present studies on the radiosterilized drugs

International Nuclear Information System (INIS)

Marciniec, B.; Dettlaff, K.

2007-01-01

Lecture presents present status of radiosterilization of drugs and medical materials as compared to other sterilization methods. Literature review is shown on degradation of different kinds of drugs sterilized upon action of the sterilising doses of radiation

The possible distortion of autoradiographic results

International Nuclear Information System (INIS)

Kozlov, A.A.; Tumanushvili, G.D.

1980-01-01

The effect of radioactive labelling (H 3 -thymidine) on the infusorian division is studied. The presented results show that introduction of labelled compounds results in accelerating infusorian cell division v. Thorough inestigation of labelled compound effect with low activity on the parameters of cell division and the search of methods to eliminate distortions able to appear in autoradiographic experiments is expedient [ru

Giant Leaking Colloid Cyst Presenting with Aseptic Meningitis

DEFF Research Database (Denmark)

Bakhtevari, Mehrdad Hosseinzadeh; Sharifi, Guive; Jabbari, Reza

2015-01-01

BACKGROUND: Colloid cysts are benign third ventricle lesions that need to be diagnosed correctly because of their association with sudden death. Chemical or aseptic meningitis is a rare presentation of a colloid cyst. METHODS: We present a case of a 69-year-old man with fever, alteration of mental...... status, and meningismus. Microbiological examination of the cerebrospinal fluid revealed aseptic meningitis. Brain imaging revealed a third ventricular colloid cyst with hydrocephalus. RESULTS: The tumor was resected via endoscopic intervention. There were no persistent operative complications related...... to the endoscopic procedure. CONCLUSIONS: Chemical or aseptic meningitis is an unusual clinical manifestation of a colloid cyst, complicating the differential diagnosis, especially in the elderly....

Fuzzy net present value for engineering analysis

Directory of Open Access Journals (Sweden)

Ali Nazeri

2012-10-01

Full Text Available Cash flow analysis is one of the most popular methods for investigating the outcome of an economical project. The costs and benefits of a construction project are often involved with uncertainty and it is not possible to find a precise value for a particular project. In this paper, we present a simple method to calculate the net present value of a cash flow when both costs and benefits are given as triangular numbers. The proposed model of this paper uses Delphi method to figure out the fair values of all costs and revenues and then using fizzy programming techniques, it calculates the fuzzy net present value. The implementation of the proposed model is demonstrated using a simple example.

Computational modeling of objects presented in images fundamentals, methods and applications

CERN Document Server

Iacoviello, Daniela; Jorge, Renato; Tavares, João

2014-01-01

This book contains extended versions of selected papers from the 3rd edition of the International Symposium CompIMAGE. These contributions include cover methods of signal and image processing and analysis to tackle problems found in medicine, material science, surveillance, biometric, robotics, defence, satellite data, traffic analysis and architecture, image segmentation, 2D and 3D reconstruction, data acquisition, interpolation and registration, data visualization, motion and deformation analysis, and 3D vision

Radiological environmental dose assessment methods and compliance dose results for 2015 operations at the Savannah River Site

Energy Technology Data Exchange (ETDEWEB)

Jannik, G. T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Dixon, K. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-09-01

This report presents the environmental dose assessment methods and the estimated potential doses to the offsite public from 2015 Savannah River Site (SRS) atmospheric and liquid radioactive releases. Also documented are potential doses from special-case exposure scenarios - such as the consumption of deer meat, fish, and goat milk.

Radiological environmental dose assessment methods and compliance dose results for 2015 operations at the Savannah River Site

International Nuclear Information System (INIS)

Jannik, G. T.; Dixon, K. L.

2016-01-01

This report presents the environmental dose assessment methods and the estimated potential doses to the offsite public from 2015 Savannah River Site (SRS) atmospheric and liquid radioactive releases. Also documented are potential doses from special-case exposure scenarios - such as the consumption of deer meat, fish, and goat milk.

Behavioural present value

OpenAIRE

Krzysztof Piasecki

2013-01-01