WorldWideScience

Sample records for methods previously investigated

  1. Investigating physiological methods to determine previous exposure of immature insects to ionizing radiation

    International Nuclear Information System (INIS)

    Mansour, M.Y.

    2001-01-01

    Effect of gamma radiation on phenoloxidase activity in codling moth, Cydia pomonella L., larvae was investigated. Phenoloxidase activity was determined spectrophotometrically by measuring the increase in optical density at 490 nm, or by observing the degree of melanization in larvae killed by freezing. Results showed that, in unirradiated larvae, phenoloxidase activity could be detected in 7 day old larvae and activity continued to increase throughout the larval stage. This increase was not observed when larvae were irradiated with a minimum dose of 50 Gy during the 1st week of their development. However, irradiating larvae in which enzyme activity was already high (24 week old) did not eliminate the activity but reduced further increase. Larval melanization studies were in general agreement with the results of the phenoloxidase assay. (author)

  2. Investigating physiological methods to determine previous exposure of immature insects to ionizing radiation and estimating the exposure dose

    International Nuclear Information System (INIS)

    Mansour, M.

    1998-10-01

    Effects of gamma radiation on pupation and adult emergence in mature (diapausing and non-diapausing) codling moth, Cydia pomonella L., larvae and on phenoloxidase activity in larvae killed by freezing were investigated. Results showed that, a dose of 50 Gy reduced adult emergence (and pupation) significantly and 200 Gy completely prevented it. Diapausing larvae were more susceptible to irradiation that non-diapausing larvae and female moths were more susceptible to irradiation injury than males. Phenoloxidase activity in codling moth larvae was determined spectrophotometrically by measuring the increase in optical density at 490 nm, or by observing the degree of melanization in larvae killed by freezing. Results showed that, in un-irradiated larvae, phenoloxidase activity can be detected in 7 day old larvae and activity continued to accumulate throughout the larval stage. This accumulation was not observed when larvae were irradiated with a minimum dose of 50 Gy during the 1st week of their development. However, irradiating larvae in which enzyme activity was already high (2-3 week old) did not remove activity but only reduced further accumulation. Larval melanization studies were in agreement with results of the phenoloxidase assay. (author)

  3. Investigation of previously derived Hyades, Coma, and M67 reddenings

    International Nuclear Information System (INIS)

    Taylor, B.J.

    1980-01-01

    New Hyades polarimetry and field star photometry have been obtained to check the Hyades reddening, which was found to be nonzero in a previous paper. The new Hyades polarimetry implies essentially zero reddening; this is also true of polarimetry published by Behr (which was incorrectly interpreted in the previous paper). Four photometric techniques which are presumed to be insensitive to blanketing are used to compare the Hyades to nearby field stars; these four techniques also yield essentially zero reddening. When all of these results are combined with others which the author has previously published and a simultaneous solution for the Hyades, Coma, and M67 reddenings is made, the results are E (B-V) =3 +- 2 (sigma) mmag, -1 +- 3 (sigma) mmag, and 46 +- 6 (sigma) mmag, respectively. No support for a nonzero Hyades reddening is offered by the new results. When the newly obtained reddenings for the Hyades, Coma, and M67 are compared with results from techniques given by Crawford and by users of the David Dunlap Observatory photometric system, no differences between the new and other reddenings are found which are larger than about 2 sigma. The author had previously found that the M67 main-sequence stars have about the same blanketing as that of Coma and less blanketing than the Hyades; this conclusion is essentially unchanged by the revised reddenings

  4. Methods of respiratory system investigation

    International Nuclear Information System (INIS)

    Rozenshtraukh, L.C.; Rybakova, N.I.; Vinner, M.G.

    1987-01-01

    Different methods of chest organs investigation are discussed in detail: roentgenoscopy, roentgenography, tomography and others. A detailed roentgenologic semiotics of every method is presented, as well as their comparative evaluation

  5. Fire Risk Scoping Study: Investigation of nuclear power plant fire risk, including previously unaddressed issues

    International Nuclear Information System (INIS)

    Lambright, J.A.; Nowlen, S.P.; Nicolette, V.F.; Bohn, M.P.

    1989-01-01

    An investigation of nuclear power plant fire risk issues raised as a result of the USNRC sponsored Fire Protection Research Program at Sandia National Laboratories has been performed. The specific objectives of this study were (1) to review and requantify fire risk scenarios from four fire probabilistic risk assessments (PRAs) in light of updated data bases made available as a result of USNRC sponsored Fire Protection Research Program and updated computer fire modeling capabilities, (2) to identify potentially significant fire risk issues that have not been previously addressed in a fire risk context and to quantify the potential impact of those identified fire risk issues where possible, and (3) to review current fire regulations and plant implementation practices for relevance to the identified unaddressed fire risk issues. In performance of the fire risk scenario requantifications several important insights were gained. It was found that utilization of a more extensive operational experience base resulted in both fire occurrence frequencies and fire duration times (i.e., time required for fire suppression) increasing significantly over those assumed in the original works. Additionally, some thermal damage threshold limits assumed in the original works were identified as being nonconservative based on more recent experimental data. Finally, application of the COMPBRN III fire growth model resulted in calculation of considerably longer fire damage times than those calculated in the original works using COMPBRN I. 14 refs., 2 figs., 16 tabs

  6. Targeting Alzheimer's disease by investigating previously unexplored chemical space surrounding the cholinesterase inhibitor donepezil

    CSIR Research Space (South Africa)

    Van Greunen, DG

    2017-02-01

    Full Text Available A series of twenty seven acetylcholinesterase inhibitors, as potential agents for the treatment of Alzheimer's disease, were designed and synthesised based upon previously unexplored chemical space surrounding the molecular skeleton of the drug...

  7. Novel methods for tendon investigations

    DEFF Research Database (Denmark)

    Kjær, Michael; Langberg, Henning; Bojsen-Møller, J.

    2008-01-01

    Purpose. Tendon structures have been studied for decades, but over the last decade, methodological development and renewed interest for metabolic, circulatory and tissue protein turnover in tendon tissue has resulted in a rising amount of investigations. Method. This paper will detail the various...... modern investigative techniques available to study tendons. Results. There are a variety of investigative methods available to study the correlations between mechanics and biology in tendons. Conclusion. The available methodologies not only allow for potential insight into physiological...... and pathophysiological mechanisms in tendon tissue, but also, to some extent, allow for more elaborate studies of the intact human tendon. Read More: http://informahealthcare.com/doi/full/10.1080/09638280701785403...

  8. A method for acetylcholinesterase staining of brain sections previously processed for receptor autoradiography.

    Science.gov (United States)

    Lim, M M; Hammock, E A D; Young, L J

    2004-02-01

    Receptor autoradiography using selective radiolabeled ligands allows visualization of brain receptor distribution and density on film. The resolution of specific brain regions on the film often can be difficult to discern owing to the general spread of the radioactive label and the lack of neuroanatomical landmarks on film. Receptor binding is a chemically harsh protocol that can render the tissue virtually unstainable by Nissl and other conventional stains used to delineate neuroanatomical boundaries of brain regions. We describe a method for acetylcholinesterase (AChE) staining of slides previously processed for receptor binding. AChE staining is a useful tool for delineating major brain nuclei and tracts. AChE staining on sections that have been processed for receptor autoradiography provides a direct comparison of brain regions for more precise neuroanatomical description. We report a detailed thiocholine protocol that is a modification of the Koelle-Friedenwald method to amplify the AChE signal in brain sections previously processed for autoradiography. We also describe several temporal and experimental factors that can affect the density and clarity of the AChE signal when using this protocol.

  9. Nuclear methods in entomological investigations

    International Nuclear Information System (INIS)

    Sethi, G.R.; Bhatia, Parvathy

    1979-01-01

    Insect pests of crops are responsible for immense crop losses in agriculture. Ever since the release of high yielding varieties and improved crop husbandry practices the problems posed by insect pests have been accentuated, as these conditions provide ideal environment for their development. Effective control of insect pests can help greatly in achieving a breakthrough in agricultural production. In order to sustain production and reduce crop losses entomologists all over the world have continued their efforts to devise and develop methods of pest control taking full advantage of the advances made in other branches of science. Consequently, avenues opened by the developments in the field of nuclear energy have also been fully exploited in investigating various pest problems. This communication briefly highlights the various areas of research in which nuclear toots have been fruitfutty used in investigating problems posed by insect pests. (auth.)

  10. [A brief history of resuscitation - the influence of previous experience on modern techniques and methods].

    Science.gov (United States)

    Kucmin, Tomasz; Płowaś-Goral, Małgorzata; Nogalski, Adam

    2015-02-01

    Cardiopulmonary resuscitation (CPR) is relatively novel branch of medical science, however first descriptions of mouth-to-mouth ventilation are to be found in the Bible and literature is full of descriptions of different resuscitation methods - from flagellation and ventilation with bellows through hanging the victims upside down and compressing the chest in order to stimulate ventilation to rectal fumigation with tobacco smoke. The modern history of CPR starts with Kouwenhoven et al. who in 1960 published a paper regarding heart massage through chest compressions. Shortly after that in 1961Peter Safar presented a paradigm promoting opening the airway, performing rescue breaths and chest compressions. First CPR guidelines were published in 1966. Since that time guidelines were modified and improved numerously by two leading world expert organizations ERC (European Resuscitation Council) and AHA (American Heart Association) and published in a new version every 5 years. Currently 2010 guidelines should be obliged. In this paper authors made an attempt to present history of development of resuscitation techniques and methods and assess the influence of previous lifesaving methods on nowadays technologies, equipment and guidelines which allow to help those women and men whose life is in danger due to sudden cardiac arrest. © 2015 MEDPRESS.

  11. Investigation of Transverse Oscillation Method

    DEFF Research Database (Denmark)

    Udesen, Jesper; Jensen, Jørgen Arendt

    2006-01-01

    focus depth, receive apodization, pulse length, transverse wave length, number of emissions, signal to noise ratio, and type of echo canceling filter used. Using the experimental scanner RASMUS, the performance of the TO method is evaluated. An experimental flowrig is used to create laminar parabolic...... direction. Also the choice of echo canceling filter affects the performance significantly....

  12. Method for restoring contaminants to base levels in previously leached formations

    International Nuclear Information System (INIS)

    Strom, E.T.; Espencheid, W.F.

    1983-01-01

    The present invention relates to a method for restoring to environmentally acceptable levels the soluble contaminants in a subterranean formation that has been subjected to oxidative leaching. The contaminants are defined as those ionic species that when subjected to calcium ions form precipitates which are insoluble in the formation fluids. In accordance with the present invention, soluble calcium values are introduced into the formation. The level of contaminants is monitored and when such reaches the desired level, the introduction of soluble calcium values is stopped. The introduction of calcium values may be achieved in several ways one of which is to inject into the formation an aqueous solution containing therein solubilized calcium values. Another method of introducing calcium values into a formation, is to inject into the formation an aqueous solution containing carbon dioxide to solubilize calcium values, such as calcium carbonates, found in the formation

  13. What Is the Correct Answer about The Dress' Colors? Investigating the Relation between Optimism, Previous Experience, and Answerability.

    Science.gov (United States)

    Karlsson, Bodil S A; Allwood, Carl Martin

    2016-01-01

    The Dress photograph, first displayed on the internet in 2015, revealed stunning individual differences in color perception. The aim of this study was to investigate if lay-persons believed that the question about The Dress colors was answerable. Past research has found that optimism is related to judgments of how answerable knowledge questions with controversial answers are (Karlsson et al., 2016). Furthermore, familiarity with a question can create a feeling of knowing the answer (Reder and Ritter, 1992). Building on these findings, 186 participants saw the photo of The Dress and were asked about the correct answer to the question about The Dress' colors (" blue and black," "white and gold," "other, namely…," or "there is no correct answer" ). Choice of the alternative "there is no correct answer" was interpreted as believing the question was not answerable. This answer was chosen more often by optimists and by people who reported they had not seen The Dress before. We also found that among participants who had seen The Dress photo before, 19%, perceived The Dress as "white and gold" but believed that the correct answer was "blue and black ." This, in analogy to previous findings about non-believed memories (Scoboria and Pascal, 2016), shows that people sometimes do not believe the colors they have perceived are correct. Our results suggest that individual differences related to optimism and previous experience may contribute to if the judgment of the individual perception of a photograph is enough to serve as a decision basis for valid conclusions about colors. Further research about color judgments under ambiguous circumstances could benefit from separating individual perceptual experience from beliefs about the correct answer to the color question. Including the option "there is no correct answer " may also be beneficial.

  14. Deciding on the mode of birth after a previous caesarean section - An online survey investigating women's preferences in Western Switzerland.

    Science.gov (United States)

    Bonzon, Magali; Gross, Mechthild M; Karch, André; Grylka-Baeschlin, Susanne

    2017-07-01

    promoting vaginal births after caesarean section (VBAC) for eligible women and increasing rates of successful VBACs are the best strategies to reduce the number of repeat caesarean sections (CS). Knowledge of factors that are associated with women's decision-making around mode of birth after CS is important when developing strategies to promote VBAC. This study assessed which factors are associated with women's preferences for VBAC versus elective repeat caesarean section (ERCS) in a new pregnancy after one previous caesarean in Switzerland. cross-sectional web-survey. Western Switzerland. French-speaking women living in Western Switzerland, with one previous CS who gave birth subsequently to a child after a complication-free pregnancy were eligible to participate in the survey. Of 393 women who started the survey in November/December 2014, 349 were included: 227 who planned a VBAC and 122 who planned an ERCS at term. univariable and multivariable analyses were conducted to describe and compare women who had planned a VBAC with women who had planned an ERCS in a pregnancy following a CS. Logistic regression modelling was used to investigate predictors that were associated with a preference for a VBAC at term. Analyses were performed with SPSS 22 and Stata 13. of the women planning a VBAC, 62.6% VBAC gave birth vaginally. Predictors which were significantly associated with increased odds of women choosing a VBAC: duration since previous birth in years (OR=1.11 95% CI [1.03-1.20], p=0.010), having had midwifery care during pregnancy (OR=2.09, 95% CI [1.08-4.05], p=0.029), being advised by their healthcare provider to attempt a VBAC (OR=4.20, 95% CI [1.75-10.09], p=0.001), preference for VBAC during the third trimester of their pregnancy (OR=3.98, 95% CI [1.77-8.93], p=0.001), and wishing to let the child choose the moment of birth (OR=1.46, 95% CI[1.22-1.74], p<0.001). The importance of safety for the mother decreased the odds of women preferring a VBAC (OR=0.74, 95

  15. The influence of previous subject experience on interactions during peer instruction in an introductory physics course: A mixed methods analysis

    Science.gov (United States)

    Vondruska, Judy A.

    Over the past decade, peer instruction and the introduction of student response systems has provided a means of improving student engagement and achievement in large-lecture settings. While the nature of the student discourse occurring during peer instruction is less understood, existing studies have shown student ideas about the subject, extraneous cues, and confidence level appear to matter in the student-student discourse. Using a mixed methods research design, this study examined the influence of previous subject experience on peer instruction in an introductory, one-semester Survey of Physics course. Quantitative results indicated students in discussion pairs where both had previous subject experience were more likely to answer clicker question correctly both before and after peer discussion compared to student groups where neither partner had previous subject experience. Students in mixed discussion pairs were not statistically different in correct response rates from the other pairings. There was no statistically significant difference between the experience pairs on unit exam scores or the Peer Instruction Partner Survey. Although there was a statistically significant difference between the pre-MPEX and post-MPEX scores, there was no difference between the members of the various subject experience peer discussion pairs. The qualitative study, conducted after the quantitative study, helped to inform the quantitative results by exploring the nature of the peer interactions through survey questions and a series of focus groups discussions. While the majority of participants described a benefit to the use of clickers in the lecture, their experience with their discussion partners varied. Students with previous subject experience tended to describe peer instruction more positively than students who did not have previous subject experience, regardless of the experience level of their partner. They were also more likely to report favorable levels of comfort with

  16. An investigation of the vortex method

    Energy Technology Data Exchange (ETDEWEB)

    Pryor, Jr., Duaine Wright [Univ. of California, Berkeley, CA (United States)

    1994-05-01

    The vortex method is a numerical scheme for solving the vorticity transport equation. Chorin introduced modern vortex methods. The vortex method is a Lagrangian, grid free method which has less intrinsic diffusion than many grid schemes. It is adaptive in the sense that elements are needed only where the vorticity is non-zero. Our description of vortex methods begins with the point vortex method of Rosenhead for two dimensional inviscid flow, and builds upon it to eventually cover the case of three dimensional slightly viscous flow with boundaries. This section gives an introduction to the fundamentals of the vortex method. This is done in order to give a basic impression of the previous work and its line of development, as well as develop some notation and concepts which will be used later. The purpose here is not to give a full review of vortex methods or the contributions made by all the researchers in the field. Please refer to the excellent review papers in Sethian and Gustafson, chapters 1 Sethian, 2 Hald, 3 Sethian, 8 Chorin provide a solid introduction to vortex methods, including convergence theory, application in two dimensions and connection to statistical mechanics and polymers. Much of the information in this review is taken from those chapters, Chorin and Marsden and Batchelor, the chapters are also useful for their extensive bibliographies.

  17. Reference Values for Spirometry Derived Using Lambda, Mu, Sigma (LMS) Method in Korean Adults: in Comparison with Previous References.

    Science.gov (United States)

    Jo, Bum Seak; Myong, Jun Pyo; Rhee, Chin Kook; Yoon, Hyoung Kyu; Koo, Jung Wan; Kim, Hyoung Ryoul

    2018-01-15

    The present study aimed to update the prediction equations for spirometry and their lower limits of normal (LLN) by using the lambda, mu, sigma (LMS) method and to compare the outcomes with the values of previous spirometric reference equations. Spirometric data of 10,249 healthy non-smokers (8,776 females) were extracted from the fourth and fifth versions of the Korea National Health and Nutrition Examination Survey (KNHANES IV, 2007-2009; V, 2010-2012). Reference equations were derived using the LMS method which allows modeling skewness (lambda [L]), mean (mu [M]), and coefficient of variation (sigma [S]). The outcome equations were compared with previous reference values. Prediction equations were presented in the following form: predicted value = e{a + b × ln(height) + c × ln(age) + M - spline}. The new predicted values for spirometry and their LLN derived using the LMS method were shown to more accurately reflect transitions in pulmonary function in young adults than previous prediction equations derived using conventional regression analysis in 2013. There were partial discrepancies between the new reference values and the reference values from the Global Lung Function Initiative in 2012. The results should be interpreted with caution for young adults and elderly males, particularly in terms of the LLN for forced expiratory volume in one second/forced vital capacity in elderly males. Serial spirometry follow-up, together with correlations with other clinical findings, should be emphasized in evaluating the pulmonary function of individuals. Future studies are needed to improve the accuracy of reference data and to develop continuous reference values for spirometry across all ages. © 2018 The Korean Academy of Medical Sciences.

  18. What Is the Correct Answer about The Dress’ Colors? Investigating the Relation between Optimism, Previous Experience, and Answerability

    OpenAIRE

    Karlsson, Bodil S. A.; Allwood, Carl Martin

    2016-01-01

    The Dress photograph, first displayed on the internet in 2015, revealed stunning individual differences in color perception. The aim of this study was to investigate if lay-persons believed that the question about The Dress colors was answerable. Past research has found that optimism is related to judgments of how answerable knowledge questions with controversial answers are (Karlsson et al., 2016). Furthermore, familiarity with a question can create a feeling of knowing the answer (Reder and...

  19. Investigation equipment and methods used by Posiva

    International Nuclear Information System (INIS)

    Oehberg, A.

    2006-10-01

    Posiva Oy, a company jointly owned by TVO and Fortum, submitted an application for the Decision in Principle to the Finnish Government in May 1999. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the Decision in Principle on the final disposal facility for spent nuclear fuel at Olkiluoto, Eurajoki in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground research facility, ONKALO, for rock characterisation for the final disposal of spent nuclear fuel will be constructed. The construction of the ONKALO access tunnel was started in September 2004. This report describes the investigation methods and equipment developed and used by Posiva Oy during the confirming site investigations from the surface. The report covers the areas of drilling of deep investigation holes, geophysical loggings, geophysical ground and tunnel surveys, hydrogeological and hydrogeochemical as well as rock mechanical methods. Emphasis is given on those equipment and methods developed by Posiva and those that have frequently and recently been used in the Posiva's characterisation programmes including methods applied during excavation of ONKALO access tunnel. The database used for the field investigation data is also briefly described in this report. (orig.)

  20. Research Investigation of Information Access Methods

    Science.gov (United States)

    Heinrichs, John H.; Sharkey, Thomas W.; Lim, Jeen-Su

    2006-01-01

    This study investigates the satisfaction of library users at Wayne State University who utilize alternative information access methods. The LibQUAL+[TM] desired and perceived that satisfaction ratings are used to determine the user's "superiority gap." By focusing limited library resources to address "superiority gap" issues identified by each…

  1. Site investigations. Investigation methods and general execution programme

    International Nuclear Information System (INIS)

    2001-01-01

    at least one deep chemistry-prioritized cored borehole, and start of long-term monitoring of chemical parameters in new selected sampling points. Fracture-filling mineral investigations are initiated during the final phase of the initial site investigation. The transport properties of the rock are estimated mainly on the basis of the hydrogeological and hydrogeochemical description, combined with generic, non-site-specific information. Furthermore, supplementary measurements of groundwater flow are performed in one of the first deep boreholes. In cases where mineralogy and/or groundwater chemistry differs significantly from the generic database, certain time-consuming laboratory investigations such as through diffusion measurements will be initiated. A large number of methods are used to investigate the geology of the site. They can be described in general terms under the headings: geophysics, surface geology, soil geology, bedrock geology, borehole investigations and geodetic measurements. The thermal properties of the rock are determined primarily on the basis of mineral composition and by means of laboratory studies of recovered rock cores. The determination of the transport properties of the rock is based on generic, non-site-specific data, combined with he hydrogeological and hydrogeochemical description of the rock. Laboratory measurements on drill cores and rock material are used to determine/verify sorption values and diffusivities. Diffusion tests and tracer tests in and between boreholes can be used to verify the reasonableness of estimated parameter values. The discipline surface ecosystems includes both the living environment, i.e. animals and plants, and their interactions with the non-living environment, e.g. climate and water. The characterization includes both hydrogeological and hydrogeochemical characterization of soil strata and surface waters and inventory/characterization of flora and fauna

  2. Site investigations. Investigation methods and general execution programme

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-01-01

    characterization of at least one deep chemistry-prioritized cored borehole, and start of long-term monitoring of chemical parameters in new selected sampling points. Fracture-filling mineral investigations are initiated during the final phase of the initial site investigation. The transport properties of the rock are estimated mainly on the basis of the hydrogeological and hydrogeochemical description, combined with generic, non-site-specific information. Furthermore, supplementary measurements of groundwater flow are performed in one of the first deep boreholes. In cases where mineralogy and/or groundwater chemistry differs significantly from the generic database, certain time-consuming laboratory investigations such as through diffusion measurements will be initiated. A large number of methods are used to investigate the geology of the site. (abstract truncated)

  3. Investigation of enviromental objects by microanalysis methods

    OpenAIRE

    Osīte, Agnese

    2008-01-01

    Investigation of environmental objects by microanalysis methods AEROSOL PARTICLES, SOOT, METALLIC ELEMENTS, WATER, PINE NEEDLES, STRIPPING POTENTIOMETRY, INDUCTIVELY COUPLED PLASMA MASSPECTROMETRY, ENERGY DISPERIVE X-RAY FLUORESCENCE Performing the fractionated sampling by both commercially available and laboratory constructed devices, mass concentrations of four fractions of solid particles PM10, PM2.5-10, PM2.5 and PM1 were determined. Mass concentrations of soot were ...

  4. Investigating methods of stream planform identification

    Science.gov (United States)

    Lohberg, M. M.; Lusk, K.; Miller, D.; Stonedahl, F.; Stonedahl, S. H.

    2013-12-01

    Stream planforms are used to map scientific measurements, estimate volumetric discharge, and model stream flow. Changes in these planforms can be used to quantify erosion and water level fluctuations. This research investigated five cost-effective methods of identifying stream planforms: (1) consumer-grade digital camera GPS (2) multi-view stereo 3D scene reconstruction (using Microsoft Photosynth (TM)) (3) a cross-sectional measurement approach (4) a triangulation-based measurement approach and (5) the 'square method' - a novel photogrammetric procedure which involved floating a large wooden square in the stream, photographing the square and banks from numerous angles and then using the square to correct for perspective and extract the outline (using custom post-processing software). Data for each of the five methods was collected at Blackhawk Creek in Davenport, Iowa. Additionally we placed 30 control points near the banks of the stream and measured 88 lengths between these control points. We measured or calculated the locations of these control points with each of our five methods and calculated the average percent error associated with each method using the predicted control point locations. The effectiveness of each method was evaluated in terms of accuracy, affordability, environmental intrusiveness, and ease of use. The camera equipped with GPS proved to be a very ineffective method due to an extremely high level of error, 289%. The 3D point cloud extracted from Photosynth was missing markers for many of the control points, so the error calculation (which yielded 11.7%) could only be based on five of the 88 lengths and is thus highly uncertain. The two non-camera methods (cross-sectional and triangulation measurements) resulted in low percent error (2.04% and 1.31% respectively) relative to the control point lengths, but these methods were very time consuming, exhausting, and only provided low resolution outlines. High resolution data collection would

  5. Investigation of methods for hydroclimatic data homogenization

    Science.gov (United States)

    Steirou, E.; Koutsoyiannis, D.

    2012-04-01

    We investigate the methods used for the adjustment of inhomogeneities of temperature time series covering the last 100 years. Based on a systematic study of scientific literature, we classify and evaluate the observed inhomogeneities in historical and modern time series, as well as their adjustment methods. It turns out that these methods are mainly statistical, not well justified by experiments and are rarely supported by metadata. In many of the cases studied the proposed corrections are not even statistically significant. From the global database GHCN-Monthly Version 2, we examine all stations containing both raw and adjusted data that satisfy certain criteria of continuity and distribution over the globe. In the United States of America, because of the large number of available stations, stations were chosen after a suitable sampling. In total we analyzed 181 stations globally. For these stations we calculated the differences between the adjusted and non-adjusted linear 100-year trends. It was found that in the two thirds of the cases, the homogenization procedure increased the positive or decreased the negative temperature trends. One of the most common homogenization methods, 'SNHT for single shifts', was applied to synthetic time series with selected statistical characteristics, occasionally with offsets. The method was satisfactory when applied to independent data normally distributed, but not in data with long-term persistence. The above results cast some doubts in the use of homogenization procedures and tend to indicate that the global temperature increase during the last century is between 0.4°C and 0.7°C, where these two values are the estimates derived from raw and adjusted data, respectively.

  6. Hydrochemical laboratory methods for Nagra's investigation programme

    International Nuclear Information System (INIS)

    Kussmaul, H.; Antonsen, O.

    1985-01-01

    Nagra's geological research program is directed toward determination of the possibilities for depositing high level radioactive waste at depth in Northern Switzerland. The program includes ground water analyses for chemical and biological constituents (analyses by Institut Fresenius) as well as for dissolved gases, uranium, and natural radioactivity (analyses by EIR, Eidgenoessisches Institut fuer Reaktorforschung). Two sources were utilized to obtain formation water chemistry in the study area. A regional program was established to investigate mineral and thermal waters. 17 sites of the regional program are scheduled for long term monitoring of water chemistry. A deep drilling program (12 locations projected) was initiated to obtain and analyze water samples from defined depths and formations under in situ conditions. Chapter 2 presents the analytical programs in detail. General chemistry was determined in all samples. In the regional program, well equipped wells and springs provided representative samples at most locations (cf chapter 3). However, at other locations impairment of sample quality could not be avoided. Given sufficient water flow, samples for the deep drilling program were taken both at the earth's surface under atmospheric pressure conditions (from artesian outflow or after pumping), and under formation pressure at various depths with specialized sample containers (chapter 3.7.3). Chapter 4 gives a listing of all analytical methods used in the study, their accuracy ranges and detection limits. Finally, this paper also presents some special problems encountered during the deep drilling program (cf chapter 5). Preliminary results show that no single method can provide completely satisfactory results for all deep drilling water sampling. A combination of procedures and critical evaluation of their respective data can, however, provide valuable information on the chemistry of waters from certain formations. (author)

  7. Multi-method investigation of cushion peatlands (

    Science.gov (United States)

    Forbriger, M.; Schittek, K.; Höfle, B.; Siart, C.; Eitel, B.

    2012-04-01

    This study presents a multi-method and multi-proxy approach for palaeonvironmental investigations in the western andean cordillera of southern Peru (Lucanas province, 14° S) using cushion peatlands as terrestrial geoarchives. The region stretching between the Altiplano and the Peruvian desert in the lowland shares a long term settlement history, in which local cultures adapted to climate change in many different ways. Being one of the most outstanding human remains, the abri below Cerro Llamoca, 4.450 m a.s.l. in the uppermost ranges of the Llamoca peatland catchment area further reveals an occupation history of almost 10.000 years, as revealed by latest archaeological investigations. In remote and highly elevated regions such as the central Andes, cushion peatlands basically represent the only high resolution terrestrial archives suitable for geoarchaeological and palaeoenvironmental studies. Characterized by high accumulation rates, they ideally document environmental changes, particularly at small time intervals. Within the multidisciplinary project 'Andean Transect - Climate Sensitivity of pre-Columbian Man-Environment-Systems' several sediment cores with depths up to 11.5 m b.s. were recovered from the Llamoca peatland. Based on almost 100 AMS 14C-datings they provide a chronology of 8000 years and, thus, offer profound insights into climatic and environmental changes in the study area. While nearly homogeneous peat layers record stable environmental conditions, the heterogeneous granulometric composition of intercalated sediment layers documents several periods of intense geomorphodynamic activity. Due to high resolution geochemical analyses of peat layers (1 cm interval; humification degree, CNS measurements, XRF-scanning), the existence of slight and short-term trends of landscape development during these phases can be identified. Additional pollen, charred particles and plant macrofossil analyses confirm these findings and help reconstructing local

  8. Locating previously unknown patterns in data-mining results: a dual data- and knowledge-mining method

    Directory of Open Access Journals (Sweden)

    Knaus William A

    2006-03-01

    Full Text Available Abstract Background Data mining can be utilized to automate analysis of substantial amounts of data produced in many organizations. However, data mining produces large numbers of rules and patterns, many of which are not useful. Existing methods for pruning uninteresting patterns have only begun to automate the knowledge acquisition step (which is required for subjective measures of interestingness, hence leaving a serious bottleneck. In this paper we propose a method for automatically acquiring knowledge to shorten the pattern list by locating the novel and interesting ones. Methods The dual-mining method is based on automatically comparing the strength of patterns mined from a database with the strength of equivalent patterns mined from a relevant knowledgebase. When these two estimates of pattern strength do not match, a high "surprise score" is assigned to the pattern, identifying the pattern as potentially interesting. The surprise score captures the degree of novelty or interestingness of the mined pattern. In addition, we show how to compute p values for each surprise score, thus filtering out noise and attaching statistical significance. Results We have implemented the dual-mining method using scripts written in Perl and R. We applied the method to a large patient database and a biomedical literature citation knowledgebase. The system estimated association scores for 50,000 patterns, composed of disease entities and lab results, by querying the database and the knowledgebase. It then computed the surprise scores by comparing the pairs of association scores. Finally, the system estimated statistical significance of the scores. Conclusion The dual-mining method eliminates more than 90% of patterns with strong associations, thus identifying them as uninteresting. We found that the pruning of patterns using the surprise score matched the biomedical evidence in the 100 cases that were examined by hand. The method automates the acquisition of

  9. Qualitative Research Methods to Advance Research on Health Inequities among Previously Incarcerated Women Living with HIV in Alabama

    Science.gov (United States)

    Sprague, Courtenay; Scanlon, Michael L.; Pantalone, David W.

    2017-01-01

    Justice-involved HIV-positive women have poor health outcomes that constitute health inequities. Researchers have yet to embrace the range of qualitative methods to elucidate how psychosocial histories are connected to pathways of vulnerability to HIV and incarceration for this key population. We used life course narratives and…

  10. Investigation of rare elements by electrochemical methods

    International Nuclear Information System (INIS)

    Zarinskij, V.A.

    1988-01-01

    The use of electrochemical methods for the study of complexing, separation of rare element mixtures, their preparation in lower oxidation states, and also for the development of highly sensitive methods of the element determination, is considered in the review. Voltammetric methods of Pt, Au, Re determination are considered, as well as Re preparation in oxidation states +5, +3 by electrolytic methods. The possibility to use electrodialysis methods for purification of insoluble compounds of rare earths (RE) from impurities, and for separation of Re and Mo with simultaneous purification of Re from K and other elements is shown. The application of high-frequency conductometry to analytic chemistry and to the study of Th, In, RE complexing and kinetics of the reactions is considered

  11. Investigation into Methods for Predicting Connection Temperatures

    Directory of Open Access Journals (Sweden)

    K. Anderson

    2009-01-01

    Full Text Available The mechanical response of connections in fire is largely based on material strength degradation and the interactions between the various components of the connection. In order to predict connection performance in fire, temperature profiles must initially be established in order to evaluate the material strength degradation over time. This paper examines two current methods for predicting connection temperatures: The percentage method, where connection temperatures are calculated as a percentage of the adjacent beam lower-flange, mid-span temperatures; and the lumped capacitance method, based on the lumped mass of the connection. Results from the percentage method do not correlate well with experimental results, whereas the lumped capacitance method shows much better agreement with average connection temperatures. A 3D finite element heat transfer model was also created in Abaqus, and showed good correlation with experimental results. 

  12. THE INFLUENCE OF THE ASSESSMENT MODEL AND METHOD TOWARD THE SCIENCE LEARNING ACHIEVEMENT BY CONTROLLING THE STUDENTS? PREVIOUS KNOWLEDGE OF MATHEMATICS.

    OpenAIRE

    Adam rumbalifar; I. g. n. Agung; Burhanuddin tola.

    2018-01-01

    This research aims to study the influence of the assessment model and method toward the science learning achievement by controlling the students? previous knowledge of mathematics. This study was conducted at SMP East Seram district with the population of 295 students. This study applied a quasi-experimental method with 2 X 2 factorial design using the ANCOVA model. The findings after controlling the students\\' previous knowledge of mathematics show that the science learning achievement of th...

  13. Investigating alternative dispute resolution methods and the ...

    African Journals Online (AJOL)

    provide a clear definition; 69.4% of architectural professionals do not discuss. ADR methods ..... The study used a quantitative research approach, as the research involves .... questions. The findings of the data might also identify possible gaps.

  14. Investigating hydrogel dosimeter decomposition by chemical methods

    International Nuclear Information System (INIS)

    Jordan, Kevin

    2015-01-01

    The chemical oxidative decomposition of leucocrystal violet micelle hydrogel dosimeters was investigated using the reaction of ferrous ions with hydrogen peroxide or sodium bicarbonate with hydrogen peroxide. The second reaction is more effective at dye decomposition in gelatin hydrogels. Additional chemical analysis is required to determine the decomposition products

  15. Investigating alternative dispute resolution methods and the ...

    African Journals Online (AJOL)

    This article investigates the current knowledge, implementation and benefits of ADR within the South African built environment. The focus population of the study is architectural professionals, as defined by the South African Council for the Architectural Profession (SACAP). A questionnaire was distributed among 581 ...

  16. Satellite Magnetic Residuals Investigated With Geostatistical Methods

    DEFF Research Database (Denmark)

    Fox Maule, Chaterine; Mosegaard, Klaus; Olsen, Nils

    2005-01-01

    (which consists of measurement errors and unmodeled signal), and is typically assumed to be uncorrelated and Gaussian distributed. We have applied geostatistical methods to analyze the residuals of the Oersted (09d/04) field model (www.dsri.dk/Oersted/Field models/IGRF 2005 candidates/), which is based...

  17. Bomb-Pulse Chlorine-36 At The Proposed Yucca Mountain Repository Horizon: An Investigation Of Previous Conflicting Results And Collection Of New Data

    International Nuclear Information System (INIS)

    J. Cizdziel

    2006-01-01

    Previous studies by scientists at Los Alamos National Laboratory (LANL) found elevated ratios of chlorine-36 to total chloride ( 36 Cl/Cl) in samples of rock collected from the Exploratory Studies Facility (ESF) and the Enhanced Characterization of the Repository Block (ECRB) at Yucca Mountain as the tunnels were excavated. The data were interpreted as an indication that fluids containing 'bomb-pulse' 36 Cl reached the repository horizon in the ∼50 years since the peak period of above-ground nuclear testing. Moreover, the data support the concept that so-called fast pathways for infiltration not only exist but are active, possibly through a combination of porous media, faults and/or other geologic features. Due to the significance of 36 Cl data to conceptual models of unsaturated zone flow and transport, the United States Geological Survey (USGS) was requested by the Department of Energy (DOE) to design and implement a study to validate the LANL findings. The USGS chose to drill new boreholes at select locations across zones where bomb-pulse ratios had previously been identified. The drill cores were analyzed at Lawrence Livermore National Laboratory (LLNL) for 36 Cl/Cl using both active and passive leaches, with the USGS/LLNL concluding that the active leach extracted too much rock-Cl and the passive leach did not show bomb-pulse ratios. Because consensus was not reached between the USGS/LLNL and LANL on several fundamental points, including the conceptual strategy for sampling, interpretation and use of tritium ( 3 H) data, and the importance and interpretation of blanks, in addition to the presence or absence of bomb-pulse 36 Cl, an evaluation by an independent entity, the University of Nevada, Las Vegas (UNLV), using new samples was initiated. This report is the result of that study. The overall objectives of the UNLV study were to investigate the source or sources of the conflicting results from the previous validation study, and to obtain additional data to

  18. Investigation of mixed saliva by optoelectronic methods

    Science.gov (United States)

    Savchenko, Ekaterina; Nepomnyashchaya, Elina; Baranov, Maksim; Velichko, Elena; Aksenov, Evgenii; Bogomaz, Tatyana

    2018-04-01

    At present, saliva and its properties are being actively studied. Human saliva is a unique biological material that has potential in clinical practice. A detailed analysis of the characteristics and properties of saliva is relevant for diagnostic purposes. In this paper, the properties and characteristics of saliva are studied using optoelectronic methods: dynamic light scattering, electrophoretic light scattering and optical microscopy. Mixed saliva from a healthy patient and patient with diabetes mellitus type 2 was used as an object of the study. The dynamics of the behavior of a healthy and patient with diabetes mellitus type 2 is visible according to the results obtained. All three methods confirm hypothesis of structural changes in mixed saliva in the disease of diabetes mellitus type 2.

  19. Use of isotope methods for glacialhydrological investigations

    International Nuclear Information System (INIS)

    Moser, H.

    1986-01-01

    Glacialhydrological investigations at Vernagtferner (Oetztal Alps, Austria) by means of measurements of 2 H, 18 O, and 3 H contents as well as of electrolytic conductivity yield quantitative data on the different discharge portions in the glacier stream and on residence times in the different storage volumes within the glacier. Hence it follows a detailed picture of the glacier discharge system, which can be simulated by a mathematical model. The total calculated glacier discharge values derived from the energy balance at the glacier surface and from the storage coefficients, are in a satisfying agreement with the measured total glacier discharges for the period 1978-1983 hitherto evaluated. (author)

  20. Investigating of the Knocking Out Properties of Moulding Sands with New Inorganic Binders Used for Castings of Non-ferrous Metal Alloys in Comparison with the Previously Used

    Directory of Open Access Journals (Sweden)

    I. Izdebska-Szanda

    2012-12-01

    Full Text Available The article presents the results of investigations, which make a fragment of the broad-scale studies carried out as a part of the projectPOIG.01.01.02-00-015/09 “Advanced materials and technologies”.One of the objectives of the introduction of new inorganic binders is to provide a good knocking out properties of moulding sands, whilemaintaining an appropriate level of strength properties.Therefore, a logical continuation of the previous studies were carried out the tests knocking out properties of moulding sands with newinorganic binders, including making moulds, pouring them by the chosen of non-ferrous metal alloys, knoking-out, and determining theknocking out work.The results of the study were related to the research results obtained by applying the moulding sand performed by existing technology.

  1. A preliminary investigation of PSA validation methods

    Energy Technology Data Exchange (ETDEWEB)

    Unwin, S D [Science Applications International Corp., (United States)

    1995-09-01

    This document has been prepared to support the initial phase of the Atomic Energy Control Board`s program to review and evaluate Probabilistic Safety Assessment (PSA) studies conducted by nuclear generating station designers and licensees. The document provides (1) a review of current and prospective applications of PSA technology in the Canadian nuclear power industry; (2) an assessment of existing practices and techniques for the review or risk and hazard identification studies in the international nuclear power sector and other technological sectors; and (3) proposed analytical framework in which to develop systematic techniques for the scrutiny and evaluation of a PSA model. These frameworks are based on consideration of the mathematical structure of a PSA model and are intended to facilitate the development of methods to evaluate a model relative to intended end-uses. (author). 34 refs., 10 tabs., 3 figs.

  2. A preliminary investigation of PSA validation methods

    International Nuclear Information System (INIS)

    Unwin, S.D.

    1995-09-01

    This document has been prepared to support the initial phase of the Atomic Energy Control Board's program to review and evaluate Probabilistic Safety Assessment (PSA) studies conducted by nuclear generating station designers and licensees. The document provides (1) a review of current and prospective applications of PSA technology in the Canadian nuclear power industry; (2) an assessment of existing practices and techniques for the review or risk and hazard identification studies in the international nuclear power sector and other technological sectors; and (3) proposed analytical framework in which to develop systematic techniques for the scrutiny and evaluation of a PSA model. These frameworks are based on consideration of the mathematical structure of a PSA model and are intended to facilitate the development of methods to evaluate a model relative to intended end-uses. (author). 34 refs., 10 tabs., 3 figs

  3. Porosimetry as an effective method of fuel cell investigation

    Energy Technology Data Exchange (ETDEWEB)

    Kazarinov, V.E.

    1996-04-01

    A porosimetric method is described for the investigation of all kinds of porous materials including soft or frail materials and powders. The method is well suited for the investigation of electrodes in fuel cells and batteries. The method is nondestructive and allows for repeated measurements on the same sample.

  4. Aespoe Hard Rock Laboratory - feasibility and usefulness of site investigation methods. Experiences from the pre-investigation phase

    Energy Technology Data Exchange (ETDEWEB)

    Almen, K E [ed.; KEA GEO-Konsult (Sweden); Olsson, Paer [SKANSKA, (Sweden); Rhen, I [VBB VIAK AB, Malmoe (Sweden); Stanfors, R [RS Consulting, (Sweden); Wikberg, P [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

    1994-08-01

    One of the main goals set up by SKB for the Aespoe HRL project is to `test the quality and appropriateness of different methods for characterizing the bedrock with respect to conditions of importance for a final repository`. An extensive investigation programme was carried out during the projects pre-investigation phase that in part was based in experience from SKBs previous site investigations and in part entailed the testing of new or other unestablished methods. Previous technical reports have described the methods that have been used and the results, models and predictions that have been produced. All the methods used are discussed in the present report in terms of how they have contributed in different analysis stages to the total geoscientific characterization of the rock at Aespoe. The usefulness of each method for modelling and prediction in different scales is evaluated, and aspects of the practical execution of the methods under different conditions are discussed. The report sheds light on the importance of dividing large investigation programmes such as this one into suitable stages to get an opportunity to evaluate the results obtained and plan in detail the investigations in the next stage. Furthermore, the way in which the characterization/modelling work in different geometric scales has been done for the different investigation stages is discussed, along with whether this has been found to be a suitable approach. The importance of pursuing an interdisciplinary strategy throughout the pre-investigation process cannot be overemphasized. For the planning, execution, analysis and reporting of the results of the pre-investigations, this has been guaranteed by an organization in which an interdisciplinary group has been in charge of the investigations, together with the project manager. 52 refs, numerous tabs and figs.

  5. Revisiting chlorophyll extraction methods in biological soil crusts - methodology for determination of chlorophyll a and chlorophyll a + b as compared to previous methods

    Science.gov (United States)

    Caesar, Jennifer; Tamm, Alexandra; Ruckteschler, Nina; Lena Leifke, Anna; Weber, Bettina

    2018-03-01

    Chlorophyll concentrations of biological soil crust (biocrust) samples are commonly determined to quantify the relevance of photosynthetically active organisms within these surface soil communities. Whereas chlorophyll extraction methods for freshwater algae and leaf tissues of vascular plants are well established, there is still some uncertainty regarding the optimal extraction method for biocrusts, where organism composition is highly variable and samples comprise major amounts of soil. In this study we analyzed the efficiency of two different chlorophyll extraction solvents, the effect of grinding the soil samples prior to the extraction procedure, and the impact of shaking as an intermediate step during extraction. The analyses were conducted on four different types of biocrusts. Our results show that for all biocrust types chlorophyll contents obtained with ethanol were significantly lower than those obtained using dimethyl sulfoxide (DMSO) as a solvent. Grinding of biocrust samples prior to analysis caused a highly significant decrease in chlorophyll content for green algal lichen- and cyanolichen-dominated biocrusts, and a tendency towards lower values for moss- and algae-dominated biocrusts. Shaking of the samples after each extraction step had a significant positive effect on the chlorophyll content of green algal lichen- and cyanolichen-dominated biocrusts. Based on our results we confirm a DMSO-based chlorophyll extraction method without grinding pretreatment and suggest the addition of an intermediate shaking step for complete chlorophyll extraction (see Supplement S6 for detailed manual). Determination of a universal chlorophyll extraction method for biocrusts is essential for the inter-comparability of publications conducted across all continents.

  6. Revisiting chlorophyll extraction methods in biological soil crusts – methodology for determination of chlorophyll a and chlorophyll a + b as compared to previous methods

    Directory of Open Access Journals (Sweden)

    J. Caesar

    2018-03-01

    Full Text Available Chlorophyll concentrations of biological soil crust (biocrust samples are commonly determined to quantify the relevance of photosynthetically active organisms within these surface soil communities. Whereas chlorophyll extraction methods for freshwater algae and leaf tissues of vascular plants are well established, there is still some uncertainty regarding the optimal extraction method for biocrusts, where organism composition is highly variable and samples comprise major amounts of soil. In this study we analyzed the efficiency of two different chlorophyll extraction solvents, the effect of grinding the soil samples prior to the extraction procedure, and the impact of shaking as an intermediate step during extraction. The analyses were conducted on four different types of biocrusts. Our results show that for all biocrust types chlorophyll contents obtained with ethanol were significantly lower than those obtained using dimethyl sulfoxide (DMSO as a solvent. Grinding of biocrust samples prior to analysis caused a highly significant decrease in chlorophyll content for green algal lichen- and cyanolichen-dominated biocrusts, and a tendency towards lower values for moss- and algae-dominated biocrusts. Shaking of the samples after each extraction step had a significant positive effect on the chlorophyll content of green algal lichen- and cyanolichen-dominated biocrusts. Based on our results we confirm a DMSO-based chlorophyll extraction method without grinding pretreatment and suggest the addition of an intermediate shaking step for complete chlorophyll extraction (see Supplement S6 for detailed manual. Determination of a universal chlorophyll extraction method for biocrusts is essential for the inter-comparability of publications conducted across all continents.

  7. A Comparative Investigation of the Previous and New Secondary History Curriculum: The Issues of the Definition of the Aims and Objectives and the Selection of Curriculum Content

    Science.gov (United States)

    Dinc, Erkan

    2011-01-01

    Discussions on history teaching in Turkey indicate that the previous versions of the history curriculum and the pedagogy of history in the country bear many problems and deficiencies. The problems of Turkish history curriculum mainly arise from the perspectives it takes and the selection of its content. Since 2003, there have been extensive…

  8. An automated patient recognition method based on an image-matching technique using previous chest radiographs in the picture archiving and communication system environment

    International Nuclear Information System (INIS)

    Morishita, Junji; Katsuragawa, Shigehiko; Kondo, Keisuke; Doi, Kunio

    2001-01-01

    An automated patient recognition method for correcting 'wrong' chest radiographs being stored in a picture archiving and communication system (PACS) environment has been developed. The method is based on an image-matching technique that uses previous chest radiographs. For identification of a 'wrong' patient, the correlation value was determined for a previous image of a patient and a new, current image of the presumed corresponding patient. The current image was shifted horizontally and vertically and rotated, so that we could determine the best match between the two images. The results indicated that the correlation values between the current and previous images for the same, 'correct' patients were generally greater than those for different, 'wrong' patients. Although the two histograms for the same patient and for different patients overlapped at correlation values greater than 0.80, most parts of the histograms were separated. The correlation value was compared with a threshold value that was determined based on an analysis of the histograms of correlation values obtained for the same patient and for different patients. If the current image is considered potentially to belong to a 'wrong' patient, then a warning sign with the probability for a 'wrong' patient is provided to alert radiology personnel. Our results indicate that at least half of the 'wrong' images in our database can be identified correctly with the method described in this study. The overall performance in terms of a receiver operating characteristic curve showed a high performance of the system. The results also indicate that some readings of 'wrong' images for a given patient in the PACS environment can be prevented by use of the method we developed. Therefore an automated warning system for patient recognition would be useful in correcting 'wrong' images being stored in the PACS environment

  9. Doppler method leak detection for LMFBR steam generators. Pt. 3. Investigation of detection sensitivity and method

    International Nuclear Information System (INIS)

    Kumagai, Hiromichi; Kinoshita, Izumi

    2001-01-01

    To prevent the expansion of tube damage and to maintain structural integrity in the steam generators (SGs) of a fast breeder reactor (FBR), it is necessary to detect precisely and immediately any leakage of water from heat transfer tubes. Therefore, the Doppler method was developed. Previous studies have revealed that, in the SG full-sector model that simulates actual SGs, the Doppler method can detect bubbles of 0.4 l/s within a few seconds. However in consideration of the dissolution rate of hydrogen generated by a sodium-water reaction even from a small water leak, it is necessary to detect smaller leakages of water from the heat transfer tubes. The detection sensitivity of the Doppler method and the influence of background noise were experimentally investigated. In-water experiments were performed using the SG model. The results show that the Doppler method can detect bubbles of 0.01 l/s (equivalent to a water leak rate of about 0.01 g/s) within a few seconds and that the background noise has little effect on water leak detection performance. The Doppler method thus has great potential for the detection of water leakage in SGs. (author)

  10. Laparoscopy After Previous Laparotomy

    Directory of Open Access Journals (Sweden)

    Zulfo Godinjak

    2006-11-01

    Full Text Available Following the abdominal surgery, extensive adhesions often occur and they can cause difficulties during laparoscopic operations. However, previous laparotomy is not considered to be a contraindication for laparoscopy. The aim of this study is to present that an insertion of Veres needle in the region of umbilicus is a safe method for creating a pneumoperitoneum for laparoscopic operations after previous laparotomy. In the last three years, we have performed 144 laparoscopic operations in patients that previously underwent one or two laparotomies. Pathology of digestive system, genital organs, Cesarean Section or abdominal war injuries were the most common causes of previouslaparotomy. During those operations or during entering into abdominal cavity we have not experienced any complications, while in 7 patients we performed conversion to laparotomy following the diagnostic laparoscopy. In all patients an insertion of Veres needle and trocar insertion in the umbilical region was performed, namely a technique of closed laparoscopy. Not even in one patient adhesions in the region of umbilicus were found, and no abdominal organs were injured.

  11. Investigating Convergence Patterns for Numerical Methods Using Data Analysis

    Science.gov (United States)

    Gordon, Sheldon P.

    2013-01-01

    The article investigates the patterns that arise in the convergence of numerical methods, particularly those in the errors involved in successive iterations, using data analysis and curve fitting methods. In particular, the results obtained are used to convey a deeper level of understanding of the concepts of linear, quadratic, and cubic…

  12. Lymphoscintigraphy for sentinel lymph node mapping in Japanese patients with malignant skin neoplasms of the lower extremities. Comparison with previously investigated Japanese lymphatic anatomy

    International Nuclear Information System (INIS)

    Miura, Hiroyuki; Ono, Shuichi; Nagahata, Morio

    2010-01-01

    Lymph nodes (LN) and lymphatic drainage were identified by lymphoscintigraphy using 99m Tc-phytate in order to map the sentinel lymph nodes (SLNs) in patients with malignant skin neoplasms of the lower extremities, and to compare the results with an atlas of Japanese lymphatic anatomy. Sentinel lymphoscintigraphs of 18 patients with malignant skin neoplasms of the lower extremities (9 men, 9 women; age range 45-84 years, mean age 66 years) were analyzed retrospectively, and the LNs detected were identified as SLNs or secondary nodes. The patterns of lymphatic drainage were divided into three different categories: initial drainage into inguinal LN without visualization of popliteal LNs (inguinal type), initial drainage into popliteal LNs and then into intrapelvic LNs (popliteal type), and initial drainage into both popliteal and inguinal LNs (inguinal and popliteal type). More than half of the cases were the inguinal and popliteal type, as both inguinal and popliteal LNs were identified as SLNs. In the cases in which the hallux and its surrounding area were injected, all were the inguinal type and popliteal LNs were not visualized. In one case, only dynamic images detected lymphatic drainage without visualization of popliteal LNs. In contrast to the previously published literature on Japanese lymphatic anatomy, SLN lymphatic drainage from the skin of the lower extremities was wide and overlapping in many areas. However, in agreement with currently accepted anatomy, only the great saphenous lymphatic vessel drained the skin of the hallux and its surrounding area. The present results suggest that it is important to confirm lymphatic drainage in order to identify SLNs in the lower extremities. The patterns of lymphatic drainage from the skin of the foot were divided into three different categories. In contrast to previously published Japanese lymphatic anatomy, lymphatic drainage from the skin of the lower extremities was wide and overlapping in many areas. However

  13. Investigations on application of multigrid method to MHD equilibrium analysis

    International Nuclear Information System (INIS)

    Ikuno, Soichiro

    2000-01-01

    The potentiality of application for Multi-grid method to MHD equilibrium analysis is investigated. The nonlinear eigenvalue problem often appears when the MHD equilibria are determined by solving the Grad-Shafranov equation numerically. After linearization of the equation, the problem is solved by use of the iterative method. Although the Red-Black SOR method or Gauss-Seidel method is often used for the solution of the linearized equation, it takes much CPU time to solve the problem. The Multi-grid method is compared with the SOR method for the Poisson Problem. The results of computations show that the CPU time required for the Multi-grid method is about 1000 times as small as that for the SOR method. (author)

  14. Latest groundwater investigating methods and measuring techniques. 1. ; Investigation on aquifer distribution (investigation method). Saikin no chikasui chosa hoho to keisoku gijutsu. 1. ; Taisuiso no bunpu chosa (tansaho)

    Energy Technology Data Exchange (ETDEWEB)

    Yamai, T [Asia Air Survey Co. Ltd., Tokyo (Japan)

    1993-06-30

    This paper explains groundwater investigating methods, introducing particularly two methods. The resistivity tomography is a method to measure potential distribution generated when current is applied around an area to be investigated. Using the measurement result as projection data, the resistivity distribution is restructured within the area of the investigation. The paper summarizes the measurement method (measuring equipment, electrode arrangement, etc.), the analytic method (establishment of an initial model, and the alpha-center method to calculate theoretical potentials corresponding to the model), and an application example of the method in which the resistivity change was observed using permeation of salt tracers. The resistivity imaging method (two-dimensional resistivity analysis method) is superior in practicability to the above method under the present state of the art. This method does not differ from the conventional resistivity method in methodology, but improves the analytic accuracy over the conventional electrical investigation method as a result of analysis combining the simplified two-dimensional analysis method with the alpha-center method. A summary is given on the measuring and analyzing methods. 13 refs., 10 figs.

  15. Treatment response in psychotic patients classified according to social and clinical needs, drug side effects, and previous treatment; a method to identify functional remission.

    Science.gov (United States)

    Alenius, Malin; Hammarlund-Udenaes, Margareta; Hartvig, Per; Sundquist, Staffan; Lindström, Leif

    2009-01-01

    Various approaches have been made over the years to classify psychotic patients according to inadequate treatment response, using terms such as treatment resistant or treatment refractory. Existing classifications have been criticized for overestimating positive symptoms; underestimating residual symptoms, negative symptoms, and side effects; or being to open for individual interpretation. The aim of this study was to present and evaluate a new method of classification according to treatment response and, thus, to identify patients in functional remission. A naturalistic, cross-sectional study was performed using patient interviews and information from patient files. The new classification method CANSEPT, which combines the Camberwell Assessment of Need rating scale, the Udvalg for Kliniske Undersøgelser side effect rating scale (SE), and the patient's previous treatment history (PT), was used to group the patients according to treatment response. CANSEPT was evaluated by comparison of expected and observed results. In the patient population (n = 123), the patients in functional remission, as defined by CANSEPT, had higher quality of life, fewer hospitalizations, fewer psychotic symptoms, and higher rate of workers than those with the worst treatment outcome. In the evaluation, CANSEPT showed validity in discriminating the patients of interest and was well tolerated by the patients. CANSEPT could secure inclusion of correct patients in the clinic or in research.

  16. Investigating requests and expectations for future methods of CEE

    DEFF Research Database (Denmark)

    Nørgaard, Bente; Jensson, Palle; Bayard, Ove

    2014-01-01

    This article presents a map of requests and expectations for future ‘delivery’ methods of continuing engineering education (CEE) viewed from the perspective of Scandinavian managing directors and their employed engineers. During the last decades numerous attempts have been made to develop new...... into the crystal ball to identify requests and expectations to future methods of CEE. The significance of the investigation will be a conceptual map, which discloses some future focus areas ahead of CEE providers....

  17. Investigation of the paired-gear method in selectivity studies

    DEFF Research Database (Denmark)

    Sistiaga, Manu; Herrmann, Bent; Larsen, R.B.

    2009-01-01

    was repeated throughout the eight cases in this investigation. When using the paired-gear method, the distribution of the estimated L50 and SR is wider; the distribution of the estimated split parameter has a higher variability than the true split; the estimated mean L50 and SR can be biased; the estimated...... recommend that the methodology used to obtain selectivity estimates using the paired-gear method be reviewed....

  18. An investigation of calibration methods for solution calorimetry.

    Science.gov (United States)

    Yff, Barbara T S; Royall, Paul G; Brown, Marc B; Martin, Gary P

    2004-01-28

    Solution calorimetry has been used in a number of varying applications within pharmaceutical research as a technique for the physical characterisation of pharmaceutical materials, such as quantifying small degrees of amorphous content, identifying polymorphs and investigating interactions between drugs and carbohydrates or proteins and carbohydrates. A calibration test procedure is necessary to validate the instrumentation; a few of the suggested calibration reactions are the enthalpies of solution associated with dissolving Tris in 0.1 M HCl or NaCl, KCl or propan-1-ol in water. In addition, there are a number of different methods available to determine enthalpies of solution from the experimental data provided by the calorimeter, for example, the Regnault-Pfaundler's method, a graphical extrapolation based on the Dickinson method, or a manual integration-based method. Thus, the aim of the study was to investigate how each of these methods influences the values for the enthalpy of solution. Experiments were performed according to the method outlined by Hogan and Buckton [Int. J. Pharm. 207 (2000) 57] using KCl (samples of 50, 100 and 200 mg), Tris and sucrose as calibrants. For all three materials the manual integration method was found to be the most consistent with the KCl in water (sample mass of 200 mg) being the most precise. Thus, this method is recommended for the validation of solution calorimeters.

  19. Comparison of different methods to investigate postprandial lipaemia

    NARCIS (Netherlands)

    van Oostrom, A. J. H. H. M.; Alipour, A.; Sijmonsma, T. P.; Verseyden, C.; Dallinga-Thie, G. M.; Plokker, H. W. M.; Castro Cabezas, M.

    2009-01-01

    Postprandial hyperlipidaemia has been associated with coronary artery disease (CAD). We investigated which of the generally used methods to test postprandial lipaemia differentiated best between patients with premature CAD (50 +/- 4 years, n=20) and healthy controls. Furthermore, the effects of

  20. A sequential mixed methods research approach to investigating HIV ...

    African Journals Online (AJOL)

    Sequential mixed methods research is an effective approach for investigating complex problems, but it has not been extensively used in construction management research. In South Africa, the HIV/AIDS pandemic has seen construction management taking on a vital responsibility since the government called upon the ...

  1. Investigation of radiation defects in solids using the EXAFS method

    International Nuclear Information System (INIS)

    Eritsyan, G.N.

    1983-01-01

    The exafs method is proposed as a more informative, universal one to investigate the radiation defects in solids. The successful results as obtained by the author using the synchrotron radiation source are reported for the first time. The measurements were carried out in GaAsP crystals irradiated with 50 MeV electrons

  2. MACROECONOMIC POLICY OF CURRENCY WAR: METHODS OF INVESTIGATION

    Directory of Open Access Journals (Sweden)

    Bekareva S. V.

    2015-12-01

    Full Text Available The article is devoted to the methods of investigation of a modern international monetary and finance field for some countries which would participate in currency war. Usually currency wars are used in order to achieve some competitive advantages in international trade relations. Real effective exchange rate index was used as the key instrument in our analysis. It reflects a nominal exchange rate and the main trade partners’ structure as well. Moreover, some macroeconomic and finance indices were used. The methods of investigation are cluster and panel data analyses. The period of investigation is 1990-2012. The result of analysis is connected with showing differences in countries’ possibility of implementing monetary policy instruments to improve their competitiveness.

  3. Development and Investigation of Reactivity Measurement Methods in Subcritical Cores

    Energy Technology Data Exchange (ETDEWEB)

    Wright, Johanna

    2005-05-01

    Subcriticality measurements during core loading and in future accelerator driven systems have a clear safety relevance. In this thesis two subcriticality methods are treated: the Feynman-alpha and the source modulation method. The Feynman-alpha method is a technique to determine the reactivity from the relative variance of the detector counts during a measurement period. The period length is varied to get the full time dependence of the variance-to-mean. The corresponding theoretical formula was known only with stationary sources. In this thesis, due to its relevance for novel reactivity measurement methods, the Feynman-alpha formulae for pulsed sources for both the stochastic and the deterministic cases are treated. Formulae neglecting as well as including the delayed neutrons are derived. The formulae neglecting delayed neutrons are experimentally verified with quite good agreement. The second reactivity measurement technique investigated in this thesis is the so-called source modulation technique. The theory of the method was elaborated on the assumption of point kinetics, but in practice the method will be applied by using the signal from a single local neutron detector. Applicability of the method therefore assumes point kinetic behaviour of the core. Hence, first the conditions of the point kinetic behaviour of subcritical cores was investigated. After that the performance of the source modulation technique in the general case as well as and in the limit of exact point kinetic behaviour was examined. We obtained the unexpected result that the method has a finite, non-negligible error even in the limit of point kinetic behaviour, and a substantial error in the operation range of future accelerator driven subcritical reactors (ADS). In practice therefore the method needs to be calibrated by some other method for on-line applications.

  4. Development and Investigation of Reactivity Measurement Methods in Subcritical Cores

    International Nuclear Information System (INIS)

    Wright, Johanna

    2005-05-01

    Subcriticality measurements during core loading and in future accelerator driven systems have a clear safety relevance. In this thesis two subcriticality methods are treated: the Feynman-alpha and the source modulation method. The Feynman-alpha method is a technique to determine the reactivity from the relative variance of the detector counts during a measurement period. The period length is varied to get the full time dependence of the variance-to-mean. The corresponding theoretical formula was known only with stationary sources. In this thesis, due to its relevance for novel reactivity measurement methods, the Feynman-alpha formulae for pulsed sources for both the stochastic and the deterministic cases are treated. Formulae neglecting as well as including the delayed neutrons are derived. The formulae neglecting delayed neutrons are experimentally verified with quite good agreement. The second reactivity measurement technique investigated in this thesis is the so-called source modulation technique. The theory of the method was elaborated on the assumption of point kinetics, but in practice the method will be applied by using the signal from a single local neutron detector. Applicability of the method therefore assumes point kinetic behaviour of the core. Hence, first the conditions of the point kinetic behaviour of subcritical cores was investigated. After that the performance of the source modulation technique in the general case as well as and in the limit of exact point kinetic behaviour was examined. We obtained the unexpected result that the method has a finite, non-negligible error even in the limit of point kinetic behaviour, and a substantial error in the operation range of future accelerator driven subcritical reactors (ADS). In practice therefore the method needs to be calibrated by some other method for on-line applications

  5. Investigation of Thermal Performance for Atria: a Method Overview

    Directory of Open Access Journals (Sweden)

    Moosavi Leila

    2016-01-01

    Full Text Available The importance of low energy design in large buildings has encouraged researchers to implement different methods for predicting a building’s thermal performance. Atria, as energy efficient features, have been implemented to improve the indoor thermal environment in large modern buildings. Though widely implemented, the thorough study of atrium performance is restricted due to its large size, complex thermodynamic behavior and the inaccuracies and limitations of available prediction tools. This study reviews the most common research tools implemented in previous researches on atria thermal performance, to explore the advantages and limitation of different methods for future studies. The methods reviewed are analytical, experimental, computer modelling and a combination of any or all of these methods. The findings showed that CFD (computational fluid dynamic models are the most popular tools of recent due to their higher accuracy, capabilities and user-friendly modification. Although the experimental methods were reliable for predicting atria thermal and ventilation performance, they have mostly been used to provide data for validation of CFD models. Furthermore, coupling CFD with other experimental models could increase the reliability and accuracy of the models and provide a more comprehensive analysis.

  6. Experimental method for investigating helium effects in irradiated vanadium

    International Nuclear Information System (INIS)

    Smith, D.L.; Matsui, H.; Greenwood, L.; Loomis, B.

    1987-10-01

    Analyses have been performed which indicate that an effective method for experimentally investigating helium effects in neutron irradiated vanadium base alloys can be developed. The experimental procedure involves only modest modifications to existing procedures currently used for irradiation testing of vanadium-base alloys in the FFTF reactor. Helium is generated in the vanadium alloy by decay of tritium which is either preinjected or generated within the test capsule. Calculations indicate that nearly constant He/dpa ratios of desired magnitude can be attained by proper selection of experimental parameters. The proposed method could have a major impact on the development of vanadium base alloys for fusion reactor applications. 8 refs., 4 figs

  7. CFT and RTD methods for wastewater treatment plants apparatus investigation

    International Nuclear Information System (INIS)

    Palige, J.; Owczarczyk, A.; Dobrowolski, A.; Ptaszek, S.

    2006-01-01

    Two methods, residence time distributions (RTD) and computational fluid dynamics (CFD) are most effective for solid and wastewater phases investigations of flow dynamics. On the basis of measured (in tracer experiment) RTD function, the model of flow can be proposed for the unit under investigation. The experimental and numerical RTD functions were compared for different technological parameters values of processes (apparatus geometry, flow rate, location and construction of input and output). Numerical RTD function was obtained by DRW (discrete random walk) technique - determination of residence times of many liquid particles. The usefulness of these techniques was checked on a large scale laboratory model of settler. Satisfactory agreement of the data obtained by both methods - tracer and CFD - was observed

  8. The experience sampling method: Investigating students' affective experience

    Science.gov (United States)

    Nissen, Jayson M.; Stetzer, MacKenzie R.; Shemwell, Jonathan T.

    2013-01-01

    Improving non-cognitive outcomes such as attitudes, efficacy, and persistence in physics courses is an important goal of physics education. This investigation implemented an in-the-moment surveying technique called the Experience Sampling Method (ESM) [1] to measure students' affective experience in physics. Measurements included: self-efficacy, cognitive efficiency, activation, intrinsic motivation, and affect. Data are presented that show contrasts in students' experiences (e.g., in physics vs. non-physics courses).

  9. Serial sectioning methods for 3D investigations in materials science.

    Science.gov (United States)

    Zankel, Armin; Wagner, Julian; Poelt, Peter

    2014-07-01

    A variety of methods for the investigation and 3D representation of the inner structure of materials has been developed. In this paper, techniques based on slice and view using scanning microscopy for imaging are presented and compared. Three different methods of serial sectioning combined with either scanning electron or scanning ion microscopy or atomic force microscopy (AFM) were placed under scrutiny: serial block-face scanning electron microscopy, which facilitates an ultramicrotome built into the chamber of a variable pressure scanning electron microscope; three-dimensional (3D) AFM, which combines an (cryo-) ultramicrotome with an atomic force microscope, and 3D FIB, which delivers results by slicing with a focused ion beam. These three methods complement one another in many respects, e.g., in the type of materials that can be investigated, the resolution that can be obtained and the information that can be extracted from 3D reconstructions. A detailed review is given about preparation, the slice and view process itself, and the limitations of the methods and possible artifacts. Applications for each technique are also provided. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Investigation on generalized Variational Nodal Methods for heterogeneous nodes

    International Nuclear Information System (INIS)

    Wang, Yongping; Wu, Hongchun; Li, Yunzhao; Cao, Liangzhi; Shen, Wei

    2017-01-01

    Highlights: • We developed two heterogeneous nodal methods based on the Variational Nodal Method. • Four problems were solved to evaluate the two heterogeneous nodal methods. • The function expansion method is good at treating continuous-changing heterogeneity. • The finite sub-element method is good at treating discontinuous-changing heterogeneity. - Abstract: The Variational Nodal Method (VNM) is generalized for heterogeneous nodes and applied to four kinds of problems including Molten Salt Reactor (MSR) core problem with continuous cross section profile, Pressurized Water Reactor (PWR) control rod cusping effect problem, PWR whole-core pin-by-pin problem, and heterogeneous PWR core problem without fuel-coolant homogenization in each pin cell. Two approaches have been investigated for the treatment of the nodal heterogeneity in this paper. To concentrate on spatial heterogeneity, diffusion approximation was adopted for the angular variable in neutron transport equation. To provide demonstrative numerical results, the codes in this paper were developed in slab geometry. The first method, named as function expansion (FE) method, expands nodal flux by orthogonal polynomials and the nodal cross sections are also expressed as spatial depended functions. The second path, named as finite sub-element (FS) method, takes advantage of the finite-element method by dividing each node into numbers of homogeneous sub-elements and expanding nodal flux into the combination of linear sub-element trial functions. Numerical tests have been carried out to evaluate the ability of the two nodal (coarse-mesh) heterogeneous VNMs by comparing with the fine-mesh homogeneous VNM. It has been demonstrated that both heterogeneous approaches can handle heterogeneous nodes. The FE method is good at continuous-changing heterogeneity as in the MSR core problem, while the FS method is good at discontinuous-changing heterogeneity such as the PWR pin-by-pin problem and heterogeneous PWR core

  11. A method to investigate the diffusion properties of nuclear calcium.

    Science.gov (United States)

    Queisser, Gillian; Wittum, Gabriel

    2011-10-01

    Modeling biophysical processes in general requires knowledge about underlying biological parameters. The quality of simulation results is strongly influenced by the accuracy of these parameters, hence the identification of parameter values that the model includes is a major part of simulating biophysical processes. In many cases, secondary data can be gathered by experimental setups, which are exploitable by mathematical inverse modeling techniques. Here we describe a method for parameter identification of diffusion properties of calcium in the nuclei of rat hippocampal neurons. The method is based on a Gauss-Newton method for solving a least-squares minimization problem and was formulated in such a way that it is ideally implementable in the simulation platform uG. Making use of independently published space- and time-dependent calcium imaging data, generated from laser-assisted calcium uncaging experiments, here we could identify the diffusion properties of nuclear calcium and were able to validate a previously published model that describes nuclear calcium dynamics as a diffusion process.

  12. Investigations into the myocardial metabolism of 123-I-ω-HDA in patients showing the clinical signs and symptoms of mitral valve prolapse and previously proven to have no coronary heart disease

    International Nuclear Information System (INIS)

    Voth, E.

    1987-01-01

    In 53 patients showing the clinical signs and symptoms of mitral valve prolapse (MVP) where coronary heart disease (CHD) had previously been excluded by angiography the myocardial metabolism of fatty acids was examined at rest using metabolic myocardial scintigraphy (MMS) and 123-I-ω-HDA as tracer substance. The results were correlated with those obtained by other methods of investigation (findings at rest and during exercise from ECG recordings, tests using a flow-guided catheter and radionuclide ventriculography, further from echocardiography as well as myocardial Tl redistribution scintiscanning during exercise). For purposes of reference, MMS was additionally carried out in twelve normal individuals subjected to coronary angiography to exclude both MVP and CHD. The results of this study would appear to suggest that the pathological findings revealed by myocardial Tl scintigraphy in patients showing symptoms of MVP cannot invariably be classified as 'false' but are at least to some extent attributable to impaired myocardial perfusion, vitality or metabolism. (orig./MG) [de

  13. Investigation of Evaluation method of chemical runaway reaction

    International Nuclear Information System (INIS)

    Sato, Yoshihiko; Sasaya, Shinji; Kurakata, Koichiro; Nojiri, Ichiro

    2002-02-01

    Safety study 'Study of evaluation of abnormal occurrence for chemical substances in the nuclear fuel facilities' will be carried out from 2001 to 2005. In this study, the prediction of thermal hazards of chemical substances will be investigated and prepared. The hazard prediction method of chemical substances will be constructed from these results. Therefore, the hazard prediction methods applied in the chemical engineering in which the chemical substances with the hazard of fire and explosion were often treated were investigated. CHETAH (The ASTM Computer Program for Chemical Thermodynamic and Energy Release Evaluation) developed by ASTM (American Society for Testing and Materials) and TSS (Thermal Safety Software) developed by CISP (ChemInform St. Petersburg) were introduced and the fire and explosion hazards of chemical substances and reactions in the reprocessing process were evaluated. From these evaluated results, CHETAH could almost estimate the heat of reaction at 10% accuracy. It was supposed that CHETAH was useful as a screening for the hazards of fire and explosion of the new chemical substances and so on. TSS could calculate the reaction rate and the reaction behavior from the data measured by the various calorimeters rapidly. It was supposed that TSS was useful as an evaluation method for the hazards of fire and explosion of the new chemical reactions and so on. (author)

  14. Investigation of evaluation methods for human factors education effectiveness

    International Nuclear Information System (INIS)

    Yoshimura, Seiichi; Fujimoto, Junzo; Sasou Kunihide; Hasegawa, Naoko

    2004-01-01

    Education effectiveness in accordance with investment is required in the steam of electric power regulation alleviation. Therefore, evaluation methods for human factors education effectiveness which can observe human factors culture pervading process were investigated through research activities on education effectiveness in universities and actual in house education in industry companies. As a result, the contents of evaluation were found to be the change of feeling for human factors and some improving proposals in work places when considering the purpose of human factors education. And, questionnaire is found to be suitable for the style of evaluation. In addition, the timing of evaluation is desirable for both just after education and after some period in work places. Hereafter, data will be collected using these two kinds of questionnaires in human factors education courses in CRIEPI and some education courses in utilities. Thus, education effectiveness evaluation method which is suitable for human factors will be established. (author)

  15. Investigation of the fuel temperature evaluation method at BOL

    International Nuclear Information System (INIS)

    Ishii, Tetsuya; Asaga, Takeo; Nemoto, Junichi

    1999-06-01

    It is one of the major subjects in the improvement of the design method for determining the thermal conditions of the solid type Mixed - Oxide (MOX) fuels in FBR to evaluate the fuel temperature at BOL as precisely as possible. Therefore, we have planned to modify the fuel temperature evaluation method 'FEVER', which was developed by JNC in 1988, as one of the investigation for the establishment of the precise fuel temperature evaluation method. And, we also have planned to use the modified FEVER, named FEVER-M', for estimation of the irradiation conditions of the PTM test in Joyo, called 'B10 test', planning to perform in 2000. In this work, the following results were obtained; 1) As a result of the modification, the uncertainty in the fuel temperature evaluation of 'FEVER-M' is reduced to about ±60 K. 2) Estimating the irradiation conditions of 'B10' test using the method 'FEVER-M', it is found that the appropriate maximum linear heat rate for the test is 620 W/cm. The detail plans of the 'B10' test were also determined based on the results. 3) Based on the results of this work, it is found that one of the effective procedure for the improvement of the accuracy of the fuel temperature evaluation method seems to calculate the fuel temperature taking the pellet relocation phenomena into account. In future, although there are a lot of matters to be discussed in this phenomena, the design method for the thermal conditions of the MOX fuels in FBR should be performed with taking the pellet relocation phenomena into account. (author)

  16. Methods for investigating biosurfactants and bioemulsifiers: a review.

    Science.gov (United States)

    Satpute, Surekha K; Banpurkar, Arun G; Dhakephalkar, Prashant K; Banat, Ibrahim M; Chopade, Balu A

    2010-06-01

    Microorganisms produce biosurfactant (BS)/bioemulsifier (BE) with wide structural and functional diversity which consequently results in the adoption of different techniques to investigate these diverse amphiphilic molecules. This review aims to compile information on different microbial screening methods, surface active products extraction procedures, and analytical terminologies used in this field. Different methods for screening microbial culture broth or cell biomass for surface active compounds production are also presented and their possible advantages and disadvantages highlighted. In addition, the most common methods for purification, detection, and structure determination for a wide range of BS and BE are introduced. Simple techniques such as precipitation using acetone, ammonium sulphate, solvent extraction, ultrafiltration, ion exchange, dialysis, ultrafiltration, lyophilization, isoelectric focusing (IEF), and thin layer chromatography (TLC) are described. Other more elaborate techniques including high pressure liquid chromatography (HPLC), infra red (IR), gas chromatography-mass spectroscopy (GC-MS), nuclear magnetic resonance (NMR), and fast atom bombardment mass spectroscopy (FAB-MS), protein digestion and amino acid sequencing are also elucidated. Various experimental strategies including static light scattering and hydrodynamic characterization for micelles have been discussed. A combination of various analytical methods are often essential in this area of research and a numbers of trials and errors to isolate, purify and characterize various surface active agents are required. This review introduces the various methodologies that are indispensable for studying biosurfactants and bioemulsifiers.

  17. Investigation of drag effect using the field signature method

    International Nuclear Information System (INIS)

    Wan, Zhengjun; Liao, Junbi; Tian, Gui Yun; Cheng, Liang

    2011-01-01

    The potential drop (PD) method is an established non-destructive evaluation (NDE) technique. The monitoring of internal corrosion, erosion and cracks in piping systems, based on electrical field mapping or direct current potential drop array, is also known as the field signature method (FSM). The FSM has been applied in the field of submarine pipe monitoring and land-based oil and gas transmission pipes and containers. In the experimental studies, to detect and calculate the degree of pipe corrosion, the FSM analyses the relationships between the electrical resistance and pipe thickness using an electrode matrix. The relevant drag effect or trans-resistance will cause a large margin of error in the application of resistance arrays. It is the first time that the drag effect in the paper is investigated and analysed in resistance networks with the help of the FSM. Subsequently, a method to calculate the drag factors and eliminate its errors is proposed and presented. Theoretical analysis, simulation and experimental results show that the measurement accuracy can be improved by eliminating the errors caused by the drag effect

  18. Calorimetric investigations of solids by combined FPPE - TWRC method

    International Nuclear Information System (INIS)

    Dadarlat, D; Streza, M; Pop, M N; Tosa, V; Delenclos, S; Longuemart, S; Sahraoui, A Hadj

    2010-01-01

    An alternative photopyroelectric (PPE) technique that combines the front detection configuration (FPPE) with the thermal-wave-resonator-cavity (TWRC) method is proposed for direct measurement of thermal effusivity of solid materials inserted as backings in the FPPE detection cell. The method uses the scan of the normalized PPE phase as a function of sample's thickness, in the thermally thin regime for the sensor and liquid layer, and thermally thick regime for the backing material. The value of backing's thermal effusivity results from the optimization of the fit of the phase of the signal, performed with sample's thickness and backing's thermal effusivity as fitting parameters. The paper presents experimental results on several solid materials (inserted as backing in the cell), with different values of thermal effusivity (brass, steel, wood) and two liquids (ethylene glycol, water) largely used in the FPPE-TWRC cells. The paper stresses mainly on the sensitivity of the technique to different liquid/backing effusivity ratios. It seems that the method is suitable especially when investigating solids with values of thermal effusivity close to the effusivity of the liquid layer.

  19. A CRITICAL ASSESSMENT OF PHOTOMETRIC REDSHIFT METHODS: A CANDELS INVESTIGATION

    International Nuclear Information System (INIS)

    Dahlen, Tomas; Ferguson, Henry C.; Mobasher, Bahram; Faber, Sandra M.; Barro, Guillermo; Guo, Yicheng; Finkelstein, Steven L.; Finlator, Kristian; Fontana, Adriano; Gruetzbauch, Ruth; Johnson, Seth; Pforr, Janine; Dickinson, Mark E.; Salvato, Mara; Wuyts, Stijn; Wiklind, Tommy; Acquaviva, Viviana; Huang, Jiasheng; Huang, Kuang-Han; Newman, Jeffrey A.

    2013-01-01

    We present results from the Cosmic Assembly Near-infrared Deep Extragalactic Legacy Survey (CANDELS) photometric redshift methods investigation. In this investigation, the results from 11 participants, each using a different combination of photometric redshift code, template spectral energy distributions (SEDs), and priors, are used to examine the properties of photometric redshifts applied to deep fields with broadband multi-wavelength coverage. The photometry used includes U-band through mid-infrared filters and was derived using the TFIT method. Comparing the results, we find that there is no particular code or set of template SEDs that results in significantly better photometric redshifts compared to others. However, we find that codes producing the lowest scatter and outlier fraction utilize a training sample to optimize photometric redshifts by adding zero-point offsets, template adjusting, or adding extra smoothing errors. These results therefore stress the importance of the training procedure. We find a strong dependence of the photometric redshift accuracy on the signal-to-noise ratio of the photometry. On the other hand, we find a weak dependence of the photometric redshift scatter with redshift and galaxy color. We find that most photometric redshift codes quote redshift errors (e.g., 68% confidence intervals) that are too small compared to that expected from the spectroscopic control sample. We find that all codes show a statistically significant bias in the photometric redshifts. However, the bias is in all cases smaller than the scatter; the latter therefore dominates the errors. Finally, we find that combining results from multiple codes significantly decreases the photometric redshift scatter and outlier fraction. We discuss different ways of combining data to produce accurate photometric redshifts and error estimates

  20. Theoretical and experimental investigation of multispectral photoacoustic osteoporosis detection method

    Science.gov (United States)

    Steinberg, Idan; Hershkovich, Hadas Sara; Gannot, Israel; Eyal, Avishay

    2014-03-01

    Osteoporosis is a widespread disorder, which has a catastrophic impact on patients lives and overwhelming related to healthcare costs. Recently, we proposed a multispectral photoacoustic technique for early detection of osteoporosis. Such technique has great advantages over pure ultrasonic or optical methods as it allows the deduction of both bone functionality from the bone absorption spectrum and bone resistance to fracture from the characteristics of the ultrasound propagation. We demonstrated the propagation of multiple acoustic modes in animal bones in-vitro. To further investigate the effects of multiple wavelength excitations and of induced osteoporosis on the PA signal a multispectral photoacoustic system is presented. The experimental investigation is based on measuring the interference of multiple acoustic modes. The performance of the system is evaluated and a simple two mode theoretical model is fitted to the measured phase signals. The results show that such PA technique is accurate and repeatable. Then a multiple wavelength excitation is tested. It is shown that the PA response due to different excitation wavelengths revels that absorption by the different bone constitutes has a profound effect on the mode generation. The PA response is measured in single wavelength before and after induced osteoporosis. Results show that induced osteoporosis alters the measured amplitude and phase in a consistent manner which allows the detection of the onset of osteoporosis. These results suggest that a complete characterization of the bone over a region of both acoustic and optical frequencies might be used as a powerful tool for in-vivo bone evaluation.

  1. Nuclear methods for 'in-situ' geophysical investigations. 2

    International Nuclear Information System (INIS)

    Russell, J.P.; Oliver, D.W.

    1985-01-01

    There has been considerable effort expended by governmental, institutional, and private agencies in the development of suitable materials and instruments for application of nuclear methods for exploration and evaluation of mineral, oil, and gas resources. As a consequence of the peculiar circumstances of in situ investigations, much of the apparatus is, of design and construction, specifically adapted to the environment of the borehole (limited lateral dimension, high temperature and pressure, deep boreholes, etc.) which differs considerably from laboratory conditions. Meeting the needs for reliability and stability under adverse conditions of operation has led to often unique and innovative instrumentation. Much of the development effort has been provided by commercial service organizations whose interests require many details be maintained as proprietary. In addition, the tailoring of services to meet varying environmental and informational constraints has led to a wide range of instrument designs. As a result, it is difficult to provide an exhaustive description of all apparatus available for in situ investigations, rather, in this instance, systems and subsystems will be generically discussed. Radiation sources, detectors, and borehole probe designs are covered. (Auth.)

  2. The investigation of parameters affecting boron removal by electrocoagulation method

    Energy Technology Data Exchange (ETDEWEB)

    Yilmaz, A. Erdem [Department of Environmental Engineering, Atatuerk University, Faculty of Engineering, Erzurum (Turkey)]. E-mail: aerdemy@atauni.edu.tr; Boncukcuoglu, Recep [Department of Environmental Engineering, Atatuerk University, Faculty of Engineering, Erzurum (Turkey); Kocakerim, M. Muhtar [Department of Chemical Engineering, 25240, Atatuerk University, Faculty of Engineering Erzurum (Turkey); Keskinler, Buelent [Department of Environmental Engineering, Gebze Institute of Technology, Gebze/Kocaeli 41400 (Turkey)

    2005-10-17

    Boron removal from wastewaters by electrocoagulation using aluminum electrode material was investigated in this paper. Several working parameters, such as pH, current density, boron concentration and type and concentration of supporting electrolyte were studied in an attempt to achieve a higher removal capacity. The experiments were carried out by keeping the pH of solution constant and optimum pH of solution was determined 8.0 for the aluminum electrode. Although energy consumption increased with decreasing boron concentration, which conductivity of these solutions were low, boron removal efficiency was higher at 100 mg/L than that of 1000 mg/L. Current density was an important parameter affecting removal efficiency. Boron removal efficiency and energy consumption increased with increasing current density from 1.2 to 6.0 mA/cm{sup 2}. The types of different supporting electrolyte were experimented in order to investigate to this parameter effect on boron removal. The highest boron removal efficiency, 97%, was found by CaCl{sub 2}. Added CaCl{sub 2} increased more the conductivity of solution according to other supporting electrolytes, but decreased energy consumption. The results showed to have a high effectiveness of the electrocoagulation method in removing boron from aqueous solutions.

  3. The investigation of parameters affecting boron removal by electrocoagulation method

    International Nuclear Information System (INIS)

    Yilmaz, A. Erdem; Boncukcuoglu, Recep; Kocakerim, M. Muhtar; Keskinler, Buelent

    2005-01-01

    Boron removal from wastewaters by electrocoagulation using aluminum electrode material was investigated in this paper. Several working parameters, such as pH, current density, boron concentration and type and concentration of supporting electrolyte were studied in an attempt to achieve a higher removal capacity. The experiments were carried out by keeping the pH of solution constant and optimum pH of solution was determined 8.0 for the aluminum electrode. Although energy consumption increased with decreasing boron concentration, which conductivity of these solutions were low, boron removal efficiency was higher at 100 mg/L than that of 1000 mg/L. Current density was an important parameter affecting removal efficiency. Boron removal efficiency and energy consumption increased with increasing current density from 1.2 to 6.0 mA/cm 2 . The types of different supporting electrolyte were experimented in order to investigate to this parameter effect on boron removal. The highest boron removal efficiency, 97%, was found by CaCl 2 . Added CaCl 2 increased more the conductivity of solution according to other supporting electrolytes, but decreased energy consumption. The results showed to have a high effectiveness of the electrocoagulation method in removing boron from aqueous solutions

  4. Investigating a method of producing "red and dead" galaxies

    Science.gov (United States)

    Skory, Stephen

    2010-08-01

    , but has memory bottlenecks as the datasets get larger. These bottlenecks inspired the second version, "Parallel HOP," which is a fully parallelized method and implementation of HOP that has worked on datasets with more than 20483 particles on hundreds of processing cores. Both methods are described in detail, as are the various effects of performance-related runtime options. Additionally, both halo finders are subjected to a full suite of performance benchmarks varying both dataset sizes and computational resources used. I conclude with descriptions of four new tools I added to yt. A Parallel Structure Function Generator allows analysis of two-point functions, such as correlation functions, using memory- and workload-parallelism. A Parallel Merger Tree Generator leverages the parallel halo finders in yt, such as Parallel HOP, to build the merger tree of halos in a cosmological simulation, and outputs the result to a SQLite database for simple and powerful data extraction. A Star Particle Analysis toolkit takes a group of star particles and can output the rate of formation as a function of time, and/or a synthetic Spectral Energy Distribution (S.E.D.) using the Bruzual and Charlot (2003) data tables. Finally, a Halo Mass Function toolkit takes as input a list of halo masses and can output the halo mass function for the halos, as well as an analytical fit for those halos using several previously published fits.

  5. Investigation of Reusable Crucibles on Uranium Casting by Injection Method

    International Nuclear Information System (INIS)

    Song, Hoon; Kim, Jong-Hwan; Ko, Young-Mo; Woo, Yoon-Myung; Kim, Ki-Hwan; Lee, Chan-Bock

    2014-01-01

    Slurry applied coatings must be recoated after every batch. Thermal plasma-sprayed coatings of refractory materials can be applied to develop a re-usable crucible coating for metallic fuel. Plasma-sprayed coating can provide a crucible with a denser, more durable, coating layer, compared with the more friable coating layer formed by slurry-coating. Plasma-sprayed coatings are consolidated by mechanical interlocking of the molten particles impacting on the substrate and are dense from the heat applied by the plasma. Although the protective layer is more difficult in a dense coating than in a porous coating, the increased coating density is advantageous because it should not require frequent recoating or U-Zr melt penetration. In this study, we used a Vacuum Plasma Spray (VPS) method, which is suitable to prevent oxidization and has a number of advantages such as low defect density and excellent adhesion of the coating layer, to investigate permanent coatings for re-usable crucibles for melting and casting of metallic fuel. After coatings, interaction studies between molten U-Zr alloys and the plasma sprayed coatings were also carried out. We summarized the results of the coating methods. All coated samples maintained good coating integrity in a U-Zr melt, but most of the coating method samples did not maintain integrity in the U-Zr-RE melt because of the cracks or microcracks of the coating layer, presumably formed from the thermal expansion difference. Only the TaC(100)-Y 2 O 3 (100) DL VPS coated rod survived the 2 cycles dipping test of U-Zr-RE melt. This is likely caused by good adhesion of the TaC coating onto the niobium rod and the chemical inertness of Y 2 O 3 coating material in the U-Zr-RE melt. Based on the results from the interactions with U-10Zr and U-10Zr-5RE melt, TaC(100)-Y 2 O 3 (100) plasma-sprayed coating methods have been applied to real graphite crucibles

  6. Treatment response in psychotic patients classified according to social and clinical needs, drug side effects, and previous treatment; a method to identify functional remission

    DEFF Research Database (Denmark)

    Alenius, Malin; Hammarlund-Udenaes, Margareta; Honoré, Per Gustaf Hartvig

    2009-01-01

    , fewer psychotic symptoms, and higher rate of workers than those with the worst treatment outcome. CONCLUSION: In the evaluation, CANSEPT showed validity in discriminating the patients of interest and was well tolerated by the patients. CANSEPT could secure inclusion of correct patients in the clinic......BACKGROUND: Various approaches have been made over the years to classify psychotic patients according to inadequate treatment response, using terms such as treatment resistant or treatment refractory. Existing classifications have been criticized for overestimating positive symptoms......; underestimating residual symptoms, negative symptoms, and side effects; or being to open for individual interpretation. The aim of this study was to present and evaluate a new method of classification according to treatment response and, thus, to identify patients in functional remission. METHOD: A naturalistic...

  7. MERCURY CONTAMINATED MATERIAL DECONTAMINATION METHODS: INVESTIGATION AND ASSESSMENT

    Energy Technology Data Exchange (ETDEWEB)

    M.A. Ebadian, Ph.D.

    2001-01-01

    Over the years mercury has been recognized as having serious impacts on human health and the environment. This recognition has led to numerous studies that deal with the properties of various mercury forms, the development of methods to quantify and speciate the forms, fate and transport, toxicology studies, and the development of site remediation and decontamination technologies. This report reviews several critical areas that will be used in developing technologies for cleaning mercury from mercury-contaminated surfaces of metals and porous materials found in many DOE facilities. The technologies used for decontamination of water and mixed wastes (solid) are specifically discussed. Many technologies that have recently appeared in the literature are included in the report. Current surface decontamination processes have been reviewed, and the limitations of these technologies for mercury decontamination are discussed. Based on the currently available technologies and the processes published recently in the literature, several processes, including strippable coatings, chemical cleaning with iodine/iodide lixiviant, chemisorbing surface wipes with forager sponge and grafted cotton, and surface/pore fixation through amalgamation or stabilization, have been identified as potential techniques for decontamination of mercury-contaminated metal and porous surfaces. Their potential merits and applicability are discussed. Finally, two processes, strippable coatings and chemical cleaning with iodine/iodide lixiviant, were experimentally investigated in Phase II of this project.

  8. Empathy and childhood maltreatment: a mixed-methods investigation.

    Science.gov (United States)

    Locher, Simon C; Barenblatt, Lisa; Fourie, Melike M; Stein, Dan J; Gobodo-Madikizela, Pumla

    2014-05-01

    Impaired empathy is regarded as a psychological consequence of childhood maltreatment, yet few studies have explored this relationship empirically. We investigated whether empathy differed in healthy and maltreated individuals by examining their emotional responses to people in distress. Forty-nine individuals (age 20 to 60) viewed short film clips from the South African Truth and Reconciliation Commission testimonies depicting dialogues between victims and perpetrators of gross human rights violations. Participants were divided into 3 groups based on their scores on the Childhood Trauma Questionnaire: control (n = 18), moderate maltreatment (n = 21), and severe maltreatment (n = 10). We employed a mixed-methods design to explore empathic responses to film clips both quantitatively and qualitatively. Quantitative results indicated that self-reported empathy was lower in the moderate maltreatment group compared to the control group, but of similar strengths in the severe maltreatment and control groups. However, qualitative thematic analysis indicated that both maltreatment groups displayed themes of impaired empathy. Our results support the notion that childhood maltreatment is associated with impaired empathy, and suggest that such impairment may differ depending on the level of maltreatment: moderate maltreatment was associated with emotional blunting and impaired cognitive empathy, whereas severe maltreatment was associated with emotional over-arousal and diminished cognitive insight.

  9. A method for the investigation of cholegraphic contrast media

    International Nuclear Information System (INIS)

    Otto, H.

    1982-01-01

    Isolated perfused rat livers were used for investigating possible interactions between two simultaneously injected contrast media, and which technique, using parenteral application of cholegraphic media, is optimal. The results show that excretion of a parenteral contrast medium is reduced by giving an oral contrast medium at the same time. Simultaneous administration of two different contrast media therefore does not result in improved diagnostic information. The effect depends on the dose, and a sufficiently long interval should be observed between giving an oral and a parenteral contrast medium. A comparison of excretion values following injection of a bolus and prolonged infusion shows higher biliary contrast concentration and increased excretion after a single injection. Comparing only the period after the infusion, no difference was found between these two methods of administration. The single injection offers pharmacokinetic advantages, but an infusion is better tolerated and has fewer side effects. A rapid infusion of 10 to 15 minutes is therefore recommended as the optimal means of administration. (orig.) [de

  10. MERCURY CONTAMINATED MATERIAL DECONTAMINATION METHODS: INVESTIGATION AND ASSESSMENT; TOPICAL

    International Nuclear Information System (INIS)

    M.A. Ebadian, Ph.D.

    2001-01-01

    Over the years mercury has been recognized as having serious impacts on human health and the environment. This recognition has led to numerous studies that deal with the properties of various mercury forms, the development of methods to quantify and speciate the forms, fate and transport, toxicology studies, and the development of site remediation and decontamination technologies. This report reviews several critical areas that will be used in developing technologies for cleaning mercury from mercury-contaminated surfaces of metals and porous materials found in many DOE facilities. The technologies used for decontamination of water and mixed wastes (solid) are specifically discussed. Many technologies that have recently appeared in the literature are included in the report. Current surface decontamination processes have been reviewed, and the limitations of these technologies for mercury decontamination are discussed. Based on the currently available technologies and the processes published recently in the literature, several processes, including strippable coatings, chemical cleaning with iodine/iodide lixiviant, chemisorbing surface wipes with forager sponge and grafted cotton, and surface/pore fixation through amalgamation or stabilization, have been identified as potential techniques for decontamination of mercury-contaminated metal and porous surfaces. Their potential merits and applicability are discussed. Finally, two processes, strippable coatings and chemical cleaning with iodine/iodide lixiviant, were experimentally investigated in Phase II of this project

  11. Modelling of near-field radionuclide transport phenomena in a KBS-3V type of repository for nuclear waste with Goldsim Code - and verification against previous methods

    International Nuclear Information System (INIS)

    Pulkkanen, V.-M.; Nordman, H.

    2010-03-01

    Traditional radionuclide transport models overestimate significantly some phenomena, or completely ignore them. This motivates the development of new more precise models. As a result, this work is a description of commissioning of a new KBS-3V near-field radionuclide transport model, which has been done with a commercial software called GoldSim. According to earlier models, GoldSim model uses rz coordinates, but the solubilities of radionuclides have been treated more precisely. To begin with, the physical phenomena concerning near-field transport have been introduced according to GoldSim way of thinking. Also, the computational methods of GoldSim have been introduced and compared to methods used earlier. The actual verification of GoldSim model has been carried out by comparing the GoldSim results from simple cases to the corresponding results obtained with REPCOM, a software developed by VTT and used in several safety assessments. The results agree well. Finally, a few complicated cases were studied. In these cases, the REPCOM's limitations in handling of some phenomena become evident. The differences in the results are caused especially by the extension of the solubility limit to the whole computational domain, and the element-wise treatment of the solubilities which was used instead of nuclide-wise treatment. This work has been carried out as a special assignment to the former laboratory of Advanced Energy Systems in Helsinki University of Technology. The work was done at VTT. (orig.)

  12. The effect of changes in core body temperature on the QT interval in beagle dogs: a previously ignored phenomenon, with a method for correction.

    Science.gov (United States)

    van der Linde, H J; Van Deuren, B; Teisman, A; Towart, R; Gallacher, D J

    2008-08-01

    Body core temperature (Tc) changes affect the QT interval, but correction for this has not been systematically investigated. It may be important to correct QT intervals for drug-induced changes in Tc. Anaesthetized beagle dogs were artificially cooled (34.2 degrees C) or warmed (42.1 degrees C). The relationship between corrected QT intervals (QTcV; QT interval corrected according to the Van de Water formula) and Tc was analysed. This relationship was also examined in conscious dogs where Tc was increased by exercise. When QTcV intervals were plotted against changes in Tc, linear correlations were observed in all individual dogs. The slopes did not significantly differ between cooling (-14.85+/-2.08) or heating (-13.12+/-3.46) protocols. We propose a correction formula to compensate for the influence of Tc changes and standardize the QTcV duration to 37.5 degrees C: QTcVcT (QTcV corrected for changes in core temperature)=QTcV-14 (37.5 - Tc). Furthermore, cooled dogs were re-warmed (from 34.2 to 40.0 degrees C) and marked QTcV shortening (-29%) was induced. After Tc correction, using the above formula, this decrease was abolished. In these re-warmed dogs, we observed significant increases in T-wave amplitude and in serum [K(+)] levels. No arrhythmias or increase in pro-arrhythmic biomarkers were observed. In exercising dogs, the above formula completely compensated QTcV for the temperature increase. This study shows the importance of correcting QTcV intervals for changes in Tc, to avoid misleading interpretations of apparent QTcV interval changes. We recommend that all ICH S7A, conscious animal safety studies should routinely measure core body temperature and correct QTcV appropriately, if body temperature and heart rate changes are observed.

  13. Constructing a paleo-DEM in an urban area by the example of the city of Aachen, Germany: Methods and previous results

    Science.gov (United States)

    Pröschel, Bernhard; Lehmkuhl, Frank

    2017-04-01

    Reconstructing paleo-landscapes in urban areas is always a special challenge since the research area often witnessed constant human impact over long time periods. Dense building development is a major difficulty, particularly in regard to accessibility to in-situ soils and archaeological findings. It is therefore necessary to use data from various sources and combine methods from different fields to gain a detailed picture of the former topography. The area, which is occupied by the city of Aachen today, looks back on a long history of human influence. Traces of human activity can be dated back to Neolithic time. The first architectural structures and the first road network were built by the Romans about 2000 years ago. From then on, the area of Aachen was more or less continuously inhabited forming today's city. This long history is represented by archaeological findings throughout the city. Several meters of settlement deposits, covering different eras, are present in many locations. Therefore, it can be assumed that the modern topography significantly differs from the pre-roman topography. The main objective of this project is a reconstruction of the paleo-topography of Aachen in order to gain new insights on the spatial preconditions that the first settlers found. Moreover, further attention is given to the question whether and to what extent a paleo-DEM can help to clarify specific open archaeological and historical questions. The main database for the reconstruction are the archaeological excavation reports of the past 150 years, provided by municipal and regional archives. After analyzing these written accounts, we linked this information to drill data, provided by the Geological Service of North Rhine-Westphalia. Together with additional sources like geological and hydrological maps, we generated a GIS-based terrain model. The result is a high-resolution terrain model, representing the undisturbed pre-roman topography of the inner city of Aachen without any

  14. A sequential mixed methods research approach to investigating HIV ...

    African Journals Online (AJOL)

    2016-09-03

    Sep 3, 2016 ... Sequential mixed methods research is an effective approach for ... show the effectiveness of the research method. ... qualitative data before quantitative datasets ..... whereby both types of data are collected simultaneously.

  15. Development of spraying methods for high density bentonite barriers. Part 3. Field investigation of spraying methods

    International Nuclear Information System (INIS)

    Tanaka, Toshiyuki; Nakajima, Makoto; Kobayashi, Ichizo; Toida, Masaru; Fukuda, Katsumi; Sato, Tatsuro; Nonaka, Katsumi; Gozu, Keisuke

    2007-01-01

    The authors have developed a new method of constructing high density bentonite barriers by means of a wet spraying method. Using this method, backfill material can be placed in narrow upper and side parts in a low-level radioactive waste disposal facility. Using a new supplying machine for bentonite, spraying tests were conducted to investigate the conditions during construction. On the basis of the test results, the various parameters for the spraying method were investigated. The test results are summarized as follows: 1. The new machine supplied about twice the weight of material supplied by a screw conveyor. A dry density of spraying bentonite 0.05 Mg/m 3 higher than that of a screw conveyor with the same water content could be achieved. 2. The dry density of sprayed bentonite at a boundary with concrete was the same as that at the center of the cross section. 3. The variation in densities of bentonite sprayed in the vertical downward and horizontal directions was small. Also, density reduction due to rebound during spraying was not seen. 4. Bentonite controlled by water content could be sprayed smoothly in the horizontal direction by a small machine. Also rebound could be collected by a machine conveying air. (author)

  16. Investigation of MLE in nonparametric estimation methods of reliability function

    International Nuclear Information System (INIS)

    Ahn, Kwang Won; Kim, Yoon Ik; Chung, Chang Hyun; Kim, Kil Yoo

    2001-01-01

    There have been lots of trials to estimate a reliability function. In the ESReDA 20 th seminar, a new method in nonparametric way was proposed. The major point of that paper is how to use censored data efficiently. Generally there are three kinds of approach to estimate a reliability function in nonparametric way, i.e., Reduced Sample Method, Actuarial Method and Product-Limit (PL) Method. The above three methods have some limits. So we suggest an advanced method that reflects censored information more efficiently. In many instances there will be a unique maximum likelihood estimator (MLE) of an unknown parameter, and often it may be obtained by the process of differentiation. It is well known that the three methods generally used to estimate a reliability function in nonparametric way have maximum likelihood estimators that are uniquely exist. So, MLE of the new method is derived in this study. The procedure to calculate a MLE is similar just like that of PL-estimator. The difference of the two is that in the new method, the mass (or weight) of each has an influence of the others but the mass in PL-estimator not

  17. Comparative investigation of methods for determining the lateral ...

    African Journals Online (AJOL)

    In this study, the lateral stiffness of coupled RC shear walls is studied using the continuum method, equivalent frame and finite element methods. For this purpose, asix-story coupled shear walls with typical dimensions are considered and the lateral displacements of system are calculated under a variety of lateral loads such ...

  18. Investigation on filter method for smoothing spiral phase plate

    Science.gov (United States)

    Zhang, Yuanhang; Wen, Shenglin; Luo, Zijian; Tang, Caixue; Yan, Hao; Yang, Chunlin; Liu, Mincai; Zhang, Qinghua; Wang, Jian

    2018-03-01

    Spiral phase plate (SPP) for generating vortex hollow beams has high efficiency in various applications. However, it is difficult to obtain an ideal spiral phase plate because of its continuous-varying helical phase and discontinued phase step. This paper describes the demonstration of continuous spiral phase plate using filter methods. The numerical simulations indicate that different filter method including spatial domain filter, frequency domain filter has unique impact on surface topography of SPP and optical vortex characteristics. The experimental results reveal that the spatial Gaussian filter method for smoothing SPP is suitable for Computer Controlled Optical Surfacing (CCOS) technique and obtains good optical properties.

  19. NMR methods for the investigation of structure and transport

    CERN Document Server

    Hardy, Edme H

    2011-01-01

    Methods of nuclear magnetic resonance (NMR) are increasingly applied in engineering sciences. The book summarizes research in the field of chemical and process engineering performed at the Karlsruhe Institute of Technology (KIT). Fundamentals of the methods are exposed for readers with an engineering background. Applications cover the fields of mechanical process engineering (filtration, solid-liquid separation, powder mixing, rheometry), chemical process engineering (trickle-bed reactor, ceramic sponges), bioprocess engineering (biofilm growth), and food process engineering (microwave heating

  20. Methods of amorphization and investigation of the amorphous state

    OpenAIRE

    EINFALT, TOMAŽ; PLANINŠEK, ODON; HROVAT, KLEMEN

    2013-01-01

    The amorphous form of pharmaceutical materials represents the most energetic solid state of a material. It provides advantages in terms of dissolution rate and bioavailability. This review presents the methods of solid-state amorphization described in literature (supercooling of liquids, milling, lyophilization, spray drying, dehydration of crystalline hydrates), with the emphasis on milling. Furthermore, we describe how amorphous state of pharmaceuticals differ depending on method of prepara...

  1. Investigating Diversity and Equality: Methods, Challenges and Implications

    Science.gov (United States)

    Smith, Maria

    2007-01-01

    This paper sets out the background and key findings from a number of research projects about diversity and equality at a UK university. The works were commissioned as a result of changes in legislation as well as a genuine concern to investigate the issues of inequity and institutional racism within the university. The paper explores the…

  2. resistivity methods in hydro-geophysical investigation for ...

    African Journals Online (AJOL)

    Home

    under which it occurs can be made by supplementing surface investigation with well log data which gives a clearer picture of groundwater occurrence. It is now generally accepted that the quality of water is just as important as its quantity. Quality of groundwater can be assessed based on total dissolved solids as dissolved.

  3. Investigation of electro-kinetic methods for soil decontamination

    International Nuclear Information System (INIS)

    Shabanova, A.N.

    2000-01-01

    The choices of effective methods for ecological system decontamination, their perfection and introduction into practical use have been actual tasks for the Ural region. The objective of this work has been to study the potentials of electrical kinetics method of ISOTRON Corporation (US) for decontamination of the Urals soils. Results obtained have shown the method proposed to be usable for decontaminating some types of soils from strontium and plutonium; it is low effective for decontamination in the area of South-Urals radioactive plume. Thus, a low effectiveness can be expected in podsolic and leached laterite characterized by a high content of loamy sand and sandy soils, as well as for sobby-podsolic ones. The method can be promising for decontamination of soils and wastes from chemical contaminants, such as Zn, Ni, Cu, Pb, Hg, and others. Important advantages of this method compared to others have been its simplicity, small amount of wastes, and feasibility of decontamination in areas difficult to access. (authors)

  4. Introduction to quantitative research methods an investigative approach

    CERN Document Server

    Balnaves, Mark

    2001-01-01

    Introduction to Quantitative Research Methods is a student-friendly introduction to quantitative research methods and basic statistics. It uses a detective theme throughout the text and in multimedia courseware to show how quantitative methods have been used to solve real-life problems. The book focuses on principles and techniques that are appropriate to introductory level courses in media, psychology and sociology. Examples and illustrations are drawn from historical and contemporary research in the social sciences. The multimedia courseware provides tutorial work on sampling, basic statistics, and techniques for seeking information from databases and other sources. The statistics modules can be used as either part of a detective games or directly in teaching and learning. Brief video lessons in SPSS, using real datasets, are also a feature of the CD-ROM.

  5. The Bolmen tunnel project - evaluation of geophysical site investigation methods

    International Nuclear Information System (INIS)

    Stanfors, R.

    1987-12-01

    The report presents geophysical measurements along and adjacent to the tunnel and an evaluation of the ability of the various methods to permit prediction of rock mass parameters of significance to stability and water bearing ability. The evaluation shows that, using airborne electro-magnetic surveys, it was possible to indicate about 80% of alla the zones of weakness more than 50 m wide in the tunnel. Airborne magnetic surveys located about 90% of all dolerite dykes more than 10 m wide. Ground-level VLF and Slingram methods of electro-magnetic measurement indicated 75% and 85% respectively of all zones of weakness more than 50 m wide. Resistivity methods were successfully used to locate clay filled and water-bearing fracture zones. About 75% of the length of tunnel over which resistivity values below 500 ohm m were measured required shotcrete support and pre-grouting. (orig./DG)

  6. Acoustic method for investigation of the structural defects in metals

    International Nuclear Information System (INIS)

    Nicolaescu, I.I.; Curcaneanu, Nicoleta

    1997-01-01

    In this work an acoustic method is presented called, the resonant bar method, which is based on the interaction between ultrasound and the structural defects in high purity metals. By this method the internal dislocation friction (Q -1 ) and the propagation velocity (v) of the ultrasound in the bar is measured. Both quantities are shown to depend on the dislocation densities and the length of dislocation loop. The experimental setup is shown. It consists of the resonant bar, the excitation spool, a generator of variable frequency and amplitude, a receptor spool, a selective amplifier and the adjacent measuring and displaying apparatus. The two spools are located inside of a toroidal permanent magnet. The bar oscillations are produced by the variable electromagnetic force appearing between the whirl current induced in the sample by the generator and the field of toroidal magnet. This method is applied to nonmagnetic materials with high electric conductivity. If the bar under study consists of a insulating material then on its ends either a conducting thin layer or a metallic thin sheet is deposed. The installation allows measuring the acoustic parameters of materials (v and Q -1 ) by two procedures, the method of free damped oscillations and the method of forced oscillations. Also, the internal friction can be measured with this installation, either dependent on or independent of the generator amplitude. Measurements on aluminium samples resulted in the following values: Q -1 (3 ppm) = 10 -3 and Q -1 (150 ppm) = 10 -5 . By means of this installation internal friction can be studied in re-baked, annealed, mechanical deformed and irradiated samples or in materials submitted to other processes

  7. Investigation of Optimal Integrated Circuit Raster Image Vectorization Method

    Directory of Open Access Journals (Sweden)

    Leonas Jasevičius

    2011-03-01

    Full Text Available Visual analysis of integrated circuit layer requires raster image vectorization stage to extract layer topology data to CAD tools. In this paper vectorization problems of raster IC layer images are presented. Various line extraction from raster images algorithms and their properties are discussed. Optimal raster image vectorization method was developed which allows utilization of common vectorization algorithms to achieve the best possible extracted vector data match with perfect manual vectorization results. To develop the optimal method, vectorized data quality dependence on initial raster image skeleton filter selection was assessed.Article in Lithuanian

  8. Investigation on method of elasto-plastic analysis for piping system (benchmark analysis)

    International Nuclear Information System (INIS)

    Kabaya, Takuro; Kojima, Nobuyuki; Arai, Masashi

    2015-01-01

    This paper provides method of an elasto-plastic analysis for practical seismic design of nuclear piping system. JSME started up the task to establish method of an elasto-plastic analysis for nuclear piping system. The benchmark analyses have been performed in the task to investigate on method of an elasto-plastic analysis. And our company has participated in the benchmark analyses. As a result, we have settled on the method which simulates the result of piping exciting test accurately. Therefore the recommended method of an elasto-plastic analysis is shown as follows; 1) An elasto-plastic analysis is composed of dynamic analysis of piping system modeled by using beam elements and static analysis of deformed elbow modeled by using shell elements. 2) Bi-linear is applied as an elasto-plastic property. Yield point is standardized yield point multiplied by 1.2 times, and second gradient is 1/100 young's modulus. Kinematic hardening is used as a hardening rule. 3) The fatigue life is evaluated on strain ranges obtained by elasto-plastic analysis, by using the rain flow method and the fatigue curve of previous studies. (author)

  9. Investigation of eco-friendly casein fibre production methods

    Science.gov (United States)

    Bier, M. C.; Kohn, S.; Stierand, A.; Grimmelsmann, N.; Homburg, S. V.; Rattenholl, A.; Ehrmann, A.

    2017-10-01

    The growing environmentally awareness of the consumers leads to a lot of new products in the textile industry. Either a sustainably produced textile or one which is created by reuse of a waste product is preferred. One possibility to create fibers from waste is using waste milk for casein fiber production. Opposite to several other biopolymers, however, spinning fibers from casein causes diverse problems. This article gives an overview of the investigations on how to produce fibres from the milk protein casein in a sustainable way, i.e. without formaldehyde or other polluting ingredients. Mechanical properties as well as water-resistance were investigated for chemical and physical modifications of the base composition. In this way, the positive influence of paraffin oil and wax as well as aggregation at high temperatures could be proven, while temperature treatment resulted in a higher E-modulus.

  10. Investigation of Aerodynamic Interference in a Multirotor by PIV Method

    Directory of Open Access Journals (Sweden)

    Zbigniew Czyż

    2018-03-01

    Full Text Available This paper presents part of the investigation into aerodynamics of the vertical take-off and landing multirotor. There are described the technology to design a research object and the Particle Image Velocimetry (PIV setup to measure airflow around the aircraft. The around-the-aircraft speed distribution was investigated for an angle of attack of 0o and for four different configurations. The results are presented in form of vector velocity field of airflow on the plane of symmetry of the test object. The results enabled the characteristics of speed vs. the distance from the fuselage. It was observed that the push propeller and the main rotor impact the speed field around the fuselage.

  11. Fracture toughness of fabrication welds investigated by metallographic methods

    International Nuclear Information System (INIS)

    Canonico, D.A.; Crouse, R.S.

    1978-01-01

    The intermediate scale test vessels (ITV) were fabricated to provide test specimens that have sufficient wall thickness and simulate light water reactor pressure vessels. They were fabricated from grades of steel that are similar to those used for nuclear pressure vessels, having a wall thickness of 150mm and the same welded construction. They are, however, considerably smaller in height and diameter than actual vessels. To date, ten vessels have been fabricated and eight have been tested. In preparation for testing the eighth vessel (ITV-8), an extensive investigation was conducted of the toughness properties of the fabrication weld. It was thoroughly characterized and the fracture specimens used in this metallographic investigation were taken from that weld metal

  12. Investigation of the clinical features and therapeutic methods for the ...

    African Journals Online (AJOL)

    Purpose: To establish if there are different classes of inflammatory lacrimal punctum diseases (ILPDs) and to examine the various strategies by which they can be managed therapeutically. Methods: Two hundred and fifty nine (259) patients with inflammatory punctum lacrimal disease were identified and used as subjects for ...

  13. Investigation of Chemical Equilibrium Kinetics by the Electromigration Method

    CERN Document Server

    Bozhikov, G A; Bontchev, G D; Maslov, O D; Milanov, M V; Dmitriev, S N

    2002-01-01

    Measurement of the chemical reaction rates for complex formation as well as hydrolysis type reactions by the method of horizontal zone electrophoresis is outlined. The correlation between chemical equilibrium kinetics and electrodiffusion processes in a constant d.c. electric field is described. In model electromigration experiments the reaction rate constant of the complex formation of Hf(IV) and DTPA is determined.

  14. Investigating salt frost scaling by using statistical methods

    DEFF Research Database (Denmark)

    Hasholt, Marianne Tange; Clemmensen, Line Katrine Harder

    2010-01-01

    A large data set comprising data for 118 concrete mixes on mix design, air void structure, and the outcome of freeze/thaw testing according to SS 13 72 44 has been analysed by use of statistical methods. The results show that with regard to mix composition, the most important parameter...

  15. Investigation on Carbohydrate Counting Method in Type 1 Diabetic Patients

    Directory of Open Access Journals (Sweden)

    Osman Son

    2014-01-01

    Full Text Available Objective. The results from Diabetes Control and Complications Trial (DCCT have propounded the importance of the approach of treatment by medical nutrition when treating diabetes mellitus (DM. During this study, we tried to inquire carbohydrate (Kh count method’s positive effects on the type 1 DM treatment’s success as well as on the life quality of the patients. Methods. 22 of 37 type 1 DM patients who applied to Eskişehir Osmangazi University, Faculty of Medicine Hospital, Department of Endocrinology and Metabolism, had been treated by Kh count method and 15 of them are treated by multiple dosage intensive insulin treatment with applying standard diabetic diet as a control group and both of groups were under close follow-up for 6 months. Required approval was taken from the Ethical Committee of Eskişehir Osmangazi University, Medical Faculty, as well as informed consent from the patients. The body weight of patients who are treated by carbohydrate count method and multiple dosage intensive insulin treatment during the study beginning and after 6-month term, body mass index, and body compositions are analyzed. A short life quality and medical research survey applied. At statistical analysis, t-test, chi-squared test, and Mann-Whitney U test were used. Results. There had been no significant change determined at glycemic control indicators between the Kh counting group and the standard diabetic diet and multiple dosage insulin treatment group in our study. Conclusion. As a result, Kh counting method which offers a flexible nutrition plan to diabetic individuals is a functional method.

  16. Geophysical Methods for Investigating Ground-Water Recharge

    Science.gov (United States)

    Ferre, Ty P.A.; Binley, Andrew M.; Blasch, Kyle W.; Callegary, James B.; Crawford, Steven M.; Fink, James B.; Flint, Alan L.; Flint, Lorraine E.; Hoffmann, John P.; Izbicki, John A.; Levitt, Marc T.; Pool, Donald R.; Scanlon, Bridget R.

    2007-01-01

    While numerical modeling has revolutionized our understanding of basin-scale hydrologic processes, such models rely almost exclusively on traditional measurements?rainfall, streamflow, and water-table elevations?for calibration and testing. Model calibration provides initial estimates of ground-water recharge. Calibrated models are important yet crude tools for addressing questions about the spatial and temporal distribution of recharge. An inverse approach to recharge estimation is taken of necessity, due to inherent difficulties in making direct measurements of flow across the water table. Difficulties arise because recharging fluxes are typically small, even in humid regions, and because the location of the water table changes with time. Deep water tables in arid and semiarid regions make recharge monitoring especially difficult. Nevertheless, recharge monitoring must advance in order to improve assessments of ground-water recharge. Improved characterization of basin-scale recharge is critical for informed water-resources management. Difficulties in directly measuring recharge have prompted many efforts to develop indirect methods. The mass-balance approach of estimating recharge as the residual of generally much larger terms has persisted despite the use of increasing complex and finely gridded large-scale hydrologic models. Geophysical data pertaining to recharge rates, timing, and patterns have the potential to substantially improve modeling efforts by providing information on boundary conditions, by constraining model inputs, by testing simplifying assumptions, and by identifying the spatial and temporal resolutions needed to predict recharge to a specified tolerance in space and in time. Moreover, under certain conditions, geophysical measurements can yield direct estimates of recharge rates or changes in water storage, largely eliminating the need for indirect measures of recharge. This appendix presents an overview of physically based, geophysical methods

  17. NMR methods for the investigation of structure and transport

    Energy Technology Data Exchange (ETDEWEB)

    Hardy, Edme H. [Karlsruher Institut fuer Technologie (KIT), Karlsruhe (Germany). Inst. fuer Mechanische Verfahrenstechnik und Mechanik

    2012-07-01

    Extensive derivations of required fundamental relations for readers with engineering background New applications based on MRI, PGSE-NMR, and low-field NMR New concepts in quantitative data evaluation and image analysis Methods of nuclear magnetic resonance (NMR) are increasingly applied in engineering sciences. The book summarizes research in the field of chemical and process engineering performed at the Karlsruhe Institute of Technology (KIT). Fundamentals of the methods are exposed for readers with an engineering background. Applications cover the fields of mechanical process engineering (filtration, solid-liquid separation, powder mixing, rheometry), chemical process engineering (trickle-bed reactor, ceramic sponges), bioprocess engineering (biofilm growth), and food process engineering (microwave heating, emulsions). Magnetic Resonance Imaging (MRI) as well as low-field NMR are covered with notes on hardware. Emphasis is placed on quantitative data analysis and image processing. (orig.)

  18. NMR methods for the investigation of structure and transport

    International Nuclear Information System (INIS)

    Hardy, Edme H.

    2012-01-01

    Extensive derivations of required fundamental relations for readers with engineering background New applications based on MRI, PGSE-NMR, and low-field NMR New concepts in quantitative data evaluation and image analysis Methods of nuclear magnetic resonance (NMR) are increasingly applied in engineering sciences. The book summarizes research in the field of chemical and process engineering performed at the Karlsruhe Institute of Technology (KIT). Fundamentals of the methods are exposed for readers with an engineering background. Applications cover the fields of mechanical process engineering (filtration, solid-liquid separation, powder mixing, rheometry), chemical process engineering (trickle-bed reactor, ceramic sponges), bioprocess engineering (biofilm growth), and food process engineering (microwave heating, emulsions). Magnetic Resonance Imaging (MRI) as well as low-field NMR are covered with notes on hardware. Emphasis is placed on quantitative data analysis and image processing. (orig.)

  19. Low resolution spectroscopic investigation of Am stars using Automated method

    Science.gov (United States)

    Sharma, Kaushal; Joshi, Santosh; Singh, Harinder P.

    2018-04-01

    The automated method of full spectrum fitting gives reliable estimates of stellar atmospheric parameters (Teff, log g and [Fe/H]) for late A, F, G, and early K type stars. Recently, the technique was further improved in the cooler regime and the validity range was extended up to a spectral type of M6 - M7 (Teff˜ 2900 K). The present study aims to explore the application of this method on the low-resolution spectra of Am stars, a class of chemically peculiar stars, to examine its robustness for these objects. We use ULySS with the Medium-resolution INT Library of Empirical Spectra (MILES) V2 spectral interpolator for parameter determination. The determined Teff and log g values are found to be in good agreement with those obtained from high-resolution spectroscopy.

  20. Investigation of the radioactivity of rocks by the photographic method

    Energy Technology Data Exchange (ETDEWEB)

    Poole, J H.J.; Bremner, J W

    1948-06-05

    The method employed is to place an Ilford Nuclear Research plate at a distance of about 0.1 mm from a flat surface of the specimen cut with a diamond saw, and expose it for one to three weeks, depending or the probable activity of the specimen. In more recent experiments the plate has been placed in contact with the cut surface, as this makes easier the identification of ..cap alpha..-rays tracks, which all originate from one nucleus. Theoretically, from the frequencies of two-, three-, four-, and five-ray stars, it should be possible to estimate the separate amounts of uranium and thorium present. Enough data have not yet been obtained to determine whether this method will prove possible. The results of some experiments are reviewed briefly.

  1. Investigation of Oxidation Methods for Waste Soy Sauce Treatment

    Directory of Open Access Journals (Sweden)

    Hyun-Hee Jang

    2017-10-01

    Full Text Available To obtain a suitable oxidation method for removing the color and lowering the chemical oxygen demand (COD of waste soy sauce, Fenton (Fe2+, Fenton-like (Fe3+, and ozone (O3 oxidation methods are used as the target reactions. In experimental conditions for Fenton oxidation, the dose of Fe2+ and Fe3+ was varied between 100 mg/L and 300 mg/L. The dose of hydrogen peroxide for the reaction was injected from 100–1000 mg/L. For ozone oxidation, the pH was increased from 3 to 14 and the O3-containing gas was supplied continuously for 30 min through a gas diffuser at the bottom of the reactor at different applied O3 doses (10–90 mg/L. We subjected it to a simple 1:20 dilution with deionized water to identify the comparison result in detail. O3 oxidation shows the highest efficiencies of color removal (81.1% and COD lowering (64.9% among the three oxidation methods. This is mainly due to the fact that it has a relatively large amount of hydroxyl radical, resulting in the degradation of organics. Thus, O3 oxidation could be a promising method for removing the color and lowering the COD of waste soy sauce. The critical parameters (pH and applied O3 dose were varied systematically to optimize O3 oxidation. It was found that the optimum pH and applied O3 dose are 11.0 mg/L and 50.0 mg/L, respectively (color removal = 34.2%, COD removal = 27.4%.

  2. Investigation of Oxidation Methods for Waste Soy Sauce Treatment.

    Science.gov (United States)

    Jang, Hyun-Hee; Seo, Gyu-Tae; Jeong, Dae-Woon

    2017-10-07

    To obtain a suitable oxidation method for removing the color and lowering the chemical oxygen demand (COD) of waste soy sauce, Fenton (Fe 2+ ), Fenton-like (Fe 3+ ), and ozone (O₃) oxidation methods are used as the target reactions. In experimental conditions for Fenton oxidation, the dose of Fe 2+ and Fe 3+ was varied between 100 mg/L and 300 mg/L. The dose of hydrogen peroxide for the reaction was injected from 100-1000 mg/L. For ozone oxidation, the pH was increased from 3 to 14 and the O₃-containing gas was supplied continuously for 30 min through a gas diffuser at the bottom of the reactor at different applied O₃ doses (10-90 mg/L). We subjected it to a simple 1:20 dilution with deionized water to identify the comparison result in detail. O 3 oxidation shows the highest efficiencies of color removal (81.1%) and COD lowering (64.9%) among the three oxidation methods. This is mainly due to the fact that it has a relatively large amount of hydroxyl radical, resulting in the degradation of organics. Thus, O₃ oxidation could be a promising method for removing the color and lowering the COD of waste soy sauce. The critical parameters (pH and applied O₃ dose) were varied systematically to optimize O₃ oxidation. It was found that the optimum pH and applied O₃ dose are 11.0 mg/L and 50.0 mg/L, respectively (color removal = 34.2%, COD removal = 27.4%).

  3. An Investigation into the Methods of Teaching Creative English Writing

    Directory of Open Access Journals (Sweden)

    Anastasiia Riabokrys

    2016-08-01

    Full Text Available The article is devoted to the actual problem of teaching creative writing at the English lessons. The value of writing in the process of teaching English language is revealed. The principles and peculiarities of evaluation of creative writing are analyzed. The strategy of choosing methods in teaching creative writing is identified. The benefits of creative writing for learner and teachers are considered.

  4. Investigation of free radicals in paprika with the ESR method

    International Nuclear Information System (INIS)

    Kispeter, J.; Szabo, I.; Horvath, L.J.

    1998-01-01

    Complete text of publication follows. The ESR method is the one of the most successfully applied method among the physical methods for the identification of radiation or ionising treatment of foods. The identification of free radicals having short and long lifetimes is the base of the measurement. The quantitative determination makes possible the determination of the absorbed dose deriving from 60 Co radiation treatment. It has to be noted that the treatment of the foods with ionising radiation and other treatments (milling, frying, baking) and the oxidative process result free radicals in paprika samples as a function of absorbed radiation dose (2.5; 5 and 10 kGy) on the different particle size and on storage time. The intensities of the samples given after each of the seven stages of the paprika milling increased till the fifth stage corresponding to the effect of a 2 kGy absorbed dose. After conditioning and increasing the water content by 5-8% the ESR intensity shows significant lowering. This value characterises the ESR intensity of not irradiated sample. As an effect of the irradiation the ESR intensities increased along with the increase of the absorbed dose. The samples having lower particle size are more sensible for the identification of the irradiation. Evaluating the art of the decline we concluded that there are free radicals having short and long shelf lifetimes in paprika samples at the same time

  5. X-ray topographic method of investigation of phase objects

    International Nuclear Information System (INIS)

    Levonyan, L.V.

    2001-01-01

    The intensity distribution of the monochromatized synchrotron radiation transmitting through the phase object and crystal-analyzer in Laue geometry is considered. It is shown that the local angular deviation of the incident radiation caused by the refraction on structural inhomogeneities of the object under investigation is directly transferred to the X-ray topographic image. In the absence of the phase object the latter consists of parallel straight fringes with a slowly decreasing period. The presence of the phase object changes the shape and period of fringes. The influence of the spatial and temporal coherence on the image is discussed. 5 refs

  6. Using Experimental Methods to Investigate Discriminatory Tendencies: A Lesson Report

    Directory of Open Access Journals (Sweden)

    Yu-Wen Chen

    2013-08-01

    Full Text Available Using dictator games in experimental analysis, this lesson report demonstrates the process and results of a postgraduate class project in which university students were instructed to scientifically investigate and explore one of German society’s most hotly-contested issues: the level of discriminatory tendencies of non-Muslims towards Muslims. The results of this class project show little or no discriminatory tendencies toward Muslims. Instead, the university students under our investigation tended to act favorably, or at the very least, fairly toward Muslims. We expect that this lesson report can demonstrate how a postgraduate course can be conducted in an innovative way, empowering students to collect primary data and finishing a small scientific project during the span of a semester. Dieser Bericht stellt die Prozesse und Ergebnisse einer experimentellen Studie eines Postgraduierten-Kurses der Universität Greifswald dar. Wir zeigen, wie Studierende das Thema Migration innovativ untersuchen können, indem sie neben theoretischen Lerninhalten an experimentelle Methoden sowie die Primärforschung herangeführt werden. Anhand eines Diktatorspiels wurden die teilnehmenden Studenten angeleitet, ein in der Öffentlichkeit kontrovers debattiertes Thema wissenschaftlich zu untersuchen: Diskriminierende Tendenzen von Nicht-Muslimen gegenüber Muslimen. Die Ergebnisse dieser Studie lassen jedoch nicht auf diskriminierende Tendenzen der Studenten schließen. Stattdessen deuten sie darauf hin, dass sich die Studierenden zumindest fair gegenüber Muslimen verhalten.

  7. Laserspritzer: a simple method for optogenetic investigation with subcellular resolutions.

    Directory of Open Access Journals (Sweden)

    Qian-Quan Sun

    Full Text Available To build a detailed circuit diagram in the brain, one needs to measure functional synaptic connections between specific types of neurons. A high-resolution circuit diagram should provide detailed information at subcellular levels such as soma, distal and basal dendrites. However, a limitation lies in the difficulty of studying long-range connections between brain areas separated by millimeters. Brain slice preparations have been widely used to help understand circuit wiring within specific brain regions. The challenge exists because long-range connections are likely to be cut in a brain slice. The optogenetic approach overcomes these limitations, as channelrhodopsin 2 (ChR2 is efficiently transported to axon terminals that can be stimulated in brain slices. Here, we developed a novel fiber optic based simple method of optogenetic stimulation: the laserspritzer approach. This method facilitates the study of both long-range and local circuits within brain slice preparations. This is a convenient and low cost approach that can be easily integrated with a slice electrophysiology setup, and repeatedly used upon initial validation. Our data with direct ChR2 mediated-current recordings demonstrates that the spatial resolution of the laserspritzer is correlated with the size of the laserspritzer, and the resolution lies within the 30 µm range for the 5 micrometer laserspritzer. Using olfactory cortical slices, we demonstrated that the laserspritzer approach can be applied to selectively activate monosynaptic perisomatic GABAergic basket synapses, or long-range intracortical glutamatergic inputs formed on different subcellular domains within the same cell (e.g. distal and proximal dendrites. We discuss significant advantages of the laserspritzer approach over the widely used collimated LED whole-field illumination method in brain slice electrophysiological research.

  8. High-Throughput Sequencing Based Methods of RNA Structure Investigation

    DEFF Research Database (Denmark)

    Kielpinski, Lukasz Jan

    In this thesis we describe the development of four related methods for RNA structure probing that utilize massive parallel sequencing. Using them, we were able to gather structural data for multiple, long molecules simultaneously. First, we have established an easy to follow experimental...... and computational protocol for detecting the reverse transcription termination sites (RTTS-Seq). This protocol was subsequently applied to hydroxyl radical footprinting of three dimensional RNA structures to give a probing signal that correlates well with the RNA backbone solvent accessibility. Moreover, we applied...

  9. Investigation of reaction equilibrium in reactor materials by EMF methods

    International Nuclear Information System (INIS)

    Ullmann, H.; Teske, K.; Reetz, T.; Rettig, D.; Kozlov, F.A.; Kuznecov, E.K.

    1979-01-01

    By means of electrochemical cells with solid electrolytes measurements of the chemical activities of oxygen and hydrogen in a sodium test loop were performed. The reaction equilibrium of oxygen and hydrogen in dilute solutions of sodium was investigated. The activities of both oxygen and hydrogen decrease with increasing concentration of the reaction partner. From the relation between the activivy of one component and the analytic concentration of the reaction partner the equilibrium constant of the reaction 0+H = OH was determinded to lg K sub(diss) = -(1,502+-0,216)-(1356+-140)/T. An electrochemical cell with an iron membrane and a solid electrolyte was used to measure the activity of carbon in a carborizing medium. The cell output was stable over a period of more than 1000 hours at a carbon activity of 1. (orig.) [de

  10. Comparison of two methods for investigating indoor radon daughters

    International Nuclear Information System (INIS)

    Vanmarcke, H.; Raes, F.

    1988-01-01

    The dynamics of radon daughters in realistic indoor environments has been investigated experimentally at the Universities of Gottingen and Gent. Both studies yielded the important result that the fraction of unattached radon daughters is higher than is assumed in earlier studies. Reineking-Porstendorfer and Vanmarcke-Raes adopted quite different methodologies to determine the unattached fraction. In this paper the methodologies are compared by means of joint measurements performed in a house with elevated radon concentrations. The results for the attachment rate, the deposition rate of the unattached daughters and the unattached fraction differ significantly, while the results for the deposition rate of the attached daughters and the equilibrium factor broadly agree. (author)

  11. A method for investigating relative timing information on phylogenetic trees.

    Science.gov (United States)

    Ford, Daniel; Matsen, Frederick A; Stadler, Tanja

    2009-04-01

    In this paper, we present a new way to describe the timing of branching events in phylogenetic trees. Our description is in terms of the relative timing of diversification events between sister clades; as such it is complementary to existing methods using lineages-through-time plots which consider diversification in aggregate. The method can be applied to look for evidence of diversification happening in lineage-specific "bursts", or the opposite, where diversification between 2 clades happens in an unusually regular fashion. In order to be able to distinguish interesting events from stochasticity, we discuss 2 classes of neutral models on trees with relative timing information and develop a statistical framework for testing these models. These model classes include both the coalescent with ancestral population size variation and global rate speciation-extinction models. We end the paper with 2 example applications: first, we show that the evolution of the hepatitis C virus deviates from the coalescent with arbitrary population size. Second, we analyze a large tree of ants, demonstrating that a period of elevated diversification rates does not appear to have occurred in a bursting manner.

  12. Multi-offset GPR methods for hyporheic zone investigations

    Science.gov (United States)

    Brosten, T.R.; Bradford, J.H.; McNamara, J.P.; Gooseff, M.N.; Zarnetske, J.P.; Bowden, W.B.; Johnston, M.E.

    2009-01-01

    Porosity of stream sediments has a direct effect on hyporheic exchange patterns and rates. Improved estimates of porosity heterogeneity will yield enhanced simulation of hyporheic exchange processes. Ground-penetrating radar (GPR) velocity measurements are strongly controlled by water content thus accurate measures of GPR velocity in saturated sediments provides estimates of porosity beneath stream channels using petrophysical relationships. Imaging the substream system using surface based reflection measurements is particularly challenging due to large velocity gradients that occur at the transition from open water to saturated sediments. The continuous multi-offset method improves the quality of subsurface images through stacking and provides measurements of vertical and lateral velocity distributions. We applied the continuous multi-offset method to stream sites on the North Slope, Alaska and the Sawtooth Mountains near Boise, Idaho, USA. From the continuous multi-offset data, we measure velocity using reflection tomography then estimate water content and porosity using the Topp equation. These values provide detailed measurements for improved stream channel hydraulic and thermal modelling. ?? 2009 European Association of Geoscientists & Engineers.

  13. Investigation of medieval ceramics from Ras by physicochemical methods

    Directory of Open Access Journals (Sweden)

    Zindović Nataša D.

    2008-01-01

    Full Text Available Although early medieval Serbian ceramic is well described by the archeologists and historians, knowledge of the Balkan ceramic production is still limited. Archaeometric study of ceramics provenance, technology of preparation and used pigments as well as influence of neighboring countries and specific characteristics of different workshops has never been performed so far. The detailed knowledge of the micro-chemical and micro-structural nature of an archaeological artifact is critical in finding solutions to problems of restoration, conservation, dating and authentication in the art world. In this work we present results of systematic investigation of pottery shards from archeological site Ras. The term Ras, which signifies both the fortress and the region encompassing the upper course of Raška River, used to be the center of the medieval Serbian state. Both the ceramic body and the polychromatic glaze of the artifacts were studied by a multianalitical approach combining optical microscopy (OM, FT-IR spectroscopy and X-ray fluorescence (XRF. Mineralogical composition of pottery shards has been determined combining results obtained by FT-IR spectroscopy, after deconvolution of the spectra, and XRPD analysis. Firing temperature has been estimated based on the mineralogical composition and positions of Si-O stretching (-1000 cm-1 and banding (-460 cm-1 vibrations. Investigated samples have been classified into two groups based on the mineralogical composition, cross sections and firing temperature. Larger group consists of samples of fine-grained, homogeneous ceramics with firing temperatures bellow 800 °C which indicates imported products. Second, smaller group consists of inhomogeneous ceramics with firing temperatures between 850 and 900 °C produced in the domestic workshops. The obtained results will be used to build up a national database for the compositions of bodies, glazes and pigments.

  14. Investigating low-frequency compression using the Grid method

    DEFF Research Database (Denmark)

    Fereczkowski, Michal; Dau, Torsten; MacDonald, Ewen

    2016-01-01

    in literature. Moreover, slopes of the low-level portions of the BM I/O functions estimated at 500 Hz were examined, to determine whether the 500-Hz off-frequency forward masking curves were affected by compression. Overall, the collected data showed a trend confirming the compressive behaviour. However......There is an ongoing discussion about whether the amount of cochlear compression in humans at low frequencies (below 1 kHz) is as high as that at higher frequencies. It is controversial whether the compression affects the slope of the off-frequency forward masking curves at those frequencies. Here......, the Grid method with a 2-interval 1-up 3-down tracking rule was applied to estimate forward masking curves at two characteristic frequencies: 500 Hz and 4000 Hz. The resulting curves and the corresponding basilar membrane input-output (BM I/O) functions were found to be comparable to those reported...

  15. Investigation of defects on PAMS microspheres fabricated with microencapsulation method

    International Nuclear Information System (INIS)

    Chen Sufen; Li Bo; Liu Yiyang; Zhang Zhanwen; Qi Xiaobo

    2012-01-01

    Poly-(α-methylstyrene) (PAMS) microspheres were fabricated with W1/O/W2 double emulsion microencapsulation method, and the effects of polyvinylalcohol (PVA) and CaCl 2 weight concentrations and the O/W2 phase ratio on the percentages of defected PAMS microspheres were studied. The weight concentrations of PVA and CaCl 2 and the O/W2 phase ratio in the fabrication process of PAMS microspheres were optimized. The results show that, for the three parameters being 1.0%, 1.5%, and 0.01, respectively, the percentage of the defect-free PAMS microspheres without vacuoles in the shell wall can be up to 60%. (authors)

  16. Application of mathematical methods to the investigation of uranium deposits

    International Nuclear Information System (INIS)

    Formery, P.; Ziegler, V.

    1958-01-01

    It may be considered approximately that grades, widths and accumulations (grade-width products), in french uranium deposits are distributed according to a lognormal law. This property associated to KRIGE'S and de WIGE'S formulae make a powerful tool in ore deposits surveys. The correlation between radioactivities and grades is realized, in logarithmic coordinates, through a straight line the properties of which are analysed in the paper. MATHERON'S recent works, in association with data of classical statistics and the above mentioned formulae make possible to complete the ore reserves evaluation by computing the accuracy. Statistical methods applied to ore deposits have given birth to a parameter which is as important as the mean grade for characterisation of deposits: the absolute dispersion. (author) [fr

  17. Investigation of chemical equilibrium kinetics by the electromigration method

    International Nuclear Information System (INIS)

    Bozhikov, G.A.; Ivanov, P.I.; Maslov, O.D.; Dmitriev, S.N.; Bontchev, G.D.; Milanov, M.V.

    2003-01-01

    The measurement of the chemical reaction rates for complex formation as well as hydrolysis type reactions by the method of horizontal zone electrophoresis is outlined. The correlation between chemical equilibrium kinetics and electrodiffusion processes in a constant d.c. electric field is described. In model electromigration experiments the reaction rate constant of the formation a complex by Hf(IV) and diethylenetriaminepentaacetic acid (DTPA) is determined. The electrophoretic mobility, diffusion coefficient and stability constant of the [HfDTPA] - complex are calculated, taking into account experimental electrophoretic data obtained at 298.15±0.05 K and constant ionic strength. No-carrier-added 175 Hf radionuclide was used in electromigration experiments at concentrations of 10 -10 -10 -11 M. (orig.)

  18. Operational auditing versus traditional method: A comparative investigation

    Directory of Open Access Journals (Sweden)

    Reza Tehrani

    2013-06-01

    Full Text Available Operational auditing is one of the management consultancy services whose significance is on the rise day by day. This approach is, clearly, a systematic and methodical process used to evaluate economic savings of financial processes in organizations and the results of the evaluations are reported to interested people along with some comments to improve operational processes. Accordingly, it appears that the proper employment of the existing rationale in operational auditing can be a significant step towards the improvement of financial efficiency in Iranian public and private banking sector. This paper studies the effects of operational auditing on the improvement of economic saving of financial processes in Iranian private banks compared with traditional approaches where the operations are based on financial statements. The population of this survey includes 15 private and public Iranian banks and the proposed study selects 78 branches, randomly. The Cronbach alpha was used to test the reliability a questionnaire employed to collect the needed data in this study. The results obtained by SPSS Software indicated that the reliability of the instrumentsanged between 0.752 and 0.867, suggesting an acceptable level of the reliability for the questionnaire. Besides, content validity was used to confirm the validity of the instrument. The results of the study indicated that the operational auditing as a useful approach influencing the financial efficiency of public and private banks has significantly transformed the traditional thinking in the field of management auditing. The operational auditing has a number of significant advantages including a better method of controlling financial operations within Iranian banks, efficient planning in the future, facilitating efficient, appropriate, and accurate management decision making, and sound evaluation of managers’ financial operations.

  19. Investigating Methods for Serving Visualizations of Vertical Profiles

    Science.gov (United States)

    Roberts, J. T.; Cechini, M. F.; Lanjewar, K.; Rodriguez, J.; Boller, R. A.; Baynes, K.

    2017-12-01

    Several geospatial web servers, web service standards, and mapping clients exist for the visualization of two-dimensional raster and vector-based Earth science data products. However, data products with a vertical component (i.e., vertical profiles) do not have the same mature set of technologies and pose a greater technical challenge when it comes to visualizations. There are a variety of tools and proposed standards, but no obvious solution that can handle the variety of visualizations found with vertical profiles. An effort is being led by members of the NASA Global Imagery Browse Services (GIBS) team to gather a list of technologies relevant to existing vertical profile data products and user stories. The goal is to find a subset of technologies, standards, and tools that can be used to build publicly accessible web services that can handle the greatest number of use cases for the widest audience possible. This presentation will describe results of the investigation and offer directions for moving forward with building a system that is capable of effectively and efficiently serving visualizations of vertical profiles.

  20. Sharing information: Mixed-methods investigation of brief experiential interprofessional

    Science.gov (United States)

    Cocksedge, Simon; Barr, Nicky; Deakin, Corinne

    In UK health policy ‘sharing good information is pivotal to improving care quality, safety, and effectiveness. Nevertheless, educators often neglect this vital communication skill. The consequences of brief communication education interventions for healthcare workers are not yet established. This study investigated a three-hour interprofessional experiential workshop (group work, theoretical input, rehearsal) training healthcare staff in sharing information using a clear structure (PARSLEY). Staff in one UK hospital participated. Questionnaires were completed before, immediately after, and eight weeks after training, with semistructured interviews seven weeks after training. Participants (n=76) were from assorted healthcare occupations (26% non-clinical). Knowledge significantly increased immediately after training. Self-efficacy, outcome expectancy, and motivation to use the structure taught were significantly increased immediately following training and at eight weeks. Respondents at eight weeks (n=35) reported their practice in sharing information had changed within seven days of training. Seven weeks after training, most interviewees (n=13) reported confidently using the PARSLEY structure regularly in varied settings. All had re-evaluated their communication practice. Brief training altered self-reported communication behaviour of healthcare staff, with sustained changes in everyday work. As sharing information is central to communication curricula, health policy, and shared decision-making, the effectiveness of brief teaching interventions has economic and educational implications.

  1. Creative Design Methods and Investigation of Cellulose Fiber Transport and Application

    National Research Council Canada - National Science Library

    Spencer, Mack-Jan

    1999-01-01

    .... Correlations between the four design methods were also discovered. These investigated methods were analogical reasoning, brainstorming, synectics, and the theory of inventive problem solving (TIPS...

  2. New experimental method for investigation of the nucleon polarizabilities

    International Nuclear Information System (INIS)

    Yevetska, O.; Watzlawik, S.; Ahrens, J.; Alkhazov, G.D.; Chizhov, V.P.; Maev, E.M.; Neumann-Cosel, P. von; Orischin, E.M.; Petrov, G.E.; Porte, J.-M.; Richter, A.; Sarantsev, V.V.; Schrieder, G.; Smirenin, Yu.V.

    2010-01-01

    At the continuous wave (cw) Superconducting Darmstadt Electron Linear Accelerator S-DALINAC, a new method has been developed for the determination of the electric (α-bar) and magnetic (β-bar) polarizabilities of the proton and the deuteron. For that purpose the energy and angular dependence of the differential cross-section for elastic γp and γd scattering of bremsstrahlung photons in the energy range between 20 and 100 MeV is measured by detecting the recoiling proton (deuteron) in coincidence with the scattered bremsstrahlung photon. α-bar and β-bar are then found by means of a best fit to a theoretical description of the scattering cross-section with these quantities as open parameters. The experimental setup consists of a bremsstrahlung photon facility, two specially designed high pressure hydrogen (deuterium) ionization chambers which serve as targets and detectors of the recoil proton (deuteron), NaI gamma spectrometers and several additional detectors for beam diagnostics and normalization. The whole setup was tested using bremsstrahlung photon beams with endpoint energies of 60 and 79.3 MeV. The results of the test experiments show that future high-statistics measurements are feasible.

  3. Previously unknown species of Aspergillus.

    Science.gov (United States)

    Gautier, M; Normand, A-C; Ranque, S

    2016-08-01

    The use of multi-locus DNA sequence analysis has led to the description of previously unknown 'cryptic' Aspergillus species, whereas classical morphology-based identification of Aspergillus remains limited to the section or species-complex level. The current literature highlights two main features concerning these 'cryptic' Aspergillus species. First, the prevalence of such species in clinical samples is relatively high compared with emergent filamentous fungal taxa such as Mucorales, Scedosporium or Fusarium. Second, it is clearly important to identify these species in the clinical laboratory because of the high frequency of antifungal drug-resistant isolates of such Aspergillus species. Matrix-assisted laser desorption/ionization-time of flight mass spectrometry (MALDI-TOF MS) has recently been shown to enable the identification of filamentous fungi with an accuracy similar to that of DNA sequence-based methods. As MALDI-TOF MS is well suited to the routine clinical laboratory workflow, it facilitates the identification of these 'cryptic' Aspergillus species at the routine mycology bench. The rapid establishment of enhanced filamentous fungi identification facilities will lead to a better understanding of the epidemiology and clinical importance of these emerging Aspergillus species. Based on routine MALDI-TOF MS-based identification results, we provide original insights into the key interpretation issues of a positive Aspergillus culture from a clinical sample. Which ubiquitous species that are frequently isolated from air samples are rarely involved in human invasive disease? Can both the species and the type of biological sample indicate Aspergillus carriage, colonization or infection in a patient? Highly accurate routine filamentous fungi identification is central to enhance the understanding of these previously unknown Aspergillus species, with a vital impact on further improved patient care. Copyright © 2016 European Society of Clinical Microbiology and

  4. Mixed Methods Research in School Psychology: A Mixed Methods Investigation of Trends in the Literature

    Science.gov (United States)

    Powell, Heather; Mihalas, Stephanie; Onwuegbuzie, Anthony J.; Suldo, Shannon; Daley, Christine E.

    2008-01-01

    This article illustrates the utility of mixed methods research (i.e., combining quantitative and qualitative techniques) to the field of school psychology. First, the use of mixed methods approaches in school psychology practice is discussed. Second, the mixed methods research process is described in terms of school psychology research. Third, the…

  5. Carer mentoring: a mixed methods investigation of a carer mentoring service.

    Science.gov (United States)

    Greenwood, Nan; Habibi, Ruth

    2014-03-01

    Worldwide with ageing populations, the numbers of informal carers are likely to increase. Although being a carer is often satisfying, it can be challenging and require support. Volunteer-provided carer mentoring services where carers are supported by volunteer mentors are one such intervention. However, little is known about the impact of mentoring, carers' experiences or the mechanisms by which these schemes may work. Previous quantitative findings have been inconsistent suggesting a different, mixed methods approach using qualitative and quantitative methods may be valuable. Objectives were to explore two main questions: whether mentoring had a significant positive effect on carer mentees in terms of mental health, quality of life and confidence in caring and to explore how carers experience and perceive the process and benefits of mentoring. In addition, the study aimed to suggest possible mechanisms to understand how mentoring may benefit carers. Mixed methods (quantitative questionnaires and depth interviews) investigated an established mentoring service provided by volunteer mentors. During the study period, 28 carers received mentoring. Of these, 25 carers completed structured questionnaires both before and after mentoring, to determine whether mentoring had an impact on carer wellbeing and confidence in caring. Depth interviews were also undertaken with 11 purposively sampled carers to explore how carers experience and perceive the process and benefits of mentoring. Statistically significant improvements in carer anxiety (pemotional support, information provision, problem solving facilitation and gaining new perspectives may be mechanisms by which mentoring achieves positive outcomes. Mentor personal characteristics, experiences and training are possible facilitators of the process. Carer mentoring services can be a valuable form of carer support that falls somewhere between formal and informal support. Adopting mixed methods permitted greater understanding

  6. Validation of the method for investigation of radiopharmaceuticals for in vitro use

    International Nuclear Information System (INIS)

    Vranjes, S; Jovanovic, M.; Orlic, M.; Lazic, E. . E-mail address of corresponding author: sanjav@vin.bg.ac.yu

    2005-01-01

    The aim of this study was to validate analytical method for determination of total radioactivity and radioactive concentration of 125 I-triiodotironin, radiopharmaceutical for in vitro use. Analytical parameters: selectivity, accuracy, linearity and range of this method were determined. Values obtained for all parameters are reasonable for analytical methods, therefore this method could be used for farther investigation. (author)

  7. Pedagogical Practices and Counselor Self-Efficacy: A Mixed Methods Investigations

    Science.gov (United States)

    Brogan, Justin R.

    2009-01-01

    The current study investigated the Lecture Teaching Method and Socratic Teaching Method to determine if there was a relationship between pedagogical methods and Counselor Self-Efficacy (CSE). A course in Advanced Professional Development was utilized to determine if teaching methods could affect student perceptions of competence to practice…

  8. Integrated account of method, site selection and programme prior to the site investigation phase

    International Nuclear Information System (INIS)

    2000-12-01

    In order to dispose of the spent nuclear fuel in a safe manner, SKB plans to site a deep repository and an encapsulation plant with associated canister fabrication and transportation system. After an integrated evaluation of feasibility studies and other material, SKB will proceed with investigations of the rock and studies regarding establishment of the deep disposal system in the municipality of Oskarshamn or in Northern Uppland. The plans also include further study of the prospects for a deep repository in the municipality of Nykoeping. In the municipality of Oskarshamn, SKB plans further studies of a siting of the deep repository at Simpevarp. There SKB wants to initiate site investigations with test drilling. For the encapsulation plant, SKB wants to continue studying a siting at CLAB. In Northern Uppland, SKB plans to study two siting alternatives for the deep repository. One is Forsmark in the municipality of Oesthammar, where SKB wants to initiate a site investigation with test drilling. The other is Tierp north of Skutskaer, where SKB intends to start test drilling in an area north of Tierp. First, however, a suitable drilling area with possible transport solutions needs to be defined. This alternative requires the participation of the municipalities of both Tierp and Aelvkarleby. A siting of the encapsulation plant in Northern Uppland will also be studied. For the municipality of Nykoeping, SKB plans to conduct a new safety assessment for the Fjaellveden area, based on data from previous investigations as well as additional studies of how a deep repository could be arranged. SKB will thereby gather data from yet another geographic and geological region beyond those that are prioritized. No test drilling is planned in Nykoeping. The goal of the site investigation phase is to obtain all permits needed to build the planned facilities. It will take an estimated 7 - 8 years to assemble the requisite supporting material, carry out consultations, compile siting

  9. Development of an investigation method for redox condition of rocks by self potential (SP) method

    International Nuclear Information System (INIS)

    Kubota, Kenji; Inohara, Yoshiki; Oyama, Takahiro

    2012-01-01

    One of the major issues in subsurface disposal of low level radioactive wastes is that long term behaviors of sedimentary rocks can be affected by geochemical factors. Redox conditions can affect to corrosion of metal included in artificial barrier or wastes and adsorption characteristics of a nuclide. Therefore, it is necessary to develop a method for evaluating the redox conditions around natural barrier at waste facilities. In general, geochemical properties are acquired by rock samples or water sampling at a borehole. However, there is a possibility not to acquire data we want to evaluate. If geophysical methods are applied, redox conditions can be evaluated widely and briefly. There is a possibility that self potential (SP) and redox conditions have a correlation. So we have conducted self potential method around test caverns where redox front can be observed at the Rokkasho site. The results demonstrated that self potential decreased around redox front. There was a positive correlation between self potential and pH. One of the factors of self potential change is difference of elevation, however, self potential change around redox front was larger than that expected from elevation difference. Zeta potential is one of the important factors for determination of self potential, and it had a correlation with self potential or pH. Therefore, there is a possibility that self potential change occurs by geochemical condition changes around redox front, and redox condition can be detected by self potential method. (author)

  10. An analytical investigation on unsteady motion of vertically falling spherical particles in non-Newtonian fluid by Collocation Method

    Directory of Open Access Journals (Sweden)

    M. Rahimi-Gorji

    2015-06-01

    Full Text Available An analytical investigation is applied for unsteady motion of a rigid spherical particle in a quiescent shear-thinning power-law fluid. The results were compared with those obtained from Collocation Method (CM and the established Numerical Method (Fourth order Runge–Kutta scheme. It was shown that CM gave accurate results. Collocation Method (CM and Numerical Method are used to solve the present problem. We obtained that the CM which was used to solve such nonlinear differential equation with fractional power is simpler and more accurate than series method such as HPM which was used in some previous works by others but the new method named Akbari-Ganji’s Method (AGM is an accurate and simple method which is slower than CM for solving such problems. The terminal settling velocity—that is the velocity at which the net forces on a falling particle eliminate—for three different spherical particles (made of plastic, glass and steel and three flow behavior index n, in three sets of power-law non-Newtonian fluids was investigated, based on polynomial solution (CM. Analytical results obtained indicated that the time of reaching the terminal velocity in a falling procedure is significantly increased with growing of the particle size that validated with Numerical Method. Further, with approaching flow behavior to Newtonian behavior from shear-thinning properties of flow (n → 1, the transient time to achieving the terminal settling velocity is decreased.

  11. Numerical Investigations on Several Stabilized Finite Element Methods for the Stokes Eigenvalue Problem

    Directory of Open Access Journals (Sweden)

    Pengzhan Huang

    2011-01-01

    Full Text Available Several stabilized finite element methods for the Stokes eigenvalue problem based on the lowest equal-order finite element pair are numerically investigated. They are penalty, regular, multiscale enrichment, and local Gauss integration method. Comparisons between them are carried out, which show that the local Gauss integration method has good stability, efficiency, and accuracy properties, and it is a favorite method among these methods for the Stokes eigenvalue problem.

  12. Spectral and spectral-frequency methods of investigating atmosphereless bodies of the Solar system

    International Nuclear Information System (INIS)

    Busarev, Vladimir V; Prokof'eva-Mikhailovskaya, Valentina V; Bochkov, Valerii V

    2007-01-01

    A method of reflectance spectrophotometry of atmosphereless bodies of the Solar system, its specificity, and the means of eliminating basic spectral noise are considered. As a development, joining the method of reflectance spectrophotometry with the frequency analysis of observational data series is proposed. The combined spectral-frequency method allows identification of formations with distinctive spectral features, and estimations of their sizes and distribution on the surface of atmospherelss celestial bodies. As applied to investigations of asteroids 21 Lutetia and 4 Vesta, the spectral frequency method has given us the possibility of obtaining fundamentally new information about minor planets. (instruments and methods of investigation)

  13. A Numerical Investigation of CFRP-Steel Interfacial Failure with Material Point Method

    International Nuclear Information System (INIS)

    Shen Luming; Faleh, Haydar; Al-Mahaidi, Riadh

    2010-01-01

    The success of retrofitting steel structures by using the Carbon Fibre Reinforced Polymers (CFRP) significantly depends on the performance and integrity of CFRP-steel joint and the effectiveness of the adhesive used. Many of the previous numerical studies focused on the design and structural performance of the CFRP-steel system and neglected the mechanical responses of adhesive layer, which results in the lack of understanding in how the adhesive layer between the CFRP and steel performs during the loading and failure stages. Based on the recent observation on the failure of CFRP-steel bond in the double lap shear tests, a numerical approach is proposed in this study to simulate the delamination process of CFRP sheet from steel plate using the Material Point Method (MPM). In the proposed approach, an elastoplasticity model with a linear hardening and softening law is used to model the epoxy layer. The MPM, which does not employ fixed mesh-connectivity, is employed as a robust spatial discretization method to accommodate the multi-scale discontinuities involved in the CFRP-steel bond failure process. To demonstrate the potential of the proposed approach, a parametric study is conducted to investigate the effects of bond length and loading rates on the capacity and failure modes of CFRP-steel system. The evolution of the CFRP-steel bond failure and the distribution of stress and strain along bond length direction will be presented. The simulation results not only well match the available experimental data but also provide a better understanding on the physics behind the CFRP sheet delamination process.

  14. Computer Anti-forensics Methods and their Impact on Computer Forensic Investigation

    OpenAIRE

    Pajek, Przemyslaw; Pimenidis, Elias

    2009-01-01

    Electronic crime is very difficult to investigate and prosecute, mainly\\ud due to the fact that investigators have to build their cases based on artefacts left\\ud on computer systems. Nowadays, computer criminals are aware of computer forensics\\ud methods and techniques and try to use countermeasure techniques to efficiently\\ud impede the investigation processes. In many cases investigation with\\ud such countermeasure techniques in place appears to be too expensive, or too\\ud time consuming t...

  15. Investigating the Effects of a Math-Enhanced Agricultural Teaching Methods Course

    Science.gov (United States)

    Stripling, Christopher T.; Roberts, T. Grady

    2013-01-01

    Numerous calls have been made for agricultural education to support core academic subject matter including mathematics. Previous research has shown that the incorporation of mathematics content into a teaching methods course had a positive effect on preservice teachers' mathematics content knowledge. The purpose of this study was to investigate…

  16. Investigation of noise in gear transmissions by the method of mathematical smoothing of experiments

    Science.gov (United States)

    Sheftel, B. T.; Lipskiy, G. K.; Ananov, P. P.; Chernenko, I. K.

    1973-01-01

    A rotatable central component smoothing method is used to analyze rotating gear noise spectra. A matrix is formulated in which the randomized rows correspond to various tests and the columns to factor values. Canonical analysis of the obtained regression equation permits the calculation of optimal speed and load at a previous assigned noise level.

  17. Self-Esteem and Method Effects Associated with Negatively Worded Items: Investigating Factorial Invariance by Sex

    Science.gov (United States)

    DiStefano, Christine; Motl, Robert W.

    2009-01-01

    The Rosenberg Self-Esteem scale (RSE) has been widely used in examinations of sex differences in global self-esteem. However, previous examinations of sex differences have not accounted for method effects associated with item wording, which have consistently been reported by researchers using the RSE. Accordingly, this study examined the…

  18. Investigation of sol-gel transition by rheological methods. Part I. Experimental methods.

    Directory of Open Access Journals (Sweden)

    KUDRYAVTSEV Pavel Gennadievich

    2017-08-01

    Full Text Available In this work rheological studies of the gelling process were carried out. We have developed a measuring system for studying the rheology of the gelation process. It consisted of several measuring cells of the Weiler-Rebinder type, system for automatic regulation of the composition of the medium and hermostabilization system. This complex is designed to measure the dependence of the value of the ultimate shear stress as a function of time, from the start of the sol-gel transition to the complete conversion of the sol to the gel. The developed device has a wide range of measured values of critical shear stresses τ0 = (0,05÷50000 Dyne/cm2. Using the developed instrument, it was possible to establish the shape of the initial section of the curve τ0 = f(t and develop a methodology for more accurate determination of gelation time. The developed method proved that the classical method for determining the start time of the sol-gel transition using the point of intersection of the tangent to the linear part of the rheological curve τ0 = f(t,gives significantly distorted results. A new phenomenon has been discovered: the kinetic curves in the coordinates of the Avrami-Erofeev-Bogolyubov equation have an inflection point which separates the kinetic curve into two parts, the initial and the final. It was found that the constant k in the Avrami–Erofeev–Bogolyubov quation does not depend on the temperature and is the same for both the initial and final parts of the kinetic curve. It depends only on the chemical nature of the reacting system. It was found that for the initial section of the kinetic curves, the value of the parameter n in the Avrami-Erofeev-Bogolyubov equation was n = 23,4±2,8 and, unlike the final section of the rheological curve, does not depend on temperature. A large value of this parameter can be interpreted as the average number of directions of growth of a fractal aggregate during its growth. The value of this parameter depends

  19. Investigation of the Adaptability of Transient Stability Assessment Methods to Real-Time Operation

    OpenAIRE

    Weckesser, Johannes Tilman Gabriel; Jóhannsson, Hjörtur; Sommer, Stefan; Østergaard, Jacob

    2012-01-01

    In this paper, an investigation of the adaptability of available transient stability assessment methods to real-time operation and their real-time performance is carried out. Two approaches based on Lyapunov’s method and the equal area criterion are analyzed. The results allow to determine the runtime of each method with respect to the number of inputs. Furthermore, it allows to identify, which method is preferable in case of changes in the power system such as the integration of distributed ...

  20. Investigation by perturbative and analytical method of electronic properties of square quantum well under electric field

    Directory of Open Access Journals (Sweden)

    Mustafa Kemal BAHAR

    2010-06-01

    Full Text Available In this study, the effects of applied electric field on the isolated square quantum well was investigated by analytic and perturbative method. The energy eigen values and wave functions in quantum well were found by perturbative method. Later, the electric field effects were investigated by analytic method, the results of perturbative and analytic method were compared. As well as both of results fit with each other, it was observed that externally applied electric field changed importantly electronic properties of the system.

  1. A method to investigate inter-aquifer leakage using hydraulics and multiple environmental tracers

    Science.gov (United States)

    Priestley, Stacey; Love, Andrew; Wohling, Daniel; Post, Vincent; Shand, Paul; Kipfer, Rolf; Tyroller, Lina

    2016-04-01

    Informed aquifer management decisions regarding sustainable yields or potential exploitation require an understanding of the groundwater system (Alley et al. 2002, Cherry and Parker 2004). Recently, the increase in coal seam gas (CSG) or shale gas production has highlighted the need for a better understanding of inter-aquifer leakage and contaminant migration. In most groundwater systems, the quantity or location of inter-aquifer leakage is unknown. Not taking into account leakage rates in the analysis of large scale flow systems can also lead to significant errors in the estimates of groundwater flow rates in aquifers (Love et al. 1993, Toth 2009). There is an urgent need for robust methods to investigate inter-aquifer leakage at a regional scale. This study builds on previous groundwater flow and inter-aquifer leakage studies to provide a methodology to investigate inter-aquifer leakage in a regional sedimentary basin using hydraulics and a multi-tracer approach. The methodology incorporates geological, hydrogeological and hydrochemical information in the basin to determine the likelihood and location of inter-aquifer leakage. Of particular benefit is the analysis of hydraulic heads and environmental tracers at nested piezometers, or where these are unavailable bore couplets comprising bores above and below the aquitard of interest within a localised geographical area. The proposed methodology has been successful in investigating inter-aquifer leakage in the Arckaringa Basin, South Australia. The suite of environmental tracers and isotopes used to analyse inter-aquifer leakage included the stable isotopes of water, radiocarbon, chloride-36, 87Sr/86Sr and helium isotopes. There is evidence for inter-aquifer leakage in the centre of the basin ~40 km along the regional flow path. This inter-aquifer leakage has been identified by a slight draw-down in the upper aquifer during pumping in the lower aquifer, overlap in Sr isotopes, δ2H, δ18O and chloride

  2. Investigation of Tension Forces in A Stay Cable System of A Road Bridge Using Vibration Methods

    Directory of Open Access Journals (Sweden)

    Hawryszków Paweł

    2015-01-01

    Full Text Available In the article author presents method of investigation of tension forces in stay cable systems using dynamical methods. Research was carried out during stay cable system installation on WN-24 viaduct near Poznań, that is way it was possible to compare tension forces indicated directly by devices using for tensioning of cable-stayed bridges with results achieved indirectly by means of dynamical methods. Discussion of results was presented. Advantages of dynamical methods and possible fields of application was described. This method, which has been rarely used before, may occur interesting alternative in diagnostics of bridges in comparison to traditional methods.

  3. Introducing Students to the Application of Statistics and Investigative Methods in Political Science

    Science.gov (United States)

    Wells, Dominic D.; Nemire, Nathan A.

    2017-01-01

    This exercise introduces students to the application of statistics and its investigative methods in political science. It helps students gain a better understanding and a greater appreciation of statistics through a real world application.

  4. An injected gamma-tracer method for soil-moisture movement investigations in arid zones

    International Nuclear Information System (INIS)

    Nair, A.R.; Navada, S.V.; Rao, S.M.

    1980-01-01

    A method for the in-situ determination of soil-moisture transport rates using K 3 60 Co(CN) 6 is discussed. The tracer compares well with tritiated water in laboratory investigations and the results obtained in limited field studies are very encouraging. The method promises to be of specific interest in arid-zone investigations where the soil-moisture fluxes in liquid and vapour phases could cause complications for tritium tracer data interpretation. (author)

  5. Investigation of evaluation method for marine radiological impact during an accident

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-15

    In 2012, JNES investigated the evaluation method, long-term seawater and marine deposition for release and diffusion to the ocean at the accident, and marine impact assessment code, in Japan and overseas. Also, the foreign regulations for marine radiological impact (direct release to ocean from the facilities and fallout on marine, etc.) were investigated. Furthermore, the index (e.g., intervention level) at emergency control in USA and Europe were investigated. (author)

  6. Investigation of evaluation method for marine radiological impact during an accident

    International Nuclear Information System (INIS)

    2013-01-01

    In 2012, JNES investigated the evaluation method, long-term seawater and marine deposition for release and diffusion to the ocean at the accident, and marine impact assessment code, in Japan and overseas. Also, the foreign regulations for marine radiological impact (direct release to ocean from the facilities and fallout on marine, etc.) were investigated. Furthermore, the index (e.g., intervention level) at emergency control in USA and Europe were investigated. (author)

  7. A pilot investigation to optimise methods for a future satiety preload study

    OpenAIRE

    Hobden, Mark R.; Guérin-Deremaux, Laetitia; Commane, Daniel M.; Rowland, Ian; Gibson, Glenn R.; Kennedy, Orla B.

    2017-01-01

    Background Preload studies are used to investigate the satiating effects of foods and food ingredients. However, the design of preload studies is complex, with many methodological considerations influencing appetite responses. The aim of this pilot investigation was to determine acceptability, and optimise methods, for a future satiety preload study. Specifically, we investigated the effects of altering (i) energy intake at a standardised breakfast (gender-specific or non-gender specific), an...

  8. A longitudinal, mixed methods investigation of newly qualified nurses' workplace stressors and stress experiences during transition.

    Science.gov (United States)

    Halpin, Yvonne; Terry, Louise M; Curzio, Joan

    2017-11-01

    To investigate transition in newly qualified nurses through an exploration of their stressors and stress experiences during their first 12 months postqualifying. Globally, thousands of new nurses qualify annually. They are crucial for the profession and healthcare service delivery. Work-related stress has multiple serious consequences, yet there is a lack of robust, empirical evidence that directly analyses newly qualified nurses and the stress they feel and experience in the workplace. Understanding what causes newly qualified nurses' stress is vital to retaining and nurturing this vital component of the workforce. Longitudinal, explanatory sequential mixed methods, cohort study. At the point of qualification (n = 288), 6 months postqualifying (n = 107) and 12 months postqualifying (n = 86), newly qualified nurses completed the Nursing Stress Scale, with 14 completing a one-to-one interview at 12 months postqualifying. Data were collected from 2010 - 2012. Inferential statistics, "thematic analysis" and "side-by-side comparisons in a discussion" were used for analysis. Workload was consistently the highest reported stressor with inadequate staffing and managing multiple role demands given as explanations. Incivility within the workplace was a noted stressor. Conversely, being part of "a good team" provided a civil, supportive, facilitative work environment. Entering nurse education with previous healthcare experience had a mediating effect on the reported frequency of stressors. Newly qualified nurses encounter multiple work-related stressors over their first 12 months postqualifying, which are intrinsically entwined with their transition. Employing organizations need to be more proactive in managing their workload and addressing workplace incivility. © 2017 John Wiley & Sons Ltd.

  9. Conhecimento, atitude e prática sobre métodos anticoncepcionais entre adolescentes gestantes Knowledge, attitudes, and practices on previous use of contraceptive methods among pregnant teenagers

    Directory of Open Access Journals (Sweden)

    Márcio Alves Vieira Belo

    2004-08-01

    describe the knowledge, attitudes and practices related to previous contraceptive methods used among pregnant teenagers as well as to outline some sociodemographic characteristics and sexual practices. METHODS: An observational study associated to the KAP (Knowledge, Attitudes, and Practices survey was carried out in 156 pregnant teenagers aged 19 years or more. A structured questionnaire was applied before their first prenatal visit from October 1999 to August 2000. Univariate and bivariate analyses were performed using Pearson's and Yates' chi-square test and logistic regression. RESULTS: The adolescents had an average age of 16.1 years and most were in their first pregnancy (78.8%. Average age of menarche was 12.2 years and their first sexual intercourse was at the age of 14.5 years. Condoms (99.4% and oral contraceptives (98% were the most common contraceptive methods known. Of all, 67.3% were not using any contraceptive method before getting pregnant. The main reason reported for not using any contraceptive method was wanting to get pregnant (24.5%. The older ones who reported having religious beliefs and had a higher socioeconomic status had better knowledge on contraceptive methods. Teenagers who had had previous pregnancies reported more often use of contraceptive methods before getting pregnant. CONCLUSIONS: The pregnant teenagers showed to have adequate knowledge of contraceptive methods and agreed to use them throughout their teenage years. Religion, age group, and socioeconomic status were directly related to their knowledge on contraceptive methods, and multiple pregnancies brought more awareness on that. Of all, 54% had used any contraceptive on first sexual intercourse but their use decreased over time and shortly after their first intercourse the studied teenagers got pregnant.

  10. Using the Scientific Method to Engage Mathematical Modeling: An Investigation of pi

    Science.gov (United States)

    Archer, Lester A. C.; Ng, Karen E.

    2016-01-01

    The purpose of this paper is to explain how to use the scientific method as the framework to introduce mathematical model. Two interdisciplinary activities, targeted for students in grade 6 or grade 7, are explained to show the application of the scientific method while building a mathematical model to investigate the relationship between the…

  11. Investigation of the Adaptability of Transient Stability Assessment Methods to Real-Time Operation

    DEFF Research Database (Denmark)

    Weckesser, Johannes Tilman Gabriel; Jóhannsson, Hjörtur; Sommer, Stefan

    2012-01-01

    In this paper, an investigation of the adaptability of available transient stability assessment methods to real-time operation and their real-time performance is carried out. Two approaches based on Lyapunov’s method and the equal area criterion are analyzed. The results allow to determine...

  12. Lung mucociliary transport function in chronic bronchitis and radionuclide methods of its investigation (a review)

    International Nuclear Information System (INIS)

    Vyrenkova, N.Yu.; Faradzheva, N.A.

    1989-01-01

    Several methods for studying lung clearance of smokers and non-smoking patients with chronic bronchitis (CB) are described. Modified technique for investigating mucociliary transport (MCT) in CB patients, using 99m Tc-macroaggregate of human serum albumin, is suggested. The method enables to examine more patients and obtain the most comprehensive data on MCT state on any level of tracheobronchial tree

  13. A Mixed-Methods Study Investigating the Relationship between Media Multitasking Orientation and Grade Point Average

    Science.gov (United States)

    Lee, Jennifer

    2012-01-01

    The intent of this study was to examine the relationship between media multitasking orientation and grade point average. The study utilized a mixed-methods approach to investigate the research questions. In the quantitative section of the study, the primary method of statistical analyses was multiple regression. The independent variables for the…

  14. Further Investigating Method Effects Associated with Negatively Worded Items on Self-Report Surveys

    Science.gov (United States)

    DiStefano, Christine; Motl, Robert W.

    2006-01-01

    This article used multitrait-multimethod methodology and covariance modeling for an investigation of the presence and correlates of method effects associated with negatively worded items on the Rosenberg Self-Esteem (RSE) scale (Rosenberg, 1989) using a sample of 757 adults. Results showed that method effects associated with negative item phrasing…

  15. Radiotracer investigation of the cold-vapour atomic absorption method of analysis for trace mercury

    International Nuclear Information System (INIS)

    Stuart, D.C.

    1978-01-01

    Because of certain problems found in application of the atomic absorption method for trace analysis of mercury, a careful check of the procedures used was undertaken, with radiotracer mercury to facilitate the investigation. The results obtained, in conjunction with those of sample ashing procedures, indicate that the method is less straightforward than its simplicity suggests. (Auth.)

  16. Investigation into the value of the seismic methods in delineating structure in southwestern Ontario

    Energy Technology Data Exchange (ETDEWEB)

    Hodgson, J H

    1948-12-31

    This paper constitutes the final report on a project that investigated the possibilities of seismic methods to delineate Palaeozoic structures in areas of hydrocarbon exploration in south-western Ontario. It begins with an introduction on the theory and practice of seismic reflection prospecting and the general Palaeozoic geology of the study area. It then describes the equipment used, preliminary investigations (alignment of instruments, velocity determinations), and field tests conducted over various hydrocarbon prospects. Finally, the feasibility of using seismic methods in the area is discussed along with reasons for difficulties experienced in the investigation.

  17. Investigation of periodic systems by means of the generalized Hill method

    International Nuclear Information System (INIS)

    Baitin, A.V.; Ivanov, A.A.

    1994-01-01

    We propose the new method of investigation of infinite periodic determination which is a generalized Hill method. This method has been used for finding of the characteristic value for the Hill equation. finding the band structure of the one-dimensional periodic and obtaining of the dispersion equation for the electromagnetic wave propagation in the waveguide by plasma arbitrary periodic density modulation by plasma arbitrary periodic density modulation

  18. Technical and technological investigation of cultural heritage: experience in applications of spectroscopic methods

    Directory of Open Access Journals (Sweden)

    Grigorieva I.A.

    2017-01-01

    Full Text Available Physical and chemical methods of analysis are indispensable for restoration, study of painting techniques, examination and attribution of works of art. Development of new directions of investigations as well as improvements in sample preparation allow applying non-destructive analysis methods, minimizing amount of matter used to obtain informative spectra, preventing alteration and destruction of samples in the course of investigation. This paper observes the examples of applying optical and spectral methods, including molecular spectral analysis and electron microscopy, for study of binding media and pigments of painting and archaeological artifacts.

  19. Comparison of different methods for work accidents investigation in hospitals: A Portuguese case study.

    Science.gov (United States)

    Nunes, Cláudia; Santos, Joana; da Silva, Manuela Vieira; Lourenço, Irina; Carvalhais, Carlos

    2015-01-01

    The hospital environment has many occupational health risks that predispose healthcare workers to various kinds of work accidents. This study aims to compare different methods for work accidents investigation and to verify their suitability in hospital environment. For this purpose, we selected three types of accidents that were related with needle stick, worker fall and inadequate effort/movement during the mobilization of patients. A total of thirty accidents were analysed with six different work accidents investigation methods. The results showed that organizational factors were the group of causes which had the greatest impact in the three types of work accidents. The methods selected to be compared in this paper are applicable and appropriate for the work accidents investigation in hospitals. However, the Registration, Research and Analysis of Work Accidents method (RIAAT) showed to be an optimal technique to use in this context.

  20. Numerical investigations on contactless methods for measuring critical current density in HTS: application of modified constitutive-relation method

    International Nuclear Information System (INIS)

    Kamitani, A.; Takayama, T.; Itoh, T.; Ikuno, S.

    2011-01-01

    A fast method is proposed for calculating the shielding current density in an HTS. The J-E constitutive relation is modified so as not to change the solution. A numerical code is developed on the basis of the proposed method. The permanent magnet method is successfully simulated by means of the code. A fast method has been proposed for calculating the shielding current density in a high-temperature superconducting thin film. An initial-boundary-value problem of the shielding current density cannot be always solved by means of the Runge-Kutta method even when an adaptive step-size control algorithm is incorporated to the method. In order to suppress an overflow in the algorithm, the J-E constitutive relation is modified so that its solution may satisfy the original constitutive relation. A numerical code for analyzing the shielding current density has been developed on the basis of this method and, as an application of the code, the permanent magnet method for measuring the critical current density has been investigated numerically.

  1. Strong copper(II) species in estuarine and sea waters investigated by a method with high detection window.

    Science.gov (United States)

    Alberti, Giancarla; Biesuz, Raffaela; D'Agostino, Girolamo; Scarponi, Giuseppe; Pesavento, Maria

    2007-02-15

    The distribution of copper(II) in species of different stability in some estuarine and sea water samples (Adriatic Sea) was investigated by a method based on the sorption of the metal ion on a strongly sorbing resin, Chelex 100, whose sorbing properties have been previously characterized. From them, it is possible to predict very high values of detection windows at the considered conditions, for example side reaction coefficient as high as 10(10) at pH 7.5. Strong copper(II) species in equilibrium with Chelex 100 were detected, at concentration 2-20nM, with a reaction coefficient approximately 10(10.6) at pH 7.45 in sea water, strictly depending on the acidity. They represent 50-70% of the total metal ion and are the strongest copper(II) complexes found in sea water. Weak complexes too were detected in all the samples, with reaction coefficient lower than ca. 10(9) at the same pH. The method applied, named resin titration (RT), was described in a previous investigation, and is here modified in order to be carried out on oceanographic boat during a cruise in the Adriatic Sea.

  2. Study on Developments in Accident Investigation Methods: A Survey of the 'State-of-the-Art'

    International Nuclear Information System (INIS)

    Hollnagel, Erik; Speziali, Josephine

    2008-01-01

    The objective of this project was to survey the main accident investigation methods that have been developed since the early or mid-1990s. The motivation was the increasing frequency of accidents that defy explanations in simple terms, for instance cause-effect chains or 'human error'. Whereas the complexity of socio-technical systems is steadily growing across all industrial domains, including nuclear power production, accident investigation methods are only updated when their inability to account for novel types of accidents and incidents becomes inescapable. Accident investigation methods therefore typically lag behind the socio-technological developments by 20 years or more. The project first compiled a set of methods from the recognised scientific literature and in major major research and development programs, excluding methods limited to risk assessment, technological malfunctions, human reliability, and safety management methods. An initial set of 21 methods was further reduced to seven by retaining only prima facie accident investigation methods and avoiding overlapping or highly similar methods. The second step was to develop a set of criteria used to characterise the methods. The starting point was Perrow's description of normal accidents in socio-technical systems, which used the dimensions of coupling, going from loose to tight, and interactions, going from linear to complex. For practical reasons, the second dimension was changed to that of tractability or how easy it is to describe the system, where the sub-criteria are the level of detail, the availability of an articulated model, and the system dynamics. On this basis the seven selected methods were characterised in terms of the systems - or conditions - they could account for, leading to the following four groups: methods suitable for systems that are loosely coupled and tractable, methods suitable for systems that are tightly coupled and tractable, methods suitable for systems that are loosely

  3. How Do Zoos "Talk" to Their General Visitors? Do Visitors "Listen"? A Mixed Method Investigation of the Communication between Modern Zoos and Their General Visitors

    Science.gov (United States)

    Roe, Katie; McConney, Andrew; Mansfield, Caroline F.

    2014-01-01

    Modern zoos utilise a variety of education tools for communicating with visitors. Previous research has discussed the benefits of providing multiple education communications, yet little research provides an indication of what communications are being employed within zoos today. This research is a two-phased, mixed-methods investigation into the…

  4. Investigation of the Section Thickness Measurement in Tomosynthesis by Thin Metal Plate Edge Method.

    Science.gov (United States)

    Ikeno, Kaoru; Akita, Tsunemichi; Hanai, Kozo; Muramatsu, Yoshihisa

    When performing tomosynthesis, the section thickness needs to be set depending on a radiographic part and its diagnostic purpose. However, the section thickness in tomosynthesis has not been clearly defined and its measurement method has not been established yet. In this study, we devised the alternative measurement method to diagnose the section thickness using an edge of thin metal plate, and compared with the simulation results, the wire and bead method reported in the previous papers. The tomographic image of the thin metal plate positioned on the table top inclining 30 degrees, which showed the edge spread function (ESF) of each tomographic height, was taken, and then the line spread function (LSF) was obtained by differentiating the ESF image. For the next, a profile curve was plotted by maximum values of LSF of each tomographic height, and a section thickness was calculated using the full width at half maximum (FWHM) of the profile curve. The edge method derived the section thickness close to the simulation results than the other methods. Further, the section thickness depends on the thickness of the metal plate and not the material. The thickness of the metal plate suitable for the evaluation of section thickness is 0.3 mm that is equivalent to pixel size of the flat panel detector (FPD). We conducted quantitative verification to establish the measurement method of the section thickness. The edge method is a useful technique as well as the wire and bead method for grasping basic characteristics of an imaging system.

  5. Investigation of a New Spectrophotometric Method for the analysis of carbohydrates using glucose as model

    International Nuclear Information System (INIS)

    Hussain, Z.; Ali, A.; Shah, N.U.; Khan, K.M.

    2013-01-01

    Carbohydrates are biomolecule of significant importance. Its analysis is of prime importance in the clinical investigations, delivery of medicines and quality control operations of food and fuel products. Based on its importance a novel spectrophotometric method was investigated for the trace analysis of carbohydrates using glucose as model carbohydrate. This method is based on glucosazation followed by oxidation of the glucosazone with acidified iron (III) chloride. Oxidation of the glucsazone is necessary for enhancing the color intensity and optimum conditions were investigated for the process. All the absorbance measurements were carried out using 390 nm as gamma max. The ratio of the reactants was 1: 1.5: 0.1 mole for the glucose, phenyl hydrazine and iron (III) chloride. This method was used for the analysis of carbohydrates in real samples from plants, industrial products, blood and urine using glucose as reference. (author)

  6. Investigation of previously implicated genetic variants in chronic tic disorders

    DEFF Research Database (Denmark)

    Abdulkadir, Mohamed; Londono, Douglas; Gordon, Derek

    2017-01-01

    with those from a large independent case-control cohort. After quality control 71 SNPs were available in 371 trios; 112 SNPs in 179 trios; and 3 SNPs in 192 trios. 17 were candidate SNPs implicated in TS and 2 were implicated in obsessive-compulsive disorder (OCD) or autism spectrum disorder (ASD); 142 were......Genetic studies in Tourette syndrome (TS) are characterized by scattered and poorly replicated findings. We aimed to replicate findings from candidate gene and genome-wide association studies (GWAS). Our cohort included 465 probands with chronic tic disorder (93% TS) and both parents from 412...... families (some probands were siblings). We assessed 75 single nucleotide polymorphisms (SNPs) in 465 parent-child trios; 117 additional SNPs in 211 trios; and 4 additional SNPs in 254 trios. We performed SNP and gene-based transmission disequilibrium tests and compared nominally significant SNP results...

  7. Investigation of source location determination from Magsat magnetic anomalies: The Euler method approach

    Science.gov (United States)

    Ravat, Dhananjay

    1996-01-01

    The applicability of the Euler method of source location determination was investigated on several model situations pertinent to satellite-data scale situations as well as Magsat data of Europe. Our investigations enabled us to understand the end-member cases for which the Euler method will work with the present satellite magnetic data and also the cases for which the assumptions implicit in the Euler method will not be met by the present satellite magnetic data. These results have been presented in one invited lecture at the Indo-US workshop on Geomagnetism in Studies of the Earth's Interior in August 1994 in Pune, India, and at one presentation at the 21st General Assembly of the IUGG in July 1995 in Boulder, CO. A new method, called Anomaly Attenuation Rate (AAR) Method (based on the Euler method), was developed during this study. This method is scale-independent and is appropriate to locate centroids of semi-compact three dimensional sources of gravity and magnetic anomalies. The method was presented during 1996 Spring AGU meeting and a manuscript describing this method is being prepared for its submission to a high-ranking journal. The grant has resulted in 3 papers and presentations at national and international meetings and one manuscript of a paper (to be submitted shortly to a reputable journal).

  8. Investigation of acoustic field near to elastic thin plate using integral method

    Directory of Open Access Journals (Sweden)

    В.І. Токарев

    2004-01-01

    Full Text Available  Investigation of acoustic field near to elastic thin plate using  integral method The influence of boundary conditions on sound wave propagation, radiation and transmission through thin elastic plate is investigated. Necessary for that numerical model was found using the Helmholtz equation and equation of oscilated plate by means of integral formulation of the solution for acoustic fields near to elastic thin plate and for bending waves of small amplitudes.

  9. High-speed photographic methods for compression dynamics investigation of laser irradiated shell target

    International Nuclear Information System (INIS)

    Basov, N.G.; Kologrivov, A.A.; Krokhin, O.N.; Rupasov, A.A.; Shikanov, A.S.

    1979-01-01

    Three methods are described for a high-speed diagnostics of compression dynamics of shell targets being spherically laser-heated on the installation ''Kal'mar''. The first method is based on the direct investigation of the space-time evolution of the critical-density region for Nd-laser emission (N sub(e) asymptotically equals 10 21 I/cm 3 ) by means of the streak photography of plasma image in the second-harmonic light. The second method involves investigation of time evolution of the second-harmonic spectral distribution by means of a spectrograph coupled with a streak camera. The use of a special laser pulse with two time-distributed intensity maxima for the irradiation of shell targets, and the analysis of the obtained X-ray pin-hole pictures constitute the basis of the third method. (author)

  10. Investigation on a coupled CFD/DSMC method for continuum-rarefied flows

    Science.gov (United States)

    Tang, Zhenyu; He, Bijiao; Cai, Guobiao

    2012-11-01

    The purpose of the present work is to investigate the coupled CFD/DSMC method using the existing CFD and DSMC codes developed by the authors. The interface between the continuum and particle regions is determined by the gradient-length local Knudsen number. A coupling scheme combining both state-based and flux-based coupling methods is proposed in the current study. Overlapping grids are established between the different grid systems of CFD and DSMC codes. A hypersonic flow over a 2D cylinder has been simulated using the present coupled method. Comparison has been made between the results obtained from both methods, which shows that the coupled CFD/DSMC method can achieve the same precision as the pure DSMC method and obtain higher computational efficiency.

  11. Interferometric investigation methods of plasma spatial characteristics on stellarators and tokamaks in submillimeter region

    International Nuclear Information System (INIS)

    Berezhnyj, V.L.; Kononenko, V.I.; Epishin, V.A.; Topkov, A.N.

    1992-01-01

    The review of interferometric methods of plasma investigation in the wave submillimeter range is given. The diagnostic schemes in stellarators and tokamaks designed for experienced thermonuclear reactors and also the perspective ones, which are still out of practice, are shown. The methods of these diagnostics, their physical principles, the main possibilities and restrictions at changes of electron density, magnetic fields (currents) and their spatial distributions are described. 105 refs.; 9 figs.; 2 tables. (author)

  12. Investigation of complexing equilibrium of polyacrylate-anion with cadmium ions by polarographic method

    Energy Technology Data Exchange (ETDEWEB)

    Avlyanov, Zh K; Kabanov, N M; Zezin, A B

    1985-01-01

    Polarographic investigation of cadmium complex with polyacrylate-anion in aqueous KCl solution is carried out. It is shown that the polarographic method allows one to define equilibrium constants of polymer metallic complex (PMC) formation even in the case when current magnitudes are defined by PMC dissociation reaction kinetic characteristics. The obtained equilibrium constants of stepped complexing provide the values of mean coordination PAAxCd complex number of approximately 1.5, that coincides with the value obtained by the potentiometric method.

  13. Investigation of complexing equilibrium of polyacrylate-anion with cadmium ions by polarographic method

    International Nuclear Information System (INIS)

    Avlyanov, Zh.K.; Kabanov, N.M.; Zezin, A.B.

    1985-01-01

    Polarographic investigation of cadmium complex with polyacrylate-anion in aqueous KCl solution is carried out. It is shown that the polarographic method allows one to define equilibrium constants of polymer metallic complex (PMC) formation even in the case, when current magnitudes are defined by PMC dissociation reaction kinetic characteristics. The obtained equilibrium constants of stepped complexing provide the values of mean coordination PAAxCd complex number of approximately 1.5, that coinsides with the value obtained by the potentiometric method

  14. The integrated circuit IC EMP transient state disturbance effect experiment method investigates

    International Nuclear Information System (INIS)

    Li Xiaowei

    2004-01-01

    Transient state disturbance characteristic study on the integrated circuit, IC, need from its coupling path outset. Through cable (aerial) coupling, EMP converts to an pulse current voltage and results in the impact to the integrated circuit I/O orifice passing the cable. Aiming at the armament system construction feature, EMP effect to the integrated circuit, IC inside the system is analyzed. The integrated circuit, IC EMP effect experiment current injection method is investigated and a few experiments method is given. (authors)

  15. Nuclear-physical methods of investigation of an element composition in samples of soils and plants

    International Nuclear Information System (INIS)

    Hushmurodov, Sh.; Botaev, N.

    2002-01-01

    Soil (ground) and vegetative covers of the Earth are one of the most responsive and specific parts of the biosphere with respect to pollution. A proper control after them is of fundamental importance in creating and protecting optical surrounding. Analysis of soils and plants is a necessary and important stage in the process of investigation of microelements' migration in biogeochemical cycles. For this purpose we studied some reserved terrains of Uzbekistan to reveal a level of their contamination by heavy metals, as well as to find out typical and territorial singularities in accumulation of a number of elements by soils and plants. In order to decrease an influence of systematic errors, and to obtain more precise and reliable data, we carried out the element analysis of the samples by different methods, such as gamma-activation analysis, neutron-activation analysis, X-ray spectral analysis, and X-ray fluorescent analysis. As a result of our investigations we have obtained rather great information, which can be used in future to estimate the conditions of the surrounding nature. The investigations allowed us to determine the content of about 40 elements, as well as to show that the data, obtained by different nuclear-physical methods, are in rather good agreement. A reproducibility of the results of the methods, determined in control measurements, depends on the concentration of the analyzed elements, and is equal to 10-35 %. A comparison of the obtained data allowed us to reveal some singularities in element composition of the investigated samples depending on their type and territorial factor. It has been revealed that the data, obtained by different methods, are in rather good agreement. Our investigations allowed us to find out a series of regularities and singularities in accumulation of elements in plants, as well as to show the possibility of using nuclear-physical methods in such investigations

  16. Application of radioisotope methods of investigation and control techniques in tube production

    International Nuclear Information System (INIS)

    Chizh, V.A.; Drabkin, L.A.

    1975-01-01

    Various spheres of radioactive isotopes application of closed and open type in tube production are described. Due to the usage of radioactive indicator method in combination with physicochemical methods and metallography new data are obtained in the theory and practice of tube centrifugal casting, rolling and pressing. Adsorption properties of lubricants and element distribution in the joint weld region of the big diameter tubes are investigated. The application of radioactive isotopes as ionizing radiation source made it possible to develop some radioisotope methods and instruments for tube wall thickness and the wall thickness difference control. Short characteristics of such instruments are given

  17. Investigation of Method for Changing Impression of Musical Piece by Changing its Tempo

    Science.gov (United States)

    Fukumoto, Makoto; Okamatsu, Keita; Matsuo, Kazuhisa

    We propose a simple method that changes impression of musical piece by changing its tempo and investigate psycho-physiological effects of the method with listening experiment. In the experiment, 8 subjects listened same musical pieces with various tempi, and analysis of heartbeat and Semantic-Differential method were used. In 6 out of 10 adjective pairs, inverted-U shapes were observed, and peak tempi of them were different. Moreover, “relaxed” evaluation might be related to listener's heart rate in rest. These results suggest possibility of constructing novel media player that changes impression of musical piece.

  18. Are Imaging and Lesioning Convergent Methods for Assessing Functional Specialisation? Investigations Using an Artificial Neural Network

    Science.gov (United States)

    Thomas, Michael S. C.; Purser, Harry R. M.; Tomlinson, Simon; Mareschal, Denis

    2012-01-01

    This article presents an investigation of the relationship between lesioning and neuroimaging methods of assessing functional specialisation, using synthetic brain imaging (SBI) and lesioning of a connectionist network of past-tense formation. The model comprised two processing "routes": one was a direct route between layers of input and output…

  19. Investigation of evaluation method for marine radiological impact during an accident

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-08-15

    In 2012, JNES carried out to investigate the measurement information of radionuclide released to the ocean at Fukushima Daiichi NPP accident, the foreign regulation for marine radiological impact, and the evaluation method for release and diffusion to the ocean at the accident inside and outside Japan. (author)

  20. Tank 48H Waste Composition and Results of Investigation of Analytical Methods

    Energy Technology Data Exchange (ETDEWEB)

    Walker , D.D. [Westinghouse Savannah River Company, AIKEN, SC (United States)

    1997-04-02

    This report serves two purposes. First, it documents the analytical results of Tank 48H samples taken between April and August 1996. Second, it describes investigations of the precision of the sampling and analytical methods used on the Tank 48H samples.

  1. Teaching Ethics in Communication Courses: An Investigation of Instructional Methods, Course Foci, and Student Outcomes

    Science.gov (United States)

    Canary, Heather E.

    2007-01-01

    This study investigates the impact of ethics instruction in communication courses on students' moral reasoning competence. Using a quasi-experiment, participants in interpersonal conflict courses and communication ethics courses were exposed to different levels of ethics instruction through a variety of instructional methods. Results indicate that…

  2. The "Frankenplasmid" Lab: An Investigative Exercise for Teaching Recombinant DNA Methods

    Science.gov (United States)

    Dean, Derek M.; Wilder, Jason A.

    2011-01-01

    We describe an investigative laboratory module designed to give college undergraduates strong practical and theoretical experience with recombinant DNA methods within 3 weeks. After deducing restriction enzyme maps for two different plasmids, students ligate the plasmids together in the same reaction, transform "E. coli" with this mixture of…

  3. An Investigation of Three Methods of Teaching Vocabulary at the Junior High Level.

    Science.gov (United States)

    Geiger, Evangeline Drury

    This study of methods of teaching vocabulary in the junior high school investigated three approaches: use of a programed text in vocabulary development that emphasized context clues, use of the programed text augmented by listening assistance, and use of the programed text augmented by a word-analysis supplement. Over 300 students with I.Q.'s…

  4. Isotopic method for investigation of process of periodic sedimentation of argillaceous suspensions

    International Nuclear Information System (INIS)

    Kohman, L.; Woznicki, T.

    1976-01-01

    The process of periodic sedimentation of kaolinic suspension in water has been investigated, by isotopic tracer method. the tracer was either the irradiated matrix material or 198 Au, adsorbed on the kaolin grains. The velocity of suspension level lowering (the sedimentation curve) and the variation in density in vertical section of sediment layer have been determined. (author)

  5. Efficiency of computerized tomography in comparison with other neuroradiological investigation methods

    International Nuclear Information System (INIS)

    Kretzschmar, H.

    1979-01-01

    Computerized tomography is considered to be a decisive and the most reliable investigation method for the diagnosis of cerebral tumors. The rate of detection of intracranial blastomas is over 90%. Supratentorial growths are more easy to prove than tumors at the posterior cranial fossa. In the group of patients examined, 97.3% of the cerebral tumors were confirmed by computerized tomography: 98.7% of these were located above the tentorium and 89.3% under the tentorium. But the diagnostic value of computerized tomography is not only due to the high growth detection rate but also to its informative power as regards the position of growths in relation to vital centres, the type of the blastomas and their space-occupying effect. Thus this investigation method permits to evaluate the complex ''space occupation'' at one glance. By the angiographic method cerebral growths are confirmed in 86% of the cases; 88.6% of these are located above the tentorium. (orig.) [de

  6. Investigation of e-Linac tube construction method and implementation suitable method for IPM e-Linac

    Directory of Open Access Journals (Sweden)

    F ghasemi

    2015-09-01

    Full Text Available The goal of electron linear accelerator project in institute for research in fundamental sciences(IPM is to build its components as many as they can in Iran. This accelerator is a traveling wave type. Investigations show that there are various techniques in forming and connecting the accelerating tube cavities. The shrinking method applied for constructing the accelerating tube is selected based on the one applied for Stanford University’s Mark III accelerator. With success in building an 8-cavity test tube and finding the problems of the method, the construction of the final accelerating tube with 24 cavities has been accomplished. The results show that the obtained frequency of 2996.5 MHz and quality factor of 11200, satisfy the design desired values.

  7. Cancer research in need of a scientific revolution: Using 'paradigm shift' as a method of investigation.

    Science.gov (United States)

    Wion, Didier; Appaix, Florence; Burruss, Meriwether; Berger, Francois; van der Sanden, Boudewijn

    2015-09-01

    Despite important human and financial resources and considerable accumulation of scientific publications, patents, and clinical trials, cancer research has been slow in achieving a therapeutic revolution similar to the one that occurred in the last century for infectious diseases. It has been proposed that science proceeds not only by accumulating data but also through paradigm shifts. Here, we propose to use the concept of 'paradigm shift' as a method of investigation when dominant paradigms fail to achieve their promises. The first step in using the 'paradigm shift' method in cancer research requires identifying its founding paradigms. In this review, two of these founding paradigms will be discussed: (i) the reification of cancer as a tumour mass and (ii) the translation of the concepts issued from infectious disease in cancer research. We show how these founding paradigms can generate biases that lead to over-diagnosis and over-treatment and also hamper the development of curative cancer therapies. We apply the 'paradigm shift' method to produce perspective reversals consistent with current experimental evidence. The 'paradigm shift' method enlightens the existence of a tumour physiologic-prophylactic-pathologic continuum. It integrates the target/antitarget concept and that cancer is also an extracellular disease. The 'paradigm shift' method has immediate implications for cancer prevention and therapy. It could be a general method of investigation for other diseases awaiting therapy.

  8. An investigation into the applicability of the semiempirical method PM7 for modeling the catalytic mechanism in the enzyme chymotrypsin.

    Science.gov (United States)

    Stewart, James J P

    2017-05-01

    The catalytic cycle for the serine protease α-chymotrypsin was investigated in an attempt to determine the suitability of using the semiempirical method PM7 in the program MOPAC for investigating enzyme-catalyzed reactions. All six classical intermediates were modeled using standard methods, and were characterized as stable minima on the potential energy surface. Using a modified saddle point optimization method, five transition states were located and verified both by vibrational and by intrinsic reaction coordinate analysis. Some individual features, such as the hydrogen bonds in the oxyanion hole, the nature of various electrostatic interactions, and the role of Met192, were examined. This involved designing and running computational experiments to model mutations that would allow features of interest, in particular the energies involved, to be isolated. Three features within the enzyme were examined in detail: the reaction site itself, where covalent bonds were made and broken, the electrostatic effects of the buried aspartate anion, a passive but essential component of the catalytic triad, and the oxyanion hole, where hydrogen bonds help stabilize charged intermediates. With one minor exception, all phenomena investigated agreed with previously-reported descriptions. This result, along with the fact that all the techniques used were relatively straightforward, leads to the recommendation that PM7 and related methods, such as PM6-D3H4, are appropriate for modeling similar enzyme-catalyzed reactions. Graphical abstract Fifth of six transition states, showing water splitting into hydroxyl anion and a proton, to form the second tetrahedral intermediate and histidinium ion. Atoms of the water molecule involved in the hydrolysis are indicated by halos.

  9. Investigation of colistin sensitivity via three different methods in Acinetobacter baumannii isolates with multiple antibiotic resistance.

    Science.gov (United States)

    Sinirtaş, Melda; Akalin, Halis; Gedikoğlu, Suna

    2009-09-01

    In recent years there has been an increase in life-threatening infections caused by Acinetobacter baumannii with multiple antibiotic resistance, which has lead to the use of polymyxins, especially colistin, being reconsidered. The aim of this study was to investigate the colistin sensitivity of A. baumannii isolates with multiple antibiotic resistance via different methods, and to evaluate the disk diffusion method for colistin against multi-resistant Acinetobacter isolates, in comparison to the E-test and Phoenix system. The study was carried out on 100 strains of A. baumannii (colonization or infection) isolated from the microbiological samples of different patients followed in the clinics and intensive care units of Uludağ University Medical School between the years 2004 and 2005. Strains were identified and characterized for their antibiotic sensitivity by Phoenix system (Becton Dickinson, Sparks, MD, USA). In all studied A. baumannii strains, susceptibility to colistin was determined to be 100% with the disk diffusion, E-test, and broth microdilution methods. Results of the E-test and broth microdilution method, which are accepted as reference methods, were found to be 100% consistent with the results of the disk diffusion tests; no very major or major error was identified upon comparison of the tests. The sensitivity and the positive predictive value of the disk diffusion method were found to be 100%. Colistin resistance in A. baumannii was not detected in our region, and disk diffusion method results are in accordance with those of E-test and broth microdilution methods.

  10. A holographic method for investigating cylindrical symmetry plasmas resulting from electric discharges

    International Nuclear Information System (INIS)

    Rosu, N.; Ralea, M.; Foca, M.; Iova, I.

    1992-01-01

    A new method based on holographic interferometry in real time with reference fringes for diagnosing gas electric discharges in cylindrical symmetry tubes is presented. A method for obtaining and quantitatively investigating interferograms obtained with a video camera is described. By studying the resulting images frame by frame and introducing the measurements into an adequate computer programme one gets a graphical recording of the radial distribution of the charged particle concentration in the plasma in any region of the tube at a given time, as well as their axial distribution. The real time evolution of certain phenomena occurring in the discharge tube can also be determined by this non-destructive method. The method is used for electric discharges in Ar at average pressures in a discharge tube with hollow cathode effect. (Author)

  11. Investigation of Compton scattering correction methods in cardiac SPECT by Monte Carlo simulations

    International Nuclear Information System (INIS)

    Silva, A.M. Marques da; Furlan, A.M.; Robilotta, C.C.

    2001-01-01

    The goal of this work was the use of Monte Carlo simulations to investigate the effects of two scattering correction methods: dual energy window (DEW) and dual photopeak window (DPW), in quantitative cardiac SPECT reconstruction. MCAT torso-cardiac phantom, with 99m Tc and non-uniform attenuation map was simulated. Two different photopeak windows were evaluated in DEW method: 15% and 20%. Two 10% wide subwindows centered symmetrically within the photopeak were used in DPW method. Iterative ML-EM reconstruction with modified projector-backprojector for attenuation correction was applied. Results indicated that the choice of the scattering and photopeak windows determines the correction accuracy. For the 15% window, fitted scatter fraction gives better results than k = 0.5. For the 20% window, DPW is the best method, but it requires parameters estimation using Monte Carlo simulations. (author)

  12. The investigation of the non-orthogonal basis expansion method for a three-fermion system

    International Nuclear Information System (INIS)

    Baoqiu Chen; Kentucky Univ., Lexington, KY

    1992-01-01

    In this paper, the non-orthogonal basis expansion method has been extended to solve a three-fermion system. The radial wavefunction of such a system is expanded in terms of a non-orthogonal Gaussian basis. All matrix elements of the Hamiltonian, including the central, tensor and spin-orbit potentials are derived in analytical forms. The new method simplifies the three-body system calculations, which are usually rather tedious by other methods. The method can be used to calculate energies for both the ground state and low excited states and has been used further to investigate the other nuclear properties of a three-body system such as Λ 3 H. (Author)

  13. Numerical Investigation of Vertical Cavity Lasers With High-Contrast Gratings Using the Fourier Modal Method

    DEFF Research Database (Denmark)

    Taghizadeh, Alireza; Mørk, Jesper; Chung, Il-Sug

    2016-01-01

    We explore the use of a modal expansion technique, Fourier modal method (FMM), for investigating the optical properties of vertical cavities employing high-contrast gratings (HCGs). Three techniques for determining the resonance frequency and quality factor (Q-factor) of a cavity mode are compared......, the scattering losses of several HCG-based vertical cavities with inplane heterostructures which have promising prospects for fundamental physics studies and on-chip laser applications, are investigated. This type of parametric study of 3D structures would be numerically very demanding using spatial...

  14. The radiation factor 'hot particles': origin, methods of investigation, characterization and risk factors

    International Nuclear Information System (INIS)

    Bonchev, Ts.; Vapirev, E.; Yanev, Y.

    1993-01-01

    The problem of hot particles (HP) is reviewed chronologically following published data. The term appeared in the 50-s when HP have been found in fallout as a result of nuclear explosions in the atmosphere. After the Chernobyl accident there is a growing interest in HP. In 1986 HP have been discovered in American nuclear power plants (NPP) and in 1992 some have been found at Kozloduy NPP in Bulgaria as well. Detection and collection methods and different approaches for HP investigation are discussed. The direct and indirect risks from HP are described. It is concluded that the problem deserves further investigation and the discovery of HP inside NPP is of special interest

  15. The radiation factor `hot particles`: origin, methods of investigation, characterization and risk factors

    Energy Technology Data Exchange (ETDEWEB)

    Bonchev, Ts; Vapirev, E; Yanev, Y

    1994-12-31

    The problem of hot particles (HP) is reviewed chronologically following published data. The term appeared in the 50-s when HP have been found in fallout as a result of nuclear explosions in the atmosphere. After the Chernobyl accident there is a growing interest in HP. In 1986 HP have been discovered in American nuclear power plants (NPP) and in 1992 some have been found at Kozloduy NPP in Bulgaria as well. Detection and collection methods and different approaches for HP investigation are discussed. The direct and indirect risks from HP are described. It is concluded that the problem deserves further investigation and the discovery of HP inside NPP is of special interest.

  16. Apparatus and methods for investigations into acoustic properties of electronic melts

    International Nuclear Information System (INIS)

    Glazov, V.M.; Timoshenko, V.I.; Kim, S.G.

    1985-01-01

    Apparatus and highly sensitive methods of systematic investigations into acoustic properties of electronic melts are described. A variant of a measuring cell to investigate agressive melts is presented. A new technique for the reception of an acoustic contact with high transmission capacity of ultrasonic wave based on utilization of clarified layers of liquid boron anhydride is described. Results of calibration tests on lead and aluminium melts point to a good agreement with literature data. High sensitivity of the above technique allows one to reveal thin structural effects in melts

  17. A numeric investigation of co-flowing liquid streams using the Lattice Boltzmann Method

    Science.gov (United States)

    Somogyi, Andy; Tagg, Randall

    2007-11-01

    We present a numerical investigation of co-flowing immiscible liquid streams using the Lattice Boltzmann Method (LBM) for multi component, dissimilar viscosity, immiscible fluid flow. When a liquid is injected into another immiscible liquid, the flow will eventually transition from jetting to dripping due to interfacial tension. Our implementation of LBM models the interfacial tension through a variety of techniques. Parallelization is also straightforward for both single and multi component models as only near local interaction is required. We compare the results of our numerical investigation using LBM to several recent physical experiments.

  18. Use of casual tree method for investigation of incidents and accidents involving radioactive materials

    International Nuclear Information System (INIS)

    Vasconcelos, Vanderley de; Senne Junior, Murillo; Marques, Raissa Oliveira

    2013-01-01

    There are many methodologies used for investigation of accidents to facilitate the search of the factors that cause these events in different areas of industry. These can be called proactive methods, if they are used before the occurrence of the events, or reactive methods that are applied after the occurrence of the incident or accident, and are used as a basis of information to prevent further events. One of these methods is the Causal Tree Method (CTM). The basic idea of this technique is that incidents and accidents result from variations in usual processes. These variations can be related to the individual, the task, the material or the environment. The tree starts with the end event (incident or accident) and works backwards. The facts relating to the end event are used in the construction of the causal tree. The end event is the starting point and only the facts that contributed to the incident or accident should be selected. The analyst has to identify and list the variations and then display them in the analytic tree, showing causal relations. The objective of this paper is to test the application of the CTM method in investigation of incidents and accidents involving radioactive materials, in order to evaluate its efficiency on finding the typical factors causing these events. (author)

  19. An analytical method for the investigation of instability of a collisionless plasma in strong magnetic fields

    International Nuclear Information System (INIS)

    Zakharov, V.U.

    1993-01-01

    An analytical method for the investigation of special types of dispersion relations is presented. In particular, analysis of the propagation of small-amplitude hydromagnetic waves in a collisionless plasma in a strong magnetic field leads to such dispersion relations. The fifth-degree dispersion relation corresponding to a particular case is considered. The necessary stability condition for a steady state and conditions for the degeneration of small-amplitude waves are derived. A comparison with other methods for the analysis of similar dispersion relations is also presented. (author)

  20. Investigation of methods for fabricating, characterizing, and transporting cryogenic inertial-confinement-fusion tartets

    International Nuclear Information System (INIS)

    Fanning, J.J.; Kim, K.

    1981-01-01

    The objective of this work is to investigate methods for fabricating, characterizing and transporting cryogenic inertial confinement fusion targets on a continuous basis. A microprocessor-based data acquisition system has been built that converts a complete target image to digital data, which are then analyzed by automated software procedures. The low temperatures required to freeze the hydrogen isotopes contained in a target is provided by a cryogenic cold chamber capable of attaining 15 K. A new method for target manipulation and positioning is studied that employs molecular gas beams to levitate a target and an electrostatic quadrupole structure to provide for its lateral containment. Since the electrostatic target-positioning scheme requires that the targets be charged, preliminary investigation has been carried out for a target-charging mechanism based on ion-bombardment

  1. Application of Different Extraction Methods for Investigation of Nonmetallic Inclusions and Clusters in Steels and Alloys

    Directory of Open Access Journals (Sweden)

    Diana Janis

    2014-01-01

    Full Text Available The characterization of nonmetallic inclusions is of importance for the production of clean steel in order to improve the mechanical properties. In this respect, a three-dimensional (3D investigation is considered to be useful for an accurate evaluation of size, number, morphology of inclusions, and elementary distribution in each inclusion particle. In this study, the application of various extraction methods (chemical extraction/etching by acid or halogen-alcohol solutions, electrolysis, sputtering with glow discharge, and so on for 3D estimation of nonmetallic Al2O3 inclusions and clusters in high-alloyed steels was examined and discussed using an Fe-10 mass% Ni alloy and an 18/8 stainless steel deoxidized with Al. Advantages and limitations of different extraction methods for 3D investigations of inclusions and clusters were discussed in comparison to conventional two-dimensional (2D observations on a polished cross section of metal samples.

  2. Investigation by tracer method of water balance in filling the gob with slurries

    International Nuclear Information System (INIS)

    Jureczko, J.; Skowronek, E.

    1977-01-01

    Results of investigations on the establishment of conditions of water flow in filling old workings with mud, in order to determine the degree of water hazard for mine workings in one of mines are given. For the inspection of flow, the stable tracer method and the neutron activation analysis were used. Chromium as a complex compound with EDTA was used as tracer. Geological and mining conditions in the area of investigations by tracers are given and the disposal of diluted stowing slurry is characterized. The method of interpretation of results is discussed in order to determine the water flow rate in the gob and to draw up the water balance on the basis of the curve of tracer travel. (author)

  3. Application of remote sensing methods and GIS in erosive process investigations

    Directory of Open Access Journals (Sweden)

    Mustafić Sanja

    2007-01-01

    Full Text Available Modern geomorphologic investigations of condition and change of the intensity of erosive process should be based on application of remote sensing methods which are based on processing of aerial and satellite photographs. Using of these methods is very important because it enables good possibilities for realizing regional relations of the investigated phenomenon, as well as the estimate of spatial and temporal variability of all physical-geographical and anthropogenic factors influencing given process. Realizing process of land erosion, on the whole, is only possible by creating universal data base, as well as by using of appropriate software, more exactly by establishing uniform information system. Geographical information system, as the most effective one, the most complex and the most integral system of information about the space enables unification as well as analytical and synthetically processing of all data.

  4. Investigation of methods for fabricating, characterizing, and transporting cryogenic inertial-confinement-fusion tartets

    Energy Technology Data Exchange (ETDEWEB)

    Fanning, J.J.; Kim, K.

    1981-01-01

    The objective of this work is to investigate methods for fabricating, characterizing and transporting cryogenic inertial confinement fusion targets on a continuous basis. A microprocessor-based data acquisition system has been built that converts a complete target image to digital data, which are then analyzed by automated software procedures. The low temperatures required to freeze the hydrogen isotopes contained in a target is provided by a cryogenic cold chamber capable of attaining 15 K. A new method for target manipulation and positioning is studied that employs molecular gas beams to levitate a target and an electrostatic quadrupole structure to provide for its lateral containment. Since the electrostatic target-positioning scheme requires that the targets be charged, preliminary investigation has been carried out for a target-charging mechanism based on ion-bombardment.

  5. Preparing investigation of methods for surveying tree seed demands among farmers in Tanzania

    DEFF Research Database (Denmark)

    Aabæk, Anders

    Insufficient seed supplies is often a major constraint on tree planting activities in developing countries. A central problem is to assess the actual demands for tree seed. This report shall, as a part of a PhD-study, prepare an investigation of different methods for surveying tree seed demands...... and preferences among private farmers in Tanzania. A framework for investigating seed demand and supply is outlined. The role of a national tree seed project in a seed supply sector is discussed and data requirements for strategy on seed procurement and tree improvement are outlined. Earlier surveys on seed...... demand pattern in Tanzania, Uganda and Nicaragua are discussed and a choice of strategy for an extensive survey of seed demand and supply in Tanzania is made. Different data collection methods and tools, e.g. quantitative and qualitative surveys and rapid rural appraisals, are described in detail...

  6. Criminal investigations: pupil pharmacological reactivity as method for assessing time since death is fallacious.

    Science.gov (United States)

    Orrico, Marco; Melotti, Roberto; Mantovani, Anna; Avesani, Barbara; De Marco, Roberto; De Leo, Domenico

    2008-12-01

    Determination of the time since death in the early postmortem period is one of the most critical issues to be faced by criminal investigators. One of the techniques is the evaluation of the pupil pharmacological reactivity. In the present work, we aim at identifying whether an objective and single method, based on pharmacological pupil reaction, is feasible or not. Between 2002 and 2003 calendar years, we observed 309 bodies, whose eyes have been each instilled apart, within 26 hours since death, with either a myotic substance or a mydriatic solution. Our results show that the real effectiveness of pupil pharmacological reactivity as method for assessing the time since death in early postmortem period is not only questionable but even highly misleading if not replaced by alternative objective physiological tests and appropriate professional judgments by the investigators.

  7. Small angle neutron scattering in polyelectrolyte solutions: investigation of polymethacrylic acid solutions by contrast variation method

    International Nuclear Information System (INIS)

    Glavata, D.; Pleshtil, I.; Kunchenko, A.B.; Ostanevich, Yu.M.

    1982-01-01

    Neutron experiments performed by the contrast (background) variation method allows to understand better the role that hydration plays in the study of macromolecules and to draw the connection between the excess scattering amplitude of hydrated molecule with its partial volume. The observed dependence of the compensation point on the degree of neutralization apparently plays an important role in the investigation of polyelectrolytes of biological origin

  8. Investigation for thermal stability of U3Si2 and protection methods

    International Nuclear Information System (INIS)

    Zhang Huiying; Sun Jichang; Sun Rongxian

    1994-08-01

    The thermal stability of U 3 Si 2 in Ar, N 2 and air, and the interaction between U 3 Si 2 and Al, Zr have been investigated by thermal analysis method. According to the results of thermal analysis, protection measures for various procedures have been improved. From the practice, it shows that the protection measures can ensure the safety of production and raise the product quality as well as reduce the cost effectively

  9. Current Proteomic Methods to Investigate the Dynamics of Histone Turnover in the Central Nervous System.

    Science.gov (United States)

    Farrelly, L A; Dill, B D; Molina, H; Birtwistle, M R; Maze, I

    2016-01-01

    Characterizing the dynamic behavior of nucleosomes in the central nervous system is vital to our understanding of brain-specific chromatin-templated processes and their roles in transcriptional plasticity. Histone turnover-the complete loss of old, and replacement by new, nucleosomal histones-is one such phenomenon that has recently been shown to be critical for cell-type-specific transcription in brain, synaptic plasticity, and cognition. Such revelations that histones, long believed to static proteins in postmitotic cells, are highly dynamic in neurons were only possible owing to significant advances in analytical chemistry-based techniques, which now provide a platform for investigations of histone dynamics in both healthy and diseased tissues. Here, we discuss both past and present proteomic methods (eg, mass spectrometry, human "bomb pulse labeling") for investigating histone turnover in brain with the hope that such information may stimulate future investigations of both adaptive and aberrant forms of "neuroepigenetic" plasticity. © 2016 Elsevier Inc. All rights reserved.

  10. Non-destructive investigations of Swiss museums objects with neutron and x-ray imaging methods

    International Nuclear Information System (INIS)

    Lehmann, E.H.; Deschler, E.; Pernet, L.; Vontobel, P.

    2004-01-01

    Many objects of archaeological relevance found in Switzerland are from the Celtic and Roman era. Because of their uniqueness in most cases it is demanded to perform any investigation with such samples non-destructively. Depending on the structure and size of the objects a transmission experiment performed either with X-ray or neutron can alight inner structures, composition, defects or the principles of the manufacturing procedures. Furthermore, the treatment by conservators and restaurateurs becomes visible in many cases. This report describes some examples of such investigations. In the case of neutron investigations, beside the transmission imaging as a radiograph the three-dimensional structure was observed with a tomography technique. For X-ray radiography, the images were obtained in the same digital format because the similar experimental method (imaging plates) was applied. It becomes evident in the described examples that the combination and complementary use of both methods (neutrons and X-ray) brings insights in different aspects of the samples properties and treatment. This approach to study museums objects stored and exhibit in Switzerland can be extrapolated to other countries where these techniques are also simultaneously available in order to investigate other objects of relevance. The European network COST-G8 entitled 'Non-destructive analysis and testing of museum objects' can help to support initiatives in this direction. (author)

  11. Investigation of modern methods of probalistic sensitivity analysis of final repository performance assessment models (MOSEL)

    International Nuclear Information System (INIS)

    Spiessl, Sabine; Becker, Dirk-Alexander

    2017-06-01

    Sensitivity analysis is a mathematical means for analysing the sensitivities of a computational model to variations of its input parameters. Thus, it is a tool for managing parameter uncertainties. It is often performed probabilistically as global sensitivity analysis, running the model a large number of times with different parameter value combinations. Going along with the increase of computer capabilities, global sensitivity analysis has been a field of mathematical research for some decades. In the field of final repository modelling, probabilistic analysis is regarded a key element of a modern safety case. An appropriate uncertainty and sensitivity analysis can help identify parameters that need further dedicated research to reduce the overall uncertainty, generally leads to better system understanding and can thus contribute to building confidence in the models. The purpose of the project described here was to systematically investigate different numerical and graphical techniques of sensitivity analysis with typical repository models, which produce a distinctly right-skewed and tailed output distribution and can exhibit a highly nonlinear, non-monotonic or even non-continuous behaviour. For the investigations presented here, three test models were defined that describe generic, but typical repository systems. A number of numerical and graphical sensitivity analysis methods were selected for investigation and, in part, modified or adapted. Different sampling methods were applied to produce various parameter samples of different sizes and many individual runs with the test models were performed. The results were evaluated with the different methods of sensitivity analysis. On this basis the methods were compared and assessed. This report gives an overview of the background and the applied methods. The results obtained for three typical test models are presented and explained; conclusions in view of practical applications are drawn. At the end, a recommendation

  12. Investigation of modern methods of probalistic sensitivity analysis of final repository performance assessment models (MOSEL)

    Energy Technology Data Exchange (ETDEWEB)

    Spiessl, Sabine; Becker, Dirk-Alexander

    2017-06-15

    Sensitivity analysis is a mathematical means for analysing the sensitivities of a computational model to variations of its input parameters. Thus, it is a tool for managing parameter uncertainties. It is often performed probabilistically as global sensitivity analysis, running the model a large number of times with different parameter value combinations. Going along with the increase of computer capabilities, global sensitivity analysis has been a field of mathematical research for some decades. In the field of final repository modelling, probabilistic analysis is regarded a key element of a modern safety case. An appropriate uncertainty and sensitivity analysis can help identify parameters that need further dedicated research to reduce the overall uncertainty, generally leads to better system understanding and can thus contribute to building confidence in the models. The purpose of the project described here was to systematically investigate different numerical and graphical techniques of sensitivity analysis with typical repository models, which produce a distinctly right-skewed and tailed output distribution and can exhibit a highly nonlinear, non-monotonic or even non-continuous behaviour. For the investigations presented here, three test models were defined that describe generic, but typical repository systems. A number of numerical and graphical sensitivity analysis methods were selected for investigation and, in part, modified or adapted. Different sampling methods were applied to produce various parameter samples of different sizes and many individual runs with the test models were performed. The results were evaluated with the different methods of sensitivity analysis. On this basis the methods were compared and assessed. This report gives an overview of the background and the applied methods. The results obtained for three typical test models are presented and explained; conclusions in view of practical applications are drawn. At the end, a recommendation

  13. Video elicitation interviews: a qualitative research method for investigating physician-patient interactions.

    Science.gov (United States)

    Henry, Stephen G; Fetters, Michael D

    2012-01-01

    We describe the concept and method of video elicitation interviews and provide practical guidance for primary care researchers who want to use this qualitative method to investigate physician-patient interactions. During video elicitation interviews, researchers interview patients or physicians about a recent clinical interaction using a video recording of that interaction as an elicitation tool. Video elicitation is useful because it allows researchers to integrate data about the content of physician-patient interactions gained from video recordings with data about participants' associated thoughts, beliefs, and emotions gained from elicitation interviews. This method also facilitates investigation of specific events or moments during interactions. Video elicitation interviews are logistically demanding and time consuming, and they should be reserved for research questions that cannot be fully addressed using either standard interviews or video recordings in isolation. As many components of primary care fall into this category, high-quality video elicitation interviews can be an important method for understanding and improving physician-patient interactions in primary care.

  14. Video Elicitation Interviews: A Qualitative Research Method for Investigating Physician-Patient Interactions

    Science.gov (United States)

    Henry, Stephen G.; Fetters, Michael D.

    2012-01-01

    We describe the concept and method of video elicitation interviews and provide practical guidance for primary care researchers who want to use this qualitative method to investigate physician-patient interactions. During video elicitation interviews, researchers interview patients or physicians about a recent clinical interaction using a video recording of that interaction as an elicitation tool. Video elicitation is useful because it allows researchers to integrate data about the content of physician-patient interactions gained from video recordings with data about participants’ associated thoughts, beliefs, and emotions gained from elicitation interviews. This method also facilitates investigation of specific events or moments during interactions. Video elicitation interviews are logistically demanding and time consuming, and they should be reserved for research questions that cannot be fully addressed using either standard interviews or video recordings in isolation. As many components of primary care fall into this category, high-quality video elicitation interviews can be an important method for understanding and improving physician-patient interactions in primary care. PMID:22412003

  15. Investigation of dispersion-relation-preserving scheme and spectral analysis methods for acoustic waves

    Science.gov (United States)

    Vanel, Florence O.; Baysal, Oktay

    1995-01-01

    Important characteristics of the aeroacoustic wave propagation are mostly encoded in their dispersion relations. Hence, a computational aeroacoustic (CAA) algorithm, which reasonably preserves these relations, was investigated. It was derived using an optimization procedure to ensure, that the numerical derivatives preserved the wave number and angular frequency of the differential terms in the linearized, 2-D Euler equations. Then, simulations were performed to validate the scheme and a compatible set of discretized boundary conditions. The computational results were found to agree favorably with the exact solutions. The boundary conditions were transparent to the outgoing waves, except when the disturbance source was close to a boundary. The time-domain data generated by such CAA solutions were often intractable until their spectra was analyzed. Therefore, the relative merits of three different methods were included in the study. For simple, periodic waves, the periodogram method produced better estimates of the steep-sloped spectra than the Blackman-Tukey method. Also, for this problem, the Hanning window was more effective when used with the weighted-overlapped-segment-averaging and Blackman-Tukey methods gave better results than the periodogram method. Finally, it was demonstrated that the representation of time domain-data was significantly dependent on the particular spectral analysis method employed.

  16. Investigation of Improved Methods in Power Transfer Efficiency for Radiating Near-Field Wireless Power Transfer

    Directory of Open Access Journals (Sweden)

    Hesheng Cheng

    2016-01-01

    Full Text Available A metamaterial-inspired efficient electrically small antenna is proposed, firstly. And then several improving power transfer efficiency (PTE methods for wireless power transfer (WPT systems composed of the proposed antenna in the radiating near-field region are investigated. Method one is using a proposed antenna as a power retriever. This WPT system consisted of three proposed antennas: a transmitter, a receiver, and a retriever. The system is fed by only one power source. At a fixed distance from receiver to transmitter, the distance between the transmitter and the retriever is turned to maximize power transfer from the transmitter to the receiver. Method two is using two proposed antennas as transmitters and one antenna as receiver. The receiver is placed between the two transmitters. In this system, two power sources are used to feed the two transmitters, respectively. By adjusting the phase difference between the two feeding sources, the maximum PTE can be obtained at the optimal phase difference. Using the same configuration as method two, method three, where the maximum PTE can be increased by regulating the voltage (or power ratio of the two feeding sources, is proposed. In addition, we combine the proposed methods to construct another two schemes, which improve the PTE at different extent than classical WPT system.

  17. Oxide properties of autoclaved zircaloy cladding tubes investigated by the photoelectric polarization method

    International Nuclear Information System (INIS)

    Nystrand, A.C.

    2000-06-01

    Corrosion of zirconium alloys is an important lifetime limiting factor for the nuclear reactor fuel. The corrosion resistance of a metal is highly dependent on the ability of the surface metal oxide to transport electrons and ions, which is related to the stoichiometry of the oxide and the oxide defect concentration. The Photoelectric Polarization Method (PEP) is a structure sensitive method which earlier has been investigated as a possible method to study the defect structure in zirconium oxides. The purpose of the following work is, by using more optimized experimental equipment, to verify if the PEP method is a suitable method to study the defect structure in zirconium oxides and to predict the corrosion resistance for different zirconium alloys. The conclusions from the experiments are as follows: - The modifications of the experimental setup by means of a new source of light (deuterium lamp) and a new oscilloscope with an amplifier gave distinct Vpep signals. - The photoresponse is negative for all types of cladding and under all kind of oxidation regimes and hence the oxide is a n-type semiconductor with deficiency of oxygen. - The method needs to be verified by testing semiconductors with a known defect concentration

  18. Investigation of RNA Structure by High-Throughput SHAPE-Based Probing Methods

    DEFF Research Database (Denmark)

    Poulsen, Line Dahl

    of highthroughput SHAPE-based approaches to investigate RNA structure based on novel SHAPE reagents that permit selection of full-length cDNAs. The SHAPE Selection (SHAPES) method is applied to the foot-and-mouth disease virus (FMDV) plus strand RNA genome, and the data is used to construct a genome-wide structural...... that they are functional. The SHAPES method is further applied to the hepatitis C virus (HCV), where the data is used to refine known and predicted structures. Over the past years, the interest of studying RNA structure in their native environment has been increased, and to allow studying RNA structure inside living cells...... using the SHAPE Selection approach, I introduce a biotinylated probing reagent. This chemical can cross cell membranes and reacts with RNA inside the cells, allowing the structural conformations to be studied in the context of physiological relevant conditions in living cells. The methods and results...

  19. Investigating the performance of directional boundary layer model through staged modeling method

    Science.gov (United States)

    Jeong, Moon-Gyu; Lee, Won-Chan; Yang, Seung-Hune; Jang, Sung-Hoon; Shim, Seong-Bo; Kim, Young-Chang; Suh, Chun-Suk; Choi, Seong-Woon; Kim, Young-Hee

    2011-04-01

    Generally speaking, the models used in the optical proximity effect correction (OPC) can be divided into three parts, mask part, optic part, and resist part. For the excellent quality of the OPC model, each part has to be described by the first principles. However, OPC model can't take the all of the principles since it should cover the full chip level calculation during the correction. Moreover, the calculation has to be done iteratively during the correction until the cost function we want to minimize converges. Normally the optic part in OPC model is described with the sum of coherent system (SOCS[1]) method. Thanks to this method we can calculate the aerial image so fast without the significant loss of accuracy. As for the resist part, the first principle is too complex to implement in detail, so it is normally expressed in a simple way, such as the approximation of the first principles, and the linear combinations of factors which is highly correlated with the chemistries in the resist. The quality of this kind of the resist model depends on how well we train the model through fitting to the empirical data. The most popular way of making the mask function is based on the Kirchhoff's thin mask approximation. This method works well when the feature size on the mask is sufficiently large, but as the line width of the semiconductor circuit becomes smaller, this method causes significant error due to the mask topography effect. To consider the mask topography effect accurately, we have to use rigorous methods of calculating the mask function, such as finite difference time domain (FDTD[2]) and rigorous coupled-wave analysis (RCWA[3]). But these methods are too time-consuming to be used as a part of the OPC model. Until now many alternatives have been suggested as the efficient way of considering the mask topography effect. Among them we focused on the boundary layer model (BLM) in this paper. We mainly investigated the way of optimization of the parameters for the

  20. An automatic method to generate domain-specific investigator networks using PubMed abstracts

    Directory of Open Access Journals (Sweden)

    Gwinn Marta

    2007-06-01

    Full Text Available Abstract Background Collaboration among investigators has become critical to scientific research. This includes ad hoc collaboration established through personal contacts as well as formal consortia established by funding agencies. Continued growth in online resources for scientific research and communication has promoted the development of highly networked research communities. Extending these networks globally requires identifying additional investigators in a given domain, profiling their research interests, and collecting current contact information. We present a novel strategy for building investigator networks dynamically and producing detailed investigator profiles using data available in PubMed abstracts. Results We developed a novel strategy to obtain detailed investigator information by automatically parsing the affiliation string in PubMed records. We illustrated the results by using a published literature database in human genome epidemiology (HuGE Pub Lit as a test case. Our parsing strategy extracted country information from 92.1% of the affiliation strings in a random sample of PubMed records and in 97.0% of HuGE records, with accuracies of 94.0% and 91.0%, respectively. Institution information was parsed from 91.3% of the general PubMed records (accuracy 86.8% and from 94.2% of HuGE PubMed records (accuracy 87.0. We demonstrated the application of our approach to dynamic creation of investigator networks by creating a prototype information system containing a large database of PubMed abstracts relevant to human genome epidemiology (HuGE Pub Lit, indexed using PubMed medical subject headings converted to Unified Medical Language System concepts. Our method was able to identify 70–90% of the investigators/collaborators in three different human genetics fields; it also successfully identified 9 of 10 genetics investigators within the PREBIC network, an existing preterm birth research network. Conclusion We successfully created a

  1. An automatic method to generate domain-specific investigator networks using PubMed abstracts

    Science.gov (United States)

    Yu, Wei; Yesupriya, Ajay; Wulf, Anja; Qu, Junfeng; Gwinn, Marta; Khoury, Muin J

    2007-01-01

    Background Collaboration among investigators has become critical to scientific research. This includes ad hoc collaboration established through personal contacts as well as formal consortia established by funding agencies. Continued growth in online resources for scientific research and communication has promoted the development of highly networked research communities. Extending these networks globally requires identifying additional investigators in a given domain, profiling their research interests, and collecting current contact information. We present a novel strategy for building investigator networks dynamically and producing detailed investigator profiles using data available in PubMed abstracts. Results We developed a novel strategy to obtain detailed investigator information by automatically parsing the affiliation string in PubMed records. We illustrated the results by using a published literature database in human genome epidemiology (HuGE Pub Lit) as a test case. Our parsing strategy extracted country information from 92.1% of the affiliation strings in a random sample of PubMed records and in 97.0% of HuGE records, with accuracies of 94.0% and 91.0%, respectively. Institution information was parsed from 91.3% of the general PubMed records (accuracy 86.8%) and from 94.2% of HuGE PubMed records (accuracy 87.0). We demonstrated the application of our approach to dynamic creation of investigator networks by creating a prototype information system containing a large database of PubMed abstracts relevant to human genome epidemiology (HuGE Pub Lit), indexed using PubMed medical subject headings converted to Unified Medical Language System concepts. Our method was able to identify 70–90% of the investigators/collaborators in three different human genetics fields; it also successfully identified 9 of 10 genetics investigators within the PREBIC network, an existing preterm birth research network. Conclusion We successfully created a web-based prototype

  2. Development of the numerical method for liquid metal magnetohydrodynamics (I). Investigation of the method and development of the 2D method

    International Nuclear Information System (INIS)

    Ohira, H.; Ara, K.

    2002-11-01

    Advanced electromagnetic components are investigated in Feasibility Studies on Commercialized FR Cycle System to apply to the main cooling systems of Liquid Metal Fast Reactor. Although a lot of experiments and numerical analysis were carried out on both high Reynolds numbers and high magnetic Reynolds numbers, the complex phenomena could not be evaluated in detail. As the first step of the development of the numerical methods for the liquid metal magnetohydrodynamics, we investigated numerical methods that could be applied to the electromagnetic components with both complex structures and high magnetic turbulent field. As a result, we selected GSMAC (Generalized-Simplified MArker and Cell) method for calculating the liquid metal fluid dynamics because it could be easily applied to the complex flow field. We also selected the vector-FEM for calculating the magnetic field of the large components because the method had no interaction procedure. In the high magnetic turbulent field, the dynamic-SGS models would be also a promising model for the good estimation, because it could calculate the field directly without any experimental constant. In order to verify the GSMAC and the vector-FEM, we developed the 2D numerical models and calculated the magnetohydrodynamics in the large electromagnetic pump. It was estimated from these results that the methods were basically reasonable, because the calculated pressure differences had the similar tendencies to the experimental ones. (author)

  3. Measurement methods of physical activity in investigation associated with assessment of quality of life in elder adults

    Directory of Open Access Journals (Sweden)

    Kurysh N.O.

    2012-02-01

    Full Text Available Analysis of publication in physical activity measurement methods is provided. Presented three groups of physical activity measurement methods criterion, objective, subjective methods. Established that criterion methods are more accurate and used for validate objective and subjective methods. Subjective methods frequently used in investigation of youth and elderly population. Advisability of IPAQ questionnaire in international physical activity investigation of elderly adults is substantiated.

  4. Experimental and Theoretical Structural Investigation of AuPt Nanoparticles Synthesized Using a Direct Electrochemical Method.

    Science.gov (United States)

    Lapp, Aliya S; Duan, Zhiyao; Marcella, Nicholas; Luo, Long; Genc, Arda; Ringnalda, Jan; Frenkel, Anatoly I; Henkelman, Graeme; Crooks, Richard M

    2018-05-11

    In this report, we examine the structure of bimetallic nanomaterials prepared by an electrochemical approach known as hydride-terminated (HT) electrodeposition. It has been shown previously that this method can lead to deposition of a single Pt monolayer on bulk-phase Au surfaces. Specifically, under appropriate electrochemical conditions and using a solution containing PtCl 4 2- , a monolayer of Pt atoms electrodeposits onto bulk-phase Au immediately followed by a monolayer of H atoms. The H atom capping layer prevents deposition of Pt multilayers. We applied this method to ∼1.6 nm Au nanoparticles (AuNPs) immobilized on an inert electrode surface. In contrast to the well-defined, segregated Au/Pt structure of the bulk-phase surface, we observe that HT electrodeposition leads to the formation of AuPt quasi-random alloy NPs rather than the core@shell structure anticipated from earlier reports relating to deposition onto bulk phases. The results provide a good example of how the phase behavior of macro materials does not always translate to the nano world. A key component of this study was the structure determination of the AuPt NPs, which required a combination of electrochemical methods, electron microscopy, X-ray absorption spectroscopy, and theory (DFT and MD).

  5. Valence and lowest Rydberg electronic states of phenol investigated by synchrotron radiation and theoretical methods

    Energy Technology Data Exchange (ETDEWEB)

    Limão-Vieira, P., E-mail: plimaovieira@fct.unl.pt; Ferreira da Silva, F.; Lange, E. [Laboratório de Colisões Atómicas e Moleculares, CEFITEC, Departamento de Física, Faculdade de Ciências e Tecnologia, Universidade NOVA de Lisboa, 2829-516 Caparica (Portugal); Duflot, D. [Univ. Lille, UMR 8523–Physique des Lasers Atomes et Molécules, F-59000 Lille (France); CNRS, UMR 8523, F-59000 Lille (France); Jones, N. C.; Hoffmann, S. V. [ISA, Department of Physics and Astronomy, Aarhus University, Ny Munkegade 120, DK-8000 Aarhus C (Denmark); Śmiałek, M. A. [Department of Control and Power Engineering, Faculty of Ocean Engineering and Ship Technology, Gdańsk University of Technology, Gabriela Narutowicza 11/12, 80-233 Gdańsk (Poland); Department of Physical Sciences, The Open University, Walton Hall, MK7 6AA Milton Keynes (United Kingdom); Jones, D. B. [School of Chemical and Physical Sciences, Flinders University, GPO Box 2100, Adelaide, SA 5001 (Australia); Brunger, M. J. [School of Chemical and Physical Sciences, Flinders University, GPO Box 2100, Adelaide, SA 5001 (Australia); Institute of Mathematical Sciences, University of Malaya, 50603 Kuala Lumpur (Malaysia)

    2016-07-21

    We present the experimental high-resolution vacuum ultraviolet (VUV) photoabsorption spectra of phenol covering for the first time the full 4.3–10.8 eV energy-range, with absolute cross sections determined. Theoretical calculations on the vertical excitation energies and oscillator strengths were performed using time-dependent density functional theory and the equation-of-motion coupled cluster method restricted to single and double excitations level. These have been used in the assignment of valence and Rydberg transitions of the phenol molecule. The VUV spectrum reveals several new features not previously reported in the literature, with particular reference to the 6.401 eV transition, which is here assigned to the 3sσ/σ{sup ∗}(OH)←3π(3a″) transition. The measured absolute photoabsorption cross sections have been used to calculate the photolysis lifetime of phenol in the earth’s atmosphere (0–50 km).

  6. Experimental investigation of radiation effect on human thermal comfort by Taguchi method

    International Nuclear Information System (INIS)

    Arslanoglu, Nurullah; Yigit, Abdulvahap

    2016-01-01

    Highlights: • Radiation heat flux from lighting lamps on human thermal comfort is studied. • The effect of posture position on thermal comfort is investigated. • The effect of clothing color on thermal comfort is examined. • Radiation heat flux from halogen reflector lamp increase skin temperature more. • Posture position effect on thermal comfort is less than the other parameters. - Abstract: In this study, the effect of radiation heat flux of lighting lamps on human thermal comfort was investigated by using Taguchi method. In addition, at indoor conditions, clothing color and posture position under the radiation effect on thermal comfort were also investigated. For this purpose, experiments were performed in an air conditioned laboratory room in summer and autumn seasons. The amount of temperature rise on the back was considered as performance parameter. An L8 orthogonal array was selected as an experimental plan for the third parameters mentioned above for summer and autumn seasons. The results were analyzed for the optimum conditions using signal-to-noise (S/N) ratio and ANOVA method. The optimum results were found to be clear halogen lamp as lighting lamp, white as t-shirt color, standing as posture position, in summer season. The optimum levels of the lighting lamp, t-shirt color and posture position were found to be clear halogen lamp, white, sitting in autumn season, respectively.

  7. Numerical investigations on applicability of permanent magnet method to crack detection in HTS film

    Energy Technology Data Exchange (ETDEWEB)

    Kamitani, A., E-mail: kamitani@yz.yamagata-u.ac.jp [Yamagata University, 4-3-16, Johnan, Yonezawa, Yamagata 992-8510 (Japan); Takayama, T. [Yamagata University, 4-3-16, Johnan, Yonezawa, Yamagata 992-8510 (Japan); Saitoh, A. [University of Hyogo, 2167, Shosha, Himeji, Hyogo 671-2280 (Japan)

    2014-09-15

    Highlights: • The defect parameter is defined for characterizing a crack position. • The defect parameter shows a remarkable change only near a crack. • A crack detection method is proposed on the basis of the permanent-magnet method. • The high-speed rough detection can be achieved by means of the proposed method. - Abstract: The scanning permanent-magnet (PM) method was originally developed for determining the spatial distribution of the critical current density in a high-temperature superconducting (HTS) film. In the present study, its applicability to the crack detection in an HTS film is investigated numerically. To this end, a defect parameter is defined for characterizing a crack position and it is calculated along various scanning lines. The results of computations show that, only when the scanning position is near a crack, the defect parameter shows a violent change. On the basis of the behavior of the defect parameter, the method for roughly identifying a crack is also proposed.

  8. Numerical investigations on applicability of permanent magnet method to crack detection in HTS film

    International Nuclear Information System (INIS)

    Kamitani, A.; Takayama, T.; Saitoh, A.

    2014-01-01

    Highlights: • The defect parameter is defined for characterizing a crack position. • The defect parameter shows a remarkable change only near a crack. • A crack detection method is proposed on the basis of the permanent-magnet method. • The high-speed rough detection can be achieved by means of the proposed method. - Abstract: The scanning permanent-magnet (PM) method was originally developed for determining the spatial distribution of the critical current density in a high-temperature superconducting (HTS) film. In the present study, its applicability to the crack detection in an HTS film is investigated numerically. To this end, a defect parameter is defined for characterizing a crack position and it is calculated along various scanning lines. The results of computations show that, only when the scanning position is near a crack, the defect parameter shows a violent change. On the basis of the behavior of the defect parameter, the method for roughly identifying a crack is also proposed

  9. Modern contact investigation methods for enhancing tuberculosis control in Aboriginal communities

    Directory of Open Access Journals (Sweden)

    Victoria J. Cook

    2012-05-01

    Full Text Available The Aboriginal communities in Canada are challenged by a disproportionate burden of TB infection and disease. Contact investigation (CI guidelines exist but these strategies do not take into account the unique social structure of different populations. Because of the limitations of traditional CI, new approaches are under investigation and include the use of social network analysis, geographic information systems and genomics, in addition to the widespread use of genotyping to better understand TB transmission. Guidelines for the routine use of network methods and other novel methodologies for TB CI and outbreak investigation do not exist despite the gathering evidence that these approaches can positively impact TB control efforts, even in Aboriginal communities. The feasibility and efficacy of these novel approaches to CI in Aboriginal communities requires further investigation. The successful integration of these novel methodologies will require community involvement, capacity building and ongoing support at every level. The outcome will not only be the systematic collection, analysis, and interpretation of CI data in high-burden communities to assess transmission but the prioritization of contacts who are candidates for treatment of LTBI which will break the cycle of transmission. Ultimately, the measure of success will be a clear and sustained decline in TB incidence in Aboriginal communities.

  10. Investigating flow patterns in a channel with complex obstacles using the lattice Boltzmann method

    Energy Technology Data Exchange (ETDEWEB)

    Yojina, Jiraporn; Ngamsaad, Waipot; Nuttavut, Narin; Triampo, Darapond; Lenbury, Yongwimon; Sriyab, Somchai; Triampo, Wannapong [Faculty of Science, Mahidol University, Bangkok (Thailand); Kanthang, Paisan [Rajamangala University of Technology, Bangkok (Thailand)

    2010-10-15

    In this work, mesoscopic modeling via a computational lattice Boltzmann method (LBM) is used to investigate the flow pattern phenomena and the physical properties of the flow field around one and two square obstacles inside a two-dimensional channel with a fixed blockage ratio,{beta} =14 , centered inside a 2D channel, for a range of Reynolds numbers (Re) from 1 to 300. The simulation results show that flow patterns can initially exhibit laminar flow at low Re and then make a transition to periodic, unsteady, and, finally, turbulent flow as the Re get higher. Streamlines and velocity profiles and a vortex shedding pattern are observed. The Strouhal numbers are calculated to characterize the shedding frequency and flow dynamics. The effect of the layouts or configurations of the obstacles are also investigated, and the possible connection between the mixing process and the appropriate design of a chemical mixing system is discussed

  11. Neurocognitive Poetics: methods and models for investigating the neuronal and cognitive- affective bases of literature reception

    Directory of Open Access Journals (Sweden)

    Arthur M Jacobs

    2015-04-01

    Full Text Available A long tradition of research including classical rhetoric, aesthetics and poetics theory, formalism and structuralism, as well as current perspectives in (neurocognitive poetics has investigated structural and functional aspects of literature reception. Despite a wealth of literature published in specialised journals like Poetics, however, still little is known about how the brain processes and creates literary and poetic texts. Still, such stimulus material might be suited better than other genres for demonstrating the complexities with which our brain constructs the world in and around us, because it unifies thought and language, music and imagery in a clear, manageable way, most often with play, pleasure, and emotion (Schrott & Jacobs, 2011. In this paper, I discuss methods and models for investigating the neuronal and cognitive-affective bases of literary reading together with pertinent results from studies on poetics, text processing, emotion, or neuroaesthetics, and outline current challenges and future perspectives.

  12. A method for radiobiological investigations in radiation fields with different LET and high dose rates

    International Nuclear Information System (INIS)

    Grundler, W.

    1976-01-01

    For investigations: 1. Performed in the field of radiobiology with different LET-radiation and a relatively high background dose rate of one component (e.g. investigations with fast and intermediate reactor neutrons) 2. Concerning radiation risk studies within a wide range 3. Of irradiations, covering a long time period (up to 100 days) a test system is necessary which on the one hand makes it possible to analyze the influence of different LET radiation and secondly shows a relative radiation resistant behaviour and allows a simple cell cycle regulation. A survey is given upon the installed device of a simple cell observation method, the biological test system used and the analysis of effects caused by dose, repair and LET. It is possible to analyze the behaviour of the nonsurvival cells and to demonstrate different reactions of the test parameters to the radiation of different LET. (author)

  13. Investigation Of Interaction Between Nitinol Stent And A Vascular Plaque Using Finite Element Method

    Directory of Open Access Journals (Sweden)

    Recep Güneş

    2012-06-01

    Full Text Available In this study, the interaction between the Nitinol stent and the artery with plaque was investigated using finite element method. The occurring pressure values during the cardiac contraction (systolic and loosening (diastolic were applied as loading to the modeled system with Nitinol stent. In the light of the stress values, the suitability of the Nitinol stent in an artery with plaque was investigated. In the analysis, Nitinol stent was assumed to be shape memory alloy, and artery and plaque were assumed to behave linearly elastic. As a result, the stress and deformations in the plaque and artery due to the interference of Nitinol stent were discussed and concluded that the structure of artery with plaque can be expanded in accordance with Nitinol stent.

  14. Practical investigation of a monopod fabrication method and the numerical investigation of its up-righting process

    Directory of Open Access Journals (Sweden)

    Khaled A. Hafez

    2013-09-01

    Full Text Available The principal purpose of this paper is to present a novel two phases rational scenario applied in constructing an offshore monopod platform; in which the two phases are the all-ground horizontal construction phase and the post-construction phase. Concerning the all-ground construction phase, a brief investigation of its different stages, i.e., pre-fabrication, fabrication, pre-assembling, positioning, assembling, and surface finishing is introduced. The important practical aspects of such construction phase are investigated without going into the nitty-gritty of the details involved therein. Concerning the post-construction phase, a clear investigation of its sequential stages, i.e., lifting, moving and up-righting is introduced. A finite element model (FEM of the monopod platform is created to perform the structural analysis necessary to decide the suspension points/devices and the handling scenario during the various stages of the post-construction phase on a rational wise. Such structural analysis is performed within the framework of the three dimensional quasi-static modeling and analysis aiming at simulating the realistic handling condition, and hence introducing a reliable physical interpretation of the numerical results. For the whole effort to be demonstrated efficiently, the results obtained are analyzed, the conclusions are presented, and few related recommendations are suggested.

  15. Employment of a novel ultrasonic method to investigate high pressure phase transitions in oleic acid

    Science.gov (United States)

    Rostocki, A. J.; Siegoczyński, R. M.; Kiełczyński, P.; Szalewski, M.; Balcerzak, A.; Zduniak, M.

    2011-06-01

    In this work, the variation of sound velocity with hydrostatic pressure for oleic acid is evaluated up to 350 MPa. During the measurement, we identified the phase transformation of oleic acid and the presence of the hysteresis of the dependence of sound velocity on pressure. From the performed measurements, it can be seen that the dependence of sound velocity on pressure can be used to investigate phase transformations in natural oils. Ultrasonic waves were excited and detected using piezoelectric LiNbO3(Y-36 cut) 5 MHz transducers. The phase velocity of the longitudinal ultrasonic waves was measured using a cross-correlation method to evaluate the time of flight.

  16. Thermalization calorimetry: A simple method for investigating glass transition and crystallization of supercooled liquids

    DEFF Research Database (Denmark)

    Jakobsen, Bo; Sanz, Alejandro; Niss, Kristine

    2016-01-01

    and their crystallization, e.g., for locating the glass transition and melting point(s), as well as for investigating the stability against crystallization and estimating the relative change in specific heat between the solid and liquid phases at the glass transition......We present a simple method for fast and cheap thermal analysis on supercooled glass-forming liquids. This “Thermalization Calorimetry” technique is based on monitoring the temperature and its rate of change during heating or cooling of a sample for which the thermal power input comes from heat...

  17. Transition processes in the novel method of the muon catalysis investigation

    International Nuclear Information System (INIS)

    Filchenkov, V.V.

    1997-01-01

    The problem of modifying the interpretation of the results to be obtained with the novel method of muon catalysis investigation to take the fast transition processes into account is first considered. The results of exploring the process kinetics are compared with the ones found from the analysis of the appropriate Monte Carlo distributions. The calculation programs simulate both the kinetics and the registration system of the experiment which is now performed in the frame of the large international project TRITON. The main conclusion is that the multiplicity distribution of the fusion neutrons is 'invariant' under any assumptions of the fast transition stage

  18. Investigation of the stability of blocks around underground openings by using the boundary element method

    Directory of Open Access Journals (Sweden)

    Murat Ünal

    2002-03-01

    Full Text Available In this study, a two-dimensional software was developed by using the boundary element method, in order to model and solve the rock mechanics problems encountered in surface and underground excavations. Stability of rock wedges formed at the roof of underground excavations were investigated in detail by using this software. The behaviour of the symmetric wedge on different joint stiffnesses was studied using a modified boundary element software. Then the results obtained were discussed and compared with the analytical solution, considering the surface tractions, shear stresses (developed along the discontinuity, wedge displacements and strains (along the wedge height.

  19. Investigations in the problem of pion condensation using generator co-ordinate methods

    International Nuclear Information System (INIS)

    Chattopadhyay, P.; Providencia, J. da

    1981-01-01

    Pion condensation in neutron matter has been investigated using the generator coordinate methode and a simple p-wave interaction. The assumption of a condensed mode corresponding to one pion momentum (determined variationally) helps evaluate all the necessary matrix elements exactly. The technique of charge projection from a coherent state of negative pions is discussed, and calculations have been carried out for the cases of average charge conversation, charge projection before variation and for a charge conserving trial function. The ground-state energies and the lowest excitations of the system are obtained from numerical solutions of the Hill-Wheeler equation. (orig.)

  20. Investigation of the cluster formation in lithium niobate crystals by computer modeling method

    Energy Technology Data Exchange (ETDEWEB)

    Voskresenskii, V. M.; Starodub, O. R., E-mail: ol-star@mail.ru; Sidorov, N. V.; Palatnikov, M. N. [Russian Academy of Sciences, Tananaev Institute of Chemistry and Technology of Rare Earth Elements and Mineral Raw Materials, Kola Science Centre (Russian Federation)

    2017-03-15

    The processes occurring upon the formation of energetically equilibrium oxygen-octahedral clusters in the ferroelectric phase of a stoichiometric lithium niobate (LiNbO{sub 3}) crystal have been investigated by the computer modeling method within the semiclassical atomistic model. An energetically favorable cluster size (at which a structure similar to that of a congruent crystal is organized) is shown to exist. A stoichiometric cluster cannot exist because of the electroneutrality loss. The most energetically favorable cluster is that with a Li/Nb ratio of about 0.945, a value close to the lithium-to-niobium ratio for a congruent crystal.

  1. Investigation of the crystallization process of titanium alloy ingots produced by vacuum arc melting method

    International Nuclear Information System (INIS)

    Tetyukhin, V.V.; Kurapov, V.N.; Trubin, A.N.; Demchenko, M.V.; Lazarev, V.G.; Ponedilko, S.V.; Dubrovina, N.T.; Kurapova, L.A.

    1978-01-01

    The process of crystallization and hardening of the VT3-1 and VT9 titanium alloys ingots during the vacuum-arc remelting (VAR) has been studied. In order to investigate the kinetics of the hole shape changing and the peculiarities of the ingot formation during the VAR, the radiography method has been used. It is established that the VAR of the titanium alloy ingots is basically a continuous process. An intense heating of the liquid bath mirror and the availability of high temperature gradients in the hole are the typical features of the VAR process

  2. INSTRUMENTS AND METHODS OF INVESTIGATION: Positron annihilation spectroscopy in materials structure studies

    Science.gov (United States)

    Grafutin, Viktor I.; Prokop'ev, Evgenii P.

    2002-01-01

    A relatively new method of materials structure analysis — positron annihilation spectroscopy (PAS) — is reviewed. Measurements of positron lifetimes, the determination of positron 3γ- and 2γ-annihilation probabilities, and an investigation of the effects of different external factors on the fundamental characteristics of annihilation constitute the basis for this promising method. The ways in which the positron annihilation process operates in ionic crystals, semiconductors, metals and some condensed matter systems are analyzed. The scope of PAS is described and its prospects for the study of the electronic and defect structures are discussed. The applications of positron annihilation spectroscopy in radiation physics and chemistry of various substances as well as in physics and chemistry of solutions are exemplified.

  3. Investigation of an Autofocusing Method for Visible Aerial Cameras Based on Image Processing Techniques

    Directory of Open Access Journals (Sweden)

    Zhichao Chen

    2016-01-01

    Full Text Available In order to realize the autofocusing in aerial camera, an autofocusing system is established and its characteristics such as working principle and optical-mechanical structure and focus evaluation function are investigated. The reason for defocusing in aviation camera is analyzed and several autofocusing methods along with appropriate focus evaluation functions are introduced based on the image processing techniques. The proposed autofocusing system is designed and implemented using two CMOS detectors. The experiment results showed that the proposed method met the aviation camera focusing accuracy requirement, and a maximum focusing error of less than half of the focus depth is achieved. The system designed in this paper can find the optical imaging focal plane in real-time; as such, this novel design has great potential in practical engineering, especially aerospace applications.

  4. A simple method for the investigation of the high temperature plasticity of metallic materials

    Energy Technology Data Exchange (ETDEWEB)

    Chinh, N.Q. (Inst. for General Physics, Lorand Eoetvoes Univ., Budapest (Hungary)); Juhasz, A. (Inst. for General Physics, Lorand Eoetvoes Univ., Budapest (Hungary)); Tasnadi, P. (Inst. for General Physics, Lorand Eoetvoes Univ., Budapest (Hungary)); Kovacs, I. (Inst. for General Physics, Lorand Eoetvoes Univ., Budapest (Hungary))

    1993-11-01

    The indentation creep test is a powerful and quick method for the investigation of the high temperature plasticity of various materials. During creep test a small cylindrical punch is pressed at constant loads into the surface of the sample and the penetration depth is registered as a function of testing time. On the basis of the creep curves taken at various temperatures and loads the strain rate sensitivity and the activation energy of the steady-state creep process can be determined. The main advantage of this test is that it needs only a small amount of testing material. In this paper the usefullness of this method illustrated by some results obtained on superplastic and non superplastic Al alloys. The indentation results are compared with tensile data obtained on the same materials. (orig.).

  5. Investigation of bacterial adherence to a non-precious alloy with radiolabeling method

    International Nuclear Information System (INIS)

    Sonugelen, M.; Iyiyapici Destan, U.; Oeztuerk, B.; Yurt Lambrecht, F.

    2006-01-01

    The objective of this study was to investigate the bacterial adherence to a non-precious alloy with radiolabeling method. S. mutans, E. coliand C. albicanswere labeled with 99m Tc by using stannous chloride and their radiolabeling yields were calculated. After the labeling procedure, metal disks (3 mm x 10 mm) were treated with microorganisms. The amount of labeled microorganisms adhered on metal surfaces was determined by activity measurements. The labeling yields for S. mutans, E. coliand C. albicanswere 69.95 ± 7.58%, 78.84 ± 0.44% and 79.71 ± 10.17%, respectively. The mean values for adherence for S. mutans, E. coliand C. albicans on metal samples were 7.02 ± 2.18%, 0.96 ± 0.49% and 8.80 ± 8.24%, respectively. The radiolabeling method could be considered as safe and precise for determining the adherence of microorganisms. (author)

  6. Investigation on human serum albumin and Gum Tragacanth interactions using experimental and computational methods.

    Science.gov (United States)

    Moradi, Sajad; Taran, Mojtaba; Shahlaei, Mohsen

    2018-02-01

    The study on the interaction of human serum albumin and Gum Tragacanth, a biodegradable bio-polymer, has been undertaken. For this purpose, several experimental and computational methods were used. Investigation of thermodynamic parameters and mode of interactions were carried out using Fluorescence spectroscopy in 300 and 310K. Also, a Fourier transformed infrared spectra and synchronous fluorescence spectroscopy was performed. To give detailed insight of possible interactions, docking and molecular dynamic simulations were also applied. Results show that the interaction is based on hydrogen bonding and van der Waals forces. Structural analysis implies on no adverse change in protein conformation during binding of GT. Furthermore, computational methods confirm some evidence on secondary structure enhancement of protein as a presence of combining with Gum Tragacanth. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. Investigating the Effectiveness of Teaching Methods Based on a Four-Step Constructivist Strategy

    Science.gov (United States)

    Çalik, Muammer; Ayas, Alipaşa; Coll, Richard K.

    2010-02-01

    This paper reports on an investigation of the effectiveness an intervention using several different methods for teaching solution chemistry. The teaching strategy comprised a four-step approach derived from a constructivist view of learning. A sample consisting of 44 students (18 boys and 26 girls) was selected purposively from two different Grade 9 classes in the city of Trabzon, Turkey. Data collection employed a purpose-designed `solution chemistry concept test', consisting of 17 items, with the quantitative data from the survey supported by qualitative interview data. The findings suggest that using different methods embedded within the four-step constructivist-based teaching strategy enables students to refute some alternative conceptions, but does not completely eliminate student alternative conceptions for solution chemistry.

  8. [Bioinorganic chemical composition of the lens and methods of its investigation].

    Science.gov (United States)

    Avetisov, S E; Novikov, I A; Pakhomova, N A; Motalov, V G

    2018-01-01

    Bioinorganic chemical composition of the lens of human and experimental animals (cows, dogs, rats, rabbits) have been analyzed in various studies. In most cases, the studies employed different methods to determine the gross (total) composition of chemical elements and their concentrations in the examined samples. Less frequently, they included an assessment of the distribution of chemical elements in the lens and correlation of their concentration with its morphological changes. Chemical elements from all groups (series) of the periodic classification system were discovered in the lens substance. Despite similar investigation methods, different authors obtained contradicting results on the chemical composition of the lens. This article presents data suggesting possible correlation between inorganic chemical elements in the lens substance with the development and formation of lenticular opacities. All currently employed methods are known to only analyze limited number of select chemical elements in the tissues and do not consider the whole range of elements that can be analyzed with existing technology; furthermore, the majority of studies are conducted on the animal model lens. Therefore, it is feasible to continue the development of the chemical microanalysis method by increasing the sensitivity of Scanning Electron Microscopy with Energy Dispersive Spectroscopy (SEM/EDS) with the purpose of assessing the gross chemical composition and distribution of the elements in the lens substance, as well as revealing possible correlation between element concentration and morphological changes in the lens.

  9. Investigation of spatial correlation in MR images of human cerebral white matter using geostatistical methods

    International Nuclear Information System (INIS)

    Keil, Fabian

    2014-01-01

    Investigating the structure of human cerebral white matter is gaining interest in the neurological as well as in the neuroscientific community. It has been demonstrated in many studies that white matter is a very dynamic structure, rather than a static construct which does not change for a lifetime. That means, structural changes within white matter can be observed even on short timescales, e.g. in the course of normal ageing, neurodegenerative diseases or even during learning processes. To investigate these changes, one method of choice is the texture analysis of images obtained from white matter. In this regard, MRI plays a distinguished role as it provides a completely non-invasive way of acquiring in vivo images of human white matter. This thesis adapted a statistical texture analysis method, known as variography, to quantify the spatial correlation of human cerebral white matter based on MR images. This method, originally introduced in geoscience, relies on the idea of spatial correlation in geological phenomena: in naturally grown structures near things are correlated stronger to each other than distant things. This work reveals that the geological principle of spatial correlation can be applied to MR images of human cerebral white matter and proves that variography is an adequate method to quantify alterations therein. Since the process of MRI data acquisition is completely different to the measuring process used to quantify geological phenomena, the variographic analysis had to be adapted carefully to MR methods in order to provide a correctly working methodology. Therefore, theoretical considerations were evaluated with numerical samples in a first, and validated with real measurements in a second step. It was shown that MR variography facilitates to reduce the information stored in the texture of a white matter image to a few highly significant parameters, thereby quantifying heterogeneity and spatial correlation distance with an accuracy better than 5

  10. Investigation of spatial correlation in MR images of human cerebral white matter using geostatistical methods

    Energy Technology Data Exchange (ETDEWEB)

    Keil, Fabian

    2014-03-20

    Investigating the structure of human cerebral white matter is gaining interest in the neurological as well as in the neuroscientific community. It has been demonstrated in many studies that white matter is a very dynamic structure, rather than a static construct which does not change for a lifetime. That means, structural changes within white matter can be observed even on short timescales, e.g. in the course of normal ageing, neurodegenerative diseases or even during learning processes. To investigate these changes, one method of choice is the texture analysis of images obtained from white matter. In this regard, MRI plays a distinguished role as it provides a completely non-invasive way of acquiring in vivo images of human white matter. This thesis adapted a statistical texture analysis method, known as variography, to quantify the spatial correlation of human cerebral white matter based on MR images. This method, originally introduced in geoscience, relies on the idea of spatial correlation in geological phenomena: in naturally grown structures near things are correlated stronger to each other than distant things. This work reveals that the geological principle of spatial correlation can be applied to MR images of human cerebral white matter and proves that variography is an adequate method to quantify alterations therein. Since the process of MRI data acquisition is completely different to the measuring process used to quantify geological phenomena, the variographic analysis had to be adapted carefully to MR methods in order to provide a correctly working methodology. Therefore, theoretical considerations were evaluated with numerical samples in a first, and validated with real measurements in a second step. It was shown that MR variography facilitates to reduce the information stored in the texture of a white matter image to a few highly significant parameters, thereby quantifying heterogeneity and spatial correlation distance with an accuracy better than 5

  11. Tools of Thor - more than a hammer: An overview of some analysis methods for turbulence investigation

    Science.gov (United States)

    Haaland, Stein; Vaivads, Andris; Eriksson, Elin

    2016-04-01

    In the old Norse mythology Thor was a hammer-wielding god associated with thunder and lightning. THOR is also an acronym for Turbulence Heating ObserveR - a planned space mission dedicated to stydy space plasma turbulence. Whereas the mythological Thor did most of his work with a single tool, Mjølnir - his hammer, the modern version of THOR is far more versatile. The proposed THOR spacecraft comes with a comprehensive package of instruments to explore the energy dissipation and particle energization taking place in turbulent plasma environments. This paper presents a more detailed investigation of some of the analysis methods listed in the submitted THOR proposal. To demonstrate the methods, we have used data from existing spacecraft missions like Cluster and MMS to examine and compare single-spacecraft and multi-spacecraft methods to establish proper frames. The presented analysis methods are based on fundamental plasma laws, such as conservation of mass, momentum and energy and do not require any triangulation or gradients based on multiple spacecraft. Our experience based on Cluster and MMS results show that a well equipped single spacecraft platform, like the proposed THOR mission, very often provides better and less ambiguous results that a constellation of many spacecraft with less capable instrumentation. Limitations in underlying assumptions, such as planarity and linearity, as well as non-optimal spacecraft separation and configurations often limit the possibility to utilize multi-spacecraft methods. We also investigate the role of time resolution and dynamical range of the measurements used in the methods. Since the particle instruments onboard THOR will have a much better time resolution than existing magnetospheric satellite missions, we infer that THOR will be far better suited to resolve time evolution in plasma structures. This is of particular importance in the solar wind and magnetosheat, where frame velocities can be very high. With a larger

  12. Use of the potentiometric titration method to investigate heterogeneous systems including phosphorylated complexones

    International Nuclear Information System (INIS)

    Tereshin, G.S.; Kharitonova, L.K.; Kuznetsova, O.B.

    1979-01-01

    Heterogeneous systems Y(NO 3 ) 3 (YCl 3 )-Hsub(n)L-KNO 3 (KCl)-H 2 O are investigated by potentiometric titration (with coulomb-meter generation of oH - ions). Hsub(n)L is one of the following: oxyethylidendiphosphonic; aminobenzilidendiphosphonic; glycine-bis-methyl-phosphonic; nitrilotrimethylphosphonic (H 6 L) and ethylenediaminetetramethylphosphonic acids. The range of the exsistence of YHsub(nL3)LxyH 2 O has been determined. The possibility of using potentiometric titration for investigating heterogeneous systems is demonstrated by the stUdy of the system Y(NO 3 ) 3 -H 6 L-KOH-H 2 o by the method of residual concentration. The two methods have shown that at pH 3 LxyH 2 O; at pH=6, KYH 2 Lxy'H 2 O, and at pH=7, K 2 YHLxy''H 2 O. The complete solubility products of nitrilotrimethylphosphonates are evaluated

  13. Method for investigating management impact to causes and consequences of specific hazards MIMIX

    Energy Technology Data Exchange (ETDEWEB)

    Heikkilae, J; Rouhiainen, V; Suokas, J [VTT Manufacturing Technology, Tampere (Finland). Safety Engineering; Rasmussen, B [Risoe National Lab., Roskilde (Denmark)

    1996-12-31

    Method for Investigating Management Impact to Causes and Consequences of Specific Hazards (MIMIX) is a new method for the identification of deficiencies in managerial means and practices used for maintaining and improving safety in a plant. MIMIX is a part of TOMHID methodology which is aimed for overall identification of hazards in a chemical plant. However, MIMIX can be used independently. This report includes guidelines for carrying out a MIMIX analysis. Some experiences from TOMHID analysis case studies, forms and other supporting material (appendix A) and an example of the preparation of incident scenarios (appendix B) are also included in the report. MIMIX consists of three main stages: preparation of incident scenarios, worker interviews and management interviews. A couple of incident scenarios are prepared to support the worker interviews. In each worker interview, such undesired conditions in the plant which promote errors and violations affecting the incident described in a scenario are identified. Deficiencies in managerial means and practices used for correcting the identified undesired conditions are investigated with management interviews. (author)

  14. Method for investigating management impact to causes and consequences of specific hazards MIMIX

    Energy Technology Data Exchange (ETDEWEB)

    Heikkilae, J.; Rouhiainen, V.; Suokas, J. [VTT Manufacturing Technology, Tampere (Finland). Safety Engineering; Rasmussen, B. [Risoe National Lab., Roskilde (Denmark)

    1995-12-31

    Method for Investigating Management Impact to Causes and Consequences of Specific Hazards (MIMIX) is a new method for the identification of deficiencies in managerial means and practices used for maintaining and improving safety in a plant. MIMIX is a part of TOMHID methodology which is aimed for overall identification of hazards in a chemical plant. However, MIMIX can be used independently. This report includes guidelines for carrying out a MIMIX analysis. Some experiences from TOMHID analysis case studies, forms and other supporting material (appendix A) and an example of the preparation of incident scenarios (appendix B) are also included in the report. MIMIX consists of three main stages: preparation of incident scenarios, worker interviews and management interviews. A couple of incident scenarios are prepared to support the worker interviews. In each worker interview, such undesired conditions in the plant which promote errors and violations affecting the incident described in a scenario are identified. Deficiencies in managerial means and practices used for correcting the identified undesired conditions are investigated with management interviews. (author)

  15. Isotopic methods of investigations of hydrodynamics in installations for hydrometallurgic processing of copper concentrates

    International Nuclear Information System (INIS)

    Stsheletski, M.; Urban'ski, T.S.

    1979-01-01

    Isotope methods have been presented of investigations of hydrodynamics of liquid and solid phases in pilot-scale installations for hydrometallurgic processing of copper concentrates: in the column installation for leaching; in the tubular reactor for copper reduction by hydrogen and in the installation for crystallization of magnesium sulphate under pressure conditions. The column leaching installation has been tested by pulse injection of two radioisotope indicators simultaneously. The copper concentrate was labelled by sorbed colloidal gold-198 and the liquid phase was labelled by solution of sodium chloride containing sodium-24. Measurements of the radiation intensities were registered by scintillation counters, working with a single-channel amplitude analyzer, integrators and counting rate monitors. According to the distribution of time of stay, by the moments method, number of powers of ideal intermixings in the cell model of flow of the both phases. In the tubular reactor process of copper reduction by hydrogen is going on in three phases: gas-liquid-solig phase. Hydrodynamic investigations in this instalation was done in the presence of air, water and copper powder. Water was labelled by sodium-24 and copper powder by copper-64. Changes of intensity of radiation were measured by scintillation counters, located along the installation and were registered by multichannel amplitude analyzer. Peckle number and longitudal dispersion factor were determined. In investigations of the solid phase hydrodynamics during crystallization of magnesium sulphate under elevated temperature and high pressure, as an indicator, isotope gold-198 has been used, by which crystalls of the solid phase were labelled, and isotope sodium-24 was added to a liquid. Simultaneousely were measured and registered by a single-channel analyzer intensity of radiation of both indicators. Mean time of stay and parameters of a mathematical model of the phases flow in this installation were

  16. A numerical method for investigating crystal settling in convecting magma chambers

    Science.gov (United States)

    Verhoeven, J.; Schmalzl, J.

    2009-12-01

    Magma chambers can be considered as thermochemically driven convection systems. We present a new numerical method that describes the movement of crystallized minerals in terms of active spherical particles in a convecting magma that is represented by an infinite Prandtl number fluid. The main part focuses on the results we obtained. A finite volume thermochemical convection model for two and three dimensions and a discrete element method, which is used to model granular material, are combined. The new model is validated with floating experiments using particles of different densities and an investigation of single and multiparticle settling velocities. The resulting velocities are compared with theoretical predictions by Stokes's law and a hindered settling function for the multiparticle system. Two fundamental convection regimes are identified in the parameter space that is spanned by the Rayleigh number and the chemical Rayleigh number, which is a measure for the density of the particles. We define the T regime that is dominated by thermal convection. Here the thermal driving force is strong enough to keep all particles in suspension. As the particles get denser, they start settling to the ground, which results in a C regime. The C regime is characterized by the existence of a sediment layer with particle-rich material and a suspension layer with few particles. It is shown that the presence of particles can reduce the vigor of thermal convection. In the frame of a parameter study we discuss the change between the regimes that is systematically investigated. We show that the so-called TC transition fits a power law. Furthermore, we investigate the settling behavior of the particles in vigorous thermal convection, which can be linked to crystal settling in magma chambers. We develop an analytical settling law that describes the number of settled particles against time and show that the results fit the observations from numerical and laboratory experiments.

  17. Improving safety culture in hospitals: Facilitators and barriers to implementation of Systemic Falls Investigative Method (SFIM).

    Science.gov (United States)

    Zecevic, Aleksandra A; Li, Alvin Ho-Ting; Ngo, Charity; Halligan, Michelle; Kothari, Anita

    2017-06-01

    The purpose of this study was to assess the facilitators and barriers to implementation of the Systemic Falls Investigative Method (SFIM) on selected hospital units. A cross-sectional explanatory mixed methods design was used to converge results from a standardized safety culture survey with themes that emerged from interviews and focus groups. Findings were organized by six elements of the Ottawa Model of Research Use framework. A geriatric rehabilitation unit of an acute care hospital and a neurological unit of a rehabilitation hospital were selected purposefully due to the high frequency of falls. Hospital staff who took part in: surveys (n = 39), interviews (n = 10) and focus groups (n = 12), and 38 people who were interviewed during falls investigations: fallers, family, unit staff and hospital management. Implementation of the SFIM to investigate fall occurrences. Percent of positive responses on the Modified Stanford Patient Safety Culture Survey Instrument converged with qualitative themes on facilitators and barriers for intervention implementation. Both hospital units had an overall poor safety culture which hindered intervention implementation. Facilitators were hospital accreditation, strong emphasis on patient safety, infrastructure and dedicated champions. Barriers included heavy workloads, lack of time, lack of resources and poor communication. Successful implementation of SFIM requires regulatory and organizational support, committed frontline staff and allocation of resources to identify active causes and latent contributing factors to falls. System-wide adjustments show promise for promotion of safety culture in hospitals where falls happen regularly. © The Author 2017. Published by Oxford University Press in association with the International Society for Quality in Health Care. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

  18. Investigation and application of reduced-order methods for flows study in heat exchanger tube bundles

    International Nuclear Information System (INIS)

    Pomarede, M.

    2012-01-01

    The objective of this thesis is to study the ability of model reduction for investigations of flow-induced vibrations in heat exchangers tube bundle systems.These mechanisms are a cause of major concern because heat exchangers are key elements of nuclear power plants and on-board stoke-holds.In a first part, we give a recall on heat exchangers functioning and on vibratory problems to which they are prone. Then, complete calculations leaded with the CFD numerical code Code-Saturne are carried out, first for the flow around a single circular cylinder (fixed then elastically mounted) and then for the case of a tube bundle system submitted to cross-flow. Reduced-order method POD is applied to the flow resolution with fixed structures. The obtained results show the efficiency of this technique for such configurations, using stabilization methods for the dynamical system resolution in the tube-bundle case. Multiphase-POD, which is a method enabling the adaptation of POD to fluid-structure interactions, is applied. Large displacements of a single cylinder elastically mounted under cross-flow, corresponding to the lock-in phenomenon,are well reproduced with this reduction technique. In the same way, large displacements of a confined moving tube in a bundle are shown to be faithfully reconstructed.Finally, the use of model reduction is extended to parametric studies. First, we propose to use the method which consists in projecting Navier-Stokes equations for several values of the Reynolds number on to a unique POD basis. The results obtained confirm the fact that POD predictability is limited to a range of parameter values. Then, a basis interpolation method, constructed using Grassmann manifolds and allowing the construction of a POD basis from other pre-calculated basis, is applied to basic cases. (author)

  19. From blackbirds to black holes: Investigating capture-recapture methods for time domain astronomy

    Science.gov (United States)

    Laycock, Silas G. T.

    2017-07-01

    In time domain astronomy, recurrent transients present a special problem: how to infer total populations from limited observations. Monitoring observations may give a biassed view of the underlying population due to limitations on observing time, visibility and instrumental sensitivity. A similar problem exists in the life sciences, where animal populations (such as migratory birds) or disease prevalence, must be estimated from sparse and incomplete data. The class of methods termed Capture-Recapture is used to reconstruct population estimates from time-series records of encounters with the study population. This paper investigates the performance of Capture-Recapture methods in astronomy via a series of numerical simulations. The Blackbirds code simulates monitoring of populations of transients, in this case accreting binary stars (neutron star or black hole accreting from a stellar companion) under a range of observing strategies. We first generate realistic light-curves for populations of binaries with contrasting orbital period distributions. These models are then randomly sampled at observing cadences typical of existing and planned monitoring surveys. The classical capture-recapture methods, Lincoln-Peterson, Schnabel estimators, related techniques, and newer methods implemented in the Rcapture package are compared. A general exponential model based on the radioactive decay law is introduced which is demonstrated to recover (at 95% confidence) the underlying population abundance and duty cycle, in a fraction of the observing visits (10-50%) required to discover all the sources in the simulation. Capture-Recapture is a promising addition to the toolbox of time domain astronomy, and methods implemented in R by the biostats community can be readily called from within python.

  20. Investigation of potential analytical methods for redox control of the vitrification process

    International Nuclear Information System (INIS)

    Goldman, D.S.

    1985-11-01

    An investigation was conducted to evaluate several analytical techniques to measure ferrous/ferric ratios in simulated and radioactive nuclear waste glasses for eventual redox control of the vitrification process. Redox control will minimize the melt foaming that occurs under highly oxidizing conditions and the metal precipitation that occurs under highly reducing conditions. The analytical method selected must have a rapid response for production problems with minimal complexity and analyst involvement. The wet-chemistry, Moessbauer spectroscopy, glass color analysis, and ion chromatography techniques were explored, with particular emphasis being placed on the Moessbauer technique. In general, all of these methods can be used for nonradioactive samples. The Moessbauer method can readily analyze glasses containing uranium and thorium. A shielded container was designed and built to analyze fully radioactive glasses with the Moessbauer spectrometer in a hot cell environment. However, analyses conducted with radioactive waste glasses containing 90 Sr and 137 Cs were unsuccessful, presumably due to background radiation problems caused by the samples. The color of glass powder can be used to analyze the ferrous/ferric ratio for low chromium glasses, but this method may not be as precise as the others. Ion chromatography was only tested on nonradioactive glasses, but this technique appears to have the required precision due to its analysis of both Fe +2 and Fe +3 and its anticipated adaptability for radioactivity samples. This development would be similar to procedures already in use for shielded inductively coupled plasma emission (ICP) spectrometry. Development of the ion chromatography method is therefore recommended; conventional wet-chemistry is recommended as a backup procedure

  1. Collection and analysis of existing information on applicability of investigation methods for characterizing natural events/processes in a coastal region

    International Nuclear Information System (INIS)

    Nakayasu, Akio; Niizato, Tadafumi; Yasue, Ken-ichi; Doke, Ryosuke; Shigehiro, Michiko; Tanaka, Takenobu; Aoki, Michinori; Sekiya, Ayako

    2011-02-01

    The investigation methods for characterizing natural events and processes in a coastal field have been extracted on the basis of analysis of previous research. Collected information is classified into three groups according to the characteristics of natural events/processes and investigation methods. First group is the methods for evaluation of uplift, subsidence and sedimentation rates. Second group is the methods for evaluation of denudation rates. The third group is the methods for reconstruction of the climatic and sea-level changes. Study area, timeframe of the investigation, work sequences, techniques for age-determination, index and objects for characterizing natural events/processes, etc. in each research example were arranged in an 'information spread sheet'. Information on applicability of the each investigation method was extracted from information spread sheet, and was arranged in tabular form. Based on an analysis of the above information, investigation method that can be applied to a coastal region was extracted. The methods and indices are as follows: Uplift rate: the heights of marine terraces are the most important index in an upheaval region. Subsidence and sedimentation rate: the depths of strata underlying an alluvial plain are main indices in a subsidence region. Denudation rate: the features of marine terrace are main indices and the inspection of denudation processes by the use of a numerical simulation is necessary. Climate change: lacustrine deposits are main object for investigation. Sea-level change: reconstruction of relative sea-level change curve including uplift/subsidence factor and paleogeography based on acoustic exploration and the investigation of marine terraces. (author)

  2. Investigation on welding and cutting methods for blanket support legs of fusion experimental reactors

    International Nuclear Information System (INIS)

    Tokami, Ikuhide; Nakahira, Masataka; Kurasawa, Toshimasa; Sato, Satoshi; Furuya, Kazuyuki; Hatano, Toshihisa; Takatsu, Hideyuki; Kuroda, Toshimasa.

    1996-07-01

    A toroidally-and poloidally-divided modular blanket has been proposed for a fusion experimental reactor, such as ITER, to enhance its maintainability as well as improve its fabricability. The blanket module, typically the size of 1 m wide, 1-2 m high and 0.4 m deep and the weight of 4 ton, will be supported by support legs which are extruded from back of the module and connected to a 70-100 mm thick strong back plate. The support leg has to withstand large electromagnetic force during plasma disruption and provide the way for in-situ module replacement by remote handling. For the connection method of the support leg to the back plate, a welding approach has been investigated here in terms of its high reliability against the large electromagnetic loads. For the welding approach, the support leg needs to be 70 mm thick, and the working space for welding/cutting heads are limited to 100 mm x 150 mm adjacent to the support leg. Based on a comparison of several welding methods, e.g. NGTIG, NGMIG and laser, NGTIG has been selected as a reference due to its well-established technology and the least R and D required. As for the cutting method, a plasma cutting has been given the highest priority to be pursued because of its compactness and high speed. Through preliminary design studies, the possibility of small welding/cutting heads that will work in the limited space has been shown, and maintenance route for in-situ module replacement with pre-and postfixture of the module has been investigated. Also preliminary R and Ds have resulted in; 1)the welding distortion is predictable according to the shape of weld groove and adjustable to meet the placement requirement of the module first wall, 2)the plasma cut surface can be rewelded without machining, 3)the welding/cutting time will meet the requirement of maintenance time. (author)

  3. Electrical investigations of hybrid OLED microcavity structures with novel encapsulation methods

    Science.gov (United States)

    Meister, Stefan; Brückner, Robert; Fröb, Hartmut; Leo, Karl

    2016-04-01

    An electrical driven organic solid state laser is a very challenging goal which is so far well beyond reach. As a step towards realization, we monolithically implemented an Organic Light Emitting Diode (OLED) into a dielectric, high quality microcavity (MC) consisting of two Distributed Bragg Reectors (DBR). In order to account for an optimal optical operation, the OLED structure has to be adapted. Furthermore, we aim to excite the device not only electrically but optically as well. Different OLED structures with an emission layer consisting of Alq3:DCM (2 wt%) were investigated. The External Quantum Efficiencies (EQE) of this hybrid structures are in the range of 1-2 %, as expected for this material combination. Including metal layers into a MC is complicated and has a huge impact on the device performance. Using Transfer-Matrix-Algorithm (TMA) simulations, the best positions for the metal electrodes are determined. First, the electroluminescence (EL) of the adjusted OLED structure on top of a DBR is measured under nitrogen atmosphere. The modes showed quality factors of Q = 60. After the deposition of the top DBR, the EL is measured again and the quality factors increased up to Q = 600. Considering the two 25-nm-thick-silver contacts a Q-factor of 600 is very high. The realization of a suitable encapsulation method is important. Two approaches were successfully tested. The first method is based on the substitution of a DBR layer with a layer produced via Atomic Layer Deposition (ALD). The second method uses a 0.15-mm-thick cover glass glued on top of the DBR with a 0.23-μm-thick single-component glue layer. Due to the working encapsulation, it is possible to investigate the sample under ambient conditions.

  4. New methods for the investigation of phase objects by digital Speckle-pattern-interferometry

    International Nuclear Information System (INIS)

    Fliesser, W.

    1996-11-01

    This work shows new possibilities for spatially resolved interferometric investigations of transparent objects (phase-objects) applying the method of Digital-Speckle-Pattern-Interferometry (DSPI). A feedback-system using an additional MICHELSON-interferometer in the reference-arm of the Speckle-interferometer was installed for computer-controlled digitalization of the primary interferograms at defined phase-shifts. A special program for interferogram analysis allows the evaluation of two-dimensional phase distributions using different phase-stepping algorithms as 3-Frame-, 4-Frame-, CARRE-, 4+1-Frame- and 6+1-Frame technique. Special DSPI-setups with modified MACH-ZEHNDER-interferometers were used to check the system. In some basic experiments the temperature distribution in a cross section of convective heat-flows of air was measured. As an application on plasma-diagnostics the space-resolved electron density in a high pressure mercury lamp was determined using two-wavelength-DSPI. To increase the sensitivity of the method a Nd-YAG-laser at 1064 nm was employed in addition to an Ar + -laser at 488 Nm. The electron density in one cross-section of the lamp could be calculated by ABEL-inversion of the measured phase data. A multi-directional optical setup with a special mirror system was developed to investigate asymmetric phase-objects by DSPI. The setup allows to store six primary interferograms from different directions in one step, while using a single reference-beam only. Helium flows in air with different flow geometries were used as phase-objects. Tomographic reconstruction procedures such as the convolution-method yield the distributions of the refractive-index and the related helium concentrations in selected cross sections of the flow. (author)

  5. Investigation of effective forensic cleaning methods for bullet and cartridge case samples

    Science.gov (United States)

    Shuherk, Cassie Marie

    Bullet and cartridge case evidence may potentially link weapons and crimes through the comparison of toolmark patterns. This analysis relies on the clarity of the toolmarks and the ability of the examiner to identify patterns on the evidence. These patterns may be distorted by debris such as soil, blood, cyanoacrylate, and construction materials. Despite the potential importance of bullet and cartridge case evidence, few investigations of proper cleaning methods have been conducted. The present study was designed to examine the effects of various cleaning solutions and application methods on copper and brass bullets and cartridge cases. Additionally, this research investigated the efficacy of these cleaning protocols on the common evidence contaminants blood and cyanoacrylate. No cleaning method was found to be universally effective on both contaminant types and nondestructive to the metal surface. Ultrasonication was the most efficient application method employed when used in conjunction with an appropriate cleaning solution. Acetone proved to be safe and successful at removing heavy cyanoacrylate deposits from brass cartridge cases without damaging the metal. Although sulfuric acid removed most of the cyanoacrylate from the brass cartridge case, ultrasonication of the fumed cartridge cases in sulfuric acid caused the nickel-plated primer caps to turn black. Additionally, etching occurred when sulfuric acid was allowed to dry on the cartridge case surface. Citric acid, salt-flour-vinegar paste, TergazymeRTM, and water did not effectively remove the cyanoacrylate from the cartridge cases, but the solutions were safe to use on the brass and sometimes resulted in a shinier surface. Regardless of the cleaning method employed, the bloodstained bullets retained most or all of the underlying brown tarnish. Ultrasonication with sulfuric acid was successful at removing some blood-initiated tarnishing; however, the removal of residues was not complete, making it difficult

  6. Investigation of the Optimal Parameters in Hydrothermal Method for the Synthesis of ZnO Nanorods

    Directory of Open Access Journals (Sweden)

    Ying-Chung Chen

    2014-01-01

    Full Text Available We investigated a two-step method to deposit the ZnO-based nanostructure films, including nanorods and nanoflowers. In the first step, sputtering method was used to deposit the ZnO films on SiO2/Si substrates as the seed layer. In the second step, Zn(NO32–6H2O and C6H12N4 were used as precursors and hydrothermal process was used as the method to synthesize the ZnO films. After that, the ZnO films were measured by an X-ray diffraction pattern and a FESEM to analyze their crystallization and morphology. We had found that the ZnO films had three different morphologies synthesized on ZnO/SiO2/Si substrates, including irregular-plate structure films, nanorod films, and beautiful chrysanthemum-like clusters (nanoflower films. We would prove that the face direction of ZnO/SiO2/Si substrates in the hydrothermal bottle and deposition time were two important factors to influence the synthesized results of the ZnO films.

  7. Investigation of new NMR methods for structural and dynamic studies in the liquid state

    International Nuclear Information System (INIS)

    Desvaux, H.

    1993-01-01

    After a short presentation of the NMR fundements, three new methods of spin -lattice relaxation in liquids are reported. (1) The method consists of measuring the steady-state nuclear magnetization under strong off-resonance rf irradiation as a function of the angle θ between external field and effective field. For purely dipolar relaxation between homonuclear spins under isotropic Brownian molecular rotation, this variation yields the value of the local correlation time. A departure from the theoretical shape reveals the existence of complex motions or complex relaxation mechanisms. These results have been verified by experimental illustrations. Some numerical simulations have been performed for studying the effects of the distribution of chemical shift and for studying the coherence of the local correlation time concept. (2) The improvements of a modified ROESY experiment are discussed. The use of a time-modulated strong off-resonances rf irradiation permits to suppress totally the problems of the NOESY (suppression of cross-relaxation peaks for molecules where ωτ c ≅ 1.1) and of the ROESY (HOHAHA transfer and angular dispersion due to the chemical shift distribution). The angle θ defined previously can be used as a constraint: either to obtain a ratio of the cross over direct dipolar relaxation rates independent on the correlation time value, or to observe the sole chemical exchange. (3) The difference of the relaxation rates of the coherences at zero and two quanta is always exactly the cross relaxation rates measured by the NOESY experiment. The experimental illustration is presented

  8. Investigation and Optimization of Blade Tip Winglets Using an Implicit Free Wake Vortex Method

    Science.gov (United States)

    Lawton, Stephen; Crawford, Curran

    2014-06-01

    Novel outer-blade geometries such as tip winglets can increase the aerodynamic power that can be extracted from the wind by tailoring the relative position and strengths of trailed vorticity. This design space is explored using both parameter studies and gradient-based optimization, with the aerodynamic analysis carried out using LibAero, a free wake vortex-based code introduced in previous work. The starting design is the NREL 5MW reference turbine, which allows comparison of the aerodynamic simulation for the unmodified blade with other codes. The code uses a Prandtl-Weissinger lifting line model to represent the blade, and vortex filaments as the flow elements. A fast multipole method is implemented to accelerate the influence calculations and reduce the computational cost. This results in higher fidelity aerodynamic simulations that can capture the effects of novel geometries while maintaining sufficiently fast run-times (on the order of an hour) to allow the use of optimization. Gradients of the objective function with respect to design variables are calculated using the complex step method which is accurate and efficient. Since the vortex structure behind the rotor is being resolved in detail, insight is also gained into the mechanisms by which these new blade designs affect performance. It is found that adding winglets can increase the power extracted from the wind by around 2%, with a similar increase in thrust. It is also possible to create a winglet that slightly lowers the thrust while maintaining very similar power compared to the standard straight blade.

  9. Investigation and Optimization of Blade Tip Winglets Using an Implicit Free Wake Vortex Method

    International Nuclear Information System (INIS)

    Lawton, Stephen; Crawford, Curran

    2014-01-01

    Novel outer-blade geometries such as tip winglets can increase the aerodynamic power that can be extracted from the wind by tailoring the relative position and strengths of trailed vorticity. This design space is explored using both parameter studies and gradient-based optimization, with the aerodynamic analysis carried out using LibAero, a free wake vortex-based code introduced in previous work. The starting design is the NREL 5MW reference turbine, which allows comparison of the aerodynamic simulation for the unmodified blade with other codes. The code uses a Prandtl-Weissinger lifting line model to represent the blade, and vortex filaments as the flow elements. A fast multipole method is implemented to accelerate the influence calculations and reduce the computational cost. This results in higher fidelity aerodynamic simulations that can capture the effects of novel geometries while maintaining sufficiently fast run-times (on the order of an hour) to allow the use of optimization. Gradients of the objective function with respect to design variables are calculated using the complex step method which is accurate and efficient. Since the vortex structure behind the rotor is being resolved in detail, insight is also gained into the mechanisms by which these new blade designs affect performance. It is found that adding winglets can increase the power extracted from the wind by around 2%, with a similar increase in thrust. It is also possible to create a winglet that slightly lowers the thrust while maintaining very similar power compared to the standard straight blade

  10. Multi-method chronological investigation of a Middle Paleolithic stratigraphic context in Eastern Transylvania, Romania

    Science.gov (United States)

    Veres, Daniel; Cosac, Marian; Muratoreanu, George; Niţǎ, Loredana; Schmidt, Christoph; Hambach, Ulrich; Hubay, Katalin; Alexandru, Radu; Cuculici, Roxana; Lucian Buzea, Dan; Dumitraşcu, Valentin

    2016-04-01

    The Middle to Upper Paleolithic transition is one of the crucial periods of change in the prehistory of Europe due to the full emergence, continent-wide, of modern human technologies, detrimental of Neanderthal survival. Knowledge about the transition is vast, however, the evidence for cultural and technological developments in the Carpathian - Lower Danube area is still rather sparse. Here we discuss latest results arising from an archaeological-chronological investigation of a Middle Paleolithic context within the Varghis karst, eastern Transylvania, Romania. Combining our results with these of previous excavations, we can distinguish several stages of habitation in the area comprising a rock shelter connected to a newly discovered filled-in cave entrance. Reanalysis of the deeper stratigraphy previously unexcavated shows that at least two main habitation levels have been preserved. In both levels, the bone assemblages (Bos/Bison, Capra, Canis lupus, Ursus spaeleus) directly associated with lithics point to human-accumulation of material. In order to augment the typological cultural considerations, we applied direct radiocarbon dating on bones from within the occupation layers and on scattered charcoal, for the latter following a two-step combustion protocol (1). Radiocarbon dating on bones suggests the lowermost occupation layer is >43.4 radiocarbon kyr BP old, whereas the preliminary infrared stimulated luminescence (IRSL) ages on the lowermost productive layer and above it indicate surprisingly old ages of ca. 120 kyr and respectively, ca. 70 kyr. Multiple-protocol dating of charcoal found within the two habitation layers produced ages >38 radiocarbon kyr BP, suggesting that the lowermost habitation layer unequivocally pertains to the Middle Paleolithic industries. For the upper productive layer, radiocarbon dating of charcoal found 20 cm above it produced a surprisingly young age of 17.4 radiocarbon kyr BP. However, as the carbon content of this sample was

  11. A further investigation of the centroid-to-centroid method for stereotactic lung radiotherapy: A phantom study

    International Nuclear Information System (INIS)

    Lu, Bo; Samant, Sanjiv; Mittauer, Kathryn; Lee, Soyoung; Huang, Yin; Li, Jonathan; Kahler, Darren; Liu, Chihray

    2013-01-01

    Purpose: Our previous study [B. Lu et al., “A patient alignment solution for lung SBRT setups based on a deformable registration technique,” Med. Phys. 39(12), 7379–7389 (2012)] proposed a deformable-registration-based patient setup strategy called the centroid-to-centroid (CTC) method, which can perform an accurate alignment of internal-target-volume (ITV) centroids between averaged four-dimensional computed tomography and cone-beam computed tomography (CBCT) images. Scenarios with variations between CBCT and simulation CT caused by irregular breathing and/or tumor change were not specifically considered in the patient study [B. Lu et al., “A patient alignment solution for lung SBRT setups based on a deformable registration technique,” Med. Phys. 39(12), 7379–7389 (2012)] due to the lack of both a sufficiently large patient data sample and a method of tumor tracking. The aim of this study is to thoroughly investigate and compare the impacts of breathing pattern and tumor change on both the CTC and the translation-only (T-only) gray-value mode strategies by employing a four-dimensional (4D) lung phantom.Methods: A sophisticated anthropomorphic 4D phantom (CIRS Dynamic Thorax Phantom model 008) was employed to simulate all desired respiratory variations. The variation scenarios were classified into four groups: inspiration to expiration ratio (IE ratio) change, tumor trajectory change, tumor position change, tumor size change, and the combination of these changes. For each category the authors designed several scenarios to demonstrate the effects of different levels of breathing variation on both of the T-only and the CTC methods. Each scenario utilized 4DCT and CBCT scans. The ITV centroid alignment discrepancies for CTC and T-only were evaluated. The dose-volume-histograms (DVHs) of ITVs for two extreme cases were analyzed.Results: Except for some extreme cases in the combined group, the accuracy of the CTC registration was about 2 mm for all cases for

  12. Investigation of innovative radiation imaging method and system for radiological environments

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, H. [School of Biomedical Engineering, Korea University, Seoul (Korea, Republic of); Joung, J., E-mail: jinhun.joung@nucaremed.com [School of Biomedical Engineering, Korea University, Seoul (Korea, Republic of); Nucare, Inc., Incheon (Korea, Republic of); Kim, Y. [School of Biomedical Engineering, Korea University, Seoul (Korea, Republic of); Nucare, Inc., Incheon (Korea, Republic of); Lee, K. [School of Biomedical Engineering, Korea University, Seoul (Korea, Republic of)

    2017-03-01

    We have developed a novel imaging method that can be applied to most applications in the field of radiological environment imaging. It resolves either two-dimensional (2D) or three-dimensional (3D) distributions of radioactive sources in applications for homeland security, environmental monitoring, radiation contamination monitoring, baggage inspection, nuclear power plant monitoring, and more. The proposed imaging method uses a simple detector configured as a radiation-counting detector with spectroscopic capabilities. The detector module consists of two components: a flat field-of-view (FOV) collimator with a 30° FOV opening and a typical single-channel radiation detector made of a 2 in.×2 in. NaI(Tl) scintillator coupled to a 2 in photomultiplier tube (PMT). This simple detector module makes it possible to develop a cost-effective imaging system and provide design freedom in extending the system configuration to include one-dimensional (1D) or 2D detector-array shapes to meet the needs of various applications. One of most distinctive features of the new imaging method is that it uses only a pair of 2D projections to obtain a 3D reconstruction. The projections are measured by the proposed detector module at two positions orthogonal to one another; the measured projections are manipulated to enhance the resolution of the reconstructed 3D image. The imaging method comprises several steps performed consecutively: projection measurement, energy re-binning, projection separation, resolution and attenuation recovery, image reconstruction, and image consolidation and quantitative analysis. The resolution and attenuation recovery step provides the most distinctive and important processing by which the poor quality of projection data is enhanced. Such poor quality is mainly due to the use of a simple detector with a wide-opening flat FOV collimator. Simulation and experimental studies have been conducted to validate the proposed method. In this investigation, we

  13. A method to investigate the biomechanical alterations in Perthes’ disease by hip joint contact modeling

    DEFF Research Database (Denmark)

    Salmingo, Remel A.; Skytte, Tina Lercke; Traberg, Marie Sand

    2017-01-01

    for the preoperative planning to obtain stress relief for the highly stressed areas in the malformed hip. This single-patient study demonstrated that the biomechanical alterations in Perthes’ disease can be evaluated individually by patient-specific finite element contact modeling using MRI. A multi-patient study...... was to develop a method to investigate the biomechanical alterations in Perthes’ disease by finite element (FE ) contact modeling using MRI. The MRI data of a unilateral Perthes’ case was obtained to develop the three-dimensional FE model of the hip joint. The stress and contact pressure patterns...... in the unaffected hip were well distrib uted. Elevated concentrations of stress and contact pressure were found in the Perthes’ hip. The highest femoral cartilagev on Mises stress 3.9 MPa and contact pressure 5.3 M P a were found in the Perthes’ hip, whereas 2.4 M P a and 4.9 MP a in the healthy hip, respectively...

  14. Neutron autoradiography: working-out method and application in investigations of test paintings

    International Nuclear Information System (INIS)

    Kalicki, A.; Panczyk, E.; Rowinska, L.; Sartowska, B.; Walis, L.; Pytel, K.; Pytel, B.; Koziel, A.; Dabkowski, L.; Wierzchnicka, M.; Strzalkowski, L.; Ostrowski, T.

    2001-01-01

    Neutron-induced autoradiography was carried out at MARIA research reactor in Poland. The paintings were exposed to the thermal neutrons. As a result, the radionuclides emitting beta particles and gamma rays were created from some of the elements existing in the painting. Beta particles were detected during successive exposure to a series of X-ray medical-sensitive films. The obtained images--blackening of the films depends mainly on the nuclear characteristic of recorded radionuclides and exposure parameters. The main purpose of this work was to work out a method, build a special stand and test sample paintings using neutron autoradiography. Samples of paintings were investigated and according to the obtained results, optimum test parameters have been selected: neutron irradiation conditions and autoradiographs exposure conditions

  15. Investigation of impurity defects in α-iron by molecular dynamics method

    International Nuclear Information System (INIS)

    Kevorkyan, Yu.R.

    1986-01-01

    Investigation of the configuration of impurity defects in α-iron by the molecular dynamics method is presented. The Jhonson model potential has been used to calculate the interaction of matrix atoms. The impurity-matrix atom interaction is described by the same form of the potential shifted along the axis of interatomic distances for a definite value. The correspondence between the shift value and change in the radius of the impurity defect is established on the basis of calculation of the relaxation volume. Possible configurations of the impurity - interstitial matrix atom complexes are obtained for the given model of the impurity defect, dimensional boundaries of possible transitions between different configurations are determined. Formation and bound energies, relaxation volumes of impurity defects are calculated

  16. Investigation for calculation methods used in analyzing the physics characteristics of nuclear power reactor

    International Nuclear Information System (INIS)

    Nguyen Tuan Khai; Hoang Van Khanh; Phan Quoc Vuong; Tran Viet Phu; Tran Vinh Thanh; Nguyen Thi Mai Huong; Nguyen Thi Dung; Le Tran Chung; Nguyen Minh Tuan; Tran Quoc Duong

    2014-01-01

    The project aims at nuclear human resource development and enhancement in research capability in reactor physics and kinetics at Nuclear Energy Center (Institute for Nuclear Science and Technology) and Nuclear Reactor Center (Nuclear Research Institute, Dalat). The main research items of the project can be summarized as follows: i) Considering possibility on using modern calculation techniques and methods in investigating neutronic characteristics and neutronics-thermal hydraulics coupling. This item is proposed to carry out based on international collaboration with Prof. Le Trong Thuy, San Jose University, US; ii) Carrying out the collaborative activities in research and training between Nuclear Energy Center (Institute for Nuclear Science and Technology) and Nuclear Reactor Center (Nuclear Research Institute, Dalat); iii) Opening two-week training course on nuclear reactor engineering (25 Nov - 12 Dec 2013) in collaboration with Japan Atomic Energy Agency (JAEA). (author)

  17. Investigation methods for the determination of thermodynamic properties of lithium alloys

    International Nuclear Information System (INIS)

    Sommer, F.

    1981-01-01

    For the determination of thermodynamic properties of the highly reactive lithium alloys, during the last years a number of measuring methods, especially apt for the investigation of these systems, have been developed. The most important measuring arrangements are presented in regard to their manner of function and their technical applicability for the measurements. Among these devices are high temperature calorimeters for the determination of mixing enthalpies of liquid alloys, whilst the formation enthalpies of intermetallic compounds can be determined using a suitable solution calorimeter. Heat contents measurements using a drop calorimeter are resulting in the determination of specific heats, of the enthalpy of fusion and of the temperature dependence of the mixing enthalpy. The Gibbs free enthalpy of mixing of lithium alloys can successfully be determined using suitable galvanic cells. (orig.)

  18. An investigation of the element composition of superconducting ceramics by neutron activation and radiography methods

    International Nuclear Information System (INIS)

    Kist, A.A.; Flitsiyan, E.S.

    1994-01-01

    The neutron activation methods for determining the general composition and distribution of the main components in HTSC ceramics were developed. The conditions for the reduction of the analysis error were discussed. The dependences of the oxygen content and superconducting parameters of single-phase and polyphase yttrium ceramics on the regime of heat treatment in air were investigated. Variation in the oxygen content was found to have a nonmonotone character, depending on the temperature of quenching and annealing. Correlation between the character of the superconducting transition and the oxygen content was observed. During the heat treatment, reversible structural phase transitions proceed in the single-phase ceramics in the polyphase ceramics, the recrystallization processes occur, which result in homogenization of its structure

  19. Investigations of the Propagation of Plant Pollen by an Indicator Activation Method

    Energy Technology Data Exchange (ETDEWEB)

    Fendrik, I.; Glubrecht, H. [Technische Hochschule, Hanover (Germany)

    1967-10-15

    The study of the propagation of plant pollen is of special interest in ecology and plant breeding. Generally, radioactive labelling cannot be applied for this purpose since radioactive contamination of the materials under investigation cannot be tolerated. Instead, labelling can be performed by the use of an indicator element that has a high cross-section for neutron activation. This substance is introduced into the plant under consideration. The flying pollen is caught by polyethylene foils by means of electrostatic attraction. The foils with the pollen are irradiated in a nuclear reactor with a suitable flux of thermal neutrons. The labelled pollen grains can be detected and counted by autoradiography or by direct measurement. The method has proved satisfactory for pines and sugar beet. Indicator elements used for detection by neutron activation were manganese and dysprosium. (author)

  20. Thermalization calorimetry: A simple method for investigating glass transition and crystallization of supercooled liquids

    Directory of Open Access Journals (Sweden)

    Bo Jakobsen

    2016-05-01

    Full Text Available We present a simple method for fast and cheap thermal analysis on supercooled glass-forming liquids. This “Thermalization Calorimetry” technique is based on monitoring the temperature and its rate of change during heating or cooling of a sample for which the thermal power input comes from heat conduction through an insulating material, i.e., is proportional to the temperature difference between sample and surroundings. The monitored signal reflects the sample’s specific heat and is sensitive to exo- and endothermic processes. The technique is useful for studying supercooled liquids and their crystallization, e.g., for locating the glass transition and melting point(s, as well as for investigating the stability against crystallization and estimating the relative change in specific heat between the solid and liquid phases at the glass transition.

  1. Developing a spatial-temporal method for the geographic investigation of shoeprint evidence.

    Science.gov (United States)

    Lin, Ge; Elmes, Gregory; Walnoha, Mike; Chen, Xiannian

    2009-01-01

    This article examines the potential of a spatial-temporal method for analysis of forensic shoeprint data. The large volume of shoeprint evidence recovered at crime scenes results in varied success in matching a print to a known shoe type and subsequently linking sets of matched prints to suspected offenders. Unlike DNA and fingerprint data, a major challenge is to reduce the uncertainty in linking sets of matched shoeprints to a suspected serial offender. Shoeprint data for 2004 were imported from the Greater London Metropolitan Area Bigfoot database into a geographic information system, and a spatial-temporal algorithm developed for this project. The results show that by using distance and time constraints interactively, the number of candidate shoeprints that can implicate one or few suspects can be substantially reduced. It concludes that the use of space-time and other ancillary information within a geographic information system can be quite helpful for forensic investigation.

  2. Investigation of Reliabilities of Bolt Distances for Bolted Structural Steel Connections by Monte Carlo Simulation Method

    Directory of Open Access Journals (Sweden)

    Ertekin Öztekin Öztekin

    2015-12-01

    Full Text Available Design of the distance of bolts to each other and design of the distance of bolts to the edge of connection plates are made based on minimum and maximum boundary values proposed by structural codes. In this study, reliabilities of those distances were investigated. For this purpose, loading types, bolt types and plate thicknesses were taken as variable parameters. Monte Carlo Simulation (MCS method was used in the reliability computations performed for all combination of those parameters. At the end of study, all reliability index values for all those distances were presented in graphics and tables. Results obtained from this study compared with the values proposed by some structural codes and finally some evaluations were made about those comparisons. Finally, It was emphasized in the end of study that, it would be incorrect of the usage of the same bolt distances in the both traditional designs and the higher reliability level designs.

  3. Investigating groundwater salinity in the Machile-Zambezi Basin (Zambia) with hydrogeophysical methods

    DEFF Research Database (Denmark)

    Chongo, Mkhuzo; A. Nyambe, Imasiku; Larsen, Flemming

    resources worldwide. This thesis presents the application of geo-electrical and electromagnetic methods for the investigation of groundwater salinity in the Machile-Zambezi Basin in south western Zambia, southern central Africa. Aerial and ground based transient electromagnetic measurenments were used...... use of direct current and transient electromagnetic data in one optimization. The result from the regional mapping with transient electromagnetic measurenments showed a spatial distribution of electrical resistivity that indicated block faulting in the Machile-Zambezi Basin. Saline groundwater...... parameters. This was for a coupled flow and solute transport model setup for the Kasaya transect under the forcing of evapotranspiration. Performance of the coupled hydrogeophysical inversion was better with the inclusion of direct current data in comparison to the use of transient electromagnetic data alone...

  4. An Investigation to Manufacturing Analytical Services Composition using the Analytical Target Cascading Method.

    Science.gov (United States)

    Tien, Kai-Wen; Kulvatunyou, Boonserm; Jung, Kiwook; Prabhu, Vittaldas

    2017-01-01

    As cloud computing is increasingly adopted, the trend is to offer software functions as modular services and compose them into larger, more meaningful ones. The trend is attractive to analytical problems in the manufacturing system design and performance improvement domain because 1) finding a global optimization for the system is a complex problem; and 2) sub-problems are typically compartmentalized by the organizational structure. However, solving sub-problems by independent services can result in a sub-optimal solution at the system level. This paper investigates the technique called Analytical Target Cascading (ATC) to coordinate the optimization of loosely-coupled sub-problems, each may be modularly formulated by differing departments and be solved by modular analytical services. The result demonstrates that ATC is a promising method in that it offers system-level optimal solutions that can scale up by exploiting distributed and modular executions while allowing easier management of the problem formulation.

  5. Efficiency indicators versus forntier methods: an empirical investigation of italian public hospitals

    Directory of Open Access Journals (Sweden)

    Lorenzo Clementi

    2013-05-01

    Full Text Available Efficiency has a key-role in the measurement of the impact of the National Health Service (NHS reforms. We investigate the issue of inefficiency in health sector and provide empirical evidence derived from Italian public hospitals. Despite the importance of efficiency measurement in health care services, only recently advanced econometric methods have been applied to hospital data. We provide a synoptic survey of few empirical analyses of efficiency measurement in health care services. An estimate of the cost efficiency level in Italian public hospitals during 2001-2003 is obtained through a sample. We propose an efficiency indicator and provide cost frontiers for such hospitals, using stochastic frontier analysis (SFA for longitudinal data.

  6. An Investigation of ABF++, LSCM, and ARAP Methods for Parametrization of Shoetrees

    Directory of Open Access Journals (Sweden)

    Martynas Sabaliauskas

    2015-07-01

    Full Text Available This paper discusses on the numerical model flattening algorithms enabling the representation of straightened surface of three-dimensional objects in the plane. These algorithms are widely used in the engineering industry which requires a precise representation of surfaces of various fragments of 2D maps, such as the automotive industry. One of the examples of the application in the manufacture of footwear could be automatic formation of molds using shoetrees, which are usually produced by a unit ignoring the fact that manufacturers are still using wax foil for flattening. This paper provides an investigation of the most widely used 3D object surface flattening algorithms and also the comparison of molds of shoetrees obtained by these methods.

  7. On the sensitivity of FPPE - TWRC method in thermal effusivity investigations of solids

    International Nuclear Information System (INIS)

    Dadarlat, Dorin; Streza, Mihaela; Pop, Mircea N; Tosa, Valer

    2009-01-01

    The front detection configuration (FPPE) together with the thermal-wave-resonator-cavity (TWRC) method was used for direct measurement of the thermal effusivity of solid materials inserted as backings in the FPPE detection cell. It was demonstrated that the normalized phase of the FPPE signal has an oscillating dependence as a function of sample's thickness. The paper presents experimental results on solid materials, with various values of thermal effusivity (Cu, brass, steel, bakelite, wood). A study of the sensitivity of the technique for different liquid/backing effusivity ratios is performed. The highest sensitivity was obtained when investigating solids with values of thermal effusivity not far from the effusivity of the liquid layer of the detection cell.

  8. Controlled in meso phase crystallization--a method for the structural investigation of membrane proteins.

    Directory of Open Access Journals (Sweden)

    Jan Kubicek

    Full Text Available We investigated in meso crystallization of membrane proteins to develop a fast screening technology which combines features of the well established classical vapor diffusion experiment with the batch meso phase crystallization, but without premixing of protein and monoolein. It inherits the advantages of both methods, namely (i the stabilization of membrane proteins in the meso phase, (ii the control of hydration level and additive concentration by vapor diffusion. The new technology (iii significantly simplifies in meso crystallization experiments and allows the use of standard liquid handling robots suitable for 96 well formats. CIMP crystallization furthermore allows (iv direct monitoring of phase transformation and crystallization events. Bacteriorhodopsin (BR crystals of high quality and diffraction up to 1.3 Å resolution have been obtained in this approach. CIMP and the developed consumables and protocols have been successfully applied to obtain crystals of sensory rhodopsin II (SRII from Halobacterium salinarum for the first time.

  9. Investigation of Detectability of Elementary Composition of Rainbow trout muscle with EDS (Energy Dispersive Spectroscopy Method

    Directory of Open Access Journals (Sweden)

    Saltuk Buğrahan CEYHUN

    2017-06-01

    Full Text Available In present study, it is investigated that detectability of elementary composition of rainbow trout muscle using Energy Dispersive Spectroscopy (EDS. EDS system which has worked with attached to scanning electron microscope can do qualitative and semi-quantitative elementary analyses on selected region of sample using characteristic X-rays. For this purpose, it was performed four point and two mapping analyses from four samples. According to results, it was detected 13 elements which are consist of C, N and O in 87.70 percentage. As a result, although the method is sensitive and reliable, it is concluded that not adequate for elemental analysis alone but can be used as a support for analyzes with systems such as especially atomic absorption and ICP-MS.

  10. Life coaching following haematopoietic stem cell transplantation: a mixed-method investigation of feasibility and acceptability.

    Science.gov (United States)

    Kenyon, M; Young, F; Mufti, G J; Pagliuca, A; Lim, Z; Ream, E

    2015-07-01

    Haematopoietic stem cell transplantation (HSCT) cures many haematological cancers. Recovery post-HSCT is physically and psychologically challenging, lasting several months. Beyond the first post-transplant year, a fifth report difficulties encompassing practical, social and emotional domains, including finance and employment. We investigated the feasibility, acceptability and impact of a life coaching intervention designed to address psychosocial 'survivor' concerns of HSCT recipients and facilitate transition to life post-treatment. A concurrent embedded experimental mixed-method design was employed. Pre- and post-intervention data collection comprised qualitative semi-structured telephone interviews and quantitative postal questionnaires. Seven purposively sampled HSCT recipients (life coaching delivered by a professional life coach fortnightly over 8 weeks. Participants reported less anxiety, depression and fewer survivor concerns post-intervention, with a trend for lower social difficulties and increased functional well-being. Perceived self-efficacy was unchanged. Life coaching was feasible to deliver and acceptable to the participants who indicated it was a positive experience, with benefits described in diverse areas including work, lifestyle and hobbies. Life coaching within cancer services potentially offers the means to address psychosocial concerns and support transition to life after treatment, enabling patients to reach their potential, e.g. returning to employment and financial independence. Further investigation of this intervention in cancer survivors is warranted. © 2015 John Wiley & Sons Ltd.

  11. Application of environmetric methods to investigate control factors on water quality

    Directory of Open Access Journals (Sweden)

    Boyacioglu Hülya

    2017-09-01

    Full Text Available In the study, environmetric methods were successfully performed a to explore natural and anthropogenic controls on reservoir water quality, b to investigate spatial and temporal differences in quality, and c to determine quality variables discriminating three reservoirs in Izmir, Turkey. Results showed that overall water quality was mainly governed by “natural factors” in the whole region. A parameter that was the most important in contributing to water quality variation for one reservoir was not important for another. Between summer and winter periods, difference in arsenic concentrations were statistically significant in the Tahtalı, Ürkmez and iron concentrations were in the Balçova reservoirs. Observation of high/low levels in two seasons was explained by different processes as for instance, dilution from runoff at times of high flow seeped through soil and entered the river along with the rainwater run-off and adsorption. Three variables “boron, arsenic and sulphate” discriminated quality among Balçova & Tahtalı, Balçova & Ürkmez and two variables “zinc and arsenic” among the Tahtalı & Ürkmez reservoirs. The results illustrated the usefulness of multivariate statistical techniques to fingerprint pollution sources and investigate temporal/spatial variations in water quality.

  12. Methods and instrumentation for investigating Hall sensors during their irradiation in nuclear research reactors

    International Nuclear Information System (INIS)

    Bolshakova, I.; Holyaka, R.; Makido, E.; Marusenkov, A.; Shurygin, F.; Yerashok, V.; Moreau, P. J.; Vayakis, G.; Duran, I.; Stockel, J.; Chekanov, V.; Konopleva, R.; Nazarkin, I.; Kulikov, S.; Leroy, C.

    2009-01-01

    Present work discusses the issues of creating the instrumentation for testing the semiconductor magnetic field sensors during their irradiation with neutrons in nuclear reactors up to fluences similar to neutron fluences in steady-state sensor locations in ITER. The novelty of the work consists in Hall sensor parameters being investigated: first, directly during the irradiation (in real time), and, second, at high irradiation levels (fast neutron fluence > 10 18 n/cm 2 ). Developed instrumentation has been successfully tested and applied in the research experiments on radiation stability of magnetic sensors in IBR-2 (JINR, Dubna) and VVR-M (PNPI, Saint-Petersburg) reactors. The 'Remote-Rad' bench consists of 2 heads (head 1 and head 2) bearing investigated sensors put in a ceramic setting, of electronic unit, of personal computer and of signal lines. Each head contains 6 Hall sensors and a coil for generating test magnetic field. Moreover head 1 contains thermocouples for temperature measurement while the temperature of head 2 is measured by thermo-resistive method. The heads are placed in the reactor channel

  13. Method Development of Cadmium Investigation in Rice by Radiochemical Neutron Activation Analysis

    International Nuclear Information System (INIS)

    Promsawad, Arunee; Pareepart, Ratirot; Laoharojanaphand, Sirinart; Arunee, Kongsakpaisal

    2007-08-01

    Full text: A radiochemical neutron activation analysis for the determination of cadmium was investigated. A chemical separation of cadmium utilized ion exchange chromatography of a strong basic anion-exchange resin BIO-RAD 1X 8 (Chloride form). The adsorbing medium of 2M HCl was found to be the most suitable among the concentration attempted (2, 4, 6, 8 and 10M HCl) and the eluent for desorption of the cadmium from column was 8M NH 3 solution. A chemical yield of 95% was found. The method has been evaluated by analyzing certified reference materials with 0.5.g/g (SRM 1577b, Bovine Liver) and 2.48.g/g (SRM 1566b, Oyster Tissue) cadmium. The agreement of the result with certified values is within 92% for Bovine Liver and 96% for Oyster Tissue. The method developed was applied to determine the cadmium concentrations in contaminated Thai rice. It was found that the cadmium concentrations ranged from 7.4 to 578.9 ppb

  14. Evaluation and development of hydrogeological and geochemical investigation methods for aquifers of low permeability

    International Nuclear Information System (INIS)

    Wijland, G.C.; Langemeijer, H.D.; Stapper, R.A.M.; Glasbergen, P.; Michelot, J.L.

    1991-01-01

    Studies are currently being carried out in the Netherlands to assess the environmental consequences of geological disposal of radioactive waste. In these studies transport models are used to evaluate the geohydrological system in formations overlying the potential host-rock, and to establish the potential pathways for radionuclides to the biosphere. Knowledge of parameter values, and of their variability for the investigated formations, is necessary to construct these models. From preceding work it became obvious that only a poor set of data is available, in particular for Paleogene and Upper Cretaceous deposits, that are present in the overburden of salt structures in the Netherlands. Within the current phase of the Netherlands programme on geological disposal it was considered essential to obtain an overview of methods and their accuracy which would be applicable for a geohydrological research programme first. From this work guidelines for the construction of new boreholes might also be derived. The main purposes of this study were defined as follows: to evaluate and to test techniques to obtain geohydrological data of the aquifers and aquitards of the Upper Cretaceous and Lower Tertiary formations. Also, geohydrochemical methods were evaluated and tested in order to find out whether they could contribute to the understanding of the groundwater flow system in aquifers of low permeability

  15. Methods of investigation and analysis on groundwater using radon as an indicator

    International Nuclear Information System (INIS)

    Hamada, Hiromasa; Imaizumi, Masayuki; Komae, Takami

    1997-01-01

    As for groundwater, the quality is good, and the temperature is constant throughout year, further, it can be easily utilized only by digging wells. The quantity of its utilization in one year is about 20% of total water utilization, and about 17 billion m 3 . Recently in Japan, the frequency of occurrence of water shortage is high, and the supply of river water is unstable, therefore, the importance of groundwater increased. It is indispensable to grasp in detail the state of groundwater flow as groundwater pollution is actualized, and the water quality has become problem. As the principle that radon becomes the index for groundwater analysis, the physical characteristic of radon and the features of the radon in groundwater are explained. The method of measuring radon concentration in groundwater and surface water is described. The investigation and analysis methods, to which the processes of radon formation and radon decay are applied, in which the equilibrium radon concentration in groundwater is used as the index, to which the relation of the degree of saturation in aquifer to the radon concentration in liquid phase is applied, and to which the difference of the concentrations in surface water and groundwater is applied, are reported. (K.I.)

  16. A method for investigating protein-protein interactions related to Salmonella typhimurium pathogenesis

    Energy Technology Data Exchange (ETDEWEB)

    Chowdhury, Saiful M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Shi, Liang [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Yoon, Hyunjin [Dartmouth College, Hanover, NH (United States); Ansong, Charles [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rommereim, Leah M. [Dartmouth College, Hanover, NH (United States); Norbeck, Angela D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Auberry, Kenneth J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Moore, R. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Adkins, Joshua N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Heffron, Fred [Oregon Health and Science Univ., Portland, OR (United States); Smith, Richard D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2009-02-10

    We successfully modified an existing method to investigate protein-protein interactions in the pathogenic bacterium Salmonella typhimurium (STM). This method includes i) addition of a histidine-biotin-histidine tag to the bait proteins via recombinant DNA techniques; ii) in vivo cross-linking with formaldehyde; iii) tandem affinity purification of bait proteins under fully denaturing conditions; and iv) identification of the proteins cross-linked to the bait proteins by liquid-chromatography in conjunction with tandem mass-spectrometry. In vivo cross-linking stabilized protein interactions permitted the subsequent two-step purification step conducted under denaturing conditions. The two-step purification greatly reduced nonspecific binding of non-cross-linked proteins to bait proteins. Two different negative controls were employed to reduce false-positive identification. In an initial demonstration of this approach, we tagged three selected STM proteins- HimD, PduB and PhoP- with known binding partners that ranged from stable (e.g., HimD) to transient (i.e., PhoP). Distinct sets of interacting proteins were identified with each bait protein, including the known binding partners such as HimA for HimD, as well as anticipated and unexpected binding partners. Our results suggest that novel protein-protein interactions may be critical to pathogenesis by Salmonella typhimurium. .

  17. Coupling Strategies Investigation of Hybrid Atomistic-Continuum Method Based on State Variable Coupling

    Directory of Open Access Journals (Sweden)

    Qian Wang

    2017-01-01

    Full Text Available Different configurations of coupling strategies influence greatly the accuracy and convergence of the simulation results in the hybrid atomistic-continuum method. This study aims to quantitatively investigate this effect and offer the guidance on how to choose the proper configuration of coupling strategies in the hybrid atomistic-continuum method. We first propose a hybrid molecular dynamics- (MD- continuum solver in LAMMPS and OpenFOAM that exchanges state variables between the atomistic region and the continuum region and evaluate different configurations of coupling strategies using the sudden start Couette flow, aiming to find the preferable configuration that delivers better accuracy and efficiency. The major findings are as follows: (1 the C→A region plays the most important role in the overlap region and the “4-layer-1” combination achieves the best precision with a fixed width of the overlap region; (2 the data exchanging operation only needs a few sampling points closer to the occasions of interactions and decreasing the coupling exchange operations can reduce the computational load with acceptable errors; (3 the nonperiodic boundary force model with a smoothing parameter of 0.1 and a finer parameter of 20 can not only achieve the minimum disturbance near the MD-continuum interface but also keep the simulation precision.

  18. INVESTIGATION OF HEALTH EFFECT OF FRUIT JUICE FROM LINGONBERRY (VACCINIUM VITIS - IDEA VIA PHYSICOCHEMICAL METHODS

    Directory of Open Access Journals (Sweden)

    Poli Radusheva

    2017-10-01

    Full Text Available Objective: Antioxidants reduce cell damaging effects of free radicals, they also are used as medications to treat various forms of brain injury. Forest fruits as a lingonberry contain a lot of flavonoids and antioxidant supplements which contribute to the protection of different types of cancers and cardiovascular health problems. Purpose: The aim of this study is to explore the relations between natural fluorescence in juice from lingonberry and its total phenolic content and total antioxidant capacity in view of the usefulness of these compounds for human health and hygiene of food. Materials and Methods: For this reason, the juices from lingonberry from the region of Velingrad еnriched with lactulose will be investigated by using optical methods (colour measuring, fluorescence spectroscopy, rheological properties and sensor analysis. It may be an alternative method for quantifying the phenols and vitamins in juice from wild berries. Results: The dependences between chemical parameters, colour characteristics and the ratio between the intensity of emission and the intensity of excitation for exciting wavelength 275 nm have been found. The dependence between antioxidant activity and total phenolic content also exists. Excitation in the UV region is suitable for distinguishing the phenolic content and antioxidant compounds. The most suitable wavelengths found to be 265 nm and 275 nm. Lingonberry juices with lactulose exhibited non-Newtonian behaviour and Ostwald-de-Waele model are applied to calculate its rheological properties. Conclusions: The natural fluorescence of the lingonberry juices was correlated with their antioxidant properties, total phenolic content and lightness. From fluorescence spectra three groups of fluorescence components are determined – phenolic acids, tannins and flavonoids. The obtained results and discussion presented here give the direction for further studies and additional test for validation of the correlation

  19. Electrophysiological Investigation of Different Methods of Anesthesia in Lobster and Crayfish

    Science.gov (United States)

    Fregin, Torsten; Bickmeyer, Ulf

    2016-01-01

    Objectives In search for methods of anesthesia of crustaceans, an implanted electrode into lobster and crayfish CNS enabled us to monitor signal propagation in the nerve system of animals undergoing different protocols. Results Cooling (tap water 0°C, sea water -1,8°C) and anesthesia with MgCl2 (10%) were both discarded as anesthetic procedures because responses to external stimuli were still detectable under treatment. Contrarily, bubbling the aquarium water with CO2 can be considered a “partially successful” anesthesia, because signal propagation is inhibited but before that the animals show discomfort. The procedure of “electro-stunning” induces epileptic-form seizures in the crustacean CNS (lobster, crayfish), which overlay but do not mitigate the response to external stimuli. After several minutes the activity declines before the nervous system starts to recover. A feasible way to sacrifice lobsters is to slowly raise the water temperature (1°C min-1), as all electrical activities in the CNS cease at temperatures above ~30°C, whereas below this temperature the animals do not show signs of stress or escape behavior (e.g. tail flips) in the warming water. Conclusion CO2 is efficient to anaesthetize lobster and crayfish but due to low pH in water is stressful to the animals previous to anesthesia. Electrical stunning induces epileptiform seizures but paralyses the animals and leads to a reversible decline of nerve system activity after seizure. Electric stunning or slowly warming just before preparation may meet ethical expectations regarding anaesthesia and to sacrifice crustaceans. PMID:27642755

  20. INVESTIGATION OF THE TOTAL ORGANIC HALOGEN ANALYTICAL METHOD AT THE WASTE SAMPLING CHARACTERIZATION FACILITY (WSCF)

    International Nuclear Information System (INIS)

    DOUGLAS JG; MEZNARICH HD, PHD; OLSEN JR; ROSS GA; STAUFFER M

    2008-01-01

    Total organic halogen (TOX) is used as a parameter to screen groundwater samples at the Hanford Site. Trending is done for each groundwater well, and changes in TOX and other screening parameters can lead to costly changes in the monitoring protocol. The Waste Sampling and Characterization Facility (WSCF) analyzes groundwater samples for TOX using the United States Environmental Protection Agency (EPA) SW-846 method 9020B (EPA 1996a). Samples from the Soil and Groundwater Remediation Project (S and GRP) are submitted to the WSCF for analysis without information regarding the source of the sample; each sample is in essence a 'blind' sample to the laboratory. Feedback from the S and GRP indicated that some of the WSCF-generated TOX data from groundwater wells had a number of outlier values based on the historical trends (Anastos 2008a). Additionally, analysts at WSCF observed inconsistent TOX results among field sample replicates. Therefore, the WSCF lab performed an investigation of the TOX analysis to determine the cause of the outlier data points. Two causes were found that contributed to generating out-of-trend TOX data: (1) The presence of inorganic chloride in the groundwater samples: at inorganic chloride concentrations greater than about 10 parts per million (ppm), apparent TOX values increase with increasing chloride concentration. A parallel observation is the increase in apparent breakthrough of TOX from the first to the second activated-carbon adsorption tubes with increasing inorganic chloride concentration. (2) During the sample preparation step, excessive purging of the adsorption tubes with oxygen pressurization gas after sample loading may cause channeling in the activated-carbon bed. This channeling leads to poor removal of inorganic chloride during the subsequent wash step with aqueous potassium nitrate. The presence of this residual inorganic chloride then produces erroneously high TOX values. Changes in sample preparation were studied to more

  1. Science Self-Efficacy in the Primary Classroom: Using Mixed Methods to Investigate Sources of Self-Efficacy

    Science.gov (United States)

    Webb-Williams, Jane

    2017-04-01

    Self-efficacy has been shown to influence student engagement, effort and performance as well as course selection and future career choice. Extending our knowledge regarding the development of self-efficacy has important implications for educators and for those concerned about the international uptake of science careers. Previous research has identified four sources that may contribute towards self-efficacy: mastery experiences, vicarious experiences, verbal persuasion and physiological/affective states. Very little research has been conducted within the school environment that looks at the formation of these sources and yet early school experiences have been posited to be a key factor in girls' lack of engagement in post compulsory science education. This paper investigates children's self-efficacy beliefs in science and reports on findings from mixed method research conducted with 182 children aged between 10 and 12 years. Classroom data were collected through focus groups, individual interviews and surveys. Findings revealed that although girls and boys held similar levels of academic performance in science, many girls underestimated their capability. The four sources of self-efficacy identified by Bandura (1997) plus self-regulation as an additional source, were evident in the children's descriptions, with boys being more influenced by mastery experience and girls by a combination of vicarious experience and physiological/affective states. Girl's appraisal of information appeared to operate through a heuristic process whereby girls disregarded salient information such as teacher feedback in favour of reliance on social comparison. Contextual factors were identified. Implications for science teachers are discussed.

  2. Typing DNA profiles from previously enhanced fingerprints using direct PCR.

    Science.gov (United States)

    Templeton, Jennifer E L; Taylor, Duncan; Handt, Oliva; Linacre, Adrian

    2017-07-01

    Fingermarks are a source of human identification both through the ridge patterns and DNA profiling. Typing nuclear STR DNA markers from previously enhanced fingermarks provides an alternative method of utilising the limited fingermark deposit that can be left behind during a criminal act. Dusting with fingerprint powders is a standard method used in classical fingermark enhancement and can affect DNA data. The ability to generate informative DNA profiles from powdered fingerprints using direct PCR swabs was investigated. Direct PCR was used as the opportunity to generate usable DNA profiles after performing any of the standard DNA extraction processes is minimal. Omitting the extraction step will, for many samples, be the key to success if there is limited sample DNA. DNA profiles were generated by direct PCR from 160 fingermarks after treatment with one of the following dactyloscopic fingerprint powders: white hadonite; silver aluminium; HiFi Volcano silk black; or black magnetic fingerprint powder. This was achieved by a combination of an optimised double-swabbing technique and swab media, omission of the extraction step to minimise loss of critical low-template DNA, and additional AmpliTaq Gold ® DNA polymerase to boost the PCR. Ninety eight out of 160 samples (61%) were considered 'up-loadable' to the Australian National Criminal Investigation DNA Database (NCIDD). The method described required a minimum of working steps, equipment and reagents, and was completed within 4h. Direct PCR allows the generation of DNA profiles from enhanced prints without the need to increase PCR cycle numbers beyond manufacturer's recommendations. Particular emphasis was placed on preventing contamination by applying strict protocols and avoiding the use of previously used fingerprint brushes. Based on this extensive survey, the data provided indicate minimal effects of any of these four powders on the chance of obtaining DNA profiles from enhanced fingermarks. Copyright © 2017

  3. Whither RDS? An investigation of Respondent Driven Sampling as a method of recruiting mainstream marijuana users

    Directory of Open Access Journals (Sweden)

    Cousineau Marie-Marthe

    2010-07-01

    Full Text Available Abstract Background An important challenge in conducting social research of specific relevance to harm reduction programs is locating hidden populations of consumers of substances like cannabis who typically report few adverse or unwanted consequences of their use. Much of the deviant, pathologized perception of drug users is historically derived from, and empirically supported, by a research emphasis on gaining ready access to users in drug treatment or in prison populations with higher incidence of problems of dependence and misuse. Because they are less visible, responsible recreational users of illicit drugs have been more difficult to study. Methods This article investigates Respondent Driven Sampling (RDS as a method of recruiting experienced marijuana users representative of users in the general population. Based on sampling conducted in a multi-city study (Halifax, Montreal, Toronto, and Vancouver, and compared to samples gathered using other research methods, we assess the strengths and weaknesses of RDS recruitment as a means of gaining access to illicit substance users who experience few harmful consequences of their use. Demographic characteristics of the sample in Toronto are compared with those of users in a recent household survey and a pilot study of Toronto where the latter utilized nonrandom self-selection of respondents. Results A modified approach to RDS was necessary to attain the target sample size in all four cities (i.e., 40 'users' from each site. The final sample in Toronto was largely similar, however, to marijuana users in a random household survey that was carried out in the same city. Whereas well-educated, married, whites and females in the survey were all somewhat overrepresented, the two samples, overall, were more alike than different with respect to economic status and employment. Furthermore, comparison with a self-selected sample suggests that (even modified RDS recruitment is a cost-effective way of

  4. Investigation of toxigenic potential of fungal species by the use of simple screening method

    Directory of Open Access Journals (Sweden)

    Bočarov-Stančić Aleksandra S.

    2009-01-01

    Full Text Available Potential for the biosynthesis of aflatoxin B1 (AFLB1, ochratoxin A (OTA, diacetoxyscirpenol (DAS, T-2 toxin (T2, and zearalenone (ZON was investigated in different fungal species belonging to the genera: Aspergillus, Fusarium and Penicillium. The majority of investigated isolates originated from cereal grains, crushed oil soybean seed and fodder mixtures. The simple screening method developed by Filtenborg et al. (1983 was applied with few modifications concerning the type of the medium and cultivation temperature. In order to optimise the biosynthetic conditions for different mycotoxins, the following control cultures, known as mycotin producers were used: OTA - A. ochraceus CBS 108.08, DAS - F. semitectum (SL-B i SL-C, T2 - F. sporotrichioides (ITM-391, M-1-1, R-2301 and ZON - F. graminearum (GZ-LES. The fungi were cultivated on the standard medium (YESA - 2% yeast extract, 15% sucrose and 2% agar, pH 6.5, three modifications of the basic medium (YESAZn - the standard medium supplemented with 0.23 mg/l ZnSO4 x 5 H2O; PPSA - the medium in which yeast extract was replaced with peptone-1; PPSAZn - the medium in which yeast extract was replaced with peptone-1 and supplemented with 0.23 mg/l ZnSO4 x 5 H2O, and the potato-dextrose agar (PDA. The earlier biosynthesis of tested mycotoxins was recorded under the following cultivation conditions of fungal species: AFLB1 - after 14 days on PDA at 27±1°C, OTA - after 10 days on YESA and YESAZn at 27±1°C, DAS - after 10 days on PPSA and PPSAZn at 27±1°C, T2 - after 7 days on PPSAZn and PPSA at room temperature (20-24°C, and ZON - after 1 week on YESA and YESAZn at room temperature (21-24°C.

  5. Integrating Lesion-Symptom Mapping with Other Methods to Investigate Language Networks and Aphasia Recovery

    Directory of Open Access Journals (Sweden)

    Peter E Turkeltaub

    2015-04-01

    Full Text Available Voxel-based lesion-symptom mapping (VLSM has provided valuable insights into the neural underpinnings of various language functions. Integrating lesion mapping methods with other neuroscience techniques may provide new opportunities to investigate questions related both to the neurobiology of language and to plasticity after brain injury. For example, recent diffusion tensor imaging studies have explored relationships between aphasia symptomology and damage in specific white matter tracts (Forkel et al., 2014 or disruption of the white matter connectome (Bonilha, Rorden, & Fridriksson, 2014. VLSM has also recently been used to assess correlations between lesion location and response to transcranial direct current stimulation aphasia treatment (Campana, Caltagirone, & Marangolo, 2015. We have recently undertaken studies integrating VLSM with other techniques, including voxel-based morphometry (VBM and functional MRI, in order to investigate how parts of the brain spared by stroke contribute to recovery. VLSM can be used in this context to map lesions associated with particular patterns of plasticity in brain structure, function, or connectivity. We have also used VLSM to estimate the variance in behavior due to the stroke itself so that this lesion-symptom relationship can be controlled for when examining the contributions of the rest of the brain. Using this approach in combination with VBM, we have identified areas of the right temporoparietal cortex that appear to undergo hypertrophy after stroke and compensate for speech production deficits. In this talk, I will review recent advances in integrating lesion-symptom mapping with other imaging and brain stimulation techniques in order to better understand the brain basis of language and of aphasia recovery.

  6. An investigation of temperature measurement methods in nuclear power plant reactor pressure vessel annealing

    International Nuclear Information System (INIS)

    Acton, R.U.; Gill, W.; Sais, D.J.; Schulze, D.H.; Nakos, J.T.

    1996-05-01

    The objective of this project was to provide an assessment of several methods by which the temperature of a commercial nuclear power plant reactor pressure vessel (RPV) could be measured during an annealing process. This project was a coordinated effort between DOE's Office of Nuclear Energy, Science and Technology; DOE's Light Water Reactor Technology Center at Sandia National Laboratories; and the Electric Power Research Institute's Non- Destructive Evaluation Center. Ball- thermocouple probes similar to those described in NUREG/CR-5760, spring-loaded, metal- sheathed thermocouple probes, and 1778 air- suspended thermocouples were investigated in experiments that heated a section of an RPV wall to simulate a thermal annealing treatment. A parametric study of ball material, emissivity, thermal conductivity, and thermocouple function locations was conducted. Also investigated was a sheathed thermocouple failure mode known as shunting (electrical breakdown of insulation separating the thermocouple wires). Large errors were found between the temperature as measured by the probes and the true RPV wall temperature during heat-up and cool-down. At the annealing soak temperature, in this case 454 degrees C [850'F], all sensors measured the same temperature within about ±5% (23.6 degrees C [42.5 degrees F]). Because of these errors, actual RPV wall heating and cooling rates differed from those prescribed (by up to 29%). Shunting does not appear to be a problem under these conditions. The large temperature measurement errors led to the development of a thermal model that predicts the RPV wall temperature from the temperature of a ball- probe. Comparisons between the model and the experimental data for ball-probes indicate that the model could be a useful tool in predicting the actual RPV temperature based on the indicated ball- probe temperature. The model does not predict the temperature as well for the spring-loaded and air suspended probes

  7. Molecular biological methods (DGGE) as a tool to investigate nitrification inhibition in wastewater treatment.

    Science.gov (United States)

    Kreuzinger, N; Farnleitner, A; Wandl, G; Hornek, R; Mach, R

    2003-01-01

    Incomplete nitrification at an activated sludge plant for biological pre-treatment of rendering plant effluents led to a detailed investigation on the origin and solution of this problem. Preliminary studies revealed that an inhibition of ammonia oxidising microorganisms (AOM) by process waters of the rendering plant was responsible for the situation. We were able to show a correlation between the existence of specific AOM and nitrification capacity expressed as oxygen uptake rate for maximal nitrification (OURNmax). Only Nitrosospira sp. was found in the activated sludge of the rendering plant and another industrial wastewater treatment plant with problems in nitrification, while reference plants without nitrification problems showed Nitrosomonas spp. as the predominant ammonia oxidising bacteria. By accompanying engineering investigations and experiments (cross-feeding experiments, operation of a two-stage laboratory plant) with molecular biological methods (DGGE--Denaturing Gradient Gel Electrophoresis) we were able to elaborate an applicable solution for the rendering plant. Laboratory experiments with a two-stage process layout finally provided complete nitrification overcoming the inhibiting nature of process waters from the rendering plant. DGGE analysis of the second stage activated sludge from the laboratory plant showed a shift in population structure from Nitrosospira sp. towards Nitrosomonas spp. simultaneous to the increase of nitrification capacity. Nitrification capacities comparable to full-scale municipal wastewater treatment plants could be maintained for more than two months. As the design of wastewater treatment plants for nitrification is linked to the growth characteristics of Nitrosomonas spp., established criteria can be applied for the redesign of the full-scale plant.

  8. A preliminary mixed-method investigation of trust and hidden signals in medical consultations.

    Directory of Open Access Journals (Sweden)

    Silvia Riva

    Full Text Available Several factors influence patients' trust, and trust influences the doctor-patient relationship. Recent literature has investigated the quality of the personal relationship and its dynamics by considering the role of communication and the elements that influence trust giving in the frame of general practitioner (GP consultations.We analysed certain aspects of the interaction between patients and GPs to understand trust formation and maintenance by focusing on communication channels. The impact of socio-demographic variables in trust relationships was also evaluated.A cross-sectional design using concurrent mixed qualitative and quantitative research methods was employed. One hundred adults were involved in a semi-structured interview composed of both qualitative and quantitative items for descriptive and exploratory purposes. The study was conducted in six community-based departments adjacent to primary care clinics in Trento, Italy.The findings revealed that patients trusted their GP to a high extent by relying on simple signals that were based on the quality of the one-to-one communication and on behavioural and relational patterns. Patients inferred the ability of their GP by adopting simple heuristics based mainly on the so-called social "honest signals" rather than on content-dependent features. Furthermore, socio-demographic variables affected trust: less literate and elderly people tended to trust more.This study is unique in attempting to explore the role of simple signals in trust relationships within medical consultation: people shape trust and give meaning to their relationships through a powerful channel of communication that orbits not around words but around social relations. The findings have implications for both clinicians and researchers. For doctors, these results suggest a way of thinking about encounters with patients. For researchers, the findings underline the importance of analysing some new key factors around trust for

  9. Investigations of oxide particles in unirradiated ODS-Eurofer by TEM and 3D atom probe methods

    International Nuclear Information System (INIS)

    Aleev, A.A.; Iskandarov, N.A.; Nikitin, A.A.; Rogizhkin, S.V.; Zaluzhny, A.G.; Klimenkov, M.; Lindau, R.; Moeslang, A.; Vladimirov, P.

    2009-01-01

    Oxide dispersion strengthened steels possess better high-temperature creep and radiation resistance than conventionally produced ferritic/martensitic steels. This behavior is mainly caused by the presence of highly dispersed and extremely stable oxide particles with sizes of few nanometers. One of the promising oxides used for dispersion strengthening was yttria (Y 2 O 3 ), which was introduced into EUROFER by mechanical alloying followed by the hot isostatic pressing at temperature around 1000-1200 dg. C and pressure ∼100 MPa. It was found that mechanical properties were strongly depended on size and spatial distribution of the precipitates. Therefore considerable efforts are focused on the investigation of the chemical composition and orientation of precipitates with respect to the steel matrix. Recent studies of Eurofer ODS steel (9%-CrWVTa) by SANS revealed the presence of high number density structural features with a size of approximately one nanometer. At the same time, previous studies by TEM identified only high number of small (6-40 nm) Y 2 O 3 particles. In this work we tried to get a deeper inside into the nanostructure of this material by means of tomographic atom probe and to correlate the results with the picture obtained by TEM. The present investigations revealed fine (∼2 nm) enrichments containing not only yttrium and oxygen but also vanadium and nitrogen. Concentration of vanadium was found to be approximately at the same level as yttrium. Some of the enrichments contained only three or even two elements mentioned above. Estimated number density of enrichments is about (1/5) x 10 23 m -3 . We suppose that these enriched zones might be precursors of the larger precipitates observed by TEM. The thesis seems to be supported by the similarities of the chemical composition and spatial distribution of elements inside enriched zones and nano precipitates studied by atomic probe and analytical TEM methods. (author)

  10. Investigation of soil structure in Uzungöl settlement area by Shallow Seismic Methods

    Directory of Open Access Journals (Sweden)

    Hakan Karslı

    2017-04-01

    Full Text Available This study was performed to relase the soil structure of Uzungöl district of Trabzon city, a vocational area, where had been formed by a historical landslide and lake deposits and to evaluate its geotechnical characters by using seismic methods which are noninvasive, rapidly applicable and provide substantial information about the structure of investigated ground in a short time. For this purpose, seismic refraction, active-passive surface waves and seismic reflections in 16 profiles were gathered on four sub-areas and and evaluated by current favorable numerical methods. Although it considerably varies between profiles, the depth of basement, depositional base of deposits, was averagely obtained as 13.5-15m at upper elevation and 25-50m at lower elevation of the study area. Dynamic elastic parameters and average shear wave velocity of the upper 30m (VS30 of soil in the area were calculated. The soil classification of study area was interpreted as locally Z1 and Z2 class for TEC, B and C class for EC-8 code, C and D class for NERHP. According to VS30 (394-530m/s, ground amplification and predominant vibration period of the study area are respectively obtained as 1.5-2.1 and 0.23-0.30sec. On the other hand, all deposits are characterized by stiffness-solid soil, excluding arable soil from surface to a few meters depth. In addition, the first meters of bedrock shows weathered character, but deeper parts are very compact and hard. Therefore, a scientific infrastructure has been formed to carry out the engineering projects to be planned for Uzungöl settletment safely and without damaging the environment.

  11. Investigation of the Dynamic Contact Angle Using a Direct Numerical Simulation Method.

    Science.gov (United States)

    Zhu, Guangpu; Yao, Jun; Zhang, Lei; Sun, Hai; Li, Aifen; Shams, Bilal

    2016-11-15

    A large amount of residual oil, which exists as isolated oil slugs, remains trapped in reservoirs after water flooding. Numerous numerical studies are performed to investigate the fundamental flow mechanism of oil slugs to improve flooding efficiency. Dynamic contact angle models are usually introduced to simulate an accurate contact angle and meniscus displacement of oil slugs under a high capillary number. Nevertheless, in the oil slug flow simulation process, it is unnecessary to introduce the dynamic contact angle model because of a negligible change in the meniscus displacement after using the dynamic contact angle model when the capillary number is small. Therefore, a critical capillary number should be introduced to judge whether the dynamic contact model should be incorporated into simulations. In this study, a direct numerical simulation method is employed to simulate the oil slug flow in a capillary tube at the pore scale. The position of the interface between water and the oil slug is determined using the phase-field method. The capacity and accuracy of the model are validated using a classical benchmark: a dynamic capillary filling process. Then, different dynamic contact angle models and the factors that affect the dynamic contact angle are analyzed. The meniscus displacements of oil slugs with a dynamic contact angle and a static contact angle (SCA) are obtained during simulations, and the relative error between them is calculated automatically. The relative error limit has been defined to be 5%, beyond which the dynamic contact angle model needs to be incorporated into the simulation to approach the realistic displacement. Thus, the desired critical capillary number can be determined. A three-dimensional universal chart of critical capillary number, which functions as static contact angle and viscosity ratio, is given to provide a guideline for oil slug simulation. Also, a fitting formula is presented for ease of use.

  12. Investigations on pelagic food webs in mountain lakes - aims and methods

    Directory of Open Access Journals (Sweden)

    Jirí NEDOMA

    1999-08-01

    Full Text Available A methodical approach for the assessment of pelagic biomass and the main carbon fluxes in remote and hardly accessible mountain lakes was elaborated and tested. Number and biomass of bacteria (BAC, autotrophic picoplankton (APP, heterotrophic nanoflagellates (HNF, ciliates (CIL, phytoplankton (PHY, zooplankton smaller than 40 μm (ZOOS and zooplankton larger than 40 μm (ZOOL were investigated regularly during two ice-free periods in 13 European mountain lakes (1st level approach – fixed samples elaborated in specialized laboratories. Carbon fluxes measured in 9 lakes included: primary production, exudation by PHY and BAC uptake of exudates, BAC production, elimination of BAC. These processes were measured in the field by specialized teams (2nd level approach. The ranges of values found in mountain lakes were evaluated and possible methodical and interpretative errors discussed. BAC were a significant component of pelagic biomass. The intercomparison between different partners showed differences in bacterial counts lower than 10%, whereas the mean cell volumes measured fluctuated by more than 40%. APP was never found in a significant quantity, except in one lake. HNF and CIL, though regularly found, were usually scarce and only occasionally significant in terms of biomass. The main components of pelagic biomass were BAC, PHY and ZOOL+ZOOS, except for acidified lakes, where zooplankton was very low. In oligotrophic mountain lakes, the percentage of extracellular production in the total primary production was considerable. Bacterial abundance and production often reached values quite comparable with the situation found in lowland mesotrophic lakes during winter.

  13. Method for investigating the applicability of thorium-based fuels in existing BWRs

    International Nuclear Information System (INIS)

    Bjoerk, Klara Insulander; Fhager, Valentin; Demaziere, Christophe

    2009-01-01

    In this paper, a methodology for investigating the applicability of thorium based fuels in existing Boiling Water Reactors is described. The same tools and methods as those used in this study are also used for design of new fuel batches for existing reactors. As an illustration of the proposed methodology and for the purpose of comparing different fissile components for thorium-based fuel, three different thorium-based fuel designs were developed, and a low enriched uranium fuel design was created in parallel as a reference. The different fuel assemblies, which are based on the mechanical fuel design GE14, were analyzed with the Studsvik Scandpower CASMO-4E code. The linear reactivity model was used to decide a suitable initial fissile content for meeting the burnup goal of 55 MWd/kgHM and the designs were optimized for attaining an even power distribution and for keeping boiling transition factors low. Such optimizations facilitate core designs that would meet prevalent demands on Linear Heat Generation Rate (LHGR) and Critical Power Ratio (CPR). The hence created fuel designs were then analyzed with regards to thermal performance, reactivity coefficients, delayed neutron fractions and control rod worths. An equilibrium core loading pattern was also developed with each one of the thus created fuel designs and analyzed with the three dimensional reactor analysis code SIMULATE-3, also developed by Studsvik Scandpower. The results of the two simulations were compared and found to be coherent, and no major obstacles were met using the given tools and methods. The analysis of the performances of the fuel assemblies and the corresponding loaded cores is reported in a companion paper (K. Insulander Bjoerk, V. Fhager, and C. Demaziere, 'Comparison of Thorium-Based Fuels with Different Fissile Components in Existing BWRs'). (author)

  14. Ultrastructural investigation of root canal dentine surface after application of active ultrasonic method

    Directory of Open Access Journals (Sweden)

    Mitić Aleksandar

    2008-01-01

    Full Text Available INTRODUCTION The basic work principle of all ultrasonic techniques is the piezoelectric effect of producing high frequency ultrasounds of small length, which are transmitted over the endodontic extensions or canal instruments into the root canal. When in contact with the tissue, ultrasonic vibrations are converted into mechanical oscillations. Ultrasonic waves and the obtained oscillations along with the synergic effect of irrigation bring about the elimination of smear layer from the root canal walls. OBJECTIVE The aim of the study was to ultrastucturally examine the effect of smear layer removal from the walls of canals by the application of the active ultrasonic method without irrigation, that is by the application of ultrasound and irrigation using distilled water and 2.5% NaOCl. METHOD The investigation comprised 35 single-canal, extracted human teeth. After removal of the root canal content, experimental samples were divided into three groups. According to the procedure required, the first group was treated by ultrasound without irrigation; the second one by ultrasound with irrigation using distilled water; and the third group was treated by ultrasound and irrigation using 2.5% NaOCl solution. The control samples were treated by machine rotating instruments (Pro-File and were rinsed by distilled water. RESULTS The obtained results showed that the ultrasonic treatment of the root canal without irrigation did not remove the smear layer. The dentine canals are masked, and big dentine particles are scattered on the intertubular dentine. The ultrasonic treatment by using irrigation with distilled water provides cleaner dentine walls and open dentine tubules but with smaller particles on the intertubular dentine. The ultrasound treatment by using irrigation with 2.5% NaOCl solution provides a clean intertubular dentine surface without a smear layer and clearly open dentine tubules. CONCLUSION Instrumentation of the root canal by application of

  15. Linking healthcare associated norovirus outbreaks: a molecular epidemiologic method for investigating transmission

    Directory of Open Access Journals (Sweden)

    Andrews Nick

    2006-07-01

    Full Text Available Abstract Background Noroviruses are highly infectious pathogens that cause gastroenteritis in the community and in semi-closed institutions such as hospitals. During outbreaks, multiple units within a hospital are often affected, and a major question for control programs is: are the affected units part of the same outbreak or are they unrelated transmission events? In practice, investigators often assume a transmission link based on epidemiological observations, rather than a systematic approach to tracing transmission. Here, we present a combined molecular and statistical method for assessing: 1 whether observed clusters provide evidence of local transmission and 2 the probability that anecdotally|linked outbreaks truly shared a transmission event. Methods 76 healthcare associated outbreaks were observed in an active and prospective surveillance scheme of 15 hospitals in the county of Avon, England from April 2002 to March 2003. Viral RNA from 64 out of 76 specimens from distinct outbreaks was amplified by reverse transcription-PCR and was sequenced in the polymerase (ORF 1 and capsid (ORF 2 regions. The genetic diversity, at the nucleotide level, was analysed in relation to the epidemiological patterns. Results Two out of four genetic and epidemiological clusters of outbreaks were unlikely to have occurred by chance alone, thus suggesting local transmission. There was anecdotal epidemiological evidence of a transmission link among 5 outbreaks pairs. By combining this epidemiological observation with viral sequence data, the evidence of a link remained convincing in 3 of these pairs. These results are sensitive to prior beliefs of the strength of epidemiological evidence especially when the outbreak strains are common in the background population. Conclusion The evidence suggests that transmission between hospitals units does occur. Using the proposed criteria, certain hypothesized transmission links between outbreaks were supported while

  16. Investigation of real tissue water equivalent path lengths using an efficient dose extinction method

    Science.gov (United States)

    Zhang, Rongxiao; Baer, Esther; Jee, Kyung-Wook; Sharp, Gregory C.; Flanz, Jay; Lu, Hsiao-Ming

    2017-07-01

    For proton therapy, an accurate conversion of CT HU to relative stopping power (RSP) is essential. Validation of the conversion based on real tissue samples is more direct than the current practice solely based on tissue substitutes and can potentially address variations over the population. Based on a novel dose extinction method, we measured water equivalent path lengths (WEPL) on animal tissue samples to evaluate the accuracy of CT HU to RSP conversion and potential variations over a population. A broad proton beam delivered a spread out Bragg peak to the samples sandwiched between a water tank and a 2D ion-chamber detector. WEPLs of the samples were determined from the transmission dose profiles measured as a function of the water level in the tank. Tissue substitute inserts and Lucite blocks with known WEPLs were used to validate the accuracy. A large number of real tissue samples were measured. Variations of WEPL over different batches of tissue samples were also investigated. The measured WEPLs were compared with those computed from CT scans with the Stoichiometric calibration method. WEPLs were determined within  ±0.5% percentage deviation (% std/mean) and  ±0.5% error for most of the tissue surrogate inserts and the calibration blocks. For biological tissue samples, percentage deviations were within  ±0.3%. No considerable difference (extinction measurement took around 5 min to produce ~1000 WEPL values to be compared with calculations. This dose extinction system measures WEPL efficiently and accurately, which allows the validation of CT HU to RSP conversions based on the WEPL measured for a large number of samples and real tissues.

  17. A pilot investigation to optimise methods for a future satiety preload study.

    Science.gov (United States)

    Hobden, Mark R; Guérin-Deremaux, Laetitia; Commane, Daniel M; Rowland, Ian; Gibson, Glenn R; Kennedy, Orla B

    2017-01-01

    Preload studies are used to investigate the satiating effects of foods and food ingredients. However, the design of preload studies is complex, with many methodological considerations influencing appetite responses. The aim of this pilot investigation was to determine acceptability, and optimise methods, for a future satiety preload study. Specifically, we investigated the effects of altering (i) energy intake at a standardised breakfast (gender-specific or non-gender specific), and (ii) the duration between mid-morning preload and ad libitum lunch meal, on morning appetite scores and energy intake at lunch. Participants attended a single study visit. Female participants consumed a 214-kcal breakfast ( n  = 10) or 266-kcal breakfast ( n  = 10), equivalent to 10% of recommended daily energy intakes for females and males, respectively. Male participants ( n  = 20) consumed a 266-kcal breakfast. All participants received a 250-ml orange juice preload 2 h after breakfast. The impact of different study timings was evaluated in male participants, with 10 males following one protocol (protocol 1) and 10 males following another (protocol 2). The duration between preload and ad libitum lunch meal was 2 h (protocol 1) or 2.5 h (protocol 2), with the ad libitum lunch meal provided at 12.00 or 13.00, respectively. All female participants followed protocol 2. Visual analogue scale (VAS) questionnaires were used to assess appetite responses and food/drink palatability. Correlation between male and female appetite scores was higher with the provision of a gender-specific breakfast, compared to non-gender-specific breakfast (Pearson correlation of 0.747 and 0.479, respectively). No differences in subjective appetite or ad libitum energy intake were found between protocols 1 and 2. VAS mean ratings of liking, enjoyment, and palatability were all > 66 out of 100 mm for breakfast, preload, and lunch meals. The findings of this pilot study confirm the acceptability

  18. Investigating methods for determining mismatch in near side vehicle impacts - biomed 2009.

    Science.gov (United States)

    Loftis, Kathryn; Martin, R Shayn; Meredith, J Wayne; Stitzel, Joel

    2009-01-01

    This study investigates vehicle mismatch in severe side-impact motor vehicle collisions. Research conducted by the Insurance Institute for Highway Safety has determined that vehicle mismatch often leads to very severe injuries for occupants in the struck vehicle, because the larger striking vehicle does not engage the lower sill upon impact, resulting in severe intrusions into the occupant compartment. Previous studies have analyzed mismatched collisions according to vehicle type, not by the difference in vehicle height and weight. It is hypothesized that the combination of a heavier striking vehicle at a taller height results in more intrusion for the struck vehicle and severe injury for the near side occupant. By analyzing Crash Injury Research and Engineering Network (CIREN) data and occupant injury severity, it is possible to study intrusion and injuries that occur due to vehicle mismatch. CIREN enrolls seriously injured occupants involved in motor vehicle crashes (MVC) across the United States. From the Toyota-Wake Forest University CIREN center, 23 near side impact cases involving two vehicles were recorded. Only 3 of these seriously injured occupant cases were not considered mismatched according to vehicle curb weight, and only 2 were not considered vehicle mismatched according to height differences. The mismatched CIREN cases had an average difference in vehicle curb weight of 737.0 kg (standard deviation of 646.8) and an average difference in vehicle height of 16.38 cm (standard deviation of 7.186). There were 13 occupants with rib fractures, 12 occupants with pelvic fractures, 9 occupants with pulmonary contusion, and 5 occupants with head injuries, among other multiple injuries. The average Injury Severity Score (ISS) for these occupants was 27, with a standard deviation of 16. The most serious injuries resulted in an Abbreviated Injury Scale (AIS) of 5, which included 3 occupants. Each of these AIS 5 injuries were to different body regions on different

  19. Investigation on multi-objective performance optimization algorithm application of fan based on response surface method and entropy method

    Science.gov (United States)

    Zhang, Li; Wu, Kexin; Liu, Yang

    2017-12-01

    A multi-objective performance optimization method is proposed, and the problem that single structural parameters of small fan balance the optimization between the static characteristics and the aerodynamic noise is solved. In this method, three structural parameters are selected as the optimization variables. Besides, the static pressure efficiency and the aerodynamic noise of the fan are regarded as the multi-objective performance. Furthermore, the response surface method and the entropy method are used to establish the optimization function between the optimization variables and the multi-objective performances. Finally, the optimized model is found when the optimization function reaches its maximum value. Experimental data shows that the optimized model not only enhances the static characteristics of the fan but also obviously reduces the noise. The results of the study will provide some reference for the optimization of multi-objective performance of other types of rotating machinery.

  20. Investigation of first ray mobility during gait by kinematic fluoroscopic imaging-a novel method

    Directory of Open Access Journals (Sweden)

    Martin Heiner

    2012-02-01

    Full Text Available Abstract Background It is often suggested that sagittal instability at the first tarso-metatarsal joint level is a primary factor for hallux valgus and that sagittal instability increases with the progression of the deformity. The assessment of the degree of vertical instability is usually made by clinical evaluation while any measurements mostly refer to a static assessment of medial ray mobility (i.e. the plantar/dorsal flexion in the sagittal plane. Testing methods currently available cannot attribute the degree of mobility to the corresponding anatomical joints making up the medial column of the foot. The aim of this study was to develop a technique which allows for a quantification of the in-vivo sagittal mobility of the joints of the medial foot column during the roll-over process under full weight bearing. Methods Mobility of first ray bones was investigated by dynamic distortion-free fluoroscopy (25 frames/s of 14 healthy volunteers and 8 patients with manifested clinical instability of the first ray. A CAD-based evaluation method allowed the determination of mobility and relative displacements and rotations of the first ray bones within the sagittal plane during the stance phase of gait. Results Total flexion of the first ray was found to be 13.63 (SD 6.14 mm with the healthy volunteers and 13.06 (SD 8.01 mm with the patients (resolution: 0.245 mm/pixel. The dorsiflexion angle was 5.27 (SD 2.34 degrees in the healthy volunteers and increased to 5.56 (SD 3.37 degrees in the patients. Maximum rotations were found at the naviculo-cuneiform joints and least at the first tarso-metatarsal joint level in both groups. Conclusions Dynamic fluoroscopic assessment has been shown to be a valuable tool for characterisation of the kinematics of the joints of the medial foot column during gait. A significant difference in first ray flexion and angular rotation between the patients and healthy volunteers however could not be found.

  1. Investigation of method for Stainless Steel Welding Wire as a Replacement for Arc Wire Comsumables

    Directory of Open Access Journals (Sweden)

    Koiprasert, H.

    2005-01-01

    Full Text Available Arc spraying as a coating method is being employed in various industrial applications as a part of maintenance service, and also as a surface engineering technique for many machine parts and components. The major cost in producing the arc spray coating is, however, based on the cost of the arc wire comsumables. This project was carried out to investigate the use of the commercially-available gas metal arc welding wire (GMAW wire as a cheaper alternative to the special-purpose arc wire comsumables. The wire material chosen for this early study is the 316L stainless steel, due to its popularity in many applications as a built-up coating for worn parts. The physical properties of the coatings produced from the two sets of 316L stainless steel wire were determined to be different in the percentage of porosity and the oxide content. The mechanical properties, including the tensile bond strength and the wear rate of the coatings produced from the two types of sprayed wire, were also different. This will, in turn, result in a slight difference in the performance of thecoatings.

  2. Investigation on the activation of coal gangue by a new compound method.

    Science.gov (United States)

    Li, Chao; Wan, Jianhua; Sun, Henghu; Li, Longtu

    2010-07-15

    In order to comprehensively utilize coal gangue as the main raw material in cementitious materials, improving its cementitious activity is a question of fundamental importance. In this paper, we present a new compound mechanical-hydro-thermal activation (CMHTA) technology to investigate the activation effect of coal gangue, and the traditional mechanical-thermal activation (TMTA) technology was used as reference. The purpose of this study is to give a detailed comparison between these two methods with regard to the mineral composition, crystal structure and microstructure, by XRD, IR, MAS NMR, XPS and mechanical property analysis. The prepared coal gangue based blended cement, containing 52% of activated coal gangue C (by CMHTA technology), has a better mechanical property than activated coal gangue T (by TMTA technology) and raw coal gangue. The results show that both of the TMTA and CMHTA technologies can improve the cementitious activity of raw gangue greatly. Moreover, compared with TMTA, the mineral phases such as feldspar and muscovite in raw coal gangue were partially decomposed, and the crystallinity of quartz decreased, due to the effect of adding CaO and hydro-thermal process of CMHTA technology. 2010 Elsevier B.V. All rights reserved.

  3. An enhanced voxel-based morphometry method to investigate structural changes: application to Alzheimer's disease

    International Nuclear Information System (INIS)

    Li, Xingfeng; Messe, Arnaud; Marrelec, Guillaume; Pelegrini-Issac, Melanie; Benali, Habib

    2010-01-01

    When characterizing regional cerebral gray matter differences in structural magnetic resonance images (sMRI) by voxel-based morphometry (VBM), one faces a known drawback of VBM, namely that histogram unequalization in the intensity images introduces false-positive results. To overcome this limitation, we propose to improve VBM by a new approach (called eVBM for enhanced VBM) that takes the histogram distribution of the sMRI into account by adding a histogram equalization step within the VBM procedure. Combining this technique with two most widely used VBM software packages (FSL and SPM), we studied GM variability in a group of 62 patients with Alzheimer's disease compared to 73 age-matched elderly controls. The results show that eVBM can reduce the number of false-positive differences in gray matter concentration. Because it takes advantage of the properties of VBM while improving sMRI histogram distribution at the same time, the proposed method is a powerful approach for analyzing gray matter differences in sMRI and may be of value in the investigation of sMRI gray and white matter abnormalities in a variety of brain diseases. (orig.)

  4. Investigation of ZnTe thin films grown by Pulsed Laser Deposition method

    International Nuclear Information System (INIS)

    Kotlyarchuk, B.; Savchuk, V.

    2007-01-01

    This paper is devoted to optimization of the Pulsed Laser Deposition (PLD) growth condition of ZnTe films on various substrates and subsequent investigation of relevant parameters of growth process, structural, optical and electrical properties of grown films. Studies of the effect of growth parameters on the structural quality and properties of grown films were carried out. X-ray diffraction measurements showed that the ZnTe films, which have been deposited at optimal substrate temperatures, were characterized by a (111) preferred orientation with large average grain size. The optical transmission and reflectance in the energy range 1.5-5.5 eV for films grown at various substrate temperatures were measured. We calculated the variation in the absorption coefficient with the photon energy from the transmittance spectrum for samples grown at various substrate temperatures. Obtained data were analyzed and the value of the absorption coefficient, for allowed direct transitions, has been determined as a function of photon energy. We found that the undoped ZnTe films, which were grown by the PLD method, are typically p-type and possess resistivity in the range of 10 3 Ωcm at room temperature. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  5. An empirical survey to investigate quality of men's clothing market using QFD method

    Directory of Open Access Journals (Sweden)

    Samira Golshan

    2012-08-01

    Full Text Available One of the most important techniques on improving customer satisfaction in clothing and textile industry is to increase the quality of goods and services. There are literally different methods for detecting important items influencing clothing products and the proposed model of this paper uses quality function deployment (QFD. The proposed model of this paper designs and distributes a questionnaire among some experts to detect necessary factors and using house of quality we determine the most important factors impacting the customer's clothing selection. The proposed study of this paper focuses men who are 15 to 45 years old living in Yazd/Iran. The brand we do the investigation sells the products in three shopping centers located in this city. We have distributed 100 questionnaires and collected 65 properly filled ones. Based on the results of our survey, suitable design, printing and packaging specifications, necessary requirements, optimization of production planning and appropriate sewing machine setting are considered as the most important characteristics influencing the purchase of a clothing products.

  6. Numerical Investigation of Slab-Column Connection by Finite Element Method

    International Nuclear Information System (INIS)

    Akram, T.; Shaikh, M.A.; Memon, A.A.

    2007-01-01

    The flat slab-on-column construction subjected to high transverse stresses concentrated at the slab-column connection can lead to a non-ductile, sudden and brittle punching failure and results in the accidental collapse of flat slab buildings. The major parameters affecting the slab-column connection are the concrete strength, slab thickness, slab reinforcement and aspect ratio of column. The application of numerical methods based on the finite element theory for solving practical tasks allow to perform virtual testing of structures and explore their behavior under load and other effects in different conditions taking into account the elastic and plastic behavior of materials, appearance and development of cracks and other damages (disintegrations), and finally to simulate the failure mechanism and its consequences. In this study, the models are developed to carry out the finite element analysis of slab- column connection using ADINA (Automatic Dynamic Incremental Nonlinear Analysis) by varying the slab thickness and slab confining reinforcement and to investigate their effect on the deflection and load carrying capacity. Test results indicate that by increasing the slab thickness, the deflection and the load carrying capacity of slab-column connection increases, more over, by increasing the slab confining reinforcement, the deflection decreases where as the load carrying capacity increases. (author)

  7. Investigation of a pulsed current annealing method in reusing MOSFET dosimeters for in vivo IMRT dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Luo, Guang-Wen; Qi, Zhen-Yu, E-mail: qizhy@sysucc.org.cn; Deng, Xiao-Wu [Department of Radiation Oncology, Sun Yat-Sen University Cancer Center and State Key Laboratory of Oncology in Southern China, Collaborative Innovation Center of Cancer Medicine, Guangzhou 510060 (China); Rosenfeld, Anatoly [Centre for Medical Radiation Physics, University of Wollongong, Wollongong, NSW 2522 (Australia)

    2014-05-15

    Purpose: To explore the feasibility of pulsed current annealing in reusing metal oxide semiconductor field-effect transistor (MOSFET) dosimeters forin vivo intensity modulated radiation therapy (IMRT) dosimetry. Methods: Several MOSFETs were irradiated atd{sub max} using a 6 MV x-ray beam with 5 V on the gate and annealed with zero bias at room temperature. The percentage recovery of threshold voltage shift during multiple irradiation-annealing cycles was evaluated. Key dosimetry characteristics of the annealed MOSFET such as the dosimeter's sensitivity, reproducibility, dose linearity, and linearity of response within the dynamic range were investigated. The initial results of using the annealed MOSFETs for IMRT dosimetry practice were also presented. Results: More than 95% of threshold voltage shift can be recovered after 24-pulse current continuous annealing in 16 min. The mean sensitivity degradation was found to be 1.28%, ranging from 1.17% to 1.52%, during multiple annealing procedures. Other important characteristics of the annealed MOSFET remained nearly consistent before and after annealing. Our results showed there was no statistically significant difference between the annealed MOSFETs and their control samples in absolute dose measurements for IMRT QA (p = 0.99). The MOSFET measurements agreed with the ion chamber results on an average of 0.16% ± 0.64%. Conclusions: Pulsed current annealing provides a practical option for reusing MOSFETs to extend their operational lifetime. The current annealing circuit can be integrated into the reader, making the annealing procedure fully automatic.

  8. The use of classical and radionuclide methods to investigate soil erosion in the Beskidy Mts

    International Nuclear Information System (INIS)

    Froehlich, W.

    1997-01-01

    Information concerning the spatial patterns of erosion and deposition on cultivated hillslopes is difficult to obtain using conventional soil loss monitoring techniques. The use of the fallout radionuclides 134 Cs and 137 Cs as a sediment tracers offers considerable potential for elucidating patterns of soil redistribution. This paper presents the results of an investigation of soil erosion on a cultivate hillslope within the Homerka drainage basin in the Polish Flysch Carpathians, based on 134 Cs and 137 Cs measurements. The 137 Cs inventories of soils in this region reflect inputs from both bomb and Chernobyl-derived fallout. The high degree of spatial variability associated with Chernobyl fallout deposition poses considerable limitations on the potential for using radiocesium measurements to elucidate detailed patterns of soil loss. With an application of cesium method it was stated that during the last 35 years sediment storage within the edge of agricultural terraces is ca. 4 mm year -1 on the average on agricultural experimental slope in the drainage basin of Homerka. This value reflects tillage and dispersed wash and is comparable with the intensity of erosion on agricultural plots. The results provided by the 137 Cs measurements are consistent with other process-based measurements undertaken on the slopes and with available evidence concerning the dominant sources of suspended sediment transported by the local streams. A general model of soil loss and sediment delivery from cultivated slopes in the Polish Flysch Carpathians is proposed. (author)

  9. Investigation of oxygen vibrational relaxation by quasi-classical trajectory method

    International Nuclear Information System (INIS)

    Andrienko, Daniil; Boyd, Iain D.

    2015-01-01

    Highlights: • Importance of attraction for the O 2 –O energy exchange in hypersonic flows. • O 2 –O vibrational relaxation time cannot be described by the Millikan–White equation. • Weak dependence of exothermic transition rates on translational temperature. • Multiquantum jumps in molecular oxygen occur mostly via the exchange reaction. - Abstract: O 2 –O collisions are studied by the quasi-classical trajectory method. A full set of cross sections for the vibrational ladder is obtained utilizing an accurate O 3 potential energy surface. Vibrational relaxation is investigated at temperatures between 1000 and 10,000 K, that are relevant to hypersonic flows. The relaxation time is derived based on the removal rate for the first excited vibrational level. A significant deviation from the formula by Millikan and White is observed for temperatures beyond those reported in experimental work. Relaxation becomes less efficient at high temperatures, suggesting that the efficiency of the energy randomization is strongly to the attractive component of the O 3 potential energy surface. These results are explained by analyzing the microscopic parameter of collisions that reflects the number of exchanges in the shortest interatomic distance. The rates of exothermic transitions are found to be nearly independent of the translational temperature in the range of interest.

  10. Investigation of selection methods im mutation breeding of barley for protein quantity and quality

    International Nuclear Information System (INIS)

    Ulonska, E.; Gaul, H.; Baumer, M.; Gesellschaft fuer Strahlen- und Umweltforschung m.b.H., Gruenbach

    1975-01-01

    This mutation breeding programme is investigating the qualification of micro-mutations for the selection of improved protein quality and quantity. Normally, improvement of protein content in micro-mutations is rather small. Therefore, it is important to develop methods and conditions of selection being (a) capable of measuring these small deviations in protein content and quality, and (b) simple to use. In two experiments carried out in 1971 and 1972 nitrogen fertilization was found to be the most important factor in the improvement of selection conditions. There is a highly significant negative correlation between crude protein content and the standard deviation; i.e. the higher the content of crude protein, the lower the variation coefficient. This in turn leads to an increase of genetic variation necessary for better selection progress. Nitrogen fertilization, especially during ear emergence, covers environmental influences - e.g., planting space, sowing rate, growing in different plots (6, 3, 2, 1 rows or in half-ear hills) - to a great extent. Thus, by applying high doses of nitrogen dressings comparable results can be achieved. In an overall selection experiment (testing the entire crossing and mutation material available at Weihenstephan in a stepwise selection from 1971 to 1973) and two selection experiments conducted in 1971 to 1973 with micro-mutants - variety Nota, 4 times X-rayed and the naked barley strain 1606 treated once with EMS - significant selection results were found. (author)

  11. Investigation of a novel image segmentation method dedicated to forest fire applications

    Science.gov (United States)

    Rudz, S.; Chetehouna, K.; Hafiane, A.; Laurent, H.; Séro-Guillaume, O.

    2013-07-01

    To face fire it is crucial to understand its behaviour in order to maximize fighting means. To achieve this task, the development of a metrological tool is necessary for estimating both geometrical and physical parameters involved in forest fire modelling. A key parameter is to estimate fire positions accurately. In this paper an image processing tool especially dedicated to an accurate extraction of fire from an image is presented. In this work, the clustering on several colour spaces is investigated and it appears that the blue chrominance Cb from the YCbCr colour space is the most appropriate. As a consequence, a new segmentation algorithm dedicated to forest fire applications has been built using first an optimized k-means clustering in the Cb-channel and then some properties of fire pixels in the RGB colour space. Next, the performance of the proposed method is evaluated using three supervised evaluation criteria and then compared to other existing segmentation algorithms in the literature. Finally a conclusion is drawn, assessing the good behaviour of the developed algorithm. This paper is dedicated to the memory of Dr Olivier Séro-Guillaume (1950-2013), CNRS Research Director.

  12. Investigation of a pulsed current annealing method in reusing MOSFET dosimeters for in vivo IMRT dosimetry

    International Nuclear Information System (INIS)

    Luo, Guang-Wen; Qi, Zhen-Yu; Deng, Xiao-Wu; Rosenfeld, Anatoly

    2014-01-01

    Purpose: To explore the feasibility of pulsed current annealing in reusing metal oxide semiconductor field-effect transistor (MOSFET) dosimeters forin vivo intensity modulated radiation therapy (IMRT) dosimetry. Methods: Several MOSFETs were irradiated atd max using a 6 MV x-ray beam with 5 V on the gate and annealed with zero bias at room temperature. The percentage recovery of threshold voltage shift during multiple irradiation-annealing cycles was evaluated. Key dosimetry characteristics of the annealed MOSFET such as the dosimeter's sensitivity, reproducibility, dose linearity, and linearity of response within the dynamic range were investigated. The initial results of using the annealed MOSFETs for IMRT dosimetry practice were also presented. Results: More than 95% of threshold voltage shift can be recovered after 24-pulse current continuous annealing in 16 min. The mean sensitivity degradation was found to be 1.28%, ranging from 1.17% to 1.52%, during multiple annealing procedures. Other important characteristics of the annealed MOSFET remained nearly consistent before and after annealing. Our results showed there was no statistically significant difference between the annealed MOSFETs and their control samples in absolute dose measurements for IMRT QA (p = 0.99). The MOSFET measurements agreed with the ion chamber results on an average of 0.16% ± 0.64%. Conclusions: Pulsed current annealing provides a practical option for reusing MOSFETs to extend their operational lifetime. The current annealing circuit can be integrated into the reader, making the annealing procedure fully automatic

  13. The Application of Intensive Longitudinal Methods to Investigate Change: Stimulating the Field of Applied Family Research.

    Science.gov (United States)

    Bamberger, Katharine T

    2016-03-01

    The use of intensive longitudinal methods (ILM)-rapid in situ assessment at micro timescales-can be overlaid on RCTs and other study designs in applied family research. Particularly, when done as part of a multiple timescale design-in bursts over macro timescales-ILM can advance the study of the mechanisms and effects of family interventions and processes of family change. ILM confers measurement benefits in accurately assessing momentary and variable experiences and captures fine-grained dynamic pictures of time-ordered processes. Thus, ILM allows opportunities to investigate new research questions about intervention effects on within-subject (i.e., within-person, within-family) variability (i.e., dynamic constructs) and about the time-ordered change process that interventions induce in families and family members beginning with the first intervention session. This paper discusses the need and rationale for applying ILM to family intervention evaluation, new research questions that can be addressed with ILM, example research using ILM in the related fields of basic family research and the evaluation of individual-based interventions. Finally, the paper touches on practical challenges and considerations associated with ILM and points readers to resources for the application of ILM.

  14. Investigation of Methods for Selectively Reinforcing Aluminum and Aluminum-Lithium Materials

    Science.gov (United States)

    Bird, R. Keith; Alexa, Joel A.; Messick, Peter L.; Domack, Marcia S.; Wagner, John A.

    2013-01-01

    Several studies have indicated that selective reinforcement offers the potential to significantly improve the performance of metallic structures for aerospace applications. Applying high-strength, high-stiffness fibers to the high-stress regions of aluminum-based structures can increase the structural load-carrying capability and inhibit fatigue crack initiation and growth. This paper discusses an investigation into potential methods for applying reinforcing fibers onto the surface of aluminum and aluminum-lithium plate. Commercially-available alumina-fiber reinforced aluminum alloy tapes were used as the reinforcing material. Vacuum hot pressing was used to bond the reinforcing tape to aluminum alloy 2219 and aluminum-lithium alloy 2195 base plates. Static and cyclic three-point bend testing and metallurgical analysis were used to evaluate the enhancement of mechanical performance and the integrity of the bond between the tape and the base plate. The tests demonstrated an increase in specific bending stiffness. In addition, no issues with debonding of the reinforcing tape from the base plate during bend testing were observed. The increase in specific stiffness indicates that selectively-reinforced structures could be designed with the same performance capabilities as a conventional unreinforced structure but with lower mass.

  15. Investigation of Rock Failure Pattern in Creep by Digital Speckle Correlation Method

    Directory of Open Access Journals (Sweden)

    Yunliang Tan

    2013-01-01

    Full Text Available In order to study the mechanical characteristics from creep deformation to failure of rock, the tests of uniaxial compression and pushing steel-plate anchored in rock were performed, by using RLJW-2000 servo test synchronizing with Digital Speckle Correlation Method (DSCM. The investigations showed that for a uniaxial compressive specimen, when load arrived at 0.5σc, displacement clusters orderly formed, which was ahead of the macrocreep strain occurring in a slight jump mode when load arrived at 0.7σc. When the load level arrived at 0.8σc, displacement clusters gathered to be a narrow band. After that, the specimen abruptly fractured in a shear mode. In the creep pushing steel-plate test, when pushing force arrived at 25 kN, crack began to occur, the horizontal displacement field as well as shear strain field concentrated continuously along the interface between steel-plate and rock, and a new narrow concentrating band gathered in the upper layer. When pushing force arrived at 27.5 kN, another new narrow shear deformation band formed in the lower layer. Then, the steel-plate was pushed out quickly accompanying strong creep deformation.

  16. Computational methods for investigation of surface curvature effects on airfoil boundary layer behavior

    Directory of Open Access Journals (Sweden)

    Xiang Shen

    2017-03-01

    Full Text Available This article presents computational algorithms for the design, analysis, and optimization of airfoil aerodynamic performance. The prescribed surface curvature distribution blade design (CIRCLE method is applied to a symmetrical airfoil NACA0012 and a non-symmetrical airfoil E387 to remove their surface curvature and slope-of-curvature discontinuities. Computational fluid dynamics analysis is used to investigate the effects of curvature distribution on aerodynamic performance of the original and modified airfoils. An inviscid–viscid interaction scheme is introduced to predict the positions of laminar separation bubbles. The results are compared with experimental data obtained from tests on the original airfoil geometry. The computed aerodynamic advantages of the modified airfoils are analyzed in different operating conditions. The leading edge singularity of NACA0012 is removed and it is shown that the surface curvature discontinuity affects aerodynamic performance near the stalling angle of attack. The discontinuous slope-of-curvature distribution of E387 results in a larger laminar separation bubble at lower angles of attack and lower Reynolds numbers. It also affects the inherent performance of the airfoil at higher Reynolds numbers. It is shown that at relatively high angles of attack, a continuous slope-of-curvature distribution reduces the skin friction by suppressing both laminar and turbulent separation, and by delaying laminar-turbulent transition. It is concluded that the surface curvature distribution has significant effects on the boundary layer behavior and consequently an improved curvature distribution will lead to higher aerodynamic efficiency.

  17. Numerical investigations on flow dynamics of prismatic granular materials using the discrete element method

    Science.gov (United States)

    Hancock, W.; Weatherley, D.; Wruck, B.; Chitombo, G. P.

    2012-04-01

    The flow dynamics of granular materials is of broad interest in both the geosciences (e.g. landslides, fault zone evolution, and brecchia pipe formation) and many engineering disciplines (e.g chemical engineering, food sciences, pharmaceuticals and materials science). At the interface between natural and human-induced granular media flow, current underground mass-mining methods are trending towards the induced failure and subsequent gravitational flow of large volumes of broken rock, a method known as cave mining. Cave mining relies upon the undercutting of a large ore body, inducement of fragmentation of the rock and subsequent extraction of ore from below, via hopper-like outlets. Design of such mines currently relies upon a simplified kinematic theory of granular flow in hoppers, known as the ellipsoid theory of mass movement. This theory assumes that the zone of moving material grows as an ellipsoid above the outlet of the silo. The boundary of the movement zone is a shear band and internal to the movement zone, the granular material is assumed to have a uniformly high bulk porosity compared with surrounding stagnant regions. There is however, increasing anecdotal evidence and field measurements suggesting this theory fails to capture the full complexity of granular material flow within cave mines. Given the practical challenges obstructing direct measurement of movement both in laboratory experiments and in-situ, the Discrete Element Method (DEM [1]) is a popular alternative to investigate granular media flow. Small-scale DEM studies (c.f. [3] and references therein) have confirmed that movement within DEM silo flow models matches that predicted by ellipsoid theory, at least for mono-disperse granular material freely outflowing at a constant rate. A major draw-back of these small-scale DEM studies is that the initial bulk porosity of the simulated granular material is significantly higher than that of broken, prismatic rock. In this investigation, more

  18. The Netherlands XTC Toxicity (NeXT) study: objectives and methods of a study investigating causality, course, and clinical relevance

    NARCIS (Netherlands)

    de Win, Maartje M. L.; Jager, Gerry; Vervaeke, Hylke K. E.; Schilt, Thelma; Reneman, Liesbeth; Booij, Jan; Verhulst, Frank C.; den Heeten, Gerard J.; Ramsey, Nick F.; Korf, Dirk J.; van den Brink, Wim

    2005-01-01

    This paper describes the objectives and methods of The Netherlands XTC Toxicity (NeXT) study focussing on the causality, course, and clinical relevance of ecstasy neurotoxicity. Previous studies suggest that ecstasy (3,4 methylene-dioxymethamphetamine, MDMA, XTC) is toxic toward brain serotonin

  19. An Investigation into Novice English Teachers’ Beliefs about Method and Post-method Pedagogy in Turkish EFL Context

    Directory of Open Access Journals (Sweden)

    Mustafa Tekin

    2013-04-01

    Full Text Available This study which has a qualitative research design, reports on the views and beliefs of eleven novice English as a foreign language (EFL teachers about the English language teaching (ELT methods for the purpose of examining their knowledge about and attitudes towards popular methods and post-method as well as towards current discussions in ELT and the effects of them on their reported classroom practices. In this respect, the novice teachers were interviewed by means of the video conferencing feature of the Windows Live Messenger (currently SKYPE about their views and beliefs related to method vs. post-method discussions as well as their current teaching practices. The results revealed a discrepancy between the participants’ views and their classroom practices. In fact, the majority of the participants reported a negative change in their attitudes towards teaching after they started teaching. The majority of the eleven participants were totally unaware of the postmethod discussions. In the final section of the paper, the reasons for these findings are discussed in detail, and further suggestions are made in an attempt to find solutions to some of the problems reported by the participant novice teachers

  20. Underestimation of Severity of Previous Whiplash Injuries

    Science.gov (United States)

    Naqui, SZH; Lovell, SJ; Lovell, ME

    2008-01-01

    INTRODUCTION We noted a report that more significant symptoms may be expressed after second whiplash injuries by a suggested cumulative effect, including degeneration. We wondered if patients were underestimating the severity of their earlier injury. PATIENTS AND METHODS We studied recent medicolegal reports, to assess subjects with a second whiplash injury. They had been asked whether their earlier injury was worse, the same or lesser in severity. RESULTS From the study cohort, 101 patients (87%) felt that they had fully recovered from their first injury and 15 (13%) had not. Seventy-six subjects considered their first injury of lesser severity, 24 worse and 16 the same. Of the 24 that felt the violence of their first accident was worse, only 8 had worse symptoms, and 16 felt their symptoms were mainly the same or less than their symptoms from their second injury. Statistical analysis of the data revealed that the proportion of those claiming a difference who said the previous injury was lesser was 76% (95% CI 66–84%). The observed proportion with a lesser injury was considerably higher than the 50% anticipated. CONCLUSIONS We feel that subjects may underestimate the severity of an earlier injury and associated symptoms. Reasons for this may include secondary gain rather than any proposed cumulative effect. PMID:18201501

  1. Personality disorders in previously detained adolescent females: a prospective study

    NARCIS (Netherlands)

    Krabbendam, A.; Colins, O.F.; Doreleijers, T.A.H.; van der Molen, E.; Beekman, A.T.F.; Vermeiren, R.R.J.M.

    2015-01-01

    This longitudinal study investigated the predictive value of trauma and mental health problems for the development of antisocial personality disorder (ASPD) and borderline personality disorder (BPD) in previously detained women. The participants were 229 detained adolescent females who were assessed

  2. Investigation on n/γ discrimination methods for liquid scintillator detector

    International Nuclear Information System (INIS)

    Li Kuinian; Li Yang; Zhang Mei; Zhang Zhongbing; Li Binkang; Zhang Xiaodong; Liu Jun; Zhang Xianpeng

    2014-01-01

    To obtain the n/γ discrimination ability of different digital pulse shape discrimination methods, four methods (rising time method, charge comparison method, pulse gradient analysis and frequency gradient analysis) in americium-beryllium mixed radiation fields were demonstrated. The signals from EJ-301 and BC501A scintillator detectors were digitized using oscilloscope. A comparison was taken among the four discrimination methods. The discrimination results of the four methods in liquid scintillator detectors show that the rising time method is the best and it provides a good choice in real-time n/γ discrimination system. (authors)

  3. Advances in methods of commercial FBR core characteristics analyses. Investigations of a treatment of the double-heterogeneity and a method to calculate homogenized control rod cross sections

    Energy Technology Data Exchange (ETDEWEB)

    Sugino, Kazuteru [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center; Iwai, Takehiko

    1998-07-01

    A standard data base for FBR core nuclear design is under development in order to improve the accuracy of FBR design calculation. As a part of the development, we investigated an improved treatment of double-heterogeneity and a method to calculate homogenized control rod cross sections in a commercial reactor geometry, for the betterment of the analytical accuracy of commercial FBR core characteristics. As an improvement in the treatment of double-heterogeneity, we derived a new method (the direct method) and compared both this and conventional methods with continuous energy Monte-Carlo calculations. In addition, we investigated the applicability of the reaction rate ratio preservation method as a advanced method to calculate homogenized control rod cross sections. The present studies gave the following information: (1) An improved treatment of double-heterogeneity: for criticality the conventional method showed good agreement with Monte-Carlo result within one sigma standard deviation; the direct method was consistent with conventional one. Preliminary evaluation of effects in core characteristics other than criticality showed that the effect of sodium void reactivity (coolant reactivity) due to the double-heterogeneity was large. (2) An advanced method to calculate homogenize control rod cross sections: for control rod worths the reaction rate ratio preservation method agreed with those produced by the calculations with the control rod heterogeneity included in the core geometry; in Monju control rod worth analysis, the present method overestimated control rod worths by 1 to 2% compared with the conventional method, but these differences were caused by more accurate model in the present method and it is considered that this method is more reliable than the conventional one. These two methods investigated in this study can be directly applied to core characteristics other than criticality or control rod worth. Thus it is concluded that these methods will

  4. Computational Investigation of Novel Tip Leakage Mitigation Methods for High Pressure Turbine Blades

    Science.gov (United States)

    Ibrahim, Mounir; Gupta, Abhinav; Shyam, Vikram

    2014-01-01

    This paper presents preliminary findings on a possible approach to reducing tip leakage losses. In this paper a computational study was conducted on the Energy Efficient Engine (EEE) High Pressure Turbine (HPT) rotor tip geometry using the commercial numerical solver ANSYS FLUENT. The flow solver was validated against aerodynamic data acquired in the NASA Transonic Turbine Blade Cascade facility. The scope of the ongoing study is to computationally investigate how the tip leakage and overall blade losses are affected by (1) injection from the tip near the pressure side, (2) injection from the tip surface at the camber line, and (3) injection from the tip surface into the tip separation bubble. The objective is to identify the locations on the tip surface at which to place appropriately configured blowing keeping in mind the film cooling application of tip blowing holes. The validation was conducted at Reynolds numbers of 85,000, 343,000, and 685,000 and at engine realistic flow conditions. The coolant injection simulations were conducted at a Reynolds number of 343,000 based on blade chord and inlet velocity and utilized the SST turbulence model in FLUENT. The key parameters examined are the number of jets, jet angle and jet location. A coolant to inlet pressure ratio of 1.0 was studied for angles of +30 deg, -30 deg, and 90 deg to the local free stream on the tip. For the 3 hole configuration, 3 holes spaced 3 hole diameters apart with length to diameter ratio of 1.5 were used. A simulation including 11 holes along the entire mean camber line is also presented (30 deg toward suction side). In addition, the effect of a single hole is also compared to a flat tip with no injection. The results provide insight into tip flow control methods and can be used to guide further investigation into tip flow control. As noted in past research it is concluded that reducing leakage flow is not necessarily synonymous with reducing losses due to leakage.

  5. Alternative methods and radionuclides for use in soil-erosion and sedimentation investigations

    International Nuclear Information System (INIS)

    He, Q.; Walling, D.E.; Wallbrink, P.J.

    2002-01-01

    The use of 137 Cs for documenting rates and patterns of soil redistribution and sediment deposition represents an important advance that overcomes many of the limitations of existing techniques. Thus, the 137 Cs approach presents several key advantages but a number of potential limitations must also be recognized and addressed in any application. For example, traditional procedures for applying 137 Cs measurements in soil-erosion and sedimentation investigations involve the collection of soil or sediment cores from a study site and their subsequent transfer to the laboratory for preparation and analysis of 137 Cs activity by gamma spectrometry. The resulting measurements of 137 Cs activity (Bq g -1 ) are used to calculate the 137 Cs inventories (Bq m -2 ) for the individual cores and, thus the sampling points. In cases where a large number of cores are collected and require analysis, their processing and laboratory measurement will involve substantial effort. Furthermore, an extended period of time will generally be required for the measurements, because long count times are required for environmental samples containing relatively low levels of 137 Cs activity. Appreciable delays in obtaining results may, therefore, arise and it is not generally possible to obtain immediate data for use in planning and developing an ongoing sampling programme for detailed investigations. In view of these limitations, there is clearly a need to explore the potential for enhancing and extending the 137 Cs technique by using other methods to obtain the 137 Cs measurements within a shorter period of time and by using other fallout radionuclides with behaviour similar to that of 137 Cs but with a continuous input or a half-life extending to days rather than years, that could be used to document either the short-term contemporary rates of soil redistribution and sediment deposition or address issues of variability. This chapter discusses the procedures involved in employing field

  6. Preliminary investigation on welding and cutting methods for first wall support leg in ITER blanket module

    International Nuclear Information System (INIS)

    Mohri, Kensuke; Suzuki, Satoshi; Enoeda, Mikio; Kakudate, Satoshi; Shibanuma, Kiyoshi; Akiba, Masato

    2006-08-01

    Concept of a module type of blanket has been applied to ITER shield blanket, of which size is typically 1mW x 1mH x 0.4mB with the weight of 4 ton, in order to enhance its maintainability and fabricability. Each shield blanket module consists of a shield block and four first walls which are separable from the shield block for the purpose of reduction of an electro-magnetic force in disruption events, radio-active waste reduction in the maintenance work and cost reduction in fabrication process. A first wall support leg, a part of the first wall component located between the first wall and the shield block, is required not only to be connected metallurgically to the shield block in order to withstand the electro-magnetic force and coolant pressure, but also to be able to replace the first wall more than 2 times in the hot cell during the life time of the reactor. Therefore, the consistent structure where remote handling equipment can be access to the joint and carry out the welding/cutting works perfectly to replace the first wall in the hot cell is required in the shield blanket design. This study shows an investigation of the blanket module no.10 design with a new type of the first wall support leg structure based on Disc-Cutter technology, which had been developed for the main pipe cutting in the maintenance phase and was selected out of a number of candidate methods, taking its large advantages into account, such as 1) a post-treatment can be eliminated in the hot cell because of no making material chips and of no need of lubricant, 2) the cut surface can be rewelded without any machining. And also, a design for the small type of Disc-Cutter applied to the new blanket module no.10 has been investigated. In conclusion, not only the good performance of Disc-Cutter technology applied to the updated blanket module, but also consistent structure of the simplified shield blanket module including the first wall support leg in order to satisfy the requirements in the

  7. INVESTIGATION OF THE TOTAL ORGANIC HALOGEN ANALYTICAL METHOD AT THE WASTE SAMPLING AND CHARACTERIZATION FACILITY

    International Nuclear Information System (INIS)

    Douglas, J.G.; Meznarich, H.K.; Olsen, J.R.; Ross, G.A.; Stauffer, M.

    2009-01-01

    Total organic halogen (TOX) is used as a parameter to screen groundwater samples at the Hanford Site. Trending is done for each groundwater well, and changes in TOX and other screening parameters can lead to costly changes in the monitoring protocol. The Waste Sampling and Characterization Facility (WSCF) analyzes groundwater samples for TOX using the United States Environmental Protection Agency (EPA) SW-S46 method 9020B (EPA 1996a). Samples from the Soil and Groundwater Remediation Project (SGRP) are submitted to the WSCF for analysis without information regarding the source of the sample; each sample is in essence a ''blind'' sample to the laboratory. Feedback from the SGRP indicated that some of the WSCF-generated TOX data from groundwater wells had a number of outlier values based on the historical trends (Anastos 200Sa). Additionally, analysts at WSCF observed inconsistent TOX results among field sample replicates. Therefore, the WSCF lab performed an investigation of the TOX analysis to determine the cause of the outlier data points. Two causes were found that contributed to generating out-of-trend TOX data: (1) The presence of inorganic chloride in the groundwater samples: at inorganic chloride concentrations greater than about 10 parts per million (ppm), apparent TOX values increase with increasing chloride concentration. A parallel observation is the increase in apparent breakthrough of TOX from the first to the second activated-carbon adsorption tubes with increasing inorganic chloride concentration. (2) During the sample preparation step, excessive purging of the adsorption tubes with oxygen pressurization gas after sample loading may cause channeling in the activated carbon bed. This channeling leads to poor removal of inorganic chloride during the subsequent wash step with aqueous potassium nitrate. The presence of this residual inorganic chloride then produces erroneously high TOX values. Changes in sample preparation were studied to more effectively

  8. Investigation of the molecular relationship between breast cancer and obesity by candidate gene prioritization methods

    Directory of Open Access Journals (Sweden)

    Saba Garshasbi

    2015-10-01

    Full Text Available Background: Cancer and obesity are two major public health concerns. More than 12 million cases of cancer are reported annually. Many reports confirmed obesity as a risk factor for cancer. The molecular relationship between obesity and breast cancer has not been clear yet. The purpose of this study was to investigate priorities of effective genes in the molecular relationship between obesity and breast cancer. Methods: In this study, computer simulation method was used for prioritizing the genes that involved in the molecular links between obesity and breast cancer in laboratory of systems biology and bioinformatics (LBB, Tehran University, Tehran, Iran, from March to July 2014. In this study, ENDEAVOUR software was used for prioritizing the genes and integrating multiple data sources was used for data analysis. Training genes were selected from effective genes in obesity and/or breast cancer. Two groups of candidate genes were selected. The first group was included the existential genes in 5 common region chromosomes (between obesity and breast cancer and the second group was included the results of genes microarray data analysis of research Creighton, et al (In 2012 on patients with breast cancer. The microarray data were analyzed with GER2 software (R online software on GEO website. Finally, both training and candidate genes were entered in ENDEAVOUR software package. Results: The candidate genes were prioritized to four style and five genes in ten of the first priorities were repeated twice. In other word, the outcome of prioritizing of 72 genes (Product of microarray data analysis and genes of 5 common chromosome regions (Between obesity and breast cancer showed, 5 genes (TNFRSF10B, F2, IGFALS, NTRK3 and HSP90B1 were the priorities in the molecular connection between obesity and breast cancer. Conclusion: There are some common genes between breast cancer and obesity. So, molecular relationship is confirmed. In this study the possible effect

  9. [Investigation of new classification and repair methods for fingertip traverse amputation].

    Science.gov (United States)

    Zhou, Xiao; Xu, Yajun; Rui, Yongjun; Yao, Qun

    2008-09-01

    To investigate new classification and repair methods for the traverse amputated fingertip. From March 2000 to October 2006, 20 cases of 20 fingers with traverse amputated fingertip, including 13 males and 7 females aged 17-47 years, were treated. Twenty patients (9 crush injuries, 5 cutting injuries and 6 sawing injuries) were classified into 4 types, namely type I (the distal one third of nail bed), type II (the middle of nail bed), type III (the proximal one third of nail bed), and type IV (the root of nail bed). There were 3 patients (2 index fingers and 1 little finger) of type I, 8 patients (2 thumbs, 3 index fingers and 3 middle fingers) of type II, 5 patients (3 index fingers, 1 ring finger and 1 little finger) of type III, and 4 patients (2 thumbs, 1 middle finger and 1 little finger) of type IV. The soft tissue defect ranged from 1.2 cm x 1.2 cm to 1.5 cm x 1.2 cm. The time from injury to surgery was 3-10 hours. Fingers of type I and type II were treated with forward flow axial flap and modified nail bed lengthening. Fingers of type III and type IV were treated with forward flow axial flap and partial nail bed replantation as well as modified nail bed lengthening. The flaps ranged in size from 1.5 cm x 1.2 cm to 2.0 cm x 1.4 cm. Twenty patients incisions healed by first intention and the flaps, nails and skin grafting survived. All donor sites healed by first intention. All patients were followed up for 2-6 months (4 months on average). The appearances of fingertips were good. The texture of the flap was soft, and the fingers had no tenderness and motor disturbance. The two-point discrimination was 4.5-6.5 mm. The finger nails of type I and type II extended 3-4 mm after operation, while the finger nails of type III and type IV extended 8-10 mm after operation. All finger nails were smooth and flat without pain. Hook nail happened in 1 case 6 months after operation. Classification of the injured fingers according to the condition of the amputation base is

  10. Is Previous Respiratory Disease a Risk Factor for Lung Cancer?

    Science.gov (United States)

    Denholm, Rachel; Schüz, Joachim; Straif, Kurt; Stücker, Isabelle; Jöckel, Karl-Heinz; Brenner, Darren R.; De Matteis, Sara; Boffetta, Paolo; Guida, Florence; Brüske, Irene; Wichmann, Heinz-Erich; Landi, Maria Teresa; Caporaso, Neil; Siemiatycki, Jack; Ahrens, Wolfgang; Pohlabeln, Hermann; Zaridze, David; Field, John K.; McLaughlin, John; Demers, Paul; Szeszenia-Dabrowska, Neonila; Lissowska, Jolanta; Rudnai, Peter; Fabianova, Eleonora; Dumitru, Rodica Stanescu; Bencko, Vladimir; Foretova, Lenka; Janout, Vladimir; Kendzia, Benjamin; Peters, Susan; Behrens, Thomas; Vermeulen, Roel; Brüning, Thomas; Kromhout, Hans

    2014-01-01

    Rationale: Previous respiratory diseases have been associated with increased risk of lung cancer. Respiratory conditions often co-occur and few studies have investigated multiple conditions simultaneously. Objectives: Investigate lung cancer risk associated with chronic bronchitis, emphysema, tuberculosis, pneumonia, and asthma. Methods: The SYNERGY project pooled information on previous respiratory diseases from 12,739 case subjects and 14,945 control subjects from 7 case–control studies conducted in Europe and Canada. Multivariate logistic regression models were used to investigate the relationship between individual diseases adjusting for co-occurring conditions, and patterns of respiratory disease diagnoses and lung cancer. Analyses were stratified by sex, and adjusted for age, center, ever-employed in a high-risk occupation, education, smoking status, cigarette pack-years, and time since quitting smoking. Measurements and Main Results: Chronic bronchitis and emphysema were positively associated with lung cancer, after accounting for other respiratory diseases and smoking (e.g., in men: odds ratio [OR], 1.33; 95% confidence interval [CI], 1.20–1.48 and OR, 1.50; 95% CI, 1.21–1.87, respectively). A positive relationship was observed between lung cancer and pneumonia diagnosed 2 years or less before lung cancer (OR, 3.31; 95% CI, 2.33–4.70 for men), but not longer. Co-occurrence of chronic bronchitis and emphysema and/or pneumonia had a stronger positive association with lung cancer than chronic bronchitis “only.” Asthma had an inverse association with lung cancer, the association being stronger with an asthma diagnosis 5 years or more before lung cancer compared with shorter. Conclusions: Findings from this large international case–control consortium indicate that after accounting for co-occurring respiratory diseases, chronic bronchitis and emphysema continue to have a positive association with lung cancer. PMID:25054566

  11. Health care encounters in Danish chiropractic practice from a consumer perspectives - a mixed methods investigation.

    Science.gov (United States)

    Myburgh, Corrie; Boyle, Eleanor; Larsen, Johanne Brinch; Christensen, Henrik Wulff

    2016-01-01

    Perceived value is the key ingredient to carving and maintaining a competitive business niche. The opportunities to interact with consumers to understand and enhance perceived value are termed 'touch points'. Due to the out-of-pocket expense incurred by patients, Danish chiropractors are subject to consumer trends and behaviors. The purpose of this investigation was to explore and describe consumer touch points relevant to perceived value through healthcare journeys in chiropractic practices. We designed a convergent parallel, mixed methods study. Our purposive sampling framework identified 11 chiropractic clinics from which we collected observational field notes, video recordings and face-to-face interviews. Data was collected between April 14(th) and June 26(th) 2014. We described the exteriors and interiors of all participant clinics, interviewed 32 staff members, 12 new patients and 36 follow-up patients and finally video recorded 11 new and 24 follow-up consultations. Categorization and analysis led to the emergence six consumer touch point themes: 'the internet', 'the physical environment', 'practice models', 'administrative staff', 'the consultation sequence and timing' and 'a consultation that adds value'. The Internet functions as a tool when choosing/confirming a clinic as appropriate, developing and initial image and managing appointments. The administrative hub appears integral to the shaping of positive consumer experiences outside of the consultation. Clinic location, practice model and interior design may contribute to context effects and thus may influence value perception during the clinical encounter. The duration of hands-on treatment received from the chiropractor is not an apparent consumer focus point. Rather, through a seven stage clinical procedure patients value consultations with clinicians who demonstrate professional competence by effective communication diagnosis/management and facilitating satisfactory treatment outcomes. At least six

  12. Investigations on evaluation method for yield strength of round bar undermatched joint

    International Nuclear Information System (INIS)

    Matsumoto, Toshimi; Satoh, Hiroshi; Wadayama, Yoshihide

    1988-01-01

    The objective values of the yield strength and fracture toughness are respectively more than 1200 MPa and 200 MPa √m at 4K on the structural material for the superconducting magnet container in the Fusion Reactor. It should be desirable to assure the above value for the properties of the weld metal used for the containers. The initial yielding behavior of the undermatched joint is investigated in this paper. Results are as follows. (1) On the nominal stress vs. nominal strain relationship at the central section of the undermatched metal of the joint, the stress increases higher than the yield stress of undermatched metal itself then gradually comes up to a constant value, after the whole area of the undermatched metal starts to generate plastic deformation as the stress reaches the yield stress of the metal. (2) The increase in the stress is caused by the restraint effect of the base metal on the plasticity, and the stress becomes larger with the larger strength ratio of the undermatched metal to the basemetal and with the smaller relative thickness of the joint. (3) The strain does not distribute uniformly at the central section of the undermatched metal along the radial direction during the initial yielding process of the joint. (4) In the case that the yield strength of the joints is considered as the proof stress desided for a constant offset strain, the relationship between the dimensionless yield strength of the joint to the yield stress of the base metal and the relative yield strength of the undermatched metal to the base metal cannot be not established consistently. (5) The assumption that the base metal is rigid, causes the excessive evaluation of the joint yield strength of theoretical analysis. (6) As the quantitative evaluation method, the stress vs. strain relationship and then the algebraic expression has been formulated for the initial yielding behavior of the joint. (author)

  13. Uranium investigation in an alluvial aquifer with direct push methods - 59281

    International Nuclear Information System (INIS)

    De Weirdt, Fabian

    2012-01-01

    Document available in abstract form only. Full text of publication follows: The U.S. EPA has established a maximum contaminant level of 30 ug/l for uranium in drinking water due to its toxicity as a heavy metal. This regulation has affected many small public water supply systems in the US and several of them are struggling to come into compliance with the new standard. One such community is Clarks, NE, US which is situated on the alluvial deposits of the Platte River that are underlain by the Cretaceous Age Niobrara formation. Geoprobe Systems coordinated with the Nebraska Dept. of Health and Human Services, Water Well Stds. Program to investigate the cause of the elevated uranium in the groundwater that supplies drinking water to the village of Clarks. Initially hydraulic profiling tool (HPT) logs were obtained at selected locations across the Clarks well field. The HPT probe was advanced to depths of almost 36 m (120 ft) at several locations and the logs provided detailed information about the hydro-stratigraphy of the local aquifer not available from the drillers logs. The HPT logs were used to guide selection of screen depths for small diameter wells that were installed with direct push (DP) methods. A total of nine wells were installed at two locations at the facility with well depths ranging from as little as 6 m (20 ft) to a maximum of 36 m (118 ft). All wells were grouted bottom-up with a tremie tube using 25% solids bentonite slurry to assure screen interval isolation. (author)

  14. Investigation of Climate Change Impact on Salt Lake by Statistical Methods

    Directory of Open Access Journals (Sweden)

    Osman Orhan

    2017-03-01

    Full Text Available The main purpose of this paper is to investigate climate change impact that have been occurred on Salt Lake located in the central Anatolia is one of the area that has been faced to extinction. In order to monitor current status of the Salt Lake, Landsat satellite images has been obtained between the year of 2000 and 2014 (for the months of February, May, August and November. Satellite images has been processed by using ArcGIS and ERDAS softwares and the water surface area has been determined. The time series of water surface areas has been analyzed with auto-correlation method and repeated pattern has been detected. The seasonal part of the time series which period is 1 year and causes about 400 km² fluctuations has been removed with Moving Average filter, successfully. As a result of filtration process, non-seasonal time series of water surface area of Salt Lake were obtained. It is understood from the non-seasonal time series that the water surface area showed variability between 2000 and 2010 and after 2010 it is stable until 2014. In order to explain the variability, meteorological data (precipitation and temperature of the surrounding area has been acquired from the related service. The cross-correlation analyses has been performed with the movement of the water surface area and meteorological time series. As a result of analysis, the relationship between water surface changes in Salt Lake and meteorological data have correlated up to 80%. Consequently, several conclusion have been detected that the topography of the region play a direct role of the correlation coefficients and the water surface changes are effected from the environmental events that is occurred in the south of Salt Lake sub-Basin.

  15. Investigation of test methods, material properties, and processes for solar cell encapsulants. Annual report

    Energy Technology Data Exchange (ETDEWEB)

    Willis, P. B.; Baum, B.

    1979-06-01

    The goal of this program is to identify, evaluate, and recommend encapsulant materials and processes for the production of cost-effective, long-life solar cell modules. During the past year, the technical activities emphasized the reformulation of a commercial grade of ethylene/vinyl acetate copolymer for use as a pottant in solar cell module manufacture. After experimenting with a variety of techniques, a vacuum-bag process was developed and found to be an excellent encapsulation method. Adhesive strengths and primers for the bonding of ethylene/vinyl acetate to superstrate and substrate materials was assessed with encouraging results. The weathering effects on ten other polymers exposed to twelve months of weathering in Arizona, Florida, and under EMMAQUA were evaluated by determination of tensile strengths, elongations, optical transmission, etc. As may be expected, the best overall retention of mechanical properties is found for the fluorocarbon polymers, especially FEP. Hard coatings containing ultraviolet absorbers were investigated for the purpose of providing a soil resistant surface and additional weathering stability to the soft EVA pottant. Corrosion studies using a standard salt spray test were used to determine the degree of protection offered to a variety of metals by encapsulation in EVA pottant. A survey of scrim materials was also conducted. These open hole weaves are intended for use as spacers between the cell and substrate to provide a mechanical barrier, improve insulation resistance and prevent migration of the pigmented pottant over the cell surface. A mechanical engineering analysis of composite structural materials for use as substrates was performed. Results are presented in detail. (WHK)

  16. Regression methods to investigate the relationship between facial measurements and widths of the maxillary anterior teeth.

    Science.gov (United States)

    Isa, Zakiah Mohd; Tawfiq, Omar Farouq; Noor, Norliza Mohd; Shamsudheen, Mohd Iqbal; Rijal, Omar Mohd

    2010-03-01

    In rehabilitating edentulous patients, selecting appropriately sized teeth in the absence of preextraction records is problematic. The purpose of this study was to investigate the relationships between some facial dimensions and widths of the maxillary anterior teeth to potentially provide a guide for tooth selection. Sixty full dentate Malaysian adults (18-36 years) representing 2 ethnic groups (Malay and Chinese), with well aligned maxillary anterior teeth and minimal attrition, participated in this study. Standardized digital images of the face, viewed frontally, were recorded. Using image analyzing software, the images were used to determine the interpupillary distance (IPD), inner canthal distance (ICD), and interalar width (IA). Widths of the 6 maxillary anterior teeth were measured directly from casts of the subjects using digital calipers. Regression analyses were conducted to measure the strength of the associations between the variables (alpha=.10). The means (standard deviations) of IPD, IA, and ICD of the subjects were 62.28 (2.47), 39.36 (3.12), and 34.36 (2.15) mm, respectively. The mesiodistal diameters of the maxillary central incisors, lateral incisors, and canines were 8.54 (0.50), 7.09 (0.48), and 7.94 (0.40) mm, respectively. The width of the central incisors was highly correlated to the IPD (r=0.99), while the widths of the lateral incisors and canines were highly correlated to a combination of IPD and IA (r=0.99 and 0.94, respectively). Using regression methods, the widths of the anterior teeth within the population tested may be predicted by a combination of the facial dimensions studied. (c) 2010 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

  17. Verification study on technology for site investigation for geological disposal. Confirmation of the applicability of survey methods through establishing site descriptive models in accordance with stepwise investigation approach

    International Nuclear Information System (INIS)

    Kondo, Hirofumi; Suzuki, Koichi; Hasegawa, Takuma; Hamada, Takaomi; Yoshimura, Kimitaka

    2014-01-01

    The Yokosuka Demonstration and Validation Project, which uses the Yokosuka Central Research Institute of Electric Power Industry (CRIEPI) site, a Neogene sedimentary and coastal environment, has been conducted since the 2006 fiscal year as a cooperative research project between NUMO (Nuclear Waste Management Organization of Japan) and CRIEPI. The objectives of this project were to examine and refine the basic methodology of the investigation and assessment in accordance with the conditions of geological environment at each stage of investigations from the surface (Preliminary Investigation and the first half of Detailed Investigation conducted by NUMO) for high level radioactive waste geological disposal. Within investigation technologies at these early stages, a borehole survey is an important means of directly obtaining various properties of the deep geological environment. On the other hand, surface geophysical prospecting data provide information about the geological and resistivity structures at depth for planning borehole surveys. During the 2006-2009 fiscal years, a series of on-site surveys and tests, including borehole surveys of YDP-1 (depth: 350 m) and YDP-2 (depth: 500 m), were conducted in this test site. Furthermore, seismic surveys (including seismic reflection method) and electromagnetic surveys (including magnetotelluric method) were conducted within the expanded CRIEPI site in the 2010 fiscal year to obtain information about the geological structure, and the resistivity structure reflecting the distribution of the salt water/fresh water boundary, respectively, to a depth of over several hundred meters. The validity of existing survey and testing methods for stepwise investigations (from surface to borehole surveys) for obtaining properties of the geological environment (in various conditions relating to differences in the properties of the Miura and the Hayama Groups at this site) was confirmed through establishing site descriptive models based on

  18. A NOVEL INVESTIGATION IN BLASTING OPERATION MANAGEMENT USING DECISION MAKING METHODS

    Directory of Open Access Journals (Sweden)

    M. Yari

    2014-12-01

    Full Text Available Blasting is one of the most important operations in the mining projects. Inappropriate blasting pattern may lead to unwanted events such as poor fragmentation, back break, fly rock etc. and affect the whole operation physically and economically. In fact selecting of the most suitable pattern among previously performed patterns can be considered as a Multi Attribute Decision Making.

  19. An investigation into the bedrock depth in the Eskisehir Quaternary Basin (Turkey) using the microtremor method

    Science.gov (United States)

    Tün, M.; Pekkan, E.; Özel, O.; Guney, Y.

    2016-10-01

    Amplification can occur in a graben as a result of strong earthquake-induced ground motion. Thus, in seismic hazard and seismic site response studies, it is of the utmost importance to determine the geometry of the bedrock depth. The main objectives of this study were to determine the bedrock depth and map the depth-to-bedrock ratio for use in land use planning in regard to the mitigation of earthquake hazards in the Eskişehir Basin. The fundamental resonance frequencies (fr) of 318 investigation sites in the Eskişehir Basin were determined through case studies, and the 2-D S-wave velocity structure down to the bedrock depth was explored. Single-station microtremor data were collected from the 318 sites, as well as microtremor array data from nine sites, seismic reflection data from six sites, deep-drilling log data from three sites and shallow drilling log data from ten sites in the Eskişehir Graben. The fundamental resonance frequencies of the Eskişehir Basin sites were obtained from the microtremor data using the horizontal-to vertical (H/V) spectral ratio (HVSR) method. The phase velocities of the Rayleigh waves were estimated from the microtremor data using the spatial autocorrelation (SPAC) method. The fundamental resonance frequency range at the deepest point of the Eskişehir Basin was found to be 0.23-0.35 Hz. Based on the microtremor array measurements and the 2-D S-wave velocity profiles obtained using the SPAC method, a bedrock level with an average velocity of 1300 m s-1 was accepted as the bedrock depth limit in the region. The log data from a deep borehole and a seismic reflection cross-section of the basement rocks of the Eskişehir Basin were obtained and permitted a comparison of bedrock levels. Tests carried out using a multichannel walk-away technique permitted a seismic reflection cross-section to be obtained up to a depth of 1500-2000 m using an explosive energy source. The relationship between the fundamental resonance frequency in the

  20. Experimental methods of investigation of kinetics and dynamics of nuclear reactors

    International Nuclear Information System (INIS)

    Costa Oliveira, Jaime M.

    1969-03-01

    The author presents experimental methods used to study kinetic and dynamic properties of nuclear reactors. Kinetic methods aim at determining characteristic parameters of the behaviour in time of neutrons. Dynamic methods aim at establishing the relationships between the reactor behaviour and its internal and external causes (notably the measurement of transfer functions). The author proposes a classification with respect to the excitation type: periodic excitation (reactivity sinusoidal modulation, source sinusoidal modulation, periodic pulse excitation), non periodic excitation (reactivity monitoring, reactivity linear variation, reactivity variation according to any given law, removal of starting source), random excitation (random reactivity or source excitation), natural fluctuations (alpha-Rossi method, methods of reduced variance, probabilistic methods, correlation methods, spectral analysis method). He also addresses space and energy effects. Applications are reported for low power and power reactors

  1. The use of marine geophysical methods in Geo-Engineering investigations of Dams/ Barrages - a case study of Kosi Barrage

    Digital Repository Service at National Institute of Oceanography (India)

    Vora, K.H.; Naidu, P.D.

    Geophysical Methods in Geo-Engineering Investigations of Dams/ Barrages - A Case Study of Kosi Barrage INTRODUCTION KH. Vora* P. Divakar Naidu* Dams and barrages are such civil engineering structures where foundation is submerged. The impounded water column... etc. Some other on the spot observations using pole and other elementary probing methods are in vogue. However, usually such investigations would provide only a generalised picture based on isolated data. Advent of high technology, developed over...

  2. Nuclear-physical methods in macro- and microanalytical investigations of contamination with radionuclides at Semipalatinsk Nuclear Test Site

    International Nuclear Information System (INIS)

    Solodukhin, V.P.

    2005-01-01

    A complex of nuclear-physical methods developed in the Institute of Nuclear Physics of Kazakhstan National Nuclear Center for the investigations of the rate, character and peculiarities of contamination with radionuclides of the Semipalatinsk Nuclear Test Site (SNTS) is presented. The developed method combines both macroinvestigations (radionuclide analysis, NAA, XRFA, ESR- and NGR-spectroscopy) and microinvestigations (MS, micro-PIXE, electron microscopy). The results of the investigations at the main SNTS test sites 'Opytnoye pole' and 'Degelen' are presented. (author)

  3. An investigation on clinical, radiological and biochemical methods for assessing periodontitis activity

    International Nuclear Information System (INIS)

    Janssen, P.T.M.

    1987-01-01

    In order to recognize in which stage rapidly progressing destruction of periodontal ligament fibers occurs, a number of diagnostic methods are studied in this thesis. It turns out that the actual much utilized clinical methods can not be improved while radiological and biochemical diagnositic methods are much more promising. 106 refs.; 20 figs.; 36 tabs

  4. Investigating water productivity and economic efficiency of wheat-crop under different sowing methods

    International Nuclear Information System (INIS)

    Mirani, A.A.; Dahri, Z.H.

    2011-01-01

    This study was conducted at PARC's research station Kala Shah Kaku, Lahore, in order to calculate the water productivity and economic efficiency of wheat-crop under different sowing methods in a combined harvested paddy filed. The sowing methods were direct drilling with FMI Seeder, Zero tillage and conventional method. Data were collected during 2008-09. Wheat-yield was 2750 kg/ha, 2665 kg/ha and 2610 kg/ha for direct drilling with F MI Seeder, Zero tillage and conventional method, respectively. The direct drilling in heavy residue gave 5.4 % more yield than the conventional method and 3.2 % more yield than zero tillage. The zero tillage ensured 2.1% more yield than the conventional method. The net water applied as 323, 354, and 380 mm for direct drilling with FMI seeder, zero tillage and conventional methods respectively against the potential crop evapotranspiration of 383 mm. This indicates that the direct drilling of wheat-crop in heave rice stubbles saves 15% irrigation water as compared to conventional method and 8.8% over zero tillage. The zero tillage method saves 6.8 % of irrigation water over the conventional method. The water productivity was found to be 0.851 kg/m3. 0.753 kg/m/sup 3/ and 0.687 kg/m/sup 3/ for direct drilling with FMI Seeder, Zero tillage and conventional method respectively. This indicates that the direct drilling ensures 23.9% increase in water productivity over conventional method and 13.01% over zero tillage. The zero tillage gave 9.6% more water productivity than the conventional method. The costs of production for the three sowing methods were Rs. 39123/ha, Rs.43737/ha and Rs. 53047/ha for direct drilling, zero tillage and conventional method respectively. This indicates an overall saving of Rs. 13924/ha (26.2 %) by the direct drilling method as compared to the conventional method and Rs. 4613/ha (10.5%) over zero tillage method. The zero tillage saves Rs. 9319/ha (17.6 %) over the conventional method. Thus, the resource

  5. Preoperative screening: value of previous tests.

    Science.gov (United States)

    Macpherson, D S; Snow, R; Lofgren, R P

    1990-12-15

    To determine the frequency of tests done in the year before elective surgery that might substitute for preoperative screening tests and to determine the frequency of test results that change from a normal value to a value likely to alter perioperative management. Retrospective cohort analysis of computerized laboratory data (complete blood count, sodium, potassium, and creatinine levels, prothrombin time, and partial thromboplastin time). Urban tertiary care Veterans Affairs Hospital. Consecutive sample of 1109 patients who had elective surgery in 1988. At admission, 7549 preoperative tests were done, 47% of which duplicated tests performed in the previous year. Of 3096 previous results that were normal as defined by hospital reference range and done closest to the time of but before admission (median interval, 2 months), 13 (0.4%; 95% CI, 0.2% to 0.7%), repeat values were outside a range considered acceptable for surgery. Most of the abnormalities were predictable from the patient's history, and most were not noted in the medical record. Of 461 previous tests that were abnormal, 78 (17%; CI, 13% to 20%) repeat values at admission were outside a range considered acceptable for surgery (P less than 0.001, frequency of clinically important abnormalities of patients with normal previous results with those with abnormal previous results). Physicians evaluating patients preoperatively could safely substitute the previous test results analyzed in this study for preoperative screening tests if the previous tests are normal and no obvious indication for retesting is present.

  6. INVESTIGATION OF CEMENT CONCRETE CONGLOMERATE SOLIDIFICATION PROCESS BY IMPEDANCE SPECTROSCOPY METHOD

    Directory of Open Access Journals (Sweden)

    S. N. Bandarenka

    2015-01-01

    Full Text Available One of the most prospective directions in preservation  and increase of service live of  road pavements is a construction of  automobile roads with cement concrete surface. Modern tendencies for provision of road construction quality presuppose a necessity to control processes of solidification and subsequent destruction of the material while forming and using cement concrete conglomerate being considered as a basic element of the road surface.  Multiyear practical experience of  automobile road operation using cement concrete pavements reveals an importance for monitoring  such processes as formation and destruction of cement concrete materials. An impedance spectroscopy method has been tried out and proposed as a tool for solution of the given problem.Experimental samples of cement concrete have been prepared for execution of tests, graded silica sand and granite chippings with particle size from 0.63 to 2.5 mm have been used as a fine aggregate in the samples. Dependencies of resistance (impedance on AC-current frequency  have been studied for samples of various nature and granulometric composition. The Gamry  G300 potentiostat has been used for measurement of complex impedance value. A spectrum analysis and calculation of equivalent circuit parameters calculation have been carried out while using EIS Spectrum Analyzer program.Comparison of impedance spectra for the prepared cement concrete samples have made it possible to reveal tendencies in changing spectrum parameters during solidification and subsequent contact with moisture in respect of every type of the sample. An equivalent electrical circuit has been developed that  characterizes physical and chemical processes which are accompanied by charge transfer in cement concrete conglomerate. The paper demonstrates a possibility to use an impedance spectroscopy for solution of a number of actual problems in the field of cement concrete technology problems. Particularly, the problems

  7. [Suitable investigation method of exploration and suggestions for investigating Chinese materia medica resources from wetland and artificial water of Hongze Lake region].

    Science.gov (United States)

    Liu, Rui; Yan, Hui; Duan, Jin-Ao; Liu, Xing-Jian; Ren, Quan-Jin; Li, Hui-Wei; Bao, Bei-Hua; Zhang, Zhao-Hui

    2016-08-01

    According to the technology requirements of the fourth national survey of Chinese Materia Medica resources (pilot), suitable investigation method of exploration and suggestions for investigating Chinese Materia Medica resources was proposed based on the type of wetland and artificial water of Hongze Lake region. Environment of Hongze Lake and overview of wetland, present situation of ecology and vegetation and vegetation distribution were analyzed. Establishment of survey plan, selection of sample area and sample square and confirmation of representative water area survey plan were all suggested. The present study provide references for improving Chinese materia medica resources survey around Hongze Lake, and improving the technical specifications. It also provide references for investigating Chinese Materia Medica resources survey on similar ecological environment under the condition of artificial intervention. Copyright© by the Chinese Pharmaceutical Association.

  8. Coconut oil extraction by the traditional Java method : An investigation of its potential application in aqueous Jatropha oil extraction

    NARCIS (Netherlands)

    Marasabessy, Ahmad; Moeis, Maelita R.; Sanders, Johan P. M.; Weusthuis, Ruud A.

    A traditional Java method of coconut oil extraction assisted by paddy crabs was investigated to find out if crabs or crab-derived components can be used to extract oil from Jatropha curcas seed kernels. Using the traditional Java method the addition of crab paste liberated 54% w w(-1) oil from

  9. Coconut oil extraction by the Java method: An investigation of its potential application in aqueous Jatropha oil extraction

    NARCIS (Netherlands)

    Marasabessy, A.; Moeis, M.R.; Sanders, J.P.M.; Weusthuis, R.A.

    2010-01-01

    A traditional Java method of coconut oil extraction assisted by paddy crabs was investigated to find out if crabs or crab-derived components can be used to extract oil from Jatropha curcas seed kernels. Using the traditional Java method the addition of crab paste liberated 54% w w-1 oil from grated

  10. Investigating the Practices of Assessment Methods in Amharic Language Writing Skill Context: The Case of Selected Higher Education in Ethiopia

    Science.gov (United States)

    Tesfay, Hailay

    2017-01-01

    This study aims to investigate Ethiopian higher education Amharic language writing skills instructors' practices of Assessment Methods in writing skill context. It was also intended to look for their viewpoints about the practicality of implementing Assessment Methods in Amharic writing courses. In order to achieve the goals of this study,…

  11. Evaluation of pump pulsation in respirable size-selective sampling: Part III. Investigation of European standard methods.

    Science.gov (United States)

    Soo, Jhy-Charm; Lee, Eun Gyung; Lee, Larry A; Kashon, Michael L; Harper, Martin

    2014-10-01

    Lee et al. (Evaluation of pump pulsation in respirable size-selective sampling: part I. Pulsation measurements. Ann Occup Hyg 2014a;58:60-73) introduced an approach to measure pump pulsation (PP) using a real-world sampling train, while the European Standards (EN) (EN 1232-1997 and EN 12919-1999) suggest measuring PP using a resistor in place of the sampler. The goal of this study is to characterize PP according to both EN methods and to determine the relationship of PP between the published method (Lee et al., 2014a) and the EN methods. Additional test parameters were investigated to determine whether the test conditions suggested by the EN methods were appropriate for measuring pulsations. Experiments were conducted using a factorial combination of personal sampling pumps (six medium- and two high-volumetric flow rate pumps), back pressures (six medium- and seven high-flow rate pumps), resistors (two types), tubing lengths between a pump and resistor (60 and 90 cm), and different flow rates (2 and 2.5 l min(-1) for the medium- and 4.4, 10, and 11.2 l min(-1) for the high-flow rate pumps). The selection of sampling pumps and the ranges of back pressure were based on measurements obtained in the previous study (Lee et al., 2014a). Among six medium-flow rate pumps, only the Gilian5000 and the Apex IS conformed to the 10% criterion specified in EN 1232-1997. Although the AirChek XR5000 exceeded the 10% limit, the average PP (10.9%) was close to the criterion. One high-flow rate pump, the Legacy (PP=8.1%), conformed to the 10% criterion in EN 12919-1999, while the Elite12 did not (PP=18.3%). Conducting supplemental tests with additional test parameters beyond those used in the two subject EN standards did not strengthen the characterization of PPs. For the selected test conditions, a linear regression model [PPEN=0.014+0.375×PPNIOSH (adjusted R2=0.871)] was developed to determine the PP relationship between the published method (Lee et al., 2014a) and the EN methods

  12. Research methods in health: investigating health and health services. 4th edition

    OpenAIRE

    Bowling, Ann

    2014-01-01

    This bestselling book provides an accessible introduction to the concepts and practicalities of research methods in health and health services. This new edition has been extensively re-worked and expanded and now includes expanded coverage of: Qualitative methods Social research Evaluation methodology Mixed methods Secondary data analysis Literature reviewing and critical appraisal Evidence based practiceCovering all core methodologies in detail the book looks at the following kinds of health...

  13. The use of nuclear analytical methods in the investigation of objects of art and historical monuments

    International Nuclear Information System (INIS)

    Janovsky, I.

    2006-01-01

    Special nuclear analytical methods contribute significantly to the identification of the origin, manufacturing technology and/or authenticity of objects of art and historical monuments, Such methods primarily include variants of X-ray fluorescence analysis and activation analysis. The former enables non/destructive testing of materials, the latter features a high sensitivity. The article presents numerous examples of use of such methods especially in the Czech Republic (or former Czechoslovakia). (author)

  14. An investigation of methods for free-field comparison calibration of measurement microphones

    DEFF Research Database (Denmark)

    Barrera-Figueroa, Salvador; Moreno Pescador, Guillermo; Jacobsen, Finn

    2010-01-01

    Free-field comparison calibration of measurement microphones requires that a calibrated reference microphone and a test microphone are exposed to the same sound pressure in a free field. The output voltages of the microphones can be measured either sequentially or simultaneously. The sequential...... method requires the sound field to have good temporal stability. The simultaneous method requires instead that the sound pressure is the same in the positions where the microphones are placed. In this paper the results of the application of the two methods are compared. A third combined method...

  15. Investigating the efficacy of practical skill teaching: a pilot-study comparing three educational methods.

    Science.gov (United States)

    Maloney, Stephen; Storr, Michael; Paynter, Sophie; Morgan, Prue; Ilic, Dragan

    2013-03-01

    Effective education of practical skills can alter clinician behaviour, positively influence patient outcomes, and reduce the risk of patient harm. This study compares the efficacy of two innovative practical skill teaching methods, against a traditional teaching method. Year three pre-clinical physiotherapy students consented to participate in a randomised controlled trial, with concealed allocation and blinded participants and outcome assessment. Each of the three randomly allocated groups were exposed to a different practical skills teaching method (traditional, pre-recorded video tutorial or student self-video) for two specific practical skills during the semester. Clinical performance was assessed using an objective structured clinical examination (OSCE). The students were also administered a questionnaire to gain the participants level of satisfaction with the teaching method, and their perceptions of the teaching methods educational value. There were no significant differences in clinical performance between the three practical skill teaching methods as measured in the OSCE, or for student ratings of satisfaction. A significant difference existed between the methods for the student ratings of perceived educational value, with the teaching approaches of pre-recorded video tutorial and student self-video being rated higher than 'traditional' live tutoring. Alternative teaching methods to traditional live tutoring can produce equivalent learning outcomes when applied to the practical skill development of undergraduate health professional students. The use of alternative practical skill teaching methods may allow for greater flexibility for both staff and infrastructure resource allocation.

  16. Automatic electromagnetic valve for previous vacuum

    International Nuclear Information System (INIS)

    Granados, C. E.; Martin, F.

    1959-01-01

    A valve which permits the maintenance of an installation vacuum when electric current fails is described. It also lets the air in the previous vacuum bomb to prevent the oil ascending in the vacuum tubes. (Author)

  17. On a possible method of experimental investigation of proton decay modes

    International Nuclear Information System (INIS)

    Gulkanyan, H.R.; Pogosov, V.S.; Tamanyan, A.G.

    1982-01-01

    A detector for experimental investigation of proton decay modes is described. The detector represents a multiwire high pressure gas chamber, located in an underground cavity in a rock salt layer, analogous to known underground artificial depositories of fuel gas. It allows to identify decay particles and reaction kinematics at the amount of working gas of several dozens of kilotons and more required for the proton decay detection at the half-lifetime tau > 10 33 years and investigation of decay modes at tau 33 years. The detector also permits to investigate other exotic events such as a search for fractional charge particles, neutrino oscillations

  18. Water chemistry - Investigation of Methods to Improve Homing by Hatchery Salmon

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Investigate olfactory imprinting techniques that will improve homing by hatchery salmon to their hatchery of origin, and thereby reduce potential risks from these...

  19. Investigation of methods to prepare carbon foils and to determine their thicknesses

    International Nuclear Information System (INIS)

    Xu Guoji; Guan Shouren; Luo Xinghua; Meng Xiangjin

    1988-01-01

    The development and study of methods to prepare carbon foils and to determine their thicknesses are described. The methods of making carbon foils consist of carbon-arc evaporation, resistance heating, electron bombardment, cracking ethylene and centrifugal precipitation. Weighing, α-particle measurement, Rutherford backscattering and spectrophotometer are used to determine the thickness of carbon foils

  20. Discussion of the Investigation Method on the Reaction Kinetics of Metallurgical Reaction Engineering

    Science.gov (United States)

    Du, Ruiling; Wu, Keng; Zhang, Jiazhi; Zhao, Yong

    Reaction kinetics of metallurgical physical chemistry which was successfully applied in metallurgy (as ferrous metallurgy, non-ferrous metallurgy) became an important theoretical foundation for subject system of traditional metallurgy. Not only the research methods were very perfect, but also the independent structures and systems of it had been formed. One of the important tasks of metallurgical reaction engineering was the simulation of metallurgical process. And then, the mechanism of reaction process and the conversion time points of different control links should be obtained accurately. Therefore, the research methods and results of reaction kinetics in metallurgical physical chemistry were not very suitable for metallurgical reaction engineering. In order to provide the definite conditions of transmission, reaction kinetics parameters and the conversion time points of different control links for solving the transmission and reaction equations in metallurgical reaction engineering, a new method for researching kinetics mechanisms in metallurgical reaction engineering was proposed, which was named stepwise attempt method. Then the comparison of results between the two methods and the further development of stepwise attempt method were discussed in this paper. As a new research method for reaction kinetics in metallurgical reaction engineering, stepwise attempt method could not only satisfy the development of metallurgical reaction engineering, but also provide necessary guarantees for establishing its independent subject system.

  1. Investigating the Efficacy of Practical Skill Teaching: A Pilot-Study Comparing Three Educational Methods

    Science.gov (United States)

    Maloney, Stephen; Storr, Michael; Paynter, Sophie; Morgan, Prue; Ilic, Dragan

    2013-01-01

    Effective education of practical skills can alter clinician behaviour, positively influence patient outcomes, and reduce the risk of patient harm. This study compares the efficacy of two innovative practical skill teaching methods, against a traditional teaching method. Year three pre-clinical physiotherapy students consented to participate in a…

  2. Qualitative and quantitative methods for human factor analysis and assessment in NPP. Investigations and results

    International Nuclear Information System (INIS)

    Hristova, R.; Kalchev, B.; Atanasov, D.

    2005-01-01

    We consider here two basic groups of methods for analysis and assessment of the human factor in the NPP area and give some results from performed analyses as well. The human factor is the human interaction with the design equipment, with the working environment and takes into account the human capabilities and limits. In the frame of the qualitative methods for analysis of the human factor are considered concepts and structural methods for classifying of the information, connected with the human factor. Emphasize is given to the HPES method for human factor analysis in NPP. Methods for quantitative assessment of the human reliability are considered. These methods allow assigning of probabilities to the elements of the already structured information about human performance. This part includes overview of classical methods for human reliability assessment (HRA, THERP), and methods taking into account specific information about human capabilities and limits and about the man-machine interface (CHR, HEART, ATHEANA). Quantitative and qualitative results concerning human factor influence in the initiating events occurrences in the Kozloduy NPP are presented. (authors)

  3. Improved method for fibre content and quality analysis and their application to flax genetic diversity investigations

    NARCIS (Netherlands)

    Oever, van den M.J.A.; Bas, N.; Soest, van L.J.M.; Melis, C.; Dam, van J.E.G.

    2003-01-01

    Evaluation for fibre content and quality in a breeding selection program is time consuming and costly. Therefore, this study aims to develop a method for fast and reproducible fibre content analysis on small flax straw samples. A protocol has been developed and verified with fibre screening methods

  4. The Keyword Method of Foreign Vocabulary Learning: An Investigation of Its Generalizability. Working Paper No. 270.

    Science.gov (United States)

    Pressley, Michael; And Others

    In five experiments, college-age students of differing foreign language-learning abilities were asked to learn Latin word translations to determine the effectiveness of the keyword method of foreign language vocabulary learning. The Latin words were the types for which it has been argued that the keyword method effects would be maximized (the…

  5. An Investigation of Undefined Cut Scores with the Hofstee Standard-Setting Method

    Science.gov (United States)

    Wyse, Adam E.; Babcock, Ben

    2017-01-01

    This article provides an overview of the Hofstee standard-setting method and illustrates several situations where the Hofstee method will produce undefined cut scores. The situations where the cut scores will be undefined involve cases where the line segment derived from the Hofstee ratings does not intersect the score distribution curve based on…

  6. Fiscal 2000 report of investigation. International cooperative investigation on method for rationalizing use of energy; 2000 nendo energy shiyo gorika shuho kokusai kyoryoku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigative research was conducted for the purpose of building a database for LCA (life cycle assessment) that will be commonly used in Asian countries and developing an applicable environmental assessment methodology, with the fiscal 2000 results compiled. This year, joint researches and investigations were carried out with four countries, namely, Konkuk University (Korea), Taiwan Environmental Management Association (Taiwan), Universiti Putra Malaysia (Malaysia), and Thailand Environmental Institute (Thailand). The investigation covered the status how LCA problems were dealt with and how LCA infrastructures were built in the four countries. In the construction of the database for LCA, methods of preparing the LCA inventory database and their results were investigated concerning electrical power systems and production of basic materials (steel products), which were most important in implementing LCA in particular. In Thailand and Malaysia, lack of data for LCA was presumed; hence, necessary data sources were examined. Further, investigated also were the state of importing subterranean resources such as coal, oil, natural gas and iron ore, and the resource material flow or the like in each country. (NEDO)

  7. THE CBS SPECTRA INVESTIGATION AS METHOD OF THE PN CHEMICAL COMPOSITION ANALYSIS

    OpenAIRE

    Shimanskaya, N. N.; Shimansky, V. V.; Bikmaev, I. F.; Sakhibullin, N. A.; Zhuchkov, R. Ya.

    2007-01-01

    We report the results of the investigations of chemical composition of close binaries which had gone through the stage of common envelope and which are the remnants of planetary nebular cores. High resolution spectra for different phases of orbital period of V471 Tau were taken by RTT-150 telescope and were investigated by the modified SYNTH-K program. It was found that the spectra show noticeable variability with appearance of emission components depended on the orbital period phase. For che...

  8. Theoretical and numerical investigations into the SPRT method for anomaly detection

    Energy Technology Data Exchange (ETDEWEB)

    Schoonewelle, H.; Hagen, T.H.J.J. van der; Hoogenboom, J.E. [Interuniversitair Reactor Inst., Delft (Netherlands)

    1995-11-01

    The sequential probability ratio test developed by Wald is a powerful method of testing an alternative hypothesis against a null hypothesis. This makes the method applicable for anomaly detection. In this paper the method is used to detect a change of the standard deviation of a Gaussian distributed white noise signal. The false alarm probability, the alarm failure probability and the average time to alarm of the method, which are important parameters for anomaly detection, are determined by simulation and compared with theoretical results. Each of the three parameters is presented in dependence of the other two and the ratio of the standard deviation of the anomalous signal and that of the normal signal. Results show that the method is very well suited for anomaly detection. It can detect for example a 50% change in standard deviation within 1 second with a false alarm and alarm failure rate of less than once per month. (author).

  9. Investigation of Industrialised Building System Performance in Comparison to Conventional Construction Method

    Directory of Open Access Journals (Sweden)

    Othuman Mydin M.A.

    2014-03-01

    Full Text Available Conventional construction methods are still widely practised, although many researches have indicated that this method is less effective compared to the IBS construction method. The existence of the IBS has added to the many techniques within the construction industry. This study is aimed at making comparisons between the two construction approaches. Case studies were conducted at four sites in the state of Penang, Malaysia. Two projects were IBS-based while the remaining two deployed the conventional method of construction. Based on an analysis of the results, it can be concluded that the IBS approach has more to offer compared to the conventional method. Among these advantages are shorter construction periods, reduced overall costs, less labour needs, better site conditions and the production of higher quality components.

  10. An Investigation of Pulse Transit Time as a Non-Invasive Blood Pressure Measurement Method

    International Nuclear Information System (INIS)

    McCarthy, B M; O'Flynn, B; Mathewson, A

    2011-01-01

    The objective of this paper is to examine the Pulse Transit Method (PTT) as a non-invasive means to track Blood Pressure over a short period of time. PTT was measured as the time it takes for an ECG R-wave to propagate to the finger, where it is detected by a photoplethysmograph sensor. The PTT method is ideal for continuous 24-hour Blood Pressure Measurement (BPM) since it is both cuff-less and non-invasive and therefore comfortable and unobtrusive for the patient. Other techniques, such as the oscillometric method, have shown to be accurate and reliable but require a cuff for operation, making them unsuitable for long term monitoring. Although a relatively new technique, the PTT method has shown to be able to accurately track blood pressure changes over short periods of time, after which re-calibration is necessary. The purpose of this study is to determine the accuracy of the method.

  11. Theoretical and numerical investigations into the SPRT method for anomaly detection

    International Nuclear Information System (INIS)

    Schoonewelle, H.; Hagen, T.H.J.J. van der; Hoogenboom, J.E.

    1995-01-01

    The sequential probability ratio test developed by Wald is a powerful method of testing an alternative hypothesis against a null hypothesis. This makes the method applicable for anomaly detection. In this paper the method is used to detect a change of the standard deviation of a Gaussian distributed white noise signal. The false alarm probability, the alarm failure probability and the average time to alarm of the method, which are important parameters for anomaly detection, are determined by simulation and compared with theoretical results. Each of the three parameters is presented in dependence of the other two and the ratio of the standard deviation of the anomalous signal and that of the normal signal. Results show that the method is very well suited for anomaly detection. It can detect for example a 50% change in standard deviation within 1 second with a false alarm and alarm failure rate of less than once per month. (author)

  12. Investigation of a dual modal method for bone pathologies using quantitative ultrasound and photoacoustics

    Science.gov (United States)

    Steinberg, Idan; Gannot, Israel; Eyal, Avishay

    2015-03-01

    Osteoporosis is a widespread disease that has a catastrophic impact on patient's lives and overwhelming related healthcare costs. In recent works, we have developed a multi-spectral, frequency domain photoacoustic method for the evaluation of bone pathologies. This method has great advantages over pure ultrasonic or optical methods as it provides both molecular information from the bone absorption spectrum and bone mechanical status from the characteristics of the ultrasound propagation. These characteristics include both the Speed of Sound (SOS) and Broadband Ultrasonic Attenuation (BUA). To test the method's quantitative predictions, we have constructed a combined ultrasound and photoacoustic setup. Here, we experimentally present a dual modality system, and compares between the methods on bone samples in-vitro. The differences between the two modalities are shown to provide valuable insight into the bone structure and functional status.

  13. A comparative study to investigate burnup in research reactor fuel using two independent experimental methods

    International Nuclear Information System (INIS)

    Iqbal, M.; Mehmood, T.; Ayazuddin, S.K.; Salahuddin, A.; Pervez, S.

    2001-01-01

    Two independent experimental methods have been used for the comparative study of fuel burnup measurement in low enriched uranium, plate type research reactor. In the first method a gamma ray activity ratio method was employed. An experimental setup was established for gamma ray scanning using prior calibrated high purity germanium detector. The computer software KORIGEN gave the theoretical support. In the second method reactivity difference technique was used. At the same location in the same core configuration the fresh and burned fuel element's reactivity worth was estimated. For theoretical estimated curve, group cross-sections were generated using computer code WIMS-D/4, and three dimensional modeling was made by computer code CITATION. The measured burnup of different fuel elements using these methods were found to be in good agreement

  14. An Investigation of Science Teachers’ Teaching Methods and Techniques: Amasya Case

    Directory of Open Access Journals (Sweden)

    Orhan KARAMUSTAFAOĞLU

    2014-10-01

    Full Text Available The purpose of this study is to determine the methods and techniques science teachers mostly employ in their classrooms. To collect data, the researchers employed a survey with 60 science teachers and randomly selected 6 of them to observe these selected teachers in real classroom situation. Furthermore, the researchers invited 154 students taught by the selected 6 teachers in this study, for focus group interviewing. After analyzing the collected data, the researchers found that teachers in this study 1 were more likely to use narrative method, 2 supported their teaching with question and answer, demonstration, case study, and problem solving methods and techniques, and 3 rarely employed student centered discussion, laboratory practice, role playing and project-based learning methods in their classroom. Consequently, there exist some differences between theory and practice regarding teaching methods and techniques of teachers in this study.

  15. Radioisotopic methods of investigation in endocrinology. Radioizotopnye metody issledovaniya v endokrinologii

    Energy Technology Data Exchange (ETDEWEB)

    Malenchenko, A F; Matveenko, E G; Livshits, I B; Seregin, V V; Spesivtseva, V G

    1976-01-01

    A description is given of research on iodine metabolism both under normal and pathological conditions employing the method of clinical dynamic radiometry. Possible uses of radioisotopes are indicated for evaluating the function of the parathyroid glands, the pancreas, and the pituitary-adrenal system. Data are given on the practical use of radio-immune, radio-receptor methods as well as the competitive bonding method for determining a number of hormonal and other biologically active metabolites and substances with low antigen activity in various pathological states both clinically and in experiments. The use of neutron-activation methods in biology and medicine is demonstrated. The book is intended for endocrinologists, biologists, and scientific associates interested in the study of the functional state of endocrine glands by radioisotopic methods. 46 figures, 16 tables.

  16. A method for using unmanned aerial vehicles for emergency investigation of single geo-hazards and sample applications of this method

    Science.gov (United States)

    Huang, Haifeng; Long, Jingjing; Yi, Wu; Yi, Qinglin; Zhang, Guodong; Lei, Bangjun

    2017-11-01

    In recent years, unmanned aerial vehicles (UAVs) have become widely used in emergency investigations of major natural hazards over large areas; however, UAVs are less commonly employed to investigate single geo-hazards. Based on a number of successful investigations in the Three Gorges Reservoir area, China, a complete UAV-based method for performing emergency investigations of single geo-hazards is described. First, a customized UAV system that consists of a multi-rotor UAV subsystem, an aerial photography subsystem, a ground control subsystem and a ground surveillance subsystem is described in detail. The implementation process, which includes four steps, i.e., indoor preparation, site investigation, on-site fast processing and application, and indoor comprehensive processing and application, is then elaborated, and two investigation schemes, automatic and manual, that are used in the site investigation step are put forward. Moreover, some key techniques and methods - e.g., the layout and measurement of ground control points (GCPs), route planning, flight control and image collection, and the Structure from Motion (SfM) photogrammetry processing - are explained. Finally, three applications are given. Experience has shown that using UAVs for emergency investigation of single geo-hazards greatly reduces the time, intensity and risks associated with on-site work and provides valuable, high-accuracy, high-resolution information that supports emergency responses.

  17. Investigating the use of a rational Runge Kutta method for transport modelling

    Science.gov (United States)

    Dougherty, David E.

    An unconditionally stable explicit time integrator has recently been developed for parabolic systems of equations. This rational Runge Kutta (RRK) method, proposed by Wambecq 1 and Hairer 2, has been applied by Liu et al.3 to linear heat conduction problems in a time-partitioned solution context. An important practical question is whether the method has application for the solution of (nearly) hyperbolic equations as well. In this paper the RRK method is applied to a nonlinear heat conduction problem, the advection-diffusion equation, and the hyperbolic Buckley-Leverett problem. The method is, indeed, found to be unconditionally stable for the linear heat conduction problem and performs satisfactorily for the nonlinear heat flow case. A heuristic limitation on the utility of RRK for the advection-diffusion equation arises in the Courant number; for the second-order accurate one-step two-stage RRK method, a limiting Courant number of 2 applies. First order upwinding is not as effective when used with RRK as with Euler one-step methods. The method is found to perform poorly for the Buckley-Leverett problem.

  18. μ+-meson method of investigation of monocrystalline samples of ferromagnetic metals magnetized to saturation

    International Nuclear Information System (INIS)

    Gorelkin, V.N.; Miloserdin, V.Yu.; Smilga, V.P.

    1977-01-01

    Analysis and calculation have been performed with respect to local magnetic fields in nickel, cobalt and iron lattices with the use of the Ehwald's method. Based on the calculation results regularities have been established of the behaviour of muons in the given ferromagnetic materials in the absence of muon diffusion. It has been found that the μ + meson method makes it possible to study the position of a hydrogen light isotope (muonium) in the metal crystal lattice, deformation and stressed state of the lattice, to measure the contact and dipole fields. The advantages of the μ + meson method in the study of ferromagnetic properties are shown

  19. Study on Developments in Accident Investigation Methods: A Survey of the 'State-of-the-Art'

    Energy Technology Data Exchange (ETDEWEB)

    Hollnagel, Erik; Speziali, Josephine (Ecole des Mines de Paris, F-06904 Sophia Antipolis (France))

    2008-01-15

    The objective of this project was to survey the main accident investigation methods that have been developed since the early or mid-1990s. The motivation was the increasing frequency of accidents that defy explanations in simple terms, for instance cause-effect chains or 'human error'. Whereas the complexity of socio-technical systems is steadily growing across all industrial domains, including nuclear power production, accident investigation methods are only updated when their inability to account for novel types of accidents and incidents becomes inescapable. Accident investigation methods therefore typically lag behind the socio-technological developments by 20 years or more. The project first compiled a set of methods from the recognised scientific literature and in major major research and development programs, excluding methods limited to risk assessment, technological malfunctions, human reliability, and safety management methods. An initial set of 21 methods was further reduced to seven by retaining only prima facie accident investigation methods and avoiding overlapping or highly similar methods. The second step was to develop a set of criteria used to characterise the methods. The starting point was Perrow's description of normal accidents in socio-technical systems, which used the dimensions of coupling, going from loose to tight, and interactions, going from linear to complex. For practical reasons, the second dimension was changed to that of tractability or how easy it is to describe the system, where the sub-criteria are the level of detail, the availability of an articulated model, and the system dynamics. On this basis the seven selected methods were characterised in terms of the systems - or conditions - they could account for, leading to the following four groups: methods suitable for systems that are loosely coupled and tractable, methods suitable for systems that are tightly coupled and tractable, methods suitable for systems that

  20. Motivating factors for dual-method contraceptive use among adolescents and young women: a qualitative investigation.

    Science.gov (United States)

    Lemoine, Julie; Teal, Stephanie B; Peters, Marissa; Guiahi, Maryam

    2017-11-01

    This qualitative study explores how adolescents and young women perceive the need for and describe the use of dual method contraception. We interviewed 20 sexually active women aged 16-24 who attended an adolescent-focused Title X family-planning clinic and were using a non-barrier contraceptive method. We used a semi-structured interview guide that included domains related to sexual activity, knowledge of and use of contraceptives and condoms, and relationship factors. We coded transcripts using grounded theory techniques and used an iterative process to develop overarching themes. Dual method contraceptive users primarily discussed pregnancy prevention as their motivating factor. Many expressed anxieties over an unplanned pregnancy and reported condom use as "back-up" contraception. Risk perception for pregnancy or STI acquisition did not necessarily change as relationship trust increased, but rather, their anxiety regarding the negativity of such outcomes decreased. Dual-method contraception use decreased when participants reported that condoms were not readily available, or when they self-described immaturity. Less frequently, participants reported dual method use for sexually transmitted infection (STI) prevention, and many substituted STI testing for condom use. Contraceptive type (short-acting vs. long-acting) did not influence reported attitudes towards dual method use. Health educators and clinicians encourage condom use in young women due to the significant morbidity associated with STI acquisition. Most participants in our study view condoms as a way to improve pregnancy prevention. Acknowledging and addressing this divergence in motivation will allow caregivers to improve strategies for communicating the importance of dual method use. Young women primarily describe pregnancy prevention as the reason for dual method use, STI protection is less salient. Consideration of this viewpoint by health educators and clinicians will allow us to communicate more

  1. Investigation of adsorption properties of alumina produced by vacuum spray method

    International Nuclear Information System (INIS)

    Khrustaleva, K; Voronova, G

    2016-01-01

    In this paper nanopowders obtained by vacuum spray method were studied. The phase composition of the obtained powders is γ - Al 2 O 3 . Obtained nanopowders have specific surface area about 200 m 2 /g. Adsorptive properties of these powders were studied by static adsorption from solutions. The anionic dye eosin was selected as adsorbate. It has been found that the powders obtained by vacuum spray method have significant capacity to adsorb eosin. (paper)

  2. INVESTIGATION OF METHODS OF DNA EXTRACTION FROM PLANT ORIGIN OBJECTS AND FOODS BASED ON THEM

    Directory of Open Access Journals (Sweden)

    L. S. Dyshlyuk

    2014-01-01

    Full Text Available For the last decades modern and highly efficient methods of determining the quality and safety of food products, based on the application of the latest scientific achievements were developed in the world. A special place is given to the methods based on achievements of molecular biology and genetics. At the present stage of development in the field of assessing the quality of raw materials and processed food products much attention is given to highly accurate, sensitive and specific research methods, the method of polymerase chain reaction (PCR occupying a leading place among them. PCR is a sophisticated method that simulates the natural DNA replication and allows to detect a single specific DNA molecule in the presence of millions of other molecules. The key point in the preparation of material for PCR is the extraction of nucleic acids. The low content of DNA in plant material and the high concentration of secondary metabolites complicate the process of extraction. The key solution to this problem is highly effective method of extraction, which allows to obtain the DNA of adequate quality and purity. Comparative analysis of methods for the extraction of nucleic acids from fruit raw materials and products based on them was carried out in the study. General analysis of the experimental data allowed us to determine the most efficient method for DNA extracting. In the comparative analysis it was found out that to extract DNA from plant raw materials and food products prepared on their basis it is the most suitable to use "Sorb-GMO-A" reactants kit (set. The approach described gives us a brilliant opportunity to obtain deoxyribonucleic acid proper quality and purity.

  3. Investigation on method of estimating the excitation spectrum of vibration source

    International Nuclear Information System (INIS)

    Zhang Kun; Sun Lei; Lin Song

    2010-01-01

    In practical engineer area, it is hard to obtain the excitation spectrum of the auxiliary machines of nuclear reactor through direct measurement. To solve this problem, the general method of estimating the excitation spectrum of vibration source through indirect measurement is proposed. First, the dynamic transfer matrix between the virtual excitation points and the measure points is obtained through experiment. The matrix combined with the response spectrum at the measure points under practical work condition can be used to calculate the excitation spectrum acts on the virtual excitation points. Then a simplified method is proposed which is based on the assumption that the vibration machine can be regarded as rigid body. The method treats the centroid as the excitation point and the dynamic transfer matrix is derived by using the sub structure mobility synthesis method. Thus, the excitation spectrum can be obtained by the inverse of the transfer matrix combined with the response spectrum at the measure points. Based on the above method, a computing example is carried out to estimate the excitation spectrum acts on the centroid of a electrical pump. By comparing the input excitation and the estimated excitation, the reliability of this method is verified. (authors)

  4. Methods for dynamic investigations of surface-attached in vitro bacterial and fungal biofilms

    DEFF Research Database (Denmark)

    Sternberg, Claus; Bjarnsholt, Thomas; Shirtliff, Mark

    2014-01-01

    Three dynamic models for the investigation of in vitro biofilm formation are described in this chapter. In the 6-well plate assay presented here, the placing of the plate on a rotating platform provides shear, thereby making the system dynamic with respect to the static microtiter assay.The second...... reported model, especially suitable for harvesting high amounts of cells for transcriptomic or proteomic investigations, is based on numerous glass beads placed in a flask incubated with shaking on a rotating platform, thus increasing the surface area for biofilm formation. Finally, the flow-cell system...

  5. Investigation of Condensed Media in Weak Fields by the Method of Nuclear Magnetic Resonance

    Science.gov (United States)

    Davydov, V. V.; Myazin, N. S.; Dudkin, V. I.; Velichko, E. N.

    2018-05-01

    A compact design of a rapid-response nuclear magnetic spectrometer for investigation of condensed media in weak fields is reported. As a result of investigation of different condensed media, special features of recording a nuclear magnetic resonance (NMR) signal in a weak magnetic field from a small volume of the medium under study are established. For the first time the NMR absorption spectra of condensed media in a weak field are collected. Based on the results of experimental studies, the potential of using a compact NMR-spectrometer for condensed media monitoring in a rapid response mode is determined.

  6. Thermodynamic free energy methods to investigate shape transitions in bilayer membranes.

    Science.gov (United States)

    Ramakrishnan, N; Tourdot, Richard W; Radhakrishnan, Ravi

    2016-06-01

    The conformational free energy landscape of a system is a fundamental thermodynamic quantity of importance particularly in the study of soft matter and biological systems, in which the entropic contributions play a dominant role. While computational methods to delineate the free energy landscape are routinely used to analyze the relative stability of conformational states, to determine phase boundaries, and to compute ligand-receptor binding energies its use in problems involving the cell membrane is limited. Here, we present an overview of four different free energy methods to study morphological transitions in bilayer membranes, induced either by the action of curvature remodeling proteins or due to the application of external forces. Using a triangulated surface as a model for the cell membrane and using the framework of dynamical triangulation Monte Carlo, we have focused on the methods of Widom insertion, thermodynamic integration, Bennett acceptance scheme, and umbrella sampling and weighted histogram analysis. We have demonstrated how these methods can be employed in a variety of problems involving the cell membrane. Specifically, we have shown that the chemical potential, computed using Widom insertion, and the relative free energies, computed using thermodynamic integration and Bennett acceptance method, are excellent measures to study the transition from curvature sensing to curvature inducing behavior of membrane associated proteins. The umbrella sampling and WHAM analysis has been used to study the thermodynamics of tether formation in cell membranes and the quantitative predictions of the computational model are in excellent agreement with experimental measurements. Furthermore, we also present a method based on WHAM and thermodynamic integration to handle problems related to end-point-catastrophe that are common in most free energy methods.

  7. Investigation of cleaning and regeneration methods for reliable construction of DNA cantilever biosensors

    DEFF Research Database (Denmark)

    Quan, Xueling; Yi, Sun; Heiskanen, Arto

    to clean and regenerate the sensing surface of cantilever biosensors. Perchloric acid potential sweep, potassium hydroxide-hydrogen peroxide, and piranha cleaning are investigated here. Peak-current potential differences from cyclic voltammetry, X-ray photo-electron spectroscopy and fluorescence detection...

  8. Investigating the Limitations of Advanced Design Methods through Real World Application

    Science.gov (United States)

    2016-03-31

    36 War Room Laptop Display ( MySQL , JMP 9 Pro, 64-bit Windows) Georgia Tech Secure Collaborative Visualization Environment ( MySQL , JMP 9 Pro...investigate expanding the EA for VC3ATS • Would like to consider both an expansion of the use of current Java -based BPM approach and other potential EA

  9. Investigations of the surface conductivity of silicon dioxide and methods to reduce it

    NARCIS (Netherlands)

    Voorthuyzen, J.A.; Keskin, K.; Bergveld, Piet

    1987-01-01

    In this paper we describe our investigations of the electrical conductivity of the silicon dioxide-air interface. It appears that this conductivity is caused by the adsorption of water vapour on the oxide surface and strongly depends on the relative humidity of the surrounding air. Considering this

  10. A Mixed-Methods Investigation of Preservice Music Teaching Efficacy Beliefs and Commitment to Music Teaching

    Science.gov (United States)

    Prichard, Stephanie

    2017-01-01

    The purpose of this study was to investigate the music teaching efficacy beliefs and commitment to teaching of preservice music teachers enrolled in an introductory music education course. Also explored was the impact of introductory music education course experiences on preservice music teachers' music teaching efficacy beliefs and commitment to…

  11. Numerical investigation of thermally stratified Williamson fluid flow over a cylindrical surface via Keller box method

    Science.gov (United States)

    Bilal, S.; Rehman, Khalil Ur; Malik, M. Y.

    Present study is addressed to express the implementation of Keller-Box technique on physical problem in the field of fluid rheology, for this purpose the Williamson fluid flow is considered along a cylindrical stretching surface manifested with temperature stratification. The flow model is translated mathematically in terms of differential equations. Numerical simulation is executed to trace out the solution structure of developed differential system. The graphical outcomes for the flow regime of two different geometries (i-e cylindrical and plane surface) are reported and examined towards involved physical parameters. Furthermore, the local skin friction coefficient and local Nusselt number are computed numerically. A remarkable agreement of present study is noticed with the previously published results, which confirms the implementation and validation of Keller-Box scheme and it will serve as a helping source for the future correspondence.

  12. Thermodynamic properties of Mg2Si and Mg2Ge investigated by first principles method

    International Nuclear Information System (INIS)

    Wang, Hanfu; Jin, Hao; Chu, Weiguo; Guo, Yanjun

    2010-01-01

    The lattice dynamics and thermodynamic properties of Mg 2 Si and Mg 2 Ge are studied based on the first principles calculations. We obtain the phonon dispersion curves and phonon density of states spectra using the density functional perturbation theory with local density approximations. By employing the quasi-harmonic approximation, we calculate the temperature dependent Helmholtz free energy, bulk modulus, thermal expansion coefficient, specific heat, Debye temperature and overall Grueneisen coefficient. The results are in good agreement with available experimental data and previous theoretical studies. The thermal conductivities of both compounds are then estimated with the Slack's equation. By carefully choosing input parameters, especially the acoustic Debye temperature, we find that the calculated thermal conductivities agree fairly well with the experimental values above 80 K for both compounds. This demonstrates that the lattice thermal conductivity of simple cubic semiconductors may be estimated with satisfactory accuracy by combining the Slack's equation with the necessary thermodynamics parameters derived completely from the first principles calculations.

  13. Quality of life among dermatology patients: a systematic review of investigations using qualitative methods.

    Science.gov (United States)

    Singh, Sanminder; Ehsani-Chimeh, Nazanin; Kornmehl, Heather; Armstrong, April W

    2017-07-13

    Quality of life may be assessed using quantitative or qualitative methods. Quantitative methods are commonly used in research settings; however, they may fail to capture the full range of patient experiences and impact on quality of life. Qualitative methods may be used to address this limitation. In this systematic review, we aim to synthesize data from articles utilizing qualitative methods to assess quality of life in dermatology patients. We performed a systematic review search using the MEDLINE, EMBASE, and SCOPUS databases. The search was conducted using the following search criteria: ("Dermatology" [MeSH]) AND ("Quality of Life" [MeSH]), AND ("Qualitative Research" [MeSH]), searching literature spanning from January 1, 1946- October 5, 2016. The systematic review of 15 articles included 533 dermatology patients. Patients expressed frustration over the unpredictability of disease symptoms and having to compensate for the subsequent limitations by altering their daily routines. Patients also reported profound helplessness due to chronic skin disease and social isolation in an effort to hide their disease. Patients noted the patient-provider relationship as a source of support and information exchange, with the goal to form easy to use treatment plans that met both physician and patient expectations. Qualitative assessment of patient quality of life can provide new insights into the patient experience and the impact of their skin disease. Qualitative methodology may capture meaningful information that may be overlooked by quantitative methods, and it should be included in quality of life research.

  14. Investigations on the method of in vitro accumulation measurements of 14C phenylalanine on human small intestine biopsies, illustrated by the example of Diabetes mellitus

    International Nuclear Information System (INIS)

    Zenneck, A.

    1980-01-01

    A method was developed, by which actively transported substrates can accumulationarily be measured out in vitro on biopsy material. The applicability of this method as index for an active transport performance could then be examined on the example of a control group with sound small intestine and on patients with diabetes mellitus. In order to complete this parameter of the transport function, the specific saccharase activity in the overall homogenate of the mucous membrane was determined. The basis of this determination were the previous investigations on the experimental diabetes mellitus, in which morphologic and functional alterations had been detected. The various influences are discussed, which may be important for the detected alterations. However, a comparison with the results obtained in animal experiments is possible only to a very limited extent, since the situation in human diabetes mellitus is very complicated. (orig./MG) [de

  15. Methods of Investigation of Equations that Describe Waves in Tubes with Elastic Walls and Application of the Theory of Reversible and Weak Dissipative Shocks

    Science.gov (United States)

    Bakholdin, Igor

    2018-02-01

    Various models of a tube with elastic walls are investigated: with controlled pressure, filled with incompressible fluid, filled with compressible gas. The non-linear theory of hyperelasticity is applied. The walls of a tube are described with complete membrane model. It is proposed to use linear model of plate in order to take the bending resistance of walls into account. The walls of the tube were treated previously as inviscid and incompressible. Compressibility of material of walls and viscosity of material, either gas or liquid are considered. Equations are solved numerically. Three-layer time and space centered reversible numerical scheme and similar two-layer space reversible numerical scheme with approximation of time derivatives by Runge-Kutta method are used. A method of correction of numerical schemes by inclusion of terms with highorder derivatives is developed. Simplified hyperbolic equations are derived.

  16. Microtubules Nonlinear Models Dynamics Investigations through the exp(−Φ(ξ-Expansion Method Implementation

    Directory of Open Access Journals (Sweden)

    Nur Alam

    2016-02-01

    Full Text Available In this research article, we present exact solutions with parameters for two nonlinear model partial differential equations(PDEs describing microtubules, by implementing the exp(−Φ(ξ-Expansion Method. The considered models, describing highly nonlinear dynamics of microtubules, can be reduced to nonlinear ordinary differential equations. While the first PDE describes the longitudinal model of nonlinear dynamics of microtubules, the second one describes the nonlinear model of dynamics of radial dislocations in microtubules. The acquired solutions are then graphically presented, and their distinct properties are enumerated in respect to the corresponding dynamic behavior of the microtubules they model. Various patterns, including but not limited to regular, singular kink-like, as well as periodicity exhibiting ones, are detected. Being the method of choice herein, the exp(−Φ(ξ-Expansion Method not disappointing in the least, is found and declared highly efficient.

  17. The biospeckle method for the investigation of agricultural crops: A review

    Science.gov (United States)

    Zdunek, Artur; Adamiak, Anna; Pieczywek, Piotr M.; Kurenda, Andrzej

    2014-01-01

    Biospeckle is a nondestructive method for the evaluation of living objects. It has been applied to medicine, agriculture and microbiology for monitoring processes related to the movement of material particles. Recently, this method is extensively used for evaluation of quality of agricultural crops. In the case of botanical materials, the sources of apparent biospeckle activity are the Brownian motions and biological processes such as cyclosis, growth, transport, etc. Several different applications have been shown to monitor aging and maturation of samples, organ development and the detection and development of defects and diseases. This review will focus on three aspects: on the image analysis and mathematical methods for biospeckle activity evaluation, on published applications to botanical samples, with special attention to agricultural crops, and on interpretation of the phenomena from a biological point of view.

  18. An accelerated hybrid TLM-IE method for the investigation of shielding effectiveness

    Directory of Open Access Journals (Sweden)

    N. Fichtner

    2010-09-01

    Full Text Available A hybrid numerical technique combining time-domain integral equations (TD-IE with the transmission line matrix (TLM method is presented for the efficient modeling of transient wave phenomena. This hybrid method allows the full-wave modeling of circuits in the time-domain as well as the electromagnetic coupling of remote TLM subdomains using integral equations (IE. By using the integral equations the space between the TLM subdomains is not discretized and consequently doesn't contribute to the computational effort. The cost for the evaluation of the time-domain integral equations (TD-IE is further reduced using a suitable plane-wave representation of the source terms. The hybrid TD-IE/TLM method is applied in the computation of the shielding effectiveness (SE of metallic enclosures.

  19. Investigating Appropriate Financing Methods in Collaborative Projects of Water and Wastewater with AHP Approach

    Directory of Open Access Journals (Sweden)

    V. Vosoughi

    2017-10-01

    Full Text Available A mix of public and private funding is employed worldwide to enable the construction of large public projects and even, in some cases, the work of public services. In this study, the selected methods of financing of participatory projects of water and water wastes were studied and prioritized. Questionnaires and comments of experts were used along with AHP decision-making and Expert Choice software. Different financing methods include: BOT and BOO and its types, the publication of bonds, foreign direct investment, the method of buyback, internal financing, current financing, development banks, Barter transactions, new tax resources and foreign financing. Results are shown and discussed and a final ranking is provided.

  20. Investigation of Unbalanced Magnetic Force in Magnetic Geared Machine Using Analytical Methods

    DEFF Research Database (Denmark)

    Zhang, Xiaoxu; Liu, Xiao; Chen, Zhe

    2016-01-01

    The electromagnetic structure of the magnetic geared machine (MGM) may induce a significant unbalanced magnetic force (UMF). However, few methods have been developed to theoretically reveal the essential reasons for this issue in the MGM. In this paper, an analytical method based on an air....... Second, the magnetic field distribution in the MGM is modeled by an exact subdomain method, which allows the magnetic forces to be calculated quantitatively. The magnetic forces in two MGMs are then studied under no-load and full-load conditions. Finally, the finite-element calculation confirms......-gap relative permeance theory is first developed to qualitatively study the origins of the UMF in the MGM. By means of formula derivations, three kinds of magnetic field behaviors in the air gaps are found to be the potential sources of UMF. It is also proved that the UMF is possible to avoid by design choices...

  1. Investigation and analysis of the usefulness of the Zellik method to design energy conserving electric furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Szilagyi, L.; Fay, G.

    1984-01-01

    The characteristics predetermined by the method Zellik in designing the electrical furnaces isolated traditionally are comparable with measured values of furnaces in operation. The newest furnaces have been built with isolation resulting in a lower energy consumption. To plot the static characteristics, the furnace was heated up three times to the steady state. In determining the static heat capacity the stored heat was measured by the conventional method. With a view to determining the kinetic heat capacity the furnace was heated up at different rates. On the base of the operating results of the furnace can be stated both the practicability of the method Zellik and the improvement of the characteristics of the furnace isolated with fibrous material.

  2. Boundary layers affected by different pressure gradients investigated computationally by a zonal RANS-LES method

    International Nuclear Information System (INIS)

    Roidl, B.; Meinke, M.; Schröder, W.

    2014-01-01

    Highlights: • Reformulated synthetic turbulence generation method (RSTGM) is applied. • Zonal RANS-LES method is applied to boundary layers at pressure gradients. • Good agreement with the pure LES and other reference data is obtained. • The RSTGM is applicable to pressure gradient flows without modification. • RANS-to-LES boundary should be located where -1·10 6 6 is satisfied. -- Abstract: The reformulated synthetic turbulence generation (RSTG) method is used to compute by a fully coupled zonal RANS-LES approach turbulent non-zero-pressure gradient boundary layers. The quality of the RSTG method, which is based on the same shape functions and length scale distributions as in zero-pressure gradient flow, is discussed by comparing the zonal RANS-LES findings with pure LES, pure RANS, direct numerical simulation (DNS), and experimental data. For the favorable pressure gradient (FPG) simulation the RANS-to-LES transition occurs in the accelerated flow region and for the adverse pressure gradient (APG) case it is located in the decelerated flow region. The results of the time and spanwise averaged skin-friction distributions, velocity profiles, and Reynolds stress distributions of the zonal RANS-LES simulation show a satisfactory to good agreement with the pure LES, reference DNS, and experimental data. The quality of the findings shows that the rigorous formulation of the synthetic turbulence generation makes the RSTG method applicable without a priori knowledge of the flow properties but those determined by the RANS solution and without using additional control planes to regulate the shear stress budget to a wide range of Reynolds numbers and pressure gradients. The method is a promising approach to formulate embedded RANS-to-LES boundaries in flow regions where the Pohlhausen or acceleration parameter satisfies -1·10 -6 ⩽K⩽2·10 -6

  3. [A new method of investigation of "child's" behavior (infant-mother attachment) of newborn rats].

    Science.gov (United States)

    Stovolosov, I S; Dubynin, V A; Kamenskiĭ, A A

    2010-01-01

    A new method of studying "child's" (maternal bonding) behavior of newborn rats was developed. The efficiency of the method was proved in estimation of dopaminergic control of the infant-mother attachment. Selective D2-antagonist clebopride applied in subthreshold for motor activity doses caused a decrease in aspiration of pups to be in contact with a dam. On the basis of features analyzed (latent periods and expression of various behavioral components), the integrated criterion for the estimation of "child's" reactions was suggested. Application of this criterion made it possible to neutralize high individual variability of the behavior typical of newborns.

  4. Investigation of error estimation method of observational data and comparison method between numerical and observational results toward V and V of seismic simulation

    International Nuclear Information System (INIS)

    Suzuki, Yoshio; Kawakami, Yoshiaki; Nakajima, Norihiro

    2017-01-01

    The method to estimate errors included in observational data and the method to compare numerical results with observational results are investigated toward the verification and validation (V and V) of a seismic simulation. For the method to estimate errors, 144 literatures for the past 5 years (from the year 2010 to 2014) in the structure engineering field and earthquake engineering field where the description about acceleration data is frequent are surveyed. As a result, it is found that some processes to remove components regarded as errors from observational data are used in about 30% of those literatures. Errors are caused by the resolution, the linearity, the temperature coefficient for sensitivity, the temperature coefficient for zero shift, the transverse sensitivity, the seismometer property, the aliasing, and so on. Those processes can be exploited to estimate errors individually. For the method to compare numerical results with observational results, public materials of ASME V and V Symposium 2012-2015, their references, and above 144 literatures are surveyed. As a result, it is found that six methods have been mainly proposed in existing researches. Evaluating those methods using nine items, advantages and disadvantages for those methods are arranged. The method is not well established so that it is necessary to employ those methods by compensating disadvantages and/or to search for a solution to a novel method. (author)

  5. 77 FR 70176 - Previous Participation Certification

    Science.gov (United States)

    2012-11-23

    ... participants' previous participation in government programs and ensure that the past record is acceptable prior... information is designed to be 100 percent automated and digital submission of all data and certifications is... government programs and ensure that the past record is acceptable prior to granting approval to participate...

  6. On the Tengiz petroleum deposit previous study

    International Nuclear Information System (INIS)

    Nysangaliev, A.N.; Kuspangaliev, T.K.

    1997-01-01

    Tengiz petroleum deposit previous study is described. Some consideration about structure of productive formation, specific characteristic properties of petroleum-bearing collectors are presented. Recommendation on their detail study and using of experience on exploration and development of petroleum deposit which have analogy on most important geological and industrial parameters are given. (author)

  7. Subsequent pregnancy outcome after previous foetal death

    NARCIS (Netherlands)

    Nijkamp, J. W.; Korteweg, F. J.; Holm, J. P.; Timmer, A.; Erwich, J. J. H. M.; van Pampus, M. G.

    Objective: A history of foetal death is a risk factor for complications and foetal death in subsequent pregnancies as most previous risk factors remain present and an underlying cause of death may recur. The purpose of this study was to evaluate subsequent pregnancy outcome after foetal death and to

  8. Investigation of dental caries using laser and light-induced autofluorescence methods

    International Nuclear Information System (INIS)

    Borisova, E.; Avramov, L.; Uzunov, T.

    2006-01-01

    The aim of this study was to investigate the intrinsic fluorescence in human teeth in vitro and its correspondence to the stages of the carious lesions using different excitation sources. Fluorescence spectra of teeth illuminated with light with wavelengths of 337, 440 and 488 nm were recorded. The spectra were obtained from the healthy, pre-carious and carious stages of the teeth investigated. Fluorosa dentis and odontolithiasis lesions were also studied to determine the effect of other pathologies on the teeth fluorescence spectra. We observed a significant decrease of the autofluorescence signal intensity related to the carious stage. The carious samples also revealed characteristic emission with fluorescence bands in the red spectral region which relative peak intensity increases depending on the stage. Healthy hard dental tissue exhibited no emission bands in the long-wave region. (authors)

  9. Theoretical investigations of the new Cokriging method for variable-fidelity surrogate modeling

    DEFF Research Database (Denmark)

    Zimmermann, Ralf; Bertram, Anna

    2018-01-01

    Cokriging is a variable-fidelity surrogate modeling technique which emulates a target process based on the spatial correlation of sampled data of different levels of fidelity. In this work, we address two theoretical questions associated with the so-called new Cokriging method for variable fidelity...

  10. Experimental and mathematical modeling methods for the investigation of toxicological interactions

    International Nuclear Information System (INIS)

    El-Masri, Hisham A.

    2007-01-01

    While procedures have been developed and used for many years to assess risk and determine acceptable exposure levels to individual chemicals, most cases of environmental contamination can result in concurrent or sequential exposure to more than one chemical. Toxicological predictions of such combinations must be based on an understanding of the mechanisms of action and interaction of the components of the mixtures. Statistical and experimental methods test the existence of toxicological interactions in a mixture. However, these methods are limited to experimental data ranges for which they are derived, in addition to limitations caused by response differences from experimental animals to humans. Empirical methods such as isobolograms, median-effect principle and response surface methodology (RSM) are based on statistical experimental design and regression of data. For that reason, the predicted response surfaces can be used for extrapolation across dose regions where interaction mechanisms are not anticipated to change. In general, using these methods for predictions can be problematic without including biologically based mechanistic descriptions that can account for dose and species differences. Mechanistically based models, such as physiologically based pharmacokinetic/pharmacodynamic (PBPK/PD) models, include explicit descriptions of interaction mechanisms which are related to target tissues levels. These models include dose-dependent mechanistic hypotheses of toxicological interactions which can be tested by model-directed experimental design and used to identify dose regions where interactions are not significant

  11. Kinetic investigation of heterogeneous catalytic reactions by means of the kinetic isotope method

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, F; Dermietzel, J [Akademie der Wissenschaften der DDR, Leipzig. Zentralinstitut fuer Isotopen- und Strahlenforschung

    1978-09-01

    The application of the kinetic isotope method to heterogeneous catalytic processes is possible for surface compounds by using the steady-state relation. However, the characterization of intermediate products becomes ambiguous if sorption rates are of the same order of magnitude as surface reactions rates. The isotopic exchange reaction renders possible the estimation of sorption rates.

  12. Investigating the management of diabetes in nursing homes using a mixed methods approach.

    LENUS (Irish Health Repository)

    Hurley, L

    2017-03-21

    As populations age there is an increased demand for nursing home (NH) care and a parallel increase in the prevalence of diabetes. Despite this, there is growing evidence that the management of diabetes in NHs is suboptimal. The reasons for this are complex and poorly understood. This study aimed to identify the current level of diabetes care in NHs using a mixed methods approach.

  13. Investigating Environmentally Sustainable Transport Based on DALY weights and SIR Method

    Directory of Open Access Journals (Sweden)

    Hossein Nezamianpour Jahromi

    2012-09-01

    Full Text Available Accessibility is one of the main causes of well-being and growth in contemporary societies. Transportation is the backbone of accessibility systems that lead to the growth of economic and social networks and spatial dispersion of activities. Unfortunately, the adverse effects of transportation have a great impact on the natural and human environment. Since transportation is associated with fossil fuel combustion, it results in emissions of pollutants that cause damage to human health. To save the global eco-system, sustainable development has become an international priority. To deal with the sustainability of transportation systems is an important issue as testified by a growing number of initiatives framed to define and measure sustainability in transportation planning and infrastructure planning as well. The capability of environmental assessment as a sustainability instrument is well known. This study proposes a new approach to rank countries based on environmental sustainability development applying disability adjusted life year (DALY weights for transportation sector emissions. DALY weights consider actual impacts of pollutants on human health. By employing SIR method, a superiority and inferiority ranking method is presented for multiple criteria decision making, the sustainability ranking of a number of European countries is presented. Three various ranking methods extracted from SIR ranking method are discussed and the results and the correlation among them are demonstrated.

  14. Aspects of investigating scrambling in the synthesis of porphyrins Different analytical methods

    DEFF Research Database (Denmark)

    Nielsen, C.B.; Krebs, Frederik C

    2005-01-01

    Herein, we discuss the analyses and quantification of the different components in porphyrin mixtures, prepared from p-anisaidehyde, p-tolualdehyde, and 5-(4-bromophenyl)-dipyrromethane with acid catalysis, using NMR and HPLC. The advantages and disadvantages of these analytical methods are emphas...

  15. Investigation Into the Humaneness of Slaughter Methods for Guinea Pigs (Cavia porcelus) in the Andean Region.

    Science.gov (United States)

    Limon, Georgina; Gonzales-Gustavson, Eloy A; Gibson, Troy J

    2016-01-01

    Guinea pigs (Cavia porcelus) are an important source of nonhuman animal protein in the Andean region of South America. Specific guidelines regarding the welfare of guinea pigs before and during slaughter have yet to be developed. This study critically assessed the humaneness of 4 different stunning/slaughter methods for guinea pigs: cervical neck dislocation (n = 60), electrical head-only stunning (n = 83), carbon dioxide (CO2) stunning (n = 21), and penetrating captive bolt (n = 10). Following cervical neck dislocation, 97% of guinea pigs had at least 1 behavioral or cranial/spinal response. Six percent of guinea pigs were classified as mis-stunned after electrical stunning, and 1% were classified as mis-stunned after captive bolt. Increased respiratory effort was observed during CO2 stunning. Apart from this finding, there were no other obvious behavioral responses that could be associated with suffering. Of the methods assessed, captive bolt was deemed the most humane, effective, and practical method of stunning guinea pigs. Cervical neck dislocation should not be recommended as a slaughter method for guinea pigs.

  16. The investigation of the 2νββ decay by Pyatov method within ...

    Indian Academy of Sciences (India)

    elements is analysed. Keywords. Pyatov method; Gamow–Teller; quasiparticle random phase approximation;. 2νββ. PACS Nos 21.60.Cs; 23.40.-S. 1. Introduction. Nuclear double beta decay process is a rare transition in which the nuclear charge changes by two units as the mass number remains the same. This process ...

  17. La pronunciacion espanola y los metodos de investigacion. (Spanish Pronunciation and Methods of Investigation.)

    Science.gov (United States)

    Torreblanca, Maximo

    1988-01-01

    Discusses the validity of studies of Spanish pronunciation in terms of research methods employed. Topics include data collection in the laboratory vs. in a natural setting; recorded vs. non-recorded data; quality of the recording; aural analysis vs. spectrographic analysis; and transcriber reliability. Suggestions for improving data collection are…

  18. [Investigation of potential toxic factors for fleece-flower root: from perspective of processing methods evolution].

    Science.gov (United States)

    Cui, He-Rong; Bai, Zhao-Fang; Song, Hai-Bo; Jia, Tian-Zhu; Wang, Jia-Bo; Xiao, Xiao-He

    2016-01-01

    In recent years, the rapid growth of reports on fleece-flower root-caused liver damages has drawn wide attention of both at home and abroad, however, there were rare literature on toxicology of fleece-flower root in ancient Chinese medicine. But why there are so many reports on toxicology of fleece-flower root now compared with the ancient literature? As a typical tonic medicine, the clinical utility of fleece-flower root was largely limited by its standardization and reliability of processing methods in ancient Chinese medicine. The ancient processing methods of fleece-flower root emphasized nine times of steaming and nine times of drying, while the modern processes have been simplified into one time of steaming. Whether the differences between ancient and modern processing methods are the potential cause of the increased events of fleece-flower root-caused liver damages. We will make deep analysis and provide new clues and perspectives for the research on its toxicity. This article, therefore, would discuss the affecting factors and key problems in toxicity attenuation of fleece-flower root on the basis of sorting out the processing methods of fleece-flower root in ancient medical books and modern standards, in order to provide the reference for establishing specification for toxicity attenuation of fleece-flower root. Copyright© by the Chinese Pharmaceutical Association.

  19. Learning Financial Accounting in a Tertiary Institution of a Developing Country. An Investigation into Instructional Methods

    Science.gov (United States)

    Abeysekera, Indra

    2011-01-01

    This study examines three instructional methods (traditional, interactive, and group case-based study), and student opinions on their preference for learning financial accounting in large classes at a metropolitan university in Sri Lanka. It analyses the results of a survey questionnaire of students, using quantitative techniques to determine the…

  20. Children's Understanding of Advertising: An Investigation Using Verbal and Pictorially Cued Methods

    Science.gov (United States)

    Owen, Laura; Auty, Susan; Lewis, Charlie; Berridge, Damon

    2007-01-01

    Conflicting results on children's understanding of advertising may stem from differences in research methods. Most studies are conducted using interviewing techniques, employing only verbal questioning. In the present study, 136 children of two age groups (7 and 10 years) were first asked what advertising was for and, after responding, shown…

  1. Volume integral method for investigation of plasmonic nanowaveguide structures and photonic crystals

    Czech Academy of Sciences Publication Activity Database

    Lerer, A.M.; Donets, I.V.; Kalinchenko, Galina; Makhno, P.V.

    2014-01-01

    Roč. 2, č. 1 (2014), s. 31-37 ISSN 2327-9125 Grant - others:ELI Beamlines(XE) CZ.1.05/1.1.00/02.0061 Institutional support: RVO:68378271 Keywords : mathematical methods * subwavelength structures * nanostuctures Subject RIV: BH - Optics, Masers, Lasers

  2. All-union Conference. Principles and methods of regional and geochemical investigations into radionuclide migration

    International Nuclear Information System (INIS)

    Khitrov, L.M.

    1989-01-01

    The collection presents abstracts of papers concerning landscape-geochemical research of radionuclides migration; aspects of 'hot particles' study; radionuclides forms and behaviour in soils, in soil-plant; soil-natural water systems, as well as in water ecosystems. Methods of natural objects artificial radioactivity study are reviewed. Distribution of natural radionuclides in soils. natural waters, etc. is discussed

  3. Photon activation method to the investigation of bioobjects content for juridical-biological examination

    International Nuclear Information System (INIS)

    Dikiy, N.P.; Dyachenko, A.F.; Lyashko, Yu.V.; Medvedeva, E.P.; Uvarov, V.L.; Borovlev, V.I.

    2009-01-01

    Possibilities of the use of nuclear-physical methods for definition of element composition of biological objects (hair of animals) with the target of receipt of additional evidentiary information at the decision of diagnostics and identification problems within the limits of forensic-biological examination are shown

  4. A Multi-Method Investigation of Mathematics Motivation for Elementary Age Students

    Science.gov (United States)

    Linder, Sandra M.; Smart, Julie B.; Cribbs, Jennifer

    2015-01-01

    This paper presents the results of a multi-method study examining elementary students with high self-reported levels of mathematics motivation. Second- through fifth-grade students at a Title One school in the southeastern United States completed the Elementary Mathematics Motivation Instrument (EMMI), which examines levels of mathematics…

  5. An investigation into positron emission tomography contouring methods across two treatment planning systems

    International Nuclear Information System (INIS)

    Young, Tony; Som, Seu; Sathiakumar, Chithradevi; Holloway, Lois

    2013-01-01

    Positron emission tomography (PET) imaging has been used to provide additional information regarding patient tumor location, size, and staging for radiotherapy treatment planning purposes. This additional information reduces interobserver variability and produces more consistent contouring. It is well recognized that different contouring methodology for PET data results in different contoured volumes. The goal of this study was to compare the difference in PET contouring methods for 2 different treatment planning systems using a phantom dataset and a series of patient datasets. Contouring methodology was compared on the ADAC Pinnacle Treatment Planning System and the CMS XiO Treatment Planning System. Contours were completed on the phantom and patient datasets using a number of PET contouring methods—the standardized uptake value 2.5 method, 30%, 40%, and 50% of the maximum uptake method and the signal to background ratio method. Differences of >15% were observed for PET-contoured volumes between the different treatment planning systems for the same data and the same PET contouring methodology. Contoured volume differences between treatment planning systems were caused by differences in data formatting and display and the different contouring tools available. Differences in treatment planning system as well as contouring methodology should be considered carefully in dose-volume contouring and reporting, especially between centers that may use different treatment planning systems or those that have several different treatment planning systems

  6. New method of investigation of urine microflora in mice after irradiation

    Directory of Open Access Journals (Sweden)

    Ivanov A.A.

    2013-12-01

    nated with one drop of urine, placed on surface Endo media, incubate in thermostat (37°C in during 1-2 days and numbers of positive crops (Esch. coli, Proteus, Enterococcus, were indicated. It was shown that after irradiation the numbers of positive probes increased. The test displayed that the method is easy, economic and demonstrative.

  7. Creating Critical Conversations: Investigating the Utility of Socratic Dialogues in Elementary Social Studies Methods

    Science.gov (United States)

    Buchanan, Lisa Brown

    2012-01-01

    This article explores the utility of Socratic dialogues in the elementary social studies methods course. Findings include preservice teachers' behaviors during dialogues, perceived strengths and challenges of using Socratic dialogues in teacher education, and the impact on student learning. Challenges and apprehensions encountered by the teacher…

  8. Argon plasma jet continuum emission investigation by using different spectroscopic methods

    International Nuclear Information System (INIS)

    Dgheim, J

    2007-01-01

    Radiation and temperature fields of the continuum field are determined by using different spectroscopic methods based on the spectral emission of an argon plasma jet. An interferential filter of bandwidth 2.714 nm centred at a wavelength of 633 nm is used to observe only the continuum emission and to eliminate the self-absorption phenomenon. An optical multichannel analyser (OMA) of an MOS detector is used to measure argon plasma jet volumetric emissivity under atmospheric pressure and high temperatures. An emission spectroscopic method is used to measure the Stark broadening of the hydrogen line H β and to determine the electron density. The local thermodynamic equilibrium is established and its limit is stated. The local electron temperature is determined by two methods (the continuum emission relation and the LTE relations), and the total Biberman factor is measured. The results given by the OMA are compared with those given by the imagery method. At a given wavelength, the Biberman factor, which depends on the electron temperature and the electron density, may serve as an indicator to show where the LTE prevails along the argon plasma jet core length

  9. Development of a Mixed Methods Investigation of Process and Outcomes of Community-Based Participatory Research

    Science.gov (United States)

    Lucero, Julie; Wallerstein, Nina; Duran, Bonnie; Alegria, Margarita; Greene-Moton, Ella; Israel, Barbara; Kastelic, Sarah; Magarati, Maya; Oetzel, John; Pearson, Cynthia; Schulz, Amy; Villegas, Malia; White Hat, Emily R.

    2018-01-01

    This article describes a mixed methods study of community-based participatory research (CBPR) partnership practices and the links between these practices and changes in health status and disparities outcomes. Directed by a CBPR conceptual model and grounded in indigenous-transformative theory, our nation-wide, cross-site study showcases the value…

  10. A Mixed Methods Survey Research Study of Novice Special Education Teachers: Investigation of Reading Preparedness

    Science.gov (United States)

    Stratton, Mary P.

    2017-01-01

    Novice special education teachers have become an integral part of the public and private school systems throughout Pennsylvania. This mixed-methods research study explored the expertise and preparedness of current novice special education teachers. A combination of an electronic survey questionnaire and phone and face-to-face interviews were…

  11. Investigating Learning with an Interactive Tutorial: A Mixed-Methods Strategy

    Science.gov (United States)

    de Villiers, M. R.; Becker, Daphne

    2017-01-01

    From the perspective of parallel mixed-methods research, this paper describes interactivity research that employed usability-testing technology to analyse cognitive learning processes; personal learning styles and times; and errors-and-recovery of learners using an interactive e-learning tutorial called "Relations." "Relations"…

  12. Simulation-based investigation of the paired-gear method in cod-end selectivity studies

    DEFF Research Database (Denmark)

    Herrmann, Bent; Frandsen, Rikke; Holst, René

    2007-01-01

    In this paper, the paired-gear and covered cod-end methods for estimating the selectivity of trawl cod-ends are compared. A modified version of the cod-end selectivity simulator PRESEMO is used to simulate the data that would be collected from a paired-gear experiment where the test cod-end also ...

  13. Investigating issues influencing knowledge sharing in a research organization, using the Appreciative Inquiry Method

    OpenAIRE

    Hart, Penny

    2013-01-01

    This research contributes to the literature on the subjective experience of knowledge sharing from the perspective of those actively engaged in it. The sharing of knowledge in organizations is influenced by interconnecting factors, including organizational mission, the use made of information technology, and the motivation of individuals. Much of the existing literature takes a reductionist approach to investigating these, treating knowledge as an asset and humans as rational beings. A re...

  14. Electron accelerator with a laser ignition for investigation of beam plasma by optical methods

    International Nuclear Information System (INIS)

    Kabanov, S.N.; Korolev, A.A.; Kul'beda, V.E.; Razumovskij, A.I.; Trukhin, V.A.

    1990-01-01

    Facility to conduct investigations into dense gas beam plasma is described. Facility comprises: electron accelerator (200-300 keV, 5kA, 20ns), OGM-40 ignition ruby laser LZhI-501 diagnostic laser (with 0.55-0.66 μm tunable wave length), Michelson interferometer and diagnostic equipment for optical measurements. Laser ignition of spark gap is introduced to strong synchronization (±10ns) of radiation pulse of diagnostic laser with beam current pulse

  15. Investigation by the Rutherford backscattering method of impurity deposited on the T-3M tokamak diaphragm

    International Nuclear Information System (INIS)

    Danelyan, L.S.; Egorova, I.M.; Kulikauskas, V.S.; Baratov, D.G.; Belykh, T.A.

    1994-01-01

    The Rutherford backscattering of helium-4 ions was used for investigation of impurity deposited on the annular graphite diaphragm as a result of the interaction between hydrogen plasma and liquid-metal spray limiter. The experimental RBS spectra distributions of the impurity elements surface densities along the direction from plasma to the chamber wall are presented as depth of the elements. The erosion coefficient of the main liquid-metal limiter element has been estimated

  16. Investigation of gas discharge processes in PMTs by the autocorrelation method

    International Nuclear Information System (INIS)

    Morozov, V.A.; Morozova, N.V.

    2012-01-01

    The effect of the potential different at the focusing chamber electrodes of the FEU-85, FEU-87, and FEU-93 photomultipliers on the intensity of afterpulses resulting from gas discharge processes is investigated. With appropriately selected potentials, the number of recorded secondary pulses can be decreased. Charge distribution spectra are obtained for this sort of pulses, which gives a qualitative estimate of both the homogeneity of the charge and mass distribution of residual gases and the ion-electron emission coefficients

  17. Attitudes and Experiences of Close Interethnic Friendships Among Native Emerging Adults: A Mixed-Methods Investigation

    OpenAIRE

    Jones, Merrill L.

    2017-01-01

    This study included 114 Native adults and 6 Native/non-Native pairs of friends (age 18-25). Experiences and attitudes for close interethnic friendships were investigated. Friendship patterns and predictors were quantitatively assessed for the 114 Natives, with qualitative examination of the development and qualities of the six friend pairs. Results of quantitative analysis revealed that 80% of this sample reported friendship investment with Whites, and 55% reported friendship investment wi...

  18. Shrink properties of crosslinked polymers as investigated by a novel method

    International Nuclear Information System (INIS)

    Dobo, J.; Forgacs, P.; Somogyi, A.

    1981-01-01

    In the production and use of shrink materials, the slightly radiation crosslinked polymers are repeatedly heated above and cooled below their melting point, while maintained in extended state. Their shrink properties were investigated by model experiments simulating the thermal and mechanical influences. First an Instron testing apparatus has been used. In this paper, results obtained with a home-made electronic dynamometer with programmable extension and programmable temperature control are reported. (author)

  19. An Investigation of the Variety and Complexity of Statistical Methods Used in Current Internal Medicine Literature.

    Science.gov (United States)

    Narayanan, Roshni; Nugent, Rebecca; Nugent, Kenneth

    2015-10-01

    Accreditation Council for Graduate Medical Education guidelines require internal medicine residents to develop skills in the interpretation of medical literature and to understand the principles of research. A necessary component is the ability to understand the statistical methods used and their results, material that is not an in-depth focus of most medical school curricula and residency programs. Given the breadth and depth of the current medical literature and an increasing emphasis on complex, sophisticated statistical analyses, the statistical foundation and education necessary for residents are uncertain. We reviewed the statistical methods and terms used in 49 articles discussed at the journal club in the Department of Internal Medicine residency program at Texas Tech University between January 1, 2013 and June 30, 2013. We collected information on the study type and on the statistical methods used for summarizing and comparing samples, determining the relations between independent variables and dependent variables, and estimating models. We then identified the typical statistics education level at which each term or method is learned. A total of 14 articles came from the Journal of the American Medical Association Internal Medicine, 11 from the New England Journal of Medicine, 6 from the Annals of Internal Medicine, 5 from the Journal of the American Medical Association, and 13 from other journals. Twenty reported randomized controlled trials. Summary statistics included mean values (39 articles), category counts (38), and medians (28). Group comparisons were based on t tests (14 articles), χ2 tests (21), and nonparametric ranking tests (10). The relations between dependent and independent variables were analyzed with simple regression (6 articles), multivariate regression (11), and logistic regression (8). Nine studies reported odds ratios with 95% confidence intervals, and seven analyzed test performance using sensitivity and specificity calculations

  20. An investigation of methods for neutron dose measurement in high temperature irradiation fields

    Energy Technology Data Exchange (ETDEWEB)

    Kosako, Toshisou; Sugiura, Nobuyuki [Tokyo Univ. (Japan); Kudo, Kazuhiko [Kyushu Univ., Fukuoka (Japan)] [and others

    2000-10-01

    The Japan Atomic Energy Research Institute (JAERI) has been conducting the innovative basic research on high temperature since 1994, which is a series of high temperature irradiation studies using the High Temperature Engineering Test Reactor (HTTR). 'The Task Group for Evaluation of Irradiation Dose under High Temperature Radiation' was founded in the HTTR Utilization Research Committee, which is the promoting body of the innovative basic research. The present report is a summary of investigation which has been made by the Task Group on the present status and subjects of research and development of neutron detectors in high temperature irradiation fields, in view of contributing to high temperature irradiation research using the HTTR. Detectors investigated here in the domestic survey are the following five kinds of in-core detectors: 1) small fission counter, 2) small fission chamber, 3) self-powered detector, 4) activation detector, and 5) optical fiber. In addition, the research and development status in Russia has been investigated. The present report will also be useful as nuclear instrumentation of high temperature gas-cooled reactors. (author)

  1. Investigation of CFD calculation method of a centrifugal pump with unshrouded impeller

    Science.gov (United States)

    Wu, Dazhuan; Yang, Shuai; Xu, Binjie; Liu, Qiaoling; Wu, Peng; Wang, Leqin

    2014-03-01

    Currently, relatively large errors are found in numerical results in some low-specific-speed centrifugal pumps with unshrouded impeller because the effect of clearances and holes are not accurately modeled. Establishing an accurate analytical model to improve performance prediction accuracy is therefore necessary. In this paper, a three-dimensional numerical simulation is conducted to predict the performance of a low-specific-speed centrifugal pump, and the modeling, numerical scheme, and turbulent selection methods are discussed. The pump performance is tested in a model pump test bench, and flow rate, head, power and efficiency of the pump are obtained. The effect of taking into consideration the back-out vane passage, clearance, and balance holes is analyzed by comparing it with experimental results, and the performance prediction methods are validated by experiments. The analysis results show that the pump performance can be accurately predicted by the improved method. Ignoring the back-out vane passage in the calculation model of unshrouded impeller is found to generate better numerical results. Further, the calculation model with the clearances and balance holes can obviously enhance the numerical accuracy. The application of disconnect interface can reduce meshing difficulty but increase the calculation error at the off-design operating point at the same time. Compared with the standard k-ɛ, renormalization group k-ɛ, and Spalart-Allmars models, the Realizable k-ɛ model demonstrates the fastest convergent speed and the highest precision for the unshrouded impeller flow simulation. The proposed modeling and numerical simulation methods can improve the performance prediction accuracy of the low-specific-speed centrifugal pumps, and the modeling method is especially suitable for the centrifugal pump with unshrouded impeller.

  2. Investigations on detection sensitivity of the NRTA method for different size representing facilities. Pt. 1 and 2

    International Nuclear Information System (INIS)

    Gupta, D.; Bicking, U.; Koutsouvelis, G.

    1985-12-01

    The capability and limitations of the NRTA method (Near-Real-Time Accountancy method) in reprocessing facilities with different throughputs and inventories and measurement uncertainties, were investigated with a detailed computer simulated data base. These investigations have confirmed the earlier findings that the NRTA method could permit under certain operating conditions and for a number of realistic diversion scenarios, a perceptible improvement in the detection capability. Depending on the conditions prevailing, such improvements could be by a factor of 10-20, both for the detectable amounts and the detection time, over the conventional material balance method with annual inventories. The reasons for and the conditions which would permit such improvements have been discussed in detail with numerical examples in the report. (orig.) [de

  3. An overview on applied methods in the FRG to investigate human factors in control rooms of nuclear power plants

    International Nuclear Information System (INIS)

    Thomas, D.B.

    1985-01-01

    In the first half of 1984 a feasibility study was carried out with respect to the CSNI of the OECD/NEA inventory of methods for the analysis and evaluation of human factors in the control room of nuclear power plants. In order to enable an analysis of the methods to be made, an elementary categorization of the methods under field studies, laboratory studies and theoretical studies was performed. A further differentiation of these categories was used as the basis for a critical analysis and interpretation of the methods employed in the research plan. In the following sections, an explanation is given of the method categories used and the plans included in the investigation. A short representation is given of the breakdown of the applied methods into categories and an analysis is made of the results. Implications for research programs are discussed. (orig./GL) [de

  4. Investigation of the Use of Ecodesign Methods and Tools in the Electrical and Electronics Industries of Thailand

    OpenAIRE

    Samuelsson, Erik

    2008-01-01

    This investigation strives to determine the level of ecodesign awareness as well as to map the use of methods and tools for this concept in the electrical and electronics industries of Thailand. The foundation of the thesis is eight semi-structured qualitative research interviews performed with various people at Thai organisations, an electronics manufacturer in Thailand, and experts from Swedish, Danish and Thai universities. The research method has yielded the following results: The level o...

  5. Developing new methods to investigate nuclear physics input to the cosmological lithium problem

    Directory of Open Access Journals (Sweden)

    Cook K.J.

    2013-12-01

    Full Text Available A significant challenge to nuclear astrophysics is the cosmological lithium problem, where models of Big Bang nucleosynthesis indicate abundances of 7Li two to four times larger than what is inferred via spectroscopic measurements of metal-poor stars. Recent experimental techniques developed for nuclear reaction studies at energies near the fusion barrier, if extended to reactions of astrophysical interest, may help understand nuclear reactions that can affect the production of 7Li during the Big Bang. Experiments at the ANU, using new experimental techniques, have provided complete pictures of the breakup mechanisms of light nuclei in collisions with heavy targets, such as 208Pb and 209Bi [1]. These experiments revealed dominant breakup mechanisms which had not even been considered in theoretical models. The study of the breakup of 6Li and 7Li following interactions with 58,64Ni and 27Al acts as a stepping stone from this previous work towards future experimental studies of breakup reactions of astrophysical relevance. In all cases studied, breakup is dominantly triggered by nucleon transfer between the colliding partners, but the transfer mechanisms are different. The findings of these experiments and experimental considerations for extensions to reactions of light nuclei, such as d +7Be, will be presented.

  6. Numerical investigation of flows in Czochralski crystal growth by an axisymmetric lattice Boltzmann method

    Science.gov (United States)

    Peng, Y.; Shu, C.; Chew, Y. T.; Qiu, J.

    2003-03-01

    An alternative new method called lattice Boltzmann method (LBM) is applied in this work to simulate the flows in Czochralski crystal growth, which is one of the widely used prototypical systems for melt-crystal growth. The standard LBM can only be used in Cartesian coordinate system and we extend it to be applicable to this axisymmetric thermal flow problem, avoiding the use of three-dimensional LBM on Cartesian coordinate system. The extension is based on the following idea. By inserting position and time dependent source terms into the evolution equation of standard LBM, the continuity and NS equations on the cylindrical coordinate system [1] can be recovered. Our extension is validated by its application to the benchmark problem suggested by Wheeler [2].

  7. Methods of Experimental Investigation of Cavitation in a Convergent - Divergent Nozzle of Rectangular Cross Section

    Directory of Open Access Journals (Sweden)

    Jablonská Jana

    2016-08-01

    Full Text Available Cavitation is a phenomenon with both positive and negative effects and with dynamic manifestations in hydraulic, food, chemical and other machinery. This article deals with the detection and dynamic behavior of cavitation clouds in water flows through a rectangular cross-section convergent-divergent nozzle. Cavitation was measured by methods applicable in engineering practice. Pressure, flow rate, noise, vibration, and amount of air dissolved in the liquid were measured and cavitation region was recorded with a high-speed camera. Evaluation of acquired images in connection with measured pressure pulsations and mechanical vibrations was performed with the use of the FFT method. In certain cases, dimensionless parameters were used to generalize the measurements. The results will be used to specify multiphase mathematical cavitation model parameters.

  8. Numerical investigation of flows in Czochralski crystal growth by an axisymmetric lattice Boltzmann method

    International Nuclear Information System (INIS)

    Peng, Y.; Shu, C.; Chew, Y.T.; Qiu, J.

    2003-01-01

    An alternative new method called lattice Boltzmann method (LBM) is applied in this work to simulate the flows in Czochralski crystal growth, which is one of the widely used prototypical systems for melt-crystal growth. The standard LBM can only be used in Cartesian coordinate system and we extend it to be applicable to this axisymmetric thermal flow problem, avoiding the use of three-dimensional LBM on Cartesian coordinate system. The extension is based on the following idea. By inserting position and time dependent source terms into the evolution equation of standard LBM, the continuity and NS equations on the cylindrical coordinate system can be recovered. Our extension is validated by its application to the benchmark problem suggested by Wheeler

  9. First applications of structural pattern recognition methods to the investigation of specific physical phenomena at JET

    International Nuclear Information System (INIS)

    Ratta, G.A.; Vega, J.; Pereira, A.; Portas, A.; Luna, E. de la; Dormido-Canto, S.; Farias, G.; Dormido, R.; Sanchez, J.; Duro, N.; Vargas, H.; Santos, M.; Pajares, G.; Murari, A.

    2008-01-01

    Structural pattern recognition techniques allow the identification of plasma behaviours. Physical properties are encoded in the morphological structure of signals. Intelligent access methods have been applied to JET databases to retrieve data according to physical criteria. On the one hand, the structural form of signals has been used to develop general purpose data retrieval systems to search for both similar entire waveforms and similar structural shapes inside waveforms. On the other hand, domain dependent knowledge was added to the structural information of signals to create particular data retrieval methods for specific physical phenomena. The inclusion of explicit knowledge assists in data analysis. The latter has been applied in JET to look for first, cut-offs in ECE heterodyne radiometer signals and, second, L-H transitions

  10. First applications of structural pattern recognition methods to the investigation of specific physical phenomena at JET

    Energy Technology Data Exchange (ETDEWEB)

    Ratta, G.A. [Asociacion EURATOM/CIEMAT para Fusion (Spain)], E-mail: giuseppe.ratta@ciemat.es; Vega, J.; Pereira, A.; Portas, A.; Luna, E. de la [Asociacion EURATOM/CIEMAT para Fusion (Spain); Dormido-Canto, S.; Farias, G.; Dormido, R.; Sanchez, J.; Duro, N.; Vargas, H. [Dpto. Informatica y Automatica-UNED, 28040 Madrid (Spain); Santos, M.; Pajares, G. [Dpto. Arquitectura de Computadores y Automatica-UCM, 28040 Madrid (Spain); Murari, A. [Consorzio RFX-Associazione EURATOM ENEA per la Fusione, Padua (Italy)

    2008-04-15

    Structural pattern recognition techniques allow the identification of plasma behaviours. Physical properties are encoded in the morphological structure of signals. Intelligent access methods have been applied to JET databases to retrieve data according to physical criteria. On the one hand, the structural form of signals has been used to develop general purpose data retrieval systems to search for both similar entire waveforms and similar structural shapes inside waveforms. On the other hand, domain dependent knowledge was added to the structural information of signals to create particular data retrieval methods for specific physical phenomena. The inclusion of explicit knowledge assists in data analysis. The latter has been applied in JET to look for first, cut-offs in ECE heterodyne radiometer signals and, second, L-H transitions.

  11. Numerical investigation of flows in Czochralski crystal growth by an axisymmetric lattice Boltzmann method

    CERN Document Server

    Peng, Y; Chew, Y T; Qiu, J

    2003-01-01

    An alternative new method called lattice Boltzmann method (LBM) is applied in this work to simulate the flows in Czochralski crystal growth, which is one of the widely used prototypical systems for melt-crystal growth. The standard LBM can only be used in Cartesian coordinate system and we extend it to be applicable to this axisymmetric thermal flow problem, avoiding the use of three-dimensional LBM on Cartesian coordinate system. The extension is based on the following idea. By inserting position and time dependent source terms into the evolution equation of standard LBM, the continuity and NS equations on the cylindrical coordinate system can be recovered. Our extension is validated by its application to the benchmark problem suggested by Wheeler .

  12. Application of Time-Domain Electromagnetic Method in Investigating Saltwater Intrusion of Santiago Island (Cape Verde)

    Science.gov (United States)

    Gonçalves, Rui; Farzamian, Mohammad; Monteiro Santos, Fernando A.; Represas, Patrícia; Mota Gomes, A.; Lobo de Pina, A. F.; Almeida, Eugénio P.

    2017-11-01

    Santiago Island, the biggest and most populated island of the Cape Verde Republic, is characterised by limited surface waters and strong dependence on groundwater sources as the primary source of natural water supply for extensive agricultural activity and human use. However, as a consequence of the scarce precipitation and high evaporation as well as the intense overexploitation of the groundwater resources, the freshwater management is also in a delicate balance with saltwater at coastal areas. The time-domain electromagnetic (TDEM) method is used to locate the extent of saltwater intrusion in four important agricultural regions in Santiago Island; São Domingos, Santa Cruz, São Miguel, and Tarrafal. The application of this method in Santiago Island proves it to be a successful tool in imaging the fresh/saltwater interface location. Depths to the saline zones and extensions of saline water are mapped along eight TDEM profiles.

  13. Investigation of elements accumulation in some plants by nuclear-research methods

    International Nuclear Information System (INIS)

    Azhabov, A.K.; Khushmuradov, Sh.Kh.; Danilova, E.A.; Kist, A.A.; Dekhkanov, T.; Kobzev, A.P.; Muminov, I.T.

    2000-01-01

    The results of studies on 18 elements in the samples of hugh elecampane, middle-asian mint, field horsetail, mixed grass crop and turkestan dog rose fruits, collected at the two stationary sites A and B of the Bashkizylsaj area of the Chatkalsk biospheric reservation and studied through the neutron-activation (n), γ-activation (γ), X-ray spectral (p) and X-ray fluorescence (x) physical methods, are presented. The root-square errors of the results, obtained by different method and differences in the elements accumulation, depending on the plant type, their part and vegetation place, are evaluated. The coefficients of biological accumulation of 15 elements in the 15 plants under study are determined on the basis of the data on the elements content in plants and corresponding soil samples [ru

  14. Structural, vibrational and nuclear magnetic resonance investigations of 4-bromoisoquinoline by experimental and theoretical DFT methods.

    Science.gov (United States)

    Arjunan, V; Thillai Govindaraja, S; Jayapraksh, A; Mohan, S

    2013-04-15

    Quantum chemical calculations of energy, structural parameters and vibrational wavenumbers of 4-bromoisoquinoline (4BIQ) were carried out by using B3LYP method using 6-311++G(**), cc-pVTZ and LANL2DZ basis sets. The optimised geometrical parameters obtained by DFT calculations are in good agreement with electron diffraction data. Interpretations of the experimental FTIR and FT-Raman spectra have been reported with the aid of the theoretical wavenumbers. The differences between the observed and scaled wavenumber values of most of the fundamentals are very small. The thermodynamic parameters have also been computed. Electronic properties of the molecule were discussed through the molecular electrostatic potential surface, HOMO-LUMO energy gap and NBO analysis. To provide precise assignments of (1)H and (13)CNMR spectra, isotropic shielding and chemical shifts were calculated with the Gauge-Invariant Atomic Orbital (GIAO) method. Copyright © 2013 Elsevier B.V. All rights reserved.

  15. Investigation into the interaction of methylparaben and erythromycin with human serum albumin using multispectroscopic methods.

    Science.gov (United States)

    Naik, Keerti M; Nandibewoor, Sharanappa T

    2016-03-01

    In this paper, the interaction of methylparaben and erythromycin with human serum albumin (HSA) was studied for the first time using spectroscopic methods including Fourier transform infrared (FTIR) spectroscopy and UV absorption spectroscopy in combination with fluorescence quenching under physiological conditions. The binding parameters were evaluated using a fluorescence quenching method. Based on Förster's theory of non-radiation energy transfer, the binding average distance, r between the donor (HSA) and the acceptor (methylparaben and erythromycin) was evaluated. UV/vis absorption, FTIR, synchronous and 3D spectral results showed that the conformation of HSA was changed in the presence of methylparaben and erythromycin. The thermodynamic parameters were calculated according to the van't Hoff equation and are discussed. The effect of some biological metal ions and site probes on the binding of methylparaben and erythromycin to HSA were further examined. Copyright © 2015 John Wiley & Sons, Ltd.

  16. Investigating emotion recognition and empathy deficits in Conduct Disorder using behavioural and eye-tracking methods

    OpenAIRE

    Martin-Key, Nayra, Anna

    2017-01-01

    The aim of this thesis was to characterise the nature of the emotion recognition and empathy deficits observed in male and female adolescents with Conduct Disorder (CD) and varying levels of callous-unemotional (CU) traits. The first two experiments employed behavioural tasks with concurrent eye-tracking methods to explore the mechanisms underlying facial and body expression recognition deficits. Having CD and being male independently predicted poorer facial expression recognition across all ...

  17. Investigation of passivating films on Li-electrode by the method of photoelectronic emission

    International Nuclear Information System (INIS)

    Nimon, E.S.; Churikov, A.V.; Gamayunova, I.M.; L'vov, A.L.

    1995-01-01

    Spectral dependences of photoeffect under conditions of pulsed illumination by visible and near IR radiation of Li-electrode surface in propylene carbonate and thionyl chloride base solutions have been studied. Photoemission of electrons from lithium to passivating films on its surface is the primary stage of the cathode photoeffect detected. The method of electron photoemission is used to obtain information on the composition and characteristics of the passivating films. 21 refs., 7 figs., 1 tab

  18. An investigation of hydrogen storage methods for fuel cell operation with man-portable equipment

    Energy Technology Data Exchange (ETDEWEB)

    Browning, D [Defence Evaluation and Research Agency, Haslar (United Kingdom); Jones, P [Defence Evaluation and Research Agency, Haslar (United Kingdom); Packer, K [Defence Evaluation and Research Agency, Haslar (United Kingdom)

    1997-03-01

    Air breathing proton exchange membrane fuel cells (PEMFC) are being considered as a power source for man-portable equipment, such as army radios. In addition to the weight and volume of the fuel cell itself, the device producing hydrogen with which to fuel the cell is also of crucial importance. This paper describes a number of hydrogen storage methods and discusses their applicability to man-portable equipment. (orig.)

  19. Investigation of CoPd alloys by XPS and EPES using the pattern recognition method

    Czech Academy of Sciences Publication Activity Database

    Lesiak, B.; Zemek, Josef; Jiříček, Petr; Jozwik, A.

    2007-01-01

    Roč. 428, - (2007), s. 190-196 ISSN 0925-8388 R&D Projects: GA ČR GA202/06/0459 Institutional research plan: CEZ:AV0Z10100521 Keywords : CoPd alloys * x-ray photoelectron spectroscopy (XPS) * elastic peak electron spectroscopy (EPES) * pattern recognition method * fuzzy k-nearest neighbour rule (fkNN) * quantitative analysis * surface segregation Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.455, year: 2007

  20. Investigation of the existing methodology of value estimation and methods of discount rate estimation

    OpenAIRE

    Plikus, Iryna

    2017-01-01

    The subject of research is the current practice of determining the fair value of assets and liabilities at the present (discounted) cost. One of the most problematic places is the determination of the discount rate, which belongs to the jurisdiction of a professional accountant judgment.The methods of formalization, hypothetical assumption, system approach and scientific abstraction in substantiating the formation of accounting policy with respect to the choice of the discount rate are used i...