Experimental study for development of thermic lance cutting method

International Nuclear Information System (INIS)

Machida, N.; Katano, Y.; Kamiya, Y.

1988-01-01

A series of experiments on a thermic lance cutting method were carried out to obtain useful data for the practical application of this method to the dismantling of reinforced concrete. As a first step, a performance experiment was executed to study basic cutting performance relating to oxygen consumption, extent of bar loss and cutting speed, as well as by-products generated during cutting work such as powdered dust, gas, fumes and slag. An automated and remote-controlled cutting machine was then developed utilizing automated bar supply and ignition. This paper describes the result of these experiments. (author)

Grading technologies for the manufacture of innovative cutting blades

Science.gov (United States)

Rostek, Tim; Homberg, Werner

2018-05-01

Cutting blades for harvesting applications are used in a variety of agricultural machines. These parts are in contact with highly abrasive lawn clippings and often wear out within hours which results in high expensive re-sharpening maintenance. This paper relates to manufacturing techniques enhancing the durability of cutting blades based on a structural analysis of the prevailing wear mechanisms containing chipping and abrasive wear. Each mechanism results in specific demands on the cutting edge's mechanical characteristics. The design of evaluation methods respectively is one issue of the paper. This is basis for approaches to improve the cutting edge performance on purpose. On option to improve abrasive wear resistance and, thus, service life is the application of locally graded steel materials as semi-finished products for self-sharpening cutting blades. These materials comprise a layered structure consisting of a hard, wear resistant layer and a relatively softer layer which is lesser wear resistant. As the cutting blade is subjected to wear conditions, the less wear resistant layer wears faster than the relatively more wear resistant harder layer revealing a durable cross section of the cutting edge and, thus, cutting performance. Anyways, chipping is another key issue on the cutting edge's lifetime. Here, the cutting edges cross section by means of geometry and grind respectively as well as its mechanical properties matter. FEM analysis reveal innovative options to optimize the cross section of the blade as well as thermomechanical strengthening add further strength to reduce chipping. This paper contains a comprehensive strategy to improve cutting blades with use of innovative manufacturing technologies which apply application-specific graded mechanical characteristics and, thus, significantly improved performance characteristics.

Development of contaminated concrete removing system 'Clean cut method'

International Nuclear Information System (INIS)

Kinoshita, Takehiko; Tanaka, Tsutomu; Funakawa, Naoyoshi; Idemura, Hajime; Sakashita, Fumio; Tajitsu, Yoshiteru

1989-01-01

In the case of decommissioning nuclear facilities such as nuclear power stations, nuclear fuel facilities and RI handling facilities and carrying out reconstruction works, if there is radioactive contamination on the surfaces of concrete structures such as the floors and walls of the buildings for nuclear facilities, it must be removed. Since concrete is porous, contamination infiltrates into the inside of concrete, and the wiping of surfaces only or chemical decontamination cannot remove it, therefore in most cases, contaminated concrete must be removed. The removal of concrete surfaces has been carried out with chipping hammers, grinders and so on, but many problems arise due to it. In order to solve these problems, the mechanical cutting method was newly devised, and clean cut method (CCRS) was completed. The depth of cutting from concrete surface is set beforehand, and the part to be removed is accurately cut, at the same time, the concrete powder generated is collected nearly perfectly, and recovered into a drum. The outline of the method and the constitution of the system, the features of the clean cut method, the development of the technology for cutting concrete and the technology for recovering concrete powder, and the test of verifying decontamination are reported. (K.I.)

Twice cutting method reduces tibial cutting error in unicompartmental knee arthroplasty.

Science.gov (United States)

Inui, Hiroshi; Taketomi, Shuji; Yamagami, Ryota; Sanada, Takaki; Tanaka, Sakae

2016-01-01

Bone cutting error can be one of the causes of malalignment in unicompartmental knee arthroplasty (UKA). The amount of cutting error in total knee arthroplasty has been reported. However, none have investigated cutting error in UKA. The purpose of this study was to reveal the amount of cutting error in UKA when open cutting guide was used and clarify whether cutting the tibia horizontally twice using the same cutting guide reduced the cutting errors in UKA. We measured the alignment of the tibial cutting guides, the first-cut cutting surfaces and the second cut cutting surfaces using the navigation system in 50 UKAs. Cutting error was defined as the angular difference between the cutting guide and cutting surface. The mean absolute first-cut cutting error was 1.9° (1.1° varus) in the coronal plane and 1.1° (0.6° anterior slope) in the sagittal plane, whereas the mean absolute second-cut cutting error was 1.1° (0.6° varus) in the coronal plane and 1.1° (0.4° anterior slope) in the sagittal plane. Cutting the tibia horizontally twice reduced the cutting errors in the coronal plane significantly (Pcutting the tibia horizontally twice using the same cutting guide reduced cutting error in the coronal plane. Copyright © 2014 Elsevier B.V. All rights reserved.

Insulin resistance in obese children and adolescents: HOMA-IR cut-off levels in the prepubertal and pubertal periods.

Science.gov (United States)

Kurtoğlu, Selim; Hatipoğlu, Nihal; Mazıcıoğlu, Mümtaz; Kendirici, Mustafa; Keskin, Mehmet; Kondolot, Meda

2010-01-01

Childhood obesity is associated with an increased risk for insulin resistance. The underlying mechanism for the physiological increase in insulin levels in puberty is not clearly understood. The aim of the present study was to determine the cut-off values for homeostasis model assessment for insulin resistance (HOMA-IR) in obese children and adolescents according to gender and pubertal status. Two hundred and eight obese children and adolescents (141 girls, 127 boys) aged between 5 and 18 years were included in the study. The children were divided into prepubertal and pubertal groups. A standard oral glucose tolerance test (OGTT) was carried out in all children. A total insulin level exceeding 300 μU/mL in the blood samples, collected during the test period, was taken as the insulin resistance criterion. Cut-off values for HOMA-IR were calculated by receiver operating characteristic (ROC) analysis. In the prepubertal period, the rate of insulin resistance was found to be 37% in boys and 27.8% in girls,while in the pubertal period, this rate was 61.7% in boys and 66.7% in girls. HOMA-IR cut-off values for insulin resistance in the prepubertal period were calculated to be 2.67 (sensitivity 88.2%, specificity 65.5%) in boys and 2.22 (sensitivity 100%, specificity 42.3%) in girls, and in the pubertal period, they were 5.22 (sensitivity 56%, specificity 93.3%) in boys and 3.82 (sensitivity 77.1%, specificity 71.4%) in girls. Since gender, obesity and pubertal status are factors affecting insulin resistance, cut-off values which depend on gender and pubertal status, should be used in evaluation of insulin resistance.

HIGH PERFORMANCE TAPS FOR CUTTING THREADS IN DIFFICULT TO MACHINE MATERIALS

Directory of Open Access Journals (Sweden)

M. R. Akhmedova

2016-01-01

Full Text Available Objectives. This article explores in detail questions of instrument operation function of tapping internal threads in hard materials. The existing relationship between vibration system amplitude and tool durability is indicated; on this basis, it is determined that the best course for improving the durability performance is increasing vibratory resistance. Based on a critical analysis of existing designs with consideration of their flaws, the development of new technological designs of taps is tasked with ensuring stable operation when handling hard materials. Methods. It is noteworthy that one of the main vibration resistance improvement methods of the tool is to reduce the contact area of the tool with the work piece in the cutting zone. Methods are proposed for improving the vibration resistance of taps, considering the correlation adjustment of tap teeth in order to completely eliminate friction at the sides of the thread cutting surface and uneven implementation flute cutting steps. Results. The idea of increasing vibration resistance has seen the new development of vibration-proof tap designs, heralded as innovations due to the accuracy of thread cutting and durability achieved by reducing the thread contact area with the work piece in the cutting zone. Increased vibration resistance is achieved in the modified taps through high correction by means of thread side downgrading of the coarse tap cone by an additional angle of 30º. In another design, the stylus provided with uneven angular spacing. Test results of designed taps machined in corrosion-resistant 1Kh18N9T steel. A manifold increase in tool durability was achieved due to its high vibration resistance. Conclusions. The redesigned taps have a number of advantages, characterised by a high resistance when processing difficult materials and an insignificant increase in the complexity of their manufacture compared with standard taps. Therefore they can be recommended for large

Cut Based Method for Comparing Complex Networks.

Science.gov (United States)

Liu, Qun; Dong, Zhishan; Wang, En

2018-03-23

Revealing the underlying similarity of various complex networks has become both a popular and interdisciplinary topic, with a plethora of relevant application domains. The essence of the similarity here is that network features of the same network type are highly similar, while the features of different kinds of networks present low similarity. In this paper, we introduce and explore a new method for comparing various complex networks based on the cut distance. We show correspondence between the cut distance and the similarity of two networks. This correspondence allows us to consider a broad range of complex networks and explicitly compare various networks with high accuracy. Various machine learning technologies such as genetic algorithms, nearest neighbor classification, and model selection are employed during the comparison process. Our cut method is shown to be suited for comparisons of undirected networks and directed networks, as well as weighted networks. In the model selection process, the results demonstrate that our approach outperforms other state-of-the-art methods with respect to accuracy.

Selection of Near Optimal Laser Cutting Parameters in CO2 Laser Cutting by the Taguchi Method

Directory of Open Access Journals (Sweden)

Miloš MADIĆ

2013-12-01

Full Text Available Identification of laser cutting conditions that are insensitive to parameter variations and noise is of great importance. This paper demonstrates the application of Taguchi method for optimization of surface roughness in CO2 laser cutting of stainless steel. The laser cutting experiment was planned and conducted according to the Taguchi’s experimental design using the L27 orthogonal array. Four laser cutting parameters such as laser power, cutting speed, assist gas pressure, and focus position were considered in the experiment. Using the analysis of means and analysis of variance, the significant laser cutting parameters were identified, and subsequently the optimal combination of laser cutting parameter levels was determined. The results showed that the cutting speed is the most significant parameter affecting the surface roughness whereas the influence of the assist gas pressure can be neglected. It was observed, however, that interaction effects have predominant influence over the main effects on the surface roughness.

A review of virtual cutting methods and technology in deformable objects.

Science.gov (United States)

Wang, Monan; Ma, Yuzheng

2018-06-05

Virtual cutting of deformable objects has been a research topic for more than a decade and has been used in many areas, especially in surgery simulation. We refer to the relevant literature and briefly describe the related research. The virtual cutting method is introduced, and we discuss the benefits and limitations of these methods and explore possible research directions. Virtual cutting is a category of object deformation. It needs to represent the deformation of models in real time as accurately, robustly and efficiently as possible. To accurately represent models, the method must be able to: (1) model objects with different material properties; (2) handle collision detection and collision response; and (3) update the geometry and topology of the deformable model that is caused by cutting. Virtual cutting is widely used in surgery simulation, and research of the cutting method is important to the development of surgery simulation. Copyright © 2018 John Wiley & Sons, Ltd.

Mechanical fragmentation of nuclear reactor fuel assemblies by the double cutting method

International Nuclear Information System (INIS)

Voitsekhovskii, B.V.; Istomin, V.L.; Mitrofanov, V.V.

1995-01-01

A method is described for cutting a spent fuel assembly with straight shears into pieces of a prescribed size. The method does not require separation of the casing and the lattices. The double cutting method is briefly described, and experiments designed for cutting BN-350 and VVER-440 fuel assemblies are outlined. The testing showed that the cutting method was suitable for mechanical polarization of fuel assemblies. The investigations led to the development of turnkey industrial equipment for cutting spent fuel assemblies of different geometries with a maximum size up to 170 mm. 6 refs., 8 figs., 1 tab

Making the cut for the contour method

OpenAIRE

Bouchard, P. John; Ledgard, Peter; Hiller, Stan; Hosseinzadh Torknezhad, Foroogh

2012-01-01

The contour method is becoming an increasingly popular measurement technique for mapping residual stress in engineering components. The accuracy of the technique is critically dependent on the quality of the cut performed. This paper presents results from blind cutting trials on austenitic stainless steel using electro-discharge machines made by three manufacturers. The suitability of the machines is assessed based on the surface finish achieved, risk of wire breakages and the nature of cutti...

A Study of Selected Properties and Applications of AlMgB₁₄ and Related Composites: Ultra-Hard Materials

Energy Technology Data Exchange (ETDEWEB)

Lewis, Theron L. [Iowa State Univ., Ames, IA (United States)

2001-01-01

This research presents a study of the hardness, electrical, and thermal properties AlMgB₁₄ containing Al₂MgO₄ spinel. This research also investigated how much Al₂MgO₄ spinel consistently forms with AlMgB₁₄, if AlMgB₁₄ materials can be produced by hot isostatic pressing (HIP), what effects TiC and TiB₂ have on this composite material, and the importance of mechanical alloying. Included also is a study of the variation in hardness measurements and how they relate to SI units. Heretofore, all ultra-hard materials (hardness > 40 GPA) have been found to be cubic in structure, electrical insulators, and expensive; the behavior of AlMgB₁₄, which in certain specimens and compositions can have hardness values greater than 40 GPa, is therefore quite unusual since it is non-cubic, conductive, and moderate in cost. This offers an opportunity to investigate the relationship between hardness, thermal, and electrical properties from a new perspective. The main purpose of this project was to characterize the different properties of the AlMgB₁₄ materials and to demonstrate that this material can be made in bulk. The technologies used for this study include microhardness measurement techniques, scanning electron microscopy, energy dispersive spectroscopy, x-ray diffraction spectroscopy, x-ray diffraction spectroscopy at different temperatures, optical microscopy, thermomechanical analysis, differential thermal analysis, 4-point probe resistivity, density techniques, Seebeck Effect, and Hall Effect. This research may lead to use of this material for applications where high abrasion resistance along with electrical conduction is needed. Also this research gave more information about a material that could have a great impact on industrial applications.

Using internally cooled cutting tools in the machining of difficult-to-cut materials based on Waspaloy

Directory of Open Access Journals (Sweden)

Yahya Isik

2016-05-01

Full Text Available Nickel-based superalloys such as Waspaloy are used for engine components and in the nuclear industry, where considerable strength and corrosion resistance at high operating temperatures are called for. These characteristics of such alloys cause increases in cutting temperature and resultant tool damage, even at low cutting speeds and low feed rates. Thus, they are classified as difficult-to-cut materials. This article presents a cooling method to be used in metal cutting based on a tool holder with a closed internal cooling system with cooling fluid circulating inside. Hence, a green cooling method that does not harm the environment and is efficient in removing heat from the cutting zone was developed. A series of cutting experiments were conducted to investigate the practicality and effectiveness of the internally cooled tool model. The developed system achieved up to 13% better surface quality than with dry machining, and tool life was extended by 12%. The results clearly showed that with the reduced cutting temperature of the internal cooling, it was possible to control the temperature and thus prevent reaching the critical cutting temperature during the turning process, which is vitally important in extending tool life during the processing of Waspaloy.

Cutting-balloon angioplasty of resistant ureteral stenosis as bridge to stent insertion

Energy Technology Data Exchange (ETDEWEB)

Iezzi, R., E-mail: iezzir@virgilio.it [Department of Bioimaging and Radiological Sciences, Institute of Radiology, ' A. Gemelli' Hospital - Catholic University, L.go A Gemelli 8, 00168 Rome (Italy); Di Stasi, C.; Simeone, A.; Bonomo, L. [Department of Bioimaging and Radiological Sciences, Institute of Radiology, ' A. Gemelli' Hospital - Catholic University, L.go A Gemelli 8, 00168 Rome (Italy)

2011-07-15

Ureteral stenting is a routine, minimally invasive procedure performed for relief of benign or malignant obstruction. In case of ureteral stenosis, to allow a correct insertion of the stent, a predilatation of the ureter stenosis with a conventional balloon catheter can be necessary. In exceptional cases, it can be difficult to advance an 7-8 Fr JJ-catheter over a tight resistant ureter stenosis following unsuccessful high-pressure balloon dilatation. In the present report, we describe two cases of resistant ureter stenosis successfully dilated by a cutting-balloon following the failure of high-pressure balloon dilatation, allowing a correct and uncomplicated antegrade stent insertion.

Cutting-balloon angioplasty of resistant ureteral stenosis as bridge to stent insertion

International Nuclear Information System (INIS)

Iezzi, R.; Di Stasi, C.; Simeone, A.; Bonomo, L.

2011-01-01

Ureteral stenting is a routine, minimally invasive procedure performed for relief of benign or malignant obstruction. In case of ureteral stenosis, to allow a correct insertion of the stent, a predilatation of the ureter stenosis with a conventional balloon catheter can be necessary. In exceptional cases, it can be difficult to advance an 7-8 Fr JJ-catheter over a tight resistant ureter stenosis following unsuccessful high-pressure balloon dilatation. In the present report, we describe two cases of resistant ureter stenosis successfully dilated by a cutting-balloon following the failure of high-pressure balloon dilatation, allowing a correct and uncomplicated antegrade stent insertion.

Mathematical simulation and optimization of cutting mode in turning of workpieces made of nickel-based heat-resistant alloy

Science.gov (United States)

Bogoljubova, M. N.; Afonasov, A. I.; Kozlov, B. N.; Shavdurov, D. E.

2018-05-01

A predictive simulation technique of optimal cutting modes in the turning of workpieces made of nickel-based heat-resistant alloys, different from the well-known ones, is proposed. The impact of various factors on the cutting process with the purpose of determining optimal parameters of machining in concordance with certain effectiveness criteria is analyzed in the paper. A mathematical model of optimization, algorithms and computer programmes, visual graphical forms reflecting dependences of the effectiveness criteria – productivity, net cost, and tool life on parameters of the technological process - have been worked out. A nonlinear model for multidimensional functions, “solution of the equation with multiple unknowns”, “a coordinate descent method” and heuristic algorithms are accepted to solve the problem of optimization of cutting mode parameters. Research shows that in machining of workpieces made from heat-resistant alloy AISI N07263, the highest possible productivity will be achieved with the following parameters: cutting speed v = 22.1 m/min., feed rate s=0.26 mm/rev; tool life T = 18 min.; net cost – 2.45 per hour.

Resistivity measurements using a direct current induction method (1963)

International Nuclear Information System (INIS)

Delaplace, J.; Hillairet, J.

1964-01-01

The conventional methods for measuring electrical resistivities necessitate the fixing of electrical contacts on the sample either mechanically or by soldering. Furthermore it is also necessary to carry,out the measurements on low cross-section samples which are not always easy to obtain. Our direct-current induction method on the other hand requires no contacts and can easily be applied to samples of large cross-section. The sample is placed in a uniform magnetic field; at the moment when the current is cut, eddy currents appear in the sample which tend to oppose the disappearance of the field. The way in which the magnetic flux decreases in the sample makes it possible to determine the resistivity of the material. This method has been applied to samples having diameters of between 1 and 30 mm in the case of metals which are good conductors. It gives a value for the local resistivity and makes it possible to detect any variation along a sample. The measurements can be carried out at all temperature from a few degrees absolute to 500 deg. C. We have used the induction method to follow the purification of beryllium by zone-melting; it is in effect possible to estimate the purity of a material by resistivity measurements. We have measured the resistivity along each bar treated by the zone-melting technique and have thus, localised the purest section. High temperature measurements have been carried out on uranium carbide and on iron-aluminium alloys. This method constitutes an interesting means of investigation the resistivity of solid materials. Its accuracy and rapidity make it particularly adapted both to fundamental research and to production control. (authors) [fr

Cutting method and cutting device for spent fuel rod of nuclear reactor

International Nuclear Information System (INIS)

Komatsu, Masahiko; Ose, Toshihiko.

1996-01-01

A control rod transferred under water in a vertically suspended state is postured horizontally at such a water depth that radiations can be shielded, and then it is cut to a dropping speed limiting portion and a cross-like main body. The separated cross-like main body portion is further cut in the longitudinal direction and separated into a pair of cut pieces each having an L-shaped cross section. A disk like metal saw is used as a cutting tool. Alternatively, a plasma jet cutter or a melting-type water jet cutter is used as a cutting tool. Then, since the spent control rod to be cut is postured horizontally under water, the water depth for the cutting position can be reduced. As a result, the cutting state using the cutting tool can be observed by naked eyes from the position above the water surface thereby enabling to perform the cutting operation reliably. (N.H.)

Cutting method and device underwater

International Nuclear Information System (INIS)

Takano, Genta; Kamei, Hiromasa; Beppu, Seiji

1998-01-01

A place of material to be cut is surrounded by an openable/closable box. The material to be cut is cut underwater, and materials generated in this case are removed from the cut portion by a pressurized water jet. The removed materials are sucked and recovered together with water in the box. Among the materials caused by the cutting underwater, solid materials not floating on water are caused to stay in the midway of a sucking and recovering channel. A large sucking force might be required for the entire region of the sucking and recovering channel when sucking and recovering large sized solid materials not floating on water, but even large sized materials can be recovered easily according to the present invention since they are recovered after being sucked and stayed in the midway of the sucking and recovering channel. (N.H.)

Dictionary: Welding, cutting and allied processes. Pt. 2

International Nuclear Information System (INIS)

Kleiber, A.W.

1987-01-01

The dictionary contains approximately 40 000 entries covering all aspects of welding technology. It is based on the evaluation of numerous English, American and German sources. This comprehensive and up to date dictionary will be a reliable and helpful aid in evaluation and translating. The dictionary covers the following areas: Welding: gas welding, arc welding, gas shielded welding, resistance welding, welding of plastics, special welding processes; Cutting: flame cutting, arc cutting and special thermal cutting processes; Soldering: brazing and soldering; Other topics: thermal spraying, metal to metal adhesion, welding filler materials and other consumables, test methods, plant and equipment, accessories, automation, welding trade, general welding terminology. (orig./HP) [de

Vision-based method for tracking meat cuts in slaughterhouses

DEFF Research Database (Denmark)

Larsen, Anders Boesen Lindbo; Hviid, Marchen Sonja; Engbo Jørgensen, Mikkel

2014-01-01

Meat traceability is important for linking process and quality parameters from the individual meat cuts back to the production data from the farmer that produced the animal. Current tracking systems rely on physical tagging, which is too intrusive for individual meat cuts in a slaughterhouse envi...... (hanging, rough treatment and incorrect trimming) and our method is able to handle these perturbations gracefully. This study shows that the suggested vision-based approach to tracking is a promising alternative to the more intrusive methods currently available....

METHODS FOR INOCULATION WITH Fusarium guttiforme AND GENETIC RESISTANCE OF PINEAPPLE ( Ananas comosus var. comosus )

OpenAIRE

WANDREILLA MOREIRA GARCIA; WILLIAN KRAUSE; DEJÂNIA VIEIRA DE ARAÚJO; ISANE VERA KARSBURG; RIVANILDO DALLACORT

2017-01-01

The objective of this work was to evaluate Fusarium guttiforme inoculation methods and genetic resistance of pineapple accessions. Thus, three experiments were conducted: pathogen inoculation of different leaf types ( B, D and F ) of pineapple (1), pathogen inoculation of pineapple cuttings and detached D leaves (2), and identification of resistance to fusariosis in 19 pineapple accessions (3) sampled in the State of Mato Grosso, Brazil. The cultivars Pérola (susceptible...

Distinguishing butchery cut marks from crocodile bite marks through machine learning methods.

Science.gov (United States)

Domínguez-Rodrigo, Manuel; Baquedano, Enrique

2018-04-10

All models of evolution of human behaviour depend on the correct identification and interpretation of bone surface modifications (BSM) on archaeofaunal assemblages. Crucial evolutionary features, such as the origin of stone tool use, meat-eating, food-sharing, cooperation and sociality can only be addressed through confident identification and interpretation of BSM, and more specifically, cut marks. Recently, it has been argued that linear marks with the same properties as cut marks can be created by crocodiles, thereby questioning whether secure cut mark identifications can be made in the Early Pleistocene fossil record. Powerful classification methods based on multivariate statistics and machine learning (ML) algorithms have previously successfully discriminated cut marks from most other potentially confounding BSM. However, crocodile-made marks were marginal to or played no role in these comparative analyses. Here, for the first time, we apply state-of-the-art ML methods on crocodile linear BSM and experimental butchery cut marks, showing that the combination of multivariate taphonomy and ML methods provides accurate identification of BSM, including cut and crocodile bite marks. This enables empirically-supported hominin behavioural modelling, provided that these methods are applied to fossil assemblages.

Definition of new cut-offs of BMI and waist circumference based on body composition and insulin resistance: differences between children, adolescents and adults.

Science.gov (United States)

Hübers, M; Pourhassan, M; Braun, W; Geisler, C; Müller, M J

2017-09-01

This study aims to determine associations between anthropometric traits, regional fat depots and insulin resistance in children, adolescents and adults to define new cut-offs of body mass index (BMI) or waist circumference (WC). Cross-sectional data were assessed in 433 children, adolescents and adults (aged: 6-60 years, BMI: 23.6 [21.0-27.7] kg m -2 ). Total adipose tissue (TAT), regional subcutaneous adipose tissue (SAT total , SAT trunk ) and visceral adipose tissue (VAT) were determined by whole-body magnetic resonance imaging, fat mass by air-displacement plethysmography. Insulin resistance was evaluated by homeostasis model assessment of insulin resistance (HOMA-IR). Bivariate as well as partial correlations and regression analyses were used. Cut-off values of BMI and WC related to regional fat depots and HOMA-IR were analysed by receiver operating characteristics curve. In adults, TAT, SAT total and SAT trunk increased linearly with increasing BMI and WC, whereas they followed a cubic function in children and adolescents with a steep increase at BMI and WC ≥1 standard deviation score and VAT at WC ≥2 standard deviation score. Sex differences were apparent in adults with women having higher masses of TAT and SAT and men having higher VAT. Using established BMI or WC cut-offs, correspondent masses of TAT, SAT total , SAT trunk and VAT increased from childhood to adulthood. In all age groups, there were positive associations between BMI, WC, SAT trunk , VAT and HOMA-IR. When compared with normative cut-offs of BMI or WC, HOMA-IR-derived cut-offs of regional fat depots were lower in all age groups. Associations between BMI, WC and regional fat depots varied between children, adolescents, young and older adults. When compared with BMI-derived and WC-derived values, an insulin resistance-derived cut-off corresponded to lower masses of regional fat depots. Thus, established BMI and WC cut-offs are not appropriate to assess metabolic disturbances associated

Cutting-edge statistical methods for a life-course approach.

Science.gov (United States)

Bub, Kristen L; Ferretti, Larissa K

2014-01-01

Advances in research methods, data collection and record keeping, and statistical software have substantially increased our ability to conduct rigorous research across the lifespan. In this article, we review a set of cutting-edge statistical methods that life-course researchers can use to rigorously address their research questions. For each technique, we describe the method, highlight the benefits and unique attributes of the strategy, offer a step-by-step guide on how to conduct the analysis, and illustrate the technique using data from the National Institute of Child Health and Human Development Study of Early Child Care and Youth Development. In addition, we recommend a set of technical and empirical readings for each technique. Our goal was not to address a substantive question of interest but instead to provide life-course researchers with a useful reference guide to cutting-edge statistical methods.

Ann modeling of kerf transfer in Co2 laser cutting and optimization of cutting parameters using monte carlo method

Directory of Open Access Journals (Sweden)

Miloš Madić

2015-01-01

Full Text Available In this paper, an attempt has been made to develop a mathematical model in order to study the relationship between laser cutting parameters such as laser power, cutting speed, assist gas pressure and focus position, and kerf taper angle obtained in CO2 laser cutting of AISI 304 stainless steel. To this aim, a single hidden layer artificial neural network (ANN trained with gradient descent with momentum algorithm was used. To obtain an experimental database for the ANN training, laser cutting experiment was planned as per Taguchi’s L27 orthogonal array with three levels for each of the cutting parameters. Statistically assessed as adequate, ANN model was then used to investigate the effect of the laser cutting parameters on the kerf taper angle by generating 2D and 3D plots. It was observed that the kerf taper angle was highly sensitive to the selected laser cutting parameters, as well as their interactions. In addition to modeling, by applying the Monte Carlo method on the developed kerf taper angle ANN model, the near optimal laser cutting parameter settings, which minimize kerf taper angle, were determined.

Systems and Methods for Determining Water-Cut of a Fluid Mixture

KAUST Repository

Karimi, Muhammad Akram; Shamim, Atif; Arsalan, Muhammad

2017-01-01

Provided in some embodiments are systems and methods for measuring the water content (or water-cut) of a fluid mixture. Provided in some embodiments is a water-cut sensor system that includes a helical T-resonator, a helical ground conductor, and a

Systems and Methods for Determining Water-Cut of a Fluid Mixture

KAUST Repository

Karimi, Muhammad Akram; Shamim, Atif; Arsalan, Muhammad

2017-01-01

Provided in some embodiments are systems and methods for measuring the water content (or water-cut) of a fluid mixture. Provided in some embodiments is a water-cut sensor system that includes a T-resonator, a ground conductor, and a separator. The T

An Investigation of Undefined Cut Scores with the Hofstee Standard-Setting Method

Science.gov (United States)

Wyse, Adam E.; Babcock, Ben

2017-01-01

This article provides an overview of the Hofstee standard-setting method and illustrates several situations where the Hofstee method will produce undefined cut scores. The situations where the cut scores will be undefined involve cases where the line segment derived from the Hofstee ratings does not intersect the score distribution curve based on…

Operation of the AM-50 cutting head under different cutting conditions

Energy Technology Data Exchange (ETDEWEB)

Sikora, W; Kusz, F; Fels, M

1988-02-01

Presents results of investigations into operation of the AM-50 heading machine. About 50% of headings, i.e. about 800 km/a, are driven by about 400 heading machines. It has been found that energy consumption depends on compression strength of rock and is 6 times higher for sandstone than for clayey shale. Power consumed by cutting heads depends mainly on the web used (30-150 mm depending on rock strength). Wear of cutting tools is 1-30 pieces per meter of heading advance at a working cross-section area of 15 m/sup 2/. The AM-50 machine uses cutting speeds of 1.1-3.5 m/s. Higher speeds negatively affect the resistance to cutting. Nonuniform tool wear on the cutting head circumference is an indication of improper head design that requires remedying.

Determination of laser cutting process conditions using the preference selection index method

Science.gov (United States)

Madić, Miloš; Antucheviciene, Jurgita; Radovanović, Miroslav; Petković, Dušan

2017-03-01

Determination of adequate parameter settings for improvement of multiple quality and productivity characteristics at the same time is of great practical importance in laser cutting. This paper discusses the application of the preference selection index (PSI) method for discrete optimization of the CO2 laser cutting of stainless steel. The main motivation for application of the PSI method is that it represents an almost unexplored multi-criteria decision making (MCDM) method, and moreover, this method does not require assessment of the considered criteria relative significances. After reviewing and comparing the existing approaches for determination of laser cutting parameter settings, the application of the PSI method was explained in detail. Experiment realization was conducted by using Taguchi's L27 orthogonal array. Roughness of the cut surface, heat affected zone (HAZ), kerf width and material removal rate (MRR) were considered as optimization criteria. The proposed methodology is found to be very useful in real manufacturing environment since it involves simple calculations which are easy to understand and implement. However, while applying the PSI method it was observed that it can not be useful in situations where there exist a large number of alternatives which have attribute values (performances) very close to those which are preferred.

Wear resistance and electronic structure of cutting tool materials on a basis carbides of tungsten and titanium

International Nuclear Information System (INIS)

Ryzhkin, A.A.; Ilyasov, V.V.; Lyulko, A.V.

2001-01-01

The tool materials durability problem, in particular shock and wear resistance, has allowed to formulate a set of requirements and also to stablish the dependence between physical properties and wear. However, for understanding the nature of the process, for example determining the tribological property of the cutting tool, it is necessary to consider the atom interactions in a crystal. A theoretical study of the physical properties of cutting tool materials (W-Ti-C) with varying concentration of titanium is presented. Total and partial local electronic density for each atom in such hard solutions were calculated. (nevyjel)

Integration of Small-Diameter Wood Harvesting in Early Thinnings using the Two pile Cutting Method

Energy Technology Data Exchange (ETDEWEB)

Kaerhae, Kalle (Metsaeteho Oy, P.O. Box 101, FI-00171 Helsinki (Finland))

2008-10-15

Metsaeteho Oy studied the integrated harvesting of industrial roundwood (pulpwood) and energy wood based on a two-pile cutting method, i.e. pulpwood and energy wood fractions are stacked into two separate piles when cutting a first-thinning stand. The productivity and cost levels of the integrated, two-pile cutting method were determined, and the harvesting costs of the two-pile method were compared with those of conventional separate wood harvesting methods. In the time study, when the size of removal was 50 dm3, the productivity in conventional whole-tree cutting was 6% higher than in integrated cutting. With a stem size of 100 dm3, the productivity in whole-tree cutting was 7% higher than in integrated cutting. The results indicated, however, that integrated harvesting based on the two-pile method enables harvesting costs to be decreased to below the current cost level of separate pulpwood harvesting in first thinning stands. The greatest cost-saving potential lies in small-sized first thinnings. The results showed that, when integrated wood harvesting based on the two-pile method is applied, the removals of both energy wood and pulpwood should be more than 15-20 m3/ha at the harvesting sites in order to achieve economically viable integrated procurement

Cutting method for structural component into block like shape, and device used for cutting

International Nuclear Information System (INIS)

Nakazawa, Koichi; Ito, Akira; Tateiwa, Masaaki.

1995-01-01

Two grooves each of a predetermined depth are formed along a surface of a structural component, and a portion between the two grooves is cut in the direction of the depth from the surface of the structural component by using a cutting wire of a wire saw device. Then, the cutting wire is moved in the extending direction of the grooves while optionally changing the position in the direction of the depth to conduct cutting for the back face. Further, the cutting wire is moved in the direction of the depth of the groove toward the surface, to cut a portion between the two grooves. The wire saw device comprises a wire saw main body movable along the surface of the structural component, a pair of wire guide portions extending in the direction of the depth, guide pooleys capable of guiding the cutting wire guides revolvably and rotatably disposed at the top end, and an endless annular cutting wire extending between the wire guide portions. Thus, it is possible to continuously cut out blocks set to optional size and thickness. In addition, remote cutting is possible with no requirement for an operator to access to the vicinity of radioactivated portions. (N.H.)

Cutting Method of the CAD model of the Nuclear facility for Dismantling Simulation

Energy Technology Data Exchange (ETDEWEB)

Kim, Ikjune; Choi, ByungSeon; Hyun, Dongjun; Jeong, KwanSeong; Kim, GeunHo; Lee, Jonghwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

Current methods for process simulation cannot simulate the cutting operation flexibly. As is, to simulate a cutting operation, user needs to prepare the result models of cutting operation based on pre-define cutting path, depth and thickness with respect to a dismantle scenario in advance. And those preparations should be built again as scenario changes. To be, user can change parameters and scenarios dynamically within a simulation configuration process so that the user saves time and efforts to simulate cutting operations. This study presents the methodology of cutting operation which can be applied to all the procedure in the simulation of dismantling of nuclear facilities. We developed the cutting simulation module for cutting operation in the dismantling of the nuclear facilities based on proposed cutting methodology. We defined the requirement of model cutting methodology based on the requirement of the dismantling of nuclear facilities. And we implemented cutting simulation module based on API of the commercial CAD system.

Measuring multiple residual-stress components using the contour method and multiple cuts

Energy Technology Data Exchange (ETDEWEB)

Prime, Michael B [Los Alamos National Laboratory; Swenson, Hunter [Los Alamos National Laboratory; Pagliaro, Pierluigi [U. PALERMO; Zuccarello, Bernardo [U. PALERMO

2009-01-01

The conventional contour method determines one component of stress over the cross section of a part. The part is cut into two, the contour of the exposed surface is measured, and Bueckner's superposition principle is analytically applied to calculate stresses. In this paper, the contour method is extended to the measurement of multiple stress components by making multiple cuts with subsequent applications of superposition. The theory and limitations are described. The theory is experimentally tested on a 316L stainless steel disk with residual stresses induced by plastically indenting the central portion of the disk. The stress results are validated against independent measurements using neutron diffraction. The theory has implications beyond just multiple cuts. The contour method measurements and calculations for the first cut reveal how the residual stresses have changed throughout the part. Subsequent measurements of partially relaxed stresses by other techniques, such as laboratory x-rays, hole drilling, or neutron or synchrotron diffraction, can be superimposed back to the original state of the body.

Longitudinal Cut Method Revisited: A Survey on the Main Error Sources

OpenAIRE

Moriconi, Alessandro; Lalli, Francesco; Di Felice, Fabio; Esposito, Pier Giorgio; Piscopia, Rodolfo

2000-01-01

Some of the main error sources in wave pattern resistance determination were investigated. The experimental data obtained at the Italian Ship Model Basin (longitudinal wave cuts concerned with the steady motion of the Series 60 model and a hard-chine catamaran) were analyzed. It was found that, within the range of Froude numbers tested (0.225 ≤ Fr ≤ 0.345 for the Series 60 and 0.5 ≤ Fr ≤ 1 for the catamaran) two sources of uncertainty play a significant role: (i) the p...

Optimisation Of Cutting Parameters Of Composite Material Laser Cutting Process By Taguchi Method

Science.gov (United States)

Lokesh, S.; Niresh, J.; Neelakrishnan, S.; Rahul, S. P. Deepak

2018-03-01

The aim of this work is to develop a laser cutting process model that can predict the relationship between the process input parameters and resultant surface roughness, kerf width characteristics. The research conduct is based on the Design of Experiment (DOE) analysis. Response Surface Methodology (RSM) is used in this work. It is one of the most practical and most effective techniques to develop a process model. Even though RSM has been used for the optimization of the laser process, this research investigates laser cutting of materials like Composite wood (veneer)to be best circumstances of laser cutting using RSM process. The input parameters evaluated are focal length, power supply and cutting speed, the output responses being kerf width, surface roughness, temperature. To efficiently optimize and customize the kerf width and surface roughness characteristics, a machine laser cutting process model using Taguchi L9 orthogonal methodology was proposed.

On the Cutting Performance of Segmented Diamond Blades when Dry-Cutting Concrete.

Science.gov (United States)

Sánchez Egea, A J; Martynenko, V; Martínez Krahmer, D; López de Lacalle, L N; Benítez, A; Genovese, G

2018-02-09

The objective of the present study is to analyze and compare the cutting performance of segmented diamond blades when dry-cutting concrete. A cutting criteria is proposed to characterize the wear of the blades by measuring the variation of the external diameter and the weight loss of the blade. The results exhibit the cutting blade SB-A, which has twice the density of diamonds and large contact area, exhibits less wear even though the material removal rate is higher compared with the other two cutting blades. Additionally, the surface topography of the different blades is evaluated to examine the impact of wear depending on the surface profile and the distribution of the diamonds in the blade's matrix. Large number of diamonds pull-out are found in blades type SB-C, which additionally shows the worst wear resistant capability. As a conclusion, the cutting efficiency of the blade is found to be related to the density of embedded diamonds and the type of the surface profile of the cutting blade after reaching the stop criteria.

International cooperation project. Evaluation report on development of new oxidation and environment resistant materials for petroleum excavation; Sekiyu kussakuyo taisankasei taikankyosei shinzairyo no kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to enhance the environment and wear resisting performance of the bearing mechanism for petroleum excavation bits assuming use at a depth of 6,000 m, discussions were given on a cubic boron nitride based ultra-hard thin film and a Ti{sub x}M{sub 1-x}N based hard thin film as the new materials. This paper describes the evaluation report for the year 2000. It was found that the promising material is the Ti{sub x}M{sub 1-x}N. The practical applicability test would require a considerable amount of expense and insurance fee, while putting the material into practical use would take some more time. However, the achievements in developing this new material will allow the material to be applied to cutting tools used under the same onerous condition, and theoretical development would be possible on the consideration of the film properties, whereas further development may be expected in the future. An international joint study has performed evaluations on the environmental resistance and the characteristics of the film at the University of Toronto. These evaluations are effective in enhancing further the properties of the thin film in the future. Achievements have been accumulated steadily from starting the fundamental studies, and high level objectives have been achieved. Accurate identification has been made on the state of developing the parts for petroleum excavation bits, with the objectives set properly. Putting the bits into practical use will still require public assistance. (NEDO)

Error Analysis of 3D Metal Micromold Fabricated by Femtosecond Laser Cutting and Microelectric Resistance Slip Welding

Directory of Open Access Journals (Sweden)

Bin Xu

2013-01-01

Full Text Available We used micro-double-staged laminated object manufacturing process (micro-DLOM to fabricate 3D micromold. Moreover, the error of the micro-DLOM was also studied. Firstly, we got the principle error of the micro-DLOM. Based on the mathematical expression, it can be deduced that the smaller the opening angle α and the steel foil thickness h are, the smaller the principle error δ is. Secondly, we studied the error of femtosecond laser cutting. Through the experimental results, we know that the error of femtosecond laser cutting is 0.5 μm under 110 mW femtosecond laser power, 100 μm/s cutting speed, and 0.75 μm dimension compensation. Finally, we researched the error of microelectric resistance slip welding. Based on the research results, we can know that the minimum error of microcavity mold in the height direction is only 0.22 μm when welding voltage is 0.21 V and the number of slip welding discharge is 160.

Remotely controlled cutting techniques in the field of nuclear decommissioning. Overview of effectively applied thermal cutting methods

International Nuclear Information System (INIS)

Bienia, H.; Klotz, B.

2008-01-01

This article describes 3 thermal cutting technologies that are effectively used in nuclear decommissioning projects: the autonomous flame cutting, the plasma arc cutting and the contact arc metal cutting. The autonomous flame cutting technology is based on a high pressure oxygen jet oxidizing the material in a small kerf. Not all metal types are appropriate for this technology. The plasma arc cutting, in contrast to the previous technology, uses an electronically induced plasma arc to melt a kerf in the material. Inside the plasma arc temperatures up to 30.000 K exist, so in theory, this temperature is sufficient to cut all materials. Contact arc metal cutting is a new thermal cutting technology for under-water cutting works. Here, a carbon blade cuts the components. An electric arc between the cutting blade and component melts a kerf into the material easing the cutting. This technology allows the cutting of complex structures with hollows. The applications in nuclear facility dismantling of these 3 cutting technologies and their limits are reported and their requirements (staff, investment) listed in a table. (A.C.)

Monitoring Method of Cutting Force by Using Additional Spindle Sensors

Science.gov (United States)

Sarhan, Ahmed Aly Diaa; Matsubara, Atsushi; Sugihara, Motoyuki; Saraie, Hidenori; Ibaraki, Soichi; Kakino, Yoshiaki

This paper describes a monitoring method of cutting forces for end milling process by using displacement sensors. Four eddy-current displacement sensors are installed on the spindle housing of a machining center so that they can detect the radial motion of the rotating spindle. Thermocouples are also attached to the spindle structure in order to examine the thermal effect in the displacement sensing. The change in the spindle stiffness due to the spindle temperature and the speed is investigated as well. Finally, the estimation performance of cutting forces using the spindle displacement sensors is experimentally investigated by machining tests on carbon steel in end milling operations under different cutting conditions. It is found that the monitoring errors are attributable to the thermal displacement of the spindle, the time lag of the sensing system, and the modeling error of the spindle stiffness. It is also shown that the root mean square errors between estimated and measured amplitudes of cutting forces are reduced to be less than 20N with proper selection of the linear stiffness.

Nanometric mechanical cutting of metallic glass investigated using atomistic simulation

Energy Technology Data Exchange (ETDEWEB)

Wu, Cheng-Da, E-mail: nanowu@cycu.edu.tw [Department of Mechanical Engineering, Chung Yuan Christian University, 200, Chung Pei Rd., Chung Li District, Taoyuan City 32023, Taiwan (China); Fang, Te-Hua, E-mail: fang.tehua@msa.hinet.net [Department of Mechanical Engineering, National Kaohsiung University of Applied Sciences, Kaohsiung 807, Taiwan (China); Su, Jih-Kai, E-mail: yummy_2468@yahoo.com.tw [Department of Mechanical Engineering, National Kaohsiung University of Applied Sciences, Kaohsiung 807, Taiwan (China)

2017-02-28

Highlights: • A nanoscale chip with a shear plane of 135° is extruded by the tool. • Tangential force and normal force increase with increasing tool nose radius. • Resistance factor increases with increasing cutting depth and temperature. - Abstract: The effects of cutting depth, tool nose radius, and temperature on the cutting mechanism and mechanics of amorphous NiAl workpieces are studied using molecular dynamics simulations based on the second-moment approximation of the many-body tight-binding potential. These effects are investigated in terms of atomic trajectories and flow field, shear strain, cutting force, resistance factor, cutting ratio, and pile-up characteristics. The simulation results show that a nanoscale chip with a shear plane of 135° is extruded by the tool from a workpiece surface during the cutting process. The workpiece atoms underneath the tool flow upward due to the adhesion force and elastic recovery. The required tangential force and normal force increase with increasing cutting depth and tool nose radius; both forces also increase with decreasing temperature. The resistance factor increases with increasing cutting depth and temperature, and decreases with increasing tool nose radius.

Study of AFM-based nanometric cutting process using molecular dynamics

International Nuclear Information System (INIS)

Zhu Pengzhe; Hu Yuanzhong; Ma Tianbao; Wang Hui

2010-01-01

Three-dimensional molecular dynamics (MD) simulations are conducted to investigate the atomic force microscope (AFM)-based nanometric cutting process of copper using diamond tool. The effects of tool geometry, cutting depth, cutting velocity and bulk temperature are studied. It is found that the tool geometry has a significant effect on the cutting resistance. The friction coefficient (cutting resistance) on the nanoscale decreases with the increase of tool angle as predicted by the macroscale theory. However, the friction coefficients on the nanoscale are bigger than those on the macroscale. The simulation results show that a bigger cutting depth results in more material deformation and larger chip volume, thus leading to bigger cutting force and bigger normal force. It is also observed that a higher cutting velocity results in a larger chip volume in front of the tool and bigger cutting force and normal force. The chip volume in front of the tool increases while the cutting force and normal force decrease with the increase of bulk temperature.

Correlation methods in cutting arcs

Energy Technology Data Exchange (ETDEWEB)

Prevosto, L; Kelly, H, E-mail: prevosto@waycom.com.ar [Grupo de Descargas Electricas, Departamento Ing. Electromecanica, Universidad Tecnologica Nacional, Regional Venado Tuerto, Laprida 651, Venado Tuerto (2600), Santa Fe (Argentina)

2011-05-01

The present work applies similarity theory to the plasma emanating from transferred arc, gas-vortex stabilized plasma cutting torches, to analyze the existing correlation between the arc temperature and the physical parameters of such torches. It has been found that the enthalpy number significantly influence the temperature of the electric arc. The obtained correlation shows an average deviation of 3% from the temperature data points. Such correlation can be used, for instance, to predict changes in the peak value of the arc temperature at the nozzle exit of a geometrically similar cutting torch due to changes in its operation parameters.

Correlation methods in cutting arcs

International Nuclear Information System (INIS)

Prevosto, L; Kelly, H

2011-01-01

The present work applies similarity theory to the plasma emanating from transferred arc, gas-vortex stabilized plasma cutting torches, to analyze the existing correlation between the arc temperature and the physical parameters of such torches. It has been found that the enthalpy number significantly influence the temperature of the electric arc. The obtained correlation shows an average deviation of 3% from the temperature data points. Such correlation can be used, for instance, to predict changes in the peak value of the arc temperature at the nozzle exit of a geometrically similar cutting torch due to changes in its operation parameters.

Distribution network planning method considering distributed generation for peak cutting

International Nuclear Information System (INIS)

Ouyang Wu; Cheng Haozhong; Zhang Xiubin; Yao Liangzhong

2010-01-01

Conventional distribution planning method based on peak load brings about large investment, high risk and low utilization efficiency. A distribution network planning method considering distributed generation (DG) for peak cutting is proposed in this paper. The new integrated distribution network planning method with DG implementation aims to minimize the sum of feeder investments, DG investments, energy loss cost and the additional cost of DG for peak cutting. Using the solution techniques combining genetic algorithm (GA) with the heuristic approach, the proposed model determines the optimal planning scheme including the feeder network and the siting and sizing of DG. The strategy for the site and size of DG, which is based on the radial structure characteristics of distribution network, reduces the complexity degree of solving the optimization model and eases the computational burden substantially. Furthermore, the operation schedule of DG at the different load level is also provided.

Neodymium:YAG laser cutting of intraocular lens haptics.

Science.gov (United States)

Gorn, R A; Steinert, R F

1985-11-01

Neodymium:YAG laser cutting of polymethylmethacrylate and polypropylene anterior chamber and posterior chamber intraocular lens haptics was studied in terms of ease of transection and physical structure of the cut areas as seen by scanning electron microscopy. A marked difference was discovered, with the polymethylmethacrylate cutting easily along transverse planes, whereas the polypropylene resisted cutting along longitudinal fibers. Clinical guidelines are presented.

Logging costs and cutting methods in young-growth ponderosa pine in California

Science.gov (United States)

Philip M. McDonald; William A. Atkinson; Dale O. Hall

1969-01-01

Mixed-conifer stands at the Challenge Experimental Forest, Calif., were cut to four specifications: seed-tree, group selection, single tree selection, and clearcut. Logging costs and production rates were compared and evaluated. Cutting method had little effect on felling or skidding production; felling ranged from 1,802 to 2,019 bd ft per hour, and skidding from 3,138...

Study of Thermal Fatigue Resistance of a Composite Coating Made by a Vacuum Fusion Sintering Method

Institute of Scientific and Technical Information of China (English)

无

2003-01-01

Thermal fatigue behavior of a Ni-base alloy chromium carbide composite coating made by a vacuum fusion sintering method are discussed. Results show that thermal fatigue behavior is associated with cyclic upper temperature and coating thickness. As the thickness of the coating decreases, the thermal fatigue resistance increases. The thermal fatigue resistance cuts down with the thermal cyclic upper temperature rising. The crack growth rate decreases with the increase in cyclic number until crack arrests. Thermal fatigue failure was not found along the interface of the coating/matrix. The tract of thermal fatigue crack cracks along the interfaces of phases.

The analytic regularization ζ function method and the cut-off method in Casimir effect

International Nuclear Information System (INIS)

Svaiter, N.F.; Svaiter, B.F.

1990-01-01

The zero point energy associated to a hermitian massless scalar field in the presence of perfectly reflecting plates in a three dimensional flat space-time is discussed. A new technique to unify two different methods - the ζ function and a variant of the cut-off method - used to obtain the so called Casimir energy is presented, and the proof of the analytic equivalence between both methods is given. (author)

Wear and breakage monitoring of cutting tools by an optical method: theory

Science.gov (United States)

Li, Jianfeng; Zhang, Yongqing; Chen, Fangrong; Tian, Zhiren; Wang, Yao

1996-10-01

An essential part of a machining system in the unmanned flexible manufacturing system, is the ability to automatically change out tools that are worn or damaged. An optoelectronic method for in situ monitoring of the flank wear and breakage of cutting tools is presented. A flank wear estimation system is implemented in a laboratory environment, and its performance is evaluated through turning experiments. The flank wear model parameters that need to be known a priori are determined through several preliminary experiments, or from data available in the literature. The resulting cutting conditions are typical of those used in finishing cutting operations. Through time and amplitude domain analysis of the cutting tool wear states and breakage states, it is found that the original signal digital specificity (sigma) 2x and the self correlation coefficient (rho) (m) can reflect the change regularity of the cutting tool wear and break are determined, but which is not enough due to the complexity of the wear and break procedure of cutting tools. Time series analysis and frequency spectrum analysis will be carried out, which will be described in the later papers.

Ceramic cutting tools materials, development and performance

CERN Document Server

Whitney, E Dow

1994-01-01

Interest in ceramics as a high speed cutting tool material is based primarily on favorable material properties. As a class of materials, ceramics possess high melting points, excellent hardness and good wear resistance. Unlike most metals, hardness levels in ceramics generally remain high at elevated temperatures which means that cutting tip integrity is relatively unaffected at high cutting speeds. Ceramics are also chemically inert against most workmetals.

Inner tubes cutting method by electrical arc saw

International Nuclear Information System (INIS)

Thome, P.

1990-01-01

The research program deals on the definition of tools used for dismantling steam generator tubes bundle of PWR and on tool used for cutting pipes of great diameter by using the process of cutting by electrical arc saw. The remote tools are used for cutting by the interior pipes of contamined circuits [fr

Method and apparatus for jet-assisted drilling or cutting

Science.gov (United States)

Summers, David Archibold; Woelk, Klaus Hubert; Oglesby, Kenneth Doyle; Galecki, Grzegorz

2012-09-04

An abrasive cutting or drilling system, apparatus and method, which includes an upstream supercritical fluid and/or liquid carrier fluid, abrasive particles, a nozzle and a gaseous or low-density supercritical fluid exhaust abrasive stream. The nozzle includes a throat section and, optionally, a converging inlet section, a divergent discharge section, and a feed section.

Underwater transporting method and device for incore structure cutting piece

International Nuclear Information System (INIS)

Kurosawa, Koichi; Chiba, Noboru; Chiba, Isao; Takada, Hiroshi; Furukawa, Hideyasu; Chiba, Noboru.

1996-01-01

Cutting pieces are handled by using a pick-up device connected with a wire ropes, a take-up drum, chains and a winch as cutting piece handling means, and moved freely on the water surface by a propulsion machine of a transporting means of the device to transfer them under water to a predetermined position. The pick-up device is lifted by taking-up the rope by the rotation of the take-up drum using chain-driving by way of the winch and the chains. The cut pieces are stored in a cask by lowering them in the cask and releasing the handling. In addition, if the weight of the cut pieces is recognized before cutting, and the load of the weight of the cut pieces is applied to the device previously, the balance of the device and the cut pieces can be kept, and cut pieces can be transported under water always stably. Further, if the cut pieces are supported upon cutting operation, the cut pieces are made stable, and cutting operation with good efficiency can be attained. (N.H.)

Core Cutting Test with Vertical Rock Cutting Rig (VRCR)

Science.gov (United States)

Yasar, Serdar; Osman Yilmaz, Ali

2017-12-01

Roadheaders are frequently used machines in mining and tunnelling, and performance prediction of roadheaders is important for project economics and stability. Several methods were proposed so far for this purpose and, rock cutting tests are the best choice. Rock cutting tests are generally divided into two groups which are namely, full scale rock cutting tests and small scale rock cutting tests. These two tests have some superiorities and deficiencies over themselves. However, in many cases, where rock sampling becomes problematic, small scale rock cutting test (core cutting test) is preferred for performance prediction, since small block samples and core samples can be conducted to rock cutting testing. Common problem for rock cutting tests are that they can be found in very limited research centres. In this study, a new mobile rock cutting testing equipment, vertical rock cutting rig (VRCR) was introduced. Standard testing procedure was conducted on seven rock samples which were the part of a former study on cutting rocks with another small scale rock cutting test. Results showed that core cutting test can be realized successfully with VRCR with the validation of paired samples t-test.

Casimir effect in a d-dimensional flat spacetime and the cut-off method

International Nuclear Information System (INIS)

Svaiter, N.F.; Svaiter, B.F.

1989-01-01

The CasiMir efeect in a D-dimensional spacetime produced by a Hermitian massless scalar field in the presence of a pair of perfectly reflecting parallel flat plates is discussed. The exponential cut-off regularization method is employed. The regularized vacuum energy and the Casimir energy of this field are evaluated and a detailed analysis of the divergent terms in the regularized vacuum energy is carried out. The two-dimensional version of the Casimir effect is discussed by means of the same cut-off method. A comparison between the above method and the zeta function regularization procedure is presented in a way which gives the unification between these two methods in the present case. (author) [pt

Nanostructured diamond coatings for orthopaedic applications

Science.gov (United States)

CATLEDGE, S.A.; THOMAS, V.; VOHRA, Y.K.

2013-01-01

With increasing numbers of orthopaedic devices being implanted, greater emphasis is being placed on ceramic coating technology to reduce friction and wear in mating total joint replacement components, in order to improve implant function and increase device lifespan. In this chapter, we consider ultra-hard carbon coatings, with emphasis on nanostructured diamond, as alternative bearing surfaces for metallic components. Such coatings have great potential for use in biomedical implants as a result of their extreme hardness, wear resistance, low friction and biocompatibility. These ultra-hard carbon coatings can be deposited by several techniques resulting in a wide variety of structures and properties. PMID:25285213

A combination method of the theory and experiment in determination of cutting force coefficients in ball-end mill processes

Directory of Open Access Journals (Sweden)

Yung-Chou Kao

2015-10-01

Full Text Available In this paper, the cutting force calculation of ball-end mill processing was modeled mathematically. All derivations of cutting forces were directly based on the tangential, radial, and axial cutting force components. In the developed mathematical model of cutting forces, the relationship of average cutting force and the feed per flute was characterized as a linear function. The cutting force coefficient model was formulated by a function of average cutting force and other parameters such as cutter geometry, cutting conditions, and so on. An experimental method was proposed based on the stable milling condition to estimate the cutting force coefficients for ball-end mill. This method could be applied for each pair of tool and workpiece. The developed cutting force model has been successfully verified experimentally with very promising results.

METHODS FOR INOCULATION WITH Fusarium guttiforme AND GENETIC RESISTANCE OF PINEAPPLE ( Ananas comosus var. comosus

Directory of Open Access Journals (Sweden)

WANDREILLA MOREIRA GARCIA

2017-01-01

Full Text Available The objective of this work was to evaluate Fusarium guttiforme inoculation methods and genetic resistance of pineapple accessions. Thus, three experiments were conducted: pathogen inoculation of different leaf types ( B, D and F of pineapple (1, pathogen inoculation of pineapple cuttings and detached D leaves (2, and identification of resistance to fusariosis in 19 pineapple accessions (3 sampled in the State of Mato Grosso, Brazil. The cultivars Pérola (susceptible to fusariosis and BRS - Vitória (resistant to fusariosis were used as controls. The fusariosis severity was evaluated at 10, 15, 20, 25 and 30 days after inoculation with F. guttiforme . The lesion diameters (severity level were used in order to calculate the area under the disease progress curve (AUDPC. The inoculation of detached D leaves was the most efficient, fast and inexpensive method, and the one that most satisfactorily reproduced the disease symptoms. The period of 10 to 20 days after inoculation of the D detached leaves with the pathogen is the most suitable to evaluate the resistance of pineapple accessions to fusariosis. The lowest lesion area and AUDPC was found in the accession 1, in all evaluations. Thus, the accession 1 can be used in pineapple breeding programs for resistance to fusariosis.

Fast beam cut-off method in RF-knockout extraction for spot-scanning

CERN Document Server

Furukawa, T

2002-01-01

An irradiation method with magnetic scanning has been developed in order to provide accurate irradiation even for an irregular target shape. The scanning method has strongly required a lower ripple of the beam spill and a faster response to beam-on/off in slow extraction from a synchrotron ring. At HIMAC, RF-knockout extraction has utilized a bunched beam to reduce the beam-spill ripple. Therefore, particles near the resonance can be spilled out from the separatrices by synchrotron oscillation as well as by a transverse RF field. From this point of view, a fast beam cut-off method has been proposed and verified by both simulations and experiments. The maximum delay from the beam cut-off signal to beam-off has been improved to around 60 mu s from 700 mu s by a usual method. Unwanted dose has been considerably reduced by around a factor of 10 compared with that by the usual method.

Enlisting Clustering and Graph-Traversal Methods for Cutting Pattern and Net Topology Design in Pneumatic Hybrids

DEFF Research Database (Denmark)

Ayres, Phil; Vestartas, Petras; Ramsgaard Thomsen, Mette

2017-01-01

Cutting patterns for architectural membranes are generally characterised by rational approaches to surface discretisation and minimisation of geometric deviation between discrete elements that comprise the membrane. In this paper, we present an alternative approach for cutting pattern generation...... to the cutting pattern generation method and the net topology generation method used to produce a constraint net for a given membrane. We test our computational design approach through an iterative cycle of digital and physical prototyping before realising an air-inflated cable restrained pneumatic structural...

Stability analysis of multipoint tool equipped with metal cutting ceramics

Science.gov (United States)

Maksarov, V. V.; Khalimonenko, A. D.; Matrenichev, K. G.

2017-10-01

The article highlights the issues of determining the stability of the cutting process by a multipoint cutting tool equipped with cutting ceramics. There were some recommendations offered on the choice of parameters of replaceable cutting ceramic plates for milling based of the conducted researches. Ceramic plates for milling are proposed to be selected on the basis of value of their electrical volume resistivity.

Optimal cut-off of homeostasis model assessment of insulin resistance (HOMA-IR) for the diagnosis of metabolic syndrome: third national surveillance of risk factors of non-communicable diseases in Iran (SuRFNCD-2007).

Science.gov (United States)

Esteghamati, Alireza; Ashraf, Haleh; Khalilzadeh, Omid; Zandieh, Ali; Nakhjavani, Manouchehr; Rashidi, Armin; Haghazali, Mehrdad; Asgari, Fereshteh

2010-04-07

We have recently determined the optimal cut-off of the homeostatic model assessment of insulin resistance for the diagnosis of insulin resistance (IR) and metabolic syndrome (MetS) in non-diabetic residents of Tehran, the capital of Iran. The aim of the present study is to establish the optimal cut-off at the national level in the Iranian population with and without diabetes. Data of the third National Surveillance of Risk Factors of Non-Communicable Diseases, available for 3,071 adult Iranian individuals aging 25-64 years were analyzed. MetS was defined according to the Adult Treatment Panel III (ATPIII) and International Diabetes Federation (IDF) criteria. HOMA-IR cut-offs from the 50th to the 95th percentile were calculated and sensitivity, specificity, and positive likelihood ratio for MetS diagnosis were determined. The receiver operating characteristic (ROC) curves of HOMA-IR for MetS diagnosis were depicted, and the optimal cut-offs were determined by two different methods: Youden index, and the shortest distance from the top left corner of the curve. The area under the curve (AUC) (95%CI) was 0.650 (0.631-0.670) for IDF-defined MetS and 0.683 (0.664-0.703) with the ATPIII definition. The optimal HOMA-IR cut-off for the diagnosis of IDF- and ATPIII-defined MetS in non-diabetic individuals was 1.775 (sensitivity: 57.3%, specificity: 65.3%, with ATPIII; sensitivity: 55.9%, specificity: 64.7%, with IDF). The optimal cut-offs in diabetic individuals were 3.875 (sensitivity: 49.7%, specificity: 69.6%) and 4.325 (sensitivity: 45.4%, specificity: 69.0%) for ATPIII- and IDF-defined MetS, respectively. We determined the optimal HOMA-IR cut-off points for the diagnosis of MetS in the Iranian population with and without diabetes.

Method of distilling machine-cut peat and other finely divided material

Energy Technology Data Exchange (ETDEWEB)

1942-03-03

Apparatus arrangement is given for dry distillation of machine-cut peat and similar materials in particle or powder form, consisting of a tunnel oven through which the material is led and in which it is heated by help of the gases generated in the process. These gases are brought to circulate through the interior of the oven and heat exchangers installed outside the oven, are flushed by hot combustion gases. Through the tunnel oven a mounted turnable shaft is provided with paddles which lift the material and let it fall to make the particles of material get good contact with the circulating gases without offering too much resistance to the flow of the gases.

Multilayer composition coatings for cutting tools: formation and performance properties

Science.gov (United States)

Tabakov, Vladimir P.; Vereschaka, Anatoly S.; Vereschaka, Alexey A.

2018-03-01

The paper considers the concept of a multi-layer architecture of the coating in which each layer has a predetermined functionality. Latest generation of coatings with multi-layered architecture for cutting tools secure a dual nature of the coating, in which coatings should not only improve the mechanical and physical characteristics of the cutting tool material, but also reduce the thermo-mechanical effect on the cutting tool determining wear intensity. Here are presented the results of the development of combined methods of forming multi-layer coatings with improved properties. Combined method of forming coatings using a pulsed laser allowed reducing excessively high levels of compressive residual stress and increasing micro hardness of the multilayered coatings. The results in testing coated HSS tools showed that the use of additional pulse of laser processing increases tool life up to 3 times. Using filtered cathodic vacuum arc deposition for the generation of multilayer coatings based on TiAlN compound has increased the wear-resistance of carbide tools by 2 fold compared with tool life of cutting tool with commercial TiN coatings. The aim of this study was to develop an innovative methodological approach to the deposition of multilayer coatings for cutting tools with functional architectural selection, properties and parameters of the coating based on sound knowledge of coating failure in machining process.

Cutting tool wear monitoring with the use of impedance layers

OpenAIRE

Sadílek, Marek; Kratochvíl, Jiří; Petrů, Jana; Čep, Robert; Zlámal, Tomáš; Stančeková, Dana

2014-01-01

The article deals with problems of cutting process monitoring in real time. It is focused on tool wear by means of impedance layers applied on ceramic cutting inserts. In the experimental part the cutting process is monitored using electrical resistance measurement. The results are compared and verified using the monitored cutting temperature and tool wear. The testing of impedance layers is reasonable mainly for cutting edge diagnostics. The width of this layer determines the wear allowance ...

Welding and cutting

International Nuclear Information System (INIS)

Drews, P.; Schulze Frielinghaus, W.

1978-01-01

This is a survey, with 198 literature references, of the papers published in the fields of welding and cutting within the last three years. The subjects dealt with are: weldability of the materials - Welding methods - Thermal cutting - Shaping and calculation of welded joints - Environmental protection in welding and cutting. (orig.) [de

Ballistic resistant article, semi-finished product for and method of making a shell for a ballistic resistant article

NARCIS (Netherlands)

Harings, Jules Armand Wilhelmina; Janse, Gerardus Hubertus Anna

2013-01-01

The invention relates to a ballistic resistant article, such as a helmet (1), comprising a double curved shell in turn comprising a stack (5) of layers (6) of an oriented anti-ballistic material, the layers comprising one or more plies and having a plurality of cuts (7), the ends of which define a

Ballistic resistant article, semi-finished product for and method of making a shell for a ballistic resistant article

NARCIS (Netherlands)

Harings, Jules; Janse, Gerardus

2013-01-01

The invention relates to a ballistic resistant article, such as a helmet (1), comprising a double curved shell (2) in turn comprising a stack (5) of layers (6) of an oriented anti-ballistic material, the layers (6) comprising one or more plies and having a plurality of cuts (7), the ends of which

Paper Cuts.

Science.gov (United States)

Greene, Lisa A.

1990-01-01

Describes how to create paper cuts and suggests the most appropriate materials for young children that give good quality results. Describes the methods the author, a professional artist, uses to assemble her own paper cuts and how these can be adopted by older students. (KM)

Plasma cutting or laser cutting. Plasma setsudan ka laser setsudan ka

Energy Technology Data Exchange (ETDEWEB)

Nakamura, A. (Tanaka Engineering Works Ltd., Saitama (Japan))

1991-05-01

Comparisons and discussions were made on the plasma cutting and laser cutting in sheet steel cutting, referring partly to gas cutting. Historically, the cutting has been developed from gas, plasma, and laser in that order, and currently these three methods are used mixedly. Generally, the plasma cutting is superior in cutting speed, but inferior in cut face quality, and it requires measures of dust collection. Due to high accuracy and quality in cut face, the laser cutting has been practically used for quite some time in the thin sheet industry, but medium to thick sheet cutting had a problem of unavailability of high output laser suitable for these ranges. However, the recent technologies have overcome the problem as a result of development at the authors {prime} company of a 2 kW class laser cutter capable of cutting 19 mm thick sheet. The cutter has been proven being particularly excellent in controllability. Choice of whether plasma or laser would depend upon which priority is to be taken, cost or accuracy. 15 figs., 3 tabs.

The development of underwater remote cutting method for the disassembling of rotary specimen rack KRR-1 and 2

Energy Technology Data Exchange (ETDEWEB)

Lee, D. K.; Jung, K. H.; Lee, K. W.; Oh, W. J. [KAERI, Taejon (Korea, Republic of); Lee, K. Y. [Korea Institute of Industrial Technology, Kwangju (Korea, Republic of)

2004-07-01

The Rotary Specimen Racks (RSRs) were highly activated and then classified intermediate level radioactive waste for the decommissioning of KRR-1anel2. The RSR can be treated as low level radioactive waste after removing stainless steel parts. To reduce the volume of intermediate level radioactive waste, underwater cutting is required to separate stainless steel parts from RSR because of high radioactivity. In this study, the automatic remote cutting method was developed to disassemble RSR under water. For automatic remote cutting processes, a CAM (Computer Aided Manufacturing) system is employed. A computer inputs NC (Numerical Control) codes to the controller, which are based on CAM model, and the controller instructs the equipment to process according to NC codes automatically. And the cutting force model was improved to cut RSR stably. The automatic cutting was conducted using imitation of RSR and then it was resulted that the developed automatic cutting method can be safely disassemble stainless steel parts of RSR under water.

Aerodynamic Interactions During Laser Cutting

Science.gov (United States)

Fieret, J.; Terry, M. J.; Ward, B. A.

1986-11-01

Most laser cutting systems utilise a gas jet to remove molten or vaporised material from the kerf. The speed, economy and quality of the cut can be strongly dependent on the aerodynamic conditions created by the nozzle, workpiece proximity and kerf shape. Adverse conditions can be established that may lead to an unwelcome lack of reproducibility of cut quality. Relatively low gas nozzle pressures can result in supersonic flow in the jet with its associated shock fronts. When the nozzle is placed at conventional distances (1-2mm) above the workpiece, the force exerted by the gas on the workpiece and the cut products (the cutting pressure) can be significantly less than the nozzle pressure. Higher cutting pressures can be achieved by increasing the height of the nozzle above the workpiece, to a more damage resistant zone, provided that the shock structure of the jet is taken into account. Conventional conical nozzles with circular exits can be operated with conditions that will result in cutting pressures up to 3 Bar (g) in the more distant zone. At higher pressures in circular tipped nozzles the cutting pressure in this zone decays to inadequate levels. Investigations of a large number of non-circular nozzle tip shapes have resulted in the selection of a few specific shapes that can provide cutting pressures in excess of 6 Bar(g) at distances of 4 to 7mm from the nozzle tip. Since there is a strong correlation between cutting pressure and the speed and quality of laser cutting, the paper describes the aerodynamic requirements for achieving the above effects and reports the cutting results arising from the different nozzle designs and conditions. The results of the work of other investigators, who report anomalous laser cutting results, will be examined and reviewed in the light of the above work.

Effect of radiation resistance additives for insulation materials

International Nuclear Information System (INIS)

Yamamoto, Yasuaki; Yagyu, Hideki; Seguchi, Tadao.

1988-01-01

For the electric wires and cables used in radiation environment such as nuclear power stations and fuel reprocessing facilities, the properties of excellent radiation resistance are required. For these insulators and sheath materials, ethylene propylene rubber, polyethylene and other polymers have been used, but it cannot be said that they always have good radiation resistance. However, it has been well known that radiation resistance can be improved with small amount of additives, and heat resistance and burning retarding property as well as radiation resistance are given to the insulators of wires and cables for nuclear facilities by mixing various additives. In this research, the measuring method for quantitatively determining the effect of Anti-rad (radiation resistant additive) was examined. Through the measurement of gel fraction, radical formation and decomposed gas generation, the effect of Anti-rad protecting polymers from radiation deterioration was examined from the viewpoint of chemical reaction. The experimental method and the results are reported. The radiation energy for cutting C-H coupling is polymers is dispersed by Anti-rad, and the probability of cutting is lowered. Anti-rad catches and extinguishes radicals that start oxidation reaction. (K.I.)

CALCULATION OF LASER CUTTING COSTS

Directory of Open Access Journals (Sweden)

Bogdan Nedic

2016-09-01

Full Text Available The paper presents description methods of metal cutting and calculation of treatment costs based on model that is developed on Faculty of mechanical engineering in Kragujevac. Based on systematization and analysis of large number of calculation models of cutting with unconventional methods, mathematical model is derived, which is used for creating a software for calculation costs of metal cutting. Software solution enables resolving the problem of calculating the cost of laser cutting, comparison' of costs made by other unconventional methods and provides documentation that consists of reports on estimated costs.

Remote Laser Cutting of CFRP: Improvements in the Cut Surface

Science.gov (United States)

Stock, Johannes; Zaeh, Michael F.; Conrad, Markus

In the automotive industry carbon fibre reinforced plastics (CFRP) are considered as a future key material to reduce the weight of the vehicle. Therefore, capable production techniques are required to process this material in mass industry. E.g., state of the art methods for cutting are limited by the high tool wear or the feasible feed rate. Laser cutting processes are still under investigation. This paper presents detailed new studies on remote laser cutting of CFRP focusing on the influence of the material properties and the quality of the cut surface. By adding light absorbing soot particles to the resin of the matrix, the cutting process is improved and fewer defects emerge.

Investigation on welding and cutting methods for blanket support legs of fusion experimental reactors

International Nuclear Information System (INIS)

Tokami, Ikuhide; Nakahira, Masataka; Kurasawa, Toshimasa; Sato, Satoshi; Furuya, Kazuyuki; Hatano, Toshihisa; Takatsu, Hideyuki; Kuroda, Toshimasa.

1996-07-01

A toroidally-and poloidally-divided modular blanket has been proposed for a fusion experimental reactor, such as ITER, to enhance its maintainability as well as improve its fabricability. The blanket module, typically the size of 1 m wide, 1-2 m high and 0.4 m deep and the weight of 4 ton, will be supported by support legs which are extruded from back of the module and connected to a 70-100 mm thick strong back plate. The support leg has to withstand large electromagnetic force during plasma disruption and provide the way for in-situ module replacement by remote handling. For the connection method of the support leg to the back plate, a welding approach has been investigated here in terms of its high reliability against the large electromagnetic loads. For the welding approach, the support leg needs to be 70 mm thick, and the working space for welding/cutting heads are limited to 100 mm x 150 mm adjacent to the support leg. Based on a comparison of several welding methods, e.g. NGTIG, NGMIG and laser, NGTIG has been selected as a reference due to its well-established technology and the least R and D required. As for the cutting method, a plasma cutting has been given the highest priority to be pursued because of its compactness and high speed. Through preliminary design studies, the possibility of small welding/cutting heads that will work in the limited space has been shown, and maintenance route for in-situ module replacement with pre-and postfixture of the module has been investigated. Also preliminary R and Ds have resulted in; 1)the welding distortion is predictable according to the shape of weld groove and adjustable to meet the placement requirement of the module first wall, 2)the plasma cut surface can be rewelded without machining, 3)the welding/cutting time will meet the requirement of maintenance time. (author)

CALCULATION OF LASER CUTTING COSTS

OpenAIRE

Bogdan Nedic; Milan Eric; Marijana Aleksijevic

2016-01-01

The paper presents description methods of metal cutting and calculation of treatment costs based on model that is developed on Faculty of mechanical engineering in Kragujevac. Based on systematization and analysis of large number of calculation models of cutting with unconventional methods, mathematical model is derived, which is used for creating a software for calculation costs of metal cutting. Software solution enables resolving the problem of calculating the cost of laser cutting, compar...

Physicochemical, microbial and sensory quality of fresh-cut red beetroots in relation to sanization method and storage duration

Directory of Open Access Journals (Sweden)

Dulal Chandra

2015-06-01

Full Text Available Effects of sanitization and storage on fresh-cut beetroots (Beta vulgaris L. were evaluated following sanitation – peeling - cutting (SPC, peeling – sanitation – cutting (PSC and peeling – cutting – sanitation (PCS methods with (Cl, or without (TW, 100 ppm chlorine solution, then packaged in polyethylene bag and stored at 5°C for up to 14 days. Chroma values of fresh-cut beetroots significantly declined whereas whiteness index and titratable acidity values increased, however, texture and total soluble solid contents showed no significant variation. Betalain contents decreased gradually and total phenol content showed inconsistence trend. PCS-Cl treated samples accounted for higher betalains decline and received lower visual quality scores despite its lower total aerobic bacterial count. Minimum microbial population was observed in PSC-Cl methodsalong with higher levels of betalain contents. Considering pigment retention, microbial and visual qualities, beetroots sanitized with chlorine water following PSC method was the best processingway for fresh-cut beetroots and therefore, PSC-Cl treatment could commercially be used for processing of fresh-cut beetroots.

Water-Cut Sensor System

KAUST Repository

Karimi, Muhammad Akram; Shamim, Atif; Arsalan, Muhammad

2018-01-01

Provided in some embodiments is a method of manufacturing a pipe conformable water-cut sensors system. Provided in some embodiments is method for manufacturing a water-cut sensor system that includes providing a helical T-resonator, a helical ground

Polyester Apparel Cutting Waste as Insulation Material

OpenAIRE

Trajković, Dušan; Jordeva, Sonja; Tomovska, Elena; Zafirova, Koleta

2017-01-01

Polyester waste is the dominant component of the clothing industry waste stream, yet its recycling in this industry is rarely addressed. This paper proposes using polyester cutting waste as an insulation blanket for roofing and buildings’ internal walls in order to reduce environmental pollution. The designed textile structures used waste cuttings from different polyester fabrics without opening the fabric to fibre. Thermal insulation, acoustic insulation, fire resistance and biodegradation o...

Prevalence of tetracycline resistance and genotypic analysis of populations of Escherichia coli from animals, carcasses and cuts processed at a pig slaughterhouse

DEFF Research Database (Denmark)

Shuyu, Wu; Dalsgaard, Anders; Vieira, Antonio R

2009-01-01

A Danish pig slaughterhouse was visited in this study to investigate the impact of carcass processing on prevalence of tetracycline-resistant Escherichia coli, and to identify the origins of carcass contaminations with E. coli by assessing genetic diversity of E. coli populations on carcasses....... A total of 105 carcasses were sampled at five sequential stages: after stunning, after scalding, after splitting, after cooling and after cutting. Total and tetracycline-resistant E. coli were counted for each sample and tetracycline resistance prevalence per sample was calculated by the fraction...... of tetracycline-resistant E. coli out of total E. coli. From 15 repeatedly sampled carcasses, 422 E. coli isolates from faeces, stunned carcasses, split carcasses and chilled carcasses were examined by pulse-field gel electrophoresis (PFGE) and tested for antimicrobial susceptibility. The results showed that E...

Correction method for the error of diamond tool's radius in ultra-precision cutting

Science.gov (United States)

Wang, Yi; Yu, Jing-chi

2010-10-01

The compensation method for the error of diamond tool's cutting edge is a bottle-neck technology to hinder the high accuracy aspheric surface's directly formation after single diamond turning. Traditional compensation was done according to the measurement result from profile meter, which took long measurement time and caused low processing efficiency. A new compensation method was firstly put forward in the article, in which the correction of the error of diamond tool's cutting edge was done according to measurement result from digital interferometer. First, detailed theoretical calculation related with compensation method was deduced. Then, the effect after compensation was simulated by computer. Finally, φ50 mm work piece finished its diamond turning and new correction turning under Nanotech 250. Testing surface achieved high shape accuracy pv 0.137λ and rms=0.011λ, which approved the new compensation method agreed with predictive analysis, high accuracy and fast speed of error convergence.

Cutting characteristics and deformed layer of type 316LN stainless steel

International Nuclear Information System (INIS)

Oh, Sun Sae; Yi, Won

2004-01-01

The cutting characteristics and the deformed layer of Nitrogen(N)-added type 316LN stainless steel were comparatively investigated to type 316L stainless steel. The cutting force, the surface roughness(Ra) and the tool wear in face milling works were measured with cutting conditions, and the deformed layers were obtained from micro-hardness testing method. The cutting resistance of type 316LN was similar to type 316L in spite of its high strength. The surface roughness of type 316LN was superior to type 316L for all the cutting conditions. In particular, in the high cutting speed above 345m/min, the surface roughness of the two stainless steels was closely same. The deformed layer thickness of the two stainless steels was generated in the 150μm-300μm ranges, and its value of type 316LN was lower than that of type 316L. This is due to the high strength properties by nitrogen effect. It was found that type 316LN was higher in the tool wear than that type 316L, and flank wear was dominant to crater wear. In face milling works of type 316LN steel, tool wear is regarded as a important problem

Systems and Methods for Determining Water-Cut of a Fluid Mixture

KAUST Repository

Karimi, Muhammad Akram

2017-03-02

Provided in some embodiments are systems and methods for measuring the water content (or water-cut) of a fluid mixture. Provided in some embodiments is a water-cut sensor system that includes a T-resonator, a ground conductor, and a separator. The T-resonator including a feed line, and an open shunt stub conductively coupled to the feed line. The ground conductor including a bottom ground plane opposite the T-resonator and a ground ring conductively coupled to the bottom ground plane, with the feed line overlapping at least a portion of the ground ring. The separator including a dielectric material disposed between the feed line and the portion of the ground ring overlapped by the feed line, and the separator being adapted to electrically isolate the T-resonator from the ground conductor.

Designing for hot-blade cutting

DEFF Research Database (Denmark)

Brander, David; Bærentzen, Jakob Andreas; Clausen, Kenn

2016-01-01

In this paper we present a novel method for the generation of doubly-curved, architectural design surfaces using swept Euler elastica and cubic splines. The method enables a direct design to production workflow with robotic hot-blade cutting, a novel robotic fabrication method under development......-trivial constraints of blade-cutting in a bottom-up fashion, enabling an exploration of the unique architectural potential of this fabrication approach. The method is implemented as prototype design tools in MatLAB, C++, GhPython, and Python and demonstrated through cutting of expanded polystyrene foam design...

Combating Antibiotic Resistance

Science.gov (United States)

... Bacteria Phasing Out Certain Antibiotic Use in Farm Animals FDA: Cutting-Edge Technology Sheds Light on Antibiotic Resistance For More Information Antibiotics and Antibiotic Resistance Antimicrobial Resistance Information for Consumers and Health Professionals CDC: ...

Insulin resistance (HOMA-IR) cut-off values and the metabolic syndrome in a general adult population: effect of gender and age: EPIRCE cross-sectional study.

Science.gov (United States)

Gayoso-Diz, Pilar; Otero-González, Alfonso; Rodriguez-Alvarez, María Xosé; Gude, Francisco; García, Fernando; De Francisco, Angel; Quintela, Arturo González

2013-10-16

Insulin resistance has been associated with metabolic and hemodynamic alterations and higher cardio metabolic risk. There is great variability in the threshold homeostasis model assessment of insulin resistance (HOMA-IR) levels to define insulin resistance. The purpose of this study was to describe the influence of age and gender in the estimation of HOMA-IR optimal cut-off values to identify subjects with higher cardio metabolic risk in a general adult population. It included 2459 adults (range 20-92 years, 58.4% women) in a random Spanish population sample. As an accurate indicator of cardio metabolic risk, Metabolic Syndrome (MetS), both by International Diabetes Federation criteria and by Adult Treatment Panel III criteria, were used. The effect of age was analyzed in individuals with and without diabetes mellitus separately. ROC regression methodology was used to evaluate the effect of age on HOMA-IR performance in classifying cardio metabolic risk. In Spanish population the threshold value of HOMA-IR drops from 3.46 using 90th percentile criteria to 2.05 taking into account of MetS components. In non-diabetic women, but no in men, we found a significant non-linear effect of age on the accuracy of HOMA-IR. In non-diabetic men, the cut-off values were 1.85. All values are between 70th-75th percentiles of HOMA-IR levels in adult Spanish population. The consideration of the cardio metabolic risk to establish the cut-off points of HOMA-IR, to define insulin resistance instead of using a percentile of the population distribution, would increase its clinical utility in identifying those patients in whom the presence of multiple metabolic risk factors imparts an increased metabolic and cardiovascular risk. The threshold levels must be modified by age in non-diabetic women.

The Effect of Muscle Fiber Direction on the Cut Surface Angle of Frozen Fish Muscular Tissue Cut by Bending Force

OpenAIRE

岡本, 清; 羽倉, 義雄; 鈴木, 寛一; 久保田, 清

1996-01-01

We have proposed a new cutting method named "Cryo-cutting" for frozen foodstuffs by applying a bending force instead of conventional cutting methods with band saw. This paper investigated the effect of muscle fiber angle (θf) to cut surface angle (θs) of frozen tuna muscular tissue at -70, -100 and -130°C for the purpose of evaluating the applicability of the cryo-cutting method to frozen fishes. The results were as follows : (1) There were two typical cutting patterns ("across the muscle fib...

The effect of cutting origin and organic plant growth regulator on the growth of Daun Ungu (Graptophyllum pictum) through stem cutting method

Science.gov (United States)

Pratama, S. P.; Yunus, A.; Purwanto, E.; Widyastuti, Y.

2018-03-01

Graptophyllum pictum is one of medical plants which has important chemical content to treat diseases. Leaf, bark and flower can be used to facilitate menstruation, treat hemorrhoid, constipation, ulcers, ulcers, swelling, and earache. G. pictum is difficult to propagated by seedling due to the long duration of seed formation, thusvegetative propagation is done by stem cutting. The aims of this study are to obtain optimum combination of cutting origin and organic plant growth regulator in various consentration for the growth of Daun Ungu through stem cutting method. This research was conducted at Research center for Medicinal Plant and Traditional DrugTanjungsari, Tegal Gede, Karanganyar in June to August 2016. Origin of cuttings and organic plant growth regulator were used as treatments factor. A completely randomized design (RAL) is used and data were analyzed by F test (ANOVA) with a confidence level of 95%. Any significant differences among treatment followed with Duncan test at a = 5%. The research indicates that longest root was resulted from the treatment of 0,5 ml/l of organic plant growth regulator. The treatment of 1 ml/l is able to increase the fresh and dry weight of root, treatment of 1,5 ml/l of organic plant growth regulator was able to increase the percentage of growing shoots. Treatment of base part as origin of cuttings increases the length, fresh weight and and dry weight of shoot, increase the number of leaves. Interaction treatment between 1 ml/l consentration of organic plant growth regulator and central part origin of cuttings is capable of increasing the leaf area, whereas treatment without organic plant growth regulator and base part as planting material affects the smallest leaf area.

Advanced cutting, welding and inspection methods for vacuum vessel assembly and maintenance

Energy Technology Data Exchange (ETDEWEB)

Jones, L. E-mail: jonesl@ipp.mgg.de; Alfile, J.-P.; Aubert, Ph.; Punshon, C.; Daenner, W.; Kujanpaeae, V.; Maisonnier, D.; Serre, M.; Schreck, G.; Wykes, M

2000-11-01

ITER requires a 316 l stainless steel, double-skinned vacuum vessel (VV), each shell being 60 mm thick. EFDA (European Fusion Development Agreement) is investigating methods to be used for performing welding and NDT during VV assembly and also cutting and re-welding for remote sector replacement, including the development of an Intersector Welding Robot (IWR) [Jones et al. This conference]. To reduce the welding time, distortions and residual stresses of conventional welding, previous work concentrated on CO{sub 2} laser welding and cutting processes [Jones et al. Proc. Symp. Fusion Technol., Marseilles, 1998]. NdYAG laser now provides the focus for welding of the rearside root and for completing the weld for overhead positions with multipass filling. Electron beam (E-beam) welding with local vacuum offers a single-pass for most of the weld depth except for overhead positions. Plasma cutting has shown the capability to contain the backside dross and preliminary work with NdYAG laser cutting has shown good results. Automated ultrasonic inspection of assembly welds will be improved by the use of a phased array probe system that can focus the beam for accurate flaw location and sizing. This paper describes the recent results of process investigations in this R and D programme, involving five European sites and forming part of the overall VV/blanket research effort [W. Daenner et al. This conference].

Dictionary: Welding, cutting and allied processes. Pt. 2. German/English. Fachwoerterbuch: Schweissen, Schneiden und verwandte Verfahren. Bd. 2. Deutsch/Englisch

Energy Technology Data Exchange (ETDEWEB)

Kleiber, A W

1987-01-01

The dictionary contains approximately 40 000 entries covering all aspects of welding technology. It is based on the evaluation of numerous English, American and German sources. This comprehensive and up to date dictionary will be a reliable and helpful aid in evaluation and translating. The dictionary covers the following areas: Welding: gas welding, arc welding, gas shielded welding, resistance welding, welding of plastics, special welding processes; Cutting: flame cutting, arc cutting and special thermal cutting processes; Soldering: brazing and soldering; Other topics: thermal spraying, metal to metal adhesion, welding filler materials and other consumables, test methods, plant and equipment, accessories, automation, welding trade, general welding terminology.

Application of wire sawing method to decommissioning of nuclear power plant. Cutting test with turbine pedestal of thermal power plant

International Nuclear Information System (INIS)

Hasegawa, Hideki; Uchiyama, Noriyuki; Sugiyama, Kazuya; Yamashita, Yoshitaka; Watanabe, Morishige

1995-01-01

It is very important to reduce radioactive waste volume, and to reduce radiation dose to workers and to the public during dismantling of the activated concrete in the decommissioning stage of a nuclear power plant. For the above, we studied a dismantling method which can separate activated concrete from non-activated concrete safely and effectively. Considering the state of legal regulation about radioactive waste disposal, and the state of developing of decommissioning technologies, we come to a conclusion that wire sawing method is feasible as a concrete cutting method. This study was carried out to evaluate the availability of the wire sawing method to dismantling of concrete structures of nuclear power plants. This study consists of concrete cutting rate test and concrete block cutting test. The former is to obtain data about cutting rate with various steel ratios while the latter is to obtain data about working time and man hour of the whole work with wire sawing. Thirty-six year old turbine pedestal of a thermal power plant was selected as a test piece to simulate actual decommissioning work of nuclear power plant, taking its massive concrete volume and age. Taking account of the handling in the building, the wire sawing machine with motor driven was used in this study considering that it did not produce exhaust gas. The concrete cutting rate test was performed with parameter of steel ratio in the concrete, wire tension and cutting direction. In the concrete block cutting test, imaging the actual cutting situation, cubic blocks which side was approximately 1 meter were taken out, and a large block to be cut and to be taken out is a section of 1m x 1.5m x 10m. Test results are shown below. The difference of cutting rate was mainly caused by the difference of reinforcement steel ratio. Working time data of installation, removal of machines and cutting were obtained. Data on secondary waste (dust, drainage and sludge) and environmental effect (noise and

Systems and Methods for Determining Water-Cut of a Fluid Mixture

KAUST Repository

Karimi, Muhammad Akram

2017-12-07

Provided in some embodiments are systems and methods for measuring the water content (or water-cut) of a fluid mixture. Provided in some embodiments is a water-cut sensor system that includes a helical T-resonator, a helical ground conductor, and a separator provided at an exterior of a cylindrical pipe. The helical T-resonator including a feed line, and a helical open shunt stub conductively coupled to the feed line. The helical ground conductor including a helical ground plane opposite the helical open shunt stub and a ground ring conductively coupled to the helical ground plane. The feed line overlapping at least a portion of the ground ring, and the separator disposed between the feed line and the portion of the ground ring overlapped by the feed line to electrically isolate the helical T-resonator from the helical ground conductor.

Development of connecting method for mechanically cut reinforced concrete blocks

International Nuclear Information System (INIS)

Nishiuchi, Tatsuo

2005-01-01

The purpose of the study is to develop a practical method of disposing and recycling in dismantled reinforced concrete structures. We have devised a new method in which mechanically cut reinforced concrete blocks are connected and they are reused as a structural beam. In this method, concrete blocks are connected with several steel bars and the connected surface is wrapped with a fiber sheet. We verified that the load capacity of renewal beams was considerably large as same as that of continuous structural beams on the basis of experimental as well as numerical analysis results. As far as construction cost of reinforced concrete walls are concerned, we demonstrated that the cost of this method is slightly lower than that of the plan to use new and recycle materials. (author)

Multi-Criteria Analysis of Laser Cut Surface Characteristics in CO2 Laser Cutting of Stainless Steel

Directory of Open Access Journals (Sweden)

M. Radovanović

2015-06-01

Full Text Available In this paper an approach for multi-criteria analysis of laser cut surface characteristics using multi-criteria decision making (MCDM approach was presented. Laser cutting experiment was conducted based on Taguchi’s L27 experimental design by varying laser power, cutting speed, assist gas pressure and focus position at three levels. Multi-criteria analysis was performed by using the weighted aggregated sum product assessment (WASPAS method while considering burr height, drag line separation, depth of separation line, surface roughness and perpendicularity of the cut as assessment criteria. Based on conducted experimental investigation the MCDM model with 27 alternatives (laser cuts and five criteria was developed. The relative importance of criteria was determined by using pair-wise comparison matrix and geometric mean method of the analytic hierarchy process (AHP method.

α-Cut method based importance measure for criticality analysis in fuzzy probability – Based fault tree analysis

International Nuclear Information System (INIS)

Purba, Julwan Hendry; Sony Tjahyani, D.T.; Widodo, Surip; Tjahjono, Hendro

2017-01-01

Highlights: •FPFTA deals with epistemic uncertainty using fuzzy probability. •Criticality analysis is important for reliability improvement. •An α-cut method based importance measure is proposed for criticality analysis in FPFTA. •The α-cut method based importance measure utilises α-cut multiplication, α-cut subtraction, and area defuzzification technique. •Benchmarking confirm that the proposed method is feasible for criticality analysis in FPFTA. -- Abstract: Fuzzy probability – based fault tree analysis (FPFTA) has been recently developed and proposed to deal with the limitations of conventional fault tree analysis. In FPFTA, reliabilities of basic events, intermediate events and top event are characterized by fuzzy probabilities. Furthermore, the quantification of the FPFTA is based on fuzzy multiplication rule and fuzzy complementation rule to propagate uncertainties from basic event to the top event. Since the objective of the fault tree analysis is to improve the reliability of the system being evaluated, it is necessary to find the weakest path in the system. For this purpose, criticality analysis can be implemented. Various importance measures, which are based on conventional probabilities, have been developed and proposed for criticality analysis in fault tree analysis. However, not one of those importance measures can be applied for criticality analysis in FPFTA, which is based on fuzzy probability. To be fully applied in nuclear power plant probabilistic safety assessment, FPFTA needs to have its corresponding importance measure. The objective of this study is to develop an α-cut method based importance measure to evaluate and rank the importance of basic events for criticality analysis in FPFTA. To demonstrate the applicability of the proposed measure, a case study is performed and its results are then benchmarked to the results generated by the four well known importance measures in conventional fault tree analysis. The results

Calculation of chiral determinants and multiloop amplitudes by cutting and sewing method

International Nuclear Information System (INIS)

Losev, A.

1989-01-01

Functional integrals over fermions on open Riemann surfaces are determined up to a multiplicative constant by conservation laws. Using a cutting and sewing method these constants are found. Multiloop statsums and amplitudes as a product of anomaly-free expressions in Schottky parametrization and statsums on spheres are obtained. 5 refs

Characterization of structures of the Nankai Trough accretionary prism from integrated analyses of LWD log response, resistivity images and clay mineralogy of cuttings: Expedition 338 Site C0002

Science.gov (United States)

Jurado, Maria Jose; Schleicher, Anja

2014-05-01

The objective of our research is a detailed characterization of structures on the basis of LWD oriented images and logs,and clay mineralogy of cuttings from Hole C0002F of the Nankai Trough accretionary prism. Our results show an integrated interpretation of structures derived from borehole images, petrophysical characterization on LWD logs and cuttings mineralogy. The geometry of the structure intersected at Hole C0002F has been characterized by the interpretation of oriented borehole resistivity images acquired during IODP Expedition 338. The characterization of structural features, faults and fracture zones is based on a detailed post-cruise interpretation of bedding and fractures on borehole images and also on the analysis of Logging While Drilling (LWD) log response (gamma radioactivity, resistivity and sonic logs). The interpretation and complete characterization of structures (fractures, fracture zones, fault zones, folds) was achieved after detailed shorebased reprocessing of resistivity images, which allowed to enhance bedding and fracture's imaging for geometry and orientation interpretation. In order to characterize distinctive petrophysical properties based on LWD log response, it could be compared with compositional changes derived from cuttings analyses. Cuttings analyses were used to calibrate and to characterize log response and to verify interpretations in terms of changes in composition and texture at fractures and fault zones defined on borehole images. Cuttings were taken routinely every 5 m during Expedition 338, indicating a clay-dominated lithology of silty claystone with interbeds of weakly consolidated, fine sandstones. The main mineralogical components are clay minerals, quartz, feldspar and calcite. Selected cuttings were taken from areas of interest as defined on LWD logs and images. The clay mineralogy was investigated on the LWD) data allowed us to characterize structural, petrophysical and mineralogical properties at fracture and

Modeling of the Cutting Forces in Turning Process Using Various Methods of Cooling and Lubricating: An Artificial Intelligence Approach

Directory of Open Access Journals (Sweden)

Djordje Cica

2013-01-01

Full Text Available Cutting forces are one of the inherent phenomena and a very significant indicator of the metal cutting process. The work presented in this paper is an investigation of the prediction of these parameters in turning using soft computing techniques. During the experimental research focus is placed on the application of various methods of cooling and lubricating of the cutting zone. On this occasion were used the conventional method of cooling and lubricating, high pressure jet assisted machining, and minimal quantity lubrication technique. The data obtained by experiment are used to create two different models, namely, artificial neural network and adaptive networks based fuzzy inference systems for prediction of cutting forces. Furthermore, both models are compared with the experimental data and results are indicated.

OPTIMASI PARAMETER MESIN LASER CUTTING TERHADAP KEKASARAN DAN LAJU PEMOTONGAN PADA SUS 316L MENGGUNAKAN TAGUCHI GREY RELATIONAL ANALYSIS METHOD

Directory of Open Access Journals (Sweden)

Rakasita R

2016-06-01

Full Text Available Optimasi parameter adalah teknik yang digunakan pada proses manufaktur untuk menghasilkan produk terbaik. Penelitian ini bertujuan untuk mengoptimasi parameter CNC laser cutting, yaitu titik fokus sinar laser, tekanan gas cutting dan cutting speed untuk mengurangi variasi terhadap respon kekasaran dan laju pemotongan pada material SUS 316L. Masing-masing parameter memiliki 3 level dan pada penelitian ini menggunakan matriks orthogonal L9 (34. Metode ANOVA dan Taguchi digunakan untuk menganalisis data hasil percobaan. Optimasi kekasaran minimum permukaan dan laju pemotongan maksimum pada proses laser cutting dilakukan dengan menggunakan Grey relational analysis. Eksperimen konfirmasi digunakan untuk membuktikan hasil optimal yang telah didapatkan dari metode Taguchi Grey relational analysis. Hasil eksperimen menunjukkan bahwa Taguchi Grey relational analysis efektif digunakan untuk mengoptimasi parameter pemesinan pada laser cutting dengan multi respon.   Abstract Parameter optimization is used in manufacturing as an indicator to produce the best manufacturing product. This paper studies an optimization parameters of CNC laser cutting such as focus of laser beam, pressure cutting gases and cutting speed for reducing variation of surface roughness and cutting rate on material SUS 316L. Based on L9(34 orthogonal array parameters, it is analized using ANOVA based on Taguchi method. In order to optimaze the minimum surface roughness and maximum cutting rate in laser cutting process, it is used Grey relational analysis. The confirmation experiments used to validate the optimal results that has done by Taguchi method. The results show that the Taguchi Grey relational analysis is being effective to optimize the machining parameters for laser cutting process with two responses.

Cutting performance of TiCN–HSS cermet in dry machining

OpenAIRE

Canteli Fernández, José Antonio; Cantero Guisández, José Luis; Marín, N.C.; Gómez, B.; Gordo Odériz, Elena; Miguélez, Henar

2010-01-01

This work is focused on the cutting performance of a new cermet based on high-speed steel (HSS) matrix with hard phase TiCN. The processing route to manufacture the cermet M2+ 50 vol.% TiCN is described. Orthogonal cutting tests, carried out in a lathe showed the ability of the new cermet to achieve turning operations, showing reasonably wear resistance performing dry cutting operations. Tool life was significantly increased, when the cermet was compared with the reference materia...

Quality Analysis of Cutting Steel Using Laser

Directory of Open Access Journals (Sweden)

Vladislav Markovič

2013-02-01

Full Text Available The article explores the quality dependence of the edge surface of steel C45 LST EN 10083-1 obtained cutting the material using laser on different cutting regimes and variations in the thickness of trial steel. The paper presents the influence of the main modes of laser cutting equipment Trulaser 3030, including cutting speed, pressure, angle and the thickness of the surface on the quality characteristics of the sample. The quality of the edge after laser cutting is the most important indicator influencing such technological spread in industry worldwide. Laser cutting is the most popular method of material cutting. Therefore, the article focuses on cutting equipment, cutting defects and methods of analysis. Research on microstructure, roughness and micro-toughness has been performed with reference to edge samples. At the end of the publication, conclusions are drawn.Article in Lithuanian

Quality Analysis of Cutting Steel Using Laser

Directory of Open Access Journals (Sweden)

Vladislav Markovič

2012-12-01

Full Text Available The article explores the quality dependence of the edge surface of steel C45 LST EN 10083-1 obtained cutting the material using laser on different cutting regimes and variations in the thickness of trial steel. The paper presents the influence of the main modes of laser cutting equipment Trulaser 3030, including cutting speed, pressure, angle and the thickness of the surface on the quality characteristics of the sample. The quality of the edge after laser cutting is the most important indicator influencing such technological spread in industry worldwide. Laser cutting is the most popular method of material cutting. Therefore, the article focuses on cutting equipment, cutting defects and methods of analysis. Research on microstructure, roughness and micro-toughness has been performed with reference to edge samples. At the end of the publication, conclusions are drawn.Article in Lithuanian

Identification of the critical depth-of-cut through a 2D image of the cutting region resulting from taper cutting of brittle materials

Science.gov (United States)

Gu, Wen; Zhu, Zhiwei; Zhu, Wu-Le; Lu, Leyao; To, Suet; Xiao, Gaobo

2018-05-01

An automatic identification method for obtaining the critical depth-of-cut (DoC) of brittle materials with nanometric accuracy and sub-nanometric uncertainty is proposed in this paper. With this method, a two-dimensional (2D) microscopic image of the taper cutting region is captured and further processed by image analysis to extract the margin of generated micro-cracks in the imaging plane. Meanwhile, an analytical model is formulated to describe the theoretical curve of the projected cutting points on the imaging plane with respect to a specified DoC during the whole cutting process. By adopting differential evolution algorithm-based minimization, the critical DoC can be identified by minimizing the deviation between the extracted margin and the theoretical curve. The proposed method is demonstrated through both numerical simulation and experimental analysis. Compared with conventional 2D- and 3D-microscopic-image-based methods, determination of the critical DoC in this study uses the envelope profile rather than the onset point of the generated cracks, providing a more objective approach with smaller uncertainty.

Performance Testing of Cutting Fluids

DEFF Research Database (Denmark)

Belluco, Walter

The importance of cutting fluid performance testing has increased with documentation requirements of new cutting fluid formulations based on more sustainable products, as well as cutting with minimum quantity of lubrication and dry cutting. Two sub-problems have to be solved: i) which machining...... tests feature repeatability, reproducibility and sensitivity to cutting fluids, and ii) to what extent results of one test ensure relevance to a wider set of machining situations. The present work is aimed at assessing the range of validity of the different testing methods, investigating correlation...... within the whole range of operations, materials, cutting fluids, operating conditions, etc. Cutting fluid performance was evaluated in turning, drilling, reaming and tapping, and with respect to tool life, cutting forces, chip formation and product quality (dimensional accuracy and surface integrity...

Benefits of explosive cutting for nuclear-facility applications

International Nuclear Information System (INIS)

Hazelton, R.F.; Lundgren, R.A.; Allen, R.P.

1981-06-01

The study discussed in this report was a cost/benefit analysis to determine: (1) whether explosive cutting is cost effective in comparison with alternative metal sectioning methods and (2) whether explosive cutting would reduce radiation exposure or provide other benefits. Two separate approaches were pursued. The first was to qualitatively assess cutting methods and factors involved in typical sectioning cases and then compare the results for the cutting methods. The second was to prepare estimates of work schedules and potential radiation exposures for candidate sectioning methods for two hypothetical, but typical, sectioning tasks. The analysis shows that explosive cutting would be cost effective and would also reduce radiation exposure when used for typical nuclear facility sectioning tasks. These results indicate that explosive cutting should be one of the principal cutting methods considered whenever steel or similar metal structures or equipment in a nuclear facility are to be sectioned for repair or decommissioning. 13 figures, 7 tables

Analytical method for establishing indentation rolling resistance

Science.gov (United States)

Gładysiewicz, Lech; Konieczna, Martyna

2018-01-01

Belt conveyors are highly reliable machines able to work in special operating conditions. Harsh environment, long distance of transporting and great mass of transported martials are cause of high energy usage. That is why research in the field of belt conveyor transportation nowadays focuses on reducing the power consumption without lowering their efficiency. In this paper, previous methods for testing rolling resistance are described, and new method designed by authors was presented. New method of testing rolling resistance is quite simple and inexpensive. Moreover it allows to conduct the experimental tests of the impact of different parameters on the value of indentation rolling resistance such as core design, cover thickness, ambient temperature, idler travel frequency, or load value as well. Finally results of tests of relationship between rolling resistance and idler travel frequency and between rolling resistance and idler travel speed was presented.

Remotely controlled cutting techniques in the field of nuclear decommissioning. Overview of effectively applied thermal and non thermal cutting methods

International Nuclear Information System (INIS)

Bienia, H.

2008-01-01

Remote disassembly of radiologically burdened large components is among the most sophisticated and complex activities in the dismantling of nuclear installations. The required space for the technical equipment during the dismantling operations, especially for the removal of larger components is often an additional problem. Conventional cutting technologies like sawing with a disk saw or band saw require large and heavy frameworks as well as guiding systems with high rigidity. These solutions are expensive and sometimes not applicable. The essential question of all cutting and dismantling tasks is the physiological constitution of the component which will be dismantled. That means size, material and structure of the component. All these points are primarily technological questions. The last question is about the estimated costs of the used dismantling technology. Therefore following questions must be answered. How much are the investments for the cutting equipment itself and how much are the investments for the supporting equipment (e.g. necessary handling equipment)? Can I use this cutting equipment only for one special task or is it applicable for many tasks and therefore saves money because other cutting or dismantling technologies are dispensable? How long is the cutting time and what is the to control this technique required personnel? Four different cutting and dismantling technologies will be introduced and described. These four technologies differ in their principle of operation but all of them are used by cutting and dismantling tasks in nuclear power plants. (author)

Method for 3D noncontact measurements of cut trees package area

Science.gov (United States)

Knyaz, Vladimir A.; Vizilter, Yuri V.

2001-02-01

Progress in imaging sensors and computers create the background for numerous 3D imaging application for wide variety of manufacturing activity. Many demands for automated precise measurements are in wood branch of industry. One of them is the accurate volume definition for cut trees carried on the truck. The key point for volume estimation is determination of the front area of the cut tree package. To eliminate slow and inaccurate manual measurements being now in practice the experimental system for automated non-contact wood measurements is developed. The system includes two non-metric CCD video cameras, PC as central processing unit, frame grabbers and original software for image processing and 3D measurements. The proposed method of measurement is based on capturing the stereo pair of front of trees package and performing the image orthotranformation into the front plane. This technique allows to process transformed image for circle shapes recognition and calculating their area. The metric characteristics of the system are provided by special camera calibration procedure. The paper presents the developed method of 3D measurements, describes the hardware used for image acquisition and the software realized the developed algorithms, gives the productivity and precision characteristics of the system.

Development of cutting techniques of steel pipe by wire sawing

International Nuclear Information System (INIS)

Kamiyama, Yoshinori; Inai, Shinsuke

2004-01-01

A cutting method has a high cutting efficiency and enable cutting in safe. A wire saw cutting method is used for dismantling of massive concrete structures such as nuclear power plants with an effective and safe mean. In the case of dismantling of structures with multiple pipes installed at these facilities, an effective method is also demanded. If a wire saw method to remotely cut target objects in a large block in bulk is applicable, it will be expected an effective dismantling work under severe conditions with radioactivity. Although the wire saw method has adaptability for any shapes of cutting target objects and is widely adopted in dismantling of concrete constructs, it has few actual achievements in dismantling of steel structures such as steel pipe bundle. This study aims to verify its cutting characteristics and adaptability as a cutting method by conducting a cutting basic test to develop a diamond wire saw method to efficiently cut constructs with multiple pipes in a bundle. The test proved that a wire saw cutting method apply to dismantle structures with steel pipe bundle. A wire saw for metal cutting is adaptable in dismantling of bundle of thick carbon steel and stainless steel pipes. And also a wire saw for concrete cutting is adaptable in dismantling of pipe bundle structure with a mortar. (author)

Analytical method for establishing indentation rolling resistance

Directory of Open Access Journals (Sweden)

Gładysiewicz Lech

2018-01-01

Full Text Available Belt conveyors are highly reliable machines able to work in special operating conditions. Harsh environment, long distance of transporting and great mass of transported martials are cause of high energy usage. That is why research in the field of belt conveyor transportation nowadays focuses on reducing the power consumption without lowering their efficiency. In this paper, previous methods for testing rolling resistance are described, and new method designed by authors was presented. New method of testing rolling resistance is quite simple and inexpensive. Moreover it allows to conduct the experimental tests of the impact of different parameters on the value of indentation rolling resistance such as core design, cover thickness, ambient temperature, idler travel frequency, or load value as well. Finally results of tests of relationship between rolling resistance and idler travel frequency and between rolling resistance and idler travel speed was presented.

Feasibility Study of Cryogenic Cutting Technology by Using a Computer Simulation and Manufacture of Main Components for Cryogenic Cutting System

International Nuclear Information System (INIS)

Kim, Sung Kyun; Lee, Dong Gyu; Lee, Kune Woo; Song, Oh Seop

2009-01-01

Cryogenic cutting technology is one of the most suitable technologies for dismantling nuclear facilities due to the fact that a secondary waste is not generated during the cutting process. In this paper, the feasibility of cryogenic cutting technology was investigated by using a computer simulation. In the computer simulation, a hybrid method combined with the SPH (smoothed particle hydrodynamics) method and the FE (finite element) method was used. And also, a penetration depth equation, for the design of the cryogenic cutting system, was used and the design variables and operation conditions to cut a 10 mm thickness for steel were determined. Finally, the main components of the cryogenic cutting system were manufactures on the basis of the obtained design variables and operation conditions.

Experimental improvement of the technology of cutting of high-pressure hoses with metal braid on hand cutting machine

OpenAIRE

Karpenko, Mykola; Bogdevicius, Marijonas; Prentkovskis, Olegas

2016-01-01

In the article the review of the problem of improvement of technology of high pressure hoses cutting on the hand cutting machines is analyzed. Different methods of cutting of high pressure hoses into the billets are overviewed and the quality of edge cuts of hoses is analyzed. The comparison of treatment on automatic cutting machines and on hand cutting machines is carried out. Different experimental techniques of improvement of the quality of edges cutting of high pressure hoses are prese...

Development and characterization of AlCrN coated Si3N4 ceramic cutting tool

International Nuclear Information System (INIS)

Souza, J.V.C.; Nono, M.C.A.; Machado, J.P.B.; Silva, O.M.M.; Sa, F.C.L.

2010-01-01

Ceramic cutting tools are showing a growing market perspective in terms of application on machining operations due to their high hardness, wear resistance, and machining without a cutting fluid, therefore are good candidates for cast iron and Nickel superalloys machining. The objective of the present paper was the development of Si 3 N 4 based ceramic cutting insert, characterization of its physical and mechanical properties, and subsequent coating with AlCrN using a PVD method. The characterization of the coating was made using an optical profiler, XRD, AFM and microhardness tester. The results showed that the tool presented a fracture toughness of 6,43 MPa.m 1/2 and hardness of 16 GPa. The hardness reached 31 GPa after coating. The machining tests showed an improvement on work piece roughness when machining with coated insert, in comparison with the uncoated cutting tool. Probably this fact is related to hardness, roughness and topography of AlCrN. (author)

A Simple Method for the Assessment of Fusarium Head Blight Resistance in Korean Wheat Seedlings Inoculated with Fusarium graminearum

Directory of Open Access Journals (Sweden)

Sanghyun Shin

2014-03-01

Full Text Available Fusarium head blight (FHB; scab caused mainly by Fusarium graminearum is a devastating disease of wheat and barley around the world. FHB causes yield reductions and contamination of grain with trichothecene mycotoxins such as deoxynivalenol (DON which are a major health concern for humans and animals. The objective of this research was to develop an easy seed or seedling inoculation assay, and to compare these assays with whole plant resistance of twenty-nine Korean winter wheat cultivars to FHB. The clip-dipping assay consists of cutting off the coleoptiles apex, dipping the coleoptiles apex in conidial suspension, covering in plastic bag for 3 days, and measuring the lengths of lesions 7 days after inoculation. There were significant cultivar differences after inoculation with F. graminearum in seedling relative to the controls. Correlation coefficients between the lesion lengths of clip-dipping inoculation and FHB Type II resistance from adult plants were significant (r=0.45; P<0.05. Results from two other seedling inoculation methods, spraying and pin-point inoculation, were not correlated with adult FHB resistance. Single linear correlation was not significant between seed germination assays (soaking and soak-dry and FHB resistance (Type I and Type II, respectively. These results showed that clip-dipping inoculation method using F. graminearum may offer a real possibility of simple, rapid, and reliable for the early screening of FHB resistance in wheat.

Effect of the Cutting Tool Geometry on the Tool Wear Resistance When Machining Inconel 625

Directory of Open Access Journals (Sweden)

Tomáš Zlámal

2017-12-01

Full Text Available The paper deals with the design of a suitable cutting geometry of a tool for the machining of the Inconel 625 nickel alloy. This alloy is among the hard-to-machine refractory alloys that cause very rapid wear on cutting tools. Therefore, SNMG and RCMT indexable cutting insert were used to machine the alloy. The selected insert geometry should prevent notch wear and extend tool life. The alloy was machined under predetermined cutting conditions. The angle of the main edge and thus the size and nature of the wear changed with the depth of the material layer being cut. The criterion for determining a more suitable cutting geometry was the tool’s durability and the roughness of the machined surface.

Effect of the Cutting Tool Geometry on the Tool Wear Resistance when Machining Inconel 625

Directory of Open Access Journals (Sweden)

Tomáš Zlámal

2018-03-01

Full Text Available The paper deals with the design of a suitable cutting geometry of a tool for the machining of the Inconel 625 nickel alloy. This alloy is among the hard-to-machine refractory alloys that cause very rapid wear on cutting tools. Therefore, SNMG and RCMT indexable cutting insert were used to machine the alloy. The selected insert geometry should prevent notch wear and extend tool life. The alloy was machined under predetermined cutting conditions. The angle of the main edge and thus the size and nature of the wear changed with the depth of the material layer being cut. The criterion for determining a more suitable cutting geometry was the tool’s durability and the roughness of the machined surface.

[Efficacy on chronic obstructive pulmonary disease at stable stage treated with cutting method and western medication].

Science.gov (United States)

Xu, Jian-hua; Xu, Bin; Deng, Yan-qing

2014-10-01

To compare the difference in clinical efficacy on chronic obstructive pulmonary disease (COPD) at stable stage in the patients among the combined therapy of cutting method and western medication (combined therapy), simple cutting method and simple western medication. One hundred and twenty cases of COPD were randomized into three groups, 40 cases in each one. In the cutting method group, for excessive phlegm pattern/syndrome, Feishu (BL 13), Danzhong (CV 17), Dingchuan (EX-B 1) and Yuji (LU 10) were selected as the main acupoints, and Lieque (LU 7) and Pianli (LI 6) were as the supplementary acupoints. For the pattern/syndrome of failure to consolidate kidney primary, Shenshu (BL 23), Pishu (BL 20), Guanyuan (CV 4) and Yuji (LU 10) were selected as main acupoints, and Jueyinshu (BL 14) and Zusanli (ST 36) were as the supplementary acupoint. Three acupoints were selected alternatively in each treatment and the cutting method was applied once every 10 days. Three treatments made one session. Two sessions of treatment were required. In the western medication group, salbutamol sulfate aerosol, one press (200 μg/press) was used each night, as well as salmeterol xinafoate and fluticasone propionate powder for inhalation, one inhalation each night. The treatment of 1 month made one session. Two sessions were required. In the combined therapy group, the cutting method and western medication were applied in combination. The results of clinical symptom score, lung function test, arterial blood gas analysis, degree of inflation as well as clinical efficacy were observed before and after treatment in each group. Except the degree of lung inflation, the clinical symptom score, indices of lung function test, partial pressure of arterial blood gas (PaO2) and partial pressure of carbon dioxide (PaCO2) were all obviously improved after treatment as compared with those before treatment in each group (all Psyndrome differentiation and the combined therapy with western medication

Textile sensors for stab and cut detection

Science.gov (United States)

Graßmann, C.; Obermann, M.; Lempa, E.; Bache, T.; Siegel, P. K.; Freyer, T.; Paschko, S.; Beyer, T.; Kirsche, M.; Schwarz-Pfeiffer, A.

2017-10-01

Manufacturers are aiming for more flexible and lightweight protective clothing to increase wearing comfort. A cardigan with a knitted stab-resistant inlay and an alarm system is presented. The stab-resistant inlay is based on a multilayer ultra-high molecular weight poly ethylene (UHMW-PE) fabric. Stab resistance was evaluated according to the standard of the Association of Test Laboratories for Bullet, Stab or Pike Resistant Materials and Construction Standard (VPAM 2011). Furthermore sensors for the detection of cuts and pressure were integrated. Both sensors can trigger alarms if the wearer is attacked. Normal pressure occurring through leaning on a wall or sitting is filtered out and does not trigger an alarm.

Calcium Isotope Analysis with "Peak Cut" Method on Column Chemistry

Science.gov (United States)

Zhu, H.; Zhang, Z.; Liu, F.; Li, X.

2017-12-01

To eliminate isobaric interferences from elemental and molecular isobars (e.g., 40K+, 48Ti+, 88Sr2+, 24Mg16O+, 27Al16O+) on Ca isotopes during mass determination, samples should be purified through ion-exchange column chemistry before analysis. However, large Ca isotopic fractionation has been observed during column chemistry (Russell and Papanastassiou, 1978; Zhu et al., 2016). Therefore, full recovery during column chemistry is greatly needed, otherwise uncertainties would be caused by poor recovery (Zhu et al., 2016). Generally, matrix effects could be enhanced by full recovery, as other elements might overlap with Ca cut during column chemistry. Matrix effects and full recovery are difficult to balance and both need to be considered for high-precision analysis of stable Ca isotopes. Here, we investigate the influence of poor recovery on δ44/40Ca using TIMS with the double spike technique. The δ44/40Ca values of IAPSO seawater, ML3B-G and BHVO-2 in different Ca subcats (e.g., 0-20, 20-40, 40-60, 60-80, 80-100%) with 20% Ca recovery on column chemistry display limited variation after correction by the 42Ca-43Ca double spike technique with the exponential law. Notably, δ44/40Ca of each Ca subcut is quite consistent with δ44/40Ca of Ca cut with full recovery within error. Our results indicate that the 42Ca-43Ca double spike technique can simultaneously correct both of the Ca isotopic fractionation that occurred during column chemistry and thermal ionization mass spectrometry (TIMS) determination properly, because both of the isotopic fractionation occurred during analysis follow the exponential law well. Therefore, we propose the "peak cut" method on Ca column chemistry for samples with complex matrix effects. Briefly, for samples with low Ca contents, we can add the double spike before column chemistry, and only collect the middle of the Ca eluate and abandon the both sides of Ca eluate that might overlap with other elements (e.g., K, Sr). This method would

Cutting temperature measurement and material machinability

Directory of Open Access Journals (Sweden)

Nedić Bogdan P.

2014-01-01

Full Text Available Cutting temperature is very important parameter of cutting process. Around 90% of heat generated during cutting process is then away by sawdust, and the rest is transferred to the tool and workpiece. In this research cutting temperature was measured with artificial thermocouples and question of investigation of metal machinability from aspect of cutting temperature was analyzed. For investigation of material machinability during turning artificial thermocouple was placed just below the cutting top of insert, and for drilling thermocouples were placed through screw holes on the face surface. In this way was obtained simple, reliable, economic and accurate method for investigation of cutting machinability.

Investigation of cutting-induced damage in CMC bend bars

Directory of Open Access Journals (Sweden)

Neubrand A.

2015-01-01

Full Text Available Ceramic matrix composites (“CMC” with a strong fibre-matrix interface can be made damage-tolerant by introducing a highly porous matrix. Such composites typically have only a low interlaminar shear strength, which can potentially promote damage when preparing specimens or components by cutting. In order to investigate the damage induced by different cutting methods, waterjet cutting with and without abrasives, laser-cutting, wire eroding and cutoff grinding were used to cut plates of two different CMCs with a matrix porosity up to 35 vol.-%. For each combination of cutting method and composite, the flexural and interlaminar shear strength of the resulting specimens was determined. Additionally, the integrity of the regions near the cut surfaces was investigated by high-resolution x-ray computer tomography. It could be shown that the geometrical quality of the cut is strongly affected by the cutting method employed. Laser cut and waterjet cut specimens showed damage and delaminations near the cut surface leading to a reduced interlaminar shear strength of short bend bars in extreme cases.

Evaluation of epidemiological cut-off values indicates that biocide resistant subpopulations are uncommon in natural isolates of clinically-relevant microorganisms.

Directory of Open Access Journals (Sweden)

Ian Morrissey

Full Text Available To date there are no clear criteria to determine whether a microbe is susceptible to biocides or not. As a starting point for distinguishing between wild-type and resistant organisms, we set out to determine the minimal inhibitory concentration (MIC and minimal bactericidal concentration (MBC distributions for four common biocides; triclosan, benzalkonium chloride, chlorhexidine and sodium hypochlorite for 3319 clinical isolates, with a particular focus on Staphylococcus aureus (N = 1635 and Salmonella spp. (N = 901 but also including Escherichia coli (N = 368, Candida albicans (N = 200, Klebsiella pneumoniae (N = 60, Enterobacter spp. (N = 54, Enterococcus faecium (N = 53, and Enterococcus faecalis (N = 56. From these data epidemiological cut-off values (ECOFFs are proposed. As would be expected, MBCs were higher than MICs for all biocides. In most cases both values followed a normal distribution. Bimodal distributions, indicating the existence of biocide resistant subpopulations were observed for Enterobacter chlorhexidine susceptibility (both MICs and MBCs and the susceptibility to triclosan of Enterobacter (MBC, E. coli (MBC and MIC and S. aureus (MBC and MIC. There is a concern on the potential selection of antibiotic resistance by biocides. Our results indicate however that resistance to biocides and, hence any potential association with antibiotic resistance, is uncommon in natural populations of clinically relevant microorganisms.

Rooting Ability of Melia volkensii Cuttings Under Different Auxin Concentration Levels and Provenances

International Nuclear Information System (INIS)

Oeba, V.O; Muok, B.; Odee, D

2007-01-01

Melia volkensii is one of the most popular fast growing agro-forestry tree species in East Africa's arid and semi arid lands. It is valued for for production of termite resistant timber. Kenya Forestry Research Institute is carrying out studies on management, improvement and domestication of species with a major focus on improving low germination mortality and other propagation methods. Vegetative propagation was investigated in order to supplement more seedlings for increased demand of the species. The objective of this study was to determine and predict the effect of varying levels of auxin concentrations on rooting of melia volkensii shoot cuttings under different provenances. The experiment was set in a split plot design and conducted in a non-mist propagator. The number of roots was recorded for every cutting in the experiment. Mean cumulative cutting percentage were analysed using ANOVA procedures by first checking homogeneity of variance; Pearson correlation were carried out to check the interrelation of the factors with rooting and Logistic ability of the cuttings. The results showed that cuttings inoculated with 0.3 mgl-1 s ignificantly (p n ot showing any rooting from three provenances. In conclusion 0.03 mgl-1 s hould be used for further vegetative propagation of M. vokensii. Cutting from Taveta inoculated with 0.3 mgl-1 w ould significantly increase the number of seedlings for planting

Laser capture microdissection: Arcturus(XT) infrared capture and UV cutting methods.

Science.gov (United States)

Gallagher, Rosa I; Blakely, Steven R; Liotta, Lance A; Espina, Virginia

2012-01-01

Laser capture microdissection (LCM) is a technique that allows the precise procurement of enriched cell populations from a heterogeneous tissue under direct microscopic visualization. LCM can be used to harvest the cells of interest directly or can be used to isolate specific cells by ablating the unwanted cells, resulting in histologically enriched cell populations. The fundamental components of laser microdissection technology are (a) visualization of the cells of interest via microscopy, (b) transfer of laser energy to a thermolabile polymer with either the formation of a polymer-cell composite (capture method) or transfer of laser energy via an ultraviolet laser to photovolatize a region of tissue (cutting method), and (c) removal of cells of interest from the heterogeneous tissue section. Laser energy supplied by LCM instruments can be infrared (810 nm) or ultraviolet (355 nm). Infrared lasers melt thermolabile polymers for cell capture, whereas ultraviolet lasers ablate cells for either removal of unwanted cells or excision of a defined area of cells. LCM technology is applicable to an array of applications including mass spectrometry, DNA genotyping and loss-of-heterozygosity analysis, RNA transcript profiling, cDNA library generation, proteomics discovery, and signal kinase pathway profiling. This chapter describes the unique features of the Arcturus(XT) laser capture microdissection instrument, which incorporates both infrared capture and ultraviolet cutting technology in one instrument, using a proteomic downstream assay as a model.

Epidemiological cut-off values for Flavobacterium psychrophilum MIC data generated by a standard test protocol.

Science.gov (United States)

Smith, P; Endris, R; Kronvall, G; Thomas, V; Verner-Jeffreys, D; Wilhelm, C; Dalsgaard, I

2016-02-01

Epidemiological cut-off values were developed for application to antibiotic susceptibility data for Flavobacterium psychrophilum generated by standard CLSI test protocols. The MIC values for ten antibiotic agents against Flavobacterium psychrophilum were determined in two laboratories. For five antibiotics, the data sets were of sufficient quality and quantity to allow the setting of valid epidemiological cut-off values. For these agents, the cut-off values, calculated by the application of the statistically based normalized resistance interpretation method, were ≤16 mg L(-1) for erythromycin, ≤2 mg L(-1) for florfenicol, ≤0.025 mg L(-1) for oxolinic acid (OXO), ≤0.125 mg L(-1) for oxytetracycline and ≤20 (1/19) mg L(-1) for trimethoprim/sulphamethoxazole. For ampicillin and amoxicillin, the majority of putative wild-type observations were 'off scale', and therefore, statistically valid cut-off values could not be calculated. For ormetoprim/sulphadimethoxine, the data were excessively diverse and a valid cut-off could not be determined. For flumequine, the putative wild-type data were extremely skewed, and for enrofloxacin, there was inadequate separation in the MIC values for putative wild-type and non-wild-type strains. It is argued that the adoption of OXO as a class representative for the quinolone group would be a valid method of determining susceptibilities to these agents. © 2014 John Wiley & Sons Ltd.

Application of Taguchi method for cutting force optimization in rock

Indian Academy of Sciences (India)

In this paper, an optimization study was carried out for the cutting force (Fc) acting on circular diamond sawblades in rock sawing. The peripheral speed, traverse speed, cut depth and flow rate of cooling fluid were considered as operating variables and optimized by using Taguchi approach for the Fc. L16(44) orthogonal ...

Manufacturing Methods for Cutting, Machining and Drilling Composites. Volume 1. Composites Machining Handbook

Science.gov (United States)

1978-08-01

12°±30’ 1180±2° OPTIONAL .0005 IN./IN. BACK TAPER 015 RAD LIPS TO BE WITHIN .002 OF TRUE ANGULAR POSITION NOTES: 1. LAND WIDTH: 28% ± .005... horoscope and dye-penetrant requirements. 79 PHASE 1 PHASE II PHASE III PHASE IV CUTTING DRILLING MACHINING NONDESTRUCTIVE EVALUATION METHOD MATERIAL

Cutting agents for special metals

International Nuclear Information System (INIS)

Sugito, Seiji; Sakakibara, Fumi

1979-01-01

The quantity of use of special metals has increased year after year in the Plasma Research Institute, Nagoya University, with the development of researches on plasma and nuclear fusion. Most of these special metals are hard to cut, and in order to secure the surface smoothness and dimensional accuracy, considerable efforts are required. The method of experiment is as follows: cutting agents salt water and acetone, rape-seed oil, sulfide and chloride oil and water soluble cutting oil W grade 3; metals to be cut niobium, molybdenum, tantalum, titanium and tungsten; cutting conditions cutting speed 4.7 to 90 m/min, feed 0.07 to 0.2 mm/rev, depth of cut 0.1 to 0.4 mm, tool cemented carbide bit. Chemicals such as tetrachloromethane and trichloroethane give excellent cutting performance, but the toxicity is intense and the stimulative odor exists, accordingly they are hard to use practically. Cutting was easier when the salt water added with acetone was used than the case of rape-seed oil, but salt water is corrosive. Recently, the machining of molybdenum has been often carried out, and the water soluble cutting oil was the best. It is also good for cutting stainless steel, and its lubricating property is improved by adding some additives such as sulfur, chlorine, phosphorus and molybdenum disulfide. However after cutting with it, washing is required. (Kako, I.)

Plasma arc cutting: speed and cut quality

International Nuclear Information System (INIS)

Nemchinsky, V A; Severance, W S

2009-01-01

When cutting metal with plasma arc cutting, the walls of the cut are narrower at the bottom than at the top. This lack of squareness increases as the cutting speed increases. A model of this phenomenon, affecting cut quality, is suggested. A thin liquid layer, which separates the plasma from the solid metal to be melted, plays a key role in the suggested model. This layer decreases heat transfer from the plasma to the solid metal; the decrease is more pronounced the higher the speed and the thicker the liquid metal layer. Since the layer is thicker at the bottom of the cut, the heat transfer effectiveness is lower at the bottom. The decrease in heat transfer effectiveness is compensated by the narrowness of the cut. The suggested model allows one to calculate the profile of the cut. The result of the calculations of the cutting speeds for plates of various thicknesses, at which the squareness of the cut is acceptable, agrees well with the speeds recommended by manufacturers. The second effect considered in the paper is the deflection of the plasma jet from the vertical at a high cutting speed. A qualitative explanation of this phenomenon is given. We believe the considerations of this paper are pertinent to other types of cutting with moving heat sources.

Cutting

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español Cutting KidsHealth / For Teens / Cutting What's in this article? ... Getting Help Print en español Cortarse What Is Cutting? Emma's mom first noticed the cuts when Emma ...

An Overview of Integrated Management of Leaf-Cutting Ants (Hymenoptera: Formicidae in Brazilian Forest Plantations

Directory of Open Access Journals (Sweden)

Ronald Zanetti

2014-03-01

Full Text Available Brazilian forest producers have developed integrated management programs to increase the effectiveness of the control of leaf-cutting ants of the genera Atta and Acromyrmex. These measures reduced the costs and quantity of insecticides used in the plantations. Such integrated management programs are based on monitoring the ant nests, as well as the need and timing of the control methods. Chemical control employing baits is the most commonly used method, however, biological, mechanical and cultural control methods, besides plant resistance, can reduce the quantity of chemicals applied in the plantations.

A NEW METHOD FOR 3D SHAPE INDEXING AND RETRIEVAL IN LARGE DATABASE BY USING THE LEVEL CUT

OpenAIRE

M. Elkhal; A. Lakehal; K. Satori

2014-01-01

In this study, we propose a new method for indexing and retrieval of 3D models in large databases based on binary images extracted from the 3D object called “level cut” LC. These cuts are obtained by the intersection of the set of the plans with the 3D object. A set of equidistant parallel plans generates by the intersection with the 3D object a set of cuts that used to indexing the 3D model. We are based on these cuts to describe the 3D object by using the vectors descriptors bas...

Cut Locus Construction using Deformable Simplicial Complexes

DEFF Research Database (Denmark)

Misztal, Marek Krzysztof; Bærentzen, Jakob Andreas; Anton, François

2011-01-01

In this paper we present a method for appproximating cut loci for a given point p on Riemannian 2D manifolds, closely related to the notion of Voronoi diagrams. Our method finds the cut locus by advecting a front of points equally distant from p along the geodesics originating at p and finding...... the domain to have disk topology. We test our method for tori of revolution and compare our results to the benchmark ones from [2]. The method, however, is generic and can be easily adapted to construct cut loci for other manifolds of genera other than 1....

Development of cutting and welding methods for thick-walled stainless steel support and containment structures for ITER

International Nuclear Information System (INIS)

Jones, L.; Maisonnier, D.; Goussain, J.; Johnson, G.; Petring, D.; Wernwag, L.

1998-01-01

In ITER the containment and support structures are made from 316L(N)-IG (ITER Grade) stainless steel plate, 40 to 70 mm thick. The structures are divided into twenty sectors which have to be welded together in situ. The three areas of work described in this paper are, CO 2 laser welding, plasma cutting and CO 2 laser cutting. CO 2 laser welding offers significant advantages due to its high speed and low distortion and the most powerful commercial laser in Europe has been used to investigate single pass welding of thick plates, with strong welds up to 35 mm thick being achieved in one pass. For cutting, the space available on the back-side to collect debris and protect fragile components from damage is limited to 30 mm. A static, water-cooled backside protection plate proved unable to contain the debris from plasma cutting so a reciprocating backside protection system with dry ceramic heat shield demonstrated a solution. A 10 kW CO 2 laser system for nitrogen-assisted laser cutting, provided successful results at 40 mm thickness. This technique shows considerable promise as significant reductions in through power and rate of debris production are expected compared with plasma cutting and thicker cuts appear feasible. The results presented herein represent significant technical advances and will be strong candidates for the mix of methods which will have to be used for the assembly and maintenance of the ITER machine. (authors)

Laser Cutting of Carbon Fiber Fabrics

Science.gov (United States)

Fuchs, A. N.; Schoeberl, M.; Tremmer, J.; Zaeh, M. F.

Due to their high weight-specific mechanical stiffness and strength, parts made from carbon fiber reinforced polymers (CFRP) are increasingly used as structural components in the aircraft and automotive industry. However, the cutting of preforms, as with most automated manufacturing processes for CFRP components, has not yet been fully optimized. This paper discusses laser cutting, an alternative method to the mechanical cutting of preforms. Experiments with remote laser cutting and gas assisted laser cutting were carried out in order to identify achievable machining speeds. The advantages of the two different processes as well as their fitness for use in mass production are discussed.

EVALUATION OF THE CARBON FOOTPRINT OF INNOVATIVE WATER MAIN REHABILITATION TECHNOLOGIES VS. OPEN CUT METHODS

Science.gov (United States)

A major benefit of trenchless rehabilitation technologies touted by many practitioners when comparing their products with tradition open cut construction methods is lower carbon dioxide (CO2) emissions. In an attempt to verify these claims, multiple tools have been dev...

Influence of local or systemic corticosteroids on skin wound healing resistance Influência de corticosteróide local e sistêmico no processo cicatricial cutâneo

Directory of Open Access Journals (Sweden)

Luiz Ronaldo Alberti

2012-04-01

Full Text Available PURPOSE: To compare the resistance of skin wound healing of mice submitted to local or systemic hydrocortisone administration, in different postoperative periods. METHODS: An incision and suture was performed on the thoracic skin of 130 male mice: Group 1 (n = 10 resistance of the integer skin; Group 2 (n = 30 submitted only to skin incision and suture; Group 3 (n = 30 skin incision and suture followed by administration of saline fluid; Group 4 (n = 30 skin incision and suture followed by administration of local hydrocortisone; Group 5 (n = 30 skin incision and suture followed by administration of systemic hydrocortisone. The resistance of the wound healing and the weight of the animals were studied on the seventh, 14th and 21st postoperative days. Histological examination was also performed. RESULTS: The mice that received corticoid (groups 4 and 5 presented significant decreasing on their weight (p = 0.02. The Groups 3, 4 and 5 showed lower scar resistance than Group 2 on the seventh postoperative day (p 0.05. CONCLUSION: Administration of hydrocortisone in mice is responsible for weight decreasing and reduction of the skin wound healing resistance during the first postoperative week.OBJETIVO: Comparar a resistência cicatricial cutânea de camundongos submetidos a administração de hidrocortisona por diferentes vias e em distintos períodos pós-operatórios. MÉTODOS: Foram estudados 130 camundongos machos submetidos à incisão e sutura de pele da região dorsal do tórax: Grupo 1 (n = 10 resistência da pele íntegra; Grupo 2 (n = 30 incisão da pele e sutura, sem administração de corticóide; Grupo 3 (n = 30 incisão da pele e sutura, seguidas de injeção local de solução salina; Grupo 4 (n = 30 incisão da pele e sutura, seguidas de injeção local de hidrocortisona e Grupo 5 (n = 30 incisão da pele e sutura, seguidas de injeção intraperitoneal de hidrocortisona. Foram avaliadas a resistência cicatricial da pele e a varia

A non-linear branch and cut method for solving discrete minimum compliance problems to global optimality

DEFF Research Database (Denmark)

Stolpe, Mathias; Bendsøe, Martin P.

2007-01-01

This paper present some initial results pertaining to a search for globally optimal solutions to a challenging benchmark example proposed by Zhou and Rozvany. This means that we are dealing with global optimization of the classical single load minimum compliance topology design problem with a fixed...... finite element discretization and with discrete design variables. Global optimality is achieved by the implementation of some specially constructed convergent nonlinear branch and cut methods, based on the use of natural relaxations and by applying strengthening constraints (linear valid inequalities......) and cuts....

A method to improve tree water use estimates by distinguishing sapwood from heartwood using Electrical Resistivity Tomography

Science.gov (United States)

Guyot, A.; Ostergaard, K.; Lenkopane, M.; Fan, J.; Lockington, D. A.

2011-12-01

Estimating whole-plant water use in trees requires reliable and accurate methods. Measuring sap velocity and extrapolating to tree water use is seen as the most commonly used. However, deducing the tree water use from sap velocity requires an estimate of the sapwood area. This estimate is the highest cause of uncertainty, and can reach more than 50 % of the uncertainty in the estimate of water use per day. Here, we investigate the possibility of using Electrical Resistivity Tomography to evaluate the sapwood area distribution in a plantation of Pinus elliottii. Electric resistivity tomographs of Pinus elliottii show a very typical pattern of electrical resistivity, which is highly correlated to sapwood and heartwood distribution. To identify the key factors controlling the variation of electrical resistivity, cross sections at breast height for ten trees have been monitored with electrical resistivity tomography. Trees have been cut down after the experiment to identify the heartwood/sapwood boundaries and to extract wood and sap samples. pH, electrolyte concentration and wood moisture content have then been analysed for these samples. Results show that the heartwood/sapwood patterns are highly correlated with electrical resistivity, and that the wood moisture content is the most influencing factor controlling the variability of the patterns. These results show that electric resistivity tomography could be used as a powerful tool to identify the sapwood area, and thus be used in combination with sapflow sensors to map tree water use at stand scale. However, if Pinus elliottii shows typical patterns, further work is needed to identify to see if there are species - specific characterictics as shown in previous works (, electrolyte gradients from the bark to the heartwood). Also, patterns of high resistivity in between needles positions, which are not correlated with either wood moisture content or sapwood, appear to be artifacts. Thus, inversion methods have also to

Radioactive wear measurements of cutting tools made of metal in cutting aluminium alloys

International Nuclear Information System (INIS)

Frevert, E.

1977-01-01

The possibility of making quick checkings of the inhomogeneities of turning materials with radioactive wear measurements has been tested. After activation analysis of the long-lived radioisotopes of cutting tools made of hard metal a method for loss-free collection of the turnings has been developed. The detection limit of the abrasion is about 10 -8 g, the measuring times are 5-10 minutes. Special radiation protection measures are not necessary. An analysis of the abrasion showed that at the beginning of cutting the amount of cobalt is 6 times higher than in the normal composition of the used cutting tools. (author)

Determination of cut front position in laser cutting

Science.gov (United States)

Pereira, M.; Thombansen, U.

2016-07-01

Laser cutting has a huge importance to manufacturing industry. Laser cutting machines operate with fixed technological parameters and this does not guarantee the best productivity. The adjustment of the cutting parameters during operation can improve the machine performance. Based on a coaxial measuring device it is possible to identify the cut front position during the cutting process. This paper describes the data analysis approach used to determine the cut front position for different feed rates. The cut front position was determined with good resolution, but improvements are needed to make the whole process more stable.

Laser circular cutting of Kevlar sheets: Analysis of thermal stress filed and assessment of cutting geometry

Science.gov (United States)

Yilbas, B. S.; Akhtar, S. S.; Karatas, C.

2017-11-01

A Kevlar laminate has negative thermal expansion coefficient, which makes it difficult to machine at room temperaures using the conventional cutting tools. Contararily, laser machining of a Kevlar laminate provides advantages over the conventional methods because of the non-mechanical contact between the cutting tool and the workpiece. In the present study, laser circular cutting of Kevlar laminate is considered. The experiment is carried out to examine and evaluate the cutting sections. Temperature and stress fields formed in the cutting section are simulated in line with the experimental study. The influence of hole diameters on temperature and stress fields are investigated incorporating two different hole diameters. It is found that the Kevlar laminate cutting section is free from large size asperities such as large scale sideways burnings and attachemnt of charred residues. The maximum temperature along the cutting circumference remains higher for the large diameter hole than that of the small diameter hole. Temperature decay is sharp around the cutting section in the region where the cutting terminates. This, in turn, results in high temperature gradients and the thermal strain in the cutting region. von Mises stress remains high in the region where temperature gradients are high. von Mises stress follows similar to the trend of temperature decay around the cutting edges.

Electric arc, water jet cutting of metals

International Nuclear Information System (INIS)

Bruening, D.

1991-01-01

For thermal dismantling and cutting of metallic components, as electric arc, water jet cutting method was developed that can be used for underwater cutting work up to a depth of 20 m. Short-circuiting of a continuously fed electrode wire in contact with the metal generates an electric arc which induces partial melting of the metal, and the water jet surrounding the wire rinses away the molten material, thus making a continuous kerf in the material. The method was also tested and modified to allow larger area, surface cutting and removal of metallic surface coatings. This is achieved by melting parts of the surface with the electric arc and subsequent rinsing by the water jet. The cutting and melting depth for surface removal can be accurately controlled by the operating parameters chosen. (orig./DG) [de

Prevalence and behavior of multidrug-resistant Salmonella strains on raw whole and cut nopalitos (Opuntia ficus-indica L.) and on nopalitos salads.

Science.gov (United States)

Gómez-Aldapa, Carlos A; Gutiérrez-Alcántara, Eduardo J; Torres-Vitela, M Refugio; Rangel-Vargas, Esmeralda; Villarruel-López, Angelica; Castro-Rosas, Javier

2017-09-01

The presence of multidrug-resistant Salmonella in vegetables is a significant public health concern. Nopalito is a cactaceous that is commonly consumed either raw or cooked in Mexico and other countries. The presence of antibiotic-resistant Salmonella strains on raw whole nopalitos (RWN, without prickles), raw nopalitos cut into squares (RNCS) and in cooked nopalitos salads (CNS) samples was determined. In addition, the behavior of multidrug-resistant Salmonella isolates on RWN, RNCS and CNS at 25° ± 2 °C and 3° ± 2 °C was investigated. One hundred samples of RWN, 100 of RNCS and 100 more of CNS were collected from public markets. Salmonella strains were isolated and identified in 30, 30 and 10% of the samples, respectively. Seventy multidrug-resistant Salmonella strains were isolated from all the nopalitos samples. Multidrug-resistant Salmonella isolates survived at least 15 days on RWN at 25° ± 2 °C or 3° ± 2 °C. Multidrug-resistant Salmonella isolates grew in the RNCS and CNS samples at 25° ± 2 °C. However, at 3° ± 2 °C the bacterial growth was inhibited. This is the first report about multidrug-resistant Salmonella isolation from raw nopalitos and nopalitos salads. Nopalitos from markets are very likely to be an important factor contributing to the endemicity of multidrug-resistant Salmonella-related gastroenteritis in Mexico. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Experimental testing of exchangeable cutting inserts cutting ability

OpenAIRE

Čep, Robert; Janásek, Adam; Čepová, Lenka; Petrů, Jana; Hlavatý, Ivo; Car, Zlatan; Hatala, Michal

2013-01-01

The article deals with experimental testing of the cutting ability of exchangeable cutting inserts. Eleven types of exchangeable cutting inserts from five different manufacturers were tested. The tested cutting inserts were of the same shape and were different especially in material and coating types. The main aim was both to select a suitable test for determination of the cutting ability of exchangeable cutting inserts and to design such testing procedure that could make it possible...

Modelling of tunnelling processes and rock cutting tool wear with the particle finite element method

Science.gov (United States)

Carbonell, Josep Maria; Oñate, Eugenio; Suárez, Benjamín

2013-09-01

Underground construction involves all sort of challenges in analysis, design, project and execution phases. The dimension of tunnels and their structural requirements are growing, and so safety and security demands do. New engineering tools are needed to perform a safer planning and design. This work presents the advances in the particle finite element method (PFEM) for the modelling and the analysis of tunneling processes including the wear of the cutting tools. The PFEM has its foundation on the Lagrangian description of the motion of a continuum built from a set of particles with known physical properties. The method uses a remeshing process combined with the alpha-shape technique to detect the contacting surfaces and a finite element method for the mechanical computations. A contact procedure has been developed for the PFEM which is combined with a constitutive model for predicting the excavation front and the wear of cutting tools. The material parameters govern the coupling of frictional contact and wear between the interacting domains at the excavation front. The PFEM allows predicting several parameters which are relevant for estimating the performance of a tunnelling boring machine such as wear in the cutting tools, the pressure distribution on the face of the boring machine and the vibrations produced in the machinery and the adjacent soil/rock. The final aim is to help in the design of the excavating tools and in the planning of the tunnelling operations. The applications presented show that the PFEM is a promising technique for the analysis of tunnelling problems.

Determination of cut front position in laser cutting

International Nuclear Information System (INIS)

Pereira, M; Thombansen, U

2016-01-01

Laser cutting has a huge importance to manufacturing industry. Laser cutting machines operate with fixed technological parameters and this does not guarantee the best productivity. The adjustment of the cutting parameters during operation can improve the machine performance. Based on a coaxial measuring device it is possible to identify the cut front position during the cutting process. This paper describes the data analysis approach used to determine the cut front position for different feed rates. The cut front position was determined with good resolution, but improvements are needed to make the whole process more stable. (paper)

Generation Mechanism of Work Hardened Surface Layer in Metal Cutting

Science.gov (United States)

Hikiji, Rikio; Kondo, Eiji; Kawagoishi, Norio; Arai, Minoru

Finish machining used to be carried out in grinding, but it is being replaced by cutting with very small undeformed chip thickness. In ultra precision process, the effects of the cutting conditions and the complicated factors on the machined surface integrity are the serious problems. In this research, work hardened surface layer was dealt with as an evaluation of the machined surface integrity and the effect of the mechanical factors on work hardening was investigated experimentally in orthogonal cutting. As a result, it was found that work hardened surface layer was affected not only by the shear angle varied under the cutting conditions and the thrust force of cutting resistance, but also by the thrust force acting point, the coefficient of the thrust force and the compressive stress equivalent to the bulk hardness. Furthermore, these mechanical factors acting on the depth of the work hardened surface layer were investigated with the calculation model.

Biotechnological Methods for Precise Diagnosis of Methicillin Resistance in Staphylococci

Directory of Open Access Journals (Sweden)

Aija Zilevica

2005-04-01

Full Text Available Antimicrobial resistance is one of the most urgent problems in medicine nowadays. The purpose of the study was to investigate the microorganisms resistant to first-line antimicrobials, including gram-positive cocci, particularly the methicillin-resistant Staphylococcus aureus and coagulase-negative Staphylococci, the major agents of nosocomial infections. Owing to the multi-resistance of these agents, precise diagnosis of the methicillin resistance of Staphylococci is of greatest clinical importance. It is not enough to use only conventional microbiological diagnostic methods. Biotechnological methods should be also involved. In our studies, the following methicillin resistance identification methods were used: the disk diffusion method, detection of the mecA gene by PCR, E-test and Slidex MRSA test. For molecular typing, PFGL, RAPD tests and detection of the coa gene were used. All the MRS strains were multiresistant to antibacterials. No vancomycine resistance was registered.

Optimal Cut-Offs of Homeostasis Model Assessment of Insulin Resistance (HOMA-IR) to Identify Dysglycemia and Type 2 Diabetes Mellitus: A 15-Year Prospective Study in Chinese.

Science.gov (United States)

Lee, C H; Shih, A Z L; Woo, Y C; Fong, C H Y; Leung, O Y; Janus, E; Cheung, B M Y; Lam, K S L

The optimal reference range of homeostasis model assessment of insulin resistance (HOMA-IR) in normal Chinese population has not been clearly defined. Here we address this issue using the Hong Kong Cardiovascular Risk Factor Prevalence Study (CRISPS), a prospective population-based cohort study with long-term follow-up. In this study, normal glucose tolerance (NGT), impaired fasting glucose (IFG), impaired glucose tolerance (IGT) and type 2 diabetes mellitus (T2DM) were defined according to the 1998 World Health Organization criteria. Dysglycemia referred to IFG, IGT or T2DM. This study comprised two parts. Part one was a cross-sectional study involving 2,649 Hong Kong Chinese subjects, aged 25-74 years, at baseline CRISPS-1 (1995-1996). The optimal HOMA-IR cut-offs for dysglycemia and T2DM were determined by the receiver-operating characteristic (ROC) curve. Part two was a prospective study involving 872 subjects who had persistent NGT at CRISPS-4 (2010-2012) after 15 years of follow-up. At baseline, the optimal HOMA-IR cut-offs to identify dysglyceia and T2DM were 1.37 (AUC = 0.735; 95% confidence interval [CI] = 0.713-0.758; Sensitivity [Se] = 65.6%, Specificity [Sp] = 71.3%] and 1.97 (AUC = 0.807; 95% CI = 0.777-0.886; Se = 65.5%, Sp = 82.9%) respectively. These cut-offs, derived from the cross-sectional study at baseline, corresponded closely to the 75th (1.44) and 90th (2.03) percentiles, respectively, of the HOMA-IR reference range derived from the prospective study of subjects with persistent NGT. HOMA-IR cut-offs, of 1.4 and 2.0, which discriminated dysglycemia and T2DM respectively from NGT in Southern Chinese, can be usefully employed as references in clinical research involving the assessment of insulin resistance.

Practical side of cutting. Part 3. ; CO2 laser cutting. Setsudan gijutsu no jissai. 3. ; Laser setsudan

Energy Technology Data Exchange (ETDEWEB)

Miyazaki, T.; Shinonaga, H. (Toshiba Corp., Tokyo (Japan))

1993-03-05

The nature peculiar to laser beam makes it difficult to understand the phenomena in laser cutting. Quoting an example of cutting steel materials, practical minimum basic subjects, factors governing the cutting phenomena with points to be considered, and the current state of the technology are outlined. Various kinds of expert systems and automatic programming devices have been placed on the market to make NC input easier in laser cutting. Shape accuracy, cutting quality, cutting speed, applicable plate thickness, etc. are among the subjects required for laser cutting. The factors are the method of scanning, characteristics of laser beam, work, machining conditions, etc. The factors obstructing stable processing are the change in the ambient temperature, humidity, dust, oil mist, vibration, etc. The basic factors which control the laser cutting are the power density and its distribution at the working point. Pulse cutting is employed when continuous laser heat input is not appropriate. Summarized report is made on the focal point and assist gas. 16 refs., 9 figs., 1 tab.

Electrical Methods: Resistivity Methods

Science.gov (United States)

Surface electrical resistivity surveying is based on the principle that the distribution of electrical potential in the ground around a current-carrying electrode depends on the electrical resistivities and distribution of the surrounding soils and rocks.

Method for Friction Force Estimation on the Flank of Cutting Tools

Directory of Open Access Journals (Sweden)

Luis Huerta

2017-01-01

Full Text Available Friction forces are present in any machining process. These forces could play an important role in the dynamics of the system. In the cutting process, friction is mainly present in the rake face and the flank of the tool. Although the one that acts on the rake face has a major influence, the other one can become also important and could take part in the stability of the system. In this work, experimental identification of the friction on the flank is presented. The experimental determination was carried out by machining aluminum samples in a CNC lathe. As a result, two friction functions were obtained as a function of the cutting speed and the relative motion of the contact elements. Experiments using a worn and a new insert were carried out. Force and acceleration were recorded simultaneously and, from these results, different friction levels were observed depending on the cutting parameters, such as cutting speed, feed rate, and tool condition. Finally, a friction model for the flank friction is presented.

Automatic NC-Data generation method for 5-axis cutting of turbine-blades by finding Safe heel-angles and adaptive path-intervals

International Nuclear Information System (INIS)

Piao, Cheng Dao; Lee, Cheol Soo; Cho, Kyu Zong; Park, Gwang Ryeol

2004-01-01

In this paper, an efficient method for generating 5-axis cutting data for a turbine blade is presented. The interference elimination of 5-axis cutting currently is very complicated, and it takes up a lot of time. The proposed method can generate an interference-free tool path, within an allowance range. Generating the cutting data just point to the cutting process and using it to obtain NC data by calculating the feed rate, allows us to maintain the proper feed rate of the 5-axis machine. This paper includes the algorithms for: (1) CL data generation by detecting an interference-free heel angle, (2) finding the optimal tool path interval considering the cusp-height, (3) finding the adaptive feed rate values for each cutter path, and (4) the inverse kinematics depending on the structure of the 5-axis machine, for generating the NC data

Reliability analysis for thermal cutting method based non-explosive separation device

International Nuclear Information System (INIS)

Choi, Jun Woo; Hwang, Kuk Ha; Kim, Byung Kyu

2016-01-01

In order to increase the reliability of a separation device for a small satellite, a new non-explosive separation device is invented. This device is activated using a thermal cutting method with a Ni-Cr wire. A reliability analysis is carried out for the proposed non-explosive separation device by applying the Fault tree analysis (FTA) method. In the FTA results for the separation device, only ten single-point failure modes are found. The reliability modeling and analysis for the device are performed considering failure of the power supply, the Ni-Cr wire burns failure and unwinds, the holder separation failure, the balls separation failure, and the pin release failure. Ultimately, the reliability of the proposed device is calculated as 0.999989 with five Ni-Cr wire coils

Reliability analysis for thermal cutting method based non-explosive separation device

Energy Technology Data Exchange (ETDEWEB)

Choi, Jun Woo; Hwang, Kuk Ha; Kim, Byung Kyu [Korea Aerospace University, Goyang (Korea, Republic of)

2016-12-15

In order to increase the reliability of a separation device for a small satellite, a new non-explosive separation device is invented. This device is activated using a thermal cutting method with a Ni-Cr wire. A reliability analysis is carried out for the proposed non-explosive separation device by applying the Fault tree analysis (FTA) method. In the FTA results for the separation device, only ten single-point failure modes are found. The reliability modeling and analysis for the device are performed considering failure of the power supply, the Ni-Cr wire burns failure and unwinds, the holder separation failure, the balls separation failure, and the pin release failure. Ultimately, the reliability of the proposed device is calculated as 0.999989 with five Ni-Cr wire coils.

Methods and Research for Multi-Component Cutting Force Sensing Devices and Approaches in Machining

Directory of Open Access Journals (Sweden)

Qiaokang Liang

2016-11-01

Full Text Available Multi-component cutting force sensing systems in manufacturing processes applied to cutting tools are gradually becoming the most significant monitoring indicator. Their signals have been extensively applied to evaluate the machinability of workpiece materials, predict cutter breakage, estimate cutting tool wear, control machine tool chatter, determine stable machining parameters, and improve surface finish. Robust and effective sensing systems with capability of monitoring the cutting force in machine operations in real time are crucial for realizing the full potential of cutting capabilities of computer numerically controlled (CNC tools. The main objective of this paper is to present a brief review of the existing achievements in the field of multi-component cutting force sensing systems in modern manufacturing.

Methods and Research for Multi-Component Cutting Force Sensing Devices and Approaches in Machining.

Science.gov (United States)

Liang, Qiaokang; Zhang, Dan; Wu, Wanneng; Zou, Kunlin

2016-11-16

Multi-component cutting force sensing systems in manufacturing processes applied to cutting tools are gradually becoming the most significant monitoring indicator. Their signals have been extensively applied to evaluate the machinability of workpiece materials, predict cutter breakage, estimate cutting tool wear, control machine tool chatter, determine stable machining parameters, and improve surface finish. Robust and effective sensing systems with capability of monitoring the cutting force in machine operations in real time are crucial for realizing the full potential of cutting capabilities of computer numerically controlled (CNC) tools. The main objective of this paper is to present a brief review of the existing achievements in the field of multi-component cutting force sensing systems in modern manufacturing.

Laser beam cutting method. Laser ko ni yoru kaitai koho

Energy Technology Data Exchange (ETDEWEB)

Kutsumizu, A. (Obayashi Corp., Osaka (Japan))

1991-07-01

In this special issue paper concerning the demolition of concrete structures, was introduced a demolition of concrete structures using laser, of which practical application is expected due to the remarkable progress of generating power and efficiency of laser radiator. The characteristics of laser beam which can give a temperature of one million centigrade at the irradiated spot, the laser radiator consisting of laser medium, laser resonator and pumping apparatus, and the laser kinds for working, such as CO{sub 2} laser, YAG laser and CO laser, were described. The basic constitution of laser cutting equipment consisting of large generating power radiator, beam transmitter, beam condenser, and nozzle for working was also illustrated. Furthermore, strong and weak points in the laser cutting for concrete and reinforcement were enumerated. Applications of laser to cutting of reinforced and unreinforced concrete constructions were shown, and the concept and safety measure for application of laser to practical demolition was discussed. 5 refs., 8 figs.

A study of insulin resistance by HOMA-IR and its cut-off value to identify metabolic syndrome in urban Indian adolescents.

Science.gov (United States)

Singh, Yashpal; Garg, M K; Tandon, Nikhil; Marwaha, Raman Kumar

2013-01-01

Insulin resistance (IR) and associated metabolic abnormalities are increasingly being reported in the adolescent population. Cut-off value of homeostasis model of assessment IR (HOMA-IR) as an indicator of metabolic syndrome (MS) in adolescents has not been established. This study aimed to investigate IR by HOMA-IR in urban Indian adolescents and to establish cut-off values of HOMA-IR for defining MS. A total of 691 apparently healthy adolescents (295 with normal body mass index (BMI), 205 overweight, and 199 obese) were included in this cross-sectional study. MS in adolescents was defined by International Diabetes Federation (IDF) and Adult Treatment Panel III (ATP III) criteria. IR was calculated using the HOMA model. Mean height, waist circumference (WC), waist/hip ratio (WHR), waist/height ratio (WHtR), and blood pressure were significantly higher in boys as compared to girls. The HOMA-IR values increased progressively from normal weight to obese adolescents in both sexes. Mean HOMA-IR values increased progressively according to sexual maturity rating in both sexes. HOMA-IR value of 2.5 had a sensitivity of >70% and specificity of >60% for MS. This cut-off identified larger number of adolescents with MS in different BMI categories (19.7% in normal weight, 51.7% in overweight, and 77.0% in obese subjects) as compared to the use of IDF or ATP III criteria for diagnosing MS. Odds ratio for having IR (HOMA-IR of >2.5) was highest with WHtR (4.9, p pHOMA-IR increased with sexual maturity and with progression from normal to obese. A HOMA-IR cut-off of 2.5 provided the maximum sensitivity and specificity in diagnosing MS in both genders as per ATP III and IDF criteria.

Improved cutting performance in high power laser cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove

2003-01-01

Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described.......Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described....

Fabricating 40 µm-thin silicon solar cells with different orientations by using SLiM-cut method

Science.gov (United States)

Wang, Teng-Yu; Chen, Chien-Hsun; Shiao, Jui-Chung; Chen, Sung-Yu; Du, Chen-Hsun

2017-10-01

Thin silicon foils with different crystal orientations were fabricated using the stress induced lift-off (SLiM-cut) method. The thickness of the silicon foils was approximately 40 µm. The ≤ft foil had a smoother surface than the ≤ft foil. With surface passivation, the minority carrier lifetimes of the ≤ft and ≤ft silicon foil were 1.0 µs and 1.6 µs, respectively. In this study, 4 cm2-thin silicon solar cells with heterojunction structures were fabricated. The energy conversion efficiencies were determined to be 10.74% and 14.74% for the ≤ft and ≤ft solar cells, respectively. The surface quality of the silicon foils was determined to affect the solar cell character. This study demonstrated that fabricating the solar cell by using silicon foil obtained from the SLiM-cut method is feasible.

A Numerical Approach and Comparison of Cutting Forces and Chip Morphology in Orthogonal Cutting of Light Alloys

International Nuclear Information System (INIS)

Alvarez, Roberto; Domingo, Rosario; Sebastian, Miguel Angel

2011-01-01

This paper deals with the simulation of UNS A92024 aluminium alloy cutting processes. In particular, 2D and 3D Finite Element Method (FEM) simulations were carried out in order to estimate cutting forces and chip morphology during turning operations. The material is modelled with two different set of parameters for the Johnson--Cook's (J-C) constitutive equation and a failure Cockroft and Latham's model exploited considers damage. The comparison between the predicted chip morphology and principal cutting forces at varying of J-C parameters and cutting regimes with those experimentally found are presented and discussed. The paper shows the importance of damage criterion in the cutting forces, during the simulation, especially in 3D.

Mechanisms and FEM Simulation of Chip Formation in Orthogonal Cutting In-Situ TiB₂/7050Al MMC.

Science.gov (United States)

Xiong, Yifeng; Wang, Wenhu; Jiang, Ruisong; Lin, Kunyang; Shao, Mingwei

2018-04-15

The in-situ TiB₂/7050Al composite is a new kind of Al-based metal matrix composite (MMC) with super properties, such as low density, improved strength, and wear resistance. This paper, for a deep insight into its cutting performance, involves a study of the chip formation process and finite element simulation during orthogonal cutting in-situ TiB₂/7050Al MMC. With chips, material properties, cutting forces, and tool geometry parameters, the Johnson-Cook (J-C) constitutive equation of in-situ TiB₂/7050Al composite was established. Then, the cutting simulation model was established by applying the Abaqus-Explicit method, and the serrated chip, shear plane, strain rate, and temperature were analyzed. The experimental and simulation results showed that the obtained material's constitutive equation was of high reliability, and the saw-tooth chips occurred commonly under either low or high cutting speed and small or large feed rate. From result analysis, it was found that the mechanisms of chip formation included plastic deformation, adiabatic shear, shearing slip, and crack extension. In addition, it was found that the existence of small, hard particles reduced the ductility of the MMC and resulted in segmental chips.

Insulin Resistance Distribution and Cut-Off Value in Koreans from the 2008-2010 Korean National Health and Nutrition Examination Survey

Science.gov (United States)

Yun, Kyung-Jin; Han, Kyungdo; Kim, Mee Kyoung; Park, Yong-Moon; Baek, Ki-Hyun; Song, Ki-Ho; Kwon, Hyuk-Sang

2016-01-01

Background We sought to identify the distribution and cut-off value of the ‘homeostasis model assessment of insulin resistance’ (HOMA-IR) according to gender and menopausal status for metabolic syndrome in Koreans. Methods Data were from the Korean National Health and Nutrition Examination Survey in 2008–2010. The subjects included adults aged 20 years or older. We excluded participants who had diabetes or fasting serum glucose ≥ 7 mmol/L. Finally, 11,121 subjects (4,911 men, 3,597 premenopausal women, 2,613 postmenopausal women) were enrolled. The modified Adult Treatment Panel III criteria were used to define metabolic syndrome. Results The mean HOMA-IR was 2.11 (2.07–2.15) for men, 2.0 (1.97–2.04) for premenopausal women, and 2.14 (2.2–2.19) for postmenopausal women. The first cut-off values in men, premenopausal women, and postmenopausal women were 2.23 (sensitivity 70.6%, specificity 66.9%), 2.39 (sensitivity 72.3%, specificity 76.4%), and 2.48 (sensitivity 51.9%, specificity 80.2%), respectively. Based on the first HOMA-IR cut-off value, the prevalence of metabolic syndrome was 22.9% in men, 13.7% in premenopausal women, and 51.6% in postmenopausal women. The second cut-off value was around 3.2 in all three groups. Based on the second HOMA-IR cut-off value, the prevalence of metabolic syndrome was 50.8% in men, 42.5% in premenopausal women, and 71.6% in postmenopausal women. Conclusion In conclusion, the first cut-off values for HOMA-IR were 2.2–2.5 and the second cut-off value was 3.2 in Korea. The distribution of HOMA-IR showed differences according to gender and menopausal status. When we apply HOMA-IR, we should consider gender, menopausal status, and the prevalence of metabolic syndrome. PMID:27128847

Short-cut math

CERN Document Server

Kelly, Gerard W

1984-01-01

Clear, concise compendium of about 150 time-saving math short-cuts features faster, easier ways to add, subtract, multiply, and divide. Each problem includes an explanation of the method. No special math ability needed.

Molecular detection methods of resistance to antituberculosis drugs in Mycobacterium tuberculosis.

Science.gov (United States)

Brossier, F; Sougakoff, W

2017-09-01

Molecular methods predict drug resistance several weeks before phenotypic methods and enable rapid implementation of appropriate therapeutic treatment. We aimed to detail the most representative molecular tools used in routine practice for the rapid detection of resistance to antituberculosis drugs among Mycobacterium tuberculosis strains. The molecular diagnosis of resistance to antituberculosis drugs in clinical samples or from in vitro cultures is based on the detection of the most common mutations in the genes involved in the development of resistance in M. tuberculosis strains (encoding either protein targets of antibiotics, or antibiotic activating enzymes) by commercial molecular kits or by sequencing. Three hypotheses could explain the discrepancies between the genotypic results and the phenotypic drug susceptibility testing results: a low percentage of resistant mutants precluding the detection by genotypic methods on the primary culture; a low level of resistance not detected by phenotypic testing; and other resistance mechanisms not yet characterized. Molecular methods have varying sensitivity with regards to detecting antituberculosis drug resistance; that is why phenotypic susceptibility testing methods are mandatory for detecting antituberculosis drug-resistant isolates that have not been detected by molecular methods. The questionable ability of existing phenotypic and genotypic drug susceptibility testing to properly classify strains as susceptible or resistant, and at what level of resistance, was raised for several antituberculosis agents. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Experimental study on concrete cutting by CO2 laser beam

International Nuclear Information System (INIS)

Kutsumizu, Akira; Tomura, Hidemasa; Wakizaka, Tatsuya; Hishikawa, Kyoichi; Moriya, Masahiro

1994-01-01

Methods for dismantling nuclear reactor facilities must meet particularly exacting requirements imposed by heavily reinforced and radioactivated reactor shield walls. Conventional methods do not meet all such requirements, however. Intrigued by excellent characteristics of the laser cutting method relative to nuclear facility demolition, we carried out an experimental study to make a comprehensive evaluation of its characteristics, especially for deep cutting, with success in identifying main factors affecting the cutting depth of a laser and characterizing its cutting behavior. The study results indicate that a 50 kW class CO 2 laser has a potential to provide a practicable cutting speed and depth. (author)

Effects of reinforcement without extinction on increasing compliance with nail cutting: A systematic replication.

Science.gov (United States)

Dowdy, Art; Tincani, Matt; Nipe, Timothy; Weiss, Mary Jane

2018-06-17

Personal hygiene routines, such as nail cutting, are essential for maintaining good health. However, individuals with autism spectrum disorder (ASD) and other developmental disabilities often struggle to comply with essential, personal hygiene routines. We conducted a systematic replication of Schumacher and Rapp (2011), Shabani and Fisher (2006), and Bishop et al. (2013) to evaluate an intervention that did not require escape extinction for increasing compliance with nail cutting. With two adolescents diagnosed with ASD who resisted nail cutting, we evaluated the effects of delivering a preferred edible item contingent on compliance with nail cutting. Results indicated that the treatment reduced participants' escape responses and increased their compliance with nail cutting. © 2018 Society for the Experimental Analysis of Behavior.

Features of energy impact on a billet material when cutting with outstripping plastic deformation

Directory of Open Access Journals (Sweden)

V. M. Yaroslavtsev

2014-01-01

cases. At the same time, when cutting with OPD, a part of the work spent on plastic deformations, is preliminary carried out by an additional mechanical energy source, i.e. by the device for superficial plastic deformation of material. As a result the cutting tool makes only the rest of the work that can facilitate to decrease of cutting force and temperature. The cutting force and temperature define a stress of machining process. Reduction of these parameters when cutting with OPD allows us to rise the resistance period of the cutting tool (up to 2–6 times and the workforce productivity (up to 1,1–1,6 times depending on physic-mechanical properties of processed material.However, the maximum efficiency of additional mechanical influence is reached only when there is the optimum relationship between the specific energy of superficial material deformation of a cut-off layer and chip formation process while cutting. Experimental data show that at small specific loads of preliminary material deformation an increase of these loads leads to the increase of a part of additional energy during the cut-off layer removal that enables efficiency increase of cutting process with OPD. At the same time, with increasing extent of preliminary plastic deformation of removable material the microhardness of a cut-off layer increases. It has a negative impact on the interaction conditions of tool contact surfaces with a billet material, increases the stress of cutting process, leads to decrease of technical-andeconomic indicators of machining. As a result at the raised specific loads of preliminary deformation negative factors become prevailing and cause, at first, decreasing process efficiency. The further increase of deformation work leads to a negative effect of additional OPD energy influence.Thus, an influence efficiency of additional external energies in the combined methods of machining depends on many factors, and the result of such impact on the billet can change over a wide

The Use of Resistivity Methods in Terrestrial Forensic Searches

Science.gov (United States)

Wolf, R. C.; Raisuddin, I.; Bank, C.

2013-12-01

The increasing use of near-surface geophysical methods in forensic searches has demonstrated the need for further studies to identify the ideal physical, environmental and temporal settings for each geophysical method. Previous studies using resistivity methods have shown promising results, but additional work is required to more accurately interpret and analyze survey findings. The Ontario Provincial Police's UCRT (Urban Search and Rescue; Chemical, Biolgical, Radiological, Nuclear and Explosives; Response Team) is collaborating with the University of Toronto and two additional universities in a multi-year study investigating the applications of near-surface geophysical methods to terrestrial forensic searches. In the summer of 2012, on a test site near Bolton, Ontario, the OPP buried weapons, drums and pigs (naked, tarped, and clothed) to simulate clandestine graves and caches. Our study aims to conduct repeat surveys using an IRIS Syscal Junior with 48 electrode switching system resistivity-meter. These surveys will monitor changes in resistivity reflecting decomposition of the object since burial, and identify the strengths and weaknesses of resistivity when used in a rural, clandestine burial setting. Our initial findings indicate the usefulness of this method, as prominent resistivity changes have been observed. We anticipate our results will help to assist law enforcement agencies in determining the type of resistivity results to expect based on time since burial, depth of burial and state of dress of the body.

Development and verification test on remote plasma cutting of large metallic waste

International Nuclear Information System (INIS)

Ozawa, Tamotsu; Yamada, Kunitaka; Abe, Tadashi

1979-01-01

Plasma cutting is the cutting method to melt and scatter cut objects by generating arc between an electrode in a nozzle and the cut objects and making working gas fed to surround it into high temperature, high speed plasma jet. In case of remote plasma cutting, a torch for the plasma cutting is operated remotely with a manipulator from the outside of a cell. At the time of planning the method of breaking up solid wastes, the type of cutting machines and the method of remote operation of the cutting machines and cut objects were examined. It was decided to adopt plasma cutting machines, because their cutting capability such as materials, thickness and cutting speed is excellent, and the construction and handling are simple. The form of the solid wastes to be cut is not uniform, accordingly the method of manipulator operation was adopted to respond to various forms flexibly. Cut objects are placed on a turntable to change the position successively. In case of remote plasma cutting, the controls of torch speed and gap must be made with a manipulator. The use of light-shielding glasses reduces largely the watchability of cut objects and becomes hindrance in the operation. As for the safety aspect, the suitable gas for cutting, which does not contain hydrogen, must be selected. The tests carried out for two years since November, 1977, are reported in this paper, and most of the problems have been solved. (Kako, I.)

Using a cut-paste method to prepare a carbon nanotube fur electrode

International Nuclear Information System (INIS)

Zhang, H; Cao, G P; Yang, Y S

2007-01-01

We describe and realize an aligned carbon nanotube array based 'carbon nanotube fur (CNTF)' electrode. We removed an 800 μm long aligned carbon nanotube array from the silica substrate, and then pasted the array on a nickel foam current collector to obtain a CNTF electrode. CNTF's characteristics and electrochemical properties were studied systemically in this paper. The cut-paste method is simple, and does not damage the microstructure of the aligned carbon nanotube array. The CNTF electrode obtained a specific capacitance of 14.1 F g -1 and excellent rate capability

Laser cutting of Kevlar laminates

Energy Technology Data Exchange (ETDEWEB)

VanCleave, R.A.

1977-09-01

An investigation has been conducted of the use of laser energy for cutting contours, diameters, and holes in flat and shaped Kevlar 49 fiber-reinforced epoxy laminates as an alternate to conventional machining. The investigation has shown that flat laminates 6.35 mm thick may be cut without backup by using a high-powered (1000-watt) continuous wave CO/sub 2/ laser at high feedrates (33.87 mm per second). The cut produced was free of the burrs and delaminations resulting from conventional machining methods without intimate contact backup. In addition, the process cycle time was greatly reduced.

Propagation by Cuttings, Layering and Division

OpenAIRE

Relf, Diane; Ball, Elizabeth Carter

2009-01-01

The major methods of asexual propagation are cuttings, layering, division, and budding/grafting. Cuttings involve rooting a severed piece of the parent plant; layering involves rooting a part of the parent and then severing it; and budding and grafting are joining two plant parts from different varieties.

Exploitation study of the ore-body ''Tigre III''. Open-cut design and study of high-recovery underground mining method for the Tigre III ore-body

International Nuclear Information System (INIS)

Baluszka, J.C.

1980-01-01

The paper first carries out an analysis for the purpose of determining the limiting sterile/ore ratio for open-cut and underground mining in the specific filling case of Tigre III. In this connection it considers a high-recovery method of underground mining (involving the use of cemented hydropneumatic chambers), a general mine plan covering access, transport, ventilation and removal of ore as well as auxiliary services relating to the Tigre III ore body as a whole. The costs of this method of mining are determined for purposes of comparison with the open-cut method. Similarly, the limiting sterile/ore ratio is taken as the basis for an analysis of different types of pit and a design suited to the limiting ratio is adopted. As a final solution the paper favours a method which combines open-cut and underground mining. It proposes the use of the open-cut method up to the limiting ratio (in accordance with the pit design chosen) and of underground method (by the filling chamber method) for the rest of the area. (author)

A Study on Ultrasonic Elliptical Vibration Cutting of Inconel 718

Directory of Open Access Journals (Sweden)

Zhao Haidong

2016-01-01

Full Text Available Inconel 718 is a kind of nickel-based alloys that are widely used in the aerospace and nuclear industry owing to their high temperature mechanical properties. Cutting of Inconel 718 in conventional cutting (CC is a big challenge in modern industry. Few researches have been studied on cutting of Inconel 718 using single point diamond tool applying the UEVC method. This paper shows an experimental study on UEVC of Inconel 718 by using polycrystalline diamond (PCD coated tools. Firstly, cutting tests have been carried out to study the effect of machining parameters in the UEVC in terms of surface finish and flank wear during machining of Inconel 718. The tests have clearly shown that the PCD coated tools in cutting of Inconel 718 by the UEVC have better performance at 0.1 mm depth of cut as compared to the lower 0.05 mm depth of cut and the higher 0.12 or 0.15 mm depth of cut. Secondly, like CC method, the cutting performance in UEVC increases with the decrease of the feed rate and cutting speed. The CC tests have also been carried out to compare performance of CC with UEVC method.

Gear cutting tools fundamentals of design and computation

CERN Document Server

Radzevich, Stephen P

2010-01-01

Presents the DG/K-based method of surface generation, a novel and practical mathematical method for designing gear cutting tools with optimal parameters. This book proposes a scientific classification for the various kinds of the gear machining meshes, discussing optimal designs of gear cutting tools.

Baikov-Lee representations of cut Feynman integrals

International Nuclear Information System (INIS)

Harley, Mark; Moriello, Francesco; Schabinger, Robert M.

2017-01-01

We develop a general framework for the evaluation of d-dimensional cut Feynman integrals based on the Baikov-Lee representation of purely-virtual Feynman integrals. We implement the generalized Cutkosky cutting rule using Cauchy’s residue theorem and identify a set of constraints which determine the integration domain. The method applies equally well to Feynman integrals with a unitarity cut in a single kinematic channel and to maximally-cut Feynman integrals. Our cut Baikov-Lee representation reproduces the expected relation between cuts and discontinuities in a given kinematic channel and furthermore makes the dependence on the kinematic variables manifest from the beginning. By combining the Baikov-Lee representation of maximally-cut Feynman integrals and the properties of periods of algebraic curves, we are able to obtain complete solution sets for the homogeneous differential equations satisfied by Feynman integrals which go beyond multiple polylogarithms. We apply our formalism to the direct evaluation of a number of interesting cut Feynman integrals.

Resistivity measurements using a direct current induction method (1963); Mesure de resistivite par la methode d'induction en courant continu (1963)

Energy Technology Data Exchange (ETDEWEB)

Delaplace, J; Hillairet, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

The conventional methods for measuring electrical resistivities necessitate the fixing of electrical contacts on the sample either mechanically or by soldering. Furthermore it is also necessary to carry,out the measurements on low cross-section samples which are not always easy to obtain. Our direct-current induction method on the other hand requires no contacts and can easily be applied to samples of large cross-section. The sample is placed in a uniform magnetic field; at the moment when the current is cut, eddy currents appear in the sample which tend to oppose the disappearance of the field. The way in which the magnetic flux decreases in the sample makes it possible to determine the resistivity of the material. This method has been applied to samples having diameters of between 1 and 30 mm in the case of metals which are good conductors. It gives a value for the local resistivity and makes it possible to detect any variation along a sample. The measurements can be carried out at all temperature from a few degrees absolute to 500 deg. C. We have used the induction method to follow the purification of beryllium by zone-melting; it is in effect possible to estimate the purity of a material by resistivity measurements. We have measured the resistivity along each bar treated by the zone-melting technique and have thus, localised the purest section. High temperature measurements have been carried out on uranium carbide and on iron-aluminium alloys. This method constitutes an interesting means of investigation the resistivity of solid materials. Its accuracy and rapidity make it particularly adapted both to fundamental research and to production control. (authors) [French] Les methodes classiques de mesure de resistivite electrique imposent la realisation sur l'echantillon de contacts electriques obtenus soit mecaniquement, soit par soudure. En outre, elles demandent, le plus souvent, d'effectuer les mesures sur des echantillons de faible section qu'il n'est pas

Wear Mechanism of Chemical Vapor Deposition (CVD) Carbide Insert in Orthogonal Cutting Ti-6Al-4V ELI at High Cutting Speed

International Nuclear Information System (INIS)

Gusri, A. I.; Che Hassan, C. H.; Jaharah, A. G.

2011-01-01

The performance of Chemical Vapor Deposition (CVD) carbide insert with ISO designation of CCMT 12 04 04 LF, when turning titanium alloys was investigated. There were four layers of coating materials for this insert i.e.TiN-Al2O3-TiCN-TiN. The insert performance was evaluated based on the insert's edge resistant towards the machining parameters used at high cutting speed range of machining Ti-6Al-4V ELI. Detailed study on the wear mechanism at the cutting edge of CVD carbide tools was carried out at cutting speed of 55-95 m/min, feed rate of 0.15-0.35 mm/rev and depth of cut of 0.10-0.20 mm. Wear mechanisms such as abrasive and adhesive were observed on the flank face. Crater wear due to diffusion was also observed on the rake race. The abrasive wear occurred more at nose radius and the fracture on tool were found at the feed rate of 0.35 mm/rev and the depth of cut of 0.20 mm. The adhesion wear takes place after the removal of the coating or coating delaminating. Therefore, adhesion or welding of titanium alloy onto the flank and rake faces demonstrates a strong bond at the workpiece-tool interface.

29 CFR 1910.255 - Resistance welding.

Science.gov (United States)

2010-07-01

... 29 Labor 5 2010-07-01 2010-07-01 false Resistance welding. 1910.255 Section 1910.255 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Welding, Cutting and Brazing § 1910.255 Resistance welding. (a.... Ignitron tubes used in resistance welding equipment shall be equipped with a thermal protection switch. (3...

Drilling of metal matrix composites: cutting forces and chip formation

International Nuclear Information System (INIS)

Songmene, V.; Balout, B.; Masounave, J.

2002-01-01

Particulate metal matrix composites (MMCs) are known for their low weight and their high wear resistance, but also for the difficulties encountered during their machining. New aluminium MMCs containing with both soft lubricating graphite particles and hard particles (silicon carbide or alumina) with improved machinability were developed. This study investigates the drilling of these composites as compared to non-reinforced aluminium. The microstructure of chip, the cutting forces, the shear angles and the friction at tool-chip interface are used to compare the machinability of these composites. It was found that, during drilling of this new family of composites, the feed rate, and the nature of reinforcing particles govern the cutting forces. The mathematical models established by previous researchers for predicting the cutting forces when drilling metals were validated for these composites. The reinforcing particles within the composite help for chip segmentation, making the composite more brittle and easy to shear during the cutting process. (author)

Fibre laser cutting stainless steel: Fluid dynamics and cut front morphology

Science.gov (United States)

Pocorni, Jetro; Powell, John; Deichsel, Eckard; Frostevarg, Jan; Kaplan, Alexander F. H.

2017-01-01

In this paper the morphology of the laser cut front generated by fibre lasers was investigated by observation of the 'frozen' cut front, additionally high speed imaging (HSI) was employed to study the fluid dynamics on the cut front while cutting. During laser cutting the morphology and flow properties of the melt film on the cut front affect cut quality parameters such as cut edge roughness and dross (residual melt attached to the bottom of the cut edge). HSI observation of melt flow down a laser cutting front using standard cutting parameters is experimentally problematic because the cut front is narrow and surrounded by the kerf walls. To compensate for this, artificial parameters are usually chosen to obtain wide cut fronts which are unrepresentative of the actual industrial process. This paper presents a new experimental cutting geometry which permits HSI of the laser cut front using standard, commercial parameters. These results suggest that the cut front produced when cutting medium section (10 mm thick) stainless steel with a fibre laser and a nitrogen assist gas is covered in humps which themselves are covered by a thin layer of liquid. HSI observation and theoretical analysis reveal that under these conditions the humps move down the cut front at an average speed of approximately 0.4 m/s while the covering liquid flows at an average speed of approximately 1.1 m/s, with an average melt depth at the bottom of the cut zone of approximately 0.17 mm.

A study on the mechanical behavior of soils during flat edge cutting

International Nuclear Information System (INIS)

Ichiba, Satoru; Hyodo, Kazuya; Ooishi, Yoshihiro

1986-01-01

For the development of efficient earthmoving machinery, it is necessary to clarify the soil cutting mechanism, but there is no usual analytical or experimental technique for large deformation problems like soil cutting. Therefore, we have tried to apply the X-ray radiography method, which is a soil experiment method for the visualization and the quantative analysis of soil deformation, to the flat edge cutting problem. Firstly we have confirmed that the X-ray radiography method is applicable to large deformations, and have examined by this method the cutting mechanism of soils under various cutting conditions. As a result, the behavior of shear failure lines, which have not been studied in detail before, are clarified, and the differences in the cutting mechanism with the cutting angle and the nature of soils are discussed through the quantative estimation of the strain distribution. (author)

A study on the mechanical behavior of soil during frat edge cutting

International Nuclear Information System (INIS)

Ichiba, Satoru; Hyodo, Kazuya; Ooishi, Yoshihiro.

1987-02-01

For the development of efficient earthmoving machinery, it is necessary to clarify the soil cutting mechanism, but there is no usual analytical or experimental technique for large deformation problems like soil cutting. Therefore, we have tried to apply the X-ray radiography method, which is a soil experiment method for the visualization and the quantitative analysis of soil deformation, to the flat edge cutting problem. Firstly we have confirmed that the X-ray radiography method is applicable to large deformations, and have examined by this method the cutting mechanism of soils under various cutting conditions. As a result, the behavior of shear failure lines, which have not been studied in detail before, are clarified, and the differences in the cutting mechanism with the cutting angle and the nature of soils are discussed through the quantitative estimation of the strain distribution. (author)

Accuracy of unfolded map method for determining the left ventricular border. Evaluation of the cut-off value from autopsy finding

International Nuclear Information System (INIS)

Sugibayashi, Keiichi; Abe, Yoshiteru; Suga, Yutaka

1996-01-01

To improve the quantification of the left ventricular surface area (LVSA) by unfolded map method, we evaluated the cut-off value for determining the left ventricular border. The LVSA measured by unfolded map was compared with those measured using myocardial phantom and autopsy findings. The relative error (RE) was calculated as difference between LVSA in phantom and area of unfolded map. In phantom study, the cut-off value was calculated as 73.3±0.5% when the RE was zero. In autopsy study, the cut-off value was 74.0±7.2%. The area of unfolded map had good correlation with LVSA at autopsy when the cut-off value was 74% (r=0.83, p<0.003). The diameter of left ventricle at autopsy was compared with that of beating heart obtained by two-dimensional echocardiography, because the area of unfolded map was greater than LVSA at autopsy. The ratio of LVSA at autopsy to beating heart was calculated as 1.37. The suitable cut-off value was evaluated as 55.6% when the unfolded map area obtained by autopsy was increased 1.37 magnifications. There was a good correlation between LVSA of unfolded map (cut-off=56%) and the LVSA at autopsy (r=0.90, p<0.001). These results suggest that the cut-off value for determining the left ventricular border in vivo is 56%. (author)

Experimental study on concrete cutting by CO{sub 2} laser beam

Energy Technology Data Exchange (ETDEWEB)

Kutsumizu, Akira; Tomura, Hidemasa; Wakizaka, Tatsuya; Hishikawa, Kyoichi; Moriya, Masahiro [Ohbayashi Corp., Tokyo (Japan)

1994-10-01

Methods for dismantling nuclear reactor facilities must meet particularly exacting requirements imposed by heavily reinforced and radioactivated reactor shield walls. Conventional methods do not meet all such requirements, however. Intrigued by excellent characteristics of the laser cutting method relative to nuclear facility demolition, we carried out an experimental study to make a comprehensive evaluation of its characteristics, especially for deep cutting, with success in identifying main factors affecting the cutting depth of a laser and characterizing its cutting behavior. The study results indicate that a 50 kW class CO{sub 2} laser has a potential to provide a practicable cutting speed and depth. (author).

MULTI-OBJECTIVE OPTIMISATION OF LASER CUTTING USING CUCKOO SEARCH ALGORITHM

Directory of Open Access Journals (Sweden)

M. MADIĆ

2015-03-01

Full Text Available Determining of optimal laser cutting conditions for improving cut quality characteristics is of great importance in process planning. This paper presents multi-objective optimisation of the CO2 laser cutting process considering three cut quality characteristics such as surface roughness, heat affected zone (HAZ and kerf width. It combines an experimental design by using Taguchi’s method, modelling the relationships between the laser cutting factors (laser power, cutting speed, assist gas pressure and focus position and cut quality characteristics by artificial neural networks (ANNs, formulation of the multiobjective optimisation problem using weighting sum method, and solving it by the novel meta-heuristic cuckoo search algorithm (CSA. The objective is to obtain optimal cutting conditions dependent on the importance order of the cut quality characteristics for each of four different case studies presented in this paper. The case studies considered in this study are: minimisation of cut quality characteristics with equal priority, minimisation of cut quality characteristics with priority given to surface roughness, minimisation of cut quality characteristics with priority given to HAZ, and minimisation of cut quality characteristics with priority given to kerf width. The results indicate that the applied CSA for solving the multi-objective optimisation problem is effective, and that the proposed approach can be used for selecting the optimal laser cutting factors for specific production requirements.

Multidimensional Brain MRI segmentation using graph cuts

International Nuclear Information System (INIS)

Lecoeur, Jeremy

2010-01-01

This thesis deals with the segmentation of multimodal brain MRIs by graph cuts method. First, we propose a method that utilizes three MRI modalities by merging them. The border information given by the spectral gradient is then challenged by a region information, given by the seeds selected by the user, using a graph cut algorithm. Then, we propose three enhancements of this method. The first consists in finding an optimal spectral space because the spectral gradient is based on natural images and then inadequate for multimodal medical images. This results in a learning based segmentation method. We then explore the automation of the graph cut method. Here, the various pieces of information usually given by the user are inferred from a robust expectation-maximization algorithm. We show the performance of these two enhanced versions on multiple sclerosis lesions. Finally, we integrate atlases for the automatic segmentation of deep brain structures. These three new techniques show the adaptability of our method to various problems. Our different segmentation methods are better than most of nowadays techniques, speaking of computation time or segmentation accuracy. (authors)

Cutting state identification

International Nuclear Information System (INIS)

Berger, B.S.; Minis, I.; Rokni, M.

1997-01-01

Cutting states associated with the orthogonal cutting of stiff cylinders are identified through an analysis of the singular values of a Toeplitz matrix of third order cumulants of acceleration measurements. The ratio of the two pairs of largest singular values is shown to differentiate between light cutting, medium cutting, pre-chatter and chatter states. Sequences of cutting experiments were performed in which either depth of cut or turning frequency was varied. Two sequences of experiments with variable turning frequency and five with variable depth of cut, 42 cutting experiments in all, provided a database for the calculation of third order cumulants. Ratios of singular values of cumulant matrices find application in the analysis of control of orthogonal cutting

Method of vertically and horizontally cutting steel pipe piles and removing them based on the development of a steel pipe pile vertically cutting machine; Kokanko tatehoko setsudanki no kaihatsu ni yoru kochi chubu no juo setsudan tekkyo koho

Energy Technology Data Exchange (ETDEWEB)

Watanabe, S.; Takeshita, A.; Kobayashi, K.

1997-07-25

A machine for vertically cutting steel pipe piles has newly been developed for the purpose of removing the end portions the shore protection steel pipe piles which interfere with the shield tunneling work in the Ohokagawa River tunneling section on the Minato Mirai 21 Line. This paper reports the development of the machine for vertically cutting steel pipe piles, and a method of cutting the shield tunneling work hindering piles under the ground by using this machine. The obstacle-constituting portions of the piles are removed by destroying the copings, excavating the interior of the piles to make the same hollow so that a cutting machine can be inserted, and cutting the piles vertically and horizontally. The basic structure of the cutting machine comprises a lower cutting unit for making forward and backward and upward and downward movements of a cutter, and an upper movable unit for controlling the rotation of the cutting unit. The cutting of a pile is done by projecting the cutter by a cylinder the base of which is joined to a cutter driver, and then moving the rotating cutter upward. The amounts of movements of these parts are detected by sensors, and an arbitrary range of the underground portion of a pile can be cut by a remote control operation. 10 figs., 1 tab.

Resistivity Correction Factor for the Four-Probe Method: Experiment I

Science.gov (United States)

Yamashita, Masato; Yamaguchi, Shoji; Enjoji, Hideo

1988-05-01

Experimental verification of the theoretically derived resistivity correction factor (RCF) is presented. Resistivity and sheet resistance measurements by the four-probe method are made on three samples: isotropic graphite, ITO film and Au film. It is indicated that the RCF can correct the apparent variations of experimental data to yield reasonable resistivities and sheet resistances.

Influence of Cutting Fluid Flow Rate and Cutting Parameters on the Surface Roughness and Flank Wear of TiAlN Coated Tool In Turning AISI 1015 Steel Using Taguchi Method

Directory of Open Access Journals (Sweden)

Moganapriya C.

2017-09-01

Full Text Available This paper presents the influence of cutting parameters (Depth of cut, feed rate, spindle speed and cutting fluid flow rate on the surface roughness and flank wear of physical vapor deposition (PVD Cathodic arc evaporation coated TiAlN tungsten carbide cutting tool insert during CNC turning of AISI 1015 mild steel. Analysis of Variance has been applied to determine the critical influence of cutting parameters. Taguchi orthogonal test design has been employed to optimize the process parameters affecting surface roughness and tool wear. Depth of cut was found to be the most dominant factor contributing to high surface roughness (67.5% of the inserts. However, cutting speed, feed rate and flow rate of cutting fluid showed minimal contribution to surface roughness. On the other hand, cutting speed (45.6% and flow rate of cutting fluid (23% were the dominant factors influencing tool wear. The optimum cutting conditions for desired surface roughness constitutes the following parameters such as medium cutting speed, low feed rate, low depth of cut and high cutting fluid flow rate. Minimal tool wear was achieved for the following process parameters such as low cutting speed, low feed rate, medium depth of cut and high cutting fluid flow rate.

Experimental Investigation of Tensile Test on Connection of Cold-formed Cut-curved Steel Section

Science.gov (United States)

Sani, Mohd Syahrul Hisyam Mohd; Muftah, Fadhluhartini; Rahman, Nurul Farraheeda Abdul; Fakri Muda, Mohd

2017-08-01

Cold-formed steel (CFS) is widely used as structural and non-structural components such as roof trusses and purlin. A CFS channel section with double intermediate web stiffener and lipped is chosen based on the broader usage in roof truss construction. CFS section is cut to form cold-formed pre-cut-curved steel section and lastly strengthened by several types of method or likely known as connection to establish the cold-formed cut-curved steel (CFCCS) section. CFCCS is proposed to be used as a top chord section in the roof truss system. The CFCCS is to resist the buckling phenomena of the roof truss structure and reduced the compression effect on the top chord. The tensile test connection of CFCCS section, especially at the flange element with eight types of connection by welding, plate with self-drilling screw and combination is investigated. The flange element is the weakest part that must be solved first other than the web element because they are being cut totally, 100% of their length for curving process. The testing is done using a universal testing machine for a tensile load. From the experiment, specimen with full welding has shown as a good result with an ultimate load of 13.37 kN and reported having 35.41% when compared with normal specimen without any of connection methods. Furthermore, the experimental result is distinguished by using Eurocode 3. The failure of a full welding specimen is due to breaking at the welding location. Additionally, all specimens with either full weld or spot weld or combination failed due to breaking on weld connection, but specimen with flange plate and self-drilling screw failed due to tilting and bearing. Finally, the full welding specimen is chosen as a good connection to perform the strengthening method of CFCCS section.

Contact arc metal cutting (CAMC), a young cutting technique has matured. Successful use under water in the demolition of the Karlsruhe multipurpose research reactor (MFZR)

International Nuclear Information System (INIS)

Stanke, D.; Bienia, H.; Loeb, A.; Thoma, M.; Eisenmann, B.; Prechtl, E.; Suessdorf, W.; Kremer, G.; Ruemenapp, T.

2006-01-01

Dismantling radiologically burdened large components is among the most complex and difficult jobs in the demolition of nuclear installations. The technologies used and their safe operation play a key role in demolition. Dismantling highly activated components as a rule requires shielding by water. As a consequence, the techniques employed must be designed for use under water. A variety of technologies are available for these applications. One established mechanical cutting method is water abrasive suspension jet cutting (WASS). Because of the small cutting nozzle employed, this highly flexible cutting technique can be used nearly anywhere together with different guiding systems. In the course of disassembly under water of the MZFR, plasma cutting has been found to be a reliable and efficient technique for remote operation. Contact arc metal cutting is a thermal cutting technique allowing all electrically conducting materials, including those with claddings, to be cut nearly irrespective of their component geometries. The methods, technology, possible uses, and practical operation of contact arc metal cutting in the demolition of the MZFR are covered in this article. (orig.)

Innovations: laser-cutting nickel-titanium

Energy Technology Data Exchange (ETDEWEB)

Dickson, T.R.; Moore, B.; Toyama, N. [LPL Systems, Inc., Mountain View, CA (United States)

2002-07-01

Laser-cutting is well established as the preferred method for manufacturing many endovascular medical devices. Sometimes laser processing has been poorly understood by nickel-titanium (NiTi) material suppliers, medical device manufacturers, and device designers, but the field has made important strides in the past several years. A variety of sample, nonspecific applications are presented for cutting tubing and sheet stock. Limiting constraints, key considerations, and areas for future development are identified. (orig.)

Improvement of a separation method for the reduction of secondary waste from the water-jet abrasive suspension cutting technique

International Nuclear Information System (INIS)

Brandauer, M.; Gentes, S.; Heneka, A.; Krauss, C.O.; Geckeis, H.; Plaschke, M.; Schild, D.; Tobie, W.

2017-01-01

Full text of publication follows. Disassembling the reactor pressure vessel and its built-in components is a huge challenge in the deconstruction of a nuclear power plant. After being exposed to neutron irradiation for years, the activated components need to be disassembled and packed by remote controlled techniques. Underwater disassembling systems have the advantage of the shielding effect of water against radiation. To avoid the generation of aerosols, cold cutting processes are preferred. A cutting method that meets these requirements is the water-jet abrasive suspension cutting technique (WASS). This method provides high flexibility and is immune towards mechanical stress in the components. During the cutting process, a mixture of abrasive particles and radioactive steel particles from the cut components is generated. Depending on the operational conditions, the amount of this secondary waste increases substantially. Therefore, despite of its intrinsic technical benefits, WASS has a serious disadvantage towards other cutting techniques due to the huge disposal costs of secondary waste. During our previous joint research project between KIT and AREVA GmbH called NENAWAS ('New Disposal Methods for the Secondary Waste Treatment of the Water-jet Abrasive Suspension Cutting Technique', funded by the German ministry for education and research, BMBF), a prototype separation device for WASS secondary waste was developed and tested. Using a magnetic filter, steel particles could be successfully separated from the rest of the secondary waste. The separation process is examined using elemental analysis (ICP-OES) for quantification of the separation grade. Additionally, morphologies of particles and particle aggregates before and after the separation process were examined by scanning electron microscopy (SEM). In the abrasive particle fraction after separation of the steel particles a remaining contamination by tiny steel particles could be detected by elemental and

Assessment of the applicability of AWJ technique for dismantling the reactor of Fugen. Performance of underwater-cutting thick plate and testing of sound-based monitoring for underwater-cutting process

International Nuclear Information System (INIS)

Maruyama, Shin-ichiro; Nishio, Shin-ichi

2010-01-01

The reactor of Fugen is characterized by its double-walled pressure tube construction that is composed of pressure tubes and calandria tubes. The reactor dismantlement has been planning on dismantling it under water and the abrasive water jet (AWJ) underwater-cutting method is chosen as an option among simultaneous double tubes cutting technologies. For assessing the applicability of the AWJ cutting technology, a thick plate was cut under water by the small AWJ cutting machine. In addition, since cutting causes muddiness in water, cutting was monitored by the sound-based monitoring system which was adopted as a secondary cutting monitoring method. As a results, it was demonstrated that one-phase cutting was possible under water for a stainless-steel plate with 150mm thickness and that the relationship between cutting depth and capable cutting speed could be predictable. As for the sound-based cutting monitoring, the predictability whether or not cutting would be successful was verified by checking the change of sounds level. (author)

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mengjiao Yu; Ramadan Ahmed; Mark Pickell; Len Volk; Lei Zhou; Zhu Chen; Aimee Washington; Crystal Redden

2003-09-30

The Quarter began with installing the new drill pipe, hooking up the new hydraulic power unit, completing the pipe rotation system (Task 4 has been completed), and making the SWACO choke operational. Detailed design and procurement work is proceeding on a system to elevate the drill-string section. The prototype Foam Generator Cell has been completed by Temco and delivered. Work is currently underway to calibrate the system. Literature review and preliminary model development for cuttings transportation with polymer foam under EPET conditions are in progress. Preparations for preliminary cuttings transport experiments with polymer foam have been completed. Two nuclear densitometers were re-calibrated. Drill pipe rotation system was tested up to 250 RPM. Water flow tests were conducted while rotating the drill pipe up to 100 RPM. The accuracy of weight measurements for cuttings in the annulus was evaluated. Additional modifications of the cuttings collection system are being considered in order to obtain the desired accurate measurement of cuttings weight in the annular test section. Cutting transport experiments with aerated fluids are being conducted at EPET, and analyses of the collected data are in progress. The printed circuit board is functioning with acceptable noise level to measure cuttings concentration at static condition using ultrasonic method. We were able to conduct several tests using a standard low pass filter to eliminate high frequency noise. We tested to verify that we can distinguish between different depths of sand in a static bed of sand. We tested with water, air and a mix of the two mediums. Major modifications to the DTF have almost been completed. A stop-flow cell is being designed for the DTF, the ACTF and Foam Generator/Viscometer which will allow us to capture bubble images without the need for ultra fast shutter speeds or microsecond flash system.

Psychophysiological types of clinically healthy individuals with different levels of teeth resistance to caries

Directory of Open Access Journals (Sweden)

V.G. Khalturina

2010-06-01

Full Text Available The work is a result of the psychophysiological tests with the help of cutting examination and psychogeometrical tests for 76 healthy individuals ages 20,18±1,25 years, having different caries resistance. It is known that group of people with poor caries resistance has a conflict type of personality. There is a positive tendency to growth of anxiety level and reducing caries resistance. The article concludes that the prophylaxis of caries and its complications must contain methods of psychophysiological correction

Wedge cutting of mild steel by CO 2 laser and cut-quality assessment in relation to normal cutting

Science.gov (United States)

Yilbas, B. S.; Karatas, C.; Uslan, I.; Keles, O.; Usta, Y.; Yilbas, Z.; Ahsan, M.

2008-10-01

In some applications, laser cutting of wedge surfaces cannot be avoided in sheet metal processing and the quality of the end product defines the applicability of the laser-cutting process in such situations. In the present study, CO 2 laser cutting of the wedge surfaces as well as normal surfaces (normal to laser beam axis) is considered and the end product quality is assessed using the international standards for thermal cutting. The cut surfaces are examined by the optical microscopy and geometric features of the cut edges such as out of flatness and dross height are measured from the micrographs. A neural network is introduced to classify the striation patterns of the cut surfaces. It is found that the dross height and out of flatness are influenced significantly by the laser output power, particularly for wedge-cutting situation. Moreover, the cut quality improves at certain value of the laser power intensity.

In Vitro Evaluation of the Effect of Tooth Structure Loss on Fracture Resistance of Endodontically Treated Teeth

Directory of Open Access Journals (Sweden)

Shirinzad M

2017-06-01

Full Text Available Introduction: Since preserving the structure of treated teeth is a critical success factor, studying the effects of tooth structure loss on fracture resistance of the tooth tissue appears necessary. The aim of this study was to evaluate the consequences of the loss of different tissues regarding fracture resistance of teeth undergoing root canal treatment without the use of indirect restorations. Methods :In this experimental study, 70 healthy maxillary first premolar teeth were randomly divided into 7 groups of 10 members, including control group, endodontic access preparation only, MOD cavity preparation, cutting buccal cusp, cutting palatal cusp, cutting buccal cusp and marginal ridge, and cutting the palatal cusp and marginal ridge. The coronal section of teeth was restored incrementally with light cure composite. Finally, samples underwent compressive load with 45˚ angle from each cusp slope in the middle of cusp with an instant speed of 1 mm per min in the Instron machine. Fracture resistance was measured and samples were examined under stereo-microscope to evaluate the mode of failure. Results: The resistance to fracture in root canal treated teeth in different groups in order from first to seventh was 797.13 ± 52.92, 722.50 ± 131.40, 432.15 ± 203.20, 592.66 ± 195.86 124.53 ± 33.09, 85.17 ± 18.45, and 26.03 ± 5.21 Newton. ANOVA test showed statistically significant differences between the groups in terms of their fracture resistance (P = 0.000. Conclusions: The results showed that fracture resistance levels of teeth were significantly affected by amount of their tissue loss. In this study, removal of teeth palatal cusp and marginal ridge had a significant effect on decreasing the fracture resistance, while removing the buccal cusps alone cannot have a significant effect.

CAD for cutting head exchange of roadheader

Energy Technology Data Exchange (ETDEWEB)

Tao, Z.; Wu, Z.; Qian, P. [China Coal Research Institute (China). Shanghai Branch

1999-08-01

Improving the cutting method according to the actual operating conditions is an effective way to raise production efficiency. A cutting head designed by means of computer and CAD software is characterized by short design cycle but high design quality. Taking the AM-50 road header as an example, this paper shows that it is feasible to design an interchangeable cutting head for the machine without interfering with the main technical parameters. 2 refs., 5 figs., 1 tab.

PHYSICAL-MATEMATICALSCIENCE MECHANICS SIMULATION CHALLENGES IN OPTIMISING THEORETICAL METAL CUTTING TASKS

Directory of Open Access Journals (Sweden)

Rasul V. Guseynov

2017-01-01

Full Text Available Abstract. Objectives In the article, problems in the optimising of machining operations, which provide end-unit production of the required quality with a minimum processing cost, are addressed. Methods Increasing the effectiveness of experimental research was achieved through the use of mathematical methods for planning experiments for optimising metal cutting tasks. The minimal processing cost model, in which the objective function is polynomial, is adopted as a criterion for the selection of optimal parameters. Results Polynomial models of the influence of angles φ, α, γ on the torque applied when cutting threads in various steels are constructed. Optimum values of the geometrical tool parameters were obtained using the criterion of minimum cutting forces during processing. The high stability of tools having optimal geometric parameters is determined. It is shown that the use of experimental planning methods allows the optimisation of cutting parameters. In optimising solutions to metal cutting problems, it is found to be expedient to use multifactor experimental planning methods and to select the cutting force as the optimisation parameter when determining tool geometry. Conclusion The joint use of geometric programming and experiment planning methods in order to optimise the parameters of cutting significantly increases the efficiency of technological metal processing approaches. 

Searching for Dual AGNs in Galaxy Mergers: Understanding Double-Peaked [O III] and Ultra Hard X-rays as Selection Method

Science.gov (United States)

McGurk, Rosalie C.; Max, Claire E.; Medling, Anne; Shields, Gregory A.

2015-01-01

galaxy or a companion galaxy hosting a second AGN, in order to understand the role molecular gas plays in feeding this unusual population of ultra-hard X-ray AGNs and to understand ultra-hard X-rays as a dual AGN selection method.

International feedback experience on the cutting of reactor internal components

International Nuclear Information System (INIS)

Boucau, J.

2014-01-01

Westinghouse capitalizes more than 30 years of experience in the cutting of internal components of reactor and their packaging in view of their storage. Westinghouse has developed and validated different methods for cutting: plasma torch cutting, high pressure abrasive water jet cutting, electric discharge cutting and mechanical cutting. A long feedback experience has enabled Westinghouse to list the pros and cons of each cutting technology. The plasma torch cutting is fast but rises dosimetry concerns linked to the control of the cuttings and the clarity of water. Abrasive water jet cutting requires the installation of costly safety devices and of an equipment for filtering water but this technology allows accurate cuttings in hard-to-reach zones. Mechanical cutting is the most favourable technology in terms of wastes generation and of the clarity of water but the cutting speed is low. (A.C.)

Mechanisms and FEM Simulation of Chip Formation in Orthogonal Cutting In-Situ TiB2/7050Al MMC

Science.gov (United States)

Wang, Wenhu; Jiang, Ruisong; Lin, Kunyang; Shao, Mingwei

2018-01-01

The in-situ TiB2/7050Al composite is a new kind of Al-based metal matrix composite (MMC) with super properties, such as low density, improved strength, and wear resistance. This paper, for a deep insight into its cutting performance, involves a study of the chip formation process and finite element simulation during orthogonal cutting in-situ TiB2/7050Al MMC. With chips, material properties, cutting forces, and tool geometry parameters, the Johnson–Cook (J–C) constitutive equation of in-situ TiB2/7050Al composite was established. Then, the cutting simulation model was established by applying the Abaqus–Explicit method, and the serrated chip, shear plane, strain rate, and temperature were analyzed. The experimental and simulation results showed that the obtained material’s constitutive equation was of high reliability, and the saw-tooth chips occurred commonly under either low or high cutting speed and small or large feed rate. From result analysis, it was found that the mechanisms of chip formation included plastic deformation, adiabatic shear, shearing slip, and crack extension. In addition, it was found that the existence of small, hard particles reduced the ductility of the MMC and resulted in segmental chips. PMID:29662047

Determination of slope failure using 2-D resistivity method

Science.gov (United States)

Muztaza, Nordiana Mohd; Saad, Rosli; Ismail, Nur Azwin; Bery, Andy Anderson

2017-07-01

Landslides and slope failure may give negative economic effects including the cost to repair structures, loss of property value and medical costs in the event of injury. To avoid landslide, slope failure and disturbance of the ecosystem, good and detailed planning must be done when developing hilly area. Slope failure classification and various factors contributing to the instability using 2-D resistivity survey conducted in Selangor, Malaysia are described. The study on landslide and slope failure was conducted at Site A and Site B, Selangor using 2-D resistivity method. The implications of the anticipated ground conditions as well as the field observation of the actual conditions are discussed. Nine 2-D resistivity survey lines were conducted in Site A and six 2-D resistivity survey lines with 5 m minimum electrode spacing using Pole-dipole array were performed in Site B. The data were processed using Res2Dinv and Surfer10 software to evaluate the subsurface characteristics. 2-D resistivity results from both locations show that the study areas consist of two main zones. The first zone is alluvium or highly weathered with the resistivity of 100-1000 Ωm at 20-70 m depth. This zone consists of saturated area (1-100 Ωm) and boulders with resistivity value of 1200-3000 Ωm. The second zone with resistivity values of > 3000 Ωm was interpreted as granitic bedrock. The study area was characterized by saturated zones, highly weathered zone, highly contain of sand and boulders that will trigger slope failure in the survey area. Based on the results obtained from the study findings, it can be concluded that 2-D resistivity method is useful method in determination of slope failure.

Baking Performance of Phosphorylated Cross-Linked Resistant Starch in Low-Moisture Bakery Goods

Science.gov (United States)

Phosphorylated cross-linked resistant starch (RS) is a type 4 RS, which can be used for enhancing the benefits of dietary fiber. The baking performance of the RS was explored using wire-cut cookie baking and benchtop chemically-leavened cracker baking methods to produce low-moisture baked goods (coo...

Evaluation of Combined Disinfection Methods for Reducing Escherichia coli O157:H7 Population on Fresh-Cut Vegetables

Directory of Open Access Journals (Sweden)

Eva Petri

2015-07-01

Full Text Available Most current disinfection strategies for fresh-cut industry are focused on the use of different chemical agents; however, very little has been reported on the effectiveness of the hurdle technology. The effect of combined decontamination methods based on the use of different sanitizers (peroxyacetic acid and chlorine dioxide and the application of pressure (vacuum/positive pressure on the inactivation of the foodborne pathogen E. coli O157:H7 on fresh-cut lettuce (Lactuca sativa and carrots (Daucus carota was studied. Fresh produce, inoculated with E. coli O157:H7, was immersed (4 °C, 2 min in tap water (W, chlorine water (CW, chlorine dioxide (ClO2: 2 mg/L and peroxyacetic acid (PAA: 100 mg/L in combination with: (a vacuum (V: 10 mbar or (b positive pressure application (P: 3 bar. The product quality and antimicrobial effects of the treatment on bacterial counts were determined both in process washing water and on fresh-cut produce. Evidence obtained in this study, suggests that the use of combined methods (P/V + sanitizers results in a reduction on the microorganism population on produce similar to that found at atmospheric pressure. Moreover, the application of physical methods led to a significant detrimental effect on the visual quality of lettuce regardless of the solution used. Concerning the process water, PAA proved to be an effective alternative to chlorine for the avoidance of cross-contamination.

Evaluation of Combined Disinfection Methods for Reducing Escherichia coli O157:H7 Population on Fresh-Cut Vegetables.

Science.gov (United States)

Petri, Eva; Rodríguez, Mariola; García, Silvia

2015-07-23

Most current disinfection strategies for fresh-cut industry are focused on the use of different chemical agents; however, very little has been reported on the effectiveness of the hurdle technology. The effect of combined decontamination methods based on the use of different sanitizers (peroxyacetic acid and chlorine dioxide) and the application of pressure (vacuum/positive pressure) on the inactivation of the foodborne pathogen E. coli O157:H7 on fresh-cut lettuce (Lactuca sativa) and carrots (Daucus carota) was studied. Fresh produce, inoculated with E. coli O157:H7, was immersed (4 °C, 2 min) in tap water (W), chlorine water (CW), chlorine dioxide (ClO2: 2 mg/L) and peroxyacetic acid (PAA: 100 mg/L) in combination with: (a) vacuum (V: 10 mbar) or (b) positive pressure application (P: 3 bar). The product quality and antimicrobial effects of the treatment on bacterial counts were determined both in process washing water and on fresh-cut produce. Evidence obtained in this study, suggests that the use of combined methods (P/V + sanitizers) results in a reduction on the microorganism population on produce similar to that found at atmospheric pressure. Moreover, the application of physical methods led to a significant detrimental effect on the visual quality of lettuce regardless of the solution used. Concerning the process water, PAA proved to be an effective alternative to chlorine for the avoidance of cross-contamination.

Study on Roadheader Cutting Load at Different Properties of Coal and Rock

Directory of Open Access Journals (Sweden)

Xueyi Li

2013-01-01

Full Text Available The mechanism of cutting process of roadheader with cutting head was researched, and the influences of properties of coal and rock on cutting load were deeply analyzed. Aimed at the defects of traditional calculation method of cutting load on fully expressing the complex cutting process of cutting head, the method of finite element simulation was proposed to simulate the dynamic cutting process. Aimed at the characteristics of coal and rock which affect the cutting load, several simulations with different firmness coefficient were taken repeatedly, and the relationship between three-axis force and firmness coefficient was derived. A comparative analysis of cutting pick load between simulation results and theoretical formula was carried out, and a consistency was achieved. Then cutting process with a total cutting head was carried out on this basis. The results show that the simulation analysis not only provides a reliable guarantee for the accurate calculation of the cutting head load and improves the efficiency of the cutting head cutting test but also offers a basis for selection of cutting head with different geological conditions of coal or rock.

A new capacitive/resistive probe method for studying magnetic surfaces

International Nuclear Information System (INIS)

Kitajima, Sumio; Takayama, Masakazu; Zama, Tatsuya; Takaya, Kazuhiro; Takeuchi, Nobunao; Watanabe, Hiroshige

1991-01-01

A new capacitive/resistive probe method for mapping the magnetic surfaces from resistance or capacitance between a magnetic surface and a vacuum vessel was developed and tested. Those resistances and capacitances can be regarded as components of a simple electrical bridge circuit. This method exploits electrical transient response of the bridge circuit for a square pulse. From equiresistance or equicapacitance points, the magnetic surface structure can be deduced. Measurements on the Tohoku University Heliac, which is a small-size standard heliac, show good agreement with numerical calculations. This method is particularly useful for pulse-operated machines. (author)

A Cutting Pattern Recognition Method for Shearers Based on Improved Ensemble Empirical Mode Decomposition and a Probabilistic Neural Network

Directory of Open Access Journals (Sweden)

Jing Xu

2015-10-01

Full Text Available In order to guarantee the stable operation of shearers and promote construction of an automatic coal mining working face, an online cutting pattern recognition method with high accuracy and speed based on Improved Ensemble Empirical Mode Decomposition (IEEMD and Probabilistic Neural Network (PNN is proposed. An industrial microphone is installed on the shearer and the cutting sound is collected as the recognition criterion to overcome the disadvantages of giant size, contact measurement and low identification rate of traditional detectors. To avoid end-point effects and get rid of undesirable intrinsic mode function (IMF components in the initial signal, IEEMD is conducted on the sound. The end-point continuation based on the practical storage data is performed first to overcome the end-point effect. Next the average correlation coefficient, which is calculated by the correlation of the first IMF with others, is introduced to select essential IMFs. Then the energy and standard deviation of the reminder IMFs are extracted as features and PNN is applied to classify the cutting patterns. Finally, a simulation example, with an accuracy of 92.67%, and an industrial application prove the efficiency and correctness of the proposed method.

Optimizing cutting conditions on sustainable machining of aluminum alloy to minimize power consumption

Science.gov (United States)

Nur, Rusdi; Suyuti, Muhammad Arsyad; Susanto, Tri Agus

2017-06-01

Aluminum is widely utilized in the industrial sector. There are several advantages of aluminum, i.e. good flexibility and formability, high corrosion resistance and electrical conductivity, and high heat. Despite of these characteristics, however, pure aluminum is rarely used because of its lacks of strength. Thus, most of the aluminum used in the industrial sectors was in the form of alloy form. Sustainable machining can be considered to link with the transformation of input materials and energy/power demand into finished goods. Machining processes are responsible for environmental effects accepting to their power consumption. The cutting conditions have been optimized to minimize the cutting power, which is the power consumed for cutting. This paper presents an experimental study of sustainable machining of Al-11%Si base alloy that was operated without any cooling system to assess the capacity in reducing power consumption. The cutting force was measured and the cutting power was calculated. Both of cutting force and cutting power were analyzed and modeled by using the central composite design (CCD). The result of this study indicated that the cutting speed has an effect on machining performance and that optimum cutting conditions have to be determined, while sustainable machining can be followed in terms of minimizing power consumption and cutting force. The model developed from this study can be used for evaluation process and optimization to determine optimal cutting conditions for the performance of the whole process.

Slice-push, formation of grooves and the scale effect in cutting.

Science.gov (United States)

Atkins, A G

2016-06-06

Three separate aspects of cutting are investigated which complement other papers on the mechanics of separation processes presented at this interdisciplinary Theo Murphy meeting. They apply in all types of cutting whether blades are sharp or blunt, and whether the material being cut is 'hard, stiff and strong' or 'soft, compliant and weak'. The first topic discusses why it is easier to cut when there is motion along (parallel to) the blade as well motion across (perpendicular to) the cutting edge, and the analysis is applied to optimization of blade geometries to produce minimum cutting forces and hence minimum damage to cut surfaces. The second topic concerns cutting with more than one edge with particular application to the formation of grooves in surfaces by hard pointed tools. The mechanics are investigated and applied to the topic of abrasive wear by hard particles. Traditional analyses say that abrasive wear resistance increases monotonically with the hardness of the workpiece, but we show that the fracture toughness of the surface material is also important, and that behaviour is determined by the toughness-to-hardness ratio rather than hardness alone. Scaling forms the third subject. As cutting is a branch of elasto-plastic fracture mechanics, cube-square energy scaling applies in which the important length scale is (ER/k (2)), where E is Young's modulus, R is the fracture toughness and k is the shear yield strength. Whether, in cutting, material is removed as ductile ribbons, as semi-ductile discontinuous chips, or by brittle 'knocking lumps out' is shown to depend on the depth of cut relative to this characteristic length parameter. Scaling in biology is called allometry and its relationship with engineering scaling is discussed. Some speculative predictions are made in relation to the action of teeth on food.

Precision Machining When Cutting with Leading Plastic Deformation

Directory of Open Access Journals (Sweden)

N. A. Yaroslavtseva

2017-01-01

Full Text Available Keeping up the product competitiveness continually requires solving the problems of reducing time for product creation and material costs for its production and ensuring the maximum conformity of the product quality with the individual requirements of a particular consumer. It is especially difficult to implement these tasks in product manufacturing from the hard-to-machine steels and alloys with extremely low production rate in machining (often 10-20 times lower than when cutting the ordinary structural steels.Currently, one of the promising ways to improve the cutting process of hard-to-machine materials and quality of parts made from these materials is development and application of combined processing methods, which use additional energy sources to act on the machined material in the cutting zone. A BMSTU-developed cutting method with leading plastic deformation (LPD, which acts to raise the production rate, gain the cutting tool-life, reduce the surface roughness, improve the accuracy of processing and the performance characteristics of products, ensure the reliable flow chip control, and improve the labor conditions, belongs to such sort of methods.One of the most important indicators of processing quality that has a great impact on the operation and cost characteristics of the product and on the machining rate as well is the accuracy of processing. In cutting, the processing errors largely arise from the elastic deformations of a technological system when the cutting force, and, in particular, the radial component of the cutting force, acts on it.The deforming devices, used in cutting with LPD, being located as a rule, on the diametrically opposite side with respect to the cutting zone, act on the technological system as vibration dampers. In addition, as studies have shown, the choice of a rational direction for applying LPD load helps to compensate partially or completely the cutting force radial component effect on the technological

Status on underwater plasma arc cutting in KHI, 3

International Nuclear Information System (INIS)

Abe, Tadashi; Aota, Toshiichi; Nishizaki, Tadashi; Nakayama, Shigeru; Yamashita, Seiji

1983-01-01

In Kawasaki Heavy Industries, Ltd., the development of a remote dismantling system by underwater plasma arc cutting process has been advanced, expecting its application to the dismantling and removal of nuclear reactor facilities. In the previous two reports, the fundamental experimental results such as the comparison of the cutting capability in air and in water were shown, but this time, the remote automatic cutting of wedge-shaped specimens was carried out, using a newly installed manipulator for underwater works, therefore its outline is reported. Also the cutting experiment by overhead position and vertical position was performed by using the same equipment, and comparison was made with the cutting capability by downhand and horizontal positions. It is important to grasp the cutting characteristics in the case of upward advancing and downward advancing cuttings by overhead and vertical positions when the cutting of pressure vessels and horizontal pipes into rings is supposed. The experimental apparatus, the cutting conditions, the testing method and the test results of the cutting capability test, the test of changing direction during cutting, and the remote cutting of pipes into rings are described. The underwater plasma arc cutting can cut all metals, the cutting speed is relatively high, and the apparatus is simple and compact. (Kako, I.)

High speed cutting of AZ31 magnesium alloy

Directory of Open Access Journals (Sweden)

Liwei Lu

2016-06-01

Full Text Available Using LBR-370 numerical control lathe, high speed cutting was applied to AZ31 magnesium alloy. The influence of cutting parameters on microstructure, surface roughness and machining hardening were investigated by using the methods of single factor and orthogonal experiment. The results show that the cutting parameters have an important effect on microstructure, surface roughness and machine hardening. The depth of stress layer, roughness and hardening present a declining tendency with the increase of the cutting speed and also increase with the augment of the cutting depth and feed rate. Moreover, we established a prediction model of the roughness, which has an important guidance on actual machining process of magnesium alloy.

Development of cutting machine for disposal of highly activated equipments

International Nuclear Information System (INIS)

Iimura, Katumichi; Kitajima, Toshio; Hosokawa, Jinsaku; Abe, Shinichi; Takahashi, Kiyoshi; Ogawa, Mituhiro; Iwai, Takashi

1994-01-01

JMTR (Japan Materials Testing Reactor) Project has developed a cutting machine which can cut a highly activated in-pile tube under water and its performance and safety have been confirmed. This machine is for the purpose of cutting a multiplet structure pipe and made possible to cut it under water by adopting under-water discharge method. Furthermore, contamination of canal water and atmosphere is prevented by combining a filter with this machine. This report describes the outline and performance of the developed cutting machine and also results of cutting highly activated in-pile tubes. (author)

High power laser downhole cutting tools and systems

Science.gov (United States)

Zediker, Mark S; Rinzler, Charles C; Faircloth, Brian O; Koblick, Yeshaya; Moxley, Joel F

2015-01-20

Downhole cutting systems, devices and methods for utilizing 10 kW or more laser energy transmitted deep into the earth with the suppression of associated nonlinear phenomena. Systems and devices for the laser cutting operations within a borehole in the earth. These systems and devices can deliver high power laser energy down a deep borehole, while maintaining the high power to perform cutting operations in such boreholes deep within the earth.

Water-Cut Sensor System

KAUST Repository

Karimi, Muhammad Akram

2018-01-11

Provided in some embodiments is a method of manufacturing a pipe conformable water-cut sensors system. Provided in some embodiments is method for manufacturing a water-cut sensor system that includes providing a helical T-resonator, a helical ground conductor, and a separator at an exterior of a cylindrical pipe. The helical T-resonator including a feed line, and a helical open shunt stub conductively coupled to the feed line. The helical ground conductor including a helical ground plane opposite the helical open shunt stub and a ground ring conductively coupled to the helical ground plane. The feed line overlapping at least a portion of the ground ring, and the separator disposed between the feed line and the portion of the ground ring overlapped by the feed line to electrically isolate the helical T-resonator from the helical ground conductor.

Si3N4 ceramic cutting tool sintered with CeO2 and Al2O3 additives with AlCrN coating

Directory of Open Access Journals (Sweden)

José Vitor Candido Souza

2011-12-01

Full Text Available Ceramic cutting tools are showing a growing market perspective in terms of application on machining operations due to their high hardness, wear resistance, and machining without a cutting fluid, therefore are good candidates for cast iron and Nickel superalloys machining. The objective of the present paper was the development of Si3N4 based ceramic cutting insert, characterization of its physical and mechanical properties, and subsequent coating with AlCrN using a PVD method. The characterization of the coating was made using an optical profiler, XRD, AFM and microhardness tester. The results showed that the tool presented a fracture toughness of 6.43 MPa.m½ and hardness of 16 GPa. The hardness reached 31 GPa after coating. The machining tests showed a decrease on workpiece roughness when machining with coated insert, in comparison with the uncoated cutting tool. Probably this fact is related to hardness, roughness and topography of AlCrN.

[Optimization of cluster analysis based on drug resistance profiles of MRSA isolates].

Science.gov (United States)

Tani, Hiroya; Kishi, Takahiko; Gotoh, Minehiro; Yamagishi, Yuka; Mikamo, Hiroshige

2015-12-01

We examined 402 methicillin-resistant Staphylococcus aureus (MRSA) strains isolated from clinical specimens in our hospital between November 19, 2010 and December 27, 2011 to evaluate the similarity between cluster analysis of drug susceptibility tests and pulsed-field gel electrophoresis (PFGE). The results showed that the 402 strains tested were classified into 27 PFGE patterns (151 subtypes of patterns). Cluster analyses of drug susceptibility tests with the cut-off distance yielding a similar classification capability showed favorable results--when the MIC method was used, and minimum inhibitory concentration (MIC) values were used directly in the method, the level of agreement with PFGE was 74.2% when 15 drugs were tested. The Unweighted Pair Group Method with Arithmetic mean (UPGMA) method was effective when the cut-off distance was 16. Using the SIR method in which susceptible (S), intermediate (I), and resistant (R) were coded as 0, 2, and 3, respectively, according to the Clinical and Laboratory Standards Institute (CLSI) criteria, the level of agreement with PFGE was 75.9% when the number of drugs tested was 17, the method used for clustering was the UPGMA, and the cut-off distance was 3.6. In addition, to assess the reproducibility of the results, 10 strains were randomly sampled from the overall test and subjected to cluster analysis. This was repeated 100 times under the same conditions. The results indicated good reproducibility of the results, with the level of agreement with PFGE showing a mean of 82.0%, standard deviation of 12.1%, and mode of 90.0% for the MIC method and a mean of 80.0%, standard deviation of 13.4%, and mode of 90.0% for the SIR method. In summary, cluster analysis for drug susceptibility tests is useful for the epidemiological analysis of MRSA.

Antimicrobial resistance and resistance genes in Salmonella strains isolated from broiler chickens along the slaughtering process in China.

Science.gov (United States)

Zhu, Yuanting; Lai, Haimei; Zou, Likou; Yin, Sheng; Wang, Chengtao; Han, Xinfeng; Xia, Xiaolong; Hu, Kaidi; He, Li; Zhou, Kang; Chen, Shujuan; Ao, Xiaolin; Liu, Shuliang

2017-10-16

A total of 189 Salmonella isolates were recovered from 627 samples which were collected from cecal contents of broilers, chicken carcasses, chicken meat after cutting step and frozen broiler chicken products along the slaughtering process at a slaughterhouse in Sichuan province of China. The Salmonella isolates were subjected to antimicrobial susceptibility testing to 10 categories of antimicrobial agents using the Kirby-Bauer disk diffusion method. Those antibiotics-resistant isolates were further investigated for the occurrence of resistance genes, the presence of class 1 integron as well as the associated gene cassettes, and the mutations within the gyrA and parC genes. Consequently, the prevalence of Salmonella was 30.14% (47.96% for cecal content, 18.78% for chicken carcasses, 31.33% for cutting meat and 14.00% for frozen meat, respectively). The predominant serotypes were S. Typhimurium (15.34%) and S. Enteritidis (69.84%). High resistance rates to the following drugs were observed: nalidixic acid (99.5%), ampicillin (87.8%), tetracycline (51.9%), ciprofloxacin (48.7%), trimethoprim/sulfamethoxazole (48.1%), and spectinomycin (34.4%). Antimicrobial resistance profiling showed that 60.8% of isolates were multidrug resistant (MDR), and MDR strains increased from 44.7% to 78.6% along the slaughtering line. 94.6% (n=157) of beta-lactam-resistant isolates harbored at least one resistance gene of bla TEM or bla CTX-M . The relatively low prevalence of aminoglycoside resistance genes (aac(3)-II, aac(3)-IV, and ant(2″)-I) was found in 49 (66.2%) of antibiotic-resistant isolates. The tetracycline resistance genes (tet(A), tet(B), tet(C), and tet(G) and sulfonamide resistance genes (sul1, sul2, and sul3) were identified in 84 (85.7%) and 89 (97.8%) antibiotic-resistant isolates respectively. floR was identified in 44 (97.8%) florfenicol-resistant isolates. Class 1 integron was detected in 37.4% (n=43) of the MDR isolates. Two different gene cassettes, bla OXA-30 -aad

Graph cut-based method for segmenting the left ventricle from MRI or echocardiographic images.

Science.gov (United States)

Bernier, Michael; Jodoin, Pierre-Marc; Humbert, Olivier; Lalande, Alain

2017-06-01

In this paper, we present a fast and interactive graph cut method for 3D segmentation of the endocardial wall of the left ventricle (LV) adapted to work on two of the most widely used modalities: magnetic resonance imaging (MRI) and echocardiography. Our method accounts for the fundamentally different nature of both modalities: 3D echocardiographic images have a low contrast, a poor signal-to-noise ratio and frequent signal drop, while MR images are more detailed but also cluttered and contain highly anisotropic voxels. The main characteristic of our method is to work in a 3D Bezier coordinate system instead of the original Euclidean space. This comes with several advantages, including an implicit shape prior and a result guarantied not to have any holes in it. The proposed method is made of 4 steps. First, a 3D sampling of the LV cavity is made based on a Bezier coordinate system. This allows to warp the input 3D image to a Bezier space in which a plane corresponds to an anatomically plausible 3D Euclidean bullet shape. Second, a 3D graph is built and an energy term (which is based on the image gradient and a 3D probability map) is assigned to each edge of the graph, some of which being given an infinite energy to ensure the resulting 3D structure passes through key anatomical points. Third, a max-flow min-cut procedure is executed on the energy graph to delineate the endocardial surface. And fourth, the resulting surface is projected back to the Euclidean space where a post-processing convex hull algorithm is applied on every short axis slice to remove local concavities. Results obtained on two datasets reveal that our method takes between 2 and 5s to segment a 3D volume, it has better results overall than most state-of-the-art methods on the CETUS echocardiographic dataset and is statistically as good as a human operator on MR images. Copyright © 2017 Elsevier Ltd. All rights reserved.

Impact of Cutting Forces and Chip Microstructure in High Speed Machining of Carbon Fiber – Epoxy Composite Tube

Directory of Open Access Journals (Sweden)

Roy Y. Allwin

2017-09-01

Full Text Available Carbon fiber reinforced polymeric (CFRP composite materials are widely used in aerospace, automobile and biomedical industries due to their high strength to weight ratio, corrosion resistance and durability. High speed machining (HSM of CFRP material is needed to study the impact of cutting parameters on cutting forces and chip microstructure which offer vital inputs to the machinability and deformation characteristics of the material. In this work, the orthogonal machining of CFRP was conducted by varying the cutting parameters such as cutting speed and feed rate at high cutting speed/feed rate ranges up to 346 m/min/ 0.446 mm/rev. The impact of the cutting parameters on cutting forces (principal cutting, feed and thrust forces and chip microstructure were analyzed. A significant impact on thrust forces and chip segmentation pattern was seen at higher feed rates and low cutting speeds.

Evaluation of The Effects of Cutting Parameters On The Surface Roughness During The Turning of Hadfield Steel With Response Surface Methodology

Directory of Open Access Journals (Sweden)

Ergün EKİCİ

2014-12-01

Full Text Available Hadfield steel (X120Mn12 is widely used in the engineering applications due to its excellent wear resistance. In this study, the effects of the cutting parameters on the surface roughness were investigated in relation to the lathe process carried out on Hadfield steel. The experiments were conducted at a cutting speed of 80, 110, 140 m/min, feed rate of 0.2, 0.3, 0.4 mm/rev and depth of cut 0.2, 0.4, 0.6 mm, using coated carbide tools. Regarding the evaluation of the machinability of Hadfield steel, a model was formed utilizing the response surface method (RSM. For the determination of the effects of the cutting parameters on the surface roughness, the central composite design (CCD and variance analysis (ANOVA were used. By means of the model formed as a result of the experimental study, it was demonstrated that among the cutting parameters, the feed rate is the most effective parameter on the surface roughness, with a contribution ratio of 90.28%. It was determined that the surface roughness increases with increasing feed rate. With respect to the effect on the surface roughness, the feed rate was followed by the cutting speed with a contribution ratio of 3.1% and the cutting depth with a contribution ratio of 1.7%.

The analysis of mechanism of rhenium-coated tools' wear-resistance rising

Directory of Open Access Journals (Sweden)

Daniel Petrosyan

2017-06-01

Full Text Available It is proposed to obtain wear-resistant layers on the hard-alloy materials by thermochemical treatment. In the different field of production – mechanical engineering, metallurgy and military technologies, with machine parts demanding high wearproof and corrosion-proof machinery parts on the surfaces of syntheses of diamonds, with metal surface thermal-diffusion with rhenium, to receive diffusion wearing layers for the first time. A method for thermochemical treatment of hard alloy plates has been investigated, allowing to raise the wear-resistance of cutting and mining tools.

Cutting forces during turning with variable depth of cut

Directory of Open Access Journals (Sweden)

M. Sadílek

2016-03-01

The proposed research for the paper is an experimental work – measuring cutting forces and monitoring of the tool wear on the cutting edge. It compares the turning where standard roughing cycle is used and the turning where the proposed roughing cycle with variable depth of cut is applied.

Functional anatomy of the water transport system in cut chrysanthemum

NARCIS (Netherlands)

Nijsse, J.

2001-01-01

Cut flowers show a wide variance of keepability. The market demands more and more a guaranteed quality. Therefore, methods must be developed to predict vase life of cut flowers. Chrysanthemum ( Dendranthema x grandiflorum Tzvelev) and some other cut flowers suffer from

An analytical method on the surface residual stress for the cutting tool orientation

Science.gov (United States)

Li, Yueen; Zhao, Jun; Wang, Wei

2010-03-01

The residual stress is measured by choosing 8 kinds orientations on cutting the H13 dies steel on the HSM in the experiment of this paper. The measured data shows on that the residual stress exists periodicity for the different rake angle (β) and side rake angle (θ) parameters, further study find that the cutting tool orientations have closed relationship with the residual stresses, and for the original of the machined residual stress on the surface from the cutting force and the axial force, it can be gained the simply model of tool-workpiece force, using the model it can be deduced the residual stress model, which is feasible to calculate the size of residual stress. And for almost all the measured residual stresses are compressed stress, the compressed stress size and the direction could be confirmed by the input data for the H13 on HSM. As the result, the residual stress model is the key for optimization of rake angle (β) and side rake angle (θ) in theory, using the theory the more cutting mechanism can be expressed.

Effect of cutter tip angle on cutting characteristics of acrylic worksheet subjected to punch/die shearing

Directory of Open Access Journals (Sweden)

Masami Kojima

2016-12-01

Full Text Available This paper aims to describe the effect of tool geometry on cutting characteristics of a 1.0 mm thickness acrylic worksheet subjected to a punch/die shearing. A set of side-wedge punch and side-wedge die which had the edge angle of 30°, 60° and/or 90° was prepared and used for cutting off the worksheet. A load cell and a CCD camera were installed in the cutting system to investigate the cutting load resistance and the side-view deformation of the worksheet. From experimental results, it was revealed that a cracking pattern at a sheared zone was remarkably affected by the edge angle of cutting tool. A cracking direction was almost coincident to the edge angle when considering the punch/die edge angle of 30°, while any matching of them was not observed in case of the punch/die edge angle of 60°, 90°. By using the 30° side-wedge tool, a flat-smooth sheared surface was generated. When combing the punch edge angle of 90° and the die edge angle of 60°, the cracking profile was characterized by the both edge angles for each part (die and punch. Carrying out an elasto-plastic finite element method analysis of cutter indentation with a few of symmetric and asymmetric punch/die edges, the stress distribution and deformation flow at the sheared zone were discussed with the initiation of surface cracks

Influence of microwave sterilization on the cutting capacity of carbide burs.

Science.gov (United States)

Fais, Laiza Maria Grassi; Pinelli, Lígia Antunes Pereira; Adabo, Gelson Luis; Silva, Regina Helena Barbosa Tavares da; Marcelo, Caroline Canhizares; Guaglianoni, Dalton Geraldo

2009-01-01

This study compared the cutting capacity of carbide burs sterilized with microwaves and traditional sterilization methods. Sixty burs were divided into 5 groups according to the sterilization methods: dry heat (G1), autoclave (G2), microwave irradiation (G3), glutaraldehyde (G4) or control - no sterilization (G5). The burs were used to cut glass plates in a cutting machine set for twelve 2.5-min periods and, after each period, they were sterilized (except G5) following the protocol established for each group. The cutting capacity of the burs was determined by a weight-loss method. Data were analyzed statistically by Kruskal-Wallis and Dunn's test. The means of the cutting amount performed by each group after the 12 periods were G1 = 0.2167 +/- 0.0627 g; G2 = 0.2077 +/- 0.0231 g; G3 = 0.1980 +/- 0.0326 g; G4 = 0.1203 +/- 0.0459 g; G5 = 0.2642 +/- 0.0359 g. There were statistically significant differences among the groups (p<0.05); only dry heat sterilization was similar to the control. Sterilization by dry heat was the method that least affected the cutting capacity of the carbide burs and microwave sterilization was not better than traditional sterilization methods.

Reducing contact resistance in graphene devices through contact area patterning.

Science.gov (United States)

Smith, Joshua T; Franklin, Aaron D; Farmer, Damon B; Dimitrakopoulos, Christos D

2013-04-23

Performance of graphene electronics is limited by contact resistance associated with the metal-graphene (M-G) interface, where unique transport challenges arise as carriers are injected from a 3D metal into a 2D-graphene sheet. In this work, enhanced carrier injection is experimentally achieved in graphene devices by forming cuts in the graphene within the contact regions. These cuts are oriented normal to the channel and facilitate bonding between the contact metal and carbon atoms at the graphene cut edges, reproducibly maximizing "edge-contacted" injection. Despite the reduction in M-G contact area caused by these cuts, we find that a 32% reduction in contact resistance results in Cu-contacted, two-terminal devices, while a 22% reduction is achieved for top-gated graphene transistors with Pd contacts as compared to conventionally fabricated devices. The crucial role of contact annealing to facilitate this improvement is also elucidated. This simple approach provides a reliable and reproducible means of lowering contact resistance in graphene devices to bolster performance. Importantly, this enhancement requires no additional processing steps.

Influence of microwave sterilization on the cutting capacity of carbide burs

Directory of Open Access Journals (Sweden)

Laiza Maria Grassi Fais

2009-12-01

Full Text Available OBJECTIVE: This study compared the cutting capacity of carbide burs sterilized with microwaves and traditional sterilization methods. MATERIAL AND METHODS: Sixty burs were divided into 5 groups according to the sterilization methods: dry heat (G1, autoclave (G2, microwave irradiation (G3, glutaraldehyde (G4 or control - no sterilization (G5. The burs were used to cut glass plates in a cutting machine set for twelve 2.5-min periods and, after each period, they were sterilized (except G5 following the protocol established for each group. The cutting capacity of the burs was determined by a weight-loss method. Data were analyzed statistically by Kruskal-Wallis and Dunn's test. RESULTS: The means of the cutting amount performed by each group after the 12 periods were G1 = 0.2167 ± 0.0627 g; G2 = 0.2077 ± 0.0231 g; G3 = 0.1980 ± 0.0326 g; G4 = 0.1203 ± 0.0459 g; G5 = 0.2642 ± 0.0359 g. There were statistically significant differences among the groups (p<0.05; only dry heat sterilization was similar to the control. CONCLUSION: Sterilization by dry heat was the method that least affected the cutting capacity of the carbide burs and microwave sterilization was not better than traditional sterilization methods.

CO2 laser cutting of ultra thin (75 μm) glass based rigid optical solar reflector (OSR) for spacecraft application

Science.gov (United States)

Mishra, Shubham; Sridhara, N.; Mitra, Avijit; Yougandar, B.; Dash, Sarat Kumar; Agarwal, Sanjay; Dey, Arjun

2017-03-01

Present study reports for the first time laser cutting of multilayered coatings on both side of ultra thin (i.e., 75 μm) glass substrate based rigid optical solar reflector (OSR) for spacecraft thermal control application. The optimization of cutting parameters was carried out as a function of laser power, cutting speed and number of cutting passes and their effect on cutting edge quality. Systematic and in-detail microstructural characterizations were carried out by optical and scanning electron microscopy techniques to study the laser affected zone and cutting edge quality. Sheet resistance and water contact angle experiments were also conducted locally both prior and after laser cut to investigate the changes of electrical and surface properties, if any.

[Study of cuttings identification using laser-induced breakdown spectroscopy].

Science.gov (United States)

Tian, Ye; Wang, Zhen-nan; Hou, Hua-ming; Zhai, Xiao-wei; Ci, Xing-hua; Zheng, Rong-er

2012-08-01

Cutting identification is one of the most important links in the course of cutting logging which is very significant in the process of oil drilling. In the present paper, LIBS was used for identification of four kinds of cutting samples coming from logging field, and then multivariate analysis was used in data processing. The whole spectra model and the feature model were built for cuttings identification using PLS-DA method. The accuracy of the whole spectra model was 88.3%, a little more than the feature model with an accuracy of 86.7%. While in the aspect of data size, the variables were decreased from 24,041 to 27 by feature extraction, which increased the efficiency of data processing observably. The obtained results demonstrate that LIBS combined with chemometrics method could be developed as a rapid and valid approach to cutting identification and has great potential to be used in logging field.

Photodiode-based cutting interruption sensor for near-infrared lasers.

Science.gov (United States)

Adelmann, B; Schleier, M; Neumeier, B; Hellmann, R

2016-03-01

We report on a photodiode-based sensor system to detect cutting interruptions during laser cutting with a fiber laser. An InGaAs diode records the thermal radiation from the process zone with a ring mirror and optical filter arrangement mounted between a collimation unit and a cutting head. The photodiode current is digitalized with a sample rate of 20 kHz and filtered with a Chebyshev Type I filter. From the measured signal during the piercing, a threshold value is calculated. When the diode signal exceeds this threshold during cutting, a cutting interruption is indicated. This method is applied to sensor signals from cutting mild steel, stainless steel, and aluminum, as well as different material thicknesses and also laser flame cutting, showing the possibility to detect cutting interruptions in a broad variety of applications. In a series of 83 incomplete cuts, every cutting interruption is successfully detected (alpha error of 0%), while no cutting interruption is reported in 266 complete cuts (beta error of 0%). With this remarkable high detection rate and low error rate, the possibility to work with different materials and thicknesses in combination with the easy mounting of the sensor unit also to existing cutting machines highlight the enormous potential for this sensor system in industrial applications.

Small forest cuttings mapped with Landsat digital data

Science.gov (United States)

Bryant, E.; Dodge, A. G.; Eger, M. J. E.

1979-01-01

The Cooperative Landsat Applications Research Group used computer classification of Landsat digital data to map forest cuttings (clearcuts) in northern New Hampshire. Cuttings as small as 3 hectares were identified. Several ages or conditions of clearcuts could be distinguished. Progress in two methods of duplicating classification categories from one Landsat pass to another are discussed. One method was used in making maps of areas in 1973, 1975, and 1978.

Fast femtosecond laser ablation for efficient cutting of sintered alumina substrates

Science.gov (United States)

Oosterbeek, Reece N.; Ward, Thomas; Ashforth, Simon; Bodley, Owen; Rodda, Andrew E.; Simpson, M. Cather

2016-09-01

Fast, accurate cutting of technical ceramics is a significant technological challenge because of these materials' typical high mechanical strength and thermal resistance. Femtosecond pulsed lasers offer significant promise for meeting this challenge. Femtosecond pulses can machine nearly any material with small kerf and little to no collateral damage to the surrounding material. The main drawback to femtosecond laser machining of ceramics is slow processing speed. In this work we report on the improvement of femtosecond laser cutting of sintered alumina substrates through optimisation of laser processing parameters. The femtosecond laser ablation thresholds for sintered alumina were measured using the diagonal scan method. Incubation effects were found to fit a defect accumulation model, with Fth,1=6.0 J/cm2 (±0.3) and Fth,∞=2.5 J/cm2 (±0.2). The focal length and depth, laser power, number of passes, and material translation speed were optimised for ablation speed and high quality. Optimal conditions of 500 mW power, 100 mm focal length, 2000 μm/s material translation speed, with 14 passes, produced complete cutting of the alumina substrate at an overall processing speed of 143 μm/s - more than 4 times faster than the maximum reported overall processing speed previously achieved by Wang et al. [1]. This process significantly increases processing speeds of alumina substrates, thereby reducing costs, making femtosecond laser machining a more viable option for industrial users.

The effect of cutting conditions on power inputs when machining

Science.gov (United States)

Petrushin, S. I.; Gruby, S. V.; Nosirsoda, Sh C.

2016-08-01

Any technological process involving modification of material properties or product form necessitates consumption of a certain power amount. When developing new technologies one should take into account the benefits of their implementation vs. arising power inputs. It is revealed that procedures of edge cutting machining are the most energy-efficient amongst the present day forming procedures such as physical and technical methods including electrochemical, electroerosion, ultrasound, and laser processing, rapid prototyping technologies etc, such as physical and technical methods including electrochemical, electroerosion, ultrasound, and laser processing, rapid prototyping technologies etc. An expanded formula for calculation of power inputs is deduced, which takes into consideration the mode of cutting together with the tip radius, the form of the replaceable multifaceted insert and its wear. Having taken as an example cutting of graphite iron by the assembled cutting tools with replaceable multifaceted inserts the authors point at better power efficiency of high feeding cutting in comparison with high-speed cutting.

Erosion-resistant composite material

Science.gov (United States)

Finch, C.B.; Tennery, V.J.; Curlee, R.M.

A highly erosion-resistant composite material is formed of chemical vapor-deposited titanium diboride on a sintered titanium diboride-nickel substrate. This material may be suitable for use in cutting tools, coal liquefaction systems, etc.

The electrical resistivity method in cased boreholes

Energy Technology Data Exchange (ETDEWEB)

Schenkel, C.J.

1991-05-01

The use of downhole current sources in resistivity mapping can greatly enhance the detection and delineation of subsurface features. The purpose of this work is to examine the resistivity method for current sources in wells cased with steel. The resistivity method in cased boreholes with downhole current sources is investigated using the integral equation (IE) technique. The casing and other bodies are characterized as conductivity inhomogeneities in a half-space. For sources located along the casing axis, an axially symmetric Green's function is used to formulate the surface potential and electric field (E-field) volume integral equations. The situations involving off-axis current sources and three-dimensional (3-D) bodies is formulated using the surface potential IE method. The solution of the 3-D Green's function is presented in cylindrical and Cartesian coordinate systems. The methods of moments is used to solve the Fredholm integral equation of the second kind for the response due to the casing and other bodies. The numerical analysis revealed that the current in the casing can be approximated by its vertical component except near the source and the axial symmetric approximation of the casing is valid even for the 3-D problem. The E-field volume IE method is an effective and efficient technique to simulate the response of the casing in a half-space, whereas the surface potential approach is computationally better when multiple bodies are involved. Analyzing several configurations of the current source indicated that the casing response is influenced by four characteristic factors: conduction length, current source depth,casing depth, and casing length. 85 refs., 133 figs., 11 tabs.

KCUT, code to generate minimal cut sets for fault trees

International Nuclear Information System (INIS)

Han, Sang Hoon

2008-01-01

1 - Description of program or function: KCUT is a software to generate minimal cut sets for fault trees. 2 - Methods: Expand a fault tree into cut sets and delete non minimal cut sets. 3 - Restrictions on the complexity of the problem: Size and complexity of the fault tree

Elimination of striation in laser cutting of mild steel

International Nuclear Information System (INIS)

Sobih, M; Crouse, P L; Li, L

2007-01-01

High-power laser cutting is extensively used in many industrial applications. An important weakness of this process is the formation of striations (regular lines down the cut surface), which affect the quality of the surfaces produced. The elimination of striation formation is of considerable importance, since it could open up a variety of novel high-precision applications. This study presents the results of oxygen-assisted laser cutting of EN43 mild steel sheets, using a high-power fibre laser. Striation-free laser cuts are demonstrated for cutting 1 and 2 mm thick mild steel sheets. The optimal operating windows are presented and a mathematical method is proposed to estimate the critical speed at which striation-free cut can be obtained

Elimination of striation in laser cutting of mild steel

Energy Technology Data Exchange (ETDEWEB)

Sobih, M; Crouse, P L; Li, L [Laser Processing Research Centre, School of Mechanical, Aerospace and Civil Engineering, University of Manchester, Sackville Street Building, PO Box 88, Manchester M60 1QD (United Kingdom)

2007-11-21

High-power laser cutting is extensively used in many industrial applications. An important weakness of this process is the formation of striations (regular lines down the cut surface), which affect the quality of the surfaces produced. The elimination of striation formation is of considerable importance, since it could open up a variety of novel high-precision applications. This study presents the results of oxygen-assisted laser cutting of EN43 mild steel sheets, using a high-power fibre laser. Striation-free laser cuts are demonstrated for cutting 1 and 2 mm thick mild steel sheets. The optimal operating windows are presented and a mathematical method is proposed to estimate the critical speed at which striation-free cut can be obtaine000.

Design of Batch Distillation Columns Using Short-Cut Method at Constant Reflux

Directory of Open Access Journals (Sweden)

Asteria Narvaez-Garcia

2013-01-01

Full Text Available A short-cut method for batch distillation columns working at constant reflux was applied to solve a problem of four components that needed to be separated and purified to a mole fraction of 0.97 or better. Distillation columns with 10, 20, 30, 40, and 50 theoretical stages were used; reflux ratio was varied between 2 and 20. Three quality indexes were used and compared: Luyben’s capacity factor, total annual cost, and annual profit. The best combinations of theoretical stages and reflux ratio were obtained for each method. It was found that the best combinations always required reflux ratios close to the minimum. Overall, annual profit was the best quality index, while the best combination was a distillation column with 30 stages, and reflux ratio’s of 2.0 for separation of benzene (i, 5.0 for the separation of toluene (ii, and 20 for the separation of ethylbenzene (iii and purification of o-xylene (iv.

Flexible Laser Metal Cutting

DEFF Research Database (Denmark)

Villumsen, Sigurd; Jørgensen, Steffen Nordahl; Kristiansen, Morten

2014-01-01

This paper describes a new flexible and fast approach to laser cutting called ROBOCUT. Combined with CAD/CAM technology, laser cutting of metal provides the flexibility to perform one-of-a-kind cutting and hereby realises mass production of customised products. Today’s laser cutting techniques...... possess, despite their wide use in industry, limitations regarding speed and geometry. Research trends point towards remote laser cutting techniques which can improve speed and geometrical freedom and hereby the competitiveness of laser cutting compared to fixed-tool-based cutting technology...... such as punching. This paper presents the concepts and preliminary test results of the ROBOCUT laser cutting technology, a technology which potentially can revolutionise laser cutting....

DETERMINATION OF BRAKING OPTIMAL MODE OF CONTROLLED CUT OF DESIGN GROUP

Directory of Open Access Journals (Sweden)

A. S. Dorosh

2015-06-01

Full Text Available Purpose. The application of automation systems of breaking up process on the gravity hump is the efficiency improvement of their operation, absolute provision of trains breaking up safety demands, as well as improvement of hump staff working conditions. One of the main tasks of the indicated systems is the assurance of cuts reliable separation at all elements of their rolling route to the classification track. This task is a sophisticated optimization problem and has not received a final decision. Therefore, the task of determining the cuts braking mode is quite relevant. The purpose of this research is to find the optimal braking mode of control cut of design group. Methodology. In order to achieve the purpose is offered to use the direct search methods in the work, namely the Box complex method. This method does not require smoothness of the objective function, takes into account its limitations and does not require calculation of the function derivatives, and uses only its value. Findings. Using the Box method was developed iterative procedure for determining the control cut optimal braking mode of design group. The procedure maximizes the smallest controlled time interval in the group. To evaluate the effectiveness of designed procedure the series of simulation experiments of determining the control cut braking mode of design group was performed. The results confirmed the efficiency of the developed optimization procedure. Originality. The author formalized the task of optimizing control cut braking mode of design group, taking into account the cuts separation of design group at all elements (switches, retarders during cuts rolling to the classification track. The problem of determining the optimal control cut braking mode of design group was solved. The developed braking mode ensures cuts reliable separation of the group not only at the switches but at the retarders of brake position. Practical value. The developed procedure can be

Methods for Specific Electrode Resistance Measurement during Transcranial Direct Current Stimulation

Science.gov (United States)

Khadka, Niranjan; Rahman, Asif; Sarantos, Chris; Truong, Dennis Q.; Bikson, Marom

2014-01-01

Background Transcranial Direct Current Stimulation (tDCS) is investigated to treat a wide range of neuropsychiatric disorders, for rehabilitation, and for enhancing cognitive performance. The monitoring of electrode resistance before and during tDCS is considered important for tolerability and safety, where an unusually high resistance is indicative of undesired electrode or poor skin contact conditions. Conventional resistance measurement methods do not isolate individual electrode resistance but rather measures overall voltage. Moreover, for HD-tDCS devices, cross talk across electrodes makes concurrent resistance monitoring unreliable. Objective We propose a novel method for monitoring of the individual electrode resistance during tDCS, using a super-position of direct current with a test-signal (low-intensity and low-frequency sinusoids with electrode– specific frequencies) and a single sentinel electrode (not used for DC). Methods To validate this methodology, we developed lumped-parameter models of two and multi-electrode tDCS. Approaches with and without a sentinel electrode were solved and underlying assumptions identified. Assumptions were tested and parameterized in healthy participants using forearm stimulation combining tDCS (2 mA) and sinusoidal test-signals (38 μA and 76 μA peak to peak at 1 Hz, 10 Hz, and 100 Hz) and an in vitro test (where varied electrode failure modes were created). DC and AC component voltages across the electrodes were compared and participants were asked to rate subjective pain. Results A sentinel electrode is required to isolate electrode resistance in a two-electrode tDCS system. For multi-electrode resistance tracking, cross talk was aggravated with electrode proximity and current/resistance mismatches, but could be corrected using proposed approaches. Average voltage and average pain scores were not significantly different across test current intensities and frequencies (two-way repeated measures ANOVA) indicating the

Surface dimpling on rotating work piece using rotation cutting tool

Science.gov (United States)

Bhapkar, Rohit Arun; Larsen, Eric Richard

2015-03-31

A combined method of machining and applying a surface texture to a work piece and a tool assembly that is capable of machining and applying a surface texture to a work piece are disclosed. The disclosed method includes machining portions of an outer or inner surface of a work piece. The method also includes rotating the work piece in front of a rotating cutting tool and engaging the outer surface of the work piece with the rotating cutting tool to cut dimples in the outer surface of the work piece. The disclosed tool assembly includes a rotating cutting tool coupled to an end of a rotational machining device, such as a lathe. The same tool assembly can be used to both machine the work piece and apply a surface texture to the work piece without unloading the work piece from the tool assembly.

Research on cutting vibration characteristics of face-milling involute gear

Directory of Open Access Journals (Sweden)

Chengzhe JIN

2017-10-01

Full Text Available Traditional machining methods, such as gear hobbing, gear shaping and gear milling, etc, are commonly used for cutting machining of gear tooth profile, which cannot meet huge machining demand of gears to a certain extent. This article proposes to utilize a face-milling machining method in involute gear machining, which can be used to reduce production cost effectively. Cutting vibration generated during cutting machining has a direct effect on the machining accuracy and machined surface quality of workpiece. Therefore, it is desiderated to perform in-depth research regarding this issue. ADAMS software was used to establish a rigid-flexible coupling virtual prototyping model of face-milling gear milling system and a cutting vibration system model. Cutting vibration analysis was performed for face-milling gear by adopting quick sine frequency sweep method, so that the frequency response characteristics of workpiece in three directions X, Y and Z and space were acquired. The research results will provide reference and theoretical foundation for actual application of face-milling gear machining technology.

Effect of Cut Quality on Hybrid Laser Arc Welding of Thick Section Steels

Science.gov (United States)

Farrokhi, F.; Nielsen, S. E.; Schmidt, R. H.; Pedersen, S. S.; Kristiansen, M.

From an industrial point of view, in a laser cutting-welding production chain, it is of great importance to know the influence of the attainable laser cut quality on the subsequent hybrid laser arc welding process. Many studies have been carried out in the literature to obtain lower surface roughness values on the laser cut edge. However, in practice, the cost and reliability of the cutting process is crucial and it does not always comply with obtaining the highest surface quality. In this study, a number of experiments on 25 mm steel plates were carried out to evaluate the influence of cut surface quality on the final quality of the subsequent hybrid laser welded joints. The different cut surfaces were obtained by different industrial cutting methods including laser cutting, abrasive water cutting, plasma cutting, and milling. It was found that the mentioned cutting methods could be used as preparation processes for the subsequent hybrid laser arc welding. However, cut quality could determine the choice of process parameters of the following hybrid laser arc welding.

Some possibilities for determining cutting data when using laser cutting:

OpenAIRE

Radovanović, Miroslav

2006-01-01

The technological problems faced in the field of the application of laser-cutting machines lie in insufficient knowledge of the laser technique and the absence of both sufficiently reliable practical data and knowledge about the parameters affecting the work process itself. A significant parameter that is necessary to determine and to enter in an NC-program is the cutting speed. Various authors analyze the laser-cutting process and give mathematical models where laser cutting is modeled by us...

The optimization of the cutting process of diamonds with a YAG laser

Directory of Open Access Journals (Sweden)

A. J. Lubbe

1993-07-01

Full Text Available A laser cannot, as generally assumed by the layman, cut right through a diamond with a single cut. A couple of hundred cuts may be necessary to "chip carve" through a diamond. There are several parameters, for example cutting speed, focus point, overlapping of cuts, etc., that influence the cutting process. With a view to optimizing the cutting process, laser cuts in diamonds were studied in a systematic way with the aid of an electron microscope. The method, technique and the results of the research are discussed in this article.

Panel cutting method: new approach to generate panels on a hull in Rankine source potential approximation

Directory of Open Access Journals (Sweden)

Hee-Jong Choi

2011-12-01

Full Text Available In the present study, a new hull panel generation algorithm, namely panel cutting method, was developed to predict flow phenomena around a ship using the Rankine source potential based panel method, where the iterative method was used to satisfy the nonlinear free surface condition and the trim and sinkage of the ship was taken into account. Numerical computations were performed to investigate the validity of the proposed hull panel generation algorithm for Series 60 (CB=0.60 hull and KRISO container ship (KCS, a container ship designed by Maritime and Ocean Engineering Research Institute (MOERI. The computational results were validated by comparing with the existing experimental data.

Panel cutting method: new approach to generate panels on a hull in Rankine source potential approximation

Science.gov (United States)

Choi, Hee-Jong; Chun, Ho-Hwan; Park, Il-Ryong; Kim, Jin

2011-12-01

In the present study, a new hull panel generation algorithm, namely panel cutting method, was developed to predict flow phenomena around a ship using the Rankine source potential based panel method, where the iterative method was used to satisfy the nonlinear free surface condition and the trim and sinkage of the ship was taken into account. Numerical computations were performed to investigate the validity of the proposed hull panel generation algorithm for Series 60 (CB=0.60) hull and KRISO container ship (KCS), a container ship designed by Maritime and Ocean Engineering Research Institute (MOERI). The computational results were validated by comparing with the existing experimental data.

Modelling and Bi-objective Optimization of Soil Cutting and Pushing Process for Bulldozer and its Blade

Science.gov (United States)

Barakat, Nada; Sharma, Deepak

2017-12-01

Bulldozer is an earth moving machine, which is mainly used for cutting and pushing soil. The process of soil cutting and pushing involves various decisions making to make it optimum. The decisions are generally made based on the experience of practitioners that may not be optimum for different working conditions. In this paper, a bi-objective optimization problem is modelled so that the optimum values of decision variables can be determined. The objective functions are proposed to make the process economic and productive by minimizing the cutting force on a bulldozer blade and maximizing the blade capacity. A constraint is also developed on the power requirement from a bulldozer to overcome resistance. The problem is solved using ɛ-constraint method and multi-objective genetic algorithm. The approximate Pareto-optimal solutions and their perturbation analysis are presented. Various relationships are evolved from the post-optimal analysis that can be used for making guidelines for decision making for the process. The originality of this paper lies in developing the bi-objective formulation and in presenting various relationships by the post-optimal analysis, which has sparingly done in the domain literature.

Structure and adhesive properties of solid solution specimen surfaces based on bismuth tellurides after cutting

International Nuclear Information System (INIS)

Dik, M.G.; Rybina, L.N.; Dubrovina, A.N.; Abdinov, D.Sh.

1988-01-01

Structure and depth of broken layer, occuring at electroerosion cutting along ingot samples axis of Bi 2 Te 3 -Bi 2 Se 3 , Bi 2 Te 3 -Sb 2 Te 3 systems solid solutions (obtained by methods of directed crystallization and extrusion), and equilibrium contact angle θ, adhesion effort A and contact resistance r c of these crystals contacts with eutectic alloy of Bi-Sn system are investigated. Depth and structure of the broken layer were determined by means of stage-by-stage scouring-etching and X-ray investigation of cutting surface. It is shown, that etching during ∼50 c in large-block material eliminates polycrystalline layer, lattice bendings, resulting in Laue spots asterism, but does not remove their fragmentation and wash-out. Slots wash-out reduces, while fragmentation remains even after continuous etching. Etching with duration from ∼50 c up to 30-40 min practically does not change the character of polycrystalline samples diffraction pattern

Multibeam Fibre Laser Cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove

The appearance of the high power high brilliance fibre laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating cutting laser, the CO2-laser. However, quality problems in fibre......-laser cutting have until now limited its application in metal cutting. In this paper the first results of proof-of-principle studies applying a new approach (patent pending) for laser cutting with high brightness short wavelength lasers will be presented. In the approach, multi beam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from 2 single mode fibre lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W of single...

Multibeam fiber laser cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove; Hansen, Klaus Schütt; Nielsen, Jakob Skov

2009-01-01

The appearance of the high power high brilliance fiber laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating Cutting laser, the CO2 laser. However, quality problems in fiber......-laser cutting have until now limited its application to metal cutting. In this paper the first results of proof-of-principle Studies applying a new approach (patent pending) for laser cutting with high brightness and short wavelength lasers will be presented. In the approach, multibeam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from two single mode fiber lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W...

Cut-elimination for the mu-calculus with one variable

Directory of Open Access Journals (Sweden)

Grigori Mints

2012-02-01

Full Text Available We establish syntactic cut-elimination for the one-variable fragment of the modal mu-calculus. Our method is based on a recent cut-elimination technique by Mints that makes use of Buchholz' Omega-rule.

Cutting cleaner

International Nuclear Information System (INIS)

Elsen, R.P.H. van; Smits, M.

1991-01-01

This paper presents the results of a long term field test of the Cutting Cleaner, which is used for the treatment of wet oil contaminated cuttings (WOCC) produced when drilling with Oil Based Mud (OBM). It was concluded that it is possible to reduce the oil content of cuttings to an average of 1 - 2%. The recovered base oil can be reused to make new oil based mud

Methods for quantifying adipose tissue insulin resistance in overweight/obese humans.

Science.gov (United States)

Ter Horst, K W; van Galen, K A; Gilijamse, P W; Hartstra, A V; de Groot, P F; van der Valk, F M; Ackermans, M T; Nieuwdorp, M; Romijn, J A; Serlie, M J

2017-08-01

Insulin resistance of adipose tissue is an important feature of obesity-related metabolic disease. However, assessment of lipolysis in humans requires labor-intensive and expensive methods, and there is limited validation of simplified measurement methods. We aimed to validate simplified methods for the quantification of adipose tissue insulin resistance against the assessment of insulin sensitivity of lipolysis suppression during hyperinsulinemic-euglycemic clamp studies. We assessed the insulin-mediated suppression of lipolysis by tracer-dilution of [1,1,2,3,3- 2 H 5 ]glycerol during hyperinsulinemic-euglycemic clamp studies in 125 overweight or obese adults (85 men, 40 women; age 50±11 years; body mass index 38±7 kg m -2 ). Seven indices of adipose tissue insulin resistance were validated against the reference measurement method. Low-dose insulin infusion resulted in suppression of the glycerol rate of appearance ranging from 4% (most resistant) to 85% (most sensitive), indicating a good range of adipose tissue insulin sensitivity in the study population. The reference method correlated with (1) insulin-mediated suppression of plasma glycerol concentrations (r=0.960, PInsulin Resistance (Adipo-IR) index (fasting plasma insulin-NEFA product; r=-0.526, Pinsulin-glycerol product (r=-0.467, PInsulin Resistance Index (fasting plasma insulin-basal lipolysis product; r=0.460, PInsulin Sensitivity Check Index (QUICKI)-NEFA index (r=0.621, Pinsulin resistance (area under the curve ⩾0.801, Pinsulin sensitivity (that is, the antilipolytic action of insulin) can be reliably quantified in overweight and obese humans by simplified index methods. The sensitivity and specificity of the Adipo-IR index and the fasting plasma insulin-glycerol product, combined with their simplicity and acceptable agreement, suggest that these may be most useful in clinical practice.

Graph-cut based discrete-valued image reconstruction.

Science.gov (United States)

Tuysuzoglu, Ahmet; Karl, W Clem; Stojanovic, Ivana; Castañòn, David; Ünlü, M Selim

2015-05-01

Efficient graph-cut methods have been used with great success for labeling and denoising problems occurring in computer vision. Unfortunately, the presence of linear image mappings has prevented the use of these techniques in most discrete-amplitude image reconstruction problems. In this paper, we develop a graph-cut based framework for the direct solution of discrete amplitude linear image reconstruction problems cast as regularized energy function minimizations. We first analyze the structure of discrete linear inverse problem cost functions to show that the obstacle to the application of graph-cut methods to their solution is the variable mixing caused by the presence of the linear sensing operator. We then propose to use a surrogate energy functional that overcomes the challenges imposed by the sensing operator yet can be utilized efficiently in existing graph-cut frameworks. We use this surrogate energy functional to devise a monotonic iterative algorithm for the solution of discrete valued inverse problems. We first provide experiments using local convolutional operators and show the robustness of the proposed technique to noise and stability to changes in regularization parameter. Then we focus on nonlocal, tomographic examples where we consider limited-angle data problems. We compare our technique with state-of-the-art discrete and continuous image reconstruction techniques. Experiments show that the proposed method outperforms state-of-the-art techniques in challenging scenarios involving discrete valued unknowns.

CO 2 laser cutting of MDF . 2. Estimation of power distribution

Science.gov (United States)

Ng, S. L.; Lum, K. C. P.; Black, I.

2000-02-01

Part 2 of this paper details an experimentally-based method to evaluate the power distribution for both CW and PM cutting. Variations in power distribution with different cutting speeds, material thickness and pulse ratios are presented. The paper also provides information on both the cutting efficiency and absorptivity index for MDF, and comments on the beam dispersion characteristics after the cutting process.

Laser cutting or water-jet cutting. Laser setsudan ka water-jet setsudan ka

Energy Technology Data Exchange (ETDEWEB)

Yamada, T. (Shibuya Kogyo Co. Ltd., Ishikawa (Japan))

1991-05-01

The recent spread of carbon oxide laser cutter is so startlingly fast, but at the same time, water jet cutting using ultra high pressure water stream is drawing attention as it has identical characteristics, and opens the way to cutting materials that have been hitherto difficult to cut. The authors, who are fabricators of cutters of both types, gave the comparisons and explanations on several examples referring to materials that can be cut, cutting accuracy, speed, shape and thermal effects to cut face, and running cost in detail. However, simple comparison is difficult. For instance, cutting 6 mm thick SUS sheet costs a running cost of 65 yen per meter in laser cutting, and 535 yen per meter in water jet cutting, but this situation is often reversed when other material or sheet thickness is selected. The actual situation in the sheet metal processing industry at the present time is that it uses by far more laser processing machines, and uses water jet cutters to supplement for cutting materials more difficult to cut. 10 figs., 3 tabs.

Forecasting grain size distribution of coal cut by a shearer loader

Energy Technology Data Exchange (ETDEWEB)

Sikora, W; Chodura, J; Siwiec, J

1983-02-01

Analyzed are effects of shearer loader design on grain size distribution of coal, particularly on proportion of the finest size group and proportion of largest coal grains. The method developed by the IGD im. A.A. Skochinski Institute in Moscow is used. Effects of cutting tool design and mechanical coal properties are analyzed. Of the evaluated factors, two are of decisive importance: thickness of the coal chip cut by a cutting tool and coefficient of coal disintegration which characterizes coal behavior during cutting. Grain size distribution is also influenced by cutting tool geometry. Two elements of cutting tool design are of major importance: dimensions of the cutting edge and angle of attack. Effects of cutting tool design and coal mechanical properties on grain size distribution are shown in 12 diagrams. Using the forecasting method developed by the IGD im. A.A. Skochinski Institute in Moscow grain size distribution of coal cut by three shearer loaders is calculated: the KWB-3RDU with a drum 1600 mm in diameter, the KWB-6W with a drum 2500 mm in diameter, and a shearer loader being developed with a 1550 mm drum. The results of comparative evaluations are shown in two tables. 5 references.

ENVIRONMENTALLY REDUCING OF COOLANTS IN METAL CUTTING

Directory of Open Access Journals (Sweden)

Veijo KAUPPINEN

2012-11-01

Full Text Available Strained environment is a global problem. In metal industries the use of coolant has become more problematic in terms of both employee health and environmental pollution. It is said that the use of coolant forms approximately 8 - 16 % of the total production costs.The traditional methods that use coolants are now obviously becoming obsolete. Hence, it is clear that using a dry cutting system has great implications for resource preservation and waste reduction. For this purpose, a new cooling system is designed for dry cutting. This paper presents the new eco-friendly cooling innovation and the benefits gained by using this method. The new cooling system relies on a unit for ionising ejected air. In order to compare the performance of using this system, cutting experiments were carried out. A series of tests were performed on a horizontal turning machine and on a horizontal machining centre.

Algorithm for finding minimal cut sets in a fault tree

International Nuclear Information System (INIS)

Rosenberg, Ladislav

1996-01-01

This paper presents several algorithms that have been used in a computer code for fault-tree analysing by the minimal cut sets method. The main algorithm is the more efficient version of the new CARA algorithm, which finds minimal cut sets with an auxiliary dynamical structure. The presented algorithm for finding the minimal cut sets enables one to do so by defined requirements - according to the order of minimal cut sets, or to the number of minimal cut sets, or both. This algorithm is from three to six times faster when compared with the primary version of the CARA algorithm

The perfection of the construction of a combined cutting tool on the basis of the results of mathematical modelling of working cutting processes in RecurDyn

Directory of Open Access Journals (Sweden)

Poddubny Vladimir

2017-01-01

Full Text Available As the title implies the article describes how to optimize the construction of a combined cutting tool on the example of developed design of the face milling cutter with regulable rigidity of damping elements in order to improve the vibration resistance of the cutting process. RecurDyn is proposed, which is widely used for creating models of different mechanical systems, their analysis and optimization of construction, uses the ideology of visual object-oriented programming and computer research of volume solid-state models. Much attention is given to the description of the mechanical and mathematical model of the face milling cutter in RecurDyn and the results of mathematical modeling of the face milling cutter with damping elements, consisting of individual elements, with the possibility of program controlling its operation in the process of cutting. The applying of RecurDyn made it possible to carry out a complex assessment of influence of separate elements of a design of the combined cutting tool on quantitative and qualitative parameters of milling process and to define optimal values of the input and output parameters of technological process of machining for various damping elements.

Technology development for cutting a reactor pressure vessel using a mechanical cutting technique

International Nuclear Information System (INIS)

Watanabe, Masaaki; Miyasaka, Yasuhiko; Miyao, Hidehiko; Ooki, Arahiko; Ninomiya, Toshiaki; Koiwai, Masami

2001-01-01

On decommissioning of nuclear facilities, the thermal cutting technique such as an oxygen-acetylene gas cutting and a plasma arc cutting are generally used for cutting massive and thick steel structures in consideration with cutting speed and control performance. These techniques generate dust, smoke, aerosol and a large quantity of secondary waste. Mechanical cutting technique has an advantage of small amount of secondary waste, and the metal chips from the kerf recovered easily compared with these thermal cutting technique. The remote mechanical cutting system for highly activated RPV has been developed with the manner which achieves the safety and cost effectiveness. The development has been performed on consignment to RANDEC from the Science and Technology Agency of Japan. (author)

A review on ductile mode cutting of brittle materials

Science.gov (United States)

Antwi, Elijah Kwabena; Liu, Kui; Wang, Hao

2018-06-01

Brittle materials have been widely employed for industrial applications due to their excellent mechanical, optical, physical and chemical properties. But obtaining smooth and damage-free surface on brittle materials by traditional machining methods like grinding, lapping and polishing is very costly and extremely time consuming. Ductile mode cutting is a very promising way to achieve high quality and crack-free surfaces of brittle materials. Thus the study of ductile mode cutting of brittle materials has been attracting more and more efforts. This paper provides an overview of ductile mode cutting of brittle materials including ductile nature and plasticity of brittle materials, cutting mechanism, cutting characteristics, molecular dynamic simulation, critical undeformed chip thickness, brittle-ductile transition, subsurface damage, as well as a detailed discussion of ductile mode cutting enhancement. It is believed that ductile mode cutting of brittle materials could be achieved when both crack-free and no subsurface damage are obtained simultaneously.

ESF SOUTH PORTAL BOX-CUT/HIGHWALL STABILITY ANALYSIS (SCPB:N/A)

International Nuclear Information System (INIS)

Saeed Bonabian

1996-01-01

The main purpose and objective of this analysis is to design a Box-Cut at the ESF South Portal to accommodate the Tunnel Boring Machine's (TBM) exit at the conclusion of the ESF Main Loop construction. The stability of the Highwall and the sidewalls at the Box-Cut are assessed using analytical methods by numerical modeling techniques. A ground reinforcement system for the South Ramp Box-Cut slopes will be recommended. This report summarizes the results of the analyses and provides the details of the recommended ground reinforcement system for the Box-Cut slopes at the South Portal. The reinforcement design details are then incorporated into design output documents for implementation in the field. Method of excavation for the Box-Cut is also discussed and a recommendation is provided in this analysis

Analyses of Effects of Cutting Parameters on Cutting Edge Temperature Using Inverse Heat Conduction Technique

Directory of Open Access Journals (Sweden)

Marcelo Ribeiro dos Santos

2014-01-01

Full Text Available During machining energy is transformed into heat due to plastic deformation of the workpiece surface and friction between tool and workpiece. High temperatures are generated in the region of the cutting edge, which have a very important influence on wear rate of the cutting tool and on tool life. This work proposes the estimation of heat flux at the chip-tool interface using inverse techniques. Factors which influence the temperature distribution at the AISI M32C high speed steel tool rake face during machining of a ABNT 12L14 steel workpiece were also investigated. The temperature distribution was predicted using finite volume elements. A transient 3D numerical code using irregular and nonstaggered mesh was developed to solve the nonlinear heat diffusion equation. To validate the software, experimental tests were made. The inverse problem was solved using the function specification method. Heat fluxes at the tool-workpiece interface were estimated using inverse problems techniques and experimental temperatures. Tests were performed to study the effect of cutting parameters on cutting edge temperature. The results were compared with those of the tool-work thermocouple technique and a fair agreement was obtained.

Wave resistance calculation method combining Green functions based on Rankine and Kelvin source

Directory of Open Access Journals (Sweden)

LI Jingyu

2017-12-01

Full Text Available [Ojectives] At present, the Boundary Element Method(BEM of wave-making resistance mostly uses a model in which the velocity distribution near the hull is solved first, and the pressure integral is then calculated using the Bernoulli equation. However,the process of this model of wave-making resistance is complex and has low accuracy.[Methods] To address this problem, the present paper deduces a compound method for the quick calculation of ship wave resistance using the Rankine source Green function to solve the hull surface's source density, and combining the Lagally theorem concerning source point force calculation based on the Kelvin source Green function so as to solve the wave resistance. A case for the Wigley model is given.[Results] The results show that in contrast to the thin ship method of the linear wave resistance theorem, this method has higher precision, and in contrast to the method which completely uses the Kelvin source Green function, this method has better computational efficiency.[Conclusions] In general, the algorithm in this paper provides a compromise between precision and efficiency in wave-making resistance calculation.

Machining of Some Difficult-to-Cut Materials with Rotary Cutting Tools

OpenAIRE

Stjernstoft, Tero

2004-01-01

Automobile and aero industries have an increasing interestin materials with improved mechanical properties. However, manyof these new materials are classified as difficult-to-cut withconventional tools. It is obvious that tools, cutting processesand cutting models has to be devel-oped parallel to materialsscience. In this thesis rotary cutting tools are tested as analternative toexpensive diamond or cubic bore nitridetools. Metal matrix composites mostly consist of a light metalalloy (such as...

Identification of cutting force coefficients in machining process considering cutter vibration

Science.gov (United States)

Yao, Qi; Luo, Ming; Zhang, Dinghua; Wu, Baohai

2018-03-01

Among current cutting force models, cutting force coefficients still are the foundation of predicting calculation combined with consideration of geometry engagement variation, equipment characteristics, material properties and so on. Attached with unimpeachable significance, the traditional and some novel identification methods of cutting force coefficient are still faced with trouble, including repeated onerous work, over ideal measuring condition, variation of value due to material divergence, interference from measuring units. To utilize the large amount of data from real manufacturing section, enlarge data sources and enrich cutting data base for former prediction task, a novel identification method is proposed by considering stiffness properties of the cutter-holder-spindle system in this paper. According to previously proposed studies, the direct result of cutter vibration is the form of dynamic undeformed chip thickness. This fluctuation is considered in two stages of this investigation. Firstly, a cutting force model combined with cutter vibration is established in detailed way. Then, on the foundation of modeling, a novel identification method is developed, in which the dynamic undeformed chip thickness could be obtained by using collected data. In a carefully designed experiment procedure, the reliability of model is validated by comparing predicted and measured results. Under different cutting condition and cutter stiffness, data is collected for the justification of identification method. The results showed divergence in calculated coefficients is acceptable confirming the possibility of accomplishing targets by applying this new method. In discussion, the potential directions of improvement are proposed.

Method of making sulfur-resistant composite metal membranes

Science.gov (United States)

Way, J Douglas [Boulder, CO; Lusk, Mark [Golden, CO; Thoen, Paul [Littleton, CO

2012-01-24

The invention provides thin, hydrogen-permeable, sulfur-resistant membranes formed from palladium or palladium-alloy coatings on porous, ceramic or metal supports. Also disclosed are methods of making these membranes via sequential electroless plating techniques, wherein the method of making the membrane includes decomposing any organic ligands present on the substrate, reducing the palladium crystallites on the substrate to reduced palladium crystallites, depositing a film of palladium metal on the substrate and then depositing a second, gold film on the palladium film. These two metal films are then annealed at a temperature between about 200.degree. C. and about 1200.degree. C. to form a sulfur-resistant, composite PdAu alloy membrane.

Minimizing waste (off-cuts using cutting stock model: The case of one dimensional cutting stock problem in wood working industry

Directory of Open Access Journals (Sweden)

Gbemileke A. Ogunranti

2016-09-01

Full Text Available Purpose: The main objective of this study is to develop a model for solving the one dimensional cutting stock problem in the wood working industry, and develop a program for its implementation. Design/methodology/approach: This study adopts the pattern oriented approach in the formulation of the cutting stock model. A pattern generation algorithm was developed and coded using Visual basic.NET language. The cutting stock model developed is a Linear Programming (LP Model constrained by numerous feasible patterns. A LP solver was integrated with the pattern generation algorithm program to develop a one - dimensional cutting stock model application named GB Cutting Stock Program. Findings and Originality/value: Applying the model to a real life optimization problem significantly reduces material waste (off-cuts and minimizes the total stock used. The result yielded about 30.7% cost savings for company-I when the total stock materials used is compared with the former cutting plan. Also, to evaluate the efficiency of the application, Case I problem was solved using two top commercial 1D-cutting stock software.  The results show that the GB program performs better when related results were compared. Research limitations/implications: This study round up the linear programming solution for the number of pattern to cut. Practical implications: From Managerial perspective, implementing optimized cutting plans increases productivity by eliminating calculating errors and drastically reducing operator mistakes. Also, financial benefits that can annually amount to millions in cost savings can be achieved through significant material waste reduction. Originality/value: This paper developed a linear programming one dimensional cutting stock model based on a pattern generation algorithm to minimize waste in the wood working industry. To implement the model, the algorithm was coded using VisualBasic.net and linear programming solver called lpsolvedll (dynamic

Optimisation of the Laser Cutting Process

DEFF Research Database (Denmark)

Dragsted, Birgitte; Olsen, Flemmming Ove

1996-01-01

The problem in optimising the laser cutting process is outlined. Basic optimisation criteria and principles for adapting an optimisation method, the simplex method, are presented. The results of implementing a response function in the optimisation are discussed with respect to the quality as well...

Application of column tests and electrical resistivity methods for leachate transport monitoring

Directory of Open Access Journals (Sweden)

Wychowaniak Dorota

2015-09-01

Full Text Available Development of the human civilization leads to the pollution of environment. One of the contamination which are a real threat to soil and groundwater are leachates from landfills. In this paper the solute transport through soil was considered. For this purpose, the laboratory column tests of chlorides tracer and leachates transport on two soil samples have been carried out. Furthermore, the electrical resistivity method was applied as auxiliary tool to follow the movements of solute through the soil column what allowed to compare between the results obtained with column test method and electrical resistivity measurements. Breakthrough curves obtained by conductivity and resistivity methods represents similar trends which leads to the conclusion about the suitability of electrical resistivity methods for contamination transport monitoring in soil-water systems.

Study on underwater plasma arc cutting technology

International Nuclear Information System (INIS)

Yada, Toshio; Nakamura, Uhachiro; Tomidokoro, Sakae; Fukuzawa, Mitsuo

1980-01-01

The zirconium alloy tube of the impile creep test facility had been subjected to inner pressure in the Japan Material Testing Reactor (JMTR) environment. In the near future, it will be necessary to dismantle the facility and to take out the tube for such examinations as irradiation effects on material properties. In order to establish the dismantling technology for the radioactive facility, a study on underwater plasma arc cutting has been carried out since 1977. Primarily, optimum underwater cutting sequence and conditions were studied in details for developing the remote control handling and the cutting system. Further, the amounts of particles suspended in water as well as those contained in bubbled gas were quantitatively analyzed for developing a safe removal system for contaminants which were produced by cutting the radioactive material. As a result of this study, it has been concluded that the underwater plasma arc cutting method is generally suitable and effective for dismantling such radioactive material as the impile creep test facility of the JMTR. (author)

Preparation of Road Cuts by Usage of Drilling and Blasting Works

OpenAIRE

Dambov, Risto; Mijoski, Goran; Karanakova Stefanovska, Radmila

2011-01-01

This paper shows the basic methods of blasting in the construction of the (one-sided and double sided) road cuts in hilly terrain with different inclinations. By applying of these methods we get stable slopes of manufactured road cuts, minimal (or no) damage of the rest solid rocks. It is important to emphasize that the stable and undeformed slopes of the road cuts, to avoid the additional work of restoration and protection of slopes from landslides on the road. The application of these...

Trend of CO2 laser cutting; Saikin no CO2 laser setsudan

Energy Technology Data Exchange (ETDEWEB)

Fujii, T.; Sano, Y.; Nagahori, M. [Tanaka Engineering Works Ltd., Saitama (Japan)

1998-08-01

This paper describes CO2 laser cutting of medium thick plates. Carbon dioxide laser is mainly used for laser generators. The generation efficiency of CO2 laser is 5 to 15% which is higher than that of the other lasers. Ninety percent of the usage is for cutting, piercing and welding. Laser cutter having a separated generator with a power from 3 to 6 kW is often used for cutting medium thick plates. The recent trend of new cutting technology is introduced. When power is increased from 3 kW to 6 kW without using oxygen as assist gas, the cutting thickness of stainless steel plate increased into 1.5 times, and the cutting speed increased into 1.5 to 2 times. For the soft steel members with black coating in which the power-up effects have not been obtained, the cutting speed, quality of cutting surface and cutting stability were improved by introducing new technology. Piercing time has been reduced by developing a method by which pulse generation is changed during piercing and a method by which piercing is conducted by irradiating the maximum power of continuous generation. Cutting quality with high accuracy has been realized by developing light weight generator and high performance NC unit. 10 figs.

STRUCTURAL ANNOTATION OF EM IMAGES BY GRAPH CUT

Energy Technology Data Exchange (ETDEWEB)

Chang, Hang; Auer, Manfred; Parvin, Bahram

2009-05-08

Biological images have the potential to reveal complex signatures that may not be amenable to morphological modeling in terms of shape, location, texture, and color. An effective analytical method is to characterize the composition of a specimen based on user-defined patterns of texture and contrast formation. However, such a simple requirement demands an improved model for stability and robustness. Here, an interactive computational model is introduced for learning patterns of interest by example. The learned patterns bound an active contour model in which the traditional gradient descent optimization is replaced by the more efficient optimization of the graph cut methods. First, the energy function is defined according to the curve evolution. Next, a graph is constructed with weighted edges on the energy function and is optimized with the graph cut algorithm. As a result, the method combines the advantages of the level set method and graph cut algorithm, i.e.,"topological" invariance and computational efficiency. The technique is extended to the multi-phase segmentation problem; the method is validated on synthetic images and then applied to specimens imaged by transmission electron microscopy(TEM).

Generation of segmental chips in metal cutting modeled with the PFEM

Science.gov (United States)

Rodriguez Prieto, J. M.; Carbonell, J. M.; Cante, J. C.; Oliver, J.; Jonsén, P.

2017-09-01

The Particle Finite Element Method, a lagrangian finite element method based on a continuous Delaunay re-triangulation of the domain, is used to study machining of Ti6Al4V. In this work the method is revised and applied to study the influence of the cutting speed on the cutting force and the chip formation process. A parametric methodology for the detection and treatment of the rigid tool contact is presented. The adaptive insertion and removal of particles are developed and employed in order to sidestep the difficulties associated with mesh distortion, shear localization as well as for resolving the fine-scale features of the solution. The performance of PFEM is studied with a set of different two-dimensional orthogonal cutting tests. It is shown that, despite its Lagrangian nature, the proposed combined finite element-particle method is well suited for large deformation metal cutting problems with continuous chip and serrated chip formation.

A mathematical model and an approximate method for calculating the fracture characteristics of nonmetallic materials during laser cutting

Energy Technology Data Exchange (ETDEWEB)

Smorodin, F.K.; Druzhinin, G.V.

1991-01-01

A mathematical model is proposed which describes the fracture behavior of amorphous materials during laser cutting. The model, which is based on boundary layer equations, is reduced to ordinary differential equations with the corresponding boundary conditions. The reduced model is used to develop an approximate method for calculating the fracture characteristics of nonmetallic materials.

Simple PCR assays improve the sensitivity of HIV-1 subtype B drug resistance testing and allow linking of resistance mutations.

Directory of Open Access Journals (Sweden)

Jeffrey A Johnson

Full Text Available BACKGROUND: The success of antiretroviral therapy is known to be compromised by drug-resistant HIV-1 at frequencies detectable by conventional bulk sequencing. Currently, there is a need to assess the clinical consequences of low-frequency drug resistant variants occurring below the detection limit of conventional genotyping. Sensitive detection of drug-resistant subpopulations, however, requires simple and practical methods for routine testing. METHODOLOGY: We developed highly-sensitive and simple real-time PCR assays for nine key drug resistance mutations and show that these tests overcome substantial sequence heterogeneity in HIV-1 clinical specimens. We specifically used early wildtype virus samples from the pre-antiretroviral drug era to measure background reactivity and were able to define highly-specific screening cut-offs that are up to 67-fold more sensitive than conventional genotyping. We also demonstrate that sequencing the mutation-specific PCR products provided a direct and novel strategy to further detect and link associated resistance mutations, allowing easy identification of multi-drug-resistant variants. Resistance mutation associations revealed in mutation-specific amplicon sequences were verified by clonal sequencing. SIGNIFICANCE: Combined, sensitive real-time PCR testing and mutation-specific amplicon sequencing provides a powerful and simple approach that allows for improved detection and evaluation of HIV-1 drug resistance mutations.

Underwater cutting techniques developments

International Nuclear Information System (INIS)

Bach, F.-W.

1990-01-01

The primary circuit structures of different nuclear powerplants are constructed out of stainless steels, ferritic steels, plated ferritic steels and alloys of aluminium. According to the level of the specific radiation of these structures, it is necessary for dismantling to work with remote controlled cutting techniques. The most successful way to protect the working crew against exposure of radiation is to operate underwater in different depths. The following thermal cutting processes are more or less developed to work under water: For ferritic steels only - flame cutting; For ferritic steels, stainless steels, cladded steels and aluminium alloys - oxy-arc-cutting, arc-waterjet-cutting with a consumable electrode, arc-saw-cutting, plasma-arc-cutting and plasma-arc-saw. The flame cutting is a burning process, all the other processes are melt-cutting processes. This paper explains the different techniques, giving a short introduction of the theory, a discussion of the possibilities with the advantages and disadvantages of these processes giving a view into the further research work in this interesting field. (author)

Standard method for detecting Bombyx mori nucleopolyhedrovirus disease-resistant silkworm varieties

Directory of Open Access Journals (Sweden)

Yang Qiong

Full Text Available ABSTRACT Bombyx mori nucleopolyhedrovirus (BmNPV disease is one of the most serious silkworm diseases, and it has caused great economic losses to the sericulture industry. So far, the disease has not been controlled effectively by therapeutic agents. Breeding resistant silkworm varieties breeding may be an effective way to improve resistance to BmNPV and reduce economic losses. A precise resistance-detection method will help to accelerate the breeding process. For this purpose, here we described the individual inoculation method (IIM. Details of the IIM include pathogen BmNPV preparation, mulberry leaf size, pathogen volume, rearing conditions, course of infection, and breeding conditions. Finally, a resistance comparison experiment was performed using the IIM and the traditional group inoculation method (GIM. The incidence of BmNPV infection and the within-group variance results showed that the IIM was more precise and reliable than the GIM.

SurfCut: Free-Boundary Surface Extraction

KAUST Repository

Algarni, Marei Saeed Mohammed

2016-09-15

We present SurfCut, an algorithm for extracting a smooth simple surface with unknown boundary from a noisy 3D image and a seed point. In contrast to existing approaches that extract smooth simple surfaces with boundary, our method requires less user input, i.e., a seed point, rather than a 3D boundary curve. Our method is built on the novel observation that certain ridge curves of a front propagated using the Fast Marching algorithm are likely to lie on the surface. Using the framework of cubical complexes, we design a novel algorithm to robustly extract such ridge curves and form the surface of interest. Our algorithm automatically cuts these ridge curves to form the surface boundary, and then extracts the surface. Experiments show the robustness of our method to errors in the data, and that we achieve higher accuracy with lower computational cost than comparable methods. © Springer International Publishing AG 2016.

Critical test of isotropic periodic sum techniques with group-based cut-off schemes.

Science.gov (United States)

Nozawa, Takuma; Yasuoka, Kenji; Takahashi, Kazuaki Z

2018-03-08

Truncation is still chosen for many long-range intermolecular interaction calculations to efficiently compute free-boundary systems, macromolecular systems and net-charge molecular systems, for example. Advanced truncation methods have been developed for long-range intermolecular interactions. Every truncation method can be implemented as one of two basic cut-off schemes, namely either an atom-based or a group-based cut-off scheme. The former computes interactions of "atoms" inside the cut-off radius, whereas the latter computes interactions of "molecules" inside the cut-off radius. In this work, the effect of group-based cut-off is investigated for isotropic periodic sum (IPS) techniques, which are promising cut-off treatments to attain advanced accuracy for many types of molecular system. The effect of group-based cut-off is clearly different from that of atom-based cut-off, and severe artefacts are observed in some cases. However, no severe discrepancy from the Ewald sum is observed with the extended IPS techniques.

Computational methods for structural load and resistance modeling

Science.gov (United States)

Thacker, B. H.; Millwater, H. R.; Harren, S. V.

1991-01-01

An automated capability for computing structural reliability considering uncertainties in both load and resistance variables is presented. The computations are carried out using an automated Advanced Mean Value iteration algorithm (AMV +) with performance functions involving load and resistance variables obtained by both explicit and implicit methods. A complete description of the procedures used is given as well as several illustrative examples, verified by Monte Carlo Analysis. In particular, the computational methods described in the paper are shown to be quite accurate and efficient for a material nonlinear structure considering material damage as a function of several primitive random variables. The results show clearly the effectiveness of the algorithms for computing the reliability of large-scale structural systems with a maximum number of resolutions.

Cutting assembly

Science.gov (United States)

Racki, Daniel J.; Swenson, Clark E.; Bencloski, William A.; Wineman, Arthur L.

1984-01-01

A cutting apparatus includes a support table mounted for movement toward and away from a workpiece and carrying a mirror which directs a cutting laser beam onto the workpiece. A carrier is rotatably and pivotally mounted on the support table between the mirror and workpiece and supports a conduit discharging gas toward the point of impingement of the laser beam on the workpiece. Means are provided for rotating the carrier relative to the support table to place the gas discharging conduit in the proper positions for cuts made in different directions on the workpiece.

Optimal cut-off values for the homeostasis model assessment of insulin resistance (HOMA-IR) and pre-diabetes screening: Developments in research and prospects for the future.

Science.gov (United States)

Tang, Qi; Li, Xueqin; Song, Peipei; Xu, Lingzhong

2015-12-01

Diabetes mellitus (DM) appears to be increasing rapidly, threatening to reduce life expectancy for humans around the globe. The International Diabetes Federation (IDF) has estimated that there will be 642 million people living with the disease by 2040 and half as many again who will be not diagnosed. This means that pre-DM screening is a critical issue. Insulin resistance (IR) has emerged as a major pathophysiological factor in the development and progression of DM since it is evident in susceptible individuals at the early stages of DM, and particularly type 2 DM (T2DM). Therefore, assessment of IR via the homeostasis model assessment of IR (HOMA-IR) is a key index for the primary prevention of DM and is thus found in guidelines for screening of high-risk groups. However, the cut-off values of HOMA-IR differ for different races, ages, genders, diseases, complications, etc. due to the complexity of IR. This hampers the determination of specific cut-off values of HOMA-IR in different places and in different situations. China has not published an official index to gauge IR for primary prevention of T2DM in the diabetic and non-diabetic population except for children and adolescents ages 6-12 years. Hence, this article summarizes developments in research on IR, HOMA-IR, and pre-DM screening in order to provide a reference for optimal cut-off values of HOMA-IR for the diagnosis of DM in the Chinese population.

On Computations of Duct Acoustics with Near Cut-Off Frequency

Science.gov (United States)

Dong, Thomas Z.; Povinelli, Louis A.

1997-01-01

The cut-off is a unique feature associated with duct acoustics due to the presence of duct walls. A study of this cut-off effect on the computations of duct acoustics is performed in the present work. The results show that the computation of duct acoustic modes near cut-off requires higher numerical resolutions than others to avoid being numerically cut off. Duct acoustic problems in Category 2 are solved by the DRP finite difference scheme with the selective artificial damping method and results are presented and compared to reference solutions.

Restraining and neck cutting or stunning and neck cutting of veal calves.

Science.gov (United States)

Lambooij, E; van der Werf, J T N; Reimert, H G M; Hindle, V A

2012-05-01

Brain and heart activities were measured in 31 veal calves during restraining and rotating followed by neck cutting with or without stunning to evaluate welfare. After neck cutting correlation dimension analyses and %power of EEG beta wave fraction decreased gradually to lower values resulting in an induction of unconsciousness lasting on average 80s. Corneal reflex response ceased 135±57s after neck cutting. The CD scores and the %power of beta waves fell immediately after post-cut captive bolt and pre-cut electrical stunning to levels indicating unconsciousness. Heart rate in lairage increased upon entrance to the restrainer and again after rotation, heart rate variability decreased. Rotating the restrainer 90°, 120° or 180° compromised veal calf welfare and should be avoided. It is recommended to use post-cut captive bolt stunning or pre-cut electrical stunning inducing immediate unconsciousness. Copyright © 2011 Elsevier Ltd. All rights reserved.

Numerical simulation of rock cutting using 2D AUTODYN

International Nuclear Information System (INIS)

Woldemichael, D E; Rani, A M Abdul; Lemma, T A; Altaf, K

2015-01-01

In a drilling process for oil and gas exploration, understanding of the interaction between the cutting tool and the rock is important for optimization of the drilling process using polycrystalline diamond compact (PDC) cutters. In this study the finite element method in ANSYS AUTODYN-2D is used to simulate the dynamics of cutter rock interaction, rock failure, and fragmentation. A two-dimensional single PDC cutter and rock model were used to simulate the orthogonal cutting process and to investigate the effect of different parameters such as depth of cut, and back rake angle on two types of rocks (sandstone and limestone). In the simulation, the cutting tool was dragged against stationary rock at predetermined linear velocity and the depth of cut (1,2, and 3 mm) and the back rake angles(-10°, 0°, and +10°) were varied. The simulation result shows that the +10° back rake angle results in higher rate of penetration (ROP). Increasing depth of cut leads to higher ROP at the cost of higher cutting force. (paper)

Vapor-melt Ratio in Laser Fine Cutting of Slot Arrays

International Nuclear Information System (INIS)

Wang Xuyue; Meng Qingxuan; Kang Renke; Xu Wenji; Guo Dongming; Wang Lianji

2011-01-01

In order to improve cut quality for slot arrays, a new method of laser fine cutting under the consideration of the ratio of vapor to melt is presented. Laser cutting of 6063 aluminum alloy sheet, 0.5 mm in thickness, was carried out on a JK701H Nd:YAG pulse laser cutting system. The effects of vapor-melt ratio on kerf width, surface roughness and recast layer were studied which relate cutting qualities. Observation on the cut samples with different vapor-melt ratios (0.687, 1.574, 3.601 varied with laser power increasing, and 1.535, 3.601, 7.661 with decreasing of beam cutting speed) shows that high vapor-melt ratio improves laser cut quality clearly. Kerf width 0.2 mm of smooth area on kerf top area and thickness 2.03 μm of recast layer are obtained. No dross was found on the kerf bottom and the percentage of the smooth area is up to 40% out of whole kerf side. The research on vapor-melt ratio provides a deeper understanding of laser cutting and improves laser cut quality effectively.

Cutting technique for reactor internals by laser beam

International Nuclear Information System (INIS)

Matsumoto, O.; Sugihara, M.; Matsuda, K.; Miya, K.

1990-01-01

At present in Japan the verification tests on the commercial nuclear power reactor decommissioning technology are being conducted as the project of The Ministry of International Trade and Industry by Nuclear Power Engineering Test Center. This paper summarizes the interim results of the verification test for the reactor core internals decommissioning technology, which is being conducted from 1986 as a theme of the above project. All core internals to be studied here are made of stainless steel, and the maximum wall thickness is about 500mm (the maximum one to be cut is about 300mm) for the PWR's, and about 100mm for the BWR's. Though the plasma cutting, arc saw cutting method, etc. have been studied u p to now as the cutting technology for decommissioning these core internals, the authors are carrying out the development and verification test of the cutting technology with the laser beam, which is expected to increase its power in future and can be applied to various materials

Burrowing as a novel voluntary strength training method for mice: A comparison of various voluntary strength or resistance exercise methods.

Science.gov (United States)

Roemers, P; Mazzola, P N; De Deyn, P P; Bossers, W J; van Heuvelen, M J G; van der Zee, E A

2018-04-15

Voluntary strength training methods for rodents are necessary to investigate the effects of strength training on cognition and the brain. However, few voluntary methods are available. The current study tested functional and muscular effects of two novel voluntary strength training methods, burrowing (digging a substrate out of a tube) and unloaded tower climbing, in male C57Bl6 mice. To compare these two novel methods with existing exercise methods, resistance running and (non-resistance) running were included. Motor coordination, grip strength and muscle fatigue were measured at baseline, halfway through and near the end of a fourteen week exercise intervention. Endurance was measured by an incremental treadmill test after twelve weeks. Both burrowing and resistance running improved forelimb grip strength as compared to controls. Running and resistance running increased endurance in the treadmill test and improved motor skills as measured by the balance beam test. Post-mortem tissue analyses revealed that running and resistance running induced Soleus muscle hypertrophy and reduced epididymal fat mass. Tower climbing elicited no functional or muscular changes. As a voluntary strength exercise method, burrowing avoids the confounding effects of stress and positive reinforcers elicited in forced strength exercise methods. Compared to voluntary resistance running, burrowing likely reduces the contribution of aerobic exercise components. Burrowing qualifies as a suitable voluntary strength training method in mice. Furthermore, resistance running shares features of strength training and endurance (aerobic) exercise and should be considered a multi-modal aerobic-strength exercise method in mice. Copyright © 2017 Elsevier B.V. All rights reserved.

Standard test method for galling resistance of material couples

CERN Document Server

American Society for Testing and Materials. Philadelphia

2008-01-01

1.1 This test method covers a laboratory test that ranks the galling resistance of material couples using a quantitative measure. Bare metals, alloys, nonmetallic materials, coatings, and surface modified materials may be evaluated by this test method. 1.2 This test method is not designed for evaluating the galling resistance of material couples sliding under lubricated conditions, because galling usually will not occur under lubricated sliding conditions using this test method. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

A Novel Parabolic Trough Concentrating Solar Heating for Cut Tobacco Drying System

Directory of Open Access Journals (Sweden)

Jiang Tao Liu

2014-01-01

Full Text Available A novel parabolic trough concentrating solar heating for cut tobacco drying system was established. The opening width effect of V type metal cavity absorber was investigated. A cut tobacco drying mathematical model calculated by fourth-order Runge-Kutta numerical solution method was used to simulate the cut tobacco drying process. And finally the orthogonal test method was used to optimize the parameters of cut tobacco drying process. The result shows that the heating rate, acquisition factor, and collector system efficiency increase with increasing the opening width of the absorber. The simulation results are in good agreement with experimental data for cut tobacco drying process. The relative errors between simulated and experimental values are less than 8%, indicating that this mathematical model is accurate for the cut tobacco airflow drying process. The optimum preparation conditions are an inlet airflow velocity of 15 m/s, an initial cut tobacco moisture content of 26%, and an inlet airflow temperature of 200°C. The thermal efficiency of the dryer and the final cut tobacco moisture content are 66.32% and 14.15%, respectively. The result shows that this parabolic trough concentrating solar heating will be one of the heat recourse candidates for cut tobacco drying system.

Research on NC laser combined cutting optimization model of sheet metal parts

Science.gov (United States)

Wu, Z. Y.; Zhang, Y. L.; Li, L.; Wu, L. H.; Liu, N. B.

2017-09-01

The optimization problem for NC laser combined cutting of sheet metal parts was taken as the research object in this paper. The problem included two contents: combined packing optimization and combined cutting path optimization. In the problem of combined packing optimization, the method of “genetic algorithm + gravity center NFP + geometric transformation” was used to optimize the packing of sheet metal parts. In the problem of combined cutting path optimization, the mathematical model of cutting path optimization was established based on the parts cutting constraint rules of internal contour priority and cross cutting. The model played an important role in the optimization calculation of NC laser combined cutting.

Standard test method for measurement of soil resistivity using the two-electrode soil box method

CERN Document Server

American Society for Testing and Materials. Philadelphia

2005-01-01

1.1 This test method covers the equipment and a procedure for the measurement of soil resistivity, for samples removed from the ground, for use in the control of corrosion of buried structures. 1.2 Procedures allow for this test method to be used n the field or in the laboratory. 1.3 The test method procedures are for the resistivity measurement of soil samples in the saturated condition and in the as-received condition. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Soil resistivity values are reported in ohm-centimeter. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Overview of PVD wear resistant coatings

International Nuclear Information System (INIS)

Teeter, F.J.

1999-01-01

The combined functionality of wear-resistant and low-friction multilayer coatings has widened application possibilities for a new generation of coated tools. For the first time tool wear mechanisms are comprehensively addressed both at the cutting edge and contact areas away from the edge where chip evacuation is facilitated. Since its recent market introduction a combined TiA1N and WC/C PVD coating has been proven to increase cutting performance in various metal cutting operations, notably drilling and tapping of steels and aluminum alloys. Significant improvements have been obtained under dry as well as with coolant conditions. The results of laboratory metal cutting tests and field trials to date will be described. Correlations between chip formation / wear mechanisms and coating properties are given to explain the effectiveness of this coating. (author)

Investigation of Micro Square Structure Fabrication by Applying Textured Cutting Tool in WEDM

Directory of Open Access Journals (Sweden)

Jianguo Zhang

2015-09-01

Full Text Available This paper studies micro structure fabrication by means of a textured tool cutting edge, which is manufactured by applying the wire cut electrical discharge machining (WEDM. Machining performance of the square structure fabrication on the tool cutting edge is investigated in the WEDM process, and the machining accuracy is explored in experimental analyses. In this proposed method, undesired overcut comes from the discharge between the processing debris and the side wall of the target structure. Furthermore, by applying the textured cutting tool, the target square structure is directly fabricated on the alumina workpiece with just a simple turning process, which verifies the feasibility of the proposed tool cutting edge textured method by applying the WEDM. This technology is expected to become a potential method for the mass production of micro structure surfaces in the future.

Multi-objective optimization of surface roughness, cutting forces, productivity and Power consumption when turning of Inconel 718

Directory of Open Access Journals (Sweden)

Hamid Tebassi

2016-01-01

Full Text Available Nickel based super alloys are excellent for several applications and mainly in structural components submitted to high temperatures owing to their high strength to weight ratio, good corrosion resistance and metallurgical stability such as in cases of jet engine and gas turbine components. The current work presents the experimental investigations of the cutting parameters effects (cutting speed, depth of cut and feed rate on the surface roughness, cutting force components, productivity and power consumption during dry conditions in straight turning using coated carbide tool. The mathematical models for output parameters have been developed using Box-Behnken design with 15 runs and Box-Cox transformation was used for improving normality. The results of the analysis have shown that the surface finish was statistically sensitive to the feed rate and cutting speed with the contribution of 43.58% and 23.85% respectively, while depth of cut had the greatest effect on the evolution of cutting force components with the contribution of 79.87% for feed force, 66.92% for radial force and 66.26% for tangential force. Multi-objective optimization procedure allowed minimizing roughness Ra, cutting forces and power consumption and maximizing material removal rate using desirability approach.

Comparative Analysis of Three Methods for Determination of Imipenem Resistance in Pseudomonas aeruginosa

Directory of Open Access Journals (Sweden)

Tanaz Zabihi

2016-02-01

Full Text Available "> Background: These days, the antibiotic resistance of Pseudomonas aeruginosa isolates toimipenem has significantly increased. Therefore the study of resistance to imipenem in thisorganism to imipenem in determining the appropriate treatment is crucial and necessary. The goalof this study is to compare three phenotypic methods of E-test, disk diffusion and micro brothdilution in the study of resistance to imipenem in clinical isolates of P. aeruginosa.Methods: Within a 6-month interval, 120 clinical specimens were collected and evaluated. Allisolates were identified as P. aeruginosa by standard biochemical tests and amplification of 16SrRNA gene. Three phenotypic methods of E-test, disk diffusion, and micro broth dilution wereused to determine imipenem resistance in P. aeruginosa isolates.Results: Of the 96 P. aeruginosa isolates studied for their resistance to imipenem by the use ofE-test, disk diffusion and micro broth dilution methods, 38.5% of the strains in micro broth dilutionmethod and 33.3% in the two methods of E-test and disk diffusion were resistant to imipenem. Therate of sensitivity and specificity of disk diffusion and E-test methods were 100%, 90.1%, and theywere 100% and 83.1% for micro broth dilution, respectively.Conclusions: With regard to the results obtained from the comparison of the three methods100% agreement were observed among the antimicrobial susceptibility results obtained by the Etest and disk diffusion methods (P ≥ 0.05. Therefore, the use of disk diffusion method can bean appropriate replacement for E-test method with regard to its being easy and cost-effective.

Novel composite cBN-TiN coating deposition method: structure and performance in metal cutting

International Nuclear Information System (INIS)

Russell, W.C.; Malshe, A.P.; Yedave, S.N.; Brown, W.D.

2001-01-01

Cubic boron nitride coatings are under development for a variety of applications but stabilization of the pure cBN form and adhesion of films deposited by PVD and ion-based methods has been difficult. An alternative method for depositing a composite cBN-TiN film has been developed for wear related applications. The coating is deposited in a two-stage process utilizing ESC (electrostatic spray coating) and CVI (chemical vapor infiltration). Fully dense films of cBN particles evenly dispersed in a continuous TiN matrix have been developed. Testing in metal cutting has shown an increase in tool life (turning - 4340 steel) of three to seven times, depending of machining parameters, in comparison with CVD deposited TiN films. (author)

Wet cutting

Energy Technology Data Exchange (ETDEWEB)

Hole, B. [IMC Technical Services (United Kingdom)

1999-08-01

Continuous miners create dust and methane problems in underground coal mining. Control has usually been achieved using ventilation techniques as experiments with water based suppression have led to flooding and electrical problems. Recent experience in the US has led to renewed interest in wet head systems. This paper describes tests of the Hydraphase system by IMC Technologies. Ventilation around the cutting zone, quenching of hot ignition sources, dust suppression, the surface trial gallery tests, the performance of the cutting bed, and flow of air and methane around the cutting head are reviewed. 1 ref., 2 figs., 2 photos.

TransCut: interactive rendering of translucent cutouts.

Science.gov (United States)

Li, Dongping; Sun, Xin; Ren, Zhong; Lin, Stephen; Tong, Yiying; Guo, Baining; Zhou, Kun

2013-03-01

We present TransCut, a technique for interactive rendering of translucent objects undergoing fracturing and cutting operations. As the object is fractured or cut open, the user can directly examine and intuitively understand the complex translucent interior, as well as edit material properties through painting on cross sections and recombining the broken pieces—all with immediate and realistic visual feedback. This new mode of interaction with translucent volumes is made possible with two technical contributions. The first is a novel solver for the diffusion equation (DE) over a tetrahedral mesh that produces high-quality results comparable to the state-of-art finite element method (FEM) of Arbree et al. but at substantially higher speeds. This accuracy and efficiency is obtained by computing the discrete divergences of the diffusion equation and constructing the DE matrix using analytic formulas derived for linear finite elements. The second contribution is a multiresolution algorithm to significantly accelerate our DE solver while adapting to the frequent changes in topological structure of dynamic objects. The entire multiresolution DE solver is highly parallel and easily implemented on the GPU. We believe TransCut provides a novel visual effect for heterogeneous translucent objects undergoing fracturing and cutting operations.

Fundamentals of cutting.

Science.gov (United States)

Williams, J G; Patel, Y

2016-06-06

The process of cutting is analysed in fracture mechanics terms with a view to quantifying the various parameters involved. The model used is that of orthogonal cutting with a wedge removing a layer of material or chip. The behaviour of the chip is governed by its thickness and for large radii of curvature the chip is elastic and smooth cutting occurs. For smaller thicknesses, there is a transition, first to plastic bending and then to plastic shear for small thicknesses and smooth chips are formed. The governing parameters are tool geometry, which is principally the wedge angle, and the material properties of elastic modulus, yield stress and fracture toughness. Friction can also be important. It is demonstrated that the cutting process may be quantified via these parameters, which could be useful in the study of cutting in biology.

Critical element development of standard components for pipe welding/cutting by CO{sub 2} laser

Energy Technology Data Exchange (ETDEWEB)

Oka, Kiyoshi; Kakudate, Satoshi; Nakahira, Masataka [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment] [and others

1994-11-01

In D-T burning reactors such as International Thermonuclear Experimental Reactor(ITER), an internal access is inevitable for welding/cutting of cooling pipes of in-vessel components, because of spatial constraint due to a narrow port opening space. An internal-access pipe welding/cutting equipment is being developed in JAERI. Internal access is to approach through inside a pipe to a welding/cutting position, to use 10kW CO{sub 2} laser beam, and to be applicable to both welding and cutting with using a same processing head. A welding/cutting processing head with 10kW CO{sub 2} laser beam has been fabricated and the basic feasibility has been successfully demonstrated for studies of the internal-access pipe welding/cutting concept using 100-A stainless steel pipe with a thickness of 6.3mm. In this study, the optimum focal point of laser beam, laser power and traveling speed of the head have been investigated together with an adjusting mechanism of a relative distance between the head and the pipe wall. In addition, the radiation resistance of critical elements such as optical lens has been investigated. (author).

Force Relations and Dynamics of Cutting Knife in a Vertical Disc Mobile Wood Chipper

Directory of Open Access Journals (Sweden)

Segun R. BELLO

2011-06-01

Full Text Available The force relations and dynamics of cutting knife in a vertical disc wood chipper were investigated. The tool geometry determined include: rake angle (20 deg C; Shear angle, (fi= 52.15 deg C; the mean frictional angle, (t = 5.71 deg C. The analysis and comparison of the cutting forces has shown that the chips separated from the wood are being formed by off cutting, since normal applied force N is compressive in nature, the magnitude of the forces used by the knife on the wood is expected to increase as the cutting edge of the knife goes deeper into the wood until the value of the resisting force acting against the cut wood Ff is reached and exceeded. The evaluated forces acting on the knife and the chip are: F = 3.63Nmm^-1; N = 34.7 Nmm^-1; Fs= 27.45Nmm^-1; Fn =31.92 Nmm^-1; Ft = -8.46Nmm^-1; Fc = 33.85Nmm^-1. The resultant force acting on the tool face, Pr = 34.89Nmm^-1. The specific cutting pressure, Pc and cutting force needed to cut the timber, Fc, are 1.79 × 10^6 N/m2 and 644.84N respectively. The energy consumed in removing a unit volume of material is 69.96kJ/mm^-3 and the maximum power developed in cutting the chip is 3591.77W (4.82hp. The chipper efficiency (86.6% was evaluated by the highest percentage of accepted chip sizes.

Development of the spent fuel rod cutting device using the blade cutters

International Nuclear Information System (INIS)

Jung, Jae Hoo; Yoon, Ji Sup; Hong, Dong Hee; Kim, Young Hwan; Park, Gee Yong; Kim, Do Woo

2000-11-01

A spent fuel rod cutting device is to cut a spent nuclear fuel rod to optimal size for consequent decladding operation. In this paper, various properties of fuel rod, such as a dimension and material of zircaloy tubes and fuel pellets, are investigated. Also, commercially available cutting method and tools is investigated in terms of its performance. As a result, the blade cutter is selected for the design. In order to fabricate the durable blade cutter, various materials are analyzed in terms of material properties, cutter shape, and heat treatment method, etc. Also, the durability of this tool is tested by cutting the SUS tubes and zircaloy tubes. In the device design, the remote maintainability is considered so that the modularized design is accomplished. Also, the other factors considered in the design are the round shape sustainability at the cut surface, the amount of debris generation, and the fire risk, etc. Considering these design consideration, the spent fuel rod cutting device is fabricated and tested

Shroud cutting techniques and collection systems for secondary radioactivity release

International Nuclear Information System (INIS)

Yokoi, H.; Watanabe, A.; Uetake, N.; Shimura, T.; Omote, T.; Adachi, H.; Murakami, S.; Kobayashi, H.; Gotoh, M.

2001-01-01

Replacement of in-core shroud has been conducted as part of the preventive maintenance program in Tsuruga-1. The EDM (electric discharged machining) and plasma cutting methods were applied to in-core shroud cutting and secondary cutting in the DSP (dryer/separator pool), respectively. The cutting systems were improved in order to decrease radioactive secondary products. 1) Fundamental EDM cutting tests: fundamental EDM cutting tests were carried out in order to study secondary products. It could be presumed that volatile Co-carbonyl compound was generated by using a carbon electrode. The Ag/W electrode was effective as EDM electrode for in-core shroud cutting to prevent generation of Co-carbonyl compound and to decrease the total amount of secondary products. 2) In-core shroud cutting in RPV (reactor pressure vessel): EDM cutting system with the Ag/W electrode and collection system could keep a good environment during in-core shroud cutting in Tsuruga-1. Activity concentration was lower value than limitation of mask charge level, 4E-6 Bq/cm 3 , even near the water surface. 3) Secondary plasma cutting in DSP: the secondary cutting work was successful in the point of reduction of working period and radiation exposure. The amount of radiation exposure was reduced to 60% of the planned value, because of adequate decontamination of the working environment and reduction of number of torch maintenance tasks by improvements of the underwater cutting device

Device for cutting protrusions

Science.gov (United States)

Bzorgi, Fariborz M [Knoxville, TN

2011-07-05

An apparatus for clipping a protrusion of material is provided. The protrusion may, for example, be a bolt head, a nut, a rivet, a weld bead, or a temporary assembly alignment tab protruding from a substrate surface of assembled components. The apparatus typically includes a cleaver having a cleaving edge and a cutting blade having a cutting edge. Generally, a mounting structure configured to confine the cleaver and the cutting blade and permit a range of relative movement between the cleaving edge and the cutting edge is provided. Also typically included is a power device coupled to the cutting blade. The power device is configured to move the cutting edge toward the cleaving edge. In some embodiments the power device is activated by a momentary switch. A retraction device is also generally provided, where the retraction device is configured to move the cutting edge away from the cleaving edge.

Experimental research on the durability cutting tools for cutting-off steel profiles

Directory of Open Access Journals (Sweden)

Cristea Alexandru

2017-01-01

Full Text Available The production lines used for manufacturing U-shaped profiles are very complex and they must have high productivity. One of the most important stages of the fabrication process is the cutting-off. This paper presents the experimental research and analysis of the durability of the cutting tools used for cutting-off U-shaped metal steel profiles. The results of this work can be used to predict the durability of the cutting tools.

Benchmarking of methods for identification of antimicrobial resistance genes in bacterial whole genome data

DEFF Research Database (Denmark)

Clausen, Philip T. L. C.; Zankari, Ea; Aarestrup, Frank Møller

2016-01-01

to two different methods in current use for identification of antibiotic resistance genes in bacterial WGS data. A novel method, KmerResistance, which examines the co-occurrence of k-mers between the WGS data and a database of resistance genes, was developed. The performance of this method was compared...... with two previously described methods; ResFinder and SRST2, which use an assembly/BLAST method and BWA, respectively, using two datasets with a total of 339 isolates, covering five species, originating from the Oxford University Hospitals NHS Trust and Danish pig farms. The predicted resistance...... was compared with the observed phenotypes for all isolates. To challenge further the sensitivity of the in silico methods, the datasets were also down-sampled to 1% of the reads and reanalysed. The best results were obtained by identification of resistance genes by mapping directly against the raw reads...

A single method for recovery and concentration of enteric viruses and bacteria from fresh-cut vegetables.

Science.gov (United States)

Sánchez, G; Elizaquível, P; Aznar, R

2012-01-03

Fresh-cut vegetables are prone to be contaminated with foodborne pathogens during growth, harvest, transport and further processing and handling. As most of these products are generally eaten raw or mildly treated, there is an increase in the number of outbreaks caused by viruses and bacteria associated with fresh vegetables. Foodborne pathogens are usually present at very low levels and have to be concentrated (i.e. viruses) or enriched (i.e. bacteria) to enhance their detection. With this aim, a rapid concentration method has been developed for the simultaneous recovery of hepatitis A virus (HAV), norovirus (NV), murine norovirus (MNV) as a surrogate for NV, Escherichia coli O157:H7, Listeria monocytogenes and Salmonella enterica. Initial experiments focused on evaluating the elution conditions suitable for virus release from vegetables. Finally, elution with buffered peptone water (BPW), using a Pulsifier, and concentration by polyethylene glycol (PEG) precipitation were the methods selected for the elution and concentration of both, enteric viruses and bacteria, from three different types of fresh-cut vegetables by quantitative PCR (qPCR) using specific primers. The average recoveries from inoculated parsley, spinach and salad, were ca. 9.2%, 43.5%, and 20.7% for NV, MNV, and HAV, respectively. Detection limits were 132 RT-PCR units (PCRU), 1.5 50% tissue culture infectious dose (TCID₅₀), and 6.6 TCID₅₀ for NV, MNV, and HAV, respectively. This protocol resulted in average recoveries of 57.4%, 64.5% and 64.6% in three vegetables for E. coli O157:H7, L. monocytogenes and Salmonella with corresponding detection limits of 10³, 10² and 10³ CFU/g, respectively. Based on these results, it can be concluded that the procedure herein is suitable to recover, detect and quantify enteric viruses and foodborne pathogenic bacteria within 5 h and can be applied for the simultaneous detection of both types of foodborne pathogens in fresh-cut vegetables. Copyright �

Phonon cross-plane transport and thermal boundary resistance: effect of heat source size and thermal boundary resistance on phonon characteristics

Science.gov (United States)

Ali, H.; Yilbas, B. S.

2016-09-01

Phonon cross-plane transport across silicon and diamond thin films pair is considered, and thermal boundary resistance across the films pair interface is examined incorporating the cut-off mismatch and diffusive mismatch models. In the cut-off mismatch model, phonon frequency mismatch for each acoustic branch is incorporated across the interface of the silicon and diamond films pair in line with the dispersion relations of both films. The frequency-dependent and transient solution of the Boltzmann transport equation is presented, and the equilibrium phonon intensity ratios at the silicon and diamond film edges are predicted across the interface for each phonon acoustic branch. Temperature disturbance across the edges of the films pair is incorporated to assess the phonon transport characteristics due to cut-off and diffusive mismatch models across the interface. The effect of heat source size, which is allocated at high-temperature (301 K) edge of the silicon film, on the phonon transport characteristics at the films pair interface is also investigated. It is found that cut-off mismatch model predicts higher values of the thermal boundary resistance across the films pair interface as compared to that of the diffusive mismatch model. The ratio of equilibrium phonon intensity due to the cut-off mismatch over the diffusive mismatch models remains >1 at the silicon edge, while it becomes <1 at the diamond edge for all acoustic branches.

Study of Cutting Edge Temperature and Cutting Force of End Mill Tool in High Speed Machining

Directory of Open Access Journals (Sweden)

Kiprawi Mohammad Ashaari

2017-01-01

Full Text Available A wear of cutting tools during machining process is unavoidable due to the presence of frictional forces during removing process of unwanted material of workpiece. It is unavoidable but can be controlled at slower rate if the cutting speed is fixed at certain point in order to achieve optimum cutting conditions. The wear of cutting tools is closely related with the thermal deformations that occurred between the frictional contact point of cutting edge of cutting tool and workpiece. This research paper is focused on determinations of relationship among cutting temperature, cutting speed, cutting forces and radial depth of cutting parameters. The cutting temperature is determined by using the Indium Arsenide (InAs and Indium Antimonide (InSb photocells to measure infrared radiation that are emitted from cutting tools and cutting forces is determined by using dynamometer. The high speed machining process is done by end milling the outer surface of carbon steel. The signal from the photocell is digitally visualized in the digital oscilloscope. Based on the results, the cutting temperature increased as the radial depth and cutting speed increased. The cutting forces increased when radial depth increased but decreased when cutting speed is increased. The setup for calibration and discussion of the experiment will be explained in this paper.

Cutting Edge Localisation in an Edge Profile Milling Head

NARCIS (Netherlands)

Fernandez Robles, Laura; Azzopardi, George; Alegre, Enrique; Petkov, Nicolai

2015-01-01

Wear evaluation of cutting tools is a key issue for prolonging their lifetime and ensuring high quality of products. In this paper, we present a method for the effective localisation of cutting edges of inserts in digital images of an edge profile milling head. We introduce a new image data set of

Laser cutting of concretes with various ballasts

International Nuclear Information System (INIS)

Hamasaki, Masanobu; Katsumura, Munehide; Utsumi, Hiroaki

1985-01-01

The biological shield concrete and the radiation shield concrete which construct a part of the atomic reactor must be demolished with the decommissioning of the atomic reactor plants. In a case, the demolition using a laser is expected as one of excellent method for the decommissioning of these radioactive concretes. The fundamental cuttings of a mortar, the concretes with andesite, lime stone and gray wacke as ballast and a concrete reinforced with mild steel rods were therefore carried out using a 5 kW output CO 2 laser. As the results of experiment, it was cleared that cutting results varied with ballasts, 100 mm thick reinforced concrete could be cut, safety was high because few dross and few fume were produced. (author)

The Cutting Process, Chips and Cutting Forces in Machining CFRP

DEFF Research Database (Denmark)

Koplev, A.; Lystrup, Aage; Vorm, T.

1983-01-01

The cutting of unidirectional CFRP, perpendicular as well as parallel to the fibre orientation, is examined. Shaping experiments, ‘quick-stop’ experiments, and a new chip preparation technique are used for the investigation. The formation of the chips, and the quality of the machined surface...... is discussed. The cutting forces parallel and perpendicular to the cutting direction are measured for various parameters, and the results correlated to the formation of chips and the wear of the tool....

Indirect questioning method reveals hidden support for female genital cutting in South Central Ethiopia.

Science.gov (United States)

Gibson, Mhairi A; Gurmu, Eshetu; Cobo, Beatriz; Rueda, María M; Scott, Isabel M

2018-01-01

Female genital cutting (FGC) has major implications for women's physical, sexual and psychological health, and eliminating the practice is a key target for public health policy-makers. To date one of the main barriers to achieving this has been an inability to infer privately-held views on FGC within communities where it is prevalent. As a sensitive (and often illegal) topic, people are anticipated to hide their true support for the practice when questioned directly. Here we use an indirect questioning method (unmatched count technique) to identify hidden support for FGC in a rural South Central Ethiopian community where the practice is common, but thought to be in decline. Employing a socio-demographic household survey of 1620 Arsi Oromo adults, which incorporated both direct and indirect direct response (unmatched count) techniques we compare directly-stated versus privately-held views in support of FGC, and individual variation in responses by age, gender and education and target female (daughters versus daughters-in-law). Both genders express low support for FGC when questioned directly, while indirect methods reveal substantially higher acceptance (of cutting both daughters and daughters-in-law). Educated adults (those who have attended school) are privately more supportive of the practice than they are prepared to admit openly to an interviewer, indicating that education may heighten secrecy rather than decrease support for FGC. Older individuals hold the strongest views in favour of FGC (particularly educated older males), but they are also more inclined to conceal their support for FGC when questioned directly. As these elders represent the most influential members of society, their hidden support for FGC may constitute a pivotal barrier to eliminating the practice in this community. Our results demonstrate the great potential for indirect questioning methods to advance knowledge and inform policy on culturally-sensitive topics like FGC; providing more

A METHOD FOR CREATING STRUCTURES OR DEVICES USING AN ORGANIC ICE RESIST

DEFF Research Database (Denmark)

2017-01-01

The invention relates to a method for creating an organic resist on a surface of a cooled substrate, the method comprising the steps of condensing a vapour into a solid film on the surface of the cooled substrate; patterning at least part of the solid film by exposing selected portions of said...... solid film to at least one electron beam thereby creating the organic resist on 5 the surface of the cooled substrate in accordance with a predetermined pattern; wherein the created organic resist remains essentially intact at ambient conditions; and using the created organic resist as a mask...... for creating semiconductor structures and/or semiconductor devices....

Electrical Resistivity Measurement of Petroleum Coke Powder by Means of Four-Probe Method

Science.gov (United States)

Rouget, G.; Majidi, B.; Picard, D.; Gauvin, G.; Ziegler, D.; Mashreghi, J.; Alamdari, H.

2017-10-01

Carbon anodes used in Hall-Héroult electrolysis cells are involved in both electrical and chemical processes of the cell. Electrical resistivity of anodes depends on electrical properties of its constituents, of which carbon coke aggregates are the most prevalent. Electrical resistivity of coke aggregates is usually characterized according to the ISO 10143 standardized test method, which consists of measuring the voltage drop in the bed of particles between two electrically conducing plungers through which the current is also applied. Estimation of the electrical resistivity of coke particles from the resistivity of particle bed is a challenging task and needs consideration of the contribution of the interparticle void fraction and the particle/particle contact resistances. In this work, the bed resistivity was normalized by subtracting the interparticle void fraction. Then, the contact size was obtained from discrete element method simulation and the contact resistance was calculated using Holm's theory. Finally, the resistivity of the coke particles was obtained from the bed resistivity.

Experimental Investigation on Cutting Characteristics in Nanometric Plunge-Cutting of BK7 and Fused Silica Glasses.

Science.gov (United States)

An, Qinglong; Ming, Weiwei; Chen, Ming

2015-03-27

Ductile cutting are most widely used in fabricating high-quality optical glass components to achieve crack-free surfaces. For ultra-precision machining of brittle glass materials, critical undeformed chip thickness (CUCT) commonly plays a pivotal role in determining the transition point from ductile cutting to brittle cutting. In this research, cutting characteristics in nanometric cutting of BK7 and fused silica glasses, including machined surface morphology, surface roughness, cutting force and specific cutting energy, were investigated with nanometric plunge-cutting experiments. The same cutting speed of 300 mm/min was used in the experiments with single-crystal diamond tool. CUCT was determined according to the mentioned cutting characteristics. The results revealed that 320 nm was found as the CUCT in BK7 cutting and 50 nm was determined as the size effect of undeformed chip thickness. A high-quality machined surface could be obtained with the undeformed chip thickness between 50 and 320 nm at ductile cutting stage. Moreover, no CUCT was identified in fused silica cutting with the current cutting conditions, and brittle-fracture mechanism was confirmed as the predominant chip-separation mode throughout the nanometric cutting operation.

Analysis of changes in paper cutting forces during the cutting cycle in single-knife guillotine

OpenAIRE

Rusin, Agnieszka; Petriaszwili, Georgij

2013-01-01

Paper presents the results of changes in the three components of cutting forces of paper stacks cutting during the cutting cycle in single-knife guillotine. The changes of the three components of cutting force at different stages of cutting cycle were analyzed.

Rooting Platanus (Platanus acerifolia (Aiton Willd. cuttings in Marechal Cândido Rondon - PR, Brazil: Influence of lesions at cutting bases and depth of planting

Directory of Open Access Journals (Sweden)

Danimar Dalla Rosa

2018-01-01

Full Text Available Platanus, an arboreal and deciduous plant, is widely adapted and can be used for several purposes. Despite producing viable seeds, production of platanus seedlings usually occurs through vegetative propagation; cuttings are the best and most efficient source for obtaining seedlings. Although cuttings offer a practical and easy method to obtain seedlings in different vegetable species, they are influenced by several factors, both external and internal. The present study aimed to analyze the behavior of plantain cuttings planted in sand subjected to damage or no damage at the cuttings base, and planted at depths of 20 and 40 cm. Experiment was carried out at the experimental station of horticulture and protected cultivation of UNIOESTE-Brazil, in a randomized 2×2 factorial design, which comprises both, planted at 20 cm and 40 cm depths, with 5 replicates and 5 cuttings per replicate. After 170 days of incubation, injured and non- injured cuttings, were evaluated for rooting percentage and cuttings sprouted, length of roots and medium length of stems, stem diameter, number of leaves per stem, and dry mass of roots and shoots. No significant differences were observed in cutting injury. All variables analyzed presented higher values when cuttings were planted at 20 cm depth. Results indicate that planting of platanus cuttings at 20 cm depth leads to better rooting rates and vegetative development.

EPICORMIC SHOOTS INDUCTION AND ROOTING CUTTINGS OF Calophyllum brasiliense

Directory of Open Access Journals (Sweden)

Dagma Kratz

2016-12-01

Full Text Available Calophyllum brasiliense is present in a wide natural distribution range in Brazil and its monopodial growth, with a rectilinear stem and a moderately dense timber has attracted the attention from the logging industry in recent decades. In the meantime, the lack of efficient rescue and vegetative propagation methods of adult plants has been a narrowing condition for the selection of superior genotypes in breeding programs of the species. Therefore, we evaluate epicormic shoots induction methods and the rooting cuttings of 14 year-old Calophyllum brasiliense trees. From this scope, three methods of epicormic shoots induction were evaluated: coppicing, girdling and partial girdling. We evaluate the number of produced sprouts and the percentage of sprouted trees at 06, 12 and 15 months’ after the experiment installation. Results have indicated the feasibility of Calophyllum brasiliense vegetative rescue by cuttings method using epicormic shoots induced by coppicing and girdling. In contrast, partial girdling was not effective in epicormic shoots emission. Concerning adventitious roots, the sprouting technique had no influence in the rooting of cuttings, showing variation among the different stock plants.

Using arc voltage to locate the anode attachment in plasma arc cutting

International Nuclear Information System (INIS)

Osterhouse, D J; Heberlein, J V R; Lindsay, J W

2013-01-01

Plasma arc cutting is a widely used industrial process in which an electric arc in the form of a high velocity plasma jet is used to melt and blow away metal. The arc attaches inside the resulting cut slot, or kerf, where it both provides a large heat flux and determines the flow dynamics of the plasma. Knowledge of the position of the arc attachment is essential for understanding the phenomena present at the work piece. This work presents a new method of measuring the location of the arc attachment in which the arc voltage is measured during the cutting of a range of work piece thicknesses. The attachment location is then interpreted from the voltages. To support the validity of this method, the kerf shape, dross particle size and dross adhesion to the work piece are also observed. While these do not conclusively give an attachment location, they show patterns which are consistent with the attachment location found from the voltage measurements. The method is demonstrated on the cutting of mild steel, where the arc attachment is found to be stationary in the upper portion of the cut slot and in reasonable agreement with existing published findings. For a process optimized for the cutting of 12.7 mm mild steel, the attachment is found at a depth of 1.5–3.4 mm. For a slower process optimized for the cutting of 25.4 mm mild steel, the attachment is found at a depth of 3.4–4.8 mm, which enhances heat transfer further down in the kerf, allowing cutting of the thicker work piece. The use of arc voltage to locate the position of the arc attachment is unique when compared with existing methods because it is entirely independent of the heat distribution and visualization techniques. (paper)

Formation of Quenching Structures in the Steel 35 by Deform Cutting

Directory of Open Access Journals (Sweden)

A. G. Degtyareva

2014-01-01

Full Text Available In industry different methods of surface hardening are widely used to increase reliability and durability of friction unit parts. Among these methods are areas of focus based on deformcutting technology (DC i.e. method of chip-free mechanical treatment.It is shown that DC method allows us to produce through- or partial-hardening surface layers of a large thickness (0,4…1.5mm on steel with no additional heat sources. The standard metal-cutting equipment and common tools are used for deform-cutting process.The significant heat generation in the deform-cutting zone and mechanical effect from the tool allow us to heat undercut layers to the phase transformation point to have the hardening structure as a result of heat removal to the cold balk. The hardening structure formation occurs at significant heating and cooling rate (106C/c with large degrees and rates of strain.The deform-cutting modes and working face tool grinding determine the type and properties of the hardening structure. To produce the hardening structure would require the heat transfer and force action augmentation while treatment.These researches deal with through- and partial surface hardening samples produced by turning steel 35 shafts. While through hardening the phase transformation carry among the whole thickness of the undercut layer; while partial hardening the hardening interlayer formed on the side of the cutting tool contact.The depth of hardening zone of samples with through hardening layers is 0,5 mm; the depth of hardening zone of partial hardening samples is 0,8 mm. Micro-hardness of the through hardening layers is 653 HV0,1 and 485 HV0,1 for the partial hardening layers. The metallographic analysis shows that the hardening zone formed while deform cutting has disperse structure; there are ferrite ghosts in it.The tempering at temperatures of 200 – 700C showed that the micro-hardness of the hardening structures formed while deform cutting is larger than the micro

Study of PVD AlCrN Coating for Reducing Carbide Cutting Tool Deterioration in the Machining of Titanium Alloys.

Science.gov (United States)

Cadena, Natalia L; Cue-Sampedro, Rodrigo; Siller, Héctor R; Arizmendi-Morquecho, Ana M; Rivera-Solorio, Carlos I; Di-Nardo, Santiago

2013-05-24

The manufacture of medical and aerospace components made of titanium alloys and other difficult-to-cut materials requires the parallel development of high performance cutting tools coated with materials capable of enhanced tribological and resistance properties. In this matter, a thin nanocomposite film made out of AlCrN (aluminum-chromium-nitride) was studied in this research, showing experimental work in the deposition process and its characterization. A heat-treated monolayer coating, competitive with other coatings in the machining of titanium alloys, was analyzed. Different analysis and characterizations were performed on the manufactured coating by scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM-EDXS), and X-ray diffraction (XRD). Furthermore, the mechanical behavior of the coating was evaluated through hardness test and tribology with pin-on-disk to quantify friction coefficient and wear rate. Finally, machinability tests using coated tungsten carbide cutting tools were executed in order to determine its performance through wear resistance, which is a key issue of cutting tools in high-end cutting at elevated temperatures. It was demonstrated that the specimen (with lower friction coefficient than previous research) is more efficient in machinability tests in Ti6Al4V alloys. Furthermore, the heat-treated monolayer coating presented better performance in comparison with a conventional monolayer of AlCrN coating.

Cutting and Self-Harm

Science.gov (United States)

... Your feelings Feeling sad Cutting and self-harm Cutting and self-harm Self-harm, sometimes called self- ... There are many types of self-injury, and cutting is one type that you may have heard ...

Development of Convenient Screening Method for Resistant Radish to Plasmodiophora brassicae

Directory of Open Access Journals (Sweden)

Su-Jung Jo

2011-08-01

Full Text Available To establish simple and reliable screening method for resistant radish to Plasmodiophora brassicae Woron. using soil-drenching inoculation, the development of clubroot on radish seedlings inoculated with P. brassicae GN-1 isolate according to several conditions such as inoculum concentration, plant growth stage and incubation period after inoculation was studied. To select resistant radish against clubroot, 10-day-old seedlings were inoculated with P. brassicae by drenching the roots with the spore suspension of the pathogen to give 1×10(9 spores/pot. The inoculated seedlings were incubated in a growth chamber at 20℃ for 3 days then cultivated in a greenhouse (20±5℃ for 6 weeks. Under the optimum conditions, 46 commercial cultivars of radish were tested for resistance to YC-1 (infecting 15 clubroot-resistant cultivars of Chinese cabbage and GN-1 (wild type isolates of P. brassicae. Among them, thirty-five cultivars showed resistance to both isolates and one cultivar represented susceptible response to the pathogens. On the other hand, the other cultivars showed different responses against the tested P. brassicae pathogens. The results suggest that this method is an efficient system for screening radish with resistance to clubroot.

Determination of the stresses and displacements in the cut off curtain body executed by the > method

International Nuclear Information System (INIS)

Snisarenko, V.I.; Mel'nikov, A.I.

1994-01-01

Construction of the cut-off-curtain (COC) is analyzed as a possible variant to reduce the rate of radioactive horizontal migration. Such constructions can be executed by the > method. The theoretical analysis of the stress-strained state of the carried out using the methods of the theory of elasticity and of the limit equilibrium of the strewing medium. Theoretical dependences are obtained and formulas for practical calculations of the COC-body stress-strained state in the depth intervals which are of practical interest are suggested. The dependences obtained may be used to calculate the consolidation parameters and filtration coefficients, to choose materials for the COC body, geometrical size and film elements included

Cutting techniques of reinforced concrete by wire sawing

International Nuclear Information System (INIS)

Miyao, Hidehiko; Komatsu, Junji; Kamiyama, Yoshinori; Yasoshima, Harunori; Kukino, Yoshinori; Yamamoto, Yuichi; Miyazaki, Takashi; Aritomi, Masanori

1995-01-01

The Research Association for Nuclear Facility Decommissioning (RANDEC) has been carrying out demonstration tests to improve current technologies for decommissioning. The conceptual dismantling system has been studied and basic cutting tests have been carried out by wire sawing. In terms of waste management and dismantling efficiency, the diamond wire saw cutting method has advantages for cutting radioactive concrete in large blocks. A conceptual design for a dismantling system for various concrete shieldings of nuclear facilities has been developed and diamond wire sawing has been designed and manufactured. The basic cutting tests by wire sawing have been carried out to obtain quantitative data, in addition to the conceptual design of a dismantling system for biological shielding of various power reactors (PWR, BWR, GCR) and cell walls of nuclear fuel cycle facilities. On the basis of the conceptual dismantling system and quantitative cutting performance data, wire sawing equipment has been manufactured for use in nuclear facilities. This study was performed on consignment for the Science and Technology Agency of Japan. (author)

The comparative studies of ADI versus Hadfield cast steel wear resistance

Directory of Open Access Journals (Sweden)

Mieczysław Kaczorowski

2011-04-01

Full Text Available The results of comparative studies of wear resistance of ADI versus high manganese Hadfield cast steel are presented. For evaluation ofwear resistance three type of ADI were chosen. Two of them were of moderate strength ADI with 800 and 1000MPa tensile strength whilethe third was 1400MPa tensile strength ADI. The specimens were cut from ADI test YII type casting poured and heat treated in Institute ofFoundry in Krakow. The pin on disc method was used for wear resistance experiment. The specimens had a shape of 40mm long rod withdiameter 6mm. The load and speed were 100N and 0,54m/s respectively. It was concluded that the wear resistance of ADI is comparablewith high manganese cast steel and in case of low tensile grade ADI and is even better for high strength ADI than Hadfield steel.

Effects of Notch Introduction on 3-Point Bending Cutting Characteristics of Frozen Fish

OpenAIRE

Hagura, Yoshio; Suzuki, Kanichi

2002-01-01

We have proposed a freeze cutting method in which a three point bending load is applied on a frozen fish body to cut in round slices. Lowering the three-point bending load can facilitate the freeze cutting processing. Based on the idea that a notch in the fish body may lower the cutting load, the effect of introducing a notch was examined with respect to cutting stress and smoothness of cut surface in model fish meat and in saury. It was found that the introduced notch effectively lowered the...

On Permuting Cut with Contraction

OpenAIRE

Borisavljevic, Mirjana; Dosen, Kosta; Petric, Zoran

1999-01-01

The paper presents a cut-elimination procedure for intuitionistic propositional logic in which cut is eliminated directly, without introducing the multiple-cut rule mix, and in which pushing cut above contraction is one of the reduction steps. The presentation of this procedure is preceded by an analysis of Gentzen's mix-elimination procedure, made in the perspective of permuting cut with contraction. It is also shown that in the absence of implication, pushing cut above contraction doesn't p...

A non-linear branch and cut method for solving discrete minimum compliance problems to global optimality

DEFF Research Database (Denmark)

Stolpe, Mathias; Bendsøe, Martin P.

2007-01-01

This paper present some initial results pertaining to a search for globally optimal solutions to a challenging benchmark example proposed by Zhou and Rozvany. This means that we are dealing with global optimization of the classical single load minimum compliance topology design problem with a fixed...... finite element discretization and with discrete design variables. Global optimality is achieved by the implementation of some specially constructed convergent nonlinear branch and cut methods, based on the use of natural relaxations and by applying strengthening constraints (linear valid inequalities...

Model for Reggeon-Pomeranchukon cuts

International Nuclear Information System (INIS)

Chia, S.

1977-01-01

A model is presented for calculating Reggeon-Pomeranchukon cuts, making use explicitly of the Mandelstam diagram. External spins are treated in a natural way. Calculation for the general case is outlined and it is shown that in practical application the cut can be calculated in a standard way. Cuts associated with the exchanges of π, rho, B, and A 2 are considered, and characteristics of the RP cuts, as well as the structure functions, are extracted and discussed. It is found that the model differs considerably from the absorption model. Two suppression schemes are operative which control the magnitudes of cut contributions to amplitudes with ''naturality'' opposite to the Reggeon. The πP cut is found to be a unique case because of the smallness of the pion mass. In general, the RP cuts are self-conspiratorial. At very high energies, all cuts, except πP cut, exhibit quasifactorization

An FMS Dynamic Production Scheduling Algorithm Considering Cutting Tool Failure and Cutting Tool Life

International Nuclear Information System (INIS)

Setiawan, A; Wangsaputra, R; Halim, A H; Martawirya, Y Y

2016-01-01

This paper deals with Flexible Manufacturing System (FMS) production rescheduling due to unavailability of cutting tools caused either of cutting tool failure or life time limit. The FMS consists of parallel identical machines integrated with an automatic material handling system and it runs fully automatically. Each machine has a same cutting tool configuration that consists of different geometrical cutting tool types on each tool magazine. The job usually takes two stages. Each stage has sequential operations allocated to machines considering the cutting tool life. In the real situation, the cutting tool can fail before the cutting tool life is reached. The objective in this paper is to develop a dynamic scheduling algorithm when a cutting tool is broken during unmanned and a rescheduling needed. The algorithm consists of four steps. The first step is generating initial schedule, the second step is determination the cutting tool failure time, the third step is determination of system status at cutting tool failure time and the fourth step is the rescheduling for unfinished jobs. The approaches to solve the problem are complete-reactive scheduling and robust-proactive scheduling. The new schedules result differences starting time and completion time of each operations from the initial schedule. (paper)

Decrease of FIB-induced lateral damage for diamond tool used in nano cutting

Energy Technology Data Exchange (ETDEWEB)

Wu, Wei [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Xu, Zongwei, E-mail: zongweixu@163.com [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Fang, Fengzhou, E-mail: fzfang@gmail.com [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Liu, Bing; Xiao, Yinjing; Chen, Jinping [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Wang, Xibin [School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081 (China); Liu, Hongzhong [State Key Laboratory for Manufacturing Systems Engineering, Xi’an Jiaotong University, Xi’an 710049 (China)

2014-07-01

Highlights: • We mainly aim to characterize and decrease the FIB-induced damage on diamond tool. • Raman and XPS methods were used to characterize the nanoscale FIB-induced damage. • Lower energy FIB can effectively lessen the FIB-induced damage on diamond tool. • The diamond tools’ performance was greatly improved after FIB process optimization. • 6 nm chip thickness of copper was achieved by diamond tool with 22 nm edge radius. - Abstract: Diamond cutting tools with nanometric edge radius used in ultra-precision machining can be fabricated by focused ion beam (FIB) technology. However, due to the nanoscale effects, the diamond tools performance and the cutting edge lifetime in nano cutting would be degraded because of the FIB-induced nanoscale lateral damage. In this study, the methods of how to effectively characterize and decrease the FIB-induced lateral damage for diamond tool are intensively studied. Based on the performance optimization diamond machining tools, the controllable chip thickness of less than 10 nm was achieved on a single-crystal copper in nano cutting. In addition, the ratio of minimum thickness of chip (MTC) to tool edge radius of around 0.3–0.4 in nano cutting is achieved. Methods for decreasing the FIB-induced damage on diamond tools and adding coolant during the nano cutting are very beneficial in improving the research of nano cutting and MTC. The nano cutting experiments based on the sharp and high performance of diamond tools would validate the nano cutting mechanisms that many molecular dynamic simulation studies have put forward and provide new findings for nano cutting.

Whole-Body and Hepatic Insulin Resistance in Obese Children

Science.gov (United States)

Ibarra-Reynoso, Lorena del Rocío; Pisarchyk, Liudmila; Pérez-Luque, Elva Leticia; Garay-Sevilla, Ma. Eugenia; Malacara, Juan Manuel

2014-01-01

Background Insulin resistance may be assessed as whole body or hepatic. Objective To study factors associated with both types of insulin resistance. Methods Cross-sectional study of 182 obese children. Somatometric measurements were registered, and the following three adiposity indexes were compared: BMI, waist-to-height ratio and visceral adiposity. Whole-body insulin resistance was evaluated using HOMA-IR, with 2.5 as the cut-off point. Hepatic insulin resistance was considered for IGFBP-1 level quartiles 1 to 3 (HOMA-IR was negatively associated with IGFBP-1 and positively associated with BMI, triglycerides, leptin and mother's BMI. Girls had increased HOMA-IR. IGFBP-1 was negatively associated with waist-to-height ratio, age, leptin, HOMA-IR and IGF-I. We did not find HOMA-IR or IGFBP-1 associated with fatty liver. Conclusion In school-aged children, BMI is the best metric to predict whole-body insulin resistance, and waist-to-height ratio is the best predictor of hepatic insulin resistance, indicating that central obesity is important for hepatic insulin resistance. The reciprocal negative association of IGFBP-1 and HOMA-IR may represent a strong interaction of the physiological processes of both whole-body and hepatic insulin resistance. PMID:25411786

Advanced cutting techniques: laser and fissuration cutting

International Nuclear Information System (INIS)

Migliorati, B.; Gay, P.

1984-01-01

Experimental tests have been performed using CO 2 laser with output power 1 to 15 kW to evaluate the effect of varying the following parameters: material (carbon steel Fe 42 C, stainless steel AISI 304, concrete), laser power, beam characteristics, work piece velocity, gas type and distribution on the laser interaction zone. In the case of concrete, drilling depths of 80 mm were obtained in a few seconds using a 10 kW laser beam. Moreover pieces of 160 mm were cut at 0.01 meters per minute. Results with carbon steel indicated maximum thicknesses of 110 mm, cut at 0.01 meters per minute with 10 kW, depths about 20% lower were obtained with the AISI 304 stainless steel. A parallel investigation was aimed at characterizing particulate emission during the laser cutting process. At the end of the research it was possible to elaborate a preliminary proposal concerning a laser based dismantling system for the application to a typical Nuclear Power Station. (author)

Determining cutting efficiency of nickel-titanium coronal flaring instruments used in lateral action.

Science.gov (United States)

Peters, O A; Morgental, R D; Schulze, K A; Paqué, F; Kopper, P M P; Vier-Pelisser, F V

2014-06-01

To develop a method to evaluate the cutting behaviour of nickel-titanium (NiTi) coronal flaring instruments. BioRaCe BR0 (BR), HyFlex CM 1 (HY), ProFile OS No. 2 (PF) and ProTaper Sx (PT) instruments were used in simulated coronal flaring using a lateral action against bovine dentine blocks, at 250 and 500 rpm. Cutting efficiency was assessed by three methods: first, areas of notches produced by instruments were directly measured under a stereomicroscope. Second, dentine specimens were then analysed by surface profilometry to determine the maximum cutting depth and finally by microcomputed tomography to assess the volume of removed dentine. Data were compared using parametric tests with the significance level set at 0.05. For all three methods, HY and PF were the most and the least cutting-efficient instruments, respectively (P wire, was the most efficient instrument, and increased rotational speed was associated with increased cutting efficiency. © 2013 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Fractal characteristic in the wearing of cutting tool

Science.gov (United States)

Mei, Anhua; Wang, Jinghui

1995-11-01

This paper studies the cutting tool wear with fractal geometry. The wearing image of the flank has been collected by machine vision which consists of CCD camera and personal computer. After being processed by means of preserving smoothing, binary making and edge extracting, the clear boundary enclosing the worn area has been obtained. The fractal dimension of the worn surface is calculated by the methods called `Slit Island' and `Profile'. The experiments and calciating give the conclusion that the worn surface is enclosed by a irregular boundary curve with some fractal dimension and characteristics of self-similarity. Furthermore, the relation between the cutting velocity and the fractal dimension of the worn region has been submitted. This paper presents a series of methods for processing and analyzing the fractal information in the blank wear, which can be applied to research the projective relation between the fractal structure and the wear state, and establish the fractal model of the cutting tool wear.

Development and characterization of Si3N4 coated AlCrN ceramic cutting tool

International Nuclear Information System (INIS)

Souza, J.V.C.; Nono, M.C.A.; Martins, G.V.; Machado, J.P.B.; Silva, O.M.M.

2009-01-01

Nowadays, silicon nitride based cutting tools are used to machine cast iron from the automotive industry and nickel superalloys from the aero industries. Advances in manufacturing technologies (increased cutting speeds, dry machining, etc.) induced the fast commercial growth of physical vapor deposition (PVD) coatings for cutting tools, in order to increase their life time. In this work, a new composition of the Si 3 N 4 ceramic cutting tool was developed, characterized and subsequently coated, using a PVD process, with aluminum chromium nitride (AlCrN). The Si 3 N 4 substrate properties were analyzed by XRD, AFM, hardness and fracture toughness. The AlCrN coating was analyzed by AFM, grazing incidence X-ray diffraction (GIXRD) and hardness. The results showed that this PVD coating could be formed homogeneously, without cracks and promoted a higher surface hardness to the insert and consequently it can produce a better wear resistance during its application on high speed machining. (author)

Slope failures evaluation and landslides investigation using 2-D resistivity method

Directory of Open Access Journals (Sweden)

M.M. Nordiana

2018-06-01

Full Text Available Slope failure is a complex phenomenon that may caused to landslides. Buildings and infrastructure such as transportation facilities and pipelines located within the boundaries of a landslide can be damaged or destroyed. Slope failure classification and various factors contributing to the instability using 2-D resistivity survey conducted in Selangor, Malaysia are described. Six 2-D resistivity survey lines with 5 m minimum electrode spacing using Pole-dipole array were performed. The data were processed using Res2Dinv and surfer10 software to evaluate the subsurface characteristics. The 2-D resistivity results show that the subsurface consist of two main zones. The first zone was alluvium or highly weathered with resistivity value of 100–1000 Ω m and depth of >30 m. This zone consists of saturated area with resistivity value of 1–100 Ω m and boulders with resistivity value of 1200–7000 Ω m. The second zone with resistivity value of >7000 Ω m was interpreted as granitic bedrock. The study area was characterized by saturated zones, highly weathered zone, highly contain of sand and boulders that will trigger slope failure in the survey area. This will cause to low strength of soil, debris flow and movement of earth. On the basis of the case examples described, 2-D resistivity method is categorized into desirable and useful method in determination of slope failure and future assessments. Keywords: Slope failure, Landslides, 2-D resistivity, Saturated, Boulders

Cutting of metal components by intergranular cracking

International Nuclear Information System (INIS)

Chavand, J.; Gauthier, A.; Lopez, J.J.; Tanis, G.

1985-01-01

The objective of this contract was to study a new steel-sheet cutting technique for dismantling nuclear installations without in principle producing secondary waste. This technique is based on intergranular cracking of steel induced by the combined action of penetration of molten metal into the steel and application of a mechanical load. Cutting has been achieved for stainless-steel sheets with thicknesses ranging from a few mm to 50 mm and for carbon-steel plates with thicknesses between 20 and 60 mm. For carbon steel is seems possible that components as thick as 100 mm can be cut. The tests have permitted selection of the heating methods and determination of the cracking parameters for the materials and range of thickness studied. In the case of thin sheets, results were obtained for cutting in varied positions suited to the techniques of dismantling in hot cells. A temperature-measuring system using an infrared camera has been developed to determine the variation of the temperature field established in the component. In association with the three-dimensional computation code COCO developed by the CEA, this system permits prediction of the changes in stresses in the cracked zone when the cutting parameters are modified. 34 figs

A review of cutting mechanics and modeling techniques for biological materials.

Science.gov (United States)

Takabi, Behrouz; Tai, Bruce L

2017-07-01

This paper presents a comprehensive survey on the modeling of tissue cutting, including both soft tissue and bone cutting processes. In order to achieve higher accuracy in tissue cutting, as a critical process in surgical operations, the meticulous modeling of such processes is important in particular for surgical tool development and analysis. This review paper is focused on the mechanical concepts and modeling techniques utilized to simulate tissue cutting such as cutting forces and chip morphology. These models are presented in two major categories, namely soft tissue cutting and bone cutting. Fracture toughness is commonly used to describe tissue cutting while Johnson-Cook material model is often adopted for bone cutting in conjunction with finite element analysis (FEA). In each section, the most recent mathematical and computational models are summarized. The differences and similarities among these models, challenges, novel techniques, and recommendations for future work are discussed along with each section. This review is aimed to provide a broad and in-depth vision of the methods suitable for tissue and bone cutting simulations. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

Chemical monitoring of mud products on drilled cuttings

International Nuclear Information System (INIS)

Hughes, T.L.; Jones, T.G.J.; Tomkins, P.G.; Gilmour, A.; Houwen, O.H.; Sanders, M.

1991-01-01

An increasing area of concern for offshore drilling practices in the environmental impact of discharged drilled cuttings contaminated with drilling fluids. The standard retort analysis is of limited accuracy and chemical specificity. Anticipating future requirements for a more complete accounting of mud chemicals discharged to the environment, we present here results for chemical monitoring using a modern comprehensive chemical analysis technique. Fourier transform infrared (FT-IR) spectrometry. In this paper description is given of sampling methods found to be practical and the main calibration requirements are discussed. The techniques developed in the course of this work give a good mineralogical breakdown of mud solids (commercial and drilled solids) in addition to the environmentally relevant measurements relating to mud on cuttings. The possibility of using the new technique for the rigsite monitoring of drilling cuttings is demonstrated. Cuttings samples simultaneously from the flow line, shaker screen, desilter and mud cleaner were analyzed. It is found that mud polymers and other organic additives can be measured with sufficient accuracy to measure the removal of mud products by discharged cuttings. The technique is also applicable to quantify the losses of oil-based mud on cuttings. Field testing has shown that the instrumentation used in sufficiently robust and simple to use for rig-site application

Evaluation of laser cutting process with auxiliary gas pressure by soft computing approach

Science.gov (United States)

Lazov, Lyubomir; Nikolić, Vlastimir; Jovic, Srdjan; Milovančević, Miloš; Deneva, Heristina; Teirumenieka, Erika; Arsic, Nebojsa

2018-06-01

Evaluation of the optimal laser cutting parameters is very important for the high cut quality. This is highly nonlinear process with different parameters which is the main challenge in the optimization process. Data mining methodology is one of most versatile method which can be used laser cutting process optimization. Support vector regression (SVR) procedure is implemented since it is a versatile and robust technique for very nonlinear data regression. The goal in this study was to determine the optimal laser cutting parameters to ensure robust condition for minimization of average surface roughness. Three cutting parameters, the cutting speed, the laser power, and the assist gas pressure, were used in the investigation. As a laser type TruLaser 1030 technological system was used. Nitrogen as an assisted gas was used in the laser cutting process. As the data mining method, support vector regression procedure was used. Data mining prediction accuracy was very high according the coefficient (R2) of determination and root mean square error (RMSE): R2 = 0.9975 and RMSE = 0.0337. Therefore the data mining approach could be used effectively for determination of the optimal conditions of the laser cutting process.

Shaping Cutter Original Profile for Fine-module Ratchet Teeth Cutting

Science.gov (United States)

Sharkov, O. V.; Koryagin, S. I.; Velikanov, N. L.

2018-03-01

The methods for determining geometric characteristics of a theoretical original profile of the cutter for cutting ratchet teeth with a module of 0.3–1.0 mm are considered in the article. Design models describing the shaping process of cutting edges of cutter teeth are developed. Systems of expressions for determining coordinates of the points of front and back edges of cutter teeth; the workpiece angles of rotation during the cutting process; the minimum cutter radius are received. The basic data when using the proposed technique are: radii of circumferences passing through cavities of cutter teeth and external cut teeth; the gradient angle and length of straight section of the front edge of a cut tooth; angles of rotation of the cutter and the workpiece at the moment of shaping.

An innovative method for ideal and resistive MHD stability analysis of tokamaks

International Nuclear Information System (INIS)

Tokuda, S.

2001-01-01

An advanced asymptotic matching method of ideal and resistive MHD stability analysis in tokamak is reported. The report explains a solution method of two-dimensional Newcomb equation, dispersion relation for an unstable ideal MHD mode in tokamak, and a new scheme for solving resistive MHD inner layer equations as an initial-value problem. (author)

An innovative method for ideal and resistive MHD stability analysis of tokamaks

International Nuclear Information System (INIS)

Tokuda, S.

2001-01-01

An advanced asymptotic matching method of ideal and resistive MHD stability analysis in tokamaks is reported. A solution method for the two dimensional Newcomb equation, a dispersion relation for an unstable ideal MHD mode in tokamaks and a new scheme for solving resistive MHD inner layer equations as an initial value problem are reported. (author)

A theoretical model for predicting the Peak Cutting Force of conical picks

Directory of Open Access Journals (Sweden)

Gao Kuidong

2014-01-01

Full Text Available In order to predict the PCF (Peak Cutting Force of conical pick in rock cutting process, a theoretical model is established based on elastic fracture mechanics theory. The vertical fracture model of rock cutting fragment is also established based on the maximum tensile criterion. The relation between vertical fracture angle and associated parameters (cutting parameter  and ratio B of rock compressive strength to tensile strength is obtained by numerical analysis method and polynomial regression method, and the correctness of rock vertical fracture model is verified through experiments. Linear regression coefficient between the PCF of prediction and experiments is 0.81, and significance level less than 0.05 shows that the model for predicting the PCF is correct and reliable. A comparative analysis between the PCF obtained from this model and Evans model reveals that the result of this prediction model is more reliable and accurate. The results of this work could provide some guidance for studying the rock cutting theory of conical pick and designing the cutting mechanism.

Liver Segmentation Based on Snakes Model and Improved GrowCut Algorithm in Abdominal CT Image

Directory of Open Access Journals (Sweden)

Huiyan Jiang

2013-01-01

Full Text Available A novel method based on Snakes Model and GrowCut algorithm is proposed to segment liver region in abdominal CT images. First, according to the traditional GrowCut method, a pretreatment process using K-means algorithm is conducted to reduce the running time. Then, the segmentation result of our improved GrowCut approach is used as an initial contour for the future precise segmentation based on Snakes model. At last, several experiments are carried out to demonstrate the performance of our proposed approach and some comparisons are conducted between the traditional GrowCut algorithm. Experimental results show that the improved approach not only has a better robustness and precision but also is more efficient than the traditional GrowCut method.

Development of plasma cutting process at observation of environmental requirements

International Nuclear Information System (INIS)

Czech, J.; Matusiak, J.; Pasek-Siurek, H.

1997-01-01

Plasma cutting is one of the basic methods for thermal cutting of metals. It is characterized by high productivity and quality of the cut surface. However, the plasma cutting process is one of the most harmful processes for environment and human health. It results from many agents being a potential environmental risk The large amount of dust and gases emitted during the process as well as an intensive radiation of electric arc and excessive noise are considered as the most harmful hazards. The existing ventilation and filtration systems are not able to solve all problems resulting from the process. Plasma cutting under water is worthy of notice, especially during an advancement of plasma cutting process, because of human safety and environment protection. Such a solution allows to reduce considerably the emission of dust and gases, as well as to decrease the noise level and ultraviolet radiation. An additional advantage of underwater plasma cutting is a reduction in the width of material heating zone and a decrease in strains of elements being cut. However, the productivity of this process is a little lower what results in an increase in cutting cost. In the paper, it has been presented the results of the investigations made at the Institute of Welding in Gliwice on the area of plasma cutting equipment with energy-saving inverter power supplies used in automated processes of underwater plasma cutting as well as the results of testing of welding environment contamination and safety hazards. (author)

Female genital cutting.

Science.gov (United States)

Perron, Liette; Senikas, Vyta; Burnett, Margaret; Davis, Victoria

2013-11-01

To strengthen the national framework for care of adolescents and women affected by female genital cutting (FGC) in Canada by providing health care professionals with: (1) information intended to strengthen their knowledge and understanding of the practice; (2) directions with regard to the legal issues related to the practice; (3) clinical guidelines for the management of obstetric and gynaecological care, including FGC related complications; and (4) guidance on the provision of culturally competent care to adolescents and women with FGC. Published literature was retrieved through searches of PubMed, CINAHL, and The Cochrane Library in September 2010 using appropriate controlled vocabulary (e.g., Circumcision, Female) and keywords (e.g., female genital mutilation, clitoridectomy, infibulation). We also searched Social Science Abstracts, Sociological Abstracts, Gender Studies Database, and ProQuest Dissertations and Theses in 2010 and 2011. There were no date or language restrictions. Searches were updated on a regular basis and incorporated in the guideline to December 2011. Grey (unpublished) literature was identified through searching the websites of health technology assessment and health technology-related agencies, clinical practice guideline collections, clinical trial registries, and national and international medical specialty societies. The quality of evidence in this document was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care (Table 1). Summary Statements 1. Female genital cutting is internationally recognized as a harmful practice and a violation of girls' and women's rights to life, physical integrity, and health. (II-3) 2. The immediate and long-term health risks and complications of female genital cutting can be serious and life threatening. (II-3) 3. Female genital cutting continues to be practised in many countries, particularly in sub-Saharan Africa, Egypt, and Sudan. (II-3) 4. Global migration

IMPORTANCE, Minimal Cut Sets and System Availability from Fault Tree Analysis

International Nuclear Information System (INIS)

Lambert, H. W.

1987-01-01

1 - Description of problem or function: IMPORTANCE computes various measures of probabilistic importance of basic events and minimal cut sets to a fault tree or reliability network diagram. The minimal cut sets, the failure rates and the fault duration times (i.e., the repair times) of all basic events contained in the minimal cut sets are supplied as input data. The failure and repair distributions are assumed to be exponential. IMPORTANCE, a quantitative evaluation code, then determines the probability of the top event and computes the importance of minimal cut sets and basic events by a numerical ranking. Two measures are computed. The first describes system behavior at one point in time; the second describes sequences of failures that cause the system to fail in time. All measures are computed assuming statistical independence of basic events. In addition, system unavailability and expected number of system failures are computed by the code. 2 - Method of solution: Seven measures of basic event importance and two measures of cut set importance can be computed. Birnbaum's measure of importance (i.e., the partial derivative) and the probability of the top event are computed using the min cut upper bound. If there are no replicated events in the minimal cut sets, then the min cut upper bound is exact. If basic events are replicated in the minimal cut sets, then based on experience the min cut upper bound is accurate if the probability of the top event is less than 0.1. Simpson's rule is used in computing the time-integrated measures of importance. Newton's method for approximating the roots of an equation is employed in the options where the importance measures are computed as a function of the probability of the top event, and a shell sort puts the output in descending order of importance

Photonic mesophases from cut rod rotators

Energy Technology Data Exchange (ETDEWEB)

Stelson, Angela C.; Liddell Watson, Chekesha M., E-mail: cml66@cornell.edu [Materials Science and Engineering, Cornell University, Ithaca, New York 14853 (United States); Avendano, Carlos [Chemical Engineering and Analytical Science, The University of Manchester, Manchester M13 9PL (United Kingdom)

2016-01-14

The photonic band properties of random rotator mesophases are calculated using supercell methods applied to cut rods on a hexagonal lattice. Inspired by the thermodynamic mesophase for anisotropic building blocks, we vary the shape factor of cut fraction for the randomly oriented basis. We find large, stable bandgaps with high gap isotropy in the inverted and direct structures as a function of cut fraction, dielectric contrast, and filling fraction. Bandgap sizes up to 34.5% are maximized at high dielectric contrast for rods separated in a matrix. The bandgaps open at dielectric contrasts as low as 2.0 for the transverse magnetic polarization and 2.25 for the transverse electric polarization. Additionally, the type of scattering that promotes the bandgap is correlated with the effect of disorder on bandgap size. Slow light properties are investigated in waveguide geometry and slowdown factors up to 5 × 10{sup 4} are found.

Extension without Cut

OpenAIRE

Straßburger , Lutz

2012-01-01

International audience; In proof theory one distinguishes sequent proofs with cut and cut-free sequent proofs, while for proof complexity one distinguishes Frege-systems and extended Frege-systems. In this paper we show how deep inference can provide a uniform treatment for both classifications, such that we can define cut-free systems with extension, which is neither possible with Frege-systems, nor with the sequent calculus. We show that the propositional pigeon-hole principle admits polyno...

The role of the microfissuration of the rock matrix in the abrasion resistance of ornamental granitic rocks

Science.gov (United States)

Rodríguez-Rey, Angel; Sanchez-Delgado, Nuria; Camino, Clara; Calleja, Lope; Ruiz de Argandoña, Vicente G.; Setien, Alexia

2015-04-01

The microcrack density and the abrasion resistance of five ornamental granites (Albero, Gris Alba, Mondariz, Rosa Porriño and Traspieles) from Galicia (NW Spain) have been quantified as part of a research aimed to interpret the cuttability of the rocks in relation to the petrophysical properties of the rock matrix. Large blocks from the quarries have been cut with an industrial saw and the microcrack density and the abrasion resistance have been measured in two surfaces: H, parallel to the cut surface; T, perpendicular both to the cut surface and the cutting direction. Both planes are perpendicular to the rift plane, as it is known in quarry works. The microcrack density has been quantified following an stereological procedure applied to polished sections imaged under scanning electron microscopy. The magnification of the images allowed the study of microcracks as narrow as 2 microns in aperture. The density has been quantified in terms of length of microcrack traces per surface unit so possible anisotropies of the microcrack network could be detected. The obtained values are in the typical range for this type of rocks although the Traspieles granite shows a higher value due to its weathering degree (H: 5.11, T: 5.37 mm/mm2). The values measured in the two surfaces (H and T) are quite similar in four of the rocks; only the Albero granite shows a marked anisotropy (H: 2.76 T: 3.53 mm/mm2). The abrasion resistance of the rocks has been measured following the european standard EN 14157:2004 using the capon method. The rocks can be classified in two groups according to their abrasion resistance. Rosa Porriño, Gris Alba and Mondariz granites are the more resistant to abrasion with values around 16-17 mm. Albero and Traspieles granites are less resistant with values higher than 19 mm. The results show a good correlation between the microcrack density and the abrasion resistance. As can be expected the rocks with high microcrack density show low abrasion resistance. The

Assessment of antibiotic resistance of Escherichia coli isolates and screening of Salmonella spp. in wild ungulates from Portugal.

Science.gov (United States)

Dias, Diana; Torres, Rita T; Kronvall, Göran; Fonseca, Carlos; Mendo, Sónia; Caetano, Tânia

2015-09-01

Antibiotic resistance is an emerging global problem. Wild animals are rarely exposed to antibiotics and therefore low levels of antibiotic resistance are expected. However, the growing interactions of these animals with humans and livestock may have a huge impact on their bacterial flora. This study aimed to assess the levels of antibiotic resistance in Escherichia coli isolated from widespread wild ungulates in Portugal. The interpretation of inhibition zone diameters was performed according to clinical breakpoints and epidemiological cut-offs, determined with the normalized resistance interpretation (NRI) method. For clinical breakpoints, 16% of the isolates were resistant to at least one antibiotic, including ampicillin (10%), tetracycline (9%), streptomycin (5%) co-trimoxazole (4%), amoxicillin/clavulanic acid (1%) and cefoxitin (1%). The levels of resistance detected in E. coli strains isolated from wild boar were statistically different for ampicillin and co-trimoxasol. According to NRI cut-offs, 10% of the population showed a non-wild-type phenotype against at least one antibiotic, also including tetracycline (9%), co-trimoxazole (6%), streptomycin (4%), ampicillin (2%) and amoxicillin/clavulanic acid (1%). Considering this parameter of comparison, no statistically different levels of resistance were identified between E. coli recovered from the three wild ungulates. Screening of Salmonella spp., which can be potentially pathogenic, was also performed, revealing that its prevalence was very low (1.5%). The study demonstrated that wild ungulates from Portugal are also reservoirs of antibiotic-resistant bacteria. Copyright © 2015 Institut Pasteur. Published by Elsevier Masson SAS. All rights reserved.

Applicability of AWJ technique for dismantling reactor of the Fukushima Daiichi Nuclear Power Station. Cutting test of imitation of fuel debris and optimization of the cutting condition

International Nuclear Information System (INIS)

Maruyama, Shin-ichiro; Watatani, Satoshi

2016-01-01

Based on findings during recovery works that followed the accident at Three Mile Island Station 2, it is assumed that the reactor internals at the Fukushima Daiichi Nuclear Power Station (1F) have complex geometries intermixed with melted fuel and confined in limited spaces. Accordingly, abrasive water jet (AWJ) cutting method is considered to be a promising technique that can be safely and reasonably used for cutting and removing reactor internals. The authors conducted tests to examine the possibility of application and to solve the problems of this technique. In the tests imitation of fuel debris and optimization of the cutting condition is used. The test result made the measures for some of the associated issues clear, and demonstrated that AWJ cutting method is assumed as one of the promising techniques for removing reactor internals. (author)

Direct Extraction of InP/GaAsSb/InP DHBT Equivalent-Circuit Elements From S-Parameters Measured at Cut-Off and Normal Bias Conditions

DEFF Research Database (Denmark)

Johansen, Tom Keinicke; Leblanc, Rémy; Poulain, Julien

2016-01-01

A unique direct parameter extraction method for the small-signal equivalent-circuit model of InP/GaAsSb/InP double heterojunction bipolar transistors (DHBTs) is presented. $S$-parameters measured at cut-off bias are used, at first, to extract the distribution factor $X_{0}$ for the base-collector......A unique direct parameter extraction method for the small-signal equivalent-circuit model of InP/GaAsSb/InP double heterojunction bipolar transistors (DHBTs) is presented. $S$-parameters measured at cut-off bias are used, at first, to extract the distribution factor $X_{0}$ for the base......-collector capacitance at zero collector current and the collector-to-emitter overlap capacitance $C_{ceo}$ present in InP DHBT devices. Low-frequency $S$-parameters measured at normal bias conditions then allows the extraction of the external access resistances $R_{bx}$, $R_{e}$, and $R_{cx}$ as well as the intrinsic...

A column generation approach to a carpentry cutting stock problem ...

African Journals Online (AJOL)

The carpentry sector like any other industry is faced with a cutting stock problem to minimize incurred waste. The main purpose of this project was to develop a mathematical model which will solve the cutting stock problem using column generation approach for Ashtons Company in Chinhoyi. The interview method was ...