QUANTITATIVE EVALUATION METHOD OF ELEMENTS PRIORITY OF CARTOGRAPHIC GENERALIZATION BASED ON TAXI TRAJECTORY DATA

Directory of Open Access Journals (Sweden)

Z. Long

2017-09-01

Full Text Available Considering the lack of quantitative criteria for the selection of elements in cartographic generalization, this study divided the hotspot areas of passengers into parts at three levels, gave them different weights, and then classified the elements from the different hotspots. On this basis, a method was proposed to quantify the priority of elements selection. Subsequently, the quantitative priority of different cartographic elements was summarized based on this method. In cartographic generalization, the method can be preferred to select the significant elements and discard those that are relatively non-significant.

Prediction of polymer flooding performance using an analytical method

International Nuclear Information System (INIS)

Tan Czek Hoong; Mariyamni Awang; Foo Kok Wai

2001-01-01

The study investigated the applicability of an analytical method developed by El-Khatib in polymer flooding. Results from a simulator UTCHEM and experiments were compared with the El-Khatib prediction method. In general, by assuming a constant viscosity polymer injection, the method gave much higher recovery values than the simulation runs and the experiments. A modification of the method gave better correlation, albeit only oil production. Investigation is continuing on modifying the method so that a better overall fit can be obtained for polymer flooding. (Author)

Significance tests in mutagen screening: another method considering historical control frequencies

International Nuclear Information System (INIS)

Traut, H.

1983-01-01

Recently a method has been devised for testing the significance of the difference between a mutation frequency observed after chemical treatment or iradiation and the historical ('stable') control frequency. Another test is proposed serving the same purpose. Both methods are applied to several examples (experimental frequency versus historical control frequency). The results (P values) obtained agree well. (author)

Assessment of significance of features acquired from thyroid ultrasonograms in Hashimoto's disease

Directory of Open Access Journals (Sweden)

Koprowski Robert

2012-08-01

Full Text Available Abstract Introduction This paper concerns the analysis of the features obtained from thyroid ultrasound images in left and right transverse and longitudinal sections. In the image analysis, the thyroid lobe is treated as a texture for healthy subjects and patients with Hashimoto’s disease. The applied methods of analysis and image processing were profiled to obtain 10 features of the image. Then, their significance in the classification was shown. Material In this study, the examined group consisted of 29 healthy subjects aged 18 to 60 and 65 patients with Hashimoto's disease. For each subject, four ultrasound images were taken. They were all in transverse and longitudinal sections of the right and left lobe of the thyroid, which gave 376 images in total. Method 10 different features obtained from each ultrasound image were suggested. The analyzed thyroid lobe was marked automatically or manually with a rectangular element. Results The analysis of 10 features and the creation for each one of them their own decision tree configuration resulted in distinguishing 3 most significant features. The results of the quality of classification show accuracy above 94% for a non-trimmed decision tree.

A new method for three-dimensional laparoscopic ultrasound model reconstruction

DEFF Research Database (Denmark)

Fristrup, C W; Pless, T; Durup, J

2004-01-01

BACKGROUND: Laparoscopic ultrasound is an important modality in the staging of gastrointestinal tumors. Correct staging depends on good spatial understanding of the regional tumor infiltration. Three-dimensional (3D) models may facilitate the evaluation of tumor infiltration. The aim of the study...... accuracy of the new method was tested ex vivo, and the clinical feasibility was tested on a small series of patients. RESULTS: Both electromagnetic tracked reconstructions and the new 3D method gave good volumetric information with no significant difference. Clinical use of the new 3D method showed...

Assessing Clinical Significance: Does it Matter which Method we Use?

Science.gov (United States)

Atkins, David C.; Bedics, Jamie D.; Mcglinchey, Joseph B.; Beauchaine, Theodore P.

2005-01-01

Measures of clinical significance are frequently used to evaluate client change during therapy. Several alternatives to the original method devised by N. S. Jacobson, W. C. Follette, & D. Revenstorf (1984) have been proposed, each purporting to increase accuracy. However, researchers have had little systematic guidance in choosing among…

The Ability of Different Imputation Methods to Preserve the Significant Genes and Pathways in Cancer

Directory of Open Access Journals (Sweden)

Rosa Aghdam

2017-12-01

Full Text Available Deciphering important genes and pathways from incomplete gene expression data could facilitate a better understanding of cancer. Different imputation methods can be applied to estimate the missing values. In our study, we evaluated various imputation methods for their performance in preserving significant genes and pathways. In the first step, 5% genes are considered in random for two types of ignorable and non-ignorable missingness mechanisms with various missing rates. Next, 10 well-known imputation methods were applied to the complete datasets. The significance analysis of microarrays (SAM method was applied to detect the significant genes in rectal and lung cancers to showcase the utility of imputation approaches in preserving significant genes. To determine the impact of different imputation methods on the identification of important genes, the chi-squared test was used to compare the proportions of overlaps between significant genes detected from original data and those detected from the imputed datasets. Additionally, the significant genes are tested for their enrichment in important pathways, using the ConsensusPathDB. Our results showed that almost all the significant genes and pathways of the original dataset can be detected in all imputed datasets, indicating that there is no significant difference in the performance of various imputation methods tested. The source code and selected datasets are available on http://profiles.bs.ipm.ir/softwares/imputation_methods/.

The Ability of Different Imputation Methods to Preserve the Significant Genes and Pathways in Cancer.

Science.gov (United States)

Aghdam, Rosa; Baghfalaki, Taban; Khosravi, Pegah; Saberi Ansari, Elnaz

2017-12-01

Deciphering important genes and pathways from incomplete gene expression data could facilitate a better understanding of cancer. Different imputation methods can be applied to estimate the missing values. In our study, we evaluated various imputation methods for their performance in preserving significant genes and pathways. In the first step, 5% genes are considered in random for two types of ignorable and non-ignorable missingness mechanisms with various missing rates. Next, 10 well-known imputation methods were applied to the complete datasets. The significance analysis of microarrays (SAM) method was applied to detect the significant genes in rectal and lung cancers to showcase the utility of imputation approaches in preserving significant genes. To determine the impact of different imputation methods on the identification of important genes, the chi-squared test was used to compare the proportions of overlaps between significant genes detected from original data and those detected from the imputed datasets. Additionally, the significant genes are tested for their enrichment in important pathways, using the ConsensusPathDB. Our results showed that almost all the significant genes and pathways of the original dataset can be detected in all imputed datasets, indicating that there is no significant difference in the performance of various imputation methods tested. The source code and selected datasets are available on http://profiles.bs.ipm.ir/softwares/imputation_methods/. Copyright © 2017. Production and hosting by Elsevier B.V.

V-amylose structural characteristics, methods of preparation, significance, and potential applications

CSIR Research Space (South Africa)

Obiro, WC

2012-02-01

Full Text Available , and postprandial hyperglycaemia in diabetics. Various aspects of V-amylose structure, methods of preparation, factors that affect its formation, and the significance and potential applications of the V-amylose complexes are reviewed....

Determining the significance of associations between two series of discrete events : bootstrap methods /

Energy Technology Data Exchange (ETDEWEB)

Niehof, Jonathan T.; Morley, Steven K.

2012-01-01

We review and develop techniques to determine associations between series of discrete events. The bootstrap, a nonparametric statistical method, allows the determination of the significance of associations with minimal assumptions about the underlying processes. We find the key requirement for this method: one of the series must be widely spaced in time to guarantee the theoretical applicability of the bootstrap. If this condition is met, the calculated significance passes a reasonableness test. We conclude with some potential future extensions and caveats on the applicability of these methods. The techniques presented have been implemented in a Python-based software toolkit.

New significance test methods for Fourier analysis of geophysical time series

Directory of Open Access Journals (Sweden)

Z. Zhang

2011-09-01

Full Text Available When one applies the discrete Fourier transform to analyze finite-length time series, discontinuities at the data boundaries will distort its Fourier power spectrum. In this paper, based on a rigid statistics framework, we present a new significance test method which can extract the intrinsic feature of a geophysical time series very well. We show the difference in significance level compared with traditional Fourier tests by analyzing the Arctic Oscillation (AO and the Nino3.4 time series. In the AO, we find significant peaks at about 2.8, 4.3, and 5.7 yr periods and in Nino3.4 at about 12 yr period in tests against red noise. These peaks are not significant in traditional tests.

Extrapeural locating method: significance in CT-guided transthoracic pulmonary biopsy

International Nuclear Information System (INIS)

Tang Guangjian; Wang Rengui; Liu Jianxin; Sun Jingtao

2008-01-01

Objective: To evaluate the usefulness of extrapleural locating method in CT-guided transthoracic pulmonary biopsy to prevent or reduce the size of peumothorax. Methods: One hundred and fifteen cases of CT-guided transthoracic pulmonary biopsy with the pulmonary lesions not in direct contact with the pleura were selected. Of 115 cases, 46 were performed with extrapleural locating method (EPL) and 69 cases with lesion edge locating method (LEL). Taking the maximum distance between the partial and visceral pleura (MPVD) measured on the CT image after the procedure as the index of the volume of pneumothorax. The incidence and volume of pneumothorax of both groups were compared and statistically analysed with R x C Chi-Square test. The retention time of the biopsy needle in the lung parenchyma of the two group was documented and the average time was calculated in each group. Results: The incidence of pneumothorax was 45.7% (21/46), median 0.4 cm with EPL group, and 66.7% (46/69) and median 0.3cm with LEL group. When the distance between the lesion and pleura was equal or smaller than 2 cm (≤2cm), the incidence of pneumothorax was 39.4% (13/33) with EPL group and 73.2% (30/41) with LEL group, and the difference of incidence and volume of the pneumothorax between two groups was statistically significant(χ 2 =9.981, P=0.019). When the distance was larger than 2 cm (>2 cm), the incidence and volume of pneumothorax between two groups were not significant statistically. The average retention time of the biopsy needle in the lung parenchyma was (7.2 ± 1.8) s with EPL group and (58.3 ± 11.6) s with LEL group. Conclusion: The extrapleural locating method can reduce effectively the retention time of the biopsy needle in the lung parenchyma and the incidence and volume of pneumothorax in CT-guided transthoracic pulmonary biopsy. (authors)

Radiochemical studies of some preparation methods for phosphorus

International Nuclear Information System (INIS)

Loos-Neskovic, C.; Fedoroff, M.

1983-01-01

Various methods of radiochemical separation were tested for the determination of phosphorus in metals and alloys by neutron activation analysis. Classical methods of separation revealed some defects when they were applied to this problem. Methods using liquid extraction gave low yields and were not reproducible. Methods based on precipitation gave better results, but were not selective enough in most cases. Retention on alumina was not possible without preliminary separations. Authors studied a new radiochemical separation based on the extraction of elemental phosphorus in the gaseous phase after reduction at high temperature with carbon. Measurements with radioactive phosphorus showed that the extraction yield is better than 99%. (author)

A comparison of published methods of calculation of defect significance

International Nuclear Information System (INIS)

Ingham, T.; Harrison, R.P.

1982-01-01

This paper presents some of the results obtained in a round-robin calculational exercise organised by the OECD Committee on the Safety of Nuclear Installations (CSNI). The exercise was initiated to examine practical aspects of using documented elastic-plastic fracture mechanics methods to calculate defect significance. The extent to which the objectives of the exercise were met is illustrated using solutions to 'standard' problems produced by UKAEA and CEGB using the methods given in ASME XI, Appendix A, BSI PD6493, and the CEGB R/H/R6 Document. Differences in critical or tolerable defect size defined using these procedures are examined in terms of their different treatments and reasons for discrepancies are discussed. (author)

LEFT ATRIAL FUNCTION: MODERN ASSESSMENT METHODS AND CLINICAL SIGNIFICANCE

Directory of Open Access Journals (Sweden)

E. N. Pavlyukova

2017-01-01

Full Text Available Assessment of the left atrial (LA function is important aspect of comprehensive cardiovascular system estimation. Many cardiac diseases make an impact to LA work either by direct affect on myocardium or hemodynamic condition changing. It is considered, LA and left ventricle diastolic pressure is interrelated, thus without mitral valve disease LA expanding is a sign of LV filling pressure augmentation. Examination of LA size and function by analysis of atrial reservoir, conduit, and booster pump can predict cardiovascular outcomes in patients with cardiomyopathy, ischemic heart disease and valvular heart disease. The last two decades gave new technologies to accurate and comprehensive LA mechanics estimation, in the first place related to tissue Doppler imaging. Atrial strain and strain rate obtained using two-dimensional speckle-tracking echocardiography have proved to be feasible and reproducible techniques to evaluate LA mechanics.In physiological settings, LA is a highly expandable chamber with relatively low pressures. However in the presence of acute and chronic injury, LA wall stretches. LA stretching is a hallmark of structure changing with myocardial fibrosis and has influence on LA strain and strain rate. LA strain estimation could be useful in the prediction of sinus rhythm restoration and maintenance after cardioversion and catheter ablation. Low values of global longitudinal LA strain indicate irreversible LA remodeling and are related to the atrial fibrillation progression from paroxysmal to permanent forms. The most interesting in these circumstances is the potential contribution of echocardiography to thromboembolic risk stratification in atrial fibrillation and invasive procedures such as atrial ablation. Therefore, at present, the main task is to understand the ways of clinical application of data  obtained during the LA study.

Interpreting Statistical Significance Test Results: A Proposed New "What If" Method.

Science.gov (United States)

Kieffer, Kevin M.; Thompson, Bruce

As the 1994 publication manual of the American Psychological Association emphasized, "p" values are affected by sample size. As a result, it can be helpful to interpret the results of statistical significant tests in a sample size context by conducting so-called "what if" analyses. However, these methods can be inaccurate…

π π scattering by pole extrapolation methods

International Nuclear Information System (INIS)

Lott, F.W. III.

1978-01-01

A 25-inch hydrogen bubble chamber was used at the Lawrence Berkeley Laboratory Bevatron to produce 300,000 pictures of π + p interactions at an incident momentum of the π + of 2.67 GeV/c. The 2-prong events were processed using the FSD and the FOG-CLOUDY-FAIR data reduction system. Events of the nature π + p→π + pπ 0 and π + p→π + π + n with values of momentum transfer to the proton of -t less than or equal to 0.238 GeV 2 were selected. These events were used to extrapolate to the pion pole (t = m/sub π/ 2 ) in order to investigate the π π interaction with isospins of both T=1 and T=2. Two methods were used to do the extrapolation: the original Chew-Low method developed in 1959 and the Durr-Pilkuhn method developed in 1965, which takes into account centrifugal barrier penetration factors. At first it seemed that, while the Durr-Pilkuhn method gave better values for the total π π cross section, the Chew-Low method gave better values for the angular distribution. Further analysis, however, showed that, if the requirement of total OPE (one-pion-exchange) was dropped, then the Durr-Pilkuhn method gave more reasonable values of the angular distribution as well as for the total π π cross section

π π scattering by pole extrapolation methods

International Nuclear Information System (INIS)

Lott, F.W. III.

1977-01-01

A 25-inch hydrogen bubble chamber was used at the Lawrence Berkeley Laboratory Bevatron to produce 300,000 pictures of π + p interactions at an incident momentum of the π + of 2.67 GeV/c. The 2-prong events were processed using the FSD and the FOG-CLOUDY-FAIR data reduction system. Events of the nature π + p → π + pπ 0 and π + p → π + π + n with values of momentum transfer to the proton of -t less than or equal to 0.238 GeV 2 were selected. These events were used to extrapolate to the pion pole (t = m/sub π/ 2 ) in order to investigate the π π interaction with isospins of both T = 1 and T = 2. Two methods were used to do the extrapolation: the original Chew-Low method developed in 1959 and the Durr-Pilkuhn method developed in 1965 which takes into account centrifugal barrier penetration factors. At first it seemed that, while the Durr-Pilkuhn method gave better values for the total π π cross section, the Chew-Low method gave better values for the angular distribution. Further analysis, however, showed that if the requirement of total OPE (one-pion-exchange) were dropped, then the Durr-Pilkuhn method gave more reasonable values of the angular distribution as well as for the total π π cross section

Institutional delivery service utilization and associated factors among mothers who gave birth in the last 12 months in Sekela District, North West of Ethiopia: A community - based cross sectional study

Directory of Open Access Journals (Sweden)

Teferra Alemayehu

2012-07-01

Full Text Available Abstract Background Reduction of maternal mortality is a global priority particularly in developing countries including Ethiopia where maternal mortality ratio is one of the highest in the world. The key to reducing maternal mortality ratio and improving maternal health is increasing attendance by skilled health personnel throughout pregnancy and delivery. However, delivery service is significantly lower in Amhara Regional State, Ethiopia. Therefore, this study aimed to assess factors affecting institutional delivery service utilization among mothers who gave birth in the last 12 months in Sekela District, Amhara Region, Ethiopia. Methods Community-based cross-sectional study was conducted among mothers with birth in the last 12 months during August, 2010. Multistage sampling technique was used to select 371 participants. A pre tested and structured questionnaire was used to collect data. Bivariate and multivariate data analysis was performed using SPSS version 16.0 software. Results The study indicated that 12.1% of the mothers delivered in health facilities. Of 87.9% mothers who gave birth at home, 80.0% of them were assisted by family members and relatives. The common reasons for home delivery were closer attention from family members and relatives (60.9%, home delivery is usual practice (57.7%, unexpected labour (33.4%, not being sick or no problem at the time of delivery (21.6% and family influence (14.4%. Being urban resident (AOR [95% CI] = 4.6 [1.91, 10.9], ANC visit during last pregnancy (AOR [95% CI] = 4.26 [1.1, 16.4], maternal education level (AOR [95%CI] =11.98 [3.36, 41.4] and knowledge of mothers on pregnancy and delivery services (AOR [95% CI] = 2.97[1.1, 8.6] had significant associations with institutional delivery service utilization. Conclusions Very low institutional delivery service utilization was observed in the study area. Majority of the births at home were assisted by family members and relatives. ANC visit and lack of

Comparison of the xenon-133 washout method with the microsphere method in dog brain perfusion studies

International Nuclear Information System (INIS)

Heikkitae, J.; Kettunen, R.; Ahonen, A.

1982-01-01

The validity of the Xenon-washout method in estimation of regional cerebral blood flow was tested against a radioactive microsphere method in anaesthetized dogs. The two compartmental model seemed not to be well suited for cerebral perfusion studies by Xe-washout method, although bi-exponential analysis of washout curves gave perfusion values correlating with the microsphere method but depending on calculation method

Developing the RIAM method (rapid impact assessment matrix) in the context of impact significance assessment

International Nuclear Information System (INIS)

Ijaes, Asko; Kuitunen, Markku T.; Jalava, Kimmo

2010-01-01

In this paper the applicability of the RIAM method (rapid impact assessment matrix) is evaluated in the context of impact significance assessment. The methodological issues considered in the study are: 1) to test the possibilities of enlarging the scoring system used in the method, and 2) to compare the significance classifications of RIAM and unaided decision-making to estimate the consistency between these methods. The data used consisted of projects for which funding had been applied for via the European Union's Regional Development Trust in the area of Central Finland. Cases were evaluated with respect to their environmental, social and economic impacts using an assessment panel. The results showed the scoring framework used in RIAM could be modified according to the problem situation at hand, which enhances its application potential. However the changes made in criteria B did not significantly affect the final ratings of the method, which indicates the high importance of criteria A1 (importance) and A2 (magnitude) to the overall results. The significance classes obtained by the two methods diverged notably. In general the ratings given by RIAM tended to be smaller compared to intuitive judgement implying that the RIAM method may be somewhat conservative in character.

Comparison of neutron scattering, gravimetric and tensiometric methods for measuring soil water content in the field

International Nuclear Information System (INIS)

Jat, R.L.; Das, D.K.; Naskar, G.C.

1975-01-01

Water content of a sandy clay loam soil was measured by neutron scattering, gravimetric and tensiometric methods. Tensiometric measurement based on laboratory moisture retention curve gave comparatively higher moisture content than those obtained by other methods. No significant differences were observed among neutron meter, gravimetric and tensiometric measurement based on field calibration curve. Though for irrigation purposes all the methods can be used equally, use of tensiometric method with field calibration curve is suggested for easy and more accurate soil water content measurement where neutron meter is not available. (author)

Effect of extraction method and orientin content on radio-protective effect of tulsi extracts

Energy Technology Data Exchange (ETDEWEB)

Tiwari, Mrinalini; Dwarakanath, B. S.; Agrawala, Paban K., E-mail: pkagrawal@gmail.com [Institute of Nuclear Medicine and Allied Sciences, Delhi (India); Murugan, R.; Parimelazhagan, T. [Department of Botany, Bharathiar University, Coimbatore (India); Uma Devi, P. [ARA-B-3SA, Plavilakonam,Trivandrum (India); Gota, V.; Sarin, R. K. [Advanced Centre for Treatment Research and Education in Cancer, Navi Mumbai (India)

2014-07-01

Extract of tulsi leaves (Ocimum sanctum) has been reported for its radioprotective efficacy. In our initial studies we observed significant variation in the survival of irradiated mice with different batches of tulsi extracts and therefore we employed different extraction methods on leaves collected during various seasons from different localities to study any variation in the radioprotective efficacy. Orientin, a component of tulsi extract, was considered a marker. Mice whole body survival (at 10 Gy lethal whole body irradiation) study and day 11 endo-CFU-s assay (at 5 Gy WBI) were performed employing 3 treatment schedules, 50 mg/kg or 25 mg/kg b.w (single injection, 30 min irradiation), and 10 mg/kgb.w (one injection per day for 5 day, last injection being 30 min before irradiation). Single dose of 25 mg/kg b.w (both aqueous and alcoholic) did not provide any significant survival benefit. The orientin concentrations in the extracts tested varied from 3.3 to 9.91 mg/g extract as studied by HPLC method. With a single administration (i.p) of 50 mg/kg, the aqueous extract from leaves of monsoon season had an orientin content of 9.91 mg/g extract and gave a survival of 60% with a CFU-s count of 37, while extract of leaf summer leaves had an orientin content of 4.15 mg/g extract and gave a survival of 50% with a CFU-s count of 11.6. At the same dose (50 mg/kg), the aqueous extract from the winter season had an orientin content of 3.30 mg/g extract and gave 25% survival with a CFU-s count of 19, while the ethanolic extract had an orientin content of 7.70 mg/g extract and gave a survival of 50% with a CFU-s count of 13. These observations suggest that different climatic factors, orientin content and the doses of administration are important factors regulating radioprotection afforded by different extracts of tulsi. (author)

A clinical algorithm for triaging patients with significant lymphadenopathy in primary health care settings in Sudan

Directory of Open Access Journals (Sweden)

Eltahir A.G. Khalil

2013-06-01

Full Text Available Background: Tuberculosis is a major health problem in developing countries. The distinction between tuberculous lymphadenitis, non-specific lymphadenitis and malignant lymph node enlargement has to be made at primary health care levels using easy, simple and cheap methods. Objective: To develop a reliable clinical algorithm for primary care settings to triage cases ofnon-specific, tuberculous and malignant lymphadenopathies. Methods: Calculation of the odd ratios (OR of the chosen predictor variables was carried out using logistic regression. The numerical score values of the predictor variables were weighed against their respective OR. The performance of the score was evaluated by the ROC (ReceiverOperator Characteristic curve. Results: Four predictor variables; Mantoux reading, erythrocytes sedimentation rate (ESR,nocturnal fever and discharging sinuses correlated significantly with TB diagnosis and were included in the reduced model to establish score A. For score B, the reduced model included Mantoux reading, ESR, lymph-node size and lymph-node number as predictor variables for malignant lymph nodes. Score A ranged 0 to 12 and a cut-off point of 6 gave a best sensitivity and specificity of 91% and 90% respectively, whilst score B ranged -3 to 8 and a cut-off point of3 gave a best sensitivity and specificity of 83% and 76% respectively. The calculated area underthe ROC curve was 0.964 (95% CI, 0.949 – 0.980 and -0.856 (95% CI, 0.787 ‑ 0.925 for scores Aand B respectively, indicating good performance. Conclusion: The developed algorithm can efficiently triage cases with tuberculous andmalignant lymphadenopathies for treatment or referral to specialised centres for furtherwork-up.

Evaluation of four methods for separation of lymphocytes from normal individuals and patients with cancer and tuberculosis.

Science.gov (United States)

Patrick, C C; Graber, C D; Loadholt, C B

1976-01-01

An optimal technique was sought for lymphocyte recovery from normal and chronic diseased individuals. Lymphocytes were separated by four techniques: Plasmagel, Ficoll--Hypaque, a commercial semiautomatic method, and simple centrifugation using blood drawn from ten normal individuals, ten cancer patients, and ten tuberculosis patients. The lymphocyte mixture obtained after using each method was analyzed for percent recovery, amount if contamination by erythrocytes and neutrophils, and percent viability. The results show that the semiautomatic method yielded the best percent recovery of lymphocytes for normal individuals, while the simple centrifugation method contributed the highest percent recovery for cancer and tuberculosis patients. The Ficoll-Hypaque method gave the lowest erythrocyte contamination for all three types of individuals tested, while the Plasmagel method gave the lowest neutrophil contamination for all three types of individuals. The simple centrifugation method yielded all viable lymphocytes and thus gave the highest percent viability.

The Improvement of Screening the Significant Factors of Oil Blends as Bio lubricant Base Stock

International Nuclear Information System (INIS)

Noor Hajarul Ashikin Shamsuddin; Rozaini Abdullah; Zainab Hamzah; Siti Jamilah Hanim Mohd Yusof

2015-01-01

A new formulation bio lubricant base stock was developed by blending of waste cooking oil (WCO) with Jatropha curcas oil (JCO). The objective of this research is to evaluate significant factors contributing to the production of oil blends for bio lubricant application. The significant factors used in this study were oil ratio (WCO:JCO), agitation times (min) and agitation speed (rpm). The blended oil bio based lubricant was used to determine the saponification, acid, peroxide and iodine values. The experimental design used in this study was the 2 level-factorial design. In this experiment, it was found that the effect of oil ratio and interaction of oil ratio and agitation speed gave the most significant effect in oil blends as bio lubricant base stock. The highest ratio of oil blend 80 %:20 % WCO:JCO, with low agitation speed of 300 rpm and low agitation time of 30 minutes gave the optimum results. The acid, saponification, peroxide and iodine values obtained were 0.517±0.08 mg KOH/ g, 126.23±1.62 mg/ g, 7.5±2.0 m eq/ kg and 50.42±2.85 mg/ g respectively. A higher ratio of waste cooking oil blends was found to be favourable as bio lubricant base stock. (author)

Variational methods for eigenvalue problems an introduction to the weinstein method of intermediate problems

CERN Document Server

Gould, S H

1966-01-01

The first edition of this book gave a systematic exposition of the Weinstein method of calculating lower bounds of eigenvalues by means of intermediate problems. This second edition presents new developments in the framework of the material contained in the first edition, which is retained in somewhat modified form.

Relative proportions of polycyclic aromatic hydrocarbons differ between accumulation bioassays and chemical methods to predict bioavailability

Energy Technology Data Exchange (ETDEWEB)

Gomez-Eyles, Jose L., E-mail: j.l.gomezeyles@reading.ac.u [University of Reading, School of Human and Environmental Sciences, Department of Soil Science, Reading RG6 6DW, Berkshire (United Kingdom); Collins, Chris D.; Hodson, Mark E. [University of Reading, School of Human and Environmental Sciences, Department of Soil Science, Reading RG6 6DW, Berkshire (United Kingdom)

2010-01-15

Chemical methods to predict the bioavailable fraction of organic contaminants are usually validated in the literature by comparison with established bioassays. A soil spiked with polycyclic aromatic hydrocarbons (PAHs) was aged over six months and subjected to butanol, cyclodextrin and tenax extractions as well as an exhaustive extraction to determine total PAH concentrations at several time points. Earthworm (Eisenia fetida) and rye grass root (Lolium multiflorum) accumulation bioassays were conducted in parallel. Butanol extractions gave the best relationship with earthworm accumulation (r{sup 2} <= 0.54, p <= 0.01); cyclodextrin, butanol and acetone-hexane extractions all gave good predictions of accumulation in rye grass roots (r{sup 2} <= 0.86, p <= 0.01). However, the profile of the PAHs extracted by the different chemical methods was significantly different (p < 0.01) to that accumulated in the organisms. Biota accumulated a higher proportion of the heavier 4-ringed PAHs. It is concluded that bioaccumulation is a complex process that cannot be predicted by measuring the bioavailable fraction alone. - The ability of chemical methods to predict PAH accumulation in Eisenia fetida and Lolium multiflorum was hindered by the varied metabolic fate of the different PAHs within the organisms.

Development of thermal stress screening method. Application of green function method

International Nuclear Information System (INIS)

Furuhashi, Ichiro; Shibamoto, Hiroshi; Kasahara, Naoto

2004-01-01

This work was achieved for the development of the screening method of thermal transient stresses in FBR components. We proposed an approximation method for evaluations of thermal stress under variable heat transfer coefficients (non-linear problems) using the Green functions of thermal stresses with constant heat transfer coefficients (linear problems). Detailed thermal stress analyses provided Green functions for a skirt structure and a tube-sheet of Intermediate Heat Exchanger. The upper bound Green functions were obtained by the analyses using those upper bound heat transfer coefficients. The medium and the lower bound Green functions were got by the analyses of those under medium and the lower bound heat transfer coefficients. Conventional evaluations utilized the upper bound Green functions. On the other hand, we proposed a new evaluation method by using the upper bound, medium and the lower bound Green functions. The comparison of above results gave the results as follows. The conventional evaluations were conservative and appropriate for the cases under one fluid thermal transient structure such as the skirt. The conventional evaluations were generally conservative for the complicated structures under two or more fluids thermal transients such as the tube-sheet. But the danger locations could exists for the complicated structures under two or more fluids transients, namely the conventional evaluations were non-conservative. The proposed evaluations gave good estimations for these complicated structures. Though above results, we have made the basic documents of the screening method of thermal transient stresses using the conventional method and the new method. (author)

Statistical methods for estimating normal blood chemistry ranges and variance in rainbow trout (Salmo gairdneri), Shasta Strain

Science.gov (United States)

Wedemeyer, Gary A.; Nelson, Nancy C.

1975-01-01

Gaussian and nonparametric (percentile estimate and tolerance interval) statistical methods were used to estimate normal ranges for blood chemistry (bicarbonate, bilirubin, calcium, hematocrit, hemoglobin, magnesium, mean cell hemoglobin concentration, osmolality, inorganic phosphorus, and pH for juvenile rainbow (Salmo gairdneri, Shasta strain) trout held under defined environmental conditions. The percentile estimate and Gaussian methods gave similar normal ranges, whereas the tolerance interval method gave consistently wider ranges for all blood variables except hemoglobin. If the underlying frequency distribution is unknown, the percentile estimate procedure would be the method of choice.

Coral bleaching, hurricane damage, and benthic cover on coral reefs in St. John, U.S. Virgin Islands: A comparison of surveys with the chain transect method and videography

Science.gov (United States)

Rogers, C.S.; Miller, J.

2001-01-01

The linear chain transect method and videography were used to quantify the percent cover by corals, macroalgae, gorgonians, other living organisms, and substrate along permanent transects on two fringing reefs off St. John. Both methods were used simultaneously on Lameshur reef in November 1998, and on Newfound reef in March and October 1998. Hurricane Georges passed over St. John in September 1998, and a severe coral bleaching episode began the same month. Both methods gave remarkably similar values for coral cover, while the video method gave consistently higher values for gorgonians and macroalgae. The most dramatic difference was in the quantification of bleaching. At Newfound, the chain method indicated 13.4% (SD = 14.1) of the coral tissues were bleached and the video method, 43.4% (SD = 13.0). Corresponding values at Lameshur were 18.1% (SD = 22.3) and 46.5% (SD = 13.3). Although hurricane damage was conspicuous at Newfound reef, neither method showed significant changes in coral cover or other categories as a result of the storm.

Significance of roentgenologic and nuclear medicine methods in diagnosis and operative indications of coronary artery disease

Energy Technology Data Exchange (ETDEWEB)

Felix, R [Bonn Univ. (F.R. Germany). Radiologische Klinik; Winkler, C [Bonn Univ. (F.R. Germany). Inst. fuer Klinische und Experimentelle Nuklearmedizin; Schaede, A [Bonn Univ. (F.R. Germany). Medizinische Klinik

1976-03-01

Significance and technique of roentgenologic and nuclear medicine methods for evaluation of coronary artery disease and myocardial perfusion are presented. Some routinely used methods in nuclear medicine are briefly discussed concerning the evaluation of left ventricular function.

Comparison of RNA Extraction Methods for the Identification of Grapevine fan leaf virus

Directory of Open Access Journals (Sweden)

Z. Gholampour

2016-06-01

polysaccharide. RNA preparations were further tested for quality using RT-PCR reactions. In PCR analyses, whereas traditional methods yielded amplification ratios of 40-88% and the commercial isolation kits yielded amplification ratios of 16%. The RNA from Silica, high salt phenol-chloroform extraction, TRIzol and CTAB-PVPP extraction methods consistently resulted in amplification in 40, 56, 60 and 88% of the samples, respectively. Discussion: The choice of extraction method depends upon the application in which the RNA will be used. Yield, A260/280, and A260/230 ratios are not good indicators of RT-PCR competent RNA. RNA should be checked for degradation. For RT-PCR, four extraction protocols of Silica, high salt phenol-chloroform extraction, TRIzol and CTAB-PVPP gave consistent product, and however, the last one was the most efficient method. The Silica extraction had significant RNA degradation, making problems in quantification with RT-PCR. Sodium perchlorate extractions had slight RNA degradation, low extraction efficiency, and cost substantially more than the Tris-LiCl method. The CTAB-PVPP method provided high yield and appropriate quality, consistent results for identification of the virus in RT-PCR. The high salt phenol-chloroform and TRIzol extraction were significantly cheaper than CTAB-PVPP methodical, but gave lower yields and were unsuitable for obtaining questionable results in RT-PCR.

Method of extracting significant trouble information of nuclear power plants using probabilistic analysis technique

International Nuclear Information System (INIS)

Shimada, Yoshio; Miyazaki, Takamasa

2005-01-01

In order to analyze and evaluate large amounts of trouble information of overseas nuclear power plants, it is necessary to select information that is significant in terms of both safety and reliability. In this research, a method of efficiently and simply classifying degrees of importance of components in terms of safety and reliability while paying attention to root-cause components appearing in the information was developed. Regarding safety, the reactor core damage frequency (CDF), which is used in the probabilistic analysis of a reactor, was used. Regarding reliability, the automatic plant trip probability (APTP), which is used in the probabilistic analysis of automatic reactor trips, was used. These two aspects were reflected in the development of criteria for classifying degrees of importance of components. By applying these criteria, a simple method of extracting significant trouble information of overseas nuclear power plants was developed. (author)

A method for risk-informed safety significance categorization using the analytic hierarchy process and bayesian belief networks

International Nuclear Information System (INIS)

Ha, Jun Su; Seong, Poong Hyun

2004-01-01

A risk-informed safety significance categorization (RISSC) is to categorize structures, systems, or components (SSCs) of a nuclear power plant (NPP) into two or more groups, according to their safety significance using both probabilistic and deterministic insights. In the conventional methods for the RISSC, the SSCs are quantitatively categorized according to their importance measures for the initial categorization. The final decisions (categorizations) of SSCs, however, are qualitatively made by an expert panel through discussions and adjustments of opinions by using the probabilistic insights compiled in the initial categorization process and combining the probabilistic insights with the deterministic insights. Therefore, owing to the qualitative and linear decision-making process, the conventional methods have the demerits as follows: (1) they are very costly in terms of time and labor, (2) it is not easy to reach the final decision, when the opinions of the experts are in conflict and (3) they have an overlapping process due to the linear paradigm (the categorization is performed twice - first, by the engineers who propose the method, and second, by the expert panel). In this work, a method for RISSC using the analytic hierarchy process (AHP) and bayesian belief networks (BBN) is proposed to overcome the demerits of the conventional methods and to effectively arrive at a final decision (or categorization). By using the AHP and BBN, the expert panel takes part in the early stage of the categorization (that is, the quantification process) and the safety significance based on both probabilistic and deterministic insights is quantified. According to that safety significance, SSCs are quantitatively categorized into three categories such as high safety significant category (Hi), potentially safety significant category (Po), or low safety significant category (Lo). The proposed method was applied to the components such as CC-V073, CV-V530, and SI-V644 in Ulchin Unit

A gamma-source method of measuring soil moisture

International Nuclear Information System (INIS)

Al-Jeboori, M.A.; Ameen, I.A.

1986-01-01

Water content in soil column was measured using NaI scintillation detector 5 mci Cs-137 as a gamma source. The measurements were done with a back scatter gauge, restricted with scattering angle less to than /2 overcome the effect of soil type. A 3 cm air gap was maintained between the front of the detector and the wall of the soil container in order to increase the counting rate. The distance between the center of the source and the center of the back scattering detector was 14 cm. The accuracy of the measurements was 0.63. For comparision, a direct rays method was used to measure the soil moisture. The results gave an error of 0.65. Results of the two methods were compared with the gravimetric method which gave an error of 0.18 g/g and 0.17 g/g for direct and back method respectively. The quick direct method was used to determine the gravimetric and volumetric percentage constants, and were found to be 1.62 and 0.865 respectively. The method then used to measure the water content in the layers of soil column.(6 tabs., 4 figs., 12 refs.)

Optimization of Ex Vivo Murine Bone Marrow Derived Immature Dendritic Cells: A Comparative Analysis of Flask Culture Method and Mouse CD11c Positive Selection Kit Method

Directory of Open Access Journals (Sweden)

Rahul Ashok Gosavi

2018-01-01

Full Text Available 12–14 days of culturing of bone marrow (BM cells containing various growth factors is widely used method for generating dendritic cells (DCs from suspended cell population. Here we compared flask culture method and commercially available CD11c Positive Selection kit method. Immature BMDCs’ purity of adherent as well as suspended cell population was generated in the decreasing concentration of recombinant-murine granulocyte-macrophage colony-stimulating factor (rmGM-CSF in nontreated tissue culture flasks. The expression of CD11c, MHCII, CD40, and CD86 was measured by flow cytometry. We found significant difference (P<0.05 between the two methods in the adherent cells population but no significant difference was observed between the suspended cell populations with respect to CD11c+ count. However, CD11c+ was significantly higher in both adhered and suspended cell population by culture method but kit method gave more CD11c+ from suspended cells population only. On the other hand, using both methods, immature DC expressed moderate level of MHC class II molecules as well as low levels of CD40 and CD86. Our findings suggest that widely used culture method gives the best results in terms of yield, viability, and purity of BMDCs from both adherent and suspended cell population whereas kit method works well for suspended cell population.

Comparative study of discretization methods of microarray data for inferring transcriptional regulatory networks

Directory of Open Access Journals (Sweden)

Ji Wei

2010-10-01

Full Text Available Abstract Background Microarray data discretization is a basic preprocess for many algorithms of gene regulatory network inference. Some common discretization methods in informatics are used to discretize microarray data. Selection of the discretization method is often arbitrary and no systematic comparison of different discretization has been conducted, in the context of gene regulatory network inference from time series gene expression data. Results In this study, we propose a new discretization method "bikmeans", and compare its performance with four other widely-used discretization methods using different datasets, modeling algorithms and number of intervals. Sensitivities, specificities and total accuracies were calculated and statistical analysis was carried out. Bikmeans method always gave high total accuracies. Conclusions Our results indicate that proper discretization methods can consistently improve gene regulatory network inference independent of network modeling algorithms and datasets. Our new method, bikmeans, resulted in significant better total accuracies than other methods.

Thresholds for statistical and clinical significance in systematic reviews with meta-analytic methods

DEFF Research Database (Denmark)

Jakobsen, Janus Christian; Wetterslev, Jorn; Winkel, Per

2014-01-01

BACKGROUND: Thresholds for statistical significance when assessing meta-analysis results are being insufficiently demonstrated by traditional 95% confidence intervals and P-values. Assessment of intervention effects in systematic reviews with meta-analysis deserves greater rigour. METHODS......: Methodologies for assessing statistical and clinical significance of intervention effects in systematic reviews were considered. Balancing simplicity and comprehensiveness, an operational procedure was developed, based mainly on The Cochrane Collaboration methodology and the Grading of Recommendations...... Assessment, Development, and Evaluation (GRADE) guidelines. RESULTS: We propose an eight-step procedure for better validation of meta-analytic results in systematic reviews (1) Obtain the 95% confidence intervals and the P-values from both fixed-effect and random-effects meta-analyses and report the most...

Comparative study for methods to determine the seismic response of NPP structures

International Nuclear Information System (INIS)

Varpasuo, P.

1995-01-01

There are many different important problem areas in evaluating the seismic response of structures. In this study the effort is concentrated on three of these areas. The first task is the mathematical formulation of earthquake excitation. The random vibration theory is taken as the tool in this task. The second area of interest in this study is the soil-structure interaction analysis. The approach of impedance functions is chosen and the focal point of interest is the significance of frequency dependent impedance functions. The third area of interest is the methods to determine the structural response. The following three methods were tested: the mode superposition time history method; the complex frequency response method; the response spectrum method. The comparison was made with the aid of MSC/NASTRAN code. The three methods gave for outer containment building response results which were in good agreement with each other. (author). 4 refs., 5 figs

Institutional delivery service utilization and associated factors among mothers who gave birth in the last 12 months in Sekela District, north west of Ethiopia: a community-based cross sectional study.

Science.gov (United States)

Teferra, Alemayehu Shimeka; Alemu, Fekadu Mazengia; Woldeyohannes, Solomon Meseret

2012-07-31

Reduction of maternal mortality is a global priority particularly in developing countries including Ethiopia where maternal mortality ratio is one of the highest in the world. The key to reducing maternal mortality ratio and improving maternal health is increasing attendance by skilled health personnel throughout pregnancy and delivery. However, delivery service is significantly lower in Amhara Regional State, Ethiopia. Therefore, this study aimed to assess factors affecting institutional delivery service utilization among mothers who gave birth in the last 12 months in Sekela District, Amhara Region, Ethiopia. Community-based cross-sectional study was conducted among mothers with birth in the last 12 months during August, 2010. Multistage sampling technique was used to select 371 participants. A pre tested and structured questionnaire was used to collect data. Bivariate and multivariate data analysis was performed using SPSS version 16.0 software. The study indicated that 12.1% of the mothers delivered in health facilities. Of 87.9% mothers who gave birth at home, 80.0% of them were assisted by family members and relatives. The common reasons for home delivery were closer attention from family members and relatives (60.9%), home delivery is usual practice (57.7%), unexpected labour (33.4%), not being sick or no problem at the time of delivery (21.6%) and family influence (14.4%). Being urban resident (AOR [95% CI] = 4.6 [1.91, 10.9]), ANC visit during last pregnancy (AOR [95% CI] = 4.26 [1.1, 16.4]), maternal education level (AOR [95%CI] =11.98 [3.36, 41.4]) and knowledge of mothers on pregnancy and delivery services (AOR [95% CI] = 2.97[1.1, 8.6]) had significant associations with institutional delivery service utilization. Very low institutional delivery service utilization was observed in the study area. Majority of the births at home were assisted by family members and relatives. ANC visit and lack of knowledge on pregnancy and delivery services were found to

Method of administration of PROMIS scales did not significantly impact score level, reliability, or validity

DEFF Research Database (Denmark)

Bjorner, Jakob B; Rose, Matthias; Gandek, Barbara

2014-01-01

OBJECTIVES: To test the impact of the method of administration (MOA) on score level, reliability, and validity of scales developed in the Patient Reported Outcomes Measurement Information System (PROMIS). STUDY DESIGN AND SETTING: Two nonoverlapping parallel forms each containing eight items from......, no significant mode differences were found and all confidence intervals were within the prespecified minimal important difference of 0.2 standard deviation. Parallel-forms reliabilities were very high (ICC = 0.85-0.93). Only one across-mode ICC was significantly lower than the same-mode ICC. Tests of validity...... questionnaire (PQ), personal digital assistant (PDA), or personal computer (PC) and a second form by PC, in the same administration. Method equivalence was evaluated through analyses of difference scores, intraclass correlations (ICCs), and convergent/discriminant validity. RESULTS: In difference score analyses...

Azoreductase and Nitroreductase in Human Feces: Comparison of Methods to Measure Specific Activities in the Absence of Oxygen

OpenAIRE

Carman, Robert J.; Woodburn, Mary Alice

2011-01-01

We measured the specific activity of azoreductase and nitroreductase in eight fresh samples of human feces, using three ways to produce anaerobic assay conditions. A fourth, bench top aerobic assay was also run. Using Oxyrase to produce anaerobic conditions on the open bench gave a significantly higher level of azoreductase than did running the assay entirely in an anaerobic the glove box. Nitroreductase levels were similar in the two assays. Oxyrase and the glove box both gave significantly ...

The Numerical Welding Simulation - Developments and Validation of Simplified and Bead Lumping Methods

International Nuclear Information System (INIS)

Baup, Olivier

2001-01-01

The aim of this work was to study the TIG multipass welding process on stainless steel, by means of numerical methods and then to work out simplified and bead lumping methods in order to reduce adjusting and realisation times of these calculations. A simulation was used as reference for the validation of these methods; after the presentation of the test series having led to the option choices of this calculation (2D generalised plane strains, elastoplastic model with an isotropic hardening, hardening restoration due to high temperatures), various simplifications were tried on a plate geometry. These simplifications related various modelling points with a correct plastic flow representation in the plate. The use of a reduced number of thermal fields characterising the bead deposit and a low number of tensile curves allow to obtain interesting results, decreasing significantly the Computing times. In addition various lumping bead methods have been studied and concerning both the shape and the thermic of the macro-deposits. The macro-deposit shapes studied are in 'L', or in layer or they represent two beads one on top of the other. Among these three methods, only those using a few number of lumping beads gave bad results since thermo-mechanical history was deeply modified near and inside the weld. Thereafter, simplified methods have been applied to a tubular geometry. On this new geometry, experimental measurements were made during welding, which allow a validation of the reference calculation. Simplified and reference calculations gave approximately the same stress fields as found on plate geometry. Finally, in the last part of this document a procedure for automatic data setting permitting to reduce significantly the calculation phase preparation is presented. It has been applied to the calculation of thick pipe welding in 90 beads; the results are compared with a simplified simulation realised by Framatome and with experimental measurements. A bead by

Defining and determining the significance of impacts: concepts and methods

International Nuclear Information System (INIS)

Christensen, S.W.; Van Winkle, W.; Mattice, J.S.

1975-01-01

The term impact is conceptually and mathematically defined to be the difference in the state or value of an ecosystem with versus without the source of impact. Some resulting problems associated with the measurement of impacts based on comparisons of baseline and operational data are discussed briefly. The concept of a significant adverse impact on a biological system is operationally defined in terms of an adverse impact which, according to a proposed decision-tree, justifies rejection of a project or a change in its site, design, or mode of operation. A gradient of increasing difficulty in the prediction of impacts exists as the scope of the assessment is expanded to consider long-term, far-field impacts with respect to higher levels of biological organization (e.g., communities or ecosystems). The analytical methods available for predicting short-term, near-field impacts are discussed. Finally, the role of simulation modeling as an aid to professional judgment in predicting the long-term, far-field consequences of impacts is considered, and illustrated with an example. (U.S.)

The effect of kinds and concentration of cryoprotectant and thawing methods on frozen semen of Arab chicken

Directory of Open Access Journals (Sweden)

Sofjan Iskandar

2006-03-01

Full Text Available The success of freezing chicken semen is the hope for preserving Indonesian native chickens. Semen from twenty Arab roosters were collected using massage technique once in a week. Cryoprotectant DMA (dimethyl acetamide or DMF (dimethyl formalmide of 7 or 9% and thawing A at temperature of 30oC for 30 seconds or in B at 5oC for 5 minutes. The volume of fresh semen was 0.3 ± 0.072 ml/ejaculate, white colour, rather thick to thick, with 2200 ± 372 millions sperms/ml and pH 6.95 ± 0.32, 4+/3+ mass movement, 80% motility, 84 ± 4.48% and abnormality of 14.75 ± 1.28%. There were not statistically significant (P>0.05 effect of interaction of treatments (kinds and concentrations of cryoprotectant, and thawing methods on motility and live-sperms. Sperm motility preserved with DMA (34.69% significantly higher than with DMF (29.84%. Sperm motility was also significantly higher (34.53% when preserved with 7% cryoprotectant than with 9% (30%. Thawing-A significantly gave higher motility (35.31% than thawing-B did (29.22%. Live-sperms of semen preserved with DMA (46.75% was significantly higher than with DMF (41.72%. Cryoprotectant concentration of 7% gave higher live-sperms (46.98% than of 9% did (41.48%. Thawing-A left live-sperms of 47.14%, which was significantly higher than thawing-B did (41.30%.

Antinuclear antibodies: clinical significance of fluorescence patterns

International Nuclear Information System (INIS)

Cordeiro, S.L.; Habermann, F.; Franco, M.F.

1981-01-01

Fifty-four patients with 212 sera positive for antinuclear antibodies (ANA) were studied to: 1) determine the immunofluorescent nuclear staining patterns using Burnham's technique and simplified classification; 2) note the specificity of fluorescence patterns among the various connective tissue diseases; 3) study comparatively the fluorescence paterns employing 5 different antigen substrates; 4) correlate ANA titers and fluorescence patterns with renal involvement in systemic lupus erythematosus (SLE). It was observed: 1) most of the sera gave nonparticulate fluorescent patterns: peripheral, homogeneous, or peripheral-homogeneneous; 2) 55,5% of the patients had LE and most of those sera showed nonparticulate fluorescent patterns; 3) the sera displayed no specificity for any of the following antigen substrates: imprints of human normal spleen, frozen rat liver and kidney sections, frozen mouse kidney sections and perypheral human blood smears; 4) imprints of normal human spleen were the best substrate for accurate identification of fluorescent patterns; 5) sera from SLE patients with renal involvement showed higher ANA titers in relation to patients without renal involvement; both groups of sera gave similar ANA fluorescent patterns. (Author) [pt

A fast method for the unit scheduling problem with significant renewable power generation

International Nuclear Information System (INIS)

Osório, G.J.; Lujano-Rojas, J.M.; Matias, J.C.O.; Catalão, J.P.S.

2015-01-01

Highlights: • A model to the scheduling of power systems with significant renewable power generation is provided. • A new methodology that takes information from the analysis of each scenario separately is proposed. • Based on a probabilistic analysis, unit scheduling and corresponding economic dispatch are estimated. • A comparison with others methodologies is in favour of the proposed approach. - Abstract: Optimal operation of power systems with high integration of renewable power sources has become difficult as a consequence of the random nature of some sources like wind energy and photovoltaic energy. Nowadays, this problem is solved using Monte Carlo Simulation (MCS) approach, which allows considering important statistical characteristics of wind and solar power production such as the correlation between consecutive observations, the diurnal profile of the forecasted power production, and the forecasting error. However, MCS method requires the analysis of a representative amount of trials, which is an intensive calculation task that increases considerably with the number of scenarios considered. In this paper, a model to the scheduling of power systems with significant renewable power generation based on scenario generation/reduction method, which establishes a proportional relationship between the number of scenarios and the computational time required to analyse them, is proposed. The methodology takes information from the analysis of each scenario separately to determine the probabilistic behaviour of each generator at each hour in the scheduling problem. Then, considering a determined significance level, the units to be committed are selected and the load dispatch is determined. The proposed technique was illustrated through a case study and the comparison with stochastic programming approach was carried out, concluding that the proposed methodology can provide an acceptable solution in a reduced computational time

Using the Bootstrap Method for a Statistical Significance Test of Differences between Summary Histograms

Science.gov (United States)

Xu, Kuan-Man

2006-01-01

A new method is proposed to compare statistical differences between summary histograms, which are the histograms summed over a large ensemble of individual histograms. It consists of choosing a distance statistic for measuring the difference between summary histograms and using a bootstrap procedure to calculate the statistical significance level. Bootstrapping is an approach to statistical inference that makes few assumptions about the underlying probability distribution that describes the data. Three distance statistics are compared in this study. They are the Euclidean distance, the Jeffries-Matusita distance and the Kuiper distance. The data used in testing the bootstrap method are satellite measurements of cloud systems called cloud objects. Each cloud object is defined as a contiguous region/patch composed of individual footprints or fields of view. A histogram of measured values over footprints is generated for each parameter of each cloud object and then summary histograms are accumulated over all individual histograms in a given cloud-object size category. The results of statistical hypothesis tests using all three distances as test statistics are generally similar, indicating the validity of the proposed method. The Euclidean distance is determined to be most suitable after comparing the statistical tests of several parameters with distinct probability distributions among three cloud-object size categories. Impacts on the statistical significance levels resulting from differences in the total lengths of satellite footprint data between two size categories are also discussed.

Radioimmunoassay for chicken avidin. Comparison with a (/sup 14/C)biotin-binding method

Energy Technology Data Exchange (ETDEWEB)

Kulomaa, M S; Elo, H A; Tuohimaa, P J [Tampere Univ. of Tech. (Finland)

1978-11-01

A double-antibody solid-phase radioimmunoassay for chicken avidin is reported. Avidin was labelled with /sup 125/I by the chloramine-T method. The bound and free avidin were separated with a second antibody bound to a solid matrix. In the logit-log scale the standard curve was linear from 1-2 to 100-200ng of avidin/ml. Cross-reaction of ovalbumin was less than 0.015%. Saturation of biotin-binding sites of avidin with an excess of biotin decreased radioimmunoassay values by about 15%. Recovery studies indicated that avidin can be assayed from all chicken tissues studied with radioimmunoassay, whereas the (/sup 14/C)biotin/bentonite method gave poor recoveries for avidin in the liver and kidney. Radioimmunoassay and the (/sup 14/C)biotin/bentonite method gave similar concentrations for oviduct avidin.

A method for the estimation of the significance of cross-correlations in unevenly sampled red-noise time series

Science.gov (United States)

Max-Moerbeck, W.; Richards, J. L.; Hovatta, T.; Pavlidou, V.; Pearson, T. J.; Readhead, A. C. S.

2014-11-01

We present a practical implementation of a Monte Carlo method to estimate the significance of cross-correlations in unevenly sampled time series of data, whose statistical properties are modelled with a simple power-law power spectral density. This implementation builds on published methods; we introduce a number of improvements in the normalization of the cross-correlation function estimate and a bootstrap method for estimating the significance of the cross-correlations. A closely related matter is the estimation of a model for the light curves, which is critical for the significance estimates. We present a graphical and quantitative demonstration that uses simulations to show how common it is to get high cross-correlations for unrelated light curves with steep power spectral densities. This demonstration highlights the dangers of interpreting them as signs of a physical connection. We show that by using interpolation and the Hanning sampling window function we are able to reduce the effects of red-noise leakage and to recover steep simple power-law power spectral densities. We also introduce the use of a Neyman construction for the estimation of the errors in the power-law index of the power spectral density. This method provides a consistent way to estimate the significance of cross-correlations in unevenly sampled time series of data.

Soil hydrophobicity: comparative study of usual determination methods

Directory of Open Access Journals (Sweden)

Eduardo Saldanha Vogelmann

2015-02-01

Full Text Available Hydrophobic or water repellent soils slowly absorb water because of the low wett ability of the soil particles which are coated with hydrophobic organic substances. These pose significant effects on plant growth, water infiltration and retention, surface runoff and erosion. The objective of this study was to compare the performance of tension micro-infiltrometer(TMI and the water drop penetration time (WDPT methods in the determination of the hydrophobicity index of eighteen soils from southern Brazil. Soil samples were collected from the 0-5cm soil layer to determine particle size distribution, organic matter content, hydrophobicity index of soil aggregates and droplet penetration time of disaggregated and sieved soil samples. For the TMI method the soil samples were subjected to minor changes due to the use of macroaggregates to preserve the distribution of solid constituents in the soil. Due to the homogeneity of the soil samples the WDPT method gave smaller coefficients of variation unlike the TMI method where the soil structure is preserved. However, both methods had low coefficients of variation, and are thus effective for determining the soil hydrophobicity, especially when the log hydrophobicity index or log WDPT is >1.

Evaluation of sampling methods for Bacillus spore-contaminated HVAC filters.

Science.gov (United States)

Calfee, M Worth; Rose, Laura J; Tufts, Jenia; Morse, Stephen; Clayton, Matt; Touati, Abderrahmane; Griffin-Gatchalian, Nicole; Slone, Christina; McSweeney, Neal

2014-01-01

The objective of this study was to compare an extraction-based sampling method to two vacuum-based sampling methods (vacuum sock and 37mm cassette filter) with regards to their ability to recover Bacillus atrophaeus spores (surrogate for Bacillus anthracis) from pleated heating, ventilation, and air conditioning (HVAC) filters that are typically found in commercial and residential buildings. Electrostatic and mechanical HVAC filters were tested, both without and after loading with dust to 50% of their total holding capacity. The results were analyzed by one-way ANOVA across material types, presence or absence of dust, and sampling device. The extraction method gave higher relative recoveries than the two vacuum methods evaluated (p≤0.001). On average, recoveries obtained by the vacuum methods were about 30% of those achieved by the extraction method. Relative recoveries between the two vacuum methods were not significantly different (p>0.05). Although extraction methods yielded higher recoveries than vacuum methods, either HVAC filter sampling approach may provide a rapid and inexpensive mechanism for understanding the extent of contamination following a wide-area biological release incident. Published by Elsevier B.V.

Testing statistical significance scores of sequence comparison methods with structure similarity

Directory of Open Access Journals (Sweden)

Leunissen Jack AM

2006-10-01

Full Text Available Abstract Background In the past years the Smith-Waterman sequence comparison algorithm has gained popularity due to improved implementations and rapidly increasing computing power. However, the quality and sensitivity of a database search is not only determined by the algorithm but also by the statistical significance testing for an alignment. The e-value is the most commonly used statistical validation method for sequence database searching. The CluSTr database and the Protein World database have been created using an alternative statistical significance test: a Z-score based on Monte-Carlo statistics. Several papers have described the superiority of the Z-score as compared to the e-value, using simulated data. We were interested if this could be validated when applied to existing, evolutionary related protein sequences. Results All experiments are performed on the ASTRAL SCOP database. The Smith-Waterman sequence comparison algorithm with both e-value and Z-score statistics is evaluated, using ROC, CVE and AP measures. The BLAST and FASTA algorithms are used as reference. We find that two out of three Smith-Waterman implementations with e-value are better at predicting structural similarities between proteins than the Smith-Waterman implementation with Z-score. SSEARCH especially has very high scores. Conclusion The compute intensive Z-score does not have a clear advantage over the e-value. The Smith-Waterman implementations give generally better results than their heuristic counterparts. We recommend using the SSEARCH algorithm combined with e-values for pairwise sequence comparisons.

An adaptive-binning method for generating constant-uncertainty/constant-significance light curves with Fermi-LAT data

International Nuclear Information System (INIS)

Lott, B.; Escande, L.; Larsson, S.; Ballet, J.

2012-01-01

Here, we present a method enabling the creation of constant-uncertainty/constant-significance light curves with the data of the Fermi-Large Area Telescope (LAT). The adaptive-binning method enables more information to be encapsulated within the light curve than with the fixed-binning method. Although primarily developed for blazar studies, it can be applied to any sources. Furthermore, this method allows the starting and ending times of each interval to be calculated in a simple and quick way during a first step. The reported mean flux and spectral index (assuming the spectrum is a power-law distribution) in the interval are calculated via the standard LAT analysis during a second step. In the absence of major caveats associated with this method Monte-Carlo simulations have been established. We present the performance of this method in determining duty cycles as well as power-density spectra relative to the traditional fixed-binning method.

Evaluation of spray and point inoculation methods for the phenotyping of Puccinia striiformis on wheat

DEFF Research Database (Denmark)

Sørensen, Chris Khadgi; Thach, Tine; Hovmøller, Mogens Støvring

2016-01-01

flexible application procedure for spray inoculation and it gave highly reproducible results for virulence phenotyping. Six point inoculation methods were compared to find the most suitable for assessment of pathogen aggressiveness. The use of Novec 7100 and dry dilution with Lycopodium spores gave...... for the assessment of quantitative epidemiological parameters. New protocols for spray and point inoculation of P. striiformis on wheat are presented, along with the prospect for applying these in rust research and resistance breeding activities....

Comparison of breeding methods for forage yield in red clover

Directory of Open Access Journals (Sweden)

Libor Jalůvka

2009-01-01

Full Text Available Three methods of red clover (Trifolium pratense L. breeding for forage yield in two harvest years on locations in Bredelokke (Denmark, Hladké Životice (Czech Republic and Les Alleuds (France were compared. Three types of 46 candivars1, developed by A recurrent selection in subsequent generations (37 candivars, divided into early and late group, B polycross progenies (4 candivars and C ge­no-phe­no­ty­pic selection (5 candivars were compared. The trials were sown in 2005 and cut three times in 2006 and 2007; their evaluation is based primarily on total yield of dry matter. The candivars developed by polycross and geno-phenotypic selections gave significantly higher yields than candivars from the recurrent selection. However, the candivars developed by the methods B and C did not differ significantly. The candivars developed by these progressive methods were suitable for higher yielding and drier environment in Hladké Životice (where was the highest yield level even if averaged annual precipitation were lower by 73 and 113 mm in comparison to other locations, respectively; here was ave­ra­ge yield higher by 19 and 13% for B and C in comparison to A method. Highly significant interaction of the candivars with locations was found. It can be concluded that varieties specifically aimed to different locations by the methods B and C should be bred; also the parental entries should be selected there.

A simplified method for processing dynamic images of gastric antrum

DEFF Research Database (Denmark)

Madsen, J L; Graff, J; Fugisang, S

2000-01-01

versus geometric centre curve. In all subjects, our technique gave unequivocal frequencies of antral contractions at each time point. Statistical analysis did not reveal any intraindividual variation in this frequency during gastric emptying. We believe that the simplified scintigraphic method...

Microalbuminuria: It's Significance, risk factors and methods of ...

African Journals Online (AJOL)

Alasia Datonye

Male gender Hypertension. High salt (and protein ) ... gender and high salt intake are also to be associated with a .... method has advantages and disadvantages, and the choice depends .... single voided urine samples to estimate quantitative proteinuria. .... in an Urban and Periurban School, Port Harcourt , Rivers. State.

En gave til skolernes litteraturundervisning

DEFF Research Database (Denmark)

Larsen, Peter Stein

2015-01-01

Mens Caspar Erics debutdigtsamling, " 7/ 11", fra sidste år var præget af en stil, hvor der i en hæsblæsende strøm blev refereret til Facebook, You-Tube, iPhone, mp3, Macbook, Twitter og Netflix, frem for at man fik noget at vide om, hvad der rørte sig i ... ......Mens Caspar Erics debutdigtsamling, " 7/ 11", fra sidste år var præget af en stil, hvor der i en hæsblæsende strøm blev refereret til Facebook, You-Tube, iPhone, mp3, Macbook, Twitter og Netflix, frem for at man fik noget at vide om, hvad der rørte sig i ... ...

Geomagnetism gave me my bearings

Indian Academy of Sciences (India)

Lawrence

days at the University of Delhi, but also had the opportunity to attend summer ... versity in the United States, I worked on a problem in condensed- matter physics. ... diately after my Ph.D. made me open to the idea of taking up research in an ...

Optimal method for collection of umbilical cord blood: an Egyptian trial for a public cord blood bank.

Science.gov (United States)

Bassiouny, M R; El-Chennawi, F; Mansour, A K; Yahia, S; Darwish, A

2015-06-01

Umbilical cord blood (UCB) contains stem cells and can be used as an alternative to bone marrow transplantation. Engraftment is dependent on the total nucleated cell (TNC) and CD34+ cell counts of the cord blood units. This study was designed to evaluate the effect of the method of collection of the UCB on the yield of the cord blood units. Informed consent was obtained from 100 eligible mothers for donation of cord blood. Both in utero and ex utero methods were used for collection. The cord blood volume was measured. The TNC and the CD34+ cell counts were enumerated. We have found that in utero collection gave significantly larger volumes of cord blood and higher TNC counts than ex utero collection. There was no significant difference between both methods regarding the CD34+ cell counts. This study revealed a significant correlation between the volume of the collected cord blood and both TNC and CD34+ cell counts. It is better to collect cord blood in utero before placental delivery to optimize the quality of the cord blood unit. © 2015 AABB.

VCO Production from Fresh Old Coconut Bunch by Circulating and Pumping Method

Directory of Open Access Journals (Sweden)

Muhamad Maulana Azimatun Nur

2012-04-01

Full Text Available VCO (Virgin Coconut Oil is one of coco-diesel source, made without high heating and chemicals. Commercial processes production, such fermentation and centrifugation usually need more time and expensive in cost and investment. Circulating by pumping through a nozzle is a new process method invented to produce VCO. The process followed by coalescence method, breaking emulsion by hitting particles through pipe and nozzle. The problem of this method was that the product gave lower yield than another method and not yet qualified. This research was purposed to discover correlation between pressure and time of circulation variables against yield and content (FFA, Peroxide, water content represented by SNI (national Indonesian standard. Producing VCO initiated by producing coconut milk from fresh old coconut, then each 1 litre milk were pumped through the pipe and nozzle with variation of circulations pressures and time. The results were decanted for 10 hours so the oil and water would be separated. The oil at upper layer was taken as final product. Then the last step was analysed the oils and oil cake (blondo. The results showed that pressure and time of circulating variables gave impact to the yield. On optimum variables, 2 atm pressure and 15 minutes of circulating gave better results with 97% yield. This operating variables also affecting oil quality. The minimum water content is 0.1%, free fatty acid is 0.18% and peroxide value is 2 mg/kg eq. The results showed that all of parameters meet the SNI standard.

VCO Production from Fresh Old Coconut Bunch by Circulating and Pumping Method

Directory of Open Access Journals (Sweden)

Muhamad Maulana Azimatun Nur

2012-02-01

Full Text Available VCO (Virgin Coconut Oil is one of coco-diesel source, made without high heating and chemicals. Commercial processes production, such fermentation and centrifugation usually need more time and expensive in cost and investment. Circulating by pumping through a nozzle is a new process method invented to produce VCO. The process followed by coalescence method, breaking emulsion by hitting particles through pipe and nozzle. The problem of this method was that the product gave lower yield than another method and not yet qualified. This research was purposed to discover correlation between pressure and time of circulation variables against yield and content (FFA, Peroxide, water content represented by SNI (national Indonesian standard. Producing VCO initiated by producing coconut milk from fresh old coconut, then each 1 litre milk were pumped through the pipe and nozzle with variation of circulations pressures and time. The results were decanted for 10 hours so the oil and water would be separated. The oil at upper layer was taken as final product. Then the last step was analysed the oils and oil cake (blondo. The results showed that pressure and time of circulating variables gave impact to the yield. On optimum variables, 2 atm pressure and 15 minutes of circulating gave better results with 97% yield. This operating variables also affecting oil quality. The minimum water content is 0.1%, free fatty acid is 0.18% and peroxide value is 2 mg/kg eq. The results showed that all of parameters meet the SNI standard.

Comparison of 3 estimation methods of mycophenolic acid AUC based on a limited sampling strategy in renal transplant patients.

Science.gov (United States)

Hulin, Anne; Blanchet, Benoît; Audard, Vincent; Barau, Caroline; Furlan, Valérie; Durrbach, Antoine; Taïeb, Fabrice; Lang, Philippe; Grimbert, Philippe; Tod, Michel

2009-04-01

A significant relationship between mycophenolic acid (MPA) area under the plasma concentration-time curve (AUC) and the risk for rejection has been reported. Based on 3 concentration measurements, 3 approaches have been proposed for the estimation of MPA AUC, involving either a multilinear regression approach model (MLRA) or a Bayesian estimation using either gamma absorption or zero-order absorption population models. The aim of the study was to compare the 3 approaches for the estimation of MPA AUC in 150 renal transplant patients treated with mycophenolate mofetil and tacrolimus. The population parameters were determined in 77 patients (learning study). The AUC estimation methods were compared in the learning population and in 73 patients from another center (validation study). In the latter study, the reference AUCs were estimated by the trapezoidal rule on 8 measurements. MPA concentrations were measured by liquid chromatography. The gamma absorption model gave the best fit. In the learning study, the AUCs estimated by both Bayesian methods were very similar, whereas the multilinear approach was highly correlated but yielded estimates about 20% lower than Bayesian methods. This resulted in dosing recommendations differing by 250 mg/12 h or more in 27% of cases. In the validation study, AUC estimates based on the Bayesian method with gamma absorption model and multilinear regression approach model were, respectively, 12% higher and 7% lower than the reference values. To conclude, the bicompartmental model with gamma absorption rate gave the best fit. The 3 AUC estimation methods are highly correlated but not concordant. For a given patient, the same estimation method should always be used.

Application of the AHP method to analyze the significance of the factors affecting road traffic safety

Directory of Open Access Journals (Sweden)

Justyna SORDYL

2015-06-01

Full Text Available Over the past twenty years, the number of vehicles registered in Poland has grown rapidly. At the same time, a relatively small increase in the length of the road network has been observed. As a result of the limited capacity of available infrastructure, it leads to significant congestion and to increase of the probability of road accidents. The overall level of road safety depends on many factors - the behavior of road users, infrastructure solutions and the development of automotive technology. Thus the detailed assessment of the importance of individual elements determining road safety is difficult. The starting point is to organize the factors by grouping them into categories which are components of the DVE system (driver - vehicle - environment. In this work, to analyze the importance of individual factors affecting road safety, the use of analytic hierarchy process method (AHP was proposed. It is one of the multi-criteria methods which allows us to perform hierarchical analysis of the decision process, by means of experts’ opinions. Usage of AHP method enabled us to evaluate and rank the factors affecting road safety. This work attempts to link the statistical data and surveys in significance analysis of the elements determining road safety.

DISCUSSION METHODS: MODIFICATION AND TRANSFORMATION

Directory of Open Access Journals (Sweden)

Abbasova, A.A.

2016-03-01

Full Text Available This article is about how to the importance of selecting the optimal methods of stimulation and motivation to learn. In modern conditions it is very important that the teacher gave the students ready knowledge, and pointed the way for the acquisition of knowledge, taught to acquire knowledge. This requires the selection of effective forms of language and literature work with texts of different types and styles of speech, listening, speaking. In this regard, special attention should be given lessons of speech development. There is a special group of methods to stimulate the development of communicative competence. Among them, and the method of discussion, which is increasingly being used in the classroom in the Russian language

The Montessori Method

Directory of Open Access Journals (Sweden)

Cathleen HASKINS

2010-12-01

Full Text Available Dr. Maria Montessori provided the world with a powerful philosophy and practice for the advancement of humanity: change how we educate children and we change the world. She understood two things very clearly: One, that we can build a better world, a more just and peaceful place, when we educate for the realization of the individual and collective human potential; and two, that the only way to create an educational system that will that will serve this end is to scrap the current system entirely and replace it with a completely new system. She gave us a system through which to accomplish that goal: The Montessori Method. The following is a personal and professional account of the Montessori Method of educating children.

Slope Stability Assessment Using Trigger Parameters and SINMAP Methods on Tamblingan-Buyan Ancient Mountain Area in Buleleng Regency, Bali

Directory of Open Access Journals (Sweden)

I Nengah Sinarta

2017-10-01

Full Text Available The mapping of soil movement was examined by comparing an extension of the deterministic Soil Stability Index Mapping (SINMAP method, and an overlay method with trigger parameters of soil movement. The SINMAP model used soil parameters in the form of the cohesion value (c, internal friction angle (φ, and hydraulic conductivity (ks for the prediction of soil movement based on the factor of safety (FS, while the indirect method used a literature review and field observations. The weightings of soil movement trigger parameters in assessments were based on natural physical aspects: (1 slope inclination = 30%; (2 rock weathering = 15%; (3 geological structure = 20%; (4 rainfall = 15%; (5 groundwater potential = 7%; (6 seismicity = 3%; and (7 vegetation = 10%. The research area was located in the Buleleng district, in particular in the ancient mountain area of Buyan-Tamblingan, in the Sukasada sub-district. The hazard mapping gave a high and very high hazard scale. The SINMAP model gave a validation accuracy of 14.29%, while the overlay method with seven trigger parameters produced an accuracy of 71.43%. Based on the analysis of the very high and high hazard class and the validation of the landslide occurrence points, the deterministic method using soil parameters and water absorption gave a much lower accuracy than the overlay method with a study of soil motion trigger parameters.

A Study of Layout, Rendering, and Interaction Methods for Immersive Graph Visualization.

Science.gov (United States)

Kwon, Oh-Hyun; Muelder, Chris; Lee, Kyungwon; Ma, Kwan-Liu

2016-07-01

Information visualization has traditionally limited itself to 2D representations, primarily due to the prevalence of 2D displays and report formats. However, there has been a recent surge in popularity of consumer grade 3D displays and immersive head-mounted displays (HMDs). The ubiquity of such displays enables the possibility of immersive, stereoscopic visualization environments. While techniques that utilize such immersive environments have been explored extensively for spatial and scientific visualizations, contrastingly very little has been explored for information visualization. In this paper, we present our considerations of layout, rendering, and interaction methods for visualizing graphs in an immersive environment. We conducted a user study to evaluate our techniques compared to traditional 2D graph visualization. The results show that participants answered significantly faster with a fewer number of interactions using our techniques, especially for more difficult tasks. While the overall correctness rates are not significantly different, we found that participants gave significantly more correct answers using our techniques for larger graphs.

Quantification of massively parallel sequencing libraries - a comparative study of eight methods

DEFF Research Database (Denmark)

Hussing, Christian; Kampmann, Marie-Louise; Mogensen, Helle Smidt

2018-01-01

Quantification of massively parallel sequencing libraries is important for acquisition of monoclonal beads or clusters prior to clonal amplification and to avoid large variations in library coverage when multiple samples are included in one sequencing analysis. No gold standard for quantification...... estimates followed by Qubit and electrophoresis-based instruments (Bioanalyzer, TapeStation, GX Touch, and Fragment Analyzer), while SYBR Green and TaqMan based qPCR assays gave the lowest estimates. qPCR gave more accurate predictions of sequencing coverage than Qubit and TapeStation did. Costs, time......-consumption, workflow simplicity, and ability to quantify multiple samples are discussed. Technical specifications, advantages, and disadvantages of the various methods are pointed out....

Comparison of green method for chitin deacetylation

Science.gov (United States)

Anwar, Muslih; Anggraeni, Ayu Septi; Amin, M. Harisuddin Al

2017-03-01

Developing highly environmentally friendly and cost-effective approaches for the chitosan production has paramount important in the future technology. Deacetylation process is one of the most importing steps to classify the quality of chitosan. This research aimed to study the best method for deacetylation of chitin considered by several factors like the concentration of base, temperature, time and reaction method. From the green chemistry point of view, conventional refluxing method relatively wasted energy compared to another method such as maceration, grinding and sonication. The degree of deacetylation (DD) of chitosan was studied by sonication, resulted in slightly increasing of DD from 73.14 to 73.28% during the time from 0.5 h to 1 h. Deacetylation of chitin with various sodium hydroxide concentration 60, 70 and 80% gave 73.14, 76.36 and 77.88% of DD, respectively. Variation of temperature at 40, 60, and 80 °C was slightly affected on increasing DD from 67.53, 72.84 and 73.14%, respectively. The DD of chitosan significantly increased from 60.19, 74.27 and 81.20% respectively correspondent to varying NaOH concentration 60, 70 and 80% using the maceration method. Solid phase grinding method for half hour resulted in 79.49% of DD. The application of ultrasound grinding method not only was enhanced toward the deacetylation but also favoured the depolymerization process. Moreover, maceration for 7 days with 80% NaOH can be as an alternative method.

Fibrinogen estimates are influenced by methods of measurement and hemodilution with colloid plasma expanders.

Science.gov (United States)

Fenger-Eriksen, Christian; Moore, Gary W; Rangarajan, Savita; Ingerslev, Jørgen; Sørensen, Benny

2010-12-01

Measurement of plasma fibrinogen is often required in critically ill patients or massively bleeding patients being resuscitated with colloid plasma expander. This study aimed at evaluating different assays of plasma fibrinogen after in vitro dilution with commonly used plasma expanders and challenged the hypothesis that levels of fibrinogen are estimated significantly higher in plasma diluted with colloid plasma expander compared with isotonic saline. Fibrinogen measurements were established in plasma samples each diluted in vitro to 30 or 50% with isotonic saline, hydroxyethyl starch (HES) 130/0.4, and human albumin. Fibrinogen levels were assessed using an antigen determination, three photo-optical Clauss methods, one mechanical Clauss method, a prothrombin-derived method, and viscoelastic measurement through thromboelastometry. Measurement of fibrinogen levels was significantly different when performed on alternate analytical platforms. By 30 and 50% dilution with HES 130/0.4 coagulation analyzers using the photo-optical Clauss methods significantly overestimated levels of fibrinogen. Dilution with human albumin did not affect fibrinogen levels except from one analyzer by 50% dilution level. Viscoelastic measurement of fibrin polymerization was reduced at both dilution levels and appeared to reflect the impairment of fibrin polymerization induced by HES 130/0.4 and to a lesser extent human albumin. This study demonstrated that different automated coagulation analyzers revealed significantly different levels of fibrinogen. The presence of colloid plasma expander gave rise to erroneous high levels of fibrinogen returned from some coagulation analyzers employing the method of Clauss. © 2010 American Association of Blood Banks.

An Efficient Method for Image and Audio Steganography using Least Significant Bit (LSB) Substitution

Science.gov (United States)

Chadha, Ankit; Satam, Neha; Sood, Rakshak; Bade, Dattatray

2013-09-01

In order to improve the data hiding in all types of multimedia data formats such as image and audio and to make hidden message imperceptible, a novel method for steganography is introduced in this paper. It is based on Least Significant Bit (LSB) manipulation and inclusion of redundant noise as secret key in the message. This method is applied to data hiding in images. For data hiding in audio, Discrete Cosine Transform (DCT) and Discrete Wavelet Transform (DWT) both are used. All the results displayed prove to be time-efficient and effective. Also the algorithm is tested for various numbers of bits. For those values of bits, Mean Square Error (MSE) and Peak-Signal-to-Noise-Ratio (PSNR) are calculated and plotted. Experimental results show that the stego-image is visually indistinguishable from the original cover-image when nsteganography process does not reveal presence of any hidden message, thus qualifying the criteria of imperceptible message.

Batch and flow-injection methods for the spectrophotometric determination of olanzapine

Energy Technology Data Exchange (ETDEWEB)

Jasinska, A.; Nalewajko, E

2004-04-22

An indirect batch spectrophotometric and direct flow-injection (FI) visible spectrophotometric methods have been developed for the determination of the novel anti-psychotic drug olanzapine (OLA). The batch method is based on the oxidation of olanzapine by a known excess of potassium hexacyanoferrate(III) in the presence of the mixture of sulphuric and phosphoric acids (1:1 (v/v)). The absorbance of unreacted oxidant is measured at 425 nm. The absorbance decreases linearly with increasing concentration of the assayed drug. The FI method with detection at 540 nm is based on the direct oxidation of olanzapine one of two oxidants, cerium(IV) sulphate or potassium hexacyanoferrate(III) in acidic medium. The calibration graph were linear over the range of 2.5-40 {mu}g ml{sup -1} in the batch method and 0.05-300 and 0.5-250 {mu}g ml{sup -1} in the FI methods, used cerium (IV) sulphate and potassium hexacyanoferrate (III) respectively. Both FI methods gave similar results in terms of precision and accuracy. The relative standard deviation (R.S.D.), was <1%. The accuracy, obtained from recovery experiments, was 97.9-99.4%. The batch method gave slightly higher R.S.D. values (up to 2.3%) and lower values of accuracy (the recovery was between 96.5 and 96.6%). The methods developed were applied to the determination of olanzapine in a pharmaceutical product.

Significance evaluation in factor graphs

DEFF Research Database (Denmark)

Madsen, Tobias; Hobolth, Asger; Jensen, Jens Ledet

2017-01-01

in genomics and the multiple-testing issues accompanying them, accurate significance evaluation is of great importance. We here address the problem of evaluating statistical significance of observations from factor graph models. Results Two novel numerical approximations for evaluation of statistical...... significance are presented. First a method using importance sampling. Second a saddlepoint approximation based method. We develop algorithms to efficiently compute the approximations and compare them to naive sampling and the normal approximation. The individual merits of the methods are analysed both from....... Conclusions The applicability of saddlepoint approximation and importance sampling is demonstrated on known models in the factor graph framework. Using the two methods we can substantially improve computational cost without compromising accuracy. This contribution allows analyses of large datasets...

Critical analysis of stability and performance of organometal halide perovskite solar cells via various fabrication method (Review

Directory of Open Access Journals (Sweden)

Suhaimi Suriati

2017-01-01

Full Text Available Organometal halide perovskite solar cells (Omh-PSCs have attracted attention due to its unique electrical and optical properties. Ideally, the Omh-PSCs should remain free from degradation under normal operating conditions for several years, preferably tens of years. In order to produce high power conversion efficiency with low potential of degradation, different fabrication methods have been developed. The reported stability of perovskite films can vary significantly and reported to decay substantially up to 20% of its original performance. A thorough understanding of fabrication process upon the stability of the device is regarded as crucial to pave the way for future endeavors. This review summarized and highlighted the recent research of fabrication methods that gave an impact to the stability of perovskite devices.

A novel PCR-based method to enumerate Salmonella in animal feed

DEFF Research Database (Denmark)

Löfström, Charlotta; Andersson, Gunnar; Häggblom, Per

2010-01-01

and pellets) only three gave results that differed between the PCR and MSRV methods. Ct values for naturally contaminated samples were higher compared to samples artificially contaminated with low numbers (approx. 2 CFU/25 g feed) of stressed Salmonella. To allow quantification of low numbers of Salmonella...

Implementation Research: A Significant Step in the Right Direction ...

African Journals Online (AJOL)

During my fellowship training, I was required to complete a hypothesis driven research in order to become eligible for board certification by the American Board of Pediatrics. I started the process by meeting with my mentor who asked me what type of research I was interested in. I gave him a little history of my background in ...

Lung lesion doubling times: values and variability based on method of volume determination

International Nuclear Information System (INIS)

Eisenbud Quint, Leslie; Cheng, Joan; Schipper, Matthew; Chang, Andrew C.; Kalemkerian, Gregory

2008-01-01

Purpose: To determine doubling times (DTs) of lung lesions based on volumetric measurements from thin-section CT imaging. Methods: Previously untreated patients with ≥ two thin-section CT scans showing a focal lung lesion were identified. Lesion volumes were derived using direct volume measurements and volume calculations based on lesion area and diameter. Growth rates (GRs) were compared by tissue diagnosis and measurement technique. Results: 54 lesions were evaluated including 8 benign lesions, 10 metastases, 3 lymphomas, 15 adenocarcinomas, 11 squamous carcinomas, and 7 miscellaneous lung cancers. Using direct volume measurements, median DTs were 453, 111, 15, 181, 139 and 137 days, respectively. Lung cancer DTs ranged from 23-2239 days. There were no significant differences in GRs among the different lesion types. There was considerable variability among GRs using different volume determination methods. Conclusions: Lung cancer doubling times showed a substantial range, and different volume determination methods gave considerably different DTs

Clinical significance of multiphase skeletal scintiscanning

International Nuclear Information System (INIS)

Zimmermann, P.

1984-01-01

A total of 61 patients were included in this study, which was performed to find out, if multiphase skeletal scintiscanning using 99mTc-DPD is a more accurate investigational method in terms of diagnostic differentiation than conventional scintiscanning. All patients were subjected to additional diagnostic procedures using X-rays, CT, etc. and the findings revealed were compared. In order to ensure an objective assessment of the density patterns obtained in the individual study phase (initial phase (1); vascular phase (2); soft tissue phase (3); standard phase (4)), special care was taken that only regions of similar vascularity were compared. In acute osteomyelitis, osteitis deformans according to Paget and osteoid osteoma multiphase scintiscanning yielded valuable additional information which, from the diagnostic point of view, proved to be much more meaningful than that provided by conventional scintiscanning, as very characteristic activity patterns were discernible in the initial study phases. In patients showing artificial limb infection or fractures this supplementary information was also found to be of some value, although the behaviour of activity in the initial study phases gave less conclusive evidence here than in the diseases mentioned before. In inflammatory disorders involving only minor histological changes or those of a chronic nature as well as in special forms of inflammation and artificial limb dislocation multiphase scintiscanning was not found to offer any advantages over conventional scintiscanning. (TRV) [de

Applicability of isotopic dilution methods for determination of the zinc supplying capacity of some Indian soils

International Nuclear Information System (INIS)

Iyengar, B.R.V.; Deb, D.L.

1975-01-01

The applicability of the isotopic dilution methods to determine the zinc supplying capacity of some Indian soils belonging to three soil groups was studied using 65 Zn. In these soils 'L' values determined by the pot culture method and the 'E' values by equilibration in soil suspensions by the carrier free and carrier methods and using chemical extractants DTPA-CaCl 2 -NaOAc and EDTA-NH 4 OAc were compared. The 'L' values were significantly correlated with zinc uptake by maize and also with zinc extracted by a number of chemical extractants. The laboratory determinations 'E' values by isotopic exchange equilibria in soil suspension both with and without carrier zinc led to over estimates and gave grossly exggerated values of 'labile zinc' especially in alkaline and high zinc 'fixing' soils. The 'E' values determined in both DTPA-CaCl 2 -NaOAc and EDTA-NH 4 OAc correlated significantly with zinc uptake by maize. These values agreed well with 'L' values and 'available' zinc determined by chemical soil tests. (author)

Serum Copper Level Significantly Influences Platelet Count, Lymphocyte Count and Mean Cell Hemoglobin in Sickle Cell Anemia

Directory of Open Access Journals (Sweden)

Okocha Chide

2015-12-01

Full Text Available Background Changes in serum micro nutrients levels affect a number of critically important metabolic processes; these could potentially influence blood counts and ultimately disease presentation in patients with sickle cell anemia (SCA. Objectives To evaluate the influence of serum micro-nutrients levels; zinc, copper, selenium and magnesium on blood counts in steady state SCA patients. Methods A cross sectional study that involved 28 steady state adult SCA subjects. Seven milliliters (mls of blood was collected; 3 mls was for hemoglobin electrophoresis and full blood count determination while 4 mls was for measurement of serum micro nutrients levels, by the atomic absorption spectrophotometry. Correlation between serum micro-nutrient levels and blood counts was done by the Pearson’s linear regression. Ethical approval was obtained from the institutional review board and each participant gave informed consent. All data was analyzed by SPSS software version 20. Results There was a significant correlation between serum copper levels and mean cell hemoglobin (MCH, platelet and lymphocyte counts (r = 0.418; P = 0.02, r = -0.376; P = 0.04 and r = -0.383; P = 0.04, respectively. There were no significant correlations between serum levels of other micro nutrients (selenium, zinc and magnesium and blood counts. Conclusions Copper influences blood count in SCA patients probably by inducing red cell haemolysis, oxidant tissue damage and stimulating the immune system.

Significances and meanings of the musical identity of patients and relatives receiving oncological palliative care

Directory of Open Access Journals (Sweden)

Vladimir Araujo de Silva

2014-03-01

Full Text Available This phenomenological study was structured on Heidegger’s theoretical-philosophical framework, with the objective of unveiling the significances and meanings of the musical identity of patients and relatives under oncological palliative care. Individual interviews were performed with 12 clients (seven patients and five relatives staying at the support residence of the Maringa Female Network Against Cancer. A total of eight musical meetings were performed between January and February of 2011. I understood that the musical identity of the evidenced beings refers to the religious and country music styles, that their significances and meanings are connected to their spirituality and the significant events of their historicity, and that their mood and reflection intermediated by music can influence their musical choice. I gave evidence to the need to consider the music identity and empowerment in musical choices, which carries existential, social, cultural, spiritual and family aspects as qualifying elements of nursing in palliative care. Descriptors: Nursing Care; Oncology Nursing; Music; Music Therapy; Palliative Care.

Thermal and Isothermal Methods in Development of Sustained Release Dosage Forms of Ketorolac Tromethamine

Directory of Open Access Journals (Sweden)

Dimple Chopra

2008-01-01

Full Text Available Differential scanning calorimetry (DSC is a rapid and convenient and conclusive method of screening drug-polymer blend during preformulation studies as it allows polymer incompatibility to be established instantaneously. Various batches of matrix tablets of ketorolac tromethamine (KTM with a series of compatible polymers were prepared. Batches of tablets which gave desired sustained release profile were subjected to stability testing according to ICH guidelines. The analysis for drug content was done using high performance liquid chromatography (HPLC method. The results revealed that there was no statistically significant change in drug content after storage of matrix tablets at elevated temperature of 40°C and 75% relative humidity. From our study we conclude that with careful selection of different polymers and their combinations, a stable sustained release oral dosage form of ketorolac tromethamine can be achieved.

Para-aminobenzoic acid used as a marker for completeness of 24 hour urine: Assessment of control limits for a specific HPLC method

DEFF Research Database (Denmark)

Jakobsen, Jette; Ovesen, L.; Fagt, Sisse

1997-01-01

(20-59 y; n = 34) PABA was taken as recommended, whereas in the older age group (60-80 y; n = 22) the last PABA dosage was advanced three hours. Results: Protocol 1: HPLC gave significantly lower PABA recovery results compared to colorimetry, the difference between methods being 23.9 +/- 5.5 mg/24 h...... in a complete 24 h urine differs from the limit based on colorimetry. This study found a limit of 187 mg/24 h corresponding to the lower 95% confidence limit for a single subject....

Effect of Pre-treatment method on the Hydrolysis of Corn cob and Sawdust

Directory of Open Access Journals (Sweden)

Olawole Ogirima Olanipekun

2016-12-01

Full Text Available Efficient pre-treatment has been found to be crucial step before enzymatic hydrolysis of cellulose into fuels or chemicals. As a result various pretreatment methods have been developed to facilitate these bio-conversion processes, and this research focuses on the effect of two pretreatment methods such as liquid hot water and sulphuric acid pre-treatment to remove some of the components like lignin and hemicellulose which form structural barrier to enzymatic accessibility of cellulose in corn cobs and sawdust. The cellulosic materials were first dried in oven at 65 oC for 24 hours,  and using   solid to liquid ratio of 1:10, the two methods were carried out at resident times ranging from 10 - 40 minutes. The liquid hot water method involved heating the cellulosic materials in water at 120 oC and 1atmosphere in a pressure vessel, and for the second method, the dried cellulosic materials were refluxed in 5 % sulphuric acid at a temperature of 120 oC. Pretreated samples were filtered and liquid fractions were analyzed for the presence of reducing sugars, while solid residues were dried in the oven and weighed to measure the mass lost during pretreatment as a pointer to lignin breakdown. It was observed that the mass lost increased with time for both pretreatment methods, but the liquid hot water pretreatment gave higher lignin and hemicellulose removal when compared to the sulphuric acid pre-treatment. The pretreated materials were hydrolyzed with two combinations of commercial enzymes namely cellulase/ hemicellulase and cellulase/β glucosidase. The reducing sugar was measured using Dinitrosalycilic acid (DNSA method and the sugar yields from corn cobs were higher than that of sawdust when subjected to similar process conditions, and the enzyme combination of cellulase/glucosidase gave higher yields of reducing sugars.  A model equation which describes the hydrolysis process was developed from first principles and the experimental data

Comparison of dynamic compensation methods for delayed self-powered neutron detector

International Nuclear Information System (INIS)

In, Wang Kee; Kim, Joon Sung; Auh, Geun Sun; Yoon, Tae Young

1993-01-01

Dynamic compensation methods for rhodium self-powered neutron detector have been developed by Banda and Hoppe to compensate for the time delay associated with detector signals. The time delay is due to the decay of the neutron-activated rhodium and results in delayed detector response. Two digital dynamic compensation methods, were compared for step change of neutron flux in this paper. The inverse kinetics method gave slightly better response time and noise gain. However, the inverse kinetics method also showed overshooting of neutron flux for the step change. (Author)

Strategic Management: An Evaluation of the Use of Three Learning Methods.

Science.gov (United States)

Jennings, David

2002-01-01

A study of 46 management students compared three methods for learning strategic management: cases, simulation, and action learning through consulting projects. Simulation was superior to action learning on all outcomes and equal or superior to cases on two. Simulation gave students a central role in management and greater control of the learning…

Thyroid function in mothers who gave birth to neonates with transient congenital hypothyroidism

International Nuclear Information System (INIS)

Karam, G.A.; Hakimi, H.; Rezaeian, M.; Gafarzadeh, A.; Rashidinejad, H.; Khaksari, M.

2009-01-01

Objective: To determine the thyroid status of mother's of newborns with primary congenital hypothyroidism. Methodology: Thyroid function tests were carried out on 80 mothers of hypothyroid newborns and 80 mothers of non-hypothyroid newborns as control. Results: The mean difference of the tests revealed that mothers of congenitally hypothyroid infants had a lower triiodothyronine resin uptake (T3RU) concentrations compared with the control population. The higher value of free thyroxin index (FTI) in case group showed a tendency to significance. The proportional frequency distribution showed; T3RU and triiodothyronine (T3) had a significant difference, and FTI showed a tendency to significance. There were no significant differences between; thyroid-stimulating hormone (TSH), thyroxine (T4) and anti-thyroid peroxidase antibodies (anti-TPO) in two groups. Conclusions: These results indicated that at least some cases of primary congenital hypothyroidism were attributable to the maternal thyroid disease. Therefore, we recommend that each pregnant woman should be assessed for thyroid function in region with a high prevalence of thyroid disease. (author)

Current lipid extraction methods are significantly enhanced adding a water treatment step in Chlorella protothecoides.

Science.gov (United States)

Ren, Xiaojie; Zhao, Xinhe; Turcotte, François; Deschênes, Jean-Sébastien; Tremblay, Réjean; Jolicoeur, Mario

2017-02-11

helps the subsequent release of intracellular lipids in the second extraction step, thus improving the global lipids extraction yield. In addition, the water treatment positively modifies the intracellular lipid class ratios of the final extract, in which TAG ratio is significantly increased without changes in the fatty acids composition. The novel method thus provides an efficient way to improve lipid extraction yield of existing methods, as well as selectively favoring TAG, a lipid of the upmost interest for biodiesel production.

Method optimization of ocular patches

Directory of Open Access Journals (Sweden)

Kamalesh Upreti

2012-01-01

Full Text Available The intraocular patches were prepared using gelatin as the polymer. Ocular patch were prepared by solvent casting method. The patches were prepared for six formulations GP1, GP2, GP3, GP4, GP5 and GP6. Petri dishes were used for formulation of ocular patch. Gelatin was used as a polymer of choice. Glutaraldehyde used as cross linking agent and (DMSO dimethylsulfoxide used as solubility enhancer. The elasticity depends upon the concentration of gelatin. 400 mg amount of polymer i.e gelatin gave the required elasticity for the formulation.

Comparative analysis of environmental DNA extraction and purification methods from different humic acid rich soils

CSIR Research Space (South Africa)

Lakay, FM

2007-01-01

Full Text Available Three different soil DNA isolation and four purification strategies were compared on different soil samples with variable rates of success. Bead beating extraction gave significantly higher DNA yields than microwave-based and liquid nitrogen...

[3H]Leucine incorporation method as a tool to measure secondary production by periphytic bacteria associated to the roots of floating aquatic macrophyte.

Science.gov (United States)

Miranda, M R; Guimarães, J R D; Coelho-Souza, A S

2007-10-01

The present study assessed the application of [(3)H]Leucine incorporation into protein by periphytic bacteria associated with the roots of the floating aquatic macrophyte Eichornia crassipes. Basic assumptions underlying the method, such as linearity of leucine incorporation, saturation level of incorporation rates, incorporation into other macromolecules, specificity of incorporation for bacterial assemblages and [(3)H]Leucine degradation during samples storage were tested, and two procedures for extracting the incorporated leucine were compared. Both methods gave the same results, however, the hot TCA extraction method was less time consuming than the alkaline extraction method. Incorporation of [(3)H]Leucine was linear for up to 40 min. Saturation concentration of [(3)H]Leucine incorporation into protein was 1500 nM. An experiment with prokaryotic and eukaryotic inhibitors showed no significant [(3)H]Leucine incorporation into eukaryotes even in high leucine concentrations. No significant amounts of radiolabel were incorporated into other macromolecules. The maximum time of sample storage after the incubation is 15 days. The leucine incorporation method can be a reliable tool to measure bacterial production in the periphyton root-associated bacteria.

Plants Africa gave to the World

Directory of Open Access Journals (Sweden)

G. Kunkel

1983-11-01

Full Text Available Although the flora of Africa is rather poor in plant species when compared to the floras of Tropical America or South-east Asia, this vast continent is the home of a wide range of plants useful to Man. Many of these have become famous in cultivation around the world. Coffee now provides an important source of income for certain countries, and the Yams yield one of the world’s staple foods. The Oil Palm and Cola trees are widely cultivated in Africa itself and elsewhere. African Mahoganies and Ironwoods are much sought after timber trees of excellent quality. Numerous grasses and pulses are well-known for their food value, and some of the native Cucurbitaceae are appreciated additions to our vegetable diet. African plants have also made their contribution to horticulture, ranging from world-famous trees such as the African or Gabon Tulip tree and many of the South African species of Proteaceae to the multitude of East and South African succulents. The present paper provides a survey of the most important of these useful plants and will emphasize the need of further research for forestry and agricultural as well as horticultural purposes, especially as far as some still little-known but potentially important plants species are concerned.

They gave their names to science

National Research Council Canada - National Science Library

Halacy, D. S

1967-01-01

...: Ernst Mach and his number, Gergor Mendel and his laws, Christian Johann Doppler and his effect, Hans Geiger and his radiation counter, Nicholas Sadi Carnot and thermodynamics, Gustave, Gaspard de...

Suitability of the thermoluminescence method for detection of irradiated foods

International Nuclear Information System (INIS)

Pinnioja, S.

1993-01-01

Irradiated foods can be detected by thermoluminescence (TL) of contaminating minerals. Altogether about 300 lots of herbs, spices, berries, mushrooms and seafood were studied by the TL method. Irradiated herbs and spices were easily differentiated from unirradiated ones two years after irradiation of a 10 kGy dose. The mineral composition of seafood was variable; and while calcite was suitable for the TL analysis, aragonite and smectite gave unreliable results. Control analyses during two years confirmed the reliability of TL method. (author)

Direct seeding of Sitka spruce (Picea sitchensis (Bong.) Carr.), lodgepole pine (Pinus Contorta Dougl. v. contorta) and Siberian larch (Larix sibirica Ledeb.), on scarified seed spots in southern Iceland, using various methods

Energy Technology Data Exchange (ETDEWEB)

Petursson, J.G. [The Icelandic Forestry Association, Reykjavik (Iceland)

1995-12-31

Field experiments were established to study the potential of direct seeding of Sitka spruce, lodgepole pine and Siberian larch in southern Iceland. Five seeding methods were tried; control, covered with gravel, covered with pumice, pyramidal indentations and plastic cone. Spring- and autumn planting of one year old planting stock was also carried out for comparison. The results after two growing seasons are presented. Overall germination was 11,3% the first summer and 19,0% the second summer. Lodgepole pine had significantly highest germination or 41,3%. Sitka spruce, having 26.8% germination, and Siberian larch having 22,6% germination did not differ significantly from each other. The seeding method plastic cone gave the highest germination for all the species used, or 50,3%. Seedling mortality was high after the first winter, except in the plastic cone where more than 80% of the seedlings survived. The number of spots having at least one living seedling after two growth seasons was high in all seeding methods for lodgepole pine or 76,3-95,0% and for Sitka spruce or 71,3-86,3%. This result was however mainly explained by seedlings that germinated in the current growing season. For Siberian larch the number of the spots having one or more living seedlings was low for other seeding methods than plastic cone which gave 68,8%. No difference was found in seedling height between the methods control, covered with gravel, covered with pumice and pyramidal indentations. Survival of planted seedlings differed between planting times. Spring planting (28/6) was found more advantageous for Sitka spruce and lodgepole pine, but autumn planting (3/10) for Siberian larch. When the seeding methods were compared with planting after two growth seasons, it can be concluded that the method plastic cone was the only method tried which was compatible with planting. 45 refs, 9 figs, 14 tabs

Methods for significance testing of categorical covariates in logistic regression models after multiple imputation: power and applicability analysis

NARCIS (Netherlands)

Eekhout, I.; Wiel, M.A. van de; Heymans, M.W.

2017-01-01

Background. Multiple imputation is a recommended method to handle missing data. For significance testing after multiple imputation, Rubin’s Rules (RR) are easily applied to pool parameter estimates. In a logistic regression model, to consider whether a categorical covariate with more than two levels

Features of Somatic and Reproductive Status of Women, who Gave Birth to a Child with Congenital Malformations, and Their Identifiсation Using «Case — Control» Method According to Data of Lviv Regional Clinical Perinatal Center in 2007–2009

Directory of Open Access Journals (Sweden)

Zborovska N.V. Zborovska N.V.

2012-04-01

While comparing a range of reproductive anamnesis indices there was noticed a higher percentage of dead children, stillbirths, anemia in pregnancy, gestosis in the first half of pregnancy, gestosis in the second half of pregnancy, abnormal labors in mothers who gave birth to a child with congenital malformations than in women of control group. According to ultrasound diagnosis congenital abnormalities in pregnancy were detected in 31.6 % of cases. There were diagnosed 4 cases of Arnold — Chiari syndrome (spina bifida and internal hydrocephalus; and 3 cases of each: hydrocephalus, gastroschisis, small intestinal atresia, and 2 cases of each: congenital malformations, hypoplastic left heart syndrome, Down’s syndrome, congenital diaphragmatic hernia, omphalocele, congenital rectal atresia, and 1 case of each: spina bifida, congenital absence of forearm and hand, left ventricular rabdomioma, encephalocele.

Scottish immunoassay support service quality control scheme for thyroxine, triiodothyronine, and digoxin assays: analysis of first 18 months' experience

International Nuclear Information System (INIS)

Ratcliffe, W.A.; Logue, F.C.; Ratcliffe, J.G.

1978-01-01

Initial experience of the Scottish Immunoassay Support Service Quality Control scheme for thyroxin(T4), triiodothyronine (T3), and digoxin is analysed. For T4, radioimmunoassay (RIA) methods gave values close to the all-method mean. Competitive protein binding (CPB) kits gave values significantly higher (by 12%) in one and lower (by 10%) in another, probably due to the extraction of interfering substances such as non-esterified fatty acids or thyroid hormone binding proteins. The range of between-batch precision of individual laboratories was 10.8-47.5% (mean 17.8%) over the clinically relevant range. It was particularly poor at levels below the lower limit of the normal range. For T3 RIA, kit methods gave significantly higher values than independent methods although recovery of exogenous T3 was approximately quantitative with both. Cross reaction of T4 in T3 assays was insignificant. The range of between-batch precision for individual laboratories was 11.4-35.5% (mean 21.9%), and was poorest at levels of 1 nmol/l or less. For digoxin RIA, Lanoxitest γ gave significantly higher values than other methods, and over-recovered exogenous digoxin. The range of between-batch precision was 13.8-35.2% (mean 21.6%), and was poorest at levels of 1 nmol/l or less. The distribution of liquid human serum specimens at ambient temperature was satisfactory for quality control of T4, T3, and digoxin RIA but not for T4 by the Thyopac 4 method. Ox serum was unsuitable for certain T4 RIA methods. (author)

Design of calibration method in neutron and individual dosimeter

International Nuclear Information System (INIS)

Belkhodia, M.

1984-12-01

Usually albedo dosemeters are calibrated with beam of monoenergetic neutrons. Since neutron energy around neutron sources varies greatly, we applied the calibration method to a mixed field whose energy spectrum lies between 0.025 ev and 10 Mev. The method is based on a mathematical model that deals with the dosimeter response as a function at the neutron energy. The measurements carried out with solid state nuclear track detectors show the dosimeter practical aspect. The albedo dosimeter calibration gave results on good agreement with the international institution recommendations

Solubility and transport of arsenic coal ash

International Nuclear Information System (INIS)

Iturbe, R.; Cruickshank, C.; Vega, E.; Silva, A.E.

1996-01-01

An experimental method combined with a numerical model allows a comparison of two methods for the disposal of ash that contains arsenic, from the Rio Escondido coal-fired power plant. The calculation yields significant differences in aquifer migration times for the site. The wet disposal method gave 10 years time and the dry method gave 22 years. Experiments were performed on the rate of dissolution of the arsenic from ash samples; and these results indicate a first order kinetics reaction. 8 refs., 8 figs., 8 tabs

A new method to detect significant basal body temperature changes during a woman's menstrual cycle.

Science.gov (United States)

Freundl, Günter; Frank-Herrmann, Petra; Brown, Simon; Blackwell, Leonard

2014-10-01

To compare the results of a computer programme based on the Trigg's tracking system (TTS) identification of the basal body temperature (BBT) shift day from daily records of BBT values (TTS transition day), with the BBT shift day identified from the same records using the Sensiplan(®) symptothermal method of natural family planning. A computer programme was written to display the daily BBT readings for 364 menstrual cycles from 51 women aged 24 to 35 years, obtained from the German Natural Family Planning (NFP) database. The TTS transition day so identified from each record was then compared with the BBT shift day estimated from the same record by the Sensiplan(®) method. Total agreement between the methods was obtained for 81% (294/364) of the cycles and 18% (67) cycles differed by ± 1 day. For the 364 pairs of values distributed among 51 women the medians of the differences between the TTS transition day and Sensiplan(®) initial day of the BBT rise (shift day) were not significantly different (χ(2) = 65.28, df = 50, p = 0.07205). The advantages of the tracking signal algorithm are that in many cases it was possible to identify the BBT shift day on that very day - rather than only some days later - and to estimate the probability that a transition had occurred from the different values of the tracking signal.

New method for GC/FID and GC-C-IRMS analysis of plasma free fatty acid concentration and isotopic enrichment.

Science.gov (United States)

Kangani, Cyrous O; Kelley, David E; Delany, James P

2008-09-15

A simple, direct and accurate method for the determination of concentration and enrichment of free fatty acids (FFAs) in human plasma was developed. The validation and comparison to a conventional method are reported. Three amide derivatives, dimethyl, diethyl and pyrrolidide, were investigated in order to achieve optimal resolution of the individual fatty acids. This method involves the use of dimethylamine/Deoxo-Fluor to derivatize plasma free fatty acids to their dimethylamides. This derivatization method is very mild and efficient, and is selective only towards FFAs so that no separation from a total lipid extract is required. The direct method gave lower concentrations for palmitic acid and stearic acid and increased concentrations for oleic acid and linoleic acid in plasma as compared to methyl ester derivative after thin-layer chromatography. The [(13)C]palmitate isotope enrichment measured using direct method was significantly higher than that observed with the BF(3)/MeOH-TLC method. The present method provided accurate and precise measures of concentration as well as enrichment when analyzed with gas chromatography combustion-isotope ratio-mass spectrometry.

Albedo's determination by the method of neutron impulse

International Nuclear Information System (INIS)

Flores Calderon, J.E.

1982-01-01

Experiments with non-stationary neutron transport in large cavity moderators (l>>Σsub(tr) -1 ) (where l is the characteristic cavity length and Σsub(tr) -1 the macroscopic transport section of the moderator) led to the method reported in this study which, based on neutron impulses for determining albedo of thermal neutrons, gave a precision greater by an order of magnitude over previous methods. A sufficient time interval after introduction of the neutron flux into the moderator chamber decreased exponentially the decay constant L, which was itself related to albedo by a function called f. Numerical calculations of albedo were assisted. (author)

Difference in method of administration did not significantly impact item response

DEFF Research Database (Denmark)

Bjorner, Jakob B; Rose, Matthias; Gandek, Barbara

2014-01-01

assistant (PDA), or personal computer (PC) on the Internet, and a second form by PC, in the same administration. Structural invariance, equivalence of item responses, and measurement precision were evaluated using confirmatory factor analysis and item response theory methods. RESULTS: Multigroup...... levels in IVR, PQ, or PDA administration as compared to PC. Availability of large item response theory-calibrated PROMIS item banks allowed for innovations in study design and analysis.......PURPOSE: To test the impact of method of administration (MOA) on the measurement characteristics of items developed in the Patient-Reported Outcomes Measurement Information System (PROMIS). METHODS: Two non-overlapping parallel 8-item forms from each of three PROMIS domains (physical function...

Radioimmunoassay for serum cortisol with 125I-labeled ligand: comparison of three methods

International Nuclear Information System (INIS)

Kumar, M.S.; Safa, A.M.; Deodhar, S.D.

1976-01-01

We evaluated a previously modified double-antibody radioimmunoassay for serum cortisol. It was compared with the conventional double-antibody method that includes the usual extraction step, and also with an antibody-coated tube method. In this modified method, cortisol was released from its binding globulin by enzymatic degradation rather than by extraction with ether, and a preincubated mixture of first and second antibody was used to separate antibody-bound cortisol from free. These two steps shortened total assay time significantly. Results still correlated well (r = 0.87) with results by the conventional method, but the antibody-coated tube method gave lower results (r = 0.61). Because of its good correlation with the conventional method, this method was thought to be more accurate. In 52 normal subjects, mean cotrtisol concentrations at 0800 and 1700 hours were 161 +/- 52 (SD) mug/liter and 91 +/-- 27 mug/liter, respectively. In 16 normal subjects, cortisol values before and after dexamethasone treatment (1 mg at midnight) were 134 +/-- 53 mug/liter and less than 20 mug/liter. In the same subjects, cortisol concentrations before and 30 min and 60 min after Cortrosyn (synthetic corticotropin 1-24, 0.25 mg) administration were 103 +/-- 25, 205 +/-- 45 and 223 +/-- 51 mug/liter, respectively

Comparing alternative methods for holding virgin honey bee queens for one week in mailing cages before mating.

Directory of Open Access Journals (Sweden)

Gianluigi Bigio

Full Text Available In beekeeping, queen honey bees are often temporarily kept alive in cages. We determined the survival of newly-emerged virgin honey bee queens every day for seven days in an experiment that simultaneously investigated three factors: queen cage type (wooden three-hole or plastic, attendant workers (present or absent and food type (sugar candy, honey, or both. Ten queens were tested in each of the 12 combinations. Queens were reared using standard beekeeping methods (Doolittle/grafting and emerged from their cells into vials held in an incubator at 34C. All 12 combinations gave high survival (90 or 100% for three days but only one method (wooden cage, with attendants, honey gave 100% survival to day seven. Factors affecting queen survival were analysed. Across all combinations, attendant bees significantly increased survival (18% vs. 53%, p<0.001. In addition, there was an interaction between food type and cage type (p<0.001 with the honey and plastic cage combination giving reduced survival. An additional group of queens was reared and held for seven days using the best method, and then directly introduced using smoke into queenless nucleus colonies that had been dequeened five days previously. Acceptance was high (80%, 8/10 showing that this combination is also suitable for preparing queens for introduction into colonies. Having a simple method for keeping newly-emerged virgin queens alive in cages for one week and acceptable for introduction into queenless colonies will be useful in honey bee breeding. In particular, it facilitates the screening of many queens for genetic or phenotypic characteristics when only a small proportion meets the desired criteria. These can then be introduced into queenless hives for natural mating or insemination, both of which take place when queens are one week old.

Labelling of blood cells with radioactive indium-201: method, results, indications

International Nuclear Information System (INIS)

Ducassou, D.; Brendel, A.; Nouel, J.P.

1978-01-01

A modification of the method of Thakur et al. for labelling polynuclear cells with 8-hydroxyquinolein-indium-complexe utilising the water soluble sulfate of the substance was applied. The labelling procedure gave a yield over 98% with erthrocytes and over 80% with platelets and polynuclear cells using at least 1 x 10 8 plasma free cells. Functional capacity of the labelled cells remained unaltered. Injection double labelled ( 111 In, 51 Cr) red cells correlation of values for the red cell volume amounted to r = 0,98 (n=20); red cell life-spane measurements gave comparable results in 5 patients. After injecting labelled platelets a life-spane between 6,5 and 11 days was measured. Scintigraphic visualisation of pulmonary embolism was obtained 30 minutes after injecting labelled platelets. Injection of labelled polynuclear cells allows life-spane measurements as well as detection of abscesses. (author)

Performance assessment of semiempirical molecular orbital methods in describing halogen bonding: quantum mechanical and quantum mechanical/molecular mechanical-molecular dynamics study.

Science.gov (United States)

Ibrahim, Mahmoud A A

2011-10-24

The performance of semiempirical molecular-orbital methods--MNDO, MNDO-d, AM1, RM1, PM3 and PM6--in describing halogen bonding was evaluated, and the results were compared with molecular mechanical (MM) and quantum mechanical (QM) data. Three types of performance were assessed: (1) geometrical optimizations and binding energy calculations for 27 halogen-containing molecules complexed with various Lewis bases (Two of the tested methods, AM1 and RM1, gave results that agree with the QM data.); (2) charge distribution calculations for halobenzene molecules, determined by calculating the solvation free energies of the molecules relative to benzene in explicit and implicit generalized Born (GB) solvents (None of the methods gave results that agree with the experimental data.); and (3) appropriateness of the semiempirical methods in the hybrid quantum-mechanical/molecular-mechanical (QM/MM) scheme, investigated by studying the molecular inhibition of CK2 protein by eight halobenzimidazole and -benzotriazole derivatives using hybrid QM/MM molecular-dynamics (MD) simulations with the inhibitor described at the QM level by the AM1 method and the rest of the system described at the MM level. The pure MM approach with inclusion of an extra point of positive charge on the halogen atom approach gave better results than the hybrid QM/MM approach involving the AM1 method. Also, in comparison with the pure MM-GBSA (generalized Born surface area) binding energies and experimental data, the calculated QM/MM-GBSA binding energies of the inhibitors were improved by replacing the G(GB,QM/MM) solvation term with the corresponding G(GB,MM) term.

Further development of LLNA:DAE method as stand-alone skin-sensitization testing method and applied for evaluation of relative skin-sensitizing potency between chemicals.

Science.gov (United States)

Yamashita, Kunihiko; Shinoda, Shinsuke; Hagiwara, Saori; Itagaki, Hiroshi

2015-04-01

To date, there has been no well-established local lymph node assay (LLNA) that includes an elicitation phase. Therefore, we developed a modified local lymph node assay with an elicitation phase (LLNA:DAE) to discriminate true skin sensitizers from chemicals that gave borderline positive results and previously reported this assay. To develop the LLNA:DAE method as a useful stand-alone testing method, we investigated the complete procedure for the LLNA:DAE method using hexyl cinnamic aldehyde (HCA), isoeugenol, and 2,4-dinitrochlorobenzene (DNCB) as test compounds. We defined the LLNA:DAE procedure as follows: in the dose-finding test, four concentrations of chemical applied to dorsum of the right ear on days 1, 2, and 3 and dorsum of both ears on day 10. Ear thickness and skin irritation score were measured on days 1, 3, 5, 10, and 12. Local lymph nodes were excised and weighed on day 12. The test dose for the primary LLNA:DAE study was selected as the dose that gave the highest left ear lymph node weight in the dose-finding study, or the lowest dose that produced a left ear lymph node of over 4 mg. This procedure was validated using nine different chemicals. Furthermore, qualitative relationship was observed between the degree of elicitation response in the left ear lymph node and the skin sensitizing potency of 32 chemicals tested in this study and the previous study. These results indicated that LLNA:DAE method was as first LLNA method that was able to evaluate the skin sensitizing potential and potency in elicitation response.

The surgical significance of the atrial branches of the coronary arteries.

Science.gov (United States)

Busquet, J; Fontan, F; Anderson, R H; Ho, S Y; Davies, M J

1984-08-01

The great number of open heart operations now performed via the right atrium, makes knowledge of the arrangement of the atrial arteries, particularly the sinus node artery, every important for the surgeon. Although studied by anatomists, little attention has been paid to the surgical significance of these arteries. We have therefore examined the distribution of the right atrial arteries and the course of the sinus node artery in 50 normal adult hearts by classic dissection following, in 30 cases, postmortem angiographic studies. Two major arteries of the right atrium were found to be nearly constant. The anterior artery was present in 96% of the cases and supplied the sinus node artery in 32 cases. Of most surgical significance was the lateral artery found in 90% of the cases. This lateral artery was the principal artery to the free atrial wall and in one case gave rise to the sinus node artery. The well-established preponderance of origin of the sinus node artery from the right coronary system (66%) as opposed to the left (30%) was confirmed. Infrequently, a double supply (4%) was seen. Variability was found in the course of the nodal artery relative to the cavoatrial junction - precaval (58%), retrocaval (36%) or encircling (6%).

Website-based PNG image steganography using the modified Vigenere Cipher, least significant bit, and dictionary based compression methods

Science.gov (United States)

Rojali, Salman, Afan Galih; George

2017-08-01

Along with the development of information technology in meeting the needs, various adverse actions and difficult to avoid are emerging. One of such action is data theft. Therefore, this study will discuss about cryptography and steganography that aims to overcome these problems. This study will use the Modification Vigenere Cipher, Least Significant Bit and Dictionary Based Compression methods. To determine the performance of study, Peak Signal to Noise Ratio (PSNR) method is used to measure objectively and Mean Opinion Score (MOS) method is used to measure subjectively, also, the performance of this study will be compared to other method such as Spread Spectrum and Pixel Value differencing. After comparing, it can be concluded that this study can provide better performance when compared to other methods (Spread Spectrum and Pixel Value Differencing) and has a range of MSE values (0.0191622-0.05275) and PSNR (60.909 to 65.306) with a hidden file size of 18 kb and has a MOS value range (4.214 to 4.722) or image quality that is approaching very good.

Simplified LCA and matrix methods in identifying the environmental aspects of a product system.

Science.gov (United States)

Hur, Tak; Lee, Jiyong; Ryu, Jiyeon; Kwon, Eunsun

2005-05-01

In order to effectively integrate environmental attributes into the product design and development processes, it is crucial to identify the significant environmental aspects related to a product system within a relatively short period of time. In this study, the usefulness of life cycle assessment (LCA) and a matrix method as tools for identifying the key environmental issues of a product system were examined. For this, a simplified LCA (SLCA) method that can be applied to Electrical and Electronic Equipment (EEE) was developed to efficiently identify their significant environmental aspects for eco-design, since a full scale LCA study is usually very detailed, expensive and time-consuming. The environmentally responsible product assessment (ERPA) method, which is one of the matrix methods, was also analyzed. Then, the usefulness of each method in eco-design processes was evaluated and compared using the case studies of the cellular phone and vacuum cleaner systems. It was found that the SLCA and the ERPA methods provided different information but they complemented each other to some extent. The SLCA method generated more information on the inherent environmental characteristics of a product system so that it might be useful for new design/eco-innovation when developing a completely new product or method where environmental considerations play a major role from the beginning. On the other hand, the ERPA method gave more information on the potential for improving a product so that it could be effectively used in eco-redesign which intends to alleviate environmental impacts of an existing product or process.

Significance of uniaxial and hydrostatic pressure studies on ancient oceanic rocks in tectonics

Digital Repository Service at National Institute of Oceanography (India)

Sarma, K.V.L.N.S.; Ramana, Y.V.

showed the lowest value of compressive strength (45 MPa) and pyroxenite gave the highest value (269 MPa), while meta volcanics exhibited narrow limits of 58 to 245 MPa. Standard correlations were obtained for compressive strength to G/P ratio...

Investigation of dispersion-relation-preserving scheme and spectral analysis methods for acoustic waves

Science.gov (United States)

Vanel, Florence O.; Baysal, Oktay

1995-01-01

Important characteristics of the aeroacoustic wave propagation are mostly encoded in their dispersion relations. Hence, a computational aeroacoustic (CAA) algorithm, which reasonably preserves these relations, was investigated. It was derived using an optimization procedure to ensure, that the numerical derivatives preserved the wave number and angular frequency of the differential terms in the linearized, 2-D Euler equations. Then, simulations were performed to validate the scheme and a compatible set of discretized boundary conditions. The computational results were found to agree favorably with the exact solutions. The boundary conditions were transparent to the outgoing waves, except when the disturbance source was close to a boundary. The time-domain data generated by such CAA solutions were often intractable until their spectra was analyzed. Therefore, the relative merits of three different methods were included in the study. For simple, periodic waves, the periodogram method produced better estimates of the steep-sloped spectra than the Blackman-Tukey method. Also, for this problem, the Hanning window was more effective when used with the weighted-overlapped-segment-averaging and Blackman-Tukey methods gave better results than the periodogram method. Finally, it was demonstrated that the representation of time domain-data was significantly dependent on the particular spectral analysis method employed.

Anatomical variations in dorsal metatarsal arteries with surgical significance: A cadaveric study

Directory of Open Access Journals (Sweden)

Preeti Shivshankar Awari

2017-01-01

Full Text Available Introduction: Based on angiosome concept to revascularize a particular artery, the microvascular and reconstructive surgeons must know the anatomy and variations in the arteries in that specific region of the body to achieve better results. Nowadays, dorsal metatarsal artery (DMTA perforator flaps and toe grafts are becoming popular which also demand adequate information about normal anatomy and variants in these arteries for fruitful results. Materials and Methods: The authors studied normal anatomy and variations in the origin of DMTAs in 50 lower extremities of 25 embalmed cadavers. Results: The authors found many variations as the absence of DMTAs, origin of the DMTA from the deep plantar arch. The places wherever the arcuate artery was absent the lateral tarsal artery gave rise to dorsal metatarsal arteries. Conclusion: Being familiar with the incidence of anatomical variations in the origin of the DMTAs can increase vigilance in vascular and reconstructive surgeries leading to better prognosis. surgeries leading to better prognosis.

Applying the chronicle workshop as a method for evaluating participatory interventions

DEFF Research Database (Denmark)

Poulsen, Signe; Ipsen, Christine; Gish, Liv

2015-01-01

Despite the growing interest for process evaluation in participatory interventions, studies examining specific methods for process evaluation are lacking. In this paper, we propose a new method for process evaluation – the chronicle workshop. The chronicle workshop has not previously been used...... productivity and well-being. In all cases, we saw that the chronicle workshop gave valuable information about the intervention process and that it initiated a joint reflection among participants from different departments. The chronicle workshop makes it possible to better understand the results...

Analysis of Protein by Spectrophotometric and Computer Colour Based Intensity Method from Stem of Pea (Pisum sativum at Different Stages

Directory of Open Access Journals (Sweden)

Afsheen Mushtaque Shah

2010-12-01

Full Text Available In this study proteins were analyzed from pea plants at three different growth stages of stem by spectrophotometric i.e Lowry and Bradford quantitative methods and computer colour intensity based method. Though Spectrophotometric methods are regarded as classical methods, we report an alternate computer based method which gave comparable results. Computer software was developed the for protein analysis which is easier, time and money saving method as compared to the classical methods.

Labile soil phosphorus as influenced by methods of applying radioactive phosphorus

International Nuclear Information System (INIS)

Selvaratnam, V.V.; Andersen, A.J.; Thomsen, J.D.; Gissel-Nielsen, G.

1980-03-01

The influence of different methods of applying radioactive phosphorus on the E- and L-values was studied in four foil types using barley, buckwheat, and rye grass for the L-value determination. The four soils differed greatly in their E- and L-values. The experiment was carried out both with and without carrier-P. The presence of carrier-P had no influence on the E-values, while carrier-P in some cases gave a lower L-value. Both E- and L-values dependent on the method of application. When the 32 P was applied on a small soil or sand sample and dried before mixing with the total amount of soil, the E-values were higher than at direct application most likely because of a stronger fixation to the soil/sand particles. This was not the case for the L-values that are based on a much longer equilibrium time. On the contrary, the direct application of the 32 p-solution to the whole amount of soil gave higher L-values of a non-homogeneous distribution of the 32 p in the soil. (author)

IAEA intercomparison of methods for processing Ge(Li) gamma-ray spectra: a preliminary report

International Nuclear Information System (INIS)

Parr, R.M.; Houtermans, H.; Schaerf, K.

1979-01-01

Nine spectra were provided, each covering an energy range of about 1 MeV and, with one exception, containing only well-separated single peaks; the exception was a spectrum containing double peaks. The intercomparison enables the user to test the ability of his methods: (1) to detect small peaks near the limit of detectability, (2) to determine the positions and areas of more easily detectable peaks, and (3) to determine the positions and areas of overlapping double peaks. A total of 212 sets of results was finally received for evaluation from 163 laboratories in 34 member states of the IAEA. For all the different types of tests involved, the methods reported covered a wide range of performance. Classification of these methods did not reveal any group offering a significantly restricted range of performance, though some groups of methods did appear, in the best hands, to be capable of producing better results than others: (1) for peak detection: visual methods and the use of the second derivative, (2) for peak-position (single peaks) determination: the fitting of a parabola or modified Gaussian function, and (3) for peak-area (single peaks) and peak-position and area (double peaks) determination: the fitting of a modified Gaussian function. Many methods reported gave either no estimates or poor estimates of error. With the exception of manual methods, the operating environment (e.g., large or small computer) did not appear to have any significant influence on the results. A comparison of four commonly used computer programs showed that the best results were obtained by SAMPO

Learning Using Dynamic and Static Visualizations: Students' Comprehension, Prior Knowledge and Conceptual Status of a Biotechnological Method

Science.gov (United States)

Yarden, Hagit; Yarden, Anat

2010-05-01

The importance of biotechnology education at the high-school level has been recognized in a number of international curriculum frameworks around the world. One of the most problematic issues in learning biotechnology has been found to be the biotechnological methods involved. Here, we examine the unique contribution of an animation of the polymerase chain reaction (PCR) in promoting conceptual learning of the biotechnological method among 12th-grade biology majors. All of the students learned about the PCR using still images ( n = 83) or the animation ( n = 90). A significant advantage to the animation treatment was identified following learning. Students’ prior content knowledge was found to be an important factor for students who learned PCR using still images, serving as an obstacle to learning the PCR method in the case of low prior knowledge. Through analysing students’ discourse, using the framework of the conceptual status analysis, we found that students who learned about PCR using still images faced difficulties in understanding some mechanistic aspects of the method. On the other hand, using the animation gave the students an advantage in understanding those aspects.

Significance of steel electrical resistance method in the evaluation of reinforcement corrosion in cementitious systems

Directory of Open Access Journals (Sweden)

Krajci, L.

2004-06-01

Full Text Available The suitable detection system of steel reinforcement corrosion in concrete structures contributes to the reduction of their maintenance costs. Method of steel electrical resistance represents non-destructive monitoring of steel in cementitious systems. Specially prepared and arranged test specimen of steel as a corrosion sensor is embedded in mortar specimen. Verification tests of this method based on chloride corrosion of steel in mortars as well as its visual inspection are introduced. Significance of steel electrical resistance method lies in the expression of steel corrosion by these quantitative parameters: reduction of cross-section of steel, thickness of corroded layer and loss of weight of steel material. This method is an integral method that allows the indirect determination of mentioned corrosion characteristics. The comparison of verified method with gravimetric evaluation of steel corrosion gives a good correspondence. Test results on mortars with calcium chloride dosages between 0.5% and 4.0% by weight of cement prove high sensitiveness and reliability of steel electrical resistance method.

La utilización de un sistema de detección de la corrosión de las armaduras en estructuras de hormigón puede contribuir a la reducción de sus costes de mantenimiento. El método de la resistencia eléctrica del acero consiste en la monitorización no-destructiva realizada sobre el acero en sistemas cementantes. Dentro de la muestra de mortero se coloca el sistema de detección, especialmente preparado y fijado, actuando como un sensor de la corrosión. En este trabajo se presentan ensayos de verificación de este método, junto con inspecciones visuales, en morteros sometidos a corrosión de armaduras por efecto de los cloruros. La efectividad de este método de la resistencia eléctrica del acero se expresa, en la corrosión de armaduras, de acuerdo a los siguientes parámetros cuantitativos: reducción de la sección transversal del

Measurement of the second moment in NMR using instationary methods

International Nuclear Information System (INIS)

Fenzke, D.; Rinck, W.; Schneider, H.

1973-01-01

Different instationary methods for determination of the second moment in NMR are tested. Measurements were carried out with a noncommercial solid-state pulse spectrometer with a fast analog transient memory (aquisition time >0.5 μs), data processing with a ''DIDAC 800'' spectrum accumulator and a ''NICOLET-1080'' computer. For processing of signals three methods are discussed: the numerical differentiation, the least square method and an application of the sampling theorem. We determined the second moment observing the ''Free Induction Decay'', ''Solid Echo'', ''Magic Echo'' and a special group of many pulse pairs. ''Magic Echo'' and data processing with the least square method gave the best result, because only by this method the influence of apparatus dead time can be completely eliminated. (author)

Comparison of wet-chemical methods for determination of lipid hydroperoxides

DEFF Research Database (Denmark)

Nielsen, Nina Skall; Timm Heinrich, Maike; Jacobsen, Charlotte

2003-01-01

Five methods for determination of lipid hydroperoxides were evaluated, including two iodometric procedures involving a titration and a spectrophotometric micro method, and three other spectrophotometric methods namely the ferro, International Dairy Federation (IDF) and FOX2 (ferrous oxidation...... in xylenol orange). Peroxide values determined in a range of food products by these five methods gave different results. The ferro method required large amounts of solvent (50 mL/sample); the FOX2 method had a low range (0.005-0.04 mumol hydroperoxide); the end point detection of the titration method...... was subjective and required a large amount of sample (1 g); and the micro method was sensitive to interruptions during execution. Therefore, only the modified IDF method was chosen for further testing and validation. Stability tests of the standard curve showed a variation coefficient of 4% and within runs...

Comparison of three methods for detection of herbal food supplement irradiation

DEFF Research Database (Denmark)

Leth, Torben; Hansen, Hanne; Boisen, Flemming

2006-01-01

A survey for irradiation of 106 herbal food supplements was carried out in Denmark in 2003. The results from three methods, two screening methods and a specific method, were compared: Direct epifluorescent filter technique/aerobic plate count (DEFT/APC), photostimulated luminescence (PSL) and the......A survey for irradiation of 106 herbal food supplements was carried out in Denmark in 2003. The results from three methods, two screening methods and a specific method, were compared: Direct epifluorescent filter technique/aerobic plate count (DEFT/APC), photostimulated luminescence (PSL......) and thermoluminescence (TL) standardised by Comite Europeen de Normalisation (CEN). Forty samples screened positive with the DEFT/APC method. However, the TL method could only confirm irradiation of 15 samples, 11 samples wholly irradiated and 4 samples with a minor irradiated ingredient. Thus, the DEFT/APC method gave...

[Hierarchy structuring for mammography technique by interpretive structural modeling method].

Science.gov (United States)

Kudo, Nozomi; Kurowarabi, Kunio; Terashita, Takayoshi; Nishimoto, Naoki; Ogasawara, Katsuhiko

2009-10-20

Participation in screening mammography is currently desired in Japan because of the increase in breast cancer morbidity. However, the pain and discomfort of mammography is recognized as a significant deterrent for women considering this examination. Thus quick procedures, sufficient experience, and advanced skills are required for radiologic technologists. The aim of this study was to make the point of imaging techniques explicit and to help understand the complicated procedure. We interviewed 3 technologists who were highly skilled in mammography, and 14 factors were retrieved by using brainstorming and the KJ method. We then applied Interpretive Structural Modeling (ISM) to the factors and developed a hierarchical concept structure. The result showed a six-layer hierarchy whose top node was explanation of the entire procedure on mammography. Male technologists were related to as a negative factor. Factors concerned with explanation were at the upper node. We gave attention to X-ray techniques and considerations. The findings will help beginners improve their skills.

Performance comparison of machine learning methods for prognosis of hormone receptor status in breast cancer tissue samples.

Science.gov (United States)

Kalinli, Adem; Sarikoc, Fatih; Akgun, Hulya; Ozturk, Figen

2013-06-01

We examined the classification and prognostic scoring performances of several computer methods on different feature sets to obtain objective and reproducible analysis of estrogen receptor status in breast cancer tissue samples. Radial basis function network, k-nearest neighborhood search, support vector machines, naive bayes, functional trees, and k-means clustering algorithm were applied to the test datasets. Several features were employed and the classification accuracies of each method for these features were examined. The assessment results of the methods on test images were also experimentally compared with those of two experts. According to the results of our experimental work, a combination of functional trees and the naive bayes classifier gave the best prognostic scores indicating very good kappa agreement values (κ=0.899 and κ=0.949, p<0.001) with the experts. This combination also gave the best dichotomization rate (96.3%) for assessment of estrogen receptor status. Wavelet color features provided better classification accuracy than Laws texture energy and co-occurrence matrix features. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Evaluation of DNA extraction methods for the detection of Cytomegalovirus in dried blood spots

Science.gov (United States)

Koontz, D.; Baecher, K.; Amin, M.; Nikolova, S.; Gallagher, M.; Dollard, S.

2015-01-01

Background Dried blood spots (DBS) are collected universally from newborns and may be valuable for the diagnosis of congenital Cytomegalovirus (CMV) infection. The reported analytical sensitivity for DBS testing compared to urine or saliva varies greatly across CMV studies. The purpose of this study was to directly compare the performance of various DNA extraction methods for identification of CMV in DBS including those used most often in CMV studies. Study design Whatman® Grade 903 filter paper cards were spotted with blood samples from 25 organ transplant recipients who had confirmed CMV viremia. Six DNA extraction methods were compared for relative yield of viral and cellular DNA: 2 manual solution-based methods (Gentra Puregene, thermal shock), 2 manual silica column-based methods (QIAamp DNA Mini, QIAamp DNA Investigator), and 2 automated methods (M48 MagAttract Mini, QIAcube Investigator). DBS extractions were performed in triplicate followed by real-time quantitative PCR (qPCR). Results For extraction of both viral and cellular DNA, two methods (QIAamp DNA Investigator and thermal shock) consistently gave the highest yields, and two methods (M48 MagAttract Mini and QIAamp DNA Mini) consistently gave the lowest yields. There was an average 3-fold difference in DNA yield between the highest and lowest yield methods. Conclusion The choice of DNA extraction method is a major factor in the ability to detect low levels of CMV in DBS and can largely account for the wide range of DBS sensitivities reported in studies to date. PMID:25866346

TESTING METHODS FOR MECHANICALLY IMPROVED SOILS: RELIABILITY AND VALIDITY

Directory of Open Access Journals (Sweden)

Ana Petkovšek

2017-10-01

Full Text Available A possibility of in-situ mechanical improvement for reducing the liquefaction potential of silty sands was investigated by using three different techniques: Vibratory Roller Compaction, Rapid Impact Compaction (RIC and Soil Mixing. Material properties at all test sites were investigated before and after improvement with the laboratory and the in situ tests (CPT, SDMT, DPSH B, static and dynamic load plate test, geohydraulic tests. Correlation between the results obtained by different test methods gave inconclusive answers.

Impact significance determination-Pushing the boundaries

International Nuclear Information System (INIS)

Lawrence, David P.

2007-01-01

Impact significance determination practice tends to be highly variable. Too often insufficient consideration is given to good practice insights. Also, impact significance determinations are frequently narrowly defined addressing, for example, only individual, negative impacts, focusing on bio-physical impacts, and not seeking to integrate either the Precautionary Principle or sustainability. This article seeks to extend the boundaries of impact significance determination practice by providing an overview of good general impact significance practices, together with stakeholder roles and potential methods for addressing significance determination challenges. Relevant thresholds, criteria, contextual considerations and support methods are also highlighted. The analysis is then extended to address how impact significance determination practices change for positive as compared with negative impacts, for cumulative as compared with individual impacts, for socio-economic as compared with bio-physical impacts, when the Precautionary Principle is integrated into the process, and when sustainability contributions drive the EIA process and related impact significance determinations. These refinements can assist EIA practitioners in ensuring that the scope and nature of impact significance determinations reflect the broadened scope of emerging EIA requirements and practices. Suggestions are included for further refining and testing of the proposed changes to impact significance determination practice

Superconducting property measuring system by magnetization method

International Nuclear Information System (INIS)

Ikisawa, K.; Mori, T.; Takasu, N.

1988-01-01

Superconducting property measuring system (CMS-370B) for high temperature oxide superconductor has been developed. This system adopts magnetization measurement. The superconducting properties are able to be measured automatically and continuously changing the temperature and external magnetic field. The critical current density as a function of temperature and magnetic field of high temperature superconductor YBa 2 Cu 3 O 7-y (YBCO) has been measured. This paper reports how it was confirmed that this system having the high performance and the accuracy gave the significant contribution to the superconducting material development

Analytical methods of heat transfer compared with numerical methods as related to nuclear waste repositories

International Nuclear Information System (INIS)

Estrada-Gasca, C.A.

1986-01-01

Analytical methods were applied to the prediction of the far-field thermal impact of a nuclear waste repository. Specifically, the transformation of coordinates and the Kirchhoff transformation were used to solve one-dimensional nonlinear heat conduction problems. Calculations for the HLW and TRU nuclear waste with initial areal thermal loadings of 12 kW/acre and 0.7 kW/acre, respectively, are carried out for various models. Also, finite difference and finite element methods are applied. The last method is used to solve two-dimensional linear and nonlinear heat conduction problems. Results of the analysis are temperature distributions and temperature histories. Explicit analytical expressions of the maximum temperature rise as a function of the system parameters are presented. The theoretical approaches predict maximum temperature increases in the overburden with an error of 10%. When the finite solid one-dimensional NWR thermal problem is solved with generic salt and HLW thermal load as parameters, the maximum temperature rises predicted by the finite difference and finite element methods had maximum errors of 2.6 and 6.7%, respectively. In all the other cases the finite difference method also gave a smaller error than the finite element method

Carrageenan :the difference between PNG and KCL gel precipitation method as Lactobacillus acidophilus encapsulation material

Science.gov (United States)

Setijawati, D.; Nursyam, H.; Salis, H.

2018-04-01

The study on the effects of using of materials and methods in the preparation of the microcapsules Lactobacillus acidophilus towards the viability has been done. The research method used is experimental laboratory design. Variable research was kind of material (A) as the first factor with sub factor (A1 = Eucheuma cottonii) (A2 = Eucheuma spinosum) (A3 = mixture of Eucheuma cottonii and Eucheuma spinosum 1:1 ratio), while the second factor is a method of extraction to produce caragenan (B) with sub factor (B1 = Philipine Natural Grade modification) (B2 = KCl gel Press Precipitation). Analysis of different influences uses Analysis Of Varians followed by Fisher’s test. Analysis of data uses Mini tab 16. The results shows that the kind of extraction factors and methods gave significantly different effects on the viability of Lactobacillus acidophilus. The highest mean of Viablity obtained in the treatment of materials with a mixture of Eucheuma cottonii and Eucheuma spinosum and used KCl Gel Press method is equal to 7.14 log (CFU / mL). It is ssuggested using of kappa-iota carrageenanmixture asencapsulation material with KCl Gel Press method on Lactobacillus acidophilus microencapsulation process because it treatment gavethe highest average of Lactobacillus acidophilus viability.

Statistical significance of cis-regulatory modules

Directory of Open Access Journals (Sweden)

Smith Andrew D

2007-01-01

Full Text Available Abstract Background It is becoming increasingly important for researchers to be able to scan through large genomic regions for transcription factor binding sites or clusters of binding sites forming cis-regulatory modules. Correspondingly, there has been a push to develop algorithms for the rapid detection and assessment of cis-regulatory modules. While various algorithms for this purpose have been introduced, most are not well suited for rapid, genome scale scanning. Results We introduce methods designed for the detection and statistical evaluation of cis-regulatory modules, modeled as either clusters of individual binding sites or as combinations of sites with constrained organization. In order to determine the statistical significance of module sites, we first need a method to determine the statistical significance of single transcription factor binding site matches. We introduce a straightforward method of estimating the statistical significance of single site matches using a database of known promoters to produce data structures that can be used to estimate p-values for binding site matches. We next introduce a technique to calculate the statistical significance of the arrangement of binding sites within a module using a max-gap model. If the module scanned for has defined organizational parameters, the probability of the module is corrected to account for organizational constraints. The statistical significance of single site matches and the architecture of sites within the module can be combined to provide an overall estimation of statistical significance of cis-regulatory module sites. Conclusion The methods introduced in this paper allow for the detection and statistical evaluation of single transcription factor binding sites and cis-regulatory modules. The features described are implemented in the Search Tool for Occurrences of Regulatory Motifs (STORM and MODSTORM software.

Extractive Spectrophotometric Methods for the Determination of Etoricoxib in Tablets

Directory of Open Access Journals (Sweden)

Kamal Shah

2009-01-01

Full Text Available Two simple, rapid, sensitive, precise and economic spectrophotometric methods have been developed for the estimation of etoricoxib in tablet formulation. During the course of study, it was observed that acidic solution of the drug formed colored ion-association complexes with Bromocresol Green (BCG and Bromocresol Purple (BCP which were soluble in chloroform. This property of the drug was followed for the development of colorimetric methods for analysis of drug. The complex of etoricoxib with BCG and BCP showed λmax at 416 nm and 408 nm respectively. These methods were validated statistically. Recovery studies gave satisfactory results indicating that none of common additives and excipients interfere the assay method. The proposed methods are found to be simple, accurate and reproducible that was successfully applied for the analysis of tablet formulation.

Preservation methods for isolates of ascochyta blight fungi

Directory of Open Access Journals (Sweden)

Joanna Marcinkowska

2014-08-01

Full Text Available Isolates of ascochyta blight fungi, two of Ascochyta pisi, four of Mycosphaerella pinodes and four of Phoma pinodella were stored: A - on slants under mineral oil, B - on CN's medium agar disks, and as conidial suspension: C - in glycerine, D · in water. Viability and pathogenicity of recovered cultures after each consecutive year were assesed from 1991 to 1999. The compared parameters were first of all strongly influenced by the preservation method, but fungus species and number of years had a minor importance. The best for longer storage was method "A" because after 9 years the isolates were viable, highly pathogenic, and cultures recovered from them were clean. Thc method "C'' is good for short keeping (2-3 years, as conidia in vials need only small space and gave clean cultures.

Rapid method for measuring protease activity in milk using radiolabeled casein

International Nuclear Information System (INIS)

Christen, G.L.

1987-01-01

A rapid means to detect the presence of protease activity in raw milk could be useful in predicting keeping ability of products made from that milk. A 30-min assay has been developed and compared with three other methods of detecting protease. Casein, [methyl- 14 C]-methylated-alpha was purchased from a radioisotope supplier. Concentrations of substrate from 2 to 20 nCi gave counts per minute, which increased linearly when counted with the Charm analyzer. There was not a significant difference in counting times of 10, 20, or 30 min. A mixture of sodium acetate and acetic acid precipitated nonhydrolyzed substrate with an efficiency of 97%. Comparison of the [ 14 C] casein assay, a casein fluorescein isothiocyanate assay, trinitrobenzenesulfonic acid procedure, and the Hull procedure using protease from psychrotrophic bacteria revealed that the [ 14 C] casein and casein fluorescein isothiocyanate methods were roughly equivalent and that the radiometric procedure was 10 times more sensitive than the trinitrobenzenesulfonic acid assay. The radiometric procedure was approximately 10(4) times more sensitive than the Hull procedure. The [ 14 C] casein and casein fluorescein isothiocyanate methods were similar in time required, about 30 min, while the trinitrobenzenesulfonic acid assay and Hull method required about 1 h plus reagent preparation time. The [ 14 C] casein procedure was most expensive per test; the other three were cheaper and similar to each other in cost

Dosimetry using radiosensitive gels in radiotherapy: significance and methods

International Nuclear Information System (INIS)

Gibon, D.; Bourel, P.; Castelain, B.; Marchandise, X.; Rousseau, J.

2001-01-01

The goal of conformal radiotherapy is to concentrate the dose in a well-defined volume by avoiding the neighbouring healthy structures. This technique requires powerful treatment planning software and a rigorous control of estimated dosimetry. The usual dosimetric tools are not adapted to visualize and validate complex 3D treatment. Dosimetry by radiosensitive gel permits visualization and measurement of the three-dimensional dose distribution. The objective of this work is to report on current work in this field and, based on our results and our experience, to draw prospects for an optimal use of this technique. Further developments will relate to the realization of new radiosensitive gels satisfying, as well as possible, cost requirements, easy realization and use, magnetic resonance imagery (MRI) sensitivity, tissue equivalence, and stability. Other developments focus on scanning methods, especially in MRI to measure T1 and T2. (author)

Untargeted metabolomic profiling plasma samples of patients with lung cancer for searching significant metabolites by HPLC-MS method

Science.gov (United States)

Dementeva, N.; Ivanova, K.; Kokova, D.; Kurzina, I.; Ponomaryova, A.; Kzhyshkowska, J.

2017-09-01

Lung cancer is one of the most common types of cancer leading to death. Consequently, the search and the identification of the metabolites associated with the risk of developing cancer are very valuable. For the purpose, untargeted metabolic profiling of the plasma samples collected from the patients with lung cancer (n = 100) and the control group (n = 100) was conducted. After sample preparation, the plasma samples were analyzed using LC-MS method. Biostatistics methods were applied to pre-process the data for elicitation of dominating metabolites which responded to the difference between the case and the control groups. At least seven significant metabolites were evaluated and annotated. The most part of identified metabolites are connected with lipid metabolism and their combination could be useful for follow-up studies of lung cancer pathogenesis.

Foods The Indians Gave Us. Coloring Book.

Science.gov (United States)

Hail, Raven

This children's coloring book devotes a page to each of twenty of the most familiar American Indian plant foods: avocado, green beans, black walnuts, cocoa, corn, peanuts, pecans, chile peppers, pineapples, popcorn, potatoes, pumpkins, squash, strawberries, sugar maple, sunflowers, sweet potatoes, tapioca, tomatoes, and vanilla. Illustrating each…

Purification of crude glycerol from transesterification reaction of palm oil using direct method and multistep method

Science.gov (United States)

Nasir, N. F.; Mirus, M. F.; Ismail, M.

2017-09-01

Crude glycerol which produced from transesterification reaction has limited usage if it does not undergo purification process. It also contains excess methanol, catalyst and soap. Conventionally, purification method of the crude glycerol involves high cost and complex processes. This study aimed to determine the effects of using different purification methods which are direct method (comprises of ion exchange and methanol removal steps) and multistep method (comprises of neutralization, filtration, ion exchange and methanol removal steps). Two crude glycerol samples were investigated; the self-produced sample through the transesterification process of palm oil and the sample obtained from biodiesel plant. Samples were analysed using Fourier Transform Infrared Spectroscopy, Gas Chromatography and High Performance Liquid Chromatography. The results of this study for both samples after purification have showed that the pure glycerol was successfully produced and fatty acid salts were eliminated. Also, the results indicated the absence of methanol in both samples after purification process. In short, the combination of 4 purification steps has contributed to a higher quality of glycerol. Multistep purification method gave a better result compared to the direct method as neutralization and filtration steps helped in removing most excess salt, fatty acid and catalyst.

The Guidelines for Modelling the Preloading Bolts in the Structural Connection Using Finite Element Methods

OpenAIRE

Paulina Krolo; Davor Grandić; Mladen Bulić

2016-01-01

The aim of this paper is the development of the two different numerical techniques for the preloading of bolts by the finite element method using the software Abaqus Standard. Furthermore, this paper gave detailed guidelines for modelling contact, method for solving the numerical error problems such as numerical singularity error and negative eigenvalues due to rigid body motion or the problem of the extensive elongation of bolts after pretension which is occurring during the analysis. The be...

Gastric ulcer localization by direct in vivo labeling of sucralfate: work in progress

Energy Technology Data Exchange (ETDEWEB)

Pera, A.; Seevers, R.H.; Meyer, K.; Hall, C.; Bekerman, C.; Anderson, T.M.; Katzen, H.; Laakso, L.; Pinsky, S.M.

1985-09-01

The authors developed and evaluated a new procedure for imaging gastric ulcer disease with technetium 99m - labeled sucralfate. The new method employs direct in vivo labeling of sucralfate instead of in vitro labeling using human serum albumin, as previously reported in the literature. In 26 studies using humans with sucralfate labeled directly in vivo, 15 gave true-negative results. Of 14 studies using humans with in vitro labeled sucralfate, three gave true-negative results, three gave true-positive results, and the results of eight were either false-negative or could not be interpreted because of high levels of activity remaining in the stomach. They suggest that the direct in vivo labeling method significantly improves the sucralfate gastric ulcer imaging technique.

Gastric ulcer localization by direct in vivo labeling of sucralfate: work in progress

International Nuclear Information System (INIS)

Pera, A.; Seevers, R.H.; Meyer, K.; Hall, C.; Bekerman, C.; Anderson, T.M.; Katzen, H.; Laakso, L.; Pinsky, S.M.

1985-01-01

The authors developed and evaluated a new procedure for imaging gastric ulcer disease with technetium 99m - labeled sucralfate. The new method employs direct in vivo labeling of sucralfate instead of in vitro labeling using human serum albumin, as previously reported in the literature. In 26 studies using humans with sucralfate labeled directly in vivo, 15 gave true-negative results. Of 14 studies using humans with in vitro labeled sucralfate, three gave true-negative results, three gave true-positive results, and the results of eight were either false-negative or could not be interpreted because of high levels of activity remaining in the stomach. They suggest that the direct in vivo labeling method significantly improves the sucralfate gastric ulcer imaging technique

Cytogenetic chromosomal aberration dosimetry method after radiation accidents and prognostic significance of stereotypically appearing chromosomal aberrations after radiation exposure

International Nuclear Information System (INIS)

Bloennigen, K.A.

1973-01-01

The paper reports on a radiation accident involving an Iridium-192 rod of an activity of 7.8 Ci and a size of 2 x 2 x 2 mm 3 . The radiation source had remained in direct contact with the left hip and elbow of the examined person for a period of 45 minutes. On the points that had been directly exposed, physical values of 5,000 rad and 10,000 rad were measured while the whole-body dose was 100-200 rad and the gonad dose 300-400 rad. These values were confirmed by observations of the clinical course and haematological and andrological examinations. Chromosome analysis of lymphocytes produced values between 100 and 125 and thus a significant agreement with the values determined by physical methods. The findings suggest that the relatively simple and fast method of cytogenetic dosimetry provides a useful complementary method to physical dosimetry. (orig./AK) [de

Assessing the stability of free-energy perturbation calculations by performing variations in the method

Science.gov (United States)

Manzoni, Francesco; Ryde, Ulf

2018-03-01

We have calculated relative binding affinities for eight tetrafluorophenyl-triazole-thiogalactoside inhibitors of galectin-3 with the alchemical free-energy perturbation approach. We obtain a mean absolute deviation from experimental estimates of only 2-3 kJ/mol and a correlation coefficient (R 2) of 0.5-0.8 for seven relative affinities spanning a range of up to 11 kJ/mol. We also studied the effect of using different methods to calculate the charges of the inhibitor and different sizes of the perturbed group (the atoms that are described by soft-core potentials and are allowed to have differing coordinates). However, the various approaches gave rather similar results and it is not possible to point out one approach as consistently and significantly better than the others. Instead, we suggest that such small and reasonable variations in the computational method can be used to check how stable the calculated results are and to obtain a more accurate estimate of the uncertainty than if performing only one calculation with a single computational setup.

An outline of the systematic-dialectical method: scientific and political significance

NARCIS (Netherlands)

Reuten, G.; Moseley, F.; Smith, T.

2014-01-01

The method of systematic-dialectics (SD) is reconstructed with a focus on what institutions and processes are necessary - rather than contingent - for the capitalist system. This allows for the detection of strengths and weaknesses in the actual structure of the system. Weaknesses should be

A SWIFT Method for Handing Off Obstetrical Patients on the Labor Floor.

Science.gov (United States)

Sheen, Jean-Ju; Reimers, Laura; Govindappagari, Shravya; Ngai, Ivan M; Garretto, Diana; Donepudi, Roopali; Tropper, Pamela; Goffman, Dena; Dayal, Ashlesha K; Bernstein, Peter S

2017-07-06

The aim of this study was to improve patient handoffs on the labor floor. A prospective cohort study of obstetrics residents at Montefiore Medical Center was performed between 2012 and 2014. Labor-floor handoffs were recorded before and after didactic sessions as well as after installation of whiteboards formatted with the mnemonic SWIFT (Subject, Why?, Issues, Fetus, Tasks). Handoff transcripts were evaluated by obstetricians blinded to timing and speaker identity. An intraclass correlation coefficient accounted for evaluator differences. Data analysis was by ordinal logistic regression, the generalized estimating equations method (correlated data), and Bonferroni adjustment (multiple comparisons). Forty-five handoffs were evaluated (15 each predidactics, postdidactics, and postwhiteboard revision). Higher completeness scores over time were noted for admission reason, labor concerns, and task list (not statistically significant). Comprehensive score increases prelecture to postwhiteboard were seen in handoff clarity (2.81 versus 2.91) and overall quality (2.77 versus 2.81) (not statistically significant). A subanalysis of four residents who gave multiple handoffs over different periods revealed few significant changes over time. Greater interevaluator consistency was noted with more objective elements. The mnemonic SWIFT, with formalized curricula for obstetrical resident training focusing on new learners and increased faculty involvement and reinforcement, may result in improvement of handoffs on the labor floor.

Evaluating statistical and clinical significance of intervention effects in single-case experimental designs: an SPSS method to analyze univariate data.

Science.gov (United States)

Maric, Marija; de Haan, Else; Hogendoorn, Sanne M; Wolters, Lidewij H; Huizenga, Hilde M

2015-03-01

Single-case experimental designs are useful methods in clinical research practice to investigate individual client progress. Their proliferation might have been hampered by methodological challenges such as the difficulty applying existing statistical procedures. In this article, we describe a data-analytic method to analyze univariate (i.e., one symptom) single-case data using the common package SPSS. This method can help the clinical researcher to investigate whether an intervention works as compared with a baseline period or another intervention type, and to determine whether symptom improvement is clinically significant. First, we describe the statistical method in a conceptual way and show how it can be implemented in SPSS. Simulation studies were performed to determine the number of observation points required per intervention phase. Second, to illustrate this method and its implications, we present a case study of an adolescent with anxiety disorders treated with cognitive-behavioral therapy techniques in an outpatient psychotherapy clinic, whose symptoms were regularly assessed before each session. We provide a description of the data analyses and results of this case study. Finally, we discuss the advantages and shortcomings of the proposed method. Copyright © 2014. Published by Elsevier Ltd.

Validation of a dual-isotope plasma ratio method for measurement of cholesterol absorption in rats

International Nuclear Information System (INIS)

Zilversmit, D.B.; Hughes, L.B.

1974-01-01

Several methods for measuring cholesterol absorption in the rat have been compared. After administration of an oral dose of labeled cholesterol ( 14 C or 3 H) and an intravenous dose of colloidal labeled cholesterol ( 3 H or 14 C) the ratio of the two labels in plasma or whole blood 48 hr or more after dosing compared closely to the ratio of areas under the respective specific activity-time curves. The area ratio method is independent of a time lag between the appearance of oral and intravenous label in the bloodstream. Both measures of cholesterol absorption agree fairly well with a method based on measuring the unabsorbed dietary cholesterol in a pooled fecal sample. The plasma isotope ratio method gave more reproducible results than the fecal collection method when the measurement was repeated in the same animals 5 days after the first measurement. Cholesterol absorption was overestimated by the use of Tween 20-solubilized labeled cholesterol for the intravenous dose. The plasma disappearance curves of injected labeled colloidal cholesterol and cholesterol-labeled chylomicrons infused intravenously over a 3.5-h period in the same animal coincided within experimental error from the first day until 75 days after injection. The plasma isotope ratio method for cholesterol absorption gave the same results in rats practicing coprophagy as in those in which this practice was prevented. The addition of sulfaguanidine to the diet lowered cholesterol absorption as measured by the plasma isotope ratio to the same degree as that measured by the fecal collection method. (U.S.)

Public safety risk management at socio-economic and / or historic-cultural significant dam sites

Energy Technology Data Exchange (ETDEWEB)

Earle, Gordon D.; Ryan, Katherine; Pyykonen, Nicole K.; Pitts, Lucas [Otonabee Region Conservation Authority, Peterborough, (Canada)

2010-07-01

The Lang Dam and adjoining gristmill, located near Peterborough are integral parts of the Lang Pioneer Village museum. Activities occurring within close proximity to the dam have led to safety issues. The owner (ORCA) has developed and implemented public safety management plans (PSMPs) for each of its water control structures, including the Lang Dam. ORCA gave special attention to the social, economic, aesthetic, historic and cultural dimensions associated the implementation of public safety management plans. These factors play a significant role in how well public safety measures (PSMs) are received by stakeholder groups and the general public. This paper reported the challenges of developing and implementing a PSMP for the Lang Dam, with the focus on property site-specific PSMS while preserving socio-economic and historic-cultural character and values. It was demonstrated that the dam owners, regulatory authorities, control agencies and preservationists need to come together to develop a holistic public safety management process.

Reporting on a Talk I Gave Some Months Ago, the Headline in "La Opinion," Los Angeles' Premier Spanish Language Newspaper, Declared the City's School System "en crisis permanente." No One Wrote in to Disagree. The Claremont Letter. Volume 3, Issue 1

Science.gov (United States)

Kerchner, Charles T.

2008-01-01

Reporting on a talk the author gave some months ago, the headline in "La Opinion," Los Angeles' premier Spanish language newspaper, declared the city's school system "en crisis permanente." No one wrote in to disagree. Indeed, at the end of "Learning from L.A.: Institutional Change in American Public Education" (Harvard Education Press) the author…

The GC/MS Analysis of Volatile Components Extracted by Different Methods from Exocarpium Citri Grandis

Directory of Open Access Journals (Sweden)

Zhisheng Xie

2013-01-01

Full Text Available Volatile components from Exocarpium Citri Grandis (ECG were, respectively, extracted by three methods, that is, steam distillation (SD, headspace solid-phase microextraction (HS-SPME, and solvent extraction (SE. A total of 81 compounds were identified by gas chromatography-mass spectrometry including 77 (SD, 56 (HS-SPME, and 48 (SE compounds, respectively. Despite of the extraction method, terpenes (39.98~57.81% were the main volatile components of ECG, mainly germacrene-D, limonene, 2,6,8,10,14-hexadecapentaene, 2,6,11,15-tetramethyl-, (E,E,E-, and trans-caryophyllene. Comparison was made among the three methods in terms of extraction profile and property. SD relatively gave an entire profile of volatile in ECG by long-time extraction; SE enabled the analysis of low volatility and high molecular weight compounds but lost some volatiles components; HS-SPME generated satisfactory extraction efficiency and gave similar results to those of SD at analytical level when consuming less sample amount, shorter extraction time, and simpler procedure. Although SD and SE were treated as traditionally preparative extractive techniques for volatiles in both small batches and large scale, HS-SPME coupled with GC/MS could be useful and appropriative for the rapid extraction and qualitative analysis of volatile components from medicinal plants at analytical level.

How significant is the ‘significant other’? Associations between significant others’ health behaviors and attitudes and young adults’ health outcomes

Directory of Open Access Journals (Sweden)

Berge Jerica M

2012-04-01

Full Text Available Abstract Background Having a significant other has been shown to be protective against physical and psychological health conditions for adults. Less is known about the period of emerging young adulthood and associations between significant others’ weight and weight-related health behaviors (e.g. healthy dietary intake, the frequency of physical activity, weight status. This study examined the association between significant others’ health attitudes and behaviors regarding eating and physical activity and young adults’ weight status, dietary intake, and physical activity. Methods This study uses data from Project EAT-III, a population-based cohort study with emerging young adults from diverse ethnic and socioeconomic backgrounds (n = 1212. Logistic regression models examining cross-sectional associations, adjusted for sociodemographics and health behaviors five years earlier, were used to estimate predicted probabilities and calculate prevalence differences. Results Young adult women whose significant others had health promoting attitudes/behaviors were significantly less likely to be overweight/obese and were more likely to eat ≥ 5 fruits/vegetables per day and engage in ≥ 3.5 hours/week of physical activity, compared to women whose significant others did not have health promoting behaviors/attitudes. Young adult men whose significant other had health promoting behaviors/attitudes were more likely to engage in ≥ 3.5 hours/week of physical activity compared to men whose significant others did not have health promoting behaviors/attitudes. Conclusions Findings suggest the protective nature of the significant other with regard to weight-related health behaviors of young adults, particularly for young adult women. Obesity prevention efforts should consider the importance of including the significant other in intervention efforts with young adult women and potentially men.

Using AMDD method for Database Design in Mobile Cloud Computing Systems

OpenAIRE

Silviu Claudiu POPA; Mihai-Constantin AVORNICULUI; Vasile Paul BRESFELEAN

2013-01-01

The development of the technologies of wireless telecommunications gave birth of new kinds of e-commerce, the so called Mobile e-Commerce or m-Commerce. Mobile Cloud Computing (MCC) represents a new IT research area that combines mobile computing and cloud compu-ting techniques. Behind a cloud mobile commerce system there is a database containing all necessary information for transactions. By means of Agile Model Driven Development (AMDD) method, we are able to achieve many benefits that smoo...

Comparison of direct boiling method with commercial kits for extracting fecal microbiome DNA by Illumina sequencing of 16S rRNA tags.

Science.gov (United States)

Peng, Xin; Yu, Ke-Qiang; Deng, Guan-Hua; Jiang, Yun-Xia; Wang, Yu; Zhang, Guo-Xia; Zhou, Hong-Wei

2013-12-01

Low cost and high throughput capacity are major advantages of using next generation sequencing (NGS) techniques to determine metagenomic 16S rRNA tag sequences. These methods have significantly changed our view of microorganisms in the fields of human health and environmental science. However, DNA extraction using commercial kits has shortcomings of high cost and time constraint. In the present study, we evaluated the determination of fecal microbiomes using a direct boiling method compared with 5 different commercial extraction methods, e.g., Qiagen and MO BIO kits. Principal coordinate analysis (PCoA) using UniFrac distances and clustering showed that direct boiling of a wide range of feces concentrations gave a similar pattern of bacterial communities as those obtained from most of the commercial kits, with the exception of the MO BIO method. Fecal concentration by boiling method affected the estimation of α-diversity indices, otherwise results were generally comparable between boiling and commercial methods. The operational taxonomic units (OTUs) determined through direct boiling showed highly consistent frequencies with those determined through most of the commercial methods. Even those for the MO BIO kit were also obtained by the direct boiling method with high confidence. The present study suggested that direct boiling could be used to determine the fecal microbiome and using this method would significantly reduce the cost and improve the efficiency of the sample preparation for studying gut microbiome diversity. © 2013 Elsevier B.V. All rights reserved.

[Significance of three-dimensional reconstruction as a method of preoperative planning of laparoscopic radiofrequency ablation].

Science.gov (United States)

Zhang, W W; Wang, H G; Shi, X J; Chen, M Y; Lu, S C

2016-09-01

To discuss the significance of three-dimensional reconstruction as a method of preoperative planning of laparoscopic radiofrequency ablation(LRFA). Thirty-two cases of LRFA admitted from January 2014 to December 2015 in Department of Hepatobiliary Surgery, Chinese People's Liberation Army General Hospital were analyzed(3D-LRFA group). Three-dimensional(3D) reconstruction were taken as a method of preoperative planning in 3D-LRFA group.Other 64 LRFA cases were paired over the same period without three-dimensional reconstruction before the operation (LRFA group). Hepatobiliary system contrast enhanced CT scan of 3D-RFA patients were taken by multi-slice spiral computed tomography(MSCT), and the DICOM data were processed by IQQA(®)-Liver and IQQA(®)-guide to make 3D reconstruction.Using 3D reconstruction model, diameter and scope of tumor were measured, suitable size (length and radiofrequency length) and number of RFA electrode were chosen, scope and effect of radiofrequency were simulated, reasonable needle track(s) was planed, position and angle of laparoscopic ultrasound (LUS) probe was designed and LUS image was simulated.Data of operation and recovery were collected and analyzed. Data between two sets of measurement data were compared with t test or rank sum test, and count data with χ(2) test or Fisher exact probability test.Tumor recurrence rate was analyzed with the Kaplan-Meier survival curve and Log-rank (Mantel-Cox) test. Compared with LRFA group ((216.8±66.2) minutes, (389.1±183.4) s), 3D-LRFA group ((173.3±59.4) minutes, (242.2±90.8) s) has shorter operation time(t=-3.138, P=0.002) and shorter mean puncture time(t=-2.340, P=0.021). There was no significant difference of blood loss(P=0.170), ablation rate (P=0.871) and incidence of complications(P=1.000). Compared with LRFA group ((6.3±3.9)days, (330±102)U/L, (167±64)ng/L), 3D-LRFA group ((4.3±3.1) days, (285±102) U/L, (139±43) ng/L) had shorter post-operative stay(t=-2.527, P=0.016), less

What if there were no significance tests?

CERN Document Server

Harlow, Lisa L; Steiger, James H

2013-01-01

This book is the result of a spirited debate stimulated by a recent meeting of the Society of Multivariate Experimental Psychology. Although the viewpoints span a range of perspectives, the overriding theme that emerges states that significance testing may still be useful if supplemented with some or all of the following -- Bayesian logic, caution, confidence intervals, effect sizes and power, other goodness of approximation measures, replication and meta-analysis, sound reasoning, and theory appraisal and corroboration. The book is organized into five general areas. The first presents an overview of significance testing issues that sythesizes the highlights of the remainder of the book. The next discusses the debate in which significance testing should be rejected or retained. The third outlines various methods that may supplement current significance testing procedures. The fourth discusses Bayesian approaches and methods and the use of confidence intervals versus significance tests. The last presents the p...

Evaluation of radiochemical neutron activation analysis methods for determination of arsenic in biological materials.

Science.gov (United States)

Paul, Rick L

2011-01-01

Radiochemical neutron activation analysis (RNAA) with retention on hydrated manganese dioxide (HMD) has played a key role in the certification of As in biological materials at NIST. Although this method provides very high and reproducible yields and detection limits at low microgram/kilogram levels, counting geometry uncertainties may arise from unequal distribution of As in the HMD, and arsenic detection limits may not be optimal due to significant retention of other elements. An alternate RNAA procedure with separation of arsenic by solvent extraction has been investigated. After digestion of samples in nitric and perchloric acids, As(III) is extracted from 2 M sulfuric acid solution into a solution of zinc diethyldithiocarbamate in chloroform. Counting of (76)As allows quantitation of arsenic. Addition of an (77)As tracer solution prior to dissolution allows correction for chemical yield and counting geometries, further improving reproducibility. The HMD and solvent extraction procedures for arsenic were compared through analysis of SRMs 1577c (bovine liver), 1547 (peach leaves), and 1575a (pine needles). Both methods gave As results in agreement with certified values with comparable reproducibility. However, the solvent extraction method yields a factor of 3 improvement in detection limits and is less time-consuming than the HMD method. The new method shows great promise for use in As certification in reference materials.

a Comparison of Tree Segmentation Methods Using Very High Density Airborne Laser Scanner Data

Science.gov (United States)

Pirotti, F.; Kobal, M.; Roussel, J. R.

2017-09-01

Developments of LiDAR technology are decreasing the unit cost per single point (e.g. single-photo counting). This brings to the possibility of future LiDAR datasets having very dense point clouds. In this work, we process a very dense point cloud ( 200 points per square meter), using three different methods for segmenting single trees and extracting tree positions and other metrics of interest in forestry, such as tree height distribution and canopy area distribution. The three algorithms are tested at decreasing densities, up to a lowest density of 5 point per square meter. Accuracy assessment is done using Kappa, recall, precision and F-Score metrics comparing results with tree positions from groundtruth measurements in six ground plots where tree positions and heights were surveyed manually. Results show that one method provides better Kappa and recall accuracy results for all cases, and that different point densities, in the range used in this study, do not affect accuracy significantly. Processing time is also considered; the method with better accuracy is several times slower than the other two methods and increases exponentially with point density. Best performer gave Kappa = 0.7. The implications of metrics for determining the accuracy of results of point positions' detection is reported. Motives for the different performances of the three methods is discussed and further research direction is proposed.

Stresses in reinforced nozzle-cylinder attachments under internal pressure loading analyzed by the finite-element method: a parameter study

International Nuclear Information System (INIS)

Bryson, J.W.; Johnson, W.G.; Bass, B.R.

1977-01-01

A parameter study was conducted on stresses in reinforced nozzle-to-cylinder attachments under internal pressure loading as analyzed by the finite-element method. Twenty-five models with branch-to-run diameter ratios 0.08 less than or equal to d/D less than or equal to 0.50 and run diameter-to-thickness ratios 10 less than or equal to D/T less than or equal to 100 were investigated. A three-dimensional finite-element program, CORTES-SA, which was developed at the University of California at Berkeley specifically for analyzing tee-joint configurations, was used in the study. It was concluded from the study that both of the reinforcement designs investigated significantly reduce maximum stresses relative to configurations having little or no reinforcement. For internal pressure loading, neither of the reinforcement designs offered a significant advantage over the other in that both types of reinforcement gave very nearly the same maximum stresses

Evaluation of methods for available Zn in four soil orders in Costa Rica

International Nuclear Information System (INIS)

Molina, E.; Bornemisza, E.

2001-01-01

Analytical methods for available Zn determination were evaluated on four soil orders in Costa Rica (Ultisols, Vertisols, Inceptisols and Andisols) with 25 samples for each; using the following extract solutions : Modified Olsen, Mehlich 3, Modified Morgan , DTPA and HCI. The Zn levels obtained depended on the chemical characteristics of the extracting solutions. The highest levels were obtained with HCI, except for the Vertisols. The solutions with EDTA (Modified Olsen and Mehlich 3), extracted intermediate levels of Zn, while the method using DTPA (Modified Morgan and DTPA) gave the lowest Zn values . In most of the cases, significant values of correlation were obtained between the 5 extraction methods; so for individual soil orders, or comparing all 100 soils. The highest correlation coefficients for extractable Zn were found for the Mehlich 3, Modified Morgan and DTPA. The correlations were consistent for the 4 orders, which indicate that they are adaptable to different soils, a useful characteristic for these methods. The Modified Olsen was the most efficient extractor in slightly acis soils (Vertisols and Inceptisols). The HCI extracted very high Zn levels, which are probably not related to plant available forms. It is concluded that the Mehlich 3, Modified Morgan and DTPA solutions are probably adequate for available Zn determination and might present an alternative to substitute the generally used Modified Olsen solution in Costa Rica. (Author) [es

Secondary dentine as a sole parameter for age estimation: Comparison and reliability of qualitative and quantitative methods among North Western adult Indians

Directory of Open Access Journals (Sweden)

Jasbir Arora

2016-06-01

Full Text Available The indestructible nature of teeth against most of the environmental abuses makes its use in disaster victim identification (DVI. The present study has been undertaken to examine the reliability of Gustafson’s qualitative method and Kedici’s quantitative method of measuring secondary dentine for age estimation among North Western adult Indians. 196 (M = 85; F = 111 single rooted teeth were collected from the Department of Oral Health Sciences, PGIMER, Chandigarh. Ground sections were prepared and the amount of secondary dentine formed was scored qualitatively according to Gustafson’s (0–3 scoring system (method 1 and quantitatively following Kedici’s micrometric measurement method (method 2. Out of 196 teeth 180 samples (M = 80; F = 100 were found to be suitable for measuring secondary dentine following Kedici’s method. Absolute mean error of age was calculated by both methodologies. Results clearly showed that in pooled data, method 1 gave an error of ±10.4 years whereas method 2 exhibited an error of approximately ±13 years. A statistically significant difference was noted in absolute mean error of age between two methods of measuring secondary dentine for age estimation. Further, it was also revealed that teeth extracted for periodontal reasons severely decreased the accuracy of Kedici’s method however, the disease had no effect while estimating age by Gustafson’s method. No significant gender differences were noted in the absolute mean error of age by both methods which suggest that there is no need to separate data on the basis of gender.

GABA content and Antioxidant activity of Thai waxy corn seeds germinated by hypoxia method

Directory of Open Access Journals (Sweden)

Pisamai Polthum

2014-06-01

Full Text Available Germinated seeds have a greater amount of the naturally-occurring -aminobutyric acid (GABA which has many health benefits. Further, colored seeds have higher antioxidant activity. Thai waxy corn is widely consumed after cooking, due to its palatable glutinous texture. However, it is not commonly germinated before use. In this study, two varieties of Thai waxy corn, KKU-KND (purple seed and KKU-SLE (white seed, were germinated and converted to corn flour with the aim of investigating the effect of germination on GABA content and antioxidant activity. Further, the microstructure of starch granules was also examined. KKU-KND and KKU-SLE were grown and harvested in 2012. The seeds were soaked in distilled water for 6 hrs to attain a moisture content of 31-32%wb and then germinated by employing two methods, i in an open plastic box, and ii in a closed plastic box with a headspace of 3 cm for devoid oxygen (hypoxia method; the germination period varied between 12-48 hrs at 35±2°C in both cases. The germinated samples were then dried at 50°C to a moisture content of 10±2%wb. The results showed that non-germinated KKU-KND and KKU-SLE contained 2.68±0.77 and 1.58±0.05 mgGABA/ 100gdb, respectively, whereas the samples germinated by the hypoxia method contained significantly higher GABA which increased with germination time (p<0.05. The highest GABA contents found in KKU-KND and KKU-SLE were 37.20±3.27 and 54.47±2.08 mg/100gdb, respectively after 48 hrs of germination under the hypoxia method. In addition, the germinated KKU-KND gave ABTS and DPPH values of 388.32±0.53 and 140.29±0.57 mgTrolox/100gdb, whereas the germinated KKU-SLE gave ABTS and DPPH values of 183.69±1.75 and 38.43±1.64 mgTrolox/100gdb, respectively. The pictures of starch granules obtained by means of SEM displayed differences in the shape and size of the non-germinated and germinated granules in both verities. In conclusion, the hypoxia method is able to induce higher GABA

Effectiveness of Smoking Cessation and Reduction in Pregnancy Treatment (SCRIPT) Methods in Medicaid-Supported Prenatal Care: Trial III

Science.gov (United States)

Windsor, Richard; Woodby, Lesa; Miller, Thomas; Hardin, Michael

2011-01-01

This two-phase evaluation documented the delivery and effectiveness of evidence-based health education methods by regular staff to pregnant smokers. During Phase 1, a total of 436 Medicaid patients were screened and 416 (95%) gave consent: 334 nonsmokers and 102 smokers. This historical Comparison (C) group was assessed to document the "normal"…

CASE METHOD. ACTIVE LEARNING METHODOLOGY TO ACQUIRE SIGNIFICANT IN CHEMISTRY

Directory of Open Access Journals (Sweden)

Clotilde Pizarro

2015-09-01

Full Text Available In this paper the methodology of cases in first year students of the Engineering Risk Prevention and Environment is applied. For this purpose a real case of contamination occurred at a school in the region of Valparaiso called "La Greda" is presented. If the application starts delivering an extract of the information collected from the media and they made a brief induction on the methodology to be applied. A plenary session, which is debate about possible solutions to the problem and establishing a relationship between the case and drives the chemistry program is then performed. Is concluded that the application of the case method, was a fruitful tool in yields obtained by students, since the percentage of approval was 75%, which is considerably higher than previous years.

Off-flavor related volatiles in soymilk as affected by soybean variety, grinding, and heat-processing methods.

Science.gov (United States)

Zhang, Yan; Guo, Shuntang; Liu, Zhisheng; Chang, Sam K C

2012-08-01

Off-flavor of soymilk is a barrier to the acceptance of consumers. The objectionable soy odor can be reduced through inhibition of their formation or through removal after being formed. In this study, soymilk was prepared by three grinding methods (ambient, cold, and hot grinding) from two varieties (yellow Prosoy and a black soybean) before undergoing three heating processes: stove cooking, one-phase UHT (ultrahigh temperature), and two-phase UHT process using a Microthermics direct injection processor, which was equipped with a vacuuming step to remove injected water and volatiles. Eight typical soy odor compounds, generated from lipid oxidation, were extracted by a solid-phase microextraction method and analyzed by gas chromatography. The results showed that hot grinding and cold grinding significantly reduced off-flavor as compared with ambient grinding, and hot grinding achieved the best result. The UHT methods, especially the two-phase UHT method, were effective to reduce soy odor. Different odor compounds showed distinct concentration patterns because of different formation mechanisms. The two varieties behaved differently in odor formation during the soymilk-making process. Most odor compounds could be reduced to below the detection limit through a combination of hot grinding and two-phase UHT processing. However, hot grinding gave lower solid and protein recoveries in soymilk.

Investigating water productivity and economic efficiency of wheat-crop under different sowing methods

International Nuclear Information System (INIS)

Mirani, A.A.; Dahri, Z.H.

2011-01-01

This study was conducted at PARC's research station Kala Shah Kaku, Lahore, in order to calculate the water productivity and economic efficiency of wheat-crop under different sowing methods in a combined harvested paddy filed. The sowing methods were direct drilling with FMI Seeder, Zero tillage and conventional method. Data were collected during 2008-09. Wheat-yield was 2750 kg/ha, 2665 kg/ha and 2610 kg/ha for direct drilling with F MI Seeder, Zero tillage and conventional method, respectively. The direct drilling in heavy residue gave 5.4 % more yield than the conventional method and 3.2 % more yield than zero tillage. The zero tillage ensured 2.1% more yield than the conventional method. The net water applied as 323, 354, and 380 mm for direct drilling with FMI seeder, zero tillage and conventional methods respectively against the potential crop evapotranspiration of 383 mm. This indicates that the direct drilling of wheat-crop in heave rice stubbles saves 15% irrigation water as compared to conventional method and 8.8% over zero tillage. The zero tillage method saves 6.8 % of irrigation water over the conventional method. The water productivity was found to be 0.851 kg/m3. 0.753 kg/m/sup 3/ and 0.687 kg/m/sup 3/ for direct drilling with FMI Seeder, Zero tillage and conventional method respectively. This indicates that the direct drilling ensures 23.9% increase in water productivity over conventional method and 13.01% over zero tillage. The zero tillage gave 9.6% more water productivity than the conventional method. The costs of production for the three sowing methods were Rs. 39123/ha, Rs.43737/ha and Rs. 53047/ha for direct drilling, zero tillage and conventional method respectively. This indicates an overall saving of Rs. 13924/ha (26.2 %) by the direct drilling method as compared to the conventional method and Rs. 4613/ha (10.5%) over zero tillage method. The zero tillage saves Rs. 9319/ha (17.6 %) over the conventional method. Thus, the resource

Fine mapping of multiple QTL using combined linkage and linkage disequilibrium mapping – A comparison of single QTL and multi QTL methods

Directory of Open Access Journals (Sweden)

Meuwissen Theo HE

2007-04-01

Full Text Available Abstract Two previously described QTL mapping methods, which combine linkage analysis (LA and linkage disequilibrium analysis (LD, were compared for their ability to detect and map multiple QTL. The methods were tested on five different simulated data sets in which the exact QTL positions were known. Every simulated data set contained two QTL, but the distances between these QTL were varied from 15 to 150 cM. The results show that the single QTL mapping method (LDLA gave good results as long as the distance between the QTL was large (> 90 cM. When the distance between the QTL was reduced, the single QTL method had problems positioning the two QTL and tended to position only one QTL, i.e. a "ghost" QTL, in between the two real QTL positions. The multi QTL mapping method (MP-LDLA gave good results for all evaluated distances between the QTL. For the large distances between the QTL (> 90 cM the single QTL method more often positioned the QTL in the correct marker bracket, but considering the broader likelihood peaks of the single point method it could be argued that the multi QTL method was more precise. Since the distances were reduced the multi QTL method was clearly more accurate than the single QTL method. The two methods combine well, and together provide a good tool to position single or multiple QTL in practical situations, where the number of QTL and their positions are unknown.

Clustering Methods Application for Customer Segmentation to Manage Advertisement Campaign

Directory of Open Access Journals (Sweden)

Maciej Kutera

2010-10-01

Full Text Available Clustering methods are recently so advanced elaborated algorithms for large collection data analysis that they have been already included today to data mining methods. Clustering methods are nowadays larger and larger group of methods, very quickly evolving and having more and more various applications. In the article, our research concerning usefulness of clustering methods in customer segmentation to manage advertisement campaign is presented. We introduce results obtained by using four selected methods which have been chosen because their peculiarities suggested their applicability to our purposes. One of the analyzed method k-means clustering with random selected initial cluster seeds gave very good results in customer segmentation to manage advertisement campaign and these results were presented in details in the article. In contrast one of the methods (hierarchical average linkage was found useless in customer segmentation. Further investigations concerning benefits of clustering methods in customer segmentation to manage advertisement campaign is worth continuing, particularly that finding solutions in this field can give measurable profits for marketing activity.

Comparison of different extraction methods and HPLC quantification of prenylated and unprenylated phenylpropanoids in raw Italian propolis.

Science.gov (United States)

Taddeo, Vito Alessandro; Epifano, Francesco; Fiorito, Serena; Genovese, Salvatore

2016-09-10

In this paper the presence of selected prenylated and unprenylated phenylpropanoids, namely ferulic acid 1, boropinic acid 2, 4'-geranyloxyferulic acid 3, umbelliferone 4, 7-isopentenyloxycoumarin 5, and auraptene 6, have been determined in Italian raw propolis after having been extracted with different methodologies. An aqueous solution of β-cyclodextrin was the best extraction method for ferulic acid 1, treatment with indifferently EtOH or aqueous β-cyclodextrin were the most effective one for umbelliferone 4, boropinic acid 2 gave the best yields either with H2O/β-cyclodextrin or olive oil treatment or in biphasic systems, maceration with biphasic mixtures of aqueous β-cyclodextrin and olive oil was seen to be the most effective procedure for 7-isopentenyloxycoumarin 5, the only method providing significant quantities of 4'-geranyloxyferulic acid 3 was the maceration of raw propolis with olive oil, and finally auraptene 4 was best extracted with absolute EtOH. "Classic" maceration in general performed better than ultrasound-assisted one. Copyright © 2016 Elsevier B.V. All rights reserved.

Selective adsorption-desorption method for the enrichment of krypton

International Nuclear Information System (INIS)

Yuasa, Y.; Ohta, M.; Watanabe, A.; Tani, A.; Takashima, N.

1975-01-01

Selective adsorption-desorption method has been developed as an effective means of enriching krypton and xenon gases. A seriesof laboratory-scale tests were performed to provide some basic data of the method when applied to off-gas streams of nuclear power plants. For the first step of the enrichment process of the experiments, krypton was adsorbed on solid adsorbents from dilute mixtures with air at temperatures ranging from -50 0 C to -170 0 C. After the complete breakthrough was obtained, the adsorption bed was evacuated at low temperature by a vacuum pump. By combining these two steps krypton was highly enriched on the adsorbents, and the enrichment factor for krypton was calculated as the product of individual enrichment factors of each step. Two types of adsorbents, coconut charcoal and molecular sieves 5A, were used. Experimental results showed that the present method gave the greater enrichment factor than the conventional method which used selective adsorption step only. (U.S.)

SRS Process Facility Significance Fire Frequency

Energy Technology Data Exchange (ETDEWEB)

Sarrack, A.G. [Westinghouse Savannah River Company, AIKEN, SC (United States)

1995-10-01

This report documents the method and assumptions of a study performed to determine a site generic process facility significant fire initiator frequency and explains the proper way this value should be used.

SRS Process Facility Significance Fire Frequency

International Nuclear Information System (INIS)

Sarrack, A.G.

1995-10-01

This report documents the method and assumptions of a study performed to determine a site generic process facility significant fire initiator frequency and explains the proper way this value should be used

Comparison of RNA extraction methods in Thai aromatic coconut water

Directory of Open Access Journals (Sweden)

Nopporn Jaroonchon

2015-10-01

Full Text Available Many researches have reported that nucleic acid in coconut water is in free form and at very low yields which makes it difficult to process in molecular studies. Our research attempted to compare two extraction methods to obtain a higher yield of total RNA in aromatic coconut water and monitor its change at various fruit stages. The first method used ethanol and sodium acetate as reagents; the second method used lithium chloride. We found that extraction using only lithium chloride gave a higher total RNA yield than the method using ethanol to precipitate nucleic acid. In addition, the total RNA from both methods could be used in amplification of betaine aldehyde dehydrogenase2 (Badh2 genes, which is involved in coconut aroma biosynthesis, and could be used to perform further study as we expected. From the molecular study, the nucleic acid found in coconut water increased with fruit age.

A rapid cycleave PCR method for distinguishing the vaccine strain Brucella abortus A19 in China.

Science.gov (United States)

Nan, Wenlong; Zhang, Yueyong; Tan, Pengfei; Xu, Zouliang; Chen, Yuqi; Mao, Kairong; Chen, Yiping

2016-05-01

Brucellosis is a widespread zoonotic disease caused by Brucella spp. Immunization with attenuated vaccines has proved to be an effective method of prevention; however, it may also interfere with diagnosis. Brucella abortus strain A19, which is homologous to B. abortus strain S19, is widely used for the prevention of bovine brucellosis in China. For effective monitoring of the control of brucellosis, it is essential to distinguish A19 from field strains. Single-nucleotide polymorphism-based assays offer a new approach to such discrimination studies. In the current study, we developed a cycleave PCR assay that successfully distinguished attenuated vaccine strains A19 and S19 from 22 strains of B. abortus and 57 strains of 5 other Brucella species. The assay gave a negative reaction with 4 non-Brucella species. The minimum sensitivity of the assay, evaluated using 10-fold dilutions of chromosomal DNA, was 7.6 fg for the A19 strain and 220 fg for the single non-A19/non-S19 Brucella strain tested (B. abortus 104M). The assay was also reproducible (intra- and interassay coefficients of variation: 0.003-0.01 and 0.004-0.025, respectively). The cycleave assay gave an A19/S19-specific reaction in 3 out of 125 field serum samples, with the same 3 samples being positive in an alternative A19/S19-specific molecular assay. The cycleave assay gave a total of 102 Brucella-specific reactions (3 being the A19/S19-specific reactions), whereas an alternative Brucella-specific assay gave 92 positive reactions (all also positive in the cycleave assay). Therefore, this assay represents a simple, rapid, sensitive, and specific tool for use in brucellosis control. © 2016 The Author(s).

[Significances of the life experience for the long-lived elderly person in the process of death/dying and mourning].

Science.gov (United States)

Menezes, Tânia Maria de Oliva; Lopes, Regina Lúcia Mendonça

2014-08-01

This is a study using the Heideggerian theoretical-phenomenological approach, which sought to understand the significances of the life experience for the long-lived elderly person in the process of death/dying and mourning. It was conducted in 2009 with 16 long-lived senior citizens of both genders who were aged between 80 and 90, members of a community center for the elderly located in a suburban neighborhood of the city of Salvador in the state of Bahia, Brazil. The results showed that the long-lived elderly person experiences the mourning status process when relatives and friends become ill and die. Furthermore, they gave ambiguous reports with respect to the fear of death. With the attributed significances, it was possible to arrive at the unit of significance, namely the authenticity and lack of authenticity of the individual regarding imminent death. The conclusion reached is that long-lived elderly individuals faced with the process of death/dying and mourning is apparent or concealed in accordance with the moment they are experiencing and the opportunities that present themselves, in other words, it is greatly influenced by their past.

Liquid wastes from mining and milling of uranium ores - a laboratory study of treatment methods

International Nuclear Information System (INIS)

Ryan, R.K.; Alfredson, P.G.

1976-10-01

Methods of reducing the concentration of contaminants in mine water and in the acidic raffinate from uranium milling operations have been studied. Lime, limestone, caustic soda and lime-soda ash mixtures were compared as reagents for neutralising raffinates and for removing amines and heavy metals including radium from solution. All methods of neutralisation reduced contaminant levels significantly. Two-stage neutralisation using limestone in the first stage to pH 4, followed by second stage lime treatment appears to be an economically attractive approach. This method usually gave the lowest residual radium concentration provided the solids from the first stage were not removed before adding lime. Radium can be further removed from neutralised raffinates or from mine water conditioned with sulphate by the addition of barium chloride to co-precipitate the sulphates of barium and radium. The concentration of radium was readily reduced to less than 3 pCi l -1 by adding 10 mg Ba l -1 raffinate. For mine waters conditioned to 0.01 M in sulphate, barium additions of 20 mg l -1 were required to attain the same radium concentrations. Adsorption on barytes was also effective in removing radium from conditioned mine water and neutralised raffinates. (author)

Bayesian mixture modeling of significant p values: A meta-analytic method to estimate the degree of contamination from H₀.

Science.gov (United States)

Gronau, Quentin Frederik; Duizer, Monique; Bakker, Marjan; Wagenmakers, Eric-Jan

2017-09-01

Publication bias and questionable research practices have long been known to corrupt the published record. One method to assess the extent of this corruption is to examine the meta-analytic collection of significant p values, the so-called p -curve (Simonsohn, Nelson, & Simmons, 2014a). Inspired by statistical research on false-discovery rates, we propose a Bayesian mixture model analysis of the p -curve. Our mixture model assumes that significant p values arise either from the null-hypothesis H ₀ (when their distribution is uniform) or from the alternative hypothesis H1 (when their distribution is accounted for by a simple parametric model). The mixture model estimates the proportion of significant results that originate from H ₀, but it also estimates the probability that each specific p value originates from H ₀. We apply our model to 2 examples. The first concerns the set of 587 significant p values for all t tests published in the 2007 volumes of Psychonomic Bulletin & Review and the Journal of Experimental Psychology: Learning, Memory, and Cognition; the mixture model reveals that p values higher than about .005 are more likely to stem from H ₀ than from H ₁. The second example concerns 159 significant p values from studies on social priming and 130 from yoked control studies. The results from the yoked controls confirm the findings from the first example, whereas the results from the social priming studies are difficult to interpret because they are sensitive to the prior specification. To maximize accessibility, we provide a web application that allows researchers to apply the mixture model to any set of significant p values. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

A Validated Reverse Phase HPLC Analytical Method for Quantitation of Glycoalkaloids in Solanum lycocarpum and Its Extracts

Directory of Open Access Journals (Sweden)

Renata Fabiane Jorge Tiossi

2012-01-01

Full Text Available Solanum lycocarpum (Solanaceae is native to the Brazilian Cerrado. Fruits of this species contain the glycoalkaloids solasonine (SN and solamargine (SM, which display antiparasitic and anticancer properties. A method has been developed for the extraction and HPLC-UV analysis of the SN and SM in different parts of S. lycocarpum, mainly comprising ripe and unripe fruits, leaf, and stem. This analytical method was validated and gave good detection response with linearity over a dynamic range of 0.77–1000.00 μg mL−1 and recovery in the range of 80.92–91.71%, allowing a reliable quantitation of the target compounds. Unripe fruits displayed higher concentrations of glycoalkaloids (1.04% ± 0.01 of SN and 0.69% ± 0.00 of SM than the ripe fruits (0.83% ± 0.02 of SN and 0.60% ± 0.01 of SM. Quantitation of glycoalkaloids in the alkaloidic extract gave 45.09% ± 1.14 of SN and 44.37% ± 0.60 of SM, respectively.

Prediction of retention in micellar electrokinetic chromatography based on molecular structural descriptors by using the heuristic method

International Nuclear Information System (INIS)

Liu Huanxiang; Yao Xiaojun; Liu Mancang; Hu Zhide; Fan Botao

2006-01-01

Based on calculated molecular descriptors from the solutes' structure alone, the micelle-water partition coefficients of 103 solutes in micellar electrokinetic chromatography (MEKC) were predicted using the heuristic method (HM). At the same time, in order to show the influence of different molecular descriptors on the micelle-water partition of solute and to well understand the retention mechanism in MEKC, HM was used to build several multivariable linear models using different numbers of molecular descriptors. The best 6-parameter model gave the following results: the square of correlation coefficient R 2 was 0.958 and the mean relative error was 3.98%, which proved that the predictive values were in good agreement with the experimental results. From the built model, it can be concluded that the hydrophobic, H-bond, polar interactions of solutes with the micellar and aqueous phases are the main factors that determine their partitioning behavior. In addition, this paper provided a simple, fast and effective method for predicting the retention of the solutes in MEKC from their structures and gave some insight into structural features related to the retention of the solutes

Proceeding of 35th domestic symposium on applications of structural reliability and risk assessment methods to nuclear power plants

International Nuclear Information System (INIS)

2005-06-01

As the 35th domestic symposium of Atomic Energy Research Committee, the Japan Welding Engineering Society, the symposium was held titled as Applications of structural reliability/risk assessment methods to nuclear energy'. Six speakers gave lectures titled as 'Structural reliability and risk assessment methods', 'Risk-informed regulation of US nuclear energy and role of probabilistic risk assessment', 'Reliability and risk assessment methods in chemical plants', 'Practical structural design methods based on reliability in architectural and civil areas', 'Maintenance activities based on reliability in thermal power plants' and 'LWR maintenance strategies based on Probabilistic Fracture Mechanics'. (T. Tanaka)

Effect of pre-cooking methods on the chemical and sensory deterioration of ready-to-eat chicken patties during chilled storage and microwave reheating.

Science.gov (United States)

Ferreira, Valquíria C S; Morcuende, David; Madruga, Marta S; Hernández-López, Silvia H; Silva, Fábio A P; Ventanas, Sonia; Estévez, Mario

2016-06-01

The effects of pre-cooking methods, namely, boiling (BL), roasting (RT) and grilling (GR), refrigerated storage (14 days/+4 °C) and microwave reheating on chicken patties were studied. Physical, chemical and sensory parameters were evaluated in order to correlate the chemical deterioration of ready-to-eat chicken patties with the acceptance of the odor. Chemical deterioration was evaluated through the chemical composition, Maillard compounds, Thiobarbituric acid-reactive substances (TBARS) and volatiles. Sensory deterioration (odor liking) was performed by an acceptance test with hedonic scale. According to the TBARS values and volatile compounds generated in the head space during the examined stages, the pre-cooking method and the storage time had a significant effect on lipid oxidation, whereas reheating in a microwave had a negligible impact. At each succeeding processing stage, panelists gave lower odor scores to all samples and no significant differences were found between treatments at any stage. RT and GR patties showed less intense chemical changes and presented higher acceptation scores by the sensory panel than BL patties. Thus, the choice of pre-cooking method and control of storage conditions plays a key role in the inhibition of oxidative changes in ready-to-eat chicken patties.

The clinical significance of computerized axial tomography (CAT) in consideration of conventional diagnostic methods

International Nuclear Information System (INIS)

Huenig, R.

1976-01-01

Regarding CAT of the intracranial region, the article informs on a) techniques of examination including the production of normal structures, b) the recognizable pathological changes, c) possibilities of enhancement, d) possibilities of course observation, e) limitations of the methods, as well as on f) risk/benefit aspects g) benefit/cost calculations as compared to conventional methods, and on h) the influence of CAT on the frequency of conventional methods of examination. Regarding CAT of the extracranial region, the information available up to the meeting is reported on. (orig./LH) [de

Evaluation of the essential oil of Foeniculum vulgare Mill (fennel) fruits extracted by three different extraction methods by GC/MS.

Science.gov (United States)

Hammouda, Faiza M; Saleh, Mahmoud A; Abdel-Azim, Nahla S; Shams, Khaled A; Ismail, Shams I; Shahat, Abdelaaty A; Saleh, Ibrahim A

2014-01-01

Hydrodistillation (HD) and steam-distillation, or solvent extraction methods of essential oils have some disadvantages like thermal decomposition of extracts, its contamination with solvent or solvent residues and the pollution of residual vegetal material with solvent which can be also an environmental problem. Thus, new green techniques, such as supercritical fluid extraction and microwave assisted techniques, are potential solutions to overcome these disadvantages. The aim of this study was to evaluate the essential oil of Foeniculum vulgare subsp. Piperitum fruits extracted by three different extraction methods viz. Supercritical fluid extraction (SFE) using CO2, microwave-assisted extraction (MAE) and hydro-distillation (HD) using gas chromatography-mass spectrometry (GC/MS). The results revealed that both MAE and SFE enhanced the extraction efficiency of the interested components. MAE gave the highest yield of oil as well as higher percentage of Fenchone (28%), whereas SFE gave the highest percentage of anethol (72%). Microwave-assisted extraction (MAE) and supercritical fluid extraction (SFE) not only enhanced the essential oil extraction but also saved time, reduced the solvents use and produced, ecologically, green technologies.

A 2-step cooking method of searing and hot water pasteurization to maximize the safety of refrigerated, vacuum packaged, chicken breast meat.

Science.gov (United States)

Enns, D K; Crandall, P G; O'Bryan, C A; Griffis, C L; Martin, E M

2007-05-01

Americans consume almost 40 kg per capita of chicken each year. Increasing consumption of chicken surpassed pork in 1982 and beef in 1992. The objectives of this study were to examine the effectiveness of a novel, 2-step cooking method of grilling, slicing, vacuum packaging, and hot water pasteurization to inhibit the growth of Listeria monocytogenes in chicken breast meat. Because this study required the use of pilot plant scale pasteurization equipment, Listeria innocua M1, a nonpathogen with slightly greater heat resistance than L. monocytogenes, was used as a surrogate. We first examined the lethal effects of grilling on a boneless skinless chicken breast to mimic cross-contaminated, surface-inoculated Listeria. Searing produced a mean reduction of 2.5 log CFU/g of Listeria and a moisture loss of only 7% (w/w). A 2nd experiment studied the lethal effect of pasteurization of the sliced seared chicken breast. L. innocua M1 inoculated between the slices mimicked contamination in deep muscle. Pasteurization in a 71 degrees C bath (final internal temperature of 66 degrees C) gave an additional 2.3 log CFU/g reduction. L. innocua M1 did not show significant regrowth during a wk of refrigerated storage. The combined 2-step cooking method of searing and pasteurization gave a combined 4.8 log reduction in LI M1. In parallel tests a non-Listeria indicator, Corynebacterium glutamicum, inoculated between sliced, seared chicken, showed a 3 log reduction after pasteurization for 10 min in a 71 degrees C bath compared to 2.3 log reduction of Listeria. Corynebacterium regrowth occurred much faster than did L. innocua M1.

Evaluation of a method to determine the myocardial uptake from 123I-BMIPP myocardial SPECT and its significance

International Nuclear Information System (INIS)

Iwase, Mikio; Toriyama, Takayuki; Itou, Masato; Shimao, Ryuichiro; Ikeda, Koshiro; Suzuki, Takeshi; Nobuta, Takaaki; Iida, Akihiko.

1996-01-01

We examined methods of calculating myocardial uptake (TU) of 123 I-BMIPP by SPECT, and compared TU to heart function (ejection fraction (EF), cardiac output (CO), cardiac index (CI)) calculated by left ventriculography. Forty-two patients with acute myocardial infarction were classified into 5 groups; within 1 week (I), from 1 to 2 weeks (II), from 2 weeks to 1.5 months (III), from 1.5 to 3 months (IV) and more than 3 months (V) after percutaneous transluminal coronary angioplasty (PTCA). Chest depth (Tw) was calculated by measuring the thoracic absorption rate of 123 I. In calculating TU, the myocardial count was calculated from short-axis tomograms, and then absorption was corrected using Tw to calculate each value on early-phase image (E) and delay-phase image (D). The influence of lung uptake on myocardial count was only 1.76%. When TU was compared to heart function, there were correlations between group I and group V. Especially in group VD-TU was a significantly correlated with heart function. In heart function CI, but not EF nor CO, was significantly correlated with TU. It was suggested that the correlation between TU and heart function reflected the infarct condition before PTCA in group I, and that the individual difference in recovery of fatty acid metabolism in group V. The significant correlation between D-TU and CI suggests that D-TU reflects heart function and fatty acid metabolism, although TU is influenced by differences in physical status. (author)

Methods for Predicting Tail Control Effects on Conical Afterbodies of Submersibles

Science.gov (United States)

1982-08-01

vehicles have not received the attention they warrant. It is dea3irable to develop such methods to avoid expensive and time- comsuming parametric studies of...data except for the PR = 0.5 fin very well. The M = 0.5 fin gave a very large value of kT as well as a very rearward (x c/c r)T(). This behavior ...lines could be made to fit the data within the scatter bands with good accuracy. However, it was found that the s/R family exhibited quadratic behavior

Theoretical Significance in Q Methodology: A Qualitative Approach to a Mixed Method

Science.gov (United States)

Ramlo, Susan

2015-01-01

Q methodology (Q) has offered researchers a unique scientific measure of subjectivity since William Stephenson's first article in 1935. Q's focus on subjectivity includes self-referential meaning and interpretation. Q is most often identified with its technique (Q-sort) and its method (factor analysis to group people); yet, it consists of a…

Cretaceous choristoderan reptiles gave birth to live young

Science.gov (United States)

Ji, Qiang; Wu, Xiao-Chun; Cheng, Yen-Nien

2010-04-01

Viviparity (giving birth to live young) in fossil reptiles has been known only in a few marine groups: ichthyosaurs, pachypleurosaurs, and mosasaurs. Here, we report a pregnant specimen of the Early Cretaceous Hyphalosaurus baitaigouensis, a species of Choristodera, a diapsid group known from unequivocal fossil remains from the Middle Jurassic to the early Miocene (about 165 to 20 million years ago). This specimen provides the first evidence of viviparity in choristoderan reptiles and is also the sole record of viviparity in fossil reptiles which lived in freshwater ecosystems. This exquisitely preserved specimen contains up to 18 embryos arranged in pairs. Size comparison with small free-living individuals and the straight posture of the posterior-most pair suggest that those embryos were at term and had probably reached parturition. The posterior-most embryo on the left side has the head positioned toward the rear, contrary to normal position, suggesting a complication that may have contributed to the mother’s death. Viviparity would certainly have freed species of Hyphalosaurus from the need to return to land to deposit eggs; taking this advantage, they would have avoided intense competition with contemporaneous terrestrial carnivores such as dinosaurs.

Radionuclide methods in semiconductor technology. I

International Nuclear Information System (INIS)

Stverak, B.; Kopejtko, J.; Janu, M.

1977-01-01

The effects were studied of gold coating (by wetting, dropping and vacuum coating) the surface of silicon plates, the effect of wetting time and drying time on the homogeneity and amount of gold in the thus formed diffusion source. The tracer method was used with 198 Au in form of aqueous solutions of chloroauric acid. The solutions were deposited on the surface of the plate, then dried, the plate rinsed with distilled water and wetted in a KCN solution or in aqua regia. Some plates were then used in the process of thermal diffusion. The method of contact autoradiography was used for the determination of the homogeneity of gold, the amount of gold was determined radiometrically. The duration of wetting was 1, 2, 4, 16 and 32 minutes for two different concentrations of chloroauric acid, the duration of drying was 1, 2.5, 4 and 20 hours. It was ascertained that all gold in its reduced metallic form deposited on the surface could by rinsing in the KCN solution be quantitatively transferred into the solution. Rinsing in aqua regia gave the same results. In depositing gold in form of aqueous solutions of chloroauric acid it was ascertained that regardless of the concentration of gold in the wetting solution the amount of gold insoluble in water stabilized on the surface within approximately 5 minutes. The amount of reduced gold increased (owing to the continuing hydrolysis in the liquid phase) with the increasing drying time of the aqueous solution of chloroauric acid. Gold coating from the liquid phase be it by wetting or by dropping yielded a significantly nonhomogeneous surface layer of deposited gold provided the said solutions of chloroauric acid were used. Considerable differences were ascertained in the surface density of gold between places where the solution had dried and places where it had not remained. Homogeneity significantly improved after rinsing. Following thermal diffusion, 0.8-5% of the total gold content was diffused into the silicon plates. The

An analytical investigation on unsteady motion of vertically falling spherical particles in non-Newtonian fluid by Collocation Method

Directory of Open Access Journals (Sweden)

M. Rahimi-Gorji

2015-06-01

Full Text Available An analytical investigation is applied for unsteady motion of a rigid spherical particle in a quiescent shear-thinning power-law fluid. The results were compared with those obtained from Collocation Method (CM and the established Numerical Method (Fourth order Runge–Kutta scheme. It was shown that CM gave accurate results. Collocation Method (CM and Numerical Method are used to solve the present problem. We obtained that the CM which was used to solve such nonlinear differential equation with fractional power is simpler and more accurate than series method such as HPM which was used in some previous works by others but the new method named Akbari-Ganji’s Method (AGM is an accurate and simple method which is slower than CM for solving such problems. The terminal settling velocity—that is the velocity at which the net forces on a falling particle eliminate—for three different spherical particles (made of plastic, glass and steel and three flow behavior index n, in three sets of power-law non-Newtonian fluids was investigated, based on polynomial solution (CM. Analytical results obtained indicated that the time of reaching the terminal velocity in a falling procedure is significantly increased with growing of the particle size that validated with Numerical Method. Further, with approaching flow behavior to Newtonian behavior from shear-thinning properties of flow (n → 1, the transient time to achieving the terminal settling velocity is decreased.

Comparative study of radiometric and calorimetric methods for total hemispherical emissivity measurements

Science.gov (United States)

Monchau, Jean-Pierre; Hameury, Jacques; Ausset, Patrick; Hay, Bruno; Ibos, Laurent; Candau, Yves

2018-05-01

Accurate knowledge of infrared emissivity is important in applications such as surface temperature measurements by infrared thermography or thermal balance for building walls. A comparison of total hemispherical emissivity measurement was performed by two laboratories: the Laboratoire National de Métrologie et d'Essais (LNE) and the Centre d'Études et de Recherche en Thermique, Environnement et Systèmes (CERTES). Both laboratories performed emissivity measurements on four samples, chosen to cover a large range of emissivity values and angular reflectance behaviors. The samples were polished aluminum (highly specular, low emissivity), bulk PVC (slightly specular, high emissivity), sandblasted aluminum (diffuse surface, medium emissivity), and aluminum paint (slightly specular surface, medium emissivity). Results obtained using five measurement techniques were compared. LNE used a calorimetric method for direct total hemispherical emissivity measurement [1], an absolute reflectometric measurement method [2], and a relative reflectometric measurement method. CERTES used two total hemispherical directional reflectometric measurement methods [3, 4]. For indirect techniques by reflectance measurements, the total hemispherical emissivity values were calculated from directional hemispherical reflectance measurement results using spectral integration when required and directional to hemispherical extrapolation. Results were compared, taking into account measurement uncertainties; an added uncertainty was introduced to account for heterogeneity over the surfaces of the samples and between samples. All techniques gave large relative uncertainties for a low emissive and very specular material (polished aluminum), and results were quite scattered. All the indirect techniques by reflectance measurement gave results within ±0.01 for a high emissivity material. A commercial aluminum paint appears to be a good candidate for producing samples with medium level of emissivity

An evaluation of passive methods for measurement of radon in dwellings

International Nuclear Information System (INIS)

Strand, T.; Lind, B.; Kolstad, A.K.

1989-01-01

During the last ten years, different methods have been developed for the measurement of radon in indoor air. In this report the different methods in use by private firms in Norway have been compared. The results of the study show that the methods are quite different in regard to integration time, detection limit and reliability in measurements of radon in indoor air. In 1988 the National Institute of Radiation Hygiene gave directives on the performance of such measurements. In these directives, minimum limits have been set for integration time (7 days) for methods to be used in evaluations of remedial actions. In this report the results from a simple, anonymeous reliability test are reported. The test covered the private firms offering radon meassurement services in Norway. The frequently reported weaknesses by the charcoal method were confirmed in the study. The directives on radon measurements in dwellings are presented. 73 refs.; 11 figs.; 5 tabs

Development of dose assessment method for high-energy neutrons using intelligent neutron monitor

International Nuclear Information System (INIS)

Satoh, Daiki; Sato, Tatsuhiko; Endo, Akira; Yamaguchi, Yasuhiro; Matsufuji, N.; Sato, S.; Takada, M.

2006-01-01

Light output of liquid organic scintillator NE213 has been measured for proton, deuteron, triton, 3 He nucleus and alpha particle. A thick graphite target was bombarded with 400-MeV/u C ions to the produce charged particles. Time-of-flight method was adopted to determine the kinetic energy of the charged particles. Light output for proton was also measured using mono-energy beams of 100 and 160 MeV. The experimental results gave a new database of light output. (author)

THE RELATIONSHIP BETWEEN LEARNING OUTCOMES ENTREPRENEURSHIP AND LEARNING OUTCOMES VOCATIONAL AUTOMOTIVE INTEREST STUDENT WORK CLASS X IN SMK MUHAMMADIYAH KARANGMOJO

Directory of Open Access Journals (Sweden)

Al Hashmy Hardhiansyah

2016-12-01

Full Text Available The study aimed to describe (1 correlation between automotive vocational learning with working interest; (2 correlation between entrepreneurship learning achievement with working interest of welding subject; and (3 correlation between automotive vocationallearning and entrepreneurship learning achievement with students’ working interest. This study was ex-post facto research. Data collecting methods were questionnaires and documentation. Data analyzing methods used descriptive analysis, first and second hypothesis testing used partial correlation and third hypothesis testing used double regression. This study shows that (1 there was a positive and significant correlation between automotive vocationallearning with learning achievement with the score of r obs = 0,308 with the significant score 0.015 < 0.05; (2 there was a positive and significant correlation between entrepreneurship  learning achievement  with working interest among with the score of r obs = 0,493 with the significant score 0.015 < 0.05; and (3 there was a positive and significant correlation between automotive vocationallearning and entrepreneurship  learning achievement  with working interest  with the significant score 0.000 < 0.05. The score of determinant coefficient (R2 0.252, it means that automotive vocationallearning and entrepreneurship  learning achievement  gave a positive contribution 25.2% toward working interest, while 74.8 % was influenced by other factors that were not discussed in this study. The automotive vocationallearning gave contribution 12.08% toward students’ working interest and entrepreneurship learning achievement gave contribution 13.12% toward students’ working interest.

The historical significance of oak

Science.gov (United States)

J. V. Thirgood

1971-01-01

A brief history of the importance of oak in Europe, contrasting the methods used in France and Britain to propagate the species and manage the forests for continued productivity. The significance of oak as a strategic resource during the sailing-ship era is stressed, and mention is made of the early development of oak management in North America. The international...

Histological staining methods preparatory to laser capture microdissection significantly affect the integrity of the cellular RNA.

Science.gov (United States)

Wang, Hongyang; Owens, James D; Shih, Joanna H; Li, Ming-Chung; Bonner, Robert F; Mushinski, J Frederic

2006-04-27

Gene expression profiling by microarray analysis of cells enriched by laser capture microdissection (LCM) faces several technical challenges. Frozen sections yield higher quality RNA than paraffin-imbedded sections, but even with frozen sections, the staining methods used for histological identification of cells of interest could still damage the mRNA in the cells. To study the contribution of staining methods to degradation of results from gene expression profiling of LCM samples, we subjected pellets of the mouse plasma cell tumor cell line TEPC 1165 to direct RNA extraction and to parallel frozen sectioning for LCM and subsequent RNA extraction. We used microarray hybridization analysis to compare gene expression profiles of RNA from cell pellets with gene expression profiles of RNA from frozen sections that had been stained with hematoxylin and eosin (H&E), Nissl Stain (NS), and for immunofluorescence (IF) as well as with the plasma cell-revealing methyl green pyronin (MGP) stain. All RNAs were amplified with two rounds of T7-based in vitro transcription and analyzed by two-color expression analysis on 10-K cDNA microarrays. The MGP-stained samples showed the least introduction of mRNA loss, followed by H&E and immunofluorescence. Nissl staining was significantly more detrimental to gene expression profiles, presumably owing to an aqueous step in which RNA may have been damaged by endogenous or exogenous RNAases. RNA damage can occur during the staining steps preparatory to laser capture microdissection, with the consequence of loss of representation of certain genes in microarray hybridization analysis. Inclusion of RNAase inhibitor in aqueous staining solutions appears to be important in protecting RNA from loss of gene transcripts.

A new and simple gravimetric method for determination of uranium

International Nuclear Information System (INIS)

Saxena, A.K.

1994-01-01

A new and simple gravimetric method for determining uranium has been described. Using a known quantity of uranyl nitrate as the test solution, an alcoholic solution of 2-amino-2-methyl 1:3 propanediol (AMP) was added slowly. A yellow precipitate was obtained which was filtered through ashless filter paper, washed with alcohol, dried and ignited at 800 degC for 4h. It gave a black powder as a product which was shown by X-ray diffraction to be U 3 O 8 . The percentage error was found in the range -0.09 to +0.89. (author). 8 refs., 1 tab

Significant Tsunami Events

Science.gov (United States)

Dunbar, P. K.; Furtney, M.; McLean, S. J.; Sweeney, A. D.

2014-12-01

Tsunamis have inflicted death and destruction on the coastlines of the world throughout history. The occurrence of tsunamis and the resulting effects have been collected and studied as far back as the second millennium B.C. The knowledge gained from cataloging and examining these events has led to significant changes in our understanding of tsunamis, tsunami sources, and methods to mitigate the effects of tsunamis. The most significant, not surprisingly, are often the most devastating, such as the 2011 Tohoku, Japan earthquake and tsunami. The goal of this poster is to give a brief overview of the occurrence of tsunamis and then focus specifically on several significant tsunamis. There are various criteria to determine the most significant tsunamis: the number of deaths, amount of damage, maximum runup height, had a major impact on tsunami science or policy, etc. As a result, descriptions will include some of the most costly (2011 Tohoku, Japan), the most deadly (2004 Sumatra, 1883 Krakatau), and the highest runup ever observed (1958 Lituya Bay, Alaska). The discovery of the Cascadia subduction zone as the source of the 1700 Japanese "Orphan" tsunami and a future tsunami threat to the U.S. northwest coast, contributed to the decision to form the U.S. National Tsunami Hazard Mitigation Program. The great Lisbon earthquake of 1755 marked the beginning of the modern era of seismology. Knowledge gained from the 1964 Alaska earthquake and tsunami helped confirm the theory of plate tectonics. The 1946 Alaska, 1952 Kuril Islands, 1960 Chile, 1964 Alaska, and the 2004 Banda Aceh, tsunamis all resulted in warning centers or systems being established.The data descriptions on this poster were extracted from NOAA's National Geophysical Data Center (NGDC) global historical tsunami database. Additional information about these tsunamis, as well as water level data can be found by accessing the NGDC website www.ngdc.noaa.gov/hazard/

Evaluation of the Thermo Scientific SureTect Listeria species assay. AOAC Performance Tested Method 071304.

Science.gov (United States)

Cloke, Jonathan; Evans, Katharine; Crabtree, David; Hughes, Annette; Simpson, Helen; Holopainen, Jani; Wickstrand, Nina; Kauppinen, Mikko; Leon-Velarde, Carlos; Larson, Nathan; Dave, Keron

2014-01-01

The Thermo Scientific SureTect Listeria species Assay is a new real-time PCR assay for the detection of all species of Listeria in food and environmental samples. This validation study was conducted using the AOAC Research Institute (RI) Performance Tested Methods program to validate the SureTect Listeria species Assay in comparison to the reference method detailed in International Organization for Standardization 11290-1:1996 including amendment 1:2004 in a variety of foods plus plastic and stainless steel. The food matrixes validated were smoked salmon, processed cheese, fresh bagged spinach, cantaloupe, cooked prawns, cooked sliced turkey meat, cooked sliced ham, salami, pork frankfurters, and raw ground beef. All matrixes were tested by Thermo Fisher Scientific, Microbiology Division, Basingstoke, UK. In addition, three matrixes (pork frankfurters, fresh bagged spinach, and stainless steel surface samples) were analyzed independently as part of the AOAC-RI-controlled independent laboratory study by the University ofGuelph, Canada. Using probability of detection statistical analysis, a significant difference in favour of the SureTect assay was demonstrated between the SureTect and reference method for high level spiked samples of pork frankfurters, smoked salmon, cooked prawns, stainless steel, and low-spiked samples of salami. For all other matrixes, no significant difference was seen between the two methods during the study. Inclusivity testing was conducted with 68 different isolates of Listeria species, all of which were detected by the SureTect Listeria species Assay. None of the 33 exclusivity isolates were detected by the SureTect Listeria species Assay. Ruggedness testing was conducted to evaluate the performance of the assay with specific method deviations outside of the recommended parameters open to variation, which demonstrated that the assay gave reliable performance. Accelerated stability testing was additionally conducted, validating the assay

A comparative study to investigate burnup in research reactor fuel using two independent experimental methods

International Nuclear Information System (INIS)

Iqbal, M.; Mehmood, T.; Ayazuddin, S.K.; Salahuddin, A.; Pervez, S.

2001-01-01

Two independent experimental methods have been used for the comparative study of fuel burnup measurement in low enriched uranium, plate type research reactor. In the first method a gamma ray activity ratio method was employed. An experimental setup was established for gamma ray scanning using prior calibrated high purity germanium detector. The computer software KORIGEN gave the theoretical support. In the second method reactivity difference technique was used. At the same location in the same core configuration the fresh and burned fuel element's reactivity worth was estimated. For theoretical estimated curve, group cross-sections were generated using computer code WIMS-D/4, and three dimensional modeling was made by computer code CITATION. The measured burnup of different fuel elements using these methods were found to be in good agreement

Comparison of three methods for detection of melamine in compost and soil

International Nuclear Information System (INIS)

Tian, Yongqiang; Chen, Liming; Gao, Lihong; Wu, Manli; Dick, Warren A.

2012-01-01

Recent product recalls and food safety incidents due to melamine (MM) adulteration or contamination have caused a worldwide food security concern. This has led to many methods being developed to detect MM in foods, but few methods haves been reported that can rapidly and reliably measure MM in environmental samples. To meet this need, a high performance liquid chromatography (HPLC) with UV detection method, an enzyme-linked immunosorbent assay (ELISA) test kit, and an enzyme-linked rapid colorimetric assay (RCA) test kit were evaluated for their ability to accurately measure MM concentrations in compost and soil samples. All three methods accurately detected MM concentrations if no MM degradation products, such as ammeline (AMN), ammelide (AMD) and cyanuric acid (CA), were present in an aqueous sample. In the presence of these MM degradation products, the HPLC yielded more accurate concentrations than the ELISA method and there was no significant (P > 0.05) difference between the HPLC and RCA methods. However, if samples were purified by SPE or prepared with blocking buffer, the ELISA method accurately measured MM concentrations, even in the presence of the MM degradation products. The HPLC method generally outperformed the RCA method for measuring MM in soil extracts but gave similar results for compost extracts. The number of samples that can be analyzed by the ELISA and RCA methods in a 24-hour time period is much greater than by the HPLC method. Thus the RCA method would seem to be a good screening method for measuring MM in compost and soil samples and the results obtained could then be confirmed by the HPLC method. The HPLC method, however, also allows simultaneous measurement of MM and its degradation products of AMD, AMN and CA. - Highlights: ► We detected melamine in environmental samples by three methods. ► ELISA can measures melamine in an environmental sample if a blocking buffer is used. ► A rapid colorimetric assay (RCA) rapidly screens

In Their Own Words: The Significance of Participant Perceptions in Assessing Entomology Citizen Science Learning Outcomes Using a Mixed Methods Approach.

Science.gov (United States)

Lynch, Louise I; Dauer, Jenny M; Babchuk, Wayne A; Heng-Moss, Tiffany; Golick, Doug

2018-02-06

A mixed methods study was used to transcend the traditional pre-, post-test approach of citizen science evaluative research by integrating adults' test scores with their perceptions. We assessed how contributory entomology citizen science affects participants' science self-efficacy, self-efficacy for environmental action, nature relatedness and attitude towards insects. Pre- and post-test score analyses from citizen scientists ( n = 28) and a control group ( n = 72) were coupled with interviews ( n = 11) about science experiences and entomological interactions during participation. Considering quantitative data alone, no statistically significant changes were evident in adults following participation in citizen science when compared to the control group. Citizen scientists' pre-test scores were significantly higher than the control group for self-efficacy for environmental action, nature relatedness and attitude towards insects. Interview data reveal a notable discrepancy between measured and perceived changes. In general, citizen scientists had an existing, long-term affinity for the natural world and perceived increases in their science self-efficacy, self-efficacy for environmental action, nature relatedness and attitude towards insects. Perceived influences may act independently of test scores. Scale instruments may not show impacts with variances in individual's prior knowledge and experiences. The value of mixed methods on citizen science program evaluation is discussed.

In Their Own Words: The Significance of Participant Perceptions in Assessing Entomology Citizen Science Learning Outcomes Using a Mixed Methods Approach

Science.gov (United States)

Lynch, Louise I.; Dauer, Jenny M.; Babchuk, Wayne A.; Heng-Moss, Tiffany

2018-01-01

A mixed methods study was used to transcend the traditional pre-, post-test approach of citizen science evaluative research by integrating adults’ test scores with their perceptions. We assessed how contributory entomology citizen science affects participants’ science self-efficacy, self-efficacy for environmental action, nature relatedness and attitude towards insects. Pre- and post-test score analyses from citizen scientists (n = 28) and a control group (n = 72) were coupled with interviews (n = 11) about science experiences and entomological interactions during participation. Considering quantitative data alone, no statistically significant changes were evident in adults following participation in citizen science when compared to the control group. Citizen scientists’ pre-test scores were significantly higher than the control group for self-efficacy for environmental action, nature relatedness and attitude towards insects. Interview data reveal a notable discrepancy between measured and perceived changes. In general, citizen scientists had an existing, long-term affinity for the natural world and perceived increases in their science self-efficacy, self-efficacy for environmental action, nature relatedness and attitude towards insects. Perceived influences may act independently of test scores. Scale instruments may not show impacts with variances in individual’s prior knowledge and experiences. The value of mixed methods on citizen science program evaluation is discussed. PMID:29415522

The Roche Immunoturbidimetric Albumin Method on Cobas c 501 Gives Higher Values Than the Abbott and Roche BCP Methods When Analyzing Patient Plasma Samples.

Science.gov (United States)

Helmersson-Karlqvist, Johanna; Flodin, Mats; Havelka, Aleksandra Mandic; Xu, Xiao Yan; Larsson, Anders

2016-09-01

Serum/plasma albumin is an important and widely used laboratory marker and it is important that we measure albumin correctly without bias. We had indications that the immunoturbidimetric method on Cobas c 501 and the bromocresol purple (BCP) method on Architect 16000 differed, so we decided to study these methods more closely. A total of 1,951 patient requests with albumin measured with both the Architect BCP and Cobas immunoturbidimetric methods were extracted from the laboratory system. A comparison with fresh plasma samples was also performed that included immunoturbidimetric and BCP methods on Cobas c 501 and analysis of the international protein calibrator ERM-DA470k/IFCC. The median difference between the Abbott BCP and Roche immunoturbidimetric methods was 3.3 g/l and the Roche method overestimated ERM-DA470k/IFCC by 2.2 g/l. The Roche immunoturbidimetric method gave higher values than the Roche BCP method: y = 1.111x - 0.739, R² = 0.971. The Roche immunoturbidimetric albumin method gives clearly higher values than the Abbott and Roche BCP methods when analyzing fresh patient samples. The differences between the two methods were similar at normal and low albumin levels. © 2016 Wiley Periodicals, Inc.

On exergy analysis of industrial plants and significance of ambient temperature

Energy Technology Data Exchange (ETDEWEB)

Rian, Berit

2011-07-01

the system gave an indication of whether the choice of environment would affect the exergy results or not. Furthermore, the additional study, where the effect on exergy results due to a fixed environmental state versus a natural environment was investigated, also suggested that neither calculations nor software tools should uncritically be based on the fixed environment when it does not correspond with the natural environment.The findings in these studies can be useful at different levels, such as for further studies and optimization of similar plants, for the authorities to encourage or demand even better performances from future plants and for developing methodical engineering tools for exergy.(au)

In vitro cost-effective methods to detect carbapenemases in Enterobacteriaceae

Directory of Open Access Journals (Sweden)

Varsha Gupta

2018-01-01

Full Text Available The rise in carbapenemases-producing organisms has challenged the scientific community. Infections caused by these bacteria have limited treatment options. There are various types such as Klebsiella pneumoniae carbapenemase (Ambler class A, metallo-beta-lactamases of VIM-type, IMP-type, NDM-type (Ambler class B, and OXA-48-types (Ambler class D. An efficient strategy for detection of carbapenemase producers is important to determine the appropriate therapeutic modalities. In this study, four methods - Carba NP test, modified Carba NP (MCNP test, carbapenem inactivation method (CIM test, and Rapidec Carba NP kit test were evaluated. We evaluated an in-house MCNP test to detect carbapenemase production using a single protocol which gave reliable results. Furthermore, CIM using routine antibiotic discs gives good results. Both these tests were found to be cost-effective.

Creep-fatigue evaluation method for type 304 and 316FR SS

International Nuclear Information System (INIS)

Wada, Y.; Aoto, K.; Ueno, F.

1997-01-01

For long-term creep-fatigue of Type 304SS, intergranular failure is dominant in the case of significant life reduction. It is considered that this phenomenon has its origin in the grain boundary sliding as observed in cavity-type creep-rupture. Accordingly a simplified procedure to estimate intergranular damages caused by the grain boundary sliding is presented in connection with the secondary creep. In the conventional ductility exhaustion method, failure ductility includes plastic strain, and damage estimation is based on the primary creep strain, which is recoverable during strain cycling. Therefore the accumulated creep strain becomes a very large value, and quite different from grain boundary sliding strain. As a new concept on ductility exhaustion, the product of secondary creep rate and time to rupture (Monkman-Grant product) is applied to fracture ductility, and grain boundary sliding strain is approximately estimated using the accumulated secondary creep strain. From the new concept it was shown that the time fraction rule and the conventional ductility exhaustion method can be derived analytically. Furthermore an advanced method on cyclic stress relaxation was examined. If cyclic plastic strain hardening is softened thermally during strain hold, cyclic creep strain behaviour is also softened. An unrecoverable accumulated primary creep strain causes hardening of the primary creep, and the reduction of deformation resistance to the secondary creep caused by thermal softening accelerates grain boundary sliding rate. As the results creep damages depend not on applied stress but on effective stress. The new concept ductility exhaustion method based on the above consideration leads up to simplified time fraction estimation method only by continuous cycling fatigue and monotonic creep which was already developed in PNC for Monju design guide. This method gave good life prediction for the intergranular failure mode and is convenient for design use on the elastic

Technical note: comparison of 3 methods for analyzing areas under the curve for glucose and nonesterified fatty acids concentrations following epinephrine challenge in dairy cows.

Science.gov (United States)

Cardoso, F C; Sears, W; LeBlanc, S J; Drackley, J K

2011-12-01

The objective of the study was to compare 3 methods for calculating the area under the curve (AUC) for plasma glucose and nonesterified fatty acids (NEFA) after an intravenous epinephrine (EPI) challenge in dairy cows. Cows were assigned to 1 of 6 dietary niacin treatments in a completely randomized 6 × 6 Latin square with an extra period to measure carryover effects. Periods consisted of a 7-d (d 1 to 7) adaptation period followed by a 7-d (d 8 to 14) measurement period. On d 12, cows received an i.v. infusion of EPI (1.4 μg/kg of BW). Blood was sampled at -45, -30, -20, -10, and -5 min before EPI infusion and 2.5, 5, 10, 15, 20, 30, 45, 60, 90, and 120 min after. The AUC was calculated by incremental area, positive incremental area, and total area using the trapezoidal rule. The 3 methods resulted in different statistical inferences. When comparing the 3 methods for NEFA and glucose response, no significant differences among treatments and no interactions between treatment and AUC method were observed. For glucose and NEFA response, the method was statistically significant. Our results suggest that the positive incremental method and the total area method gave similar results and interpretation but differed from the incremental area method. Furthermore, the 3 methods evaluated can lead to different results and statistical inferences for glucose and NEFA AUC after an EPI challenge. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Why do results conflict regarding the prognostic value of the methylation status in colon cancers? the role of the preservation method

Directory of Open Access Journals (Sweden)

Tournier Benjamin

2012-01-01

Full Text Available Abstract Background In colorectal carcinoma, extensive gene promoter hypermethylation is called the CpG island methylator phenotype (CIMP. Explaining why studies on CIMP and survival yield conflicting results is essential. Most experiments to measure DNA methylation rely on the sodium bisulfite conversion of unmethylated cytosines into uracils. No study has evaluated the performance of bisulfite conversion and methylation levels from matched cryo-preserved and Formalin-Fixed Paraffin Embedded (FFPE samples using pyrosequencing. Methods Couples of matched cryo-preserved and FFPE samples from 40 colon adenocarcinomas were analyzed. Rates of bisulfite conversion and levels of methylation of LINE-1, MLH1 and MGMT markers were measured. Results For the reproducibility of bisulfite conversion, the mean of bisulfite-to-bisulfite standard deviation (SD was 1.3%. The mean of run-to-run SD of PCR/pyrosequencing was 0.9%. Of the 40 DNA couples, only 67.5%, 55.0%, and 57.5% of FFPE DNA were interpretable for LINE-1, MLH1, and MGMT markers, respectively, after the first analysis. On frozen samples the proportion of well converted samples was 95.0%, 97.4% and 87.2% respectively. For DNA showing a total bisulfite conversion, 8 couples (27.6% for LINE-1, 4 couples (15.4% for MLH1 and 8 couples (25.8% for MGMT displayed significant differences in methylation levels. Conclusions Frozen samples gave reproducible results for bisulfite conversion and reliable methylation levels. FFPE samples gave unsatisfactory and non reproducible bisulfite conversions leading to random results for methylation levels. The use of FFPE collections to assess DNA methylation by bisulfite methods must not be recommended. This can partly explain the conflicting results on the prognosis of CIMP colon cancers.

Histological staining methods preparatory to laser capture microdissection significantly affect the integrity of the cellular RNA

Directory of Open Access Journals (Sweden)

Li Ming-Chung

2006-04-01

Full Text Available Abstract Background Gene expression profiling by microarray analysis of cells enriched by laser capture microdissection (LCM faces several technical challenges. Frozen sections yield higher quality RNA than paraffin-imbedded sections, but even with frozen sections, the staining methods used for histological identification of cells of interest could still damage the mRNA in the cells. To study the contribution of staining methods to degradation of results from gene expression profiling of LCM samples, we subjected pellets of the mouse plasma cell tumor cell line TEPC 1165 to direct RNA extraction and to parallel frozen sectioning for LCM and subsequent RNA extraction. We used microarray hybridization analysis to compare gene expression profiles of RNA from cell pellets with gene expression profiles of RNA from frozen sections that had been stained with hematoxylin and eosin (H&E, Nissl Stain (NS, and for immunofluorescence (IF as well as with the plasma cell-revealing methyl green pyronin (MGP stain. All RNAs were amplified with two rounds of T7-based in vitro transcription and analyzed by two-color expression analysis on 10-K cDNA microarrays. Results The MGP-stained samples showed the least introduction of mRNA loss, followed by H&E and immunofluorescence. Nissl staining was significantly more detrimental to gene expression profiles, presumably owing to an aqueous step in which RNA may have been damaged by endogenous or exogenous RNAases. Conclusion RNA damage can occur during the staining steps preparatory to laser capture microdissection, with the consequence of loss of representation of certain genes in microarray hybridization analysis. Inclusion of RNAase inhibitor in aqueous staining solutions appears to be important in protecting RNA from loss of gene transcripts.

ECRI audio conference focuses on RFID: the possible benefits are significant, but proceed slowly.

Science.gov (United States)

2005-07-01

This article highlights key points raised during ECRI's May 18, 2005, audio conference, "Radio-Frequency Identification (RFID) for Tracking Medical Devices: Planning for Today and Tomorrow." The conference gave attendees the opportunity to hear the experiences of two healthcare professionals managing RFID pilot programs at healthcare facilities. Information on ordering a recording of the event, including presentation materials and our recent Health Devices article on RFID, is provided at the end of this article.

Technology of irradiation of liquids by electron beams

International Nuclear Information System (INIS)

Tofaute, K.

1979-01-01

The methods of pretreatment, the technical details of the irradiating equipment, the applied radiation doses and the general requirements of the effectively working system are described. The extent of reinfection is compared in cases of heat-treated and electron-irradiated mud. The latter method gave significantly better results. (L.E.)

Estimation of boron, cadmium and cobalt at trace level in magnesium metal using ICP-AES method

International Nuclear Information System (INIS)

Patil, P.B.; Surya Prakash Rao, A.; Dixit, V.S.

2002-01-01

A method is established for the analysis of B, Cd and Co in the magnesium metal using ICP-AES technique in the range 1-50 ppm. Magnesium granules were dissolved in minimum amount of dilute nitric acid and the resultant solution is aspirated through ICP Nebulizer as nitrates Using various concentrations of matrix material 40, 20, 10 and 5 (mg/ml) were attempted to study the matrix effects on the above analytical elements. The optimum matrix concentration 20 mg/ml gave adequate detection limit of 1 ppm. The standard deviation of this method lies ∼ 1-3%. (author)

Significance levels for studies with correlated test statistics.

Science.gov (United States)

Shi, Jianxin; Levinson, Douglas F; Whittemore, Alice S

2008-07-01

When testing large numbers of null hypotheses, one needs to assess the evidence against the global null hypothesis that none of the hypotheses is false. Such evidence typically is based on the test statistic of the largest magnitude, whose statistical significance is evaluated by permuting the sample units to simulate its null distribution. Efron (2007) has noted that correlation among the test statistics can induce substantial interstudy variation in the shapes of their histograms, which may cause misleading tail counts. Here, we show that permutation-based estimates of the overall significance level also can be misleading when the test statistics are correlated. We propose that such estimates be conditioned on a simple measure of the spread of the observed histogram, and we provide a method for obtaining conditional significance levels. We justify this conditioning using the conditionality principle described by Cox and Hinkley (1974). Application of the method to gene expression data illustrates the circumstances when conditional significance levels are needed.

Significance of local cerebral glucose utilization determined by the autoradiographic (/sup 14/C)deoxyglucose method in experimentally induced coma

Energy Technology Data Exchange (ETDEWEB)

Sakurada, O.; Kobayashi, M.; Ueno, H.; Ishii, S. (Juntendo Univ., Tokyo (Japan). School of Medicine)

1982-01-01

Bilateral lesions made in the midbrain reticular formation of the rat produced behavioral akinesia. These animals neither ate nor drank. EEGs of these animals usually showed high voltage slow waves at rest. Slight EEG arousal response was demonstrated by clapping, touching and pinching only in rats with moderate impairment. Concerning the rates of local cerebral glucose utilization (LCGU) measured by means of the autoradiographic (/sup 14/C) deoxyglucose method, 13 structures exhibited significant reductions in 28 gray structures examined when compared with sham operated rats. Lesions in the midbrain reticular formation resulted in reduction of LCGU in the neocortex, ventral nucleus of the thalamus, subthalamic nucleus, and medial and lateral geniculated bodies, mamillary body, septal nucleus and caudateputamen. Structures which did not show any significant change in LCGU were those related to the paleo and archi-cortices. These findings suggest the existence of two types of ascending activating systems. Administration of 30 mg/kg of pentobarbital reduced LCGU diffusely throughout the brain. When thyrotropin releasing hormone (TRH) was administered to rats with lesions in the midbrain reticular formation, reversal of the reduction of LCGU was observed in the dorsomedial nucleus of the thalamus and the mamillary body. Reversal of LCGU in the dorsomedial nucleus of thalamus was especially significant and its level exceeded the level of the sham control value. This suggests TRH might exert its function through the dorsomedial nucleus of the thalamus and mamillary body. When TRH was administered to rats treated with pentobarbital, significant reversal was observed in the following structures: the lateral and ventral nucleus of the thalamus, dentate gyrus, caudate-putamen, nucleus accumbens, pontine gray matter, and raphe nucleus.

Significance of ultrasonography in selecting methods for the treatment of acute cholecystitis

Directory of Open Access Journals (Sweden)

Grzegorz Ćwik

2013-09-01

Full Text Available Surgical removal of the gallbladder is indicated in nearly all cases of complicated acute cholecystitis. In the 1990s, laparoscopic cholecystectomy became the method of choice in the treatment of cholecystolithiasis. Due to a large inflammatory reaction in the course of acute inflammation, a laparoscopic procedure is conducted in technically difficult conditions and entails the risk of complications. The aim of this paper was: 1 to analyze ultrasound images in acute cholecystitis; 2 to specify the most common causes of conversion from the laparoscopic method to open laparotomy; 3 to determine the degree to which the necessity for such a conversion may be predicted with the help of ultrasound examinations. Material and methods: In 1993–2011, in the Second Department and Clinic of General, Gastroenterological and Oncological Surgery of the Medical University in Lublin, 5,596 cholecystectomies were performed including 4,105 laparoscopic procedures that constituted 73.4% of all cholecystectomies. Five hundred and forty-two patients (13.2% were qualified for laparoscopic procedure despite manifesting typical symptoms of acute cholecystitis in ultrasound examination, which comprise: thickening of the gallbladder wall of > 3 mm, inflammatory infiltration in the Calot’s triangle region, gallbladder filled with stagnated or purulent contents and mural or intramural effusion. Results: In the group of operated patients, the conversion was necessary in 130 patients, i.e. in 24% of cases in comparison with 3.8% of patients with uncomplicated cholecystolithiasis (without the signs of inflammation. The conversion most frequently occurred when the assessment of the anatomical structures of the Calot’s triangle was rendered more difficult due to local inflammatory process, mural effusion and thickening of the gallbladder wall of >5 mm. The remaining changes occurred more rarely. Conclusions: Based on imaging scans, the most common causes of conversion

The significance of FM associations for women with FM.

Science.gov (United States)

Juuso, Päivi; Söderberg, Siv; Olsson, Malin; Skär, Lisa

2014-01-01

Living with fibromyalgia (FM) means living with a long-term pain syndrome that is invisible to others. Support and understanding from others seem to be important to managing the affected daily life. The aim of this study was to describe the significance of FM associations for women with FM. Data collection was carried out through focus group discussions with seventeen women with FM. Data were analyzed through thematic content analysis. The findings show that women experienced associations for people with FM as important as they gave access to contacts with others with similar experiences. Their need of togetherness was fulfilled at the association and they described being strengthened by the support received. Because of the lack of information and knowledge about FM, the association was described as an important venue for getting and mediating information about the illness. At the association the women seem to be empowered, which increases their ability to manage their daily lives despite the limitations imposed by FM. Healthcare personnel could not satisfy the women's needs and to manage to support women with FM. There is a need for communication based on a shared understanding between the women and healthcare personnel. This study highlighted the need for communication based on a shared understanding between people with chronic illness and healthcare personnel to support and strengthen women with FM in their daily lives. The FM associations meet the needs for togetherness, confirmation, and information that the women with FM in this study described and healthcare personnel could not satisfy. Healthcare personnel can learn from FM associations how to empower women with FM in their everyday lives.

Estimating HIES Data through Ratio and Regression Methods for Different Sampling Designs

Directory of Open Access Journals (Sweden)

Faqir Muhammad

2007-01-01

Full Text Available In this study, comparison has been made for different sampling designs, using the HIES data of North West Frontier Province (NWFP for 2001-02 and 1998-99 collected from the Federal Bureau of Statistics, Statistical Division, Government of Pakistan, Islamabad. The performance of the estimators has also been considered using bootstrap and Jacknife. A two-stage stratified random sample design is adopted by HIES. In the first stage, enumeration blocks and villages are treated as the first stage Primary Sampling Units (PSU. The sample PSU’s are selected with probability proportional to size. Secondary Sampling Units (SSU i.e., households are selected by systematic sampling with a random start. They have used a single study variable. We have compared the HIES technique with some other designs, which are: Stratified Simple Random Sampling. Stratified Systematic Sampling. Stratified Ranked Set Sampling. Stratified Two Phase Sampling. Ratio and Regression methods were applied with two study variables, which are: Income (y and Household sizes (x. Jacknife and Bootstrap are used for variance replication. Simple Random Sampling with sample size (462 to 561 gave moderate variances both by Jacknife and Bootstrap. By applying Systematic Sampling, we received moderate variance with sample size (467. In Jacknife with Systematic Sampling, we obtained variance of regression estimator greater than that of ratio estimator for a sample size (467 to 631. At a sample size (952 variance of ratio estimator gets greater than that of regression estimator. The most efficient design comes out to be Ranked set sampling compared with other designs. The Ranked set sampling with jackknife and bootstrap, gives minimum variance even with the smallest sample size (467. Two Phase sampling gave poor performance. Multi-stage sampling applied by HIES gave large variances especially if used with a single study variable.

INFLASI DAN TINGKAT BUNGA TERHADAP HARGA OBLIGASI NEGARA RITEL YANG DITERBITKAN PEMERINTAH

Directory of Open Access Journals (Sweden)

Asih Widajati

2017-03-01

Full Text Available The purpose of this research was to analyze the influence of the Inflation andinterest rate to bond price, and that research was important for obligation holder. The IndonesianGovernment Bonds used in this research were ORI 001, ORI 002, and ORI 003. The data wascollected from Indonesian Stock Exchange using documentation data collecting techniqueand data pooling. The analysis method used in this research was Path Analysis method. Theresult from t-test showed that statistically inflation did not significantly influence interest rateand SBI interest rate had significantly influenced bond price. The result of f-test inflation andinterest rate had significant effect to bond price at 50.60%. This research gave importantinformation for obligation holder even in stable economy. The increase of inflation rate andthe decrease of interest rate that were followed by the increase of bond price gave positiveinfluence to stock marketer especially for bond investor. For that purpose the bond holdershould keep the bond until it was due.

Detection of EGFR and COX-2 Expression by Immunohistochemical Method on a Tissue Microarray Section in Lung Cancer and Biological Significance

Directory of Open Access Journals (Sweden)

Xinyun WANG

2010-02-01

Full Text Available Background and objective Epidermal growth factor receptor (EGFR and cyclooxygenase-2 (COX-2, which can regulate growth, invasion and metastasis of tumor through relevant signaling pathway, have been detected in a variety of solid tumors. The aim of this study is to investigate the biological significance of EGFR and COX-2 expression in lung cancer and the relationship between them. Methods The expression of EGFR and COX-2 was detected in 89 primary lung cancer tissues, 12 premaliganant lesions, 12 lymph node metastases, and 10 normal lung tissues as the control by immunohistochemical method on a tissue microarray section. Results EGFR protein was detectable in 59.6%, 41.7%, and 66.7% of primary lung cancer tissues, premalignant lesions and lymph node metastases, respectively; COX-2 protein was detectable in 52.8%, 41.7%, and 66.7% of primary lung cancer tissues, premalignant lesions and lymph node metastases, respectively, which were significantly higher than those of the control (P 0.05. COX-2 expression was related to gross type (P < 0.05. A highly positive correlation was observed between EGFR and COX-2 expression (P < 0.01. Conclusion Overexpression of EGFR and COX-2 may play an important role in the tumorgenesis, progression and malignancy of lung cancer. Detection of EGFR and COX-2 expression might be helpful to diagnosis and prognosis of lung cancer.

Assay of serum ferritin by two different radioimmunometric methods and its clinical significance

International Nuclear Information System (INIS)

Kaltwasser, J.P.; Werner, E.; Gesellschaft fuer Strahlen- und Umweltforschung m.b.H., Frankfurt am Main

1977-01-01

Serum ferritin was measured by two different radioimmunometric methods a) the Addison assay, b) a commercial radioimmunoassay. Iron storage in the body was determined using 59 Fe. A dose correlation was found between serum ferritin and iron storage in the body. (AJ) [de

A simple and cost-effective method of DNA extraction from small formalin-fixed paraffin-embedded tissue for molecular oncologic testing.

Science.gov (United States)

Snow, Anthony N; Stence, Aaron A; Pruessner, Jonathan A; Bossler, Aaron D; Ma, Deqin

2014-01-01

Extraction of DNA from formalin-fixed, paraffin-embedded (FFPE) tissue is a critical step in molecular oncologic testing. As molecular oncology testing becomes more important for prognostic and therapeutic decision making and tissue specimens become smaller due to earlier detection of suspicious lesions and the use of fine needle aspiration methods for tissue collection, it becomes more challenging for the typical molecular pathology laboratory to obtain reliable test results. We developed a DNA extraction method to obtain sufficient quantity and high quality genomic DNA from limited FFPE tissue for molecular oncology testing using a combination of H&E stained slides, a matrix capture method and the Qiagen DNA column. THREE DNA EXTRACTION METHODS WERE COMPARED: our standard procedure of manually scraping tissue from unstained slides followed by DNA extraction using the QIAamp FFPE column (Qiagen, Valencia, CA), a glue capture method (Pinpoint Solution, Zymo Research Corp, Inc) on H&E stained slides followed by DNA extraction using either the QIAamp column or the column included with the Pinpoint kit (Zymo Research). The DNA extraction protocol was optimized. Statistical analysis was performed using the paired two-sample student's t-test. The combination of the matrix capture method with the QIAamp column gave an equivalent amount of DNA as our standard extraction method using the unstained slides and a 4.6-fold higher DNA yield than using the Zymo column included in the Pinpoint Slide Solution kit. Several molecular tests were performed and DNA purified using the new method gave the same results as for the previous methods. Using H&E stained slides allows visual confirmation of tumor cells during microdissection. The Pinpoint solution made removal of specific tissue from the slides easier and reduced the risk of contamination and tissue loss. This DNA extraction method is simple, cost-effective, and blends with our current workflow requiring no additional equipment.

A new multivariate empirical mode decomposition method for improving the performance of SSVEP-based brain-computer interface

Science.gov (United States)

Chen, Yi-Feng; Atal, Kiran; Xie, Sheng-Quan; Liu, Quan

2017-08-01

Objective. Accurate and efficient detection of steady-state visual evoked potentials (SSVEP) in electroencephalogram (EEG) is essential for the related brain-computer interface (BCI) applications. Approach. Although the canonical correlation analysis (CCA) has been applied extensively and successfully to SSVEP recognition, the spontaneous EEG activities and artifacts that often occur during data recording can deteriorate the recognition performance. Therefore, it is meaningful to extract a few frequency sub-bands of interest to avoid or reduce the influence of unrelated brain activity and artifacts. This paper presents an improved method to detect the frequency component associated with SSVEP using multivariate empirical mode decomposition (MEMD) and CCA (MEMD-CCA). EEG signals from nine healthy volunteers were recorded to evaluate the performance of the proposed method for SSVEP recognition. Main results. We compared our method with CCA and temporally local multivariate synchronization index (TMSI). The results suggest that the MEMD-CCA achieved significantly higher accuracy in contrast to standard CCA and TMSI. It gave the improvements of 1.34%, 3.11%, 3.33%, 10.45%, 15.78%, 18.45%, 15.00% and 14.22% on average over CCA at time windows from 0.5 s to 5 s and 0.55%, 1.56%, 7.78%, 14.67%, 13.67%, 7.33% and 7.78% over TMSI from 0.75 s to 5 s. The method outperformed the filter-based decomposition (FB), empirical mode decomposition (EMD) and wavelet decomposition (WT) based CCA for SSVEP recognition. Significance. The results demonstrate the ability of our proposed MEMD-CCA to improve the performance of SSVEP-based BCI.

Comparing two survey methods for estimating maternal and perinatal mortality in rural Cambodia.

Science.gov (United States)

Chandy, Hoeuy; Heng, Yang Van; Samol, Ha; Husum, Hans

2008-03-01

We need solid estimates of maternal mortality rates (MMR) to monitor the impact of maternal care programs. Cambodian health authorities and WHO report the MMR in Cambodia at 450 per 100,000 live births. The figure is drawn from surveys where information is obtained by interviewing respondents about the survival of all their adult sisters (sisterhood method). The estimate is statistically imprecise, 95% confidence intervals ranging from 260 to 620/100,000. The MMR estimate is also uncertain due to under-reporting; where 80-90% of women deliver at home maternal fatalities may go undetected especially where mortality is highest, in remote rural areas. The aim of this study was to attain more reliable MMR estimates by using survey methods other than the sisterhood method prior to an intervention targeting obstetric rural emergencies. The study was carried out in rural Northwestern Cambodia where access to health services is poor and poverty, endemic diseases, and land mines are endemic. Two survey methods were applied in two separate sectors: a community-based survey gathering data from public sources and a household survey gathering data direct from primary sources. There was no statistically significant difference between the two survey results for maternal deaths, both types of survey reported mortality rates around the public figure. The household survey reported a significantly higher perinatal mortality rate as compared to the community-based survey, 8.6% versus 5.0%. Also the household survey gave qualitative data important for a better understanding of the many problems faced by mothers giving birth in the remote villages. There are detection failures in both surveys; the failure rate may be as high as 30-40%. PRINCIPLE CONCLUSION: Both survey methods are inaccurate, therefore inappropriate for evaluation of short-term changes of mortality rates. Surveys based on primary informants yield qualitative information about mothers' hardships important for the design

Analysis of radioactive corrosion test specimens by means of ICP-MS. Comparison with earlier methods

International Nuclear Information System (INIS)

Forsyth, Roy

1997-07-01

In June 1992, an ICP-MS instrument (Inductively Coupled Plasma-Mass Spectrometry) was commissioned for use with radioactive sample solutions at Studsvik Nuclear's Hot Cell Laboratory. For conventional environmental samples the instrument permits the simultaneous analysis of many trace elements, but the software used in evaluation of the mass spectra is based on a library of isotopic compositions relevant only for elements in the lithosphere. Fission products and actinides, however, have isotopic compositions which are significantly different from the natural elements, and which also vary with the burnup of the nuclear fuel specimen. Consequently, a spread-sheet had to be developed which could evaluate the mass spectra with these isotopic compositions. Following these preparations, a large number of samples (about 200) from SKB's experimental programme for the study of spent fuel corrosion have been analyzed by the ICP-MS technique. Many of these samples were archive solutions of samples which had been taken earlier in the programme. This report presents a comparison of the analytical results for uranium, plutonium, cesium, strontium and technetium by both the ICP-MS technique, and the previously used analytical methods. For three products, a satisfactory agreement between the results from the various methods was obtained, but for uranium and plutonium the ICP-MS method gave results which were 10-20% higher than the conventional methods. The comparison programme has also shown, not unexpectedly, that significant losses of plutonium from solution had occurred, by precipitation and/or absorption, in the archive solutions during storage. It can be expected that such losses also occur for the other actinides, and consequently, all the analytical results for actinides in older archive solutions must be treated with great caution. 9 refs

Methods and techniques for obtaining significant discharge measurements on high-voltage bushings

Energy Technology Data Exchange (ETDEWEB)

Jolley, H E.W.

1965-05-01

Forms of discharge tests are described and compared. The use of the Arman and Starr discharge bridge with cathode-ray-tube display is shown to be practicable for bushing testing up to 600 kV. Spurious discharge effects and the precautions necessary to eliminate them are discussed. Consideration is given to calibration methods and to the errors to be expected with various practical circuits. The problem of establishing safe discharge limits for bushings is considered on the basis of a large number of test results and on service experience.

Efficiency of solvent extraction methods for the determination of methyl mercury in forest soils

Energy Technology Data Exchange (ETDEWEB)

Qian, J. [Department of Forest Ecology, Swedish University of Agricultural Sciences, Umeaa (Sweden); Dept. of Analytical Chemistry, Umeaa Univ. (Sweden); Skyllberg, U. [Department of Forest Ecology, Swedish University of Agricultural Sciences, Umeaa (Sweden); Tu, Q.; Frech, W. [Dept. of Analytical Chemistry, Umeaa Univ. (Sweden); Bleam, W.F. [Dept. of Soil Science, University of Wisconsin, Madison, WI (United States)

2000-07-01

Methyl mercury was determined by gas chromatography, microwave induced plasma, atomic emission spectrometry (GC-MIP-AES) using two different methods. One was based on extraction of mercury species into toluene, pre-concentration by evaporation and butylation of methyl mercury with a Grignard reagent followed by determination. With the other, methyl mercury was extracted into dichloromethane and back extracted into water followed by in situ ethylation, collection of ethylated mercury species on Tenax and determination. The accuracy of the entire procedure based on butylation was validated for the individual steps involved in the method. Methyl mercury added to various types of soil samples showed an overall average recovery of 87.5%. Reduced recovery was only caused by losses of methyl mercury during extraction into toluene and during pre-concentration by evaporation. The extraction of methyl mercury added to the soil was therefore quantitative. Since it is not possible to directly determine the extraction efficiency of incipient methyl mercury, the extraction efficiency of total mercury with an acidified solution containing CuSO{sub 4} and KBr was compared with high-pressure microwave acid digestion. The solvent extraction efficiency was 93%. For the IAEA 356 sediment certified reference material, mercury was less efficiently extracted and determined methyl mercury concentrations were below the certified value. Incomplete extraction could be explained by the presence of a large part of inorganic sulfides, as determined by x-ray absorption near-edge structure spectroscopy (XANES). Analyses of sediment reference material CRM 580 gave results in agreement with the certified value. The butylation method gave a detection limit for methyl mercury of 0.1 ng g{sup -1}, calculated as three times the standard deviation for repeated analysis of soil samples. Lower values were obtained with the ethylation method. The precision, expressed as RSD for concentrations 20 times

APLIKASI Z-SCORE METHOD DALAM PEMBENTUKAN PORTOFOLIO

Directory of Open Access Journals (Sweden)

Deannes Isynuwardhana

2017-03-01

Full Text Available The problem that often occurs in forming portfolio was regarding the selection and weighting the stock wichhad to be included in portfolio. This study attempted to solve the problem by using a simple model, which wasexpected to be applied easily by investors. This was a descriptive research with quantitative approach, andused stocks that was categorized as “blue chip” in Indonesia’s stock exchange as a sample. Stock selectionprocess used Z-score method with 6 criteria. There were, price earning ratio, price to book value, debt to equityratio, gross profit margin, return on equity, and stock’s historical price. The weighting of each stock inportfolio was then calculated by were used Bodie, Kane, and Markus (2011 approach. The coefficient ofvariation, risk and return of the market used as benchmark to measure portfolio performance. The result showedthat portfolio which formed by Z-score method give higher return than the market. Although the portfolioprovided greater risk, but it was not comparable with the marker return that gave negative results in return.The result suggested that portfolio which was created using the Z-score method could be applied by investorsin Indonesia’s stock exchange.

Development of HPLC and UV spectrophotometric methods for the determination of ascorbic acid using hydroxypropyl-β-cyclodextrin and triethanolamine as photostabilizing agents

International Nuclear Information System (INIS)

Garnero, Claudia; Longhi, Marcela

2010-01-01

In this study, the effect of complex formation with triethanolamine (TEA) alone and in combination with hydroxypropyl-β-cyclodextrin (HP-β-CD) on the photostability of ascorbic acid was evaluated for exposure to artificial and diffuse daylight. The first-order rate constants for the photodegradation reactions were determined. The data obtained showed that these complexes strongly reduced the photodegradation process with an 11- and 35-fold increase in the photostability of ascorbic acid, depending of the ligand concentration and the irradiation source. The multicomponent complex gave a significantly better stabilization for exposure to light than TEA alone. Due to the fact that the complexation extended the exposure of ascorbic acid to light (without molecular changes), UV spectrophotometric and reversed phase high performance liquid chromatographic (HPLC) methods were developed for the quantitative determination of the vitamin in pure form and in pharmaceutical preparations. These methods were statistically validated, all the validation parameters were found to be within the acceptance range. These results demonstrate that the proposed methods are suitable for the quality control of ascorbic acid, providing simple, rapid, precise, accurate and convenient approaches for routine analysis of bulk drug and pharmaceutical formulations.

Stability indicating high performance thin layer chromatographic method for quantitation of venlafaxine in bulk and pharmaceutical dosage form

Directory of Open Access Journals (Sweden)

Sunil K Dubey

2015-01-01

Full Text Available Background: Venlafaxine (VEN is a phenethylamine bicyclic compound, chemically, 1-(2-[dimethyl amino]-1-[4-methoxy phenyl] ethyl cyclo-hexan-1ol hydrochloride. It is a antidepressant. It inhibits the reuptake of serotonin, nor adrenaline and dopamine to a lesser extent at the presynaptic membrane. Aim: A simple, rapid, precise, accurate, and economical high performance thin layer chromatographic (HPTLC method has been developed and validated for the determination of VEN both as a bulk drug and in formulation. Materials and Methods: The method uses aluminum plates precoated with silica gel 60 F254 as the stationary phase and dichloromethane:acetonitrile:N-hexane:triethylamine: 0.5:0.5:4:0.7 (v/v/v/v as mobile phase. Results: This system gave compact spots for VEN (R f = 0.46 ± 0.05. Forced degradation studies were done by subjecting VEN to acid and alkali hydrolysis, oxidation, and reduction. The peak of the degradation product was well resolved from that of the pure drug and had significant different R f values. Analysis of VEN was performed in the absorbance mode at 225 nm. The limit of detection and quantification were 12.48 and 37.81 ng/spot respectively. Conclusions: The developed method was validated and found to be simple, specific, accurate and precise and can be used for routine quality control analysis of VEN in bulk and pharmaceutical formulation.

Evaluating significance in linear mixed-effects models in R.

Science.gov (United States)

Luke, Steven G

2017-08-01

Mixed-effects models are being used ever more frequently in the analysis of experimental data. However, in the lme4 package in R the standards for evaluating significance of fixed effects in these models (i.e., obtaining p-values) are somewhat vague. There are good reasons for this, but as researchers who are using these models are required in many cases to report p-values, some method for evaluating the significance of the model output is needed. This paper reports the results of simulations showing that the two most common methods for evaluating significance, using likelihood ratio tests and applying the z distribution to the Wald t values from the model output (t-as-z), are somewhat anti-conservative, especially for smaller sample sizes. Other methods for evaluating significance, including parametric bootstrapping and the Kenward-Roger and Satterthwaite approximations for degrees of freedom, were also evaluated. The results of these simulations suggest that Type 1 error rates are closest to .05 when models are fitted using REML and p-values are derived using the Kenward-Roger or Satterthwaite approximations, as these approximations both produced acceptable Type 1 error rates even for smaller samples.

A Comparative Analysis of Methods in the Research of Bilingual Semantic Memory

Directory of Open Access Journals (Sweden)

Tanja Gulan

2016-11-01

Full Text Available The facts that cognitive functioning of the bilingual speakers is different from that of the monolinguals, and that there is a growing number of bilinguals motivated us to write this paper. Such knowledge sets requirements on researchers to include bilingualism as an important variable in their research, even if the bilingualism is not the primary topic of their interest. However, the main topic of this paper was concerned with the methodology and was pointed toward researchers who are new to this area, as well as to those who are more experienced and wish to improve their research in the field of bilingualism. Taken that there is an increase in a number of published papers dealing with the bilingualism, especially regarding the organization of bilingual mental lexicon, we felt the need to offer a review of the most often used research paradigms and findings from this area of research.  This paper consists of three major parts. In the first part, we briefly defined main concepts in the field of bilingualism research followed by a brief discussion on the most important research questions. In the second part of this paper, we gave a review of the most important methods that are used in order to answer the aforementioned research questions. The methods were evaluated with regard to the scope they could be used to answer research questions. Moreover, this paper offered further recommendations for adequate method selection. And finally, the third part of the paper referred to the key methodological factors which a researcher needs to take into account while conceptualizing research and designing the experiment. Also, we gave some recommendations for how to control or annul the effects of those factors on the dependent variable.

Critical Test of Some Computational Chemistry Methods for Prediction of Gas-Phase Acidities and Basicities.

Science.gov (United States)

Toomsalu, Eve; Koppel, Ilmar A; Burk, Peeter

2013-09-10

Gas-phase acidities and basicities were calculated for 64 neutral bases (covering the scale from 139.9 kcal/mol to 251.9 kcal/mol) and 53 neutral acids (covering the scale from 299.5 kcal/mol to 411.7 kcal/mol). The following methods were used: AM1, PM3, PM6, PDDG, G2, G2MP2, G3, G3MP2, G4, G4MP2, CBS-QB3, B1B95, B2PLYP, B2PLYPD, B3LYP, B3PW91, B97D, B98, BLYP, BMK, BP86, CAM-B3LYP, HSEh1PBE, M06, M062X, M06HF, M06L, mPW2PLYP, mPW2PLYPD, O3LYP, OLYP, PBE1PBE, PBEPBE, tHCTHhyb, TPSSh, VSXC, X3LYP. The addition of the Grimmes empirical dispersion correction (D) to B2PLYP and mPW2PLYP was evaluated, and it was found that adding this correction gave more-accurate results when considering acidities. Calculations with B3LYP, B97D, BLYP, B2PLYPD, and PBE1PBE methods were carried out with five basis sets (6-311G**, 6-311+G**, TZVP, cc-pVTZ, and aug-cc-pVTZ) to evaluate the effect of basis sets on the accuracy of calculations. It was found that the best basis sets when considering accuracy of results and needed time were 6-311+G** and TZVP. Among semiempirical methods AM1 had the best ability to reproduce experimental acidities and basicities (the mean absolute error (mae) was 7.3 kcal/mol). Among DFT methods the best method considering accuracy, robustness, and computation time was PBE1PBE/6-311+G** (mae = 2.7 kcal/mol). Four Gaussian-type methods (G2, G2MP2, G4, and G4MP2) gave similar results to each other (mae = 2.3 kcal/mol). Gaussian-type methods are quite accurate, but their downside is the relatively long computational time.

Multiparametric comparison of chromogenic-based culture methods used to assess the microbiological quality of drinking water and the mFC method combined with a molecular confirmation procedure.

Science.gov (United States)

Maheux, Andrée F; Dion-Dupont, Vanessa; Bisson, Marc-Antoine; Bouchard, Sébastien; Jubinville, Éric; Nkuranga, Martine; Rodrigue, Lynda; Bergeron, Michel G; Rodriguez, Manuel J

2015-03-01

MI agar and Colilert(®), as well as mFC agar combined with an Escherichia coli-specific molecular assay (mFC + E. coli rtPCR), were compared in terms of their sensitivity, ease of use, time to result and affordability. The three methods yielded a positive E. coli signal for 11.5, 10.8, and 11.5% of the 968 well water samples tested, respectively. One hundred and thirty-six (136) samples gave blue colonies on mFC agar and required confirmation. E. coli-specific rtPCR showed false-positive results in 23.5% (32/136) of cases. In terms of ease of use, Colilert was the simplest method to use while the MI method provided ease of use comparable to all membrane filtration methods. However, the mFC + E. coli rtPCR assay required highly trained employees for confirmation purposes. In terms of affordability, and considering contamination rate of well water samples tested, the Colilert method and the mFC + E. coli rtPCR assay were at least five times more costly than the MI agar method. Overall, compared with the other two methods tested, the MI agar method offers the most advantages to assess drinking water quality.

Application of supersonic linear theory and hypersonic impact methods to three nonslender hypersonic airplane concepts at Mach numbers from 1.10 to 2.86

Science.gov (United States)

Pittman, J. L.

1979-01-01

Aerodynamic predictions from supersonic linear theory and hypersonic impact theory were compared with experimental data for three hypersonic research airplane concepts over a Mach number range from 1.10 to 2.86. The linear theory gave good lift prediction and fair to good pitching-moment prediction over the Mach number (M) range. The tangent-cone theory predictions were good for lift and fair to good for pitching moment for M more than or equal to 2.0. The combined tangent-cone theory predictions were good for lift and fair to good for pitching moment for M more than or equal to 2.0. The combined tangent-cone/tangent-wedge method gave the least accurate prediction of lift and pitching moment. The zero-lift drag was overestimated, especially for M less than 2.0. The linear theory drag prediction was generally poor, with areas of good agreement only for M less than or equal to 1.2. For M more than or equal to 2.), the tangent-cone method predicted the zero-lift drag most accurately.

Effect of heating method on stress-rupture life

Science.gov (United States)

Bizon, P. T.; Calfo, F. D.

1977-01-01

The effect of radiant(furnace), resistance(electric current), burner(hot gas stream), and a combination of resistance and burner heating on intermediate time (100 to 300 hr) stress-rupture life and reduction of area was evaluated. All heating methods were studied using the nickel-based alloy Udimet 700 while all but burner heating were evaluated with the cobalt-based alloy Mar-M 509. Limited test results of eight other superalloys were also included in this study. Resistance heated specimens had about 20 to 30 percent of the stress-rupture life of radiant heated specimens. The limited burner heating data showed about a 50 percent life reduction as compared to the radiant heated tests. A metallurgical examination gave no explanation for these reductions.

Data preprocessing methods of FT-NIR spectral data for the classification cooking oil

Science.gov (United States)

Ruah, Mas Ezatul Nadia Mohd; Rasaruddin, Nor Fazila; Fong, Sim Siong; Jaafar, Mohd Zuli

2014-12-01

This recent work describes the data pre-processing method of FT-NIR spectroscopy datasets of cooking oil and its quality parameters with chemometrics method. Pre-processing of near-infrared (NIR) spectral data has become an integral part of chemometrics modelling. Hence, this work is dedicated to investigate the utility and effectiveness of pre-processing algorithms namely row scaling, column scaling and single scaling process with Standard Normal Variate (SNV). The combinations of these scaling methods have impact on exploratory analysis and classification via Principle Component Analysis plot (PCA). The samples were divided into palm oil and non-palm cooking oil. The classification model was build using FT-NIR cooking oil spectra datasets in absorbance mode at the range of 4000cm-1-14000cm-1. Savitzky Golay derivative was applied before developing the classification model. Then, the data was separated into two sets which were training set and test set by using Duplex method. The number of each class was kept equal to 2/3 of the class that has the minimum number of sample. Then, the sample was employed t-statistic as variable selection method in order to select which variable is significant towards the classification models. The evaluation of data pre-processing were looking at value of modified silhouette width (mSW), PCA and also Percentage Correctly Classified (%CC). The results show that different data processing strategies resulting to substantial amount of model performances quality. The effects of several data pre-processing i.e. row scaling, column standardisation and single scaling process with Standard Normal Variate indicated by mSW and %CC. At two PCs model, all five classifier gave high %CC except Quadratic Distance Analysis.

A facile template method to synthesize significantly improved LiNi0.5Mn1.5O4 using corn stalk as a bio-template

International Nuclear Information System (INIS)

Liu, Guiyang; Kong, Xin; Sun, Hongyan; Wang, Baosen; Yi, Zhongzhou; Wang, Quanbiao

2014-01-01

In order to simplify the template method for the synthesis of cathode materials for lithium ion batteries, a facile template method using plant stalks as bio-templates has been introduced. Based on this method, LiNi 0.5 Mn 1.5 O 4 spinel with a significantly improved electrochemical performance has been synthesized using corn stalk as a template. X-ray diffraction (XRD), Fourier transform infrared pectroscopy (FTIR) and scanning electron microscope (SEM) have been used to investigate the phase composition and micro-morphologies of the products. Charge-discharge measurements in lithium cells, cyclic voltammetry (CV) and Electrochemical impedance spectroscopy (EIS) have been used to study the electrochemical performance of the products. The results indicate that the templated product exhibits higher crystallinity than that of non-templated product. Both of the templated product and the non-templated product are combination of the ordered space group P4 3 32 and the disordered Fd-3 m. The specific BET surface area of the templated product is about twice larger than that of the non-templated product. Moreover, the electrochemical performances of the templated product including specific capacity, cycling stability and rate capability are significantly improved as compared with the non-templated product, due to its higher crystallinity, larger Li + diffusion coefficient and lower charge transfer resistance

An Effective Vacuum Assisted Extraction Method for the Optimization of Labdane Diterpenoids from Andrographis paniculata by Response Surface Methodology

Directory of Open Access Journals (Sweden)

Ya-Qi Wang

2014-12-01

Full Text Available An effective vacuum assisted extraction (VAE technique was proposed for the first time and applied to extract bioactive components from Andrographis paniculata. The process was carefully optimized by response surface methodology (RSM. Under the optimized experimental conditions, the best results were obtained using a boiling temperature of 65 °C, 50% ethanol concentration, 16 min of extraction time, one extraction cycles and a 12:1 liquid-solid ratio. Compared with conventional ultrasonic assisted extraction and heat reflux extraction, the VAE technique gave shorter extraction times and remarkable higher extraction efficiency, which indicated that a certain degree of vacuum gave the solvent a better penetration of the solvent into the pores and between the matrix particles, and enhanced the process of mass transfer. The present results demonstrated that VAE is an efficient, simple and fast method for extracting bioactive components from A. paniculata, which shows great potential for becoming an alternative technique for industrial scale-up applications.

An effective vacuum assisted extraction method for the optimization of labdane diterpenoids from Andrographis paniculata by response surface methodology.

Science.gov (United States)

Wang, Ya-Qi; Wu, Zhen-Feng; Ke, Gang; Yang, Ming

2014-12-31

An effective vacuum assisted extraction (VAE) technique was proposed for the first time and applied to extract bioactive components from Andrographis paniculata. The process was carefully optimized by response surface methodology (RSM). Under the optimized experimental conditions, the best results were obtained using a boiling temperature of 65 °C, 50% ethanol concentration, 16 min of extraction time, one extraction cycles and a 12:1 liquid-solid ratio. Compared with conventional ultrasonic assisted extraction and heat reflux extraction, the VAE technique gave shorter extraction times and remarkable higher extraction efficiency, which indicated that a certain degree of vacuum gave the solvent a better penetration of the solvent into the pores and between the matrix particles, and enhanced the process of mass transfer. The present results demonstrated that VAE is an efficient, simple and fast method for extracting bioactive components from A. paniculata, which shows great potential for becoming an alternative technique for industrial scale-up applications.

Chemometric methods for the simultaneous determination of some water-soluble vitamins.

Science.gov (United States)

Mohamed, Abdel-Maaboud I; Mohamed, Horria A; Mohamed, Niveen A; El-Zahery, Marwa R

2011-01-01

Two spectrophotometric methods, derivative and multivariate methods, were applied for the determination of binary, ternary, and quaternary mixtures of the water-soluble vitamins thiamine HCI (I), pyridoxine HCI (II), riboflavin (III), and cyanocobalamin (IV). The first method is divided into first derivative and first derivative of ratio spectra methods, and the second into classical least squares and principal components regression methods. Both methods are based on spectrophotometric measurements of the studied vitamins in 0.1 M HCl solution in the range of 200-500 nm for all components. The linear calibration curves were obtained from 2.5-90 microg/mL, and the correlation coefficients ranged from 0.9991 to 0.9999. These methods were applied for the analysis of the following mixtures: (I) and (II); (I), (II), and (III); (I), (II), and (IV); and (I), (II), (III), and (IV). The described methods were successfully applied for the determination of vitamin combinations in synthetic mixtures and dosage forms from different manufacturers. The recovery ranged from 96.1 +/- 1.2 to 101.2 +/- 1.0% for derivative methods and 97.0 +/- 0.5 to 101.9 +/- 1.3% for multivariate methods. The results of the developed methods were compared with those of reported methods, and gave good accuracy and precision.

Dictionary Pruning with Visual Word Significance for Medical Image Retrieval.

Science.gov (United States)

Zhang, Fan; Song, Yang; Cai, Weidong; Hauptmann, Alexander G; Liu, Sidong; Pujol, Sonia; Kikinis, Ron; Fulham, Michael J; Feng, David Dagan; Chen, Mei

2016-02-12

Content-based medical image retrieval (CBMIR) is an active research area for disease diagnosis and treatment but it can be problematic given the small visual variations between anatomical structures. We propose a retrieval method based on a bag-of-visual-words (BoVW) to identify discriminative characteristics between different medical images with Pruned Dictionary based on Latent Semantic Topic description. We refer to this as the PD-LST retrieval. Our method has two main components. First, we calculate a topic-word significance value for each visual word given a certain latent topic to evaluate how the word is connected to this latent topic. The latent topics are learnt, based on the relationship between the images and words, and are employed to bridge the gap between low-level visual features and high-level semantics. These latent topics describe the images and words semantically and can thus facilitate more meaningful comparisons between the words. Second, we compute an overall-word significance value to evaluate the significance of a visual word within the entire dictionary. We designed an iterative ranking method to measure overall-word significance by considering the relationship between all latent topics and words. The words with higher values are considered meaningful with more significant discriminative power in differentiating medical images. We evaluated our method on two public medical imaging datasets and it showed improved retrieval accuracy and efficiency.

A comparative study of Averrhoabilimbi extraction method

Science.gov (United States)

Zulhaimi, H. I.; Rosli, I. R.; Kasim, K. F.; Akmal, H. Muhammad; Nuradibah, M. A.; Sam, S. T.

2017-09-01

In recent year, bioactive compound in plant has become a limelight in the food and pharmaceutical market, leading to research interest to implement effective technologies for extracting bioactive substance. Therefore, this study is focusing on extraction of Averrhoabilimbi by different extraction technique namely, maceration and ultrasound-assisted extraction. Fewplant partsof Averrhoabilimbiweretaken as extraction samples which are fruits, leaves and twig. Different solvents such as methanol, ethanol and distilled water were utilized in the process. Fruit extractsresult in highest extraction yield compared to other plant parts. Ethanol and distilled water have significant role compared to methanol in all parts and both extraction technique. The result also shows that ultrasound-assisted extraction gave comparable result with maceration. Besides, the shorter period on extraction process gives useful in term of implementation to industries.

The energetic significance of cooking.

Science.gov (United States)

Carmody, Rachel N; Wrangham, Richard W

2009-10-01

While cooking has long been argued to improve the diet, the nature of the improvement has not been well defined. As a result, the evolutionary significance of cooking has variously been proposed as being substantial or relatively trivial. In this paper, we evaluate the hypothesis that an important and consistent effect of cooking food is a rise in its net energy value. The pathways by which cooking influences net energy value differ for starch, protein, and lipid, and we therefore consider plant and animal foods separately. Evidence of compromised physiological performance among individuals on raw diets supports the hypothesis that cooked diets tend to provide energy. Mechanisms contributing to energy being gained from cooking include increased digestibility of starch and protein, reduced costs of digestion for cooked versus raw meat, and reduced energetic costs of detoxification and defence against pathogens. If cooking consistently improves the energetic value of foods through such mechanisms, its evolutionary impact depends partly on the relative energetic benefits of non-thermal processing methods used prior to cooking. We suggest that if non-thermal processing methods such as pounding were used by Lower Palaeolithic Homo, they likely provided an important increase in energy gain over unprocessed raw diets. However, cooking has critical effects not easily achievable by non-thermal processing, including the relatively complete gelatinisation of starch, efficient denaturing of proteins, and killing of food borne pathogens. This means that however sophisticated the non-thermal processing methods were, cooking would have conferred incremental energetic benefits. While much remains to be discovered, we conclude that the adoption of cooking would have led to an important rise in energy availability. For this reason, we predict that cooking had substantial evolutionary significance.

Comparing culture and molecular methods for the identification of microorganisms involved in necrotizing soft tissue infections

DEFF Research Database (Denmark)

Rudkjøbing, Vibeke Børsholt; Thomsen, Trine Rolighed; Xu, Yijuan

2016-01-01

BACKGROUND: Necrotizing soft tissue infections (NSTIs) are a group of infections affecting all soft tissues. NSTI involves necrosis of the afflicted tissue and is potentially life threatening due to major and rapid destruction of tissue, which often leads to septic shock and organ failure. The gold...... to culture. Although the molecular methods generally gave concordant results, our results indicate that Microseq may misidentify or overlook microorganisms that can be detected by other molecular methods. Half of the patients were found to be infected with S. pyogenes, but several atypical findings were also...... that clinicians should be prepared to diagnose and treat any combination of microbial pathogens. Some of the tested molecular methods offer a faster turnaround time combined with a high specificity, which makes supplemental use of such methods attractive for identification of microorganisms, especially...

Testing for significance of phase synchronisation dynamics in the EEG.

Science.gov (United States)

Daly, Ian; Sweeney-Reed, Catherine M; Nasuto, Slawomir J

2013-06-01

A number of tests exist to check for statistical significance of phase synchronisation within the Electroencephalogram (EEG); however, the majority suffer from a lack of generality and applicability. They may also fail to account for temporal dynamics in the phase synchronisation, regarding synchronisation as a constant state instead of a dynamical process. Therefore, a novel test is developed for identifying the statistical significance of phase synchronisation based upon a combination of work characterising temporal dynamics of multivariate time-series and Markov modelling. We show how this method is better able to assess the significance of phase synchronisation than a range of commonly used significance tests. We also show how the method may be applied to identify and classify significantly different phase synchronisation dynamics in both univariate and multivariate datasets.

Variability in CT lung-nodule volumetry: Effects of dose reduction and reconstruction methods.

Science.gov (United States)

Young, Stefano; Kim, Hyun J Grace; Ko, Moe Moe; Ko, War War; Flores, Carlos; McNitt-Gray, Michael F

2015-05-01

Measuring the size of nodules on chest CT is important for lung cancer staging and measuring therapy response. 3D volumetry has been proposed as a more robust alternative to 1D and 2D sizing methods. There have also been substantial advances in methods to reduce radiation dose in CT. The purpose of this work was to investigate the effect of dose reduction and reconstruction methods on variability in 3D lung-nodule volumetry. Reduced-dose CT scans were simulated by applying a noise-addition tool to the raw (sinogram) data from clinically indicated patient scans acquired on a multidetector-row CT scanner (Definition Flash, Siemens Healthcare). Scans were simulated at 25%, 10%, and 3% of the dose of their clinical protocol (CTDIvol of 20.9 mGy), corresponding to CTDIvol values of 5.2, 2.1, and 0.6 mGy. Simulated reduced-dose data were reconstructed with both conventional filtered backprojection (B45 kernel) and iterative reconstruction methods (SAFIRE: I44 strength 3 and I50 strength 3). Three lab technologist readers contoured "measurable" nodules in 33 patients under each of the different acquisition/reconstruction conditions in a blinded study design. Of the 33 measurable nodules, 17 were used to estimate repeatability with their clinical reference protocol, as well as interdose and inter-reconstruction-method reproducibilities. The authors compared the resulting distributions of proportional differences across dose and reconstruction methods by analyzing their means, standard deviations (SDs), and t-test and F-test results. The clinical-dose repeatability experiment yielded a mean proportional difference of 1.1% and SD of 5.5%. The interdose reproducibility experiments gave mean differences ranging from -5.6% to -1.7% and SDs ranging from 6.3% to 9.9%. The inter-reconstruction-method reproducibility experiments gave mean differences of 2.0% (I44 strength 3) and -0.3% (I50 strength 3), and SDs were identical at 7.3%. For the subset of repeatability cases, inter-reconstruction-method

Finding an optimal method for imaging lymphatic vessels of the upper limb

International Nuclear Information System (INIS)

O'Mahony, Susan; Purushotham, Arnie D.; Rose, Sarah L.; Chilvers, Alison J.; Ballinger, James R.; Solanki, Chandra K.; Barber, Robert W.; Peters, A. Michael; Mortimer, Peter S.

2004-01-01

Lymphoscintigraphy involves interstitial injection of radiolabelled particulate materials or radioproteins. Although several variations in the technique have been described, their place in clinical practice remains controversial. Traditional diagnostic criteria are based primarily on lymph node appearances but in situations such as breast cancer, where lymph nodes may have been excised, these criteria are of limited use. In these circumstances, lymphatic vessel morphology takes on greater importance as a clinical endpoint, so a method that gives good definition of lymphatic vessels would be useful. In patients with breast cancer, for example, such a method, used before and after lymph node resection, may assist in predicting the development of breast cancer-related lymphoedema. The aim of this study was to optimise a method for the visualisation of lymphatic vessels. Subcutaneous (sc) and intradermal (id) injection sites were compared, and technetium-99m nanocolloid, a particulate material, was compared with 99m Tc-human immunoglobulin (HIG), which is a soluble macromolecule. Twelve normal volunteers were each studied on two occasions. In three subjects, id 99m Tc-HIG was compared with sc 99m Tc-HIG, in three id 99m Tc-nanocolloid was compared with sc 99m Tc-nanocolloid, in three id 99m Tc-HIG was compared with id 99m Tc-nanocolloid and in three sc 99m Tc-HIG was compared with sc 99m Tc-nanocolloid. Endpoints were quality of lymphatic vessel definition, the time after injection at which vessels were most clearly visualised, the rate constant of depot disappearance (k) and the systemic blood accumulation rate as measured by gamma camera imaging over the liver or cardiac blood pool. Excellent definition of lymphatic vessels was obtained following id injection of either radiopharmaceutical, an injection route that was clearly superior to sc. Differences between radiopharmaceuticals were less clear, although after id injection, 99m Tc-HIG gave images that were

Combining Novel Simulation Methods and Nucleation Theory to Uncover the Secrets of Gas Hydrates

Energy Technology Data Exchange (ETDEWEB)

Keyes, Thomas [Boston Univ., MA (United States). Dept. of Chemistry

2016-04-14

Conventional computer simulation methods fail for some of the most important problems. With the design and application of innovative algorithms, this project achieved a breakthrough for the case of systems undergoing first-order phase transitions. We gave a complete simulation protocol based upon a well optimized version of our "generalized replica exchange method". The transition of primary interest was gas hydrate formation, a process of significance for climate science and natural gas retrieval. Since hydrates consist of guest molecules in the cages of a water matrix, β ice, the freezing and melting of water was also studied. New information was uncovered about the transition pathways and thermodynamics. Some highlights are 1. the finding that in a very dilute solution without deep supercooling, representative of real-world conditions and very challenging to conventional algorithms, methane can act as a catalyst to drive the formation of large amounts of β ice with empty cages as metastable intermediates, which might be filled by additional methane in a mechanism for hydrate formation, and 2. illumination of the role of metastable cubic ice in water freezing, with determination of the surface tensions of the cubic, hexagonal, and β ices, and the free energy difference of cubic vs hexagonal ice. Work was begun on lipid systems, bilayers and nanoreactors promising for energy-related photoreductions, and targets for future research. Our methods yielded what is arguably the most complete description of the composite lipid/water phases and the transition pathways among them.

Further Validation of a Rapid Screening Semiquantitative Thin-Layer Chromatographic Method for Marketed Antimalarial Medicines for Adoption in Malawi

Directory of Open Access Journals (Sweden)

Dorcas Osei-Safo

2018-01-01

Full Text Available A recently developed semiquantitative thin-layer chromatographic (SQ-TLC assay has been employed in postmarketing surveillance of antimalarial medicines used in Malawi prior to HPLC assay. Both methods gave analogous results in a significant majority of the samples, with a good correlation (r = 0.9012 for the active pharmaceutical ingredients of the dosage forms assayed. Artemether-containing medicines had the highest percentage (92.67% of samples with comparable results for both assays. The lowest percentage (66.67% was observed in artesunate-containing medicines. The SQ-TLC method was validated for specificity, accuracy, precision, linearity, and stability according to the International Conference on Harmonisation guidelines, with the results falling within acceptable limits. For specificity, retention factor values of the test samples and reference standards were comparable, while accuracy and precision of 91.1 ± 5.7% were obtained for all samples. The method was linear in the range 1.0–2.0 µg/spot with a correlation coefficient of r = 0.9783. Stability tests also fell within acceptable limits. In this study, we present the validation of the SQ-TLC method and propose its adoption as a rapid screening tool for field estimation of the quality of antimalarial and other essential medicines in Malawi and other parts of the developing world prior to a more accurate HPLC assay.

Simplified pressure method for respirator fit testing.

Science.gov (United States)

Han, D; Xu, M; Foo, S; Pilacinski, W; Willeke, K

1991-08-01

A simplified pressure method has been developed for fit testing air-purifying respirators. In this method, the air-purifying cartridges are replaced by a pressure-sensing attachment and a valve. While wearers hold their breath, a small pump extracts air from the respirator cavity until a steady-state pressure is reached in 1 to 2 sec. The flow rate through the face seal leak is a unique function of this pressure, which is determined once for all respirators, regardless of the respirator's cavity volume or deformation because of pliability. The contaminant concentration inside the respirator depends on the degree of dilution by the flow through the cartridges. The cartridge flow varies among different brands and is measured once for each brand. The ratio of cartridge to leakflow is a measure of fit. This flow ratio has been measured on human subjects and has been compared to fit factors determined on the same subjects by means of photometric and particle count tests. The aerosol tests gave higher values of fit.

Treatment of Petroleum Sludge By Using Solidification/Stabilization (S/S) Method : Effect of Hydration Days to Heavy Metals Leaching and Strength

Science.gov (United States)

Murshid, N.; Kamil, N. A. F. M.; Kadir, A. A.

2018-04-01

Petroleum sludge is one of the major solid wastes generated in the petroleum industry. Generally, there are numbers of heavy metals in petroleum sludge and one treatment that is gaining prominence to treat a variety of mixed organic and inorganic waste is solidification/stabilization (S/S) method. The treatment protects human health and the environment by immobilizing contaminants within the treated material and prevents migration of the contaminants. In this study, solidification/stabilization (S/S) method has been used to treat the petroleum sludge. The comparison of hydration days, namely, 7th and 28th days in these cement-based waste materials were studied by using Synthetic Precipitate Leaching Procedure (SPLP). The results were compared to the United States Environmental Protection Agency (USEPA) standards. The results for leaching test concluded that less percentage OPC gave maximum concentration of heavy metals leaching due to deficient in Calcium Oxide (CaO), which is can caused weak solidification in the mixture. Physical and mechanical properties conducted such as compressive strength and density test. From the results, it shows addition up to of 30percentage PS give results which comply with minimum landfill dispose limit. The results shows correlation between strength and density are strong regression coefficient of 82.7%. In conclusion, S/S method can be alternative disposal method for PS in the same time complies with standard for minimum landfill disposal limit. The results for leaching test concluded the less OPC percentage gave maximum concentration of heavy metals leaching.

The use of stir bar sorptive extraction-A potential alternative method for the determination of furan, evaluated using two example food matrices

Energy Technology Data Exchange (ETDEWEB)

Ridgway, Kathy, E-mail: Kathy.Ridgway@Unilever.com [Safety and Environmental Assurance Centre, Unilever Colworth, Bedfordshire, MK44 1LQ (United Kingdom); Lalljie, Sam P.D. [Safety and Environmental Assurance Centre, Unilever Colworth, Bedfordshire, MK44 1LQ (United Kingdom); Smith, Roger M. [Department of Chemistry, Loughborough University, Loughborough, Leics, LE11 3TU (United Kingdom)

2010-01-11

A comparison is made between static headspace analysis and stir bar sorptive extraction (SBSE) for the quantitative determination of furan. The SBSE technique was optimised and evaluated using two example food matrices (coffee and jarred baby food). The use of the SBSE technique in most cases, gave comparable results to the static headspace method, using the method of standard additions with d{sub 4}-labelled furan as an internal standard. Using the SBSE method, limits of detection down to 2 ng g{sup -1} were achieved, with only a 1 h extraction. The method was performed at ambient temperatures, thus eliminating the possibility of formation of furan during extraction.

The use of stir bar sorptive extraction-A potential alternative method for the determination of furan, evaluated using two example food matrices

International Nuclear Information System (INIS)

Ridgway, Kathy; Lalljie, Sam P.D.; Smith, Roger M.

2010-01-01

A comparison is made between static headspace analysis and stir bar sorptive extraction (SBSE) for the quantitative determination of furan. The SBSE technique was optimised and evaluated using two example food matrices (coffee and jarred baby food). The use of the SBSE technique in most cases, gave comparable results to the static headspace method, using the method of standard additions with d 4 -labelled furan as an internal standard. Using the SBSE method, limits of detection down to 2 ng g -1 were achieved, with only a 1 h extraction. The method was performed at ambient temperatures, thus eliminating the possibility of formation of furan during extraction.

Active Learning with Rationales for Identifying Operationally Significant Anomalies in Aviation

Science.gov (United States)

Sharma, Manali; Das, Kamalika; Bilgic, Mustafa; Matthews, Bryan; Nielsen, David Lynn; Oza, Nikunj C.

2016-01-01

A major focus of the commercial aviation community is discovery of unknown safety events in flight operations data. Data-driven unsupervised anomaly detection methods are better at capturing unknown safety events compared to rule-based methods which only look for known violations. However, not all statistical anomalies that are discovered by these unsupervised anomaly detection methods are operationally significant (e.g., represent a safety concern). Subject Matter Experts (SMEs) have to spend significant time reviewing these statistical anomalies individually to identify a few operationally significant ones. In this paper we propose an active learning algorithm that incorporates SME feedback in the form of rationales to build a classifier that can distinguish between uninteresting and operationally significant anomalies. Experimental evaluation on real aviation data shows that our approach improves detection of operationally significant events by as much as 75% compared to the state-of-the-art. The learnt classifier also generalizes well to additional validation data sets.

The Daily as a mixture of media and a new significance through the newspaper

Directory of Open Access Journals (Sweden)

Eduardo Campos Pellanda

2013-09-01

Full Text Available Materiality (support, languages and editing gave an identity toeach type of journalism, generating formats such as: newspaper, magazine, TV journalism, radio journalism and so on. The analysis of the digital newspaper The Daily made us question to what extent this division is still relevant. The aim of this paper is to discuss The Daily as a representative of a new media experience and as a mixture of media, in what concerns materiality and languages, and also thinking about the own convergence culture.

The role and significance of Luo Zhiyuan's Shu yi hui bian in the history of plague in Lingnan (south of the five ridges).

Science.gov (United States)

Li, H; Lai, W

1999-04-01

Being the earliest monograph on plague in China, Luo Zhiyuan's Shu yi hui bian, not included in the National Catalogue of TCM Books, include the following contents: personal idea on the etiology of plague; Luo's friend Wu Xuanchang' unpublished Shu yu zhi fa on the treatment and manifestations of plague; Luo's specific recipe for plague based on medified Wang Qingren's Jie du huo xue decoction based on Wang Qingrens yi lin gai cuo; therapy for critical cases; many therapies applied on Lingnan, including experimental recipes, external therapy, preventive methods, and preventing recurrence methods; Luo's special administrating methods, including persisting day-and-night method, immediate persisting method, single-dose persisting method, and double-dose persisting method. He also gave several cured case records. His book, featuring unique idea with good effect, was repeatedly printed and extensively distributed, exerting influence, more or less, on the plague monographs of later ages, and occupying important position in the history of plague on Lingnan and the whole country as well. His idea of "that poisons and static blood" in pathogenesis and therapeutic principle of antitoxicity and activating blood is coincided with the results of present day clinical and laboratory studies. His administration of medicines is heuristic to the therapy of critical cases with Chinese medicaments and to the recognition of pathogenesis, etiology, and treatment of modern plague as well as other diseases of similar etiology and pathognesis and is worth of further study.

Towards an efficient protocol for the determination of triterpenic acids in olive fruit: a comparative study of drying and extraction methods.

Science.gov (United States)

Goulas, Vlasios; Manganaris, George A

2012-01-01

Triterpenic acids, such as maslinic acid and oleanolic acid, are commonly found in olive fruits and have been associated with many health benefits. The drying and extraction methods, as well as the solvents used, are critical factors in the determination of their concentration in plant tissues. Thus, there is an emerging need for standardisation of an efficient extraction protocol that determines triterpenic acid content in olive fruits. To evaluate common extraction methods of triterpenic acids from olive fruits and to determine the effect of the drying method on their content in order to propose an optimum protocol for their quantification. The efficacy of different drying and extraction methods was evaluated through the quantification of maslinic acid and oleanolic acid contents using the reversed-phase HPLC technique. Data showed that ultrasonic assisted extraction with ethanol or a mixture of ethanol:methanol (1:1, v/v) resulted in the recovery of significantly higher amounts of triterpenic acids than other methods used. The drying method also affected the estimated triterpenic acid content; frozen or lyophilised olive fruit material gave higher yields of triterpenic acids compared with air-dried material at both 35°C and 105°C. This study provides a rapid and low-cost extraction method, i.e. ultrasonic assisted extraction with an eco-friendly solvent such as ethanol, from frozen or lyophilised olive fruit for the accurate determination of the triterpenic acid content in olive fruit. Copyright © 2011 John Wiley & Sons, Ltd.

Microalbuminuria Measured by three Different Methods, Blood Pressure and Cardiovascular Risk Factors in Elderly Swedish Males

Directory of Open Access Journals (Sweden)

Gösta Florvall

2008-01-01

Full Text Available Microalbuminuria is associated with hypertension and is a strong risk factor for subsequent chronic disease, both renal and coronary heart disease (CHD, Presently there are several methods available for measurement of microalbuminuria. The aim of this study was to evaluate if the three different methods gave similar information or if one of the assays were superior to the others. Blood pressure, inflammatory markers and cardiovascular mortality and morbidity were correlated with urine albumin analysed with a point-of-care testing (POCT instrument, nephelometric determination of albumin and albumin/creatinine ratio in elderly males. The study population consisted of 103 diabetic and 603 nondiabetic males (age 77 years in a cross-sectional study. We analyzed urine albumin with a HemoCue® Urine Albumin POCT instrument and a ProSpec® nephelometer and albumin/creatinine ratio. There were strong correlations between both systolic and diastolic blood pressure and all three urine albumin methods (p < 0.0001. There were also significant correlations between the different urine albumin measurements and serum amyloid A component, high-sensitivity C-reactive protein and interleukin-6. The three different urine albumin methods studied provided similar information in relation to cardiovascular disease. There was a strong correlation between systolic and diastolic blood pressure and microalbuminuria in both the whole study population and in nondiabetic males emphasizing the role of hypertension in glomerular damage. The good correlation between the studied urine albumin measurements show that all three methods can be used for monitoring urine albumin excretion.

An attempt of 'out-tongue method' to reduce taste dysfunction following head and neck irradiation

International Nuclear Information System (INIS)

Miyashita, Tsuguhiro; Tateno, Atsushi; Kumashiro, Katsutoshi; Sasaki, Sadayuki; Kumazaki, Tatsuo; Ohno, Haruyoshi; Sato, Iisaku.

1996-01-01

To reduce taste dysfunction which lowers QOL of patients with head and neck carcinoma during and after radiation therapy, an 'out-tongue method' was attempted where patients put out their tongue during the irradiation. The attempt was done on 15 patients of the carcinoma, aging 42-83 years old. They received enough information and training of the method. The training was important for reproducibility. Irradiation with 35-61.2 (mean 52.9) Gy of the oral cavity was performed by linac with continuous monitoring for keeping the method. The volume of irradiated tongue was reduced to 1/3-2/3 level. The effect of the method was evaluated by 4-graded score: no change, fair (a small change in taste post radiation), moderate and severe (no taste). The method gave no change in 9 patients (60%), fair in 3 (20%), moderate in 3 (20%) and severe in 0 (0%). These results suggested that this method was useful. (K.H.)

Comparison of three methods for detection of melamine in compost and soil

Energy Technology Data Exchange (ETDEWEB)

Tian, Yongqiang [Depatment of Vegetable Science, College of Agronomy and Biotechnology, China Agricultural University, 2 Yuanmingyuan Xilu, Beijing 100193 (China); School of Environment and Natural Resources, The Ohio State University, 1680 Madison Avenue, Wooster, OH 44691 (United States); Chen, Liming [School of Environment and Natural Resources, The Ohio State University, 1680 Madison Avenue, Wooster, OH 44691 (United States); Gao, Lihong [Depatment of Vegetable Science, College of Agronomy and Biotechnology, China Agricultural University, 2 Yuanmingyuan Xilu, Beijing 100193 (China); Wu, Manli [School of Environment and Natural Resources, The Ohio State University, 1680 Madison Avenue, Wooster, OH 44691 (United States); School of Environmental and Municipal Engineering, Xi' an University of Architecture and Technology, No.13 Yanta Road, Xi' an, Shaanxi Province 710055 (China); Dick, Warren A., E-mail: dick.5@osu.edu [School of Environment and Natural Resources, The Ohio State University, 1680 Madison Avenue, Wooster, OH 44691 (United States)

2012-02-15

Recent product recalls and food safety incidents due to melamine (MM) adulteration or contamination have caused a worldwide food security concern. This has led to many methods being developed to detect MM in foods, but few methods haves been reported that can rapidly and reliably measure MM in environmental samples. To meet this need, a high performance liquid chromatography (HPLC) with UV detection method, an enzyme-linked immunosorbent assay (ELISA) test kit, and an enzyme-linked rapid colorimetric assay (RCA) test kit were evaluated for their ability to accurately measure MM concentrations in compost and soil samples. All three methods accurately detected MM concentrations if no MM degradation products, such as ammeline (AMN), ammelide (AMD) and cyanuric acid (CA), were present in an aqueous sample. In the presence of these MM degradation products, the HPLC yielded more accurate concentrations than the ELISA method and there was no significant (P > 0.05) difference between the HPLC and RCA methods. However, if samples were purified by SPE or prepared with blocking buffer, the ELISA method accurately measured MM concentrations, even in the presence of the MM degradation products. The HPLC method generally outperformed the RCA method for measuring MM in soil extracts but gave similar results for compost extracts. The number of samples that can be analyzed by the ELISA and RCA methods in a 24-hour time period is much greater than by the HPLC method. Thus the RCA method would seem to be a good screening method for measuring MM in compost and soil samples and the results obtained could then be confirmed by the HPLC method. The HPLC method, however, also allows simultaneous measurement of MM and its degradation products of AMD, AMN and CA. - Highlights: Black-Right-Pointing-Pointer We detected melamine in environmental samples by three methods. Black-Right-Pointing-Pointer ELISA can measures melamine in an environmental sample if a blocking buffer is used. Black

Chemical characteristics of fine particles emitted from different gas cooking methods

Science.gov (United States)

See, Siao Wei; Balasubramanian, Rajasekhar

Gas cooking is an important indoor source of fine particles (PM 2.5). The chemical characteristics of PM 2.5 emitted from different cooking methods, namely, steaming, boiling, stir-frying, pan-frying and deep-frying were investigated in a domestic kitchen. Controlled experiments were conducted to measure the mass concentration of PM 2.5 and its chemical constituents (elemental carbon (EC), organic carbon (OC), polycyclic aromatic hydrocarbons (PAHs), metals and ions) arising from these five cooking methods. To investigate the difference in particle properties of different cooking emissions, the amount and type of food, and the heat setting on the gas stove were kept constant during the entire course of the experiments. Results showed that deep-frying gave rise to the largest amount of PM 2.5 and most chemical components, followed by pan-frying, stir-frying, boiling, and steaming. Oil-based cooking methods released more organic pollutants (OC, PAHs, and organic ions) and metals, while water-based cooking methods accounted for more water-soluble (WS) ions. Their source profiles are also presented and discussed.

On detection and assessment of statistical significance of Genomic Islands

Directory of Open Access Journals (Sweden)

Chaudhuri Probal

2008-04-01

Full Text Available Abstract Background Many of the available methods for detecting Genomic Islands (GIs in prokaryotic genomes use markers such as transposons, proximal tRNAs, flanking repeats etc., or they use other supervised techniques requiring training datasets. Most of these methods are primarily based on the biases in GC content or codon and amino acid usage of the islands. However, these methods either do not use any formal statistical test of significance or use statistical tests for which the critical values and the P-values are not adequately justified. We propose a method, which is unsupervised in nature and uses Monte-Carlo statistical tests based on randomly selected segments of a chromosome. Such tests are supported by precise statistical distribution theory, and consequently, the resulting P-values are quite reliable for making the decision. Results Our algorithm (named Design-Island, an acronym for Detection of Statistically Significant Genomic Island runs in two phases. Some 'putative GIs' are identified in the first phase, and those are refined into smaller segments containing horizontally acquired genes in the refinement phase. This method is applied to Salmonella typhi CT18 genome leading to the discovery of several new pathogenicity, antibiotic resistance and metabolic islands that were missed by earlier methods. Many of these islands contain mobile genetic elements like phage-mediated genes, transposons, integrase and IS elements confirming their horizontal acquirement. Conclusion The proposed method is based on statistical tests supported by precise distribution theory and reliable P-values along with a technique for visualizing statistically significant islands. The performance of our method is better than many other well known methods in terms of their sensitivity and accuracy, and in terms of specificity, it is comparable to other methods.

On the computational assessment of white matter hyperintensity progression: difficulties in method selection and bias field correction performance on images with significant white matter pathology

Energy Technology Data Exchange (ETDEWEB)

Valdes Hernandez, Maria del C.; Gonzalez-Castro, Victor; Wang, Xin; Doubal, Fergus; Munoz Maniega, Susana; Wardlaw, Joanna M. [Centre for Clinical Brian Sciences, Department of Neuroimaging Sciences, Edinburgh (United Kingdom); Ghandour, Dina T. [University of Edinburgh, College of Medicine and Veterinary Medicine, Edinburgh (United Kingdom); Armitage, Paul A. [University of Sheffield, Department of Cardiovascular Sciences, Sheffield (United Kingdom)

2016-05-15

Subtle inhomogeneities in the scanner's magnetic fields (B{sub 0} and B{sub 1}) alter the intensity levels of the structural magnetic resonance imaging (MRI) affecting the volumetric assessment of WMH changes. Here, we investigate the influence that (1) correcting the images for the B{sub 1} inhomogeneities (i.e. bias field correction (BFC)) and (2) selection of the WMH change assessment method can have on longitudinal analyses of WMH progression and discuss possible solutions. We used brain structural MRI from 46 mild stroke patients scanned at stroke onset and 3 years later. We tested three BFC approaches: FSL-FAST, N4 and exponentially entropy-driven homomorphic unsharp masking (E{sup 2}D-HUM) and analysed their effect on the measured WMH change. Separately, we tested two methods to assess WMH changes: measuring WMH volumes independently at both time points semi-automatically (MCMxxxVI) and subtracting intensity-normalised FLAIR images at both time points following image gamma correction. We then combined the BFC with the computational method that performed best across the whole sample to assess WMH changes. Analysis of the difference in the variance-to-mean intensity ratio in normal tissue between BFC and uncorrected images and visual inspection showed that all BFC methods altered the WMH appearance and distribution, but FSL-FAST in general performed more consistently across the sample and MRI modalities. The WMH volume change over 3 years obtained with MCMxxxVI with vs. without FSL-FAST BFC did not significantly differ (medians(IQR)(with BFC) = 3.2(6.3) vs. 2.9(7.4)ml (without BFC), p = 0.5), but both differed significantly from the WMH volume change obtained from subtracting post-processed FLAIR images (without BFC)(7.6(8.2)ml, p < 0.001). This latter method considerably inflated the WMH volume change as subtle WMH at baseline that became more intense at follow-up were counted as increase in the volumetric change. Measurement of WMH volume change remains

Role of np fertilizer under different application methods on seed yield of sunflower

International Nuclear Information System (INIS)

Khan, R.U.; Khan, R.A.; Khan, R.A.; Muendal, H.

2007-01-01

The effects of different application methods of nitrogen and phophorus fertilizers were studied on the sunflower hybrid NK-212 during spring and kharif seasons at National Agricultural Research Centre, Islamabad. Nitrogen and phosphorus were applied at the rate 90 and 60 kg P 2 degree 5 ha-1 in a different proportions i.e. all broadcast and disked, 3/4 broadcast disked + 1/4 side banded, 1/2 broadcast disked + 1/2 side banded, 1/4 broadcast disked + 3/4 side banded and all side banded. Fertilizer applied in equal proportions of side banded and broadcast at the time of planting gave maximum (1525 and 1348 kg ha-1) seed yield and largest (14.3 cm and 10.15 cm) head diameter of sunflower in spring seasons during (1987 and 1988), and seed yield of 1206 kg ha-1 and 11.0 cm head diameter during kharif 1987. A significant increase in the 1000 seed weight was also observed in all the treatments receiving different split applications of N and P over all broadcast applied fertilizer. Plant height was not increased by split applications, with lowest height to be associated with most side banding of fertilizers. (author)

Testing Significance Testing

Directory of Open Access Journals (Sweden)

Joachim I. Krueger

2018-04-01

Full Text Available The practice of Significance Testing (ST remains widespread in psychological science despite continual criticism of its flaws and abuses. Using simulation experiments, we address four concerns about ST and for two of these we compare ST’s performance with prominent alternatives. We find the following: First, the 'p' values delivered by ST predict the posterior probability of the tested hypothesis well under many research conditions. Second, low 'p' values support inductive inferences because they are most likely to occur when the tested hypothesis is false. Third, 'p' values track likelihood ratios without raising the uncertainties of relative inference. Fourth, 'p' values predict the replicability of research findings better than confidence intervals do. Given these results, we conclude that 'p' values may be used judiciously as a heuristic tool for inductive inference. Yet, 'p' values cannot bear the full burden of inference. We encourage researchers to be flexible in their selection and use of statistical methods.

Development of flurbiprofen-loaded nanoparticles with a narrow size distribution using sucrose.

Science.gov (United States)

Oh, Dong Hoon; Yan, Yi-Dong; Kim, Dong Wuk; Kim, Jong Oh; Yong, Chul Soon; Choi, Han-Gon

2014-02-01

A novel flurbiprofen-loaded nanoemulsion which gave uniform emulsion droplets with a narrow size distribution was previously reported to be prepared using membrane emulsification method. The purpose of this study is to develop a novel flurbiprofen-loaded nanoparticle with a narrow size distribution and improved bioavailability. The nanoparticle was prepared by solidifying nanoemulsion using sucrose as a carrier via spray drying method. Its physicochemical properties were investigated using SEM, DSC and PXRD. Furthermore, dissolution and bioavailability in rats were evaluated compared to a flurbiprofen-loaded commercial product. The flurbiprofen-loaded nanoparticles with flurbiprofen/sucrose/surfactant mixture (1/20/2, weight ratio) gave good solidification and no stickiness. They associated with about 70,000-fold improved drug solubility and had a mean size of about 300 nm with a narrow size distribution. Flurbiprofen was present in a changed amorphous state in these nanoparticles. Moreover, the nanoparticles gave significantly shorter Tmax, and higher AUC and Cmax of the drug compared to the commercial product (p flurbiprofen-loaded nanoparticles prepared with sucrose by the membrane emulsification and spray drying method would be a potential candidate for orally delivering poorly water-soluble flurbiprofen with enhanced bioavailability.

Management of nitrogen fertigation of tomato with the use of 15N technology

International Nuclear Information System (INIS)

Zuraiqi, S.; Qawasmi, W.; Deek, I.; Mohammad, M.J.

2002-01-01

Field studies were conducted during two seasons at the Deir Alla Research Center to compare the conventional fertilization method with fertigation on water and nitrogen use efficiency with a tomato crop (cv. Gardenia). Four N application rates (0, 50, 100 and 150 mg N/L) were applied with the irrigation water and one soil application (NS) treatment, equivalent to one of the fertigation treatments, was included. Labelled ammonium sulfate was applied to microplots within the macroplots to evaluate the N recovery and utilization efficiency. Results obtained from two seasons indicate that increasing the N rate significantly increased the total and marketable yield by both methods of application, suggesting that the crop was underfertilized. The soil application treatment gave a higher yield than the control (N0) and a lower one than the fertigated treatments. In comparison to the N0, the total number of fruits in both seasons was significantly increased at all N levels. The soil application (Ns) treatment gave the lowest number of fruits compared to the fertigation treatments in the first season and a higher number than the fertigated treatments in the second season. The parameters of fruit quality (pH of juice, titratable acidity (TA%) and total soluble solids (TSS%)) were in the acceptable range. They were not significantly affected by the rates and methods of the N application in both seasons. The rates and methods of N application did not affect the accumulation of dry matter (DM) of the fruits and shoots during the first season. But in the second season, the accumulation was higher than in the first season and it was significantly affected by the concentration and method of N application. With the soil application treatment (Ns) a higher DM content was accumulated than in the control (N0), but lower than the fertigated treatments. The total N uptake by the fruits and shoots during both seasons with the fertigated treatments was higher than with the soil

‘And God gave Solomon wisdom’: Proficiency in ornithomancy

Directory of Open Access Journals (Sweden)

Abraham O. Shemesh

2018-04-01

Full Text Available The biblical text accords a great deal of attention to King Solomon’s personal abilities and governmental power. Solomon was described as a judge, poet, constructor and the wisest of all people in the Ancient Near East and Egypt. The current study discusses the interpretation of the midrashim that show how Solomon’s wisdom was manifested in his considerable knowledge of ornithomancy, that is, divination using birds, a practice that was considered as an important wisdom in the ancient world because of its practical applications, particularly in the military sphere. It seems that Solomon’s portrayal as a magician is intended and aimed at emphasising his abilities and his impressive character. Moreover, it may have had the purpose of disproving the conception of Solomon as inferior to his surroundings in this respect and the idea that he or his kingdom could be controlled by nations that command this type of wisdom.

A Novel Least Significant Bit First Processing Parallel CRC Circuit

Directory of Open Access Journals (Sweden)

Xiujie Qu

2013-01-01

Full Text Available In HDLC serial communication protocol, CRC calculation can first process the most or least significant bit of data. Nowadays most CRC calculation is based on the most significant bit (MSB first processing. An algorithm of the least significant bit (LSB first processing parallel CRC is proposed in this paper. Based on the general expression of the least significant bit first processing serial CRC, using state equation method of linear system, we derive a recursive formula by the mathematical deduction. The recursive formula is applicable to any number of bits processed in parallel and any series of generator polynomial. According to the formula, we present the parallel circuit of CRC calculation and implement it with VHDL on FPGA. The results verify the accuracy and effectiveness of this method.

Applicability of simplified methods to evaluate consequences of criticality accident using past accident data

International Nuclear Information System (INIS)

Nakajima, Ken

2003-01-01

Applicability of four simplified methods to evaluate the consequences of criticality accident was investigated. Fissions in the initial burst and total fissions were evaluated using the simplified methods and those results were compared with the past accident data. The simplified methods give the number of fissions in the initial burst as a function of solution volume; however the accident data did not show such tendency. This would be caused by the lack of accident data for the initial burst with high accuracy. For total fissions, simplified almost reproduced the upper envelope of the accidents. However several accidents, which were beyond the applicable conditions, resulted in the larger total fissions than the evaluations. In particular, the Tokai-mura accident in 1999 gave in the largest total specific fissions, because the activation of cooling system brought the relatively high power for a long time. (author)

Factoring local sequence composition in motif significance analysis.

Science.gov (United States)

Ng, Patrick; Keich, Uri

2008-01-01

We recently introduced a biologically realistic and reliable significance analysis of the output of a popular class of motif finders. In this paper we further improve our significance analysis by incorporating local base composition information. Relying on realistic biological data simulation, as well as on FDR analysis applied to real data, we show that our method is significantly better than the increasingly popular practice of using the normal approximation to estimate the significance of a finder's output. Finally we turn to leveraging our reliable significance analysis to improve the actual motif finding task. Specifically, endowing a variant of the Gibbs Sampler with our improved significance analysis we demonstrate that de novo finders can perform better than has been perceived. Significantly, our new variant outperforms all the finders reviewed in a recently published comprehensive analysis of the Harbison genome-wide binding location data. Interestingly, many of these finders incorporate additional information such as nucleosome positioning and the significance of binding data.

Evaluation of Pentachlorophenol Residues in Some Hygienic Papers Prepared from Virgin and Secondary Pulp by Electron Capture Gas Chromatographic Method

Directory of Open Access Journals (Sweden)

Behrouz Akbari-adergani

2016-01-01

Full Text Available In this study, residual amount of pentachlorophenol (PCP as the most important paper preservative, which is extremely hazardous pollutant, was determined in some tissue papers and napkins. Twenty-five samples of two producing hygienic paper factories prepared from virgin and secondary pulp were analyzed for the presence of trace amount of PCP. The analytical procedure involved direct extraction of PCP from hygienic paper and its determination by gas chromatography with electron capture detection. The statistical results for the analysis of all samples revealed that there were significant differences between mean of PCP in hygienic papers prepared from virgin and secondary pulp (P<0.05. This method gave recoveries of 86-98% for hygienic paper made from virgin pulp and 79-92% for hygienic paper made from secondary pulp. The limit of detection (LOD and limit of quantification (LOQ for PCP were 6.3 and 21.0 mg/kg, respectively. The analytical method has the requisite sensitivity, accuracy, precision and specificity to assay PCP in hygienic papers. This study demonstrates a concern with exposition to PCP considering that hygienic paper is largely consumed in the society.

The Effect of NaOH Concentration on pH, Egg White Protein Content and Yolk Colour Pidan Egg

Directory of Open Access Journals (Sweden)

Herly Evanuarini

2017-11-01

Full Text Available The purpose of this research was to determine the best treatment NaOH addition on pidan eggs. The materials used for this research was pidan made from duck egg, NaOH, salt, black tea and water. The method was used experiment laboratory and Completely Randomized Design (CRD using 4 treatments and 4 replications. The treatments were T0 (control, T1 (1.4%, T2 (2.8% and T3 (4.2%. The data were analyzed by Analysis of Variance (ANOVA if there was significantly continued by Duncan’s Multiple Range Test (DMRT. The result showed that NaOH concentration on pidan eggs gave significant effect (P<0.05 on albumen protein content, gave highly significant (P<0.01 on pH value and yolk colour. The conclusion of this research was 4.2% NaOH addition on pidan egg was the best treatment with gave result yolk and albumen pH: 10.69; 10.25, albumen protein content 26.89%, egg yolk colour L* (lightness, a* (redness, b* (yellowness:  26.89; 11.33, and 26.77. The suggestion of this research was ussed different immersion time on pidan egg production.

Method evaluation of Fusarium DNA extraction from mycelia and wheat for down-stream real-time PCR quantification and correlation to mycotoxin levels.

Science.gov (United States)

Fredlund, Elisabeth; Gidlund, Ann; Olsen, Monica; Börjesson, Thomas; Spliid, Niels Henrik Hytte; Simonsson, Magnus

2008-04-01

Identification of Fusarium species by traditional methods requires specific skill and experience and there is an increased interest for new molecular methods for identification and quantification of Fusarium from food and feed samples. Real-time PCR with probe technology (Taqman) can be used for the identification and quantification of several species of Fusarium from cereal grain samples. There are several critical steps that need to be considered when establishing a real-time PCR-based method for DNA quantification, including extraction of DNA from the samples. In this study, several DNA extraction methods were evaluated, including the DNeasy Plant Mini Spin Columns (Qiagen), the Bio robot EZ1 (Qiagen) with the DNeasy Blood and Tissue Kit (Qiagen), and the Fast-DNA Spin Kit for Soil (Qbiogene). Parameters such as DNA quality and stability, PCR inhibitors, and PCR efficiency were investigated. Our results showed that all methods gave good PCR efficiency (above 90%) and DNA stability whereas the DNeasy Plant Mini Spin Columns in combination with sonication gave the best results with respect to Fusarium DNA yield. The modified DNeasy Plant Mini Spin protocol was used to analyse 31 wheat samples for the presence of F. graminearum and F. culmorum. The DNA level of F. graminearum could be correlated to the level of DON (r(2) = 0.9) and ZEN (r(2) = 0.6) whereas no correlation was found between F. culmorum and DON/ZEA. This shows that F. graminearum and not F. culmorum, was the main producer of DON in Swedish wheat during 2006.

Comparison of different methods for activation analysis of geological and pedological samples: Reactor and epithermal neutron activation, relative and monostandard method

International Nuclear Information System (INIS)

Alian, A.; Sansoni, B.

1980-04-01

Using purely instrumental methods, a comparative study is presented on neutron activation analysis of rock and soil samples by whole reactor neutron spectrum and epithermal neutrons with both relative and monostandard procedures. The latter procedure used with epithermal neutron activation analysis of soil samples necessitated the use of the 'effective resonance integrals' which were determined experimentally. The incorporation of the #betta# factor, representing deviation of reactor epithermal neutron flux from 1/E law, is developed in the present work. The main criteria for the choice of one or more of the procedures studied for a given purpose are also indicated. Analysis of 15 trace elements, Ca and Fe in the standard Japanese granite JG-1 using monostandard epithermal neutron activation gave results in good agreement with the average literature values. (orig./RB) [de

Comparing the normalization methods for the differential analysis of Illumina high-throughput RNA-Seq data.

Science.gov (United States)

Li, Peipei; Piao, Yongjun; Shon, Ho Sun; Ryu, Keun Ho

2015-10-28

Recently, rapid improvements in technology and decrease in sequencing costs have made RNA-Seq a widely used technique to quantify gene expression levels. Various normalization approaches have been proposed, owing to the importance of normalization in the analysis of RNA-Seq data. A comparison of recently proposed normalization methods is required to generate suitable guidelines for the selection of the most appropriate approach for future experiments. In this paper, we compared eight non-abundance (RC, UQ, Med, TMM, DESeq, Q, RPKM, and ERPKM) and two abundance estimation normalization methods (RSEM and Sailfish). The experiments were based on real Illumina high-throughput RNA-Seq of 35- and 76-nucleotide sequences produced in the MAQC project and simulation reads. Reads were mapped with human genome obtained from UCSC Genome Browser Database. For precise evaluation, we investigated Spearman correlation between the normalization results from RNA-Seq and MAQC qRT-PCR values for 996 genes. Based on this work, we showed that out of the eight non-abundance estimation normalization methods, RC, UQ, Med, TMM, DESeq, and Q gave similar normalization results for all data sets. For RNA-Seq of a 35-nucleotide sequence, RPKM showed the highest correlation results, but for RNA-Seq of a 76-nucleotide sequence, least correlation was observed than the other methods. ERPKM did not improve results than RPKM. Between two abundance estimation normalization methods, for RNA-Seq of a 35-nucleotide sequence, higher correlation was obtained with Sailfish than that with RSEM, which was better than without using abundance estimation methods. However, for RNA-Seq of a 76-nucleotide sequence, the results achieved by RSEM were similar to without applying abundance estimation methods, and were much better than with Sailfish. Furthermore, we found that adding a poly-A tail increased alignment numbers, but did not improve normalization results. Spearman correlation analysis revealed that RC, UQ

Radioimmunoassay and chemical ionization/mass spectrometry compared for plasma cortisol determination

International Nuclear Information System (INIS)

Lindberg, C.; Johnson, S.; Hedner, P.; Gustafsson, A.

1982-01-01

A method is described for determination of cortisol in plasma and urine, based on chemical ionization/mass spectrometry with deuterium-labeled cortisol as the internal standard. The within-run precision (CV) was 2.5-5.7%, the between-run precision 4.6%. Results by this method were compared with those by a radioimmunological method (RIANEN Cortisol, New England Nuclear) for 395 plasma samples. The latter method gave significantly higher (approx. 25%) cortisol values

Criticality Analysis Of TCA Critical Lattices With MNCP-4C Monte Carlo Calculation

International Nuclear Information System (INIS)

Zuhair

2002-01-01

The use of uranium-plutonium mixed oxide (MOX) fuel in electric generation light water reactor (PWR, BWR) is being planned in Japan. Therefore, the accuracy evaluations of neutronic analysis code for MOX cores have been employed by many scientists and reactor physicists. Benchmark evaluations for TCA was done using various calculation methods. The Monte Carlo become the most reliable method to predict criticality of various reactor types. In this analysis, the MCNP-4C code was chosen because various superiorities the code has. All in all, the MCNP-4C calculation for TCA core with 38 MOX critical lattice configurations gave the results with high accuracy. The JENDL-3.2 library showed significantly closer results to the ENDF/B-V. The k eff values calculated with the ENDF/B-VI library gave underestimated results. The ENDF/B-V library gave the best estimation. It can be concluded that MCNP-4C calculation, especially with ENDF/B-V and JENDL-3.2 libraries, for MOX fuel utilized NPP design in reactor core is the best choice

Association between micronucleus frequency and cervical intraepithelial neoplasia grade in Thinprep cytological test and its significance.

Science.gov (United States)

Shi, Yong-Hua; Wang, Bo-Wei; Tuokan, Talaf; Li, Qiao-Zhi; Zhang, Ya-Jing

2015-01-01

A micronucleus is an additional small nucleus formed due to chromosomes or chromosomal fragments fail to be incorporated into the nucleus during cell division. In this study, we assessed the utility of micronucleus counting as a screening tool in cervical precancerous lesions in Thinprep cytological test smears under oil immersion. High risk HPV was also detected by hybrid capture-2 in Thinprep cytological test smears. Our results showed that micronucleus counting was significantly higher in high-grade squamous intraepithelial lesion (HSIL) and invasive carcinoma cases compared to low-grade squamous intraepithelial lesion (LSIL) and non-neoplastic cases. Receiver operating characteristic (ROC) curve analysis revealed that micronucleus counting possessed a high degree of sensitivity and specificity for identifying HSIL and invasive carcinoma. Cut-off of 7.5 for MN counting gave a sensitivity of 89.6% and a specificity of 66.7% (P = 0.024 and AUC = 0.892) for detecting HSIL and invasive carcinoma lesions. Multiple linear regression analysis showed that only HSIL and invasive cancer lesions not age, duration of marital life and number of pregnancy are significantly associated with MN counting. The positive rate of high risk HPV was distinctly higher in LSIL, HSIL and invasive cancer than that in non-neoplstic categories. In conclusions, MN evaluation may be viewed as an effective biomarker for cervical cancer screening. The combination of MN count with HPV DNA detection and TCT may serve as an effective means to screen precancerous cervical lesions in most developing nations.

A multiplex PCR-based method to identify strongylid parasite larvae recovered from ovine faecal cultures and/or pasture samples.

Science.gov (United States)

Bisset, S A; Knight, J S; Bouchet, C L G

2014-02-24

A multiplex PCR-based method was developed to overcome the limitations of microscopic examination as a means of identifying individual infective larvae from the wide range of strongylid parasite species commonly encountered in sheep in mixed sheep-cattle grazing situations in New Zealand. The strategy employed targets unique species-specific sequence markers in the second internal transcribed spacer (ITS-2) region of ribosomal DNA of the nematodes and utilises individual larval lysates as reaction templates. The basic assay involves two sets of reactions designed to target the ten strongylid species most often encountered in ovine faecal cultures under New Zealand conditions (viz. Haemonchus contortus, Teladorsagia circumcincta, Trichostrongylus axei, Trichostrongylus colubriformis, Trichostrongylus vitrinus, Cooperia curticei, Cooperia oncophora, Nematodirus spathiger, Chabertia ovina, and Oesophagostomum venulosum). Five species-specific primers, together with a pair of "generic" (conserved) primers, are used in each of the reactions. Two products are generally amplified, one by the generic primer pair regardless of species (providing a positive PCR control) and the other (whose size is indicative of the species present) by the appropriate species-specific primer in combination with one or other of the generic primers. If necessary, any larvae not identified by these reactions can subsequently be tested using primers designed specifically to detect those species less frequently encountered in ovine faecal cultures (viz. Ostertagia ostertagi, Ostertagia leptospicularis, Cooperia punctata, Nematodirus filicollis, and Bunostomum trigonocephalum). Results of assays undertaken on >5500 nematode larvae cultured from lambs on 16 different farms distributed throughout New Zealand indicated that positive identifications were initially obtained for 92.8% of them, while a further 4.4% of reactions gave a generic but no visible specific product and 2.8% gave no discernible

Significance analysis of lexical bias in microarray data

Directory of Open Access Journals (Sweden)

Falkow Stanley

2003-04-01

Full Text Available Abstract Background Genes that are determined to be significantly differentially regulated in microarray analyses often appear to have functional commonalities, such as being components of the same biochemical pathway. This results in certain words being under- or overrepresented in the list of genes. Distinguishing between biologically meaningful trends and artifacts of annotation and analysis procedures is of the utmost importance, as only true biological trends are of interest for further experimentation. A number of sophisticated methods for identification of significant lexical trends are currently available, but these methods are generally too cumbersome for practical use by most microarray users. Results We have developed a tool, LACK, for calculating the statistical significance of apparent lexical bias in microarray datasets. The frequency of a user-specified list of search terms in a list of genes which are differentially regulated is assessed for statistical significance by comparison to randomly generated datasets. The simplicity of the input files and user interface targets the average microarray user who wishes to have a statistical measure of apparent lexical trends in analyzed datasets without the need for bioinformatics skills. The software is available as Perl source or a Windows executable. Conclusion We have used LACK in our laboratory to generate biological hypotheses based on our microarray data. We demonstrate the program's utility using an example in which we confirm significant upregulation of SPI-2 pathogenicity island of Salmonella enterica serovar Typhimurium by the cation chelator dipyridyl.

Effect of Different Sterilization Methods on the Extracted Oil from Oil Palm Fruit

International Nuclear Information System (INIS)

Hasimah Kasmin; Hasimah Kasmin; Roila Awang; Azwan Mat Lazim

2015-01-01

Sterilization is important process during the processing of oil palm fruits in order to produce crude palm oil (CPO). This process can be carried out using steam (conventional method), dry heating or wet heating method. In this study, the effectiveness of the dry heating and wet heating method for sterilization and solvent extraction were carried out. The sterilization time of these two methods were varied at 30, 60 and 90 min in order to determine their effectiveness on the oil extraction and their quality. Results showed that, at 30 min of sterilization, the wet heating produced a higher percentage of oil extraction compared to the conventional and dry heating, with average of 27.65 %, 19.01 % and 20.21 % respectively. In comparison with the conventional method, both sterilization methods gave better FFA and DOBI results. This can be seen where the average of free fatty acid (FFA) content for proposed sterilization method was between 0.37 % to 0.93 % while, average deterioration of bleach ability index (DOBI) was from 4.89 to 6.12. The average carotene content was in agreement with the conventional method at a range of 644.64 ppm to 764.80 ppm. (author)

Mercury speciation analysis in seafood by species-specific isotope dilution: method validation and occurrence data

Energy Technology Data Exchange (ETDEWEB)

Clemens, Stephanie; Guerin, Thierry [Agence Nationale de Securite Sanitaire de l' Alimentation, Laboratoire de Securite des Aliments de Maisons-Alfort, Unite des Contaminants Inorganiques et Mineraux de l' Environnement, ANSES, Maisons-Alfort (France); Monperrus, Mathilde; Donard, Olivier F.X.; Amouroux, David [IPREM UMR 5254 CNRS - Universite de Pau et des Pays de l' Adour, Laboratoire de Chimie Analytique Bio-Inorganique et Environnement, Institut des Sciences Analytiques et de Physico-chimie pour l' Environnement et les Materiaux, Pau Cedex (France)

2011-11-15

Methylmercury (MeHg) and total mercury (THg) in seafood were determined using species-specific isotope dilution analysis and gas chromatography combined with inductively coupled plasma mass spectrometry. Sample preparation methods (extraction and derivation step) were evaluated on certified reference materials using isotopically enriched Hg species. Solid-liquid extraction, derivation by propylation and automated agitation gave excellent accuracy and precision results. Satisfactory figures of merit for the selected method were obtained in terms of limit of quantification (1.2 {mu}g Hg kg{sup -1} for MeHg and 1.4 {mu}g Hg kg{sup -1} for THg), repeatability (1.3-1.7%), intermediate precision reproducibility (1.5% for MeHg and 2.2% for THg) and trueness (bias error less than 7%). By means of a recent strategy based on accuracy profiles ({beta}-expectation tolerance intervals), the selected method was successfully validated in the range of approximately 0.15-5.1 mg kg{sup -1} for MeHg and 0.27-5.2 mg kg{sup -1} for THg. Probability {beta} was set to 95% and the acceptability limits to {+-}15%. The method was then applied to 62 seafood samples representative of consumption in the French population. The MeHg concentrations were generally low (1.9-588 {mu}g kg{sup -1}), and the percentage of MeHg varied from 28% to 98% in shellfish and from 84% to 97% in fish. For all real samples tested, methylation and demethylation reactions were not significant, except in one oyster sample. The method presented here could be used for monitoring food contamination by MeHg and inorganic Hg in the future to more accurately assess human exposure. (orig.)

A comparison of five methods of measuring mammographic density: a case-control study.

Science.gov (United States)

Astley, Susan M; Harkness, Elaine F; Sergeant, Jamie C; Warwick, Jane; Stavrinos, Paula; Warren, Ruth; Wilson, Mary; Beetles, Ursula; Gadde, Soujanya; Lim, Yit; Jain, Anil; Bundred, Sara; Barr, Nicola; Reece, Valerie; Brentnall, Adam R; Cuzick, Jack; Howell, Tony; Evans, D Gareth

2018-02-05

High mammographic density is associated with both risk of cancers being missed at mammography, and increased risk of developing breast cancer. Stratification of breast cancer prevention and screening requires mammographic density measures predictive of cancer. This study compares five mammographic density measures to determine the association with subsequent diagnosis of breast cancer and the presence of breast cancer at screening. Women participating in the "Predicting Risk Of Cancer At Screening" (PROCAS) study, a study of cancer risk, completed questionnaires to provide personal information to enable computation of the Tyrer-Cuzick risk score. Mammographic density was assessed by visual analogue scale (VAS), thresholding (Cumulus) and fully-automated methods (Densitas, Quantra, Volpara) in contralateral breasts of 366 women with unilateral breast cancer (cases) detected at screening on entry to the study (Cumulus 311/366) and in 338 women with cancer detected subsequently. Three controls per case were matched using age, body mass index category, hormone replacement therapy use and menopausal status. Odds ratios (OR) between the highest and lowest quintile, based on the density distribution in controls, for each density measure were estimated by conditional logistic regression, adjusting for classic risk factors. The strongest predictor of screen-detected cancer at study entry was VAS, OR 4.37 (95% CI 2.72-7.03) in the highest vs lowest quintile of percent density after adjustment for classical risk factors. Volpara, Densitas and Cumulus gave ORs for the highest vs lowest quintile of 2.42 (95% CI 1.56-3.78), 2.17 (95% CI 1.41-3.33) and 2.12 (95% CI 1.30-3.45), respectively. Quantra was not significantly associated with breast cancer (OR 1.02, 95% CI 0.67-1.54). Similar results were found for subsequent cancers, with ORs of 4.48 (95% CI 2.79-7.18), 2.87 (95% CI 1.77-4.64) and 2.34 (95% CI 1.50-3.68) in highest vs lowest quintiles of VAS, Volpara and Densitas

The significance of amlodipine on autonomic nervous system adjustment (ANSA method: A new approach in the treatment of hypertension

Directory of Open Access Journals (Sweden)

Milovanović Branislav

2009-01-01

Full Text Available Introduction. Cardiovascular autonomic modulation is altered in patients with essential hypertension. Objective To evaluate acute and long-term effects of amlodipine on cardiovascular autonomic function and haemodynamic status in patients with mild essential hypertension. Methods. Ninety patients (43 male, mean age 52.12 ±10.7 years with mild hypertension were tested before, 30 minutes after the first 5 mg oral dose of amlodipine and three weeks after monotherapy with amlodipine. A comprehensive study protocol was done including finger blood pressure variability (BPV and heart rate variability (HRV beat-to-beat analysis with impedance cardiography, ECG with software short-term HRV and nonlinear analysis, 24-hour Holter ECG monitoring with QT and HRV analysis, 24-hour blood pressure (BP monitoring with systolic and diastolic BPV analysis, cardiovascular autonomic reflex tests, cold pressure test, mental stress test. The patients were also divided into sympathetic and parasympathetic groups, depending on predominance in short time spectral analysis of sympathovagal balance according to low frequency and high frequency values. Results. We confirmed a significant systolic and diastolic BP reduction, and a reduction of pulse pressure during day, night and early morning hours. The reduction of supraventricular and ventricular ectopic beats during the night was also achieved with therapy, but without statistical significance. The increment of sympathetic activity in early phase of amlodipine therapy was without statistical significance and persistence of sympathetic predominance after a few weeks of therapy detected based on the results of short-term spectral HRV analysis. All time domain parameters of long-term HRV analysis were decreased and low frequency amongst spectral parameters. Amlodipne reduced baroreflex sensitivity after three weeks of therapy, but increased it immediately after the administration of the first dose. Conclusion. The results

The significance of appearance in physician-nurse collaboration

DEFF Research Database (Denmark)

Konradsen, H.; Christensen, O.M.; Berthelsen, C.

2009-01-01

INTRODUCTION: According to nurses' assessment, physician-nurse collaboration is problematic. The aim of the study was to investigate whether nurses believe physicians' appearances is significant for their ability to collaborate. MATERIAL AND METHODS: This is a single-blinded, quasi-experimental i......-depth interviews to achieve harmonic interaction leading to a prolific and close future collaboration Udgivelsesdato: 2009/12/14......INTRODUCTION: According to nurses' assessment, physician-nurse collaboration is problematic. The aim of the study was to investigate whether nurses believe physicians' appearances is significant for their ability to collaborate. MATERIAL AND METHODS: This is a single-blinded, quasi....... The Jefferson Scale of Attitudes Toward Physician-Nurse Collaboration will be used for baseline and follow-up study of the nurses' assessment. RESULTS: Due to ethical considerations, researchers had difficulties finding surgeons prepared to perform procedures aiming at weakening the physicians' physical...

Polynomial regression analysis and significance test of the regression function

International Nuclear Information System (INIS)

Gao Zhengming; Zhao Juan; He Shengping

2012-01-01

In order to analyze the decay heating power of a certain radioactive isotope per kilogram with polynomial regression method, the paper firstly demonstrated the broad usage of polynomial function and deduced its parameters with ordinary least squares estimate. Then significance test method of polynomial regression function is derived considering the similarity between the polynomial regression model and the multivariable linear regression model. Finally, polynomial regression analysis and significance test of the polynomial function are done to the decay heating power of the iso tope per kilogram in accord with the authors' real work. (authors)

A simplified ultrafiltration method for determination of serum free cortisol

International Nuclear Information System (INIS)

MacMahon, W.; Sgoutas, D.

1983-01-01

The authors describe the suitability of the Amicon MPS-1 centrifugal ultrafiltration device and the YMB membrane for measuring free cortisol in serum. The method combines two independent assays: total cortisol and the ultrafiltrate fraction of added [ 3 H]cortisol. The unbound fraction is determined in 0.25-0.30 ml of ultrafiltrate collected from 0.6 to 1 ml of serum that has been equilibrated with [ 3 H]cortisol at 37 0 C for 20 min. The assay is rapid (less than 1 h), practical (no more than 0.6 ml of serum is necessary) and repeatable (CV: 3.8% within-assay and 12.2% in different assays). Error introduced in free cortisol measurement due to dilution effects in dialysis is systematically defined, and the effect of tracer purity on the ultrafiltration method is examined. Dialyzed sera from normal men and women, from patients with Cushing's disease and adrenal insufficiency, and from pregnant women gave ultrafiltration results that accurately duplicated those obtained by previous dialysis. (Auth.)

2D-3D Face Recognition Method Basedon a Modified CCA-PCA Algorithm

Directory of Open Access Journals (Sweden)

Patrik Kamencay

2014-03-01

Full Text Available This paper presents a proposed methodology for face recognition based on an information theory approach to coding and decoding face images. In this paper, we propose a 2D-3D face-matching method based on a principal component analysis (PCA algorithm using canonical correlation analysis (CCA to learn the mapping between a 2D face image and 3D face data. This method makes it possible to match a 2D face image with enrolled 3D face data. Our proposed fusion algorithm is based on the PCA method, which is applied to extract base features. PCA feature-level fusion requires the extraction of different features from the source data before features are merged together. Experimental results on the TEXAS face image database have shown that the classification and recognition results based on the modified CCA-PCA method are superior to those based on the CCA method. Testing the 2D-3D face match results gave a recognition rate for the CCA method of a quite poor 55% while the modified CCA method based on PCA-level fusion achieved a very good recognition score of 85%.

Zooplankton - Study methods, importance and significant observations

Digital Repository Service at National Institute of Oceanography (India)

Gajbhiye, S.N.

density, shorter life span, drifting nature, high group/species diversity and different tolerance to the stress, they are being used as the indicator organisms for the physical, chemical and biological processes in the aquatic ecosystem. In the deeper...

Methods of chemical and phase composition analysis of gallstones

Science.gov (United States)

Suvorova, E. I.; Pantushev, V. V.; Voloshin, A. E.

2017-11-01

This review presents the instrumental methods used for chemical and phase composition investigation of gallstones. A great body of data has been collected in the literature on the presence of elements and their concentrations, obtained by fluorescence microscopy, X-ray fluorescence spectroscopy, neutron activation analysis, proton (particle) induced X-ray emission, atomic absorption spectroscopy, high-resolution gamma-ray spectrometry, electron paramagnetic resonance. Structural methods—powder X-ray diffraction, infrared spectroscopy, Raman spectroscopy—provide information about organic and inorganic phases in gallstones. Stone morphology was studied at the macrolevel with optical microscopy. Results obtained by analytical scanning and transmission electron microscopy with X-ray energy dispersive spectrometry are discussed. The chemical composition and structure of gallstones determine the strategy of removing stone from the body and treatment of patients: surgery or dissolution in the body. Therefore one chapter of the review describes the potential of dissolution methods. Early diagnosis and appropriate treatment of the disease depend on the development of clinical methods for in vivo investigation, which gave grounds to present the main characteristics and potential of ultrasonography (ultrasound scanning), magnetic resonance imaging, and X-ray computed tomography.

Workshop on methods for siting groundwater monitoring wells: Proceedings

International Nuclear Information System (INIS)

Jacobson, E.

1992-02-01

The primary purpose of this workshop was to identify methods for the optimum siting of groundwater monitoring wells to minimize the number required that will provide statistically and physically representative samples. In addition, the workshop served to identify information and data gaps, stimulated discussion and provided an opportunity for exchange of ideas between regulators and scientists interested in siting groundwater monitoring wells. These proceedings should serve these objectives and provide a source of relevant information which may be used to evaluate the current state of development of methods for siting groundwater monitoring wells and the additional research needs. The proceedings contain the agenda and list of attendees in the first section. The abstract and viewgraphs for each presentation are given in the second section. For several presentations, abstracts and viewgraphs were not received. After the presentations, four working groups were organized and met for approximately a day. The working group leaders then gave a verbal summary of their sessions. This material was transcribed and is included in the next section of these proceedings. The appendices contain forms describing various methods discussed in the working groups

A comparison of methods for the analysis of binomial clustered outcomes in behavioral research.

Science.gov (United States)

Ferrari, Alberto; Comelli, Mario

2016-12-01

In behavioral research, data consisting of a per-subject proportion of "successes" and "failures" over a finite number of trials often arise. This clustered binary data are usually non-normally distributed, which can distort inference if the usual general linear model is applied and sample size is small. A number of more advanced methods is available, but they are often technically challenging and a comparative assessment of their performances in behavioral setups has not been performed. We studied the performances of some methods applicable to the analysis of proportions; namely linear regression, Poisson regression, beta-binomial regression and Generalized Linear Mixed Models (GLMMs). We report on a simulation study evaluating power and Type I error rate of these models in hypothetical scenarios met by behavioral researchers; plus, we describe results from the application of these methods on data from real experiments. Our results show that, while GLMMs are powerful instruments for the analysis of clustered binary outcomes, beta-binomial regression can outperform them in a range of scenarios. Linear regression gave results consistent with the nominal level of significance, but was overall less powerful. Poisson regression, instead, mostly led to anticonservative inference. GLMMs and beta-binomial regression are generally more powerful than linear regression; yet linear regression is robust to model misspecification in some conditions, whereas Poisson regression suffers heavily from violations of the assumptions when used to model proportion data. We conclude providing directions to behavioral scientists dealing with clustered binary data and small sample sizes. Copyright © 2016 Elsevier B.V. All rights reserved.

A direct method to visualise the aryl acylamidase activity on cholinesterases in polyacrylamide gels

Directory of Open Access Journals (Sweden)

Boopathy Rathanam

2000-12-01

Full Text Available Abstract Background In vertebrates, two types of cholinesterases exist, acetylcholinesterase and butyrylcholinesterase. The function of acetylcholinesterase is to hydrolyse acetylcholine, thereby terminating the neurotransmission at cholinergic synapse, while the precise physiological function of butyrylcholinesterase has not been identified. The presence of cholinesterases in tissues that are not cholinergically innervated indicate that cholinesterases may have functions unrelated to neurotransmission. Furthermore, cholinesterases display a genuine aryl acylamidase activity apart from their predominant acylcholine hydrolase activity. The physiological significance of this aryl acylamidase activity is also not known. The study on the aryl acylamidase has been, in part hampered by the lack of a specific method to visualise this activity. We have developed a method to visualise the aryl acylamidase activity on cholinesterase in polyacrylamide gels. Results The o-nitroaniline liberated from o-nitroacetanilide by the action of aryl acylamidase activity on cholinesterases, in the presence of nitrous acid formed a diazonium compound. This compound gave an azo dye complex with N-(1-napthyl-ethylenediamine, which appeared as purple bands in polyacrylamide gels. Treating the stained gels with trichloroacetic acid followed by Tris-HCl buffer helped in fixation of the stain in the gels. By using specific inhibitors for acetylcholinesterase and butyrylcholinesterase, respectively, differential staining for the aryl acylamidase activities on butyrylcholinesterase and acetylcholinesterase in a sample containing both these enzymes has been demonstrated. A linear relationship between the intensity of colour developed and activity of the enzyme was obtained. Conclusions A novel method to visualise the aryl acylamidase activity on cholinesterases in polyacrylamide gels has been developed.

Biogas Production from Rice Husk Waste by using Solid State Anaerobic Digestion (SSAD) Method

Science.gov (United States)

Matin, Hashfi Hawali Abdul; Hadiyanto

2018-02-01

An effort to obtain alternative energy is still interesting subject to be studied, especially production of biogas from agriculture waste. This paper was an overview of the latest development of biogas researches from rice husk waste by Solid State Anaerobic Digestion (SSAD). The main obstacle of biogas production from rice husk waste was the lignin content which is very difficult degraded by microbes. Various pretreatments have been conducted, either physically, chemically as well as biologically. The SSAD method was an attractive option because of the low water content of rice husk waste. The biogas yield by SSAD method gave more attractive result compared to Liquid Anaerobic Digestion (LAD) method. Various studies were still conducted in batch mode laboratory scale and also has not found optimum operating conditions. Research on a larger scale such as bench and pilot scale with continuous systems will be an increase trend in the future research.

Methods of scoring induced chromosome structural changes in barley

International Nuclear Information System (INIS)

Nicoleff, H.; Gecheff, K.

1976-01-01

In barley, a material widely used in mutation and chromosomal aberration studies, the method most frequently used for scoring induced chromosomal changes is still anaphase analysis. In this paper, data obtained after treatment of barley with gamma-rays and ethyleneimine (EI) and comparative scoring of aberrations in metaphase and anaphase are reported and discussed. It is evident that the metaphase aberrations induced by gamma-rays and ethyleneimine, due probably to their specific location, showed a differential manifestation during anaphase. Thus, after treatment with ethyleneimine a great portion of the induced aberrations, being located preferentially at the centromere regions, gave no scorable bridges, and an apparent excess of fragments was observed at anaphase. After gamma-irradiation the differences between metaphase and anaphase scoring were mainly due to a large portion of fragments escaping detection

The Gap of Self - States and Its Association to an Individual‟s Interaction and Emotional Bond to their Significant Relationships: A Correlational Study about Filipino Youth‟s Self - Discrepancy and Their Attachment Styl

Directory of Open Access Journals (Sweden)

Mae R. Galing

2017-05-01

Full Text Available A youth is expected to experience difficulties due to the opposing desire to be free while still remaining dependent to family and other significant individuals in their lives. Filipino youth are known as being family - oriented and being submissive which is one of the factors that pounds the importance of what people around them utters. Thus, creating a gap or discrepancy between what they truly want and what other people expect them to do. When these internal battles began, significant external aspects such as social interaction can be compromised. These occurrences can be elucidated by using the two frameworks Self - Discrepancy Theory and Attachment Style. In this study, correlational research design and survey method were employed to 384 Filipino Youth from Makati whom are selected through convenience sampling. Results of the study showed that the respondents have positive image of themselves. Also, a big majority of the respondents were discerned to have high discrepancies between their self - states. In this study, it was also seen that the respondents were dismissive and were characterized to be independent, self - reliant, and gave low importance to relationships. Finally, findings of this study revealed a weak positive correlation between secure attachment s tyle towards the self - discrepancy of the respondents while weak negative correlation was found between the rest of the attachment styles towards the discrepancy among their self - states. With this, the researchers recommended stabilizing internal discrepanc ies and strengthening significant relationships as the two were seen as big factors in respondents’ social interaction and self - esteem.

Intercomparison of leach-testing methods and the effects of waste-form composition on test type and duration

International Nuclear Information System (INIS)

Harvey, K.B.; Jensen, C.D.

1982-01-01

Several leach-testing methods were evaluated for their relevance as scoping tests appropriate to proposed Canadian conditions for the disposal of high-level nuclear waste, and a static, terminated leach test was chosen. For a particular glass composition, methods in which the leachant was replenished gave apparent leach rates up to ten times less than did the static test. Under static leaching conditions, the leach rate of a number of sodium borosilicate glasses was observed to first rise and then fall with leaching time. This behavior is explained in terms of a pH change in the leachant, which is itself a function of the glass composition. The implications of these observations on glass compositions and on leach-testing methods that are relevant to the needs of final disposal are briefly discussed

The significance of sense of coherence for the perceptions of task characteristics and stress during interruptions amongst a sample of public health nurses in Hong Kong: implications for nursing management.

Science.gov (United States)

Shiu, A T

1998-08-01

The study aimed to investigate the significance of sense of coherence (SOC) for the perceptions of task characteristics and for stress perceptions during interruptions of public health nurses (PHNs) with children in Hong Kong. The research design employed the experience sampling method. Convenience sampling was used to recruit 20 subjects. During stage one of the study a watch was worn that gave a signal at six random times each day for seven days to complete an experience sampling diary. PHNs on average responded to 34 signals (80%) to complete the diaries which collected data on work and family juggling, task characteristics, and their effects on mood states. At stage two respondents completed the SOC scale which measured confidence in life as comprehensible, manageable, and meaningful. Two major findings provide the focus for this paper. First, results indicate that there was positive correlation between SOC and perceived task characteristics. Second, results reveal that when interruptions occurred, PHNs with high SOC had higher positive affect and lower negative affect than PHNs with low SOC. These results suggest that SOC as a salutogenic model helps PHNs to cope with the family and work juggling as well as the occupational stress. Implications for nursing management on strengthening SOC of PHNs are discussed.

Combining evidence and values in priority setting: testing the balance sheet method in a low-income country.

Science.gov (United States)

Makundi, Emmanuel; Kapiriri, Lydia; Norheim, Ole Frithjof

2007-09-24

Procedures for priority setting need to incorporate both scientific evidence and public values. The aim of this study was to test out a model for priority setting which incorporates both scientific evidence and public values, and to explore use of evidence by a selection of stakeholders and to study reasons for the relative ranking of health care interventions in a setting of extreme resource scarcity. Systematic search for and assessment of relevant evidence for priority setting in a low-income country. Development of a balance sheet according to Eddy's explicit method. Eight group interviews (n-85), using a modified nominal group technique for eliciting individual and group rankings of a given set of health interventions. The study procedure made it possible to compare the groups' ranking before and after all the evidence was provided to participants. A rank deviation is significant if the rank order of the same intervention differed by two or more points on the ordinal scale. A comparison between the initial rank and the final rank (before deliberation) showed a rank deviation of 67%. The difference between the initial rank and the final rank after discussion and voting gave a rank deviation of 78%. Evidence-based and deliberative decision-making does change priorities significantly in an experimental setting. Our use of the balance sheet method was meant as a demonstration project, but could if properly developed be feasible for health planners, experts and health workers, although more work is needed before it can be used for laypersons.

Evaluation of a Three-Dimensional Stereophotogrammetric Method to Identify and Measure the Palatal Surface Area in Children With Unilateral Cleft Lip and Palate.

Science.gov (United States)

De Menezes, Marcio; Cerón-Zapata, Ana Maria; López-Palacio, Ana Maria; Mapelli, Andrea; Pisoni, Luca; Sforza, Chiarella

2016-01-01

To assess a three-dimensional (3D) stereophotogrammetric method for area delimitation and evaluation of the dental arches of children with unilateral cleft lip and palate (UCLP). Obtained data were also used to assess the 3D changes occurring in the maxillary arch with the use of orthopedic therapy prior to rhinocheiloplasty and before the first year of life. Within the collaboration between the Università degli Studi di Milano (Italy) and the University CES of Medellin (Colombia), 96 palatal cast models obtained from neonatal patients with UCLP were analyzed using a 3D stereophotogrammetric imaging system. The area of the minor and greater cleft segments on the digital dental cast surface were delineated by the visualization tool of the stereophotogrammetric software and then examined. "Trueness" of the measurements, as well as systematic and random errors between operators' tracings ("precision") were calculated. The method gave area measurements close to true values (errors lower than 2%), without systematic measurement errors for tracings by both interoperators and intraoperators (P > .05). Statistically significant differences (P digital dental casts and area measurements by the 3D stereophotogrammetric system revealed an accurate (true and precise) method for evaluating the stone casts of newborn patients with UCLP.

Unbiased proteomics analysis demonstrates significant variability in mucosal immune factor expression depending on the site and method of collection.

Directory of Open Access Journals (Sweden)

Kenzie M Birse

Full Text Available Female genital tract secretions are commonly sampled by lavage of the ectocervix and vaginal vault or via a sponge inserted into the endocervix for evaluating inflammation status and immune factors critical for HIV microbicide and vaccine studies. This study uses a proteomics approach to comprehensively compare the efficacy of these methods, which sample from different compartments of the female genital tract, for the collection of immune factors. Matching sponge and lavage samples were collected from 10 healthy women and were analyzed by tandem mass spectrometry. Data was analyzed by a combination of differential protein expression analysis, hierarchical clustering and pathway analysis. Of the 385 proteins identified, endocervical sponge samples collected nearly twice as many unique proteins as cervicovaginal lavage (111 vs. 61 with 55% of proteins common to both (213. Each method/site identified 73 unique proteins that have roles in host immunity according to their gene ontology. Sponge samples enriched for specific inflammation pathways including acute phase response proteins (p = 3.37×10(-24 and LXR/RXR immune activation pathways (p = 8.82×10(-22 while the role IL-17A in psoriasis pathway (p = 5.98×10(-4 and the complement system pathway (p = 3.91×10(-3 were enriched in lavage samples. Many host defense factors were differentially enriched (p<0.05 between sites including known/potential antimicrobial factors (n = 21, S100 proteins (n = 9, and immune regulatory factors such as serpins (n = 7. Immunoglobulins (n = 6 were collected at comparable levels in abundance in each site although 25% of those identified were unique to sponge samples. This study demonstrates significant differences in types and quantities of immune factors and inflammation pathways collected by each sampling technique. Therefore, clinical studies that measure mucosal immune activation or factors assessing HIV transmission should utilize

Detection methods of pulsed X-rays for transmission tomography with a linear accelerator

International Nuclear Information System (INIS)

Glasser, F.

1988-07-01

Appropriate detection methods are studied for the development of a high energy tomograph using a linear accelerator for nondestructive testing of bulky objects. The aim is the selection of detectors adapted to a pulsed X-ray source and with a good behavior under X-ray radiations of several MeV. Performance of semiconductors (HgI 2 , Cl doped CdTe, GaAs, Bi 12 Ge0 20 ) and a scintillator (Bi 4 Ge 3 0 12 ) are examined. A prototype tomograph gave images that show the validity of detectors for analysis of medium size equipment such as a concrete drum of 60 cm in diameter [fr

Radioimmunoassay and liquid-chromatographic analysis for free cortisol in urine compared with isotope dilution-mass spectrometry

International Nuclear Information System (INIS)

Lantto, O.

1982-01-01

Three different routine methods for analysis for urinary cortisol with those by a highly specific reference method based on isotope dilution-mass spectrometry (I) were compared. A ''high-performance'' liquid-chromatographic method (II) gave the most comparable results (regression coefficient 0.86, intercept 9 nmol/L). For some urines much lower values were obtained by I than by II. Two radioimmunoassay (III) methods, one involving direct assay and one involving extraction, gave less-accurate results (regression coefficients of 1.87 and 1.52 and intercepts of 86 and 12 nmol/L, respectively), although values obtained by III and by I correlated well (r = 0.95-0.99), indicating a relation between the free cortisol and the compounds interfering in III. The apparent accuracy for the extraction method was improved by using as calibration standards urine samples previously assayed by I (regression coefficient 0.90, intercept 6 nmol/L). All four methods investigated showed a statistically significant sex-related difference in 24-h urinary cortisol excretion; evidently such a finding should be a prerequisite in any such method proposed for routine use

Human Body 3D Posture Estimation Using Significant Points and Two Cameras

Science.gov (United States)

Juang, Chia-Feng; Chen, Teng-Chang; Du, Wei-Chin

2014-01-01

This paper proposes a three-dimensional (3D) human posture estimation system that locates 3D significant body points based on 2D body contours extracted from two cameras without using any depth sensors. The 3D significant body points that are located by this system include the head, the center of the body, the tips of the feet, the tips of the hands, the elbows, and the knees. First, a linear support vector machine- (SVM-) based segmentation method is proposed to distinguish the human body from the background in red, green, and blue (RGB) color space. The SVM-based segmentation method uses not only normalized color differences but also included angle between pixels in the current frame and the background in order to reduce shadow influence. After segmentation, 2D significant points in each of the two extracted images are located. A significant point volume matching (SPVM) method is then proposed to reconstruct the 3D significant body point locations by using 2D posture estimation results. Experimental results show that the proposed SVM-based segmentation method shows better performance than other gray level- and RGB-based segmentation approaches. This paper also shows the effectiveness of the 3D posture estimation results in different postures. PMID:24883422

Testing the Difference of Correlated Agreement Coefficients for Statistical Significance

Science.gov (United States)

Gwet, Kilem L.

2016-01-01

This article addresses the problem of testing the difference between two correlated agreement coefficients for statistical significance. A number of authors have proposed methods for testing the difference between two correlated kappa coefficients, which require either the use of resampling methods or the use of advanced statistical modeling…

Treatment of hyperthyroidism with radioiodine targeted activity: A comparison between two dosimetric methods.

Science.gov (United States)

Amato, Ernesto; Campennì, Alfredo; Leotta, Salvatore; Ruggeri, Rosaria M; Baldari, Sergio

2016-06-01

Radioiodine therapy is an effective and safe treatment of hyperthyroidism due to Graves' disease, toxic adenoma, toxic multinodular goiter. We compared the outcomes of a traditional calculation method based on an analytical fit of the uptake curve and subsequent dose calculation with the MIRD approach, and an alternative computation approach based on a formulation implemented in a public-access website, searching for the best timing of radioiodine uptake measurements in pre-therapeutic dosimetry. We report about sixty-nine hyperthyroid patients that were treated after performing a pre-therapeutic dosimetry calculated by fitting a six-point uptake curve (3-168h). In order to evaluate the results of the radioiodine treatment, patients were followed up to sixty-four months after treatment (mean 47.4±16.9). Patient dosimetry was then retrospectively recalculated with the two above-mentioned methods. Several time schedules for uptake measurements were considered, with different timings and total number of points. Early time schedules, sampling uptake up to 48h, do not allow to set-up an accurate treatment plan, while schedules including the measurement at one week give significantly better results. The analytical fit procedure applied to the three-point time schedule 3(6)-24-168h gave results significantly more accurate than the website approach exploiting either the same schedule, or the single measurement at 168h. Consequently, the best strategy among the ones considered is to sample the uptake at 3(6)-24-168h, and carry out an analytical fit of the curve, while extra measurements at 48 and 72h lead only marginal improvements in the accuracy of therapeutic activity determination. Copyright © 2016 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Oxide properties of autoclaved zircaloy cladding tubes investigated by the photoelectric polarization method

International Nuclear Information System (INIS)

Nystrand, A.C.

2000-06-01

Corrosion of zirconium alloys is an important lifetime limiting factor for the nuclear reactor fuel. The corrosion resistance of a metal is highly dependent on the ability of the surface metal oxide to transport electrons and ions, which is related to the stoichiometry of the oxide and the oxide defect concentration. The Photoelectric Polarization Method (PEP) is a structure sensitive method which earlier has been investigated as a possible method to study the defect structure in zirconium oxides. The purpose of the following work is, by using more optimized experimental equipment, to verify if the PEP method is a suitable method to study the defect structure in zirconium oxides and to predict the corrosion resistance for different zirconium alloys. The conclusions from the experiments are as follows: - The modifications of the experimental setup by means of a new source of light (deuterium lamp) and a new oscilloscope with an amplifier gave distinct Vpep signals. - The photoresponse is negative for all types of cladding and under all kind of oxidation regimes and hence the oxide is a n-type semiconductor with deficiency of oxygen. - The method needs to be verified by testing semiconductors with a known defect concentration

The zero-multipole summation method for estimating electrostatic interactions in molecular dynamics: Analysis of the accuracy and application to liquid systems

Science.gov (United States)

Fukuda, Ikuo; Kamiya, Narutoshi; Nakamura, Haruki

2014-05-01

In the preceding paper [I. Fukuda, J. Chem. Phys. 139, 174107 (2013)], the zero-multipole (ZM) summation method was proposed for efficiently evaluating the electrostatic Coulombic interactions of a classical point charge system. The summation takes a simple pairwise form, but prevents the electrically non-neutral multipole states that may artificially be generated by a simple cutoff truncation, which often causes large energetic noises and significant artifacts. The purpose of this paper is to judge the ability of the ZM method by investigating the accuracy, parameter dependencies, and stability in applications to liquid systems. To conduct this, first, the energy-functional error was divided into three terms and each term was analyzed by a theoretical error-bound estimation. This estimation gave us a clear basis of the discussions on the numerical investigations. It also gave a new viewpoint between the excess energy error and the damping effect by the damping parameter. Second, with the aid of these analyses, the ZM method was evaluated based on molecular dynamics (MD) simulations of two fundamental liquid systems, a molten sodium-chlorine ion system and a pure water molecule system. In the ion system, the energy accuracy, compared with the Ewald summation, was better for a larger value of multipole moment l currently induced until l ≲ 3 on average. This accuracy improvement with increasing l is due to the enhancement of the excess-energy accuracy. However, this improvement is wholly effective in the total accuracy if the theoretical moment l is smaller than or equal to a system intrinsic moment L. The simulation results thus indicate L ˜ 3 in this system, and we observed less accuracy in l = 4. We demonstrated the origins of parameter dependencies appearing in the crossing behavior and the oscillations of the energy error curves. With raising the moment l we observed, smaller values of the damping parameter provided more accurate results and smoother

Prevalence and clinical significance of cathepsin G antibodies in systemic sclerosis

Directory of Open Access Journals (Sweden)

M. Favaro

2011-09-01

Full Text Available Objectives: To evaluate the prevalence and clinical significance of cathepsin G antibodies in patients affected with systemic sclerosis (SSc, scleroderma. Methods: 115 patients affected by SSc, 55 (47,8% with diffuse scleroderma (dSSc and 60 (52,2% with limited scleroderma (lSSc, were tested for cathepsin G antibodies by ELISA method. Moreover these sera were evaluated by indirect immunofluorescence (IIF on ethanol and formalin fixed human neutrophils. Results: By means of the ELISA method 16 (13,9% patients were found to be sera positive for anti-cathepsin G, 2 (12.5% of which showed a perinuclear fluorescence pattern (P-ANCA and 4 (25% an atypical ANCA staining, while 10 (62,5% were negative on IIF. The IIF on scleroderma sera revealed 5 (4,3% P-ANCA and 18 (15,7% atypical ANCA patterns. The anti-cathepsin G antibodies significantly prevailed in scleroderma sera (p=0.02 when their frequency was compared with that of healthy controls; while they were not significantly associated to any clinical or serological features of SSc patients. Conclusions: The anti-cathepsin G antibodies were significantly frequent in scleroderma sera; however, no clinical correlations were found. Thus, the significance of their presence in SSc still needs to be clarified.

PENGARUH KELOMPOK ACUAN TERHADAP KESADARAN DAN KONSUMSI BERAS MERAH (ORIZA NIVARA

Directory of Open Access Journals (Sweden)

Lilik Noor Yuliati

2012-07-01

Full Text Available  Several years lately, brown rice (Oryza nivara consumption has been popular as the part of healthy life style. This research aimed to analyze the reference group’s influence towards awareness and consumption of brown rice in Bogor. This research involved 130 consumer who’s choosed by snowball method. This research revealed that reference group was influenced by the motive of consumption. It also significantly related to consumer’s age. The awareness had a relationship with education level and media, but only education level that gave significant influence towards awareness. Reference group’s strength also gave an influence, that is the increasing in reference group’s strength will lessen the awareness. This can be happen because there was information overload perceived by consumer. The brown rice consumption significantly related to the education level, family income (socio-economic status, and awareness. However, only the awareness that was significantly influenced the consumption of brown rice. 

A comparison of methods for calculating population exposure estimates of daily weather for health research

Directory of Open Access Journals (Sweden)

Dear Keith BG

2006-09-01

Full Text Available Abstract Background To explain the possible effects of exposure to weather conditions on population health outcomes, weather data need to be calculated at a level in space and time that is appropriate for the health data. There are various ways of estimating exposure values from raw data collected at weather stations but the rationale for using one technique rather than another; the significance of the difference in the values obtained; and the effect these have on a research question are factors often not explicitly considered. In this study we compare different techniques for allocating weather data observations to small geographical areas and different options for weighting averages of these observations when calculating estimates of daily precipitation and temperature for Australian Postal Areas. Options that weight observations based on distance from population centroids and population size are more computationally intensive but give estimates that conceptually are more closely related to the experience of the population. Results Options based on values derived from sites internal to postal areas, or from nearest neighbour sites – that is, using proximity polygons around weather stations intersected with postal areas – tended to include fewer stations' observations in their estimates, and missing values were common. Options based on observations from stations within 50 kilometres radius of centroids and weighting of data by distance from centroids gave more complete estimates. Using the geographic centroid of the postal area gave estimates that differed slightly from the population weighted centroids and the population weighted average of sub-unit estimates. Conclusion To calculate daily weather exposure values for analysis of health outcome data for small areas, the use of data from weather stations internal to the area only, or from neighbouring weather stations (allocated by the use of proximity polygons, is too limited. The most

Significant Returns in Engagement and Performance with a Free Teaching App

Science.gov (United States)

Green, Alan

2016-01-01

Pedagogical research shows that teaching methods other than traditional lectures may result in better outcomes. However, lecture remains the dominant method in economics, likely due to high implementation costs of methods shown to be effective in the literature. In this article, the author shows significant benefits of using a teaching app for…

Dynamic contrast-enhanced magnetic resonance imaging: a non-invasive method to evaluate significant differences between malignant and normal tissue

International Nuclear Information System (INIS)

Rudisch, Ansgar; Kremser, Christian; Judmaier, Werner; Zunterer, Hildegard; DeVries, Alexander F.

2005-01-01

Purpose: An ever recurring challenge in diagnostic radiology is the differentiation between non-malignant and malignant tissue. Based on evidence that microcirculation of normal, non-malignant tissue differs from that of malignant tissue, the goal of this study was to assess the reliability of dynamic contrast-enhanced Magnetic Resonance Imaging (dcMRI) for differentiating these two entities. Materials and methods: DcMRI data of rectum carcinoma and gluteus maximus muscles were acquired in 41 patients. Using an fast T1-mapping sequence on a 1.5-T whole body scanner, T1-maps were dynamically retrieved before, during and after constant rate i.v. infusion of a contrast medium (CM). On the basis of the acquired data sets, PI-values were calculated on a pixel-by-pixel basis. The relevance of spatial heterogeneities of microcirculation was investigated by relative frequency histograms of the PI-values. Results: A statistically significant difference between malignant and normal tissue was found for the mean PI-value (P < 0.001; 8.95 ml/min/100 g ± 2.45 versus 3.56 ml/min/100 g ± 1.20). Additionally relative frequency distributions of PI-values with equal class intervals of 2.5 ml/min/100 g revealed significant differences between the histograms of muscles and rectum carcinoma. Conclusion: We could show that microcirculation differences between malignant and normal, non-malignant tissue can be reliably assessed by non-invasive dcMRI. Therefore, dcMRI holds great promise in the aid of cancer assessment, especially in patients where biopsy is contraindicated

Diagnosis of mold allergy by RAST and skin prick testing.

Science.gov (United States)

Nordvall, S L; Agrell, B; Malling, H J; Dreborg, S

1990-11-01

Sera from 33 patients with mold allergy proven by bronchial provocation were analyzed for specific IgE against six mold species comparing an improved Phadebas RAST with four other techniques. The new method was more sensitive and gave significantly higher IgE antibody concentrations for all tested molds except Cladosporium herbarum.

Comparative-historical method in Slavic linguistics and Alexander Vostokov’s philological intuitions

Directory of Open Access Journals (Sweden)

Melkov Andrey Sergeevich

2015-04-01

Full Text Available The article is devoted to the estimation of Alexander Vostokov’s (1781-1864 contribution to the formation and development of the Slavic philology as a scientific discipline. In the foundation of the research there is the analyses of Vostokov’s work “Judgement about the Slavic language”, which has become the result of the scientist’s study the oldest Russian manuscript “Ostromir Gospels”. Vostokov devised a new method for the Slavic philology, which is used to call comparative-historical in modern science. The scientist gave the beginning of Old Church Slavonic and Old Russian written monuments scientific researching. Thanks to Vostokov’s discoveries, there has been formed the basis of Russian comparative-historical linguistics.

Inventory control of raw material using silver meal heuristic method in PR. Trubus Alami Malang

Science.gov (United States)

Ikasari, D. M.; Lestari, E. R.; Prastya, E.

2018-03-01

The purpose of this study was to compare the total inventory cost calculated using the method applied by PR. Trubus Alami and Silver Meal Heuristic (SMH) method. The study was started by forecasting the cigarette demand from July 2016 to June 2017 (48 weeks) using additive decomposition forecasting method. The additive decomposition was used because it has the lowest value of Mean Abosolute Deviation (MAD) and Mean Squared Deviation (MSD) compared to other methods such as multiplicative decomposition, moving average, single exponential smoothing, and double exponential smoothing. The forcasting results was then converted as a raw material needs and further calculated using SMH method to obtain inventory cost. As expected, the result shows that the order frequency of using SMH methods was smaller than that of using the method applied by Trubus Alami. This affected the total inventory cost. The result suggests that using SMH method gave a 29.41% lower inventory cost, giving the cost different of IDR 21,290,622. The findings, is therefore, indicated that the PR. Trubus Alami should apply the SMH method if the company wants to reduce the total inventory cost.

Mixed-methods designs in mental health services research: a review.

Science.gov (United States)

Palinkas, Lawrence A; Horwitz, Sarah M; Chamberlain, Patricia; Hurlburt, Michael S; Landsverk, John

2011-03-01

Despite increased calls for use of mixed-methods designs in mental health services research, how and why such methods are being used and whether there are any consistent patterns that might indicate a consensus about how such methods can and should be used are unclear. Use of mixed methods was examined in 50 peer-reviewed journal articles found by searching PubMed Central and 60 National Institutes of Health (NIH)-funded projects found by searching the CRISP database over five years (2005-2009). Studies were coded for aims and the rationale, structure, function, and process for using mixed methods. A notable increase was observed in articles published and grants funded over the study period. However, most did not provide an explicit rationale for using mixed methods, and 74% gave priority to use of quantitative methods. Mixed methods were used to accomplish five distinct types of study aims (assess needs for services, examine existing services, develop new or adapt existing services, evaluate services in randomized controlled trials, and examine service implementation), with three categories of rationale, seven structural arrangements based on timing and weighting of methods, five functions of mixed methods, and three ways of linking quantitative and qualitative data. Each study aim was associated with a specific pattern of use of mixed methods, and four common patterns were identified. These studies offer guidance for continued progress in integrating qualitative and quantitative methods in mental health services research consistent with efforts by NIH and other funding agencies to promote their use.

Impact significance determination-Designing an approach

International Nuclear Information System (INIS)

Lawrence, David P.

2007-01-01

The question of how best to go about determining the significance of impacts has, to date, only been addressed in a partial and preliminary way. The assumption tends to be made that it is either only necessary to provide explicit, justified reasons for a judgment about significance and/or to explicitly apply a prescribed procedure-a procedure usually involving the staged application of thresholds and/or criteria. The detailed attributes, strengths and limitations of such approaches and possible alternative approaches have yet to be explored systematically. This article addresses these deficiencies by analyzing the characteristics, specific methods and positive and negative tendencies of three general impact significance determination approaches-the technical approach, the collaborative approach and the reasoned argumentation approach. A range of potential composite approaches are also described. With an enhanced understanding of these approaches, together with potential combinations, EIA practitioners and other EIA participants can be in a better position to select an approach appropriate to their needs, to reinforce the positive tendencies and offset the negative tendencies of the selected approach and to combine the best qualities of more than one approach

Histological staining methods preparatory to laser capture microdissection significantly affect the integrity of the cellular RNA

OpenAIRE

Wang, Hongyang; Owens, James D; Shih, Joanna H; Li, Ming-Chung; Bonner, Robert F; Mushinski, J Frederic

2006-01-01

Abstract Background Gene expression profiling by microarray analysis of cells enriched by laser capture microdissection (LCM) faces several technical challenges. Frozen sections yield higher quality RNA than paraffin-imbedded sections, but even with frozen sections, the staining methods used for histological identification of cells of interest could still damage the mRNA in the cells. To study the contribution of staining methods to degradation of results from gene expression profiling of LCM...

Developing a New Sampling And Analysis Method For Hydrazine And Monomethyl Hydrazine: Using a Derivatizing Agent With Solid Phase Microextraction

Science.gov (United States)

Allen, John

2001-01-01

Solid phase microextraction (SPME) will be used to develop a method for detecting monomethyl hydrazine (MMH) and hydrazine (Hz). A derivatizing agent, pentafluorobenzoyl chloride (PFBCI), is known to react readily with MMH and Hz. The SPME fiber can either be coated with PFBCl and introduced into a gaseous stream containing MMH, or PFBCl and MMH can react first in a syringe barrel and after a short equilibration period a SPME is used to sample the resulting solution. These methods were optimized and compared. Because Hz and MMH can degrade the SPME, letting the reaction occur first gave better results. Only MMH could be detected using either of these methods. Future research will concentrate on constructing calibration curves and determining the detection limit.

Using mixed-methods research to study the quality of life of coeliac women.

Science.gov (United States)

Rodríguez Almagro, Julián; Hernández Martínez, Antonio; Solano Ruiz, María Carmen; Siles González, José

2017-04-01

To research the quality of life of Spanish women with coeliac disease. Women with coeliac disease express lower quality of life than men with coeliac disease. Explanatory sequential approach using mixed methods and with a gender perspective. The research was carried out between May and July 2015. In its quantitative stage, it aimed to determine the health-related quality of life in a representative sample (n = 1097) of Spanish adult women with coeliac disease using a specific questionnaire named Coeliac Disease-Quality of Life. In its qualitative phase, it aimed to describe the life experiences of a woman with coeliac disease in a qualitative manner by means of interviews (n = 19) with a semistructured script. Quantitative data were analysed using spss version 20 and presented in descriptive statistics. Qualitative data were analysed using the directed content analysis. The quantitative process gave us the values on the four aspects studied: dysphoria, disease limitations, health problems and inadequate treatment. These aspects allowed us to create a qualitative process, based on which we generated an interview, from which four larger categories emerged. These categories were feelings at diagnosis, limitations in day-to-day life, social perceptions of the disease and personal meanings of coeliac disease. Thus, both phases of our project are totally connected. There was a high level of congruence between quantitative scores and narratives. This study shows us the strong points of mixed-methods strategy in health sciences. The mixed-methods strategy gave us a wider view of the experience of women living with coeliac disease. In our case, a strength and not a limitation is having performed the quality of life study in women with coeliac disease using a mixed methodology, approaching the experience of being a woman with coeliac disease in Spain in two different but complementary ways. The quantitative and qualitative data allowed us to interpret the experiences of

The study of thin film growth by using Monte Carlo method

International Nuclear Information System (INIS)

Tandogan, M.; Aktas, S.

2010-01-01

Thin film growth was studied by using Monte Carlo simulation method. Three basic models were used in this study. Model A, the gas particles used for the formation of film were under no external effects until they stick on the surface or to another particle which already stickled on the surface to form the film. Model B, gases were drifted towards the surface by an external agent. Model C, where the gas particles in the closed container were always distributed uniformly throughout the container while they are in gas state. The simulations revealed the fact that for an ideal thin film growth Model C gave the best result to prepare a thin film while a thicker but a better quality could be obtained by Model B.

New patient-controlled abdominal compression method in radiography: radiation dose and image quality.

Science.gov (United States)

Piippo-Huotari, Oili; Norrman, Eva; Anderzén-Carlsson, Agneta; Geijer, Håkan

2018-05-01

The radiation dose for patients can be reduced with many methods and one way is to use abdominal compression. In this study, the radiation dose and image quality for a new patient-controlled compression device were compared with conventional compression and compression in the prone position . To compare radiation dose and image quality of patient-controlled compression compared with conventional and prone compression in general radiography. An experimental design with quantitative approach. After obtaining the approval of the ethics committee, a consecutive sample of 48 patients was examined with the standard clinical urography protocol. The radiation doses were measured as dose-area product and analyzed with a paired t-test. The image quality was evaluated by visual grading analysis. Four radiologists evaluated each image individually by scoring nine criteria modified from the European quality criteria for diagnostic radiographic images. There was no significant difference in radiation dose or image quality between conventional and patient-controlled compression. Prone position resulted in both higher dose and inferior image quality. Patient-controlled compression gave similar dose levels as conventional compression and lower than prone compression. Image quality was similar with both patient-controlled and conventional compression and was judged to be better than in the prone position.

The significance and perspectives of role playing as a teaching method in process oriented nursing education

OpenAIRE

小松, 万喜子; 冨岡, 詔子; 山崎, 章恵; 柳澤, 節子; 百瀬, 由美子

1999-01-01

This study was to report the results of students' responses to role playing which has been introduced as a teaching method in adult nursing clinical practice. About 80% of 79 students participated, positively evaluated their experiences in role playing as useful to their clinical practice, with 20% claiming negatively as not useful. An overall result suggested the usefulness of role playing as a method to enhance students' general readiness to their clinical practice. As students with negativ...

Biogas Production from Rice Husk Waste by using Solid State Anaerobic Digestion (SSAD Method

Directory of Open Access Journals (Sweden)

Hawali Abdul Matin Hashfi

2018-01-01

Full Text Available An effort to obtain alternative energy is still interesting subject to be studied, especially production of biogas from agriculture waste. This paper was an overview of the latest development of biogas researches from rice husk waste by Solid State Anaerobic Digestion (SSAD. The main obstacle of biogas production from rice husk waste was the lignin content which is very difficult degraded by microbes. Various pretreatments have been conducted, either physically, chemically as well as biologically. The SSAD method was an attractive option because of the low water content of rice husk waste. The biogas yield by SSAD method gave more attractive result compared to Liquid Anaerobic Digestion (LAD method. Various studies were still conducted in batch mode laboratory scale and also has not found optimum operating conditions. Research on a larger scale such as bench and pilot scale with continuous systems will be an increase trend in the future research.

Detecting significant changes in protein abundance

Directory of Open Access Journals (Sweden)

Kai Kammers

2015-06-01

Full Text Available We review and demonstrate how an empirical Bayes method, shrinking a protein's sample variance towards a pooled estimate, leads to far more powerful and stable inference to detect significant changes in protein abundance compared to ordinary t-tests. Using examples from isobaric mass labelled proteomic experiments we show how to analyze data from multiple experiments simultaneously, and discuss the effects of missing data on the inference. We also present easy to use open source software for normalization of mass spectrometry data and inference based on moderated test statistics.

Comparison of different methods in estimating potential evapotranspiration at Muda Irrigation Scheme of Malaysia

Directory of Open Access Journals (Sweden)

Sobri Harun

2012-04-01

Full Text Available Evapotranspiration (ET is a complex process in the hydrological cycle that influences the quantity of runoff and thus the irrigation water requirements. Numerous methods have been developed to estimate potential evapotranspiration (PET. Unfortunately, most of the reliable PET methods are parameter rich models and therefore, not feasible for application in data scarce regions. On the other hand, accuracy and reliability of simple PET models vary widely according to regional climate conditions. The objective of the present study was to evaluate the performance of three temperature-based and three radiation-based simple ET methods in estimating historical ET and projecting future ET at Muda Irrigation Scheme at Kedah, Malaysia. The performance was measured by comparing those methods with the parameter intensive Penman-Monteith Method. It was found that radiation based methods gave better performance compared to temperature-based methods in estimation of ET in the study area. Future ET simulated from projected climate data obtained through statistical downscaling technique also showed that radiation-based methods can project closer ET values to that projected by Penman-Monteith Method. It is expected that the study will guide in selecting suitable methods for estimating and projecting ET in accordance to availability of meteorological data.

Clinical significance of the fabella

International Nuclear Information System (INIS)

Dodevski, A.; Lazarova-Tosovska, D.; Zhivadinovik, J.; Lazareska, M.

2012-01-01

Full text: Introduction: There is variable number of sesamoid bones in the human body; one of them is fabella, located in the tendon of the gastrocnemius muscle. Aim of this study was to investigate the frequency of occurrence of fabella in the Macedonian population and to discuss about clinical importance of this bone. Materials and methods: We retrospectively examined radiographs of 53 patients who had knee exams undertaken for a variety of clinical reasons, performed as a part of their medical treatment. Over a time span of six months, 53 patients (38 males and 15 females, age range 19-60 years, mean age of 36.7±12.3 years) were examined. Results: In seven (13.2%) patients of 53 analyzed reports, fabella was found in the lateral tendon of gastrocnemius muscle. We did not find a significant gender or side difference in the appearance of fabella. Conclusion: Although anatomic studies emphasized a lack of significance of the fabella, this bone has been associated with a spectrum of pathology affecting the knee as fabellar syndrome, perineal nerve injury and fracture. We should think of this sesamoid bone while performing diagnostic and surgical procedures

Comparative study on diagonal equivalent methods of masonry infill panel

Science.gov (United States)

Amalia, Aniendhita Rizki; Iranata, Data

2017-06-01

ratio of height to width of 1 to 1.5. Load used in the experiment was based on Uniform Building Code (UBC) 1991. Every method compared was calculated first to get equivalent diagonal strut width. The second step was modelling method using structure analysis software as a frame with a diagonal in a linear mode. The linear mode was chosen based on structure analysis commonly used by structure designers. The frame was loaded and for every model, its load and deformation values were identified. The values of load - deformation of every method were compared to those of experimental test specimen by Mehrabi and open frame. From comparative study performed, Holmes' and Bazan-Meli's equations gave results the closest to the experimental test specimen by Mehrabi. Other equations that gave close values within the limit (by comparing it to the open frame) are Saneinejad-Hobbs, Stafford-Smith, Bazan-Meli, Liauw Kwan, Paulay and Priestley, FEMA 356, Durani Luo, Hendry, Papia and Chen-Iranata.

Rapid, convenient method for screening imidazole-containing compounds for heme oxygenase inhibition.

Science.gov (United States)

Vlahakis, Jason Z; Rahman, Mona N; Roman, Gheorghe; Jia, Zongchao; Nakatsu, Kanji; Szarek, Walter A

2011-01-01

Sensitive assays for measuring heme oxygenase activity have been based on the gas-chromatographic detection of carbon monoxide using elaborate, expensive equipment. The present study describes a rapid and convenient method for screening imidazole-containing candidates for inhibitory activity against heme oxygenase using a plate reader, based on the spectroscopic evaluation of heme degradation. A PowerWave XS plate reader was used to monitor the absorbance (as a function of time) of heme bound to purified truncated human heme oxygenase-1 (hHO-1) in the individual wells of a standard 96-well plate (with or without the addition of a test compound). The degradation of heme by heme oxygenase-1 was initiated using l-ascorbic acid, and the collected relevant absorbance data were analyzed by three different methods to calculate the percent control activity occurring in wells containing test compounds relative to that occurring in control wells with no test compound present. In the cases of wells containing inhibitory compounds, significant shifts in λ(max) from 404 to near 412 nm were observed as well as a decrease in the rate of heme degradation relative to that of the control. Each of the three methods of data processing (overall percent drop in absorbance over 1.5h, initial rate of reaction determined over the first 5 min, and estimated pseudo first-order reaction rate constant determined over 1.5h) gave similar and reproducible results for percent control activity. The fastest and easiest method of data analysis was determined to be that using initial rates, involving data acquisition for only 5 min once reactions have been initiated using l-ascorbic acid. The results of the study demonstrate that this simple assay based on the spectroscopic detection of heme represents a rapid, convenient method to determine the relative inhibitory activity of candidate compounds, and is useful in quickly screening a series or library of compounds for heme oxygenase inhibition

Gastric antral vascular ectasia and its clinical correlates in patients with early diffuse systemic sclerosis in the SCOT trial.

Science.gov (United States)

Hung, Emily W; Mayes, Maureen D; Sharif, Roozbeh; Assassi, Shervin; Machicao, Victor I; Hosing, Chitra; St Clair, E William; Furst, Daniel E; Khanna, Dinesh; Forman, Stephen; Mineishi, Shin; Phillips, Kristine; Seibold, James R; Bredeson, Christopher; Csuka, Mary Ellen; Nash, Richard A; Wener, Mark H; Simms, Robert; Ballen, Karen; Leclercq, Sharon; Storek, Jan; Goldmuntz, Ellen; Welch, Beverly; Keyes-Elstein, Lynette; Castina, Sharon; Crofford, Leslie J; Mcsweeney, Peter; Sullivan, Keith M

2013-04-01

To describe the prevalence and clinical correlates of endoscopic gastric antral vascular ectasia (GAVE; "watermelon stomach") in early diffuse systemic sclerosis (SSc). Subjects with early, diffuse SSc and evidence of specific internal organ involvement were considered for the Scleroderma: Cyclophosphamide Or Transplant (SCOT) trial. In the screening procedures, all patients underwent upper gastrointestinal endoscopy. Patients were then categorized into those with or without endoscopic evidence of GAVE. Demographic data, clinical disease characteristics, and autoantibody data were compared using Pearson chi-square or Student t tests. Twenty-three of 103 (22.3%) individuals were found to have GAVE on endoscopy. Although not statistically significant, anti-topoisomerase I (anti-Scl70) was detected less frequently among those with GAVE (18.8% vs 44.7%; p = 0.071). Similarly, anti-RNP antibodies (anti-U1 RNP) showed a trend to a negative association with GAVE (0 vs 18.4%; p = 0.066). There was no association between anti-RNA polymerase III and GAVE. Patients with GAVE had significantly more erythema or vascular ectasias in other parts of the stomach (26.1% vs 5.0%; p = 0.003). Endoscopic GAVE was present on screening in almost one-fourth of these highly selected patients with early and severe diffuse SSc. While anti-Scl70 and anti-U1 RNP trended toward a negative association with GAVE, there was no correlation between anti-RNA Pol III and GAVE. Patients with GAVE had a higher frequency of other gastric vascular ectasias outside the antrum, suggesting that GAVE may represent part of the spectrum of the vasculopathy in SSc.

Analysis of the sorption properties of different soils using water vapour adsorption and potentiometric titration methods

Science.gov (United States)

Skic, Kamil; Boguta, Patrycja; Sokołowska, Zofia

2016-07-01

Parameters of specific surface area as well as surface charge were used to determine and compare sorption properties of soils with different physicochemical characteristics. The gravimetric method was used to obtain water vapour isotherms and then specific surface areas, whereas surface charge was estimated from potentiometric titration curves. The specific surface area varied from 12.55 to 132.69 m2 g-1 for Haplic Cambisol and Mollic Gleysol soil, respectively, and generally decreased with pH (R=0.835; α = 0.05) and when bulk density (R=-0.736; α = 0.05) as well as ash content (R=-0.751; α = 0.05) increased. In the case of surface charge, the values ranged from 63.00 to 844.67 μmol g-1 Haplic Fluvisol and Mollic Gleysol, respecively. Organic matter gave significant contributions to the specific surface area and cation exchange capacity due to the large surface area and numerous surface functional groups, containing adsorption sites for water vapour molecules and for ions. The values of cation exchange capacity and specific surface area correlated linearly at the level of R=0.985; α = 0.05.

Significantly improving nuclear resonance fluorescence non-destructive assay by using the integral resonance transmission method and photofission

International Nuclear Information System (INIS)

Angell, Christopher T.; Hayakawa, Takehito; Shizuma, Toshiyuki; Hajima, Ryoichi

2013-01-01

Non-destructive assay (NDA) of 239 Pu in spent nuclear fuel or melted fuel using a γ-ray beam is possible using self absorption and the integral resonance transmission method. The method uses nuclear resonance absorption where resonances in 239 Pu remove photons from the beam, and the selective absorption is detected by measuring the decrease in scattering in a witness target placed in the beam after the fuel, consisting of the isotope of interest, namely 239 Pu. The method is isotope specific, and can use photofission or scattered γ-rays to assay the 239 Pu. It overcomes several problems related to NDA of melted fuel, including the radioactivity of the fuel, and the unknown composition and geometry. This talk will explain the general method, and how photofission can be used to assay specific isotopes, and present example calculations. (author)

Quantification of total phosphorothioate in bacterial DNA by a bromoimane-based fluorescent method.

Science.gov (United States)

Xiao, Lu; Xiang, Yu

2016-06-01

The discovery of phosphorothioate (PT) modifications in bacterial DNA has challenged our understanding of conserved phosphodiester backbone structure of cellular DNA. This exclusive DNA modification in bacteria is not found in animal cells yet, and its biological function in bacteria is still poorly understood. Quantitative information about the bacterial PT modifications is thus important for the investigation of their possible biological functions. In this study, we have developed a simple fluorescence method for selective quantification of total PTs in bacterial DNA, based on fluorescent labeling of PTs and subsequent release of the labeled fluorophores for absolute quantification. The method was highly selective to PTs and not interfered by the presence of reactive small molecules or proteins. The quantification of PTs in an E. coli DNA sample was successfully achieved using our method and gave a result of about 455 PTs per million DNA nucleotides, while almost no detectable PTs were found in a mammalian calf thymus DNA. With this new method, the content of phosphorothioate in bacterial DNA could be successfully quantified, serving as a simple method suitable for routine use in biological phosphorothioate related studies. Copyright © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Three Years Experience of Third Year Undergraduate Medical Students in Different Teaching Learning Methods: A Qualitative Study

Directory of Open Access Journals (Sweden)

Ariarathinam Newtonraj

2017-10-01

Full Text Available Introduction: India is a second largest populous country producing more than sixty thousand doctors every year. Still in India research on teaching learning methods are subtle. To improve the quality of knowledge and skills of medical students, there is a need to analyse the existing teaching learning methods as well as innovating new methods. Aim: To compare the three years experience of third year MBBS (Bachelor of Medicine and Bachelor of Surgery students in three different teaching learning methods (Tutorials, Integrated Teaching sessions and Routine Lectures. Materials and Methods: Qualitative study was carried out among 60 third year MBBS students in medical college in south India. A semi-structured questionnaire was developed, with the help of literature review and is distributed among 66 students. Six participants excluded due to incomplete information. Questionnaire consisted of totally 16 questions. For the first ten questions answers were captured in Likert scale of one to five (one-poor; five- excellent. Eleventh to sixteenth questions were asked as an open-ended question to mention some positive and negative things about each method. Questions with Likert scale were analysed using Kruskal Wallis H Test and the open ended questions were analysed by thematic analysis. Results: Overall mean rank for Tutorial was 129.03 followed by Integrated Teaching (mean rank 86.33 and Routine Lecture (mean rank 56.14. Students gave better scores for Tutorials in areas such as easily understandable, better attention span and students involvement in the session. Students gave better scoring for Integrated Teaching in areas such as well organized, integration with other departments, ideal usage of audio visual aids and providing detailed information to the students. Drawbacks of Integrated Teaching were failure to attract the students, prolonged sessions (long duration, boring and minimal involvement of students. Lecture classes on the other hand

Significant wave height retrieval from synthetic radar images

NARCIS (Netherlands)

Wijaya, Andreas Parama; van Groesen, Embrecht W.C.

2014-01-01

In many offshore activities radar imagery is used to observe and predict ocean waves. An important issue in analyzing the radar images is to resolve the significant wave height. Different from 3DFFT methods that use an estimate related to the square root of the signal-to-noise ratio of radar images,

Tune measurement at GSI SIS-18. Methods and applications

Energy Technology Data Exchange (ETDEWEB)

Singh, Rahul

2014-05-15

parameters,thus leaving out no ''free parameters''. Several important results were established in course of these experiments. Coherent tune shifts in dependence of intensity gave direct measurements of transverse machine impedances. The high resolution tune spectrum allowed identification of higher order head-tail modes. The relative spectral positions of these head-tail modes when compared with the analytical theory based on the ''square well airbag model'' gave a direct measurement of the incoherent tune spread in bunched beams. The measurements agreed well with the perturbative treatment applied in the theory only for space charge parameter in the range q{sub sc} significant deviations from the theoretical predictions occur. These deviations were understood by using self-consistent simulations and are attributed to the unaccounted role of the pipe impedances in Landau damping of head-tail modes. A novel chromaticity measurement method is demonstrated using temporal separation of each head-tail mode using chirp excitation. Other applications of the parallel tune measurement systems such as linear betatron coupling measurements or tune measurements during acceleration ramps are demonstrated. This work forms a basis for understanding beam dynamics at GSI SIS-18 for high beam currents.

Genome-wide identification of significant aberrations in cancer genome.

Science.gov (United States)

Yuan, Xiguo; Yu, Guoqiang; Hou, Xuchu; Shih, Ie-Ming; Clarke, Robert; Zhang, Junying; Hoffman, Eric P; Wang, Roger R; Zhang, Zhen; Wang, Yue

2012-07-27

Somatic Copy Number Alterations (CNAs) in human genomes are present in almost all human cancers. Systematic efforts to characterize such structural variants must effectively distinguish significant consensus events from random background aberrations. Here we introduce Significant Aberration in Cancer (SAIC), a new method for characterizing and assessing the statistical significance of recurrent CNA units. Three main features of SAIC include: (1) exploiting the intrinsic correlation among consecutive probes to assign a score to each CNA unit instead of single probes; (2) performing permutations on CNA units that preserve correlations inherent in the copy number data; and (3) iteratively detecting Significant Copy Number Aberrations (SCAs) and estimating an unbiased null distribution by applying an SCA-exclusive permutation scheme. We test and compare the performance of SAIC against four peer methods (GISTIC, STAC, KC-SMART, CMDS) on a large number of simulation datasets. Experimental results show that SAIC outperforms peer methods in terms of larger area under the Receiver Operating Characteristics curve and increased detection power. We then apply SAIC to analyze structural genomic aberrations acquired in four real cancer genome-wide copy number data sets (ovarian cancer, metastatic prostate cancer, lung adenocarcinoma, glioblastoma). When compared with previously reported results, SAIC successfully identifies most SCAs known to be of biological significance and associated with oncogenes (e.g., KRAS, CCNE1, and MYC) or tumor suppressor genes (e.g., CDKN2A/B). Furthermore, SAIC identifies a number of novel SCAs in these copy number data that encompass tumor related genes and may warrant further studies. Supported by a well-grounded theoretical framework, SAIC has been developed and used to identify SCAs in various cancer copy number data sets, providing useful information to study the landscape of cancer genomes. Open-source and platform-independent SAIC software is

Different methods for quark/gluon jet classification on real data from the DELPHI detector

Energy Technology Data Exchange (ETDEWEB)

Transtroemer, G

1999-05-01

Different methods to separate quark jets from gluon jets have been investigated and tested on data from the DELPHI experiment. A test sample of gluon jets was selected from bb-barg threejet events where the two b-jets had been identified using a lifetime tag and quark jet sample was obtained from qq-bar{gamma} events where the photon was required to have a high energy and to be well separated from the two jets. Three types of tests were made. Firstly, the jet energy, which is the variable most frequently used for quark/gluon jet separation, was compared with methods based of the differences in the fragmentation of quark and gluon jets. It was found that the fragmentation based classification provides significantly better identification than the jet energy only in events where the jets all have approximately the same energy. In Monte Carlo generated symmetric e{sup +}e{sup -} {yields} qq-barg threejet events, where the jet energy does not provide any identification at all, the gluon jet was correctly assigned in 58 % of the events. More important, however, is that the identification has been divided into two independent parts, the energy part and the fragmentation part. Secondly, two different sets of fragmentation sensitive variables were tested. It was found that a slightly better identification could be achieved using information from all the particles of the jet rather than using only the leading ones. Thirdly, three types of statistical discrimination methods were compared: a cut on a single fragmentation variable; a cut on the Fisher statistical discriminant calculated from one set of variables; a cut on the output from an Artificial Neural Networks (ANN) trained on different sets of variables. The three types of classifiers gave about the same performance and one conclusion from this study was that the use of ANNs or Fisher statistical discrimination do not seem to improve the results significantly in quark/gluon jet separation on a jet to jet basis 45 refs

Different methods for quark/gluon jet classification on real data from the DELPHI detector

International Nuclear Information System (INIS)

Transtroemer, G.

1999-05-01

Different methods to separate quark jets from gluon jets have been investigated and tested on data from the DELPHI experiment. A test sample of gluon jets was selected from bb-barg threejet events where the two b-jets had been identified using a lifetime tag and quark jet sample was obtained from qq-barγ events where the photon was required to have a high energy and to be well separated from the two jets. Three types of tests were made. Firstly, the jet energy, which is the variable most frequently used for quark/gluon jet separation, was compared with methods based of the differences in the fragmentation of quark and gluon jets. It was found that the fragmentation based classification provides significantly better identification than the jet energy only in events where the jets all have approximately the same energy. In Monte Carlo generated symmetric e + e - → qq-barg threejet events, where the jet energy does not provide any identification at all, the gluon jet was correctly assigned in 58 % of the events. More important, however, is that the identification has been divided into two independent parts, the energy part and the fragmentation part. Secondly, two different sets of fragmentation sensitive variables were tested. It was found that a slightly better identification could be achieved using information from all the particles of the jet rather than using only the leading ones. Thirdly, three types of statistical discrimination methods were compared: a cut on a single fragmentation variable; a cut on the Fisher statistical discriminant calculated from one set of variables; a cut on the output from an Artificial Neural Networks (ANN) trained on different sets of variables. The three types of classifiers gave about the same performance and one conclusion from this study was that the use of ANNs or Fisher statistical discrimination do not seem to improve the results significantly in quark/gluon jet separation on a jet to jet basis

Significance and radioimmunoassay of gastric inhibitory polypeptide

International Nuclear Information System (INIS)

Zheng Ping; Zeng Minde; Yuan Jimin

1995-01-01

We have established the GIP Radioimmunoassay which has high sensitivity and specificity by labelling with iodogen and purified with HPLC. Using this method, the plasma GIP level was measured in 64 cases of which there are 10 normal individuals, 25 cases of diabetes and 29 cases of liver cirrhosis . The results showed that the plasma GIP level was significantly increased in patients with liver cirrhosis and correlated to degree of glucose tolerance damage

Significance of perfectionism in understanding different forms of insomnia

Directory of Open Access Journals (Sweden)

Totić-Poznanović Sanja

2012-01-01

Full Text Available Introduction. Studies consistently show a connection between perfectionism as a multidimensional construct with various psychological and psychopathological states and characteristics. However, studies that analyze the connection between this concept and sleep disturbances, especially modalities of insomnia, are rare. Objective. The aim of this study was to examine whether dimensions of perfectionism can explain different forms of insomnia; difficulties initiating sleep (insomnia early, difficulties during the sleep (insomnia middle, waking in early hours of the morning (insomnia late and dissatisfaction with sleep quality (subjective insomnia. Methods. The sample consisted of 254 students of the School of Medicine in Belgrade. Predictive significance of nine perfectionism dimensions, measured by Frost’s and Hewitt’s and Flett’s scales of multi-dimensional perfectionism, related to four modalities of insomnia, measured by a structured questionnaire, was analyzed by multiple linear regression method. Results. Perfectionism dimensions are significant predictors of each of the tested forms of insomnia. Doubt about actions significantly predicts initial insomnia; to other-oriented perfectionism in the negative pole and socially prescribed perfectionism underlie the difficulties during the sleep, while organization and parental criticism underlie late insomnia. Significant predictors of subjective insomnia are personal standards and organization and to other-oriented perfectionism on the negative pole. Three of nine analyzed dimensions were not confirmed as significant; concern over mistakes, parental expectations and self-oriented perfectionism. Conclusion. Various aspects of perfectionism can be considered as a vulnerability factor for understanding some forms of insomnia. Out of all forms of insomnia tested, perfectionism as the personality trait proved to be the most significant for understanding subjective insomnia.

Feature selection based on SVM significance maps for classification of dementia

NARCIS (Netherlands)

E.E. Bron (Esther); M. Smits (Marion); J.C. van Swieten (John); W.J. Niessen (Wiro); S. Klein (Stefan)

2014-01-01

textabstractSupport vector machine significance maps (SVM p-maps) previously showed clusters of significantly different voxels in dementiarelated brain regions. We propose a novel feature selection method for classification of dementia based on these p-maps. In our approach, the SVM p-maps are

Validated UV-spectrophotometric method for the evaluation of the efficacy of makeup remover.

Science.gov (United States)

Charoennit, P; Lourith, N

2012-04-01

A UV-spectrophotometric method for the analysis of makeup remover was developed and validated according to ICH guidelines. Three makeup removers for which the main ingredients consisted of vegetable oil (A), mineral oil and silicone (B) and mineral oil and water (C) were sampled in this study. Ethanol was the optimal solvent because it did not interfere with the maximum absorbance of the liquid foundation at 250 nm. The linearity was determined over a range of makeup concentrations from 0.540 to 1.412 mg mL⁻¹ (R² = 0.9977). The accuracy of this method was determined by analysing low, intermediate and high concentrations of the liquid foundation and gave 78.59-91.57% recoveries with a relative standard deviation of makeup remover efficacy. © 2011 The Authors. ICS © 2011 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Evaluation of phylogenetic reconstruction methods using bacterial whole genomes: a simulation based study [version 1; referees: 1 approved, 2 approved with reservations

Directory of Open Access Journals (Sweden)

John A. Lees

2018-03-01

Full Text Available Background: Phylogenetic reconstruction is a necessary first step in many analyses which use whole genome sequence data from bacterial populations. There are many available methods to infer phylogenies, and these have various advantages and disadvantages, but few unbiased comparisons of the range of approaches have been made. Methods: We simulated data from a defined “true tree” using a realistic evolutionary model. We built phylogenies from this data using a range of methods, and compared reconstructed trees to the true tree using two measures, noting the computational time needed for different phylogenetic reconstructions. We also used real data from Streptococcus pneumoniae alignments to compare individual core gene trees to a core genome tree. Results: We found that, as expected, maximum likelihood trees from good quality alignments were the most accurate, but also the most computationally intensive. Using less accurate phylogenetic reconstruction methods, we were able to obtain results of comparable accuracy; we found that approximate results can rapidly be obtained using genetic distance based methods. In real data we found that highly conserved core genes, such as those involved in translation, gave an inaccurate tree topology, whereas genes involved in recombination events gave inaccurate branch lengths. We also show a tree-of-trees, relating the results of different phylogenetic reconstructions to each other. Conclusions: We recommend three approaches, depending on requirements for accuracy and computational time. Quicker approaches that do not perform full maximum likelihood optimisation may be useful for many analyses requiring a phylogeny, as generating a high quality input alignment is likely to be the major limiting factor of accurate tree topology. We have publicly released our simulated data and code to enable further comparisons.

Robust statistical methods for significance evaluation and applications in cancer driver detection and biomarker discovery

DEFF Research Database (Denmark)

Madsen, Tobias

2017-01-01

In the present thesis I develop, implement and apply statistical methods for detecting genomic elements implicated in cancer development and progression. This is done in two separate bodies of work. The first uses the somatic mutation burden to distinguish cancer driver mutations from passenger m...

48 CFR 815.304 - Evaluation factors and significant subfactors.

Science.gov (United States)

2010-10-01

... AFFAIRS CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Source Selection 815.304 Evaluation factors and significant subfactors. (a) In an effort to assist SDVOSBs and VOSBs, contracting officers shall include evaluation factors providing additional consideration to such offerors in...

Clinically significant change in stroke volume in pulmonary hypertension.

Science.gov (United States)

van Wolferen, Serge A; van de Veerdonk, Marielle C; Mauritz, Gert-Jan; Jacobs, Wouter; Marcus, J Tim; Marques, Koen M J; Bronzwaer, Jean G F; Heymans, Martijn W; Boonstra, Anco; Postmus, Pieter E; Westerhof, Nico; Vonk Noordegraaf, Anton

2011-05-01

Stroke volume is probably the best hemodynamic parameter because it reflects therapeutic changes and contains prognostic information in pulmonary hypertension (PH). Stroke volume directly reflects right ventricular function in response to its load, without the correction of compensatory increased heart rate as is the case for cardiac output. For this reason, stroke volume, which can be measured noninvasively, is an important hemodynamic parameter to monitor during treatment. However, the extent of change in stroke volume that constitutes a clinically significant change is unknown. The aim of this study was to determine the minimal important difference (MID) in stroke volume in PH. One hundred eleven patients were evaluated at baseline and after 1 year of follow-up with a 6-min walk test (6MWT) and cardiac MRI. Using the anchor-based method with 6MWT as the anchor, and the distribution-based method, the MID of stroke volume change could be determined. After 1 year of treatment, there was, on average, a significant increase in stroke volume and 6MWT. The change in stroke volume was related to the change in 6MWT. Using the anchor-based method, an MID of 10 mL in stroke volume was calculated. The distribution-based method resulted in an MID of 8 to 12 mL. Both methods showed that a 10-mL change in stroke volume during follow-up should be considered as clinically relevant. This value can be used to interpret changes in stroke volume during clinical follow-up in PH.

Numerical Methods for Free Boundary Problems

CERN Document Server

1991-01-01

About 80 participants from 16 countries attended the Conference on Numerical Methods for Free Boundary Problems, held at the University of Jyviiskylii, Finland, July 23-27, 1990. The main purpose of this conference was to provide up-to-date information on important directions of research in the field of free boundary problems and their numerical solutions. The contributions contained in this volume cover the lectures given in the conference. The invited lectures were given by H.W. Alt, V. Barbu, K-H. Hoffmann, H. Mittelmann and V. Rivkind. In his lecture H.W. Alt considered a mathematical model and existence theory for non-isothermal phase separations in binary systems. The lecture of V. Barbu was on the approximate solvability of the inverse one phase Stefan problem. K-H. Hoff­ mann gave an up-to-date survey of several directions in free boundary problems and listed several applications, but the material of his lecture is not included in this proceedings. H.D. Mittelmann handled the stability of thermo capi...

Analysis of residual toluene in food packaging via headspace extraction method using gas chromatography

International Nuclear Information System (INIS)

Lim, Ying Chin; Mohd Marsin Sanagi

2008-01-01

Polymeric materials are used in many food contact applications as packaging material. The presence of residual toluene in this food packaging material can migrate into food and thus affect the quality of food. In this study, a manual headspace analysis was successfully designed and developed. The determination of residual toluene was carried out with standard addition method and multiple headspace extraction, MHE) method using gas chromatography-flame ionization detector, GC-FID). Identification of toluene was performed by comparison of its retention time with standard toluene and GC-MS. It was found that the suitable heating temperature was 180 degree Celsius with an optimum heating time of 10 minutes. The study also found that the concentration of residual toluene in multicolored sample was higher compared to mono colored sample whereas residual toluene in sample analyzed using standard addition method was higher compared to MHE method. However, comparison with the results obtained from De Paris laboratory, France found that MHE method gave higher accuracy for sample with low analyte concentration. On the other hand, lower accuracy was obtained for sample with high concentration of residual toluene due to systematic errors. Comparison between determination methods showed that MHE method is more precise compared to standard addition method. (author)

Microwave and thermal pretreatment as methods for increasing the biogas potential of secondary sludge from municipal wastewater treatment plants

DEFF Research Database (Denmark)

Kuglarz, Mariusz; Karakashev, Dimitar Borisov; Angelidaki, Irini

2013-01-01

In the present study, the sludge was pretreated with microwave irradiation and low-temperature thermal method, both conducted under the same temperature range (30–100°C). Microwave pretreatment was found to be superior over the thermal treatment with respect to sludge solubilization and biogas pr...... experiments indicated that pre-treated sludge (microwave irradiation: 900W, temperature: 60–70°C) gave 35% more methane, compared to untreated sludge. Moreover, the results of this study clearly demonstrated that microwave pretreated sludge showed better degree of sanitation....

The Comparison Study of Neutron Activation Analysis and Fission Track Technique for Uranium Determination

International Nuclear Information System (INIS)

Sirinuntavid, Alice; Rodthongkom, Chouvana

2007-08-01

Full text: Comparison between Neutron Activation Analysis (NAA) and fission track technique for uranium determination in solid samples was studied by use of standard reference materials, i.e., ore, coal fly ash, soil. For NAA, the epithermal neutron was applied for activated irradiation. Then, the 74.5 keV gamma from U-239 or 277.7 keV gamma from Np-239 was measured. For high Uranium content samples, NAA method with 74.5 keV gamma measurement, gave higher precision result than the 277.7 keV gamma measurement method. NAA method with 277.7 keV gamma measurement, gave higher sensitivity and precision result for low Uranium content samples and the uranium contained less than 10 ppm samples. Nevertheless, the latter procedure needed longer time for neutron irradiation and analysis procedure. In comparison the results of Uranium analysis between NAA and fission track, it was found that no significant difference within 95 % of confidence level

Determining Semantically Related Significant Genes.

Science.gov (United States)

Taha, Kamal

2014-01-01

GO relation embodies some aspects of existence dependency. If GO term xis existence-dependent on GO term y, the presence of y implies the presence of x. Therefore, the genes annotated with the function of the GO term y are usually functionally and semantically related to the genes annotated with the function of the GO term x. A large number of gene set enrichment analysis methods have been developed in recent years for analyzing gene sets enrichment. However, most of these methods overlook the structural dependencies between GO terms in GO graph by not considering the concept of existence dependency. We propose in this paper a biological search engine called RSGSearch that identifies enriched sets of genes annotated with different functions using the concept of existence dependency. We observe that GO term xcannot be existence-dependent on GO term y, if x- and y- have the same specificity (biological characteristics). After encoding into a numeric format the contributions of GO terms annotating target genes to the semantics of their lowest common ancestors (LCAs), RSGSearch uses microarray experiment to identify the most significant LCA that annotates the result genes. We evaluated RSGSearch experimentally and compared it with five gene set enrichment systems. Results showed marked improvement.

Identification of significant features by the Global Mean Rank test.

Science.gov (United States)

Klammer, Martin; Dybowski, J Nikolaj; Hoffmann, Daniel; Schaab, Christoph

2014-01-01

With the introduction of omics-technologies such as transcriptomics and proteomics, numerous methods for the reliable identification of significantly regulated features (genes, proteins, etc.) have been developed. Experimental practice requires these tests to successfully deal with conditions such as small numbers of replicates, missing values, non-normally distributed expression levels, and non-identical distributions of features. With the MeanRank test we aimed at developing a test that performs robustly under these conditions, while favorably scaling with the number of replicates. The test proposed here is a global one-sample location test, which is based on the mean ranks across replicates, and internally estimates and controls the false discovery rate. Furthermore, missing data is accounted for without the need of imputation. In extensive simulations comparing MeanRank to other frequently used methods, we found that it performs well with small and large numbers of replicates, feature dependent variance between replicates, and variable regulation across features on simulation data and a recent two-color microarray spike-in dataset. The tests were then used to identify significant changes in the phosphoproteomes of cancer cells induced by the kinase inhibitors erlotinib and 3-MB-PP1 in two independently published mass spectrometry-based studies. MeanRank outperformed the other global rank-based methods applied in this study. Compared to the popular Significance Analysis of Microarrays and Linear Models for Microarray methods, MeanRank performed similar or better. Furthermore, MeanRank exhibits more consistent behavior regarding the degree of regulation and is robust against the choice of preprocessing methods. MeanRank does not require any imputation of missing values, is easy to understand, and yields results that are easy to interpret. The software implementing the algorithm is freely available for academic and commercial use.

AWElectric : that gave me goosebumps, did you feel it too?

NARCIS (Netherlands)

Neidlinger, K.; Truong, K.P.; Telfair, C.; Feijs, L.M.G.; Dertien, E.; Evers, V.

2017-01-01

Awe is a powerful, visceral sensation described as a sudden chill or shudder accompanied by goosebumps. People feel awe in the face of extraordinary experiences: The sublimity of nature, the beauty of art and music, the adrenaline rush of fear. Awe is healthy, both physically and mentally. It can be

AWElectric : that gave me goosebumps, did you feel it too?

NARCIS (Netherlands)

Neidlinger, Kristin; Truong, Khiet Phuong; Telfair, Caty; Feijs, Loe; Dertien, Edwin Christian; Evers, Vanessa

2017-01-01

Awe is a powerful, visceral sensation described as a sudden chill or shudder accompanied by goosebumps. People feel awe in the face of extraordinary experiences: the sublimity of nature, the beauty of art and music, the adrenaline rush of fear. Awe is healthy, both physically and mentally. It can be

The identification of provenance-controlled facies by geochemical methods on a portion of the Vaal Reef, Klerksdorp Goldfield

International Nuclear Information System (INIS)

Henckel, J.; Schweitzer, J.K.; Horsch, H.

1990-01-01

The use of geochemical methods for identifying provenance controlled facies in Witwatersrand reefs is considered. Three methods - whole rock geochemistry, zircon analysis, and chromite analysis - have been evaluated in order to establish the feasibility of using these geochemical techniques. An area of Vaal Reef where two sedimentological facies with distinct gold distributions had previously been identified was investigated. The studies reported here gave evidence of differences in the source areas for these two facies. Accordingly, it is concluded that the application of geochemistry to identify provenance-controlled facies is a useful technique which can help geologists arrive at a better interpretation of depositional systems within Witwatersrand reefs and thereby assist in the understanding of gold distribution patterns. 26 refs., 11 figs., 4 tabs

Extraction and characterization of gelatin from two edible Sudanese insects and its applications in ice cream making.

Science.gov (United States)

Mariod, Abdalbasit Adam; Fadul, Hadia

2015-07-01

Three methods were used for extraction of gelatin from two insects, melon bug (Coridius viduatus) and sorghum bug (Agonoscelis versicoloratus versicoloratus). Extraction of insect gelatin using hot water gave higher yield reached up to 3.0%, followed by mild acid extraction which gave 1.5% and distilled water extraction which gave only 1.0%, respectively. The obtained gelatins were characterized by FTIR and the spectra of insect's gelatin seem to be similar when compared with commercial gelatin. Amide II bands of gelatins from melon and sorghum bug appeared around at 1542-1537 cm(-1). Slight differences in the amino acid composition of gelatin extracted from the two insects were observed. Ice cream was made by using 0.5% insect's gelatin and compared with that made using 0.5% commercial gelatin as stabilizing agent. The properties of the obtained ice cream produced using insects gelatin were significantly different when compared with that made using commercial gelatin. © The Author(s) 2014.

Manual versus mechanical cardiopulmonary resuscitation. An experimental study in pigs

Directory of Open Access Journals (Sweden)

Wohlfart Björn

2010-10-01

Full Text Available Abstract Background Optimal manual closed chest compressions are difficult to give. A mechanical compression/decompression device, named LUCAS, is programmed to give compression according to the latest international guidelines (2005 for cardiopulmonary resuscitation (CPR. The aim of the present study was to compare manual CPR with LUCAS-CPR. Methods 30 kg pigs were anesthetized and intubated. After a base-line period and five minutes of ventricular fibrillation, manual CPR (n = 8 or LUCAS-CPR (n = 8 was started and run for 20 minutes. Professional paramedics gave manual chest compression's alternating in 2-minute periods. Ventilation, one breath for each 10 compressions, was given to all animals. Defibrillation and, if needed, adrenaline were given to obtain a return of spontaneous circulation (ROSC. Results The mean coronary perfusion pressure was significantly (p Conclusions LUCAS-CPR gave significantly higher coronary perfusion pressure and significantly fewer rib fractures than manual CPR in this porcine model.

Significance of atypical squamous cells of undetermined significance on ThinPrep papanicolaou smears.

Science.gov (United States)

Eltabbakh, G H; Lipman, J N; Mount, S L; Morgan, A

2000-10-01

The aim of this study was to assess the prevalence and risk factors predictive of dysplasia among women seen in a gynecologic oncology service with the cytologic diagnosis of atypical squamous cells of undetermined significance (ASCUS) on Papanicolaou smears obtained by the ThinPrep method. Patients with ASCUS ThinPrep Papanicolaou smears seen at the Division of Gynecologic Oncology, University of Vermont, between 1997 and 1999 were identified. The cytologic smears were reviewed and subtyped into reactive or suggestive of squamous intraepithelial lesion (SIL). The charts of these patients were reviewed and the following information was abstracted: age, gravidity, parity, menopausal status, use of hormonal replacement therapy, smoking, history of pelvic cancer, history of radiation therapy, history of abnormal Papanicolaou smear and its treatment, history of human papillomavirus (HPV) infection, and follow-up information including results of repeat Papanicolaou smears, colposcopy, and biopsies. The prevalence of dysplasia was calculated. The demographic features of women with ASCUS, reactive, were compared with those with ASCUS, SIL, using a two-sample t test, chi(2), and Fisher's exact test. Risk factors predictive of dysplasia were calculated using the odds ratio and the 95% confidence interval. P ASCUS on ThinPrep Papanicolaou smear were identified; 63 patients had ASCUS, reactive, and 63 patients had ASCUS, SIL. The demographic features of both groups were similar. The overall prevalence of dysplasia was 15.9% and was significantly higher among women with ASCUS, SIL, than among women with ASCUS, reactive (25.4% versus 6.4%, P = 0.003). The type of ASCUS cytology (reactive versus SIL), smoking, and history of HPV were significant risk factors for dysplasia (P = 0.003, 0.037, and 0. 042, respectively). The prevalence of dysplasia among women seen in a gynecologic oncology service with ASCUS cytology on ThinPrep Papanicolaou smears is 15.9%. Women with ASCUS favor

Development of a Flow Cytometry-Based Method for Rapid Detection of Escherichia coli and Shigella Spp. Using an Oligonucleotide Probe

Science.gov (United States)

Xue, Yong; Wilkes, Jon G.; Moskal, Ted J.; Williams, Anna J.; Cooper, Willie M.; Nayak, Rajesh; Rafii, Fatemeh; Buzatu, Dan A.

2016-01-01

Standard methods to detect Escherichia coli contamination in food use the polymerase chain reaction (PCR) and agar culture plates. These methods require multiple incubation steps and take a long time to results. An improved rapid flow-cytometry based detection method was developed, using a fluorescence-labeled oligonucleotide probe specifically binding a16S rRNA sequence. The method positively detected 51 E. coli isolates as well as 4 Shigella species. All 27 non-E. coli strains tested gave negative results. Comparison of the new genetic assay with a total plate count (TPC) assay and agar plate counting indicated similar sensitivity, agreement between cytometry cell and colony counts. This method can detect a small number of E.coli cells in the presence of large numbers of other bacteria. This method can be used for rapid, economical, and stable detection of E. coli and Shigella contamination in the food industry and other contexts. PMID:26913737

Development of a Flow Cytometry-Based Method for Rapid Detection of Escherichia coli and Shigella Spp. Using an Oligonucleotide Probe.

Directory of Open Access Journals (Sweden)

Yong Xue

Full Text Available Standard methods to detect Escherichia coli contamination in food use the polymerase chain reaction (PCR and agar culture plates. These methods require multiple incubation steps and take a long time to results. An improved rapid flow-cytometry based detection method was developed, using a fluorescence-labeled oligonucleotide probe specifically binding a16S rRNA sequence. The method positively detected 51 E. coli isolates as well as 4 Shigella species. All 27 non-E. coli strains tested gave negative results. Comparison of the new genetic assay with a total plate count (TPC assay and agar plate counting indicated similar sensitivity, agreement between cytometry cell and colony counts. This method can detect a small number of E.coli cells in the presence of large numbers of other bacteria. This method can be used for rapid, economical, and stable detection of E. coli and Shigella contamination in the food industry and other contexts.

Recycling of Wastewater from Swine farm and Bio-organic fertilizer for Baby Corn Cultivation

International Nuclear Information System (INIS)

Piadang, Nattayana; Palajoom, Somsak; Kumklang, Tawan; Laothamyingyong, Metinee; Sirodomsakul, Pranee

2006-09-01

The study was conducted to determine the yield of baby corn production treated with wastewater from swine farm. The experiment was set up following the Randomized Complete Block Design with 7 treatments 4 replications. The treatments were no fertilizer, chemical fertilizer, compost, liquid microbial fertilizers (LMF.) of OAP, liquid fish fertilizer (LFF.) of NM., wastewater from swine farm with biogas (SFbg.) and wastewater from swine farm without biogas (SF.). Results at harvested stage of test pot experiment revealed that plant height of liquid fish fertilizer (LFF.) except chemical fertilizer (P<0.01) and dry weight of stem showed highly significant (P<0.01), and chemical fertilizer gave the highest yield (574.76 g/pot). At the same ration of 1:200 LFF of NM and 1:50 of LMF, OAP gave the highest yield of baby corn at 383.76 and 299.88 g per pot respectively. Fresh ear weight of baby corn at harvesting gave significant different (P<0.05). LFF, NM. at the ratio of 1:20 gave the highest yield and higher than chemical fertilizer. But LMF, OAP gave the highest yield at the ratio of 1:50. Fresh ear without husk at harvesting gave highly significant difference (P<0.01), which LFF, NM gave the highest yield at the ratio of 1:200. At the same ratio of 1:50 LMF, OAP gave the highest yield of baby corn. These means that liquid microbial fertilizer of OAP gave the better choice for cheaper cost of reduction in the long term after cultivation in may crops. It will promote the growth of micro-organism in soil for enhancement of soil quality.

Ion-selective electrodes in potentiometric titrations; a new method for processing and evaluating titration data.

Science.gov (United States)

Granholm, Kim; Sokalski, Tomasz; Lewenstam, Andrzej; Ivaska, Ari

2015-08-12

A new method to convert the potential of an ion-selective electrode to concentration or activity in potentiometric titration is proposed. The advantage of this method is that the electrode standard potential and the slope of the calibration curve do not have to be known. Instead two activities on the titration curve have to be estimated e.g. the starting activity before the titration begins and the activity at the end of the titration in the presence of large excess of titrant. This new method is beneficial when the analyte is in a complexed matrix or in a harsh environment which affects the properties of the electrode and the traditional calibration procedure with standard solutions cannot be used. The new method was implemented both in a method of linearization based on the Grans's plot and in determination of the stability constant of a complex and the concentration of the complexing ligand in the sample. The new method gave accurate results when using titrations data from experiments with samples of known composition and with real industrial harsh black liquor sample. A complexometric titration model was also developed. Copyright © 2015 Elsevier B.V. All rights reserved.

Application of the DC potential drop and the partial unloading methods to fracture mechanics tests

International Nuclear Information System (INIS)

Heerens, J.; Schwalbe, K.H.; Hellmann, D.; Knaack, J.; Mueller-Roos, J.

1985-01-01

The ability of the DC potential drop method and the partial unloading technique to measure crack growth and to detect initation of crack growth has been investigated using a number of steels and aluminium alloys. It was found that within the range of parameters investigated both of these methods can be recommended for the determination of the R-curve; however, since at small amounts of crack growth the DC potential drop method gave more consistent results it is therefore considered to be superior. The initation values J(0) of J determined by fractography were compared with J(Ic) as obtained by current practice. It was found that J(Ic) is poorly related to initation or to specific amount of crack growth. A modification of the J(Ic) procedure is proposed. Two contacting arrangements of the DC potential drop method were checked for initation detection: one indicates initation by a potential minimum (related to a J value J(min)), the other by the intersection of the R-curve with the blunting line (related to a J value J(int)). (orig.) [de

Assessing Mucoadhesion in Polymer Gels: The Effect of Method Type and Instrument Variables

Directory of Open Access Journals (Sweden)

Jéssica Bassi da Silva

2018-03-01

Full Text Available The process of mucoadhesion has been widely studied using a wide variety of methods, which are influenced by instrumental variables and experiment design, making the comparison between the results of different studies difficult. The aim of this work was to standardize the conditions of the detachment test and the rheological methods of mucoadhesion assessment for semisolids, and introduce a texture profile analysis (TPA method. A factorial design was developed to suggest standard conditions for performing the detachment force method. To evaluate the method, binary polymeric systems were prepared containing poloxamer 407 and Carbopol 971P®, Carbopol 974P®, or Noveon® Polycarbophil. The mucoadhesion of systems was evaluated, and the reproducibility of these measurements investigated. This detachment force method was demonstrated to be reproduceable, and gave different adhesion when mucin disk or ex vivo oral mucosa was used. The factorial design demonstrated that all evaluated parameters had an effect on measurements of mucoadhesive force, but the same was not observed for the work of adhesion. It was suggested that the work of adhesion is a more appropriate metric for evaluating mucoadhesion. Oscillatory rheology was more capable of investigating adhesive interactions than flow rheology. TPA method was demonstrated to be reproducible and can evaluate the adhesiveness interaction parameter. This investigation demonstrates the need for standardized methods to evaluate mucoadhesion and makes suggestions for a standard study design.

Genome-wide identification of significant aberrations in cancer genome

Directory of Open Access Journals (Sweden)

Yuan Xiguo

2012-07-01

Full Text Available Abstract Background Somatic Copy Number Alterations (CNAs in human genomes are present in almost all human cancers. Systematic efforts to characterize such structural variants must effectively distinguish significant consensus events from random background aberrations. Here we introduce Significant Aberration in Cancer (SAIC, a new method for characterizing and assessing the statistical significance of recurrent CNA units. Three main features of SAIC include: (1 exploiting the intrinsic correlation among consecutive probes to assign a score to each CNA unit instead of single probes; (2 performing permutations on CNA units that preserve correlations inherent in the copy number data; and (3 iteratively detecting Significant Copy Number Aberrations (SCAs and estimating an unbiased null distribution by applying an SCA-exclusive permutation scheme. Results We test and compare the performance of SAIC against four peer methods (GISTIC, STAC, KC-SMART, CMDS on a large number of simulation datasets. Experimental results show that SAIC outperforms peer methods in terms of larger area under the Receiver Operating Characteristics curve and increased detection power. We then apply SAIC to analyze structural genomic aberrations acquired in four real cancer genome-wide copy number data sets (ovarian cancer, metastatic prostate cancer, lung adenocarcinoma, glioblastoma. When compared with previously reported results, SAIC successfully identifies most SCAs known to be of biological significance and associated with oncogenes (e.g., KRAS, CCNE1, and MYC or tumor suppressor genes (e.g., CDKN2A/B. Furthermore, SAIC identifies a number of novel SCAs in these copy number data that encompass tumor related genes and may warrant further studies. Conclusions Supported by a well-grounded theoretical framework, SAIC has been developed and used to identify SCAs in various cancer copy number data sets, providing useful information to study the landscape of cancer genomes

Geometrical method of decoupling

Directory of Open Access Journals (Sweden)

C. Baumgarten

2012-12-01

Full Text Available The computation of tunes and matched beam distributions are essential steps in the analysis of circular accelerators. If certain symmetries—like midplane symmetry—are present, then it is possible to treat the betatron motion in the horizontal, the vertical plane, and (under certain circumstances the longitudinal motion separately using the well-known Courant-Snyder theory, or to apply transformations that have been described previously as, for instance, the method of Teng and Edwards. In a preceding paper, it has been shown that this method requires a modification for the treatment of isochronous cyclotrons with non-negligible space charge forces. Unfortunately, the modification was numerically not as stable as desired and it was still unclear, if the extension would work for all conceivable cases. Hence, a systematic derivation of a more general treatment seemed advisable. In a second paper, the author suggested the use of real Dirac matrices as basic tools for coupled linear optics and gave a straightforward recipe to decouple positive definite Hamiltonians with imaginary eigenvalues. In this article this method is generalized and simplified in order to formulate a straightforward method to decouple Hamiltonian matrices with eigenvalues on the real and the imaginary axis. The decoupling of symplectic matrices which are exponentials of such Hamiltonian matrices can be deduced from this in a few steps. It is shown that this algebraic decoupling is closely related to a geometric “decoupling” by the orthogonalization of the vectors E[over →], B[over →], and P[over →], which were introduced with the so-called “electromechanical equivalence.” A mathematical analysis of the problem can be traced down to the task of finding a structure-preserving block diagonalization of symplectic or Hamiltonian matrices. Structure preservation means in this context that the (sequence of transformations must be symplectic and hence canonical. When

Method Development in the Regioselective Glycosylation of Unprotected Carbohydrates

DEFF Research Database (Denmark)

Niedbal, Dominika Alina

and the glycosylations were promoted by tetrabutylammonium bromide. The couplings were completely selective and gave rise to a number of 1,6-linked disaccharides with 1,2- cis-linked orientation. Project 2: Boron-mediated glycosylation of unprotected carbohydrates Boron-mediated regioselective Koenigs...

Significance testing in ridge regression for genetic data

Directory of Open Access Journals (Sweden)

De Iorio Maria

2011-09-01

Full Text Available Abstract Background Technological developments have increased the feasibility of large scale genetic association studies. Densely typed genetic markers are obtained using SNP arrays, next-generation sequencing technologies and imputation. However, SNPs typed using these methods can be highly correlated due to linkage disequilibrium among them, and standard multiple regression techniques fail with these data sets due to their high dimensionality and correlation structure. There has been increasing interest in using penalised regression in the analysis of high dimensional data. Ridge regression is one such penalised regression technique which does not perform variable selection, instead estimating a regression coefficient for each predictor variable. It is therefore desirable to obtain an estimate of the significance of each ridge regression coefficient. Results We develop and evaluate a test of significance for ridge regression coefficients. Using simulation studies, we demonstrate that the performance of the test is comparable to that of a permutation test, with the advantage of a much-reduced computational cost. We introduce the p-value trace, a plot of the negative logarithm of the p-values of ridge regression coefficients with increasing shrinkage parameter, which enables the visualisation of the change in p-value of the regression coefficients with increasing penalisation. We apply the proposed method to a lung cancer case-control data set from EPIC, the European Prospective Investigation into Cancer and Nutrition. Conclusions The proposed test is a useful alternative to a permutation test for the estimation of the significance of ridge regression coefficients, at a much-reduced computational cost. The p-value trace is an informative graphical tool for evaluating the results of a test of significance of ridge regression coefficients as the shrinkage parameter increases, and the proposed test makes its production computationally feasible.

Expression and clinical significance of Pax6 gene in retinoblastoma

Directory of Open Access Journals (Sweden)

Hai-Dong Huang

2013-07-01

Full Text Available AIM: To discuss the expression and clinical significance of Pax6 gene in retinoblastoma(Rb. METHODS: Totally 15 cases of fresh Rb organizations were selected as observation group and 15 normal retinal organizations as control group. Western-Blot and reverse transcriptase polymerase chain reaction(RT-PCRmethods were used to detect Pax6 protein and Pax6 mRNA expressions of the normal retina organizations and Rb organizations. At the same time, Western Blot method was used to detect the Pax6 gene downstream MATH5 and BRN3b differentiation gene protein level expression. After the comparison between two groups, the expression and clinical significance of Pax6 gene in Rb were discussed. RESULTS: In the observation group, average value of mRNA expression of Pax6 gene was 0.99±0.03; average value of Pax6 gene protein expression was 2.07±0.15; average value of BRN3b protein expression was 0.195±0.016; average value of MATH5 protein expression was 0.190±0.031. They were significantly higher than the control group, and the differences were statistically significant(PCONCLUSION: Abnormal expression of Pax6 gene is likely to accelerate the occurrence of Rb.

Protein Crystallography: A 'Must' Technology for Drug Design

International Nuclear Information System (INIS)

Matsuzaki, Takao

2004-01-01

The history of drug-related protein crystallography and drug design is reviewed to show that 'Lead Generation' is high-lighted in the pharmaceutical industry nowadays. A new drug design method has been developed. The method gave very high success rate; 10-60 % gave < 100 μM, 90 % gave < 10 mM. The crystal structures of drug-protein complexes have become even more important to give solid experimental bases for e.g. 1,000 designed structures and to find the new mechanisms of drug action

Undergraduate prosthetics and orthotics teaching methods: A baseline for international comparison.

Science.gov (United States)

Aminian, Gholamreza; O'Toole, John M; Mehraban, Afsoon Hassani

2015-08-01

Education of Prosthetics and Orthotics is a relatively recent professional program. While there has been some work on various teaching methods and strategies in international medical education, limited publication exists within prosthetics and orthotics. To identify the teaching and learning methods that are used in Bachelor-level prosthetics and orthotics programs that are given highest priority by expert prosthetics and orthotics instructors from regions enjoying a range of economic development. Mixed method. The study partly documented by this article utilized a mixed method approach (qualitative and quantitative methods) within which each phase provided data for other phases. It began with analysis of prosthetics and orthotics curricula documents, which was followed by a broad survey of instructors in this field and then a modified Delphi process. The expert instructors who participated in this study gave high priority to student-centered, small group methods that encourage critical thinking and may lead to lifelong learning. Instructors from more developed nations placed higher priority on student's independent acquisition of prosthetics and orthotics knowledge, particularly in clinical training. Application of student-centered approaches to prosthetics and orthotics programs may be preferred by many experts, but there appeared to be regional differences in the priority given to different teaching methods. The results of this study identify the methods of teaching that are preferred by expert prosthetics and orthotics instructors from a variety of regions. This treatment of current instructional techniques may inform instructor choice of teaching methods that impact the quality of education and improve the professional skills of students. © The International Society for Prosthetics and Orthotics 2014.

Base Deficit as an Indicator of Significant Blunt Abdominal Trauma

African Journals Online (AJOL)

multiruka1

important cause of morbidity and mortality among trauma patients. ... the use of BD as an indicator of significant BAT. Methods: ... Key words: Base deficit, Blunt abdominal trauma,. Predictor. ..... Delineate Risk for Torso Injury in Stable Patients.

Reflections on the added value of using mixed methods in the SCAPE study.

Science.gov (United States)

Murphy, Kathy; Casey, Dympna; Devane, Declan; Meskell, Pauline; Higgins, Agnes; Elliot, Naomi; Lalor, Joan; Begley, Cecily

2014-03-01

To reflect on the added value that a mixed method design gave in a large national evaluation study of specialist and advanced practice (SCAPE), and to propose a reporting guide that could help make explicit the added value of mixed methods in other studies. Recently, researchers have focused on how to carry out mixed methods research (MMR) rigorously. The value-added claims for MMR include the capacity to exploit the strengths and compensate for weakness inherent in single designs, generate comprehensive description of phenomena, produce more convincing results for funders or policy-makers and build methodological expertise. Data illustrating value added claims were drawn from the SCAPE study. Studies about the purpose of mixed methods were identified from a search of literature. The authors explain why and how they undertook components of the study, and propose a guideline to facilitate such studies. If MMR is to become the third methodological paradigm, then articulation of what extra benefit MMR adds to a study is essential. The authors conclude that MMR has added value and found the guideline useful as a way of making value claims explicit. The clear articulation of the procedural aspects of mixed-methods research, and identification of a guideline to facilitate such research, will enable researchers to learn more effectively from each other.

Meta-analytic methods for pooling rates when follow-up duration varies: a case study

Directory of Open Access Journals (Sweden)

Wolf Fredric M

2004-07-01

Full Text Available Abstract Background Meta-analysis can be used to pool rate measures across studies, but challenges arise when follow-up duration varies. Our objective was to compare different statistical approaches for pooling count data of varying follow-up times in terms of estimates of effect, precision, and clinical interpretability. Methods We examined data from a published Cochrane Review of asthma self-management education in children. We selected two rate measures with the largest number of contributing studies: school absences and emergency room (ER visits. We estimated fixed- and random-effects standardized weighted mean differences (SMD, stratified incidence rate differences (IRD, and stratified incidence rate ratios (IRR. We also fit Poisson regression models, which allowed for further adjustment for clustering by study. Results For both outcomes, all methods gave qualitatively similar estimates of effect in favor of the intervention. For school absences, SMD showed modest results in favor of the intervention (SMD -0.14, 95% CI -0.23 to -0.04. IRD implied that the intervention reduced school absences by 1.8 days per year (IRD -0.15 days/child-month, 95% CI -0.19 to -0.11, while IRR suggested a 14% reduction in absences (IRR 0.86, 95% CI 0.83 to 0.90. For ER visits, SMD showed a modest benefit in favor of the intervention (SMD -0.27, 95% CI: -0.45 to -0.09. IRD implied that the intervention reduced ER visits by 1 visit every 2 years (IRD -0.04 visits/child-month, 95% CI: -0.05 to -0.03, while IRR suggested a 34% reduction in ER visits (IRR 0.66, 95% CI 0.59 to 0.74. In Poisson models, adjustment for clustering lowered the precision of the estimates relative to stratified IRR results. For ER visits but not school absences, failure to incorporate study indicators resulted in a different estimate of effect (unadjusted IRR 0.77, 95% CI 0.59 to 0.99. Conclusions Choice of method among the ones presented had little effect on inference but affected the

A New Image Encryption Technique Combining Hill Cipher Method, Morse Code and Least Significant Bit Algorithm

Science.gov (United States)

Nofriansyah, Dicky; Defit, Sarjon; Nurcahyo, Gunadi W.; Ganefri, G.; Ridwan, R.; Saleh Ahmar, Ansari; Rahim, Robbi

2018-01-01

Cybercrime is one of the most serious threats. Efforts are made to reduce the number of cybercrime is to find new techniques in securing data such as Cryptography, Steganography and Watermarking combination. Cryptography and Steganography is a growing data security science. A combination of Cryptography and Steganography is one effort to improve data integrity. New techniques are used by combining several algorithms, one of which is the incorporation of hill cipher method and Morse code. Morse code is one of the communication codes used in the Scouting field. This code consists of dots and lines. This is a new modern and classic concept to maintain data integrity. The result of the combination of these three methods is expected to generate new algorithms to improve the security of the data, especially images.

Multi-mycotoxin stable isotope dilution LC-MS/MS method for Fusarium toxins in beer.

Science.gov (United States)

Habler, Katharina; Gotthardt, Marina; Schüler, Jan; Rychlik, Michael

2017-03-01

A stable isotope dilution LC-MS/MS multi-mycotoxin method was developed for 12 different Fusarium toxins including modified mycotoxins in beer (deoxynivalenol-3-glucoside, deoxynivalenol, 3-acetyldeoxynivalenol, 15-acetyl-deoxynivalenol, HT2-toxin, T2-toxin, enniatin B, B1, A1, A, beauvericin and zearalenone). As sample preparation and purification of beer a combined solid phase extraction for trichothecenes, enniatins, beauvericin and zearalenone was firstly developed. The validation of the new method gave satisfying results: intra-day and inter-day precision and recoveries were 1-5%, 2-8% and 72-117%, respectively. In total, 61 different organic and conventional beer samples from Germany and all over the world were analyzed by using the newly developed multi-mycotoxin method. In summary, deoxynivalenol, deoxynivalenol-3-glucoside, 3-acetyldeoxynivaleneol and enniatin B were quantified in rather low contents in the investigated beer samples. None of the other monitored Fusarium toxins like 15-acetyldeoxynivalenol, HT2- and T2-toxin, zearalenone, enniatin B1, A1, A or beauvericin were detectable. Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparison of extrapolation methods for creep rupture stresses of 12Cr and 18Cr10NiTi steels

International Nuclear Information System (INIS)

Ivarsson, B.

1979-01-01

As a part of a Soviet-Swedish research programme the creep rupture properties of two heat resisting steels namely a 12% Cr steel and an 18% Cr12% Ni titanium stabilized steel have been studied. One heat from each country of both steels were creep tested. The strength of the 12% Cr steels was similar to earlier reported strength values, the Soviet steel being some-what stronger due to a higher tungsten content. The strength of the Swedish 18/12 Ti steel agreed with earlier results, while the properties of the Soviet steel were inferior to those reported from earlier Soviet creep testings. Three extrapolation methods were compared on creep rupture data collected in both countries. Isothermal extrapolation and an algebraic method of Soviet origin gave in many cases rather similar results, while the parameter method recommended by ISO resulted in higher rupture strength values at longer times. (author)

Identifying significant temporal variation in time course microarray data without replicates

Directory of Open Access Journals (Sweden)

Porter Weston

2009-03-01

Full Text Available Abstract Background An important component of time course microarray studies is the identification of genes that demonstrate significant time-dependent variation in their expression levels. Until recently, available methods for performing such significance tests required replicates of individual time points. This paper describes a replicate-free method that was developed as part of a study of the estrous cycle in the rat mammary gland in which no replicate data was collected. Results A temporal test statistic is proposed that is based on the degree to which data are smoothed when fit by a spline function. An algorithm is presented that uses this test statistic together with a false discovery rate method to identify genes whose expression profiles exhibit significant temporal variation. The algorithm is tested on simulated data, and is compared with another recently published replicate-free method. The simulated data consists both of genes with known temporal dependencies, and genes from a null distribution. The proposed algorithm identifies a larger percentage of the time-dependent genes for a given false discovery rate. Use of the algorithm in a study of the estrous cycle in the rat mammary gland resulted in the identification of genes exhibiting distinct circadian variation. These results were confirmed in follow-up laboratory experiments. Conclusion The proposed algorithm provides a new approach for identifying expression profiles with significant temporal variation without relying on replicates. When compared with a recently published algorithm on simulated data, the proposed algorithm appears to identify a larger percentage of time-dependent genes for a given false discovery rate. The development of the algorithm was instrumental in revealing the presence of circadian variation in the virgin rat mammary gland during the estrous cycle.

Evaluation of three methods for hemoglobin measurement in a blood donor setting

Directory of Open Access Journals (Sweden)

Jacob Rosenblit

1999-05-01

Full Text Available CONTEXT: The hemoglobin (Hb level is the most-used parameter for screening blood donors for the presence of anemia, one of the most-used methods for measuring Hb levels is based on photometric detection of cyanmetahemoglobin, as an alternative to this technology, HemoCue has developed a photometric method based on the determination of azide metahemoglobin. OBJECTIVE: To evaluate the performance of three methods for hemoglobin (Hb determination in a blood bank setting. DESIGN: Prospective study utilizing blood samples to compare methods for Hb determination. SETTING: Hemotherapy Service of the Hospital Israelita Albert Einstein, a private institution in the tertiary health care system. SAMPLE: Serial blood samples were collected from 259 individuals during the period from March to June 1996. MAIN MEASUREMENTS: Test performances and their comparisons were assessed by the analysis of coefficients of variation (CV, linear regression and mean differences. RESULTS: The CV for the three methods were: Coulter 0.68%, Cobas 0.82% and HemoCue 0.69%. There was no difference between the mean Hb determination for the three methods (p>0.05. The Coulter and Cobas methods showed the best agreement and the HemoCue method gave a lower Hb determination when compared to both the Coulter and Cobas methods. However, pairs of methods involving the HemoCue seem to have narrower limits of agreement (± 0.78 and ± 1.02 than the Coulter and Cobas combination (± 1.13. CONCLUSION: The three methods provide good agreement for hemoglobin determination.

Real significance of skin contamination is

International Nuclear Information System (INIS)

Sudmann, R.H.

1983-01-01

For five decades, health physicists have discussed the thickness, area, significance of radioactive contamination and the exposures to various portions of the skin. Concern about instances of skin contamination extend beyond the resultant organ dose simply because it is a recognizable and quantifiable event. As such, there is a tendency for management and regulatory agencies to use it as a trend indicator. The final result is a score card similar to the list of OSHA reportable accidents. In fact, the skin contamination incidence rate has a somewhat different meaning to the health physicist, to the manager, and to the regulator. The question must then be asked, What is the true significance of skin contamination, Is it the resultant skin dose, Is it an indicator of loss of control, Is it both or neither. In order to answer these questions, Rockwell Hanford Operations began analysis of the previous five years records of skin contamination cases. Since by policy each incidence of skin contamination is documented, a large percentage of the 425 records analyzed were of low level activity (less than 100 dpm/cm 2 ) on the extremeties, primarily hands and fingers. Most of these cases were readily decontaminated with soap and water. Individual elements studied included: detection/monitoring methods and limits; impact of type of operation on the incidence rate; causes of and methods for reduction of the incidence rate; reporting and documentation; and dose assessment. Results of the study indicate that skin contamination rarely presents a beta dose problem because it is normally highly localized on the extremeties. Only in unusual cases does it represent a potential for internal deposition. Thus, the real importance of skin contamination incidence is as an indicator of deteriorating conditions and should be reviewed by health physicists, managers and regulators as such

Significant exposures to isoeugenol derivaties in perfumes

DEFF Research Database (Denmark)

Rastogi, Suresh Chandra; Johansen, Jeanne Duus

2008-01-01

in perfumes/aftershaves. MATERIALS AND METHODS: 29 international brand perfumes/aftershaves were analysed for the target fragrance ingredient by gas chromatography-mass spectrometry. All samples were analysed in duplicate at detection levels of 1-5 p.p.m. RESULTS: 16 products (55%) contained isoeugenol...... was not detected in any of the investigated products. CONCLUSIONS: Isoeugenyl acetate is present in perfumes/aftershaves, in some products in significant amounts. This may lead to elicitation of contact allergy in isoeugenol-sensitized individuals and may contribute to unchanged levels of isoeugenol sensitization....

Study on the placement of phosphorus fertilizer to improve fertilizer utilization by lowland rice

International Nuclear Information System (INIS)

Sisworo, W.H.; Riswantoro; Mardjo, M.

1976-01-01

An experiment for studying the placement of phosphorus fertilizer was carried out in the glass house by using 32 P-labelled superphosphate. The specific activity of the labelled fertilizer used was 0,25 mCi/g P 2 O 5 . Three placement methods were studied: (1) Hill placement: Fertilizer was burried at a distance of 5cm from the plants at the depth of 5 cm, (2) Surface placement: Fertilizer was spread on the surface, and (3) Soil mixed application: Fertilizer was mixed with the soil at the depth of 5 cm. Superphosphate was applied at the rates of 0, 30, 60, 90, and 120 kg P 25 /ha. Results obtained from the experiment showed that the dry matter production was significantly affected by the methods of placement of phosphorus fertilizer. Soil mixed placement gave the lowest yield of dry plant material. It differed significantly from the two other methods of placement. However, there was no significant difference between hill and surface placement. The placement of phosphorus fertilizer significantly affected the total uptake of phosphorus nutrient, uptake fertilizer phosphorus, and the percentage of fertilizer utilization. Surface placement gave the highest utilization of fertilizer when supplied at rates higher than 60 kg P 2 O 5 /ha. At low rate applications, hill placement was the best, but, at rates higher than 60 kg P 2 O 5 /ha the percentage of fertilizer utilization decreased. Soil mixed application was the least efficient fertilizer utilization. (author)

Carbon-tuned bonding method significantly enhanced the hydrogen storage of BN-Li complexes.

Science.gov (United States)

Deng, Qing-ming; Zhao, Lina; Luo, You-hua; Zhang, Meng; Zhao, Li-xia; Zhao, Yuliang

2011-11-01

Through first-principles calculations, we found doping carbon atoms onto BN monolayers (BNC) could significantly strengthen the Li bond on this material. Unlike the weak bond strength between Li atoms and the pristine BN layer, it is observed that Li atoms are strongly hybridized and donate their electrons to the doped substrate, which is responsible for the enhanced binding energy. Li adsorbed on the BNC layer can serve as a high-capacity hydrogen storage medium, without forming clusters, which can be recycled at room temperature. Eight polarized H(2) molecules are attached to two Li atoms with an optimal binding energy of 0.16-0.28 eV/H(2), which results from the electrostatic interaction of the polarized charge of hydrogen molecules with the electric field induced by positive Li atoms. This practical carbon-tuned BN-Li complex can work as a very high-capacity hydrogen storage medium with a gravimetric density of hydrogen of 12.2 wt%, which is much higher than the gravimetric goal of 5.5 wt % hydrogen set by the U.S. Department of Energy for 2015.

THE METHOD OF CONSTRUCTING MODELS OF STRESS-TESTING OF THE TRADING PORTFOLIO OF FINANCIAL ORGANIZATIONS

Directory of Open Access Journals (Sweden)

Alimbaev Farkhad

2009-11-01

Full Text Available The financial crisis gave an impetus to finding “weaknesses” in financial institutions. One such tool is the stress-testing. This method is intended to identify through modeling “hypothetical” or “historical” scenarios, the most losses, in the execution of a script. In the simulation of hypothetical scenarios to find the impact factor, as shock events on the trade portfolio. When using historical scenarios, as the shocks applied developments in the past that have caused catastrophic losses, both in quantitative and qualitative size. For example, such scenarios can be: financial crises of the 90-ies and the current decline in international stock markets, a drop or increase in foreign exchange rates, etc.

Comparison between amperometric and true potentiometric end-point detection in the determination of water by the Karl Fischer method.

Science.gov (United States)

Cedergren, A

1974-06-01

A rapid and sensitive method using true potentiometric end-point detection has been developed and compared with the conventional amperometric method for Karl Fischer determination of water. The effect of the sulphur dioxide concentration on the shape of the titration curve is shown. By using kinetic data it was possible to calculate the course of titrations and make comparisons with those found experimentally. The results prove that the main reaction is the slow step, both in the amperometric and the potentiometric method. Results obtained in the standardization of the Karl Fischer reagent showed that the potentiometric method, including titration to a preselected potential, gave a standard deviation of 0.001(1) mg of water per ml, the amperometric method using extrapolation 0.002(4) mg of water per ml and the amperometric titration to a pre-selected diffusion current 0.004(7) mg of water per ml. Theories and results dealing with dilution effects are presented. The time of analysis was 1-1.5 min for the potentiometric and 4-5 min for the amperometric method using extrapolation.

Comparison of Cardiovascular Risk Screening Methods and Mortality Data among Hungarian Primary Care Population: Preliminary Results of the First Government-Financed Managed Care Program.

Science.gov (United States)

Móczár, Csaba; Rurik, Imre

2015-09-01

Besides participation in the primary prevention, screening as secondary prevention is an important requirement for primary care services. The effect of this work is influenced by the characteristics of individual primary care practices and doctors' screening habits, as well as by the regulation of screening processes and available financial resources. Between 1999 and 2009, a managed care program was introduced and carried out in Hungary, financed by the government. This financial support and motivation gave the opportunity to increase the number of screenings. 4,462 patients of 40 primary care practices were screened on the basis of SCORE risk assessment. The results of the screening were compared on the basis of two groups of patients, namely: those who had been pre-screened (pre-screening method) for known risk factors in their medical history (smoking, BMI, age, family cardiovascular history), and those randomly screened. The authors also compared the mortality data of participating primary care practices with the regional and national data. The average score was significantly higher in the pre-screened group of patients, regardless of whether the risk factors were considered one by one or in combination. Mortality was significantly lower in the participating primary practices than had been expected on the basis of the national mortality data. This government-financed program was a big step forward to establish a proper screening method within Hungarian primary care. Performing cardiovascular screening of a selected target group is presumably more appropriate than screening within a randomly selected population. Both methods resulted in a visible improvement in regional mortality data, though it is very likely that with pre-screening a more cost-effective selection for screening may be obtained.

Furnace Brazing Parameters Optimized by Taguchi Method and Corrosion Behavior of Tube-Fin System of Automotive Condensers

Science.gov (United States)

Guía-Tello, J. C.; Pech-Canul, M. A.; Trujillo-Vázquez, E.; Pech-Canul, M. I.

2017-08-01

Controlled atmosphere brazing has a widespread industrial use in the production of aluminum automotive heat exchangers. Good-quality joints between the components depend on the initial condition of materials as well as on the brazing process parameters. In this work, the Taguchi method was used to optimize the brazing parameters with respect to corrosion performance for tube-fin mini-assemblies of an automotive condenser. The experimental design consisted of five factors (micro-channel tube type, flux type, peak temperature, heating rate and dwell time), with two levels each. The corrosion behavior in acidified seawater solution pH 2.8 was evaluated through potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) measurements. Scanning electron microscope (SEM) and energy-dispersive x-ray spectroscopy (EDS) were used to analyze the microstructural features in the joint zone. The results showed that the parameters that most significantly affect the corrosion rate are the type of flux and the peak temperature. The optimal conditions were: micro-channel tube with 4.2 g/m2 of zinc coating, standard flux, 610 °C peak temperature, 5 °C/min heating rate and 4 min dwell time. The corrosion current density value of the confirmation experiment is in excellent agreement with the predicted value. The electrochemical characterization for selected samples gave indication that the brazing conditions had a more significant effect on the kinetics of the hydrogen evolution reaction than on the kinetics of the metal dissolution reaction.

In situ measurements of tritium evapotranspiration (³H-ET) flux over grass and soil using the gradient and eddy covariance experimental methods and the FAO-56 model.

Science.gov (United States)

Connan, O; Maro, D; Hébert, D; Solier, L; Caldeira Ideas, P; Laguionie, P; St-Amant, N

2015-10-01

The behaviour of tritium in the environment is linked to the water cycle. We compare three methods of calculating the tritium evapotranspiration flux from grassland cover. The gradient and eddy covariance methods, together with a method based on the theoretical Penmann-Monteith model were tested in a study carried out in 2013 in an environment characterised by high levels of tritium activity. The results show that each of the three methods gave similar results. The various constraints applying to each method are discussed. The results show a tritium evapotranspiration flux of around 15 mBq m(-2) s(-1) in this environment. These results will be used to improve the entry parameters for the general models of tritium transfers in the environment. Copyright © 2015 Elsevier Ltd. All rights reserved.

Benchmarking semiempirical and DFT methods for the interaction of thiophene and diethyl sulfide molecules with a Ti(OH)4(H2O) cluster.

Science.gov (United States)

Vorontsov, Alexander V; Smirniotis, Panagiotis G

2017-08-01

Semiempirical methods pm6 and pm7 as well as density functional theory functionals exchange LSDA, exchange-correlation PW91 and PBE, hybrid B3LYP1 and PBE0 were compared for energy and geometry of thiophene, diethyl sulfide (DES) molecules and their binding to a frozen Ti(OH) 4 (H 2 O) complex having one coordinatively unsaturated Ti 5C site representing small fragment of TiO 2 anatase (001) surface. PBE0/6-31G(d) with DFT-D3 dispersion correction was the best method for description of thiophene and DES molecules geometries as comparison with experimental data demonstrated. Semiempirical methods pm6 and pm7 resulted in only three of four possible binding configurations of thiophene with the Ti(OH) 4 (H 2 O) complex while pm7 described correctly the enthalpy and all configurations of DES binding with the Ti(OH) 4 (H 2 O) complex. SBKJC pseudopotential and LSDA with and without dispersion correction produced flawed results for many configurations. PBE0 and PBE with and without dispersion correction and PW91 with 6-31G(d) basis set systematically produced dependable results for thiophene and DES binding to the Ti(OH) 4 (H 2 O) complex. PBE0-D3/6-31G(d), B3LYP1-D3/6-31G(d), and PBE-D3/6-31G(d) gave best match of binding energy for thiophene while PBE0/6-31G(d) gave best match of DES binding energy as comparison with CCSD(T) energy demonstrated. On the basis of the superior results obtained with PBE0/6-31G(d), it is the recommended method for modeling of adsorption over TiO 2 surfaces. Such a conclusion is in agreement with recent literature.

Effectiveness of methods for reducing acrylamide in bakery products.

Science.gov (United States)

Sadd, Peter A; Hamlet, Colin G; Liang, Li

2008-08-13

Pilot-scale bread, biscuit, and cracker doughs have been baked to assess how well recipe changes could reduce acrylamide in commercial bakery products. Removing ammonium-based raising agents was beneficial in biscuits. In doughs, long yeast fermentations were an effective way of reducing asparagine levels and hence acrylamide. At moderate fermentation times fructose levels increased, but the yeast later absorbed this, so the net effect on acrylamide was beneficial. Metal ions such as calcium reduced acrylamide when added as the carbonate or chloride. Hence, the fortification of flour with calcium carbonate, over and above its natural mineral content, has an additional benefit. However, some other possible methods of adding calcium to bakery doughs, for example, via the permitted preservative calcium propionate, were not beneficial. Amino acid addition to doughs gave modest reductions in acrylamide. Lowering the dough pH reduced acrylamide, but at the expense of higher levels of other process contaminants such as 3-monochloropropane-1,2-diol (3-MCPD).

Parallel efficient rate control methods for JPEG 2000

Science.gov (United States)

Martínez-del-Amor, Miguel Á.; Bruns, Volker; Sparenberg, Heiko

2017-09-01

Since the introduction of JPEG 2000, several rate control methods have been proposed. Among them, post-compression rate-distortion optimization (PCRD-Opt) is the most widely used, and the one recommended by the standard. The approach followed by this method is to first compress the entire image split in code blocks, and subsequently, optimally truncate the set of generated bit streams according to the maximum target bit rate constraint. The literature proposes various strategies on how to estimate ahead of time where a block will get truncated in order to stop the execution prematurely and save time. However, none of them have been defined bearing in mind a parallel implementation. Today, multi-core and many-core architectures are becoming popular for JPEG 2000 codecs implementations. Therefore, in this paper, we analyze how some techniques for efficient rate control can be deployed in GPUs. In order to do that, the design of our GPU-based codec is extended, allowing stopping the process at a given point. This extension also harnesses a higher level of parallelism on the GPU, leading to up to 40% of speedup with 4K test material on a Titan X. In a second step, three selected rate control methods are adapted and implemented in our parallel encoder. A comparison is then carried out, and used to select the best candidate to be deployed in a GPU encoder, which gave an extra 40% of speedup in those situations where it was really employed.

Comparison of the methods for tissue triiodothyronine T(3) extraction and subsequent radioimmunoassay

International Nuclear Information System (INIS)

Takaishi, M.; Miyachi, Y.; Aoki, M.; Shishiba, Y.; Asahi Life Foundation, Tokyo

1978-01-01

Although there have been various reports on tissue T 3 concentration, the examination of the quality of radioimmunoassay has not been available. In the present study, we tried to determine whether the available methods for T 3 extraction are adequate for the various methods of T 3 radioimmunoassays used. T 3 was extracted from liver by ethanol extraction or by acid butanol extraction (Flock's method) and the extract was applied to radioimmunoassay either by Seralute T 3 column, ANS-double antibody or the ANS-charcoal method. The values of T 3 were compared with those obtained by isotope-equilibration method. The dilution curve of ethanol extract was not parallel with that of the standard in ANS-charcoal or ANS-double antibody technique. When the extract was tested by Seralate method, the dilution curve was parallel to the standard, whereas the T 3 value obtained with this method was two-fold higher than that with the isotope equilibration technique. The analysis of the ethanol extract suggested that the lipid extracted by ethanol interfered with the assay. The acid butanol extract when tested either by the ANS-double antibody or Seralate method, showed parallelism to the standard curve and gave T 3 values almost identical with those by the isotope-equilibration method. When tested by ANS-charcoal method, the dilution curve of the acid butanol extract was not parallel to the standard. Thus, to obtain reliable results, tissue extraction by Flock's method and subsequent T 3 radioimmunoassay by either ANS-double antibody or Seralate T 3 method are recommended. (author)

SPE HG-AAS method for the determination of inorganic arsenic in rice—results from method validation studies and a survey on rice products

DEFF Research Database (Denmark)

Rasmussen, Rie Romme; Qian, Yiting; Sloth, Jens Jørgen

2013-01-01

spectrometry (HG-AAS) detection. This approach was earlier developed for seafood samples (Rasmussen et al., Anal Bioanal Chem 403:2825–2834, 2012) and has in the present work been tailored for rice products and further optimised for a higher sample throughput and a lower detection limit. Water bath heating (90...... °C, 60 min) of samples with dilute HNO3 and H2O2 solubilised and oxidised all iAs to arsenate (AsV). Loading of buffered sample extracts (pH 6 ± 1) followed by selective elution of arsenate from a strong anion exchange SPE cartridge enabled the selective iAs quantification by HG-AAS, measuring total...... arsenic (As) in the SPE eluate. The in-house validation gave mean recoveries of 101–106 % for spiked rice samples and in two reference samples. The limit of detection was 0.02 mg kg−1, and repeatability and intra-laboratory reproducibility were less than 6 and 9 %, respectively. The SPE HG-AAS method...

A novel liquid chromatography method using diode-array detector for the determination of oleuropein in dietary supplements.

Science.gov (United States)

Bertolini, Tiziana; Vicentini, Lorenza; Boschetti, Silvia; Andreatta, Paolo; Gatti, Rita

2016-09-10

A simple and fast chromatographic method using ultraviolet diode-array detector (UV-DAD) was developed for the automatic high performance liquid chromatography (HPLC) determination of the title of oleuropein in a new dietary supplements in form of effervescent granules. The chromatographic separations were performed on a C18 core-shell column with detection at λ=232nm. The mobile phase consisted of deionized water with 0.1% TFA and acetonitrile under gradient conditions at a flow-rate of 0.8mL/min. Oleuropein and oleuroside present in the raw material were characterized by high performance liquid chromatography-electrospray ionization tandem mass spectrometry (HPLC-ESI-MS/MS). The validation of the analytical procedure has been performed determining the following parameters: specificity, linearity, repeatability, reproducibility, accuracy, limit of quantification (LOQ), stability of the standard and sample solutions. Linear response was observed in fortified placebo solutions (determination coefficient: 0.9998). Intra-day precision (relative standard deviation, RSD) was ≤5.0% for peak area and for retention times (tR) without significant differences between intra- and inter-day data. The limits of quantitation (LOQ) was about 5μg/mL and 9pmol/inject. Oleuropein recovery studies gave good results (99.9%) with a R.S.D. of 0.5%. The speed of analysis and the stability of the solutions with a fluctuation Δ (%) ≤2.0 at room temperature means an undoubted advantage of the method allowing the simultaneous preparation of many samples and consecutive chromatographic analyses by using an autosampler. The developed method is suitable for the quality control of oleuropein in raw material and industrial products. The method can be applied in any analytical laboratory not requiring a sophisticated instrumentation. Copyright © 2016 Elsevier B.V. All rights reserved.

Fundamental and clinical studies on simultaneous, quantitative analysis of hepatobiliary and gastrointestinal scintigrams using double isotope method

Energy Technology Data Exchange (ETDEWEB)

Aoki, Y; Kakihara, M; Sasaki, M; Tabuse, Y; Takei, N [Wakayama Medical Coll. (Japan)

1981-04-01

Double isotope method was applied to carry out simultaneous and quantitative analysis of hepatobiliary and gastrointestinal scintigrams. A scinticamera with parallel collimator for medium energy was connected to a computer to distinguish the two isotopes at a time. 4mCi of sup(99m)Tc-(Sn)-pyridoxylideneisoleucine (Tc-PI) and 200 ..mu..Ci of /sup 111/In-diethylenetriaminepentaacetic acid (In-DTPA) were administrated by i.v. injection and per oral, respectively. Three normal (two women and a man) and 16 patients after the operation of gastric cancer (10 recovered by Roux-en Y method after the total gastrectomy, and 6 recovered after the operation replacing the jejunum between the esophagus and duodenum) were investigated. The process of bile secretion and its mixing with food were followed by the scanning quantitatively. The analysis of time-activity variation at each organ indicated that the replacing operation gave more physiological recovery than that by Roux-en Y method. This method is noninvasive to patients and is promising to follow the process or activity of digestion in any digestive organ after surgery.

The Effects of Using Seaweed (E. Cottonii on Physical Quality and Organoleptic of Chicken Nuggets

Directory of Open Access Journals (Sweden)

Djalal Rosyidi

2012-02-01

Full Text Available This research was experimental method with Completely Random Design.  Seaweed used to chicken nuggets in the vary concentration, namely: 0% (F0, 10% (F1, 20% (F2, 30% (F3, 40% (F4. The observed variables were texture, water holding capacity (WHC, pH, and organoleptic quality of chicken nuggets. Collected data were analyzed using analisys variation method and followed by Duncan analysis if the result on the previous analysis showed significant difference. The  result  showed  that  chicken  nuggets  using  seaweed  gave highly significant effect  (P<0.01 on  texture, WHC, pH, and   organoleptic quality. The best result was chicken nuggets made with used of seaweed  10%;  7.97 N of texture; 4.50% of WHC; 6.16 of pH; 6.98 of texture organoleptic score; and 6.26 of taste organoleptic score. The conclusion of this research was the using of seaweed to chicken nuggets gave a significant effect on  texture, WHC, pH, and organoleptic quality. Based on the result, it suggested that using 10% of seaweed to make chicken nugeets.   Keyword : water holding capacity, chicken nuggets, seaweed

Determination of fossil carbon content in Swedish waste fuel by four different methods.

Science.gov (United States)

Jones, Frida C; Blomqvist, Evalena W; Bisaillon, Mattias; Lindberg, Daniel K; Hupa, Mikko

2013-10-01

This study aimed to determine the content of fossil carbon in waste combusted in Sweden by using four different methods at seven geographically spread combustion plants. In total, the measurement campaign included 42 solid samples, 21 flue gas samples, 3 sorting analyses and 2 investigations using the balance method. The fossil carbon content in the solid samples and in the flue gas samples was determined using (14)C-analysis. From the analyses it was concluded that about a third of the carbon in mixed Swedish waste (municipal solid waste and industrial waste collected at Swedish industry sites) is fossil. The two other methods (the balance method and calculations from sorting analyses), based on assumptions and calculations, gave similar results in the plants in which they were used. Furthermore, the results indicate that the difference between samples containing as much as 80% industrial waste and samples consisting of solely municipal solid waste was not as large as expected. Besides investigating the fossil content of the waste, the project was also established to investigate the usability of various methods. However, it is difficult to directly compare the different methods used in this project because besides the estimation of emitted fossil carbon the methods provide other information, which is valuable to the plant owner. Therefore, the choice of method can also be controlled by factors other than direct determination of the fossil fuel emissions when considering implementation in the combustion plants.

Development of a quantitative evaluation method for non-technical skills preparedness of operation teams in nuclear power plants to deal with emergency conditions

International Nuclear Information System (INIS)

Yim, Ho Bin; Kim, Ar Ryum; Seong, Poong Hyun

2013-01-01

in teams were changed, values of the NoT-SkiP were significantly changed. Nine teams participated in Interfacing System LOCA (ISLOCA) training; six teams failed to complete the given task, and three teams succeeded. The comparison of NoT-SkiP values of ISLOCA case with Operator Performance Assessment System (OPAS), which mainly check operators’ knowledge and the technical skills, developed by OECD Halden Reactor Project (HRP) gave a plausible reason why teams failed as well as intuitive results on ‘what to be considered in the non-technical skills aspects of teams’ for the next training. The proposed method requires more experiments in order for it to be established on a firm foundation; however, it certainly gives one possible way to supplement existing training strategy in the nuclear industry

Development of a quantitative evaluation method for non-technical skills preparedness of operation teams in nuclear power plants to deal with emergency conditions

Energy Technology Data Exchange (ETDEWEB)

Yim, Ho Bin; Kim, Ar Ryum [Department of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology, 373-1, Guseong-dong, Yuseong-gu, Daejeon 305-701 (Korea, Republic of); Seong, Poong Hyun, E-mail: phseong@kaist.ac.kr [Department of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology, 373-1, Guseong-dong, Yuseong-gu, Daejeon 305-701 (Korea, Republic of)

2013-02-15

in teams were changed, values of the NoT-SkiP were significantly changed. Nine teams participated in Interfacing System LOCA (ISLOCA) training; six teams failed to complete the given task, and three teams succeeded. The comparison of NoT-SkiP values of ISLOCA case with Operator Performance Assessment System (OPAS), which mainly check operators’ knowledge and the technical skills, developed by OECD Halden Reactor Project (HRP) gave a plausible reason why teams failed as well as intuitive results on ‘what to be considered in the non-technical skills aspects of teams’ for the next training. The proposed method requires more experiments in order for it to be established on a firm foundation; however, it certainly gives one possible way to supplement existing training strategy in the nuclear industry.

Testing the ISP method with the PARIO device: Accuracy of results and influence of homogenization technique

Science.gov (United States)

Durner, Wolfgang; Huber, Magdalena; Yangxu, Li; Steins, Andi; Pertassek, Thomas; Göttlein, Axel; Iden, Sascha C.; von Unold, Georg

2017-04-01

be measured explicitly and are used as fixed parameters in the PARIO evaluation, the error of the clay fraction is determined by error propagation from the sand and silt fraction. Homogenization of the suspension by overhead shaking gave lower reproducibility and smaller silt fractions than vertical stirring. However, it turned out that vertical stirring must be performed with sufficient rigour to obtain a fully homogeneous initial distribution. Analysis of material sieved to < 2000 μm and to < 200 μm gave equal results, i.e., there was no hint towards dragging effects of large particles. Complete removal of the sand fraction, i.e. sieving to < 63 μm lead to less silt, probably due to a loss of fine material by the sieving process. The PSD's obtained with the PARIO corresponded very well with the results of the Pipette method.

A Raman Study of Titanate Nanotubes

African Journals Online (AJOL)

NJD

HRTEM data are also consistent with the synthesis of ... The nano titania produced by the electrochemical and template methods, gave amorphous titania while titania nanotubes produced by 'soft' chemical processes gave materials with good.

Characterization of gold kiwifruit pectin from fruit of different maturities and extraction methods.

Science.gov (United States)

Yuliarti, Oni; Matia-Merino, Lara; Goh, Kelvin K T; Mawson, John; Williams, Martin A K; Brennan, Charles

2015-01-01

Studies on gold kiwifruit pectins are limited. In this work, the characterization of pectin isolated from two different stages of maturity of gold kiwifruit, namely early harvested fruit (EHF) and main harvested fruit (MHF) isolated by three methods (acid, water, enzymatic) was carried out. Pectins isolated from MHF were higher in galacturonic acid content (52-59% w/w) and weight-average molecular weights (Mw, 1.7-3.8 × 10(6)g/mol) compared with EHF pectins (29-49% w/w and 0.2-1.7 × 10(6)g/mol respectively). Enzymatic treatment gave the highest yield but lowest in Mw, viscosity and mechanical spectra for both maturities. The pectin of both maturities was classified as high-methoxyl pectin with the degree of esterification ranged from 82% to 90%. Water-extracted MHF pectin molecules had the highest RMS radius (182.7 nm) and Mw (3.75 × 10(6)g/mol). The water extraction method appeared to retain the native state of pectin molecules compared with acid and enzymatic extraction methods based on the Mw and viscosity data. Copyright © 2014 Elsevier Ltd. All rights reserved.

Prognosis of non-significant coronary atherosclerotic disease detected by coronary artery tomography

Energy Technology Data Exchange (ETDEWEB)

Barros, Marcio Vinicius Lins; Siqueira, Bruna Pinto; Guimaraes, Carolina Camargos Braichi; Cruz, David Filipe Silva; Guimaraes, Leiziane Assuncao Alves; Lima, Maicom Marcio Perigolo, E-mail: marciovlbarros@gmail.com [Faculdade de Saude e Ecologia Humana, Vespasiano, MG (Brazil); Nunes, Maria do Carmo Pereira [Universidade de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Faculdade de Medicina; Siqueira, Maria Helena Albernaz [Hospital Materdei, Belo Horizonte, MG (Brazil)

2015-07-15

Introduction: Although studies have shown high diagnostic accuracy of coronary tomography (CT) in detecting coronary artery disease (CAD), data on the prognostic value of this method in patients with no significant coronary obstruction are limited. Objective: To evaluate the value of CT in predicting adverse events in patients with suspected CAD and no significant coronary obstruction. Methods: We prospectively evaluated 440 patients between January 2008 and July 2013 by MDCT, diagnosed with no significant obstruction or no atherosclerotic coronary obstruction with an average follow-up of 33 months. The outcomes evaluated were: cardiac death, myocardial infarction, unstable angina associated with hospitalization or coronary artery bypass grafting. Results: Of the 440 patients studied, 295 (67%) were men with mean age 55.9 ± 12.0 years. Non-significant obstruction was found in 152 (35%) of the patients and there were 49 (11%) outcomes. In the multivariate analysis using the Cox regression model, the predictors of clinical outcomes were non-significant obstruction on CT (hazard ratio 3.51; 95% CI 1.73 - 7.8; p <0.01), age and hypertension. Non-significant obstruction on CT was associated with adverse clinical outcomes and survival analysis showed a significant difference (log-rank 24.6; p <0.01) in predicting these outcomes. Conclusion: The detection of non-significant atherosclerotic obstruction by CT was associated with the presence of adverse events in patients with suspected CAD, which may prove useful in the risk stratification of these patients. (author)

The Story and Significance of Prince Chanhua Offering Tribute to and Requesting a New Title from the Qing Court in the Early Qing Period

Institute of Scientific and Technical Information of China (English)

DengRuiling; ChenGuansheng

2003-01-01

On the basis of Chinese and Tibetan historical materials, Mr. Z. Ahmad in his Sino-Tibetan Relations in the 17th Century, published in 1970, gave a description of Prince Chanhua(lit. Prince of the Propagation of the Doctrine of the Buddha)repeatedly requesting a new title from the Qing court during the reign of Emperor Shunzhi.

A gamma camera method for quantitation of split renal function in children followed for vesicoureteric reflux

International Nuclear Information System (INIS)

Tamminen, T.E.; Riihimaeki, E.J.; Taehti, E.E.; Helsinki Univ. Central Hospital

1978-01-01

A method for quantitative estimation of split renal function using a computerized gamma camera system is described. 42 children and adolescents with existing or preexisting vesicouretric reflux and recurrent urinary tract infection were investigated. Total renal clearance of DTPA was calculated with a disapperarance curve derived from the largest extrarenal area in the field of view of a gamma camera with diverging collimator. Split renal function was estimated with the slopes of second phase renograms. The plasma disaapearance clearance of DTPA, calculated using one compartement model with two late blood samples, gave similar resusults with the clearance estimated from the body disappearance curves. The proportional planimetric renal parenchymal areas had good correlation with the split clearance estimated from renogram slopes. The method offers data on renal function and urinary tract dynamics which is very valuable in the follow-up of children with recurrent urinary tract infection and vesicoureteric reflux. (orig.) [de

Validation of the salivary urea and creatinine tests as screening methods of chronic kidney disease in Vietnamese patients.

Science.gov (United States)

Pham, Thuy Anh Vu

2017-11-01

The aims of this case control study were to correlate the serum and salivary urea as well as creatinine levels; and to evaluate salivary urea and creatinine as noninvasive alternatives to serum for creatinine estimation in chronic kidney disease (CKD) patients. Blood and saliva samples were collected from 112 CKD patients and 108 subjects without CKD for quantitative analysis of urea and creatinine. Spearman's correlation coefficients between salivary and serum urea as well as creatinine were obtained. Receiver operating characteristic analysis was done to assess the diagnostic tests of salivary urea and creatinine. Cut-off values were determined based on the best trade-off between the sensitivity and specificity for both salivary urea and creatinine. Salivary urea and creatinine concentrations were significantly higher in CKD patients than those in control subjects; and increased by the stages of the severity of the disease. The positive correlation was significantly found between salivary and serum creatinine (r  =  0.90) and between salivary and serum urea (r  =  0.73). Area under the curve for salivary urea was 0.76 and a cut-off value of 14.25 mmol/L gave a sensitivity of 82.9% and specificity of 57.8%. Area under the curve for salivary creatinine was 0.92 and a cut-off value of 0.24 mg/dL gave a sensitivity of 86.5% and specificity of 87.2%. Both salivary urea and creatinine have a high capacity for serum creatinine estimation. Salivary urea and creatinine tests can be used as low-cost, easily accessible and noninvasive tools for screening, diagnosing, monitoring treatment outcomes and ascertaining prognosis of chronic kidney disease.

Nitrogen Use Efficiency and Tomato Crop Response to Nitrogen Fertigation Using N15

International Nuclear Information System (INIS)

El-Zoreiky, S.; Quasmy, W.; El-Rosan, M.

2003-01-01

Field studies were conducted during two seasons at the Deir Alla Research Center to compare the conventional fertilization method with Fertigation on water and nitrogen use efficiency with a tomato crop (c v. Gardenia). Four N application rates (0,50,100 and 150 m NIL) were applied with the irrigation water and one soil application Ns) treatment, equivalent to one of the fertigation treatment, was included Labeled ammonium sulfate was applied to micro plots within the, micro plots to evaluate the N recovery and utilization efficiency Results obtained form tow seasons indicate that increasing the N rate significantly increased the total and marketable yield by both method of application suggesting that the crop was under fertilized. The so application treatment gave a higher yield than the control (N0) and lower one than the fertigated treatments. In comparison to the N0, the total number of fruits in both seasons was significantly increased at all N level. The soil application (Ns) treatment gave the lowest number fruits compared to the Fertigation treatments in the first season and higher number than the fertigated treatments in the second season

Multivariate Methods for Prediction of Geologic Sample Composition with Laser-Induced Breakdown Spectroscopy

Science.gov (United States)

Morris, Richard; Anderson, R.; Clegg, S. M.; Bell, J. F., III

2010-01-01

the CC ANN often gave results comparable to PLS. Averaging the spectra for each training sample and/or using feature selection to choose a small subset of wavelengths to use for predictions gave mixed results, with degraded performance in some cases and similar or slightly improved performance in other cases. However, training time was significantly reduced for both PLS and ANN methods by implementing feature selection, making this a potentially appealing method for initial, rapid-turn-around analyses necessary for Chemcam's tactical role on MSL. Choice of training samples has a strong influence on the accuracy of predictions. We are currently investigating the use of clustering algorithms (e.g. k-means, neural gas, etc.) to identify training sets that are spectrally similar to the unknown samples that are being predicted, and therefore result in improved predictions

The Kjeldahl method as a primary reference procedure for total protein in certified reference materials used in clinical chemistry. II. Selection of direct Kjeldahl analysis and its preliminary performance parameters.

Science.gov (United States)

Vinklárková, Bára; Chromý, Vratislav; Šprongl, Luděk; Bittová, Miroslava; Rikanová, Milena; Ohnútková, Ivana; Žaludová, Lenka

2015-01-01

To select a Kjeldahl procedure suitable for the determination of total protein in reference materials used in laboratory medicine, we reviewed in our previous article Kjeldahl methods adopted by clinical chemistry and found an indirect two-step analysis by total Kjeldahl nitrogen corrected for its nonprotein nitrogen and a direct analysis made on isolated protein precipitates. In this article, we compare both procedures on various reference materials. An indirect Kjeldahl method gave falsely lower results than a direct analysis. Preliminary performance parameters qualify the direct Kjeldahl analysis as a suitable primary reference procedure for the certification of total protein in reference laboratories.

Discussion on environment control technology of escaping cavern to uranium mines

International Nuclear Information System (INIS)

Cao Yongkai

2012-01-01

As the important refuge of Uranium Mines, the environment of Escaping Cavern is important to the miner's life. In order to attain the standard of Environment Control, the paper gave the method of Environment Control to the fire danger, pervious, collapse; Gave the isolating prevention time; represented the scheme of compressed-air self-help system, high pressure oxygen system, emergency oxygen system; Introduced the air purge equipment to handle the CO, CO 2 , bacterium and other harmful gas. At the same time, gave the method to control the temperature with the phase-change materials and private prevention. (author)

Leukoaraiosis significantly worsens driving performance of ordinary older drivers.

Directory of Open Access Journals (Sweden)

Kimihiko Nakano

Full Text Available BACKGROUND: Leukoaraiosis is defined as extracellular space caused mainly by atherosclerotic or demyelinated changes in the brain tissue and is commonly found in the brains of healthy older people. A significant association between leukoaraiosis and traffic crashes was reported in our previous study; however, the reason for this is still unclear. METHOD: This paper presents a comprehensive evaluation of driving performance in ordinary older drivers with leukoaraiosis. First, the degree of leukoaraiosis was examined in 33 participants, who underwent an actual-vehicle driving examination on a standard driving course, and a driver skill rating was also collected while the driver carried out a paced auditory serial addition test, which is a calculating task given verbally. At the same time, a steering entropy method was used to estimate steering operation performance. RESULTS: The experimental results indicated that a normal older driver with leukoaraiosis was readily affected by external disturbances and made more operation errors and steered less smoothly than one without leukoaraiosis during driving; at the same time, their steering skill significantly deteriorated. CONCLUSIONS: Leukoaraiosis worsens the driving performance of older drivers because of their increased vulnerability to distraction.

Bacterial population in traditional sourdough evaluated by molecular methods.

Science.gov (United States)

Randazzo, C L; Heilig, H; Restuccia, C; Giudici, P; Caggia, C

2005-01-01

To study the microbial communities in artisanal sourdoughs, manufactured by traditional procedure in different areas of Sicily, and to evaluate the lactic acid bacteria (LAB) population by classical and culture-independent approaches. Forty-five LAB isolates were identified both by phenotypic and molecular methods. The restriction fragment length polymorphism and 16S ribosomal DNA gene sequencing gave evidence of a variety of species with the dominance of Lactobacillus sanfranciscensis and Lactobacillus pentosus, in all sourdoughs tested. Culture-independent method, such as denaturing gradient gel electrophoresis (DGGE) of the V6-V8 regions of the 16S rDNA, was applied for microbial community fingerprint. The DGGE profiles revealed the dominance of L. sanfranciscensis species. In addition, Lactobacillus-specific primers were used to amplify the V1-V3 regions of the 16S rDNA. DGGE profiles flourished the dominance of L. sanfranciscensis and Lactobacillus fermentum in the traditional sourdoughs, and revealed that the closely related species Lactobacillus kimchii and Lactobacillus alimentarius were not discriminated. Lactobacillus-specific PCR-DGGE analysis is a rapid tool for rapid detection of Lactobacillus species in artisanal sourdough. This study reports a characterization of Lactobacillus isolates from artisanal sourdoughs and highlights the value of DGGE approach to detect uncultivable Lactobacillus species.

Meta-analytic methods for pooling rates when follow-up duration varies: a case study.

Science.gov (United States)

Guevara, James P; Berlin, Jesse A; Wolf, Fredric M

2004-07-12

Meta-analysis can be used to pool rate measures across studies, but challenges arise when follow-up duration varies. Our objective was to compare different statistical approaches for pooling count data of varying follow-up times in terms of estimates of effect, precision, and clinical interpretability. We examined data from a published Cochrane Review of asthma self-management education in children. We selected two rate measures with the largest number of contributing studies: school absences and emergency room (ER) visits. We estimated fixed- and random-effects standardized weighted mean differences (SMD), stratified incidence rate differences (IRD), and stratified incidence rate ratios (IRR). We also fit Poisson regression models, which allowed for further adjustment for clustering by study. For both outcomes, all methods gave qualitatively similar estimates of effect in favor of the intervention. For school absences, SMD showed modest results in favor of the intervention (SMD -0.14, 95% CI -0.23 to -0.04). IRD implied that the intervention reduced school absences by 1.8 days per year (IRD -0.15 days/child-month, 95% CI -0.19 to -0.11), while IRR suggested a 14% reduction in absences (IRR 0.86, 95% CI 0.83 to 0.90). For ER visits, SMD showed a modest benefit in favor of the intervention (SMD -0.27, 95% CI: -0.45 to -0.09). IRD implied that the intervention reduced ER visits by 1 visit every 2 years (IRD -0.04 visits/child-month, 95% CI: -0.05 to -0.03), while IRR suggested a 34% reduction in ER visits (IRR 0.66, 95% CI 0.59 to 0.74). In Poisson models, adjustment for clustering lowered the precision of the estimates relative to stratified IRR results. For ER visits but not school absences, failure to incorporate study indicators resulted in a different estimate of effect (unadjusted IRR 0.77, 95% CI 0.59 to 0.99). Choice of method among the ones presented had little effect on inference but affected the clinical interpretability of the findings. Incidence rate

Quantification of rat brain SPECT with 123I-ioflupane: evaluation of different reconstruction methods and image degradation compensations using Monte Carlo simulation

International Nuclear Information System (INIS)

Roé-Vellvé, N; Pino, F; Cot, A; Ros, D; Falcon, C; Gispert, J D; Pavía, J; Marin, C

2014-01-01

SPECT studies with 123 I-ioflupane facilitate the diagnosis of Parkinson’s disease (PD). The effect on quantification of image degradations has been extensively evaluated in human studies but their impact on studies of experimental PD models is still unclear. The aim of this work was to assess the effect of compensating for the degrading phenomena on the quantification of small animal SPECT studies using 123 I-ioflupane. This assessment enabled us to evaluate the feasibility of quantitatively detecting small pathological changes using different reconstruction methods and levels of compensation for the image degrading phenomena. Monte Carlo simulated studies of a rat phantom were reconstructed and quantified. Compensations for point spread function (PSF), scattering, attenuation and partial volume effect were progressively included in the quantification protocol. A linear relationship was found between calculated and simulated specific uptake ratio (SUR) in all cases. In order to significantly distinguish disease stages, noise-reduction during the reconstruction process was the most relevant factor, followed by PSF compensation. The smallest detectable SUR interval was determined by biological variability rather than by image degradations or coregistration errors. The quantification methods that gave the best results allowed us to distinguish PD stages with SUR values that are as close as 0.5 using groups of six rats to represent each stage. (paper)

High-performance liquid chromatography method validation for determination of tetracycline residues in poultry meat

Directory of Open Access Journals (Sweden)

Vikas Gupta

2014-01-01

Full Text Available Background: In this study, a method for determination of tetracycline (TC residues in poultry with the help of high-performance liquid chromatography technique was validated. Materials and Methods: The principle step involved in ultrasonic-assisted extraction of TCs from poultry samples by 2 ml of 20% trichloroacetic acid and phosphate buffer (pH 4, which gave a clearer supernatant and high recovery, followed by centrifugation and purification by using 0.22 μm filter paper. Results: Validity study of the method revealed that all obtained calibration curves showed good linearity (r2 > 0.999 over the range of 40-4500 ng. Sensitivity was found to be 1.54 and 1.80 ng for oxytetracycline (OTC and TC. Accuracy was in the range of 87.94-96.20% and 72.40-79.84% for meat. Precision was lower than 10% in all cases indicating that the method can be used as a validated method. Limit of detection was found to be 4.8 and 5.10 ng for OTC and TC, respectively. The corresponding values of limit of quantitation were 11 and 12 ng. Conclusion: The method reliably identifies and quantifies the selected TC and OTC in the reconstituted poultry meat in the low and sub-nanogram range and can be applied in any laboratory.

The Effect of Combination Carrot Juice (Daucus carota L. and Hunkwee Flour in Manufacturing Kefir Ice Cream on Physical and Chemical Quality of Kefir Ice Cream

Directory of Open Access Journals (Sweden)

Ilma Mahdiana

2017-03-01

Full Text Available The purpose of this research was to determine the best combination of carrot juice (CJ and hunkwee flour (HF on manufacturing of kefir ice cream. The method of this research was experiment with Completely Randomized Design, 4 treatments and 4 replication, the treatments were without carrot juice + HF 5% (P0, CJ 1.5% + HF 3.5% (P1, CJ 3% + HF 2% (P2, CJ 4.5% + HF 0.5% (P3, the presentage based on Ice Cream Mix (ICM. The variables measured were antioxidant activity, viscosity, total solid and organoleptic (textur, taste and aroma. The data was analized by using Analysis Of Variance (ANOVA continued by Honestly Significance Difference (HSD test. The result of this research showed that the combination of carrot juice and hunkwee flour gave highly significant difference effect (P0.05 on aroma. Conclusion: the combination of carrot juice 1.5% + hunkwee flour 3.5% (P1 in kefir ice cream gave the best result.

Evaluation of health care service quality in Poland with the use of SERVQUAL method at the specialist ambulatory health care center.

Science.gov (United States)

Manulik, Stanisław; Rosińczuk, Joanna; Karniej, Piotr

2016-01-01

Service quality and customer satisfaction are very important components of competitive advantage in the health care sector. The SERVQUAL method is widely used for assessing the quality expected by patients and the quality of actually provided services. The main purpose of this study was to determine if patients from state and private health care facilities differed in terms of their qualitative priorities and assessments of received services. The study included a total of 412 patients: 211 treated at a state facility and 201 treated at a private facility. Each of the respondents completed a 5-domain, 22-item SERVQUAL questionnaire. The actual quality of health care services in both types of facilities proved significantly lower than expected. All the patients gave the highest scores to the domains constituting the core aspects of health care services. The private facility respondents had the highest expectations with regard to equipment, and the state facility ones regarding contacts with the medical personnel. Health care quality management should be oriented toward comprehensive optimization in all domains, rather than only within the domain identified as the qualitative priority for patients of a given facility.

HDL-LDL Ratio: A Significant Predisposition to the Onset of ...

African Journals Online (AJOL)

The significance of high-density lipoprotein/low density lipoprotein (HDL-LDL) ratio as a predisposing factor to the onset of atherogenesis has been studied. Standard enzymatic method using Cholesterol kit to extract cholesterol was used. HDL was analysed using standard HDL Kit and LDL concentration was derived by a ...

Community Mining Method of Label Propagation Based on Dense Pairs

Directory of Open Access Journals (Sweden)

WENG Wei

2014-03-01

Full Text Available In recent years, with the popularity of handheld Internet equipments like mobile phones, increasing numbers of people are becoming involved in the virtual social network. Because of its large amount of data and complex structure, the network faces new challenges of community mining. A label propagation algorithm with low time complexity and without prior parameters deals easily with a large networks. This study explored a new method of community mining, based on label propagation with two stages. The first stage involved identifying closely linked nodes according to their local adjacency relations that gave rise to a micro-community. The second stage involved expanding and adjusting this community through a label propagation algorithm (LPA to finally obtain the community structure of the entire social network. This algorithm reduced the number of initial labels and avoided the merging of small communities in general LPAs. Thus, the quality of community discovery was improved, and the linear time complexity of the LPA was maintained.

Imagining the Music: Methods for Assessing Musical Imagery Ability

Science.gov (United States)

Clark, Terry; Williamon, Aaron

2012-01-01

Timing profiles of live and imagined performances were compared with the aim of creating a context-specific measure of musicians' imagery ability. Thirty-two advanced musicians completed imagery use and vividness surveys, and then gave two live and two mental performances of a two-minute musical excerpt, tapping along with the beat of the mental…

Application of measuring 99mTc-MAG3 plasma clearance based on one-compartment model (MPC method) to pediatric patients

International Nuclear Information System (INIS)

Koizumi, Kiyoshi; Higashida, Kousuke; Arbab, A.S.; Toyama, Keiji; Arai, Takao; Yoshitomi, Tatsuya.

1997-01-01

Measurement of 99m Tc-MAG3 plasma clearance based on 1-compartment model (MPC method) were applied to 12 pediatric patients and evaluated for the factors which might affect the calculated results. Depth correction is a critical factor for the measurement of renal uptake. Three different equations for estimating renal depth were compared with the real depth measured by ultrasonography. The equation proposed by K. Itoh was suitable though the equations by T. Ito and Raynaud were insufficient. Estimation of distribution volume, which is regarded as circulating plasma volume (CPV), is also critical for the calculation of MAG3 clearance by MPC method. Precisely, hematocrit measured by venous sampling and circulating blood volume (CBV) calculated as 7.5% of body weight are used for estimation of CPV. However, assumed CPV as 5% of body weight was acceptable if the hematocrit was not severely deviated from the normal value. Simplified MPC method utilizing two factors mentioned above gave a positive correlation with Russell's one point sampling method. In conclusion, MPC method is applicable for pediatric patients. (author)

“He Gave Me the Words”: An Interview with Raoul Peck

Directory of Open Access Journals (Sweden)

Leah Mirakhor

2017-10-01

Additionally, we discussed a series of aesthetic choices he fought to include in the film’s final cut, directing Samuel L. Jackson as the voice for the film, the similarities and shifts he wanted to document in American culture since the 1960s, and some of the criticism he has received for not emphasizing more Baldwin’s sexuality.

Når døde børn er livets gave

DEFF Research Database (Denmark)

Jensen, Anja Marie Bornø

2008-01-01

Det er kvinder, især mødre til organdonorer, der gennem en særlig praktisering af “moderskab” sætter dagsordenen for den organisatoriske støtte og opfølgning, der tilbydes alle pårørende til organdonorer i USA i tiden efter samtykket til organdonation. Men hvordan kommer dette partikulære modersk...

The prevalence and screening methods of postpartum depression

Directory of Open Access Journals (Sweden)

Özgür Erdem

2012-09-01

Full Text Available Postpartum Depression is the most common complicationof the delivery and affects approximately 10%-15% ofwomen who had just gave birth. During a period in whichwomen believe that they should be happy, the depressivemood experienced by most women leads to feelings ofguilt, hiding the symptoms, and postpartum depressionto be overlooked. Although the incidence of serious psychiatricdisorders during pregnancy is low, it is reportedthat the incidence shows a dramatic increase during thepostpartum period and this risky period may continue upto six months, one year or even two years.As the onset of postpartum depression is insidious it caneasily be overlooked if the patient’s seeking help is notsupported, especially when the severity of postpartum depressionis mild or moderate. In these cases, postpartumdepression may persist for a long time and at last it can beso severe that hospitalization would be needed. Therefore,early diagnose is very important and primary carephysicians and other health care workers should be alert.Postpartum Depression should be diagnosed using reliabledescriptive methods in puerperant women. Thescales such as Postnatal Depression Screening Scale,Beck Depression Inventory, Edinburgh Postnatal DepressionScale and State-Trait Anxiety Inventory, all of whichwere tested for validity and reliability in our country can beused during follow-up of pregnant and puerperal women.Key words: Postpartum depression, screening methods,primary health care professionals

Prognostic significance of cytosolic pS2 content in ovarian tumors

International Nuclear Information System (INIS)

Raigoso, P.; Allende, T.; Zeidan, N.; Llana, B.; Bernardo, L.; Roiz, C.; Tejuca, S.; Vazquez, J.; Lamelas, M.L.

2002-01-01

Aim: pS2 is an estrogen regulated peptide which has been associated with a good prognosis an with a more favorable response to treatment in breast cancer patients. In ovarian tumors, the expression of pS2 was demonstrated at both mRNA and protein levels. In addition, it has been showed significant association of pS2 with mucinous differentiation or well differentiation grade of the tumors. However, it is little know about the prognostic significance of the pS2 content in ovarian carcinomas. The aims of the present work were to analyze the cytosolic pS2 content in benign and malignant ovarian tumors, its relationship with clinico-pathologic parameters, steroid receptor status, and prognostic significance. Material and Methods: We analysed the cytosolic concentrations of pS2 in 91 specimen ovarian tissues by an immunoradiometric assay (ELSA-pS2, CIS, France). The tissues were 8 normal ovaries, 43 benign tumors and 40 malignant ovarian tumors. The same ovarian tissues processed to pS2 were analyzed to Estrogen (ER) and Progesterone (PgR) Receptor status. These steroid receptors were quantified biochemically following commercial ELISA method (ABBOTT Diagnostics, Germany). The relationship between cytosolic content and clinico-pathologic factors was examined by the Mann-Whitney or Kruskall-Wallis test. Correlation between steroid receptors and pS2 content was calculated with the Spearman test. Survival curves were calculated using the Kaplan-Meier method and compared by the log-rank test. Differences were considered significant at 5% probability level. Results: pS2 could be detected in 30 cases (32.9%) with values ranged from 0.04 to 89 ng/mg prt. Only one normal ovary showed detectable levels of pS2 and there were not differences in cytosolic content between benign and malignant ovarian tumors. The pS2 levels were only associated to mucinous differentiation in both benign and malignant ovarian tumors (p=0.029 and p=0.015, respectively). Significantly higher

Meta-analyses triggered by previous (false-)significant findings : Problems and solutions

NARCIS (Netherlands)

Schuit, Ewoud; Roes, Kit C B; Mol, Ben W J; Kwee, Anneke; Moons, Karel G M; Groenwold, Rolf H H

2015-01-01

BACKGROUND: Meta-analyses are typically triggered by a (potentially false-significant) finding in one of the preceding primary studies. We studied consequences of meta-analysis investigating effects when primary studies that triggered such meta-analysis are also included. METHODS: We analytically

In-line analytical methods for fuel reprocessing streams : Part IV -Neutron monitoring for plutonium

International Nuclear Information System (INIS)

Rao, V.K.; Bhargava, V.K.; Marathe, S.G.; Iyer, R.H.; Ramaniah, M.V.; Srinivasan, N.

1975-01-01

A neutron monitoring assembly consisting of a stainless steel housing packed with beryllium oxide chips, a paraffin moderator, a ring of fifteen BF 3 counters and an all stainless steel continuous flow system for circulating plutonium solutions has been fabricated and tested for monitoring plutonium concentrations in flow solutions. The method is based on the detection and measurement of neutron flux produced when alpha particles from plutonium interact with beryllium by the nuclear reactoon 9 4 Be(α,n) 12 6 C. The unit was successfully tested for the estimation of plutonium concentrations upto 10 g/1 in solutions of plutonium and plutonium solutions mixed with uranium and fission products. The unit gave an accuracy of 10-15%. Details of the construction and working of the system are discussed. (author)

Statistical Significance for Hierarchical Clustering

Science.gov (United States)

Kimes, Patrick K.; Liu, Yufeng; Hayes, D. Neil; Marron, J. S.

2017-01-01

Summary Cluster analysis has proved to be an invaluable tool for the exploratory and unsupervised analysis of high dimensional datasets. Among methods for clustering, hierarchical approaches have enjoyed substantial popularity in genomics and other fields for their ability to simultaneously uncover multiple layers of clustering structure. A critical and challenging question in cluster analysis is whether the identified clusters represent important underlying structure or are artifacts of natural sampling variation. Few approaches have been proposed for addressing this problem in the context of hierarchical clustering, for which the problem is further complicated by the natural tree structure of the partition, and the multiplicity of tests required to parse the layers of nested clusters. In this paper, we propose a Monte Carlo based approach for testing statistical significance in hierarchical clustering which addresses these issues. The approach is implemented as a sequential testing procedure guaranteeing control of the family-wise error rate. Theoretical justification is provided for our approach, and its power to detect true clustering structure is illustrated through several simulation studies and applications to two cancer gene expression datasets. PMID:28099990

The prognostic significance of parapharyngeal tumour involvement in nasopharyngeal carcinoma

International Nuclear Information System (INIS)

Teo, P.Y.; Lee, W.; Yu, P.

1996-01-01

From 1984 to 1989, 903 treatment-naive non-disseminated nasopharyngeal carcinomas (NPCs) were given primary radical radiotherapy. All patients had computed tomographic and endoscopic evaluation of the primary tumour. Potentially significant parameters were analysed by both univariate and multivariate methods for independent significance. In the whole group of patients, the male sex, skull base and cranial nerve(s) involvement, advanced Ho N-level, presence of fixed or partially fixed nodes and nodes contralateral to the side of the bulk of the nasopharyngeal primary, significantly determined survival and distant metastasis rates, whereas skull base and cranial nerve involvement, advanced age and male sex significantly worsened local control. However in the Ho T2No subgroup, parapharyngeal tumour involvement was the most significant prognosticator that determined distant metastasis and survival rates in the absence of the overriding prognosticators of skull base infiltration, cranial nerve(s) palsy, and cervical nodal metastasis. The local tumour control of the Ho T2No was adversely affected by the presence of oropharyngeal tumour extension. The administration of booster radiotherapy (20 Gy) after conventional radiotherapy (60-62.5 Gy) in tumours with parapharyngeal involvement has led to an improvement in local control, short of statistical significance

Microcalorimetric measurements of heat production in human erythrocytes. IV. Comparison between different calorimetric techniques, suspension media, and preparation methods.

Science.gov (United States)

Monti, M; Wadsö, I

1976-10-01

Heat production in human erythrocytes from healthy subjects has been measured under different experimental conditions. Simultaneous measurements were made on the same samples using different types of microcalorimeters: a static ampoule calorimeter, an air perfusion calorimeter, and a flow calorimeter. Obtained heat effect values for specified standard conditions, P degrees, were within uncertainty limits the same for the different calorimeters. Cells were suspended either in autologous plasma or in a phosphate buffer. P degrees values for buffer suspensions were significantly higher than those for plasma suspensions. Erythrocyte samples prepared by the column adsorption technique gave higher P degrees values than those obtained by a conventional centrifugation procedure.

Method of reducing radon levels in buildings

International Nuclear Information System (INIS)

Khajdarov, R.A.; Gapurova, O.U.; Khajdarov, R.R.

2004-01-01

Radon concentration can be reduced by using polymeric compositions which fill pores inside building materials and decrease the coefficient of permeation of radon atoms and water molecules in building materials (concrete, gypsum, etc.). Polymeric silico-organic compounds were investigated and selected as the chemicals to prevent radon seeping indoors. Gas (air, Ar, 222 Rn, H 2 O) permeability of concrete and gypsum after treatment with chemicals was examined. The effect of the cement and sand types, preliminary treatment with various chemicals, type of the polymeric silico-organic compounds, time between treatments, moisture of concrete, time between the preparation of chemicals and the treatment of concrete (ageing of chemicals), time between the treatment of concrete and testing (ageing of treated concrete) were examined. Surfaces of the samples were treated by spraying. The experiments gave evidence that the chosen method of treatment of the construction materials allows reducing the coefficient of gas permeability in 200 - 400 times. Treatment of the floor, walls and ceiling of the basement of 5 buildings reduced the radon concentration in the premises of the first floor from 400-600 Bq/m 3 to the background value of 17-20 Bq/m 3

Significance of serum endostatin levels in patients with primary lung cancer

International Nuclear Information System (INIS)

Peng Qunxin; Ling Chunhua; Ji Cheng

2005-01-01

Objective: To investigate the relationship between the serum level of endostatin and the clinical pathophysiological characteristics in patients with primary lung cancer. Methods: The serum levels of endostatin were detected in 48 patients with primary lung cancer and 50 patients with benign pulmonary diseases by enzyme-linked immunosorbent assay (ELISA) method. Results: Serum endostatin level in patients with primary lung cancer was significantly higher than it in patients with benign pulmonary diseases (P<0.01). It was higher in adenocarcinoma group than that in squamous cell carcinoma and small cell carcinoma group (P<0.05). The level of serum endostatin in lung cancer with TNM stage III + IV was higher than that in patients in stage I + II (P<0.01). And it was also higher in patients suffering from lung cancer with metastasis than that in patients with no metastasis (P<0.05). However, there was not a significant relation between serum endostatin level the location of the tumor and lymph node metastasis. Conclusion: Serum endostatin level in expressed higher in patients with primary lung cancer. There is significant relationship between serum endostatin level, histological classification, TNM stage and metastasis of lung cancer. (authors)