WorldWideScience

Sample records for methodology trim air

  1. Pemanfaatan trimming kulit pikel sebagai flokulan melalui hidrolisis kolagen menggunakan basa untuk penjernihan air

    Directory of Open Access Journals (Sweden)

    Sugihartono

    2015-07-01

    Full Text Available Wastes in the form of skin derivatives from leather tanning industries remain serious problems if not managed properly and quickly, since they can cause environmental pollution. This research aimed at studying the influence of base type and concentration for the hydrolysis of trimmed collagen from pickled sheepskin to the yield and properties of gelatin, as well as the gelatin’s potential as flocculant. The hydrolysis of trimmed collagen from pickled sheepskin was performed using KOH or NaOH solution, each with varied concentrations of 1, 2, 3, and 4% w/v, for 16 hours. The extraction of the resulting gelatin was performed using water (2.5 water part : 1 waste part, at 70-80 oC, for 3 hours. The results show that the yield of gelatin from hydrolysis using KOH (16.50-28.60% is lower than that using NaOH (23.68-34.42%. The water and fat contents of the resulting gelatin were relatively similar, while the protein content from KOH treatment was higher than that from NaOH treatment. Hydrolysis with KOH 1% and NaOH 1% and 2% resulted in gelatin that can be used as flocculant. Hydrolysis with NaOH 2% was the best treatment to produce gelatin as flocculant.

  2. Air pollution monitoring - a methodological approach

    International Nuclear Information System (INIS)

    Trajkovska Trpevska, Magdalena

    2002-01-01

    Methodology for monitoring the emission of polluters in the air is a complex concept that in general embraces following fazes: sampling, laboratory treatment, and interpretation of results. In Company for technological and laboratory investigation and environmental protection - Mining Institute Skopje, the control of emission of polluters in the air is performing according methodology based in general on the recommendation of standard VDI 2.066 prescribe from Ministry of Ecology in Germany, because adequate legislation in our country does not exist. In this article the basic treatment of methodology for the air polluters emission control is presented. (Original)

  3. Air quality estimation by computational intelligence methodologies

    Directory of Open Access Journals (Sweden)

    Ćirić Ivan T.

    2012-01-01

    Full Text Available The subject of this study is to compare different computational intelligence methodologies based on artificial neural networks used for forecasting an air quality parameter - the emission of CO2, in the city of Niš. Firstly, inputs of the CO2 emission estimator are analyzed and their measurement is explained. It is known that the traffic is the single largest emitter of CO2 in Europe. Therefore, a proper treatment of this component of pollution is very important for precise estimation of emission levels. With this in mind, measurements of traffic frequency and CO2 concentration were carried out at critical intersections in the city, as well as the monitoring of a vehicle direction at the crossroad. Finally, based on experimental data, different soft computing estimators were developed, such as feed forward neural network, recurrent neural network, and hybrid neuro-fuzzy estimator of CO2 emission levels. Test data for some characteristic cases presented at the end of the paper shows good agreement of developed estimator outputs with experimental data. Presented results are a true indicator of the implemented method usability. [Projekat Ministarstva nauke Republike Srbije, br. III42008-2/2011: Evaluation of Energy Performances and br. TR35016/2011: Indoor Environment Quality of Educational Buildings in Serbia with Impact to Health and Research of MHD Flows around the Bodies, in the Tip Clearances and Channels and Application in the MHD Pumps Development

  4. Assessment methodology for air defence control systems

    CSIR Research Space (South Africa)

    Oosthuizen, R

    2013-09-01

    Full Text Available In Command and Control, humans have to make sense of the situation to support decision making on the required action. Development of an Air Defence Control system through a Systems Engineering process starts with assessment of existing systems...

  5. NCSX Trim Coil Design

    International Nuclear Information System (INIS)

    Kalish, M.; Brooks, A.; Rushinski, J.; Upcavage, R.

    2009-01-01

    The National Compact Stellarator Experiment (NCSX) was being constructed at the Princeton Plasma Physics Laboratory in partnership with Oak Ridge National Laboratory before work was stopped in 2008. The objective of this experiment was to develop the stellarator concept and evaluate it's potential as a model for future fusion power plants. Stellarator design requires very precisely positioned Modular Coils of complex shape to form 3D plasmas. In the design of NCSX, Trim Coils were required to compensate for both the positioning of the coils during assembly and the fabrication tolerances of the Modular Coils. Use of the Trim Coils allowed for larger tolerances increasing ease of assembly and decreasing overall cost. A set of Trim coils was developed to suppress the toroidal flux in island regions due to misalignment, magnetic materials, and eddy currents. The requirement imposed upon the design forced the toroidal flux in island regions below 10% of the total toroidal flux in the plasma. An analysis was first performed to evaluate candidate Trim Coil configurations iterating both the size, number, and position of the coils. The design was optimized considering both performance and cost while staying within the tight restraints presented by the space limited geometry. The final design of the Trim Coils incorporated a 48 Coil top bottom symmetric set. Fabrication costs were minimized by having only two coil types and using a planar conventional design with off the shelf commercial conductor. The Trim Coil design incorporated supports made from simple structural shapes assembled together in a way which allowed for adjustment as well as accommodation for the tolerance build up on the mating surfaces. This paper will summarize the analysis that led to the optimization of the Trim Coils set, the trim coil mechanical design, thermal and stress analysis, and the design of the supporting Trim Coil structure

  6. Major Upgrades to the AIRS Version-6 Ozone Profile Methodology

    Science.gov (United States)

    Susskind, Joel; Blaisdell, John; Iredell, Lena

    2015-01-01

    This research is a continuation of part of what was shown at the last AIRS Science Team Meeting in the talk Improved Water Vapor and Ozone Profiles in SRT AIRS Version-6.X and the AIRS February 11, 2015 NetMeeting Further improvements in water vapor and ozone profiles compared to Version-6.AIRS Version-6 was finalized in late 2012 and is now operational. Version-6 contained many significant improvements in retrieval methodology compared to Version-5. However, Version-6 retrieval methodology used for the water vapor profile q(p) and ozone profile O3(p) retrievals is basically unchanged from Version-5, or even from Version-4. Subsequent research has made significant improvements in both water vapor and O3 profiles compared to Version-6. This talk will concentrate on O3 profile retrievals. Improvements in water vapor profile retrievals are given in a separate presentation.

  7. Methodological issues in studies of air pollution and reproductive health.

    Science.gov (United States)

    Woodruff, Tracey J; Parker, Jennifer D; Darrow, Lyndsey A; Slama, Rémy; Bell, Michelle L; Choi, Hyunok; Glinianaia, Svetlana; Hoggatt, Katherine J; Karr, Catherine J; Lobdell, Danelle T; Wilhelm, Michelle

    2009-04-01

    In the past decade there have been an increasing number of scientific studies describing possible effects of air pollution on perinatal health. These papers have mostly focused on commonly monitored air pollutants, primarily ozone (O(3)), particulate matter (PM), sulfur dioxide (SO(2)), carbon monoxide (CO), and nitrogen dioxide (NO(2)), and various indices of perinatal health, including fetal growth, pregnancy duration, and infant mortality. While most published studies have found some marker of air pollution related to some types of perinatal outcomes, variability exists in the nature of the pollutants and outcomes associated. Synthesis of the findings has been difficult for various reasons, including differences in study design and analysis. A workshop was held in September 2007 to discuss methodological differences in the published studies as a basis for understanding differences in study findings and to identify priorities for future research, including novel approaches for existing data. Four broad topic areas were considered: confounding and effect modification, spatial and temporal exposure variations, vulnerable windows of exposure, and multiple pollutants. Here we present a synopsis of the methodological issues and challenges in each area and make recommendations for future study. Two key recommendations include: (1) parallel analyses of existing data sets using a standardized methodological approach to disentangle true differences in associations from methodological differences among studies; and (2) identification of animal studies to inform important mechanistic research gaps. This work is of critical public health importance because of widespread exposure and because perinatal outcomes are important markers of future child and adult health.

  8. METHODOLOGY FOR ANALYSIS OF DECISION MAKING IN AIR NAVIGATION SYSTEM

    Directory of Open Access Journals (Sweden)

    Volodymyr Kharchenko

    2011-03-01

    Full Text Available Abstract. In the research of Air Navigation System as a complex socio-technical system the methodologyof analysis of human-operator's decision-making has been developed. The significance of individualpsychologicalfactors as well as the impact of socio-psychological factors on the professional activities of ahuman-operator during the flight situation development from normal to catastrophic were analyzed. On thebasis of the reflexive theory of bipolar choice the expected risks of decision-making by the Air NavigationSystem's operator influenced by external environment, previous experience and intentions were identified.The methods for analysis of decision-making by the human-operator of Air Navigation System usingstochastic networks have been developed.Keywords: Air Navigation System, bipolar choice, human operator, decision-making, expected risk, individualpsychologicalfactors, methodology of analysis, reflexive model, socio-psychological factors, stochastic network.

  9. Trim coil power supplies

    International Nuclear Information System (INIS)

    Haisler, R.; Peeler, H.; Zajicek, W.

    1985-01-01

    The 18 trim coil power supplies have been constructed and are now in place in the K500 pit and pit mezzanine. Final wiring of the primary power and control power is proceeding along with installation of cooling water supplies. The supplies are expected to be ready for final testing into resistive loads at the beginning of June, 1985

  10. Integral Design Methodology of Photocatalytic Reactors for Air Pollution Remediation

    Directory of Open Access Journals (Sweden)

    Claudio Passalía

    2017-06-01

    Full Text Available An integral reactor design methodology was developed to address the optimal design of photocatalytic wall reactors to be used in air pollution control. For a target pollutant to be eliminated from an air stream, the proposed methodology is initiated with a mechanistic derived reaction rate. The determination of intrinsic kinetic parameters is associated with the use of a simple geometry laboratory scale reactor, operation under kinetic control and a uniform incident radiation flux, which allows computing the local superficial rate of photon absorption. Thus, a simple model can describe the mass balance and a solution may be obtained. The kinetic parameters may be estimated by the combination of the mathematical model and the experimental results. The validated intrinsic kinetics obtained may be directly used in the scaling-up of any reactor configuration and size. The bench scale reactor may require the use of complex computational software to obtain the fields of velocity, radiation absorption and species concentration. The complete methodology was successfully applied to the elimination of airborne formaldehyde. The kinetic parameters were determined in a flat plate reactor, whilst a bench scale corrugated wall reactor was used to illustrate the scaling-up methodology. In addition, an optimal folding angle of the corrugated reactor was found using computational fluid dynamics tools.

  11. Different methodologies to quantify uncertainties of air emissions.

    Science.gov (United States)

    Romano, Daniela; Bernetti, Antonella; De Lauretis, Riccardo

    2004-10-01

    Characterization of the uncertainty associated with air emission estimates is of critical importance especially in the compilation of air emission inventories. In this paper, two different theories are discussed and applied to evaluate air emissions uncertainty. In addition to numerical analysis, which is also recommended in the framework of the United Nation Convention on Climate Change guidelines with reference to Monte Carlo and Bootstrap simulation models, fuzzy analysis is also proposed. The methodologies are discussed and applied to an Italian example case study. Air concentration values are measured from two electric power plants: a coal plant, consisting of two boilers and a fuel oil plant, of four boilers; the pollutants considered are sulphur dioxide (SO(2)), nitrogen oxides (NO(X)), carbon monoxide (CO) and particulate matter (PM). Monte Carlo, Bootstrap and fuzzy methods have been applied to estimate uncertainty of these data. Regarding Monte Carlo, the most accurate results apply to Gaussian distributions; a good approximation is also observed for other distributions with almost regular features either positive asymmetrical or negative asymmetrical. Bootstrap, on the other hand, gives a good uncertainty estimation for irregular and asymmetrical distributions. The logic of fuzzy analysis, where data are represented as vague and indefinite in opposition to the traditional conception of neatness, certain classification and exactness of the data, follows a different description. In addition to randomness (stochastic variability) only, fuzzy theory deals with imprecision (vagueness) of data. Fuzzy variance of the data set was calculated; the results cannot be directly compared with empirical data but the overall performance of the theory is analysed. Fuzzy theory may appear more suitable for qualitative reasoning than for a quantitative estimation of uncertainty, but it suits well when little information and few measurements are available and when

  12. Speciated arsenic in air: measurement methodology and risk assessment considerations.

    Science.gov (United States)

    Lewis, Ari S; Reid, Kim R; Pollock, Margaret C; Campleman, Sharan L

    2012-01-01

    Accurate measurement of arsenic (As) in air is critical to providing a more robust understanding of arsenic exposures and associated human health risks. Although there is extensive information available on total arsenic in air, less is known on the relative contribution of each arsenic species. To address this data gap, the authors conducted an in-depth review of available information on speciated arsenic in air. The evaluation included the type of species measured and the relative abundance, as well as an analysis of the limitations of current analytical methods. Despite inherent differences in the procedures, most techniques effectively separated arsenic species in the air samples. Common analytical techniques such as inductively coupled plasma mass spectrometry (ICP-MS) and/or hydride generation (HG)- or quartz furnace (GF)-atomic absorption spectrometry (AAS) were used for arsenic measurement in the extracts, and provided some of the most sensitive detection limits. The current analysis demonstrated that, despite limited comparability among studies due to differences in seasonal factors, study duration, sample collection methods, and analytical methods, research conducted to date is adequate to show that arsenic in air is mainly in the inorganic form. Reported average concentrations of As(III) and As(V) ranged up to 7.4 and 10.4 ng/m3, respectively, with As(V) being more prevalent than As(III) in most studies. Concentrations of the organic methylated arsenic compounds are negligible (in the pg/m3 range). However because of the variability in study methods and measurement methodology, the authors were unable to determine the variation in arsenic composition as a function of source or particulate matter (PM) fraction. In this work, the authors include the implications of arsenic speciation in air on potential exposure and risks. The authors conclude that it is important to synchronize sample collection, preparation, and analytical techniques in order to generate

  13. Multicriteria methodological approach to manage urban air pollution

    Science.gov (United States)

    Vlachokostas, Ch.; Achillas, Ch.; Moussiopoulos, N.; Banias, G.

    2011-08-01

    Managing urban air pollution necessitates a feasible and efficient abatement strategy which is characterised as a defined set of specific control measures. In practice, hard budget constraints are present in any decision-making process and therefore available alternatives need to be hierarchised in a fast but still reliable manner. Moreover, realistic strategies require adequate information on the available control measures, taking also into account the area's special characteristics. The selection of the most applicable bundle of measures rests in achieving stakeholders' consensus, while taking into consideration mutually conflicting views and criteria. A preliminary qualitative comparison of alternative control measures would be most handy for decision-makers, forming the grounds for an in-depth analysis of the most promising ones. This paper presents an easy-to-follow multicriteria methodological approach in order to include and synthesise multi-disciplinary knowledge from various stakeholders so as to result into a priority list of abatement options, achieve consensus and secure the adoption of the resulting optimal solution. The approach relies on the active involvement of public authorities and local stakeholders in order to incorporate their environmental, economic and social preferences. The methodological scheme is implemented for the case of Thessaloniki, Greece, an area considered among the most polluted cities within Europe, especially with respect to airborne particles. Intense police control, natural gas penetration in buildings and metro construction equally result into the most "promising" alternatives in order to control air pollution in the GTA. The three optimal alternatives belong to different thematic areas, namely road transport, thermal heating and infrastructure. Thus, it is obvious that efforts should spread throughout all thematic areas. Natural gas penetration in industrial units, intense monitoring of environmental standards and regular

  14. Effects of varying laser trimming geometries on thin film\\ud resistors

    OpenAIRE

    Alafogianni, Maria; Birkett, Martin; Penlington, Roger

    2017-01-01

    Purpose - This paper studies the effects of varying laser trim patterns on several performance parameters of thin film resistors such as the temperature coefficient of resistance (TCR) and target resistance value.\\ud \\ud Design/methodology/approach - The benefits and limitations of basic trim patterns are taken into consideration and the plunge cut, double plunge cut and the curved L-cut were selected to be modelled and tested experimentally. A computer simulation of the laser trim patterns h...

  15. Methodology for determining criteria for storing spent fuel in air

    International Nuclear Information System (INIS)

    Reid, C.R.; Gilbert, E.R.

    1986-11-01

    Dry storage in an air atmosphere is a method being considered for spent light water reactor (LWR) fuel as an alternative to storage in an inert gas environment. However, methods to predict fuel integrity based on oxidation behavior of the fuel first must be evaluated. The linear cumulative damage method has been proposed as a technique for defining storage criteria. Analysis of limited nonconstant temperature data on nonirradiated fuel samples indicates that this approach yields conservative results for a strictly decreasing-temperature history. On the other hand, the description of damage accumulation in terms of remaining life concepts provides a more general framework for making predictions of failure. Accordingly, a methodology for adapting remaining life concepts to UO 2 oxidation has been developed at Pacific Northwest Laboratory. Both the linear cumulative damage and the remaining life methods were used to predict oxidation results for spent fuel in which the temperature was decreased with time to simulate the temperature history in a dry storage cask. The numerical input to the methods was based on oxidation data generated with nonirradiated UO 2 pellets. The calculated maximum allowable storage temperatures are strongly dependent on the temperature-time profile and emphasize the conservatism inherent in the linear cumulative damage model. Additional nonconstant temperature data for spent fuel are needed to both validate the proposed methods and to predict temperatures applicable to actual spent fuel storage

  16. An Introduction To PC-TRIM.

    Science.gov (United States)

    John R. Mills

    1989-01-01

    The timber resource inventory model (TRIM) has been adapted to run on person al computers. The personal computer version of TRIM (PC-TRIM) is more widely used than its mainframe parent. Errors that existed in previous versions of TRIM have been corrected. Information is presented to help users with program input and output management in the DOS environment, to...

  17. An Integrated Safety Analysis Methodology for Emerging Air Transport Technologies

    Science.gov (United States)

    Kostiuk, Peter F.; Adams, Milton B.; Allinger, Deborah F.; Rosch, Gene; Kuchar, James

    1998-01-01

    The continuing growth of air traffic will place demands on NASA's Air Traffic Management (ATM) system that cannot be accommodated without the creation of significant delays and economic impacts. To deal with this situation, work has begun to develop new approaches to providing a safe and economical air transportation infrastructure. Many of these emerging air transport technologies will represent radically new approaches to ATM, both for ground and air operations.

  18. Designing a Methodology for Future Air Travel Scenarios

    Science.gov (United States)

    Wuebbles, Donald J.; Baughcum, Steven L.; Gerstle, John H.; Edmonds, Jae; Kinnison, Douglas E.; Krull, Nick; Metwally, Munir; Mortlock, Alan; Prather, Michael J.

    1992-01-01

    The growing demand on air travel throughout the world has prompted several proposals for the development of commercial aircraft capable of transporting a large number of passengers at supersonic speeds. Emissions from a projected fleet of such aircraft, referred to as high-speed civil transports (HSCT's), are being studied because of their possible effects on the chemistry and physics of the global atmosphere, in particular, on stratospheric ozone. At the same time, there is growing concern about the effects on ozone from the emissions of current (primarily subsonic) aircraft emissions. Evaluating the potential atmospheric impact of aircraft emissions from HSCT's requires a scientifically sound understanding of where the aircraft fly and under what conditions the aircraft effluents are injected into the atmosphere. A preliminary set of emissions scenarios are presented. These scenarios will be used to understand the sensitivity of environment effects to a range of fleet operations, flight conditions, and aircraft specifications. The baseline specifications for the scenarios are provided: the criteria to be used for developing the scenarios are defined, the required data base for initiating the development of the scenarios is established, and the state of the art for those scenarios that have already been developed is discussed. An important aspect of the assessment will be the evaluation of realistic projections of emissions as a function of both geographical distribution and altitude from an economically viable commercial HSCT fleet. With an assumed introduction date of around the year 2005, it is anticipated that there will be no HSCT aircraft in the global fleet at that time. However, projections show that, by 2015, the HSCT fleet could reach significant size. We assume these projections of HSCT and subsonic fleets for about 2015 can the be used as input to global atmospheric chemistry models to evaluate the impact of the HSCT fleets, relative to an all

  19. An objective methodology for the evaluation of the air quality stations positioning

    International Nuclear Information System (INIS)

    Benassi, A.; Marson, G.; Baraldo, E.; Dalan, F.; Lorenzet, K.; Bellasio, R.; Bianconi, R.

    2006-01-01

    This work describes a methodology for the evaluation of the correct positioning of the monitoring stations of an air quality network. The methodology is based on the Italian legislation, the European Directives and on some technical documents used as guidelines at European level. The paper describes all the assumption on which the methodology is based and the results of its application to the air quality network of Region Veneto (Italy) [it

  20. An Application of the Methodology for Assessment of the Sustainability of Air Transport System

    Science.gov (United States)

    Janic, Milan

    2003-01-01

    An assessment and operationalization of the concept of sustainable air transport system is recognized as an important but complex research, operational and policy task. In the scope of the academic efforts to properly address the problem, this paper aims to assess the sustainability of air transport system. It particular, the paper describes the methodology for assessment of sustainability and its potential application. The methodology consists of the indicator systems, which relate to the air transport system operational, economic, social and environmental dimension of performance. The particular indicator systems are relevant for the particular actors such users (air travellers), air transport operators, aerospace manufacturers, local communities, governmental authorities at different levels (local, national, international), international air transport associations, pressure groups and public. In the scope of application of the methodology, the specific cases are selected to estimate the particular indicators, and thus to assess the system sustainability under given conditions.

  1. A Methodology of Estimation on Air Pollution and Its Health Effects in Large Japanese Cities

    OpenAIRE

    Hirota, Keiko; Shibuya, Satoshi; Sakamoto, Shogo; Kashima, Shigeru

    2012-01-01

    The correlation between air pollution and health effects in large Japanese cities presents a great challenge owing to the limited availability of data on the exposure to pollution, health effects and the uncertainty of mixed causes. A methodology for quantitative relationships (between the emission volume and air quality, and the air quality and health effects) is analysed with a statistical method in this article; the correlation of air pollution reduction policy in Japan from 1974 to 2007. ...

  2. Training Studies with Compressed Air Breathing Apparatus – Methodology, Exercises

    Directory of Open Access Journals (Sweden)

    Buks Roberts

    2015-11-01

    Full Text Available The current article describes topics ranging from the respiratory physiology and the structure of compressed air breathing apparatus to the performance of practical training exercises in an unbreathable environment (hereinafter referred to as UE.

  3. Active Trimming of Hybrid Integrated Circuits

    OpenAIRE

    Németh, P.; Krémer, P.

    1984-01-01

    One of the more important fields of the microelectronics industry is the manufacturing of hybrid integrated circuits.An important part of the manufacturing process is concerned with the trimming of the hybrid integratedl circuits. This article deals with the basic principles of active trimming and introduces a microprocessor controlled trimming machine. By comparing active trimming with passive techniques, it can be shown that the active system has some advantages. This article outlines these...

  4. ExternE transport methodology for external cost evaluation of air pollution

    DEFF Research Database (Denmark)

    Jensen, S. S.; Berkowicz, R.; Brandt, J.

    The report describes how the human exposure estimates based on NERI's human exposure modelling system (AirGIS) can improve the Danish data used for exposure factors in the ExternE Transport methodology. Initially, a brief description of the ExternE Tranport methodology is given and it is summarised...

  5. Proposed methodology for estimating the impact of highway improvements on urban air pollution.

    Science.gov (United States)

    1971-01-01

    The aim of this methodology is to indicate the expected change in ambient air quality in the vicinity of a highway improvement and in the total background level of urban air pollution resulting from the highway improvement. Both the jurisdiction in w...

  6. Health effects of ambient air pollution – recent research development and contemporary methodological challenges

    Directory of Open Access Journals (Sweden)

    Ren Cizao

    2008-11-01

    Full Text Available Abstract Exposure to high levels of air pollution can cause a variety of adverse health outcomes. Air quality in developed countries has been generally improved over the last three decades. However, many recent epidemiological studies have consistently shown positive associations between low-level exposure to air pollution and health outcomes. Thus, adverse health effects of air pollution, even at relatively low levels, remain a public concern. This paper aims to provide an overview of recent research development and contemporary methodological challenges in this field and to identify future research directions for air pollution epidemiological studies.

  7. Improved Temperature Sounding and Quality Control Methodology Using AIRS/AMSU Data: The AIRS Science Team Version 5 Retrieval Algorithm

    Science.gov (United States)

    Susskind, Joel; Blaisdell, John M.; Iredell, Lena; Keita, Fricky

    2009-01-01

    This paper describes the AIRS Science Team Version 5 retrieval algorithm in terms of its three most significant improvements over the methodology used in the AIRS Science Team Version 4 retrieval algorithm. Improved physics in Version 5 allows for use of AIRS clear column radiances in the entire 4.3 micron CO2 absorption band in the retrieval of temperature profiles T(p) during both day and night. Tropospheric sounding 15 micron CO2 observations are now used primarily in the generation of clear column radiances .R(sub i) for all channels. This new approach allows for the generation of more accurate values of .R(sub i) and T(p) under most cloud conditions. Secondly, Version 5 contains a new methodology to provide accurate case-by-case error estimates for retrieved geophysical parameters and for channel-by-channel clear column radiances. Thresholds of these error estimates are used in a new approach for Quality Control. Finally, Version 5 also contains for the first time an approach to provide AIRS soundings in partially cloudy conditions that does not require use of any microwave data. This new AIRS Only sounding methodology, referred to as AIRS Version 5 AO, was developed as a backup to AIRS Version 5 should the AMSU-A instrument fail. Results are shown comparing the relative performance of the AIRS Version 4, Version 5, and Version 5 AO for the single day, January 25, 2003. The Goddard DISC is now generating and distributing products derived using the AIRS Science Team Version 5 retrieval algorithm. This paper also described the Quality Control flags contained in the DISC AIRS/AMSU retrieval products and their intended use for scientific research purposes.

  8. Major Upgrades to the AIRS Version-6 Water Vapor Profile Methodology

    Science.gov (United States)

    Susskind, Joel; Blaisdell, John; Iredell, Lena

    2015-01-01

    This research is a continuation of part of what was shown at the last AIRS Science Team Meeting and the AIRS 2015 NetMeeting. AIRS Version 6 was finalized in late 2012 and is now operational. Version 6 contained many significant improvements in retrieval methodology compared to Version 5. Version 6 retrieval methodology used for the water vapor profile q(p) and ozone profile O3(p) retrievals is basically unchanged from Version 5, or even from Version 4. Subsequent research has made significant improvements in both water vapor and O3 profiles compared to Version 6.

  9. Methodology for the energy analysis of compressed air systems; Metodologia para analisis energetico de sistemas de aire comprimido

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez, T; Ambriz, J J; Romero, H [Universidad Autonoma Metropolitana-Iztapalapa, Mexico, D. F. (Mexico)

    1993-12-31

    In this paper a methodology for the diagnosis of compressed air systems, for the identification of the potential energy saving is presented. The methodology consists in detecting the largest number of possible ways of energy saving. For this purpose it is divided into three parts: 1. Compressed air generation. 2. Compressed air distribution. 3. Compressed air users. For each one of the parts, the type of information required to perform the diagnosis study, as well as the necessary measuring equipment needed, is indicated. Afterwards, the possible saving ways that can be found and the ones that can be feasible, are analyzed. [Espanol] En este trabajo se presenta una metodologia para diagnosticar sistemas de aire comprimido, para identificar los potenciales de ahorro de energia. La metodologia consiste en detectar el mayor numero de posibles medidas de ahorro, para lo cual se divide en tres partes: 1. Generacion de aire comprimido. 2. Distribucion del aire comprimido. 3 Usuarios de aire comprimido. Para cada una de las partes se indica el tipo de informacion requerida para realizar el estudio de diagnostico, asi como el uso de equipo necesario de medicion. Despues se analizan las posibles medidas de ahorro que se pueden encontrar y las que pueden ser viables.

  10. Methodology for the energy analysis of compressed air systems; Metodologia para analisis energetico de sistemas de aire comprimido

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez, T.; Ambriz, J. J.; Romero, H. [Universidad Autonoma Metropolitana-Iztapalapa, Mexico, D. F. (Mexico)

    1992-12-31

    In this paper a methodology for the diagnosis of compressed air systems, for the identification of the potential energy saving is presented. The methodology consists in detecting the largest number of possible ways of energy saving. For this purpose it is divided into three parts: 1. Compressed air generation. 2. Compressed air distribution. 3. Compressed air users. For each one of the parts, the type of information required to perform the diagnosis study, as well as the necessary measuring equipment needed, is indicated. Afterwards, the possible saving ways that can be found and the ones that can be feasible, are analyzed. [Espanol] En este trabajo se presenta una metodologia para diagnosticar sistemas de aire comprimido, para identificar los potenciales de ahorro de energia. La metodologia consiste en detectar el mayor numero de posibles medidas de ahorro, para lo cual se divide en tres partes: 1. Generacion de aire comprimido. 2. Distribucion del aire comprimido. 3 Usuarios de aire comprimido. Para cada una de las partes se indica el tipo de informacion requerida para realizar el estudio de diagnostico, asi como el uso de equipo necesario de medicion. Despues se analizan las posibles medidas de ahorro que se pueden encontrar y las que pueden ser viables.

  11. Methodology for modeling the microbial contamination of air filters.

    Science.gov (United States)

    Joe, Yun Haeng; Yoon, Ki Young; Hwang, Jungho

    2014-01-01

    In this paper, we propose a theoretical model to simulate microbial growth on contaminated air filters and entrainment of bioaerosols from the filters to an indoor environment. Air filter filtration and antimicrobial efficiencies, and effects of dust particles on these efficiencies, were evaluated. The number of bioaerosols downstream of the filter could be characterized according to three phases: initial, transitional, and stationary. In the initial phase, the number was determined by filtration efficiency, the concentration of dust particles entering the filter, and the flow rate. During the transitional phase, the number of bioaerosols gradually increased up to the stationary phase, at which point no further increase was observed. The antimicrobial efficiency and flow rate were the dominant parameters affecting the number of bioaerosols downstream of the filter in the transitional and stationary phase, respectively. It was found that the nutrient fraction of dust particles entering the filter caused a significant change in the number of bioaerosols in both the transitional and stationary phases. The proposed model would be a solution for predicting the air filter life cycle in terms of microbiological activity by simulating the microbial contamination of the filter.

  12. Methodology for modeling the microbial contamination of air filters.

    Directory of Open Access Journals (Sweden)

    Yun Haeng Joe

    Full Text Available In this paper, we propose a theoretical model to simulate microbial growth on contaminated air filters and entrainment of bioaerosols from the filters to an indoor environment. Air filter filtration and antimicrobial efficiencies, and effects of dust particles on these efficiencies, were evaluated. The number of bioaerosols downstream of the filter could be characterized according to three phases: initial, transitional, and stationary. In the initial phase, the number was determined by filtration efficiency, the concentration of dust particles entering the filter, and the flow rate. During the transitional phase, the number of bioaerosols gradually increased up to the stationary phase, at which point no further increase was observed. The antimicrobial efficiency and flow rate were the dominant parameters affecting the number of bioaerosols downstream of the filter in the transitional and stationary phase, respectively. It was found that the nutrient fraction of dust particles entering the filter caused a significant change in the number of bioaerosols in both the transitional and stationary phases. The proposed model would be a solution for predicting the air filter life cycle in terms of microbiological activity by simulating the microbial contamination of the filter.

  13. Methodology for estimation of secondary meteorological variables to be used in local dispersion of air pollutants

    International Nuclear Information System (INIS)

    Turtos, L.; Sanchez, M.; Roque, A.; Soltura, R.

    2003-01-01

    Methodology for estimation of secondary meteorological variables to be used in local dispersion of air pollutants. This paper include the main works, carried out into the frame of the project Atmospheric environmental externalities of the electricity generation in Cuba, aiming to develop methodologies and corresponding software, which will allow to improve the quality of the secondary meteorological data used in atmospheric pollutant calculations; specifically the wind profiles coefficient, urban and rural mixed high and temperature gradients

  14. Mass casualty tracking with air traffic control methodologies.

    Science.gov (United States)

    Hoskins, Jason D; Graham, Ross F; Robinson, Duane R; Lutz, Clifford C; Folio, Les R

    2009-06-01

    An intrahospital casualty throughput system modeled after air traffic control (ATC) tracking procedures was tested in mass casualty exercises. ATC uses a simple tactile process involving informational progress strips representing each aircraft, which are held in bays representing each stage of flight to prioritize and manage aircraft. These strips can be reordered within the bays to indicate a change in priority of aircraft sequence. In this study, a similar system was designed for patient tracking. We compared the ATC model and traditional casualty tracking methods of paper and clipboard in 18 four-hour casualty scenarios, each with 5 to 30 mock casualties. The experimental and control groups were alternated to maximize exposure and minimize training effects. Results were analyzed with Mann-Whitney statistical analysis with p value < 0.05 (two-sided). The ATC method had significantly (p = 0.017) fewer errors in critical patient data (eg, name, social security number, diagnosis). Specifically, the ATC method better tracked the mechanism of injury, working diagnosis, and disposition of patients. The ATC method also performed considerably better with patient accountability during mass casualty scenarios. Data strips were comparable with the control method in terms of ease of use. In addition, participants preferred the ATC method to the control (p = 0.003) and preferred using the ATC method (p = 0.003) to traditional methods in the future. The ATC model more effectively tracked patient data with fewer errors when compared with the clipboard method. Application of these principles can enhance trauma management and can have application in civilian and military trauma centers and emergency rooms.

  15. Trimming and clustering sugarcane ESTs

    Directory of Open Access Journals (Sweden)

    Guilherme P. Telles

    2001-12-01

    Full Text Available The original clustering procedure adopted in the Sugarcane Expressed Sequence Tag project (SUCEST had many problems, for instance too many clusters, the presence of ribosomal sequences, etc. We therefore redesigned the clustering procedure entirely, including a much more careful initial trimming of the reads. In this paper the new trimming and clustering strategies are described in detail and we give the new official figures for the project, 237,954 expressed sequence tags and 43,141 clusters.O método de clustering adotado no Projeto SUCEST (Sugarcane EST Project tinha vários problemas (muitos clusters, presença de seqüências de ribossomo etc. Nós assumimos a tarefa de reprojetar todo o processo de clustering, propondo uma "limpeza" inicial mais cuidadosa das seqüências. Neste artigo as estratégias de limpeza das seqüências e de clustering são descritas em detalhe, incluindo os números oficiais do projeto (237,954 ESTs e 43,141 clusters.

  16. Methodology for Air Quality Forecast Downscaling from Regional- to Street-Scale

    Science.gov (United States)

    Baklanov, Alexander; Nuterman, Roman; Mahura, Alexander; Amstrup, Bjarne; Hansen Saas, Bent; Havskov Sørensen, Jens; Lorenzen, Thomas; Weismann, Jakob

    2010-05-01

    The most serious air pollution events occur in cities where there is a combination of high population density and air pollution, e.g. from vehicles. The pollutants can lead to serious human health problems, including asthma, irritation of the lungs, bronchitis, pneumonia, decreased resistance to respiratory infections, and premature death. In particular air pollution is associated with increase in cardiovascular disease and lung cancer. In 2000 WHO estimated that between 2.5 % and 11 % of total annual deaths are caused by exposure to air pollution. However, European-scale air quality models are not suited for local forecasts, as their grid-cell is typically of the order of 5 to 10km and they generally lack detailed representation of urban effects. Two suites are used in the framework of the EC FP7 project MACC (Monitoring of Atmosphere Composition and Climate) to demonstrate how downscaling from the European MACC ensemble to local-scale air quality forecast will be carried out: one will illustrate capabilities for the city of Copenhagen (Denmark); the second will focus on the city of Bucharest (Romania). This work is devoted to the first suite, where methodological aspects of downscaling from regional (European/ Denmark) to urban scale (Copenhagen), and from the urban down to street scale. The first results of downscaling according to the proposed methodology are presented. The potential for downscaling of European air quality forecasts by operating urban and street-level forecast models is evaluated. This will bring a strong support for continuous improvement of the regional forecast modelling systems for air quality in Europe, and underline clear perspectives for the future regional air quality core and downstream services for end-users. At the end of the MACC project, requirements on "how-to-do" downscaling of European air-quality forecasts to the city and street levels with different approaches will be formulated.

  17. Resistor trimming geometry; past, present and future

    International Nuclear Information System (INIS)

    Alafogianni, M; Penlington, R; Birkett, M

    2016-01-01

    This paper explores the key developments in thin film resistive trimming geometry for use in the fabrication of discrete precision resistors. Firstly an introduction to the laser trimming process is given with respect to well established trim geometries such as the plunge, 'L' and serpentine cuts. The effect of these trim patterns on key electrical properties of resistance tolerance and temperature co-efficient of resistance (TCR) of the thin films is then discussed before the performance of more recent geometries such as the three-contact and random trim approaches are reviewed. In addition to the properties of the standard trim patterns, the concept of the heat affected zone (HAZ) and ablation energy and the effect of introducing a 'fine' trim in areas of low current density to improve device performance are also studied. It is shown how trimming geometry and laser parameters can be systematically controlled to produce thin film resistors of the required properties for varying applications such as high precision, long term stability and high power pulse performance

  18. 14 CFR 23.677 - Trim systems.

    Science.gov (United States)

    2010-01-01

    ... to the pilot the position of the trim device with respect to both the range of adjustment and, in the... a position or range within which it has been demonstrated that take-off is safe for all center of gravity positions and each flap position approved for takeoff. (b) Trimming devices must be designed so...

  19. Origin and diversification of TRIM ubiquitin ligases.

    Directory of Open Access Journals (Sweden)

    Ignacio Marín

    Full Text Available Most proteins of the TRIM family (also known as RBCC family are ubiquitin ligases that share a peculiar protein structure, characterized by including an N-terminal RING finger domain closely followed by one or two B-boxes. Additional protein domains found at their C termini have been used to classify TRIM proteins into classes. TRIMs are involved in multiple cellular processes and many of them are essential components of the innate immunity system of animal species. In humans, it has been shown that mutations in several TRIM-encoding genes lead to diverse genetic diseases and contribute to several types of cancer. They had been hitherto detected only in animals. In this work, by comprehensively analyzing the available diversity of TRIM and TRIM-like protein sequences and evaluating their evolutionary patterns, an improved classification of the TRIM family is obtained. Members of one of the TRIM subfamilies defined, called Subfamily A, turn to be present not only in animals, but also in many other eukaryotes, such as fungi, apusozoans, alveolates, excavates and plants. The rest of subfamilies are animal-specific and several of them originated only recently. Subfamily A proteins are characterized by containing a MATH domain, suggesting a potential evolutionary connection between TRIM proteins and a different type of ubiquitin ligases, known as TRAFs, which contain quite similar MATH domains. These results indicate that the TRIM family emerged much earlier than so far thought and contribute to our understanding of its origin and diversification. The structural and evolutionary links with the TRAF family of ubiquitin ligases can be experimentally explored to determine whether functional connections also exist.

  20. A safety assessment methodology applied to CNS/ATM-based air traffic control system

    Energy Technology Data Exchange (ETDEWEB)

    Vismari, Lucio Flavio, E-mail: lucio.vismari@usp.b [Safety Analysis Group (GAS), School of Engineering at University of Sao Paulo (Poli-USP), Av. Prof. Luciano Gualberto, Trav.3, n.158, Predio da Engenharia de Eletricidade, Sala C2-32, CEP 05508-900, Sao Paulo (Brazil); Batista Camargo Junior, Joao, E-mail: joaocamargo@usp.b [Safety Analysis Group (GAS), School of Engineering at University of Sao Paulo (Poli-USP), Av. Prof. Luciano Gualberto, Trav.3, n.158, Predio da Engenharia de Eletricidade, Sala C2-32, CEP 05508-900, Sao Paulo (Brazil)

    2011-07-15

    In the last decades, the air traffic system has been changing to adapt itself to new social demands, mainly the safe growth of worldwide traffic capacity. Those changes are ruled by the Communication, Navigation, Surveillance/Air Traffic Management (CNS/ATM) paradigm , based on digital communication technologies (mainly satellites) as a way of improving communication, surveillance, navigation and air traffic management services. However, CNS/ATM poses new challenges and needs, mainly related to the safety assessment process. In face of these new challenges, and considering the main characteristics of the CNS/ATM, a methodology is proposed at this work by combining 'absolute' and 'relative' safety assessment methods adopted by the International Civil Aviation Organization (ICAO) in ICAO Doc.9689 , using Fluid Stochastic Petri Nets (FSPN) as the modeling formalism, and compares the safety metrics estimated from the simulation of both the proposed (in analysis) and the legacy system models. To demonstrate its usefulness, the proposed methodology was applied to the 'Automatic Dependent Surveillance-Broadcasting' (ADS-B) based air traffic control system. As conclusions, the proposed methodology assured to assess CNS/ATM system safety properties, in which FSPN formalism provides important modeling capabilities, and discrete event simulation allowing the estimation of the desired safety metric.

  1. A safety assessment methodology applied to CNS/ATM-based air traffic control system

    International Nuclear Information System (INIS)

    Vismari, Lucio Flavio; Batista Camargo Junior, Joao

    2011-01-01

    In the last decades, the air traffic system has been changing to adapt itself to new social demands, mainly the safe growth of worldwide traffic capacity. Those changes are ruled by the Communication, Navigation, Surveillance/Air Traffic Management (CNS/ATM) paradigm , based on digital communication technologies (mainly satellites) as a way of improving communication, surveillance, navigation and air traffic management services. However, CNS/ATM poses new challenges and needs, mainly related to the safety assessment process. In face of these new challenges, and considering the main characteristics of the CNS/ATM, a methodology is proposed at this work by combining 'absolute' and 'relative' safety assessment methods adopted by the International Civil Aviation Organization (ICAO) in ICAO Doc.9689 , using Fluid Stochastic Petri Nets (FSPN) as the modeling formalism, and compares the safety metrics estimated from the simulation of both the proposed (in analysis) and the legacy system models. To demonstrate its usefulness, the proposed methodology was applied to the 'Automatic Dependent Surveillance-Broadcasting' (ADS-B) based air traffic control system. As conclusions, the proposed methodology assured to assess CNS/ATM system safety properties, in which FSPN formalism provides important modeling capabilities, and discrete event simulation allowing the estimation of the desired safety metric.

  2. OPTIMIZATION OF MICROWAVE AND AIR DRYING CONDITIONS OF QUINCE (CYDONIA OBLONGA, MILLER USING RESPONSE SURFACE METHODOLOGY

    Directory of Open Access Journals (Sweden)

    Cem Baltacioglu

    2015-03-01

    Full Text Available Effects of slice thickness of quince (Cydonia oblonga Miller , microwave incident power and air drying temperature on antioxidant activity and total phenolic content of quince were investigated during drying in microwave and air drying. Optimum conditions were found to be: i for microwave drying, 285 W and 4.14 mm thick (maximum antioxidant activity and 285 W and 6.85 mm thick (maximum total phenolic content, and ii for air drying, 75 ºC and 1.2 mm thick (both maximum antioxidant activity and total phenolic content. Drying conditions were optimized by using the response surface methodology. 13 experiments were carried out considering incident microwave powers from 285 to 795 W, air temperature from 46 to 74 ºC and slice thickness from 1.2 to 6.8 mm.

  3. A proposed methodology for the assessment of arsenic, nickel, cadmium and lead levels in ambient air

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Germán, E-mail: santosg@unican.es; Fernández-Olmo, Ignacio

    2016-06-01

    Air quality assessment, required by the European Union (EU) Air Quality Directive, Directive 2008/50/EC, is part of the functions attributed to Environmental Management authorities. Based on the cost and time consumption associated with the experimental works required for the air quality assessment in relation to the EU-regulated metal and metalloids, other methods such as modelling or objective estimation arise as competitive alternatives when, in accordance with the Air Quality Directive, the levels of pollutants permit their use at a specific location. This work investigates the possibility of using statistical models based on Partial Least Squares Regression (PLSR) and Artificial Neural Networks (ANNs) to estimate the levels of arsenic (As), cadmium (Cd), nickel (Ni) and lead (Pb) in ambient air and their application for policy purposes. A methodology comprising the main steps that should be taken into consideration to prepare the input database, develop the model and evaluate their performance is proposed and applied to a case of study in Santander (Spain). It was observed that even though these approaches present some difficulties in estimating the individual sample concentrations, having an equivalent performance they can be considered valid for the estimation of the mean values – those to be compared with the limit/target values – fulfilling the uncertainty requirements in the context of the Air Quality Directive. Additionally, the influence of the consideration of input variables related to atmospheric stability on the performance of the studied statistical models has been determined. Although the consideration of these variables as additional inputs had no effect on As and Cd models, they did yield an improvement for Pb and Ni, especially with regard to ANN models. - Highlights: • EU encourages modelling techniques over measurements for air quality assessment. • A methodology for minor pollutants assessment by statistical modelling is presented.

  4. A proposed methodology for the assessment of arsenic, nickel, cadmium and lead levels in ambient air

    International Nuclear Information System (INIS)

    Santos, Germán; Fernández-Olmo, Ignacio

    2016-01-01

    Air quality assessment, required by the European Union (EU) Air Quality Directive, Directive 2008/50/EC, is part of the functions attributed to Environmental Management authorities. Based on the cost and time consumption associated with the experimental works required for the air quality assessment in relation to the EU-regulated metal and metalloids, other methods such as modelling or objective estimation arise as competitive alternatives when, in accordance with the Air Quality Directive, the levels of pollutants permit their use at a specific location. This work investigates the possibility of using statistical models based on Partial Least Squares Regression (PLSR) and Artificial Neural Networks (ANNs) to estimate the levels of arsenic (As), cadmium (Cd), nickel (Ni) and lead (Pb) in ambient air and their application for policy purposes. A methodology comprising the main steps that should be taken into consideration to prepare the input database, develop the model and evaluate their performance is proposed and applied to a case of study in Santander (Spain). It was observed that even though these approaches present some difficulties in estimating the individual sample concentrations, having an equivalent performance they can be considered valid for the estimation of the mean values – those to be compared with the limit/target values – fulfilling the uncertainty requirements in the context of the Air Quality Directive. Additionally, the influence of the consideration of input variables related to atmospheric stability on the performance of the studied statistical models has been determined. Although the consideration of these variables as additional inputs had no effect on As and Cd models, they did yield an improvement for Pb and Ni, especially with regard to ANN models. - Highlights: • EU encourages modelling techniques over measurements for air quality assessment. • A methodology for minor pollutants assessment by statistical modelling is presented.

  5. Resistive RAMs as analog trimming elements

    Science.gov (United States)

    Aziza, H.; Perez, A.; Portal, J. M.

    2018-04-01

    This work investigates the use of Resistive Random Access Memory (RRAM) as an analog trimming device. The analog storage feature of the RRAM cell is evaluated and the ability of the RRAM to hold several resistance states is exploited to propose analog trim elements. To modulate the memory cell resistance, a series of short programming pulses are applied across the RRAM cell allowing a fine calibration of the RRAM resistance. The RRAM non volatility feature makes the analog device powers up already calibrated for the system in which the analog trimmed structure is embedded. To validate the concept, a test structure consisting of a voltage reference is evaluated.

  6. Environmental monitoring (water, soil, air, food) and some methodological aspects of radioactive decontamination

    International Nuclear Information System (INIS)

    Balanel, Vasile; Boldescu, Victoria; Mesina, Victor

    2013-01-01

    This paper presents research results of radiological samples taken from various media (water, soil, air and some food). The study showed that concentrations of radionuclides Cs 137 and Sr 90 did not exceed the maximum permissible. A high level of radionuclides but within the norm occurred in some imported food. The research describes methodology used in radioactive decontamination in practice of the modern world. (authors)

  7. Propulsion integration of hypersonic air-breathing vehicles utilizing a top-down design methodology

    Science.gov (United States)

    Kirkpatrick, Brad Kenneth

    In recent years, a focus of aerospace engineering design has been the development of advanced design methodologies and frameworks to account for increasingly complex and integrated vehicles. Techniques such as parametric modeling, global vehicle analyses, and interdisciplinary data sharing have been employed in an attempt to improve the design process. The purpose of this study is to introduce a new approach to integrated vehicle design known as the top-down design methodology. In the top-down design methodology, the main idea is to relate design changes on the vehicle system and sub-system level to a set of over-arching performance and customer requirements. Rather than focusing on the performance of an individual system, the system is analyzed in terms of the net effect it has on the overall vehicle and other vehicle systems. This detailed level of analysis can only be accomplished through the use of high fidelity computational tools such as Computational Fluid Dynamics (CFD) or Finite Element Analysis (FEA). The utility of the top-down design methodology is investigated through its application to the conceptual and preliminary design of a long-range hypersonic air-breathing vehicle for a hypothetical next generation hypersonic vehicle (NHRV) program. System-level design is demonstrated through the development of the nozzle section of the propulsion system. From this demonstration of the methodology, conclusions are made about the benefits, drawbacks, and cost of using the methodology.

  8. Peak-Seeking Control for Trim Optimization

    Data.gov (United States)

    National Aeronautics and Space Administration — Innovators have developed a peak-seeking algorithm that can reduce drag and improve performance and fuel efficiency by optimizing aircraft trim in real time. The...

  9. Trim waste minimization at the Pinellas Plant

    International Nuclear Information System (INIS)

    DeLaneuville, D.

    1992-01-01

    Bacteria counts and several methods of slowing bacterial growth in machine trim coolant are suggested to reduce the frequency of coolant replacement without risking employee health or the longevity of the product or machinery. On-site treatment and disposal of waste trim are recommended to further reduce waste volume. This paper discusses the benefits of these efforts, including projected cost savings based on partial implementation at the Department of Energy's Pinellas Plant

  10. Airplane automatic control force trimming device for asymmetric engine failures

    Science.gov (United States)

    Stewart, Eric C. (Inventor)

    1987-01-01

    The difference in dynamic pressure in the propeller slipstreams as measured by sensors is divided by the freestream dynamic pressure generating a quantity proportional to the differential thrust coefficient. This quantity is used to command an electric trim motor to change the position of trim tab thereby retrimming the airplane to the new asymmetric power condition. The change in position of the trim tab produced by the electric trim motor is summed with the pilot's input to produce the actual trim tab position.

  11. Case-Crossover Analysis of Air Pollution Health Effects: A Systematic Review of Methodology and Application

    Science.gov (United States)

    Carracedo-Martínez, Eduardo; Taracido, Margarita; Tobias, Aurelio; Saez, Marc; Figueiras, Adolfo

    2010-01-01

    Background Case-crossover is one of the most used designs for analyzing the health-related effects of air pollution. Nevertheless, no one has reviewed its application and methodology in this context. Objective We conducted a systematic review of case-crossover (CCO) designs used to study the relationship between air pollution and morbidity and mortality, from the standpoint of methodology and application. Data sources and extraction A search was made of the MEDLINE and EMBASE databases. Reports were classified as methodologic or applied. From the latter, the following information was extracted: author, study location, year, type of population (general or patients), dependent variable(s), independent variable(s), type of CCO design, and whether effect modification was analyzed for variables at the individual level. Data synthesis The review covered 105 reports that fulfilled the inclusion criteria. Of these, 24 addressed methodological aspects, and the remainder involved the design’s application. In the methodological reports, the designs that yielded the best results in simulation were symmetric bidirectional CCO and time-stratified CCO. Furthermore, we observed an increase across time in the use of certain CCO designs, mainly symmetric bidirectional and time-stratified CCO. The dependent variables most frequently analyzed were those relating to hospital morbidity; the pollutants most often studied were those linked to particulate matter. Among the CCO-application reports, 13.6% studied effect modification for variables at the individual level. Conclusions The use of CCO designs has undergone considerable growth; the most widely used designs were those that yielded better results in simulation studies: symmetric bidirectional and time-stratified CCO. However, the advantages of CCO as a method of analysis of variables at the individual level are put to little use. PMID:20356818

  12. Air and radon pathways screenings methodologies for the next revision of the E-area PA

    Energy Technology Data Exchange (ETDEWEB)

    Dyer, J. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-10-31

    The strategic plan for the next E-Area Low-Level Waste Facility Performance Assessment includes recommended changes to the screening criteria used to reduce the number of radioisotopes that are to be considered in the air and radon pathways incorporated into the GoldSim® atmospheric release model (ARM). For the air pathway, a revised screening methodology was developed based on refinement of previous E-Area PA screening approaches and consideration of the strategic plan recommendations. The revised methodology has three sequential screening steps for each radioisotope: (1) volatility test using the Periodic Table of the Elements, (2) stability test based on half-life, and (3) stability test based on volatility as measured by the Henry’s Law constant for the assumed dominant gaseous species or vapor pressure in the case of tritiated water. Of the 1252 radioisotopes listed in the International Commission on Radiological Protection Publication 107, only the 10 that satisfied all three steps of the revised screening methodology will be included in the ARM. They are: Ar-37, Ar-39, Ar-42, C-14, H-3, Hg-194, Hg-203, Kr-81, Kr-85, and Xe-127. For the radon pathway, a revised screening methodology was developed that also has three sequential steps: (1) identify all decay chains that terminate at Rn-222, (2) screen out parents that decay through U-238 because of its 4.5-billion-year primordial half-life, and (3) eliminate remaining parents whose half-life is shorter than one day. Of the 86 possible decay chains leading to Rn-222, six decay chains consist of 15 unique radioisotopes that will be incorporated into the ARM. The 15 radioisotopes are: U-238, Th-234, Pa-234m, Pu-238, U-234, Th-230, Ra-226, Cf-246, Cm-242, Am-242m, Am-242, Np-238, Np-234, Pa-230, and Rn-222.

  13. A Methodology of Health Effects Estimation from Air Pollution in Large Asian Cities

    Directory of Open Access Journals (Sweden)

    Keiko Hirota

    2017-09-01

    Full Text Available The increase of health effects caused by air pollution seems to be a growing concern in Asian cities with increasing motorization. This paper discusses methods of estimating the health effects of air pollution in large Asian cities. Due to the absence of statistical data in Asia, this paper carefully chooses the methodology using data of the Japanese compensation system. A basic idea of health effects will be captured from simple indicators, such as population and air quality, in a correlation model. This correlation model enables more estimation results of respiratory mortality caused by air pollution to be yielded than by using the relative model. The correlation model could be an alternative method to estimate mortality besides the relative risk model since the results of the correlation model are comparable with those of the relative model by city and by time series. The classification of respiratory diseases is not known from the statistical yearbooks in many countries. Estimation results could support policy decision-making with respect to public health in a cost-effective way.

  14. Results from CrIS-ATMS Obtained Using the AIRS Science Team Retrieval Methodology

    Science.gov (United States)

    Susskind, Joel; Kouvaris, Louis C.; Iredell, Lena

    2013-01-01

    AIRS was launched on EOS Aqua in May 2002, together with AMSU-A and HSB (which subsequently failed early in the mission), to form a next generation polar orbiting infrared and microwave atmospheric sounding system. AIRS/AMSU had two primary objectives. The first objective was to provide real-time data products available for use by the operational Numerical Weather Prediction Centers in a data assimilation mode to improve the skill of their subsequent forecasts. The second objective was to provide accurate unbiased sounding products with good spatial coverage that are used to generate stable multi-year climate data sets to study the earth's interannual variability, climate processes, and possibly long-term trends. AIRS/AMSU data for all time periods are now being processed using the state of the art AIRS Science Team Version-6 retrieval methodology. The Suomi-NPP mission was launched in October 2011 as part of a sequence of Low Earth Orbiting satellite missions under the "Joint Polar Satellite System" (JPSS). NPP carries CrIS and ATMS, which are advanced infra-red and microwave atmospheric sounders that were designed as follow-ons to the AIRS and AMSU instruments. The main objective of this work is to assess whether CrIS/ATMS will be an adequate replacement for AIRS/AMSU from the perspective of the generation of accurate and consistent long term climate data records, or if improved instruments should be developed for future flight. It is critical for CrIS/ATMS to be processed using an algorithm similar to, or at least comparable to, AIRS Version-6 before such an assessment can be made. We have been conducting research to optimize products derived from CrIS/ATMS observations using a scientific approach analogous to the AIRS Version-6 retrieval algorithm. Our latest research uses Version-5.70 of the CrIS/ATMS retrieval algorithm, which is otherwise analogous to AIRS Version-6, but does not yet contain the benefit of use of a Neural-Net first guess start-up system

  15. Trim cut machining and surface integrity analysis of Nimonic 80A alloy using wire cut EDM

    Directory of Open Access Journals (Sweden)

    Amitesh Goswami

    2017-02-01

    Full Text Available This present work deals with the features of trim cut wire EDM machining of Nimonic 80A in terms of machining parameters, to predict material removal rate (MRR, surface roughness (Ra, wire wear ratio (WWR and microstructure analysis. Trim cut is performed after rough cut to remove the rough layer deposited after machining due to melting and re-solidification of the eroded metal from workpiece as well as from wire electrode. Taguchi’s design of experiments methodology has been used for planning and designing the experiments. The relative significance of various factors has also been evaluated and analyzed using ANOVA. The results clearly indicate trim cut potential for high surface finish compared to rough cut machining.

  16. Comparison of the DOE and the EPA risk assessment methodologies and default parameters for the air exposure pathway

    International Nuclear Information System (INIS)

    Tan, Z.; Eckart, R.

    1993-01-01

    The U.S. Department of Energy (DOE) and the U.S. Environmental Protection Agency (EPA) each publish radiological health effects risk assessment methodologies. Those methodologies are in the form of computer program models or extensive documentation. This research paper compares the significant differences between the DOE and EPA methodologies and default parameters for the important air exposure pathway. The purpose of this analysis was to determine the fundamental differences in methodology and parameter values between the DOE and the EPA. This study reviewed the parameter values and default values that are utilized in the air exposure pathway and revealed the significant differences in risk assessment results when default values are used in the analysis of an actual site. The study details the sources and the magnitude of the parameter departures between the DOE and the EPA methodologies and their impact on dose or risk

  17. A novel methodology for interpreting air quality measurements from urban streets using CFD modelling

    Science.gov (United States)

    Solazzo, Efisio; Vardoulakis, Sotiris; Cai, Xiaoming

    2011-09-01

    In this study, a novel computational fluid dynamics (CFD) based methodology has been developed to interpret long-term averaged measurements of pollutant concentrations collected at roadside locations. The methodology is applied to the analysis of pollutant dispersion in Stratford Road (SR), a busy street canyon in Birmingham (UK), where a one-year sampling campaign was carried out between August 2005 and July 2006. Firstly, a number of dispersion scenarios are defined by combining sets of synoptic wind velocity and direction. Assuming neutral atmospheric stability, CFD simulations are conducted for all the scenarios, by applying the standard k-ɛ turbulence model, with the aim of creating a database of normalised pollutant concentrations at specific locations within the street. Modelled concentration for all wind scenarios were compared with hourly observed NO x data. In order to compare with long-term averaged measurements, a weighted average of the CFD-calculated concentration fields was derived, with the weighting coefficients being proportional to the frequency of each scenario observed during the examined period (either monthly or annually). In summary the methodology consists of (i) identifying the main dispersion scenarios for the street based on wind speed and directions data, (ii) creating a database of CFD-calculated concentration fields for the identified dispersion scenarios, and (iii) combining the CFD results based on the frequency of occurrence of each dispersion scenario during the examined period. The methodology has been applied to calculate monthly and annually averaged benzene concentration at several locations within the street canyon so that a direct comparison with observations could be made. The results of this study indicate that, within the simplifying assumption of non-buoyant flow, CFD modelling can aid understanding of long-term air quality measurements, and help assessing the representativeness of monitoring locations for population

  18. Non-local means filter for trim statics

    KAUST Repository

    Huang, Yunsong; Wang, Xin; Schuster, Gerard T.

    2014-01-01

    this problem, we propose a trim statics inspired by the non-local means algorithm originally developed for image denoising. This method differs from the conventional one in two fundamental respects. First, the trim statics are computed by comparing image

  19. TRIM65 negatively regulates p53 through ubiquitination

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yang [Department of Respiration, The First Hospital of Jilin University, Changchun 130021 (China); Ma, Chengyuan [Department of Neurosurgery, The First Hospital of Jilin University, Changchun 130021 (China); Zhou, Tong [Department of Endocrinology, The First Hospital of Jilin University, Changchun 130021 (China); Liu, Ying [Department of Respiration, The First Hospital of Jilin University, Changchun 130021 (China); Sun, Luyao [Department of Infectious Diseases, The First Hospital of Jilin University, Changchun 130021 (China); Yu, Zhenxiang, E-mail: zhenxiangyu2015@gmail.com [Department of Respiration, The First Hospital of Jilin University, Changchun 130021 (China)

    2016-04-22

    Tripartite-motif protein family member 65 (TRIM65) is an important protein involved in white matter lesion. However, the role of TRIM65 in human cancer remains less understood. Through the Cancer Genome Atlas (TCGA) gene alteration database, we found that TRIM65 is upregulated in a significant portion of non-small cell lung carcinoma (NSCLC) patients. Our cell growth assay revealed that TRIM65 overexpression promotes cell proliferation, while knockdown of TRIM65 displays opposite effect. Mechanistically, TRIM65 binds to p53, one of the most critical tumor suppressors, and serves as an E3 ligase toward p53. Consequently, TRIM65 inactivates p53 through facilitating p53 poly-ubiquitination and proteasome-mediated degradation. Notably, chemotherapeutic reagent cisplatin induction of p53 is markedly attenuated in response to ectopic expression of TRIM65. Cell growth inhibition by TRIM65 knockdown is more significant in p53 positive H460 than p53 negative H1299 cells, and knockdown of p53 in H460 cells also shows compromised cell growth inhibition by TRIM65 knockdown, indicating that p53 is required, at least in part, for TRIM65 function. Our findings demonstrate TRIM65 as a potential oncogenic protein, highly likely through p53 inactivation, and provide insight into development of novel approaches targeting TRIM65 for NSCLC treatment, and also overcoming chemotherapy resistance. - Highlights: • TRIM65 expression is elevated in NSCLC. • TRIM65 inactivates p53 through mediating p53 ubiquitination and degradation. • TRIM65 attenuates the response of NSCLC cells to cisplatin.

  20. Automatic Edging and Trimming of Hardwood Lumber

    Science.gov (United States)

    D. Earl Kline; Eugene M. Wengert; Philip A. Araman

    1990-01-01

    Studies have shown that there is a potential to increase hardwood lumber value by more than 20 percent through optimum edging and trimming. Even a small portion of this percentage can boost the profitability of hardwood lumber manufacturers substantially. The objective of this research project is to develop an automated system which would assist in correct edging and...

  1. 14 CFR 25.255 - Out-of-trim characteristics.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Out-of-trim characteristics. 25.255 Section 25.255 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT...-trim characteristics. (a) From an initial condition with the airplane trimmed at cruise speeds up to...

  2. Development of residential-conservation-survey methodology for the US Air Force. Interim report. Task two

    Energy Technology Data Exchange (ETDEWEB)

    Abrams, D. W.; Hartman, T. L.; Lau, A. S.

    1981-11-13

    A US Air Force (USAF) Residential Energy Conservation Methodology was developed to compare USAF needs and available data to the procedures of the Residential Conservation Service (RCS) program as developed for general use by utility companies serving civilian customers. Attention was given to the data implications related to group housing, climatic data requirements, life-cycle cost analysis, energy saving modifications beyond those covered by RCS, and methods for utilizing existing energy consumption data in approaching the USAF survey program. Detailed information and summaries are given on the five subtasks of the program. Energy conservation alternatives are listed and the basic analysis techniques to be used in evaluating their thermal performane are described. (MCW)

  3. Calculating emissions into the air. General methodological principles; Calcul des emissions dans l'air. Principes methodologiques generaux

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Knowing the quantities of certain substances discharged into the atmosphere is a necessary and fundamental stage in any environmental protection policy to tackle today's problems such as acid rain, the degradation of air quality, global warming and climate change, the depletion of the ozone layer, etc. This quantification, usually known as an 'emission inventory', is built on a set of specific rules which may vary from one inventory to another. This state of affairs presents the enormous disadvantage that the data available are not comparable. At the international level, an attempt at harmonization has been going on for some years between the various international bodies. This work is being pursued in parallel with the improvement of methodologies to estimate discharges from various types of source. To take account of changes in specifications and of improvements in our understanding of phenomena giving rise to atmospheric pollution, the results of inventories of emissions need to be regularly revised, even retrospectively, to maintain a consistent series. CITEPA, which acts as a National Reference Centre, has developed a system of inventories as part of the CORALIE programme with financial help from the French Ministry for Planning and the Environment. (author)

  4. Calculating emissions into the air. General methodological principles; Calcul des emissions dans l'air. Principes methodologiques generaux

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Knowing the quantities of certain substances discharged into the atmosphere is a necessary and fundamental stage in any environmental protection policy to tackle today's problems such as acid rain, the degradation of air quality, global warming and climate change, the depletion of the ozone layer, etc. This quantification, usually known as an 'emission inventory', is built on a set of specific rules which may vary from one inventory to another. This state of affairs presents the enormous disadvantage that the data available are not comparable. At the international level, an attempt at harmonization has been going on for some years between the various international bodies. This work is being pursued in parallel with the improvement of methodologies to estimate discharges from various types of source. To take account of changes in specifications and of improvements in our understanding of phenomena giving rise to atmospheric pollution, the results of inventories of emissions need to be regularly revised, even retrospectively, to maintain a consistent series. CITEPA, which acts as a National Reference Centre, has developed a system of inventories as part of the CORALIE programme with financial help from the French Ministry for Planning and the Environment. (author)

  5. A brief history of TRIM5alpha.

    Science.gov (United States)

    Newman, Ruchi M; Johnson, Welkin E

    2007-01-01

    In spite of the fact that the first isolates of HIV-1 became available more than 20 years ago, there is still no robust animal model for HIV-1 replication and pathogenesis. This is largely due to the existence of multiple genetic barriers to HIV-1 replication in most nonhuman primates, including a severe block targeting the early, post-entry phase of the viral replication cycle. It is now known that a protein called TRIM5alpha mediates this early restriction in nonhuman primate cells. Tissue culture experiments, together with genetic association studies involving multiple HIV/AIDS cohorts, indicate that the human orthologue of TRIM5alpha does not have a significant impact on HIV-1 replication. However, most human alleles encode a functional protein that can restrict at least one retrovirus unrelated to HIV-1 (N-tropic murine leukemia virus), although one deleterious mutation (H43Y) is present at high frequency in human populations. Phylogenetic analyses of the TRIM5 locus reveal that prehistoric retroviral epidemics, not unlike the current HIV/AIDS pandemic, played a significant role in the evolutionary history of humans and their primate relatives. The discovery of TRIM5alpha's antiretroviral activity sparked the imaginations of many laboratories, and considerable effort has now been channeled into characterizing the protein and determining its possible mechanism(s) of action. It is hoped that research on TRIM5alpha will contribute to the establishment of new and improved models for HIV replication and AIDS pathogenesis, point the way towards novel therapeutic targets to stem the tide of the human AIDS epidemic, provide an experimental window onto the early, post-entry stages of the retroviral replication cycle, and even inspire the search for other cellular factors that modulate retroviral infection.

  6. A Life-Cycle Cost Estimating Methodology for NASA-Developed Air Traffic Control Decision Support Tools

    Science.gov (United States)

    Wang, Jianzhong Jay; Datta, Koushik; Landis, Michael R. (Technical Monitor)

    2002-01-01

    This paper describes the development of a life-cycle cost (LCC) estimating methodology for air traffic control Decision Support Tools (DSTs) under development by the National Aeronautics and Space Administration (NASA), using a combination of parametric, analogy, and expert opinion methods. There is no one standard methodology and technique that is used by NASA or by the Federal Aviation Administration (FAA) for LCC estimation of prospective Decision Support Tools. Some of the frequently used methodologies include bottom-up, analogy, top-down, parametric, expert judgement, and Parkinson's Law. The developed LCC estimating methodology can be visualized as a three-dimensional matrix where the three axes represent coverage, estimation, and timing. This paper focuses on the three characteristics of this methodology that correspond to the three axes.

  7. Epoxy resin casting of trim coils for superconducting cyclotron

    International Nuclear Information System (INIS)

    Hajra, D.P.; Sarkar, S.C.; Saha, Subimal; Chaudhuri, J.; Bhandari, R.K.

    2006-01-01

    The life of any magnet depends on the soundness of the coil insulation, its aging properties and initial and final endurance limitations. The insulation of water-cooled trim coils for superconducting cyclotron is made of glass fibre tape with heat cured unfilled epoxy resin combination. This type of insulation has been selected to achieve excellent stability against thermal and electromagnetic stresses, tight dimensional control, good dielectric strength, non-hygroscopic and considerably low vapour-pressure as it will be inside rough vacuum. The process development and the difficulties encountered for appropriate selection of epoxy resin combination, potting, vacuum process, curing cycle, control of coil dimension to achieve a sound coil absolutely free from cracks, trapped air and voids has been discussed. (author)

  8. Methodological and Ethical Dilemmas Encountered during Field Research of Family Violence Experienced by Adolescent Women in Buenos Aires

    Science.gov (United States)

    Luxardo, Natalia; Colombo, Graciela; Iglesias, Gabriela

    2011-01-01

    The purpose of this article is to examine some obstacles and dilemmas related to methodological strategies and ethical considerations that arose during the fieldwork of research focused on family violence during the stages of pregnancy and childbirth in adolescent females in Buenos Aires during 2007. From this study, we are able to contribute some…

  9. Welfare Consequences of Omitting Beak Trimming in Barn Layers

    DEFF Research Database (Denmark)

    Riber, Anja Brinch; Hinrichsen, Lena Karina

    2017-01-01

    Beak trimming is used worldwide as a method of reducing the damage to feathers and skin caused by injurious pecking in laying hens. However, beak trimming also causes some welfare issues as trimming the beak results in pain and sensory loss. Due to this dilemma, there is an ongoing discussion...... in several European countries about whether to ban beak trimming. In this study, we investigated the welfare consequences of keeping layers with intact beaks and examined for links between injurious pecking damage and keel bone damage on an individual level. A study was conducted on 10 commercial farms...... housing laying hens in the barn system. Each farm participated with a flock of beak-trimmed hens (T) and a flock of non-trimmed (NT) hens that were visited around 32 and 62 weeks of age. During visits, the condition of plumage, skin, feet, and keel bone of 100 hens was assessed. Mortality was recorded...

  10. Measuring core inflation in India: An asymmetric trimmed mean approach

    Directory of Open Access Journals (Sweden)

    Naresh Kumar Sharma

    2015-12-01

    Full Text Available The paper seeks to obtain an optimal asymmetric trimmed mean-based core inflation measure in the class of trimmed mean measures when the distribution of price changes is leptokurtic and skewed to the right for any given period. Several estimators based on asymmetric trimmed mean approach are constructed and estimates generated by use of these estimators are evaluated on the basis of certain established empirical criteria. The paper also provides the method of trimmed mean expression “in terms of percentile score.” This study uses 69 monthly price indices which are constituent components of Wholesale Price Index for the period, April 1994 to April 2009, with 1993–1994 as the base year. Results of the study indicate that an optimally trimmed estimator is found when we trim 29.5% from the left-hand tail and 20.5% from the right-hand tail of the distribution of price changes.

  11. Can citizen science produce good science? Testing the OPAL Air Survey methodology, using lichens as indicators of nitrogenous pollution

    International Nuclear Information System (INIS)

    Tregidgo, Daniel J.; West, Sarah E.; Ashmore, Mike R.

    2013-01-01

    Citizen science is having increasing influence on environmental monitoring as its advantages are becoming recognised. However methodologies are often simplified to make them accessible to citizen scientists. We tested whether a recent citizen science survey (the OPAL Air Survey) could detect trends in lichen community composition over transects away from roads. We hypothesised that the abundance of nitrophilic lichens would decrease with distance from the road, while that of nitrophobic lichens would increase. The hypothesised changes were detected along strong pollution gradients, but not where the road source was relatively weak, or background pollution relatively high. We conclude that the simplified OPAL methodology can detect large contrasts in nitrogenous pollution, but it may not be able to detect more subtle changes in pollution exposure. Similar studies are needed in conjunction with the ever-growing body of citizen science work to ensure that the limitations of these methods are fully understood. -- Highlights: •We investigated the validity of a simplified citizen science methodology. •Lichen abundance data were used to indicate nitrogenous air pollution. •Significant changes were detected beside busy roads with low background pollution. •The methodology detected major, but not subtle, contrasts in pollution. •Sensitivity of citizen science methods to environmental change must be evaluated. -- A simplified lichen biomonitoring method used for citizen science can detect the impact of nitrogenous air pollution from local roads

  12. Developing a source-receptor methodology for the characterization of VOC sources in ambient air

    International Nuclear Information System (INIS)

    Borbon, A.; Badol, C.; Locoge, N.

    2005-01-01

    Since 2001, in France, a continuous monitoring of about thirty ozone precursor non-methane hydrocarbons (NMHC) is led in some urban areas. The automated system for NMHC monitoring consists of sub-ambient preconcentration on a cooled multi-sorbent trap followed by thermal desorption and bidimensional Gas Chromatography/Flame Ionisation Detection analysis.The great number of data collected and their exploitation should provide a qualitative and quantitative assessment of hydrocarbon sources. This should help in the definition of relevant strategies of emission regulation as stated by the European Directive relative to ozone in ambient air (2002/3/EC). The purpose of this work is to present the bases and the contributions of an original methodology known as source-receptor in the characterization of NMHC sources. It is a statistical and diagnostic approach, adaptable and transposable in all urban sites, which integrates the spatial and temporal dynamics of the emissions. The methods for source identification combine descriptive or more complex complementary approaches: 1) univariate approach through the analysis of NMHC time series and concentration roses, 2) bivariate approach through a Graphical Ratio Analysis and a characterization of scatterplot distributions of hydrocarbon pairs, 3) multivariate approach with Principal Component Analyses on various time basis. A linear regression model is finally developed to estimate the spatial and temporal source contributions. Apart from vehicle exhaust emissions, sources of interest are: combustion and fossil fuel-related activities, petrol and/or solvent evaporation, the double anthropogenic and biogenic origin of isoprene and other industrial activities depending on local parameters. (author)

  13. Supporting the Future Total Force: A Methodology for Evaluating Potential Air National Guard Mission Assignments

    National Research Council Canada - National Science Library

    Lynch, Kristin F; Drew, John G; Sleeper, Sally; Williams, William A; Masters, James M; Luangkesorn, Louis; Tripp, Robert S; Lichter, Dahlia S; Roll, Charles R

    2007-01-01

    Manpower end-strength reductions of active duty personnel in the U.S. Air Force are making it more difficult to support the air and space expeditionary force construct using current force employment practices...

  14. Stable isogeometric analysis of trimmed geometries

    Science.gov (United States)

    Marussig, Benjamin; Zechner, Jürgen; Beer, Gernot; Fries, Thomas-Peter

    2017-04-01

    We explore extended B-splines as a stable basis for isogeometric analysis with trimmed parameter spaces. The stabilization is accomplished by an appropriate substitution of B-splines that may lead to ill-conditioned system matrices. The construction for non-uniform knot vectors is presented. The properties of extended B-splines are examined in the context of interpolation, potential, and linear elasticity problems and excellent results are attained. The analysis is performed by an isogeometric boundary element formulation using collocation. It is argued that extended B-splines provide a flexible and simple stabilization scheme which ideally suits the isogeometric paradigm.

  15. Internal trim coils for CBA superconducting magnets

    International Nuclear Information System (INIS)

    Thompson, P.A.; Aronson, S.; Cottingham, J.G.; Garber, M.; Hahn, H.; Sampson, W.B.

    1983-01-01

    In order to correct iron saturation effects and shape the beam working line, superconducting trim coils have been constructed, which operate inside the main coils. Detailed studies of mechanical properties, quench behavior, fields produced, and hysteresis have lead to the production of accelerator-quality coils generating the required-strength harmonics up to cos (7theta). These are routinely installed in CBA main magnets and operate at 80% of short sample with negligible training in an ambient field of more than 5.3T

  16. TRIM45, a novel human RBCC/TRIM protein, inhibits transcriptional activities of ElK-1 and AP-1

    International Nuclear Information System (INIS)

    Wang Yuequn; Li Yongqing; Qi Xinzhu; Yuan Wuzhou; Ai Jianping; Zhu Chuanbing; Cao Lei; Yang Hong; Liu Fang; Wu Xiushan; Liu Mingyao

    2004-01-01

    The tripartite motif (TRIM) proteins play important roles in a variety of cellular functions including cell proliferation, differentiation, development, oncogenesis, and apoptosis. In this study, we report the identification and characterization of the human tripartite motif-containing protein 45 (TRIM45), a novel member of the TRIM family, from a human embryonic heart cDNA library. TRIM45 has a predicted 580 amino acid open reading frame, encoding a putative 64-kDa protein. The N-terminal region harbors a RING finger, two B-boxes, and a predicted α-helical coiled-coil domain, which together form the RBCC/TRIM motif found in a large family of proteins, whereas the C-terminal region contains a filamin-type immunoglobulin (IG-FLMN) domain. Northern blot analysis indicates that TRIM45 is expressed in a variety of human adult and embryonic tissues. In the cell, TRIM45 protein is expressed both in cytoplasm and in cell nucleus. Overexpression of TRIM45 in COS-7 cells inhibits the transcriptional activities of ElK-1 and AP-1. These results suggest that TRIM45 may act as a new transcriptional repressor in mitogen-activated protein kinase signaling pathway

  17. Quantifying the health impacts of air pollution under a changing climate-a review of approaches and methodology.

    Science.gov (United States)

    Sujaritpong, Sarunya; Dear, Keith; Cope, Martin; Walsh, Sean; Kjellstrom, Tord

    2014-03-01

    Climate change has been predicted to affect future air quality, with inevitable consequences for health. Quantifying the health effects of air pollution under a changing climate is crucial to provide evidence for actions to safeguard future populations. In this paper, we review published methods for quantifying health impacts to identify optimal approaches and ways in which existing challenges facing this line of research can be addressed. Most studies have employed a simplified methodology, while only a few have reported sensitivity analyses to assess sources of uncertainty. The limited investigations that do exist suggest that examining the health risk estimates should particularly take into account the uncertainty associated with future air pollution emissions scenarios, concentration-response functions, and future population growth and age structures. Knowledge gaps identified for future research include future health impacts from extreme air pollution events, interactions between temperature and air pollution effects on public health under a changing climate, and how population adaptation and behavioural changes in a warmer climate may modify exposure to air pollution and health consequences.

  18. MATLAB Stability and Control Toolbox Trim and Static Stability Module

    Science.gov (United States)

    Kenny, Sean P.; Crespo, Luis

    2012-01-01

    MATLAB Stability and Control Toolbox (MASCOT) utilizes geometric, aerodynamic, and inertial inputs to calculate air vehicle stability in a variety of critical flight conditions. The code is based on fundamental, non-linear equations of motion and is able to translate results into a qualitative, graphical scale useful to the non-expert. MASCOT was created to provide the conceptual aircraft designer accurate predictions of air vehicle stability and control characteristics. The code takes as input mass property data in the form of an inertia tensor, aerodynamic loading data, and propulsion (i.e. thrust) loading data. Using fundamental nonlinear equations of motion, MASCOT then calculates vehicle trim and static stability data for the desired flight condition(s). Available flight conditions include six horizontal and six landing rotation conditions with varying options for engine out, crosswind, and sideslip, plus three take-off rotation conditions. Results are displayed through a unique graphical interface developed to provide the non-stability and control expert conceptual design engineer a qualitative scale indicating whether the vehicle has acceptable, marginal, or unacceptable static stability characteristics. If desired, the user can also examine the detailed, quantitative results.

  19. Performance of trim coils made by a novel method

    International Nuclear Information System (INIS)

    Wanderer, P.; Anerella, M.; Cottingham, J.; Ganetis, G.; Garber, M.; Ghosh, A.; Goodzeit, C.; Greene, A.; Gupta, R.; Herrera, J.; Kahn, S.; Kelly, E.; Meade, A.; Morgan, G.; Muratore, J.; Prodell, A.; Rehak, M.; Rohrer, E.P.; Sampson, W.; Shutt, R.; Skaritka, J.; Thompson, P.; Willen, E.

    1991-01-01

    A precision, automated method of manufacturing trim coils based on printed circuit technology has been developed. Excellent quench performance and increased radiation resistance have been achieved in recently-tested models of sextupole trim coils developed for operation inside 40 mm-aperture SSC Main Collider dipoles. 6 refs., 2 figs

  20. Surveillance for Intracellular Antibody by Cytosolic Fc Receptor TRIM21

    Directory of Open Access Journals (Sweden)

    William A. McEwan

    2016-11-01

    Full Text Available TRIM21 has emerged as an atypical Fc receptor that is broadly conserved and widely expressed in the cytoplasm of mammalian cells. Viruses that traffic surface-bound antibodies into the cell during infection recruit TRIM21 via a high affinity interaction between Fc and TRIM21 PRYSPRY domain. Following binding of intracellular antibody, TRIM21 acts as both antiviral effector and sensor for innate immune signalling. These activities serve to reduce viral replication by orders of magnitude in vitro and contribute to host survival during in vivo infection. Neutralization occurs rapidly after detection and requires the activity of the ubiquitin-proteasome system. The microbial targets of this arm of intracellular immunity are still being identified: TRIM21 activity has been reported following infection by several non-enveloped viruses and intracellular bacteria. These findings extend the sphere of influence of antibodies to the intracellular domain and have broad implications for immunity. TRIM21 has been implicated in the chronic auto-immune condition systemic lupus erythematosus and is itself an auto-antigen in Sjögren’s syndrome. This review summarises our current understanding of TRIM21’s role as a cytosolic Fc receptor and briefly discusses pathological circumstances where intracellular antibodies have been described, or are hypothesized to occur, and may benefit from further investigations of the role of TRIM21.

  1. Improvement of Springback Predictability after forming and trimming

    NARCIS (Netherlands)

    Avetisyan, Marianna; Meinders, Vincent T.; Huetink, Han; Storen, S.

    2004-01-01

    When a sheet metal forming operation, such as deep drawing, is followed by a trimming operation the numerical springback after trimming is influenced by physical parameters and loss of product stiffness due to cutting off the material. Moreover, it is affected by the finite element mesh disturbance

  2. Role of TRIM33 in Wnt signaling during mesendoderm differentiation.

    Science.gov (United States)

    Xia, Xiaojie; Zuo, Feifei; Luo, Maoguo; Sun, Ye; Bai, Jianbo; Xi, Qiaoran

    2017-10-01

    Tripartite motif 33 (TRIM33), a member of the transcription intermediate factor 1 (TIF1) family of transcription cofactors, mediates transforming growth factor-beta (TGF-β) signaling through its PHD-Bromo cassette in mesendoderm differentiation during early mouse embryonic development. However, the role of the TRIM33 RING domain in embryonic differentiation is less clear. Here, we report that TRIM33 mediates Wnt signaling by directly regulating the expression of a specific subset of Wnt target genes, and this action is independent of its RING domain. We show that TRIM33 interacts with β-catenin, a central player in Wnt signaling in mouse embryonic stem cells (mESCs). In contrast to previous reports in cancer cell lines, the RING domain does not appear to function as the E3 ligase for β-catenin, since neither knockout nor overexpression of TRIM33 had an effect on β-catenin protein levels in mESCs. Furthermore, we show that although TRIM33 seems to be dispensable for Wnt signaling through a reporter assay, loss of TRIM33 significantly impairs the expression of a subset of Wnt target genes, including Mixl1, in a Wnt signaling-dependent manner. Together, our results indicate that TRIM33 regulates Wnt signaling independent of the E3 ligase activity of its RING domain for β-catenin in mESCs.

  3. Statistical Methodological Issues in Studies of Air Pollution and Respiratory Disease.

    OpenAIRE

    Hyndman, R.J.; Erbas, B.

    2001-01-01

    Epidemiological studies have consistently shown short term associations between levels of air pollution and respiratory disease in countries of diverse populations, geographical locations and varying levels of air pollution and climate. The aims of this paper are: (1) to assess the sensitivity of the observed pollution effects to model specification, with particular emphasis on the inclusion of seasonally adjusted covariates; and (2) to study the effect of air pollution on respiratory disease...

  4. Towards a performance assessment methodology using computational simulation for air distribution system designs in operating rooms

    NARCIS (Netherlands)

    Melhado, M.D.A.

    2012-01-01

    One of the important performance requirements for an air distribution system for an operating room (OR) is to provide good indoor environmental conditions in which to perform operations. Important conditions in this respect relate to the air quality and to the thermal conditions for the surgical

  5. Supporting the Future Total Force: A Methodology for Evaluating Potential Air National Guard Mission Assignments

    National Research Council Canada - National Science Library

    Lynch, Kristin F; Drew, John G; Sleeper, Sally; Williams, William A; Masters, James M; Luangkesorn, Louis; Tripp, Robert S; Lichter, Dahlia S; Roll, Charles R

    2007-01-01

    ... trained, highly experienced personnel with no aircraft to operate and support. The authors develop a methodology to evaluate missions that could be transferred from the active component to the ANG without significant cost to the total force...

  6. Trimming and procrastination as inversion techniques

    Science.gov (United States)

    Backus, George E.

    1996-12-01

    By examining the processes of truncating and approximating the model space (trimming it), and by committing to neither the objectivist nor the subjectivist interpretation of probability (procrastinating), we construct a formal scheme for solving linear and non-linear geophysical inverse problems. The necessary prior information about the correct model xE can be either a collection of inequalities or a probability measure describing where xE was likely to be in the model space X before the data vector y0 was measured. The results of the inversion are (1) a vector z0 that estimates some numerical properties zE of xE; (2) an estimate of the error δz = z0 - zE. As y0 is finite dimensional, so is z0, and hence in principle inversion cannot describe all of xE. The error δz is studied under successively more specialized assumptions about the inverse problem, culminating in a complete analysis of the linear inverse problem with a prior quadratic bound on xE. Our formalism appears to encompass and provide error estimates for many of the inversion schemes current in geomagnetism, and would be equally applicable in geodesy and seismology if adequate prior information were available there. As an idealized example we study the magnetic field at the core-mantle boundary, using satellite measurements of field elements at sites assumed to be almost uniformly distributed on a single spherical surface. Magnetospheric currents are neglected and the crustal field is idealized as a random process with rotationally invariant statistics. We find that an appropriate data compression diagonalizes the variance matrix of the crustal signal and permits an analytic trimming of the idealized problem.

  7. Physics-Based Aeroelastic Analysis for Future Air Vehicle Concepts Using a Fully Nonlinear Methodology

    National Research Council Canada - National Science Library

    Strganac, Thomas W

    2007-01-01

    Future air vehicles will be highly flexible and will include deformable sub-systems resulting in new physical interactions between a vehicle's structure, the surrounding flowfleld, and the dynamics...

  8. Antibody- and TRIM21-dependent intracellular restriction of Salmonella enterica.

    Science.gov (United States)

    Rakebrandt, Nikolas; Lentes, Sabine; Neumann, Heinz; James, Leo C; Neumann-Staubitz, Petra

    2014-11-01

    TRIM21 ('tripartite motif-containing protein 21', Ro52) is a ubiquitously expressed cytosolic Fc receptor, which has a potent role in protective immunity against nonenveloped viruses. TRIM21 mediates intracellular neutralisation of antibody-coated viruses, a process called ADIN (antibody-dependent intracellular neutralisation). Our results reveal a similar mechanism to fight bacterial infections. TRIM21 is recruited to the intracellular pathogen Salmonella enterica in epithelial cells early in infection. TRIM21 does not bind directly to S. enterica, but to antibodies opsonising it. Most importantly, bacterial restriction is dependent on TRIM21 as well as on the opsonisation state of the bacteria. Finally, Salmonella and TRIM21 colocalise with the autophagosomal marker LC3, and intracellular defence is enhanced in starved cells suggesting an involvement of the autophagocytic pathway. Our data extend the protective role of TRIM21 from viruses to bacteria and thereby strengthening the general role of ADIN in cellular immunity. © 2014 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

  9. Utilization of smoked salmon trim in extruded smoked salmon jerky.

    Science.gov (United States)

    Kong, J; Dougherty, M P; Perkins, L B; Camire, M E

    2012-06-01

    During smoked salmon processing, the dark meat along the lateral line is removed before packaging; this by-product currently has little economic value. In this study, the dark meat trim was incorporated into an extruded jerky. Three formulations were processed: 100% smoked trim, 75% : 25% smoked trim : fresh salmon fillet, and 50% : 50% smoked trim : fresh salmon blends (w/w basis). The base formulation contained salmon (approximately 83.5%), tapioca starch (8%), pregelatinized potato starch (3%), sucrose (4%), salt (1.5%), sodium nitrate (0.02%), and ascorbyl palmitate (0.02% of the lipid content). Blends were extruded in a laboratory-scale twin-screw extruder and then hot-smoked for 5 h. There were no significant differences among formulations in moisture, water activity, and pH. Protein was highest in the 50 : 50 blend jerky. Ash content was highest in the jerky made with 100% trim. Total lipids and salt were higher in the 100% trim jerky than in the 50 : 50 blend. Hot smoking did not adversely affect docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA) content in lipids from 100% smoked trim jerky. Servings of salmon jerky made with 75% and 100% smoked trim provided at least 500 mg of EPA and DHA. The 50 : 50 formulation had the highest Intl. Commission on Illumination (CIE) L*, a*, and b* color values. Seventy consumers rated all sensory attributes as between "like slightly" and "like moderately." With some formulation and processing refinements, lateral line trim from smoked salmon processors has potential to be incorporated into acceptable, healthful snack products. Dark meat along the lateral line is typically discarded by smoked salmon processors. This omega-3 fatty acid rich by-product can be used to make a smoked salmon jerky that provides a convenient source of these healthful lipids for consumers. © 2012 Institute of Food Technologists®

  10. Can citizen science produce good science? Testing the OPAL Air Survey methodology, using lichens as indicators of nitrogenous pollution.

    Science.gov (United States)

    Tregidgo, Daniel J; West, Sarah E; Ashmore, Mike R

    2013-11-01

    Citizen science is having increasing influence on environmental monitoring as its advantages are becoming recognised. However methodologies are often simplified to make them accessible to citizen scientists. We tested whether a recent citizen science survey (the OPAL Air Survey) could detect trends in lichen community composition over transects away from roads. We hypothesised that the abundance of nitrophilic lichens would decrease with distance from the road, while that of nitrophobic lichens would increase. The hypothesised changes were detected along strong pollution gradients, but not where the road source was relatively weak, or background pollution relatively high. We conclude that the simplified OPAL methodology can detect large contrasts in nitrogenous pollution, but it may not be able to detect more subtle changes in pollution exposure. Similar studies are needed in conjunction with the ever-growing body of citizen science work to ensure that the limitations of these methods are fully understood. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. Application of Various Lasers to Laser Trimming Resistance System

    Institute of Scientific and Technical Information of China (English)

    SUN Ji-feng

    2007-01-01

    Though the laser trimming resistance has been an old laser machining industry for over 30 years, the development of technology brings new alternative lasers which can be used for the traditional machining. The paper describes application of various lasers to laser trimming resistance system including early traditional krypton arc lamp pumped Nd:YAG to laser, modern popular diode pumped solid state laser and the present advanced harmonic diode pumped solid state laser. Using the new alternative lasers in the laser trimming resistance system can dramatically improve the yields and equipment performance.

  12. Air pollution and cardiovascular and respiratory disease: Rationale and methodology of CAPACITY study

    Science.gov (United States)

    Rabiei, Katayoun; Hosseini, Sayed Mohsen; Sadeghi, Erfan; Jafari-Koshki, Tohid; Rahimi, Mojtaba; Shishehforoush, Mansour; Lahijanzadeh, Ahmadreza; Sadeghian, Babak; Moazam, Elham; Mohebi, Mohammad Bagher; Ezatian, Victoria; Sarrafzadegan, Nizal

    2017-01-01

    BACKGROUND Considering the high level of air pollution and its impact on health, we aimed to study the correlation of air pollution with hospitalization and mortality of cardiovascular (CVD) and respiratory diseases (ResD) (CAPACITY) to determine the effects of air pollutants on CVD and ResD hospitalizations and deaths in Isfahan, Iran. METHODS Hourly levels of air pollutants including particulate matter (PM), carbon monoxide (CO), nitrogen dioxide (NO2), sulfur dioxide (SO2), and ozone (O3), information of CVD and ResD admissions and death certificate were obtained respectively from Department of Environment (DOE), Iran, hospitals and cemetery. Time series and case-crossover model were used to find the impact of air pollutants. This paper only summarizes the descriptive findings of the CAPACITY study. RESULTS The total number of hospitalized patients were 23781 in 2010 and 22485 in 2011. The most frequent cause of hospitalization and death was ischemic heart diseases in both years. While the mean annual levels of O3, CO, and PM10 were lower in 2011 than in 2010, NO2 and SO2 levels higher in 2011. In both years, PM10 was similarly increased during last month of fall, late spring and early summer. In 2011, the PM2.5 and PM10 monthly trend of change were similar. CONCLUSION The CAPACITY study is one of the few large-scale studies that evaluated the effects of air pollutants on a variety of CVD and ResD in a large city of Iran. This study can provide many findings that could clarify the effects of these pollutants on the incidence and burden of both disease groups. PMID:29643921

  13. Air pollution and cardiovascular and respiratory disease: Rationale and methodology of CAPACITY study.

    Science.gov (United States)

    Rabiei, Katayoun; Hosseini, Sayed Mohsen; Sadeghi, Erfan; Jafari-Koshki, Tohid; Rahimi, Mojtaba; Shishehforoush, Mansour; Lahijanzadeh, Ahmadreza; Sadeghian, Babak; Moazam, Elham; Mohebi, Mohammad Bagher; Ezatian, Victoria; Sarrafzadegan, Nizal

    2017-11-01

    Considering the high level of air pollution and its impact on health, we aimed to study the correlation of air pollution with hospitalization and mortality of cardiovascular (CVD) and respiratory diseases (ResD) (CAPACITY) to determine the effects of air pollutants on CVD and ResD hospitalizations and deaths in Isfahan, Iran. Hourly levels of air pollutants including particulate matter (PM), carbon monoxide (CO), nitrogen dioxide (NO2), sulfur dioxide (SO2), and ozone (O3), information of CVD and ResD admissions and death certificate were obtained respectively from Department of Environment (DOE), Iran, hospitals and cemetery. Time series and case-crossover model were used to find the impact of air pollutants. This paper only summarizes the descriptive findings of the CAPACITY study. The total number of hospitalized patients were 23781 in 2010 and 22485 in 2011. The most frequent cause of hospitalization and death was ischemic heart diseases in both years. While the mean annual levels of O3, CO, and PM10 were lower in 2011 than in 2010, NO2 and SO2 levels higher in 2011. In both years, PM10 was similarly increased during last month of fall, late spring and early summer. In 2011, the PM2.5 and PM10 monthly trend of change were similar. The CAPACITY study is one of the few large-scale studies that evaluated the effects of air pollutants on a variety of CVD and ResD in a large city of Iran. This study can provide many findings that could clarify the effects of these pollutants on the incidence and burden of both disease groups.

  14. Air pollution and cardiovascular and respiratory disease: Rationale and methodology of CAPACITY study

    Directory of Open Access Journals (Sweden)

    Katayoun Rabiei

    2017-11-01

    Full Text Available BACKGROUND: Considering the high level of air pollution and its impact on health, we aimed to study the correlation of air pollution with hospitalization and mortality of cardiovascular (CVD and respiratory diseases (ResD (CAPACITY to determine the effects of air pollutants on CVD and ResD hospitalizations and deaths in Isfahan, Iran.METHODS: Hourly levels of air pollutants including particulate matter (PM, carbon monoxide (CO, nitrogen dioxide (NO2, sulfur dioxide (SO2, and ozone (O3, information of CVD and ResD admissions and death certificate were obtained respectively from Department of Environment (DOE, Iran, hospitals and cemetery. Time series and case-crossover model were used to find the impact of air pollutants. This paper only summarizes the descriptive findings of the CAPACITY study.RESULTS: The total number of hospitalized patients were 23781 in 2010 and 22485 in 2011. The most frequent cause of hospitalization and death was ischemic heart diseases in both years. While the mean annual levels of O3, CO, and PM10 were lower in 2011 than in 2010, NO2 and SO2 levels higher in 2011. In both years, PM10 was similarly increased during last month of fall, late spring and early summer. In 2011, the PM2.5 and PM10 monthly trend of change were similar.CONCLUSION: The CAPACITY study is one of the few large-scale studies that evaluated the effects of air pollutants on a variety of CVD and ResD in a large city of Iran. This study can provide many findings that could clarify the effects of these pollutants on the incidence and burden of both disease groups. 

  15. A Methodology for Data Structure Assessment in Higher Education Administration. AIR Forum Paper 1978.

    Science.gov (United States)

    Baltes, Kenneth G.; Hendrix, Vernon L.

    Two recent developments in management information system technology and higher education administration have brought about the need for this study, designed to develop a methodology for revealing a relational model of the data base that administrators are operating from currently or would like to be able to operate from in the future.…

  16. The molluscan RING-finger protein L-TRIM is essential for neuronal outgrowth

    NARCIS (Netherlands)

    van Diepen, M. T.; Spencer, G.E.; Minnen, J.; Gouwenberg, Y.; Bouwman, J.G.; Smit, A. B.; van Kesteren, R.E.

    2005-01-01

    The tripartite motif proteins TRIM-2 and TRIM-3 have been put forward as putative organizers of neuronal outgrowth and structural plasticity. Here, we identified a molluscan orthologue of TRIM-2/3, named L-TRIM, which is up-regulated during in vitro neurite outgrowth of central neurons. In adult

  17. Development of Atmospheric Air 85Kr Monitoring Methodology on the Territory of the USSR

    Science.gov (United States)

    Pakhomov, Sergei; Dubasov, Yury

    2014-05-01

    Highly sensitive, low-background and high-performance method of beta-radioactivity measurements of the gas samples was developed in mid-eighties at Khlopin Radium institute. This method was based on the use of the serial automated installation for liquid scintillation measurements and special scintillating cells. Cells were equipped with the gas valve, and their internal surface were covered by a thin layer of organic scintillator. This method found was successfully was applied for 85Kr activity measurements in atmospheric krypton samples and for 85Kr concentration measurements in atmospheric air. For the first time, method developed for 85Kr activity measurements, was practically tested in May - June, 1986, while studying radioactive pollution characteristics in the air basin of Russia and Ukraine after the Chernobyl NPP accident. Thus for sampling of atmospheric krypton the industrial krypton-xenon mix manufactured at air-separating plants, located in the cities of Cherepovets, Lipetsk, Krivoi Rog and Enakiyevo was used. In the end of April and in the first half of May it was determined that 1,5-fold excess concentrations of 85Kr in atmospheric air were observed in atmospheric air of considerable part of the European territory of Russia and Ukraine During the period from 1987 to 1991 this method was used for monitoring of 85Kr on the territory of the former USSR in the air basin of Russia, Ukraine and Kazakhstan. Industrial krypton-xenon mix manufactured at 14 large air-separating plants was also used for sampling. Six of them were situated in Russia (Novomoskovsk, Lipetsk, Cherepovets, Chelyabinsk, Nizhni Tagil, Orsk). Seven - in Ukraine (Enakiyevo, Kommunarsk, Krivoi Rog, Makeyevka, Mariupol, Severodonetsk, Dneprodzerzhinsk). One plant was situated in Temirtau, in Kazakhstan. The analysis indicated that in Krivoi Rog; Dneprozhzerzhinsk; Severodonetsk; Makeyevka; Mariupol; Enakiyevo; Kommunarsk; Novomoskovsk and Cherepovets the average 85Kr concentration in

  18. Automatic channel trimming for control systems: A concept

    Science.gov (United States)

    Vandervoort, R. J.; Sykes, H. A.

    1977-01-01

    Set of bias signals added to channel inputs automatically normalize differences between channels. Algorithm and second feedback loop compute trim biases. Concept could be applied to regulators and multichannel servosystems for remote manipulators in undersea mining.

  19. Old trims for new: the cheaper solution to valve problems

    Energy Technology Data Exchange (ETDEWEB)

    Katz, B [Control Components, Inc., Rancho Santa Margarita, CA (United States)

    1994-01-01

    Rather than replacing a faulty valve - or one that is simply not up to the job - it has been possible to retrofit a variety of valve types used in nuclear plants with new trims which are described briefly. (Author).

  20. Old trims for new: the cheaper solution to valve problems

    International Nuclear Information System (INIS)

    Katz, B.

    1994-01-01

    Rather than replacing a faulty valve - or one that is simply not up to the job - it has been possible to retrofit a variety of valve types used in nuclear plants with new trims which are described briefly. (Author)

  1. Wrinkling reduction of membrane structure by trimming edges

    Directory of Open Access Journals (Sweden)

    Mingjun Liu

    2017-05-01

    Full Text Available Thin membranes have negligible bending stiffness, compressive stresses inevitably lead to wrinkling. Therefore, it is important to keep the surface of membrane structures flat in order to guarantee high precision. Edge-trimming is an effective method to passively diminish wrinkles, however a key difficulty in this process is the determination of the optimal trimming level. In this paper, regular polygonal membrane structures subjected to equal radial forces were analyzed, and a new stress field distribution model for arc-edge square membrane structure was proposed to predict the optimal trimming level. This model is simple and applicable to any polygonal membrane structures. Comparison among the results of the finite element analysis, and the experimental and analytical results showed that the proposed model accurately described the stress field distribution and guaranteed that there are no wrinkles appear inside the effective inscribed circle region for the optimal trimming level.

  2. Investigation of an automatic trim algorithm for restructurable aircraft control

    Science.gov (United States)

    Weiss, J.; Eterno, J.; Grunberg, D.; Looze, D.; Ostroff, A.

    1986-01-01

    This paper develops and solves an automatic trim problem for restructurable aircraft control. The trim solution is applied as a feed-forward control to reject measurable disturbances following control element failures. Disturbance rejection and command following performances are recovered through the automatic feedback control redesign procedure described by Looze et al. (1985). For this project the existence of a failure detection mechanism is assumed, and methods to cope with potential detection and identification inaccuracies are addressed.

  3. Trimming the UCERF2 hazard logic tree

    Science.gov (United States)

    Porter, Keith A.; Field, Edward H.; Milner, Kevin

    2012-01-01

    The Uniform California Earthquake Rupture Forecast 2 (UCERF2) is a fully time‐dependent earthquake rupture forecast developed with sponsorship of the California Earthquake Authority (Working Group on California Earthquake Probabilities [WGCEP], 2007; Field et al., 2009). UCERF2 contains 480 logic‐tree branches reflecting choices among nine modeling uncertainties in the earthquake rate model shown in Figure 1. For seismic hazard analysis, it is also necessary to choose a ground‐motion‐prediction equation (GMPE) and set its parameters. Choosing among four next‐generation attenuation (NGA) relationships results in a total of 1920 hazard calculations per site. The present work is motivated by a desire to reduce the computational effort involved in a hazard analysis without understating uncertainty. We set out to assess which branching points of the UCERF2 logic tree contribute most to overall uncertainty, and which might be safely ignored (set to only one branch) without significantly biasing results or affecting some useful measure of uncertainty. The trimmed logic tree will have all of the original choices from the branching points that contribute significantly to uncertainty, but only one arbitrarily selected choice from the branching points that do not.

  4. Measurements of air kerma index in computed tomography: a comparison among methodologies

    Energy Technology Data Exchange (ETDEWEB)

    Alonso, T. C.; Mourao, A. P.; Da Silva, T. A., E-mail: alonso@cdtn.br [Universidade Federal de Minas Gerais, Programa de Ciencia y Tecnicas Nucleares, Av. Pres. Antonio Carlos 6627, Pampulha, 31270-901 Belo Horizonte, Minas Gerais (Brazil)

    2016-10-15

    Computed tomography (CT) has become the most important and widely used technique for diagnosis purpose. As CT exams impart high doses to patients in comparison to other radiologist techniques, reliable dosimetry is required. Dosimetry in CT is done in terms of air kerma index in air or in a phantom measured by a pencil ionization chamber under a single X-ray tube rotation. In this work, a comparison among CT dosimetric quantities measured by an UNFORS pencil ionization chamber, MTS-N RADOS thermoluminescent dosimeters and GAFCHROMIC XR-CT radiochromic film was done. The three dosimetric systems were properly calibrated in X-ray reference radiations in a calibration laboratory. CT dosimetric quantities were measured in CT Bright Speed GE Medical Systems Inc., scanner in a PMMA trunk phantom and a comparison among the three dosimetric techniques was done. (Author)

  5. CrIS/ATMS Retrievals Using the Latest AIRS/AMSU Retrieval Methodology

    Science.gov (United States)

    Susskind, Joel; Kouvaris, Louis C.; Blaisdell, John; Iredell, Lena

    2015-01-01

    This research is being done under the NPP Science Team Proposal: Analysis of CrISATMS Using an AIRS Version 6-like Retrieval Algorithm Objective: Generate a long term CrISATMS level-3 data set that is consistent with that of AIRSAMSU Approach: Adapt the currently operational AIRS Science Team Version-6 Retrieval Algorithm, or an improved version of it, for use with CrISATMS data. Metric: Generate monthly mean level-3 CrISATMS climate data sets and evaluate the results by comparison of monthly mean AIRSAMSU and CrISATMS products, and more significantly, their inter-annual differences and, eventually, anomaly time series. The goal is consistency between the AIRSAMSU and CrISATMS climate data sets.

  6. Measurements of air kerma index in computed tomography: a comparison among methodologies

    International Nuclear Information System (INIS)

    Alonso, T. C.; Mourao, A. P.; Da Silva, T. A.

    2016-10-01

    Computed tomography (CT) has become the most important and widely used technique for diagnosis purpose. As CT exams impart high doses to patients in comparison to other radiologist techniques, reliable dosimetry is required. Dosimetry in CT is done in terms of air kerma index in air or in a phantom measured by a pencil ionization chamber under a single X-ray tube rotation. In this work, a comparison among CT dosimetric quantities measured by an UNFORS pencil ionization chamber, MTS-N RADOS thermoluminescent dosimeters and GAFCHROMIC XR-CT radiochromic film was done. The three dosimetric systems were properly calibrated in X-ray reference radiations in a calibration laboratory. CT dosimetric quantities were measured in CT Bright Speed GE Medical Systems Inc., scanner in a PMMA trunk phantom and a comparison among the three dosimetric techniques was done. (Author)

  7. Loss of heterozygosity of TRIM3 in malignant gliomas

    International Nuclear Information System (INIS)

    Boulay, Jean-Louis; Stiefel, Urs; Taylor, Elisabeth; Dolder, Béatrice; Merlo, Adrian; Hirth, Frank

    2009-01-01

    Malignant gliomas are frequent primary brain tumors associated with poor prognosis and very limited response to conventional chemo- and radio-therapies. Besides sharing common growth features with other types of solid tumors, gliomas are highly invasive into adjacent brain tissue, which renders them particularly aggressive and their surgical resection inefficient. Therefore, insights into glioma formation are of fundamental interest in order to provide novel molecular targets for diagnostic purposes and potential anti-cancer drugs. Human Tripartite motif protein 3 (TRIM3) encodes a structural homolog of Drosophila brain tumor (brat) implicated in progenitor cell proliferation control and cancer stem cell suppression. TRIM3 is located within the loss of allelic heterozygosity (LOH) hotspot of chromosome segment 11p15.5, indicating a potential role in tumor suppression. ... Here we analyze 70 primary human gliomas of all types and grades and report somatic deletion mapping as well as single nucleotide polymorphism analysis together with quantitative real-time PCR of chromosome segment 11p15.5. Our analysis identifies LOH in 17 cases (24%) of primary human glioma which defines a common 130 kb-wide interval within the TRIM3 locus as a minimal area of loss. We further detect altered genomic dosage of TRIM3 in two glioma cases with LOH at 11p15.5, indicating homozygous deletions of TRIM3. Loss of heterozygosity of chromosome segment 11p15.5 in malignant gliomas suggests TRIM3 as a candidate brain tumor suppressor gene

  8. Evaluation of the environmental epidemiologic data and methodology for the air quality standard in Beijing

    Science.gov (United States)

    Li, Xu; Jiang, Yanfeng; Yin, Ling; Liu, Bo; Du, Pengfei; Hassan, Mujtaba; Wang, Shigong; Li, Tanshi

    2017-09-01

    To evaluate the relationship between exposure to air pollutants and respiratory emergency room visits, a generalized additive model (GAM) was used to analyze the exposure-effect relationship between air pollutants and respiratory emergency room visits. The results showed that NO2, SO2, and PM10 have positive relationships with respiratory disease. Concentration increases of 10 μg/m3 in NO2, SO2, and PM10 corresponded to 3.90% (95%CI 3.56-4.25), 0.81% (95%CI -0.09-1.72), and 0.64% (95%CI 0.55-0.74) increases in respiratory emergency room visits. In addition, there is a strong synergic effect of PM10 and NO2 on respiratory diseases. The threshold values of the national standard grade II limits used in Beijing should be adjusted. An appropriate standard could effectively promote a significant decline in respiratory room visits and would eventually be beneficial to air quality management in residential areas.

  9. Evaluation of different numerical methodologies for dispersion of air pollutants in an urban environment

    International Nuclear Information System (INIS)

    Mumovic, D.; Crowther, J.M.; Stevanovic, Z.

    2003-01-01

    Since 1950 the world population has more than doubled but meanwhile the global number of cars has increased by a factor of 10. In that same period the fraction of people living in urban areas has increased by a factor of 4. Apart from large point-sources of local air pollution, traffic induced pollution is now the most significant contributor to urban air quality in city centres, particularly for carbon monoxide, oxides of nitrogen and fine particulate matter. Until recently, pollutant dispersion in urban areas has usually been numerically investigated by using empirical models, such as the Gaussian plume model, or by extensions of this technique to line sources and multiple sources. More recently, advanced computational fluid dynamics (CFD) simulations have been attempted but have been mainly two-dimensional and often encompassing only a single street canyon. This paper provides a comprehensive, critical evaluation of dispersion of pollutants in urban areas. A three-dimensional flow model has been set-up for a staggered crossroad, using the Navier-Stokes equations and the conservation equation for species concentration. The effect of using several different turbulence models, including the k-ε model, modifications and extensions, has been investigated. Cartesian coordinates have been used in connection with the Partial Solution Algorithm (PARSOL) and Body Fitted Coordinates (BFC). The effects of several different numerical algorithms for discretization of differential equations have also been studied. More than thirty cases are analysed, and the main results are compared with wind tunnel experiments. The numerical results are presented as non-dimensional values to facilitate comparison between experimental and numerical studies. It has been shown that the numerical studies have been able to simulate the air-flow in urban areas and confirm, qualitatively, the previous field observations and wind tunnel results. This success encouraged the authors to extend such

  10. Evaluation of different numerical methodologies for dispersion of air pollutants in an urban environment

    Energy Technology Data Exchange (ETDEWEB)

    Mumovic, D.; Crowther, J.M. [Glasgow Caledonian Univ., School of Built and Natural Environment, Glasgow (United Kingdom)]. E-mail: dmumov10@caledonian.ac.uk; Stevanovic, Z. [Univ. of Belgrade, Inst. of Nuclear Sciences, Belgrade (Serbia and Montenegro)

    2003-07-01

    Since 1950 the world population has more than doubled but meanwhile the global number of cars has increased by a factor of 10. In that same period the fraction of people living in urban areas has increased by a factor of 4. Apart from large point-sources of local air pollution, traffic induced pollution is now the most significant contributor to urban air quality in city centres, particularly for carbon monoxide, oxides of nitrogen and fine particulate matter. Until recently, pollutant dispersion in urban areas has usually been numerically investigated by using empirical models, such as the Gaussian plume model, or by extensions of this technique to line sources and multiple sources. More recently, advanced computational fluid dynamics (CFD) simulations have been attempted but have been mainly two-dimensional and often encompassing only a single street canyon. This paper provides a comprehensive, critical evaluation of dispersion of pollutants in urban areas. A three-dimensional flow model has been set-up for a staggered crossroad, using the Navier-Stokes equations and the conservation equation for species concentration. The effect of using several different turbulence models, including the k-{epsilon} model, modifications and extensions, has been investigated. Cartesian coordinates have been used in connection with the Partial Solution Algorithm (PARSOL) and Body Fitted Coordinates (BFC). The effects of several different numerical algorithms for discretization of differential equations have also been studied. More than thirty cases are analysed, and the main results are compared with wind tunnel experiments. The numerical results are presented as non-dimensional values to facilitate comparison between experimental and numerical studies. It has been shown that the numerical studies have been able to simulate the air-flow in urban areas and confirm, qualitatively, the previous field observations and wind tunnel results. This success encouraged the authors to extend

  11. From 1962 the teaching of Methodology of Radioisotopes is continuous in the University of Buenos Aires of the Argentine Republic

    International Nuclear Information System (INIS)

    Rivera, E.; Cremaschi, G.; Martin, G.; Zubillaga, M.; Cricco, G.; Davio, C.; Genaro, A.; Bianchin, A.; Mohamad, N.; Klecha, A.; Calmanovici, G.; Goldman, G.; Salgueiro, J.; Nunez, M.; Medina, V.; Gutierrez, A.; Leonardi, N.; Bergoc, R.

    2006-01-01

    In the Faculty of Pharmacy and Biochemistry of the University of Buenos Aires the teaching of the radioisotopes began in 1960 and uninterruptedly continuous. The application of the radioisotopes and the radiations in different professional activities it is acceptable only in a context of radiological safety and with personal appropriately trained. Conscious of it, the training in grade, postgraduate and technicature, has more of 40% of the thematic one guided to the formation in radiological protection. The courses dictated at the moment in the Laboratory of Radioisotopes they include: Grade formation: to) Subject grade 'Methodology of Radioisotopes' in the Career of Biochemistry: it began to be dictated in 1960 and until the present, more of 6500 students they have gone by our classrooms. b) Grade subject 'Radiopharmacy' in the Career of Pharmacy: guided to the formation of a modern pharmacist, with necessary knowledge to be developed as professional in the Radiopharmaceutical area. Postgraduate formation: c) Postgraduate course of Methodology of Radioisotopes specially directed to biochemical, biologists, veterinarians, chemical. It is dictated uninterruptedly from 1962. d) Postgraduate course in Methodology of Radioisotopes for medical professionals, specially directed to professionals of the medicine that want to specialize in different branches of the Nuclear Medicine. Both courses have 220 present hours and it stops their approval the assistants they should surrender a final exam at open book that consists on the resolution of a practical exercise adapted to their professional practices. Until the present they have surrendered their exams satisfactorily approximately 2000 professionals coming from different areas of the Argentina and of several countries of Hispanic speech. e) Starting from 1992 the Course of Upgrade in Methodology of Radioisotopes directed to professionals that want to upgrade its knowledge in new radioisotopic methodologies is dictated

  12. Methodologies for diagnosis of air pollution on plants:a review

    International Nuclear Information System (INIS)

    Hassan, I.A.; Ashmore, M.R.

    1996-01-01

    In all branches of science, the development of new techniques and methods of investigation is as central to progress as the formation of new ideas and theories. As the study of pollution effects on vegetation has progressed, new techniques and new metrological approaches have been developed, so that we now have a range of established methods which have been used to establish links between pollutant exposure and plant response. Nevertheless, progress in identifying the role of air pollution in the forest declines currently affecting many parts of europe has not been encouraging; although many hypotheses exist, convincing evidence in support of them is fragmentary. Why is this? Is it that we are faced with a problem of unparalleled complexity, which will take decades to resolve by whatever method? Or are the methods we are using inappropriate, and restricting the development of scientific understanding?

  13. Methodologies of health impact assessment as part of an integrated approach to reduce effects of air pollution

    Energy Technology Data Exchange (ETDEWEB)

    Aunan, K; Seip, H M

    1995-12-01

    Quantification of average frequencies of health effects on a population level is an essential part of an integrated assessment of pollution effects. Epidemiological studies seem to provide the best basis for such estimates. This paper gives an introduction to a methodology for health impact assessment and also the results from selected parts of a case study in Hungary. This case study is aimed at testing and improving the methodology for integrated assessment and focuses on energy production and consumption and implications for air pollution. Using monitoring data from Budapest, the paper gives estimates of excess frequencies of respiratory illness, mortality and other health end-points. For a number of health end-points, particles probably may serve as a good indicator component. Stochastic simulation is used to illustrate the uncertainties imbedded in the exposure-response function applied. The paper uses the ``bottom up approach`` to find cost-effective abatement strategies against pollution damages, where specific abatement measures such as emission standards for vehicles are explored in detail. It is concluded that in spite of large uncertainties in every step of the analysis, an integrated assessment of costs and benefits of different abatement measures is valuable as it clarifies the main objectives of an abatement policy and explicitly describes the adverse impacts of different activities and their relative importance. 46 refs., 11 figs., 2 tabs.

  14. National inventories of air emissions in France: organisation and methodology - 8. edition - OMINEA, February 2011

    International Nuclear Information System (INIS)

    Fontelle, Jean-Pierre; Allemand, Nadine; Andre, Jean-Marc; Bastide, Aurelie; Chang, Jean-Pierre; Deflorenne, Emmanuel; Druart, Ariane; Gavel, Antoine; Gueguen, Celine; Jabot, Julien; Jacquier, Guillaume; Joya, Romain; Kessouar, Sabrina; Martinet, Yann; Mathias, Etienne; Nicco, Laetitia; Prouteau, Emilie; Serveau, Laetitia; Tuddenham, Mark; Vincent, Julien

    2011-01-01

    Usually, various methods are used to estimate emissions of atmospheric pollutants from anthropogenic or natural sources. These methods which are more or less specific, require large quantities of data to carry out what is commonly named 'emission inventories', 'cadastres' or 'registers' depending on characteristics of the collection in terms of spatial and sectoral resolution. The OMINEA report includes a description of the national inventory system of pollutant emissions into the atmosphere (SNIEPA) which deals with the following topics: organisation, break down of responsibilities and coverage. Technical operational arrangements are described and various elements relating to reference documents and definitions, control and quality assurance, estimation of uncertainties are provided. A description is given for each emitting source category and for several substances classified in the following topics: 'greenhouse gases', 'acidification and photochemical pollution', 'eutrophication', 'heavy metals', 'persistent organic pollutants', 'particulate matter', 'other'. The plan is based on the international reporting format defined by the United Nations within the framework of conventions on climate change and long range transboundary air pollution (sources categories listed in CRFI/NFR)

  15. National inventories of air emissions in France: organisation and methodology - 9. edition - OMINEA, February 2011

    International Nuclear Information System (INIS)

    Fontelle, Jean-Pierre; Andre, Jean-Marc; Bastide, Aurelie; Bort, Romain; Chang, Jean-Pierre; Deflorenne, Emmanuel; Druart, Ariane; Gavel, Antoine; Gueguen, Celine; Jabot, Julien; Jacquier, Guillaume; Jeannot, Coralie; Joya, Romain; Kessouar, Sabrina; Martinet, Yann; Mathias, Etienne; Nicco, Laetitia; Serveau, Laetitia; Tuddenham, Mark; Vasudeva, Divya; Vincent, Julien

    2012-01-01

    Usually, various methods are used to estimate emissions of atmospheric pollutants from anthropogenic or natural sources. These methods which are more or less specific, require large quantities of data to carry out what is commonly named 'emission inventories', 'cadastres' or 'registers' depending on characteristics of the collection in terms of spatial and sectoral resolution. The OMINEA report includes a description of the national inventory system of pollutant emissions into the atmosphere (SNIEPA) which deals with the following topics: organisation, break down of responsibilities and coverage. Technical operational arrangements are described and various elements relating to reference documents and definitions, control and quality assurance, estimation of uncertainties are provided. A description is given for each emitting source category and for several substances classified in the following topics: 'greenhouse gases', 'acidification and photochemical pollution', 'eutrophication', 'heavy metals', 'persistent organic pollutants', 'particulate matter', 'other'. The plan is based on the international reporting format defined by the United Nations within the framework of conventions on climate change and long range transboundary air pollution (sources categories listed in CRFI/NFR)

  16. Matlab Stability and Control Toolbox: Trim and Static Stability Module

    Science.gov (United States)

    Crespo, Luis G.; Kenny, Sean P.

    2006-01-01

    This paper presents the technical background of the Trim and Static module of the Matlab Stability and Control Toolbox. This module performs a low-fidelity stability and control assessment of an aircraft model for a set of flight critical conditions. This is attained by determining if the control authority available for trim is sufficient and if the static stability characteristics are adequate. These conditions can be selected from a prescribed set or can be specified to meet particular requirements. The prescribed set of conditions includes horizontal flight, take-off rotation, landing flare, steady roll, steady turn and pull-up/ push-over flight, for which several operating conditions can be specified. A mathematical model was developed allowing for six-dimensional trim, adjustable inertial properties, asymmetric vehicle layouts, arbitrary number of engines, multi-axial thrust vectoring, engine(s)-out conditions, crosswind and gyroscopic effects.

  17. Non-local means filter for trim statics

    KAUST Repository

    Huang, Yunsong

    2014-08-05

    Structures will be mispositioned across prestack migration gathers in the presence of inaccuracies in the velocity model. Stacking these misaligned gathers runs the risk of destroying important structures in the stacked migration image. To mitigate this problem, we propose a trim statics inspired by the non-local means algorithm originally developed for image denoising. This method differs from the conventional one in two fundamental respects. First, the trim statics are computed by comparing image patches instead of individual image traces. Second, no global pilot trace is needed because only two migration images at a time participate in trim statics and are stacked into one image. A multitude of migration images are stacked recursively in this two-to-one fashion. Tests with a Gulf of Mexico dataset show a noticeable improvement in the feature coherency of the stacked migration image.

  18. Loss of heterozygosity of TRIM3 in malignant gliomas

    Directory of Open Access Journals (Sweden)

    Dolder Béatrice

    2009-02-01

    Full Text Available Abstract Background Malignant gliomas are frequent primary brain tumors associated with poor prognosis and very limited response to conventional chemo- and radio-therapies. Besides sharing common growth features with other types of solid tumors, gliomas are highly invasive into adjacent brain tissue, which renders them particularly aggressive and their surgical resection inefficient. Therefore, insights into glioma formation are of fundamental interest in order to provide novel molecular targets for diagnostic purposes and potential anti-cancer drugs. Human Tripartite motif protein 3 (TRIM3 encodes a structural homolog of Drosophila brain tumor (brat implicated in progenitor cell proliferation control and cancer stem cell suppression. TRIM3 is located within the loss of allelic heterozygosity (LOH hotspot of chromosome segment 11p15.5, indicating a potential role in tumor suppression. ... Methods Here we analyze 70 primary human gliomas of all types and grades and report somatic deletion mapping as well as single nucleotide polymorphism analysis together with quantitative real-time PCR of chromosome segment 11p15.5. Results Our analysis identifies LOH in 17 cases (24% of primary human glioma which defines a common 130 kb-wide interval within the TRIM3 locus as a minimal area of loss. We further detect altered genomic dosage of TRIM3 in two glioma cases with LOH at 11p15.5, indicating homozygous deletions of TRIM3. Conclusion Loss of heterozygosity of chromosome segment 11p15.5 in malignant gliomas suggests TRIM3 as a candidate brain tumor suppressor gene.

  19. Air traffic energy efficiency differs from place to place: analysis of historical trends by geographical zones using a macro-level methodology

    International Nuclear Information System (INIS)

    Cheze, Benoit; Gastineau, Pascal; Chevallier, Julien

    2011-01-01

    This article analyses energy efficiency coefficients and their evolution in the air transport sector. The proposed 'macro-level' methodology allows obtaining energy efficiency coefficients and their growth rates (corresponding to the evolution of energy gains) from 1983 to 2006 for eight distinct geographical regions and at the world level. During the whole period, energy efficiency improvements have been equal to 2.88% per year at the world level, with strong differences between regions. Moreover, our results indicate that domestic air travels are less energy efficient (i.e. more carbon intensive) than international air travels. This result applies in all regions. (authors)

  20. CFD-Based Over-Determined Trim Analysis for Optimum Aerodynamic Efficiency, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The overall objective of this Phase I project is to develop a nonlinear trim module in FUN3D for enabling the determined and over-determined trim analyses to be...

  1. TRIM E3 ligases interfere with early and late stages of the retroviral life cycle.

    Directory of Open Access Journals (Sweden)

    Pradeep D Uchil

    2008-02-01

    Full Text Available Members of the TRIpartite interaction Motif (TRIM family of E3 ligases have been shown to exhibit antiviral activities. Here we report a near comprehensive screen for antiretroviral activities of 55 TRIM proteins (36 human, 19 mouse. We identified approximately 20 TRIM proteins that, when transiently expressed in HEK293 cells, affect the entry or release of human immunodeficiency virus 1 (HIV, murine leukemia virus (MLV, or avian leukosis virus (ALV. While TRIM11 and 31 inhibited HIV entry, TRIM11 enhanced N-MLV entry by interfering with Ref1 restriction. Strikingly, many TRIM proteins affected late stages of the viral life cycle. Gene silencing of endogenously expressed TRIM 25, 31, and 62 inhibited viral release indicating that they play an important role at late stages of the viral life cycle. In contrast, downregulation of TRIM11 and 15 enhanced virus release suggesting that these proteins contribute to the endogenous restriction of retroviruses in cells.

  2. Prevalence and impact of chronic obstructive pulmonary disease in a rural district of Uganda : FRESH AIR methodology for sub-Saharan Africa

    NARCIS (Netherlands)

    van Gemert, Frederik

    2017-01-01

    Prevalence and impact of chronic obstructive pulmonary disease in a rural district of Uganda: FRESH AIR methodology for sub-Saharan Africa Worldwide, tobacco smoking is the most common encountered risk factor for chronic obstructive pulmonary disease (COPD). However, in many low and middle-income

  3. Compensation of the AKT signaling by ERK signaling in transgenic mice hearts overexpressing TRIM72

    International Nuclear Information System (INIS)

    Ham, Young-Mi; Mahoney, Sarah Jane

    2013-01-01

    The AKT and ERK signaling pathways are known to be involved in cell hypertrophy, proliferation, survival and differentiation. Although there is evidence for crosstalk between these two signaling pathways in cellulo, there is less evidence for cross talk in vivo. Here, we show that crosstalk between AKT and ERK signaling in the hearts of TRIM72-overexpressing transgenic mice (TRIM72-Tg) with alpha-MHC promoter regulates and maintains their heart size. TRIM72, a heart- and skeletal muscle-specific protein, downregulates AKT-mTOR signaling via IRS-1 degradation and reduces the size of rat cardiomyocytes and the size of postnatal TRIM72-Tg hearts. TRIM72 expression was upregulated by hypertrophic inducers in cardiomyocytes, while IRS-1 was downregulated by IGF-1. TRIM72 specifically regulated IGF-1-dependent AKT-mTOR signaling, resulting in a reduction of the size of cardiomyocytes. Postnatal TRIM72-Tg hearts were smaller than control-treated hearts with inhibition of AKT-mTOR signaling. However, adult TRIM72-Tg hearts were larger than of control despite the suppression of AKT-mTOR signaling. Activation of ERK, PKC-α, and JNK were observed to be elevated in adult TRIM72-Tg, and these signals were mediated by ET-1 via the ET receptors A and B. Altogether, these results suggest that AKT signaling regulates cardiac hypertrophy in physiological conditions, and ERK signaling compensates for the absence of AKT signaling during TRIM72 overexpression, leading to pathological hypertrophy. -- Highlights: • TRIM72 inhibits AKT signaling through ubiquitination of IRS-1 in cardiac cells. • TRIM72 regulates the size of cardiac cells. • TRIM72 regulates size of postnatal TRIM72-overexpressing transgenic mice hearts. • Adult TRIM72-overexpressing transgenic mice hearts showed cardiac dysfunction. • Adult TRIM72 transgenic mice hearts showed higher expression of endothelin receptors

  4. Compensation of the AKT signaling by ERK signaling in transgenic mice hearts overexpressing TRIM72

    Energy Technology Data Exchange (ETDEWEB)

    Ham, Young-Mi, E-mail: youngmi_ham@hms.harvard.edu [College of Life Science and Biotechnology, Korea University, Seoul (Korea, Republic of); Department of Cell Biology, Harvard Medical School, Boston, MA 02115 (United States); Mahoney, Sarah Jane [Department of Cell Biology, Harvard Medical School, Boston, MA 02115 (United States)

    2013-06-10

    The AKT and ERK signaling pathways are known to be involved in cell hypertrophy, proliferation, survival and differentiation. Although there is evidence for crosstalk between these two signaling pathways in cellulo, there is less evidence for cross talk in vivo. Here, we show that crosstalk between AKT and ERK signaling in the hearts of TRIM72-overexpressing transgenic mice (TRIM72-Tg) with alpha-MHC promoter regulates and maintains their heart size. TRIM72, a heart- and skeletal muscle-specific protein, downregulates AKT-mTOR signaling via IRS-1 degradation and reduces the size of rat cardiomyocytes and the size of postnatal TRIM72-Tg hearts. TRIM72 expression was upregulated by hypertrophic inducers in cardiomyocytes, while IRS-1 was downregulated by IGF-1. TRIM72 specifically regulated IGF-1-dependent AKT-mTOR signaling, resulting in a reduction of the size of cardiomyocytes. Postnatal TRIM72-Tg hearts were smaller than control-treated hearts with inhibition of AKT-mTOR signaling. However, adult TRIM72-Tg hearts were larger than of control despite the suppression of AKT-mTOR signaling. Activation of ERK, PKC-α, and JNK were observed to be elevated in adult TRIM72-Tg, and these signals were mediated by ET-1 via the ET receptors A and B. Altogether, these results suggest that AKT signaling regulates cardiac hypertrophy in physiological conditions, and ERK signaling compensates for the absence of AKT signaling during TRIM72 overexpression, leading to pathological hypertrophy. -- Highlights: • TRIM72 inhibits AKT signaling through ubiquitination of IRS-1 in cardiac cells. • TRIM72 regulates the size of cardiac cells. • TRIM72 regulates size of postnatal TRIM72-overexpressing transgenic mice hearts. • Adult TRIM72-overexpressing transgenic mice hearts showed cardiac dysfunction. • Adult TRIM72 transgenic mice hearts showed higher expression of endothelin receptors.

  5. Robust estimators based on generalization of trimmed mean

    Czech Academy of Sciences Publication Activity Database

    Adam, Lukáš; Bejda, P.

    (2018) ISSN 0361-0918 Institutional support: RVO:67985556 Keywords : Breakdown point * Estimators * Geometric median * Location * Trimmed mean Subject RIV: BA - General Mathematics Impact factor: 0.457, year: 2016 http://library.utia.cas.cz/separaty/2017/MTR/adam-0481224.pdf

  6. Influence of an accurate trimming operation on springback

    NARCIS (Netherlands)

    Avetisyan, Marianna; Meinders, Vincent T.; Huetink, Han

    2006-01-01

    When a sheet metal forming operation, such as deep drawing, is followed by a trimming operation the numerical springback is influenced by various physical parameters and numerical factors. Two techniques of taking into the account the stress state change due to cutting in the FE plate model are

  7. TRIM timber projections: an evaluation based on forest inventory measurements.

    Science.gov (United States)

    John R. Mills

    1989-01-01

    Two consecutive timberland inventories collected from permanent plots in the natural pine type in North Carolina were used to evaluate the timber resource inventory model (TRIM). This study compares model predictions with field measurements and examines the effect of inventory data aggregation on the accuracy of projections. Projections were repeated for two geographic...

  8. Prognostic indicators and the importance of trimming in noninfective ...

    African Journals Online (AJOL)

    Prognostic indicators and the importance of trimming in noninfective claw disorders in cattle. ... features of chronic laminitis occurred concurrently with heel or sole erosion, white line separation, sole ulcers, horizontal hoof wall fissures and double soles. In most smallholder farms, cows with these disorders were neglected to ...

  9. 33 CFR 401.30 - Ballast water and trim.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Ballast water and trim. 401.30... OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Seaway Navigation § 401.30 Ballast water... exclusive economic zone must agree to comply with the “Code of Best Practices for Ballast Water Management...

  10. The Timber Resource Inventory Model (TRIM): a projection model for timber supply and policy analysis.

    Science.gov (United States)

    P.L. Tedder; R.N. La Mont; J.C. Kincaid

    1987-01-01

    TRIM (Timber Resource Inventory Model) is a yield table projection system developed for timber supply projections and policy analysis. TRIM simulates timber growth, inventories, management and area changes, and removals over the projection period. Programs in the TRIM system, card-by-card descriptions of required inputs, table formats, and sample results are presented...

  11. A methodology for the evaluation of the turbine jet engine fragment threat to generic air transportable containers

    International Nuclear Information System (INIS)

    Harding, D.C.; Pierce, J.D.

    1993-06-01

    Uncontained, high-energy gas turbine engine fragments are a potential threat to air-transportable containers carried aboard jet aircraft. The threat to a generic example container is evaluated by probability analyses and penetration testing to demonstrate the methodology to be used in the evaluation of a specific container/aircraft/engine combination. Fragment/container impact probability is the product of the uncontained fragment release rate and the geometric probability that a container is in the path of this fragment. The probability of a high-energy rotor burst fragment from four generic aircraft engines striking one of the containment vessels aboard a transport aircraft is approximately 1.2 x 10 -9 strikes/hour. Finite element penetration analyses and tests can be performed to identify specific fragments which have the potential to penetrate a generic or specific containment vessel. The relatively low probability of engine fragment/container impacts is primarily due to the low release rate of uncontained, hazardous jet engine fragments

  12. 76 FR 72978 - Premier Trim, LLC, Spectrum Trim, LLC and Grant Products International, Inc. D/B/A Spectrum Grant...

    Science.gov (United States)

    2011-11-28

    ..., Spectrum Trim, LLC and Grant Products International, Inc. D/B/A Spectrum Grant De Mexico Including Workers Whose Unemployment Insurance (UI) Wages Are Paid Through Grant Products International, Inc... Brownsville, TX; Amended Certification Regarding Eligibility To Apply for Worker Adjustment Assistance In...

  13. TRIM5α association with cytoplasmic bodies is not required for antiretroviral activity

    International Nuclear Information System (INIS)

    Song, Byeongwoon; Diaz-Griffero, Felipe; Park, Do Hyun; Rogers, Thomas; Stremlau, Matthew; Sodroski, Joseph

    2005-01-01

    The tripartite motif (TRIM) protein, TRIM5α, restricts infection by particular retroviruses. Many TRIM proteins form cytoplasmic bodies of unknown function. We investigated the relationship between cytoplasmic body formation and the structure and antiretroviral activity of TRIM5α. In addition to diffuse cytoplasmic staining, the TRIM5α proteins from several primate species were located in cytoplasmic bodies of different sizes; by contrast, TRIM5α from spider monkeys did not form cytoplasmic bodies. Despite these differences, all of the TRIM5α proteins exhibited the ability to restrict infection by particular retroviruses. Treatment of cells with geldanamycin, an Hsp90 inhibitor, resulted in disappearance or reduction of the TRIM5α-associated cytoplasmic bodies, yet exerted little effect on the restriction of retroviral infection. Studies of green fluorescent protein-TRIM5α fusion proteins indicated that no TRIM5α domain is specifically required for association with cytoplasmic bodies. Apparently, the formation of cytoplasmic bodies is not required for the antiretroviral activity of TRIM

  14. A new time-series methodology for estimating relationships between elderly frailty, remaining life expectancy, and ambient air quality.

    Science.gov (United States)

    Murray, Christian J; Lipfert, Frederick W

    2012-01-01

    Many publications estimate short-term air pollution-mortality risks, but few estimate the associated changes in life-expectancies. We present a new methodology for analyzing time series of health effects, in which prior frailty is assumed to precede short-term elderly nontraumatic mortality. The model is based on a subpopulation of frail individuals whose entries and exits (deaths) are functions of daily and lagged environmental conditions: ambient temperature/season, airborne particles, and ozone. This frail susceptible population is unknown; its fluctuations cannot be observed but are estimated using maximum-likelihood methods with the Kalman filter. We used an existing 14-y set of daily data to illustrate the model and then tested the assumption of prior frailty with a new generalized model that estimates the portion of the daily death count allocated to nonfrail individuals. In this demonstration dataset, new entries into the high-risk pool are associated with lower ambient temperatures and higher concentrations of particulate matter and ozone. Accounting for these effects on antecedent frailty reduces this at-risk population, yielding frail life expectancies of 5-7 days. Associations between environmental factors and entries to the at-risk pool are about twice as strong as for mortality. Nonfrail elderly deaths are seen to make only small contributions. This new model predicts a small short-lived frail population-at-risk that is stable over a wide range of environmental conditions. The predicted effects of pollution on new entries and deaths are robust and consistent with conventional morbidity/mortality times-series studies. We recommend model verification using other suitable datasets.

  15. Helicopter Non-Unique Trim Strategies for Blade-Vortex Interaction (BVI) Noise Reduction

    Science.gov (United States)

    Malpica, Carlos; Greenwood, Eric; Sim, Ben W.

    2016-01-01

    An acoustics parametric analysis of the effect of fuselage drag and pitching moment on the Blade-Vortex Interaction (BVI) noise radiated by a medium lift helicopter (S-70UH-60) in a descending flight condition was conducted. The comprehensive analysis CAMRAD II was used for the calculation of vehicle trim, wake geometry and integrated air loads on the blade. The acoustics prediction code PSU-WOPWOP was used for calculating acoustic pressure signatures for a hemispherical grid centered at the hub. This paper revisits the concept of the X-force controller for BVI noise reduction, and investigates its effectiveness on an S-70 helicopter. The analysis showed that further BVI noise reductions were achievable by controlling the fuselage pitching moment. Reductions in excess of 6 dB of the peak BVI noise radiated towards the ground were demonstrated by compounding the effect of airframe drag and pitching moment simultaneously.

  16. [Methodology of the description of atmospheric air pollution by nitrogen dioxide by land use regression method in Ekaterinburg].

    Science.gov (United States)

    Antropov, K M; Varaksin, A N

    2013-01-01

    This paper provides the description of Land Use Regression (LUR) modeling and the result of its application in the study of nitrogen dioxide air pollution in Ekaterinburg. The paper describes the difficulties of the modeling for air pollution caused by motor vehicles exhaust, and the ways to address these challenges. To create LUR model of the NO2 air pollution in Ekaterinburg, concentrations of NO2 were measured, data on factors affecting air pollution were collected, a statistical analysis of the data were held. A statistical model of NO2 air pollution (coefficient of determination R2 = 0.70) and a map of pollution were created.

  17. Fundamentals of equine podiatry: balanced trimming and physiological shoeing

    OpenAIRE

    Estrada, Manuel

    2014-01-01

    The concepts of balanced trimming and physiological shoeing of the equine hoof as a way to prevent asymmetrical weight bearing and related orthopedic problems are discussed in this paper. Suggestions are given for the technical training of the personnel involved.  Considering the quantity and quality of the existing equine herd in Costa Rica, it is recommended to create a Farrier School as well as to coordinate the necessary efforts with other educational institutions related to the animal in...

  18. A Novel Performance Framework and Methodology to Analyze the Impact of 4D Trajectory Based Operations in the Future Air Traffic Management System

    OpenAIRE

    Ruiz, Sergio; Lopez Leones, Javier; Ranieri, Andrea

    2018-01-01

    The introduction of new Air Traffic Management (ATM) concepts such as Trajectory Based Operations (TBO) may produce a significant impact in all performance areas, that is, safety, capacity, flight efficiency, and others. The performance framework in use today has been tailored to the operational needs of the current ATM system and must evolve to fulfill the new needs and challenges brought by the TBO content. This paper presents a novel performance assessment framework and methodology adapted...

  19. TRIMS: Validating T2 Molecular Effects for Neutrino Mass Experiments

    Science.gov (United States)

    Lin, Ying-Ting; Trims Collaboration

    2017-09-01

    The Tritium Recoil-Ion Mass Spectrometer (TRIMS) experiment examines the branching ratio of the molecular tritium (T2) beta decay to the bound state (3HeT+). Measuring this branching ratio helps to validate the current molecular final-state theory applied in neutrino mass experiments such as KATRIN and Project 8. TRIMS consists of a magnet-guided time-of-flight mass spectrometer with a detector located on each end. By measuring the kinetic energy and time-of-flight difference of the ions and beta particles reaching the detectors, we will be able to distinguish molecular ions from atomic ones and hence derive the ratio in question. We will give an update on the apparatus, simulation software, and analysis tools, including efforts to improve the resolution of our detectors and to characterize the stability and uniformity of our field sources. We will also share our commissioning results and prospects for physics data. The TRIMS experiment is supported by U.S. Department of Energy Office of Science, Office of Nuclear Physics, Award Number DE-FG02-97ER41020.

  20. Practical demonstration of urban air quality simulation models. Part I. A report of the NATO/CCMS pilot study on air pollution assessment methodology and modeling

    Energy Technology Data Exchange (ETDEWEB)

    1980-08-01

    Report shows cooperation of NATO member nations in developing standardized methods for emissions data storage and retrieval to support requirements in conduct of national air quality management programs. Shows cooperation in developing standardized techniques for projecting emissions and predicting future ambient air quality.

  1. TRIM37 defective in mulibrey nanism is a novel RING finger ubiquitin E3 ligase

    International Nuclear Information System (INIS)

    Kallijaervi, Jukka; Lahtinen, Ulla; Haemaelaeinen, Riikka; Lipsanen-Nyman, Marita; Palvimo, Jorma J.; Lehesjoki, Anna-Elina

    2005-01-01

    Mulibrey nanism is an autosomal recessive prenatal-onset growth disorder characterized by dysmorphic features, cardiomyopathy, and hepatomegaly. Mutations in TRIM37 encoding a tripartite motif (TRIM, RING-B-box-coiled-coil)-family protein underlie mulibrey nanism. We investigated the ubiquitin ligase activity predicted for the RING domain of TRIM37 by analyzing its autoubiquitination. Full-length TRIM37 and its TRIM domain were highly polyubiquitinated when co-expressed with ubiquitin. Polyubiquitination was decreased in a mutant protein with disrupted RING domain (Cys35Ser;Cys36Ser) and in the Leu76Pro mutant protein, a disease-associated missense mutation affecting the TRIM domain of TRIM37. Bacterially produced GST-TRIM domain fusion protein, but not its Cys35Ser;Cys36Ser or Leu76Pro mutants, were polyubiquitinated in cell-free conditions, implying RING-dependent modification. Ubiquitin was also identified as an interaction partner for TRIM37 in a yeast two-hybrid screen. Ectopically expressed TRIM37 rapidly formed aggregates that were ubiquitin-, proteasome subunit-, and chaperone-positive in immunofluorescence analysis, defining them as aggresomes. The Cys35Ser;Cys36Ser mutant and the Leu76Pro and Gly322Val patient mutant proteins were markedly less prone to aggregation, implying that aggresomal targeting reflects a physiological function of TRIM37. These findings suggest that TRIM37 acts as a TRIM domain-dependent E3 ubiquitin ligase and imply defective ubiquitin-dependent degradation of an as-yet-unidentified target protein in the pathogenesis of mulibrey nanism

  2. Methodology to determine the appropriate amount of excess air for the operation of a gas turbine in a wet environment

    Energy Technology Data Exchange (ETDEWEB)

    Lugo-Leyte, R.; Zamora-Mata, J.M.; Torres-Aldaco, A. [Universidad Autonoma Metropolitana-Iztapalapa, Departamento de Ingenieria de Procesos e Hidraulica, San Rafael Atlixco 186, Col Vicentina 09340, Iztapalapa, Mexico, D.F. (Mexico); Toledo-Velazquez, M. [Instituto Politecnico Nacional, Escuela Superior de Ingenieria Mecanica y Electrica, Seccion de Estudios de Posgrado e Investigacion, Laboratorio de Ingenieria Termica e Hidraulica Aplicada, Unidad Profesional Adolfo Lopez Mateos, Edificio 5, 3er piso SEPI-ESIME, C.P. 07738, Col. Lindavista, Mexico D.F. (Mexico); Salazar-Pereyra, M. [Tecnologico de Estudios Superiores de Ecatepec, Division de Ingenieria Mecatronica e Industrial, Posgrado en Ciencias en Ingenieria Mecatronica, Av. Tecnologico s/n, Col. Valle de Anahuac, C.P. 55210, Ecatepec de Morelos, Estado de Mexico (Mexico)

    2010-02-15

    This paper addresses the impact of excess air on turbine inlet temperature, power, and thermal efficiency at different pressure ratios. An explicit relationship is developed to determine the turbine inlet temperature as a function of excess air, pressure ratio and relative humidity. The effect of humidity on the calculation of excess air to achieve a pre-established power output is analyzed and presented. Likewise it is demonstrated that dry air calculations provide a valid upper bound for the performance of a gas turbine under a wet environment. (author)

  3. Methodologies for estimating air emissions from three non-traditional source categories: Oil spills, petroleum vessel loading and unloading, and cooling towers. Final report, October 1991-March 1993

    International Nuclear Information System (INIS)

    Ramadan, W.; Sleva, S.; Dufner, K.; Snow, S.; Kersteter, S.L.

    1993-04-01

    The report discusses part of EPA's program to identify and characterize emissions sources not currently accounted for by either the existing Aerometric Information Retrieval System (AIRS) or State Implementation Plan (SIP) area source methodologies and to develop appropriate emissions estimation methodologies and emission factors for a group of these source categories. Based on the results of the identification and characterization portions of this research, three source categories were selected for methodology and emission factor development: oil spills, petroleum vessel loading and unloading, and cooling towers. The report describes the category selection process and presents emissions estimation methodologies and emission factor data for the selected source categories. The discussions for each category include general background information, emissions generation activities, pollutants emitted, sources of activity and pollutant data, emissions estimation methodologies and data issues. The information used in these discussions was derived from various sources including available literature, industrial and trade association publications and contracts, experts on the category and activity, and knowledgeable federal and state personnel

  4. Methodology for setup and data processing of mobile air quality measurements to assess the spatial variability of concentrations in urban environments

    International Nuclear Information System (INIS)

    Van Poppel, Martine; Peters, Jan; Bleux, Nico

    2013-01-01

    A case study is presented to illustrate a methodology for mobile monitoring in urban environments. A dataset of UFP, PM 2.5 and BC concentrations was collected. We showed that repeated mobile measurements could give insight in spatial variability of pollutants at different micro-environments in a city. Streets of contrasting traffic intensity showed increased concentrations by a factor 2–3 for UFP and BC and by 2.5 . The first quartile (P25) of the mobile measurements at an urban background zone seems to be good estimate of the urban background concentration. The local component of the pollutant concentrations was determined by background correction. The use of background correction reduced the number of runs needed to obtain representative results. The results presented, are a first attempt to establish a methodology for setup and data processing of mobile air quality measurements to assess the spatial variability of concentrations in urban environments. -- Highlights: ► Mobile measurements are used to assess the variability of air pollutants in urban environments. ► PM 2.5 , BC and UFP concentrations are presented for zones with different traffic characteristics. ► A methodology for background correction based on the mobile measurements is presented. ► The background concentration is estimated as the 25th percentile of the urban background data. ► The minimum numbers of runs for a representative estimate is reduced after background correction. -- This paper shows that the spatial variability of air pollutants in an urban environment can be assessed by a mobile monitoring methodology including background correction

  5. Structure and catalytic activation of the TRIM23 RING E3 ubiquitin ligase: DAWIDZIAK et al.

    Energy Technology Data Exchange (ETDEWEB)

    Dawidziak, Daria M. [Department of Molecular Physiology and Biological Physics, University of Virginia, Charlottesville Virginia; Sanchez, Jacint G. [Department of Molecular Physiology and Biological Physics, University of Virginia, Charlottesville Virginia; Wagner, Jonathan M. [Department of Molecular Physiology and Biological Physics, University of Virginia, Charlottesville Virginia; Ganser-Pornillos, Barbie K. [Department of Molecular Physiology and Biological Physics, University of Virginia, Charlottesville Virginia; Pornillos, Owen [Department of Molecular Physiology and Biological Physics, University of Virginia, Charlottesville Virginia

    2017-07-24

    Tripartite motif (TRIM) proteins comprise a large family of RING-type ubiquitin E3 ligases that regulate important biological processes. An emerging general model is that TRIMs form elongated antiparallel coiled-coil dimers that prevent interaction of the two attendant RING domains. The RING domains themselves bind E2 conjugating enzymes as dimers, implying that an active TRIM ligase requires higher-order oligomerization of the basal coiled-coil dimers. Here, we report crystal structures of the TRIM23 RING domain in isolation and in complex with an E2–ubiquitin conjugate. Our results indicate that TRIM23 enzymatic activity requires RING dimerization, consistent with the general model of TRIM activation.

  6. Methodologies of health impact assessment as part of an integrated approach to reduce effects of air pollution

    OpenAIRE

    Aunan, Kristin; Seip, Hans Martin

    1995-01-01

    Quantification of average frequencies of health effects on a population level is an essential part of an integrated assessment of pollution effects. Epidemiological studies seem to provide the best basis for such estimates. This paper gives an introduction to a methodology for health impact assessment. It also gives results from some selected parts of a case-study in Hungary. This study is aimed at testing and improving the methodology for integrated assessment and focuses on energy productio...

  7. Creating a Methodology for Coordinating High-resolution Air Quality Improvement Map and Greenhouse Gas Mitigation Strategies in Pittsburgh City

    Science.gov (United States)

    Shi, J.; Donahue, N. M.; Klima, K.; Blackhurst, M.

    2016-12-01

    In order to tradeoff global impacts of greenhouse gases with highly local impacts of conventional air pollution, researchers require a method to compare global and regional impacts. Unfortunately, we are not aware of a method that allows these to be compared, "apples-to-apples". In this research we propose a three-step model to compare possible city-wide actions to reduce greenhouse gases and conventional air pollutants. We focus on Pittsburgh, PA, a city with consistently poor air quality that is interested in reducing both greenhouse gases and conventional air pollutants. First, we use the 2013 Pittsburgh Greenhouse Gas Inventory to update the Blackhurst et al. model and conduct a greenhouse gas abatement potentials and implementation costs of proposed greenhouse gas reduction efforts. Second, we use field tests for PM2.5, NOx, SOx, organic carbon (OC) and elemental carbon (EC) data to inform a Land-use Regression Model for local air pollution at a 100m x 100m spatial level, which combined with a social cost of air pollution model (EASIUR) allows us to calculate economic social damages. Third, we combine these two models into a three-dimensional greenhouse gas cost abatement curve to understand the implementation costs and social benefits in terms of air quality improvement and greenhouse gas abatement for each potential intervention. We anticipated such results could provide policy-maker insights in green city development.

  8. A quality control method by ultrasonic vibration energy and diagnosis system at trimming process

    International Nuclear Information System (INIS)

    Suh, Chang Min; Song, Gil Ho; Pyoun, Young Shik

    2007-01-01

    In this paper, the characteristics in mechanical properties of ultrasonic cold forging treatment (UCFT) used for the trimming knife and the effects of ultrasonic vibration energy (UVE) into the trimming process on the state of the strip cutting face were studied. And a diagnosis system to quality control for trimming knife and strip cutting face was developed and installed in plant. By the plant application of UCFT, service life of knife was more increased over 100% than that of conventional knife and using the developed diagnosis system, the knife breakage and saw ear have been perfectly detected and quality control of trimming face is effectively obtained

  9. TRIM45 negatively regulates NF-κB-mediated transcription and suppresses cell proliferation

    International Nuclear Information System (INIS)

    Shibata, Mio; Sato, Tomonobu; Nukiwa, Ryota; Ariga, Tadashi; Hatakeyama, Shigetsugu

    2012-01-01

    Highlights: ► NF-κB plays an important role in cell survival and carcinogenesis. ► TRIM45 negatively regulates TNFα-induced NF-κB-mediated transcription. ► TRIM45 overexpression suppresses cell growth. ► TRIM45 acts as a repressor for the NF-κB signal and regulates cell growth. -- Abstract: The NF-κB signaling pathway plays an important role in cell survival, immunity, inflammation, carcinogenesis, and organogenesis. Activation of NF-κB is regulated by several posttranslational modifications including phosphorylation, neddylation and ubiquitination. The NF-κB signaling pathway is activated by two distinct signaling mechanisms and is strictly modulated by the ubiquitin–proteasome system. It has been reported that overexpression of TRIM45, one of the TRIM family ubiquitin ligases, suppresses transcriptional activities of Elk-1 and AP-1, which are targets of the MAPK signaling pathway. In this study, we showed that TRIM45 also negatively regulates TNFα-induced NF-κB-mediated transcription by a luciferase reporter assay and that TRIM45 lacking a RING domain also has an activity to inhibit the NF-κB signal. Moreover, we found that TRIM45 overexpression suppresses cell growth. These findings suggest that TRIM45 acts as a repressor for the NF-κB signal and regulates cell growth.

  10. Microstructural investigations of the trimmed edge of DP980 steel sheets

    Science.gov (United States)

    Bhattacharya, S.; Green, D. E.; Sohmshetty, R.; Alpas, A. T.

    2017-10-01

    In order to reduce vehicle weight while maintaining crashworthiness, advanced high strength steels (AHSSs), such as DP980, are extensively used for manufacturing automotive body components. During trimming operations, the high tensile strength of DP980 sheets tends to cause damage of the trim edge of D2 die inserts, which result in deterioration of the edge quality. The objective of this work is to study the damage microstructures at the trimmed edge of DP980 steel sheets as a function of the number of trimming cycles. A mechanical press equipped with AISI D2 tool steel inserts was used to continuously trim 1.4 mm thick sheets of DP980 at a rate of 30 strokes/min. Cross-sectional SEM images of the trimmed edges revealed that the sheared edge quality of the DP980 sheets decreased, indicated by an increase in the burr width, with an increase in the number of trims from 40,000 to 70,000. Plastic strains were estimated using the displacements of the martensite plates within plastic flow fields of ferrite. Site-specific cross-sectional TEM samples, excised from the trimmed edge using the in-situ `lift-out' technique by focused ion-beam (FIB)-milling, revealed cracking at the ferrite/martensite interfaces after 70,000 cycles indicating an increase in the depth of deformation zone possibly due to trimming with a chipped and blunted die edge.

  11. TRIM8 downregulation in glioma affects cell proliferation and it is associated with patients survival

    International Nuclear Information System (INIS)

    Micale, Lucia; Fusco, Carmela; Fontana, Andrea; Barbano, Raffaela; Augello, Bartolomeo; De Nittis, Pasquelena; Copetti, Massimiliano; Pellico, Maria Teresa; Mandriani, Barbara; Cocciadiferro, Dario; Parrella, Paola; Fazio, Vito Michele; Dimitri, Lucia Maria Cecilia; D’Angelo, Vincenzo; Novielli, Chiara; Larizza, Lidia; Daga, Antonio; Merla, Giuseppe

    2015-01-01

    Human gliomas are a heterogeneous group of primary malignant brain tumors whose molecular pathogenesis is not yet solved. In this regard, a major research effort has been directed at identifying novel specific glioma-associated genes. Here, we investigated the effect of TRIM8 gene in glioma. TRIM8 transcriptional level was profiled in our own glioma cases collection by qPCR and confirmed in the independent TCGA glioma cohort. The association between TRIM8 expression and Overall Survival and Progression-free Survival in TCGA cohort was determined by using uni-multivariable Cox regression analysis. The effect of TRIM8 on patient glioma cell proliferation was evaluated by performing MTT and clonogenic assays. The mechanisms causing the reduction of TRIM8 expression were explored by using qPCR and in vitro assays. We showed that TRIM8 expression correlates with unfavorable clinical outcome in glioma patients. We found that a restored TRIM8 expression induced a significant reduction of clonogenic potential in U87MG and patient’s glioblastoma cells. Finally we provide experimental evidences showing that miR-17 directly targets the 3′ UTR of TRIM8 and post-transcriptionally represses the expression of TRIM8. Our study provides evidences that TRIM8 may participate in the carcinogenesis and progression of glioma and that the transcriptional repression of TRIM8 might have potential value for predicting poor prognosis in glioma patients. The online version of this article (doi:10.1186/s12885-015-1449-9) contains supplementary material, which is available to authorized users

  12. SUMO-interacting motifs of human TRIM5α are important for antiviral activity.

    Directory of Open Access Journals (Sweden)

    Gloria Arriagada

    2011-04-01

    Full Text Available Human TRIM5α potently restricts particular strains of murine leukemia viruses (the so-called N-tropic strains but not others (the B- or NB-tropic strains during early stages of infection. We show that overexpression of SUMO-1 in human 293T cells, but not in mouse MDTF cells, profoundly blocks N-MLV infection. This block is dependent on the tropism of the incoming virus, as neither B-, NB-, nor the mutant R110E of N-MLV CA (a B-tropic switch are affected by SUMO-1 overexpression. The block occurred prior to reverse transcription and could be abrogated by large amounts of restricted virus. Knockdown of TRIM5α in 293T SUMO-1-overexpressing cells resulted in ablation of the SUMO-1 antiviral effects, and this loss of restriction could be restored by expression of a human TRIM5α shRNA-resistant plasmid. Amino acid sequence analysis of human TRIM5α revealed a consensus SUMO conjugation site at the N-terminus and three putative SUMO interacting motifs (SIMs in the B30.2 domain. Mutations of the TRIM5α consensus SUMO conjugation site did not affect the antiviral activity of TRIM5α in any of the cell types tested. Mutation of the SIM consensus sequences, however, abolished TRIM5α antiviral activity against N-MLV. Mutation of lysines at a potential site of SUMOylation in the CA region of the Gag gene reduced the SUMO-1 block and the TRIM5α restriction of N-MLV. Our data suggest a novel aspect of TRIM5α-mediated restriction, in which the presence of intact SIMs in TRIM5α, and also the SUMO conjugation of CA, are required for restriction. We propose that at least a portion of the antiviral activity of TRIM5α is mediated through the binding of its SIMs to SUMO-conjugated CA.

  13. The mutagenicity of indoor air particles in a residential pilot field study: Application and evaluation of new methodologies

    Science.gov (United States)

    Lewtas, Joellen; Goto, Sumio; Williams, Katherine; Chuang, Jane C.; Petersen, Bruce A.; Wilson, Nancy K.

    The mutagenicity of indoor air paniculate matter has been measured in a pilot field study of homes in Columbus, Ohio during the 1984 winter. The study was conducted in eight all natural-gas homes and two all electric homes. Paniculate matter and semi-volatile organic compounds were collected indoors using a medium volume sampler. A micro-forward mutation bioassay employing Salmonella typhimurium strain TM 677 was used to quantify the mutagenicity in solvent extracts of microgram quantities of indoor air particles. The mutagenicity was quantified in terms of both mutation frequency per mg of organic matter extracted and per cubic meter of air sampled. The combustion source variables explored in this study included woodburning in fireplaces and cigarette smoking. Homes in which cigarette smoking occurred had the highest concentrations of mutagenicity per cubic meter of air. The average indoor air mutagenicity per cubic meter was highly correlated with the number of cigarettes smoked. When the separate sampling periods in each room were compared, the mutagenicity in the kitchen samples was the most highly correlated with the number of cigarettes smoked.

  14. Effect of two trimming methods of dairy cattle on concrete or rubber-covered slatted floors

    NARCIS (Netherlands)

    Ouweltjes, W.; Holzhauer, M.; Tol, van der P.P.J.; Werf, van der J.T.N.

    2009-01-01

    This study monitored claw health, claw conformation, locomotion, activity, and step traits of cows from a single dairy herd that were trimmed according to the standard Dutch method or with an alternative "concave" trimming method. Half of the cows were kept in a stall section with concrete slatted

  15. Nuclear TRIM25 Specifically Targets Influenza Virus Ribonucleoproteins to Block the Onset of RNA Chain Elongation.

    Science.gov (United States)

    Meyerson, Nicholas R; Zhou, Ligang; Guo, Yusong R; Zhao, Chen; Tao, Yizhi J; Krug, Robert M; Sawyer, Sara L

    2017-11-08

    TRIM25 is an E3 ubiquitin ligase that activates RIG-I to promote the antiviral interferon response. The NS1 protein from all strains of influenza A virus binds TRIM25, although not all virus strains block the interferon response, suggesting alternative mechanisms for TRIM25 action. Here we present a nuclear role for TRIM25 in specifically restricting influenza A virus replication. TRIM25 inhibits viral RNA synthesis through a direct mechanism that is independent of its ubiquitin ligase activity and the interferon pathway. This activity can be inhibited by the viral NS1 protein. TRIM25 inhibition of viral RNA synthesis results from its binding to viral ribonucleoproteins (vRNPs), the structures containing individual viral RNA segments, the viral polymerase, and multiple viral nucleoproteins. TRIM25 binding does not inhibit initiation of capped-RNA-primed viral mRNA synthesis by the viral polymerase. Rather, the onset of RNA chain elongation is inhibited because TRIM25 prohibits the movement of RNA into the polymerase complex. Copyright © 2017 Elsevier Inc. All rights reserved.

  16. Genome-wide association study for claw disorders and trimming status in dairy cattle

    NARCIS (Netherlands)

    Spek, van der D.; Arendonk, van J.A.M.; Bovenhuis, H.

    2015-01-01

    Performing a genome-wide association study (GWAS) might add to a better understanding of the development of claw disorders and the need for trimming. Therefore, the aim of the current study was to perform a GWAS on claw disorders and trimming status and to validate the results for claw disorders

  17. Effect of Hardwood Sawmill Edging and Trimming Practices on Furniture Part Production

    Science.gov (United States)

    D. Earl Kline; Carmen Regalado; Eugene M. Wengert; Fred M. Lamb; Philip A. Araman

    1993-01-01

    In a recent edging and trimming study at three hardwood sawmills, it was observed that the lumber volume produced was approximately 10 percent less than would be necessary to make the most valuable lumber. Furthermore, the excess portion of wood that was removed from the edging and trimming process contained a large percentage of clear wood. In light of rising costs...

  18. Genetic parameters for claw disorders and the effect of preselecting cows for trimming.

    Science.gov (United States)

    van der Spek, D; van Arendonk, J A M; Vallée, A A A; Bovenhuis, H

    2013-09-01

    Claw disorders are important traits relevant to dairy cattle breeding from an economical and welfare point of view. Selection for reduced claw disorders can be based on hoof trimmer records. Typically, not all cows in a herd are trimmed. Our objectives were to estimate heritabilities and genetic correlations for claw disorders and investigate the effect of selecting cows for trimming. The data set contained 50,238 cows, of which 20,474 cows had at least one claw trimming record, with a total of 29,994 records. Six claw trimmers scored 14 different claw disorders: abscess (AB), corkscrew claw (CC), (inter-)digital dermatitis or heel erosion (DER), double sole (DS), hardship groove (HG), interdigital hyperplasia (IH), interdigital phlegmon (IP), sand crack (SC), super-foul (SF), sole hemorrhage (SH), sole injury (SI), sole ulcer (SU), white line separation (WLS), yellow discoloration of the sole (YD), and a combined claw disorder trait. Frequencies of the claw disorders for trimmed cows ranged from 0.1% (CC, YD, HG) to 23.8% (DER). More than half of the cows scored had at least one claw disorder. Heritability on the observed scale ranged from 0.02 (DS, SH) to 0.14 (IH) and on the underlying scale from 0.05 to 0.43 in trimmed cows. Genetic correlations between laminitis-related claw disorders were moderate to high, and the same was found for hygiene-related claw disorders. The effect of selecting cows for trimming was first investigated by including untrimmed cows in the analyses and assuming they were not affected by claw disorders. Heritabilities on the underlying scale showed only minor changes. Second, different subsets of the data were created based on the percentage of trimmed cows in the herd. Heritabilities for IH, DER, and SU tended to decrease when a higher percentage of cows in the herd were trimmed. Finally, a bivariate model with a claw disorder and the trait "trimming status" was used, but heritabilities were similar. Heritability for trimming status was

  19. Health-related external cost assessment in Europe: methodological developments from ExternE to the 2013 Clean Air Policy Package.

    Science.gov (United States)

    van der Kamp, Jonathan; Bachmann, Till M

    2015-03-03

    "Getting the prices right" through internalizing external costs is a guiding principle of environmental policy making, one recent example being the EU Clean Air Policy Package released at the end of 2013. It is supported by impact assessments, including monetary valuation of environmental and health damages. For over 20 years, related methodologies have been developed in Europe in the Externalities of Energy (ExternE) project series and follow-up activities. In this study, we aim at analyzing the main methodological developments over time from the 1990s until today with a focus on classical air pollution-induced human health damage costs. An up-to-date assessment including the latest European recommendations is also applied. Using a case from the energy sector, we identify major influencing parameters: differences in exposure modeling and related data lead to variations in damage costs of up to 21%; concerning risk assessment and monetary valuation, differences in assessing long-term exposure mortality risks together with assumptions on particle toxicity explain most of the observed changes in damage costs. These still debated influencing parameters deserve particular attention when damage costs are used to support environmental policy making.

  20. A multi-methodological approach to study the temporal and spatial distribution of air quality related to road transport emissions in Madrid, Spain

    Science.gov (United States)

    Perez, Pedro; Miranda, Regina

    2013-04-01

    emission inventory, together with the mobile source's parameters and the disaggregated transport activity data. The paper will also identify emission and concentration differences and gradients of certain magnitude/factor (e.g. comparison between estimated ATPs hourly concentrations in Madrid City Center and in the peripheries). Furthermore, because of the higher contribution of road mobile sources to GHGs and ATPs emissions in Madrid, small gradients between urban highways and residential areas will be expected. Second, the paper objectives are to develop valid methods and approaches to measure air quality and to develop valid road transport emission inventories to assess correlations between external costs, epidemiology and emissions in order to reveal how traffic pollution affects people exposure to key contaminants and disease development, and identify susceptible emission scenarios and health impacts. We have conducted general emission inventory studies providing preliminary evidence of regional road transport air pollution impacts on external cost growth and disease development. Third, we also aim to demonstrate short and long-term impacts of road transport emissions on external costs development using innovative multi-methodological methods interfaced with environmental chemistry and meteorology following meteorological and chemical fields with contrasting high/low traffic emissions in several linked components involving: air pollutant assessment using local measurements, height of the boundary layer, meteorological environment interactions on external costs and epidemiology, mapping of Madrid (identifying gradients of emissions), integrative causal modeling using statistical models, and trend and scenario analyses on external costs and impacts on human health. Meteorological and chemical fields will be obtained from local records collected by surface meteorological and air quality stations. These two sets of fields define the horizontal and vertical profiles of

  1. TRIM15 is a focal adhesion protein that regulates focal adhesion disassembly

    Science.gov (United States)

    Uchil, Pradeep D.; Pawliczek, Tobias; Reynolds, Tracy D.; Ding, Siyuan; Hinz, Angelika; Munro, James B.; Huang, Fang; Floyd, Robert W.; Yang, Haitao; Hamilton, William L.; Bewersdorf, Joerg; Xiong, Yong; Calderwood, David A.; Mothes, Walther

    2014-01-01

    ABSTRACT Focal adhesions are macromolecular complexes that connect the actin cytoskeleton to the extracellular matrix. Dynamic turnover of focal adhesions is crucial for cell migration. Paxillin is a multi-adaptor protein that plays an important role in regulating focal adhesion dynamics. Here, we identify TRIM15, a member of the tripartite motif protein family, as a paxillin-interacting factor and a component of focal adhesions. TRIM15 localizes to focal contacts in a myosin-II-independent manner by an interaction between its coiled-coil domain and the LD2 motif of paxillin. Unlike other focal adhesion proteins, TRIM15 is a stable focal adhesion component with restricted mobility due to its ability to form oligomers. TRIM15-depleted cells display impaired cell migration and reduced focal adhesion disassembly rates, in addition to enlarged focal adhesions. Thus, our studies demonstrate a cellular function for TRIM15 as a regulatory component of focal adhesion turnover and cell migration. PMID:25015296

  2. Air

    International Nuclear Information System (INIS)

    Gugele, B.; Scheider, J.; Spangl, W.

    2001-01-01

    In recent years several regulations and standards for air quality and limits for air pollution were issued or are in preparation by the European Union, which have severe influence on the environmental monitoring and legislation in Austria. This chapter of the environmental control report of Austria gives an overview about the legal situation of air pollution control in the European Union and in specific the legal situation in Austria. It gives a comprehensive inventory of air pollution measurements for the whole area of Austria of total suspended particulates, ozone, volatile organic compounds, nitrogen oxides, sulfur dioxide, carbon monoxide, heavy metals, benzene, dioxin, polycyclic aromatic hydrocarbons and eutrophication. For each of these pollutants the measured emission values throughout Austria are given in tables and geographical charts, the environmental impact is discussed, statistical data and time series of the emission sources are given and legal regulations and measures for an effective environmental pollution control are discussed. In particular the impact of fossil-fuel power plants on the air pollution is analyzed. (a.n.)

  3. Trimming of mammalian transcriptional networks using network component analysis

    Directory of Open Access Journals (Sweden)

    Liao James C

    2010-10-01

    Full Text Available Abstract Background Network Component Analysis (NCA has been used to deduce the activities of transcription factors (TFs from gene expression data and the TF-gene binding relationship. However, the TF-gene interaction varies in different environmental conditions and tissues, but such information is rarely available and cannot be predicted simply by motif analysis. Thus, it is beneficial to identify key TF-gene interactions under the experimental condition based on transcriptome data. Such information would be useful in identifying key regulatory pathways and gene markers of TFs in further studies. Results We developed an algorithm to trim network connectivity such that the important regulatory interactions between the TFs and the genes were retained and the regulatory signals were deduced. Theoretical studies demonstrated that the regulatory signals were accurately reconstructed even in the case where only three independent transcriptome datasets were available. At least 80% of the main target genes were correctly predicted in the extreme condition of high noise level and small number of datasets. Our algorithm was tested with transcriptome data taken from mice under rapamycin treatment. The initial network topology from the literature contains 70 TFs, 778 genes, and 1423 edges between the TFs and genes. Our method retained 1074 edges (i.e. 75% of the original edge number and identified 17 TFs as being significantly perturbed under the experimental condition. Twelve of these TFs are involved in MAPK signaling or myeloid leukemia pathways defined in the KEGG database, or are known to physically interact with each other. Additionally, four of these TFs, which are Hif1a, Cebpb, Nfkb1, and Atf1, are known targets of rapamycin. Furthermore, the trimmed network was able to predict Eno1 as an important target of Hif1a; this key interaction could not be detected without trimming the regulatory network. Conclusions The advantage of our new algorithm

  4. Potential role of TRIM3 as a novel tumour suppressor in colorectal cancer (CRC) development.

    Science.gov (United States)

    Piao, Mei-Yu; Cao, Hai-Long; He, Na-Na; Xu, Meng-Que; Dong, Wen-Xiao; Wang, Wei-Qiang; Wang, Bang-Mao; Zhou, Bing

    2016-01-01

    Colorectal cancer (CRC) is the third leading cause of cancer-related mortality in the United States. Recent cancer genome-sequencing efforts and complementary functional studies have led to the identification of a collection of candidate 'driver' genes involved in CRC tumorigenesis. Tripartite motif (TRIM3) is recently identified as a tumour suppressor in glioblastoma but this tumour-suppressive function has not been investigated in CRC. In this study, we investigated the potential role of TRIM3 as a tumour suppressor in CRC development by manipulating the expression of TRIM3 in two authentic CRC cell lines, HCT116 and DLD1, followed by various functional assays, including cell proliferation, colony formation, scratch wound healing, soft agar, and invasion assays. Xenograft experiment was performed to examine in vivo tumour-suppressive properties of TRIM3. Small-interfering RNA (siRNA) mediated knockdown of TRIM3 conferred growth advantage in CRC cells. In contrast, overexpression of TRIM3 affected cell survival, cell migration, anchorage independent growth and invasive potential in CRC cells. In addition, TRIM3 was found to be down-regulated in human colon cancer tissues compared with matched normal colon tissues. Overexpression of TRIM3 significantly inhibited tumour growth in vivo using xenograft mouse models. Mechanistic investigation revealed that TRIM3 can regulate p53 protein level through its stabilisation. TRIM3 functions as a tumour suppressor in CRC progression. This tumour-suppressive function is exerted partially through regulation of p53 protein. Therefore, this protein may represent a novel therapeutic target for prevention or intervention of CRC.

  5. The Air Force Manufacturing Technology (MANTECH): Technology transfer methodology as exemplified by the radar transmit/receive module program

    Science.gov (United States)

    Houpt, Tracy; Ridgely, Margaret

    1991-01-01

    The Air Force Manufacturing Technology program is involved with the improvement of radar transmit/receive modules for use in active phased array radars for advanced fighter aircraft. Improvements in all areas of manufacture and test of these modules resulting in order of magnitude improvements in the cost of and the rate of production are addressed, as well as the ongoing transfer of this technology to the Navy.

  6. 77 FR 67399 - Trim Systems Operating Corp., a Subsidiary of Commercial Vehicle Group, Inc., Including On-Site...

    Science.gov (United States)

    2012-11-09

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-81,393] Trim Systems Operating..., applicable to workers and former workers of Trim Systems Operating Corp., a subsidiary of Commercial Vehicle.... The amended notice applicable to TA-W-81,393 is hereby issued as follows: All workers of Trim Systems...

  7. Efficient running of steam generator trims fuel cost

    International Nuclear Information System (INIS)

    Selim, M.; Eltouny, S.A.

    1993-01-01

    E scaling energy prices have led to drastic changes in the operating philosophy of the worldwide industry. About 50% of the thermal energy in industry is being consumed in steam boilers. The new energy reduction programs that have been adopted in egypt draw attention to the boilers, not only to trim energy consumption and improve the production of steam but also to save as much money as possible in doing it. Organization for energy planning (OEP) has started a program for 'Boiler efficiency improvement' in industry since 2 years. The program aimed at performing energy audits in a selective number of industries in both public and private sectors using fire tube boilers produced locally by El Nasr company. As a result of audits an evaluation of performance of this type of boilers was,performed. The energy profiles and the common problems affecting the efficiency of boilers were determined. Energy conservation opportunities (ECO) were identified. 9 figs

  8. High resolution micro ultrasonic machining for trimming 3D microstructures

    International Nuclear Information System (INIS)

    Viswanath, Anupam; Li, Tao; Gianchandani, Yogesh

    2014-01-01

    This paper reports on the evaluation of a high resolution micro ultrasonic machining (HR-µUSM) process suitable for post fabrication trimming of complex 3D microstructures made from fused silica. Unlike conventional USM, the HR-µUSM process aims for low machining rates, providing high resolution and high surface quality. The machining rate is reduced by keeping the micro-tool tip at a fixed distance from the workpiece and vibrating it at a small amplitude. The surface roughness is improved by an appropriate selection of abrasive particles. Fluidic modeling is performed to study interaction among the vibrating micro-tool tip, workpiece, and the slurry. Using 304 stainless steel (SS304) tool tips of 50 µm diameter, the machining performance of the HR-µUSM process is characterized on flat fused silica substrates. The depths and surface finish of machined features are evaluated as functions of slurry concentrations, separation between the micro-tool and workpiece, and machining time. Under the selected conditions, the HR-µUSM process achieves machining rates as low as 10 nm s −1  averaged over the first minute of machining of a flat virgin sample. This corresponds to a mass removal rate of ≈20 ng min −1 . The average surface roughness, S a , achieved is as low as 30 nm. Analytical and numerical modeling are used to explain the typical profile of the machined features as well as machining rates. The process is used to demonstrate trimming of hemispherical 3D shells made of fused silica. (paper)

  9. Identification of TRIM27 as a novel degradation target of herpes simplex virus 1 ICP0.

    Science.gov (United States)

    Conwell, Sara E; White, Anne E; Harper, J Wade; Knipe, David M

    2015-01-01

    The herpes simplex virus 1 (HSV-1) immediate early protein ICP0 performs many functions during infection, including transactivation of viral gene expression, suppression of innate immune responses, and modification and eviction of histones from viral chromatin. Although these functions of ICP0 have been characterized, the detailed mechanisms underlying ICP0's complex role during infection warrant further investigation. We thus undertook an unbiased proteomic approach to identifying viral and cellular proteins that interact with ICP0 in the infected cell. Cellular candidates resulting from our analysis included the ubiquitin-specific protease USP7, the transcriptional repressor TRIM27, DNA repair proteins NBN and MRE11A, regulators of apoptosis, including BIRC6, and the proteasome. We also identified two HSV-1 early proteins involved in nucleotide metabolism, UL39 and UL50, as novel candidate interactors of ICP0. Because TRIM27 was the most statistically significant cellular candidate, we investigated the relationship between TRIM27 and ICP0. We observed rapid, ICP0-dependent loss of TRIM27 during HSV-1 infection. TRIM27 protein levels were restored by disrupting the RING domain of ICP0 or by inhibiting the proteasome, arguing that TRIM27 is a novel degradation target of ICP0. A mutant ICP0 lacking E3 ligase activity interacted with endogenous TRIM27 during infection as demonstrated by reciprocal coimmunoprecipitation and supported by immunofluorescence data. Surprisingly, ICP0-null mutant virus yields decreased upon TRIM27 depletion, arguing that TRIM27 has a positive effect on infection despite being targeted for degradation. These results illustrate a complex interaction between TRIM27 and viral infection with potential positive or negative effects of TRIM27 on HSV under different infection conditions. During productive infection, a virus must simultaneously redirect multiple cellular pathways to replicate itself while evading detection by the host's defenses. To

  10. General Model for Retroviral Capsid Pattern Recognition by TRIM5 Proteins.

    Science.gov (United States)

    Wagner, Jonathan M; Christensen, Devin E; Bhattacharya, Akash; Dawidziak, Daria M; Roganowicz, Marcin D; Wan, Yueping; Pumroy, Ruth A; Demeler, Borries; Ivanov, Dmitri N; Ganser-Pornillos, Barbie K; Sundquist, Wesley I; Pornillos, Owen

    2018-02-15

    Restriction factors are intrinsic cellular defense proteins that have evolved to block microbial infections. Retroviruses such as HIV-1 are restricted by TRIM5 proteins, which recognize the viral capsid shell that surrounds, organizes, and protects the viral genome. TRIM5α uses a SPRY domain to bind capsids with low intrinsic affinity ( K D of >1 mM) and therefore requires higher-order assembly into a hexagonal lattice to generate sufficient avidity for productive capsid recognition. TRIMCyp, on the other hand, binds HIV-1 capsids through a cyclophilin A domain, which has a well-defined binding site and higher affinity ( K D of ∼10 μM) for isolated capsid subunits. Therefore, it has been argued that TRIMCyp proteins have dispensed with the need for higher-order assembly to function as antiviral factors. Here, we show that, consistent with its high degree of sequence similarity with TRIM5α, the TRIMCyp B-box 2 domain shares the same ability to self-associate and facilitate assembly of a TRIMCyp hexagonal lattice that can wrap about the HIV-1 capsid. We also show that under stringent experimental conditions, TRIMCyp-mediated restriction of HIV-1 is indeed dependent on higher-order assembly. Both forms of TRIM5 therefore use the same mechanism of avidity-driven capsid pattern recognition. IMPORTANCE Rhesus macaques and owl monkeys are highly resistant to HIV-1 infection due to the activity of TRIM5 restriction factors. The rhesus macaque TRIM5α protein blocks HIV-1 through a mechanism that requires self-assembly of a hexagonal TRIM5α lattice around the invading viral core. Lattice assembly amplifies very weak interactions between the TRIM5α SPRY domain and the HIV-1 capsid. Assembly also promotes dimerization of the TRIM5α RING E3 ligase domain, resulting in synthesis of polyubiquitin chains that mediate downstream steps of restriction. In contrast to rhesus TRIM5α, the owl monkey TRIM5 homolog, TRIMCyp, binds isolated HIV-1 CA subunits much more tightly

  11. Genetic evaluation of claw health traits accounting for potential preselection of cows to be trimmed.

    Science.gov (United States)

    Croué, Iola; Fikse, Freddy; Johansson, Kjell; Carlén, Emma; Thomas, Gilles; Leclerc, Hélène; Ducrocq, Vincent

    2017-10-01

    Claw lesions are one of the most important health issues in dairy cattle. Although the frequency of claw lesions depends greatly on herd management, the frequency can be lowered through genetic selection. A genetic evaluation could be developed based on trimming records collected by claw trimmers; however, not all cows present in a herd are usually selected by the breeder to be trimmed. The objectives of this study were to investigate the importance of the preselection of cows for trimming, to account for this preselection, and to estimate genetic parameters of claw health traits. The final data set contained 25,511 trimming records of French Holstein cows. Analyzed claw lesion traits were digital dermatitis, heel horn erosion, interdigital hyperplasia, sole hemorrhage circumscribed, sole hemorrhage diffused, sole ulcer, and white line fissure. All traits were analyzed as binary traits in a multitrait linear animal model. Three scenarios were considered: including only trimmed cows in a 7-trait model (scenario 1); or trimmed cows and contemporary cows not trimmed but present at the time of a visit (considering that nontrimmed cows were healthy) in a 7-trait model (scenario 2); or trimmed cows and contemporary cows not trimmed but present at the time of a visit (considering lesion records for trimmed cows only), in an 8-trait model, including a 0/1 trimming status trait (scenario 3). For scenario 3, heritability estimates ranged from 0.02 to 0.09 on the observed scale. Genetic correlations clearly revealed 2 groups of traits (digital dermatitis, heel horn erosion, and interdigital hyperplasia on the one hand, and sole hemorrhage circumscribed, sole hemorrhage diffused, sole ulcer, and white line fissure on the other hand). Heritabilities on the underlying scale did not vary much depending on the scenario: the effect of the preselection of cows for trimming on the estimation of heritabilities appeared to be negligible. However, including untrimmed cows as healthy

  12. Cyclophilin A potentiates TRIM5α inhibition of HIV-1 nuclear import without promoting TRIM5α binding to the viral capsid.

    Directory of Open Access Journals (Sweden)

    Mallori Burse

    Full Text Available The host immunophilin cyclophilin A (CypA binds to the capsid protein (CA of HIV-1 and regulates its infectivity. Depending on the target cell type, CypA can either promote or inhibit HIV-1 infection. The ability of CypA to promote HIV-1 infection has been extensively studied and linked to several steps in early replication including uncoating, reverse transcription and nuclear import. By contrast, the mechanism by which CypA inhibits infection is less well understood. We investigated the mechanism by which CypA potentiates restriction of HIV-1 by the tripartite motif-containing protein 5 (TRIM5α. Depletion of TRIM5α in the African green monkey cell line Vero, resulted in a loss of inhibition of infection by CypA, demonstrating that inhibition by CypA is mediated by TRIM5α. Complementary genetic and biochemical assays failed to demonstrate an ability of CypA to promote binding of TRIM5α to the viral capsid. TRIM5α inhibits HIV-1 reverse transcription in a proteasome-dependent manner; however, we observed that inhibition of proteasome activity did not reduce the ability of CypA to inhibit infection, suggesting that CypA acts at a step after reverse transcription. Accordingly, we observed a CypA-dependent reduction in the accumulation of nuclear HIV-1 DNA, indicating that CypA specifically promotes TRIM5α inhibition of HIV-1 nuclear import. We also observed that the ability of CypA to inhibit HIV-1 infection is abolished by amino acid substitutions within the conserved CPSF6-binding surface in CA. Our results indicate that CypA inhibits HIV-1 infection in Vero cells not by promoting TRIM5α binding to the capsid but by blocking nuclear import of the HIV-1 preintegration complex.

  13. Effects of high voltage pulse trimming on structural properties of thick-film resistors

    Directory of Open Access Journals (Sweden)

    Stanimirović Zdravko

    2017-01-01

    Full Text Available Nowadays, compact and reliable electronic devices including up-to-date ceramic micro-electro-mechanical systems require thick-film resistors with significantly reduced dimensions and stable and precise resistance values. For that reason, instead of standard laser trimming method, high voltage pulse trimming of thick-film resistors is being introduced. This method allows controlled and reliable resistance adjustment regardless of resistor position or dimensions and without the presence of cuts. However, it causes irreversible structural changes in the pseudorandom network formed during sintering causing the changes in conducting mechanisms. In this paper results of the experimental investigation of high voltage pulse trimming of thick-film resistors are presented. Obtained results are analyzed and correlations between resistance and low-frequency noise changes and changes in conducting mechanisms in resistors due to high voltage pulse trimming are observed. Sources of measured fluctuations are identified and it is shown that this type of trimming is a valid alternative trimming method to the dominant laser trimming. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. III44003 and III45007

  14. TRIM32 ubiquitin E3 ligase, one enzyme for several pathologies: From muscular dystrophy to tumours.

    Science.gov (United States)

    Lazzari, Elisa; Meroni, Germana

    2016-10-01

    TRIM32 is a member of the TRIpartite Motif family characterised by the presence of an N-terminal three-domain-module that includes a RING domain, which confers E3 ubiquitin ligase activity, one or two B-box domains and a Coiled-Coil region that mediates oligomerisation. Several TRIM32 substrates were identified including muscular proteins and proteins involved in cell cycle regulation and cell motility. As ubiquitination is a versatile post-translational modification that can affect target turnover, sub-cellular localisation or activity, it is likely that diverse substrates may be differentially affected by TRIM32-mediated ubiquitination, reflecting its multi-faceted roles in muscle physiology, cancer and immunity. With particular relevance for muscle physiology, mutations in TRIM32 are associated with autosomal recessive Limb-Girdle Muscular Dystrophy 2H, a muscle-wasting disease with variable clinical spectrum ranging from almost asymptomatic to wheelchair-bound patients. In this review, we will focus on the ability of TRIM32 to mark specific substrates for proteasomal degradation discussing how the TRIM32-proteasome axis may (i) be important for muscle homeostasis and for the pathogenesis of muscular dystrophy; and (ii) define either an oncogenic or tumour suppressive role for TRIM32 in the context of different types of cancer. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. The effect of Trim5 polymorphisms on the clinical course of HIV-1 infection.

    Directory of Open Access Journals (Sweden)

    Daniëlle van Manen

    2008-02-01

    Full Text Available The antiviral factor tripartite interaction motif 5alpha (Trim5alpha restricts a broad range of retroviruses in a species-specific manner. Although human Trim5alpha is unable to block HIV-1 infection in human cells, a modest inhibition of HIV-1 replication has been reported. Recently two polymorphisms in the Trim5 gene (H43Y and R136Q were shown to affect the antiviral activity of Trim5alpha in vitro. In this study, participants of the Amsterdam Cohort studies were screened for polymorphisms at amino acid residue 43 and 136 of the Trim5 gene, and the potential effects of these polymorphisms on the clinical course of HIV-1 infection were analyzed. In agreement with the reported decreased antiviral activity of Trim5alpha that contains a Y at amino acid residue 43 in vitro, an accelerated disease progression was observed for individuals who were homozygous for the 43Y genotype as compared to individuals who were heterozygous or homozygous for the 43H genotype. A protective effect of the 136Q genotype was observed but only after the emergence of CXCR4-using (X4 HIV-1 variants and when a viral load of 10(4.5 copies per ml plasma was used as an endpoint in survival analysis. Interestingly, naive CD4 T cells, which are selectively targeted by X4 HIV-1, revealed a significantly higher expression of Trim5alpha than memory CD4 T cells. In addition, we observed that the 136Q allele in combination with the -2GG genotype in the 5'UTR was associated with an accelerated disease progression. Thus, polymorphisms in the Trim5 gene may influence the clinical course of HIV-1 infection also underscoring the antiviral effect of Trim5alpha on HIV-1 in vivo.

  16. The Effect of Trim5 Polymorphisms on the Clinical Course of HIV-1 Infection

    Science.gov (United States)

    van Manen, Daniëlle; Rits, Maarten A. N; Beugeling, Corrine; van Dort, Karel; Schuitemaker, Hanneke; Kootstra, Neeltje A

    2008-01-01

    The antiviral factor tripartite interaction motif 5α (Trim5α) restricts a broad range of retroviruses in a species-specific manner. Although human Trim5α is unable to block HIV-1 infection in human cells, a modest inhibition of HIV-1 replication has been reported. Recently two polymorphisms in the Trim5 gene (H43Y and R136Q) were shown to affect the antiviral activity of Trim5α in vitro. In this study, participants of the Amsterdam Cohort studies were screened for polymorphisms at amino acid residue 43 and 136 of the Trim5 gene, and the potential effects of these polymorphisms on the clinical course of HIV-1 infection were analyzed. In agreement with the reported decreased antiviral activity of Trim5α that contains a Y at amino acid residue 43 in vitro, an accelerated disease progression was observed for individuals who were homozygous for the 43Y genotype as compared to individuals who were heterozygous or homozygous for the 43H genotype. A protective effect of the 136Q genotype was observed but only after the emergence of CXCR4-using (X4) HIV-1 variants and when a viral load of 104.5 copies per ml plasma was used as an endpoint in survival analysis. Interestingly, naive CD4 T cells, which are selectively targeted by X4 HIV-1, revealed a significantly higher expression of Trim5α than memory CD4 T cells. In addition, we observed that the 136Q allele in combination with the −2GG genotype in the 5′UTR was associated with an accelerated disease progression. Thus, polymorphisms in the Trim5 gene may influence the clinical course of HIV-1 infection also underscoring the antiviral effect of Trim5α on HIV-1 in vivo. PMID:18248091

  17. Characterization and biological function analysis of the TRIM47 gene from common carp (Cyprinus carpio).

    Science.gov (United States)

    Wang, Yeda; Kuang, Ming; Lu, Yuanan; Lin, Li; Liu, Xueqin

    2017-09-05

    The TRIM family protein was known to play an important role in many cellular processes, including potential antiviral activity, which has attracted lots of attention. In this study, a TRIM47 homolog from common carp (Cyprinus carpio) was cloned and the full length coding DNA sequence (CDS) of this gene was analyzed, results showed that there was a 97% similarity between common carp and zebrafish (Danio rerio), but only 18% similarity with that of human (Homo sapiens) and mouse (Mus musculus). The tissue distribution analysis showed TRIM47 had the highest mRNA level in the brain, a few immune related organs such as liver and kidney also had a relatively high level of TRIM47 expression. SVCV infection decreased TRIM47 mRNA level significantly both in vitro and in vivo, but its expression was not affected by the virus at the protein level. The recombinant plasmid pcDNA4-TRIM47-His was constructed, the subcellular localization in FHM cells showed that TRIM47 uniformly distributed in the cytoplasm at the form of tiny spots, and partially localized in the mitochondria. Overexpression TRIM47 in FHM cells significantly decreased the mRNA level of SVCV-G gene, and it was accompanied with the increasing of IFN1, a member of type I IFN, at the case of SVCV stimulation. In summary, our results had first demonstrated that TRIM47 of the common carp played an important role in viral resistance processes as well as the regulation of IFN signaling pathway. Copyright © 2017. Published by Elsevier B.V.

  18. Development of methodology for detection of long lived alpha emitters in air based on simultaneous alpha and beta activity measurement

    International Nuclear Information System (INIS)

    Kaushik, Vivek; Rath, D.P.; Vinayagami, Bhakti; Ashokkumar, P.; Umashankar, C.; Gopalakrishnan, R.K.; Kulkarni, M.S.

    2018-01-01

    Interference of the radon and thoron progeny co-deposited on the filtration media is the long-standing problem related to prompt analyses in continuous air sampling or monitoring of any potential suspect radionuclides. The solutions to this problem have been quite diverse, and included, for example, simple gross-alpha counting, the use of beta-to-alpha ratios, and the use of alpha spectrum analyses. The techniques based on beta to alpha disintegration ratios make use of the naturally occurring alpha to beta disintegration ratios and departures therefrom. This ratio is found empirically to be relatively constant. With the help of the solution of differential equation, which govern the deposition of radionuclide on filter paper, one can easily estimate theoretically the behavior of the radon progeny alpha to beta disintegration (or count) rate ratio

  19. Guidelines for the use of biological monitors in air pollution control (plants). Pt. 1. Methodological guidance for the drawing-up of biomonitoring guidelines (plants)

    Energy Technology Data Exchange (ETDEWEB)

    Zimmermann, R.D. [Buero fuer Konzeptionelle Bioindikation, Jockgrim (Germany); Wagner, G. [Universitaet des Saarlandes, Saarbruecken (Germany). Inst. fuer Biogeographie; Finck, M.

    2000-04-01

    The main objective of this study is to encourage and promote further development of the methodological basis for a broader and more effective use of biological methods for monitoring the effects of air pollution on plants. It is not intended here to explain or discuss general criteria for the design of environmental monitoring studies and principal statistical methods for dealing with heterogeneously distributed spatial phenomena in detail. A further objective of this study is to give general guidance on how to - select suitable bioindicators, - develop, optimise and validate specific guidelines for the use of these bioindicators, - plan, design and employ biomonitoring studies for different purposes, - develop case-specific study plans determining how to apply an appropriate bioindicator (method-specific guideline) to a given task, case and area, - adapt principles of quality assurance and quality control to biomonitoring studies, - increase the importance and reliability of results obtained by bioindicators with respect to administrative measures. (orig.)

  20. Development of the SSC [Superconducting Super Collider] trim coil beam tube assembly

    International Nuclear Information System (INIS)

    Skaritka, J.; Kelly, E.; Schneider, W.

    1987-01-01

    The Superconducting Super Collider uses ≅9600 dipole magnets. The magnets have been carefully designed to exhibit minimal magnetic field harmonics. However, because of superconductor magnetization effects, iron saturation and conductor/coil positioning errors, certain harmonic errors are possible and must be corrected by use of multipole correctors called trim coils. For the most efficient use of axial space in the magnet, and lowest possible current, a distributed internal correction coil design is planned. The trim coil assembly is secured to the beam tube, a uhv tube with special strength, size, conductivity and vacuum. The report details the SSC trim coil/beam tube assembly specifications, history, and ongoing development

  1. From 1962 the teaching of Methodology of Radioisotopes is continuous in the University of Buenos Aires of the Argentine Republic; Desde 1962 la ensenanza de Metodologia de Radioisotopos es continua en la Universidad de Buenos Aires de la Republica Argentina

    Energy Technology Data Exchange (ETDEWEB)

    Rivera, E; Cremaschi, G; Martin, G; Zubillaga, M; Cricco, G; Davio, C; Genaro, A; Bianchin, A; Mohamad, N; Klecha, A; Calmanovici, G; Goldman, G; Salgueiro, J; Nunez, M; Medina, V; Gutierrez, A; Leonardi, N; Bergoc, R [Laboratorio de Radioisotopos, Facultad de Farmacia y Bioquimica, Universidad de Buenos Aires, Junin 956, 1113- Buenos Aires (Argentina)

    2006-07-01

    In the Faculty of Pharmacy and Biochemistry of the University of Buenos Aires the teaching of the radioisotopes began in 1960 and uninterruptedly continuous. The application of the radioisotopes and the radiations in different professional activities it is acceptable only in a context of radiological safety and with personal appropriately trained. Conscious of it, the training in grade, postgraduate and technicature, has more of 40% of the thematic one guided to the formation in radiological protection. The courses dictated at the moment in the Laboratory of Radioisotopes they include: Grade formation: to) Subject grade 'Methodology of Radioisotopes' in the Career of Biochemistry: it began to be dictated in 1960 and until the present, more of 6500 students they have gone by our classrooms. b) Grade subject 'Radiopharmacy' in the Career of Pharmacy: guided to the formation of a modern pharmacist, with necessary knowledge to be developed as professional in the Radiopharmaceutical area. Postgraduate formation: c) Postgraduate course of Methodology of Radioisotopes specially directed to biochemical, biologists, veterinarians, chemical. It is dictated uninterruptedly from 1962. d) Postgraduate course in Methodology of Radioisotopes for medical professionals, specially directed to professionals of the medicine that want to specialize in different branches of the Nuclear Medicine. Both courses have 220 present hours and it stops their approval the assistants they should surrender a final exam at open book that consists on the resolution of a practical exercise adapted to their professional practices. Until the present they have surrendered their exams satisfactorily approximately 2000 professionals coming from different areas of the Argentina and of several countries of Hispanic speech. e) Starting from 1992 the Course of Upgrade in Methodology of Radioisotopes directed to professionals that want to upgrade its knowledge in new radioisotopic methodologies is dictated

  2. From 1962 the teaching of Methodology of Radioisotopes is continuous in the University of Buenos Aires of the Argentine Republic; Desde 1962 la ensenanza de Metodologia de Radioisotopos es continua en la Universidad de Buenos Aires de la Republica Argentina

    Energy Technology Data Exchange (ETDEWEB)

    Rivera, E.; Cremaschi, G.; Martin, G.; Zubillaga, M.; Cricco, G.; Davio, C.; Genaro, A.; Bianchin, A.; Mohamad, N.; Klecha, A.; Calmanovici, G.; Goldman, G.; Salgueiro, J.; Nunez, M.; Medina, V.; Gutierrez, A.; Leonardi, N.; Bergoc, R. [Laboratorio de Radioisotopos, Facultad de Farmacia y Bioquimica, Universidad de Buenos Aires, Junin 956, 1113- Buenos Aires (Argentina)]. e-mail: rmbergoc@arnet.com.ar

    2006-07-01

    In the Faculty of Pharmacy and Biochemistry of the University of Buenos Aires the teaching of the radioisotopes began in 1960 and uninterruptedly continuous. The application of the radioisotopes and the radiations in different professional activities it is acceptable only in a context of radiological safety and with personal appropriately trained. Conscious of it, the training in grade, postgraduate and technicature, has more of 40% of the thematic one guided to the formation in radiological protection. The courses dictated at the moment in the Laboratory of Radioisotopes they include: Grade formation: to) Subject grade 'Methodology of Radioisotopes' in the Career of Biochemistry: it began to be dictated in 1960 and until the present, more of 6500 students they have gone by our classrooms. b) Grade subject 'Radiopharmacy' in the Career of Pharmacy: guided to the formation of a modern pharmacist, with necessary knowledge to be developed as professional in the Radiopharmaceutical area. Postgraduate formation: c) Postgraduate course of Methodology of Radioisotopes specially directed to biochemical, biologists, veterinarians, chemical. It is dictated uninterruptedly from 1962. d) Postgraduate course in Methodology of Radioisotopes for medical professionals, specially directed to professionals of the medicine that want to specialize in different branches of the Nuclear Medicine. Both courses have 220 present hours and it stops their approval the assistants they should surrender a final exam at open book that consists on the resolution of a practical exercise adapted to their professional practices. Until the present they have surrendered their exams satisfactorily approximately 2000 professionals coming from different areas of the Argentina and of several countries of Hispanic speech. e) Starting from 1992 the Course of Upgrade in Methodology of Radioisotopes directed to professionals that want to upgrade its knowledge in new radioisotopic

  3. Methodology for setting the reference levels in the measurements of the dose rate absorbed in air due to the environmental gamma radiation

    International Nuclear Information System (INIS)

    Dominguez Ley, Orlando; Capote Ferrera, Eduardo; Caveda Ramos, Celia; Alonso Abad, Dolores

    2008-01-01

    Full text: The methodology for setting the reference levels of the measurements of the gamma dose rate absorbed in the air is described. The registration level was obtained using statistical methods. To set the alarm levels, it was necessary to begin with certain affectation level, which activates the investigation operation mode when being reached. It is was necessary to transform this affectation level into values of the indicators selected to set the appearance of an alarm in the network, allowing its direct comparison and at the same time a bigger operability of this one. The affectation level was assumed as an effective dose of 1 mSv/y, which is the international dose limit for public. The conversion factor obtained in a practical way as a consequence of the Chernobyl accident was assumed, converting the value of annual effective dose into values of effective dose rate in air. These factors are the most important in our work, since the main task of the National Network of Environmental Radiological Surveillance of the Republic of Cuba is detecting accidents with a situations regional affectation, and this accident is precisely an example of pollution at this scale. The alarm level setting was based on the results obtained in the first year of the Chernobyl accident. For this purpose, some transformations were achieved. In the final results, a correction factor was introduced depending on the year season the measurement was made. It was taken into account the influence of different meteorological events on the measurement of this indicator. (author)

  4. A cross-sectional study with an improved methodology to assess occupational air pollution exposure and respiratory health in motorcycle taxi driving

    International Nuclear Information System (INIS)

    Lawin, Herve; Agodokpessi, Gildas; Ayelo, Paul; Kagima, Jacqueline; Sonoukon, Rodrigue; Mbatchou Ngahane, Bertrand H.; Awopeju, Olayemi; Vollmer, William M.; Nemery, Benoit; Burney, Peter; Fayomi, Benjamin

    2016-01-01

    Introduction: Motorcycle taxi driving is common in many African cities. This study tested whether this occupation is associated with more respiratory disorders in a context of widespread urban air pollution with an improved methodology. Methods: In a cross sectional study we compared 85 male motorcycle taxi drivers in the capital city of the Republic of Benin (Cotonou) with an age and neighborhood matched control group. All participants carried a portable carbon monoxide data logger for 8 hours per day to assess exposure to air pollution. Respiratory symptoms were obtained using a standardized questionnaire and pulmonary function was assessed by spirometry. Results: The two groups did not differ significantly (p > 0.10) in their age, height, educational level, and exposures to smoke from biomass fuels and tobacco products. The taxi drivers were exposed to higher mean (SD) levels of carbon monoxide (7.6 ± 4.9 ppmvs. 5.4 ± 3.8 ppm p = 0.001). They reported more phlegm and tended to have slightly lower levels of lung function, although these differences were not statistically significant. Conclusion: In this cross sectional study of young motorcycle taxi drivers with substantial exposure to urban traffic and a matched control group, we found no evidence for respiratory impairment. A follow-up of such study population with other pollution exposure surrogate and other clinical endpoint may provide a more robust conclusion regarding the exposure response in this professional group. - Highlights: • Need of improved study method to assess air pollution effect in exposed workers • This study compared motorcycle taxi drivers and a matched control group • Personal carbon monoxide exposure and respiratory disorders were collected • No evidence of more respiratory disorders even though pollutant exposure was higher

  5. A cross-sectional study with an improved methodology to assess occupational air pollution exposure and respiratory health in motorcycle taxi driving

    Energy Technology Data Exchange (ETDEWEB)

    Lawin, Herve, E-mail: hervelawin@yahoo.fr [Unit of Teaching and Research in Occupational and Environmental Health, Department of Public Health, Faculty of Health Sciences, University of Abomey-Calavi (Benin); Agodokpessi, Gildas [Centre National Hospitalier et Universitaire de Pneumo-Phtisiologie, Cotonou (Benin); Ayelo, Paul [Unit of Teaching and Research in Occupational and Environmental Health, Department of Public Health, Faculty of Health Sciences, University of Abomey-Calavi (Benin); Kagima, Jacqueline [Department of internal medicine, Egerton University (Kenya); Sonoukon, Rodrigue [Unit of Teaching and Research in Occupational and Environmental Health, Department of Public Health, Faculty of Health Sciences, University of Abomey-Calavi (Benin); Mbatchou Ngahane, Bertrand H. [Department of Internal Medicine, Douala General Hospital, Cameroon Faculty of Medicine and Pharmaceutical Sciences, University of Douala, Douala (Cameroon); Awopeju, Olayemi [Department of Medicine, Obafemi Awolowo University, Ile Ife (Nigeria); Vollmer, William M. [Center for Health Research, Kaiser Permanente Northwest, Portland (United States); Nemery, Benoit [Dept. of Public Health, Occupational and Environmental Insurance Medicine, KU Leuven, Leuven (Belgium); Burney, Peter [National Heart & Lung Institute, Imperial College, London (United Kingdom); Fayomi, Benjamin [Unit of Teaching and Research in Occupational and Environmental Health, Department of Public Health, Faculty of Health Sciences, University of Abomey-Calavi (Benin)

    2016-04-15

    Introduction: Motorcycle taxi driving is common in many African cities. This study tested whether this occupation is associated with more respiratory disorders in a context of widespread urban air pollution with an improved methodology. Methods: In a cross sectional study we compared 85 male motorcycle taxi drivers in the capital city of the Republic of Benin (Cotonou) with an age and neighborhood matched control group. All participants carried a portable carbon monoxide data logger for 8 hours per day to assess exposure to air pollution. Respiratory symptoms were obtained using a standardized questionnaire and pulmonary function was assessed by spirometry. Results: The two groups did not differ significantly (p > 0.10) in their age, height, educational level, and exposures to smoke from biomass fuels and tobacco products. The taxi drivers were exposed to higher mean (SD) levels of carbon monoxide (7.6 ± 4.9 ppmvs. 5.4 ± 3.8 ppm p = 0.001). They reported more phlegm and tended to have slightly lower levels of lung function, although these differences were not statistically significant. Conclusion: In this cross sectional study of young motorcycle taxi drivers with substantial exposure to urban traffic and a matched control group, we found no evidence for respiratory impairment. A follow-up of such study population with other pollution exposure surrogate and other clinical endpoint may provide a more robust conclusion regarding the exposure response in this professional group. - Highlights: • Need of improved study method to assess air pollution effect in exposed workers • This study compared motorcycle taxi drivers and a matched control group • Personal carbon monoxide exposure and respiratory disorders were collected • No evidence of more respiratory disorders even though pollutant exposure was higher.

  6. On the Ground or in the Air? A Methodological Experiment on Crop Residue Cover Measurement in Ethiopia.

    Science.gov (United States)

    Kosmowski, Frédéric; Stevenson, James; Campbell, Jeff; Ambel, Alemayehu; Haile Tsegay, Asmelash

    2017-10-01

    Maintaining permanent coverage of the soil using crop residues is an important and commonly recommended practice in conservation agriculture. Measuring this practice is an essential step in improving knowledge about the adoption and impact of conservation agriculture. Different data collection methods can be implemented to capture the field level crop residue coverage for a given plot, each with its own implication on survey budget, implementation speed and respondent and interviewer burden. In this paper, six alternative methods of crop residue coverage measurement are tested among the same sample of rural households in Ethiopia. The relative accuracy of these methods are compared against a benchmark, the line-transect method. The alternative methods compared against the benchmark include: (i) interviewee (respondent) estimation; (ii) enumerator estimation visiting the field; (iii) interviewee with visual-aid without visiting the field; (iv) enumerator with visual-aid visiting the field; (v) field picture collected with a drone and analyzed with image-processing methods and (vi) satellite picture of the field analyzed with remote sensing methods. Results of the methodological experiment show that survey-based methods tend to underestimate field residue cover. When quantitative data on cover are needed, the best estimates are provided by visual-aid protocols. For categorical analysis (i.e., >30% cover or not), visual-aid protocols and remote sensing methods perform equally well. Among survey-based methods, the strongest correlates of measurement errors are total farm size, field size, distance, and slope. Results deliver a ranking of measurement options that can inform survey practitioners and researchers.

  7. On the Ground or in the Air? A Methodological Experiment on Crop Residue Cover Measurement in Ethiopia

    Science.gov (United States)

    Kosmowski, Frédéric; Stevenson, James; Campbell, Jeff; Ambel, Alemayehu; Haile Tsegay, Asmelash

    2017-10-01

    Maintaining permanent coverage of the soil using crop residues is an important and commonly recommended practice in conservation agriculture. Measuring this practice is an essential step in improving knowledge about the adoption and impact of conservation agriculture. Different data collection methods can be implemented to capture the field level crop residue coverage for a given plot, each with its own implication on survey budget, implementation speed and respondent and interviewer burden. In this paper, six alternative methods of crop residue coverage measurement are tested among the same sample of rural households in Ethiopia. The relative accuracy of these methods are compared against a benchmark, the line-transect method. The alternative methods compared against the benchmark include: (i) interviewee (respondent) estimation; (ii) enumerator estimation visiting the field; (iii) interviewee with visual-aid without visiting the field; (iv) enumerator with visual-aid visiting the field; (v) field picture collected with a drone and analyzed with image-processing methods and (vi) satellite picture of the field analyzed with remote sensing methods. Results of the methodological experiment show that survey-based methods tend to underestimate field residue cover. When quantitative data on cover are needed, the best estimates are provided by visual-aid protocols. For categorical analysis (i.e., >30% cover or not), visual-aid protocols and remote sensing methods perform equally well. Among survey-based methods, the strongest correlates of measurement errors are total farm size, field size, distance, and slope. Results deliver a ranking of measurement options that can inform survey practitioners and researchers.

  8. International Comprehensive Ocean-Atmosphere Data Set (ICOADS) with Enhanced Trimming, Release 3

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains the latest official release of International Comprehensive Ocean-Atmosphere Data Set (ICOADS) with Enhanced Trimming, provided in a common...

  9. Synchronization Of TRIMs Principles In The Legislation Of Mining Sector In Indonesia

    Directory of Open Access Journals (Sweden)

    Agus Lanini

    2015-08-01

    Full Text Available The aims of this research are to know and explain synchronizing the principles of TRIMs at the foreign direct investment FDI and mining regulation in Indonesia. The research using normative research that conducted through library or document study such legal resources as primary sources secondary and tertiary sources that will be studied with applied legal approach comparative history and conceptual approach. Research results are revealing that synchronizing between the principles of TRIMs and Investment act 2007and Mineral and Coal act 2009 were not harmonized. It should be TRIMs and investment act 2007 have some similarity principles as harmonized even though Mineral and Coal act 2009 does not enough accessibility for the principles of TRIMs. Implication of the Mineral and Coal act 2009 raise a strong and real authority of the state even central or local government. Those policy results an overlap regulation caused state management system over natural resources ineffective.

  10. Novel trimming technique for tunable HTS microstrip filters

    Energy Technology Data Exchange (ETDEWEB)

    Sekiya, N. [Department of Electrical Engineering, Yamanashi University, Nakagawa-Sekiya Laboratory, 4-3-11 Takeda, Kofu 400-8511 (Japan)], E-mail: nsekiya@yamanashi.ac.jp; Nakagawa, Y. [Department of Electrical Engineering, Yamanashi University, Nakagawa-Sekiya Laboratory, 4-3-11 Takeda, Kofu 400-8511 (Japan); Saito, A.; Ohshima, S. [Yamagata University, 4-3-16 Johnan, Yonezawa 992-8510 (Japan)

    2008-09-15

    We have developed a method using additional electric pads for trimming tunable high-temperature superconducting (HTS) microstrip filters. These filters are generally tuned by adjusting the gap between a dielectric floating plate above the filter. When the floating plate approached the filter, the center frequency was shifted to a lower frequency. However, the insertion loss increases due to variation in the external quality factors varying from the design parameter. The external quality factors are usually controlled by adjusting the length of the input/output (I/O) coupled-line elements and the gap between the elements and the resonator. In our method, additional electric pads are distributed at the open-end of the I/O coupled-line elements of a 3-pole hairpin bandpass filter to enable adjustment of the external quality factors so as to reduce insertion loss. The electric pads consist of line-and-space patterns. They are eclectically connected to the coupled-line elements to adjust the line length and gap width and thereby control the external quality factors. An electromagnetic simulator was used for the design and analysis. The simulation results showed that the additional electric pads are effective in improving the insertion loss of the HTS bandpass filter after tuning.

  11. Novel trimming technique for tunable HTS microstrip filters

    International Nuclear Information System (INIS)

    Sekiya, N.; Nakagawa, Y.; Saito, A.; Ohshima, S.

    2008-01-01

    We have developed a method using additional electric pads for trimming tunable high-temperature superconducting (HTS) microstrip filters. These filters are generally tuned by adjusting the gap between a dielectric floating plate above the filter. When the floating plate approached the filter, the center frequency was shifted to a lower frequency. However, the insertion loss increases due to variation in the external quality factors varying from the design parameter. The external quality factors are usually controlled by adjusting the length of the input/output (I/O) coupled-line elements and the gap between the elements and the resonator. In our method, additional electric pads are distributed at the open-end of the I/O coupled-line elements of a 3-pole hairpin bandpass filter to enable adjustment of the external quality factors so as to reduce insertion loss. The electric pads consist of line-and-space patterns. They are eclectically connected to the coupled-line elements to adjust the line length and gap width and thereby control the external quality factors. An electromagnetic simulator was used for the design and analysis. The simulation results showed that the additional electric pads are effective in improving the insertion loss of the HTS bandpass filter after tuning

  12. Modeling of trim panels in the energy finite element analysis

    Science.gov (United States)

    Moravaeji, Seyed-Javid

    Modeling a trim panel is divided into finding the power exchange through two different paths: (i) the connection of the outer and inner panels (ii) through the layers directly. The vibrational power exchanged through the mounts is modeled as the connection of two parallel plates connected via a beam. Wave matrices representing plates and beams are derived separately; then a matrix method is proposed to solve for the wave amplitudes and hence the vibrational power exchange between the plates accordingly. A closed form formula for the case of connection of two identical plates is derived. For the power transmission loss directly through the layers, first transfer matrices representing layers made of different materials is considered. New matrices for a porous layer are derived. A method of finding the layered structure transfer matrix is proposed. It is concluded that in general a single isotropic layer cannot replace a structure accurately. Finally, on the basis of an equivalent transfer matrix, an optimization process for is proposed to replace the panel by a suitable set of layers.

  13. Energy balance of the metropolitan zone of the valley of Mexico, methodology and the entailment energy-air quality; Balance de energia de la zona metropolitana del valle de Mexico metodologia y la vinculacion energia - calidad del aire

    Energy Technology Data Exchange (ETDEWEB)

    Bazan Navarrete, Gerardo [Universidad Nacional Autonoma de Mexico, Mexico, D.F. (Mexico)

    2001-07-01

    The present document raises a methodology for the elaboration of the Energy Balance of the Metropolitan Zone of the Valley of Mexico (ZMVM), in order to unify criteria and to facilitate the work of entities and investigators, mainly of those that require the entailment of energy and environment. The applied methodology, the consolidated format and the caloric unity facilitates the insertion of the Energy Balance of the ZMVM within the National Balance of Energy. The regional balances of energy have the intention of knowing the energy consumption patterns in the ZMVM and the indexes of energy intensity by sector. They establish the relationship of the indexes of energy intensity with the local and global air quality of the region, performing studies of incidence with the main polluting agents and with the greenhouse effect gases. [Spanish] El presente documento plantea una metodologia para la elaboracion del Balance de Energia de la Zona Metropolitana del Valle de Mexico (ZMVM), con el proposito de unificar criterios y facilitar el trabajo de organismos e investigadores, sobre todo de aquellos que requieren vincular energia y medio ambiente. La metodologia aplicad, el formato consolidado y la unidad calorica facilitan la insercion del Balance de Energia de la ZMVM dentro del Balance Nacional de Energia. Los balances regionales de energia tienen el proposito de conocer los patrones de consumo de energia en la ZMVM y los indices de intensidad energetica por sector. Establecen la relacion de los indices de intensidad energetica con la calidad del aire local y global de la region, realizando estudios de incidencia con los principales contaminantes y con los gases de efecto invernadero.

  14. On the optimal trimming of high-throughput mRNA sequence data

    Directory of Open Access Journals (Sweden)

    Matthew D MacManes

    2014-01-01

    Full Text Available The widespread and rapid adoption of high-throughput sequencing technologies has afforded researchers the opportunity to gain a deep understanding of genome level processes that underlie evolutionary change, and perhaps more importantly, the links between genotype and phenotype. In particular, researchers interested in functional biology and adaptation have used these technologies to sequence mRNA transcriptomes of specific tissues, which in turn are often compared to other tissues, or other individuals with different phenotypes. While these techniques are extremely powerful, careful attention to data quality is required. In particular, because high-throughput sequencing is more error-prone than traditional Sanger sequencing, quality trimming of sequence reads should be an important step in all data processing pipelines. While several software packages for quality trimming exist, no general guidelines for the specifics of trimming have been developed. Here, using empirically derived sequence data, I provide general recommendations regarding the optimal strength of trimming, specifically in mRNA-Seq studies. Although very aggressive quality trimming is common, this study suggests that a more gentle trimming, specifically of those nucleotides whose Phred score < 2 or < 5, is optimal for most studies across a wide variety of metrics.

  15. Neuroanatomy-based matrix-guided trimming protocol for the rat brain.

    Science.gov (United States)

    Defazio, Rossella; Criado, Ana; Zantedeschi, Valentina; Scanziani, Eugenio

    2015-02-01

    Brain trimming through defined neuroanatomical landmarks is recommended to obtain consistent sections in rat toxicity studies. In this article, we describe a matrix-guided trimming protocol that uses channels to reproduce coronal levels of anatomical landmarks. Both setup phase and validation study were performed on Han Wistar male rats (Crl:WI(Han)), 10-week-old, with bodyweight of 298 ± 29 (SD) g, using a matrix (ASI-Instruments(®), Houston, TX) fitted for brains of rats with 200 to 400 g bodyweight. In the setup phase, we identified eight channels, that is, 6, 8, 10, 12, 14, 16, 19, and 21, matching the recommended landmarks midway to the optic chiasm, frontal pole, optic chiasm, infundibulum, mamillary bodies, midbrain, middle cerebellum, and posterior cerebellum, respectively. In the validation study, we trimmed the immersion-fixed brains of 60 rats using the selected channels to determine how consistently the channels reproduced anatomical landmarks. Percentage of success (i.e., presence of expected targets for each level) ranged from 89 to 100%. Where 100% success was not achieved, it was noted that the shift in brain trimming was toward the caudal pole. In conclusion, we developed and validated a trimming protocol for the rat brain that allow comparable extensiveness, homology, and relevance of coronal sections as the landmark-guided trimming with the advantage of being quickly learned by technicians. © 2014 by The Author(s).

  16. Development and Operation of an Automatic Rotor Trim Control System for the UH-60 Individual Blade Control Wind Tunnel Test

    Science.gov (United States)

    Theodore, Colin R.; Tischler, Mark B.

    2010-01-01

    An automatic rotor trim control system was developed and successfully used during a wind tunnel test of a full-scale UH-60 rotor system with Individual Blade Control (IBC) actuators. The trim control system allowed rotor trim to be set more quickly, precisely and repeatably than in previous wind tunnel tests. This control system also allowed the rotor trim state to be maintained during transients and drift in wind tunnel flow, and through changes in IBC actuation. The ability to maintain a consistent rotor trim state was key to quickly and accurately evaluating the effect of IBC on rotor performance, vibration, noise and loads. This paper presents details of the design and implementation of the trim control system including the rotor system hardware, trim control requirements, and trim control hardware and software implementation. Results are presented showing the effect of IBC on rotor trim and dynamic response, a validation of the rotor dynamic simulation used to calculate the initial control gains and tuning of the control system, and the overall performance of the trim control system during the wind tunnel test.

  17. Identification and characterization of a nuclear localization signal of TRIM28 that overlaps with the HP1 box

    International Nuclear Information System (INIS)

    Moriyama, Tetsuji; Sangel, Percival; Yamaguchi, Hiroki; Obuse, Chikashi; Miyamoto, Yoichi; Oka, Masahiro; Yoneda, Yoshihiro

    2015-01-01

    Tripartite motif-containing 28 (TRIM28) is a transcription regulator, which forms a repressor complex containing heterochromatin protein 1 (HP1). Here, we report identification of a nuclear localization signal (NLS) within the 462-494 amino acid region of TRIM28 that overlaps with its HP1 binding site, HP1 box. GST-pulldown experiments revealed the interaction of the arginine-rich TRIM28 NLS with various importin α subtypes (α1, α2 and α4). In vitro transport assay demonstrated that nuclear localization of GFP-TRIM28 NLS is mediated by importin αs, in conjunction with importin β1 and Ran. Further, we demonstrated that HP1 and importin αs compete for binding to TRIM28. Together, our findings suggest that importin α has an essential role in the nuclear delivery and preferential HP1 interaction of TRIM28. - Highlights: • TRIM28 contains an NLS within the 462-494 amino acid region. • The nuclear import of TRIM28 is mediated by importin α/importin β1. • TRIM28 NLS overlaps with HP1 Box. • HP1 and importin α compete for binding to TRIM28

  18. Identification and characterization of a nuclear localization signal of TRIM28 that overlaps with the HP1 box

    Energy Technology Data Exchange (ETDEWEB)

    Moriyama, Tetsuji; Sangel, Percival [Laboratory of Nuclear Transport Dynamics, National Institutes of Biomedical Innovation, Health and Nutrition (NIBIOHN), Osaka 567-0085 (Japan); Yamaguchi, Hiroki [School of Medicine, Osaka University, Osaka 565-0871 (Japan); Obuse, Chikashi [Graduate School of Life Science, Hokkaido University, Sapporo 001-0021 (Japan); Miyamoto, Yoichi [Laboratory of Nuclear Transport Dynamics, National Institutes of Biomedical Innovation, Health and Nutrition (NIBIOHN), Osaka 567-0085 (Japan); Oka, Masahiro, E-mail: moka@nibiohn.go.jp [Laboratory of Nuclear Transport Dynamics, National Institutes of Biomedical Innovation, Health and Nutrition (NIBIOHN), Osaka 567-0085 (Japan); Laboratory of Biomedical Innovation, Graduate School of Pharmaceutical Sciences, Osaka University, Osaka 565-0871 (Japan); Yoneda, Yoshihiro, E-mail: y-yoneda@nibiohn.go.jp [National Institutes of Biomedical Innovation, Health and Nutrition (NIBIOHN), Osaka 567-0085 (Japan); Laboratory of Biomedical Innovation, Graduate School of Pharmaceutical Sciences, Osaka University, Osaka 565-0871 (Japan)

    2015-07-03

    Tripartite motif-containing 28 (TRIM28) is a transcription regulator, which forms a repressor complex containing heterochromatin protein 1 (HP1). Here, we report identification of a nuclear localization signal (NLS) within the 462-494 amino acid region of TRIM28 that overlaps with its HP1 binding site, HP1 box. GST-pulldown experiments revealed the interaction of the arginine-rich TRIM28 NLS with various importin α subtypes (α1, α2 and α4). In vitro transport assay demonstrated that nuclear localization of GFP-TRIM28 NLS is mediated by importin αs, in conjunction with importin β1 and Ran. Further, we demonstrated that HP1 and importin αs compete for binding to TRIM28. Together, our findings suggest that importin α has an essential role in the nuclear delivery and preferential HP1 interaction of TRIM28. - Highlights: • TRIM28 contains an NLS within the 462-494 amino acid region. • The nuclear import of TRIM28 is mediated by importin α/importin β1. • TRIM28 NLS overlaps with HP1 Box. • HP1 and importin α compete for binding to TRIM28.

  19. TRIM44 Is a Poor Prognostic Factor for Breast Cancer Patients as a Modulator of NF-κB Signaling.

    Science.gov (United States)

    Kawabata, Hidetaka; Azuma, Kotaro; Ikeda, Kazuhiro; Sugitani, Ikuko; Kinowaki, Keiichi; Fujii, Takeshi; Osaki, Akihiko; Saeki, Toshiaki; Horie-Inoue, Kuniko; Inoue, Satoshi

    2017-09-08

    Many of the tripartite motif (TRIM) proteins function as E3 ubiquitin ligases and are assumed to be involved in various events, including oncogenesis. In regard to tripartite motif-containing 44 (TRIM44), which is an atypical TRIM family protein lacking the RING finger domain, its pathophysiological significance in breast cancer remains unknown. We performed an immunohistochemical study of TRIM44 protein in clinical breast cancer tissues from 129 patients. The pathophysiological role of TRIM44 in breast cancer was assessed by modulating TRIM44 expression in MCF-7 and MDA-MB-231 breast cancer cells. TRIM44 strong immunoreactivity was significantly associated with nuclear grade ( p = 0.033), distant disease-free survival ( p = 0.031) and overall survival ( p = 0.027). Multivariate analysis revealed that the TRIM44 status was an independent prognostic factor for distant disease-free survival ( p = 0.005) and overall survival ( p = 0.002) of patients. siRNA-mediated TRIM44 knockdown significantly decreased the proliferation of MCF-7 and MDA-MB-231 cells and inhibited the migration of MDA-MB-231 cells. Microarray analysis and qRT-PCR showed that TRIM44 knockdown upregulated CDK19 and downregulated MMP1 in MDA-MB-231 cells. Notably, TRIM44 knockdown impaired nuclear factor-kappa B (NF-κB)-mediated transcriptional activity stimulated by tumor necrosis factor α (TNFα). Moreover, TRIM44 knockdown substantially attenuated the TNFα-dependent phosphorylation of the p65 subunit of NF-κB and IκBα in both MCF-7 and MDA-MB-231 cells. TRIM44 would play a role in the progression of breast cancer by promoting cell proliferation and migration, as well as by enhancing NF-κB signaling.

  20. A probabilistic and multi-objective conceptual design methodology for the evaluation of thermal management systems on air-breathing hypersonic vehicles

    Science.gov (United States)

    Ordaz, Irian

    This thesis addresses the challenges associated with thermal management systems (TMS) evaluation and selection in the conceptual design of hypersonic, air-breathing vehicles with sustained cruise. The proposed methodology identifies analysis tools and techniques which allow the proper investigation of the design space for various thermal management technologies. The design space exploration environment and alternative multi-objective decision making technique defined as Pareto-based Joint Probability Decision Making (PJPDM) is based on the approximation of 3-D Pareto frontiers and probabilistic technology effectiveness maps. These are generated through the evaluation of a Pareto Fitness function and Monte Carlo analysis. In contrast to Joint Probability Decision Making (JPDM), the proposed PJPDM technique does not require preemptive knowledge of weighting factors for competing objectives or goal constraints which can introduce bias into the final solution. Preemptive bias in a complex problem can degrade the overall capabilities of the final design. The implementation of PJPDM in this thesis eliminates the need for the numerical optimizer which is required with JPDM in order to improve upon a solution. In addition, a physics-based formulation is presented for the quantification of TMS safety effectiveness corresponding to debris impact/damage and how it can be applied towards risk mitigation. Lastly, a formulation loosely based on non-preemptive Goal Programming with equal weighted deviations is provided for the resolution of the inverse design space. This key step helps link vehicle capabilities to TMS technology subsystems in a top-down design approach. The methodology provides the designer more knowledge up front to help make proper engineering decisions and assumptions in the conceptual design phase regarding which technologies show greatest promise, and how to guide future technology research.

  1. Assessment of gamma irradiation heating and damage in miniature neutron source reactor vessel using computational methods and SRIM - TRIM code

    International Nuclear Information System (INIS)

    Appiah-Ofori, F. F.

    2014-07-01

    The Effects of Gamma Radiation Heating and Irradiation Damage in the reactor vessel of Ghana Research Reactor 1, Miniature Neutron Source Reactor were assessed using Implicit Control Volume Finite Difference Numerical Computation and validated by SRIM - TRIM Code. It was assumed that 5.0 MeV of gamma rays from the reactor core generate heat which interact and absorbed completely by the interior surface of the MNSR vessel which affects it performance due to the induced displacement damage. This displacement damage is as result of lattice defects being created which impair the vessel through formation of point defect clusters such as vacancies and interstitiaIs which can result in dislocation loops and networks, voids and bubbles and causing changes in the layers in the thickness of the vessel. The microscopic defects produced in the vessel due to γ - radiation damage are referred to as radiation damage while the defects thus produced modify the macroscopic properties of the vessel which are also known as the radiation effects. These radiation damage effects are of major concern for materials used in nuclear energy production. In this study, the overall objective was to assess the effects of gamma radiation heating and damage in GHARR - I MNSR vessel by a well-developed Mathematical model, Analytical and Numerical solutions, simulating the radiation damage in the vessel. SRIM - TRIM Code was used as a computational tool to determine the displacement per atom (dpa) associated with radiation damage while implicit Control Volume Finite Difference Method was used to determine the temperature profile within the vessel due to γ - radiation heating respectively. The methodology adopted in assessing γ - radiation heating in the vessel involved development of the One-Dimensional Steady State Fourier Heat Conduction Equation with Volumetric Heat Generation both analytical and implicit Control Volume Finite Difference Method approach to determine the maximum temperature and

  2. TRIM24 promotes glioma progression and enhances chemoresistance through activation of the PI3K/Akt signaling pathway.

    Science.gov (United States)

    Zhang, L-H; Yin, A-A; Cheng, J-X; Huang, H-Y; Li, X-M; Zhang, Y-Q; Han, N; Zhang, X

    2015-01-29

    The tripartite motif protein TRIM24 (tripartite motif-containing 24) has been found to play distinct roles in tumor development and progression, according to different tumor contexts. However, it remains elusive whether TRIM24 plays a role in malignant gliomas that are the most common and deadly primary brain tumors in adults. We report here that TRIM24 expression is positively correlated with glioma malignancy and is negatively associated with prognosis of patients with newly diagnosed glioblastoma, which is the most malignant form of gliomas but displays highly heterogeneous clinical outcome. The multivariate Cox regression analysis demonstrates the independent predictive value of TRIM24 expression level for overall and progression-free survival. Knockdown of TRIM24 suppresses cell proliferation, cell cycle progression, clone formation and in vivo tumor development, whereas overexpression of TRIM24 promotes cell growth. Chromatin immunoprecipitation, real-time reverse transcription-PCR and mutation analyses demonstrate that TRIM24 binds to the PIK3CA promoter via its PHD-Bromo domain to activate the transcription of PIK3CA gene, thus enhancing phosphatidylinositide 3-kinase (PI3K)/Akt signaling. The pan-PI3K inhibitor LY294002 and small interfering RNA targeting PIK3CA both abrogate the growth-promoting effect of TRIM24. Moreover, TRIM24 regulates the expression of DNA repair enzyme O(6)-methylguanine-DNA methyltransferase (MGMT) through PI3K/Akt/nuclear factor-κB signaling transduction and enhances resistance to temozolomide, the standard chemotherapeutic agent for glioblastoma. Finally, glioblastoma patients with low TRIM24 expression benefit from chemotherapy, whereas those with high TRIM24 expression do not have such benefit. Our results suggest that TRIM24 might serve as a potential prognostic marker and therapeutic target for the management of malignant gliomas.

  3. The Norwegian Emission Inventory 2010. Documentation of methodologies for estimating emissions of greenhouse gases and long-range transboundary air pollutants

    Energy Technology Data Exchange (ETDEWEB)

    Sandmo, Trond (ed.)

    2010-06-15

    The Norwegian emission inventory is a joint undertaking between the Climate and Pollution Agency (Klif) and Statistics Norway. Statistics Norway is responsible for the collection and development of activity data, and emission figures are derived from models operated by Statistics Norway. The Climate and Pollution Agency is responsible for the emission factors, for providing data from specific industries and sources and for considering the quality, and assuring necessary updating, of emissions models like e.g. the road traffic model and calculation of methane emissions from landfills. Emission data are used for a range of national applications and for international reporting. The Climate and Pollution Agency is responsible for the Norwegian reporting to United Nations Framework Convention on Climate Change (UNFCCC) and to United Nations Economic Commission Europe (UN-ECE). This report documents the methodologies used in the Norwegian emission inventory of greenhouse gases (GHG), acidifying pollutants, heavy metals (HM) and persistent organic pollutants (POPs). The documentation will also serve as a part of the National Inventory Report submitted by Norway to the United Nations Framework Convention on Climate Change (UNFCCC), and as documentation of the reported emissions to UNECE for the pollutants restricted by CLRTAP (Convention on Long-Range Transboundary Air Pollution). LULUCF is not considered in this report, see the National Inventory Report (Climate and Pollution Agency 2010) for documentation on this topic. This report replaces the previous documentation of the emission model, (Sandmo 2009), and is the latest annually updated version of a report edited by Britta Hoem in 2005. The most important changes since last year's documentation are: Emissions of CH{sub 4} and N{sub 2}O from well testing of crude oil off shore have been included - these have previously not been estimated Emissions of CH{sub 4} from enteric fermentation have increased for the whole

  4. The Transcriptional Repressive Activity of KRAB Zinc Finger Proteins Does Not Correlate with Their Ability to Recruit TRIM28.

    Directory of Open Access Journals (Sweden)

    Kristin E Murphy

    Full Text Available KRAB domain Zinc finger proteins are one of the most abundant families of transcriptional regulators in higher vertebrates. The prevailing view is that KRAB domain proteins function as potent transcriptional repressors by recruiting TRIM28 and promoting heterochromatin spreading. However, the extent to which all KRAB domain proteins are TRIM28-dependent transcriptional repressors is currently unclear. Our studies on mouse ZFP568 revealed that TRIM28 recruitment by KRAB domain proteins is not sufficient to warrant transcriptional repressive activity. By using luciferase reporter assays and yeast two-hybrid experiments, we tested the ability of ZFP568 and other mouse KRAB domain proteins to repress transcription and bind TRIM28. We found that some mouse KRAB domain proteins are poor transcriptional repressors despite their ability to recruit TRIM28, while others showed strong KRAB-dependent transcriptional repression, but no TRIM28 binding. Together, our results show that the transcriptional repressive activity of KRAB-ZNF proteins does not correlate with their ability to recruit TRIM28, and provide evidence that KRAB domains can regulate transcription in a TRIM28-independent fashion. Our findings challenge the current understanding of the molecular mechanisms used by KRAB domain proteins to control gene expression and highlight that a high percentage of KRAB domain proteins in the mouse genome differ from the consensus KRAB sequence at amino acid residues that are critical for TRIM28 binding and/or repressive activity.

  5. Molecular characterization of a CpTRIM35-like protein and its splice variants from whitespotted bamboo shark (Chiloscyllium plagiosum)

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xinshang, E-mail: sanmaosound@163.com; Zhao, Heng, E-mail: hengzhao2000@gmail.com; Chen, Yeyu, E-mail: cyyleaf@126.com; Luo, Huiying, E-mail: luohuiying@caas.cn; Yao, Bin, E-mail: binyao@caas.cn

    2014-10-24

    Highlights: • A TRIM gene and three splice variants were firstly cloned from elasmobranch fish. • The genes were constitutively expressed with high levels in spleen and kidney. • The gene products were distributed in cytoplasm alone or cytoplasm and nucleus. • As E3 ubiquitin ligases, the proteins differed in immune responses to challenges. - Abstract: The tripartite motif (TRIM) proteins play important roles in a broad range of biological processes, including apoptosis, cell proliferation and innate immunity response. In this study, a TRIM gene and its three splice variants were cloned from an elasmobranch fish—whitespotted bamboo shark (Chiloscyllium plagiosum Bennett). Phylogenetic analysis indicated that the gene was closely related to TRIM35 homologs, thus termed CpTRIM35-like. Deduced CpTRIM35 has a RBCC-PRY/SPRY structure typical of TRIM proteins, and its splice variants (CpTRIM35-1–3) have different truncations at the C-terminus. The gene products were constitutively expressed in adult sharks with the highest levels in spleen and kidney. The different subcellular locations, upregulation upon LPS and poly I:C stimulation, and significant E3 ubiquitin ligase activities suggested their different roles in immune responses as an E3 ubiquitin ligase. This is the first TRIM protein ever characterized in elasmobranch fish.

  6. Molecular characterization of a CpTRIM35-like protein and its splice variants from whitespotted bamboo shark (Chiloscyllium plagiosum)

    International Nuclear Information System (INIS)

    Zhang, Xinshang; Zhao, Heng; Chen, Yeyu; Luo, Huiying; Yao, Bin

    2014-01-01

    Highlights: • A TRIM gene and three splice variants were firstly cloned from elasmobranch fish. • The genes were constitutively expressed with high levels in spleen and kidney. • The gene products were distributed in cytoplasm alone or cytoplasm and nucleus. • As E3 ubiquitin ligases, the proteins differed in immune responses to challenges. - Abstract: The tripartite motif (TRIM) proteins play important roles in a broad range of biological processes, including apoptosis, cell proliferation and innate immunity response. In this study, a TRIM gene and its three splice variants were cloned from an elasmobranch fish—whitespotted bamboo shark (Chiloscyllium plagiosum Bennett). Phylogenetic analysis indicated that the gene was closely related to TRIM35 homologs, thus termed CpTRIM35-like. Deduced CpTRIM35 has a RBCC-PRY/SPRY structure typical of TRIM proteins, and its splice variants (CpTRIM35-1–3) have different truncations at the C-terminus. The gene products were constitutively expressed in adult sharks with the highest levels in spleen and kidney. The different subcellular locations, upregulation upon LPS and poly I:C stimulation, and significant E3 ubiquitin ligase activities suggested their different roles in immune responses as an E3 ubiquitin ligase. This is the first TRIM protein ever characterized in elasmobranch fish

  7. TRIM32 promotes retinoic acid receptor α-mediated differentiation in human promyelogenous leukemic cell line HL60

    International Nuclear Information System (INIS)

    Sato, Tomonobu; Okumura, Fumihiko; Iguchi, Akihiro; Ariga, Tadashi; Hatakeyama, Shigetsugu

    2012-01-01

    Highlights: ► TRIM32 enhanced RARα-mediated transcriptional activity even in the absence of RA. ► TRIM32 stabilized RARα in the human promyelogenous leukemic cell line HL60. ► Overexpression of TRIM32 in HL60 cells induced granulocytic differentiation. ► TRIM32 may function as a coactivator for RARα-mediated transcription in APL cells. -- Abstract: Ubiquitination, one of the posttranslational modifications, appears to be involved in the transcriptional activity of nuclear receptors including retinoic acid receptor α (RARα). We previously reported that an E3 ubiquitin ligase, TRIM32, interacts with several important proteins including RARα and enhances transcriptional activity of RARα in mouse neuroblastoma cells and embryonal carcinoma cells. Retinoic acid (RA), which acts as a ligand to nuclear receptors including RARα, plays crucial roles in development, differentiation, cell cycles and apoptosis. In this study, we found that TRIM32 enhances RARα-mediated transcriptional activity even in the absence of RA and stabilizes RARα in the human promyelogenous leukemic cell line HL60. Moreover, we found that overexpression of TRIM32 in HL60 cells suppresses cellular proliferation and induces granulocytic differentiation even in the absence of RA. These findings suggest that TRIM32 functions as one of the coactivators for RARα-mediated transcription in acute promyelogenous leukemia (APL) cells, and thus TRIM32 may become a potentially therapeutic target for APL.

  8. Molecular Characterization, Tissue Distribution and Expression, and Potential Antiviral Effects of TRIM32 in the Common Carp (Cyprinus carpio)

    Science.gov (United States)

    Wang, Yeda; Li, Zeming; Lu, Yuanan; Hu, Guangfu; Lin, Li; Zeng, Lingbing; Zhou, Yong; Liu, Xueqin

    2016-01-01

    Tripartite motif-containing protein 32 (TRIM32) belongs to the tripartite motif (TRIM) family, which consists of a large number of proteins containing a RING (Really Interesting New Gene) domain, one or two B-box domains, and coiled coil motif followed by different C-terminal domains. The TRIM family is known to be implicated in multiple cellular functions, including antiviral activity. However, it is presently unknown whether TRIM32 of common carp (Cyprinus carpio) has the antiviral effect. In this study, the sequence, expression, and antiviral function of TRIM32 homolog from common carp were analyzed. The full-length coding sequence region of trim32 was cloned from common carp. The results showed that the expression of TRIM32 (mRNA) was highest in the brain, remained stably expressed during embryonic development, and significantly increased following spring viraemia of carp virus (SVCV) infection. Transient overexpression of TRIM32 in affected Epithelioma papulosum cyprinid cells led to significant decrease of SVCV production as compared to the control group. These results suggested a potentially important role of common carp TRIM32 in enhancing host immune response during SVCV infection both in vivo and in vitro. PMID:27735853

  9. TRIM56-mediated monoubiquitination of cGAS for cytosolic DNA sensing.

    Science.gov (United States)

    Seo, Gil Ju; Kim, Charlotte; Shin, Woo-Jin; Sklan, Ella H; Eoh, Hyungjin; Jung, Jae U

    2018-02-09

    Intracellular nucleic acid sensors often undergo sophisticated modifications that are critical for the regulation of antimicrobial responses. Upon recognition of DNA, the cytosolic sensor cyclic GMP-AMP (cGAMP) synthase (cGAS) produces the second messenger cGAMP, which subsequently initiates downstream signaling to induce interferon-αβ (IFNαβ) production. Here we report that TRIM56 E3 ligase-induced monoubiquitination of cGAS is important for cytosolic DNA sensing and IFNαβ production to induce anti-DNA viral immunity. TRIM56 induces the Lys335 monoubiquitination of cGAS, resulting in a marked increase of its dimerization, DNA-binding activity, and cGAMP production. Consequently, TRIM56-deficient cells are defective in cGAS-mediated IFNαβ production upon herpes simplex virus-1 (HSV-1) infection. Furthermore, TRIM56-deficient mice show impaired IFNαβ production and high susceptibility to lethal HSV-1 infection but not to influenza A virus infection. This adds TRIM56 as a crucial component of the cytosolic DNA sensing pathway that induces anti-DNA viral innate immunity.

  10. Endoscopic removal and trimming of distal self-expandable metallic biliary stents

    Science.gov (United States)

    Ishii, Kentaro; Itoi, Takao; Sofuni, Atsushi; Itokawa, Fumihide; Tsuchiya, Takayoshi; Kurihara, Toshio; Tsuji, Shujiro; Ikeuchi, Nobuhito; Umeda, Junko; Moriyasu, Fuminori; Tsuchida, Akihiko

    2011-01-01

    AIM: To evaluate the efficacy and safety of endoscopic removal and trimming of self-expandable metallic stents (SEMS). METHODS: All SEMS had been placed for distal biliary strictures. Twenty-seven endoscopic procedures were performed in 19 patients in whom SEMS (one uncovered and 18 covered) removal had been attempted, and 8 patients in whom stent trimming using argon plasma coagulation (APC) had been attempted at Tokyo Medical University Hospital. The APC settings were: voltage 60-80 W and gas flow at 1.5 L/min. RESULTS: The mean stent indwelling period for all patients in whom stent removal had been attempted was 113.7 ± 77.6 d (range, 8-280 d). Of the 19 patients in whom removal of the SEMS had been attempted, the procedure was successful in 14 (73.7%) without procedure-related adverse events. The indwelling period in the stent removable group was shorter than that in the unremovable group (94.9 ± 71.5 d vs 166.2 ± 76.2 d, P = 0.08). Stent trimming was successful for all patients with one minor adverse event consisting of self-limited hemorrhage. Trimming time ranged from 11 to 16 min. CONCLUSION: Although further investigations on larger numbers of cases are necessary to accumulate evidence, the present data suggested that stent removal and stent trimming is feasible and effective for stent-related complications. PMID:21677835

  11. Moving characteristics of single file passengers considering the effect of ship trim and heeling

    Science.gov (United States)

    Sun, Jinlu; Lu, Shouxiang; Lo, Siuming; Ma, Jian; Xie, Qimiao

    2018-01-01

    Ship listing and motion affects the movement pattern of passengers on board, thus pedestrian traffic and evacuation dynamics would be significantly different from those on level ground. To quantify the influence of ship listing and motion on passenger evacuation, we designed a ship corridor simulator, with which we performed single-file pedestrian movement experiments considering the effect of trim and heeling. Results indicated that density is not the only factor that affects pedestrian speed under ship trim or heeling conditions, for that both individual walking speed and group walking speed would be greatly attenuated due to the influence of the trim angles. However, heeling angles show less impact on speed when compared with trim angles. In addition, the speed correlation coefficient between the adjacent experimental subjects would be higher with larger angles and lower speed. Moreover, both female and male experimental subjects need similar distance headway for walking in different trim or heeling conditions. Furthermore, experimental subjects with lower individual walking speed need longer time headway to keep enough distance headway. This work will provide fundamental guidance to the development of evacuation models and the design of evacuation facilities on board.

  12. Targeting TRIM5α in HIV Cure Strategies for the CRISPR-Cas9 Era

    Directory of Open Access Journals (Sweden)

    Daryl Anne Victoria Weatherley

    2017-11-01

    Full Text Available In the past decade, studies of innate immune activity against HIV-1 and other retroviruses have revealed a powerful array of host factors that can attack the virus at various stages of its life cycle in human and primate cells, raising the prospect that these antiviral factors could be manipulated in immunotherapeutic strategies for HIV infection. This has not proved straightforward: while HIV accessory genes encode proteins that subvert or destroy many of these restriction factors, others, such as human TRIM5α show limited potency against HIV-1. However, HIV-1 is much more susceptible to simian versions of TRIM5α: could this information be translated into the development of an effective gene therapy for HIV infection? Reigniting research into the restriction factor TRIM5α in the era of superior gene editing technology such as CRISPR-Cas9 presents an exciting opportunity to revisit this prospect.

  13. HIRFL-SSC trim coil currents calculation by conjugate gradients method

    International Nuclear Information System (INIS)

    Liu, W.

    2005-01-01

    For accelerating different kinds of ions to various energies, the HIRFL-SSC should form the corresponding isochronous magnetic field by its main coil and trim coils. Previously, there were errors in fitting the theoretical isochronous magnetic field in the small radius region, which led to some operation difficulties for ion acceleration in the inject region. After further investigation of the restrictive condition of the maximum current limitation, the trim coil currents for fitting the theoretical isochronous magnetic field were recalculated by the conjugate gradients method. Better results were obtained in the operation of HIRFL-SSC. This article introduces the procedure to calculate the trim coil currents. The calculation method of conjugate gradients is introduced and the fitting error is analysed. (author)

  14. The Norwegian Emission Inventory 2011. Documentation of methodologies for estimating emissions of greenhouse gases and long-range transboundary air pollutants

    Energy Technology Data Exchange (ETDEWEB)

    Sandmo, Trond

    2012-07-01

    The Norwegian emission inventory is a joint undertaking between the Climate and Pollution Agency1 and Statistics Norway. Statistics Norway is responsible for the collection and development of activity data, and emission figures are derived from models operated by Statistics Norway. The Climate and Pollution Agency is responsible for the emission factors, for providing data from specific industries and sources and for considering the quality, and assuring necessary updating, of emission models like, e.g., the road traffic model and calculation of methane emissions from landfills. Emission data are used for a range of national applications and for international reporting. The Climate and Pollution Agency is responsible for the Norwegian reporting to United Nations Framework Convention on Climate Change (UNFCCC) and to United Nations Economic Commission Europe (UN-ECE). This report documents the methodologies used in the Norwegian emission inventory of greenhouse gases (GHG), acidifying pollutants, heavy metals (HM) and persistent organic pollutants (POPs). The documentation will also serve as a part of the National Inventory Report submitted by Norway to the United Nations Framework Convention on Climate Change (UNFCCC), and as documentation of the reported emissions to UNECE for the pollutants restricted by CLRTAP (Convention on Long-Range Transboundary Air Pollution). LULUCF is not considered in this report, see the National Inventory Report (Climate and Pollution Agency 2011b) for documentation on this topic. This report replaces the previous documentation of the emission model (Sandmo 2010), and is the latest annually updated version of a report edited by Britta Hoem in 2005. The most important changes since last year's documentation are: To define the different economic sectors in the Norwegian emission model, the standard industrial classification SIC2007 has replaced the previous SIC2002 (Appendix F) A new model for calculating emissions to air (HBEFA

  15. The Norwegian Emission Inventory 2011. Documentation of methodologies for estimating emissions of greenhouse gases and long-range transboundary air pollutants

    Energy Technology Data Exchange (ETDEWEB)

    Sandmo, Trond

    2012-07-01

    The Norwegian emission inventory is a joint undertaking between the Climate and Pollution Agency1 and Statistics Norway. Statistics Norway is responsible for the collection and development of activity data, and emission figures are derived from models operated by Statistics Norway. The Climate and Pollution Agency is responsible for the emission factors, for providing data from specific industries and sources and for considering the quality, and assuring necessary updating, of emission models like, e.g., the road traffic model and calculation of methane emissions from landfills. Emission data are used for a range of national applications and for international reporting. The Climate and Pollution Agency is responsible for the Norwegian reporting to United Nations Framework Convention on Climate Change (UNFCCC) and to United Nations Economic Commission Europe (UN-ECE). This report documents the methodologies used in the Norwegian emission inventory of greenhouse gases (GHG), acidifying pollutants, heavy metals (HM) and persistent organic pollutants (POPs). The documentation will also serve as a part of the National Inventory Report submitted by Norway to the United Nations Framework Convention on Climate Change (UNFCCC), and as documentation of the reported emissions to UNECE for the pollutants restricted by CLRTAP (Convention on Long-Range Transboundary Air Pollution). LULUCF is not considered in this report, see the National Inventory Report (Climate and Pollution Agency 2011b) for documentation on this topic. This report replaces the previous documentation of the emission model (Sandmo 2010), and is the latest annually updated version of a report edited by Britta Hoem in 2005. The most important changes since last year's documentation are: To define the different economic sectors in the Norwegian emission model, the standard industrial classification SIC2007 has replaced the previous SIC2002 (Appendix F) A new model for calculating emissions to air (HBEFA) from

  16. Trimming algorithm of frequency modulation for CIAE-230 MeV proton superconducting synchrocyclotron model cavity

    Energy Technology Data Exchange (ETDEWEB)

    Li, Pengzhan, E-mail: lipengzhan@ciae.ac.cn; Zhang, Tianjue; Ji, Bin; Hou, Shigang; Guo, Juanjuan; Yin, Meng; Xing, Jiansheng; Lv, Yinlong; Guan, Fengping; Lin, Jun

    2017-01-21

    A new project, the 230 MeV proton superconducting synchrocyclotron for cancer therapy, was proposed at CIAE in 2013. A model cavity is designed to verify the frequency modulation trimming algorithm featuring a half-wave structure and eight sets of rotating blades for 1 kHz frequency modulation. Based on the electromagnetic (EM) field distribution analysis of the model cavity, the variable capacitor works as a function of time and the frequency can be written in Maclaurin series. Curve fitting is applied for theoretical frequency and original simulation frequency. The second-order fitting excels at the approximation given its minimum variance. Constant equivalent inductance is considered as an important condition in the calculation. The equivalent parameters of theoretical frequency can be achieved through this conversion. Then the trimming formula for rotor blade outer radius is found by discretization in time domain. Simulation verification has been performed and the results show that the calculation radius with minus 0.012 m yields an acceptable result. The trimming amendment in the time range of 0.328–0.4 ms helps to reduce the frequency error to 0.69% in Simulation C with an increment of 0.075 mm/0.001 ms, which is half of the error in Simulation A (constant radius in 0.328–0.4 ms). The verification confirms the feasibility of the trimming algorithm for synchrocyclotron frequency modulation. - Highlights: • A model cavity is designed to verify the trimming algorithm of frequency modulation. • The RF frequency is expressed by fitting approximation and Maclaurin series. • The variable capacitor of the cavity works as a function of time. • The trimming formula for blade radius is found by discretization in time domain. • The amendment solution helps to reduce the frequency error.

  17. S-nitrosylation of TRIM72 at cysteine 144 is critical for protection against oxidation-induced protein degradation and cell death.

    Science.gov (United States)

    Kohr, Mark J; Evangelista, Alicia M; Ferlito, Marcella; Steenbergen, Charles; Murphy, Elizabeth

    2014-04-01

    Oxidative stress and membrane damage following myocardial ischemia/reperfusion injury are important contributors to cardiomyocyte death and the loss of myocardial function. Our previous study identified cysteine 144 (C144) of tripartite motif-containing protein 72 (TRIM72) as a potential site for S-nitrosylation (SNO). TRIM72 is a cardioprotective membrane repair protein that can be both activated and targeted for degradation by different oxidative modifications. Consistent with the potential regulation of TRIM72 by various oxidative modifications, we found that SNO levels increased at C144 of TRIM72 with ischemic preconditioning. Therefore, to investigate the role of C144 in the regulation of TRIM72 function, we mutated C144 of TRIM72 to a serine residue (TRIM72(C144S)), and expressed either TRIM72(WT) or TRIM72(C144S) in HEK-293 cells, which lack endogenous TRIM72, in order to examine the effect of this mutation on the functional stability of TRIM72 and on cell survival. We hypothesized that SNO of TRIM72 stabilizes the protein, thus allowing for membrane repair and enhanced cell survival. Upon treatment with hydrogen peroxide (H2O2), we found that TRIM72(WT) levels were decreased, but not TRIM72(C144S) and this correlated with increased H2O2-induced cell death in TRIM72(WT) cells. Additionally, we found that treatment with the cardioprotective S-nitrosylating agent S-nitrosoglutathione (GSNO), was able to preserve TRIM72(WT) protein levels and enhance TRIM72(WT)-mediated cell survival, but had no effect on TRIM72(C144S) levels. Consistent with our hypothesis, GSNO was also found to increase SNO levels and inhibit H2O2-induced irreversible oxidation for TRIM72(WT) without affecting TRIM72(C144S). In further support of our hypothesis, GSNO blocked the ischemia/reperfusion-induced decrease in TRIM72 levels and reduced infarct size in a Langendorff-perfused heart model. The results of these studies have important implications for cardioprotection and suggest that

  18. Aircraft interior noise models - Sidewall trim, stiffened structures, and cabin acoustics with floor partition

    Science.gov (United States)

    Pope, L. D.; Wilby, E. G.; Willis, C. M.; Mayes, W. H.

    1983-01-01

    As part of the continuing development of an aircraft interior noise prediction model, in which a discrete modal representation and power flow analysis are used, theoretical results are considered for inclusion of sidewall trim, stiffened structures, and cabin acoustics with floor partition. For validation purposes, predictions of the noise reductions for three test articles (a bare ring-stringer stiffened cylinder, an unstiffened cylinder with floor and insulation, and a ring-stringer stiffened cylinder with floor and sidewall trim) are compared with measurements.

  19. Laser Trimming of CuAlMo Thin-Film Resistors: Effect of Laser Processing Parameters

    Science.gov (United States)

    Birkett, Martin; Penlington, Roger

    2012-08-01

    This paper reports the effect of varying laser trimming process parameters on the electrical performance of a novel CuAlMo thin-film resistor material. The films were prepared on Al2O3 substrates by direct-current (DC) magnetron sputtering, before being laser trimmed to target resistance value. The effect of varying key laser parameters of power, Q-rate, and bite size on the resistor stability and tolerance accuracy were systematically investigated. By reducing laser power and bite size and balancing this with Q-rate setting, significant improvements in resistor stability and resistor tolerance accuracies of less than ±0.5% were achieved.

  20. tclust: An R Package for a Trimming Approach to Cluster Analysis

    Directory of Open Access Journals (Sweden)

    2012-04-01

    Full Text Available Outlying data can heavily influence standard clustering methods. At the same time, clustering principles can be useful when robustifying statistical procedures. These two reasons motivate the development of feasible robust model-based clustering approaches. With this in mind, an R package for performing non-hierarchical robust clustering, called tclust, is presented here. Instead of trying to “fit” noisy data, a proportion α of the most outlying observations is trimmed. The tclust package efficiently handles different cluster scatter constraints. Graphical exploratory tools are also provided to help the user make sensible choices for the trimming proportion as well as the number of clusters to search for.

  1. The ability of White Leghorn hens with trimmed comb and wattles to thermoregulate.

    Science.gov (United States)

    Al-Ramamneh, D S; Makagon, M M; Hester, P Y

    2016-08-01

    It is estimated that each year over 19 million pullets in the United States have their combs partially trimmed at a young age to improve egg production and feed efficiency. A possible disadvantage of trimming is that the comb and wattles may be essential for thermoregulation during hot weather allowing for conductive cooling of the blood through vasodilation of superficial vessels in these integumentary tissues. The objective of this study was to investigate the effects of partial comb and wattle removal, performed at 21 d of age, on the ability of White Leghorns to thermoregulate before, during, and after an imposed heating episode that averaged 34.6°C for 50.5 h. An increase in mortality at 20 h and body temperature at 48 h post initiation of the heating episode demonstrated that hens with trimmed comb and wattles were not able to cope with heat stress as effectively as controls. The increase in wattle temperature in controls as compared to trimmed hens during the heating episode and following heat stress provides supportive evidence that blood pools to the peripheral surface for conductive heat loss. During high temperatures typical of summer, trimmed hens attempted to compensate for their lack of ability to transfer heat from their comb and wattles to the environment through increased proportion of panting and wing spreading. Under less extreme conditions with lowered ambient temperatures, the trimming of the comb and wattles did not impair the ability of hens to thermoregulate, as body temperatures and behavior were similar to controls with no mortality. Egg weight was the only production parameter adversely affected by the trimming of the comb and wattles as compared to controls. The implication is that hens need their combs and wattles to thermoregulate effectively during periods of high environmental temperature. Pullets should not be subjected to a comb and wattle trim if they are housed in laying facilities that are not appropriately cooled during the

  2. The effect of routine hoof trimming on locomotion score, ruminating time, activity and milk yield of dairy cows

    NARCIS (Netherlands)

    Hertem, van T.; Parmet, Y.; Steensels, M.; Maltz, E.; Antler, A.; Schlageter Tello, A.A.; Lokhorst, C.; Romanini, C.E.B.; Viazzi, S.; Bahr, C.; Berckmans, D.; Halachmi, I.

    2014-01-01

    The objective of this study was to quantify the effect of hoof trimming on cow behavior (ruminating time, activity, and locomotion score) and performance (milk yield) over time. Data were gathered from a commercial dairy farm in Israel where routine hoof trimming is done by a trained hoof trimmer

  3. The effect of preventive trimming on weight bearing and force balance on the claws of dairy cattle

    NARCIS (Netherlands)

    Tol, van der P.P.J.; Beek, van der S.S.; Metz, J.H.M.; Noordhuizen-Stassen, E.N.; Back, E.; Braam, C.R.; Weijs, W.A.

    2004-01-01

    Claw disorders and lameness in dairy cattle are an increasing problem of the modern dairy industry. To prevent claw disorders from evolving from the subclinical to the clinical stage, trimming is the management practice most routinely applied. The goal of preventive trimming (Toussaint-Raven method)

  4. Expression of TRIM28 correlates with proliferation and Bortezomib-induced apoptosis in B-cell non-Hodgkin lymphoma.

    Science.gov (United States)

    Zhang, Pei-Pei; Ding, Da-Zhi; Shi, Bing; Zhang, Shu-Qing; Gu, Ling-Li; Wang, Yu-Chan; Cheng, Chun

    2018-03-23

    Tripartite motif containing 28 (TRIM28) as a transcriptional co-repressor has been reported playing a role in regulating DNA damage response (DDR), cell differentiation, immune response, and tumorigenesis. The present study was performed to explore the biological function and clinical significance of TRIM28 in B-cell non-Hodgkin lymphoma (B-NHL). Results of the study displayed that high expression of TRIM28 was positively associated with the poorer survival of B-NHL patients as an independent prognostic factor. In addition, TRIM28 could promote the B-NHL cells proliferation through modulating cell cycle progression. The change of cyclinA, P21, and PCNA expression after TRIM28 expression modified further illustrated the mechanism in which TRIM28 participated in cell proliferation progression. Moreover, inhibition TRIM28 expression in B-NHL cells enhanced the sensibility to Bortezomib by regulating p53-mediated apoptosis pathway. Taken together, the present study showed that TRIM28 functions as a tumor promoter in B-NHL and may be a novel target for drug resistance to Bortezomib.

  5. TRIM29 Overexpression Promotes Proliferation and Survival of Bladder Cancer Cells through NF-κB Signaling.

    Science.gov (United States)

    Tan, Shu-Tao; Liu, Sheng-Ye; Wu, Bin

    2016-10-01

    TRIM29 overexpression has been reported in several human malignancies and showed correlation with cancer cell malignancy. The aim of the current study is to examine its clinical significance and biological roles in human bladder cancer tissues and cell lines. A total of 102 cases of bladder cancer tissues were examined for TRIM29 expression by immunohistochemistry. siRNA and plasmid transfection were performed in 5637 and BIU-87 cell lines. Cell Counting Kit-8, flow cytometry, western blot, and real-time polymerase chain reaction were performed to examine its biological roles and mechanism in bladder cancer cells. We found that TRIM29 overexpression showed correlation with invading depth (p=0.0087). Knockdown of TRIM29 expression in bladder cancer cell line 5637 inhibited cell growth rate and cell cycle transition while its overexpression in BIU-87 cells accelerated cell proliferation and cell cycle progression. TRIM29 overexpression also inhibited cell apoptosis induced by cisplatin. In addition, we demonstrated that TRIM29 depletion decreased while its overexpression led to upregulated expression of cyclin D1, cyclin E, and Bcl-2. We also showed that TRIM29 knockdown inhibited protein kinase C (PKC) and nuclear factor κB (NF-κB) signaling while its overexpression stimulated the PKC and NF-κB pathways. BAY 11-7082 (NF-κB inhibitor) partly attenuated the effect of TRIM29 on expression of cyclin and Bcl-2. Treatment with PKC inhibitor staurosporine resulted in ameliorated TRIM29 induced activation of NF-κB. The current study demonstrated that TRIM29 upregulates cyclin and Bcl family proteins level to facilitate malignant cell growth and inhibit drug-induced apoptosis in bladder cancer, possibly through PKC-NF-κB signaling pathways.

  6. Sample Size Determination for One- and Two-Sample Trimmed Mean Tests

    Science.gov (United States)

    Luh, Wei-Ming; Olejnik, Stephen; Guo, Jiin-Huarng

    2008-01-01

    Formulas to determine the necessary sample sizes for parametric tests of group comparisons are available from several sources and appropriate when population distributions are normal. However, in the context of nonnormal population distributions, researchers recommend Yuen's trimmed mean test, but formulas to determine sample sizes have not been…

  7. Application of a Broadband Active Vibration Control System to a Helicopter Trim Panel

    Science.gov (United States)

    Cabell, Randolph H.; Schiller, Noah H.; Simon, Frank

    2013-01-01

    This paper discusses testing of a broadband active vibration control concept on an interior trim panel in a helicopter cabin mockup located at ONERA's Centre de Toulouse. The control system consisted of twelve diamond-shaped piezoelectric actuators distributed around a 1.2m x 1.2m trim panel. Accelerometers were mounted at the four vertices of each diamond. The aspect ratio of the diamond was based on the dielectric constants of the piezoelectric material in order to create an actuator-sensor pair that was collocated over a broad frequency range. This allowed robust control to be implemented using simple, low power analog electronics. Initial testing on a thick acrylic window demonstrated the capability of the controller, but actuator performance was less satisfactory when mounted on a composite sandwich trim panel. This may have been due to the orthotropic nature of the trim panel, or due to its much higher stiffness relative to the acrylic window. Insights gained from a finite element study of the actuator-sensor-structural system are discussed.

  8. Introducing trimming and function ranking to Solid Works based on function analysis

    NARCIS (Netherlands)

    Chechurin, Leonid S.; Wits, Wessel Willems; Bakker, Hans M.; Cascini, G.; Vaneker, Thomas H.J.

    2011-01-01

    TRIZ based Function Analysis models existing products based on functional interactions between product parts. Such a function model description is the ideal starting point for product innovation. Design engineers can apply (TRIZ) methods such as trimming and function ranking to this function model

  9. Introducing Trimming and Function Ranking to SolidWorks based on Function Analysis

    NARCIS (Netherlands)

    Chechurin, L.S.; Wits, Wessel Willems; Bakker, Hans M.; Vaneker, Thomas H.J.

    2015-01-01

    TRIZ based Function Analysis models existing products based on functional interactions between product parts. Such a function model description is the ideal starting point for product innovation. Design engineers can apply (TRIZ) methods such as trimming and function ranking to this function model

  10. Mountain Plains Learning Experience Guide: Electrical Wiring. Course: Electrical Wiring Trim-Out.

    Science.gov (United States)

    Arneson, R.; And Others

    One of two individualized courses included in an electrical wiring curriculum, this course covers electrical materials installation for the trim-out stage. The course is comprised of five units: (1) Outlets, (2) Fixtures, (3) Switches, (4) Appliances, and (5) Miscellaneous. Each unit begins with a Unit Learning Experience Guide that gives…

  11. The influence of fat score and fat trimming on primal cut composition ...

    African Journals Online (AJOL)

    The objectives of this study were to evaluate the primal cut composition of South African lamb carcasses with different fat scores, and to identify cuts suitable for fat trimming. Sixty grain fed Dorper lambs (rams and ewes) were divided into three groups and slaughtered at 30, 36 and 42 kg. Chilled carcass sides were ...

  12. Glucosidase trimming inhibitors preferentially perturb T cell activation induced by CD2 mAb

    NARCIS (Netherlands)

    van Kemenade, F. J.; Rotteveel, F. T.; van den Broek, L. A.; Baars, P. A.; van Lier, R. A.; Miedema, F.

    1994-01-01

    Glycosidase trimming inhibitors may be used to study contribution of N-linked glycan moieties in T cell function. We have studied the effects of castanospermine (Cas), swainsonine (Swain), 1-deoxynojirimycin (dNM), and 1-deoxymannojirimycin (dMM) on T cell activation and differentiation. Our

  13. Genetic parameters for claw disorders and the effect of preselecting cows for trimming

    NARCIS (Netherlands)

    Spek, van der D.; Arendonk, van J.A.M.; Vallee, A.A.A.; Bovenhuis, H.

    2013-01-01

    Abstract Claw disorders are important traits relevant to dairy cattle breeding from an economical and welfare point of view. Selection for reduced claw disorders can be based on hoof trimmer records. Typically, not all cows in a herd are trimmed. Our objectives were to estimate heritabilities and

  14. Scoring of digital dermatitis during milking as an alternative to scoring in a hoof trimming chute

    DEFF Research Database (Denmark)

    Thomsen, Peter; Klaas, Ilka Christine; Bach, K.

    2008-01-01

    Digital dermatitis is a serious problem in dairy production in many countries. In many settings, it is important to evaluate the digital dermatitis status of individual cows or an entire dairy herd. Such an evaluation has traditionally been done in a hoof trimming chute. An evaluation in the milk......Digital dermatitis is a serious problem in dairy production in many countries. In many settings, it is important to evaluate the digital dermatitis status of individual cows or an entire dairy herd. Such an evaluation has traditionally been done in a hoof trimming chute. An evaluation...... in the milking parlor can take place without disturbing the cows to a large extent, it can be done using less labor compared with an evaluation in a hoof trimming chute, and is cheaper than using a chute. The objective was to evaluate the sensitivity and specificity of a rapid screening method for digital...... dermatitis in the milking parlor, without using any specialized tools and taking approximately 15 s/cow. All lactating cows in 3 commercial Danish dairy herds were included. Cows were first scored for the presence of digital dermatitis during milking and the next day all cows were scored during hoof trimming...

  15. Limit law of the iterated logarithm for B-valued trimmed sums

    Indian Academy of Sciences (India)

    Limit law of the iterated logarithm for B-valued trimmed sums. KE-ANG FU1, YUYANG QIU1,∗ and YELING TONG2. 1School of Statistics and Mathematics, Zhejiang Gongshang University,. Hangzhou 310018, China. 2Zhejiang Institute of Traditional Chinese Medicine, Hangzhou 310028, China. *Corresponding author.

  16. Limit law of the iterated logarithm for B-valued trimmed sums

    Indian Academy of Sciences (India)

    Annual Meetings · Mid Year Meetings · Discussion Meetings · Public Lectures · Lecture Workshops · Refresher Courses · Symposia · Live Streaming. Home; Journals; Proceedings – Mathematical Sciences; Volume 125; Issue 2. Limit law of the iterated logarithm for -valued trimmed sums. Ke-Ang Fu Yuyang Qiu Yeling ...

  17. Sensitivity of TRIM projections to management, harvest, yield, and stocking adjustment assumptions.

    Science.gov (United States)

    Susan J. Alexander

    1991-01-01

    The Timber Resource Inventory Model (TRIM) was used to make several projections of forest industry timber supply for the Douglas-fir region. The sensitivity of these projections to assumptions about management and yields is discussed. A base run is compared to runs in which yields were altered, stocking adjustment was eliminated, harvest assumptions were changed, and...

  18. Automotive Body Trim and Glass; Automotive Mechanics 2: 9045.05.

    Science.gov (United States)

    Dade County Public Schools, Miami, FL.

    This document presents an outline for a 135-hour course designed to help students become employable with skills, knowledge, attitudes, and values necessary for performing the required service of the automotive trim and glass mechanic. The course of study includes an orientation to the course, service tools and bench skills development, and a study…

  19. Some aspects of Trim-algorithm modernization for Monte-Carlo method

    International Nuclear Information System (INIS)

    Dovnar, S.V.; Grigor'ev, V.V.; Kamyshan, M.A.; Leont'ev, A.V.; Yanusko, S.V.

    2001-01-01

    Some aspects of Trim-algorithm modernization in Monte-Carlo method are discussed. This modification permits to raise the universality of program work with various potentials of ion-atom interactions and to improve the calculation precision for scattering angle θ c

  20. Evaluation of beef trim sampling methods for detection of Shiga toxin-producing Escherichia coli (STEC)

    Science.gov (United States)

    Presence of Shiga toxin-producing Escherichia coli (STEC) is a major concern in ground beef. Several methods for sampling beef trim prior to grinding are currently used in the beef industry. The purpose of this study was to determine the efficacy of the sampling methods for detecting STEC in beef ...

  1. Influence of tumbling, tumbling time, trim and sodium tripolyphosphate on quality and yield of cured hams

    NARCIS (Netherlands)

    Krause, R.J.; Ockerman, H.W.; Krol, B.; Moerman, P.C.; et al.

    1978-01-01

    Forty‐four boneless, cured hams were assigned to treatment groups to study the effect of tumbling, tumbling time (18 hr intermittent, 9.5 hr intermittent, 3 hr continuous), tumbling temperature (5°C and 15°C), sodium tripolyphosphate (TPP) pickle level (0 and 3.3%), and trim (lean, regular, and fat)

  2. Construction and assembling of the trim coils for the Milan superconducting cyclotron

    International Nuclear Information System (INIS)

    Baccaglioni, G.; Cartegni, G.C.; Fusetti, M.; Gini, L.; Grilli, L.

    1986-01-01

    This paper presents the main characteristics of the trim coils realized for the heavy ions superconducting cyclotron under construction at the Milan University. The guidelines in the choice of the conductor size, of the insulation and cooling parameters are discussed in some details. The main operations in the coils construction, as winding, impregnation, electrical tests and assembling, are described

  3. The Norwegian Emission Inventory 2012. Documentation of methodologies for estimating emissions of greenhouse gases and long-range transboundary air pollutants

    Energy Technology Data Exchange (ETDEWEB)

    Sandmo, Trond (ed.)

    2012-07-01

    The Norwegian emission inventory is a joint undertaking between the Climate and Pollution Agency1 and Statistics Norway. Statistics Norway is responsible for the collection and development of activity data, and emission figures are derived from models operated by Statistics Norway. The Climate and Pollution Agency is responsible for the emission factors, for providing data from specific industries and sources and for considering the quality, and assuring necessary updating, of emission models like, e.g., the road traffic model and calculation of methane emissions from landfills. Emission data are used for a range of national applications and for international reporting. The Climate and Pollution Agency is responsible for the Norwegian reporting to United Nations Framework Convention on Climate Change (UNFCCC) and to United Nations Economic Commission Europe (UN-ECE). This report documents the methodologies used in the Norwegian emission inventory of greenhouse gases (GHG), acidifying pollutants, heavy metals (HM) and persistent organic pollutants (POPs). The documentation will also serve as a part of the National Inventory Report submitted by Norway to the United Nations Framework Convention on Climate Change (UNFCCC), and as documentation of the reported emissions to UNECE for the pollutants restricted by CLRTAP (Convention on Long-Range Transboundary Air Pollution). LULUCF (land use, land-use change and forestry) is not considered in this report, see the National Inventory Report (Climate and Pollution Agency 2012) for documentation on this topic.This report replaces the previous documentation of the emission model (Sandmo 2011), and is the latest annually updated version of a report edited by Britta Hoem in 2005. The most important changes since last year's documentation are: Minor NOx emissions from production of rock wool, which previously not have been estimated, have been included, Some factors for estimation of N2O from agriculture have been altered

  4. The Norwegian Emission Inventory 2012. Documentation of methodologies for estimating emissions of greenhouse gases and long-range transboundary air pollutants

    Energy Technology Data Exchange (ETDEWEB)

    Sandmo, Trond [ed.

    2012-07-01

    The Norwegian emission inventory is a joint undertaking between the Climate and Pollution Agency1 and Statistics Norway. Statistics Norway is responsible for the collection and development of activity data, and emission figures are derived from models operated by Statistics Norway. The Climate and Pollution Agency is responsible for the emission factors, for providing data from specific industries and sources and for considering the quality, and assuring necessary updating, of emission models like, e.g., the road traffic model and calculation of methane emissions from landfills. Emission data are used for a range of national applications and for international reporting. The Climate and Pollution Agency is responsible for the Norwegian reporting to United Nations Framework Convention on Climate Change (UNFCCC) and to United Nations Economic Commission Europe (UN-ECE). This report documents the methodologies used in the Norwegian emission inventory of greenhouse gases (GHG), acidifying pollutants, heavy metals (HM) and persistent organic pollutants (POPs). The documentation will also serve as a part of the National Inventory Report submitted by Norway to the United Nations Framework Convention on Climate Change (UNFCCC), and as documentation of the reported emissions to UNECE for the pollutants restricted by CLRTAP (Convention on Long-Range Transboundary Air Pollution). LULUCF (land use, land-use change and forestry) is not considered in this report, see the National Inventory Report (Climate and Pollution Agency 2012) for documentation on this topic.This report replaces the previous documentation of the emission model (Sandmo 2011), and is the latest annually updated version of a report edited by Britta Hoem in 2005. The most important changes since last year's documentation are: Minor NOx emissions from production of rock wool, which previously not have been estimated, have been included, Some factors for estimation of N2O from agriculture have been altered, The

  5. [Tripartite motif-containing protein 34 (TRIM34) colocalized with micronuclei chromosome and hampers its movement to equatorial plate during the metaphase stage of mitosis].

    Science.gov (United States)

    Sun, Dakang; An, Xinye; Ji, Bing; Cheng, Yanli; Gao, Honglian; Tian, Mingming

    2016-06-01

    Objective To examine whether tripartite motif-containing protein 34 (TRIM34) is colocalized with micronuclei and investigate the influence on the movement of micronuclei chromosome in mitosis. Methods The eukaryotic expression vector TRIM34-pEGFP-N3 was constructed, identified and then transfected into HEK293T cells. With 4', 6-diamidino-2-phenylindole 2HCI (DAPI) staining, the colocalization between TRIM34 and micronuclei was observed under a fluorescence microscope. Moreover, MitoTracker(R)Deep Red was used to identify the colocalization between the complex of TRIM34-micronulei and mitochondria under a confocal microscope. Finally, the effect of TRIM34 on the movement of micronuclei chromosome in mitosis was examined. Results DNA sequencing confirmed that the vector TRIM34-pEGFP-N3 was constructed successfully. A fluorescence microscope revealed that TRIM34 could be colocalized with micronuclei in HEK293T cells transfected with TRIM34-pEGFP-N3. In the same manner, a confocal microscope distinctly showed that TRIM34 was colocalized with micronuclei similarly in appearance. However, there was no distinguished colocalization relationship between the complex of TRIM34-micronulei and mitochondria. Interestingly, the micronuclei chromosome conjugated with TRIM34 was hardly transferred to equatorial plate during the metaphase stage of mitosis. Conclusion TRIM34 is colocalized with micronuclei chromosome and hampers its movement to equatorial plate in mitosis.

  6. Lead intoxication in dogs: risk assessment of feeding dogs trimmings of lead-shot game.

    Science.gov (United States)

    Høgåsen, Helga R; Ørnsrud, Robin; Knutsen, Helle K; Bernhoft, Aksel

    2016-07-25

    Expanding lead-based bullets, commonly used for hunting of big game, produce a scattering of lead particles in the carcass around the wound channel. Trimmings around this channel, which are sometimes fed to dogs, may contain lead particles. The aim of this study was to assess potential health effects of feeding dogs such trimmings. Lead ingestion most commonly causes gastrointestinal and neurological clinical signs, although renal, skeletal, haematological, cardiovascular and biochemical effects have also been reported. Experimental data indicate that a daily dose of around 1 mg lead as lead acetate/kg body weight for ten days may be considered as a Lowest Observed Effect Level in dogs. Acute toxicity documentation from the Centers for Disease Control and Prevention indicates 300 mg/kg body weight as the lowest dose of lead acetate causing death in dogs after oral ingestion. Our assessment suggests that dogs fed trimmings of lead-shot game may be affected by the amounts of lead present, and that even deadly exposure could occasionally occur. The intestinal absorption of lead from bullets was assumed to be 10-80 % of that of lead acetate, reflecting both the variability in particle size and uncertainty about the bioavailability of metallic lead in dogs. Despite data gaps, this study indicates that feeding dogs trimmings of lead-shot game may represent a risk of lead intoxication. More research is needed to assess the exact consequences, if lead-based bullets are still to be used. Meanwhile, we recommend that trimmings close to the wound channel should be made inaccessible to dogs, as well as to other domestic or wild animals.

  7. Trim9 Deletion Alters the Morphogenesis of Developing and Adult-Born Hippocampal Neurons and Impairs Spatial Learning and Memory.

    Science.gov (United States)

    Winkle, Cortney C; Olsen, Reid H J; Kim, Hyojin; Moy, Sheryl S; Song, Juan; Gupton, Stephanie L

    2016-05-04

    During hippocampal development, newly born neurons migrate to appropriate destinations, extend axons, and ramify dendritic arbors to establish functional circuitry. These developmental stages are recapitulated in the dentate gyrus of the adult hippocampus, where neurons are continuously generated and subsequently incorporate into existing, local circuitry. Here we demonstrate that the E3 ubiquitin ligase TRIM9 regulates these developmental stages in embryonic and adult-born mouse hippocampal neurons in vitro and in vivo Embryonic hippocampal and adult-born dentate granule neurons lacking Trim9 exhibit several morphological defects, including excessive dendritic arborization. Although gross anatomy of the hippocampus was not detectably altered by Trim9 deletion, a significant number of Trim9(-/-) adult-born dentate neurons localized inappropriately. These morphological and localization defects of hippocampal neurons in Trim9(-/-) mice were associated with extreme deficits in spatial learning and memory, suggesting that TRIM9-directed neuronal morphogenesis may be involved in hippocampal-dependent behaviors. Appropriate generation and incorporation of adult-born neurons in the dentate gyrus are critical for spatial learning and memory and other hippocampal functions. Here we identify the brain-enriched E3 ubiquitin ligase TRIM9 as a novel regulator of embryonic and adult hippocampal neuron shape acquisition and hippocampal-dependent behaviors. Genetic deletion of Trim9 elevated dendritic arborization of hippocampal neurons in vitro and in vivo Adult-born dentate granule cells lacking Trim9 similarly exhibited excessive dendritic arborization and mislocalization of cell bodies in vivo These cellular defects were associated with severe deficits in spatial learning and memory. Copyright © 2016 the authors 0270-6474/16/364940-19$15.00/0.

  8. Genome-wide association study for claw disorders and trimming status in dairy cattle.

    Science.gov (United States)

    van der Spek, D; van Arendonk, J A M; Bovenhuis, H

    2015-02-01

    Performing a genome-wide association study (GWAS) might add to a better understanding of the development of claw disorders and the need for trimming. Therefore, the aim of the current study was to perform a GWAS on claw disorders and trimming status and to validate the results for claw disorders based on an independent data set. Data consisted of 20,474 cows with phenotypes for claw disorders and 50,238 cows with phenotypes for trimming status. Recorded claw disorders used in the current study were double sole (DS), interdigital hyperplasia (IH), sole hemorrhage (SH), sole ulcer (SU), white line separation (WLS), a combination of infectious claw disorders consisting of (inter-)digital dermatitis and heel erosion, and a combination of laminitis-related claw disorders (DS, SH, SU, and WLS). Of the cows with phenotypes for claw disorders, 1,771 cows were genotyped and these cow data were used for the GWAS on claw disorders. A SNP was considered significant when the false discovery rate≤0.05 and suggestive when the false discovery rate≤0.20. An independent data set of 185 genotyped bulls having at least 5 daughters with phenotypes (6,824 daughters in total) for claw disorders was used to validate significant and suggestive SNP detected based on the cow data. To analyze the trait "trimming status" (i.e., the need for claw trimming), a data set with 327 genotyped bulls having at least 5 daughters with phenotypes (18,525 daughters in total) was used. Based on the cow data, in total 10 significant and 45 suggestive SNP were detected for claw disorders. The 10 significant SNP were associated with SU, and mainly located on BTA8. The suggestive SNP were associated with DS, IH, SU, and laminitis-related claw disorders. Three of the suggestive SNP were validated in the data set of 185 bulls, and were located on BTA13, BTA14, and BTA17. For infectious claw disorders, SH, and WLS, no significant or suggestive SNP associations were detected. For trimming status, 1 significant

  9. Comparison of some properties of four provisional restorations resin: Trim, Tempron, Acropars TRII & Duralay (Aria Dent

    Directory of Open Access Journals (Sweden)

    Monzavi A.

    2006-08-01

    Full Text Available Background and Aim: Use of provisional restorations is one of the important phases in the treatment of patients who need fixed prosthesis. Some physical properties are required for these materials. The purpose of this study was the comparison of some physical properties of 4 kinds of resins: Trim, Tempron, Duralay (Aria Dent and Acropars TRII. Materials and Methods: In this experimental study, transverse-strength (TS, setting time (ST, polymerization shrinkage (PS and temperature rise (TR during polymerization were tested. In transverse strength test, 5 samples of each resin were made. TS testing was done with an Instron testing machine. ST testing (5 samples in each group was done with Gilmore needle. In PS test, 11 cylindric samples were prepared from each resin and the shrinkage was examined with digital micrometer (up to 24 hours. In TR test, after mixing the powder and liquid of resins (8 samples in each group, the temperature rise was recorded with 10 seconds interval (up to 15 minutes. Data were analyzed with one-way ANOVA and Tukey HSD tests with p<0.05 as the limit of significance. Results: In TS test, all samples of Trim were bent and no fracture was observed, while Tempron and Duralay showed no significant difference. Both Tempron and Duralay revealed high significant difference with Acropars TRII (P <0.01. In ST test, the difference between groups was significant (P<0.01. The lowest ST was observed in Acropars TRII (7 min, and the highest in Tempron (9.53 min. In PS test, significant difference was observed between Trim and Acropars TRII (P<0.01. PS was completed after 120 min in Tempron and Trim groups. However, PS continued to increase in other groups. In TR test, the difference between groups was significant (P<0.05. Duralay showed the highest TR and the lowest was seen in Trim. Conclusion: In this study, Trim showed better properties than other studied groups. Acropars TRII had the lowest strength. The highest temperature rise

  10. [METHODOLOGY FOR THE ASSESSMENT OF THE IMPACT OF THE ATMOSPHERIC AIR POLLUTION ON THE FORMATION OF THE LEVELS OF OVERALL MORBIDITY RATE OF BRONCHIAL ASTHMA].

    Science.gov (United States)

    Veremchuk, L V; Cherpack, N A; Gvozdenko, T A; Volkova, M V

    2015-01-01

    In large cities with strong air pollution the formation of the levels of morbidity rate of bronchial asthma has a complex causation that requires the search for informative methods for identification of causes and consequences of this dependence. Method for the assessment of the dependence of overall levels of morbidity rate of bronchial asthma on the degree of air pollution allows you to select a "useful information" of the direct impact of air pollution on a background of random processes and latent relationship between human and environment. The use of the method of the information entropy analysis allowed us to estimate the total and the individual contribution of the separate components of air pollution on the formation of levels of total morbidity rate of bronchial asthma in the population of the city of Vladivostok. Levels of total incidence of this pathology were established to differ in various age groups. The adult population is more adapted to air pollution, but retains a high sensitivity to the impact of nitrogen dioxide. Levels of overall l morbidity rate of bronchial asthma in children and adolescents depend on the total air pollution with some dominance of the influence of suspended matter and carbon monoxide.

  11. The Formulation of Binding Agent Concentration on Raw Restructured Goat Meat Trimming Product

    Directory of Open Access Journals (Sweden)

    Rini Mastuti

    2012-02-01

    Full Text Available The utilization of raw materials and formulation method would affect the quality of the processed meat product. Therefore, a research on the processing method to produce a raw structured product should be conducted. The research was testing a single factor comprises of following parameters: control (without binding agent; 0.3%, 0.5% and 0.7% sodium alginat and 0.3%, 0.5% and 0.7% carragenan, respectively. The results showed that the goat meat trimming could be used as raw materials in the production of the best restructured meat using 0.5% carragenan. This raw restructured meat produced had a loss weight of 1.67%, pH value  7.89, WHC  48.345, and moisture content  75.20%.   Keywords : sodium alginat, carragenan, raw restructured goat meat trimming.

  12. Investigation Of Adhesion Formation In New Stainless Steel Trim Spring Operated Pressure Relief Valves

    Energy Technology Data Exchange (ETDEWEB)

    Gross, Robert E. [Savannah River Site (SRS), Aiken, SC (United States); Bukowski, Julia V. [Villanova University, Villanova, PA (United States); Goble, William M. [exida, Sellersville, PA (United States)

    2013-04-16

    Examination of proof test data for new (not previously installed) stainless steel (SS) trim spring operated pressure relief valves (SOPRV) reveals that adhesions form between the seat and disc in about 46% of all such SOPRV. The forces needed to overcome these adhesions can be sufficiently large to cause the SOPRV to fail its proof test (FPT) prior to installation. Furthermore, a significant percentage of SOPRV which are found to FPT are also found to ''fail to open'' (FTO) meaning they would not relief excess pressure in the event of an overpressure event. The cases where adhesions result in FTO or FPT appear to be confined to SOPRV with diameters < 1 in and set pressures < 150 psig and the FTO are estimated to occur in 0.31% to 2.00% of this subpopulation of SS trim SOPRV. The reliability and safety implications of these finding for end-users who do not perform pre-installation testing of SOPRV are discussed.

  13. A trim-loss minimization in a produce-handling vehicle production plant

    Directory of Open Access Journals (Sweden)

    Apichai Ritvirool

    2007-01-01

    Full Text Available How to cut out the required pieces from raw materials by minimizing waste is a trim-loss problem. The integer linear programming (ILP model was developed to solve this problem. In addition, this ILPmodel could be used for planning an order over some future time period. Time horizon of ordering raw material including weekly, monthly, quarterly, and annually could be planned to reduce the trim loss. Thenumerical examples using an industrial case study of a produce-handling vehicle production plant were presented to illustrate how the proposed ILP model could be applied to actual systems and the types ofinformation that was obtained relative to implementation. The results showed that the proposed ILP model can be used as a decision support tool for selecting time horizon of order planning and cutting patterns todecrease material cost and waste from cutting raw material.

  14. The Host E3-Ubiquitin Ligase TRIM6 Ubiquitinates the Ebola Virus VP35 Protein and Promotes Virus Replication.

    Science.gov (United States)

    Bharaj, Preeti; Atkins, Colm; Luthra, Priya; Giraldo, Maria Isabel; Dawes, Brian E; Miorin, Lisa; Johnson, Jeffrey R; Krogan, Nevan J; Basler, Christopher F; Freiberg, Alexander N; Rajsbaum, Ricardo

    2017-09-15

    Ebola virus (EBOV), a member of the Filoviridae family, is a highly pathogenic virus that causes severe hemorrhagic fever in humans and is responsible for epidemics throughout sub-Saharan, central, and West Africa. The EBOV genome encodes VP35, an important viral protein involved in virus replication by acting as an essential cofactor of the viral polymerase as well as a potent antagonist of the host antiviral type I interferon (IFN-I) system. By using mass spectrometry analysis and coimmunoprecipitation assays, we show here that VP35 is ubiquitinated on lysine 309 (K309), a residue located on its IFN antagonist domain. We also found that VP35 interacts with TRIM6, a member of the E3-ubiquitin ligase tripartite motif (TRIM) family. We recently reported that TRIM6 promotes the synthesis of unanchored K48-linked polyubiquitin chains, which are not covalently attached to any protein, to induce efficient antiviral IFN-I-mediated responses. Consistent with this notion, VP35 also associated noncovalently with polyubiquitin chains and inhibited TRIM6-mediated IFN-I induction. Intriguingly, we also found that TRIM6 enhances EBOV polymerase activity in a minigenome assay and TRIM6 knockout cells have reduced replication of infectious EBOV, suggesting that VP35 hijacks TRIM6 to promote EBOV replication through ubiquitination. Our work provides evidence that TRIM6 is an important host cellular factor that promotes EBOV replication, and future studies will focus on whether TRIM6 could be targeted for therapeutic intervention against EBOV infection. IMPORTANCE EBOV belongs to a family of highly pathogenic viruses that cause severe hemorrhagic fever in humans and other mammals with high mortality rates (40 to 90%). Because of its high pathogenicity and lack of licensed antivirals and vaccines, EBOV is listed as a tier 1 select-agent risk group 4 pathogen. An important mechanism for the severity of EBOV infection is its suppression of innate immune responses. The EBOV VP35

  15. Evaluation of the UnTRIM model for 3-D tidal circulation

    Science.gov (United States)

    Cheng, R.T.; Casulli, V.; ,

    2001-01-01

    A family of numerical models, known as the TRIM models, shares the same modeling philosophy for solving the shallow water equations. A characteristic analysis of the shallow water equations points out that the numerical instability is controlled by the gravity wave terms in the momentum equations and by the transport terms in the continuity equation. A semi-implicit finite-difference scheme has been formulated so that these terms and the vertical diffusion terms are treated implicitly and the remaining terms explicitly to control the numerical stability and the computations are carried out over a uniform finite-difference computational mesh without invoking horizontal or vertical coordinate transformations. An unstructured grid version of TRIM model is introduced, or UnTRIM (pronounces as "you trim"), which preserves these basic numerical properties and modeling philosophy, only the computations are carried out over an unstructured orthogonal grid. The unstructured grid offers the flexibilities in representing complex study areas so that fine grid resolution can be placed in regions of interest, and coarse grids are used to cover the remaining domain. Thus, the computational efforts are concentrated in areas of importance, and an overall computational saving can be achieved because the total number of grid-points is dramatically reduced. To use this modeling approach, an unstructured grid mesh must be generated to properly reflect the properties of the domain of the investigation. The new modeling flexibility in grid structure is accompanied by new challenges associated with issues of grid generation. To take full advantage of this new model flexibility, the model grid generation should be guided by insights into the physics of the problems; and the insights needed may require a higher degree of modeling skill.

  16. UrQt: an efficient software for the Unsupervised Quality trimming of NGS data.

    Science.gov (United States)

    Modolo, Laurent; Lerat, Emmanuelle

    2015-04-29

    Quality control is a necessary step of any Next Generation Sequencing analysis. Although customary, this step still requires manual interventions to empirically choose tuning parameters according to various quality statistics. Moreover, current quality control procedures that provide a "good quality" data set, are not optimal and discard many informative nucleotides. To address these drawbacks, we present a new quality control method, implemented in UrQt software, for Unsupervised Quality trimming of Next Generation Sequencing reads. Our trimming procedure relies on a well-defined probabilistic framework to detect the best segmentation between two segments of unreliable nucleotides, framing a segment of informative nucleotides. Our software only requires one user-friendly parameter to define the minimal quality threshold (phred score) to consider a nucleotide to be informative, which is independent of both the experiment and the quality of the data. This procedure is implemented in C++ in an efficient and parallelized software with a low memory footprint. We tested the performances of UrQt compared to the best-known trimming programs, on seven RNA and DNA sequencing experiments and demonstrated its optimality in the resulting tradeoff between the number of trimmed nucleotides and the quality objective. By finding the best segmentation to delimit a segment of good quality nucleotides, UrQt greatly increases the number of reads and of nucleotides that can be retained for a given quality objective. UrQt source files, binary executables for different operating systems and documentation are freely available (under the GPLv3) at the following address: https://lbbe.univ-lyon1.fr/-UrQt-.html .

  17. Development and validation of the Treatment Related Impact Measure of Weight (TRIM-Weight

    Directory of Open Access Journals (Sweden)

    Lessard Suzanne

    2010-02-01

    Full Text Available Abstract Background The use of prescription anti-obesity medication (AOM is becoming increasingly common as treatment options grow and become more accessible. However, AOM may not be without a wide range of potentially negative impacts on patient functioning and well being. The Treatment Related Impact Measure (TRIM-Weight is an obesity treatment-specific patient reported outcomes (PRO measure designed to assess the key impacts of prescription anti-obesity medication. This paper will present the validation findings for the TRIM-Weight. Methods The online validation battery survey was administered in four countries (the U.S., U.K., Australia, and Canada. Eligible subjects were over age eighteen, currently taking a prescription AOM and were currently or had been obese during their life. Validation analyses were conducted according to an a priori statistical analysis plan. Item level psychometric and conceptual criteria were used to refine and reduce the preliminary item pool and factor analysis to identify structural domains was performed. Reliability and validity testing was then performed and the minimally importance difference (MID explored. Results Two hundred and eight subjects completed the survey. Twenty-one of the 43 items were dropped and a five-factor structure was achieved: Daily Life, Weight Management, Treatment Burden, Experience of Side Effects, and Psychological Health. A-priori criteria for internal consistency and test-retest coefficients for the total score and all five subscales were met. All pre-specified hypotheses for convergent and known group validity were also met with the exception of the domain of Daily Life (proven in an ad hoc analysis as well as the 1/2 standard deviation threshold for the MID. Conclusion The development and validation of the TRIM-Weight has been conducted according to well-defined principles for the creation of a PRO measure. Based on the evidence to date, the TRIM-Weight can be considered a brief

  18. Lichens biomonitoring as feasible methodology to assess air pollution in natural ecosystems: combined study of quantitative PAHs analyses and lichen biodiversity in the Pyrenees Mountains.

    Science.gov (United States)

    Blasco, María; Domeño, Celia; Nerín, Cristina

    2008-06-01

    The air quality in the Aragón valley, in the central Pyrenees, has been assessed by evaluation of lichen biodiversity and mapped by elaboration of the Index of Air Purity (IAP) based on observations of the presence and abundance of eight kinds of lichen with different sensitivity to air pollution. The IAP values obtained have been compared with quantitative analytical measures of 16 PAHs in the lichen Evernia prunastri, because this species was associated with a wide range of traffic exposure and levels of urbanization. Analyses of PAHs were carried out by the DSASE method followed by an SPE clean-up step and GC-MS analysis. The concentration of total PAHs found in lichen samples from the Aragón valley ranged from 692 to 6420 ng g(-1) and the PAHs profile showed predominance of compounds with three aromatic rings. The influence of the road traffic in the area has been shown because values over the median concentration of PAHs (>1092 ng g(-1)), percentage of combustion PAHs (>50%), and equivalent toxicity (>169) were found in lichens collected at places exposed to the influence of traffic. The combination of both methods suggests IAP as a general method for evaluating the air pollution referenced to PAHs because it can be correlated with the content of combustion PAHs and poor lichen biodiversity can be partly explained by the air pollution caused by specific PAHs.

  19. Severe trimming and enhanced competition of laterals as a tool to delay ripening in Tempranillo vineyards under semiarid conditions

    Directory of Open Access Journals (Sweden)

    Luis Gonzaga Santesteban

    2017-05-01

    Significance and impact of the study: this study proves the potentiality of the joint use of trimming and increased irrigation to delay ripening, although it is necessary to analyze the implications the obtained delay has on other quality aspects. The lower anthocyanin and phenolic values observed in trimmed vines were not solely due to delayed ripening, as lower values were observed even when data were compared for a given total soluble solid content.

  20. Building envelope design for renewal of air by natural ventilation in moderate climates. Proposition of a designing methodology; Conception des enveloppes de batiments pour le renouvellement d'air par ventilation naturelle en climats temperes. Proposition d'une methodologie de conception

    Energy Technology Data Exchange (ETDEWEB)

    Mansouri, Y.

    2003-12-01

    The subject of this research is to produce methods and methodological tools for the architects to support the integration of natural ventilation systems in the building envelope design. Our research is situated to the interface between the architectural practice and the physical research on natural ventilation. We are interested in phenomena that can influence or force the strategy of ventilation. A morphological analysis of naturally ventilated buildings concerning the integration modes of natural ventilation systems is done permitting US to propose a typology and a topology of ventilation systems. We define criteria in relation to the thermal comfort, to the quality of air and the economy of energy to assess air renewal techniques. In complement of the sizing tool, we elaborate a methodology of conception for the integration of passives ventilation systems. Design guidelines permit US to conclude on an effective natural ventilation system which is well adapted to collective habitat. (author)

  1. Resampling nucleotide sequences with closest-neighbor trimming and its comparison to other methods.

    Directory of Open Access Journals (Sweden)

    Kouki Yonezawa

    Full Text Available A large number of nucleotide sequences of various pathogens are available in public databases. The growth of the datasets has resulted in an enormous increase in computational costs. Moreover, due to differences in surveillance activities, the number of sequences found in databases varies from one country to another and from year to year. Therefore, it is important to study resampling methods to reduce the sampling bias. A novel algorithm-called the closest-neighbor trimming method-that resamples a given number of sequences from a large nucleotide sequence dataset was proposed. The performance of the proposed algorithm was compared with other algorithms by using the nucleotide sequences of human H3N2 influenza viruses. We compared the closest-neighbor trimming method with the naive hierarchical clustering algorithm and [Formula: see text]-medoids clustering algorithm. Genetic information accumulated in public databases contains sampling bias. The closest-neighbor trimming method can thin out densely sampled sequences from a given dataset. Since nucleotide sequences are among the most widely used materials for life sciences, we anticipate that our algorithm to various datasets will result in reducing sampling bias.

  2. A proposed methodology for impact assessment of air quality traffic-related measures: The case of PM2.5 in Beijing.

    Science.gov (United States)

    Fontes, Tânia; Li, Peilin; Barros, Nelson; Zhao, Pengjun

    2018-08-01

    Air quality traffic-related measures have been implemented worldwide to control the pollution levels of urban areas. Although some of those measures are claiming environmental improvements, few studies have checked their real impact. In fact, quantitative estimates are often focused on reducing emissions, rather than on evaluating the actual measures' effect on air quality. Even when air quality studies are conducted, results are frequently unclear. In order to properly assess the real impact on air quality of traffic-related measures, a statistical method is proposed. The method compares the pollutant concentration levels observed after the implementation of a measure with the concentration values of the previous year. Short- and long-term impact is assessed considering not only their influence on the average pollutant concentration, but also on its maximum level. To control the effect of the main confounding factors, only the days with similar environmental conditions are analysed. The changeability of the key meteorological variables that affect the transport and dispersion of the pollutant studied are used to identify and group the days categorized as similar. Resemblance of the pollutants' concentration of the previous day is also taken into account. The impact of the road traffic measures on the air pollutants' concentration is then checked for those similar days using specific statistical functions. To evaluate the proposed method, the impact on PM 2.5 concentrations of two air quality traffic-related measures (M1 and M2) implemented in the city of Beijing are taken into consideration: M1 was implemented in 2009, restricting the circulation of yellow-labelled vehicles, while M2 was implemented in 2014, restricting the circulation of heavy-duty vehicles. To compare the results of each measure, a time-period when these measures were not applied is used as case-control. Copyright © 2018 Elsevier Ltd. All rights reserved.

  3. Development and Operation of an Automatic Rotor Trim Control System for use During the UH-60 Individual Blade Control Wind Tunnel Test

    Science.gov (United States)

    Theodore, Colin R.

    2010-01-01

    A full-scale wind tunnel test to evaluate the effects of Individual Blade Control (IBC) on the performance, vibration, noise and loads of a UH-60A rotor was recently completed in the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel [1]. A key component of this wind tunnel test was an automatic rotor trim control system that allowed the rotor trim state to be set more precisely, quickly and repeatably than was possible with the rotor operator setting the trim condition manually. The trim control system was also able to maintain the desired trim condition through changes in IBC actuation both in open- and closed-loop IBC modes, and through long-period transients in wind tunnel flow. This ability of the trim control system to automatically set and maintain a steady rotor trim enabled the effects of different IBC inputs to be compared at common trim conditions and to perform these tests quickly without requiring the rotor operator to re-trim the rotor. The trim control system described in this paper was developed specifically for use during the IBC wind tunnel test

  4. Evaluation of sanitary impact of urban air pollution. Methodological guide.; Evaluation de l'impact sanitaire de la pollution atmospherique urbaine. Guide methodologique

    Energy Technology Data Exchange (ETDEWEB)

    Glorennec, Ph.; Nourry, L [Cellule Inter-Regionale d' Epidemiologie (France); Quenel, Ph. [Institut National de Veille Sanitaire, 94 - Saint Maurice (France)] [and others

    1999-07-01

    The institute of sanitary watch has setting up an epidemiological surveillance plan in nine french towns in order to quantify and to keep a close eye to the relations existing between the urban air pollution and the populations health.The method is detailed with its advantages and its limits. (N.C.)

  5. Collection methodology evaluation and solvents analysis/mixtures solvents in the air in work ambient: methanol in MEG mixture (methanol 33%, ethanol 60% and gasoline 7%); Avaliacao de metodologia de coleta e analise de solventes/misturas de solventes no ar em ambiente de trabalho: metanol em mistura MEG (metanol 33%, etanol 60% e gasolina 7%)

    Energy Technology Data Exchange (ETDEWEB)

    Cardoso, Luiza Maria Nunes

    1995-07-01

    This thesis presents a proposal for evaluation of collection and solvent/solvent mixtures analysis methodology for the air in the work environment by studying the following issues of present solvents: historical aspects; methanol - properties and toxicity; collection methodology evaluation, and gases and vapors analysis in the air; experimental data. The denominated mixture MEG - methanol, ethanol and gasoline is analyzed in terms of its chemical characteristics. The author concludes the work detaching that the methodology presented can only be used for short duration measurements in concentrations peaks studies.

  6. TRIMe7-CypA, an alternative splicing isoform of TRIMCyp in rhesus macaque, negatively modulates TRIM5α activity

    Energy Technology Data Exchange (ETDEWEB)

    Na, Lei [Harbin Veterinary Research Institute of the Chinese Academy of Agricultural Sciences, Harbin 150001 (China); Tang, Yan-Dong [Harbin Veterinary Research Institute of the Chinese Academy of Agricultural Sciences, Harbin 150001 (China); Biotechnology Institute of Southern Medical University, Guangzhou 510515 (China); Liu, Jian-Dong; Yu, Chang-Qing; Sun, Liu-Ke; Lin, Yue-Zhi; Wang, Xue-Feng [Harbin Veterinary Research Institute of the Chinese Academy of Agricultural Sciences, Harbin 150001 (China); Wang, Xiaojun, E-mail: xjw@hvri.ac.cn [Harbin Veterinary Research Institute of the Chinese Academy of Agricultural Sciences, Harbin 150001 (China); Zhou, Jian-Hua, E-mail: jianhua_uc@126.com [Harbin Veterinary Research Institute of the Chinese Academy of Agricultural Sciences, Harbin 150001 (China); Harbin Pharmaceutical Group Biovaccine Company, Harbin 150069 (China)

    2014-04-04

    Highlights: • TRIMe7-CypA expresses in rhesus and pig-tailed, but not long-tailed macaques. • TRIMe7-CypA does not show the restriction to a HIV-GFP report virus in vitro. • It acts as a negative modulator to TRIM5α likely by competitive inhibition. - Abstract: The existence of innate, host-specific restriction factors is a major obstacle to the development of nonhuman primate models for AIDS studies, and TRIM5α is one of the most important of these restriction factors. In recent years, a TRIM5 chimeric gene that was retrotransposed by a cyclophilin A (CypA) cDNA was identified in certain macaque species. The TRIM5α-CypA fusion protein, TRIMCyp, which was expressed in these monkeys, had lost its restriction ability toward HIV-1. We previously found that TRIMe7-CypA, an alternative splicing isoform of the TRIMCyp transcripts, was expressed in pig-tailed and rhesus macaques but absent in long-tailed macaques. In this study, the anti-HIV-1 activity of TRIMe7-CypA in the rhesus macaque (RhTRIMe7-CypA) was investigated. The over-expression of RhTRIMe7-CypA in CrFK, HeLa and HEK293T cells did not restrict the infection or replication of an HIV-1-GFP reporter virus in these cells. As a positive control, rhesus (rh)TRIM5α strongly inhibited the reporter virus. Intriguingly, the anti-HIV-1 activity of RhTRIM5α was significantly reduced in a dose-dependent manner by the co-repression of RhTRIMe7-CypA. Our data indicate that although the RhTRIMe7-CypA isoform does not appear to restrict HIV-1, it may act as a negative modulator of TRIM family proteins, presumably by competitive inhibition.

  7. TRIMe7-CypA, an alternative splicing isoform of TRIMCyp in rhesus macaque, negatively modulates TRIM5α activity

    International Nuclear Information System (INIS)

    Na, Lei; Tang, Yan-Dong; Liu, Jian-Dong; Yu, Chang-Qing; Sun, Liu-Ke; Lin, Yue-Zhi; Wang, Xue-Feng; Wang, Xiaojun; Zhou, Jian-Hua

    2014-01-01

    Highlights: • TRIMe7-CypA expresses in rhesus and pig-tailed, but not long-tailed macaques. • TRIMe7-CypA does not show the restriction to a HIV-GFP report virus in vitro. • It acts as a negative modulator to TRIM5α likely by competitive inhibition. - Abstract: The existence of innate, host-specific restriction factors is a major obstacle to the development of nonhuman primate models for AIDS studies, and TRIM5α is one of the most important of these restriction factors. In recent years, a TRIM5 chimeric gene that was retrotransposed by a cyclophilin A (CypA) cDNA was identified in certain macaque species. The TRIM5α-CypA fusion protein, TRIMCyp, which was expressed in these monkeys, had lost its restriction ability toward HIV-1. We previously found that TRIMe7-CypA, an alternative splicing isoform of the TRIMCyp transcripts, was expressed in pig-tailed and rhesus macaques but absent in long-tailed macaques. In this study, the anti-HIV-1 activity of TRIMe7-CypA in the rhesus macaque (RhTRIMe7-CypA) was investigated. The over-expression of RhTRIMe7-CypA in CrFK, HeLa and HEK293T cells did not restrict the infection or replication of an HIV-1-GFP reporter virus in these cells. As a positive control, rhesus (rh)TRIM5α strongly inhibited the reporter virus. Intriguingly, the anti-HIV-1 activity of RhTRIM5α was significantly reduced in a dose-dependent manner by the co-repression of RhTRIMe7-CypA. Our data indicate that although the RhTRIMe7-CypA isoform does not appear to restrict HIV-1, it may act as a negative modulator of TRIM family proteins, presumably by competitive inhibition

  8. Over-expression of TRIM37 promotes cell migration and metastasis in hepatocellular carcinoma by activating Wnt/β-catenin signaling

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Jianxin; Yu, Chao; Chen, Meiyuan; Tian, She; Sun, Chengyi, E-mail: chenyisun11@163.com

    2015-09-04

    Hepatocellular carcinoma (HCC) is the most common cancer in the world especially in East Asia and Africa. Advanced stage, metastasis and frequent relapse are responsible for the poor prognosis of HCC. However, the precise mechanisms underlying HCC remained unclear. So it is urgent to identify the pathological processes and relevant molecules of HCC. TRIM37 is an E3 ligase and has been observed deregulated expression in various tumors. Recent studies of TRIM37 have implicated that TRIM37 played critical roles in cell proliferation and other processes. In the present study, we demonstrated that TRIM37 expression was notably up-regulated in HCC samples and was associated with advanced stage and tumor volume, which all indicating the poor outcomes. We also found that TRIM37 could serve as an independent prognostic factor of HCC. During the course of in vitro and in vivo work, we showed that TRIM37 promoted HCC cells migration and metastasis by inducing EMT. Furthermore, we revealed that the effect of TRIM37 mediated EMT in HCC cells was achieved by the activation of Wnt/β-catenin signaling. These finding may provide insight into the understanding of TRIM37 as a novel critical factor of HCC and a candidate target for HCC treatment. - Highlights: • Highly expression of TRIM37 is found in HCC samples compared with nontumorous samples. • TRIM37 expression is correlated with advanced HCC stages and could be an independent prognostic factor. • TRIM37 promotes cell proliferation and metastasis. • We report an E3 ligase TRIM37 affects Wnt/β-catenin signaling.

  9. Public health benefits of reducing air pollution in Shanghai: a proof-of-concept methodology with application to BenMAP.

    Science.gov (United States)

    Voorhees, A Scott; Wang, Jiandong; Wang, Cuicui; Zhao, Bin; Wang, Shuxiao; Kan, Haidong

    2014-07-01

    In recent years, levels of particulate matter (PM) air pollution in China have been relatively high, exceeding China's Class II standards in many cities and impacting public health. This analysis takes Chinese health impact functions and underlying health incidence, applies 2010-2012 modeled and monitored PM air quality data, and estimates avoided cases of mortality and morbidity in Shanghai, assuming achievement of China's Class II air quality standards. In Shanghai, the estimated avoided all cause mortality due to PM10 ranged from 13 to 55 cases per day and from 300 to 800 cases per year. The estimated avoided impact on hospital admissions due to PM10 ranged from 230 cases to 580 cases per day and from 5400 to 7900 per year. The estimated avoided impact on all cause mortality due to PM2.5 ranged from 6 to 26 cases per day and from 39 to 1400 per year. The estimated impact on all cause mortality of a year exposure to an annual or monthly mean PM2.5 concentration ranged from 180 to 3500 per year. In Shanghai, the avoided cases of all cause mortality had an estimated monetary value ranging from 170 million yuan (1 US dollar=4.2 yuan Purchasing Power Parity) to 1200 million yuan. Avoided hospital admissions had an estimated value from 20 to 43 million yuan. Avoided emergency department visits had an estimated value from 5.6 million to 15 million yuan. Avoided outpatient visits had an estimated value from 21 million to 31 million yuan. In this analysis, available data were adequate to estimate avoided health impacts and assign monetary value. Sufficient supporting documentation was available to construct and format data sets for use in the United States Environmental Protection Agency's health and environmental assessment model, known as the Environmental Benefits Mapping and Analysis Program - Community Edition ("BenMAP-CE"). Published by Elsevier B.V.

  10. Design and manufacturing status of trim coils for the Wendelstein 7-X stellarator experiment

    Energy Technology Data Exchange (ETDEWEB)

    Riße, K., E-mail: konrad.risse@ipp.mpg.de [Max-Planck-Institut für Plasmaphysik, Greifswald (Germany); Rummel, Th.; Freundt, S.; Dudek, A.; Renard, S.; Bykov, V.; Köppen, M. [Max-Planck-Institut für Plasmaphysik, Greifswald (Germany); Langish, S.; Neilson, G.H.; Brown, Th.; Chrzanowski, J.; Mardenfeld, M.; Malinowski, F.; Khodak, A.; Zhao, X. [Princeton Plasma Physics Laboratory, Princeton, NJ (United States); Eksaa, G. [Everson Tesla Inc., Nazareth, PA (United States)

    2013-10-15

    Highlights: ► The trim coil system will fine tune the main magnetic field during plasma operation by reducing the magnetic field errors. ► The coil design and operational parameters are fixed, the manufacturing is running. ► The coils are equipped with temperature sensors and a voltage tap system to monitor the coil temperature. ► The max. operational deflection is in the order of 4.5 mm; the max. shearing stress across bond planes is of order 16 MPa. ► Special clamps equipped with elastomeric pads allow fixing the coils on the outer cryostat wall. -- Abstract: The stellarator fusion experiment Wendelstein 7-X (W7-X) is currently under construction at the Max-Planck-Institut für Plasmaphysik in Greifswald, Germany. The main magnetic field will be provided by a superconducting magnet system which generates a fivefold toroidal periodic magnetic field. However, unavoidable tolerances can result in small deviations of the magnetic field which disturb the toroidal periodicity. In order to have a tool to influence these field errors five additional normal conducting trim coils were designed to allow fine tuning of the main magnetic field during plasma operation. In the frame of an international cooperation the trim coils will be contributed by the US partners. Princeton Plasma Physics Laboratory has accomplished several tasks to develop the final design ready for manufacturing e.g. detailed manufacturing design for the winding and for the coil connection area. The design work was accompanied by a detailed analysis of resulting forces and moments to prove the design. The manufacturing of the coils is running at Everson Tesla Inc; the first two coils were received at IPP.

  11. The Salmonella Effector Protein SopA Modulates Innate Immune Responses by Targeting TRIM E3 Ligase Family Members.

    Directory of Open Access Journals (Sweden)

    Jana Kamanova

    2016-04-01

    Full Text Available Salmonella Typhimurium stimulates inflammatory responses in the intestinal epithelium, which are essential for its ability to replicate within the intestinal tract. Stimulation of these responses is strictly dependent on the activity of a type III secretion system encoded within its pathogenicity island 1, which through the delivery of effector proteins, triggers signaling pathways leading to inflammation. One of these effectors is SopA, a HECT-type E3 ligase, which is required for the efficient stimulation of inflammation in an animal model of Salmonella Typhimurium infection. We show here that SopA contributes to the stimulation of innate immune responses by targeting two host E3 ubiquitin ligases, TRIM56 and TRIM65. We also found that TRIM65 interacts with the innate immune receptor MDA5 enhancing its ability to stimulate interferon-β signaling. Therefore, by targeting TRIM56 and TRIM65, SopA can stimulate signaling through two innate immune receptors, RIG-I and MDA5. These findings describe a Salmonella mechanism to modulate inflammatory responses by directly targeting innate immune signaling mechanisms.

  12. PENGARUH KARAKTERISTIK PEKERJAAN DAN IKLIM KOMUNIKASI TERHADAP KEPUASAN KERJA KARYAWAN OPERATOR BAGIAN TRIMMING I PT KRAMA YUDHA RATU MOTOR

    Directory of Open Access Journals (Sweden)

    Agung AWS Waspodo

    2013-09-01

    Full Text Available The purpose of the research are: 1 To know the description of job characteristics, communication climate, and job satisfaction employees at trimming 1 PT Krama Yudha Ratu Motor. 2 To know about the influence of job characteristics toward job satisfaction trimming 1 employee’s at PT Krama Yudha Ratu Motor. 3 To know about the influence of communication climate toward job satisfaction trimming 1 employee’s at PT Krama Yudha Ratu Motor. 4 To know about the influence of job characteristics and communication climate toward job satisfaction trimming 1 employee’s at PT Krama Yudha Ratu Motor. The analysis implemented in this research are descriptive and explanatory analysis. This research is taken 71 trimming 1 employee’s at PT Krama Yudha Ratu Motor. While data collection by using questionnaire and cultivated processed using SPSS 16. The result showed that: 1 Job characteristics has a significant influence on job satisfaction. 2 communication climate has a significant influence on job satisfaction. 3 job characteristics and communication climate has a significant influence on job satisfaction.

  13. Frequent silencing of the candidate tumor suppressor TRIM58 by promoter methylation in early-stage lung adenocarcinoma.

    Science.gov (United States)

    Kajiura, Koichiro; Masuda, Kiyoshi; Naruto, Takuya; Kohmoto, Tomohiro; Watabnabe, Miki; Tsuboi, Mitsuhiro; Takizawa, Hiromitsu; Kondo, Kazuya; Tangoku, Akira; Imoto, Issei

    2017-01-10

    In this study, we aimed to identify novel drivers that would be epigenetically altered through aberrant methylation in early-stage lung adenocarcinoma (LADC), regardless of the presence or absence of tobacco smoking-induced epigenetic field defects. Through genome-wide screening for aberrantly methylated CpG islands (CGIs) in 12 clinically uniform, stage-I LADC cases affecting six non-smokers and six smokers, we identified candidate tumor-suppressor genes (TSGs) inactivated by hypermethylation. Through systematic expression analyses of those candidates in panels of additional tumor samples and cell lines treated or not treated with 5-aza-deoxycitidine followed by validation analyses of cancer-specific silencing by CGI hypermethylation using a public database, we identified TRIM58 as the most prominent candidate for TSG. TRIM58 was robustly silenced by hypermethylation even in early-stage primary LADC, and the restoration of TRIM58 expression in LADC cell lines inhibited cell growth in vitro and in vivo in anchorage-dependent and -independent manners. Our findings suggest that aberrant inactivation of TRIM58 consequent to CGI hypermethylation might stimulate the early carcinogenesis of LADC regardless of smoking status; furthermore, TRIM58 methylation might be a possible early diagnostic and epigenetic therapeutic target in LADC.

  14. Two impulse trajectory optimization for the RAE-B orbit trim problem

    Science.gov (United States)

    Payne, M. H.; Pines, S.; Horsewood, J. L.

    1972-01-01

    The results are reported of work on an appropriate approach to the solution of the optimum two-impulse transfer problem between orbits of specified inclination. The task included a literature search to identify the current state of the art and a definition of the suggested approach for the specific application of a lunar orbit trim. The applications of the results to the problem are included. The formulation for a computer program developed under this task following a more conventional approach is also included.

  15. Delamination in surface plies of graphite/epoxy caused by the edge trimming process

    Science.gov (United States)

    Colligan, K.; Ramulu, M.

    Delamination in surface plies of graphite/epoxy laminates caused by edge trimming using polycrystalline diamond (PCD) and carbide cutters is investigated. The effect of several machining variables on formation of delaminations in the surface plies of a graphite fiber reinforced composite material is presented. Machining tests were performed to assess the impact of cutter geometry, feedrate, rotation direction, and graphite fiber orientation. Three typical delamination modes were observed and documented. Feedrate was found to have a significant effect on surface ply delamination in graphite/epoxy composite materials.

  16. Printed board dipole trim magnet design for 20 MeV LIA

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chengjun; Zhu, Wenjun; Zhang, Kaizhi; Zhang, Wenwei; Yu, Haijun [China Academy of Engineering Physics., Chengdu (China). Inst. of Fluid Physics

    1997-12-31

    The printed board dipole trim magnet design for a 20 MeV LIA is presented. The prototype dipole magnet with the sin/cos distributed windings has demonstrated more than 650 Gs-cm integrated dipole field and 1% integrated dipole field homogeneity within 5 cm in radius, which is about 40% of the magnet radius. Numerical modeling of two prototype magnet designs using the 3D magnetic field code SCMAG is presented as well as data from magnetic field measurements of the two magnets. The agreement between the calculations and measurements is accurate to 2-3%. (author). 3 figs., 4 refs.

  17. Modeling and Closed Loop Flight Testing of a Fixed Wing Micro Air Vehicle

    Directory of Open Access Journals (Sweden)

    Harikumar Kandath

    2018-03-01

    Full Text Available This paper presents the nonlinear six degrees of freedom dynamic modeling of a fixed wing micro air vehicle. The static derivatives of the micro air vehicle are obtained through the wind tunnel testing. The propeller effects on the lift, drag, pitching moment and side force are quantified through wind tunnel testing. The dynamic derivatives are obtained through empirical relations available in the literature. The trim conditions are computed for a straight and constant altitude flight condition. The linearized longitudinal and lateral state space models are obtained about trim conditions. The variations in short period mode, phugoid mode, Dutch roll mode, roll subsidence mode and spiral mode with respect to different trim operating conditions is presented. A stabilizing static output feedback controller is designed using the obtained model. Successful closed loop flight trials are conducted with the static output feedback controller.

  18. Regional Issue Identification and Assessment Program (RIIA). A methodology for analyzing the short-term air quality impacts of new power plants: issue paper 5

    Energy Technology Data Exchange (ETDEWEB)

    Lipfert, F.W.

    1979-07-01

    A simplified methodology is presented, based on Gaussian plume relationships, which could be used to assess regulatory constraints and vegetation damage for new power plants. Data input requirements include: (a) power plant size (MW), (b) fuel type, sulfur content, and level of control, and (c) nearby terrain elevation difference, with respect to stack base, for critical receptors. Based on sample calculations the 24-hour PSD increment is seen to be the most restrictive, using the ASME dispersion coefficients. An 800-MW plant (which is close to the optimum size from cost and reliability considerations according to a recent analysis), could be forced to reduce emissions below the levels assumed in this paper if adverse conditions were encountered. For example, terrain features higher than about 300 m at the critical distance from the plant could be restrictive, as could sufficiently persistent winds that would confine 24-hour plume spreading to <10/sup 0/.

  19. Validation and application of the methodology for analysis of radon concentration in the air through the technique of solid state nuclear track detectors (SSNTD)

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Caroline de [Pontificia Universidade Catolica de Minas Gerais (PUC-Pocos), Pocos de Caldas, MG (Brazil); Comissao Nacional de Energia Nuclear (LAPOC/CNEN), Pocos de Caldas, MG (Brazil). Lab. de Pocos de Caldas; Silva, Nivaldo Carlos da, E-mail: ncsilva@cnen.gov.b [Comissao Nacional de Energia Nuclear (LAPOC/CNEN), Pocos de Caldas, MG (Brazil). Lab. de Pocos de Caldas

    2011-07-01

    Radon is a radioactive noble gas that occurs naturally in soil and could enter into residential. The decay products of radon are radioactive metals which, when inhaled, can be retained in the respiratory system, leading to an internal dose of radiation. The monitoring of radon levels in residences and workplaces is extremely important, since high concentrations of this gas can cause serious public health problems. This study analyzed the concentration of radon in the air in 94 work environments at the Laboratory of Pocos de Caldas - LAPOC/CNEN, including laboratories, administrative rooms, workshop, warehouse and guardhouse. The method employed in the monitoring was the technique of solid state nuclear track detectors, known as SSNTD. For calibration and validation of this method, controlled experiments were conducted in laboratory with specific instrumentation. The monitoring results indicated that most environments present radon concentrations above 100 Bq m{sup -3}, which is the reference level recommended by the World Health Organization. (author)

  20. Validation and application of the methodology for analysis of radon concentration in the air through the technique of solid state nuclear track detectors (SSNTD)

    International Nuclear Information System (INIS)

    Carvalho, Caroline de; Comissao Nacional de Energia Nuclear; Silva, Nivaldo Carlos da

    2011-01-01

    Radon is a radioactive noble gas that occurs naturally in soil and could enter into residential. The decay products of radon are radioactive metals which, when inhaled, can be retained in the respiratory system, leading to an internal dose of radiation. The monitoring of radon levels in residences and workplaces is extremely important, since high concentrations of this gas can cause serious public health problems. This study analyzed the concentration of radon in the air in 94 work environments at the Laboratory of Pocos de Caldas - LAPOC/CNEN, including laboratories, administrative rooms, workshop, warehouse and guardhouse. The method employed in the monitoring was the technique of solid state nuclear track detectors, known as SSNTD. For calibration and validation of this method, controlled experiments were conducted in laboratory with specific instrumentation. The monitoring results indicated that most environments present radon concentrations above 100 Bq m -3 , which is the reference level recommended by the World Health Organization. (author)

  1. Technical support document: Energy efficiency standards for consumer products: Room air conditioners, water heaters, direct heating equipment, mobile home furnaces, kitchen ranges and ovens, pool heaters, fluorescent lamp ballasts and television sets. Volume 1, Methodology

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-01

    The Energy Policy and Conservation Act (P.L. 94-163), as amended, establishes energy conservation standards for 12 of the 13 types of consumer products specifically covered by the Act. The legislation requires the Department of Energy (DOE) to consider new or amended standards for these and other types of products at specified times. DOE is currently considering amending standards for seven types of products: water heaters, direct heating equipment, mobile home furnaces, pool heaters, room air conditioners, kitchen ranges and ovens (including microwave ovens), and fluorescent light ballasts and is considering establishing standards for television sets. This Technical Support Document presents the methodology, data, and results from the analysis of the energy and economic impacts of the proposed standards. This volume presents a general description of the analytic approach, including the structure of the major models.

  2. Study of Sylvilagus rabbit TRIM5α species-specific domain: how ancient endoviruses could have shaped the antiviral repertoire in Lagomorpha

    Directory of Open Access Journals (Sweden)

    Areal Helena

    2011-10-01

    Full Text Available Abstract Background Since the first report of the antiretroviral restriction factor TRIM5α in primates, several orthologs in other mammals have been described. Recent studies suggest that leporid retroviruses like RELIK, the first reported endogenous lentivirus ever, may have imposed positive selection in TRIM5α orthologs of the European rabbit and European brown hare. Considering that RELIK must already have been present in a common ancestor of the leporid genera Lepus, Sylvilagus and Oryctolagus, we extended the study of evolutionary patterns of TRIM5α to other members of the Leporidae family, particularly to the genus Sylvilagus. Therefore, we obtained the TRIM5α nucleotide sequences of additional subspecies and species of the three leporid genera. We also compared lagomorph TRIM5α deduced protein sequences and established TRIM5α gene and TRIM5α protein phylogenies. Results The deduced protein sequence of Iberian hare TRIM5α was 89% identical to European rabbit TRIM5α, although high divergence was observed at the PRYSPRY v1 region between rabbit and the identified alleles from this hare species (allele 1: 50% divergence; allele 2: 53% divergence. A high identity was expected between the Sylvilagus and Oryctolagus TRIM5α proteins and, in fact, the Sylvilagus TRIM5α was 91% identical to the Oryctolagus protein. Nevertheless, the PRYSPRY v1 region was only 50% similar between these genera. Selection analysis of Lagomorpha TRIM5α proteins identified 25 positively-selected codons, 11 of which are located in the PRYSPRY v1 region, responsible for species specific differences in viral capsid recognition. Conclusions By extending Lagomorpha TRIM5α studies to an additional genus known to bear RELIK, we verified that the divergent species-specific pattern observed between the Oryctolagus and Lepus PRYSPRY-domains is also present in Sylvilagus TRIM5α. This work is one of the first known studies that compare the evolution of the

  3. Method and apparatus for balancing the magnetic field detecting loops of a cryogenic gradiometer using trimming coils and superconducting disks

    International Nuclear Information System (INIS)

    Lutes, C.L.

    1982-01-01

    An apparatus for and a method of measuring the difference in intensity between two coplanar magnetic field vector components at two different points in space. The device is comprised of two interconnected, relatively large, loop patterns of opposite, flux cancelling, winding sense. One or both loops include a trimming element that is itself formed of two interconnected, relatively small, loop patterns of opposite, flux cancelling, winding sense. The device is analyzed for imbalance between the two large loops and is then balanced by placing a balancing superconducting disk of the proper characteristic in or near one of the two small loops of the trimming element. The so-trimmed apparatus forms a gradiometer of substantially improved mensuration

  4. A robust regression based on weighted LSSVM and penalized trimmed squares

    International Nuclear Information System (INIS)

    Liu, Jianyong; Wang, Yong; Fu, Chengqun; Guo, Jie; Yu, Qin

    2016-01-01

    Least squares support vector machine (LS-SVM) for nonlinear regression is sensitive to outliers in the field of machine learning. Weighted LS-SVM (WLS-SVM) overcomes this drawback by adding weight to each training sample. However, as the number of outliers increases, the accuracy of WLS-SVM may decrease. In order to improve the robustness of WLS-SVM, a new robust regression method based on WLS-SVM and penalized trimmed squares (WLSSVM–PTS) has been proposed. The algorithm comprises three main stages. The initial parameters are obtained by least trimmed squares at first. Then, the significant outliers are identified and eliminated by the Fast-PTS algorithm. The remaining samples with little outliers are estimated by WLS-SVM at last. The statistical tests of experimental results carried out on numerical datasets and real-world datasets show that the proposed WLSSVM–PTS is significantly robust than LS-SVM, WLS-SVM and LSSVM–LTS.

  5. Aperture correction with an asymmetrically trimmed gaussian weight in SPECT with a fan-beam collimator

    International Nuclear Information System (INIS)

    Kamiya, Ryo; Ogawa, Koichi

    2013-01-01

    The aim of the study is to improve the spatial resolution of single photon emission computed tomography (SPECT) images acquired with a fan-beam collimator. The aperture angle of a hole in the fan-beam collimator depends on the position of the collimator. To correct the aperture effect in an iterative image reconstruction, an asymmetrically trimmed Gaussian weight was used for a model. To confirm the validity of our method, point source phantoms and brain phantom were used in the simulation, and we applied the method to the clinical data. The results of the simulation showed that the spatial resolution of point sources improved from about 6 to 2 pixels full width at half maximum, and the corrected point sources were isotropic. The results of the simulation with the brain phantom showed that our proposed method could improve the spatial resolution of the phantom, and our method was effective for different fan-beam collimators with different focal lengths. The results of clinical data showed that the quality of the reconstructed image was improved with our proposed method. Our proposed aperture correction method with the asymmetrically trimmed Gaussian weighting function was effective in improving the spatial resolution of SPECT images acquired with the fan-beam collimator. (author)

  6. Validation of a methodology to determine Benzene, Toluene, Ethylbenzene, and Xylenes concentration present in the air and adsorbed in activated charcoal passive samplers by GC/ FID chromatography

    Directory of Open Access Journals (Sweden)

    Mary Luz Gallego-Díez

    2016-01-01

    Full Text Available En este trabajo se presenta la validación del procedimiento analítico que permite determinar las concentraciones de Benceno (B, Tolueno (T, Etilbenceno (E y Xilenos (X, compuestos conocidos como BTEX, presentes en el aire y adsorbidos sobre carbón activado, usando el método de adición de estándar interno (Fluorobenceno para la cuantificación. En el proceso se empleó carbón activado de referencia para la validación y carbón granular (CGC a base de coco para la construcción de los captadores pasivos, empleados en la toma de muestras en exteriores o aire ambiente. El material CGC fue seleccionado a partir de su capacidad de recuperación de BTEX, con un promedio 89,1% para todos los analitos. En la investigación se evaluó la presencia de BTEX en muestras de aire, tomadas en una vía de seis carriles y caracterizada, además, por ser de alto flujo vehicular en la ciudad de Medellín (Antioquia, Colombia. Los captadores empleados, fueron ubicados en pares por punto (en siete franjas transversales de la vía: andenes oriental, central y occidental, y a alturas que oscilaron entre los 2,50 y 3,00 metros a nivel de piso, dentro de una carcasa especial para su protección. El número de estaciones totales fue de veintiuno (21 en un trayecto de 3 km, para un total de 21 muestras recolectadas con tiempos de exposición de 28 días. El procedimiento de desorción de los analitos se realizó con disulfuro de carbono como solvente de extracción y en el análisis cromatográfico de gases se realizó (por triplicado empleando un detector de ionización de llama (FID. Se usó, además, una columna cromatográfica HP- INNOWAX. El tiempo de corrido empleado fue de 18,5 minutos, usando Helio ultra puro, 99,99% de pureza como gas de arrastre y la cuantificación se llevó a cabo en el extracto líquido en términos de concentración (µg/mL. En la investigación se pudo validar la metodología, obteniendo porcentajes de recuperación que oscilaron

  7. System and method for air temperature control in an oxygen transport membrane based reactor

    Science.gov (United States)

    Kelly, Sean M

    2016-09-27

    A system and method for air temperature control in an oxygen transport membrane based reactor is provided. The system and method involves introducing a specific quantity of cooling air or trim air in between stages in a multistage oxygen transport membrane based reactor or furnace to maintain generally consistent surface temperatures of the oxygen transport membrane elements and associated reactors. The associated reactors may include reforming reactors, boilers or process gas heaters.

  8. On methodology

    DEFF Research Database (Denmark)

    Cheesman, Robin; Faraone, Roque

    2002-01-01

    This is an English version of the methodology chapter in the authors' book "El caso Berríos: Estudio sobre información errónea, desinformación y manipulación de la opinión pública".......This is an English version of the methodology chapter in the authors' book "El caso Berríos: Estudio sobre información errónea, desinformación y manipulación de la opinión pública"....

  9. Osteitis of the apex of the third phalanx following foot trimming in a dairy cow : case report

    Directory of Open Access Journals (Sweden)

    P.N. Thompson

    1998-07-01

    Full Text Available An adult Ayrshire cow was presented with bilateral hind-limb lameness 5 weeks after routine claw trimming. Examination under intravenous regional anaesthesia revealed ulceration of the sole at the toe of both the right lateral and left medial claws of the hind limbs. Radiographic examination showed osteolysis and pathological fractures of the 3rd phalanx of both affected claws. Wooden blocks were fixed to the 2 healthy claws and the bone fragments were removed using a different technique for each claw. Full recovery followed within 11 weeks. The aetiological factors and treatment options for this condition, which was considered to be caused primarily by incorrect claw trimming, are discussed.

  10. Reduced expression of TRIM21/Ro52 predicts poor prognosis in diffuse large B-cell lymphoma patients with and without rheumatic disease

    DEFF Research Database (Denmark)

    Brauner, S; Zhou, W; Backlin, C

    2015-01-01

    OBJECTIVE: TRIM21 (also known as Ro52) is an autoantigen in rheumatic disease and is predominantly expressed in leucocytes. Overexpression is associated with decreased proliferation, and the TRIM21 gene maps to a tumour suppressor locus. We therefore investigated the expression of TRIM21...... in patients with diffuse large B-cell lymphoma (DLBCL) and its potential usefulness as a prognostic biomarker. MATERIALS AND METHODS: TRIM21 expression levels were assessed by immunohistochemistry in lymphoma biopsies from three cohorts of patients with DLBCL: 42 patients with rheumatic disease treated...... with a cyclophosphamide, vincristine, doxorubicin and prednisone (CHOP)-like regimen, 76 CHOP-treated and 196 rituximab-CHOP-treated nonrheumatic patients. Expression was correlated with clinical and biomedical parameters. TRIM21 expression was assessed in relation to lymphocyte proliferation by quantitative PCR...

  11. Body-induced vortical flows: a common mechanism for self-corrective trimming control in boxfishes.

    Science.gov (United States)

    Bartol, Ian K; Gharib, Morteza; Webb, Paul W; Weihs, Daniel; Gordon, Malcolm S

    2005-01-01

    Boxfishes (Teleostei: Ostraciidae) are marine fishes having rigid carapaces that vary significantly among taxa in their shapes and structural ornamentation. We showed previously that the keels of the carapace of one species of tropical boxfish, the smooth trunkfish, produce leading edge vortices (LEVs) capable of generating self-correcting trimming forces during swimming. In this paper we show that other tropical boxfishes with different carapace shapes have similar capabilities. We conducted a quantitative study of flows around the carapaces of three morphologically distinct boxfishes (spotted boxfish, scrawled cowfish and buffalo trunkfish) using stereolithographic models and three separate but interrelated analytical approaches: digital particle image velocimetry (DPIV), pressure distribution measurements, and force balance measurements. The ventral keels of all three forms produced LEVs that grew in circulation along the bodies, resembling the LEVs produced around delta-winged aircraft. These spiral vortices formed above the keels and increased in circulation as pitch angle became more positive, and formed below the keels and increased in circulation as pitch angle became more negative. Vortices also formed along the eye ridges of all boxfishes. In the spotted boxfish, which is largely trapezoidal in cross section, consistent dorsal vortex growth posterior to the eye ridge was also present. When all three boxfishes were positioned at various yaw angles, regions of strongest concentrated vorticity formed in far-field locations of the carapace compared with near-field areas, and vortex circulation was greatest posterior to the center of mass. In general, regions of localized low pressure correlated well with regions of attached, concentrated vorticity, especially around the ventral keels. Although other features of the carapace also affect flow patterns and pressure distributions in different ways, the integrated effects of the flows were consistent for all forms

  12. Trauma Risk Management (TRiM): Promoting Help Seeking for Mental Health Problems Among Combat-Exposed U.K. Military Personnel.

    Science.gov (United States)

    Jones, Norman; Burdett, Howard; Green, Kevin; Greenberg, Neil

    2017-01-01

    Trauma Risk Management (TRiM) is a peer-led, occupational mental health support process that aims to identify and assist U.K. military personnel with persistent mental ill health related to potentially traumatic events (PTEs). This study compared help seeking, mental disorder symptoms, and alcohol use between TRiM recipients and personnel experiencing similar combat events who did not receive TRiM; an unexposed group provided context. Records of TRiM activity during a U.K. military deployment in Afghanistan were linked to contemporaneous survey data assessing mental health and combat experiences. The resulting deployment data set was amalgamated with mental health, alcohol use, and help-seeking data collected within 12 weeks of homecoming and again one to two years later. Mental health and help-seeking outcomes were compared between a nonexposed, non-TRiM sample (n = 161), an exposed, non-TRiM sample (n = 149), and an exposed, TRiM-recipient sample (n = 328) using logistic regression analyses. At follow-up, TRiM recipients were significantly more likely to seek help from mental health services than exposed, non-TRiM personnel. At baseline, TRiM recipients had significantly greater adjusted odds of reporting possible posttraumatic stress disorder (PTSD) symptoms than exposed non-TRiM personnel; the difference was not significant at follow-up. TRiM recipients were significantly more likely to report persistent mental disorder and alcohol misuse caseness over the follow-up period. TRiM recipients were significantly more likely to seek help from mental health services than a similar PTE-exposed group that did not receive TRiM; however, TRiM recipients experienced more persistent mental ill-health symptoms and hazardous alcohol use over the period of follow-up despite seeking help.

  13. Methodological guidelines

    International Nuclear Information System (INIS)

    Halsnaes, K.; Callaway, J.M.; Meyer, H.J.

    1999-01-01

    The guideline document establishes a general overview of the main components of climate change mitigation assessment. This includes an outline of key economic concepts, scenario structure, common assumptions, modelling tools and country study assumptions. The guidelines are supported by Handbook Reports that contain more detailed specifications of calculation standards, input assumptions and available tools. The major objectives of the project have been provided a methodology, an implementing framework and a reporting system which countries can follow in meeting their future reporting obligations under the FCCC and for GEF enabling activities. The project builds upon the methodology development and application in the UNEP National Abatement Coasting Studies (UNEP, 1994a). The various elements provide countries with a road map for conducting climate change mitigation studies and submitting national reports as required by the FCCC. (au) 121 refs

  14. Methodological guidelines

    Energy Technology Data Exchange (ETDEWEB)

    Halsnaes, K.; Callaway, J.M.; Meyer, H.J.

    1999-04-01

    The guideline document establishes a general overview of the main components of climate change mitigation assessment. This includes an outline of key economic concepts, scenario structure, common assumptions, modelling tools and country study assumptions. The guidelines are supported by Handbook Reports that contain more detailed specifications of calculation standards, input assumptions and available tools. The major objectives of the project have been provided a methodology, an implementing framework and a reporting system which countries can follow in meeting their future reporting obligations under the FCCC and for GEF enabling activities. The project builds upon the methodology development and application in the UNEP National Abatement Coasting Studies (UNEP, 1994a). The various elements provide countries with a road map for conducting climate change mitigation studies and submitting national reports as required by the FCCC. (au) 121 refs.

  15. The association of hoof lesions at claw trimming with test-day milk yield in Danish Holsteins

    DEFF Research Database (Denmark)

    Ettema, Jehan Frans; Capion, Nynne; Hill, Ashley E.

    2007-01-01

    on the stage of lactation in which the lesions were diagnosed; during the first 100 days in milk, between days 101 and 200 and between days 201 and 305. Associations between the presence of hoof lesions at trimming and milk production were analyzed by linear mixed modeling at the cow level, clustered within...

  16. Precision-Trimming 2D Inverse-Opal Lattice on Elastomer to Ordered Nanostructures with Variable Size and Morphology.

    Science.gov (United States)

    Zhan, Haoran; Chen, Yanqiu; Liu, Yu; Lau, Woonming; Bao, Chao; Li, Minggan; Lu, Yunlong; Mei, Jun; Hui, David

    2017-05-23

    A low-cost and scalable method is developed for producing large-area elastomer surfaces having ordered nanostructures with a variety of lattice features controllable to nanometer precision. The method adopts the known technique of molding a PDMS precursor film with a close-packed monolayer of monodisperse submicron polystyrene beads on water to form an inverse-opal dimple lattice with the dimple size controlled by the bead selection and the dimple depth by the molding condition. The subsequent novel precision engineering of the inverse-opal lattice comprises trimming the PDMS precursor by a combination of polymer curing temperature/time and polymer dissolution parameters. The resultant ordered surface nanostructures, fabricated with an increasing degree of trimming, include (a) submicron hemispherical dimples with nanothin interdimple rims and walls; (b) nanocones with variable degrees of tip-sharpness by trimming off the top part of the nanothin interdimple walls; and (c) soup-plate-like submicron shallow dimples with interdimple rims and walls by anisotropically trimming off the nanocones and forming close-packed shallow dimples. As exemplars of industrial relevance of these lattice features, tunable Young's modulus and wettability are demonstrated.

  17. Static Aeroelastic and Longitudinal Trim Model of Flexible Wing Aircraft Using Finite-Element Vortex-Lattice Coupled Solution

    Science.gov (United States)

    Ting, Eric; Nguyen, Nhan; Trinh, Khanh

    2014-01-01

    This paper presents a static aeroelastic model and longitudinal trim model for the analysis of a flexible wing transport aircraft. The static aeroelastic model is built using a structural model based on finite-element modeling and coupled to an aerodynamic model that uses vortex-lattice solution. An automatic geometry generation tool is used to close the loop between the structural and aerodynamic models. The aeroelastic model is extended for the development of a three degree-of-freedom longitudinal trim model for an aircraft with flexible wings. The resulting flexible aircraft longitudinal trim model is used to simultaneously compute the static aeroelastic shape for the aircraft model and the longitudinal state inputs to maintain an aircraft trim state. The framework is applied to an aircraft model based on the NASA Generic Transport Model (GTM) with wing structures allowed to flexibly deformed referred to as the Elastically Shaped Aircraft Concept (ESAC). The ESAC wing mass and stiffness properties are based on a baseline "stiff" values representative of current generation transport aircraft.

  18. Distribution and detection of Shiga toxin-producing Escherichia coli (STEC) during an industrial grinding process of beef trim

    Science.gov (United States)

    During the grinding and packaging processes, it is important to understand how Shiga toxin-producing Escherichia coli (STEC) would be distributed and how well it could be detected in beef trim. This study is important because it shows what would happen if contaminated meat is allowed into a commerc...

  19. Trim24 (Tif1 alpha): an essential 'brake' for retinoic acid-induced transcription to prevent liver cancer.

    Science.gov (United States)

    Khetchoumian, Konstantin; Teletin, Marius; Tisserand, Johan; Herquel, Benjamin; Ouararhni, Khalid; Losson, Régine

    2008-12-01

    Retinoic acid (RA), the active derivative of vitamin A, is an important signaling molecule that controls various developmental processes and influence the proliferation and differentiation of a variety of cell types. RA exerts its biological functions primarily through binding to and activating nuclear RA receptors (RARs, which include the RAR alpha, beta and gamma isotypes RARA, RARB and RARC). Aberrant expression or impaired function of these nuclear receptors has been linked to diverse types of cancer. RARs are RA-dependent transcription factors that regulate gene expression through the recruitment of different co-regulators (co-activators and co-repressors). TRIM24 (formerly known as TIF1 alpha) was among the first co-regulators identified as interacting with RARs in a ligand-dependent fashion, and it was recently shown to function in mice as a potent liver-specific tumor suppressor by attenuating Rara-mediated transcription. The fact that Trim24(-/-), but not Trim24(-/-)Rara(+/-), mutant mice are highly predisposed to the development of hepatocellular carcinoma (HCC) has significant implications in cancer research. This result, along with the observation that in response to pharmacological inhibition of the RA signaling, hepatocytes lacking Trim24 loose their ability to proliferate, strongly implicates Rara as a proto-oncogene in hepatocytes and demonstrates that overactivated RA signaling is deleterious to liver homeostasis.

  20. Heteroscedastic Tests Statistics for One-Way Analysis of Variance: The Trimmed Means and Hall's Transformation Conjunction

    Science.gov (United States)

    Luh, Wei-Ming; Guo, Jiin-Huarng

    2005-01-01

    To deal with nonnormal and heterogeneous data for the one-way fixed effect analysis of variance model, the authors adopted a trimmed means method in conjunction with Hall's invertible transformation into a heteroscedastic test statistic (Alexander-Govern test or Welch test). The results of simulation experiments showed that the proposed technique…

  1. Evaluation of the threshold trimming method for micro inertial fluidic switch based on electrowetting technology

    Directory of Open Access Journals (Sweden)

    Tingting Liu

    2014-03-01

    Full Text Available The switch based on electrowetting technology has the advantages of no moving part, low contact resistance, long life and adjustable acceleration threshold. The acceleration threshold of switch can be fine-tuned by adjusting the applied voltage. This paper is focused on the electrowetting properties of switch and the influence of microchannel structural parameters, applied voltage and droplet volume on acceleration threshold. In the presence of process errors of micro inertial fluidic switch and measuring errors of droplet volume, there is a deviation between test acceleration threshold and target acceleration threshold. Considering the process errors and measuring errors, worst-case analysis is used to analyze the influence of parameter tolerance on the acceleration threshold. Under worst-case condition the total acceleration threshold tolerance caused by various errors is 9.95%. The target acceleration threshold can be achieved by fine-tuning the applied voltage. The acceleration threshold trimming method of micro inertial fluidic switch is verified.

  2. Anatomical characterization of hoof growth pattern in six Iranian sheep breeds and its possible implication for trimming recommendations.

    Science.gov (United States)

    Azarpajouh, S; Marchewka, J; Segura Correa, J C; Calderón Díaz, J A

    2018-03-11

    The objective of this study was to compare hoof anatomy, hoof growth pattern, and hoof weight-bearing surface of six different Iranian sheep breeds to identify possible differences in the hoof anatomical features that could help to minimize adverse effects of hoof trimming methods. Front and hind hooves of 2-year-old, previously untrimmed, pastured dairy ewes of six Iranian breeds (Afshari, Moghani, Kurdi, Makoui, Chaleshtori, and Lori-Bakhtiari; n = 180 ewes; 30 ewes per breed) were collected after slaughter. Medial and lateral claws were incised sagittally and anatomical measurements such as toe length, heel height, toe height, sole thickness, sole length, and toe angle were recorded in each claw. Data were analyzed using mixed model equations including breed, claw (lateral or medial), hoof (front or hind) and their interactions as fixed effects, and ewe as random effect. Breed differences were observed for all hoof measurements (P < 0.05). Chaleshtori sheep had higher measurements for most of the traits studied while Afshari and Makoui sheep had lower measurements. All measurements, except for toe length and toe height to solar surface to heel height ratio, were significantly greater in the front hooves than in the hind hooves (P < 0.05). Soles were longer in the medial claws compared to the lateral claws of the front hooves (P < 0.05). Results suggest the observed breed differences could interfere with establishing a standard, uniform hoof trimming method for sheep. For instance, it might be possible that while Afshari and Makoui sheep could require more conservative trimming, Chaleshtori sheep could require to be trimmed more. In consequence, hoof trimming methods might need to be adjusted to specific breed characteristics to avoid possible tissue damage.

  3. Questões metodológicas para a investigação dos efeitos da poluição do ar na saúde Methodological issues of the research on the health effects of air pollution

    Directory of Open Access Journals (Sweden)

    Hermano Albuquerque de Castro

    2003-06-01

    poluição do ar e saúde, levando-se em conta essas questões. Desse modo, pode-se garantir uma melhor qualidade na informação que será utilizada pelos gestores que implementarão essas políticas.Urbanization and the growth of cities have contributed to increase the load of contaminants in the environment. Among contaminants, air pollutants remain a major cause of concern due to their capacity to affect large populations and the fact that several adverse health effects associated with exposure to air pollution have been described in the past few years. This article reviews and discusses some methodological issues involved in the assessment of these health effects. The first issue relates to environmental health indicators (EHI. These indicators can be seen as measures that summarize aspects of the relationship between health and the environment. The EHI methodology proposed by the World Health Organisation for the development of environmental health actions has been applied in the area of air quality. A second aspect relates to the assessment of exposure to air pollution. This is perhaps the most difficult task for studies in this area. Issues concerning different microenvironments (indoor and outdoor are relevant and should be taken in to account in order to minimize the errors associated with the correct assessment of exposure to air pollutants. Lastly, a brief discussion of the main epidemiological study designs used to examine the association between air pollution and health effects is presented. The advantages and disadvantages of the main study types and their main applications are discussed. These are not the only essential issues when studying the deleterious health effects of air pollution on health. However, in order to have sound environmental health policies one needs well designed and conducted epidemiological studies taking in to account these main issues. In this manner, better information will be available to those involved in the decision

  4. MIRD methodology

    International Nuclear Information System (INIS)

    Rojo, Ana M.; Gomez Parada, Ines

    2004-01-01

    The MIRD (Medical Internal Radiation Dose) system was established by the Society of Nuclear Medicine of USA in 1960 to assist the medical community in the estimation of the dose in organs and tissues due to the incorporation of radioactive materials. Since then, 'MIRD Dose Estimate Report' (from the 1 to 12) and 'Pamphlets', of great utility for the dose calculations, were published. The MIRD system was planned essentially for the calculation of doses received by the patients during nuclear medicine diagnostic procedures. The MIRD methodology for the absorbed doses calculations in different tissues is explained

  5. PSA methodology

    Energy Technology Data Exchange (ETDEWEB)

    Magne, L

    1997-12-31

    The purpose of this text is first to ask a certain number of questions on the methods related to PSAs. Notably we will explore the positioning of the French methodological approach - as applied in the EPS 1300{sup 1} and EPS 900{sup 2} PSAs - compared to other approaches (Part One). This reflection leads to more general reflection: what contents, for what PSA? This is why, in Part Two, we will try to offer a framework for definition of the criteria a PSA should satisfy to meet the clearly identified needs. Finally, Part Three will quickly summarize the questions approached in the first two parts, as an introduction to the debate. 15 refs.

  6. PSA methodology

    International Nuclear Information System (INIS)

    Magne, L.

    1996-01-01

    The purpose of this text is first to ask a certain number of questions on the methods related to PSAs. Notably we will explore the positioning of the French methodological approach - as applied in the EPS 1300 1 and EPS 900 2 PSAs - compared to other approaches (Part One). This reflection leads to more general reflection: what contents, for what PSA? This is why, in Part Two, we will try to offer a framework for definition of the criteria a PSA should satisfy to meet the clearly identified needs. Finally, Part Three will quickly summarize the questions approached in the first two parts, as an introduction to the debate. 15 refs

  7. Methodologic frontiers in environmental epidemiology.

    OpenAIRE

    Rothman, K J

    1993-01-01

    Environmental epidemiology comprises the epidemiologic study of those environmental factors that are outside the immediate control of the individual. Exposures of interest to environmental epidemiologists include air pollution, water pollution, occupational exposure to physical and chemical agents, as well as psychosocial elements of environmental concern. The main methodologic problem in environmental epidemiology is exposure assessment, a problem that extends through all of epidemiologic re...

  8. TRIM5 suppresses cross-species transmission of a primate immunodeficiency virus and selects for emergence of resistant variants in the new species.

    Directory of Open Access Journals (Sweden)

    Andrea Kirmaier

    2010-08-01

    Full Text Available Simian immunodeficiency viruses of sooty mangabeys (SIVsm are the source of multiple, successful cross-species transmissions, having given rise to HIV-2 in humans, SIVmac in rhesus macaques, and SIVstm in stump-tailed macaques. Cellular assays and phylogenetic comparisons indirectly support a role for TRIM5alpha, the product of the TRIM5 gene, in suppressing interspecies transmission and emergence of retroviruses in nature. Here, we investigate the in vivo role of TRIM5 directly, focusing on transmission of primate immunodeficiency viruses between outbred primate hosts. Specifically, we retrospectively analyzed experimental cross-species transmission of SIVsm in two cohorts of rhesus macaques and found a significant effect of TRIM5 genotype on viral replication levels. The effect was especially pronounced in a cohort of animals infected with SIVsmE543-3, where TRIM5 genotype correlated with approximately 100-fold to 1,000-fold differences in viral replication levels. Surprisingly, transmission occurred even in individuals bearing restrictive TRIM5 genotypes, resulting in attenuation of replication rather than an outright block to infection. In cell-culture assays, the same TRIM5 alleles associated with viral suppression in vivo blocked infectivity of two SIVsm strains, but not the macaque-adapted strain SIVmac239. Adaptations appeared in the viral capsid in animals with restrictive TRIM5 genotypes, and similar adaptations coincide with emergence of SIVmac in captive macaques in the 1970s. Thus, host TRIM5 can suppress viral replication in vivo, exerting selective pressure during the initial stages of cross-species transmission.

  9. Testing methodologies

    Energy Technology Data Exchange (ETDEWEB)

    Bender, M.A.

    1990-01-01

    Several methodologies are available for screening human populations for exposure to ionizing radiation. Of these, aberration frequency determined in peripheral blood lymphocytes is the best developed. Individual exposures to large doses can easily be quantitated, and population exposures to occupational levels can be detected. However, determination of exposures to the very low doses anticipated from a low-level radioactive waste disposal site is more problematical. Aberrations occur spontaneously, without known cause. Exposure to radiation induces no new or novel types, but only increases their frequency. The limitations of chromosomal aberration dosimetry for detecting low level radiation exposures lie mainly in the statistical signal to noise'' problem, the distribution of aberrations among cells and among individuals, and the possible induction of aberrations by other environmental occupational or medical exposures. However, certain features of the human peripheral lymphocyte-chromosomal aberration system make it useful in screening for certain types of exposures. Future technical developments may make chromosomal aberration dosimetry more useful for low-level radiation exposures. Other methods, measuring gene mutations or even minute changes on the DNA level, while presently less will developed techniques, may eventually become even more practical and sensitive assays for human radiation exposure. 15 refs.

  10. Testing methodologies

    International Nuclear Information System (INIS)

    Bender, M.A.

    1990-01-01

    Several methodologies are available for screening human populations for exposure to ionizing radiation. Of these, aberration frequency determined in peripheral blood lymphocytes is the best developed. Individual exposures to large doses can easily be quantitated, and population exposures to occupational levels can be detected. However, determination of exposures to the very low doses anticipated from a low-level radioactive waste disposal site is more problematical. Aberrations occur spontaneously, without known cause. Exposure to radiation induces no new or novel types, but only increases their frequency. The limitations of chromosomal aberration dosimetry for detecting low level radiation exposures lie mainly in the statistical ''signal to noise'' problem, the distribution of aberrations among cells and among individuals, and the possible induction of aberrations by other environmental occupational or medical exposures. However, certain features of the human peripheral lymphocyte-chromosomal aberration system make it useful in screening for certain types of exposures. Future technical developments may make chromosomal aberration dosimetry more useful for low-level radiation exposures. Other methods, measuring gene mutations or even minute changes on the DNA level, while presently less will developed techniques, may eventually become even more practical and sensitive assays for human radiation exposure. 15 refs

  11. Total aircraft flight-control system - Balanced open- and closed-loop control with dynamic trim maps

    Science.gov (United States)

    Smith, G. A.; Meyer, G.

    1979-01-01

    The availability of the airborne digital computer has made possible a Total Aircraft Flight Control System (TAFCOS) that uses virtually the complete nonlinear propulsive and aerodynamic data for the aircraft to construct dynamic trim maps that represent an inversion of the aircraft model. The trim maps, in series with the aircraft, provide essentially a linear feed-forward path. Basically, open-loop trajectory control is employed with only a small perturbation feedback signal required to compensate for inaccuracy in the aircraft model and for external disturbances. Simulation results for application to an automatic carrier-landing system are presented. Flight-test results for a STOL aircraft operating automatically over a major portion of its flight regime are presented. The concept promises a more rapid and straightforward design from aerodynamic principles, particularly for highly nonlinear configurations, and requires substantially less digital computer capacity than conventional automatic flight-control system designs.

  12. Concerted in vitro trimming of viral HLA-B27-restricted ligands by human ERAP1 and ERAP2 aminopeptidases.

    Science.gov (United States)

    Lorente, Elena; Barriga, Alejandro; Johnstone, Carolina; Mir, Carmen; Jiménez, Mercedes; López, Daniel

    2013-01-01

    In the classical human leukocyte antigen (HLA) class I antigen processing and presentation pathway, the antigenic peptides are generated from viral proteins by multiple proteolytic cleavages of the proteasome (and in some cases other cytosolic proteases) and transported to the endoplasmic reticulum (ER) lumen where they are exposed to aminopeptidase activity. In human cells, two different ER-resident enzymes, ERAP1 and ERAP2, can trim the N-terminally extended residues of peptide precursors. In this study, the possible cooperative effect of generating five naturally processed HLA-B27 ligands by both proteases was analyzed. We identified differences in the products obtained with increased detection of natural HLA-B27 ligands by comparing double versus single enzyme digestions by mass spectrometry analysis. These in vitro data suggest that each enzyme can use the degradation products of the other as a substrate for new N-terminal trimming, indicating concerted aminoproteolytic activity of ERAP 1 and ERAP2.

  13. Characteristics of a continuous denitration by formic acid - electrolytic trimming of residual acid with accompanying the precipitation of metal ions

    International Nuclear Information System (INIS)

    Kim, G. W.; Kim, S. H.; Lim, J. G.; Lee, I. H.

    2003-01-01

    This work has studied the characteristics of destruction of nitric acid and precipitation of several metal ions in a continuous denitration process combining a denitration by formic acid and a residual acid-electrolytic trimming system. The metal ions of Zr, Mo, Fe, and Nd did not affect the electrodes at the step of electrolytic trimming of the residual acid after denitration by formic acid. The Mo ion in electrolytic solution enhanced the generation of nitrite ion during the electrolytic reaction. The mole ratio of formic acid to nitric acid fed into the continuous denitration reactor using formic acid affected much the final acidity, the precipitation yields of metal ions, the precipitate morphology. At the ratio of 1.65, the process had the lowest final acidity of less than 0.1 M, and the precipitation yields of Zr and Mo reached 95% and 83%, respectively as the highest values

  14. Recovering probabilities for nucleotide trimming processes for T cell receptor TRA and TRG V-J junctions analyzed with IMGT tools

    Directory of Open Access Journals (Sweden)

    Lefranc Marie-Paule

    2008-10-01

    Full Text Available Abstract Background Nucleotides are trimmed from the ends of variable (V, diversity (D and joining (J genes during immunoglobulin (IG and T cell receptor (TR rearrangements in B cells and T cells of the immune system. This trimming is followed by addition of nucleotides at random, forming the N regions (N for nucleotides of the V-J and V-D-J junctions. These processes are crucial for creating diversity in the immune response since the number of trimmed nucleotides and the number of added nucleotides vary in each B or T cell. IMGT® sequence analysis tools, IMGT/V-QUEST and IMGT/JunctionAnalysis, are able to provide detailed and accurate analysis of the final observed junction nucleotide sequences (tool "output". However, as trimmed nucleotides can potentially be replaced by identical N region nucleotides during the process, the observed "output" represents a biased estimate of the "true trimming process." Results A probabilistic approach based on an analysis of the standardized tool "output" is proposed to infer the probability distribution of the "true trimmming process" and to provide plausible biological hypotheses explaining this process. We collated a benchmark dataset of TR alpha (TRA and TR gamma (TRG V-J rearranged sequences and junctions analysed with IMGT/V-QUEST and IMGT/JunctionAnalysis, the nucleotide sequence analysis tools from IMGT®, the international ImMunoGeneTics information system®, http://imgt.cines.fr. The standardized description of the tool output is based on the IMGT-ONTOLOGY axioms and concepts. We propose a simple first-order model that attempts to transform the observed "output" probability distribution into an estimate closer to the "true trimming process" probability distribution. We use this estimate to test the hypothesis that Poisson processes are involved in trimming. This hypothesis was not rejected at standard confidence levels for three of the four trimming processes: TRAV, TRAJ and TRGV. Conclusion By

  15. Recovering probabilities for nucleotide trimming processes for T cell receptor TRA and TRG V-J junctions analyzed with IMGT tools.

    Science.gov (United States)

    Bleakley, Kevin; Lefranc, Marie-Paule; Biau, Gérard

    2008-10-02

    Nucleotides are trimmed from the ends of variable (V), diversity (D) and joining (J) genes during immunoglobulin (IG) and T cell receptor (TR) rearrangements in B cells and T cells of the immune system. This trimming is followed by addition of nucleotides at random, forming the N regions (N for nucleotides) of the V-J and V-D-J junctions. These processes are crucial for creating diversity in the immune response since the number of trimmed nucleotides and the number of added nucleotides vary in each B or T cell. IMGT sequence analysis tools, IMGT/V-QUEST and IMGT/JunctionAnalysis, are able to provide detailed and accurate analysis of the final observed junction nucleotide sequences (tool "output"). However, as trimmed nucleotides can potentially be replaced by identical N region nucleotides during the process, the observed "output" represents a biased estimate of the "true trimming process." A probabilistic approach based on an analysis of the standardized tool "output" is proposed to infer the probability distribution of the "true trimmming process" and to provide plausible biological hypotheses explaining this process. We collated a benchmark dataset of TR alpha (TRA) and TR gamma (TRG) V-J rearranged sequences and junctions analysed with IMGT/V-QUEST and IMGT/JunctionAnalysis, the nucleotide sequence analysis tools from IMGT, the international ImMunoGeneTics information system, http://imgt.cines.fr. The standardized description of the tool output is based on the IMGT-ONTOLOGY axioms and concepts. We propose a simple first-order model that attempts to transform the observed "output" probability distribution into an estimate closer to the "true trimming process" probability distribution. We use this estimate to test the hypothesis that Poisson processes are involved in trimming. This hypothesis was not rejected at standard confidence levels for three of the four trimming processes: TRAV, TRAJ and TRGV. By using trimming of rearranged TR genes as a benchmark, we

  16. Computation of the Distribution of the Fiber-Matrix Interface Cracks in the Edge Trimming of CFRP

    Science.gov (United States)

    Wang, Fu-ji; Zhang, Bo-yu; Ma, Jian-wei; Bi, Guang-jian; Hu, Hai-bo

    2018-04-01

    Edge trimming is commonly used to bring the CFRP components to right dimension and shape in aerospace industries. However, various forms of undesirable machining damage occur frequently which will significantly decrease the material performance of CFRP. The damage is difficult to predict and control due to the complicated changing laws, causing unsatisfactory machining quality of CFRP components. Since the most of damage has the same essence: the fiber-matrix interface cracks, this study aims to calculate the distribution of them in edge trimming of CFRP, thereby to obtain the effects of the machining parameters, which could be helpful to guide the optimal selection of the machining parameters in engineering. Through the orthogonal cutting experiments, the quantitative relation between the fiber-matrix interface crack depth and the fiber cutting angle, cutting depth as well as cutting speed is established. According to the analysis on material removal process on any location of the workpiece in edge trimming, the instantaneous cutting parameters are calculated, and the formation process of the fiber-matrix interface crack is revealed. Finally, the computational method for the fiber-matrix interface cracks in edge trimming of CFRP is proposed. Upon the computational results, it is found that the fiber orientations of CFRP workpieces is the most significant factor on the fiber-matrix interface cracks, which can not only change the depth of them from micrometers to millimeters, but control the distribution image of them. Other machining parameters, only influence the fiber-matrix interface cracks depth but have little effect on the distribution image.

  17. Hypermethylation of TRIM59 and KLF14 Influences Cell Death Signaling in Familial Alzheimer’s Disease

    Directory of Open Access Journals (Sweden)

    Michalina Wezyk

    2018-01-01

    Full Text Available Epigenetic mechanisms play an important role in the development and progression of various neurodegenerative diseases. Abnormal methylation of numerous genes responsible for regulation of transcription, DNA replication, and apoptosis has been linked to Alzheimer’s disease (AD pathology. We have recently performed whole transcriptome profiling of familial early-onset Alzheimer’s disease (fEOAD patient-derived fibroblasts. On this basis, we demonstrated a strong dysregulation of cell cycle checkpoints and DNA damage response (DDR in both fibroblasts and reprogrammed neurons. Here, we show that the aging-correlated hypermethylation of KLF14 and TRIM59 genes associates with abnormalities in DNA repair and cell cycle control in fEOAD. Based on the resulting transcriptome networks, we found that the hypermethylation of KLF14 might be associated with epigenetic regulation of the chromatin organization and mRNA processing followed by hypermethylation of TRIM59 likely associated with the G2/M cell cycle phase and p53 role in DNA repair with BRCA1 protein as the key player. We propose that the hypermethylation of KLF14 could constitute a superior epigenetic mechanism for TRIM59 hypermethylation. The methylation status of both genes affects genome stability and might contribute to proapoptotic signaling in AD. Since this study combines data obtained from various tissues from AD patients, it reinforces the view that the genetic methylation status in the blood may be a valuable predictor of molecular processes occurring in affected tissues. Further research is necessary to define a detailed role of TRIM59 and KLF4 in neurodegeneration of neurons.

  18. SseK3 Is a Salmonella Effector That Binds TRIM32 and Modulates the Host's NF-κB Signalling Activity.

    Directory of Open Access Journals (Sweden)

    Zhe Yang

    Full Text Available Salmonella Typhimurium employs an array of type III secretion system effectors that facilitate intracellular survival and replication during infection. The Salmonella effector SseK3 was originally identified due to amino acid sequence similarity with NleB; an effector secreted by EPEC/EHEC that possesses N-acetylglucoasmine (GlcNAc transferase activity and modifies death domain containing proteins to block extrinsic apoptosis. In this study, immunoprecipitation of SseK3 defined a novel molecular interaction between SseK3 and the host protein, TRIM32, an E3 ubiquitin ligase. The conserved DxD motif within SseK3, which is essential for the GlcNAc transferase activity of NleB, was required for TRIM32 binding and for the capacity of SseK3 to suppress TNF-stimulated activation of NF-κB pathway. However, we did not detect GlcNAc modification of TRIM32 by SseK3, nor did the SseK3-TRIM32 interaction impact on TRIM32 ubiquitination that is associated with its activation. In addition, lack of sseK3 in Salmonella had no effect on production of the NF-κB dependent cytokine, IL-8, in HeLa cells even though TRIM32 knockdown suppressed TNF-induced NF-κB activity. Ectopically expressed SseK3 partially co-localises with TRIM32 at the trans-Golgi network, but SseK3 is not recruited to Salmonella induced vacuoles or Salmonella induced filaments during Salmonella infection. Our study has identified a novel effector-host protein interaction and suggests that SseK3 may influence NF-κB activity. However, the lack of GlcNAc modification of TRIM32 suggests that SseK3 has further, as yet unidentified, host targets.

  19. Improved approach to quantitative cardiac volumetrics using automatic thresholding and manual trimming: a cardiovascular MRI study.

    Science.gov (United States)

    Rayarao, Geetha; Biederman, Robert W W; Williams, Ronald B; Yamrozik, June A; Lombardi, Richard; Doyle, Mark

    2018-01-01

    To establish the clinical validity and accuracy of automatic thresholding and manual trimming (ATMT) by comparing the method with the conventional contouring method for in vivo cardiac volume measurements. CMR was performed on 40 subjects (30 patients and 10 controls) using steady-state free precession cine sequences with slices oriented in the short-axis and acquired contiguously from base to apex. Left ventricular (LV) volumes, end-diastolic volume, end-systolic volume, and stroke volume (SV) were obtained with ATMT and with the conventional contouring method. Additionally, SV was measured independently using CMR phase velocity mapping (PVM) of the aorta for validation. Three methods of calculating SV were compared by applying Bland-Altman analysis. The Bland-Altman standard deviation of variation (SD) and offset bias for LV SV for the three sets of data were: ATMT-PVM (7.65, [Formula: see text]), ATMT-contours (7.85, [Formula: see text]), and contour-PVM (11.01, 4.97), respectively. Equating the observed range to the error contribution of each approach, the error magnitude of ATMT:PVM:contours was in the ratio 1:2.4:2.5. Use of ATMT for measuring ventricular volumes accommodates trabeculae and papillary structures more intuitively than contemporary contouring methods. This results in lower variation when analyzing cardiac structure and function and consequently improved accuracy in assessing chamber volumes.

  20. Dynamics of trimming the content of face representations for categorization in the brain.

    Directory of Open Access Journals (Sweden)

    Nicola J van Rijsbergen

    2009-11-01

    Full Text Available To understand visual cognition, it is imperative to determine when, how and with what information the human brain categorizes the visual input. Visual categorization consistently involves at least an early and a late stage: the occipito-temporal N170 event related potential related to stimulus encoding and the parietal P300 involved in perceptual decisions. Here we sought to understand how the brain globally transforms its representations of face categories from their early encoding to the later decision stage over the 400 ms time window encompassing the N170 and P300 brain events. We applied classification image techniques to the behavioral and electroencephalographic data of three observers who categorized seven facial expressions of emotion and report two main findings: (1 over the 400 ms time course, processing of facial features initially spreads bilaterally across the left and right occipito-temporal regions to dynamically converge onto the centro-parietal region; (2 concurrently, information processing gradually shifts from encoding common face features across all spatial scales (e.g., the eyes to representing only the finer scales of the diagnostic features that are richer in useful information for behavior (e.g., the wide opened eyes in 'fear'; the detailed mouth in 'happy'. Our findings suggest that the brain refines its diagnostic representations of visual categories over the first 400 ms of processing by trimming a thorough encoding of features over the N170, to leave only the detailed information important for perceptual decisions over the P300.

  1. Antimicrobial activity of poultry bone and meat trimmings hydrolyzates in low-sodium turkey food.

    Science.gov (United States)

    Zanello, Pier Paolo; Sforza, Stefano; Dossena, Arnaldo; Lambertini, Francesca; Bottesini, Chiara; Nikolaev, Ilya V; Koroleva, Olga; Ciociola, Tecla; Magliani, Walter; Conti, Stefania; Polonelli, Luciano

    2014-02-01

    This research was aimed at the evaluation of the antimicrobial activity exerted by poultry protein hydrolyzates derived from industrial leftovers added to minced turkey meat, intended for the production of burgers for human consumption. Hydrolyzates were obtained through enzymatic hydrolysis from poultry bone and meat trimmings, as by-products from the poultry industry. Colony forming unit assays, under both laboratory and industrial conditions, were performed to assess microbial growth. Poultry protein hydrolyzates inhibited microbial growth occurring in semi-finished turkey meat during the normal retention period because of their water holding capacity resulting in a decreased water activity. Overall, the findings demonstrated that poultry protein hydrolyzates could decrease mesophilic, psychrophilic, and thermophilic bacterial growth for the entire product shelf-life. Bacterial growth inhibition obtained in minced turkey meat by addition of poultry protein hydrolyzates (1.5%), hygroscopic amino acids mixture (1.5%) or sodium chloride (1%) was similar. It is suggested that the use of hydrolyzates could allow the reduction of salt content in poultry meat based products leading to the production of low-sodium turkey food still maintaining acceptable sensory characteristics.

  2. Shrinkage covariance matrix approach based on robust trimmed mean in gene sets detection

    Science.gov (United States)

    Karjanto, Suryaefiza; Ramli, Norazan Mohamed; Ghani, Nor Azura Md; Aripin, Rasimah; Yusop, Noorezatty Mohd

    2015-02-01

    Microarray involves of placing an orderly arrangement of thousands of gene sequences in a grid on a suitable surface. The technology has made a novelty discovery since its development and obtained an increasing attention among researchers. The widespread of microarray technology is largely due to its ability to perform simultaneous analysis of thousands of genes in a massively parallel manner in one experiment. Hence, it provides valuable knowledge on gene interaction and function. The microarray data set typically consists of tens of thousands of genes (variables) from just dozens of samples due to various constraints. Therefore, the sample covariance matrix in Hotelling's T2 statistic is not positive definite and become singular, thus it cannot be inverted. In this research, the Hotelling's T2 statistic is combined with a shrinkage approach as an alternative estimation to estimate the covariance matrix to detect significant gene sets. The use of shrinkage covariance matrix overcomes the singularity problem by converting an unbiased to an improved biased estimator of covariance matrix. Robust trimmed mean is integrated into the shrinkage matrix to reduce the influence of outliers and consequently increases its efficiency. The performance of the proposed method is measured using several simulation designs. The results are expected to outperform existing techniques in many tested conditions.

  3. Mitigation options : flare and vent mitigation undercuts CCS in trimming CO{sub 2} emissions

    Energy Technology Data Exchange (ETDEWEB)

    Smith, M.

    2010-11-15

    This article reported on a study aimed at reducing flaring and venting associated with conventional heavy oil production. In particular, the study analyzed parameters such as the variability in flare volumes, flare gas composition and statistical distribution of volumes flared. The objective was to determine the most viable economic solution to reducing flare and vent volumes. In particular, the study focused on various scenarios to tie-in currently flared and vented solution gas. Solution gas volume variability was found to be wide ranging, with 90 percent of sites handling less than 32 percent of the volume and 10 percent of the sites handling more than two-thirds of the volume. Composition also varied, and was difficult to measure. One scenario assumed that wells were unconnected and had to be tied in with their own compressors and pipe, while another scenario considered the wells to be individual wells. A first comprehensive analysis of flare and vent mitigation opportunities in Alberta revealed that tying in solution gas at battery sites could create emissions reductions at much lower cost than the province's carbon capture and storage (CCS) plan. The study of mitigation options primarily targeted the conventional heavy oil belt of eastern Alberta near Lloydminster. The most optimistic scenario included a $15 per tonne carbon credit, that up to 55 megatonnes could be trimmed over 10 years at no cost to the industry.1 fig.

  4. Information trimming: Sufficient statistics, mutual information, and predictability from effective channel states

    Science.gov (United States)

    James, Ryan G.; Mahoney, John R.; Crutchfield, James P.

    2017-06-01

    One of the most basic characterizations of the relationship between two random variables, X and Y , is the value of their mutual information. Unfortunately, calculating it analytically and estimating it empirically are often stymied by the extremely large dimension of the variables. One might hope to replace such a high-dimensional variable by a smaller one that preserves its relationship with the other. It is well known that either X (or Y ) can be replaced by its minimal sufficient statistic about Y (or X ) while preserving the mutual information. While intuitively reasonable, it is not obvious or straightforward that both variables can be replaced simultaneously. We demonstrate that this is in fact possible: the information X 's minimal sufficient statistic preserves about Y is exactly the information that Y 's minimal sufficient statistic preserves about X . We call this procedure information trimming. As an important corollary, we consider the case where one variable is a stochastic process' past and the other its future. In this case, the mutual information is the channel transmission rate between the channel's effective states. That is, the past-future mutual information (the excess entropy) is the amount of information about the future that can be predicted using the past. Translating our result about minimal sufficient statistics, this is equivalent to the mutual information between the forward- and reverse-time causal states of computational mechanics. We close by discussing multivariate extensions to this use of minimal sufficient statistics.

  5. Soda-anthraquinone, kraft and organosolv pulping of holm oak trimmings.

    Science.gov (United States)

    Alaejos, J; López, F; Eugenio, M E; Tapias, R

    2006-11-01

    The operating conditions for an organosolv (ethyleneglycol) and two alkaline (soda-anthraquinone and kraft) processes for obtaining cellulose pulp and paper from holm oak (Quercus ilex) wood trimmings were optimized. A range of variation for each process variable (viz. temperature, cooking time and soda or ethyleneglycol concentration) was established and a central composite experimental design involving three independent variables at three different variation levels was applied. The results obtained with the three cooking processes used were compared and those provided by the kraft process were found to be the best. Thus, the tensile index values it provided (5.9-16.3 N m/g) were 23.7% and 41.5% better than those obtained with the soda-AQ and ethyleneglycol processes, respectively. Also, the kraft process provided the best burst index, brightness and kappa number values. Based on the optimum working ranges, the temperature and cooking time were the variables resulting in the most and least marked changes, respectively, in pulp properties.

  6. Arthroscopic medial meniscus trimming or repair under nerve blocks: Which nerves should be blocked?

    Science.gov (United States)

    Taha, AM; Abd-Elmaksoud, AM

    2016-01-01

    Background: This study aimed to determine the role of the sciatic and obturator nerve blocks (in addition to femoral block) in providing painless arthroscopic medial meniscus trimming/repair. Materials and Methods: One hundred and twenty patients with medial meniscus tear, who had been scheduled to knee arthroscopy, were planned to be included in this controlled prospective double-blind study. The patients were randomly allocated into three equal groups; FSO, FS, and FO. The femoral, sciatic, and obturator nerves were blocked in FSO groups. The femoral and sciatic nerves were blocked in FS group, while the femoral and obturator nerves were blocked in FO group. Intraoperative pain and its causative surgical maneuver were recorded. Results: All the patients (n = 7, 100%) in FO group had intraoperative pain. The research was terminated in this group but completed in FS and FSO groups (40 patients each). During valgus positioning of the knee for surgical management of the medial meniscus tear, the patients in FS group experienced pain more frequently than those in FSO group (P = 0.005). Conclusion: Adding a sciatic nerve block to the femoral nerve block is important for painless knee arthroscopy. Further adding of an obturator nerve block may be needed when a valgus knee position is required to manage the medial meniscus tear. PMID:27375382

  7. Deep Sequence Analysis of AgoshRNA Processing Reveals 3' A Addition and Trimming.

    Science.gov (United States)

    Harwig, Alex; Herrera-Carrillo, Elena; Jongejan, Aldo; van Kampen, Antonius Hubertus; Berkhout, Ben

    2015-07-14

    The RNA interference (RNAi) pathway, in which microprocessor and Dicer collaborate to process microRNAs (miRNA), was recently expanded by the description of alternative processing routes. In one of these noncanonical pathways, Dicer action is replaced by the Argonaute2 (Ago2) slicer function. It was recently shown that the stem-length of precursor-miRNA or short hairpin RNA (shRNA) molecules is a major determinant for Dicer versus Ago2 processing. Here we present the results of a deep sequence study on the processing of shRNAs with different stem length and a top G·U wobble base pair (bp). This analysis revealed some unexpected properties of these so-called AgoshRNA molecules that are processed by Ago2 instead of Dicer. First, we confirmed the gradual shift from Dicer to Ago2 processing upon shortening of the hairpin length. Second, hairpins with a stem larger than 19 base pair are inefficiently cleaved by Ago2 and we noticed a shift in the cleavage site. Third, the introduction of a top G·U bp in a regular shRNA can promote Ago2-cleavage, which coincides with a loss of Ago2-loading of the Dicer-cleaved 3' strand. Fourth, the Ago2-processed AgoshRNAs acquire a short 3' tail of 1-3 A-nucleotides (nt) and we present evidence that this product is subsequently trimmed by the poly(A)-specific ribonuclease (PARN).

  8. Optimization of Support Structures for Offshore Wind Turbines Using Genetic Algorithm with Domain-Trimming

    Directory of Open Access Journals (Sweden)

    Mohammad AlHamaydeh

    2017-01-01

    Full Text Available The powerful genetic algorithm optimization technique is augmented with an innovative “domain-trimming” modification. The resulting adaptive, high-performance technique is called Genetic Algorithm with Domain-Trimming (GADT. As a proof of concept, the GADT is applied to a widely used benchmark problem. The 10-dimensional truss optimization benchmark problem has well documented global and local minima. The GADT is shown to outperform several published solutions. Subsequently, the GADT is deployed onto three-dimensional structural design optimization for offshore wind turbine supporting structures. The design problem involves complex least-weight topology as well as member size optimizations. The GADT is applied to two popular design alternatives: tripod and quadropod jackets. The two versions of the optimization problem are nonlinearly constrained where the objective function is the material weight of the supporting truss. The considered design variables are the truss members end node coordinates, as well as the cross-sectional areas of the truss members, whereas the constraints are the maximum stresses in members and the maximum displacements of the nodes. These constraints are managed via dynamically modified, nonstationary penalty functions. The structures are subject to gravity, wind, wave, and earthquake loading conditions. The results show that the GADT method is superior in finding best discovered optimal solutions.

  9. Effect of irradiation of frozen meat/fat trimmings on microbiological and physicochemical quality attributes of dry fermented sausages.

    Science.gov (United States)

    Chouliara, I; Samelis, J; Kakouri, A; Badeka, A; Savvaidis, I N; Riganakos, K; Kontominas, M G

    2006-10-01

    Changes in microbiological and physicochemical quality attributes resulting from the use of irradiation in the production of Greek dry fermented sausage were investigated as a function of fermentation/ripening time. Results showed that irradiating meat/fat trimmings at 2 or 4kGy prior to sausage production eliminated natural contamination with Listeria spp., and reduced pseudomonads, enterococci and pathogenic staphylococci, and enterobacteria, to less than 2 and 1logcfug(-1), respectively. Pseudomonads were very sensitive (>3.4 log reduction) to either radiation dose. Yeasts were the most resistant followed by inherent lactic acid bacteria; their reductions on the trimmings were radiation dose-dependent. Residual effects of irradiation were noted against enterococci, but not against gram-negatives which died off fast during fermentation even in non-irradiated samples. Growth of the starter bacteria, Lactobacillus pentosus and Staphylococcus carnosus, inoculated in the sausage batters post-irradiation was unaffected by the 2 or 4kGy pre-treatment of the trimmings. Irradiation had little or no effect at the end of ripening period (28 days) on pH, moisture content and color (parameters L(∗), a(∗), and b(∗)). Changes in TBA values were small but statistically significant with irradiated samples having higher TBA values than control samples.

  10. Poly(A-Specific Ribonuclease Mediates 3′-End Trimming of Argonaute2-Cleaved Precursor MicroRNAs

    Directory of Open Access Journals (Sweden)

    Mayuko Yoda

    2013-11-01

    Full Text Available MicroRNAs (miRNAs are typically generated as ∼22-nucleotide double-stranded RNAs via the processing of precursor hairpins by the ribonuclease III enzyme Dicer, after which they are loaded into Argonaute (Ago proteins to form an RNA-induced silencing complex (RISC. However, the biogenesis of miR-451, an erythropoietic miRNA conserved in vertebrates, occurs independently of Dicer and instead requires cleavage of the 3′ arm of the pre-miR-451 precursor hairpin by Ago2. The 3′ end of the Ago2-cleaved pre-miR-451 intermediate is then trimmed to the mature length by an unknown nuclease. Here, using a classical chromatographic approach, we identified poly(A-specific ribonuclease (PARN as the enzyme responsible for the 3′–5′ exonucleolytic trimming of Ago2-cleaved pre-miR-451. Surprisingly, our data show that trimming of Ago2-cleaved precursor miRNAs is not essential for target silencing, indicating that RISC is functional with miRNAs longer than the mature length. Our findings define the maturation step in the miRNA biogenesis pathway that depends on Ago2-mediated cleavage.

  11. TRIM30α Is a Negative-Feedback Regulator of the Intracellular DNA and DNA Virus-Triggered Response by Targeting STING.

    Directory of Open Access Journals (Sweden)

    Yanming Wang

    2015-06-01

    Full Text Available Uncontrolled immune responses to intracellular DNA have been shown to induce autoimmune diseases. Homeostasis regulation of immune responses to cytosolic DNA is critical for limiting the risk of autoimmunity and survival of the host. Here, we report that the E3 ubiquitin ligase tripartite motif protein 30α (TRIM30α was induced by herpes simplex virus type 1 (HSV-1 infection in dendritic cells (DCs. Knockdown or genetic ablation of TRIM30α augmented the type I IFNs and interleukin-6 response to intracellular DNA and DNA viruses. Trim30α-deficient mice were more resistant to infection by DNA viruses. Biochemical analyses showed that TRIM30α interacted with the stimulator of interferon genes (STING, which is a critical regulator of the DNA-sensing response. Overexpression of TRIM30α promoted the degradation of STING via K48-linked ubiquitination at Lys275 through a proteasome-dependent pathway. These findings indicate that E3 ligase TRIM30α is an important negative-feedback regulator of innate immune responses to DNA viruses by targeting STING.

  12. The E3 Ubiquitin Ligase TRIM40 Attenuates Antiviral Immune Responses by Targeting MDA5 and RIG-I

    Directory of Open Access Journals (Sweden)

    Chunyuan Zhao

    2017-11-01

    Full Text Available Retinoic acid-inducible gene-I (RIG-I-like receptors (RLRs, including melanoma differentiation-associated gene 5 (MDA5 and RIG-I, are crucial for host recognition of non-self RNAs, especially viral RNA. Thus, the expression and activation of RLRs play fundamental roles in eliminating the invading RNA viruses and maintaining immune homeostasis. However, how RLR expression is tightly regulated remains to be further investigated. In this study, we identified a major histocompatibility complex (MHC-encoded gene, tripartite interaction motif 40 (TRIM40, as a suppressor of RLR signaling by directly targeting MDA5 and RIG-I. TRIM40 binds to MDA5 and RIG-I and promotes their K27- and K48-linked polyubiquitination via its E3 ligase activity, leading to their proteasomal degradation. TRIM40 deficiency enhances RLR-triggered signaling. Consequently, TRIM40 deficiency greatly enhances antiviral immune responses and decreases viral replication in vivo. Thus, we demonstrate that TRIM40 limits RLR-triggered innate activation, suggesting TRIM40 as a potential therapeutic target for the control of viral infection.

  13. Scoring-and-unfolding trimmed tree assembler: concepts, constructs and comparisons.

    Science.gov (United States)

    Narzisi, Giuseppe; Mishra, Bud

    2011-01-15

    Mired by its connection to a well-known -complete combinatorial optimization problem-namely, the Shortest Common Superstring Problem (SCSP)-historically, the whole-genome sequence assembly (WGSA) problem has been assumed to be amenable only to greedy and heuristic methods. By placing efficiency as their first priority, these methods opted to rely only on local searches, and are thus inherently approximate, ambiguous or error prone, especially, for genomes with complex structures. Furthermore, since choice of the best heuristics depended critically on the properties of (e.g. errors in) the input data and the available long range information, these approaches hindered designing an error free WGSA pipeline. We dispense with the idea of limiting the solutions to just the approximated ones, and instead favor an approach that could potentially lead to an exhaustive (exponential-time) search of all possible layouts. Its computational complexity thus must be tamed through a constrained search (Branch-and-Bound) and quick identification and pruning of implausible overlays. For his purpose, such a method necessarily relies on a set of score functions (oracles) that can combine different structural properties (e.g. transitivity, coverage, physical maps, etc.). We give a detailed description of this novel assembly framework, referred to as Scoring-and-Unfolding Trimmed Tree Assembler (SUTTA), and present experimental results on several bacterial genomes using next-generation sequencing technology data. We also report experimental evidence that the assembly quality strongly depends on the choice of the minimum overlap parameter k. SUTTA's binaries are freely available to non-profit institutions for research and educational purposes at http://www.bioinformatics.nyu.edu.

  14. The Reversal Intervention for Metabolic Syndrome (TRIMS study: rationale, design, and baseline data

    Directory of Open Access Journals (Sweden)

    Troughton Jacqui

    2011-05-01

    Full Text Available Abstract Background Recent attention has focused on strategies to combat the forecast epidemic of type-2 diabetes (T2DM and its major vascular sequelae. Metabolic syndrome (MetS comprises a constellation of factors that increase the risk of cardiovascular disease (CVD and T2DM. Our study aims to develop a structured self-management education programme for people with MetS, which includes management of cardiovascular and diabetes risk factors, and to determine its impact. This paper describes the rationale and design of the TRIMS study, including intervention development, and presents baseline data. Methods Subjects recruited from a mixed-ethnic population with MetS were randomised to intervention or control arms. The intervention arm received structured group education based on robust psychological theories and current evidence. The control group received routine care. Follow-up data will be collected at 6 and 12 months. The primary outcome measure will be reversal of metabolic syndrome in the intervention group subjects compared to controls at 12 months follow-up. Results 82 participants (44% male, 22% South Asian were recruited between November 2009 and July 2010. Baseline characteristics were similar for both the intervention (n = 42 and control groups (n = 40. Median age was 63 years (IQR 57 - 67, mean waist size 106 cm (SD ± 11, and prescribing of statins and anti-hypertensives was 51% in each case. Conclusion Results will provide information on changes in diabetes and CVD risk factors and help to inform primary prevention strategies in people with MetS from varied ethnic backgrounds who are at high risk of developing T2DM and CVD. Information gathered in relation to the programme's acceptability and effectiveness in a multi-ethnic population would ensure that our results are widely applicable. Trial registration The study is registered at ClinicalTrials.gov, study identifier: NCT01043770.

  15. Audio segmentation using Flattened Local Trimmed Range for ecological acoustic space analysis

    Directory of Open Access Journals (Sweden)

    Giovany Vega

    2016-06-01

    Full Text Available The acoustic space in a given environment is filled with footprints arising from three processes: biophony, geophony and anthrophony. Bioacoustic research using passive acoustic sensors can result in thousands of recordings. An important component of processing these recordings is to automate signal detection. In this paper, we describe a new spectrogram-based approach for extracting individual audio events. Spectrogram-based audio event detection (AED relies on separating the spectrogram into background (i.e., noise and foreground (i.e., signal classes using a threshold such as a global threshold, a per-band threshold, or one given by a classifier. These methods are either too sensitive to noise, designed for an individual species, or require prior training data. Our goal is to develop an algorithm that is not sensitive to noise, does not need any prior training data and works with any type of audio event. To do this, we propose: (1 a spectrogram filtering method, the Flattened Local Trimmed Range (FLTR method, which models the spectrogram as a mixture of stationary and non-stationary energy processes and mitigates the effect of the stationary processes, and (2 an unsupervised algorithm that uses the filter to detect audio events. We measured the performance of the algorithm using a set of six thoroughly validated audio recordings and obtained a sensitivity of 94% and a positive predictive value of 89%. These sensitivity and positive predictive values are very high, given that the validated recordings are diverse and obtained from field conditions. The algorithm was then used to extract audio events in three datasets. Features of these audio events were plotted and showed the unique aspects of the three acoustic communities.

  16. Deep Sequence Analysis of AgoshRNA Processing Reveals 3’ A Addition and Trimming

    Directory of Open Access Journals (Sweden)

    Alex Harwig

    2015-01-01

    Full Text Available The RNA interference (RNAi pathway, in which microprocessor and Dicer collaborate to process microRNAs (miRNA, was recently expanded by the description of alternative processing routes. In one of these noncanonical pathways, Dicer action is replaced by the Argonaute2 (Ago2 slicer function. It was recently shown that the stem-length of precursor-miRNA or short hairpin RNA (shRNA molecules is a major determinant for Dicer versus Ago2 processing. Here we present the results of a deep sequence study on the processing of shRNAs with different stem length and a top G·U wobble base pair (bp. This analysis revealed some unexpected properties of these so-called AgoshRNA molecules that are processed by Ago2 instead of Dicer. First, we confirmed the gradual shift from Dicer to Ago2 processing upon shortening of the hairpin length. Second, hairpins with a stem larger than 19 base pair are inefficiently cleaved by Ago2 and we noticed a shift in the cleavage site. Third, the introduction of a top G·U bp in a regular shRNA can promote Ago2-cleavage, which coincides with a loss of Ago2-loading of the Dicer-cleaved 3’ strand. Fourth, the Ago2-processed AgoshRNAs acquire a short 3’ tail of 1–3 A-nucleotides (nt and we present evidence that this product is subsequently trimmed by the poly(A-specific ribonuclease (PARN.

  17. Maximising municipal solid waste--legume trimming residue mixture degradation in composting by control parameters optimization.

    Science.gov (United States)

    Cabeza, I O; López, R; Ruiz-Montoya, M; Díaz, M J

    2013-10-15

    Composting is one of the most successful biological processes for the treatment of the residues enriched in putrescible materials. The optimization of parameters which have an influence on the stability of the products is necessary in order to maximize recycling and recovery of waste components. The influence of the composting process parameters (aeration, moisture, C/N ratio, and time) on the stability parameters (organic matter, N-losses, chemical oxygen demand, nitrate, biodegradability coefficient) of the compost was studied. The composting experiment was carried out using Municipal Solid Waste (MSW) and Legume Trimming Residues (LTR) in 200 L isolated acrylic barrels following a Box-Behnken central composite experimental design. Second-order polynomial models were found for each of the studied compost stability parameter, which accurately described the relationship between the parameters. The differences among the experimental values and those estimated by using the equations never exceeded 10% of the former. Results of the modelling showed that excluding the time, the C/N ratio is the strongest variable influencing almost all the stability parameters studied in this case, with the exception of N-losses which is strongly dependent on moisture. Moreover, an optimized ratio MSW/LTR of 1/1 (w/w), moisture content in the range of 40-55% and moderate to low aeration rate (0.05-0.175 Lair kg(-)(1) min(-1)) is recommended to maximise degradation and to obtain a stable product during co-composting of MSW and LTR. Copyright © 2013 Elsevier Ltd. All rights reserved.

  18. Intelligent systems engineering methodology

    Science.gov (United States)

    Fouse, Scott

    1990-01-01

    An added challenge for the designers of large scale systems such as Space Station Freedom is the appropriate incorporation of intelligent system technology (artificial intelligence, expert systems, knowledge-based systems, etc.) into their requirements and design. This presentation will describe a view of systems engineering which successfully addresses several aspects of this complex problem: design of large scale systems, design with requirements that are so complex they only completely unfold during the development of a baseline system and even then continue to evolve throughout the system's life cycle, design that involves the incorporation of new technologies, and design and development that takes place with many players in a distributed manner yet can be easily integrated to meet a single view of the requirements. The first generation of this methodology was developed and evolved jointly by ISX and the Lockheed Aeronautical Systems Company over the past five years on the Defense Advanced Research Projects Agency/Air Force Pilot's Associate Program, one of the largest, most complex, and most successful intelligent systems constructed to date. As the methodology has evolved it has also been applied successfully to a number of other projects. Some of the lessons learned from this experience may be applicable to Freedom.

  19. Evolutionary and Functional Analysis of Old World Primate TRIM5 Reveals the Ancient Emergence of Primate Lentiviruses and Convergent Evolution Targeting a Conserved Capsid Interface.

    Directory of Open Access Journals (Sweden)

    Kevin R McCarthy

    2015-08-01

    Full Text Available The widespread distribution of lentiviruses among African primates, and the lack of severe pathogenesis in many of these natural reservoirs, are taken as evidence for long-term co-evolution between the simian immunodeficiency viruses (SIVs and their primate hosts. Evidence for positive selection acting on antiviral restriction factors is consistent with virus-host interactions spanning millions of years of primate evolution. However, many restriction mechanisms are not virus-specific, and selection cannot be unambiguously attributed to any one type of virus. We hypothesized that the restriction factor TRIM5, because of its unique specificity for retrovirus capsids, should accumulate adaptive changes in a virus-specific fashion, and therefore, that phylogenetic reconstruction of TRIM5 evolution in African primates should reveal selection by lentiviruses closely related to modern SIVs. We analyzed complete TRIM5 coding sequences of 22 Old World primates and identified a tightly-spaced cluster of branch-specific adaptions appearing in the Cercopithecinae lineage after divergence from the Colobinae around 16 million years ago. Functional assays of both extant TRIM5 orthologs and reconstructed ancestral TRIM5 proteins revealed that this cluster of adaptations in TRIM5 specifically resulted in the ability to restrict Cercopithecine lentiviruses, but had no effect (positive or negative on restriction of other retroviruses, including lentiviruses of non-Cercopithecine primates. The correlation between lineage-specific adaptations and ability to restrict viruses endemic to the same hosts supports the hypothesis that lentiviruses closely related to modern SIVs were present in Africa and infecting the ancestors of Cercopithecine primates as far back as 16 million years ago, and provides insight into the evolution of TRIM5 specificity.

  20. Genotyping of TRIM5 locus in northern pig-tailed macaques (Macaca leonina, a primate species susceptible to Human Immunodeficiency Virus type 1 infection

    Directory of Open Access Journals (Sweden)

    Jiang Xue-Long

    2009-06-01

    Full Text Available Abstract Background The pig-tailed macaques are the only Old World monkeys known to be susceptible to human immunodeficiency virus type 1 (HIV-1 infection. We have previously reported that the TRIM5-Cyclophilin A (TRIMCyp fusion in pig-tailed macaques (Macaca nemestrina is dysfunctional in restricting HIV-1, which may explain why pig-tailed macaques are susceptible to HIV-1 infection. Similar results have also been reported by other groups. However, according to the current primate taxonomy, the previously reported M. nemestrina are further classified into three species, which all belong to the Macaca spp. This calls for the need to look into the previous studies in more details. Results The local species Northern pig-tailed macaque (M. leonina was analyzed for the correlation of TRIM5 structure and HIV-1 infection. Eleven M. leonina animals were analyzed, and all of them were found to possess TRIM5-CypA fusion at the TRIM5 locus. The transcripts encoding the dysfunctional TRIM5-CypA should result from the G-to-T mutation in the 3'-splicing site of intron 6. Polymorphism in the putative TRIMCyp recognition domain was observed. The peripheral blood mononuclear cells (PBMCs of M. leonina were susceptible to HIV-1 infection. Consistent with the previous results, expression of the M. leonina TRIMCyp in HeLa-T4 cells rendered the cells resistant to HIV-2ROD but not to SIVmac239 infection. Conclusion The susceptibility of M. leonina to HIV-1 infection is due to the dysfunctional TRIM5-CypA fusion in the TRIM5 locus. This finding should broaden our perspective in developing better HIV/AIDS non-human primate animal models.

  1. Evaluation of agreement among digital dermatitis scoring methods in the milking parlor, pen, and hoof trimming chute.

    Science.gov (United States)

    Cramer, G; Winders, T; Solano, L; Kleinschmit, D H

    2018-03-01

    Digital dermatitis (DD) is the most common infectious foot lesion affecting welfare and productivity of dairy cattle. The key to DD control programs is routine and frequent identification of DD lesions. The objective was to evaluate accuracy of detecting and scoring DD lesions in 3 milking parlor designs and in 3 alternative settings compared with scoring in the hoof trimming chute as reference. A total of 552 cows and 1,104 hind feet from 17 freestall farms were scored by 1 observer in the milking parlor and in 1 other setting: pen, headlocks, or management rail. After being scored in the milking parlor and at least 1 other setting, cows were examined in the hoof trimming chute, considered the gold standard. In every setting, all hind feet were inspected visually using a flashlight and without prior washing of feet. Agreement of the scoring settings was assessed using the 5 M-stage scoring system and a dichotomous absence (M0 or M0/M1) or presence (M1 to M4.1 or M2 to M4.1) system. At trimming chute inspection, 44% of feet had a DD lesion, with estimates of 11, 5, 2, 10, and 16% for M1, M2, M3, M4, and M4.1 lesions, respectively. Apparent DD foot-level prevalence at the milking parlor, pen, management rail, and headlocks was 28, 22, 16, and 22%, respectively. M-stages were less discernible in the pen, management rail, and headlocks (apparent prevalence of M1, M2, M3, and M4.1 was ≤1%) compared with the trimming chute and milking parlor. Agreement beyond chance between any scoring setting and trimming chute scoring ranged from 0.48 to 0.70 for the dichotomous scoring system (absence = M0/M1 vs. presence = M2 to M4.1). Diagnostic test performance varied greatly among DD scoring settings but, in general, it had low sensitivity (93%) for detecting any DD lesion. Agreement and test characteristics were not affected by the type of milking parlor. Although the milking parlor and headlocks were the most reliable settings in which to detect DD, none of the settings were

  2. Neonatal Whisker Trimming Impairs Fear/Anxiety-Related Emotional Systems of the Amygdala and Social Behaviors in Adult Mice.

    Directory of Open Access Journals (Sweden)

    Hitomi Soumiya

    Full Text Available Abnormalities in tactile perception, such as sensory defensiveness, are common features in autism spectrum disorder (ASD. While not a diagnostic criterion for ASD, deficits in tactile perception contribute to the observed lack of social communication skills. However, the influence of tactile perception deficits on the development of social behaviors remains uncertain, as do the effects on neuronal circuits related to the emotional regulation of social interactions. In neonatal rodents, whiskers are the most important tactile apparatus, so bilateral whisker trimming is used as a model of early tactile deprivation. To address the influence of tactile deprivation on adult behavior, we performed bilateral whisker trimming in mice for 10 days after birth (BWT10 mice and examined social behaviors, tactile discrimination, and c-Fos expression, a marker of neural activation, in adults after full whisker regrowth. Adult BWT10 mice exhibited significantly shorter crossable distances in the gap-crossing test than age-matched controls, indicating persistent deficits in whisker-dependent tactile perception. In contrast to controls, BWT10 mice exhibited no preference for the social compartment containing a conspecific in the three-chamber test. Furthermore, the development of amygdala circuitry was severely affected in BWT10 mice. Based on the c-Fos expression pattern, hyperactivity was found in BWT10 amygdala circuits for processing fear/anxiety-related responses to height stress but not in circuits for processing reward stimuli during whisker-dependent cued learning. These results demonstrate that neonatal whisker trimming and concomitant whisker-dependent tactile discrimination impairment severely disturbs the development of amygdala-dependent emotional regulation.

  3. Testing multistage gain and offset trimming in a single photon counting IC with a charge sharing elimination algorithm

    International Nuclear Information System (INIS)

    Krzyżanowska, A.; Gryboś, P.; Szczygieł, R.; Maj, P.

    2015-01-01

    Designing a hybrid pixel detector readout electronics operating in a single photon counting mode is a very challenging process, where many main parameters are optimized in parallel (e.g. gain, noise, and threshold dispersion). Additional requirements for a smaller pixel size with extended functionality push designers to use new deep sub-micron technologies. Minimizing the channel size is possible, however, with a decreased pixel size, the charge sharing effect becomes a more important issue. To overcome this problem, we designed an integrated circuit prototype produced in CMOS 40 nm technology, which has an extended functionality of a single pixel. A C8P1 algorithm for the charge sharing effect compensation was implemented. In the algorithm's first stage the charge is rebuilt in a signal rebuilt hub fed by the CSA (charge sensitive amplifier) outputs from four neighbouring pixels. Then, the pixel with the biggest amount of charge is chosen, after a comparison with all the adjacent ones. In order to process the data in such a complicated way, a certain architecture of a single channel was proposed, which allows for: ⋅ processing the signal with the possibility of total charge reconstruction (by connecting with the adjacent pixels), ⋅ a comparison of certain pixel amplitude to its 8 neighbours, ⋅ the extended testability of each block inside the channel to measure CSA gain dispersion, shaper gain dispersion, threshold dispersion (including the simultaneous generation of different pulse amplitudes from different pixels), ⋅ trimming all the necessary blocks for proper operation. We present a solution for multistage gain and offset trimming implemented in the IC prototype. It allows for minimization of the total charge extraction errors, minimization of threshold dispersion in the pixel matrix and minimization of errors of comparison of certain pixel pulse amplitudes with all its neighbours. The detailed architecture of a single channel is presented

  4. FTR83, a Member of the Large Fish-Specific finTRIM Family, Triggers IFN Pathway and Counters Viral Infection

    Directory of Open Access Journals (Sweden)

    Christelle Langevin

    2017-05-01

    Full Text Available Tripartite motif (TRIM proteins are involved in various cellular functions and constitute key factors of the antiviral innate immune response. TRIM proteins can bind viral particles directly, sending them to degradation by the proteasome, or ubiquitinate signaling molecules leading to upregulation of innate immunity. TRIM proteins are present in across metazoans but are particularly numerous in vertebrates where genes comprising a B30.2 domain have been often duplicated. In fish, a TRIM subset named finTRIM is highly diversified, with large gene numbers and clear signatures of positive selection in the B30.2 domain suggesting they may be involved in antiviral mechanisms. finTRIM provides a beautiful model to investigate the primordial implication of B30.2 TRIM subsets in the arsenal of vertebrate antiviral defenses. We show here that ftr83, a zebrafish fintrim gene mainly expressed in the gills, skin and pharynx, encodes a protein affording a potent antiviral activity. In vitro, overexpression of FTR83, but not of its close relative FTR82, induced IFN and IFN-stimulated gene expression and afforded protection against different enveloped and non-enveloped RNA viruses. The kinetics of IFN induction paralleled the development of the antiviral activity, which was abolished by a dominant negative IRF3 mutant. In the context of a viral infection, FTR83 potentiated the IFN response. Expression of chimeric proteins in which the B30.2 domain of FTR83 and the non-protective FTR82 had been exchanged, showed that IFN upregulation and antiviral activity requires both the Ring/BBox/Coiled coil domain (supporting E3 ubiquitin ligase and the B30.2 domain of FTR83. Finally, loss of function experiments in zebrafish embryos confirms that ftr83 mediates antiviral activity in vivo. Our results show that a member of the largest TRIM subset observed in fish upregulates type I IFN response and afford protection against viral infections, supporting that TRIMs are key

  5. Effect of laceration and trimming of a tendon on the coefficient of friction along the A2 pulley: an in vitro study on turkey tendon.

    Science.gov (United States)

    Hajipour, L; Gulihar, A; Dias, J

    2010-08-01

    We carried out lacerations of 50%, followed by trimming, in ten turkey flexor tendons in vitro and measured the coefficient of friction at the tendon-pulley interface with loads of 200 g and 400 g and in 10 degrees , 30 degrees, 50 degrees and 70 degrees of flexion. Laceration increased the coefficient of friction from 0.12 for the intact tendon to 0.3 at both the test loads. Trimming the laceration reduced the coefficient of friction to 0.2. An exponential increase in the gliding resistance was found at 50 degrees and 70 degrees of flexion (p = 0.02 and p = 0.003, respectively) following trimming compared to that of the intact tendon. We concluded that trimming partially lacerated flexor tendons will reduce the gliding resistance at the tendon-pulley interface, but will lead to fragmentation and triggering of the tendon at higher degrees of flexion and loading. We recommend that higher degrees of flexion be avoided during early post-operative rehabilitation following trimming of a flexor tendon.

  6. Human-animal interactions and safety during dairy cattle handling--Comparing moving cows to milking and hoof trimming.

    Science.gov (United States)

    Lindahl, C; Pinzke, S; Herlin, A; Keeling, L J

    2016-03-01

    Cattle handling is a dangerous activity on dairy farms, and cows are a major cause of injuries to livestock handlers. Even if dairy cows are generally tranquil and docile, when situations occur that they perceive or remember as aversive, they may become agitated and hazardous to handle. This study aimed to compare human-animal interactions, cow behavior, and handler safety when moving cows to daily milking and moving cows to more rarely occurring and possibly aversive hoof trimming. These processes were observed on 12 Swedish commercial dairy farms. The study included behavioral observations of handler and cows and cow heart rate recordings, as well as recording frequencies of situations and incidents related to an increased injury risk to the handler. At milking, cows were quite easily moved using few interactions. As expected, the cows showed no behavioral signs of stress, fear, or resistance and their heart rate only rose slightly from the baseline (i.e., the average heart rate during an undisturbed period before handling). Moving cows to hoof trimming involved more forceful and gentle interactions compared with moving cows to milking. Furthermore, the cows showed much higher frequencies of behaviors indicative of aversion and fear (e.g., freezing, balking, and resistance), as well as a higher increase in heart rate. The risk of injury to which handlers were exposed also increased when moving cows to hoof trimming rather than to routine milking. Some interactions (such as forceful tactile interactions with an object and pulling a neck strap or halter) appeared to be related to potentially dangerous incidents where the handler was being kicked, head-butted, or run over by a cow. In conclusion, moving cows to hoof trimming resulted in higher frequencies of behaviors indicating fear, more forceful interactions, and increased injury risks to the handler than moving cows to milking. Improving potentially stressful handling procedures (e.g., by better animal handling

  7. Air Research

    Science.gov (United States)

    EPA's air research provides the critical science to develop and implement outdoor air regulations under the Clean Air Act and puts new tools and information in the hands of air quality managers and regulators to protect the air we breathe.

  8. Clinical trial methodology

    National Research Council Canada - National Science Library

    Peace, Karl E; Chen, Ding-Geng

    2011-01-01

    ... in the pharmaceutical industry, Clinical trial methodology emphasizes the importance of statistical thinking in clinical research and presents the methodology as a key component of clinical research...

  9. Use of the temporal median and trimmed mean mitigates effects of respiratory motion in multiple-acquisition abdominal diffusion imaging

    International Nuclear Information System (INIS)

    Jerome, N P; Orton, M R; D’Arcy, J A; Leach, M O; Collins, D J; Feiweier, T; Tunariu, N; Koh, D-M

    2015-01-01

    Respiratory motion commonly confounds abdominal diffusion-weighted magnetic resonance imaging, where averaging of successive samples at different parts of the respiratory cycle, performed in the scanner, manifests the motion as blurring of tissue boundaries and structural features and can introduce bias into calculated diffusion metrics. Storing multiple averages separately allows processing using metrics other than the mean; in this prospective volunteer study, median and trimmed mean values of signal intensity for each voxel over repeated averages and diffusion-weighting directions are shown to give images with sharper tissue boundaries and structural features for moving tissues, while not compromising non-moving structures. Expert visual scoring of derived diffusion maps is significantly higher for the median than for the mean, with modest improvement from the trimmed mean. Diffusion metrics derived from mono- and bi-exponential diffusion models are comparable for non-moving structures, demonstrating a lack of introduced bias from using the median. The use of the median is a simple and computationally inexpensive alternative to complex and expensive registration algorithms, requiring only additional data storage (and no additional scanning time) while returning visually superior images that will facilitate the appropriate placement of regions-of-interest when analysing abdominal diffusion-weighted magnetic resonance images, for assessment of disease characteristics and treatment response. (note)

  10. Use of Vine-Trimming Wastes as Carrier for Amycolatopsis sp. to Produce Vanillin, Vanillyl Alcohol, and Vanillic Acid.

    Science.gov (United States)

    Castañón-Rodríguez, Juan Francisco; Pérez-Rodríguez, Noelia; de Souza Oliveira, Ricardo Pinheiro; Aguilar-Uscanga, María Guadalupe; Domínguez, José Manuel

    2016-10-01

    Raw vine-trimming wastes or the solid residues obtained after different fractionation treatments were evaluated for their suitability as Amycolatopsis sp. immobilization carriers during the bioconversion of ferulic acid into valuable phenolic compounds such as vanillin, vanillyl alcohol, and vanillic acid, the main flavor components of vanilla pods. Previously, physical-chemical characteristics of the materials were determined by quantitative acid hydrolysis and water absorption index (WAI), and microbiological characteristics by calculating the cell retention in the carrier (λ). Additionally, micrographics of carrier surface were obtained by field emission-scanning electron microscopy to study the influence of morphological changes during pretreatments in the adhesion of cells immobilized. The results point out that in spite of showing the lowest WAI and intermediate λ, raw material was the most appropriated substrate to conduct the bioconversion, achieving up to 262.9 mg/L phenolic compounds after 24 h, corresponding to 42.9 mg/L vanillin, 115.6 mg/L vanillyl alcohol, and 104.4 mg/L vanillic acid. The results showed the potential of this process to be applied for biotechnological production of vanillin from ferulic acid solutions; however, further studies must be carried out to increase vanillin yield. Additionally, the liquors obtained after treatment of vine-trimming wastes could be assayed to replace synthetic ferulic acid.

  11. Concerted in vitro trimming of viral HLA-B27-restricted ligands by human ERAP1 and ERAP2 aminopeptidases.

    Directory of Open Access Journals (Sweden)

    Elena Lorente

    Full Text Available In the classical human leukocyte antigen (HLA class I antigen processing and presentation pathway, the antigenic peptides are generated from viral proteins by multiple proteolytic cleavages of the proteasome (and in some cases other cytosolic proteases and transported to the endoplasmic reticulum (ER lumen where they are exposed to aminopeptidase activity. In human cells, two different ER-resident enzymes, ERAP1 and ERAP2, can trim the N-terminally extended residues of peptide precursors. In this study, the possible cooperative effect of generating five naturally processed HLA-B27 ligands by both proteases was analyzed. We identified differences in the products obtained with increased detection of natural HLA-B27 ligands by comparing double versus single enzyme digestions by mass spectrometry analysis. These in vitro data suggest that each enzyme can use the degradation products of the other as a substrate for new N-terminal trimming, indicating concerted aminoproteolytic activity of ERAP 1 and ERAP2.

  12. Effects of Beak Trimming, Stocking Density and Sex on Carcass Yield, Carcass Components, Plasma Glucose and Triglyceride Levels in Large White Turkeys

    Science.gov (United States)

    Kiraz, Selahattin

    2015-01-01

    This study was conducted to determine the effects of beak trimming, stocking density (D) and sex (S) on live weight (LW), carcass yield and its component, and plasma glucose (PG) and triglyceride levels in Large White turkeys. To accomplish this aims, totally 288 d old large white turkey chicks (144 in each sex) were used. Beaks of 77 male and female poults were trimmed when 8 d old with an electrical beak trimmer. The birds were fed by commercial turkey rasion. Experiment was designed as 2 × 2 × 2 factorial arrangement with 3 replications in each group. Beak trimming and stocking density did not affect live weight, carcass composition and its components. The higher LW and carcass weight observed in trimmed groups. As expected, male birds are heavier than female, and carcass percentage (CP) would be adverse. However, in this study, CP of male was higher in trimmed, in 0.25 m2/bird. (D) × sex (S) interaction had an effect on both CP and thigh weights (pcarcass and its some components were higher in male. S × D interaction had an effect on plasma glucose level (p<0.05). Triglyceride level was affected (p<0.05) by sex. Significant relationships were found between percentage of thighs (r=0.447, p<0.01) and percentage of breast (r=0.400, p<0.01). According to this study, it can be said that trimming is useful with density of 0.25 m2/bird in turkey fattening. PMID:26877630

  13. Air Pollution

    Science.gov (United States)

    Air pollution is a mixture of solid particles and gases in the air. Car emissions, chemicals from factories, ... Ozone, a gas, is a major part of air pollution in cities. When ozone forms air pollution, it's ...

  14. Methodology for building confidence measures

    Science.gov (United States)

    Bramson, Aaron L.

    2004-04-01

    This paper presents a generalized methodology for propagating known or estimated levels of individual source document truth reliability to determine the confidence level of a combined output. Initial document certainty levels are augmented by (i) combining the reliability measures of multiply sources, (ii) incorporating the truth reinforcement of related elements, and (iii) incorporating the importance of the individual elements for determining the probability of truth for the whole. The result is a measure of confidence in system output based on the establishing of links among the truth values of inputs. This methodology was developed for application to a multi-component situation awareness tool under development at the Air Force Research Laboratory in Rome, New York. Determining how improvements in data quality and the variety of documents collected affect the probability of a correct situational detection helps optimize the performance of the tool overall.

  15. Preventing Work-Related Musculoskeletal Illnesses Through Ergonomics: The Air Force PREMIER Program, Volume 4B: Research Report For Level I Ergonomics Methodology Guide For Maintenance/Inspection Work Areas

    National Research Council Canada - National Science Library

    Barker, Richard

    1997-01-01

    ... (both technicians and consensus ergonomists) and the Gold Standard ergonomist. High duration tasks were more likely to be rated high risk by the Level I Methodology, whereas jobs with multiple, moderate duration tasks were more likely to be rated medium risk.

  16. Evaluation of the sanitary impact of urban air pollution. Update version of the methodological guide; Evaluation de l'impact sanitaire de la pollution atmospherique urbaine. Version actualisee du guide methodologique

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-03-15

    In order to bring a help to the evaluation of effects of air quality on health, the Institute of Sanitary surveillance published in 1999 a method guide for the realisation of sanitary impact evaluations of the urban air pollution. This work to prepare to an update version of the guide presents the first recommendations that can be made today for the realisation of sanitary impact evaluations at short and long term at a local level, taking into account the knowledge evolution. (N.C.)

  17. A canopy trimming experiment in Puerto Rico: the response of litter invertebrate communities to canopy loss and debris deposition in a tropical forest subject to hurricanes

    Science.gov (United States)

    Barbara A. Richardson; Michael J. Richardson; Grizelle Gonzalez; Aaron B. Shiels; Diane S. Srivastava

    2010-01-01

    Hurricanes cause canopy removal and deposition of pulses of litter to the forest floor. A Canopy Trimming Experiment (CTE) was designed to decouple these two factors, and to investigate the separate abiotic and biotic consequences of hurricane-type damage and monitor recovery processes. As part of this experiment, effects on forest floor invertebrate communities were...

  18. 77 FR 58091 - Risk-Based Sampling of Beef Manufacturing Trimmings for Escherichia coli (E. coli) O157:H7 and...

    Science.gov (United States)

    2012-09-19

    ... for exposure of carcasses and parts to any contamination or food safety hazard during the removal of... DEPARTMENT OF AGRICULTURE Food Safety and Inspection Service [Docket No. FSIS-2012-0020] Risk-Based Sampling of Beef Manufacturing Trimmings for Escherichia coli (E. coli) O157:H7 and Plans for Beef...

  19. Snavelbehandeling in de kalkoenhouderij : alternatieven via fokkerij en bedrijfsmanagemrnt = Beak trimming in turkey production : alternatives by means of breeding and farm management

    NARCIS (Netherlands)

    Veldkamp, T.

    2010-01-01

    A literature review on effects of breeding and management on injurious pecking behaviour and cannibalism has been conducted. The combination of factors to avoid injurious behaviour is not clear and thus no good alternative to beak trimming of the upper beak in day-old turkey poults is available. If

  20. Application of the concept of dynamic trim control to automatic landing of carrier aircraft. [utilizing digital feedforeward control

    Science.gov (United States)

    Smith, G. A.; Meyer, G.

    1980-01-01

    The results of a simulation study of an alternative design concept for an automatic landing control system are presented. The alternative design concept for an automatic landing control system is described. The design concept is the total aircraft flight control system (TAFCOS). TAFCOS is an open loop, feed forward system that commands the proper instantaneous thrust, angle of attack, and roll angle to achieve the forces required to follow the desired trajector. These dynamic trim conditions are determined by an inversion of the aircraft nonlinear force characteristics. The concept was applied to an A-7E aircraft approaching an aircraft carrier. The implementation details with an airborne digital computer are discussed. The automatic carrier landing situation is described. The simulation results are presented for a carrier approach with atmospheric disturbances, an approach with no disturbances, and for tailwind and headwind gusts.

  1. A Noise Trimming and Positional Significance of Transposon Insertion System to Identify Essential Genes in Yersinia pestis

    Science.gov (United States)

    Yang, Zheng Rong; Bullifent, Helen L.; Moore, Karen; Paszkiewicz, Konrad; Saint, Richard J.; Southern, Stephanie J.; Champion, Olivia L.; Senior, Nicola J.; Sarkar-Tyson, Mitali; Oyston, Petra C. F.; Atkins, Timothy P.; Titball, Richard W.

    2017-02-01

    Massively parallel sequencing technology coupled with saturation mutagenesis has provided new and global insights into gene functions and roles. At a simplistic level, the frequency of mutations within genes can indicate the degree of essentiality. However, this approach neglects to take account of the positional significance of mutations - the function of a gene is less likely to be disrupted by a mutation close to the distal ends. Therefore, a systematic bioinformatics approach to improve the reliability of essential gene identification is desirable. We report here a parametric model which introduces a novel mutation feature together with a noise trimming approach to predict the biological significance of Tn5 mutations. We show improved performance of essential gene prediction in the bacterium Yersinia pestis, the causative agent of plague. This method would have broad applicability to other organisms and to the identification of genes which are essential for competitiveness or survival under a broad range of stresses.

  2. Effects of enzymatic hydrolysis and ultrasounds pretreatments on corn cob and vine trimming shoots for biogas production.

    Science.gov (United States)

    Pérez-Rodríguez, N; García-Bernet, D; Domínguez, J M

    2016-12-01

    Due to their lignocellulosic nature, corn cob and vine trimming shoots (VTS) could be valorized by anaerobic digestion for biogas production. To enhance the digestibility of substrates, pretreatments of lignocellulosic materials are recommended. The effect of enzymatic hydrolysis, ultrasounds pretreatments (US) and the combination of both was assayed in lignocellulosic composition, methane, and biogas yields. The pretreatments leaded to a reduction in lignin and an increase in neutral detergent soluble compounds making corn cob and VTS more amendable for biogas conversion. The US were negative for biogas production from both substrates and in particular strongly detrimental for VTS. On the opposite side, the enzymatic hydrolysis was certainly beneficial increasing 59.8% and 14.6% the methane production from VTS and corn cob, respectively. The prior application of US did not potentiate (or not sufficiently) the improvement in the methane production reflected by the enzymatic hydrolysis pretreatment of VTS and corn cob. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. New gene evolution in the bonus-TIF1-γ/TRIM33 family impacted the architecture of the vertebrate dorsal-ventral patterning network.

    Science.gov (United States)

    Wisotzkey, Robert G; Quijano, Janine C; Stinchfield, Michael J; Newfeld, Stuart J

    2014-09-01

    Uncovering how a new gene acquires its function and understanding how the function of a new gene influences existing genetic networks are important topics in evolutionary biology. Here, we demonstrate nonconservation for the embryonic functions of Drosophila Bonus and its newest vertebrate relative TIF1-γ/TRIM33. We showed previously that TIF1-γ/TRIM33 functions as an ubiquitin ligase for the Smad4 signal transducer and antagonizes the Bone Morphogenetic Protein (BMP) signaling network underlying vertebrate dorsal-ventral axis formation. Here, we show that Bonus functions as an agonist of the Decapentaplegic (Dpp) signaling network underlying dorsal-ventral axis formation in flies. The absence of conservation for the roles of Bonus and TIF1-γ/TRIM33 reveals a shift in the dorsal-ventral patterning networks of flies and mice, systems that were previously considered wholly conserved. The shift occurred when the new gene TIF1-γ/TRIM33 replaced the function of the ubiquitin ligase Nedd4L in the lineage leading to vertebrates. Evidence of this replacement is our demonstration that Nedd4 performs the function of TIF1-γ/TRIM33 in flies during dorsal-ventral axis formation. The replacement allowed vertebrate Nedd4L to acquire novel functions as a ubiquitin ligase of vertebrate-specific Smad proteins. Overall our data reveal that the architecture of the Dpp/BMP dorsal-ventral patterning network continued to evolve in the vertebrate lineage, after separation from flies, via the incorporation of new genes. © The Author 2014. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  4. Coupling two sizes of CSTR-type bioreactors for sequential lactic acid and xylitol production from hemicellulosic hydrolysates of vineshoot trimmings.

    Science.gov (United States)

    Salgado, José Manuel; Rodríguez, Noelia; Cortés, Sandra; Domínguez, José Manuel

    2012-02-15

    This study develops a system for the efficient valorisation of hemicellulosic hydrolysates of vineshoot trimmings. By connecting two reactors of 2L and 10L, operational conditions were set up for the sequential production of lactic acid and xylitol in continuous fermentation, considering the dependence of the main metabolites and fermentation parameters on the dilution rate. In the first bioreactor, Lactobacillus rhamnosus consumed all the glucose to produce lactic acid at 31.5°C, with 150rpm and 1L of working volume as the optimal conditions. The residual sugars were employed for the xylose to xylitol bioconversion by Debaryomyces hansenii in the second bioreactor at 30°C, 250rpm and an air-flow rate of 2Lmin(-1). Several steady states were reached at flow rates (F) in the range of 0.54-5.33mLmin(-1), leading to dilution rates (D) ranging from 0.032 to 0.320h(-1) in Bioreactor 1 and from 0.006 to 0.064h(-1) in Bioreactor 2. The maximum volumetric lactic acid productivity (Q(P LA)=2.908gL(-1)h(-1)) was achieved under D=0.266h(-1) (F=4.44mLmin(-1)); meanwhile, the maximum production of xylitol (5.1gL(-1)), volumetric xylitol productivity (Q(P xylitol)=0.218gL(-1)h(-1)), volumetric rate of xylose consumption (Q(S xylose)=0.398gL(-1)h(-1)) and product yield (0.55gg(-1)) were achieved at an intermediate dilution rate of 0.043h(-1) (F=3.55mLmin(-1)). Under these conditions, ethanol, which was the main by-product of the fermentation, was produced in higher amounts (1.9gL(-1)). Finally, lactic acid and xylitol were effectively recovered by conventional procedures. Copyright © 2011 Elsevier B.V. All rights reserved.

  5. Released air during vapor and air cavitation

    Energy Technology Data Exchange (ETDEWEB)

    Jablonská, Jana, E-mail: jana.jablonska@vsb.cz; Kozubková, Milada, E-mail: milada.kozubkova@vsb.cz [VŠB-Technical University of Ostrava, Faculty of Mechanical Engineering, Department of Hydromechanics and Hydraulic Equipment, 17. listopadu 15, 708 33 Ostrava-Poruba (Czech Republic)

    2016-06-30

    Cavitation today is a very important problem that is solved by means of experimental and mathematical methods. The article deals with the generation of cavitation in convergent divergent nozzle of rectangular cross section. Measurement of pressure, flow rate, temperature, amount of dissolved air in the liquid and visualization of cavitation area using high-speed camera was performed for different flow rates. The measurement results were generalized by dimensionless analysis, which allows easy detection of cavitation in the nozzle. For numerical simulation the multiphase mathematical model of cavitation consisting of water and vapor was created. During verification the disagreement with the measurements for higher flow rates was proved, therefore the model was extended to multiphase mathematical model (water, vapor and air), due to release of dissolved air. For the mathematical modeling the multiphase turbulence RNG k-ε model for low Reynolds number flow with vapor and air cavitation was used. Subsequently the sizes of the cavitation area were verified. In article the inlet pressure and loss coefficient depending on the amount of air added to the mathematical model are evaluated. On the basis of the approach it may be create a methodology to estimate the amount of released air added at the inlet to the modeled area.

  6. Air Abrasion

    Science.gov (United States)

    ... Chapters What Is Air Abrasion? What Happens? The Pros and Cons Will I Feel Anything? Is Air ... will perform any procedures that use air-abrasion technology. Ask your dentist if he or she uses ...

  7. Design and analysis of biomimetic joints for morphing of micro air vehicles.

    Science.gov (United States)

    Grant, Daniel T; Abdulrahim, Mujahid; Lind, Rick

    2010-12-01

    Flight capability for micro air vehicles is rapidly maturing throughout the aviation community; however, mission capability has not yet matured at the same pace. Maintaining trim during a descent or in the presence of crosswinds remains challenging for fixed-wing aircraft but yet is routinely performed by birds. This paper presents an overview of designs that incorporate morphing to enhance their flight characteristics. In particular, a series of joints and structures is adopted from seagulls to alter either the dihedral or sweep of the wings and thus alter the flight characteristics. The resulting vehicles are able to trim with significantly increased angles of attack and sideslip compared to traditional fixed-wing vehicles.

  8. Design and analysis of biomimetic joints for morphing of micro air vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Grant, Daniel T; Abdulrahim, Mujahid; Lind, Rick, E-mail: ricklind@ufl.ed [Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, FL 32611 (United States)

    2010-12-15

    Flight capability for micro air vehicles is rapidly maturing throughout the aviation community; however, mission capability has not yet matured at the same pace. Maintaining trim during a descent or in the presence of crosswinds remains challenging for fixed-wing aircraft but yet is routinely performed by birds. This paper presents an overview of designs that incorporate morphing to enhance their flight characteristics. In particular, a series of joints and structures is adopted from seagulls to alter either the dihedral or sweep of the wings and thus alter the flight characteristics. The resulting vehicles are able to trim with significantly increased angles of attack and sideslip compared to traditional fixed-wing vehicles.

  9. Design and analysis of biomimetic joints for morphing of micro air vehicles

    International Nuclear Information System (INIS)

    Grant, Daniel T; Abdulrahim, Mujahid; Lind, Rick

    2010-01-01

    Flight capability for micro air vehicles is rapidly maturing throughout the aviation community; however, mission capability has not yet matured at the same pace. Maintaining trim during a descent or in the presence of crosswinds remains challenging for fixed-wing aircraft but yet is routinely performed by birds. This paper presents an overview of designs that incorporate morphing to enhance their flight characteristics. In particular, a series of joints and structures is adopted from seagulls to alter either the dihedral or sweep of the wings and thus alter the flight characteristics. The resulting vehicles are able to trim with significantly increased angles of attack and sideslip compared to traditional fixed-wing vehicles.

  10. Methodology for estimating sodium aerosol concentrations during breeder reactor fires

    International Nuclear Information System (INIS)

    Fields, D.E.; Miller, C.W.

    1985-01-01

    We have devised and applied a methodology for estimating the concentration of aerosols released at building surfaces and monitored at other building surface points. We have used this methodology to make calculations that suggest, for one air-cooled breeder reactor design, cooling will not be compromised by severe liquid-metal fires

  11. Scenario development methodologies

    International Nuclear Information System (INIS)

    Eng, T.; Hudson, J.; Stephansson, O.

    1994-11-01

    In the period 1981-1994, SKB has studied several methodologies to systematize and visualize all the features, events and processes (FEPs) that can influence a repository for radioactive waste in the future. All the work performed is based on the terminology and basic findings in the joint SKI/SKB work on scenario development presented in the SKB Technical Report 89-35. The methodologies studied are a) Event tree analysis, b) Influence diagrams and c) Rock Engineering Systems (RES) matrices. Each one of the methodologies is explained in this report as well as examples of applications. One chapter is devoted to a comparison between the two most promising methodologies, namely: Influence diagrams and the RES methodology. In conclusion a combination of parts of the Influence diagram and the RES methodology is likely to be a promising approach. 26 refs

  12. Reliability Centered Maintenance - Methodologies

    Science.gov (United States)

    Kammerer, Catherine C.

    2009-01-01

    Journal article about Reliability Centered Maintenance (RCM) methodologies used by United Space Alliance, LLC (USA) in support of the Space Shuttle Program at Kennedy Space Center. The USA Reliability Centered Maintenance program differs from traditional RCM programs because various methodologies are utilized to take advantage of their respective strengths for each application. Based on operational experience, USA has customized the traditional RCM methodology into a streamlined lean logic path and has implemented the use of statistical tools to drive the process. USA RCM has integrated many of the L6S tools into both RCM methodologies. The tools utilized in the Measure, Analyze, and Improve phases of a Lean Six Sigma project lend themselves to application in the RCM process. All USA RCM methodologies meet the requirements defined in SAE JA 1011, Evaluation Criteria for Reliability-Centered Maintenance (RCM) Processes. The proposed article explores these methodologies.

  13. Research note: the performance of spring- and summer-reared broilers as affected by precision beak trimming at seven days of age.

    Science.gov (United States)

    Christmas, R B

    1993-12-01

    In each of two duplicate trials approximately 2,500 day-old Peterson x Arbor Acres straight-run broiler chicks were equally divided between two treatments of three pens each. Treatment 1 was maintained as controls (C), and Treatment 2 birds were precision beak-trimmed (PBT) at 7 days of age. Feed and water were supplied for ad libitum consumption to both groups. Trials 1 and 2 were initiated in March and June, respectively. Performance of spring-reared broilers were comparable regardless of beak trimming procedure, except that PBT broilers experienced slightly higher mortality after PBT. Final body weights of the summer-reared broilers were 15% lower than those reared in the spring. Additionally, PBT resulted in significantly reduced final body weights and feed intake. There were no significant differences in mortality or feed conversion due to PBT.

  14. Introduction to LCA Methodology

    DEFF Research Database (Denmark)

    Hauschild, Michael Z.

    2018-01-01

    In order to offer the reader an overview of the LCA methodology in the preparation of the more detailed description of its different phases, a brief introduction is given to the methodological framework according to the ISO 14040 standard and the main elements of each of its phases. Emphasis...

  15. Methodologies, languages and tools

    International Nuclear Information System (INIS)

    Amako, Katsuya

    1994-01-01

    This is a summary of the open-quotes Methodologies, Languages and Toolsclose quotes session in the CHEP'94 conference. All the contributions to methodologies and languages are relevant to the object-oriented approach. Other topics presented are related to various software tools in the down-sized computing environment

  16. Archetype modeling methodology.

    Science.gov (United States)

    Moner, David; Maldonado, José Alberto; Robles, Montserrat

    2018-03-01

    Clinical Information Models (CIMs) expressed as archetypes play an essential role in the design and development of current Electronic Health Record (EHR) information structures. Although there exist many experiences about using archetypes in the literature, a comprehensive and formal methodology for archetype modeling does not exist. Having a modeling methodology is essential to develop quality archetypes, in order to guide the development of EHR systems and to allow the semantic interoperability of health data. In this work, an archetype modeling methodology is proposed. This paper describes its phases, the inputs and outputs of each phase, and the involved participants and tools. It also includes the description of the possible strategies to organize the modeling process. The proposed methodology is inspired by existing best practices of CIMs, software and ontology development. The methodology has been applied and evaluated in regional and national EHR projects. The application of the methodology provided useful feedback and improvements, and confirmed its advantages. The conclusion of this work is that having a formal methodology for archetype development facilitates the definition and adoption of interoperable archetypes, improves their quality, and facilitates their reuse among different information systems and EHR projects. Moreover, the proposed methodology can be also a reference for CIMs development using any other formalism. Copyright © 2018 Elsevier Inc. All rights reserved.

  17. Menopause and Methodological Doubt

    Science.gov (United States)

    Spence, Sheila

    2005-01-01

    Menopause and methodological doubt begins by making a tongue-in-cheek comparison between Descartes' methodological doubt and the self-doubt that can arise around menopause. A hermeneutic approach is taken in which Cartesian dualism and its implications for the way women are viewed in society are examined, both through the experiences of women…

  18. VEM: Virtual Enterprise Methodology

    DEFF Research Database (Denmark)

    Tølle, Martin; Vesterager, Johan

    2003-01-01

    This chapter presents a virtual enterprise methodology (VEM) that outlines activities to consider when setting up and managing virtual enterprises (VEs). As a methodology the VEM helps companies to ask the right questions when preparing for and setting up an enterprise network, which works...

  19. Data Centric Development Methodology

    Science.gov (United States)

    Khoury, Fadi E.

    2012-01-01

    Data centric applications, an important effort of software development in large organizations, have been mostly adopting a software methodology, such as a waterfall or Rational Unified Process, as the framework for its development. These methodologies could work on structural, procedural, or object oriented based applications, but fails to capture…

  20. The Methodology of Magpies

    Science.gov (United States)

    Carter, Susan

    2014-01-01

    Arts/Humanities researchers frequently do not explain methodology overtly; instead, they "perform" it through their use of language, textual and historic cross-reference, and theory. Here, methodologies from literary studies are shown to add to Higher Education (HE) an exegetical and critically pluralist approach. This includes…

  1. PRODUCT SAFETY AND COLOR CHARACTERISTICS OF GROUND BEEF PROCESSED FROM BEEF TRIMMINGS TREATED WITH PEROXYACETIC ACID ALONE OR FOLLOWED BY NOVEL ORGANIC ACIDS

    Directory of Open Access Journals (Sweden)

    Fred Pohlman

    2014-10-01

    Full Text Available The objective of this study was to evaluate the effectiveness of antimicrobial interventions using peroxyacetic acetic acid (PAA followed by novel organic acids on beef trimmings prior to grinding with conventional spray (CS or electrostatic spray (ES on ground beef microbial populations and color. Beef trimmings (80/20; 25kg were inoculated with E. coli O157:H7, non- O157:H7 shiga toxin producing (STEC E. coli (EC and Salmonella spp. (SA at 105 CFU/g. Inoculated trimmings (1.5 kg /treatment/replicate, 2 replicates were treated with CS application of 0.02% PAA alone or followed by CS or ES application of 3% octanoic acid (PO, 3% pyruvic acid (PP, 3% malic acid (PM, saturated solution of fumaric acid (PF or deionized water (W. Findings from this study suggest that PA as a single or multiple chemical hurdle approach with malic, pyruvic, octanoic and fumaric acid on beef trimmings may be effective in reducing E. coli O157:H7 as well as non-STEC serotypes and Salmonella in ground beef up to day 2 of simulated retail display. Results of this study showed that instrumental color properties of ground beef treated with peroxyacetic acid followed by organic acids had little or no difference (P > 0.05 compared to the untreated un-inoculated control ground beef samples. The results also indicate that ES application of some organic acids may have similar or greater efficiency in controlling ground beef microbial populations compared to the CS application of the same acid providing a more economical and waste manageable decontamination approach.

  2. Design of a Rad-Hard eFuse Trimming Circuit for Bandgap Voltage Reference for LHC Experiments Upgrades

    CERN Document Server

    Besirli, Mustafa; Koukab, Adil; Michelis, Stefano

    A precise and stable reference voltage is required to generate a stable output voltage in DC/DC converters. This reference voltage must be independent of temperature, power supply, radiation, intrinsic technology mismatch and process variation. This master's thesis reports the development of a rad-hard bandgap voltage reference with electrical fuse (eFuse) based analog calibration circuit in a commercial 130nm technology. According to the test results, the maximum error in the bandgap voltage (300mV in this application) was reduced from ±30mV to less than ±0.6mV thanks to the eFuse trimming. A temperature, power supply, radiation, mismatch and process-independent reference voltage was generated to provide reference voltage to first (bPOL12V) and second (bPOL2V5) stage DC/DC converters. This circuit will be integrated in bPOL12V and bPOL2V5 converters for high-luminosity LHC upgrades.

  3. Longitudinal Trim and Tumble Characteristics of a 0.057-Scale Model of the Chance Vought XF7U-1 Airplane, TED NO. NACA DE311

    Science.gov (United States)

    Bryant, Robert L.

    1948-01-01

    Based on results of longitudinal trim and tumble tests of a 0.057-scale model of the Chance Vought XF7U-1 airplane, the following conclusions regarding the trim and tumble characteristics of the airplane have been drawn: 1. The airplane will not trim at any unusual or uncontrolled angles of attack. 2. The airplane will not tumble with the center of gravity located forward of 24 percent of the mean aerodynamic chord. When the center of gravity is located at 24 percent of the mean aerodynamic chord and slats are extended and elevators are deflected full up, the airplane may tumble if given an external positive pitching moment. 3. The tumbling motion obtained will be readily terminated by deflecting the elevators full down so as to oppose the rotation. 4. The accelerations encountered during an established tumble may be dangerous to the pilot and, therefore, action should be taken to terminate a tumble immediately upon its inception. 5. Simultaneous opening of two wing-tip parachutes having diameters of 4 feet or larger and having drag coefficients of approximately 0.7 will effectively terminate the tumble. 6. Model results indicate that the pilot will not be struck by the airplane if it becomes necessary to leave the airplane during a tumble. The pilot may require aid from an ejection-seat arrangement.

  4. Air Quality Modelling and the National Emission Database

    DEFF Research Database (Denmark)

    Jensen, S. S.

    The project focuses on development of institutional strengthening to be able to carry out national air emission inventories based on the CORINAIR methodology. The present report describes the link between emission inventories and air quality modelling to ensure that the new national air emission...... inventory is able to take into account the data requirements of air quality models...

  5. Paint this pipeline green : new pipeline technologies set to trim fugitive emissions, reuse waste heat

    Energy Technology Data Exchange (ETDEWEB)

    Cope, G.

    2007-01-15

    A significant amount of methane is released when natural gas is moved through North American pipelines, and gas producers continue to search for a method to recapture energy wasted as a result of the pressure reductions needed to deliver natural gas to residential areas. This article provided details of a new direct fuel cell energy recovery generation unit (DFC-ERG) consisting of a 1.2 MW fuel cell and a 1 MW unfired gas expansion turbine. As the natural gas exits the high pressure mainline, it passes through the unfired turbine, which rotates a generator and produces electricity. The fuel cell then uses an electrochemical process to internally convert natural gas to hydrogen, which is then converted into electricity and heat. The combined system can achieve electrical efficiencies of more than 60 per cent, and has almost no emissions. Heat produced by the fuel cell can be captured and used to warm up the gas in the distribution network in order to offset boiler emissions. Designed by Enbridge, the system is expected to be in operation by 2008, and will provide up to 15,000 MW hours per year. TransCanada Corporation has designed a supersonic gas-gas ejector that fits around the turbine shafts that release small amounts of gas to prevent heat build-up at compressor stations. The device encapsulates the gas, which is then re-injected back into the mainline, and may save the company up to 0.5 bcf per year. In Alberta, many portable compressor engines waste as much as 30 per cent of their efficiency through exhaust gases. A 3 year research project has resulted in the design of a slug flow generator. Water from a large tub is pumped into the top of a transparent acrylic cylinder which creates a vortex. Compressed air is then injected into the top of the vortex, where it breaks down into discrete slugs of water. While still in the initial design phases, the device may be used for field compressor exhaust pipes, as well as for commercial and residential applications. 2

  6. A single amino acid of human immunodeficiency virus type 2 capsid protein affects conformation of two external loops and viral sensitivity to TRIM5α.

    Directory of Open Access Journals (Sweden)

    Tadashi Miyamoto

    Full Text Available We previously reported that human immunodeficiency virus type 2 (HIV-2 carrying alanine or glutamine but not proline at position 120 of the capsid protein (CA could grow in the presence of anti-viral factor TRIM5α of cynomolgus monkey (CM. To elucidate details of the interaction between the CA and TRIM5α, we generated mutant HIV-2 viruses, each carrying one of the remaining 17 possible amino acid residues, and examined their sensitivity to CM TRIM5α-mediated restriction. Results showed that hydrophobic residues or those with ring structures were associated with sensitivity, while those with small side chains or amide groups conferred resistance. Molecular dynamics simulation study revealed a structural basis for the differential TRIM5α sensitivities. The mutations at position 120 in the loop between helices 6 and 7 (L6/7 affected conformation of the neighboring loop between helices 4 and 5 (L4/5, and sensitive viruses had a common L4/5 conformation. In addition, the common L4/5 structures of the sensitive viruses were associated with a decreased probability of hydrogen bond formation between the 97th aspartic acid in L4/5 and the 119th arginine in L6/7. When we introduced aspartic acid-to-alanine substitution at position 97 (D97A of the resistant virus carrying glutamine at position 120 to disrupt hydrogen bond formation, the resultant virus became moderately sensitive. Interestingly, the virus carrying glutamic acid at position 120 showed resistance, while its predicted L4/5 conformation was similar to those of sensitive viruses. The D97A substitution failed to alter the resistance of this particular virus, indicating that the 120th amino acid residue itself is also involved in sensitivity regardless of the L4/5 conformation. These results suggested that a hydrogen bond between the L4/5 and L6/7 modulates the overall structure of the exposed surface of the CA, but the amino acid residue at position 120 is also directly involved in CM TRIM5

  7. Toll-like receptor 3 stimulation promotes Ro52/TRIM21 synthesis and nuclear redistribution in salivary gland epithelial cells, partially via type I interferon pathway

    Science.gov (United States)

    Kyriakidis, N C; Kapsogeorgou, E K; Gourzi, V C; Konsta, O D; Baltatzis, G E; Tzioufas, A G

    2014-01-01

    Up-regulated expression of Ro52/tripartite motif-containing protein 21 (TRIM21), Ro60/TROVE domain family, member 2 (TROVE2) and lupus LA protein/Sjögren's syndrome antigen B (La/SSB) autoantigens has been described in the salivary gland epithelial cells (SGEC) of patients with Sjögren's syndrome (SS). SGECs, the key regulators of autoimmune SS responses, express high levels of surface functional Toll-like receptor (TLR)-3, whereas Ro52/TRIM21 negatively regulates TLR-3-mediated inflammation. Herein, we investigated the effect of TLR-3-signalling on the expression of Ro52/TRIM21, as well as Ro60/TROVE2 and La/SSB autoantigens, by SGECs. The effect of TLR-3 or TLR-4 stimulation on autoantigen expression was evaluated by polyI:C or lipopolysaccharide (LPS) treatment, respectively, of SGEC lines (10 from SS patients, 12 from non-SS controls) or HeLa cells, followed by analysis of mRNA and protein expression. PolyI:C, but not LPS, resulted in a two-step induction of Ro52/TRIM21 mRNA expression by SGECs, a 12-fold increment at 6 h followed by a 2·5-fold increment at 24–48 h, whereas it induced a late two-fold up-regulation of Ro60/TROVE2 and La/SSB mRNAs at 48 h. Although protein expression levels were not affected significantly, the late up-regulation of Ro52/TRIM21 mRNA was accompanied by protein redistribution, from nucleolar-like pattern to multiple coarse dots spanning throughout the nucleus. These late phenomena were mediated significantly by interferon (IFN)-β production, as attested by cognate secretion and specific inhibition experiments and associated with IFN regulatory factor (IRF)3 degradation. TLR-3-signalling had similar effects on SGECs obtained from SS patients and controls, whereas it did not affect the expression of these autoantigens in HeLa cells. TLR-3 signalling regulates the expression of autoantigens by SGECs, implicating innate immunity pathways in their over-expression in inflamed tissues and possibly in their exposure to the immune

  8. Radioisotope methodology course radioprotection aspects

    International Nuclear Information System (INIS)

    Bergoc, R.M.; Caro, R.A.; Menossi, C.A.

    1996-01-01

    The advancement knowledge in molecular and cell biology, biochemistry, medicine and pharmacology, which has taken place during the last 50 years, after World War II finalization, is really outstanding. It can be safely said that this fact is principally due to the application of radioisotope techniques. The research on metabolisms, biodistribution of pharmaceuticals, pharmacodynamics, etc., is mostly carried out by means of techniques employing radioactive materials. Radioisotopes and radiation are frequently used in medicine both as diagnostic and therapeutic tools. The radioimmunoanalysis is today a routine method in endocrinology and in general clinical medicine. The receptor determination and characterization is a steadily growing methodology used in clinical biochemistry, pharmacology and medicine. The use of radiopharmaceuticals and radiation of different origins, for therapeutic purposes, should not be overlooked. For these reasons, the importance to teach radioisotope methodology is steadily growing. This is principally the case for specialization at the post-graduate level but at the pre graduate curriculum it is worthwhile to give some elementary theoretical and practical notions on this subject. These observations are justified by a more than 30 years teaching experience at both levels at the School of Pharmacy and Biochemistry of the University of Buenos Aires, Argentina. In 1960 we began to teach Physics III, an obligatory pregraduate course for biochemistry students, in which some elementary notions of radioactivity and measurement techniques were given. Successive modifications of the biochemistry pregraduate curriculum incorporated radiochemistry as an elective subject and since 1978, radioisotope methodology, as obligatory subject for biochemistry students. This subject is given at the radioisotope laboratory during the first semester of each year and its objective is to provide theoretical and practical knowledge to the biochemistry students, even

  9. Geostatistical models for air pollution

    International Nuclear Information System (INIS)

    Pereira, M.J.; Soares, A.; Almeida, J.; Branquinho, C.

    2000-01-01

    The objective of this paper is to present geostatistical models applied to the spatial characterisation of air pollution phenomena. A concise presentation of the geostatistical methodologies is illustrated with practical examples. The case study was conducted in an underground copper-mine located on the southern of Portugal, where a biomonitoring program using lichens has been implemented. Given the characteristics of lichens as indicators of air pollution it was possible to gather a great amount of data in space, which enabled the development and application of geostatistical methodologies. The advantages of using geostatistical models compared with deterministic models, as environmental control tools, are highlighted. (author)

  10. Vertical Descent and Landing Tests of a 0.13-Scale Model of the Convair XFY-1 Vertically Rising Airplane in Still Air, TED No. NACA DE 368

    Science.gov (United States)

    Smith, Charlee C., Jr.; Lovell, Powell M., Jr.

    1954-01-01

    An investigation is being conducted to determine the dynamic stability and control characteristics of a 0.13-scale flying model of Convair XFY-1 vertically rising airplane. This paper presents the results of flight and force tests to determine the stability and control characteristics of the model in vertical descent and landings in still air. The tests indicated that landings, including vertical descent from altitudes representing up to 400 feet for the full-scale airplane and at rates of descent up to 15 or 20 feet per second (full scale), can be performed satisfactorily. Sustained vertical descent in still air probably will be more difficult to perform because of large random trim changes that become greater as the descent velocity is increased. A slight steady head wind or cross wind might be sufficient to eliminate the random trim changes.

  11. Design Methodology - Design Synthesis

    DEFF Research Database (Denmark)

    Andreasen, Mogens Myrup

    2003-01-01

    Design Methodology is part of our practice and our knowledge about designing, and it has been strongly supported by the establishing and work of a design research community. The aim of this article is to broaden the reader¿s view of designing and Design Methodology. This is done by sketching...... the development of Design Methodology through time and sketching some important approaches and methods. The development is mainly forced by changing industrial condition, by the growth of IT support for designing, but also by the growth of insight into designing created by design researchers.......ABSTRACT Design Methodology shall be seen as our understanding of how to design; it is an early (emerging late 60ies) and original articulation of teachable and learnable methodics. The insight is based upon two sources: the nature of the designed artefacts and the nature of human designing. Today...

  12. GPS system simulation methodology

    Science.gov (United States)

    Ewing, Thomas F.

    1993-01-01

    The following topics are presented: background; Global Positioning System (GPS) methodology overview; the graphical user interface (GUI); current models; application to space nuclear power/propulsion; and interfacing requirements. The discussion is presented in vugraph form.

  13. Hazard classification methodology

    International Nuclear Information System (INIS)

    Brereton, S.J.

    1996-01-01

    This document outlines the hazard classification methodology used to determine the hazard classification of the NIF LTAB, OAB, and the support facilities on the basis of radionuclides and chemicals. The hazard classification determines the safety analysis requirements for a facility

  14. Nonlinear Image Denoising Methodologies

    National Research Council Canada - National Science Library

    Yufang, Bao

    2002-01-01

    In this thesis, we propose a theoretical as well as practical framework to combine geometric prior information to a statistical/probabilistic methodology in the investigation of a denoising problem...

  15. Clinical trial methodology

    National Research Council Canada - National Science Library

    Peace, Karl E; Chen, Ding-Geng

    2011-01-01

    "Now viewed as its own scientific discipline, clinical trial methodology encompasses the methods required for the protection of participants in a clinical trial and the methods necessary to provide...

  16. Methodology of sustainability accounting

    Directory of Open Access Journals (Sweden)

    O.H. Sokil

    2017-03-01

    Full Text Available Modern challenges of the theory and methodology of accounting are realized through the formation and implementation of new concepts, the purpose of which is to meet the needs of users in standard and unique information. The development of a methodology for sustainability accounting is a key aspect of the management of an economic entity. The purpose of the article is to form the methodological bases of accounting for sustainable development and determine its goals, objectives, object, subject, methods, functions and key aspects. The author analyzes the theoretical bases of the definition and considers the components of the traditional accounting methodology. Generalized structural diagram of the methodology for accounting for sustainable development is offered in the article. The complex of methods and principles of sustainable development accounting for systematized and non-standard provisions has been systematized. The new system of theoretical and methodological provisions of accounting for sustainable development is justified in the context of determining its purpose, objective, subject, object, methods, functions and key aspects.

  17. AES, EELS and TRIM simulation method study of InP(100 subjected to Ar+, He+ and H+ ions bombardment.

    Directory of Open Access Journals (Sweden)

    Abidri B.

    2012-06-01

    Full Text Available Auger Electron Spectroscopy (AES and Electron Energy Loss Spectroscopy (EELS have been performed in order to investigate the InP(100 surface subjected to ions bombardment. The InP(100 surface is always contaminated by carbon and oxygen revealed by C-KLL and O-KLL AES spectra recorded just after introduction of the sample in the UHV spectrometer chamber. The usually cleaning process of the surface is the bombardment by argon ions. However, even at low energy of ions beam (300 eV indium clusters and phosphorus vacancies are usually formed on the surface. The aim of our study is to compare the behaviour of the surface when submitted to He+ or H+ ions bombardment. The helium ions accelerated at 500V voltage and for 45 mn allow removing contaminants but induces damaged and no stoichiometric surface. The proton ions were accelerated at low energy of 500 eV to bombard the InP surface at room temperature. The proton ions broke the In-P chemical bonds to induce the formation of In metal islands. Such a chemical reactivity between hydrogen and phosphorus led to form chemical species such as PH and PH3, which desorbed from the surface. The chemical susceptibly and the small size of H+ advantaged their diffusion into bulk. Since the experimental methods alone were not able to give us with accuracy the disturbed depth of the target by these ions. We associate to the AES and EELS spectroscopies, the TRIM (Transport and Range of Ions in Matter simulation method in order to show the mechanism of interaction between Ar+, He+ or H+ ions and InP and determine the disturbed depth of the target by argon, helium or proton ions.

  18. Mechanisms for plasma etching of HfO{sub 2} gate stacks with Si selectivity and photoresist trimming

    Energy Technology Data Exchange (ETDEWEB)

    Shoeb, Juline; Kushner, Mark J. [Department of Electrical and Computer Engineering, Iowa State University, Ames, Iowa 50011 (United States); Department of Electrical Engineering and Computer Science, University of Michigan, Ann Arbor, Michigan 48109-2122 (United States)

    2009-11-15

    To minimize leakage currents resulting from the thinning of the insulator in the gate stack of field effect transistors, high-dielectric constant (high-k) metal oxides, and HfO{sub 2} in particular, are being implemented as a replacement for SiO{sub 2}. To speed the rate of processing, it is desirable to etch the gate stack (e.g., metal gate, antireflection layers, and dielectric) in a single process while having selectivity to the underlying Si. Plasma etching using Ar/BCl{sub 3}/Cl{sub 2} mixtures effectively etches HfO{sub 2} while having good selectivity to Si. In this article, results from integrated reactor and feature scale modeling of gate-stack etching in Ar/BCl{sub 3}/Cl{sub 2} plasmas, preceded by photoresist trimming in Ar/O{sub 2} plasmas, are discussed. It was found that BCl{sub n} species react with HfO{sub 2}, which under ion impact, form volatile etch products such as B{sub m}OCl{sub n} and HfCl{sub n}. Selectivity to Si is achieved by creating Si-B bonding as a precursor to the deposition of a BCl{sub n} polymer which slows the etch rate relative to HfO{sub 2}. The low ion energies required to achieve this selectivity then challenge one to obtain highly anisotropic profiles in the metal gate portion of the stack. Validation was performed with data from literature. The effect of bias voltage and key reactant probabilities on etch rate, selectivity, and profile are discussed.

  19. Regional Shelter Analysis Methodology

    Energy Technology Data Exchange (ETDEWEB)

    Dillon, Michael B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Dennison, Deborah [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kane, Jave [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Walker, Hoyt [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Miller, Paul [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-08-01

    The fallout from a nuclear explosion has the potential to injure or kill 100,000 or more people through exposure to external gamma (fallout) radiation. Existing buildings can reduce radiation exposure by placing material between fallout particles and exposed people. Lawrence Livermore National Laboratory was tasked with developing an operationally feasible methodology that could improve fallout casualty estimates. The methodology, called a Regional Shelter Analysis, combines the fallout protection that existing buildings provide civilian populations with the distribution of people in various locations. The Regional Shelter Analysis method allows the consideration of (a) multiple building types and locations within buildings, (b) country specific estimates, (c) population posture (e.g., unwarned vs. minimally warned), and (d) the time of day (e.g., night vs. day). The protection estimates can be combined with fallout predictions (or measurements) to (a) provide a more accurate assessment of exposure and injury and (b) evaluate the effectiveness of various casualty mitigation strategies. This report describes the Regional Shelter Analysis methodology, highlights key operational aspects (including demonstrating that the methodology is compatible with current tools), illustrates how to implement the methodology, and provides suggestions for future work.

  20. The policy trail methodology

    DEFF Research Database (Denmark)

    Holford, John; Larson, Anne; Melo, Susana

    of ‘policy trail’, arguing that it can overcome ‘methodological nationalism’ and link structure and agency in research on the ‘European educational space’. The ‘trail’ metaphor, she suggests, captures the intentionality and the erratic character of policy. The trail connects sites and brings about change......, but – although policy may be intended to be linear, with specific outcomes – policy often has to bend, and sometimes meets insurmountable obstacles. This symposium outlines and develops the methodology, but also reports on research undertaken within a major FP7 project (LLLIght’in’Europe, 2012-15) which made use......In recent years, the “policy trail” has been proposed as a methodology appropriate to the shifting and fluid governance of lifelong learning in the late modern world (Holford et al. 2013, Holford et al. 2013, Cort 2014). The contemporary environment is marked by multi-level governance (global...

  1. Changing methodologies in TESOL

    CERN Document Server

    Spiro, Jane

    2013-01-01

    Covering core topics from vocabulary and grammar to teaching, writing speaking and listening, this textbook shows you how to link research to practice in TESOL methodology. It emphasises how current understandings have impacted on the language classroom worldwide and investigates the meaning of 'methods' and 'methodology' and the importance of these for the teacher: as well as the underlying assumptions and beliefs teachers bring to bear in their practice. By introducing you to language teaching approaches, you will explore the way these are influenced by developments in our understanding of l

  2. Creativity in phenomenological methodology

    DEFF Research Database (Denmark)

    Dreyer, Pia; Martinsen, Bente; Norlyk, Annelise

    2014-01-01

    on the methodologies of van Manen, Dahlberg, Lindseth & Norberg, the aim of this paper is to argue that the increased focus on creativity and arts in research methodology is valuable to gain a deeper insight into lived experiences. We illustrate this point through examples from empirical nursing studies, and discuss......Nursing research is often concerned with lived experiences in human life using phenomenological and hermeneutic approaches. These empirical studies may use different creative expressions and art-forms to describe and enhance an embodied and personalised understanding of lived experiences. Drawing...... may support a respectful renewal of phenomenological research traditions in nursing research....

  3. A putative SUMO interacting motif in the B30.2/SPRY domain of rhesus macaque TRIM5α important for NF-κB/AP-1 signaling and HIV-1 restriction

    Directory of Open Access Journals (Sweden)

    Marie-Édith Nepveu-Traversy

    2016-01-01

    Full Text Available TRIM5α from the rhesus macaque (TRIM5αRh is a restriction factor that shows strong activity against HIV-1. TRIM5αRh binds specifically to HIV-1 capsid (CA through its B30.2/PRYSPRY domain shortly after entry of the virus into the cytoplasm. Recently, three putative SUMO interacting motifs (SIMs have been identified in the PRYSPRY domain of human and macaque TRIM5α. However, structural modeling of this domain suggested that two of them were buried in the hydrophobic core of the protein, implying that interaction with SUMO was implausible, while the third one was not relevant to restriction. In light of these results, we re-analyzed the TRIM5αRh PRYSPRY sequence and identified an additional putative SIM (435VIIC438 which we named SIM4. This motif is exposed at the surface of the PRYSPRY domain, allowing potential interactions with SUMO or SUMOylated proteins. Introducing a double mutation in SIM4 (V435K, I436K did not alter stability, unlike mutations in SIM1. SIM4-mutated TRIM5αRh failed to bind HIV-1CA and lost the ability to restrict this virus. Accordingly, SIM4 undergoes significant variation among primates and substituting this motif with naturally occurring SIM4 variants affected HIV-1 restriction by TRIM5αRh, suggesting a direct role in capsid recognition. Interestingly, SIM4-mutated TRIM5αRh also failed to activate NF-κB and AP-1-mediated transcription. Although there is no direct evidence that SIM4 is involved in direct interaction with SUMO or a SUMOylated protein, mutating this motif strongly reduced co-localization of TRIM5αRh with SUMO-1 and with PML, a SUMOylated nuclear protein. In conclusion, this new putative SIM is crucial for both direct interaction with incoming capsids and for NF-κB/AP-1 signaling. We speculate that the latter function is mediated by interactions of SIM4 with a SUMOylated protein involved in the NF-κB/AP-1 signaling pathways.

  4. Isolation and characterization of non-O157 Shiga toxin-producing Escherichia coli from beef carcasses, cuts and trimmings of abattoirs in Argentina

    Science.gov (United States)

    Brusa, Victoria; Restovich, Viviana; Galli, Lucía; Teitelbaum, David; Signorini, Marcelo; Brasesco, Hebe; Londero, Alejandra; García, Diego; Padola, Nora Lía; Superno, Valeria; Sanz, Marcelo; Petroli, Sandra; Costa, Magdalena; Bruzzone, Mariana; Sucari, Adriana; Ferreghini, Marcela; Linares, Luciano; Suberbie, Germán; Rodríguez, Ricardo

    2017-01-01

    Several foods contaminated with Shiga toxin-producing Escherichia coli (STEC) are associated with human diseases. Some countries have established microbiological criteria for non-O157 STEC, thus, the absence of serogroups O26, O45, O103, O104, O111, O121, and O145 in sprouts from the European Union or ground beef and beef trimmings from the United States is mandatory. While in Argentina screening for O26, O103, O111, O145 and O121 in ground beef, ready-to-eat food, sausages and vegetables is mandatory, other countries have zero-tolerance for all STEC in chilled beef. The aim of this study was to provide data on the prevalence of non-O157 STEC isolated from beef processed in eight Argentinean cattle slaughterhouses producing beef for export and local markets, and to know the non-O157 STEC profiles through strain characterization and genotypic analysis. Samples (n = 15,965) from 3,205 beef carcasses, 9,570 cuts and 3,190 trimmings collected between March and September 2014 were processed in pools of five samples each. Pools of samples (n = 3,193) from 641 carcasses, 1,914 cuts and 638 trimming were analyzed for non-O157 STEC isolation according to ISO/CEN 13136:2012. Of these, 37 pools of carcasses (5.8%), 111 pools of cuts (5.8%) and 45 pools of trimmings (7.0%) were positive for non-O157 STEC. STEC strains (n = 200) were isolated from 193 pools of samples. The most prevalent serotypes were O174:H21, O185:H7, O8:H19, O178:H19 and O130:H11, and the most prevalent genotypes were stx2c(vh-b) and stx2a/saa/ehxA. O103:H21 strain was eae-positive and one O178:H19 strain was aggR/aaiC-positive. The prevalence of non-O157 STEC in beef carcasses reported here was low. None of the non-O157 STEC strains isolated corresponded to the non-O157 STEC serotypes and virulence profiles isolated from human cases in Argentina in the same study period. The application of microbiological criteria for each foodstuff should be determined by risk analysis in order to have a stringent

  5. Isolation and characterization of non-O157 Shiga toxin-producing Escherichia coli from beef carcasses, cuts and trimmings of abattoirs in Argentina.

    Directory of Open Access Journals (Sweden)

    Victoria Brusa

    Full Text Available Several foods contaminated with Shiga toxin-producing Escherichia coli (STEC are associated with human diseases. Some countries have established microbiological criteria for non-O157 STEC, thus, the absence of serogroups O26, O45, O103, O104, O111, O121, and O145 in sprouts from the European Union or ground beef and beef trimmings from the United States is mandatory. While in Argentina screening for O26, O103, O111, O145 and O121 in ground beef, ready-to-eat food, sausages and vegetables is mandatory, other countries have zero-tolerance for all STEC in chilled beef. The aim of this study was to provide data on the prevalence of non-O157 STEC isolated from beef processed in eight Argentinean cattle slaughterhouses producing beef for export and local markets, and to know the non-O157 STEC profiles through strain characterization and genotypic analysis. Samples (n = 15,965 from 3,205 beef carcasses, 9,570 cuts and 3,190 trimmings collected between March and September 2014 were processed in pools of five samples each. Pools of samples (n = 3,193 from 641 carcasses, 1,914 cuts and 638 trimming were analyzed for non-O157 STEC isolation according to ISO/CEN 13136:2012. Of these, 37 pools of carcasses (5.8%, 111 pools of cuts (5.8% and 45 pools of trimmings (7.0% were positive for non-O157 STEC. STEC strains (n = 200 were isolated from 193 pools of samples. The most prevalent serotypes were O174:H21, O185:H7, O8:H19, O178:H19 and O130:H11, and the most prevalent genotypes were stx2c(vh-b and stx2a/saa/ehxA. O103:H21 strain was eae-positive and one O178:H19 strain was aggR/aaiC-positive. The prevalence of non-O157 STEC in beef carcasses reported here was low. None of the non-O157 STEC strains isolated corresponded to the non-O157 STEC serotypes and virulence profiles isolated from human cases in Argentina in the same study period. The application of microbiological criteria for each foodstuff should be determined by risk analysis in order to have a

  6. Computer Network Operations Methodology

    Science.gov (United States)

    2004-03-01

    means of their computer information systems. Disrupt - This type of attack focuses on disrupting as “attackers might surreptitiously reprogram enemy...by reprogramming the computers that control distribution within the power grid. A disruption attack introduces disorder and inhibits the effective...between commanders. The use of methodologies is widespread and done subconsciously to assist individuals in decision making. The processes that

  7. SCI Hazard Report Methodology

    Science.gov (United States)

    Mitchell, Michael S.

    2010-01-01

    This slide presentation reviews the methodology in creating a Source Control Item (SCI) Hazard Report (HR). The SCI HR provides a system safety risk assessment for the following Ares I Upper Stage Production Contract (USPC) components (1) Pyro Separation Systems (2) Main Propulsion System (3) Reaction and Roll Control Systems (4) Thrust Vector Control System and (5) Ullage Settling Motor System components.

  8. A Functional HAZOP Methodology

    DEFF Research Database (Denmark)

    Liin, Netta; Lind, Morten; Jensen, Niels

    2010-01-01

    A HAZOP methodology is presented where a functional plant model assists in a goal oriented decomposition of the plant purpose into the means of achieving the purpose. This approach leads to nodes with simple functions from which the selection of process and deviation variables follow directly...

  9. Complicating Methodological Transparency

    Science.gov (United States)

    Bridges-Rhoads, Sarah; Van Cleave, Jessica; Hughes, Hilary E.

    2016-01-01

    A historical indicator of the quality, validity, and rigor of qualitative research has been the documentation and disclosure of the behind-the-scenes work of the researcher. In this paper, we use what we call "methodological data" as a tool to complicate the possibility and desirability of such transparency. Specifically, we draw on our…

  10. Methodological Advances in Dea

    NARCIS (Netherlands)

    L. Cherchye (Laurens); G.T. Post (Thierry)

    2001-01-01

    textabstractWe survey the methodological advances in DEA over the last 25 years and discuss the necessary conditions for a sound empirical application. We hope this survey will contribute to the further dissemination of DEA, the knowledge of its relative strengths and weaknesses, and the tools

  11. NUSAM Methodology for Assessment.

    Energy Technology Data Exchange (ETDEWEB)

    Leach, Janice [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Snell, Mark K. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-07-01

    This document provides a methodology for the performance-based assessment of security systems designed for the protection of nuclear and radiological materials and the processes that produce and/or involve them. It is intended for use with both relatively simple installations and with highly regulated complex sites with demanding security requirements.

  12. MIRD methodology. Part 1

    International Nuclear Information System (INIS)

    Rojo, Ana M.

    2004-01-01

    This lecture develops the MIRD (Medical Internal Radiation Dose) methodology for the evaluation of the internal dose due to the administration of radiopharmaceuticals. In this first part, the basic concepts and the main equations are presented. The ICRP Dosimetric System is also explained. (author)

  13. Response Surface Methodology

    NARCIS (Netherlands)

    Kleijnen, Jack P.C.

    2014-01-01

    Abstract: This chapter first summarizes Response Surface Methodology (RSM), which started with Box and Wilson’s article in 1951 on RSM for real, non-simulated systems. RSM is a stepwise heuristic that uses first-order polynomials to approximate the response surface locally. An estimated polynomial

  14. MIRD methodology. Part 2

    International Nuclear Information System (INIS)

    Gomez Parada, Ines

    2004-01-01

    This paper develops the MIRD (Medical Internal Radiation Dose) methodology for the evaluation of the internal dose due to the administration of radiopharmaceuticals. In this second part, different methods for the calculation of the accumulated activity are presented, together with the effective half life definition. Different forms of Retention Activity curves are also shown. (author)

  15. TRIM28 and β-actin identified via nanobody-based reverse proteomics approach as possible human glioblastoma biomarkers.

    Directory of Open Access Journals (Sweden)

    Ivana Jovčevska

    spectrometry analysis revealed two proteins, TRIM28 and β-actin, that were up-regulated in the GBM stem-like cells compared to the controls.

  16. TRIM28 and β-actin identified via nanobody-based reverse proteomics approach as possible human glioblastoma biomarkers.

    Science.gov (United States)

    Jovčevska, Ivana; Zupanec, Neja; Kočevar, Nina; Cesselli, Daniela; Podergajs, Neža; Stokin, Clara Limbaeck; Myers, Michael P; Muyldermans, Serge; Ghassabeh, Gholamreza Hassanzadeh; Motaln, Helena; Ruaro, Maria Elisabetta; Bourkoula, Evgenia; Turnšek, Tamara Lah; Komel, Radovan

    2014-01-01

    analysis revealed two proteins, TRIM28 and β-actin, that were up-regulated in the GBM stem-like cells compared to the controls.

  17. Air pollution

    OpenAIRE

    MacKenbach, JP; Henschel, S; Goodman, P; McKee, M

    2013-01-01

    The human costs of air pollution are considerable in Jordan. According to a report published in 2000 by the World Bank under the Mediterranean Environmental Technical Assistance Program (METAP), approximately 600 people die prematurely each year in Jordan because of urban pollution. 50-90% of air pollution in Jordanian towns is caused by road traffic. Readings taken in 2007 by Jordanian researchers showed that levels of black carbon particles in the air were higher in urban areas (caused by v...

  18. Methodological study of air quality using lichens as ecological bio-indicators, chemical element bio-accumulators and oxidative stress bio-markers; Etude methodologique de la qualite de l'air en Lorraine-Nord par les lichens: contribution en tant que bioindicateurs ecologiques, bioaccumulateurs d'elements chimiques et biomarqueurs du stress oxydant

    Energy Technology Data Exchange (ETDEWEB)

    Signoret, J.

    2002-11-15

    The objective of this thesis was to contribute to a better understanding of the impact of the atmospheric pollutions on lichens in experimental conditions of field (Lorraine region, France). Techniques of sampling areas analysis for epiphytic lichens were little developed in bio-indication. Without a precise method and a solid validation of the choices of the surface of sampling, survey analysis continue to be subjective and comparative studies and hypotheses testing are rough. To examine this problem, we tested an operational technique of sampling and spatial analysis, based on digitized and geo-referenced data, which makes more objective the lichen covering and frequency assessment. We present a simple example to demonstrate how our investigations will allow to do the link between survey and air quality diagnosis, with perspectives on i) stratified random sampling techniques of lichen communities based on the image interpretation, ii) multi-scale sampling techniques to estimate the efficiency of the sampling grid classically used in bio-monitoring and iii) GIS (Geographical Information Systems) and geostatistical techniques to study floristic and ecological variations at every sampling point. The transplantation is a field technique used for the study air pollution effects and chemical elements accumulation on the lichen symbiosis. Precipitation is known to play an important role in the uptake and release of chemical elements by lichen thalli, but few information was available on their roles in the lichen resistance exposed to photo-oxidizing pollutants. We used this technique to study the effects of gas pollutants and airborne chemical elements on the lichen physiology exposed or not at precipitation. To analyze these interactions, the lichen Hypogymnia physodes (L.) Nyl. was transplanted to 5 locations of the Moselle valley with different levels of air pollution for 14, 34 and 68 days (summer 2001). In each of these sites, 6 transplantation designs, covered or

  19. Boundary-Object Trimming

    DEFF Research Database (Denmark)

    Bossen, Claus; Jensen, Lotte Groth; Udsen, Flemming Witt

    2014-01-01

    implementation, which also coupled the work of medical secretaries more tightly to that of other staff, and led to task drift among professions. Medical secretaries have been relatively invisible to health informatics and CSCW, and we propose the term ‘boundary-object trimming’ to foreground and conceptualize...

  20. Warping for trim statics

    KAUST Repository

    Zhang, Dongliang

    2014-08-05

    The quality of migration images depends on the accuracy of the velocity model. For large velocity errors, the migration image is strongly distorted, which unflattens events in the common image gathers and consequently leads to a blurring in the stacked migration image. To mitigate this problem, we propose dynamic image warping to flatten the common image gathers before stacking and to enhance the signal-to-noise ratio of the migration image. Numerical tests on the Marmousi model and GOM data show that image warping of the prestack images followed by stacking leads to much better resolved reflectors than the original migration image. The problem, however, is that the reflector locations have increased uncertainty because the wrong velocity model is still used.

  1. Warping for trim statics

    KAUST Repository

    Zhang, Dongliang; Wang, Xin; Huang, Yunsong; Schuster, Gerard T.

    2014-01-01

    The quality of migration images depends on the accuracy of the velocity model. For large velocity errors, the migration image is strongly distorted, which unflattens events in the common image gathers and consequently leads to a blurring in the stacked migration image. To mitigate this problem, we propose dynamic image warping to flatten the common image gathers before stacking and to enhance the signal-to-noise ratio of the migration image. Numerical tests on the Marmousi model and GOM data show that image warping of the prestack images followed by stacking leads to much better resolved reflectors than the original migration image. The problem, however, is that the reflector locations have increased uncertainty because the wrong velocity model is still used.

  2. Trimming proline dehydrogenase

    NARCIS (Netherlands)

    Huijbers, Mieke M.E.

    2017-01-01

    Proline is one of the proteinogenic amino acids and one of the most abundant amino acids in the cell. Next to serving as one of the non-essential amino acids, proline also has a central role in metabolism. In Chapter 1, the different functions of this imino acid are described, as

  3. Disruption of the ASTN2 / TRIM32 locus at 9q33.1 is a risk factor in males for Autism Spectrum Disorders, ADHD and other neurodevelopmental phenotypes

    DEFF Research Database (Denmark)

    Lionel, Anath C; Tammimies, Kristiina; Vaags, Andrea K

    2014-01-01

    Rare copy number variants (CNVs) disrupting ASTN2 or both ASTN2 and TRIM32 have been reported at 9q33.1 by genome-wide studies in a few individuals with neurodevelopmental disorders. The vertebrate-specific astrotactins, ASTN2 and its paralog ASTN1, have key roles in glial-guided neuronal migration...... during brain development. To determine the prevalence of astrotactin mutations and delineate their associated phenotypic spectrum, we screened ASTN2/TRIM32 and ASTN1 (1q25.2) for exonic CNVs in clinical microarray data from 89,985 individuals across 10 sites, including 64,114 neurodevelopmental disorder...... subjects. In this clinical dataset, we identified 46 deletions and 12 duplications affecting ASTN2. Deletions of ASTN1 were much rarer. Deletions near the 3' terminus of ASTN2, which would disrupt all transcript isoforms (a subset of these deletions also included TRIM32), were significantly enriched...

  4. Soft Systems Methodology

    Science.gov (United States)

    Checkland, Peter; Poulter, John

    Soft systems methodology (SSM) is an approach for tackling problematical, messy situations of all kinds. It is an action-oriented process of inquiry into problematic situations in which users learn their way from finding out about the situation, to taking action to improve it. The learning emerges via an organised process in which the situation is explored using a set of models of purposeful action (each built to encapsulate a single worldview) as intellectual devices, or tools, to inform and structure discussion about a situation and how it might be improved. This paper, written by the original developer Peter Checkland and practitioner John Poulter, gives a clear and concise account of the approach that covers SSM's specific techniques, the learning cycle process of the methodology and the craft skills which practitioners develop. This concise but theoretically robust account nevertheless includes the fundamental concepts, techniques, core tenets described through a wide range of settings.

  5. Transparent Guideline Methodology Needed

    DEFF Research Database (Denmark)

    Lidal, Ingeborg; Norén, Camilla; Mäkelä, Marjukka

    2013-01-01

    As part of learning at the Nordic Workshop of Evidence-based Medicine, we have read with interest the practice guidelines for central venous access, published in your Journal in 2012.1 We appraised the quality of this guideline using the checklist developed by The Evidence-Based Medicine Working ...... are based on best currently available evidence. Our concerns are in two main categories: the rigor of development, including methodology of searching, evaluating, and combining the evidence; and editorial independence, including funding and possible conflicts of interest....... Group.2 Similar criteria for guideline quality have been suggested elsewhere.3 Our conclusion was that this much needed guideline is currently unclear about several aspects of the methodology used in developing the recommendations. This means potential users cannot be certain that the recommendations...

  6. Web survey methodology

    CERN Document Server

    Callegaro, Mario; Vehovar, Asja

    2015-01-01

    Web Survey Methodology guides the reader through the past fifteen years of research in web survey methodology. It both provides practical guidance on the latest techniques for collecting valid and reliable data and offers a comprehensive overview of research issues. Core topics from preparation to questionnaire design, recruitment testing to analysis and survey software are all covered in a systematic and insightful way. The reader will be exposed to key concepts and key findings in the literature, covering measurement, non-response, adjustments, paradata, and cost issues. The book also discusses the hottest research topics in survey research today, such as internet panels, virtual interviewing, mobile surveys and the integration with passive measurements, e-social sciences, mixed modes and business intelligence. The book is intended for students, practitioners, and researchers in fields such as survey and market research, psychological research, official statistics and customer satisfaction research.

  7. Air lock

    International Nuclear Information System (INIS)

    Palkovich, P.; Gruber, J.; Madlener, W.

    1974-01-01

    The patent refers to an air lock system preferably for nuclear stations for the transport of heavy loads by means of a trolley on rails. For opening and closing of the air lock parts of the rails are removed, e.g. by a second rail system perpendicular to the main rails. (P.K.)

  8. Steganography: LSB Methodology

    Science.gov (United States)

    2012-08-02

    of LSB steganography in grayscale and color images . In J. Dittmann, K. Nahrstedt, and P. Wohlmacher, editors, Proceedings of the ACM, Special...Fridrich, M. Gojan and R. Du paper titled “Reliable detection of LSB steganography in grayscale and color images ”. From a general perspective Figure 2...REPORT Steganography : LSB Methodology (Progress Report) 14. ABSTRACT 16. SECURITY CLASSIFICATION OF: In computer science, steganography is the science

  9. Generation of a human immunodeficiency virus type 1 chronically infected monkey B cell line expressing low levels of endogenous TRIM5alpha.

    Science.gov (United States)

    Ridolfi, Barbara; Catone, Stefania; Sgarbanti, Marco; Sernicola, Leonardo; Battistini, Angela; Parolin, Cristina; Titti, Fausto; Borsetti, Alessandra

    2009-12-01

    Several innate cellular antiviral factors exist in mammalian cells that prevent the replication of retroviruses. Among them, the tripartite motif protein (TRIM)5alpha has been shown to block human immunodeficiency virus type 1 (HIV-1) infection in several types of Old World monkey cells. Here we report a novel HIV-1 chronically infected monkey B cell line, F6/HIV-1, characterized by very low levels of TRIM5alpha expression that allows HIV-1 to overcome the restriction. Virus produced by F6/HIV-1 cells fails to infect monkey cells but retains the ability to infect human peripheral blood mononuclear cells (PBMCs) and T cell lines, although with a reduced infectivity compared to the input virus. Ultrastructural analyses revealed the presence of budding virions at the F6/HIV-1 cells plasma membrane characterized by a typical conical core shell. To our knowledge F6/HIV-1 is the first monkey cell line chronically infected by HIV-1 and able to release infectious particles thus representing a useful tool to gain further insights into the molecular mechanisms of HIV-1 pathogenesis.

  10. Transcriptional activator TAp63 is upregulated in muscular atrophy during ALS and induces the pro-atrophic ubiquitin ligase Trim63

    Science.gov (United States)

    von Grabowiecki, Yannick; Abreu, Paula; Blanchard, Orphee; Palamiuc, Lavinia; Benosman, Samir; Mériaux, Sophie; Devignot, Véronique; Gross, Isabelle; Mellitzer, Georg; Gonzalez de Aguilar, José L; Gaiddon, Christian

    2016-01-01

    Mechanisms of muscle atrophy are complex and their understanding might help finding therapeutic solutions for pathologies such as amyotrophic lateral sclerosis (ALS). We meta-analyzed transcriptomic experiments of muscles of ALS patients and mouse models, uncovering a p53 deregulation as common denominator. We then characterized the induction of several p53 family members (p53, p63, p73) and a correlation between the levels of p53 family target genes and the severity of muscle atrophy in ALS patients and mice. In particular, we observed increased p63 protein levels in the fibers of atrophic muscles via denervation-dependent and -independent mechanisms. At a functional level, we demonstrated that TAp63 and p53 transactivate the promoter and increased the expression of Trim63 (MuRF1), an effector of muscle atrophy. Altogether, these results suggest a novel function for p63 as a contributor to muscular atrophic processes via the regulation of multiple genes, including the muscle atrophy gene Trim63. DOI: http://dx.doi.org/10.7554/eLife.10528.001 PMID:26919175

  11. Soil Radiological Characterisation Methodology

    International Nuclear Information System (INIS)

    Attiogbe, Julien; Aubonnet, Emilie; De Maquille, Laurence; De Moura, Patrick; Desnoyers, Yvon; Dubot, Didier; Feret, Bruno; Fichet, Pascal; Granier, Guy; Iooss, Bertrand; Nokhamzon, Jean-Guy; Ollivier Dehaye, Catherine; Pillette-Cousin, Lucien; Savary, Alain

    2014-12-01

    This report presents the general methodology and best practice approaches which combine proven existing techniques for sampling and characterisation to assess the contamination of soils prior to remediation. It is based on feedback of projects conducted by main French nuclear stakeholders involved in the field of remediation and dismantling (EDF, CEA, AREVA and IRSN). The application of this methodology will enable the project managers to obtain the elements necessary for the drawing up of files associated with remediation operations, as required by the regulatory authorities. It is applicable to each of the steps necessary for the piloting of remediation work-sites, depending on the objectives targeted (release into the public domain, re-use, etc.). The main part describes the applied statistical methodology with the exploratory analysis and variogram data, identification of singular points and their location. The results obtained permit assessment of a mapping to identify the contaminated surface and subsurface areas. It stakes the way for radiological site characterisation since the initial investigations from historical and functional analysis to check that the remediation objectives have been met. It follows an example application from the feedback of the remediation of a contaminated site on the Fontenay aux Roses facility. It is supplemented by a glossary of main terms used in the field from different publications or international standards. This technical report is a support of the ISO Standard ISO ISO/TC 85/SC 5 N 18557 'Sampling and characterisation principles for soils, buildings and infrastructures contaminated by radionuclides for remediation purposes'. (authors) [fr

  12. Laser scattering methodology for measuring particulates in the air

    Directory of Open Access Journals (Sweden)

    Carlo Giglioni

    2009-03-01

    Full Text Available A description is given of the laser scattering method to measure PM10, PM2.5 and PM1 dusts in confirmed environments (museums, libraries, archives, art galleries, etc.. Such equipment presents many advantages, in comparison with those which are actually in use, not only from an analytic but also from a functional point of view.

  13. Top Level Space Cost Methodology (TLSCM)

    Science.gov (United States)

    1997-12-02

    Software 7 6. ACEIT . 7 C. Ground Rules and Assumptions 7 D. Typical Life Cycle Cost Distribution 7 E. Methodologies 7 1. Cost/budget Threshold 9 2. Analogy...which is based on real-time Air Force and space programs. Ref.(25:2- 8, 2-9) 6. ACEIT : Automated Cost Estimating Integrated Tools( ACEIT ), Tecolote...Research, Inc. There is a way to use the ACEIT cost program to get a print-out of an expanded WBS. Therefore, find someone that has ACEIT experience and

  14. Methodology applied to develop the DHIE: applied methodology

    CSIR Research Space (South Africa)

    Herselman, Marlien

    2016-12-01

    Full Text Available This section will address the methodology that was applied to develop the South African Digital Health Innovation Ecosystem (DHIE). Each chapter under Section B represents a specific phase in the methodology....

  15. Air pollution

    Energy Technology Data Exchange (ETDEWEB)

    Strauss, W; Mainwaring, S J

    1984-01-01

    This book deals with the nature of air pollution. The numerous sources of unwanted gases and dust particles in the air are discussed. Details are presented of the effects of pollutants on man, animals, vegetation and on inanimate materials. Methods used to measure, monitor and control air pollution are presented. The authors include information on the socio-economic factors which impinge on pollution control and on the problems the future will bring as methods of generating energy change and industries provide new sources of pollutants.

  16. Case Study Research Methodology

    Directory of Open Access Journals (Sweden)

    Mark Widdowson

    2011-01-01

    Full Text Available Commenting on the lack of case studies published in modern psychotherapy publications, the author reviews the strengths of case study methodology and responds to common criticisms, before providing a summary of types of case studies including clinical, experimental and naturalistic. Suggestions are included for developing systematic case studies and brief descriptions are given of a range of research resources relating to outcome and process measures. Examples of a pragmatic case study design and a hermeneutic single-case efficacy design are given and the paper concludes with some ethical considerations and an exhortation to the TA community to engage more widely in case study research.

  17. Sample size methodology

    CERN Document Server

    Desu, M M

    2012-01-01

    One of the most important problems in designing an experiment or a survey is sample size determination and this book presents the currently available methodology. It includes both random sampling from standard probability distributions and from finite populations. Also discussed is sample size determination for estimating parameters in a Bayesian setting by considering the posterior distribution of the parameter and specifying the necessary requirements. The determination of the sample size is considered for ranking and selection problems as well as for the design of clinical trials. Appropria

  18. Geotechnical site assessment methodology

    International Nuclear Information System (INIS)

    Tunbridge, L.W.; Richards, L.R.

    1985-09-01

    The reports comprising this volume concern the research conducted on geotechnical site assessment methodology at the Carwynnen test mine in granites in Cornwall, with particular reference to the effect of structures imposed by discontinuities on the engineering behaviour of rock masses. The topics covered are: in-situ stress measurements using (a) the hydraulic fracturing method, or (b) the US Bureau of Mines deformation probe; scanline discontinuity survey - coding form and instructions, and data; applicability of geostatistical estimation methods to scalar rock properties; comments on in-situ stress at the Carwynnen test mine and the state of stress in the British Isles. (U.K.)

  19. Microphysics evolution and methodology

    International Nuclear Information System (INIS)

    Dionisio, J.S.

    1990-01-01

    A few general features of microscopics evolution and their relationship with microscopics methodology are briefly surveyed. Several pluri-disciplinary and interdisciplinary aspects of microscopics research are also discussed in the present scientific context. The need for an equilibrium between individual tendencies and collective constraints required by team work, already formulated thirty years ago by Frederic Joliot, is particularly stressed in the present conjuncture of Nuclear Research favouring very large team projects and discouraging individual initiatives. The increasing importance of the science of science (due to their multiple social, economical, ecological aspects) and the stronger competition between national and international tendencies of scientific (and technical) cooperation are also discussed. (author)

  20. MIRD methodology; Metodologia MIRD

    Energy Technology Data Exchange (ETDEWEB)

    Rojo, Ana M [Autoridad Regulatoria Nuclear, Buenos Aires (Argentina); Gomez Parada, Ines [Sociedad Argentina de Radioproteccion, Buenos Aires (Argentina)

    2004-07-01

    The MIRD (Medical Internal Radiation Dose) system was established by the Society of Nuclear Medicine of USA in 1960 to assist the medical community in the estimation of the dose in organs and tissues due to the incorporation of radioactive materials. Since then, 'MIRD Dose Estimate Report' (from the 1 to 12) and 'Pamphlets', of great utility for the dose calculations, were published. The MIRD system was planned essentially for the calculation of doses received by the patients during nuclear medicine diagnostic procedures. The MIRD methodology for the absorbed doses calculations in different tissues is explained.

  1. Beam optimization: improving methodology

    International Nuclear Information System (INIS)

    Quinteiro, Guillermo F.

    2004-01-01

    Different optimization techniques commonly used in biology and food technology allow a systematic and complete analysis of response functions. In spite of the great interest in medical and nuclear physics in the problem of optimizing mixed beams, little attention has been given to sophisticate mathematical tools. Indeed, many techniques are perfectly suited to the typical problem of beam optimization. This article is intended as a guide to the use of two methods, namely Response Surface Methodology and Simplex, that are expected to fasten the optimization process and, meanwhile give more insight into the relationships among the dependent variables controlling the response

  2. Literacy research methodologies

    CERN Document Server

    Duke, Nell K

    2012-01-01

    The definitive reference on literacy research methods, this book serves as a key resource for researchers and as a text in graduate-level courses. Distinguished scholars clearly describe established and emerging methodologies, discuss the types of questions and claims for which each is best suited, identify standards of quality, and present exemplary studies that illustrate the approaches at their best. The book demonstrates how each mode of inquiry can yield unique insights into literacy learning and teaching and how the methods can work together to move the field forward.   New to This Editi

  3. Methodology of site studies

    International Nuclear Information System (INIS)

    Caries, J.C.; Hugon, J.; Grauby, A.

    1980-01-01

    This methodology consists in an essentially dynamic, estimated and follow-up analysis of the impact of discharges on all the environment compartments, whether natural or not, that play a part in the protection of man and his environment. It applies at two levels, to wit: the choice of site, or the detailed study of the site selected. Two examples of its application will be developed, namely: at the choice of site level in the case of marine sites, and of the detailed study level of the chosen site in that of a riverside site [fr

  4. Alternative pricing methodologies

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    With the increased interest in competitive market forces and growing recognition of the deficiencies in current practices, FERC and others are exploring alternatives to embedded cost pricing. A number of these alternatives are discussed in this chapter. Marketplace pricing, discussed briefly here, is the subject of the next chapter. Obviously, the pricing formula may combine several of these methodologies. One utility of which the authors are aware is seeking a price equal to the sum of embedded costs, opportunity costs, line losses, value of service, FERC's percentage adder formula and a contract service charge

  5. Air lasing

    CERN Document Server

    Cheng, Ya

    2018-01-01

    This book presents the first comprehensive, interdisciplinary review of the rapidly developing field of air lasing. In most applications of lasers, such as cutting and engraving, the laser source is brought to the point of service where the laser beam is needed to perform its function. However, in some important applications such as remote atmospheric sensing, placing the laser at a convenient location is not an option. Current sensing schemes rely on the detection of weak backscattering of ground-based, forward-propagating optical probes, and possess limited sensitivity. The concept of air lasing (or atmospheric lasing) relies on the idea that the constituents of the air itself can be used as an active laser medium, creating a backward-propagating, impulsive, laser-like radiation emanating from a remote location in the atmosphere. This book provides important insights into the current state of development of air lasing and its applications.

  6. Mass concentrations of BTEX inside air environment of buses in Changsha, China

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Xiaokai; Zhang, Guoqiang; Zhang, Quan [College of Civil Engineering, Hunan University, Changsha 410082, Hunan (China); Chen, Hong [College of Environmental Science and Engineering, Hunan University, Changsha 410082, Hunan (China)

    2011-02-15

    In order to estimate the mass concentrations of benzene (B), toluene (T), ethylbenzene (E) and xylenes (X) inside air environment of buses and to analyze the influencing factors of the BTEX pollution levels, 22 public buses were investigated in Changsha, China. The interior air was collected through activated charcoal adsorption tubes and then the air samples were analyzed with thermally desorbed gas chromatograph. The mass concentrations ranged from 21.3 to 106.4 {mu}g/m{sup 3} for benzene, from 53.5 to 266.0 {mu}g/m{sup 3} for toluene, from 19.6 to 95.9 {mu}g/m{sup 3} for ethylbenzene and from 46.9 to 234.8 {mu}g/m{sup 3} for xylenes. Their mean values were 68.7, 179.7, 62.5 and 151.8 {mu}g/m{sup 3}, respectively. The rates of buses tested where the interior concentrations exceeded the limit levels of Chinese Indoor Air Quality Standard were 45.5% for toluene and 13.6% for xylenes. The BTEX levels increased when in-car temperature or relative humidity rose, and decreased when car age or travel distance increased. The BTEX concentrations were higher in leather trims buses than in non-leather trims ones, in air-conditioned buses than in non-air-conditioned ones, and in high-grade buses than in low-grade ones. According to the analysis of multiple linear regression equation, car age and in-car temperature were two most important factors influencing the BTEX pollution levels in the cabins of public buses. (author)

  7. Air Warfare

    Science.gov (United States)

    2002-03-01

    genus as its predecessor of pre-war days. It would, however, be erroneous to conclude from this that the military value of each new development was...the paucity of communications, its conduct, when acting alone, has of necessity to be somewhat stereotyped in nature, and to con- form to a pre...the air, the attack commander, provided his command be equipped with defensive air power, has a rôle to perform which is simple and stereotyped in

  8. LOFT uncertainty-analysis methodology

    International Nuclear Information System (INIS)

    Lassahn, G.D.

    1983-01-01

    The methodology used for uncertainty analyses of measurements in the Loss-of-Fluid Test (LOFT) nuclear-reactor-safety research program is described and compared with other methodologies established for performing uncertainty analyses

  9. LOFT uncertainty-analysis methodology

    International Nuclear Information System (INIS)

    Lassahn, G.D.

    1983-01-01

    The methodology used for uncertainty analyses of measurements in the Loss-of-Fluid Test (LOFT) nuclear reactor safety research program is described and compared with other methodologies established for performing uncertainty analyses

  10. Agent-based Modeling Methodology for Analyzing Weapons Systems

    Science.gov (United States)

    2015-03-26

    technique involve model structure, system representation and the degree of validity, coupled with the simplicity, of the overall model. ABM is best suited... system representation of the air combat system . We feel that a simulation model that combines ABM with equation-based representation of weapons and...AGENT-BASED MODELING METHODOLOGY FOR ANALYZING WEAPONS SYSTEMS THESIS Casey D. Connors, Major, USA

  11. Methodology, Algorithms, and Emerging Tool for Automated Design of Intelligent Integrated Multi-Sensor Systems

    Directory of Open Access Journals (Sweden)

    Andreas König

    2009-11-01

    Full Text Available The emergence of novel sensing elements, computing nodes, wireless communication and integration technology provides unprecedented possibilities for the design and application of intelligent systems. Each new application system must be designed from scratch, employing sophisticated methods ranging from conventional signal processing to computational intelligence. Currently, a significant part of this overall algorithmic chain of the computational system model still has to be assembled manually by experienced designers in a time and labor consuming process. In this research work, this challenge is picked up and a methodology and algorithms for automated design of intelligent integrated and resource-aware multi-sensor systems employing multi-objective evolutionary computation are introduced. The proposed methodology tackles the challenge of rapid-prototyping of such systems under realization constraints and, additionally, includes features of system instance specific self-correction for sustained operation of a large volume and in a dynamically changing environment. The extension of these concepts to the reconfigurable hardware platform renders so called self-x sensor systems, which stands, e.g., for self-monitoring, -calibrating, -trimming, and -repairing/-healing systems. Selected experimental results prove the applicability and effectiveness of our proposed methodology and emerging tool. By our approach, competitive results were achieved with regard to classification accuracy, flexibility, and design speed under additional design constraints.

  12. RHIC Data Correlation Methodology

    International Nuclear Information System (INIS)

    Michnoff, R.; D'Ottavio, T.; Hoff, L.; MacKay, W.; Satogata, T.

    1999-01-01

    A requirement for RHIC data plotting software and physics analysis is the correlation of data from all accelerator data gathering systems. Data correlation provides the capability for a user to request a plot of multiple data channels vs. time, and to make meaningful time-correlated data comparisons. The task of data correlation for RHIC requires careful consideration because data acquisition triggers are generated from various asynchronous sources including events from the RHIC Event Link, events from the two Beam Sync Links, and other unrelated clocks. In order to correlate data from asynchronous acquisition systems a common time reference is required. The RHIC data correlation methodology will allow all RHIC data to be converted to a common wall clock time, while still preserving native acquisition trigger information. A data correlation task force team, composed of the authors of this paper, has been formed to develop data correlation design details and provide guidelines for software developers. The overall data correlation methodology will be presented in this paper

  13. SMART performance analysis methodology

    International Nuclear Information System (INIS)

    Lim, H. S.; Kim, H. C.; Lee, D. J.

    2001-04-01

    To ensure the required and desired operation over the plant lifetime, the performance analysis for the SMART NSSS design is done by means of the specified analysis methodologies for the performance related design basis events(PRDBE). The PRDBE is an occurrence(event) that shall be accommodated in the design of the plant and whose consequence would be no more severe than normal service effects of the plant equipment. The performance analysis methodology which systematizes the methods and procedures to analyze the PRDBEs is as follows. Based on the operation mode suitable to the characteristics of the SMART NSSS, the corresponding PRDBEs and allowable range of process parameters for these events are deduced. With the developed control logic for each operation mode, the system thermalhydraulics are analyzed for the chosen PRDBEs using the system analysis code. Particularly, because of different system characteristics of SMART from the existing commercial nuclear power plants, the operation mode, PRDBEs, control logic, and analysis code should be consistent with the SMART design. This report presents the categories of the PRDBEs chosen based on each operation mode and the transition among these and the acceptance criteria for each PRDBE. It also includes the analysis methods and procedures for each PRDBE and the concept of the control logic for each operation mode. Therefore this report in which the overall details for SMART performance analysis are specified based on the current SMART design, would be utilized as a guide for the detailed performance analysis

  14. Relative Hazard Calculation Methodology

    International Nuclear Information System (INIS)

    DL Strenge; MK White; RD Stenner; WB Andrews

    1999-01-01

    The methodology presented in this document was developed to provide a means of calculating the RH ratios to use in developing useful graphic illustrations. The RH equation, as presented in this methodology, is primarily a collection of key factors relevant to understanding the hazards and risks associated with projected risk management activities. The RH equation has the potential for much broader application than generating risk profiles. For example, it can be used to compare one risk management activity with another, instead of just comparing it to a fixed baseline as was done for the risk profiles. If the appropriate source term data are available, it could be used in its non-ratio form to estimate absolute values of the associated hazards. These estimated values of hazard could then be examined to help understand which risk management activities are addressing the higher hazard conditions at a site. Graphics could be generated from these absolute hazard values to compare high-hazard conditions. If the RH equation is used in this manner, care must be taken to specifically define and qualify the estimated absolute hazard values (e.g., identify which factors were considered and which ones tended to drive the hazard estimation)

  15. Insights into PRA methodologies

    International Nuclear Information System (INIS)

    Gallagher, D.; Lofgren, E.; Atefi, B.; Liner, R.; Blond, R.; Amico, P.

    1984-08-01

    Probabilistic Risk Assessments (PRAs) for six nuclear power plants were examined to gain insight into how the choice of analytical methods can affect the results of PRAs. The PRA sreflectope considered was limited to internally initiated accidents sequences through core melt. For twenty methodological topic areas, a baseline or minimal methodology was specified. The choice of methods for each topic in the six PRAs was characterized in terms of the incremental level of effort above the baseline. A higher level of effort generally reflects a higher level of detail or a higher degree of sophistication in the analytical approach to a particular topic area. The impact on results was measured in terms of how additional effort beyond the baseline level changed the relative importance and ordering of dominant accident sequences compared to what would have been observed had methods corresponding to the baseline level of effort been employed. This measure of impact is a more useful indicator of how methods affect perceptions of plant vulnerabilities than changes in core melt frequency would be. However, the change in core melt frequency was used as a secondary measure of impact for nine topics where availability of information permitted. Results are presented primarily in the form of effort-impact matrices for each of the twenty topic areas. A suggested effort-impact profile for future PRAs is presented

  16. Air conditioner

    International Nuclear Information System (INIS)

    Sato, Masaaki

    1993-01-01

    The present invention provides an air conditioner which can prevent an undesirable effects on a human body due to radon daughter nuclides in a closed space. That is, the concentration of the radon daughter nuclides in the air in the closed space is continuously measured. A necessary amount of ventilation air is determined based on the measured concentration to generate control signals. External air is introduced into the closed space by the generated control signals. With such procedures, necessary amount of external air is taken from the atmospheric air which can be regarded to have the radon daughter nuclide concentration substantially at zero, thereby enabling to reduce the concentration of the radon daughter nuclides in the closed space. As a result, undesired effects on the human body due to the radon daughter nuclides staying in the closed space can be prevented. According to simulation, the radon daughter nuclides are rapidly decreased only by ventilation only for three times or so in one hour. Accordingly, ventilation is extremely effective and convenient means as a countermeasure for the radon daughter nuclides. (I.S.)

  17. Scrum methodology in banking environment

    OpenAIRE

    Strihová, Barbora

    2015-01-01

    Bachelor thesis "Scrum methodology in banking environment" is focused on one of agile methodologies called Scrum and description of the methodology used in banking environment. Its main goal is to introduce the Scrum methodology and outline a real project placed in a bank focused on software development through a case study, address problems of the project, propose solutions of the addressed problems and identify anomalies of Scrum in software development constrained by the banking environmen...

  18. Experimental Economics: Some Methodological Notes

    OpenAIRE

    Fiore, Annamaria

    2009-01-01

    The aim of this work is presenting in a self-contained paper some methodological aspects as they are received in the current experimental literature. The purpose has been to make a critical review of some very influential papers dealing with methodological issues. In other words, the idea is to have a single paper where people first approaching experimental economics can find summarised (some) of the most important methodological issues. In particular, the focus is on some methodological prac...

  19. A changing climate: impacts on human exposures to O3 using an integrated modeling methodology

    Science.gov (United States)

    Predicting the impacts of changing climate on human exposure to air pollution requires future scenarios that account for changes in ambient pollutant concentrations, population sizes and distributions, and housing stocks. An integrated methodology to model changes in human exposu...

  20. Simulation and Optimization Methodologies for Military Transportation Network Routing and Scheduling and for Military Medical Services

    National Research Council Canada - National Science Library

    Rodin, Ervin Y

    2005-01-01

    The purpose of this present research was to develop a generic model and methodology for analyzing and optimizing large-scale air transportation networks including both their routing and their scheduling...

  1. Geotechnical site assessment methodology

    International Nuclear Information System (INIS)

    Tunbridge, L.W.; Richards, L.R.

    1985-09-01

    A final report summarizing the research conducted on geotechnical site assessment methodology at the Carwynnen test mine in Cornwall. The geological setting of the test site in the Cornubian granite batholith is described. The effect of structure imposed by discontinuities on the engineering behaviour of rock masses is discussed and the scanline survey method of obtaining data on discontinuities in the rock mass is described. The applicability of some methods of statistical analysis for discontinuity data is reviewed. The requirement for remote geophysical methods of characterizing the mass is discussed and experiments using seismic and ultrasonic velocity measurements are reported. Methods of determining the in-situ stresses are described and the final results of a programme of in-situ stress measurements using the overcoring and hydrofracture methods are reported. (author)

  2. UNCOMMON SENSORY METHODOLOGIES

    Directory of Open Access Journals (Sweden)

    Vladimír Vietoris

    2015-02-01

    Full Text Available Sensory science is the young but the rapidly developing field of the food industry. Actually, the great emphasis is given to the production of rapid techniques of data collection, the difference between consumers and trained panel is obscured and the role of sensory methodologists is to prepare the ways for evaluation, by which a lay panel (consumers can achieve identical results as a trained panel. Currently, there are several conventional methods of sensory evaluation of food (ISO standards, but more sensory laboratories are developing methodologies that are not strict enough in the selection of evaluators, their mechanism is easily understandable and the results are easily interpretable. This paper deals with mapping of marginal methods used in sensory evaluation of food (new types of profiles, CATA, TDS, napping.

  3. Safety class methodology

    International Nuclear Information System (INIS)

    Donner, E.B.; Low, J.M.; Lux, C.R.

    1992-01-01

    DOE Order 6430.1A, General Design Criteria (GDC), requires that DOE facilities be evaluated with respect to ''safety class items.'' Although the GDC defines safety class items, it does not provide a methodology for selecting safety class items. The methodology described in this paper was developed to assure that Safety Class Items at the Savannah River Site (SRS) are selected in a consistent and technically defensible manner. Safety class items are those in the highest of four categories determined to be of special importance to nuclear safety and, merit appropriately higher-quality design, fabrication, and industrial test standards and codes. The identification of safety class items is approached using a cascading strategy that begins at the 'safety function' level (i.e., a cooling function, ventilation function, etc.) and proceeds down to the system, component, or structure level. Thus, the items that are required to support a safety function are SCls. The basic steps in this procedure apply to the determination of SCls for both new project activities, and for operating facilities. The GDC lists six characteristics of SCls to be considered as a starting point for safety item classification. They are as follows: 1. Those items whose failure would produce exposure consequences that would exceed the guidelines in Section 1300-1.4, ''Guidance on Limiting Exposure of the Public,'' at the site boundary or nearest point of public access 2. Those items required to maintain operating parameters within the safety limits specified in the Operational Safety Requirements during normal operations and anticipated operational occurrences. 3. Those items required for nuclear criticality safety. 4. Those items required to monitor the release of radioactive material to the environment during and after a Design Basis Accident. Those items required to achieve, and maintain the facility in a safe shutdown condition 6. Those items that control Safety Class Item listed above

  4. Optimization of air injection parameters toward optimum fuel saving effect for ships

    Science.gov (United States)

    Lee, Inwon; Park, Seong Hyeon

    2016-11-01

    Air lubrication method is the most promising commercial strategy for the frictional drag reduction of ocean going vessels. Air bubbles are injected through the array of holes or the slots installed onto the flat bottom surface of vessel and a sufficient supply of air is required to ensure the formation of stable air layer by the by the coalescence of the bubbles. The air layer drag reduction becomes economically meaningful when the power gain through the drag reduction exceeds the pumping power consumption. In this study, a model ship of 50k medium range tanker is employed to investigate air lubrication method. The experiments were conducted in the 100m long towing tank facility at the Pusan National University. To create the effective air lubrication with lower air flow rate, various configurations including the layout of injection holes, employment of side fences and static trim have been tested. In the preliminary series of model tests, the maximum 18.13%(at 15kts) of reduction of model resistance was achieved. This research was supported by the National Research Foundation of Korea (NRF) Grant funded by the Korea government (MEST) through GCRC-SOP (Grant No. 2011-0030013).

  5. Demonstration of Energy Savings in Commercial Buildings for Tiered Trim and Respond Method in Resetting Static Pressure for VAV Systems

    Science.gov (United States)

    2017-03-01

    Technology Certification Program EUI Energy Use Intensity EW Energy and Water GHG Greenhouse Gas GSM Global System for Mobile GWh Gigawatt hours...utility bill. Other charges could include basic service charge, transmission service charge, on-peak and off-peak demand charges, and franchise fee...Regulated Air Volume (TRAV) systems. ASHRAE Transactions 99(1):791-800. 106 15. Hartman, T. 1995. Global optimization strategies for high

  6. Situating methodology within qualitative research.

    Science.gov (United States)

    Kramer-Kile, Marnie L

    2012-01-01

    Qualitative nurse researchers are required to make deliberate and sometimes complex methodological decisions about their work. Methodology in qualitative research is a comprehensive approach in which theory (ideas) and method (doing) are brought into close alignment. It can be difficult, at times, to understand the concept of methodology. The purpose of this research column is to: (1) define qualitative methodology; (2) illuminate the relationship between epistemology, ontology and methodology; (3) explicate the connection between theory and method in qualitative research design; and 4) highlight relevant examples of methodological decisions made within cardiovascular nursing research. Although there is no "one set way" to do qualitative research, all qualitative researchers should account for the choices they make throughout the research process and articulate their methodological decision-making along the way.

  7. A unified flight control methodology for a compound rotorcraft in fundamental and aerobatic maneuvering flight

    Science.gov (United States)

    Thorsen, Adam

    This study investigates a novel approach to flight control for a compound rotorcraft in a variety of maneuvers ranging from fundamental to aerobatic in nature. Fundamental maneuvers are a class of maneuvers with design significance that are useful for testing and tuning flight control systems along with uncovering control law deficiencies. Aerobatic maneuvers are a class of aggressive and complex maneuvers with more operational significance. The process culminating in a unified approach to flight control includes various control allocation studies for redundant controls in trim and maneuvering flight, an efficient methodology to simulate non-piloted maneuvers with varying degrees of complexity, and the setup of an unconventional control inceptor configuration along with the use of a flight simulator to gather pilot feedback in order to improve the unified control architecture. A flight path generation algorithm was developed to calculate control inceptor commands required for a rotorcraft in aerobatic maneuvers. This generalized algorithm was tailored to generate flight paths through optimization methods in order to satisfy target terminal position coordinates or to minimize the total time of a particular maneuver. Six aerobatic maneuvers were developed drawing inspiration from air combat maneuvers of fighter jet aircraft: Pitch-Back Turn (PBT), Combat Ascent Turn (CAT), Combat Descent Turn (CDT), Weaving Pull-up (WPU), Combat Break Turn (CBT), and Zoom and Boom (ZAB). These aerobatic maneuvers were simulated at moderate to high advance ratios while fundamental maneuvers of the compound including level accelerations/decelerations, climbs, descents, and turns were investigated across the entire flight envelope to evaluate controller performance. The unified control system was developed to allow controls to seamlessly transition between manual and automatic allocations while ensuring that the axis of control for a particular inceptor remained constant with flight

  8. CSN-associated USP48 confers stability to nuclear NF-κB/RelA by trimming K48-linked Ub-chains.

    Science.gov (United States)

    Schweitzer, Katrin; Naumann, Michael

    2015-02-01

    Diligent balance of nuclear factor kappa B (NF-κB) activity is essential owing to NF-κB's decisive role in cellular processes including inflammation, immunity and cell survival. Ubiquitin/proteasome-system (UPS)-dependent degradation of activated NF-κB/RelA involves the cullin-RING-ubiquitin-ligase (CRL) ECS(SOCS1). The COP9 signalosome (CSN) controls ubiquitin (Ub) ligation by CRLs through the removal of the CRL-activating Ub-like modifier NEDD8 from their cullin subunits and through deubiquitinase (DUB) activity of associated DUBs. However, knowledge about DUBs involved in the regulation of NF-κB activity within the nucleus is scarce. In this study we observed that USP48, a DUB of hitherto ill-defined function identified through a siRNA screen, associates with the CSN and RelA in the nucleus. We show that USP48 trims rather than completely disassembles long K48-linked free and substrate-anchored Ub-chains, a catalytic property only shared with ataxin-3 (Atx3) and otubain-1 (OTU1), and that USP48 Ub-chain-trimming activity is regulated by casein-kinase-2 (CK2)-mediated phosphorylation in response to cytokine-stimulation. Functionally, we demonstrate for the first time the CSN and USP48 to cooperatively stabilize the nuclear pool of RelA, thereby facilitating timely induction and shutoff of NF-κB target genes. In summary, this study demonstrates that USP48, a nuclear DUB regulated by CK2, controls the UPS-dependent turnover of activated NF-κB/RelA in the nucleus together with the CSN. Thereby USP48 contributes to a timely control of immune responses. Copyright © 2014 Elsevier B.V. All rights reserved.

  9. Mutations in Four Glycosyl Hydrolases Reveal a Highly Coordinated Pathway for Rhodopsin Biosynthesis and N-Glycan Trimming in Drosophila melanogaster

    Science.gov (United States)

    Rosenbaum, Erica E.; Vasiljevic, Eva; Brehm, Kimberley S.; Colley, Nansi Jo

    2014-01-01

    As newly synthesized glycoproteins move through the secretory pathway, the asparagine-linked glycan (N-glycan) undergoes extensive modifications involving the sequential removal and addition of sugar residues. These modifications are critical for the proper assembly, quality control and transport of glycoproteins during biosynthesis. The importance of N-glycosylation is illustrated by a growing list of diseases that result from defects in the biosynthesis and processing of N-linked glycans. The major rhodopsin in Drosophila melanogaster photoreceptors, Rh1, is highly unique among glycoproteins, as the N-glycan appears to be completely removed during Rh1 biosynthesis and maturation. However, much of the deglycosylation pathway for Rh1 remains unknown. To elucidate the key steps in Rh1 deglycosylation in vivo, we characterized mutant alleles of four Drosophila glycosyl hydrolases, namely α-mannosidase-II (α-Man-II), α-mannosidase-IIb (α-Man-IIb), a β-N-acetylglucosaminidase called fused lobes (Fdl), and hexosaminidase 1 (Hexo1). We have demonstrated that these four enzymes play essential and unique roles in a highly coordinated pathway for oligosaccharide trimming during Rh1 biosynthesis. Our results reveal that α-Man-II and α-Man-IIb are not isozymes like their mammalian counterparts, but rather function at distinct stages in Rh1 maturation. Also of significance, our results indicate that Hexo1 has a biosynthetic role in N-glycan processing during Rh1 maturation. This is unexpected given that in humans, the hexosaminidases are typically lysosomal enzymes involved in N-glycan catabolism with no known roles in protein biosynthesis. Here, we present a genetic dissection of glycoprotein processing in Drosophila and unveil key steps in N-glycan trimming during Rh1 biosynthesis. Taken together, our results provide fundamental advances towards understanding the complex and highly regulated pathway of N-glycosylation in vivo and reveal novel insights into the

  10. Mutations in four glycosyl hydrolases reveal a highly coordinated pathway for rhodopsin biosynthesis and N-glycan trimming in Drosophila melanogaster.

    Directory of Open Access Journals (Sweden)

    Erica E Rosenbaum

    2014-05-01

    Full Text Available As newly synthesized glycoproteins move through the secretory pathway, the asparagine-linked glycan (N-glycan undergoes extensive modifications involving the sequential removal and addition of sugar residues. These modifications are critical for the proper assembly, quality control and transport of glycoproteins during biosynthesis. The importance of N-glycosylation is illustrated by a growing list of diseases that result from defects in the biosynthesis and processing of N-linked glycans. The major rhodopsin in Drosophila melanogaster photoreceptors, Rh1, is highly unique among glycoproteins, as the N-glycan appears to be completely removed during Rh1 biosynthesis and maturation. However, much of the deglycosylation pathway for Rh1 remains unknown. To elucidate the key steps in Rh1 deglycosylation in vivo, we characterized mutant alleles of four Drosophila glycosyl hydrolases, namely α-mannosidase-II (α-Man-II, α-mannosidase-IIb (α-Man-IIb, a β-N-acetylglucosaminidase called fused lobes (Fdl, and hexosaminidase 1 (Hexo1. We have demonstrated that these four enzymes play essential and unique roles in a highly coordinated pathway for oligosaccharide trimming during Rh1 biosynthesis. Our results reveal that α-Man-II and α-Man-IIb are not isozymes like their mammalian counterparts, but rather function at distinct stages in Rh1 maturation. Also of significance, our results indicate that Hexo1 has a biosynthetic role in N-glycan processing during Rh1 maturation. This is unexpected given that in humans, the hexosaminidases are typically lysosomal enzymes involved in N-glycan catabolism with no known roles in protein biosynthesis. Here, we present a genetic dissection of glycoprotein processing in Drosophila and unveil key steps in N-glycan trimming during Rh1 biosynthesis. Taken together, our results provide fundamental advances towards understanding the complex and highly regulated pathway of N-glycosylation in vivo and reveal novel insights

  11. Event Sequence Analysis of the Air Intelligence Agency Information Operations Center Flight Operations

    National Research Council Canada - National Science Library

    Larsen, Glen

    1998-01-01

    This report applies Event Sequence Analysis, methodology adapted from aircraft mishap investigation, to an investigation of the performance of the Air Intelligence Agency's Information Operations Center (IOC...

  12. Air surveillance

    International Nuclear Information System (INIS)

    Patton, G.W.

    1995-01-01

    This section of the 1994 Hanford Site Environmental Report summarizes the air surveillance and monitoring programs currently in operation at that Hanford Site. Atmospheric releases of pollutants from Hanford to the surrounding region are a potential source of human exposure. For that reason, both radioactive and nonradioactive materials in air are monitored at a number of locations. The influence of Hanford emissions on local radionuclide concentrations was evaluated by comparing concentrations measured at distant locations within the region to concentrations measured at the Site perimeter. This section discusses sample collection, analytical methods, and the results of the Hanford air surveillance program. A complete listing of all analytical results summarized in this section is reported separately by Bisping (1995)

  13. Air surveillance

    Energy Technology Data Exchange (ETDEWEB)

    Patton, G.W.

    1995-06-01

    This section of the 1994 Hanford Site Environmental Report summarizes the air surveillance and monitoring programs currently in operation at that Hanford Site. Atmospheric releases of pollutants from Hanford to the surrounding region are a potential source of human exposure. For that reason, both radioactive and nonradioactive materials in air are monitored at a number of locations. The influence of Hanford emissions on local radionuclide concentrations was evaluated by comparing concentrations measured at distant locations within the region to concentrations measured at the Site perimeter. This section discusses sample collection, analytical methods, and the results of the Hanford air surveillance program. A complete listing of all analytical results summarized in this section is reported separately by Bisping (1995).

  14. Air pollution

    International Nuclear Information System (INIS)

    Feugier, A.

    1996-01-01

    The air pollution results from the combustion of petroleum products, natural gas, coal, wastes and transports. Some compounds are considered as particularly pollutants: the carbon monoxide, the nitrogen oxides, the tropospheric ozone and the sulfur dioxides. Their environmental and biological effects are described. The present political guide lines concerns the combustion plants, the ozone, the wastes incineration and the vehicles emissions. The aim is at some future date to control the air quality, to reduce the volatile organic compounds emissions and to limit the sulfur rate of some petroleum products. (O.L.)

  15. Methodological Problems of Nanotechnoscience

    Science.gov (United States)

    Gorokhov, V. G.

    Recently, we have reported on the definitions of nanotechnology as a new type of NanoTechnoScience and on the nanotheory as a cluster of the different natural and engineering theories. Nanotechnology is not only a new type of scientific-engineering discipline, but it evolves also in a “nonclassical” way. Nanoontology or nano scientific world view has a function of the methodological orientation for the choice the theoretical means and methods toward a solution to the scientific and engineering problems. This allows to change from one explanation and scientific world view to another without any problems. Thus, nanotechnology is both a field of scientific knowledge and a sphere of engineering activity, in other words, NanoTechnoScience is similar to Systems Engineering as the analysis and design of large-scale, complex, man/machine systems but micro- and nanosystems. Nano systems engineering as well as Macro systems engineering includes not only systems design but also complex research. Design orientation has influence on the change of the priorities in the complex research and of the relation to the knowledge, not only to “the knowledge about something”, but also to the knowledge as the means of activity: from the beginning control and restructuring of matter at the nano-scale is a necessary element of nanoscience.

  16. Methodological themes and variations

    International Nuclear Information System (INIS)

    Tetlock, P.E.

    1989-01-01

    This paper reports on the tangible progress that has been made in clarifying the underlying processes that affect both the likelihood of war in general and of nuclear war in particular. It also illustrates how difficult it is to make progress in this area. Nonetheless, what has been achieved should not be minimized. We have learned a good deal on both the theoretical and the methodological fronts and, perhaps, most important, we have learned a good deal about the limits of our knowledge. Knowledge of our ignorance---especially in a policy domain where confident, even glib, causal assertions are so common---can be a major contribution in itself. The most important service the behavioral and social sciences can currently provide to the policy making community may well be to make thoughtful skepticism respectable: to sensitize those who make key decisions to the uncertainty surrounding our understanding of international conflict and to the numerous qualifications that now need to be attached to simple causal theories concerning the origins of war

  17. Engineering radioecology: Methodological considerations

    International Nuclear Information System (INIS)

    Nechaev, A.F.; Projaev, V.V.; Sobolev, I.A.; Dmitriev, S.A.

    1995-01-01

    The term ''radioecology'' has been widely recognized in scientific and technical societies. At the same time, this scientific school (radioecology) does not have a precise/generally acknowledged structure, unified methodical basis, fixed subjects of investigation, etc. In other words, radioecology is a vast, important but rather amorphous conglomerate of various ideas, amalgamated mostly by their involvement in biospheric effects of ionizing radiation and some conceptual stereotypes. This paradox was acceptable up to a certain time. However, with the termination of the Cold War and because of remarkable political changes in the world, it has become possible to convert the problem of environmental restoration from the scientific sphere in particularly practical terms. Already the first steps clearly showed an imperfection of existing technologies, managerial and regulatory schemes; lack of qualified specialists, relevant methods and techniques; uncertainties in methodology of decision-making, etc. Thus, building up (or maybe, structuring) of special scientific and technological basis, which the authors call ''engineering radioecology'', seems to be an important task. In this paper they endeavored to substantiate the last thesis and to suggest some preliminary ideas concerning the subject matter of engineering radioecology

  18. Air pollution

    International Nuclear Information System (INIS)

    Anon.

    2008-01-01

    Air pollution has accompanied and developed with the industrial age, since its beginnings. This very complete review furnishes the toxicological data available for the principal pollutants and assesses the epidemiologic studies thus far conducted. It also describes European regulations and international commitments for the reduction of emissions. (author)

  19. Air quality

    International Nuclear Information System (INIS)

    1995-01-01

    This chapter of the 'Assessment of the state of the environment in Lebanon' describes the air quality and identifies the most important air quality issues. Baseline information about the factors affecting dispersion and the climate of Lebanon presents as well and overall estimation of total emissions in Lebanon. Emissions from vehicles, electricity and power plants generation are described. Industrial emitters of air pollutants are described for each kind of industry i.e.cement plants, Selaata fertilizer factory, sugar-beet factory, refineries and for those derived from the use of leaded fuel . Impact of economic and human activities on air quality in Lebanon (especially in Beirut and Tripoli) are quantified by quantities of CO 2 , SO 2 , NO x , total suspended particulates(TSP), deposition and their environmental effects on health. In abscence of emissions monitoring, data available are expressed in terms of fuel use, output and appropriate empirical factors, national output and workfores sizes. Finally key issues and some potential mitigation /management approaches are presented

  20. Urban air quality management. V. 1

    International Nuclear Information System (INIS)

    1997-01-01

    This is the first in a series of reports commissioned by the International Petroleum Industry Environmental Conservation Association (IPIECA) to represent members' views on the management of urban air quality in the growing cities in developing countries. In this report, a general, science based framework is provided as a basis for understanding the nature of the problem in any specific urban area, the range of solutions that might be available, and the potential impact of each solution and its least cost privatisation. The topics covered are: a process for urban air quality management; setting air quality targets; a structured approach to the assessment of current and future air quality modelling methodologies; identification and collation of air quality model input data; development of socio-economic scenarios -long-term trend forecasting; cost effectiveness studies; the IPIECA approach to urban air quality management - development of partnerships; encouraging commitment to implementation of programme recommendations. (7 figures; 2 tables; 18 references). (UK)

  1. Royal Danish Air Force. Air Operations Doctrine

    DEFF Research Database (Denmark)

    Nørby, Søren

    This brief examines the development of the first Danish Air Force Air Operations Doctrine, which was officially commissioned in October 1997 and remained in effect until 2010. The development of a Danish air power doctrine was heavily influenced by the work of Colonel John Warden (USAF), both...... through his book ”The Air Campaign” and his subsequent planning of the air campaign against Iraq in 1990-1991. Warden’s ideas came to Denmark and the Danish Air Force by way of Danish Air Force students attending the United States Air Force Air University in Alabama, USA. Back in Denmark, graduates from...... the Air University inspired a small number of passionate airmen, who then wrote the Danish Air Operations Doctrine. The process was supported by the Air Force Tactical Command, which found that the work dovetailed perfectly with the transformation process that the Danish Air Force was in the midst...

  2. Dosimetric methodology of the ICRP

    International Nuclear Information System (INIS)

    Eckerman, K.F.

    1994-01-01

    Establishment of guidance for the protection of workers and members of the public from radiation exposures necessitates estimation of the radiation dose to tissues of the body at risk. The dosimetric methodology formulated by the International Commission on Radiological Protection (ICRP) is intended to be responsive to this need. While developed for radiation protection, elements of the methodology are often applied in addressing other radiation issues; e.g., risk assessment. This chapter provides an overview of the methodology, discusses its recent extension to age-dependent considerations, and illustrates specific aspects of the methodology through a number of numerical examples

  3. Transmission pricing: paradigms and methodologies

    Energy Technology Data Exchange (ETDEWEB)

    Shirmohammadi, Dariush [Pacific Gas and Electric Co., San Francisco, CA (United States); Vieira Filho, Xisto; Gorenstin, Boris [Centro de Pesquisas de Energia Eletrica (CEPEL), Rio de Janeiro, RJ (Brazil); Pereira, Mario V.P. [Power System Research, Rio de Janeiro, RJ (Brazil)

    1994-12-31

    In this paper we describe the principles of several paradigms and methodologies for pricing transmission services. The paper outlines some of the main characteristics of these paradigms and methodologies such as where they may be used for best results. Due to their popularity, power flow based MW-mile and short run marginal cost pricing methodologies will be covered in some detail. We conclude the paper with examples of the application of these two pricing methodologies for pricing transmission services in Brazil. (author) 25 refs., 2 tabs.

  4. Analytical methodology for nuclear safeguards

    International Nuclear Information System (INIS)

    Ramakumar, K.L.

    2011-01-01

    This paper attempts to briefly describe the analytical methodologies available and also highlight some of the challenges, expectations from nuclear material accounting and control (NUMAC) point of view

  5. Country report: a methodology

    International Nuclear Information System (INIS)

    Colin, A.

    2013-01-01

    This paper describes a methodology which could be applicable to establish a country report. In the framework of nuclear non proliferation appraisal and IAEA safeguards implementation, it is important to be able to assess the potential existence of undeclared nuclear materials and activities as undeclared facilities in the country under review. In our views a country report should aim at providing detailed information on nuclear related activities for each country examined taken 'as a whole' such as nuclear development, scientific and technical capabilities, etc. In order to study a specific country, we need to know if there is already an operating nuclear civil programme or not. In the first case, we have to check carefully if it could divert nuclear material, if there are misused declared facilities or if they operate undeclared facilities and conduct undeclared activities aiming at manufacturing nuclear weapon. In the second case, we should pay attention to the development of a nuclear civil project. A country report is based on a wide span of information (most of the time coming from open sources but sometimes coming also from confidential or private ones). Therefore, it is important to carefully check the nature and the credibility (reliability?) of these sources through cross-check examination. Eventually, it is necessary to merge information from different sources and apply an expertise filter. We have at our disposal a lot of performing tools to help us to assess, understand and evaluate the situation (cartography, imagery, bibliometry, etc.). These tools allow us to offer the best conclusions as far as possible. The paper is followed by the slides of the presentation. (author)

  6. Microbiological Methodology in Astrobiology

    Science.gov (United States)

    Abyzov, S. S.; Gerasimenko, L. M.; Hoover, R. B.; Mitskevich, I. N.; Mulyukin, A. L.; Poglazova, M. N.; Rozanov, A. Y.

    2005-01-01

    Searching for life in astromaterials to be delivered from the future missions to extraterrestrial bodies is undoubtedly related to studies of the properties and signatures of living microbial cells and microfossils on Earth. As model terrestrial analogs of Martian polar subsurface layers are often regarded the Antarctic glacier and Earth permafrost habitats where alive microbial cells preserved viability for millennia years due to entering the anabiotic state. For the future findings of viable microorganisms in samples from extraterrestrial objects, it is important to use a combined methodology that includes classical microbiological methods, plating onto nutrient media, direct epifluorescence and electron microscopy examinations, detection of the elemental composition of cells, radiolabeling techniques, PCR and FISH methods. Of great importance is to ensure authenticity of microorganisms (if any in studied samples) and to standardize the protocols used to minimize a risk of external contamination. Although the convincing evidence of extraterrestrial microbial life will may come from the discovery of living cells in astromaterials, biomorphs and microfossils must also be regarded as a target in search of life evidence bearing in mind a scenario that alive microorganisms had not be preserved and underwent mineralization. Under the laboratory conditions, processes that accompanied fossilization of cyanobacteria were reconstructed, and artificially produced cyanobacterial stromatolites resembles by their morphological properties those found in natural Earth habitats. Regarding the vital importance of distinguishing between biogenic and abiogenic signatures and between living and fossil microorganisms in analyzed samples, it is worthwhile to use some previously developed approaches based on electron microscopy examinations and analysis of elemental composition of biomorphs in situ and comparison with the analogous data obtained for laboratory microbial cultures and

  7. Kaupapa Maori Methodology: Trusting the Methodology through Thick and Thin

    Science.gov (United States)

    Hiha, Anne Aroha

    2016-01-01

    Kaupapa Maori is thoroughly theorised in academia in Aotearoa and those wishing to use it as their research methodology can find support through the writing of a number of Maori academics. What is not so well articulated, is the experiential voice of those who have used Kaupapa Maori as research methodology. My identity as a Maori woman…

  8. Effects of Inlet Modification and Rocket-Rack Extension on the Longitudinal Trim and Low-Lift Drag of the Douglas F5D-1 Airplane as Obtained with a 0.125-Scale Rocket-Boosted Model Between Mach Numbers of 0.81 and 1.64: TED No. NACA AD 399

    Science.gov (United States)

    Hastings, Earl C., Jr.; Dickens, Waldo L.

    1957-01-01

    A flight investigation was conducted to determine the effects of inlet modification and rocket-rack extension on the longitudinal trim and low-lift drag of the Douglas F5D-1 airplane. The investigation was conducted with a 0.125-scale rocket-boosted model between Mach Numbers of 0.81 and 1.64. This paper presents the changes in trim angle of attack, trim lift coefficient, and low-lift drag caused by the modified inlets alone over a small part of the test Mach number range and by a combination of the modified inlets and extended rocket racks throughout the remainder of the test.

  9. [Quality and integrity in the production and publication of scientific results: data trimming, manipulation and (self) plagiarism].

    Science.gov (United States)

    Lüscher, T F

    2014-08-01

    The publication of scientific manuscripts is an essential part in the research process and in the attempt to produce novel knowledge: only what is published exists. It is the aim of research to produce reproducible and sustainable knowledge. Reproducible knowledge is based on precise observation, the use of modern methodologies and an appropriate statistical analysis. As a consequence, it must be the intention of any scientist to report the truth and nothing but the truth. This principle requires precision and honesty. Deviation from such a behavior may lead to scientific misconduct: It encompasses the use of inappropriate methods and/or statistics, double publication of data, sloppy data presentation and processing, up to data massaging, manipulation, data theft or fabrication. Famous examples can be found throughout the history of research but it appears that such behavior has recently become more common possibly due to excessive competition, the crucial role of grants for scientific productivity and funding as well as promotion. Accordingly, in the training of researchers it seems essential to emphasize the importance of precise data acquisition and analysis to ascertain reproducible data. Similarly, it must be assured that data sets are only published once, that authors have contributed technically and/or intellectually in an important manner and that the work of other scientists is cited appropriately. Editors and reviewers should carefully assess the quality of submitted manuscripts. In fact, it is the aim of the peer review process to assure as much as possible that the quality of submitted manuscripts meets current methodological as well as ethical standards.

  10. Air quality

    International Nuclear Information System (INIS)

    Anon.

    1996-01-01

    The anthropic pollution sources are essentially industrial or bound to transport. A phenomenon of these last twenty years is the decreasing of the industrial pollution and the increasing of pollution coming from automobiles. Emissions of furans and dioxines coming from municipal wastes are measured. A special attention is mentioned for polycyclic aromatic hydrocarbons coming from incomplete combustions. A last aspect of air pollution is studied with the effect on man, ecosystems and materials, by modeling or direct measurements. (N.C.)

  11. Air pollution

    International Nuclear Information System (INIS)

    Nelson, P.

    2000-01-01

    Australian cites experience a number of current and emerging air pollution problems. Concentrations of traditional primary pollutants such as CO, lead and dust have fallen in recent years as a consequence of air pollutant control measures, and the widespread introduction of lead-free petrol. However, recommended guidelines for ozone, the principal component of photochemical smog, are regularly exceeded in major capital cities in the summer months. In addition, it is predicted that extensive urban expansion will lead to much greater dependence on the motor vehicle as the primary means of transportation. Effects of air pollution are felt at a variety of scales. Traditionally, concerns about gaseous and particulate emissions from industrial and vehicular sources were focused on local impacts due to exposure to toxic species such as CO and lead. As noted above, concentrations of these pollutants have been reduced by a variety of control measures. Pollutants which have effects at a regional scale, such as photochemically-produced ozone, and acidic gases and particles have proved more difficult to reduce. In general, these pollutants arc not the result of direct emissions to atmosphere, but result from complex secondary processes driven by photochemical reactions of species such as NO 2 and aldehydes. In addition, global effects of gaseous and particulate emissions to the atmosphere have received significant recent attention, concentrations of atmospheric CO 2 with predicted impacts on global climate, and ozone depletion due to anthropogenic emissions of chlorine-containing chemicals are the two major examples. Combustion processes from petrol- and diesel-fuelled vehicles, make major contributions to air pollution, and the magnitude of this contribution is discussed in this article

  12. Air filtration and indoor air quality

    DEFF Research Database (Denmark)

    Bekö, Gabriel

    2006-01-01

    Demands for better indoor air quality are increasing, since we spend most of our time indoors and we are more and more aware of indoor air pollution. Field studies in different parts of the world have documented that high percentage of occupants in many offices and buildings find the indoor air...... decent ventilation and air cleaning/air filtration, high indoor air quality cannot be accomplished. The need for effective air filtration has increased with increasing evidence on the hazardous effects of fine particles. Moreover, the air contains gaseous pollutants, removal of which requires various air...... cleaning techniques. Supply air filter is one of the key components in the ventilation system. Studies have shown that used ventilation filters themselves can be a significant source of indoor air pollution with consequent impact on perceived air quality, sick building syndrome symptoms and performance...

  13. LIFE CYCLE DESIGN OF AIR INTAKE MANIFOLDS; PHASE I: 2.0 L FORD CONTOUR AIR INTAKE MANIFOLD

    Science.gov (United States)

    The project team applied the life cycle design methodology to the design analysis of three alternative air intake manifolds: a sand cast aluminum, brazed aluminum tubular, and nylon composite. The design analysis included a life cycle inventory analysis, environmental regulatory...

  14. Development of a novel methodology for indoor emission source identification

    DEFF Research Database (Denmark)

    Han, K.H.; Zhang, J.S.; Knudsen, H.N.

    2011-01-01

    The objective of this study was to develop and evaluate a methodology to identify individual sources of emissions based on the measurements of mixed air samples and the emission signatures of individual materials previously determined by Proton Transfer Reaction-Mass Spectrometry (PTR-MS), an on......-line analytical device. The methodology based on signal processing principles was developed by employing the method of multiple regression least squares (MRLS) and a normalization technique. Samples of nine typical building materials were tested individually and in combination, including carpet, ceiling material...... experiments and investigation are needed for cases where the relative emission rates among different compounds may change over a long-term period....

  15. A methodology for social experimentation

    DEFF Research Database (Denmark)

    Ravn, Ib

    A methodology is outlined whereby one may improve the performance of a social system to the satisfaction of its stakeholders, that is, facilitate desirable social and organizational transformations......A methodology is outlined whereby one may improve the performance of a social system to the satisfaction of its stakeholders, that is, facilitate desirable social and organizational transformations...

  16. Workshops as a Research Methodology

    Science.gov (United States)

    Ørngreen, Rikke; Levinsen, Karin

    2017-01-01

    This paper contributes to knowledge on workshops as a research methodology, and specifically on how such workshops pertain to e-learning. A literature review illustrated that workshops are discussed according to three different perspectives: workshops as a means, workshops as practice, and workshops as a research methodology. Focusing primarily on…

  17. Methodological Pluralism and Narrative Inquiry

    Science.gov (United States)

    Michie, Michael

    2013-01-01

    This paper considers how the integral theory model of Nancy Davis and Laurie Callihan might be enacted using a different qualitative methodology, in this case the narrative methodology. The focus of narrative research is shown to be on "what meaning is being made" rather than "what is happening here" (quadrant 2 rather than…

  18. Building ASIPS the Mescal methodology

    CERN Document Server

    Gries, Matthias

    2006-01-01

    A number of system designers use ASIP's rather than ASIC's to implement their system solutions. This book gives a comprehensive methodology for the design of these application-specific instruction processors (ASIPs). It includes demonstrations of applications of the methodologies using the Tipi research framework.

  19. A methodology for software documentation

    OpenAIRE

    Torres Júnior, Roberto Dias; Ahlert, Hubert

    2000-01-01

    With the growing complexity of window based software and the use of object-oriented, the development of software is getting more complex than ever. Based on that, this article intends to present a methodology for software documentation and to analyze our experience and how this methodology can aid the software maintenance

  20. AEGIS methodology and a perspective from AEGIS methodology demonstrations

    International Nuclear Information System (INIS)

    Dove, F.H.

    1981-03-01

    Objectives of AEGIS (Assessment of Effectiveness of Geologic Isolation Systems) are to develop the capabilities needed to assess the post-closure safety of waste isolation in geologic formation; demonstrate these capabilities on reference sites; apply the assessment methodology to assist the NWTS program in site selection, waste package and repository design; and perform repository site analyses for the licensing needs of NWTS. This paper summarizes the AEGIS methodology, the experience gained from methodology demonstrations, and provides an overview in the following areas: estimation of the response of a repository to perturbing geologic and hydrologic events; estimation of the transport of radionuclides from a repository to man; and assessment of uncertainties