WorldWideScience

Sample records for method proposes full

  1. 24 CFR 941.304 - Full proposal content.

    Science.gov (United States)

    2010-04-01

    ... with all applicable Federal relocation requirements; (j) Life-cycle analysis. For new construction and... cooling systems, and which shall include a life-cycle cost analysis of the installation, maintenance and... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Full proposal content. 941.304...

  2. Simulations of The Dalles Dam Proposed Full Length Spillwall

    Energy Technology Data Exchange (ETDEWEB)

    Rakowski, Cynthia L.; Perkins, William A.; Richmond, Marshall C.; Serkowski, John A.

    2008-02-25

    This report presents results of a computational fluid dynamics (CFD) modeling study to evaluatethe impacts of a full-length spillwall at The Dalles Dam. The full-length spillwall is being designed and evaluated as a structural means to improve tailrace egress and thus survival of juvenile fish passing through the spillway. During the course of this study, a full-length spillwall at Bays 6/7 and 8/9 were considered. The U.S. Army Corps of Engineers (USACE) has proposed extending the spillwall constructed in the stilling basin between spillway Bays 6 and 7 about 590 ft farther downstream. It is believed that the extension of the spillwall will improve egress conditions for downstream juvenile salmonids by moving them more rapidly into the thalweg of the river hence reducing their exposure to predators. A numerical model was created, validated, and applied the The Dalles Dam tailrace. The models were designed to assess impacts to flow, tailrace egress, navigation, and adult salmon passage of a proposed spill wall extension. The more extensive model validation undertaken in this study greatly improved our confidence in the numerical model to represent the flow conditions in The Dalles tailrace. This study used these validated CFD models to simulate the potential impacts of a spillwall extension for The Dalles Dam tailrace for two locations. We determined the following: (1)The construction of an extended wall (between Bays 6/7) will not adversely impact entering or exiting the navigation lock. Impact should be less if a wall were constructed between Bays 8/9. (2)The construction of a wall between Bays 6/7 will increase the water surface elevation between the wall and the Washington shore. Although the increased water surface elevation would be beneficial to adult upstream migrants in that it decreases velocities on the approach to the adult ladder, the increased flow depth would enhance dissolved gas production, impacting potential operations of the project because of

  3. Evaluation of full-scope simulator testing methods

    Energy Technology Data Exchange (ETDEWEB)

    Feher, M P; Moray, N; Senders, J W; Biron, K [Human Factors North Inc., Toronto, ON (Canada)

    1995-03-01

    This report discusses the use of full scope nuclear power plant simulators in licensing examinations for Unit First Operators of CANDU reactors. The existing literature is reviewed, and an annotated bibliography of the more important sources provided. Since existing methods are judged inadequate, conceptual bases for designing a system for licensing are discussed, and a method proposed which would make use of objective scoring methods based on data collection in full-scope simulators. A field trial of such a method is described. The practicality of such a method is critically discussed and possible advantages of subjective methods of evaluation considered. (author). 32 refs., 1 tab., 4 figs.

  4. Evaluation of full-scope simulator testing methods

    International Nuclear Information System (INIS)

    Feher, M.P.; Moray, N.; Senders, J.W.; Biron, K.

    1995-03-01

    This report discusses the use of full scope nuclear power plant simulators in licensing examinations for Unit First Operators of CANDU reactors. The existing literature is reviewed, and an annotated bibliography of the more important sources provided. Since existing methods are judged inadequate, conceptual bases for designing a system for licensing are discussed, and a method proposed which would make use of objective scoring methods based on data collection in full-scope simulators. A field trial of such a method is described. The practicality of such a method is critically discussed and possible advantages of subjective methods of evaluation considered. (author). 32 refs., 1 tab., 4 figs

  5. A proposed method to estimate premorbid full scale intelligence quotient (FSIQ) for the Canadian Wechsler Intelligence Scale for Children-Fourth Edition (WISC-IV) using demographic and combined estimation procedures.

    Science.gov (United States)

    Schoenberg, Mike R; Lange, Rael T; Saklofske, Donald H

    2007-11-01

    Establishing a comparison standard in neuropsychological assessment is crucial to determining change in function. There is no available method to estimate premorbid intellectual functioning for the Wechsler Intelligence Scale for Children-Fourth Edition (WISC-IV). The WISC-IV provided normative data for both American and Canadian children aged 6 to 16 years old. This study developed regression algorithms as a proposed method to estimate full-scale intelligence quotient (FSIQ) for the Canadian WISC-IV. Participants were the Canadian WISC-IV standardization sample (n = 1,100). The sample was randomly divided into two groups (development and validation groups). The development group was used to generate regression algorithms; 1 algorithm only included demographics, and 11 combined demographic variables with WISC-IV subtest raw scores. The algorithms accounted for 18% to 70% of the variance in FSIQ (standard error of estimate, SEE = 8.6 to 14.2). Estimated FSIQ significantly correlated with actual FSIQ (r = .30 to .80), and the majority of individual FSIQ estimates were within +/-10 points of actual FSIQ. The demographic-only algorithm was less accurate than algorithms combining demographic variables with subtest raw scores. The current algorithms yielded accurate estimates of current FSIQ for Canadian individuals aged 6-16 years old. The potential application of the algorithms to estimate premorbid FSIQ is reviewed. While promising, clinical validation of the algorithms in a sample of children and/or adolescents with known neurological dysfunction is needed to establish these algorithms as a premorbid estimation procedure.

  6. 77 FR 22564 - Proposed Collection; Comment Request; Safety Standards for Full-Size Baby Cribs and Non-Full-Size...

    Science.gov (United States)

    2012-04-16

    ... CONSUMER PRODUCT SAFETY COMMISSION [Docket No. CPSC-2012-0019] Proposed Collection; Comment Request; Safety Standards for Full- Size Baby Cribs and Non-Full-Size Baby Cribs; Compliance Form AGENCY... safety standards for full-size and non-full-size baby cribs in response to the direction under section...

  7. A Proposed Arabic Handwritten Text Normalization Method

    Directory of Open Access Journals (Sweden)

    Tarik Abu-Ain

    2014-11-01

    Full Text Available Text normalization is an important technique in document image analysis and recognition. It consists of many preprocessing stages, which include slope correction, text padding, skew correction, and straight the writing line. In this side, text normalization has an important role in many procedures such as text segmentation, feature extraction and characters recognition. In the present article, a new method for text baseline detection, straightening, and slant correction for Arabic handwritten texts is proposed. The method comprises a set of sequential steps: first components segmentation is done followed by components text thinning; then, the direction features of the skeletons are extracted, and the candidate baseline regions are determined. After that, selection of the correct baseline region is done, and finally, the baselines of all components are aligned with the writing line.  The experiments are conducted on IFN/ENIT benchmark Arabic dataset. The results show that the proposed method has a promising and encouraging performance.

  8. Full Waveform Inversion Using Oriented Time Migration Method

    KAUST Repository

    Zhang, Zhendong

    2016-04-12

    Full waveform inversion (FWI) for reflection events is limited by its linearized update requirements given by a process equivalent to migration. Unless the background velocity model is reasonably accurate the resulting gradient can have an inaccurate update direction leading the inversion to converge into what we refer to as local minima of the objective function. In this thesis, I first look into the subject of full model wavenumber to analysis the root of local minima and suggest the possible ways to avoid this problem. And then I analysis the possibility of recovering the corresponding wavenumber components through the existing inversion and migration algorithms. Migration can be taken as a generalized inversion method which mainly retrieves the high wavenumber part of the model. Conventional impedance inversion method gives a mapping relationship between the migration image (high wavenumber) and model parameters (full wavenumber) and thus provides a possible cascade inversion strategy to retrieve the full wavenumber components from seismic data. In the proposed approach, consider a mild lateral variation in the model, I find an analytical Frechet derivation corresponding to the new objective function. In the proposed approach, the gradient is given by the oriented time-domain imaging method. This is independent of the background velocity. Specifically, I apply the oriented time-domain imaging (which depends on the reflection slope instead of a background velocity) on the data residual to obtain the geometrical features of the velocity perturbation. Assuming that density is constant, the conventional 1D impedance inversion method is also applicable for 2D or 3D velocity inversion within the process of FWI. This method is not only capable of inverting for velocity, but it is also capable of retrieving anisotropic parameters relying on linearized representations of the reflection response. To eliminate the cross-talk artifacts between different parameters, I

  9. Full cost accounting in the analysis of separated waste collection efficiency: A methodological proposal.

    Science.gov (United States)

    D'Onza, Giuseppe; Greco, Giulio; Allegrini, Marco

    2016-02-01

    Recycling implies additional costs for separated municipal solid waste (MSW) collection. The aim of the present study is to propose and implement a management tool - the full cost accounting (FCA) method - to calculate the full collection costs of different types of waste. Our analysis aims for a better understanding of the difficulties of putting FCA into practice in the MSW sector. We propose a FCA methodology that uses standard cost and actual quantities to calculate the collection costs of separate and undifferentiated waste. Our methodology allows cost efficiency analysis and benchmarking, overcoming problems related to firm-specific accounting choices, earnings management policies and purchase policies. Our methodology allows benchmarking and variance analysis that can be used to identify the causes of off-standards performance and guide managers to deploy resources more efficiently. Our methodology can be implemented by companies lacking a sophisticated management accounting system. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. A Proposed Method for Solving Fuzzy System of Linear Equations

    Directory of Open Access Journals (Sweden)

    Reza Kargar

    2014-01-01

    Full Text Available This paper proposes a new method for solving fuzzy system of linear equations with crisp coefficients matrix and fuzzy or interval right hand side. Some conditions for the existence of a fuzzy or interval solution of m×n linear system are derived and also a practical algorithm is introduced in detail. The method is based on linear programming problem. Finally the applicability of the proposed method is illustrated by some numerical examples.

  11. A Systematic Method to Synthesize New Transformerless Full-bridge Grid-tied Inverters

    DEFF Research Database (Denmark)

    Wang, Hongliang; Burton, Sarah; Liu, Yan-Fei

    2014-01-01

    Many inverter topologies have been proposed to eliminate the leakage current of transformerless Full Bridge Grid-Tied photovoltaic (PV) inverters. These include implementations such as the H5, H6, and HERIC topologies, among others. In this paper, a new full bridge topology synthesis method, called...... the MN synthesis method, is proposed. The MN method introduces two criteria that can be used to synthesize all of the possible topologies, including the existing topologies as well as new simplified topologies. This method concludes that there are only 15 simplified topologies available. Most simplified...... topologies from MN method have been verified by existing papers and patents....

  12. Impact of Costing and Cost Analysis Methods on the Result of the Period: Methods Based on Full Cost Theory

    Directory of Open Access Journals (Sweden)

    Toma Maria

    2017-01-01

    In light of the above, in the present paper we have proposed that objectives, to approach the methods of calculating full costs (economic or traditional, and comparing them to determine the effect they have on the outcome of the period.

  13. An automated full-symmetry Patterson search method

    International Nuclear Information System (INIS)

    Rius, J.; Miravitlles, C.

    1987-01-01

    A full-symmetry Patterson search method is presented that performs a molecular coarse rotation search in vector space and orientation refinement using the σ function. The oriented molecule is positioned using the fast translation function τ 0 , which is based on the automated interpretation of τ projections using the sum function. This strategy reduces the number of Patterson-function values to be stored in the rotation search, and the use of the τ 0 function minimizes the required time for the development of all probable rotation search solutions. The application of this method to five representative test examples is shown. (orig.)

  14. Full surface inspection methods regarding reinforcement corrosion of concrete structures

    International Nuclear Information System (INIS)

    Reichling, K.; Raupach, M.; Broomfield, J.; Gulikers, J.; L'Hostis, Valerie

    2013-01-01

    For reinforced concrete structures a localisation of all significant critical areas can only be done by a full surface inspection. The economic advantages are obvious: uncritical areas have not to be repaired expensively.The first step of the assessment should always be a visual inspection. The range of deterioration causes can be limited and the degree of deterioration may be estimated roughly. The inspection program can be adjusted to the requirements. By means of a full surface potential mapping areas with a high risk for chloride induced reinforcement corrosion can be localised, although no deteriorations are visually detectable at the concrete surface. In combination with concrete cover depth and resistivity measurements areas with corrosion promoting exposure conditions can be localised even if the reinforcement is not yet de-passivated. The following publication gives an overview about the essential full surface investigation methods to localise critical areas regarding corrosion of steel in concrete. The selection of methods is based on the inspection procedure given in reference 2. (authors)

  15. Extended discrete-ordinate method considering full polarization state

    International Nuclear Information System (INIS)

    Box, Michael A.; Qin Yi

    2006-01-01

    This paper presents an extension to the standard discrete-ordinate method (DOM) to consider generalized sources including: beam sources which can be placed at any (vertical) position and illuminate in any direction, thermal emission from the atmosphere and angularly distributed sources which illuminate from a surface as continuous functions of zenith and azimuth angles. As special cases, the thermal emission from the surface and deep space can be implemented as angularly distributed sources. Analytical-particular solutions for all source types are derived using the infinite medium Green's function. Radiation field zenith angle interpolation using source function integration is developed for all source types. The development considers the full state of polarization, including the sources (as applicable) and the (BRDF) surface, but the development can be reduced easily to scalar problems and is ready to be implemented in a single set of code for both scalar and vector radiative transfer computation

  16. Extended discrete-ordinate method considering full polarization state

    Energy Technology Data Exchange (ETDEWEB)

    Box, Michael A. [School of Physics, University of New South Wales (Australia)]. E-mail: m.box@unsw.edu.au; Qin Yi [School of Physics, University of New South Wales (Australia)]. E-mail: yi.qin@csiro.au

    2006-01-15

    This paper presents an extension to the standard discrete-ordinate method (DOM) to consider generalized sources including: beam sources which can be placed at any (vertical) position and illuminate in any direction, thermal emission from the atmosphere and angularly distributed sources which illuminate from a surface as continuous functions of zenith and azimuth angles. As special cases, the thermal emission from the surface and deep space can be implemented as angularly distributed sources. Analytical-particular solutions for all source types are derived using the infinite medium Green's function. Radiation field zenith angle interpolation using source function integration is developed for all source types. The development considers the full state of polarization, including the sources (as applicable) and the (BRDF) surface, but the development can be reduced easily to scalar problems and is ready to be implemented in a single set of code for both scalar and vector radiative transfer computation.

  17. Validation study of core analysis methods for full MOX BWR

    International Nuclear Information System (INIS)

    2013-01-01

    JNES has been developing a technical database used in reviewing validation of core analysis methods of LWRs in the coming occasions: (1) confirming the core safety parameters of the initial core (one-third MOX core) through a full MOX core in Oma Nuclear Power Plant, which is under the construction, (2) licensing high-burnup MOX cores in the future and (3) reviewing topical reports on core analysis codes for safety design and evaluation. Based on the technical database, JNES will issue a guide of reviewing the core analysis methods used for safety design and evaluation of LWRs. The database will be also used for validation and improving of core analysis codes developed by JNES. JNES has progressed with the projects: (1) improving a Doppler reactivity analysis model in a Monte Carlo calculation code MVP, (2) sensitivity study of nuclear cross section date on reactivity calculation of experimental cores composed of UO 2 and MOX fuel rods, (3) analysis of isotopic composition data for UO 2 and MOX fuels and (4) the guide of reviewing the core analysis codes and others. (author)

  18. Validation study of core analysis methods for full MOX BWR

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-15

    JNES has been developing a technical database used in reviewing validation of core analysis methods of LWRs in the coming occasions: (1) confirming the core safety parameters of the initial core (one-third MOX core) through a full MOX core in Oma Nuclear Power Plant, which is under the construction, (2) licensing high-burnup MOX cores in the future and (3) reviewing topical reports on core analysis codes for safety design and evaluation. Based on the technical database, JNES will issue a guide of reviewing the core analysis methods used for safety design and evaluation of LWRs. The database will be also used for validation and improving of core analysis codes developed by JNES. JNES has progressed with the projects: (1) improving a Doppler reactivity analysis model in a Monte Carlo calculation code MVP, (2) sensitivity study of nuclear cross section date on reactivity calculation of experimental cores composed of UO{sub 2} and MOX fuel rods, (3) analysis of isotopic composition data for UO{sub 2} and MOX fuels and (4) the guide of reviewing the core analysis codes and others. (author)

  19. A full digital approach to the TDCR method

    International Nuclear Information System (INIS)

    Mini, Giuliano; Pepe, Francesco; Tintori, Carlo; Capogni, Marco

    2014-01-01

    Current state of the art solutions based on the Triple to Double Coincidence Ratio method are generally large size, heavy-weight and not transportable systems. This is due, on one side, to large detectors and scintillation chambers and, on the other, to bulky analog electronics for data acquisition. CAEN developed a new, full digital approach to TDCR technique based on a portable, stand-alone, high-speed multichannel digitizer, on-board Digital Pulse Processing and dedicated DAQ software that emulates the well-known MAC3 analog board. - Highlights: • CAEN Desktop Digitizers used to emulate the MAC3 analog board in TDCR acquisition. • Spectroscopic application of the CAEN digitizers to the TDCR for charge spectra. • Development of two different softwares by CAEN and ENEA-INMRI for TDCR analysis. • Single electron peak obtained by CAEN digitizer and ENEA-INMRI portable TDCR. • Measurements of 90 Sr/ 90 Y by the new TDCR device equipped with CAEN digitizers

  20. Full Waveform Inversion Using Oriented Time Migration Method

    KAUST Repository

    Zhang, Zhendong

    2016-01-01

    Full waveform inversion (FWI) for reflection events is limited by its linearized update requirements given by a process equivalent to migration. Unless the background velocity model is reasonably accurate the resulting gradient can have

  1. The full size validation of remanent life assessment methods

    International Nuclear Information System (INIS)

    Hepworth, J.K.; Williams, J.A.

    1988-03-01

    A range of possible life assessment techniques for the remanent life appraisal of creeping structures is available in the published literature. However, due to the safety implications, the true conservatism of such methods cannot be assessed on operating plant. Consequently, the CEGB set up a four vessel programme in the Pressure Vessel Test Facility at the Marchwood Engineering Laboratories of the CEGB to underwrite and quantify the accuracy of these methods. The application of two non-destructive methods, namely strain monitoring and hardness measurement, to the data generated during about 12,000 hours of testing is examined. The current state of development of these methods is reviewed. Finally, the future CEGB programme relating to these vessels is discussed. (author)

  2. CLOPW; a mixed basis set full potential electronic structure method

    NARCIS (Netherlands)

    Bekker, H.G.; Bekker, Hermie Gerhard

    1997-01-01

    This thesis is about the development of the full potental CLOPW package for electronic structure calculations. Chapter 1 provides the necessary background in the theory of solid state physics. It gives a short overview of the effective one particle model as commonly used in solid state physics. It

  3. Proposed method for regulating major materials licensees

    International Nuclear Information System (INIS)

    1992-02-01

    The Director, Office of Nuclear Material Safety and Safeguards, US Nuclear Regulatory Commission, appointed a Materials Regulatory Review Task Force to conduct a broad-based review of the Commission's current licensing and oversight programs for fuel cycle and large materials plants. The task force, as requested, defined the components and subcomponents of an ideal regulatory evaluation system for these types of licensed plants and compared they to the components and subcomponents of the existing regulatory evaluation system. This report discusses findings from this comparison and proposed recommendations on the basis of these findings

  4. An AC Resistance Optimization Method Applicable for Inductor and Transformer Windings with Full Layers and Partial Layers

    DEFF Research Database (Denmark)

    Shen, Zhan; Li, Zhiguang; Jin, Long

    2017-01-01

    This paper proposes an ac resistance optimization method applicable for both inductor and transformer windings with full layers and partial layers. The proposed method treats the number of layers of the windings as a design variable instead of as a predefined parameter, compared to existing methods...

  5. A Denoising Method for LiDAR Full-Waveform Data

    Directory of Open Access Journals (Sweden)

    Xudong Lai

    2015-01-01

    Full Text Available Decomposition of LiDAR full-waveform data can not only enhance the density and positioning accuracy of a point cloud, but also provide other useful parameters, such as pulse width, peak amplitude, and peak position which are important information for subsequent processing. Full-waveform data usually contain some random noises. Traditional filtering algorithms always cause distortion in the waveform. λ/μ filtering algorithm is based on Mean Shift method. It can smooth the signal iteratively and will not cause any distortion in the waveform. In this paper, an improved λ/μ filtering algorithm is proposed, and several experiments on both simulated waveform data and real waveform data are implemented to prove the effectiveness of the proposed algorithm.

  6. 76 FR 20365 - Notice of Proposed Information Collection: Comment Request; Interstate Land Sales Full Disclosure...

    Science.gov (United States)

    2011-04-12

    ... Information Collection: Comment Request; Interstate Land Sales Full Disclosure Requirements AGENCY: Office of... Sales, Housing and Urban Development, 451 7th Street, SW., Washington, DC 20410, telephone (202) 708... techniques or other forms of information technology, e.g., permitting electronic submission of responses...

  7. One Curve Embedded Full-Bridge MMC Modeling Method with Detailed Representation of IGBT Characteristics

    Science.gov (United States)

    Hongyang, Yu; Zhengang, Lu; Xi, Yang

    2017-05-01

    Modular Multilevel Converter is more and more widely used in high voltage DC transmission system and high power motor drive system. It is a major topological structure for high power AC-DC converter. Due to the large module number, the complex control algorithm, and the high power user’s back ground, the MMC model used for simulation should be as accurate as possible to simulate the details of how MMC works for the dynamic testing of the MMC controller. But so far, there is no sample simulation MMC model which can simulate the switching dynamic process. In this paper, one curve embedded full-bridge MMC modeling method with detailed representation of IGBT characteristics is proposed. This method is based on the switching curve referring and sample circuit calculation, and it is sample for implementation. Based on the simulation comparison test under Matlab/Simulink, the proposed method is proved to be correct.

  8. A plastic collapse method for evaluating rotation capacity of full-restrained steel moment connections

    Directory of Open Access Journals (Sweden)

    Lee Kyungkoo

    2008-01-01

    Full Text Available An analytical method to model failure of steel beam plastic hinges due to local buckling and low-cycle fatigue is proposed herein. This method is based on the plastic collapse mechanism approach and a yield-line plastic hinge (YLPH model whose geometry is based on buckled shapes of beam plastic hinges observed in experiments. Two limit states, strength degradation failure induced by local buckling and low-cycle fatigue fracture, are considered. The proposed YLPH model was developed for FEMA-350 WUF-W, RBS and Free Flange connections and validated in comparisons to experimental data. This model can be used to estimate the seismic rotation capacity of fully restrained beam-column connections in special steel moment-resisting frames under both monotonic and cyclic loading conditions.

  9. A Shellcode Detection Method Based on Full Native API Sequence and Support Vector Machine

    Science.gov (United States)

    Cheng, Yixuan; Fan, Wenqing; Huang, Wei; An, Jing

    2017-09-01

    Dynamic monitoring the behavior of a program is widely used to discriminate between benign program and malware. It is usually based on the dynamic characteristics of a program, such as API call sequence or API call frequency to judge. The key innovation of this paper is to consider the full Native API sequence and use the support vector machine to detect the shellcode. We also use the Markov chain to extract and digitize Native API sequence features. Our experimental results show that the method proposed in this paper has high accuracy and low detection rate.

  10. Assessment of proposed electromagnetic quantum vacuum energy extraction methods

    OpenAIRE

    Moddel, Garret

    2009-01-01

    In research articles and patents several methods have been proposed for the extraction of zero-point energy from the vacuum. None has been reliably demonstrated, but the proposals remain largely unchallenged. In this paper the feasibility of these methods is assessed in terms of underlying thermodynamics principles of equilibrium, detailed balance, and conservation laws. The methods are separated into three classes: nonlinear processing of the zero-point field, mechanical extraction using Cas...

  11. Full-direct method for imaging pharmacokinetic parameters in dynamic fluorescence molecular tomography

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Guanglei, E-mail: guangleizhang@bjtu.edu.cn [Department of Biomedical Engineering, School of Medicine, Tsinghua University, Beijing 100084 (China); Department of Biomedical Engineering, School of Computer and Information Technology, Beijing Jiaotong University, Beijing 100044 (China); Pu, Huangsheng; Liu, Fei; Bai, Jing [Department of Biomedical Engineering, School of Medicine, Tsinghua University, Beijing 100084 (China); He, Wei [China Institute of Sport Science, Beijing 100061 (China); Luo, Jianwen, E-mail: luo-jianwen@tsinghua.edu.cn [Department of Biomedical Engineering, School of Medicine, Tsinghua University, Beijing 100084 (China); Center for Biomedical Imaging Research, School of Medicine, Tsinghua University, Beijing 100084 (China)

    2015-02-23

    Images of pharmacokinetic parameters (also known as parametric images) in dynamic fluorescence molecular tomography (FMT) can provide three-dimensional metabolic information for biological studies and drug development. However, the ill-posed nature of FMT and the high temporal variation of fluorophore concentration together make it difficult to obtain accurate parametric images in small animals in vivo. In this letter, we present a method to directly reconstruct the parametric images from the boundary measurements based on hybrid FMT/X-ray computed tomography (XCT) system. This method can not only utilize structural priors obtained from the XCT system to mitigate the ill-posedness of FMT but also make full use of the temporal correlations of boundary measurements to model the high temporal variation of fluorophore concentration. The results of numerical simulation and mouse experiment demonstrate that the proposed method leads to significant improvements in the reconstruction quality of parametric images.

  12. Full waveform inversion using oriented time-domain imaging method for vertical transverse isotropic media

    KAUST Repository

    Zhang, Zhendong

    2017-07-11

    Full waveform inversion for reection events is limited by its linearized update re-quirements given by a process equivalent to migration. Unless the background velocity model is reasonably accurate, the resulting gradient can have an inaccurate update direction leading the inversion to converge what we refer to as local minima of the objective function. In our approach, we consider mild lateral variation in the model, and thus, use a gradient given by the oriented time-domain imaging method. Specifically, we apply the oriented time-domain imaging on the data residual to obtain the geometrical features of the velocity perturbation. After updating the model in the time domain, we convert the perturbation from the time domain to depth using the average velocity. Considering density is constant, we can expand the conventional 1D impedance inversion method to 2D or 3D velocity inversion within the process of full waveform inversion. This method is not only capable of inverting for velocity, but it is also capable of retrieving anisotropic parameters relying on linearized representations of the reection response. To eliminate the cross-talk artifacts between different parameters, we utilize what we consider being an optimal parametrization for this step. To do so, we extend the prestack time-domain migration image in incident angle dimension to incorporate angular dependence needed by the multiparameter inversion. For simple models, this approach provides an efficient and stable way to do full waveform inversion or modified seismic inversion and makes the anisotropic inversion more practicable. The proposed method still needs kinematically accurate initial models since it only recovers the high-wavenumber part as conventional full waveform inversion method does. Results on synthetic data of isotropic and anisotropic cases illustrate the benefits and limitations of this method.

  13. A proposed assessment method for image of regional educational institutions

    Directory of Open Access Journals (Sweden)

    Kataeva Natalya

    2017-01-01

    Full Text Available Market of educational services in the current Russian economic conditions is a complex of a huge variety of educational institutions. Market of educational services is already experiencing a significant influence of the demographic situation in Russia. This means that higher education institutions are forced to fight in a tough competition for high school students. Increased competition in the educational market forces universities to find new methods of non-price competition in attraction of potential students and throughout own educational and economic activities. Commercialization of education places universities in a single plane with commercial companies who study a positive perception of the image and reputation as a competitive advantage, which is quite acceptable for use in strategic and current activities of higher education institutions to ensure the competitiveness of educational services and educational institution in whole. Nevertheless, due to lack of evidence-based proposals in this area there is a need for scientific research in terms of justification of organizational and methodological aspects of image use as a factor in the competitiveness of the higher education institution. Theoretically and practically there are different methods and ways of evaluating the company’s image. The article provides a comparative assessment of the existing valuation methods of corporate image and the author’s method of estimating the image of higher education institutions based on the key influencing factors. The method has been tested on the Vyatka State Agricultural Academy (Russia. The results also indicate the strengths and weaknesses of the institution, highlights ways of improving, and adjusts the efforts for image improvement.

  14. Proposal of Evolutionary Simplex Method for Global Optimization Problem

    Science.gov (United States)

    Shimizu, Yoshiaki

    To make an agile decision in a rational manner, role of optimization engineering has been notified increasingly under diversified customer demand. With this point of view, in this paper, we have proposed a new evolutionary method serving as an optimization technique in the paradigm of optimization engineering. The developed method has prospects to solve globally various complicated problem appearing in real world applications. It is evolved from the conventional method known as Nelder and Mead’s Simplex method by virtue of idea borrowed from recent meta-heuristic method such as PSO. Mentioning an algorithm to handle linear inequality constraints effectively, we have validated effectiveness of the proposed method through comparison with other methods using several benchmark problems.

  15. Full-band quantum simulation of electron devices with the pseudopotential method: Theory, implementation, and applications

    Science.gov (United States)

    Pala, M. G.; Esseni, D.

    2018-03-01

    This paper presents the theory, implementation, and application of a quantum transport modeling approach based on the nonequilibrium Green's function formalism and a full-band empirical pseudopotential Hamiltonian. We here propose to employ a hybrid real-space/plane-wave basis that results in a significant reduction of the computational complexity compared to a full plane-wave basis. To this purpose, we provide a theoretical formulation in the hybrid basis of the quantum confinement, the self-energies of the leads, and the coupling between the device and the leads. After discussing the theory and the implementation of the new simulation methodology, we report results for complete, self-consistent simulations of different electron devices, including a silicon Esaki diode, a thin-body silicon field effect transistor (FET), and a germanium tunnel FET. The simulated transistors have technologically relevant geometrical features with a semiconductor film thickness of about 4 nm and a channel length ranging from 10 to 17 nm. We believe that the newly proposed formalism may find applications also in transport models based on ab initio Hamiltonians, as those employed in density functional theory methods.

  16. Micro-seismic imaging using a source function independent full waveform inversion method

    Science.gov (United States)

    Wang, Hanchen; Alkhalifah, Tariq

    2018-03-01

    At the heart of micro-seismic event measurements is the task to estimate the location of the source micro-seismic events, as well as their ignition times. The accuracy of locating the sources is highly dependent on the velocity model. On the other hand, the conventional micro-seismic source locating methods require, in many cases manual picking of traveltime arrivals, which do not only lead to manual effort and human interaction, but also prone to errors. Using full waveform inversion (FWI) to locate and image micro-seismic events allows for an automatic process (free of picking) that utilizes the full wavefield. However, full waveform inversion of micro-seismic events faces incredible nonlinearity due to the unknown source locations (space) and functions (time). We developed a source function independent full waveform inversion of micro-seismic events to invert for the source image, source function and the velocity model. It is based on convolving reference traces with these observed and modeled to mitigate the effect of an unknown source ignition time. The adjoint-state method is used to derive the gradient for the source image, source function and velocity updates. The extended image for the source wavelet in Z axis is extracted to check the accuracy of the inverted source image and velocity model. Also, angle gathers is calculated to assess the quality of the long wavelength component of the velocity model. By inverting for the source image, source wavelet and the velocity model simultaneously, the proposed method produces good estimates of the source location, ignition time and the background velocity for synthetic examples used here, like those corresponding to the Marmousi model and the SEG/EAGE overthrust model.

  17. Micro-seismic imaging using a source function independent full waveform inversion method

    KAUST Repository

    Wang, Hanchen

    2018-03-26

    At the heart of micro-seismic event measurements is the task to estimate the location of the source micro-seismic events, as well as their ignition times. The accuracy of locating the sources is highly dependent on the velocity model. On the other hand, the conventional micro-seismic source locating methods require, in many cases manual picking of traveltime arrivals, which do not only lead to manual effort and human interaction, but also prone to errors. Using full waveform inversion (FWI) to locate and image micro-seismic events allows for an automatic process (free of picking) that utilizes the full wavefield. However, full waveform inversion of micro-seismic events faces incredible nonlinearity due to the unknown source locations (space) and functions (time). We developed a source function independent full waveform inversion of micro-seismic events to invert for the source image, source function and the velocity model. It is based on convolving reference traces with these observed and modeled to mitigate the effect of an unknown source ignition time. The adjoint-state method is used to derive the gradient for the source image, source function and velocity updates. The extended image for the source wavelet in Z axis is extracted to check the accuracy of the inverted source image and velocity model. Also, angle gathers is calculated to assess the quality of the long wavelength component of the velocity model. By inverting for the source image, source wavelet and the velocity model simultaneously, the proposed method produces good estimates of the source location, ignition time and the background velocity for synthetic examples used here, like those corresponding to the Marmousi model and the SEG/EAGE overthrust model.

  18. Principles, Methods of Participatory Research: Proposal for Draft Animal Power

    Directory of Open Access Journals (Sweden)

    E. Chia

    2004-03-01

    Full Text Available The meeting of researchers, who question themselves on the efficiency of their actions when they accompany stakeholders during change processes, provides the opportunity to ponder on the research methods to develop when working together with the stakeholders: participative research, research-action, research-intervention… The author proposes to present the research-action approach as new. If the three phases of research-action are important, the negotiation phase is essential, because it enables contract formalization among partners (ethical aspect, development of a common language, and formalization of structuring efforts between researchers with various specialties and stakeholders. In the research-action approach, the managing set-ups (scientific committees… play a major role: they guarantee at the same time a solution to problems, production, and the legitimacy of the scientific knowledge produced. In conclusion, the author suggests ways to develop research-action in the field of animal traction in order to conceive new socio-technical and organizational innovations that will make the use of this technique easier.

  19. Microseismic imaging using a source-independent full-waveform inversion method

    KAUST Repository

    Wang, Hanchen

    2016-09-06

    Using full waveform inversion (FWI) to locate microseismic and image microseismic events allows for an automatic process (free of picking) that utilizes the full wavefield. However, waveform inversion of microseismic events faces incredible nonlinearity due to the unknown source location (space) and function (time). We develop a source independent FWI of microseismic events to invert for the source image, source function and the velocity model. It is based on convolving reference traces with the observed and modeled data to mitigate the effect of an unknown source ignition time. The adjoint-state method is used to derive the gradient for the source image, source function and velocity updates. The extended image for source wavelet in z axis is extracted to check the accuracy of the inverted source image and velocity model. Also the angle gather is calculated to see if the velocity model is correct. By inverting for all the source image, source wavelet and the velocity model, the proposed method produces good estimates of the source location, ignition time and the background velocity for part of the SEG overthrust model.

  20. Microseismic imaging using a source-independent full-waveform inversion method

    KAUST Repository

    Wang, Hanchen

    2016-01-01

    Using full waveform inversion (FWI) to locate microseismic and image microseismic events allows for an automatic process (free of picking) that utilizes the full wavefield. However, waveform inversion of microseismic events faces incredible nonlinearity due to the unknown source location (space) and function (time). We develop a source independent FWI of microseismic events to invert for the source image, source function and the velocity model. It is based on convolving reference traces with the observed and modeled data to mitigate the effect of an unknown source ignition time. The adjoint-state method is used to derive the gradient for the source image, source function and velocity updates. The extended image for source wavelet in z axis is extracted to check the accuracy of the inverted source image and velocity model. Also the angle gather is calculated to see if the velocity model is correct. By inverting for all the source image, source wavelet and the velocity model, the proposed method produces good estimates of the source location, ignition time and the background velocity for part of the SEG overthrust model.

  1. A proposal of ITER vacuum vessel fabrication specification and results of the full-scale partial mock-up test

    Energy Technology Data Exchange (ETDEWEB)

    Nakahira, Masataka; Takeda, Nobukazu; Onozuka, Masanori [Japan Atomic Energy Agency (Japan); Kakudate, Satoshi [Mitsubishi Heavy Industries, Ltd. (Japan)

    2007-07-01

    The structure and fabrication methods of the ITER vacuum vessel have been investigated and defined by the ITER international team. However, some of the current specifications are very difficult to be achieved from the manufacturing point of view and will lead to cost increase. In the mock-up fabrication, it is planned to conduct the following items: 1. Feasibility of the Japanese proposed VV structure and fabrication methods and the applicability to the ITER are to be confirmed; 2. Assembly procedure and inspection procedure are to be confirmed; 3. Manufacturing tolerances are to be assessed; 4. Manufacturing schedule is to be assessed. This report summarizes the Japanese proposed specification of the VV mock-up describing differences between the ITER supplied design. General scope of the mock-up fabrication and the detailed dimensions are also shown. In the VV fabrication, several types of weld joint configuration will be used. This report shows the joint configurations proposed by Japan to be used for the inner shell connection, the rib-to-shell connection and outer shell connection, and the housing-to-shell connection, respectively. Non-destructive testing considered to be applied to each joint configuration is also presented. A series of the fabrication and assembly procedures for the mock-up are presented in this report, together with candidates of welding configurations. Finally, the report summarizes the results of mock-up fabrication, including results of nondestructive examination of weld lines, obtained welding deformation and issues revealed from the fabrication experience. (orig.)

  2. On the use of a penalized least squares method to process kinematic full-field measurements

    International Nuclear Information System (INIS)

    Moulart, Raphaël; Rotinat, René

    2014-01-01

    This work is aimed at exploring the performances of an alternative procedure to smooth and differentiate full-field displacement measurements. After recalling the strategies currently used by the experimental mechanics community, a short overview of the available smoothing algorithms is drawn up and the requirements that such an algorithm has to fulfil to be applicable to process kinematic measurements are listed. A comparative study of the chosen algorithm is performed including the 2D penalized least squares method and two other commonly implemented strategies. The results obtained by penalized least squares are comparable in terms of quality to those produced by the two other algorithms, while the penalized least squares method appears to be the fastest and the most flexible. Unlike both the other considered methods, it is possible with penalized least squares to automatically choose the parameter governing the amount of smoothing to apply. Unfortunately, it appears that this automation is not suitable for the proposed application since it does not lead to optimal strain maps. Finally, it is possible with this technique to perform the derivation to obtain strain maps before smoothing them (while the smoothing is normally applied to displacement maps before the differentiation), which can lead in some cases to a more effective reconstruction of the strain fields. (paper)

  3. Evaluation of a proposed optimization method for discrete-event simulation models

    Directory of Open Access Journals (Sweden)

    Alexandre Ferreira de Pinho

    2012-12-01

    Full Text Available Optimization methods combined with computer-based simulation have been utilized in a wide range of manufacturing applications. However, in terms of current technology, these methods exhibit low performance levels which are only able to manipulate a single decision variable at a time. Thus, the objective of this article is to evaluate a proposed optimization method for discrete-event simulation models based on genetic algorithms which exhibits more efficiency in relation to computational time when compared to software packages on the market. It should be emphasized that the variable's response quality will not be altered; that is, the proposed method will maintain the solutions' effectiveness. Thus, the study draws a comparison between the proposed method and that of a simulation instrument already available on the market and has been examined in academic literature. Conclusions are presented, confirming the proposed optimization method's efficiency.

  4. A novel full-field experimental method to measure the local compressibility of gas diffusion media

    Energy Technology Data Exchange (ETDEWEB)

    Lai, Yeh-Hung; Li, Yongqiang [Electrochemical Energy Research Lab, GM R and D, Honeoye Falls, NY 14472 (United States); Rock, Jeffrey A. [GM Powertrain, Honeoye Falls, NY 14472 (United States)

    2010-05-15

    The gas diffusion medium (GDM) in a proton exchange membrane (PEM) fuel cell needs to simultaneously satisfy the requirements of transporting reactant gases, removing product water, conducting electrons and heat, and providing mechanical support to the membrane electrode assembly (MEA). Concerning the localized over-compression which may force carbon fibers and other conductive debris into the membrane to cause fuel cell failure by electronically shorting through the membrane, we have developed a novel full-field experimental method to measure the local thickness and compressibility of GDM. Applying a uniform air pressure upon a thin polyimide film bonded on the top surface of the GDM with support from the bottom by a flat metal substrate and measuring the thickness change using the 3-D digital image correlation technique with an out-of-plane displacement resolution less than 0.5 {mu}m, we have determined the local thickness and compressive stress/strain behavior in the GDM. Using the local thickness and compressibility data over an area of 11.2 mm x 11.2 mm, we numerically construct the nominal compressive response of a commercial Toray trademark TGP-H-060 based GDM subjected to compression by flat platens. Good agreement in the nominal stress/strain curves from the numerical construction and direct experimental flat-platen measurement confirms the validity of the methodology proposed in this article. The result shows that a nominal pressure of 1.4 MPa compressed between two flat platens can introduce localized compressive stress concentration of more than 3 MPa in up to 1% of the total area at various locations from several hundred micrometers to 1 mm in diameter. We believe that this full-field experimental method can be useful in GDM material and process development to reduce the local hard spots and help to mitigate the membrane shorting failure in PEM fuel cells. (author)

  5. A novel full-field experimental method to measure the local compressibility of gas diffusion media

    Science.gov (United States)

    Lai, Yeh-Hung; Li, Yongqiang; Rock, Jeffrey A.

    The gas diffusion medium (GDM) in a proton exchange membrane (PEM) fuel cell needs to simultaneously satisfy the requirements of transporting reactant gases, removing product water, conducting electrons and heat, and providing mechanical support to the membrane electrode assembly (MEA). Concerning the localized over-compression which may force carbon fibers and other conductive debris into the membrane to cause fuel cell failure by electronically shorting through the membrane, we have developed a novel full-field experimental method to measure the local thickness and compressibility of GDM. Applying a uniform air pressure upon a thin polyimide film bonded on the top surface of the GDM with support from the bottom by a flat metal substrate and measuring the thickness change using the 3-D digital image correlation technique with an out-of-plane displacement resolution less than 0.5 μm, we have determined the local thickness and compressive stress/strain behavior in the GDM. Using the local thickness and compressibility data over an area of 11.2 mm × 11.2 mm, we numerically construct the nominal compressive response of a commercial Toray™ TGP-H-060 based GDM subjected to compression by flat platens. Good agreement in the nominal stress/strain curves from the numerical construction and direct experimental flat-platen measurement confirms the validity of the methodology proposed in this article. The result shows that a nominal pressure of 1.4 MPa compressed between two flat platens can introduce localized compressive stress concentration of more than 3 MPa in up to 1% of the total area at various locations from several hundred micrometers to 1 mm in diameter. We believe that this full-field experimental method can be useful in GDM material and process development to reduce the local hard spots and help to mitigate the membrane shorting failure in PEM fuel cells.

  6. Single-Phase Full-Wave Rectifier as an Effective Example to Teach Normalization, Conduction Modes, and Circuit Analysis Methods

    Directory of Open Access Journals (Sweden)

    Predrag Pejovic

    2013-12-01

    Full Text Available Application of a single phase rectifier as an example in teaching circuit modeling, normalization, operating modes of nonlinear circuits, and circuit analysis methods is proposed.The rectifier supplied from a voltage source by an inductive impedance is analyzed in the discontinuous as well as in the continuous conduction mode. Completely analytical solution for the continuous conduction mode is derived. Appropriate numerical methods are proposed to obtain the circuit waveforms in both of the operating modes, and to compute the performance parameters. Source code of the program that performs such computation is provided.

  7. Methodological proposal for environmental impact evaluation since different specific methods

    International Nuclear Information System (INIS)

    Leon Pelaez, Juan Diego; Lopera Arango Gabriel Jaime

    1999-01-01

    Some conceptual and practical elements related to environmental impact evaluation are described and related to the preparation of technical reports (environmental impact studies and environmental management plans) to be presented to environmental authorities for obtaining the environmental permits for development projects. In the first part of the document a summary of the main aspects of normative type is made that support the studies of environmental impact in Colombia. We propose a diagram for boarding and elaboration of the evaluation of environmental impact, which begins with the description of the project and of the environmental conditions in the area of the same. Passing then to identify the impacts through a method matricial and continuing with the quantitative evaluation of the same. For which we propose the use of the method developed by Arboleda (1994). Also we propose to qualify the activities of the project and the components of the environment in their relative importance, by means of a method here denominated agglomerate evaluation. Which allows finding those activities more impacting and the mostly impacted components. Lastly it is presented some models for the elaboration and presentation of the environmental management plans. The pursuit programs and those of environmental supervision

  8. A proposal of ITER vacuum vessel fabrication specification and results of the full-scale partial mock-up test

    International Nuclear Information System (INIS)

    Nakahira, M.; Takeda, N.; Kakudate, S.; Onozuka, M.

    2008-01-01

    The structure and fabrication methods of the ITER vacuum vessel (VV) have been investigated and defined by the ITER International Team (IT). However, some of the current technical specifications are difficult to be achieved from the manufacturing point of view. To solve such an issue, this paper proposes an alternative specification of the VV to the IT's design. A series of the fabrication and assembly procedures for the mock-up are presented, together with candidates of welding configurations. Finally, the paper summarizes the results of mock-up fabrication, such as non-destructive examination of weld lines, obtained welding deformation and issues revealed from the fabrication experience. Based on the results, it is suggested that several issues such as clarification of conditions of repair welding, demonstration of welding distortion control and detectability/localization of internal defects should be solved before manufacturing the ITER VV

  9. A proposal of ITER vacuum vessel fabrication specification and results of the full-scale partial mock-up test

    Energy Technology Data Exchange (ETDEWEB)

    Nakahira, M. [Japan Atomic Energy Agency, Mukouyama 801-1, Naka-machi, Naka-gun, Ibaraki 311-0193 (Japan)], E-mail: nakahira.masataka@jaea.go.jp; Takeda, N.; Kakudate, S. [Japan Atomic Energy Agency, Mukouyama 801-1, Naka-machi, Naka-gun, Ibaraki 311-0193 (Japan); Onozuka, M. [Mitsubishi Nuclear Energy Systems, Inc., 1700K Street NW, Suite 440, Washington, DC 20006 (United States)

    2008-12-15

    The structure and fabrication methods of the ITER vacuum vessel (VV) have been investigated and defined by the ITER International Team (IT). However, some of the current technical specifications are difficult to be achieved from the manufacturing point of view. To solve such an issue, this paper proposes an alternative specification of the VV to the IT's design. A series of the fabrication and assembly procedures for the mock-up are presented, together with candidates of welding configurations. Finally, the paper summarizes the results of mock-up fabrication, such as non-destructive examination of weld lines, obtained welding deformation and issues revealed from the fabrication experience. Based on the results, it is suggested that several issues such as clarification of conditions of repair welding, demonstration of welding distortion control and detectability/localization of internal defects should be solved before manufacturing the ITER VV.

  10. Assessment of uncertainty in full core reactor physics calculations using statistical methods

    International Nuclear Information System (INIS)

    McEwan, C.

    2012-01-01

    The best estimate method of safety analysis involves choosing a realistic set of input parameters for a proposed safety case and evaluating the uncertainty in the results. Determining the uncertainty in code outputs remains a challenge and is the subject of a benchmarking exercise proposed by the Organization for Economic Cooperation and Development. The work proposed in this paper will contribute to this benchmark by assessing the uncertainty in a depletion calculation of the final nuclide concentrations for an experiment performed in the Fukushima-2 reactor. This will be done using lattice transport code DRAGON and a tool known as DINOSAUR. (author)

  11. Assessment of uncertainty in full core reactor physics calculations using statistical methods

    Energy Technology Data Exchange (ETDEWEB)

    McEwan, C., E-mail: mcewac2@mcmaster.ca [McMaster Univ., Hamilton, Ontario (Canada)

    2012-07-01

    The best estimate method of safety analysis involves choosing a realistic set of input parameters for a proposed safety case and evaluating the uncertainty in the results. Determining the uncertainty in code outputs remains a challenge and is the subject of a benchmarking exercise proposed by the Organization for Economic Cooperation and Development. The work proposed in this paper will contribute to this benchmark by assessing the uncertainty in a depletion calculation of the final nuclide concentrations for an experiment performed in the Fukushima-2 reactor. This will be done using lattice transport code DRAGON and a tool known as DINOSAUR. (author)

  12. Full waveform seismic AVAZ signatures of anisotropic shales by integrated rock physics and the reflectivity method

    Science.gov (United States)

    Liu, Xiwu; Guo, Zhiqi; Han, Xu

    2018-06-01

    A set of parallel vertical fractures embedded in a vertically transverse isotropy (VTI) background leads to orthorhombic anisotropy and corresponding azimuthal seismic responses. We conducted seismic modeling of full waveform amplitude variations versus azimuth (AVAZ) responses of anisotropic shale by integrating a rock physics model and a reflectivity method. The results indicate that the azimuthal variation of P-wave velocity tends to be more complicated for orthorhombic medium compared to the horizontally transverse isotropy (HTI) case, especially at high polar angles. Correspondingly, for the HTI layer in the theoretical model, the short axis of the azimuthal PP amplitudes at the top interface is parallel to the fracture strike, while the long axis at the bottom reflection directs the fracture strike. In contrast, the orthorhombic layer in the theoretical model shows distinct AVAZ responses in terms of PP reflections. Nevertheless, the azimuthal signatures of the R- and T-components of the mode-converted PS reflections show similar AVAZ features for the HTI and orthorhombic layers, which may imply that the PS responses are dominated by fractures. For the application to real data, a seismic-well tie based on upscaled data and a reflectivity method illustrate good agreement between the reference layers and the corresponding reflected events. Finally, the full waveform seismic AVAZ responses of the Longmaxi shale formation are computed for the cases of HTI and orthorhombic anisotropy for comparison. For the two cases, the azimuthal features represent differences mainly in amplitudes, while slightly in the phases of the reflected waveforms. Azimuth variations in the PP reflections from the reference layers show distinct behaviors for the HTI and orthorhombic cases, while the mode-converted PS reflections in terms of the R- and T-components show little differences in azimuthal features. It may suggest that the behaviors of the PS waves are dominated by vertically

  13. Proposed frustrated-total-reflection acoustic sensing method

    International Nuclear Information System (INIS)

    Hull, J.R.

    1981-01-01

    Modulation of electromagnetic energy transmission through a frustrated-total-reflection device by pressure-induced changes in the index of refraction is proposed for use as an acoustic detector. Maximum sensitivity occurs for angles of incidence near the critical angle. The minimum detectable pressure in air is limited by Brownian noise. Acoustic propagation losses and diffraction of the optical beam by the acoustic signal limit the minimum acoustic wavelength to lengths of the order of the spatial extent of the optical beam. The response time of the method is fast enough to follow individual acoustic waves

  14. Micro-seismic imaging using a source function independent full waveform inversion method

    KAUST Repository

    Wang, Hanchen; Alkhalifah, Tariq Ali

    2018-01-01

    hand, the conventional micro-seismic source locating methods require, in many cases manual picking of traveltime arrivals, which do not only lead to manual effort and human interaction, but also prone to errors. Using full waveform inversion (FWI

  15. Modal loss mechanism of micro-structured VCSELs studied using full vector FDTD method.

    Science.gov (United States)

    Jo, Du-Ho; Vu, Ngoc Hai; Kim, Jin-Tae; Hwang, In-Kag

    2011-09-12

    Modal properties of vertical cavity surface-emitting lasers (VCSELs) with holey structures are studied using a finite difference time domain (FDTD) method. We investigate loss behavior with respect to the variation of structural parameters, and explain the loss mechanism of VCSELs. We also propose an effective method to estimate the modal loss based on mode profiles obtained using FDTD simulation. Our results could provide an important guideline for optimization of the microstructures of high-power single-mode VCSELs.

  16. The Virtual Fields Method Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements

    CERN Document Server

    Pierron, Fabrice

    2012-01-01

    The Virtual Fields Method: Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements is the first book on the Virtual Fields Method (VFM), a technique to identify materials mechanical properties from full-field measurements. Firmly rooted with extensive theoretical description of the method, the book presents numerous examples of application to a wide range of materials (composites, metals, welds, biomaterials) and situations (static, vibration, high strain rate). The authors give a detailed training section with examples of progressive difficulty to lead the reader to program the VFM and include a set of commented Matlab programs as well as GUI Matlab-based software for more general situations. The Virtual Fields Method: Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements is an ideal book for researchers, engineers, and students interested in applying the VFM to new situations motivated by their research.  

  17. Full Field and Anomaly Initialisation using a low order climate model: a comparison, and proposals for advanced formulations

    Science.gov (United States)

    Weber, Robin; Carrassi, Alberto; Guemas, Virginie; Doblas-Reyes, Francisco; Volpi, Danila

    2014-05-01

    Full Field (FFI) and Anomaly Initialisation (AI) are two schemes used to initialise seasonal-to-decadal (s2d) prediction. FFI initialises the model on the best estimate of the actual climate state and minimises the initial error. However, due to inevitable model deficiencies, the trajectories drift away from the observations towards the model's own attractor, inducing a bias in the forecast. AI has been devised to tackle the impact of drift through the addition of this bias onto the observations, in the hope of gaining an initial state closer to the model attractor. Its goal is to forecast climate anomalies. The large variety of experimental setups, global coupled models, and observational networks adopted world-wide have led to varying results with regards to the relative performance of AI and FFI. Our research is firstly motivated in a comparison of these two initialisation approaches under varying circumstances of observational errors, observational distributions, and model errors. We also propose and compare two advanced schemes for s2d prediction. Least Square Initialisation (LSI) intends to propagate observational information of partially initialized systems to the whole model domain, based on standard practices in data assimilation and using the covariance of the model anomalies. Exploring the Parameters Uncertainty (EPU) is an online drift correction technique applied during the forecast run after initialisation. It is designed to estimate, and subtract, the bias in the forecast related to parametric error. Experiments are carried out using an idealized coupled dynamics in order to facilitate better control and robust statistical inference. Results show that an improvement of FFI will necessitate refinements in the observations, whereas improvements in AI are subject to model advances. A successful approximation of the model attractor using AI is guaranteed only when the differences between model and nature probability distribution functions (PDFs) are

  18. Nouvelles méthodes d'identification des fractures par diagraphie acoustique en full wave form New Methods of Identifying Fractures by Full Wave Form Acoustic Logging

    Directory of Open Access Journals (Sweden)

    Denis A.

    2006-11-01

    Full Text Available Les outils acoustiques de dernière génération permettent maintenant d'enregistrer l'ensemble des ondes générées par une source acoustique à l'intérieur d'une géométrie cylindrique telle qu'un puits de sondage. Le train d'onde qu'il est alors possible d'analyser se compose successivement de trois composantes majeures (l'onde de compression, de cisaillement et de Stoneley dont nous avons une représentation pour chaque position de la sonde à l'intérieur du puits. Nous présentons, dans ce texte, trois méthodes originales et rapides (calculs possibles sur le site même pour identifier, à partir du traitement de l'onde de Stoneley, les fractures ouvertes recoupées par un forage. Nous donnons, dans un premier temps, nos motivations pour le choix unique du traitement de l'onde de Stoneley pour, dans un deuxième temps, exposer les trois méthodes développées et montrer pour chacune d'entre elles une application pratique. Interest in recognizing and identifying fractures in a coherent formation for the petroleum, geothermal and storage (oil and gas, wastes sectors has led to the development of indirect prospection methods inside boreholes such as acoustic logging. The latest acoustic tools are capable of recording all waves generated by an acoustic logging tool inside a cyclindrical geometry such as a borehole. The wavetrain that can then be analyzed is successively made up of three major components (the P compression wave, the S shear wave and the Stoneley wave for which we have a representation for each position of the logging tool in the borehole. An example of a recording is shown in Fig. 1. Because of its specific features (high amplitudes, low frequency, high signal-to-noise ratio, the Stoneley wave is recognized to be a good indicator of open fractures. Therefore, we use simple digital processing to quantify the influence of fracturing on the propagation of the Stoneley wave. Three methods stemming from the digital processing of

  19. The essential theory of fast wave current drive with full wave method

    International Nuclear Information System (INIS)

    Liu Yan; Gong Xueyu; Yang Lei; Yin Chenyan; Yin Lan

    2007-01-01

    The full wave numerical method is developed for analyzing fast wave current drive in the range of ion cyclotron waves in tokamak plasmas, taking into account finite larmor radius effects and parallel dispersion. the physical model, the dispersion relation on the assumption of Finite Larmor Radius (FLR) effects and the form of full wave be used for computer simulation are developed. All of the work will contribute to further study of fast wave current drive. (authors)

  20. Centrifugal compressor shape modification using a proposed inverse design method

    International Nuclear Information System (INIS)

    Niliahmadabadi, Mahdi; Poursadegh, Farzad

    2013-01-01

    This paper is concerned with a quasi-3D design method for the radial and axial diffusers of a centrifugal compressor on the meridional plane. The method integrates a novel inverse design algorithm, called ball-spine algorithm (BSA), and a quasi-3D analysis code. The Euler equation is solved on the meridional plane for a numerical domain, of which unknown boundaries (hub and shroud) are iteratively modified under the BSA until a prescribed pressure distribution is reached. In BSA, unknown walls are composed of a set of virtual balls that move freely along specified directions called spines. The difference between target and current pressure distributions causes the flexible boundary to deform at each modification step. In validating the quasi-3D analysis code, a full 3D Navier-Stokes code is used to analyze the existing and designed compressors numerically. Comparison of the quasi-3D analysis results with full 3D analysis results shows viable agreement. The 3D numerical analysis of the current compressor shows a huge total pressure loss on the 90 .deg. bend between the radial and axial diffusers. Geometric modification of the meridional plane causes the efficiency to improve by about 10%.

  1. Centrifugal compressor shape modification using a proposed inverse design method

    Energy Technology Data Exchange (ETDEWEB)

    Niliahmadabadi, Mahdi [Isfahan University of Technology, Isfahan (Iran, Islamic Republic of); Poursadegh, Farzad [Sharif University of Technology, Tehran (Iran, Islamic Republic of)

    2013-03-15

    This paper is concerned with a quasi-3D design method for the radial and axial diffusers of a centrifugal compressor on the meridional plane. The method integrates a novel inverse design algorithm, called ball-spine algorithm (BSA), and a quasi-3D analysis code. The Euler equation is solved on the meridional plane for a numerical domain, of which unknown boundaries (hub and shroud) are iteratively modified under the BSA until a prescribed pressure distribution is reached. In BSA, unknown walls are composed of a set of virtual balls that move freely along specified directions called spines. The difference between target and current pressure distributions causes the flexible boundary to deform at each modification step. In validating the quasi-3D analysis code, a full 3D Navier-Stokes code is used to analyze the existing and designed compressors numerically. Comparison of the quasi-3D analysis results with full 3D analysis results shows viable agreement. The 3D numerical analysis of the current compressor shows a huge total pressure loss on the 90 .deg. bend between the radial and axial diffusers. Geometric modification of the meridional plane causes the efficiency to improve by about 10%.

  2. A qualitative method proposal to improve environmental impact assessment

    Energy Technology Data Exchange (ETDEWEB)

    Toro, Javier, E-mail: jjtoroca@unal.edu.co [Institute of Environmental Studies, National University of Colombia at Bogotá (Colombia); Requena, Ignacio, E-mail: requena@decsai.ugr.es [Department of Computer Science and Artificial Intelligence, University of Granada (Spain); Duarte, Oscar, E-mail: ogduartev@unal.edu.co [National University of Colombia at Bogotá, Department of Electrical Engineering and Electronics (Colombia); Zamorano, Montserrat, E-mail: zamorano@ugr.es [Department of Civil Engineering, University of Granada (Spain)

    2013-11-15

    In environmental impact assessment, qualitative methods are used because they are versatile and easy to apply. This methodology is based on the evaluation of the strength of the impact by grading a series of qualitative attributes that can be manipulated by the evaluator. The results thus obtained are not objective, and all too often impacts are eliminated that should be mitigated with corrective measures. However, qualitative methodology can be improved if the calculation of Impact Importance is based on the characteristics of environmental factors and project activities instead on indicators assessed by evaluators. In this sense, this paper proposes the inclusion of the vulnerability of environmental factors and the potential environmental impact of project activities. For this purpose, the study described in this paper defined Total Impact Importance and specified a quantification procedure. The results obtained in the case study of oil drilling in Colombia reflect greater objectivity in the evaluation of impacts as well as a positive correlation between impact values, the environmental characteristics at and near the project location, and the technical characteristics of project activities. -- Highlights: • Concept of vulnerability has been used to calculate the importance impact assessment. • This paper defined Total Impact Importance and specified a quantification procedure. • The method includes the characteristics of environmental and project activities. • The application has shown greater objectivity in the evaluation of impacts. • Better correlation between impact values, environment and the project has been shown.

  3. A qualitative method proposal to improve environmental impact assessment

    International Nuclear Information System (INIS)

    Toro, Javier; Requena, Ignacio; Duarte, Oscar; Zamorano, Montserrat

    2013-01-01

    In environmental impact assessment, qualitative methods are used because they are versatile and easy to apply. This methodology is based on the evaluation of the strength of the impact by grading a series of qualitative attributes that can be manipulated by the evaluator. The results thus obtained are not objective, and all too often impacts are eliminated that should be mitigated with corrective measures. However, qualitative methodology can be improved if the calculation of Impact Importance is based on the characteristics of environmental factors and project activities instead on indicators assessed by evaluators. In this sense, this paper proposes the inclusion of the vulnerability of environmental factors and the potential environmental impact of project activities. For this purpose, the study described in this paper defined Total Impact Importance and specified a quantification procedure. The results obtained in the case study of oil drilling in Colombia reflect greater objectivity in the evaluation of impacts as well as a positive correlation between impact values, the environmental characteristics at and near the project location, and the technical characteristics of project activities. -- Highlights: • Concept of vulnerability has been used to calculate the importance impact assessment. • This paper defined Total Impact Importance and specified a quantification procedure. • The method includes the characteristics of environmental and project activities. • The application has shown greater objectivity in the evaluation of impacts. • Better correlation between impact values, environment and the project has been shown

  4. Optimal plot size in the evaluation of papaya scions: proposal and comparison of methods

    Directory of Open Access Journals (Sweden)

    Humberto Felipe Celanti

    Full Text Available ABSTRACT Evaluating the quality of scions is extremely important and it can be done by characteristics of shoots and roots. This experiment evaluated height of the aerial part, stem diameter, number of leaves, petiole length and length of roots of papaya seedlings. Analyses were performed from a blank trial with 240 seedlings of "Golden Pecíolo Curto". The determination of the optimum plot size was done by applying the methods of maximum curvature, maximum curvature of coefficient of variation and a new proposed method, which incorporates the bootstrap resampling simulation to the maximum curvature method. According to the results obtained, five is the optimal number of seedlings of papaya "Golden Pecíolo Curto" per plot. The proposed method of bootstrap simulation with replacement provides optimal plot sizes equal or higher than the maximum curvature method and provides same plot size than maximum curvature method of the coefficient of variation.

  5. Full-field and anomaly initialization using a low-order climate model: a comparison and proposals for advanced formulations

    Science.gov (United States)

    Carrassi, A.; Weber, R. J. T.; Guemas, V.; Doblas-Reyes, F. J.; Asif, M.; Volpi, D.

    2014-04-01

    Initialization techniques for seasonal-to-decadal climate predictions fall into two main categories; namely full-field initialization (FFI) and anomaly initialization (AI). In the FFI case the initial model state is replaced by the best possible available estimate of the real state. By doing so the initial error is efficiently reduced but, due to the unavoidable presence of model deficiencies, once the model is let free to run a prediction, its trajectory drifts away from the observations no matter how small the initial error is. This problem is partly overcome with AI where the aim is to forecast future anomalies by assimilating observed anomalies on an estimate of the model climate. The large variety of experimental setups, models and observational networks adopted worldwide make it difficult to draw firm conclusions on the respective advantages and drawbacks of FFI and AI, or to identify distinctive lines for improvement. The lack of a unified mathematical framework adds an additional difficulty toward the design of adequate initialization strategies that fit the desired forecast horizon, observational network and model at hand. Here we compare FFI and AI using a low-order climate model of nine ordinary differential equations and use the notation and concepts of data assimilation theory to highlight their error scaling properties. This analysis suggests better performances using FFI when a good observational network is available and reveals the direct relation of its skill with the observational accuracy. The skill of AI appears, however, mostly related to the model quality and clear increases of skill can only be expected in coincidence with model upgrades. We have compared FFI and AI in experiments in which either the full system or the atmosphere and ocean were independently initialized. In the former case FFI shows better and longer-lasting improvements, with skillful predictions until month 30. In the initialization of single compartments, the best

  6. Wide-angle full-vector beam propagation method based on an alternating direction implicit preconditioner

    Science.gov (United States)

    Chui, Siu Lit; Lu, Ya Yan

    2004-03-01

    Wide-angle full-vector beam propagation methods (BPMs) for three-dimensional wave-guiding structures can be derived on the basis of rational approximants of a square root operator or its exponential (i.e., the one-way propagator). While the less accurate BPM based on the slowly varying envelope approximation can be efficiently solved by the alternating direction implicit (ADI) method, the wide-angle variants involve linear systems that are more difficult to handle. We present an efficient solver for these linear systems that is based on a Krylov subspace method with an ADI preconditioner. The resulting wide-angle full-vector BPM is used to simulate the propagation of wave fields in a Y branch and a taper.

  7. Proposed Sandia frequency shift for anti-islanding detection method based on artificial immune system

    Directory of Open Access Journals (Sweden)

    A.Y. Hatata

    2018-03-01

    Full Text Available Sandia frequency shift (SFS is one of the active anti-islanding detection methods that depend on frequency drift to detect an islanding condition for inverter-based distributed generation. The non-detection zone (NDZ of the SFS method depends to a great extent on its parameters. Improper adjusting of these parameters may result in failure of the method. This paper presents a proposed artificial immune system (AIS-based technique to obtain optimal parameters of SFS anti-islanding detection method. The immune system is highly distributed, highly adaptive, and self-organizing in nature, maintains a memory of past encounters, and has the ability to continually learn about new encounters. The proposed method generates less total harmonic distortion (THD than the conventional SFS, which results in faster island detection and better non-detection zone. The performance of the proposed method is derived analytically and simulated using Matlab/Simulink. Two case studies are used to verify the proposed method. The first case includes a photovoltaic (PV connected to grid and the second includes a wind turbine connected to grid. The deduced optimized parameter setting helps to achieve the “non-islanding inverter” as well as least potential adverse impact on power quality. Keywords: Anti-islanding detection, Sandia frequency shift (SFS, Non-detection zone (NDZ, Total harmonic distortion (THD, Artificial immune system (AIS, Clonal selection algorithm

  8. Combined full field stress and strain measurement methods for granular materials

    Directory of Open Access Journals (Sweden)

    Broere W.

    2010-06-01

    Full Text Available The current paper re-introduces the photoelastic measurement method in experimental geomechanics. A full-field phase stepping polariscope suitable for geomechanical model tests has been developed. Additional constraints on the measurement and mechanical setup arising from geomechanical test conditions are outlined as well as the opportunity to measure the displacement fields in the sample with digital image correlation. The capability of the current setup in retrieving the stress and strain field in a granular material is demonstrated.

  9. Full quantitative phase analysis of hydrated lime using the Rietveld method

    International Nuclear Information System (INIS)

    Lassinantti Gualtieri, Magdalena; Romagnoli, Marcello; Miselli, Paola; Cannio, Maria; Gualtieri, Alessandro F.

    2012-01-01

    Full quantitative phase analysis (FQPA) using X-ray powder diffraction and Rietveld refinements is a well-established method for the characterization of various hydraulic binders such as Portland cement and hydraulic limes. In this paper, the Rietveld method is applied to hydrated lime, a non-hydraulic traditional binder. The potential presence of an amorphous phase in this material is generally ignored. Both synchrotron radiation and a conventional X-ray source were used for data collection. The applicability of the developed control file for the Rietveld refinements was investigated using samples spiked with glass. The results were cross-checked by other independent methods such as thermal and chemical analyses. The sample microstructure was observed by transmission electron microscopy. It was found that the consistency between the different methods was satisfactory, supporting the validity of FQPA for this material. For the samples studied in this work, the amount of amorphous material was in the range 2–15 wt.%.

  10. Full quantitative phase analysis of hydrated lime using the Rietveld method

    Energy Technology Data Exchange (ETDEWEB)

    Lassinantti Gualtieri, Magdalena, E-mail: magdalena.gualtieri@unimore.it [Dipartimento Ingegneria dei Materiali e dell' Ambiente, Universita Degli Studi di Modena e Reggio Emilia, Via Vignolese 905/a, I-41100 Modena (Italy); Romagnoli, Marcello; Miselli, Paola; Cannio, Maria [Dipartimento Ingegneria dei Materiali e dell' Ambiente, Universita Degli Studi di Modena e Reggio Emilia, Via Vignolese 905/a, I-41100 Modena (Italy); Gualtieri, Alessandro F. [Dipartimento di Scienze della Terra, Universita Degli Studi di Modena e Reggio Emilia, I-41100 Modena (Italy)

    2012-09-15

    Full quantitative phase analysis (FQPA) using X-ray powder diffraction and Rietveld refinements is a well-established method for the characterization of various hydraulic binders such as Portland cement and hydraulic limes. In this paper, the Rietveld method is applied to hydrated lime, a non-hydraulic traditional binder. The potential presence of an amorphous phase in this material is generally ignored. Both synchrotron radiation and a conventional X-ray source were used for data collection. The applicability of the developed control file for the Rietveld refinements was investigated using samples spiked with glass. The results were cross-checked by other independent methods such as thermal and chemical analyses. The sample microstructure was observed by transmission electron microscopy. It was found that the consistency between the different methods was satisfactory, supporting the validity of FQPA for this material. For the samples studied in this work, the amount of amorphous material was in the range 2-15 wt.%.

  11. An information preserving method for producing full coverage CoRoT light curves

    Directory of Open Access Journals (Sweden)

    Pascual-Granado J.

    2015-01-01

    Full Text Available Invalid flux measurements, caused mainly by the South Atlantic Anomaly crossing of the CoRoT satellite, introduce aliases in the periodogram and wrong amplitudes. It has been demonstrated that replacing such invalid data with a linear interpolation is not harmless. On the other side, using power spectrum estimators for unevenly sampled time series is not only less computationally efficient but it leads to difficulties in the interpretation of the results. Therefore, even when the gaps are rather small and the duty cycle is high enough the use of gap-filling methods is a gain in frequency analysis. However, the method must preserve the information contained in the time series. In this work we give a short description of an information preserving method (MIARMA and show some results when applying it to CoRoT seismo light curves. The method is implemented as the second step of a pipeline for CoRoT data analysis.

  12. Impact mitigation using kinematic constraints and the full space parameterization method

    Energy Technology Data Exchange (ETDEWEB)

    Morgansen, K.A.; Pin, F.G.

    1996-02-01

    A new method for mitigating unexpected impact of a redundant manipulator with an object in its environment is presented. Kinematic constraints are utilized with the recently developed method known as Full Space Parameterization (FSP). System performance criterion and constraints are changed at impact to return the end effector to the point of impact and halt the arm. Since large joint accelerations could occur as the manipulator is halted, joint acceleration bounds are imposed to simulate physical actuator limitations. Simulation results are presented for the case of a simple redundant planar manipulator.

  13. Laser induced ultrasonic phased array using full matrix capture data acquisition and total focusing method.

    Science.gov (United States)

    Stratoudaki, Theodosia; Clark, Matt; Wilcox, Paul D

    2016-09-19

    Laser ultrasonics is a technique where lasers are employed to generate and detect ultrasound. A data collection method (full matrix capture) and a post processing imaging algorithm, the total focusing method, both developed for ultrasonic arrays, are modified and used in order to enhance the capabilities of laser ultrasonics for nondestructive testing by improving defect detectability and increasing spatial resolution. In this way, a laser induced ultrasonic phased array is synthesized. A model is developed and compared with experimental results from aluminum samples with side drilled holes and slots at depths of 5 - 20 mm from the surface.

  14. Large Airborne Full Tensor Gradient Data Inversion Based on a Non-Monotone Gradient Method

    Science.gov (United States)

    Sun, Yong; Meng, Zhaohai; Li, Fengting

    2018-03-01

    Following the development of gravity gradiometer instrument technology, the full tensor gravity (FTG) data can be acquired on airborne and marine platforms. Large-scale geophysical data can be obtained using these methods, making such data sets a number of the "big data" category. Therefore, a fast and effective inversion method is developed to solve the large-scale FTG data inversion problem. Many algorithms are available to accelerate the FTG data inversion, such as conjugate gradient method. However, the conventional conjugate gradient method takes a long time to complete data processing. Thus, a fast and effective iterative algorithm is necessary to improve the utilization of FTG data. Generally, inversion processing is formulated by incorporating regularizing constraints, followed by the introduction of a non-monotone gradient-descent method to accelerate the convergence rate of FTG data inversion. Compared with the conventional gradient method, the steepest descent gradient algorithm, and the conjugate gradient algorithm, there are clear advantages of the non-monotone iterative gradient-descent algorithm. Simulated and field FTG data were applied to show the application value of this new fast inversion method.

  15. A computationally efficient method for full-core conjugate heat transfer modeling of sodium fast reactors

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Rui, E-mail: rhu@anl.gov; Yu, Yiqi

    2016-11-15

    Highlights: • Developed a computationally efficient method for full-core conjugate heat transfer modeling of sodium fast reactors. • Applied fully-coupled JFNK solution scheme to avoid the operator-splitting errors. • The accuracy and efficiency of the method is confirmed with a 7-assembly test problem. • The effects of different spatial discretization schemes are investigated and compared to the RANS-based CFD simulations. - Abstract: For efficient and accurate temperature predictions of sodium fast reactor structures, a 3-D full-core conjugate heat transfer modeling capability is developed for an advanced system analysis tool, SAM. The hexagon lattice core is modeled with 1-D parallel channels representing the subassembly flow, and 2-D duct walls and inter-assembly gaps. The six sides of the hexagon duct wall and near-wall coolant region are modeled separately to account for different temperatures and heat transfer between coolant flow and each side of the duct wall. The Jacobian Free Newton Krylov (JFNK) solution method is applied to solve the fluid and solid field simultaneously in a fully coupled fashion. The 3-D full-core conjugate heat transfer modeling capability in SAM has been demonstrated by a verification test problem with 7 fuel assemblies in a hexagon lattice layout. Additionally, the SAM simulation results are compared with RANS-based CFD simulations. Very good agreements have been achieved between the results of the two approaches.

  16. FIFRA Peer Review: Proposed Risk Assessment Methods Process

    Science.gov (United States)

    From September 11-14, 2012, EPA participated in a Federal Insecticide, Fungicide and Rodenticide Act Scientific Advisory Panel (SAP) meeting on a proposed pollinator risk assessment framework for determining the potential risks of pesticides to honey bees.

  17. The optimized gradient method for full waveform inversion and its spectral implementation

    KAUST Repository

    Wu, Zedong; Alkhalifah, Tariq Ali

    2016-01-01

    At the heart of the full waveform inversion (FWI) implementation is wavefield extrapolation, and specifically its accuracy and cost. To obtain accurate, dispersion free wavefields, the extrapolation for modelling is often expensive. Combining an efficient extrapolation with a novel gradient preconditioning can render an FWI implementation that efficiently converges to an accurate model. We, specifically, recast the extrapolation part of the inversion in terms of its spectral components for both data and gradient calculation. This admits dispersion free wavefields even at large extrapolation time steps, which improves the efficiency of the inversion. An alternative spectral representation of the depth axis in terms of sine functions allows us to impose a free surface boundary condition, which reflects our medium boundaries more accurately. Using a newly derived perfectly matched layer formulation for this spectral implementation, we can define a finite model with absorbing boundaries. In order to reduce the nonlinearity in FWI, we propose a multiscale conditioning of the objective function through combining the different directional components of the gradient to optimally update the velocity. Through solving a simple optimization problem, it specifically admits the smoothest approximate update while guaranteeing its ascending direction. An application to the Marmousi model demonstrates the capability of the proposed approach and justifies our assertions with respect to cost and convergence.

  18. The optimized gradient method for full waveform inversion and its spectral implementation

    KAUST Repository

    Wu, Zedong

    2016-03-28

    At the heart of the full waveform inversion (FWI) implementation is wavefield extrapolation, and specifically its accuracy and cost. To obtain accurate, dispersion free wavefields, the extrapolation for modelling is often expensive. Combining an efficient extrapolation with a novel gradient preconditioning can render an FWI implementation that efficiently converges to an accurate model. We, specifically, recast the extrapolation part of the inversion in terms of its spectral components for both data and gradient calculation. This admits dispersion free wavefields even at large extrapolation time steps, which improves the efficiency of the inversion. An alternative spectral representation of the depth axis in terms of sine functions allows us to impose a free surface boundary condition, which reflects our medium boundaries more accurately. Using a newly derived perfectly matched layer formulation for this spectral implementation, we can define a finite model with absorbing boundaries. In order to reduce the nonlinearity in FWI, we propose a multiscale conditioning of the objective function through combining the different directional components of the gradient to optimally update the velocity. Through solving a simple optimization problem, it specifically admits the smoothest approximate update while guaranteeing its ascending direction. An application to the Marmousi model demonstrates the capability of the proposed approach and justifies our assertions with respect to cost and convergence.

  19. Prediction of hyperbilirubinemia by noninvasive methods in full-term newborns

    Directory of Open Access Journals (Sweden)

    Danijela Furlan

    2013-02-01

    Full Text Available Introduction: The noninvasive screening methods for bilirubin determination were studied prospectively in a group of full-term healthy newborns with the aim of early prediction of pathological neonatal hyperbilirubinemia. Laboratory determination of bilirubin (Jendrassik-Grof (JG was compared to the noninvasive transcutaneous bilirubin (TcBIL together with the determination of bilirubin in cord blood.Methods: The study group consisted of 284 full-term healthy consecutively born infants in the period from March to June 2011. The whole group was divided into a group of physiological (n=199, and a group of pathological hyperbilirubinemia (n=85 according to the level of total bilirubin (220 μmol/L. Bilirubin in cord blood (CbBIL and from capillary blood at the age of three days was determined according to the JG, on the 3rd day TcBIL was also detected by Bilicheck bilirubinometer. The Kolmogorov-Smirnov and Mann-Whitney tests were used for the statistical analysis.Results: Bilirubin concentrations were statisti cally significantly different (CbBIL (p<0,001 on the 3rd day control sample (p<0,001, TcBil (p<0,001 between the groups of newborns with physiological (n=199 and pathological (n=85 hyperbilirubinemia. Using the cut-off value of cord blood bilirubin 28 μmol/L, we could predict the development of pathological hyperbiliru binemia with 98.8% prognostic specificity, and with 100% sensitivity that newborns will not require a phototherapy (all irradiated newborns were taken into account. We confirmed an excellent agreement between bilirubin concentrations determined by the TcBIL and JG methods for both groups of healthy full-term newborns.Conclusion: Based on our results, we could recommend that determination of the cord blood bilirubin in combination with the measurement of TcBIL should be implemented into practice for early prediction of pathological hyperbilirubinemia in full-term healthy newborns. The advantages of both methods in the routine

  20. A Critical Assessment of the Microorganisms Proposed to be Important to Enhanced Biological Phosphorus Removal in Full-Scale Wastewater Treatment Systems

    Directory of Open Access Journals (Sweden)

    Per H. Nielsen

    2017-04-01

    Full Text Available Understanding the microbiology of phosphorus (P removal is considered essential to knowledge-based optimization of enhanced biological P removal (EBPR systems. Biological P removal is achieved in these systems by promoting the growth of organisms collectively known as the polyphosphate accumulating organisms (PAOs. Also considered important to EBPR are the glycogen accumulating organisms (GAOs, which are theorized to compete with the PAOs for resources at the expense of P removal efficiency. Numerous studies have sought to identify the PAOs and their GAOs competitors, with several candidates proposed for each over the last few decades. The current study collectively assessed the abundance and diversity of all proposed PAOs and GAOs in 18 Danish full-scale wastewater treatment plants with well-working biological nutrient removal over a period of 9 years using 16S rRNA gene amplicon sequencing. The microbial community structure in all plants was relatively stable over time. Evidence for the role of the proposed PAOs and GAOs in EBPR varies and is critically assessed, in light of their calculated amplicon abundances, to indicate which of these are important in full-scale systems. Bacteria from the genus Tetrasphaera were the most abundant of the PAOs. The “Candidatus Accumulibacter” PAOs were in much lower abundance and appear to be biased by the amplicon-based method applied. The genera Dechloromonas, Microlunatus, and Tessaracoccus were identified as abundant putative PAO that require further research attention. Interestingly, the actinobacterial Micropruina and sbr-gs28 phylotypes were among the most abundant of the putative GAOs. Members of the genera Defluviicoccus, Propionivibrio, the family Competibacteraceae, and the spb280 group were also relatively abundant in some plants. Despite observed high abundances of GAOs (periodically exceeding 20% of the amplicon reads, P removal performance was maintained, indicating that these organisms

  1. An Online Full-Body Motion Recognition Method Using Sparse and Deficient Signal Sequences

    Directory of Open Access Journals (Sweden)

    Chengyu Guo

    2014-01-01

    Full Text Available This paper presents a method to recognize continuous full-body human motion online by using sparse, low-cost sensors. The only input signals needed are linear accelerations without any rotation information, which are provided by four Wiimote sensors attached to the four human limbs. Based on the fused hidden Markov model (FHMM and autoregressive process, a predictive fusion model (PFM is put forward, which considers the different influences of the upper and lower limbs, establishes HMM for each part, and fuses them using a probabilistic fusion model. Then an autoregressive process is introduced in HMM to predict the gesture, which enables the model to deal with incomplete signal data. In order to reduce the number of alternatives in the online recognition process, a graph model is built that rejects parts of motion types based on the graph structure and previous recognition results. Finally, an online signal segmentation method based on semantics information and PFM is presented to finish the efficient recognition task. The results indicate that the method is robust with a high recognition rate of sparse and deficient signals and can be used in various interactive applications.

  2. The hydrogen tunneling splitting in malonaldehyde: A full-dimensional time-independent quantum mechanical method

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Feng; Ren, Yinghui; Bian, Wensheng, E-mail: bian@iccas.ac.cn [Beijing National Laboratory for Molecular Sciences, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); University of Chinese Academy of Sciences, Beijing 100049 (China)

    2016-08-21

    The accurate time-independent quantum dynamics calculations on the ground-state tunneling splitting of malonaldehyde in full dimensionality are reported for the first time. This is achieved with an efficient method developed by us. In our method, the basis functions are customized for the hydrogen transfer process which has the effect of greatly reducing the size of the final Hamiltonian matrix, and the Lanczos method and parallel strategy are used to further overcome the memory and central processing unit time bottlenecks. The obtained ground-state tunneling splitting of 24.5 cm{sup −1} is in excellent agreement with the benchmark value of 23.8 cm{sup −1} computed with the full-dimensional, multi-configurational time-dependent Hartree approach on the same potential energy surface, and we estimate that our reported value has an uncertainty of less than 0.5 cm{sup −1}. Moreover, the role of various vibrational modes strongly coupled to the hydrogen transfer process is revealed.

  3. A deterministic alternative to the full configuration interaction quantum Monte Carlo method

    Energy Technology Data Exchange (ETDEWEB)

    Tubman, Norm M.; Lee, Joonho; Takeshita, Tyler Y.; Head-Gordon, Martin; Whaley, K. Birgitta [University of California, Berkeley, Berkeley, California 94720 (United States)

    2016-07-28

    Development of exponentially scaling methods has seen great progress in tackling larger systems than previously thought possible. One such technique, full configuration interaction quantum Monte Carlo, is a useful algorithm that allows exact diagonalization through stochastically sampling determinants. The method derives its utility from the information in the matrix elements of the Hamiltonian, along with a stochastic projected wave function, to find the important parts of Hilbert space. However, the stochastic representation of the wave function is not required to search Hilbert space efficiently, and here we describe a highly efficient deterministic method that can achieve chemical accuracy for a wide range of systems, including the difficult Cr{sub 2} molecule. We demonstrate for systems like Cr{sub 2} that such calculations can be performed in just a few cpu hours which makes it one of the most efficient and accurate methods that can attain chemical accuracy for strongly correlated systems. In addition our method also allows efficient calculation of excited state energies, which we illustrate with benchmark results for the excited states of C{sub 2}.

  4. Study on the Contra-Rotating Propeller system design and full-scale performance prediction method

    Directory of Open Access Journals (Sweden)

    Keh-Sik Min

    2009-09-01

    Full Text Available A ship's screw-propeller produces thrust by rotation and, at the same time, generates rotational flow behind the propeller. This rotational flow has no contribution to the generation of thrust, but instead produces energy loss. By recovering part of the lost energy in the rotational flow, therefore, it is possible to improve the propulsion efficiency. The contra-rotating propeller (CRP system is the representing example of such devices. Unfortunately, however, neither a design method nor a full-scale performance prediction procedure for the CRP system has been well established yet. The authors have long performed studies on the CRP system, and some of the results from the authors’ studies shall be presented and discussed.

  5. Kalman and particle filtering methods for full vehicle and tyre identification

    Science.gov (United States)

    Bogdanski, Karol; Best, Matthew C.

    2018-05-01

    This paper considers identification of all significant vehicle handling dynamics of a test vehicle, including identification of a combined-slip tyre model, using only those sensors currently available on most vehicle controller area network buses. Using an appropriately simple but efficient model structure, all of the independent parameters are found from test vehicle data, with the resulting model accuracy demonstrated on independent validation data. The paper extends previous work on augmented Kalman Filter state estimators to concentrate wholly on parameter identification. It also serves as a review of three alternative filtering methods; identifying forms of the unscented Kalman filter, extended Kalman filter and particle filter are proposed and compared for effectiveness, complexity and computational efficiency. All three filters are suited to applications of system identification and the Kalman Filters can also operate in real-time in on-line model predictive controllers or estimators.

  6. A new method for assessing the accuracy of full arch impressions in patients.

    Science.gov (United States)

    Kuhr, F; Schmidt, A; Rehmann, P; Wöstmann, B

    2016-12-01

    To evaluate a new method of measuring the real deviation (trueness) of full arch impressions intraorally and to investigate the trueness of digital full arch impressions in comparison to a conventional impression procedure in clinical use. Four metal spheres were fixed with composite using a metal application aid to the lower teeth of 50 test subjects as reference structures. One conventional impression (Impregum Penta Soft) with subsequent type-IV gypsum model casting (CI) and three different digital impressions were performed in the lower jaw of each test person with the following intraoral scanners: Sirona CEREC Omnicam (OC), 3M True Definition (TD), Heraeus Cara TRIOS (cT). The digital and conventional (gypsum) models were analyzed relative to the spheres. Linear distance and angle measurements between the spheres, as well as digital superimpositions of the spheres with the reference data set were executed. With regard to the distance measurements, CI showed the smallest deviations followed by intraoral scanners TD, cT and OC. A digital superimposition procedure yielded the same order for the outcomes: CI (15±4μm), TD (23±9μm), cT (37±14μm), OC (214±38μm). Angle measurements revealed the smallest deviation for TD (0.06°±0,07°) followed by CI (0.07°±0.07°), cT (0.13°±0.15°) and OC (0.28°±0.21°). The new measuring method is suitable for measuring the dimensional accuracy of full arch impressions intraorally. CI is still significantly more accurate than full arch scans with intraoral scanners in clinical use. Conventional full arch impressions with polyether impression materials are still more accurate than full arch digital impressions. Digital impression systems using powder application and active wavefront sampling technology achieve the most accurate results in comparison to other intraoral scanning systems (DRKS-ID: DRKS00009360, German Clinical Trials Register). Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Proposed efficient method for ticket booking (PEMTB) | Ahmed ...

    African Journals Online (AJOL)

    Journal of Fundamental and Applied Sciences. Journal Home ... We used angular JS, ionic for a front end and node.js, express.js for a back end and mongo DB for a database. ... Our proposed system is totally softcopy and in digitalized.

  8. FULL GPU Implementation of Lattice-Boltzmann Methods with Immersed Boundary Conditions for Fast Fluid Simulations

    Directory of Open Access Journals (Sweden)

    G Boroni

    2017-03-01

    Full Text Available Lattice Boltzmann Method (LBM has shown great potential in fluid simulations, but performance issues and difficulties to manage complex boundary conditions have hindered a wider application. The upcoming of Graphic Processing Units (GPU Computing offered a possible solution for the performance issue, and methods like the Immersed Boundary (IB algorithm proved to be a flexible solution to boundaries. Unfortunately, the implicit IB algorithm makes the LBM implementation in GPU a non-trivial task. This work presents a fully parallel GPU implementation of LBM in combination with IB. The fluid-boundary interaction is implemented via GPU kernels, using execution configurations and data structures specifically designed to accelerate each code execution. Simulations were validated against experimental and analytical data showing good agreement and improving the computational time. Substantial reductions of calculation rates were achieved, lowering down the required time to execute the same model in a CPU to about two magnitude orders.

  9. Full-waveform detection of non-impulsive seismic events based on time-reversal methods

    Science.gov (United States)

    Solano, Ericka Alinne; Hjörleifsdóttir, Vala; Liu, Qinya

    2017-12-01

    We present a full-waveform detection method for non-impulsive seismic events, based on time-reversal principles. We use the strain Green's tensor as a matched filter, correlating it with continuous observed seismograms, to detect non-impulsive seismic events. We show that this is mathematically equivalent to an adjoint method for detecting earthquakes. We define the detection function, a scalar valued function, which depends on the stacked correlations for a group of stations. Event detections are given by the times at which the amplitude of the detection function exceeds a given value relative to the noise level. The method can make use of the whole seismic waveform or any combination of time-windows with different filters. It is expected to have an advantage compared to traditional detection methods for events that do not produce energetic and impulsive P waves, for example glacial events, landslides, volcanic events and transform-fault earthquakes for events which velocity structure along the path is relatively well known. Furthermore, the method has advantages over empirical Greens functions template matching methods, as it does not depend on records from previously detected events, and therefore is not limited to events occurring in similar regions and with similar focal mechanisms as these events. The method is not specific to any particular way of calculating the synthetic seismograms, and therefore complicated structural models can be used. This is particularly beneficial for intermediate size events that are registered on regional networks, for which the effect of lateral structure on the waveforms can be significant. To demonstrate the feasibility of the method, we apply it to two different areas located along the mid-oceanic ridge system west of Mexico where non-impulsive events have been reported. The first study area is between Clipperton and Siqueiros transform faults (9°N), during the time of two earthquake swarms, occurring in March 2012 and May

  10. Full-sky formulae for weak lensing power spectra from total angular momentum method

    International Nuclear Information System (INIS)

    Yamauchi, Daisuke; Taruya, Atsushi; Namikawa, Toshiya

    2013-01-01

    We systematically derive full-sky formulae for the weak lensing power spectra generated by scalar, vector and tensor perturbations from the total angular momentum (TAM) method. Based on both the geodesic and geodesic deviation equations, we first give the gauge-invariant expressions for the deflection angle and Jacobi map as observables of the CMB lensing and cosmic shear experiments. We then apply the TAM method, originally developed in the theoretical studies of CMB, to a systematic derivation of the angular power spectra. The TAM representation, which characterizes the total angular dependence of the spatial modes projected along a line-of-sight, can carry all the information of the lensing modes generated by scalar, vector, and tensor metric perturbations. This greatly simplifies the calculation, and we present a complete set of the full-sky formulae for angular power spectra in both the E-/B-mode cosmic shear and gradient-/curl-mode lensing potential of deflection angle. Based on the formulae, we give illustrative examples of non-vanishing B-mode cosmic shear and curl-mode of deflection angle in the presence of the vector and tensor perturbations, and explicitly compute the power spectra

  11. Automatically classifying sentences in full-text biomedical articles into Introduction, Methods, Results and Discussion.

    Science.gov (United States)

    Agarwal, Shashank; Yu, Hong

    2009-12-01

    Biomedical texts can be typically represented by four rhetorical categories: Introduction, Methods, Results and Discussion (IMRAD). Classifying sentences into these categories can benefit many other text-mining tasks. Although many studies have applied different approaches for automatically classifying sentences in MEDLINE abstracts into the IMRAD categories, few have explored the classification of sentences that appear in full-text biomedical articles. We first evaluated whether sentences in full-text biomedical articles could be reliably annotated into the IMRAD format and then explored different approaches for automatically classifying these sentences into the IMRAD categories. Our results show an overall annotation agreement of 82.14% with a Kappa score of 0.756. The best classification system is a multinomial naïve Bayes classifier trained on manually annotated data that achieved 91.95% accuracy and an average F-score of 91.55%, which is significantly higher than baseline systems. A web version of this system is available online at-http://wood.ims.uwm.edu/full_text_classifier/.

  12. A Critical Assessment of the Microorganisms Proposed to be Important to Enhanced Biological Phosphorus Removal in Full-Scale Wastewater Treatment Systems.

    Science.gov (United States)

    Stokholm-Bjerregaard, Mikkel; McIlroy, Simon J; Nierychlo, Marta; Karst, Søren M; Albertsen, Mads; Nielsen, Per H

    2017-01-01

    Understanding the microbiology of phosphorus (P) removal is considered essential to knowledge-based optimization of enhanced biological P removal (EBPR) systems. Biological P removal is achieved in these systems by promoting the growth of organisms collectively known as the polyphosphate accumulating organisms (PAOs). Also considered important to EBPR are the glycogen accumulating organisms (GAOs), which are theorized to compete with the PAOs for resources at the expense of P removal efficiency. Numerous studies have sought to identify the PAOs and their GAOs competitors, with several candidates proposed for each over the last few decades. The current study collectively assessed the abundance and diversity of all proposed PAOs and GAOs in 18 Danish full-scale wastewater treatment plants with well-working biological nutrient removal over a period of 9 years using 16S rRNA gene amplicon sequencing. The microbial community structure in all plants was relatively stable over time. Evidence for the role of the proposed PAOs and GAOs in EBPR varies and is critically assessed, in light of their calculated amplicon abundances, to indicate which of these are important in full-scale systems. Bacteria from the genus Tetrasphaera were the most abundant of the PAOs. The " Candidatus Accumulibacter" PAOs were in much lower abundance and appear to be biased by the amplicon-based method applied. The genera Dechloromonas, Microlunatus , and Tessaracoccus were identified as abundant putative PAO that require further research attention. Interestingly, the actinobacterial Micropruina and sbr-gs28 phylotypes were among the most abundant of the putative GAOs. Members of the genera Defluviicoccus, Propionivibrio , the family Competibacteraceae, and the spb280 group were also relatively abundant in some plants. Despite observed high abundances of GAOs (periodically exceeding 20% of the amplicon reads), P removal performance was maintained, indicating that these organisms were not

  13. Improvement of resolution in full-view linear-array photoacoustic computed tomography using a novel adaptive weighting method

    Science.gov (United States)

    Omidi, Parsa; Diop, Mamadou; Carson, Jeffrey; Nasiriavanaki, Mohammadreza

    2017-03-01

    Linear-array-based photoacoustic computed tomography is a popular methodology for deep and high resolution imaging. However, issues such as phase aberration, side-lobe effects, and propagation limitations deteriorate the resolution. The effect of phase aberration due to acoustic attenuation and constant assumption of the speed of sound (SoS) can be reduced by applying an adaptive weighting method such as the coherence factor (CF). Utilizing an adaptive beamforming algorithm such as the minimum variance (MV) can improve the resolution at the focal point by eliminating the side-lobes. Moreover, invisibility of directional objects emitting parallel to the detection plane, such as vessels and other absorbing structures stretched in the direction perpendicular to the detection plane can degrade resolution. In this study, we propose a full-view array level weighting algorithm in which different weighs are assigned to different positions of the linear array based on an orientation algorithm which uses the histogram of oriented gradient (HOG). Simulation results obtained from a synthetic phantom show the superior performance of the proposed method over the existing reconstruction methods.

  14. Proposed test method for determining discharge rates from water closets

    DEFF Research Database (Denmark)

    Nielsen, V.; Fjord Jensen, T.

    At present the rates at which discharge takes place from sanitary appliances are mostly known only in the form of estimated average values. SBI has developed a measuring method enabling determination of the exact rate of discharge from a sanitary appliance as function of time. The methods depends...

  15. Boring of full scale deposition holes using a novel dry blind boring method

    Energy Technology Data Exchange (ETDEWEB)

    Autio, J.; Kirkkomaeki, T. [Saanio and Riekkola Oy, Helsinki (Finland)

    1996-10-01

    Three holes the size of deposition holes (depth 7.5 m and diameter 1.5 m) were bored in the Research Tunnel at Olkiluoto, Finland. A novel full-face boring technique was used based on rotary crushing of rock and removal of crushed rock by vacuum flushing through the drill string. The purpose of the work was to demonstrate the feasibility of the technique. During the boring test procedures were carried out in order to determine the effect of changes in operating parameters on the performance of the boring machine and the quality of the hole. The boring method was found to be technically feasible and efficient. Evaluation of the quality of the hole included studies of the geometry of the hole, measurements of the surface roughness using a laser profilometer and study of excavation disturbances in the zone adjacent to the surface of the holes using two novel methods, He-gas diffusion and the {sup 14}C-polymethylmethacrylate methods. 43 refs.

  16. Full-Scale Turbofan Engine Noise-Source Separation Using a Four-Signal Method

    Science.gov (United States)

    Hultgren, Lennart S.; Arechiga, Rene O.

    2016-01-01

    Contributions from the combustor to the overall propulsion noise of civilian transport aircraft are starting to become important due to turbofan design trends and expected advances in mitigation of other noise sources. During on-ground, static-engine acoustic tests, combustor noise is generally sub-dominant to other engine noise sources because of the absence of in-flight effects. Consequently, noise-source separation techniques are needed to extract combustor-noise information from the total noise signature in order to further progress. A novel four-signal source-separation method is applied to data from a static, full-scale engine test and compared to previous methods. The new method is, in a sense, a combination of two- and three-signal techniques and represents an attempt to alleviate some of the weaknesses of each of those approaches. This work is supported by the NASA Advanced Air Vehicles Program, Advanced Air Transport Technology Project, Aircraft Noise Reduction Subproject and the NASA Glenn Faculty Fellowship Program.

  17. Qualitative methods in radiography research: a proposed framework

    International Nuclear Information System (INIS)

    Adams, J.; Smith, T.

    2003-01-01

    Introduction: While radiography is currently developing a research base, which is important in terms of professional development and informing practice and policy issues in the field, the amount of research published by radiographers remains limited. However, a range of qualitative methods offer further opportunities for radiography research. Purpose: This paper briefly introduces a number of key qualitative methods (qualitative interviews, focus groups, observational methods, diary methods and document/text analysis) and sketches one possible framework for future qualitative work in radiography research. The framework focuses upon three areas for study: intra-professional issues; inter-professional issues; and clinical practice, patient and health delivery issues. While the paper outlines broad areas for future focus rather than providing a detailed protocol for how individual pieces of research should be conducted, a few research questions have been chosen and examples of possible qualitative methods required to answer such questions are outlined for each area. Conclusion: Given the challenges and opportunities currently facing the development of a research base within radiography, the outline of key qualitative methods and broad areas suitable for their application is offered as a useful tool for those within the profession looking to embark upon or enhance their research career

  18. Full Quantum Dynamics Simulation of a Realistic Molecular System Using the Adaptive Time-Dependent Density Matrix Renormalization Group Method.

    Science.gov (United States)

    Yao, Yao; Sun, Ke-Wei; Luo, Zhen; Ma, Haibo

    2018-01-18

    The accurate theoretical interpretation of ultrafast time-resolved spectroscopy experiments relies on full quantum dynamics simulations for the investigated system, which is nevertheless computationally prohibitive for realistic molecular systems with a large number of electronic and/or vibrational degrees of freedom. In this work, we propose a unitary transformation approach for realistic vibronic Hamiltonians, which can be coped with using the adaptive time-dependent density matrix renormalization group (t-DMRG) method to efficiently evolve the nonadiabatic dynamics of a large molecular system. We demonstrate the accuracy and efficiency of this approach with an example of simulating the exciton dissociation process within an oligothiophene/fullerene heterojunction, indicating that t-DMRG can be a promising method for full quantum dynamics simulation in large chemical systems. Moreover, it is also shown that the proper vibronic features in the ultrafast electronic process can be obtained by simulating the two-dimensional (2D) electronic spectrum by virtue of the high computational efficiency of the t-DMRG method.

  19. Full wave simulation of waves in ECRIS plasmas based on the finite element method

    Energy Technology Data Exchange (ETDEWEB)

    Torrisi, G. [INFN - Laboratori Nazionali del Sud, via S. Sofia 62, 95123, Catania, Italy and Università Mediterranea di Reggio Calabria, Dipartimento di Ingegneria dell' Informazione, delle Infrastrutture e dell' Energia Sostenibile (DIIES), Via Graziella, I (Italy); Mascali, D.; Neri, L.; Castro, G.; Patti, G.; Celona, L.; Gammino, S.; Ciavola, G. [INFN - Laboratori Nazionali del Sud, via S. Sofia 62, 95123, Catania (Italy); Di Donato, L. [Università degli Studi di Catania, Dipartimento di Ingegneria Elettrica Elettronica ed Informatica (DIEEI), Viale Andrea Doria 6, 95125 Catania (Italy); Sorbello, G. [INFN - Laboratori Nazionali del Sud, via S. Sofia 62, 95123, Catania, Italy and Università degli Studi di Catania, Dipartimento di Ingegneria Elettrica Elettronica ed Informatica (DIEEI), Viale Andrea Doria 6, 95125 Catania (Italy); Isernia, T. [Università Mediterranea di Reggio Calabria, Dipartimento di Ingegneria dell' Informazione, delle Infrastrutture e dell' Energia Sostenibile (DIIES), Via Graziella, I-89100 Reggio Calabria (Italy)

    2014-02-12

    This paper describes the modeling and the full wave numerical simulation of electromagnetic waves propagation and absorption in an anisotropic magnetized plasma filling the resonant cavity of an electron cyclotron resonance ion source (ECRIS). The model assumes inhomogeneous, dispersive and tensorial constitutive relations. Maxwell's equations are solved by the finite element method (FEM), using the COMSOL Multiphysics{sup ®} suite. All the relevant details have been considered in the model, including the non uniform external magnetostatic field used for plasma confinement, the local electron density profile resulting in the full-3D non uniform magnetized plasma complex dielectric tensor. The more accurate plasma simulations clearly show the importance of cavity effect on wave propagation and the effects of a resonant surface. These studies are the pillars for an improved ECRIS plasma modeling, that is mandatory to optimize the ion source output (beam intensity distribution and charge state, especially). Any new project concerning the advanced ECRIS design will take benefit by an adequate modeling of self-consistent wave absorption simulations.

  20. Deterministic alternatives to the full configuration interaction quantum Monte Carlo method for strongly correlated systems

    Science.gov (United States)

    Tubman, Norm; Whaley, Birgitta

    The development of exponential scaling methods has seen great progress in tackling larger systems than previously thought possible. One such technique, full configuration interaction quantum Monte Carlo, allows exact diagonalization through stochastically sampling of determinants. The method derives its utility from the information in the matrix elements of the Hamiltonian, together with a stochastic projected wave function, which are used to explore the important parts of Hilbert space. However, a stochastic representation of the wave function is not required to search Hilbert space efficiently and new deterministic approaches have recently been shown to efficiently find the important parts of determinant space. We shall discuss the technique of Adaptive Sampling Configuration Interaction (ASCI) and the related heat-bath Configuration Interaction approach for ground state and excited state simulations. We will present several applications for strongly correlated Hamiltonians. This work was supported through the Scientific Discovery through Advanced Computing (SciDAC) program funded by the U.S. Department of Energy, Office of Science, Advanced Scientific Computing Research and Basic Energy Sciences.

  1. "INTRODUCING A FULL VALIDATED ANALYTICAL PROCEDURE AS AN OFFICIAL COMPENDIAL METHOD FOR FENTANYL TRANSDERMAL PATCHES"

    Directory of Open Access Journals (Sweden)

    Amir Mehdizadeh

    2005-04-01

    Full Text Available A simple, sensitive and specific HPLC method and also a simple and fast extraction procedure were developed for quantitative analysis of fentanyl transdermal patches. Chloroform, methanol and ethanol were used as extracting solvents with recovery percent of 92.1, 94.3 and 99.4% respectively. Fentanyl was extracted with ethanol and the eluted fentanyl through the C18 column was monitored by UV detection at 230 nm. The linearity was at the range of 0.5-10 µg/mL with correlation coefficient (r2 of 0.9992. Both intra and inter-day accuracy and precision were within acceptable limits. The detection limit (DL and quantitation limit (QL were 0.15 and 0.5 µg/mL, respectively. Other validation characteristics such as selectivity, robustness and ruggedness were evaluated. Following method validation, a system suitability test (SST including capacity factor (k´, plate number (N, tailing factor (T, and RSD was defined for routine test.

  2. Comparison of tissue equalization, and premium view post-processing methods in full field digital mammography

    Energy Technology Data Exchange (ETDEWEB)

    Chen Baoying, E-mail: chenby128@yahoo.co [Department of Radiology, Tangdu Hospital, Fourth Military Medical University, Xinsi Road 1, 710038 Xi' an, Shaanxi (China); Wang Wei; Huang Jin; Zhao Ming; Cui Guangbin [Department of Radiology, Tangdu Hospital, Fourth Military Medical University, Xinsi Road 1, 710038 Xi' an, Shaanxi (China); Xu Jing [Cell Engineering Research Centre and Department of Cell Biology, State Key Laboratory of Cancer Biology, Fourth Military Medical University, Changle West Road 169, 710032 Xi' an, Shaanxi (China); Guo Wei; Du Pang; Li Pei [Department of Radiology, Tangdu Hospital, Fourth Military Medical University, Xinsi Road 1, 710038 Xi' an, Shaanxi (China); Yu Jun, E-mail: pclamper@163.co [Department of Preclinical Experiment Center, Fourth Military Medical University, Changle West Road 169, 710032 Xi' an, Shaanxi (China)

    2010-10-15

    Objective: To retrospectively evaluate the diagnostic abilities of 2 post-processing methods provided by GE Senographe DS system, tissue equalization (TE) and premium view (PV) in full field digital mammography (FFDM). Materials and methods: In accordance with the ethical standards of the World Medical Association, this study was approved by regional ethics committee and signed informed patient consents were obtained. We retrospectively reviewed digital mammograms from 101 women (mean age, 47 years; range, 23-81 years) in the modes of TE and PV, respectively. Three radiologists, fully blinded to the post-processing methods, all patient clinical information and histologic results, read images by using objective image interpretation criteria for diagnostic information end points such as lesion border delineation, definition of disease extent, visualization of internal and surrounding morphologic features of the lesions. Also, overall diagnostic impression in terms of lesion conspicuity, detectability and diagnostic confidence was assessed. Between-group comparisons were performed with Wilcoxon signed rank test. Results: Readers 1, 2, and 3 demonstrated significant overall better impression of PV in 29, 27, and 24 patients, compared with that for TE in 12, 13, and 11 patients, respectively (p < 0.05). Significant (p < 0.05) better impression of PV was also demonstrated for diagnostic information end points. Importantly, PV proved to be more sensitive than TE while detecting malignant lesions in dense breast rather than benign lesions and malignancy in non-dense breast (p < 0.01). Conclusion: PV compared with TE provides marked better diagnostic information in FFDM, particularly for patients with malignancy in dense breast.

  3. Comparison of tissue equalization, and premium view post-processing methods in full field digital mammography

    International Nuclear Information System (INIS)

    Chen Baoying; Wang Wei; Huang Jin; Zhao Ming; Cui Guangbin; Xu Jing; Guo Wei; Du Pang; Li Pei; Yu Jun

    2010-01-01

    Objective: To retrospectively evaluate the diagnostic abilities of 2 post-processing methods provided by GE Senographe DS system, tissue equalization (TE) and premium view (PV) in full field digital mammography (FFDM). Materials and methods: In accordance with the ethical standards of the World Medical Association, this study was approved by regional ethics committee and signed informed patient consents were obtained. We retrospectively reviewed digital mammograms from 101 women (mean age, 47 years; range, 23-81 years) in the modes of TE and PV, respectively. Three radiologists, fully blinded to the post-processing methods, all patient clinical information and histologic results, read images by using objective image interpretation criteria for diagnostic information end points such as lesion border delineation, definition of disease extent, visualization of internal and surrounding morphologic features of the lesions. Also, overall diagnostic impression in terms of lesion conspicuity, detectability and diagnostic confidence was assessed. Between-group comparisons were performed with Wilcoxon signed rank test. Results: Readers 1, 2, and 3 demonstrated significant overall better impression of PV in 29, 27, and 24 patients, compared with that for TE in 12, 13, and 11 patients, respectively (p < 0.05). Significant (p < 0.05) better impression of PV was also demonstrated for diagnostic information end points. Importantly, PV proved to be more sensitive than TE while detecting malignant lesions in dense breast rather than benign lesions and malignancy in non-dense breast (p < 0.01). Conclusion: PV compared with TE provides marked better diagnostic information in FFDM, particularly for patients with malignancy in dense breast.

  4. Proposed New Method of Interpretation of Infrared Ship Signature Requirements

    NARCIS (Netherlands)

    Neele, F.P.; Wilson, M.T.; Youern, K.

    2005-01-01

    new method of deriving and defining requirements for the infrared signature of new ships is presented. The current approach is to specify the maximum allowed temperature or radiance contrast of the ship with respect to its background. At present, in most NATO countries, it is the contractor’s

  5. Signal predictions for a proposed fast neutron interrogation method

    International Nuclear Information System (INIS)

    Sale, K.E.

    1992-12-01

    We have applied the Monte Carlo radiation transport code COG) to assess the utility of a proposed explosives detection scheme based on neutron emission. In this scheme a pulsed neutron beam is generated by an approximately seven MeV deuteron beam incident on a thick Be target. A scintillation detector operating in the current mode measures the neutrons transmitted through the object as a function of time. The flight time of unscattered neutrons from the source to the detector is simply related to the neutron energy. This information along with neutron cross section excitation functions is used to infer the densities of H, C, N and O in the volume sampled. The code we have chosen to use enables us to create very detailed and realistic models of the geometrical configuration of the system, the neutron source and of the detector response. By calculating the signals that will be observed for several configurations and compositions of interrogated object we can investigate and begin to understand how a system that could actually be fielded will perform. Using this modeling capability many early on with substantial savings in time and cost and with improvements in performance. We will present our signal predictions for simple single element test cases and for explosive compositions. From these studies it is dear that the interpretation of the signals from such an explosives identification system will pose a substantial challenge

  6. Depth Estimates for Slingram Electromagnetic Anomalies from Dipping Sheet-like Bodies by the Normalized Full Gradient Method

    Science.gov (United States)

    Dondurur, Derman

    2005-11-01

    The Normalized Full Gradient (NFG) method was proposed in the mid 1960s and was generally used for the downward continuation of the potential field data. The method eliminates the side oscillations which appeared on the continuation curves when passing through anomalous body depth. In this study, the NFG method was applied to Slingram electromagnetic anomalies to obtain the depth of the anomalous body. Some experiments were performed on the theoretical Slingram model anomalies in a free space environment using a perfectly conductive thin tabular conductor with an infinite depth extent. The theoretical Slingram responses were obtained for different depths, dip angles and coil separations, and it was observed from NFG fields of the theoretical anomalies that the NFG sections yield the depth information of top of the conductor at low harmonic numbers. The NFG sections consisted of two main local maxima located at both sides of the central negative Slingram anomalies. It is concluded that these two maxima also locate the maximum anomaly gradient points, which indicates the depth of the anomaly target directly. For both theoretical and field data, the depth of the maximum value on the NFG sections corresponds to the depth of the upper edge of the anomalous conductor. The NFG method was applied to the in-phase component and correct depth estimates were obtained even for the horizontal tabular conductor. Depth values could be estimated with a relatively small error percentage when the conductive model was near-vertical and/or the conductor depth was larger.

  7. Proposals of counting method for bubble detectors and their intercomparisons

    International Nuclear Information System (INIS)

    Ramalho, Eduardo; Silva, Ademir X.; Bellido, Luis F.; Facure, Alessandro; Pereira, Mario

    2009-01-01

    The study of neutron's spectrometry and dosimetry has become significantly easier due to relatively new devices called bubble detectors. Insensitive to gamma rays and composed by superheated emulsions, they still are subjects of many researches in Radiation Physics and Nuclear Engineering. In bubble detectors, either exposed to more intense neutron fields or for a long time, when more bubbles are produced, the statistical uncertainty during the dosimetric and spectrometric processes is reduced. A proposal of this nature is set up in this work, which presents ways to perform counting processes for bubble detectors and an updated proceeding to get the irradiated detectors' images in order to make the manual counting easier. Twelve BDS detectors were irradiated by RDS111 cyclotron from IEN's (Instituto de Engenharia Nuclear) and photographed using an assembly specially designed for this experiment. Counting was proceeded manually in a first moment; simultaneously, ImagePro was used in order to perform counting automatically. The bubble counting values, either manual or automatic, were compared and the time to get them and their difficult levels as well. After the bubble counting, the detectors' standardizes responses were calculated in both cases, according to BDS's manual and they were also compared. Among the results, the counting on these devices really becomes very hard at a large number of bubbles, besides higher variations in counting of many bubbles. Because of the good agreement between manual counting and the custom program, the last one revealed a good alternative in practical and economical levels. Despite the good results, the custom program needs of more adjustments in order to achieve more accuracy on higher counting on bubble detectors for neutron measurement applications. (author)

  8. Recognition of Time Stamps on Full-Disk Hα Images Using Machine Learning Methods

    Science.gov (United States)

    Xu, Y.; Huang, N.; Jing, J.; Liu, C.; Wang, H.; Fu, G.

    2016-12-01

    Observation and understanding of the physics of the 11-year solar activity cycle and 22-year magnetic cycle are among the most important research topics in solar physics. The solar cycle is responsible for magnetic field and particle fluctuation in the near-earth environment that have been found increasingly important in affecting the living of human beings in the modern era. A systematic study of large-scale solar activities, as made possible by our rich data archive, will further help us to understand the global-scale magnetic fields that are closely related to solar cycles. The long-time-span data archive includes both full-disk and high-resolution Hα images. Prior to the widely use of CCD cameras in 1990s, 35-mm films were the major media to store images. The research group at NJIT recently finished the digitization of film data obtained by the National Solar Observatory (NSO) and Big Bear Solar Observatory (BBSO) covering the period of 1953 to 2000. The total volume of data exceeds 60 TB. To make this huge database scientific valuable, some processing and calibration are required. One of the most important steps is to read the time stamps on all of the 14 million images, which is almost impossible to be done manually. We implemented three different methods to recognize the time stamps automatically, including Optical Character Recognition (OCR), Classification Tree and TensorFlow. The latter two are known as machine learning algorithms which are very popular now a day in pattern recognition area. We will present some sample images and the results of clock recognition from all three methods.

  9. A proposed method for fast determination of plasma parameters

    International Nuclear Information System (INIS)

    Braams, B.J.; Lackner, K.

    1984-09-01

    The method of function parametrization, developed and applied by H. Wind for fast data evaluation in high energy physics, is presented in the context of controlled fusion research. This method relies on statistical analysis of a data base of simulated experiments in order to obtain a functional representation for the intrinsic physical parameters of a system in terms of the values of the measurements. Some variations on Wind's original procedure are suggested. A specific application for tokamak experiments would be the determination of certain global parameters of the plasma, characterizing the current profile, shape of the cross-section, plasma pressure, and the internal inductance. The relevant measurements for this application include values of the poloidal field and flux external to the plasma, and a diamagnetic measurement. These may be combined with other diagnostics, such as electron-cyclotron emission and laser interferometry, in order to obtain also density and temperature profiles. There appears to be a capability for on-line determination of basic physical parameters, in a millisecond timescale on a minicomputer instead of in seconds on a large mainframe. (orig.)

  10. Standardisation of {sup 18}F by a coincidence method using full solid angle detectors

    Energy Technology Data Exchange (ETDEWEB)

    Nedjadi, Youcef, E-mail: youcef.nedjadi@chuv.c [Institut de Radiophysique Appliquee, Grand Pre 1, 1007 Lausanne (Switzerland); Bailat, Claude; Caffari, Yvan; Bochud, Francois [Institut de Radiophysique Appliquee, Grand Pre 1, 1007 Lausanne (Switzerland)

    2010-07-15

    A solution of {sup 18}F was standardised with a 4{pi}{beta}-4{pi}{gamma} coincidence counting system in which the beta detector is a one-inch diameter cylindrical UPS89 plastic scintillator, positioned at the bottom of a well-type 5''x5'' NaI(Tl) gamma-ray detector. Almost full detection efficiency-which was varied downwards electronically-was achieved in the beta-channel. Aliquots of this {sup 18}F solution were also measured using 4{pi}{gamma} NaI(Tl) integral counting and Monte Carlo calculated efficiencies as well as the CIEMAT-NIST method. Secondary measurements of the same solution were also performed with an IG11 ionisation chamber whose equivalent activity is traceable to the Systeme International de Reference through the contribution IRA-METAS made to it in 2001; IRA's degree of equivalence was found to be close to the key comparison reference value (KCRV). The {sup 18}F activity predicted by this coincidence system agrees closely with the ionisation chamber measurement and is compatible within one standard deviation of the other primary measurements. This work demonstrates that our new coincidence system can standardise short-lived radionuclides used in nuclear medicine.

  11. A Joint Method of Envelope Inversion Combined with Hybrid-domain Full Waveform Inversion

    Science.gov (United States)

    CUI, C.; Hou, W.

    2017-12-01

    Full waveform inversion (FWI) aims to construct high-precision subsurface models by fully using the information in seismic records, including amplitude, travel time, phase and so on. However, high non-linearity and the absence of low frequency information in seismic data lead to the well-known cycle skipping problem and make inversion easily fall into local minima. In addition, those 3D inversion methods that are based on acoustic approximation ignore the elastic effects in real seismic field, and make inversion harder. As a result, the accuracy of final inversion results highly relies on the quality of initial model. In order to improve stability and quality of inversion results, multi-scale inversion that reconstructs subsurface model from low to high frequency are applied. But, the absence of very low frequencies (time domain and inversion in the frequency domain. To accelerate the inversion, we adopt CPU/GPU heterogeneous computing techniques. There were two levels of parallelism. In the first level, the inversion tasks are decomposed and assigned to each computation node by shot number. In the second level, GPU multithreaded programming is used for the computation tasks in each node, including forward modeling, envelope extraction, DFT (discrete Fourier transform) calculation and gradients calculation. Numerical tests demonstrated that the combined envelope inversion + hybrid-domain FWI could obtain much faithful and accurate result than conventional hybrid-domain FWI. The CPU/GPU heterogeneous parallel computation could improve the performance speed.

  12. Visual assessment of BIPV retrofit design proposals for selected historical buildings using the saliency map method

    Directory of Open Access Journals (Sweden)

    Ran Xu

    2015-06-01

    Full Text Available With the increasing awareness of energy efficiency, many old buildings have to undergo a massive facade energy retrofit. How to predict the visual impact which solar installations on the aesthetic cultural value of these buildings has been a heated debate in Switzerland (and throughout the world. The usual evaluation method to describe the visual impact of BIPV is based on semantic and qualitative descriptors, and strongly dependent on personal preferences. The evaluation scale is therefore relative, flexible and imprecise. This paper proposes a new method to accurately measure the visual impact which BIPV installations have on a historical building by using the saliency map method. By imitating working principles of the human eye, it is measured how much the BIPV design proposals differ from the original building facade in the aspect of attracting human visual attention. The result is directly presented in a quantitative manner, and can be used to compare the fitness of different BIPV design proposals. The measuring process is numeric, objective and more precise.  

  13. Comparison among four proposed direct blood culture microbial identification methods using MALDI-TOF MS

    Directory of Open Access Journals (Sweden)

    Ali M. Bazzi

    2017-05-01

    Full Text Available Summary: Matrix-assisted laser desorption-ionization time-of-flight (MALDI-TOF mass spectrometry facilitates rapid and accurate identification of pathogens, which is critical for sepsis patients.In this study, we assessed the accuracy in identification of both Gram-negative and Gram-positive bacteria, except for Streptococcus viridans, using four rapid blood culture methods with Vitek MALDI-TOF-MS. We compared our proposed lysis centrifugation followed by washing and 30% acetic acid treatment method (method 2 with two other lysis centrifugation methods (washing and 30% formic acid treatment (method 1; 100% ethanol treatment (method 3, and picking colonies from 90 to 180 min subculture plates (method 4. Methods 1 and 2 identified all organisms down to species level with 100% accuracy, except for Streptococcus viridans, Streptococcus pyogenes, Enterobacter cloacae and Proteus vulgaris. The latter two were identified to genus level with 100% accuracy. Each method exhibited excellent accuracy and precision in terms of identification to genus level with certain limitations. Keywords: MALDI-TOF, Gram-negative, Gram-positive, Sepsis, Blood culture

  14. Full Seismic Waveform Tomography of the Japan region using Adjoint Methods

    Science.gov (United States)

    Steptoe, Hamish; Fichtner, Andreas; Rickers, Florian; Trampert, Jeannot

    2013-04-01

    We present a full-waveform tomographic model of the Japan region based on spectral-element wave propagation, adjoint techniques and seismic data from dense station networks. This model is intended to further our understanding of both the complex regional tectonics and the finite rupture processes of large earthquakes. The shallow Earth structure of the Japan region has been the subject of considerable tomographic investigation. The islands of Japan exist in an area of significant plate complexity: subduction related to the Pacific and Philippine Sea plates is responsible for the majority of seismicity and volcanism of Japan, whilst smaller micro-plates in the region, including the Okhotsk, and Okinawa and Amur, part of the larger North America and Eurasia plates respectively, contribute significant local intricacy. In response to the need to monitor and understand the motion of these plates and their associated faults, numerous seismograph networks have been established, including the 768 station high-sensitivity Hi-net network, 84 station broadband F-net and the strong-motion seismograph networks K-net and KiK-net in Japan. We also include the 55 station BATS network of Taiwan. We use this exceptional coverage to construct a high-resolution model of the Japan region from the full-waveform inversion of over 15,000 individual component seismograms from 53 events that occurred between 1997 and 2012. We model these data using spectral-element simulations of seismic wave propagation at a regional scale over an area from 120°-150°E and 20°-50°N to a depth of around 500 km. We quantify differences between observed and synthetic waveforms using time-frequency misfits allowing us to separate both phase and amplitude measurements whilst exploiting the complete waveform at periods of 15-60 seconds. Fréchet kernels for these misfits are calculated via the adjoint method and subsequently used in an iterative non-linear conjugate-gradient optimization. Finally, we employ

  15. Simulation in full-scale mock-ups: an ergonomics evaluation method?

    DEFF Research Database (Denmark)

    Andersen, Simone Nyholm; Broberg, Ole

    2014-01-01

    This paper presents and exploratory study of four simulation sessions in full-scale mock-ups of future hospital facilities.......This paper presents and exploratory study of four simulation sessions in full-scale mock-ups of future hospital facilities....

  16. Fully automatic and reference-marker-free image stitching method for full-spine and full-leg imaging with computed radiography

    Science.gov (United States)

    Wang, Xiaohui; Foos, David H.; Doran, James; Rogers, Michael K.

    2004-05-01

    Full-leg and full-spine imaging with standard computed radiography (CR) systems requires several cassettes/storage phosphor screens to be placed in a staggered arrangement and exposed simultaneously to achieve an increased imaging area. A method has been developed that can automatically and accurately stitch the acquired sub-images without relying on any external reference markers. It can detect and correct the order, orientation, and overlap arrangement of the subimages for stitching. The automatic determination of the order, orientation, and overlap arrangement of the sub-images consists of (1) constructing a hypothesis list that includes all cassette/screen arrangements, (2) refining hypotheses based on a set of rules derived from imaging physics, (3) correlating each consecutive sub-image pair in each hypothesis and establishing an overall figure-of-merit, (4) selecting the hypothesis of maximum figure-of-merit. The stitching process requires the CR reader to over scan each CR screen so that the screen edges are completely visible in the acquired sub-images. The rotational displacement and vertical displacement between two consecutive sub-images are calculated by matching the orientation and location of the screen edge in the front image and its corresponding shadow in the back image. The horizontal displacement is estimated by maximizing the correlation function between the two image sections in the overlap region. Accordingly, the two images are stitched together. This process is repeated for the newly stitched composite image and the next consecutive sub-image until a full-image composite is created. The method has been evaluated in both phantom experiments and clinical studies. The standard deviation of image misregistration is below one image pixel.

  17. Full waveform inversion using oriented time-domain imaging method for vertical transverse isotropic media

    KAUST Repository

    Zhang, Zhendong; Alkhalifah, Tariq Ali

    2017-01-01

    Full waveform inversion for reection events is limited by its linearized update re-quirements given by a process equivalent to migration. Unless the background velocity model is reasonably accurate, the resulting gradient can have an inaccurate

  18. A simple method to achieve full-field and real-scale reconstruction using a movable stereo rig

    Science.gov (United States)

    Gu, Feifei; Zhao, Hong; Song, Zhan; Tang, Suming

    2018-06-01

    This paper introduces a simple method to achieve full-field and real-scale reconstruction using a movable binocular vision system (MBVS). The MBVS is composed of two cameras, one is called the tracking camera, and the other is called the working camera. The tracking camera is used for tracking the positions of the MBVS and the working camera is used for the 3D reconstruction task. The MBVS has several advantages compared with a single moving camera or multi-camera networks. Firstly, the MBVS could recover the real-scale-depth-information from the captured image sequences without using auxiliary objects whose geometry or motion should be precisely known. Secondly, the removability of the system could guarantee appropriate baselines to supply more robust point correspondences. Additionally, using one camera could avoid the drawback which exists in multi-camera networks, that the variability of a cameras’ parameters and performance could significantly affect the accuracy and robustness of the feature extraction and stereo matching methods. The proposed framework consists of local reconstruction and initial pose estimation of the MBVS based on transferable features, followed by overall optimization and accurate integration of multi-view 3D reconstruction data. The whole process requires no information other than the input images. The framework has been verified with real data, and very good results have been obtained.

  19. Monitoring temperature reactivity coefficient by noise method in a NPP at full power

    International Nuclear Information System (INIS)

    Aguilar, O.; Por, G.

    1987-04-01

    A new method based on noise measurement was used to estimate the temperature reactivity coefficient of the PAKS-2 reactor during the entire fuel cycle. Based on the measurements it is possible to measure the dependence of reactivity coefficient on boron concentration. Good agreement was found between the results obtained by the new method and by the conventional ones. Based on this method a new equipment can be develop which assures permanent measurements during operation. (author)

  20. Construction Method of Display Proposal for Commodities in Sales Promotion by Genetic Algorithm

    Science.gov (United States)

    Yumoto, Masaki

    In a sales promotion task, wholesaler prepares and presents the display proposal for commodities in order to negotiate with retailer's buyers what commodities they should sell. For automating the sales promotion tasks, the proposal has to be constructed according to the target retailer's buyer. However, it is difficult to construct the proposal suitable for the target retail store because of too much combination of commodities. This paper proposes a construction method by Genetic algorithm (GA). The proposed method represents initial display proposals for commodities with genes, improve ones with the evaluation value by GA, and rearrange one with the highest evaluation value according to the classification of commodity. Through practical experiment, we can confirm that display proposal by the proposed method is similar with the one constructed by a wholesaler.

  1. A convergent numerical method for the full Navier-Stokes-Fourier system in smooth physical domains

    Czech Academy of Sciences Publication Activity Database

    Feireisl, Eduard; Hošek, Radim; Michálek, Martin

    2016-01-01

    Roč. 54, č. 5 (2016), s. 3062-3082 ISSN 0036-1429 EU Projects: European Commission(XE) 320078 - MATHEF Institutional support: RVO:67985840 Keywords : Navier-Stokes- Fourier system * finite element method * finite volume method Subject RIV: BA - General Mathematics Impact factor: 1.978, year: 2016 http://epubs.siam.org/doi/abs/10.1137/15M1011809

  2. A convergent numerical method for the full Navier-Stokes-Fourier system in smooth physical domains

    Czech Academy of Sciences Publication Activity Database

    Feireisl, Eduard; Hošek, Radim; Michálek, Martin

    2016-01-01

    Roč. 54, č. 5 (2016), s. 3062-3082 ISSN 0036-1429 EU Projects: European Commission(XE) 320078 - MATHEF Institutional support: RVO:67985840 Keywords : Navier-Stokes-Fourier system * finite element method * finite volume method Subject RIV: BA - General Mathematics Impact factor: 1.978, year: 2016 http://epubs.siam.org/doi/abs/10.1137/15M1011809

  3. Proposal for a new detection method of substance abuse risk in Croatian adolescents

    Directory of Open Access Journals (Sweden)

    Sanja Tatalovic Vorkapic

    2011-01-01

    Full Text Available One of the most important factors of successful substance abuse treatment is the early start of the same treatment. Recent selection method for identification of Croatian adolescents in the substance abuse risk that has been using drug tests from urine samples, has been simple and exact on the one hand, but on the other, has been very rare and usually guided by the pressure of parents or the court. Besides, such method presented the source of legal and ethical questions. So, the proposal of application of standardized psychological tests during systematic medical exams of Croatian adolescents at the age range of 15-22 years could help with the early detection of those adolescents who were in the substance abuse risk or already had the developed addiction problem.

  4. The theoretical study of full spectrum analysis method for airborne gamma-ray spectrometric data

    International Nuclear Information System (INIS)

    Ni Weichong

    2011-01-01

    Spectra of airborne gamma-ray spectrometry was found to be the synthesis of spectral components of radioelement sources by analyzing the constitution of radioactive sources for airborne gamma-ray spectrometric survey and establishing the models of gamma-ray measurement. The mathematical equation for analysising airborne gamma-ray full spectrometric data can be expressed into matrix and related expansions were developed for the mineral resources exploration, environmental radiation measurement, nuclear emergency monitoring, and so on. Theoretical study showed that the atmospheric radon could be directly computed by airborne gamma-ray spectrometric data with full spectrum analysis without the use of the accessional upward-looking detectors. (authors)

  5. Model Predictive Flight Control System with Full State Observer using H∞ Method

    Science.gov (United States)

    Sanwale, Jitu; Singh, Dhan Jeet

    2018-03-01

    This paper presents the application of the model predictive approach to design a flight control system (FCS) for longitudinal dynamics of a fixed wing aircraft. Longitudinal dynamics is derived for a conventional aircraft. Open loop aircraft response analysis is carried out. Simulation studies are illustrated to prove the efficacy of the proposed model predictive controller using H ∞ state observer. The estimation criterion used in the {H}_{∞} observer design is to minimize the worst possible effects of the modelling errors and additive noise on the parameter estimation.

  6. Contribution for an Urban Geomorphoheritage Assessment Method: Proposal from Three Geomorphosites in Rome (Italy

    Directory of Open Access Journals (Sweden)

    Pica Alessia

    2017-09-01

    Full Text Available Urban geomorphology has important implications in spatial planning of human activities, and it also has a geotouristic potential due to the relationship between cultural and geomorphological heritage. Despite the introduction of the term Anthropocene to describe the deep influence that human activities have had in recent times on Earth evolution, urban geomorphological heritage studies are relatively rare and limited and urban geotourism development is recent. The analysis of the complex urban landscape often need the integration of multidisciplinary data. This study aims to propose the first urban geomorphoheritage assessment method, which originates after long-lasting previous geomorphological and geotouristic studies on Rome city centre, it depict rare examples of the geomorphological mapping of a metropolis and, at the same time, of an inventory of urban geomorphosites. The proposal is applied to geomorphosites in the Esquilino neighbourhood of Rome, whose analysis confirm the need for an ad hoc method for assessing urban geomorphosites, as already highlighted in the most recent literature on the topic. The urban geomorphoheritage assessment method is based on: (i the urban geomorphological analysis by means of multitemporal and multidisciplinary data; (ii the geomorphosite inventory; and (iii the geomorphoheritage assessment and enhancement. One challenge is to assess invisible geomorphosites that are widespread in urban context. To this aim, we reworked the attributes describing the Value of a site for Geotourism in order to build up a specific methodology for the analysis of the urban geomorphological heritage.

  7. The experimental method of measurement for spatial distribution of full aperture backscatter light by circular PIN-array

    International Nuclear Information System (INIS)

    Zhao Xuefeng; Wang Chuanke; Hu Feng; Kuang Longyu; Wang Zhebin; Li Sanwei; Liu Shengye; Jiang Gang

    2011-01-01

    The spatial distribution of backscatter light is very important for understanding the production of backscatter light. The experimental method of spatial distribution of full aperture backscatter light is based on the circular PIN array composed of concentric orbicular multi-PIN detectors. The image of backscatter light spatial distribution of full aperture SBS is obtained by measuring spatial distribution of full aperture backscatter light using the method in the experiment of laser hohlraum targets interaction at 'Shenguang II'. A preliminary method to measure spatial distribution of full aperture backscatter light is established. (authors)

  8. A simple method to calculate the neutron flow through full ducts

    International Nuclear Information System (INIS)

    Faik Ouahab, Z.; Jehouani, A.; Ghassoun, J.; Senhou, N.; Groetz, J.E.

    2010-01-01

    Summary of a study of assessment of the probability for neutrons to be guided in a full duct with a square cross section and doubly bent. Two software have been developed, based on the Monte Carlo simulation, to compute the neutron transmission probability at the end of the duct. Results are in good agreement with that obtained with the MCNP-5 code. The neutron flow and probability at the duct end have been determined for different materials and different duct dimensions

  9. A Concealed Car Extraction Method Based on Full-Waveform LiDAR Data

    Directory of Open Access Journals (Sweden)

    Chuanrong Li

    2016-01-01

    Full Text Available Concealed cars extraction from point clouds data acquired by airborne laser scanning has gained its popularity in recent years. However, due to the occlusion effect, the number of laser points for concealed cars under trees is not enough. Thus, the concealed cars extraction is difficult and unreliable. In this paper, 3D point cloud segmentation and classification approach based on full-waveform LiDAR was presented. This approach first employed the autocorrelation G coefficient and the echo ratio to determine concealed cars areas. Then the points in the concealed cars areas were segmented with regard to elevation distribution of concealed cars. Based on the previous steps, a strategy integrating backscattered waveform features and the view histogram descriptor was developed to train sample data of concealed cars and generate the feature pattern. Finally concealed cars were classified by pattern matching. The approach was validated by full-waveform LiDAR data and experimental results demonstrated that the presented approach can extract concealed cars with accuracy more than 78.6% in the experiment areas.

  10. A simple method for the parallel deep sequencing of full influenza A genomes

    DEFF Research Database (Denmark)

    Kampmann, Marie-Louise; Fordyce, Sarah Louise; Avila Arcos, Maria del Carmen

    2011-01-01

    Given the major threat of influenza A to human and animal health, and its ability to evolve rapidly through mutation and reassortment, tools that enable its timely characterization are necessary to help monitor its evolution and spread. For this purpose, deep sequencing can be a very valuable tool....... This study reports a comprehensive method that enables deep sequencing of the complete genomes of influenza A subtypes using the Illumina Genome Analyzer IIx (GAIIx). By using this method, the complete genomes of nine viruses were sequenced in parallel, representing the 2009 pandemic H1N1 virus, H5N1 virus...

  11. The clinically-integrated randomized trial: proposed novel method for conducting large trials at low cost

    Directory of Open Access Journals (Sweden)

    Scardino Peter T

    2009-03-01

    Full Text Available Abstract Introduction Randomized controlled trials provide the best method of determining which of two comparable treatments is preferable. Unfortunately, contemporary randomized trials have become increasingly expensive, complex and burdened by regulation, so much so that many trials are of doubtful feasibility. Discussion Here we present a proposal for a novel, streamlined approach to randomized trials: the "clinically-integrated randomized trial". The key aspect of our methodology is that the clinical experience of the patient and doctor is virtually indistinguishable whether or not the patient is randomized, primarily because outcome data are obtained from routine clinical data, or from short, web-based questionnaires. Integration of a randomized trial into routine clinical practice also implies that there should be an attempt to randomize every patient, a corollary of which is that eligibility criteria are minimized. The similar clinical experience of patients on- and off-study also entails that the marginal cost of putting an additional patient on trial is negligible. We propose examples of how the clinically-integrated randomized trial might be applied in four distinct areas of medicine: comparisons of surgical techniques, "me too" drugs, rare diseases and lifestyle interventions. Barriers to implementing clinically-integrated randomized trials are discussed. Conclusion The proposed clinically-integrated randomized trial may allow us to enlarge dramatically the number of clinical questions that can be addressed by randomization.

  12. Implementation of a fast running full core pin power reconstruction method in DYN3D

    International Nuclear Information System (INIS)

    Gomez-Torres, Armando Miguel; Sanchez-Espinoza, Victor Hugo; Kliem, Sören; Gommlich, Andre

    2014-01-01

    Highlights: • New pin power reconstruction (PPR) method for the nodal diffusion code DYN3D. • Flexible PPR method applicable to a single, a group or to all fuel assemblies (square, hex). • Combination of nodal with pin-wise solutions (non-conform geometry). • PPR capabilities shown for REA of a Minicore (REA) PWR whole core. - Abstract: This paper presents a substantial extension of the pin power reconstruction (PPR) method used in the reactor dynamics code DYN3D with the aim to better describe the heterogeneity within the fuel assembly during reactor simulations. The flexibility of the new implemented PPR permits the local spatial refinement of one fuel assembly, of a cluster of fuel assemblies, of a quarter or eight of a core or even of a whole core. The application of PPR in core regions of interest will pave the way for the coupling with sub-channel codes enabling the prediction of local safety parameters. One of the main advantages of considering regions and not only a hot fuel assembly (FA) is the fact that the cross flow within this region can be taken into account by the subchannel code. The implementation of the new PPR method has been tested analysing a rod ejection accident (REA) in a PWR minicore consisting of 3 × 3 FA. Finally, the new capabilities of DNY3D are demonstrated by the analysing a boron dilution transient in a PWR MOX core and the pin power of a VVER-1000 reactor at stationary conditions

  13. Implementation of a fast running full core pin power reconstruction method in DYN3D

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Torres, Armando Miguel [Instituto Nacional de Investigaciones Nucleares, Department of Nuclear Systems, Carretera Mexico – Toluca s/n, La Marquesa, 52750 Ocoyoacac (Mexico); Sanchez-Espinoza, Victor Hugo, E-mail: victor.sanchez@kit.edu [Karlsruhe Institute of Technology, Institute for Neutron Physics and Reactor Technology, Hermann-vom-Helmhotz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Kliem, Sören; Gommlich, Andre [Helmholtz-Zentrum Dresden-Rossendorf, Bautzner Landstraße 400, 01328 Dresden (Germany)

    2014-07-01

    Highlights: • New pin power reconstruction (PPR) method for the nodal diffusion code DYN3D. • Flexible PPR method applicable to a single, a group or to all fuel assemblies (square, hex). • Combination of nodal with pin-wise solutions (non-conform geometry). • PPR capabilities shown for REA of a Minicore (REA) PWR whole core. - Abstract: This paper presents a substantial extension of the pin power reconstruction (PPR) method used in the reactor dynamics code DYN3D with the aim to better describe the heterogeneity within the fuel assembly during reactor simulations. The flexibility of the new implemented PPR permits the local spatial refinement of one fuel assembly, of a cluster of fuel assemblies, of a quarter or eight of a core or even of a whole core. The application of PPR in core regions of interest will pave the way for the coupling with sub-channel codes enabling the prediction of local safety parameters. One of the main advantages of considering regions and not only a hot fuel assembly (FA) is the fact that the cross flow within this region can be taken into account by the subchannel code. The implementation of the new PPR method has been tested analysing a rod ejection accident (REA) in a PWR minicore consisting of 3 × 3 FA. Finally, the new capabilities of DNY3D are demonstrated by the analysing a boron dilution transient in a PWR MOX core and the pin power of a VVER-1000 reactor at stationary conditions.

  14. Boring of full scale deposition holes using a novel dry blind boring method

    International Nuclear Information System (INIS)

    Autio, J.; Kirkkomaeki, T.

    1996-11-01

    As a part of the Finnish radioactive waste disposal research three holes (the size of deposition holes) were bored in the research tunnel at Olkiluoto in Finland. A novel full-face boring technique was used based on rotary crushing of rock and removal of crushed rock by vacuum flushing through the drill string an the purpose of the work was to demonstrate the feasibility of the technique. During the boring test procedures were carried out in order to determine the effect of charges in operating parameters on the performance of the boring machine and the quality of the hole. (refs.)

  15. Boring of full scale deposition holes using a novel dry blind boring method

    Energy Technology Data Exchange (ETDEWEB)

    Autio, J.; Kirkkomaeki, T. [Saanio and Riekkola Consulting Engineers, Helsinki (Finland)

    1996-11-01

    As a part of the Finnish radioactive waste disposal research three holes (the size of deposition holes) were bored in the research tunnel at Olkiluoto in Finland. A novel full-face boring technique was used based on rotary crushing of rock and removal of crushed rock by vacuum flushing through the drill string an the purpose of the work was to demonstrate the feasibility of the technique. During the boring test procedures were carried out in order to determine the effect of charges in operating parameters on the performance of the boring machine and the quality of the hole. (refs.).

  16. Application of probabilistic methods for sizing of safety factors in studies on defect harm fullness

    International Nuclear Information System (INIS)

    Ardillon, E.; Pitner, P.

    1996-01-01

    The design rules that are currently under application in nuclear engineering recommend the use of deterministic analysis methods. Probabilistic methods allow the uncertainties inherent in input variables of the analytical model to be taken into account owing to data provided by operation feedback so as to better evaluate the link between the deterministic margins adopted and the actual risk level. In the Resistance R/Loading L elementary case where the variables are Gaussian, there is an explicit relation between the required safety level and the partial safety coefficients which affect each variable. In the complex case of a flawed pipe subjected to various modes of ruin where many random variables are not Gaussian, one can obtain implicit relations. These relations allow a certain flexibility when choosing the coefficients, which poses the problem of their optimum calibration. The choice of coefficients based upon the coordinates of the ''most probable failure point'' illustrates this approach. (authors). 7 refs., 5 figs., 2 tabs

  17. Elastic full waveform inversion based on the homogenization method: theoretical framework and 2-D numerical illustrations

    Science.gov (United States)

    Capdeville, Yann; Métivier, Ludovic

    2018-05-01

    Seismic imaging is an efficient tool to investigate the Earth interior. Many of the different imaging techniques currently used, including the so-called full waveform inversion (FWI), are based on limited frequency band data. Such data are not sensitive to the true earth model, but to a smooth version of it. This smooth version can be related to the true model by the homogenization technique. Homogenization for wave propagation in deterministic media with no scale separation, such as geological media, has been recently developed. With such an asymptotic theory, it is possible to compute an effective medium valid for a given frequency band such that effective waveforms and true waveforms are the same up to a controlled error. In this work we make the link between limited frequency band inversion, mainly FWI, and homogenization. We establish the relation between a true model and an FWI result model. This relation is important for a proper interpretation of FWI images. We numerically illustrate, in the 2-D case, that an FWI result is at best the homogenized version of the true model. Moreover, it appears that the homogenized FWI model is quite independent of the FWI parametrization, as long as it has enough degrees of freedom. In particular, inverting for the full elastic tensor is, in each of our tests, always a good choice. We show how the homogenization can help to understand FWI behaviour and help to improve its robustness and convergence by efficiently constraining the solution space of the inverse problem.

  18. Full-Scale Passive Earth Entry Vehicle Landing Tests: Methods and Measurements

    Science.gov (United States)

    Littell, Justin D.; Kellas, Sotiris

    2018-01-01

    During the summer of 2016, a series of drop tests were conducted on two passive earth entry vehicle (EEV) test articles at the Utah Test and Training Range (UTTR). The tests were conducted to evaluate the structural integrity of a realistic EEV vehicle under anticipated landing loads. The test vehicles were lifted to an altitude of approximately 400m via a helicopter and released via release hook into a predesignated 61 m landing zone. Onboard accelerometers were capable of measuring vehicle free flight and impact loads. High-speed cameras on the ground tracked the free-falling vehicles and data was used to calculate critical impact parameters during the final seconds of flight. Additional sets of high definition and ultra-high definition cameras were able to supplement the high-speed data by capturing the release and free flight of the test articles. Three tests were successfully completed and showed that the passive vehicle design was able to withstand the impact loads from nominal and off-nominal impacts at landing velocities of approximately 29 m/s. Two out of three test resulted in off-nominal impacts due to a combination of high winds at altitude and the method used to suspend the vehicle from the helicopter. Both the video and acceleration data captured is examined and discussed. Finally, recommendations for improved release and instrumentation methods are presented.

  19. Effect of MELT method on thoracolumbar connective tissue: The full study.

    Science.gov (United States)

    Sanjana, Faria; Chaudhry, Hans; Findley, Thomas

    2017-01-01

    Altered connective tissue structure has been identified in adults with chronic low back pain (LBP). A self-care treatment for managing LBP is the MELT method. The MELT method is a hands-off, self-treatment that is said to alleviate chronic pain, release tension and restore mobility, utilizing specialized soft treatments balls, soft body roller and techniques mimicking manual therapy. The objective of this study was to determine whether thickness of thoracolumbar connective tissue and biomechanical and viscoelastic properties of myofascial tissue in the low back region change in subjects with chronic LBP as a result of MELT. This study was designed using a quasi experimental pre-post- design that analyzed data from subjects who performed MELT. Using ultrasound imaging and an algorithm developed in MATLAB, thickness of thoracolumbar connective tissue was analyzed in 22 subjects. A hand-held digital palpation device, called the MyotonPRO, was used to assess biomechanical properties such as stiffness, elasticity, tone and mechanical stress relaxation time of the thoracolumbar myofascial tissue. A forward bending test assessing flexibility and pain scale was added to see if MELT affected subjects with chronic LBP. A significant decrease in connective tissue thickness and pain was observed in participants. Significant increase in flexibility was also recorded. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Computation of a coastal protection, using classical method, the PIANC-method or a full probabilistic approach ?

    NARCIS (Netherlands)

    Verhagen, H.J.

    2003-01-01

    In a classical design approach to breakwaters a design wave height is determined, and filled in into a design formula. Some undefined safety is added. In the method using partial safety coefficients (as developed by PIANC [1992] and recently also adopted by the Coastal Engineering Manual of the US

  1. A critical assessment of the microorganisms proposed to be important to enhanced biological phosphorus removal in full-scale wastewater treatment systems

    DEFF Research Database (Denmark)

    Stokholm-Bjerregaard, Mikkel; McIlroy, Simon Jon; Nierychlo, Marta

    2017-01-01

    accumulating organisms (PAOs). Also considered important to EBPR are the glycogen accumulating organisms (GAOs), which are theorized to compete with the PAOs for resources at the expense of P removal efficiency. Numerous studies have sought to identify the PAOs and their GAOs competitors, with several...... sequencing. The microbial community structure in all plants was relatively stable over time. Evidence for the role of the proposed PAOs and GAOs in EBPR varies and is critically assessed, in light of their calculated amplicon abundances, to indicate which of these are important in full-scale systems...... plants. Despite observed high abundances of GAOs (periodically exceeding 20% of the amplicon reads), P removal performance was maintained, indicating that these organisms were not outcompeting the PAOs in these EBPR systems. Phylogenetic diversity within each of the PAOs and GAOs genera was observed...

  2. Proposal for a Five-Step Method to Elicit Expert Judgment

    Directory of Open Access Journals (Sweden)

    Duco Veen

    2017-12-01

    Full Text Available Elicitation is a commonly used tool to extract viable information from experts. The information that is held by the expert is extracted and a probabilistic representation of this knowledge is constructed. A promising avenue in psychological research is to incorporated experts’ prior knowledge in the statistical analysis. Systematic reviews on elicitation literature however suggest that it might be inappropriate to directly obtain distributional representations from experts. The literature qualifies experts’ performance on estimating elements of a distribution as unsatisfactory, thus reliably specifying the essential elements of the parameters of interest in one elicitation step seems implausible. Providing feedback within the elicitation process can enhance the quality of the elicitation and interactive software can be used to facilitate the feedback. Therefore, we propose to decompose the elicitation procedure into smaller steps with adjustable outcomes. We represent the tacit knowledge of experts as a location parameter and their uncertainty concerning this knowledge by a scale and shape parameter. Using a feedback procedure, experts can accept the representation of their beliefs or adjust their input. We propose a Five-Step Method which consists of (1 Eliciting the location parameter using the trial roulette method. (2 Provide feedback on the location parameter and ask for confirmation or adjustment. (3 Elicit the scale and shape parameter. (4 Provide feedback on the scale and shape parameter and ask for confirmation or adjustment. (5 Use the elicited and calibrated probability distribution in a statistical analysis and update it with data or to compute a prior-data conflict within a Bayesian framework. User feasibility and internal validity for the Five-Step Method are investigated using three elicitation studies.

  3. A Proposal of Operational Risk Management Method Using FMEA for Drug Manufacturing Computerized System

    Science.gov (United States)

    Takahashi, Masakazu; Nanba, Reiji; Fukue, Yoshinori

    This paper proposes operational Risk Management (RM) method using Failure Mode and Effects Analysis (FMEA) for drug manufacturing computerlized system (DMCS). The quality of drug must not be influenced by failures and operational mistakes of DMCS. To avoid such situation, DMCS has to be conducted enough risk assessment and taken precautions. We propose operational RM method using FMEA for DMCS. To propose the method, we gathered and compared the FMEA results of DMCS, and develop a list that contains failure modes, failures and countermeasures. To apply this list, we can conduct RM in design phase, find failures, and conduct countermeasures efficiently. Additionally, we can find some failures that have not been found yet.

  4. Improved Full-Newton Step O(nL) Infeasible Interior-Point Method for Linear Optimization

    NARCIS (Netherlands)

    Gu, G.; Mansouri, H.; Zangiabadi, M.; Bai, Y.Q.; Roos, C.

    2009-01-01

    We present several improvements of the full-Newton step infeasible interior-point method for linear optimization introduced by Roos (SIAM J. Optim. 16(4):1110–1136, 2006). Each main step of the method consists of a feasibility step and several centering steps. We use a more natural feasibility step,

  5. A Method for Proposing Valued-Adding Attributes in Customized Housing

    Directory of Open Access Journals (Sweden)

    Cynthia S. Hentschke

    2014-12-01

    Full Text Available In most emerging economies, there has been many incentives and high availability of funding for low-cost housing projects. This has encouraged product standardization and the application of mass production ideas, based on the assumption that this is the most effective strategy for reducing costs. However, the delivery of highly standardized housing units to customers with different needs, without considering their lifestyle and perception of value, often results in inadequate products. Mass customization has been pointed out as an effective strategy to improve value generation in low-cost housing projects, and to avoid waste caused by renovations done in dwellings soon after occupancy. However, one of the main challenges for the implementation of mass customization is the definition of a set of relevant options based on users’ perceived value. The aim of this paper is to propose a method for defining value adding attributes in customized housing projects, which can support decision-making in product development. The means-end chain theory was used as theoretical framework to connect product attributes and costumers’ values, through the application of the laddering technique. The method was tested in two house-building projects delivered by a company from Brazil. The main contribution of this method is to indicate the customization units that are most important for users along with the explanation of why those units are the most relevant ones.

  6. Proposal for a method to estimate nutrient shock effects in bacteria

    Directory of Open Access Journals (Sweden)

    Azevedo Nuno F

    2012-08-01

    Full Text Available Abstract Background Plating methods are still the golden standard in microbiology; however, some studies have shown that these techniques can underestimate the microbial concentrations and diversity. A nutrient shock is one of the mechanisms proposed to explain this phenomenon. In this study, a tentative method to assess nutrient shock effects was tested. Findings To estimate the extent of nutrient shock effects, two strains isolated from tap water (Sphingomonas capsulata and Methylobacterium sp. and two culture collection strains (E. coli CECT 434 and Pseudomonas fluorescens ATCC 13525 were exposed both to low and high nutrient conditions for different times and then placed in low nutrient medium (R2A and rich nutrient medium (TSA. The average improvement (A.I. of recovery between R2A and TSA for the different times was calculated to more simply assess the difference obtained in culturability between each medium. As expected, A.I. was higher when cells were plated after the exposition to water than when they were recovered from high-nutrient medium showing the existence of a nutrient shock for the diverse bacteria used. S. capsulata was the species most affected by this phenomenon. Conclusions This work provides a method to consistently determine the extent of nutrient shock effects on different microorganisms and hence quantify the ability of each species to deal with sudden increases in substrate concentration.

  7. Proposed Suitable Methods to Detect Transient Regime Switching to Improve Power Quality with Wavelet Transform

    Directory of Open Access Journals (Sweden)

    Javad Safaee Kuchaksaraee

    2016-10-01

    Full Text Available The increasing consumption of electrical energy and the use of non-linear loads that create transient regime states in distribution networks is increasing day by day. This is the only reason due to which the analysis of power quality for energy sustainability in power networks has become more important. Transients are often created by energy injection through switching or lightning and make changes in voltage and nominal current. Sudden increase or decrease in voltage or current makes characteristics of the transient regime. This paper shed some lights on the capacitor bank switching, which is one of the main causes for oscillatory transient regime states in the distribution network, using wavelet transform. The identification of the switching current of capacitor bank and the internal fault current of the transformer to prevent the unnecessary outage of the differential relay, it propose a new smart method. The accurate performance of this method is shown by simulation in EMTP and MATLAB (matrix laboratory software.

  8. Applicability of the proposed evaluation method for social infrastructures to nuclear power plants

    International Nuclear Information System (INIS)

    Ichimura, Tomiyasu

    2015-01-01

    This study proposes an evaluation method for social infrastructures, and verifies the applicability of the proposed evaluation method to social infrastructures by applying it to nuclear power plants, which belong to social infrastructures. In the proposed evaluation method for social infrastructures, the authors chose four evaluation viewpoints and proposed common evaluation standards for the evaluation indexes obtained from each viewpoint. By applying this system to the evaluation of nuclear power plants, the evaluation index examples were obtained from the evaluation viewpoints. Furthermore, when the level of the common evaluation standards of the proposed evaluation method was applied to the evaluation of the activities of nuclear power plants based on the regulations, it was confirmed that these activities are at the highest level. Through this application validation, it was clarified that the proposed evaluation method for social infrastructures had certain effectiveness. The four evaluation viewpoints are 'service,' 'environment,' 'action factor,' and 'operation and management.' Part of the application examples to a nuclear power plant are as follows: (1) in the viewpoint of service: the operation rate of the power plant, and operation costs, and (2) in the viewpoint of environment: external influence related to nuclear waste and radioactivity, and external effect related to cooling water. (A.O.)

  9. Magnetism of hexagonal close-packed nickel calculated by full-potential linearized augmented plane wave method

    International Nuclear Information System (INIS)

    Tian, F.; Tian, H.; Whitmore, L.; Ye, L.Y.

    2015-01-01

    The energy dependent on volume of hexagonal close-packed (hcp) nickel with different magnetism is calculated by full-potential linearized augmented plane wave method. Based on the calculation ferromagnetic state is found to be the most stable state. The magnetic moment of hcp Ni is calculated and compared to those calculated by different pseudo-potential methods. Furthermore, it is also compared to that of face-centered cubic (fcc) one with the reason discussed

  10. Full 3D internal strain measurement for device packaging materials using synchrotron laminography and volumetric digital image correlation method

    International Nuclear Information System (INIS)

    Asada, Takashi; Kimura, Hidehiko; Yamaguchi, Satoshi; Kano, Taiki; Kajiwara, Kentaro

    2014-01-01

    In order to measure full 3D internal strain field of resin molding compound specimens, synchrotron computed tomography and laminography at SPring-8 were performed. Then the reconstructed images were applied to 3D digital image correlation method to compute internal strain field. The results showed that internal strains in resin molding compound could be visualized in this way. (author)

  11. A proposal on evaluation method of neutron absorption performance to substitute conventional neutron attenuation test

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Je Hyun; Shim, Chang Ho [Dept. of Nuclear Engineering, Hanyang University, Seoul (Korea, Republic of); Kim, Sung Hyun [Nuclear Fuel Cycle Waste Treatment Research Division, Research Reactor Institute, Kyoto University, Osaka (Japan); Choe, Jung Hun; Cho, In Hak; Park, Hwan Seo [Ionizing Radiation Center, Nuclear Fuel Cycle Waste Treatment Research Division, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Hyun Seo; Kim, Jung Ho; Kim, Yoon Ho [Ionizing Radiation Center, Korea Research Institute of Standards and Science, Daejeon (Korea, Republic of)

    2016-12-15

    For a verification of newly-developed neutron absorbers, one of guidelines on the qualification and acceptance of neutron absorbers is the neutron attenuation test. However, this approach can cause a problem for the qualifications that it cannot distinguish how the neutron attenuates from materials. In this study, an estimation method of neutron absorption performances for materials is proposed to detect both direct penetration and back-scattering neutrons. For the verification of the proposed method, MCNP simulations with the experimental system designed in this study were pursued using the polyethylene, iron, normal glass and the vitrified form. The results show that it can easily test neutron absorption ability using single absorber model. Also, from simulation results of single absorber and double absorbers model, it is verified that the proposed method can evaluate not only the direct thermal neutrons passing through materials, but also the scattered neutrons reflected to the materials. Therefore, the neutron absorption performances can be accurately estimated using the proposed method comparing with the conventional neutron attenuation test. It is expected that the proposed method can contribute to increase the reliability of the performance of neutron absorbers.

  12. A proposal on evaluation method of neutron absorption performance to substitute conventional neutron attenuation test

    International Nuclear Information System (INIS)

    Kim, Je Hyun; Shim, Chang Ho; Kim, Sung Hyun; Choe, Jung Hun; Cho, In Hak; Park, Hwan Seo; Park, Hyun Seo; Kim, Jung Ho; Kim, Yoon Ho

    2016-01-01

    For a verification of newly-developed neutron absorbers, one of guidelines on the qualification and acceptance of neutron absorbers is the neutron attenuation test. However, this approach can cause a problem for the qualifications that it cannot distinguish how the neutron attenuates from materials. In this study, an estimation method of neutron absorption performances for materials is proposed to detect both direct penetration and back-scattering neutrons. For the verification of the proposed method, MCNP simulations with the experimental system designed in this study were pursued using the polyethylene, iron, normal glass and the vitrified form. The results show that it can easily test neutron absorption ability using single absorber model. Also, from simulation results of single absorber and double absorbers model, it is verified that the proposed method can evaluate not only the direct thermal neutrons passing through materials, but also the scattered neutrons reflected to the materials. Therefore, the neutron absorption performances can be accurately estimated using the proposed method comparing with the conventional neutron attenuation test. It is expected that the proposed method can contribute to increase the reliability of the performance of neutron absorbers

  13. Proposal and Evaluation of Management Method for College Mechatronics Education Applying the Project Management

    Science.gov (United States)

    Ando, Yoshinobu; Eguchi, Yuya; Mizukawa, Makoto

    In this research, we proposed and evaluated a management method of college mechatronics education. We applied the project management to college mechatronics education. We practiced our management method to the seminar “Microcomputer Seminar” for 3rd grade students who belong to Department of Electrical Engineering, Shibaura Institute of Technology. We succeeded in management of Microcomputer Seminar in 2006. We obtained the good evaluation for our management method by means of questionnaire.

  14. A proposed impact assessment method for genetically modified plants (AS-GMP Method)

    International Nuclear Information System (INIS)

    Jesus-Hitzschky, Katia Regina Evaristo de; Silveira, Jose Maria F.J. da

    2009-01-01

    An essential step in the development of products based on biotechnology is an assessment of their potential economic impacts and safety, including an evaluation of the potential impact of transgenic crops and practices related to their cultivation on the environment and human or animal health. The purpose of this paper is to provide an assessment method to evaluate the impact of biotechnologies that uses quantifiable parameters and allows a comparative analysis between conventional technology and technologies using GMOs. This paper introduces a method to perform an impact analysis associated with the commercial release and use of genetically modified plants, the Assessment System GMP Method. The assessment is performed through indicators that are arranged according to their dimension criterion likewise: environmental, economic, social, capability and institutional approach. To perform an accurate evaluation of the GMP specific indicators related to genetic modification are grouped in common fields: genetic insert features, GM plant features, gene flow, food/feed field, introduction of the GMP, unexpected occurrences and specific indicators. The novelty is the possibility to include specific parameters to the biotechnology under assessment. In this case by case analysis the factors of moderation and the indexes are parameterized to perform an available assessment.

  15. Application of the Hybrid Simulation Method for the Full-Scale Precast Reinforced Concrete Shear Wall Structure

    Directory of Open Access Journals (Sweden)

    Zaixian Chen

    2018-02-01

    Full Text Available The hybrid simulation (HS testing method combines physical test and numerical simulation, and provides a viable alternative to evaluate the structural seismic performance. Most studies focused on the accuracy, stability and reliability of the HS method in the small-scale tests. It is a challenge to evaluate the seismic performance of a twelve-story pre-cast reinforced concrete shear-wall structure using this HS method which takes the full-scale bottom three-story structural model as the physical substructure and the elastic non-linear model as the numerical substructure. This paper employs an equivalent force control (EFC method with implicit integration algorithm to deal with the numerical integration of the equation of motion (EOM and the control of the loading device. Because of the arrangement of the test model, an elastic non-linear numerical model is used to simulate the numerical substructure. And non-subdivision strategy for the displacement inflection point of numerical substructure is used to easily realize the simulation of the numerical substructure and thus reduce the measured error. The parameters of the EFC method are calculated basing on analytical and numerical studies and used to the actual full-scale HS test. Finally, the accuracy and feasibility of the EFC-based HS method is verified experimentally through the substructure HS tests of the pre-cast reinforced concrete shear-wall structure model. And the testing results of the descending stage can be conveniently obtained from the EFC-based HS method.

  16. In-vitro evaluation of the accuracy of conventional and digital methods of obtaining full-arch dental impressions.

    Science.gov (United States)

    Ender, Andreas; Mehl, Albert

    2015-01-01

    To investigate the accuracy of conventional and digital impression methods used to obtain full-arch impressions by using an in-vitro reference model. Eight different conventional (polyether, POE; vinylsiloxanether, VSE; direct scannable vinylsiloxanether, VSES; and irreversible hydrocolloid, ALG) and digital (CEREC Bluecam, CER; CEREC Omnicam, OC; Cadent iTero, ITE; and Lava COS, LAV) full-arch impressions were obtained from a reference model with a known morphology, using a highly accurate reference scanner. The impressions obtained were then compared with the original geometry of the reference model and within each test group. A point-to-point measurement of the surface of the model using the signed nearest neighbour method resulted in a mean (10%-90%)/2 percentile value for the difference between the impression and original model (trueness) as well as the difference between impressions within a test group (precision). Trueness values ranged from 11.5 μm (VSE) to 60.2 μm (POE), and precision ranged from 12.3 μm (VSE) to 66.7 μm (POE). Among the test groups, VSE, VSES, and CER showed the highest trueness and precision. The deviation pattern varied with the impression method. Conventional impressions showed high accuracy across the full dental arch in all groups, except POE and ALG. Conventional and digital impression methods show differences regarding full-arch accuracy. Digital impression systems reveal higher local deviations of the full-arch model. Digital intraoral impression systems do not show superior accuracy compared to highly accurate conventional impression techniques. However, they provide excellent clinical results within their indications applying the correct scanning technique.

  17. Validation of a method for assessing resident physicians' quality improvement proposals.

    Science.gov (United States)

    Leenstra, James L; Beckman, Thomas J; Reed, Darcy A; Mundell, William C; Thomas, Kris G; Krajicek, Bryan J; Cha, Stephen S; Kolars, Joseph C; McDonald, Furman S

    2007-09-01

    Residency programs involve trainees in quality improvement (QI) projects to evaluate competency in systems-based practice and practice-based learning and improvement. Valid approaches to assess QI proposals are lacking. We developed an instrument for assessing resident QI proposals--the Quality Improvement Proposal Assessment Tool (QIPAT-7)-and determined its validity and reliability. QIPAT-7 content was initially obtained from a national panel of QI experts. Through an iterative process, the instrument was refined, pilot-tested, and revised. Seven raters used the instrument to assess 45 resident QI proposals. Principal factor analysis was used to explore the dimensionality of instrument scores. Cronbach's alpha and intraclass correlations were calculated to determine internal consistency and interrater reliability, respectively. QIPAT-7 items comprised a single factor (eigenvalue = 3.4) suggesting a single assessment dimension. Interrater reliability for each item (range 0.79 to 0.93) and internal consistency reliability among the items (Cronbach's alpha = 0.87) were high. This method for assessing resident physician QI proposals is supported by content and internal structure validity evidence. QIPAT-7 is a useful tool for assessing resident QI proposals. Future research should determine the reliability of QIPAT-7 scores in other residency and fellowship training programs. Correlations should also be made between assessment scores and criteria for QI proposal success such as implementation of QI proposals, resident scholarly productivity, and improved patient outcomes.

  18. Review of Dercum’s disease and proposal of diagnostic criteria, diagnostic methods, classification and management

    Directory of Open Access Journals (Sweden)

    Hansson Emma

    2012-04-01

    Full Text Available Abstract Definition and clinical picture We propose the minimal definition of Dercum’s disease to be generalised overweight or obesity in combination with painful adipose tissue. The associated symptoms in Dercum’s disease include fatty deposits, easy bruisability, sleep disturbances, impaired memory, depression, difficulty concentrating, anxiety, rapid heartbeat, shortness of breath, diabetes, bloating, constipation, fatigue, weakness and joint aches. Classification We suggest that Dercum’s disease is classified into: I. Generalised diffuse form A form with diffusely widespread painful adipose tissue without clear lipomas, II. Generalised nodular form - a form with general pain in adipose tissue and intense pain in and around multiple lipomas, and III. Localised nodular form - a form with pain in and around multiple lipomas IV. Juxtaarticular form - a form with solitary deposits of excess fat for example at the medial aspect of the knee. Epidemiology Dercum’s disease most commonly appears between the ages of 35 and 50 years and is five to thirty times more common in women than in men. The prevalence of Dercum’s disease has not yet been exactly established. Aetiology Proposed, but unconfirmed aetiologies include: nervous system dysfunction, mechanical pressure on nerves, adipose tissue dysfunction and trauma. Diagnosis and diagnostic methods Diagnosis is based on clinical criteria and should be made by systematic physical examination and thorough exclusion of differential diagnoses. Advisably, the diagnosis should be made by a physician with a broad experience of patients with painful conditions and knowledge of family medicine, internal medicine or pain management. The diagnosis should only be made when the differential diagnoses have been excluded. Differential diagnosis Differential diagnoses include: fibromyalgia, lipoedema, panniculitis, endocrine disorders, primary psychiatric disorders, multiple symmetric lipomatosis, familial

  19. Proximal gamma-ray spectroscopy to predict soil properties using windows and full-spectrum analysis methods.

    Science.gov (United States)

    Mahmood, Hafiz Sultan; Hoogmoed, Willem B; van Henten, Eldert J

    2013-11-27

    Fine-scale spatial information on soil properties is needed to successfully implement precision agriculture. Proximal gamma-ray spectroscopy has recently emerged as a promising tool to collect fine-scale soil information. The objective of this study was to evaluate a proximal gamma-ray spectrometer to predict several soil properties using energy-windows and full-spectrum analysis methods in two differently managed sandy loam fields: conventional and organic. In the conventional field, both methods predicted clay, pH and total nitrogen with a good accuracy (R2 ≥ 0.56) in the top 0-15 cm soil depth, whereas in the organic field, only clay content was predicted with such accuracy. The highest prediction accuracy was found for total nitrogen (R2 = 0.75) in the conventional field in the energy-windows method. Predictions were better in the top 0-15 cm soil depths than in the 15-30 cm soil depths for individual and combined fields. This implies that gamma-ray spectroscopy can generally benefit soil characterisation for annual crops where the condition of the seedbed is important. Small differences in soil structure (conventional vs. organic) cannot be determined. As for the methodology, we conclude that the energy-windows method can establish relations between radionuclide data and soil properties as accurate as the full-spectrum analysis method.

  20. Improved Full-Newton Step O(nL) Infeasible Interior-Point Method for Linear Optimization

    OpenAIRE

    Gu, G.; Mansouri, H.; Zangiabadi, M.; Bai, Y.Q.; Roos, C.

    2009-01-01

    We present several improvements of the full-Newton step infeasible interior-point method for linear optimization introduced by Roos (SIAM J. Optim. 16(4):1110–1136, 2006). Each main step of the method consists of a feasibility step and several centering steps. We use a more natural feasibility step, which targets the ?+-center of the next pair of perturbed problems. As for the centering steps, we apply a sharper quadratic convergence result, which leads to a slightly wider neighborhood for th...

  1. A Novel Choice Procedure of Magnetic Component Values for Phase Shifted Full Bridge Converters with a Variable Dead-Time Control Method

    Directory of Open Access Journals (Sweden)

    Lei Zhao

    2015-09-01

    Full Text Available Magnetic components are important parts of the phase shifted full bridge (PSFB converter. During the dead-time of switches located in the same leg, the converter can achieve zero-voltage-switching (ZVS by using the energies stored in magnetic components to discharge or charge the output capacitances of switches. Dead-time is usually calculated under a given set of pre-defined load condition which results in that the available energies are insufficient and ZVS capability is lost at light loads. In this paper, the PSFB converter is controlled by variable dead-time method and thus full advantage can be taken of the energies stored in magnetic components. Considering that dead-time has a great effect on ZVS, the relationship between available energies and magnetic component values is formulated by analyzing the equivalent circuits during dead-time intervals. Magnetic component values are chosen based on such relationship. The proposed choice procedure can make the available energies greater than the required energies for ZVS operation over a wide range of load conditions. Moreover, the burst mode control is adopted in order to reduce the standby power loss. Experimental results coincide with the theoretical analysis. The proposed method is a simple and practical solution to extend the ZVS range.

  2. Dynamic determination of modulus of elasticity of full-size wood composite panels using a vibration method

    Science.gov (United States)

    Cheng Guan; Houjiang Zhang; Lujing Zhou; Xiping Wang

    2015-01-01

    A vibration testing method based on free vibration theory in a ‘‘free–free” support condition was investigated for evaluating the modulus of elasticity (MOE) of full-size wood composite panels (WCPs). Vibration experiments were conducted on three types of WCPs (medium density fibreboard, particleboard, and plywood) to determine the dynamic MOE of the panels. Static...

  3. Proposal of a method for evaluating tsunami risk using response-surface methodology

    Science.gov (United States)

    Fukutani, Y.

    2017-12-01

    Information on probabilistic tsunami inundation hazards is needed to define and evaluate tsunami risk. Several methods for calculating these hazards have been proposed (e.g. Løvholt et al. (2012), Thio (2012), Fukutani et al. (2014), Goda et al. (2015)). However, these methods are inefficient, and their calculation cost is high, since they require multiple tsunami numerical simulations, therefore lacking versatility. In this study, we proposed a simpler method for tsunami risk evaluation using response-surface methodology. Kotani et al. (2016) proposed an evaluation method for the probabilistic distribution of tsunami wave-height using a response-surface methodology. We expanded their study and developed a probabilistic distribution of tsunami inundation depth. We set the depth (x1) and the slip (x2) of an earthquake fault as explanatory variables and tsunami inundation depth (y) as an object variable. Subsequently, tsunami risk could be evaluated by conducting a Monte Carlo simulation, assuming that the generation probability of an earthquake follows a Poisson distribution, the probability distribution of tsunami inundation depth follows the distribution derived from a response-surface, and the damage probability of a target follows a log normal distribution. We applied the proposed method to a wood building located on the coast of Tokyo Bay. We implemented a regression analysis based on the results of 25 tsunami numerical calculations and developed a response-surface, which was defined as y=ax1+bx2+c (a:0.2615, b:3.1763, c=-1.1802). We assumed proper probabilistic distribution for earthquake generation, inundation height, and vulnerability. Based on these probabilistic distributions, we conducted Monte Carlo simulations of 1,000,000 years. We clarified that the expected damage probability of the studied wood building is 22.5%, assuming that an earthquake occurs. The proposed method is therefore a useful and simple way to evaluate tsunami risk using a response

  4. 77 FR 24684 - Proposed Information Collection; Comment Request; 2013-2015 American Community Survey Methods...

    Science.gov (United States)

    2012-04-25

    ... proposed content changes. Thus, we need to test an alternative questionnaire design to accommodate additional content on the ACS mail questionnaire. In the 2013 ACS Questionnaire Design Test, we will study... in Puerto Rico. II. Method of Collection Questionnaire Design Test--Data collection for this test...

  5. Proposal for a Method for Business Model Performance Assessment: Toward an Experimentation Tool for Business Model Innovation

    Directory of Open Access Journals (Sweden)

    Antonio Batocchio

    2017-04-01

    Full Text Available The representation of business models has been recently widespread, especially in the pursuit of innovation. However, defining a company’s business model is sometimes limited to discussion and debates. This study observes the need for performance measurement so that business models can be data-driven. To meet this goal, the work proposed as a hypothesis the creation of a method that combines the practices of the Balanced Scorecard with a method of business models representation – the Business Model Canvas. Such a combination was based on study of conceptual adaptation, resulting in an application roadmap. A case study application was performed to check the functionality of the proposition, focusing on startup organizations. It was concluded that based on the performance assessment of the business model it is possible to propose the search for change through experimentation, a path that can lead to business model innovation.

  6. A Dissipation Gap Method for full-field measurement-based identification of elasto-plastic material parameters

    KAUST Repository

    Blaysat, Benoît

    2012-05-18

    Using enriched data such as displacement fields obtained from digital image correlation is a pathway to the local identification of material parameters. Up to now, most of the identification techniques for nonlinear models are based on Finite Element Updating Methods. This article explains how an appropriate use of the Dissipation Gap Method can help in this context and be an interesting alternative to these classical techniques. The Dissipation Gap Methods rely on the concept of error in dissipation that has been used mainly for the verification of finite element simulations. We provide here an original application of these founding developments to the identification of material parameters for nonlinear behaviors. The proposed technique and especially the main technical keypoint of building the admissible fields are described in detail. The approach is then illustrated through the identification of heterogeneous isotropic elasto-plastic properties. The basic numerical features highlighted through these simple examples demonstrate this approach to be a promising tool for nonlinear identification. © 2012 John Wiley & Sons, Ltd.

  7. Proposal for Requirement Validation Criteria and Method Based on Actor Interaction

    Science.gov (United States)

    Hattori, Noboru; Yamamoto, Shuichiro; Ajisaka, Tsuneo; Kitani, Tsuyoshi

    We propose requirement validation criteria and a method based on the interaction between actors in an information system. We focus on the cyclical transitions of one actor's situation against another and clarify observable stimuli and responses based on these transitions. Both actors' situations can be listed in a state transition table, which describes the observable stimuli or responses they send or receive. Examination of the interaction between both actors in the state transition tables enables us to detect missing or defective observable stimuli or responses. Typically, this method can be applied to the examination of the interaction between a resource managed by the information system and its user. As a case study, we analyzed 332 requirement defect reports of an actual system development project in Japan. We found that there were a certain amount of defects regarding missing or defective stimuli and responses, which can be detected using our proposed method if this method is used in the requirement definition phase. This means that we can reach a more complete requirement definition with our proposed method.

  8. A Proposed Method for Improving the Performance of P-Type GaAs IMPATTs

    Directory of Open Access Journals (Sweden)

    H. A. El-Motaafy

    2012-07-01

    Full Text Available A special waveform is proposed and assumed to be the optimum waveform for p-type GaAs IMPATTs. This waveform is deduced after careful and extensive study of the performance of these devices. The results presented here indicate the superiority of the performance of the IMPATTs driven by the proposed waveform over that obtained when the same IMPATTs are driven by the conventional sinusoidal waveform. These results are obtained using a full-scale computer simulation program that takes fully into account all the physical effects pertinent to IMPATT operation.  In this paper, it is indicated that the superiority of the proposed waveform is attributed to its ability to reduce the bad effects that usually degrade the IMPATT performance such as the space-charge effect and the drift-velocity dropping below saturation effect. The superiority is also attributed to the ability of the proposed waveform to improve the phase relationship between the terminal voltage and the induced current.Key Words: Computer-Aided Design, GaAs IMPATT, Microwave Engineering

  9. A method for projecting full-scale performance of CO/sub 2/ flooding in the Willard Unit

    International Nuclear Information System (INIS)

    Bilhartz, H.L.; Charlson, G.S.; Stalkup, F.I.; Miller, C.C.

    1985-01-01

    A non-producing CO/sub 2/ flood tertiary recovery test was recently completed in the Willard Unit of Wasson Field. Flood responses during waterflood and alternate injection of CO/sub 2/ and water were monitored at a logging observation well using compensated neutron and pulsed neutron logs. A pressure core was taken to measure residual oil saturations at the test conclusion. The overall objective of the testing was to obtain information for evaluating the potential for full-scale CO/sub 2/ flooding in the unit. Out method for making this evaluation involves: (1) defining CO/sub 2/ flood displacement efficiency and representing this efficiency in a miscible flood reservoir simulator; (2) defining a representative average reservoir description; and (3) projecting full-scale CO/sub 2/ flood performance with the simulator. The paper provides a status report on progress to assess CO/sub 2/ flooding potential for the Willard Unit in this manner

  10. Proposing Some New Ecliptics in New Testament Studies Enabled by Digital Humanities-Based Methods

    Directory of Open Access Journals (Sweden)

    James Libby

    2016-04-01

    Full Text Available “Fragmentation” is a well-worn watchword in contemporary biblical studies. But is endless fragmentation across the traditional domains of epistemology, methodology and hermeneutics the inevitable future for the postmodern exercise of biblical scholarship? In our view, multiple factors mitigate against such a future, but two command our attention here. First, digital humanities itself, through its principled use of corpora, databases and computer-based methods, seems to be remarkably capable of producing findings with high levels of face validity (interpretive agreement across multiple hermeneutical perspectives and communities. Second, and perhaps more subversively, there is a substantial body of practitioners that, per Kearney, actively question postmodernity’s impress as the final port of call for philosophy. For these practitioners deconstruction has become both indispensable — by delegitimizing hegemonies — but, in its own way, metanarratival by stultifying all other iterative, dialectical and critical processes that have historically motivated scholarship. Sensing this impasse, Kearney (1987, pp. 43-45 proposes a reimagining that is not only critical but that also embraces ποίησις, the possibility of optimistic, creative work. Such a stance within digital humanities would affirm that poietic events emerge not only through frictions and fragmentation (e.g. Kinder and McPherson 2014, pp. xiii-xviii but also through commonalties and convergence. Our approach here will be to demonstrate such a reimagining, rather than to argue for it, using two worked examples in the Greek New Testament (GNT. Those examples – digital humanities-enabled papyrology and digital humanities-enabled statistical linguistics – demonstrate ways in which the data of the text itself can be used to interrogate our perspectives and suggest that our perspectives must remain ever open to such inquiries. We conclude with a call for digital humanities to

  11. Cutting the Gordian Knot: A Proposal for Full State Funding of Elementary Education in Illinois. MacArthur/Spencer Series Number 13.

    Science.gov (United States)

    Arnold, Robert

    Property tax relief for the Illinois taxpayer, predicated on full state funding of elementary education, is advocated in this paper. A consequence of full state funding is the reduction of property taxes for education and creation of an educational income tax. Effects at the elementary level are equity and adequacy; at the secondary level, school…

  12. Determination of the oxidizing property: proposal of an alternative method based on differential scanning calorimetry

    International Nuclear Information System (INIS)

    Gigante, L.; Dellavedova, M.; Pasturenzi, C.; Lunghi, A.; Mattarella, M.; Cardillo, P.

    2008-01-01

    Determination of chemical-physical and hazardous properties of substances is a very important matter in the chemical industry, considering the growing attention of public opinion regarding safety and eco-compatibility aspects of products. In the present work, attention was focused on characterization of oxidizing properties. In case of solid compounds, the current method (Dir 84/449/CEE 6) compares the maximum combustion rate of the examined substance to the maximum combustion rate of a reference mixture. This method shows a lot of disvantages and does not provide a quantitative result. In the following work an alternative method, based on DSC measurements, is proposed for the determination of oxidizing properties. [it

  13. Full-scale demonstration of EBS construction technology I. Block, pellet and in-situ compaction method

    International Nuclear Information System (INIS)

    Toguri, Satohito; Asano, Hidekazu; Takao, Hajime; Matsuda, Takeshi; Amemiya, Kiyoshi

    2008-01-01

    (i) Bentonite Block: Applicability of manufacturing technology of buffer material was verified by manufacturing of full scale bentonite ring which consists of one-eight (1/8) dividing block (Outside Diameter (OD): 2.220 mm H: 300 mm). Density characteristic, dimension and scale effect, which were considered the tunnel environment under transportation, were evaluated. Vacuum suction technology was selected as handling technology for the ring. Hoisting characteristic of vacuum suction technology was presented through evaluation of the mechanical property of buffer material, the friction between blocks, etc. by using a full-scale bentonite ring (OD 2.200 mm, H 300 mm). And design of bentonite block and emplacement equipment were presented in consideration of manufacturability of the block, stability of handling and improvement of emplacement efficiency. (ii) Bentonite Pellet Filling: Basic characteristics such as water penetration, swelling and thermal conductivity of various kinds of bentonite pellet were collected by laboratory scale tests. Applicability of pellet filling technology was evaluated by horizontal filling test using a simulated full-scale drift tunnel (OD 2.200 mm, L 6 m) . Filling density, grain size distribution, etc. were also measured. (iii) In-Situ Compaction of Bentonite: Dynamic compaction method (heavy weight fall method) was selected as in-situ compaction technology. Compacting examination which used a full scale disposal pit (OD 2.360 mm) was carried out. Basic specification of compacting equipment and applicability of in-situ compaction technology were presented. Density, density distribution of buffer material and energy acted on the wall of the pit, were also measured. (author)

  14. Estimation of body fluids with bioimpedance spectroscopy: state of the art methods and proposal of novel methods

    International Nuclear Information System (INIS)

    Buendia, R; Seoane, F; Lindecrantz, K; Bosaeus, I; Gil-Pita, R; Johannsson, G; Ellegård, L; Ward, L C

    2015-01-01

    Determination of body fluids is a useful common practice in determination of disease mechanisms and treatments. Bioimpedance spectroscopy (BIS) methods are non-invasive, inexpensive and rapid alternatives to reference methods such as tracer dilution. However, they are indirect and their robustness and validity are unclear. In this article, state of the art methods are reviewed, their drawbacks identified and new methods are proposed. All methods were tested on a clinical database of patients receiving growth hormone replacement therapy. Results indicated that most BIS methods are similarly accurate (e.g.  <  0.5   ±   3.0% mean percentage difference for total body water) for estimation of body fluids. A new model for calculation is proposed that performs equally well for all fluid compartments (total body water, extra- and intracellular water). It is suggested that the main source of error in extracellular water estimation is due to anisotropy, in total body water estimation to the uncertainty associated with intracellular resistivity and in determination of intracellular water a combination of both. (paper)

  15. Probabilistic methods of optimization of scheduled tests for heat equipment of safety systems of reactor at full power

    International Nuclear Information System (INIS)

    Bilej, D.V.; Fridman, N.A.; Kolykhanov, V.N.; Skalozubov, V.I.

    2004-01-01

    This article generalises the basic results of a long-term teamwork with respect to a scientific and technical substantiation of perfection of the regulations of safe operation power units with VVER. This perfection is concerning a periodicity and volumes of tests of safety systems when a reactor works at full power. The article shows that the application of the probabilistic approaches connected to minimisation of a risk criterion function is an effective methodical base for the optimisation. For certain safety systems of serial power units with VVER 1000 the results of calculated substantiations are presented

  16. Evaluation of protection factors provided by full-face masks using man-test method at workplace

    International Nuclear Information System (INIS)

    Izumi, Yukio; Kinouchi, Nobuyuki; Ikezawa, Yoshio.

    1994-01-01

    From a practical angle of view to estimate the protection factors (PFs) provided by full-face masks, a number of protection factors were measured with a man-test apparatus just before the wearers started to do radiation work in radiation controlled area. PFs of the total number of 2,279 cases were measured under five simulated working conditions. The measured PFs were widely distributed from 2.3 to 6,700. About 95% of workers obtained PFs more than 50, and about 64% showed much higher PFs more than 1,000 due to good fitting. In the case of some persons, the measured PFs irregularly varied and changed to a large degree. This method is a reliable technique that has been confirmed to protect unexpected internal exposure. From the results obtained, the method should be necessary to provide a better mask and higher PF for each worker. (author)

  17. Full-Color LCD Microdisplay System Based on OLED Backlight Unit and Field-Sequential Color Driving Method

    Directory of Open Access Journals (Sweden)

    Sungho Woo

    2011-01-01

    Full Text Available We developed a single-panel LCD microdisplay system using a field-sequential color (FSC driving method and an organic light-emitting diode (OLED as a backlight unit (BLU. The 0.76′′ OLED BLU with red, green, and blue (RGB colors was fabricated by a conventional UV photolithography patterning process and by vacuum deposition of small molecule organic layers. The field-sequential driving frequency was set to 255 Hz to allow each of the RGB colors to be generated without color mixing at the given display frame rate. A prototype FSC LCD microdisplay system consisting of a 0.7′′ LCD microdisplay panel and the 0.76′′ OLED BLU successfully exhibited color display and moving picture images using the FSC driving method.

  18. Proposed waste form performance criteria and testing methods for low-level mixed waste

    International Nuclear Information System (INIS)

    Franz, E.M.; Fuhrmann, M.; Bowerman, B.

    1995-01-01

    Proposed waste form performance criteria and testing methods were developed as guidance in judging the suitability of solidified waste as a physico-chemical barrier to releases of radionuclides and RCRA regulated hazardous components. The criteria follow from the assumption that release of contaminants by leaching is the single most important property for judging the effectiveness of a waste form. A two-tier regimen is proposed. The first tier consists of a leach test designed to determine the net, forward leach rate of the solidified waste and a leach test required by the Environmental Protection Agency (EPA). The second tier of tests is to determine if a set of stresses (i.e., radiation, freeze-thaw, wet-dry cycling) on the waste form adversely impacts its ability to retain contaminants and remain physically intact. In the absence of site-specific performance assessments (PA), two generic modeling exercises are described which were used to calculate proposed acceptable leachates

  19. A method proposal for cumulative environmental impact assessment based on the landscape vulnerability evaluation

    International Nuclear Information System (INIS)

    Pavlickova, Katarina; Vyskupova, Monika

    2015-01-01

    Cumulative environmental impact assessment deals with the occasional use in practical application of environmental impact assessment process. The main reasons are the difficulty of cumulative impact identification caused by lack of data, inability to measure the intensity and spatial effect of all types of impacts and the uncertainty of their future evolution. This work presents a method proposal to predict cumulative impacts on the basis of landscape vulnerability evaluation. For this purpose, qualitative assessment of landscape ecological stability is conducted and major vulnerability indicators of environmental and socio-economic receptors are specified and valuated. Potential cumulative impacts and the overall impact significance are predicted quantitatively in modified Argonne multiple matrixes while considering the vulnerability of affected landscape receptors and the significance of impacts identified individually. The method was employed in the concrete environmental impact assessment process conducted in Slovakia. The results obtained in this case study reflect that this methodology is simple to apply, valid for all types of impacts and projects, inexpensive and not time-consuming. The objectivity of the partial methods used in this procedure is improved by quantitative landscape ecological stability evaluation, assignment of weights to vulnerability indicators based on the detailed characteristics of affected factors, and grading impact significance. - Highlights: • This paper suggests a method proposal for cumulative impact prediction. • The method includes landscape vulnerability evaluation. • The vulnerability of affected receptors is determined by their sensitivity. • This method can increase the objectivity of impact prediction in the EIA process

  20. Proposal of evaluation method of tsunami wave pressure using 2D depth-integrated flow simulation

    International Nuclear Information System (INIS)

    Arimitsu, Tsuyoshi; Ooe, Kazuya; Kawasaki, Koji

    2012-01-01

    To design and construct land structures resistive to tsunami force, it is most essential to evaluate tsunami pressure quantitatively. The existing hydrostatic formula, in general, tended to underestimate tsunami wave pressure under the condition of inundation flow with large Froude number. Estimation method of tsunami pressure acting on a land structure was proposed using inundation depth and horizontal velocity at the front of the structure, which were calculated employing a 2D depth-integrated flow model based on the unstructured grid system. The comparison between the numerical and experimental results revealed that the proposed method could reasonably reproduce the vertical distribution of the maximum tsunami pressure as well as the time variation of the tsunami pressure exerting on the structure. (author)

  1. A proposed safety assurance method and its application to the fusion experimental reactor

    International Nuclear Information System (INIS)

    Okazaki, T.; Seki, Y.; Inabe, T.; Aoki, I.

    1995-01-01

    Importance categorization and hazard identification methods have been proposed for a fusion experimental reactor. A parameter, the system index, is introduced in the categorization method. The relative importance of systems with safety functions can be classified by the largeness of the system index and whether or not the system acts as a boundary for radioactive materials. This categorization can be used as the basic principle in determining structure design assessment, seismic design criteria etc. For the hazard identification the system time energy matrix is proposed, where the time and spatial distributions of hazard energies are used. This approach is formulated more systematically than an ad-hoc identification of hazard events and it is useful to select design basis events which are employed in the assessment of safety designs. (orig.)

  2. Proposed Project Selection Method for Human Support Research and Technology Development (HSR&TD)

    Science.gov (United States)

    Jones, Harry

    2005-01-01

    The purpose of HSR&TD is to deliver human support technologies to the Exploration Systems Mission Directorate (ESMD) that will be selected for future missions. This requires identifying promising candidate technologies and advancing them in technology readiness until they are acceptable. HSR&TD must select an may of technology development projects, guide them, and either terminate or continue them, so as to maximize the resulting number of usable advanced human support technologies. This paper proposes an effective project scoring methodology to support managing the HSR&TD project portfolio. Researchers strongly disagree as to what are the best technology project selection methods, or even if there are any proven ones. Technology development is risky and outstanding achievements are rare and unpredictable. There is no simple formula for success. Organizations that are satisfied with their project selection approach typically use a mix of financial, strategic, and scoring methods in an open, established, explicit, formal process. This approach helps to build consensus and develop management insight. It encourages better project proposals by clarifying the desired project attributes. We propose a project scoring technique based on a method previously used in a federal laboratory and supported by recent research. Projects are ranked by their perceived relevance, risk, and return - a new 3 R's. Relevance is the degree to which the project objective supports the HSR&TD goal of developing usable advanced human support technologies. Risk is the estimated probability that the project will achieve its specific objective. Return is the reduction in mission life cycle cost obtained if the project is successful. If the project objective technology performs a new function with no current cost, its return is the estimated cash value of performing the new function. The proposed project selection scoring method includes definitions of the criteria, a project evaluation

  3. Proposal of Constraints Analysis Method Based on Network Model for Task Planning

    Science.gov (United States)

    Tomiyama, Tomoe; Sato, Tatsuhiro; Morita, Toyohisa; Sasaki, Toshiro

    Deregulation has been accelerating several activities toward reengineering business processes, such as railway through service and modal shift in logistics. Making those activities successful, business entities have to regulate new business rules or know-how (we call them ‘constraints’). According to the new constraints, they need to manage business resources such as instruments, materials, workers and so on. In this paper, we propose a constraint analysis method to define constraints for task planning of the new business processes. To visualize each constraint's influence on planning, we propose a network model which represents allocation relations between tasks and resources. The network can also represent task ordering relations and resource grouping relations. The proposed method formalizes the way of defining constraints manually as repeatedly checking the network structure and finding conflicts between constraints. Being applied to crew scheduling problems shows that the method can adequately represent and define constraints of some task planning problems with the following fundamental features, (1) specifying work pattern to some resources, (2) restricting the number of resources for some works, (3) requiring multiple resources for some works, (4) prior allocation of some resources to some works and (5) considering the workload balance between resources.

  4. Comparison among four proposed direct blood culture microbial identification methods using MALDI-TOF MS.

    Science.gov (United States)

    Bazzi, Ali M; Rabaan, Ali A; El Edaily, Zeyad; John, Susan; Fawarah, Mahmoud M; Al-Tawfiq, Jaffar A

    Matrix-assisted laser desorption-ionization time-of-flight (MALDI-TOF) mass spectrometry facilitates rapid and accurate identification of pathogens, which is critical for sepsis patients. In this study, we assessed the accuracy in identification of both Gram-negative and Gram-positive bacteria, except for Streptococcus viridans, using four rapid blood culture methods with Vitek MALDI-TOF-MS. We compared our proposed lysis centrifugation followed by washing and 30% acetic acid treatment method (method 2) with two other lysis centrifugation methods (washing and 30% formic acid treatment (method 1); 100% ethanol treatment (method 3)), and picking colonies from 90 to 180min subculture plates (method 4). Methods 1 and 2 identified all organisms down to species level with 100% accuracy, except for Streptococcus viridans, Streptococcus pyogenes, Enterobacter cloacae and Proteus vulgaris. The latter two were identified to genus level with 100% accuracy. Each method exhibited excellent accuracy and precision in terms of identification to genus level with certain limitations. Copyright © 2016 King Saud Bin Abdulaziz University for Health Sciences. Published by Elsevier Ltd. All rights reserved.

  5. A Proposal on the Quantitative Homogeneity Analysis Method of SEM Images for Material Inspections

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Song Hyun; Kim, Jong Woo; Shin, Chang Ho [Hanyang University, Seoul (Korea, Republic of); Choi, Jung-Hoon; Cho, In-Hak; Park, Hwan Seo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    A scanning electron microscope (SEM) is a method to inspect the surface microstructure of materials. The SEM uses electron beams for imaging high magnifications of material surfaces; therefore, various chemical analyses can be performed from the SEM images. Therefore, it is widely used for the material inspection, chemical characteristic analysis, and biological analysis. For the nuclear criticality analysis field, it is an important parameter to check the homogeneity of the compound material for using it in the nuclear system. In our previous study, the SEM was tried to use for the homogeneity analysis of the materials. In this study, a quantitative homogeneity analysis method of SEM images is proposed for the material inspections. The method is based on the stochastic analysis method with the information of the grayscales of the SEM images.

  6. Proposal for outline of training and evaluation method for non-technical skills

    International Nuclear Information System (INIS)

    Nagasaka, Akihiko; Shibue, Hisao

    2015-01-01

    The purpose of this study is to systematize measures for improvement of emergency response capability focused on non-technical skills. As the results of investigation of some emergency training in nuclear power plant and referring to CRM training, following two issues were picked up. 1) Lack of practical training method for improvement of non-technical skills. 2) Lack of evaluation method of non-technical skills. Then, based on these 7 non-technical skills 'situational awareness' 'decision making' 'communication' 'teamworking' 'leadership' 'managing stress' 'coping with fatigue' are promotion factors to improve emergency response capability, we propose practical training method for each non-technical skill. Also we give example of behavioral markers as evaluation factor, and indicate approaches to introduce the evaluation method of non-technical skills. (author)

  7. A Proposal on the Quantitative Homogeneity Analysis Method of SEM Images for Material Inspections

    International Nuclear Information System (INIS)

    Kim, Song Hyun; Kim, Jong Woo; Shin, Chang Ho; Choi, Jung-Hoon; Cho, In-Hak; Park, Hwan Seo

    2015-01-01

    A scanning electron microscope (SEM) is a method to inspect the surface microstructure of materials. The SEM uses electron beams for imaging high magnifications of material surfaces; therefore, various chemical analyses can be performed from the SEM images. Therefore, it is widely used for the material inspection, chemical characteristic analysis, and biological analysis. For the nuclear criticality analysis field, it is an important parameter to check the homogeneity of the compound material for using it in the nuclear system. In our previous study, the SEM was tried to use for the homogeneity analysis of the materials. In this study, a quantitative homogeneity analysis method of SEM images is proposed for the material inspections. The method is based on the stochastic analysis method with the information of the grayscales of the SEM images

  8. Comments and Remarks over Classic Linear Loop-Gain Method for Oscillator Design and Analysis. New Proposed Method Based on NDF/RRT

    Directory of Open Access Journals (Sweden)

    J. L. Jimenez-Martin

    2012-04-01

    Full Text Available Present paper describes a new method for designing oscillators based on the Normalized Determinant Function (NDF and Return Relations (RRT . First a review of the loop-gain method will be performed, showing pros, cons and including some examples for exploring wrong so- lutions provided by this method. Wrong solutions, because some conditions have to be previously fulfilled in order to obtain right ones, which will be described and finally, demonstrate that NDF analysis is necessary, including Return Relations (RRT usefulness, which in fact are related with the True Loop-Gain. Finally concluding this paper, steps for oscillator design and analysis, using the proposed NDF/RRT method will be presented, compared to wrong previous solutions pointing out new accuracy achieved on oscillation frequency and QL prediction. Also, more new examples, of plane reference oscillators (Z/Y/rho, will be added for which loop gain method application is clearly difficult or even impossible, solving them with the new proposed NDF/RRT method.

  9. Accelerated one-step generation of full-color holographic videos using a color-tunable novel-look-up-table method for holographic three-dimensional television broadcasting

    Science.gov (United States)

    Kim, Seung-Cheol; Dong, Xiao-Bin; Kim, Eun-Soo

    2015-09-01

    A color-tunable novel-look-up-table (CT-NLUT) for fast one-step calculation of full-color computer-generated holograms is proposed. The proposed method is composed of four principal fringe patterns (PFPs) such as a baseline, a depth-compensating and two color-compensating PFPs. CGH patterns for one color are calculated by combined use of baseline-PFP and depth-compensating-PFP and from them, those for two other colors are generated by being multiplied by the corresponding color-compensating-PFPs. color-compensating-PFPs compensate for differences in the wavelength between two colors based on their unique achromatic thin-lens properties, enabling transformation of one-color CGH pattern into those for other colors. This color-conversion property of the proposed method enables simultaneous generation of full color-CGH patterns, resulting in a significant reduction of the full color-CGH calculation time. Experimental results with test scenario show that the full color-CGH calculation time of the proposed CT-NLUT has been reduced by 45.10%, compared to the conventional NLUT. It has been further reduced by 96.01% when a data compression algorithm, called temporal redundancy-based NLUT, was used together, which means 25-fold reduction of its full color-CGH calculation time. Successful computational and optical reconstructions of full color-CGH patterns confirm the feasibility of the proposed method.

  10. The Linearized Bregman Method for Frugal Full-waveform Inversion with Compressive Sensing and Sparsity-promoting

    Science.gov (United States)

    Chai, Xintao; Tang, Genyang; Peng, Ronghua; Liu, Shaoyong

    2018-03-01

    Full-waveform inversion (FWI) reconstructs the subsurface properties from acquired seismic data via minimization of the misfit between observed and simulated data. However, FWI suffers from considerable computational costs resulting from the numerical solution of the wave equation for each source at each iteration. To reduce the computational burden, constructing supershots by combining several sources (aka source encoding) allows mitigation of the number of simulations at each iteration, but it gives rise to crosstalk artifacts because of interference between the individual sources of the supershot. A modified Gauss-Newton FWI (MGNFWI) approach showed that as long as the difference between the initial and true models permits a sparse representation, the ℓ _1-norm constrained model updates suppress subsampling-related artifacts. However, the spectral-projected gradient ℓ _1 (SPGℓ _1) algorithm employed by MGNFWI is rather complicated that makes its implementation difficult. To facilitate realistic applications, we adapt a linearized Bregman (LB) method to sparsity-promoting FWI (SPFWI) because of the efficiency and simplicity of LB in the framework of ℓ _1-norm constrained optimization problem and compressive sensing. Numerical experiments performed with the BP Salt model, the Marmousi model and the BG Compass model verify the following points. The FWI result with LB solving ℓ _1-norm sparsity-promoting problem for the model update outperforms that generated by solving ℓ _2-norm problem in terms of crosstalk elimination and high-fidelity results. The simpler LB method performs comparably and even superiorly to the complicated SPGℓ _1 method in terms of computational efficiency and model quality, making the LB method a viable alternative for realistic implementations of SPFWI.

  11. Study on the ultrasonic inspection method using the full matrix capture for the in service railway wheel

    Energy Technology Data Exchange (ETDEWEB)

    Peng, Jianping; Wang, Li; Zhang, Yu; Gao, Xiaorong; Wang, Zeyong; Peng, Chaoyong [NDT Research Center, School of Physical Science and Technology, Southwest Jiaotong University, Chengdu 610031 (China)

    2014-02-18

    The quality of wheel is especially important for the safety of high speed railway. In this paper, a new ultrasonic array inspection method, the Full Matrix Capture (FMC) has been studied and applied to the high speed railway wheel inspection, especially in the wheel web from the tread. Firstly, the principle of FMC and TFM algorithm is discussed, and then the new optimization is applied to the standard FMC; Secondly the fundamentals of optimization is described in detail and the performance is analyzed. Finally, the experiment has been built with a standard phased array block and railway wheel, and then the testing results are discussed and analyzed. It is demonstrated that this change for the ultrasonic data acquisition and image reconstruction has higher efficiency and lower cost comparing to the FMC's procedure.

  12. Full-Wave Analysis of Traveling-Wave Field-Effect Transistors Using Finite-Difference Time-Domain Method

    Directory of Open Access Journals (Sweden)

    Koichi Narahara

    2012-01-01

    Full Text Available Nonlinear transmission lines, which define transmission lines periodically loaded with nonlinear devices such as varactors, diodes, and transistors, are modeled in the framework of finite-difference time-domain (FDTD method. Originally, some root-finding routine is needed to evaluate the contributions of nonlinear device currents appropriately to the temporally advanced electrical fields. Arbitrary nonlinear transmission lines contain large amount of nonlinear devices; therefore, it costs too much time to complete calculations. To reduce the calculation time, we recently developed a simple model of diodes to eliminate root-finding routines in an FDTD solver. Approximating the diode current-voltage relation by a piecewise-linear function, an extended Ampere's law is solved in a closed form for the time-advanced electrical fields. In this paper, we newly develop an FDTD model of field-effect transistors (FETs, together with several numerical examples that demonstrate pulse-shortening phenomena in a traveling-wave FET.

  13. Centroid and full-width at half maximum uncertainties of histogrammed data with an underlying Gaussian distribution -- The moments method

    International Nuclear Information System (INIS)

    Valentine, J.D.; Rana, A.E.

    1996-01-01

    The effect of approximating a continuous Gaussian distribution with histogrammed data are studied. The expressions for theoretical uncertainties in centroid and full-width at half maximum (FWHM), as determined by calculation of moments, are derived using the error propagation method for a histogrammed Gaussian distribution. The results are compared with the corresponding pseudo-experimental uncertainties for computer-generated histogrammed Gaussian peaks to demonstrate the effect of binning the data. It is shown that increasing the number of bins in the histogram improves the continuous distribution approximation. For example, a FWHM ≥ 9 and FWHM ≥ 12 bins are needed to reduce the pseudo-experimental standard deviation of FWHM to within ≥5% and ≥1%, respectively, of the theoretical value for a peak containing 10,000 counts. In addition, the uncertainties in the centroid and FWHM as a function of peak area are studied. Finally, Sheppard's correction is applied to partially correct for the binning effect

  14. Projection potentials and angular momentum convergence of total energies in the full-potential Korringa–Kohn–Rostoker method

    International Nuclear Information System (INIS)

    Zeller, Rudolf

    2013-01-01

    Although the full-potential Korringa–Kohn–Rostoker Green function method yields accurate results for many physical properties, the convergence of calculated total energies with respect to the angular momentum cutoff is usually considered to be less satisfactory. This is surprising because accurate single-particle energies are expected if they are calculated by Lloyd’s formula and because accurate densities and hence accurate double-counting energies should result from the total energy variational principle. It is shown how the concept of projection potentials can be used as a tool to analyse the convergence behaviour. The key factor blocking fast convergence is identified and it is illustrated how total energies can be improved with only a modest increase of computing time. (paper)

  15. A rapid method for simultaneously determining ethanol and methanol content in wines by full evaporation headspace gas chromatography.

    Science.gov (United States)

    Zhang, Chun-Yun; Lin, Neng-Biao; Chai, Xin-Sheng; Zhong-Li; Barnes, Donald G

    2015-09-15

    This work reports on a full evaporation headspace gas chromatographic (FE HS-GC) method for simultaneously determining the ethanol (EtOH) and methanol (MeOH) content in wines. A small sample (10μL) was placed in a headspace sample vial, and a near-complete mass transfer of ethanol and methanol from the liquid sample to the vapor phase was obtained within three minutes at a temperature of 105°C, which allowed the measurement of the EtOH and MeOH content in the sample by GC. The results showed excellent precision and accuracy, as shown by the reproducibilities of 1.02% and 2.11% for EtOH and MeOH, respectively, and recoveries that ranged from 96.1% to 104% for both alcohols. The method is efficient, accurate and suitable for the determination of EtOH and MeOH in wine production and quality control. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. European experiences of the proposed ASTM test method for crack arrest toughness of ferritic materials

    International Nuclear Information System (INIS)

    Jutla, T.; Lidbury, D.P.G.; Ziebs, J.; Zimmermann, C.

    1986-01-01

    The proposed ASTM test method for measuring the crack arrest toughness of ferritic materials using wedge-loaded, side-grooved, compact specimens was applied to three steels: A514 bridge steel, A588 bridge steel, and A533B pressure vessel steel. Five sets of results from different laboratories are discussed here. Notches were prepared by spark erosion, although root radii varied from ∝0.1-1.5 mm. Although fast fractures were successfully initiated, arrest did not occur in a significant number of cases. The results showed no obvious dependence of crack arrest toughness, K a , (determined by a static analysis) on crack initiation toughness, K 0 . It was found that K a decreases markedly with increasing crack jump distance. A limited amount of further work on smaller specimens of the A533B steel showed that lower K a values tended to be recorded. It is concluded that a number of points relating to the proposed test method and notch preparation are worthy of further consideration. It is pointed out that the proposed validity criteria may screen out lower bound data. Nevertheless, for present practical purposes, K a values may be regarded as useful in providing an estimate of arrest toughness - although not necessarily a conservative estimate. (orig./HP)

  17. Proposal for a Full-Scale Prototype Single-Phase Liquid Argon Time Projection Chamber and Detector Beam Test at CERN

    CERN Document Server

    Kutter, T

    2015-01-01

    The Deep Underground Neutrino Experiment (DUNE) will use a large liquid argon (LAr) detector to measure the CP violating phase, determine the neutrino mass hier- archy and perform precision tests of the three-flavor paradigm in long-baseline neutrino oscillations. The detector will consist of four modules each with a fiducial mass of 10 kt of LAr and due to its unprecedented size will allow sensitive searches for proton decay and the detection and measurement of electron neutrinos from core collapse supernovae [1]. The first 10 kt module will use single-phase LAr detection technique and be itself modular in design. The successful manufacturing, installation and operation of several full-scale detector components in a suitable configuration represents a critical engineering milestone prior to the construction and operation of the first full 10 kt DUNE detector module at the SURF underground site. A charged particle beam test of a prototype detector will provide critical calibration measurements as well as inva...

  18. A proposed architecture and method of operation for improving the protection of privacy and confidentiality in disease registers

    Directory of Open Access Journals (Sweden)

    Churches Tim

    2003-01-01

    Full Text Available Abstract Background Disease registers aim to collect information about all instances of a disease or condition in a defined population of individuals. Traditionally methods of operating disease registers have required that notifications of cases be identified by unique identifiers such as social security number or national identification number, or by ensembles of non-unique identifying data items, such as name, sex and date of birth. However, growing concern over the privacy and confidentiality aspects of disease registers may hinder their future operation. Technical solutions to these legitimate concerns are needed. Discussion An alternative method of operation is proposed which involves splitting the personal identifiers from the medical details at the source of notification, and separately encrypting each part using asymmetrical (public key cryptographic methods. The identifying information is sent to a single Population Register, and the medical details to the relevant disease register. The Population Register uses probabilistic record linkage to assign a unique personal identification (UPI number to each person notified to it, although not necessarily everyone in the entire population. This UPI is shared only with a single trusted third party whose sole function is to translate between this UPI and separate series of personal identification numbers which are specific to each disease register. Summary The system proposed would significantly improve the protection of privacy and confidentiality, while still allowing the efficient linkage of records between disease registers, under the control and supervision of the trusted third party and independent ethics committees. The proposed architecture could accommodate genetic databases and tissue banks as well as a wide range of other health and social data collections. It is important that proposals such as this are subject to widespread scrutiny by information security experts, researchers and

  19. GafChromic EBT film dosimetry with flatbed CCD scanner: a novel background correction method and full dose uncertainty analysis.

    Science.gov (United States)

    Saur, Sigrun; Frengen, Jomar

    2008-07-01

    Film dosimetry using radiochromic EBT film in combination with a flatbed charge coupled device scanner is a useful method both for two-dimensional verification of intensity-modulated radiation treatment plans and for general quality assurance of treatment planning systems and linear accelerators. Unfortunately, the response over the scanner area is nonuniform, and when not corrected for, this results in a systematic error in the measured dose which is both dose and position dependent. In this study a novel method for background correction is presented. The method is based on the subtraction of a correction matrix, a matrix that is based on scans of films that are irradiated to nine dose levels in the range 0.08-2.93 Gy. Because the response of the film is dependent on the film's orientation with respect to the scanner, correction matrices for both landscape oriented and portrait oriented scans were made. In addition to the background correction method, a full dose uncertainty analysis of the film dosimetry procedure was performed. This analysis takes into account the fit uncertainty of the calibration curve, the variation in response for different film sheets, the nonuniformity after background correction, and the noise in the scanned films. The film analysis was performed for film pieces of size 16 x 16 cm, all with the same lot number, and all irradiations were done perpendicular onto the films. The results show that the 2-sigma dose uncertainty at 2 Gy is about 5% and 3.5% for landscape and portrait scans, respectively. The uncertainty gradually increases as the dose decreases, but at 1 Gy the 2-sigma dose uncertainty is still as good as 6% and 4% for landscape and portrait scans, respectively. The study shows that film dosimetry using GafChromic EBT film, an Epson Expression 1680 Professional scanner and a dedicated background correction technique gives precise and accurate results. For the purpose of dosimetric verification, the calculated dose distribution

  20. GafChromic EBT film dosimetry with flatbed CCD scanner: A novel background correction method and full dose uncertainty analysis

    International Nuclear Information System (INIS)

    Saur, Sigrun; Frengen, Jomar

    2008-01-01

    Film dosimetry using radiochromic EBT film in combination with a flatbed charge coupled device scanner is a useful method both for two-dimensional verification of intensity-modulated radiation treatment plans and for general quality assurance of treatment planning systems and linear accelerators. Unfortunately, the response over the scanner area is nonuniform, and when not corrected for, this results in a systematic error in the measured dose which is both dose and position dependent. In this study a novel method for background correction is presented. The method is based on the subtraction of a correction matrix, a matrix that is based on scans of films that are irradiated to nine dose levels in the range 0.08-2.93 Gy. Because the response of the film is dependent on the film's orientation with respect to the scanner, correction matrices for both landscape oriented and portrait oriented scans were made. In addition to the background correction method, a full dose uncertainty analysis of the film dosimetry procedure was performed. This analysis takes into account the fit uncertainty of the calibration curve, the variation in response for different film sheets, the nonuniformity after background correction, and the noise in the scanned films. The film analysis was performed for film pieces of size 16x16 cm, all with the same lot number, and all irradiations were done perpendicular onto the films. The results show that the 2-sigma dose uncertainty at 2 Gy is about 5% and 3.5% for landscape and portrait scans, respectively. The uncertainty gradually increases as the dose decreases, but at 1 Gy the 2-sigma dose uncertainty is still as good as 6% and 4% for landscape and portrait scans, respectively. The study shows that film dosimetry using GafChromic EBT film, an Epson Expression 1680 Professional scanner and a dedicated background correction technique gives precise and accurate results. For the purpose of dosimetric verification, the calculated dose distribution can

  1. Proposal for an Evaluation Method for the Performance of Work Procedures.

    Science.gov (United States)

    Mohammed, Mouda; Mébarek, Djebabra; Wafa, Boulagouas; Makhlouf, Chati

    2016-12-01

    Noncompliance of operators with work procedures is a recurrent problem. This human behavior has been said to be situational and studied by many different approaches (ergonomic and others), which consider the noncompliance with work procedures to be obvious and seek to analyze its causes as well as consequences. The object of the proposed method is to solve this problem by focusing on the performance of work procedures and ensuring improved performance on a continuous basis. This study has multiple results: (1) assessment of the work procedures' performance by a multicriteria approach; (2) the use of a continuous improvement approach as a framework for the sustainability of the assessment method of work procedures' performance; and (3) adaptation of the Stop-Card as a facilitator support for continuous improvement of work procedures. The proposed method emphasizes to put in value the inputs of continuous improvement of the work procedures in relation with the conventional approaches which adopt the obvious evidence of the noncompliance to the working procedures and seek to analyze the cause-effect relationships related to this unacceptable phenomenon, especially in strategic industry.

  2. Using a fuzzy comprehensive evaluation method to determine product usability: A proposed theoretical framework.

    Science.gov (United States)

    Zhou, Ronggang; Chan, Alan H S

    2017-01-01

    In order to compare existing usability data to ideal goals or to that for other products, usability practitioners have tried to develop a framework for deriving an integrated metric. However, most current usability methods with this aim rely heavily on human judgment about the various attributes of a product, but often fail to take into account of the inherent uncertainties in these judgments in the evaluation process. This paper presents a universal method of usability evaluation by combining the analytic hierarchical process (AHP) and the fuzzy evaluation method. By integrating multiple sources of uncertain information during product usability evaluation, the method proposed here aims to derive an index that is structured hierarchically in terms of the three usability components of effectiveness, efficiency, and user satisfaction of a product. With consideration of the theoretical basis of fuzzy evaluation, a two-layer comprehensive evaluation index was first constructed. After the membership functions were determined by an expert panel, the evaluation appraisals were computed by using the fuzzy comprehensive evaluation technique model to characterize fuzzy human judgments. Then with the use of AHP, the weights of usability components were elicited from these experts. Compared to traditional usability evaluation methods, the major strength of the fuzzy method is that it captures the fuzziness and uncertainties in human judgments and provides an integrated framework that combines the vague judgments from multiple stages of a product evaluation process.

  3. Optical fiber-based full Mueller polarimeter for endoscopic imaging using a two-wavelength simultaneous measurement method.

    Science.gov (United States)

    Vizet, Jérémy; Manhas, Sandeep; Tran, Jacqueline; Validire, Pierre; Benali, Abdelali; Garcia-Caurel, Enric; Pierangelo, Angelo; De Martino, Antonello; Pagnoux, Dominique

    2016-07-01

    This paper reports a technique based on spectrally differential measurement for determining the full Mueller matrix of a biological sample through an optical fiber. In this technique, two close wavelengths were used simultaneously, one for characterizing the fiber and the other for characterizing the assembly of fiber and sample. The characteristics of the fiber measured at one wavelength were used to decouple its contribution from the measurement on the assembly of fiber and sample and then to extract sample Mueller matrix at the second wavelength. The proof of concept was experimentally validated by measuring polarimetric parameters of various calibrated optical components through the optical fiber. Then, polarimetric images of histological cuts of human colon tissues were measured, and retardance, diattenuation, and orientation of the main axes of fibrillar regions were displayed. Finally, these images were successfully compared with images obtained by a free space Mueller microscope. As the reported method does not use any moving component, it offers attractive integration possibilities with an endoscopic probe.

  4. A Full-wave Model for Wave Propagation and Dissipation in the Inner Magnetosphere Using the Finite Element Method

    International Nuclear Information System (INIS)

    Valeo, Ernest; Johnson, Jay R.; Kim, Eun-Hwa; Phillips, Cynthia

    2012-01-01

    A wide variety of plasma waves play an important role in the energization and loss of particles in the inner magnetosphere. Our ability to understand and model wave-particle interactions in this region requires improved knowledge of the spatial distribution and properties of these waves as well as improved understanding of how the waves depend on changes in solar wind forcing and/or geomagnetic activity. To this end, we have developed a two-dimensional, finite element code that solves the full wave equations in global magnetospheric geometry. The code describes three-dimensional wave structure including mode conversion when ULF, EMIC, and whistler waves are launched in a two-dimensional axisymmetric background plasma with general magnetic field topology. We illustrate the capabilities of the code by examining the role of plasmaspheric plumes on magnetosonic wave propagation; mode conversion at the ion-ion and Alfven resonances resulting from external, solar wind compressions; and wave structure and mode conversion of electromagnetic ion cyclotron waves launched in the equatorial magnetosphere, which propagate along the magnetic field lines toward the ionosphere. We also discuss advantages of the finite element method for resolving resonant structures, and how the model may be adapted to include nonlocal kinetic effects.

  5. Proposed waste form performance criteria and testing methods for low-level mixed waste

    International Nuclear Information System (INIS)

    Franz, E.M.; Fuhrmann, M.; Bowerman, B.; Bates, S.; Peters, R.

    1994-08-01

    This document describes proposed waste form performance criteria and testing method that could be used as guidance in judging viability of a waste form as a physico-chemical barrier to releases of radionuclides and RCRA regulated hazardous components. It is assumed that release of contaminants by leaching is the single most important property by which the effectiveness of a waste form is judged. A two-tier regimen is proposed. The first tier includes a leach test required by the Environmental Protection Agency and a leach test designed to determine the net forward leach rate for a variety of materials. The second tier of tests are to determine if a set of stresses (i.e., radiation, freeze-thaw, wet-dry cycling) on the waste form adversely impact its ability to retain contaminants and remain physically intact. It is recommended that the first tier tests be performed first to determine acceptability. Only on passing the given specifications for the leach tests should other tests be performed. In the absence of site-specific performance assessments (PA), two generic modeling exercises are described which were used to calculate proposed acceptable leach rates

  6. Gene set analysis: limitations in popular existing methods and proposed improvements.

    Science.gov (United States)

    Mishra, Pashupati; Törönen, Petri; Leino, Yrjö; Holm, Liisa

    2014-10-01

    Gene set analysis is the analysis of a set of genes that collectively contribute to a biological process. Most popular gene set analysis methods are based on empirical P-value that requires large number of permutations. Despite numerous gene set analysis methods developed in the past decade, the most popular methods still suffer from serious limitations. We present a gene set analysis method (mGSZ) based on Gene Set Z-scoring function (GSZ) and asymptotic P-values. Asymptotic P-value calculation requires fewer permutations, and thus speeds up the gene set analysis process. We compare the GSZ-scoring function with seven popular gene set scoring functions and show that GSZ stands out as the best scoring function. In addition, we show improved performance of the GSA method when the max-mean statistics is replaced by the GSZ scoring function. We demonstrate the importance of both gene and sample permutations by showing the consequences in the absence of one or the other. A comparison of asymptotic and empirical methods of P-value estimation demonstrates a clear advantage of asymptotic P-value over empirical P-value. We show that mGSZ outperforms the state-of-the-art methods based on two different evaluations. We compared mGSZ results with permutation and rotation tests and show that rotation does not improve our asymptotic P-values. We also propose well-known asymptotic distribution models for three of the compared methods. mGSZ is available as R package from cran.r-project.org. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

  7. Proposal of Screening Method of Sleep Disordered Breathing Using Fiber Grating Vision Sensor

    Science.gov (United States)

    Aoki, Hirooki; Nakamura, Hidetoshi; Nakajima, Masato

    Every conventional respiration monitoring technique requires at least one sensor to be attached to the body of the subject during measurement, thereby imposing a sense of restraint that results in aversion against measurements that would last over consecutive days. To solve this problem, we developed a respiration monitoring system for sleepers, and it uses a fiber-grating vision sensor, which is a type of active image sensor to achieve non-contact respiration monitoring. In this paper, we verified the effectiveness of the system, and proposed screening method of the sleep disordered breathing. It was shown that our system could equivalently measure the respiration with thermistor and accelerograph. And, the respiratory condition of sleepers can be grasped by our screening method in one look, and it seems to be useful for the support of the screening of sleep disordered breathing.

  8. The Proposal to “Snapshot” Raim Method for Gnss Vessel Receivers Working in Poor Space Segment Geometry

    Directory of Open Access Journals (Sweden)

    Nowak Aleksander

    2015-12-01

    Full Text Available Nowadays, we can observe an increase in research on the use of small unmanned autonomous vessel (SUAV to patrol and guiding critical areas including harbours. The proposal to “snapshot” RAIM (Receiver Autonomous Integrity Monitoring method for GNSS receivers mounted on SUAV operating in poor space segment geometry is presented in the paper. Existing “snapshot” RAIM methods and algorithms which are used in practical applications have been developed for airborne receivers, thus two main assumptions have been made. The first one is that the geometry of visible satellites is strong. It means that the exclusion of any satellite from the positioning solution don’t cause significant deterioration of Dilution of Precision (DOP coefficients. The second one is that only one outlier could appear in pseudorange measurements. In case of SUAV operating in harbour these two assumptions cannot be accepted. Because of their small dimensions, GNSS antenna is only a few decimetres above sea level and regular ships, buildings and harbour facilities block and reflect satellite signals. Thus, different approach to “snapshot” RAIM is necessary. The proposal to method based on analyses of allowable maximal separation of positioning sub-solutions with using some information from EGNOS messages is described in the paper. Theoretical assumptions and results of numerical experiments are presented.

  9. Proposal and Implementation of a Robust Sensing Method for DVB-T Signal

    Science.gov (United States)

    Song, Chunyi; Rahman, Mohammad Azizur; Harada, Hiroshi

    This paper proposes a sensing method for TV signals of DVB-T standard to realize effective TV White Space (TVWS) Communication. In the TVWS technology trial organized by the Infocomm Development Authority (iDA) of Singapore, with regard to the sensing level and sensing time, detecting DVB-T signal at the level of -120dBm over an 8MHz channel with a sensing time below 1 second is required. To fulfill such a strict sensing requirement, we propose a smart sensing method which combines feature detection and energy detection (CFED), and is also characterized by using dynamic threshold selection (DTS) based on a threshold table to improve sensing robustness to noise uncertainty. The DTS based CFED (DTS-CFED) is evaluated by computer simulations and is also implemented into a hardware sensing prototype. The results show that the DTS-CFED achieves a detection probability above 0.9 for a target false alarm probability of 0.1 for DVB-T signals at the level of -120dBm over an 8MHz channel with the sensing time equals to 0.1 second.

  10. A Proposal of New Spherical Particle Modeling Method Based on Stochastic Sampling of Particle Locations in Monte Carlo Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Song Hyun; Kim, Do Hyun; Kim, Jong Kyung [Hanyang Univ., Seoul (Korea, Republic of); Noh, Jea Man [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-10-15

    To the high computational efficiency and user convenience, the implicit method had received attention; however, it is noted that the implicit method in the previous studies has low accuracy at high packing fraction. In this study, a new implicit method, which can be used at any packing fraction with high accuracy, is proposed. In this study, the implicit modeling method in the spherical particle distributed medium for using the MC simulation is proposed. A new concept in the spherical particle sampling was developed to solve the problems in the previous implicit methods. The sampling method was verified by simulating the sampling method in the infinite and finite medium. The results show that the particle implicit modeling with the proposed method was accurately performed in all packing fraction boundaries. It is expected that the proposed method can be efficiently utilized for the spherical particle distributed mediums, which are the fusion reactor blanket, VHTR reactors, and shielding analysis.

  11. Disintegration of sublingual tablets: proposal for a validated test method and acceptance criterion.

    Science.gov (United States)

    Weda, M; van Riet-Nales, D A; van Aalst, P; de Kaste, D; Lekkerkerker, J F F

    2006-12-01

    In the Netherlands the market share of isosorbide dinitrate 5 mg sublingual tablets is dominated by 2 products (A and B). In the last few years complaints have been received from health care professionals on product B. During patient use the disintegration of the tablet was reported to be slow and/or incomplete, and ineffectiveness was experienced. In the European Pharmacopoeia (Ph. Eur.) no requirement is present for the disintegration time of sublingual tablets. The purpose of this study was to compare the in vitro disintegration time of products A and B, and to establish a suitable test method and acceptance criterion. A and B were tested with the Ph. Eur. method described in the monograph on disintegration of tablets and capsules as well as with 3 modified tests using the same Ph. Eur. apparatus, but without movement of the basket-rack assembly. In modified test 1 and modified test 2 water was used as medium (900 ml and 50 ml respectively), whereas in modified test 3 artificial saliva was used (50 ml). In addition, disintegration was tested in Nessler tubes with 0.5 and 2 ml of water. Finally, the Ph. Eur. method was also applied to other sublingual tablets with other drug substances on the Dutch market. With modified test 3 no disintegration could be achieved within 20 min. With the Ph. Eur. method and modified tests 1 and 2 product A and B differed significantly (p disintegration times. These 3 methods were capable of discriminating between products and between batches. The time measured with the Ph. Eur. method was significantly lower compared to modified tests 1 and 2 (p tablets the disintegration time should be tested. The Ph. Eur. method is considered suitable for this test. In view of the products currently on the market and taking into consideration requirements in the United States Pharmacopeia and Japanese Pharmacopoeia, an acceptance criterion of not more than 2 min is proposed.

  12. Proposed method to calculate FRMAC intervention levels for the assessment of radiologically contaminated food and comparison of the proposed method to the U.S. FDA's method to calculate derived intervention levels

    Energy Technology Data Exchange (ETDEWEB)

    Kraus, Terrence D.; Hunt, Brian D.

    2014-02-01

    This report reviews the method recommended by the U.S. Food and Drug Administration for calculating Derived Intervention Levels (DILs) and identifies potential improvements to the DIL calculation method to support more accurate ingestion pathway analyses and protective action decisions. Further, this report proposes an alternate method for use by the Federal Emergency Radiological Assessment Center (FRMAC) to calculate FRMAC Intervention Levels (FILs). The default approach of the FRMAC during an emergency response is to use the FDA recommended methods. However, FRMAC recommends implementing the FIL method because we believe it to be more technically accurate. FRMAC will only implement the FIL method when approved by the FDA representative on the Federal Advisory Team for Environment, Food, and Health.

  13. Morphology effects on the bandgap of silicon nanocrystals—Numerically modelled by a full multi-grid method

    Science.gov (United States)

    Puthen Veettil, Binesh; König, Dirk; Huang, Shujuan; Patterson, Robert; Conibeer, Gavin

    2017-02-01

    Silicon nanocrystals embedded in a dielectric matrix have been considered a potential candidate for many optoelectronic and photovoltaic applications and have been under vigorous study in recent years. One of the main properties of interest in this application is the absorption bandgap, which is determined by the quantum confinement of silicon nanocrystals. The ability to predict the absorption bandgap is a key step in designing an optimum solar cell using this material. Although several higher level algorithms are available to predict the electronic confinement in these nanocrystals, most of them make regular-shape assumptions for the ease of computation. In this work, we present a model for the accurate prediction of the quantum confinement in silicon nanocrystals of non-regular shape by employing an efficient, self-consistent Full-Multi-Grid method. Confined energies in spherical, elongated, and arbitrarily shaped nanocrystals are calculated. The excited level calculations quantify the wavefunction coupling and energy level splitting arising due to the proximity of dots. The splitting magnitude was found to be as high as 0.1 eV for the 2 nm size silicon quantum dots. The decrease in confinement energy due to the elongation of dots was found to be more than 0.2 eV, and the trend was similar for different dielectric materials. Theoretical predictions were compared to the results from optical and structural characterisation and found to be in agreement. The loss of degeneracy in highly asymmetric quantum dots, such as a "horse-shoe" shaped quantum dot, significantly affects the excited state energies.

  14. A full scale comparative study of methods for generation of functional Dendritic cells for use as cancer vaccines

    Directory of Open Access Journals (Sweden)

    Kvalheim Gunnar

    2007-07-01

    Full Text Available Background Dendritic cells (DCs are professional antigen-presenting cells with the ability to induce primary T-cell responses and are commonly produced by culturing monocytes in the presence of IL-4 and GM-CSF for 5–7 days (Standard DC. Recently, Dauer and co-workers presented a modified protocol for differentiation of human monocytes into mature DCs within 48 hours (Fast DC. Here we report a functional comparison of the two strategies for generation of DCs from human monocytes with adaptions for large-scale clinical use. Methods The Elutra Cell Selection System was used to isolate monocytes after collection of leukapheresis product. The enriched monocytes were cultured in gas permeable Teflon bags with IL-4 and GM-CSF for 24 hours (Fast DC or 5 days (Standard DC to obtain immature DCs. The cells were then transfected with mRNA from the leukemia cell line Jurkat E6 by electroporation and incubated for additional 24 h or 2 days in the presence of pro-inflammatory cytokines (TNFα, IL-1β, IL-6 and PGE2 to obtain mature DCs. Results Mature Fast DC and Standard DC displayed comparable levels of many markers expressed on DC, including HLA-DR, CD83, CD86, CD208 and CCR7. However, compared to Standard DC, mature Fast DC was CD14high CD209low. Fast DC and Standard DC transfected with Jurkat E6-cell mRNA were equally able to elicit T cell specifically recognizing transfected DCs in vitro. IFNγ-secreting T cells were observed in both the CD4+ and CD8+ subsets. Conclusion Our results indicate that mature Fast DC are functional antigen presenting cells (APCs capable of inducing primary T-cell responses, and suggest that these cells may be valuable for generation of anti-tumor vaccines.

  15. Improve the functional status of students using the proposed method recovery

    Directory of Open Access Journals (Sweden)

    Evtukh M.I.

    2012-12-01

    Full Text Available Purpose - to improve the organizational and methodological foundations of physical education for the improvement of high school students in training. The study involved 152 students of the second year of the International Economics and Humanities University named after Stepan Demyanchuk. Students were divided into control (n = 76 and primary (n = 76 groups, which were similar in age and physical development. At the end of the study, through the application of the proposed technique improvement in students the core group, was able to restore the function of the respiratory and cardiovascular systems to the possibilities of healthy untrained people. A similar increase in the functionality of the core group of students registered with the definition of the index Skibinski - held a combined evaluation of functions of the respiratory and cardiovascular systems of students and determine its growth with satisfactory to good level.

  16. Proposal of adaptive human interface and study of interface evaluation method for plant operators

    International Nuclear Information System (INIS)

    Ujita, Hiroshi; Kubota, Ryuji.

    1994-01-01

    In this report, a new concept of human interface adaptive to plant operators' mental model, cognitive process and psychological state which change with time is proposed. It is composed of a function to determine information which should be indicated to operators based on the plant situation, a function to estimate operators' internal conditions, and a function to arrange the information amount, position, timing, form etc. based on their conditions. The method to evaluate the fitness of the interface by using the analysis results based on cognitive science, ergonomics, psychology and physiology is developed to achieve such an interface. Fundamental physiological experiments have been performed. Stress and workload can be identified by the ratio of the power average of the α wave fraction of a brain wave and be distinguished by the ratio of the standard deviation of the R-R interval in test and at rest, in the case of low stress such as mouse operation, calculation and walking. (author)

  17. Proposal of adaptive human interface and study of interface evaluation method for plant operators

    Energy Technology Data Exchange (ETDEWEB)

    Ujita, Hiroshi [Hitachi Ltd., Ibaraki (Japan). Energy Research Lab.; Kubota, Ryuji

    1994-07-01

    In this report, a new concept of human interface adaptive to plant operators' mental model, cognitive process and psychological state which change with time is proposed. It is composed of a function to determine information which should be indicated to operators based on the plant situation, a function to estimate operators' internal conditions, and a function to arrange the information amount, position, timing, form etc. based on their conditions. The method to evaluate the fitness of the interface by using the analysis results based on cognitive science, ergonomics, psychology and physiology is developed to achieve such an interface. Fundamental physiological experiments have been performed. Stress and workload can be identified by the ratio of the power average of the [alpha] wave fraction of a brain wave and be distinguished by the ratio of the standard deviation of the R-R interval in test and at rest, in the case of low stress such as mouse operation, calculation and walking. (author).

  18. Proposal of a method for formulating strategy in small and medium enterprises

    Directory of Open Access Journals (Sweden)

    Luís Henrique Piovezan

    2008-07-01

    Full Text Available Strategy models found in the literature are usually more suitable for big companies. However, small and medium enterprises (SME also need to plan their strategies, but in such a way that considers their peculiarities. In this context, this paper presents a simple method for strategy formulation and deployment in SME. This method was developed through a sequence of cases studies, developed in small companies (10 to 500 employees. The final version of this method is a seven-step framework that considers both business environment and firm core competencies. The final aim is the alignment of business and manufacturing strategies. This framework can be considered suitable for SME, since it is simple and allows saving time and scarce available resources for strategy formulation, both important issues in this kind of enterprises. Finally, a case study is presented, encompassing the analysis of the application of the final version of the method in a small Brazilian company. Key-words: Competitive Strategy, Small Business Strategy, Manufacturing Strategy.

  19. Proposed Model for Integrating RAMS Method in the Design Process in Construction

    Directory of Open Access Journals (Sweden)

    Saad Al-Jibouri

    2010-05-01

    Full Text Available There is a growing trend in the Netherlands for outsourcing public construction activities to the private sector through the use of integrated contracts. There is also an increasing emphasis from public clients on the use of RAMS and life cycle costing (LCC in the design process of infrastructural projects to improve the performance of designed systems and optimize the project cost. RAMS is an acronym for `reliability, availability, maintainability and safety' and represents a collection of techniques to provide predictions of the performance targets of the required system. Increasingly, RAMS targets are being specified in invitation to tender or contract documents and the parties responsible for the design are required to provide evidence of its application in their design. Recent evidence from practice, complemented with a literature study, has shown that the knowledge and application of RAMS in infrastructural designs are in their infancy compared with other industrial sectors and many designers in construction do not have the necessary knowledge and experience to apply it. This paper describes a proposed model for the integration of RAMS and LCC into the design process in construction. A variation of the model for the application of RAMS in `design, build, finance and maintain' (DBFM contracts that include maintenance requirements is also proposed. The two models involve providing guidelines to simplify the application of RAMs by the designers. The model has been validated for its practicality and usefulness during a workshop by experienced designers. DOI: 10.3763/aedm.2008.0100 Published in the Journal AEDM - Volume 5, Number 4, 2009 , pp. 179-192(14

  20. A proposal on alternative sampling-based modeling method of spherical particles in stochastic media for Monte Carlo simulation

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Song Hyun; Lee, Jae Yong; KIm, Do Hyun; Kim, Jong Kyung [Dept. of Nuclear Engineering, Hanyang University, Seoul (Korea, Republic of); Noh, Jae Man [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-08-15

    Chord length sampling method in Monte Carlo simulations is a method used to model spherical particles with random sampling technique in a stochastic media. It has received attention due to the high calculation efficiency as well as user convenience; however, a technical issue regarding boundary effect has been noted. In this study, after analyzing the distribution characteristics of spherical particles using an explicit method, an alternative chord length sampling method is proposed. In addition, for modeling in finite media, a correction method of the boundary effect is proposed. Using the proposed method, sample probability distributions and relative errors were estimated and compared with those calculated by the explicit method. The results show that the reconstruction ability and modeling accuracy of the particle probability distribution with the proposed method were considerably high. Also, from the local packing fraction results, the proposed method can successfully solve the boundary effect problem. It is expected that the proposed method can contribute to the increasing of the modeling accuracy in stochastic media.

  1. A proposal on alternative sampling-based modeling method of spherical particles in stochastic media for Monte Carlo simulation

    International Nuclear Information System (INIS)

    Kim, Song Hyun; Lee, Jae Yong; KIm, Do Hyun; Kim, Jong Kyung; Noh, Jae Man

    2015-01-01

    Chord length sampling method in Monte Carlo simulations is a method used to model spherical particles with random sampling technique in a stochastic media. It has received attention due to the high calculation efficiency as well as user convenience; however, a technical issue regarding boundary effect has been noted. In this study, after analyzing the distribution characteristics of spherical particles using an explicit method, an alternative chord length sampling method is proposed. In addition, for modeling in finite media, a correction method of the boundary effect is proposed. Using the proposed method, sample probability distributions and relative errors were estimated and compared with those calculated by the explicit method. The results show that the reconstruction ability and modeling accuracy of the particle probability distribution with the proposed method were considerably high. Also, from the local packing fraction results, the proposed method can successfully solve the boundary effect problem. It is expected that the proposed method can contribute to the increasing of the modeling accuracy in stochastic media

  2. Proposed method to produce a highly polarized e+ beam for future linear colliders

    International Nuclear Information System (INIS)

    Okugi, Toshiyuki; Chiba, Masami; Kurihara, Yoshimasa

    1996-01-01

    We propose a method to produce a spin-polarized e + beam using e + e - pair-creation by circularly polarized photons. Assuming Compton scattering of an unpolarized e - beam and circularly polarized laser light, scattered γ-rays at the high end of the energy spectrum are also circularly polarized. If those γ-rays are utilized to create e ± pairs on a thin target, the spin-polarization is preserved for e + 's at the high end of their energy spectrum. By using the injector linac of Accelerator Test Facility at KEK and a commercially available Nd:YAG pulse laser, we can expect about 10 5 polarized e + 's per second with a degree of polarization of 80% and a kinetic energy of 35-80 MeV. The apparatus for creation and measurement of polarized e + 's is being constructed. We present new idea for possible application of our method to future linear colliders by utilizing a high-power CO 2 laser. (author)

  3. A calibration method for proposed XRF measurements of arsenic and selenium in nail clippings

    International Nuclear Information System (INIS)

    Gherase, Mihai R; Fleming, David E B

    2011-01-01

    A calibration method for proposed x-ray fluorescence (XRF) measurements of arsenic and selenium in nail clippings is demonstrated. Phantom nail clippings were produced from a whole nail phantom (0.7 mm thickness, 25 x 25 mm 2 area) and contained equal concentrations of arsenic and selenium ranging from 0 to 20 μg g -1 in increments of 5 μg g -1 . The phantom nail clippings were then grouped in samples of five different masses: 20, 40, 60, 80 and 100 mg for each concentration. Experimental x-ray spectra were acquired for each of the sample masses using a portable x-ray tube and a detector unit. Calibration lines (XRF signal in a number of counts versus stoichiometric elemental concentration) were produced for each of the two elements. A semi-empirical relationship between the mass of the nail phantoms (m) and the slope of the calibration line (s) was determined separately for arsenic and selenium. Using this calibration method, one can estimate elemental concentrations and their uncertainties from the XRF spectra of human nail clippings. (note)

  4. Proposed method for reconstructing velocity profiles using a multi-electrode electromagnetic flow meter

    International Nuclear Information System (INIS)

    Kollár, László E; Lucas, Gary P; Zhang, Zhichao

    2014-01-01

    An analytical method is developed for the reconstruction of velocity profiles using measured potential distributions obtained around the boundary of a multi-electrode electromagnetic flow meter (EMFM). The method is based on the discrete Fourier transform (DFT), and is implemented in Matlab. The method assumes the velocity profile in a section of a pipe as a superposition of polynomials up to sixth order. Each polynomial component is defined along a specific direction in the plane of the pipe section. For a potential distribution obtained in a uniform magnetic field, this direction is not unique for quadratic and higher-order components; thus, multiple possible solutions exist for the reconstructed velocity profile. A procedure for choosing the optimum velocity profile is proposed. It is applicable for single-phase or two-phase flows, and requires measurement of the potential distribution in a non-uniform magnetic field. The potential distribution in this non-uniform magnetic field is also calculated for the possible solutions using weight values. Then, the velocity profile with the calculated potential distribution which is closest to the measured one provides the optimum solution. The reliability of the method is first demonstrated by reconstructing an artificial velocity profile defined by polynomial functions. Next, velocity profiles in different two-phase flows, based on results from the literature, are used to define the input velocity fields. In all cases, COMSOL Multiphysics is used to model the physical specifications of the EMFM and to simulate the measurements; thus, COMSOL simulations produce the potential distributions on the internal circumference of the flow pipe. These potential distributions serve as inputs for the analytical method. The reconstructed velocity profiles show satisfactory agreement with the input velocity profiles. The method described in this paper is most suitable for stratified flows and is not applicable to axisymmetric flows in

  5. Proposal of Environmental Impact Assessment Method for Concrete in South Korea: An Application in LCA (Life Cycle Assessment

    Directory of Open Access Journals (Sweden)

    Tae Hyoung Kim

    2016-11-01

    Full Text Available This study aims to develop a system for assessing the impact of the substances discharged from concrete production process on six environmental impact categories, i.e., global warming (GWP, acidification (AP, eutrophication (EP, abiotic depletion (ADP, ozone depletion (ODP, and photochemical oxidant creation (POCP, using the life a cycle assessment (LCA method. To achieve this, this study proposed an LCA method specifically applicable to the Korean concrete industry by adapting the ISO standards to suit the Korean situations. The proposed LCA method involves a system that performs environmental impact assessment on the basis of input information on concrete mix design, transport distance, and energy consumption in a batch plant. The Concrete Lifecycle Assessment System (CLAS thus developed provides user-friendly support for environmental impact assessment with specialized database for concrete mix materials and energy sources. In the case analysis using the CLAS, among the substances discharged from the production of 24 MPa concrete, those contributing to GWP, AP, EP, ADP, ODP, and POCP were assessed to amount to 309 kg-CO2 eq/m3, 28.7 kg-SO2 eq/m3, 5.21 kg-PO43− eq/m3, 0.000049 kg-CFC11 eq/m3, 34 kg/m3, and 21 kg-Ethylene eq/m3, respectively. Of these six environmental impact categories selected for the LCA in this study, ordinary Portland cement (OPC was found to contribute most intensely to GWP and POCP, and aggregates, to AP, EP, ODP, and ADP. It was also found that the mix design with increased prop proportion of recycled aggregate was found to contribute to reducing the impact in all other categories.

  6. A proposed through-flow inverse method for the design of mixed-flow pumps

    Science.gov (United States)

    Borges, Joao Eduardo

    1991-01-01

    A through-flow (hub-to-shroud) truly inverse method is proposed and described. It uses an imposition of mean swirl, i.e., radius times mean tangential velocity, given throughout the meridional section of the turbomachine as an initial design specification. In the present implementation, it is assumed that the fluid is inviscid, incompressible, and irrotational at inlet and that the blades are supposed to have zero thickness. Only blade rows that impart to the fluid a constant work along the space are considered. An application of this procedure to design the rotor of a mixed-flow pump is described in detail. The strategy used to find a suitable mean swirl distribution and the other design inputs is also described. The final blade shape and pressure distributions on the blade surface are presented, showing that it is possible to obtain feasible designs using this technique. Another advantage of this technique is the fact that it does not require large amounts of CPU time.

  7. Restoring stream habitat connectivity: a proposed method for prioritizing the removal of resident fish passage barriers.

    Science.gov (United States)

    O'Hanley, Jesse R; Wright, Jed; Diebel, Matthew; Fedora, Mark A; Soucy, Charles L

    2013-08-15

    Systematic methods for prioritizing the repair and removal of fish passage barriers, while growing of late, have hitherto focused almost exclusively on meeting the needs of migratory fish species (e.g., anadromous salmonids). An important but as of yet unaddressed issue is the development of new modeling approaches which are applicable to resident fish species habitat restoration programs. In this paper, we develop a budget constrained optimization model for deciding which barriers to repair or remove in order to maximize habitat availability for stream resident fish. Habitat availability at the local stream reach is determined based on the recently proposed C metric, which accounts for the amount, quality, distance and level of connectivity to different stream habitat types. We assess the computational performance of our model using geospatial barrier and stream data collected from the Pine-Popple Watershed, located in northeast Wisconsin (USA). The optimization model is found to be an efficient and practical decision support tool. Optimal solutions, which are useful in informing basin-wide restoration planning efforts, can be generated on average in only a few minutes. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. How to identify partial exposures to ionizing radiation? Proposal for a cytogenetic method

    International Nuclear Information System (INIS)

    Fernandes, T.S.; Silva, E.B.; Pinto, M.M.P.L.; Amaral, A.; Lloyd, David

    2013-01-01

    In cases of radiological incidents or in occupational exposures to ionizing radiation, the majority of exposures are not related to the total body, but only partial. In this context, if the cytogenetic dosimetry is performed, there will be an underestimation of the absorbed dose due to the dilution of irradiated cells with non-irradiated cells. Considering the norms of NR 32 - Safety and Health in the Work of Health Service - which recommends cytogenetic dosimetry in the investigation of accidental exposures to ionizing radiations, it is necessary to develop of a tool to provide a better identification of partial exposures. With this aim, a partial body exposure was simulated by mixing, in vitro, 70% of blood irradiated with 4 Gy of X-rays with 30% of unirradiated blood from the same healthy donor. Aliquots of this mixture were cultured for 48 and 72 hours. Prolonging the time of cell culture from 48 to 72 hours produced no significant change in the yield of dicentrics. However, when only M1 (first division cells) were analyzed, the frequency of dicentrics per cell was increased. Prolonging the time of cell culture allowed cells in mitotic delay by irradiation to reach metaphase, and thus provides enough time for the damage to be visualized. The results of this research present the proposed method as an important tool in the investigation of exposed individuals, allowing associating the cytogenetic analysis with the real percentage of irradiated cells, contributing significantly for the decision making in terms of occupational health. (author)

  9. A Proposal of Client Application Architecture using Loosely Coupled Component Connection Method in Banking Branch System

    Science.gov (United States)

    Someya, Harushi; Mori, Yuichi; Abe, Masahiro; Machida, Isamu; Hasegawa, Atsushi; Yoshie, Osamu

    Due to the deregulation of financial industry, the branches in banking industry need to shift to the sales-oriented bases from the operation-oriented bases. For corresponding to this movement, new banking branch systems are being developed. It is the main characteristics of new systems that we bring the form operations that have traditionally been performed at each branch into the centralized operation center for the purpose of rationalization and efficiency of the form operations. The branches treat a wide variety of forms. The forms can be described by common items in many cases, but the items include the different business logic and each form has the different relation among the items. And there is a need to develop the client application by user oneself. Consequently the challenge is to arrange the development environment that is high reusable, easy customizable and user developable. We propose a client application architecture that has a loosely coupled component connection method, and allows developing the applications by only describing the screen configurations and their transitions in XML documents. By adopting our architecture, we developed client applications of the centralized operation center for the latest banking branch system. Our experiments demonstrate good performances.

  10. Proposed algorithm to improve job shop production scheduling using ant colony optimization method

    Science.gov (United States)

    Pakpahan, Eka KA; Kristina, Sonna; Setiawan, Ari

    2017-12-01

    This paper deals with the determination of job shop production schedule on an automatic environment. On this particular environment, machines and material handling system are integrated and controlled by a computer center where schedule were created and then used to dictate the movement of parts and the operations at each machine. This setting is usually designed to have an unmanned production process for a specified interval time. We consider here parts with various operations requirement. Each operation requires specific cutting tools. These parts are to be scheduled on machines each having identical capability, meaning that each machine is equipped with a similar set of cutting tools therefore is capable of processing any operation. The availability of a particular machine to process a particular operation is determined by the remaining life time of its cutting tools. We proposed an algorithm based on the ant colony optimization method and embedded them on matlab software to generate production schedule which minimize the total processing time of the parts (makespan). We test the algorithm on data provided by real industry and the process shows a very short computation time. This contributes a lot to the flexibility and timelines targeted on an automatic environment.

  11. Method to determine full work of fracture from disk shaped compact tension tests on hot-mix asphalt

    CSIR Research Space (South Africa)

    Denneman, E

    2010-08-01

    Full Text Available crack through the entire ligament area will not be recorded. The missing part of the exponential tail of the load-CMOD curve can be modelled using the methodology provided in this paper. The results indicate that 12.6 per cent of the fracture energy... for Earthquake Engineering Simulation v1.7.5. Berkeley: Pacific Earthquake Engineering Research Center, University of California. Rocco, C., Guinea, G., Planas, J., Elices, M., 1999a. Size effect and boundary conditions in the Brazilian test: Experimental...

  12. Identification of wastewater treatment processes for nutrient removal on a full-scale WWTP by statistical methods

    DEFF Research Database (Denmark)

    Carstensen, Jakob; Madsen, Henrik; Poulsen, Niels Kjølstad

    1994-01-01

    of the processes, i.e. including prior knowledge, with the significant effects found in data by using statistical identification methods. Rates of the biochemical and hydraulic processes are identified by statistical methods and the related constants for the biochemical processes are estimated assuming Monod...... kinetics. The models only include those hydraulic and kinetic parameters, which have shown to be significant in a statistical sense, and hence they can be quantified. The application potential of these models is on-line control, because the present state of the plant is given by the variables of the models......The introduction of on-line sensors of nutrient salt concentrations on wastewater treatment plants opens a wide new area of modelling wastewater processes. Time series models of these processes are very useful for gaining insight in real time operation of wastewater treatment systems which deal...

  13. Evaluating the Infiltration Performance of Eight Dutch Permeable Pavements Using a New Full-Scale Infiltration Testing Method

    Directory of Open Access Journals (Sweden)

    Floris Boogaard

    2014-07-01

    Full Text Available Permeable pavements are a type of sustainable urban drainage system (SUDS technique that are used around the world to infiltrate and treat urban stormwater runoff and to minimize runoff volumes. Urban stormwater runoff contains significant concentrations of suspended sediments that can cause clogging and reduce the infiltration capacity and effectiveness of permeable pavements. It is important for stormwater managers to be able to determine when the level of clogging has reached an unacceptable level, so that they can schedule maintenance or replacement activities as required. Newly-installed permeable pavements in the Netherlands must demonstrate a minimum infiltration capacity of 194 mm/h (540 l/s/ha. Other commonly used permeable pavement guidelines in the Netherlands recommend that maintenance is undertaken on permeable pavements when the infiltration falls below 0.50 m/d (20.8 mm/h. This study used a newly-developed, full-scale infiltration test procedure to evaluate the infiltration performance of eight permeable pavements in five municipalities that had been in service for over seven years in the Netherlands. The determined infiltration capacities vary between 29 and 342 mm/h. Two of the eight pavements show an infiltration capacity higher than 194 mm/h, and all infiltration capacities are higher than 20.8 mm/h. According to the guidelines, this suggests that none of the pavements tested in this study would require immediate maintenance.

  14. Alpins and thibos vectorial astigmatism analyses: proposal of a linear regression model between methods

    Directory of Open Access Journals (Sweden)

    Giuliano de Oliveira Freitas

    2013-10-01

    Full Text Available PURPOSE: To determine linear regression models between Alpins descriptive indices and Thibos astigmatic power vectors (APV, assessing the validity and strength of such correlations. METHODS: This case series prospectively assessed 62 eyes of 31 consecutive cataract patients with preoperative corneal astigmatism between 0.75 and 2.50 diopters in both eyes. Patients were randomly assorted among two phacoemulsification groups: one assigned to receive AcrySof®Toric intraocular lens (IOL in both eyes and another assigned to have AcrySof Natural IOL associated with limbal relaxing incisions, also in both eyes. All patients were reevaluated postoperatively at 6 months, when refractive astigmatism analysis was performed using both Alpins and Thibos methods. The ratio between Thibos postoperative APV and preoperative APV (APVratio and its linear regression to Alpins percentage of success of astigmatic surgery, percentage of astigmatism corrected and percentage of astigmatism reduction at the intended axis were assessed. RESULTS: Significant negative correlation between the ratio of post- and preoperative Thibos APVratio and Alpins percentage of success (%Success was found (Spearman's ρ=-0.93; linear regression is given by the following equation: %Success = (-APVratio + 1.00x100. CONCLUSION: The linear regression we found between APVratio and %Success permits a validated mathematical inference concerning the overall success of astigmatic surgery.

  15. Prediction of the heat gain of external walls: An innovative approach for full-featured excitations based on the simplified method of Mackey-and-Wright

    International Nuclear Information System (INIS)

    Ruivo, C.R.; Vaz, D.C.

    2015-01-01

    Highlights: • The transient thermal behaviour of external multilayer walls of buildings is studied. • Reference results for four representative walls, obtained with a numerical model, are provided. • Shortcomings of approaches based on the Mackey-and-Wright method are identified. • Handling full-feature excitations with Fourier series decomposition improves accuracy. • A simpler, yet accurate, promising novel approach to predict heat gain is proposed. - Abstract: Nowadays, simulation tools are available for calculating the thermal loads of multiple rooms of buildings, for given inputs. However, due to inaccuracies or uncertainties in some of the input data (e.g., thermal properties, air infiltrations flow rates, building occupancy), the evaluated thermal load may represent no more than just an estimate of the actual thermal load of the spaces. Accordingly, in certain practical situations, simplified methods may offer a more reasonable trade-off between effort and results accuracy than advanced software. Hence, despite the advances in computing power over the last decades, simplified methods for the evaluation of thermal loads are still of great interest nowadays, for both the practicing engineer and the graduating student, since these can be readily implemented or developed in common computational-tools, like a spreadsheet. The method of Mackey and Wright (M&W) is a simplified method that upon values of the decrement factor and time lag of a wall (or roof) estimates the instantaneous rate of heat transfer through its indoor surface. It assumes cyclic behaviour and shows good accuracy when the excitation and response have matching shapes, but it involves non negligible error otherwise, for example, in the case of walls of high thermal inertia. The aim of this study is to develop a simplified procedure that considerably improves the accuracy of the M&W method, particularly for excitations that noticeably depart from the sinusoidal shape, while not

  16. A Potential Method for Body and Surface Wave Propagation in Transversely Isotropic Half- and Full-Spaces

    Directory of Open Access Journals (Sweden)

    Mehdi Raoofian Naeeni

    2016-12-01

    Full Text Available The problem of propagation of plane wave including body and surface waves propagating in a transversely isotropic half-space with a depth-wise axis of material symmetry is investigated in details. Using the advantage of representation of displacement fields in terms of two complete scalar potential functions, the coupled equations of motion are uncoupled and reduced to two independent equations for potential functions. In this paper, the secular equations for determination of body and surface wave velocities are derived in terms of both elasticity coefficients and the direction of propagation. In particular, the longitudinal, transverse and Rayleigh wave velocities are determined in explicit forms. It is also shown that in transversely isotropic materials, a Rayleigh wave may propagate in different manner from that of isotropic materials. Some numerical results for synthetic transversely isotropic materials are also illustrated to show the behavior of wave motion due to anisotropic nature of the problem.

  17. Full text

    African Journals Online (AJOL)

    IndexCopernicus Portal System

    1Department of Surgery, Obafemi Awolowo, 2Department of Community Health,. Obafemi ... the use of mesh, either open or laparoscopic [15,21], but this ... recurrence. METHODS AND PATIENTS .... TAH-BSO* = Total abdominal hysterectomy and bilateral salpingoophorectomy. Recurrent I.H. # = Recurrent inguinal hernia.

  18. Full nonlinear treatment of the global thermospheric wind system. Part 1: Mathematical method and analysis of forces

    Science.gov (United States)

    Blum, P. W.; Harris, I.

    1973-01-01

    The equations of horizontal motion of the neutral atmosphere between 120 and 500 km are integrated with the inclusion of all the nonlinear terms of the convective derivative and the viscous forces due to vertical and horizontal velocity gradients. Empirical models of the distribution of neutral and charged particles are assumed to be known. The model of velocities developed is a steady state model. In part 1 the mathematical method used in the integration of the Navier-Stokes equations is described and the various forces are analysed.

  19. THE PROPOSED METHODOLOGIES FOR THE SIX SIGMA METHOD AND TQM STRATEGY AS WELL AS THEIR APPLICATION IN PRACTICE IN MACEDONIA

    Directory of Open Access Journals (Sweden)

    Elizabeta Mitreva

    2014-05-01

    Full Text Available This paper presents the proposed methodologies for the Six Sigma method and the TQM strategy as well as their application in practice in Macedonia. Although the philosophy of the total quality management (TQM is deeply involved in many industries and business areas of European and other countries it is insufficiently known and present in our country and other developing countries. The same applies to the Six Sigma approach of reducing the dispersion of a process and it is present in a small fraction in Macedonian companies. The results of the implementation have shown that the application of the Six Sigma approach does not refer to the number of defects per million opportunities but to the systematic and systemic lowering of the dispersion process. The operation and effect of the implementation of the six sigma method engages experts that receive a salary depending on the success of the Six Sigma program. On other hand the results of the application of the TQM methodology within the Macedonian companies will depend on the commitment of all employees and their motivation.

  20. A proposed method for accurate 3D analysis of cochlear implant migration using fusion of cone beam CT

    Directory of Open Access Journals (Sweden)

    Guido eDees

    2016-01-01

    Full Text Available IntroductionThe goal of this investigation was to compare fusion of sequential cone beam CT volumes to the gold standard (fiducial registration in order to be able to analyze clinical CI migration with high accuracy in three dimensions. Materials and MethodsPaired time-lapsed cone beam CT volumes were performed on five human cadaver temporal bones and one human subject. These volumes were fused using 3D Slicer 4 and BRAINSFit software. Using a gold standard fiducial technique, the accuracy, robustness and performance time of the fusion process were assessed.Results This proposed fusion protocol achieves a sub voxel mean Euclidean distance of 0.05 millimeter in human cadaver temporal bones and 0.16 millimeter when applied to the described in vivo human synthetic data set in over 95% of all fusions. Performance times are less than two minutes.ConclusionHere a new and validated method based on existing techniques is described which could be used to accurately quantify migration of cochlear implant electrodes.

  1. A "conservative" method of thoracic wall dissection: a proposal for teaching human anatomy.

    Science.gov (United States)

    Barberini, Fabrizio; Brunone, Francesca

    2008-01-01

    The common methods of dissection exposing the thoracic organs include crossing of the wall together with wide resection of its muscular planes. In order to preserve these structures, a little demolishing technique of the thoracic wall is proposed, entering the thoracic cavity without extensive resection of the pectoral muscles. This method is based on the fact that these muscles rise up from the wall, like a bridge connecting the costal plane with the upper limb, and that the pectoralis major shows a segmental constitution. SUPERIOR LIMIT: Resect the sternal manubrium transversely between the 1st and the 2nd rib. The incision is prolonged along the 1st intercostal space, separating the first sterno-costal segment of the pectoralis major from the second one, and involving the intercostal muscles as far as the medial margin of the pectoralis minor. This muscle must be raised up, and the transverse resection continued below its medial margin latero-medially along the 1st intercostal space, to rejoin the cut performed before. Then, the incision of the 1st intercostal space is prolonged below the lateral margin of the pectoralis minor, which must be kept raised up, medio-laterally as far as the anterior axillary line. INFERIOR LIMIT: It corresponds to the inferior border of the thoracic cage, resected from the xiphoid process to the anterior axillary line, together with the sterno-costal insertions of the diaphragm. Then, an incision of the sterno-pericardial ligaments and a median sternotomy from the xiphoid process to the transverse resection of the manubrium should be performed. LATERAL LIMIT: From the point of crossing of the anterior axillary line with the inferior limit, resect the ribs from the 10th to the 2nd one. The lateral part of the pectoralis major must be raised up, so that the costal resection may be continued below it. Then, at the lateral extremity of the superior incision, the first and the second sternocostal segment of the pectoralis major must be

  2. A proposed new method for the determination of the solar irradiance at EUV wavelength range

    Science.gov (United States)

    Feldman, Uri; Doschek, G. A.; Seely, J. F.; Landi, E.; Dammasch, I.

    , 1.4x106 and 3x106 K. At the transition region (2x104 -2x105 K) where the structures are not isothermal the slopes of the emission measure vs. temperature stay the same independent of the solar activity. In our talk we will propose a variation to the EM method for the determination of the solar irradiance described above. The modified method will be based on line intensity calculations from the actual solar EM values at the above specified discrete temperatures. The EM in those temperatures could in principle be derived from solar observations spanning a fairly limited wavelengths range.

  3. Application of Monte Carlo method in determination of air absorbed rate from a full γ-ray spectrum

    International Nuclear Information System (INIS)

    Zhang Jiangyun; Huang Ning; Tang Lili; Liu Yanfang; Zhang Guanghua

    2011-01-01

    The dosimetric properties of a gamma-radiation field can be measured by a dose-rate meter or by a gamma-spectrometer with spectrum-dose conversion. One of the spectrum dose conversion methods is to evaluate the radiation dose directly from integrating the observed pulse height spectrum weighted by a G(E) function, instead of making spectrum analysis.In this paper,energy spectra of 11 single energy point sources in 0.1-2.5 MeV are simulated by using Monte Carlo software MCNP5 for NaI(Tl) detectors of Φ 75 mm x 75 mm, Φ 50 mm x 50 mm and Φ 25 mm x 25 mm. The energy spectra are used as standard spectrum to calculate the G(E) value, so as to calculate corresponding doses. Comparing the results with theoretical value,the error is less than 1.5%. Finally, the G(E)-based γ dose rate of radiation field agreed well (within 5%) with the dose rate measured by a dosimeter. (authors)

  4. A Proposal on the Advanced Sampling Based Sensitivity and Uncertainty Analysis Method for the Eigenvalue Uncertainty Analysis

    International Nuclear Information System (INIS)

    Kim, Song Hyun; Song, Myung Sub; Shin, Chang Ho; Noh, Jae Man

    2014-01-01

    In using the perturbation theory, the uncertainty of the response can be estimated by a single transport simulation, and therefore it requires small computational load. However, it has a disadvantage that the computation methodology must be modified whenever estimating different response type such as multiplication factor, flux, or power distribution. Hence, it is suitable for analyzing few responses with lots of perturbed parameters. Statistical approach is a sampling based method which uses randomly sampled cross sections from covariance data for analyzing the uncertainty of the response. XSUSA is a code based on the statistical approach. The cross sections are only modified with the sampling based method; thus, general transport codes can be directly utilized for the S/U analysis without any code modifications. However, to calculate the uncertainty distribution from the result, code simulation should be enough repeated with randomly sampled cross sections. Therefore, this inefficiency is known as a disadvantage of the stochastic method. In this study, an advanced sampling method of the cross sections is proposed and verified to increase the estimation efficiency of the sampling based method. In this study, to increase the estimation efficiency of the sampling based S/U method, an advanced sampling and estimation method was proposed. The main feature of the proposed method is that the cross section averaged from each single sampled cross section is used. For the use of the proposed method, the validation was performed using the perturbation theory

  5. Accelerated one-step generation of full-color holographic videos using a color-tunable novel-look-up-table method for holographic three-dimensional television broadcasting

    OpenAIRE

    Kim, Seung-Cheol; Dong, Xiao-Bin; Kim, Eun-Soo

    2015-01-01

    A color-tunable novel-look-up-table (CT-NLUT) for fast one-step calculation of full-color computer-generated holograms is proposed. The proposed method is composed of four principal fringe patterns (PFPs) such as a baseline, a depth-compensating and two color-compensating PFPs. CGH patterns for one color are calculated by combined use of baseline-PFP and depth-compensating-PFP and from them, those for two other colors are generated by being multiplied by the corresponding color-compensating-P...

  6. Standardized patients in audiology: a proposal for a new method of evaluating clinical competence.

    Science.gov (United States)

    Dinsmore, Brooke Freeman; Bohnert, Carrie; Preminger, Jill E

    2013-05-01

    While accrediting organizations require AuD programs to provide evidence that their students are able to demonstrate knowledge and competencies in specific content areas, there are no generally accepted mechanisms for the assessment and the measurement of these proficiencies. We propose that AuD programs consider developing standardized patient (SP) cases in order to develop consistent summative assessment programs within and across universities. The purpose of this article is to provide a framework for establishing SP programs to evaluate competencies in AuD students by detailing the history of SP cases and their use, developing a rationale for this method of assessment, and outlining the steps for writing and implementing SP cases. Literature review. SPs have been used to assess clinical competence in medical students for over 50 yr. The prevalence of SP assessment in allied health professions (e.g., dentistry, psychology, pharmacy) has increased over the last two decades but has only gained a limited following in audiology. SP assessment has been implemented in medical education using the Objective Structured Clinical Examination, a multistation, timed exam that uses fictional cases to assess students' clinical abilities. To date, only one published report has been completed that evaluates the use of SPs to assess clinical abilities in audiology students. This article expands upon the work of English et al (2007) and their efforts to use SPs to evaluate counseling abilities. To this end, we describe the steps necessary to write a case, procedures to determine performance requirements, and the need to develop remediation plans. As an example, we include a case that we have developed in order to evaluate vestibular assessment and patient communication skills. Utilizing SP assessment in audiology education would provide useful means to evaluate competence in a uniform way. Future research is necessary to develop reliable and valid cases that may be implemented

  7. Proposing New Methods to Enhance the Low-Resolution Simulated GPR Responses in the Frequency and Wavelet Domains

    Directory of Open Access Journals (Sweden)

    Reza Ahmadi

    2014-12-01

    Full Text Available To date, a number of numerical methods, including the popular Finite-Difference Time Domain (FDTD technique, have been proposed to simulate Ground-Penetrating Radar (GPR responses. Despite having a number of advantages, the finite-difference method also has pitfalls such as being very time consuming in simulating the most common case of media with high dielectric permittivity, causing the forward modelling process to be very long lasting, even with modern high-speed computers. In the present study the well-known hyperbolic pattern response of horizontal cylinders, usually found in GPR B-Scan images, is used as a basic model to examine the possibility of reducing the forward modelling execution time. In general, the simulated GPR traces of common reflected objects are time shifted, as with the Normal Moveout (NMO traces encountered in seismic reflection responses. This suggests the application of Fourier transform to the GPR traces, employing the time-shifting property of the transformation to interpolate the traces between the adjusted traces in the frequency domain (FD. Therefore, in the present study two post-processing algorithms have been adopted to increase the speed of forward modelling while maintaining the required precision. The first approach is based on linear interpolation in the Fourier domain, resulting in increasing lateral trace-to-trace interval of appropriate sampling frequency of the signal, preventing any aliasing. In the second approach, a super-resolution algorithm based on 2D-wavelet transform is developed to increase both vertical and horizontal resolution of the GPR B-Scan images through preserving scale and shape of hidden hyperbola features. Through comparing outputs from both methods with the corresponding actual high-resolution forward response, it is shown that both approaches can perform satisfactorily, although the wavelet-based approach outperforms the frequency-domain approach noticeably, both in amplitude and

  8. A Proposal of Product Development Collaboration Method Using User Support Information and its Experimental Evaluation

    Science.gov (United States)

    Tanaka, Mitsuru; Kataoka, Masatoshi; Koizumi, Hisao

    As the market changes more rapidly and new products continue to get more complex and multifunctional, product development collaboration with competent partners and leading users is getting more important to come up with new products that are successful in the market in a timely manner. ECM (engineering chain management) and SCM (supply chain management) are supply-side approaches toward this collaboration. In this paper, we propose a demand-side approach toward product development collaboration with users based on the information gathered through user support interactions. The approach and methodology proposed here was applied to a real data set, and its effectiveness was verified.

  9. A Proposed Model of Retransformed Qualitative Data within a Mixed Methods Research Design

    Science.gov (United States)

    Palladino, John M.

    2009-01-01

    Most models of mixed methods research design provide equal emphasis of qualitative and quantitative data analyses and interpretation. Other models stress one method more than the other. The present article is a discourse about the investigator's decision to employ a mixed method design to examine special education teachers' advocacy and…

  10. Characterization of full set material constants of piezoelectric materials based on ultrasonic method and inverse impedance spectroscopy using only one sample.

    Science.gov (United States)

    Li, Shiyang; Zheng, Limei; Jiang, Wenhua; Sahul, Raffi; Gopalan, Venkatraman; Cao, Wenwu

    2013-09-14

    The most difficult task in the characterization of complete set material properties for piezoelectric materials is self-consistency. Because there are many independent elastic, dielectric, and piezoelectric constants, several samples are needed to obtain the full set constants. Property variation from sample to sample often makes the obtained data set lack of self-consistency. Here, we present a method, based on pulse-echo ultrasound and inverse impedance spectroscopy, to precisely determine the full set physical properties of piezoelectric materials using only one small sample, which eliminated the sample to sample variation problem to guarantee self-consistency. The method has been applied to characterize the [001] C poled Mn modified 0.27Pb(In 1/2 Nb 1/2 )O 3 -0.46Pb(Mg 1/3 Nb 2/3 )O 3 -0.27PbTiO 3 single crystal and the validity of the measured data is confirmed by a previously established method. For the inverse calculations using impedance spectrum, the stability of reconstructed results is analyzed by fluctuation analysis of input data. In contrast to conventional regression methods, our method here takes the full advantage of both ultrasonic and inverse impedance spectroscopy methods to extract all constants from only one small sample. The method provides a powerful tool for assisting novel piezoelectric materials of small size and for generating needed input data sets for device designs using finite element simulations.

  11. A Method of Estimating Pressure and Intensity Distributions of Multielement Phased Array High Intensity Focused Ultrasonic Field at Full Power Using a Needle Hydrophone

    International Nuclear Information System (INIS)

    Yu Ying; Shen Guofeng; Bai Jingfeng; Chen Yazhu

    2011-01-01

    The pressure and intensity distribution of high intensity focused ultrasound (HIFU) fields at full power are critical for predicting heating patterns and ensuring safety of the therapy. With the limitations of maximum pressure at the hydrophone and damage from cavitation or thermal effects, it is hard to measure pressure and intensity directly when HIFU is at full power. HIFU-phased arrays are usually composed of large numbers of small elements and the sound power radiated from some of them at full power is measureable using a hydrophone, we grouped them based on the limitation of maximum permissible pressure at the hydrophone and the characteristics of the element arrangement in the array. Then sound field measurement of the group was carried out at full power level. Using the acoustic coherence principle, the pressure and intensity distribution of the array at full power level can be calculated from corresponding values from the groups. With this method, computer simulations and sound field measurement of a 65-element concentric distributed phased array was carried out. The simulation results demonstrate theoretically the feasibility of this method. Measurements on the 65-element phased array also verify the effectiveness of this method for estimating the pressure and intensity distribution of phased array at full power level using a needle hydrophone.

  12. STANDARD METHODS FOR THE DETERMINATION OF THE RUNWAY AND SEAKEEPING CHARACTERISTICS OF A SEAPLANE ON THE WATERS DURING FULL-SCALE TESTS

    Directory of Open Access Journals (Sweden)

    A. A. Khokhlov

    2015-01-01

    Full Text Available One of the main stages of the creation of seaplanes and amphibious aircraft are flight certification tests, including tests to determine their landing and sailing characteristics on the water. In accordance with aviation regulations (part 21 certification work is carried out according to the methods of determination of compliance (MOC, which are the main organizational and methodological document for testing. The paper discusses the main provisions of the standard methods for the determination of the runway and sea keeping characteristics of seaplanes and amphibians on water areas with full-scale tests.

  13. Proposal on the mitigation methods of thermal stress near the sodium

    International Nuclear Information System (INIS)

    Ando, Masanori; Kasahara, Naoto

    2003-09-01

    A Reactor vessel of fast rector plants contains high temperature liquid sodium in its inside and its upper end is supported by a low temperature structures. Therefore, a significant temperature gradient will arise at the vessel wall near the sodium surface. For this reason, a large thermal stress will be generated around this part. To lower this stress and to protect the vessel, a number of methods have been applied the plants. Generally, these mitigation methods by protection equipments for thermal stress also have some problems such as, increase a mount of materials or to be complicate for control, hard to maintenance and so on. In this research, authors suggested another simple methods for thermal stress, and evaluated their effects using computer analysis. The results obtained in this research are as follows. Authors suggested one method, circulate high temperature gas around outside of the vessel and evaluated the effects of this method by analysis. In case of using this method, Sn (one of index values of design) value might be getting lower about 45%. Authors also suggested another method by setting up a heat transfer plate outside of the vessel and evaluated the effects of this method by analysis. Effects of this method depend on material of the plate. In case of using Carbon as material of plate, Sn value might be 27% lower and in case of using 12Cr steel as material of plate, Sn value might be 15% lower. Authors also suggested another method by changing material of the guard vessel to be the one which has good ability of heat transfer and evaluated the effects of this method by analysis. In case of changing material of guard vessel to 12Cr steel, Sn value might be lower about 12%. (author)

  14. Proposing water balance method for water availability estimation in Indonesian regional spatial planning

    Science.gov (United States)

    Juniati, A. T.; Sutjiningsih, D.; Soeryantono, H.; Kusratmoko, E.

    2018-01-01

    The water availability (WA) of a region is one of important consideration in both the formulation of spatial plans and the evaluation of the effectiveness of actual land use in providing sustainable water resources. Information on land-water needs vis-a-vis their availability in a region determines the state of the surplus or deficit to inform effective land use utilization. How to calculate water availability have been described in the Guideline in Determining the Carrying Capacity of the Environment in Regional Spatial Planning. However, the method of determining the supply and demand of water on these guidelines is debatable since the determination of WA in this guideline used a rational method. The rational method is developed the basis for storm drain design practice and it is essentially a peak discharge method peak discharge calculation method. This paper review the literature in methods of water availability estimation which is described descriptively, and present arguments to claim that water balance method is a more fundamental and appropriate tool in water availability estimation. A better water availability estimation method would serve to improve the practice in preparing formulations of Regional Spatial Plan (RSP) as well as evaluating land use capacity in providing sustainable water resources.

  15. New proposal of moderator temperature coefficient estimation method using gray-box model in NPP, (1)

    International Nuclear Information System (INIS)

    Mori, Michitsugu; Kagami, Yuichi; Kanemoto, Shigeru; Enomoto, Mitsuhiro; Tamaoki, Tetsuo; Kawamura, Shinichiro

    2004-01-01

    The purpose of the present paper is to establish a new void reactivity coefficient (VRC) estimation method based on gray box modeling concept. The gray box model consists of a point kinetics model as the first principle model and a fitting model of moderator temperature kinetics. Applying Kalman filter and maximum likehood estimation algorithms to the gray box model, MTC can be estimated. The verification test is done by Monte Carlo simulation, and, it is shown that the present method gives the best estimation results comparing with the conventional methods from the viewpoints of non-biased and smallest scattering estimation performance. Furthermore, the method is verified via real plant data analysis. The reason of good performance of the present method is explained by proper definition of likelihood function based on explicit expression of observation and system noise in the gray box model. (author)

  16. A proposal of parameter determination method in the residual strength degradation model for the prediction of fatigue life (I)

    International Nuclear Information System (INIS)

    Kim, Sang Tae; Jang, Seong Soo

    2001-01-01

    The static and fatigue tests have been carried out to verify the validity of a generalized residual strength degradation model. And a new method of parameter determination in the model is verified experimentally to account for the effect of tension-compression fatigue loading of spheroidal graphite cast iron. It is shown that the correlation between the experimental results and the theoretical prediction on the statistical distribution of fatigue life by using the proposed method is very reasonable. Furthermore, it is found that the correlation between the theoretical prediction and the experimental results of fatigue life in case of tension-tension fatigue data in composite material appears to be reasonable. Therefore, the proposed method is more adjustable in the determination of the parameter than maximum likelihood method and minimization technique

  17. Assessment of four calculation methods proposed by the EC for waste hazardous property HP 14 'Ecotoxic'.

    Science.gov (United States)

    Hennebert, Pierre; Humez, Nicolas; Conche, Isabelle; Bishop, Ian; Rebischung, Flore

    2016-02-01

    Legislation published in December 2014 revised both the List of Waste (LoW) and amended Appendix III of the revised Waste Framework Directive 2008/98/EC; the latter redefined hazardous properties HP 1 to HP 13 and HP 15 but left the assessment of HP 14 unchanged to allow time for the Directorate General of the Environment of the European Commission to complete a study that is examining the impacts of four different calculation methods for the assessment of HP 14. This paper is a contribution to the assessment of the four calculation methods. It also includes the results of a fifth calculation method; referred to as "Method 2 with extended M-factors". Two sets of data were utilised in the assessment; the first (Data Set #1) comprised analytical data for 32 different waste streams (16 hazardous (H), 9 non-hazardous (NH) and 7 mirror entries, as classified by the LoW) while the second data set (Data Set #2), supplied by the eco industries, comprised analytical data for 88 waste streams, all classified as hazardous (H) by the LoW. Two approaches were used to assess the five calculation methods. The first approach assessed the relative ranking of the five calculation methods by the frequency of their classification of waste streams as H. The relative ranking of the five methods (from most severe to less severe) is: Method 3>Method 1>Method 2 with extended M-factors>Method 2>Method 4. This reflects the arithmetic ranking of the concentration limits of each method when assuming M=10, and is independent of the waste streams, or the H/NH/Mirror status of the waste streams. A second approach is the absolute matching or concordance with the LoW. The LoW is taken as a reference method and the H wastes are all supposed to be HP 14. This point is discussed in the paper. The concordance for one calculation method is established by the number of wastes with identical classification by the considered calculation method and the LoW (i.e. H to H, NH to NH). The discordance is

  18. A proposed method of measuring the electric-dipole moment of the neutron by ultracold neutron interferometry

    International Nuclear Information System (INIS)

    Freedman, M.S.; Peshkin, M.; Ringo, G.R.; Dombeck, T.W.

    1989-08-01

    The use of an ultracold neutron interferometer incorporating an electrostatic accelerator having a strong electric field gradient to accelerate neutrons by their possible electric dipole moment is proposed as a method of measuring the neutron electric dipole moment. The method appears to have the possibility of extending the sensitivity of the measurement by several orders of magnitude, perhaps to 10 -30 e-cm. 9 refs., 3 figs

  19. Small Private Online Research: A Proposal for A Numerical Methods Course Based on Technology Use and Blended Learning

    Science.gov (United States)

    Cepeda, Francisco Javier Delgado

    2017-01-01

    This work presents a proposed model in blended learning for a numerical methods course evolved from traditional teaching into a research lab in scientific visualization. The blended learning approach sets a differentiated and flexible scheme based on a mobile setup and face to face sessions centered on a net of research challenges. Model is…

  20. Enhancing the Social Network Dimension of Lifelong Competence Development and Management Systems: A Proposal of Methods and Tools

    NARCIS (Netherlands)

    Cheak, Alicia; Angehrn, Albert; Sloep, Peter

    2006-01-01

    Cheak, A. M., Angehrn, A. A., & Sloep, P. (2006). Enhancing the social network dimension of lifelong competence development and management systems: A proposal of methods and tools. In R. Koper & K. Stefanov (Eds.). Proceedings of International Workshop in Learning Networks for Lifelong Competence

  1. Enhancing the Social Network Dimension of Lifelong Competence Development and Management Systems: A proposal of methods and tools

    NARCIS (Netherlands)

    Cheak, Alicia; Angehrn, Albert; Sloep, Peter

    2006-01-01

    Cheak, A. M., Angehrn, A. A., & Sloep, P. B. (2006). Enhancing the social network dimension of lifelong competence development and management systems: A proposal of methods and tools. In E. J. R. Koper & K. Stefanov (Eds.), Proceedings of International Workshop on Learning Networks for Lifelong

  2. Proposal for a new method of reactor neutron flux distribution determination

    Energy Technology Data Exchange (ETDEWEB)

    Popic, V R [Institute of nuclear sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

    1964-01-15

    A method, based on the measurements of the activity produced in a medium flowing with variable velocity through a reactor, for the determination of the neutron flux distribution inside a reactor is considered theoretically (author)

  3. Proposal for Reduction of Calibration Process in Reference to Trip Distribution Method

    Directory of Open Access Journals (Sweden)

    Katalin Tanczos

    2009-01-01

    Full Text Available The nowadays applied different macro models or parts ofthose, which describe the urban environment, can originate in afour-step modelling process. The paper focuses on the trip distributionprocess (the 2"d step because of its significant calibrationrequirements. Therefore, it is possible to make the entiremodelling process more reliable (dependent upon the reliabilityof the available databases .

  4. Conceptual design of covering method for the proposed LILW near-surface repository at Cernavoda

    International Nuclear Information System (INIS)

    Diaconu, Daniela

    2003-01-01

    The disposal concept of the low and intermediate level (LIL) wastes resulting during NPP operation combines both the natural and engineered barriers in order to ensure the safety of the environment and population. Saligny site has been proposed for LIL waste disposal. Preliminary performance assessments indicate that the loess and clay layers are efficient natural barriers against water flow and radionuclide migration through the vadose zone to the local aquifers. At present, the studies on site characterization are concentrated on investigation of the potential factors affecting the long-term integrity of the disposal facility. This analysis showed that surface erosion by wind and water and bio-intrusion by plant roots and burrowing animals could affect the long-term disposal safety. Based on the preliminary erosion results, as well as on the high probability of bio-intrusion by the plant roots and burrowing animals (i.e. moles, mice), different covering systems able to ensure the long-term safety of the repository has been proposed and analyzed. FEHM and HYDRUS 2D water flow simulations have been performed in order to compare their efficiency in the diminution of the infiltration rate in the repository. From this point of view, the covering system combining the capillary barrier and the resistive layer proved to have the best behavior

  5. Effects of different surface-treatment methods on the bond strengths of resin cements to full-ceramic systems

    Directory of Open Access Journals (Sweden)

    Gülay Kansu

    2011-09-01

    Conclusions: The in vitro findings from this study indicate that surface-treatment procedures applied to the IPS Empress and the IPS Empress 2 full-ceramic systems are important when cement types are considered. In contrast, cement types and surface-treatment methods had no effect on changing the bond strength of the In-Ceram ceramic system.

  6. A fast and robust method for full genome sequencing of Porcine Reproductive and Respiratory Syndrome Virus (PRRSV) Type 1 and Type 2

    DEFF Research Database (Denmark)

    Kvisgaard, Lise Kirstine; Hjulsager, Charlotte Kristiane; Fahnøe, Ulrik

    2013-01-01

    . In the present study, fast and robust methods for long range RT-PCR amplification and subsequent next generation sequencing (NGS) were developed and validated on nine Type 1 and nine Type 2 PRRSV viruses. The methods generated robust and reliable sequences both on primary material and cell culture adapted...... viruses and the protocols performed well on all three NGS platforms tested (Roche 454 FLX, Illumina HiSeq2000, and Ion Torrent PGM™ Sequencer). These methods will greatly facilitate the generation of more full genome PRRSV sequences globally....

  7. Calculation of evolutionary correlation between individual genes and full-length genome: a method useful for choosing phylogenetic markers for molecular epidemiology.

    Directory of Open Access Journals (Sweden)

    Shuai Wang

    Full Text Available Individual genes or regions are still commonly used to estimate the phylogenetic relationships among viral isolates. The genomic regions that can faithfully provide assessments consistent with those predicted with full-length genome sequences would be preferable to serve as good candidates of the phylogenetic markers for molecular epidemiological studies of many viruses. Here we employed a statistical method to evaluate the evolutionary relationships between individual viral genes and full-length genomes without tree construction as a way to determine which gene can match the genome well in phylogenetic analyses. This method was performed by calculation of linear correlations between the genetic distance matrices of aligned individual gene sequences and aligned genome sequences. We applied this method to the phylogenetic analyses of porcine circovirus 2 (PCV2, measles virus (MV, hepatitis E virus (HEV and Japanese encephalitis virus (JEV. Phylogenetic trees were constructed for comparisons and the possible factors affecting the method accuracy were also discussed in the calculations. The results revealed that this method could produce results consistent with those of previous studies about the proper consensus sequences that could be successfully used as phylogenetic markers. And our results also suggested that these evolutionary correlations could provide useful information for identifying genes that could be used effectively to infer the genetic relationships.

  8. Proposing co-design of personas as a method to heighten validity and engage users

    DEFF Research Database (Denmark)

    Albrechtsen, Charlotte; Pedersen, Majbrit; Pedersen, Nicholai Friis

    2016-01-01

    This paper proposes co-designing personas with users as a strategy to overcome a challenge inherent in the design of personas or fictitious users: On one hand, personas should appear realistic and believable as individuals, and on the other hand, personas should represent a broader range of users....... By involving empirical users in all parts of the process of persona design, the risk of creating personas that are too stereotypical is minimized, as the participating users enrich the data on which the personas are based with up-to-date and firsthand contextual knowledge. Advantages of co-designing personas...... with users is illustrated by a case from higher education in which personas were co-designed with students as part of a project aiming at designing a smartphone application for Master's thesis students. © 2016, IGI Global....

  9. R and D proposals to improve outages operation. Methods, practices and tools

    International Nuclear Information System (INIS)

    Dionis, Francois

    2014-01-01

    This paper deals with outage operation improvement. It offers a number of tracks on the interactions between the operation activities and maintenance, with a methodological perspective and proposals concerning the Information System. On the methodological point of view, a clever plant systems modeling may allow representing the needed characteristics in order to optimize tagouts, alignment procedures and the schedule. Tools must be taken n into account for new tagout practices such as tags sharing. It is possible to take advantage of 2D drawings integrated into the information system in order to improve the data controls and to visualize operation activities. An integrated set of mobile applications should allow field operators to join the information system for a better and safer performance. (author)

  10. Proposed method for determining the thickness of glass in solar collector panels

    Science.gov (United States)

    Moore, D. M.

    1980-01-01

    An analytical method was developed for determining the minimum thickness for simply supported, rectangular glass plates subjected to uniform normal pressure environmental loads such as wind, earthquake, snow, and deadweight. The method consists of comparing an analytical prediction of the stress in the glass panel to a glass breakage stress determined from fracture mechanics considerations. Based on extensive analysis using the nonlinear finite element structural analysis program ARGUS, design curves for the structural analysis of simply supported rectangular plates were developed. These curves yield the center deflection, center stress and corner stress as a function of a dimensionless parameter describing the load intensity. A method of estimating the glass breakage stress as a function of a specified failure rate, degree of glass temper, design life, load duration time, and panel size is also presented.

  11. Brief communication: a proposed osteological method for the estimation of pubertal stage in human skeletal remains.

    Science.gov (United States)

    Shapland, Fiona; Lewis, Mary E

    2013-06-01

    Puberty forms an important threshold between childhood and adulthood, but this subject has received little attention in bioarchaeology. The new application of clinical methods to assess pubertal stage in adolescent skeletal remains is explored, concentrating on the development of the mandibular canine, hamate, hand phalanges, iliac crest and distal radius. Initial results from the medieval cemetery of St. Peter's Church, Barton-upon-Humber, England suggest that application of these methods may provide insights into aspects of adolescent development. This analysis indicates that adolescents from this medieval site were entering the pubertal growth spurt at a similar age to their modern counterparts, but that the later stages of pubertal maturation were being significantly delayed, perhaps due to environmental stress. Continued testing and refinement of these methods on living adolescents is still necessary to improve our understanding of their significance and accuracy in predicting pubertal stages. Copyright © 2013 Wiley Periodicals, Inc.

  12. Hypothesis: primary antiangiogenic method proposed to treat early stage breast cancer

    International Nuclear Information System (INIS)

    Retsky, Michael W; Hrushesky, William JM; Gukas, Isaac D

    2009-01-01

    Women with Down syndrome very rarely develop breast cancer even though they now live to an age when it normally occurs. This may be related to the fact that Down syndrome persons have an additional copy of chromosome 21 where the gene that codes for the antiangiogenic protein Endostatin is located. Can this information lead to a primary antiangiogenic therapy for early stage breast cancer that indefinitely prolongs remission? A key question that arises is when is the initial angiogenic switch thrown in micrometastases? We have conjectured that avascular micrometastases are dormant and relatively stable if undisturbed but that for some patients angiogenesis is precipitated by surgery. We also proposed that angiogenesis of micrometastases very rarely occurs before surgical removal of the primary tumor. If that is so, it seems possible that we could suggest a primary antiangiogenic therapy but the problem then arises that starting a therapy before surgery would interfere with wound healing. The therapy must be initiated at least one day prior to surgical removal of the primary tumor and kept at a Down syndrome level perhaps indefinitely. That means the drug must have virtually no toxicity and not interfere meaningfully with wound healing. This specifically excludes drugs that significantly inhibit the VEGF pathway since that is important for wound healing and because these agents have some toxicity. Endostatin is apparently non-toxic and does not significantly interfere with wound healing since Down syndrome patients have no abnormal wound healing problems. We propose a therapy for early stage breast cancer consisting of Endostatin at or above Down syndrome levels starting at least one day before surgery and continuing at that level. This should prevent micrometastatic angiogenesis resulting from surgery or at any time later. Adjuvant chemotherapy or hormone therapy should not be necessary. This can be continued indefinitely since there is no acquired resistance that

  13. About the use of the Monte-Carlo code based tracing algorithm and the volume fraction method for S n full core calculations

    Energy Technology Data Exchange (ETDEWEB)

    Gurevich, M. I.; Oleynik, D. S. [RRC Kurchatov Inst., Kurchatov Sq., 1, 123182, Moscow (Russian Federation); Russkov, A. A.; Voloschenko, A. M. [Keldysh Inst. of Applied Mathematics, Miusskaya Sq., 4, 125047, Moscow (Russian Federation)

    2006-07-01

    The tracing algorithm that is implemented in the geometrical module of Monte-Carlo transport code MCU is applied to calculate the volume fractions of original materials by spatial cells of the mesh that overlays problem geometry. In this way the 3D combinatorial geometry presentation of the problem geometry, used by MCU code, is transformed to the user defined 2D or 3D bit-mapped ones. Next, these data are used in the volume fraction (VF) method to approximate problem geometry by introducing additional mixtures for spatial cells, where a few original materials are included. We have found that in solving realistic 2D and 3D core problems a sufficiently fast convergence of the VF method takes place if the spatial mesh is refined. Virtually, the proposed variant of implementation of the VF method seems as a suitable geometry interface between Monte-Carlo and S{sub n} transport codes. (authors)

  14. Proposed method of assembly for the BCD silicon strip vertex detector modules

    International Nuclear Information System (INIS)

    Lindenmeyer, C.

    1989-01-01

    The BCD Silicon strip Vertex Detector is constructed of 10 identical central region modules and 18 similar forward region modules. This memo describes a method of assembling these modules from individual silicon wafers. Each wafer is fitted with associated front end electronics and cables and has been tested to insure that only good wafers reach the final assembly stage. 5 figs

  15. Interpreting Statistical Significance Test Results: A Proposed New "What If" Method.

    Science.gov (United States)

    Kieffer, Kevin M.; Thompson, Bruce

    As the 1994 publication manual of the American Psychological Association emphasized, "p" values are affected by sample size. As a result, it can be helpful to interpret the results of statistical significant tests in a sample size context by conducting so-called "what if" analyses. However, these methods can be inaccurate…

  16. Texting to increase physical activity among teenagers (TXT Me!): Rationale, design, and methods proposal

    Science.gov (United States)

    Physical activity decreases from childhood through adulthood. Among youth, teenagers (teens) achieve the lowest levels of physical activity, and high school age youth are particularly at risk of inactivity. Effective methods are needed to increase youth physical activity in a way that can be maintai...

  17. Elliptical broken line method for calculating capillary density in nailfold capillaroscopy: Proposal and evaluation.

    Science.gov (United States)

    Karbalaie, Abdolamir; Abtahi, Farhad; Fatemi, Alimohammad; Etehadtavakol, Mahnaz; Emrani, Zahra; Erlandsson, Björn-Erik

    2017-09-01

    Nailfold capillaroscopy is a practical method for identifying and obtaining morphological changes in capillaries which might reveal relevant information about diseases and health. Capillaroscopy is harmless, and seems simple and repeatable. However, there is lack of established guidelines and instructions for acquisition as well as the interpretation of the obtained images; which might lead to various ambiguities. In addition, assessment and interpretation of the acquired images are very subjective. In an attempt to overcome some of these problems, in this study a new modified technique for assessment of nailfold capillary density is introduced. The new method is named elliptic broken line (EBL) which is an extension of the two previously known methods by defining clear criteria for finding the apex of capillaries in different scenarios by using a fitted elliptic. A graphical user interface (GUI) is developed for pre-processing, manual assessment of capillary apexes and automatic correction of selected apexes based on 90° rule. Intra- and inter-observer reliability of EBL and corrected EBL is evaluated in this study. Four independent observers familiar with capillaroscopy performed the assessment for 200 nailfold videocapillaroscopy images, form healthy subject and systemic lupus erythematosus patients, in two different sessions. The results show elevation from moderate (ICC=0.691) and good (ICC=0.753) agreements to good (ICC=0.750) and good (ICC=0.801) for intra- and inter-observer reliability after automatic correction of EBL. This clearly shows the potential of this method to improve the reliability and repeatability of assessment which motivates us for further development of automatic tool for EBL method. Copyright © 2017 Elsevier Inc. All rights reserved.

  18. New clinical validation method for automated sphygmomanometer: a proposal by Japan ISO-WG for sphygmomanometer standard.

    Science.gov (United States)

    Shirasaki, Osamu; Asou, Yosuke; Takahashi, Yukio

    2007-12-01

    Owing to fast or stepwise cuff deflation, or measuring at places other than the upper arm, the clinical accuracy of most recent automated sphygmomanometers (auto-BPMs) cannot be validated by one-arm simultaneous comparison, which would be the only accurate validation method based on auscultation. Two main alternative methods are provided by current standards, that is, two-arm simultaneous comparison (method 1) and one-arm sequential comparison (method 2); however, the accuracy of these validation methods might not be sufficient to compensate for the suspicious accuracy in lateral blood pressure (BP) differences (LD) and/or BP variations (BPV) between the device and reference readings. Thus, the Japan ISO-WG for sphygmomanometer standards has been studying a new method that might improve validation accuracy (method 3). The purpose of this study is to determine the appropriateness of method 3 by comparing immunity to LD and BPV with those of the current validation methods (methods 1 and 2). The validation accuracy of the above three methods was assessed in human participants [N=120, 45+/-15.3 years (mean+/-SD)]. An oscillometric automated monitor, Omron HEM-762, was used as the tested device. When compared with the others, methods 1 and 3 showed a smaller intra-individual standard deviation of device error (SD1), suggesting their higher reproducibility of validation. The SD1 by method 2 (P=0.004) significantly correlated with the participant's BP, supporting our hypothesis that the increased SD of device error by method 2 is at least partially caused by essential BPV. Method 3 showed a significantly (P=0.0044) smaller interparticipant SD of device error (SD2), suggesting its higher interparticipant consistency of validation. Among the methods of validation of the clinical accuracy of auto-BPMs, method 3, which showed the highest reproducibility and highest interparticipant consistency, can be proposed as being the most appropriate.

  19. An Innovative Oil Pollution Containment Method for Ship Wrecks Proposed for Offshore Well Blow-outs

    OpenAIRE

    ANDRITSOS Fivos; COJINS Hans

    2011-01-01

    In the aftermath of the PRESTIGE disaster, an innovative system for the prompt intervention on oil pollution sources (primarily ship wrecks) at great depths was conceived at the Joint Research Center of the European Commission. This system, with some re-engineering, could also serve for collecting oil and gas leaking after an offshore well blow-out and could constitute a reference method for prompt intervention on deep water oil pollution sources like ship wrecks and blown-out offshore wells....

  20. [Proposal of a method for collective analysis of work-related accidents in the hospital setting].

    Science.gov (United States)

    Osório, Claudia; Machado, Jorge Mesquita Huet; Minayo-Gomez, Carlos

    2005-01-01

    The article presents a method for the analysis of work-related accidents in hospitals, with the double aim of analyzing accidents in light of actual work activity and enhancing the vitality of the various professions that comprise hospital work. This process involves both research and intervention, combining knowledge output with training of health professionals, fostering expanded participation by workers in managing their daily work. The method consists of stimulating workers to recreate the situation in which a given accident occurred, shifting themselves to the position of observers of their own work. In the first stage of analysis, workers are asked to show the work analyst how the accident occurred; in the second stage, the work accident victim and analyst jointly record the described series of events in a diagram; in the third, the resulting record is re-discussed and further elaborated; in the fourth, the work accident victim and analyst evaluate and implement measures aimed to prevent the accident from recurring. The article concludes by discussing the method's possibilities and limitations in the hospital setting.

  1. [Proposal of a conceptual method of supportive care for co-active patients].

    Science.gov (United States)

    Abidli, Yamine; Piette, Danielle; Casini, Annalisa

    2015-01-01

    There is a broad consensus on the importance for health professionals to support co-active patients. However, in practice, very few "patient care partnership" approaches have been developed. We hypothesized that the lack of investment in supporting patient care partnerships is due to the lack of interest in the skills needed by caregivers to provide such support. This paper intends to address thisgap. The patient care partnership method is studied, adapted and developed from existing models. It complements, harmonizes and integrates various schools of thought arising from the need to place the patient at the center of care and life in general. The patient care partnership method includes 7 stages during which the professional accompanies the patient through the process of care. The methodological approach for training professionals is designed to ensure that professionals experience the change as well as its difficulties of the change they expect from the patient in the care relationship. This method now needs to be validated by the experience of other professionals in order define the limits of application and to allow further development.

  2. Method for the proposal and evaluation of urban structures for compact cities using an expert system

    Directory of Open Access Journals (Sweden)

    Shirou Tsuboi

    2016-12-01

    Full Text Available The world population is continually increasing, but the Japanese population is decreasing. By 2050, the Japanese population is calculated to be close to 100 million people, and by 2060, 40% of the Japanese are estimated to be aged 65 years or more. Data show an increase in the declining birth and aging rates of the population. The development of high-concentration urban structures will be needed to solve such problems. However, a detailed vision of the future is yet to be clarified and in the process of consideration. In this study, we developed an instrument called “Population Migration Tool,” which is based on plural planning and policy, after we formed a future population distribution model. In addition, We also established a high-concentration urban structure model with this tool with the aim of considering the kind of urban structure local cities should target in the future.

  3. Creep-fatigue evaluation method for weld joint of Mod.9Cr-1Mo steel Part II: Plate bending test and proposal of a simplified evaluation method

    Energy Technology Data Exchange (ETDEWEB)

    Ando, Masanori, E-mail: ando.masanori@jaea.go.jp; Takaya, Shigeru, E-mail: takaya.shigeru@jaea.go.jp

    2016-12-15

    Highlights: • Creep-fatigue evaluation method for weld joint of Mod.9Cr-1Mo steel is proposed. • A simplified evaluation method is also proposed for the codification. • Both proposed evaluation method was validated by the plate bending test. • For codification, the local stress and strain behavior was analyzed. - Abstract: In the present study, to develop an evaluation procedure and design rules for Mod.9Cr-1Mo steel weld joints, a method for evaluating the creep-fatigue life of Mod.9Cr-1Mo steel weld joints was proposed based on finite element analysis (FEA) and a series of cyclic plate bending tests of longitudinal and horizontal seamed plates. The strain concentration and redistribution behaviors were evaluated and the failure cycles were estimated using FEA by considering the test conditions and metallurgical discontinuities in the weld joints. Inelastic FEA models consisting of the base metal, heat-affected zone and weld metal were employed to estimate the elastic follow-up behavior caused by the metallurgical discontinuities. The elastic follow-up factors determined by comparing the elastic and inelastic FEA results were determined to be less than 1.5. Based on the estimated elastic follow-up factors obtained via inelastic FEA, a simplified technique using elastic FEA was proposed for evaluating the creep-fatigue life in Mod.9Cr-1Mo steel weld joints. The creep-fatigue life obtained using the plate bending test was compared to those estimated from the results of inelastic FEA and by a simplified evaluation method.

  4. Creep-fatigue evaluation method for weld joint of Mod.9Cr-1Mo steel Part II: Plate bending test and proposal of a simplified evaluation method

    International Nuclear Information System (INIS)

    Ando, Masanori; Takaya, Shigeru

    2016-01-01

    Highlights: • Creep-fatigue evaluation method for weld joint of Mod.9Cr-1Mo steel is proposed. • A simplified evaluation method is also proposed for the codification. • Both proposed evaluation method was validated by the plate bending test. • For codification, the local stress and strain behavior was analyzed. - Abstract: In the present study, to develop an evaluation procedure and design rules for Mod.9Cr-1Mo steel weld joints, a method for evaluating the creep-fatigue life of Mod.9Cr-1Mo steel weld joints was proposed based on finite element analysis (FEA) and a series of cyclic plate bending tests of longitudinal and horizontal seamed plates. The strain concentration and redistribution behaviors were evaluated and the failure cycles were estimated using FEA by considering the test conditions and metallurgical discontinuities in the weld joints. Inelastic FEA models consisting of the base metal, heat-affected zone and weld metal were employed to estimate the elastic follow-up behavior caused by the metallurgical discontinuities. The elastic follow-up factors determined by comparing the elastic and inelastic FEA results were determined to be less than 1.5. Based on the estimated elastic follow-up factors obtained via inelastic FEA, a simplified technique using elastic FEA was proposed for evaluating the creep-fatigue life in Mod.9Cr-1Mo steel weld joints. The creep-fatigue life obtained using the plate bending test was compared to those estimated from the results of inelastic FEA and by a simplified evaluation method.

  5. A proposal of a three-dimensional CT measurement method of maxillofacial structure

    International Nuclear Information System (INIS)

    Tanaka, Ray; Hayashi, Takafumi

    2007-01-01

    Three-dimensional CT measurement is put in practice in order to grasp the pathological condition on diseases such as the temporomandibular joint disorder, maxillofacial anomaly, jaw deformity, or fracture which cause the morphologic changes of the maxillofacial bones. On the 3D measurement, the unique system that is obtained by volume rendering 3D images with a simultaneous reference of axial images combined with coronal and sagittal multi-planar reconstruction (MPR) images (we call this MPR referential method), is employed in order to define the measurement points. Our purpose in this report is to indicate the usefulness of this unique method by comparing with the common way to define the measurement points on only 3D reconstruction images without consulting of MPR images. Clinical CT data obtained from a male patient with skeletal malocclusion was used. Contiguous axial images were reconstructed at 4 times magnification, with a reconstruction interval of 0.5 mm, focused on the temporomandibular joint region in his left side. After these images were converted to Digital Imaging and Communications in Medicine (DICOM) format and sent to personal computer (PC), 3D reconstruction image was created using free 3D DICOM medical image viewer. The coordinates of 3 measurement points (the lateral and medial pole of the mandibular condyle, and the left foramen ovale) were defined with MPR images (MPR coordinates) as reference coordinates, and then the coordinates that were defined on only 3D reconstruction image without consulting to MPR images (3D coordinates) were compared to those of MPR coordinates. Three examiners were engaged independently 10 times for every measurement point. In our result, there was no correspondence between 3D coordinates and MPR coordinates, and contribution of 3D coordinates showed a variety in every measurement point and in every observer. We deemed that ''MPR referential method'' is useful to assess the location of the target point of anatomical

  6. Proposed thermodynamic method to determine the vortex mass in layered superconductors

    International Nuclear Information System (INIS)

    Moler, K.A.; Fetter, A.L.; Kapitulnik, A.

    1995-01-01

    The authors describe a simple method to study vortex dynamics that can determine or set an upper limit on the vortex mass. The specific heat of the vortex lattice in layered superconductors has a classical limit of 1 k B per pancake vortex if the vortex mass is zero. If the vortex mass m v is finite, a new Einstein branch of normal modes will appear with a crossover temperature Θ E ∝ m v -1 , and the specific heat will saturate at a new classical limit of 2 k B per pancake vortex

  7. A proposal for a determination method of element division on an analytical model for finite element elastic waves propagation analysis

    International Nuclear Information System (INIS)

    Ishida, Hitoshi; Meshii, Toshiyuki

    2010-01-01

    This study proposes an element size selection method named the 'Impact-Meshing (IM) method' for a finite element waves propagation analysis model, which is characterized by (1) determination of element division of the model with strain energy in the whole model, (2) static analysis (dynamic analysis in a single time step) with boundary conditions which gives a maximum change of displacement in the time increment and inertial (impact) force caused by the displacement change. In this paper, an example of application of the IM method to 3D ultrasonic wave propagation problem in an elastic solid is described. These examples showed an analysis result with a model determined by the IM method was convergence and calculation time for determination of element subdivision was reduced to about 1/6 by the IM Method which did not need determination of element subdivision by a dynamic transient analysis with 100 time steps. (author)

  8. Fair and efficient tariffs for wind energy : principles, method, proposal, data and potential consequences in France

    International Nuclear Information System (INIS)

    Chabot, B.

    2001-01-01

    In 2000, the government of France announced a national energy plan that included the installation of 5,000 to 10,000 MW of wind power by 2010. It also announced a new system based on fixed tariffs that would replace the EOLE 2005 calls for tenders for projects under 12 MW. This paper described the principles and methods used to develop this fair and efficient tariff system for wind energy in France. The Agence de l'Environnement et de la Maitrise de l'Energie (ADEME) uses the Profitability Index Method to help define a wind energy tariff system for wind power plants under 12 MW. This paper presents some figures of the related over-cost incurred with the new tariff system which makes it possible for energy developers in France to develop huge wind potential at a pace equal to other countries with fixed premium prices. The over-cost of the new tariff system is not too high, plus it could be passed equally over all consumers of electricity. The tariff system will help France comply with its national, European and international commitments regarding climate change and with the future European directive on electricity generated from renewable energy sources. 8 refs., 1 tab., 4 figs

  9. [Proposal of a costing method for the provision of sterilization in a public hospital].

    Science.gov (United States)

    Bauler, S; Combe, C; Piallat, M; Laurencin, C; Hida, H

    2011-07-01

    To refine the billing to institutions whose operations of sterilization are outsourced, a sterilization cost approach was developed. The aim of the study is to determine the value of a sterilization unit (one point "S") evolving according to investments, quantities processed, types of instrumentation or packaging. The time of preparation has been selected from all sub-processes of sterilization to determine the value of one point S. The time of preparation of sterilized large and small containers and pouches were raised. The reference time corresponds to one bag (equal to one point S). Simultaneously, the annual operating cost of sterilization was defined and divided into several areas of expenditure: employees, equipments and building depreciation, supplies, and maintenance. A total of 136 crossing times of containers were measured. Time to prepare a pouch has been estimated at one minute (one S). A small container represents four S and a large container represents 10S. By dividing the operating cost of sterilization by the total number of points of sterilization over a given period, the cost of one S can be determined. This method differs from traditional costing method in sterilizing services, considering each item of expenditure. This point S will be the base for billing of subcontracts to other institutions. Copyright © 2011 Elsevier Masson SAS. All rights reserved.

  10. Board Game in Physics Classes—a Proposal for a New Method of Student Assessment

    Science.gov (United States)

    Dziob, Daniel

    2018-03-01

    The aim of this study was to examine the impact of assessing students' achievements in a physics course in the form of a group board game. Research was conducted in two groups of 131 high school students in Poland. In each school, the research sample was divided into experimental and control groups. Each group was taught by the same teacher and participated in the same courses and tests before the game. Just after finishing the course on waves and vibrations (school 1) and optics (school 2), experimental groups took part in a group board game to assess their knowledge. One week after the game, the experimental and control groups (not involved in the game) took part in the post-tests. Students from the experimental groups performed better in the game than in the tests given before the game. As well their results in the post-tests were significantly higher statistically than students from the control groups. Simultaneously, student's opinions in the experimental groups about the board game as an assessment method were collected in an open-descriptive form and in a short questionnaire, and analyzed. Results showed that students experienced a positive attitude toward the assessment method, a reduction of test anxiety and an increase in their motivation for learning.

  11. [The strategic research areas of a University Hospital: proposal of a quali-quantitative method.

    Science.gov (United States)

    Iezzi, Elisa; Ardissino, Diego; Ferrari, Carlo; Vitale, Marco; Caminiti, Caterina

    2018-02-01

    This work aimed to objectively identify the main research areas at the University Hospital of Parma. To this end, a multidisciplinary working group, comprising clinicians, researchers, and hospital management, was formed to develop a shared quali-quantitative method. Easily retrievable performance indicators were selected from the literature (concerning bibliometric data and grant acquisition), and a scoring system developed to assign weights to each indicator. Subsequently, Research Team Leaders were identified from the hospital's "Research Plan", a document produced every three years which contains information on the main research themes carried out at each Department, involved staff and available resources, provided by health care professionals themselves. The selected performance indicators were measured for each Team Leader, and scores assigned, thus creating a ranking list. Through the analyses of the research themes of top Team Leaders, the Working Group identified the following five strategic research areas: (a) personalized treatment in oncology and hematology; (b) chronicization mechanisms in immunomediate diseases; (c) old and new risk factors for cardiovascular diseases; (d) nutritional disorders, metabolic and chronic-degenerative diseases; (e) molecular diagnostic and predictive markers. We have developed an objective method to identify a hospital's main research areas. Its application can guide resource allocation and can offer ways to value the work of professionals involved in research.

  12. Automating Construction of Machine Learning Models With Clinical Big Data: Proposal Rationale and Methods.

    Science.gov (United States)

    Luo, Gang; Stone, Bryan L; Johnson, Michael D; Tarczy-Hornoch, Peter; Wilcox, Adam B; Mooney, Sean D; Sheng, Xiaoming; Haug, Peter J; Nkoy, Flory L

    2017-08-29

    To improve health outcomes and cut health care costs, we often need to conduct prediction/classification using large clinical datasets (aka, clinical big data), for example, to identify high-risk patients for preventive interventions. Machine learning has been proposed as a key technology for doing this. Machine learning has won most data science competitions and could support many clinical activities, yet only 15% of hospitals use it for even limited purposes. Despite familiarity with data, health care researchers often lack machine learning expertise to directly use clinical big data, creating a hurdle in realizing value from their data. Health care researchers can work with data scientists with deep machine learning knowledge, but it takes time and effort for both parties to communicate effectively. Facing a shortage in the United States of data scientists and hiring competition from companies with deep pockets, health care systems have difficulty recruiting data scientists. Building and generalizing a machine learning model often requires hundreds to thousands of manual iterations by data scientists to select the following: (1) hyper-parameter values and complex algorithms that greatly affect model accuracy and (2) operators and periods for temporally aggregating clinical attributes (eg, whether a patient's weight kept rising in the past year). This process becomes infeasible with limited budgets. This study's goal is to enable health care researchers to directly use clinical big data, make machine learning feasible with limited budgets and data scientist resources, and realize value from data. This study will allow us to achieve the following: (1) finish developing the new software, Automated Machine Learning (Auto-ML), to automate model selection for machine learning with clinical big data and validate Auto-ML on seven benchmark modeling problems of clinical importance; (2) apply Auto-ML and novel methodology to two new modeling problems crucial for care

  13. An algorithm for full parametric solution of problems on the statics of orthotropic plates by the method of boundary states with perturbations

    Science.gov (United States)

    Penkov, V. B.; Ivanychev, D. A.; Novikova, O. S.; Levina, L. V.

    2018-03-01

    The article substantiates the possibility of building full parametric analytical solutions of mathematical physics problems in arbitrary regions by means of computer systems. The suggested effective means for such solutions is the method of boundary states with perturbations, which aptly incorporates all parameters of an orthotropic medium in a general solution. We performed check calculations of elastic fields of an anisotropic rectangular region (test and calculation problems) for a generalized plane stress state.

  14. EPICOR-II resin characterization and proposed methods for degradation analysis. Rev. 1

    International Nuclear Information System (INIS)

    Doyle, J.D.; McConnell, J.W. Jr.; Sanders, R.D. Sr.

    1984-06-01

    One goal of the EPICOR-II Research and Disposition Program is the examination of the EPICOR-II organic ion-exchange resins for physical and chemical degradation. This report summarizes preliminary information necessary for the evaluation of the resins for degradation. Degradation of the synthetic organic ion-exchange resins should be efficiently and accurately measurable by using the baseline data provided by the nonirradiated resin characterization. The degradation threshold is about 10 8 rads, approximately the same dose rate the resins will have received by the examination date. If degradation has not occurred at the first examination point, later examinations will detect resin degradation using the same analytical methods. The results from the characterization tests will yield practical and useful data on the actual effects of radiation on commercial synthetic organic ion-exchange resins. 10 references, 12 figures

  15. Resolution analysis in full waveform inversion

    NARCIS (Netherlands)

    Fichtner, A.; Trampert, J.

    2011-01-01

    We propose a new method for the quantitative resolution analysis in full seismic waveform inversion that overcomes the limitations of classical synthetic inversions while being computationally more efficient and applicable to any misfit measure. The method rests on (1) the local quadratic

  16. Imaging disturbance zones ahead of a tunnel by elastic full-waveform inversion: Adjoint gradient based inversion vs. parameter space reduction using a level-set method

    Directory of Open Access Journals (Sweden)

    Andre Lamert

    2018-03-01

    Full Text Available We present and compare two flexible and effective methodologies to predict disturbance zones ahead of underground tunnels by using elastic full-waveform inversion. One methodology uses a linearized, iterative approach based on misfit gradients computed with the adjoint method while the other uses iterative, gradient-free unscented Kalman filtering in conjunction with a level-set representation. Whereas the former does not involve a priori assumptions on the distribution of elastic properties ahead of the tunnel, the latter introduces a massive reduction in the number of explicit model parameters to be inverted for by focusing on the geometric form of potential disturbances and their average elastic properties. Both imaging methodologies are validated through successful reconstructions of simple disturbances. As an application, we consider an elastic multiple disturbance scenario. By using identical synthetic time-domain seismograms as test data, we obtain satisfactory, albeit different, reconstruction results from the two inversion methodologies. The computational costs of both approaches are of the same order of magnitude, with the gradient-based approach showing a slight advantage. The model parameter space reduction approach compensates for this by additionally providing a posteriori estimates of model parameter uncertainty. Keywords: Tunnel seismics, Full waveform inversion, Seismic waves, Level-set method, Adjoint method, Kalman filter

  17. Proposal for element size and time increment selection guideline by 3-D finite element method for elastic waves propagation analysis

    International Nuclear Information System (INIS)

    Ishida, Hitoshi; Meshii, Toshiyuki

    2008-01-01

    This paper proposes a guideline for selection of element size and time increment by 3-D finite element method, which is applied to elastic wave propagation analysis for a long distance of a large structure. An element size and a time increment are determined by quantitative evaluation of strain, which must be 0 on the analysis model with a uniform motion, caused by spatial and time discretization. (author)

  18. PROPOSED SIMPLE METHOD FOR ELECTROCARDIOGRAM RECORDING IN FREE-RANGING ASIAN ELEPHANTS (ELEPHAS MAXIMUS).

    Science.gov (United States)

    Chai, Norin; Pouchelon, Jean Louis; Bouvard, Jonathan; Sillero, Leonor Camacho; Huynh, Minh; Segalini, Vincent; Point, Lisa; Croce, Veronica; Rigaux, Goulven; Highwood, Jack; Chetboul, Valérie

    2016-03-01

    Electrocardiography represents a relevant diagnostic tool for detecting cardiac disease in animals. Elephants can present various congenital and acquired cardiovascular diseases. However, few electrophysiologic studies have been reported in captive elephants, mainly due to challenging technical difficulties in obtaining good-quality electrocardiogram (ECG) tracings, and no data are currently available for free-ranging Asian elephants (Elephas maximus). The purpose of this pilot prospective study was to evaluate the feasibility of using a simple method for recording ECG tracings in wild, apparently healthy, unsedated Asian elephants (n = 7) in the standing position. Successful six-lead recordings (I, II, III, aVR, aVL, and aVF) were obtained, with the aVL lead providing the best-quality tracings in most animals. Variables measured in the aVL lead included heart rate, amplitudes and duration of the P waves, QRS complexes, T and U waves, and duration of the PR, QT, and QU intervals. A negative deflection following positive P waves, representative of an atrial repolarization wave (Ta wave), was observed for five out of the seven elephants.

  19. A proposed method to detect kinematic differences between and within individuals.

    Science.gov (United States)

    Frost, David M; Beach, Tyson A C; McGill, Stuart M; Callaghan, Jack P

    2015-06-01

    The primary objective was to examine the utility of a novel method of detecting "actual" kinematic changes using the within-subject variation. Twenty firefighters were assigned to one of two groups (lifting or firefighting). Participants performed 25 repetitions of two lifting or firefighting tasks, in three sessions. The magnitude and within-subject variation of several discrete kinematic measures were computed. Sequential averages of each variable were used to derive a cubic, quadratic and linear regression equation. The efficacy of each equation was examined by contrasting participants' sequential means to their 25-trial mean±1SD and 2SD. The magnitude and within-subject variation of each dependent measure was repeatable for all tasks; however, each participant did not exhibit the same movement patterns as the group. The number of instances across all variables, tasks and testing sessions whereby the 25-trial mean±1SD was contained within the boundaries established by the regression equations increased as the aggregate scores included more trials. Each equation achieved success in at least 88% of all instances when three trials were included in the sequential mean (95% with five trials). The within-subject variation may offer a means to examine participant-specific changes without having to collect a large number of trials. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Proposal of inspection method of radiation protection applied to nuclear medicine establishments

    International Nuclear Information System (INIS)

    Mendes, Leopoldino da Cruz Gouveia

    2003-01-01

    The principal objective of this paper is to implement a method of an impartial and efficient inspection, due to a correct and secure dose of ionizing radiation in the field of Nuclear Medicine. The Radiological Protection Model was tested in 113 Nuclear Medicine Services all over the country, according to a biannual analysis frequency (1996, 1998, 2000 and 2002). The data sheet comprised general information about the structure of the NMS and a technical approach. In the analytical process, a methodology of inputting different importance levels to each of the 82 features was adopted, based on the risk factors stated in the CNEN NE's and in the IAEA recommendations, as well. From this point of view, as a feature does not fit one of the rules above, it will correspond to a radioprotection fault and be imparted a grade. The sum of those grades, classified the NMS in one of the three different ranges, as follows: - operating without restriction - 100 points and below- operating with restriction - between 100 and 300 points - temporary shutdown - above and equal to 300 points. The allowance of the second group to carry on operating should be attached to a defined and restricted period of time (six to twelve months), supposed large enough to the NMS solving the problems being new evaluation proceeded then. The NMS's classified in the third group are supposed to go back into operation only when fit all the pending radioprotection requirements. Until the next regular evaluation, meanwhile a multiplication factor 2 n was applied to the recalcitrant NMS s where n is the number of unwilling occurrences. The previous establishment of those items of radioprotection, with its respective grade, excluded subjective and personal values in the judgement and technical evaluation of the institutions. (author)

  1. Volume-monitored chest CT: a simplified method for obtaining motion-free images near full inspiratory and end expiratory lung volumes

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, Kathryn S. [The Ohio State University College of Medicine, Columbus, OH (United States); Long, Frederick R. [Nationwide Children' s Hospital, The Children' s Radiological Institute, Columbus, OH (United States); Flucke, Robert L. [Nationwide Children' s Hospital, Department of Pulmonary Medicine, Columbus, OH (United States); Castile, Robert G. [The Research Institute at Nationwide Children' s Hospital, Center for Perinatal Research, Columbus, OH (United States)

    2010-10-15

    Lung inflation and respiratory motion during chest CT affect diagnostic accuracy and reproducibility. To describe a simple volume-monitored (VM) method for performing reproducible, motion-free full inspiratory and end expiratory chest CT examinations in children. Fifty-two children with cystic fibrosis (mean age 8.8 {+-} 2.2 years) underwent pulmonary function tests and inspiratory and expiratory VM-CT scans (1.25-mm slices, 80-120 kVp, 16-40 mAs) according to an IRB-approved protocol. The VM-CT technique utilizes instruction from a respiratory therapist, a portable spirometer and real-time documentation of lung volume on a computer. CT image quality was evaluated for achievement of targeted lung-volume levels and for respiratory motion. Children achieved 95% of vital capacity during full inspiratory imaging. For end expiratory scans, 92% were at or below the child's end expiratory level. Two expiratory exams were judged to be at suboptimal volumes. Two inspiratory (4%) and three expiratory (6%) exams showed respiratory motion. Overall, 94% of scans were performed at optimal volumes without respiratory motion. The VM-CT technique is a simple, feasible method in children as young as 4 years to achieve reproducible high-quality full inspiratory and end expiratory lung CT images. (orig.)

  2. Sensitivity analysis of a complex, proposed geologic waste disposal system using the Fourier Amplitude Sensitivity Test method

    International Nuclear Information System (INIS)

    Lu Yichi; Mohanty, Sitakanta

    2001-01-01

    The Fourier Amplitude Sensitivity Test (FAST) method has been used to perform a sensitivity analysis of a computer model developed for conducting total system performance assessment of the proposed high-level nuclear waste repository at Yucca Mountain, Nevada, USA. The computer model has a large number of random input parameters with assigned probability density functions, which may or may not be uniform, for representing data uncertainty. The FAST method, which was previously applied to models with parameters represented by the uniform probability distribution function only, has been modified to be applied to models with nonuniform probability distribution functions. Using an example problem with a small input parameter set, several aspects of the FAST method, such as the effects of integer frequency sets and random phase shifts in the functional transformations, and the number of discrete sampling points (equivalent to the number of model executions) on the ranking of the input parameters have been investigated. Because the number of input parameters of the computer model under investigation is too large to be handled by the FAST method, less important input parameters were first screened out using the Morris method. The FAST method was then used to rank the remaining parameters. The validity of the parameter ranking by the FAST method was verified using the conditional complementary cumulative distribution function (CCDF) of the output. The CCDF results revealed that the introduction of random phase shifts into the functional transformations, proposed by previous investigators to disrupt the repetitiveness of search curves, does not necessarily improve the sensitivity analysis results because it destroys the orthogonality of the trigonometric functions, which is required for Fourier analysis

  3. Full coverage of perovskite layer onto ZnO nanorods via a modified sequential two-step deposition method for efficiency enhancement in perovskite solar cells

    Science.gov (United States)

    Ruankham, Pipat; Wongratanaphisan, Duangmanee; Gardchareon, Atcharawon; Phadungdhitidhada, Surachet; Choopun, Supab; Sagawa, Takashi

    2017-07-01

    Full coverage of perovskite layer onto ZnO nanorod substrates with less pinholes is crucial for achieving high-efficiency perovskite solar cells. In this work, a two-step sequential deposition method is modified to achieve an appropriate property of perovskite (MAPbI3) film. Surface treatment of perovskite layer and its precursor have been systematically performed and their morphologies have been investigated. By pre-wetting of lead iodide (PbI2) and letting it dry before reacting with methylammonium iodide (MAI) provide better coverage of perovskite film onto ZnO nanorod substrate than one without any treatment. An additional MAI deposition followed with toluene drop-casting technique on the perovskite film is also found to increase the coverage and enhance the transformation of PbI2 to MAPbI3. These lead to longer charge carrier lifetime, resulting in an enhanced power conversion efficiency (PCE) from 1.21% to 3.05%. The modified method could been applied to a complex ZnO nanorods/TiO2 nanoparticles substrate. The enhancement in PCE to 3.41% is observed. These imply that our introduced method provides a simple way to obtain the full coverage and better transformation to MAPbI3 phase for enhancement in performances of perovskite solar cells.

  4. Morphision: A method for subjective evaluation of metamorphopsia in patients with unilateral macular pathology (i.e., full thickness macular hole and epiretinal membrane

    Directory of Open Access Journals (Sweden)

    Marta Ugarte

    2013-01-01

    Full Text Available Background: Lack of clinical tests to quantify spatial components of distortion in patients with full thickness macular holes (FTMH and epiretinal membranes (ERM. Aim: To develop a test for subjective evaluation of visual distortion in the central visual field around fixation in patients with unilateral FTMH or ERM. Settings and Design: Prospective case-control study carried out at tertiary referral center. Materials and Methods: Twenty-five patients with unilateral macular disease (13 macular epiretinal membranes, 12 full-thickness macular holes, and nine controls (without ocular pathology underwent ophthalmological examination with logMAR ETDRS visual acuity, near vision and contrast sensitivity assessed. Macular optical coherence tomography and metamorphopsia assessment using Morphision test was also carried out. This test consists of a set of modified Amsler charts for detection, identification, and subjective quantification of visual distortion in the central visual field around fixation. Morphision test content and construct validity, and reliability (test-retest method were evaluated. Sixteen patients completed an unstructured survey on test performance and preference. Results: Every patient with unilateral FTMH or ERM identified a particular chart using Morphision test (content validity. None of the normal subjects without symptoms of metamorphopsia identified any distortion (construct validity. Test-retest showed a 100% consistency for frequency and 67% for amplitude. The mean amplitude difference between measurements was 0.02 degrees (SD = 0.038. The coefficient of repeatability was 0.075. There was a correlation between Morphision amplitude score and visual acuity and contrast sensitivity, individually. Conclusions: Morphision test allowed detection and subjective quantification of metamorphopsia in the clinical setting in our patients with unilateral macular epiretinal membranes and full thickness macular holes.

  5. Methods for Quantifying the Uncertainties of LSIT Test Parameters, Test Results, and Full-Scale Mixing Performance Using Models Developed from Scaled Test Data

    International Nuclear Information System (INIS)

    Piepel, Gregory F.; Cooley, Scott K.; Kuhn, William L.; Rector, David R.; Heredia-Langner, Alejandro

    2015-01-01

    This report discusses the statistical methods for quantifying uncertainties in 1) test responses and other parameters in the Large Scale Integrated Testing (LSIT), and 2) estimates of coefficients and predictions of mixing performance from models that relate test responses to test parameters. Testing at a larger scale has been committed to by Bechtel National, Inc. and the U.S. Department of Energy (DOE) to ''address uncertainties and increase confidence in the projected, full-scale mixing performance and operations'' in the Waste Treatment and Immobilization Plant (WTP).

  6. Methods for Quantifying the Uncertainties of LSIT Test Parameters, Test Results, and Full-Scale Mixing Performance Using Models Developed from Scaled Test Data

    Energy Technology Data Exchange (ETDEWEB)

    Piepel, Gregory F. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Cooley, Scott K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kuhn, William L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rector, David R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Heredia-Langner, Alejandro [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-05-01

    This report discusses the statistical methods for quantifying uncertainties in 1) test responses and other parameters in the Large Scale Integrated Testing (LSIT), and 2) estimates of coefficients and predictions of mixing performance from models that relate test responses to test parameters. Testing at a larger scale has been committed to by Bechtel National, Inc. and the U.S. Department of Energy (DOE) to “address uncertainties and increase confidence in the projected, full-scale mixing performance and operations” in the Waste Treatment and Immobilization Plant (WTP).

  7. Isolation of full-length putative rat lysophospholipase cDNA using improved methods for mRNA isolation and cDNA cloning

    International Nuclear Information System (INIS)

    Han, J.H.; Stratowa, C.; Rutter, W.J.

    1987-01-01

    The authors have cloned a full-length putative rat pancreatic lysophospholipase cDNA by an improved mRNA isolation method and cDNA cloning strategy using [ 32 P]-labelled nucleotides. These new methods allow the construction of a cDNA library from the adult rat pancreas in which the majority of recombinant clones contained complete sequences for the corresponding mRNAs. A previously recognized but unidentified long and relatively rare cDNA clone containing the entire sequence from the cap site at the 5' end to the poly(A) tail at the 3' end of the mRNA was isolated by single-step screening of the library. The size, amino acid composition, and the activity of the protein expressed in heterologous cells strongly suggest this mRNA codes for lysophospholipase

  8. A fixed full-matrix method for determining ice sheet height change from satellite altimeter: an ENVISAT case study in East Antarctica with backscatter analysis

    Science.gov (United States)

    Yang, Yuande; Hwang, Cheinway; E, Dongchen

    2014-09-01

    A new method, called the fixed full-matrix method (FFM), is used to compute height changes at crossovers of satellite altimeter ground tracks. Using the ENVISAT data in East Antarctica, FFM results in crossovers of altimeter heights that are 1.9 and 79 times more than those from the fixed half method (FHM) and the one-row method (ORM). The mean standard error of height changes is about 14 cm from ORM, which is reduced to 7 cm by FHM and to 3 cm by FFM. Unlike FHM, FFM leads to uniform errors in the first-half and second-half height-change time series. FFM has the advantage in improving the accuracy of the change of height and backscattered power over ORM and FHM. Assisted by the ICESat-derived height changes, we determine the optimal threshold correlation coefficient (TCC) for a best correction for the backscatter effect on ENVISAT height changes. The TCC value of 0.92 yields an optimal result for FFM. With this value, FFM yields ENVISAT-derived height change rates in East Antarctica mostly falling between and 3 cm/year, and matching the ICESat result to 0.94 cm/year. The ENVISAT result will provide a constraint on the current mass balance result along the Chinese expedition route CHINARE.

  9. Full-Wave Analysis of the Shielding Effectiveness of Thin Graphene Sheets with the 3D Unidirectionally Collocated HIE-FDTD Method

    Directory of Open Access Journals (Sweden)

    Arne Van Londersele

    2017-01-01

    Full Text Available Graphene-based electrical components are inherently multiscale, which poses a real challenge for finite-difference time-domain (FDTD solvers due to the stringent time step upper bound. Here, a unidirectionally collocated hybrid implicit-explicit (UCHIE FDTD method is put forward that exploits the planar structure of graphene to increase the time step by implicitizing the critical dimension. The method replaces the traditional Yee discretization by a partially collocated scheme that allows a more accurate numerical description of the material boundaries. Moreover, the UCHIE-FDTD method preserves second-order accuracy even for nonuniform discretization in the direction of collocation. The auxiliary differential equation (ADE approach is used to implement the graphene sheet as a dispersive Drude medium. The finite grid is terminated by a uniaxial perfectly matched layer (UPML to permit open-space simulations. Special care is taken to elaborate on the efficient implementation of the implicit update equations. The UCHIE-FDTD method is validated by computing the shielding effectiveness of a typical graphene sheet.

  10. An assessment of the long term suitability of present and proposed methods for the management of uranium mill tailings

    International Nuclear Information System (INIS)

    1979-07-01

    Proposals for safe, long-term containment of conventional tailings include 1) storage under water, 2) storage in active, abandoned or specially created underground mines and, 3) storage in open pits, with subsequent flooding or covering with overburden. The underwater proposal can meet most of the requirements of long term containment; however, extensive study of existing tailings deposits in deep water locations will be needed. Underground mines cannot provide sufficient storage capacity, since the tailings bulk during mill operation can occupy twice the volume of the original ore. It is possible to reduce the hazard by reducing the radium and thorium content of the tailings. Proposals for such an undertaking include ore beneficiation with rejection of the relatively innocuous fraction, radium-thorium removal in the mill, and significant changes in both ore processing and treatment of tailings. It is concluded that surface-stored tailings are vulnerable over the long term to dispersion by leaching and water erosion, and that access to a tailings site cannot be prevented, while only a major climatic or seismic event could disturb tailings stored in suitable underwater or underground mine sites. The criteria for determining suitability for each method, however, will need to be identified, tested, and accepted through the normal process of modeling, pilot plant evaluation, monitoring and evaluation. (author)

  11. Proposal of a New Method for Neutron Dosimetry Based on Spectral Information Obtained by Application of Artificial Neural Networks

    International Nuclear Information System (INIS)

    Fehrenbacher, G.; Schuetz, R.; Hahn, K.; Sprunck, M.; Cordes, E.; Biersack, J.P.; Wahl, W.

    1999-01-01

    A new method for the monitoring of neutron radiation is proposed. It is based on the determination of spectral information on the neutron field in order to derive dose quantities like the ambient dose equivalent, the dose equivalent, or other dose quantities which depend on the neutron energy. The method uses a multi-element system consisting of converter type silicon detectors. The unfolding procedure is based on an artificial neural network (ANN). The response function of each element is determined by a computational model considering the neutron interaction with the dosemeter layers and the subsequent transport of produced ions. An example is given for a multi-element system. The ANN is trained by a given set of neutron spectra and then applied to count responses obtained in neutron fields. Four examples of spectra unfolded using the ANN are presented. (author)

  12. Validation of the Child Premorbid Intelligence Estimate method to predict premorbid Wechsler Intelligence Scale for Children-Fourth Edition Full Scale IQ among children with brain injury.

    Science.gov (United States)

    Schoenberg, Mike R; Lange, Rael T; Saklofske, Donald H; Suarez, Mariann; Brickell, Tracey A

    2008-12-01

    Determination of neuropsychological impairment involves contrasting obtained performances with a comparison standard, which is often an estimate of premorbid IQ. M. R. Schoenberg, R. T. Lange, T. A. Brickell, and D. H. Saklofske (2007) proposed the Child Premorbid Intelligence Estimate (CPIE) to predict premorbid Full Scale IQ (FSIQ) using the Wechsler Intelligence Scale for Children-4th Edition (WISC-IV; Wechsler, 2003). The CPIE includes 12 algorithms to predict FSIQ, 1 using demographic variables and 11 algorithms combining WISC-IV subtest raw scores with demographic variables. The CPIE was applied to a sample of children with acquired traumatic brain injury (TBI sample; n = 40) and a healthy demographically matched sample (n = 40). Paired-samples t tests found estimated premorbid FSIQ differed from obtained FSIQ when applied to the TBI sample (ps .02). The demographic only algorithm performed well at a group level, but estimates were restricted in range. Algorithms combining single subtest scores with demographics performed adequately. Results support the clinical application of the CPIE algorithms. However, limitations to estimating individual premorbid ability, including statistical and developmental factors, must be considered. (c) 2008 APA, all rights reserved.

  13. Proposal for an alignment method of the CLIC linear accelerator - From geodesic networks to the active pre-alignment

    International Nuclear Information System (INIS)

    Touze, T.

    2011-01-01

    The compact linear collider (CLIC) is the particle accelerator project proposed by the european organization for nuclear research (CERN) for high energy physics after the large hadron collider (LHC). Because of the nano-metric scale of the CLIC leptons beams, the emittance growth budget is very tight. It induces alignment tolerances on the positions of the CLIC components that have never been achieved before. The last step of the CLIC alignment will be done according to the beam itself. It falls within the competence of the physicists. However, in order to implement the beam-based feedback, a challenging pre-alignment is required: 10 μm at 3σ along a 200 m sliding window. For such a precision, the proposed solution must be compatible with a feedback between the measurement and repositioning systems. The CLIC pre-alignment will have to be active. This thesis does not demonstrate the feasibility of the CLIC active pre-alignment but shows the way to the last developments that have to be done for that purpose. A method is proposed. Based on the management of the Helmert transformations between Euclidean coordinate systems, from the geodetic networks to the metrological measurements, this method is likely to solve the CLIC pre-alignment problem. Large scale facilities have been built and Monte-Carlo simulations have been made in order to validate the mathematical modeling of the measurement systems and of the alignment references. When this is done, it will be possible to extrapolate the modeling to the entire CLIC length. It will be the last step towards the demonstration of the CLIC pre-alignment feasibility. (author)

  14. Effects of Conjugate Gradient Methods and Step-Length Formulas on the Multiscale Full Waveform Inversion in Time Domain: Numerical Experiments

    Science.gov (United States)

    Liu, Youshan; Teng, Jiwen; Xu, Tao; Badal, José; Liu, Qinya; Zhou, Bing

    2017-05-01

    We carry out full waveform inversion (FWI) in time domain based on an alternative frequency-band selection strategy that allows us to implement the method with success. This strategy aims at decomposing the seismic data within partially overlapped frequency intervals by carrying out a concatenated treatment of the wavelet to largely avoid redundant frequency information to adapt to wavelength or wavenumber coverage. A pertinent numerical test proves the effectiveness of this strategy. Based on this strategy, we comparatively analyze the effects of update parameters for the nonlinear conjugate gradient (CG) method and step-length formulas on the multiscale FWI through several numerical tests. The investigations of up to eight versions of the nonlinear CG method with and without Gaussian white noise make clear that the HS (Hestenes and Stiefel in J Res Natl Bur Stand Sect 5:409-436, 1952), CD (Fletcher in Practical methods of optimization vol. 1: unconstrained optimization, Wiley, New York, 1987), and PRP (Polak and Ribière in Revue Francaise Informat Recherche Opertionelle, 3e Année 16:35-43, 1969; Polyak in USSR Comput Math Math Phys 9:94-112, 1969) versions are more efficient among the eight versions, while the DY (Dai and Yuan in SIAM J Optim 10:177-182, 1999) version always yields inaccurate result, because it overestimates the deeper parts of the model. The application of FWI algorithms using distinct step-length formulas, such as the direct method ( Direct), the parabolic search method ( Search), and the two-point quadratic interpolation method ( Interp), proves that the Interp is more efficient for noise-free data, while the Direct is more efficient for Gaussian white noise data. In contrast, the Search is less efficient because of its slow convergence. In general, the three step-length formulas are robust or partly insensitive to Gaussian white noise and the complexity of the model. When the initial velocity model deviates far from the real model or the

  15. Myocardial infarct sizing by late gadolinium-enhanced MRI: Comparison of manual, full-width at half-maximum, and n-standard deviation methods.

    Science.gov (United States)

    Zhang, Lin; Huttin, Olivier; Marie, Pierre-Yves; Felblinger, Jacques; Beaumont, Marine; Chillou, Christian DE; Girerd, Nicolas; Mandry, Damien

    2016-11-01

    To compare three widely used methods for myocardial infarct (MI) sizing on late gadolinium-enhanced (LGE) magnetic resonance (MR) images: manual delineation and two semiautomated techniques (full-width at half-maximum [FWHM] and n-standard deviation [SD]). 3T phase-sensitive inversion-recovery (PSIR) LGE images of 114 patients after an acute MI (2-4 days and 6 months) were analyzed by two independent observers to determine both total and core infarct sizes (TIS/CIS). Manual delineation served as the reference for determination of optimal thresholds for semiautomated methods after thresholding at multiple values. Reproducibility and accuracy were expressed as overall bias ± 95% limits of agreement. Mean infarct sizes by manual methods were 39.0%/24.4% for the acute MI group (TIS/CIS) and 29.7%/17.3% for the chronic MI group. The optimal thresholds (ie, providing the closest mean value to the manual method) were FWHM30% and 3SD for the TIS measurement and FWHM45% and 6SD for the CIS measurement (paired t-test; all P > 0.05). The best reproducibility was obtained using FWHM. For TIS measurement in the acute MI group, intra-/interobserver agreements, from Bland-Altman analysis, with FWHM30%, 3SD, and manual were -0.02 ± 7.74%/-0.74 ± 5.52%, 0.31 ± 9.78%/2.96 ± 16.62% and -2.12 ± 8.86%/0.18 ± 16.12, respectively; in the chronic MI group, the corresponding values were 0.23 ± 3.5%/-2.28 ± 15.06, -0.29 ± 10.46%/3.12 ± 13.06% and 1.68 ± 6.52%/-2.88 ± 9.62%, respectively. A similar trend for reproducibility was obtained for CIS measurement. However, semiautomated methods produced inconsistent results (variabilities of 24-46%) compared to manual delineation. The FWHM technique was the most reproducible method for infarct sizing both in acute and chronic MI. However, both FWHM and n-SD methods showed limited accuracy compared to manual delineation. J. Magn. Reson. Imaging 2016;44:1206-1217. © 2016 International Society for Magnetic Resonance in Medicine.

  16. Precision of glucose measurements in control sera by isotope dilution/mass spectrometry: proposed definitive method compared with a reference method

    International Nuclear Information System (INIS)

    Pelletier, O.; Arratoon, C.

    1987-01-01

    This improved isotope-dilution gas chromatographic/mass spectrometric (GC/MS) method, in which [ 13 C]glucose is the internal standard, meets the requirements of a Definitive Method. In a first study with five reconstituted lyophilized sera, a nested analysis of variance of GC/MS values indicated considerable among-vial variation. The CV for 32 measurements per serum ranged from 0.5 to 0.9%. However, concentration and uncertainty values (mmol/L per gram of serum) assigned to one serum by the NBS Definitive Method (7.56 +/- 0.28) were practically identical to those obtained with the proposed method (7.57 +/- 0.20). In the second study, we used twice more [ 13 C]glucose diluent to assay four serum pools and two lyophilized sera. The CV ranged from 0.26 to 0.5% for the serum pools and from 0.28 to 0.59% for the lyophilized sera. In comparison, results by the hexokinase/glucose-6-phosphate dehydrogenase reference method agreed within acceptable limits with those by the Definitive Method but tended to be slightly higher (up to 3%) for lyophilized serum samples or slightly lower (up to 2.5%) for serum pools

  17. Extension of a dynamic headspace multi-volatile method to milliliter injection volumes with full sample evaporation: Application to green tea.

    Science.gov (United States)

    Ochiai, Nobuo; Sasamoto, Kikuo; Tsunokawa, Jun; Hoffmann, Andreas; Okanoya, Kazunori; MacNamara, Kevin

    2015-11-20

    An extension of multi-volatile method (MVM) technology using the combination of a standard dynamic headspace (DHS) configuration, and a modified DHS configuration incorporating an additional vacuum module, was developed for milliliter injection volume of aqueous sample with full sample evaporation. A prior step involved investigation of water management by weighing of the water residue in the adsorbent trap. The extended MVM for 1 mL aqueous sample consists of five different DHS method parameter sets including choice of the replaceable adsorbent trap. An initial two DHS sampling sets at 25°C with the standard DHS configuration using a carbon-based adsorbent trap target very volatile solutes with high vapor pressure (>10 kPa) and volatile solutes with moderate vapor pressure (1-10 kPa). Subsequent three DHS sampling sets at 80°C with the modified DHS configuration using a Tenax TA trap target solutes with low vapor pressure (88%) for 17 test aroma compounds and moderate recoveries (44-71%) for 4 test compounds. The method showed good linearity (r(2)>0.9913) and high sensitivity (limit of detection: 0.1-0.5 ng mL(-1)) even with MS scan mode. The improved sensitivity of the method was demonstrated with analysis of a wide variety of aroma compounds in brewed green tea. Compared to the original 100 μL MVM procedure, this extension to 1 mL MVM allowed detection of nearly twice the number of aroma compounds, including 18 potent aroma compounds from top-note to base-note (e.g. 2,3-butanedione, coumarin, furaneol, guaiacol, cis-3-hexenol, linalool, maltol, methional, 3-methyl butanal, 2,3,5-trimethyl pyrazine, and vanillin). Sensitivity for 23 compounds improved by a factor of 3.4-15 under 1 mL MVM conditions. Copyright © 2015 Elsevier B.V. All rights reserved.

  18. Verbal Auditory Cueing of Improvisational Dance: A Proposed Method for Training Agency in Parkinson’s Disease

    Science.gov (United States)

    Batson, Glenna; Hugenschmidt, Christina E.; Soriano, Christina T.

    2016-01-01

    Dance is a non-pharmacological intervention that helps maintain functional independence and quality of life in people with Parkinson’s disease (PPD). Results from controlled studies on group-delivered dance for people with mild-to-moderate stage Parkinson’s have shown statistically and clinically significant improvements in gait, balance, and psychosocial factors. Tested interventions include non-partnered dance forms (ballet and modern dance) and partnered (tango). In all of these dance forms, specific movement patterns initially are learned through repetition and performed in time-to-music. Once the basic steps are mastered, students may be encouraged to improvise on the learned steps as they perform them in rhythm with the music. Here, we summarize a method of teaching improvisational dance that advances previous reported benefits of dance for people with Parkinson’s disease (PD). The method relies primarily on improvisational verbal auditory cueing with less emphasis on directed movement instruction. This method builds on the idea that daily living requires flexible, adaptive responses to real-life challenges. In PD, movement disorders not only limit mobility but also impair spontaneity of thought and action. Dance improvisation demands open and immediate interpretation of verbally delivered movement cues, potentially fostering the formation of spontaneous movement strategies. Here, we present an introduction to a proposed method, detailing its methodological specifics, and pointing to future directions. The viewpoint advances an embodied cognitive approach that has eco-validity in helping PPD meet the changing demands of daily living. PMID:26925029

  19. Proposal for evaluation methodology on impact resistant performance and construction method of tornado missile protection net structure

    International Nuclear Information System (INIS)

    Namba, Kosuke; Shirai, Koji

    2014-01-01

    In nuclear power plants, the necessity of the Tornado Missile Protection Structure is becoming a technical key issue. Utilization of the net structure seems to be one of the realistic counter measures from the point of the view of the mitigation wind and seismic loads. However, the methodology for the selection of the net suitable materials, the energy absorption design method and the construction method are not sufficiently established. In this report, three materials (high-strength metal mesh, super strong polyethylene fiber net and steel grating) were selected for the candidate material and the material screening tests, the energy absorption tests by free drop test using the heavy weight and the impact tests with the small diameter missile. As a result, high-strength metal mesh was selected as a suitable material for tornado missile protection net structure. Moreover, the construction method to obtain the good energy absorption performance of the material and the practical design method to estimate the energy absorption of the high-strength metal mesh under tornado missile impact load were proposed. (author)

  20. Proposed method for agglutinating antibody titer analysis and its use as indicator of acquired immunity in pacu, Piaractus mesopotamicus

    Directory of Open Access Journals (Sweden)

    JD Biller-Takahashi

    Full Text Available Antibody can be assessed by agglutinating antibody titer which is a quantitative measure of circulating antibodies in serum from fish previously immunized. The antibody evaluation has been performed with different fish species, and is considered a reliable method that can be applied to confirm several hypothesis regarding acquired immunity, even in conjunction with precise methods to describe immune mechanisms. In order to provide appropriate analytical methods for future studies on the specific immune system of native fish, the present study standardized on assay to measure the serum agglutinating antibody titer produced after immunization with inactivated A. hydrophila and levamisole administration in pacu. It was possible to determine the agglutinating antibodies titer in a satisfactorily way in pacu immunized with inactive A. hydrophila, and the highest titers were observed on fish fed with levamisole.

  1. Proposal of an Appropriate Decalcification Method of Bone Marrow Biopsy Specimens in the Era of Expanding Genetic Molecular Study

    Directory of Open Access Journals (Sweden)

    Sung-Eun Choi

    2015-05-01

    Full Text Available Background: The conventional method for decalcification of bone specimens uses hydrochloric acid (HCl and is notorious for damaging cellular RNA, DNA, and proteins, thus complicating molecular and immunohistochemical analyses. A method that can effectively decalcify while preserving genetic material is necessary. Methods: Pairs of bilateral bone marrow biopsies sampled from 53 patients were decalcified according to protocols of two comparison groups: EDTA versus HCl and RDO GOLD (RDO versus HCl. Pairs of right and left bone marrow biopsy samples harvested from 28 cases were allocated into the EDTA versus HCl comparison group, and 25 cases to the RDO versus HCl comparison group. The decalcification protocols were compared with regards to histomorphology, immunohistochemistry, and molecular analysis. For molecular analysis, we randomly selected 5 cases from the EDTA versus HCl and RDO versus HCl groups. Results: The decalcification time for appropriate histomorphologic analysis was the longest in the EDTA method and the shortest in the RDO method. EDTA was superior to RDO or HCl in DNA yield and integrity, assessed via DNA extraction, polymerase chain reaction, and silver in situ hybridization using DNA probes. The EDTA method maintained intact nuclear protein staining on immunohistochemistry, while the HCl method produced poor quality images. Staining after the RDO method had equivocal results. RNA in situ hybridization using kappa and lambda RNA probes measured RNA integrity; the EDTA and RDO method had the best quality, followed by HCl. Conclusions: The EDTA protocol would be the best in preserving genetic material. RDO may be an acceptable alternative when rapid decalcification is necessary.

  2. Developing an Agent-Based Simulation System for Post-Earthquake Operations in Uncertainty Conditions: A Proposed Method for Collaboration among Agents

    Directory of Open Access Journals (Sweden)

    Navid Hooshangi

    2018-01-01

    Full Text Available Agent-based modeling is a promising approach for developing simulation tools for natural hazards in different areas, such as during urban search and rescue (USAR operations. The present study aimed to develop a dynamic agent-based simulation model in post-earthquake USAR operations using geospatial information system and multi agent systems (GIS and MASs, respectively. We also propose an approach for dynamic task allocation and establishing collaboration among agents based on contract net protocol (CNP and interval-based Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS methods, which consider uncertainty in natural hazards information during agents’ decision-making. The decision-making weights were calculated by analytic hierarchy process (AHP. In order to implement the system, earthquake environment was simulated and the damage of the buildings and a number of injuries were calculated in Tehran’s District 3: 23%, 37%, 24% and 16% of buildings were in slight, moderate, extensive and completely vulnerable classes, respectively. The number of injured persons was calculated to be 17,238. Numerical results in 27 scenarios showed that the proposed method is more accurate than the CNP method in the terms of USAR operational time (at least 13% decrease and the number of human fatalities (at least 9% decrease. In interval uncertainty analysis of our proposed simulated system, the lower and upper bounds of uncertain responses are evaluated. The overall results showed that considering uncertainty in task allocation can be a highly advantageous in the disaster environment. Such systems can be used to manage and prepare for natural hazards.

  3. Extending the precision and efficiency of the all-electron full-potential linearized augmented plane-wave density-functional theory method

    International Nuclear Information System (INIS)

    Michalicek, Gregor

    2015-01-01

    Density functional theory (DFT) is the most widely-used first-principles theory for analyzing, describing and predicting the properties of solids based on the fundamental laws of quantum mechanics. The success of the theory is a consequence of powerful approximations to the unknown exchange and correlation energy of the interacting electrons and of sophisticated electronic structure methods that enable the computation of the density functional equations on a computer. A widely used electronic structure method is the full-potential linearized augmented plane-wave (FLAPW) method, that is considered to be one of the most precise methods of its kind and often referred to as a standard. Challenged by the demand of treating chemically and structurally increasingly more complex solids, in this thesis this method is revisited and extended along two different directions: (i) precision and (ii) efficiency. In the full-potential linearized augmented plane-wave method the space of a solid is partitioned into nearly touching spheres, centered at each atom, and the remaining interstitial region between the spheres. The Kohn-Sham orbitals, which are used to construct the electron density, the essential quantity in DFT, are expanded into a linearized augmented plane-wave basis, which consists of plane waves in the interstitial region and angular momentum dependent radial functions in the spheres. In this thesis it is shown that for certain types of materials, e.g., materials with very broad electron bands or large band gaps, or materials that allow the usage of large space-filling spheres, the variational freedom of the basis in the spheres has to be extended in order to represent the Kohn-Sham orbitals with high precision over a large energy spread. Two kinds of additional radial functions confined to the spheres, so-called local orbitals, are evaluated and found to successfully eliminate this error. A new efficient basis set is developed, named linearized augmented lattice

  4. MERCURY QUANTIFICATION IN SOILS USING THERMAL DESORPTION AND ATOMIC ABSORPTION SPECTROMETRY: PROPOSAL FOR AN ALTERNATIVE METHOD OF ANALYSIS

    Directory of Open Access Journals (Sweden)

    Liliane Catone Soares

    2015-08-01

    Full Text Available Despite the considerable environmental importance of mercury (Hg, given its high toxicity and ability to contaminate large areas via atmospheric deposition, little is known about its activity in soils, especially tropical soils, in comparison with other heavy metals. This lack of information about Hg arises because analytical methods for determination of Hg are more laborious and expensive compared to methods for other heavy metals. The situation is even more precarious regarding speciation of Hg in soils since sequential extraction methods are also inefficient for this metal. The aim of this paper is to present a technique of thermal desorption associated with atomic absorption spectrometry, TDAAS, as an efficient tool for quantitative determination of Hg in soils. The method consists of the release of Hg by heating, followed by its quantification by atomic absorption spectrometry. It was developed by constructing calibration curves in different soil samples based on increasing volumes of standard Hg2+ solutions. Performance, accuracy, precision, and quantification and detection limit parameters were evaluated. No matrix interference was detected. Certified reference samples and comparison with a Direct Mercury Analyzer, DMA (another highly recognized technique, were used in validation of the method, which proved to be accurate and precise.

  5. Mapping subsurface pathways for contaminant migration at a proposed low level waste disposal site using electromagnetic methods

    International Nuclear Information System (INIS)

    Pin, F.G.; Ketelle, R.H.

    1984-01-01

    Electromagnetic methods have been used to measure apparent terrain conductivity in the downstream portion of a watershed in which a waste disposal site is proposed. At that site, the pathways for waste migration in ground water are controlled by subsurface channels. The channels are identified using isocurves of measured apparent conductivity. Two upstream channel branches are found to merge into a single downstream channel which constitutes the main drainage path out of the watershed. The identification and mapping of the ground water pathways is an important contribution to the site characterization study and the pathways analysis. The direct applications of terrain conductivity mapping to the planning of the monitoring program, the hydrogeological testing, and the modeling study are demonstrated. 7 references, 4 figures

  6. Proposal of quality indicators for cardiac rehabilitation after acute coronary syndrome in Japan: a modified Delphi method and practice test.

    Science.gov (United States)

    Ohtera, Shosuke; Kanazawa, Natsuko; Ozasa, Neiko; Ueshima, Kenji; Nakayama, Takeo

    2017-01-27

    Cardiac rehabilitation is underused and its quality in practice is unclear. A quality indicator is a measurable element of clinical practice performance. This study aimed to propose a set of quality indicators for cardiac rehabilitation following an acute coronary event in the Japanese population and conduct a small-size practice test to confirm feasibility and applicability of the indicators in real-world clinical practice. This study used a modified Delphi technique (the RAND/UCLA appropriateness method), a consensus method which involves an evidence review, a face-to-face multidisciplinary panel meeting and repeated anonymous rating. Evidence to be reviewed included clinical practice guidelines available in English or Japanese and existing quality indicators. Performance of each indicator was assessed retrospectively using medical records at a university hospital in Japan. 10 professionals in cardiac rehabilitation for the consensus panel. In the literature review, 23 clinical practice guidelines and 16 existing indicators were identified to generate potential indicators. Through the consensus-building process, a total of 30 indicators were assessed and finally 13 indicators were accepted. The practice test (n=39) revealed that 74% of patients underwent cardiac rehabilitation. Median performance of process measures was 93% (IQR 46-100%). 'Communication with the doctor who referred the patient to cardiac rehabilitation' and 'continuous participation in cardiac rehabilitation' had low performance (32% and 38%, respectively). A modified Delphi technique identified a comprehensive set of quality indicators for cardiac rehabilitation. The single-site, small-size practice test confirmed that most of the proposed indicators were measurable in real-world clinical practice. However, some clinical processes which are not covered by national health insurance in Japan had low performance. Further studies will be needed to clarify and improve the quality of care in cardiac

  7. [The influence of the different polishing methods on the marginal sealing property of the computer aided design and computer aided manufacture zirconium dioxide full crown].

    Science.gov (United States)

    Zhou, Jianying; Deng, Jiupeng; Li, Jinyuan; Wang, Jide; Shen, Baolian

    2016-05-01

    To evaluate the influence of different polishing methods on marginal microleakage of zirconium dioxide full crown. Thirty extracted premolars were selected and randomly divided into three groups, A, B and C, with 10 in each group. Group A was prepared with MANI TF-13 bur completely without the treatment of shoulder. The shoulder of group B was polished with MANI TR13-EF bur after the preparation using MANI TF-13. The shoulder of group C was polished with the dental pneumatic ultrasonic hand-piece of KaVo SONICflex after the preparation using MANI TF-13 bur. Five specimens after preparation were selected in each group. Fifteen CAD/CAM zirconium dioxide full crowns have been made. The crowns were bonded using PULPDENT resin cement, and the root canals were sealed using nail polish, and apical foramen were closed using flow resin. The test-pieces have been immersed in a 3% solution of methylene blue for 24 h. The condition of shoulder marginal microleakage was observed using light stereomicroscopy and evaluated in classification index. The remaining specimens in each group were used for roughness test and scanning electron microscope(SEM) experiment. The marginal microleakage situations of specimens in three groups was analyzed by SPSS 17.0. The enamel surface of different polishing methods was observed using SEM. The specimens in group C demonstrated the least marginal microleakage, and those in group B showed an intermediate level of marginal microleakage, and those in group A characterized the most serious marginal microleakage (total, χ2=44.610, P<0.01; among the different groups, P<0.05). The roughness experiment showed that specimens in group C achieve the smoothest results ([0.27±0.03] μm). Preparation shoulder polished using the dental pneumatic ultrasonic hand-piece demonstrated the best result under the SEM among the three groups. The anti-microleakage effectiveness of dental pneumatic ultrasonic hand-piece in shoulder refinement is better than ordinary

  8. A Simplified Method for Three-Dimensional (3-D Ovarian Tissue Culture Yielding Oocytes Competent to Produce Full-Term Offspring in Mice.

    Directory of Open Access Journals (Sweden)

    Carolyn M Higuchi

    Full Text Available In vitro growth of follicles is a promising technology to generate large quantities of competent oocytes from immature follicles and could expand the potential of assisted reproductive technologies (ART. Isolated follicle culture is currently the primary method used to develop and mature follicles in vitro. However, this procedure typically requires complicated, time-consuming procedures, as well as destruction of the normal ovarian microenvironment. Here we describe a simplified 3-D ovarian culture system that can be used to mature multilayered secondary follicles into antral follicles, generating developmentally competent oocytes in vitro. Ovaries recovered from mice at 14 days of age were cut into 8 pieces and placed onto a thick Matrigel drop (3-D culture for 10 days of culture. As a control, ovarian pieces were cultured on a membrane filter without any Matrigel drop (Membrane culture. We also evaluated the effect of activin A treatment on follicle growth within the ovarian pieces with or without Matrigel support. Thus we tested four different culture conditions: C (Membrane/activin-, A (Membrane/activin+, M (Matrigel/activin-, and M+A (Matrigel/activin+. We found that the cultured follicles and oocytes steadily increased in size regardless of the culture condition used. However, antral cavity formation occurred only in the follicles grown in the 3-D culture system (M, M+A. Following ovarian tissue culture, full-grown GV oocytes were isolated from the larger follicles to evaluate their developmental competence by subjecting them to in vitro maturation (IVM and in vitro fertilization (IVF. Maturation and fertilization rates were higher using oocytes grown in 3-D culture (M, M+A than with those grown in membrane culture (C, A. In particular, activin A treatment further improved 3-D culture (M+A success. Following IVF, two-cell embryos were transferred to recipients to generate full-term offspring. In summary, this simple and easy 3-D ovarian

  9. International survey of methods used in health technology assessment (HTA: does practice meet the principles proposed for good research?

    Directory of Open Access Journals (Sweden)

    Stephens JM

    2012-08-01

    Full Text Available Jennifer M Stephens,1 Bonnie Handke,2 Jalpa A Doshi3 On behalf of the HTA Principles Working Group, part of the International Society for Pharmacoeconomics and Outcomes Research (ISPOR HTA Special Interest Group (SIG1Pharmerit International, Bethesda, MD, USA; 2Medtronic Neuromodulation, Minneapolis, MN, USA; 3Center for Evidence-Based Practice and Center for Health Incentives and Behavioral Economics, Perelman School of Medicine, University of Pennsylvania, Philadelphia, PA, USAObjective: To describe research methods used internationally in health technology assessment (HTA and health-care reimbursement policies; compare the survey findings on research methods and processes to published HTA principles; and discuss important issues/trends reported by HTA bodies related to current research methods and applications of the HTA process.Methods: Representatives from HTA bodies worldwide were recruited to complete an online survey consisting of 47 items within four topics: (1 organizational information and process, (2 primary HTA methodologies and importance of attributes, (3 HTA application and dissemination, and (4 quality of HTA, including key issues. Results were presented as a comparison of current HTA practices and research methods to published HTA principles.Results: The survey was completed by 30 respondents representing 16 countries in five major regions, Australia (n = 3, Canada (n = 2, Europe (n = 17, Latin America (n = 2, and the United States (n = 6. The most common methodologies used were systematic review, meta-analysis, and economic modeling. The most common attributes evaluated were effectiveness (more commonly than efficacy, cost-effectiveness, safety, and quality of life. The attributes assessed, relative importance of the attributes, and conformance with HTA principles varied by region/country. Key issues and trends facing HTA bodies included standardizing methods for economic evaluations and grading of evidence, lack of evidence

  10. Full-Wave Analysis of Field-to-Line Coupling Effects Using 1D FDTD Method under Exciting Source with Different Bandwidths

    Directory of Open Access Journals (Sweden)

    Qi Zhang

    2014-01-01

    Full Text Available With the aim to analyze field-to-line coupling effects based on energy spectrum, parallel finite-difference time-domain (FDTD method is applied to calculate the induced voltage on overhead lines under high-power electromagnetic (HPEM environment. Firstly, the energy distribution laws of HEMP (IEC 61000-2-9, HEMP (Bell Laboratory, HEMP (Paulino et al., 2010, and LEMP (IEC61000-4-5 are given. Due to the air-earth stratified medium, both the absorbing boundary and the connecting boundary applied to scattering by finite-length objects are separately set in aerial and underground parts. Moreover, the influence of line length on induced voltage is analyzed and discussed. The results indicate that the half-peak width is wider with the increase of the line length. But the steepness of induced voltage on the overhead line is invariable. There is no further increase in the peak of induced voltage especially when the line length increases to be equivalent to the wavelength of the frequency bands with the maximum energy.

  11. A Proposal of a Method to Measure and Evaluate the Effect to Apply External Support Measures for Owners by Construction Management Method, etc

    Science.gov (United States)

    Tada, Hiroshi; Miyatake, Ichiro; Mouri, Junji; Ajiki, Norihiko; Fueta, Toshiharu

    In Japan, various approaches have been taken to ensure the quality of public works or to support the procurement regime of the governmental agencies, as a means to utilize external resources, which include the procurement support service or the construction management (CM) method. Although discussions on these measures to utilize external resources (hereinafter referred to as external support measure) have been going on, as well as the follow-up surveys showing the positive effects of such measures have been conducted, the surveys only deal with the matters concerning the overall effects of the external support measure on the whole, meaning that the effect of each item of the tasks have not been addressed, and that the extent it dealt with the expectations of the client is unknown. However, the effective use of the external support measure in future cannot be achieved without knowing what was the purpose to introduce the external support measure, and what effect was expected on each task item, and what extent the expectation fulfilled. Furthermore, it is important to clarify not only the effect as compared to the client's expectation (performance), but also the public benefit of this measure (value improvement). From this point of view, there is not an established method to figure out the effect of the client's measure to utilize external resources. In view of this background, this study takes the CM method as an example of the external support measure, and proposes a method to measure and evaluate the effect by each task item, and suggests the future issues and possible responses, in the aim of contributing the promotion, improvement, and proper implementation of the external support measures in future.

  12. Oriented Polar Molecules in a Solid Inert-Gas Matrix: A Proposed Method for Measuring the Electric Dipole Moment of the Electron

    Directory of Open Access Journals (Sweden)

    A. C. Vutha

    2018-01-01

    Full Text Available We propose a very sensitive method for measuring the electric dipole moment of the electron using polar molecules embedded in a cryogenic solid matrix of inert-gas atoms. The polar molecules can be oriented in the z ^ -direction by an applied electric field, as has recently been demonstrated by Park et al. The trapped molecules are prepared into a state that has its electron spin perpendicular to z ^ , and a magnetic field along z ^ causes precession of this spin. An electron electric dipole moment d e would affect this precession due to the up to 100 GV/cm effective electric field produced by the polar molecule. The large number of polar molecules that can be embedded in a matrix, along with the expected long coherence times for the precession, allows for the possibility of measuring d e to an accuracy that surpasses current measurements by many orders of magnitude. Because the matrix can inhibit molecular rotations and lock the orientation of the polar molecules, it may not be necessary to have an electric field present during the precession. The proposed technique can be applied using a variety of polar molecules and inert gases, which, along with other experimental variables, should allow for careful study of systematic uncertainties in the measurement.

  13. Proposals for the Operationalisation of the Discourse Theory of Laclau and Mouffe Using a Triangulation of Lexicometrical and Interpretative Methods

    Directory of Open Access Journals (Sweden)

    Georg Glasze

    2007-05-01

    Full Text Available The discourse theory of Ernesto LACLAU and Chantal MOUFFE brings together three elements: the FOUCAULTian notion of discourse, the (post- MARXist notion of hegemony, and the poststructuralist writings of Jacques DERRIDA and Roland BARTHES. Discourses are regarded as temporary fixations of differential relations. Meaning, i.e. any social "objectivity", is conceptualised as an effect of such a fixation. The discussion on an appropriate operationalisation of such a discourse theory is just beginning. In this paper, it is argued that a triangulation of two linguistic methods is appropriate to reveal temporary fixations: by means of corpus-driven lexicometric procedures as well as by the analysis of narrative patterns, the regularities of the linkage of elements can be analysed (for example, in diachronic comparisons. The example of a geographic research project shows how, in so doing, the historically contingent constitution of an international community and "world region" can be analysed. URN: urn:nbn:de:0114-fqs0702143

  14. A Proposal of Estimation Methodology to Improve Calculation Efficiency of Sampling-based Method in Nuclear Data Sensitivity and Uncertainty Analysis

    International Nuclear Information System (INIS)

    Song, Myung Sub; Kim, Song Hyun; Kim, Jong Kyung; Noh, Jae Man

    2014-01-01

    The uncertainty with the sampling-based method is evaluated by repeating transport calculations with a number of cross section data sampled from the covariance uncertainty data. In the transport calculation with the sampling-based method, the transport equation is not modified; therefore, all uncertainties of the responses such as k eff , reaction rates, flux and power distribution can be directly obtained all at one time without code modification. However, a major drawback with the sampling-based method is that it requires expensive computational load for statistically reliable results (inside confidence level 0.95) in the uncertainty analysis. The purpose of this study is to develop a method for improving the computational efficiency and obtaining highly reliable uncertainty result in using the sampling-based method with Monte Carlo simulation. The proposed method is a method to reduce the convergence time of the response uncertainty by using the multiple sets of sampled group cross sections in a single Monte Carlo simulation. The proposed method was verified by estimating GODIVA benchmark problem and the results were compared with that of conventional sampling-based method. In this study, sampling-based method based on central limit theorem is proposed to improve calculation efficiency by reducing the number of repetitive Monte Carlo transport calculation required to obtain reliable uncertainty analysis results. Each set of sampled group cross sections is assigned to each active cycle group in a single Monte Carlo simulation. The criticality uncertainty for the GODIVA problem is evaluated by the proposed and previous method. The results show that the proposed sampling-based method can efficiently decrease the number of Monte Carlo simulation required for evaluate uncertainty of k eff . It is expected that the proposed method will improve computational efficiency of uncertainty analysis with sampling-based method

  15. Feasibility study and technical proposal for the use of microseismic methods in the long-term observation of bedrock stability

    International Nuclear Information System (INIS)

    Saari, J.

    1995-04-01

    Recent geodetic and seismological studies have paid attention to the slow deformation occurring in the Fennoscandian Shield. On the basis of these studies, together with in-situ stress measurements, the idea has been put forth that horizontal movement can be even greater than vertical movement. Local seismotectonics has importance in relation to the predictions of the long-term stability of the bedrock at the final disposal site. Potential direct and - what in Finland is more likely - indirect effects on the vault are due to local earthquakes of creep. The direct effects on the repository include rock vibration and displacement on an increasing fault. The indirect effects are changes in the surrounding structure, in the stress field, in the groundwater table, pressure, flux and chemistry. The block movements are controlled mainly by the network of fracture zones. The report deals with the possibilities to monitor by seismic methods slow movements occurring in the bedrock at the local level. The report includes descriptions of instrumentation for recording microearthquakes, the seismic network and an interpretation of the observations. The potential sites for disposal (Kuhmo, Aeaenekoski, Eurajoki) are compared in relation to seismic monitoring. Also the experiences of other investigations and a proposal for microearthquake investigations as well as of prospective developments within monitoring are presented. (28 refs., 17 figs.)

  16. Proposed Food and Drug Administration protective action guides for human food and animal feed: methods and implementation

    International Nuclear Information System (INIS)

    Schmidt, G.D.; Shleien, B.; Chiacchierini, R.P.

    1978-01-01

    The Food and Drug Administration's proposed recommendations to State and local agencies provide guidance on appropriate planning actions necessary for evaluating and preventing radioactive contamination of foods and animal feeds and the control and use of such products should they become contaminated. This presentation will cover the recommendations on implementation of the Preventive and Emergency PAG's. These recommendations include (1) the use of 'Dietary Factors' to obtain PAG's for specific food items from the general guidance, (2) procedures to be used for radionuclide mixtures and other radionuclides, (3) field and laboratory methods for the measurement of the level of contamination in the event of an incident and, (4) protective actions to be implemented by State and local agencies to limit the radiation dose to the public. Specific protective actions which should be considered for implementation when the projected dose exceeds the Preventive PAG are given for application to pasture, milk, fruits and vegetables, and grains. At the Emergency PAG level, the protective action decision is whether condemnation or other disposition is appropriate. (author)

  17. Relating two proposed methods for speedup of algorithms for fitting two- and three-way principal component and related multilinear models

    NARCIS (Netherlands)

    Kiers, Henk A.L.; Harshman, Richard A.

    Multilinear analysis methods such as component (and three-way component) analysis of very large data sets can become very computationally demanding and even infeasible unless some method is used to compress the data and/or speed up the algorithms. We discuss two previously proposed speedup methods.

  18. The qualitative research proposal

    Directory of Open Access Journals (Sweden)

    H Klopper

    2008-09-01

    Full Text Available Qualitative research in the health sciences has had to overcome many prejudices and a number of misunderstandings, but today qualitative research is as acceptable as quantitative research designs and is widely funded and published. Writing the proposal of a qualitative study, however, can be a challenging feat, due to the emergent nature of the qualitative research design and the description of the methodology as a process. Even today, many sub-standard proposals at post-graduate evaluation committees and application proposals to be considered for funding are still seen. This problem has led the researcher to develop a framework to guide the qualitative researcher in writing the proposal of a qualitative study based on the following research questions: (i What is the process of writing a qualitative research proposal? and (ii What does the structure and layout of a qualitative proposal look like? The purpose of this article is to discuss the process of writing the qualitative research proposal, as well as describe the structure and layout of a qualitative research proposal. The process of writing a qualitative research proposal is discussed with regards to the most important questions that need to be answered in your research proposal with consideration of the guidelines of being practical, being persuasive, making broader links, aiming for crystal clarity and planning before you write. While the structure of the qualitative research proposal is discussed with regards to the key sections of the proposal, namely the cover page, abstract, introduction, review of the literature, research problem and research questions, research purpose and objectives, research paradigm, research design, research method, ethical considerations, dissemination plan, budget and appendices.

  19. [Study on the method for the determination of trace boron, molybdenum, silver, tin and lead in geochemical samples by direct current arc full spectrum direct reading atomic emission spectroscopy (DC-Arc-AES)].

    Science.gov (United States)

    Hao, Zhi-hong; Yao, Jian-zhen; Tang, Rui-ling; Zhang, Xue-mei; Li, Wen-ge; Zhang, Qin

    2015-02-01

    The method for the determmation of trace boron, molybdenum, silver, tin and lead in geochemical samples by direct current are full spectrum direct reading atomic emission spectroscopy (DC-Arc-AES) was established. Direct current are full spectrum direct reading atomic emission spectrometer with a large area of solid-state detectors has functions of full spectrum direct reading and real-time background correction. The new electrodes and new buffer recipe were proposed in this paper, and have applied for national patent. Suitable analytical line pairs, back ground correcting points of elements and the internal standard method were selected, and Ge was used as internal standard. Multistage currents were selected in the research on current program, and each current set different holding time to ensure that each element has a good signal to noise ratio. Continuous rising current mode selected can effectively eliminate the splash of the sample. Argon as shielding gas can eliminate CN band generating and reduce spectral background, also plays a role in stabilizing the are, and argon flow 3.5 L x min(-1) was selected. Evaporation curve of each element was made, and it was concluded that the evaporation behavior of each element is consistent, and combined with the effects of different spectrographic times on the intensity and background, the spectrographic time of 35s was selected. In this paper, national standards substances were selected as a standard series, and the standard series includes different nature and different content of standard substances which meet the determination of trace boron, molybdenum, silver, tin and lead in geochemical samples. In the optimum experimental conditions, the detection limits for B, Mo, Ag, Sn and Pb are 1.1, 0.09, 0.01, 0.41, and 0.56 microg x g(-1) respectively, and the precisions (RSD, n=12) for B, Mo, Ag, Sn and Pb are 4.57%-7.63%, 5.14%-7.75%, 5.48%-12.30%, 3.97%-10.46%, and 4.26%-9.21% respectively. The analytical accuracy was

  20. Proposal of flexible atomic and molecular process management for Monte Carlo impurity transport code based on object oriented method

    International Nuclear Information System (INIS)

    Asano, K.; Ohno, N.; Takamura, S.

    2001-01-01

    Monte Carlo simulation code on impurity transport has been developed by several groups to be utilized mainly for fusion related edge plasmas. State of impurity particle is determined by atomic and molecular processes such as ionization, charge exchange in plasma. A lot of atomic and molecular processes have been considered because the edge plasma has not only impurity atoms, but also impurity molecules mainly related to chemical erosion of carbon materials, and their cross sections have been given experimentally and theoretically. We need to reveal which process is essential in a given edge plasma condition. Monte Carlo simulation code, which takes such various atomic and molecular processes into account, is necessary to investigate the behavior of impurity particle in plasmas. Usually, the impurity transport simulation code has been intended for some specific atomic and molecular processes so that the introduction of a new process forces complicated programming work. In order to evaluate various proposed atomic and molecular processes, a flexible management of atomic and molecular reaction should be established. We have developed the impurity transport simulation code based on object-oriented method. By employing object-oriented programming, we can handle each particle as 'object', which enfolds data and procedure function itself. A user (notice, not programmer) can define property of each particle species and the related atomic and molecular processes and then each 'object' is defined by analyzing this information. According to the relation among plasma particle species, objects are connected with each other and change their state by themselves. Dynamic allocation of these objects to program memory is employed to adapt for arbitrary number of species and atomic/molecular reactions. Thus we can treat arbitrary species and process starting from, for instance, methane and acetylene. Such a software procedure would be useful also for industrial application plasmas

  1. Comparison of conventional full spine radiographs and fluoroscopic scanning method in young patients with idiopathic scoliosis; Vergleich von konventioneller Wirbelsaeulenganzaufnahme und fluoroskopischer Scan-Methode bei jungen Patienten mit idiopathischer Skoliose

    Energy Technology Data Exchange (ETDEWEB)

    Schaefer, J.; Kottke, R.; Claussen, C. [Abt. fuer Radiologische Diagnostik, Universitaetsklinikum Tuebingen (Germany); Kluba, T.; Niemeyer, T.; Hahnfeldt, T. [Klinik und Poliklinik fuer Orthopaedie, Universitaetsklinikum Tuebingen (Germany); Vonthein, R. [Inst. fuer Medizinische Biometrie, Universitaetsklinikum Tuebingen (Germany); Kamm, K.F. [Philips Medizin Systeme GmbH, Hamburg (Germany)

    2005-08-01

    Purpose: evaluation of low-dose full spine radiographs using fluoroscopic images for the assessment of the Cobb angle measurement in patients with scoliosis. Material and methods: twenty-one consecutive patients (aged 10-27 years, mean age 14 years) with a conventional full spine examination (film speed class 800) underwent a follow-up exam using digital pulsed fluoroscopy (Multi Diagnost 4, Philips Medical Systems, Eindhoven, The Netherlands). The mean follow-up was 9 months. During a synchronized scan with a C-arm speed of 4 cm/sec fluoroscopic images were stored with a pulsed frequency of 3 images per second. The single images were merged and reconstructed to one image with the software easy spine (Philips medical Systems, Eindhoven, The Netherlands). The corresponding dose-area product values (DAP) of both methods were compared. Three independent observers assessed Cobb angles and image quality for each technique. Results: the mean DAP values for conventional imaging was 94.9 cGy x cm{sup 2} and for fluoroscopy 7.8 cGy x cm{sup 2}, respectively. A significant dose reduction of 91.8% (CI 91% to 95%) was calculated. The average absolute angle difference between the observers was found to be 2.7 for conventional imaging and 2.4 for the fluoroscopic method. Interobserver standard deviation of 2.9 was lower than the 5.3 for conventional images. Image quality was better in the conventional images. Conclusion: using the scanning method, we could achieve a mean reduction of the radiation dose of 92%, while the accuracy of the Cobb angle measurements was comparable for both techniques despite of reduced image quality of digital fluoroscopy. (orig.)

  2. Development of a simplified and dynamic method for double glazing façade with night insulation and validated by full-scale façade element

    DEFF Research Database (Denmark)

    Liu, Mingzhe; Wittchen, Kim Bjarne; Heiselberg, Per

    2013-01-01

    The study aims to develop a simplified calculation method to simulate the performance of double glazing fac¸ ade with night insulation. This paper describes the method to calculate the thermal properties (Uvalue) and comfort performance (internal surface temperature of glazing) of the double...... with night insulation is calculated and compared with that of the facade without the night insulation. Based on standards EN 410 and EN 673, the method takes the thermal mass of glazing and the infiltration between the insulation layer and glazing into account. Furthermore it is capable of implementing whole...

  3. Method for the determination of the spectral composition of power-full energy-rich deuteron bundles generated in the plasma focus

    International Nuclear Information System (INIS)

    Philippow, N.W.; Philippowa, T.I.

    1977-01-01

    A method is presented which allows a quantitative determination of the spectral composition of a high power deuterium bunch produced in noncylindrical Z-pinch type systems when the plasma shell is increased. The bunch moves in the normal direction, i.e. from the anode to the region behind the cathodes. The method is based on the principle of a time-of-flight spectrometer, where the neutron scintillation detector signal is processed appropriately and displayed on a scope. The neutrons are produced by the 12 C(d,n) 13 N-reaction in the carbon target when hit by a deuterium bunch. These investigations have been performed in parallel with the method based on a comparison of carbon- and aluminium target activities. This method has been used in the past by R. Gallickson and G. Salin in the Livermore Laboratory for the same purpose but has now untergone some improvements. (orig.) [de

  4. Wastewater Treatment Anaerobic Digester Foaming Prevention and Control Methods - Literature Review and Survey - Full-Scale Studies (WERF Report INFR1SG10)

    Science.gov (United States)

    This project addresses the issue of anaerobic digester (AD) foaming in different water resource recovery facilities (WRRFs). This two-volume report is a compilation of an AD foaming literature review, a plant survey, and findings from full-scale studies. The literature review hel...

  5. Full factorial design applied to the synthesis of Pd-?Ag nanobars by the polyol method and the perspective for ethanol oxidation

    OpenAIRE

    Carrera-Cerritos, Raul; Ponce de Leon, Carlos; Ledesma-Garcia, J.; Fuentes-Ramirez, R.; Arriaga, L.G.

    2014-01-01

    Full factorial design methodology was applied to the synthesis and optimization of Pd–Ag nanobars usingthe polyol process as the reducer. The concentration of Br? ions, the temperature and the reaction timewere selected as factors to study, whereas the yield (% nanobars) was the response to be analyzed. Thenanoparticles were characterized by X-ray diffraction, energy-dispersive X-ray spectroscopy,transmission electron microscopy, high-resolution transmission electron microscopy and X-rayphoto...

  6. Development and sensitivity study of a simplified and dynamic method for double glazing facade and verified by a full-scale façade element

    DEFF Research Database (Denmark)

    Liu, Mingzhe; Wittchen, Kim Bjarne; Heiselberg, Per

    2014-01-01

    The research aims to develop a simplified calculation method for double glazing facade to calculate its thermal and solar properties (U and g value) together with comfort performance (internal surface temperature of the glazing). Double glazing is defined as 1D model with nodes representing......, taking the thermal mass of the glazing into account. In addition, angle and spectral dependency of solar characteristic is also considered during the calculation. By using the method, it is possible to calculate whole year performance at different time steps, which makes it a time economical and accurate...

  7. Teaching an Interdisciplinary Graduate-Level Methods Course in an Openly-Networked Connected Learning Environment: A Glass Half-Full

    Science.gov (United States)

    Secret, Mary; Bryant, Nita L.; Cummings, Cory R.

    2017-01-01

    Our paper describes the design and delivery of an online interdisciplinary social science research methods course (ISRM) for graduate students in sociology, education, social work, and public administration. Collaborative activities and learning took place in two types of computer-mediated learning environments: a closed Blackboard course…

  8. Method translation and full metadata transfer from thermal to differential flow modulated comprehensive two dimensional gas chromatography: Profiling of suspected fragrance allergens.

    Science.gov (United States)

    Cordero, Chiara; Rubiolo, Patrizia; Reichenbach, Stephen E; Carretta, Andrea; Cobelli, Luigi; Giardina, Matthew; Bicchi, Carlo

    2017-01-13

    The possibility to transfer methods from thermal to differential-flow modulated comprehensive two-dimensional gas chromatographic (GC×GC) platforms is of high interest to improve GC×GC flexibility and increase the compatibility of results from different platforms. The principles of method translation are here applied to an original method, developed for a loop-type thermal modulated GC×GC-MS/FID system, suitable for quali-quantitative screening of suspected fragrance allergens. The analysis conditions were translated to a reverse-injection differential flow modulated platform (GC×2GC-MS/FID) with a dual-parallel secondary column and dual detection. The experimental results, for a model mixture of suspected volatile allergens and for raw fragrance mixtures of different composition, confirmed the feasibility of translating methods by preserving 1 D elution order, as well as the relative alignment of resulting 2D peak patterns. A correct translation produced several benefits including an effective transfer of metadata (compound names, MS fragmentation pattern, response factors) by automatic template transformation and matching from the original/reference method to its translated counterpart. The correct translation provided: (a) 2D pattern repeatability, (b) MS fragmentation pattern reliability for identity confirmation, and (c) comparable response factors and quantitation accuracy within a concentration range of three orders of magnitude. The adoption of a narrow bore (i.e. 0.1mm d c ) first-dimension column to operate under close-to-optimal conditions with the differential-flow modulation GC×GC platform was also advantageous in halving the total analysis under the translated conditions. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Full non-linear treatment of the global thermospheric wind system. I - Mathematical method and analysis of forces. II - Results and comparison with observations

    Science.gov (United States)

    Blum, P. W.; Harris, I.

    1975-01-01

    The equations of horizontal motion of the neutral atmosphere between 120 and 500 km are integrated with the inclusion of all nonlinear terms of the convective derivative and the viscous forces due to vertical and horizontal velocity gradients. Empirical models of the distribution of neutral and charged particles are assumed to be known. The model of velocities developed is a steady state model. In Part I the mathematical method used in the integration of the Navier-Stokes equations is described and the various forces are analyzed. Results of the method given in Part I are presented with comparison with previous calculations and observations of upper atmospheric winds. Conclusions are that nonlinear effects are only significant in the equatorial region, especially at solstice conditions and that nonlinear effects do not produce any superrotation.

  10. Fast and robust methods for full genome sequencing of Porcine Reproductive and Respiratory Syndrome Virus (PRRSV) Type 1 and Type 2

    DEFF Research Database (Denmark)

    Kvisgaard, Lise Kirstine; Hjulsager, Charlotte Kristiane; Fahnøe, Ulrik

    . In the present study, fast and robust methods for long range RT-PCR amplification and subsequent next generation sequencing (NGS) of PRRSV Type 1 and Type 2 viruses were developed and validated on nine Type 1 and nine Type 2 PRRSV viruses. The methods were shown to generate robust and reliable sequences both...... on primary material and cell culture adapted viruses and the protocols were shown to perform well on all three NGS platforms tested (Roche 454 FLX, Illumina HiSeq 2000, and Ion Torrent PGM™ Sequencer). To complete the sequences at the 5’ end, 5’ Rapid Amplification of cDNA Ends (5’ RACE) was conducted...... followed by cycle sequencing of clones. The genome lengths were determined to be 14,876-15,098 and 15,342-15,408 nucleotides long for the Type 1 and Type 2 strains, respectively. These methods will greatly facilitate the generation of more complete genome PRRSV sequences globally which in turn may lead...

  11. Numerical Differentiation Methods for Computing Error Covariance Matrices in Item Response Theory Modeling: An Evaluation and a New Proposal

    Science.gov (United States)

    Tian, Wei; Cai, Li; Thissen, David; Xin, Tao

    2013-01-01

    In item response theory (IRT) modeling, the item parameter error covariance matrix plays a critical role in statistical inference procedures. When item parameters are estimated using the EM algorithm, the parameter error covariance matrix is not an automatic by-product of item calibration. Cai proposed the use of Supplemented EM algorithm for…

  12. A full dimensional investigation of infrared spectroscopy of the RbCs dimer using the multi-configuration time-dependent Hartree method

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Huihui; Yang, Yonggang, E-mail: ygyang@sxu.edu.cn; Xiao, Liantuan; Jia, Suotang [State Key Laboratory of Quantum Optics and Quantum Optics Devices, Institute of Laser Spectroscopy, Shanxi University, Taiyuan 030006 (China)

    2013-12-28

    The geometry and infrared absorption spectrum of (RbCs){sub 2} have been studied by full dimensional quantum dynamics simulations. For this purpose, the potential energy and dipole moment surfaces are generated by means of a cluster expansion with all two and three mode correlations, and fitted to analytical expressions with negligible deviations. Accordingly, the ground state (RbCs){sub 2} has a diamond geometry with D{sub 2h} symmetry. The infrared spectrum with frequencies up to 120 cm{sup −1}, exhibits rich details of the fundamentals, overtones, and combination bands; the highest fundamental frequency of (RbCs){sub 2} is only 40.26 cm{sup −1}. The present study unravels important details of the interactions between the widely investigated ultracold RbCs molecules.

  13. A full quantum analysis of the Stern–Gerlach experiment using the evolution operator method: analyzing current issues in teaching quantum mechanics

    International Nuclear Information System (INIS)

    Benítez Rodríguez, E; Aguilar, L M Arévalo; Martínez, E Piceno

    2017-01-01

    To the quantum mechanics specialists community it is a well-known fact that the famous original Stern–Gerlach experiment (SGE) produces entanglement between the external degrees of freedom (position) and the internal degree of freedom (spin) of silver atoms. Despite this fact, almost all textbooks on quantum mechanics explain this experiment using a semiclassical approach, where the external degrees of freedom are considered classical variables, the internal degree is treated as a quantum variable, and Newton's second law is used to describe the dynamics. In the literature there are some works that analyze this experiment in its full quantum mechanical form. However, astonishingly, to the best of our knowledge the original experiment, where the initial states of the spin degree of freedom are randomly oriented coming from the oven, has not been analyzed yet in the available textbooks using the Schrödinger equation (to the best of our knowledge there is only one paper that treats this case: Hsu et al (2011 Phys. Rev. A 83 012109)). Therefore, in this contribution we use the time-evolution operator to give a full quantum mechanics analysis of the SGE when the initial state of the internal degree of freedom is completely random, i.e. when it is a statistical mixture. Additionally, as the SGE and the development of quantum mechanics are heavily intermingled, we analyze some features and drawbacks in the current teaching of quantum mechanics. We focus on textbooks that use the SGE as a starting point, based on the fact that most physicist do not use results from physics education research, and comment on traditional pedagogical attitudes in the physics community. (paper)

  14. SU-F-J-142: Proposed Method to Broaden Inclusion Potential of Patients Able to Use the Calypso Tracking System in Prostate Radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Fiedler, D; Kuo, H; Bodner, W; Tome, W [Montefiore Medical Center, Bronx, NY (United States)

    2016-06-15

    Purpose: To introduce a non-standard method of patient setup, using BellyBoard immobilization, to better utilize the localization and tracking potential of an RF-beacon system with EBRT for prostate cancer. Methods: An RF-beacon phantom was imaged using a wide bore CT scanner, both in a standard level position and with a known rotation (4° pitch and 7.5° yaw). A commercial treatment planning system (TPS) was used to determine positional coordinates of each beacon, and the centroid of the three beacons for both setups. For each setup at the Linac, kV AP and Rt Lateral images were obtained. A full characterization of the RF-beacon system in clinical mode was completed for various beacons’ array-to-centroid distances, which includes vertical, lateral, and longitudinal offset data, as well as pitch and yaw offset measurements for the tilted phantom. For the single patient who has been setup using the proposed BellyBoard method, a supine simulation was first obtained. When abdominal protrusion was found to be exceeding the limits of the RF-Beacon system through distance-based analysis in the TPS, the patient is re-simulated prone with the BellyBoard. Array to centroid distance is measured again in the TPS, and if found to be within the localization or tracking region it is applied. Results: Characterization of limitations for the RF-beacon system in clinical mode showed acceptable consistency of offset determination for phantom setup accuracy. The nonstandard patient setup method reduced the beacons’ centroid-to-array distance by 8.32cm, from 25.13cm to 16.81cm; completely out of tracking range (greater than 20cm) to within setup tracking range (less than 20cm). Conclusion: Using the RF-beacon system in combination with this novel patient setup can allow patients who would otherwise not be candidates for beacon enhanced EBRT to now be able to benefit from the reduced PTV margins of this treatment method.

  15. SU-F-J-142: Proposed Method to Broaden Inclusion Potential of Patients Able to Use the Calypso Tracking System in Prostate Radiotherapy

    International Nuclear Information System (INIS)

    Fiedler, D; Kuo, H; Bodner, W; Tome, W

    2016-01-01

    Purpose: To introduce a non-standard method of patient setup, using BellyBoard immobilization, to better utilize the localization and tracking potential of an RF-beacon system with EBRT for prostate cancer. Methods: An RF-beacon phantom was imaged using a wide bore CT scanner, both in a standard level position and with a known rotation (4° pitch and 7.5° yaw). A commercial treatment planning system (TPS) was used to determine positional coordinates of each beacon, and the centroid of the three beacons for both setups. For each setup at the Linac, kV AP and Rt Lateral images were obtained. A full characterization of the RF-beacon system in clinical mode was completed for various beacons’ array-to-centroid distances, which includes vertical, lateral, and longitudinal offset data, as well as pitch and yaw offset measurements for the tilted phantom. For the single patient who has been setup using the proposed BellyBoard method, a supine simulation was first obtained. When abdominal protrusion was found to be exceeding the limits of the RF-Beacon system through distance-based analysis in the TPS, the patient is re-simulated prone with the BellyBoard. Array to centroid distance is measured again in the TPS, and if found to be within the localization or tracking region it is applied. Results: Characterization of limitations for the RF-beacon system in clinical mode showed acceptable consistency of offset determination for phantom setup accuracy. The nonstandard patient setup method reduced the beacons’ centroid-to-array distance by 8.32cm, from 25.13cm to 16.81cm; completely out of tracking range (greater than 20cm) to within setup tracking range (less than 20cm). Conclusion: Using the RF-beacon system in combination with this novel patient setup can allow patients who would otherwise not be candidates for beacon enhanced EBRT to now be able to benefit from the reduced PTV margins of this treatment method.

  16. Development and full validation of an UPLC-MS/MS method for the quantification of the plant-derived alkaloid indirubin in rat plasma.

    Science.gov (United States)

    Jähne, Evelyn A; Sampath, Chethan; Butterweck, Veronika; Hamburger, Matthias; Oufir, Mouhssin

    2016-09-05

    An UPLC-MS/MS method for the quantification of indirubin in lithium heparinized rat plasma was developed and validated according to current international guidelines. Indirubin was extracted from rat plasma by using Waters Ostro™ pass-through sample preparation plates. The method was validated with a LLOQ of 5.00ng/mL and an ULOQ of 500ng/mL. The calibration curve was fitted by least-square quadratic regression, and a weighting factor of 1/X was applied. Recoveries of indirubin and I.S. were consistent and ≥75.5%. Stability studies demonstrated that indirubin was stable in lithium heparinized rat plasma for at least 3 freeze/thaw cycles, for 3h at RT, for 96h in the autosampler at 10°C, and for 84days when stored below -65°C. Preliminary pharmacokinetic (PK) data were obtained from Sprague Dawley rats after intravenous administration of indirubin (2mg/kg b.w.) and blood sampling up to 12h after injection. PK parameters were determined by non-compartmental analysis. Indirubin had a half-life (t1/2) of 35min, and a relatively high clearance (CL) of 2.71L/h/kg. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Proposed method for assigning metric tons of heavy metal values to defense high-level waste forms to be disposed of in a geologic repository

    International Nuclear Information System (INIS)

    1987-08-01

    A proposed method is described for assigning an equivalent metric ton heavy metal (eMTHM) value to defense high-level waste forms to be disposed of in a geologic repository. This method for establishing a curie equivalency between defense high-level waste and irradiated commercial fuel is based on the ratio of defense fuel exposure to the typical commercial fuel exposure, MWd/MTHM. application of this technique to defense high-level wastes is described. Additionally, this proposed technique is compared to several alternate calculations for eMTHM. 15 refs., 2 figs., 10 tabs

  18. Proposed design method for large-stone asphalt and the implementation thereof in the rehabilitation of an airport pavement.

    CSIR Research Space (South Africa)

    Grobler, JE

    1992-07-01

    Full Text Available This paper addresses the development of a design procedure for large-stone asphalt, the implementation thereof in two sets of trial sections, the correlation of engineering properties obtained in the laboratory with field properties...

  19. Concurrent myotomy and tunneling after establishment of a half tunnel instead of myotomy after establishment of a full tunnel: a more efficient method of peroral endoscopic myotomy.

    Science.gov (United States)

    Philips, George M; Dacha, Sunil; Keilin, Steve A; Willingham, Field F; Cai, Qiang

    2016-04-01

    Peroral endoscopic myotomy (POEM) is a time-consuming and challenging procedure. Traditionally, the myotomy is done after the submucosal tunnel has been completed. Starting the myotomy earlier, after submucosal tunneling is half completed (concurrent myotomy and tunneling), may be more efficient. This study aims to assess if the method of concurrent myotomy and tunneling may decrease the procedural time and be efficacious. This is a retrospective case series of patients who underwent modified POEM (concurrent myotomy and tunneling) or traditional POEM at a tertiary care medical center. Modified POEM or traditional POEM was performed at the discretion of the endoscopist in patients presenting with achalasia. The total procedural duration, myotomy duration, myotomy length, and time per unit length of myotomy were recorded for both modified and traditional POEM. Modified POEM was performed in 6 patients whose mean age (± standard deviation [SD]) was 58 ± 13.3 years. Of these, 5 patients had type II achalasia and 1 patient had esophageal dysmotility. The mean Eckardt score (± SD) before the procedure was 8.8 ± 1.3. The modified technique was performed in 47 ± 8 minutes, with 6 ± 1 minutes required per centimeter of myotomy and 3 ± 1 minutes required per centimeter of submucosal space. The Eckardt score was 3 ± 1.1 at 1 month and 3 ± 2.5 at 3 months. The procedure time for modified POEM was significantly shorter than that for traditional POEM. Modified POEM with short submucosal tunneling may be more efficient than traditional POEM with long submucosal tunneling, and outcomes may be equivalent over short-term follow-up. Long-term data and randomized controlled studies are needed to compare the clinical efficacy of modified POEM with that of the traditional method.

  20. Evaluation of bank filtration as a pretreatment method for the provision of hygienically safe drinking water in Norway: results from monitoring at two full-scale sites

    Science.gov (United States)

    Kvitsand, Hanne M. L.; Myrmel, Mette; Fiksdal, Liv; Østerhus, Stein W.

    2017-08-01

    Two case studies were carried out in central Norway in order to assess the performance of bank filtration systems in cold-climate fluvial aquifers relying on recharge from humic-rich surface waters with moderate microbial contamination. Three municipal wells and two surface-water sources at operative bank filtration systems were monitored for naturally occurring bacteriophages, fecal indicators, natural organic matter (NOM) and physico-chemical water quality parameters during a 4-month period. Aquifer passage effectively reduced the microorganism and NOM concentrations at both study sites. Bacteriophages were detected in 13 of 16 (81%) surface-water samples and in 4 of 24 (17%) well-water samples, and underwent 3 ± 0.3 log10 reduction after 50-80-m filtration and 20-30 days of subsurface passage. NOM reductions (color: 74-97%; dissolved organic carbon: 54-80%; very hydrophobic acids: 70%) were similar to those achieved by conventional water-treatment processes and no further treatment was needed. Both groundwater dilution and sediment filtration contributed to the hygienic water quality improvements, but sediment filtration appeared to be the most important process with regard to microbial and NOM reductions. A strengths-weaknesses-opportunities-threats analysis showed that bank filtration technology has a high potential as a pretreatment method for the provision of hygienically safe drinking water in Norway.

  1. Accuracy of full-arch scans using intraoral and extraoral scanners: an in vitro study using a new method of evaluation.

    Science.gov (United States)

    Muallah, Jonas; Wesemann, Christian; Nowak, Roxana; Robben, Jan; Mah, James; Pospiech, Peter; Bumann, Axel

    The aim of this study was to compare the accuracy of six intraoral scanners as regards clinically relevant distances using a new method of evaluation. An additional objective was to compare intraoral scanners with the indirect digitization of model scanners. A resin master model was created by 3D printing and drilled in five places to reflect the following distances: intermolar width (IMW), intercanine width (ICW), and arch length (AL). To determine a gold standard, the distances were measured with a coordinate measuring instrument (Zeiss O-Inspect 422). The master model was scanned 37 times with the following intraoral scanners: Apollo DI (Sirona), CS 3500 (Carestream Dental), iTero (Cadent), PlanScan (Planmeca), Trios (3Shape), and True Definition (3M Espe), and indirectly digitized with the OrthoX Scan (Dentaurum). The digital models were then measured, and deviations from the gold standard calculated. Significant differences were found between the devices. Among the intraoral scanners, Trios and iTero showed the most accurate results, although CS 3500, True Definition, and Apollo DI achieved comparable results. PlanScan demonstrated the highest deviations from the gold standard, and presented a high standard deviation (SD). Direct digitization revealed comparable (and, in fact, slightly higher) accuracy than indirect digitization. Both indirect digitization and most of the intraoral scanners were therefore demonstrated to be suitable for use in the orthodontic office, with the exception of PlanScan, which did not meet the demands of individual orthodontic treatment.

  2. A dissipation based method for identifying hererogeneous material properties using full-field measurements [Une approche en dissipation pour l'identification de proprié tés matériaux hétérogènes à partir de mesures de champs

    KAUST Repository

    Lubineau, Gilles; Florentin, É ric; Moussawi, Ali; Blaysat, Benoî t

    2012-01-01

    The full field measurement technique has become a popular technique for the quick identification of complex and/or heterogeneous-in-space material behaviors. Based on the rich available corpus of information, this technique makes possible to identify complex evolution laws using few highly heterogeneous testing. Multiple techniques have been proposed up to now. Here, we detail the application of the constitutive error relation to the identification of linear elastic material models.Then, the natural extension of the constitutive equation gap method through a dissipation gap method is discussed for the identification of material behaviors involving dissipation. 2D reference examples are provided for each method. © 2012 EDP Sciences.

  3. [A study for testing the antifungal susceptibility of yeast by the Japanese Society for Medical Mycology (JSMM) method. The proposal of the modified JSMM method 2009].

    Science.gov (United States)

    Nishiyama, Yayoi; Abe, Michiko; Ikeda, Reiko; Uno, Jun; Oguri, Toyoko; Shibuya, Kazutoshi; Maesaki, Shigefumi; Mohri, Shinobu; Yamada, Tsuyoshi; Ishibashi, Hiroko; Hasumi, Yayoi; Abe, Shigeru

    2010-01-01

    The Japanese Society for Medical Mycology (JSMM) method used for testing the antifungal susceptibility of yeast, the MIC end point for azole antifungal agents, is currently set at IC(80). It was recently shown, however that there is an inconsistency in the MIC value between the JSMM method and the CLSI M27-A2 (CLSI) method, in which the end- point was to read as IC(50). To resolve this discrepancy and reassess the JSMM method, the MIC for three azoles, fluconazole, itraconazole and voriconazole were compared to 5 strains of each of the following Candida species: C. albicans, C. glabrata, C. tropicalis, C. parapsilosis and C. krusei, for a total of 25 comparisons, using the JSMM method, a modified JSMM method, and the CLSI method. The results showed that when the MIC end- point criterion of the JSMM method was changed from IC(80) to IC(50) (the modified JSMM method) , the MIC value was consistent and compatible with the CLSI method. Finally, it should be emphasized that the JSMM method, using a spectrophotometer for MIC measurement, was superior in both stability and reproducibility, as compared to the CLSI method in which growth was assessed by visual observation.

  4. Full Digital Short Circuit Protection for Advanced IGBTs

    OpenAIRE

    谷村, 拓哉; 湯浅, 一史; 大村, 一郎

    2011-01-01

    A full digital short circuit protection method for advanced IGBTs has been proposed and experimentally demonstrated for the first time. The method employs combination of digital circuit, the gate charge sense instead of the conventional sense IGBT and analog circuit configuration. Digital protection scheme has significant advantages in thevprotection speed and flexibility.

  5. Proposal and Its Evaluation of a Shoulder-Surfing Attack Resistant Authentication Method:Secret Tap with Double Shift

    OpenAIRE

    Yoshihiro Kita; Fumio Sugai; MiRang Park; Naonobu Okazaki

    2015-01-01

    Recently, mobile terminals such as smartphones have come into widespread use. Most of such mobile terminals store several types of important data, such as personal information. Therefore, it is necessary to lock and unlock terminals using a personal authentication method such as personal identification numbers (PINs) in order to prevent data theft. However, most existing authentication methods have a common problem referred to here as “shoulder-surfing”, in which authentication information is...

  6. Testing the ability of a proposed geotechnical based method to evaluate the liquefaction potential analysis subjected to earthquake vibrations

    Science.gov (United States)

    Abbaszadeh Shahri, A.; Behzadafshar, K.; Esfandiyari, B.; Rajablou, R.

    2010-12-01

    During the earthquakes a number of earth dams have had severe damages or suffered major displacements as a result of liquefaction, thus modeling by computer codes can provide a reliable tool to predict the response of the dam foundation against earthquakes. These modeling can be used in the design of new dams or safety assessments of existing ones. In this paper, on base of the field and laboratory tests and by combination of several software packages a seismic geotechnical based analysis procedure is proposed and verified by comparison with computer model tests, field and laboratory experiences. Verification or validation of the analyses relies to ability of the applied computer codes. By use of Silakhor earthquake (2006, Ms 6.1) and in order to check the efficiency of the proposed framework, the procedure is applied to the Korzan earth dam of Iran which is located in Hamedan Province to analyze and estimate the liquefaction and safety factor. Design and development of a computer code by authors which named as “Abbas Converter” with graphical user interface which operates as logic connecter function that can computes and models the soil profiles is the critical point of this study and the results are confirm and proved the ability of the generated computer code on evaluation of soil behavior under the earthquake excitations. Also this code can make and render facilitate this study more than previous have done, and take over the encountered problem.

  7. Isotope dilution/mass spectrometry of serum cholesterol with [3,4-13C]cholesterol: proposed definitive method

    International Nuclear Information System (INIS)

    Pelletier, O.; Wright, L.A.; Breckenridge, W.C.

    1987-01-01

    We describe a new gas-chromatographic/mass-spectrometric (GC/MS) isotope-dilution method for determination of serum cholesterol. The method has been fully optimized and documented to provide the high accuracy and precision expected for a Definitive Method. In the presence of [3,4- 13 C]cholesterol, cholesteryl esters in serum are hydrolyzed under optimum conditions and the entire cholesterol pool is extracted and derivatized to silyl ethers. The cholesterol derivatives are resolved from other sterols by gas-liquid chromatography on a fused silica column, and selected ions characteristic of cholesterol and the [3,4- 13 C]cholesterol are monitored with a GC/MS quandrupole system. We estimated the cholesterol content of samples by bracketing each sample with standards of comparable cholesterol concentration that also contained the [3,4- 13 C]cholesterol. The procedure was highly reproducible (CV less than 0.5%), better accuracy and precision being obtained with [3,4- 13 C]cholesterol than with heptadeuterated cholesterol. Mean values per gram of dry serum for one serum pool assayed by this method and that of the National Bureau of Standards differed by 0.5%. We conclude that the method satisfies the criteria for a Definitive Method

  8. A novel method of TVTS in the TS-3 device and the proposal of its application to a large device

    International Nuclear Information System (INIS)

    Tokimatsu, K.; Hayashi, N.; Ueda, Y.; Ono, Y.; Katsurai, M.

    1997-01-01

    A novel method of television Thomson scattering (TVTS) has been developed in the TS-3 device. In this system, a framing camera is located between a spectroscope and a close coupled device camera. This framing camera can take two successive frames from the exit of the spectroscope. The time interval is of 500 ns between those two frames. Because of the shortness of this time interval, the background light is negligible; moreover TVTS is applicable to the TS-3 device whose plasma lifetime is about 150 μs. This method indicates the possibility of not only high spatial resolution but also time repetition in a simple system. (orig.)

  9. Study of a proposed method of uranium concentration determination using low-energy γ-ray spectroscopy

    International Nuclear Information System (INIS)

    Rossiter, K.G.; Tang, J.C.N.

    1980-01-01

    The problems associated with in-situ uranium assaying are discussed, especially in relation to the secular disequilibrium between the parent uranium and its radioactive daughters. A detailed study of the gamma-spectra of some natural uranium bearing ore and mineral samples was performed using a high resolution Ge(Li) detector. A method of spectroscopic analysis of the low energy gamma-rays of U-238 and its daughter Th-234, using a proportional counter and a series of Ross filters, was found to be feasible. The application of such a method to uranium assaying in natural ore bodies is discussed

  10. PROPOSED ASTM METHOD FOR THE DETERMINATION OF ASBESTOS IN AIR BY TEM AND INFORMATION ON INTERFERING FIBERS

    Science.gov (United States)

    The draft of the ASTM Test Method for air entitled: "Airborne Asbestos Concentration in Ambient and Indoor Atmospheres as Determined by Transmission Electron Microscopy Direct Transfer (TEM)" (ASTM Z7077Z) is an adaptation of the International Standard, ISO 10312. It is currently...

  11. A proposed method to assess the damage risk of future climate change to museum objects in historic buildings

    NARCIS (Netherlands)

    Huijbregts, Z.; Kramer, R.P.; Martens, M.H.J.; Schijndel, van A.W.M.; Schellen, H.L.

    2012-01-01

    Future climate change is expected to have a critical effect on valuable museum collections that are housed in historic buildings. Changes of the indoor environment in the building affect the microclimate around the museum objects and may cause damage to the collection. In this study, a method is

  12. Scientific Opinion on a composting method proposed by Portugal as a heat treatment to eliminate pine wood nematode from the bark of pine trees

    DEFF Research Database (Denmark)

    Baker, R.; Candresse, T.; Dormannsné Simon, E.

    2010-01-01

    Following a request from the European Commission, the Panel on Plant Health was asked to deliver a scientific opinion on the appropriateness of a composting method proposed by Portugal as a heat treatment to eliminate pine wood nematode (PWN), Bursaphelenchus xylophilus (Steiner and Buhrer) Nickle......) insufficient evidence on the sampling methodology is provided to determine the reliability of the testing method provided by the Portuguese document to determine freedom from PWN. Although there is potential for development of a composting method as a heat treatment to eliminate PWN from bark of pine trees...

  13. Full closure strategic analysis.

    Science.gov (United States)

    2014-07-01

    The full closure strategic analysis was conducted to create a decision process whereby full roadway : closures for construction and maintenance activities can be evaluated and approved or denied by CDOT : Traffic personnel. The study reviewed current...

  14. Withdrawal of corticosteroids in inflammatory bowel disease patients after dependency periods ranging from 2 to 45 years: a proposed method.

    LENUS (Irish Health Repository)

    Murphy, S J

    2012-02-01

    BACKGROUND: Even in the biologic era, corticosteroid dependency in IBD patients is common and causes a lot of morbidity, but methods of withdrawal are not well described. AIM: To assess the effectiveness of a corticosteroid withdrawal method. METHODS: Twelve patients (10 men, 2 women; 6 ulcerative colitis, 6 Crohn\\'s disease), median age 53.5 years (range 29-75) were included. IBD patients with quiescent disease refractory to conventional weaning were transitioned to oral dexamethasone, educated about symptoms of the corticosteroid withdrawal syndrome (CWS) and weaned under the supervision of an endocrinologist. When patients failed to wean despite a slow weaning pace and their IBD remaining quiescent, low dose synthetic ACTH stimulation testing was performed to assess for adrenal insufficiency. Multivariate analysis was performed to assess predictors of a slow wean. RESULTS: Median durations for disease and corticosteroid dependency were 21 (range 3-45) and 14 (range 2-45) years respectively. Ten patients (83%) were successfully weaned after a median follow-up from final wean of 38 months (range 5-73). Disease flares occurred in two patients, CWS in five and ACTH testing was performed in 10. Multivariate analysis showed that longer duration of corticosteroid use appeared to be associated with a slower wean (P = 0.056). CONCLUSIONS: Corticosteroid withdrawal using this protocol had a high success rate and durable effect and was effective in patients with long-standing (up to 45 years) dependency. As symptoms of CWS mimic symptoms of IBD disease flares, gastroenterologists may have difficulty distinguishing them, which may be a contributory factor to the frequency of corticosteroid dependency in IBD patients.

  15. Number needed to benefit from information (NNBI): proposal from a mixed methods research study with practicing family physicians.

    Science.gov (United States)

    Pluye, Pierre; Grad, Roland M; Johnson-Lafleur, Janique; Granikov, Vera; Shulha, Michael; Marlow, Bernard; Ricarte, Ivan Luiz Marques

    2013-01-01

    We wanted to describe family physicians' use of information from an electronic knowledge resource for answering clinical questions, and their perception of subsequent patient health outcomes; and to estimate the number needed to benefit from information (NNBI), defined as the number of patients for whom clinical information was retrieved for 1 to benefit. We undertook a mixed methods research study, combining quantitative longitudinal and qualitative research studies. Participants were 41 family physicians from primary care clinics across Canada. Physicians were given access to 1 electronic knowledge resource on handheld computer in 2008-2009. For the outcome assessment, participants rated their searches using a validated method. Rated searches were examined during interviews guided by log reports that included ratings. Cases were defined as clearly described searches where clinical information was used for a specific patient. For each case, interviewees described information-related patient health outcomes. For the mixed methods data analysis, quantitative and qualitative data were merged into clinical vignettes (each vignette describing a case). We then estimated the NNBI. In 715 of 1,193 searches for information conducted during an average of 86 days, the search objective was directly linked to a patient. Of those searches, 188 were considered to be cases. In 53 cases, participants associated the use of information with at least 1 patient health benefit. This finding suggested an NNBI of 14 (715/53). The NNBI may be used in further experimental research to compare electronic knowledge resources. A low NNBI can encourage clinicians to search for information more frequently. If all searches had benefits, the NNBI would be 1. In addition to patient benefits, learning and knowledge reinforcement outcomes are frequently reported.

  16. Método de custeio UEP: uma proposta para uma agroindústria avícola = UEP costing method: a proposal for an aviary agribusiness

    Directory of Open Access Journals (Sweden)

    Silvana Milanese

    2012-07-01

    Full Text Available O objetivo geral deste trabalho é elaborar uma proposta de implantação do método de custeio Unidade de Esforço de Produção (UEP para uma agroindústria avícola. Para tanto, realiza-se uma pesquisa descritiva, com abordagem do problema de forma qualitativa e quantitativa, por meio de um estudo de caso. Os resultados apontam que: a a empresa possui um processo produtivo diferente, pois seus produtos finais são procedentes da desmontagem de uma única matéria-prima, o frango; b os custos de transformação são significativos, com destaque para os postos operativos PO25, PO27 e PO13; c pelo método UEP, os produtos Filé de Peito de Frango e Peito de Frango com Osso atingem uma lucratividade de 34,43% e 25,60%, respectivamente. Conclui-se que o método UEP identifica os custos de transformação e ainda gera informações que dão suporte para melhorias nos processos produtivos. The general objective of this paper is to develop a proposal to implement the Unit Effort of Production (UEP for an aviary agribusiness. To do so, a descriptive research is carried out to approach the problem in a qualitative and quantitative way through a case study. The results show that: a the company has a different production process because its outcome products come from the disassembly of one single raw material, the chickens; b transforming costs are significant, especially with operational posts PO25, PO27 and PO13; c with the UEP method, the Boneless Chicken Breast and Bone-in Chicken Breast products attain a profitability of 34.43% and 25.60%, respectively. It can be concluded that the UEP method identifies the transformation costs as well as generates information to serve as the foundation for improvements in the production processes.

  17. Full Space Vectors Modulation for Nine-Switch Converters Including CF & DF Modes

    DEFF Research Database (Denmark)

    Dehghan Dehnavi, Seyed Mohammad; Mohamadian, Mustafa; Andersen, Michael A. E.

    2010-01-01

    converter. As a space vector modulation for DF mode has already been proposed by authors. This paper proposes a full space vector modulation (SVM) for both CF and DF modes. Also practical methods are presented for SVM proposed. In addition a special SVM is proposed that offers minimum total harmonic...... distortion (THD) in DF mode. The performance of the proposed SVM is verified by simulation results....

  18. Clays as green catalysts in the cholesterol esterification: spectroscopic characterization and polymorphs identification by thermal analysis methods. An interdisciplinary laboratorial proposal for the undergraduate level

    International Nuclear Information System (INIS)

    Maria, Teresa M R.; Nunes, Rui M. D.; Pereira, Mariette M.; Eusebio, M. Ermelinda S.

    2009-01-01

    A laboratory experiment that enables the professor to introduce the problematic of sustainable development in pharmaceutical chemistry to undergraduate students is proposed, using a simple synthetic procedure. Cholesteryl acetate is prepared by the esterification of cholesterol using Montmorillonite K10 as heterogeneous catalyst. Cholesterol and cholesteryl acetate are characterized by spectroscopic ( 1 H RMN, 13 C RMN, FTIR) and thermal analysis techniques. The thermal methods are used to introduce the concepts of polymorphism and the nature of mesophases. (author)

  19. Full page insight

    DEFF Research Database (Denmark)

    Cortsen, Rikke Platz

    2014-01-01

    Alan Moore and his collaborating artists often manipulate time and space by drawing upon the formal elements of comics and making alternative constellations. This article looks at an element that is used frequently in comics of all kinds – the full page – and discusses how it helps shape spatio......, something that it shares with the full page in comics. Through an analysis of several full pages from Moore titles like Swamp Thing, From Hell, Watchmen and Promethea, it is made clear why the full page provides an apt vehicle for an apocalypse in comics....

  20. Settlement behavior of the container for high-level nuclear waste disposal. Centrifuge model tests and proposal for simple evaluation method for settlement behavior

    International Nuclear Information System (INIS)

    Nakamura, Kunihiko; Tanaka, Yukihisa

    2004-01-01

    In Japan, bentonite will be used as buffer materials in high-level nuclear waste disposal. In the softened buffer material with the infiltration of various properties of under ground water, if the container deeply sinks, the decrease of the thickness of the buffer materials may lose the required abilities. Therefore, it is very important to consider settlement of container. In this study, influences of distilled water and artificial seawater on the settlement of the container were investigated and a simple evaluation method for settlement of the container was proposed. The following findings were obtained from this study. (1) Under the distilled water, amount of settlement decreases exponentially as dry density becomes larger. (2) While the amount of settlement of container under the 10% artificial seawater was almost equal to the one in the distilled water, the container was floating under the 100% artificial seawater. (3) The simple evaluation method for settlement of container was proposed based on the diffuse double layer theory, and the effectiveness of the proposed method was demonstrated by the results of several experiments. (author)

  1. Relationship between gastroesophageal reflux disease and Ph nose and salivary: proposal of a simple method outpatient in patients adults.

    Science.gov (United States)

    Caruso, Arturo Armone; Del Prete, Salvatore; Ferrara, Lydia; Serra, Raffaele; Telesca, Donato Alessandro; Ruggiero, Simona; Russo, Teresa; Sivero, Luigi

    2016-01-01

    The frequency of gastroesophageal reflux disease (GERD) is increasing, in part through easy inspection of the upper digestive tract, but especially for a real spread of the disease as a consequence of modernity, lifestyle, incorrect dietary rules, and stress arising from social norms. It is a common chronic gastrointestinal disorder in Europe and the United States. The aim of our study is to highlight a relationship between gastroesophageal reflux disease and salivary pH as evidenced by indicator strips, especially in the outpatient field. Twenty adult subjects (10 males and 10 females) aged between 18 and 50 years (GROUP A)_ were selected. How to control a homogeneous group of 20 patients without GERD, or from any type of allergies (GROUP B) was enlisted. This method has provided excellent results showing no difference in the measured values compared with the traditional instrumental measurement. Our study has allowed us to observe a strong correlation between the saliva pH, nasal cavities and the interaction between the two districts, and could be the basis for a diagnosis of GERD especially in primary health care clinics and in the initial stage of the disease.

  2. Facies Constrained Elastic Full Waveform Inversion

    KAUST Repository

    Zhang, Z.

    2017-05-26

    Current efforts to utilize full waveform inversion (FWI) as a tool beyond acoustic imaging applications, for example for reservoir analysis, face inherent limitations on resolution and also on the potential trade-off between elastic model parameters. Adding rock physics constraints does help to mitigate these issues. However, current approaches to add such constraints are based on averaged type rock physics regularization terms. Since the true earth model consists of different facies, averaging over those facies naturally leads to smoothed models. To overcome this, we propose a novel way to utilize facies based constraints in elastic FWI. A so-called confidence map is calculated and updated at each iteration of the inversion using both the inverted models and the prior information. The numerical example shows that the proposed method can reduce the cross-talks and also can improve the resolution of inverted elastic properties.

  3. Facies Constrained Elastic Full Waveform Inversion

    KAUST Repository

    Zhang, Z.; Zabihi Naeini, E.; Alkhalifah, Tariq Ali

    2017-01-01

    Current efforts to utilize full waveform inversion (FWI) as a tool beyond acoustic imaging applications, for example for reservoir analysis, face inherent limitations on resolution and also on the potential trade-off between elastic model parameters. Adding rock physics constraints does help to mitigate these issues. However, current approaches to add such constraints are based on averaged type rock physics regularization terms. Since the true earth model consists of different facies, averaging over those facies naturally leads to smoothed models. To overcome this, we propose a novel way to utilize facies based constraints in elastic FWI. A so-called confidence map is calculated and updated at each iteration of the inversion using both the inverted models and the prior information. The numerical example shows that the proposed method can reduce the cross-talks and also can improve the resolution of inverted elastic properties.

  4. Trends and regional variations in provision of contraception methods in a commercially insured population in the United States based on nationally proposed measures.

    Science.gov (United States)

    Law, A; Yu, J S; Wang, W; Lin, J; Lynen, R

    2017-09-01

    Three measures to assess the provision of effective contraception methods among reproductive-aged women have recently been endorsed for national public reporting. Based on these measures, this study examined real-world trends and regional variations of contraceptive provision in a commercially insured population in the United States. Women 15-44years old with continuous enrollment in each year from 2005 to 2014 were identified from a commercial claims database. In accordance with the proposed measures, percentages of women (a) provided most effective or moderately effective (MEME) methods of contraception and (b) provided a long-acting reversible contraceptive (LARC) method were calculated in two populations: women at risk for unintended pregnancy and women who had a live birth within 3 and 60days of delivery. During the 10-year period, the percentages of women at risk for unintended pregnancy provided MEME contraceptive methods increased among 15-20-year-olds (24.5%-35.9%) and 21-44-year-olds (26.2%-31.5%), and those provided a LARC method also increased among 15-20-year-olds (0.1%-2.4%) and 21-44-year-olds (0.8%-3.9%). Provision of LARC methods increased most in the North Central and West among both age groups of women. Provision of MEME contraceptives and LARC methods to women who had a live birth within 60days postpartum also increased across age groups and regions. This assessment indicates an overall trend of increasing provision of MEME contraceptive methods in the commercial sector, albeit with age group and regional variations. If implemented, these proposed measures may have impacts on health plan contraceptive access policy. Copyright © 2017 Elsevier Inc. All rights reserved.

  5. Proposal for Testing and Validation of Vacuum Ultra-Violet Atomic Laser-Induced Fluorescence as a Method to Analyze Carbon Grid Erosion in Ion Thrusters

    Science.gov (United States)

    Stevens, Richard

    2003-01-01

    Previous investigation under award NAG3-25 10 sought to determine the best method of LIF to determine the carbon density in a thruster plume. Initial reports from other groups were ambiguous as to the number of carbon clusters that might be present in the plume of a thruster. Carbon clusters would certainly affect the ability to LIF; if they were the dominant species, then perhaps the LIF method should target clusters. The results of quadrupole mass spectroscopy on sputtered carbon determined that minimal numbers of clusters were sputtered from graphite under impact from keV Krypton. There were some investigations in the keV range by other groups that hinted at clusters, but at the time the proposal was presented to NASA, there was no data from low-energy sputtering available. Thus, the proposal sought to develop a method to characterize the population only of atoms sputtered from a graphite target in a test cell. Most of the ground work had been established by the previous two years of investigation. The proposal covering 2003 sought to develop an anti-Stokes Raman shifting cell to generate VUW light and test this cell on two different laser systems, ArF and YAG- pumped dye. The second goal was to measure the lowest detectable amounts of carbon atoms by 156.1 nm and 165.7 nm LIF. If equipment was functioning properly, it was expected that these goals would be met easily during the timeframe of the proposal, and that is the reason only modest funding was requested. The PI was only funded at half- time by Glenn during the summer months. All other work time was paid for by Whitworth College. The college also funded a student, Charles Shawley, who worked on the project during the spring.

  6. Full reflector thickness and isolation thickness on neutron transport

    International Nuclear Information System (INIS)

    Sakai, Tomohiro; Naito, Yoshitaka; Komuro, Yuichi.

    1988-08-01

    A method to determine ''full reflector thickness'' and ''isolation thickness'', which is utilized for criticality safety evaluation on nuclear fuel facilities, was proposed in this paper. Firstly, a calculation was tryed to obtain the two kinds of thicknesses from the result of criticality calculations for a specific case. Then, two simple equations which calculates the two kinds of thicknesses were made from the relation between reflector (or isolator) thickness and k eff , and one-group diffusion theory. Finally, we proposed a new method to determine the thicknesses. From the method we proposed, ''full reflector thickness'' and ''isolation thickness'' can be obtain using the equations and migration length of the reflector (or isolator) and infinite and effective multiplication factor of the fuel. (author)

  7. Full Service Leasing

    OpenAIRE

    Richter, Ján

    2009-01-01

    Aim of this master thesis is to describe the service of Full Service Leasing, as a modern form of financing and management of assets, primarily automobile fleet. Description of full service leasing is designed as a comprehensive and complete guide to support reader's position when deciding to finance and manage a fleet by this service. Whether the reader is an entrepreneur, CFO, fleet manager, new employee of leasing company, or anyone who is interested in this service, this master thesis wil...

  8. Proposal of a simple screening method for a rapid preliminary evaluation of ''heavy metals'' mobility in soils of contaminated sites

    Energy Technology Data Exchange (ETDEWEB)

    Pinto, Valentina; Chiusolo, Francesca; Cremisini, Carlo [ENEA - Italian Agency for New Technologies, Energy and Environment, Rome (Italy). Section PROTCHIM

    2010-09-15

    Risks associated to ''heavy metals'' (HM) soil contamination depend not only on their total content but, mostly, on their mobility. Many extraction procedures have been developed to evaluate HM mobility in contaminated soils, but they are generally time consuming (especially the sequential extraction procedures (SEPs)) and consequently applicable on a limited number of samples. For this reason, a simple screening method, applicable even ''in field'', has been proposed in order to obtain a rapid evaluation of HM mobility in polluted soils, mainly focused on the fraction associated to Fe and Mn oxide/hydroxides. A buffer solution of trisodium citrate and hydroxylamine hydrochloride was used as extractant for a single-step leaching test. The choice of this buffered solution was strictly related to the possibility of directly determining, via titration with dithizone (DZ), the content of Zn, Cu, Pb and Cd, which are among the most representative contaminants in highly mineralised soils. Moreover, the extraction solution is similar, aside from for the pH value, which is the one used in the BCR SEP second step. The analysis of bivalents ions through DZ titration was exploited in order to further simplify and quicken the whole procedure. The proposed method generically measures, in few minutes, the concentration of total extractable ''heavy metals'' expressed as molL{sup -1} without distinguishing between elements. The proposed screening method has been developed and applied on soil samples collected from rural, urban and mining areas, representing different situation of soil contamination. Results were compared with data obtained from the BCR procedure. The screening method demonstrated to be a reliable tool for a rapid evaluation of metals mobility. Therefore, it could be very useful, even ''in field'', both to guide the sampling activity on site and to monitor the efficacy of the subsequent

  9. Emissions trading and competitive positions. The European Proposal for a Directive establishing a Framework for Greenhouse Gas Emissions Trading and Methods for the initial Allocation of Pollution Rights

    International Nuclear Information System (INIS)

    Grimeaud, D.; Peeters, M.

    2002-10-01

    The study on the intention to introduce emissions trading on a European Union level was conducted on the basis of the following three questions: Which methods can be used (by the Member States) to distribute the tradable emissions rights en which legal preconditions should be observed considering the EU-Treaty and the relevant directive proposal? Whenever necessary and possible international agreements on climate change and international trade law will be mentioned. Which safeguards are available for fair competition and which system of emissions trading is advisable in this perspective? How should the PSR (performance standard rate) system, which is preferred by industry, be valued? The structure of this study is as follows: in chapter 2 insight is given into the various methods that can be used to start an emissions trading system, i.e. the way tradable pollution rights are distributed (initial allocation). Chapter 3 will further examine the system of the initial allocation of pollution rights as it has been chosen in the proposal for the European directive. The aim is to give an exact qualification of the method of emissions trading, especially the method of initial allocation, that is used in the directive proposal. Chapter 4 examines whether safeguards are available to prevent competition distortions between firms that fall under the scope of the emissions trading scheme. Special attention will be given to conditions that result from the EU-Treaty in this context, such as the prohibition of state aid. In this chapter the international trade law will be dealt with as well. Chapter 5 will present an executive summary and the specific question whether the PSR-system is legally acceptable or maybe even recommendable, will be answered

  10. Compressive full waveform lidar

    Science.gov (United States)

    Yang, Weiyi; Ke, Jun

    2017-05-01

    To avoid high bandwidth detector, fast speed A/D converter, and large size memory disk, a compressive full waveform LIDAR system, which uses a temporally modulated laser instead of a pulsed laser, is studied in this paper. Full waveform data from NEON (National Ecological Observatory Network) are used. Random binary patterns are used to modulate the source. To achieve 0.15 m ranging resolution, a 100 MSPS A/D converter is assumed to make measurements. SPIRAL algorithm with canonical basis is employed when Poisson noise is considered in the low illuminated condition.

  11. Proposal and field practice of a 'hiyarihatto' activity method for promotion of statements of participants for nuclear power plant organization

    International Nuclear Information System (INIS)

    Aoyagi, Saizo; Fujino, Hidenori; Ishii, Hirotake; Shimoda, Hiroshi; Sakuda, Hiroshi; Yoshikawa, Hidekazu; Sugiman, Toshio

    2011-01-01

    In a 'hiyarihatto' activity, workers report and discuss incident cases related to their work. Such an activity is particularly effective for cultivating participants' attitudes about safety. Nevertheless, a conventional face-to-face hiyarihatto activity includes features that are inappropriate for conduct in a nuclear power plant organization. For example, workers at nuclear power plants are geographically distributed and busy. Therefore, they have great difficulty in participating in a face-to-face hiyarihatto activity. Furthermore, workers' hesitation in discussing problems inhibits the continuation of their active participation. This study is conducted to propose a hiyarihatto activity with an asynchronous and distributed computer-mediated communication (CMC) for a nuclear power plant organization, with the demonstration of its effectiveness through field practice. The proposed method also involves the introduction of special participants who follow action guidelines for the promotion of the continuation of the activity. The method was used in an actual nuclear power plant organization. Results showed that the method is effective under some conditions, such as during periods without facility inspection. Special participants promoted the activity in some cases. Moreover, other factors affecting the activity and some improvements were identified. (author)

  12. Effects of disease severity distribution on the performance of quantitative diagnostic methods and proposal of a novel ‘V-plot’ methodology to display accuracy values

    Science.gov (United States)

    Dehbi, Hakim-Moulay; Howard, James P; Shun-Shin, Matthew J; Sen, Sayan; Nijjer, Sukhjinder S; Mayet, Jamil; Davies, Justin E; Francis, Darrel P

    2018-01-01

    Background Diagnostic accuracy is widely accepted by researchers and clinicians as an optimal expression of a test’s performance. The aim of this study was to evaluate the effects of disease severity distribution on values of diagnostic accuracy as well as propose a sample-independent methodology to calculate and display accuracy of diagnostic tests. Methods and findings We evaluated the diagnostic relationship between two hypothetical methods to measure serum cholesterol (Cholrapid and Cholgold) by generating samples with statistical software and (1) keeping the numerical relationship between methods unchanged and (2) changing the distribution of cholesterol values. Metrics of categorical agreement were calculated (accuracy, sensitivity and specificity). Finally, a novel methodology to display and calculate accuracy values was presented (the V-plot of accuracies). Conclusion No single value of diagnostic accuracy can be used to describe the relationship between tests, as accuracy is a metric heavily affected by the underlying sample distribution. Our novel proposed methodology, the V-plot of accuracies, can be used as a sample-independent measure of a test performance against a reference gold standard. PMID:29387424

  13. Full Length Research Article

    African Journals Online (AJOL)

    Dr Ahmed

    ... Solarin (SWJ):1-6. On Existence Of Control For A Class Of Uncertain Dynamical Systems ... .m We apply the Conjugate Gradient Method. (C.G.M) in ...... Numerical Technique .... Some of its Applications; Journal of Mathematical Analysis and.

  14. Full page fax print

    Indian Academy of Sciences (India)

    user

    While working in the National Chemical Laboratory, Pune, he developed new methods of asymmetric ... He set up a company for custom synthesis and process chemistry (development of chemical .... After World War II, it was replaced by.

  15. Full faith in myself

    Indian Academy of Sciences (India)

    Lawrence

    Full faith in myself. Meenakshi Banerjee. 12. Ihad my schooling at the Irish Convent, Loreto, in Asansol,. West Bengal. Perhaps the earliest memories I have are of myself as a very determined child with a deep appreciation of and inquisitiveness regarding nature although not understanding most of it at that tender age.

  16. Tritium extraction methods proposed for a solid breeder blanket. Subtask WP-B 6.1 of the European Blanket Program 1996

    International Nuclear Information System (INIS)

    Albrecht, H.

    1997-04-01

    Ten different methods for the extraction of tritium from the purge gas of a ceramic blanket are described and evaluated with respect to their applicability for ITER and DEMO. The methods are based on the conditions that the purge gas is composed of helium with an addition of up to 0.1% of H 2 or O 2 and H 2 O to facilitate the release of tritium, and that tritium occurs in the purge gas in two main chemical forms, i.e. HT and HTO. Individual process steps of many methods are identical; in particular, the application of cold traps, molecular sieve beds, and diffusors are proposed in several cases. Differences between the methods arise mainly from the ways in which various process steps are combined and from the operating conditions which are chosen with respect to temperature and pressure. Up to now, none of the methods has been demonstrated to be reliably applicable for the purge gas conditions foreseen for the operation of an ITER blanket test module (or larger ceramic blanket designs such as for DEMO). These conditions are characterized by very high gas flow rates and extremely low concentrations of HT and HTO. Therefore, a proposal has been made (FZK concept) which is expected to have the best potential for applicability to ITER and DEMO and to incorporate the smallest development risk. In this concept, the extraction of tritium and excess hydrogen is accomplished by using a cold trap for freezing out HTO/H 2 O and a 5A molecular sieve bed for the adsorption of HT/H 2 . (orig.) [de

  17. Plate Full of Color

    Centers for Disease Control (CDC) Podcasts

    The Eagle Books are a series of four books that are brought to life by wise animal characters - Mr. Eagle, Miss Rabbit, and Coyote - who engage Rain That Dances and his young friends in the joy of physical activity, eating healthy foods, and learning from their elders about health and diabetes prevention. Plate Full of Color teaches the value of eating a variety of colorful and healthy foods.

  18. Effects of disease severity distribution on the performance of quantitative diagnostic methods and proposal of a novel 'V-plot' methodology to display accuracy values.

    Science.gov (United States)

    Petraco, Ricardo; Dehbi, Hakim-Moulay; Howard, James P; Shun-Shin, Matthew J; Sen, Sayan; Nijjer, Sukhjinder S; Mayet, Jamil; Davies, Justin E; Francis, Darrel P

    2018-01-01

    Diagnostic accuracy is widely accepted by researchers and clinicians as an optimal expression of a test's performance. The aim of this study was to evaluate the effects of disease severity distribution on values of diagnostic accuracy as well as propose a sample-independent methodology to calculate and display accuracy of diagnostic tests. We evaluated the diagnostic relationship between two hypothetical methods to measure serum cholesterol (Chol rapid and Chol gold ) by generating samples with statistical software and (1) keeping the numerical relationship between methods unchanged and (2) changing the distribution of cholesterol values. Metrics of categorical agreement were calculated (accuracy, sensitivity and specificity). Finally, a novel methodology to display and calculate accuracy values was presented (the V-plot of accuracies). No single value of diagnostic accuracy can be used to describe the relationship between tests, as accuracy is a metric heavily affected by the underlying sample distribution. Our novel proposed methodology, the V-plot of accuracies, can be used as a sample-independent measure of a test performance against a reference gold standard.

  19. Plate Full of Color

    Centers for Disease Control (CDC) Podcasts

    2008-08-04

    The Eagle Books are a series of four books that are brought to life by wise animal characters - Mr. Eagle, Miss Rabbit, and Coyote - who engage Rain That Dances and his young friends in the joy of physical activity, eating healthy foods, and learning from their elders about health and diabetes prevention. Plate Full of Color teaches the value of eating a variety of colorful and healthy foods.  Created: 8/4/2008 by National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP).   Date Released: 8/5/2008.

  20. A practical method for determining γ-ray full-energy peak efficiency considering coincidence-summing and self-absorption corrections for the measurement of environmental samples after the Fukushima reactor accident

    Energy Technology Data Exchange (ETDEWEB)

    Shizuma, Kiyoshi, E-mail: shizuma@hiroshima-u.ac.jp [Graduate School of Engineering, Hiroshima University, Higashi-Hiroshima 739-8527 (Japan); Oba, Yurika; Takada, Momo [Graduate School of Integrated Arts and Sciences, Hiroshima University, Higashi-Hiroshima 739-8521 (Japan)

    2016-09-15

    A method for determining the γ-ray full-energy peak efficiency at positions close to three Ge detectors and at the well port of a well-type detector was developed for measuring environmental volume samples containing {sup 137}Cs, {sup 134}Cs and {sup 40}K. The efficiency was estimated by considering two correction factors: coincidence-summing and self-absorption corrections. The coincidence-summing correction for a cascade transition nuclide was estimated by an experimental method involving measuring a sample at the far and close positions of a detector. The derived coincidence-summing correction factors were compared with those of analytical and Monte Carlo simulation methods and good agreements were obtained. Differences in the matrix of the calibration source and the environmental sample resulted in an increase or decrease of the full-energy peak counts due to the self-absorption of γ-rays in the sample. The correction factor was derived as a function of the densities of several matrix materials. The present method was applied to the measurement of environmental samples and also low-level radioactivity measurements of water samples using the well-type detector.

  1. Toward a holistic environmental impact assessment of marble quarrying and processing: proposal of a novel easy-to-use IPAT-based method.

    Science.gov (United States)

    Capitano, Cinzia; Peri, Giorgia; Rizzo, Gianfranco; Ferrante, Patrizia

    2017-03-01

    Marble is a natural dimension stone that is widely used in building due to its resistance and esthetic qualities. Unfortunately, some concerns have arisen regarding its production process because quarrying and processing activities demand significant amounts of energy and greatly affect the environment. Further, performing an environmental analysis of a production process such as that of marble requires the consideration of many environmental aspects (e.g., noise, vibrations, dust and waste production, energy consumption). Unfortunately, the current impact accounting tools do not seem to be capable of considering all of the major aspects of the (marble) production process that may affect the environment and thus cannot provide a comprehensive and concise assessment of all environmental aspects associated with the marble production process. Therefore, innovative, easy, and reliable methods for evaluating its environmental impact are necessary, and they must be accessible for the non-technician. The present study intends to provide a contribution in this sense by proposing a reliable and easy-to-use evaluation method to assess the significance of the environmental impacts associated with the marble production process. In addition, an application of the method to an actual marble-producing company is presented to demonstrate its practicability. Because of its relative ease of use, the method presented here can also be used as a "self-assessment" tool for pursuing a virtuous environmental policy because it enables company owners to easily identify the segments of their production chain that most require environmental enhancement.

  2. Determination of the full energy peak efficiency of NaI(Tl) detectors

    International Nuclear Information System (INIS)

    Cesana, A.; Terrani, M.

    1978-01-01

    A simple procedure for the accurate evaluation of the full energy peak efficiency of NaI(Tl) crystals is described. Particular attention is given to the peak to total ratio determination for which a new method is proposed. (author)

  3. Emptiness and Fullness

    DEFF Research Database (Denmark)

    Bregnbæk, Susanne; Bunkenborg, Mikkel

    As critical voices question the quality, authenticity, and value of people, goods, and words in post-Mao China, accusations of emptiness render things open to new investments of meaning, substance, and value. Exploring the production of lack and desire through fine-grained ethnography, this volume...... examines how diagnoses of emptiness operate in a range of very different domains in contemporary China: In the ostensibly meritocratic exam system and the rhetoric of officials, in underground churches, housing bubbles, and nationalist fantasies, in bodies possessed by spirits and evaluations of jade......, there is a pervasive concern with states of lack and emptiness and the contributions suggest that this play of emptiness and fullness is crucial to ongoing constructions of quality, value, and subjectivity in China....

  4. The Specificity of Observational Studies in Physical Activity and Sports Sciences: Moving Forward in Mixed Methods Research and Proposals for Achieving Quantitative and Qualitative Symmetry

    Directory of Open Access Journals (Sweden)

    M. Teresa Anguera

    2017-12-01

    Full Text Available Mixed methods studies are been increasingly applied to a diversity of fields. In this paper, we discuss the growing use—and enormous potential—of mixed methods research in the field of sport and physical activity. A second aim is to contribute to strengthening the characteristics of mixed methods research by showing how systematic observation offers rigor within a flexible framework that can be applied to a wide range of situations. Observational methodology is characterized by high scientific rigor and flexibility throughout its different stages and allows the objective study of spontaneous behavior in natural settings, with no external influence. Mixed methods researchers need to take bold yet thoughtful decisions regarding both substantive and procedural issues. We present three fundamental and complementary ideas to guide researchers in this respect: we show why studies of sport and physical activity that use a mixed methods research approach should be included in the field of mixed methods research, we highlight the numerous possibilities offered by observational methodology in this field through the transformation of descriptive data into quantifiable code matrices, and we discuss possible solutions for achieving true integration of qualitative and quantitative findings.

  5. Cross-Cultural Adaptation and Validation of the MPAM-R to Brazilian Portuguese and Proposal of a New Method to Calculate Factor Scores

    Science.gov (United States)

    Albuquerque, Maicon R.; Lopes, Mariana C.; de Paula, Jonas J.; Faria, Larissa O.; Pereira, Eveline T.; da Costa, Varley T.

    2017-01-01

    In order to understand the reasons that lead individuals to practice physical activity, researchers developed the Motives for Physical Activity Measure-Revised (MPAM-R) scale. In 2010, a translation of MPAM-R to Portuguese and its validation was performed. However, psychometric measures were not acceptable. In addition, factor scores in some sports psychology scales are calculated by the mean of scores by items of the factor. Nevertheless, it seems appropriate that items with higher factor loadings, extracted by Factor Analysis, have greater weight in the factor score, as items with lower factor loadings have less weight in the factor score. The aims of the present study are to translate, validate the MPAM-R for Portuguese versions, and investigate agreement between two methods used to calculate factor scores. Three hundred volunteers who were involved in physical activity programs for at least 6 months were collected. Confirmatory Factor Analysis of the 30 items indicated that the version did not fit the model. After excluding four items, the final model with 26 items showed acceptable model fit measures by Exploratory Factor Analysis, as well as it conceptually supports the five factors as the original proposal. When two methods are compared to calculate factors scores, our results showed that only “Enjoyment” and “Appearance” factors showed agreement between methods to calculate factor scores. So, the Portuguese version of the MPAM-R can be used in a Brazilian context, and a new proposal for the calculation of the factor score seems to be promising. PMID:28293203

  6. A study on an efficient prediction of welding deformation for T-joint laser welding of sandwich panel Part II: Proposal of a method to use shell element model

    Directory of Open Access Journals (Sweden)

    Jae Woong Kim

    2014-06-01

    Full Text Available I-core sandwich panel that has been used more widely is assembled using high power CO2 laser welding. Kim et al. (2013 proposed a circular cone type heat source model for the T-joint laser welding between face plate and core. It can cover the negative defocus which is commonly adopted in T-joint laser welding to provide deeper penetration. In part I, a volumetric heat source model is proposed and it is verified thorough a comparison of melting zone on the cross section with experiment results. The proposed model can be used for heat transfer analysis and thermal elasto-plastic analysis to predict welding deformation that occurs during laser welding. In terms of computational time, since the thermal elasto-plastic analysis using 3D solid elements is quite time consuming, shell element model with multi-layers have been employed instead. However, the conventional layered approach is not appropriate for the application of heat load at T-Joint. This paper, Part II, suggests a new method to arrange different number of layers for face plate and core in order to impose heat load only to the face plate.

  7. A study on an efficient prediction of welding deformation for T-joint laser welding of sandwich panel Part II : Proposal of a method to use shell element model

    Directory of Open Access Journals (Sweden)

    Kim Jae Woong

    2014-06-01

    Full Text Available I-core sandwich panel that has been used more widely is assembled using high power CO₂laser welding. Kim et al. (2013 proposed a circular cone type heat source model for the T-joint laser welding between face plate and core. It can cover the negative defocus which is commonly adopted in T-joint laser welding to provide deeper penetration. In part I, a volumetric heat source model is proposed and it is verified thorough a comparison of melting zone on the cross section with experiment results. The proposed model can be used for heat transfer analysis and thermal elasto-plastic analysis to predict welding deformation that occurs during laser welding. In terms of computational time, since the thermal elasto-plastic analysis using 3D solid elements is quite time consuming, shell element model with multi-layers have been employed instead. However, the conventional layered approach is not appropriate for the application of heat load at T-Joint. This paper, Part II, suggests a new method to arrange different number of layers for face plate and core in order to impose heat load only to the face plate.

  8. Comparison of a new hydro-surgical technique to traditional methods for the preparation of full-thickness skin grafts from canine cadaveric skin and report of a single clinical case.

    Science.gov (United States)

    Townsend, F I; Ralphs, S C; Coronado, G; Sweet, D C; Ward, J; Bloch, C P

    2012-01-01

    To compare the hydro-surgical technique to traditional techniques for removal of subcutaneous tissue in the preparation of full-thickness skin grafts. Ex vivo experimental study and a single clinical case report. Four canine cadavers and a single clinical case. Four sections of skin were harvested from the lateral flank of recently euthanatized dogs. Traditional preparation methods used included both a blade or scissors technique, each of which were compared to the hydro-surgical technique individually. Preparation methods were compared based on length of time for removal of the subcutaneous tissue from the graft, histologic grading, and measurable thickness as compared to an untreated sample. The hydro-surgical technique had the shortest skin graft preparation time as compared to traditional techniques (p = 0.002). There was no significant difference in the histological grading or measurable subcutaneous thickness between skin specimens. The hydro-surgical technique provides a rapid, effective debridement of subcutaneous tissue in the preparation of full-thickness skin grafts. There were not any significant changes in histological grade and subcutaneous tissue remaining among all treatment types. Additionally the hydro-surgical technique was successfully used to prepare a full-thickness meshed free skin graft in the reconstruction of a traumatic medial tarsal wound in a dog.

  9. Full metal jacket!

    CERN Document Server

    Laëtitia Pedroso

    2011-01-01

    Ten years ago, standard issue clothing only gave CERN firemen partial protection but today our fire-fighters are equipped with state-of-the-art, full personal protective equipment.   CERN's Fire Brigade team. For many years, the members of CERN's Fire Brigade went on call-outs clad in their work trousers and fire-rescue coats, which only afforded them partial protection. Today, textile manufacturing techniques have moved on a long way and CERN's firemen are now kitted out with state-of-the-art personal protective equipment. The coat and trousers are three-layered, comprising fire-resistant aramide, a protective membrane and a thermal lining. The CERN Fire Brigade' new state-of-the-art personal protection equipment. "This equipment is fully compliant with the standards in force and is therefore resistant to cuts, abrasion, electrical arcs with thermal effects and, of course, fire," explains Patrick Berlinghi, the CERN Fire Brigade's Logistics Officer. You might think that su...

  10. Policies for full employment

    DEFF Research Database (Denmark)

    de Koning, Jaap; Layard, Richard; Nickel, Stephen

    European unemployment is too high, and employment is too low. Over 7½ per cent of Europe's workforce is unemployed, and only two thirds of people aged 15-64 are in work. At the Lisbon summit two years ago the heads of government set the target that by 2010 the employment rate should rise from 64...... per cent to at least 70 per cent. And for older workers between 55 and 64 the employment rate should rise from 38 per cent to at least one half. These are ambitious targets. They will require two big changes: more people must seek work, and among those seeking work a higher proportion must get a job....... So we need higher participation, and (for full employment) we need a much lower unemployment rate. Can it be done? A mere glance at the experience of different European countries shows that it can. As Table 1 shows, four E.U. countries already exceed the overall target for 2010 (Britain, Denmark...

  11. The etiologic role of genetic and environmental factors in criminal behavior as determined from full- and half-sibling pairs: an evaluation of the validity of the twin method.

    Science.gov (United States)

    Kendler, K S; Lönn, S L; Maes, H H; Sundquist, J; Sundquist, K

    2015-07-01

    Twin studies have shown that criminal behavior (CB) is influenced by both genetic and shared environmental factors. Could these results be replicated using full-siblings and half-siblings? In 911 009 full-siblings reared together (FSRT), 41 872 half-siblings reared together (HSRT) and 52 590 half-siblings reared apart (HSRA), CB was assessed from the Swedish Crime Register. Modeling, including testing for age differences and rearing status, was performed using the OpenMx package. Five sibling models were fitted examining FSRT and HSRT 0-2 years different in age, and both FSRT and HSRT, and FSRT, HSRT and HSRA 0-10 years different in age with and without a specified shared environment indexing age differences. Heritability estimates for CB ranged from 33 to 55% in females and 39 to 56% in males, similar to those found in our prior twin study on the same population. Estimates for the shared environment varied from 1 to 14% in females and 10 to 23% in males, lower than those estimated in the twin study. The specified shared environment indexed by sibling age differences was significant in all models tested. Heritability estimates for CB from full- and half-siblings closely approximated those found from twins in the same population, validating the twin method. Shared environmental estimates were lower, suggesting the presence of shared environmental factors for CB specific to twins. When rearing status can be assessed, full- and half-siblings offer an additional method for assessing the role of genetic and environmental factors in complex disorders. However, age differences in siblings may need to be included in the models.

  12. Combining the Complete Active Space Self-Consistent Field Method and the Full Configuration Interaction Quantum Monte Carlo within a Super-CI Framework, with Application to Challenging Metal-Porphyrins.

    Science.gov (United States)

    Li Manni, Giovanni; Smart, Simon D; Alavi, Ali

    2016-03-08

    A novel stochastic Complete Active Space Self-Consistent Field (CASSCF) method has been developed and implemented in the Molcas software package. A two-step procedure is used, in which the CAS configuration interaction secular equations are solved stochastically with the Full Configuration Interaction Quantum Monte Carlo (FCIQMC) approach, while orbital rotations are performed using an approximated form of the Super-CI method. This new method does not suffer from the strong combinatorial limitations of standard MCSCF implementations using direct schemes and can handle active spaces well in excess of those accessible to traditional CASSCF approaches. The density matrix formulation of the Super-CI method makes this step independent of the size of the CI expansion, depending exclusively on one- and two-body density matrices with indices restricted to the relatively small number of active orbitals. No sigma vectors need to be stored in memory for the FCIQMC eigensolver--a substantial gain in comparison to implementations using the Davidson method, which require three or more vectors of the size of the CI expansion. Further, no orbital Hessian is computed, circumventing limitations on basis set expansions. Like the parent FCIQMC method, the present technique is scalable on massively parallel architectures. We present in this report the method and its application to the free-base porphyrin, Mg(II) porphyrin, and Fe(II) porphyrin. In the present study, active spaces up to 32 electrons and 29 orbitals in orbital expansions containing up to 916 contracted functions are treated with modest computational resources. Results are quite promising even without accounting for the correlation outside the active space. The systems here presented clearly demonstrate that large CASSCF calculations are possible via FCIQMC-CASSCF without limitations on basis set size.

  13. Oriented Polar Molecules in a Solid Inert-Gas Matrix: A Proposed Method for Measuring the Electric Dipole Moment of the Electron

    Science.gov (United States)

    Vutha, A.; Horbatsch, M.; Hessels, E.

    2018-01-01

    We propose a very sensitive method for measuring the electric dipole moment of the electron using polar molecules embedded in a cryogenic solid matrix of inert-gas atoms. The polar molecules can be oriented in the $\\hat{\\rm{z}}$ direction by an applied electric field, as has recently been demonstrated by Park, et al. [Angewandte Chemie {\\bf 129}, 1066 (2017)]. The trapped molecules are prepared into a state which has its electron spin perpendicular to $\\hat{\\rm{z}}$, and a magnetic field along $\\hat{\\rm{z}}$ causes precession of this spin. An electron electric dipole moment $d_e$ would affect this precession due to the up to 100~GV/cm effective electric field produced by the polar molecule. The large number of polar molecules that can be embedded in a matrix, along with the expected long coherence times for the precession, allows for the possibility of measuring $d_e$ to an accuracy that surpasses current measurements by many orders of magnitude. Because the matrix can inhibit molecular rotations and lock the orientation of the polar molecules, it may not be necessary to have an electric field present during the precession. The proposed technique can be applied using a variety of polar molecules and inert gases, which, along with other experimental variables, should allow for careful study of systematic uncertainties in the measurement.

  14. method

    Directory of Open Access Journals (Sweden)

    L. M. Kimball

    2002-01-01

    Full Text Available This paper presents an interior point algorithm to solve the multiperiod hydrothermal economic dispatch (HTED. The multiperiod HTED is a large scale nonlinear programming problem. Various optimization methods have been applied to the multiperiod HTED, but most neglect important network characteristics or require decomposition into thermal and hydro subproblems. The algorithm described here exploits the special bordered block diagonal structure and sparsity of the Newton system for the first order necessary conditions to result in a fast efficient algorithm that can account for all network aspects. Applying this new algorithm challenges a conventional method for the use of available hydro resources known as the peak shaving heuristic.

  15. Additional comments on 'A proposed method for measuring the electric dipole moment of the neutron using acceleration in an electric field gradient and ultracold neutron interferometry'

    CERN Document Server

    Lamoreaux, S K

    1999-01-01

    We have previously (Lamoreaux and Golub, Los Alamos archive (xxx) nucl-ex/9901007vs, Nucl. Instr. and Meth., 433 (1999)) presented an analysis, using classical, semi-classical and quantum mechanical tehniques, of the proposal of Freedman et al., (Nucl. Instr. and Meth., A 396 (1997) 181) to search for the neutron electric dipole moment by the use of acceleration of ultracold neutrons in an inhomogeneous electric field followed by amplification of the resulting displacement by several methods involving spin independent interactions (gravity) or reflection from curved (spin independent) mirrors. Following the appearance of some more recent comments (Peshkin, Los Alamos archive (xxx) nucl-ex/9903012 v2; Dombeck and Ringo, Nucl. Instr. and Meth., A 433 (1999)) it now seems reasonable to publish a revised version of our quantum mechanical treatment (Section 2 B of ) with a more detailed exposition.

  16. Same day identification and full panel antimicrobial susceptibility testing of bacteria from positive blood culture bottles made possible by a combined lysis-filtration method with MALDI-TOF VITEK mass spectrometry and the VITEK2 system.

    Directory of Open Access Journals (Sweden)

    Alexandra Machen

    Full Text Available Rapid identification and antimicrobial susceptibility testing of microorganisms causing bloodstream infections or sepsis have the potential to improve patient care. This proof-of-principle study evaluates the Lysis-Filtration Method for identification as well as antimicrobial susceptibility testing of bacteria directly from positive blood culture bottles in a clinical setting. A total of 100 non-duplicated positive blood cultures were tested and 1012 microorganism-antimicrobial combinations were assessed. An aliquot of non-charcoal blood culture broth was incubated with lysis buffer briefly before being filtered and washed. Microorganisms recovered from the filter membrane were first identified by using Matrix-Assisted Laser Desorption/Ionization Time-of-Flight VITEK® Mass Spectrometry (VITEK MS. After quick identification from VITEK MS, filtered microorganisms were inoculated to VITEK®2 system for full panel antimicrobial susceptibility testing analysis. Of 100 bottles tested, the VITEK MS resulted in 94.0% correct organism identification to the species level. Compared to the conventional antimicrobial susceptibility testing methods, direct antimicrobial susceptibility testing from VITEK®2 resulted in 93.5% (946/1012 category agreement of antimicrobials tested, with 3.6% (36/1012 minor error, 1.7% (7/1012 major error, and 1.3% (13/1012 very major error of antimicrobials. The average time to identification and antimicrobial susceptibility testing was 11.4 hours by using the Lysis-Filtration method for both VITEK MS and VITEK®2 compared to 56.3 hours by using conventional methods (p<0.00001. Thus, the same-day results of microorganism identification and antimicrobial susceptibility testing directly from positive blood culture can be achieved and can be used for appropriate antibiotic therapy and antibiotic stewardship.

  17. Evaluation of acoustic resonance at branch section in main steam line. Part 2. Proposal of method for predicting resonance frequency in steam flow

    International Nuclear Information System (INIS)

    Uchiyama, Yuta; Morita, Ryo

    2012-01-01

    Flow-induced acoustic resonances of piping system containing closed side-branches are sometimes encountered in power plants. Acoustic standing waves with large amplitude pressure fluctuation in closed side-branches are excited by the unstable shear layer which separates the mean flow in the main piping from the stagnant fluid in the branch. In U.S. NPP, the steam dryer had been damaged by high cycle fatigue due to acoustic-induced vibration under a power uprating condition. Our previous research developed the method for evaluating the acoustic resonance at the branch sections in actual power plants by using CFD. In the method, sound speed in wet steam is evaluated by its theory on the assumption of homogeneous flow, although it may be different from practical sound speed in wet steam. So, it is necessary to consider and introduce the most suitable model of practical sound speed in wet steam. In addition, we tried to develop simplified prediction method of the amplitude and frequency of pressure fluctuation in wet steam flow. Our previous experimental research clarified that resonance amplitude of fluctuating pressure at the top of the branch in wet steam. However, the resonance frequency in steam condition could not be estimated by using theoretical equation as the end correction in steam condition and sound speed in wet steam is not clarified as same reason as CFD. Therefore, in this study, we tried to evaluate the end correction in each dry and wet steam and sound speed of wet steam from experimental results. As a result, method for predicting resonance frequency by using theoretical equation in each wet and dry steam condition was proposed. (author)

  18. Reconfigurable Full-Page Braille Displays

    Science.gov (United States)

    Garner, H. Douglas

    1994-01-01

    Electrically actuated braille display cells of proposed type arrayed together to form full-page braille displays. Like other braille display cells, these provide changeable patterns of bumps driven by digitally recorded text stored on magnetic tapes or in solid-state electronic memories. Proposed cells contain electrorheological fluid. Viscosity of such fluid increases in strong electrostatic field.

  19. Cryptanalysis of the full Spritz stream cipher

    DEFF Research Database (Denmark)

    Banik, Subhadeep; Isobe, Takanori

    2016-01-01

    Spritz is a stream cipher proposed by Rivest and Schuldt at the rump session of CRYPTO 2014. It is intended to be a replacement of the popular RC4 stream cipher. In this paper we propose distinguishing attacks on the full Spritz, based on a short-term bias in the first two bytes of a keystream an...

  20. Effective public involvement in the HoST-D Programme for dementia home care support: From proposal and design to methods of data collection (innovative practice).

    Science.gov (United States)

    Giebel, Clarissa; Roe, Brenda; Hodgson, Anthony; Britt, David; Clarkson, Paul

    2017-01-01

    Public involvement is an important element in health and social care research. However, it is little evaluated in research. This paper discusses the utility and impact of public involvement of carers and people with dementia in a five-year programme on effective home support in dementia, from proposal and design to methods of data collection, and provides a useful guide for future research on how to effectively involve the public. The Home SupporT in Dementia (HoST-D) Programme comprises two elements of public involvement, a small reference group and a virtual lay advisory group. Involving carers and people with dementia is based on the six key values of involvement - respect, support, transparency, responsiveness, fairness of opportunity, and accountability. Carers and people with dementia gave opinions on study information, methods of data collection, an economic model, case vignettes, and a memory aid booklet, which were all taken into account. Public involvement has provided benefits to the programme whilst being considerate of the time constraints and geographical locations of members.

  1. Thesis Proposal

    DEFF Research Database (Denmark)

    Sloth, Erik

    2010-01-01

    Strukturen i Thesis proposal er følgende: Først præsenteres mine konkrete empiriske forskningsprojekter som skal munde ud i afhandlingens artikler. Jeg præsenterer herefter de teoretiske overvejelser omkring oplevelsesbegrebet og forbrugerkulturteori som danner baggrund for at jeg er nået frem til...

  2. A proposal for a test method for assessment of hazard property HP 12 ("Release of an acute toxic gas") in hazardous waste classification - Experience from 49 waste.

    Science.gov (United States)

    Hennebert, Pierre; Samaali, Ismahen; Molina, Pauline

    2016-12-01

    A stepwise method for assessment of the HP 12 is proposed and tested with 49 waste samples. The hazard property HP 12 is defined as "Release of an acute toxic gas": waste which releases acute toxic gases (Acute Tox. 1, 2 or 3) in contact with water or an acid. When a waste contains a substance assigned to one of the following supplemental hazards EUH029, EUH031 and EUH032, it shall be classified as hazardous by HP 12 according to test methods or guidelines (EC, 2014a, 2014b). When the substances with the cited hazard statement codes react with water or an acid, they can release HCl, Cl 2 , HF, HCN, PH 3 , H 2 S, SO 2 (and two other gases very unlikely to be emitted, hydrazoic acid HN 3 and selenium oxide SeO 2 - a solid with low vapor pressure). Hence, a method is proposed:For a set of 49 waste, water addition did not produce gas. Nearly all the solid waste produced a gas in contact with hydrochloric acid in 5 min in an automated calcimeter with a volume >0.1L of gas per kg of waste. Since a plateau of pressure is reached only for half of the samples in 5 min, 6 h trial with calorimetric bombs or glass flasks were done and confirmed the results. Identification of the gases by portable probes showed that most of the tested samples emit mainly CO 2 . Toxic gases are emitted by four waste: metallic dust from the aluminum industry (CO), two air pollution control residue of industrial waste incinerator (H 2 S) and a halogenated solvent (organic volatile(s) compound(s)). HF has not been measured in these trials started before the present definition of HP 12. According to the definition of HP 12, only the H 2 S emission of substances with hazard statement EUH031 is accounted for. In view of the calcium content of the two air pollution control residue, the presence of calcium sulphide (EUH031) can be assumed. These two waste are therefore classified potentially hazardous for HP 12, from a total of 49 waste. They are also classified as hazardous for other properties (HP 7

  3. Method

    Directory of Open Access Journals (Sweden)

    Ling Fiona W.M.

    2017-01-01

    Full Text Available Rapid prototyping of microchannel gain lots of attention from researchers along with the rapid development of microfluidic technology. The conventional methods carried few disadvantages such as high cost, time consuming, required high operating pressure and temperature and involve expertise in operating the equipment. In this work, new method adapting xurography method is introduced to replace the conventional method of fabrication of microchannels. The novelty in this study is replacing the adhesion film with clear plastic film which was used to cut the design of the microchannel as the material is more suitable for fabricating more complex microchannel design. The microchannel was then mold using polymethyldisiloxane (PDMS and bonded with a clean glass to produce a close microchannel. The microchannel produced had a clean edge indicating good master mold was produced using the cutting plotter and the bonding between the PDMS and glass was good where no leakage was observed. The materials used in this method is cheap and the total time consumed is less than 5 hours where this method is suitable for rapid prototyping of microchannel.

  4. Summary Report of Laboratory Testing to Establish the Effectiveness of Proposed Treatment Methods for Unremediated and Remediated Nitrate Salt Waste Streams

    Energy Technology Data Exchange (ETDEWEB)

    Anast, Kurt Roy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Funk, David John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-05-12

    The inadvertent creation of transuranic waste carrying hazardous waste codes D001 and D002 requires the treatment of the material to eliminate the hazardous characteristics and allow its eventual shipment and disposal at the Waste Isolation Pilot Plant (WIPP). This report documents the effectiveness of two treatment methods proposed to stabilize both the unremediated and remediated nitrate salt waste streams (UNS and RNS, respectively). The two technologies include the addition of zeolite (with and without the addition of water as a processing aid) and cementation. Surrogates were developed to evaluate both the solid and liquid fractions expected from parent waste containers, and both the solid and liquid fractions were tested. Both technologies are shown to be effective at eliminating the characteristic of ignitability (D001), and the addition of zeolite was determined to be effective at eliminating corrosivity (D002), with the preferred option1 of zeolite addition currently planned for implementation at the Waste Characterization, Reduction, and Repackaging Facility. During the course of this work, we established the need to evaluate and demonstrate the effectiveness of the proposed remedy for debris material, if required. The evaluation determined that Wypalls absorbed with saturated nitrate salt solutions exhibit the ignitability characteristic (all other expected debris is not classified as ignitable). Follow-on studies will be developed to demonstrate the effectiveness of stabilization for ignitable Wypall debris. Finally, liquid surrogates containing saturated nitrate salts did not exhibit the characteristic of ignitability in their pure form (those neutralized with Kolorsafe and mixed with sWheat did exhibit D001). As a result, additional nitrate salt solutions (those exhibiting the oxidizer characteristic) will be tested to demonstrate the effectiveness of the remedy.

  5. Same Day Identification and Full Panel Antimicrobial Susceptibility Testing of Bacteria from Positive Blood Culture Bottles Made Possible by a Combined Lysis-Filtration Method with MALDI-TOF VITEK Mass Spectrometry and the VITEK2 System

    Science.gov (United States)

    Machen, Alexandra; Drake, Tim; Wang, Yun F. (Wayne)

    2014-01-01

    Rapid identification and antimicrobial susceptibility testing of microorganisms causing bloodstream infections or sepsis have the potential to improve patient care. This proof-of-principle study evaluates the Lysis-Filtration Method for identification as well as antimicrobial susceptibility testing of bacteria directly from positive blood culture bottles in a clinical setting. A total of 100 non-duplicated positive blood cultures were tested and 1012 microorganism-antimicrobial combinations were assessed. An aliquot of non-charcoal blood culture broth was incubated with lysis buffer briefly before being filtered and washed. Microorganisms recovered from the filter membrane were first identified by using Matrix-Assisted Laser Desorption/Ionization Time-of-Flight VITEK® Mass Spectrometry (VITEK MS). After quick identification from VITEK MS, filtered microorganisms were inoculated to VITEK®2 system for full panel antimicrobial susceptibility testing analysis. Of 100 bottles tested, the VITEK MS resulted in 94.0% correct organism identification to the species level. Compared to the conventional antimicrobial susceptibility testing methods, direct antimicrobial susceptibility testing from VITEK®2 resulted in 93.5% (946/1012) category agreement of antimicrobials tested, with 3.6% (36/1012) minor error, 1.7% (7/1012) major error, and 1.3% (13/1012) very major error of antimicrobials. The average time to identification and antimicrobial susceptibility testing was 11.4 hours by using the Lysis-Filtration method for both VITEK MS and VITEK®2 compared to 56.3 hours by using conventional methods (p<0.00001). Thus, the same-day results of microorganism identification and antimicrobial susceptibility testing directly from positive blood culture can be achieved and can be used for appropriate antibiotic therapy and antibiotic stewardship. PMID:24551067

  6. Same day identification and full panel antimicrobial susceptibility testing of bacteria from positive blood culture bottles made possible by a combined lysis-filtration method with MALDI-TOF VITEK mass spectrometry and the VITEK2 system.

    Science.gov (United States)

    Machen, Alexandra; Drake, Tim; Wang, Yun F Wayne

    2014-01-01

    Rapid identification and antimicrobial susceptibility testing of microorganisms causing bloodstream infections or sepsis have the potential to improve patient care. This proof-of-principle study evaluates the Lysis-Filtration Method for identification as well as antimicrobial susceptibility testing of bacteria directly from positive blood culture bottles in a clinical setting. A total of 100 non-duplicated positive blood cultures were tested and 1012 microorganism-antimicrobial combinations were assessed. An aliquot of non-charcoal blood culture broth was incubated with lysis buffer briefly before being filtered and washed. Microorganisms recovered from the filter membrane were first identified by using Matrix-Assisted Laser Desorption/Ionization Time-of-Flight VITEK® Mass Spectrometry (VITEK MS). After quick identification from VITEK MS, filtered microorganisms were inoculated to VITEK®2 system for full panel antimicrobial susceptibility testing analysis. Of 100 bottles tested, the VITEK MS resulted in 94.0% correct organism identification to the species level. Compared to the conventional antimicrobial susceptibility testing methods, direct antimicrobial susceptibility testing from VITEK®2 resulted in 93.5% (946/1012) category agreement of antimicrobials tested, with 3.6% (36/1012) minor error, 1.7% (7/1012) major error, and 1.3% (13/1012) very major error of antimicrobials. The average time to identification and antimicrobial susceptibility testing was 11.4 hours by using the Lysis-Filtration method for both VITEK MS and VITEK®2 compared to 56.3 hours by using conventional methods (pdirectly from positive blood culture can be achieved and can be used for appropriate antibiotic therapy and antibiotic stewardship.

  7. "Epidemiological criminology": coming full circle.

    Science.gov (United States)

    Akers, Timothy A; Lanier, Mark M

    2009-03-01

    Members of the public health and criminal justice disciplines often work with marginalized populations: people at high risk of drug use, health problems, incarceration, and other difficulties. As these fields increasingly overlap, distinctions between them are blurred, as numerous research reports and funding trends document. However, explicit theoretical and methodological linkages between the 2 disciplines remain rare. A new paradigm that links methods and statistical models of public health with those of their criminal justice counterparts is needed, as are increased linkages between epidemiological analogies, theories, and models and the corresponding tools of criminology. We outline disciplinary commonalities and distinctions, present policy examples that integrate similarities, and propose "epidemiological criminology" as a bridging framework.

  8. Nanomaterials, and Occupational Health and Safety—A Literature Review About Control Banding and a Semi-Quantitative Method Proposed for Hazard Assessment.

    Science.gov (United States)

    Dimou, Kaotar; Emond, Claude

    2017-06-01

    approaches that were developed worldwide, and then to suggest an original methodology based on the characterisation of the hazard. For this research, our team conducted a systematic literature review over the past 20 years. This approach is important in understanding the conceptual basis for CB and the model’s overall effectiveness. These considerations will lead to the proposal of an original hazard assessment method based on physico-chemical and biological characteristics. Such a method should help the entire industry better understand the ability of the CB approach to limit workers’ exposure, while identifying the strengths and weaknesses of the approach. Developing this practice method will help to provide relevant recommendations to workers who handle hazardous chemicals such as ENMs and to the general population.

  9. Nanomaterials, and Occupational Health and Safety—A Literature Review About Control Banding and a Semi-Quantitative Method Proposed for Hazard Assessment

    International Nuclear Information System (INIS)

    Dimou, Kaotar; Emond, Claude

    2017-01-01

    approaches that were developed worldwide, and then to suggest an original methodology based on the characterisation of the hazard. For this research, our team conducted a systematic literature review over the past 20 years. This approach is important in understanding the conceptual basis for CB and the model’s overall effectiveness. These considerations will lead to the proposal of an original hazard assessment method based on physico-chemical and biological characteristics. Such a method should help the entire industry better understand the ability of the CB approach to limit workers’ exposure, while identifying the strengths and weaknesses of the approach. Developing this practice method will help to provide relevant recommendations to workers who handle hazardous chemicals such as ENMs and to the general population. (paper)

  10. Accurate Online Full Charge Capacity Modeling of Smartphone Batteries

    OpenAIRE

    Hoque, Mohammad A.; Siekkinen, Matti; Koo, Jonghoe; Tarkoma, Sasu

    2016-01-01

    Full charge capacity (FCC) refers to the amount of energy a battery can hold. It is the fundamental property of smartphone batteries that diminishes as the battery ages and is charged/discharged. We investigate the behavior of smartphone batteries while charging and demonstrate that the battery voltage and charging rate information can together characterize the FCC of a battery. We propose a new method for accurately estimating FCC without exposing low-level system details or introducing new ...

  11. How to identify partial exposures to ionizing radiation? Proposal for a cytogenetic method; Como identificar exposicoes parciais as radiacoes ionizantes? Proposta de um metodo citogenetico

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes, T.S.; Silva, E.B.; Pinto, M.M.P.L.; Amaral, A., E-mail: thiagosalazar@hotmail.com [Universidade Federal de Pernambuco (LAMBDA/UFPE), Recife, PE (Brazil). Departamento de Energia Nuclear. Lab. de Modelagem e Biodosimetria Aplicada; Lloyd, David [Health Protection Agency, Oxford (United Kingdom). Radiation Protection Division

    2013-08-15

    In cases of radiological incidents or in occupational exposures to ionizing radiation, the majority of exposures are not related to the total body, but only partial. In this context, if the cytogenetic dosimetry is performed, there will be an underestimation of the absorbed dose due to the dilution of irradiated cells with non-irradiated cells. Considering the norms of NR 32 - Safety and Health in the Work of Health Service - which recommends cytogenetic dosimetry in the investigation of accidental exposures to ionizing radiations, it is necessary to develop of a tool to provide a better identification of partial exposures. With this aim, a partial body exposure was simulated by mixing, in vitro, 70% of blood irradiated with 4 Gy of X-rays with 30% of unirradiated blood from the same healthy donor. Aliquots of this mixture were cultured for 48 and 72 hours. Prolonging the time of cell culture from 48 to 72 hours produced no significant change in the yield of dicentrics. However, when only M1 (first division cells) were analyzed, the frequency of dicentrics per cell was increased. Prolonging the time of cell culture allowed cells in mitotic delay by irradiation to reach metaphase, and thus provides enough time for the damage to be visualized. The results of this research present the proposed method as an important tool in the investigation of exposed individuals, allowing associating the cytogenetic analysis with the real percentage of irradiated cells, contributing significantly for the decision making in terms of occupational health. (author)

  12. A proposal for evaluation method of crack growth due to cyclic overload for piping materials based on an elastic-plastic fracture mechanics parameter

    International Nuclear Information System (INIS)

    Yamaguchi, Yoshihito; Katsuyama, Jinya; Onizawa, Kunio; Li, Yinsheng; Sugino, Hideharu

    2011-01-01

    The magnitude of Niigata-ken Chuetsu-Oki earthquake in 2007 was beyond the assumed one provided in seismic design. Therefore it becomes an important issue to evaluate the crack growth behaviors due to the cyclic overload like large earthquake. Fatigue crack growth is usually evaluated by Paris's law using the range of stress intensity factor (ΔK). However, ΔK is inappropriate in a loading condition beyond small scale yielding. In this study, the crack growth behaviors for piping materials were investigated based on an elastic-plastic fracture mechanics parameter, J-integral. It was indicated that the crack growth due to the cyclic overload beyond small scale yielding could be the sum of fatigue and ductile crack growth. The retardation effect of excessive loading on the crack growth was observed after the loading. The modified Wheeler model using J-integral has been proposed for the prediction of retardation effect. Finally, an evaluation method for crack growth behaviors due to the cyclic overload is suggested. (author)

  13. Engineering Evaluation of Proposed Alternative Salt Transfer Method for the Molten Salt Reactor Experiment for the Oak Ridge National Laboratory, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    Carlberg, Jon A.; Roberts, Kenneth T.; Kollie, Thomas G.; Little, Leslie E.; Brady, Sherman D.

    2009-01-01

    This evaluation was performed by Pro2Serve in accordance with the Technical Specification for an Engineering Evaluation of the Proposed Alternative Salt Transfer Method for the Molten Salt Reactor Experiment at the Oak Ridge National Laboratory (BJC 2009b). The evaluators reviewed the Engineering Evaluation Work Plan for Molten Salt Reactor Experiment Residual Salt Removal, Oak Ridge National Laboratory, Oak Ridge, Tennessee (DOE 2008). The Work Plan (DOE 2008) involves installing a salt transfer probe and new drain line into the Fuel Drain Tanks and Fuel Flush Tank and connecting them to the new salt transfer line at the drain tank cell shield. The probe is to be inserted through the tank ball valve and the molten salt to the bottom of the tank. The tank would then be pressurized through the Reactive Gas Removal System to force the salt into the salt canisters. The Evaluation Team reviewed the work plan, interviewed site personnel, reviewed numerous documents on the Molten Salt Reactor (Sects. 7 and 8), and inspected the probes planned to be used for the transfer. Based on several concerns identified during this review, the team recommends not proceeding with the salt transfer via the proposed alternate salt transfer method. The major concerns identified during this evaluation are: (1) Structural integrity of the tanks - The main concern is with the corrosion that occurred during the fluorination phase of the uranium removal process. This may also apply to the salt transfer line for the Fuel Flush Tank. Corrosion Associated with Fluorination in the Oak Ridge National Laboratory Fluoride Volatility Process (Litman 1961) shows that this problem is significant. (2) Continued generation of Fluorine - Although the generation of Fluorine will be at a lower rate than experienced before the uranium removal, it will continue to be generated. This needs to be taken into consideration regardless of what actions are taken with the salt. (3) More than one phase of material

  14. Summary Report of Comprehensive Laboratory Testing to Establish the Effectiveness of Proposed Treatment Methods for Unremediated and Remediated Nitrate Salt Waste Streams

    Energy Technology Data Exchange (ETDEWEB)

    Anast, Kurt Roy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Funk, David John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hargis, Kenneth Marshall [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-10-04

    The inadvertent creation of transuranic waste carrying hazardous waste codes D001 and D002 requires the treatment of the material to eliminate the hazardous characteristics and allow its eventual shipment and disposal at the Waste Isolation Pilot Plant (WIPP). This report documents the effectiveness of two treatment methods proposed to stabilize both the unremediated and remediated nitrate salt waste streams (UNS and RNS, respectively) at Los Alamos National Laboratory (LANL). The two technologies include the addition of zeolite (with and without the addition of water as a processing aid) and cementation. Surrogates were developed to evaluate both the solid and liquid fractions expected from parent waste containers, and both the solid and liquid fractions were tested. Both technologies are shown to be effective at eliminating the characteristic of ignitability (D001), and the addition of zeolite was determined to be effective at eliminating corrosivity (D002), with the preferred option1 of adding zeolite currently planned for implementation at LANL’s Waste Characterization, Reduction, and Repackaging Facility (WCRRF). The course of this work verified the need to evaluate and demonstrate the effectiveness of the proposed remedy for debris material, if required. The evaluation determined that WypAlls, cheesecloth, and Celotex absorbed with saturated nitrate salt solutions exhibit the ignitability characteristic (all other expected debris is not classified as ignitable). Finally, liquid surrogates containing saturated nitrate salts did not exhibit the characteristic of ignitability in their pure form (those neutralized with Kolorsafe and mixed with sWheat did exhibit D001). Sensitivity testing and an analysis were conducted to evaluate the waste form for reactivity. Tests included subjecting surrogate material to mechanical impact, friction, electrostatic discharge and thermal insults. The testing confirmed that the waste does not exhibit the characteristic of

  15. Full traveltime inversion in source domain

    KAUST Repository

    Liu, Lu; Guo, Bowen; Luo, Yi

    2017-01-01

    This paper presents a new method of source-domain full traveltime inversion (FTI). The objective of this study is automatically building near-surface velocity using the early arrivals of seismic data. This method can generate the inverted velocity

  16. A Training Program to Enhance Postgraduate Students' Research Skills in Preparing a Research Proposal in the Field of Curriculum and Instruction Methods of Arabic Language

    Science.gov (United States)

    Alfakih, Ahmed Hassan

    2017-01-01

    The study examined the impact of a training program on enhancing postgraduate students' research skills in preparing a research proposal. The nature of the skills required to prepare a research proposal were first determined using a questionnaire. A training program for improving such skills was then constructed and seven postgraduate students in…

  17. Workflows for Full Waveform Inversions

    Science.gov (United States)

    Boehm, Christian; Krischer, Lion; Afanasiev, Michael; van Driel, Martin; May, Dave A.; Rietmann, Max; Fichtner, Andreas

    2017-04-01

    Despite many theoretical advances and the increasing availability of high-performance computing clusters, full seismic waveform inversions still face considerable challenges regarding data and workflow management. While the community has access to solvers which can harness modern heterogeneous computing architectures, the computational bottleneck has fallen to these often manpower-bounded issues that need to be overcome to facilitate further progress. Modern inversions involve huge amounts of data and require a tight integration between numerical PDE solvers, data acquisition and processing systems, nonlinear optimization libraries, and job orchestration frameworks. To this end we created a set of libraries and applications revolving around Salvus (http://salvus.io), a novel software package designed to solve large-scale full waveform inverse problems. This presentation focuses on solving passive source seismic full waveform inversions from local to global scales with Salvus. We discuss (i) design choices for the aforementioned components required for full waveform modeling and inversion, (ii) their implementation in the Salvus framework, and (iii) how it is all tied together by a usable workflow system. We combine state-of-the-art algorithms ranging from high-order finite-element solutions of the wave equation to quasi-Newton optimization algorithms using trust-region methods that can handle inexact derivatives. All is steered by an automated interactive graph-based workflow framework capable of orchestrating all necessary pieces. This naturally facilitates the creation of new Earth models and hopefully sparks new scientific insights. Additionally, and even more importantly, it enhances reproducibility and reliability of the final results.

  18. Review Document: Full Software Trigger

    CERN Document Server

    Albrecht, J; Raven, G

    2014-01-01

    This document presents a trigger system for the upgraded LHCb detector, scheduled to begin operation in 2020. This document serves as input for the internal review towards the "DAQ, online and trigger TDR". The proposed trigger system is implemented entirely in software. In this document we show that track reconstruction of a similar quality to that available in the offline algorithms can be performed on the full inelastic $pp$-collision rate, without prior event selections implemented in custom hardware and without relying upon a partial event reconstruction. A track nding eciency of 98.8 % relative to oine can be achieved for tracks with $p_T >$ 500 MeV/$c$. The CPU time required for this reconstruction is about 40 % of the available budget. Proof-of-principle selections are presented which demonstrate that excellent performance is achievable using an inclusive beauty trigger, in addition to exclusive beauty and charm triggers. Finally, it is shown that exclusive beauty and charm selections that do not intr...

  19. Proposal of method for quantifying uranium weight in the interior of gas centrifuge, and performance evaluation of IF7 treatment reaction product separation and refinement

    International Nuclear Information System (INIS)

    Ema, Akira; Kado, Kazumi; Suzuki, Kazuhiko

    2011-01-01

    In uranium enrichment plant decommissioning, it is important to treat and dispose the gas centrifuge reasonably. At the Ningyo-Toge Environmental Engineering Center of JAEA, it has been planned to carry out IF 7 treatment for the gas centrifuge in the uranium enrichment plant for decontamination before dismantling. In order to carry out this IF 7 treatment, a nondestructive measurement technology to estimate the uranium weight in the interior of the gas centrifuge was needed. However, it was difficult to estimate exactly uranium weight using former methods. Therefore, in this study, we investigated a new nondestructive measurement. As a result, we succeeded in constructing theoretically the methodology using γ-ray intensity measured outside the gas centrifuge and MCNP code. Furthermore, the UF 6 and IF 5 mixture was recovered by IF 7 treatment. A technology to separate and refine IF 5 from this mixture was needed in order to use as a material of IF 7 gas. Therefore, in this study, we carried out IF 5 separation and refinement examination. This paper shows the investigation result of reasonable separation condition and the full-scale examination result. As a result, it could be proved that 86% of IF 5 was separated and refined from UF 6 and IF 5 mixture. (author)

  20. Proposed Method for Disaggregation of Secondary Data: The Model for External Reliance of Localities in the Coastal Management Zone (MERLIN-CMZ)

    Science.gov (United States)

    The Model for External Reliance of Localities In (MERLIN) Coastal Management Zones is a proposed solution to allow scaling of variables to smaller, nested geographies. Utilizing a Principal Components Analysis and data normalization techniques, smaller scale trends are linked to ...

  1. Skin cancer full-grown from scar

    International Nuclear Information System (INIS)

    Zikiryakhodjaev, D.Z.; Sanginov, D.R.

    2001-01-01

    In this chapter authors investigate the peculiarities of skin cancer full-grown from scar, the theory of it's descent, quote some statistical data on skin cancer full-grown from scar and variety clinical forms of skin cancer full-grown from scar was shown, quote some methods of treatment

  2. Semi-Automatic Measurement of the Airway Dimension by Computed Tomography Using the Full-With-Half- Maximum Method: a Study of the Measurement Accuracy according to the Orientation of an Artificial Airway

    International Nuclear Information System (INIS)

    Kim, Nam Kug; Seo, Joon Beom; Song, Koun Sik; Chae, Eun Jin; Kang, Suk Ho

    2008-01-01

    To develop an algorithm to measure the dimensions of an airway oriented obliquely on a volumetric CT, as well as assess the effect of the imaging parameters on the correct measurement of the airway dimension. An airway phantom with 11 poly-acryl tubes of various lumen diameters and wall thicknesses was scanned using a 16-MDCT (multidetector CT) at various tilt angles (0, 30, 45, and 60 ). The CT images were reconstructed at various reconstruction kernels and thicknesses. The axis of each airway was determined using the 3D thinning algorithm, with images perpendicular to the axis being reconstructed. The luminal radius and wall thickness was measured by the full-width-half-maximum method. The influence of the CT parameters (the size of the airways, obliquity on the radius and wall thickness) was assessed by comparing the actual dimension of each tube with the estimated values. The 3D thinning algorithm correctly determined the axis of the oblique airway in all tubes (mean error: 0.91 ± 0.82 .deg. ). A sharper reconstruction kernel, thicker image thickness and larger tilt angle of the airway axis resulted in a significant decrease of the measured wall thickness and an increase of the measured luminal radius. Use of a standard kernel and a 0.75-mm slice thickness resulted in the most accurate measurement of airway dimension, which was independent of obliquity. The airway obliquity and imaging parameters have a strong influence on the accuracy of the airway wall measurement. For the accurate measurement of airway thickness, the CT images should be reconstructed with a standard kernel and a 0.75 mm slice thickness

  3. Effects of pore forming agents of potassium bicarbonate and drug loading method against dissolution mechanisms of amoxicillin drugs encapsulated in hydrogel full-Ipn chitosan-poly(N-vinylcaprolactam) as a floating drug delivery system

    Science.gov (United States)

    Aini, Nurul; Rahayu, Dyah Utami Cahyaning; Budianto, Emil

    2018-04-01

    The limitation of amoxicillin trihydrate in the treatment of H. pylori bacteria is relatively short retention time in the stomach. The FDDS (Floating Drug Delivery System) amoxicillin trihydrate into a chitosan-poly(N-vinylcaprolactam) full-Ipn hydrogel matrix using a pore-forming agent KHCO3 is expected to overcome these limitations. The pore-forming agent to be used is 15% KHCO3 compound. Chemical kinetics approach is performed to determine the dissolution mechanism of amoxicillin trihydrate from K-PNVCL hydrogel in vitro on gastric pH and characterization using SEM performed to confirm the dissolution mechanism. Hydrogels with the addition of pore-forming agents will be loading in situ loading and post loading. Fourier Transform Infra Red (FTIR) spectroscopy was used to characterize K-PNVCL and UV-Vis hydrogels used to calculate the efficiency of encapsulation and drug dissolution rate in K-PNVCL hydrogel. Hydrogel K-PNVCL / KHCO3 that encapsulated by in situ loading method resulted in an encapsulation efficiency of 93.5% and dissolution of 93.4%. While the Hydrogel K-PNVCL / KHCO3 which is drug encapsulation resulted in an encapsulation efficiency of 87.2% with dissolution of 81.5%. Chemical kinetics approach to in situ encapsulation of loading and post loading shows the dissolution mechanism occurring in the K-PNVCL / KHCO3 hydrogel matrix occurs by diffusion. Observation using optical microscope and SEM showed the mechanism of drug dissolution in Hydrogel K-PNVCL occurred by diffusion.

  4. Ultra low power full adder topologies

    DEFF Research Database (Denmark)

    Moradi, Farshad; Wisland, Dag T.; Mahmoodi, Hamid

    In this paper several low power full adder topologies are presented. The main idea of these circuits is based on the sense energy recovery full adder (SERF) design and the GDI (gate diffusion input) technique. These subthreshold circuits are employed for ultra low power applications. While the pr...... the proposed circuits have some area overhead that is negligible, they have at least 62% less power dissipation when compared with existing designs. In this paper, 65 nm standard models are used for simulations....

  5. A hardenability test proposal

    Energy Technology Data Exchange (ETDEWEB)

    Murthy, N.V.S.N. [Ingersoll-Rand (I) Ltd., Bangalore (India)

    1996-12-31

    A new approach for hardenability evaluation and its application to heat treatable steels will be discussed. This will include an overview and deficiencies of the current methods and discussion on the necessity for a new approach. Hardenability terminology will be expanded to avoid ambiguity and over-simplification as encountered with the current system. A new hardenability definition is proposed. Hardenability specification methods are simplified and rationalized. The new hardenability evaluation system proposed here utilizes a test specimen with varying diameter as an alternative to the cylindrical Jominy hardenability test specimen and is readily applicable to the evaluation of a wide variety of steels with different cross-section sizes.

  6. Source Estimation by Full Wave Form Inversion

    Energy Technology Data Exchange (ETDEWEB)

    Sjögreen, Björn [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). Center for Applied Scientific Computing; Petersson, N. Anders [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). Center for Applied Scientific Computing

    2013-08-07

    Given time-dependent ground motion recordings at a number of receiver stations, we solve the inverse problem for estimating the parameters of the seismic source. The source is modeled as a point moment tensor source, characterized by its location, moment tensor components, the start time, and frequency parameter (rise time) of its source time function. In total, there are 11 unknown parameters. We use a non-linear conjugate gradient algorithm to minimize the full waveform misfit between observed and computed ground motions at the receiver stations. An important underlying assumption of the minimization problem is that the wave propagation is accurately described by the elastic wave equation in a heterogeneous isotropic material. We use a fourth order accurate finite difference method, developed in [12], to evolve the waves forwards in time. The adjoint wave equation corresponding to the discretized elastic wave equation is used to compute the gradient of the misfit, which is needed by the non-linear conjugated minimization algorithm. A new source point moment source discretization is derived that guarantees that the Hessian of the misfit is a continuous function of the source location. An efficient approach for calculating the Hessian is also presented. We show how the Hessian can be used to scale the problem to improve the convergence of the non-linear conjugated gradient algorithm. Numerical experiments are presented for estimating the source parameters from synthetic data in a layer over half-space problem (LOH.1), illustrating rapid convergence of the proposed approach.

  7. Full Waveform Inversion Using Nonlinearly Smoothed Wavefields

    KAUST Repository

    Li, Y.; Choi, Yun Seok; Alkhalifah, Tariq Ali; Li, Z.

    2017-01-01

    The lack of low frequency information in the acquired data makes full waveform inversion (FWI) conditionally converge to the accurate solution. An initial velocity model that results in data with events within a half cycle of their location in the observed data was required to converge. The multiplication of wavefields with slightly different frequencies generates artificial low frequency components. This can be effectively utilized by multiplying the wavefield with itself, which is nonlinear operation, followed by a smoothing operator to extract the artificially produced low frequency information. We construct the objective function using the nonlinearly smoothed wavefields with a global-correlation norm to properly handle the energy imbalance in the nonlinearly smoothed wavefield. Similar to the multi-scale strategy, we progressively reduce the smoothing width applied to the multiplied wavefield to welcome higher resolution. We calculate the gradient of the objective function using the adjoint-state technique, which is similar to the conventional FWI except for the adjoint source. Examples on the Marmousi 2 model demonstrate the feasibility of the proposed FWI method to mitigate the cycle-skipping problem in the case of a lack of low frequency information.

  8. Full Waveform Inversion Using Nonlinearly Smoothed Wavefields

    KAUST Repository

    Li, Y.

    2017-05-26

    The lack of low frequency information in the acquired data makes full waveform inversion (FWI) conditionally converge to the accurate solution. An initial velocity model that results in data with events within a half cycle of their location in the observed data was required to converge. The multiplication of wavefields with slightly different frequencies generates artificial low frequency components. This can be effectively utilized by multiplying the wavefield with itself, which is nonlinear operation, followed by a smoothing operator to extract the artificially produced low frequency information. We construct the objective function using the nonlinearly smoothed wavefields with a global-correlation norm to properly handle the energy imbalance in the nonlinearly smoothed wavefield. Similar to the multi-scale strategy, we progressively reduce the smoothing width applied to the multiplied wavefield to welcome higher resolution. We calculate the gradient of the objective function using the adjoint-state technique, which is similar to the conventional FWI except for the adjoint source. Examples on the Marmousi 2 model demonstrate the feasibility of the proposed FWI method to mitigate the cycle-skipping problem in the case of a lack of low frequency information.

  9. Full-scope training simulators

    International Nuclear Information System (INIS)

    Ugedo, E.

    1986-01-01

    The following topics to be covered in this report are: Reasons justifying the use of full-scope simulators for operator qualification. Full-scope simulator description: the control room, the physical models, the computer complex, the instructor's console. Main features of full-scope simulators. Merits of simulator training. The role of full-scope simulators in the training programs. The process of ordering and acquiring a full-scope simulator. Maintaining and updating simulator capabilities. (orig./GL)

  10. A critical examination of some of the field indicators that have been proposed in connection with sound power determination using the intensity method

    DEFF Research Database (Denmark)

    Jacobsen, Finn

    1996-01-01

    A considerable number of 'field indicators' or 'quality indicators' have been proposed in connection with sound power determination based on measurement of intensity. For example, the ISO 9614-1 standard prescribes the use four indicators, and in the North American ANSI S12.12 standard no less th...

  11. Full Employment in Industrialized Countries.

    Science.gov (United States)

    Britton, Andrew

    1997-01-01

    Argues that full employment must be acceptable on both social and economic grounds. Examines profound changes in industrialized economies since the 1970s and the diversity of employment contracts. Suggests that difficult policy decisions surround full employment. (SK)

  12. Development of resilience evaluation method for nuclear power plant. Part 1. Proposal of resilience index for assessment of safety of nuclear power plant under severe accident

    International Nuclear Information System (INIS)

    Demachi, Kazuyuki; Suzuki, Masaaki; Itoi, Tatsuya

    2016-01-01

    In this research, a new index 'The Resilience Index' was proposed to evaluate the capability of nuclear power plant to recover from the situation of safety function lost. Three elements assumed to evaluate the resilience index are the achievement rate, necessary time, and probability of success of each accident management activity. The resilience index is expected to visualize the improvement of safety of each nuclear power plant against severe accidents. (author)

  13. MSR - SPHINX concept program Eros (Experimental zero power Salt reactor SR-0) - The proposed experimental program as a basis for validation of reactor physics methods

    Energy Technology Data Exchange (ETDEWEB)

    Hron, M.; Juricek, V.; Kyncl, J.; Mikisek, M.; Rypar, V. [Nuclear Research Institute Rez plc, Rez (Czech Republic)

    2007-07-01

    The Molten Salt Reactor (MSR) - SPHINX (SPent Hot fuel Incinerator by Neutron fluX) concept solves this principal problem of spent fuel treatment by means of so-called nuclear incineration. It means the burning of fissionable part of its inventory and transmutation of other problematic radionuclides by use of nuclear reactions with neutrons in a MSR-SPHINX system. This reactor system is an actinide burner (most in resonance neutron spectrum) and a radionuclide transmuter in a well-thermalized neutron spectrum. In the frame of the physical part, there are computational analyses and experimental activities. The experimental program has been focused, in its first stage, on a short-term irradiation of small size samples of molten-salt systems as well as structural materials proposed for the MSR blanket in the field of high neutron flux of research reactors. The proposed next stage of the program will focus on a large-scale experimental verification of design inputs by use of MSR-type inserting zones into the existing light water moderated experimental reactor LR-0, which may allow us to modify it into the experimental zero power salt reactor SR-0. There will be a detail description of the proposed program given in the paper together with the so far performed experiments and their first results. These realized experiments help us also to verify computational codes used, and to recognize some anomalies related to molten fluorides utilization. (authors)

  14. Research and development on groundwater dating. Part 11. The proposal of separation method of chloride and sulfate ion for accurate measurement of 36Cl/Cl

    International Nuclear Information System (INIS)

    Nakata, Kotaro; Hasegawa, Takuma

    2010-01-01

    36 Cl is one of the most powerful tools to estimate the residence time of groundwater about 300-1800 thousand years. AMS(Accelerator Mass Spectroscopy) can provide accurate estimation of 36 Cl. However, estimation of 36 Cl by AMS is usually disturbed by isobar such as 36 S. Thus, separation of Cl (usually Cl - form in groundwater) and S (usually SO 4 -2 form in groundwater) is required for accurate estimation of 36 Cl. In previous studies, a methodology (BaSO 4 Method) that uses the difference in solubility between BaSO 4 and BaCl 2 , had been applied as pretreatment method for 36 Cl estimation by AMS. However BaSO 4 Method has following disadvantages; (1) Cl and SO 4 can not be separated completely, (2) accuracy of separation depends on the skills of operator, (3) it takes a long time for treatment, (4) it can not be applied to dilute solutions. Therefore, new methodology that can overcome disadvantages of BaSO 4 method is required for more accurate estimation of 36 Cl. In this study, Column Method based on column chromatography was investigated for pretreatment method for 36 Cl estimation by AMS to separate Cl and SO 4 ions. The conditions for Column Method were determined and adjusted so that Cl and SO 4 ions were separated completely and sufficient amount of Cl for 36 Cl estimation can be treated. The results of AMS measurement showed Column Method can remove SO 4 from Cl more effectively comparing with BaSO 4 method. Furthermore, Column Method was found to have following advantages over BaSO 4 Method; (1) dependence of accuracy of separation on the skills of operator is quite low, (2) treatment can be done within 6 h, (3) it can be applied to dilute solutions. (author)

  15. Missing data methods for dealing with missing items in quality of life questionnaires. A comparison by simulation of personal mean score, full information maximum likelihood, multiple imputation, and hot deck techniques applied to the SF-36 in the French 2003 decennial health survey.

    Science.gov (United States)

    Peyre, Hugo; Leplège, Alain; Coste, Joël

    2011-03-01

    Missing items are common in quality of life (QoL) questionnaires and present a challenge for research in this field. It remains unclear which of the various methods proposed to deal with missing data performs best in this context. We compared personal mean score, full information maximum likelihood, multiple imputation, and hot deck techniques using various realistic simulation scenarios of item missingness in QoL questionnaires constructed within the framework of classical test theory. Samples of 300 and 1,000 subjects were randomly drawn from the 2003 INSEE Decennial Health Survey (of 23,018 subjects representative of the French population and having completed the SF-36) and various patterns of missing data were generated according to three different item non-response rates (3, 6, and 9%) and three types of missing data (Little and Rubin's "missing completely at random," "missing at random," and "missing not at random"). The missing data methods were evaluated in terms of accuracy and precision for the analysis of one descriptive and one association parameter for three different scales of the SF-36. For all item non-response rates and types of missing data, multiple imputation and full information maximum likelihood appeared superior to the personal mean score and especially to hot deck in terms of accuracy and precision; however, the use of personal mean score was associated with insignificant bias (relative bias personal mean score appears nonetheless appropriate for dealing with items missing from completed SF-36 questionnaires in most situations of routine use. These results can reasonably be extended to other questionnaires constructed according to classical test theory.

  16. Improved Object Proposals with Geometrical Features for Autonomous Driving

    Directory of Open Access Journals (Sweden)

    Yiliu Feng

    2017-01-01

    Full Text Available This paper aims at generating high-quality object proposals for object detection in autonomous driving. Most existing proposal generation methods are designed for the general object detection, which may not perform well in a particular scene. We propose several geometrical features suited for autonomous driving and integrate them into state-of-the-art general proposal generation methods. In particular, we formulate the integration as a feature fusion problem by fusing the geometrical features with existing proposal generation methods in a Bayesian framework. Experiments on the challenging KITTI benchmark demonstrate that our approach improves the existing methods significantly. Combined with a convolutional neural net detector, our approach achieves state-of-the-art performance on all three KITTI object classes.

  17. The Weaknesses of Full-Text Searching

    Science.gov (United States)

    Beall, Jeffrey

    2008-01-01

    This paper provides a theoretical critique of the deficiencies of full-text searching in academic library databases. Because full-text searching relies on matching words in a search query with words in online resources, it is an inefficient method of finding information in a database. This matching fails to retrieve synonyms, and it also retrieves…

  18. How Full is Full Employment? : How Tools and Not Theory Explained Full Employment

    NARCIS (Netherlands)

    Rodenburg, P.

    2016-01-01

    The post-war debate on full employment policy was blurred and unclear since the concept of full employment itself was theoretically unclear and un-operational. Unable to theoretically determine the unemployment level of full employment, economists tried to find more empirically based ways to

  19. A novel electrostatic ion-energy spectrometer by the use of a proposed ``self-collection'' method for secondary-electron emission from a metal collector

    Science.gov (United States)

    Hirata, M.; Nagashima, S.; Cho, T.; Kohagura, J.; Yoshida, M.; Ito, H.; Numakura, T.; Minami, R.; Kondoh, T.; Nakashima, Y.; Yatsu, K.; Miyoshi, S.

    2003-03-01

    For the purpose of end-loss-ion energy analyses in open-field plasmas, a newly developed electrostatic ion-energy spectrometer is proposed on the basis of a "self-collection" principle for secondary-electron emission from a metal collector. The ion-energy spectrometer is designed with multiple grids for analyzing incident ion energies, and a set of parallelly placed metal plates with respect to lines of ambient magnetic forces in an open-ended device. One of the most important characteristic properties of this spectrometer is the use of our proposed principle of a "self-collection" mechanism due to E×B drifts for secondary electrons emitted from the grounded metal-plate collector by the use of no further additional magnetic systems except the ambient open-ended fields B. The proof-of-principle and characterization experiments are carried out by the use of a test-ion-beam line along with an additional use of a Helmholtz coil system for the formation of open magnetic fields similar to those in the GAMMA 10 end region. The applications of the developed ion-energy spectrometer for end-loss-ion diagnostics in the GAMMA 10 plasma experiments are demonstrated under the conditions with simultaneous incidence of energetic electrons produced by electron-cyclotron heatings for end-loss-plugging potential formation, since these electrons have contributed to disturb these ion signals from conventional end-loss-ion detectors.

  20. The Specificity of Observational Studies in Physical Activity and Sports Sciences: Moving Forward in Mixed Methods Research and Proposals for Achieving Quantitative and Qualitative Symmetry.

    Science.gov (United States)

    Anguera, M Teresa; Camerino, Oleguer; Castañer, Marta; Sánchez-Algarra, Pedro; Onwuegbuzie, Anthony J

    2017-01-01

    Mixed methods studies are been increasingly applied to a diversity of fields. In this paper, we discuss the growing use-and enormous potential-of mixed methods research in the field of sport and physical activity. A second aim is to contribute to strengthening the characteristics of mixed methods research by showing how systematic observation offers rigor within a flexible framework that can be applied to a wide range of situations. Observational methodology is characterized by high scientific rigor and flexibility throughout its different stages and allows the objective study of spontaneous behavior in natural settings, with no external influence. Mixed methods researchers need to take bold yet thoughtful decisions regarding both substantive and procedural issues. We present three fundamental and complementary ideas to guide researchers in this respect: we show why studies of sport and physical activity that use a mixed methods research approach should be included in the field of mixed methods research, we highlight the numerous possibilities offered by observational methodology in this field through the transformation of descriptive data into quantifiable code matrices, and we discuss possible solutions for achieving true integration of qualitative and quantitative findings.

  1. On the Specification of Full Contracts

    DEFF Research Database (Denmark)

    Okika, Joseph; Ravn, Anders Peter; Fenech, Stephen

    2009-01-01

    Contracts specify properties of an interface to a software component. We consider the problem of de ning a full contract that speci es not only the normal behaviour, but also special cases and tolerated exceptions. In this paper we focus on the behavioural properties of use cases taken from...... the Common Component Modelling Example (CoCoME), proposed as a benchmark to compare di erent component models. We rst give the full speci cation of the use cases in the deontic-based speci cation language CL, and then we concentrate on three particular properties in order to compare deontic and operational...

  2. Determinação de proteínas totais via espectrofometria: vantagens e desvantagens dos métodos existentes Determination of total protein by spectrophotometry: advantages and disadvantages of proposed methods

    Directory of Open Access Journals (Sweden)

    Dimas A. M. Zaia

    1998-11-01

    Full Text Available Spectrophotometric determination of total protein is used in several areas such as clinical analysis, food science and technology, biochemistry, protein chemistry, physiology. Five spectrophotometric methods are mostly used: biuret, Lowry, Bradford, Smith and UV absorption. In this review a general overview of these methods is presented (interferences, applications; other methodologies are also discussed.

  3. Design for a sustainable society utilizing information and communication technologies (ICT) - proposal: a new EcoDesign method and its application

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, J. [Research Center for Advanced Science and Technology, the Univ. of Tokyo (Japan); Matsumoto, M. [Fundamental and Environment Labs., NEC Corp. (Japan)

    2004-07-01

    We discuss a new EcoDesign method, with a goal of improving the economy, and its application to a sustainable networked society. The new EcoDesign method differs from conventional EcoDesign in three respects: it utilizes a top-down approach, project-style research, and fact-finding and benchmarking. We systematize EcoDesign for a networked society from the viewpoint of technology and divide it into four components. Feasibility studies of the individual components reveal that if we promote ICT diffusion with EcoDesign in mind, we can suppress CO2 emissions and move towards a more sustainable society. (orig.)

  4. Analysis for trace mercury concentration. I. Critical evaluation of current procedures. II. A proposed method for determination by instrumental neutron activation analysis

    International Nuclear Information System (INIS)

    Litman, R.

    1975-01-01

    Current methods of sample pretreatments, digestion, lyophilization and extraction, have been found to lead to considerable loss of mercury, at an initial mercury concentration of 1 μg/g, and less. Storage of solutions of mercury at concentrations of less than 1 μg/ml, in glass, Teflon and polyethylene containers, leads to losses by adsorption. Electrochemical reduction of mercury to the metal, and subsequent volatilization, is postulated as the mechanism of loss from the samples studied during lyophilization. A method of instrumental neutron activation analysis, which obviates the above pretreatments, has been developed for mercury concentrations as low as 1 ng/ml

  5. Biclique cryptanalysis of the full AES

    DEFF Research Database (Denmark)

    Bogdanov, Andrey; Khovratovich, Dmitry; Rechberger, Christian

    2011-01-01

    Since Rijndael was chosen as the Advanced Encryption Standard (AES), improving upon 7-round attacks on the 128-bit key variant (out of 10 rounds) or upon 8-round attacks on the 192/256-bit key variants (out of 12/14 rounds) has been one of the most difficult challenges in the cryptanalysis of block...... ciphers for more than a decade. In this paper, we present the novel technique of block cipher cryptanalysis with bicliques, which leads to the following results: The first key recovery method for the full AES-128 with computational complexity 2126.1. The first key recovery method for the full AES-192...... with computational complexity 2189.7. The first key recovery method for the full AES-256 with computational complexity 2254.4. Key recovery methods with lower complexity for the reduced-round versions of AES not considered before, including cryptanalysis of 8-round AES-128 with complexity 2124.9. Preimage search...

  6. Developed Turbulence: From Full Simulations to Full Mode Reductions

    NARCIS (Netherlands)

    Grossmann, Siegfried; Lohse, Detlef; Reeh, Achim

    1996-01-01

    Developed Navier-Stokes turbulence is simulated with varying wave-vector mode reductions. The flatness and the skewness of the velocity derivative depend on the degree of mode reduction. They show a crossover towards the value of the full numerical simulation when the viscous subrange starts to be

  7. Establishment of the upper reference limit for thyroid peroxidase autoantibodies according to the guidelines proposed by the National Academy of Clinical Biochemistry: comparison of five different automated methods.

    Science.gov (United States)

    D'Aurizio, Federica; Metus, Paolo; Polizzi Anselmo, Annalisa; Villalta, Danilo; Ferrari, Anna; Castello, Roberto; Giani, Graziella; Tonutti, Elio; Bizzaro, Nicola; Tozzoli, Renato

    2015-12-01

    The estimation of the upper reference limit (URL) for autoantibodies against thyroid peroxidase (TPOAbs) is a controversial issue, because of an uncertainty associated with the criteria used to correctly define the reference population. In addition, the URL of TPOAbs is method-dependent and often arbitrarily established in current laboratory practice. The aim of this study was to determine the reference limits of TPOAbs in a male sample according to the National Academy of Clinical Biochemistry (NACB) guidelines, and to compare them with those obtained in a female group, for five third-generation commercial-automated immunoassay (IMA) platforms. 120 healthy males and 120 healthy females with NACB-required characteristics (younger than 30 years, TSH between 0.5 and 2.0 mIU/L, normal thyroid ultrasound, absence of thyroid disease and absence of other autoimmune diseases) were studied. Sera were analyzed for TPOAbs concentration using five IMA methods applied in automated analyzers: Immulite 2000 XPi (IMM); Maglumi 2000 Plus (MAG); Kryptor Compact Plus (KRY); Phadia 250 (PHA) and Liaison XL (LIA). A statistically significant difference (p reference group for a disease (such as AITD) that affects mainly females. However, in spite of the harmonization among methods provided by the use of an international standard preparation, the wide dispersion of quantitative results still observed in this study suggests the need for further efforts to better understand the cause of these discrepancies, focusing on TPO antigen preparations as the possible source of variability among different assays.

  8. Full traveltime inversion in source domain

    KAUST Repository

    Liu, Lu

    2017-06-01

    This paper presents a new method of source-domain full traveltime inversion (FTI). The objective of this study is automatically building near-surface velocity using the early arrivals of seismic data. This method can generate the inverted velocity that can kinetically best match the reconstructed plane-wave source of early arrivals with true source in source domain. It does not require picking first arrivals for tomography, which is one of the most challenging aspects of ray-based tomographic inversion. Besides, this method does not need estimate the source wavelet, which is a necessity for receiver-domain wave-equation velocity inversion. Furthermore, we applied our method on one synthetic dataset; the results show our method could generate a reasonable background velocity even when shingling first arrivals exist and could provide a good initial velocity for the conventional full waveform inversion (FWI).

  9. Full validation of a method for the determination of drugs of abuse in non-mineralized dental biofilm using liquid chromatography-tandem mass spectrometry and application to postmortem samples.

    Science.gov (United States)

    Henkel, Kerstin; Altenburger, Markus J; Auwärter, Volker; Neukamm, Merja A

    2018-01-01

    Alternative matrices play a major role in postmortem forensic toxicology, especially if common matrices (like body fluids or hair) are not available. Incorporation of illicit and medicinal drugs into non-mineralized dental biofilm (plaque) seems likely but has not been investigated so far. Analysis of plaque could therefore extend the spectrum of potentially used matrices in postmortem toxicology. For this reason, a rapid, simple and sensitive method for the extraction, determination and quantification of ten drugs of abuse from plaque using liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed and fully validated. Amphetamine, methamphetamine, 3,4-methylenedioxymethamphetamine (MDMA), 3,4-methylenedioxy-N-ethylamphetamine (MDEA), 3,4-methylenedioxyamphetamine (MDA), cocaine, benzoylecgonine, morphine, codeine and 6-acetylmorphine were extracted from 2mg of dried and powdered plaque via ultrasonication with acetonitrile. The extracts were analyzed on a triple-quadrupole linear ion trap mass spectrometer in scheduled multiple reaction monitoring mode (sMRM). The method was fully validated and proved accurate, precise, selective and specific with satisfactory linearity within the calibrated ranges. The lower limit of quantification was 10-15pgmg -1 for all compounds except for MDA (100pgmg -1 ) and amphetamine (200pgmg -1 ). The method has been successfully applied to three authentic postmortem samples with known drug history. Amphetamine, MDMA, cocaine, benzoylecgonine, morphine and codeine could be detected in these cases in concentrations ranging from 18pgmg -1 for cocaine to 1400pgmg -1 for amphetamine. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. Comparison of conventional liquid chromatography-tandem mass spectrometry versus microflow liquid chromatography-tandem mass spectrometry within the framework of full method validation for simultaneous quantification of 40 antidepressants and neuroleptics in whole blood.

    Science.gov (United States)

    Steuer, Andrea E; Poetzsch, Michael; Koenig, Magdalena; Tingelhoff, Eva; Staeheli, Sandra N; Roemmelt, Andreas T; Kraemer, Thomas

    2015-02-13

    Microflow liquid chromatography (MFLC) coupled to mass spectrometry (MS) is claimed to improve analysis throughput, reduce matrix effects and lower mobile phase consumption. This statement was checked within the framework of method validation of a multi-analyte procedure in clinical and forensic toxicology employing MFLC-MS/MS and conventional LC-MS/MS. 200 μL whole blood were spiked with 50 μL internal standard mixture and extracted by protein precipitation. The concentrated extract was separated into two vials. One was analyzed using a Thermo Fisher Ultimate liquid chromatography system coupled to an ABSciex 5500 QTrap mass spectrometer (LC-MS/MS) and one by an ABSciex Eksigent Microflow LC system coupled to an ABSciex 4500 linear ion trap quadrupole MS (MFLC-MS/MS). Both methods were fully validated and compared in terms of selectivity, stability, limits, calibration model, recovery (RE), matrix effects (ME), bias, imprecision and beta tolerance interval for 40 antidepressants and neuroleptics including 9 metabolites. Both methods had comparable LODs, LOQs and calibration models with some exceptions. The MFLC system showed slightly higher coefficients of variation (CVs) in the RE experiments. ME were reproducible in both systems but with lower CVs in the conventional LC system. Acceptance criteria for imprecision and bias were fulfilled for 32 analytes on the LC and for 28 analytes on the MFLC system. Beta tolerance intervals indicated better reproducibility in terms of narrower intervals for the conventional LC system. The advantages of the MFLC system were low mobile phase consumption, short run time, and better peak separation. The systems were comparable in terms of peak interference, LOD, ME, bias and imprecision. The advantages of the conventional LC system were more data points per peak, linear calibration models, stable retention times and better beta tolerance intervals. Due to higher robustness, the conventional LC system was finally chosen for

  11. Development and full validation of an UPLC-MS/MS method for the determination of an anti-allergic indolinone derivative in rat plasma, and application to a preliminary pharmacokinetic study.

    Science.gov (United States)

    Oufir, Mouhssin; Sampath, Chethan; Butterweck, Veronika; Hamburger, Matthias

    2012-08-01

    The natural product (E,Z)-3-(4-hydroxy-3,5-dimethoxybenzylidene)indolin-2-one (indolinone) was identified some years ago as a nanomolar inhibitor of FcɛRI-receptor dependent mast cell degranulation. To further explore the potential of the compound, we established an UPLC-MS/MS assay for dosage in rat plasma. The method was fully validated according to FDA Guidance for industry. Results of this validation and long term stability study demonstrate that the method in lithium heparinized rat plasma is specific, accurate, precise and capable of producing reliable results according to recommendations of international guidelines. The method was validated with a LLOQ of 30.0 ng/mL and an ULOQ of 3000 ng/mL. The response versus concentration data were fitted with a first order polynomial with 1/X(2) weighting. No matrix effect was observed when using three independent sources of rat plasma. The average extraction recovery was consistent over the investigated range. This validation in rat plasma demonstrated that indolinone was stable for 190 days when stored below -65 °C; for 4 days at 10 °C in the autosampler; for 4h at RT, and during three successive freeze/thaw cycles at -65 °C. Preliminary pharmacokinetic data were obtained in male Sprague-Dawley rats (2 mg/kg BW i.v.). Blood samples taken from 0 to 12 h after injection were collected, and data analyzed with WinNonlin. A short half-life (4.30±0.14 min) and a relatively high clearance (3.83±1.46 L/h/kg) were found. Copyright © 2012 Elsevier B.V. All rights reserved.

  12. Irradiation with x-rays of the energy 18 MV induces radioactivity in transfusion blood: Proposal of a safe method using 6 MV.

    Science.gov (United States)

    Frentzel, Katharina; Badakhshi, Harun

    2016-12-01

    To prevent a fatal transfusion-associated graft-versus-host disease, it is recommended to irradiate transfusion blood and blood components with ionizing radiation. Using x-rays from a linear accelerator of the radiotherapy department is an accepted alternative to gamma irradiation devices of the blood bank and to the orthovoltage units that are replacing the gamma irradiators today. However, the use of high energy x-rays may carry a potential risk of induced radioactivity. The objective of this study was to investigate the effect of two different energy levels, 6 and 18 MV, which are executed in routine clinical settings. The research question was if induced radioactivity occurs at one of these standard energy levels. The authors aimed to give a proposal for a blood irradiation procedure that certainly avoids induced radioactivity. For this study, the authors developed a blood bag phantom, irradiated it with x-ray energies of 6 and 18 MV, and measured the induced radioactivity in a well counter. Thereafter, the same irradiation and measuring procedure was performed with a unit of packed red blood cells. A feasible clinical procedure was developed using 6 MV and an acrylic box. With the irradiation planning system XiO, the authors generated an irradiation protocol for the linear accelerator Siemens ONCOR Anvant-Garde. Both measurement setups showed that there was induced radioactivity for 18 MV but not for 6 MV. The induced radioactivity for 18 MV was up to 190 times the background. This is significant and of clinical relevance especially since there are newborn and fetal blood recipients for whom every radiation exposure has to be strictly avoided. The irradiation of blood with x-rays from a linear accelerator of the radiotherapy department is safe and feasible, but by the current state of scientific knowledge, the authors recommend to use an x-ray energy of 6 MV or less to avoid induced radioactivity in transfusion blood.

  13. Fuel- and wood consumption surveys in developing countries: a proposal of an efficient low-cost method and the results of its application in eastern Ethiopia

    Energy Technology Data Exchange (ETDEWEB)

    Poschen, P.; Eiche, G.

    1986-01-01

    The method involves a preliminary survey to establish areas homogeneous for temperature and rainfall regime, natural vegetation, agricultural systems, wood fuel substitutes, housing and cooking habits. Locations are sampled within such areas to reflect variability in presence of forests and other fuel and wood resources, population density, and access to markets. Households are sampled within a location to cover variation in social structure. Results from a survey in the Hararghe highlands differ markedly from previous Ethiopia-wide estimates and show that remaining wood resources supply less than half of the fuel requirements. An effective community forestry programme is urgently required. (Refs. 9).

  14. Transport of momentum in full f gyrokinetics

    International Nuclear Information System (INIS)

    Parra, Felix I.; Catto, Peter J.

    2010-01-01

    Full f electrostatic gyrokinetic formulations employ two gyrokinetic equations, one for ions and the other for electrons, and quasineutrality to obtain the ion and electron distribution functions and the electrostatic potential. We demonstrate with several examples that the long wavelength radial electric field obtained with full f approaches is extremely sensitive to errors in the ion and electron density since small deviations in density give rise to large, nonphysical deviations in the conservation of toroidal angular momentum. For typical tokamak values, a relative error of 10 -7 in the ion or electron densities is enough to obtain the incorrect toroidal rotation. Based on the insights gained with the examples considered, three simple tests to check transport of toroidal angular momentum in full f simulations are proposed.

  15. Full-F gyrofluid model

    DEFF Research Database (Denmark)

    Madsen, Jens

    2013-01-01

    variables. The fluid moment hierarchy is closed by approximating the gyrokinetic distribution function as a finite order Hermite-Laguerre polynomial and by determining closure approximations for terms involving the gyrokinetic gyro-averaging operator. The model exactly conserves the gyrokinetic full......A global electromagnetic gyrofluid model based on the full-F gyrokinetic model is derived. The gyrofluid moment variables are not split into fluctuating and equilibrium parts. Profiles are evolved freely, and gyro-averaging operators are not parametrized, but are functions of the gyrofluid moment...

  16. Determination of in-situ thermal properties of Stripa granite from temperature measurements in the full-scale heater experiments: method and preliminary results. Technical information report No. 24

    International Nuclear Information System (INIS)

    Jeffry, J.A.; Chan, T.; Cook, N.G.W.; Witherspoon, P.A.

    1979-05-01

    The in-situ thermal conductivity and thermal diffusivity of a granite rock mass at the Stripa mine, Sweden, have been extracted from the first 70 days of temperature data for the 5 kW full-scale heater experiment by means of least-squares fit to a finite-line source solution. Thermal conductivity and thermal diffusivity have been determined to be 3.69 W/(m- 0 C) and 1.84 x 10 -6 m 2 /s, respectively, at an average rock temperature of 23 0 C (the average value of the actual temperature data used). These values are only slightly higher than the corresponding laboratory values, i.e., there is no significant size effect in the thermal properties of this rock mass. Since the size and shape of the heater canister used are similar to those considered for nuclear waste canisters and a substantial volume of rock is heated, the thermal properties obtained in this study are representative of in-situ rock mass properties under actual nuclear repository operating conditions

  17. The Fiction of Full BEKK

    NARCIS (Netherlands)

    C-L. Chang (Chia-Lin); M.J. McAleer (Michael)

    2017-01-01

    textabstractThe purpose of the paper is to show that univariate GARCH is not a special case of multivariate GARCH, specifically the Full BEKK model, except under parametric restrictions on the off-diagonal elements of the random coefficient autoregressive coefficient matrix, provides the regularity

  18. Empty calories and phantom fullness

    NARCIS (Netherlands)

    Camps, Guido; Mars, Monica; Graaf, de Kees; Smeets, Paul A.M.

    2016-01-01

    Background: Stomach fullness is a determinant of satiety. Although both the viscosity and energy content have been shown to delay gastric emptying, their relative importance is not well understood. Objective: We compared the relative effects of and interactions between the viscosity and energy

  19. Toward full MOX core design

    International Nuclear Information System (INIS)

    Rouviere, G.; Guillet, J.L.; Bruna, G.B.; Pelet, J.

    1999-01-01

    This paper presents a selection of the main preliminary results of a study program sponsored by COGEMA and currently carried out by FRAMATOME. The objective of this study is to investigate the feasibility of full MOX core loading in a French 1300 MWe PWR, a recent and widespread standard nuclear power plant. The investigation includes core nuclear design, thermal hydraulic and systems aspects. (authors)

  20. Rectilinear Full Steiner Tree Generation

    DEFF Research Database (Denmark)

    Zachariasen, Martin

    1999-01-01

    The fastest exact algorithm (in practice) for the rectilinear Steiner tree problem in the plane uses a two-phase scheme: First, a small but sufficient set of full Steiner trees (FSTs) is generated and then a Steiner minimum tree is constructed from this set by using simple backtrack search, dynamic...

  1. Full autonomy; Autarkie im Komplettpaket

    Energy Technology Data Exchange (ETDEWEB)

    Augsten, Eva

    2011-05-31

    Normally, those who talk of full solar autonomy refer to the annual balance of a house. Now, architect Timo Leukefeld and Helma Eigenheimbau AG presented a really autonomous solar house which is available on a turnkey basis for 363,000 Euros.

  2. [Endoscopic full-thickness resection].

    Science.gov (United States)

    Meier, B; Schmidt, A; Caca, K

    2016-08-01

    Conventional endoscopic resection techniques such as endoscopic mucosal resection (EMR) or endoscopic submucosal dissection (ESD) are powerful tools for the treatment of gastrointestinal (GI) neoplasms. However, those techniques are limited to the superficial layers of the GI wall (mucosa and submucosa). Lesions without lifting sign (usually arising from deeper layers) or lesions in difficult anatomic positions (appendix, diverticulum) are difficult - if not impossible - to resect using conventional techniques, due to the increased risk of complications. For larger lesions (>2 cm), ESD appears to be superior to the conventional techniques because of the en bloc resection, but the procedure is technically challenging, time consuming, and associated with complications even in experienced hands. Since the development of the over-the-scope clips (OTSC), complications like bleeding or perforation can be endoscopically better managed. In recent years, different endoscopic full-thickness resection techniques came to the focus of interventional endoscopy. Since September 2014, the full-thickness resection device (FTRD) has the CE marking in Europe for full-thickness resection in the lower GI tract. Technically the device is based on the OTSC system and combines OTSC application and snare polypectomy in one step. This study shows all full-thickness resection techniques currently available, but clearly focuses on the experience with the FTRD in the lower GI tract.

  3. Proposed Method for Estimating Health-Promoting Glucosinolates and Hydrolysis Products in Broccoli (Brassica oleracea var. italica) Using Relative Transcript Abundance.

    Science.gov (United States)

    Becker, Talon M; Jeffery, Elizabeth H; Juvik, John A

    2017-01-18

    Due to the importance of glucosinolates and their hydrolysis products in human nutrition and plant defense, optimizing the content of these compounds is a frequent breeding objective for Brassica crops. Toward this goal, we investigated the feasibility of using models built from relative transcript abundance data for the prediction of glucosinolate and hydrolysis product concentrations in broccoli. We report that predictive models explaining at least 50% of the variation for a number of glucosinolates and their hydrolysis products can be built for prediction within the same season, but prediction accuracy decreased when using models built from one season's data for prediction of an opposing season. This method of phytochemical profile prediction could potentially allow for lower phytochemical phenotyping costs and larger breeding populations. This, in turn, could improve selection efficiency for phase II induction potential, a type of chemopreventive bioactivity, by allowing for the quick and relatively cheap content estimation of phytochemicals known to influence the trait.

  4. Dynamic risk assessment method – a proposal for assessing risk in water supply system / Metoda dynamicznego szacowania ryzyka – propozycja oceny ryzyka w systemie zaopatrzenia wody

    Directory of Open Access Journals (Sweden)

    Fortmann-Roe Scott

    2015-06-01

    Full Text Available Dynamika Systemów jest metodologią modelowania i analizy złożonych systemów. Taki złożony system może być charakteryzowany przez wzajemne proste połączenia elementów oraz istniejące sprzężenia zwrotne. Przeprowadzenie oceny ryzyka przy modelowaniu Systemów Dynamicznych jest trudnym wyzwaniem. Chociaż w niektórych przypadkach, uzyskane za pomocą symulacji serie wyników mogą się wydawać przypadkowe, to jednak często istnieje wysoki stopień autokorelacji między tymi seriami wynikający z istnienia powiązań zwrotnych w systemie. Artykuł przedstawia propozycje Metody Dynamicznego Szacowania Ryzyka (MDSR, która pozwala oceniać ryzyko związane z hipotetycznymi kosztami zachorowań wywołanymi skażeniem systemu zaopatrzenia w wodę przez Cryptosporidium.

  5. Full-duplex optical communication system

    Science.gov (United States)

    Shay, Thomas M. (Inventor); Hazzard, David A. (Inventor); Horan, Stephen (Inventor); Payne, Jason A. (Inventor)

    2004-01-01

    A method of full-duplex electromagnetic communication wherein a pair of data modulation formats are selected for the forward and return data links respectively such that the forward data electro-magnetic beam serves as a carrier for the return data. A method of encoding optical information is used wherein right-hand and left-hand circular polarizations are assigned to optical information to represent binary states. An application for an earth to low earth orbit optical communications system is presented which implements the full-duplex communication and circular polarization keying modulation format.

  6. Stroboscope Based Synchronization of Full Frame CCD Sensors

    Directory of Open Access Journals (Sweden)

    Liang Shen

    2017-04-01

    Full Text Available The key obstacle to the use of consumer cameras in computer vision and computer graphics applications is the lack of synchronization hardware. We present a stroboscope based synchronization approach for the charge-coupled device (CCD consumer cameras. The synchronization is realized by first aligning the frames from different video sequences based on the smear dots of the stroboscope, and then matching the sequences using a hidden Markov model. Compared with current synchronized capture equipment, the proposed approach greatly reduces the cost by using inexpensive CCD cameras and one stroboscope. The results show that our method could reach a high accuracy much better than the frame-level synchronization of traditional software methods.

  7. Full Waveform Inversion for Reservoir Characterization - A Synthetic Study

    KAUST Repository

    Zabihi Naeini, E.

    2017-05-26

    Most current reservoir-characterization workflows are based on classic amplitude-variation-with-offset (AVO) inversion techniques. Although these methods have generally served us well over the years, here we examine full-waveform inversion (FWI) as an alternative tool for higher-resolution reservoir characterization. An important step in developing reservoir-oriented FWI is the implementation of facies-based rock physics constraints adapted from the classic methods. We show that such constraints can be incorporated into FWI by adding appropriately designed regularization terms to the objective function. The advantages of the proposed algorithm are demonstrated on both isotropic and VTI (transversely isotropic with a vertical symmetry axis) models with pronounced lateral and vertical heterogeneity. The inversion results are explained using the theoretical radiation patterns produced by perturbations in the medium parameters.

  8. New methods in order to determine the extent of temporary blinding from laser and LED light and proposal how to allocate into blinding groups

    Science.gov (United States)

    Reidenbach, Hans-Dieter; Ott, Günter; Brose, Martin; Dollinger, Klaus

    2010-02-01

    recovery time tVA has been found to obey the dose relationship: tVA /s ~ 3.7•ln(energy/μJ) - 16.2 in the case of a green HB-LED in the power range 0.12 mW to 1.5 mW and for exposure durations between 1 s and 8 s. Further investigations were performed with other LED colors especially as far as threshold values for temporary blinding are concerned. The afterimage duration tafterimage,fv produced by a red laser beam was determined to be: tafterimage,fv/s ~ 50.6•ln[(P•texp)/μJ] - 13.4, for laser output powers P between 10 μW and 30 μW with exposure durations texp from 0.25 s up to 10 s, when the beam hits the fovea. Additional results have been achieved with a green laser at a wavelength of 532 nm and compared with the respective values at 632.8 nm. The results of the research project suggest classifying light sources like laser and LEDs into so-called blinding groups. In total 3 different groups which reflect the obtained results and are proposed in order to fulfil the requirements of special classification and might be regarded as an appropriate assistance to perform a risk analysis.

  9. TH-AB-207A-07: Radiation Dose Simulation for a Newly Proposed Dynamic Bowtie Filters for CT Using Fast Monte Carlo Methods

    Energy Technology Data Exchange (ETDEWEB)

    Liu, T; Lin, H; Gao, Y; Caracappa, P; Wang, G; Cong, W; Xu, X [Rensselaer Polytechnic Institute, Troy, NY (United States)

    2016-06-15

    Purpose: Dynamic bowtie filter is an innovative design capable of modulating the X-ray and balancing the flux in the detectors, and it introduces a new way of patient-specific CT scan optimizations. This study demonstrates the feasibility of performing fast Monte Carlo dose calculation for a type of dynamic bowtie filter for cone-beam CT (Liu et al. 2014 9(7) PloS one) using MIC coprocessors. Methods: The dynamic bowtie filter in question consists of a highly attenuating bowtie component (HB) and a weakly attenuating bowtie (WB). The HB is filled with CeCl3 solution and its surface is defined by a transcendental equation. The WB is an elliptical cylinder filled with air and immersed in the HB. As the scanner rotates, the orientation of WB remains the same with the static patient. In our Monte Carlo simulation, the HB was approximated by 576 boxes. The phantom was a voxelized elliptical cylinder composed of PMMA and surrounded by air (44cm×44cm×40cm, 1000×1000×1 voxels). The dose to the PMMA phantom was tallied with 0.15% statistical uncertainty under 100 kVp source. Two Monte Carlo codes ARCHER and MCNP-6.1 were compared. Both used double-precision. Compiler flags that may trade accuracy for speed were avoided. Results: The wall time of the simulation was 25.4 seconds by ARCHER on a 5110P MIC, 40 seconds on a X5650 CPU, and 523 seconds by the multithreaded MCNP on the same CPU. The high performance of ARCHER is attributed to the parameterized geometry and vectorization of the program hotspots. Conclusion: The dynamic bowtie filter modeled in this study is able to effectively reduce the dynamic range of the detected signals for the photon-counting detectors. With appropriate software optimization methods, the accelerator-based (MIC and GPU) Monte Carlo dose engines have shown good performance and can contribute to patient-specific CT scan optimizations.

  10. A full-parallax 3D display with restricted viewing zone tracking viewer's eye

    Science.gov (United States)

    Beppu, Naoto; Yendo, Tomohiro

    2015-03-01

    The Three-Dimensional (3D) vision became widely known as familiar imaging technique now. The 3D display has been put into practical use in various fields, such as entertainment and medical fields. Development of 3D display technology will play an important role in a wide range of fields. There are various ways to the method of displaying 3D image. There is one of the methods that showing 3D image method to use the ray reproduction and we focused on it. This method needs many viewpoint images when achieve a full-parallax because this method display different viewpoint image depending on the viewpoint. We proposed to reduce wasteful rays by limiting projector's ray emitted to around only viewer using a spinning mirror, and to increase effectiveness of display device to achieve a full-parallax 3D display. We propose a method by using a tracking viewer's eye, a high-speed projector, a rotating mirror that tracking viewer (a spinning mirror), a concave mirror array having the different vertical slope arranged circumferentially (a concave mirror array), a cylindrical mirror. About proposed method in simulation, we confirmed the scanning range and the locus of the movement in the horizontal direction of the ray. In addition, we confirmed the switching of the viewpoints and convergence performance in the vertical direction of rays. Therefore, we confirmed that it is possible to realize a full-parallax.

  11. A proposal for a test method for assessment of hazard property HP 12 (“Release of an acute toxic gas”) in hazardous waste classification - Experience from 49 waste

    OpenAIRE

    Hennebert , Pierre; Samaali , Ismahen; Molina , Pauline

    2016-01-01

    International audience; A stepwise method for assessment of the HP 12 is proposed and tested with 49 waste samples. The hazard property HP 12 is defined as “Release of an acute toxic gas”: waste which releases acute toxic gases (Acute Tox. 1, 2 or 3) in contact with water or an acid. When a waste contains a substance assigned to one of the following supplemental hazards EUH029, EUH031 and EUH032, it shall be classified as hazardous by HP 12 according to test methods or guidelines (EC, 2014a, ...

  12. Claimed Effects, Outcome Variables and Methods of Measurement for Health Claims on Foods Related to Vision Proposed Under Regulation (EC) 1924/2006

    Science.gov (United States)

    Bedogni, Giorgio; Biasini, Beatrice; Zavaroni, Ivana; Ventura, Marco; Galli, Daniela; Mirandola, Prisco; Vitale, Marco; Bonadonna, Riccardo C.; Passeri, Giovanni

    2018-01-01

    Adequate visual function has a strong impact on the quality of life of people. Several foods and food components have been hypothesized to play a role in the maintenance of normal visual function and in the prevention of eye diseases. Some of these foods/food components have been the object of a request of authorization for use of health claims under Articles 13(5) or 14 of the Regulation (EC) 1924/2006. Most of these requests have received a negative opinion from the European Food Safety Authority (EFSA) due to the choice of inappropriate outcome variables (OVs) and/or methods of measurement (MMs) applied in the studies used to substantiate the claims. This manuscript refers to the collection, collation and critical analysis of OVs and MMs related to vision. Guidance document and requests for authorization of health claims were used to collect OVs and MMs related to vision. A literature review was performed to critically analyse OVs and MMs, with the aim of defining their appropriateness in the context of a specific claimed effect related to vision. The results highlight the importance of adequate choices of OVs and MMs for an effective substantiation of claims related to visual function. PMID:29443929

  13. Computational tool kit for evaluating air kerma with the purpose of radiation protection of hospital inpatients: proposal of a simple experimental evaluation method

    Energy Technology Data Exchange (ETDEWEB)

    Hoff, Gabriela; Fischer, Andreia Caroline Fischer da Silveira, E-mail: ghoff.gesic@gmail.com [Pontificia Universidade Catolica do Rio Grande do Sul (PUCRS), Porto Alegre, RS, (Brazil); Andrade, Jose Rodrigo Mendes; Bacelar, Alexandre [Service of Medical Physics and Radioprotection, Hospital de Clinicas de Porto Alegre (HCPA), Porto Alegre, RS (Brazil)

    2012-03-15

    Objective: To present a data analysis toolkit that may be utilized with the purpose of radiation protection of hospital inpatients and workers in areas where mobile apparatuses are used. Materials and methods: an Excel Active Sheet was utilized to develop a computational toolkit with exposure measurements to generate a database of shape factors and to calculate the air kerma around hospital beds. The initial database included data collected with three mobile apparatuses. A non-anthropomorphic phantom was utilized and exposure measurements were performed on a (4.2 x 4.2) m{sup 2} mesh-grid at 0.3 m steps. Results: The toolkit calculates the air kerma (associated with patients' radiation exposure and with ambient equivalent dose) under secondary radiation. For distances lower than 60.0 cm, values above the maximum ambient equivalent dose threshold defined for radiation free areas (0.5 mSv/year) were verified. Data collected at 2.1 m have always presented values lower than 12% of that threshold. Conclusion: The toolkit can aid in the radiological protection of patients and workers, provided it is combined with appropriate data collection, since it allows the determination of radiation free areas around beds in rooms where mobile X-ray apparatuses are utilized. (author)

  14. Computational tool kit for evaluating air kerma with the purpose of radiation protection of hospital inpatients: proposal of a simple experimental evaluation method

    International Nuclear Information System (INIS)

    Hoff, Gabriela; Fischer, Andreia Caroline Fischer da Silveira; Andrade, Jose Rodrigo Mendes; Bacelar, Alexandre

    2012-01-01

    Objective: To present a data analysis toolkit that may be utilized with the purpose of radiation protection of hospital inpatients and workers in areas where mobile apparatuses are used. Materials and methods: an Excel Active Sheet was utilized to develop a computational toolkit with exposure measurements to generate a database of shape factors and to calculate the air kerma around hospital beds. The initial database included data collected with three mobile apparatuses. A non-anthropomorphic phantom was utilized and exposure measurements were performed on a (4.2 x 4.2) m 2 mesh-grid at 0.3 m steps. Results: The toolkit calculates the air kerma (associated with patients' radiation exposure and with ambient equivalent dose) under secondary radiation. For distances lower than 60.0 cm, values above the maximum ambient equivalent dose threshold defined for radiation free areas (0.5 mSv/year) were verified. Data collected at 2.1 m have always presented values lower than 12% of that threshold. Conclusion: The toolkit can aid in the radiological protection of patients and workers, provided it is combined with appropriate data collection, since it allows the determination of radiation free areas around beds in rooms where mobile X-ray apparatuses are utilized. (author)

  15. Full-wave current conveyor precision rectifier

    Directory of Open Access Journals (Sweden)

    Đukić Slobodan R.

    2008-01-01

    Full Text Available A circuit that provides precision rectification of small signal with low temperature sensitivity for frequencies up to 100 kHz without waveform distortion is presented. It utilizes an improved second type current conveyor based on current-steering output stage and biased silicon diodes. The use of a DC current source to bias the rectifying diodes provides higher temperature stability and lower DC offset level at the output. Proposed design of the precision rectifier ensures good current transfer linearity in the range that satisfy class A of the amplifier and good voltage transfer characteristic for low level signals. Distortion during the zero crossing of the input signal is practically eliminated. Design of the proposed rectifier is realized with standard components.

  16. Full autonomous microline trace robot

    Science.gov (United States)

    Yi, Deer; Lu, Si; Yan, Yingbai; Jin, Guofan

    2000-10-01

    Optoelectric inspection may find applications in robotic system. In micro robotic system, smaller optoelectric inspection system is preferred. However, as miniaturizing the size of the robot, the number of the optoelectric detector becomes lack. And lack of the information makes the micro robot difficult to acquire its status. In our lab, a micro line trace robot has been designed, which autonomous acts based on its optoelectric detection. It has been programmed to follow a black line printed on the white colored ground. Besides the optoelectric inspection, logical algorithm in the microprocessor is also important. In this paper, we propose a simply logical algorithm to realize robot's intelligence. The robot's intelligence is based on a AT89C2051 microcontroller which controls its movement. The technical details of the micro robot are as follow: dimension: 30mm*25mm*35*mm; velocity: 60mm/s.

  17. Full system decontamination feasibility studies

    International Nuclear Information System (INIS)

    Denault, R.P.; LeSurf, J.E.; Walschot, F.W.

    1988-01-01

    Many chemical decontaminations have been performed on subsystems in light water reactors (BWRs and PWRs) but none on the full system (including the fuel) of large, (>500 MWe) investor owned reactors. Full system decontaminations on pressure-tubed reactors have been shown to facilitate maintenance, inspection, repair and replacement of reactor components. Further advantages are increased reactor availability and plant life extension. A conceptual study has been performed for EPRI (for PWRs) and Commonwealth Edison Co (for BWRs) into the applicability and cost benefit of full system decontaminations (FSD). The joint study showed that FSDs in both PWRs and BWRs, with or without the fuel included in the decontamination, are feasible and cost beneficial provided a large amount of work is to be done following the decontamination. The large amounts of radioactive waste generated can be managed using current technologies. Considerable improvements in waste handling, and consequent cost savings, can be obtained if new techniques which are now reaching commercial application are used. (author)

  18. LHCb : Full Experiment System Test

    CERN Multimedia

    Cattaneo, M

    2009-01-01

    LHCb had been planning to commission its High Level Trigger software and Data Quality monitoring procedures using real collisions data from the LHC pilot run. Following the LHC incident on 19th September 2008, it was decided to commission the system using simulated data. This “Full Experiment System Test” consists of: - Injection of simulated minimum bias events into the full HLT farm, after selection by a simulated Level 0 trigger. - Processing in the HLT farm to achieve the output rate expected for nominal LHC luminosity running, sustained over the typical duration of an LHC fill. - Real time Data Quality validation of the HLT output, validation of calibration and alignment parameters for use in the reconstruction. - Transmission of the event data, calibration data and book-keeping information to Tier1 sites and full reconstruction of the event data. - Data Quality validation of the reconstruction output. We will report on the preparations and results of FEST09, and on the status of commissioning for no...

  19. ASTM F739 method for testing the permeation resistance of protective clothing materials: critical analysis with proposed changes in procedure and test-cell design.

    Science.gov (United States)

    Anna, D H; Zellers, E T; Sulewski, R

    1998-08-01

    ASTM (American Society for Testing and Materials) Method F739-96 specifies a test-cell design and procedures for measuring the permeation resistance of chemical protective clothing. Among the specifications are open-loop collection stream flow rates of 0.050 to 0.150 L/min for a gaseous medium. At elevated temperatures the test must be maintained within 1 degree C of the set point. This article presents a critical analysis of the effect of the collection stream flow rate on the measured permeation rate and on the temperature uniformity within the test cell. Permeation tests were conducted on four polymeric glove materials with 44 solvents at 25 degrees C. Flow rates > 0.5 L/min were necessary to obtain accurate steady-state permeation rate (SSPR) values in 25 percent of the tests. At the lower flow rates the true SSPR typically was underestimated by a factor of two or less, but errors of up to 33-fold were observed. No clear relationship could be established between the need for a higher collection stream flow rate and either the vapor pressure or the permeation rate of the solvent, but test results suggest that poor mixing within the collection chamber was a contributing factor. Temperature gradients between the challenge and collection chambers and between the bottom and the top of the collection chamber increased with the water-bath temperature and the collection stream flow rate. Use of a test cell modified to permit deeper submersion reduced the gradients to < or = 0.5 degrees C. It is recommended that all SSPR measurements include verification of the adequacy of the collection stream flow rate. For testing at nonambient temperatures, the modified test cell described here could be used to ensure temperature uniformity throughout the cell.

  20. Symptom management in complex post-traumatic stress disorder (ICD-11), view and experience of patients and their relatives: a mixed methods approach (Research Proposal).

    Science.gov (United States)

    Stadtmann, Manuel P; Maercker, Andreas; Binder, Jochen; Schnepp, Wilfried

    2017-09-07

    Using the framework of IDC-11, complex post-traumatic stress disorder will be diagnosed using the core criteria of a post-traumatic stress disorder and the presence of at least one symptom from the following three domains: symptoms of emotional dysregulation, negative self-concept, and problems in interpersonal relationships. In the literature, these symptoms are discussed as a common reason for seeking treatment. The symptoms can influence and impair the quality of life. This article describes a mixed methods study with a sequential exploratory design. The aim is to describe specific patient characteristics, levels of symptom burden and perspectives of adult inpatients and to describe the experiences, views and needs of patients' relatives. The study will also investigate facilitators of and barriers to symptom management. The research will be conducted in four phases. The first phase will assess patients' symptom burdens. The second phase will use semi-structured interviews to explore attitudes to symptom management and perceptions of patients and their relatives. The third phase will statistically explore hypotheses generated after the qualitative interviews. The fourth phase will mix the quantitative and qualitative results and interpret critically. The present study will add new results to the growing literature on complex post-traumatic stress disorder. These results could serve as the basis for further research into the development of interventions to improve symptom management. Trial registration Ethical approval has been obtained from the Swiss cantonal ethic commission (Nr. 201500096). This research was also registered to the World Health Organization Clinical Trials Search Portal through the German Clinical Trial Register, Trial DRKS00012268 (21/04/2017).