Neutron detection of the Triga Mark III reactor, using nuclear track methodology

Energy Technology Data Exchange (ETDEWEB)

Espinosa, G., E-mail: espinosa@fisica.unam.mx; Golzarri, J. I. [Instituto de Física, Universidad Nacional Autónoma de México Circuito de la Investigación Científica, Ciudad Universitaria. México, DF (Mexico); Raya-Arredondo, R.; Cruz-Galindo, S. [Instituto Nacional de Investigaciones Nucleares (Mexico); Sajo-Bohus, L. [Universidad Simón Bolivar, Laboratorio de Física Nuclear, Caracas (Venezuela, Bolivarian Republic of)

2015-07-23

Nuclear Track Methodology (NTM), based on the neutron-proton interaction is one often employed alternative for neutron detection. In this paper we apply NTM to determine the Triga Mark III reactor operating power and neutron flux. The facility nuclear core, loaded with 85 Highly Enriched Uranium as fuel with control rods in a demineralized water pool, provide a neutron flux around 2 × 10{sup 12} n cm{sup −2} s{sup −1}, at the irradiation channel TO-2. The neutron field is measured at this channel, using Landauer{sup ®} PADC as neutron detection material, covered by 3 mm Plexiglas{sup ®} as converter. After exposure, plastic detectors were chemically etched to make observable the formed latent tracks induced by proton recoils. The track density was determined by a custom made Digital Image Analysis System. The resulting average nuclear track density shows a direct proportionality response for reactor power in the range 0.1-7 kW. We indicate several advantages of the technique including the possibility to calibrate the neutron flux density measured at low reactor power.

76 FR 53533 - Notification of New Pricing Methodology

Science.gov (United States)

2011-08-26

... products. The new pricing methodology is based primarily on the London Fix weekly average (average of the... DEPARTMENT OF THE TREASURY United States Mint Notification of New Pricing Methodology ACTION: Notice. SUMMARY: The United States Mint is implementing a new pricing methodology for its commemorative...

III Scientific-technical conference. Problems and outlooks for development of chemical and radiochemical control in atomic energetics (Atomenergoanalytics-2005). Summaries of reports

International Nuclear Information System (INIS)

2005-01-01

Summaries of reports of the III Scientific-technical conference: Problems and outlooks for development of chemical and radiochemical control in atomic energetics (Atomenergoanalytics-2005) are presented. The conference performed 20-22 September, 2005, in Sosnovyj Bor. Problems of methodical, instrumental and metrological supply of chemical, radiochemical and radiometric control at active NPP and NPU, modern concepts of construction of automated systems of chemical and radiometric control in the atomic energetics, directions for the decision of questions in organization and conducting of chemical and radiochemical control of water-chemical regimes of NPP and NPU are discussed [ru

PAGIS summary report of phase 1: a common methodological approach based on European data and models

International Nuclear Information System (INIS)

Cadelli, N.; Cottone, G.; Bertozzi, G.; Girardi, F.

1984-01-01

Since 1982 a joint study has been launched by the CEC with the participation of national institutions in the E.C., aiming at a Performance Assessment of Geological Isolation Systems (PAGIS) for HLW disposal. This document is a summary of the first phase of the study which was devoted to the collection of data and models and to the choice of an appropriate methodology. To this purpose, real or national sites have been chosen, which are representative of three types of continental geological formations in the E.C.: clay, granite and salt (although the choices imply no committment of any kind about their final use). Moreover, sub-seabed areas have also been identified. The study covers the following items: - basic data on waste characteristics, site data and repository designs; - methodology, which allows sensitivity and uncertainty analyses to be performed, as well as the assessment of radiation doses to individuals and populations; - preliminary modelling of radionuclide release and migration through the geosphere (near- and far-field) and the biosphere following their various pathways to man; - selection of the most relevant radionuclide release scenarios and their probability of occurrence. Reference values have been selected for the basic data as well as variants covering the various options which are under consideration in the different Countries of the E.C.

77 FR 48167 - Approved Tribal-State Class III Gaming Compact; Indian Gaming

Science.gov (United States)

2012-08-13

... DEPARTMENT OF THE INTERIOR Bureau of Indian Affairs Approved Tribal--State Class III Gaming Compact; Indian Gaming AGENCY: Bureau of Indian Affairs, Interior. ACTION: Notice of Approved Tribal--State Class III Gaming Compact. SUMMARY: This notice publishes an approval of the gaming compact between...

Type III Intermediate Filaments Desmin, Glial Fibrillary Acidic Protein (GFAP), Vimentin, and Peripherin

NARCIS (Netherlands)

Hol, Elly M; Capetanaki, Yassemi

2017-01-01

SummaryType III intermediate filament (IF) proteins assemble into cytoplasmic homopolymeric and heteropolymeric filaments with other type III and some type IV IFs. These highly dynamic structures form an integral component of the cytoskeleton of muscle, brain, and mesenchymal cells. Here, we review

Evaluation of safeguards procedures: a summary of a methodology

International Nuclear Information System (INIS)

Salisbury, J.D.; Savage, J.W.

1979-01-01

A methodology for the evaluation of safeguards procedures is described. As presently conceptualized, the methodology will consist of the following steps: (1) expansion of the general protection requirements that are contained in the NRC regulations into more detailed but still generic requirements for use at the working level; (2) development of techniques and formats for using the working-level requirements in an evaluation; (3) development of a technique for converting specific facility protection procedures into a format that will allow comparison with the working-level requirements; (4) development of an evaluation technique for comparing the facility protection procedures to determine if they meet the protection requirements

Summary

International Nuclear Information System (INIS)

2004-01-01

The fourth workshop of the OECD/NEA Forum on Stakeholder Confidence (FSC) was hosted by ONDRAF/NIRAS, the Belgian Agency for Radioactive Waste Management and enriched fissile materials. The central theme of the workshop was ''Dealing with interests, values and knowledge in managing risk''within the Belgian context of local partnerships for the long term management of low-level, short-lived radioactive waste. The four-day workshop started with a half-day session in Brussels giving a general introduction on the Belgian context and the local partnership methodology. This was followed by community visits to three local partnerships, PaLoFF in Fleurus-Farciennes, MONA in Mol, and STOLA in Dessel. After the visits, the workshop continued with two full-day sessions in Brussels. One hundred and nineteen registered participants, representing 13 countries, attended the workshop or participated in the community visits. About two thirds were Belgian stakeholders; the remainder came from FSC member organisations. The participants included representatives of municipal governments, civil society organisations, government agencies, industrial companies, the media, and international organisations as well as private citizens, consultants and academics. This Executive Summary gives an overview of the presentations and discussions that took place at the workshop and the community visits. The structure of the Executive Summary follows the structure of the workshop itself. Complementary to this Executive Summary and also provided with this document, is a NEA Secretariat's reflection aiming to place the main lessons of the workshop into an international perspective. (author)

Methodology for quantitative evalution of diagnostic performance. Project III

International Nuclear Information System (INIS)

Metz, C.E.

1985-01-01

Receiver Operation Characteristic (ROC) methodology is now widely recognized as the most satisfactory approach to the problem of measuring and specifying the performance of a diagnostic procedure. The primary advantage of ROC analysis over alternative methodologies is that it seperates differences in diagnostic accuracy that are due to actual differences in discrimination capacity from those that are due to decision threshold effects. Our effort during the past year has been devoted to developing digital computer programs for fitting ROC curves to diagnostic data by maximum likelihood estimation and to developing meaningful and valid statistical tests for assessing the significance of apparent differences between measured ROC curves. FORTRAN programs previously written here for ROC curve fitting and statistical testing have been refined to make them easier to use and to allow them to be run in a large variety of computer systems. We have attempted also to develop two new curve-fitting programs: one for conventional ROC data that assumes a different functional form for the ROC curve, and one that can be used for ''free-response'' ROC data. Finally, we have cooperated with other investigators to apply our techniques to analyze ROC data generated in clinical studies, and we have sought to familiarize the medical community with the advantages of ROC methodology. 36 ref

International Working Group on Fast Reactors Thirteenth Annual Meeting. Summary Report. Part II

International Nuclear Information System (INIS)

1980-10-01

The Thirteenth Annual Meeting of the IAEA International Working Group on Fast Reactors was held at the IAEA Headquarters, Vienna, Austria from 9 to 11 April 1980. The Summary Report (Part I) contains the Minutes of the Meeting. The Summary Report (Part II) contains the papers which review the national programme in the field of LMFBRs and other presentations at the Meeting. The Summary Report (Part III) contains the discussions on the review of the national programmes

International Working Group on Fast Reactors Thirteenth Annual Meeting. Summary Report. Part I

International Nuclear Information System (INIS)

1980-09-01

The Thirteenth Annual Meeting of the IAEA International Working Group on Fast Reactors was held at the IAEA Headquarters, Vienna, Austria from 9 to 11 April 1980. The Summary Report (Part I) contains the Minutes of the Meeting. The Summary Report (Part II) contains the papers which review the national programme in the field of LMFBRs and other presentations at the Meeting. The Summary Report (Part III) contains the discussions on the review of the national programmes

FutureTox III: Bridges for Translation | Science Inventory | US ...

Science.gov (United States)

The present document describes key discussion points and outcomes of a Society of Toxicology (SOT) Contemporary Concepts in Toxicology (CCT) Workshop, entitled FutureTox III1,2 that was held in Crystal City, Virginia, November 19-20, 2015. The workshop built on the many lessons learned from the first 10 years of TT21 and the first two workshops in the FutureTox series (for summary of FutureTox II see (Knudsen et al., 2015); for summary of FutureTox I see (Rowlands et al., 2014)). FutureTox III was attended in person and via webcast by more than 300 scientists from government research and regulatory agencies, research institutes, academia, and the chemical and pharmaceutical industries in Europe, Canada, and the United States. The meeting materials for FutureTox III, currently available to meeting registrants at http://www.toxicology.org/events/shm/cct/meetings.asp#upcoming-pnl-open, will be open to the public on November 29, 2016. At this workshop, participants reviewed and discussed the state of the science in toxicology and human risk and exposure assessment with a focus on moving TT21 science into the arena of regulatory decision-making. This manuscript describes the outcome of the FutureTox III 'contemporary concepts in toxicology' conference of the Society Toxicology, held November 2015 in Crystal City VA.

New methodologies for living material imaging. Compilation of summaries

International Nuclear Information System (INIS)

Barabino, Gabriele; Beaurepaire, Emmanuel; Betrouni, Nacim; Montagnat, Johan; Moonen, Chrit; Olivo-Marin, Jean-Christophe; Paul-Gilloteaux, Perrine; Tillement, Olivier; Barbier, Emmanuel; Beuf, Olivier; Chamot, Christophe; Clarysse, Patrick; Coll, Jean-Luc; Dojat, Michel; Lartizien, Carole; Peyrin, Francoise; Ratiney, Helene; Texier-Nogues, Isabelle; Usson, Yves; Vial, Jean-Claude; Gaillard, Sophie; Aubry, Jean-Francois; Barillot, Christian; Betrouni, Nacim; Beloeil, Jean-Claude; Bernard, Monique; Bridal, Lori; Coll, Jean-Luc; Cozzone, Patrick; Cuenod, Charles-Andre; Darrasse, Luc; Franconi, Jean-Michel; Frapart, Yves-Michel; Grenier, Nicolas; Guilloteau, Denis; Laniece, Philippe; Guilloteau, Denis; Laniece, Philippe; Lethimonnier, Franck; Moonen, Chrit; Pain, Frederic; Patat, Frederic; Tanter, Mickael; Trebossen, Regine; Van Beers, Bernard; Visvikis, Dimitris; Buvat, Irene; Carrault, Guy; Frouin, Frederique; Kouame, Denis; Meste, Olivier; Peyrin, Francoise; Brasse, David; Buvat, Irene; Dauvergne, Denis; Haddad, Ferid; Menard, Laurent; Ouadi, Ali; Olivo-Marin, Jean-Christophe; Pansu, Robert; Peyrieras, Nadine; Salamero, Jean; Usson, Yves; Werts, Martin; Beaurepaire, Emmanuel; Blanchoin, Laurent; Boltze, Frederic; Cavalli, Giacomo; Choquet, Daniel; Coppey, Maite; Dahan, Maxime; Dieterlen, Alain; Ducommun, Bernard; Favard, Cyril; Fort, Emmanuel; Gadal, Olivier; Heliot, Laurent; Hofflack, Bernard; Kervrann, Charles; Langowski, Jorg; LeBivic, Andre; Leveque-Fort, Sandrine; Matthews, Cedric; Monneret, Serge; Mordon, Serge; Mely, Yves

2012-12-01

Living material imaging, which is essential to medical diagnosis and therapy methods as well as fundamental and applied biology, is necessarily pluri-disciplinary, at the intersection of physics, (bio)chemistry and pharmacy, and requests mathematical and computer processing of signals and images. Image processing techniques may be applied at different levels (molecular, cellular or tissue level) or using various modes (optics, X rays, NMR, PET, US). This conference therefore presents recent methodological developments addressing the study of living material. The program of the conference started with a plenary session (multimode non linear microscopy of tissues and embryonary morphogenesis) followed by 6 sessions which titles are: (1) new microscopies applied to living materials), (2) agents for molecular and functional imaging), (3) recent developments in methodologies and instrumentations, (4) image processing methods and techniques, (5) image aided diagnosis, therapy and medical surveillance, (6) heterogenous data bases and distributed computations

Parameters for calculation of nuclear reactions of relevance to non-energy nuclear applications (Reference Input Parameter Library: Phase III). Summary report of the first research coordination meeting

International Nuclear Information System (INIS)

Capote Noy, R.

2004-08-01

A summary is given of the First Research Coordination Meeting on Parameters for Calculation of Nuclear Reactions of Relevance to Non-Energy Nuclear Applications (Reference Input Parameter Library: Phase III), including a critical review of the RIPL-2 file. The new library should serve as input for theoretical calculations of nuclear reaction data at incident energies up to 200 MeV, as needed for energy and non-energy modern applications of nuclear data. Technical discussions and the resulting work plan of the Coordinated Research Programme are summarized, along with actions and deadlines. Participants' contributions to the RCM are also attached. (author)

Summary final report: Contract between the Japan atomic power company and the U.S. Department of Energy Improvement of core safety - study on GEM (III)

International Nuclear Information System (INIS)

Burke, T.M.; Lucoff, D.M.

1997-01-01

This report provides a summary of activities associated with the technical exchange between representatives of the Japan Atomic Power Company (JAPC) and the United States Department of Energy (DOE) regarding the development and testing of Gas Expansion Modules (GEM) at the Fast Flux Test Facility (FFTF). Issuance of this report completes the scope of work defined in the original contract between JAPC and DOE titled ''Study on Improvement of Core Safety - Study on GEM (III).'' Negotiations related to potential modification of the contract are in progress. Under the proposed contract modification, DOE would provide an additional report documenting FFTF pump start tests with GEMs and answer additional JAPC questions related to core safety with and without GEMs

Chapter 5: Summary of model application

International Nuclear Information System (INIS)

1995-01-01

This chapter provides a brief summary of the model applications described in Volume III of the Final Report. This chapter dealt with the selected water management regimes; ground water flow regimes; agriculture; ground water quality; hydrodynamics, sediment transport and water quality in the Danube; hydrodynamics, sediment transport and water quality in the river branch system; hydrodynamics, sediment transport and water quality in the Hrusov reservoir and with ecology in this Danube area

Separation of 248Cm (III) from 252Cf (III) and its use in time resolved fluorescence spectroscopic (TRFS) studies

International Nuclear Information System (INIS)

Murali, M.S.; Nair, A.G.C.; Gujar, R.B.; Jain, A.; Tomar, B.S.; Godbole, S.V.; Reddy, A.V.R.; Manchanda, V.K.

2008-07-01

The present report gives a description of the methodology for the separation of 248 Cm(III) from decayed 252 Cf (III) waste solution. The waste solution was first assayed for 252 Cf content by neutron counting using a neutron well coincidence counter. The sample was subjected to the chemical separation of 248 Cm (III) from 252 Cf (III) following anion and cation exchange chromatography. The alpha spectrum of the separated curium fraction showed peaks due to 246 Cm and 248 Cm while the corresponding alpha spectrum of californium fraction showed 249,250,251,252 Cf. The gamma ray abundances of 249 Cf were determined with respect to its gamma rays of 387 keV and the data agreed well with that in literature. Separated Cm(III) was further characterized by recording its time resolved fluorescence spectrum (TRFS) in aqueous medium. (author)

Methodology of a systematic review.

Science.gov (United States)

Linares-Espinós, E; Hernández, V; Domínguez-Escrig, J L; Fernández-Pello, S; Hevia, V; Mayor, J; Padilla-Fernández, B; Ribal, M J

2018-05-03

The objective of evidence-based medicine is to employ the best scientific information available to apply to clinical practice. Understanding and interpreting the scientific evidence involves understanding the available levels of evidence, where systematic reviews and meta-analyses of clinical trials are at the top of the levels-of-evidence pyramid. The review process should be well developed and planned to reduce biases and eliminate irrelevant and low-quality studies. The steps for implementing a systematic review include (i) correctly formulating the clinical question to answer (PICO), (ii) developing a protocol (inclusion and exclusion criteria), (iii) performing a detailed and broad literature search and (iv) screening the abstracts of the studies identified in the search and subsequently of the selected complete texts (PRISMA). Once the studies have been selected, we need to (v) extract the necessary data into a form designed in the protocol to summarise the included studies, (vi) assess the biases of each study, identifying the quality of the available evidence, and (vii) develop tables and text that synthesise the evidence. A systematic review involves a critical and reproducible summary of the results of the available publications on a particular topic or clinical question. To improve scientific writing, the methodology is shown in a structured manner to implement a systematic review. Copyright © 2018 AEU. Publicado por Elsevier España, S.L.U. All rights reserved.

Summary statistics for end-point conditioned continuous-time Markov chains

DEFF Research Database (Denmark)

Hobolth, Asger; Jensen, Jens Ledet

Continuous-time Markov chains are a widely used modelling tool. Applications include DNA sequence evolution, ion channel gating behavior and mathematical finance. We consider the problem of calculating properties of summary statistics (e.g. mean time spent in a state, mean number of jumps between...... two states and the distribution of the total number of jumps) for discretely observed continuous time Markov chains. Three alternative methods for calculating properties of summary statistics are described and the pros and cons of the methods are discussed. The methods are based on (i) an eigenvalue...... decomposition of the rate matrix, (ii) the uniformization method, and (iii) integrals of matrix exponentials. In particular we develop a framework that allows for analyses of rather general summary statistics using the uniformization method....

EX1504L3 Water Column Summary Report and Profile Data Collection

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — A complete set of water column profile data and CTD Summary Report (if generated) generated by the Okeanos Explorer during EX1504L3: CAPSTONE Leg III: Main Hawaiian...

Summary final report: Contract between the Japan atomic power company and the U.S. Department of Energy Improvement of core safety - study on GEM (III)

Energy Technology Data Exchange (ETDEWEB)

Burke, T.M.; Lucoff, D.M.

1997-03-18

This report provides a summary of activities associated with the technical exchange between representatives of the Japan Atomic Power Company (JAPC) and the United States Department of Energy (DOE) regarding the development and testing of Gas Expansion Modules (GEM) at the Fast Flux Test Facility (FFTF). Issuance of this report completes the scope of work defined in the original contract between JAPC and DOE titled ''Study on Improvement of Core Safety - Study on GEM (III).'' Negotiations related to potential modification of the contract are in progress. Under the proposed contract modification, DOE would provide an additional report documenting FFTF pump start tests with GEMs and answer additional JAPC questions related to core safety with and without GEMs.

77 FR 19408 - Reinstate Index to Chapter III in 20 CFR

Science.gov (United States)

2012-03-30

... visit our Internet site, Social Security Online, at http://www.socialsecurity.gov . Correction In the... SOCIAL SECURITY ADMINISTRATION [Docket No. SSA-2012-0018] Reinstate Index to Chapter III in 20 CFR AGENCY: Social Security Administration. ACTION: Notice; correction. SUMMARY: The Social Security...

SG39 Deliverables. Summary of Methodology

International Nuclear Information System (INIS)

Yokoyama, Kenji

2015-01-01

For providing useful and physical feedback to nuclear data evaluators from cross section adjustment results, it is necessary to assess the reliability of the adjustment results. For instance, the adjustment results may include so-called 'compensation effects' which cause fictitious alterations of adjusted cross-sections by the cancellation of two or more reactions of cross sections. Typical compensation effects are possible in the following reactions: - Pu-239 fission spectrum and inelastic in general: Equivalent effect through neutron spectrum changes - Capture and (n,2n) for irradiation experiments: Same impact of disappearing the associated isotope - Capture and fission for spectral indices: e.g. U-238 capture (C28) and Pu-239 fission (F49) for C28/F49; Compensation between numerator and denominator - Many reactions for criticalities: Capture, fission, ν, χ, inelastic, elastic,... In addition, useless and unphysical systematic effects may occur in the cross section adjustments. To avoid the compensation effects and to point out systematic effects, several criteria with parameters/indices are recommended to use. This document summarizes the methodology with the definitions of the parameters/indices. Although a lot of parameters/indices are reported in the intermediate report of Subgroup 33, many institutions use their own different nomenclature to describe the parameters/indices about the cross section adjustment. Therefore, Subgroup 39 proposes a common nomenclature for convenience. (author)

Aircraft Battle Damage Assessment and Repair (ABDAR). Volume 1: Executive Summary

National Research Council Canada - National Science Library

Dierker, Ron

2000-01-01

.... This volume provides an executive summary and describes the overall program goals, the methodology used to develop the ABDAR technology and a demonstration system, and the results of a field test...

A performance assessment methodology for low-level waste facilities

International Nuclear Information System (INIS)

Kozak, M.W.; Chu, M.S.Y.; Mattingly, P.A.

1990-07-01

A performance assessment methodology has been developed for use by the US Nuclear Regulatory Commission in evaluating license applications for low-level waste disposal facilities. This report provides a summary of background reports on the development of the methodology and an overview of the models and codes selected for the methodology. The overview includes discussions of the philosophy and structure of the methodology and a sequential procedure for applying the methodology. Discussions are provided of models and associated assumptions that are appropriate for each phase of the methodology, the goals of each phase, data required to implement the models, significant sources of uncertainty associated with each phase, and the computer codes used to implement the appropriate models. In addition, a sample demonstration of the methodology is presented for a simple conceptual model. 64 refs., 12 figs., 15 tabs

The energy policy relevance of the 2014 IPCC Working Group III report on the macro-economics of mitigating climate change

International Nuclear Information System (INIS)

Rosen, Richard A.; Guenther, Edeltraud

2016-01-01

Research which attempted to determine the macroeconomic importance of mitigating climate change through 2100 was presented primarily in Chapter 6 of the 2014 IPCC Working Group III report. Some of the findings of this chapter were then summarized in the Summary for Policy Makers (SPMs) of both the Synthesis Report, and the WGIII report. Unfortunately, these SPMs omitted key aspects of what the overall macroeconomic results for the costs and benefits of mitigating climate change actually did and did not include, how they were produced, and a careful assessment of their uncertainty and scientific validity. Yet, many of the major omissions were acknowledged deep in the text of Chapter 6, but were not revealed to the public. We conclude, therefore, that neither of these SPMs was useful for energy policy makers and energy managers, and they were misleading due to their many key omissions. Finally, we recommend several improvements that can be made to integrated assessment modeling methodologies so that the macroeconomic analysis of mitigating climate change resulting from the use of such models can be more relevant and useful to energy policy makers in the future, and can be communicated to them better. - Highlights: •The 2014 IPCC Working Group III Report has major omissions in its economic analysis. •Many well-known benefits of mitigation are not included in its economic results. •The Summary for Policy Makers is not very useful for energy policy decision makers. •The upcoming Sixth IPCC WGIII analysis should be structured quite differently.

Generation of Natural-Language Textual Summaries from Longitudinal Clinical Records.

Science.gov (United States)

Goldstein, Ayelet; Shahar, Yuval

2015-01-01

Physicians are required to interpret, abstract and present in free-text large amounts of clinical data in their daily tasks. This is especially true for chronic-disease domains, but holds also in other clinical domains. We have recently developed a prototype system, CliniText, which, given a time-oriented clinical database, and appropriate formal abstraction and summarization knowledge, combines the computational mechanisms of knowledge-based temporal data abstraction, textual summarization, abduction, and natural-language generation techniques, to generate an intelligent textual summary of longitudinal clinical data. We demonstrate our methodology, and the feasibility of providing a free-text summary of longitudinal electronic patient records, by generating summaries in two very different domains - Diabetes Management and Cardiothoracic surgery. In particular, we explain the process of generating a discharge summary of a patient who had undergone a Coronary Artery Bypass Graft operation, and a brief summary of the treatment of a diabetes patient for five years.

Methodological issues in radiation dose-volume outcome analyses: Summary of a joint AAPM/NIH workshop

International Nuclear Information System (INIS)

Deasy, Joseph O.; Niemierko, Andrzej; Herbert, Donald; Yan, Di; Jackson, Andrew; Ten Haken, Randall K.; Langer, Mark; Sapareto, Steve

2002-01-01

This report represents a summary of presentations at a joint workshop of the National Institutes of Health and the American Association of Physicists in Medicine (AAPM). Current methodological issues in dose-volume modeling are addressed here from several different perspectives. Areas of emphasis include (a) basic modeling issues including the equivalent uniform dose framework and the bootstrap method, (b) issues in the valid use of statistics, including the need for meta-analysis, (c) issues in dealing with organ deformation and its effects on treatment response, (d) evidence for volume effects for rectal complications, (e) the use of volume effect data in liver and lung as a basis for dose escalation studies, and (f) implications of uncertainties in volume effect knowledge on optimized treatment planning. Taken together, these approaches to studying volume effects describe many implications for the development and use of this information in radiation oncology practice. Areas of significant interest for further research include the meta-analysis of clinical data; interinstitutional pooled data analyses of volume effects; analyses of the uncertainties in outcome prediction models, minimal parameter number outcome models for ranking treatment plans (e.g., equivalent uniform dose); incorporation of the effect of motion in the outcome prediction; dose-escalation/isorisk protocols based on outcome models; the use of functional imaging to study radio-response; and the need for further small animal tumor control probability/normal tissue complication probability studies

77 FR 18290 - Reinstate Index to Chapter III in 20 CFR

Science.gov (United States)

2012-03-27

...-800-325-0778, or visit our Internet site, Social Security Online, at http://www.socialsecurity.gov... SOCIAL SECURITY ADMINISTRATION [Docket No. SSA-2012-0018] Reinstate Index to Chapter III in 20 CFR AGENCY: Social Security Administration. ACTION: Notice. SUMMARY: At the request of the Office of the...

Summary of FY-1978 consultation input for Scenario Methodology Development

International Nuclear Information System (INIS)

Scott, B.L.; Benson, G.L.; Craig, R.A.; Harwell, M.A.

1979-11-01

The Scenario Methodology Development task is concerned with evaluating the geologic system surrounding an underground repository and describing the phenomena (volcanic, seismic, meteorite, hydrologic, tectonic, climate, etc.) which could perturb the system and possibly cause loss of repository integrity. This document includes 14 individual papers. Separate abstracts were prepared for all 14 papers

Subgroup on engineering needs: summary report

International Nuclear Information System (INIS)

Gupta, G.D.; Blass, J.; Coffin, L.F.; Cramer, B.A.; Hart, E.W.; McClintock, F.A.; Moon, D.M.; Richerson, D.

1979-01-01

The need to bridge the gap between academic knowledge and industrial application was generally agreed upon in the summary report. Five areas were identified in which future work needs to be performed. These areas refer to metallic as well as ceramic materials and include cumulative damage concepts for crack initiation, environmental studies, more realistic approaches to contitutive equations, design methodology, and fabrication problems in welding, casting, forging, machining, forming, coatings, and powder sintering

76 FR 34270 - Federal-State Extended Benefits Program-Methodology for Calculating “on” or “off” Total...

Science.gov (United States)

2011-06-13

... requirement. The Department plans to promulgate regulations about this methodology in the near future. In the...--Methodology for Calculating ``on'' or ``off'' Total Unemployment Rate Indicators for Purposes of Determining..., Labor. ACTION: Notice. SUMMARY: UIPL 16-11 informs states of the methodology used to calculate the ``on...

The steam generator programme of PISC III

International Nuclear Information System (INIS)

Birac, C.; Herkenrath, H.

1990-12-01

The PISC III Actions are intended to extend the results and methodologies of the previous PISC excercises, i.e. the validation of the capabilities of the various examination techniques when used on real defects in real components under real conditions of inspection. Being aware of the important safety role that steam generator tubes play as barrier between primary and secondary cooling system and of the industrial problems that the degradation of these tubes can create, the PISC III Management Board agreed to include in the PISC III Programme a special Action on Steam Generator Tubes Testing (SGT). It was decided to organize the programme in three phases, including Round Robin Tests (RRT): - capability tests on loose tubes, - capability tests on transportable mock-ups, - reliability tests on fixed mock-ups including some interesting SURRY tubes

International Working Group on Fast Reactors Eight Annual Meeting, Vienna, Austria, 15-18 April 1975. Summary Report. Part II

International Nuclear Information System (INIS)

1975-07-01

The Eighth Annual Meeting of the IAEA International Working Group on Past Reactors was held at the IAEA Headquarters in Vienna, Austria, from 15 to 18 April 1975. The Summary Report (Part I) contains the Minutes of the Meeting. The Summary Report (Part II) contains the papers which review the national programmes in the field of LMPBR’s and other presentations at the Meeting. The Summary Report (Part III) contains the discussions on the review of the national programmes

Advanced piloted aircraft flight control system design methodology. Volume 1: Knowledge base

Science.gov (United States)

Mcruer, Duane T.; Myers, Thomas T.

1988-01-01

The development of a comprehensive and electric methodology for conceptual and preliminary design of flight control systems is presented and illustrated. The methodology is focused on the design stages starting with the layout of system requirements and ending when some viable competing system architectures (feedback control structures) are defined. The approach is centered on the human pilot and the aircraft as both the sources of, and the keys to the solution of, many flight control problems. The methodology relies heavily on computational procedures which are highly interactive with the design engineer. To maximize effectiveness, these techniques, as selected and modified to be used together in the methodology, form a cadre of computational tools specifically tailored for integrated flight control system preliminary design purposes. While theory and associated computational means are an important aspect of the design methodology, the lore, knowledge and experience elements, which guide and govern applications are critical features. This material is presented as summary tables, outlines, recipes, empirical data, lists, etc., which encapsulate a great deal of expert knowledge. Much of this is presented in topical knowledge summaries which are attached as Supplements. The composite of the supplements and the main body elements constitutes a first cut at a a Mark 1 Knowledge Base for manned-aircraft flight control.

How to find out in radioisotope methodology

International Nuclear Information System (INIS)

Evers, C.

1976-01-01

The subject is dealt with in sections entitled: tracing books by topic; radioisotope methodology cross reference structure; finding a review; journals and how to trace journal articles; abstract; theses and dissertations; research and development reports; critical reviews and information summaries; data books; dictionaries and encyclopedias; guides to the literature; whom to contact; expert advice, research in progress, institutions. (U.K.)

A Narrative in Search of a Methodology.

Science.gov (United States)

Treloar, Anna; Stone, Teresa Elizabeth; McMillan, Margaret; Flakus, Kirstin

2015-07-01

Research papers present us with the summaries of scholars' work; what we readers do not see are the struggles behind the decision to choose one methodology over another. A student's mental health portfolio contained a narrative that led to an exploration of the most appropriate methodology for a projected study of clinical anecdotes told by nurses who work in mental health settings to undergraduates and new recruits about mental health nursing. This paper describes the process of struggle, beginning with the student's account, before posing a number of questions needing answers before the choice of the most appropriate methodology. We argue, after discussing the case for the use of literary analysis, discourse analysis, symbolic interactionism, hermeneutics, and narrative research, that case study research is the methodology of choice. Case study is frequently used in educational research and is sufficiently flexible to allow for an exploration of the phenomenon. © 2014 Wiley Periodicals, Inc.

A novel methodology for interpreting air quality measurements from urban streets using CFD modelling

Science.gov (United States)

Solazzo, Efisio; Vardoulakis, Sotiris; Cai, Xiaoming

2011-09-01

In this study, a novel computational fluid dynamics (CFD) based methodology has been developed to interpret long-term averaged measurements of pollutant concentrations collected at roadside locations. The methodology is applied to the analysis of pollutant dispersion in Stratford Road (SR), a busy street canyon in Birmingham (UK), where a one-year sampling campaign was carried out between August 2005 and July 2006. Firstly, a number of dispersion scenarios are defined by combining sets of synoptic wind velocity and direction. Assuming neutral atmospheric stability, CFD simulations are conducted for all the scenarios, by applying the standard k-ɛ turbulence model, with the aim of creating a database of normalised pollutant concentrations at specific locations within the street. Modelled concentration for all wind scenarios were compared with hourly observed NO x data. In order to compare with long-term averaged measurements, a weighted average of the CFD-calculated concentration fields was derived, with the weighting coefficients being proportional to the frequency of each scenario observed during the examined period (either monthly or annually). In summary the methodology consists of (i) identifying the main dispersion scenarios for the street based on wind speed and directions data, (ii) creating a database of CFD-calculated concentration fields for the identified dispersion scenarios, and (iii) combining the CFD results based on the frequency of occurrence of each dispersion scenario during the examined period. The methodology has been applied to calculate monthly and annually averaged benzene concentration at several locations within the street canyon so that a direct comparison with observations could be made. The results of this study indicate that, within the simplifying assumption of non-buoyant flow, CFD modelling can aid understanding of long-term air quality measurements, and help assessing the representativeness of monitoring locations for population

Nitrato-complexes of Y(III), La(III), Ce(III), Pr(III), Nd(III), Sm(III), Gd(III), Tb(III), Dy(III) and Ho(III) with 2-(2'-pyridyl) benzimidazole

Energy Technology Data Exchange (ETDEWEB)

Mishra, A; Singh, M P; Singh, V K

1982-05-01

The nitrato-complexes, (Y(PyBzH)/sub 2/(NO/sub 3/)/sub 2/)NO/sub 3/.H/sub 2/O and Nd, Sm, Gd, Tb, Dy, Ho ; n=1-3, m=0-0.5 ; PyBzh=2-(2 -pyridyl)benzimidazole) are formed on interaction of the ligand with metal nitrates in ethanol. The electrical conductance values (116-129 ohm/sup -1/cm/sup 2/mol/sup -1/) suggest 1:1 electrolyte-nature of the complexes. Magnetic moment values of Ce(2.53 B.M.), Pr(3.62 B.M.), Nd(3.52 B.M.), Sm(1.70 B.M.), Gd(8.06 B.M.), Tb(9.44 B.M.), Dy(10.56 B.M.) and Ho(10.51 B.M.) in the complexes confirm the positive state of the metals. Infrared evidences are obtained for the existance of both coordinated (C/sub 2/v) and uncoordinated (D/sub 3/h) nitrate groups. Electronic absorption spectra of Pr(III)-, Nd(III)-, Sm(III)-, Tb(III)-, Dy(III)- and Ho(III)-complexes have been analysed in the light of LSJ terms.

Nitrato-complexes of Y(III), La(III), Ce(III), Pr(III), Nd(III), Sm(III), Gd(III), Tb(III), Dy(III) and Ho(III) with 2-(2'-pyridyl) benzimidazole

International Nuclear Information System (INIS)

Mishra, A.; Singh, M.P.; Singh, V.K.

1982-01-01

The nitrato-complexes, [Y(PyBzH) 2 (NO 3 ) 2 ]NO 3 .H 2 O and Nd, Sm, Gd, Tb, Dy, Ho ; n=1-3, m=0-0.5 ; PyBzh=2-(2 -pyridyl)benzimidazole] are formed on interaction of the ligand with metal nitrates in ethanol. The electrical conductance values (116-129 ohm -1 cm 2 mol -1 ) suggest 1:1 electrolyte-nature of the complexes. Magnetic moment values of Ce(2.53 B.M.), Pr(3.62 B.M.), Nd(3.52 B.M.), Sm(1.70 B.M.), Gd(8.06 B.M.), Tb(9.44 B.M.), Dy(10.56 B.M.) and Ho(10.51 B.M.) in the complexes confirm the terpositive state of the metals. Infrared evidences are obtained for the existance of both coordinated (C 2 v) and uncoordinated (D 3 h) nitrate groups. Electronic absorption spectra of Pr(III)-, Nd(III)-, Sm(III)-, Tb(III)-, Dy(III)- and Ho(III)-complexes have been analysed in the light of LSJ terms. (author)

Voltammetric method to determine chromium (III) in potable water at level of ultra plans

International Nuclear Information System (INIS)

Jimenez B, Irene; Alvarado G, Ana L.

2004-01-01

It was established an analytical methodology to determine Cr (III) in drinking water using a voltammetric technique of Differential Pulse Cathodic Stripping Voltammetry with an Adsorptive Preconcentration of a complex Cr(III)-diethiltriaminpentaceticacid (Cr-DTPA) in a mercury drop. A dissolution of sodium nitrate was used as a supporting electrolyte. The optimized voltammetric parameters were: adsorption time, scan rate, absorption potential, p H, complex agent and sodium nitrate concentration. The linear range of the methodology is between 20 ng/L and 60 ng/L and the detection and quantification limits are 13 ng/L and 20 ng/L respectively. (Author) [es

Application of project management in technology improvement of Qinshan III

International Nuclear Information System (INIS)

Liu Xiaonian

2008-01-01

During the operation of Qinshan III, many engineering modifications and renovation projects are being carried out. Advanced international project management methodologies accustomed to the policy and organizational characteristics of TQNPC were applied to the management of these projects. After practical application and development of these methodologies, the company finally sets up its own classification of project management system. The project management system is introduced and discussed for its evolving direction in this paper. (authors)

Cloud point extraction: an alternative to traditional liquid-liquid extraction for lanthanides(III) separation.

Science.gov (United States)

Favre-Réguillon, Alain; Draye, Micheline; Lebuzit, Gérard; Thomas, Sylvie; Foos, Jacques; Cote, Gérard; Guy, Alain

2004-06-17

Cloud point extraction (CPE) was used to extract and separate lanthanum(III) and gadolinium(III) nitrate from an aqueous solution. The methodology used is based on the formation of lanthanide(III)-8-hydroxyquinoline (8-HQ) complexes soluble in a micellar phase of non-ionic surfactant. The lanthanide(III) complexes are then extracted into the surfactant-rich phase at a temperature above the cloud point temperature (CPT). The structure of the non-ionic surfactant, and the chelating agent-metal molar ratio are identified as factors determining the extraction efficiency and selectivity. In an aqueous solution containing equimolar concentrations of La(III) and Gd(III), extraction efficiency for Gd(III) can reach 96% with a Gd(III)/La(III) selectivity higher than 30 using Triton X-114. Under those conditions, a Gd(III) decontamination factor of 50 is obtained.

Overview of a performance assessment methodology for low-level radioactive waste disposal facilities

International Nuclear Information System (INIS)

Kozak, M.W.; Chu, M.S.Y.

1991-01-01

A performance assessment methodology has been developed for use by the US Nuclear Regulatory Commission in evaluating license applications for low-level waste disposal facilities. This paper provides a summary and an overview of the modeling approaches selected for the methodology. The overview includes discussions of the philosophy and structure of the methodology. This performance assessment methodology is designed to provide the NRC with a tool for performing confirmatory analyses in support of license reviews related to postclosure performance. The methodology allows analyses of dose to individuals from off-site releases under normal conditions as well as on-site doses to inadvertent intruders. 24 refs., 1 tab

Round robin tests of the PISC III programme on defective steam generators tubes

International Nuclear Information System (INIS)

Birac, C.; Herkenrath, H.; Crutzen, S.; Miyake, Y.; Maciga, G.

1991-11-01

The PISC III actions are intended to extend the results and methodologies of the previous PISC exercises, i.e. the assessment of the capabilities of the various examination techniques when used on real or realistic flaws in real components under real conditions of inspection. Being aware of the industrial problems that the degradation of steam generator tubes can create, the PISC III management board decided to include in the PISC III programme a special action on steam generator tubes testing (SGT). (author)

Nuclear EGFRvIII resists hypoxic microenvironment induced apoptosis via recruiting ERK1/2 nuclear translocation

Energy Technology Data Exchange (ETDEWEB)

Xie, Hui; Yang, Jinfeng; Xing, Wenjing; Dong, Yucui [Dept. of Immunology, Harbin Medical University, Harbin 150081 (China); Key Lab Infection & Immunity, Heilongjiang Province, Harbin 150081 (China); Ren, Huan, E-mail: renhuan@ems.hrbmu.edu.cn [Dept. of Immunology, Harbin Medical University, Harbin 150081 (China); Key Lab Infection & Immunity, Heilongjiang Province, Harbin 150081 (China)

2016-02-05

Glioblastoma (GBM) is the most aggressive type of primary brain tumor. Its interaction with the tumor microenvironment promotes tumor progression. Furthermore, GBM bearing expression of EGFRvIII displays more adaptation to tumor microenvironment related stress. But the mechanisms were poorly understood. Here, we presented evidence that in the human U87MG glioblastoma tumor model, EGFRvIII overexpression led aberrant kinase activation and nuclear translocation of EGFRvIII/ERK1/2 under hypoxia, which induced growth advantage by resisting apoptosis. Additionally, EGFRvIII defective in nuclear entry impaired this capacity in hypoxia adaptation, and partially interrupted ERK1/2 nuclear translocation. Pharmacology or genetic interference ERK1/2 decreased hypoxia resistance triggered by EGFRvIII expression, but not EGFRvIII nuclear translocation. In summary, this study identified a novel role for EGFRvIII in hypoxia tolerance, supporting an important link between hypoxia and subcellular localization alterations of the receptor. - Highlights: • Nuclear translocation of EGFRvIII contributes to GBM cell apoptotic resistance by hypoxia. • Nuclear ERK1/2 facilitates EGFRvIII in hypoxia resistance. • EGFRvIII nuclear translocation is not dependent on ERK1/2.

Eighth annual meeting, Vienna, Austria, 15-18 April 1975. Summary report. Part III

International Nuclear Information System (INIS)

1976-01-01

The Summary Report of the Eighth Annual Meeting of the International Working Group on Fast Reactors contains the minutes of the meeting (Part 1); papers which review the national programmes in the field of LMFBRs (Part 2) and the discussions on the review of national programmes (Part 3). The agenda of the meeting involved design, construction, operating experiences of demonstration fast power reactors, reprocessing of spent fuel from LMFBRs, reliability of decay heat removal systems, fuel failure mechanisms, safety of LMFBRs

Eighth annual meeting, Vienna, Austria, 15-18 April 1975. Summary report. Part III

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-01-01

The Summary Report of the Eighth Annual Meeting of the International Working Group on Fast Reactors contains the minutes of the meeting (Part 1); papers which review the national programmes in the field of LMFBRs (Part 2) and the discussions on the review of national programmes (Part 3). The agenda of the meeting involved design, construction, operating experiences of demonstration fast power reactors, reprocessing of spent fuel from LMFBRs, reliability of decay heat removal systems, fuel failure mechanisms, safety of LMFBRs.

I. DEVELOPMENTAL METHODOLOGY AS A CENTRAL SUBDISCIPLINE OF DEVELOPMENTAL SCIENCE.

Science.gov (United States)

Card, Noel A

2017-06-01

This first chapter introduces the main goals of the monograph and previews the remaining chapters. The goals of this monograph are to provide summaries of our current understanding of advanced developmental methodologies, provide information that can advance our understanding of human development, identify shortcomings in our understanding of developmental methodology, and serve as a flagpost for organizing developmental methodology as a subdiscipline within the broader field of developmental science. The remaining chapters in this monograph address issues in design (sampling and big data), longitudinal data analysis, and issues of replication and research accumulation. The final chapter describes the history of developmental methodology, considers how the previous chapters in this monograph fit within this subdiscipline, and offers recommendations for further advancement. © 2017 The Society for Research in Child Development, Inc.

Washington International Renewable Energy Conference (WIREC) 2008 Pledges. Methodology and Assumptions Summary

Energy Technology Data Exchange (ETDEWEB)

Babiuch, Bill [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bilello, Daniel E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Cowlin, Shannon C. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mann, Margaret [National Renewable Energy Lab. (NREL), Golden, CO (United States); Wise, Alison [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2008-08-01

This report describes the methodology and assumptions used by NREL in quantifying the potential CO2 reductions resulting from more than 140 governments, international organizations, and private-sector representatives pledging to advance the uptake of renewable energy.

BALTICA III. Plant condition and life management

International Nuclear Information System (INIS)

Hietanen, S.; Auerkari, P.

1995-01-01

The BALTICA III, International Conference on Plant Condition and Life Management was held on June 6 - 8, 1995 on board Silja Serenade on its cruise between Helsinki - Stockholm and at the Forest Lake Hotel Korpilampi in Espoo. BALTICA III provides forum for the transfer of technology from applied research to practise. This is the second volume of the publications, which contain the presentations given at the BALTICA III, Plant Condition and Life Management. A total of 45 articles report recent experience in plant condition and life management. The conference focuses on recent applications that have been demonstrated for the benefit of safe and economical operation of power plants. Practical approach is emphasised, including the presentations that aim to provide insight into new techniques, improvements in assessment methodologies as well as maintenance strategies. Compared to earlier occasions in the BALTICA series, a new aspect is in the applications of knowledge-based systems in the service of power plant life management. (orig.)

Eleventh annual meeting, Bologna, Italy, 17-20 April 1978. Summary report. Part I

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-06-01

The Summary Report of the Eleventh Annual Meeting of the IAEA International Working Group on Fast Reactors contains the Minutes of the Meeting (Part I); the papers which review the national programmes in the field of LMFBRs and other presentations at the Meeting (Part II); and the discussions on the review of the national programmes (Part III)

Design methodology of Dutch banknotes

Science.gov (United States)

de Heij, Hans A. M.

2000-04-01

Since the introduction of a design methodology for Dutch banknotes, the quality of Dutch paper currency has improved in more than one way. The methodology is question provides for (i) a design policy, which helps fix clear objectives; (ii) design management, to ensure a smooth cooperation between the graphic designer, printer, papermaker an central bank, (iii) a program of requirements, a banknote development guideline for all parties involved. This systematic approach enables an objective selection of design proposals, including security features. Furthermore, the project manager obtains regular feedback from the public by conducting market surveys. Each new design of a Netherlands Guilder banknote issued by the Nederlandsche Bank of the past 50 years has been an improvement on its predecessor in terms of value recognition, security and durability.

Goals and Methodology for a Surgery Residency Program: A Committee Approach.

Science.gov (United States)

Knecht, Charles D.; And Others

1979-01-01

Written goals of a small animal residency program established by Purdue University are identified and an elaborate list of methodology for goals is provided. Tables include: summary of required activities of residents, checklist of residency progress, and comparable effort for surgery residency and masters program. (Author/MLW)

Peabody Picture Vocabulary Test (PPVT-III: Psychometric properties and significance for application

Directory of Open Access Journals (Sweden)

Nataša Bucik

2003-12-01

Full Text Available The purpose of this article is to present the content, conceptual structure and methodological steps of the latest revision of the Peabody Picture Vocabulary Test (PPVT-III, which is a highly functional and valuable vocabulary test that has been in use since 1959 in different language and cultural surroundings. On the case of the PPVT-III we are presenting the procedure of development and standardization of such vocabulary tests as well as its translation and adaptation from one language and cultural milieu to another. We also note the practical use of the PPVT-III for research purposes. In Slovenian language no vocabulary tests were developed or adapted so far; PPVT-III is presented in this context, too.

Case Study Research Methodology

Directory of Open Access Journals (Sweden)

Mark Widdowson

2011-01-01

Full Text Available Commenting on the lack of case studies published in modern psychotherapy publications, the author reviews the strengths of case study methodology and responds to common criticisms, before providing a summary of types of case studies including clinical, experimental and naturalistic. Suggestions are included for developing systematic case studies and brief descriptions are given of a range of research resources relating to outcome and process measures. Examples of a pragmatic case study design and a hermeneutic single-case efficacy design are given and the paper concludes with some ethical considerations and an exhortation to the TA community to engage more widely in case study research.

OpenKnowledge Deliverable 3.3.: A methodology for ontology matching quality evaluation

OpenAIRE

Yatskevich, Mikalai; Giunchiglia, Fausto; McNeill, Fiona; Shvaiko, Pavel

2007-01-01

This document presents an evaluation methodology for the assessment of quality results produced by ontology matchers. In particular, it discusses: (i) several standard quality measures used in the ontology matching evaluation, (ii) a methodology of how to build semiautomatically an incomplete reference alignment allowing for the assessment of quality results produced by ontology matchers and (iii) a preliminary empirical evaluation of the OpenKnowledge ontology matching component.

Improved Security Models & Protocols in Online Mobile Business Financial Transactions

OpenAIRE

Sreeramana Aithal

2017-01-01

Chapter I : Introduction to Mobile Business and Mobile Banking Chapter II : Review of Literature on Mobile Business Technology, Mobile Banking Services & Security Chapter III : Research Objectives and Methodology Chapter IV : Results and Discussion Chapter V : Summary and Conclusions Bibliography

Tenth annual meeting, Vienna, Austria, 29 March - 1 April 1977. Summary report. Part I

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-05-01

The Summary Report of Tenth Annual Meeting of the IAEA International Working Group on Fast Reactors contains the Minutes of the Meeting (Part I); the papers which review the national programmes in the field of LMFBRs and other presentations at the Meeting (Part II); and the discussions on the review of the national programmes (Part III)

Mergeable summaries

DEFF Research Database (Denmark)

Agarwal, Pankaj K.; Graham, Graham; Huang, Zengfeng

2013-01-01

We study the mergeability of data summaries. Informally speaking, mergeability requires that, given two summaries on two datasets, there is a way to merge the two summaries into a single summary on the two datasets combined together, while preserving the error and size guarantees. This property m...

Research in collegiate mathematics education III

CERN Document Server

Arcavi, A; Kaput, Jim; Dubinsky, Ed; Dick, Thomas

1998-01-01

Volume III of Research in Collegiate Mathematics Education (RCME) presents state-of-the-art research on understanding, teaching, and learning mathematics at the post-secondary level. This volume contains information on methodology and research concentrating on these areas of student learning: Problem solving. Included here are three different articles analyzing aspects of Schoenfeld's undergraduate problem-solving instruction. The articles provide new detail and insight on a well-known and widely discussed course taught by Schoenfeld for many years. Understanding concepts. These articles fe

Methodology for building confidence measures

Science.gov (United States)

Bramson, Aaron L.

2004-04-01

This paper presents a generalized methodology for propagating known or estimated levels of individual source document truth reliability to determine the confidence level of a combined output. Initial document certainty levels are augmented by (i) combining the reliability measures of multiply sources, (ii) incorporating the truth reinforcement of related elements, and (iii) incorporating the importance of the individual elements for determining the probability of truth for the whole. The result is a measure of confidence in system output based on the establishing of links among the truth values of inputs. This methodology was developed for application to a multi-component situation awareness tool under development at the Air Force Research Laboratory in Rome, New York. Determining how improvements in data quality and the variety of documents collected affect the probability of a correct situational detection helps optimize the performance of the tool overall.

Two-phase titration of cerium(III) by permanganate

International Nuclear Information System (INIS)

Lazarev, A.I.; Lazareva, V.I.; Gerko, V.V.

1987-01-01

This paper presents a method for the two-phase titrimetric determination of cerium(III) with permanganate which does not require an expenditure of sugar and preliminary removal of chlorides and nitrates. The interaction of cerium(III) with permanganate at room temperature was studied as a function of the pH, the concentration of pyrophosphate, tetraphenylphosphonium (TPP), permanganate, and extraneous compounds, the rate of titration, and the time of stay of the solution in air before titration. The investigations were conducted according to the following methodology: water, solution of cerium(III) pyrophosphate, and TPP were introduced into an Erlenmeyer flask with a side branch near the bottom for clearer observation of the color of the chloroform phase. The authors established the given pH value, poured the water into a volume of 50 ml, and added chloroform. The result was titrated with permanganate solutions of various concentrations until a violet color appeared in the chloroform phase

Isothiocyanato complexes of Gd(III), Tb(III), Dy(III) and Ho(III) with 2-(2'-pyridyl)benzimidazole

Energy Technology Data Exchange (ETDEWEB)

Mishra, A; Singh, V K

1982-01-01

Six-coordinated complexes of the type (Ln(PyBzH)/sub 2/NCS.H/sub 2/O) (NCS)/sub 2/.nH/sub 2/O/mC/sub 2/H/sub 5/OH (Ln = Gd(III), Tb(III), Dy(III) and Ho(III), n=1-2; m=1) have been prepared from Ln(NCS)/sub 6//sup 3 -/. The room temperature magnetic moment values confirm the terpositive state of the lanthanide ions. Infrared spectra suggest the N-coordination of thiocyanate group. Electronic spectral studies of Tb(III), Dy(III) and Ho(III) complexes have been made in terms of LSJ term energies. 13 refs.

Conceptual design summary for modifying Doublet III to a large dee-shaped configuration

International Nuclear Information System (INIS)

Davis, L.G.; Gallix, R.; Luxon, J.L.; Mahdavi, M.A.; Puhn, F.A.; Rock, P.J.; Wesley, J.C.

1983-05-01

The Doublet III tokamak is to be reconfigured by replacing its indented (doublet) vacuum vessel with a larger one of a dee-shaped cross section. This change will permit significantly larger elongated plasmas than is presently possible and will allow higher plasma current (up to 5 MA) and anticipated longer confinement time. Reactor relevant values of stable beta and plasma pressure are predicted. This modification, while resulting in a significant change in capability, utilizes most of the existing coils, structure, systems and facility

Complexation of trivalent actinides and lanthanides with hydrophilic N-donor ligands for Am(III)/Cm(III) and An(III)/Ln(III) separation; Komplexierung von trivalenten Actiniden und Lanthaniden mit hydrophilen N-Donorliganden zur Am(III)/Cm(III)- bzw. An(III)/Ln(III)-Trennung

Energy Technology Data Exchange (ETDEWEB)

Wagner, Christoph

2017-07-24

The implementation of actinide recycling processes is considered in several countries, aiming at the reduction of long-term radiotoxicity and heat load of used nuclear fuel. This requires the separation of the actinides from the fission and corrosion products. The separation of the trivalent actinides (An(III)) Am(III) and Cm(III), however, is complicated by the presence of the chemically similar fission lanthanides (Ln(III)). Hydrophilic N-donor ligands are employed as An(III) or Am(III) selective complexing agents in solvent extraction to strip An(III) or Am(III) from an organic phase loaded with An(III) and Ln(III). Though they exhibit excellent selectivity, the complexation chemistry of these ligands and the complexes formed during solvent extraction are not sufficiently characterized. In the present thesis the complexation of An(III) and Ln(III) with hydrophilic N-donor ligands is studied by time resolved laser fluorescence spectroscopy (TRLFS), UV/Vis, vibronic sideband spectroscopy and solvent extraction. TRLFS studies on the complexation of Cm(III) and Eu(III) with the Am(III) selective complexing agent SO{sub 3}-Ph-BTBP (tetrasodium 3,3{sup '},3'',3{sup '''}-([2,2{sup '}-bipyridine]-6,6{sup '}-diylbis(1,2,4-triazine-3,5,6-triyl)) tetrabenzenesulfonate) revealed the formation of [M(SO{sub 3}-Ph-BTBP){sub n}]{sup (4n-3)-} complexes (M = Cm(III), Eu(III); n = 1, 2). The conditional stability constants were determined in different media yielding two orders of magnitude larger β{sub 2}-values for the Cm(III) complexes, independently from the applied medium. A strong impact of ionic strength on the stability and stoichiometry of the formed complexes was identified, resulting from the stabilization of the pentaanionic [M(SO{sub 3}-Ph-BTBP){sub 2}]{sup 5-} complex with increasing ionic strength. Thermodynamic studies of Cm(III)-SO{sub 3}-Ph-BTBP complexation showed that the proton concentration of the applied medium impacts

A solar reserve methodology for renewable energy integration studies based on sub-hourly variability analysis

Energy Technology Data Exchange (ETDEWEB)

Ibanez, Eduardo; Brinkman, Gregory; Hummon, Marissa [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lew, Debra

2012-07-01

Increasing penetration of wind and solar energy are raising concerns among electric system operators because of the variability and uncertainty associated with the power sources. Previous work focused on the quantification of reserves for systems with wind power. This paper presents a new methodology that allows the determination of necessary reserves for high penetrations of photovoltaic power and compares it to the wind-based methodology. The solar reserve methodology was applied to Phase 2 of the Western Wind and Solar Integration Study. A summary of the results is included. (orig.)

Methodology for assessment of safety risk due to potential accidents in US gaseous diffusion plants

International Nuclear Information System (INIS)

Turner, J.H.; O'Kain, D.U.

1991-01-01

Gaseous diffusion plants that operate in the United States represent a unique combination of nuclear and chemical hazards. Assessing and controlling the health, safety, and environmental risks that can result from natural phenomena events, process upset conditions, and operator errors require a unique methodology. Such a methodology has been developed for the diffusion plants and is being utilized to assess and control the risk of operating the plants. A summary of the methodology developed to assess the unique safety risks at the US gaseous diffusion plants is presented in this paper

Synthesis and characterization of Fe(III-piperazine-derived complexes encapsulated in zeolite Y

Directory of Open Access Journals (Sweden)

Márcio E. Berezuk

2012-01-01

Full Text Available Zeolite-encapsulated complexes have been widely applied in hydrocarbon oxidation catalysis. The "ship-in-a-bottle" encapsulation of iron(III complexes containing piperazine and piperazine-derivative ligands in zeolite-Y is described. The flexible ligand methodology was employed and the efficiency and reproducibility of the procedure was investigated. The catalysts were characterized employing several techniques and the results indicate the presence of coordinated and uncoordinated iron(III ions inside and outside the zeolitic cage.

75 FR 71648 - Federal Motor Vehicle Safety Standards, Child Restraint Systems; Hybrid III 10-Year-Old Child...

Science.gov (United States)

2010-11-24

... No. NHTSA-2010-0158 Regulation Identifier No. (RIN) 2127-AJ44 Federal Motor Vehicle Safety Standards, Child Restraint Systems; Hybrid III 10-Year-Old Child Test Dummy AGENCY: National Highway Traffic Safety... (SNPRM). SUMMARY: This document proposes to amend Federal Motor Vehicle Safety Standard (FMVSS) No. 213...

Complexes of 4-chlorophenoxyacetates of Nd(III), Gd(III) and Ho(III)

International Nuclear Information System (INIS)

Ferenc, W.; Bernat, M; Gluchowska, H.W.; Sarzynski, J.

2010-01-01

The complexes of 4-chlorophenoxyacetates of Nd(III), Gd(III) and Ho(III) have been synthesized as polycrystalline hydrated solids, and characterized by elemental analysis, spectroscopy, magnetic studies and also by X-ray diffraction and thermogravimetric measurements. The analysed complexes have the following colours: violet for Nd(III), white for Gd(III) and cream for Ho(III) compounds. The carboxylate groups bind as bidentate chelating (Ho) or bridging ligands (Nd, Gd). On heating to 1173K in air the complexes decompose in several steps. At first, they dehydrate in one step to form anhydrous salts, that next decompose to the oxides of respective metals. The gaseous products of their thermal decomposition in nitrogen were also determined and the magnetic susceptibilities were measured over the temperature range of 76-303K and the magnetic moments were calculated. The results show that 4-chlorophenoxyacetates of Nd(III), Gd(III) and Ho(III) are high-spin complexes with weak ligand fields. The solubility value in water at 293K for analysed 4-chlorophenoxyacetates is in the order of 10 -4 mol/dm 3 . (author)

SKI SITE-94, deep repository performance assessment project, summary

International Nuclear Information System (INIS)

1999-01-01

SITE-94 is a comprehensive performance assessment exercise for a hypothetical repository for spent nuclear fuel at a real site in Sweden. SITE-94 was carried out to develop the capability and tools to enable Swedish Nuclear Power Inspectorate (SKI) to review fully the proposals for a deep repository which are expected to be made by the Swedish Nuclear Fuel and Waste Management Company, SKB (the implementor). Sweden is one of the leading countries in the research and development of geological disposal of radioactive waste. The developed methodology for performance assessment has attracted interests from other countries. The Summary of the main report of the SITE-94 project is translated here into Japanese to allow to make the information on the methodology and the related issues available among Japanese concerned. (author)

Formation constants of Sm(III), Dy(III), Gd(III), Pr(III) and Nd(III) complexes of tridentate schiff base, 2-[(1H-benzimidazol-2-yl-methylene) amino] phenol

International Nuclear Information System (INIS)

Omprakash, K.L.; Chandra Pal, A.V.; Reddy, M.L.N.

1982-01-01

A new tridentate schiff base, 2- (1H-benzimidazol-2-yl-methylene)amino phenol derived from benzimididazole-2-carbo-xaldehyde and 2-aminophenol has been synthesised and characterised by spectral and analytical data. Proton-ligand formation constants of the schiff base and metal-ligand formation constants of its complexes with Sm(III), Dy(III), Gd(III), Nd(III) and Pr(III) have been determined potentiometrically in 50% (v/v) aqueous dioxane at an ionic strength of 0.1M (NaClO 4 ) and at 25deg C using the Irving-Rossotti titration technique. The order of stability constants (logβ 2 ) is found to be Sm(III)>Dy(III)>Gd(III)>Pr(III)>Nd(III). (author)

Formation constants of Sm(III), Dy(III), Gd(III), Pr(III) and Nd(III) complexes of tridentate schiff base, 2-((1H-benzimidazol-2-yl-methylene) amino) phenol

Energy Technology Data Exchange (ETDEWEB)

Omprakash, K L; Chandra Pal, A V; Reddy, M L.N. [Osmania Univ., Hyderabad (India). Dept. of Chemistry

1982-03-01

A new tridentate schiff base, 2- (1H-benzimidazol-2-yl-methylene)amino phenol derived from benzimididazole-2-carbo-xaldehyde and 2-aminophenol has been synthesised and characterised by spectral and analytical data. Proton-ligand formation constants of the schiff base and metal-ligand formation constants of its complexes with Sm(III), Dy(III), Gd(III), Nd(III) and Pr(III) have been determined potentiometrically in 50% (v/v) aqueous dioxane at an ionic strength of 0.1M (NaClO/sub 4/) and at 25deg C using the Irving-Rossotti titration technique. The order of stability constants (log..beta../sub 2/) is found to be Sm(III)>Dy(III)>Gd(III)>Pr(III)>Nd(III).

76 FR 54216 - Pacific Fishery Management Council (Council); Work Session To Review Proposed Salmon Methodology...

Science.gov (United States)

2011-08-31

... Fishery Management Council (Council); Work Session To Review Proposed Salmon Methodology Changes AGENCY.... ACTION: Notice of a public meeting. SUMMARY: The Pacific Fishery Management Council's Salmon Technical Team (STT), Scientific and Statistical Committee (SSC) Salmon Subcommittee, and Model Evaluation...

Spectrophotometric and pH-Metric Studies of Ce(III, Dy(III, Gd(III,Yb(III and Pr(III Metal Complexes with Rifampicin

Directory of Open Access Journals (Sweden)

A. N. Sonar

2011-01-01

Full Text Available The metal-ligand and proton-ligand stability constant of Ce(III, Dy(III, Gd(III,Yb(III and Pr(III metals with substituted heterocyclic drug (Rifampicin were determined at various ionic strength by pH metric titration. NaClO4 was used to maintain ionic strength of solution. The results obtained were extrapolated to the zero ionic strength using an equation with one individual parameter. The thermodynamic stability constant of the complexes were also calculated. The formation of complexes has been studied by Job’s method. The results obtained were of stability constants by pH metric method is confirmed by Job’s method.

Complexes of lanthanum(III), cerium(III), samarium(III) and dysprosium(III) with substituted piperidines

Energy Technology Data Exchange (ETDEWEB)

Manhas, B S; Trikha, A K; Singh, H; Chander, M

1983-11-01

Complexes of the general formulae M/sub 2/Cl/sub 6/(L)/sub 3/.C/sub 2/H/sub 5/OH and M/sub 2/(NO/sub 3/)/sub 6/(L)/sub 2/.CH/sub 3/OH have been synthesised by the reactions of chlorides and nitrates of La(III), Ce(III), Sm(III) and Dy(III) with 2-methylpiperidine, 3-methylpiperidine and 4-methylpiperidine. These complexes have been characterised on the basis of their elemental analysis, and IR and electronic reflectance spectra. IR spectral data indicate the presence of coordinated ethanol and methanol molecules and bidentate nitrate groups. Coordination numbers of the metal ions vary from 5 to 8. 19 refs.

77 FR 70451 - Proposed Collection; Comment Request; Methodological Studies for the Population Assessment of...

Science.gov (United States)

2012-11-26

... are no capital, operating or maintenance costs. Table 1--Estimated Annual Reporting Burden Summary... Collection: Title: Methodological Studies for Population Assessment of Tobacco and Health (PATH) Study. Type... concurrent basis]. Affected Public: Individuals. Type of Respondents: Youth (ages 12-17) and Adults (ages 18...

Ecological impact study methodology for hydrotechnical projects

International Nuclear Information System (INIS)

Manoliu, Mihai; Toculescu, Razvan

1993-01-01

Besides the expected benefits, hydrotechnical projects may entail unfavorable effects on the hydrological regime, environment, health and living conditions of the population. Rational water resource management should take into consideration both the favorable and unfavorable effects. This implies the assessment of socio-economic and environmental impacts of the changes of the hydrological regime. The paper proposes a methodology for carrying out impact studies of hydrotechnical projects. The results of the work are presented graphically on the basis of composite programing. A summary of mathematical methods involved in impact study design is also presented. (authors)

Inner-sphere and outer-sphere complexes of yttrium(III), lanthanum (III), neodymium(III), terbium(III) and thulium(III) with halide ions in N,N-dimethylformamide

International Nuclear Information System (INIS)

Takahashi, Ryouta; Ishiguro, Shin-ichi

1991-01-01

The formation of chloro, bromo and iodo complexes of yttrium(III), and bromo and iodo complexes of lanthanum(III), neodymium(III), terbium(III) and thulium(III) has been studied by precise titration calorimetry in N,N-dimethylformamide (DMF) at 25 o C. The formation of [YCl] 2+ , [YCl 2 ] + , [YCl 3 ] and [YCl 4 ] - , and [MBr] 2+ and [MBr 2 ] + (M = Y, La, Nd, Tb, Tm) was revealed, and their formation constants, enthalpies and entropies were determined. It is found that the formation enthalpies change in the sequence ΔH o (Cl) > ΔH o (l), which is unusual for hard metal (III) ions. This implies that, unlike the chloride ion, the bromide ion forms outer-sphere complexes with the lanthanide(III) and yttrium(III) ions in DMF. Evidence for either an inner- or outer-sphere complex was obtained from 89 Y NMR spectra for Y(ClO 4 ) 3 , YCl 3 and YBr 3 DMF solutions at room temperature. (author)

Gradual linguistic summaries

NARCIS (Netherlands)

Wilbik, A.M.; Kaymak, U.; Laurent, A.; Strauss, O.; Bouchon-Meunier, xx

2014-01-01

In this paper we propose a new type of protoform-based linguistic summary – the gradual summary. This new type of summaries aims in capturing the change over some time span. Such summaries can be useful in many domains, for instance in economics, e.g., "prices of X are getting smaller" in eldercare,

LANGUAGE LABORATORY SPECIFICATIONS. A PROCUREMENT GUIDE FOR THE PURCHASE OF LANGUAGE LABORATORY INSTALLATIONS IN WISCONSIN, NDEA, TITLE III.

Science.gov (United States)

GRITTNER, FRANK; PAVLAT, RUSSELL

THE KNOWLEDGE ACCUMULATED FROM THE EXPERIENCE OF INSTALLING MANY LANGUAGE LABORATORIES UNDER THE TITLE III, NDEA PROGRAM FORMS THE BASIS FOR THE GUIDELINES PRESENTED IN THIS BULLETIN. THE DOCUMENT INCLUDES A SUMMARY OF CONDITIONS DESIRABLE PRIOR TO THE PURCHASE OF A LABORATORY, SAMPLE SPECIFICATIONS FOR EACH COMPONENT OF THE LAB, SPECIFICATIONS…

Estimating Effect Sizes and Expected Replication Probabilities from GWAS Summary Statistics

DEFF Research Database (Denmark)

Holland, Dominic; Wang, Yunpeng; Thompson, Wesley K

2016-01-01

Genome-wide Association Studies (GWAS) result in millions of summary statistics ("z-scores") for single nucleotide polymorphism (SNP) associations with phenotypes. These rich datasets afford deep insights into the nature and extent of genetic contributions to complex phenotypes such as psychiatric......-scores, as such knowledge would enhance causal SNP and gene discovery, help elucidate mechanistic pathways, and inform future study design. Here we present a parsimonious methodology for modeling effect sizes and replication probabilities, relying only on summary statistics from GWAS substudies, and a scheme allowing...... for estimating the degree of polygenicity of the phenotype and predicting the proportion of chip heritability explainable by genome-wide significant SNPs in future studies with larger sample sizes. We apply the model to recent GWAS of schizophrenia (N = 82,315) and putamen volume (N = 12,596), with approximately...

Conference summaries

Energy Technology Data Exchange (ETDEWEB)

Reynolds, Tim [Inta Communication Limited for European Service Network/ DG Research, Trillium House, 32 New Street, St. Neots, Cambridge PE19 1AJ (United Kingdom)

2004-07-01

The summaries were derived from presentations, interviews and discussions at the conference. The summaries are given at two levels, overall for the conference and for specific sessions as follows: 1) Overall Conference: 'A Sound Scientific Basis for Serious Decisions; 2) Sessions on EC Policy and Socio-Political Issues: 'Promoting Safety and Protecting Society'; 3) Session on P and T: 'Partitioning and Transmutation: A Technical Fix or Technical Training?'; 4) Sessions on Geological Disposal and Research Networking: 'No Technical Barriers to Geological Disposal'. First an overall summary of Euradwaste '04 is presented. Significant progress was made on the technical and scientific basis for geological disposal of radioactive waste during the European Commission's Fifth EURATOM Framework Programme for Research (FP5). Deep geological disposal is technically feasible now and can demonstrate the guarantees of long-term isolation and protection of the public. In parallel, socio-political studies have produced methodologies for constructive dialogue with potential host communities that reflect the honesty and openness expected by a democratic society. A harmonized legislative framework for nuclear safety and waste disposal across the enlarged European Union is currently being discussed. Disposal in deep (> 300 metre) geological repositories, the favoured strategy in Europe for long-lived high-level radioactive waste, is now possible. The Sessions on EC Policy and Socio-Political Issues are summarized as follows. The opening day of Euradwaste '04 focused on European Commission policy, including the proposed Directives on disposal of radioactive waste and nuclear safety and socio-political aspects including governance and decision making, public perception/acceptance of waste disposal and its sustainability. A decision on the proposed package will now be made after Union enlargement. Public agreement on the siting of

Common methodological flaws in economic evaluations.

Science.gov (United States)

Drummond, Michael; Sculpher, Mark

2005-07-01

Economic evaluations are increasingly being used by those bodies such as government agencies and managed care groups that make decisions about the reimbursement of health technologies. However, several reviews of economic evaluations point to numerous deficiencies in the methodology of studies or the failure to follow published methodological guidelines. This article, written for healthcare decision-makers and other users of economic evaluations, outlines the common methodological flaws in studies, focussing on those issues that are likely to be most important when deciding on the reimbursement, or guidance for use, of health technologies. The main flaws discussed are: (i) omission of important costs or benefits; (ii) inappropriate selection of alternatives for comparison; (iii) problems in making indirect comparisons; (iv) inadequate representation of the effectiveness data; (v) inappropriate extrapolation beyond the period observed in clinical studies; (vi) excessive use of assumptions rather than data; (vii) inadequate characterization of uncertainty; (viii) problems in aggregation of results; (ix) reporting of average cost-effectiveness ratios; (x) lack of consideration of generalizability issues; and (xi) selective reporting of findings. In each case examples are given from the literature and guidance is offered on how to detect flaws in economic evaluations.

Determination of the NPP Krsko reactor core safety limits using the COBRA-III-C code

International Nuclear Information System (INIS)

Lajtman, S.; Feretic, D.; Debrecin, N.

1989-01-01

This paper presents the NPP Krsko reactor core safety limits determined by the COBRA-III-C code, along with the methodology used. The reactor core safety limits determination is a part of reactor protection limits procedure. The results obtained were compared to safety limits presented in NPP Krsko FSAR. The COBRA-III-C NPP Krsko design core steady state thermal hydraulics calculation, used as the basis for the safety limits calculation, is presented as well. (author)

Project summary plan for HTGR recycle reference facility

International Nuclear Information System (INIS)

Baxter, B.J.

1979-11-01

A summary plan is introduced for completing conceptual definition of an HTGR Recycle Reference Facility (HRRF). The plan describes a generic project management concept, often referred to as the requirements approach to systems engineering. The plan begins with reference flow sheets and provides for the progressive evolution of HRRF requirements and definition through feasibility, preconceptual, and conceptual phases. The plan lays end-to-end all the important activities and elements to be treated during each phase of design. Identified activities and elements are further supported by technical guideline documents, which describe methodology, needed terminology, and where relevant a worked example

Solvent extraction of anionic chelate complexes of lanthanum(III), europium(III), lutetium(III), scandium(III), and indium(III) with 2-thenoyltrifluoroacetone as ion-pairs with tetrabutylammonium ions

International Nuclear Information System (INIS)

Noro, Junji; Sekine, Tatsuya.

1992-01-01

The solvent extraction of lanthanum(III), europium(III), lutetium(III), scandium(III), and indium(III) in 0.1 mol dm -3 sodium nitrate solutions with 2-thenoyltrifluoroacetone (Htta) in the absence and presence of tetrabutylammonium ions (tba + ) into carbon tetrachloride was measured. The extraction of lanthanum(III), europium(III), and lutetium(III) was greatly enhanced by the addition of tba + ; this could be explained in terms of the extraction of a ternary complex, M(tta) 4 - tba + . However, the extractions of scandium(III) and indium(III) were nearly the same when tba + was added. The data were treated on the basis of the formation equilibrium of the ternary complex from the neutral chelate, M(tta) 3 , with the extracted ion-pairs of the reagents, tta - tba + , in the organic phase. It was concluded that the degree of association of M(tta) 3 with the ion-pair, tta - tba + , is greater in the order La(tta) 3 ≅ Eu(tta) 3 > Lu(tta) 3 , or that the stability of the ternary complex in the organic phase is higher in the order La(tta) 4 - tba + ≅ Eu(tta) 4 - tba + > Lu(tta) 4 - tba + . This is similar to those of adduct metal chelates of Htta with tributylphosphate (TBP) in synergistic extraction systems. (author)

Sparkle/PM3 for the modeling of europium(III), gadolinium(III), and terbium(III) complexes

International Nuclear Information System (INIS)

Freire, Ricardo O.; Rocha, Gerd B.; Simas, Alfredo M.

2009-01-01

The Sparkle/PM3 model is extended to europium(III), gadolinium(III), and terbium(III) complexes. The validation procedure was carried out using only high quality crystallographic structures, for a total of ninety-six Eu(III) complexes, seventy Gd(III) complexes, and forty-two Tb(III) complexes. The Sparkle/PM3 unsigned mean error, for all interatomic distances between the trivalent lanthanide ion and the ligand atoms of the first sphere of coordination, is: 0.080 A for Eu(III); 0.063 A for Gd(III); and 0.070 A for Tb(III). These figures are similar to the Sparkle/AM1 ones of 0.082 A, 0.061 A, and 0.068 A respectively, indicating they are all comparable parameterizations. Moreover, their accuracy is similar to what can be obtained by present-day ab initio effective core potential full geometry optimization calculations on such lanthanide complexes. Finally, we report a preliminary attempt to show that Sparkle/PM3 geometry predictions are reliable. For one of the Eu(III) complexes, BAFZEO, we created hundreds of different input geometries by randomly varying the distances and angles of the ligands to the central Eu(III) ion, which were all subsequently fully optimized. A significant trend was unveiled, indicating that more accurate local minima geometries cluster at lower total energies, thus reinforcing the validity of sparkle model calculations. (author)

From Patient Discharge Summaries to an Ontology for Psychiatry.

Science.gov (United States)

Richard, Marion; Aimé, Xavier; Jaulent, Marie-Christine; Krebs, Marie-Odile; Charlet, Jean

2017-01-01

Psychiatry aims at detecting symptoms, providing diagnoses and treating mental disorders. We developed ONTOPSYCHIA, an ontology for psychiatry in three modules: social and environmental factors of mental disorders, mental disorders, and treatments. The use of ONTOPSYCHIA, associated with dedicated tools, will facilitate semantic research in Patient Discharge Summaries (PDS). To develop the first module of the ontology we propose a PDS text analysis in order to explicit psychiatry concepts. We decided to set aside classifications during the construction of the modu le, to focus only on the information contained in PDS (bottom-up approach) and to return to domain classifications solely for the enrichment phase (top-down approach). Then, we focused our work on the development of the LOVMI methodology (Les Ontologies Validées par Méthode Interactive - Ontologies Validated by Interactive Method), which aims to provide a methodological framework to validate the structure and the semantic of an ontology.

A Design Methodology for Medical Processes

Science.gov (United States)

Bonacina, Stefano; Pozzi, Giuseppe; Pinciroli, Francesco; Marceglia, Sara

2016-01-01

Summary Background Healthcare processes, especially those belonging to the clinical domain, are acknowledged as complex and characterized by the dynamic nature of the diagnosis, the variability of the decisions made by experts driven by their experiences, the local constraints, the patient’s needs, the uncertainty of the patient’s response, and the indeterminacy of patient’s compliance to treatment. Also, the multiple actors involved in patient’s care need clear and transparent communication to ensure care coordination. Objectives In this paper, we propose a methodology to model healthcare processes in order to break out complexity and provide transparency. Methods The model is grounded on a set of requirements that make the healthcare domain unique with respect to other knowledge domains. The modeling methodology is based on three main phases: the study of the environmental context, the conceptual modeling, and the logical modeling. Results The proposed methodology was validated by applying it to the case study of the rehabilitation process of stroke patients in the specific setting of a specialized rehabilitation center. The resulting model was used to define the specifications of a software artifact for the digital administration and collection of assessment tests that was also implemented. Conclusions Despite being only an example, our case study showed the ability of process modeling to answer the actual needs in healthcare practices. Independently from the medical domain in which the modeling effort is done, the proposed methodology is useful to create high-quality models, and to detect and take into account relevant and tricky situations that can occur during process execution. PMID:27081415

Summary report of technical meeting on neutron cross section covariances

International Nuclear Information System (INIS)

Trkov, A.; Smith, D.L.; Capote Noy, R.

2011-01-01

A summary is given of the Technical Meeting on Neutron Cross Section Covariances. The meeting goal was to assess covariance data needs and recommend appropriate methodologies to address those needs. Discussions on covariance data focused on three general topics: 1) Resonance and unresolved resonance regions; 2) Fast neutron region; and 3) Users' perspective: benchmarks' uncertainty and reactor dosimetry. A number of recommendations for further work were generated and the important work that remains to be done in the field of covariances was identified. (author)

Uranium (III)-Plutonium (III) co-precipitation in molten chloride

Science.gov (United States)

Vigier, Jean-François; Laplace, Annabelle; Renard, Catherine; Miguirditchian, Manuel; Abraham, Francis

2018-02-01

Co-management of the actinides in an integrated closed fuel cycle by a pyrochemical process is studied at the laboratory scale in France in the CEA-ATALANTE facility. In this context the co-precipitation of U(III) and Pu(III) by wet argon sparging in LiCl-CaCl2 (30-70 mol%) molten salt at 705 °C is studied. Pu(III) is prepared in situ in the molten salt by carbochlorination of PuO2 and U(III) is then introduced as UCl3 after chlorine purge by argon to avoid any oxidation of uranium up to U(VI) by Cl2. The oxide conversion yield through wet argon sparging is quantitative. However, the preferential oxidation of U(III) in comparison to Pu(III) is responsible for a successive conversion of the two actinides, giving a mixture of UO2 and PuO2 oxides. Surprisingly, the conversion of sole Pu(III) in the same conditions leads to a mixture of PuO2 and PuOCl, characteristic of a partial oxidation of Pu(III) to Pu(IV). This is in contrast with coconversion of U(III)-Pu(III) mixtures but in agreement with the conversion of Ce(III).

76 FR 79228 - Combined Licenses at William States Lee III Nuclear Station Site, Units 1 and 2; Duke Energy...

Science.gov (United States)

2011-12-21

... NUCLEAR REGULATORY COMMISSION [Docket Nos. 52-018 and 52-019; NRC-2008-0170] Combined Licenses at William States Lee III Nuclear Station Site, Units 1 and 2; Duke Energy Carolinas, LLC AGENCY: Nuclear.... SUMMARY: Notice is hereby given that the U.S. Nuclear Regulatory Commission (NRC) and the U.S. Army Corps...

Supplement to the Disposal Criticality Analysis Methodology

International Nuclear Information System (INIS)

Thomas, D.A.

1999-01-01

The methodology for evaluating criticality potential for high-level radioactive waste and spent nuclear fuel after the repository is sealed and permanently closed is described in the Disposal Criticality Analysis Methodology Topical Report (DOE 1998b). The topical report provides a process for validating various models that are contained in the methodology and states that validation will be performed to support License Application. The Supplement to the Disposal Criticality Analysis Methodology provides a summary of data and analyses that will be used for validating these models and will be included in the model validation reports. The supplement also summarizes the process that will be followed in developing the model validation reports. These reports will satisfy commitments made in the topical report, and thus support the use of the methodology for Site Recommendation and License Application. It is concluded that this report meets the objective of presenting additional information along with references that support the methodology presented in the topical report and can be used both in validation reports and in answering request for additional information received from the Nuclear Regulatory Commission concerning the topical report. The data and analyses summarized in this report and presented in the references are not sufficient to complete a validation report. However, this information will provide a basis for several of the validation reports. Data from several references in this report have been identified with TBV-1349. Release of the TBV governing this data is required prior to its use in quality affecting activities and for use in analyses affecting procurement, construction, or fabrication. Subsequent to the initiation of TBV-1349, DOE issued a concurrence letter (Mellington 1999) approving the request to identify information taken from the references specified in Section 1.4 as accepted data

Methodology of dose calculation for the SRS SAR

International Nuclear Information System (INIS)

Price, J.B.

1991-07-01

The Savannah River Site (SRS) Safety Analysis Report (SAR) covering K reactor operation assesses a spectrum of design basis accidents. The assessment includes estimation of the dose consequences from the analyzed accidents. This report discusses the methodology used to perform the dose analysis reported in the SAR and also includes the quantified doses. Doses resulting from postulated design basis reactor accidents in Chapter 15 of the SAR are discussed, as well as an accident in which three percent of the fuel melts. Doses are reported for both atmospheric and aqueous releases. The methodology used to calculate doses from these accidents as reported in the SAR is consistent with NRC guidelines and industry standards. The doses from the design basis accidents for the SRS reactors are below the limits set for commercial reactors by the NRC and also meet industry criteria. A summary of doses for various postulated accidents is provided

Chromium(III) release from chromium‐tanned leather elicits allergic contact dermatitis: a use test study

Science.gov (United States)

Erfani, Behnaz; Matura, Mihály; Lidén, Carola

2018-01-01

Summary Background Chromium (Cr) is a common skin sensitizer. The use of Cr(VI) in leather is restricted in the EU, but that of Cr(III) is not. Objectives To assess whether prolonged exposure to Cr‐tanned leather with mainly Cr(III) release may elicit allergic contact dermatitis in Cr‐allergic individuals. Method Ten Cr‐allergic subjects and 22 controls were patch tested with serial dilutions of Cr(III) and Cr(VI), and with leather samples. They then conducted a use test with a Cr‐tanned and a Cr‐free leather bracelet over a period of 3 weeks, for 12 h per day. Cr deposited on the skin from the bracelets was measured in the controls, and the diphenylcarbazide test for Cr(VI) and extraction tests for Cr(III) and Cr(VI) were conducted for the different leathers. Results Four of 10 Cr‐allergic subjects developed positive reactions to the Cr‐tanned bracelet within 7–21 days, whereas only 1 of 10 had a positive patch test reaction to this leather. Cr released from the Cr‐tanned leather was most probably entirely Cr(III), with a quantifiable amount being deposited on the skin. Conclusions This study strongly suggests that prolonged and repeated exposure to Cr‐tanned leather with mainly Cr(III) release is capable of eliciting allergic contact dermatitis in Cr‐allergic individuals. PMID:29322530

Washington International Renewable Energy Conference 2008 Pledges: Methodology and Assumptions Summary

Energy Technology Data Exchange (ETDEWEB)

Babiuch, B.; Bilello, D. E.; Cowlin, S. C.; Mann, M.; Wise, A.

2008-08-01

The 2008 Washington International Renewable Energy Conference (WIREC) was held in Washington, D.C., from March 4-6, 2008, and involved nearly 9,000 people from 125 countries. The event brought together worldwide leaders in renewable energy (RE) from governments, international organizations, nongovernmental organizations, and the private sector to discuss the role that renewables can play in alleviating poverty, growing economies, and passing on a healthy planet to future generations. The conference concluded with more than 140 governments, international organizations, and private-sector representatives pledging to advance the uptake of renewable energy. The U.S. government authorized the National Renewable Energy Laboratory (NREL) to estimate the carbon dioxide (CO2) savings that would result from the pledges made at the 2008 conference. This report describes the methodology and assumptions used by NREL in quantifying the potential CO2 reductions derived from those pledges.

Regional issue identification and assessment: study methodology. First annual report

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

The overall assessment methodologies and models utilized for the first project under the Regional Issue Identification and Assessment (RIIA) program are described. Detailed descriptions are given of the methodologies used by lead laboratories for the quantification of the impacts of an energy scenario on one or more media (e.g., air, water, land, human and ecology), and by all laboratories to assess the regional impacts on all media. The research and assessments reflected in this document were performed by the following national laboratories: Argonne National Laboratory; Brookhaven National Laboratory; Lawrence Berkeley Laboratory; Los Alamos Scientific Laboratory; Oak Ridge National Laboratory; and Pacific Northwest Laboratory. This report contains five chapters. Chapter 1 briefly describes the overall study methodology and introduces the technical participants. Chapter 2 is a summary of the energy policy scenario selected for the RIIA I study and Chapter 3 describes how this scenario was translated into a county-level siting pattern of energy development. The fourth chapter is a detailed description of the individual methodologies used to quantify the environmental and socioeconomic impacts of the scenario while Chapter 5 describes how these impacts were translated into comprehensive regional assessments for each Federal Region.

HRS Clinical Document Development Methodology Manual and Policies: Executive summary.

Science.gov (United States)

Indik, Julia H; Patton, Kristen K; Beardsall, Marianne; Chen-Scarabelli, Carol A; Cohen, Mitchell I; Dickfeld, Timm-Michael L; Haines, David E; Helm, Robert H; Krishnan, Kousik; Nielsen, Jens Cosedis; Rickard, John; Sapp, John L; Chung, Mina

2017-10-01

The Heart Rhythm Society (HRS) has been developing clinical practice documents in collaboration and partnership with other professional medical societies since 1996. The HRS formed a Scientific and Clinical Documents Committee (SCDC) with the sole purpose of managing the development of these documents from conception through publication. The SCDC oversees the process for developing clinical practice documents, with input and approval from the HRS Executive Committee and the Board of Trustees. As of May 2017, the HRS has produced more than 80 publications with other professional organizations. This process manual is produced to publicly and transparently declare the standards by which the HRS develops clinical practice documents, which include clinical practice guidelines, expert consensus statements, scientific statements, clinical competency statements, task force policy statements, and proceedings statements. The foundation for this process is informed by the Institute of Medicine's standards for developing trustworthy clinical practice guidelines; the new criteria from the National Guidelines Clearinghouse, effective June 2014; SCDC member discussions; and a review of guideline policies and methodologies used by other professional organizations. Copyright © 2017 Heart Rhythm Society. Published by Elsevier Inc. All rights reserved.

Methodology for combining dynamic responses. Technical report

International Nuclear Information System (INIS)

Mattu, R.K.

1980-05-01

Procedures in accordance with Appendix A of 10 CFR 50, GDC 2, call for an appropriate combination of the effects of the accident loads and loads caused by natural phenomena (such as earthquakes) to be reflected in the design bases of safety equipment. This requirement of interaction of loads has been implemented in various ways both within the NRC and the Nuclear Industry. An NRR Working Group constituted to examine load combination methodologies developed recommendations which were published in September 1978 as NUREG-0484, (PB-287 432). Revision 1 of NUREG-0484 extends the conclusions of the original NUREG-0484 on the use of SRSS methodology for the combination of SSE and LOCA responses beyond RCPB to any other ASME Section III, Class 1, 2, or 3 affected system, component or support, and provides criteria for the combination of dynamic responses other than SSE and LOCA

Summary Report of Commercial reactor Criticality Data for Three Mile Island Unit 1

International Nuclear Information System (INIS)

Larry B. Wimmer

2001-01-01

The objective of the ''Summary Report of Commercial Reactor Criticality Data for Three Mile Island Unit I'' is to present the CRC data for the TMI-1 reactor. Results from the CRC evaluations will support the development and validation of the neutronics models used for criticality analyses involving commercial spent nuclear fuel. These models and their validation are discussed in the ''Disposal Criticality Analysis Methodology Topical Report'' (YMP 2000)

ECU@Risk, a methodology for risk management applied to MSMEs

Directory of Open Access Journals (Sweden)

Esteban Crespo Martínez

2017-02-01

Full Text Available Information is the most valuable element for any organization or person in this new century, which, for many companies, is a competitive advantage asset (Vásquez & Gabalán, 2015. However, despite the lack of knowledge about how to protect it properly or the complexity of international standards that indicate procedures to achieve an adequate level of protection, many organizations, especially the MSMEs sector, fails to achieve this goal.Therefore, this study proposes a methodology for information security risk management, which is applicable to the business and organizational environment of the Ecuadorian MSME sector. For this purpose, we analyze several methodologies as Magerit, CRAMM (CCTA Risk Analysis and Management Method, OCTAVE-S, Microsoft Risk Guide, COBIT 5 COSO III. These methodologies are internationally used in risk management of information; in the light of the frameworks of the industry: ISO 27001, 27002, 27005 and 31000.

Waste Package Component Design Methodology Report

International Nuclear Information System (INIS)

D.C. Mecham

2004-01-01

This Executive Summary provides an overview of the methodology being used by the Yucca Mountain Project (YMP) to design waste packages and ancillary components. This summary information is intended for readers with general interest, but also provides technical readers a general framework surrounding a variety of technical details provided in the main body of the report. The purpose of this report is to document and ensure appropriate design methods are used in the design of waste packages and ancillary components (the drip shields and emplacement pallets). The methodology includes identification of necessary design inputs, justification of design assumptions, and use of appropriate analysis methods, and computational tools. This design work is subject to ''Quality Assurance Requirements and Description''. The document is primarily intended for internal use and technical guidance for a variety of design activities. It is recognized that a wide audience including project management, the U.S. Department of Energy (DOE), the U.S. Nuclear Regulatory Commission, and others are interested to various levels of detail in the design methods and therefore covers a wide range of topics at varying levels of detail. Due to the preliminary nature of the design, readers can expect to encounter varied levels of detail in the body of the report. It is expected that technical information used as input to design documents will be verified and taken from the latest versions of reference sources given herein. This revision of the methodology report has evolved with changes in the waste package, drip shield, and emplacement pallet designs over many years and may be further revised as the design is finalized. Different components and analyses are at different stages of development. Some parts of the report are detailed, while other less detailed parts are likely to undergo further refinement. The design methodology is intended to provide designs that satisfy the safety and operational

Waste Package Component Design Methodology Report

Energy Technology Data Exchange (ETDEWEB)

D.C. Mecham

2004-07-12

This Executive Summary provides an overview of the methodology being used by the Yucca Mountain Project (YMP) to design waste packages and ancillary components. This summary information is intended for readers with general interest, but also provides technical readers a general framework surrounding a variety of technical details provided in the main body of the report. The purpose of this report is to document and ensure appropriate design methods are used in the design of waste packages and ancillary components (the drip shields and emplacement pallets). The methodology includes identification of necessary design inputs, justification of design assumptions, and use of appropriate analysis methods, and computational tools. This design work is subject to ''Quality Assurance Requirements and Description''. The document is primarily intended for internal use and technical guidance for a variety of design activities. It is recognized that a wide audience including project management, the U.S. Department of Energy (DOE), the U.S. Nuclear Regulatory Commission, and others are interested to various levels of detail in the design methods and therefore covers a wide range of topics at varying levels of detail. Due to the preliminary nature of the design, readers can expect to encounter varied levels of detail in the body of the report. It is expected that technical information used as input to design documents will be verified and taken from the latest versions of reference sources given herein. This revision of the methodology report has evolved with changes in the waste package, drip shield, and emplacement pallet designs over many years and may be further revised as the design is finalized. Different components and analyses are at different stages of development. Some parts of the report are detailed, while other less detailed parts are likely to undergo further refinement. The design methodology is intended to provide designs that satisfy the safety

Summary of FY 1997 work related to JAPC-U.S. DOE contract study on improvement of core safety - study on GEM (III)

International Nuclear Information System (INIS)

Burke, T.M.

1998-01-01

FFTF was originally designed/constructed/operated to develop LMFBR fuels and materials. Inherent safety became a major focus of the US nuclear industry in the mid 1980's. The inherent safety characteristics of LMFBRs were recognized but additional enhancement was desired. The presentation contents are: Fast Flux Test Facility history and status; Overview of contract activities; Summary of loss of flow without scram with GEMs testing; and Summary of pump start with GEMs testing

76 FR 21036 - Application of the Prevailing Wage Methodology in the H-2B Program

Science.gov (United States)

2011-04-14

... Department to ``promulgate new rules concerning the calculation of the prevailing wage rate in the H-2B... wage methodology set forth in this Rule applies only to wages paid for work performed on or after...: Notice. SUMMARY: On January 19, 2011, the Department of Labor (Department) published a final rule, Wage...

Isolation, characterization, and stability of discretely-sized nanolipoprotein particles assembled with apolipophorin-III.

Directory of Open Access Journals (Sweden)

Nicholas O Fischer

Full Text Available BACKGROUND: Nanolipoprotein particles (NLPs are discoidal, nanometer-sized particles comprised of self-assembled phospholipid membranes and apolipoproteins. NLPs assembled with human apolipoproteins have been used for myriad biotechnology applications, including membrane protein solubilization, drug delivery, and diagnostic imaging. To expand the repertoire of lipoproteins for these applications, insect apolipophorin-III (apoLp-III was evaluated for the ability to form discretely-sized, homogeneous, and stable NLPs. METHODOLOGY: Four NLP populations distinct with regards to particle diameters (ranging in size from 10 nm to >25 nm and lipid-to-apoLp-III ratios were readily isolated to high purity by size exclusion chromatography. Remodeling of the purified NLP species over time at 4 degrees C was monitored by native gel electrophoresis, size exclusion chromatography, and atomic force microscopy. Purified 20 nm NLPs displayed no remodeling and remained stable for over 1 year. Purified NLPs with 10 nm and 15 nm diameters ultimately remodeled into 20 nm NLPs over a period of months. Intra-particle chemical cross-linking of apoLp-III stabilized NLPs of all sizes. CONCLUSIONS: ApoLp-III-based NLPs can be readily prepared, purified, characterized, and stabilized, suggesting their utility for biotechnological applications.

Distributing the Corporate Income Tax: Revised U.S. Treasury Methodology

OpenAIRE

Cronin, Julie Anne; Lin, Emily Y.; Power, Laura; Cooper, Michael

2013-01-01

The purpose of this analysis is to improve the U.S. Department of the Treasury’s distributional model and methodology by defining new model parameters. We compute the percentage of capital income attributable to normal versus supernormal return, the percentage of normal return attributable to the "cash flow tax" portion of the tax that does not impose a tax burden, and the portion of the burdensome tax on the normal return to capital borne by capital income versus labor income. In summary, 82...

Thermodecomposition of lanthanides (III) and ytrium (III) glucoheptonates

International Nuclear Information System (INIS)

Giolito, J.

1987-01-01

The lanthanides (III) and yttrium (III) glucoheptonates as well the D-glucoheptono 1-4 lactone were studied using common analytical methods, elemental microanalysis of carbon and hydrogen, thermogravimetry and differential scanning calorimetry. These compounds were prepared from the reaction between the lanthanides (III) and yttrium (III) hydroxides and glucoheptonic acid aqueous solution obtained by means of the delta lactone hydrolysis of this acid. After stoichiometric reaction the compounds were precipitated by the addition of absolute ethanol, washed with the same solvent and dried in desiccator. Thermogravimetric the (TG) curves of the lanthanides glucoheptonates of the ceric group present thermal profiles with enough differences permitting an easy caracterization of each compound and the yttrium (III) glucoheptonate TG curve showed a great similarity with the erbium (III) compound TG curve. The differential scanning calometry (DSC) curves showed endothermic and exothermic peaks by their shape, height and position (temperature) permit an easy and rapid identification of each compound specially if DSC and TG curves were examined simultaneously. (author) [pt

The Moessbauer effect in Fe(III) HEDTA, Fe(III) EDTA, and Fe(III) CDTA compounds

International Nuclear Information System (INIS)

Prado, F.R.

1989-01-01

The dependence of Moessbauer spectra with pH value of Fe(III)HEDTA and Fe(III)CDTA compounds is studied. Informations on formation processes of LFe-O-FeL (L=ligand) type dimers by the relation of titration curves of Fe(III)EDTA, Fe(III)HEDTA and Fe(III)CDTA compounds with the series of Moessbauer spectra, are obtained. Some informations on Fe-O-Fe bond structure are also obtained. Comparing the titration curves with the series of Moessbauer spectra, it is concluded that the dimerization process begins when a specie of the form FeXOH α (X = EDTA, HEDTA, CDTA; α = -1, -2) arises. (M.C.K.) [pt

Industrial Fuel Gas Demonstration Plant Program. Conceptual design and evaluation of commercial plant. Volume III. Economic analyses (Deliverable Nos. 15 and 16)

Energy Technology Data Exchange (ETDEWEB)

None

1978-01-01

This report presents the results of Task I of Phase I in the form of a Conceptual Design and Evaluation of Commercial Plant report. The report is presented in four volumes as follows: I - Executive Summary, II - Commercial Plant Design, III - Economic Analyses, IV - Demonstration Plant Recommendations. Volume III presents the economic analyses for the commercial plant and the supporting data. General cost and financing factors used in the analyses are tabulated. Three financing modes are considered. The product gas cost calculation procedure is identified and appendices present computer inputs and sample computer outputs for the MLGW, Utility, and Industry Base Cases. The results of the base case cost analyses for plant fenceline gas costs are as follows: Municipal Utility, (e.g. MLGW), $3.76/MM Btu; Investor Owned Utility, (25% equity), $4.48/MM Btu; and Investor Case, (100% equity), $5.21/MM Btu. The results of 47 IFG product cost sensitivity cases involving a dozen sensitivity variables are presented. Plant half size, coal cost, plant investment, and return on equity (industrial) are the most important sensitivity variables. Volume III also presents a summary discussion of the socioeconomic impact of the plant and a discussion of possible commercial incentives for development of IFG plants.

The endoplasmic reticulum is a target organelle for trivalent dimethylarsinic acid (DMA{sup III})-induced cytotoxicity

Energy Technology Data Exchange (ETDEWEB)

Naranmandura, Hua, E-mail: narenman@zju.edu.cn [Department of Pharmacology, Toxicology, and Biochemical Pharmaceutics, College of Pharmaceutical Sciences, Zhejiang University, Hangzhou 310058 (China); Xu, Shi [Department of Pharmacology, Toxicology, and Biochemical Pharmaceutics, College of Pharmaceutical Sciences, Zhejiang University, Hangzhou 310058 (China); Koike, Shota [Graduate School of Pharmaceutical Sciences, Chiba University, Chiba 260-8675 (Japan); Pan, Li Qiang [Department of Pharmacology, Toxicology, and Biochemical Pharmaceutics, College of Pharmaceutical Sciences, Zhejiang University, Hangzhou 310058 (China); Chen, Bin [Tongji Medical College, Huazhong University of Science and Technology, Wuhan, Hubei 430030 (China); Wang, Yan Wei; Rehman, Kanwal; Wu, Bin [Department of Pharmacology, Toxicology, and Biochemical Pharmaceutics, College of Pharmaceutical Sciences, Zhejiang University, Hangzhou 310058 (China); Chen, Zhe [Zhejiang Hospital of Traditional Chinese Medicine, Zhejiang Chinese Medical University, Hangzhou (China); Suzuki, Noriyuki, E-mail: n-suzuki@p.chiba-u.ac.jp [Graduate School of Pharmaceutical Sciences, Chiba University, Chiba 260-8675 (Japan)

2012-05-01

The purpose of present study was to characterize the endoplasmic reticulum stress and generation of ROS in rat liver RLC-16 cells by exposing to trivalent dimethylarsinous acid (DMA{sup III}) and compared with that of trivalent arsenite (iAs{sup III}) and monomethylarsonous acid (MMA{sup III}). Protein kinase-like endoplasmic reticulum kinase (PERK) phosphorylation was significantly induced in cells exposed to DMA{sup III}, while there was no change in phosphorylated PERK (P-PERK) detected in cells after exposure to iAs{sup III} or MMA{sup III}. The generation of reactive oxygen species (ROS) after DMA{sup III} exposure was found to take place specifically in the endoplasmic reticulum (ER), while previous reports showed that ROS was generated in mitochondria following exposure to MMA{sup III}. Meanwhile, cycloheximide (CHX) which is an inhibitor of protein biosynthesis strongly inhibited the DMA{sup III}-induced intracellular ROS generation in the ER and the phosphorylation of PERK, suggesting the induction of ER stress probably occurs through the inhibition of the protein folding process. Activating transcription factor 4 (ATF4) and C/EBP homologous protein (CHOP) mRNA were induced by all three arsenic species, however, evidence suggested that they might be induced by different pathways in the case of iAs{sup III} and MMA{sup III}. In addition, ER resident molecular chaperone glucose-regulated protein78 (GRP78) was not affected by trivalent arsenicals, while it was induced in positive control only at high concentration (Thapsigargin;Tg), suggesting the GRP78 is less sensitive to low levels of ER stress. In summary, our findings demonstrate that the endoplasmic reticulum is a target organelle for DMA{sup III}-induced cytotoxicity. Highlights: ►ER is a target organelle for trivalent DMA{sup III}-induced cytotoxicity. ►Generation of ROS in ER can be induced specially by trivalent DMA{sup III}. ►ER-stress and generation of ROS are caused by the increase in

Summary of the technical guidelines used in the project: The economics of greenhouse gas limitations

International Nuclear Information System (INIS)

Halsnaes, Kirsten

1998-01-01

This document is a summary version of the technical guidelines for climate change mitigation assessment developed as a part of the Global Environment Facility (GEF) project The Economics of Greenhouse Gas Limitations; Technical guidelines (UNEP 1998). The objectives of this project have been to support the development of a methodology, an implementing framework and a reporting system which countries can use in the construction of national climate change policies and in meeting their future reporting obligations under the FCCC. The methodological framework developed in the guidelines covers key economic concepts, scenario building, modelling tools and common assumptions. It was used by several country studies included in the project. (au)

Spanish methodological approach for biosphere assessment of radioactive waste disposal

International Nuclear Information System (INIS)

Agueero, A.; Pinedo, P.; Cancio, D.; Simon, I.; Moraleda, M.; Perez-Sanchez, D.; Trueba, C.

2007-01-01

The development of radioactive waste disposal facilities requires implementation of measures that will afford protection of human health and the environment over a specific temporal frame that depends on the characteristics of the wastes. The repository design is based on a multi-barrier system: (i) the near-field or engineered barrier, (ii) far-field or geological barrier and (iii) the biosphere system. Here, the focus is on the analysis of this last system, the biosphere. A description is provided of conceptual developments, methodological aspects and software tools used to develop the Biosphere Assessment Methodology in the context of high-level waste (HLW) disposal facilities in Spain. This methodology is based on the BIOMASS 'Reference Biospheres Methodology' and provides a logical and systematic approach with supplementary documentation that helps to support the decisions necessary for model development. It follows a five-stage approach, such that a coherent biosphere system description and the corresponding conceptual, mathematical and numerical models can be built. A discussion on the improvements implemented through application of the methodology to case studies in international and national projects is included. Some facets of this methodological approach still require further consideration, principally an enhanced integration of climatology, geography and ecology into models considering evolution of the environment, some aspects of the interface between the geosphere and biosphere, and an accurate quantification of environmental change processes and rates

Spanish methodological approach for biosphere assessment of radioactive waste disposal.

Science.gov (United States)

Agüero, A; Pinedo, P; Cancio, D; Simón, I; Moraleda, M; Pérez-Sánchez, D; Trueba, C

2007-10-01

The development of radioactive waste disposal facilities requires implementation of measures that will afford protection of human health and the environment over a specific temporal frame that depends on the characteristics of the wastes. The repository design is based on a multi-barrier system: (i) the near-field or engineered barrier, (ii) far-field or geological barrier and (iii) the biosphere system. Here, the focus is on the analysis of this last system, the biosphere. A description is provided of conceptual developments, methodological aspects and software tools used to develop the Biosphere Assessment Methodology in the context of high-level waste (HLW) disposal facilities in Spain. This methodology is based on the BIOMASS "Reference Biospheres Methodology" and provides a logical and systematic approach with supplementary documentation that helps to support the decisions necessary for model development. It follows a five-stage approach, such that a coherent biosphere system description and the corresponding conceptual, mathematical and numerical models can be built. A discussion on the improvements implemented through application of the methodology to case studies in international and national projects is included. Some facets of this methodological approach still require further consideration, principally an enhanced integration of climatology, geography and ecology into models considering evolution of the environment, some aspects of the interface between the geosphere and biosphere, and an accurate quantification of environmental change processes and rates.

AMS-C14 analysis of graphite obtained with an Automated Graphitization Equipment (AGE III) from aerosol collected on quartz filters

Energy Technology Data Exchange (ETDEWEB)

Solís, C.; Chávez, E.; Ortiz, M.E.; Andrade, E. [Instituto de Física, Universidad Nacional Autónoma de México, 04510 México D.F. (Mexico); Ortíz, E. [Universidad Autónoma Metropolitana, Unidad Azcapotzalco, México D.F. (Mexico); Szidat, S. [Department of Chemistry and Biochemistry, University of Bern, Freiestrasse 3, CH-3012 Bern (Switzerland); Paul Scherrer Institut (PSI), CH-5232 Villigen (Switzerland); Wacker, L. [Laboratory of Ion Physics, ETH, Honggerberg, Zurich (Switzerland)

2015-10-15

AMS-{sup 14}C applications often require the analysis of small samples. Such is the case of atmospheric aerosols where frequently only a small amount of sample is available. The ion beam physics group at the ETH, Zurich, has designed an Automated Graphitization Equipment (AGE III) for routine graphite production for AMS analysis from organic samples of approximately 1 mg. In this study, we explore the potential use of the AGE III for graphitization of particulate carbon collected in quartz filters. In order to test the methodology, samples of reference materials and blanks with different sizes were prepared in the AGE III and the graphite was analyzed in a MICADAS AMS (ETH) system. The graphite samples prepared in the AGE III showed recovery yields higher than 80% and reproducible {sup 14}C values for masses ranging from 50 to 300 μg. Also, reproducible radiocarbon values were obtained for aerosol filters of small sizes that had been graphitized in the AGE III. As a study case, the tested methodology was applied to PM{sub 10} samples collected in two urban cities in Mexico in order to compare the source apportionment of biomass and fossil fuel combustion. The obtained {sup 14}C data showed that carbonaceous aerosols from Mexico City have much lower biogenic signature than the smaller city of Cuernavaca.

Research Summaries

Science.gov (United States)

Brock, Stephen E., Ed.

2011-01-01

This article presents summaries of three articles relevant to school crisis response: (1) "Factors Contributing to Posttraumatic Growth," summarized by Steve DeBlois; (2) "Psychological Debriefing in Cross-Cultural Contexts" (Stacey Rice); and (3) "Brain Abnormalities in PTSD" (Sunny Windingstad). The first summary reports the findings of a…

How to emerge from the conservatism in clinical research methodology?

Science.gov (United States)

Kotecki, Nuria; Penel, Nicolas; Awada, Ahmad

2017-09-01

Despite recent changes in clinical research methodology, many challenges remain in drug development methodology. Advances in molecular biology and cancer treatments have changed the clinical research landscape. Thus, we moved from empirical clinical oncology to molecular and immunological therapeutic approaches. Along with this move, adapted dose-limiting toxicities definitions, endpoints, and dose escalation methods have been proposed. Moreover, the classical frontier between phase I, phase II, and phase III has become unclear in particular for immunological approaches. So, investigators are facing major challenges in drug development methodology. We propose to individualize clinical research using innovative approaches to significantly improve patient outcomes and targeting what is considered unmet need. Integrating high level of translational research and performing well designed biomarker studies with great potential for clinical practice are of utmost importance. This could be performed within new models of clinical research networks and by building a strong collaboration between academic, cooperative groups, on-site investigators, and pharma.

Sorption of trace amounts of gallium (III) on iron (III) oxide

International Nuclear Information System (INIS)

Music, S.; Gessner, M.; Wolf, R.H.H.

1979-01-01

The sorption of trace amounts of gallium(III) on iron(III) oxide has been studied as a function of pH. Optimum conditions have been found for the preconcentration of traces of gallium(III) by iron(III) oxide. The influence of surface active substances and of complexing agents on the sorption of trace amounts of gallium(III) on iron(III) oxide has been also studied. (orig.) [de

Sorption of trace amounts of gallium (III) on iron (III) oxide

Energy Technology Data Exchange (ETDEWEB)

Music, S; Gessner, M; Wolf, R H.H. [Institut Rudjer Boskovic, Zagreb (Yugoslavia)

1979-01-01

The sorption of trace amounts of gallium(III) on iron(III) oxide has been studied as a function of pH. Optimum conditions have been found for the preconcentration of traces of gallium(III) by iron(III) oxide. The influence of surface active substances and of complexing agents on the sorption of trace amounts of gallium(III) on iron(III) oxide has been also studied.

WISC-III e WAIS-III na avaliação da inteligência de cegos WISC-III/WAIS-III en ciegos WISC-III and WAIS-III in intellectual assessment of blind people

Directory of Open Access Journals (Sweden)

Elizabeth do Nascimento

2007-12-01

Full Text Available Diante da escassez de pesquisas nacionais e de testes psicológicos destinados a avaliar pessoas cegas, desenvolveu-se um estudo psicométrico com as escalas verbais dos testes WISC-III e WAIS-III. Após as adaptações de alguns estímulos e das instruções, os testes foram aplicados em crianças (N = 120 e adultos (N = 52 residentes em Belo Horizonte. Os resultados indicaram que as escalas verbais modificadas apresentam uma boa consistência interna (alfa> 0,80. Além disso, a investigação da validade fatorial identifica a presença clara de apenas um componente. Este componente explica 81% e 64% para o WISC-III e WAIS-III, respectivamente. Conclui-se que as adaptações a que se procedeu não afetaram a estrutura fatorial das escalas. Deste modo, os profissionais poderão utilizar as escalas modificadas para avaliar a inteligência de pessoas cegas.Frente a la escasez de investigaciones nacionales asi como la ausencia de tests psicológicos que evaluen personas ciegas, se ha desarrollado un estudio psicometrico com la escalas verbales del WISC-III y WAIS-III. Posteriormente a las adaptaciones de algunos estímulos y de las instrucciones, las escalas fueron aplicadas a una muestra de niños (n=120 y de adultos (n=52 residentes en la ciudad de Belo Horizonte-Brasil. Los resultados indican que las escalas verbales modificadas presentan una alta fiabilidad (alpha >0,80 asi como la presencia clara de un unico componente responsable por 81% y 64% de la variancia del WIC-III e WAIS-III respectivamente. Se ha concluido que las modificaciones efectuadas no han comprometido la estructura factorial de las escalas verbales. Por tanto, los profesionales psicólogos pueden utilizar las escalas modificadas para la evaluación de la inteligencia de personas portadoras de ceguera.Owing to the almost lack of a national research on psychological testing for the evaluation of blind people, a psychometric study has been developed with the WISC-III and WAIS-III

Annotated bibliography for liquid metal surface tensions of groups III-A, IV-A, and V-A metals

International Nuclear Information System (INIS)

Murtha, M.J.; Burnet, G.

1976-04-01

An annotated bibliography has been prepared which includes summaries of 82 publications dating from 1920 and dealing with the measurement of the surface tensions of Groups III-A, IV-A, and V-A metals in the liquid state. The bibliography is organized by key element investigated, and contains a tabulation of correlations for surface tension as a function of temperature. A brief discussion dealing with variables and methods has been included

Particle Aggregation During Fe(III) Bioreduction in Nontronite

Science.gov (United States)

Jaisi, D. P.; Dong, H.; Hi, Z.; Kim, J.

2005-12-01

the particles size of 0.12-0.22 and 1.42-1.8 mm, respectively. The particle aggregation was limited in control experiment to the factor of 2.8 and 2.1 for these two size fractions, respectively. The measured electrophoretic mobility decreased with increase in the extent of bioreduction and aggregation, but the rate of decrease was greatest in the finest size fraction. The EPS measurements showed the increase in the carbohydrate and protein fractions as a result of bioreduction. Separate experiments were performed to understand the relative contribution of Fe(III) reduction and EPS production in controlling nontronite particle aggregation The rate of particle aggregation was measured for nontronite that was chemically pre-reduced by dithionite to various extents, both with and without addition of dextran, a neutral and pure EPS. The aggregation rate was greater in the nontronite that were pre-reduced to a higher extent than those with a lower extent of reduction. The relative contribution to particle aggregation due to Fe(III) reduction and polysaccharide bridging was about 4:1. However, in the real system where bacterial cells are involved, and amount of EPS production and extent of Fe(III) bioreduction increase with time, the relative contribution may be different than in this simple system. In summary, we conclude that both Fe(III) reduction and microbial production of EPS contribute to the observed nontronite particle aggregation with Fe(III) reduction playing more dominant role.

31 CFR 26.3 - Availability of Environmental Impact Assessment Summaries (EIA Summaries) and Environmental...

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Availability of Environmental Impact Assessment Summaries (EIA Summaries) and Environmental Impact Assessments (EIAs). 26.3 Section 26.3 Money and... DEVELOPMENT BANDS (MDBs) § 26.3 Availability of Environmental Impact Assessment Summaries (EIA Summaries) and...

Joint probability of statistical success of multiple phase III trials.

Science.gov (United States)

Zhang, Jianliang; Zhang, Jenny J

2013-01-01

In drug development, after completion of phase II proof-of-concept trials, the sponsor needs to make a go/no-go decision to start expensive phase III trials. The probability of statistical success (PoSS) of the phase III trials based on data from earlier studies is an important factor in that decision-making process. Instead of statistical power, the predictive power of a phase III trial, which takes into account the uncertainty in the estimation of treatment effect from earlier studies, has been proposed to evaluate the PoSS of a single trial. However, regulatory authorities generally require statistical significance in two (or more) trials for marketing licensure. We show that the predictive statistics of two future trials are statistically correlated through use of the common observed data from earlier studies. Thus, the joint predictive power should not be evaluated as a simplistic product of the predictive powers of the individual trials. We develop the relevant formulae for the appropriate evaluation of the joint predictive power and provide numerical examples. Our methodology is further extended to the more complex phase III development scenario comprising more than two (K > 2) trials, that is, the evaluation of the PoSS of at least k₀ (k₀≤ K) trials from a program of K total trials. Copyright © 2013 John Wiley & Sons, Ltd.

Erbium(III) in aqueous solution: an ab initio molecular dynamics study.

Science.gov (United States)

Canaval, Lorenz R; Sakwarathorn, Theerathad; Rode, Bernd M; Messner, Christoph B; Lutz, Oliver M D; Bonn, Günther K

2013-12-05

Structural and dynamical properties of the erbium(III) ion in water have been obtained by means of ab initio quantum mechanical charge field molecular dynamics (QMCF-MD) simulations for the ground state and an excited state. The quality of the simulations has been monitored by recording UV/vis and Raman spectra of dilute solutions of ErCl3 and Er(NO3)3 in water and by comparison with EXAFS data from literature. Slight deviations between these data can be mainly attributed to relativistic effects, which are not sufficiently considered by the methodological framework. In both simulations, a mixture of coordination numbers eight and nine and a ligand exchange on the picosecond range are observed. The strength of the Er-ligand bond is considerably lower than that of trivalent transition metal ions but higher than that for La(III) and Ce(III) in aqueous solution. The main difference between ground state and excited state is the ligand exchange rate of the first shell. The second hydration shell is stable in both cases but with significantly different properties.

A generic methodology for the design of sustainable carbon dioxide utilization processes using superstructure optimization

DEFF Research Database (Denmark)

Frauzem, Rebecca; Gani, Rafiqul

, including as an extractive agent or raw material. Chemical conversion, an important element of utilization, involves the use of carbon dioxide as a reactant in the production of chemical compounds [2]. However, for feasible implementation, a systematic methodology is needed for the design of the utilization......, especially chemical conversion, processes. To achieve this, a generic methodology has been developed, which adopts a three-stage approach consisting in (i) process synthesis, (ii) process design, and (iii) innovative and sustainable design [3]. This methodology, with the individual steps and associated...... methods and tools, has been developed and applied to carbon dioxide utilization networks. This work will focus on the first stage, process synthesis, of this three-stage methodology; process synthesis is important in determining the appropriate processing route to produce products from a selection...

Taking Word Clouds Apart: An Empirical Investigation of the Design Space for Keyword Summaries.

Science.gov (United States)

Felix, Cristian; Franconeri, Steven; Bertini, Enrico

2018-01-01

In this paper we present a set of four user studies aimed at exploring the visual design space of what we call keyword summaries: lists of words with associated quantitative values used to help people derive an intuition of what information a given document collection (or part of it) may contain. We seek to systematically study how different visual representations may affect people's performance in extracting information out of keyword summaries. To this purpose, we first create a design space of possible visual representations and compare the possible solutions in this design space through a variety of representative tasks and performance metrics. Other researchers have, in the past, studied some aspects of effectiveness with word clouds, however, the existing literature is somewhat scattered and do not seem to address the problem in a sufficiently systematic and holistic manner. The results of our studies showed a strong dependency on the tasks users are performing. In this paper we present details of our methodology, the results, as well as, guidelines on how to design effective keyword summaries based in our discoveries.

A survey of dynamic methodologies for probabilistic safety assessment of nuclear power plants

International Nuclear Information System (INIS)

Aldemir, Tunc

2013-01-01

Highlights: ► Dynamic methodologies for probabilistic safety assessment (PSA) are surveyed. ► These methodologies overcome the limitations of the traditional approach to PSA. ► They are suitable for PSA using a best estimate plus uncertainty approach. ► They are highly computation intensive and produce very large number of scenarios. ► Use of scenario clustering can assist the analysis of the results. -- Abstract: Dynamic methodologies for probabilistic safety assessment (PSA) are defined as those which use a time-dependent phenomenological model of system evolution along with its stochastic behavior to account for possible dependencies between failure events. Over the past 30 years, numerous concerns have been raised in the literature regarding the capability of the traditional static modeling approaches such as the event-tree/fault-tree methodology to adequately account for the impact of process/hardware/software/firmware/human interactions on the stochastic system behavior. A survey of the types of dynamic PSA methodologies proposed to date is presented, as well as a brief summary of an example application for the PSA modeling of a digital feedwater control system of an operating pressurized water reactor. The use of dynamic methodologies for PSA modeling of passive components and phenomenological uncertainties are also discussed.

Extraction and separation studies of Ga(III, In(III and Tl(III using the neutral organophosphorous extractant, Cyanex-923

Directory of Open Access Journals (Sweden)

P. M. DHADKE

2003-07-01

Full Text Available The neutral extractant, Cyanes-923 has been used for the extraction and separation of gallium(III, indium(III and thallium(III from acidic solution. These metal ions were found to be quantitatively extracted with Cyanex-923 in toluene in the pH range 4.5–5.5, 5.0–6.5 and 1.5–3.0, respectively, and from the organic phase they can be stripped with 2.0 mol dm-3 HNO3, 3.0 mol dm-3 HNO3 and 3.0 mol dm-3 HCl, respectively. The effect of pH equilibration period, diluents, diverse ions and stripping agents on the extraction of Ga(III, In(III and Tl(III has been studied. The stroichiometry of the extracted species of these metal ions was determined on the basis of the slope analysis method. The reaction proceed by solvation and the probable extracted species found were [MCl3. 3Cyanex-923] [where M = Ga(III or In(III ] and [HTlCl4. 3Cyanex-923]. Based on these results a sequential procedure for the separation of Ga(III, In(III and Tl(III from each other was developed.

Iron(II) and Iron(III) Spin Crossover: Toward an Optimal Density Functional

DEFF Research Database (Denmark)

Siig, Oliver S; Kepp, Kasper P.

2018-01-01

Spin crossover (SCO) plays a major role in biochemistry, catalysis, materials, and emerging technologies such as molecular electronics and sensors, and thus accurate prediction and design of SCO systems is of high priority. However, the main tool for this purpose, density functional theory (DFT......), is very sensitive to applied methodology. The most abundant SCO systems are Fe(II) and Fe(III) systems. Even with average good agreement, a functional may be significantly more accurate for Fe(II) or Fe(III) systems, preventing balanced study of SCO candidates of both types. The present work investigates....../precise, inaccurate/imprecise) are observed. More generally, our work illustrates the importance not only of overall accuracy but also of balanced accuracy for systems likely to occur in context....

Potentiometric studies on some ternary complexes of Nd(III), Sm(III), Gd(III) and Ho(III) with cyclohexanediaminetetraacetic acid as primary ligand

International Nuclear Information System (INIS)

Marathe, D.G.; Munshi, K.N.

1983-01-01

The formation constants of the ternary complexes of neodymium(III), samarium(III), gadlonium(III) and holmium(III) with cyclohexanediaminetetraacetic acid (CyDTA) as primary ligand and dihydroxynaphthalene (DHN), dihydroxynaphthalene-6-sulphonic acid (DHNSA) and cateechol-3,5-disulphonic acid (CDSA) as secondary ligands have been investigated by potentiometric titration technique. The secondary ligands have been investigated by potentiometric titration technique. The values of formation constants of 1:1:1 ternary chelates are reported at three different temperatures, and at a fixed ionic strength, μ = 0.1 M (NaClO 4 ). (author)

International consensus statement on allergy and rhinology: allergic rhinitis-executive summary.

Science.gov (United States)

Wise, Sarah K; Lin, Sandra Y; Toskala, Elina

2018-02-01

The available allergic rhinitis (AR) literature continues to grow. Critical evaluation and understanding of this literature is important to appropriately utilize this knowledge in the care of AR patients. The International Consensus statement on Allergy and Rhinology: Allergic Rhinitis (ICAR:AR) has been produced as a multidisciplinary international effort. This Executive Summary highlights and summarizes the findings of the comprehensive ICAR:AR document. The ICAR:AR document was produced using previously described methodology. Specific topics were developed relating to AR. Each topic was assigned a literature review, evidence-based review (EBR), or evidence-based review with recommendations (EBRR) format as dictated by available evidence and purpose within the ICAR:AR document. Following iterative reviews of each topic, the ICAR:AR document was synthesized and reviewed by all authors for consensus. Over 100 individual topics related to AR diagnosis, pathophysiology, epidemiology, disease burden, risk factors, allergy testing modalities, treatment, and other conditions/comorbidities associated with AR were addressed in the comprehensive ICAR:AR document. Herein, the Executive Summary provides a synopsis of these findings. In the ICAR:AR critical review of the literature, several strengths were identified. In addition, significant knowledge gaps exist in the AR literature where current practice is not based on the best quality evidence; these should be seen as opportunities for additional research. The ICAR:AR document evaluates the strengths and weaknesses of the AR literature. This Executive Summary condenses these findings into a short summary. The reader is also encouraged to consult the comprehensive ICAR:AR document for a thorough description of this work. © 2018 ARS-AAOA, LLC.

Methodology to build medical ontology from textual resources.

Science.gov (United States)

Baneyx, Audrey; Charlet, Jean; Jaulent, Marie-Christine

2006-01-01

In the medical field, it is now established that the maintenance of unambiguous thesauri goes through ontologies. Our research task is to help pneumologists code acts and diagnoses with a software that represents medical knowledge through a domain ontology. In this paper, we describe our general methodology aimed at knowledge engineers in order to build various types of medical ontologies based on terminology extraction from texts. The hypothesis is to apply natural language processing tools to textual patient discharge summaries to develop the resources needed to build an ontology in pneumology. Results indicate that the joint use of distributional analysis and lexico-syntactic patterns performed satisfactorily for building such ontologies.

Solvent effects on extraction of aluminum(III), gallium(III), and indium(III), with decanoic acid

International Nuclear Information System (INIS)

Yamada, Hiromichi; Hayashi, Hisao; Fujii, Yukio; Mizuta, Masateru

1986-01-01

Extraction of aluminum(III) and indium(III) with decanoic acid in 1-octanol was carried out at 25 deg C and at an aqueous ionic strength of 0.1 mol dm -3 (NaClO 4 ). Monomeric and tetrameric aluminum(III) decanoates and monomeric indium(III) decanoate are responsible for the extraction. From a comparison of the present results with those obtained from the previous works, the polymerization of the extracted species was found to be more extensive in benzene than in 1-octanol, and the metal decanoates were highly polymerized in the following order in both solvents: Al > Ga > In. (author)

Methodological issues affecting the study of fish parasites. III. Effect of fish preservation method

Czech Academy of Sciences Publication Activity Database

Kvach, Yuriy; Ondračková, Markéta; Janáč, Michal; Jurajda, Pavel

2018-01-01

Roč. 127, č. 3 (2018), s. 213-224 ISSN 0177-5103 R&D Projects: GA ČR(CZ) GBP505/12/G112 Institutional support: RVO:68081766 Keywords : flounder Paralichthys-olivaceus * Neoheterobothrium-hirame * community structure * infection levels * Baltic sea * Odontobutidae * ectoparasites * Perciformes * collection * ecology * Parasite community * Preservation methods * Perca fluviatilis * Rhodeus amarus * Methodology * Parasitological examination Subject RIV: GL - Fish ing OBOR OECD: Fish ery Impact factor: 1.549, year: 2016

Executive Summary - Natural Gas and the Transformation of the U.S. Energy Sector: Electricity

Energy Technology Data Exchange (ETDEWEB)

Logan, J.; Heath, G.; Macknick, J.; Paranhos, E.; Boyd, W.; Carlson, K.

2013-01-01

In November 2012, the Joint Institute for Strategic Energy Analysis (JISEA) released a new report, 'Natural Gas and the Transformation of the U.S. Energy Sector: Electricity.' The study provides a new methodological approach to estimate natural gas related greenhouse gas (GHG) emissions, tracks trends in regulatory and voluntary industry practices, and explores various electricity futures. The Executive Summary provides key findings, insights, data, and figures from this major study.

Abstract analysis method facilitates filtering low-methodological quality and high-bias risk systematic reviews on psoriasis interventions.

Science.gov (United States)

Gómez-García, Francisco; Ruano, Juan; Aguilar-Luque, Macarena; Alcalde-Mellado, Patricia; Gay-Mimbrera, Jesús; Hernández-Romero, José Luis; Sanz-Cabanillas, Juan Luis; Maestre-López, Beatriz; González-Padilla, Marcelino; Carmona-Fernández, Pedro J; García-Nieto, Antonio Vélez; Isla-Tejera, Beatriz

2017-12-29

Article summaries' information and structure may influence researchers/clinicians' decisions to conduct deeper full-text analyses. Specifically, abstracts of systematic reviews (SRs) and meta-analyses (MA) should provide structured summaries for quick assessment. This study explored a method for determining the methodological quality and bias risk of full-text reviews using abstract information alone. Systematic literature searches for SRs and/or MA about psoriasis were undertaken on MEDLINE, EMBASE, and Cochrane database. For each review, quality, abstract-reporting completeness, full-text methodological quality, and bias risk were evaluated using Preferred Reporting Items for Systematic Reviews and Meta-analyses for abstracts (PRISMA-A), Assessing the Methodological Quality of Systematic Reviews (AMSTAR), and ROBIS tools, respectively. Article-, author-, and journal-derived metadata were systematically extracted from eligible studies using a piloted template, and explanatory variables concerning abstract-reporting quality were assessed using univariate and multivariate-regression models. Two classification models concerning SRs' methodological quality and bias risk were developed based on per-item and total PRISMA-A scores and decision-tree algorithms. This work was supported, in part, by project ICI1400136 (JR). No funding was received from any pharmaceutical company. This study analysed 139 SRs on psoriasis interventions. On average, they featured 56.7% of PRISMA-A items. The mean total PRISMA-A score was significantly higher for high-methodological-quality SRs than for moderate- and low-methodological-quality reviews. SRs with low-bias risk showed higher total PRISMA-A values than reviews with high-bias risk. In the final model, only 'authors per review > 6' (OR: 1.098; 95%CI: 1.012-1.194), 'academic source of funding' (OR: 3.630; 95%CI: 1.788-7.542), and 'PRISMA-endorsed journal' (OR: 4.370; 95%CI: 1.785-10.98) predicted PRISMA-A variability. Reviews with a

Methodology for teaching technical pattern of lying, sport shooting. Mistakes often.

Directory of Open Access Journals (Sweden)

Yaydel Avila Gómez

2011-09-01

Full Text Available The next album we set out a summary of the key technical elements for a good development of the prone position, bearing in mind that sometimes violate some methodological steps for teaching the same in athletes who play sports Shooting sports Rifle mode, which creates bad habits in the teaching of the position are difficult to eradicate later. We proceeded to perform the following steps. Criteria for experts to determine methodological steps to be taken into account in the teaching of technical pattern prone position; query bibliographic elements of the sport, the explanation of the basic technical elements; survey a group of coaches in the form of Rifle for the determination of the most common mistakes in the process of teaching the technical pattern of the prone position. It came to the conclusion that teaching the correct technical pattern that position must be taken into account methodological steps which do not allow making any error that would create a dynamic stereotype wrong in athletes who subsequently would be difficult to resolve.

Design of an Integrated Methodology for Analytical Design of Complex Supply Chains

Directory of Open Access Journals (Sweden)

Shahid Rashid

2012-01-01

Full Text Available A literature review and gap analysis indentifies key limitations of industry best practice when modelling of supply chains. To address these limitations the paper reports on the conception and development of an integrated modelling methodology designed to underpin the analytical design of complex supply chains. The methodology is based upon a systematic deployment of EM, CLD, and SM techniques; the integration of which is achieved via common modelling concepts and decomposition principles. Thereby the methodology facilitates: (i graphical representation and description of key “processing”, “resourcing” and “work flow” properties of supply chain configurations; (ii behavioural exploration of currently configured supply chains, to facilitate reasoning about uncertain demand impacts on supply, make, delivery, and return processes; (iii predictive quantification about relative performances of alternative complex supply chain configurations, including risk assessments. Guidelines for the application of each step of the methodology are described. Also described are recommended data collection methods and expected modelling outcomes for each step. The methodology is being extensively case tested to quantify potential benefits & costs relative to current best industry practice. The paper reflects on preliminary benefits gained during industry based case study modelling and identifies areas of potential improvement.

Risk analysis methodology for spent fuel repositories in bedded salt: methodlogy summary and differences between spent fuel and high level wastes

International Nuclear Information System (INIS)

Pepping, R.E.; Chu, M.S.

1981-06-01

In the absence of spent fuel reprocessing plans, unreprocessed spent fuel has become a candidate waste form for geologic disposal. In order to understand the public health risks from such disposal and to gain insights into the factors that influence them, a methodology is needed to combine the effects of site geology and hydrology, physical and chemical properties of the waste form, and the details of the engineering design. This report outlines such a methodology which the authors currently are applying to the analysis of unreprocessed spent fuel disposal. The methodology is the same methodology as was developed to describe the risks from geologic disposal of wastes from reprocessed spent fuel. The difference between spent fuel wastes and wastes from reprocessing that may affect the applicability of the methodology are highlighted

Preparing for budget-based payment methodologies: global payment and episode-based payment.

Science.gov (United States)

Hudson, Mark E

2015-10-01

Use of budget-based payment methodologies (capitation and episode-based bundled payment) has been demonstrated to drive value in healthcare delivery. With a focus on high-volume, high-cost surgical procedures, inclusion of anaesthesiology services in these methodologies is likely. This review provides a summary of budget-based payment methodologies and practical information necessary for anaesthesiologists to prepare for participation in these programmes. Although few examples of anaesthesiologists' participation in these models exist, an understanding of the structure of these programmes and opportunities for participation are available. Prospective preparation in developing anaesthesiology-specific bundled payment profiles and early participation in pathway development associated with selected episodes of care are essential for successful participation as a gainsharing partner. With significant opportunity to contribute to care coordination and cost management, anaesthesiology can play an important role in budget-based payment programmes and should expect to participate as full gainsharing partners. Precise costing methodologies and accurate economic modelling, along with identification of quality management and cost control opportunities, will help identify participation opportunities and appropriate payment and gainsharing agreements. Anaesthesiology-specific examples with budget-based payment models are needed to help guide increased participation in these programmes.

Regulatory activity based risk model identifies survival of stage II and III colorectal carcinoma.

Science.gov (United States)

Liu, Gang; Dong, Chuanpeng; Wang, Xing; Hou, Guojun; Zheng, Yu; Xu, Huilin; Zhan, Xiaohui; Liu, Lei

2017-11-17

Clinical and pathological indicators are inadequate for prognosis of stage II and III colorectal carcinoma (CRC). In this study, we utilized the activity of regulatory factors, univariate Cox regression and random forest for variable selection and developed a multivariate Cox model to predict the overall survival of Stage II/III colorectal carcinoma in GSE39582 datasets (469 samples). Patients in low-risk group showed a significant longer overall survival and recurrence-free survival time than those in high-risk group. This finding was further validated in five other independent datasets (GSE14333, GSE17536, GSE17537, GSE33113, and GSE37892). Besides, associations between clinicopathological information and risk score were analyzed. A nomogram including risk score was plotted to facilitate the utilization of risk score. The risk score model is also demonstrated to be effective on predicting both overall and recurrence-free survival of chemotherapy received patients. After performing Gene Set Enrichment Analysis (GSEA) between high and low risk groups, we found that several cell-cell interaction KEGG pathways were identified. Funnel plot results showed that there was no publication bias in these datasets. In summary, by utilizing the regulatory activity in stage II and III colorectal carcinoma, the risk score successfully predicts the survival of 1021 stage II/III CRC patients in six independent datasets.

An Investigation of the Repair Cycle for H-53 and H-60 Helicopter Main Gearboxes - Physical Movement and Information Flows

Science.gov (United States)

1989-09-01

15 The Pipeline . . 17 The Repair Cycle 20 The Order Cycle ard Order Processing 24 Summary . . . . . . . . . . . 27 III. Methodology...cycles, and order processing . The literature is found in business logistics books, business logistics periodicals, and military periodicals. 14 II...differences and problems previously outlined (1:19). The Order Cycle and Order Processing The Nature of the Order Cycle and Order Processing . Order

Synthesis and characterization of La(III), Pr(III), Nd(III), Sm(III), Eu(III), Gd(III), Tb(III) and Dy(III) complexes of 2-acetylfuran-2-thenoylhydrazone

International Nuclear Information System (INIS)

Singh, B.; Singh, Praveen K.

1998-01-01

The reaction of 2-acetylfuran-2-thenoylhydrazone(afth) with Ln(III) trichlorides yields complexes of the type [Ln(afth)Cl 2 (H 2 O)(EtOH)]Cl, [Ln(III) = La, Pr, Nd, Sm, Eu, Gd, Tb and Dy]. The complexes have been characterized by molar conductance, magnetic susceptibility and TGA and DTA measurements, magnetic susceptibility and TGA and DTA measurements, FAB mass, infrared, proton NMR, electronic absorption and emission spectra. The terbium complex is found to be monomer from the FAB mass spectrum. The IR and NMR spectra suggest neutral tridentate behaviour of the Schiff base. A coordination number seven is proposed around the metal ions. Emission spectra suggest C 3v , symmetry around the metal ion with capped octahedron geometry for the europium complex. (author)

Biofuels: Project summaries

Energy Technology Data Exchange (ETDEWEB)

1994-07-01

The US DOE, through the Biofuels Systems Division (BSD) is addressing the issues surrounding US vulnerability to petroleum supply. The BSD goal is to develop technologies that are competitive with fossil fuels, in both cost and environmental performance, by the end of the decade. This document contains summaries of ongoing research sponsored by the DOE BSD. A summary sheet is presented for each project funded or in existence during FY 1993. Each summary sheet contains and account of project funding, objectives, accomplishments and current status, and significant publications.

Preparation and characterisation of mixed ligand complexes of Co(III), Fe(III) and Cr(III) containing phthalimide and phenols

International Nuclear Information System (INIS)

Miah, M.A.J.; Islam, M.S.; Pal, S.C.; Barma, T.K.

1996-01-01

Some novel mixed ligand complexes of Co(III), Fe(III) and Cr(III) containing phthalimide as primary and 2-aminophenol and 3-aminophenol as secondary ligands have been synthesized and characterised on the basis of elemental analyses, conductivity and magnetic measurements and infrared and electronic spectral studies. Complexes containing 2-aminophenol are 1:1 electrolyte in N,N dimethylformamide. Spectral studies indicate that all the complexes exhibit octahedral geometry. The complexes have the general composition; K[M(pim)/sub 2/(L)/sub 2/]; where m=Co(III), Fe(III) and Cr(III), pim-anion of phthalimamide and L=anion of 2-aminophenol and 3-aminophenol. (author)

Combined effects of Lanthanum(III) and elevated Ultraviolet-B radiation on root nitrogen nutrient in soybean seedlings.

Science.gov (United States)

Huang, Guangrong; Wang, Lihong; Sun, Zhaoguo; Li, Xiaodong; Zhou, Qing; Huang, Xiaohua

2015-02-01

Rare earth element pollution and elevated ultraviolet-B (UV-B) radiation occur simultaneously in some regions, but the combined effects of these two factors on plants have not attracted enough attention. Nitrogen nutrient is vital to plant growth. In this study, the combined effects of lanthanum(III) and elevated UV-B radiation on nitrate reduction and ammonia assimilation in soybean (Glycine max L.) roots were investigated. Treatment with 0.08 mmol L(-1) La(III) did not change the effects of elevated UV-B radiation on nitrate reductase (NR), nitrite reductase (NiR), glutamine synthetase (GS), glutamate synthase (GOGAT), glutamate dehydrogenase (GDH), nitrate, ammonium, amino acids, or soluble protein in the roots. Treatment with 0.24 mmol L(-1) La(III) and elevated UV-B radiation synergistically decreased the NR, NiR, GS, and GOGAT activities as well as the nitrate, amino acid, and soluble protein levels, except for the GDH activity and ammonium content. Combined treatment with 1.20 mmol L(-1) La(III) and elevated UV-B radiation produced severely deleterious effects on all test indices, and these effects were stronger than those induced by La(III) or elevated UV-B radiation treatment alone. Following the withdrawal of La(III) and elevated UV-B radiation, all test indices for the combined treatments with 0.08/0.24 mmol L(-1) La(III) and elevated UV-B radiation recovered to a certain extent, but they could not recover for treatments with 1.20 mmol L(-1) La(III) and elevated UV-B radiation. In summary, combined treatment with La(III) and elevated UV-B radiation seriously affected nitrogen nutrition in soybean roots through the inhibition of nitrate reduction and ammonia assimilation.

Overview and summary

International Nuclear Information System (INIS)

1999-01-01

The ITER Physics Basis presents and evaluates the physics rules and methodologies for plasma performance projections, which provide the basis for the design of a tokamak burning plasma device whose goal is to demonstrate the scientific and technological feasibility of fusion energy for peaceful purposes. This Chapter summarizes the physics basis for burning plasma projections, which is developed in detail by the ITER Physics Expert Groups in subsequent chapters. To set context, the design guidelines and requirements established in the report of ITER Special Working Group 1 are presented, as are the specifics of the tokamak design developed in the Final Design Report of the ITER Engineering Design Activities, which exemplifies burning tokamak plasma experiments. The behaviour of a tokamak plasma is determined by the interaction of many diverse physics processes, all of which bear on projections for both a burning plasma experiment and an eventual tokamak reactor. Key processes summarized here are energy and particle confinement and the H-mode power threshold; MHD stability, including pressure and density limits, neoclassical islands, error fields, disruptions, sawteeth, and ELMs; power and particle exhaust, involving divertor power dispersal, helium exhaust, fuelling and density control, H-mode edge transition region, erosion of plasma facing components, tritium retention; energetic particle physics; auxiliary power physics; and the physics of plasma diagnostics. Summaries of projection methodologies, together with estimates of their attendant uncertainties, are presented in each of these areas. Since each physics element has its own scaling properties, an integrated experimental demonstration of the balance between the combined processes which obtains in a reactor plasma is inaccessible to contemporary experimental facilities: it requires a reactor scale device. It is argued, moreover, that a burning plasma experiment can be sufficiently flexible to permit

SKB annual report 1993. Including summaries of technical reports issued during 1993

International Nuclear Information System (INIS)

1994-05-01

This is the annual report on the activities of the Swedish Nuclear and Waste Management Co., SKB. It contains in part I an overview of SKB activities in different fields. Part II gives a description of the research and development work on nuclear waste disposal performed during 1993. Lectures and publications during 1993 as well as reports issued in the SKB technical series are listed in part III. Part IV contains the summaries of all technical reports issued during 1993. SKB is the owner of CLAB, the Central Facility for Interim Storage of Spent Nuclear Fuel, located at Oskarshamn. CLAB was taken into operation in July 1985 and to the end of 1993 in total 1 885 tonnes of spent fuel (measured as uranium) have been received. Transportation from the nuclear sites to CLAB is made by a special ship, M/S Sigyn. At Forsmark the final repository for Radioactive Waste - SFR - was taken into operation in April 1988. The repository is situated in crystalline rock under the Baltic Sea. At the end of 1993 a total of 13 000 m 3 of waste have been deposited in SFR. SKB is in charge of a comprehensive research and development programme on geological disposal of nuclear waste. Some of the main areas for SKB research are: Groundwater movements; Bedrock stability; Groundwater chemistry and nuclide migration; Methods and instruments for in situ characterization of crystalline bedrock; Characterization and leaching of spent nuclear fuel; Properties of bentonite for buffer, backfilling and sealing; Radionuclide transport in biosphere and dose evaluations; Development of performance and safety assessment methodology and assessment models; Construction of an underground research laboratory

The Uses of Mass Communications: Current Perspectives on Gratifications Research. Sage Annual Reviews of Communication Research Volume III.

Science.gov (United States)

Blumler, Jay G., Ed.; Katz, Elihu, Ed.

The essays in this volume examine the use of the mass media and explore the findings of the gratifications approach to mass communication research. Part one summaries the achievements in this area of mass media research and proposes an agenda for discussion of the future direction of this research in terms of a set of theoretical, methodological,…

76 FR 12985 - Request for Comments on Trend Factor Methodology Used in the Calculation of Fair Market Rents

Science.gov (United States)

2011-03-09

... Trend Factor Methodology Used in the Calculation of Fair Market Rents AGENCY: Office of the Assistant... used to calculate the trend factor component of the Fair Market Rent estimates. SUMMARY: Section 8(c)(1... comment regarding the manner in which HUD calculates the trend factor used in the Fair Market Rent (FMR...

CSNI Status summary on utilization of best-estimate methodology in safety analysis and licensing

International Nuclear Information System (INIS)

1996-10-01

The PWG 2 Task Group on Thermal Hydraulic System Behavior has discussed the subject of the use of best-estimate codes in the licensing process (codes that model thermal hydraulic processes are important to assessing safety system performance). The Task Group set out to determine the prevailing practices in member countries, concerning safety assessment and safety review of transients affecting the reactor coolant system. A summary of information provided by member countries in response to eleven questions is given: Who is Responsible for Safety Analysis? Who is Responsible for Review and Evaluation of Safety Analysis? Do the Regulations Permit the use of Best-Estimate Codes? What are the Requirements for What Constitutes a Best Estimate Code? What are the Requirements Concerning Code Documentation? What are the Requirements for Review of Code Models and Correlations? What are the Requirements Concerning Code Assessment? What are the Requirements Concerning Initial and Boundary Conditions? What are the Requirements Concerning Operability of Active Equipment? What are the Requirements Concerning Operator Actions?

WAIS-III index score profiles in the Canadian standardization sample.

Science.gov (United States)

Lange, Rael T

2007-01-01

Representative index score profiles were examined in the Canadian standardization sample of the Wechsler Adult Intelligence Scale-Third Edition (WAIS-III). The identification of profile patterns was based on the methodology proposed by Lange, Iverson, Senior, and Chelune (2002) that aims to maximize the influence of profile shape and minimize the influence of profile magnitude on the cluster solution. A two-step cluster analysis procedure was used (i.e., hierarchical and k-means analyses). Cluster analysis of the four index scores (i.e., Verbal Comprehension [VCI], Perceptual Organization [POI], Working Memory [WMI], Processing Speed [PSI]) identified six profiles in this sample. Profiles were differentiated by pattern of performance and were primarily characterized as (a) high VCI/POI, low WMI/PSI, (b) low VCI/POI, high WMI/PSI, (c) high PSI, (d) low PSI, (e) high VCI/WMI, low POI/PSI, and (f) low VCI, high POI. These profiles are potentially useful for determining whether a patient's WAIS-III performance is unusual in a normal population.

Assessing Built Environment Walkability using Activity-Space Summary Measures.

Science.gov (United States)

Tribby, Calvin P; Miller, Harvey J; Brown, Barbara B; Werner, Carol M; Smith, Ken R

There is increasing emphasis on active transportation, such as walking, in transportation planning as a sustainable form of mobility and in public health as a means of achieving recommended physical activity and better health outcomes. A research focus is the influence of the built environment on walking, with the ultimate goal of identifying environmental modifications that invite more walking. However, assessments of the built environment for walkability are typically at a spatially disaggregate level (such as street blocks) or at a spatially aggregate level (such as census block groups). A key issue is determining the spatial units for walkability measures so that they reflect potential walking behavior. This paper develops methods for assessing walkability within individual activity spaces : the geographic region accessible to an individual during a given walking trip. We first estimate street network-based activity spaces using the shortest path between known trip starting/ending points and a travel time budget that reflects potential alternative paths. Based on objective walkability measures of the street blocks, we use three summary measures for walkability within activity spaces: i) the average walkability score across block segments (representing the general level of walkability in the activity space); ii) the standard deviation (representing the walkability variation), and; iii) the network autocorrelation (representing the spatial coherence of the walkability pattern). We assess the method using data from an empirical study of built environment walkability and walking behavior in Salt Lake City, Utah, USA. We visualize and map these activity space summary measures to compare walkability among individuals' trips within their neighborhoods. We also compare summary measures for activity spaces versus census block groups, with the result that they agree less than half of the time.

Validation of the Serpent 2-DYNSUB code sequence using the Special Power Excursion Reactor Test III (SPERT III)

International Nuclear Information System (INIS)

Knebel, Miriam; Mercatali, Luigi; Sanchez, Victor; Stieglitz, Robert; Macian-Juan, Rafael

2016-01-01

Highlights: • Full few-group cross section tables created by Monte Carlo lattice code Serpent 2. • Serpent 2 group constant methodology verified for HFP static and transient cases. • Serpent 2-DYNSUB tool chainvalidated using SPERT III REA experiments. • Serpent 2-DYNSUB tool chain suitable to model RIAs in PWRs. - Abstract: The Special Power Excursion Reactor Test III (SPERT III) is studied using the Serpent 2-DYNSUB code sequence in order to validate it for modeling reactivity insertion accidents (RIA) in PWRs. The SPERT III E-core was a thermal research reactor constructed to analyze reactor dynamics. Its configuration resembles a commercial PWR on terms of fuel type, choice of moderator, coolant flow and system pressure. The initial conditions of the rod ejection accident experiments (REA) performed cover cold startup, hot startup, hot standby and operating power scenarios. Eight of these experiments were analyzed in detail. Firstly, multi-dimensional nodal diffusion cross section tables were created for the three-dimensional reactor simulator DYNSUB employing the Monte Carlo neutron transport code Serpent 2. In a second step, DYNSUB stationary simulations were compared to Monte Carlo reference three-dimensional full scale solutions obtained with Serpent 2 (cold startup conditions) and Serpent 2/SUBCHANFLOW (operating power conditions) with a good agreement being observed. The latter tool is an internal coupling of Serpent 2 and the sub-channel thermal-hydraulics code SUBCHANFLOW. Finally, DYNSUB was utilized to study the eight selected transient experiments. Results were found to match measurements well. As the selected experiments cover much of the possible transient (delayed super-critical, prompt super-critical and super-prompt critical excursion) and initial conditions (cold and hot as well as zero, little and full power reactor states) one expects in commercial PWRs, the obtained results give confidence that the Serpent 2-DYNSUB tool chain is

An Independent Scientific Assessment of Well Stimulation in California Volume III

Energy Technology Data Exchange (ETDEWEB)

Long, Jane C.S. [California Council on Science and Technology, Sacramento, CA (United States); Feinstein, Laura C. [California Council on Science and Technology, Sacramento, CA (United States); Birkholzer, Jens [California Council on Science and Technology, Sacramento, CA (United States); Foxall, William [California Council on Science and Technology, Sacramento, CA (United States); Houseworth, James [California Council on Science and Technology, Sacramento, CA (United States); Jordan, Preston [California Council on Science and Technology, Sacramento, CA (United States); Lindsey, Nathaniel [California Council on Science and Technology, Sacramento, CA (United States); Maddalena, Randy [California Council on Science and Technology, Sacramento, CA (United States); McKone, Thomas [California Council on Science and Technology, Sacramento, CA (United States); Stringfellow, William [California Council on Science and Technology, Sacramento, CA (United States); Ulrich, Craig [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Heberger, Matthew [Pacific Inst., Oakland, CA (United States); Shonkoff, Seth [PSE Healthy Energy, Berkeley, CA (United States); Brandt, Adam [Stanford Univ., CA (United States); Ferrar, Kyle [The FracTracker Alliance, Oakland, CA (United States); Gautier, Donald [DonGautier LLC., Palo Alto, CA (United States); Phillips, Scott [California State Univ. Stanislaus, Turlock, CA (United States); Greenfield, Ben [Univ. of California, Berkeley, CA (United States); Jerrett, Michael L.B. [Univ. of California, Los Angeles, CA (United States)

2015-07-01

This study is issued in three volumes. Volume I, issued in January 2015, describes how well stimulation technologies work, how and where operators deploy these technologies for oil and gas production in California, and where they might enable production in the future. Volume II, issued in July 2015, discusses how well stimulation could affect water, atmosphere, seismic activity, wildlife and vegetation, and human health. Volume II reviews available data, and identifies knowledge gaps and alternative practices that could avoid or mitigate these possible impacts. Volume III, this volume, presents case studies that assess environmental issues and qualitative risks for specific geographic regions. The Summary Report summarizes key findings, conclusions and recommendations of all three volumes.

Methodologies for Quantitative Systems Pharmacology (QSP) Models: Design and Estimation.

Science.gov (United States)

Ribba, B; Grimm, H P; Agoram, B; Davies, M R; Gadkar, K; Niederer, S; van Riel, N; Timmis, J; van der Graaf, P H

2017-08-01

With the increased interest in the application of quantitative systems pharmacology (QSP) models within medicine research and development, there is an increasing need to formalize model development and verification aspects. In February 2016, a workshop was held at Roche Pharma Research and Early Development to focus discussions on two critical methodological aspects of QSP model development: optimal structural granularity and parameter estimation. We here report in a perspective article a summary of presentations and discussions. © 2017 The Authors CPT: Pharmacometrics & Systems Pharmacology published by Wiley Periodicals, Inc. on behalf of American Society for Clinical Pharmacology and Therapeutics.

Comparison between dispersed nuclear power plants and a nuclear energy center at a hypothetical site on Kentucky Lake, Tennessee. Volume I. Summary

International Nuclear Information System (INIS)

Burwell, C.C.; Reister, D.B.; Rosemarin, C.S.; Sisman, O.; Suffern, J.S.

1976-05-01

A brief summary is presented of the surrogate site concept used to compare the Nuclear Energy Center (NEC) concept with the present method of dispersed siting of nuclear power plants. Included are data on power transmission, environmental considerations, and a discussion of a site selection methodology

Thermodynamic data for predicting concentrations of Pu(III), Am(III), and Cm(III) in geologic environments

Energy Technology Data Exchange (ETDEWEB)

Rai, Dhanpat; Rao, Linfeng; Weger, H.T.; Felmy, A.R. [Pacific Northwest National Laboratory, WA (United States); Choppin, G.R. [Florida State University, Florida (United States); Yui, Mikazu [Japan Nuclear Cycle Development Inst., Tokai Works, Tokai, Ibaraki (Japan)

1999-01-01

This report provides thermodynamic data for predicting concentrations of Pu(III), Am(III), and Cm(III) in geologic environments, and contributes to an integration of the JNC chemical thermodynamic database, JNC-TDB (previously PNC-TDB), for the performance analysis of geological isolation system for high-level radioactive wastes. Thermodynamic data for the formation of complexes or compounds with hydroxide, chloride, fluoride, carbonate, nitrate, sulfate and phosphate are discussed in this report. Where data for specific actinide(III) species are lacking, the data were selected based on chemical analogy to other trivalent actinides. In this study, the Pitzer ion-interaction model is mainly used to extrapolate thermodynamic constants to zero ionic strength at 25degC. (author)

Luminescence study on solvation of americium(III), curium(III) and several lanthanide(III) ions in nonaqueous and binary mixed solvents

International Nuclear Information System (INIS)

Kimura, T.; Nagaishi, R.; Kato, Y.; Yoshida, Z.

2001-01-01

The luminescence lifetimes of An(III) and Ln(III) ions [An=Am and Cm; Ln=Nd, Sm, Eu, Tb and Dy] were measured in dimethyl sulfoxide(DMSO), N,N-dimethylformamide(DMF), methanol(MeOH), water and their perdeuterated solvents. Nonradiative decay rates of the ions were in the order of H 2 O > MeOH > DMF > DMSO, indicating that O-H vibration is more effective quencher than C-H, C=O, and S=O vibrations in the solvent molecules. Maximal lifetime ratios τ D /τ H were observed for Eu(III) in H 2 O, for Sm(III) in MeOH and DMF, and for Sm(III) and Dy(III) in DMSO. The solvent composition in the first coordination sphere of Cm(III) and Ln(III) in binary mixed solvents was also studied by measuring the luminescence lifetime. Cm(III) and Ln(III) were preferentially solvated by DMSO in DMSO-H 2 O, by DMF in DMF-H 2 O, and by H 2 O in MeOH-H 2 O over the whole range of the solvent composition. The order of the preferential solvation, i.e., DMSO > DMF > H 2 O > MeOH, correlates with the relative basicity of these solvents. The Gibbs free energy of transfer of ions from water to nonaqueous solvents was further estimated from the degree of the preferential solvation. (orig.)

Luminescence studies of Sm(III) and Cm(III) complexes in NaSCN/DHDECMP extraction systems

CERN Document Server

Chung, D Y; Kimura, T

1999-01-01

Laser-induced fluorescence (LIF) studies of Sm(III) and Cm(III) complexes in the NaSCN/DHDECMP solvent extraction system were carried out. Luminescence lifetimes were measured to determine the number of water molecules coordinated to Sm(III), Tb(III), Dy(III), and Cm(III) in the sodium thiocyanate solution and in the DHDECMP phase. The hydration number of Sm(III), Tb(III), Dy(III), and Cm(III) in the sodium thiocyanate solution decreased linearly with increasing sodium thiocyanate concentration. The hydration numbers of Sm(III), Dy(III), and Cm(III) in the DHDECMP phase decreased with increasing sodium thiocyanate concentration. The water molecules in the inner coordination sphere of Sm(III) and Dy(III) extracted into the DHDECMP were not completely removed at low sodium thiocyanate concentration but decreased with increasing sodium thiocyanate concentration. However, in the case of Cm(III) extracted into the DHDECMP phase from the sodium thiocyanate solution, there was no water in the inner coordination sphe...

Enhancer SINEs Link Pol III to Pol II Transcription in Neurons

Directory of Open Access Journals (Sweden)

Cristina Policarpi

2017-12-01

Full Text Available Summary: Spatiotemporal regulation of gene expression depends on the cooperation of multiple mechanisms, including the functional interaction of promoters with distally located enhancers. Here, we show that, in cortical neurons, a subset of short interspersed nuclear elements (SINEs located in the proximity of activity-regulated genes bears features of enhancers. Enhancer SINEs (eSINEs recruit the Pol III cofactor complex TFIIIC in a stimulus-dependent manner and are transcribed by Pol III in response to neuronal depolarization. Characterization of an eSINE located in proximity to the Fos gene (FosRSINE1 indicated that the FosRSINE1-encoded transcript interacts with Pol II at the Fos promoter and mediates Fos relocation to Pol II factories, providing an unprecedented molecular link between Pol III and Pol II transcription. Strikingly, knockdown of the FosRSINE1 transcript induces defects of both cortical radial migration in vivo and activity-dependent dendritogenesis in vitro, demonstrating that FosRSINE1 acts as a strong enhancer of Fos expression in diverse physiological contexts. : Spatiotemporal regulation of gene expression requires the interaction between promoters and distally located enhancers. Policarpi et al. identify a subset of SINEs that functions as enhancers for activity-dependent neuronal genes. The enhancer SINE FosRSINE1 regulates Fos transcription and is necessary for both activity-dependent dendritogenesis and proper brain development. Keywords: neuroscience, epigenetics, transcription, enhancers, SINEs, neuronal activity, neuronal development

Summary big data

CERN Document Server

2014-01-01

This work offers a summary of Cukier the book: "Big Data: A Revolution That Will Transform How we Live, Work, and Think" by Viktor Mayer-Schonberg and Kenneth. Summary of the ideas in Viktor Mayer-Schonberg's and Kenneth Cukier's book: " Big Data " explains that big data is where we use huge quantities of data to make better predictions based on the fact we identify patters in the data rather than trying to understand the underlying causes in more detail. This summary highlights that big data will be a source of new economic value and innovation in the future. Moreover, it shows that it will

Summary information report

International Nuclear Information System (INIS)

1982-07-01

The Summary Information Report (SIR) provides summary data concerning NRC and its licensees for general use by the Chairman, other Commissioners and Commission staff offices, the Executive Director for Operations, and the Office Directors. SIR is published quarterly by the Management Information Branch (49-27834) of the Office of Resource Management

Challenges and Opportunities for Harmonizing Research Methodology: Raw Accelerometry.

Science.gov (United States)

van Hees, Vincent T; Thaler-Kall, Kathrin; Wolf, Klaus-Hendrik; Brønd, Jan C; Bonomi, Alberto; Schulze, Mareike; Vigl, Matthäus; Morseth, Bente; Hopstock, Laila Arnesdatter; Gorzelniak, Lukas; Schulz, Holger; Brage, Søren; Horsch, Alexander

2016-12-07

Raw accelerometry is increasingly being used in physical activity research, but diversity in sensor design, attachment and signal processing challenges the comparability of research results. Therefore, efforts are needed to harmonize the methodology. In this article we reflect on how increased methodological harmonization may be achieved. The authors of this work convened for a two-day workshop (March 2014) themed on methodological harmonization of raw accelerometry. The discussions at the workshop were used as a basis for this review. Key stakeholders were identified as manufacturers, method developers, method users (application), publishers, and funders. To facilitate methodological harmonization in raw accelerometry the following action points were proposed: i) Manufacturers are encouraged to provide a detailed specification of their sensors, ii) Each fundamental step of algorithms for processing raw accelerometer data should be documented, and ideally also motivated, to facilitate interpretation and discussion, iii) Algorithm developers and method users should be open about uncertainties in the description of data and the uncertainty of the inference itself, iv) All new algorithms which are pitched as "ready for implementation" should be shared with the community to facilitate replication and ongoing evaluation by independent groups, and v) A dynamic interaction between method stakeholders should be encouraged to facilitate a well-informed harmonization process. The workshop led to the identification of a number of opportunities for harmonizing methodological practice. The discussion as well as the practical checklists proposed in this review should provide guidance for stakeholders on how to contribute to increased harmonization.

Association of Eu(III) and Cm(III) with Bacillus subtilis and Halobacterium salinarum

International Nuclear Information System (INIS)

Ozaki, Takuo; Kimura, Takaumi; Ohnuki, Toshihiko; Yoshida, Zenko

2002-01-01

Adsorption behavior of Eu(III) and Cm(III) by Bacillus subtilis and Halobacterium salinarum was investigated. Both microorganisms showed almost identical pH dependence on the distribution ratio (K d ) of the metals examined, i.e., K d of Eu(III) and Cm(III) increased with an increase of pH. The coordination state of Eu(III) adsorbed on the microorganisms was studied by time-resolved laser-induced fluorescence spectroscopy (TRLFS). The coordination states of Eu(III) adsorbed on the B. subtilis and H. salinarum was of different characteristics. H. salinarum exhibited more outer-spherical interaction with Eu(III) than B. subtilis. (author)

High-Penetration Photovoltaic Planning Methodologies

Energy Technology Data Exchange (ETDEWEB)

Gao, David Wenzhong [Alternative Power Innovations, LLC, Broomfield, CO (United States); Muljadi, Eduard [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tian, Tian [National Renewable Energy Lab. (NREL), Golden, CO (United States); Miller, Mackay [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-02-24

The main objective of this report is to provide an overview of select U.S. utility methodologies for performing high-penetration photovoltaic (HPPV) system planning and impact studies. This report covers the Federal Energy Regulatory Commission's orders related to photovoltaic (PV) power system interconnection, particularly the interconnection processes for the Large Generation Interconnection Procedures and Small Generation Interconnection Procedures. In addition, it includes U.S. state interconnection standards and procedures. The procedures used by these regulatory bodies consider the impacts of HPPV power plants on the networks. Technical interconnection requirements for HPPV voltage regulation include aspects of power monitoring, grounding, synchronization, connection to the overall distribution system, back-feeds, disconnecting means, abnormal operating conditions, and power quality. This report provides a summary of mitigation strategies to minimize the impact of HPPV. Recommendations and revisions to the standards may take place as the penetration level of renewables on the grid increases and new technologies develop in future years.

Evaluation methodology for tariff design under escalating penetrations of distributed energy resources

OpenAIRE

Abdelmotteleb, I.I.A.; Gómez, Tomás; Reneses, Javier

2017-01-01

As the penetration of distributed energy resources (DERs) escalates in distribution networks, new network tariffs are needed to cope with this new situation. These tariffs should allocate network costs to users, promoting an efficient use of the distribution network. This paper proposes a methodology to evaluate and compare network tariff designs. Four design attributes are proposed for this aim: (i) network cost recovery; (ii) deferral of network reinforcements; (iii) efficient consumer resp...

A workshop on developing risk assessment methods for medical use of radioactive material. Volume 1: Summary

Energy Technology Data Exchange (ETDEWEB)

Tortorelli, J.P. [ed.] [Lockheed Idaho Technologies Co., Idaho Falls, ID (United States)

1995-08-01

A workshop was held at the Idaho National Engineering Laboratory, August 16--18, 1994 on the topic of risk assessment on medical devices that use radioactive isotopes. Its purpose was to review past efforts to develop a risk assessment methodology to evaluate these devices, and to develop a program plan and a scoping document for future methodology development. This report contains a summary of that workshop. Participants included experts in the fields of radiation oncology, medical physics, risk assessment, human-error analysis, and human factors. Staff from the US Nuclear Regulatory Commission (NRC) associated with the regulation of medical uses of radioactive materials and with research into risk-assessment methods participated in the workshop. The workshop participants concurred in NRC`s intended use of risk assessment as an important technology in the development of regulations for the medical use of radioactive material and encouraged the NRC to proceed rapidly with a pilot study. Specific recommendations are included in the executive summary and the body of this report. An appendix contains the 8 papers presented at the conference: NRC proposed policy statement on the use of probabilistic risk assessment methods in nuclear regulatory activities; NRC proposed agency-wide implementation plan for probabilistic risk assessment; Risk evaluation of high dose rate remote afterloading brachytherapy at a large research/teaching institution; The pros and cons of using human reliability analysis techniques to analyze misadministration events; Review of medical misadministration event summaries and comparison of human error modeling; Preliminary examples of the development of error influences and effects diagrams to analyze medical misadministration events; Brachytherapy risk assessment program plan; and Principles of brachytherapy quality assurance.

A workshop on developing risk assessment methods for medical use of radioactive material. Volume 1: Summary

International Nuclear Information System (INIS)

Tortorelli, J.P.

1995-08-01

A workshop was held at the Idaho National Engineering Laboratory, August 16--18, 1994 on the topic of risk assessment on medical devices that use radioactive isotopes. Its purpose was to review past efforts to develop a risk assessment methodology to evaluate these devices, and to develop a program plan and a scoping document for future methodology development. This report contains a summary of that workshop. Participants included experts in the fields of radiation oncology, medical physics, risk assessment, human-error analysis, and human factors. Staff from the US Nuclear Regulatory Commission (NRC) associated with the regulation of medical uses of radioactive materials and with research into risk-assessment methods participated in the workshop. The workshop participants concurred in NRC's intended use of risk assessment as an important technology in the development of regulations for the medical use of radioactive material and encouraged the NRC to proceed rapidly with a pilot study. Specific recommendations are included in the executive summary and the body of this report. An appendix contains the 8 papers presented at the conference: NRC proposed policy statement on the use of probabilistic risk assessment methods in nuclear regulatory activities; NRC proposed agency-wide implementation plan for probabilistic risk assessment; Risk evaluation of high dose rate remote afterloading brachytherapy at a large research/teaching institution; The pros and cons of using human reliability analysis techniques to analyze misadministration events; Review of medical misadministration event summaries and comparison of human error modeling; Preliminary examples of the development of error influences and effects diagrams to analyze medical misadministration events; Brachytherapy risk assessment program plan; and Principles of brachytherapy quality assurance

40 CFR 1502.12 - Summary.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Summary. 1502.12 Section 1502.12 Protection of Environment COUNCIL ON ENVIRONMENTAL QUALITY ENVIRONMENTAL IMPACT STATEMENT § 1502.12 Summary. Each environmental impact statement shall contain a summary which adequately and accurately summarizes...

Sorption of small amounts of europium(III) on iron(III) hydroxide and oxide

International Nuclear Information System (INIS)

Music, S.; Gessner, M.; Wolf, R.H.H.

1979-01-01

The sorption of small amounts of europium(III) on iron(III) hydroxide and oxide has been studied as a function of pH. The mechanism of sorption is discussed. Optimum conditions have been found for the preconcentration of small or trace amounts of europium(III) by iron(III) hydroxide and oxide. The influence of complexing agents (EDTA, oxalate, tartrate and 5-sulfosalicylic acid) on the sorption of small amounts of europium(III) on iron(III) oxide has also been studied. (author)

Integration of an iterative methodology for exergoeconomic improvement of thermal systems with a process simulator

International Nuclear Information System (INIS)

Vieira, Leonardo S.; Donatelli, Joao L.; Cruz, Manuel E.

2004-01-01

In this paper, we present the development and automated implementation of an iterative methodology for exergoeconomic improvement of thermal systems integrated with a process simulator, so as to be applicable to real, complex plants. The methodology combines recent available exergoeconomic techniques with new qualitative and quantitative criteria for the following tasks: (i) identification of decision variables that affect system total cost and exergetic efficiency; (ii) hierarchical classification of components; (iii) identification of predominant terms in the component total cost; and (iv) choice of main decision variables in the iterative process. To show the strengths and potential advantages of the proposed methodology, it is here applied to the benchmark CGAM cogeneration system. The results obtained are presented and discussed in detail and are compared to those reached using a mathematical optimization procedure

Extending statistical boosting. An overview of recent methodological developments.

Science.gov (United States)

Mayr, A; Binder, H; Gefeller, O; Schmid, M

2014-01-01

Boosting algorithms to simultaneously estimate and select predictor effects in statistical models have gained substantial interest during the last decade. This review highlights recent methodological developments regarding boosting algorithms for statistical modelling especially focusing on topics relevant for biomedical research. We suggest a unified framework for gradient boosting and likelihood-based boosting (statistical boosting) which have been addressed separately in the literature up to now. The methodological developments on statistical boosting during the last ten years can be grouped into three different lines of research: i) efforts to ensure variable selection leading to sparser models, ii) developments regarding different types of predictor effects and how to choose them, iii) approaches to extend the statistical boosting framework to new regression settings. Statistical boosting algorithms have been adapted to carry out unbiased variable selection and automated model choice during the fitting process and can nowadays be applied in almost any regression setting in combination with a large amount of different types of predictor effects.

Inventory of Federal energy-related environment and safety research for FY 1978. Volume 1. Executive summary

International Nuclear Information System (INIS)

1979-12-01

The FY 1978 Federal Inventory is a compilation of 3225 federally funded energy-related environmental and safety reserch projects. It consists of three volumes: an executive summary providing an overview of the data (Volume I), a catalog listing each Inventory project followed by series of indexes (Volume II), and an interactive terminal guide giving instructions for on-line data retrieval (Volume III). Volume I reviews the inventory data as a whole and also within each of three major categories: biomedical and environmental research, environmental control technology research, and operational safety research

Stability of Tl(III) in the context of speciation analysis of thallium in plants.

Science.gov (United States)

Sadowska, Monika; Biaduń, Ewa; Krasnodębska-Ostręga, Beata

2016-02-01

The paper presents both "good" and "bad" results obtained during speciation analysis of thallium in plant tissues of a hyperaccumulator of this metal. The object was white mustard - Sinapis alba L. In this plant there were found traces of trivalent thallium. The crucial point of this study (especially in the case of so unstable thallium form as Tl(III)) was to prove that the presence of Tl(III) was not caused by the procedure of sample preparation itself, and that the whole analytical method provides reliable results. Choice of the method for conservation of the initial speciation, extraction with the highest efficiency and proving the correctness of the obtained data were the most difficult parts of the presented study. It was found that: both freezing and drying cause significant changes in the speciation of thallium; quantitative analysis could be performed only with fresh tissues of mustard plants; only short-term storage of an extract from fresh plant tissues is possible; the methodology is not the source of thallium (III); only the presence of DTPA can greatly limit the reduction of TI(III) to TI(I) (up to 1-3%); the UV irradiation results in disintegration of TI(III)DTPA in the presence of plant matrix (reduction up to 90%). Copyright © 2015 Elsevier Ltd. All rights reserved.

7 CFR 3402.12 - Project summary.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Project summary. 3402.12 Section 3402.12 Agriculture... FELLOWSHIP GRANTS PROGRAM Preparation of an Application § 3402.12 Project summary. Using the Project Summary.... The summary should not include any reference to the specific number of fellowships requested. The...

Perancangan Data Warehouse Nilai Mahasiswa Dengan Kimball Nine-Step Methodology

Directory of Open Access Journals (Sweden)

Ganda Wijaya

2017-04-01

Abstract Student grades has many components that can be analyzed to support decision making. Based on this, the authors conducted a study of student grades. The study was conducted on a database that is in the Bureau of Academic and Student Affairs Administration Bina Sarana Informatika (BAAK BSI. The focus of this research is "How to model a data warehouse that can meet the management needs of the data value of students as supporters of evaluation, planning and decision making?". Data warehouse grades students need to be made in order to obtain the information, reports, and can perform multi-dimensional analysis, which in turn can assist management in making policy. Development of the system is done by using System Development Life Cycle (SDLC with Waterfall approach. While the design of the data warehouse using a nine-step methodology kimball. Results obtained in the form of a star schema and data warehouse value. Data warehouses can provide a summary of information that is fast, accurate and continuous so as to assist management in making policies for the future. In general, the benefits of this research are as additional reference in building a data warehouse using a nine-step methodology kimball.   Keywords: Data Warehouse, Kimball Nine-Step Methodology.

49 CFR 194.113 - Information summary.

Science.gov (United States)

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Information summary. 194.113 Section 194.113... Response Plans § 194.113 Information summary. (a) The information summary for the core plan, required by... state(s). (b) The information summary for the response zone appendix, required in § 194.107, must...

Application of Decomposition Methodology to Solve Integrated Process Design and Controller Design Problems for Reactor-Separator-Recycle System

DEFF Research Database (Denmark)

Abd.Hamid, Mohd-Kamaruddin; Sin, Gürkan; Gani, Rafiqul

2010-01-01

This paper presents the integrated process design and controller design (IPDC) for a reactor-separator-recycle (RSR) system and evaluates a decomposition methodology to solve the IPDC problem. Accordingly, the IPDC problem is solved by decomposing it into four hierarchical stages: (i) pre...... the design of a RSR system involving consecutive reactions, A B -> C and shown to provide effective solutions that satisfy design, control and cost criteria. The advantage of the proposed methodology is that it is systematic, makes use of thermodynamic-process knowledge and provides valuable insights......-analysis, (ii) design analysis, (iii) controller design analysis, and (iv) final selection and verification. The methodology makes use of thermodynamic-process insights and the reverse design approach to arrive at the final process-controller design decisions. The developed methodology is illustrated through...

Advanced Experimental Analysis of Controls on Microbial Fe(III) Oxide Reduction - Final Report - 09/16/1996 - 03/16/2001; FINAL

International Nuclear Information System (INIS)

Roden, Eric E.

2001-01-01

Considering the broad influence that microbial Fe(III) oxide reduction can have on subsurface metal/organic contaminant biogeochemistry, understanding the mechanisms that control this process is critical for predicting the behavior and fate of these contaminants in anaerobic subsurface environments. Knowledge of the factors that influence the rates of growth and activity of Fe(III) oxide-reducing bacteria is critical for predicting (i.e., modeling) the long-term influence of these organisms on the fate of contaminants in the subsurface, and for effectively utilizing Fe(III) oxide reduction and associated geochemical affects for the purpose of subsurface metal/organic contamination bioremediation. This research project will refine existing models for microbiological and geochemical controls on Fe(III) oxide reduction, using laboratory reactor systems that mimic, to varying degrees, the physical and chemical conditions of the subsurface. Novel experimental methods for studying the kinetics of microbial Fe(III) oxide reduction and measuring growth rates of Fe(III) oxide-reducing bacteria will be developed. These new methodologies will be directly applicable to studies on subsurface contaminant transformations directly coupled to or influenced by microbial Fe(III) oxide reduction

Revision of Primary I-III Science Curriculum in Somalia. African Studies in Curriculum Development & Evaluation No. 83.

Science.gov (United States)

Abdi, Ahmed Ali

This study was designed to evaluate: (1) the content of the primary I-III science curriculum in Somalia; (2) the instructional materials that back up the content and methodologies; and (3) the professional competence of the teachers in charge of teaching this subject. Data were collected by means of a questionnaire, observations, and unstructured…

Effects upon metabolic pathways and energy production by Sb(III and As(III/Sb(III-oxidase gene aioA in Agrobacterium tumefaciens GW4.

Directory of Open Access Journals (Sweden)

Jingxin Li

Full Text Available Agrobacterium tumefaciens GW4 is a heterotrophic arsenite [As(III]/antimonite [Sb(III]-oxidizing strain. The As(III oxidase AioAB is responsible for As(III oxidation in the periplasm and it is also involved in Sb(III oxidation in Agrobacterium tumefaciens 5A. In addition, Sb(III oxidase AnoA and cellular H2O2 are also responsible for Sb(III oxidation in strain GW4. However, the deletion of aioA increased the Sb(III oxidation efficiency in strain GW4. In the present study, we found that the cell mobility to Sb(III, ATP and NADH contents and heat release were also increased by Sb(III and more significantly in the aioA mutant. Proteomics and transcriptional analyses showed that proteins/genes involved in Sb(III oxidation and resistance, stress responses, carbon metabolism, cell mobility, phosphonate and phosphinate metabolism, and amino acid and nucleotide metabolism were induced by Sb(III and were more significantly induced in the aioA mutant. The results suggested that Sb(III oxidation may produce energy. In addition, without periplasmic AioAB, more Sb(III would enter bacterial cells, however, the cytoplasmic AnoA and the oxidative stress response proteins were significantly up-regulated, which may contribute to the increased Sb(III oxidation efficiency. Moreover, the carbon metabolism was also activated to generate more energy against Sb(III stress. The generated energy may be used in Sb transportation, DNA repair, amino acid synthesis, and cell mobility, and may be released in the form of heat.

Progress report: The Energy and Industry Subgroup of IPCC Working Group III

International Nuclear Information System (INIS)

Yokobori, Keiichi

1990-01-01

The Intergovernmental Panel on Climate Change (IPCC) was established in November 1988 under the joint auspices of UNEP and the World Meteorological Organization (WMO). Working Group III, or the Response Strategies Working Group (RSWG), was established to formulate strategies to respond to challenges arising from global climate warming. The Energy and Industry Subgroup (EIS) was created by the RSWG at its meeting in January-February 1989 to facilitate the formulation of strategies to control, i.e. prevent or reduce, the accumulation of greenhouse gases (GHGs) such as CO 2 , CFCs, NO 2 , CH, etc. The following article gives a brief summary of EIS activities, based mainly on records of discussion at the relevant meetings. (author). 1 tab

Mixed ligand complexes of some of the rare earths. La(III)-, Pr(III)- or Nd-(III)-CDTA-Hydroxy Acids

Energy Technology Data Exchange (ETDEWEB)

Rana, H S; Tandon, J P [Rajasthan Univ., Jaipur (India). Chemical Labs.

1975-11-01

Biligand complexes of the 1:1 Ln(III)-1,2-diaminocyclohexane-tetraacetic acid (CDTA) chelate with hydroxy acids (where hydroxy acids = salicylic acid (SA); Sulphosalicylic acid (SSA) and 8-hydroxyquinoline-5-sulphonic acid (HQSA)) have been investigated by potentiometric titration. Their formation constants have been calculated (..mu..=0.1M-KNO/sub 3/; and t=30+-1 deg C) as 4.60 +-0.03, 5.46+-0.03, 5.87+-0.05; 3.12+-0.04, 3.95+-0.05, 4.42+-0.07; 2.73+-0.06, 3.45+-0.05 and 3.90+-0.08 for Ln(III)-CDTA-SA,-SSA, and -HQSA respectively (where Ln=La, Pr or Nd). The value of log Ksub(MAB) follows the order: La(III)).

Radioisotope methodology course radioprotection aspects

International Nuclear Information System (INIS)

Bergoc, R.M.; Caro, R.A.; Menossi, C.A.

1996-01-01

The advancement knowledge in molecular and cell biology, biochemistry, medicine and pharmacology, which has taken place during the last 50 years, after World War II finalization, is really outstanding. It can be safely said that this fact is principally due to the application of radioisotope techniques. The research on metabolisms, biodistribution of pharmaceuticals, pharmacodynamics, etc., is mostly carried out by means of techniques employing radioactive materials. Radioisotopes and radiation are frequently used in medicine both as diagnostic and therapeutic tools. The radioimmunoanalysis is today a routine method in endocrinology and in general clinical medicine. The receptor determination and characterization is a steadily growing methodology used in clinical biochemistry, pharmacology and medicine. The use of radiopharmaceuticals and radiation of different origins, for therapeutic purposes, should not be overlooked. For these reasons, the importance to teach radioisotope methodology is steadily growing. This is principally the case for specialization at the post-graduate level but at the pre graduate curriculum it is worthwhile to give some elementary theoretical and practical notions on this subject. These observations are justified by a more than 30 years teaching experience at both levels at the School of Pharmacy and Biochemistry of the University of Buenos Aires, Argentina. In 1960 we began to teach Physics III, an obligatory pregraduate course for biochemistry students, in which some elementary notions of radioactivity and measurement techniques were given. Successive modifications of the biochemistry pregraduate curriculum incorporated radiochemistry as an elective subject and since 1978, radioisotope methodology, as obligatory subject for biochemistry students. This subject is given at the radioisotope laboratory during the first semester of each year and its objective is to provide theoretical and practical knowledge to the biochemistry students, even

DECOVALEX - Mathematical models of coupled T-H-M processes for nuclear waste repositories. Report of phase III

International Nuclear Information System (INIS)

Jing, L.; Rutqvist, J.; Stephansson, O.

1995-12-01

This report presents the methodologies and results of the field/laboratory experiments and mathematical modeling defined for the phase III of the project. Results from test cases 2-6 are given in separate chapters of the report (which have been indexed separately), and the last chapter discusses the lessons learned from the three phases of the DECOVALEX project

Methodology for Determining the Avoidable and Fully Allocated Costs of Amtrak Routes : Volume III, Appendix B-H

Science.gov (United States)

2009-08-01

The Federal Railroad Administration tasked the Volpe Center with developing a methodology for determining the avoidable and fully allocated costs of Amtrak routes. Avoidable costs are costs that would not be incurred if an Amtrak route were discontin...

Enhancement of the fluorescence of the samarium (III) complex by gadolinium (III)

International Nuclear Information System (INIS)

Yun-Xiang, C.; Zhang-Hua, L.

1988-01-01

The increase in sensitivity and selectivity of reactions in which colored species are formed by the addition of different metal ions is an area of research that has recently been developed. This phenomenon, which is sometimes called cocolaration effect, has been explained by the formation of mixed metal complex. The authors found an analogous phenomenon of reactions forming fluorescent complexes. The complexes of Sm(III)-thenoyltrifluoroacetone (TTA)-phenanthroline (Phen)-Triton-X-100 (TX-100) and Gd(III) (or La(III), Lu(III) and Y(III))-TTA-Phen-TX-100 had practically no fluorescence separately. Instead, a fluorescence-enhancement phenomenon caused by adding Gd or La, Lu and Y ions to the system was observed for the first time. The intensity of the enhanced fluorescence of Sm(III) complex was increased in the following order: La< Y< Lu< Gd. By analogy with cocoloration effect, the authors call this new fluorescence-enhancement phenomenon the co-fluorescence effect. The object of this work was to study the enhancement effect of Gd(III) on the fluorescence of the Sm(III)-TTA-Phen-TX-100 system. The recommended fluorimetric method has been applied to the determination of trace amounts of samarium in ytterbium oxide with satisfactory results. A general reaction mechanism for the system studied was proposed

Intercultural education for citizenship in complex societies. Summary of the International Conference on Intercultural Education for citizenship.

Directory of Open Access Journals (Sweden)

Barbara Guidetti

2009-07-01

Full Text Available Summary of the International Conference held on 15 and May 16, 2009 in Verona. An event planned at the end of a Research Project of National Interest (PRIN designed to detect and promote the practices of education for democratic citizenship in Italian schools, following the guidelines of the Council of Europe on Education for Democratic Citizenship (EDC and using the methodologies proposed in the "Tool for Quality Assurance of EDC in schools".

Mirror Confinement Systems: project summaries

International Nuclear Information System (INIS)

1980-07-01

This report contains descriptions of the projects supported by the Mirror Confinement Systems (MCS) Division of the Office of Fusion Energy. The individual project summaries were prepared by the principal investigators, in collaboration with MCS staff office, and include objectives and milestones for each project. In addition to project summaries, statements of Division objectives and budget summaries are also provided

Metallothionein (MT)-III

DEFF Research Database (Denmark)

Carrasco, J; Giralt, M; Molinero, A

1999-01-01

Metallothionein-III is a low molecular weight, heavy-metal binding protein expressed mainly in the central nervous system. First identified as a growth inhibitory factor (GIF) of rat cortical neurons in vitro, it has subsequently been shown to be a member of the metallothionein (MT) gene family...... injected rats. The specificity of the antibody was also demonstrated in immunocytochemical studies by the elimination of the immunostaining by preincubation of the antibody with brain (but not liver) extracts, and by the results obtained in MT-III null mice. The antibody was used to characterize...... the putative differences between the rat brain MT isoforms, namely MT-I+II and MT-III, in the freeze lesion model of brain damage, and for developing an ELISA for MT-III suitable for brain samples. In the normal rat brain, MT-III was mostly present primarily in astrocytes. However, lectin staining indicated...

Minerals Yearbook, volume III, Area Reports—International

Science.gov (United States)

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Development of a methodology for defining whole-building energy design targets for commercial buildings: Phase 2, Development concept stage report

Energy Technology Data Exchange (ETDEWEB)

Jones, J.W. (American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc., Atlanta, GA (USA)); Deringer, J.J. (Deringer Group, Riva, MD (USA)); Hall, J.D. (American Inst. of Architects, Washington, DC (USA)) (comps.)

1990-09-01

The Whole-Building Energy Design Targets project is being conducted for the US Department of Energy (DOE) by the Pacific Northwest Laboratory (PNL). The objective of the project is to develop a flexible methodology for setting energy performance guidelines with which architects, engineers, planners, and owners can assess energy efficiency in commercial building design. This volume, the third in the four-volume report on the Targets project concept stage, contains the minutes of the workshops as well as summaries of the expert's written comments prepared at the close of each workshop. In Section 2, the building energy simulation workshop is summarized. Section 3 provides a summary of the building cost workshop.

Model summary report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Vahlund, Fredrik

2006-10-15

This document is the model summary report for the safety assessment SR-Can. In the report, the quality assurance measures conducted for the assessment codes are presented together with the chosen methodology. In the safety assessment SR-Can, a number of different computer codes are used. In order to better understand how these codes are related Assessment Model Flowcharts, AMFs, have been produced within the project. From these, it is possible to identify the different modelling tasks and consequently also the different computer codes used. A large number of different computer codes are used in the assessment of which some are commercial while others are developed especially for the current assessment project. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined: It must be demonstrated that the code is suitable for its purpose; It must be demonstrated that the code has been properly used; and, It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. Although the requirements are identical for all codes, the measures used to show that the requirements are fulfilled will be different for different codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented and it is shown how the requirements are met.

Model summary report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Vahlund, Fredrik

2006-10-01

This document is the model summary report for the safety assessment SR-Can. In the report, the quality assurance measures conducted for the assessment codes are presented together with the chosen methodology. In the safety assessment SR-Can, a number of different computer codes are used. In order to better understand how these codes are related Assessment Model Flowcharts, AMFs, have been produced within the project. From these, it is possible to identify the different modelling tasks and consequently also the different computer codes used. A large number of different computer codes are used in the assessment of which some are commercial while others are developed especially for the current assessment project. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined: It must be demonstrated that the code is suitable for its purpose; It must be demonstrated that the code has been properly used; and, It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. Although the requirements are identical for all codes, the measures used to show that the requirements are fulfilled will be different for different codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented and it is shown how the requirements are met

Handbook of five methodologies for the assessment of load management

Energy Technology Data Exchange (ETDEWEB)

1980-02-01

This report provides a summary description and evaluation of five methodologies that have been developed for the assessment of utility costs and benefits of load-management programs, including marginal-costing methodologies and an integrated set of utility-system planning and production costing models. Of the two basic methods, the first uses marginal-cost data to compute the cumulative reduction in utility-system costs realized in moving units of load from periods of high marginal cost to periods of low marginal cost. The present value of these cost savings may be compared directly with the costs of implementing the load-management program. The second method relies on an evaluation of future total-system costs. System planning and production-costing models are used to calculate the total fixed and variable costs of meeting baseline and alternative-load configurations. The difference between baseline system costs and the costs with load management may then be compared to the costs of implementing the program. The advantages and disadvantages of each method are summarized briefly.

Sorption behavior of europium(III) and curium(III) on the cell surfaces of microorganisms

International Nuclear Information System (INIS)

Ozaki, T.; Kimura, T.; Ohnuki, T.; Yoshida, Z.; Gillow, J.B.; Francis, A.J.

2004-01-01

We investigated the association of europium(III) and curium(III) with the microorganisms Chlorella vulgaris, Bacillus subtilis, Pseudomonas fluorescens, Halomonas sp., Halobacterium salinarum, and Halobacterium halobium. We determined the kinetics and distribution coefficients (K d ) for Eu(III) and Cm(III) sorption at pH 3-5 by batch experiments, and evaluated the number of water molecules in the inner-sphere (N H 2 O ) and the degree of strength of ligand field (R E/M ) for Eu(III) by time-resolved laser-induced fluorescence spectroscopy (TRLFS). Exudates from C. vulgaris, Halomonas sp., and H. halobium had an affinity for Eu(III) and Cm(III). The log K d of Eu(III) and Cm(III) showed that their sorption was not fully due to the exchange with three protons on the functional groups on cell surfaces. The halophilic microorganisms (Halomonas sp., Halobacterium salinarum, H. halobium) showed almost no pH dependence in log K d , indicating that an exchange with Na + on the functional groups was involved in their sorption. The ΔN H 2 O (= 9 - N H 2 O ) for Eu(III) on C. vulgaris was 1-3, while that for the other microorganisms was over 3, demonstrating that the coordination of Eu(III) with C. vulgaris was predominantly an outer-spherical process. The R E/M for Eu(III) on halophilic microorganisms was 2.5-5, while that for non-halophilic ones was 1-2.5. This finding suggests that the coordination environment of Eu(III) on the halophilic microorganisms is more complicated than that on the other three non-halophilic ones. (orig.)

Sorption behavior of europium(III) and curium(III) on the cell surfaces of microorganisms

Energy Technology Data Exchange (ETDEWEB)

Ozaki, T.; Kimura, T.; Ohnuki, T.; Yoshida, Z. [Advanced Science Research Center, Japan Atomic Energy Research Inst., Ibaraki (Japan); Gillow, J.B.; Francis, A.J. [Environmental Sciences Dept., Brookhaven National Lab., Upton, NY (United States)

2004-07-01

We investigated the association of europium(III) and curium(III) with the microorganisms Chlorella vulgaris, Bacillus subtilis, Pseudomonas fluorescens, Halomonas sp., Halobacterium salinarum, and Halobacterium halobium. We determined the kinetics and distribution coefficients (K{sub d}) for Eu(III) and Cm(III) sorption at pH 3-5 by batch experiments, and evaluated the number of water molecules in the inner-sphere (N{sub H{sub 2}O}) and the degree of strength of ligand field (R{sub E/M}) for Eu(III) by time-resolved laser-induced fluorescence spectroscopy (TRLFS). Exudates from C. vulgaris, Halomonas sp., and H. halobium had an affinity for Eu(III) and Cm(III). The log K{sub d} of Eu(III) and Cm(III) showed that their sorption was not fully due to the exchange with three protons on the functional groups on cell surfaces. The halophilic microorganisms (Halomonas sp., Halobacterium salinarum, H. halobium) showed almost no pH dependence in log K{sub d}, indicating that an exchange with Na{sup +} on the functional groups was involved in their sorption. The {delta}N{sub H{sub 2}O} (= 9 - N{sub H{sub 2}O}) for Eu(III) on C. vulgaris was 1-3, while that for the other microorganisms was over 3, demonstrating that the coordination of Eu(III) with C. vulgaris was predominantly an outer-spherical process. The R{sub E/M} for Eu(III) on halophilic microorganisms was 2.5-5, while that for non-halophilic ones was 1-2.5. This finding suggests that the coordination environment of Eu(III) on the halophilic microorganisms is more complicated than that on the other three non-halophilic ones. (orig.)

Guide to preemption of state-law claims against Class III PMA medical devices.

Science.gov (United States)

Whitney, Daniel W

2010-01-01

There is a perception that the express preemption holding of the Supreme Court in Riegel v. Medtronic, 552 U.S. 312(2008), immunizes medical device manufacturers from common law personal injury actions involving Class III devices that received FDA clearance under a premarket approval application (PMA). In the aftermath of Riegel, many lawsuits involving Class III PMA devices have been dismissed by district courts applying the new heightened pleading standard of Bell Atlantic Corp. v. Twombly, 550 U.S. 544 (2007). Other lawsuits involving Class III PMA devices premised on fraud-on-FDA have been dismissed based on the implied preemption holding of the Supreme Court in Buckman v. Plaintiffs' Legal Comm., 531 U.S. 341 (2001). When these decisions are carefully analyzed together with Medtronic, Inc. v. Lohr, 518 U.S. 470 (1996), which found no preemption regarding a Class III device receiving FDA clearance through the 510(k) mechanism, it is apparent that the preemption defense does not apply universally to Class III PMA devices. The overall methodology for framing a non-preempted claim is to first identify conduct which violated the PMA or other specific requirements related to safety or efficacy. If such conduct can also be stated in terms of a breach of a parallel common law duty (e.g, failure to warn under strict liability or negligence, manufacturing defect or breach of warranty), then it would appear the claim is not preempted. Alternatively, regardless of a specific violation, common law remedies are not preempted by general CGMP requirements.

Development and Implementation of Efficiency-Improving Analysis Methods for the SAGE III on ISS Thermal Model Originating

Science.gov (United States)

Liles, Kaitlin; Amundsen, Ruth; Davis, Warren; Scola, Salvatore; Tobin, Steven; McLeod, Shawn; Mannu, Sergio; Guglielmo, Corrado; Moeller, Timothy

2013-01-01

The Stratospheric Aerosol and Gas Experiment III (SAGE III) instrument is the fifth in a series of instruments developed for monitoring aerosols and gaseous constituents in the stratosphere and troposphere. SAGE III will be delivered to the International Space Station (ISS) via the SpaceX Dragon vehicle in 2015. A detailed thermal model of the SAGE III payload has been developed in Thermal Desktop (TD). Several novel methods have been implemented to facilitate efficient payload-level thermal analysis, including the use of a design of experiments (DOE) methodology to determine the worst-case orbits for SAGE III while on ISS, use of TD assemblies to move payloads from the Dragon trunk to the Enhanced Operational Transfer Platform (EOTP) to its final home on the Expedite the Processing of Experiments to Space Station (ExPRESS) Logistics Carrier (ELC)-4, incorporation of older models in varying unit sets, ability to change units easily (including hardcoded logic blocks), case-based logic to facilitate activating heaters and active elements for varying scenarios within a single model, incorporation of several coordinate frames to easily map to structural models with differing geometries and locations, and streamlined results processing using an Excel-based text file plotter developed in-house at LaRC. This document presents an overview of the SAGE III thermal model and describes the development and implementation of these efficiency-improving analysis methods.

77 FR 12865 - Enforcement Actions Summary

Science.gov (United States)

2012-03-02

...] Enforcement Actions Summary AGENCY: Transportation Security Administration, DHS. ACTION: Notice of availability. SUMMARY: The Transportation Security Administration (TSA) is providing notice that it has issued an annual summary of all enforcement actions taken by TSA under the authority granted in the...

78 FR 11216 - Enforcement Actions Summary

Science.gov (United States)

2013-02-15

...] Enforcement Actions Summary AGENCY: Transportation Security Administration, DHS. ACTION: Notice of availability. SUMMARY: The Transportation Security Administration (TSA) is providing notice that it has issued an annual summary of all enforcement actions taken by TSA under the authority granted in the...

76 FR 9357 - Enforcement Actions Summary

Science.gov (United States)

2011-02-17

...] Enforcement Actions Summary AGENCY: Transportation Security Administration, DHS. ACTION: Notice of Availability. SUMMARY: The Transportation Security Administration (TSA) is providing notice that it has issued an annual summary of all enforcement actions taken by TSA under the authority granted in the...

Transuranium perrhenates: Np(IV), Pu(IV) and (III), Am (III)

International Nuclear Information System (INIS)

Silvestre, Jean-Paul; Freundlich, William; Pages, Monique

1977-01-01

Synthesis in aqueous solution and by solid state reactions, crystallographical characterization and study of the stability of some transuranium perrhenates: Asup(n+)(ReO 4 - )sub(n) (A=Np(IV), Pu(IV), Pu(III), Am(III) [fr

The use of online methodologies in studying paraphilias - A review.

Science.gov (United States)

Griffiths, Mark D

2012-12-01

Aims The paper outlines the advantages, disadvantages, and other implications of using the Internet to collect data from those people displaying sexually paraphilic behavior. Method Using empirical and clinical studies published in the paraphilia literature, the main issues concerning online paraphilic data collection are reviewed and discussed. Results The specific online data collection methods examined included the collection of paraphilic data via (i) online questionnaires, (ii) online forums, (iii) online interviews, and (iv) online participant observation. Conclusions It is concluded that there are many useful and practical advantages of using online research methodologies to examine sexually paraphilic behavior.

Evaluating the statistical methodology of randomized trials on dentin hypersensitivity management.

Science.gov (United States)

Matranga, Domenica; Matera, Federico; Pizzo, Giuseppe

2017-12-27

The present study aimed to evaluate the characteristics and quality of statistical methodology used in clinical studies on dentin hypersensitivity management. An electronic search was performed for data published from 2009 to 2014 by using PubMed, Ovid/MEDLINE, and Cochrane Library databases. The primary search terms were used in combination. Eligibility criteria included randomized clinical trials that evaluated the efficacy of desensitizing agents in terms of reducing dentin hypersensitivity. A total of 40 studies were considered eligible for assessment of quality statistical methodology. The four main concerns identified were i) use of nonparametric tests in the presence of large samples, coupled with lack of information about normality and equality of variances of the response; ii) lack of P-value adjustment for multiple comparisons; iii) failure to account for interactions between treatment and follow-up time; and iv) no information about the number of teeth examined per patient and the consequent lack of cluster-specific approach in data analysis. Owing to these concerns, statistical methodology was judged as inappropriate in 77.1% of the 35 studies that used parametric methods. Additional studies with appropriate statistical analysis are required to obtain appropriate assessment of the efficacy of desensitizing agents.

Capacitación profesoral en la asignatura Morfofisiología III, carrera de Estomatología. Curso 2008-2009 Teaching training in Morpho-physiology-III discipline. Dentistry major, 2008-2009

Directory of Open Access Journals (Sweden)

Juan Félix Albert Díaz

2010-06-01

Full Text Available Los profesores que imparten la disciplina curricular Morfofisiología, muestran debilidades en su proceso formativo, con vistas a garantizar la calidad que el proceso de enseñanza aprendizaje requiere. Objetivo: caracterizar a los profesores que imparten la asignatura Morfofisiología III en las SUM, teniendo en cuenta su preparación metodológica y conocimientos pedagógicos, que permita el diseño de una estrategia para su capacitación. Método: se realizó una investigación descriptiva y de corte transversal, con vistas a caracterizar el claustro profesoral que imparte la asignatura Morfofisiología III, de la carrera de Estomatología de la provincia de Pinar del Río, en las nueve SUM en las que la asignatura se encuentra universalizada, previo al comienzo del segundo semestre del curso 2008-2009. La muestra estuvo constituida por 12 de dichos profesores. Los datos fueron procesados utilizando la estadística descriptiva y la prueba Ji cuadrado. Resultados: estos mostraron que los profesores de la asignatura Morfofisiología III, en las SUM, carecen de la preparación metodológica y de los conocimientos en los contenidos propios de la asignatura, necesarios para enfrentar el proceso, elementos que se tuvieron en cuenta en el diseño del diplomado, el cual se estructuró siguiendo los principios de la educación a distancia. Se concluye a partir del diagnóstico realizado, sobre la necesidad de la instrumentación del diplomado diseñado.The teaching staff of Morpho-physiology discipline shows weak points in the formative process, to guarantee the quality of the teaching-learning process it is required; Objective: To characterize the teaching staff of Morpho-physiology -III in the University Venues, taking into account the methodological preparation and pedagogical knowledge, to allow the design of a strategy to their training. Method: A descriptive and cross-sectional research was conducted to characterize the teaching staff of Morpho

Diffusion of Na(I), Cs(I), Sr(II) and Eu(III) in smectite rich natural clay.

Science.gov (United States)

Kasar, Sharayu; Kumar, Sumit; Bajpai, R K; Tomar, B S

2016-01-01

Diffusion of Na(I), Cs(I), Sr(II) and Eu(III) in smectite rich natural clay, proposed as a backfill material in the Indian geological repository, was studied using the out-diffusion method. Radiotracers (22)Na, (137)Cs, (85)Sr and (154)Eu were used; the first three are carrier-free enabling experimental work at sub-micromolar metal ion concentration, and Eu(III) tracer (154)Eu was used at sub millimolar concentration. An out-diffusion methodology, wherein a thin planar source of radioactivity placed between two clay columns diffuses out, was used to obtain the apparent diffusion coefficient (Da) values. This methodology enabled determination of diffusion coefficient even for strongly sorbing (154)Eu. Da values for (22)Na, (137)Cs, (85)Sr and (154)Eu were 2.35 (±0.14) × 10(-11), 2.65 (±0.09) × 10(-12), 3.32 (±0.15) × 10(-11) and 1.23 (±0.15) × 10(-13) m(2) s(-1), respectively. Da values were found to be in fair agreement with literature data reported for similar mineralogical sediments. Sorption of radionuclides on the clay was also determined in the present study and differences in Da values were rationalized on the basis of sorption data. Distribution ratios (Kd) for Cs(I) and Eu(III) were higher than that for Sr(II), which in turn was higher than that for Na(I). Copyright © 2015 Elsevier Ltd. All rights reserved.

Pyridine synthesis by reactions of allyl amines and alkynes proceeding through a Cu(OAc)2 oxidation and Rh(III)-catalyzed N-annulation sequence.

Science.gov (United States)

Kim, Dong-Su; Park, Jung-Woo; Jun, Chul-Ho

2012-11-28

A new methodology has been developed for the synthesis of pyridines from allyl amines and alkynes, which involves sequential Cu(II)-promoted dehydrogenation of the allylamine and Rh(III)-catalyzed N-annulation of the resulting α,β-unsaturated imine and alkyne.

19 CFR 210.18 - Summary determinations.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 3 2010-04-01 2010-04-01 false Summary determinations. 210.18 Section 210.18 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Motions § 210.18 Summary determinations. (a) Motions for summary...

Development of flaw assesment methodology for elevated temperature components of FBR plants

International Nuclear Information System (INIS)

Shimakawa, Takashi; Takahashi, Yukio; Miura, Naoki; Nakayama, Yasunari; Sawai, Tatsuaki; Tooya, Yuuji

1999-01-01

Fracture mechanics is applicable for the safety assessment of FBR component if a crack is assumed to exist. Inelastic response should be taken into account due to high temperature operation of FBR components. However, methodology for the application of inelastic fracture mechanics has not been established sufficiently. CRIEPI has been conducted research projects to develop a flaw assessment guideline for FBR components. This guideline consists of evaluation methods for creep-fatigue crack propagation, ductile fracture and sodium leak rate. The summary of evaluation methods on creep-fatigue crack and ductile fracture is presented in this paper. (author)

Synthesis and characterisation of the Fe(II-III) hydroxy-formate green rust

International Nuclear Information System (INIS)

Refait, P.; Abdelmoula, M.; Genin, J.-M. R.; Jeannin, M.

2006-01-01

A new methodology was envisioned in order to prepare green rust compounds build on organic anions that could intervene in microbiologically influenced corrosion processes of iron and steel. The formate ion was chosen as an example. The formation of rust was simulated by the oxidation of aqueous suspensions of Fe(OH) 2 precipitated from Fe(II) lactate and sodium hydroxide, in the presence of sodium formate to promote the formation of the corresponding green rust. The evolution of the precipitate with time was followed by transmission Moessbauer spectroscopy at 15 K. It was observed that the initial hydroxide was transformed into a new GR compound. Its spectrum is composed of three quadrupole doublets, D 1 (δ = 1.28 mm s -1 , Δ = 2.75 mm s -1 ) and D 2 (δ = 1.28 mm s -1 , Δ 2.48 mm s -1 ) that correspond to Fe(II) and D 3 (δ = 0.49 mm s -1 , Δ = 0.37 mm s -1 ) that corresponds to Fe(III). The relative area of D 3 , close to the proportion of Fe(III) in the GR, was found at 28.5 ± 1.5% (∼2/7). Raman spectroscopy confirmed that the intermediate compound was a Fe(II-III) hydroxy-formate, GR(HCOO - ).

Summary for Policy Makers: Intergovernmental Panel on Climate Change Special Report Renewable Energy Sources (SRREN)

Energy Technology Data Exchange (ETDEWEB)

Arvizu, Dan; Bruckner, Thomas; Christensen, John; Devernay, Jean-Michel; Faaij , Andre; Fischedick, Manfred; Goldstein, Barry; Hansen, Gerrit; Huckerby , John; Jager-Waldau, Arnulf; Kadner, Susanne; Kammen, Daniel; Krey, Volker; Kumar, Arun; Lewis , Anthony; Lucon, Oswaldo; Matschoss, Patrick; Maurice, Lourdes; Mitchell , Catherine; Moomaw, William; Moreira, Jose; Nadai, Alain; Nilsson, Lars J.; Nyboer, John; Rahman, Atiq; Sathaye, Jayant; Sawin, Janet; Schaeffer, Roberto; Schei, Tormod; Schlomer, Steffen; Sims, Ralph; von Stechow, Christoph; Verbruggen, Aviel; Urama, Kevin; Wiser, Ryan; Yamba, Francis; Zwickel, Timm

2011-05-08

The Working Group III Special Report on Renewable Energy Sources and Climate Change Mitigation (SRREN) presents an assessment of the literature on the scientific, technological, environmental, economic and social aspects of the contribution of six renewable energy (RE) sources to the mitigation of climate change. It is intended to provide policy relevant information to governments, intergovernmental processes and other interested parties. This Summary for Policymakers provides an overview of the SRREN, summarizing the essential findings. The SRREN consists of 11 chapters. Chapter 1 sets the context for RE and climate change; Chapters 2 through 7 provide information on six RE technologies, and Chapters 8 through 11 address integrative issues.

Summary of blog

CERN Document Server

Reader, Capitol

2013-01-01

This ebook consists of a summary of the ideas, viewpoints and facts presented by Hugh Hewitt in his book "Blog: Understanding the Information Reformation that's Changing Your World". This summary offers a concise overview of the entire book in less than 30 minutes reading time. However this work does not replace in any case Hugh Hewitt's book.Hewitt argues that blogs have an important potential and he believes that it would be a dreadful mistake to avoid their power.

Family History as Media and Methodological Inspiration for History Teaching

Directory of Open Access Journals (Sweden)

KAMIL ŠTĚPÁNEK

2017-10-01

Full Text Available The text of the contribution is inspired by relationships and issues arising from communication among parents, children, grandparents and grandchildren. It ensues from such terms as generation crisis, cohesion, cultivation of common values or family topics. It deals with family history captured in a family amateur movie, which is an appropriate media of alternative school and out-of-school pupils' activities.Within its framework the pupils can become aware of their own roots and evolution of their family histories, or how their histories were influenced by „the great history”. The presentation methodology of the summary of these pupils' explorations of private family materials used in history lessons forms an inseparable part.

McKenzie River Subbasin Assessment, Technical Report 2000.

Energy Technology Data Exchange (ETDEWEB)

Alsea Geospatial, Inc.

2000-02-01

This document details the findings of the McKenzie River Subbasin Assessment team. The goal of the subbasin assessment is to provide an ecological assessment of the McKenzie River Floodplain, identification of conservation and restoration opportunities, and discussion of the influence of some upstream actions and processes. This Technical Report can be viewed in conjunction with the McKenzie River Subbasin Summary or as a stand-alone document. The purpose of the technical report is to detail the methodology and findings of the consulting team that the observations and recommendations in the summary document are based on. This part, Part I, provides an introduction to the subbasin and a general overview. Part II details the specific findings of the science team. Part III provides an explanation and examples of how to use the data that has been developed through this assessment to aid in prioritizing restoration activities. Part III also includes the literature cited and appendices.

29 CFR 1905.41 - Summary decision.

Science.gov (United States)

2010-07-01

... OCCUPATIONAL SAFETY AND HEALTH ACT OF 1970 Summary Decisions § 1905.41 Summary decision. (a) No genuine issue... 29 Labor 5 2010-07-01 2010-07-01 false Summary decision. 1905.41 Section 1905.41 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR RULES OF...

40 CFR 68.155 - Executive summary.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Executive summary. 68.155 Section 68...) CHEMICAL ACCIDENT PREVENTION PROVISIONS Risk Management Plan § 68.155 Executive summary. The owner or operator shall provide in the RMP an executive summary that includes a brief description of the following...

Computerized summary scoring: crowdsourcing-based latent semantic analysis.

Science.gov (United States)

Li, Haiying; Cai, Zhiqiang; Graesser, Arthur C

2017-11-03

In this study we developed and evaluated a crowdsourcing-based latent semantic analysis (LSA) approach to computerized summary scoring (CSS). LSA is a frequently used mathematical component in CSS, where LSA similarity represents the extent to which the to-be-graded target summary is similar to a model summary or a set of exemplar summaries. Researchers have proposed different formulations of the model summary in previous studies, such as pregraded summaries, expert-generated summaries, or source texts. The former two methods, however, require substantial human time, effort, and costs in order to either grade or generate summaries. Using source texts does not require human effort, but it also does not predict human summary scores well. With human summary scores as the gold standard, in this study we evaluated the crowdsourcing LSA method by comparing it with seven other LSA methods that used sets of summaries from different sources (either experts or crowdsourced) of differing quality, along with source texts. Results showed that crowdsourcing LSA predicted human summary scores as well as expert-good and crowdsourcing-good summaries, and better than the other methods. A series of analyses with different numbers of crowdsourcing summaries demonstrated that the number (from 10 to 100) did not significantly affect performance. These findings imply that crowdsourcing LSA is a promising approach to CSS, because it saves human effort in generating the model summary while still yielding comparable performance. This approach to small-scale CSS provides a practical solution for instructors in courses, and also advances research on automated assessments in which student responses are expected to semantically converge on subject matter content.

Conference summaries

International Nuclear Information System (INIS)

1987-01-01

This volume contains summaries of 28 papers presented at the 27. conference of the Canadian Nuclear Association. These papers discuss the general situation of the Canadian nuclear industry and the CANDU reactor; dialogue with the public; the International Atomic Energy Agency; and economic goals and operating lessons. It also contains summaries of 70 papers presented at the 8. conference of the Canadian Nuclear Society, which discuss plant life extension; safety and the environment; reactor physics; thermalhydraulics; risk assessment; the CANDU spacer location and repositioning project; CANDU operations; safety research after Chernobyl; fuel channels; and nuclear technology developments. The individual papers are also available in INIS-mf--13673 (CNA), and INIS-mf--12909 (CNS). (L.L.)

Repository environmental parameters and models/methodologies relevant to assessing the performance of high-level waste packages in basalt, tuff, and salt

Energy Technology Data Exchange (ETDEWEB)

Claiborne, H.C.; Croff, A.G.; Griess, J.C.; Smith, F.J.

1987-09-01

This document provides specifications for models/methodologies that could be employed in determining postclosure repository environmental parameters relevant to the performance of high-level waste packages for the Basalt Waste Isolation Project (BWIP) at Richland, Washington, the tuff at Yucca Mountain by the Nevada Test Site, and the bedded salt in Deaf Smith County, Texas. Guidance is provided on the identify of the relevant repository environmental parameters; the models/methodologies employed to determine the parameters, and the input data base for the models/methodologies. Supporting studies included are an analysis of potential waste package failure modes leading to identification of the relevant repository environmental parameters, an evaluation of the credible range of the repository environmental parameters, and a summary of the review of existing models/methodologies currently employed in determining repository environmental parameters relevant to waste package performance. 327 refs., 26 figs., 19 tabs.

Repository environmental parameters and models/methodologies relevant to assessing the performance of high-level waste packages in basalt, tuff, and salt

International Nuclear Information System (INIS)

Claiborne, H.C.; Croff, A.G.; Griess, J.C.; Smith, F.J.

1987-09-01

This document provides specifications for models/methodologies that could be employed in determining postclosure repository environmental parameters relevant to the performance of high-level waste packages for the Basalt Waste Isolation Project (BWIP) at Richland, Washington, the tuff at Yucca Mountain by the Nevada Test Site, and the bedded salt in Deaf Smith County, Texas. Guidance is provided on the identify of the relevant repository environmental parameters; the models/methodologies employed to determine the parameters, and the input data base for the models/methodologies. Supporting studies included are an analysis of potential waste package failure modes leading to identification of the relevant repository environmental parameters, an evaluation of the credible range of the repository environmental parameters, and a summary of the review of existing models/methodologies currently employed in determining repository environmental parameters relevant to waste package performance. 327 refs., 26 figs., 19 tabs

U.S. Annual Climatological Summaries

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Annual Climatological Summary contains historical monthly and annual summaries for over 8000 U.S. locations. Observing stations are located in the United States of...

Basel III D: Swiss Finish to Basel III

OpenAIRE

Christian M. McNamara; Natalia Tente; Andrew Metrick

2014-01-01

After the Basel Committee on Banking Supervision (BCBS) introduced the Basel III framework in 2010, individual countries confronted the question of how best to implement the framework given their unique circumstances. Switzerland, with a banking industry that is both heavily concentrated and very large relative to the size of its overall economy, faced a special challenge. It ultimately adopted what is sometimes referred to as the “Swiss Finish” to Basel III – enhanced requirements applicable...

SKI SITE-94. Deep Repository Performance Assessment Project. Summary

International Nuclear Information System (INIS)

1997-02-01

The function of SITE-94 is to provide the Swedish Nuclear Power Inspectorate (SKI) with the capacity and supporting knowledge needed for reviewing the Swedish nuclear industry's R and D programs and for reviewing license applications, as stipulated in Swedish legislation. The report is structured as a Performance Assessment exercise needed for input to decisions regarding repository safety, but the SITE-94 is neither a safety assessment nor a model for future assessments to be undertaken by the prospective licensee. The specific project objectives of SITE-94 comprise site evaluation, performance assessment methodology, canister integrity and radionuclide release and transport calculations. The main report (SKI-R--96-36) gives a detailed description of the many inter-related studies undertaken as part of the research project, while the present report presents a condensed summary of the main report. 46 refs

Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

International Nuclear Information System (INIS)

Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E.

2014-01-01

Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH) 3 ·3H 2 O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH) 3 (am) was stable with a solubility lower than 50 μg/l in the range 5.7 0.75 Cr 0.25 (OH) 3 , the stability region was extended to 4.8 3 ·xH 2 O whereas in the presence of iron the precipitate is a mixed Fe (1−x) Cr x (OH) 3 phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe x ,Cr 1−x )(OH) 3 hydroxides as compared to the stability of Cr(OH) 3 . We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH) 3 ·3H 2 O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH) 3 (am) phase. Mixed Fe 0.75 Cr 0.25 (OH) 3 hydroxides were found to be of the ferrihydrite structure, Fe(OH) 3 , and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe(III)–Cr(III) hydroxides are more effective enhancers of groundwater quality, in comparison to the plain amorphous or crystalline Cr(III) hydroxides, the latter found to have a solubility typically higher than 50 μg/l (maximum EU permitted Cr level in drinking water), while the amorphous Cr(OH) 3 (am) phase was within the drinking water threshold in the range 5.7 0.75 Cr 0.25 (OH) 3 hydroxides studied were of extended stability in the 4.8 < pH < 13.5 range

Nagra technical report 14-02, geological basics - Dossier I - Introduction and summary

International Nuclear Information System (INIS)

Gautschi, A.; Zuidema, P.

2014-01-01

This dossier is the first of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. It presents an introduction to and a summary of the further seven dossiers on basic geological conditions. Dossier II considers the sediments that can be used along with tectonic considerations, Dossier III takes a look at long-term geological developments and Dossier IV considers the geo-mechanical documentation available. Dossier V looks at hydro-geological considerations. Dossier VI reports on the barrier properties of the proposed host rock sediments and neighbouring rock layers. Dossiers VII takes a look at usage conflicts and Dossier VIII considers the possibilities for the characterisation of the substrates and for the ways in which they can be explored

Methodology in conducting a systematic review of systematic reviews of healthcare interventions

LENUS (Irish Health Repository)

Smith, Valerie

2011-02-03

Abstract Background Hundreds of studies of maternity care interventions have been published, too many for most people involved in providing maternity care to identify and consider when making decisions. It became apparent that systematic reviews of individual studies were required to appraise, summarise and bring together existing studies in a single place. However, decision makers are increasingly faced by a plethora of such reviews and these are likely to be of variable quality and scope, with more than one review of important topics. Systematic reviews (or overviews) of reviews are a logical and appropriate next step, allowing the findings of separate reviews to be compared and contrasted, providing clinical decision makers with the evidence they need. Methods The methods used to identify and appraise published and unpublished reviews systematically, drawing on our experiences and good practice in the conduct and reporting of systematic reviews are described. The process of identifying and appraising all published reviews allows researchers to describe the quality of this evidence base, summarise and compare the review\\'s conclusions and discuss the strength of these conclusions. Results Methodological challenges and possible solutions are described within the context of (i) sources, (ii) study selection, (iii) quality assessment (i.e. the extent of searching undertaken for the reviews, description of study selection and inclusion criteria, comparability of included studies, assessment of publication bias and assessment of heterogeneity), (iv) presentation of results, and (v) implications for practice and research. Conclusion Conducting a systematic review of reviews highlights the usefulness of bringing together a summary of reviews in one place, where there is more than one review on an important topic. The methods described here should help clinicians to review and appraise published reviews systematically, and aid evidence-based clinical decision-making.

Binary and ternary chelates of Sc(III), Y(III) and La(III) with ethylenediamine tetraacetic acid as primary ligand and substituted salicylic acids as secondary ligands

Energy Technology Data Exchange (ETDEWEB)

Pandey, A K; Chandra, M; Agarwala, B V; Dey, A K [Allahabad Univ. (India). Chemical Labs.

1980-02-01

Study of ternary complex formation of several tripositive metal ions viz. Sc(III), Y(III) and La(III) with ethylenediamine tetraacetic acid (EDTA) as a primary ligand and 5-chlorosalicylic acid (CSA) or 3,5-dibromosalicylic acid (DBSA) as secondary ligands by pH-metric titration technique is reported. The stability order of metal chelates with respect to ligands is observed to be DBSA>CSA and with respect to metal ions Sc(III)>Y(III)>La(III).

Semiconducting III-V compounds

CERN Document Server

Hilsum, C; Henisch, Heinz R

1961-01-01

Semiconducting III-V Compounds deals with the properties of III-V compounds as a family of semiconducting crystals and relates these compounds to the monatomic semiconductors silicon and germanium. Emphasis is placed on physical processes that are peculiar to III-V compounds, particularly those that combine boron, aluminum, gallium, and indium with phosphorus, arsenic, and antimony (for example, indium antimonide, indium arsenide, gallium antimonide, and gallium arsenide).Comprised of eight chapters, this book begins with an assessment of the crystal structure and binding of III-V compounds, f

29 CFR 1904.32 - Annual summary.

Science.gov (United States)

2010-07-01

... 29 Labor 5 2010-07-01 2010-07-01 false Annual summary. 1904.32 Section 1904.32 Labor Regulations... Requirements § 1904.32 Annual summary. (a) Basic requirement. At the end of each calendar year, you must: (1... deficiencies identified; (2) Create an annual summary of injuries and illnesses recorded on the OSHA 300 Log...

Research on Evaluation Methodology for High Temperature Components and Technical Issues

International Nuclear Information System (INIS)

Kim, Y.J.; Han, S.B.

2007-03-01

The research on evaluation methodology for high temperature components and technical issues includes the comparison of evaluation technology of Very High Temperature Reactors(VHTRs) with that of present commercial reactors, the review of Hot Gas Duct(HGD) insulation designs, the analysis of the codes related to VHTR component construction and the analysis of technical issues on application of present codes to HGD construction. Codes to assure the integrity of the VHTR components are not fully prepared yet in any country. To understand the evaluation technology of the VHTR-related codes, key requirements of ASME B and PV Code Section III, Subsection NB and NH were compared. Six kinds of HGD designs were reviewed and compared. A reference which analyzed seven kinds of present component codes were reviewed and the limitations of them were summarized. Especially it was found that the selection of materials is limited, material property data are not enough, and design analysis methodology is not fully specified

Non-linear mixed effects modeling - from methodology and software development to driving implementation in drug development science.

Science.gov (United States)

Pillai, Goonaseelan Colin; Mentré, France; Steimer, Jean-Louis

2005-04-01

Few scientific contributions have made significant impact unless there was a champion who had the vision to see the potential for its use in seemingly disparate areas-and who then drove active implementation. In this paper, we present a historical summary of the development of non-linear mixed effects (NLME) modeling up to the more recent extensions of this statistical methodology. The paper places strong emphasis on the pivotal role played by Lewis B. Sheiner (1940-2004), who used this statistical methodology to elucidate solutions to real problems identified in clinical practice and in medical research and on how he drove implementation of the proposed solutions. A succinct overview of the evolution of the NLME modeling methodology is presented as well as ideas on how its expansion helped to provide guidance for a more scientific view of (model-based) drug development that reduces empiricism in favor of critical quantitative thinking and decision making.

Development of a C3-symmetric benzohydroxamate tripod: Trimetallic complexation with Fe(III), Cr(III) and Al(III)

Science.gov (United States)

Baral, Minati; Gupta, Amit; Kanungo, B. K.

2016-06-01

The design, synthesis and physicochemical characterization of a C3-symmetry Benzene-1,3,5-tricarbonylhydroxamate tripod, noted here as BTHA, are described. The chelator was built from a benzene as an anchor, symmetrically extended by three hydroxamate as ligating moieties, each bearing O, O donor sites. A combination of absorption spectrophotometry, potentiometry and theoretical investigations are used to explore the complexation behavior of the ligand with some trivalent metal ions: Fe(III), Cr(III), and Al(III). Three protonation constants were calculated for the ligand in a pH range of 2-11 in a highly aqueous medium (9:1 H2O: DMSO). A high rigidity in the molecular structure restricts the formation of 1:1 (M/L) metal encapsulation but shows a high binding efficiency for a 3:1 metal ligand stoichiometry giving formation constant (in β unit) 28.73, 26.13 and 19.69 for [M3L]; Mdbnd Fe(III), Al(III) and Cr(III) respectively, and may be considered as an efficient Fe-carrier. The spectrophotometric study reveals of interesting electronic transitions occurred during the complexation. BTHA exhibits a peak at 238 nm in acidic pH and with the increase of pH, a new peak appeared at 270 nm. A substantial shifting in both of the peaks in presence of the metal ions implicates a s coordination between ligand and metal ions. Moreover, complexation of BTHA with iron shows three distinct colors, violet, reddish orange and yellow in different pH, enables the ligand to be considered for the use as colorimetric sensor.

Hazard interactions and interaction networks (cascades) within multi-hazard methodologies

Science.gov (United States)

Gill, Joel C.; Malamud, Bruce D.

2016-08-01

This paper combines research and commentary to reinforce the importance of integrating hazard interactions and interaction networks (cascades) into multi-hazard methodologies. We present a synthesis of the differences between multi-layer single-hazard approaches and multi-hazard approaches that integrate such interactions. This synthesis suggests that ignoring interactions between important environmental and anthropogenic processes could distort management priorities, increase vulnerability to other spatially relevant hazards or underestimate disaster risk. In this paper we proceed to present an enhanced multi-hazard framework through the following steps: (i) description and definition of three groups (natural hazards, anthropogenic processes and technological hazards/disasters) as relevant components of a multi-hazard environment, (ii) outlining of three types of interaction relationship (triggering, increased probability, and catalysis/impedance), and (iii) assessment of the importance of networks of interactions (cascades) through case study examples (based on the literature, field observations and semi-structured interviews). We further propose two visualisation frameworks to represent these networks of interactions: hazard interaction matrices and hazard/process flow diagrams. Our approach reinforces the importance of integrating interactions between different aspects of the Earth system, together with human activity, into enhanced multi-hazard methodologies. Multi-hazard approaches support the holistic assessment of hazard potential and consequently disaster risk. We conclude by describing three ways by which understanding networks of interactions contributes to the theoretical and practical understanding of hazards, disaster risk reduction and Earth system management. Understanding interactions and interaction networks helps us to better (i) model the observed reality of disaster events, (ii) constrain potential changes in physical and social vulnerability

A comparative study of ion exchange properties of antimony (III) tungstoselenite with those of antimony (III) tungstate and antimony (III) selenite

International Nuclear Information System (INIS)

Janardanan, C.; Nair, S.M.K.

1996-01-01

A new inorganic ion exchanger, antimony (III) tungstoselenite, has been prepared and characterised. Its exchange capacity and distribution coefficients for various metal ions and the effects of temperature and electrolyte concentrations on ion exchange capacity have been compared with antimony (III) tungstate and antimony (III) selenite. Six binary separations using the exchanger have been carried out. (author). 7 refs., 1 tab

Fluorimetric determination of samarium(III) and europium(III) in neodymium oxide by separation with a resin column

Energy Technology Data Exchange (ETDEWEB)

Shaorong Liu; Jian Meng (Beijing Research Institute of Chemical Engineering and Metallurgy (China)); Wenhua Liu (General Research Institute for Non-Ferrous Metals (China))

1992-08-24

When thenoyltrifluoroacetone-phenanthroline-Triton X-100 is used to determine samarium(III) and europium(III) fluorimetrically, only a limited amount of neodymium(III) can be tolerated. By using an on- line separation which can partially separate neodymium(III) from samarium(III), a practical and convenient method was developed to detect samarium(III) at concentrations >0.05% and europium(III) at concentrations >0.005% in neodymium oxide. (author). 7 refs.; 4 figs.; 3 tabs.

Fluorimetric determination of samarium(III) and europium(III) in neodymium oxide by separation with a resin column

International Nuclear Information System (INIS)

Shaorong Liu; Jian Meng; Wenhua Liu

1992-01-01

When thenoyltrifluoroacetone-phenanthroline-Triton X-100 is used to determine samarium(III) and europium(III) fluorimetrically, only a limited amount of neodymium(III) can be tolerated. By using an on- line separation which can partially separate neodymium(III) from samarium(III), a practical and convenient method was developed to detect samarium(III) at concentrations >0.05% and europium(III) at concentrations >0.005% in neodymium oxide. (author). 7 refs.; 4 figs.; 3 tabs

Performance evaluation of the technical capabilities of DOE sites for disposal of mixed low-level waste. Volume 1: Executive summary

International Nuclear Information System (INIS)

1996-03-01

A team of analysts designed and conducted a performance evaluation (PE) to estimate the technical capabilities of fifteen Department of Energy sites for disposal of mixed low-level waste (i.e., waste that contains both low-level radioactive materials and hazardous constituents). Volume 1 summarizes the process for selecting the fifteen sites, the methodology used in the evaluation, and the conclusions derived from the evaluation. Volume 1 is an executive summary both of the PE methodology and of the results obtained from the PEs. While this volume briefly reviews the scope and method of analyses, its main objective is to emphasize the important insights and conclusions derived from the conduct of the PEs. Volume 2 provides details about the site-selection process, the performance-evaluation methodology, and the overall results of the analysis. Volume 3 contains detailed evaluations of the fifteen sites and discussions of the results for each site

Statistical summary 1990-91

International Nuclear Information System (INIS)

1991-01-01

The information contained in this statistical summary leaflet summarizes in bar charts or pie charts Nuclear Electric's performance in 1990-91 in the areas of finance, plant and plant operations, safety, commercial operations and manpower. It is intended that the information will provide a basis for comparison in future years. The leaflet also includes a summary of Nuclear Electric's environmental policy statement. (UK)

Indexing for summary queries

DEFF Research Database (Denmark)

Yi, Ke; Wang, Lu; Wei, Zhewei

2014-01-01

), of a particular attribute of these records. Aggregation queries are especially useful in business intelligence and data analysis applications where users are interested not in the actual records, but some statistics of them. They can also be executed much more efficiently than reporting queries, by embedding...... returned by reporting queries. In this article, we design indexing techniques that allow for extracting a statistical summary of all the records in the query. The summaries we support include frequent items, quantiles, and various sketches, all of which are of central importance in massive data analysis....... Our indexes require linear space and extract a summary with the optimal or near-optimal query cost. We illustrate the efficiency and usefulness of our designs through extensive experiments and a system demonstration....

Summary of Meson'98 Workshop

International Nuclear Information System (INIS)

Henley, E.M.

1998-01-01

One never quite knows what to say in a summary. If you were at the sessions, you heard the same talks I did. Perhaps the purpose is to summarize the parallel sessions, but like you, I can only attend one of these sessions. In addition, the time is short, so that this cannot be a real summary. What I will present are impressions of the past two days, and these will certainly be colored by my own views. Thus at the outset, let me apologize for any and all omissions and distortions. I will cover primarily the plenary session talks, but will organize this summary along the following lines: 1. vector (V) mesons; 2. pseudoscalar mesons, and 3. other subjects, notably with electrons. This afternoon's talks are so close in time to this summary that I shall omit them. (author)

Interaction of Eu(III) and Cm(III) with mucin. A key component of the human mucosa

International Nuclear Information System (INIS)

Wilke, Claudia; Barkleit, Astrid

2017-01-01

To evaluate the potential health risks caused by the ingestion of lanthanides (Ln) and actinides (An), investigations into the chemical behavior of these metals in the human gastrointestinal tract are necessary. Mucin is an important part of the protective mucosa layer in the digestive system. We have recently reported that mucin interacts strongly with Eu(III) and Cm(III), representatives of Ln(III) and An(III), respectively, under in vivo conditions. In order to investigate the complexation behavior of this protein with Ln(III)/An(III), TRLFS measurements were performed on Eu(III)/Cm(III)-mucin solutions with different protein concentrations and at different pH. The results indicate the formation of at least two independent mucin species. At higher pH, the formation of hydroxide species was also observed.

Interaction of Eu(III) and Cm(III) with mucin. A key component of the human mucosa

Energy Technology Data Exchange (ETDEWEB)

Wilke, Claudia; Barkleit, Astrid [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Chemistry of the F-Elements

2017-06-01

To evaluate the potential health risks caused by the ingestion of lanthanides (Ln) and actinides (An), investigations into the chemical behavior of these metals in the human gastrointestinal tract are necessary. Mucin is an important part of the protective mucosa layer in the digestive system. We have recently reported that mucin interacts strongly with Eu(III) and Cm(III), representatives of Ln(III) and An(III), respectively, under in vivo conditions. In order to investigate the complexation behavior of this protein with Ln(III)/An(III), TRLFS measurements were performed on Eu(III)/Cm(III)-mucin solutions with different protein concentrations and at different pH. The results indicate the formation of at least two independent mucin species. At higher pH, the formation of hydroxide species was also observed.

Separation of valence forms of chromium(III) and chromium(VI) by coprecipitation with iron(III) hydroxide

International Nuclear Information System (INIS)

Nazirmadov, B.; Khamidov, B.O.; Egorova, L.A.

1989-01-01

The sorption of 9.62·10 -5 M of Cr (III) and Cr (VI) with iron hydroxide in 1 M potassium nitrate and potassium chloride was investigated in relation to the pH of the medium. Experimental data on the sorption of chromium(III) and chromium(VI) with iron(III) hydroxide made it possible to determine the region of practically complete concentration of Cr (III) and Cr (VI) (pH = 3-6.5). The results from spectrophotometric investigations, calculated data on the distribution of the hydroxocationic forms of chromium(III) and the anions of chromium(IV), and their sorption by iron-(III) hydroxide made it possible to characterize the sorbability of the cationic and anionic forms of chromium in various degrees of oxidation. On this basis a method was developed for the separation of chromium(III) and chromium(VI) by coprecipitation on iron(III) hydroxide and their separation from the iron(III) hydroxide support

The PISC III programme: 1989 status report

International Nuclear Information System (INIS)

Crutzen, S.; Jehenson, P.; McDonald, N.

1990-01-01

The PISC Programme has the general objective of assessing procedures and techniques in use for the inspection of pressure components (in particular the vessel and piping). The Series of projects for the Inspection of Steel Components carried out since 1974 under the auspices of the CEC/JRC and the OECD/NEA is a major international effort to better assess the capability and reliability of Non Destructive Inspection procedures on structural components. The programme is now in its third phase (PISC III project); the activities are concentrated on the validation of the PISC II results (e.g. modification of the ASME Inspection Codes) on real structures containing real service defects and the extension of the PISC methodology on most important structural components made of different materials. Most of the PISC test assemblies and structure pieces are representative of (or are coming from) nuclear reactor components. (author)

Syntheses, structures, and magnetic properties of a family of heterometallic heptanuclear [Cu5Ln2] (Ln = Y(III), Lu(III), Dy(III), Ho(III), Er(III), and Yb(III)) complexes: observation of SMM behavior for the Dy(III) and Ho(III) analogues.

Science.gov (United States)

Chandrasekhar, Vadapalli; Dey, Atanu; Das, Sourav; Rouzières, Mathieu; Clérac, Rodolphe

2013-03-04

Sequential reaction of the multisite coordination ligand (LH3) with Cu(OAc)2·H2O, followed by the addition of a rare-earth(III) nitrate salt in the presence of triethylamine, afforded a series of heterometallic heptanuclear complexes containing a [Cu5Ln2] core {Ln = Y(1), Lu(2), Dy(3), Ho(4), Er(5), and Yb(6)}. Single-crystal X-ray crystallography reveals that all the complexes are dicationic species that crystallize with two nitrate anions to compensate the charge. The heptanuclear aggregates in 1-6 are centrosymmetrical complexes, with a hexagonal-like arrangement of six peripheral metal ions (two rare-earth and four copper) around a central Cu(II) situated on a crystallographic inversion center. An all-oxygen environment is found to be present around the rare-earth metal ions, which adopt a distorted square-antiprismatic geometry. Three different Cu(II) sites are present in the heptanuclear complexes: two possess a distorted octahedral coordination sphere while the remaining one displays a distorted square-pyramidal geometry. Detailed static and dynamic magnetic properties of all the complexes have been studied and revealed the single-molecule magnet behavior of the Dy(III) and Ho(III) derivatives.

Towards the methodological optimization of the moss bag technique in terms of contaminants concentrations and replicability values

Science.gov (United States)

Ares, A.; Fernández, J. A.; Carballeira, A.; Aboal, J. R.

2014-09-01

The moss bag technique is a simple and economical environmental monitoring tool used to monitor air quality. However, routine use of the method is not possible because the protocols involved have not yet been standardized. Some of the most variable methodological aspects include (i) selection of moss species, (ii) ratio of moss weight to surface area of the bag, (iii) duration of exposure, and (iv) height of exposure. In the present study, the best option for each of these aspects was selected on the basis of the mean concentrations and data replicability of Cd, Cu, Hg, Pb and Zn measured during at least two exposure periods in environments affected by different degrees of contamination. The optimal choices for the studied aspects were the following: (i) Sphagnum denticulatum, (ii) 5.68 mg of moss tissue for each cm-2 of bag surface, (iii) 8 weeks of exposure, and (iv) 4 m height of exposure. Duration of exposure and height of exposure accounted for most of the variability in the data. The aim of this methodological study was to provide data to help establish a standardized protocol that will enable use of the moss bag technique by public authorities.

Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

Energy Technology Data Exchange (ETDEWEB)

Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E., E-mail: gantipas@metal.ntua.gr

2014-01-15

Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH){sub 3}·3H{sub 2}O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH){sub 3}(am) was stable with a solubility lower than 50 μg/l in the range 5.7 < pH < 11. • For mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3}, the stability region was extended to 4.8 < pH < 13.5. -- Abstract: Chromium is a common contaminant of soils and aquifers and constitutes a major environmental problem. In nature, chromium usually exists in the form of two oxidation states, trivalent, Cr(III), which is relatively innocuous for biota and for the aquatic environment, and hexavalent, Cr(VI) which is toxic, carcinogenic and very soluble. Accordingly, the majority of wastewater and groundwater treatment technologies, include a stage where Cr(VI) is reduced to Cr(III), in order to remove chromium from the aqueous phase and bind the element in the form of environmentally stable solid compounds. In the absence of iron the final product is typically of the form Cr(OH){sub 3}·xH{sub 2}O whereas in the presence of iron the precipitate is a mixed Fe{sub (1−x)}Cr{sub x}(OH){sub 3} phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe{sub x},Cr{sub 1−x})(OH){sub 3} hydroxides as compared to the stability of Cr(OH){sub 3}. We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH){sub 3}·3H{sub 2}O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH){sub 3}(am) phase. Mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3} hydroxides were found to be of the ferrihydrite structure, Fe(OH){sub 3}, and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe(III)–Cr(III

Structural Characterization of Am(III)- and Pu(III)-DOTA Complexes.

Science.gov (United States)

Audras, Matthieu; Berthon, Laurence; Berthon, Claude; Guillaumont, Dominique; Dumas, Thomas; Illy, Marie-Claire; Martin, Nicolas; Zilbermann, Israel; Moiseev, Yulia; Ben-Eliyahu, Yeshayahu; Bettelheim, Armand; Cammelli, Sebastiano; Hennig, Christoph; Moisy, Philippe

2017-10-16

The complexation of 1,4,7,10-tetrazacyclodecane-1,4,7,10-tetraacetic acid (DOTA) ligand with two trivalent actinides (Am 3+ and Pu 3+ ) was investigated by UV-visible spectrophotometry, NMR spectroscopy, and extended X-ray absorption fine structure in conjunction with computational methods. The complexation process of these two cations is similar to what has been previously observed with lanthanides(III) of similar ionic radius. The complexation takes place in different steps and ends with the formation of a (1:1) complex [(An(III)DOTA)(H 2 O)] - , where the cation is bonded to the nitrogen atoms of the ring, the four carboxylate arms, and a water molecule to complete the coordination sphere. The formation of An(III)-DOTA complexes is faster than the Ln(III)-DOTA systems of equivalent ionic radius. Furthermore, it is found that An-N distances are slightly shorter than Ln-N distances. Theoretical calculations showed that the slightly higher affinity of DOTA toward Am over Nd is correlated with slightly enhanced ligand-to-metal charge donation arising from oxygen and nitrogen atoms.

Survey Summary

Data.gov (United States)

U.S. Department of Health & Human Services — Nursing home summary information for the Health and Fire Safety Inspections currently listed on Nursing Home Compare, including dates of the three most recent...

Effects of a Combination Therapy of Sclerostin Antibody III and Raloxifene on Bone Formation Markers in Ovariectomized Rats

International Nuclear Information System (INIS)

Allam, H. I. G.

2016-01-01

Objective: To determine the systemic effect of sclerostin monoclonal antibody (Scl-AbIII) administration on markers of bone formation and compare it with a combination of sclerostin antibody and raloxifene. Study Design: Experimental study. Place and Duration of Study: Medical College Animal House at King Khaled University Hospital, Riyadh, Saudi Arabia, from January to November 2014. Methodology: Forty-five female rats were divided into 5 groups equally; 1 control group and 4 groups of ovariectomized (OVX) rats: control OVX rats and OVX rats treated by Scl-AbIII, raloxifene or Scl-AbIII+raloxifene one month after ovariectomy, continued for 4 weeks. At the end of treatment, serum levels of Bone Specific Alkaline Phosphatase (BSAP), alkaline phosphatase, osteocalcin, Insulin-like Growth Factor-1 (IGF-1), Parathyroid Hormone (PTH), Ca/sup 2+/ and phosphorus were measured. Uterus was weighed and body weight change was calculated. Results: Scl-AbIII or raloxifene treatment produced significant increase of serum BSAP, osteocalcin, IGF-1, PTH and Ca/sup 2+/ levels. Raloxifene, either alone or combined with Scl-AbIII attenuated the decrease in uterus wet weight, and the increase in body weight seen in OVX rats. Combination therapy of Scl-AbIII, and raloxifene produced significant increase of serum alkaline phosphatase, osteocalcin and IGF-1 levels than treatment with either Scl-AbIII or raloxifene alone. Conclusion: Combination therapy of Scl-AbIII and raloxifene is an attractive strategy to enhance bone formation and can offer better gain over treatment with either one of them alone. Confirmation of these preliminary observations must await careful long-term studies. (author)

Standards development status. Summary report

International Nuclear Information System (INIS)

1981-12-01

The Standards Development Status Summary Report is designed for scheduling, monitoring, and controlling the process by which Regulatory Standards, Guides, Reports, Petitions, and Environmental Statements are written. It is a summary of the current schedule plans for development of the above products

Synthesis, structure, luminescent, and magnetic properties of carbonato-bridged Zn(II)2Ln(III)2 complexes [(μ4-CO3)2{Zn(II)L(n)Ln(III)(NO3)}2] (Ln(III) = Gd(III), Tb(III), Dy(III); L(1) = N,N'-bis(3-methoxy-2-oxybenzylidene)-1,3-propanediaminato, L(2) = N,N'-bis(3-ethoxy-2-oxybenzylidene)-1,3-propanediaminato).

Science.gov (United States)

Ehama, Kiyomi; Ohmichi, Yusuke; Sakamoto, Soichiro; Fujinami, Takeshi; Matsumoto, Naohide; Mochida, Naotaka; Ishida, Takayuki; Sunatsuki, Yukinari; Tsuchimoto, Masanobu; Re, Nazzareno

2013-11-04

Carbonato-bridged Zn(II)2Ln(III)2 complexes [(μ4-CO3)2{Zn(II)L(n)Ln(III)(NO3)}2]·solvent were synthesized through atmospheric CO2 fixation reaction of [Zn(II)L(n)(H2O)2]·xH2O, Ln(III)(NO3)3·6H2O, and triethylamine, where Ln(III) = Gd(III), Tb(III), Dy(III); L(1) = N,N'-bis(3-methoxy-2-oxybenzylidene)-1,3-propanediaminato, L(2) = N,N'-bis(3-ethoxy-2-oxybenzylidene)-1,3-propanediaminato. Each Zn(II)2Ln(III)2 structure possessing an inversion center can be described as two di-μ-phenoxo-bridged {Zn(II)L(n)Ln(III)(NO3)} binuclear units bridged by two carbonato CO3(2-) ions. The Zn(II) ion has square pyramidal coordination geometry with N2O2 donor atoms of L(n) and one oxygen atom of a bridging carbonato ion at the axial site. Ln(III) ion is coordinated by nine oxygen atoms consisting of four from the deprotonated Schiff-base L(n), two from a chelating nitrate, and three from two carbonate groups. The temperature-dependent magnetic susceptibilities in the range 1.9-300 K, field-dependent magnetization from 0 to 5 T at 1.9 K, and alternating current magnetic susceptibilities under the direct current bias fields of 0 and 1000 Oe were measured. The magnetic properties of the Zn(II)2Ln(III)2 complexes are analyzed on the basis of the dicarbonato-bridged binuclear Ln(III)-Ln(III) structure, as the Zn(II) ion with d(10) electronic configuration is diamagnetic. ZnGd1 (L(1)) and ZnGd2 (L(2)) show a ferromagnetic Gd(III)-Gd(III) interaction with J(Gd-Gd) = +0.042 and +0.028 cm(-1), respectively, on the basis of the Hamiltonian H = -2J(Gd-Gd)ŜGd1·ŜGd2. The magnetic data of the Zn(II)2Ln(III)2 complexes (Ln(III) = Tb(III), Dy(III)) were analyzed by a spin Hamiltonian including the crystal field effect on the Ln(III) ions and the Ln(III)-Ln(III) magnetic interaction. The Stark splitting of the ground state was so evaluated, and the energy pattern indicates a strong easy axis (Ising type) anisotropy. Luminescence spectra of Zn(II)2Tb(III)2 complexes were observed, while those

WISC-III e WAIS-III na avaliação da inteligência de cegos WISC-III/WAIS-III en ciegos WISC-III and WAIS-III in intellectual assessment of blind people

OpenAIRE

Elizabeth do Nascimento; Carmen Elvira Flores-Mendoza

2007-01-01

Diante da escassez de pesquisas nacionais e de testes psicológicos destinados a avaliar pessoas cegas, desenvolveu-se um estudo psicométrico com as escalas verbais dos testes WISC-III e WAIS-III. Após as adaptações de alguns estímulos e das instruções, os testes foram aplicados em crianças (N = 120) e adultos (N = 52) residentes em Belo Horizonte. Os resultados indicaram que as escalas verbais modificadas apresentam uma boa consistência interna (alfa> 0,80). Além disso, a investigação da vali...

Richard III

DEFF Research Database (Denmark)

Lauridsen, Palle Schantz

2017-01-01

Kort analyse af Shakespeares Richard III med fokus på, hvordan denne skurk fremstilles, så tilskuere (og læsere) langt henad vejen kan føle sympati med ham. Med paralleller til Netflix-serien "House of Cards"......Kort analyse af Shakespeares Richard III med fokus på, hvordan denne skurk fremstilles, så tilskuere (og læsere) langt henad vejen kan føle sympati med ham. Med paralleller til Netflix-serien "House of Cards"...

NMR and TRLFS studies of Ln(iii) and An(iii) C5-BPP complexes.

Science.gov (United States)

Adam, Christian; Beele, Björn B; Geist, Andreas; Müllich, Udo; Kaden, Peter; Panak, Petra J

2015-02-01

C5-BPP is a highly efficient N-donor ligand for the separation of trivalent actinides, An(iii), from trivalent lanthanides, Ln(iii). The molecular origin of the selectivity of C5-BPP and many other N-donor ligands of the BTP-type is still not entirely understood. We present here the first NMR studies on C5-BPP Ln(iii) and An(iii) complexes. C5-BPP is synthesized with 10% 15 N labeling and characterized by NMR and LIFDI-MS methods. 15 N NMR spectroscopy gives a detailed insight into the bonding of C5-BPP with lanthanides and Am(iii) as a representative for trivalent actinide cations, revealing significant differences in 15 N chemical shift for coordinating nitrogen atoms compared to Ln(iii) complexes. The temperature dependence of NMR chemical shifts observed for the Am(iii) complex indicates a weak paramagnetism. This as well as the observed large chemical shift for coordinating nitrogen atoms show that metal-ligand bonding in Am(C5-BPP) 3 has a larger share of covalence than in lanthanide complexes, confirming earlier studies. The Am(C5-BPP) 3 NMR sample is furthermore spiked with Cm(iii) and characterized by time-resolved laser fluorescence spectroscopy (TRLFS), yielding important information on the speciation of trace amounts of minor complex species.

12 CFR 1805.101 - Summary.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Summary. 1805.101 Section 1805.101 Banks and Banking COMMUNITY DEVELOPMENT FINANCIAL INSTITUTIONS FUND, DEPARTMENT OF THE TREASURY COMMUNITY DEVELOPMENT FINANCIAL INSTITUTIONS PROGRAM General Provisions § 1805.101 Summary. Under the Community...

Separation by liquid-liquid extraction of actinides(III) from lanthanides(III) using new molecules: the picolinamides; Separation par extraction liquide-liquide des actinides(III) des lanthanides(III) par de nouvelles molecules: les picolinamides

Energy Technology Data Exchange (ETDEWEB)

Cordier, P Y [CEA Marcoule, Departement de Recherche en Retraitement et en Vitrification, 30 - Bagnols-sur-Ceze (France); [Clermont-Ferrand-2 Univ., 63 - Aubiere (France)

1996-07-01

In the field of long-lived radionuclides separation from waste generated during spent fuel reprocessing, the picolinamides have been chosen as potential extractants for the selective extraction of actinides (III) from lanthanides (III). The first studies initiated on the most simple molecule of the picolinamide family, namely 2-pyridinecarboxamide, pointed out that in an aqueous media the complexation stability constant between this ligand and Am(III) is roughly 10 times higher than the ones corresponding to Ln(III). The synthesis of lipophilic derivatives of 2-pyridinecarboxamide leaded to extraction experiments. The extraction of metallic cation by lipophilic picolinamides, according to a solvatation mechanism, is strongly dependent on the nature of the amide function: a primary amide function (group I) leads to a good extraction; on the contrary, there is a decrease for secondary (group II) and tertiary (group III) amide functions. From a theoretical point of view, this work leads finally to the following conclusions: confirmation of the importance of the presence of soft donor atoms within the extractants (nitrogen in our case) for An(III)/Ln(III). Also, sensitivity of this soft donor atom regarding the protonation reaction; prevalence in our case of the affinity of the extractant for the metallic cation over the lipophilia of the extractant to ensure good distribution coefficients. The extraction and Am(III)/Ln(III) separation performances of the picolinamides from pertechnetic media leads to the design of a possible flowsheet for the reprocessing of high level liquid waste, with the new idea of an integrated technetium reflux. (author) 105 refs.

Extraction behaviour of Am(III) and Eu(III) from nitric acid medium in TEHDGA-HDEHP impregnated resins

Energy Technology Data Exchange (ETDEWEB)

Saipriya, G.; Kumar, T. [Bhabha Atomic Research Centre Facilities, Kalpakkam (India). Kalpakkam Reprocessing Plant; Kumaresan, R.; Nayak, P.K.; Venkatesan, K.A.; Antony, M.P. [Indira Gandhi Center for Atomic Research, Kalpakkam (India). Fuel Chemistry Div.

2016-07-01

The extraction behaviour of Am(III) and Eu(III) from nitric acid medium was studied in the solvent impregnated resins containing extractants such as tetra-bis(2-ethylhexyl)diglycolamide (TEHDGA) or bis-(2-ethylhexyl)phosphoric acid (HDEHP) or mixture of TEHDGA+HDEHP. The rate of extraction of Am(III) and Eu(III) from 1 M nitric acid and the effect of various parameters, such as the concentration of nitric acid in aqueous phase and concentration of TEHDGA and HDEHP in resin phase, on the distribution coefficient of Am(III) and Eu(III) was studied. The distribution coefficient of Am(III) and Eu(III) in HDEHP-impregnated resin decreased and that in TEHDGA-impregnated resin increased, with increase in the concentration of nitric acid. However, in (TEHDGA+HDEHP) - impregnated resin, synergic extraction was observed at lower nitric acid concentration and antagonism at higher nitric acid concentration. The mechanism of Am(III) and Eu(III) extraction in the combined resin was investigated by slope analysis method. The extraction of various metal ions present in the fast reactor simulated high-level liquid waste was studied. The separation factor of Am(III) over Eu(III) was studied using citrate-buffered diethylenetriaminepentaacetic acid (DTPA) solution.

Characterization of the lanthanum(III) and europium(III) trichloroacetate complexes extracted with 18-crown-6

International Nuclear Information System (INIS)

Imura, H.; Saito, Y.; Ohashi, K.; Meguro, Y.; Yoshida, Z.; Choppin, G.R.

1996-01-01

Extraction of lanthanide(III) ions with 18-crown-6 (18C6) and trichloroacetate (tca) has been studied. The composition, hydration, and structure of the La(III) and Eu(III) complexes extracted into 1,2-dichloroethane were investigated by using several methods such as the liquid-liquid distribution technique, conductimetry, Karl Fisher titration, laser luminescence spectroscopy, and 1 H NMR. The La(III) complex was found to be a monohydrate, La(tca) 3 (18C6)(H 2 O), while that of Eu(III) was a mixture of a monohydrate and a dihydrate, i.e., Eu(tca) 3 (18C6)(H 2 O) and Eu(tca) 3 (18C6)(H 2 O) 2 . The origin of the selectivity by 18C6 which gives much higher extractability of La(III) than of Eu(III) is explained by considering the hydration and probable structure of their complexes. 12 refs., 5 figs., 4 tabs

Conference Summary

International Nuclear Information System (INIS)

Tinkham, M.

1991-01-01

This summary will begin with short remarks, trying to recall some of the spirit of the presentations of each of the speakers during the first day, with no attempt at detail or completeness, given the need for a 20:1 compression relative to the original talk. The author hopes these idiosyncratic recollections do not infuriate the speakers too much. Since the speakers on the second day presented such interlocking topics, he simply tries to present some sort of consensus report, to which he adds some comments of his own. The two talks preceding this Summary on the final day dealt with the prospects for applications; since he had no chance to attempt to prepare a proper report on these, he says only a few words about those presentations

Purification of chicken carbonic anhydrase isozyme-III (CA-III) and its measurement in White Leghorn chickens.

Science.gov (United States)

Nishita, Toshiho; Tomita, Yuichiro; Yorifuji, Daisuke; Orito, Kensuke; Ochiai, Hideharu; Arishima, Kazuyosi

2011-11-26

The developmental profile of chicken carbonic anhydrase-III (CA-III) blood levels has not been previously determined or reported. We isolated CA-III from chicken muscle and investigated age-related changes in the levels of CA-III in blood. CA-III was purified from chicken muscle. The levels of CA-III in plasma and erythrocytes from 278 female chickens (aged 1-93 weeks) and 68 male chickens (aged 3-59 weeks) were determined by ELISA. The mean level of CA-III in female chicken erythrocytes (1 week old) was 4.6 μg/g of Hb, and the CA-III level did not change until 16 weeks of age. The level then increased until 63 weeks of age (11.8 μg/g of Hb), decreased to 4.7 μg/g of Hb at 73 weeks of age, and increased again until 93 weeks of age (8.6 μg/g of Hb). The mean level of CA-III in erythrocytes from male chickens (3 weeks old) was 2.4 μg/g of Hb, and this level remained steady until 59 weeks of age. The mean plasma level of CA-III in 1-week-old female chickens was 60 ng/mL, and this level was increased at 3 weeks of age (141 ng/mL) and then remained steady until 80 weeks of age (122 ng/mL). The mean plasma level of CA-III in 3-week-old male chickens was 58 ng/mL, and this level remained steady until 59 weeks of age. We observed both developmental changes and sex differences in CA-III concentrations in White Leghorn (WL) chicken erythrocytes and plasma. Simple linear regression analysis showed a significant association between the erythrocyte CA-III level and egg-laying rate in WL-chickens 16-63 weeks of age (p < 0.01).

International Conference Modern Stochastics: Theory and Applications III

CERN Document Server

Limnios, Nikolaos; Mishura, Yuliya; Sakhno, Lyudmyla; Shevchenko, Georgiy; Modern Stochastics and Applications

2014-01-01

This volume presents an extensive overview of all major modern trends in applications of probability and stochastic analysis. It will be a  great source of inspiration for designing new algorithms, modeling procedures, and experiments. Accessible to researchers, practitioners, as well as graduate and postgraduate students, this volume presents a variety of new tools, ideas, and methodologies in the fields of optimization, physics, finance, probability, hydrodynamics, reliability, decision making, mathematical finance, mathematical physics, and economics. Contributions to this Work include those of selected speakers from the international conference entitled “Modern Stochastics: Theory and Applications III,”  held on September 10 –14, 2012 at Taras Shevchenko National University of Kyiv, Ukraine. The conference covered the following areas of research in probability theory and its applications: stochastic analysis, stochastic processes and fields, random matrices, optimization methods in probability, st...

Development and evaluation of clicker methodology for introductory physics courses

Science.gov (United States)

Lee, Albert H.

Many educators understand that lectures are cost effective but not learning efficient, so continue to search for ways to increase active student participation in this traditionally passive learning environment. In-class polling systems, or "clickers", are inexpensive and reliable tools allowing students to actively participate in lectures by answering multiple-choice questions. Students assess their learning in real time by observing instant polling summaries displayed in front of them. This in turn motivates additional discussions which increase the opportunity for active learning. We wanted to develop a comprehensive clicker methodology that creates an active lecture environment for a broad spectrum of students taking introductory physics courses. We wanted our methodology to incorporate many findings of contemporary learning science. It is recognized that learning requires active construction; students need to be actively involved in their own learning process. Learning also depends on preexisting knowledge; students construct new knowledge and understandings based on what they already know and believe. Learning is context dependent; students who have learned to apply a concept in one context may not be able to recognize and apply the same concept in a different context, even when both contexts are considered to be isomorphic by experts. On this basis, we developed question sequences, each involving the same concept but having different contexts. Answer choices are designed to address students preexisting knowledge. These sequences are used with the clickers to promote active discussions and multiple assessments. We have created, validated, and evaluated sequences sufficient in number to populate all of introductory physics courses. Our research has found that using clickers with our question sequences significantly improved student conceptual understanding. Our research has also found how to best measure student conceptual gain using research-based instruments

Generating Concise Natural Language Summaries.

Science.gov (United States)

McKeown, Kathleen; And Others

1995-01-01

Presents an approach to summarization that combines information from multiple facts into a single sentence using linguistic constructions. Describes two applications: one produces summaries of basketball games, and the other contains summaries of telephone network planning activity. Both summarize input data as opposed to full text. Discusses…

Creating and evaluating a new clicker methodology

Science.gov (United States)

Li, Pengfei

comparing clicker lecture sections using the new methodology to lecture sections with a similar population of students taught without clickers in a traditional manner. The results of this test were summarized in chapter 5. Chapter 6 contains a brief summary of research results and conclusions, together with an overview of future efforts in the OSU clicker project.

Extraction and stripping of neodymium (III) and dysprosium (III) by TRUEX solvent

International Nuclear Information System (INIS)

Rout, Alok; Venkatesan, K.A.; Antony, M.P.; Srinivasan, T.G.; Vasudeva Rao, P.R.

2009-01-01

McCabe-Thiele diagram for the extraction and stripping of Nd (III) and Dy (III) by TRUEX solvent has been constructed to determine the number of stages required for complete extraction and stripping. (author)

Insight into the Extraction Mechanism of Americium(III) over Europium(III) with Pyridylpyrazole: A Relativistic Quantum Chemistry Study.

Science.gov (United States)

Kong, Xiang-He; Wu, Qun-Yan; Wang, Cong-Zhi; Lan, Jian-Hui; Chai, Zhi-Fang; Nie, Chang-Ming; Shi, Wei-Qun

2018-05-10

Separation of trivalent actinides (An(III)) and lanthanides (Ln(III)) is one of the most important steps in spent nuclear fuel reprocessing. However, it is very difficult and challenging to separate them due to their similar chemical properties. Recently the pyridylpyrazole ligand (PypzH) has been identified to show good separation ability toward Am(III) over Eu(III). In this work, to explore the Am(III)/Eu(III) separation mechanism of PypzH at the molecular level, the geometrical structures, bonding nature, and thermodynamic behaviors of the Am(III) and Eu(III) complexes with PypzH ligands modified by alkyl chains (Cn-PypzH, n = 2, 4, 8) have been systematically investigated using scalar relativistic density functional theory (DFT). According to the NBO (natural bonding orbital) and QTAIM (quantum theory of atoms in molecules) analyses, the M-N bonds exhibit a certain degree of covalent character, and more covalency appears in Am-N bonds compared to Eu-N bonds. Thermodynamic analyses suggest that the 1:1 extraction reaction, [M(NO 3 )(H 2 O) 6 ] 2+ + PypzH + 2NO 3 - → M(PypzH)(NO 3 ) 3 (H 2 O) + 5H 2 O, is the most suitable for Am(III)/Eu(III) separation. Furthermore, the extraction ability and the Am(III)/Eu(III) selectivity of the ligand PypzH is indeed enhanced by adding alkyl-substituted chains in agreement with experimental observations. Besides this, the nitrogen atom of pyrazole ring plays a more significant role in the extraction reactions related to Am(III)/Eu(III) separation compared to that of pyridine ring. This work could identify the mechanism of the Am(III)/Eu(III) selectivity of the ligand PypzH and provide valuable theoretical information for achieving an efficient Am(III)/Eu(III) separation process for spent nuclear fuel reprocessing.

Meteorological Summaries

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Multi-year summaries of one or more meteorological elements at a station or in a state. Primarily includes Form 1078, a United States Weather Bureau form designed...

Sexual Harassment and Organizational Outcomes Executive Summary

Science.gov (United States)

2011-10-01

quid pro quo type of Sexual harassment and Organizational, 4 sexual harassment (e.g., sexual coercion). This should drive organizational efforts to... Sexual Harassment and Organizational Outcomes Executive Summary Charlie L. Law DEFENSE EQUAL...Executive Summary] No. 99-11 Sexual harassment and Organizational, 2 Executive Summary Issue

An extensible six-step methodology to automatically generate fuzzy DSSs for diagnostic applications.

Science.gov (United States)

d'Acierno, Antonio; Esposito, Massimo; De Pietro, Giuseppe

2013-01-01

The diagnosis of many diseases can be often formulated as a decision problem; uncertainty affects these problems so that many computerized Diagnostic Decision Support Systems (in the following, DDSSs) have been developed to aid the physician in interpreting clinical data and thus to improve the quality of the whole process. Fuzzy logic, a well established attempt at the formalization and mechanization of human capabilities in reasoning and deciding with noisy information, can be profitably used. Recently, we informally proposed a general methodology to automatically build DDSSs on the top of fuzzy knowledge extracted from data. We carefully refine and formalize our methodology that includes six stages, where the first three stages work with crisp rules, whereas the last three ones are employed on fuzzy models. Its strength relies on its generality and modularity since it supports the integration of alternative techniques in each of its stages. The methodology is designed and implemented in the form of a modular and portable software architecture according to a component-based approach. The architecture is deeply described and a summary inspection of the main components in terms of UML diagrams is outlined as well. A first implementation of the architecture has been then realized in Java following the object-oriented paradigm and used to instantiate a DDSS example aimed at accurately diagnosing breast masses as a proof of concept. The results prove the feasibility of the whole methodology implemented in terms of the architecture proposed.

Hydration structure of Ti(III) and Cr(III): Monte Carlo simulation ...

African Journals Online (AJOL)

Classical Monte Carlo simulations were performed to investigate the solvation structures of Ti(III) and Cr(III) ions in water with only ion-water pair interaction potential and by including three-body correction terms. The hydration structures were evaluated in terms of radial distribution functions, coordination numbers and ...

Model summary report for the safety assessment SR-Site

International Nuclear Information System (INIS)

Vahlund, Fredrik; Zetterstroem Evins, Lena; Lindgren, Maria

2010-12-01

This document is the model summary report for the safety assessment SR-Site. In the report, the quality assurance (QA) measures conducted for assessment codes are presented together with the chosen QA methodology. In the safety assessment project SR-Site, a large number of numerical models are used to analyse the system and to show compliance. In order to better understand how the different models interact and how information are transferred between the different models Assessment Model Flowcharts, AMFs, are used. From these, different modelling tasks can be identify and the computer codes used. As a large number of computer codes are used in the assessment the complexity of these differs to a large extent, some of the codes are commercial while others are developed especially for the assessment at hand. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined for all codes: - It must be demonstrated that the code is suitable for its purpose. - It must be demonstrated that the code has been properly used. - It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. - It must be described how data are transferred between the different computational tasks. Although the requirements are identical for all codes in the assessment, the measures used to show that the requirements are fulfilled will be different for different types of codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented together with a discussion on how the requirements are met

Model summary report for the safety assessment SR-Site

Energy Technology Data Exchange (ETDEWEB)

Vahlund, Fredrik; Zetterstroem Evins, Lena (Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)); Lindgren, Maria (Kemakta Konsult AB, Stockholm (Sweden))

2010-12-15

This document is the model summary report for the safety assessment SR-Site. In the report, the quality assurance (QA) measures conducted for assessment codes are presented together with the chosen QA methodology. In the safety assessment project SR-Site, a large number of numerical models are used to analyse the system and to show compliance. In order to better understand how the different models interact and how information are transferred between the different models Assessment Model Flowcharts, AMFs, are used. From these, different modelling tasks can be identify and the computer codes used. As a large number of computer codes are used in the assessment the complexity of these differs to a large extent, some of the codes are commercial while others are developed especially for the assessment at hand. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined for all codes: - It must be demonstrated that the code is suitable for its purpose. - It must be demonstrated that the code has been properly used. - It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. - It must be described how data are transferred between the different computational tasks. Although the requirements are identical for all codes in the assessment, the measures used to show that the requirements are fulfilled will be different for different types of codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented together with a discussion on how the requirements are met

12 CFR 1806.101 - Summary.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Summary. 1806.101 Section 1806.101 Banks and Banking COMMUNITY DEVELOPMENT FINANCIAL INSTITUTIONS FUND, DEPARTMENT OF THE TREASURY BANK ENTERPRISE AWARD PROGRAM General Provisions § 1806.101 Summary. (a) Under the Bank Enterprise Award Program, the...

Site environmental report summary

International Nuclear Information System (INIS)

1992-01-01

In this summary of the Fernald 1992 Site Environmental Report the authors will describe the impact of the Fernald site on man and the environment and provide results from the ongoing Environmental Monitoring Program. Also included is a summary of the data obtained from sampling conducted to determine if the site complies with DOE, US Environmental Protection Agency (USEPA), and Ohio EPA (OEPA) requirements. These requirements are set to protect both man and the environment

19 CFR 151.41 - Information on entry summary.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Information on entry summary. 151.41 Section 151... Products § 151.41 Information on entry summary. On the entry summary for petroleum or petroleum products in.... If the exact volumetric quantity cannot be determined in advance, the entry summary may be made for...

FT4 Data Analysis Summary (SSI-ARC)

Science.gov (United States)

Isaacson, Douglas R.; Gong, Chester; Reardon, Scott Edward; Santiago, Confesor

2016-01-01

Standards for Unmanned Aircraft System (UAS) Detect-and-Avoid (DAA) systems are currently being developed under the auspices of the RTCA Special Committee 228 (SC-228). To support the development of these standards, a series of flight tests has been conducted at NASAs Armstrong Flight Research Center (NASA-AFRC). The fourth in this series of flight test activities (Flight Test 4, or simply FT4) was conducted during the Spring and Summer of 2016. FT4 supported the objectives of numerous organizations working toward UAS DAA Minimum Operational Performance Standards (MOPS) and UAS DAA Radar MOPS. The summary provided herein is limited to the objectives, analysis and conclusions of the NASA Ames Research Center (NASA-ARC) SSI team toward the refinement of UAS DAA MOPS. This document provides a high-level overview of FT4 and the SSI-ARC objectives, a summary of the data analysis methodology and recommendations for UAS DAA MOPS refinements based on the data analysis results. A total of 72 encounters were flown to support SSI-ARC objectives. Test results were generally consistent with acceptable UAS DAA system performance and will be considered in broader SC-228 requirements validation efforts. Observed alert lead times indicated acceptable UAS DAA alerting performance. Effective interoperability between the UAS DAA system and the Traffic Alert and Collision Avoidance System (TCAS) was observed with one notable exception: TCAS Resolutions Advisories (RA) were observed in the absence of any DAA alert on two occasions, indicating the need for alert parameter refinement. Findings further indicated the need for continued work in the areas of DAA Well Clear Recovery logic and alert stability for Mode-C-only intruders. Finally, results demonstrated a high level of compliance with a set of evaluation criteria designed to provide anecdotal evidence of acceptable UAS DAA system performance.

VideoSET: Video Summary Evaluation through Text

OpenAIRE

Yeung, Serena; Fathi, Alireza; Fei-Fei, Li

2014-01-01

In this paper we present VideoSET, a method for Video Summary Evaluation through Text that can evaluate how well a video summary is able to retain the semantic information contained in its original video. We observe that semantics is most easily expressed in words, and develop a text-based approach for the evaluation. Given a video summary, a text representation of the video summary is first generated, and an NLP-based metric is then used to measure its semantic distance to ground-truth text ...

Extraction Separation of Am(III) and Eu(III) with Thermo-sensitive Gel introducing TPEN Derivatives

International Nuclear Information System (INIS)

Kenji Takeshita; Yoshio Nakano; Tatsuro Matsumura; Atsunori Mori

2008-01-01

A thermal-swing chromatographic process using a thermo-sensitive gel co-polymerized with NIPA (N-isopropyl-acrylamide) and TPPEN (N,N,N',N'-tetrakis(4-propenyl-oxy-2-pyridyl-methyl)ethylenediamine) was studied for the separation of Am(III) from Eu(III). First, the radiolysis of the TPPEN-NIPA gel was tested by the γ-ray irradiation and the α nuclide adsorption. The extraction separation of Am(III) was not influenced in the radioactive environment of the proposed process. Next, the TPPEN-NIPA gel was immobilized in porous silica particles and the applicability of the gel-immobilized silica to the proposed process was tested. Am(III) was extracted selectively in the gel-immobilized silica at 5 deg. C and the separation factor of Am(III) over Eu(III) was evaluated to be 3.7. The distribution ratio of Am(III) was reduced to less than 1/20 by increasing temperature from 5 deg. C to 40 deg. C. These results indicate that the TPPEN-NIPA gel is applicable to the thermal-swing chromatographic process for the minor actinide recovery. (authors)

Impacts of Outer Continental Shelf (OCS) development on recreation and tourism. Volume 3. Detailed methodology

Energy Technology Data Exchange (ETDEWEB)

1987-04-01

The final report for the project is presented in five volumes. This volume, Detailed Methodology Review, presents a discussion of the methods considered and used to estimate the impacts of Outer Continental Shelf (OCS) oil and gas development on coastal recreation in California. The purpose is to provide the Minerals Management Service with data and methods to improve their ability to analyze the socio-economic impacts of OCS development. Chapter II provides a review of previous attempts to evaluate the effects of OCS development and of oil spills on coastal recreation. The review also discusses the strengths and weaknesses of different approaches and presents the rationale for the methodology selection made. Chapter III presents a detailed discussion of the methods actually used in the study. The volume contains the bibliography for the entire study.

Model summary report for the safety assessment SFR 1 SAR-08

Energy Technology Data Exchange (ETDEWEB)

2008-03-15

This document is the model summary report for the safety assessment SFR 1 SAR-08. In the report, the quality assurance measures conducted for the assessment codes are presented together with the chosen methodology. In the safety assessment SFR1 SAR-08, a number of different computer codes are used. In order to better understand how these codes are related an Assessment Model Flowchart, AMF, has been produced within the project. From the AMF, it is possible to identify the different modelling tasks and consequently also the different computer codes used. A number of different computer codes are used in the assessment of which some are commercial while others are developed for assessment projects. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined: - It must be demonstrated that the code is suitable for its purpose. - It must be demonstrated that the code has been properly used. - It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. Although the requirements are identical for all codes, the measures used to show that the requirements are fulfilled will be different for different codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented and it is shown how the requirements are met

Model summary report for the safety assessment SFR 1 SAR-08

International Nuclear Information System (INIS)

2008-03-01

This document is the model summary report for the safety assessment SFR 1 SAR-08. In the report, the quality assurance measures conducted for the assessment codes are presented together with the chosen methodology. In the safety assessment SFR1 SAR-08, a number of different computer codes are used. In order to better understand how these codes are related an Assessment Model Flowchart, AMF, has been produced within the project. From the AMF, it is possible to identify the different modelling tasks and consequently also the different computer codes used. A number of different computer codes are used in the assessment of which some are commercial while others are developed for assessment projects. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined: - It must be demonstrated that the code is suitable for its purpose. - It must be demonstrated that the code has been properly used. - It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. Although the requirements are identical for all codes, the measures used to show that the requirements are fulfilled will be different for different codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented and it is shown how the requirements are met

Variation in plasmonic (electronic) spectral parameters of Pr (III) and Nd (III) with varied concentration of moderators

Energy Technology Data Exchange (ETDEWEB)

Mishra, Shubha, E-mail: shubhamishra03@gmail.com [School of Studies in Physics, Vikram University, Ujjain (M. P.) (India); Limaye, S. N., E-mail: snl222@yahoo.co.in [Department of Chemistry, Dr. H.S. Gour University, A Central University, Sagar (M.P.) (India)

2015-07-31

It is said that the -4f shells behave as core and are least perturbed by changes around metal ion surrounding. However, there are evidences that-4f shells partially involved in direct moderator interaction. A systematic investigation on the plasmonic (electronic) spectral studies of some Rare Earths[RE(III).Mod] where, RE(III) = Pr(III),Nd(III) and Mod(moderator) = Y(III),La(III),Gd(III) and Lu(III), increased moderator concentration from 0.01 mol dm{sup −3} to 0.025 mol dm{sup −3} keeping the metal ion concentration at 0.01mol dm{sup −3} have been carried out. Variations in oscillator strengths (f), Judd-Ofelt parameters (T{sub λ}),inter-electronic repulsion Racah parameters (δE{sup k}),nephelauxetic ratio (β), radiative parameters (S{sub ED},A{sub T},β{sub R},T{sub R}). The values of oscillator strengths and Judd-Ofelt parameters have been discussed in the light of coordination number of RE(III) metal ions, denticity and basicity of the moderators. The [RE(III).Mod] bonding pattern has been studies in the light of the change in Racah parameters and nephelauxetic ratio.

Purification of chicken carbonic anhydrase isozyme-III (CA-III and its measurement in White Leghorn chickens

Directory of Open Access Journals (Sweden)

Nishita Toshiho

2011-11-01

Full Text Available Abstract Background The developmental profile of chicken carbonic anhydrase-III (CA-III blood levels has not been previously determined or reported. We isolated CA-III from chicken muscle and investigated age-related changes in the levels of CA-III in blood. Methods CA-III was purified from chicken muscle. The levels of CA-III in plasma and erythrocytes from 278 female chickens (aged 1-93 weeks and 68 male chickens (aged 3-59 weeks were determined by ELISA. Results The mean level of CA-III in female chicken erythrocytes (1 week old was 4.6 μg/g of Hb, and the CA-III level did not change until 16 weeks of age. The level then increased until 63 weeks of age (11.8 μg/g of Hb, decreased to 4.7 μg/g of Hb at 73 weeks of age, and increased again until 93 weeks of age (8.6 μg/g of Hb. The mean level of CA-III in erythrocytes from male chickens (3 weeks old was 2.4 μg/g of Hb, and this level remained steady until 59 weeks of age. The mean plasma level of CA-III in 1-week-old female chickens was 60 ng/mL, and this level was increased at 3 weeks of age (141 ng/mL and then remained steady until 80 weeks of age (122 ng/mL. The mean plasma level of CA-III in 3-week-old male chickens was 58 ng/mL, and this level remained steady until 59 weeks of age. Conclusion We observed both developmental changes and sex differences in CA-III concentrations in White Leghorn (WL chicken erythrocytes and plasma. Simple linear regression analysis showed a significant association between the erythrocyte CA-III level and egg-laying rate in WL-chickens 16-63 weeks of age (p

Assessing the impact of healthcare research: A systematic review of methodological frameworks.

Directory of Open Access Journals (Sweden)

Samantha Cruz Rivera

2017-08-01

Full Text Available Increasingly, researchers need to demonstrate the impact of their research to their sponsors, funders, and fellow academics. However, the most appropriate way of measuring the impact of healthcare research is subject to debate. We aimed to identify the existing methodological frameworks used to measure healthcare research impact and to summarise the common themes and metrics in an impact matrix.Two independent investigators systematically searched the Medical Literature Analysis and Retrieval System Online (MEDLINE, the Excerpta Medica Database (EMBASE, the Cumulative Index to Nursing and Allied Health Literature (CINAHL+, the Health Management Information Consortium, and the Journal of Research Evaluation from inception until May 2017 for publications that presented a methodological framework for research impact. We then summarised the common concepts and themes across methodological frameworks and identified the metrics used to evaluate differing forms of impact. Twenty-four unique methodological frameworks were identified, addressing 5 broad categories of impact: (1 'primary research-related impact', (2 'influence on policy making', (3 'health and health systems impact', (4 'health-related and societal impact', and (5 'broader economic impact'. These categories were subdivided into 16 common impact subgroups. Authors of the included publications proposed 80 different metrics aimed at measuring impact in these areas. The main limitation of the study was the potential exclusion of relevant articles, as a consequence of the poor indexing of the databases searched.The measurement of research impact is an essential exercise to help direct the allocation of limited research resources, to maximise research benefit, and to help minimise research waste. This review provides a collective summary of existing methodological frameworks for research impact, which funders may use to inform the measurement of research impact and researchers may use to inform

Methodologies for uncertainty analysis in the level 2 PSA and their implementation procedures

International Nuclear Information System (INIS)

Ahn, Kwang Il; Yang, Joon Eun; Kim, Dong Ha

2002-04-01

Main purpose of this report to present standardized methodologies for uncertainty analysis in the Level 2 Probabilistic Safety Assessment (PSA) and their implementation procedures, based on results obtained through a critical review of the existing methodologies for the analysis of uncertainties employed in the Level 2 PSA, especially Accident Progression Event Tree (APET). Uncertainties employed in the Level 2 PSA, quantitative expressions of overall knowledge of analysts' and experts' participating in the probabilistic quantification process of phenomenological accident progressions ranging from core melt to containment failure, their numerical values are directly related to the degree of confidence that the analyst has that a given phenomenological event or accident process will or will not occur, or analyst's subjective probabilities of occurrence. These results that are obtained from Level 2 PSA uncertainty analysis, become an essential contributor to the plant risk, in addition to the Level 1 PSA and Level 3 PSA uncertainties. Uncertainty analysis methodologies and their implementation procedures presented in this report was prepared based on the following criteria: 'uncertainty quantification process must be logical, scrutable, complete, consistent and in an appropriate level of detail, as mandated by the Level 2 PSA objectives'. For the aforementioned purpose, this report deals mainly with (1) summary of general or Level 2 PSA specific uncertainty analysis methodologies, (2) selection of phenomenological branch events for uncertainty analysis in the APET, methodology for quantification of APET uncertainty inputs and its implementation procedure, (3) statistical propagation of uncertainty inputs through APET and its implementation procedure, and (4) formal procedure for quantification of APET uncertainties and source term categories (STCs) through the Level 2 PSA quantification codes

41 CFR 60-2.31 - Program summary.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 1 2010-07-01 2010-07-01 true Program summary. 60-2.31...-AFFIRMATIVE ACTION PROGRAMS Miscellaneous § 60-2.31 Program summary. The affirmative action program must be summarized and updated annually. The program summary must be prepared in a format which will be prescribed by...

The Berlin 2016 process: a summary of methodology for the 5th International Consensus Conference on Concussion in Sport.

Science.gov (United States)

Meeuwisse, Willem H; Schneider, Kathryn J; Dvořák, Jiří; Omu, Onutobor Tobi; Finch, Caroline F; Hayden, K Alix; McCrory, Paul

2017-06-01

The purpose of this paper is to summarise the methodology for the 5th International Consensus Conference on Concussion in Sport. The 18 months of preparation included engagement of a scientific committee, an expert panel of 33 individuals in the field of concussion and a modified Delphi technique to determine the primary questions to be answered. The methodology also involved the writing of 12 systematic reviews to inform the consensus conference and submission and review of scientific abstracts. The meeting itself followed a 2-day open format, a 1-day closed expert panel meeting and two additional half day meetings to develop the Concussion Recognition Tool 5 (Pocket CRT5), Sport Concussion Assessment Tool 5 (SCAT5) and Child SCAT5. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Pilot Research Summaries, 1967-1970.

Science.gov (United States)

Casey, James L.; Hayes, Larry K.

This report contains one-page summaries of a majority of the 134 research studies funded through the Oklahoma Consortium on Research Development. The research covers the whole spectrum of academic topics , from nursing to ecology to art to politics.. Brief summaries of a majority of the 37 development seminars funded through the Consortium are…

Methodological systematic review: mortality in elderly patients with cervical spine injury: a critical appraisal of the reporting of baseline characteristics, follow-up, cause of death, and analysis of risk factors.

NARCIS (Netherlands)

Middendorp, J.J. van; Albert, T.J.; Veth, R.P.H.; Hosman, A.J.F.

2010-01-01

STUDY DESIGN: Methodologic systematic review. OBJECTIVE: To determine the validity of reported risk factors for mortality in elderly patients with cervical spine injury. SUMMARY OF BACKGROUND DATA: In elderly patients with cervical spine injury, mortality has frequently been associated with the type

International developments on implementation of Wog risk-informed inservice inspection methodology

International Nuclear Information System (INIS)

Balkey, K.R.; Bishop, B.A.; Canton, M.A.; Closky, N.B.; Haessler, R.L.; Kolonay, J.F.; Sharp, G.L.; Stevenson, P.R.

2001-01-01

The full text follows. The Westinghouse Owners Group (WOG) risk-informed inservice inspection (ISI) methodology was granted approval by the U.S. Nuclear Regulatory Commission in 1998 thereby providing an alternative to ASME Section XI Code requirements for the selection of examination locations in nuclear plant piping systems. This paper builds upon a technical paper presented at ICONE-8 that reported on the first wave of risk-informed ISI applications under development primarily focusing on those underway within the U.S. Since that time, many applications have continued within the U.S., however, much progress has been made in applying the WOG risk-informed ISI approach in several other countries. While a summary of results across the various applications will be provided, the paper will focus on the development and implementation of the WOG risk-informed ISI methodology across Europe and in Asia for both full scope and limited Class 1 scope applications. An update on future risk-informed applications, such as modifying requirements for augmented examinations for high energy line break exclusion regions and in risk-informing the safety classification of pressure boundary components in support of risk-informed regulation initiatives, will also be provided. (authors)

Recent operational history of the new Sandia Pulsed Reactor III (SPR III)

International Nuclear Information System (INIS)

Schmidt, T.R.; Estes, B.F.; Reuscher, J.A.

1977-01-01

The Sandia Pulsed Reactor III (SPR III) is a fast-pulse research reactor which was designed and built at Sandia Laboratories and achieved criticality in August 1975. The reactor is now characterized and is in an operational configuration. The core consists of 18 fuel plates (258 kg fuel mass) of fully enriched uranium alloyed with 10 wt.% molybdenum. It is arranged in an annular configuration with an inside diameter of 17.78 cm, an outside diameter of 29.72 cm, and a height of 35.9 cm. The reactor core uses reflectors of copper and aluminum for control and an external bolting arrangement to secure the fuel plates. SPR III and SPR II are operated on an interchangeable basis using the same facility and control system. As of June 1977, SPR III has had over 240 operations with core temperatures up to 541 0 C

Characterization of ribonuclease III from Brucella.

Science.gov (United States)

Wu, Chang-Xian; Xu, Xian-Jin; Zheng, Ke; Liu, Fang; Yang, Xu-Dong; Chen, Chuang-Fu; Chen, Huan-Chun; Liu, Zheng-Fei

2016-04-01

Bacterial ribonuclease III (RNase III) is a highly conserved endonuclease, which plays pivotal roles in RNA maturation and decay pathways by cleaving double-stranded structure of RNAs. Here we cloned rncS gene from the genomic DNA of Brucella melitensis, and analyzed the cleavage properties of RNase III from Brucella. We identified Brucella-encoding small RNA (sRNA) by high-throughput sequencing and northern blot, and found that sRNA of Brucella and Homo miRNA precursor (pre-miRNA) can be bound and cleaved by B.melitensis ribonuclease III (Bm-RNase III). Cleavage activity of Bm-RNase III is bivalent metal cations- and alkaline buffer-dependent. We constructed several point mutations in Bm-RNase III, whose cleavage activity indicated that the 133th Glutamic acid residue was required for catalytic activity. Western blot revealed that Bm-RNase III was differently expressed in Brucella virulence strain 027 and vaccine strain M5-90. Collectively, our data suggest that Brucella RNase III can efficiently bind and cleave stem-loop structure of small RNA, and might participate in regulation of virulence in Brucella. Copyright © 2016 Elsevier B.V. All rights reserved.

Estimating small area health-related characteristics of populations: a methodological review

Directory of Open Access Journals (Sweden)

Azizur Rahman

2017-05-01

Full Text Available Estimation of health-related characteristics at a fine local geographic level is vital for effective health promotion programmes, provision of better health services and population-specific health planning and management. Lack of a micro-dataset readily available for attributes of individuals at small areas negatively impacts the ability of local and national agencies to manage serious health issues and related risks in the community. A solution to this challenge would be to develop a method that simulates reliable small-area statistics. This paper provides a significant appraisal of the methodologies for estimating health-related characteristics of populations at geographical limited areas. Findings reveal that a range of methodologies are in use, which can be classified as three distinct set of approaches: i indirect standardisation and individual level modelling; ii multilevel statistical modelling; and iii micro-simulation modelling. Although each approach has its own strengths and weaknesses, it appears that microsimulation- based spatial models have significant robustness over the other methods and also represent a more precise means of estimating health-related population characteristics over small areas.

Advanced Fusion Concepts project summaries. FY 1983

International Nuclear Information System (INIS)

1983-06-01

This report contains descriptions of the activities of all the projects supported by the Advanced Fusion Concepts Branch of the Office of Fusion Energy, US Department of Energy. These descriptions are project summaries of each of the individual projects, and contain the following: title, principle investigators, funding levels, purpose, approach, progress, plans, milestones, graduate studients, graduates, other professional staff, and recent publications. The individual project summaries are prepared by the principle investigators in collaboration with the Advanced Fusion Concepts (AFC) Branch. In addition to the project summaries, statements of branch objectives, and budget summaries are also provided

Implications of applying methodological shortcuts to expedite systematic reviews: three case studies using systematic reviews from agri-food public health.

Science.gov (United States)

Pham, Mai T; Waddell, Lisa; Rajić, Andrijana; Sargeant, Jan M; Papadopoulos, Andrew; McEwen, Scott A

2016-12-01

The rapid review is an approach to synthesizing research evidence when a shorter timeframe is required. The implications of what is lost in terms of rigour, increased bias and accuracy when conducting a rapid review have not yet been elucidated. We assessed the potential implications of methodological shortcuts on the outcomes of three completed systematic reviews addressing agri-food public health topics. For each review, shortcuts were applied individually to assess the impact on the number of relevant studies included and whether omitted studies affected the direction, magnitude or precision of summary estimates from meta-analyses. In most instances, the shortcuts resulted in at least one relevant study being omitted from the review. The omission of studies affected 39 of 143 possible meta-analyses, of which 14 were no longer possible because of insufficient studies (studies generally resulted in less precise pooled estimates (i.e. wider confidence intervals) that did not differ in direction from the original estimate. The three case studies demonstrated the risk of missing relevant literature and its impact on summary estimates when methodological shortcuts are applied in rapid reviews. © 2016 The Authors. Research Synthesis Methods Published by John Wiley & Sons Ltd. © 2016 The Authors. Research Synthesis Methods Published by John Wiley & Sons Ltd.

Antithrombin III blood test

Science.gov (United States)

... medlineplus.gov/ency/article/003661.htm Antithrombin III blood test To use the sharing features on this page, ... a protein that helps control blood clotting. A blood test can determine the amount of AT III present ...

A post-earthquake psychopathological investigation in Armenia: methodology, summary of findings, and follow-up.

Science.gov (United States)

Khachadourian, Vahe; Armenian, Haroutune; Demirchyan, Anahit; Melkonian, Arthur; Hovanesian, Ashot

2016-07-01

The post-earthquake psychopathological investigation (PEPSI) was designed to probe the short-and long-term effects of the earthquake in northern Armenia on 7 December 1988 on survivors' mental and physical health. Four phases of this study have been conducted to date, and, overall, more than 80 per cent of a sub-sample of 1,773 drawn from an initial cohort of 32,743 was successfully followed during 2012. This paper describes the methodology employed in the evaluation, summarises previous findings, details the current objectives, and examines the general characteristics of the sample based on the most recent follow-up phase outcomes. Despite a significant decrease in psychopathology rates between 1990 and 2012, prevalence rates of post-traumatic stress disorder and depression among study participants in 2012 were greater than 15 and 26 per cent, respectively. The paper also notes the strengths and limitations of the study vis-à-vis future research and highlights the importance and potential practical implications of similar assessments and their outcomes. © 2016 The Author(s). Disasters © Overseas Development Institute, 2016.

In Vitro Optimization of Enzymes Involved in Precorrin-2 Synthesis Using Response Surface Methodology.

Science.gov (United States)

Fang, Huan; Dong, Huina; Cai, Tao; Zheng, Ping; Li, Haixing; Zhang, Dawei; Sun, Jibin

2016-01-01

In order to maximize the production of biologically-derived chemicals, kinetic analyses are first necessary for predicting the role of enzyme components and coordinating enzymes in the same reaction system. Precorrin-2 is a key precursor of cobalamin and siroheme synthesis. In this study, we sought to optimize the concentrations of several molecules involved in precorrin-2 synthesis in vitro: porphobilinogen synthase (PBGS), porphobilinogen deaminase (PBGD), uroporphyrinogen III synthase (UROS), and S-adenosyl-l-methionine-dependent urogen III methyltransferase (SUMT). Response surface methodology was applied to develop a kinetic model designed to maximize precorrin-2 productivity. The optimal molar ratios of PBGS, PBGD, UROS, and SUMT were found to be approximately 1:7:7:34, respectively. Maximum precorrin-2 production was achieved at 0.1966 ± 0.0028 μM/min, agreeing with the kinetic model's predicted value of 0.1950 μM/min. The optimal concentrations of the cofactor S-adenosyl-L-methionine (SAM) and substrate 5-aminolevulinic acid (ALA) were also determined to be 200 μM and 5 mM, respectively, in a tandem-enzyme assay. By optimizing the relative concentrations of these enzymes, we were able to minimize the effects of substrate inhibition and feedback inhibition by S-adenosylhomocysteine on SUMT and thereby increase the production of precorrin-2 by approximately five-fold. These results demonstrate the effectiveness of kinetic modeling via response surface methodology for maximizing the production of biologically-derived chemicals.

Executive summary

NARCIS (Netherlands)

van Nimwegen, N.; van Nimwegen, N.; van der Erf, R.

2009-01-01

The Demography Monitor 2008 gives a concise overview of current demographic trends and related developments in education, the labour market and retirement for the European Union and some other countries. This executive summary highlights the major findings of the Demography Monitor 2008 and further

EXECUTIVE SUMMARY OF STATE DATA RELATED TO ABANDONED CENTRALIZED AND COMMERCIAL DRILLING-FLUID DISPOSAL SITES IN LOUISIANA, NEW MEXICO, OKLAHOMA, AND TEXAS

Energy Technology Data Exchange (ETDEWEB)

H. Seay Nance

2003-03-01

This 2003 Spring Semi-Annual Report contains a summary of the Final Technical Report being prepared for the Soil Remediation Requirements at Commercial and Centralized Drilling-Fluid Disposal (CCDD) Sites project funded by the United States Department of Energy under DOE Award No. DE-AC26-99BC15225. The summary describes (1) the objectives of the investigation, (2) a rationale and methodology of the investigation, (3) sources of data, assessment of data quality, and data availability, (4) examples of well documented centralized and commercial drilling-fluid disposal (CCDD) sites and other sites where drilling fluid was disposed of, and (5) examples of abandoned sites and measures undertaken for their assessment and remediation. The report also includes most of the figures, tables, and appendices that will be included in the final report.

40 CFR 25.8 - Responsiveness summaries.

Science.gov (United States)

2010-07-01

... required.) Responsiveness summaries shall be forwarded to the appropriate decision-making official and... 25.8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL PUBLIC PARTICIPATION IN... part shall prepare a Responsiveness Summary at specific decision points as specified in program...

MIV Project: Executive Summary

DEFF Research Database (Denmark)

Ravazzotti, Mariolina T.; Jørgensen, John Leif; Neefs, Marc

1997-01-01

Under the ESA contract #11453/95/NL/JG(SC), aiming at assessing the feasibility of Rendez-vous and docking of unmanned spacecrafts, a reference mission scenario was defined. This report gives an executive summary of the achievements and results from the project.......Under the ESA contract #11453/95/NL/JG(SC), aiming at assessing the feasibility of Rendez-vous and docking of unmanned spacecrafts, a reference mission scenario was defined. This report gives an executive summary of the achievements and results from the project....

Investigation of the separation of americium(III) and europium(III) by high-speed countercurrent chromatography

International Nuclear Information System (INIS)

Wu, J.F.; Jin, Y.R.; Xu, Q.C.; Wang, S.L.; Zhang, L.X.

2005-01-01

The long-lived actinides are the important elements in the radioactive waste ;disposal. Because the ions semi diameter and chemical properties of trivalent actinides(III) and trivalent lanthanides(III) are very similar, the separation between them is very difficult. Yang Yu-Sheng put forward the actinides(III) are softer acid than the lanthanides(III), so the actinides(III) are more easily extracted by the soft extractant contain sulfur or nitrogen than the lanthanides(III). Some research have been done on the separation between actinides(III) and lanthanides(III) using the extractants contain sulfur or nitrogen. The results show that satisfactory separation efficiency was gained. Countercurrent Chromatography (CCC) have many specific advantages, such as free from solid support, permit large sample volume and high flow rate, which is useful in the preconcentration of inorganic solute and inorganic preparation. Some studies were done on the separation of lanthanides or-other inorganic elements by HSCCC, the high-purity reagents prepared by HSCCC or CPC turned out to be successful. In present paper, the investigation of separation between Americium (III) and Euricium (III) by High-Speed Countercurrent Chromatography (HSCCC) were made. The extractant used in the work was prepared by ourselves, which is of the soft extractant contrain sulfur. The effects of separation condition on the separation efficiency of Am and Eu by HSCCC were investigated using dichlorophenyl dithiophosphinic acid in xylene as the stationary phase and 0.1 mol/L NaClO4 as mobile phase, respectively. The results show that mutual separation between Am and Eu can be accomplished. The separation factor increases with the increasing of the concentration of extractant and the pH value of the mobile phase, further more, minishing the flow rate of the mobile phase can also improves the separation efficiency between Am and Eu. The nearly base separation was gained when the flow rate is 0.35 ml/min, the

Effect of pH on stability constants of Am(III)- and Cm(III)- humate complexes

International Nuclear Information System (INIS)

Samadfam, Mohammad; Jintoku, Takashi; Sato, Seichi; Ohashi, Hiroshi; Mitsugashira, Toshiaki; Hara, Mitsuo; Suzuki, Yoshimitsu

1999-01-01

The apparent stability constants of Am(III)- and Cm(III)-humate complexes were determined by dialysis method at ionic strength 0.1 in the pH range from 3.3 to 5.7 under N 2 bubbling. The Am(III) and Cm(III) loadings were about 10 -7 and 10 -10 mol/dm 3 . The concentrations of Am-241 and Cm-242 tracers were measured by α-spectrometry. It was found that the apparent stability constants were almost identical for both the Am(III)-humate and Cm(III)-humate complexes. The apparent stability constants showed a small pH-dependence, increasing from 10 4.6 at pH 3.3 to 10 5.1 at pH 5.7. The ionization of acidic functional groups of humic acid is possibly the primary factor. Above pH 6, the dialysis membrane was no langer permeable to Am(III) and Cm(III) ions and the apparent stability constant could not be experimentally obtained. The apparent stability constants between pH 6 and pH 8.5 were evaluated by considering that both binary metal-humate and ternary metal-hydroxo-humate complexes exist at pHs above 6. It was assumed that mono-hydroxo-humate complex Am(OH)HA and Cm(OH)HA are the major ternary complexes that exist below pH 9. The overall stability constants for Am(III)- and Cm(III)-humate complexes increased from 10 5.7 at pH 6 to 10 7.2 at pH 8. This implies that the formation of metal-hydroxo-humate species is preferred over the formation of hydroxide species. The apparent overall stability constants can be easily incorporated into geochemical modeling of trivalent actinide migration. The results of the present study show that the apparent stability constants determined experimentally at pH≤6 do not represent the complexation properties at higher pHs and the formation of ternary complexes should be considered in speciation calculations of radionuclides at terrestrial environment. (J.P.N.)

Articulación de fones en individuos clase esqueletal I,II y III Speech patterns in skeletal class I, II and III subjects

Directory of Open Access Journals (Sweden)

Pía Villanueva

2009-09-01

Full Text Available OBJETIVO: determinar los patrones de articulación de fones consonánticos en sujetos de habla española chilena clases I, II y III esqueletal; comparar las diferencias fonéticas que existan entre clases esqueletales. MÉTODOS: se seleccionaron 54 individuos que cumplían con los criterios de inclusión determinados mediante un examen clínico intraoral y a través del análisis de Ricketts, y se conformaron los grupos de estudio de pacientes clases esqueletales I, II y III. Se les realizó un examen fonoarticulatorio estandarizado para determinar los fones modificados y el patrón articulatorio compensatorio realizado. RESULTADOS: se observaron cambios en el punto de articulación de fones consonánticos en las tres clases esqueletales, con diferencias significativas en los grupos de fones anteriores y medios entre pacientes clases I y II, sólo en el grupo de los fones anteriores entre pacientes I y III. Entre pacientes clases II y III no se observaron diferencias significativas. Se reportan modificaciones y compensaciones cualitativamente distintas entre las clases esqueletales. CONCLUSIONES: en relación a pacientes clase I, los pacientes clase II o III, presentan distinto grado de modificación en el punto de articulación de fones consonánticos. Las diferencias observadas se relacionan con los patrones esqueletales propios de cada clase.PURPOSE: to determine the consonant phonemes articulation patterns in Chilean skeletal class I, II and III Spanish speakers and compare their phonetic differences. METHODS: fifty-four skeletal class I, II and III subjects were selected, based on intraoral clinical examination and Ricketts cephalometric analysis, constituting the study groups. A standardized phonoarticulatory test was applied to each patient to determine the modified phonemes and their compensatory patterns. RESULTS: the findings indicate changes in articulation in all three groups. Significant differences were found in anterior and medium

Methodology applied to develop the DHIE: applied methodology

CSIR Research Space (South Africa)

Herselman, Marlien

2016-12-01

Full Text Available This section will address the methodology that was applied to develop the South African Digital Health Innovation Ecosystem (DHIE). Each chapter under Section B represents a specific phase in the methodology....

Evaluation of methodology for QRA in offshore operations

International Nuclear Information System (INIS)

Vinnem, Jan Erik

1998-01-01

A brief summary is presented of the development of Quantified Risk Analysis in the offshore oil and gas industry for nearly 20 years. From a modest start in Norway as a research activity, QRA has today become one of the focal points of oil and gas management in all countries around the North Sea, and also in other areas. This was mainly initiated by authority regulations and requirements, but has now for some time been driven by the industry itself, as it sees the QRA as a vehicle to gain extended flexibility with respect to optimization of offshore safety standards. This article discusses how QRAs are used, and examines in this light how methodology developments that are and should be carried out by R and D institutions and the industry. Recommendations with respect to how and where knowledge should be developed are expressed and discussed. Lastly visions for future use and developments within the QRA technology are outlined

Summary report of the experimental fast reactor JOYO MK-III performance test

International Nuclear Information System (INIS)

Maeda, Yukimoto; Aoyama, Takafumi; Yoshida, Akihiro

2004-03-01

An upgrading project (MK-III project) was started to improve the irradiation capability of the experimental fast reactor JOYO. In this project, core replacement and increase of the reactor thermal power by the factor 1.4 were necessary for increasing the maximum fast neutron flux by the factor 1.3 and doubling the capacity for irradiation rigs. The modification of the cooling system that included the replacement of the main intermediate heat exchangers and the dump heat exchangers was completed in September 2000. After a series of system function tests, the performance test, of which objective is to fully characterize the upgraded core and heat transfer system, was started in June 2003. Twenty eight tests were selected and carried out as performance test, in order to confirm that the whole plant satisfy the design criteria and have sufficient characteristics (data necessary for safe and steady operation, core management, reactor control and monitoring) as an irradiation bed. After attaining the initial criticality of the core on 2nd July 2003, core characteristics (the excess reactivity, the isotherm temperature reactivity coefficient, the power reactivity coefficient and so on), plant characteristics (the plant heat balance, the adjustment of the temperature control system, the plant behavior at transient), shielding characteristics (dose rate distribution). As the result, it was confirmed that all the criteria regulated was satisfied and the core and plant have sufficient margins for full power operation, which was increased by the factor 1.4. Especially, nuclear analysis accuracy was verified by comparing the calculation with measured core characteristics of the initial core which consists of fifty five fresh fuel subassemblies. The operational data which is supposed to be useful for developing in-core anomaly detection system were also obtained. The operation manual and training simulator and design of next reactor development were revised based on the results

Localización empresarial en Aragón: una aplicación empírica de la ayuda a la decisión multicriterio tipo ELECTRE I y III. Robustez de los resultados obtenidos = Industrial Location Decisions in Aragon: an Empirical Application of a Multi-criterion Methodology of Aid to the Decision using ELECTRE Methods I and III. Robustness of the Obtained Results

Directory of Open Access Journals (Sweden)

García Cebrián, Lucía Isabel

2009-01-01

Full Text Available La decisión de la localización es una de las opciones estratégicas más importantes que tienen que tomar las empresas, con influencia directa sobre su competitividad. Por este motivo, se han desarrollado numerosas metodologías que ayudan en la toma de estas decisiones. En este trabajo, se realiza una aplicación empírica de una metodología de ayuda a la decisión multicriterio; específicamente, se ha optado por el método ELECTRE en sus versiones I y III, con el fin de seleccionar el mejor emplazamiento para una empresa. Para esta aplicación, se utilizan como alternativas de localización las Comarcas de Aragón, como factores de localización se utilizan 8 criterios y como peso o importancia de esos factores los obtenidos mediante una encuesta. Además, se aporta evidencia sobre la consistencia de los resultados obtenidos. Como se aprecia en el trabajo, aunque la tipología de los problemas a los que van destinados ambos métodos son distintos, los resultados obtenidos pueden ser considerados como consistentes. = The location decision is one of the most important strategic decisions that have to take the firms, with direct influence on their competitiveness. For this reason, many methodologies have been developed to help in the decision making. In this paper, we make an empirical application of a multi-criterion methodology of aid to the decision; specifically, ELECTRE method has been chosen in its versions I and III, in order to select the best place for a firm. The alternatives are counties in Aragon (Spain, and we use eight criteria. The weight has been obtained by surveys. In addition, evidence is contributed about the consistency of the obtained results. Though the typology of the problems to which both methods are destined are different, the obtained results can be considered consistent.

Current exposure method for CCP’s under Basel III

Directory of Open Access Journals (Sweden)

Antonie Kotzé

2013-04-01

Full Text Available Exposure-at-default is one of the most interesting and most difficult parameters to estimate in counterparty credit risk. Basel I offered only the non-internal Current Exposure Method for estimating this quantity whilst Basel II further introduced the Standardized Method and an Internal Model Method. Under new Basel III rules a central counterparty is defined as being a financial institution. New principles set out by the Basel Committee on Banking Supervision forces Central Counterparties in using the Current Exposure Method when estimating the credit exposures to Clearing Member banks notwithstanding its shortcomings. The Current Exposure Method relies on the Value-at-Risk methodology and its characteristics are discussed in this note. We will particularly investigate exposures to SAFCOM, the South African clearing house and point to a mathematical discrepancy on how netting is effected through the Basel accord.

CMPO-calix[4]arenes and the influence of structural modifications on the Eu(III), Am(III), Cm(III) separation

International Nuclear Information System (INIS)

Peters, C.; Braekers, D.; Desreux, J.F.; Kasyan, O.; Miroshnichenko, S.; Rudzevich, V.; Boehmer, V.

2008-01-01

The syntheses of new calix[4]arenes featuring CMPO groups on the wide rim are reported and the extraction of Am(III) and Eu(III) from concentrated HNO 3 aqueous phases are discussed with reference to the properties of the symmetric tetra-CMPO derivative 1. All extraction studies were conducted in the same experimental conditions which allows to directly compare the dependence of the distribution coefficients of various calixarenes on the acid concentration (0.1 M 3 ] < 5 M). Calix[4]arene 1 becomes a very poor extractant if the length of the aliphatic chain between the amide and phosphine oxide groups of CMPO is increased, if the bridging methylene groups are replaced by sulfur atoms or if the macrocyclic cavity size is increased. By contrast, mixed amide - CMPO calix[4]arenes are nearly as effective than 1. Moreover, Am(III)/Cm(III) separation coefficients between 1.5 and 3 have been obtained with unsymmetrical calix[4]arenes of type 1 with different aliphatic chains grafted on the narrow rim. Guidelines to anticipate the extraction ability of calix[4]arenes remain elusive because of the intricate solution behavior of these compounds. (orig.)

Key Frame Extraction in the Summary Space.

Science.gov (United States)

Li, Xuelong; Zhao, Bin; Lu, Xiaoqiang; Xuelong Li; Bin Zhao; Xiaoqiang Lu; Lu, Xiaoqiang; Li, Xuelong; Zhao, Bin

2018-06-01

Key frame extraction is an efficient way to create the video summary which helps users obtain a quick comprehension of the video content. Generally, the key frames should be representative of the video content, meanwhile, diverse to reduce the redundancy. Based on the assumption that the video data are near a subspace of a high-dimensional space, a new approach, named as key frame extraction in the summary space, is proposed for key frame extraction in this paper. The proposed approach aims to find the representative frames of the video and filter out similar frames from the representative frame set. First of all, the video data are mapped to a high-dimensional space, named as summary space. Then, a new representation is learned for each frame by analyzing the intrinsic structure of the summary space. Specifically, the learned representation can reflect the representativeness of the frame, and is utilized to select representative frames. Next, the perceptual hash algorithm is employed to measure the similarity of representative frames. As a result, the key frame set is obtained after filtering out similar frames from the representative frame set. Finally, the video summary is constructed by assigning the key frames in temporal order. Additionally, the ground truth, created by filtering out similar frames from human-created summaries, is utilized to evaluate the quality of the video summary. Compared with several traditional approaches, the experimental results on 80 videos from two datasets indicate the superior performance of our approach.

40 CFR 35.532 - Requirements summary.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Requirements summary. 35.532 Section 35.532 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE....532 Requirements summary. (a) Applicants and recipients of Performance Partnership Grants must meet...

40 CFR 35.132 - Requirements summary.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Requirements summary. 35.132 Section 35.132 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE... Requirements summary. Applicants and recipients of Performance Partnership Grants must meet: (a) The...

Global Climate Summaries

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Global Hourly Summaries are simple indicators of observational normals which include climatic data summarizations and frequency distributions. These typically...

Heterobimetallic gadolinium(III)-iron(III) complex of DTPA-bis(3-hydroxytyramide)

International Nuclear Information System (INIS)

Parac-Vogt, Tatjana N.; Kimpe, Kristof; Binnemans, Koen

2004-01-01

A derivative of diethylenetriamine-N,N,N',N'',N''-pentaacetic acid (DTPA), carrying two catechol functional groups has been synthesised by the reaction between DTPA-bis(anhydride) and 3-hydroxytyramine (dopamine). The ligand DTPA-bis(3-hydroxytyramide), [DTPA(HTA) 2 ], is able to form stable heterobimetallic complexes with gadolinium(III) and iron(III) ions. The gadolinium(III) occupies the internal coordination cage of DTPA formed by three nitrogens, two carboxylate and two amide oxygens, while the [Fe(NTA)(H 2 O) 2 ] (nitrilotriacetic acid, NTA) binds to catechol units by the substitution of two water ligands. The formation of polymeric species was avoided by using the tripodal NTA ligand. The heterobimetallic complex was characterised by means of visible absorption spectroscopy, electron spray ionisation-mass spectrometry (ESI-MS), and nuclear magnetic resonance (NMR) spectroscopy

Safeguards Summary Event List (SSEL)

International Nuclear Information System (INIS)

1983-02-01

The Safeguards Summary Event List (SSEL) provides brief summaries of several hundred safeguards-related events involving nuclear material or facilities regulated by the US Nuclear Regulatory Commission (NRC). Events are described under the categories of bomb-related, intrusion, missing and/or allegedly stolen, transportation, vandalism, arson, firearms, radiological sabotage and miscellaneous. The information contained in the event descriptions is derived primarily from official NRC reporting channels

Safeguards Summary Event List (SSEL)

International Nuclear Information System (INIS)

1982-07-01

The Safeguards Summary Event List (SSEL) provides brief summaries of several hundred safeguards-related events involving nuclear material or facilities regulated by the US Nuclear Regulatory Commission (NRC). Events are described under the categories of bomb-related, intrusion, missing and/or allegedly stolen, transportation, vandalism, arson, firearms, sabotage and miscellaneous. The information contained in the event descriptions is derived primarily from official NRC reporting channels

Separation of yttrium (III) from lanthanoids (III) by solvent extraction with substituted N-Alkylcarbonyl-N-phenylhydroxylamines

International Nuclear Information System (INIS)

Haraguchi, K.; Ogata, T.; Nakagawa, K.; Saitoh, T.; Kamidate, T.; Watanabe, H.

1996-01-01

A series of substituted N-alkylcarbonyl-N-phenylhydroxylamines(R-PHAs) were synthesized and utilized for the extraction of yttrium(III) and lanthanoids(III) in order to obtain effective extractants for the separation of yttrium(III) from the lanthanoids(III) and the mutual separation of the lanthanoids(III). The distribution ratio of yttrium(III) and the lanthanoids(III) between the carbon tetrachloride and the aqueous phases was measured as functions of the pH and the extractant concentration at 298 K at an ionic strength of 0.1 (NaNO 3 ). Yttrium(III) and the lanthanoids(III) were extracted with R-PHAs(HL) as self-adducted chelates of the form, ML 3 (HL) x , where 'x' is 1, 2 or 3 depending on the extraction system. The extractability of the metal ions decreased in the order of R-PHA having a primary, a secondary and a tertiary alkyl substituent attached to the carbonyl group because of the steric hindrance of the alkyl group. The separation factors for both Yb/Eu and Yb/Y pairs increased with increasing branching of the alkyl group of R-PHA. The excellent selectivity of R-PHAs having a tertiary alkyl group was attributable to a greater inductive effect of the tertiary alkyl group than those of the primary and secondary alkyl groups. The substituents at the phenyl group of R-PHAs gave no significant effect on the selectivity, while the extractability was enhanced considerably by introduction of electron withdrawing substituents at appropriate positions of the phenyl group of R-PHAs. (authors)

Separation by liquid-liquid extraction of actinides(III) from lanthanides(III) using new molecules: the picolinamides

International Nuclear Information System (INIS)

Cordier, P.Y.

1996-07-01

In the field of long-lived radionuclides separation from waste generated during spent fuel reprocessing, the picolinamides have been chosen as potential extractants for the selective extraction of actinides (III) from lanthanides (III). The first studies initiated on the most simple molecule of the picolinamide family, namely 2-pyridinecarboxamide, pointed out that in an aqueous media the complexation stability constant between this ligand and Am(III) is roughly 10 times higher than the ones corresponding to Ln(III). The synthesis of lipophilic derivatives of 2-pyridinecarboxamide leaded to extraction experiments. The extraction of metallic cation by lipophilic picolinamides, according to a solvatation mechanism, is strongly dependent on the nature of the amide function: a primary amide function (group I) leads to a good extraction; on the contrary, there is a decrease for secondary (group II) and tertiary (group III) amide functions. From a theoretical point of view, this work leads finally to the following conclusions: confirmation of the importance of the presence of soft donor atoms within the extractants (nitrogen in our case) for An(III)/Ln(III). Also, sensitivity of this soft donor atom regarding the protonation reaction; prevalence in our case of the affinity of the extractant for the metallic cation over the lipophilia of the extractant to ensure good distribution coefficients. The extraction and Am(III)/Ln(III) separation performances of the picolinamides from pertechnetic media leads to the design of a possible flowsheet for the reprocessing of high level liquid waste, with the new idea of an integrated technetium reflux. (author)

Research Summaries

Science.gov (United States)

Brock, Stephen E., Ed.

2010-01-01

This column features summaries of research articles from 3 recent crisis management publications. The first, "School Shootings and Counselor Leadership: Four Lessons from the Field" summarized by Kristi Fenning, was conducted as the result of the increased demand for trained crisis personnel on school campuses. Survey participants were…

Midwest Forensics Resource Center Project Summary June 2005

Energy Technology Data Exchange (ETDEWEB)

David Baldwin

2005-06-01

The mission of the MFRC Research and Development Program, is to provide technological advances in forensic science for the benefit of our regional partners as well as the forensic community at large. Key areas of forensic science need are identified through our interactions with our Midwest partners and our R&D advisory group, as well as through our participation in national meetings in forensic science. Under the sponsorship of the National Institute of Justice, the MFRC solicits proposals for the development of practical and useful technology, instrumentation, and methodology that address needs in areas related to forensic science and its application to operational crime laboratories. The MFRC facilitates proposal development by working to establish partnerships between researchers and our regional partners. The MFRC administers a peer-review of the proposals and then funds the selected projects at a cost of approximately $55,000 each, with a 12-month period of performance. The process for selection of these projects includes the following steps: (1) drafting of a call for proposals by MFRC staff, (2) review of the draft call by members of the R&D advisory committee, (3) review and approval of the call by NIJ, (4) issuance of the call to ISU, Ames Laboratory, regional partners, and research organizations, (5) receipt of proposals, (6) review of proposals by R&D advisory committee, (7) ranking and selection by MFRC staff using advisory committee reviews, with concurrence by NIJ, (8) notification of proposers, (9) receipt and review of progress reports by MFRC, (10) receipt and review of final reports by MFRC, R&D advisory committee, and NIJ. The decision to fund any specific project is based upon a peer-reviewed call-for-proposal system administered by the MFRC. The reviewers are crime laboratory specialists and scientists who are asked to rate the proposals on four criteria areas including: (1) relevance to the mission of the MFRC, (2) technical approach and

Removal of arsenic from water using manganese (III) oxide: Adsorption of As(III) and As(V).

Science.gov (United States)

Babaeivelni, Kamel; Khodadoust, Amid P

2016-01-01

Removal of arsenic from water was evaluated with manganese (III) oxide (Mn2O3) as adsorbent. Adsorption of As(III) and As(V) onto Mn2O3 was favorable according to the Langmuir and Freundlich adsorption equilibrium equations, while chemisorption of arsenic occurred according to the Dubinin-Radushkevich equation. Adsorption parameters from the Langmuir, Freundlich, and Temkin equations showed a greater adsorption and removal of As(III) than As(V) by Mn2O3. Maximum removal of As(III) and As(V) occurred at pH 3-9 and at pH 2, respectively, while removal of As(V) in the pH range of 6-9 was 93% (pH 6) to 61% (pH 9) of the maximum removal. Zeta potential measurements for Mn2O3 in As(III) was likely converted to As(V) solutions indicated that As(III) was likely converted to As(V) on the Mn2O3 surface at pH 3-9. Overall, the effective Mn2O3 sorbent rapidly removed As(III) and As(V) from water in the pH range of 6-9 for natural waters.

Annual report and summary financial statement 1990-1991

International Nuclear Information System (INIS)

1992-01-01

The 1990-1991 Annual Report for Scottish Hydro-Electric PLC includes their rotating territory in Scotland, details of the Board of Directors, the Chairman's Statement, the chief Executive's Review of Operations, a summary profit and loss account, a summary balance sheet and a summary financial statement. (UK)

Methodology for developing evidence-based clinical imaging guidelines: Joint recommendations by Korea society of radiology and national evidence-based healthcare collaborating agency

Energy Technology Data Exchange (ETDEWEB)

Choi, Sol Ji; Jo, Ae Jeong; Choi, Jin A [Div. for Healthcare Technology Assessment Research, National Evidence-Based Healthcare Collaborating Agency, Seoul (Korea, Republic of); and others

2017-01-15

This paper is a summary of the methodology including protocol used to develop evidence-based clinical imaging guidelines (CIGs) in Korea, led by the Korean Society of Radiology and the National Evidence-based Healthcare Collaborating Agency. This is the first protocol to reflect the process of developing diagnostic guidelines in Korea. The development protocol is largely divided into the following sections: set-up, process of adaptation, and finalization. The working group is composed of clinical imaging experts, and the developmental committee is composed of multidisciplinary experts to validate the methodology. The Korean CIGs will continue to develop based on this protocol, and these guidelines will act for decision supporting tools for clinicians as well as reduce medical radiation exposure.

Methodology for developing evidence-based clinical imaging guidelines: Joint recommendations by Korea society of radiology and national evidence-based healthcare collaborating agency

International Nuclear Information System (INIS)

Choi, Sol Ji; Jo, Ae Jeong; Choi, Jin A

2017-01-01

This paper is a summary of the methodology including protocol used to develop evidence-based clinical imaging guidelines (CIGs) in Korea, led by the Korean Society of Radiology and the National Evidence-based Healthcare Collaborating Agency. This is the first protocol to reflect the process of developing diagnostic guidelines in Korea. The development protocol is largely divided into the following sections: set-up, process of adaptation, and finalization. The working group is composed of clinical imaging experts, and the developmental committee is composed of multidisciplinary experts to validate the methodology. The Korean CIGs will continue to develop based on this protocol, and these guidelines will act for decision supporting tools for clinicians as well as reduce medical radiation exposure

Cancer Information Summaries

Science.gov (United States)

Peer-reviewed, evidence-based summaries on topics including adult and pediatric cancer treatment, supportive and palliative care, screening, prevention, genetics, and complementary and alternative medicine. References to published literature are included.

An investigative study towards constructing anthropocentric Man-Machine System design evaluation methodology

International Nuclear Information System (INIS)

Yoshikawa, H.; Gofuku, A.; Itoh, T.; Sasaki, K.

1992-01-01

A methodological investigation has been conducted for evaluating the reliability of man-machine interaction in the total Man-Machine System (MMS) from the view-point of safety maintenance for emergent situations of nuclear power plant. Basic considerations in our study are: (i) what are the MMS design data to be evaluated, (ii) how are those MMS design data should be treated, and (iii) how the introduction effects of various operator support tools can be evaluated. The methods of both qualitative and quantitative MMS design evaluation are summarized in this paper, with the system architecture based on man-machine interaction simulation and the related cognitive human error factor analysis. (author)

ULSGEN (Uplink Summary Generator)

Science.gov (United States)

Wang, Y.-F.; Schrock, M.; Reeve, T.; Nguyen, K.; Smith, B.

2014-01-01

Uplink is an important part of spacecraft operations. Ensuring the accuracy of uplink content is essential to mission success. Before commands are radiated to the spacecraft, the command and sequence must be reviewed and verified by various teams. In most cases, this process requires collecting the command data, reviewing the data during a command conference meeting, and providing physical signatures by designated members of various teams to signify approval of the data. If commands or sequences are disapproved for some reason, the whole process must be restarted. Recording data and decision history is important for traceability reasons. Given that many steps and people are involved in this process, an easily accessible software tool for managing the process is vital to reducing human error which could result in uplinking incorrect data to the spacecraft. An uplink summary generator called ULSGEN was developed to assist this uplink content approval process. ULSGEN generates a web-based summary of uplink file content and provides an online review process. Spacecraft operations personnel view this summary as a final check before actual radiation of the uplink data. .

Safeguards Summary Event List (SSEL)

International Nuclear Information System (INIS)

1984-03-01

The Safeguards Summary Event List (SSEL) provides brief summaries of several hundred safeguards-related events involving nuclear material or facilities regulated by the U.S. Nuclear Regulatory Commission (NRC). Events are described under the categories of bomb-related, intrusion, missing and/or allegedly stolen, transportation, tampering/vandalism, arson, firearms, radiological sabotage and miscellaneous. The information contained in the event descriptions is derived primarily from official NRC reporting channels

Carbonato-bridged Ni(II)2Ln(III)2 (Ln(III) = Gd(III), Tb(III), Dy(III)) complexes generated by atmospheric CO2 fixation and their single-molecule-magnet behavior: [(μ4-CO3)2{Ni(II)(3-MeOsaltn)(MeOH or H2O)Ln(III)(NO3)}2]·solvent [3-MeOsaltn = N,N'-bis(3-methoxy-2-oxybenzylidene)-1,3-propanediaminato].

Science.gov (United States)

Sakamoto, Soichiro; Fujinami, Takeshi; Nishi, Koshiro; Matsumoto, Naohide; Mochida, Naotaka; Ishida, Takayuki; Sunatsuki, Yukinari; Re, Nazzareno

2013-06-17

Atmospheric CO2 fixation of [Ni(II)(3-MeOsaltn)(H2O)2]·2.5H2O [3-MeOsaltn = N,N'-bis(3-methoxy-2-oxybenzylidene)-1,3-propanediaminato], Ln(III)(NO3)3·6H2O, and triethylamine occurred in methanol/acetone, giving a first series of carbonato-bridged Ni(II)2Ln(III)2 complexes [(μ4-CO3)2{Ni(II)(3-MeOsaltn)(MeOH)Ln(III)(NO3)}2] (1Gd, 1Tb, and 1Dy). When the reaction was carried out in acetonitrile/water, it gave a second series of complexes [(μ4-CO3)2{Ni(II)(3-MeOsaltn)(H2O)Ln(III)(NO3)}2]·2CH3CN·2H2O (2Gd, 2Tb, and 2Dy). For both series, each Ni(II)2Ln(III)2 structure can be described as two di-μ-phenoxo-bridged Ni(II)Ln(III) binuclear units bridged by two carbonato CO3(2-) units to form a carbonato-bridged (μ4-CO3)2{Ni(II)2Ln(III)2} structure. The high-spin Ni(II) ion has octahedral coordination geometry, and the Ln(III) ion is coordinated by O9 donor atoms from Ni(II)(3-MeOsaltn), bidentate NO3(-), and one and two oxygen atoms of two CO3(2-) ions. The NO3(-) ion for the first series roughly lie on Ln-O(methoxy) bonds and are tilted toward the outside, while for the second series, the two oxygen atoms roughly lie on one of the Ln-O(phenoxy) bonds due to the intramolecular hydrogen bond. The temperature-dependent magnetic susceptibilities indicated a ferromagnetic interaction between the Ni(II) and Ln(III) ions (Ln(III) = Gd(III), Tb(III), Dy(III)) for all of the complexes, with a distinctly different magnetic behavior between the two series in the lowest-temperature region due to the Ln(III)-Ln(III) magnetic interaction and/or different magnetic anisotropies of the Tb(III) or Dy(III) ion. Alternating-current susceptibility measurements under the 0 and 1000 Oe direct-current (dc) bias fields showed no magnetic relaxation for the Ni(II)2Gd(III)2 complexes but exhibited an out-of-phase signal for Ni(II)2Tb(III)2 and Ni(II)2Dy(III)2, indicative of slow relaxation of magnetization. The energy barriers, Δ/kB, for the spin flipping were estimated from the Arrhenius

Annual Meteorological Summaries

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Single-year summaries of observations at Weather Bureau and cooperative stations across the United States. Predominantly the single page Form 1066, which includes...

Oceanographic Monthly Summary

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Oceanographic Monthly Summary contains sea surface temperature (SST) analyses on both regional and ocean basin scales for the Atlantic, Pacific, and Indian Oceans....

AN INDUCTIVE, INTERACTIVE AND ADAPTIVE HYBRID PROBLEM-BASED LEARNING METHODOLOGY: APPLICATION TO STATISTICS

Directory of Open Access Journals (Sweden)

ADA ZHENG

2011-10-01

Full Text Available We have developed an innovative hybrid problem-based learning (PBL methodology. The methodology has the following distinctive features: i Each complex question was decomposed into a set of coherent finer subquestions by following the carefully designed criteria to maintain a delicate balance between guiding the students and inspiring them to think independently. This learning methodology enabled the students to solve the complex questions progressively in an inductive context. ii Facilitated by the utilization of our web-based learning systems, the teacher was able to interact with the students intensively and could allocate more teaching time to provide tailor-made feedback for individual student. The students were actively engaged in the learning activities, stimulated by the intensive interaction. iii The answers submitted by the students could be automatically consolidated in the report of the Moodle system in real-time. The teacher could adjust the teaching schedule and focus of the class to adapt to the learning progress of the students by analysing the automatically generated report and log files of the web-based learning system. As a result, the attendance rate of the students increased from about 50% to more than 90%, and the students’ learning motivation have been significantly enhanced.

A methodology for evaluating land suitability for medicinal plants at a regional level

Directory of Open Access Journals (Sweden)

Marco Barbaro

2011-12-01

Full Text Available Before introducing a new crop in an area, such as medicinal plant species, crop-land suitability analysis is a prerequisite to achieve an optimum exploitation of the available land resources for a sustainable agricultural production. To evaluate the land suitability it is important to take into account the habitats of the plant species. Moreover, agronomic, logistic and product quality aspects have to be considered. The importance of these aspects changes according to the stakeholders: the local government is more involved in supporting environmental suitability and production sustainability, farmers need areas which satisfy agronomic and logistic requirements, while industry is interested in the quality of production. A methodology was developed and implemented to create suitability maps for medicinal plants. Because of the generally limited information about medicinal plant adaptation, a simple methodology, based on a priori information has been developed, based on three different criteria: i environmental suitability (point of view of local government; ii agronomic, productivity and logistic suitability (point of view of the farmer; iii quality suitability (point of view of industry. For each of the three criteria, a specific macro-indicator, based on land characteristics, was calculated using membership functions. Here, a methodology to create maps for the introduction of such species was developed and implemented. This methodology can be repeated by command scripts in an easy-to-use freeware GIS. The structure of the evaluation model can be easily adapted to consider more detailed land information like climate and soil. The methodology (implemented by scripts in a freeware GIS, can be easily repeated and adapted for other situations.

Scenario development methodologies

International Nuclear Information System (INIS)

Eng, T.; Hudson, J.; Stephansson, O.

1994-11-01

In the period 1981-1994, SKB has studied several methodologies to systematize and visualize all the features, events and processes (FEPs) that can influence a repository for radioactive waste in the future. All the work performed is based on the terminology and basic findings in the joint SKI/SKB work on scenario development presented in the SKB Technical Report 89-35. The methodologies studied are a) Event tree analysis, b) Influence diagrams and c) Rock Engineering Systems (RES) matrices. Each one of the methodologies is explained in this report as well as examples of applications. One chapter is devoted to a comparison between the two most promising methodologies, namely: Influence diagrams and the RES methodology. In conclusion a combination of parts of the Influence diagram and the RES methodology is likely to be a promising approach. 26 refs

15 CFR 785.7 - Summary decision.

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Summary decision. 785.7 Section 785.7 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE ADDITIONAL PROTOCOL REGULATIONS ENFORCEMENT § 785.7 Summary...

Prof. Richard Mattessich at 95. His Research Methodology

Directory of Open Access Journals (Sweden)

Giuseppe Galassi

2017-12-01

Full Text Available This paper is presented as a tribute to prof. Richard Mattessich. It is written “through the eyes” of a researcher who has worked closely with him over a period of 42 years, starting attending his courses of “Income Determination Theory” and “Research Methodology” at the University of British Columbia in 1975. Among his huge scientific research and publications, I intend to underline these three major contributions: (i Accounting metrics and other mathematical instruments which anticipated computer spreadsheet by 30 years; (ii. The preparation of accountants for information economics by means of analytical methods; and (iii The proposition of the “onion model of reality” to distinguish different Kind of reality. Este trabajo se presenta como un tributo al profesor Richard Mattessich. Está escrito “con los ojos” de un investigador que ha trabajado estrechamente con él durante un período de 42 años, comenzando a asistir a sus cursos de " Income Determination Theory" y "Research Methodology" en la Universidad de British Columbia en 1975. Entre su investigación y publicaciones, más importantes pretendo subrayar estas tres contribuciones principales: (i Accounting metrics and other mathematical instruments which anticipated computer spreadsheet by 30 years; (ii The preparation of accountants for information economics by means of analytical methods; y (iii The proposition of the “onion model of reality” to distinguish different Kind of reality.

Complexes between lanthanide (III) and yttrium (III) picrates and tetra methylene sulfoxide as ligand

International Nuclear Information System (INIS)

Silva, M.A.A. da.

1991-01-01

The preparation and characterization of addition compounds between lanthanide (III) and yttrium (III) picrates and tetra methylene sulfoxide as ligand were described. The adducts were prepared in the molar relation 1 (salt): 3(ligand) in ethanol. They are microcrystalline with more intense color than those of their respective hydrated salts. At room temperature conditions they are non hygroscopic and do not present perceptible alterations. They became slightly opalescent, when heated between 363 and 423 K. At higher temperatures under several heating ratios, the behavior shown is the same: melting between 439 and 472 K. The characterization of the compounds was made by elemental analysis, electrolytic conductance measurements, X-ray powder patterns, infrared spectroscopy, visible electronic absorption and emission spectra of the neodymium (III) and europium (III), respectively. (author). 116 refs., 17 tabs., 11 figs

19 CFR 151.63 - Information on entry summary.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Information on entry summary. 151.63 Section 151.63 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF... Information on entry summary. Each entry summary covering wool or hair subject to duty at a rate per clean...

Interoperability Assets for Patient Summary Components: A Gap Analysis.

Science.gov (United States)

Heitmann, Kai U; Cangioli, Giorgio; Melgara, Marcello; Chronaki, Catherine

2018-01-01

The International Patient Summary (IPS) standards aim to define the specifications for a minimal and non-exhaustive Patient Summary, which is specialty-agnostic and condition-independent, but still clinically relevant. Meanwhile, health systems are developing and implementing their own variation of a patient summary while, the eHealth Digital Services Infrastructure (eHDSI) initiative is deploying patient summary services across countries in the Europe. In the spirit of co-creation, flexible governance, and continuous alignment advocated by eStandards, the Trillum-II initiative promotes adoption of the patient summary by engaging standards organizations, and interoperability practitioners in a community of practice for digital health to share best practices, tools, data, specifications, and experiences. This paper compares operational aspects of patient summaries in 14 case studies in Europe, the United States, and across the world, focusing on how patient summary components are used in practice, to promote alignment and joint understanding that will improve quality of standards and lower costs of interoperability.

A literature review of applied adaptive design methodology within the field of oncology in randomised controlled trials and a proposed extension to the CONSORT guidelines.

Science.gov (United States)

Mistry, Pankaj; Dunn, Janet A; Marshall, Andrea

2017-07-18

The application of adaptive design methodology within a clinical trial setting is becoming increasingly popular. However the application of these methods within trials is not being reported as adaptive designs hence making it more difficult to capture the emerging use of these designs. Within this review, we aim to understand how adaptive design methodology is being reported, whether these methods are explicitly stated as an 'adaptive design' or if it has to be inferred and to identify whether these methods are applied prospectively or concurrently. Three databases; Embase, Ovid and PubMed were chosen to conduct the literature search. The inclusion criteria for the review were phase II, phase III and phase II/III randomised controlled trials within the field of Oncology that published trial results in 2015. A variety of search terms related to adaptive designs were used. A total of 734 results were identified, after screening 54 were eligible. Adaptive designs were more commonly applied in phase III confirmatory trials. The majority of the papers performed an interim analysis, which included some sort of stopping criteria. Additionally only two papers explicitly stated the term 'adaptive design' and therefore for most of the papers, it had to be inferred that adaptive methods was applied. Sixty-five applications of adaptive design methods were applied, from which the most common method was an adaptation using group sequential methods. This review indicated that the reporting of adaptive design methodology within clinical trials needs improving. The proposed extension to the current CONSORT 2010 guidelines could help capture adaptive design methods. Furthermore provide an essential aid to those involved with clinical trials.

DSM-III-R and religion.

Science.gov (United States)

Post, S G

1992-07-01

The interpretation of religion in DSM-III-R contains considerable negative bias and contributes to unfair stereotypes of religious persons. Particularly new religious movements and religious conversion are unfairly interpreted under the DSM-III-R heading, 'Dissociative Disorder Not Otherwise Specified'. It is suggested that a more balanced and respectful interpretation of religion is needed in DSM-III-R, since psychiatry through its official nomenclature should not contribute to social intolerance of religious nonconformity.

29 CFR 18.40 - Motion for summary decision.

Science.gov (United States)

2010-07-01

... OFFICE OF ADMINISTRATIVE LAW JUDGES General § 18.40 Motion for summary decision. (a) Any party may, at... that a party is entitled to summary decision. The administrative law judge may deny the motion whenever... 29 Labor 1 2010-07-01 2010-07-01 true Motion for summary decision. 18.40 Section 18.40 Labor...

Surgical discharge summaries: improving the record.

Science.gov (United States)

Adams, D C; Bristol, J B; Poskitt, K R

1993-03-01

The problem area of communication between hospital and general practitioners may potentially be improved by the advent of new information technology. The introduction of a regional computer database for general surgery allows the rapid automated production of discharge summaries and has provided us with the opportunity for auditing the quality of old and new styles of discharge communication. A total of 118 general practitioners were sent a postal questionnaire to establish their views on the relative importance of various aspects of patient information and management after discharge. A high response rate (97%) indicated the interest of general practitioners in this topic. The majority (73%) believed that summaries should be delayed no more than 3 days. The structured and shortened new format was preferred to the older style of discharge summary. The older format rarely arrived within an appropriate time and its content was often felt to be either inadequate (35%) or excessive (7%) compared with the new format (8% and 1%, respectively). The diagnosis, information given to the patient, clinic date, list of medications and investigations were considered the more important details in the summary. Improvements in the discharge information were suggested and have subsequently been incorporated in our discharge policy. The use of new information technology, intended to facilitate clinical audit, has improved our ability to generate prompt, well-structured discharge summaries which are accepted by the general practitioners.

Sb(III) and Sb(V) separation and analytical speciation by a continuous tandem on-line separation device in connection with inductively coupled plasma atomic emission spectrometry

Energy Technology Data Exchange (ETDEWEB)

Menendez Garcia, A. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.; Perez Rodriguez, M.C. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.; Sanchez Uria, J.F. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.; Sanz-Medel, A. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.

1995-09-01

A sensitive, precise and automated non-chromatographic method for Sb(III) and Sb(V) analytical speciation based on a continuous tandem on-line separation device in connection with inductively coupled plasma-atomic emission (ICP-AES) detection is proposed. Two on-line successive separation steps are included into this method: a continuous liquid-liquid extraction of Sb(III) with ammonium pyrrolidine dithiocarbamate (APDC) into methylisobuthylketone (MIBK), followed by direct stibine generation from the organic phase. Both separation steps are carried out in a continuous mode and on-line with the ICP-AES detector. Optimization of experimental conditions for the tandem separation and ICP-AES detection are investigated in detail. Detection limits for Sb(III) were 3 ng.mL{sup -1} and for Sb(V) 8 ng.mL{sup -1}. Precisions observed are in the range {+-} 5%. The proposed methodology has been applied to Sb(III) and Sb(V) speciation in sea-water samples. (orig.)

The capacity limitations of orientation summary statistics

Science.gov (United States)

Attarha, Mouna; Moore, Cathleen M.

2015-01-01

The simultaneous–sequential method was used to test the processing capacity of establishing mean orientation summaries. Four clusters of oriented Gabor patches were presented in the peripheral visual field. One of the clusters had a mean orientation that was tilted either left or right while the mean orientations of the other three clusters were roughly vertical. All four clusters were presented at the same time in the simultaneous condition whereas the clusters appeared in temporal subsets of two in the sequential condition. Performance was lower when the means of all four clusters had to be processed concurrently than when only two had to be processed in the same amount of time. The advantage for establishing fewer summaries at a given time indicates that the processing of mean orientation engages limited-capacity processes (Experiment 1). This limitation cannot be attributed to crowding, low target-distractor discriminability, or a limited-capacity comparison process (Experiments 2 and 3). In contrast to the limitations of establishing multiple summary representations, establishing a single summary representation unfolds without interference (Experiment 4). When interpreted in the context of recent work on the capacity of summary statistics, these findings encourage reevaluation of the view that early visual perception consists of summary statistic representations that unfold independently across multiple areas of the visual field. PMID:25810160

Worldwide Airfield Summary

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Worldwide Airfield Summary contains a selection of climatological data produced by the U.S. Air Force, Air Weather Service. The reports were compiled from dozens...

Executive summary

International Nuclear Information System (INIS)

2002-01-01

On 18 May 2001, the Finnish Parliament ratified the Decision in Principle on the final disposal facility for spent nuclear fuel at Olkiluoto, within the municipality of Eurajoki. The Municipality Council and the government has made positive decisions earlier, at the end of 2000, and in compliance with the Nuclear Energy Act, Parliament's ratification was then required. The decision is valid for the spent fuel generated by the existing Finnish nuclear power plants and means that the construction of the final disposal facility is considered to be in line with the overall good of society. Earlier steps included, amongst others, the approval of the technical project by the Safety Authority. Future steps include construction of an underground rock characterisation facility, ONKALO (2003-2004), and application for separate construction and operating licences for the final disposal facility (from about 2010). How did this political and societal decision come about? The FSC Workshop provided the opportunity to present the history leading up to the Decision in Principle (DiP), and to examine future perspectives with an emphasis on stakeholder involvement. This Executive Summary gives an overview of the presentations and discussions that took place at the workshop. It presents, for the most part, a factual account of the individual presentations and of the discussions that took place. It relies importantly on the notes that were taken at the meeting. Most materials are elaborated upon in a fuller way in the texts that the various speakers and session moderators contributed for these proceedings. The structure of the Executive Summary follows the structure of the workshop itself. Complementary to this Summary and also provided with this document, is a NEA Secretariat's perspective aiming to place the results of all discussions, feedback and site visit into an international perspective. (authors)

Task III: UCSD/DIII-D/Textor FY-97-98 Accomplishments

International Nuclear Information System (INIS)

Boedo, J.A.

2000-01-01

OAK (B204) Task III: UCSD/DIII-D/Textor FY-97-98 Accomplishments. A comprehensive report on the physics of pump limiters and particularly, the characterization of ALT-II, was published in Nuclear Fusion, bringing the project to a closure. The performance of the toroidal pump limiter was characterized under full auxiliary heating of 7 MW of NBI and ICRH and full pumping, as stated in the project milestones. Relevant highlights are: (1) Pumping with ALT-II allows for density control. (2) The achieved exhaust efficiency is 4% during NBI operation and near 2% during OH or ICRH operation. (3) We have shown that an exhaust efficiency of 2% is sufficient to satisfy the ash removal requirements of fusion reactors. (4) The plasma particle efflux and the pumped flux both increase with density and heating power. (5) The particle confinement time is less than the energy confinement time by a factor of 4. In summary, pumped belt limiters could provide the density control and ash exhaust requirements of fusion reactors

Archetype modeling methodology.

Science.gov (United States)

Moner, David; Maldonado, José Alberto; Robles, Montserrat

2018-03-01

Clinical Information Models (CIMs) expressed as archetypes play an essential role in the design and development of current Electronic Health Record (EHR) information structures. Although there exist many experiences about using archetypes in the literature, a comprehensive and formal methodology for archetype modeling does not exist. Having a modeling methodology is essential to develop quality archetypes, in order to guide the development of EHR systems and to allow the semantic interoperability of health data. In this work, an archetype modeling methodology is proposed. This paper describes its phases, the inputs and outputs of each phase, and the involved participants and tools. It also includes the description of the possible strategies to organize the modeling process. The proposed methodology is inspired by existing best practices of CIMs, software and ontology development. The methodology has been applied and evaluated in regional and national EHR projects. The application of the methodology provided useful feedback and improvements, and confirmed its advantages. The conclusion of this work is that having a formal methodology for archetype development facilitates the definition and adoption of interoperable archetypes, improves their quality, and facilitates their reuse among different information systems and EHR projects. Moreover, the proposed methodology can be also a reference for CIMs development using any other formalism. Copyright © 2018 Elsevier Inc. All rights reserved.

The Ideal Hospital Discharge Summary: A Survey of U.S. Physicians.

Science.gov (United States)

Sorita, Atsushi; Robelia, Paul M; Kattel, Sharma B; McCoy, Christopher P; Keller, Allan Scott; Almasri, Jehad; Murad, Mohammad Hassan; Newman, James S; Kashiwagi, Deanne T

2017-09-06

Hospital discharge summaries enable communication between inpatient and outpatient physicians. Despite existing guidelines for discharge summaries, they are frequently suboptimal. The aim of this study was to assess physicians' perspectives about discharge summaries and the differences between summaries' authors (hospitalists) and readers (primary care physicians [PCPs]). A national survey of 1600 U.S. physicians was undertaken. Primary measures included physicians' preferences in discharge summary standardization, content, format, and audience. A total of 815 physicians responded (response rate = 51%). Eighty-nine percent agreed that discharge summaries "should have a standardized format." Most agreed that summaries should "document everything that was done, found, and recommended in the hospital" (64%) yet "only include details that are highly pertinent to the hospitalization" (66%). Although 74% perceived patients as an important audience of discharge summaries, only 43% agreed that summaries "should be written in language that patients…can easily understand," and 68% agreed that it "should be written solely for provider-to-provider communication." Compared with hospitalists, PCPs preferred comprehensive summaries (68% versus 59%, P = 0.002). More PCPs agreed that separate summaries should be created for patients and for provider-to-provider communication than hospitalists (60% versus 47%, P summary" (44% versus 23%, P summary" (60% versus 38%, P summaries should have a standardized format but do not agree on how comprehensive or in what format they should be. Efforts are necessary to build consensus toward the ideal discharge summary.

Distal biceps brachii tendon repair: a systematic review of patient outcome determination using modified Coleman methodology score criteria.

Science.gov (United States)

Nyland, John; Causey, Brandon; Wera, Jeff; Krupp, Ryan; Tate, David; Gupta, Amit

2017-07-01

This systematic literature review evaluated the methodological research design quality of studies that evaluated patient outcomes following distal biceps brachii tendon repair and developed evidence-based recommendations for future patient clinical outcomes research. Following the preferred reporting items for systematic reviews and meta-analyses criteria, and using "biceps brachii", "tendon", "repair" and "outcome assessment" search terms, the CINAHL, Academic Search Premier and MEDLINE databases were searched from January 1960-October 2015. The modified Coleman methodology score (MCMS) served as the primary outcome measure. Descriptive statistical analysis was performed for composite and component MCMS and for patient outcome assessment methodology use frequency. A total of 93 studies were evaluated. Overall MCMS was low (57.1 ± 14). Only 12 (12.9 %) had prospective cohort or randomized controlled trial designs. There was a moderate relationship between publication year and MCMS (r = 0.53, P research study methodological scores improved on average since 2008, generally low MCMS scores, retrospective designs, lack of eccentric elbow flexor or supinator strength testing, and poorly described surgical and rehabilitation descriptions remain commonplace. These findings decrease clinical study validity and generalizability. III.

15 CFR 904.505 - Summary sale.

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Summary sale. 904.505 Section 904.505 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) NATIONAL OCEANIC... and Forfeiture Procedures § 904.505 Summary sale. (a) In view of the perishable nature of fish, any...

Determination of Cu(III) and Cu(II)+Cu(III) in superconducting copper ceramics

International Nuclear Information System (INIS)

Nedelcheva, T.; Kostadinova, L.; Stoyanova-Ivanova, A.; Ivanova, I.

1992-01-01

Copper(III) and total copper in superconducting Y-Ba-Cu oxide and related compounds can be determinated by two successive iodimetric titrations after the sample has been dissolved under Ar in HCl/KI medium. First, the iodine equivalent to copper(III) is titrated with Na 2 S 2 O 3 solution at pH 4.8, copper(II) being masked with EDTA. The total copper is then determined in the same solution by demasking with acid and iodide, followed by iodimetric titration. The method is both accurate and reproducible. The relative standard deviations for 1.074% copper(III) and 23.37% total copper are 0.8% and 0.3%, respectively. (orig.)

Annual report and summary financial statement 1991-1992

International Nuclear Information System (INIS)

1993-01-01

The 1991-92 Annual Report for Scottish Hydro-Electric PLC is presented. It includes key financial statistics, the financial calendar, details of the Board of Directors, the Chairman's Statement, the Chief Executives' review of operations, operational statistics, a summary financial statement, a summary group profit and loss account, summary balance sheets, the Auditors' Report and a customer map. (UK)

Speciation of Am(III)/Eu(III) sorbed on γ-alumina. Effect of metal ion concentration

International Nuclear Information System (INIS)

Kumar, S.; Tomar, B.S.; Godbole, S.V.

2013-01-01

The present paper describes the speciation of Am(III)/Eu(III) sorbed on γ-alumina, and its evolution with changing metal ion concentration, studied using batch sorption experiment, time resolved fluorescence spectroscopy (TRFS), extended X-ray absorption fine structure (EXAFS) and surface Complexation modeling (SCM). Though numerous studies exist in the literature on the speciation of trivalent actinides and lanthanides on alumina surface, the mechanism of sorption at high metal ion concentrations is not yet fully understood. Batch sorption experiments of Am(III) on γ-alumina under varying condition of pH (3-10), ionic strength (0.005-0.1 M NaClO 4 ) and metal ion concentration (10 -7 -10 -4 M) were performed. Higher metal ion concentration was achieved by the addition of Eu(III) considering it as an analogue of Am(III). Time resolved fluorescence spectroscopy (TRFS) study of Eu(III) sorbed on γ-alumina at the metal ion concentration of 5.0 x 10 -5 M was carried out over pH 4 to 7. TRFS showed the presence of two surface species, with distinctly different fluorescence decay life times. The shorter lifetime value and its changing pattern with pH indicate the surface species corresponding to this component to be monodentate species > AlOAm 2+ and its hydrolyzed forms. The sorbed Eu 3+ species corresponding to the longer lifetime value has 2-3 water molecules in its first coordination sphere and is multidentate in its binding on alumina surface. Extended X-ray absorption fine structure (EXAFS) measurement of Eu:γ-Al 2 O 3 sorption systems at pH 6.18 and 7.15 corroborate the existence of two surface complexes. Further it suggests the edge sharing bidentate binding of Eu on AlO 6 octahedra as the co-ordination mode of the higher lifetime component. Surface Complexation Modeling (SCM) of Am(III)/Eu(III) sorption onto γ-alumina at pH ≤7 has been carried out using these two surface species. 2-pK surface complexation modeling coupled with constant capacitance model

Assessing the comparative effectiveness of newly marketed medications: methodological challenges and implications for drug development.

Science.gov (United States)

Schneeweiss, S; Gagne, J J; Glynn, R J; Ruhl, M; Rassen, J A

2011-12-01

Comparative-effectiveness research (CER) aims to produce actionable evidence regarding the effectiveness and safety of medical products and interventions as they are used outside of controlled research settings. Although CER evidence regarding medications is particularly needed shortly after market approval, key methodological challenges include (i) potential bias due to channeling of patients to the newly marketed medication because of various patient-, physician-, and system-related factors; (ii) rapid changes in the characteristics of the user population during the early phase of marketing; and (iii) lack of timely data and the often small number of users in the first few months of marketing. We propose a mix of approaches to generate comparative-effectiveness data in the early marketing period, including sequential cohort monitoring with secondary health-care data and propensity score (PS) balancing, as well as extended follow-up of phase III and phase IV trials, indirect comparisons of placebo-controlled trials, and modeling and simulation of virtual trials.

The PISC programme on defective steam generator tubes inspection summary report

International Nuclear Information System (INIS)

Birac, C.; Comby, R.; Maciga, G.; Zanella, G.; Perez Prat, J.; Estorff, U. von

1995-01-01

The PISC III Actions are intended to extend the results and methodologies of the previous PISC exercises, i.e. the validation of the capabilities of the various examination techniques when used on real defects in real components under realistic conditions of inspection. The objective of this action is relatively close to that of the heavy structures programmes: the experimental evaluation of the performance of test procedures used for steam generator tubes in nuclear power plants during in-service or pre-service inspections. The exercise is a capability exercise consisting of Round Robin Tests on individual tubes including calibration, training and blind test tubes. In this paper the main conclusions from the RRT conducted in the framework of Action 5 will be presented and discussed. (author). 7 refs, 4 figs, 2 tabs

Efficient preliminary floating offshore wind turbine design and testing methodologies and application to a concrete spar design.

Science.gov (United States)

Matha, Denis; Sandner, Frank; Molins, Climent; Campos, Alexis; Cheng, Po Wen

2015-02-28

The current key challenge in the floating offshore wind turbine industry and research is on designing economic floating systems that can compete with fixed-bottom offshore turbines in terms of levelized cost of energy. The preliminary platform design, as well as early experimental design assessments, are critical elements in the overall design process. In this contribution, a brief review of current floating offshore wind turbine platform pre-design and scaled testing methodologies is provided, with a focus on their ability to accommodate the coupled dynamic behaviour of floating offshore wind systems. The exemplary design and testing methodology for a monolithic concrete spar platform as performed within the European KIC AFOSP project is presented. Results from the experimental tests compared to numerical simulations are presented and analysed and show very good agreement for relevant basic dynamic platform properties. Extreme and fatigue loads and cost analysis of the AFOSP system confirm the viability of the presented design process. In summary, the exemplary application of the reduced design and testing methodology for AFOSP confirms that it represents a viable procedure during pre-design of floating offshore wind turbine platforms. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Organometallic neptunium(III) complexes.

Science.gov (United States)

Dutkiewicz, Michał S; Farnaby, Joy H; Apostolidis, Christos; Colineau, Eric; Walter, Olaf; Magnani, Nicola; Gardiner, Michael G; Love, Jason B; Kaltsoyannis, Nikolas; Caciuffo, Roberto; Arnold, Polly L

2016-08-01

Studies of transuranic organometallic complexes provide a particularly valuable insight into covalent contributions to the metal-ligand bonding, in which the subtle differences between the transuranium actinide ions and their lighter lanthanide counterparts are of fundamental importance for the effective remediation of nuclear waste. Unlike the organometallic chemistry of uranium, which has focused strongly on U(III) and has seen some spectacular advances, that of the transuranics is significantly technically more challenging and has remained dormant. In the case of neptunium, it is limited mainly to Np(IV). Here we report the synthesis of three new Np(III) organometallic compounds and the characterization of their molecular and electronic structures. These studies suggest that Np(III) complexes could act as single-molecule magnets, and that the lower oxidation state of Np(II) is chemically accessible. In comparison with lanthanide analogues, significant d- and f-electron contributions to key Np(III) orbitals are observed, which shows that fundamental neptunium organometallic chemistry can provide new insights into the behaviour of f-elements.

Electron-Cloud Build-Up: Summary

International Nuclear Information System (INIS)

Furman, M.A.

2007-01-01

I present a summary of topics relevant to the electron-cloud build-up and dissipation that were presented at the International Workshop on Electron-Cloud Effects 'ECLOUD 07' (Daegu, S. Korea, April 9-12, 2007). This summary is not meant to be a comprehensive review of the talks. Rather, I focus on those developments that I found, in my personal opinion, especially interesting. The contributions, all excellent, are posted in http://chep.knu.ac.kr/ecloud07/

Conference summaries

International Nuclear Information System (INIS)

1986-01-01

This volume contains conference summaries of the international conference on radioactive waste management of the Canadian Nuclear Society. Topics of discussion include: storage and disposal; hydrogeology and geochemistry; transportation; buffers and backfill; public attitudes; tailings; site investigations and geomechanics; concrete; economics; licensing; matrix materials and container design; durability of fuel; biosphere modelling; radioactive waste processing; and, future options

Diglycolic acid modified zirconium phosphate and studies on the extraction of Am(III) and Eu(III) from dilute nitric acid medium

Energy Technology Data Exchange (ETDEWEB)

Selvan, B. Robert; Suneesh, A.S.; Venkatesan, K.A.; Antony, M.P. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Fuel Chemistry Division; Dasthaiah, K.; Gardas, R.L. [Indian Institute of Technology - Madras, Chennai (India). Dept. of Chemistry

2017-06-01

Diglycolic acid modified zirconium phosphate (ZrP-DGA) was prepared and studied for the extraction of Am(III) and Eu(III) from dilute nitric acid medium. The distribution coefficient (K{sub d}, mL.g{sup -1}) of Am(III) and Eu(III) was measured as a function of time, pH and concentration of Eu(III) ion etc. The K{sub d} of Am(III) and Eu(III) increased with increase of pH, reached a maximum value of distribution coefficient at pH 1.5 - 2, followed by decrease in K{sub d} values. Rapid extraction of Am(III) and Eu(III) in ZrP-DGA was observed followed by the establishment of equilibrium occurred in 100 min. Kinetics of extraction was fitted in to pseudo second order rate equation. The amount of Eu(III) loaded in ZrP-DGA increased with increase in the concentration of Eu(III) ion in aqueous phase and the isotherm was fitted in to Langmuir and Freundlich adsorption models. The extraction of Am(III) in ZrP-DGA was higher as compared to Eu(III) and the interference of Eu(III) on the extraction of Am(III) was studied. The distribution coefficient of some lanthanides in ZrP-DGA was measured and the K{sub d} of lanthanides increased across the lanthanide series. The extracted trivalent metal ions were recovered in three contacts of loaded ZrP-DGA with 0.5 M nitric acid.

Summaries of FY 1997 engineering research

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

This report documents the Basic Energy Sciences (BES) Engineering Research Program for fiscal year 1997, it provides a summary for each of the program projects in addition to a brief program overview. The report is intended to provide staff of Congressional committees, other executive departments, and other DOE offices with substantive program information so as to facilitate governmental overview and coordination of Federal research programs. Of equal importance, its availability facilitates communication of program information to interested research engineers and scientists. The individual project summaries follow the program overview. The summaries are ordered alphabetically by name of institution; the table of contents lists all the institutions at which projects were sponsored in fiscal year 1997. Each project entry begins with an institutional-departmental heading. The names of investigators are listed immediately below the title. The funding level for fiscal year 1997 appears to the right of address. The summary description of the project completes the entry. A separate index of Principal Investigators includes phone number, fax number and e-main address, where available.

FAIR - Baseline technical report. Executive summary

International Nuclear Information System (INIS)

Gutbrod, H.H.; Augustin, I.; Eickhoff, H.; Gross, K.D.; Henning, W.F.; Kraemer, D.; Walter, G.

2006-09-01

This document presents the Executive Summary, the first of six volumes comprising the 2006 Baseline Technical Report (BTR) for the international FAIR project (Facility for Antiproton and Ion Research). The BTR provides the technical description, cost, schedule, and assessments of risk for the proposed new facility. The purpose of the BTR is to provide a reliable basis for the construction, commissioning and operation of FAIR. The BTR is one of the central documents requested by the FAIR International Steering Committee (ISC) and its working groups, in order to prepare the legal process and the decisions on the construction and operation of FAIR in an international framework. It provides the technical basis for legal contracts on contributions to be made by, so far, 13 countries within the international FAIR Consortium. The BTR begins with this extended Executive Summary as Volume 1, which is also intended for use as a stand-alone document. The Executive Summary provides brief summaries of the accelerator facilities, the scientific programs and experimental stations, civil construction and safety, and of the workproject structure, costs and schedule. (orig.)

The Pseudomonas syringae type III effector HopG1 targets mitochondria, alters plant development, and suppresses plant innate immunity

Science.gov (United States)

Block, Anna; Guo, Ming; Li, Guangyong; Elowsky, Christian; Clemente, Thomas E.; Alfano, James R.

2009-01-01

Summary The bacterial plant pathogen Pseudomonas syringae uses a type III protein secretion system to inject type III effectors into plant cells. Primary targets of these effectors appear to be effector-triggered immunity (ETI) and pathogen-associated molecular pattern (PAMP)-triggered immunity (PTI). The type III effector HopG1 is a suppressor of ETI that is broadly conserved in bacterial plant pathogens. Here we show that HopG1 from P. syringae pv. tomato DC3000 also suppresses PTI. Interestingly, HopG1 localizes to plant mitochondria, suggesting that its suppression of innate immunity may be linked to a perturbation of mitochondrial function. While HopG1 possesses no obvious mitochondrial signal peptide, its N-terminal two-thirds was sufficient for mitochondrial localization. A HopG1-GFP fusion lacking HopG1’s N-terminal 13 amino acids was not localized to the mitochondria reflecting the importance of the N-terminus for targeting. Constitutive expression of HopG1 in Arabidopsis thaliana, Nicotiana tabacum (tobacco) and Lycopersicon esculentum (tomato) dramatically alters plant development resulting in dwarfism, increased branching and infertility. Constitutive expression of HopG1 in planta leads to reduced respiration rates and an increased basal level of reactive oxygen species. These findings suggest that HopG1’s target is mitochondrial and that effector/target interaction promotes disease by disrupting mitochondrial functions. PMID:19863557

SI:FatiguePro 4 Advanced Approach for Fatigue Monitoring

International Nuclear Information System (INIS)

Evon, Keith; Gilman, Tim; Carney, Curt

2012-01-01

Many nuclear plants are making commitments to implement fatigue monitoring systems in support of license renewal. Current fatigue monitoring systems use the methodology of ASME Code Subarticle NB-3200, which is a design code intended to compute a bounding cumulative usage factor (CUF). The first generation of fatigue monitoring software utilized a simplified, single stress term assumption and classical stress cycle-counting methods that take order into account such as Rainflow or Ordered Overall Range counting. Recently, the NRC has indicated in Regulatory Issue Summary 2008-30 that any fatigue analyses in support of License Renewal should use ASME Code Section III methodologies considering all six stress components. In addition, fatigue calculations for the license renewal term are required to consider the effects of environment. The implementation of a six stress term NB-3200 fatigue calculation to a Boiling Water Reactor (BWR) feedwater nozzle, including environmental effects, is the topic of this paper. Differences in results between the advanced methodology and the simplified methodology are discussed. (author)

Sociological impacts of nuclear generating stations - summary report on the NRC post-licensing studies. Final report 1 Oct 78-4 Jan 82

International Nuclear Information System (INIS)

Chalmers, J.; Pijawka, D.; Branch, K.; Bergmann, P.; Flynn, J.

1982-07-01

The Post-Licensing Studies had four objectives. The first was to identify the socioeconomic effects resulting from the construction and operation of each of twelve nuclear power stations. The socioeconomic variables examined included: economic, demographic, housing, government, public response, and social organization characteristics. The second objective was to determine the way in which the identified effects were evaluated by study area groups. The third objective was to identify the determinants of the project-related effects. This task required knowledge of what combination of site, project, or other determinants was responsible for the project-related effects and for the evaluation of the effects. The fourth objective was to make recommendations with respect to assessment methodologies that could best be used to project the socioeconomic effects of the construction and operation of proposed nuclear generating stations. The objectives of the Post-Licensing Studies are met by the twelve individual case studies and by the Summary Report. The case studies identified the nuclear power stations and describe the evaluation of the effects by area residents. The Summary Report describes the collective findings of the individual case studies, compares the findings across sites to identify possible determinants of the effects, and examines the implication of the findings for future siting decisions and for the methodology most appropriate for projective assessments

Photocatalytic Pre-Oxidation of Arsenic (III) in Groundwater by a Visible-Light-Driven System with Magnetic Separating Characteristic

Science.gov (United States)

Cui, Y.; Liu, Y.; Peng, L.; Qin, Y.

2017-12-01

Arsenic was a typical toxic metalloid element and its contamination in groundwater was widely recognized as a global health problem, especially in north China, where people depended on groundwater as water resource. Arsenic was existed as As(III) in underground water, and has low affinity to the surface of various minerals and more toxic and more difficultly to be removed compared with As(V), so a pre-oxidation technology by transforming As (III) to As (V) is highly desirable. Electrochemical and oxidizing agents were traditional technology, which usually causes secondary pollution. A novel methodology is presented here, using prepared magnetic visible-light-driven nanomaterials as recyclable media to investigate As(III) pre-oxidation processing. Ag@AgCl core-shell nanowires were first synthesized by oxidation of Ag nanowires with moderate FeCl3, and exhibited excellent photocatalytic activity to As(III) with visible-light. The ratio of chloridization was proved to act as key effect on photocatalytic oxidation efficiency. Testing with simulated groundwater condition proved that pH, ionic strength and concentration of humic acid have obvious effects on Ag@AgCl photocatalytic ability. h+ and ·O2- were confirmed to be the main active species during the visible-light driven photocatalytic oxidation process for As(III) by trapping experiments with radical scavengers. Then Fe0 was introduced to prepare Fe-Ag nanowire and chloridized into Fe-Ag@AgCl to provide magnetic characteristic. The magnetic recycling and re-chloride experiments validated this visible-light-driven material has excellent stable and high reused ability as photocatalyst under visible light irradiation.

Qualitative Features of Written Summary Texts Produced by Teachers

Directory of Open Access Journals (Sweden)

Hülya YAZICI OKUYAN

2011-12-01

Full Text Available This research aimed to find an answer to the question: "Do summary texts produced by teachers have the characteristics that a summary text is supposed to have?” Descriptive method was used in the research. The study group consisted of 55 teachers who work as Turkish Language and Literature teachers at central primary and secondary schools in Burdur. During the research, the essay “Kitap Az Yaşamayı Önler” by Çetin Altan was used as the source text and the summary texts produced by teachers were evaluated using a criteria-based and gradual analysis instrument. At the end of the study, it was determined that the teachers only managed to reach the sufficient level in terms of reconstructing the summary texts through authentic sentences and reflecting the main idea of the source text in the summary texts. However, according to the research results regarding the teachers’ competence in creating a new title for the summary texts, including the source text’s all supporting ideas and important information in the summary texts and providing the summary texts with the capacity of reflecting the source text, it has been observed that the teachers lack the required knowledge and skill

Summary of the ECLOUD'04 Workshop

International Nuclear Information System (INIS)

Macek, R.; Furman, M.

2004-01-01

The 31st ICFA Advanced Beam Dynamics Workshop on Electron-Cloud Effects ''ECLOUD'04'' was held April 19-23, 2004 at Napa, CA, USA. A broad range of current topics in this field were illuminated by 53 talks in 7 sessions plus 6 session summaries at the final summary session. These covered a variety of experimental methods and results, along with progress on understanding of the topic obtained from simulations and analytic theory, and evaluations of the effectiveness of various methods/mechanisms for mitigation of the adverse impact on accelerator performance. In addition, a panel discussion was held on ''Future Needs and Future Directions''. A summary of progress on the major themes covered at ECLOUD'04 is presented

Belgian Workshop (November 2003) - Executive Summary and International Perspective

International Nuclear Information System (INIS)

2004-01-01

The fourth workshop of the OECD/NEA Forum on Stakeholder Confidence (FSC) was hosted by ONDRAF/NIRAS, the Belgian Agency for Radioactive Waste Management and enriched fissile materials. The central theme of the workshop was 'Dealing with interests, values and knowledge in managing risk' within the Belgian context of local partnerships for the long term management of low-level, short-lived radioactive waste. The four-day workshop started with a half-day session in Brussels giving a general introduction on the Belgian context and the local partnership methodology. This was followed by community visits to three local partnerships, PaLoFF in Fleurus-Farciennes, MONA in Mol, and STOLA in Dessel. After the visits, the workshop continued with two full-day sessions in Brussels. One hundred and nineteen registered participants, representing 13 countries, attended the workshop or participated in the community visits. About two thirds were Belgian stakeholders; the remainder came from FSC member organisations. The participants included representatives of municipal governments, civil society organisations, government agencies, industrial companies, the media, and international organisations as well as private citizens, consultants and academics. The four-day meeting was structured as follows: Day 1 morning was devoted to introductory presentations. Information was given on the general radioactive waste management context in Belgium. Regarding the management of LLW, and in particular the search for a disposal facility site, the workshop heard about the local partnership methodology developed by university researchers of the University of Antwerp and the Fondation Universitaire Luxembourgeoise (FUL). These partnerships between the potential host municipalities and the radwaste agency have the mission to develop an integrated facility proposal adapted to local conditions. Community visits took place on Day 1 afternoon and Day 2. Visits offered an opportunity for

Use of the GO methodology to assess plant operating data

International Nuclear Information System (INIS)

Wenger, L.O.; Danner, M.A.

1987-01-01

In September 1985, the Institute of Nuclear Power Operations (INPO) published The Operational Performance of Auxiliary Feedwater Systems in US PWRs, 1980-1984, in which many of the problems experienced by the nuclear industry with auxiliary feedwater systems (AFWSs) were summarized. The principal conclusions of the INPO report were that pressurized water reactor AFWS equipment failure rates had nearly doubled industry-wide since 1980. Calvert Cliffs Units 1 and 2 were highlighted by INPO as being among some of the poorer performers identified in the report. The study objective involved estimating the historical AFWS unavailability so that it could be compared with a predetermined acceptable availability goal. From this comparison, the relative importance of individual contributions to overall system unavailability resulting from various equipment failure modes could be assessed. The GO methodology, a computerized reliability analyses technique, was selected as the means for performing additional analyses. A GO system model was developed to represent the current Calvert Cliffs AFWS configuration. In summary, it was shown that integration of plant data with a comprehensive availability/reliability model can provide both the necessary insights to focus attention on the most important contributions to system unavailability and a pragmatic way for developing a cost effective implementation strategy. The GO methodology was useful and provided the requisite results with a minimal outlay of valuable resources

78 FR 17746 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2013-03-22

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... information in the summary is intended to affect the legal status of the petition or its final disposition...

78 FR 53185 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2013-08-28

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... information in the summary is intended to affect the legal status of the petition or its final disposition...

75 FR 19672 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2010-04-15

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... summary is intended to affect the legal status of the petition or its final disposition. DATES: Comments...

78 FR 46673 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2013-08-01

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... information in the summary is intended to affect the legal status of the petition or its final disposition...

75 FR 60164 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2010-09-29

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... information in the summary is intended to affect the legal status of the petition or its final disposition...

77 FR 2120 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2012-01-13

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... information in the summary is intended to affect the legal status of the petition or its final disposition...

78 FR 73918 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2013-12-09

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... summary is intended to affect the legal status of the petition or its final disposition. [[Page 73919...

78 FR 13746 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2013-02-28

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... summary is intended to affect the legal status of the petition or its final disposition. DATES: Comments...

76 FR 39975 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2011-07-07

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... summary is intended to affect the legal status of the petition or its final disposition. DATES: Comments...

78 FR 46672 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2013-08-01

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... information in the summary is intended to affect the legal status of the petition or its final disposition...

78 FR 978 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2013-01-07

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... information in the summary is intended to affect the legal status of the petition or its final disposition...

76 FR 14744 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2011-03-17

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... summary is intended to affect the legal status of the petition or its final disposition. DATES: Comments...

78 FR 36294 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2013-06-17

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... information in the summary is intended to affect the legal status of the petition or its final disposition...

78 FR 66986 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2013-11-07

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... information in the summary is intended to affect the legal status of the petition or its final disposition...

78 FR 39824 - Petition for Exemption; Summary of Petition Received

Science.gov (United States)

2013-07-02

...] Petition for Exemption; Summary of Petition Received AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of petition for exemption received. SUMMARY: This notice contains a summary of a petition... information in the summary is intended to affect the legal status of the petition or its final disposition...

LOW COST METHODOLOGIES TO ANALYZE AND CORRECT ABNORMAL PRODUCTION DECLINE IN STRIPPER GAS WELLS

International Nuclear Information System (INIS)

Jerry James; Gene Huck; Tim Knobloch

2001-01-01

A study group of 376 Clinton Sand wells in Ohio provided data to determine the historic frequency of the problem of abnormal production declines in stripper gas wells and the causes of the abnormal production decline. Analysis of the historic frequency of the problem indicates over 70% of the wells experienced abnormal production decline. The most frequently occurring causes of abnormal production declines were determined to be fluid accumulation (46%), gas gathering restrictions (24%), and mechanical failures (23%). Data collection forms and decision trees were developed to cost-effectively diagnose the abnormal production declines and suggest corrective action. The decision trees and data collection sheets were incorporated into a procedure guide to provide stripper gas well operators with a methodology to analyze and correct abnormal production declines. The systematic methodologies and techniques developed should increase the efficiency of problem well assessment and implementation of solutions for stripper gas wells. This eight quarterly technical progress report provides a summary of the deliverables completed to date, including the results of the remediations, the procedure guide, and the technology transfer. Due to the successful results of the study to date and the efficiency of the methodology development, two to three additional wells will be selected for remediation for inclusion into the study. The results of the additional remediations will be included in the final report

Examination of office visit patient preferences for the after-visit summary (AVS).

Science.gov (United States)

Neuberger, Marolee; Dontje, Katherine; Holzman, Greg; Corser, Bill; Keskimaki, Abigail; Chant, Ericka

2014-01-01

The federal government advocates the practice of routinely providing an after-visit summary (AVS) to patients after each office-based visit as an element of stage 1 meaningful use. A significant potential benefit of the AVS is improved patient engagement achieved by enabling patients and family members to better understand and retain key health information. The methodology for this study was a mixed-methods pilot study to examine, through the perspectives of adult primary care patients, how relevant and actionable data can be better formatted in the AVS. Results of this study suggest that the goal of the AVS to serve as a communication tool to engage and support patients is frequently not being met. Further study is needed to understand, from the viewpoints of patients and providers, what barriers are keeping them from optimally providing and using the information on the AVS.

RIBA Project - Risk-Informed approach for In-Service Inspection of Nuclear Power Plant Components. Project summary

International Nuclear Information System (INIS)

Lidbury, D.; Smith, G.

2001-12-01

The need for a European review of a Risk-Informed Approach for In-Service Inspection of Nuclear Power Plant Components (RIBA) was identified in 1998. This was as a priority item in the programme of activities conducted in the framework of the Council Resolutions of 22 July 1975 and of 18 June 1992 on the Technological Problems of Nuclear Safety. The RIBA Project was established in November 1999 as a 24-month Study Contract funded by the European Commission within the frame of the former DG XI WGCS (Working Group on Codes and Standards). The Study Contract was subsequently managed for the EC by DG TREN. The participants in RIBA were Serco Assurance (project coordinator), Ringhals AB, EDF, Tecnatom SA and Westinghouse Electric Europe. The work is presented in a summary report with the detailed results contained in three companion reports as follows: main conclusions and recommendations, Review of Existing Risk-Informed Methodologies, A Comparative Study of Risk-Informed In-Service Inspection Applications, Conclusions and Recommendations for Risk-Informed in-service inspection methodology applied to Nuclear Power Plants in Europe. (author)

Estimating summary statistics for electronic health record laboratory data for use in high-throughput phenotyping algorithms

Science.gov (United States)

Elhadad, N.; Claassen, J.; Perotte, R.; Goldstein, A.; Hripcsak, G.

2018-01-01

We study the question of how to represent or summarize raw laboratory data taken from an electronic health record (EHR) using parametric model selection to reduce or cope with biases induced through clinical care. It has been previously demonstrated that the health care process (Hripcsak and Albers, 2012, 2013), as defined by measurement context (Hripcsak and Albers, 2013; Albers et al., 2012) and measurement patterns (Albers and Hripcsak, 2010, 2012), can influence how EHR data are distributed statistically (Kohane and Weber, 2013; Pivovarov et al., 2014). We construct an algorithm, PopKLD, which is based on information criterion model selection (Burnham and Anderson, 2002; Claeskens and Hjort, 2008), is intended to reduce and cope with health care process biases and to produce an intuitively understandable continuous summary. The PopKLD algorithm can be automated and is designed to be applicable in high-throughput settings; for example, the output of the PopKLD algorithm can be used as input for phenotyping algorithms. Moreover, we develop the PopKLD-CAT algorithm that transforms the continuous PopKLD summary into a categorical summary useful for applications that require categorical data such as topic modeling. We evaluate our methodology in two ways. First, we apply the method to laboratory data collected in two different health care contexts, primary versus intensive care. We show that the PopKLD preserves known physiologic features in the data that are lost when summarizing the data using more common laboratory data summaries such as mean and standard deviation. Second, for three disease-laboratory measurement pairs, we perform a phenotyping task: we use the PopKLD and PopKLD-CAT algorithms to define high and low values of the laboratory variable that are used for defining a disease state. We then compare the relationship between the PopKLD-CAT summary disease predictions and the same predictions using empirically estimated mean and standard deviation to a

Estimating summary statistics for electronic health record laboratory data for use in high-throughput phenotyping algorithms.

Science.gov (United States)

Albers, D J; Elhadad, N; Claassen, J; Perotte, R; Goldstein, A; Hripcsak, G

2018-02-01

We study the question of how to represent or summarize raw laboratory data taken from an electronic health record (EHR) using parametric model selection to reduce or cope with biases induced through clinical care. It has been previously demonstrated that the health care process (Hripcsak and Albers, 2012, 2013), as defined by measurement context (Hripcsak and Albers, 2013; Albers et al., 2012) and measurement patterns (Albers and Hripcsak, 2010, 2012), can influence how EHR data are distributed statistically (Kohane and Weber, 2013; Pivovarov et al., 2014). We construct an algorithm, PopKLD, which is based on information criterion model selection (Burnham and Anderson, 2002; Claeskens and Hjort, 2008), is intended to reduce and cope with health care process biases and to produce an intuitively understandable continuous summary. The PopKLD algorithm can be automated and is designed to be applicable in high-throughput settings; for example, the output of the PopKLD algorithm can be used as input for phenotyping algorithms. Moreover, we develop the PopKLD-CAT algorithm that transforms the continuous PopKLD summary into a categorical summary useful for applications that require categorical data such as topic modeling. We evaluate our methodology in two ways. First, we apply the method to laboratory data collected in two different health care contexts, primary versus intensive care. We show that the PopKLD preserves known physiologic features in the data that are lost when summarizing the data using more common laboratory data summaries such as mean and standard deviation. Second, for three disease-laboratory measurement pairs, we perform a phenotyping task: we use the PopKLD and PopKLD-CAT algorithms to define high and low values of the laboratory variable that are used for defining a disease state. We then compare the relationship between the PopKLD-CAT summary disease predictions and the same predictions using empirically estimated mean and standard deviation to a

Acceleration-based methodology to assess the blast mitigation performance of explosive ordnance disposal helmets

Science.gov (United States)

Dionne, J. P.; Levine, J.; Makris, A.

2018-01-01

To design the next generation of blast mitigation helmets that offer increasing levels of protection against explosive devices, manufacturers must be able to rely on appropriate test methodologies and human surrogates that will differentiate the performance level of various helmet solutions and ensure user safety. Ideally, such test methodologies and associated injury thresholds should be based on widely accepted injury criteria relevant within the context of blast. Unfortunately, even though significant research has taken place over the last decade in the area of blast neurotrauma, there currently exists no agreement in terms of injury mechanisms for blast-induced traumatic brain injury. In absence of such widely accepted test methods and injury criteria, the current study presents a specific blast test methodology focusing on explosive ordnance disposal protective equipment, involving the readily available Hybrid III mannequin, initially developed for the automotive industry. The unlikely applicability of the associated brain injury criteria (based on both linear and rotational head acceleration) is discussed in the context of blast. Test results encompassing a large number of blast configurations and personal protective equipment are presented, emphasizing the possibility to develop useful correlations between blast parameters, such as the scaled distance, and mannequin engineering measurements (head acceleration). Suggestions are put forward for a practical standardized blast testing methodology taking into account limitations in the applicability of acceleration-based injury criteria as well as the inherent variability in blast testing results.

Systematic review of the diagnostic accuracy of the non-English versions of Addenbrooke's cognitive examination - revised and III.

Science.gov (United States)

Habib, Noor; Stott, Joshua

2017-12-11

This systematic review aims to review the evidence for the diagnostic accuracy of the non-English updated versions of Addenbrooke's Cognitive Examination (ACE) - the ACE-Revised (ACE-R) and the ACE-III - in the diagnosis of dementia. A systematic search resulted in 16 eligible studies evaluating the diagnostic accuracy of ACE-R and ACE-III in ten different languages. Most studies were assessed as of medium to low quality using Standards for Reporting of Diagnostic Accuracy (STARD) guidance. The findings of excellent diagnostic accuracy are compromised by the methodological limitations of studies. While studies generally reported excellent diagnostic accuracy across and within different languages, optimal cut-offs even within particular language versions, varied. There is a need for future research to address these limitations through adherence to STARD guidelines. The ACE-III is particularly under-evaluated and should be a focus of future research. The variance in obtained optimal cut-offs within language versions is an issue compromising clinical utility and could be addressed in future work through use of a-priori defined thresholds.

Advanced fusion concepts project summaries, FY 1988

International Nuclear Information System (INIS)

1988-04-01

This report summarizes all the projects supported by the Advanced Fusion Concepts Branch of the Applied Plasma Physics Division of the Office of Fusion Energy, US Department of Energy. Each project summary was written by the respective principal investigator using the format: title, principal investigators, funding levels, purpose, approach, progress, plans, milestones, graduate students, graduates, other professional staff, and recent publications. This report is organized into three sections: Section one contains five summaries describing work in the reversed-field pinch program being performed by a diversified group of contractors, these include a national laboratory, a private company, and several universities. Section two contains eight summaries of work from the compact toroid area which encompasses field-reversed configurations, spheromaks, and heating and formation experiments. Section three contains summaries from two other programs, a density Z-pinch experiment and high-beta Q machine experiment. The intent of this collection of project summaries is to help the contractors of the Advanced Fusion Concepts Branch understand their relationship with the rest of the branch's activities. It is also meant to provide background to those outside the program by showing the range of activities of interest of the Advanced Fusion Concepts Branch

Assessing the worth of electric products and services in a new competitive marketplace: A review of market research methodologies and analytic tools

Energy Technology Data Exchange (ETDEWEB)

Cosgrove, S.J.; Spitzer, L. [AUS Consultants, Media, PA (United States)

1994-11-01

As electric utilities move from a heavily regulated environment to less regulated, differently regulated, or competitive environment, the importance of determining the relative value of products and services. We begin by examining the traditional method of assessing importance, rating scales. Then we look at other methodologies, such as multiple paired comparisons, constant sum, regression techniques, and hypothetical choice models. After discussing these methodologies, we demonstrate how they can be applied. We conclude by providing a summary of methods for assessing the worth of electric products and services. For most marketing studies, several criteria or attributes are identified as having an impact on the customer`s evaluation of a product and service. These criteria usually involve several aspects of both the product and service attributes.

Summary and synthesis: How to present a research proposal

Directory of Open Access Journals (Sweden)

Maninder Singh Setia

2017-01-01

Full Text Available This concluding module attempts to synthesize the key learning points discussed during the course of the previous ten sets of modules on methodology and biostatistics. The objective of this module is to discuss how to present a model research proposal, based on whatever was discussed in the preceding modules. The lynchpin of a research proposal is the protocol, and the key component of a protocol is the study design. However, one must not neglect the other areas, be it the project summary through which one catches the eyes of the reviewer of the proposal, or the background and the literature review, or the aims and objectives of the study. Two critical areas in the “methods” section that cannot be emphasized more are the sampling strategy and a formal estimation of sample size. Without a legitimate sample size, none of the conclusions based on the statistical analysis would be valid. Finally, the ethical parameters of the study should be well understood by the researchers, and that should get reflected in the proposal.

Summary and Synthesis: How to Present a Research Proposal.

Science.gov (United States)

Setia, Maninder Singh; Panda, Saumya

2017-01-01

This concluding module attempts to synthesize the key learning points discussed during the course of the previous ten sets of modules on methodology and biostatistics. The objective of this module is to discuss how to present a model research proposal, based on whatever was discussed in the preceding modules. The lynchpin of a research proposal is the protocol, and the key component of a protocol is the study design. However, one must not neglect the other areas, be it the project summary through which one catches the eyes of the reviewer of the proposal, or the background and the literature review, or the aims and objectives of the study. Two critical areas in the "methods" section that cannot be emphasized more are the sampling strategy and a formal estimation of sample size. Without a legitimate sample size, none of the conclusions based on the statistical analysis would be valid. Finally, the ethical parameters of the study should be well understood by the researchers, and that should get reflected in the proposal.

Temporal development of cross-neutralization between HTLV-III B and HTLV-III RF in experimentally infected chimpanzees

NARCIS (Netherlands)

Goudsmit, J.; Thiriart, C.; Smit, L.; Bruck, C.; Gibbs, C. J.

1988-01-01

Sera from chimpanzees inoculated respectively with HTLV-III B, LAV, HTLV-III RF and brain tissue from an AIDS patient were analysed for neutralizing activity by two methods: a cell fusion inhibition test (CFI) using HTLV-III B infected cells as inoculum and CD4+ cells as target and a replication

Radiometric titration of thallium(III) with EDTA

International Nuclear Information System (INIS)

Rao, V.R.S.; Pulla Rao, Ch.; Tataiah, G.

1978-01-01

Radioactive solutions containing very small amounts of thallium(III) can be determined by radiometric titration using ammonia as hydrolysing agent. Aqueous solution of thallium(I) (both inactive and radioactive) is treated with bromine water till the appearance of the brown colour of bromine, and the solution is warmed to 80 deg C to expel the excess bromine. By this procedure all thallium(I) is quantitatively oxidised to thallium(III). An aqueous solution of ammonia is added to precipitate thallium(III) as thallic oxide. It is then filtered, washed with water to free it from bromide and then dissolved in 2N HCl and the solution is then standardised. 2 ml of this solution is transferred to a 20 ml volumetric flask, 1 ml of radioactive thallium(III) solution to be standardised is added as well as incremental amounts of EDTA solution and mixed thoroughly. Uncomplexed thallium(III) is then precipitated by the addition of an ammonia solution and diluted to 20 ml. Required amount of this mixture is centrifuged. The beta activity of the supernatant aliquot is measured using a GM counter. Quantitative determination of Tl(III) in the range of 1-10 μM can be carried out. The interference of cations such as Au(III), iron(III), Ga(III) can be eliminated by pretreatment of the Tl(III) solution before carrying out radiometric titration. The results obtained are reproducible and accurate to +-3%. (T.I.)

Complex-wide review of DOE's Low-Level Waste Management ES ampersand H vulnerabilities. Volume II. Final report

International Nuclear Information System (INIS)

1996-05-01

Volume I of this report presents a summary of DOE's complex-wide review of its low-level waste management system, including the assessment scope and methodology, site-specific and complex-wide vulnerabilities, and DOE's conclusions and recommendations. Volume II presents a more detailed discussion of the assessment methodology and evaluation instruments developed by the Assessment Working Group for identifying site-specific vulnerabilities, categorizing and classifying vulnerabilities, and identifying and analyzing complex-wide vulnerabilities. Attachments A and B of this volume contain, respectively, the Site Evaluation Survey and the Vulnerability Assessment Form used in those processes. Volume III contains the site-specific assessment reports for the 36 sites (38 facilities) assessed in the complex-wide review from which the complex-wide vulnerabilities were drawn

Single-molecule magnetism in three related {Co(III)2Dy(III)2}-acetylacetonate complexes with multiple relaxation mechanisms.

Science.gov (United States)

Langley, Stuart K; Chilton, Nicholas F; Moubaraki, Boujemaa; Murray, Keith S

2013-06-17

Three new heterometallic complexes with formulas of [Dy(III)2Co(III)2(OMe)2(teaH)2(acac)4(NO3)2] (1), [Dy(III)2Co(III)2(OH)2(teaH)2(acac)4(NO3)2]·4H2O (2), and [Dy(III)2Co(III)2(OMe)2(mdea)2(acac)4(NO3)2] (3) were characterized by single-crystal X-ray diffraction and by dc and ac magnetic susceptibility measurements. All three complexes have an identical "butterfly"-type metallic core that consists of two Dy(III) ions occupying the "body" position and two diamagnetic low-spin Co(III) ions occupying the outer "wing-tips". Each complex displays single-molecule magnet (SMM) behavior in zero applied magnetic field, with thermally activated anisotropy barriers of 27, 28, and 38 K above 7.5 K for 1-3, respectively, as well as observing a temperature-independent mechanism of relaxation below 5 K for 1 and 2 and at 3 K for 3, indicating fast quantum tunneling of magnetization (QTM). A second, faster thermally activated relaxation mechanism may also be active under a zero applied dc field as derived from the Cole-Cole data. Interestingly, these complexes demonstrate further relaxation modes that are strongly dependent upon the application of a static dc magnetic field. Dilution experiments that were performed on 1, in the {Y(III)2Co(III)2} diamagnetic analog, show that the slow magnetic relaxation is of a single-ion origin, but it was found that the neighboring ion also plays an important role in the overall relaxation dynamics.

III-V microelectronics

CERN Document Server

Nougier, JP

1991-01-01

As is well known, Silicon widely dominates the market of semiconductor devices and circuits, and in particular is well suited for Ultra Large Scale Integration processes. However, a number of III-V compound semiconductor devices and circuits have recently been built, and the contributions in this volume are devoted to those types of materials, which offer a number of interesting properties. Taking into account the great variety of problems encountered and of their mutual correlations when fabricating a circuit or even a device, most of the aspects of III-V microelectronics, from fundamental p

Antithrombin III for critically ill patients

DEFF Research Database (Denmark)

Allingstrup, Mikkel; Wetterslev, Jørn; Ravn, Frederikke B

2016-01-01

PURPOSE: Antithrombin III (AT III) is an anticoagulant with anti-inflammatory properties. We assessed the benefits and harms of AT III in critically ill patients. METHODS: We searched from inception to 27 August 2015 in CENTRAL, MEDLINE, EMBASE, CAB, BIOSIS and CINAHL. We included randomized...... participants). However, for all other outcome measures and analyses, the results did not reach statistical significance. CONCLUSIONS: There is insufficient evidence to support AT III substitution in any category of critically ill participants including those with sepsis and DIC. AT III did not show an impact...

Structured methodology review identified seven (RETREAT) criteria for selecting qualitative evidence synthesis approaches.

Science.gov (United States)

Booth, Andrew; Noyes, Jane; Flemming, Kate; Gerhardus, Ansgar; Wahlster, Philip; van der Wilt, Gert Jan; Mozygemba, Kati; Refolo, Pietro; Sacchini, Dario; Tummers, Marcia; Rehfuess, Eva

2018-07-01

To compare and contrast different methods of qualitative evidence synthesis (QES) against criteria identified from the literature and to map their attributes to inform selection of the most appropriate QES method to answer research questions addressed by qualitative research. Electronic databases, citation searching, and a study register were used to identify studies reporting QES methods. Attributes compiled from 26 methodological papers (2001-2014) were used as a framework for data extraction. Data were extracted into summary tables by one reviewer and then considered within the author team. We identified seven considerations determining choice of methods from the methodological literature, encapsulated within the mnemonic Review question-Epistemology-Time/Timescale-Resources-Expertise-Audience and purpose-Type of data. We mapped 15 different published QES methods against these seven criteria. The final framework focuses on stand-alone QES methods but may also hold potential when integrating quantitative and qualitative data. These findings offer a contemporary perspective as a conceptual basis for future empirical investigation of the advantages and disadvantages of different methods of QES. It is hoped that this will inform appropriate selection of QES approaches. Copyright © 2018 Elsevier Inc. All rights reserved.

Electron and muon physics sessions: Summary

International Nuclear Information System (INIS)

Montgomery, H.E.

1988-06-01

The electromagnetic interaction needs no introduction as a probe of the structure of systems on many scales. The continued use of this technique dominated the sessions on Electron and Muon Physics at the Samoset Meeting. The experimental results continue to stimulate large numbers of theorists and the results on polarized deep inelastic muon scattering and their various interpretations permeated beyond these sessions. The breadth of physics attacked with electrons and muons makes a summary such as this rather peculiar. As one of my nuclear physics friends (I think) commented after my summary, ''it was interesting to see Nuclear Physics from a long distance with the telescope inverted.'' The comment may well be applied to this written version of the summary talk. 21 refs

A methodology for collection and analysis of human error data based on a cognitive model: IDA

International Nuclear Information System (INIS)

Shen, S.-H.; Smidts, C.; Mosleh, A.

1997-01-01

This paper presents a model-based human error taxonomy and data collection. The underlying model, IDA (described in two companion papers), is a cognitive model of behavior developed for analysis of the actions of nuclear power plant operating crew during abnormal situations. The taxonomy is established with reference to three external reference points (i.e. plant status, procedures, and crew) and four reference points internal to the model (i.e. information collected, diagnosis, decision, action). The taxonomy helps the analyst: (1) recognize errors as such; (2) categorize the error in terms of generic characteristics such as 'error in selection of problem solving strategies' and (3) identify the root causes of the error. The data collection methodology is summarized in post event operator interview and analysis summary forms. The root cause analysis methodology is illustrated using a subset of an actual event. Statistics, which extract generic characteristics of error prone behaviors and error prone situations are presented. Finally, applications of the human error data collection are reviewed. A primary benefit of this methodology is to define better symptom-based and other auxiliary procedures with associated training to minimize or preclude certain human errors. It also helps in design of control rooms, and in assessment of human error probabilities in the probabilistic risk assessment framework. (orig.)

A view from Cheyenne Mountain: Generation III's perspective of Keystone III.

Science.gov (United States)

Bliss, Erika; Cadwallader, Kara; Steyer, Terrence E; Clements, Deborah S; Devoe, Jennifer E; Fink, Kenneth; Khubesrian, Marina; Lyons, Paul; Steiner, Elizabeth; Weismiller, David

2014-01-01

In October 2000 the family of family medicine convened the Keystone III conference at Cheyenne Mountain Resort. Keystone III participants included members of Generation I (entered practice before 1970), Generation II (entered 1970-1990), and Generation III (entered after 1990). They represented a wide range of family physicians, from medical students to founders of the discipline, and from small-town solo practice to academic medicine. During the conference, the three generations worked together and separately thinking about the past, present, and future of family medicine, our roles in it, and how the understanding of a family physician and our discipline had and would continue to evolve. After the conference, the 10 Generation III members wrote the article published here, reflecting on our experiences as new physicians and physicians in training, and the similarities and differences between our experiences and those of physicians in Generations I and II. Key similarities included commitment to whole-person care, to a wide scope of practice, to community health, and to ongoing engagement with our discipline. Key differences included our understanding of availability, the need for work-life balance, the role of technology in the physician-patient relationship, and the perceptions of the relationship between medicine and a range of outside forces such as insurance and government. This article, presented with only minor edits, thus reflects accurately our perceptions in late 2000. The accompanying editorial reflects our current perspective.

Spectroscopic investigations on the complexation of Cm(III) and Eu(III) with organic model ligands and their binding mode in human urine (in vitro); Spektroskopische Untersuchungen zur Komplexbildung von Cm(III) und Eu(III) mit organischen Modellliganden sowie ihrer chemischen Bindungsform in menschlichem Urin (in vitro)

Energy Technology Data Exchange (ETDEWEB)

Heller, Anne

2011-10-26

In case of incorporation, trivalent actinides (An(III)) and lanthanides (Ln(III)) pose a serious health risk to humans. An(III) are artificial, highly radioactive elements which are mainly produced during the nuclear fuel cycle in nuclear power plants. Via hazardous accidents or nonprofessional storage of radioactive waste, they can be released in the environment and enter the human food chain. In contrast, Ln(III) are nonradioactive, naturally occurring elements with multiple applications in technique and medicine. Consequently it is possible that humans get in contact and incorporate both, An(III) and Ln(III). Therefore, it is of particular importance to elucidate the behaviour of these elements in the human body. While macroscopic processes such as distribution, accumulation and excretion are studied quite well, knowledge about the chemical binding form (speciation) of An(III) and Ln(III) in various body fluids is still sparse. In the present work, for the first time, the speciation of Cm(III) and Eu(III) in natural human urine (in vitro) has been investigated spectroscopically and the formed complex identified. For this purpose, also basic investigations on the complex formation of Cm(III) and Eu(III) in synthetic model urine as well as with the urinary relevant, organic model ligands urea, alanine, phenylalanine, threonine and citrate have been performed and the previously unknown complex stability constants determined. Finally, all experimental results were compared to literature data and predictions calculated by thermodynamic modelling. Since both, Cm(III) and Eu(III), exhibit unique luminescence properties, particularly the suitability of time-resolved laser-induced fluorescence spectroscopy (TRLFS) could be demonstrated as a method to investigate these metal ions in untreated, complex biofluids. The results of this work provide new scientific findings on the biochemical reactions of An(III) and Ln(III) in human body fluids on a molecular scale and

Antithrombin III for critically ill patients

DEFF Research Database (Denmark)

Allingstrup, Mikkel; Wetterslev, Jørn; Ravn, Frederikke B

2016-01-01

Background: Critical illness is associated with uncontrolled inflammation and vascular damage which can result in multiple organ failure and death. Antithrombin III (AT III) is an anticoagulant with anti-inflammatory properties but the efficacy and any harmful effects of AT III supplementation...... in critically ill patients are unknown. This review was published in 2008 and updated in 2015.  Objectives: To examine: 1. The effect of AT III on mortality in critically ill participants. 2. The benefits and harms of AT III. We investigated complications specific and not specific to the trial intervention......, bleeding events, the effect on sepsis and disseminated intravascular coagulation (DIC) and the length of stay in the intensive care unit (ICU) and in hospital in general.  Search methods: We searched the following databases from inception to 27 August 2015: Cochrane Central Register of Controlled Trials...

Operating reactors licensing actions summary

International Nuclear Information System (INIS)

1982-07-01

The operating reactors licensing actions summary is designed to provide the management of the Nuclear Regulatory Commission (NRC) with an overview of licensing actions dealing with operating power and nonpower reactors. These reports utilize data collected from the Division of Licensing in the Office of Nuclear Reactor Regulation and are prepared by the Office of Management and Program Analysis. This summary report is published primarily for internal NRC use in managing the operating reactors licensing actions program. Its content will change based on NRC management informational requirements

Operating reactors licensing actions summary

International Nuclear Information System (INIS)

1982-05-01

The operating reactors licensing actions summary is designed to provide the management of the Nuclear Regulatory Commission (NRC) with an overview of licensing actions dealing with operating power and nonpower reactors. These reports utilize data collected from the Division of Licensing in the Office of Nuclear Reactor Regulation and are prepared by the Office of Management and Program Analysis. This summary report is published primarily for internal NRC use in managing the operating reactors licensing actions program. Its content will change based on NRC management informational requirements

Operating reactors licensing actions summary

International Nuclear Information System (INIS)

1983-01-01

The operating reactors licensing actions summary is designed to provide the management of the Nuclear Regulatory Commission (NRC) with an overview of licensing actions dealing with operating power and nonpower reactors. These reports utilize data collected from the Division of Licensing in the Office of Nuclear Reactor Regulation and are prepared by the Office of Management and Program Analysis. This summary report is published primarily for internal NRC use in managing the operating reactors licensing actions program. Its content will change based on NRC management informational requirements

Operating reactors licensing actions summary

International Nuclear Information System (INIS)

1983-03-01

The operating reactors licensing actions summary is designed to provide the management of the Nuclear Regulatory Commission (NRC) with an overview of licensing actions dealing with operating power and nonpower reactors. These reports utilize data collected from the Division of Licensing in the Office of Nuclear Reactor Regulation and are prepared by the Office of Management and Program Analysis. This summary report is published primarily for internal NRC use in managing the operating reactors licensing actions program. Its content will change based on NRC management informational requirements

Operating reactors licensing actions summary

International Nuclear Information System (INIS)

1982-11-01

The operating reactors licensing actions summary is designed to provide the management of the Nuclear Regulatory Commission (NRC) with an overview of licensing actions dealing with operating power and nonpower reactors. These reports utilize data collected from the Division of Licensing in the Office of Nuclear Reactor Regulation and are prepared by the Office of Management and Program Analysis. This summary report is published primarily for internal NRC use in managing the operating reactors licensing actions program. Its content will change based on NRC management informational requirements

Operating reactors licensing actions summary

International Nuclear Information System (INIS)

1982-10-01

The operating reactors licensing actions summary is designed to provide the management of the Nuclear Regulatory Commission (NRC) with an overview of licensing actions dealing with operating power and nonpower reactors. These reports utilize data collected from the Division of Licensing in the Office of Nuclear Reactor Regulation and are prepared by the Office of Management and Program Analysis. This summary report is published primarily for internal NRC use in managing the operating reactors licensing actions program. Its content will change based on NRC management informational requirements

Operating reactors licensing actions summary

International Nuclear Information System (INIS)

1982-08-01

The operating reactors licensing actions summary is designed to provide the management of the Nuclear Regulatory Commission (NRC) with an overview of licensing actions dealing with operating power and nonpower reactors. These reports utilize data collected from the Division of Licensing in the Office of Nuclear Reactor Regulation and are prepared by the Office of Management and Program Analysis. This summary report is published primarily for internal NRC use in managing the operating reactors licensing actions program. Its content will change based on NRC management informational requirements

Operating reactors licensing actions summary

International Nuclear Information System (INIS)

1982-09-01

The operating reactors licensing actions summary is designed to provide the management of the Nuclear Regulatory Commission (NRC) with an overview of licensing actions dealing with operating power and nonpower reactors. These reports utilize data collected from the Division of Licensing in the Office of Nuclear Reactor Regulation and are prepared by the Office of Management and Program Analysis. This summary report is published primarily for internal NRC use in managing the operating reactors licensing actions program. Its content will change based on NRC management informational requirements

Nutritional biomarkers and foodomic methodologies for qualitative and quantitative analysis of bioactive ingredients in dietary intervention studies.

Science.gov (United States)

Puiggròs, Francesc; Solà, Rosa; Bladé, Cinta; Salvadó, Maria-Josepa; Arola, Lluís

2011-10-21

Traditional dietary assessment methods, such as 24-h recalls, weighted food diaries and food frequency questionnaires (FFQs) are highly subjective and impair the assessment of successfully accomplished dietary interventions. Foodomic technologies offer promising methodologies for gathering scientific evidence from clinical trials with sensitive methods (e.g., GC-MS, LC-MS, CE, NMR) to detect and quantify markers of nutrient exposure or subtle changes in dietary patterns. This review provides a summary of recently developed foodomic methodologies for the detection of suggested biomarkers, including the food specificity for each suggested biomarker and a brief description of the key aspects of 24-h recalls that may affect marker detection and stability, such as mixed nutrients and cooking processes. The primary aim of this review is to contribute to the assessment of the metabolic effects of active ingredients and foods using cutting-edge methods to improve approaches to future nutritional programs tailored for health maintenance and disease prevention. Copyright © 2011 Elsevier B.V. All rights reserved.

Summary of discussion

International Nuclear Information System (INIS)

2006-01-01

This document provides summaries of the discussions occurred during the second international workshop on the indemnification of nuclear damage. It concerns the second accident scenario: a fire on board of a ship transporting enriched uranium hexafluoride along the Danube River. (A.L.B.)

Summary of Trends

Indian Academy of Sciences (India)

First page Back Continue Last page Overview Graphics. Summary of Trends. Optical Ethernet: Direct Ethernet connectivity to businesses through optical fiber. Automation of network infrastructure: Cross-connects for interconnections; Intelligence through software for OA&M. New “data-centric” protection mechanisms ...

Addition compounds of lanthamide (III) and yttrium (III) hexafluorophosphates and N,N - dimethylformamide

International Nuclear Information System (INIS)

Braga, L.S.P.

1983-01-01

Addition compounds of lanthanide (III) and yttrium (III) hexafluorophosphates and N-N-Dimetylformamide are described to characterize the complexes, elemental analysis, melting ranges, molar conductance measurements, X-ray powder patters infrared and Raman spectra, TG and DTA curves, are studied. Information concerning the decomposition of the adducts through the thermogravimetric curves and the differential thermal analysis curves is obtained. (M.J.C.) [pt

Characterization of Fe (III)-reducing enrichment culture and isolation of Fe (III)-reducing bacterium Enterobacter sp. L6 from marine sediment.

Science.gov (United States)

Liu, Hongyan; Wang, Hongyu

2016-07-01

To enrich the Fe (III)-reducing bacteria, sludge from marine sediment was inoculated into the medium using Fe (OH)3 as the sole electron acceptor. Efficiency of Fe (III) reduction and composition of Fe (III)-reducing enrichment culture were analyzed. The results indicated that the Fe (III)-reducing enrichment culture with the dominant bacteria relating to Clostridium and Enterobacter sp. had high Fe (III) reduction of (2.73 ± 0.13) mmol/L-Fe (II). A new Fe (III)-reducing bacterium was isolated from the Fe (III)-reducing enrichment culture and identified as Enterobacter sp. L6 by 16S rRNA gene sequence analysis. The Fe (III)-reducing ability of strain L6 under different culture conditions was investigated. The results indicated that strain L6 had high Fe (III)-reducing activity using glucose and pyruvate as carbon sources. Strain L6 could reduce Fe (III) at the range of NaCl concentrations tested and had the highest Fe (III) reduction of (4.63 ± 0.27) mmol/L Fe (II) at the NaCl concentration of 4 g/L. This strain L6 could reduce Fe (III) with unique properties in adaptability to salt variation, which indicated that it can be used as a model organism to study Fe (III)-reducing activity isolated from marine environment. Copyright © 2015 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

A binuclear Fe(III)Dy(III) single molecule magnet. Quantum effects and models.

Science.gov (United States)

Ferbinteanu, Marilena; Kajiwara, Takashi; Choi, Kwang-Yong; Nojiri, Hiroyuki; Nakamoto, Akio; Kojima, Norimichi; Cimpoesu, Fanica; Fujimura, Yuichi; Takaishi, Shinya; Yamashita, Masahiro

2006-07-19

The binuclear [FeIII(bpca)(mu-bpca)Dy(NO3)4], having Single Molecule Magnet (SMM) properties, belonging to a series of isostructural FeIIILnIII complexes (Ln = Eu, Gd, Tb, Dy, Ho) and closely related FeIILnIII chain structures, was characterized in concise experimental and theoretical respects. The low temperature magnetization data showed hysteresis and tunneling. The anomalous temperature dependence of Mössbauer spectra is related to the onset of magnetic order, consistent with the magnetization relaxation time scale resulting from AC susceptibility measurements. The advanced ab initio calculations (CASSCF and spin-orbit) revealed the interplay of ligand field, spin-orbit, and exchange effects and probed the effective Ising nature of the lowest states, involved in the SMM and tunneling effects.

Summaries of FY 1996 engineering research

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

This report documents the Basic Energy Sciences (BES) Engineering Research Program for fiscal year 1996; it provides a summary for each of the program projects in addition to a brief program overview. The report is intended to provide staff of Congressional committees, other executive departments, and other DOE offices with substantive program information so as to facilitate governmental overview and coordination of Federal research programs. Of equal importance, its availability facilitates communication of program information to interested research engineers and scientists. Each BES Division administers basic, mission oriented research programs in the area indicated by its title. The BES Engineering Research Program is one such program; it is administered by the Engineering and Geosciences Division of BES. In preparing this report the principal investigators were asked to submit summaries for their projects that were specifically applicable to fiscal year 1996. The summaries received have been edited if necessary, but the press for timely publication made it impractical to have the investigators review and approve the revised summaries prior to publication. For more information about a given project, it is suggested that the investigators be contacted directly.

The summary of national environmental restoration needs

International Nuclear Information System (INIS)

1993-07-01

The Office of Technology Development of the US Department of Energy (DOE) has directed the Savannah River Technology Center to implement an Integrated Demonstration Program at Savannah River Site to assess new environmental remediation systems and technologies and transfer them to other DOE sites and private industry for use in full-scale remediation efforts. The first phase of the Integrated Demonstration Program is coming to a successful conclusion and the Savannah River Technology Center has asked a panel of environmental experts to prioritize national, DOE, and Savannah River Site environmental problems and make programmatic recommendations for future technology research and demonstrations. This document is a summary of national and DOE environmental problems that are common to Savannah River Site and was created as a decision making tool for the expert panel. There are many diverse environmental problems, therefore the summary has been limited to environmental problems that are significant to the Savannah River Site. National environmental problems identified in the summary are soil and water contaminated with organic compounds. Specifically, groundwater contaminated with dense non-aqueous phase liquid hydrocarbons was found to be a significant national environmental problem. The DOE environmental problems identified in the summary are soil and water contaminated with fuel and chlorinated hydrocarbon compounds, metal compounds, and radioactive elements. Savannah River Site environmental problems identified in the summary are soil and groundwater contaminated with chlorinated hydrocarbons, metal compounds, tritiated water, and other radioactive elements. Technology deficiencies that were identified in the summary were deficiencies in in situ remediation technologies, in situ characterization technologies, and in situ isolation and containment technologies

9,10-phenanthrenesemiquinone radical complexes of ruthenium(III), osmium(III) and rhodium(III) and redox series.

Science.gov (United States)

Biswas, Manas Kumar; Patra, Sarat Chandra; Maity, Amarendra Nath; Ke, Shyue-Chu; Weyhermüller, Thomas; Ghosh, Prasanta

2013-05-14

Reactions of 9,10-phenanthrenequinone (PQ) in toluene with [M(II)(PPh3)3X2] at 298 K afford green complexes, trans-[M(PQ)(PPh3)2X2] (M = Ru, X = Cl, 1; M = Os, X = Br, 2) in moderate yields. Reaction of anhydrous RhCl3 with PQ and PPh3 in boiling ethanol affords the dark brown paramagnetic complex, cis-[Rh(PQ)(PPh3)2Cl2] (3) in good yields. Diffusion of iodine solution in n-hexane to the trans-[Os(PQ) (PPh3)2(CO)(Br)] solution in CH2Cl2 generates the crystals of trans-[Os(PQ)(PPh3)2(CO)(Br)](+)I3(-), (4(+))I3(-)), in lower yields. Single crystal X-ray structure determinations of 1·2toluene, 2·CH2Cl2 and 4(+)I3(-), UV-vis/NIR absorption spectra, EPR spectra of 3, electrochemical activities and DFT calculations on 1, 2, trans-[Ru(PQ)(PMe3)2Cl2] (1Me), trans-[Os(PQ)(PMe3)2Br2] (2Me), cis-[Rh(PQ)(PMe3)2Cl2] (3Me) and their oxidized and reduced analogues including trans-[Os(PQ)(PMe3)2(CO)(Br)](+) (4Me(+)) substantiated that 1-3 are the 9,10-phenanthrenesemiquinone radical (PQ(˙-)) complexes of ruthenium(III), osmium(III) and rhodium(III) and are defined as trans/cis-[M(III)(PQ(˙-))(PPh3)2X2] with a minor contribution of the resonance form trans/cis-[M(II)(PQ)(PPh3)2X2]. Two comparatively longer C-O (1.286(4) Å) and the shorter C-C lengths (1.415(7) Å) of the OO-chelate of 1·2toluene and 2·CH2Cl2 and the isotropic fluid solution EPR signal at g = 1.999 of 3 are consistent with the existence of the reduced PQ(˙-) ligand in 1-3 complexes. Anisotropic EPR spectra of the frozen glasses (g11 = g22 = 2.0046 and g33 = 1.9874) and solids (g11 = g22 = 2.005 and g33 = 1.987) instigate the contribution of the resonance form, cis-[Rh(II)(PQ)(PPh3)2Cl2] in 3. DFT calculations established that the closed shell singlet (CSS) solutions of 1Me and 2Me are unstable due to open shell singlet (OSS) perturbation. However, the broken symmetry (BS) (1,1) Ms = 0 solutions of 1Me and 2Me are respectively 22.6 and 24.2 kJ mole(-1) lower in energy and reproduced the experimental bond

Minerals Yearbook, volume III, Area Reports—International—Europe and Central Eurasia

Science.gov (United States)

Geological Survey, U.S.

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Minerals Yearbook, volume III, Area Reports—International—Asia and the Pacific

Science.gov (United States)

Geological Survey, U.S.

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Minerals Yearbook, volume III, Area Reports—International—Latin America and Canada

Science.gov (United States)

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Simultaneous Oxidation and Sequestration of As(III) from Water by Using Redox Polymer-Based Fe(III) Oxide Nanocomposite.

Science.gov (United States)

Zhang, Xiaolin; Wu, Mengfei; Dong, Hao; Li, Hongchao; Pan, Bingcai

2017-06-06

Water decontamination from As(III) is an urgent but still challenging task. Herein, we fabricated a bifunctional nanocomposite HFO@PS-Cl for highly efficient removal of As(III), with active chlorine covalently binding spherical polystyrene host for in situ oxidation of As(III) to As(V), and Fe(III) hydroxide (HFO) nanoparticles (NPs) embedded inside for specific As(V) removal. HFO@PS-Cl could work effectively in a wide pH range (5-9), and other substances like sulfate, chloride, bicarbonate, silicate, and humic acid exert insignificant effect on As(III) removal. As(III) sequestration is realized via two pathways, that is, oxidation to As(V) by the active chlorine followed by specific As(V) adsorption onto HFO NPs, and As(III) adsorption onto HFO NPs followed by oxidation to As(V). The exhausted HFO@PS-Cl could be refreshed for cyclic runs with insignificant capacity loss by the combined regeneration strategy, that is, alkaline solution to rinse the adsorbed As(V) and NaClO solution to renew the host oxidation capability. In addition, fixed-bed experiments demonstrated that the HFO@PS-Cl column could generate >1760 bed volume (BV) effluent from a synthetic As(III)-containing groundwater to meet the drinking water standard (nanocomposites, HFO@PS-N and HFO@D201 could only generate 450 and 600 BV effluents under otherwise identical conditions.

Summary of quantum aspects of gravitation workshop

Indian Academy of Sciences (India)

Summary of quantum aspects of gravitation workshop. GHANASHYAM DATE and JNANADEV MAHARANA. The Institute of Mathematical Sciences, CIT Campus, Taramani, Chennai 600 113, India. The Institute of Physics, Sachivalaya Marg, Bhubaneswar 751 005, India. Abstract. This is a summary of the presentations at ...

FEMA Disaster Declarations Summary

Data.gov (United States)

Department of Homeland Security — The FEMA Disaster Declarations Summary is a summarized dataset describing all federally declared disasters, starting with the first disaster declaration in 1953,...

Fusion Power Demonstration III

International Nuclear Information System (INIS)

Lee, J.D.

1985-07-01

This is the third in the series of reports covering the Fusion Power Demonstration (FPD) design study. This volume considers the FPD-III configuration that incorporates an octopole end plug. As compared with the quadrupole end-plugged designs of FPD-I and FPD-II, this octopole configuration reduces the number of end cell magnets and shortens the minimum ignition length of the central cell. The end-cell plasma length is also reduced, which in turn reduces the size and cost of the end cell magnets and shielding. As a contiuation in the series of documents covering the FPD, this report does not stand alone as a design description of FPD-III. Design details of FPD-III subsystems that do not differ significantly from those of the FPD-II configuration are not duplicated in this report

Epidermal Growth Factor Receptor Variant III (EGFRvIII) Positivity in EGFR-Amplified Glioblastomas: Prognostic Role and Comparison between Primary and Recurrent Tumors.

Science.gov (United States)

Felsberg, Jörg; Hentschel, Bettina; Kaulich, Kerstin; Gramatzki, Dorothee; Zacher, Angela; Malzkorn, Bastian; Kamp, Marcel; Sabel, Michael; Simon, Matthias; Westphal, Manfred; Schackert, Gabriele; Tonn, Jörg C; Pietsch, Torsten; von Deimling, Andreas; Loeffler, Markus; Reifenberger, Guido; Weller, Michael

2017-11-15

Purpose: Approximately 40% of all glioblastomas have amplified the EGFR gene, and about half of these tumors express the EGFRvIII variant. The prognostic role of EGFRvIII in EGFR -amplified glioblastoma patients and changes in EGFRvIII expression in recurrent versus primary glioblastomas remain controversial, but such data are highly relevant for EGFRvIII-targeted therapies. Experimental Design: EGFR -amplified glioblastomas from 106 patients were assessed for EGFRvIII positivity. Changes in EGFR amplification and EGFRvIII status from primary to recurrent glioblastomas were evaluated in 40 patients with EGFR -amplified tumors and 33 patients with EGFR -nonamplified tumors. EGFR single-nucleotide variants (SNV) were assessed in 27 patients. Data were correlated with outcome and validated in 150 glioblastoma patients from The Cancer Genome Atlas (TCGA) consortium. Results: Sixty of 106 EGFR -amplified glioblastomas were EGFRvIII-positive (56.6%). EGFRvIII positivity was not associated with different progression-free or overall survival. EGFRvIII status was unchanged at recurrence in 35 of 40 patients with EGFR -amplified primary tumors (87.5%). Four patients lost and one patient gained EGFRvIII positivity at recurrence. None of 33 EGFR- nonamplified glioblastomas acquired EGFR amplification or EGFRvIII at recurrence. EGFR SNVs were frequent in EGFR -amplified tumors, but were not linked to survival. Conclusions: EGFRvIII and EGFR SNVs are not prognostic in EGFR -amplified glioblastoma patients. EGFR amplification is retained in recurrent glioblastomas. Most EGFRvIII-positive glioblastomas maintain EGFRvIII positivity at recurrence. However, EGFRvIII expression may change in a subset of patients at recurrence, thus repeated biopsy with reassessment of EGFRvIII status is recommended for patients with recurrent glioblastoma to receive EGFRvIII-targeting agents. Clin Cancer Res; 23(22); 6846-55. ©2017 AACR . ©2017 American Association for Cancer Research.

Summary talk

International Nuclear Information System (INIS)

Johnson, R.C.

1981-01-01

In this summary talk some implications of points raised during the Daresbury Study Weekend on heavy-ion reactions are examined and discussed in particular those concerning polarized heavy ions, the connection between analyzing powers and dynamics, transfer reactions, total reaction cross section measurements with polarized beams, and the implications of break-up reaction results for theories of nuclear reactions involving loosely bound projectiles. (U.K.)

Summary talk

International Nuclear Information System (INIS)

Harari, H.

1978-10-01

A general overview is given in this high energy physics conference summary. Quantum chromodynamics as a theory of strong interactions and studied by experimental tests, SU(2) x U(1) theory of weak and electromagnetic interactions and its experimental tests, weak interactions above 100 GeV, simple unification of weak and electromagnetic interactions, and the grand and the ultimate unifications with extended supergravity are discussed. 28 references

Gd(III)-nanodiamond conjugates for MRI contrast enhancement

Science.gov (United States)

Manus, Lisa M.; Mastarone, Daniel J.; Waters, Emily A.; Zhang, Xue-Qing; Schultz-Sikma, Elise A.; MacRenaris, Keith W.; Ho, Dean

2010-01-01

A Gd(III)-nanodiamond conjugate [Gd(III)-ND] was prepared and characterized, enabling detection of nanodiamonds by MR imaging. The Gd(III)-ND particles significantly reduced the T1 of water protons with a per-Gd(III) relaxivity of 58.82 ± 1.18 mM−1s−1 at 1.5 Tesla (60 MHz). This represents a tenfold increase compared to the monomer Gd(III) complex (r1 = 5.42 ± 0.20 mM−1s−1) and is among the highest per-Gd(III) relaxivities reported. PMID:20038088

Safeguards summary event list (SSEL)

International Nuclear Information System (INIS)

1989-07-01

The Safeguards Summary Event List (SSEL) provides brief summaries of several hundred safeguards-related events involving nuclear material or facilities regulated by the US Nuclear Regulatory Commission (NRC). Because of public interest, also included are events reported involving byproduct material which is exempt from safeguards requirements. Events are described under the categories of bomb-related, intrusion, missing and/or allegedly stolen, transportation, tampering/vandalism, arson, firearms, radiological sabotage, nonradiological sabotage, alcohol and drugs, and miscellaneous. The information contained in the event descriptions is derived primarily from official NRC reporting channels

Experimental Plasma Research project summaries

International Nuclear Information System (INIS)

1980-09-01

This report contains descriptions of the activities supported by the Experimental Plasma Research Branch of APP. The individual project summaries were prepared by the principal investigators and include objectives and milestones for each project. The projects are arranged in six research categories: Plasma Properties; Plasma Heating; Plasma Diagnostics; Atomic, Molecular and Nuclear Physics; Advanced Superconducting Materials; and the Fusion Plasma Research Facility (FPRF). Each category is introduced with a statement of objectives and recent progress and followed by descriptions of individual projects. An overall budget summary is provided at the beginning of the report

Safeguards Summary Event List (SSEL)

International Nuclear Information System (INIS)

Fadden, M.; Yardumian, J.

1993-07-01

The Safeguards Summary Event List provides brief summaries of hundreds of safeguards-related events involving nuclear material or facilities regulated by the US Nuclear Regulatory Commission. Events are described under the categories: Bomb-related, Intrusion, Missing/Allegedly Stolen, Transportation-related, Tampering/Vandalism, Arson, Firearms-related, Radiological Sabotage, Non-radiological Sabotage, and Miscellaneous. Because of the public interest, the Miscellaneous category also includes events reported involving source material, byproduct material, and natural uranium, which are exempt from safeguards requirements. Information in the event descriptions was obtained from official NRC sources

Experimental Plasma Research project summaries

Energy Technology Data Exchange (ETDEWEB)

None

1980-09-01

This report contains descriptions of the activities supported by the Experimental Plasma Research Branch of APP. The individual project summaries were prepared by the principal investigators and include objectives and milestones for each project. The projects are arranged in six research categories: Plasma Properties; Plasma Heating; Plasma Diagnostics; Atomic, Molecular and Nuclear Physics; Advanced Superconducting Materials; and the Fusion Plasma Research Facility (FPRF). Each category is introduced with a statement of objectives and recent progress and followed by descriptions of individual projects. An overall budget summary is provided at the beginning of the report.

Recent methodological advances in male hormonal contraception.

Science.gov (United States)

Liu, Peter Y; Swerdloff, Ronald S; Wang, Christina

2010-11-01

Landmark WHO-sponsored trials showed decades ago that male hormonal contraception (MHC) is an effective male-directed contraceptive approach. Considerable progress has been made particularly in the last 5 years, establishing for the first time the reversibility of MHC and its short-term safety. Methodological advances in recent years include the pooling of information and individual-level integrated analysis; the first-time use of centralized semen analysis and fluorescence to detect low sperm concentrations; the establishment of sperm quality reference ranges in fertile men; the measurement of blood steroid concentrations by gas chromatography/mass spectrometry; and the inclusion of placebo groups to delineate clearly possible adverse effects of androgens and progestins in men. We report integrated analyses of factors that are important in predicting suppression and recovery of spermatogenesis after MHC clinical trials for the past 15 years. These are the best data available and will provide guidance and reassurance for the larger-scale Phase III specific regimen efficacy studies that will be required to bring MHC to the population (market). Copyright © 2010 Elsevier Inc. All rights reserved.

Thermodynamic model for solution behavior and solid-liquid equilibrium in Na-Al(III)-Fe(III)-Cr(III)-Cl-H2O system at 25°C

Science.gov (United States)

André, Laurent; Christov, Christomir; Lassin, Arnault; Azaroual, Mohamed

2018-03-01

The knowledge of the thermodynamic behavior of multicomponent aqueous electrolyte systems is of main interest in geo-, and environmental-sciences. The main objective of this study is the development of a high accuracy thermodynamic model for solution behavior, and highly soluble M(III)Cl3(s) (M= Al, Fe, Cr) minerals solubility in Na-Al(III)-Cr(III)-Fe(III)-Cl-H2O system at 25°C. Comprehensive thermodynamic models that accurately predict aluminium, chromium and iron aqueous chemistry and M(III) mineral solubilities as a function of pH, solution composition and concentration are critical for understanding many important geochemical and environmental processes involving these metals (e.g., mineral dissolution/alteration, rock formation, changes in rock permeability and fluid flow, soil formation, mass transport, toxic M(III) remediation). Such a model would also have many industrial applications (e.g., aluminium, chromium and iron production, and their corrosion, solve scaling problems in geothermal energy and oil production). Comparisons of solubility and activity calculations with the experimental data in binary and ternary systems indicate that model predictions are within the uncertainty of the data. Limitations of the model due to data insufficiencies are discussed. The solubility modeling approach, implemented to the Pitzer specific interaction equations is employed. The resulting parameterization was developed for the geochemical Pitzer formalism based PHREEQC database.

Timely management of developing class III malocclusion

Directory of Open Access Journals (Sweden)

M R Yelampalli

2012-01-01

Full Text Available Timing of orthodontic treatment, especially for children with developing class III malocclusions, has always been somewhat controversial, and definitive treatment tends to be delayed for severe class III cases. Developing class III patients with moderate to severe anterior crossbite and deep bite may need early intervention in some selected cases. Class III malocclusion may develop in children as a result of an inherent growth abnormality, i.e. true class III malocclusion, or as a result of premature occlusal contacts causing forward functional shift of the mandible, which is known as pseudo class III malocclusion. These cases, if not treated at the initial stage of development, interfere with normal growth of the jaw bases and may result in severe facial deformities. The treatment should be carried out as early as possible for permitting normal growth of the skeletal bases. This paper deals with the selection of an appropriate appliance from the various current options available for early intervention in developing class III malocclusion through two case reports.

Summary reports of activities under visiting research program (1993)

International Nuclear Information System (INIS)

1993-10-01

The summary reports of activities under visiting research program in the Research Reactor Institute, Kyoto University, in fiscal year 1992 are included. In this report, 104 summaries of researches using the Kyoto University Reactor (KUR) and 9 summaries of the researches using the Kyoto University Critical Assembly (KUCA) are collected. (J.P.N.)

Summary Report of Consultants' Meeting on Accuracy of Experimental and Theoretical Nuclear Cross-Section Data for Ion Beam Analysis and Benchmarking

International Nuclear Information System (INIS)

Abriola, Daniel; Dimitriou, Paraskevi; Gurbich, Alexander F.

2013-11-01

A summary is given of a Consultants' Meeting assembled to assess the accuracy of experimental and theoretical nuclear cross-section data for Ion Beam Analysis and the role of benchmarking experiments. The participants discussed the different approaches to assigning uncertainties to evaluated data, and presented results of benchmark experiments performed in their laboratories. They concluded that priority should be given to the validation of cross- section data by benchmark experiments, and recommended that an experts meeting be held to prepare the guidelines, methodology and work program of a future coordinated project on benchmarking.

Hybrid III-V/silicon lasers

Science.gov (United States)

Kaspar, P.; Jany, C.; Le Liepvre, A.; Accard, A.; Lamponi, M.; Make, D.; Levaufre, G.; Girard, N.; Lelarge, F.; Shen, A.; Charbonnier, P.; Mallecot, F.; Duan, G.-H.; Gentner, J.-.; Fedeli, J.-M.; Olivier, S.; Descos, A.; Ben Bakir, B.; Messaoudene, S.; Bordel, D.; Malhouitre, S.; Kopp, C.; Menezo, S.

2014-05-01

The lack of potent integrated light emitters is one of the bottlenecks that have so far hindered the silicon photonics platform from revolutionizing the communication market. Photonic circuits with integrated light sources have the potential to address a wide range of applications from short-distance data communication to long-haul optical transmission. Notably, the integration of lasers would allow saving large assembly costs and reduce the footprint of optoelectronic products by combining photonic and microelectronic functionalities on a single chip. Since silicon and germanium-based sources are still in their infancy, hybrid approaches using III-V semiconductor materials are currently pursued by several research laboratories in academia as well as in industry. In this paper we review recent developments of hybrid III-V/silicon lasers and discuss the advantages and drawbacks of several integration schemes. The integration approach followed in our laboratory makes use of wafer-bonded III-V material on structured silicon-on-insulator substrates and is based on adiabatic mode transfers between silicon and III-V waveguides. We will highlight some of the most interesting results from devices such as wavelength-tunable lasers and AWG lasers. The good performance demonstrates that an efficient mode transfer can be achieved between III-V and silicon waveguides and encourages further research efforts in this direction.

Use of Fe(III) oxalate for oxidativewastewater treatment; Einsatz von Fe(III)-Oxalat zur chemisch-oxidativen Abwasserbehandlung

Energy Technology Data Exchange (ETDEWEB)

Kim, S.M.; Vogelpohl, A. [Clausthal Univ., Clausthal-Zellerfeld (Germany). Inst. fuer Thermische Verfahrenstechnik

1998-08-01

Iron(III)-oxalate was used as an iron catalyst for the Photo Fenton reaction. Iron(III) oxalations ([Fe(C{sub 2}O{sub 4}){sub 3}]{sup 3-}) are reduced to Fe(II) by irradiation using near UV-light ({lambda} = 300 - 400 nm) or visible light ({lambda} > 400 nm). At the same time, CO{sub 2}{sup -} or C{sub 2}O{sub 4}{sup -}-radicals originate, which cause the secondary reduction of Fe(III) to Fe(II). By means of the photolytically regenerated Fe(II) ions, hydroxyl radicals are increasingly formed, so that the degradation of organic substances is accelerated. The work aimed to assess the catalytic effect of Fe(III) oxalate for photochemical oxidation processes and to establish the parameters influencing further treatment of leachate from a municipal waste sanitary landfill by means of technical-scale experiments. (orig.) [Deutsch] In der vorliegenden Arbeit wurde Eisen(III)-Oxalat als Eisenkatalysator fuer die Photo-Fenton-Reaktion eingesetzt. Eisen(III)-Oxalationen ([Fe(C{sub 2}O{sub 4}){sub 3}]{sup 3-}) werden durch Strahlung mit nahem UV-Licht ({lambda}=300 bis 400 nm) oder mit sichtbarem Licht ({lambda}>400 nm) zu Fe(II) reduziert. Gleichzeitig entstehen CO{sub 2}{sup .-} oder C{sub 2}O{sub 4}{sup .-}-Radikale, die eine sekundaere Reduktion von Fe(III) zu Fe(II) bewirken. Mit Hilfe der photolytiisch regenerierten Fe(II)-Ionen werden vermehrt Hydroxylradikale gebildet und damit die Abbaugeschwindigkeit der organischen Substanzen beschleunigt. Ziel der hier vorgestellten Arbeit war es, die katalytische Wirkung von Fe(III)-Oxalat fuer photochemische Oxidationsverfahren abzuschaetzen und die Einflussparameter zur weitergehenden Behandlung eines Deponiesickerwassers aus Hausmuelldeponie anhand von Technikumsversuchen zu ermitteln. (orig.)

AEGIS methodology and a perspective from AEGIS methodology demonstrations

International Nuclear Information System (INIS)

Dove, F.H.

1981-03-01

Objectives of AEGIS (Assessment of Effectiveness of Geologic Isolation Systems) are to develop the capabilities needed to assess the post-closure safety of waste isolation in geologic formation; demonstrate these capabilities on reference sites; apply the assessment methodology to assist the NWTS program in site selection, waste package and repository design; and perform repository site analyses for the licensing needs of NWTS. This paper summarizes the AEGIS methodology, the experience gained from methodology demonstrations, and provides an overview in the following areas: estimation of the response of a repository to perturbing geologic and hydrologic events; estimation of the transport of radionuclides from a repository to man; and assessment of uncertainties

Synthesis of Er(III)/Yb(III)-doped BiF3 upconversion nanoparticles for use in optical thermometry.

Science.gov (United States)

Du, Peng; Yu, Jae Su

2018-03-23

The authors describe an ethylene glycol assisted precipitation method for synthesis of Er(III)/Yb(III)-doped BiF 3 nanoparticles (NPs) at room temperature. Under 980-nm light irradiation, the NPs emit upconversion (UC) emission of Er(III) ions as a result of a two-photon absorption process. The temperature-dependent green emissions (peaking at 525 and 545 nm) are used to establish an unambiguous relationship between the ratio of fluorescence intensities and temperature. The NPs have a maximum sensitivity of 6.5 × 10 -3  K -1 at 619 K and can be applied over the 291-691 K temperature range. The results indicate that these NPs are a promising candidate for optical thermometry. Graphical abstract Schematic of the room-temperature preparation of Er(III)/Yb(III)-doped BiF 3 nanoparticles with strongly temperature-dependent upconversion emission.

Studies of Binary Complexes of Tripodal Ligand cis,cis-1,3,5-tris(methylaminocyclohexane with Cr(III and Fe(III

Directory of Open Access Journals (Sweden)

S. Esakki Muthu

2005-01-01

Full Text Available The formation of binary complexes of Cr(III and Fe(III with a tripodal ligand cis,cis-1,3,5-tris(methylaminocyclohexane (tmach (L has been investigated in solution. The overall stability constants of tmach with Cr(III and Fe(III were determined by potentiometric method at an ionic strength of 0.1 M NaClO4 at 25±1°C in aqueous medium. The formation of species like MLH25+, MLH4+, ML3+, ML(OH2+ and ML(OH3 were observed. Fe(III was found to form more stable complexes than Cr(III. Molecular mechanics calculations were performed to explain the mode of coordination in solution.

Mechanisms for Fe(III) oxide reduction in sedimentary environments

Science.gov (United States)

Nevin, Kelly P.; Lovely, Derek R.

2002-01-01

Although it was previously considered that Fe(III)-reducing microorganisms must come into direct contact with Fe(III) oxides in order to reduce them, recent studies have suggested that electron-shuttling compounds and/or Fe(III) chelators, either naturally present or produced by the Fe(III)-reducing microorganisms themselves, may alleviate the need for the Fe(III) reducers to establish direct contact with Fe(III) oxides. Studies with Shewanella alga strain BrY and Fe(III) oxides sequestered within microporous beads demonstrated for the first time that this organism releases a compound(s) that permits electron transfer to Fe(III) oxides which the organism cannot directly contact. Furthermore, as much as 450 w M dissolved Fe(III) was detected in cultures of S. alga growing in Fe(III) oxide medium, suggesting that this organism releases compounds that can solublize Fe(III) from Fe(III) oxide. These results contrast with previous studies, which demonstrated that Geobacter metallireducens does not produce electron-shuttles or Fe(III) chelators. Some freshwater aquatic sediments and groundwaters contained compounds, which could act as electron shuttles by accepting electrons from G. metallireducens and then transferring the electrons to Fe(III). However, other samples lacked significant electron-shuttling capacity. Spectroscopic studies indicated that the electron-shuttling capacity of the waters was not only associated with the presence of humic substances, but water extracts of walnut, oak, and maple leaves contained electron-shuttling compounds did not appear to be humic substances. Porewater from a freshwater aquatic sediment and groundwater from a petroleum-contaminated aquifer contained dissolved Fe(III) (4-16 w M), suggesting that soluble Fe(III) may be available as an electron acceptor in some sedimentary environments. These results demonstrate that in order to accurately model the mechanisms for Fe(III) reduction in sedimentary environments it will be necessary